... thermal energy recovery testing was also ... of the acceptance test procedure, the ... RECOVERY, *ACCEPTANCE TESTS, VOLUME, ENVIRONMENTS ...
DTIC Science & Technology
... Title : Recommended Acceptance Testing Procedure for Network Enabled Training Simulators. Descriptive Note : Technical rept. ...
The attached procedure provides the steps necessary to acceptance test the 244U DCRT electrical interlocks system.
Energy Citations Database
... Accession Number : ADA366656. Title : Acceptance Testing Procedures for Heating, Ventilating, and Air-Conditioning Systems. ...
This supporting document provides the Acceptance Test Procedure (ATP) for the acceptance and testing of the fire alarm system of mobile office MO-294.
This document provides the results of the Acceptance Test Procedure for the Honeywell Modular Automation System.
... Title : Development and Initial Evaluation of an Acceptance Testing Procedure for Air Supply and Distribution Systems in New Army Facilities. ...
This document outlines the steps required to properly document the acceptance testing of this prototypical device.
DOE Information Bridge
Acceptance Test Procedure for testing the Light Duty Utility Arm (LDUA) Overview Video Camera System (OVS).
National Technical Information Service (NTIS)
...Procedures for acceptance of testing facility. 160.062-8 Section 160.062-8 Shipping COAST GUARD, DEPARTMENT...Releases. Lifesaving Equipment, Hydraulic and Manual § 160.062-8 Procedures for acceptance of testing...
Code of Federal Regulations, 2010
This Acceptance Test Procedure (ATP) will test and verify that the Exhauster meets the specified functional requirements, safety requirements, operating requirements, and provide a record of the functional test results. The system/functions that will be tested are listed in ...
This Acceptance Test Procedure is to verify the correct reading of points connected to the Tank Monitor and Control System (TMACS).
Provides the software acceptance test plan and procedures for software that will perform data acquisition for the surface moisture measurement system.
... Accession Number : ADA141839. Title : Procedures for Acceptance Testing of Solar Energy Systems. Descriptive Note : Final rept.,. ...
This Acceptance/Operational Test Procedure will document the satisfactory operation of the 103-SY Camera Purge Control System.
Acceptance test procedure for Project W-030 Cathodic Protection Installation, 241-AY and 241-AZ Tank Farm Ventilation Upgrade.
... Acceptance Test Procedures for the SH-2F Helicopter Weapon System Trainer (Device 2F106) Software Conversion Modification. Revision D. ...
The TMACS Software Project Test Procedures translate the project`s acceptance criteria into test steps. Software releases are certified when the affected Test Procedures are successfully performed and the customers authorize installation of these changes. This ...
The procedure specified in acceptance testing of pozzolans for chemical analysis for major oxides is more involved and most costly than the procedure used for such analyses in the acceptance testing of portland cement. In order to investigate the simplifi...
This Acceptance Test Report (ATR) has been prepared to establish field testing procedures to demonstrate that the Electrical/Instrumentation systems function as intended by the design.
... Descriptors : *Signal generators, *Microwave equipment, Test methods, Central processing units, Acceptance tests, Range(Extremes), Computer ...
... TEST, ACCEPTANCE TEST PROCEDURE, PART III, RECEIVER- TRANSMITTER COUNTERMEASURES, EQUIPMENT RT-1079/ALQ-126. ...
This Factory Acceptance Test Procedure (FAT) is for the Westinghouse 100 Ton Hydraulic Trailer. The trailer will be used for the removal of the 101-SY pump. This procedure includes: safety check and safety procedures; pre-operation check out; startup; lev...
... It is shown that the usual acceptance sampling procedures based on mean life generally favor the producer (consumer) in the IFR (DFR) case. ...
This Acceptance Test Procedure/Operational Test Procedure (ATP/OTP) has been prepared to demonstrate that the Electrical/Instrumentation and Mechanical systems function as required by project criteria and to verify proper operation of the integrated system including the interlocks.
This acceptance test procedure (ATP) was written to test the void fraction instrument (VFI) and verify that the unit is ready for field service. The procedure verifies that the mechanical and electrical features (not specifically addressed in the software ATP) and software alarms are operating ...
This Acceptance Test Procedure was written to test the Enraf Series 854 Advanced Technology Gauge (ATG) prior to installation in the Tank Farms. The procedure sets various parameters and verifies that the gauge is functional.
On July 18, 1997, the Transuranic (TRU) glovebox was tested using glovebox acceptance test procedure 13021A-86. The primary focus of the glovebox acceptance test was to examine control system interlocks, display menus, alarms, and operator messages. Limit...
This Acceptance Test Report (ATR) documents the results of acceptance test procedure WHC-SD-WM-ATR-151. Included in this report is a summary of the tests, the results and issues, the signature and sign- off ATP pages, and a summarized table of the specifi...
This Acceptance Test Report (ATR) documents the results of acceptance test procedure WHC-SD-WM-ATR-151. Included in this report is a summary of the tests, the results and issues, the signature and sign- off ATP pages, and a summarized table of the specification vs. ATP ...
This Acceptance Test Report covers the results of the execution of the Acceptance Test Procedure for the 241-AN-107 Enraf Advanced Technology Gauges. The test verified the proper operation of the gauges to measure waste density and level in the 241-AN-107 tank.
The objective of this document is to report and interpret the findings of the isolation barrier acceptance tests performed in 105KE/100K. The tests were performed in accordance with the test plan (McCracken 1995c) and acceptance test procedure ...
The attached Test Procedure provides detailed test steps to assure proper operation of the 244U DCRT instrumentation.
This test report provides the results from the performance of Acceptance Test Procedure (ATP) HNF-4276, for Pumping and Instrumentation Control (PIC) skid 'K'. The ATP verifies the proper construction of the PIC skid 'K' by Site Fabrication Services along...
This test report provides the results from the performance of Acceptance Test Procedure (ATP) RPP-5489, for Pumping Instrumentation and Control (PIC) skid N. The ATP verifies the proper construction of the PIC skid N by Site Fabrication Services along wit...
This Acceptance Test Report for the PUREX Surveillance and Monitoring and Control System (SAMCONS) Uninterruptible Power Supply (UPS) Acceptance Test Procedure validates the operation of the UPS, all alarming and display functions and the ability of the U...
This acceptance test procedure is to document testing of added anodes to existing Rectifier No. 11. Anodes were added under Project W-151, Tank 101-AZ Waste Retrieval System.
This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping and Instrumentation Control (PIC) skid designed as ''N''. The ATP will be performed after the construction of the PIC skid in the shop.
This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''W''. The ATP will be performed after the construction of the PIC skid in the fabrication shop.
This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control. (PIC) skid designed as ''V''. The ATP will be performed after the construction of the PIC skid in the fabrication shop.
This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''U''. The ATP will be performed after the construction of the PIC skid in the fabrication shop.
This Acceptance Test Procedure (ATP) provides for the inspection and testing Of the new Pumping Instrumentation and Control (PIC) skid designed as ''T''. The ATP will be performed after the construction of the PIC skid in the fabrication shop.
This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''R''. The ATP will be performed after the construction of the PIC skid in the fabrication shop.
This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''Q''. The ATP will be performed after the construction of the PIC skid in the fabrication shop.
This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''P''. The ATP will be performed after the construction of the PIC skid in the fabrication shop.
This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designated as ''V''. The ATP will be performed after the construction of the PIC skid in the fabrication shop.
This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping and Instrumentation Control (PIC) skid designed as ''L''. The ATP will be performed after the construction of the PIC skid in the shop.
This Acceptance Test Procedure (ATP) provides for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designated as ''T''. The ATP will be performed after the construction of the PIC skid in the fabrication shop.
This ITOP (International Test Operations and Procedures) describes techniques and procedures for determining internal tube dimensions and other data of gun tubes development and acceptance testing.
This procedure will test the 17B MIT sensor inputs to the DACS trailer after installation of new thermocouple multiplexers and associated computer software.
Chassis Subsystem Functional Test Procedure PCN No. .... ASAS/ENSCE, Text Graphics Monitor Assembly Acceptance (functional) Test Procedure for ...
NASA Website
This document defines the acceptance criteria for the Automated Transportation Management System V2.0 Logistics Module Performance Based Incentive (PBI). This acceptance criteria will be the primary basis for the generation of acceptance test procedures. ...
This Acceptance Test Procedure (ATP) will document the satisfactory operation of the corrosion probe tree assembly. This ATP will be performed by the manufacturer prior to delivery to the site. The objective of this procedure is to demonstrate and document the acceptance of the corrosion probe ...
The TMACS Software Project Test Procedures translate the projects acceptance criteria into test steps. Software releases are certified when the affected Test Procedures are successfully performed and the customers authorize installation of these changes.
The Equipment Qualification Test described in this test procedure document is the acceptance test procedure (ATP) for the LDUA Baseline System. It verifies that the equipment is complete and in working order, and demonstrates its readiness for being deployed into an actual ...
This document describes The Performance Mock-up Test Procedure for the Valve Pit Leak Detection and Low Point Drain Assembly Performance Mock-Up Test Procedure.
This Acceptance Test Report (ATR) provides the test results for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''Q''. The ATR summaries the results and provides a copy of the ATP and inspections in the Appendix.
This Acceptance Test Report (ATR) provides the test results for the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''P''. The ATR summaries the results and provides a copy of the ATP and inspections in the Appendix.
This document establishes the procedure for performing the acceptance test on the two isolation barriers being installed in K West basin. This acceptance test procedure shall be used to: First establish a basin water loss rate prior to installation of the two isolation ...
This Acceptance Test Report (ATR) documents the results of WHC-SD-WM-ATP- 146 (Prototype Cone Penetrometer Moisture Probe Acceptance Test Procedure) and WHC-SD-WM-ATP-145 (Cone Penetrometer Moisture Probe Acceptance Test Procedure). ...
Simplified lateral nail tests and analytic aids used in this experiment gave acceptable predictions of wall racking strength for preliminary evaluations of wall construction. Racking strength evaluations to determine acceptability of new panel products cu...
This Factory Acceptance Test Procedure (FAT) is for the Westinghouse 100 Ton Hydraulic Trailer. The trailer will be used for the removal of the 101-SY pump. This procedure includes: safety check and safety procedures; pre-operation check out; startup; leveling trailer; functional/proofload ...
This document provides the Acceptance Test Report for the successful testing of the Safety Shutdown Circuit. The test was done in accordance with the requirements that were defined in WHC-SD-WM-SCH-003, Interim Stabilization Safety Class Trip Circuit CGI Dedication Criteria. The actual test ...
This provides the procedures for the void fraction acceptance test software, Version 1.2. The void fraction instrument will collect data to calculate the amount of gas trapped in Tank 101-SY.
Provides the plan and procedures for the acceptance test of changes that result in Version 1.1 of void fraction software. The void fraction instrument measures gas by volume in waste storage tanks.
The purpose of this acceptance test procedure (ATP) is to demonstrate that the newly installed Supervisory Control and Data Acquisition (SCADA) computer system functions as intended by the design.
A toxicity procedure has been developed and proposed for use in establishing acceptable initial loading rates and detoxification potentials for hazardous industrial waste when combined with soil. Screening test results are used to establish a range of loading rates acceptable for...
EPA Science Inventory
This Acceptance/Operational Test Procedure will document the satisfactory operation of the 105-AN Camera Purge Control System and 105-AN Video Camera System.
This Acceptance/Operational Test Procedure will document the satisfactory operation of the 105-AN Camera Purge Control System and 105-AN Video Camera System
This Acceptance/Operational Test Procedure will document the satisfactory operation of the 104-AN Camera Purge Control System and 104-AN Video Camera System.
This Acceptance/Operational Test Procedure will document the satisfactory operation of the 104-AN Camera Purge Control System and 104-AN Video Camera System
This Acceptance/Operational Test Procedure will document the satisfactory operation of the 103-AN Camera Purge Control System and 103-AN Video Camera System.
This Acceptance/Operational Test Procedure will document the satisfactory operation of the 103-AN Camera Purge Control System and 103-AN Video Camera System
This Acceptance/Operational Test Procedure will document the satisfactory operation of the 101-SY color camera purge control system and color camera video imaging system.
This document provides an Acceptance Test Procedure (ATP) for the project W-337 upgrades to the 340-NT-EX stack, and its associated sampling and monitoring systems.
This Acceptance Test Procedure for Project W-030 Cathodic Protection Installation, 241-AY and 241-AZ Tank Farm Ventilation Upgrade, has been prepared to demonstrate that the cathodic protection system functions as required by project criteria.
o Lot acceptance test per Ensign Bickford Procedure ATP 0030/2 ... Ensign Bickford Acceptance Test Procedure ATP 0030/2 (PETN-Cord) or ATP 0030/5 (HMX- Cord) ...
...shall meet scientifically accepted procedures. An example of a scientifically accepted procedure is outlined in the Manual on Sensory Testing Methods, ASTM Special Technical Publication 434, published by the American Society for Testing and...
Code of Federal Regulations, 2011
... for Desensitized Wax for use in US Navy explosives. Descriptors : *EXPLOSIVES, *QUALIFICATIONS, *WAXES, *DESENSITIZING, ACCEPTANCE ...
... Each beam describes radio frequency emission parameters and (optionally ... model radar systems that involve frequent activation and deactivation of ...
The author explains what is tested under the Cooling Tower Institute's (CTI) acceptance test procedure. The purpose of the CTI test code is to set standards for acceptance of cooling tower performance. It can be done by an independent consultant or a company can ...
This document describes the test results for the Revision 11.1 changes tested in the Acceptance Test Procedure on the Tank Monitor and Control System (TMACS).
This document is an executive summary of the testing, adjusting and balancing completed for Project W-112 for the HVAC systems. The actual results are document in the Acceptance Test Report.
This ATP establishes field testing procedures to demonstrate that the electrical/instrumentation system functions as intended by design for the Radioactive Mixed Waste Land Disposal Facility. Procedures are outlined for the field testing of the following:...
This document establishes the procedure for performing the acceptance test on the two isolation barriers being installed in K East basin. This acceptance test procedure shall be used to : First establish a basin water loss rate prior to installation of th...
This Acceptance Test Procedure is for the 241-SY-101 Flexible Receiver System, Phase III Testing. This procedure will test the sealing integrity of the Flexible Receiver System to ensure that release of waste and aerosols will be minimized during the removal of the ...
This Acceptance Test Procedure has been prepared to demonstrate that the Fire Protection System functions as required by project criteria. The test results will be issued as an acceptance test report after all the testing is complete. This facility is ...
... Results of Tests MATS Transponder S/N 3 ... SATELLITES), DISTANCE MEASURING EQUIPMENT, TEST METHODS, ACCEPTABILITY, RELIABILITY ...
Approach &. Generate. Accept Test Plan. Develop Test. Procedures. Dry Run. Test ..... Detailed approach documented in 6A Transition Plan. First Draft : April 28, ...
... Type I, data The objective of these procedures is to reduce the labor requirements of the currently used manual quality assurance (QA) procedures. ...
The purpose of this procedure is to document the Westronic Data units function as intended as installed at 241-AP-271 tank farm.
The purpose of this acceptance test procedure is to verify that the mechanical and electrical features of the Surface Moisture Measurement System are operating as designed and that the unit is ready for field service. This procedure will be used in conjunction with a software acceptance ...
This acceptance Test Procedure (ATP) has been prepared to demonstrate that modifications to the Fir Protection systems function as required by project criteria. The ATP will test the Fire Alarm Control Panels, Flow Alarm Pressure Switch, Heat Detectors, S...
This Acceptance Test Procedure (ATP) will document compliance with the requirements of WHC-S-056 Rev. 2 and ECN 608798. The equipment being tested is a Furniture Type trailer with storage cabinets, lighting and HVAC systems installed. The unit was purchas...
This Acceptance Test Procedure (ATP) will document compliance with the requirements of specification WHC-S-056 Rev.2 including ECNs 608798 and 616386. The equipment being tested is a furniture type trailer with storage cabinets, lighting and HVAC systems ...
This Acceptance Test Procedure (ATP) will test and verify that the Exhauster meets the specified functional requirements, safety requirements, operating requirements, and provide a record of the functional test results. The system/functions that will be t...
The overall objective of the acceptance test is to demonstrate a combined system. This includes associated tools and equipment necessary to perform cleaning in the 105 K East Basin (KE) for achieving optimum reduction in the level of contamination/dose rate on canisters prior to removal from the KE Basin and subsequent packaging for disposal. ...
Describes the Qualification test procedure for the AZ-101 Mixer Pump Data Acquisition System (DAS). The purpose of this Qualification Test Procedure (QTP) is to confirm that the AZ-101 Mixer Pump System has been properly programmed and hardware configured correctly. This QTP will test the ...
This Acceptance Test Report documents the test results of test procedure WHC-SD-WM-ATP-135 `Acceptance Test Procedure for the 241-AN- 274 Caustic Pump Control Building.` The objective of the test was to verify ...
The purpose of this Specific Test and Evaluation Plan (STEP) is to provide a detailed written plan for the systematic testing of modifications made to the 241-AX-B Valve Pit by the W-314 Project. The STEP develops the outline for test procedures that verify the system`s performance to the established Project design ...
For quite some time there has been no generally accepted procedure for field testing of large fans of the type commonly used to provide mechanical draft in fossil fired steam generating units. The Performance Test Code Committee Number 11 of the American Society of Mechanical Engineers has been working on the ...
This paper describes the cooldown and testing of the first yin-yang magnet for the Mirror Fusion Test Facility. The introduction describes the superconducting magnet; the rest of the paper explains the tests prior to and including magnet cooldown and final acceptance testing. The MFTF ...
The Corps of Engineers (CE) Test Procedures document has been prepared in a format similar to the referenced MIL-STD-705B test methods to provide for easy implementation by CE district and division personnel. The procedures provide for acceptance testing ...
... The modification at Raytheon concerns soldering procedures, engineering changeapproval, acceptance testing, configuration audits, annual test ...
DefenseLINK Web Site
... is accounted for during the Development Test and Evaluation (DT&E), Production Acceptance Test ... Air Traffic Rules and Procedures Service (ATP) ...
... concerns soldering procedures, engineering changeapproval, acceptance testing, configuration audits, annual test stationcertification, material ...
This acceptance test procedure shall be used to: First establish a basin water loss rate prior to installation of the two isolation barriers between the main basin and the discharge chute in K-Basin West. Second, perform an acceptance test to verify an ac...
...Acceptable Values for the Quantity A Defined in the Retroreflective Tire and Rim Test Procedure 3 Table 3 to Part 1512 Commercial...Acceptable Values for the Quantity A Defined in the Retroreflective Tire and Rim Test Procedure Observation angle (degrees)...
This is a Test Report for Acceptance Test Procedure (ATP) RPP-5489. This test report provides the results of the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''N''. The ATP was successfully ...
This is a Test Report for Acceptance Test Procedure (ATP) RPP-5073. This test report provides the results of the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''M''. The ATP was successfully ...
This is a Test Report for Acceptance Test Procedure (ATP) RPP-5055. This test report provides the results of the inspection and testing of the new Pumping Instrumentation and Control (PIC) skid designed as ''L''. The ATP was successfully ...
This publication summarizes building energy simulation test for existing homes (BESTEST-EX): instructions for implementing the test procedure, calibration tests reference results, and example acceptance-range criteria.
This Acceptance Test Procedure (ATP) will document compliance with the requirements of WHC-S-0249 Rev. 1 and ECN 606112. The equipment being tested is a Portable, Self-Contained Nitrogen Supply. The unit was purchased as a Design and Fabrication procurement activity. The Functional Test was ...
This Test Plan and Procedure outlines the methodology used to test the performance of several Hose-in-Hose Transfer Lines used by the River Protection Project's Interim Stabilization Group.
This Acceptance Test Procedure (ATP) has been prepared to demonstrate that the Fire Protection System functions as required by project criteria. The test results will be issued as an acceptance test report (ATR) after all testing is complete. Components ...
This Acceptance Test Report for the PUREX Surveillance and Monitoring and Control System (SAMCONS) Uninterruptible Power Supply (UPS) Acceptance Test Procedure validates the operation of the UPS, all alarming and display functions and the ability of the UPS to supply power to the SAMCONS as ...
... Acceptance Test Procedures (ATP) to be followed during the final test and evaluation of the FiAF (Finnish Air Force) Moving-Map Composer (MMC ...
This document details the Software Acceptance Testing of gas characterization systems. The gas characterization systems will be used to monitor the vapor spaces of waste tanks known to contain measurable concentrations of flammable gases.
This document details the field Acceptance Testing of a gas characterization system being installed on waste tank 241-AW-101. The gas characterization systems will be used to monitor the vapor spaces of waste tanks known to contain measurable concentrations of flammable gases.
This document details the field Acceptance Testing of a gas characterization system being installed on waste tank 241-AN-105. The gas characterization systems will be used to monitor the vapor spaces of waste tanks known to contain measurable concentrations of flammable gases.
Purpose of this ATP is to provide systematic acceptance testing of two rotary mode core sampling exhausters. These exhausters will support core sampling systems three and four. The exhaust gases are monitored for radionuclides, ammonia, and total organics...
This acceptance test verifies the MICON program changes for the new automatic transfer switch ATS-2 alarms, the Closed Loop Cooling isolator status, the CB-3 position alarm, and the alarms for the new emergency fan damper backup air compressor.
This supporting document provides detailed instruction for ensuring the existing alarms and interlocks are in an acceptable condition prior to performing the functional test of the AMS-4 installation.
...for Determining an Acceptable Exhaust Regeneration Durability-Data Test Schedule for...for Determining an Acceptable Exhaust Regeneration Durability-Data Test Schedule for...tested. Ns = Total number of regeneration emission tests. (Subscript...
This Acceptance Test Procedure (ATP) will document the satisfactory operation of the corrosion probe tree assembly destined for installation into tank 241-AN-105. This ATP will be performed by the manufacturer prior to delivery to the site. The objective of this procedure is to demonstrate and document the ...
Testing was started on February 24, 1998 and completed on February 25, 1998. The completed procedure consists of 4 acceptance test sections, 6.1 through 6.4. Three test exceptions were identified during the procedure. The first test exception was ...
The following Acceptance Test Procedure was written to test the ENRAF series 854 ATG with SPU II card prior to installation in the Tank Farms. The procedure sets various parameters and verifies the gauge and alarms functionality.
This Acceptance Test Report (ATR) documents the results of WHC-SD-WM-ATP-146 (Prototype Cone Penetrometer Moisture Probe Acceptance Test Procedure) and WHC-SD-WM-ATP-145 (Cone Penetrometer Moisture Probe Acceptance Test Procedure). ...
The TMACS Software Test Procedures translate the project`s acceptance criteria into test steps. The TMACS Test Plan (WHC-SD-WM-TP-148) is fulfilled when all Test Cases are approved. This Test Procedure tests the ...
This document defines the acceptance criteria for the Automated Transportation Management System V2.0 Logistics Module Performance Based Incentive (PBI). This acceptance criteria will be the primary basis for the generation of acceptance test procedures. The purpose of this document is to ...
... Examples of these procedures are: Melting point (including hot-stage microscopy), solid state IR, X- ray powder diffraction, thermal analysis procedures (like ...
Center for Drug Evaluation (CDER)
This test procedure specifies instructions for acceptance testing of software for exhaust fan control under Project ESPT (Energy Savings Performance Contract). The software controls the operation of two emergency exhaust fans when there is a power failure. This report details the results of ...
This report provides the completed copy and test results of the Acceptance Test Procedure (TWR-4713). Test results were actually hand written in the ATP including redline changes. All acceptance criteria steps were completed satisfactorily without exceptions.
In June 28, 1997, the Low Level Waste (LLW) glovebox was tested using glovebox acceptance test procedure 13031A-85. The primary focus of the glovebox acceptance test was to examine control system interlocks, display menus, alarms, and operator messages. L...
This document comprises the Acceptance Test Report for the 241-AZ-101 Ultrasonic Interface Level Analyzer. This document presents the results of Acceptance Testing of the 241-AZ-101 Ultrasonic Interface Level Analyzers (URSILLAs). Testing of the URSILLAs was performed in accordance with ...
This procedure provides acceptance testing for Enraf Series 854 level gauges used to monitor levels in Hanford Waste Storage Tanks. The test will verify that the gauge functions according to the manufacturer's instructions and specifications and is properly setup prior to being delivered to the tank farm ...
This Acceptance Test Procedure (ATP) will document compliance with the requirements of WHC-S-0252 Rev. 1 and ECNs 609271, and 609272. The equipment being tested is a 150KW Diesel Generator mounted on a trailer with switchgear. The unit was purchased as a Design and Fabrication procurement activity. The ATP was ...
The readiness of the Data Acquisition and Control System (DACS) to provide monitoring and control of the Programmable Logic Controller (PLC) abort coils from the Master and RSS stations will be systematically tested during performance of this procedure. I...
This ECN incorporates a complete procedure revision for testing the re-installation of a temporary Data Logger which is to be installed in support of upcoming mixer pump excavation runs.
This report describes the procedure to be used for acceptance testing of the Cone Penetrometer Moisture Probe (CPMP) system. The system includes the probe and detectors, the winch system, the NIM bin electronics, the thermistor, the laptop computer, Input/Output (I/O) interfaces, LabVIEW` application with automatic scanning features ...
This report primarily consists of the original test procedure used for the Operability Testing of the flammable gas modifications to Core Sample Truck No. One. Included are exceptions, resolutions, comments, and test results. This report consists of the original, completed, test ...
A search was made for test methods for the chemical resistance of membrane liners (geomembranes). Disclosed methods and procedures were examined and compared. Two tests being promoted for general acceptance are NSF Standard No. 54 (a voluntary industry-generated test) and the pro...
Tests to be performed for qualifying the payload development support system image motion compensator (IMC) are identified. The performance of these tests will verify the IMC interfaces and thereby verify the qualification test software.
A test is presented for compliance with Subpart 164.015. Specification for Plastic Foam, Unicellular, Buoyant, Sheet and Molded Shape. The foam tested was Type A sheet form. A description is given of the test procedures used and the results of the individ...
The purpose of this Acceptance Test Report is to provide documentation for the acceptance testing of the rotary mode core sample trucks 3 and 4, designated as HO-68K-4600 and HO-68K-4647, respectively. This report conforms to the guidelines established in WHC-IP-1026, ``Engineering Practice Guidelines,`` Appendix ...
This document is used to validate Revision 13.0 of the Tank Monitor and Control System (TMACS) and verify it functions as intended by design.
This document is used to validate Revision 11.1 of the Tank Monitor and Control System (TMACS) and verify its functions as intended by design.
Feb 27, 2003 ... A review of the acceptance test procedure (ATP) and previous flight ..... a leak in the epoxy in the Torr seal around its vacuum gauge tube. ...
... 555 PRECISION DC VOLTAGE STANDARD 559 400-CYCLE OSCILLATOR 560 AC - DC CONVERTER 565 TRUCK, HAND, AUTONAVIGATOR ...
The purpose of the OSU-MERDC Hydraulic Specification Program is to develop industrially acceptable test procedures and requirement specifications relative to the performance of hydraulic components and systems to facilitate the military's 'buy commericial...
The purpose of the OSU-MERDC hydraulics specification program is to develop industrially acceptable test procedures and requirement specifications relative to the performance of hydraulic components and systems to facilitate the military's 'buy commercial...
... acceptable test signals for the evaluation and fault finding analysis of the Info Express Sonar Imaging and Data Acquisition (SIDA) system and, in ...
This Acceptance Test Procedure (ATP) has been prepared to demonstrate that the Electrical/Instrumentation systems for the BCE function as required by project criteria.
This document is prepared to demonstrate that the cathodic protection system functions as intended by the design.
... Corporate Author : LEAR SIEGLER INC GRAND RAPIDS MICH INSTRUMENT DIV. Personal Author(s) : Ramsey,JE. Report Date : 19 FEB 1967. ...
A testing procedure evaluated in the Gulf of Mexico indicates more accurately the downhole performance of acid additives. Acid treatments designed with this method can prevent facility upsets and increase the production from acidized wells. The current industry accepted API RP 42 testing ...
Three ''detonation tests'' and one ''burn test'' were performed on an AN can, Type AN 8024, containing PETN pellets. Test procedures were discussed with a representative of the Department of Transportation. The can contained all reactions and ...
The Solid State Radar Beacon Decoder (SSRBD) operational and integration test procedures are defined; they will be conducted at the FAA operational facilities. These procedures will be executed following the contractor site acceptance test. Each SSRBD test configuration is ...
NASA Astrophysics Data System (ADS)
Shop Test of the Gamma Cart System to be used in the AZ-101 Mixer Pump Demonstration Test. Tests hardware and software. This procedure involves testing the Instrumentation involved with the Gamma Cart System, local and remote, including: depth indicators, speed controls, interface to data ...
Shop test of the sludge mobilization cart system to be used in the AZ-101 Mixer Pump Demonstration Test Tests hardware and software. This procedure involves testing the Instrumentation involved with the Gamma Cart System, local and remote, including depth indicators, speed controls, interface ...
The purpose of this Acceptance Test Procedure (ATP) is to verify the operability of the three new furnaces as controlled by the new Honeywell Modular Automation System (MAS). The Honeywell MAS is being installed in PFP to control the three thermal stabilization furnaces in glovebox HA-211. The ATP provides instructions for ...
... Title : Moving-Map Composers System Version 3.4P Acceptance Test Procedures Developed for the Finnish Air Force. Descriptive ...
This Acceptance Test Procedure for the PUREX Surveillance and Monitoring and Control System (SAMCONS) Uninterruptible Power Supply (UPS) provides for testing and verifying the proper operation of the control panel alarms and trouble functions, the 6roper functioning of the AC inverter, ability of the battery supply ...
This procedure provides acceptance testing for Enraf Series 854 level gauges used to monitor levels in Hanford Waste Storage Tanks. The test will verify that the gauge functions according to the manufacturer`s instructions and specifications and is properly setup prior to being delivered to the tank farm area.
This Acceptance Test Procedure (ATP) verifies proper construction per the design drawings and tests for proper functioning of the Pumping and Instrumentation Control (PIC) skid ''M''. The Scope section lists the systems and functions to be checked. This ATP will be performed at ...
This Acceptance Test Procedure (ATP) verifies proper construction per the design drawings and tests for proper functioning of the Pumping Instrumentation and Control (PIC) skid ''V''. The scope section lists the systems and functions to be checked. This ATP will be performed at ...
This document contains the acceptance test procedure for the mechanical equipment and instrumentation installed per the L-070 Project. The specific system to be tested are the pump controls for the 3906 Lift Station and 350-A Lift Station. In addition, verification that signals are being received by the 300 Area ...
This Acceptance Test Procedure (ATP) will document compliance with the requirements of WHC-S-0251 Rev. 0 and ECNs 613530 and 606113. The equipment being tested is a Breathing Air Supply Trailer purchased as a Design and Fabrication procurement activity for use in the core sampling program. The ATP was written by ...
This Acceptance/Operational Test Procedure (ATP/OTP) will document the satisfactory operation of the camera purge panel, purge control panel, color camera system and associated control components destined for installation. The final acceptance of the complete system will be performed in the field. The purge panel ...
Project W-320 Acceptance Test Report for tank 241-C-106, 296-C-006 Ventilation System Acceptance Test Procedure (ATP) HNF-SD-W320-012, C-106 Tank Process Ventilation Test, was an in depth test of the 296-C-006 ventilation system and ventilation support ...
242-A Evaporator distributive control system upgrade to D/3 version 9.0-2 for year 2000 compliance. Testing was performed per test procedure HNF-3568. There were no unresolved exceptions. The system responded correctly to all testing and meets the requirements to operate the 242-A This report documents the ...
This report summarizes the work performed in designing, fabricating, and acceptance testing small-scale storable propellant tanks. The design incorporates full-scale missile tank features and typical weld stresses. Fabrication and test procedures are base...
This ITOP describes procedures for conducting tests to evaluate the performance of tank cannon and hydropneumatic recoil mechanisms. This ITOP does not cover production acceptance tests, cannon safety tests (See ITOP 3-2-829), or cannon accessories such a...
An evaluation test was conducted to obtain performance data and develop an acceptance test procedure for a small oil spill retrieval system requiring no more than two men for its deployment and operation. It was found that the use of a simple, floating gr...
This Test Plan provides a test method to dedicate the leak detection relays used on the new Pumping Instrumentation and Control (PIC) skids. The new skids are fabricated on-site. The leak detection system is a safety class system per the Authorization Basis.
...following circumstances: (1) Blood, urine, or other bodily substances are tested using generally accepted scientific and medical methods and standards. (2) Breath tests are administered by qualified personnel (§ 634.33)....
