Sample records for accident safety analysis

  1. Reactor Safety Gap Evaluation of Accident Tolerant Components and Severe Accident Analysis

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Farmer, Mitchell T.; Bunt, R.; Corradini, M.

    The overall objective of this study was to conduct a technology gap evaluation on accident tolerant components and severe accident analysis methodologies with the goal of identifying any data and/or knowledge gaps that may exist, given the current state of light water reactor (LWR) severe accident research, and additionally augmented by insights obtained from the Fukushima accident. The ultimate benefit of this activity is that the results can be used to refine the Department of Energy’s (DOE) Reactor Safety Technology (RST) research and development (R&D) program plan to address key knowledge gaps in severe accident phenomena and analyses that affectmore » reactor safety and that are not currently being addressed by the industry or the Nuclear Regulatory Commission (NRC).« less

  2. Analysis on Dangerous Source of Large Safety Accident in Storage Tank Area

    NASA Astrophysics Data System (ADS)

    Wang, Tong; Li, Ying; Xie, Tiansheng; Liu, Yu; Zhu, Xueyuan

    2018-01-01

    The difference between a large safety accident and a general accident is that the consequences of a large safety accident are particularly serious. To study the tank area which factors directly or indirectly lead to the occurrence of large-sized safety accidents. According to the three kinds of hazard source theory and the consequence cause analysis of the super safety accident, this paper analyzes the dangerous source of the super safety accident in the tank area from four aspects, such as energy source, large-sized safety accident reason, management missing, environmental impact Based on the analysis of three kinds of hazard sources and environmental analysis to derive the main risk factors and the AHP evaluation model is established, and after rigorous and scientific calculation, the weights of the related factors in four kinds of risk factors and each type of risk factors are obtained. The result of analytic hierarchy process shows that management reasons is the most important one, and then the environmental factors and the direct cause and Energy source. It should be noted that although the direct cause is relatively low overall importance, the direct cause of Failure of emergency measures and Failure of prevention and control facilities in greater weight.

  3. Worker safety and injury severity analysis of earthmoving equipment accidents.

    PubMed

    Kazan, Emrah; Usmen, Mumtaz A

    2018-06-01

    Research on construction worker safety associated with construction equipment has mostly focused on accident type rather than injury severity and the embedded factor relationships. Significant variables and their effects on the degree of injury are examined for earthmoving equipment using data from OSHA. Four types of equipment, backhoe, bulldozer, excavator, and scraper are included in the study. Accidents involving on-foot workers and equipment operators are investigated collectively, as well as separately. Cross tabulation analysis was conducted to establish the associations between selected categorical variables, using degree of injury as a dichotomous dependent variable (fatal vs. nonfatal) and a number of independent variables having different values. Odds ratios were calculated to determine how much a certain variable/factor increases the odds of fatality in an accident, and the odds ratios were ranked to determine the relative impact of a given factor. It was found that twelve variables were significantly associated with injury severity. Rankings based on odds ratios showed that inadequate safety training (2.54), missing equipment protective system (2.38), being a non-union worker (2.26), being an equipment operator (1.93), and being on or around inadequately maintained equipment (1.58) produced higher odds for fatality. A majority of the earthmoving equipment accidents resulted in fatality. Backhoes were the most common equipment involved in accidents and fatalities. Struck-by accidents were the most prevalent and most fatal. Non-OSHA compliant safety training, missing seatbelt, operator not using seatbelt, malfunctioning back-up alarms, and poorly maintained equipment were factors contributing to accidents and fatalities. On-foot workers experienced a higher number of accidents than operators, while fatality odds were higher for the operators. Practical applications: Safety professionals should benefit from our findings in planning and delivering training

  4. Analysis of National Major Work Safety Accidents in China, 2003–2012

    PubMed Central

    YE, Yunfeng; ZHANG, Siheng; RAO, Jiaming; WANG, Haiqing; LI, Yang; WANG, Shengyong; DONG, Xiaomei

    2016-01-01

    Background: This study provides a national profile of major work safety accidents in China, which cause more than 10 fatalities per accident, intended to provide scientific basis for prevention measures and strategies to reduce major work safety accidents and deaths. Methods: Data from 2003–2012 Census of major work safety accidents were collected from State Administration of Work Safety System (SAWS). Published literature and statistical yearbook were also included to implement information. We analyzed the frequency of accidents and deaths, trend, geographic distribution and injury types. Additionally, we discussed the severity and urgency of emergency rescue by types of accidents. Results: A total of 877 major work safety accidents were reported, resulting in 16,795 deaths and 9,183 injuries. The numbers of accidents and deaths, mortality rate and incidence of major accidents have declined in recent years. The mortality rate and incidence was 0.71 and 1.20 per 106 populations in 2012, respectively. Transportation and mining contributed to the highest number of major accidents and deaths. Major aviation and railway accidents caused more casualties per incident, while collapse, machinery, electrical shock accidents and tailing dam accidents were the most severe situation that resulted in bigger proportion of death. Conclusion: Ten years’ major work safety accident data indicate that the frequency of accidents and number of eaths was declined and several safety concerns persist in some segments. PMID:27057515

  5. Analysis of occupational accidents: prevention through the use of additional technical safety measures for machinery.

    PubMed

    Dźwiarek, Marek; Latała, Agata

    2016-01-01

    This article presents an analysis of results of 1035 serious and 341 minor accidents recorded by Poland's National Labour Inspectorate (PIP) in 2005-2011, in view of their prevention by means of additional safety measures applied by machinery users. Since the analysis aimed at formulating principles for the application of technical safety measures, the analysed accidents should bear additional attributes: the type of machine operation, technical safety measures and the type of events causing injuries. The analysis proved that the executed tasks and injury-causing events were closely connected and there was a relation between casualty events and technical safety measures. In the case of tasks consisting of manual feeding and collecting materials, the injuries usually occur because of the rotating motion of tools or crushing due to a closing motion. Numerous accidents also happened in the course of supporting actions, like removing pollutants, correcting material position, cleaning, etc.

  6. Analysis of occupational accidents: prevention through the use of additional technical safety measures for machinery

    PubMed Central

    Dźwiarek, Marek; Latała, Agata

    2016-01-01

    This article presents an analysis of results of 1035 serious and 341 minor accidents recorded by Poland's National Labour Inspectorate (PIP) in 2005–2011, in view of their prevention by means of additional safety measures applied by machinery users. Since the analysis aimed at formulating principles for the application of technical safety measures, the analysed accidents should bear additional attributes: the type of machine operation, technical safety measures and the type of events causing injuries. The analysis proved that the executed tasks and injury-causing events were closely connected and there was a relation between casualty events and technical safety measures. In the case of tasks consisting of manual feeding and collecting materials, the injuries usually occur because of the rotating motion of tools or crushing due to a closing motion. Numerous accidents also happened in the course of supporting actions, like removing pollutants, correcting material position, cleaning, etc. PMID:26652689

  7. Circuit board accident--organizational dimension hidden by prescribed safety.

    PubMed

    de Almeida, Ildeberto Muniz; Buoso, Eduardo; do Amaral Dias, Maria Dionísia; Vilela, Rodolfo Andrade Gouveia

    2012-01-01

    This study analyzes an accident in which two maintenance workers suffered severe burns while replacing a circuit breaker panel in a steel mill, following model of analysis and prevention of accidents (MAPA) developed with the objective of enlarging the perimeter of interventions and contributing to deconstruction of blame attribution practices. The study was based on materials produced by a health service team in an in-depth analysis of the accident. The analysis shows that decisions related to system modernization were taken without considering their implications in maintenance scheduling and creating conflicts of priorities and of interests between production and safety; and also reveals that the lack of a systemic perspective in safety management was its principal failure. To explain the accident as merely non-fulfillment of idealized formal safety rules feeds practices of blame attribution supported by alibi norms and inhibits possible prevention. In contrast, accident analyses undertaken in worker health surveillance services show potential to reveal origins of these events incubated in the history of the system ignored in practices guided by the traditional paradigm.

  8. Meta-analysis of the effect of road safety campaigns on accidents.

    PubMed

    Phillips, Ross Owen; Ulleberg, Pål; Vaa, Truls

    2011-05-01

    A meta-analysis of 67 studies evaluating the effect of road safety campaigns on accidents is reported. A total of 119 results were extracted from the studies, which were reported in 12 different countries between 1975 and 2007. After allowing for publication bias and heterogeneity of effects, the weighted average effect of road safety campaigns is a 9% reduction in accidents (with 95% confidence that the weighted average is between -12 and -6%). To account for the variability of effects measured across studies, data were collected to characterise aspects of the campaign and evaluation design associated with each effect, and analysed to identify a model of seven campaign factors for testing by meta-regression. The model was tested using both fixed and random effect meta-regression, and dependency among effects was accounted for by aggregation. These analyses suggest positive associations between accident reduction and the use of personal communication or roadside media as part of a campaign delivery strategy. Campaigns with a drink-driving theme were also associated with greater accident reductions, while some of the analyses suggested that accompanying enforcement and short campaign duration (less than one month) are beneficial. Overall the results are consistent with the idea that campaigns can be more effective in the short term if the message is delivered with personal communication in a way that is proximal in space and time to the behaviour targeted by the campaign. Copyright © 2011 Elsevier Ltd. All rights reserved.

  9. [Implementation of safety devices: biological accident prevention].

    PubMed

    Catalán Gómez, M Teresa; Sol Vidiella, Josep; Castellà Castellà, Manel; Castells Bo, Carolina; Losada Pla, Nuria; Espuny, Javier Lluís

    2010-04-01

    Accidental exposures to blood and biological material were the most frequent and potentially serious accidents in healthcare workers, reported in the Prevention of Occupational Risks Unit within 2002. Evaluate the biological percutaneous accidents decrease after a progressive introduction of safety devices. Biological accidents produced between 2.002 and 2.006 were analyzed and reported by the injured healthcare workers to the Level 2b Hospital Prevention of Occupational Risk Unit with 238 beds and 750 employees. The key of the study was the safety devices (peripheral i.v. catheter, needleless i.v. access device and capillary blood collection lancet). Within 2002, 54 percutaneous biological accidents were registered and 19 in 2006, that represents a 64.8% decreased. There has been no safety devices accident reported involving these material. Accidents registered during the implantation period occurred because safety devices were not used at that time. Safety devices have proven to be effective in reducing needle stick percutaneous accidents, so that they are a good choice in the primary prevention of biological accidents contact.

  10. Canister Storage Building (CSB) Design Basis Accident Analysis Documentation

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    CROWE, R.D.; PIEPHO, M.G.

    2000-03-23

    This document provided the detailed accident analysis to support HNF-3553, Spent Nuclear Fuel Project Final Safety Analysis Report, Annex A, ''Canister Storage Building Final Safety Analysis Report''. All assumptions, parameters, and models used to provide the analysis of the design basis accidents are documented to support the conclusions in the Canister Storage Building Final Safety Analysis Report.

  11. Manned space flight nuclear system safety. Volume 3: Reactor system preliminary nuclear safety analysis. Part 2: Accident Model Document (AMD)

    NASA Technical Reports Server (NTRS)

    1972-01-01

    The Accident Model Document is one of three documents of the Preliminary Safety Analysis Report (PSAR) - Reactor System as applied to a Space Base Program. Potential terrestrial nuclear hazards involving the zirconium hydride reactor-Brayton power module are identified for all phases of the Space Base program. The accidents/events that give rise to the hazards are defined and abort sequence trees are developed to determine the sequence of events leading to the hazard and the associated probabilities of occurence. Source terms are calculated to determine the magnitude of the hazards. The above data is used in the mission accident analysis to determine the most probable and significant accidents/events in each mission phase. The only significant hazards during the prelaunch and launch ascent phases of the mission are those which arise form criticality accidents. Fission product inventories during this time period were found to be very low due to very limited low power acceptance testing.

  12. Single pilot IFR accident data analysis

    NASA Technical Reports Server (NTRS)

    Harris, D. F.

    1983-01-01

    The aircraft accident data recorded by the National Transportation and Safety Board (NTSR) for 1964-1979 were analyzed to determine what problems exist in the general aviation (GA) single pilot instrument flight rule (SPIFR) environment. A previous study conducted in 1978 for the years 1964-1975 provided a basis for comparison. This effort was generally limited to SPIFR pilot error landing phase accidents but includes some SPIFR takeoff and enroute accident analysis as well as some dual pilot IFR accident analysis for comparison. Analysis was performed for 554 accidents of which 39% (216) occurred during the years 1976-1979.

  13. SCAP: a new methodology for safety management based on feedback from credible accident-probabilistic fault tree analysis system.

    PubMed

    Khan, F I; Iqbal, A; Ramesh, N; Abbasi, S A

    2001-10-12

    As it is conventionally done, strategies for incorporating accident--prevention measures in any hazardous chemical process industry are developed on the basis of input from risk assessment. However, the two steps-- risk assessment and hazard reduction (or safety) measures--are not linked interactively in the existing methodologies. This prevents a quantitative assessment of the impacts of safety measures on risk control. We have made an attempt to develop a methodology in which risk assessment steps are interactively linked with implementation of safety measures. The resultant system tells us the extent of reduction of risk by each successive safety measure. It also tells based on sophisticated maximum credible accident analysis (MCAA) and probabilistic fault tree analysis (PFTA) whether a given unit can ever be made 'safe'. The application of the methodology has been illustrated with a case study.

  14. Categorizing accident sequences in the external radiotherapy for risk analysis

    PubMed Central

    2013-01-01

    Purpose This study identifies accident sequences from the past accidents in order to help the risk analysis application to the external radiotherapy. Materials and Methods This study reviews 59 accidental cases in two retrospective safety analyses that have collected the incidents in the external radiotherapy extensively. Two accident analysis reports that accumulated past incidents are investigated to identify accident sequences including initiating events, failure of safety measures, and consequences. This study classifies the accidents by the treatments stages and sources of errors for initiating events, types of failures in the safety measures, and types of undesirable consequences and the number of affected patients. Then, the accident sequences are grouped into several categories on the basis of similarity of progression. As a result, these cases can be categorized into 14 groups of accident sequence. Results The result indicates that risk analysis needs to pay attention to not only the planning stage, but also the calibration stage that is committed prior to the main treatment process. It also shows that human error is the largest contributor to initiating events as well as to the failure of safety measures. This study also illustrates an event tree analysis for an accident sequence initiated in the calibration. Conclusion This study is expected to provide sights into the accident sequences for the prospective risk analysis through the review of experiences. PMID:23865005

  15. Final safety analysis report for the Galileo Mission: Volume 2, Book 2: Accident model document: Appendices

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Not Available

    1988-12-15

    This section of the Accident Model Document (AMD) presents the appendices which describe the various analyses that have been conducted for use in the Galileo Final Safety Analysis Report II, Volume II. Included in these appendices are the approaches, techniques, conditions and assumptions used in the development of the analytical models plus the detailed results of the analyses. Also included in these appendices are summaries of the accidents and their associated probabilities and environment models taken from the Shuttle Data Book (NSTS-08116), plus summaries of the several segments of the recent GPHS safety test program. The information presented in thesemore » appendices is used in Section 3.0 of the AMD to develop the Failure/Abort Sequence Trees (FASTs) and to determine the fuel releases (source terms) resulting from the potential Space Shuttle/IUS accidents throughout the missions.« less

  16. BESAFE II: Accident safety analysis code for MFE reactor designs

    NASA Astrophysics Data System (ADS)

    Sevigny, Lawrence Michael

    The viability of controlled thermonuclear fusion as an alternative energy source hinges on its desirability from an economic and an environmental and safety standpoint. It is the latter which is the focus of this thesis. For magnetic fusion energy (MFE) devices, the safety concerns equate to a design's behavior during a worst-case accident scenario which is the loss of coolant accident (LOCA). In this dissertation, we examine the behavior of MFE devices during a LOCA and how this behavior relates to the safety characteristics of the machine; in particular the acute, whole-body, early dose. In doing so, we have produced an accident safety code, BESAFE II, now available to the fusion reactor design community. The Appendix constitutes the User's Manual for BESAFE II. The theory behind early dose calculations including the mobilization of activation products is presented in Chapter 2. Since mobilization of activation products is a strong function of temperature, it becomes necessary to calculate the thermal response of a design during a LOCA in order to determine the fraction of the activation products which are mobilized and thus become the source for the dose. The code BESAFE II is designed to determine the temperature history of each region of a design and determine the resulting mobilization of activation products at each point in time during the LOCA. The BESAFE II methodology is discussed in Chapter 4, followed by demonstrations of its use for two reference design cases: a PCA-Li tokamak and a SiC-He tokamak. Of these two cases, it is shown that the SiC-He tokamak is a better design from an accident safety standpoint than the PCA-Li tokamak. It is also found that doses derived from temperature-dependent mobilization data are different than those predicted using set mobilization categories such as those that involve Piet fractions. This demonstrates the need for more experimental data on fusion materials. The possibility for future improvements and modifications

  17. 50 CFR 401.17 - Safety and accident prevention.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 50 Wildlife and Fisheries 7 2010-10-01 2010-10-01 false Safety and accident prevention. 401.17... FISHERIES CONSERVATION, DEVELOPMENT AND ENHANCEMENT § 401.17 Safety and accident prevention. In the... governing safety, health and sanitation. ...

  18. Unions, Health and Safety Committees, and Workplace Accidents in the Korean Manufacturing Sector.

    PubMed

    Kim, Woo-Yung; Cho, Hm-Hak

    2016-06-01

    Despite the declining trend of workplace accidents in Republic of Korea, its level is still quite high compared with that in other developed countries. Factors that are responsible for high workplace accidents have not been well documented in Republic of Korea. The main purpose of this paper is to estimate the effects of unions and health and safety committees on workplace accidents in Korean manufacturing firms. We also allow for the interactions between unions and health and safety committees in the analysis. The results obtained in this paper will not only contribute to the literature in this field, but might also be useful for employers and worker representatives who are trying to find an effective way to reduce workplace accidents. This paper utilizes the 2012 Occupational Safety and Health Trend Survey data, which is a unique data set providing information on workplace injuries and illness as well as other characteristics of participatory firms, representative of the manufacturing industry in Republic of Korea. In estimating the effects of unions and health and safety committees, we build a negative binomial regression model in which the interactions between unions and health and safety committees are permissible in reducing workplace accidents. Health and safety committees were found to reduce the incidence of accidents whereas unionized establishments have higher incidence of accidents than nonunionized establishments. We also found that health and safety committees can more effectively reduce accidents in nonunionized establishments. By contrast, nonexclusive joint committees can more effectively reduce accidents in unionized establishments.

  19. Accident Journalism and Traffic Safety Education: A Three-Phase Investigation of Accident Reporting in the Canadian Daily Press.

    ERIC Educational Resources Information Center

    Wilde, Gerald J. S.; Ackersviller, Melody J.

    A study examined the potential for development of a traffic accident-reporting form in the Canadian daily press that strengthens concern for road safety in the general population and enhances knowledge, attitudes, and behavior leading to greater safety. The investigation was conducted on three levels: a content analysis, a readership analysis, and…

  20. Road accident rates: strategies and programmes for improving road traffic safety.

    PubMed

    Goniewicz, K; Goniewicz, M; Pawłowski, W; Fiedor, P

    2016-08-01

    Nowadays, the problem of road accident rates is one of the most important health and social policy issues concerning the countries in all continents. Each year, nearly 1.3 million people worldwide lose their life on roads, and 20-50 million sustain severe injuries, the majority of which require long-term treatment. The objective of the study was to identify the most frequent, constantly occurring causes of road accidents, as well as outline actions constituting a basis for the strategies and programmes aiming at improving traffic safety on local and global levels. Comparative analysis of literature concerning road safety was performed, confirming that although road accidents had a varied and frequently complex background, their causes have changed only to a small degree over the years. The causes include: lack of control and enforcement concerning implementation of traffic regulation (primarily driving at excessive speed, driving under the influence of alcohol, and not respecting the rights of other road users (mainly pedestrians and cyclists), lack of appropriate infrastructure and unroadworthy vehicles. The number of fatal accidents and severe injuries, resulting from road accidents, may be reduced through applying an integrated approach to safety on roads. The strategies and programmes for improving road traffic should include the following measures: reducing the risk of exposure to an accident, prevention of accidents, reduction in bodily injuries sustained in accidents, and reduction of the effects of injuries by improvement of post-accident medical care.

  1. Analysis of construction accidents in Spain, 2003-2008.

    PubMed

    López Arquillos, Antonio; Rubio Romero, Juan Carlos; Gibb, Alistair

    2012-12-01

    The research objective for this paper is to obtain a new extended and updated insight to the likely causes of construction accidents in Spain, in order to identify suitable mitigating actions. The paper analyzes all construction sector accidents in Spain between 2003 and 2008. Ten variables were chosen and the influence of each variable is evaluated with respect to the severity of the accident. The descriptive analysis is based on a total of 1,163,178 accidents. Results showed that the severity of accidents was related to variables including age, CNAE (National Classification of Economic Activities) code, size of company, length of service, location of accident, day of the week, days of absence, deviation, injury, and climatic zones. According to data analyzed, a large company is not always necessarily safer than a small company in the aspect of fatal accidents, experienced workers do not have the best accident fatality rates, and accidents occurring away from the usual workplace had more severe consequences. Results obtained in this paper can be used by companies in their occupational safety strategies, and in their safety training programs. Copyright © 2012 National Safety Council and Elsevier Ltd. All rights reserved.

  2. The relationship between safety climate and recent accidents: behavioral learning and cognitive attributions.

    PubMed

    Desai, Vinit M; Roberts, Karlene H; Ciavarelli, Anthony P

    2006-01-01

    The association between accidents and subsequent work unit safety perceptions was assessed to address cognitive and behavioral changes following accidents. Many studies attempt to predict accident rates using measures of work unit safety, but effects vary considerably. Conversely, this study examined whether recent accidents may be positively associated with work unit safety perceptions, as suggested by behavioral learning mechanisms (increases in safety investments following accidents) or cognitive mechanisms (defensive attributions regarding accident causality). Lagged squadron-level accident experience was correlated with work unit safety perceptions obtained through a 61-question safety climate survey administered to 6,361 individuals in U.S. Navy flight squadrons. Positive associations between minor or intermediately severe accidents and future safety climate scores were found, although no effect was found for major accidents. We suggest that accident history should be considered when examining work unit safety perceptions because recent accidents may be associated with higher safety climate scores. We did not find that this varies systematically with accident severity, and longitudinal research on additional samples is needed to further test this possibility. This research may be used to refine measurement of work unit safety and to examine impacts of accidents or safety violations on workers' cognitive processes and group behavioral changes.

  3. 50 CFR 401.17 - Safety and accident prevention.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 50 Wildlife and Fisheries 9 2011-10-01 2011-10-01 false Safety and accident prevention. 401.17 Section 401.17 Wildlife and Fisheries JOINT REGULATIONS (UNITED STATES FISH AND WILDLIFE SERVICE... FISHERIES CONSERVATION, DEVELOPMENT AND ENHANCEMENT § 401.17 Safety and accident prevention. In the...

  4. Identification of Behavior Based Safety by Using Traffic Light Analysis to Reduce Accidents

    NASA Astrophysics Data System (ADS)

    Mansur, A.; Nasution, M. I.

    2016-01-01

    This work present the safety assessment of a case study and describes an important area within the field production in oil and gas industry, namely behavior based safety (BBS). The company set a rigorous BBS and its intervention program that implemented and deployed continually. In this case, observers requested to have discussion and spread a number of determined questions related with work behavior to the workers during observation. Appraisal of Traffic Light Analysis (TLA) as one tools of risk assessment used to determine the estimated score of BBS questionnaire. Standardization of TLA appraisal in this study are based on Regulation of Minister of Labor and Occupational Safety and Health No:PER.05/MEN/1996. The result shown that there are some points under 84%, which categorized in yellow category and should corrected immediately by company to prevent existing bad behavior of workers. The application of BBS expected to increase the safety performance at work time-by-time and effective in reducing accidents.

  5. Why System Safety Professionals Should Read Accident Reports

    NASA Technical Reports Server (NTRS)

    Holloway, C. M.; Johnson, C. W.

    2006-01-01

    System safety professionals, both researchers and practitioners, who regularly read accident reports reap important benefits. These benefits include an improved ability to separate myths from reality, including both myths about specific accidents and ones concerning accidents in general; an increased understanding of the consequences of unlikely events, which can help inform future designs; a greater recognition of the limits of mathematical models; and guidance on potentially relevant research directions that may contribute to safety improvements in future systems.

  6. Prediction accident triangle in maintenance of underground mine facilities using Poisson distribution analysis

    NASA Astrophysics Data System (ADS)

    Khuluqi, M. H.; Prapdito, R. R.; Sambodo, F. P.

    2018-04-01

    In Indonesia, mining is categorized as a hazardous industry. In recent years, a dramatic increase of mining equipment and technological complexities had resulted in higher maintenance expectations that accompanied by the changes in the working conditions, especially on safety. Ensuring safety during the process of conducting maintenance works in underground mine is important as an integral part of accident prevention programs. Accident triangle has provided a support to safety practitioner to draw a road map in preventing accidents. Poisson distribution is appropriate for the analysis of accidents at a specific site in a given time period. Based on the analysis of accident statistics in the underground mine maintenance of PT. Freeport Indonesia from 2011 through 2016, it is found that 12 minor accidents for 1 major accident and 66 equipment damages for 1 major accident as a new value of accident triangle. The result can be used for the future need for improving the accident prevention programs.

  7. Indonesian Sea Accident Analysis (Case Study From 2003 – 2013)

    NASA Astrophysics Data System (ADS)

    Arya Dewanto, Y.; Faturachman, D.

    2018-03-01

    There are so many accidents in sea transportation in Indonesia. Most of the accidents happen because of low concern aspects of the safety and security of the crew. In sailing, a man as transport users to interact with the ship and the surrounding environment (including other ships, cruise lines, ports, and the situation of local conditions). These interactions are sometimes very complex and related to various aspects of. Aware of the multiplicity of aspects related to the third of these factors, seeking the safety of cruise through a reduction in the number of accidents and the risk of death and serious injuries due to accidents and goods transported is certainly not enough attempted through mono-sector approach, but rather takes a multi-sector approach to the efforts. In this paper, we described the Indonesian Sea Transportation accident analysis for eleven years divided into four items: total of ship accident type, ship accident factor, total of casualties, region of ship accidents. All data founded from Marine Court (Mahkamah Pelayaran). From that 4 items we can find Indonesia Sea Accident Analysis from 2003-2013.

  8. Alternative Fuels Data Center: Natural Gas Safety after a Traffic Accident

    Science.gov Websites

    Natural Gas Safety after a Traffic Accident to someone by E-mail Share Alternative Fuels Data Center: Natural Gas Safety after a Traffic Accident on Facebook Tweet about Alternative Fuels Data Center : Natural Gas Safety after a Traffic Accident on Twitter Bookmark Alternative Fuels Data Center: Natural Gas

  9. Is "Safety-in-numbers" theory applies to the pattern of pedestrian accidents in Seoul, South Korea.

    NASA Astrophysics Data System (ADS)

    Choi, Y.; Yoon, H.

    2016-12-01

    Every year, about 1.25 million people die of vehicle-related accidents, among which half are pedestrians with higher vulnerability: pedestrian, cyclists and motorcyclist (World Health Organization, 2016). This urges city governments in the world to strive for pedestrian safety and to apply diverse theories to transportation planning and design. The common belief is that the number of pedestrian accidents is directly and positively associated with the volume of pedestrian, however, another hypothesis, called "safety-in-numbers" effect, tells an opposite story in that accident rates declines with increase of the volume of pedestrian. In this study, we examine first, whether the safety-in-numbers theory applies to the pattern of pedestrian accidents in Seoul, and second, further investigate environmental factors that are associated with the pedestrian safety. On the first count, we use geospatial statistical analyses of the multi-year pedestrian accident data collected by Korea Road Traffic Authority (KoRoad) and the pedestrian volume data collected by SK Telecom (SKT). With Kernel Density Estimation and Bivariate Local Moran's I, we identify spatial clustering of pedestrian accidents in the city, and examine whether those locations match with concentrations of pedestrian volume. On the second count, we use statistical analysis, tobit, poisson and negative binomial regression to investigate relationships between pedestrian volume and number of pedestrian accident for the two types of geographic areas by the results of the aforementioned analysis; Area 1- locations of high volume of pedestrian with high number of accident, Area 2- locations of high volume of pedestrian with low number of accident. For environmental factors potentially explaining pedestrian accidents, we include land use composition, number of traffic lanes, crosswalk presence, pedestrian signal, traffic island and sidewalk width in our analysis. This research will be valuable in city governments

  10. Validity and consistency assessment of accident analysis methods in the petroleum industry.

    PubMed

    Ahmadi, Omran; Mortazavi, Seyed Bagher; Khavanin, Ali; Mokarami, Hamidreza

    2017-11-17

    Accident analysis is the main aspect of accident investigation. It includes the method of connecting different causes in a procedural way. Therefore, it is important to use valid and reliable methods for the investigation of different causal factors of accidents, especially the noteworthy ones. This study aimed to prominently assess the accuracy (sensitivity index [SI]) and consistency of the six most commonly used accident analysis methods in the petroleum industry. In order to evaluate the methods of accident analysis, two real case studies (process safety and personal accident) from the petroleum industry were analyzed by 10 assessors. The accuracy and consistency of these methods were then evaluated. The assessors were trained in the workshop of accident analysis methods. The systematic cause analysis technique and bowtie methods gained the greatest SI scores for both personal and process safety accidents, respectively. The best average results of the consistency in a single method (based on 10 independent assessors) were in the region of 70%. This study confirmed that the application of methods with pre-defined causes and a logic tree could enhance the sensitivity and consistency of accident analysis.

  11. Information Services at the Nuclear Safety Analysis Center.

    ERIC Educational Resources Information Center

    Simard, Ronald

    This paper describes the operations of the Nuclear Safety Analysis Center. Established soon after an accident at the Three Mile Island nuclear power plant near Harrisburg, Pennsylvania, its efforts were initially directed towards a detailed analysis of the accident. Continuing functions include: (1) the analysis of generic nuclear safety issues,…

  12. Single pilot IFR accident data analysis

    NASA Technical Reports Server (NTRS)

    Harris, D. F.; Morrisete, J. A.

    1982-01-01

    The aircraft accident data recorded and maintained by the National Transportation Safety Board for 1964 to 1979 were analyzed to determine what problems exist in the general aviation single pilot instrument flight rules environment. A previous study conducted in 1978 for the years 1964 to 1975 provided a basis for comparison. The purpose was to determine what changes, if any, have occurred in trends and cause-effect relationships reported in the earlier study. The increasing numbers have been tied to measures of activity to produce accident rates which in turn were analyzed in terms of change. Where anomalies or unusually high accident rates were encountered, further analysis was conducted to isolate pertinent patterns of cause factors and/or experience levels of involved pilots. The bulk of the effort addresses accidents in the landing phase of operations. A detailed analysis was performed on controlled/uncontrolled collisions and their unique attributes delineated. Estimates of day vs. night general aviation activity and accident rates were obtained.

  13. NASA Accident Precursor Analysis Handbook, Version 1.0

    NASA Technical Reports Server (NTRS)

    Groen, Frank; Everett, Chris; Hall, Anthony; Insley, Scott

    2011-01-01

    Catastrophic accidents are usually preceded by precursory events that, although observable, are not recognized as harbingers of a tragedy until after the fact. In the nuclear industry, the Three Mile Island accident was preceded by at least two events portending the potential for severe consequences from an underappreciated causal mechanism. Anomalies whose failure mechanisms were integral to the losses of Space Transportation Systems (STS) Challenger and Columbia had been occurring within the STS fleet prior to those accidents. Both the Rogers Commission Report and the Columbia Accident Investigation Board report found that processes in place at the time did not respond to the prior anomalies in a way that shed light on their true risk implications. This includes the concern that, in the words of the NASA Aerospace Safety Advisory Panel (ASAP), "no process addresses the need to update a hazard analysis when anomalies occur" At a broader level, the ASAP noted in 2007 that NASA "could better gauge the likelihood of losses by developing leading indicators, rather than continue to depend on lagging indicators". These observations suggest a need to revalidate prior assumptions and conclusions of existing safety (and reliability) analyses, as well as to consider the potential for previously unrecognized accident scenarios, when unexpected or otherwise undesired behaviors of the system are observed. This need is also discussed in NASA's system safety handbook, which advocates a view of safety assurance as driving a program to take steps that are necessary to establish and maintain a valid and credible argument for the safety of its missions. It is the premise of this handbook that making cases for safety more experience-based allows NASA to be better informed about the safety performance of its systems, and will ultimately help it to manage safety in a more effective manner. The APA process described in this handbook provides a systematic means of analyzing candidate

  14. Civil helicopter wire strike assessment study. Volume 2: Accident analysis briefs

    NASA Technical Reports Server (NTRS)

    Tuomela, C. H.; Brennan, M. F.

    1980-01-01

    A description and analysis of each of the 208 civil helicopter wire strike accidents reported to the National Transportation Safety Board (NTSB) for the ten year period 1970-1979 is given. The accident analysis briefs were based on pilot reports, FAA investigation reports, and such accident photographs as were made available. Briefs were grouped by year and, within year, by NTSB accident report number.

  15. Bus accident analysis of routes with/without bus priority.

    PubMed

    Goh, Kelvin Chun Keong; Currie, Graham; Sarvi, Majid; Logan, David

    2014-04-01

    This paper summarises findings on road safety performance and bus-involved accidents in Melbourne along roads where bus priority measures had been applied. Results from an empirical analysis of the accident types revealed significant reduction in the proportion of accidents involving buses hitting stationary objects and vehicles, which suggests the effect of bus priority in addressing manoeuvrability issues for buses. A mixed-effects negative binomial (MENB) regression and back-propagation neural network (BPNN) modelling of bus accidents considering wider influences on accident rates at a route section level also revealed significant safety benefits when bus priority is provided. Sensitivity analyses done on the BPNN model showed general agreement in the predicted accident frequency between both models. The slightly better performance recorded by the MENB model results suggests merits in adopting a mixed effects modelling approach for accident count prediction in practice given its capability to account for unobserved location and time-specific factors. A major implication of this research is that bus priority in Melbourne's context acts to improve road safety and should be a major consideration for road management agencies when implementing bus priority and road schemes. Copyright © 2013 Elsevier Ltd. All rights reserved.

  16. Road Safety Barriers, the Need and Influence on Road Traffic Accidents

    NASA Astrophysics Data System (ADS)

    Butāns, Ž.; Gross, K. A.; Gridnevs, A.; Karzubova, E.

    2015-11-01

    Constantly increasing intensity of road traffic and the allowed speed limits seem to impose stronger requirements on road infrastructure and use of road safety systems. One of the ways to improve road safety is the use of road restraint systems. Road safety barriers allow not only reducing the number of road traffic accidents, but also lowering the severity of accidents. The paper provides information on the technical requirements of road safety barriers. Various types of road safety barriers and their selection criteria for different types of road sections are discussed. The article views an example of a road traffic accident, which is also modelled by PC-Crash computer program. The given example reflects a road accident mechanism in case of a car-to-barrier collision, and provides information about the typical damage to the car and the barrier. The paper describes an impact of the road safety barrier type and its presence on the road traffic accident mechanism. Implementation and maintenance costs of different barrier types are viewed. The article presents a discussion on the necessity to use road safety barriers, as well as their optimal choice.

  17. Anthropotechnological analysis of industrial accidents in Brazil.

    PubMed Central

    Binder, M. C.; de Almeida, I. M.; Monteau, M.

    1999-01-01

    The Brazilian Ministry of Labour has been attempting to modify the norms used to analyse industrial accidents in the country. For this purpose, in 1994 it tried to make compulsory use of the causal tree approach to accident analysis, an approach developed in France during the 1970s, without having previously determined whether it is suitable for use under the industrial safety conditions that prevail in most Brazilian firms. In addition, opposition from Brazilian employers has blocked the proposed changes to the norms. The present study employed anthropotechnology to analyse experimental application of the causal tree method to work-related accidents in industrial firms in the region of Botucatu, São Paulo. Three work-related accidents were examined in three industrial firms representative of local, national and multinational companies. On the basis of the accidents analysed in this study, the rationale for the use of the causal tree method in Brazil can be summarized for each type of firm as follows: the method is redundant if there is a predominance of the type of risk whose elimination or neutralization requires adoption of conventional industrial safety measures (firm representative of local enterprises); the method is worth while if the company's specific technical risks have already largely been eliminated (firm representative of national enterprises); and the method is particularly appropriate if the firm has a good safety record and the causes of accidents are primarily related to industrial organization and management (multinational enterprise). PMID:10680249

  18. Organizational safety climate and supervisor safety enforcement: Multilevel explorations of the causes of accident underreporting.

    PubMed

    Probst, Tahira M

    2015-11-01

    According to national surveillance statistics, over 3 million employees are injured each year; yet, research indicates that these may be substantial underestimates of the true prevalence. The purpose of the current project was to empirically test the hypothesis that organizational safety climate and transactional supervisor safety leadership would predict the extent to which accidents go unreported by employees. Using hierarchical linear modeling and survey data collected from 1,238 employees in 33 organizations, employee-level supervisor safety enforcement behaviors (and to a less consistent extent, organizational-level safety climate) predicted employee accident underreporting. There was also a significant cross-level interaction, such that the effect of supervisor enforcement on underreporting was attenuated in organizations with a positive safety climate. These results may benefit human resources and safety professionals by pinpointing methods of increasing the accuracy of accident reporting, reducing actual safety incidents, and reducing the costs to individuals and organizations that result from underreporting. (c) 2015 APA, all rights reserved).

  19. Analysis of Child-related Road Traffic Accidents in Vietnam

    NASA Astrophysics Data System (ADS)

    Vu, Anh Tuan; Nguyen, Dinh Vinh Man

    2018-04-01

    In recent years, the number of road traffic accidents, fatalities and injuries have been decreasing, but the figures of children road traffic accidents have been increasing in Ho Chi Minh City of Vietnam. This fact strongly calls for implementing effective solutions to improve traffic safety for children by the local government. This paper presents the trends, patterns and causes of road traffic accidents involving children based on the analysis of road traffic accident data over the period 2010-2015 and the video-based observations of road traffic law violations at 15 typical school gates and 10 typical roads. The results could be useful for the city government to formulate solutions to effectively improve traffic safety for children in Ho Chi Minh City and other cities in Vietnam.

  20. Safety illusion and error trap in a collectively-operated machine accident.

    PubMed

    de Almeida, Ildeberto Muniz; Nobre, Hildeberto; do Amaral Dias, Maria Dionísia; Vilela, Rodolfo Andrade Gouveia

    2012-01-01

    Workplace accidents involving machines are relevant for their magnitude and their impacts on worker health. Despite consolidated critical statements, explanation centered on errors of operators remains predominant with industry professionals, hampering preventive measures and the improvement of production-system reliability. Several initiatives were adopted by enforcement agencies in partnership with universities to stimulate production and diffusion of analysis methodologies with a systemic approach. Starting from one accident case that occurred with a worker who operated a brake-clutch type mechanical press, the article explores cognitive aspects and the existence of traps in the operation of this machine. It deals with a large-sized press that, despite being endowed with a light curtain in areas of access to the pressing zone, did not meet legal requirements. The safety devices gave rise to an illusion of safety, permitting activation of the machine when a worker was still found within the operational zone. Preventive interventions must stimulate the tailoring of systems to the characteristics of workers, minimizing the creation of traps and encouraging safety policies and practices that replace judgments of behaviors that participate in accidents by analyses of reasons that lead workers to act in that manner.

  1. INDUSTRIAL/MILITARY ACTIVITY-INITIATED ACCIDENT SCREENING ANALYSIS

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    D.A. Kalinich

    1999-09-27

    Impacts due to nearby installations and operations were determined in the Preliminary MGDS Hazards Analysis (CRWMS M&O 1996) to be potentially applicable to the proposed repository at Yucca Mountain. This determination was conservatively based on limited knowledge of the potential activities ongoing on or off the Nevada Test Site (NTS). It is intended that the Industrial/Military Activity-Initiated Accident Screening Analysis provided herein will meet the requirements of the ''Standard Review Plan for the Review of Safety Analysis Reports for Nuclear Power Plants'' (NRC 1987) in establishing whether this external event can be screened from further consideration or must be includedmore » as a design basis event (DBE) in the development of accident scenarios for the Monitored Geologic Repository (MGR). This analysis only considers issues related to preclosure radiological safety. Issues important to waste isolation as related to impact from nearby installations will be covered in the MGR performance assessment.« less

  2. Development of Database for Accident Analysis in Indian Mines

    NASA Astrophysics Data System (ADS)

    Tripathy, Debi Prasad; Guru Raghavendra Reddy, K.

    2016-10-01

    Mining is a hazardous industry and high accident rates associated with underground mining is a cause of deep concern. Technological developments notwithstanding, rate of fatal accidents and reportable incidents have not shown corresponding levels of decline. This paper argues that adoption of appropriate safety standards by both mine management and the government may result in appreciable reduction in accident frequency. This can be achieved by using the technology in improving the working conditions, sensitising workers and managers about causes and prevention of accidents. Inputs required for a detailed analysis of an accident include information on location, time, type, cost of accident, victim, nature of injury, personal and environmental factors etc. Such information can be generated from data available in the standard coded accident report form. This paper presents a web based application for accident analysis in Indian mines during 2001-2013. An accident database (SafeStat) prototype based on Intranet of the TCP/IP agreement, as developed by the authors, is also discussed.

  3. Requirements Analysis for the Army Safety Management Information System (ASMIS)

    DTIC Science & Technology

    1989-03-01

    8217_>’ Telephone Number « .. PNL-6819 Limited Distribution Requirements Analysis for the Army Safety Management Information System (ASMIS) Final...PNL-6819 REQUIREMENTS ANALYSIS FOR THE ARMY SAFETY MANAGEMENT INFORMATION SYSTEM (ASMIS) FINAL REPORT J. S. Littlefield A. L. Corrigan March...accidents. This accident data is available under the Army Safety Management Information System (ASMIS) which is an umbrella for many databases

  4. Child Safety: It's No Accident. An Issue Statement.

    ERIC Educational Resources Information Center

    Virginia State Div. for Children, Richmond.

    The three major causes of injury and mortality among children in the state of Virginia are, in order of frequency, automobile-related accidents, poison ingestion, and suicide. With respect to injuries sustained in automobile accidents, adults traveling with children by car must accept responsibility for the safety of child passengers. Acute…

  5. Accidents at work and costs analysis: a field study in a large Italian company.

    PubMed

    Battaglia, Massimo; Frey, Marco; Passetti, Emilio

    2014-01-01

    Accidents at work are still a heavy burden in social and economic terms, and action to improve health and safety standards at work offers great potential gains not only to employers, but also to individuals and society as a whole. However, companies often are not interested to measure the costs of accidents even if cost information may facilitate preventive occupational health and safety management initiatives. The field study, carried out in a large Italian company, illustrates technical and organisational aspects associated with the implementation of an accident costs analysis tool. The results indicate that the implementation (and the use) of the tool requires a considerable commitment by the company, that accident costs analysis should serve to reinforce the importance of health and safety prevention and that the economic dimension of accidents is substantial. The study also suggests practical ways to facilitate the implementation and the moral acceptance of the accounting technology.

  6. The relationships between OHS prevention costs, safety performance, employee satisfaction and accident costs.

    PubMed

    Bayram, Metin; Ünğan, Mustafa C; Ardıç, Kadir

    2017-06-01

    Little is known about the costs of safety. A literature review conducted for this study indicates there is a lack of survey-based research dealing with the effects of occupational health and safety (OHS) prevention costs. To close this gap in the literature, this study investigates the interwoven relationships between OHS prevention costs, employee satisfaction, OHS performance and accident costs. Data were collected from 159 OHS management system 18001-certified firms operating in Turkey and analyzed through structural equation modeling. The findings indicate that OHS prevention costs have a significant positive effect on safety performance, employee satisfaction and accident costs savings; employee satisfaction has a significant positive effect on accident costs savings; and occupational safety performance has a significant positive effect on employee satisfaction and accident costs savings. Also, the results indicate that safety performance and employee satisfaction leverage the relationship between prevention costs and accident costs.

  7. Willingness to use safety belt and levels of injury in car accidents.

    PubMed

    de Lapparent, Matthieu

    2008-05-01

    In this article, we develop a bivariate ordered Probit model to analyze the decision to fasten the safety belt in a car and the resulting severity of accidents if it happens. The approach takes into account the fact that the decision to fasten the safety belt has a direct causal effect on the category of injury if an accident happens. Our application to a sample drawn from the database of French accident reports in 2003 for three populations of car users (drivers, front passengers, rear passengers) shows that fastening the safety belt is significantly related to a decrease in severe injuries but it shows also that these car users compensate partly for this safety benefit. Furthermore, it is observed that demographic characteristics of car users, as well as transport facilities, play important roles in decisions to fasten safety belts and in the eventual resulting accident injuries.

  8. Scenario analysis of freight vehicle accident risks in Taiwan.

    PubMed

    Tsai, Ming-Chih; Su, Chien-Chih

    2004-07-01

    This study develops a quantitative risk model by utilizing Generalized Linear Interactive Model (GLIM) to analyze the major freight vehicle accidents in Taiwan. Eight scenarios are established by interacting three categorical variables of driver ages, vehicle types and road types, each of which contains two levels. The database that consists of 2043 major accidents occurring between 1994 and 1998 in Taiwan is utilized to fit and calibrate the model parameters. The empirical results indicate that accident rates of freight vehicles in Taiwan were high in the scenarios involving trucks and non-freeway systems, while; accident consequences were severe in the scenarios involving mature drivers or non-freeway systems. Empirical evidences also show that there is no significant relationship between accident rates and accident consequences. This is to stress that safety studies that describe risk merely as accident rates rather than the combination of accident rates and consequences by definition might lead to biased risk perceptions. Finally, the study recommends using number of vehicle as an alternative of traffic exposure in commercial vehicle risk analysis. The merits of this would be that it is simple and thus reliable; meanwhile, the resulted risk that is termed as fatalities per vehicle could provide clear and direct policy implications for insurance practices and safety regulations.

  9. Vessel traffic safety in busy waterways: A case study of accidents in western shenzhen port.

    PubMed

    Mou, J M; Chen, P F; He, Y X; Yip, Tsz Leung; Li, W H; Tang, J; Zhang, H Z

    2016-08-03

    Throughout the world, busy waterways near large ports witness heavy vessel traffic in recent decades. The waterways are characterized by high risk in terms of loss of life, property, and pollution to environment. To facilitate maritime safety management with satisfactory efficiency and efficacy, the authors propose a framework of safety indexes to evaluate the risk level in busy waterways according to the accident severity, fatality rate and special indicators of maritime transportation. The safety indexes consist of Safety Evaluation Index (SEI) and Safety Warning Index (SWI), and are derived from the proposed risk criteria of Chinese vessel traffic. As a case study, data on vessel traffic accidents reported in the Western Shenzhen Port, South China from 1995 to 2015 are analyzed. The actual risk level of this area during the period is calculated under the framework. The implementation of the safety indexes indicate that the risk criteria and safety indexes are practicable and effective for the vessel traffic management. The methodology based on long-term accident data can significantly support the risk analysis in the macroscopic perspective for busy ports and waterways, such that SWI can act as threshold to trigger actions, while SEI can act as an indicator to measure safety status. Copyright © 2016 Elsevier Ltd. All rights reserved.

  10. Major accident prevention through applying safety knowledge management approach.

    PubMed

    Kalatpour, Omid

    2016-01-01

    Many scattered resources of knowledge are available to use for chemical accident prevention purposes. The common approach to management process safety, including using databases and referring to the available knowledge has some drawbacks. The main goal of this article was to devise a new emerged knowledge base (KB) for the chemical accident prevention domain. The scattered sources of safety knowledge were identified and scanned. Then, the collected knowledge was formalized through a computerized program. The Protégé software was used to formalize and represent the stored safety knowledge. The domain knowledge retrieved as well as data and information. This optimized approach improved safety and health knowledge management (KM) process and resolved some typical problems in the KM process. Upgrading the traditional resources of safety databases into the KBs can improve the interaction between the users and knowledge repository.

  11. Accidents at Work and Costs Analysis: A Field Study in a Large Italian Company

    PubMed Central

    BATTAGLIA, Massimo; FREY, Marco; PASSETTI, Emilio

    2014-01-01

    Accidents at work are still a heavy burden in social and economic terms, and action to improve health and safety standards at work offers great potential gains not only to employers, but also to individuals and society as a whole. However, companies often are not interested to measure the costs of accidents even if cost information may facilitate preventive occupational health and safety management initiatives. The field study, carried out in a large Italian company, illustrates technical and organisational aspects associated with the implementation of an accident costs analysis tool. The results indicate that the implementation (and the use) of the tool requires a considerable commitment by the company, that accident costs analysis should serve to reinforce the importance of health and safety prevention and that the economic dimension of accidents is substantial. The study also suggests practical ways to facilitate the implementation and the moral acceptance of the accounting technology. PMID:24869894

  12. Final safety analysis report for the Galileo Mission: Volume 2: Book 1, Accident model document

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Not Available

    The Accident Model Document (AMD) is the second volume of the three volume Final Safety Analysis Report (FSAR) for the Galileo outer planetary space science mission. This mission employs Radioisotope Thermoelectric Generators (RTGs) as the prime electrical power sources for the spacecraft. Galileo will be launched into Earth orbit using the Space Shuttle and will use the Inertial Upper Stage (IUS) booster to place the spacecraft into an Earth escape trajectory. The RTG's employ silicon-germanium thermoelectric couples to produce electricity from the heat energy that results from the decay of the radioisotope fuel, Plutonium-238, used in the RTG heat source.more » The heat source configuration used in the RTG's is termed General Purpose Heat Source (GPHS), and the RTG's are designated GPHS-RTGs. The use of radioactive material in these missions necessitates evaluations of the radiological risks that may be encountered by launch complex personnel as well as by the Earth's general population resulting from postulated malfunctions or failures occurring in the mission operations. The FSAR presents the results of a rigorous safety assessment, including substantial analyses and testing, of the launch and deployment of the RTGs for the Galileo mission. This AMD is a summary of the potential accident and failure sequences which might result in fuel release, the analysis and testing methods employed, and the predicted source terms. Each source term consists of a quantity of fuel released, the location of release and the physical characteristics of the fuel released. Each source term has an associated probability of occurrence. 27 figs., 11 tabs.« less

  13. Management system of health and safety work (SMK3) with job safety analysis (JSA) in PT. Nira Murni construction

    NASA Astrophysics Data System (ADS)

    Melliana, Armen, Yusrizal, Akmal, Syarifah

    2017-11-01

    PT Nira Murni construction is a contractor of PT Chevron Pacific Indonesia which engaged in contractor, fabrication, maintenance construction suppliers, and labor services. The high of accident rate in this company is caused the lack of awareness of workplace safety. Therefore, it requires an effort to reduce the accident rate on the company so that the financial losses can be minimized. In this study, Safe T-Score method is used to analyze the accident rate by measuring the level of frequency. Analysis is continued using risk management methods which identify hazards, risk measurement and risk management. The last analysis uses Job safety analysis (JSA) which will identify the effect of accidents. From the result of this study can be concluded that Job Safety Analysis (JSA) methods has not been implemented properly. Therefore, JSA method needs to follow-up in the next study, so that can be well applied as prevention of occupational accidents.

  14. 14 CFR 91.1021 - Internal safety reporting and incident/accident response.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    .../accident response. 91.1021 Section 91.1021 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... incident/accident response. (a) Each program manager must establish an internal anonymous safety reporting.... (b) Each program manager must establish procedures to respond to an aviation incident/accident. ...

  15. 78 FR 14877 - Pipeline Safety: Incident and Accident Reports

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-03-07

    ... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration [Docket ID PHMSA-2013-0028] Pipeline Safety: Incident and Accident Reports AGENCY: Pipeline and Hazardous Materials... PHMSA F 7100.2--Incident Report--Natural and Other Gas Transmission and Gathering Pipeline Systems and...

  16. Analysis of traffic accidents in Romania, 2009.

    PubMed

    Călinoiu, Geovana; Minca, Dana Galieta; Furtunescu, Florentina Ligia

    2012-01-01

    This paper aimed to underline the main consequences of traffic accidents in Romania 2009 and their associated causes or circumstances. We identified some problematic geographic areas, some critical months or moments of the day and also the most frequent causes; all these should become targets for the future planning. The current analysis provides some priority criteria for public health interventions. So, the future national road safety strategy should be in line with the EU objectives, but also with the national priorities. Romania is far away from the average EU target for 2010 of halving the death by traffic accidents registered in 2001. To describe the circumstances and the consequences related to traffic accidents registered in Romania, for the year 2009. An ecological study was conducted. The traffic accidents circumstances were analyzed in terms of magnitude, geographic space, time and cause. The consequences were analyzed as affected people and damaged cars. A total of 28,627 traffic accidents were registered in Romania during the year 2009. 2,796 people were killed and 27,968 were hospitalized and 42,443 cars were damaged. 3 of 4 accidents were caused by violations on behalf of the car drivers. Most common violations in car drivers were excess of speed and priority violations (52.4%). Among the pedestrians, 7 of 10 accidents were caused by illegal crossing. A higher number of accidents occurred during the summer months and during the evening hours (from 5.00 pm till 8.00 pm). The traffic accidents represent a real public health problem in Romania and a serious burden for the health system. The gap between Romania and the other EU member states needs to be diminished in the next decade. In this purpose, the future national road safety strategy should be in line with the EU objectives, but also with the national priorities. Research is needed to understand the causes and the socio-economical impact of traffic accidents and to define appropriate national

  17. A cluster analysis on road traffic accidents using genetic algorithms

    NASA Astrophysics Data System (ADS)

    Saharan, Sabariah; Baragona, Roberto

    2017-04-01

    The analysis of traffic road accidents is increasingly important because of the accidents cost and public road safety. The availability or large data sets makes the study of factors that affect the frequency and severity accidents are viable. However, the data are often highly unbalanced and overlapped. We deal with the data set of the road traffic accidents recorded in Christchurch, New Zealand, from 2000-2009 with a total of 26440 accidents. The data is in a binary set and there are 50 factors road traffic accidents with four level of severity. We used genetic algorithm for the analysis because we are in the presence of a large unbalanced data set and standard clustering like k-means algorithm may not be suitable for the task. The genetic algorithm based on clustering for unknown K, (GCUK) has been used to identify the factors associated with accidents of different levels of severity. The results provided us with an interesting insight into the relationship between factors and accidents severity level and suggest that the two main factors that contributes to fatal accidents are "Speed greater than 60 km h" and "Did not see other people until it was too late". A comparison with the k-means algorithm and the independent component analysis is performed to validate the results.

  18. Challenging the immediate causes: A work accident investigation in an oil refinery using organizational analysis.

    PubMed

    Beltran, Sandra Lorena; Vilela, Rodolfo Andrade de Gouveia; de Almeida, Ildeberto Muniz

    2018-01-01

    In many companies, investigations of accidents still blame the victims without exploring deeper causes. Those investigations are reactive and have no learning potential. This paper aims to debate the historical organizational aspects of a company whose policy was incubating an accident. The empirical data are analyzed as part of a qualitative study of an accident that occurred in an oil refinery in Brazil in 2014. To investigate and analyse this case we used one-to-one and group interviews, participant observation, Collective Analyses of Work and a documentary review. The analysis was conducted on the basis of concepts of the Organizational Analysis of the event and the Model for Analysis and Prevention of Work Accidents. The accident had its origin in the interaction of social and organizational factors, among them being: excessively standardized culture, management tools and outcome indicators that give a false sense of safety, the decision to speed up the project, the change of operator to facilitate this outcome and performance management that encourages getting around the usual barriers. The superficial accident analysis conducted by the company that ignored human and organizational factors reinforces the traditional safety culture and favors the occurrence of new accidents.

  19. Control of Industrial Safety Based on Dynamic Characteristics of a Safety Budget-Industrial Accident Rate Model in Republic of Korea.

    PubMed

    Choi, Gi Heung; Loh, Byoung Gook

    2017-06-01

    Despite the recent efforts to prevent industrial accidents in the Republic of Korea, the industrial accident rate has not improved much. Industrial safety policies and safety management are also known to be inefficient. This study focused on dynamic characteristics of industrial safety systems and their effects on safety performance in the Republic of Korea. Such dynamic characteristics are particularly important for restructuring of the industrial safety system. The effects of damping and elastic characteristics of the industrial safety system model on safety performance were examined and feedback control performance was explained in view of cost and benefit. The implications on safety policies of restructuring the industrial safety system were also explored. A strong correlation between the safety budget and the industrial accident rate enabled modeling of an industrial safety system with these variables as the input and the output, respectively. A more effective and efficient industrial safety system could be realized by having weaker elastic characteristics and stronger damping characteristics in it. A substantial decrease in total social cost is expected as the industrial safety system is restructured accordingly. A simple feedback control with proportional-integral action is effective in prevention of industrial accidents. Securing a lower level of elastic industrial accident-driving energy appears to have dominant effects on the control performance compared with the damping effort to dissipate such energy. More attention needs to be directed towards physical and social feedbacks that have prolonged cumulative effects. Suggestions for further improvement of the safety system including physical and social feedbacks are also made.

  20. Design and implementation of an identification system in construction site safety for proactive accident prevention.

    PubMed

    Yang, Huanjia; Chew, David A S; Wu, Weiwei; Zhou, Zhipeng; Li, Qiming

    2012-09-01

    Identifying accident precursors using real-time identity information has great potential to improve safety performance in construction industry, which is still suffering from day to day records of accident fatality and injury. Based on the requirements analysis for identifying precursor and the discussion of enabling technology solutions for acquiring and sharing real-time automatic identification information on construction site, this paper proposes an identification system design for proactive accident prevention to improve construction site safety. Firstly, a case study is conducted to analyze the automatic identification requirements for identifying accident precursors in construction site. Results show that it mainly consists of three aspects, namely access control, training and inspection information and operation authority. The system is then designed to fulfill these requirements based on ZigBee enabled wireless sensor network (WSN), radio frequency identification (RFID) technology and an integrated ZigBee RFID sensor network structure. At the same time, an information database is also designed and implemented, which includes 15 tables, 54 queries and several reports and forms. In the end, a demonstration system based on the proposed system design is developed as a proof of concept prototype. The contributions of this study include the requirement analysis and technical design of a real-time identity information tracking solution for proactive accident prevention on construction sites. The technical solution proposed in this paper has a significant importance in improving safety performance on construction sites. Moreover, this study can serve as a reference design for future system integrations where more functions, such as environment monitoring and location tracking, can be added. Copyright © 2011 Elsevier Ltd. All rights reserved.

  1. Home Safety, Safe Behaviors of Elderly People, and Fall Accidents At Home

    ERIC Educational Resources Information Center

    Erkal, Sibel

    2010-01-01

    The present study analyzed home safety and safe behaviors against fall accidents of elderly people living at home. The study group comprised 121 people aged 65+ living in the catchment area of Ankara Mamak Halil Ulgen Health Center. Data were collected via a personal information form and Home-Screen Scale. Statistical analysis used an independent…

  2. Job safety analysis and hazard identification for work accident prevention in para rubber wood sawmills in southern Thailand.

    PubMed

    Thepaksorn, Phayong; Thongjerm, Supawan; Incharoen, Salee; Siriwong, Wattasit; Harada, Kouji; Koizumi, Akio

    2017-11-25

    We utilized job safety analysis (JSA) and hazard identification for work accident prevention in Para rubber wood sawmills, which aimed to investigate occupational health risk exposures and assess the health hazards at sawmills in the Trang Province, located in southern Thailand. We conducted a cross-sectional study which included a walk-through survey, JSA, occupational risk assessment, and environmental samplings from March through September 2015 at four Para rubber wood sawmills. We identified potential occupational safety and health hazards associated with six main processes, including: 1) logging and cutting, 2) sawing the lumber into sheets, 3) planing and re-arranging, 4) vacuuming and wood preservation, 5) drying and planks re-arranging, and 6) grading, packing, and storing. Working in sawmills was associated with high risk of wood dust and noise exposure, occupational accidents injuring hands and feet, chemicals and fungicide exposure, and injury due to poor ergonomics or repetitive work. Several high-risk areas were identified from JSA and hazard identification of the working processes, especially high wood dust and noise exposure when sawing lumber into sheets and risk of occupational accidents of the hands and feet when struck by lumber. All workers were strongly recommended to use personal protective equipment in any working processes. Exposures should be controlled using local ventilation systems and reducing noise transmission. We recommend that the results from the risk assessment performed in this study be used to create an action plan for reducing occupational health hazards in Para rubber sawmills.

  3. ADAM: An Accident Diagnostic,Analysis and Management System - Applications to Severe Accident Simulation and Management

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Zavisca, M.J.; Khatib-Rahbar, M.; Esmaili, H.

    2002-07-01

    The Accident Diagnostic, Analysis and Management (ADAM) computer code has been developed as a tool for on-line applications to accident diagnostics, simulation, management and training. ADAM's severe accident simulation capabilities incorporate a balance of mechanistic, phenomenologically based models with simple parametric approaches for elements including (but not limited to) thermal hydraulics; heat transfer; fuel heatup, meltdown, and relocation; fission product release and transport; combustible gas generation and combustion; and core-concrete interaction. The overall model is defined by a relatively coarse spatial nodalization of the reactor coolant and containment systems and is advanced explicitly in time. The result is to enablemore » much faster than real time (i.e., 100 to 1000 times faster than real time on a personal computer) applications to on-line investigations and/or accident management training. Other features of the simulation module include provision for activation of water injection, including the Engineered Safety Features, as well as other mechanisms for the assessment of accident management and recovery strategies and the evaluation of PSA success criteria. The accident diagnostics module of ADAM uses on-line access to selected plant parameters (as measured by plant sensors) to compute the thermodynamic state of the plant, and to predict various margins to safety (e.g., times to pressure vessel saturation and steam generator dryout). Rule-based logic is employed to classify the measured data as belonging to one of a number of likely scenarios based on symptoms, and a number of 'alarms' are generated to signal the state of the reactor and containment. This paper will address the features and limitations of ADAM with particular focus on accident simulation and management. (authors)« less

  4. Safety regulations, firm size, and the risk of accidents in E&P operations on the Gulf of Mexico outer continental shelf

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Iledare, O.O.; Pulsipher, A.G.; Baumann, R.H.

    1996-12-31

    The current expanded role of smaller independent oil producers in the OCS has led to concern about the possibility of increased risk of accidents in E&P operations on the Gulf of Mexico OCS. In addition, questions have been posed concerning the effects of the Minerals Management Service`s (MMS) safety regulations and inspection program, firm size, and industry practices on the risk of accidents in E&P operations on the Gulf of Mexico OCS. The specific purposes of the study reported in this paper were to ascertain (1) whether any empirical justification exists for the widespread concern that an increase in independentsmore » relative share of E&P operations in the Gulf OCS region will be detrimental to safety, and (2) whether MMS policies and safety programs have reduced the frequency or severity of accidents on the OCS. Our statistical and descriptive analyses of data on accidents from MMS provide no statistical evidence to support the apprehension that an expanded role for independents in E&P activity constitutes any major threat to safety on the OCS. Further, the results of our econometrics analysis confirm the expectation that the more effective MMS inspectors are at detecting incidents of noncompliance the lower the rate of accidents on the OCS is, ceteris paribus. In addition the results indicate that the variability in platform exposure years--cumulative age of operating platform--in comparison to other factors explains a significant portion of the variation in accidents per operating platform. That is, the platform aging process provides more opportunity for accidents than any other contributing factors. Our econometrics analysis also suggests that, if the other factors contributing to offshore accidents are held constant, the responsiveness of accident rate to drilling activity is inelastic while the response of accident rate to production activity levels is elastic.« less

  5. An Analysis of U.S. Civil Rotorcraft Accidents by Cost and Injury (1990-1996)

    NASA Technical Reports Server (NTRS)

    Iseler, Laura; DeMaio, Joe; Rutkowski, Michael (Technical Monitor)

    2002-01-01

    A study of rotorcraft accidents was conducted to identify safety issues and research areas that might lead to a reduction in rotorcraft accidents and fatalities. The primary source of data was summaries of National Transportation Safety Board (NTSB) accident reports. From 1990 to 1996, the NTSB documented 1396 civil rotorcraft accidents in the United States in which 491 people were killed. The rotorcraft data were compared to airline and general aviation data to determine the relative safety of rotorcraft compared to other segments of the aviation industry. In depth analysis of the rotorcraft data addressed demographics, mission, and operational factors. Rotorcraft were found to have an accident rate about ten times that of commercial airliners and about the same as that of general aviation. The likelihood that an accident would be fatal was about equal for all three classes of operation. The most dramatic division in rotorcraft accidents is between flights flown by private pilots versus professional pilots. Private pilots, flying low cost aircraft in benign environments, have accidents that are due, in large part, to their own errors. Professional pilots, in contrast, are more likely to have accidents that are a result of exacting missions or use of specialized equipment. For both groups judgement error is more likely to lead to a fatal accident than are other types of causes. Several approaches to improving the rotorcraft accident rate are recommended. These mostly address improvement in the training of new pilots and improving the safety awareness of private pilots.

  6. Government regulation of occupational safety: underground coal mine accidents 1973-75.

    PubMed Central

    Boden, L I

    1985-01-01

    The purpose of this paper is to determine the influence of federal mine safety inspections on underground coal mine accidents. An economic incentives model is developed to relate federal enforcement activities to accident rates. The determinants of accident rates are analyzed for 535 coal mines during the period 1973-75. Estimates based on these data when applied to the model indicate that increasing inspections by 25 per cent would have produced a 13 per cent decline in fatal accidents and an 18 per cent decline in disabling accidents. PMID:3985237

  7. Government regulation of occupational safety: underground coal mine accidents 1973-75.

    PubMed

    Boden, L I

    1985-05-01

    The purpose of this paper is to determine the influence of federal mine safety inspections on underground coal mine accidents. An economic incentives model is developed to relate federal enforcement activities to accident rates. The determinants of accident rates are analyzed for 535 coal mines during the period 1973-75. Estimates based on these data when applied to the model indicate that increasing inspections by 25 per cent would have produced a 13 per cent decline in fatal accidents and an 18 per cent decline in disabling accidents.

  8. 10 CFR 70.62 - Safety program and integrated safety analysis.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ...; (iv) Potential accident sequences caused by process deviations or other events internal to the... of occurrence of each potential accident sequence identified pursuant to paragraph (c)(1)(iv) of this... have experience in nuclear criticality safety, radiation safety, fire safety, and chemical process...

  9. 10 CFR 70.62 - Safety program and integrated safety analysis.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ...; (iv) Potential accident sequences caused by process deviations or other events internal to the... of occurrence of each potential accident sequence identified pursuant to paragraph (c)(1)(iv) of this... have experience in nuclear criticality safety, radiation safety, fire safety, and chemical process...

  10. 10 CFR 70.62 - Safety program and integrated safety analysis.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ...; (iv) Potential accident sequences caused by process deviations or other events internal to the... of occurrence of each potential accident sequence identified pursuant to paragraph (c)(1)(iv) of this... have experience in nuclear criticality safety, radiation safety, fire safety, and chemical process...

  11. Young people and snowmobiling in northern Norway: accidents, injury prevention and safety strategies.

    PubMed

    Mehus, Grete; Mehus, Alf Gunnar; Germeten, Sidsel; Henriksen, Nils

    2016-01-01

    Snowmobiling among young people in Scandinavia frequently leads to accidents and injuries. Systematic studies of accidents exist, but few studies have addressed young drivers' experiences. The aim of this article is to reveal how young people experience and interpret accidents, and to outline a prevention strategy. Thirty-one girls and 50 boys aged 16-23 years from secondary schools in Northern Norway and on Svalbard, a Norwegian archipelago in the Arctic Ocean, participated in 17 focus groups segregated by gender. A content analysis identified themes addressing the research questions. Participants described risk as being inherent to snowmobiling, and claimed that accidents followed from poor risk assessment, careless driving or mishaps. Evaluation of accidents and recommendations for preventive measures varied. Girls acknowledged the risks and wanted knowledge about outdoor life, navigation and external risks. Boys underestimated or downplayed the risks, and wanted knowledge about safety precautions while freeriding. Both genders were aware of how and why accidents occurred, and took precautions. Boys tended to challenge norms in ways that contradict the promotion of safe driving behaviour. Stories of internal justice regarding driving under the influence of alcohol occurred. Adolescents are aware of how accidents occur and how to avoid them. Injury prevention strategies should include a general population strategy and a high-risk strategy targeted at extreme risk-seekers. Drivers, snowmobilers' organisations and the community should share local knowledge in an effort to define problem areas, set priorities and develop and implement preventive measures. Risk prevention should include preparation of safe tracks and focus on safety equipment and safe driving behaviour, but should also pay increased attention to the potential of strengthening normative regulation within peer groups regarding driving behaviour and mutual responsibility for preventing accidents.

  12. The Driver Behaviour Questionnaire as accident predictor; A methodological re-meta-analysis.

    PubMed

    Af Wåhlberg, A E; Barraclough, P; Freeman, J

    2015-12-01

    The Manchester Driver Behaviour Questionnaire (DBQ) is the most commonly used self-report tool in traffic safety research and applied settings. It has been claimed that the violation factor of this instrument predicts accident involvement, which was supported by a previous meta-analysis. However, that analysis did not test for methodological effects, or include unpublished results. The present study re-analysed studies on prediction of accident involvement from DBQ factors, including lapses, and many unpublished effects. Tests of various types of dissemination bias and common method variance were undertaken. Outlier analysis showed that some effects were probably not reliable data, but excluding them did not change the results. For correlations between violations and crashes, tendencies for published effects to be larger than unpublished ones and for effects to decrease over time were observed, but were not significant. Also, using the mean of accidents as proxy for effect indicated that studies where effects for violations are not reported have smaller effect sizes. These differences indicate dissemination bias. Studies using self-reported accidents as dependent variables had much larger effects than those using recorded accident data. Also, zero-order correlations were larger than partial correlations controlled for exposure. Similarly, violations/accidents effects were strong only when there was also a strong correlation between accidents and exposure. Overall, the true effect is probably very close to zero (r<.07) for violations versus traffic accident involvement, depending upon which tendencies are controlled for. Methodological factors and dissemination bias have inflated the published effect sizes of the DBQ. Strong evidence of various artefactual effects is apparent. A greater level of care should be taken if the DBQ continues to be used in traffic safety research. Also, validation of self-reports should be more comprehensive in the future, taking into

  13. KERENA safety concept in the context of the Fukushima accident

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Zacharias, T.; Novotny, C.; Bielor, E.

    Within the last three years AREVA NP and E.On KK finalized the basic design of KERENA which is a medium sized innovative boiling water reactor, based on the operational experience of German BWR nuclear power plants (NPPs). It is a generation III reactor design with a net electrical output of about 1250 MW. It combines active safety equipment of service-proven designs with new passive safety components, both safety classified. The passive systems utilize basic laws of physics, such as gravity and natural convection, enabling them to function without electric power. Even actuation of these systems is performed thanks to basicmore » physic laws. The degree of diversity in component and system design, achieved by combining active and passive equipment, results in a very low core damage frequency. The Fukushima accident enhanced the world wide discussion about the safety of operating nuclear power plants. World wide stress tests for operating nuclear power plants are being performed embracing both natural and man made hazards. Beside the assessment of existing power plants, also new designs are analyzed regarding the system response to beyond design base accidents. KERENA's optimal combination of diversified cooling systems (active and passive) allows passing efficiently such tests, with a high level of confidence. This paper describes the passive safety components and the KERENA reactor behavior after a Fukushima like accident. (authors)« less

  14. 14 CFR 91.1021 - Internal safety reporting and incident/accident response.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    .../accident response. 91.1021 Section 91.1021 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AIR TRAFFIC AND GENERAL OPERATING RULES GENERAL OPERATING AND FLIGHT... incident/accident response. (a) Each program manager must establish an internal anonymous safety reporting...

  15. Overview of Energy Systems` safety analysis report programs. Safety Analysis Report Update Program

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Not Available

    1992-03-01

    The primary purpose of an Safety Analysis Report (SAR) is to provide a basis for judging the adequacy of a facility`s safety. The SAR documents the safety analyses that systematically identify the hazards posed by the facility, analyze the consequences and risk of potential accidents, and describe hazard control measures that protect the health and safety of the public and employees. In addition, some SARs document, as Technical Safety Requirements (TSRs, which include Technical Specifications and Operational Safety Requirements), technical and administrative requirements that ensure the facility is operated within prescribed safety limits. SARs also provide conveniently summarized information thatmore » may be used to support procedure development, training, inspections, and other activities necessary to facility operation. This ``Overview of Energy Systems Safety Analysis Report Programs`` Provides an introduction to the programs and processes used in the development and maintenance of the SARs. It also summarizes some of the uses of the SARs within Energy Systems and DOE.« less

  16. 'Remixing Rasmussen': The evolution of Accimaps within systemic accident analysis.

    PubMed

    Waterson, Patrick; Jenkins, Daniel P; Salmon, Paul M; Underwood, Peter

    2017-03-01

    Throughout Jens Rasmussen's career there has been a continued emphasis on the development of methods, techniques and tools for accident analysis and investigation. In this paper we focus on the evolution and development of one specific example, namely Accimaps and their use for accident analysis. We describe the origins of Accimaps followed by a review of 27 studies which have applied and adapted Accimaps over the period 2000-2015 to a range of domains and types of accident. Aside from demonstrating the versatility and popularity of the method, part of the motivation for the review of the use of Accimaps is to address the question of what constitutes a sound, usable, valid and reliable approach to systemic accident analysis. The findings from the review demonstrate continuity with the work carried out by Rasmussen, as well as significant variation (e.g., changes to the Accimap, used of additional theoretical and practice-oriented perspectives on safety). We conclude the paper with some speculations regarding future extension and adaptation of the Accimap approach including the possibility of using hybrid models for accident analysis. Copyright © 2016 Elsevier Ltd. All rights reserved.

  17. One in a Million Given the Accident: Assuring Nuclear Weapon Safety

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Weaver, Jason

    2015-08-25

    Since the introduction of nuclear weapons, there has not been a single instance of accidental or unauthorized nuclear detonation, but there have been numerous accidents and “close calls.” As the understanding of these environments has increased, the need for a robust nuclear weapon safety philosophy has grown. This paper describes some of the methods used by the Nuclear Weapon Complex today to assure nuclear weapon safety, including testing, modeling, analysis, and design features. Lastly, it also reviews safety’s continued role in the future and examines how nuclear safety’s present maturity can play a role in strengthening security and other areasmore » and how increased coordination can improve safety and reduce long-term cost.« less

  18. Job safety analysis and hazard identification for work accident prevention in para rubber wood sawmills in southern Thailand

    PubMed Central

    Thepaksorn, Phayong; Thongjerm, Supawan; Incharoen, Salee; Siriwong, Wattasit; Harada, Kouji; Koizumi, Akio

    2017-01-01

    Objective: We utilized job safety analysis (JSA) and hazard identification for work accident prevention in Para rubber wood sawmills, which aimed to investigate occupational health risk exposures and assess the health hazards at sawmills in the Trang Province, located in southern Thailand. Methods: We conducted a cross-sectional study which included a walk-through survey, JSA, occupational risk assessment, and environmental samplings from March through September 2015 at four Para rubber wood sawmills. Results: We identified potential occupational safety and health hazards associated with six main processes, including: 1) logging and cutting, 2) sawing the lumber into sheets, 3) planing and re-arranging, 4) vacuuming and wood preservation, 5) drying and planks re-arranging, and 6) grading, packing, and storing. Working in sawmills was associated with high risk of wood dust and noise exposure, occupational accidents injuring hands and feet, chemicals and fungicide exposure, and injury due to poor ergonomics or repetitive work. Discussion: Several high-risk areas were identified from JSA and hazard identification of the working processes, especially high wood dust and noise exposure when sawing lumber into sheets and risk of occupational accidents of the hands and feet when struck by lumber. All workers were strongly recommended to use personal protective equipment in any working processes. Exposures should be controlled using local ventilation systems and reducing noise transmission. We recommend that the results from the risk assessment performed in this study be used to create an action plan for reducing occupational health hazards in Para rubber sawmills. PMID:28993571

  19. Human error and commercial aviation accidents: an analysis using the human factors analysis and classification system.

    PubMed

    Shappell, Scott; Detwiler, Cristy; Holcomb, Kali; Hackworth, Carla; Boquet, Albert; Wiegmann, Douglas A

    2007-04-01

    The aim of this study was to extend previous examinations of aviation accidents to include specific aircrew, environmental, supervisory, and organizational factors associated with two types of commercial aviation (air carrier and commuter/ on-demand) accidents using the Human Factors Analysis and Classification System (HFACS). HFACS is a theoretically based tool for investigating and analyzing human error associated with accidents and incidents. Previous research has shown that HFACS can be reliably used to identify human factors trends associated with military and general aviation accidents. Using data obtained from both the National Transportation Safety Board and the Federal Aviation Administration, 6 pilot-raters classified aircrew, supervisory, organizational, and environmental causal factors associated with 1020 commercial aviation accidents that occurred over a 13-year period. The majority of accident causal factors were attributed to aircrew and the environment, with decidedly fewer associated with supervisory and organizational causes. Comparisons were made between HFACS causal categories and traditional situational variables such as visual conditions, injury severity, and regional differences. These data will provide support for the continuation, modification, and/or development of interventions aimed at commercial aviation safety. HFACS provides a tool for assessing human factors associated with accidents and incidents.

  20. Work-related accidents among the Iranian population: a time series analysis, 2000-2011.

    PubMed

    Karimlou, Masoud; Salehi, Masoud; Imani, Mehdi; Hosseini, Agha-Fatemeh; Dehnad, Afsaneh; Vahabi, Nasim; Bakhtiyari, Mahmood

    2015-01-01

    Work-related accidents result in human suffering and economic losses and are considered as a major health problem worldwide, especially in the economically developing world. To introduce seasonal autoregressive moving average (ARIMA) models for time series analysis of work-related accident data for workers insured by the Iranian Social Security Organization (ISSO) between 2000 and 2011. In this retrospective study, all insured people experiencing at least one work-related accident during a 10-year period were included in the analyses. We used Box-Jenkins modeling to develop a time series model of the total number of accidents. There was an average of 1476 accidents per month (1476·05±458·77, mean±SD). The final ARIMA (p,d,q) (P,D,Q)s model for fitting to data was: ARIMA(1,1,1)×(0,1,1)12 consisting of the first ordering of the autoregressive, moving average and seasonal moving average parameters with 20·942 mean absolute percentage error (MAPE). The final model showed that time series analysis of ARIMA models was useful for forecasting the number of work-related accidents in Iran. In addition, the forecasted number of work-related accidents for 2011 explained the stability of occurrence of these accidents in recent years, indicating a need for preventive occupational health and safety policies such as safety inspection.

  1. Glider accidents: an analysis of 143 cases, 2001-2005.

    PubMed

    van Doorn, Robert R A; de Voogt, Alexander J

    2007-01-01

    The majority of aviation crashes and casualties take place in general and sport aviation. Although gliding has gained popularity in recent decades, we could find no systematic analysis of glider accidents. This study determined factors associated with both non-fatal and fatal glider accidents to document their position within sport and general aviation accidents, and to suggest preventive measures and improvements. We performed a retrospective review of glider accidents for the period 2001-2005 in the database maintained by the U.S. National Transportation Safety Board (NTSB). A total of 117 non-fatal and 26 fatal glider accidents were reported for the 5-yr period. Adverse weather was the cause in 20% of all non-fatal accidents, 60% of which occurred in the cruise phase. Logistic regression revealed that fatal accidents were predicted by pilot error, flight phase, and home-built aircraft. Factors contributing to glider crashes are specific to this type of sport aviation. Owners of home-built gliders should pay particular attention to the aircraft's specifications and design limits.

  2. Analysis of roadside inspection data and its relationship to accident and safety/compliance review data and reviews of previous and ongoing research in these areas

    DOT National Transportation Integrated Search

    1993-01-01

    The main objective of the present study is to analyze roadside inspection data and its relationship to safety/compliance review and accident data. Data used for this analysis is provided by the Office of Motor Carriers and includes a sample of larger...

  3. Assessing the safety effects of cooperative intelligent transport systems: A bowtie analysis approach.

    PubMed

    Ehlers, Ute Christine; Ryeng, Eirin Olaussen; McCormack, Edward; Khan, Faisal; Ehlers, Sören

    2017-02-01

    The safety effects of cooperative intelligent transport systems (C-ITS) are mostly unknown and associated with uncertainties, because these systems represent emerging technology. This study proposes a bowtie analysis as a conceptual framework for evaluating the safety effect of cooperative intelligent transport systems. These seek to prevent road traffic accidents or mitigate their consequences. Under the assumption of the potential occurrence of a particular single vehicle accident, three case studies demonstrate the application of the bowtie analysis approach in road traffic safety. The approach utilizes exemplary expert estimates and knowledge from literature on the probability of the occurrence of accident risk factors and of the success of safety measures. Fuzzy set theory is applied to handle uncertainty in expert knowledge. Based on this approach, a useful tool is developed to estimate the effects of safety-related cooperative intelligent transport systems in terms of the expected change in accident occurrence and consequence probability. Copyright © 2016 Elsevier Ltd. All rights reserved.

  4. Systems Analysis of NASA Aviation Safety Program: Final Report

    NASA Technical Reports Server (NTRS)

    Jones, Sharon M.; Reveley, Mary S.; Withrow, Colleen A.; Evans, Joni K.; Barr, Lawrence; Leone, Karen

    2013-01-01

    A three-month study (February to April 2010) of the NASA Aviation Safety (AvSafe) program was conducted. This study comprised three components: (1) a statistical analysis of currently available civilian subsonic aircraft data from the National Transportation Safety Board (NTSB), the Federal Aviation Administration (FAA), and the Aviation Safety Information Analysis and Sharing (ASIAS) system to identify any significant or overlooked aviation safety issues; (2) a high-level qualitative identification of future safety risks, with an assessment of the potential impact of the NASA AvSafe research on the National Airspace System (NAS) based on these risks; and (3) a detailed, top-down analysis of the NASA AvSafe program using an established and peer-reviewed systems analysis methodology. The statistical analysis identified the top aviation "tall poles" based on NTSB accident and FAA incident data from 1997 to 2006. A separate examination of medical helicopter accidents in the United States was also conducted. Multiple external sources were used to develop a compilation of ten "tall poles" in future safety issues/risks. The top-down analysis of the AvSafe was conducted by using a modification of the Gibson methodology. Of the 17 challenging safety issues that were identified, 11 were directly addressed by the AvSafe program research portfolio.

  5. The accident analysis of mobile mine machinery in Indian opencast coal mines.

    PubMed

    Kumar, R; Ghosh, A K

    2014-01-01

    This paper presents the analysis of large mining machinery related accidents in Indian opencast coal mines. The trends of coal production, share of mining methods in production, machinery deployment in open cast mines, size and population of machinery, accidents due to machinery, types and causes of accidents have been analysed from the year 1995 to 2008. The scrutiny of accidents during this period reveals that most of the responsible factors are machine reversal, haul road design, human fault, operator's fault, machine fault, visibility and dump design. Considering the types of machines, namely, dumpers, excavators, dozers and loaders together the maximum number of fatal accidents has been caused by operator's faults and human faults jointly during the period from 1995 to 2008. The novel finding of this analysis is that large machines with state-of-the-art safety system did not reduce the fatal accidents in Indian opencast coal mines.

  6. Influence of occupational safety management on the incidence rate of occupational accidents in the Spanish industrial and ornamental stone mining.

    PubMed

    Sanmiquel, Lluís; Rossell, Josep M; Vintró, Carla; Freijo, Modesto

    2014-01-01

    Mines are hazardous and workers can suffer many types of accidents caused by fire, flood, explosion or collapse. Injury incidence rates in mining are considerably higher than those registered by other economic sectors. One of the main reasons for this high-level incidence rate is the existence of a large number of dangerous workplaces. This work analyzes the influence that occupational safety management had on the accidents that took place in Spanish mining of industrial and ornamental stone during the period 2007-2008. Primary data sources are: (a) Results from a statistical study of the occupational health and safety management practices of 71 quarries defined by a questionnaire of 41 items; and (b) Occupational accidents registered in the Spanish industrial and ornamental stone mining throughout the period 2007-2008. The obtained results indicate that workplaces with a low average score in the analysis of occupational safety management have a higher incidence rate of accidents. Studies on mining workplaces are very important to help detect occupational safety concerns. Results from this study help raise awareness and will encourage the adoption of appropriate measures to improve safety.

  7. A system of safety management practices and worker engagement for reducing and preventing accidents: an empirical and theoretical investigation.

    PubMed

    Wachter, Jan K; Yorio, Patrick L

    2014-07-01

    The overall research objective was to theoretically and empirically develop the ideas around a system of safety management practices (ten practices were elaborated), to test their relationship with objective safety statistics (such as accident rates), and to explore how these practices work to achieve positive safety results (accident prevention) through worker engagement. Data were collected using safety manager, supervisor and employee surveys designed to assess and link safety management system practices, employee perceptions resulting from existing practices, and safety performance outcomes. Results indicate the following: there is a significant negative relationship between the presence of ten individual safety management practices, as well as the composite of these practices, with accident rates; there is a significant negative relationship between the level of safety-focused worker emotional and cognitive engagement with accident rates; safety management systems and worker engagement levels can be used individually to predict accident rates; safety management systems can be used to predict worker engagement levels; and worker engagement levels act as mediators between the safety management system and safety performance outcomes (such as accident rates). Even though the presence of safety management system practices is linked with incident reduction and may represent a necessary first-step in accident prevention, safety performance may also depend on mediation by safety-focused cognitive and emotional engagement by workers. Thus, when organizations invest in a safety management system approach to reducing/preventing accidents and improving safety performance, they should also be concerned about winning over the minds and hearts of their workers through human performance-based safety management systems designed to promote and enhance worker engagement. Copyright © 2013 The Authors. Published by Elsevier Ltd.. All rights reserved.

  8. Analysis of Two Electrocution Accidents in Greece that Occurred due to Unexpected Re-energization of Power Lines.

    PubMed

    Baka, Aikaterini D; Uzunoglu, Nikolaos K

    2014-09-01

    Investigation and analysis of accidents are critical elements of safety management. The over-riding purpose of an organization in carrying out an accident investigation is to prevent similar accidents, as well as seek a general improvement in the management of health and safety. Hundreds of workers have suffered injuries while installing, maintaining, or servicing machinery and equipment due to sudden re-energization of power lines. This study presents and analyzes two electrical accidents (1 fatal injury and 1 serious injury) that occurred because the power supply was reconnected inadvertently or by mistake.

  9. Analysis of Two Electrocution Accidents in Greece that Occurred due to Unexpected Re-energization of Power Lines

    PubMed Central

    Baka, Aikaterini D.; Uzunoglu, Nikolaos K.

    2014-01-01

    Investigation and analysis of accidents are critical elements of safety management. The over-riding purpose of an organization in carrying out an accident investigation is to prevent similar accidents, as well as seek a general improvement in the management of health and safety. Hundreds of workers have suffered injuries while installing, maintaining, or servicing machinery and equipment due to sudden re-energization of power lines. This study presents and analyzes two electrical accidents (1 fatal injury and 1 serious injury) that occurred because the power supply was reconnected inadvertently or by mistake. PMID:25379331

  10. Corporate cost of occupational accidents: an activity-based analysis.

    PubMed

    Rikhardsson, Pall M; Impgaard, Martin

    2004-03-01

    The systematic accident cost analysis (SACA) project was carried out during 2001 by The Aarhus School of Business and PricewaterhouseCoopers Denmark with financial support from The Danish National Working Environment Authority. Its focused on developing and testing a method for evaluating occupational costs of companies for use by occupational health and safety professionals. The method was tested in nine Danish companies within three different industry sectors and the costs of 27 selected occupational accidents in these companies were calculated. One of the main conclusions is that the SACA method could be used in all of the companies without revisions. The evaluation of accident cost showed that 2/3 of the costs of occupational accidents are visible in the Danish corporate accounting systems reviewed while 1/3 is hidden from management view. The highest cost of occupational accidents for a company with 3.600 employees was estimated to approximately US$ 682.000. The paper includes an introduction regarding accident cost analysis in companies, a presentation of the SACA project methodology and the SACA method itself, a short overview of some of the results of the SACA project and a conclusion. Further information about the project is available at http://www.asb.dk/saca.

  11. PROBABILISTIC SAFETY ASSESSMENT OF OPERATIONAL ACCIDENTS AT THE WASTE ISOLATION PILOT PLANT

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Rucker, D.F.

    2000-09-01

    This report presents a probabilistic safety assessment of radioactive doses as consequences from accident scenarios to complement the deterministic assessment presented in the Waste Isolation Pilot Plant (WIPP) Safety Analysis Report (SAR). The International Council of Radiation Protection (ICRP) recommends both assessments be conducted to ensure that ''an adequate level of safety has been achieved and that no major contributors to risk are overlooked'' (ICRP 1993). To that end, the probabilistic assessment for the WIPP accident scenarios addresses the wide range of assumptions, e.g. the range of values representing the radioactive source of an accident, that could possibly have beenmore » overlooked by the SAR. Routine releases of radionuclides from the WIPP repository to the environment during the waste emplacement operations are expected to be essentially zero. In contrast, potential accidental releases from postulated accident scenarios during waste handling and emplacement could be substantial, which necessitates the need for radiological air monitoring and confinement barriers (DOE 1999). The WIPP Safety Analysis Report (SAR) calculated doses from accidental releases to the on-site (at 100 m from the source) and off-site (at the Exclusive Use Boundary and Site Boundary) public by a deterministic approach. This approach, as demonstrated in the SAR, uses single-point values of key parameters to assess the 50-year, whole-body committed effective dose equivalent (CEDE). The basic assumptions used in the SAR to formulate the CEDE are retained for this report's probabilistic assessment. However, for the probabilistic assessment, single-point parameter values were replaced with probability density functions (PDF) and were sampled over an expected range. Monte Carlo simulations were run, in which 10,000 iterations were performed by randomly selecting one value for each parameter and calculating the dose. Statistical information was then derived from the 10

  12. Offsite radiological consequence analysis for the bounding flammable gas accident

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    CARRO, C.A.

    2003-03-19

    The purpose of this analysis is to calculate the offsite radiological consequence of the bounding flammable gas accident. DOE-STD-3009-94, ''Preparation Guide for U.S. Department of Energy Nonreactor Nuclear Facility Documented Safety Analyses'', requires the formal quantification of a limited subset of accidents representing a complete set of bounding conditions. The results of these analyses are then evaluated to determine if they challenge the DOE-STD-3009-94, Appendix A, ''Evaluation Guideline,'' of 25 rem total effective dose equivalent in order to identify and evaluate safety class structures, systems, and components. The bounding flammable gas accident is a detonation in a single-shell tank (SST).more » A detonation versus a deflagration was selected for analysis because the faster flame speed of a detonation can potentially result in a larger release of respirable material. As will be shown, the consequences of a detonation in either an SST or a double-shell tank (DST) are approximately equal. A detonation in an SST was selected as the bounding condition because the estimated respirable release masses are the same and because the doses per unit quantity of waste inhaled are generally greater for SSTs than for DSTs. Appendix A contains a DST analysis for comparison purposes.« less

  13. Manned space flight nuclear system safety. Volume 3: Reactor system preliminary nuclear safety analysis. Part 3: Nuclear Safety Analysis Document (NSAD)

    NASA Technical Reports Server (NTRS)

    1972-01-01

    Nuclear safety analysis as applied to a space base mission is presented. The nuclear safety analysis document summarizes the mission and the credible accidents/events which may lead to nuclear hazards to the general public. The radiological effects and associated consequences of the hazards are discussed in detail. The probability of occurrence is combined with the potential number of individuals exposed to or above guideline values to provide a measure of accident and total mission risk. The overall mission risk has been determined to be low with the potential exposure to or above 25 rem limited to less than 4 individuals per every 1000 missions performed. No radiological risk to the general public occurs during the prelaunch phase at KSC. The most significant risks occur from prolonged exposure to reactor debris following land impact generally associated with the disposal phase of the mission where fission product inventories can be high.

  14. Aviation Safety Program: Weather Accident Prevention (WxAP) Project Overview and Status

    NASA Technical Reports Server (NTRS)

    Nadell, Shari-Beth

    2003-01-01

    This paper presents a project overview and status for the Weather Accident Prevention (WxAP) aviation safety program. The topics include: 1) Weather Accident Prevention Project Background/History; 2) Project Modifications; 3) Project Accomplishments; and 4) Project's Next Steps.

  15. Systemic accident analysis: examining the gap between research and practice.

    PubMed

    Underwood, Peter; Waterson, Patrick

    2013-06-01

    The systems approach is arguably the dominant concept within accident analysis research. Viewing accidents as a result of uncontrolled system interactions, it forms the theoretical basis of various systemic accident analysis (SAA) models and methods. Despite the proposed benefits of SAA, such as an improved description of accident causation, evidence within the scientific literature suggests that these techniques are not being used in practice and that a research-practice gap exists. The aim of this study was to explore the issues stemming from research and practice which could hinder the awareness, adoption and usage of SAA. To achieve this, semi-structured interviews were conducted with 42 safety experts from ten countries and a variety of industries, including rail, aviation and maritime. This study suggests that the research-practice gap should be closed and efforts to bridge the gap should focus on ensuring that systemic methods meet the needs of practitioners and improving the communication of SAA research. Copyright © 2013 Elsevier Ltd. All rights reserved.

  16. Hazard Identification and Risk Assessment of Health and Safety Approach JSA (Job Safety Analysis) in Plantation Company

    NASA Astrophysics Data System (ADS)

    Sugarindra, Muchamad; Ragil Suryoputro, Muhammad; Tiya Novitasari, Adi

    2017-06-01

    Plantation company needed to identify hazard and perform risk assessment as an Identification of Hazard and Risk Assessment Crime and Safety which was approached by using JSA (Job Safety Analysis). The identification was aimed to identify the potential hazards that might be the risk of workplace accidents so that preventive action could be taken to minimize the accidents. The data was collected by direct observation to the workers concerned and the results were recorded on a Job Safety Analysis form. The data were as forklift operator, macerator worker, worker’s creeper, shredder worker, workers’ workshop, mechanical line worker, trolley cleaning workers and workers’ crepe decline. The result showed that shredder worker value was 30 and had the working level with extreme risk with the risk value range was above 20. So to minimize the accidents could provide Personal Protective Equipment (PPE) which were appropriate, information about health and safety, the company should have watched the activities of workers, and rewards for the workers who obey the rules that applied in the plantation.

  17. Work-related accidents among the Iranian population: a time series analysis, 2000–2011

    PubMed Central

    Karimlou, Masoud; Imani, Mehdi; Hosseini, Agha-Fatemeh; Dehnad, Afsaneh; Vahabi, Nasim; Bakhtiyari, Mahmood

    2015-01-01

    Background Work-related accidents result in human suffering and economic losses and are considered as a major health problem worldwide, especially in the economically developing world. Objectives To introduce seasonal autoregressive moving average (ARIMA) models for time series analysis of work-related accident data for workers insured by the Iranian Social Security Organization (ISSO) between 2000 and 2011. Methods In this retrospective study, all insured people experiencing at least one work-related accident during a 10-year period were included in the analyses. We used Box–Jenkins modeling to develop a time series model of the total number of accidents. Results There was an average of 1476 accidents per month (1476·05±458·77, mean±SD). The final ARIMA (p,d,q) (P,D,Q)s model for fitting to data was: ARIMA(1,1,1)×(0,1,1)12 consisting of the first ordering of the autoregressive, moving average and seasonal moving average parameters with 20·942 mean absolute percentage error (MAPE). Conclusions The final model showed that time series analysis of ARIMA models was useful for forecasting the number of work-related accidents in Iran. In addition, the forecasted number of work-related accidents for 2011 explained the stability of occurrence of these accidents in recent years, indicating a need for preventive occupational health and safety policies such as safety inspection. PMID:26119774

  18. Preliminary analysis of loss-of-coolant accident in Fukushima nuclear accident

    NASA Astrophysics Data System (ADS)

    Su'ud, Zaki; Anshari, Rio

    2012-06-01

    Loss-of-Coolant Accident (LOCA) in Boiling Water Reactor (BWR) especially on Fukushima Nuclear Accident will be discussed in this paper. The Tohoku earthquake triggered the shutdown of nuclear power reactors at Fukushima Nuclear Power station. Though shutdown process has been completely performed, cooling process, at much smaller level than in normal operation, is needed to remove decay heat from the reactor core until the reactor reach cold-shutdown condition. If LOCA happen at this condition, it will cause the increase of reactor fuel and other core temperatures and can lead to reactor core meltdown and exposure of radioactive material to the environment such as in the Fukushima Dai Ichi nuclear accident case. In this study numerical simulation has been performed to calculate pressure composition, water level and temperature distribution on reactor during this accident. There are two coolant regulating system that operational on reactor unit 1 at this accident, Isolation Condensers (IC) system and Safety Relief Valves (SRV) system. Average mass flow of steam to the IC system in this event is 10 kg/s and could keep reactor core from uncovered about 3,2 hours and fully uncovered in 4,7 hours later. There are two coolant regulating system at operational on reactor unit 2, Reactor Core Isolation Condenser (RCIC) System and Safety Relief Valves (SRV). Average mass flow of coolant that correspond this event is 20 kg/s and could keep reactor core from uncovered about 73 hours and fully uncovered in 75 hours later. There are three coolant regulating system at operational on reactor unit 3, Reactor Core Isolation Condenser (RCIC) system, High Pressure Coolant Injection (HPCI) system and Safety Relief Valves (SRV). Average mass flow of water that correspond this event is 15 kg/s and could keep reactor core from uncovered about 37 hours and fully uncovered in 40 hours later.

  19. Safety Climate and Occupational Stress According to Occupational Accidents Experience and Employment Type in Shipbuilding Industry of Korea.

    PubMed

    Kim, Kyung Woo; Park, Sung Jin; Lim, Hae Sun; Cho, Hm Hak

    2017-09-01

    Safety climate and occupational stress are related with occupational accident. The present study tried to identify the differences in safety climate and occupational stress according to occupational accidents experience and employment type (e.g., direct workers and subcontract workers). In this study, we conducted a survey using safety climate scale and Korean Occupational Stress Scale and classified the participants into four groups: direct workers working for accident-free departments, direct workers working for accident departments, subcontract workers working for accident-free departments, and subcontract workers working for accident departments for 2 years within the same workplace in the shipbuilding industry. The direct workers and subcontract workers showed diverse results in subscales of safety climate and occupational stress. This result is supported by existing studies; however, further study is necessary for more supporting evidence and elaborative methodological approach. The necessity of management for safety climate and psychosocial factor such as occupational stress for both direct workers and subcontract workers as a whole is suggested by this study.

  20. The Analysis of the Contribution of Human Factors to the In-Flight Loss of Control Accidents

    NASA Technical Reports Server (NTRS)

    Ancel, Ersin; Shih, Ann T.

    2012-01-01

    In-flight loss of control (LOC) is currently the leading cause of fatal accidents based on various commercial aircraft accident statistics. As the Next Generation Air Transportation System (NextGen) emerges, new contributing factors leading to LOC are anticipated. The NASA Aviation Safety Program (AvSP), along with other aviation agencies and communities are actively developing safety products to mitigate the LOC risk. This paper discusses the approach used to construct a generic integrated LOC accident framework (LOCAF) model based on a detailed review of LOC accidents over the past two decades. The LOCAF model is comprised of causal factors from the domain of human factors, aircraft system component failures, and atmospheric environment. The multiple interdependent causal factors are expressed in an Object-Oriented Bayesian belief network. In addition to predicting the likelihood of LOC accident occurrence, the system-level integrated LOCAF model is able to evaluate the impact of new safety technology products developed in AvSP. This provides valuable information to decision makers in strategizing NASA's aviation safety technology portfolio. The focus of this paper is on the analysis of human causal factors in the model, including the contributions from flight crew and maintenance workers. The Human Factors Analysis and Classification System (HFACS) taxonomy was used to develop human related causal factors. The preliminary results from the baseline LOCAF model are also presented.

  1. Archetypes for Organisational Safety

    NASA Technical Reports Server (NTRS)

    Marais, Karen; Leveson, Nancy G.

    2003-01-01

    We propose a framework using system dynamics to model the dynamic behavior of organizations in accident analysis. Most current accident analysis techniques are event-based and do not adequately capture the dynamic complexity and non-linear interactions that characterize accidents in complex systems. In this paper we propose a set of system safety archetypes that model common safety culture flaws in organizations, i.e., the dynamic behaviour of organizations that often leads to accidents. As accident analysis and investigation tools, the archetypes can be used to develop dynamic models that describe the systemic and organizational factors contributing to the accident. The archetypes help clarify why safety-related decisions do not always result in the desired behavior, and how independent decisions in different parts of the organization can combine to impact safety.

  2. Police accident report forms: safety device coding and enacted laws.

    PubMed

    Brock, K; Lapidus, G

    2008-12-01

    Safety device coding on state police accident report (PAR) forms was compared with provisions in state traffic safety laws. PAR forms were obtained from all 50 states and the District of Columbia (states/DC). For seat belts, 22 states/DC had a primary seat belt enforcement law vs 50 with a PAR code. For car seats, all 51 states/DC had a law and a PAR code. For booster seats, 39 states/DC had a law vs nine with a PAR code. For motorcycle helmets, 21 states/DC had an all-age rider helmet law and another 26 a partial-age law vs 50 with a PAR code. For bicycle helmets, 21 states/DC had a partial-age rider helmet law vs 48 with a PAR code. Therefore gaps in the ability of states to fully record accident data reflective of existing state traffic safety laws are revealed. Revising the PAR forms in all states to include complete variables for safety devices should be an important priority, independent of the laws.

  3. Exploring inattention and distraction in the SafetyNet Accident Causation Database.

    PubMed

    Talbot, Rachel; Fagerlind, Helen; Morris, Andrew

    2013-11-01

    Distraction and inattention are considered to be very important and prevalent factors in the causation of road accidents. There have been many recent research studies which have attempted to understand the circumstances under which a driver becomes distracted or inattentive and how distraction/inattention can be prevented. Both factors are thought to have become more important in recent times partly due to the evolution of in-vehicle information and communication technology. This study describes a methodology that was developed to understand when factors such as distraction and inattention may have been contributors to crashes and also describes some of the consequences of distraction and inattention in terms of subsequent driver actions. The study uses data relating to distraction and inattention from the SafetyNet Accident Causation Database. This database was formulated as part of the SafetyNet project to address the lack of representative in-depth accident causation data within the European Union. Data were collected in 6 European countries using 'on-scene' and 'nearly on-scene' crash investigation methodologies. 32% of crashes recorded in the database, involved at least one driver, rider or pedestrian, who was determined to be 'Inattentive' or 'Distracted'. 212 of the drivers were assigned 'Distraction' and 140 drivers were given the code 'Inattention'. It was found that both distraction and inattention often lead to missed observations within the driving task and consequently 'Timing' or 'Direction' become critical events in the aetiology of crashes. In addition, the crash types and outcomes may differ according to the type and nature of the distraction and inattention as determined by the in-depth investigations. The development of accident coding methodology is described in this study as is its evolution into the Driver Reliability and Error Analysis Model (DREAM) version 3.0. Copyright © 2012 Elsevier Ltd. All rights reserved.

  4. Content analysis of 100 consecutive media reports of amusement ride accidents.

    PubMed

    Woodcock, Kathryn

    2008-01-01

    Accident investigations influence public perceptions and safety management strategies by determining the amount and type of information learned about the accident. To examine the factors considered in investigations, this study used a content analysis of 100 consecutive media reports of amusement ride accidents from an online media archive. Fatalities were overrepresented in the media dataset compared with U.S. national estimates. For analysis of reports, a modified "Haddon matrix" was developed using human-factors categories. This approach was useful to show differences between the proportions and types of factors considered in the different accident stages and between employee and rider accidents. Employee injury accounts primarily referred to the employee's task and to the employee. Rider injury reports were primarily related to the ride device itself and rarely referred to the rider's "task", social influences, or the rider's own actions, and only some reference to their characteristics. Qualitatively, it was evident that more human factors analysis is required to augment scant pre-failure information about the task, social environment, and the person, to make that information available for prevention of amusement ride accidents. By design, this study reflected information reported by the media. Future work will use the same techniques with official reports.

  5. [Development and effect analysis of web-based instruction program to prevent elementary school students from safety accidents].

    PubMed

    Chung, Eun-Soon; Jeong, Ihn-Sook; Song, Mi-Gyoung

    2004-06-01

    This study was aimed to develop a WBI(Web Based Instruction) program on safety for 3rd grade elementary school students and to test the effects of it. The WBI program was developed using Macromedia flash MX, Adobe Illustrator 10.0 and Adobe Photoshop 7.0. The web site was http://www.safeschool.co.kr. The effect of it was tested from Mar 24, to Apr 30, 2003. The subjects were 144 students enrolled in the 3rd grade of an elementary school in Gyungju. The experimental group received the WBI program lessons while each control group received textbook-based lessons with visual presenters and maps, 3 times. Data was analyzed with descriptive statistics, and chi2 test, t-test, and repeated measure ANOVA. First, the WBI group reported a longer effect on knowledge and practice of accident prevention than the textbook-based lessons, indicating that the WBI is more effective. Second, the WBI group was better motivated to learn the accident prevention lessons, showing that the WBI is effective. As a result, the WBI group had total longer effects on knowledge, practice and motivation of accident prevention than the textbook-based instruction. We recommend that this WBI program be used in each class to provide more effective safety instruction in elementary schools.

  6. Safety climate as a mediator between foundation climates and occupational accidents: a group-level investigation.

    PubMed

    Wallace, J Craig; Popp, Eric; Mondore, Scott

    2006-05-01

    Building on recent work in occupational safety and climate, the authors examined 2 organizational foundation climates thought to be antecedents of specific safety climate and the relationships among these climates and occupational accidents. It is believed that both foundation climates (i.e., management-employee relations and organizational support) will predict safety climate, which will in turn mediate the relationship between occupational accidents and these 2 distal foundation climates. Using a sample of 9,429 transportation workers in 253 work groups, the authors tested the proposed relationships at the group level. Results supported all hypotheses. Overall it appears that different climates have direct and indirect effects on occupational accidents.

  7. Systems-based accident analysis in the led outdoor activity domain: application and evaluation of a risk management framework.

    PubMed

    Salmon, P; Williamson, A; Lenné, M; Mitsopoulos-Rubens, E; Rudin-Brown, C M

    2010-08-01

    Safety-compromising accidents occur regularly in the led outdoor activity domain. Formal accident analysis is an accepted means of understanding such events and improving safety. Despite this, there remains no universally accepted framework for collecting and analysing accident data in the led outdoor activity domain. This article presents an application of Rasmussen's risk management framework to the analysis of the Lyme Bay sea canoeing incident. This involved the development of an Accimap, the outputs of which were used to evaluate seven predictions made by the framework. The Accimap output was also compared to an analysis using an existing model from the led outdoor activity domain. In conclusion, the Accimap output was found to be more comprehensive and supported all seven of the risk management framework's predictions, suggesting that it shows promise as a theoretically underpinned approach for analysing, and learning from, accidents in the led outdoor activity domain. STATEMENT OF RELEVANCE: Accidents represent a significant problem within the led outdoor activity domain. This article presents an evaluation of a risk management framework that can be used to understand such accidents and to inform the development of accident countermeasures and mitigation strategies for the led outdoor activity domain.

  8. Continuously improving safety of nuclear installations: An approach to be reinforced after the Fukushima accident

    NASA Astrophysics Data System (ADS)

    Repussard, Jacques; Schwarz, Michel

    2012-05-01

    After the Three Mile Island accident in 1979 and the Chernobyl accident in 1986, the Fukushima accident shows that the probability of a core meltdown accident in an LWR (Light Water Reactor) has been largely underestimated. The consequences of such an accident are unacceptable: except in the case of TMI2 (Three Mile Island 2) large areas around the damaged plants are contaminated for decades and populations have to be relocated for long periods. This article presents the French approach which consists in improving continuously the safety of the Nuclear Power Plants (NPP) on the basis of lessons learned from operating experience and from the progress in R&D (Research and Development). It details the key role played by IRSN (Institut de radioprotection et de sûreté nucléaire), the French TSO (Technical and scientific Safety Organization), and shows how the Fukushima accident contributes to this approach in improving NPP robustness. It concludes on the necessity to keep on networking TSOs, to share knowledge as well as R&D resources, with the ultimate goal of enhancing and harmonizing nuclear safety worldwide.

  9. Introduction of Bayesian network in risk analysis of maritime accidents in Bangladesh

    NASA Astrophysics Data System (ADS)

    Rahman, Sohanur

    2017-12-01

    Due to the unique geographic location, complex navigation environment and intense vessel traffic, a considerable number of maritime accidents occurred in Bangladesh which caused serious loss of life, property and environmental contamination. Based on the historical data of maritime accidents from 1981 to 2015, which has been collected from Department of Shipping (DOS) and Bangladesh Inland Water Transport Authority (BIWTA), this paper conducted a risk analysis of maritime accidents by applying Bayesian network. In order to conduct this study, a Bayesian network model has been developed to find out the relation among parameters and the probability of them which affect accidents based on the accident investigation report of Bangladesh. Furthermore, number of accidents in different categories has also been investigated in this paper. Finally, some viable recommendations have been proposed in order to ensure greater safety of inland vessels in Bangladesh.

  10. Preliminary analysis of loss-of-coolant accident in Fukushima nuclear accident

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Su'ud, Zaki; Anshari, Rio

    Loss-of-Coolant Accident (LOCA) in Boiling Water Reactor (BWR) especially on Fukushima Nuclear Accident will be discussed in this paper. The Tohoku earthquake triggered the shutdown of nuclear power reactors at Fukushima Nuclear Power station. Though shutdown process has been completely performed, cooling process, at much smaller level than in normal operation, is needed to remove decay heat from the reactor core until the reactor reach cold-shutdown condition. If LOCA happen at this condition, it will cause the increase of reactor fuel and other core temperatures and can lead to reactor core meltdown and exposure of radioactive material to the environmentmore » such as in the Fukushima Dai Ichi nuclear accident case. In this study numerical simulation has been performed to calculate pressure composition, water level and temperature distribution on reactor during this accident. There are two coolant regulating system that operational on reactor unit 1 at this accident, Isolation Condensers (IC) system and Safety Relief Valves (SRV) system. Average mass flow of steam to the IC system in this event is 10 kg/s and could keep reactor core from uncovered about 3,2 hours and fully uncovered in 4,7 hours later. There are two coolant regulating system at operational on reactor unit 2, Reactor Core Isolation Condenser (RCIC) System and Safety Relief Valves (SRV). Average mass flow of coolant that correspond this event is 20 kg/s and could keep reactor core from uncovered about 73 hours and fully uncovered in 75 hours later. There are three coolant regulating system at operational on reactor unit 3, Reactor Core Isolation Condenser (RCIC) system, High Pressure Coolant Injection (HPCI) system and Safety Relief Valves (SRV). Average mass flow of water that correspond this event is 15 kg/s and could keep reactor core from uncovered about 37 hours and fully uncovered in 40 hours later.« less

  11. Applying STAMP in Accident Analysis

    NASA Technical Reports Server (NTRS)

    Leveson, Nancy; Daouk, Mirna; Dulac, Nicolas; Marais, Karen

    2003-01-01

    Accident models play a critical role in accident investigation and analysis. Most traditional models are based on an underlying chain of events. These models, however, have serious limitations when used for complex, socio-technical systems. Previously, Leveson proposed a new accident model (STAMP) based on system theory. In STAMP, the basic concept is not an event but a constraint. This paper shows how STAMP can be applied to accident analysis using three different views or models of the accident process and proposes a notation for describing this process.

  12. Children's Acceptance of Safety Guidelines after Exposure to Televised Dramas Depicting Accidents.

    ERIC Educational Resources Information Center

    Cantor, Joanne; Omdahl, Becky L.

    1999-01-01

    Presents a study where grade-school children were exposed to a scene from a movie involving one of two activities (either fire- or water-related activities) and involving one of two outcomes (fatal accidents or neutral events). Finds that watching the dramatized accidents increased students' estimated importance of adopting safety guidelines and…

  13. Accident models for two-lane rural roads : segments and intersections

    DOT National Transportation Integrated Search

    1998-10-01

    This report is a direct step for the implementation of the Accident Analysis Module in the Interactive Highway Safety Design Model (IHSDM). The Accident Analysis Module is expected to estimate the safety of two-lane rural highway characteristics for ...

  14. 77 FR 45417 - Pipeline Safety: Inspection and Protection of Pipeline Facilities After Railway Accidents

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-07-31

    ... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration [Docket No... Accidents AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA); DOT. [[Page 45418

  15. Safety in Academic Chemistry Laboratories: Volume 2. Accident Prevention for Faculty and Administrators, 7th Edition.

    ERIC Educational Resources Information Center

    American Chemical Society, Washington, DC.

    This book contains volume 2 of 2 and describes safety guidelines for academic chemistry laboratories to prevent accidents for college and university students. Contents include: (1) "Organizing for Accident Prevention"; (2) "Personal Protective Equipment"; (3) "Labeling"; (4) "Material Safety Data Sheets (MSDSs)"; (5) "Preparing for Medical…

  16. A systemic analysis of South Korea Sewol ferry accident - Striking a balance between learning and accountability.

    PubMed

    Kee, Dohyung; Jun, Gyuchan Thomas; Waterson, Patrick; Haslam, Roger

    2017-03-01

    The South Korea Sewol ferry accident in April 2014 claimed the lives of over 300 passengers and led to criminal charges of 399 personnel concerned including imprisonment of 154 of them as of Oct 2014. Blame and punishment culture can be prevalent in a more hierarchical society like South Korea as shown in the aftermath of this disaster. This study aims to analyse the South Korea ferry accident using Rasmussen's risk management framework and the associated AcciMap technique and to propose recommendations drawn from an AcciMap-based focus group with systems safety experts. The data for the accident analysis were collected mainly from an interim investigation report by the Board of Audit and Inspection of Korea and major South Korean and foreign newspapers. The analysis showed that the accident was attributed to many contributing factors arising from front-line operators, management, regulators and government. It also showed how the multiple factors including economic, social and political pressures and individual workload contributed to the accident and how they affected each other. This AcciMap was presented to 27 safety researchers and experts at 'the legacy of Jens Rasmussen' symposium adjunct to ODAM2014. Their recommendations were captured through a focus group. The four main recommendations include forgive (no blame and punishment on individuals), analyse (socio-technical system-based), learn (from why things do not go wrong) and change (bottom-up safety culture and safety system management). The findings offer important insights into how this type of accident should be understood, analysed and the subsequent response. Copyright © 2016 Elsevier Ltd. All rights reserved.

  17. Safety of high-speed guided ground transportation systems : collision avoidance and accident survivability : volume 3 : accident survivability

    DOT National Transportation Integrated Search

    1993-03-01

    This report is the third of four volumes concerned with developing safety guidelines and specifications for high-speed guided ground transportation (HSGGT) collision avoidance and accident survivability. The overall approach taken in this study is to...

  18. Historical analysis of US pipeline accidents triggered by natural hazards

    NASA Astrophysics Data System (ADS)

    Girgin, Serkan; Krausmann, Elisabeth

    2015-04-01

    Natural hazards, such as earthquakes, floods, landslides, or lightning, can initiate accidents in oil and gas pipelines with potentially major consequences on the population or the environment due to toxic releases, fires and explosions. Accidents of this type are also referred to as Natech events. Many major accidents highlight the risk associated with natural-hazard impact on pipelines transporting dangerous substances. For instance, in the USA in 1994, flooding of the San Jacinto River caused the rupture of 8 and the undermining of 29 pipelines by the floodwaters. About 5.5 million litres of petroleum and related products were spilled into the river and ignited. As a results, 547 people were injured and significant environmental damage occurred. Post-incident analysis is a valuable tool for better understanding the causes, dynamics and impacts of pipeline Natech accidents in support of future accident prevention and mitigation. Therefore, data on onshore hazardous-liquid pipeline accidents collected by the US Pipeline and Hazardous Materials Safety Administration (PHMSA) was analysed. For this purpose, a database-driven incident data analysis system was developed to aid the rapid review and categorization of PHMSA incident reports. Using an automated data-mining process followed by a peer review of the incident records and supported by natural hazard databases and external information sources, the pipeline Natechs were identified. As a by-product of the data-collection process, the database now includes over 800,000 incidents from all causes in industrial and transportation activities, which are automatically classified in the same way as the PHMSA record. This presentation describes the data collection and reviewing steps conducted during the study, provides information on the developed database and data analysis tools, and reports the findings of a statistical analysis of the identified hazardous liquid pipeline incidents in terms of accident dynamics and

  19. Balloon crash damage and injuries: an analysis of 86 accidents, 2000-2004.

    PubMed

    de Voogt, Alexander J; van Doorn, Robert R A

    2006-05-01

    General aviation accounts for the majority of aviation crashes and casualties in the United States. The role of ballooning in these statistics is not regularly studied. Since 2001, the National Transportation and Safety Board has made its accident reports more readily available, which presents opportunities for further study. This study analyzes and compares a 5-yr period of accident reports and includes an analysis of injuries and balloon damage in hot-air and gas balloon accidents. Balloon crash 2-page briefs and 5-page accident reports published by the National Transportation and Safety Board for the 5-yr time period 2000-2004 were examined. Data collected in the investigation of these crashes were analyzed and compared with the epidemiological data collected in earlier research. In 86 crashes during a 5-yr period, there were 4 fatalities and 75 people were seriously injured. Only one accident was reported involving a student pilot. Broken ankles and legs have been the most commonly recorded serious injury, but could not be linked to the severity of damage to the balloon. The absence of student pilot accidents may be explained by possible stricter supervision. Balloon basket and envelopes appear of sufficient quality to withstand crashes, but improving the protection of passengers during hard landings should help to decrease the number of serious injuries in ballooning.

  20. Accident Analysis for the NIST Research Reactor Before and After Fuel Conversion

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Baek J.; Diamond D.; Cuadra, A.

    Postulated accidents have been analyzed for the 20 MW D2O-moderated research reactor (NBSR) at the National Institute of Standards and Technology (NIST). The analysis has been carried out for the present core, which contains high enriched uranium (HEU) fuel and for a proposed equilibrium core with low enriched uranium (LEU) fuel. The analyses employ state-of-the-art calculational methods. Three-dimensional Monte Carlo neutron transport calculations were performed with the MCNPX code to determine homogenized fuel compositions in the lower and upper halves of each fuel element and to determine the resulting neutronic properties of the core. The accident analysis employed a modelmore » of the primary loop with the RELAP5 code. The model includes the primary pumps, shutdown pumps outlet valves, heat exchanger, fuel elements, and flow channels for both the six inner and twenty-four outer fuel elements. Evaluations were performed for the following accidents: (1) control rod withdrawal startup accident, (2) maximum reactivity insertion accident, (3) loss-of-flow accident resulting from loss of electrical power with an assumption of failure of shutdown cooling pumps, (4) loss-of-flow accident resulting from a primary pump seizure, and (5) loss-of-flow accident resulting from inadvertent throttling of a flow control valve. In addition, natural circulation cooling at low power operation was analyzed. The analysis shows that the conversion will not lead to significant changes in the safety analysis and the calculated minimum critical heat flux ratio and maximum clad temperature assure that there is adequate margin to fuel failure.« less

  1. Transit safety & security statistics & analysis 2003 annual report (formerly SAMIS)

    DOT National Transportation Integrated Search

    2005-12-01

    The Transit Safety & Security Statistics & Analysis 2003 Annual Report (formerly SAMIS) is a compilation and analysis of mass transit accident, casualty, and crime statistics reported under the Federal Transit Administrations (FTAs) National Tr...

  2. Transit safety & security statistics & analysis 2002 annual report (formerly SAMIS)

    DOT National Transportation Integrated Search

    2004-12-01

    The Transit Safety & Security Statistics & Analysis 2002 Annual Report (formerly SAMIS) is a compilation and analysis of mass transit accident, casualty, and crime statistics reported under the Federal Transit Administrations (FTAs) National Tr...

  3. A methodology for accident analysis of fusion breeder blankets and its application to helium-cooled lead–lithium blanket

    DOE PAGES

    Panayotov, Dobromir; Poitevin, Yves; Grief, Andrew; ...

    2016-09-23

    'Fusion for Energy' (F4E) is designing, developing, and implementing the European Helium-Cooled Lead-Lithium (HCLL) and Helium-Cooled Pebble-Bed (HCPB) Test Blanket Systems (TBSs) for ITER (Nuclear Facility INB-174). Safety demonstration is an essential element for the integration of these TBSs into ITER and accident analysis is one of its critical components. A systematic approach to accident analysis has been developed under the F4E contract on TBS safety analyses. F4E technical requirements, together with Amec Foster Wheeler and INL efforts, have resulted in a comprehensive methodology for fusion breeding blanket accident analysis that addresses the specificity of the breeding blanket designs, materials,more » and phenomena while remaining consistent with the approach already applied to ITER accident analyses. Furthermore, the methodology phases are illustrated in the paper by its application to the EU HCLL TBS using both MELCOR and RELAP5 codes.« less

  4. Road Traffic Accident Analysis of Ajmer City Using Remote Sensing and GIS Technology

    NASA Astrophysics Data System (ADS)

    Bhalla, P.; Tripathi, S.; Palria, S.

    2014-12-01

    With advancement in technology, new and sophisticated models of vehicle are available and their numbers are increasing day by day. A traffic accident has multi-facet characteristics associated with it. In India 93% of crashes occur due to Human induced factor (wholly or partly). For proper traffic accident analysis use of GIS technology has become an inevitable tool. The traditional accident database is a summary spreadsheet format using codes and mileposts to denote location, type and severity of accidents. Geo-referenced accident database is location-referenced. It incorporates a GIS graphical interface with the accident information to allow for query searches on various accident attributes. Ajmer city, headquarter of Ajmer district, Rajasthan has been selected as the study area. According to Police records, 1531 accidents occur during 2009-2013. Maximum accident occurs in 2009 and the maximum death in 2013. Cars, jeeps, auto, pickup and tempo are mostly responsible for accidents and that the occurrence of accidents is mostly concentrated between 4PM to 10PM. GIS has proved to be a good tool for analyzing multifaceted nature of accidents. While road safety is a critical issue, yet it is handled in an adhoc manner. This Study is a demonstration of application of GIS for developing an efficient database on road accidents taking Ajmer City as a study. If such type of database is developed for other cities, a proper analysis of accidents can be undertaken and suitable management strategies for traffic regulation can be successfully proposed.

  5. Preliminary Results Obtained in Integrated Safety Analysis of NASA Aviation Safety Program Technologies

    NASA Technical Reports Server (NTRS)

    Reveley, Mary S.

    2003-01-01

    The goal of the NASA Aviation Safety Program (AvSP) is to develop and demonstrate technologies that contribute to a reduction in the aviation fatal accident rate by a factor of 5 by the year 2007 and by a factor of 10 by the year 2022. Integrated safety analysis of day-to-day operations and risks within those operations will provide an understanding of the Aviation Safety Program portfolio. Safety benefits analyses are currently being conducted. Preliminary results for the Synthetic Vision Systems (SVS) and Weather Accident Prevention (WxAP) projects of the AvSP have been completed by the Logistics Management Institute under a contract with the NASA Glenn Research Center. These analyses include both a reliability analysis and a computer simulation model. The integrated safety analysis method comprises two principal components: a reliability model and a simulation model. In the reliability model, the results indicate how different technologies and systems will perform in normal, degraded, and failed modes of operation. In the simulation, an operational scenario is modeled. The primary purpose of the SVS project is to improve safety by providing visual-flightlike situation awareness during instrument conditions. The current analyses are an estimate of the benefits of SVS in avoiding controlled flight into terrain. The scenario modeled has an aircraft flying directly toward a terrain feature. When the flight crew determines that the aircraft is headed toward an obstruction, the aircraft executes a level turn at speed. The simulation is ended when the aircraft completes the turn.

  6. Government: Nuclear Safety in Doubt a Year after Accident.

    ERIC Educational Resources Information Center

    Ember, Lois R.

    1980-01-01

    A year after the accident at Three Mile Island (TMI), the signals transmitted to the public are still confused. Industry says that nuclear power is safe and that the aftermath of TMI ushers in a new era of safety. Antinuclear activists say TMI sounded nuclear power's death knell. (Author/RE)

  7. Tank car accident data analysis

    DOT National Transportation Integrated Search

    1991-06-01

    This report presents the results of a study of accidents involving railroad tank cars. The study is part of an overall effort to provide improved safety of rail transportation at reduced life-cycle costs. A major goal of the study is to provide a tec...

  8. Proceedings of the Second NASA Aviation Safety Program Weather Accident Prevention Review

    NASA Technical Reports Server (NTRS)

    Martzaklis, K. Gus (Compiler)

    2003-01-01

    The Second NASA Aviation Safety Program (AvSP) Weather Accident Prevention (WxAP) Annual Project Review held June 5-7, 2001, in Cleveland, Ohio, presented the NASA technical plans and accomplishments to the aviation community. NASA-developed technologies presented included an Aviation Weather Information System with associated digital communications links, electronic atmospheric reporting technologies, forward-looking turbulence warning systems, and turbulence mitigation procedures. The meeting provided feedback and insight from the aviation community of diverse backgrounds and assisted NASA in steering its plans in the direction needed to meet the national safety goal of 80-percent reduction of aircraft accidents by 2007. The proceedings of the review are enclosed.

  9. Analysis of Workplace Accidents in Automotive Repair Workshops in Spain.

    PubMed

    López-Arquillos, Antonio; Rubio-Romero, Juan Carlos

    2016-09-01

    To analyze the effects of the factors associated with different types of injury (superficial wounds, dislocations and sprains, bone fractures, concussion and internal injuries, burns scalding and freezing) caused by occupational accidents in automotive repair workshops. Study of a sample consisting of 89,954 industry accidents reported from 2003 to 2008. Odds ratios were calculated with a 95% confidence interval. Belonging to a small company is a risk factor for suffering three of the five types of injury studied. Women are less likely to suffer burns and superficial wounds, and more likely to suffer dislocations or sprains. Foreign workers are more likely to suffer concussion and internal injuries. Health and safety strategies and accident prevention measures should be individualized and adapted to the type of worker most likely to be injured in each type of accident. Occupational health and safety training courses designed according to worker profile, and improving the participation of the workers in small firms creating regional or roving safety representatives would improve working conditions.

  10. National and regional analysis of road accidents in Spain.

    PubMed

    Tolón-Becerra, A; Lastra-Bravo, X; Flores-Parra, I

    2013-01-01

    In Spain, the absolute fatality figures decreased almost 50 percent between 1998 and 2009. Despite this great effort, road mortality is still of great concern to political authorities. Further progress requires efficient road safety policy based on an optimal set of measures and targets that consider the initial conditions and characteristics in each region. This study attempts to analyze road accidents in Spain and its provinces in time and space during 1998-2009. First, we analyzed daily, monthly, and nationwide (NUTS 0) development of road accidents, the correlation between logarithmic transformations of road accidents and territorial and socioeconomic variables, the causality by simple linear regression of road accidents and territorial and socioeconomic variables, and preliminary frequency by fast Fourier transform. Then we analyzed the annual trend in accidents in the Spanish provinces (NUTS 3) and found a correlation between the logarithmic transformations of the mortality rate, fatalities per fatal accident, and accidents resulting in injuries per inhabitant variables and population, population density, gross domestic product (GDP), length of road network, and area. Finally, causality was analyzed by simple linear regression. The most outstanding results were the negative correlation between mortality rate and population density in Spanish provinces, which has increased over time, and that road accidents in Spain have an approximate periodicity of 57 days. The fast Fourier transform analysis of road accident frequency in Spain was useful in identifying the periodic, harmonic components of accidents and casualties. The periodicity observed both for the period 1998-2009 and by year showed that the highest intensity in road accidents was bimonthly, despite the lower number of accidents and casualties in the spectra of amplitude and power and efforts to reduce the intensity and concentration during off-season travel (summer and December).

  11. Safety in Academic Chemistry Laboratories: Volume 1. Accident Prevention for College and University Students, 7th Edition.

    ERIC Educational Resources Information Center

    American Chemical Society, Washington, DC.

    This book contains volume 1 of 2 and describes safety guidelines for academic chemistry laboratories to prevent accidents for college and university students. Contents include: (1) "Your Responsibility for Accident Prevention"; (2) "Guide to Chemical Hazards"; (3) "Recommended Laboratory Techniques"; and (4) "Safety Equipment and Emergency…

  12. Highway Safety Program Manual: Volume 9: Identification and Surveillance of Accident Locations.

    ERIC Educational Resources Information Center

    National Highway Traffic Safety Administration (DOT), Washington, DC.

    Volume 9 of the 19-volume Highway Safety Program Manual (which provides guidance to State and local governments on preferred highway safety practices) focuses on identification and surveillance of accident locations. The purpose of the program, its specific objectives, and its relationship with other programs are explored. Federal authority in the…

  13. Type A behavior pattern, accident optimism and fatalism: an investigation into non-compliance with safety work behaviors among hospital nurses.

    PubMed

    Ugwu, Fabian O; Onyishi, Ike E; Ugwu, Chidi; Onyishi, Charity N

    2015-01-01

    Safety work behavior has continued to attract the interest of organizational researchers and practitioners especially in the health sector. The goal of the study was to investigate whether personality type A, accident optimism and fatalism could predict non-compliance with safety work behaviors among hospital nurses. One hundred and fifty-nine nursing staff sampled from three government-owned hospitals in a state in southeast Nigeria, participated in the study. Data were collected through Type A Behavior Scale (TABS), Accident Optimism, Fatalism and Compliance with Safety Behavior (CSB) Scales. Our results showed that personality type A, accident optimism and fatalism were all related to non-compliance with safety work behaviors. Personality type A individuals tend to comply less with safety work behaviors than personality type B individuals. In addition, optimistic and fatalistic views about accidents and existing safety rules also have implications for compliance with safety work behaviors.

  14. 41 CFR 102-80.130 - Who must perform the equivalent level of safety analysis?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...-SAFETY AND ENVIRONMENTAL MANAGEMENT Accident and Fire Prevention Equivalent Level of Safety Analysis... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Who must perform the equivalent level of safety analysis? 102-80.130 Section 102-80.130 Public Contracts and Property Management...

  15. [Model of Analysis and Prevention of Accidents - MAPA: tool for operational health surveillance].

    PubMed

    de Almeida, Ildeberto Muniz; Vilela, Rodolfo Andrade de Gouveia; da Silva, Alessandro José Nunes; Beltran, Sandra Lorena

    2014-12-01

    The analysis of work-related accidents is important for accident surveillance and prevention. Current methods of analysis seek to overcome reductionist views that see these occurrences as simple events explained by operator error. The objective of this paper is to analyze the Model of Analysis and Prevention of Accidents (MAPA) and its use in monitoring interventions, duly highlighting aspects experienced in the use of the tool. The descriptive analytical method was used, introducing the steps of the model. To illustrate contributions and or difficulties, cases where the tool was used in the context of service were selected. MAPA integrates theoretical approaches that have already been tried in studies of accidents by providing useful conceptual support from the data collection stage until conclusion and intervention stages. Besides revealing weaknesses of the traditional approach, it helps identify organizational determinants, such as management failings, system design and safety management involved in the accident. The main challenges lie in the grasp of concepts by users, in exploring organizational aspects upstream in the chain of decisions or at higher levels of the hierarchy, as well as the intervention to change the determinants of these events.

  16. Structural Analysis for the American Airlines Flight 587 Accident Investigation: Global Analysis

    NASA Technical Reports Server (NTRS)

    Young, Richard D.; Lovejoy, Andrew E.; Hilburger, Mark W.; Moore, David F.

    2005-01-01

    NASA Langley Research Center (LaRC) supported the National Transportation Safety Board (NTSB) in the American Airlines Flight 587 accident investigation due to LaRC's expertise in high-fidelity structural analysis and testing of composite structures and materials. A Global Analysis Team from LaRC reviewed the manufacturer s design and certification procedures, developed finite element models and conducted structural analyses, and participated jointly with the NTSB and Airbus in subcomponent tests conducted at Airbus in Hamburg, Germany. The Global Analysis Team identified no significant or obvious deficiencies in the Airbus certification and design methods. Analysis results from the LaRC team indicated that the most-likely failure scenario was failure initiation at the right rear main attachment fitting (lug), followed by an unstable progression of failure of all fin-to-fuselage attachments and separation of the VTP from the aircraft. Additionally, analysis results indicated that failure initiates at the final observed maximum fin loading condition in the accident, when the VTP was subjected to loads that were at minimum 1.92 times the design limit load condition for certification. For certification, the VTP is only required to support loads of 1.5 times design limit load without catastrophic failure. The maximum loading during the accident was shown to significantly exceed the certification requirement. Thus, the structure appeared to perform in a manner consistent with its design and certification, and failure is attributed to VTP loads greater than expected.

  17. NASA Aviation Safety Program Weather Accident Prevention/weather Information Communications (WINCOMM)

    NASA Technical Reports Server (NTRS)

    Feinberg, Arthur; Tauss, James; Chomos, Gerald (Technical Monitor)

    2002-01-01

    Weather is a contributing factor in approximately 25-30 percent of general aviation accidents. The lack of timely, accurate and usable weather information to the general aviation pilot in the cockpit to enhance pilot situational awareness and improve pilot judgment remains a major impediment to improving aviation safety. NASA Glenn Research Center commissioned this 120 day weather datalink market survey to assess the technologies, infrastructure, products, and services of commercial avionics systems being marketed to the general aviation community to address these longstanding safety concerns. A market survey of companies providing or proposing to provide graphical weather information to the general aviation cockpit was conducted. Fifteen commercial companies were surveyed. These systems are characterized and evaluated in this report by availability, end-user pricing/cost, system constraints/limits and technical specifications. An analysis of market survey results and an evaluation of product offerings were made. In addition, recommendations to NASA for additional research and technology development investment have been made as a result of this survey to accelerate deployment of cockpit weather information systems for enhancing aviation safety.

  18. 10 CFR 76.85 - Assessment of accidents.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 10 Energy 2 2013-01-01 2013-01-01 false Assessment of accidents. 76.85 Section 76.85 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safety § 76.85 Assessment of accidents. The Corporation shall perform an analysis of potential accidents and consequences to...

  19. 10 CFR 76.85 - Assessment of accidents.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 10 Energy 2 2014-01-01 2014-01-01 false Assessment of accidents. 76.85 Section 76.85 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safety § 76.85 Assessment of accidents. The Corporation shall perform an analysis of potential accidents and consequences to...

  20. 10 CFR 76.85 - Assessment of accidents.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 10 Energy 2 2012-01-01 2012-01-01 false Assessment of accidents. 76.85 Section 76.85 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safety § 76.85 Assessment of accidents. The Corporation shall perform an analysis of potential accidents and consequences to...

  1. 10 CFR 76.85 - Assessment of accidents.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Assessment of accidents. 76.85 Section 76.85 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safety § 76.85 Assessment of accidents. The Corporation shall perform an analysis of potential accidents and consequences to...

  2. 10 CFR 76.85 - Assessment of accidents.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 10 Energy 2 2011-01-01 2011-01-01 false Assessment of accidents. 76.85 Section 76.85 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safety § 76.85 Assessment of accidents. The Corporation shall perform an analysis of potential accidents and consequences to...

  3. Investigating Accidents in the Workplace. A Manual for Compliance Safety and Health Officers.

    ERIC Educational Resources Information Center

    Occupational Safety and Health Administration, Washington, DC.

    This manual was developed for Compliance Safety and Health Officers (CSHO) of the Occupational Safety and Health Administration (OSHA) to help them carry out their responsibilities when investigating workplace accidents. The content is presented in four sections. The first overviews the investigative roles of CSHO officers, including…

  4. A Qualitative Study on Organizational Factors Affecting Occupational Accidents

    PubMed Central

    ESKANDARI, Davood; JAFARI, Mohammad Javad; MEHRABI, Yadollah; KIAN, Mostafa Pouya; CHARKHAND, Hossein; MIRGHOTBI, Mostafa

    2017-01-01

    Background: Technical, human, operational and organizational factors have been influencing the sequence of occupational accidents. Among them, organizational factors play a major role in causing occupational accidents. The aim of this research was to understand the Iranian safety experts’ experiences and perception of organizational factors. Methods: This qualitative study was conducted in 2015 by using the content analysis technique. Data were collected through semi-structured interviews with 17 safety experts working in Iranian universities and industries and analyzed with a conventional qualitative content analysis method using the MAXQDA software. Results: Eleven organizational factors’ sub-themes were identified: management commitment, management participation, employee involvement, communication, blame culture, education and training, job satisfaction, interpersonal relationship, supervision, continuous improvement, and reward system. The participants considered these factors as effective on occupational accidents. Conclusion: The mentioned 11 organizational factors are probably involved in occupational accidents in Iran. Naturally, improving organizational factors can increase the safety performance and reduce occupational accidents. PMID:28435824

  5. A Qualitative Study on Organizational Factors Affecting Occupational Accidents.

    PubMed

    Eskandari, Davood; Jafari, Mohammad Javad; Mehrabi, Yadollah; Kian, Mostafa Pouya; Charkhand, Hossein; Mirghotbi, Mostafa

    2017-03-01

    Technical, human, operational and organizational factors have been influencing the sequence of occupational accidents. Among them, organizational factors play a major role in causing occupational accidents. The aim of this research was to understand the Iranian safety experts' experiences and perception of organizational factors. This qualitative study was conducted in 2015 by using the content analysis technique. Data were collected through semi-structured interviews with 17 safety experts working in Iranian universities and industries and analyzed with a conventional qualitative content analysis method using the MAXQDA software. Eleven organizational factors' sub-themes were identified: management commitment, management participation, employee involvement, communication, blame culture, education and training, job satisfaction, interpersonal relationship, supervision, continuous improvement, and reward system. The participants considered these factors as effective on occupational accidents. The mentioned 11 organizational factors are probably involved in occupational accidents in Iran. Naturally, improving organizational factors can increase the safety performance and reduce occupational accidents.

  6. Underreporting of maritime accidents to vessel accident databases.

    PubMed

    Hassel, Martin; Asbjørnslett, Bjørn Egil; Hole, Lars Petter

    2011-11-01

    Underreporting of maritime accidents is a problem not only for authorities trying to improve maritime safety through legislation, but also to risk management companies and other entities using maritime casualty statistics in risk and accident analysis. This study collected and compared casualty data from 01.01.2005 to 31.12.2009, from IHS Fairplay and the maritime authorities from a set of nations. The data was compared to find common records, and estimation of the true number of occurred accidents was performed using conditional probability given positive dependency between data sources, several variations of the capture-recapture method, calculation of best case scenario assuming perfect reporting, and scaling up a subset of casualty information from a marine insurance statistics database. The estimated upper limit reporting performance for the selected flag states ranged from 14% to 74%, while the corresponding estimated coverage of IHS Fairplay ranges from 4% to 62%. On average the study results document that the number of unreported accidents makes up roughly 50% of all occurred accidents. Even in a best case scenario, only a few flag states come close to perfect reporting (94%). The considerable scope of underreporting uncovered in the study, indicates that users of statistical vessel accident data should assume a certain degree of underreporting, and adjust their analyses accordingly. Whether to use correction factors, a safety margin, or rely on expert judgment, should be decided on a case by case basis. Copyright © 2011 Elsevier Ltd. All rights reserved.

  7. Mines Systems Safety Improvement Using an Integrated Event Tree and Fault Tree Analysis

    NASA Astrophysics Data System (ADS)

    Kumar, Ranjan; Ghosh, Achyuta Krishna

    2017-04-01

    Mines systems such as ventilation system, strata support system, flame proof safety equipment, are exposed to dynamic operational conditions such as stress, humidity, dust, temperature, etc., and safety improvement of such systems can be done preferably during planning and design stage. However, the existing safety analysis methods do not handle the accident initiation and progression of mine systems explicitly. To bridge this gap, this paper presents an integrated Event Tree (ET) and Fault Tree (FT) approach for safety analysis and improvement of mine systems design. This approach includes ET and FT modeling coupled with redundancy allocation technique. In this method, a concept of top hazard probability is introduced for identifying system failure probability and redundancy is allocated to the system either at component or system level. A case study on mine methane explosion safety with two initiating events is performed. The results demonstrate that the presented method can reveal the accident scenarios and improve the safety of complex mine systems simultaneously.

  8. Utilization of accident databases and fuzzy sets to estimate frequency of HazMat transport accidents.

    PubMed

    Qiao, Yuanhua; Keren, Nir; Mannan, M Sam

    2009-08-15

    Risk assessment and management of transportation of hazardous materials (HazMat) require the estimation of accident frequency. This paper presents a methodology to estimate hazardous materials transportation accident frequency by utilizing publicly available databases and expert knowledge. The estimation process addresses route-dependent and route-independent variables. Negative binomial regression is applied to an analysis of the Department of Public Safety (DPS) accident database to derive basic accident frequency as a function of route-dependent variables, while the effects of route-independent variables are modeled by fuzzy logic. The integrated methodology provides the basis for an overall transportation risk analysis, which can be used later to develop a decision support system.

  9. An Analysis of Laboratory Safety in Texas.

    ERIC Educational Resources Information Center

    Fuller, Edward J.; Picucci, Ali Callicoatte; Collins, James W.; Swann, Philip

    This paper reports on a survey to discover the types of laboratory accidents that occur in Texas public schools, the factors associated with such accidents, and the practices of schools with regard to current laboratory safety requirements. The purpose of the survey is to better understand safety conditions in Texas public schools and to help…

  10. Aircraft accidents : method of analysis

    NASA Technical Reports Server (NTRS)

    1931-01-01

    The revised report includes the chart for the analysis of aircraft accidents, combining consideration of the immediate causes, underlying causes, and results of accidents, as prepared by the special committee, with a number of the definitions clarified. A brief statement of the organization and work of the special committee and of the Committee on Aircraft Accidents; and statistical tables giving a comparison of the types of accidents and causes of accidents in the military services on the one hand and in civil aviation on the other, together with explanations of some of the important differences noted in these tables.

  11. Sports Safety. Accident Prevention and Injury Control in Physical Education, Athletics, and Recreation.

    ERIC Educational Resources Information Center

    Yost, Charles Peter, Ed.

    This anthology of articles concerned with injury in sports and safety procedures is divided into three parts. Part One is devoted to general discussions of safety and a guiding philosophy for accident prevention. Part Two develops articles on administration and supervision, including discussions of health examination, legal liability, facilities,…

  12. Overview of Energy Systems' safety analysis report programs

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Not Available

    1992-03-01

    The primary purpose of an Safety Analysis Report (SAR) is to provide a basis for judging the adequacy of a facility's safety. The SAR documents the safety analyses that systematically identify the hazards posed by the facility, analyze the consequences and risk of potential accidents, and describe hazard control measures that protect the health and safety of the public and employees. In addition, some SARs document, as Technical Safety Requirements (TSRs, which include Technical Specifications and Operational Safety Requirements), technical and administrative requirements that ensure the facility is operated within prescribed safety limits. SARs also provide conveniently summarized information thatmore » may be used to support procedure development, training, inspections, and other activities necessary to facility operation. This Overview of Energy Systems Safety Analysis Report Programs'' Provides an introduction to the programs and processes used in the development and maintenance of the SARs. It also summarizes some of the uses of the SARs within Energy Systems and DOE.« less

  13. Methodological guidelines for developing accident modification functions.

    PubMed

    Elvik, Rune

    2015-07-01

    This paper proposes methodological guidelines for developing accident modification functions. An accident modification function is a mathematical function describing systematic variation in the effects of road safety measures. The paper describes ten guidelines. An example is given of how to use the guidelines. The importance of exploratory analysis and an iterative approach in developing accident modification functions is stressed. The example shows that strict compliance with all the guidelines may be difficult, but represents a level of stringency that should be strived for. Currently the main limitations in developing accident modification functions are the small number of good evaluation studies and the often huge variation in estimates of effect. It is therefore still not possible to develop accident modification functions for very many road safety measures. Copyright © 2015 Elsevier Ltd. All rights reserved.

  14. Another Approach to Enhance Airline Safety: Using Management Safety Tools

    NASA Technical Reports Server (NTRS)

    Lu, Chien-tsug; Wetmore, Michael; Przetak, Robert

    2006-01-01

    The ultimate goal of conducting an accident investigation is to prevent similar accidents from happening again and to make operations safer system-wide. Based on the findings extracted from the investigation, the "lesson learned" becomes a genuine part of the safety database making risk management available to safety analysts. The airline industry is no exception. In the US, the FAA has advocated the usage of the System Safety concept in enhancing safety since 2000. Yet, in today s usage of System Safety, the airline industry mainly focuses on risk management, which is a reactive process of the System Safety discipline. In order to extend the merit of System Safety and to prevent accidents beforehand, a specific System Safety tool needs to be applied; so a model of hazard prediction can be formed. To do so, the authors initiated this study by reviewing 189 final accident reports from the National Transportation Safety Board (NTSB) covering FAR Part 121 scheduled operations. The discovered accident causes (direct hazards) were categorized into 10 groups Flight Operations, Ground Crew, Turbulence, Maintenance, Foreign Object Damage (FOD), Flight Attendant, Air Traffic Control, Manufacturer, Passenger, and Federal Aviation Administration. These direct hazards were associated with 36 root factors prepared for an error-elimination model using Fault Tree Analysis (FTA), a leading tool for System Safety experts. An FTA block-diagram model was created, followed by a probability simulation of accidents. Five case studies and reports were provided in order to fully demonstrate the usefulness of System Safety tools in promoting airline safety.

  15. Impact of the effect of economic crisis and the targeted motorcycle safety programme on motorcycle-related accidents, injuries and fatalities in Malaysia.

    PubMed

    Law, T H; Umar, R S Radin; Zulkaurnain, S; Kulanthayan, S

    2005-03-01

    In 1997, a Motorcycle Safety Programme (MSP) was introduced to address the motorcycle-related accident problem. The MSP was specifically targeted at motorcyclists. In addition to the MSP, the recent economic recession has significantly contributed to a reduction of traffic-related incidents. This paper examines the effects of the recent economic crisis and the MSP on motorcycle-related accidents, casualties and fatalities in Malaysia. The autocorrelation integrated moving average model with transfer function was used to evaluate the overall effects of the interventions. The variables used in developing the model were gross domestic product and MSPs. The analysis found a 25% reduction in the number of motorcycle-related accidents, a 27% reduction in motorcycle casualties and a 38% reduction in motorcycle fatalities after the implementation of MSP. Findings indicate that the MSP has been one of the effective measures in reducing motorcycle safety problems in Malaysia. Apart from that, the performance of the country's economy was also found to be significant in explaining the number of motorcycle-related accidents, casualties and fatalities in Malaysia.

  16. Accident analysis and control options in support of the sludge water system safety analysis

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    HEY, B.E.

    A hazards analysis was initiated for the SWS in July 2001 (SNF-8626, K Basin Sludge and Water System Preliminary Hazard Analysis) and updated in December 2001 (SNF-10020 Rev. 0, Hazard Evaluation for KE Sludge and Water System - Project A16) based on conceptual design information for the Sludge Retrieval System (SRS) and 60% design information for the cask and container. SNF-10020 was again revised in September 2002 to incorporate new hazards identified from final design information and from a What-if/Checklist evaluation of operational steps. The process hazards, controls, and qualitative consequence and frequency estimates taken from these efforts have beenmore » incorporated into Revision 5 of HNF-3960, K Basins Hazards Analysis. The hazards identification process documented in the above referenced reports utilized standard industrial safety techniques (AIChE 1992, Guidelines for Hazard Evaluation Procedures) to systematically guide several interdisciplinary teams through the system using a pre-established set of process parameters (e.g., flow, temperature, pressure) and guide words (e.g., high, low, more, less). The teams generally included representation from the U.S. Department of Energy (DOE), K Basins Nuclear Safety, T Plant Nuclear Safety, K Basin Industrial Safety, fire protection, project engineering, operations, and facility engineering.« less

  17. Developing techniques for cause-responsibility analysis of occupational accidents.

    PubMed

    Jabbari, Mousa; Ghorbani, Roghayeh

    2016-11-01

    The aim of this study was to specify the causes of occupational accidents, determine social responsibility and the role of groups involved in work-related accidents. This study develops occupational accidents causes tree, occupational accidents responsibility tree, and occupational accidents component-responsibility analysis worksheet; based on these methods, it develops cause-responsibility analysis (CRA) techniques, and for testing them, analyzes 100 fatal/disabling occupational accidents in the construction setting that were randomly selected from all the work-related accidents in Tehran, Iran, over a 5-year period (2010-2014). The main result of this study involves two techniques for CRA: occupational accidents tree analysis (OATA) and occupational accidents components analysis (OACA), used in parallel for determination of responsible groups and responsibilities rate. From the results, we find that the management group of construction projects has 74.65% responsibility of work-related accidents. The developed techniques are purposeful for occupational accidents investigation/analysis, especially for the determination of detailed list of tasks, responsibilities, and their rates. Therefore, it is useful for preventing work-related accidents by focusing on the responsible group's duties. Copyright © 2016 Elsevier Ltd. All rights reserved.

  18. Software Safety Analysis of a Flight Guidance System

    NASA Technical Reports Server (NTRS)

    Butler, Ricky W. (Technical Monitor); Tribble, Alan C.; Miller, Steven P.; Lempia, David L.

    2004-01-01

    This document summarizes the safety analysis performed on a Flight Guidance System (FGS) requirements model. In particular, the safety properties desired of the FGS model are identified and the presence of the safety properties in the model is formally verified. Chapter 1 provides an introduction to the entire project, while Chapter 2 gives a brief overview of the problem domain, the nature of accidents, model based development, and the four-variable model. Chapter 3 outlines the approach. Chapter 4 presents the results of the traditional safety analysis techniques and illustrates how the hazardous conditions associated with the system trace into specific safety properties. Chapter 5 presents the results of the formal methods analysis technique model checking that was used to verify the presence of the safety properties in the requirements model. Finally, Chapter 6 summarizes the main conclusions of the study, first and foremost that model checking is a very effective verification technique to use on discrete models with reasonable state spaces. Additional supporting details are provided in the appendices.

  19. Analysis of multiple tank car releases in train accidents.

    PubMed

    Liu, Xiang; Liu, Chang; Hong, Yili

    2017-10-01

    There are annually over two million carloads of hazardous materials transported by rail in the United States. The American railroads use large blocks of tank cars to transport petroleum crude oil and other flammable liquids from production to consumption sites. Being different from roadway transport of hazardous materials, a train accident can potentially result in the derailment and release of multiple tank cars, which may result in significant consequences. The prior literature predominantly assumes that the occurrence of multiple tank car releases in a train accident is a series of independent Bernoulli processes, and thus uses the binomial distribution to estimate the total number of tank car releases given the number of tank cars derailing or damaged. This paper shows that the traditional binomial model can incorrectly estimate multiple tank car release probability by magnitudes in certain circumstances, thereby significantly affecting railroad safety and risk analysis. To bridge this knowledge gap, this paper proposes a novel, alternative Correlated Binomial (CB) model that accounts for the possible correlations of multiple tank car releases in the same train. We test three distinct correlation structures in the CB model, and find that they all outperform the conventional binomial model based on empirical tank car accident data. The analysis shows that considering tank car release correlations would result in a significantly improved fit of the empirical data than otherwise. Consequently, it is prudent to consider alternative modeling techniques when analyzing the probability of multiple tank car releases in railroad accidents. Copyright © 2017 Elsevier Ltd. All rights reserved.

  20. A review of inherent safety characteristics of metal alloy sodium-cooled fast reactor fuel against postulated accidents

    DOE PAGES

    Sofu, Tanju

    2015-04-01

    The thermal, mechanical, and neutronic performance of the metal alloy fast reactor fuel design complements the safety advantages of the liquid metal cooling and the pool-type primary system. Together, these features provide large safety margins in both normal operating modes and for a wide range of postulated accidents. In particular, they maximize the measures of safety associated with inherent reactor response to unprotected, double-fault accidents, and to minimize risk to the public and plant investment. High thermal conductivity and high gap conductance play the most significant role in safety advantages of the metallic fuel, resulting in a flatter radial temperaturemore » profile within the pin and much lower normal operation and transient temperatures in comparison to oxide fuel. Despite the big difference in melting point, both oxide and metal fuels have a relatively similar margin to melting during postulated accidents. When the metal fuel cladding fails, it typically occurs below the coolant boiling point and the damaged fuel pins remain coolable. Metal fuel is compatible with sodium coolant, eliminating the potential of energetic fuel--coolant reactions and flow blockages. All these, and the low retained heat leading to a longer grace period for operator action, are significant contributing factors to the inherently benign response of metallic fuel to postulated accidents. This paper summarizes the past analytical and experimental results obtained in past sodium-cooled fast reactor safety programs in the United States, and presents an overview of fuel safety performance as observed in laboratory and in-pile tests.« less

  1. A review of inherent safety characteristics of metal alloy sodium-cooled fast reactor fuel against postulated accidents

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Sofu, Tanju

    2015-04-01

    The thermal, mechanical, and neutronic performance of the metal alloy fast reactor fuel design complements the safety advantages of the liquid metal cooling and the pool-type primary system. Together, these features provide large safety margins in both normal operating modes and for a wide range of postulated accidents. In particular, they maximize the measures of safety associated with inherent reactor response to unprotected, double-fault accidents, and to minimize risk to the public and plant investment. High thermal conductivity and high gap conductance play the most significant role in safety advantages of the metallic fuel, resulting in a flatter radial temperaturemore » profile within the pin and much lower normal operation and transient temperatures in comparison to oxide fuel. Despite the big difference in melting point, both oxide and metal fuels have a relatively similar margin to melting during postulated accidents. When the metal fuel cladding fails, it typically occurs below the coolant boiling point and the damaged fuel pins remain cool-able. Metal fuel is compatible with sodium coolant, eliminating the potential of energetic fuel coolant reactions and flow blockages. All these, and the low retained heat leading to a longer grace period for operator action, are significant contributing factors to the inherently benign response of metallic fuel to postulated accidents. This paper summarizes the past analytical and experimental results obtained in past sodium-cooled fast reactor safety programs in the United States, and presents an overview of fuel safety performance as observed in laboratory and in-pile tests.« less

  2. Analysis of Material Handling Safety in Construction Sites and Countermeasures for Effective Enhancement

    PubMed Central

    Anil Kumar, C. N.; Sakthivel, M.; Elangovan, R. K.; Arularasu, M.

    2015-01-01

    One of many hazardous workplaces includes the construction sites as they involve several dangerous tasks. Many studies have revealed that material handling equipment is a major cause of accidents at these sites. Though safety measures are being followed and monitored continuously, accident rates are still high as either workers are unaware of hazards or the safety regulations are not being strictly followed. This paper analyses the safety management systems at construction sites through means of questionnaire surveys with employees, specifically referring to safety of material handling equipment. Based on results of the questionnaire surveys, two construction sites were selected for a safety education program targeting worker safety related to material handling equipment. Knowledge levels of the workers were gathered before and after the program and results obtained were subjected to a t-test analysis to mark significance level of the conducted safety education program. PMID:26446572

  3. Analysis of typical WWER-1000 severe accident scenarios

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Sorokin, Yu.S.; Shchekoldin, V.V.; Borisov, L.N.

    2004-07-01

    At present in EDO 'Gidropress' there is a certain experience of performing the analyses of severe accidents of reactor plant with WWER with application of domestic and foreign codes. Important data were also obtained by the results of calculation modeling of integrated experiments with fuel assembly melting comprising a real fuel. Systematization and consideration of these data in development and assimilation of codes are extremely important in connection with large uncertainty still existing in understanding and adequate description of phenomenology of severe accidents. The presented report gives a comparison of analysis results of severe accidents of reactor plant with WWER-1000more » for two typical scenarios made by using American MELCOR code and the Russian RATEG/SVECHA/HEFEST code. The results of calculation modeling are compared using above codes with the data of experiment FPT1 with fuel assembly melting comprising a real fuel, which has been carried out at the facility Phebus (France). The obtained results are considered in the report from the viewpoint of: - adequacy of results of calculation modeling of separate phenomena during severe accidents of RP with WWER by using the above codes; - influence of uncertainties (degree of details of calculation models, choice of parameters of models etc.); - choice of those or other setup variables (options) in the used codes; - necessity of detailed modeling of processes and phenomena as applied to design justification of safety of RP with WWER. (authors)« less

  4. Outline of the Fukushima Daiichi Accident. Lessons Learned and Safety Enhancements

    NASA Astrophysics Data System (ADS)

    Hirano, Masashi

    2017-09-01

    Abstract. On March 11, 2011, an earthquake and subsequent tsunamis off the Pacific coastline of Japan's Tohoku region caused widespread devastation in Japan. As of June 10, 2016, it is reported that a total of 15,894 people lost their lives and 2,558 people are still unaccounted for. In Fukushima Prefecture, approximately 100,000 people are still obliged to live away from their homes due to the earthquake and tsunami as well as the Fukushima Daiichi accident. On the day, the earthquake and tsunami caused severe damages to the Tokyo Electric Power Company (TEPCO)'s Fukushima Daiichi Nuclear Power Station (NPS). All the units in operation, namely Units 1 to 3, were automatically shut down on seismic reactor protection system trips but the earthquake led to the loss of all off-site electrical power supplies to that site. The subsequent tsunami inundated the site up to 4 to 5 m above its ground level and caused, in the end, the loss of core cooling function in Units 1 to 3, resulting in severe core damages and containment vessel failures in these three units. Hydrogen was released from the containment vessels, leading to explosions in the reactor buildings of Units 1, 3 and 4. Radioactive materials were released to the atmosphere and were deposited on the land and in the ocean. One of the most important lessons learned is an importance to prevent such large scale common cause failures due to extreme natural events. This leads to a conclusion that application of the defense-in-depth philosophy be enhanced because the defense-in-depth philosophy has been and continues to be an effective way to account for uncertainties associated with risks. From the human and organizational viewpoints, the final report from the Investigation Committee of the Government pointed out so-called "safety myth" that existed among nuclear operators including TEPCO as well as the government, that serious severe accidents could never occur in nuclear power plants in Japan. After the accident, the

  5. Demographic variables in coal miners’ safety attitude

    NASA Astrophysics Data System (ADS)

    Yin, Wen-wen; Wu, Xiang; Ci, Hui-Peng; Qin, Shu-Qi; Liu, Jia-Long

    2017-03-01

    To change unsafe behavior through adjusting people’s safety attitudes has become an important measure to prevent accidents. Demographic variables, as influential factors of safety attitude, are fundamental and essential for the research. This research does a questionnaire survey among coal mine industry workers, and makes variance analysis and correlation analysis of the results in light of age, length of working years, educational level and experiences of accidents. The results show that the coal miners’ age, length of working years and accident experiences correlate lowly with safety attitudes, and those older coal miners with longer working years have better safety attitude, as coal miners without experiences of accident do.However, educational level has nothing to do with the safety attitude. Therefore, during the process of safety management, coal miners with different demographic characteristics should be put more attention to.

  6. Farm accidents in children.

    PubMed Central

    Cameron, D.; Bishop, C.; Sibert, J. R.

    1992-01-01

    OBJECTIVE--To examine the problem of accidental injury to children on farms. DESIGN--Prospective county based study of children presenting to accident and emergency departments over 12 months with injuries sustained in a farm setting and nationwide review of fatal childhood farm accidents over the four years April 1986 to March 1990. SETTING--Accident and emergency departments in Aberystwyth, Carmarthen, Haverfordwest, and Llanelli and fatal accidents in England, Scotland, and Wales notified to the Health and Safety Executive register. SUBJECTS--Children aged under 16. MAIN OUTCOME MEASURE--Death or injury after farm related accidents. RESULTS--65 accidents were recorded, including 18 fractures. Nine accidents necessitated admission to hospital for a mean of two (range one to four) days. 13 incidents were related to tractors and other machinery; 24 were due to falls. None of these incidents were reported under the statutory notification scheme. 33 deaths were notified, eight related to tractors and allied machinery and 10 related to falling objects. CONCLUSIONS--Although safety is improving, the farm remains a dangerous environment for children. Enforcement of existing safety legislation with significant penalties and targeting of safety education will help reduce accident rates further. PMID:1638192

  7. Bayesian-network-based safety risk assessment for steel construction projects.

    PubMed

    Leu, Sou-Sen; Chang, Ching-Miao

    2013-05-01

    There are four primary accident types at steel building construction (SC) projects: falls (tumbles), object falls, object collapse, and electrocution. Several systematic safety risk assessment approaches, such as fault tree analysis (FTA) and failure mode and effect criticality analysis (FMECA), have been used to evaluate safety risks at SC projects. However, these traditional methods ineffectively address dependencies among safety factors at various levels that fail to provide early warnings to prevent occupational accidents. To overcome the limitations of traditional approaches, this study addresses the development of a safety risk-assessment model for SC projects by establishing the Bayesian networks (BN) based on fault tree (FT) transformation. The BN-based safety risk-assessment model was validated against the safety inspection records of six SC building projects and nine projects in which site accidents occurred. The ranks of posterior probabilities from the BN model were highly consistent with the accidents that occurred at each project site. The model accurately provides site safety-management abilities by calculating the probabilities of safety risks and further analyzing the causes of accidents based on their relationships in BNs. In practice, based on the analysis of accident risks and significant safety factors, proper preventive safety management strategies can be established to reduce the occurrence of accidents on SC sites. Copyright © 2013 Elsevier Ltd. All rights reserved.

  8. Analysis 320 coal mine accidents using structural equation modeling with unsafe conditions of the rules and regulations as exogenous variables.

    PubMed

    Zhang, Yingyu; Shao, Wei; Zhang, Mengjia; Li, Hejun; Yin, Shijiu; Xu, Yingjun

    2016-07-01

    Mining has been historically considered as a naturally high-risk industry worldwide. Deaths caused by coal mine accidents are more than the sum of all other accidents in China. Statistics of 320 coal mine accidents in Shandong province show that all accidents contain indicators of "unsafe conditions of the rules and regulations" with a frequency of 1590, accounting for 74.3% of the total frequency of 2140. "Unsafe behaviors of the operator" is another important contributory factor, which mainly includes "operator error" and "venturing into dangerous places." A systems analysis approach was applied by using structural equation modeling (SEM) to examine the interactions between the contributory factors of coal mine accidents. The analysis of results leads to three conclusions. (i) "Unsafe conditions of the rules and regulations," affect the "unsafe behaviors of the operator," "unsafe conditions of the equipment," and "unsafe conditions of the environment." (ii) The three influencing factors of coal mine accidents (with the frequency of effect relation in descending order) are "lack of safety education and training," "rules and regulations of safety production responsibility," and "rules and regulations of supervision and inspection." (iii) The three influenced factors (with the frequency in descending order) of coal mine accidents are "venturing into dangerous places," "poor workplace environment," and "operator error." Copyright © 2016 Elsevier Ltd. All rights reserved.

  9. An Accident Precursor Analysis Process Tailored for NASA Space Systems

    NASA Technical Reports Server (NTRS)

    Groen, Frank; Stamatelatos, Michael; Dezfuli, Homayoon; Maggio, Gaspare

    2010-01-01

    Accident Precursor Analysis (APA) serves as the bridge between existing risk modeling activities, which are often based on historical or generic failure statistics, and system anomalies, which provide crucial information about the failure mechanisms that are actually operative in the system and which may differ in frequency or type from those in the various models. These discrepancies between the models (perceived risk) and the system (actual risk) provide the leading indication of an underappreciated risk. This paper presents an APA process developed specifically for NASA Earth-to-Orbit space systems. The purpose of the process is to identify and characterize potential sources of system risk as evidenced by anomalous events which, although not necessarily presenting an immediate safety impact, may indicate that an unknown or insufficiently understood risk-significant condition exists in the system. Such anomalous events are considered accident precursors because they signal the potential for severe consequences that may occur in the future, due to causes that are discernible from their occurrence today. Their early identification allows them to be integrated into the overall system risk model used to intbrm decisions relating to safety.

  10. Road safety analysis on Achmad Yani frontage road Surabaya

    NASA Astrophysics Data System (ADS)

    Machsus; Prayogo, I.; Chomaedhi; Hayati, D. W.; Utanaka, A.

    2017-11-01

    This research discusses road safety analysis on the operation of frontage road on the west side of Achmad Yani Road Surabaya. This research began by conducting survey on secondary data of traffic accidents. In addition, primary data survey was conducted to obtain traffic data, geometric road data, and other supporting data at the study site along the west side frontage of Ahmad Yani Road Surabaya. Devices used in this research include camera, handy cam, speed gun, counters of vehicles, rolling meter, computer and others. In outline, the stages to conduct this research are divided into 4 stages, namely 1.the preparation stage, 2.data collection and processing, 3. analysis and discussion, and 4. conclusion. The results of this study showed that the accident characteristics of the frontage road are (i) 3 accidents occured per month, (ii) motorcycles was accounted for the largest proportion of accidents which amounted to 74.6 percent, (iii) there were 3 accident victims per month, and (iv) material losses per month worths 1.2 million. The accident rate in 2016 was 0.04 crashes per one million vehicle travels per kilometer, while during 2 months in 2017 it was 0.15 accidents per one million vehicle travels per kilometer. Black spot area of accident is located on Sta 2 + 800 to 2 + 900 which is in front of Graha Pena building and DBL Arena. The high rate of accidents is influenced by the speed of the vehicle which 85 percentile exceeds the speed limit of 40km per hour.

  11. An analysis of aircraft accidents involving fires

    NASA Technical Reports Server (NTRS)

    Lucha, G. V.; Robertson, M. A.; Schooley, F. A.

    1975-01-01

    All U. S. Air Carrier accidents between 1963 and 1974 were studied to assess the extent of total personnel and aircraft damage which occurred in accidents and in accidents involving fire. Published accident reports and NTSB investigators' factual backup files were the primary sources of data. Although it was frequently not possible to assess the relative extent of fire-caused damage versus impact damage using the available data, the study established upper and lower bounds for deaths and damage due specifically to fire. In 12 years there were 122 accidents which involved airframe fires. Eighty-seven percent of the fires occurred after impact, and fuel leakage from ruptured tanks or severed lines was the most frequently cited cause. A cost analysis was performed for 300 serious accidents, including 92 serious accidents which involved fire. Personal injury costs were outside the scope of the cost analysis, but data on personnel injury judgements as well as settlements received from the CAB are included for reference.

  12. Explorative spatial analysis of traffic accident statistics and road mortality among the provinces of Turkey.

    PubMed

    Erdogan, Saffet

    2009-10-01

    The aim of the study is to describe the inter-province differences in traffic accidents and mortality on roads of Turkey. Two different risk indicators were used to evaluate the road safety performance of the provinces in Turkey. These indicators are the ratios between the number of persons killed in road traffic accidents (1) and the number of accidents (2) (nominators) and their exposure to traffic risk (denominator). Population and the number of registered motor vehicles in the provinces were used as denominators individually. Spatial analyses were performed to the mean annual rate of deaths and to the number of fatal accidents that were calculated for the period of 2001-2006. Empirical Bayes smoothing was used to remove background noise from the raw death and accident rates because of the sparsely populated provinces and small number of accident and death rates of provinces. Global and local spatial autocorrelation analyses were performed to show whether the provinces with high rates of deaths-accidents show clustering or are located closer by chance. The spatial distribution of provinces with high rates of deaths and accidents was nonrandom and detected as clustered with significance of P<0.05 with spatial autocorrelation analyses. Regions with high concentration of fatal accidents and deaths were located in the provinces that contain the roads connecting the Istanbul, Ankara, and Antalya provinces. Accident and death rates were also modeled with some independent variables such as number of motor vehicles, length of roads, and so forth using geographically weighted regression analysis with forward step-wise elimination. The level of statistical significance was taken as P<0.05. Large differences were found between the rates of deaths and accidents according to denominators in the provinces. The geographically weighted regression analyses did significantly better predictions for both accident rates and death rates than did ordinary least regressions, as

  13. Analysis of accidents and injuries on motorcycles in Mexico.

    PubMed

    Berrones-Sanz, Luis David

    2017-01-01

    To analyze the type of injuries and the characteristics and geographical distribution of road accidents where motorcycles were involved in Mexico. A descriptive analysis of second-hand information sources was conducted, including the number of accidents (N = 41,881), total number of injured people (N = 13,916) and medical expenses (N = 9,111) associated to motorcycle accidents during 2014. Motorcycles represent 13.14% of the total number of deaths in road accidents in Mexico, and the Southeast region of Mexico registers the highest proportion of fatal injuries. Of the total number of motorcycles, 1.84% (95% confidence interval [CI]: 1.83-1.86) were involved in a collision. 3.64 (95% CI: 3.39-3.89) people died and 105.5 (95% CI: 104.1-106.8) were injured in every 10,000. Out of the total number of injuries, 76.6% were male and 53.74% were women. 55.1% of deaths were caused by intracranial trauma. Only 16.6% wore a helmet at the time of the accident, and those not wearing a helmet had a 2.11 (odds ratio [OR]: 2.1; CI 95%: 1.8-2.4) higher chance of head injury. Regarding the severity of the crash, those occurred in suburban areas (OR: 6.58; CI 95%: 5.69-7.60), in unpaved surfaces (OR: 4.13; CI 95%: 3.04-5.61), after low alcohol consumption (OR: 1.89; CI 95%: 1.46-2.44), at night (OR: 2.24; CI 95%: 1.95-2.57) and on weekends (OR: 1.65; CI 95%: 1.44-1.90), had the highest chance of turning into a fatal accident. In spite of the progress made in terms of road safety, motorcycle accidents are still increasing, and the use of a helmet is still proportionally low. More information on these groups and risk factors needs to be available so people are better informed. Also, regulations need improvements regarding the use of security equipment like helmets in order to reduce injuries and fatal accidents.

  14. The development of an inherent safety approach to the prevention of domino accidents.

    PubMed

    Cozzani, Valerio; Tugnoli, Alessandro; Salzano, Ernesto

    2009-11-01

    The severity of industrial accidents in which a domino effect takes place is well known in the chemical and process industry. The application of an inherent safety approach for the prevention of escalation events leading to domino accidents was explored in the present study. Reference primary scenarios were analyzed and escalation vectors were defined. Inherent safety distances were defined and proposed as a metric to express the intensity of the escalation vectors. Simple rules of thumb were presented for a preliminary screening of these distances. Swift reference indices for layout screening with respect to escalation hazard were also defined. Two case studies derived from existing layouts of oil refineries were selected to understand the potentialities coming from the application in the methodology. The results evidenced that the approach allows a first comparative assessment of the actual domino hazard in a layout, and the identification of critical primary units with respect to escalation events. The methodology developed also represents a useful screening tool to identify were to dedicate major efforts in the design of add-on measures, optimizing conventional passive and active measures for the prevention of severe domino accidents.

  15. Type A Accident Investigation Board report on the January 17, 1996, electrical accident with injury in Technical Area 21 Tritium Science and Fabrication Facility Los Alamos National Laboratory. Final report

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    NONE

    1996-04-01

    An electrical accident was investigated in which a crafts person received serious injuries as a result of coming into contact with a 13.2 kilovolt (kV) electrical cable in the basement of Building 209 in Technical Area 21 (TA-21-209) in the Tritium Science and Fabrication Facility (TSFF) at Los Alamos National Laboratory (LANL). In conducting its investigation, the Accident Investigation Board used various analytical techniques, including events and causal factor analysis, barrier analysis, change analysis, fault tree analysis, materials analysis, and root cause analysis. The board inspected the accident site, reviewed events surrounding the accident, conducted extensive interviews and document reviews,more » and performed causation analyses to determine the factors that contributed to the accident, including any management system deficiencies. Relevant management systems and factors that could have contributed to the accident were evaluated in accordance with the guiding principles of safety management identified by the Secretary of Energy in an October 1994 letter to the Defense Nuclear Facilities Safety Board and subsequently to Congress.« less

  16. A statistical analysis of the impact of advertising signs on road safety.

    PubMed

    Yannis, George; Papadimitriou, Eleonora; Papantoniou, Panagiotis; Voulgari, Chrisoula

    2013-01-01

    This research aims to investigate the impact of advertising signs on road safety. An exhaustive review of international literature was carried out on the effect of advertising signs on driver behaviour and safety. Moreover, a before-and-after statistical analysis with control groups was applied on several road sites with different characteristics in the Athens metropolitan area, in Greece, in order to investigate the correlation between the placement or removal of advertising signs and the related occurrence of road accidents. Road accident data for the 'before' and 'after' periods on the test sites and the control sites were extracted from the database of the Hellenic Statistical Authority, and the selected 'before' and 'after' periods vary from 2.5 to 6 years. The statistical analysis shows no statistical correlation between road accidents and advertising signs in none of the nine sites examined, as the confidence intervals of the estimated safety effects are non-significant at 95% confidence level. This can be explained by the fact that, in the examined road sites, drivers are overloaded with information (traffic signs, directions signs, labels of shops, pedestrians and other vehicles, etc.) so that the additional information load from advertising signs may not further distract them.

  17. Safety analysis report: A comparison of incidents from Safety Years 2006 through 2010, USDA Forest Service, Rocky Mountain Research Station Inventory and Monitoring Program

    Treesearch

    Devon Donahue

    2012-01-01

    This paper is an analysis of 5 years of accident data for the USDA Forest Service, Rocky Mountain Research Station (RMRS) Inventory and Monitoring (IM) Program that identifies past trends, allows for standardized self-comparison, and increases our understanding of the true costs of injuries and accidents. Measuring safety is a difficult task. While most agree that...

  18. Functional Safety of Hybrid Laser Safety Systems - How can a Combination between Passive and Active Components Prevent Accidents?

    NASA Astrophysics Data System (ADS)

    Lugauer, F. P.; Stiehl, T. H.; Zaeh, M. F.

    Modern laser systems are widely used in industry due to their excellent flexibility and high beam intensities. This leads to an increased hazard potential, because conventional laser safety barriers only offer a short protection time when illuminated with high laser powers. For that reason active systems are used more and more to prevent accidents with laser machines. These systems must fulfil the requirements of functional safety, e.g. according to IEC 61508, which causes high costs. The safety provided by common passive barriers is usually unconsidered in this context. In the presented approach, active and passive systems are evaluated from a holistic perspective. To assess the functional safety of hybrid safety systems, the failure probability of passive barriers is analysed and added to the failure probability of the active system.

  19. Analysis of Occupational Accidents in Underground and Surface Mining in Spain Using Data-Mining Techniques

    PubMed Central

    Sanmiquel, Lluís; Bascompta, Marc; Rossell, Josep M.; Anticoi, Hernán Francisco; Guash, Eduard

    2018-01-01

    An analysis of occupational accidents in the mining sector was conducted using the data from the Spanish Ministry of Employment and Social Safety between 2005 and 2015, and data-mining techniques were applied. Data was processed with the software Weka. Two scenarios were chosen from the accidents database: surface and underground mining. The most important variables involved in occupational accidents and their association rules were determined. These rules are composed of several predictor variables that cause accidents, defining its characteristics and context. This study exposes the 20 most important association rules in the sector—either surface or underground mining—based on the statistical confidence levels of each rule as obtained by Weka. The outcomes display the most typical immediate causes, along with the percentage of accidents with a basis in each association rule. The most important immediate cause is body movement with physical effort or overexertion, and the type of accident is physical effort or overexertion. On the other hand, the second most important immediate cause and type of accident are different between the two scenarios. Data-mining techniques were chosen as a useful tool to find out the root cause of the accidents. PMID:29518921

  20. Analysis of Occupational Accidents in Underground and Surface Mining in Spain Using Data-Mining Techniques.

    PubMed

    Sanmiquel, Lluís; Bascompta, Marc; Rossell, Josep M; Anticoi, Hernán Francisco; Guash, Eduard

    2018-03-07

    An analysis of occupational accidents in the mining sector was conducted using the data from the Spanish Ministry of Employment and Social Safety between 2005 and 2015, and data-mining techniques were applied. Data was processed with the software Weka. Two scenarios were chosen from the accidents database: surface and underground mining. The most important variables involved in occupational accidents and their association rules were determined. These rules are composed of several predictor variables that cause accidents, defining its characteristics and context. This study exposes the 20 most important association rules in the sector-either surface or underground mining-based on the statistical confidence levels of each rule as obtained by Weka. The outcomes display the most typical immediate causes, along with the percentage of accidents with a basis in each association rule. The most important immediate cause is body movement with physical effort or overexertion, and the type of accident is physical effort or overexertion. On the other hand, the second most important immediate cause and type of accident are different between the two scenarios. Data-mining techniques were chosen as a useful tool to find out the root cause of the accidents.

  1. A Flexible Hierarchical Bayesian Modeling Technique for Risk Analysis of Major Accidents.

    PubMed

    Yu, Hongyang; Khan, Faisal; Veitch, Brian

    2017-09-01

    Safety analysis of rare events with potentially catastrophic consequences is challenged by data scarcity and uncertainty. Traditional causation-based approaches, such as fault tree and event tree (used to model rare event), suffer from a number of weaknesses. These include the static structure of the event causation, lack of event occurrence data, and need for reliable prior information. In this study, a new hierarchical Bayesian modeling based technique is proposed to overcome these drawbacks. The proposed technique can be used as a flexible technique for risk analysis of major accidents. It enables both forward and backward analysis in quantitative reasoning and the treatment of interdependence among the model parameters. Source-to-source variability in data sources is also taken into account through a robust probabilistic safety analysis. The applicability of the proposed technique has been demonstrated through a case study in marine and offshore industry. © 2017 Society for Risk Analysis.

  2. Investigations on optimization of accident management measures following a station blackout accident in a VVER-1000 pressurized water reactor

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Tusheva, P.; Schaefer, F.; Kliem, S.

    2012-07-01

    The reactor safety issues are of primary importance for preserving the health of the population and ensuring no release of radioactivity and fission products into the environment. A part of the nuclear research focuses on improvement of the safety of existing nuclear power plants. Studies, research and efforts are a continuing process at improving the safety and reliability of existing and newly developed nuclear power plants at prevention of a core melt accident. Station blackout (loss of AC power supply) is one of the dominant accidents taken into consideration at performing accident analysis. In case of multiple failures of safetymore » systems it leads to a severe accident. To prevent an accident to turn into a severe one or to mitigate the consequences, accident management measures must be performed. The present paper outlines possibilities for application and optimization of accident management measures following a station blackout accident. Assessed is the behaviour of the nuclear power plant during a station blackout accident without accident management measures and with application of primary/secondary side oriented accident management measures. Discussed are the possibilities for operators ' intervention and the influence of the performed accident management measures on the course of the accident. Special attention has been paid to the effectiveness of the passive feeding and physical phenomena having an influence on the system behaviour. The performed simulations show that the effectiveness of the secondary side feeding procedure can be limited due to an early evaporation or flashing effects in the feed water system. The analyzed cases show that the effectiveness of the accident management measures strongly depends on the initiation criteria applied for depressurization of the reactor coolant system. (authors)« less

  3. Effect of Occupational Health and Safety Management System on Work-Related Accident Rate and Differences of Occupational Health and Safety Management System Awareness between Managers in South Korea's Construction Industry

    PubMed Central

    Yoon, Seok J.; Lin, Hsing K.; Chen, Gang; Yi, Shinjea; Choi, Jeawook; Rui, Zhenhua

    2013-01-01

    Background The study was conducted to investigate the current status of the occupational health and safety management system (OHSMS) in the construction industry and the effect of OHSMS on accident rates. Differences of awareness levels on safety issues among site general managers and occupational health and safety (OHS) managers are identified through surveys. Methods The accident rates for the OHSMS-certified construction companies from 2006 to 2011, when the construction OHSMS became widely available, were analyzed to understand the effect of OHSMS on the work-related injury rates in the construction industry. The Korea Occupational Safety and Health Agency 18001 is the certification to these companies performing OHSMS in South Korea. The questionnaire was created to analyze the differences of OHSMS awareness between site general managers and OHS managers of construction companies. Results The implementation of OHSMS among the top 100 construction companies in South Korea shows that the accident rate decreased by 67% and the fatal accident rate decreased by 10.3% during the period from 2006 to 2011. The survey in this study shows different OHSMS awareness levels between site general managers and OHS managers. The differences were motivation for developing OHSMS, external support needed for implementing OHSMS, problems and effectiveness of implementing OHSMS. Conclusion Both work-related accident and fatal accident rates were found to be significantly reduced by implementing OHSMS in this study. The differences of OHSMS awareness between site general managers and OHS managers were identified through a survey. The effect of these differences on safety and other benefits warrants further research with proper data collection. PMID:24422176

  4. Effect of Occupational Health and Safety Management System on Work-Related Accident Rate and Differences of Occupational Health and Safety Management System Awareness between Managers in South Korea's Construction Industry.

    PubMed

    Yoon, Seok J; Lin, Hsing K; Chen, Gang; Yi, Shinjea; Choi, Jeawook; Rui, Zhenhua

    2013-12-01

    The study was conducted to investigate the current status of the occupational health and safety management system (OHSMS) in the construction industry and the effect of OHSMS on accident rates. Differences of awareness levels on safety issues among site general managers and occupational health and safety (OHS) managers are identified through surveys. The accident rates for the OHSMS-certified construction companies from 2006 to 2011, when the construction OHSMS became widely available, were analyzed to understand the effect of OHSMS on the work-related injury rates in the construction industry. The Korea Occupational Safety and Health Agency 18001 is the certification to these companies performing OHSMS in South Korea. The questionnaire was created to analyze the differences of OHSMS awareness between site general managers and OHS managers of construction companies. The implementation of OHSMS among the top 100 construction companies in South Korea shows that the accident rate decreased by 67% and the fatal accident rate decreased by 10.3% during the period from 2006 to 2011. The survey in this study shows different OHSMS awareness levels between site general managers and OHS managers. The differences were motivation for developing OHSMS, external support needed for implementing OHSMS, problems and effectiveness of implementing OHSMS. Both work-related accident and fatal accident rates were found to be significantly reduced by implementing OHSMS in this study. The differences of OHSMS awareness between site general managers and OHS managers were identified through a survey. The effect of these differences on safety and other benefits warrants further research with proper data collection.

  5. 49 CFR 195.50 - Reporting accidents.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Reporting accidents. 195.50 Section 195.50 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY... PIPELINE Annual, Accident, and Safety-Related Condition Reporting § 195.50 Reporting accidents. An accident...

  6. 49 CFR 195.50 - Reporting accidents.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Reporting accidents. 195.50 Section 195.50 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY... PIPELINE Annual, Accident, and Safety-Related Condition Reporting § 195.50 Reporting accidents. An accident...

  7. RELAP5 Application to Accident Analysis of the NIST Research Reactor

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Baek, J.; Cuadra Gascon, A.; Cheng, L.Y.

    Detailed safety analyses have been performed for the 20 MW D{sub 2}O moderated research reactor (NBSR) at the National Institute of Standards and Technology (NIST). The time-dependent analysis of the primary system is determined with a RELAP5 transient analysis model that includes the reactor vessel, the pump, heat exchanger, fuel element geometry, and flow channels for both the six inner and twenty-four outer fuel elements. A post-processing of the simulation results has been conducted to evaluate minimum critical heat flux ratio (CHFR) using the Sudo-Kaminaga correlation. Evaluations are performed for the following accidents: (1) the control rod withdrawal startup accidentmore » and (2) the maximum reactivity insertion accident. In both cases the RELAP5 results indicate that there is adequate margin to CHF and no damage to the fuel will occur because of sufficient coolant flow through the fuel channels and the negative scram reactivity insertion.« less

  8. Duty of Notification and Aviation Safety-A Study of Fatal Aviation Accidents in the United States in 2015.

    PubMed

    Vuorio, Alpo; Budowle, Bruce; Sajantila, Antti; Laukkala, Tanja; Junttila, Ilkka; Kravik, Stein E; Griffiths, Robin

    2018-06-13

    After the Germanwings accident, the French Safety Investigation Authority (BEA) recommended that the World Health Organization (WHO) and European Community (EC) develop clear rules for the duty of notification process. Aeromedical practitioners (AMEs) face a dilemma when considering the duty of notification and conflicts between pilot privacy and public and third-party safety. When balancing accountability, knowledge of the duty of notification process, legislation and the clarification of a doctor’s own set of values should be assessed a priori. Relatively little is known of the magnitude of this problem in aviation safety. To address this, the National Transportation Safety Board (NTSB) database was searched to identify fatal accidents during 2015 in the United States in which a deceased pilot used a prescribed medication or had a disease that potentially reduced pilot performance and was not reported to the AME. Altogether, 202 finalized accident reports with toxicology were available from (the year) 2015. In 5% (10/202) of these reports, the pilot had either a medication or a disease not reported to an AME which according to the accident investigation was causal to the fatal accident. In addition, the various approaches to duty of notification in aviation in New Zealand, Finland and Norway are discussed. The process of notification of authorities without a pilot’s express permission needs to be carried out by using a guidance protocol that works within legislation and professional responsibilities to address the pilot and the public, as well as the healthcare provider. Professional guidance defining this duty of notification is urgently needed.

  9. Safety training priorities

    NASA Astrophysics Data System (ADS)

    Thompson, N. A.; Ruck, H. W.

    1984-04-01

    The Air Force is interested in identifying potentially hazardous tasks and prevention of accidents. This effort proposes four methods for determining safety training priorities for job tasks in three enlisted specialties. These methods can be used to design training aimed at avoiding loss of people, time, materials, and money associated with on-the-job accidents. Job tasks performed by airmen were measured using task and job factor ratings. Combining accident reports and job inventories, subject-matter experts identified tasks associated with accidents over a 3-year period. Applying correlational, multiple regression, and cost-benefit analysis, four methods were developed for ordering hazardous tasks to determine safety training priorities.

  10. Indonesian railway accidents--utilizing Human Factors Analysis and Classification System in determining potential contributing factors.

    PubMed

    Iridiastadi, Hardianto; Ikatrinasari, Zulfa Fitri

    2012-01-01

    The prevalence of Indonesian railway accidents has not been declining, with hundreds of fatalities reported in the past decade. As an effort to help the National Transportation Safety Committee (NTSC), this study was conducted that aimed at understanding factors that might have contributed to the accidents. Human Factors Analysis and Classification System (HFACS) was utilized for this purpose. A total of nine accident reports (provided by the Indonesian NTSC) involving fatalities were studied using the technique. Results of this study indicated 72 factors that were closely related to the accidents. Of these, roughly 22% were considered as operator acts while about 39% were related to preconditions for operator acts. Supervisory represented 14% of the factors, and the remaining (about 25%) were associated with organizational factors. It was concluded that, while train drivers indeed played an important role in the accidents, interventions solely directed toward train drivers may not be adequate. A more comprehensive approach in minimizing the accidents should be conducted that addresses all the four aspects of HFACS.

  11. Potential safety benefits of intelligent cruise control systems.

    PubMed

    Chira-Chavala, T; Yoo, S M

    1994-04-01

    Potential safety impact of a hypothetical intelligent cruise control system (ICCS) is evaluated in terms of changes in traffic accidents and some traffic operation characteristics affecting safety. The analysis of changes in traffic accidents is accomplished by in-depth examinations of police accident reports for four major counties in California. The evaluation of changes in traffic operation characteristics affecting safety is accomplished by vehicle simulation. The accident analysis reveals that the use of the hypothetical ICCS could potentially reduce traffic accidents by up to 7.5%. Preliminary vehicle simulation results based on a 10-vehicle convoy indicate that the use of the hypothetical ICCS could reduce frequencies of hard acceleration and deceleration, enhance speed harmonization among vehicles, and reduce incidence of "less-safe" headway.

  12. Safety Education. A Guide To Help Prevent Accidents Associated with the Home, Student Transportation, Disasters, Pedestrians, Passengers, Fires, Consumerism, Recreation.

    ERIC Educational Resources Information Center

    Texas Education Agency, Austin.

    This teacher's guide presents 10 instructional units for one portion of the Texas-approved course in driver and safety education. The units cover the following topics: what is safety?; accident causation and prevention; home safety; student transportation safety; disasters; pedestrian safety; passenger safety; fire safety; consumer safety; and…

  13. Risk of Occupational Accidents in Workers with Obstructive Sleep Apnea: Systematic Review and Meta-analysis

    PubMed Central

    Garbarino, Sergio; Guglielmi, Ottavia; Sanna, Antonio; Mancardi, Gian Luigi; Magnavita, Nicola

    2016-01-01

    Study Objectives: Obstructive sleep apnea (OSA) is the single most important preventable medical cause of excessive daytime sleepiness (EDS) and driving accidents. OSA may also adversely affect work performance through a decrease in productivity, and an increase in the injury rate. Nevertheless, no systematic review and meta-analysis of the relationship between OSA and work accidents has been performed thus far. Methods: PubMed, PsycInfo, Scopus, Web of Science, and Cochrane Library were searched. Out of an initial list of 1,099 papers, 10 studies (12,553 participants) were eligible for our review, and 7 of them were included in the meta-analysis. The overall effects were measured by odds ratios (OR) and 95% confidence intervals (CI). An assessment was made of the methodological quality of the studies. Moderator analysis and funnel plot analysis were used to explore the sources of between-study heterogeneity. Results: Compared to controls, the odds of work accident was found to be nearly double in workers with OSA (OR = 2.18; 95% CI = 1.53–3.10). Occupational driving was associated with a higher effect size. Conclusions: OSA is an underdiagnosed nonoccupational disease that has a strong adverse effect on work accidents. The nearly twofold increased odds of work accidents in subjects with OSA calls for workplace screening in selected safety-sensitive occupations. Commentary: A commentary on this article appears in this issue on page 1171. Citation: Garbarino S, Guglielmi O, Sanna A, Mancardi GL, Magnavita N. Risk of occupational accidents in workers with obstructive sleep apnea: systematic review and meta-analysis. SLEEP 2016;39(6):1211–1218. PMID:26951401

  14. Environmental health, public safety, and social impacts associated with transportation accidents involving hazardous substances

    DOT National Transportation Integrated Search

    2000-12-31

    Accidents involving chemicals or radioactive materials represent a significant threat to the environment, public : health and safety, and community well-being. In an increasingly complex and interconnected world, no community : is immune from the thr...

  15. Aircraft Loss-of-Control Accident Analysis

    NASA Technical Reports Server (NTRS)

    Belcastro, Christine M.; Foster, John V.

    2010-01-01

    Loss of control remains one of the largest contributors to fatal aircraft accidents worldwide. Aircraft loss-of-control accidents are complex in that they can result from numerous causal and contributing factors acting alone or (more often) in combination. Hence, there is no single intervention strategy to prevent these accidents. To gain a better understanding into aircraft loss-of-control events and possible intervention strategies, this paper presents a detailed analysis of loss-of-control accident data (predominantly from Part 121), including worst case combinations of causal and contributing factors and their sequencing. Future potential risks are also considered.

  16. Analysis of Crew Fatigue in AIA Guantanamo Bay Aviation Accident

    NASA Technical Reports Server (NTRS)

    Rosekind, Mark R.; Gregory, Kevin B.; Miller, Donna L.; Co, Elizabeth L.; Lebacqz, J. Victor; Statler, Irving C. (Technical Monitor)

    1994-01-01

    Flight operations can engender fatigue, which can affect flight crew performance, vigilance, and mood. The National Transportation Safety Board (NTSB) requested the NASA Fatigue Countermeasures Program to analyze crew fatigue factors in an aviation accident that occurred at Guantanamo Bay, Cuba. There are specific fatigue factors that can be considered in such investigations: cumulative sleep loss, continuous hours of wakefulness prior to the incident or accident, and the time of day at which the accident occurred. Data from the NTSB Human Performance Investigator's Factual Report, the Operations Group Chairman's Factual Report, and the Flight 808 Crew Statements were analyzed, using conservative estimates and averages to reconcile discrepancies among the sources. Analysis of these data determined the following: the entire crew displayed cumulative sleep loss, operated during an extended period of continuous wakefulness, and obtained sleep at times in opposition to the circadian disposition for sleep, and that the accident occurred in the afternoon window of physiological sleepiness. In addition to these findings, evidence that fatigue affected performance was suggested by the cockpit voice recorder (CVR) transcript as well as in the captain's testimony. Examples from the CVR showed degraded decision-making skills, fixation, and slowed responses, all of which can be affected by fatigue; also, the captain testified to feeling "lethargic and indifferent" just prior to the accident. Therefore, the sleep/wake history data supports the hypothesis that fatigue was a factor that affected crewmembers' performance. Furthermore, the examples from the CVR and the captain's testimony support the hypothesis that the fatigue had an impact on specific actions involved in the occurrence of the accident.

  17. United States Department of Energy severe accident research following the Fukushima Daiichi accidents

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Farmer, M. T.; Corradini, M.; Rempe, J.

    The U.S. Department of Energy (DOE) has played a major role in the U.S. response to the events at Fukushima Daiichi. During the first several weeks following the accident, U.S. assistance efforts were guided by results from a significant and diverse set of analyses. In the months that followed, a coordinated analysis activity aimed at gaining a more thorough understanding of the accident sequence was completed using laboratory-developed, system-level best-estimate accident analysis codes, while a parallel analysis was conducted by U.S. industry. A comparison of predictions for Unit 1 from these two studies indicated significant differences between MAAP and MELCORmore » results for key plant parameters, such as in-core hydrogen production. On that basis, a crosswalk was completed to determine the key modeling variations that led to these differences. In parallel with these activities, it became clear that there was a need to perform a technology gap evaluation on accident-tolerant components and severe accident analysis methodologies with the goal of identifying any data and/or knowledge gaps that may exist given the current state of light water reactor (LWR) severe accident research and augmented by insights from Fukushima. In addition, there is growing international recognition that data from Fukushima could significantly reduce uncertainties related to severe accident progression, particularly for boiling water reactors. On these bases, a group of U. S. experts in LWR safety and plant operations was convened by the DOE Office of Nuclear Energy (DOE-NE) to complete technology gap analysis and Fukushima forensics data needs identification activities. The results from these activities were used as the basis for refining DOE-NE's severe accident research and development (R&D) plan. Finally, this paper provides a high-level review of DOE-sponsored R&D efforts in these areas, including planned activities on accident-tolerant components and accident analysis methods.« less

  18. United States Department of Energy severe accident research following the Fukushima Daiichi accidents

    DOE PAGES

    Farmer, M. T.; Corradini, M.; Rempe, J.; ...

    2016-11-02

    The U.S. Department of Energy (DOE) has played a major role in the U.S. response to the events at Fukushima Daiichi. During the first several weeks following the accident, U.S. assistance efforts were guided by results from a significant and diverse set of analyses. In the months that followed, a coordinated analysis activity aimed at gaining a more thorough understanding of the accident sequence was completed using laboratory-developed, system-level best-estimate accident analysis codes, while a parallel analysis was conducted by U.S. industry. A comparison of predictions for Unit 1 from these two studies indicated significant differences between MAAP and MELCORmore » results for key plant parameters, such as in-core hydrogen production. On that basis, a crosswalk was completed to determine the key modeling variations that led to these differences. In parallel with these activities, it became clear that there was a need to perform a technology gap evaluation on accident-tolerant components and severe accident analysis methodologies with the goal of identifying any data and/or knowledge gaps that may exist given the current state of light water reactor (LWR) severe accident research and augmented by insights from Fukushima. In addition, there is growing international recognition that data from Fukushima could significantly reduce uncertainties related to severe accident progression, particularly for boiling water reactors. On these bases, a group of U. S. experts in LWR safety and plant operations was convened by the DOE Office of Nuclear Energy (DOE-NE) to complete technology gap analysis and Fukushima forensics data needs identification activities. The results from these activities were used as the basis for refining DOE-NE's severe accident research and development (R&D) plan. Finally, this paper provides a high-level review of DOE-sponsored R&D efforts in these areas, including planned activities on accident-tolerant components and accident analysis methods.« less

  19. Combining task analysis and fault tree analysis for accident and incident analysis: a case study from Bulgaria.

    PubMed

    Doytchev, Doytchin E; Szwillus, Gerd

    2009-11-01

    Understanding the reasons for incident and accident occurrence is important for an organization's safety. Different methods have been developed to achieve this goal. To better understand the human behaviour in incident occurrence we propose an analysis concept that combines Fault Tree Analysis (FTA) and Task Analysis (TA). The former method identifies the root causes of an accident/incident, while the latter analyses the way people perform the tasks in their work environment and how they interact with machines or colleagues. These methods were complemented with the use of the Human Error Identification in System Tools (HEIST) methodology and the concept of Performance Shaping Factors (PSF) to deepen the insight into the error modes of an operator's behaviour. HEIST shows the external error modes that caused the human error and the factors that prompted the human to err. To show the validity of the approach, a case study at a Bulgarian Hydro power plant was carried out. An incident - the flooding of the plant's basement - was analysed by combining the afore-mentioned methods. The case study shows that Task Analysis in combination with other methods can be applied successfully to human error analysis, revealing details about erroneous actions in a realistic situation.

  20. How Past Loss of Control Accidents May Inform Safety Cases for Advanced Control Systems on Commercial Aircraft

    NASA Technical Reports Server (NTRS)

    Holloway, C. M.; Johnson, C. W.

    2008-01-01

    This paper describes five loss of control accidents involving commercial aircraft, and derives from those accidents three principles to consider when developing a potential safety case for an advanced flight control system for commercial aircraft. One, among the foundational evidence needed to support a safety case is the availability to the control system of accurate and timely information about the status and health of relevant systems and components. Two, an essential argument to be sustained in the safety case is that pilots are provided with adequate information about the control system to enable them to understand the capabilities that it provides. Three, another essential argument is that the advanced control system will not perform less safely than a good pilot.

  1. Off-road truck-related accidents in U.S. mines.

    PubMed

    Dindarloo, Saeid R; Pollard, Jonisha P; Siami-Irdemoosa, Elnaz

    2016-09-01

    Off-road trucks are one of the major sources of equipment-related accidents in the U.S. mining industries. A systematic analysis of all off-road truck-related accidents, injuries, and illnesses, which are reported and published by the Mine Safety and Health Administration (MSHA), is expected to provide practical insights for identifying the accident patterns and trends in the available raw database. Therefore, appropriate safety management measures can be administered and implemented based on these accident patterns/trends. A hybrid clustering-classification methodology using K-means clustering and gene expression programming (GEP) is proposed for the analysis of severe and non-severe off-road truck-related injuries at U.S. mines. Using the GEP sub-model, a small subset of the 36 recorded attributes was found to be correlated to the severity level. Given the set of specified attributes, the clustering sub-model was able to cluster the accident records into 5 distinct groups. For instance, the first cluster contained accidents related to minerals processing mills and coal preparation plants (91%). More than two-thirds of the victims in this cluster had less than 5years of job experience. This cluster was associated with the highest percentage of severe injuries (22 severe accidents, 3.4%). Almost 50% of all accidents in this cluster occurred at stone operations. Similarly, the other four clusters were characterized to highlight important patterns that can be used to determine areas of focus for safety initiatives. The identified clusters of accidents may play a vital role in the prevention of severe injuries in mining. Further research into the cluster attributes and identified patterns will be necessary to determine how these factors can be mitigated to reduce the risk of severe injuries. Analyzing injury data using data mining techniques provides some insight into attributes that are associated with high accuracies for predicting injury severity. Copyright © 2016

  2. Safety analysts training

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Bolton, P.

    The purpose of this task was to support ESH-3 in providing Airborne Release Fraction and Respirable Fraction training to safety analysts at LANL who perform accident analysis, hazard analysis, safety analysis, and/or risk assessments at nuclear facilities. The task included preparation of materials for and the conduct of two 3-day training courses covering the following topics: safety analysis process; calculation model; aerosol physic concepts for safety analysis; and overview of empirically derived airborne release fractions and respirable fractions.

  3. Aircraft accidents : method of analysis

    NASA Technical Reports Server (NTRS)

    1929-01-01

    This report on a method of analysis of aircraft accidents has been prepared by a special committee on the nomenclature, subdivision, and classification of aircraft accidents organized by the National Advisory Committee for Aeronautics in response to a request dated February 18, 1928, from the Air Coordination Committee consisting of the Assistant Secretaries for Aeronautics in the Departments of War, Navy, and Commerce. The work was undertaken in recognition of the difficulty of drawing correct conclusions from efforts to analyze and compare reports of aircraft accidents prepared by different organizations using different classifications and definitions. The air coordination committee's request was made "in order that practices used may henceforth conform to a standard and be universally comparable." the purpose of the special committee therefore was to prepare a basis for the classification and comparison of aircraft accidents, both civil and military. (author)

  4. [Analysis of accidents for magnetically induced displacement of the large ferromagnetic material in magnetic resonance systems].

    PubMed

    Yamatani, Yuya; Doi, Tsukasa; Ueyama, Tsuyoshi; Nishiki, Shigeo; Ogura, Akio; Kawamitsu, Hideaki; Tsuchihashi, Toshio; Okuaki, Tomoyuki; Matsuda, Tsuyoshi

    2013-01-01

    To improve magnetic resonance (MR) safety, we surveyed the accidents caused by large ferromagnetic materials brought into MR systems accidentally. We sent a questionnaire to 700 Japanese medical institutions and received 405 valid responses (58%). A total of 97 accidents in 77 institutions were observed and we analyzed them regarding incidental rate, the detail situation and environmental factors. The mean accident rate of each institute was 0.7/100,000 examinations, which was widely distributed (0-25.6/100,000) depending on the institute. In this survey, relatively small institutes with less than 500 beds tend to have these accidents more frequently (p<0.01). The institutes in which daily MR examination counts are more than 10 patients have fewer accidents than those with less than 10 daily examinations. The institutes with 6-10 MR examinations daily have significantly more accidents than that with more than 10 daily MR examinations (p<0.01). The main mental factors of the accidents were considered to be "prejudice" and "carelessness" but some advocate "ignorance." Though we could not find significant reduction in the institutes that have lectures and training for MR safety, we should continue lectures and training for MR safety to reduce accidents due to "ignorance."

  5. Safety in the skies : personnel and parties in NTSB aviation accident investigations : master volume

    DOT National Transportation Integrated Search

    2001-01-01

    Recent high-profile commercial aviation mishaps have stretched the National Transportation Safety Board's (NTSB) resources to the limit and are testing the agency's ability to unravel the sorts of complex failures that lead to tragic accidents. In re...

  6. Application of forensic image analysis in accident investigations.

    PubMed

    Verolme, Ellen; Mieremet, Arjan

    2017-09-01

    Forensic investigations are primarily meant to obtain objective answers that can be used for criminal prosecution. Accident analyses are usually performed to learn from incidents and to prevent similar events from occurring in the future. Although the primary goal may be different, the steps in which information is gathered, interpreted and weighed are similar in both types of investigations, implying that forensic techniques can be of use in accident investigations as well. The use in accident investigations usually means that more information can be obtained from the available information than when used in criminal investigations, since the latter require a higher evidence level. In this paper, we demonstrate the applicability of forensic techniques for accident investigations by presenting a number of cases from one specific field of expertise: image analysis. With the rapid spread of digital devices and new media, a wealth of image material and other digital information has become available for accident investigators. We show that much information can be distilled from footage by using forensic image analysis techniques. These applications show that image analysis provides information that is crucial for obtaining the sequence of events and the two- and three-dimensional geometry of an accident. Since accident investigation focuses primarily on learning from accidents and prevention of future accidents, and less on the blame that is crucial for criminal investigations, the field of application of these forensic tools may be broader than would be the case in purely legal sense. This is an important notion for future accident investigations. Copyright © 2017 Elsevier B.V. All rights reserved.

  7. An analysis of pilot error-related aircraft accidents

    NASA Technical Reports Server (NTRS)

    Kowalsky, N. B.; Masters, R. L.; Stone, R. B.; Babcock, G. L.; Rypka, E. W.

    1974-01-01

    A multidisciplinary team approach to pilot error-related U.S. air carrier jet aircraft accident investigation records successfully reclaimed hidden human error information not shown in statistical studies. New analytic techniques were developed and applied to the data to discover and identify multiple elements of commonality and shared characteristics within this group of accidents. Three techniques of analysis were used: Critical element analysis, which demonstrated the importance of a subjective qualitative approach to raw accident data and surfaced information heretofore unavailable. Cluster analysis, which was an exploratory research tool that will lead to increased understanding and improved organization of facts, the discovery of new meaning in large data sets, and the generation of explanatory hypotheses. Pattern recognition, by which accidents can be categorized by pattern conformity after critical element identification by cluster analysis.

  8. The influence of economic incentives linked to road safety indicators on accidents: the case of toll concessions in Spain.

    PubMed

    Rangel, Thais; Vassallo, José Manuel; Herraiz, Israel

    2013-10-01

    The goal of this paper is to evaluate whether the incentives incorporated in toll highway concession contracts in order to encourage private operators to adopt measures to reduce accidents are actually effective at improving safety. To this end, we implemented negative binomial regression models using information about highway characteristics and accident data from toll highway concessions in Spain from 2007 to 2009. Our results show that even though road safety is highly influenced by variables that are not managed by the contractor, such as the annual average daily traffic (AADT), the percentage of heavy vehicles on the highway, number of lanes, number of intersections and average speed; the implementation of these incentives has a positive influence on the reduction of accidents and injuries. Consequently, this measure seems to be an effective way of improving safety performance in road networks. Copyright © 2013 Elsevier Ltd. All rights reserved.

  9. Accidents of Electrical and Mechanical Works for Public Sector Projects in Hong Kong.

    PubMed

    Wong, Francis K W; Chan, Albert P C; Wong, Andy K D; Hon, Carol K H; Choi, Tracy N Y

    2018-03-10

    A study on electrical and mechanical (E&M) works-related accidents for public sector projects provided the opportunity to gain a better understanding of the causes of accidents by analyzing the circumstances of all E&M works accidents. The research aims to examine accidents of E&M works which happened in public sector projects. A total of 421 E&M works-related accidents in the "Public Works Programme Construction Site Safety and Environmental Statistics" (PCSES) system were extracted for analysis. Two-step cluster analysis was conducted to classify the E&M accidents into different groups. The results identified three E&M accidents groups: (1) electricians with over 15 years of experience were prone to 'fall of person from height'; (2) electricians with zero to five years of experience were prone to 'slip, trip or fall on same level'; (3) air-conditioning workers with zero to five years of experience were prone to multiple types of accidents. Practical measures were recommended for each specific cluster group to avoid recurrence of similar accidents. The accident analysis would be vital for industry practitioners to enhance the safety performance of public sector projects. This study contributes to filling the knowledge gap of how and why E&M accidents occur and promulgating preventive measures for E&M accidents which have been under researched.

  10. Accidents of Electrical and Mechanical Works for Public Sector Projects in Hong Kong

    PubMed Central

    Wong, Francis K. W.; Chan, Albert P. C.; Wong, Andy K. D.; Choi, Tracy N. Y.

    2018-01-01

    A study on electrical and mechanical (E&M) works-related accidents for public sector projects provided the opportunity to gain a better understanding of the causes of accidents by analyzing the circumstances of all E&M works accidents. The research aims to examine accidents of E&M works which happened in public sector projects. A total of 421 E&M works-related accidents in the “Public Works Programme Construction Site Safety and Environmental Statistics” (PCSES) system were extracted for analysis. Two-step cluster analysis was conducted to classify the E&M accidents into different groups. The results identified three E&M accidents groups: (1) electricians with over 15 years of experience were prone to ‘fall of person from height’; (2) electricians with zero to five years of experience were prone to ‘slip, trip or fall on same level’; (3) air-conditioning workers with zero to five years of experience were prone to multiple types of accidents. Practical measures were recommended for each specific cluster group to avoid recurrence of similar accidents. The accident analysis would be vital for industry practitioners to enhance the safety performance of public sector projects. This study contributes to filling the knowledge gap of how and why E&M accidents occur and promulgating preventive measures for E&M accidents which have been under researched. PMID:29534429

  11. A multi-agent safety response model in the construction industry.

    PubMed

    Meliá, José L

    2015-01-01

    The construction industry is one of the sectors with the highest accident rates and the most serious accidents. A multi-agent safety response approach allows a useful diagnostic tool in order to understand factors affecting risk and accidents. The special features of the construction sector can influence the relationships among safety responses along the model of safety influences. The purpose of this paper is to test a model explaining risk and work-related accidents in the construction industry as a result of the safety responses of the organization, the supervisors, the co-workers and the worker. 374 construction employees belonging to 64 small Spanish construction companies working for two main companies participated in the study. Safety responses were measured using a 45-item Likert-type questionnaire. The structure of the measure was analyzed using factor analysis and the model of effects was tested using a structural equation model. Factor analysis clearly identifies the multi-agent safety dimensions hypothesized. The proposed safety response model of work-related accidents, involving construction specific results, showed a good fit. The multi-agent safety response approach to safety climate is a useful framework for the assessment of organizational and behavioral risks in construction.

  12. A Longitudinal Analysis of the Causal Factors in Major Maritime Accidents in the USA and Canada (1996-2006)

    NASA Technical Reports Server (NTRS)

    Johnson, C. W.; Holloway, C, M.

    2007-01-01

    Accident reports provide important insights into the causes and contributory factors leading to particular adverse events. In contrast, this paper provides an analysis that extends across the findings presented over ten years investigations into maritime accidents by both the US National Transportation Safety Board (NTSB) and Canadian Transportation Safety Board (TSB). The purpose of the study was to assess the comparative frequency of a range of causal factors in the reporting of adverse events. In order to communicate our findings, we introduce J-H graphs as a means of representing the proportion of causes and contributory factors associated with human error, equipment failure and other high level classifications in longitudinal studies of accident reports. Our results suggest the proportion of causal and contributory factors attributable to direct human error may be very much smaller than has been suggested elsewhere in the human factors literature. In contrast, more attention should be paid to wider systemic issues, including the managerial and regulatory context of maritime operations.

  13. Aviation safety and maintenance under major organizational changes, investigating non-existing accidents.

    PubMed

    Herrera, Ivonne A; Nordskag, Arve O; Myhre, Grete; Halvorsen, Kåre

    2009-11-01

    The objective of this paper is to discuss the following questions: Do concurrent organizational changes have a direct impact on aviation maintenance and safety, if so, how can this be measured? These questions were part of the investigation carried out by the Accident Investigation Board, Norway (AIBN). The AIBN investigated whether Norwegian aviation safety had been affected due to major organizational changes between 2000 and 2004. The main concern was the reduction in safety margins and its consequences. This paper presents a summary of the techniques used and explains how they were applied in three airlines and by two offshore helicopter operators. The paper also discusses the development of safety related indicators in the aviation industry. In addition, there is a summary of the lessons learned and safety recommendations. The Norwegian Ministry of Transport has required all players in the aviation industry to follow up the findings and recommendations of the AIBN study.

  14. Preventing accidents

    DOT National Transportation Integrated Search

    2005-08-01

    As the most effective strategy for improving safety is to prevent accidents from occurring at all, the Volpe Center applies a broad range of research techniques and capabilities to determine causes and consequences of accidents and to identify, asses...

  15. Safety I-II, resilience and antifragility engineering: a debate explained through an accident occurring on a mobile elevating work platform.

    PubMed

    Martinetti, Alberto; Chatzimichailidou, Maria Mikela; Maida, Luisa; van Dongen, Leo

    2018-04-24

    Occupational health and safety (OHS) represents an important field of exploration for the research community: in spite of the growth of technological innovations, the increasing complexity of systems involves critical issues in terms of degradation of the safety levels. In such a situation, new safety management approaches are now mandatory in order to face the safety implications of the current technological evolutions. Along these lines, performing risk-based analysis alone seems not to be enough anymore. The evaluation of robustness, antifragility and resilience of a socio-technical system is now indispensable in order to face unforeseen events. This article will briefly introduce the topics of Safety I and Safety II, resilience engineering and antifragility engineering, explaining correlations, overlapping aspects and synergies. Secondly, the article will discuss the applications of those paradigms to a real accident, highlighting how they can challenge, stimulate and inspire research for improving OHS conditions.

  16. Final safety analysis report for the Galileo Mission: Volume 1, Reference design document

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Not Available

    The Galileo mission uses nuclear power sources called Radioisotope Thermoelectric Generators (RTGs) to provide the spacecraft's primary electrical power. Because these generators contain nuclear material, a Safety Analysis Report (SAR) is required. A preliminary SAR and an updated SAR were previously issued that provided an evolving status report on the safety analysis. As a result of the Challenger accident, the launch dates for both Galileo and Ulysses missions were later rescheduled for November 1989 and October 1990, respectively. The decision was made by agreement between the DOE and the NASA to have a revised safety evaluation and report (FSAR) preparedmore » on the basis of these revised vehicle accidents and environments. The results of this latest revised safety evaluation are presented in this document (Galileo FSAR). Volume I, this document, provides the background design information required to understand the analyses presented in Volumes II and III. It contains descriptions of the RTGs, the Galileo spacecraft, the Space Shuttle, the Inertial Upper Stage (IUS), the trajectory and flight characteristics including flight contingency modes, and the launch site. There are two appendices in Volume I which provide detailed material properties for the RTG.« less

  17. Design and application of a tool for structuring, capitalizing and making more accessible information and lessons learned from accidents involving machinery.

    PubMed

    Sadeghi, Samira; Sadeghi, Leyla; Tricot, Nicolas; Mathieu, Luc

    2017-12-01

    Accident reports are published in order to communicate the information and lessons learned from accidents. An efficient accident recording and analysis system is a necessary step towards improvement of safety. However, currently there is a shortage of efficient tools to support such recording and analysis. In this study we introduce a flexible and customizable tool that allows structuring and analysis of this information. This tool has been implemented under TEEXMA®. We named our prototype TEEXMA®SAFETY. This tool provides an information management system to facilitate data collection, organization, query, analysis and reporting of accidents. A predefined information retrieval module provides ready access to data which allows the user to quickly identify the possible hazards for specific machines and provides information on the source of hazards. The main target audience for this tool includes safety personnel, accident reporters and designers. The proposed data model has been developed by analyzing different accident reports.

  18. Anatomy of an Accident.

    ERIC Educational Resources Information Center

    Mobley, Michael

    1984-01-01

    The findings of industrial safety engineers in the areas of accident causation and prevention are wholly applicable to adventure programs. Adventure education instructors can use safety engineering concepts to assess the risk in a particular activity, understand factors that cause accidents, and intervene to minimize injuries and damages if…

  19. Improving Patient Safety in Hospitals: Contributions of High-Reliability Theory and Normal Accident Theory

    PubMed Central

    Tamuz, Michal; Harrison, Michael I

    2006-01-01

    Objective To identify the distinctive contributions of high-reliability theory (HRT) and normal accident theory (NAT) as frameworks for examining five patient safety practices. Data Sources/Study Setting We reviewed and drew examples from studies of organization theory and health services research. Study Design After highlighting key differences between HRT and NAT, we applied the frames to five popular safety practices: double-checking medications, crew resource management (CRM), computerized physician order entry (CPOE), incident reporting, and root cause analysis (RCA). Principal Findings HRT highlights how double checking, which is designed to prevent errors, can undermine mindfulness of risk. NAT emphasizes that social redundancy can diffuse and reduce responsibility for locating mistakes. CRM promotes high reliability organizations by fostering deference to expertise, rather than rank. However, HRT also suggests that effective CRM depends on fundamental changes in organizational culture. NAT directs attention to an underinvestigated feature of CPOE: it tightens the coupling of the medication ordering process, and tight coupling increases the chances of a rapid and hard-to-contain spread of infrequent, but harmful errors. Conclusions Each frame can make a valuable contribution to improving patient safety. By applying the HRT and NAT frames, health care researchers and administrators can identify health care settings in which new and existing patient safety interventions are likely to be effective. Furthermore, they can learn how to improve patient safety, not only from analyzing mishaps, but also by studying the organizational consequences of implementing safety measures. PMID:16898984

  20. Geographic analysis of road accident severity index in Nigeria.

    PubMed

    Iyanda, Ayodeji E

    2018-05-28

    Before 2030, deaths from road traffic accidents (RTAs) will surpass cerebrovascular disease, tuberculosis, and HIV/AIDS. Yet, there is little knowledge on the geographic distribution of RTA severity in Nigeria. Accident Severity Index is the proportion of deaths that result from a road accident. This study analysed the geographic pattern of RTA severity based on the data retrieved from Federal Road Safety Corps (FRSC). The study predicted a two-year data from a historic road accident data using exponential smoothing technique. To determine spatial autocorrelation, global and local indicators of spatial association were implemented in a geographic information system. Results show significant clusters of high RTA severity among states in the northeast and the northwest of Nigeria. Hence, the findings are discussed from two perspectives: Road traffic law compliance and poor emergency response. Conclusion, the severity of RTA is high in the northern states of Nigeria, hence, RTA remains a public health concern.

  1. A comparative analysis of occupational health and safety risk prevention practices in Sweden and Spain.

    PubMed

    Morillas, Rosa María; Rubio-Romero, Juan Carlos; Fuertes, Alba

    2013-12-01

    Scandinavian countries such as Sweden implemented the occupational health and safety (OHS) measures in the European Directive 89/391/EEC earlier than other European counties, including Spain. In fact, statistics on workplace accident rates reveal that between 2004 and 2009, there were considerably fewer accidents in Sweden than in Spain. The objective of the research described in this paper was to reduce workplace accidents and to improve OHS management in Spain by exploring the OHS practices in Sweden. For this purpose, an exploratory comparative study was conducted, which focused on the effectiveness of the EU directive in both countries. The study included a cross-sectional analysis of workplace accident rates and other contextual indicators in both national contexts. A case study of 14 Swedish and Spanish companies identified 14 differences in the preventive practices implemented. These differences were then assessed with a Delphi study to evaluate their contribution to the reduction of workplace accidents and their potential for improving health and safety management in Spain. The results showed that there was agreement concerning 12 of the 14 practices. Finally, we discuss opportunities of improvement in Spanish companies so that they can make their risk management practices more effective. The findings of this comparative study on the implementation of the European Directive 89/391/EEC in both Sweden and Spain have revealed health and safety managerial practices which, if properly implemented, could contribute to improved work conditions and accident statistics of Spanish companies. In particular, the results suggest that Spanish employers, safety managers, external prevention services, safety deputies and Labour Inspectorates should consider implementing streamlined internal preventive management, promoting the integration of prevention responsibilities to the chain of command, and preventing health and safety management from becoming a mere exchange of

  2. A Human Factors Analysis and Classification System (HFACS) Examination of Commercial Vessel Accidents

    DTIC Science & Technology

    2012-09-01

    Naval Operations before the Congress on FY2013 Department of Navy posture. Heinrich , H . W. (1941). Industrial accident prevention : A scientific...Theory The core of the Domino Theory, developed by Herbert W. Heinrich who studied industrial safety in the early 1900s, is that accidents are a result...chain of events resulting in an accident . Heinrich likened the dominos to unsafe conditions or unsafe acts, where their subsequent removal prevents a

  3. Inroads into Equestrian Safety: Rider-Reported Factors Contributing to Horse-Related Accidents and Near Misses on Australian Roads

    PubMed Central

    Thompson, Kirrilly; Matthews, Chelsea

    2015-01-01

    Simple Summary Riding horses on roads can be dangerous, but little is known about accidents and near misses. To explore road safety issues amongst Australian equestrians, we conducted an online survey. More than half of all riders (52%) reported having experienced at least one accident or near miss in the 12 months prior to the survey, mostly attributed to speed. Whilst our findings confirmed factors identified overseas, we also identified issues around road rules, hand signals and road rage. This paper suggests strategies for improving the safety of horses, riders and other road users. Abstract Horse riding and horse-related interactions are inherently dangerous. When they occur on public roads, the risk profile of equestrian activities is complicated by interactions with other road users. Research has identified speed, proximity, visibility, conspicuity and mutual misunderstanding as factors contributing to accidents and near misses. However, little is known about their significance or incidence in Australia. To explore road safety issues amongst Australian equestrians, we conducted an online survey. More than half of all riders (52%) reported having experienced at least one accident or near miss in the 12 months prior to the survey. Whilst our findings confirm the factors identified overseas, we also identified issues around rider misunderstanding of road rules and driver misunderstanding of rider hand signals. Of particular concern, we also found reports of potentially dangerous rider-directed road rage. We identify several areas for potential safety intervention including (1) identifying equestrians as vulnerable road users and horses as sentient decision-making vehicles; (2) harmonising laws regarding passing horses; (3) mandating personal protective equipment; (4) improving road signage; (5) comprehensive data collection; (6) developing mutual understanding amongst road-users; (7) safer road design and alternative riding spaces; and (8) increasing investment

  4. Fatal accidents in nighttime vs. daytime highway construction work zones.

    PubMed

    Arditi, David; Lee, Dong-Eun; Polat, Gul

    2007-01-01

    Awareness about worker safety in nighttime construction has been a major concern because it is believed that nighttime construction creates hazardous work conditions. However, only a few studies provide valuable comparative information about accident characteristics of nighttime and daytime highway construction activities. This study investigates fatal accidents that occurred in Illinois highway work zones in the period 1996-2001 in order to determine the safety differences between nighttime and daytime highway construction. The lighting and weather conditions were included into the study as control parameters to see their effects on the frequency of fatal accidents occurring in work zones. According to this study, there is evidence that nighttime construction is more hazardous than daytime construction. The inclusion of a weather parameter into the analysis has limited effect on this finding. The study justifies establishing an efficient work zone accident reporting system and taking all necessary measures to enhance safety in nighttime work zones.

  5. Human error analysis of commercial aviation accidents: application of the Human Factors Analysis and Classification system (HFACS).

    PubMed

    Wiegmann, D A; Shappell, S A

    2001-11-01

    The Human Factors Analysis and Classification System (HFACS) is a general human error framework originally developed and tested within the U.S. military as a tool for investigating and analyzing the human causes of aviation accidents. Based on Reason's (1990) model of latent and active failures, HFACS addresses human error at all levels of the system, including the condition of aircrew and organizational factors. The purpose of the present study was to assess the utility of the HFACS framework as an error analysis and classification tool outside the military. The HFACS framework was used to analyze human error data associated with aircrew-related commercial aviation accidents that occurred between January 1990 and December 1996 using database records maintained by the NTSB and the FAA. Investigators were able to reliably accommodate all the human causal factors associated with the commercial aviation accidents examined in this study using the HFACS system. In addition, the classification of data using HFACS highlighted several critical safety issues in need of intervention research. These results demonstrate that the HFACS framework can be a viable tool for use within the civil aviation arena. However, additional research is needed to examine its applicability to areas outside the flight deck, such as aircraft maintenance and air traffic control domains.

  6. Comparison of a Traditional Probabilistic Risk Assessment Approach with Advanced Safety Analysis

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Smith, Curtis L; Mandelli, Diego; Zhegang Ma

    2014-11-01

    As part of the Light Water Sustainability Program (LWRS) [1], the purpose of the Risk Informed Safety Margin Characterization (RISMC) [2] Pathway research and development (R&D) is to support plant decisions for risk-informed margin management with the aim to improve economics, reliability, and sustain safety of current NPPs. In this paper, we describe the RISMC analysis process illustrating how mechanistic and probabilistic approaches are combined in order to estimate a safety margin. We use the scenario of a “station blackout” (SBO) wherein offsite power and onsite power is lost, thereby causing a challenge to plant safety systems. We describe themore » RISMC approach, illustrate the station blackout modeling, and contrast this with traditional risk analysis modeling for this type of accident scenario. We also describe our approach we are using to represent advanced flooding analysis.« less

  7. Mine safety assessment using gray relational analysis and bow tie model

    PubMed Central

    2018-01-01

    Mine safety assessment is a precondition for ensuring orderly and safety in production. The main purpose of this study was to prevent mine accidents more effectively by proposing a composite risk analysis model. First, the weights of the assessment indicators were determined by the revised integrated weight method, in which the objective weights were determined by a variation coefficient method and the subjective weights determined by the Delphi method. A new formula was then adopted to calculate the integrated weights based on the subjective and objective weights. Second, after the assessment indicator weights were determined, gray relational analysis was used to evaluate the safety of mine enterprises. Mine enterprise safety was ranked according to the gray relational degree, and weak links of mine safety practices identified based on gray relational analysis. Third, to validate the revised integrated weight method adopted in the process of gray relational analysis, the fuzzy evaluation method was used to the safety assessment of mine enterprises. Fourth, for first time, bow tie model was adopted to identify the causes and consequences of weak links and allow corresponding safety measures to be taken to guarantee the mine’s safe production. A case study of mine safety assessment was presented to demonstrate the effectiveness and rationality of the proposed composite risk analysis model, which can be applied to other related industries for safety evaluation. PMID:29561875

  8. Lifestyle and accidents among young drivers.

    PubMed

    Gregersen, N P; Berg, H Y

    1994-06-01

    This study covers the lifestyle component of the problems related to young drivers' accident risk. The purpose of the study is to measure the relationship between lifestyle and accident risk, and to identify specific high-risk and low-risk groups. Lifestyle is measured through a questionnaire, where 20-year-olds describe themselves and how often they deal with a large number of different activities, like sports, music, movies, reading, cars and driving, political engagement, etc. They also report their involvement in traffic accidents. With a principal component analysis followed by a cluster analysis, lifestyle profiles are defined. These profiles are finally correlated to accidents, which makes it possible to define high-risk and low-risk groups. The cluster analysis defined 15 clusters including four high-risk groups with an average overrisk of 150% and two low-risk groups with an average underrisk of 75%. The results are discussed from two perspectives. The first is the importance of theoretical understanding of the contribution of lifestyle factors to young drivers' high accident risk. The second is how the findings could be used in practical road safety measures, like education, campaigns, etc.

  9. Off-road truck-related accidents in U.S. mines

    PubMed Central

    Dindarloo, Saeid R.; Pollard, Jonisha P.; Siami-Irdemoosa, Elnaz

    2016-01-01

    Introduction Off-road trucks are one of the major sources of equipment-related accidents in the U.S. mining industries. A systematic analysis of all off-road truck-related accidents, injuries, and illnesses, which are reported and published by the Mine Safety and Health Administration (MSHA), is expected to provide practical insights for identifying the accident patterns and trends in the available raw database. Therefore, appropriate safety management measures can be administered and implemented based on these accident patterns/trends. Methods A hybrid clustering-classification methodology using K-means clustering and gene expression programming (GEP) is proposed for the analysis of severe and non-severe off-road truck-related injuries at U.S. mines. Using the GEP sub-model, a small subset of the 36 recorded attributes was found to be correlated to the severity level. Results Given the set of specified attributes, the clustering sub-model was able to cluster the accident records into 5 distinct groups. For instance, the first cluster contained accidents related to minerals processing mills and coal preparation plants (91%). More than two-thirds of the victims in this cluster had less than 5 years of job experience. This cluster was associated with the highest percentage of severe injuries (22 severe accidents, 3.4%). Almost 50% of all accidents in this cluster occurred at stone operations. Similarly, the other four clusters were characterized to highlight important patterns that can be used to determine areas of focus for safety initiatives. Conclusions The identified clusters of accidents may play a vital role in the prevention of severe injuries in mining. Further research into the cluster attributes and identified patterns will be necessary to determine how these factors can be mitigated to reduce the risk of severe injuries. Practical application Analyzing injury data using data mining techniques provides some insight into attributes that are associated with

  10. A profile of fatal accidents involving alcohol

    DOT National Transportation Integrated Search

    1977-09-01

    Author's abstract: Accident investigation studies were conducted during 1971-75 in the cities of Boston, Baltimore, Oklahoma City and Albuquerque where Alcohol Safety Action Programs (ASAPs) were operating. Analysis of the four studies, plus newly av...

  11. Analysis of Incident and Accident Reports and Risk Management in Spine Surgery.

    PubMed

    Kobayashi, Kazuyoshi; Imagama, Shiro; Ando, Kei; Hida, Tetsuro; Ito, Kenyu; Tsushima, Mikito; Ishikawa, Yoshimoto; Matsumoto, Akiyuki; Morozumi, Masayoshi; Nishida, Yoshihiro; Nagao, Yoshimasa; Ishiguro, Naoki

    2017-08-01

    A review of accident and incident reports. To analyze prevalence, characteristics, and details of perioperative incidents and accidents in patients receiving spine surgery. In our institution, a clinical error that potentially results in an adverse event is usually submitted as an incident or accident report through a web database, to ensure anonymous and blame-free reporting. All reports are analyzed by a medical safety management group. These reports contain valuable data for management of medical safety, but there have been no studies evaluating such data for spine surgery. A total of 320 incidents and accidents that occurred perioperatively in 172 of 415 spine surgeries were included in the study. Incidents were defined as events that were "problematic, but with no damage to the patient," and accidents as events "with damage to the patient." The details of these events were analyzed. There were 278 incidents in 137 surgeries and 42 accidents in 35 surgeries, giving prevalence of 33% (137/415) and 8% (35/415), respectively. The proportion of accidents among all events was significantly higher for doctors than non-doctors [68.0% (17/25) vs. 8.5% (25/295), P < 0.01] and in the operating room compared with outside the operating room [40.5% (15/37) vs. 9.5% (27/283), P < 0.01]. There was no significant difference in years of experience among personnel involved in all events. The major types of events were medication-related, line and tube problems, and falls and slips. Accidents also occurred because of a long-term prone position, with complications such as laryngeal edema, ulnar nerve palsy, and tooth damage. Surgery and procedures in the operating room always have a risk of complications. Therefore, a particular effort is needed to establish safe management of this environment and to provide advice on risk to the doctor and medical care team. 4.

  12. Safety of High Speed and Guided Ground Transportation Systems: Collision Avoidance and Accident Survivability: Volume 3

    DOT National Transportation Integrated Search

    1993-03-01

    This report is the third of four volumes concerned with developing safety guidelines and specifications for high-speed : guided ground transportation (HSGGT) collision avoidance and accident survivability. The overall approach taken in : this study i...

  13. Frequency of Specific Categories of Aviation Accidents and Incidents During 2001-2010

    NASA Technical Reports Server (NTRS)

    Evans, Joni K.

    2014-01-01

    The purpose of this study was to determine the types of accidents or incidents that are most important to the aviation safety risk. All accidents and incidents from 2001-2010 were assigned occurrence categories based on the taxonomy developed by the Commercial Aviation Safety Team/International Civil Aviation Organization (CAST/ICAO) Common Taxonomy Team (CICTT). The most frequently recorded categories were selected within each of five metrics: total accidents, fatal accidents, total injuries, fatal injuries and total incidents. This analysis was done separately for events within Part 121, Scheduled Part 135, Non-Scheduled Part 135 and Part 91. Combining those five sets of categories resulted in groups of between seven and eleven occurrence categories, depending on the flight operation. These groups represent 65-85% of all accidents and 68-81% of incidents.

  14. Factor Analysis of Traffic Safety in Urban Roads Based on FTA-LEC

    NASA Astrophysics Data System (ADS)

    Shuicheng, TIAN; Xingbo, YANG; Xiaoqing, SHEN; Detao, ZHANG

    2018-05-01

    In order to reduce the number and the loss of urban road traffic accidents in our country, improve the safety of road traffic, a statistical analysis of the research report on major road traffic accidents in 2016 was conducted. The risk factors affecting urban road traffic in China were analyzed by using FTA to find the basic hidden events. Secondly, the risk value of the identified hidden danger events were calculated and classified into four levels I, II, III and IV through the LEC evaluation method. Finally, the graded results of risk factors are verified through a case of specific accidents in Beijing. The results show that: the case verified the scientificalness and effectiveness of hazard classification and provided guidance for urban road traffic management.

  15. Safety of high-speed guided ground transportation : collision avoidance and accident survivability : volume 1 : collision threat

    DOT National Transportation Integrated Search

    1993-03-01

    This report is the first of four volumes concerned with developing safety guidelines and specifications for high-speed guided ground transportation (HSGGT) collision avoidance and accident survivability. The overall approach taken in this study is to...

  16. The Evaluation of the Safety Benefits of Combined Passive and On-Board Active Safety Applications

    PubMed Central

    Page, Yves; Cuny, Sophie; Zangmeister, Tobias; Kreiss, Jens-Peter; Hermitte, Thierry

    2009-01-01

    One of the objectives of the European TRACE project (TRaffic Accident Causation in Europe, 2006–2008) was to estimate the proportion of injury accidents that could be avoided and/or the proportion of injury accidents where the severity could be mitigated for on-the-market safety applications, if 100 % of the car fleet would be equipped with them. We have selected for evaluation the Electronic Stability Control (ESC) and the Emergency Brake Assist (EBA) applications. As for passive safety systems, recent cars are designed to offer overall safety protection. Car structure, load limiters, front airbags, side airbags, knee airbags, pretensioners, padding and non aggressive structures in the door panel, the dashboard, the windshield, the seats, and the head rest also contribute to applying more protection. The whole safety package is very difficult to evaluate separately, one element independently segmented from the others. We decided to consider evaluating the effectivenessof the whole passive safety package, This package,, for the sake of simplicity, was the number of stars awarded at the Euro NCAP testing. The challenges were to compare the effectiveness of some safety configuration SC I, with the effectiveness of a different safety configuration SC II. A safety configuration is understood as a package of safety functions. Ten comparisons have been carried out such as the evaluation of the safety benefit of a fifth star given that the car has four stars and an EBA. The main outcome of this analysis is that any addition of a passive or active safety function selected in this analysis is producing increased safety benefits. For example, if all cars were five stars fitted with EBA and ESC, instead of four stars without ESC and EBA, injury accidents would be reduced by 47.2% for severe injuries and 69.5% for fatal injuries. PMID:20184838

  17. Explaining the road accident risk: weather effects.

    PubMed

    Bergel-Hayat, Ruth; Debbarh, Mohammed; Antoniou, Constantinos; Yannis, George

    2013-11-01

    This research aims to highlight the link between weather conditions and road accident risk at an aggregate level and on a monthly basis, in order to improve road safety monitoring at a national level. It is based on some case studies carried out in Work Package 7 on "Data analysis and synthesis" of the EU-FP6 project "SafetyNet-Building the European Road Safety Observatory", which illustrate the use of weather variables for analysing changes in the number of road injury accidents. Time series analysis models with explanatory variables that measure the weather quantitatively were used and applied to aggregate datasets of injury accidents for France, the Netherlands and the Athens region, over periods of more than 20 years. The main results reveal significant correlations on a monthly basis between weather variables and the aggregate number of injury accidents, but the magnitude and even the sign of these correlations vary according to the type of road (motorways, rural roads or urban roads). Moreover, in the case of the interurban network in France, it appears that the rainfall effect is mainly direct on motorways--exposure being unchanged, and partly indirect on main roads--as a result of changes in exposure. Additional results obtained on a daily basis for the Athens region indicate that capturing the within-the-month variability of the weather variables and including it in a monthly model highlights the effects of extreme weather. Such findings are consistent with previous results obtained for France using a similar approach, with the exception of the negative correlation between precipitation and the number of injury accidents found for the Athens region, which is further investigated. The outlook for the approach and its added value are discussed in the conclusion. Copyright © 2013. Published by Elsevier Ltd.

  18. Accident investigation

    NASA Technical Reports Server (NTRS)

    Laynor, William G. Bud

    1987-01-01

    The National Transportation Safety Board (NTSB) has attributed wind shear as a cause or contributing factor in 15 accidents involving transport-categroy airplanes since 1970. Nine of these were nonfatal; but the other six accounted for 440 lives. Five of the fatal accidents and seven of the nonfatal accidents involved encounters with convective downbursts or microbursts. Of other accidents, two which were nonfatal were encounters with a frontal system shear, and one which was fatal was the result of a terrain induced wind shear. These accidents are discussed with reference to helping the aircraft to avoid the wind shear or if impossible to help the pilot to get through the wind shear.

  19. The role of parental risk judgements, transport safety attitudes, transport priorities and accident experiences on pupils' walking to school.

    PubMed

    Mehdizadeh, Milad; Nordfjaern, Trond; Mamdoohi, Amir Reza; Shariat Mohaymany, Afshin

    2017-05-01

    Walking to school could improve pupils' health condition and might also reduce the use of motorized transport modes, which leads to both traffic congestion and air pollution. The current study aims to examine the role of parental risk judgements (i.e. risk perception and worry), transport safety attitudes, transport priorities and accident experiences on pupils' walking and mode choices on school trips in Iran, a country with poor road safety records. A total of 1078 questionnaires were randomly distributed among pupils at nine public and private schools in January 2014 in Rasht, Iran. Results from valid observations (n=711) showed that parents with high probability assessments of accidents and strong worry regarding pupils' accident risk while walking were less likely to let their children walk to school. Parents with high safety knowledge were also more likely to allow their pupils to walk to school. Parents who prioritized convenience and accessibility in transport had a stronger tendency to choose motorized modes over walking modes. Also, parents who prioritized safety and security in transport were less likely to allow pupils to walk to school. Elasticities results showed that a one percent increase in priorities of convenience and accessibility, priorities of safety and security, car ownership and walking time from home to school reduced walking among pupils by a probability of 0.62, 0.20, 0.86 and 0.57%, respectively. A one percent increase in parental safety knowledge increased the walking probability by around 0.25%. A 1 unit increase in parental probability assessment and worry towards pupils' walking, decreased the probability of choosing walking mode by 0.11 and 0.05, respectively. Policy-makers who aim to promote walking to schools should improve safety and security of the walking facilities and increase parental safety knowledge. Copyright © 2017 Elsevier Ltd. All rights reserved.

  20. Characteristics of worker accidents on NYSDOT construction projects.

    PubMed

    Mohan, Satish; Zech, Wesley C

    2005-01-01

    This paper aims at providing cost-effective safety measures to protect construction workers in highway work zones, based on real data. Two types of accidents that occur in work zones were: (a) construction work area accidents, and (b) traffic accidents involving construction worker(s). A detailed analysis of work zone accidents involving 36 fatalities and 3,055 severe injuries to construction workers on New York State Department of Transportation (NYSDOT) construction projects from 1990 to 2001 established that five accident types: (a) Struck/Pinned by Large Equipment, (b) Trip or Fall (elevated), (c) Contact w/Electrical or Gas Utility, (d) Struck-by Moving/Falling Load, and (e) Crane/Lift Device Failure accounted for nearly 96% of the fatal accidents, nearly 63% of the hospital-level injury accidents, and nearly 91% of the total costs. These construction work area accidents had a total cost of $133.8 million. Traffic accidents that involve contractors' employees were also examined. Statistical analyses of the traffic accidents established that five traffic accident types: (a) Work Space Intrusion, (b) Worker Struck-by Vehicle Inside Work Space, (c) Flagger Struck-by Vehicle, (d) Worker Struck-by Vehicle Entering/Exiting Work Space, and (e) Construction Equipment Struck-by Vehicle Inside Work Space accounted for nearly 86% of the fatal, nearly 70% of the hospital-level injury and minor injury traffic accidents, and $45.4 million (79.4%) of the total traffic accident costs. The results of this paper provide real statistics on construction worker related accidents reported on construction work zones. Potential preventions based on real statistics have also been suggested. The ranking of accident types, both within the work area as well as in traffic, will guide the heavy highway contractor and owner agencies in identifying the most cost effective safety preventions.

  1. Linguistic analysis of large-scale medical incident reports for patient safety.

    PubMed

    Fujita, Katsuhide; Akiyama, Masanori; Park, Keunsik; Yamaguchi, Etsuko Nakagami; Furukawa, Hiroyuki

    2012-01-01

    The analysis of medical incident reports is indispensable for patient safety. The cycles between analysis of incident reports and proposals to medical staffs are a key point for improving the patient safety in the hospital. Most incident reports are composed from freely written descriptions, but an analysis of such free descriptions is not sufficient in the medical field. In this study, we aim to accumulate and reinterpret findings using structured incident information, to clarify improvements that should be made to solve the root cause of the accident, and to ensure safe medical treatment through such improvements. We employ natural language processing (NLP) and network analysis to identify effective categories of medical incident reports. Network analysis can find various relationships that are not only direct but also indirect. In addition, we compare bottom-up results obtained by NLP with existing categories based on experts' judgment. By the bottom-up analysis, the class of patient managements regarding patients' fallings and medicines in top-down analysis is created clearly. Finally, we present new perspectives on ways of improving patient safety.

  2. Epidemiology of Accidents in Tile Factories of Mangalore City in Karnataka

    PubMed Central

    Kumar, S Ganesh; Rathnakar, UP; Harsha Kumar, HN

    2010-01-01

    Background: Occupational accidents are a major point of concern in industries. The academic community should take the first step to address the long-neglected concerns of occupational safety. Objective: To assess the prevalence and pattern of occupational accidents. Materials and Methods: A record-based, cross-sectional study was done in three tile factories of Mangalore city, in Karnataka. A total of 416 workers were analyzed for the year 2004, and data regarding age, sex, job duration, type and nature of injury, body parts involved, and time of injury were collected in a prestructured proforma. Statistical Analysis: Proportions, Chi-square test, Univariate and Multivariate analysis. Results: The overall prevalence rate of accidents was found to be 18.5%. It was found that almost around 86% of the accidents had affected the limbs (upper limb 24.7%, lower limb 61%), around half (52%) of the injuries were contributed by superficial injuries, 40% of accidents were due to stepping/striking against objects and while handling. Hand tools and machinery in motion contributed to around 20% of the accidents. Accidents were more common among the younger age group and less-experienced workers. Multiple logistic regression analyses revealed that the age group of 30-39 years had an independent significant association with accidents (OR = 0.21, P = 0.04). Conclusion: Accidents in tile industries are an important occupational health problem in this area of the country. There is a need for proper safety training of the workers. PMID:20606926

  3. Systematic strategies for the third industrial accident prevention plan in Korea.

    PubMed

    Kang, Young-sig; Yang, Sung-hwan; Kim, Tae-gu; Kim, Day-sung

    2012-01-01

    To minimize industrial accidents, it's critical to evaluate a firm's priorities for prevention factors and strategies since such evaluation provides decisive information for preventing industrial accidents and maintaining safety management. Therefore, this paper proposes the evaluation of priorities through statistical testing of prevention factors with a cause analysis in a cause and effect model. A priority matrix criterion is proposed to apply the ranking and for the objectivity of questionnaire results. This paper used regression method (RA), exponential smoothing method (ESM), double exponential smoothing method (DESM), autoregressive integrated moving average (ARIMA) model and proposed analytical function method (PAFM) to analyze trends of accident data that will lead to an accurate prediction. This paper standardized the questionnaire results of workers and managers in manufacturing and construction companies with less than 300 employees, located in the central Korean metropolitan areas where fatal accidents have occurred. Finally, a strategy was provided to construct safety management for the third industrial accident prevention plan and a forecasting method for occupational accident rates and fatality rates for occupational accidents per 10,000 people.

  4. Risk-based Analysis of Construction Accidents in Iran During 2007-2011-Meta Analyze Study

    PubMed Central

    AMIRI, Mehran; ARDESHIR, Abdollah; FAZEL ZARANDI, Mohammad Hossein

    2014-01-01

    Abstract Background The present study aimed to investigate the characteristics of occupational accidents and frequency and severity of work related accidents in the construction industry among Iranian insured workers during the years 20072011. Methods The Iranian Social Security Organization (ISSO) accident database containing 21,864 cases between the years 2007-2011 was applied in this study. In the next step, Total Accident Rate (TRA), Total Severity Index (TSI), and Risk Factor (RF) were defined. The core of this work is devoted to analyzing the data from different perspectives such as age of workers, occupation and construction phase, day of the week, time of the day, seasonal analysis, regional considerations, type of accident, and body parts affected. Results Workers between 15-19 years old (TAR=13.4%) are almost six times more exposed to risk of accident than the average of all ages (TAR=2.51%). Laborers and structural workers (TAR=66.6%) and those working at heights (TAR=47.2%) experience more accidents than other groups of workers. Moreover, older workers over 65 years old (TSI=1.97%> average TSI=1.60%), work supervisors (TSI=12.20% >average TSI=9.09%), and night shift workers (TSI=1.89% >average TSI=1.47%) are more prone to severe accidents. Conclusion It is recommended that laborers, young workers, weekend and night shift workers be supervised more carefully in the workplace. Use of Personal Protective Equipment (PPE) should be compulsory in working environments, and special attention should be undertaken to people working outdoors and at heights. It is also suggested that policymakers pay more attention to the improvement of safety conditions in deprived and cold western regions. PMID:26005662

  5. Risk-based Analysis of Construction Accidents in Iran During 2007-2011-Meta Analyze Study.

    PubMed

    Amiri, Mehran; Ardeshir, Abdollah; Fazel Zarandi, Mohammad Hossein

    2014-04-01

    The present study aimed to investigate the characteristics of occupational accidents and frequency and severity of work related accidents in the construction industry among Iranian insured workers during the years 20072011. The Iranian Social Security Organization (ISSO) accident database containing 21,864 cases between the years 2007-2011 was applied in this study. In the next step, Total Accident Rate (TRA), Total Severity Index (TSI), and Risk Factor (RF) were defined. The core of this work is devoted to analyzing the data from different perspectives such as age of workers, occupation and construction phase, day of the week, time of the day, seasonal analysis, regional considerations, type of accident, and body parts affected. Workers between 15-19 years old (TAR=13.4%) are almost six times more exposed to risk of accident than the average of all ages (TAR=2.51%). Laborers and structural workers (TAR=66.6%) and those working at heights (TAR=47.2%) experience more accidents than other groups of workers. Moreover, older workers over 65 years old (TSI=1.97%> average TSI=1.60%), work supervisors (TSI=12.20% >average TSI=9.09%), and night shift workers (TSI=1.89% >average TSI=1.47%) are more prone to severe accidents. It is recommended that laborers, young workers, weekend and night shift workers be supervised more carefully in the workplace. Use of Personal Protective Equipment (PPE) should be compulsory in working environments, and special attention should be undertaken to people working outdoors and at heights. It is also suggested that policymakers pay more attention to the improvement of safety conditions in deprived and cold western regions.

  6. Gyroplane accidents 1985-2005: epidemiological analysis and pilot factors in 223 events.

    PubMed

    Pagán, Brian J; de Voogt, Alex

    2008-10-01

    Gyroplanes (autogyros) are regarded as a relatively safe and stable type of general-aviation aircraft. The U.S. Federal Aviation Administration categorizes them as sport pilot/light sport aircraft, and reports of gyroplane accidents are included in a publicly available database. We hypothesized that issues related to pilot experience and aircraft maintenance would affect the severity of accidents as indicated by aircraft damage and fatalities. A search of the National Transportation Safety Board database for the period 1985-2005 yielded 223 reports of gyroplane accidents. Information from those reports was compiled and cross-referenced with pilot performance breakdowns and contextual information. The data was then analyzed using the Human Factors Analysis and Classification System. There was a strong effect of pilot experience on crash outcomes; compared to more experienced pilots, crashes involving pilots with less than 40 flight hours in the same make/model gyroplane were five times more likely to involve loss of control, twice as likely to destroy the aircraft, and four times more likely to involve fatalities. On the other hand, crashes involving pilots with more than 40 make/model hours were more likely to be related to perception-based performance breakdown. Maintenance issues were not found to play a significant role in this sample of crashes. The results support the hypothesis that pilot experience is a significant predictor of accident fatality in gyroplanes. Training that is adapted to the experience level of pilots as implemented in new FAA regulations for sport pilot and light sport aircraft (2004) may help to reduce the frequency and seriousness of gyroplane accidents.

  7. Data Analysis Approaches for the Risk-Informed Safety Margins Characterization Toolkit

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Mandelli, Diego; Alfonsi, Andrea; Maljovec, Daniel P.

    2016-09-01

    In the past decades, several numerical simulation codes have been employed to simulate accident dynamics (e.g., RELAP5-3D, RELAP-7, MELCOR, MAAP). In order to evaluate the impact of uncertainties into accident dynamics, several stochastic methodologies have been coupled with these codes. These stochastic methods range from classical Monte-Carlo and Latin Hypercube sampling to stochastic polynomial methods. Similar approaches have been introduced into the risk and safety community where stochastic methods (such as RAVEN, ADAPT, MCDET, ADS) have been coupled with safety analysis codes in order to evaluate the safety impact of timing and sequencing of events. These approaches are usually calledmore » Dynamic PRA or simulation-based PRA methods. These uncertainties and safety methods usually generate a large number of simulation runs (database storage may be on the order of gigabytes or higher). The scope of this paper is to present a broad overview of methods and algorithms that can be used to analyze and extract information from large data sets containing time dependent data. In this context, “extracting information” means constructing input-output correlations, finding commonalities, and identifying outliers. Some of the algorithms presented here have been developed or are under development within the RAVEN statistical framework.« less

  8. Prospective Safety Analysis and the Complex Aviation System

    NASA Technical Reports Server (NTRS)

    Smith, Brian E.

    2013-01-01

    Fatal accident rates in commercial passenger aviation are at historic lows yet have plateaued and are not showing evidence of further safety advances. Modern aircraft accidents reflect both historic causal factors and new unexpected "Black Swan" events. The ever-increasing complexity of the aviation system, along with its associated technology and organizational relationships, provides fertile ground for fresh problems. It is important to take a proactive approach to aviation safety by working to identify novel causation mechanisms for future aviation accidents before they happen. Progress has been made in using of historic data to identify the telltale signals preceding aviation accidents and incidents, using the large repositories of discrete and continuous data on aircraft and air traffic control performance and information reported by front-line personnel. Nevertheless, the aviation community is increasingly embracing predictive approaches to aviation safety. The "prospective workshop" early assessment tool described in this paper represents an approach toward this prospective mindset-one that attempts to identify the future vectors of aviation and asks the question: "What haven't we considered in our current safety assessments?" New causation mechanisms threatening aviation safety will arise in the future because new (or revised) systems and procedures will have to be used under future contextual conditions that have not been properly anticipated. Many simulation models exist for demonstrating the safety cases of new operational concepts and technologies. However the results from such models can only be as valid as the accuracy and completeness of assumptions made about the future context in which the new operational concepts and/or technologies will be immersed. Of course that future has not happened yet. What is needed is a reasonably high-confidence description of the future operational context, capturing critical contextual characteristics that modulate

  9. Cross-comparison of three surrogate safety methods to diagnose cyclist safety problems at intersections in Norway.

    PubMed

    Laureshyn, Aliaksei; Goede, Maartje de; Saunier, Nicolas; Fyhri, Aslak

    2017-08-01

    Relying on accident records as the main data source for studying cyclists' safety has many drawbacks, such as high degree of under-reporting, the lack of accident details and particularly of information about the interaction processes that led to the accident. It is also an ethical problem as one has to wait for accidents to happen in order to make a statement about cyclists' (un-)safety. In this perspective, the use of surrogate safety measures based on actual observations in traffic is very promising. In this study we used video data from three intersections in Norway that were all independently analysed using three methods: the Swedish traffic conflict technique (Swedish TCT), the Dutch conflict technique (DOCTOR) and the probabilistic surrogate measures of safety (PSMS) technique developed in Canada. The first two methods are based on manual detection and counting of critical events in traffic (traffic conflicts), while the third considers probabilities of multiple trajectories for each interaction and delivers a density map of potential collision points per site. Due to extensive use of microscopic data, PSMS technique relies heavily on automated tracking of the road users in video. Across the three sites, the methods show similarities or are at least "compatible" with the accident records. The two conflict techniques agree quite well for the number, type and location of conflicts, but some differences with no obvious explanation are also found. PSMS reports many more safety-relevant interactions including less severe events. The location of the potential collision points is compatible with what the conflict techniques suggest, but the possibly significant share of false alarms due to inaccurate trajectories extracted from video complicates the comparison. The tested techniques still require enhancement, with respect to better adjustment to analysis of the situations involving cyclists (and vulnerable road users in general) and further validation. However, we

  10. Industrial Safety and Utopia: Insights from the Fukushima Daiichi Accident.

    PubMed

    Travadel, Sébastien; Guarnieri, Franck; Portelli, Aurélien

    2018-01-01

    Feedback from industrial accidents is provided by various state or even international, institutions, and lessons learned can be controversial. However, there has been little research into organizational learning at the international level. This article helps to fill the gap through an in-depth review of official reports of the Fukushima Daiichi accident published shortly after the event. We present a new method to analyze the arguments contained in these voluminous documents. Taking an intertextual perspective, the method focuses on the accident narratives, their rationale, and links between "facts," "causes," and "recommendations." The aim is to evaluate how the findings of the various reports are consistent with (or contradict) "institutionalized knowledge," and identify the social representations that underpin them. We find that although the scientific controversy surrounding the results of the various inquiries reflects different ethical perspectives, they are integrated into the same utopian ideal. The involvement of multiple actors in this controversy raises questions about the public construction of epistemic authority, and we highlight the special status given to the International Atomic Energy Agency in this regard. © 2017 The Authors Risk Analysis published by Wiley Periodicals, Inc. on behalf of Society for Risk Analysis.

  11. Safety of High Speed Guided Ground Transportation Systems: Collision Avoidance and Accident Survivability Volume 4: Proposed Specifications

    DOT National Transportation Integrated Search

    1993-03-01

    This report is the fourth of four volumes concerned with developing safety guidelines and specifications for high-speed : guided ground transportation (HSGGT) collision avoidance and accident survivability. The overall approach taken in this : study ...

  12. 49 CFR 195.54 - Accident reports.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Accident reports. 195.54 Section 195.54 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY TRANSPORTATION OF HAZARDOUS LIQUIDS BY PIPELINE Annual, Accident, and...

  13. The predictive validity of safety climate.

    PubMed

    Johnson, Stephen E

    2007-01-01

    Safety professionals have increasingly turned their attention to social science for insight into the causation of industrial accidents. One social construct, safety climate, has been examined by several researchers [Cooper, M. D., & Phillips, R. A. (2004). Exploratory analysis of the safety climate and safety behavior relationship. Journal of Safety Research, 35(5), 497-512; Gillen, M., Baltz, D., Gassel, M., Kirsch, L., & Vacarro, D. (2002). Perceived safety climate, job Demands, and coworker support among union and nonunion injured construction workers. Journal of Safety Research, 33(1), 33-51; Neal, A., & Griffin, M. A. (2002). Safety climate and safety behaviour. Australian Journal of Management, 27, 66-76; Zohar, D. (2000). A group-level model of safety climate: Testing the effect of group climate on microaccidents in manufacturing jobs. Journal of Applied Psychology, 85(4), 587-596; Zohar, D., & Luria, G. (2005). A multilevel model of safety climate: Cross-level relationships between organization and group-level climates. Journal of Applied Psychology, 90(4), 616-628] who have documented its importance as a factor explaining the variation of safety-related outcomes (e.g., behavior, accidents). Researchers have developed instruments for measuring safety climate and have established some degree of psychometric reliability and validity. The problem, however, is that predictive validity has not been firmly established, which reduces the credibility of safety climate as a meaningful social construct. The research described in this article addresses this problem and provides additional support for safety climate as a viable construct and as a predictive indicator of safety-related outcomes. This study used 292 employees at three locations of a heavy manufacturing organization to complete the 16 item Zohar Safety Climate Questionnaire (ZSCQ) [Zohar, D., & Luria, G. (2005). A multilevel model of safety climate: Cross-level relationships between organization and group

  14. The effect of challenge and hindrance stressors on safety behavior and safety outcomes: a meta-analysis.

    PubMed

    Clarke, Sharon

    2012-10-01

    The significance of occupational stressors as a risk factor in accidents has long been recognized; however, the behavioral mechanisms underlying this relationship are currently not well-understood. Meta-analysis was utilized to test the relationships between occupational stressors (challenge and hindrance), safety behaviors (compliance and participation), and safety outcomes (occupational injuries and near-misses). It was hypothesized that hindrance stressors would have negative effects on both safety compliance and safety participation, and subsequently, safety outcomes, whereas challenge stressors would have positive effects. The hypotheses relating to hindrance stressors were supported, suggesting that hindrance stressors lead to a significant reduction in both compliance with safety rules and participation in safety-related activities. Hindrance stressors were also associated with higher levels of occupational injuries and near-misses. The relationship between hindrance stressors and occupational injuries was fully mediated by safety behaviors. However, the hypotheses related to challenge stressors were not supported. Challenge stressors had a nonsignificant, near-zero association with compliance and occupational injuries, a small negative association with participation, and a small positive association with near-misses. The theoretical and practical implications of the meta-analytic findings are discussed, as well as avenues for further research.

  15. Analysis of the FeCrAl Accident Tolerant Fuel Concept Benefits during BWR Station Blackout Accidents

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Robb, Kevin R

    2015-01-01

    Iron-chromium-aluminum (FeCrAl) alloys are being considered for fuel concepts with enhanced accident tolerance. FeCrAl alloys have very slow oxidation kinetics and good strength at high temperatures. FeCrAl could be used for fuel cladding in light water reactors and/or as channel box material in boiling water reactors (BWRs). To estimate the potential safety gains afforded by the FeCrAl concept, the MELCOR code was used to analyze a range of postulated station blackout severe accident scenarios in a BWR/4 reactor employing FeCrAl. The simulations utilize the most recently known thermophysical properties and oxidation kinetics for FeCrAl. Overall, when compared to the traditionalmore » Zircaloy-based cladding and channel box, the FeCrAl concept provides a few extra hours of time for operators to take mitigating actions and/or for evacuations to take place. A coolable core geometry is retained longer, enhancing the ability to stabilize an accident. Finally, due to the slower oxidation kinetics, substantially less hydrogen is generated, and the generation is delayed in time. This decreases the amount of non-condensable gases in containment and the potential for deflagrations to inhibit the accident response.« less

  16. Safety of high-speed guided ground transportation systems : collision avoidance and accident survivability : volume 4 : proposed specifications

    DOT National Transportation Integrated Search

    1993-03-01

    This report is the fourth of four volumes concerned with developing safety guidelines and specifications for high-speed guided ground transportation (HSGGT) collision avoidance and accident survivability. The overall approach taken in this study is t...

  17. Safety of high-speed guided ground transportation systems : collision avoidance and accident survivability : volume 2 : collision avoidance

    DOT National Transportation Integrated Search

    1993-03-01

    This report is the second of four volumes concerned with developing safety guidelines and specifications for high-speed guided ground transportation (HSGGT) collision avoidance and accident survivability. The overall approach taken in this study is t...

  18. Tools for improving safety management in the Norwegian Fishing Fleet occupational accidents analysis period of 1998-2006.

    PubMed

    Aasjord, Halvard L

    2006-01-01

    Reporting of human accidents in the Norwegian Fishing Fleet has always been very difficult because there has been no tradition in making reports on all types of working accidents among fishermen, if the accident does not seem to be very serious or there is no economical incentive to report. Therefore reports are only written when the accidents are serious or if the fisherman is reported sick. Reports about an accident are sent to the insurance company, but another report should also be sent to the Norwegian Maritime Directorate (NMD). Comparing of data from one former insurance company and NMD shows that the real numbers of injuries or serious accidents among Norwegian fishermen could be up to two times more than the numbers reported to NMD. Special analyses of 1690 accidents from the so called PUS-database (NMD) for the period 1998-2002, show that the calculated risk was 23.6 accidents per 1000 man-years. This is quite a high risk level, and most of the accidents in the fishing fleet were rather serious. The calculated risks are highest for fishermen on board the deep sea fleet of trawlers (28.6 accidents per 1000 man-years) and also on the deep sea fleet of purse seiners (28.9 accidents per 1000 man-years). Fatal accidents over a longer period of 51.5 years from 1955 to 2006 are also roughly analysed. These data from SINTEF's own database show that the numbers of fatal accidents have been decreasing over this long period, except for the two periods 1980-84 and 1990-94 where we had some casualties with total losses of larger vessels with the loss of most of the crew, but also many others typical work accidents on smaller vessels. The total numbers of registered Norwegian fishermen and also the numbers of man-years have been drastically reduced over the 51.5 years from 1955 to 2006. The risks of fatal accidents have been very steady over time at a high level, although there has been a marked risk reduction since 1990-94. For the last 8.5-year period of January 1998

  19. 49 CFR 835.11 - Obtaining Board accident reports, factual accident reports, and supporting information.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 7 2012-10-01 2012-10-01 false Obtaining Board accident reports, factual accident reports, and supporting information. 835.11 Section 835.11 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL TRANSPORTATION SAFETY BOARD TESTIMONY OF BOARD EMPLOYEES § 835.11 Obtaining Board accident reports, factual...

  20. 49 CFR 835.11 - Obtaining Board accident reports, factual accident reports, and supporting information.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 7 2011-10-01 2011-10-01 false Obtaining Board accident reports, factual accident reports, and supporting information. 835.11 Section 835.11 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL TRANSPORTATION SAFETY BOARD TESTIMONY OF BOARD EMPLOYEES § 835.11 Obtaining Board accident reports, factual...

  1. 49 CFR 835.11 - Obtaining Board accident reports, factual accident reports, and supporting information.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 7 2014-10-01 2014-10-01 false Obtaining Board accident reports, factual accident reports, and supporting information. 835.11 Section 835.11 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL TRANSPORTATION SAFETY BOARD TESTIMONY OF BOARD EMPLOYEES § 835.11 Obtaining Board accident reports, factual...

  2. 49 CFR 835.11 - Obtaining Board accident reports, factual accident reports, and supporting information.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 7 2013-10-01 2013-10-01 false Obtaining Board accident reports, factual accident reports, and supporting information. 835.11 Section 835.11 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL TRANSPORTATION SAFETY BOARD TESTIMONY OF BOARD EMPLOYEES § 835.11 Obtaining Board accident reports, factual...

  3. Geotechnical approach for occupational safety risk analysis of critical slope in open pit mining as implication for earthquake hazard

    NASA Astrophysics Data System (ADS)

    Munirwansyah; Irsyam, Masyhur; Munirwan, Reza P.; Yunita, Halida; Zulfan Usrina, M.

    2018-05-01

    Occupational safety and health (OSH) is a planned effort to prevent accidents and diseases caused by work. In conducting mining activities often occur work accidents caused by unsafe field conditions. In open mine area, there is often a slump due to unstable slopes, which can disrupt the activities and productivity of mining companies. Based on research on stability of open pit slopes conducted by Febrianti [8], the Meureubo coal mine located in Aceh Barat district, on the slope of mine was indicated unsafe slope conditions, it will be continued research on OSH for landslide which is to understand the stability of the excavation slope and the shape of the slope collapse. Plaxis software was used for this research. After analyzing the slope stability and the effect of landslide on OSH with Job Safety Analysis (JSA) method, to identify the hazard to work safety, risk management analysis will be conducted to classified hazard level and its handling technique. This research aim is to know the level of risk of work accident at the company and its prevention effort. The result of risk analysis research is very high-risk value that is > 350 then the activity must be stopped until the risk can be reduced to reach the risk value limit < 20 which is allowed or accepted.

  4. Analysis of dynamical response of air blast loaded safety device

    NASA Astrophysics Data System (ADS)

    Tropkin, S. N.; Tlyasheva, R. R.; Bayazitov, M. I.; Kuzeev, I. R.

    2018-03-01

    Equipment of many oil and gas processing plants in the Russian Federation is considerably worn-out. This causes the decrease of reliability and durability of equipment and rises the accident rate. An air explosion is the one of the most dangerous cases for plants in oil and gas industry, usually caused by uncontrolled emission and inflammation of oil products. Air explosion can lead to significant danger for life and health of plant staff, so it necessitates safety device usage. A new type of a safety device is designed. Numerical simulation is necessary to analyse design parameters and performance of the safety device, subjected to air blast loading. Coupled fluid-structure interaction analysis is performed to determine strength of the protective device and its performance. The coupled Euler-Lagrange method, allowable in Abaqus by SIMULIA, is selected as the most appropriate analysis tool to study blast wave interaction with the safety device. Absorption factors of blast wave are evaluated for the safety device. This factors allow one to assess efficiency of the safety device, and its main structural component – dampener. Usage of CEL allowed one to model fast and accurately the dampener behaviour, and to develop the parametric model to determine safety device sizes.

  5. 10 CFR 52.157 - Contents of applications; technical information in final safety analysis report.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... analysis of the structures, systems, and components of the reactor to be manufactured, with emphasis upon... assumed for this evaluation should be based upon a major accident, hypothesized for purposes of site... structures, systems, and components with the objective of assessing the risk to public health and safety...

  6. Consumer product safety: A systems problem

    NASA Technical Reports Server (NTRS)

    Clark, C. C.

    1971-01-01

    The manufacturer, tester, retailer, consumer, repairer disposer, trade and professional associations, national and international standards bodies, and governments in several roles are all involved in consumer product safety. A preliminary analysis, drawing on system safety techniques, is utilized to distinguish the inter-relations of these many groups and the responsibilities that they are or could take for product safety, including the slow accident hazards as well as the more commonly discussed fast accident hazards. The importance of interactive computer aided information flow among these groups is particularly stressed.

  7. The SAS4A/SASSYS-1 Safety Analysis Code System, Version 5

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Fanning, T. H.; Brunett, A. J.; Sumner, T.

    The SAS4A/SASSYS-1 computer code is developed by Argonne National Laboratory for thermal, hydraulic, and neutronic analysis of power and flow transients in liquidmetal- cooled nuclear reactors (LMRs). SAS4A was developed to analyze severe core disruption accidents with coolant boiling and fuel melting and relocation, initiated by a very low probability coincidence of an accident precursor and failure of one or more safety systems. SASSYS-1, originally developed to address loss-of-decay-heat-removal accidents, has evolved into a tool for margin assessment in design basis accident (DBA) analysis and for consequence assessment in beyond-design-basis accident (BDBA) analysis. SAS4A contains detailed, mechanistic models of transientmore » thermal, hydraulic, neutronic, and mechanical phenomena to describe the response of the reactor core, its coolant, fuel elements, and structural members to accident conditions. The core channel models in SAS4A provide the capability to analyze the initial phase of core disruptive accidents, through coolant heat-up and boiling, fuel element failure, and fuel melting and relocation. Originally developed to analyze oxide fuel clad with stainless steel, the models in SAS4A have been extended and specialized to metallic fuel with advanced alloy cladding. SASSYS-1 provides the capability to perform a detailed thermal/hydraulic simulation of the primary and secondary sodium coolant circuits and the balance-ofplant steam/water circuit. These sodium and steam circuit models include component models for heat exchangers, pumps, valves, turbines, and condensers, and thermal/hydraulic models of pipes and plena. SASSYS-1 also contains a plant protection and control system modeling capability, which provides digital representations of reactor, pump, and valve controllers and their response to input signal changes.« less

  8. Risk factors associated with traffic violations and accident severity in China.

    PubMed

    Zhang, Guangnan; Yau, Kelvin K W; Chen, Guanghan

    2013-10-01

    With the recent economic boom in China, vehicle volume and the number of traffic accident fatalities have become the highest in the world. Meanwhile, traffic accidents have become the leading cause of death in China. Systematically analyzing road safety data from different perspectives and applying empirical methods/implementing proper measures to reduce the fatality rate will be an urgent and challenging task for China in the coming years. In this study, we analyze the traffic accident data for the period 2006-2010 in Guangdong Province, China. These data, extracted from the Traffic Management Sector-Specific Incident Case Data Report, are the only officially available and reliable source of traffic accident data (with a sample size>7000 per year). In particular, we focus on two outcome measures: traffic violations and accident severity. Human, vehicle, road and environmental risk factors are considered. First, the results establish the role of traffic violations as one of the major risks threatening road safety. An immediate implication is: if the traffic violation rate could be reduced or controlled successfully, then the rate of serious injuries and fatalities would be reduced accordingly. Second, specific risk factors associated with traffic violations and accident severity are determined. Accordingly, to reduce traffic accident incidence and fatality rates, measures such as traffic regulations and legislation-targeting different vehicle types/driver groups with respect to the various human, vehicle and environment risk factors-are needed. Such measures could include road safety programs for targeted driver groups, focused enforcement of traffic regulations and road/transport facility improvements. Data analysis results arising from this study will shed lights on the development of similar (adjusted) measures to reduce traffic violations and/or accident fatalities and injuries, and to promote road safety in other regions. Copyright © 2013 Elsevier Ltd. All

  9. Data mining and visualization of the Alabama accident database

    DOT National Transportation Integrated Search

    2000-08-01

    The Alabama Department of Public Safety has developed and maintains a centralized database that contain traffic accident data collected from crash report completed by local police officers and state troopers. The Critical Analysis Reporting Environme...

  10. 49 CFR 195.54 - Accident reports.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Accident reports. 195.54 Section 195.54... PIPELINE Annual, Accident, and Safety-Related Condition Reporting § 195.54 Accident reports. (a) Each operator that experiences an accident that is required to be reported under § 195.50 shall as soon as...

  11. Integrated deterministic and probabilistic safety analysis for safety assessment of nuclear power plants

    DOE PAGES

    Di Maio, Francesco; Zio, Enrico; Smith, Curtis; ...

    2015-07-06

    The present special issue contains an overview of the research in the field of Integrated Deterministic and Probabilistic Safety Assessment (IDPSA) of Nuclear Power Plants (NPPs). Traditionally, safety regulation for NPPs design and operation has been based on Deterministic Safety Assessment (DSA) methods to verify criteria that assure plant safety in a number of postulated Design Basis Accident (DBA) scenarios. Referring to such criteria, it is also possible to identify those plant Structures, Systems, and Components (SSCs) and activities that are most important for safety within those postulated scenarios. Then, the design, operation, and maintenance of these “safety-related” SSCs andmore » activities are controlled through regulatory requirements and supported by Probabilistic Safety Assessment (PSA).« less

  12. Relationship between organizational justice and organizational safety climate: do fairness perceptions influence employee safety behaviour?

    PubMed

    Gyekye, Seth Ayim; Haybatollahi, Mohammad

    2014-01-01

    This study investigated the relationships between organizational justice, organizational safety climate, job satisfaction, safety compliance and accident frequency. Ghanaian industrial workers participated in the study (N = 320). Safety climate and justice perceptions were assessed with Hayes, Parender, Smecko, et al.'s (1998) and Blader and Tyler's (2003) scales respectively. A median split was performed to dichotomize participants into 2 categories: workers with positive and workers with negative justice perceptions. Confirmatory factors analysis confirmed the 5-factor structure of the safety scale. Regression analyses and t tests indicated that workers with positive fairness perceptions had constructive perspectives regarding workplace safety, expressed greater job satisfaction, were more compliant with safety policies and registered lower accident rates. These findings provide evidence that the perceived level of fairness in an organization is closely associated with workplace safety perception and other organizational factors which are important for safety. The implications for safety research are discussed.

  13. Major differences in rates of occupational accidents between different nationalities of seafarers.

    PubMed

    Hansen, Henrik L; Laursen, Lise Hedgaard; Frydberg, Morten; Kristensen, Soeren

    2008-01-01

    Earlier studies and statistics have shown that merchant seafarers from the South East Asia had considerable lower accident rates when compared with seafarers from Western Europe. The purposes of the study were to investigate whether the earlier observations were sustained if further sources on occurrence of accidents were used and to identify specific causes of excess accident rates among certain nationalities. Occupational accidents aboard Danish merchant ships during one year were identified from four different sources. These included accidents reported to the maritime authorities, accidents reported to a mutual insurance company, files on medical costs reimbursed by the government and finally, accidents in which there has been contact to the radio medical service. Time at risk aboard was obtained from a register on all employment periods aboard merchant ships. A total of 943 accidents causing personal injury to a seafarer directly caused by work aboard were identified. Among these accidents, 499 had taken place aboard cargo ships in international trade. Only these were used in the detailed analysis. The accident rate for all identified accidents aboard cargo ships were 84 accidents per 1,000 years aboard. The crude incidence rate ratio (IRR) for East European seafarers was 0.88 and for South East Asians 0.38 using West European seafarers as reference. In a Poisson regression analysis, the IRR for South East Asians was 0.29 (0.22-0.38). In an analysis including only more serious accidents, IRR for South East Asians rose to 0.36 (0.26-0.48). This study indicates that seafarers from South East Asia, mainly the Philippines, may have a genuine lower risk of occupational accidents in comparison with seafarers from Western and Eastern Europe. Differences in approach to safety and risk taking between South East Asian and European seafarers should be identified and positives attitudes included in accident preventing programmes. Main messages Seafarers from South East

  14. An Application of CICCT Accident Categories to Aviation Accidents in 1988-2004

    NASA Technical Reports Server (NTRS)

    Evans, Joni K.

    2007-01-01

    Interventions or technologies developed to improve aviation safety often focus on specific causes or accident categories. Evaluation of the potential effectiveness of those interventions is dependent upon mapping the historical aviation accidents into those same accident categories. To that end, the United States civil aviation accidents occurring between 1988 and 2004 (n=26,117) were assigned accident categories based upon the taxonomy developed by the CAST/ICAO Common Taxonomy Team (CICTT). Results are presented separately for four main categories of flight rules: Part 121 (large commercial air carriers), Scheduled Part 135 (commuter airlines), Non-Scheduled Part 135 (on-demand air taxi) and Part 91 (general aviation). Injuries and aircraft damage are summarized by year and by accident category.

  15. Safety of High Speed and Ground Guided Transportation Systems: Collision Avoidance and Accident Survivability: Volume 1: Collision Threat

    DOT National Transportation Integrated Search

    1993-03-01

    This report is the first of four volunes concerned with developing safety guidelines and specifications for high-speed : guided ground transportation (HSGGT) collision avoidance and accident survivability. The overall approach taken in this : study i...

  16. Safety Handbook.

    ERIC Educational Resources Information Center

    Montgomery County Public Schools, Rockville, MD.

    Safety policies, procedures, and related information are presented in this manual to assist school personnel in a continuing program of accident prevention. Chapter 1 discusses safety education and accident prevention in general. Chapter 2 covers traffic regulations relating to school safety patrols, school bus transportation, bicycles, and…

  17. Final safety analysis report for the Ground Test Accelerator (GTA), Phase 2

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    NONE

    1994-10-01

    This document is the second volume of a 3 volume safety analysis report on the Ground Test Accelerator (GTA). The GTA program at the Los Alamos National Laboratory (LANL) is the major element of the national Neutral Particle Beam (NPB) program, which is supported by the Strategic Defense Initiative Office (SDIO). A principal goal of the national NPB program is to assess the feasibility of using hydrogen and deuterium neutral particle beams outside the Earth`s atmosphere. The main effort of the NPB program at Los Alamos concentrates on developing the GTA. The GTA is classified as a low-hazard facility, exceptmore » for the cryogenic-cooling system, which is classified as a moderate-hazard facility. This volume consists of failure modes and effects analysis; accident analysis; operational safety requirements; quality assurance program; ES&H management program; environmental, safety, and health systems critical to safety; summary of waste-management program; environmental monitoring program; facility expansion, decontamination, and decommissioning; summary of emergency response plan; summary plan for employee training; summary plan for operating procedures; glossary; and appendices A and B.« less

  18. Secondary school accident reporting in one education authority.

    PubMed

    Williams, W R; Latif, A H A; Sibert, J

    2002-01-01

    Secondary schools appear to have very different accident rates when they are compared on the basis of accident report returns. The variation may be as a result of real differences in accident rates or different reporting procedures. This study investigates accident reporting from secondary schools and, in particular, the role of the school nurse. Accident form returns covering a 2-year period were collected for statistical analysis from 13 comprehensive schools in one local education authority in Wales. School sites were visited in the following school year to obtain information about accident records held on site and accident reporting procedures. The main factors determining the number of school accident reports submitted to the education authority relate to differences in recording and reporting procedures, such as the employment of a nurse and the policy of the head teacher/safety officer on submitting accident returns. Accident and emergency department referrals from similar schools may show significant differences in specific injuries and their causes. The level of school accident activity cannot be gauged from reports submitted to the education authority. Lack of incentives for collecting good accident data, in conjunction with the degree of complacency in the current system, suggest that future accident rates and reporting activity are unlikely to change.

  19. Workplace accidents and self-organized criticality

    NASA Astrophysics Data System (ADS)

    Mauro, John C.; Diehl, Brett; Marcellin, Richard F.; Vaughn, Daniel J.

    2018-09-01

    The occurrence of workplace accidents is described within the context of self-organized criticality, a theory from statistical physics that governs a wide range of phenomena across physics, biology, geosciences, economics, and the social sciences. Workplace accident data from the U.S. Bureau of Labor Statistics reveal a power-law relationship between the number of accidents and their severity as measured by the number of days lost from work. This power-law scaling is indicative of workplace accidents being governed by self-organized criticality, suggesting that nearly all workplace accidents have a common underlying cause, independent of their severity. Such power-law scaling is found for all labor categories documented by the U.S. Bureau of Labor Statistics. Our results provide scientific support for the Heinrich accident triangle, with the practical implication that suppressing the rate of severe accidents requires changing the attitude toward workplace safety in general. By creating a culture that values safety, empowers individuals, and strives to continuously improve, accident rates can be suppressed across the full range of severities.

  20. Analysis of traffic accident data in Kentucky (1986-1990)

    DOT National Transportation Integrated Search

    1991-09-01

    This report includes an analysis of traffic accident data in Kentucky for the years of 1986-1990. A primary objectve of this study was to determine average statistics for kentucky highways. Average and critical number and rates of accidents were calc...

  1. Analysis of traffic accident data in Kentucky (1994-1998)

    DOT National Transportation Integrated Search

    1999-09-01

    This report includes an analysis of traffic accident data in Kentucky for the years of 1994 through 1998. A primary objective of this study was to determine average accident statistics for Kentucky highways. Average and critical numbers and rates of ...

  2. Survivors Perceptions of Recovery following Air Medical Transport Accidents.

    PubMed

    Jaynes, Cathy L; Valdez, Anna; Hamilton, Megan; Haugen, Krista; Henry, Colin; Jones, Pat; Werman, Howard A; White, Lynn J

    2015-01-01

    Abstract Objective: Air medical transport (AMT) teams play an essential role in the care of the critically ill and injured. Their work, however, is not without risk. Since the inception of the industry numerous AMT accidents have been reported. The objective of this research is to gain a better understanding of the post-accident sequelae for professionals who have survived AMT accidents. The hope is that this understanding will empower the industry to better support survivors and plan for the contingencies of post-accident recovery. Methods: Qualitative methods were used to explore the experience of flight crew members who have survived an AMT accident. "Accident" was defined using criteria established by the National Transportation Safety Board. Traditional focus group methodology explored the survivors' experiences following the accident. Results: Seven survivors participated in the focus group. Content analysis revealed themes in four major domains that described the experience of survivors: Physical, Psychological, Relational and Financial. Across the themes survivors reported that industry and company response varied greatly, ranging from generous support, understanding and action to make safety improvements, to little response or action and lack of attention to survivor needs. Conclusion: Planning for AMT post-accident response was identified to be lacking in scope and quality. More focused efforts are needed to assist and support the survivors as they regain both their personal and professional lives following the accident. This planning should include all stakeholders in safe transport; the individual crewmember, air medical transport companies, and the industry at large.

  3. The Fukushima Dai-ichi Accident and its implications for the safety of nuclear power

    NASA Astrophysics Data System (ADS)

    Barletta, William

    2016-05-01

    Five years ago the dramatic events in Fukushima that followed the massive earthquake and subsequent tsunami that struck Japan on March 11, 2011 sharpened the focus of scientists, engineers and general public on the broad range of technical, environmental and societal issues involved in assuring the safety of the world's nuclear power complex. They also called into question the potential of nuclear power to provide a growing, sustainable resource of CO2-free energy. The issues raised by Fukushima Dai-ichi have provoked urgent concern, not only because of the potential harm that could result from severe accidents or from intentional damage to nuclear reactors or to facilities involved in the nuclear fuel cycle, but also because of the extensive economic impact of those accidents and of the measures taken to avoid them.

  4. Analysis of traffic accident data in Kentucky (1995-1999)

    DOT National Transportation Integrated Search

    2000-09-01

    This report includes an analysis of traffic accidents data in Kentucky for the year 1995-1999. A primary objective of this study was to determined average and critical numbers and rates of accidents for various types of highways in rural and urban ar...

  5. Student Accidents in Hawaii's Public Schools.

    ERIC Educational Resources Information Center

    Taketa, Sachiko

    1984-01-01

    Review of data collected from student accident report forms in Hawaii public schools revealed that the intermediate grade level had the highest number of school accidents. The significant number of accidents and school days lost may warrant the need for better safety education. (Author/DF)

  6. Safety Analysis and Protection Measures of the Control System of the Pulsed High Magnetic Field Facility in WHMFC

    NASA Astrophysics Data System (ADS)

    Shi, J. T.; Han, X. T.; Xie, J. F.; Yao, L.; Huang, L. T.; Li, L.

    2013-03-01

    A Pulsed High Magnetic Field Facility (PHMFF) has been established in Wuhan National High Magnetic Field Center (WHMFC) and various protection measures are applied in its control system. In order to improve the reliability and robustness of the control system, the safety analysis of the PHMFF is carried out based on Fault Tree Analysis (FTA) technique. The function and realization of 5 protection systems, which include sequence experiment operation system, safety assistant system, emergency stop system, fault detecting and processing system and accident isolating protection system, are given. The tests and operation indicate that these measures improve the safety of the facility and ensure the safety of people.

  7. Context-aware system for pre-triggering irreversible vehicle safety actuators.

    PubMed

    Böhmländer, Dennis; Dirndorfer, Tobias; Al-Bayatti, Ali H; Brandmeier, Thomas

    2017-06-01

    New vehicle safety systems have led to a steady improvement of road safety and a reduction in the risk of suffering a major injury in vehicle accidents. A huge leap forward in the development of new vehicle safety systems are actuators that have to be activated irreversibly shortly before a collision in order to mitigate accident consequences. The triggering decision has to be based on measurements of exteroceptive sensors currently used in driver assistance systems. This paper focuses on developing a novel context-aware system designed to detect potential collisions and to trigger safety actuators even before an accident occurs. In this context, the analysis examines the information that can be collected from exteroceptive sensors (pre-crash data) to predict a certain collision and its severity to decide whether a triggering is entitled or not. A five-layer context-aware architecture is presented, that is able to collect contextual information about the vehicle environment and the actual driving state using different sensors, to perform reasoning about potential collisions, and to trigger safety functions upon that information. Accident analysis is used in a data model to represent uncertain knowledge and to perform reasoning. A simulation concept based on real accident data is introduced to evaluate the presented system concept. Copyright © 2017 Elsevier Ltd. All rights reserved.

  8. Using Occupational Safety and Health Administration accident investigations to study patterns in work fatalities.

    PubMed

    Mendeloff, J M; Kagey, B T

    1990-11-01

    Investigations of fatalities by the Occupational Safety and Health Administration (OSHA) provide the most detailed available information about traumatic workplace deaths that are potentially related to violations of existing safety standards. Comparison of the number of such deaths investigated by OSHA from 1977 to 1986 with the comparable category of deaths reported to the Bureau of Labor Statistics Survey of Occupational Injuries and Illnesses indicates that the overall magnitudes have been roughly similar. The OSHA data contain more information than other sources and are especially valuable for analyses of fatalities at smaller workplaces. The OSHA data show that death rates decline sharply with establishment size; the inverted "U" pattern for lost workday injury rates is absent. Because accident investigations are conducted as part of an administrative system, the OSHA data can be influenced by changes in administrative policies. Changes over time in the percent of fatalities in which violations of OSHA standards were cited have clearly been influenced by changes in OSHA citation policy and thus do not provide a valid measure of the rate of violation-caused deaths. Realization of the epidemiological value of this data source depends upon a commitment from OSHA to maintain consistency in investigating accidents and to improve its data collection methods.

  9. [An analysis of 148 outpatient treated occupational accidents].

    PubMed

    Nicaeus, T; Erb, C; Rohrbach, M; Thiel, H J

    1996-10-01

    The most common eye injuries are non-perforating. Eye injuries in the workplace are a major cause of socioeconomical damage, morbidity and disability, despite well publicised standards for industrial eye protection. This study investigates the epidemiological and clinical aspects of 148 occupational cases. At the University Eye Clinic of Tübingen, 709 non-perforating eye injuries were registered as occupational accidents between 1995 and 1996. Of these cases, 148 were analysed retrospectively per random. The 5 most common injuries of 148 patients (m/f = 138/10; mean age 33.4 +/- 12 years) were related to corneal foreign body injuries (35%), chemical burns (15.5%), sub-conjunctival foreign bodies (12%), thermal/ultraviolet injuries (11%) and contusions (7.4%). Of these patients, 22.3% were employed as construction workers and 16.2% as metal workers. At the time of examination the visual acuity of the traumatic eye was 0.9 +/- 0.3. The interval between the beginning of work and accident was 6.2 +/- 6.4 hours in average (0.5-13.5 h). Of all accidents, 8.5% were caused during the first hour of work; in contrast 45.5% of all accidents were caused after 6 hours of work. Another 12.4 +/- 14.5 hours (5min.-72 h; median 7 h) passed by until the patients arrived for eye examination at the Eye Clinic of Tübingen. Only 6% of all patients arrived within the first hour, and 29.7% after 12 hours. Of all cases, 30.4% received first-aid treatment in their company by the factory doctor or by the eye doctor before examination at the Eye Clinic. Only 6.8% of all patients had protective spectacles during work. Incapacity was seen in 30.4%; the average in total was 5.5 +/- 10 days. Despite the late examination at the Eye Clinic the functional loss was mostly little except after chemical burns. Nevertheless, most occupational accidents can be avoided with better protective devices in order to reduce the incidence of injuries and socioeconomical damage. Therefore an intense campaign

  10. Selecting Strategies to Reduce High-Risk Unsafe Work Behaviors Using the Safety Behavior Sampling Technique and Bayesian Network Analysis.

    PubMed

    Ghasemi, Fakhradin; Kalatpour, Omid; Moghimbeigi, Abbas; Mohammadfam, Iraj

    2017-03-04

    High-risk unsafe behaviors (HRUBs) have been known as the main cause of occupational accidents. Considering the financial and societal costs of accidents and the limitations of available resources, there is an urgent need for managing unsafe behaviors at workplaces. The aim of the present study was to find strategies for decreasing the rate of HRUBs using an integrated approach of safety behavior sampling technique and Bayesian networks analysis. A cross-sectional study. The Bayesian network was constructed using a focus group approach. The required data was collected using the safety behavior sampling, and the parameters of the network were estimated using Expectation-Maximization algorithm. Using sensitivity analysis and belief updating, it was determined that which factors had the highest influences on unsafe behavior. Based on BN analyses, safety training was the most important factor influencing employees' behavior at the workplace. High quality safety training courses can reduce the rate of HRUBs about 10%. Moreover, the rate of HRUBs increased by decreasing the age of employees. The rate of HRUBs was higher in the afternoon and last days of a week. Among the investigated variables, training was the most important factor affecting safety behavior of employees. By holding high quality safety training courses, companies would be able to reduce the rate of HRUBs significantly.

  11. Traffic accidents on expressways: new threat to China.

    PubMed

    Zhao, Jinbao; Deng, Wei

    2012-01-01

    As China is building one of the largest expressway systems in the world, expressway safety problems have become serious concerns to China. This article analyzed the trends in expressway accidents in China from 1995 to 2010 and examined the characteristics of these accidents. Expressway accident data were obtained from the Annual Report for Road Traffic Accidents published by the Ministry of Public Security of China. Expressway mileage data were obtained from the National Statistics Yearbook published by the National Bureau of Statistics of China. Descriptive statistical analyses were conducted based on these data. Expressway deaths increased by 10.2-fold from 616 persons in 1995 to 6300 persons in 2010, and the average annual increase was 17.9 percent over the past 15 years, and the overall other road traffic deaths was -0.33 percent. China's expressway mileage accounted for only 1.85 percent of highway mileage driven in 2010, but expressway deaths made up 13.54 percent of highway traffic deaths. The average annual accident lethality rate [accident deaths/(accident deaths + accident injuries)] for China's expressways was 27.76 percent during the period 1995 to 2010, which was 1.33 times higher than the accident lethality rate of highway traffic accidents. China's government should pay attention to expressway construction and safety interventions during the rapid development period of expressways. Related causes, such as geographic patterns, speeding, weather conditions, and traffic flow composition, need to be studied in the near future. An effective and scientific expressway safety management services system, composed of a speed monitoring system, warning system, and emergency rescue system, should be established in developed and underdeveloped provinces in China to improve safety on expressway.

  12. Professional Preparation for Careers in Safety.

    ERIC Educational Resources Information Center

    Della-Giustina, Daniel

    There has been a long existing need for individuals with extensive training and concentration in safety studies. The foundation areas upon which a curriculum for training safety practitioners is based should include: (1) trends in accident prevention and control; (2) safety analysis of human and machine tasks; (3) hazard identification and control…

  13. Accident Precursor Analysis and Management: Reducing Technological Risk Through Diligence

    NASA Technical Reports Server (NTRS)

    Phimister, James R. (Editor); Bier, Vicki M. (Editor); Kunreuther, Howard C. (Editor)

    2004-01-01

    Almost every year there is at least one technological disaster that highlights the challenge of managing technological risk. On February 1, 2003, the space shuttle Columbia and her crew were lost during reentry into the atmosphere. In the summer of 2003, there was a blackout that left millions of people in the northeast United States without electricity. Forensic analyses, congressional hearings, investigations by scientific boards and panels, and journalistic and academic research have yielded a wealth of information about the events that led up to each disaster, and questions have arisen. Why were the events that led to the accident not recognized as harbingers? Why were risk-reducing steps not taken? This line of questioning is based on the assumption that signals before an accident can and should be recognized. To examine the validity of this assumption, the National Academy of Engineering (NAE) undertook the Accident Precursors Project in February 2003. The project was overseen by a committee of experts from the safety and risk-sciences communities. Rather than examining a single accident or incident, the committee decided to investigate how different organizations anticipate and assess the likelihood of accidents from accident precursors. The project culminated in a workshop held in Washington, D.C., in July 2003. This report includes the papers presented at the workshop, as well as findings and recommendations based on the workshop results and committee discussions. The papers describe precursor strategies in aviation, the chemical industry, health care, nuclear power and security operations. In addition to current practices, they also address some areas for future research.

  14. NASA Structural Analysis Report on the American Airlines Flight 587 Accident - Local Analysis of the Right Rear Lug

    NASA Technical Reports Server (NTRS)

    Raju, Ivatury S; Glaessgen, Edward H.; Mason, Brian H; Krishnamurthy, Thiagarajan; Davila, Carlos G

    2005-01-01

    A detailed finite element analysis of the right rear lug of the American Airlines Flight 587 - Airbus A300-600R was performed as part of the National Transportation Safety Board s failure investigation of the accident that occurred on November 12, 2001. The loads experienced by the right rear lug are evaluated using global models of the vertical tail, local models near the right rear lug, and a global-local analysis procedure. The right rear lug was analyzed using two modeling approaches. In the first approach, solid-shell type modeling is used, and in the second approach, layered-shell type modeling is used. The solid-shell and the layered-shell modeling approaches were used in progressive failure analyses (PFA) to determine the load, mode, and location of failure in the right rear lug under loading representative of an Airbus certification test conducted in 1985 (the 1985-certification test). Both analyses were in excellent agreement with each other on the predicted failure loads, failure mode, and location of failure. The solid-shell type modeling was then used to analyze both a subcomponent test conducted by Airbus in 2003 (the 2003-subcomponent test) and the accident condition. Excellent agreement was observed between the analyses and the observed failures in both cases. From the analyses conducted and presented in this paper, the following conclusions were drawn. The moment, Mx (moment about the fuselage longitudinal axis), has significant effect on the failure load of the lugs. Higher absolute values of Mx give lower failure loads. The predicted load, mode, and location of the failure of the 1985-certification test, 2003-subcomponent test, and the accident condition are in very good agreement. This agreement suggests that the 1985-certification and 2003- subcomponent tests represent the accident condition accurately. The failure mode of the right rear lug for the 1985-certification test, 2003-subcomponent test, and the accident load case is identified as a

  15. Auto Accidents: Reducing Frequency, Increasing Recovery.

    ERIC Educational Resources Information Center

    Comeaux, Linda Atkins

    1988-01-01

    Careful hiring, monitoring, training, discipline, and safety policies will reduce school automobile and bus accidents. Guidelines are offered for accident reporting, claim handling, and dealing with insurance adjusters. (MLF)

  16. Heterogeneity of road traffic accident rate in the Russian cities and the need of usage various methods of transport safety management

    NASA Astrophysics Data System (ADS)

    Petrov, A. I.; Petrova, D. A.

    2017-10-01

    The article considers one of the topical problems of road safety management at the federal level - the problem of the heterogeneity of road traffic accident rate in Russian cities. The article analyzes actual statistical data on road traffic accident rate in the administrative centers of Russia. The histograms of the distribution of the values of two most important road accidents characteristics - Social Risk HR and Severity Rate of Road Accidents - formed in 2016 in administrative centers of Russia are presented. On the basis of the regression model of the statistical connection between Severity Rate of Road Accidents and Social Risk HR, a classification of the Russian cities based on the level of actual road traffic accident rate was developed. On the basis of this classification a differentiated system of priority methods for organizing the safe functioning of transport systems in the cities of Russia is proposed.

  17. APT Blanket System Loss-of-Coolant Accident (LOCA) Analysis Based on Initial Conceptual Design - Case 3: External HR Break at Pump Outlet without Pump Trip

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Hamm, L.L.

    1998-10-07

    This report is one of a series of reports that document normal operation and accident simulations for the Accelerator Production of Tritium (APT) blanket heat removal (HR) system. These simulations were performed for the Preliminary Safety Analysis Report.

  18. 49 CFR 801.32 - Accident reports.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 7 2010-10-01 2010-10-01 false Accident reports. 801.32 Section 801.32 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL TRANSPORTATION SAFETY BOARD PUBLIC AVAILABILITY OF INFORMATION Accident Investigation Records § 801.32 Accident reports. (a) The NTSB will report the facts, conditions, and...

  19. Analysis of factors influencing safety management for metro construction in China.

    PubMed

    Yu, Q Z; Ding, L Y; Zhou, C; Luo, H B

    2014-07-01

    With the rapid development of urbanization in China, the number and size of metro construction projects are increasing quickly. At the same time, and increasing number of accidents in metro construction make it a disturbing focus of social attention. In order to improve safety management in metro construction, an investigation of the participants' perspectives on safety factors in China metro construction has been conducted to identify the key safety factors, and their ranking consistency among the main participants, including clients, consultants, designers, contractors and supervisors. The result of factor analysis indicates that there are five key factors which influence the safety of metro construction including safety attitude, construction site safety, government supervision, market restrictions and task unpredictability. In addition, ANOVA and Spearman rank correlation coefficients were performed to test the consistency of the means rating and the ranking of safety factors. The results indicated that the main participants have significant disagreement about the importance of safety factors on more than half of the items. Suggestions and recommendations on practical countermeasures to improve metro construction safety management in China are proposed. Copyright © 2013 Elsevier Ltd. All rights reserved.

  20. [An analysis of industrial accidents in the working field with a particular emphasis on repeated accidents].

    PubMed

    Wakisaka, I; Yanagihashi, T; Tomari, T; Sato, M

    1990-03-01

    The present study is based on an analysis of routinely submitted reports of occupational accidents experienced by the workers of industrial enterprises under the jurisdiction of Kagoshima Labor Standard Office during a 5-year period 1983 to 1987. Officially notified injuries serious enough to keep employees away from their job for work at least 4 days were utilized in this study. Data was classified so as to give an observed frequency distribution for workers having any specified number of accidents. Also, the accident rate which is an indicator of the risk of accident was compared among different occupations, between age groups and between the sexes. Results obtained are as follows; 1) For the combined total of 6,324 accident cases for 8 types of occupation (Construction, Transportation, Mining & Quarrying, Forestry, Food manufacture, Lumber & Woodcraft, Manufacturing industry and Other business), the number of those who had at least one accident was 6,098, of which 5,837 were injured only once, 208 twice, 21 three times and 2 four times. When occupation type was fixed, however, the number of workers having one, two, three and four times of accidents were 5,895, 182, 19 and 2, respectively. This suggests that some workers are likely to have experienced repeated accidents in more than one type of occupation.(ABSTRACT TRUNCATED AT 250 WORDS)

  1. 49 CFR 801.30 - Records from accident investigations.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 7 2010-10-01 2010-10-01 false Records from accident investigations. 801.30... TRANSPORTATION SAFETY BOARD PUBLIC AVAILABILITY OF INFORMATION Accident Investigation Records § 801.30 Records from accident investigations. Upon completion of an accident investigation, each NTSB investigator (or...

  2. 49 CFR 801.30 - Records from accident investigations.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 7 2011-10-01 2011-10-01 false Records from accident investigations. 801.30... TRANSPORTATION SAFETY BOARD PUBLIC AVAILABILITY OF INFORMATION Accident Investigation Records § 801.30 Records from accident investigations. Upon completion of an accident investigation, each NTSB investigator (or...

  3. Quantification method analysis of the relationship between occupant injury and environmental factors in traffic accidents.

    PubMed

    Ju, Yong Han; Sohn, So Young

    2011-01-01

    Injury analysis following a vehicle crash is one of the most important research areas. However, most injury analyses have focused on one-dimensional injury variables, such as the AIS (Abbreviated Injury Scale) or the IIS (Injury Impairment Scale), at a time in relation to various traffic accident factors. However, these studies cannot reflect the various injury phenomena that appear simultaneously. In this paper, we apply quantification method II to the NASS (National Automotive Sampling System) CDS (Crashworthiness Data System) to find the relationship between the categorical injury phenomena, such as the injury scale, injury position, and injury type, and the various traffic accident condition factors, such as speed, collision direction, vehicle type, and seat position. Our empirical analysis indicated the importance of safety devices, such as restraint equipment and airbags. In addition, we found that narrow impact, ejection, air bag deployment, and higher speed are associated with more severe than minor injury to the thigh, ankle, and leg in terms of dislocation, abrasion, or laceration. Copyright © 2010 Elsevier Ltd. All rights reserved.

  4. NASA Aviation Safety Program Systems Analysis/Program Assessment Metrics Review

    NASA Technical Reports Server (NTRS)

    Louis, Garrick E.; Anderson, Katherine; Ahmad, Tisan; Bouabid, Ali; Siriwardana, Maya; Guilbaud, Patrick

    2003-01-01

    The goal of this project is to evaluate the metrics and processes used by NASA's Aviation Safety Program in assessing technologies that contribute to NASA's aviation safety goals. There were three objectives for reaching this goal. First, NASA's main objectives for aviation safety were documented and their consistency was checked against the main objectives of the Aviation Safety Program. Next, the metrics used for technology investment by the Program Assessment function of AvSP were evaluated. Finally, other metrics that could be used by the Program Assessment Team (PAT) were identified and evaluated. This investigation revealed that the objectives are in fact consistent across organizational levels at NASA and with the FAA. Some of the major issues discussed in this study which should be further investigated, are the removal of the Cost and Return-on-Investment metrics, the lack of the metrics to measure the balance of investment and technology, the interdependencies between some of the metric risk driver categories, and the conflict between 'fatal accident rate' and 'accident rate' in the language of the Aviation Safety goal as stated in different sources.

  5. Relationship between road traffic accidents and conflicts recorded by drive recorders.

    PubMed

    Lu, Guangquan; Cheng, Bo; Kuzumaki, Seigo; Mei, Bingsong

    2011-08-01

    Road traffic conflicts can be used to estimate the probability of accident occurrence, assess road safety, or evaluate road safety programs if the relationship between road traffic accidents and conflicts is known. To this end, we propose a model for the relationship between road traffic accidents and conflicts recorded by drive recorders (DRs). DRs were installed in 50 cars in Beijing to collect records of traffic conflicts. Data containing 1366 conflicts were collected in 193 days. The hourly distributions of conflicts and accidents were used to model the relationship between accidents and conflicts. To eliminate time series and base number effects, we defined and used 2 parameters: average annual number of accidents per 10,000 vehicles per hour and average number of conflicts per 10,000 vehicles per hour. A model was developed to describe the relationship between the two parameters. If A(i) = average annual number of accidents per 10,000 vehicles per hour at hour i, and E(i) = average number of conflicts per 10,000 vehicles per hour at hour i, the relationship can be expressed as [Formula in text] (α>0, β>0). The average number of traffic accidents increases as the number of conflicts rises, but the rate of increase decelerates as the number of conflicts increases further. The proposed model can describe the relationship between road traffic accidents and conflicts in a simple manner. According to our analysis, the model fits the present data.

  6. A Comprehensive Analysis of the X-15 Flight 3-65 Accident

    NASA Technical Reports Server (NTRS)

    Dennehy, Cornelius J.; Orr, Jeb S.; Barshi, Immanuel; Statler, Irving C.

    2014-01-01

    The November 15, 1967, loss of X-15 Flight 3-65-97 (hereafter referred to as Flight 3-65) was a unique incident in that it was the first and only aerospace flight accident involving loss of crew on a vehicle with an adaptive flight control system (AFCS). In addition, Flight 3-65 remains the only incidence of a single-pilot departure from controlled flight of a manned entry vehicle in a hypersonic flight regime. To mitigate risk to emerging aerospace systems, the NASA Engineering and Safety Center (NESC) proposed a comprehensive review of this accident. The goal of the assessment was to resolve lingering questions regarding the failure modes of the aircraft systems (including the AFCS) and thoroughly analyze the interactions among the human agents and autonomous systems that contributed to the loss of the pilot and aircraft. This document contains the outcome of the accident review.

  7. Coal Canyon Fire: Serious Accident Investigation Report

    Treesearch

    Charles L. Myers; Randy Draeger; Antoine Dixon; Cliff Dahl; Jim Saveland; Brad Mayhew; Gary Brown; Tony Petrilli; Ben Murphy; Erin Newman; Karen Mora; Tim Foley

    2012-01-01

    The purpose of this report is to present the facts proximal to the accident and share the Team's analysis in a way that enhances the reliability and resilience of Federal, State, and Local wildland fire organizations. The intent is to spur discussion and learning for those in the fire and safety community at all levels.

  8. Errors in accident data, its types, causes and methods of rectification-analysis of the literature.

    PubMed

    Ahmed, Ashar; Sadullah, Ahmad Farhan Mohd; Yahya, Ahmad Shukri

    2017-07-29

    Most of the decisions taken to improve road safety are based on accident data, which makes it the back bone of any country's road safety system. Errors in this data will lead to misidentification of black spots and hazardous road segments, projection of false estimates pertinent to accidents and fatality rates, and detection of wrong parameters responsible for accident occurrence, thereby making the entire road safety exercise ineffective. Its extent varies from country to country depending upon various factors. Knowing the type of error in the accident data and the factors causing it enables the application of the correct method for its rectification. Therefore there is a need for a systematic literature review that addresses the topic at a global level. This paper fulfils the above research gap by providing a synthesis of literature for the different types of errors found in the accident data of 46 countries across the six regions of the world. The errors are classified and discussed with respect to each type and analysed with respect to income level; assessment with regard to the magnitude for each type is provided; followed by the different causes that result in their occurrence, and the various methods used to address each type of error. Among high-income countries the extent of error in reporting slight, severe, non-fatal and fatal injury accidents varied between 39-82%, 16-52%, 12-84%, and 0-31% respectively. For middle-income countries the error for the same categories varied between 93-98%, 32.5-96%, 34-99% and 0.5-89.5% respectively. The only four studies available for low-income countries showed that the error in reporting non-fatal and fatal accidents varied between 69-80% and 0-61% respectively. The logistic relation of error in accident data reporting, dichotomised at 50%, indicated that as the income level of a country increases the probability of having less error in accident data also increases. Average error in recording information related to the

  9. Root causes and impacts of severe accidents at large nuclear power plants.

    PubMed

    Högberg, Lars

    2013-04-01

    The root causes and impacts of three severe accidents at large civilian nuclear power plants are reviewed: the Three Mile Island accident in 1979, the Chernobyl accident in 1986, and the Fukushima Daiichi accident in 2011. Impacts include health effects, evacuation of contaminated areas as well as cost estimates and impacts on energy policies and nuclear safety work in various countries. It is concluded that essential objectives for reactor safety work must be: (1) to prevent accidents from developing into severe core damage, even if they are initiated by very unlikely natural or man-made events, and, recognizing that accidents with severe core damage may nevertheless occur; (2) to prevent large-scale and long-lived ground contamination by limiting releases of radioactive nuclides such as cesium to less than about 100 TBq. To achieve these objectives the importance of maintaining high global standards of safety management and safety culture cannot be emphasized enough. All three severe accidents discussed in this paper had their root causes in system deficiencies indicative of poor safety management and poor safety culture in both the nuclear industry and government authorities.

  10. 48 CFR 1836.513 - Accident prevention.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 48 Federal Acquisition Regulations System 6 2011-10-01 2011-10-01 false Accident prevention. 1836... 1836.513 Accident prevention. The contracting officer must insert the clause at 1852.223-70, Safety and Health, in lieu of FAR clause 52.236-13, Accident Prevention, and its Alternate I. [67 FR 17016, Apr. 9...

  11. 48 CFR 1836.513 - Accident prevention.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 6 2010-10-01 2010-10-01 true Accident prevention. 1836... 1836.513 Accident prevention. The contracting officer must insert the clause at 1852.223-70, Safety and Health, in lieu of FAR clause 52.236-13, Accident Prevention, and its Alternate I. [67 FR 17016, Apr. 9...

  12. 49 CFR 845.40 - Accident report.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 7 2010-10-01 2010-10-01 false Accident report. 845.40 Section 845.40 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL TRANSPORTATION SAFETY BOARD RULES OF PRACTICE IN TRANSPORTATION; ACCIDENT/INCIDENT HEARINGS AND REPORTS Board Reports § 845.40 Accident report. (a) The Board will issue a detailed...

  13. Extracting decision rules from police accident reports through decision trees.

    PubMed

    de Oña, Juan; López, Griselda; Abellán, Joaquín

    2013-01-01

    Given the current number of road accidents, the aim of many road safety analysts is to identify the main factors that contribute to crash severity. To pinpoint those factors, this paper shows an application that applies some of the methods most commonly used to build decision trees (DTs), which have not been applied to the road safety field before. An analysis of accidents on rural highways in the province of Granada (Spain) between 2003 and 2009 (both inclusive) showed that the methods used to build DTs serve our purpose and may even be complementary. Applying these methods has enabled potentially useful decision rules to be extracted that could be used by road safety analysts. For instance, some of the rules may indicate that women, contrary to men, increase their risk of severity under bad lighting conditions. The rules could be used in road safety campaigns to mitigate specific problems. This would enable managers to implement priority actions based on a classification of accidents by types (depending on their severity). However, the primary importance of this proposal is that other databases not used here (i.e. other infrastructure, roads and countries) could be used to identify unconventional problems in a manner easy for road safety managers to understand, as decision rules. Copyright © 2012 Elsevier Ltd. All rights reserved.

  14. Commuter Train Passenger Safety Model Using Positive Behavior Approach: The Case Study in Suburban Area

    NASA Astrophysics Data System (ADS)

    Suryanto, D. A.; Adisasmita, S. A.; Hamid, S.; Hustim, M.

    2018-04-01

    Currently, Train passanger safety measures are more predominantly measurable using negative dimensions in user mode behavior, such as accident rate, accident intensity and accident impact. This condition suggests that safety improvements aim only to reduce accidents. Therefore, this study aims to measure the safety level of light train transit modes (KRL) through the dimensions of traveling safety on commuters based on positive safety indicators with severel condition departure times and returns for work purposes and long trip rates above KRL. The primary survey were used in data collection methods. Structural Equation Modeling (SEM) were used in data analysis. The results show that there are different models of the safety level of departure and return journey. The highest difference is in the security dimension which is the internal variable of KRL users.

  15. [Accidents on Iceland's most dangerous roads].

    PubMed

    Bjarnason, Thóroddur; Arnarsson, Sveinn

    2012-02-01

    The objective of this paper was to identify the most dangerous segments of the Icelandic road system in terms of the number of accidents pr km and the rate of accidents pr million km travelled. First to identify the segments where the number of accidents is highest and where the risk of the individual traveller is the greatest. Second to evaluate if the association between the number and the rate of accidents is positive or negative. Third to identify the road segments that are the most dangerous in the sense of many accidents and great risk to individual travellers. Main roads outside urban centers were divided into 45 segments that were on average 78 km in length. Infrequently travelled roads and roads within urban centers were omitted. Information on the length of roads, traffic density and number of accidents was used to calculate the number of accidents per km and the rate of accidents per million km travelled. The correlation between the number and rate of accidents was calculated and the most dangerous road segments were identified by the average rank order on both dimensions. Most accidents pr km occurred on the main roads to and from the capital region, but also east towards Hvolsvöllur, north towards Akureyri and in the Mideast region of the country. The rate of accidents pr million km travelled was highest in the northeast region, in northern Snæfellsnes and in the Westfjords. The most dangerous roads on both dimensions were in Mideast, northern Westfjords, in the north between Blönduós and Akureyri and in northern Snæfellsnes. Most accidents pr km occurred on roads with a low accident rate pr million km travelled. It is therefore possible to reduce accidents the most by increasing road safety where it is already the greatest but that would however increase inequalities in road safety. Policy development in transportation is therefore in part a question of priorities in healthcare. Individual equality in safety and health are not always fully

  16. Lessons Learned for Space Safety from the Fukushima Nuclear Power Plant Accident

    NASA Astrophysics Data System (ADS)

    Nogami, Manami; Miki, Masami; Mitsui, Masami; Kawada, Ysuhiro; Takeuchi, Nobuo

    2013-09-01

    On March 11 2011, Tohoku Region Pacific Coast Earthquake hit Japan and caused the devastating damage. The Fukushima Nuclear Power Station (NPS) was also severely damaged.The Japanese NPSs are designed based on the detailed safety requirements and have multiple-folds of hazard controls to the catastrophic hazards as in space system. However, according to the initial information from the Tokyo Electric Power Company (TEPCO) and the Japanese government, the larger-than-expected tsunami and subsequent events lost the all hazard controls to the release of radioactive materials.At the 5th IAASS, Lessons Learned from this disaster was reported [1] mainly based on the "Report of the Japanese Government to the IAEA Ministerial Conference on Nuclear Safety" [2] published by Nuclear Emergency Response Headquarters in June 2011, three months after the earthquake.Up to 2012 summer, the major investigation boards, including the Japanese Diet, the Japanese Cabinet and TEPCO, published their final reports, in which detailed causes of this accident and several recommendations are assessed from each perspective.In this paper, the authors examine to introduce the lessons learned to be applied to the space safety as findings from these reports.

  17. U.S. Civil Rotorcraft Accidents, 1963 Through 1997

    NASA Technical Reports Server (NTRS)

    Harris, Franklin D.; Kasper, Eugene F.; Iseler, Laura E.

    2000-01-01

    Narrative summary data produced by the U.S. National Transportation Safety Board (NTSB) has been obtained and analyzed for all 8,436 U.S. civil registered rotorcraft accidents which occurred from mid-1963 through 1997. This analysis was based on the NTSB's assignment of each mishap into one of 21 "first event" categories. The number of U.S. civil registered rotorcraft as recorded by the Federal Aviation Administration (FAA) for the same period has also been obtained. Taken together, these data indicate the civil rotorcraft accident rate (on a per 1,000 registered rotorcraft basis) has decreased by almost a factor of 10 (i.e., from 130 accidents per 1,000 rotorcraft in 1964 to 13.4 per 1,000 in 1997). Analysis of the mishap data indicates over 70% of the rotorcraft accidents were associated with one of the following four NTSB "first event" categories: 2408 Loss of engine power (28.5%); 1,322 In-flight collisions with objects (15.7%); 1,114 Loss of control (13.2%); 1,083 Airframe/component/system failure or malfunction (12.8%).

  18. Safety analysis report for the Galileo Mission. Volume 3, book 2: Nuclear risk analysis document. Appendices, revision 1

    NASA Astrophysics Data System (ADS)

    1989-01-01

    It is the purpose of the NRAD to provide an analysis of the range of potential consequences of accidents which have been identified that are associated with the launching and deployment of the Galileo mission spacecraft. The specific consequences analyzed are those associated with the possible release of radioactive material (fuel) of the Radioisotope Thermoelectric Generators (RTGs). They are in terms of radiation doses to people and areas of deposition of radioactive material. These consequence analyses can be used in several ways. One way is to identify the potential range of consequences which might have to be dealt with if there were to be an accident with a release of fuel, so as to assure that, given such an accident, the health and safety of the public will be reasonably protected. Another use of the information, in conjunction with accident and release probabilities, is to estimate the risks associated with the mission. That is, most space launches occur without incident. Given an accident, the most probable result relative to the RTGs is complete containment of the radioactive material. Only a small fraction of accidents might result in a release of fuel and subsequent radiological consequences. The combination of probability with consequence is risk, which can be compared to other human and societal risks to assure that no undue risks are implied by undertaking the mission. Book 2 contains eight appendices.

  19. Causes of Coal Mine Accidents in the World and Turkey.

    PubMed

    Küçük, Filiz Çağla Uyanusta; Ilgaz, Aslıhan

    2015-04-01

    Occupational accidents and occupational diseases are common in the mining sector in Turkey and throughout the world. The most common causes of accidents in coal mining are firedamp and dust explosions, landslips, mine fires, and technical failures related to transport and mechanization. An analysis of occupational accidents in the consideration of social and economic factors will let understand the real causes behind these accidents, which are said to happen inevitably due to technical deficiencies or failures. Irregular working conditions, based on profit maximization and cost minimization, are related to strategic operational preferences and public policies. Proving that accidents in mines, where occupational health and safety measures are not implemented and inspections are not done properly or at all, are caused by the fact that production is imposed to be carried out in the fastest, cheapest, and most profitable way will allow us to take steps to prevent further mine accidents.

  20. Effectiveness of Direct Safety Regulations on Manufacturers and Users of Industrial Machines: Its Implications on Industrial Safety Policies in Republic of Korea.

    PubMed

    Choi, Gi Heung

    2017-03-01

    Despite considerable efforts made in recent years, the industrial accident rate and the fatality rate in the Republic of Korea are much higher than those in most developed countries in Europe and North America. Industrial safety policies and safety regulations are also known to be ineffective and inefficient in some cases. This study focuses on the quantitative evaluation of the effectiveness of direct safety regulations such as safety certification, self-declaration of conformity, and safety inspection of industrial machines in the Republic of Korea. Implications on safety policies to restructure the industrial safety system associated with industrial machines are also explored. Analysis of causes in industrial accidents associated with industrial machines confirms that technical causes need to be resolved to reduce both the frequency and the severity of such industrial accidents. Statistical analysis also confirms that the indirect effects of safety device regulation on users are limited for a variety of reasons. Safety device regulation needs to be shifted to complement safety certification and self-declaration of conformity for more balanced direct regulations on manufacturers and users. An example of cost-benefit analysis on conveyor justifies such a transition. Industrial safety policies and regulations associated with industrial machines must be directed towards eliminating the sources of danger at the stage of danger creation, thereby securing the safe industrial machines. Safety inspection further secures the safety of workers at the stage of danger use. The overall balance between such safety regulations is achieved by proper distribution of industrial machines subject to such regulations and the intensity of each regulation. Rearrangement of industrial machines subject to safety certification and self-declaration of conformity to include more movable industrial machines and other industrial machines with a high level of danger is also suggested.

  1. The effects of aircraft certification rules on general aviation accidents

    NASA Astrophysics Data System (ADS)

    Anderson, Carolina Lenz

    The purpose of this study was to analyze the frequency of general aviation airplane accidents and accident rates on the basis of aircraft certification to determine whether or not differences in aircraft certification rules had an influence on accidents. In addition, the narrative cause descriptions contained within the accident reports were analyzed to determine whether there were differences in the qualitative data for the different certification categories. The certification categories examined were: Federal Aviation Regulations Part 23, Civil Air Regulations 3, Light Sport Aircraft, and Experimental-Amateur Built. The accident causes examined were those classified as: Loss of Control, Controlled Flight into Terrain, Engine Failure, and Structural Failure. Airworthiness certification categories represent a wide diversity of government oversight. Part 23 rules have evolved from the initial set of simpler design standards and have progressed into a comprehensive and strict set of rules to address the safety issues of the more complex airplanes within the category. Experimental-Amateur Built airplanes have the least amount of government oversight and are the fastest growing segment. The Light Sport Aircraft category is a more recent certification category that utilizes consensus standards in the approval process. Civil Air Regulations 3 airplanes were designed and manufactured under simpler rules but modifying these airplanes has become lengthy and expensive. The study was conducted using a mixed methods methodology which involves both quantitative and qualitative elements. A Chi-Square test was used for a quantitative analysis of the accident frequency among aircraft certification categories. Accident rate analysis of the accidents among aircraft certification categories involved an ANCOVA test. The qualitative component involved the use of text mining techniques for the analysis of the narrative cause descriptions contained within the accident reports. The Chi

  2. NASA's Accident Precursor Analysis Process and the International Space Station

    NASA Technical Reports Server (NTRS)

    Groen, Frank; Lutomski, Michael

    2010-01-01

    This viewgraph presentation reviews the implementation of Accident Precursor Analysis (APA), as well as the evaluation of In-Flight Investigations (IFI) and Problem Reporting and Corrective Action (PRACA) data for the identification of unrecognized accident potentials on the International Space Station.

  3. Major Accidents (Gray Swans) Likelihood Modeling Using Accident Precursors and Approximate Reasoning.

    PubMed

    Khakzad, Nima; Khan, Faisal; Amyotte, Paul

    2015-07-01

    Compared to the remarkable progress in risk analysis of normal accidents, the risk analysis of major accidents has not been so well-established, partly due to the complexity of such accidents and partly due to low probabilities involved. The issue of low probabilities normally arises from the scarcity of major accidents' relevant data since such accidents are few and far between. In this work, knowing that major accidents are frequently preceded by accident precursors, a novel precursor-based methodology has been developed for likelihood modeling of major accidents in critical infrastructures based on a unique combination of accident precursor data, information theory, and approximate reasoning. For this purpose, we have introduced an innovative application of information analysis to identify the most informative near accident of a major accident. The observed data of the near accident were then used to establish predictive scenarios to foresee the occurrence of the major accident. We verified the methodology using offshore blowouts in the Gulf of Mexico, and then demonstrated its application to dam breaches in the United Sates. © 2015 Society for Risk Analysis.

  4. Computer & manual accident typing for bicyclist accidents : administrator's guide

    DOT National Transportation Integrated Search

    1983-01-01

    This guide provides guidelines and procedures for classifying and analyzing bicyclist-motor vehicle accidents. The approach described herein is part of a systematic effort by the National Highway Traffic Safety Administration (NHTSA) to assist states...

  5. An Evidential Reasoning-Based CREAM to Human Reliability Analysis in Maritime Accident Process.

    PubMed

    Wu, Bing; Yan, Xinping; Wang, Yang; Soares, C Guedes

    2017-10-01

    This article proposes a modified cognitive reliability and error analysis method (CREAM) for estimating the human error probability in the maritime accident process on the basis of an evidential reasoning approach. This modified CREAM is developed to precisely quantify the linguistic variables of the common performance conditions and to overcome the problem of ignoring the uncertainty caused by incomplete information in the existing CREAM models. Moreover, this article views maritime accident development from the sequential perspective, where a scenario- and barrier-based framework is proposed to describe the maritime accident process. This evidential reasoning-based CREAM approach together with the proposed accident development framework are applied to human reliability analysis of a ship capsizing accident. It will facilitate subjective human reliability analysis in different engineering systems where uncertainty exists in practice. © 2017 Society for Risk Analysis.

  6. What can the drivers' own description from combined sources provide in an analysis of driver distraction and low vigilance in accident situations?

    PubMed

    Tivesten, Emma; Wiberg, Henrik

    2013-03-01

    Accident data play an important role in vehicle safety development. Accident data sources are generally limited in terms of how much information is provided on driver states and behaviour prior to an accident. However, the precise limitations vary between databases, due to differences in analysis focus and data collection procedures between organisations. If information about a specific accident can be retrieved from more than one data source it should be possible to combine the available information sets to facilitate data from one source to compensate for limitations in the other(s). To investigate the viability of such compensation, this study identified a set of accidents recorded in two different data sources. The first data source investigated was an accident mail survey and the second data source insurance claims documents consisting predominantly of insurance claims completed by the involved road users. An analysis of survey variables was compared to a case analysis including word data derived from the same survey and filed insurance claims documents. For each accident, the added value of having access to more than one source of information was assessed. To limit the scope of this study, three particular topics were investigated: available information on low vigilance (e.g., being drowsy, ill); secondary task distraction (e.g., talking with passengers, mobile phone use); and distraction related to the driving task (e.g., looking for approaching vehicles). Results suggest that for low vigilance and secondary task distraction, a combination of the mail survey and insurance claims documents provide more reliable and detailed pre-crash information than survey variables alone. However, driving related distraction appears to be more difficult to capture. In order to gain a better understanding of the above issues and how frequently they occur in accidents, the data sources and analysis methods suggested here may be combined with other investigation methods such

  7. Truck accidents at freeway ramps : data analysis and high-risk site identification

    DOT National Transportation Integrated Search

    1998-01-01

    To examine the relationship of ramp design to truck accident rates, this paper presents an analysis of truck accidents in Washington State, plus a comparison to limited data from Colorado and California. The authors group freeway truck accidents by r...

  8. Jerky driving--An indicator of accident proneness?

    PubMed

    Bagdadi, Omar; Várhelyi, András

    2011-07-01

    This study uses continuously logged driving data from 166 private cars to derive the level of jerks caused by the drivers during everyday driving. The number of critical jerks found in the data is analysed and compared with the self-reported accident involvement of the drivers. The results show that the expected number of accidents for a driver increases with the number of critical jerks caused by the driver. Jerk analyses make it possible to identify safety critical driving behaviour or "accident prone" drivers. They also facilitate the development of safety measures such as active safety systems or advanced driver assistance systems, ADAS, which could be adapted for specific groups of drivers or specific risky driving behaviour. Copyright © 2011 Elsevier Ltd. All rights reserved.

  9. Workflow interruptions, cognitive failure and near-accidents in health care.

    PubMed

    Elfering, Achim; Grebner, Simone; Ebener, Corinne

    2015-01-01

    Errors are frequent in health care. A specific model was tested that affirms failure in cognitive action regulation to mediate the influence of nurses' workflow interruptions and safety conscientiousness on near-accidents in health care. One hundred and sixty-five nurses from seven Swiss hospitals participated in a questionnaire survey. Structural equation modelling confirmed the hypothesised mediation model. Cognitive failure in action regulation significantly mediated the influence of workflow interruptions on near-accidents (p < .05). An indirect path from conscientiousness to near-accidents via cognitive failure in action regulation was also significant (p < .05). Compliance with safety regulations was significantly related to cognitive failure and near-accidents; moreover, cognitive failure mediated the association between compliance and near-accidents (p < .05). Contrary to expectations, compliance with safety regulations was not related to workflow interruptions. Workflow interruptions caused by colleagues, patients and organisational constraints are likely to trigger errors in nursing. Work redesign is recommended to reduce cognitive failure and improve safety of nurses and patients.

  10. Decrease of morbidity in road traffic accidents in a high income country - an analysis of 24,405 accidents in a 21 year period.

    PubMed

    Ernstberger, Antonio; Joeris, Alexander; Daigl, Monica; Kiss, Miklos; Angerpointner, Katharina; Nerlich, Michael; Schmucker, Uli

    2015-10-01

    The WHO initiated the "Decade of Action for Road Safety" because the fatality on road traffic accidents could become the fifth leading cause of death in 2030. On the contrary, fatalities continue to decrease in high income countries. The aim of the study was to find evidence for changes in injury severity of passenger car occupants after road traffic accidents in Germany over time, and to find contributing factors. Data from the German In Depth Accident Study (GIDAS), representative for Germany, was used. A total of 24.405 accidents, reported from 1991 until 2011. 44.503 adult passenger car occupants were examined. A multivariable logistic regression model was developed to find reasons for observed trends over time. The relative decrease in mortality was 68.8% from 1991 until 2011. Between 2006 and 2011, the percentage of severely injured traffic victims was less than half, both in terms of the whole body and individual body regions. For injuries with an Abbreviated Injury Scale (AIS) ≥ 2, the percentage of persons with lower leg injuries declined by 72.5%, followed by the percentage of persons with pelvic injuries (61.5%), upper extremity injuries (57.7%), head injuries (54.3%), thorax injuries (50.0%), and abdomen injuries (40.0%). The multivariable regression model found 13 independent variables associated with injury prevention (e.g. seat belt use: OR 0.41, CI 95% 0.32-0.49; airbag: OR 0.86, CI 95% 0.75-0.99). The implementation of protective factors increased over time while accident constellations with a high probability for severe injury decreased over time. The decrease of severe injuries after road traffic accidents can be only attributed to a comprehensive approach including the enforcement of road safety policies and innovations in car engineering and emergency medicine. Traffic related measures and alcohol level control, and seat belt usage enforcement next to other technical advances are considered especially important. Copyright © 2015 Elsevier Ltd

  11. GIS based analysis of Intercity Fatal Road Traffic Accidents in Iran

    PubMed Central

    Alizadeh, A; Zare, M; Darparesh, M; Mohseni, S; Soleimani-Ahmadi, M

    2015-01-01

    car accidents, which were in their nature preventable, the key players in road safety including governments, car manufacturers, and road developers were recommended to use GIS based accident data for a more efficient planning and budgeting towards the intercity car accidents reduction. PMID:28255402

  12. GIS based analysis of Intercity Fatal Road Traffic Accidents in Iran.

    PubMed

    Alizadeh, A; Zare, M; Darparesh, M; Mohseni, S; Soleimani-Ahmadi, M

    2015-01-01

    accidents, which were in their nature preventable, the key players in road safety including governments, car manufacturers, and road developers were recommended to use GIS based accident data for a more efficient planning and budgeting towards the intercity car accidents reduction.

  13. [Mechanism of pelvic girdle injuries in street traffic. Medical-technical accident analysis].

    PubMed

    Pohlemann, T; Richter, M; Otte, D; Gänsslen, A; Bartram, H; Tscherne, H

    2000-04-01

    During 1985 and 1993, 7,410 persons were injured in traffic accidents in the area of Hanover. Of these, 306 (4.1%) sustained a pelvic girdle injury. In 139 cases (45%), the pelvic girdle injuries were further classified (Pennal and Tile) and a technical reconstruction of the accident situation was performed. 52% were type A, 27% type B and 21% type C injuries. Some 47% of the casualties were vehicle occupants, 31% pedestrians, 12% motorcyclists and 10% cyclists. In restrained vehicle occupants pelvic girdle injuries occurred mostly in accidents with a delta-v of more than 30 km/h, whereas in unrestrained vehicle occupants, pedestrians and cyclists they also occurred with lower delta-v or collision speed. The percentage of type B and C injuries increased with higher velocities. In addition to further improvements in passive safety, lower collision speed or delta-v is necessary to reduce or prevent pelvic girdle injuries. The reconstruction of pelvic girdle injury mechanism in traffic accidents is possible, when both technical and medical parameters are considered.

  14. Analysis of Occupational Accident Fatalities and Injuries Among Male Group in Iran Between 2008 and 2012

    PubMed Central

    Alizadeh, Seyed Shamseddin; Mortazavi, Seyed Bagher; Sepehri, Mohammad Mehdi

    2015-01-01

    Background: Because of occupational accidents, permanent disabilities and deaths occur and economic and workday losses emerge. Objectives: The purpose of the present study was to investigate the factors responsible for occupational accidents occurred in Iran. Patients and Methods: The current study analyzed 1464 occupational accidents recorded by the Ministry of Labor and Social Affairs’ offices in Iran during 2008 - 2012. At first, general understanding of accidents was obtained using descriptive statistics. Afterwards, the chi-square test and Cramer’s V statistic (Vc) were used to determine the association between factors influencing the type of injury as occupational accident outcomes. Results: There was no significant association between marital status and time of day with the type of injury. However, activity sector, cause of accident, victim’s education, age of victim and victim’s experience were significantly associated with the type of injury. Conclusions: Successful accident prevention relies largely on knowledge about the causes of accidents. In any accident control activity, particularly in occupational accidents, correctly identifying high-risk groups and factors influencing accidents is the key to successful interventions. Results of this study can cause to increase accident awareness and enable workplace’s management to select and prioritize problem areas and safety system weakness in workplaces. PMID:26568848

  15. Railroad safety program, task 2

    NASA Technical Reports Server (NTRS)

    1983-01-01

    Aspects of railroad safety and the preparation of a National Inspection Plan (NIP) for rail safety improvement are examined. Methodology for the allocation of inspection resources, preparation of a NIP instruction manual, and recommendations for future NIP, are described. A statistical analysis of regional rail accidents is presented with causes and suggested preventive measures included.

  16. Analysis of fatal accidents with tractors in the Centre of Portugal: Ten years analysis.

    PubMed

    Antunes, Soraia M; Cordeiro, Cristina; Teixeira, Helena M

    2018-06-01

    Tractors have been described as one of the deadliest farming implements concerning agricultural activity. In Portugal, the scientific investigations about this problem are practically non-existent, with only statistical studies performed by entities related to road traffic safety, not in accordance to the study now performed, pinpointing the possibility of an underreporting of these accidents. This work aims to characterize the fatal tractor accidents in Portugal, autopsied at the Forensic Pathology Department of the Centre Branch of the National Institute of Legal Medicine and Forensic Sciences of Portugal, analysing several variables: gender, age, occupation, survival time, the victim position in the tractor, cause of death, toxicological and histological exams, year/month/day of the week, type of agricultural machine, existence of rollover protective structures (ROPS), type of accident, ground conditions, circumstantial information and geographic distribution of the accidents. All the autopsies between 2005 and 2014 were analysed. The victim profile corresponded to a man (89.5%), between 61 and 70 years old (33.3%), retired (43.9%), being the tractor driver (45.6%). In most of the cases, death occurred in less than 24h after the accident. These fatalities arose mainly in May and October. Rollover in sloping land was the most common type of accident, and cranioencephalic, thoracic and abdominal traumatic injuries were the main cause of death. In 16.2% of the cases, blood alcohol concentration was above the lower limit established in our road traffic law (<0.5g/L). There was lack information about the use of ROPS (95.9%), and even when existent, the protections were not used or were incorrectly used. This is the first national study involving the description of the forensic achievements in each autopsy related to tractor accidents, and the corresponding circumstances that contributed to the death. Many barriers remain about this matter, but the Portuguese

  17. Severe Accident Sequence Analysis Program: Anticipated transient without scram simulations for Browns Ferry Nuclear Plant Unit 1

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Dallman, R J; Gottula, R C; Holcomb, E E

    1987-05-01

    An analysis of five anticipated transients without scram (ATWS) was conducted at the Idaho National Engineering Laboratory (INEL). The five detailed deterministic simulations of postulated ATWS sequences were initiated from a main steamline isolation valve (MSIV) closure. The subject of the analysis was the Browns Ferry Nuclear Plant Unit 1, a boiling water reactor (BWR) of the BWR/4 product line with a Mark I containment. The simulations yielded insights to the possible consequences resulting from a MSIV closure ATWS. An evaluation of the effects of plant safety systems and operator actions on accident progression and mitigation is presented.

  18. Examining accident reports involving autonomous vehicles in California.

    PubMed

    Favarò, Francesca M; Nader, Nazanin; Eurich, Sky O; Tripp, Michelle; Varadaraju, Naresh

    2017-01-01

    Autonomous Vehicle technology is quickly expanding its market and has found in Silicon Valley, California, a strong foothold for preliminary testing on public roads. In an effort to promote safety and transparency to consumers, the California Department of Motor Vehicles has mandated that reports of accidents involving autonomous vehicles be drafted and made available to the public. The present work shows an in-depth analysis of the accident reports filed by different manufacturers that are testing autonomous vehicles in California (testing data from September 2014 to March 2017). The data provides important information on autonomous vehicles accidents' dynamics, related to the most frequent types of collisions and impacts, accident frequencies, and other contributing factors. The study also explores important implications related to future testing and validation of semi-autonomous vehicles, tracing the investigation back to current literature as well as to the current regulatory panorama.

  19. Sleepiness and sleep-disordered breathing in truck drivers : risk analysis of road accidents.

    PubMed

    Catarino, Rosa; Spratley, Jorge; Catarino, Isabel; Lunet, Nuno; Pais-Clemente, Manuel

    2014-03-01

    Portugal has one of the highest road traffic fatality rates in Europe. A clear association between sleep-disordered breathing (SDB) and traffic accidents has been previously demonstrated. This study aimed to determine prevalence of excessive daytime sleepiness (EDS) and other sleep disorder symptoms among truck drivers and to identify which individual traits and work habits are associated to increased sleepiness and accident risk. We evaluated a sample of 714 truck drivers using a questionnaire (244 face-to-face interviews, 470 self-administered) that included sociodemographic data, personal habits, previous accidents, Epworth Sleepiness Scale (ESS), and the Berlin questionnaire (BQ). Twenty percent of drivers had EDS and 29 % were at high risk for having obstructive sleep apnea syndrome (OSAS). Two hundred sixty-one drivers (36.6 %) reported near-miss accidents (42.5 % sleep related) and 264 (37.0 %), a driving accident (16.3 % sleep related). ESS score ≥ 11 was a risk factor for both near-miss accidents (odds ratio (OR)=3.84, p<0.01) and accidents (OR=2.25, p<0.01). Antidepressant use was related to accidents (OR=3.30, p=0.03). We found an association between high Mallampati score (III-IV) and near misses (OR=1.89, p=0.04). In this sample of Portuguese truck drivers, we observed a high prevalence of EDS and other sleep disorder symptoms. Accident risk was related to sleepiness and antidepressant use. Identifying drivers at risk for OSAS should be a major priority of medical assessment centers, as a public safety policy.

  20. Accident/incident bulletin : calendar year 1995

    DOT National Transportation Integrated Search

    1996-08-01

    Railroads must file monthly accident/incident reports with the Federal Railroad Administrations (FRA) Office of Safety. Bulletin 164 is a summary of accident/incident data reported by 679 railroads for calendar year 1995. The FRA Guide for Prepari...

  1. Accident/incident bulletin : calendar year 1996

    DOT National Transportation Integrated Search

    1997-08-01

    Railroads must file monthly accident/incident reports with the Federal Railroad Administrations (FRA) Office of Safety. Bulletin 165 is a summary of accident/incident data reported by 704 railroads for calendar year 1996. There are three basic cat...

  2. Insights Gained from Forensic Analysis with MELCOR of the Fukushima-Daiichi Accidents.

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Andrews, Nathan C.; Gauntt, Randall O.

    Since the accidents at Fukushima-Daiichi, Sandia National Laboratories has been modeling these accident scenarios using the severe accident analysis code, MELCOR. MELCOR is a widely used computer code developed at Sandia National Laboratories since ~1982 for the U.S. Nuclear Regulatory Commission. Insights from the modeling of these accidents is being used to better inform future code development and potentially improved accident management. To date, our necessity to better capture in-vessel thermal-hydraulic and ex-vessel melt coolability and concrete interactions has led to the implementation of new models. The most recent analyses, presented in this paper, have been in support of themore » of the Organization for Economic Cooperation and Development Nuclear Energy Agency’s (OECD/NEA) Benchmark Study of the Accident at the Fukushima Daiichi Nuclear Power Station (BSAF) Project. The goal of this project is to accurately capture the source term from all three releases and then model the atmospheric dispersion. In order to do this, a forensic approach is being used in which available plant data and release timings is being used to inform the modeled MELCOR accident scenario. For example, containment failures, core slumping events and lower head failure timings are all enforced parameters in these analyses. This approach is fundamentally different from a blind code assessment analysis often used in standard problem exercises. The timings of these events are informed by representative spikes or decreases in plant data. The combination of improvements to the MELCOR source code resulting from analysis previous accident analysis and this forensic approach has allowed Sandia to generate representative and plausible source terms for all three accidents at Fukushima Daiichi out to three weeks after the accident to capture both early and late releases. In particular, using the source terms developed by MELCOR, the MACCS software code, which models atmospheric dispersion

  3. Key factors contributing to accident severity rate in construction industry in Iran: a regression modelling approach.

    PubMed

    Soltanzadeh, Ahmad; Mohammadfam, Iraj; Moghimbeigi, Abbas; Ghiasvand, Reza

    2016-03-01

    Construction industry involves the highest risk of occupational accidents and bodily injuries, which range from mild to very severe. The aim of this cross-sectional study was to identify the factors associated with accident severity rate (ASR) in the largest Iranian construction companies based on data about 500 occupational accidents recorded from 2009 to 2013. We also gathered data on safety and health risk management and training systems. Data were analysed using Pearson's chi-squared coefficient and multiple regression analysis. Median ASR (and the interquartile range) was 107.50 (57.24- 381.25). Fourteen of the 24 studied factors stood out as most affecting construction accident severity (p<0.05). These findings can be applied in the design and implementation of a comprehensive safety and health risk management system to reduce ASR.

  4. Issues and challenges for pedestrian active safety systems based on real world accidents.

    PubMed

    Hamdane, Hédi; Serre, Thierry; Masson, Catherine; Anderson, Robert

    2015-09-01

    The purpose of this study was to analyze real crashes involving pedestrians in order to evaluate the potential effectiveness of autonomous emergency braking systems (AEB) in pedestrian protection. A sample of 100 real accident cases were reconstructed providing a comprehensive set of data describing the interaction between the vehicle, the environment and the pedestrian all along the scenario of the accident. A generic AEB system based on a camera sensor for pedestrian detection was modeled in order to identify the functionality of its different attributes in the timeline of each crash scenario. These attributes were assessed to determine their impact on pedestrian safety. The influence of the detection and the activation of the AEB system were explored by varying the field of view (FOV) of the sensor and the level of deceleration. A FOV of 35° was estimated to be required to detect and react to the majority of crash scenarios. For the reaction of a system (from hazard detection to triggering the brakes), between 0.5 and 1s appears necessary. Copyright © 2015 Elsevier Ltd. All rights reserved.

  5. Causes of Coal Mine Accidents in the World and Turkey

    PubMed Central

    Küçük, Filiz Çağla Uyanusta; Ilgaz, Aslıhan

    2015-01-01

    Occupational accidents and occupational diseases are common in the mining sector in Turkey and throughout the world. The most common causes of accidents in coal mining are firedamp and dust explosions, landslips, mine fires, and technical failures related to transport and mechanization. An analysis of occupational accidents in the consideration of social and economic factors will let understand the real causes behind these accidents, which are said to happen inevitably due to technical deficiencies or failures. Irregular working conditions, based on profit maximization and cost minimization, are related to strategic operational preferences and public policies. Proving that accidents in mines, where occupational health and safety measures are not implemented and inspections are not done properly or at all, are caused by the fact that production is imposed to be carried out in the fastest, cheapest, and most profitable way will allow us to take steps to prevent further mine accidents. PMID:29404108

  6. On statistical inference in time series analysis of the evolution of road safety.

    PubMed

    Commandeur, Jacques J F; Bijleveld, Frits D; Bergel-Hayat, Ruth; Antoniou, Constantinos; Yannis, George; Papadimitriou, Eleonora

    2013-11-01

    Data collected for building a road safety observatory usually include observations made sequentially through time. Examples of such data, called time series data, include annual (or monthly) number of road traffic accidents, traffic fatalities or vehicle kilometers driven in a country, as well as the corresponding values of safety performance indicators (e.g., data on speeding, seat belt use, alcohol use, etc.). Some commonly used statistical techniques imply assumptions that are often violated by the special properties of time series data, namely serial dependency among disturbances associated with the observations. The first objective of this paper is to demonstrate the impact of such violations to the applicability of standard methods of statistical inference, which leads to an under or overestimation of the standard error and consequently may produce erroneous inferences. Moreover, having established the adverse consequences of ignoring serial dependency issues, the paper aims to describe rigorous statistical techniques used to overcome them. In particular, appropriate time series analysis techniques of varying complexity are employed to describe the development over time, relating the accident-occurrences to explanatory factors such as exposure measures or safety performance indicators, and forecasting the development into the near future. Traditional regression models (whether they are linear, generalized linear or nonlinear) are shown not to naturally capture the inherent dependencies in time series data. Dedicated time series analysis techniques, such as the ARMA-type and DRAG approaches are discussed next, followed by structural time series models, which are a subclass of state space methods. The paper concludes with general recommendations and practice guidelines for the use of time series models in road safety research. Copyright © 2012 Elsevier Ltd. All rights reserved.

  7. An aftermath analysis of the 2014 coal mine accident in Soma, Turkey: Use of risk performance indicators based on historical experience.

    PubMed

    Spada, Matteo; Burgherr, Peter

    2016-02-01

    On the 13th of May 2014 a fire related incident in the Soma coal mine in Turkey caused 301 fatalities and more than 80 injuries. This has been the largest coal mine accident in Turkey, and in the OECD country group, so far. This study investigated if such a disastrous event should be expected, in a statistical sense, based on historical observations. For this purpose, PSI's ENSAD database is used to extract accident data for the period 1970-2014. Four different cases are analyzed, i.e., OECD, OECD w/o Turkey, Turkey and USA. Analysis of temporal trends for annual numbers of accidents and fatalities indicated a non-significant decreasing tendency for OECD and OECD w/o Turkey and a significant one for USA, whereas for Turkey both measures showed an increase over time. The expectation analysis revealed clearly that an event with the consequences of the Soma accident is rather unlikely for OECD, OECD w/o Turkey and USA. In contrast, such a severe accident has a substantially higher expectation for Turkey, i.e. it cannot be considered an extremely rare event, based on historical experience. This indicates a need for improved safety measures and stricter regulations in the Turkish coal mining sector in order to get closer to the rest of OECD. Copyright © 2015 Elsevier Ltd. All rights reserved.

  8. Urban transport safety assessment in akure based on corresponding performance indicators

    NASA Astrophysics Data System (ADS)

    Oye, Adedamola; Aderinlewo, Olufikayo; Croope, Silvana

    2013-03-01

    The level of safety of the transportation system in Akure, Nigeria was assessed by identifying the associated road safety problems and developing the corresponding safety performance indicators. These indicators were analysed with respect to accidents that occurred within the city from the year 2005 to 2009 based on the corresponding attributable risk measures. The results of the analysis showed the state of existing safety programs in Akure town. Six safety performance indicators were identified namely alcohol and drug use, excessive speeds, protection system (use of seat belts and helmets), use of day time running lights, state of vehicles (passive safety) and road condition. These indicators were used to determine the percentage of injury accidents as follows: 83.33% and 86.36% for years 2005 and 2006 respectively, 81.46% for year 2007 while years 2008 and 2009 had 82.86% and 78.12% injury accidents respectively.

  9. Formulating accident occurrence as a survival process.

    PubMed

    Chang, H L; Jovanis, P P

    1990-10-01

    A conceptual framework for accident occurrence is developed based on the principle of the driver as an information processor. The framework underlies the development of a modeling approach that is consistent with the definition of exposure to risk as a repeated trial. Survival theory is proposed as a statistical technique that is consistent with the conceptual structure and allows the exploration of a wide range of factors that contribute to highway operating risk. This survival model of accident occurrence is developed at a disaggregate level, allowing safety researchers to broaden the scope of studies which may be limited by the use of traditional aggregate approaches. An application of the approach to motor carrier safety is discussed as are potential applications to a variety of transportation industries. Lastly, a typology of highway safety research methodologies is developed to compare the properties of four safety methodologies: laboratory experiments, on-the-road studies, multidisciplinary accident investigations, and correlational studies. The survival theory formulation has a mathematical structure that is compatible with each safety methodology, so it may facilitate the integration of findings across methodologies.

  10. The role of OSHA violations in serious workplace accidents.

    PubMed

    Mendeloff, J

    1984-05-01

    California accident investigations for 1976 show that violations of the Occupational Safety and Health Administration's safety standards were a contributing factor in 13% to 19% of the 645 deaths reported to the workers' compensation program during that year. However, a panel of safety engineers judged that only about 50% of these violations could have been detected if an inspector had visited the day before the accident. These findings indicate that the potential gains from stronger enforcement of current standards are limited but not insignificant. The likelihood that a violation contributed to a serious accident varied considerably among accident types, industries, and size classes of plants. These findings can be used to increase the efficiency and effectiveness of the OSHA program by means of better targeting of inspections and accident investigations, more intelligent assessment of which violations should be penalized most heavily, and the provision of information to employers and workers about which violations are most consequential.

  11. Inroads into Equestrian Safety: Rider-Reported Factors Contributing to Horse-Related Accidents and Near Misses on Australian Roads.

    PubMed

    Thompson, Kirrilly; Matthews, Chelsea

    2015-07-22

    Horse riding and horse-related interactions are inherently dangerous. When they occur on public roads, the risk profile of equestrian activities is complicated by interactions with other road users. Research has identified speed, proximity, visibility, conspicuity and mutual misunderstanding as factors contributing to accidents and near misses. However, little is known about their significance or incidence in Australia. To explore road safety issues amongst Australian equestrians, we conducted an online survey. More than half of all riders (52%) reported having experienced at least one accident or near miss in the 12 months prior to the survey. Whilst our findings confirm the factors identified overseas, we also identified issues around rider misunderstanding of road rules and driver misunderstanding of rider hand signals. Of particular concern, we also found reports of potentially dangerous rider-directed road rage. We identify several areas for potential safety intervention including (1) identifying equestrians as vulnerable road users and horses as sentient decision-making vehicles (2) harmonising laws regarding passing horses, (3) mandating personal protective equipment, (4) improving road signage, (5) comprehensive data collection, (6) developing mutual understanding amongst road-users, (7) safer road design and alternative riding spaces; and (8) increasing investment in horse-related safety initiatives.

  12. Lift truck safety review

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Cadwallader, L.C.

    1997-03-01

    This report presents safety information about powered industrial trucks. The basic lift truck, the counterbalanced sit down rider truck, is the primary focus of the report. Lift truck engineering is briefly described, then a hazard analysis is performed on the lift truck. Case histories and accident statistics are also given. Rules and regulations about lift trucks, such as the US Occupational Safety an Health Administration laws and the Underwriter`s Laboratories standards, are discussed. Safety issues with lift trucks are reviewed, and lift truck safety and reliability are discussed. Some quantitative reliability values are given.

  13. Review of hydrogen accidents and incidents in NASA operations

    NASA Technical Reports Server (NTRS)

    Ordin, P. M.

    1974-01-01

    A number of the accidents/incidents with hydrogen in NASA operations are reviewed. The cause factors for the mishaps are reviewed and show that although few accidents occurred, the number could have been further reduced if the established NASA rules and regulations had been followed. Requirements for effective safety codes and areas of study for hydrogen safety information are included. The report concludes with a compilation of 96 hydrogen mishaps; a description of the accidents and their causes.

  14. Farm Safety

    PubMed Central

    Wilson, G. S.

    1966-01-01

    Accident and safety are related terms; the higher the accident rate in any industry, the greater is the need for safety measures designed to prevent accidents. This article discusses the accident and safety problems in agriculture, which includes horticulture and forestry. There is still a tendency among townspeople to think of the countryside as peaceful and tranquil, a place where nothing happens very quickly and far removed from violent death or crippling injury. This pleasant rustic picture has undergone a striking change in the last 30 years owing to considerable agricultural mechanization and the development of chemical pesticides, which have brought new dangers to those who live and work on the land. Although men have readily adapted themselves to new machines and methods, they have not proved as able to recognize new dangers and learn how to guard against them. In consequence, accidents have increased to such an extent that the whole industry has realized the need for positive preventive measures. In this country, it is generally accepted that an employer of labour has a responsibility to provide safe working conditions for those he employs. Farm safety legislation goes a little further and usually requires an employer to provide necessary safeguards, with the added requirement on a worker to make use of them. It is a feature of accident prevention work that it never reaches a stage when it can be regarded as complete. Even when a reduction in accidents has been achieved, the effort must be sustained or the trend will be quickly reversed. Images PMID:5904095

  15. Usage and effectiveness of seat and shoulder belts in rural Pennsylvania accidents

    DOT National Transportation Integrated Search

    1974-12-01

    This report presents an analysis of lap-belt and shoulder- belt usage and effectiveness in rural Pennsylvania accidents. The data were collected by the Pennsylvania State Police under an agreement with the National Highway Traffic Safety Administrati...

  16. Road accidents and business cycles in Spain.

    PubMed

    Rodríguez-López, Jesús; Marrero, Gustavo A; González, Rosa Marina; Leal-Linares, Teresa

    2016-11-01

    This paper explores the causes behind the downturn in road accidents in Spain across the last decade. Possible causes are grouped into three categories: Institutional factors (a Penalty Point System, PPS, dating from 2006), technological factors (active safety and passive safety of vehicles), and macroeconomic factors (the Great recession starting in 2008, and an increase in fuel prices during the spring of 2008). The PPS has been blessed by incumbent authorities as responsible for the decline of road fatalities in Spain. Using cointegration techniques, the GDP growth rate, the fuel price, the PPS, and technological items embedded in motor vehicles appear to be statistically significantly related with accidents. Importantly, PPS is found to be significant in reducing fatal accidents. However, PPS is not significant for non-fatal accidents. In view of these results, we conclude that road accidents in Spain are very sensitive to the business cycle, and that the PPS influenced the severity (fatality) rather than the quantity of accidents in Spain. Importantly, technological items help explain a sizable fraction in accidents downturn, their effects dating back from the end of the nineties. Copyright © 2016 Elsevier Ltd. All rights reserved.

  17. Evaluation of Safety Programs with Respect to the Causes of General Aviation Accidents. Volume I. Technical Report,

    DTIC Science & Technology

    1980-05-01

    65 Physical Impairment 66 Spatial disorientation. 67 Psychological condition. 71 Misused or failed to use flaps. 74 Left aircraft unattended, engine...ARTS III - (Software) (1975) 203 Weather Radar Display System (ASR - 57) 204 ATARS - Automated Terminal Area Radar Service (1974) 205 Instrument Landing...Generated Trauma, Pathological and Psychological Dysfunction accident causes. Collectively, the distribution of safety programs throughout the fault

  18. Station Blackout: A case study in the interaction of mechanistic and probabilistic safety analysis

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Curtis Smith; Diego Mandelli; Cristian Rabiti

    2013-11-01

    The ability to better characterize and quantify safety margins is important to improved decision making about nuclear power plant design, operation, and plant life extension. As research and development (R&D) in the light-water reactor (LWR) Sustainability (LWRS) Program and other collaborative efforts yield new data, sensors, and improved scientific understanding of physical processes that govern the aging and degradation of plant SSCs needs and opportunities to better optimize plant safety and performance will become known. The purpose of the Risk Informed Safety Margin Characterization (RISMC) Pathway R&D is to support plant decisions for risk-informed margin management with the aim tomore » improve economics, reliability, and sustain safety of current NPPs. In this paper, we describe the RISMC analysis process illustrating how mechanistic and probabilistic approaches are combined in order to estimate a safety margin. We use the scenario of a “station blackout” wherein offsite power and onsite power is lost, thereby causing a challenge to plant safety systems. We describe the RISMC approach, illustrate the station blackout modeling, and contrast this with traditional risk analysis modeling for this type of accident scenario.« less

  19. Who by accident? The social morphology of car accidents.

    PubMed

    Factor, Roni; Yair, Gad; Mahalel, David

    2010-09-01

    Prior studies in the sociology of accidents have shown that different social groups have different rates of accident involvement. This study extends those studies by implementing Bourdieu's relational perspective of social space to systematically explore the homology between drivers' social characteristics and their involvement in specific types of motor vehicle accident. Using a large database that merges official Israeli road-accident records with socioeconomic data from two censuses, this research maps the social order of road accidents through multiple correspondence analysis. Extending prior studies, the results show that different social groups indeed tend to be involved in motor vehicle accidents of different types and severity. For example, we find that drivers from low socioeconomic backgrounds are overinvolved in severe accidents with fatal outcomes. The new findings reported here shed light on the social regularity of road accidents and expose new facets in the social organization of death. © 2010 Society for Risk Analysis.

  20. 36 CFR 1004.4 - Report of motor vehicle accident.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... accident. 1004.4 Section 1004.4 Parks, Forests, and Public Property PRESIDIO TRUST VEHICLES AND TRAFFIC SAFETY § 1004.4 Report of motor vehicle accident. (a) The operator of a motor vehicle involved in an accident resulting in property damage, personal injury or death shall report the accident to the Executive...

  1. 36 CFR 1004.4 - Report of motor vehicle accident.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... accident. 1004.4 Section 1004.4 Parks, Forests, and Public Property PRESIDIO TRUST VEHICLES AND TRAFFIC SAFETY § 1004.4 Report of motor vehicle accident. (a) The operator of a motor vehicle involved in an accident resulting in property damage, personal injury or death shall report the accident to the Executive...

  2. 33 CFR 173.55 - Report of casualty or accident.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 33 Navigation and Navigable Waters 2 2011-07-01 2011-07-01 false Report of casualty or accident... (CONTINUED) BOATING SAFETY VESSEL NUMBERING AND CASUALTY AND ACCIDENT REPORTING Casualty and Accident Reporting § 173.55 Report of casualty or accident. (a) The operator of a vessel shall submit the casualty or...

  3. Safety in New Zealand's adventure tourism industry: the client accident experience of adventure tourism operators.

    PubMed

    Bentley , T A; Page, S J; Laird, I S

    2000-01-01

    Injuries and fatalities among participants of adventure tourism activities have the potential to seriously impact on New Zealand's tourism industry. However, the absence of statistics for tourist accidents in New Zealand, and the lack of detailed academic research into adventure tourism safety, means the extent of the problem is unknown. The aims of the present study were to determine the incidence of client injuries across a range of adventure tourism activity sectors, and to identify common accident events and contributory risk factors. A postal questionnaire survey of New Zealand adventure tourism operators was used. Operators were asked to provide information related to their business; the number of recorded client injuries during the preceding 12 month period, January to December 1998; common accident and injury events associated with their activity; and perceived risk factors for accidents in their sector of the adventure tourism industry. The survey was responded to by 142 New Zealand adventure tourism operators. The operators' reported client injury experience suggests the incidence of serious client injuries is very low. Highest client injury incidence rates were found for activities that involved the risk of falling from a moving vehicle or animal (e.g., cycle tours, quad biking, horse riding, and white-water rafting). Slips, trips, and falls on the level were common accident events across most sectors of the industry. Perceived accident/incident causes were most commonly related to the client, and in particular, failure to attend to and follow instructions. The prevalence of client injuries in activity sectors not presently covered by government regulation, suggests policy makers should look again at extending codes of practice to a wider range of adventure tourism activities. Further research considering adventure tourism involvement in overseas visitor hospitalized injuries in New Zealand, is currently in progress. This will provide supporting evidence

  4. A study of carburetor/induction system icing in general aviation accidents

    NASA Technical Reports Server (NTRS)

    Obermayer, R. W.; Roe, W. T.

    1975-01-01

    An assessment of the frequency and severity of carburetor/induction icing in general-aviation accidents was performed. The available literature and accident data from the National Transportation Safety Board were collected. A computer analysis of the accident data was performed. Between 65 and 90 accidents each year involve carburetor/induction system icing as a probable cause/factor. Under conditions conducive to carburetor/induction icing, between 50 and 70 percent of engine malfunction/failure accidents (exclusive of those due to fuel exhaustion) are due to carburetor/induction system icing. Since the evidence of such icing may not remain long after an accident, it is probable that the frequency of occurrence of such accidents is underestimated; therefore, some extrapolation of the data was conducted. The problem of carburetor/induction system icing is particularly acute for pilots with less than 1000 hours of total flying time. The severity of such accidents is about the same as any accident resulting from a forced landing or precautionary landing. About 144 persons, on the average, are exposed to death and injury each year in accidents involving carburetor/induction icing as a probable cause/factor.

  5. Wet weather highway accident analysis and skid resistance data management system (volume I).

    DOT National Transportation Integrated Search

    1992-06-01

    The objectives and scope of this research are to establish an effective methodology for wet weather accident analysis and to develop a database management system to facilitate information processing and storage for the accident analysis process, skid...

  6. Health effects model for nuclear power plant accident consequence analysis. Part I. Introduction, integration, and summary. Part II. Scientific basis for health effects models

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Evans, J.S.; Moeller, D.W.; Cooper, D.W.

    1985-07-01

    Analysis of the radiological health effects of nuclear power plant accidents requires models for predicting early health effects, cancers and benign thyroid nodules, and genetic effects. Since the publication of the Reactor Safety Study, additional information on radiological health effects has become available. This report summarizes the efforts of a program designed to provide revised health effects models for nuclear power plant accident consequence modeling. The new models for early effects address four causes of mortality and nine categories of morbidity. The models for early effects are based upon two parameter Weibull functions. They permit evaluation of the influence ofmore » dose protraction and address the issue of variation in radiosensitivity among the population. The piecewise-linear dose-response models used in the Reactor Safety Study to predict cancers and thyroid nodules have been replaced by linear and linear-quadratic models. The new models reflect the most recently reported results of the follow-up of the survivors of the bombings of Hiroshima and Nagasaki and permit analysis of both morbidity and mortality. The new models for genetic effects allow prediction of genetic risks in each of the first five generations after an accident and include information on the relative severity of various classes of genetic effects. The uncertainty in modeloling radiological health risks is addressed by providing central, upper, and lower estimates of risks. An approach is outlined for summarizing the health consequences of nuclear power plant accidents. 298 refs., 9 figs., 49 tabs.« less

  7. Bayesian road safety analysis: incorporation of past evidence and effect of hyper-prior choice.

    PubMed

    Miranda-Moreno, Luis F; Heydari, Shahram; Lord, Dominique; Fu, Liping

    2013-09-01

    This paper aims to address two related issues when applying hierarchical Bayesian models for road safety analysis, namely: (a) how to incorporate available information from previous studies or past experiences in the (hyper) prior distributions for model parameters and (b) what are the potential benefits of incorporating past evidence on the results of a road safety analysis when working with scarce accident data (i.e., when calibrating models with crash datasets characterized by a very low average number of accidents and a small number of sites). A simulation framework was developed to evaluate the performance of alternative hyper-priors including informative and non-informative Gamma, Pareto, as well as Uniform distributions. Based on this simulation framework, different data scenarios (i.e., number of observations and years of data) were defined and tested using crash data collected at 3-legged rural intersections in California and crash data collected for rural 4-lane highway segments in Texas. This study shows how the accuracy of model parameter estimates (inverse dispersion parameter) is considerably improved when incorporating past evidence, in particular when working with the small number of observations and crash data with low mean. The results also illustrates that when the sample size (more than 100 sites) and the number of years of crash data is relatively large, neither the incorporation of past experience nor the choice of the hyper-prior distribution may affect the final results of a traffic safety analysis. As a potential solution to the problem of low sample mean and small sample size, this paper suggests some practical guidance on how to incorporate past evidence into informative hyper-priors. By combining evidence from past studies and data available, the model parameter estimates can significantly be improved. The effect of prior choice seems to be less important on the hotspot identification. The results show the benefits of incorporating prior

  8. FY2017 Updates to the SAS4A/SASSYS-1 Safety Analysis Code

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Fanning, T. H.

    The SAS4A/SASSYS-1 safety analysis software is used to perform deterministic analysis of anticipated events as well as design-basis and beyond-design-basis accidents for advanced fast reactors. It plays a central role in the analysis of U.S. DOE conceptual designs, proposed test and demonstration reactors, and in domestic and international collaborations. This report summarizes the code development activities that have taken place during FY2017. Extensions to the void and cladding reactivity feedback models have been implemented, and Control System capabilities have been improved through a new virtual data acquisition system for plant state variables and an additional Block Signal for a variablemore » lag compensator to represent reactivity feedback for novel shutdown devices. Current code development and maintenance needs are also summarized in three key areas: software quality assurance, modeling improvements, and maintenance of related tools. With ongoing support, SAS4A/SASSYS-1 can continue to fulfill its growing role in fast reactor safety analysis and help solidify DOE’s leadership role in fast reactor safety both domestically and in international collaborations.« less

  9. Estimating the causes of traffic accidents using logistic regression and discriminant analysis.

    PubMed

    Karacasu, Murat; Ergül, Barış; Altin Yavuz, Arzu

    2014-01-01

    Factors that affect traffic accidents have been analysed in various ways. In this study, we use the methods of logistic regression and discriminant analysis to determine the damages due to injury and non-injury accidents in the Eskisehir Province. Data were obtained from the accident reports of the General Directorate of Security in Eskisehir; 2552 traffic accidents between January and December 2009 were investigated regarding whether they resulted in injury. According to the results, the effects of traffic accidents were reflected in the variables. These results provide a wealth of information that may aid future measures toward the prevention of undesired results.

  10. Directory of aerospace safety specialized information sources

    NASA Technical Reports Server (NTRS)

    Fullerton, E. A.; Rubens, L. S.; Mandel, G.; Mckenna, P. J.

    1974-01-01

    Directory aids safety specialists in locating information sources and individual experts in engineering-related fields. Lists 170 organizations and approximately 300 individuals who can provide safety-related technical information in form of documentation, data, and consulting expertise. Information on hazard and failure cause identification, accident analysis, and materials characteristics are covered.

  11. Transport aircraft accident dynamics

    NASA Technical Reports Server (NTRS)

    Cominsky, A.

    1982-01-01

    A study was carried out of 112 impact survivable jet transport aircraft accidents (world wide) of 27,700 kg (60,000 lb.) aircraft and up extending over the last 20 years. This study centered on the effect of impact and the follow-on events on aircraft structures and was confined to the approach, landing and takeoff segments of the flight. The significant characteristics, frequency of occurrence and the effect on the occupants of the above data base were studied and categorized with a view to establishing typical impact scenarios for use as a basis of verifying the effectiveness of potential safety concepts. Studies were also carried out of related subjects such as: (1) assessment of advanced materials; (2) human tolerance to impact; (3) merit functions for safety concepts; and (4) impact analysis and test methods.

  12. Final safety analysis report for the Galileo mission: Volume 3 (Book 2), Nuclear risk analysis document: Appendices: Revision 1

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Not Available

    1989-01-25

    It is the purpose of the NRAD to provide an analysis of the range of potential consequences of accidents which have been identified that are associated with the launching and deployment of the Galileo mission spacecraft. The specific consequences analyzed are those associated with the possible release of radioactive material (fuel) of the Radioisotope Thermoelectric Generators (RTGs). They are in terms of radiation doses to people and areas of deposition of radioactive material. These consequence analyses can be used in several ways. One way is to identify the potential range of consequences which might have to be dealt with ifmore » there were to be an accident with a release of fuel, so as to assure that, given such an accident, the health and safety of the public will be reasonably protected. Another use of the information, in conjunction with accident and release probabilities, is to estimate the risks associated with the mission. That is, most space launches occur without incident. Given an accident, the most probable result relative to the RTGs is complete containment of the radioactive material. Only a small fraction of accidents might result in a release of fuel and subsequent radiological consequences. The combination of probability with consequence is risk, which can be compared to other human and societal risks to assure that no undue risks are implied by undertaking the mission. Book 2 contains eight appendices.« less

  13. Accident Prevention: A Workers' Education Manual.

    ERIC Educational Resources Information Center

    International Labour Office, Geneva (Switzerland).

    Devoted to providing industrial workers with a greater knowledge of precautionary measures undertaken and enforced by industries for the protection of workers, this safety education manual contains 14 lessons ranging from "The Problems of Accidents during Work" to "Trade Unions and Workers and Industrial Safety." Fire protection, safety equipment…

  14. Credible investigation of air accidents.

    PubMed

    Smart, K

    2004-07-26

    Within the United Kingdom the Air Accidents Investigation Branch (AAIB) has been used as a model for the other transport modes accident investigation bodies. Government Ministers considered that the AAIB's approach had established the trust of the public and the aviation industry in its ability to conduct independent and objective investigations. The paper will examine the factors that are involved in establishing this trust. They include: the investigation framework; the actual and perceived independence of the accident investigating body; the aviation industry's safety culture; the qualities of the investigators and the quality of their liaison with bereaved families those directly affected by the accidents they investigate.

  15. [A spatially explicit analysis of traffic accidents involving pedestrians and cyclists in Berlin].

    PubMed

    Lakes, Tobia

    2017-12-01

    In many German cities and counties, sustainable mobility concepts that strengthen pedestrian and cyclist traffic are promoted. From the perspectives of urban development, traffic planning and public healthcare, a spatially differentiated analysis of traffic accident data is decisive. 1) The identification of spatial and temporal patterns of the distribution of accidents involving cyclists and pedestrians, 2) the identification of hotspots and exploration of possible underlying causes and 3) the critical discussion of benefits and challenges of the results and the derivation of conclusions. Spatio-temporal distributions of data from accident statistics in Berlin involving pedestrians and cyclists from 2011 to 2015 were analysed with geographic information systems (GIS). While the total number of accidents remains relatively stable for pedestrian and cyclist accidents, the spatial distribution analysis shows, however, that there are significant spatial clusters (hotspots) of traffic accidents with a strong concentration in the inner city area. In a critical discussion, the benefits of geographic concepts are identified, such as spatially explicit health data (in this case traffic accident data), the importance of the integration of other data sources for the evaluation of the health impact of areas (traffic accident statistics of the police), and the possibilities and limitations of spatial-temporal data analysis (spatial point-density analyses) for the derivation of decision-supported recommendations and for the evaluation of policy measures of health prevention and of health-relevant urban development.

  16. Comparing the Identification of Recommendations by Different Accident Investigators Using a Common Methodology

    NASA Technical Reports Server (NTRS)

    Johnson, Chris W.; Oltedal, H. A.; Holloway, C. M.

    2012-01-01

    Accident reports play a key role in the safety of complex systems. These reports present the recommendations that are intended to help avoid any recurrence of past failures. However, the value of these findings depends upon the causal analysis that helps to identify the reasons why an accident occurred. Various techniques have been developed to help investigators distinguish root causes from contributory factors and contextual information. This paper presents the results from a study into the individual differences that can arise when a group of investigators independently apply the same technique to identify the causes of an accident. This work is important if we are to increase the consistency and coherence of investigations following major accidents.

  17. Analysis on tank truck accidents involved in road hazardous materials transportation in china.

    PubMed

    Shen, Xiaoyan; Yan, Ying; Li, Xiaonan; Xie, Chenjiang; Wang, Lihua

    2014-01-01

    Due to the sheer size and capacity of the tanker and the properties of cargo transported in the tank, hazmat tanker accidents are more disastrous than other types of vehicle accidents. The aim of this study was to provide a current survey on the situation of accidents involving tankers transporting hazardous materials in China. Detailed descriptions of 708 tanker accidents associated with hazmat transportation in China from 2004 to 2011 were analyzed to identify causes, location, types, time of occurrence, hazard class for materials involved, consequences, and the corresponding probability. Hazmat tanker accidents mainly occurred in eastern (38.1%) and southwest China (12.3%). The most frequent hazmat tanker accidents involved classes 2, 3, and 8. The predominant accident types were rollover (29.10%), run-off-the-road (16.67%), and rear-end collisions (13.28%), with a high likelihood of a large spill occurring. About 55.93% of the accidents occurred on freeways and class 1 roads, with the spill percentage reaching 75.00% and the proportion of spills that occurred in the total accidents amounting to 77.82%, of which 61.72% are considered large spills. The month with the highest accident probability was July (12.29%), and most crashes occurred during the early morning (4:00-6:00 a.m.) and midday (10:00 a.m.-12:00 p.m.) hours, 19.63% versus 16.10%. Human-related errors (73.8%) and vehicle-related defects (19.6%) were the primary reasons for hazmat tanker crashes. The most common outcomes of a hazmat tanker accident was a spill without further events (55.51%), followed by a release with fire (7.77%), and release with an explosion (2.54%). The safety situation of China's hazmat tanker transportation is grim. Such accidents not only have high spill percentages and consistently large spills but they can also cause serious consequences, such as fires and explosions. Improving the training of drivers and the quality of vehicles, deploying roll stability aids, enhancing

  18. Estimation of fatality and injury risk by means of in-depth fatal accident investigation data.

    PubMed

    Yannis, George; Papadimitriou, Eleonora; Dupont, Emmanuelle; Martensen, Heike

    2010-10-01

    In this article the factors affecting fatality and injury risk of road users involved in fatal accidents are analyzed by means of in-depth accident investigation data, with emphasis on parameters not extensively explored in previous research. A fatal accident investigation (FAI) database is used, which includes intermediate-level in-depth data for a harmonized representative sample of 1300 fatal accidents in 7 European countries. The FAI database offers improved potential for analysis, because it includes information on a number of variables that are seldom available, complete, or accurately recorded in road accident databases. However, the fact that only fatal accidents are examined requires for methodological adjustments, namely, the correction for two types of effects on a road user's baseline risk: "accident size" effects, and "relative vulnerability" effects. Fatality and injury risk can be then modeled through multilevel logistic regression models, which account for the hierarchical dependences of the road accident process. The results show that the baseline fatality risk of road users involved in fatal accidents decreases with accident size and increases with the vulnerability of the road user. On the contrary, accident size increases nonfatal injury risk of road users involved in fatal accidents. Other significant effects on fatality and injury risk in fatal accidents include road user age, vehicle type, speed limit, the chain of accident events, vehicle maneuver, and safety equipment. In particular, the presence and use of safety equipment such as seat belt, antilock braking system (ABS), and electronic stability program (ESP) are protection factors for car occupants, especially for those seated at the front seats. Although ABS and ESP systems are typically associated with positive effects on accident occurrence, the results of this research revealed significant related effects on accident severity as well. Moreover, accident consequences are more severe

  19. Implementation of a novel taxonomy based on cognitive work analysis in the assessment of safety performance.

    PubMed

    Niskanen, Toivo

    2017-12-12

    The aim of this study was to examine how the developed taxonomy of cognitive work analysis (CWA) can be applied in combination with statistical analysis regarding different sociotechnical categories. This study applied a combination of quantitative and qualitative methodologies. Workers (n = 120) and managers (n = 85) in the chemical industry were asked in a questionnaire how different occupational safety and health (OSH) measures were being implemented. The exploration of the qualitative CWA taxonomy consisted of an analysis of the following topics: (a) work domain; (b) control task; (c) strategies; (d) social organization and cooperation; (e) worker competencies. The following hypotheses were supported - activities of the management had positive impacts on the aggregated variables: near-accident investigation and instructions (H 1 ); OSH training (H 2 ); operations, technical processes and safe use of chemicals (H 3 ); use of personal protective equipment (H 4 ); measuring, follow-up and prevention of major accidents (H 5 ). The CWA taxonomy was applied in mixed methods when testing H 1 -H 5 . A special approach is to analyze the work demands of complex sociotechnical systems with the taxonomy of CWA. In problem-solving, the CWA taxonomy should seek to capitalize on the strengths and minimize the limitations of safety performance.

  20. British army air corps accidents, 1991-2010: a review of contrasting decades.

    PubMed

    Adams, Mark S; Curry, Ian P; Gaydos, Steven J

    2014-08-01

    Accident investigation and review are important not only to attribute failure modes, but also mitigate risk, improve safety, and enhance capability. It was hypothesized that an interesting perspective on British Army Air Corps (AAC) rotary-wing (RW) accidents may be garnered by contrasting data from the previous two decades with a general operational (OP) shift from European theaters of conflict to operations in Southwest Asia. AAC mishaps for the period from January 1991 through December 2010 were reviewed within an air safety management system. Accidents, defined by category 4 or 5 aircraft damage or death or major injury of personnel, were selected. Analysis was conducted jointly by a minimum of two specialists in aviation medicine. There were 37 accidents that occurred in 6 differing airframes at an average rate of 2.5 per 100,000 flying hours. From 1991-2000, 25 accidents (9 OP) occurred with a rate of 2.8 per 100,000 flying hours. From 2001-2010, 12 accidents (5 OP) occurred with a rate of 2.1 per 100,000 flying hours. Aircrew human factors (HF) errors represented 84% of attributable causation for both decades. Spatial disorientation (SD) represented a higher proportion of HF-related accidents for OP flying. Despite the perception of a more difficult OP theater for the latter decade, the overall rate and the proportion of OP accidents did not differ appreciably. Rather than theater-specific threats or challenges, it has been the longstanding and prominent player of HF error and specifically SD in OP flying that has remained entrenched in the causal chain.

  1. French policy for managing the post-accident phase of a nuclear accident.

    PubMed

    Gallay, F; Godet, J L; Niel, J C

    2015-06-01

    In 2005, at the request of the French Government, the Nuclear Safety Authority (ASN) established a Steering Committee for the Management of the Post-Accident Phase of a Nuclear Accident or a Radiological Emergency, with the objective of establishing a policy framework. Under the supervision of ASN, this Committee, involving several tens of experts from different backgrounds (e.g. relevant ministerial offices, expert agencies, local information commissions around nuclear installations, non-governmental organisations, elected officials, licensees, and international experts), developed a number of recommendations over a 7-year period. First published in November 2012, these recommendations cover the immediate post-emergency situation, and the transition and longer-term periods of the post-accident phase in the case of medium-scale nuclear accidents causing short-term radioactive release (less than 24 h) that might occur at French nuclear facilities. They also apply to actions to be undertaken in the event of accidents during the transportation of radioactive materials. These recommendations are an important first step in preparation for the management of a post-accident situation in France in the case of a nuclear accident. © The Chartered Institution of Building Services Engineers 2014.

  2. Applying the AcciMap methodology to investigate the tragic Sewol Ferry accident in South Korea.

    PubMed

    Lee, Samuel; Moh, Young Bo; Tabibzadeh, Maryam; Meshkati, Najmedin

    2017-03-01

    This study applies the AcciMap methodology, which was originally proposed by Professor Jens Rasmussen (1997), to the analysis of the tragic Sewol Ferry accident in South Korea on April 16, 2014, which killed 304 mostly young people and is considered as a national disaster in that country. This graphical representation, by incorporating associated socio-technical factors into an integrated framework, provides a big-picture to illustrate the context in which an accident occurred as well as the interactions between different levels of the studied system that resulted in that event. In general, analysis of past accidents within the stated framework can define the patterns of hazards within an industrial sector. Such analysis can lead to the definition of preconditions for safe operations, which is a main focus of proactive risk management systems. In the case of the Sewol Ferry accident, a lot of the blame has been placed on the Sewol's captain and its crewmembers. However, according to this study, which relied on analyzing all available sources published in English and Korean, the disaster is the result of a series of lapses and disregards for safety across different levels of government and regulatory bodies, Chonghaejin Company, and the Sewol's crewmembers. The primary layers of the AcciMap framework, which include the political environment and non-proactive governmental body; inadequate regulations and their lax oversight and enforcement; poor safety culture; inconsideration of human factors issues; and lack of and/or outdated standard operating and emergency procedures were not only limited to the maritime industry in South Korea, and the Sewol Ferry accident, but they could also subject any safety-sensitive industry anywhere in the world. Copyright © 2016 Elsevier Ltd. All rights reserved.

  3. Predicting and analyzing the trend of traffic accidents deaths in Iran in 2014 and 2015.

    PubMed

    Mehmandar, Mohammadreza; Soori, Hamid; Mehrabi, Yadolah

    2016-01-01

    Predicting the trend in traffic accidents deaths and its analysis can be a useful tool for planning and policy-making, conducting interventions appropriate with death trend, and taking the necessary actions required for controlling and preventing future occurrences. Predicting and analyzing the trend of traffic accidents deaths in Iran in 2014 and 2015. It was a cross-sectional study. All the information related to fatal traffic accidents available in the database of Iran Legal Medicine Organization from 2004 to the end of 2013 were used to determine the change points (multi-variable time series analysis). Using autoregressive integrated moving average (ARIMA) model, traffic accidents death rates were predicted for 2014 and 2015, and a comparison was made between this rate and the predicted value in order to determine the efficiency of the model. From the results, the actual death rate in 2014 was almost similar to that recorded for this year, while in 2015 there was a decrease compared with the previous year (2014) for all the months. A maximum value of 41% was also predicted for the months of January and February, 2015. From the prediction and analysis of the death trends, proper application and continuous use of the intervention conducted in the previous years for road safety improvement, motor vehicle safety improvement, particularly training and culture-fostering interventions, as well as approval and execution of deterrent regulations for changing the organizational behaviors, can significantly decrease the loss caused by traffic accidents.

  4. Effects of health and safety problem recognition on small business facility investment

    PubMed Central

    2013-01-01

    Objectives This study involved a survey of the facility investment experiences, which was designed to recognize the importance of health and safety problems, and industrial accident prevention. Ultimately, we hope that small scale industries will create effective industrial accident prevention programs and facility investments. Methods An individual survey of businesses’ present physical conditions, recognition of the importance of the health and safety problems, and facility investment experiences for preventing industrial accidents was conducted. The survey involved 1,145 business operators or management workers in small business places with fewer than 50 workers in six industrial complexes. Results Regarding the importance of occupational health and safety problems (OHS), 54.1% said it was “very important”. Received technical and financial support, and industrial accidents that occurred during the past three years were recognized as highly important for OHS. In an investigation regarding facility investment experiences for industrial accident prevention, the largest factors were business size, greater numbers of industrial accidents, greater technical and financial support received, and greater recognition of the importance of the OHS. The related variables that decided facility investment for industry accident prevention in a logistic regression analysis were the experiences of business facilities where industrial accidents occurred during the past three years, received technical and financial support, and recognition of the OHS. Those considered very important were shown to be highly significant. Conclusions Recognition of health and safety issues was higher when small businesses had experienced industrial accidents or received financial support. The investment in industrial accidents was greater when health and safety issues were recognized as important. Therefore, the goal of small business health and safety projects is to prioritize health and safety

  5. Effects of health and safety problem recognition on small business facility investment.

    PubMed

    Park, Jisu; Jeong, Harin; Hong, Sujin; Park, Jong-Tae; Kim, Dae-Sung; Kim, Jongseo; Kim, Hae-Joon

    2013-10-23

    This study involved a survey of the facility investment experiences, which was designed to recognize the importance of health and safety problems, and industrial accident prevention. Ultimately, we hope that small scale industries will create effective industrial accident prevention programs and facility investments. An individual survey of businesses' present physical conditions, recognition of the importance of the health and safety problems, and facility investment experiences for preventing industrial accidents was conducted. The survey involved 1,145 business operators or management workers in small business places with fewer than 50 workers in six industrial complexes. Regarding the importance of occupational health and safety problems (OHS), 54.1% said it was "very important". Received technical and financial support, and industrial accidents that occurred during the past three years were recognized as highly important for OHS. In an investigation regarding facility investment experiences for industrial accident prevention, the largest factors were business size, greater numbers of industrial accidents, greater technical and financial support received, and greater recognition of the importance of the OHS. The related variables that decided facility investment for industry accident prevention in a logistic regression analysis were the experiences of business facilities where industrial accidents occurred during the past three years, received technical and financial support, and recognition of the OHS. Those considered very important were shown to be highly significant. Recognition of health and safety issues was higher when small businesses had experienced industrial accidents or received financial support. The investment in industrial accidents was greater when health and safety issues were recognized as important. Therefore, the goal of small business health and safety projects is to prioritize health and safety issues in terms of business management and

  6. Domino effect in chemical accidents: main features and accident sequences.

    PubMed

    Darbra, R M; Palacios, Adriana; Casal, Joaquim

    2010-11-15

    The main features of domino accidents in process/storage plants and in the transportation of hazardous materials were studied through an analysis of 225 accidents involving this effect. Data on these accidents, which occurred after 1961, were taken from several sources. Aspects analyzed included the accident scenario, the type of accident, the materials involved, the causes and consequences and the most common accident sequences. The analysis showed that the most frequent causes are external events (31%) and mechanical failure (29%). Storage areas (35%) and process plants (28%) are by far the most common settings for domino accidents. Eighty-nine per cent of the accidents involved flammable materials, the most frequent of which was LPG. The domino effect sequences were analyzed using relative probability event trees. The most frequent sequences were explosion→fire (27.6%), fire→explosion (27.5%) and fire→fire (17.8%). Copyright © 2010 Elsevier B.V. All rights reserved.

  7. Assessing flight safety differences between the United States regional and major airlines

    NASA Astrophysics Data System (ADS)

    Sharp, Broderick H.

    During 2008, the U.S. domestic airline departures exceeded 28,000 flights per day. Thirty-nine or less than 0.2 of 1% of these flights resulted in operational incidents or accidents. However, even a low percentage of airline accidents and incidents continue to cause human suffering and property loss. The charge of this study was the comparison of U.S. major and regional airline safety histories. The study spans safety events from January 1982 through December 2008. In this quantitative analysis, domestic major and regional airlines were statistically tested for their flight safety differences. Four major airlines and thirty-seven regional airlines qualified for the safety study which compared the airline groups' fatal accidents, incidents, non-fatal accidents, pilot errors, and the remaining six safety event probable cause types. The six other probable cause types are mechanical failure, weather, air traffic control, maintenance, other, and unknown causes. The National Transportation Safety Board investigated each airline safety event, and assigned a probable cause to each event. A sample of 500 events was randomly selected from the 1,391 airlines' accident and incident population. The airline groups' safety event probabilities were estimated using the least squares linear regression. A probability significance level of 5% was chosen to conclude the appropriate research question hypothesis. The airline fatal accidents and incidents probability levels were 1.2% and 0.05% respectively. These two research questions did not reach the 5% significance level threshold. Therefore, the airline groups' fatal accidents and non-destructive incidents probabilities favored the airline groups' safety differences hypothesis. The linear progression estimates for the remaining three research questions were 71.5% for non-fatal accidents, 21.8% for the pilot errors, and 7.4% significance level for the six probable causes. These research questions' linear regressions are greater than

  8. Social disorder, accidents, and municipal wildfires

    Treesearch

    Douglas S. Thomas; David T. Butry; Jeffrey P. Prestemon

    2012-01-01

    Societal safeguards, established by those who have shared perceptions of the importance of safety and taking preventative measures, reduce the incidence of accidents that harm people and damage property. These safeguards prevent or discourage community members from partaking in careless behaviors that often lead to accidents. Wildland urban interface communities that...

  9. Risk analysis of emergent water pollution accidents based on a Bayesian Network.

    PubMed

    Tang, Caihong; Yi, Yujun; Yang, Zhifeng; Sun, Jie

    2016-01-01

    To guarantee the security of water quality in water transfer channels, especially in open channels, analysis of potential emergent pollution sources in the water transfer process is critical. It is also indispensable for forewarnings and protection from emergent pollution accidents. Bridges above open channels with large amounts of truck traffic are the main locations where emergent accidents could occur. A Bayesian Network model, which consists of six root nodes and three middle layer nodes, was developed in this paper, and was employed to identify the possibility of potential pollution risk. Dianbei Bridge is reviewed as a typical bridge on an open channel of the Middle Route of the South to North Water Transfer Project where emergent traffic accidents could occur. Risk of water pollutions caused by leakage of pollutants into water is focused in this study. The risk for potential traffic accidents at the Dianbei Bridge implies a risk for water pollution in the canal. Based on survey data, statistical analysis, and domain specialist knowledge, a Bayesian Network model was established. The human factor of emergent accidents has been considered in this model. Additionally, this model has been employed to describe the probability of accidents and the risk level. The sensitive reasons for pollution accidents have been deduced. The case has also been simulated that sensitive factors are in a state of most likely to lead to accidents. Copyright © 2015 Elsevier Ltd. All rights reserved.

  10. Designing for auto safety

    NASA Technical Reports Server (NTRS)

    Driver, E. T.

    1971-01-01

    Safety design features in the motor vehicle and highway construction fields result from systems analysis approach to prevent or lessen death, injury, and property damage results. Systems analysis considers the prevention of crashes, increased survivability in crashes, and prompt medical attention to injuries as well as other postcrash salvage measures. The interface of these system elements with the driver, the vehicle, and the environment shows that action on the vehicle system produces the greatest safety payoff through design modifications. New and amended safety standards developed through hazard analysis technique improved accident statistics in the 70'; these regulations include driver qualifications and countermeasures to identify the chronic drunken driver who is involved in more than two-thirds of all auto deaths.

  11. Biomechanical analysis of occupant kinematics in rollover motor vehicle accidents: dynamic spit test.

    PubMed

    Sances, Anthony; Kumaresan, Srirangam; Clarke, Richard; Herbst, Brian; Meyer, Steve

    2005-01-01

    A better understanding of occupant kinematics in rollover accidents helps to advance biomechanical knowledge and to enhance the safety features of motor vehicles. While many rollover accident simulation studies have adopted the static approach to delineate the occupant kinematics in rollover accidents, very few studies have attempted the dynamic approach. The present work was designed to study the biomechanics of restrained occupants during rollover accidents using the steady-state dynamic spit test and to address the importance of keeping the lap belt fastened. Experimental tests were conducted using an anthropometric 50% Hybrid III dummy in a vehicle. The vehicle was rotated at 180 degrees/second and the dummy was restrained using a standard three-point restraint system. The lap belt of the dummy was fastened either by using the cinching latch plate or by locking the retractor. Three configurations of shoulder belt harness were simulated: shoulder belt loose on chest with cinch plate, shoulder belt under the left arm and shoulder belt behind the chest. In all tests, the dummy stayed within the confinement of the vehicle indicating that the securely fastened lap belt holds the dummy with dynamic movement of 3 1/2" to 4". The results show that occupant movement in rollover accidents is least affected by various shoulder harness positions with a securely fastened lap belt. The present study forms a first step in delineating the biomechanics of occupants in rollover accidents.

  12. Incorporating real-time traffic and weather data to explore road accident likelihood and severity in urban arterials.

    PubMed

    Theofilatos, Athanasios

    2017-06-01

    The effective treatment of road accidents and thus the enhancement of road safety is a major concern to societies due to the losses in human lives and the economic and social costs. The investigation of road accident likelihood and severity by utilizing real-time traffic and weather data has recently received significant attention by researchers. However, collected data mainly stem from freeways and expressways. Consequently, the aim of the present paper is to add to the current knowledge by investigating accident likelihood and severity by exploiting real-time traffic and weather data collected from urban arterials in Athens, Greece. Random Forests (RF) are firstly applied for preliminary analysis purposes. More specifically, it is aimed to rank candidate variables according to their relevant importance and provide a first insight on the potential significant variables. Then, Bayesian logistic regression as well finite mixture and mixed effects logit models are applied to further explore factors associated with accident likelihood and severity respectively. Regarding accident likelihood, the Bayesian logistic regression showed that variations in traffic significantly influence accident occurrence. On the other hand, accident severity analysis revealed a generally mixed influence of traffic variations on accident severity, although international literature states that traffic variations increase severity. Lastly, weather parameters did not find to have a direct influence on accident likelihood or severity. The study added to the current knowledge by incorporating real-time traffic and weather data from urban arterials to investigate accident occurrence and accident severity mechanisms. The identification of risk factors can lead to the development of effective traffic management strategies to reduce accident occurrence and severity of injuries in urban arterials. Copyright © 2017 Elsevier Ltd and National Safety Council. All rights reserved.

  13. Analysis of Loss-of-Coolant Accidents in the NIST Research Reactor - Early Phase

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Baek, Joo S.; Diamond, David

    A study of the fuel temperature during the early phase of a loss-of-coolant accident (LOCA) in the NIST research reactor (NBSR) was completed. Previous studies had been reported in the preliminary safety analysis report for the conversion of the NBSR from high-enriched uranium (HEU) fuel to low-enriched (LEU) fuel. Those studies had focused on the most vulnerable LOCA situation, namely, a double-ended guillotine break in the time period after reactor trip when water is drained from either the coolant channels inside the fuel elements or the region outside the fuel elements. The current study fills in a gap in themore » analysis which is the early phase of the event when there may still be water present but the reactor is at power or immediately after reactor trip and pumps have tripped. The calculations were done, for both the current HEU-fueled core and the proposed LEU core, with the TRACE thermal-hydraulic systems code. Several break locations and different break sizes were considered. In all cases the increase in the clad (or fuel meat) temperature was relatively small so that a large margin to the temperature threshold for blistering (the Safety Limit for the NBSR) remained.« less

  14. Occupational safety of different industrial sectors in Khartoum State, Sudan. Part 1: Safety performance evaluation.

    PubMed

    Zaki, Gehan R; El-Marakby, Fadia A; H Deign El-Nor, Yasser; Nofal, Faten H; Zakaria, Adel M

    2012-12-01

    Safety performance evaluation enables decision makers improve safety acts. In Sudan, accident records, statistics, and safety performance were not evaluated before maintenance of accident records became mandatory in 2005. This study aimed at evaluating and comparing safety performance by accident records among different cities and industrial sectors in Khartoum state, Sudan, during the period from 2005 to 2007. This was a retrospective study, the sample in which represented all industrial enterprises in Khartoum state employing 50 workers or more. All industrial accident records of the Ministry of Manpower and Health and those of different enterprises during the period from 2005 to 2007 were reviewed. The safety performance indicators used within this study were the frequency-severity index (FSI) and fatal and disabling accident frequency rates (DAFR). In Khartoum city, the FSI [0.10 (0.17)] was lower than that in Bahari [0.11 (0.21)] and Omdurman [0.84 (0.34)]. It was the maximum in the chemical sector [0.33 (0.64)] and minimum in the metallurgic sector [0.09 (0.19)]. The highest DAFR was observed in Omdurman [5.6 (3.5)] and in the chemical sector [2.5 (4.0)]. The fatal accident frequency rate in the mechanical and electrical engineering industry was the highest [0.0 (0.69)]. Male workers who were older, divorced, and had lower levels of education had the lowest safety performance indicators. The safety performance of the industrial enterprises in Khartoum city was the best. The safety performance in the chemical sector was the worst with regard to FSI and DAFR. The age, sex, and educational level of injured workers greatly affect safety performance.

  15. Safety analysis, risk assessment, and risk acceptance criteria

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Jamali, K.; Stack, D.W.; Sullivan, L.H.

    1997-08-01

    This paper discusses a number of topics that relate safety analysis as documented in the Department of Energy (DOE) safety analysis reports (SARs), probabilistic risk assessments (PRA) as characterized primarily in the context of the techniques that have assumed some level of formality in commercial nuclear power plant applications, and risk acceptance criteria as an outgrowth of PRA applications. DOE SARs of interest are those that are prepared for DOE facilities under DOE Order 5480.23 and the implementing guidance in DOE STD-3009-94. It must be noted that the primary area of application for DOE STD-3009 is existing DOE facilities andmore » that certain modifications of the STD-3009 approach are necessary in SARs for new facilities. Moreover, it is the hazard analysis (HA) and accident analysis (AA) portions of these SARs that are relevant to the present discussions. Although PRAs can be qualitative in nature, PRA as used in this paper refers more generally to all quantitative risk assessments and their underlying methods. HA as used in this paper refers more generally to all qualitative risk assessments and their underlying methods that have been in use in hazardous facilities other than nuclear power plants. This discussion includes both quantitative and qualitative risk assessment methods. PRA has been used, improved, developed, and refined since the Reactor Safety Study (WASH-1400) was published in 1975 by the Nuclear Regulatory Commission (NRC). Much debate has ensued since WASH-1400 on exactly what the role of PRA should be in plant design, reactor licensing, `ensuring` plant and process safety, and a large number of other decisions that must be made for potentially hazardous activities. Of particular interest in this area is whether the risks quantified using PRA should be compared with numerical risk acceptance criteria (RACs) to determine whether a facility is `safe.` Use of RACs requires quantitative estimates of consequence frequency and magnitude.« less

  16. 49 CFR 195.52 - Immediate notice of certain accidents.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Immediate notice of certain accidents. 195.52... TRANSPORTATION OF HAZARDOUS LIQUIDS BY PIPELINE Annual, Accident, and Safety-Related Condition Reporting § 195.52 Immediate notice of certain accidents. (a) Notice requirements. At the earliest practicable moment following...

  17. Quad City Intersection Traffic Accident Study: 1993 Data

    DOT National Transportation Integrated Search

    1996-03-01

    Accident information is an important factor from which to work towards the : regional Transportation System Management (TSM) objective of improving the : safety of the local transportation system. The 1993 Quad City Intersection : Traffic Accident Re...

  18. Model-Based Safety Analysis

    NASA Technical Reports Server (NTRS)

    Joshi, Anjali; Heimdahl, Mats P. E.; Miller, Steven P.; Whalen, Mike W.

    2006-01-01

    System safety analysis techniques are well established and are used extensively during the design of safety-critical systems. Despite this, most of the techniques are highly subjective and dependent on the skill of the practitioner. Since these analyses are usually based on an informal system model, it is unlikely that they will be complete, consistent, and error free. In fact, the lack of precise models of the system architecture and its failure modes often forces the safety analysts to devote much of their effort to gathering architectural details about the system behavior from several sources and embedding this information in the safety artifacts such as the fault trees. This report describes Model-Based Safety Analysis, an approach in which the system and safety engineers share a common system model created using a model-based development process. By extending the system model with a fault model as well as relevant portions of the physical system to be controlled, automated support can be provided for much of the safety analysis. We believe that by using a common model for both system and safety engineering and automating parts of the safety analysis, we can both reduce the cost and improve the quality of the safety analysis. Here we present our vision of model-based safety analysis and discuss the advantages and challenges in making this approach practical.

  19. Risk Analysis for Public Consumption: Media Coverage of the Ginna Nuclear Reactor Accident.

    ERIC Educational Resources Information Center

    Dunwoody, Sharon; And Others

    Researchers have determined that the lay public makes risk judgments in ways that are very different from those advocated by scientists. Noting that these differences have caused considerable concern among those who promote and regulate health and safety, a study examined media coverage of the accident at the Robert E. Ginna nuclear power plant…

  20. Accident frequency and unrealistic optimism: Children's assessment of risk.

    PubMed

    Joshi, Mary Sissons; Maclean, Morag; Stevens, Claire

    2018-02-01

    Accidental injury is a major cause of mortality and morbidity among children, warranting research on their risk perceptions. Three hundred and seven children aged 10-11 years assessed the frequency, danger and personal risk likelihood of 8 accidents. Two social-cognitive biases were manifested. The frequency of rare accidents (e.g. drowning) was overestimated, and the frequency of common accidents (e.g. bike accidents) underestimated; and the majority of children showed unrealistic optimism tending to see themselves as less likely to suffer these accidents in comparison to their peers, offering superior skills or parental control of the environment as an explanation. In the case of pedestrian accidents, children recognised their seriousness, underestimated the frequency of this risk and regarded their own road crossing skill as protection. These findings highlight the challenging task facing safety educators who, when teaching conventional safety knowledge and routines, also need to alert children to the danger of over-confidence without disabling them though fear. Copyright © 2017 Elsevier Ltd. All rights reserved.

  1. Safety culture : a significant influence on safety in transportation

    DOT National Transportation Integrated Search

    2017-08-01

    An organizations safety culture can influence safety outcomes. Research and experience show that when safety culture is strong, accidents are less frequent and less severe. As a result, building and maintaining strong safety cultures should be a t...

  2. The Impact of In-Vehicle Cell-Phone Use on Accidents or Near-Accidents among College Students.

    ERIC Educational Resources Information Center

    Seo, Dong-Chul; Torabi, Mohammad R.

    2004-01-01

    With in-vehicle use of cell phones rapidly increasing, the safety of young drivers, who represent 14% of licensed drivers but 26% of drivers involved in fatal crashes, may be disproportionately threatened. The authors used a questionnaire to examine the association between in-vehicle cell-phone use and accidents or near-accidents among 1,291…

  3. Aircraft accidents.method of analysis

    NASA Technical Reports Server (NTRS)

    1937-01-01

    This report is a revision of NACA-TR-357. It was prepared by the Committee on Aircraft Accidents. The purpose of this report is to provide a basis for the classification and comparison of aircraft accidents, both civil and military.

  4. Preliminary analysis of the National Crash Severity Study : factors in fatal accidents

    DOT National Transportation Integrated Search

    1979-06-01

    This study investigates the fatalities on the National Crash Severity Study (NCSS) of towaway, passenger car accidents. The analysis is in three stages. First, NCSS fatalities are compared to the fatally-injured occupants reported on the Fatal Accide...

  5. Civilian helicopter accidents into water: analysis of 46 cases, 1979-2006.

    PubMed

    Brooks, Christopher James; MacDonald, Conor Vaughan; Donati, Leo; Taber, Michael John

    2008-10-01

    When a helicopter crashes or ditches into water the crew and passengers must often make an escape from underwater and a number of the occupants do not survive. This paper examined fatality rates, human factors problems with escape, and causes of death in Canadian civilian registered helicopter accidents in water (1979-2006). Data obtained from the Transportation Safety Board of Canada was reviewed. Key issues such as fatalities, injuries, warning time, sinking, and inversion were examined. There were 46 helicopters that ditched into water. There were 124 crew and passengers involved. Of those, 27 (23%) crew and passengers died. Lack of warning time (55%), rapid sinking (72%), and inversion (35%) were the most common issues in the accidents. Survival rates for Canadian registered helicopter accidents into water (78%) show little change from previously reported worldwide data. Lack of warning time, rapid sinking, and inversion were the significant factors in the survival rate. The practical implication is that crew and passengers involved in planned flights over water must wear all the life support equipment on strap-in and not have it stowed on the back of the seat or in the cabin.

  6. [Retrospective analysis and prevention strategies for accidents associated with cervical manipulation in China].

    PubMed

    Wang, Hui-Hao; Zhan, Hong-Sheng; Zhang, Ming-Cai; Chen, Bo; Guo, Kai

    2012-09-01

    To review previously reported injuries cases which were associated with cervical manipulation in China, and to describe the risks and benefits of the therapy. Relevant case reports, review articles, surveys, and investigations regarding treatment of cervical spondylosis with cervical manipulation involving accidents and associated complication were retrived with a search of the literature from SinoMed, CNKI, CQVIP, and Wanfang digital databases between 1979 to March 2011. The data were extracted and statistically analyzed. Total of 150 cases of injury reported in 40 articles corresponded the inclusion criteria. Accidents occurred in 156 cases,of them,syncope was in 45 cases (28.85%), mild spinal cord injury or compression was in 34 cases (21.79%), nerve root injury was in 24 cases (15.38%), ineffective or symptom increased was in 11 cases (7.05%); cervical spine fracture was in 11 cases (7.05%), dislocation or semiluxation was in 6 cases (3.85%), soft tissue injury was in 3 cases (1.92%), serious accident was 22 cases (14.70%, including paralysis, death and cerebrovascular accident). In cases of serious accident, 12 cases (54.55%) had the other primary diseases. Types of related manipulation including rotation reduction (42.00%, 63 cases), rubbing points or muscle resulting strong stimulation (28.00%, 42 cases). 100 cases (66.67%) obtained cured or basically recovered results, 21 cases (14.00%) improved, 4 cases (2.67%) deterioration and 5 cases (3.33%) died. It is imperative for practitioners to complete the patients' management and assessment before manipulation. That the practitioners conduct a detailed physical examination and make a correct diagnosis would be a pivot method of avoiding accidents. Excluding contraindications and potential risks, standardizing evaluation criteria and practitioners' qualification, increasing safety awareness and risk assessment and strengthening the monitoring of the accidents could decrease the incidence of accidents.

  7. [Traumas in road accidents].

    PubMed

    Picardi, Nicola

    2005-01-01

    Road accidents are nowadays one of the most important cause of injuries, deaths and definitive invalidity, except the war casualties. All the developed countries are affected by this problems, and all the efforts are in progress to make aware the people, mostly the drivers, of all the possible preventive measures. Not all the accident are per se cause of death or invalidity, and there are a lot of evitable deaths and definite morbidity, but an incongruous help can worsen the outcome or menace the final validity and life itself. The injuries affect in different ways the driver and the passenger, and the same safety devices designed to protect the travellers, as safety belts and air bags, can hit them with peculiar mechanisms. A particular attention must be paid to the children, too often transported without the correct safety measures. Very important are the correct steps of the first aid, the succession of the treatment manoeuvres, and the environment were the patients can and must be treated. The Trauma Center represents an ideal solution for the best treatment, but its organization is far from simple, particularly in our country so different in the various regions as population, road, towns and villages distribution, especially in the mountainous districts. Every effort must be done to organize al the best the first, second and definite aid and treatment, together with the active and passive safety devices, and with a correct road education, to stop the true epidemic impact of the road accidents.

  8. Accidents in the greenhouse-construction industry of SE Spain.

    PubMed

    Pérez-Alonso, José; Carreño-Ortega, Angel; Vázquez-Cabrera, Fernando J; Callejón-Ferre, Angel Jesús

    2012-01-01

    This work analyses the labour accidents in the greenhouse-construction industry of SE Spain for the period 1999-2007 through a sample of 180 accident reports. The accidents were characterised by studying 5 variables in order to know the day of the week in which the accident occurred, the hour of the day of the accident, type of accident, the region of Spain in which the accident happened, and the resulting injury. The data characterising the accidents were submitted to a descriptive multiple-correspondence analysis. The incidence of accidents in the greenhouse-construction industry presented a high mean value of 15133.7 per 100,000 workers per year. The days with the greatest incidence of accidents were Thursday and Monday, while the period of greatest number of accidents occurred in the first 4h of the workday. No significant correspondence was found between the day of the week, the hour of the day, or any of the other 3 variables studied. The types of accidents with most frequency were: cuts, punctures, contact with hard or rough material, overexertion, and falls from one level to another. The most affected parts of the anatomy were the eyes, thorax, back, sides, lower legs, and feet. The most common types of injury were bone fractures, twists and sprains, distended muscles, contusions, and being crushed. The study calls attention to the high number of accidents at work, which needs to be corrected by fulfilment of safety regulations at work, on the part of the company. Finally, recommendations are made to correct this situation of high number of accidents at work. Copyright © 2011 Elsevier Ltd and The Ergonomics Society. All rights reserved.

  9. 10 CFR 830.204 - Documented safety analysis.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ..., and accident conditions, including consideration of natural and man-made external events... radioactive and other hazardous materials, and consideration of the need for analysis of accidents which may... preparedness, fire protection, waste management, and radiation protection; and (6) With respect to a nonreactor...

  10. 10 CFR 830.204 - Documented safety analysis.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ..., and accident conditions, including consideration of natural and man-made external events... radioactive and other hazardous materials, and consideration of the need for analysis of accidents which may... preparedness, fire protection, waste management, and radiation protection; and (6) With respect to a nonreactor...

  11. 10 CFR 830.204 - Documented safety analysis.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ..., and accident conditions, including consideration of natural and man-made external events... radioactive and other hazardous materials, and consideration of the need for analysis of accidents which may... preparedness, fire protection, waste management, and radiation protection; and (6) With respect to a nonreactor...

  12. 10 CFR 830.204 - Documented safety analysis.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ..., and accident conditions, including consideration of natural and man-made external events... radioactive and other hazardous materials, and consideration of the need for analysis of accidents which may... preparedness, fire protection, waste management, and radiation protection; and (6) With respect to a nonreactor...

  13. 49 CFR 195.52 - Telephonic notice of certain accidents.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Telephonic notice of certain accidents. 195.52... TRANSPORTATION OF HAZARDOUS LIQUIDS BY PIPELINE Annual, Accident, and Safety-Related Condition Reporting § 195.52 Telephonic notice of certain accidents. (a) At the earliest practicable moment following discovery of a...

  14. [Knowledge and adherence to bio-safety measures and biological accidents by nursing students during their clinical practice].

    PubMed

    Merino-de la Hoz, Felicitas; Durá-Ros, María Jesús; Rodríguez-Martín, Elías; González-Gómez, Silvia; Mariano López-López, Luis; Abajas-Bustillo, Rebeca; de la Horra-Gutiérrez, Inmaculada

    2010-01-01

    To identify the degree of knowledge and performance of bio-safety measures by nursing students and knowing the type of biological accidents suffered during their clinical practice. A cross-sectional study was conducted on the students of three Nursing courses held in May of 2008. Data was collected by an anonymous self-administered questionnaire, with a return of 54%. A total of 97% of students seemed to know the standard biosafety measures, and all of them (100%) stated that those measures must be applied to every patient. However, the reality of clinical practice shows that biosafety measures are only partially applied. An average of 60.2% implement the personal hygiene measures, 66.1% use physical barriers, and 44% use sharp materials safely. Around 32.25% of the students have suffered some biological accident, with a greater incidence in the second year: administering injections (24%), drawing blood samples with Venojet needles (18%) and recapping used needles (17%). The high level of knowledge shown by the students on standard precautions is not always shown in clinical practice. There are significant deficiencies in student safety practices: recapping of used needles continues to be one of the most common risk practices carried out. Copyright (c) 2009 Elsevier España, S.L. All rights reserved.

  15. Examining accident reports involving autonomous vehicles in California

    PubMed Central

    Nader, Nazanin; Eurich, Sky O.; Tripp, Michelle; Varadaraju, Naresh

    2017-01-01

    Autonomous Vehicle technology is quickly expanding its market and has found in Silicon Valley, California, a strong foothold for preliminary testing on public roads. In an effort to promote safety and transparency to consumers, the California Department of Motor Vehicles has mandated that reports of accidents involving autonomous vehicles be drafted and made available to the public. The present work shows an in-depth analysis of the accident reports filed by different manufacturers that are testing autonomous vehicles in California (testing data from September 2014 to March 2017). The data provides important information on autonomous vehicles accidents’ dynamics, related to the most frequent types of collisions and impacts, accident frequencies, and other contributing factors. The study also explores important implications related to future testing and validation of semi-autonomous vehicles, tracing the investigation back to current literature as well as to the current regulatory panorama. PMID:28931022

  16. 77 FR 10666 - Pipeline Safety: Post Accident Drug and Alcohol Testing

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-02-23

    ... operators of Liquefied Natural Gas (LNG) facilities to conduct post- accident drug and alcohol tests of... reviewed, along with other applicable sections of Part 199: Under Sec. 199.105, post-accident drug tests of... administering the test. Covered employees must remain available for post-accident testing, but emergency...

  17. 10 CFR 76.89 - Criticality accident requirements.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 10 Energy 2 2011-01-01 2011-01-01 false Criticality accident requirements. 76.89 Section 76.89 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safety § 76.89 Criticality accident requirements. (a) The Corporation must maintain and operate a criticality monitoring and...

  18. 10 CFR 76.89 - Criticality accident requirements.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 10 Energy 2 2014-01-01 2014-01-01 false Criticality accident requirements. 76.89 Section 76.89 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safety § 76.89 Criticality accident requirements. (a) The Corporation must maintain and operate a criticality monitoring and...

  19. 10 CFR 76.89 - Criticality accident requirements.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 10 Energy 2 2013-01-01 2013-01-01 false Criticality accident requirements. 76.89 Section 76.89 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safety § 76.89 Criticality accident requirements. (a) The Corporation must maintain and operate a criticality monitoring and...

  20. 10 CFR 76.89 - Criticality accident requirements.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 10 Energy 2 2012-01-01 2012-01-01 false Criticality accident requirements. 76.89 Section 76.89 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safety § 76.89 Criticality accident requirements. (a) The Corporation must maintain and operate a criticality monitoring and...

  1. 10 CFR 76.89 - Criticality accident requirements.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Criticality accident requirements. 76.89 Section 76.89 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safety § 76.89 Criticality accident requirements. (a) The Corporation must maintain and operate a criticality monitoring and...

  2. Safety climate and attitude as evaluation measures of organizational safety.

    PubMed

    Isla Díaz, R; Díaz Cabrera, D

    1997-09-01

    The main aim of this research is to develop a set of evaluation measures for safety attitudes and safety climate. Specifically it is intended: (a) to test the instruments; (b) to identify the essential dimensions of the safety climate in the airport ground handling companies; (c) to assess the quality of the differences in the safety climate for each company and its relation to the accident rate; (d) to analyse the relationship between attitudes and safety climate; and (e) to evaluate the influences of situational and personal factors on both safety climate and attitude. The study sample consisted of 166 subjects from three airport companies. Specifically, this research was centered on ground handling departments. The factor analysis of the safety climate instrument resulted in six factors which explained 69.8% of the total variance. We found significant differences in safety attitudes and climate in relation to type of enterprise.

  3. A human factors analysis of fatal and serious injury accidents in Alaska, 2004-2009.

    DOT National Transportation Integrated Search

    2011-12-01

    "This report summarizes the analysis of 97 general aviation accidents in Alaska that resulted in a fatality or serious : injury to one or more aircraft occupants for the years 2004-2009. The accidents were analyzed using the Human : Factors Analysis ...

  4. 41 CFR 102-80.110 - What must an equivalent level of safety analysis indicate?

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ..., and reliability of all building systems impacting fire growth, occupant knowledge of the fire, and... Management Federal Property Management Regulations System (Continued) FEDERAL MANAGEMENT REGULATION REAL PROPERTY 80-SAFETY AND ENVIRONMENTAL MANAGEMENT Accident and Fire Prevention Equivalent Level of Safety...

  5. 41 CFR 102-80.110 - What must an equivalent level of safety analysis indicate?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ..., and reliability of all building systems impacting fire growth, occupant knowledge of the fire, and... Management Federal Property Management Regulations System (Continued) FEDERAL MANAGEMENT REGULATION REAL PROPERTY 80-SAFETY AND ENVIRONMENTAL MANAGEMENT Accident and Fire Prevention Equivalent Level of Safety...

  6. 41 CFR 102-80.110 - What must an equivalent level of safety analysis indicate?

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ..., and reliability of all building systems impacting fire growth, occupant knowledge of the fire, and... Management Federal Property Management Regulations System (Continued) FEDERAL MANAGEMENT REGULATION REAL PROPERTY 80-SAFETY AND ENVIRONMENTAL MANAGEMENT Accident and Fire Prevention Equivalent Level of Safety...

  7. 41 CFR 102-80.110 - What must an equivalent level of safety analysis indicate?

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ..., and reliability of all building systems impacting fire growth, occupant knowledge of the fire, and... Management Federal Property Management Regulations System (Continued) FEDERAL MANAGEMENT REGULATION REAL PROPERTY 80-SAFETY AND ENVIRONMENTAL MANAGEMENT Accident and Fire Prevention Equivalent Level of Safety...

  8. Occupational safety management: the role of causal attribution.

    PubMed

    Gyekye, Seth Ayim

    2010-12-01

    The paper addresses the causal attribution theory, an old and well-established theme in social psychology which denotes the everyday, commonsense explanations that people use to explain events and the world around them. The attribution paradigm is considered one of the most appropriate analytical tools for exploratory and descriptive studies in social psychology and organizational literature. It affords the possibility of describing accident processes as objectively as possible and with as much detail as possible. Causal explanations are vital to the formal analysis of workplace hazards and accidents, as they determine how organizations act to prevent accident recurrence. Accordingly, they are regarded as fundamental and prerequisite elements for safety management policies. The paper focuses primarily on the role of causal attributions in occupational and industrial accident analyses and implementation of safety interventions. It thus serves as a review of the contribution of attribution theory to occupational and industrial accidents. It comprises six sections. The first section presents an introduction to the classic attribution theories, and the second an account of the various ways in which the attribution paradigm has been applied in organizational settings. The third and fourth sections review the literature on causal attributions and demographic and organizational variables respectively. The sources of attributional biases in social psychology and how they manifest and are identified in the causal explanations for industrial and occupational accidents are treated in the fifth section. Finally, conclusion and recommendations are presented. The recommendations are particularly important for the reduction of workplace accidents and associated costs. The paper touches on the need for unbiased causal analyses, belief in the preventability of accidents, and the imperative role of management in occupational safety management.

  9. Drivers of accident preparedness and safety: evidence from the RMP Rule.

    PubMed

    Kleindorfer, Paul R; Elliott, Michael R; Wang, Yanlin; Lowe, Robert A

    2004-11-11

    This paper provides an overview of recent results derived from the accident history data collected under 112(r) of the Clean Air Act Amendments (the Risk Management Program (RMP) Rule) covering the period 1994-2000, together with a preliminary assessment of the effectiveness of the RMP Rule as a form of Management System Regulation. These were undertaken at the University of Pennsylvania by a multi-disciplinary team of economists, statisticians and epidemiologists with the support of the US Environmental Protection Agency and its Office of Emergency Prevention, Preparedness and Response (OEPPR, formerly CEPPO). Section 112(r) of the Clean Air Act Amendments of 1990 requires that chemical facilities in the US that had on premises more than specified quantities of toxic or flammable chemicals file a 5-year history of accidents. The initial data reported under the RMP Rule covered roughly the period from mid-1994 through mid-2000, and provided details on economic, environmental and acute health affects resulting from accidents at some 15,000 US chemical facilities for this period. This paper reviews research based on this data. The research is in the form of a retrospective cohort study that considers the statistical associations between accident frequency and accident severity at covered facilities (the outcome variables of interest) and a number of facility characteristics (the available predictor variables provided by the RMP Rule), the latter including such facility characteristics as size, hazardousness, financial characteristics of parent company-owners of the facility, regulatory programs in force at the facility, and host community characteristics for the surrounding county in which the facility was located, as captured in the 1990 Census. Among the findings reviewed are: (1) positive associations with (a measure of) facility hazardousness and accident, injury and economic costs of accidents; (2) positive (resp., negative) associations between accident

  10. Alternative method of highway traffic safety analysis for developing countries using delphi technique and Bayesian network.

    PubMed

    Mbakwe, Anthony C; Saka, Anthony A; Choi, Keechoo; Lee, Young-Jae

    2016-08-01

    Highway traffic accidents all over the world result in more than 1.3 million fatalities annually. An alarming number of these fatalities occurs in developing countries. There are many risk factors that are associated with frequent accidents, heavy loss of lives, and property damage in developing countries. Unfortunately, poor record keeping practices are very difficult obstacle to overcome in striving to obtain a near accurate casualty and safety data. In light of the fact that there are numerous accident causes, any attempts to curb the escalating death and injury rates in developing countries must include the identification of the primary accident causes. This paper, therefore, seeks to show that the Delphi Technique is a suitable alternative method that can be exploited in generating highway traffic accident data through which the major accident causes can be identified. In order to authenticate the technique used, Korea, a country that underwent similar problems when it was in its early stages of development in addition to the availability of excellent highway safety records in its database, is chosen and utilized for this purpose. Validation of the methodology confirms the technique is suitable for application in developing countries. Furthermore, the Delphi Technique, in combination with the Bayesian Network Model, is utilized in modeling highway traffic accidents and forecasting accident rates in the countries of research. Copyright © 2016 Elsevier Ltd. All rights reserved.

  11. Quality evaluation of official accident reports conducted by Labour Authorities in Andalusia (Spain).

    PubMed

    Salguero-Caparros, Francisco; Suarez-Cebador, Manuel; Carrillo-Castrillo, Jesús A; Rubio-Romero, Juan Carlos

    2018-01-01

    A public accident investigation is carried out when the consequences of the incident are significant or the accident has occurred in unusual circumstances. We evaluated the quality of the official accident investigations being conducted by Safety Specialists of the Labour Authorities in Andalusia. To achieve this objective, we analysed 98 occupational accident investigations conducted by the Labour Authorities in Andalusia in the last quarter of 2014. Various phases in the accident investigation process were examined, such as the use of the Eurostat variables within European Statistics on Accidents at Work (ESAW), detection of causes, determination of preventive measures, cost analysis of the accidents, identification of noncompliance with legal requirements or the investigation method used. The results of this study show that 77% of the official occupational accident investigation reports analysed were conducted in accordance with all the quality criteria recommended in the literature. To enhance glogal learning, and optimize allocation of resources, we propose the development of a harmonized European model for the public investigation of occupational accidents. Further it would be advisable to create a common classification and coding system for the causes of accidents for all European Union Member States.

  12. Analysis of occupational accidents with biological material among professionals in pre-hospital services.

    PubMed

    de Oliveira, Adriana Cristina; Paiva, Maria Henriqueta Rocha Siqueira

    2013-02-01

    To estimate the prevalence of accidents due to biological material exposure, the characteristics and post-accident conduct among professionals of pre-hospital services of the four municipalities of Minas Gerais, Brazil. A cross-sectional study, using a structured questionnaire that was developed to enable the calculation of prevalence, descriptive analysis and analytical analysis using logistic regression. The study included 228 professionals; the prevalence of accidents due to biological material exposure was 29.4%, with 49.2% percutaneous, 10.4% mucousal, 6.0% non-intact skin, and 34.4% intact skin. Among the professionals injured, those that stood out were nursing technicians (41.9%) and drivers (28.3%). Notification of the occurrence of the accident occurred in 29.8% of the cases. Percutaneous exposure was associated with time of work in the organization (OR=2.51, 95% CI: 1.18 to 5.35, p<0.017). Notification about accidents with biological material should be encouraged, along with professional evaluation/monitoring.

  13. 36 CFR 4.4 - Report of motor vehicle accident.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... accident. 4.4 Section 4.4 Parks, Forests, and Public Property NATIONAL PARK SERVICE, DEPARTMENT OF THE INTERIOR VEHICLES AND TRAFFIC SAFETY § 4.4 Report of motor vehicle accident. (a) The operator of a motor vehicle involved in an accident resulting in property damage, personal injury or death shall report the...

  14. 36 CFR 4.4 - Report of motor vehicle accident.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... accident. 4.4 Section 4.4 Parks, Forests, and Public Property NATIONAL PARK SERVICE, DEPARTMENT OF THE INTERIOR VEHICLES AND TRAFFIC SAFETY § 4.4 Report of motor vehicle accident. (a) The operator of a motor vehicle involved in an accident resulting in property damage, personal injury or death shall report the...

  15. Time to death analysis of road traffic accidents in relation to delta V, drunk driving, and restraint systems.

    PubMed

    Ju, Yonghan; Sohn, So Young

    2014-01-01

    The main goal of this research is to identify variables related to the expected time to death due to road traffic accidents (RTAs). Such research is expected to be useful in improving safety laws and regulations and developing new safety systems. The resulting information is crucial not only for reducing accident fatalities but for assessing related insurance policies. In this article, we analyze factors that are potentially associated with variation in the expected survival time after a road traffic accident using Weibull regression. In particular, we consider the association with alcohol involvement, delta V, and restraint systems. Our empirical results, obtained based on the NASS-CDS, indicate that the expected survival time for non-alcohol-impaired drivers is 3.23 times longer at a delta V of 50 km/h than that for alcohol-impaired drivers under the same conditions. In addition, it was observed that, even when occupants were alcohol-impaired, if they were protected by both air bags and seat belts, their expected survival time after an RTA increased 2.59-fold compared to alcohol-impaired drivers who used only seat belts. Our findings may be useful in improving road traffic safety and insurance policies by offering insights into the factors that reduce fatalities.

  16. Predicting and analyzing the trend of traffic accidents deaths in Iran in 2014 and 2015

    PubMed Central

    Mehmandar, Mohammadreza; Soori, Hamid; Mehrabi, Yadolah

    2016-01-01

    Background: Predicting the trend in traffic accidents deaths and its analysis can be a useful tool for planning and policy-making, conducting interventions appropriate with death trend, and taking the necessary actions required for controlling and preventing future occurrences. Objective: Predicting and analyzing the trend of traffic accidents deaths in Iran in 2014 and 2015. Settings and Design: It was a cross-sectional study. Materials and Methods: All the information related to fatal traffic accidents available in the database of Iran Legal Medicine Organization from 2004 to the end of 2013 were used to determine the change points (multi-variable time series analysis). Using autoregressive integrated moving average (ARIMA) model, traffic accidents death rates were predicted for 2014 and 2015, and a comparison was made between this rate and the predicted value in order to determine the efficiency of the model. Results: From the results, the actual death rate in 2014 was almost similar to that recorded for this year, while in 2015 there was a decrease compared with the previous year (2014) for all the months. A maximum value of 41% was also predicted for the months of January and February, 2015. Conclusion: From the prediction and analysis of the death trends, proper application and continuous use of the intervention conducted in the previous years for road safety improvement, motor vehicle safety improvement, particularly training and culture-fostering interventions, as well as approval and execution of deterrent regulations for changing the organizational behaviors, can significantly decrease the loss caused by traffic accidents. PMID:27308255

  17. An Examination of Safety Management Systems and Aviation Technologies in the Helicopter Emergency Medical Services Industry

    NASA Astrophysics Data System (ADS)

    Buckner, Steven A.

    The Helicopter Emergency Medical Service (HEMS) industry has a significant role in the transportation of injured patients, but has experienced more accidents than all other segments of the aviation industry combined. With the objective of addressing this discrepancy, this study assesses the effect of safety management systems implementation and aviation technologies utilization on the reduction of HEMS accident rates. Participating were 147 pilots from Federal Aviation Regulations Part 135 HEMS operators, who completed a survey questionnaire based on the Safety Culture and Safety Management System Survey (SCSMSS). The study assessed the predictor value of SMS implementation and aviation technologies to the frequency of HEMS accident rates with correlation and multiple linear regression. The correlation analysis identified three significant positive relationships. HEMS years of experience had a high significant positive relationship with accident rate (r=.90; p<.05); SMS had a moderate significant positive relationship to Night Vision Goggles (NVG) (r=.38; p<.05); and SMS had a slight significant positive relationship with Terrain Avoidance Warning System (TAWS) (r=.234; p<.05). Multiple regression analysis suggested that when combined with NVG, TAWS, and SMS, HEMS years of experience explained 81.4% of the variance in accident rate scores (p<.05), and HEMS years of experience was found to be a significant predictor of accident rates (p<.05). Additional quantitative regression analysis was recommended to replicate the results of this study and to consider the influence of these variables for continued reduction of HEMS accidents, and to induce execution of SMS and aviation technologies from a systems engineering application. Recommendations for practice included the adoption of existing regulatory guidance for a SMS program. A qualitative analysis was also recommended for future study SMS implementation and HEMS accident rate from the pilot's perspective. A

  18. Interim MELCOR Simulation of the Fukushima Daiichi Unit 2 Accident Reactor Core Isolation Cooling Operation

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Ross, Kyle W.; Gauntt, Randall O.; Cardoni, Jeffrey N.

    2013-11-01

    Data, a brief description of key boundary conditions, and results of Sandia National Laboratories’ ongoing MELCOR analysis of the Fukushima Unit 2 accident are given for the reactor core isolation cooling (RCIC) system. Important assumptions and related boundary conditions in the current analysis additional to or different than what was assumed/imposed in the work of SAND2012-6173 are identified. This work is for the U.S. Department of Energy’s Nuclear Energy University Programs fiscal year 2014 Reactor Safety Technologies Research and Development Program RC-7: RCIC Performance under Severe Accident Conditions.

  19. The Human Factors of an Early Space Accident: Flight 3-65 of the X-15

    NASA Technical Reports Server (NTRS)

    Barshi, Immanuel; Statler, Irving C.; Orr, Jeb S.

    2015-01-01

    The X-15 was a critical research vehicle in the early days of space flight. On November 15, 1967, the X-15-3 suffered an in-flight breakup. This 191st flight of the X-15 and the 65th flight of this third configuration was the only fatal accident of the X-15 program. This paper presents an analysis, from a human factors perspective, of the events that led up to the accident. The analysis is based on the information contained in the report of the Air Force-NASA Accident Investigation Board (AIB) dated January, 1968. The AIBs analysis addressed, primarily, the events that occurred subsequent to the pilots taking direct control of the reaction control system. The analysis described here suggests that all of the events that caused the accident occurred well before the moment when the pilot switched to direct control. Consequently, the analyses and conclusions regarding the causal factors of, and the contributing factors to, the loss of Flight 3-65 presented here differ from those of the AIB based on the same evidence. Although the accident occurred in 1967, the results of the presented analysis are still relevant today. We present our analysis and discuss its implications for the safety of space operations.

  20. The Human Factors of an Early Space Accident: Flight 3-65 of the X-15

    NASA Technical Reports Server (NTRS)

    Barshi, Immanuel; Statler, Irving C.; Orr, Jeb S.

    2016-01-01

    The X-15 was a critical research vehicle in the early days of space flight. On November 15, 1967, the X-15-3 suffered an in-flight breakup. This 191st flight of the X-15 and the 65th flight of this third configuration was the only fatal accident of the X-15 program. This paper presents an analysis, from a human factors perspective, of the events that led up to the accident. The analysis is based on the information contained in the report of the Air Force-NASA Accident Investigation Board (AIB) dated January, 1968. The AIBs analysis addressed, primarily, the events that occurred subsequent to the pilot's taking direct control of the reaction control system. The analysis described here suggests that, rather than events following the pilot's switch to direct control, it was the events preceding the switch that led to the accident. Consequently, the analyses and conclusions regarding the causal factors of, and the contributing factors to, the loss of Flight 3-65 presented here differ from those of the AIB based on the same evidence. Although the accident occurred in 1967, the results of the presented analysis are still relevant today. We present our analysis and discuss its implications for the safety of space operations.

  1. 41 CFR 102-80.110 - What must an equivalent level of safety analysis indicate?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false What must an equivalent... Management Federal Property Management Regulations System (Continued) FEDERAL MANAGEMENT REGULATION REAL PROPERTY 80-SAFETY AND ENVIRONMENTAL MANAGEMENT Accident and Fire Prevention Equivalent Level of Safety...

  2. Railroad safety statistics annual report 1999

    DOT National Transportation Integrated Search

    2000-08-01

    This edition of the Railroad Safety Statistics compiles previous safety bulletins prepared by the Federal Railroad Administration (FRA). These include: the Accident/Incident Bulletin; the Highway-Rail Crossing Accident/Incident and Inventory Bulletin...

  3. Railroad safety statistics annual report 2005

    DOT National Transportation Integrated Search

    2006-12-01

    This edition of the Railroad Safety Statistics compiles previous safety bulletins prepared by the Federal Railroad Administration (FRA). These include: the Accident/Incident Bulletin; the Highway-Rail Crossing Accident/Incident And Inventory Bulletin...

  4. Railroad safety statistics annual report 2003

    DOT National Transportation Integrated Search

    2005-10-01

    This edition of the Railroad Safety Statistics compiles previous safety bulletins prepared by the Federal Railroad Administration (FRA). These include: the Accident/Incident Bulletin; the Highway-Rail Crossing Accident/Incident And Inventory Bulletin...

  5. Railroad safety statistics annual report 2004

    DOT National Transportation Integrated Search

    2005-11-01

    This edition of the Railroad Safety Statistics compiles previous safety bulletins prepared by the Federal Railroad Administration (FRA). These include: the Accident/Incident Bulletin; the Highway-Rail Crossing Accident/Incident And Inventory Bulletin...

  6. Railroad safety statistics annual report 2000

    DOT National Transportation Integrated Search

    2001-07-01

    This edition of the Railroad Safety Statistics compiles previous safety bulletins prepared by the : Federal Railroad Administration (FRA). These include: the Accident/Incident Bulletin; the : Highway-Rail Crossing Accident/Incident And Inventory Bull...

  7. Analysis of unmitigated large break loss of coolant accidents using MELCOR code

    NASA Astrophysics Data System (ADS)

    Pescarini, M.; Mascari, F.; Mostacci, D.; De Rosa, F.; Lombardo, C.; Giannetti, F.

    2017-11-01

    In the framework of severe accident research activity developed by ENEA, a MELCOR nodalization of a generic Pressurized Water Reactor of 900 MWe has been developed. The aim of this paper is to present the analysis of MELCOR code calculations concerning two independent unmitigated large break loss of coolant accident transients, occurring in the cited type of reactor. In particular, the analysis and comparison between the transients initiated by an unmitigated double-ended cold leg rupture and an unmitigated double-ended hot leg rupture in the loop 1 of the primary cooling system is presented herein. This activity has been performed focusing specifically on the in-vessel phenomenology that characterizes this kind of accidents. The analysis of the thermal-hydraulic transient phenomena and the core degradation phenomena is therefore here presented. The analysis of the calculated data shows the capability of the code to reproduce the phenomena typical of these transients and permits their phenomenological study. A first sequence of main events is here presented and shows that the cold leg break transient results faster than the hot leg break transient because of the position of the break. Further analyses are in progress to quantitatively assess the results of the code nodalization for accident management strategy definition and fission product source term evaluation.

  8. Nuclear safety

    NASA Technical Reports Server (NTRS)

    Buden, D.

    1991-01-01

    Topics dealing with nuclear safety are addressed which include the following: general safety requirements; safety design requirements; terrestrial safety; SP-100 Flight System key safety requirements; potential mission accidents and hazards; key safety features; ground operations; launch operations; flight operations; disposal; safety concerns; licensing; the nuclear engine for rocket vehicle application (NERVA) design philosophy; the NERVA flight safety program; and the NERVA safety plan.

  9. Comprehensive Analysis of Two Downburst-Related Aircraft Accidents

    NASA Technical Reports Server (NTRS)

    Shen, J.; Parks, E. K.; Bach, R. E.

    1996-01-01

    Although downbursts have been identified as the major cause of a number of aircraft takeoff and landing accidents, only the 1985 Dallas/Fort Worth (DFW) and the more recent (July 1994) Charlotte, North Carolina, landing accidents provided sufficient onboard recorded data to perform a comprehensive analysis of the downburst phenomenon. The first step in the present analysis was the determination of the downburst wind components. Once the wind components and their gradients were determined, the degrading effect of the wind environment on the airplane's performance was calculated. This wind-shear-induced aircraft performance degradation, sometimes called the F-factor, was broken down into two components F(sub 1) and F(sub 2), representing the effect of the horizontal wind gradient and the vertical wind velocity, respectively. In both the DFW and Charlotte cases, F(sub 1) was found to be the dominant causal factor of the accident. Next, the aircraft in the two cases were mathematically modeled using the longitudinal equations of motion and the appropriate aerodynamic parameters. Based on the aircraft model and the determined winds, the aircraft response to the recorded pilot inputs showed good agreement with the onboard recordings. Finally, various landing abort strategies were studied. It was concluded that the most acceptable landing abort strategy from both an analytical and pilot's standpoint was to hold constant nose-up pitch attitude while operating at maximum engine thrust.

  10. A spatial analysis of urban transit accidents assisted by Emergency Mobile Care Services: an analysis of space and time.

    PubMed

    Mendonça, Marcela Franklin Salvador de; Silva, Amanda Priscila de Santana Cabral; Castro, Claudia Cristina Lima de

    2017-01-01

    Urban transit accident are a global public health problem. The objective of this study was to describe the profile of the victims and the occurrences of urban transit accidents attended to by emergency mobile care services (Serviço de Atendimento Móvel de Urgência- SAMU) in Recife, and their distribution based on spatial analysis. An ecological study, developed through secondary data from emergency mobile care services in Recife, referring to the total number of occurrences of urban transit accidents attended to from January 1 to June 30, 2015. The spatial analysis was performed using the Moran index. Basic support units performed most of the emergency services (89.2%). Among the victims, there was a predominance of males (76.8%) and an age group of 20 - 29 years old (31.5%). Collisions were responsible for 59.9% of the transit accidents, and motorcycles for 61.6% of the accidents among all means of transportation. Friday was the day that showed the highest risk for treatment, and there was a concentration of events between 6:00 am - 8:59am and 6:00pm - 8:59pm. The MoranMap identified critical areas where calls came from traffic accidents during the period analyzed. The records of the mobile service from the spatial analysis are an important source of information for health surveillance. The spatial analysis of urban transit accidents identified regions with a positive spatial correlation, providing subsidies to the logistical planning of emergency mobile care services. This study is groundbreaking in that it offers such information about the region.

  11. Safety Management Information Statistics (SAMIS) - 1995 Annual Report

    DOT National Transportation Integrated Search

    1997-04-01

    The Safety Management Information Statistics 1995 Annual Report is a compilation and analysis of transit accident, casualty and crime statistics reported under the Federal Transit Administration's National Transit Database Reporting by transit system...

  12. Workability of Safety Education and Training for Workers' Strategy in Accident Reduction in Selected Manufacturing Industries in Lagos State

    ERIC Educational Resources Information Center

    Ayodele, Rachael B.; Olubayo-Fatiregun, Martina A.

    2013-01-01

    This study determined the workability of Safety Education and Training for Workers' strategy in reducing accidents. A descriptive survey research design was used. A total of 20 Managerial staff with mean work experience of 13.5 years was selected from 10 manufacturing industries in Lagos State, using intact group method. They were 100% males. Data…

  13. Railroad safety statistics annual report 1998

    DOT National Transportation Integrated Search

    1999-07-01

    This edition of the Railroad Safety Statistics is a composite of previous safety bulletins prepared by the Federal Railroad Administration (FRA). These include: the Accident/Incident Bulletin; the Highway-Rail Crossing Accident/Incident And Inventory...

  14. An Updated Examination of Aviation Accidents Associated with Turbulence, Wind Shear and Thunderstorm

    NASA Technical Reports Server (NTRS)

    Evans, Joni K.

    2014-01-01

    One of the technical challenges within the Atmospheric Environment Safety Technologies (AEST) Project of the Aviation Safety Program was to "improve and expand remote sensing and mitigation of hazardous atmospheric environments and phenomena"1. In 2012, the author performed an analysis comparing various characteristics of accidents associated with different types of atmospheric hazard environments2. This document reports an update to that analysis which was done in preparation for presenting these findings at the 2015 annual meeting of the Transportation Research Board. Specifically, an additional three years of data were available, and a time-trend analysis was added.

  15. Severity of electrical accidents in the construction industry in Spain.

    PubMed

    Suárez-Cebador, Manuel; Rubio-Romero, Juan Carlos; López-Arquillos, Antonio

    2014-02-01

    This paper analyzes the severity of workplace accidents involving electricity in the Spanish construction sector comprising 2,776 accidents from 2003 to 2008. The investigation considered the impact of 13 variables, classified into 5 categories: Personal, Business, Temporal, Material, and Spatial. The findings showed that electrical accidents are almost five times more likely to have serious consequences than the average accident in the sector and it also showed how the variables of age, occupation, company size, length of service, preventive measures, time of day, days of absence, physical activity, material agent, type of injury, body part injured, accident location, and type of location are related to the severity of the electrical accidents under consideration. The present situation makes it clear that greater effort needs to be made in training, monitoring, and signage to guarantee a safe working environment in relation to electrical hazards. This research enables safety technicians, companies, and government officials to identify priorities and to design training strategies to minimize the serious consequences of electrical accidents for construction workers. Copyright © 2013 Elsevier Ltd and National Safety Council. All rights reserved.

  16. Road accidents caused by sleepy drivers: Update of a Norwegian survey.

    PubMed

    Phillips, Ross Owen; Sagberg, Fridulv

    2013-01-01

    The current study tests, updates and expands a model of factors associated with sleepy driving, originally based on a 1997 survey of accident-involved Norwegian drivers (Sagberg, F., 1999. Road accidents caused by drivers falling asleep. Accident Analysis & Prevention 31, 639-649). The aim is to establish a robust model to inform measures to tackle sleepy driving. The original questions on (i) tiredness-related accidents and (ii) incidents of sleep behind the wheel in the last 12 months were again posed in 2003 and 2008, in independent surveys of Norwegian drivers involved in accidents reported to a large insurance company. According to those drivers at-fault for the accident, tiredness or sleepiness behind the wheel contributed to between 1.9 and 3.9 per cent of all types of accident reported to the insurance company across these years. Accident-involved drivers not at fault for the accident reported a reduction in the incidence of sleep behind the wheel for the preceding year, decreasing from 8.3 per cent in 1997 to 2.9 per cent in 2008. The reasons for this are not clear. According to logistic regression analysis of survey responses, the following factors were robustly associated with road accidents involving sleepy driving: driving off the road; good road conditions; longer distance driven since the start of the trip; and fewer years with a driving licence. The following factors are consistently associated with reports of sleep behind the wheel, whether or not it leads to an accident: being male; driving further per year; being younger; and having sleep-related health problems. Taken together these findings suggest that young, inexperienced male drivers who drive long distances may be a suitable target for road safety campaigns aimed at tackling sleepy driving. Copyright © 2012 Elsevier Ltd. All rights reserved.

  17. Method for Assessing Risk of Road Accidents in Transportation of School Children

    NASA Astrophysics Data System (ADS)

    Pogotovkina, N. S.; Volodkin, P. P.; Demakhina, E. S.

    2017-11-01

    The rationale behind the problem being investigated is explained by the remaining high level of the accident rates with the participation of vehicles carrying groups of children, including school buses, in the Russian Federation over the period of several years. The article is aimed at the identification of new approaches to improve the safety of transportation of schoolchildren in accordance with the Concept of children transportation by buses and the plan for its implementation. The leading approach to solve the problem under consideration is the prediction of accidents in the schoolchildren transportation. The article presents the results of the accident rate analysis with the participation of school buses in the Russian Federation for five years. Besides, a system to monitor the transportation of schoolchildren is proposed; the system will allow analyzing and forecasting traffic accidents which involve buses carrying groups of children, including school buses. In addition, the article presents a methodology for assessing the risk of road accidents during the transportation of schoolchildren.

  18. Safety Management Information Statistics (SAMIS) - 1993 Annual Report

    DOT National Transportation Integrated Search

    1995-05-01

    The 1993 Safety Management Information Statistics (SAMIS) report, now in its fourth year of publication, is a compilation and analysis of transit accident and casualty statistics uniformly collected from approximately 400 transit agencies throughout ...

  19. Wet weather highway accident analysis and skid resistance data management system (volume II : user's manual).

    DOT National Transportation Integrated Search

    1992-06-01

    The objectives and scope of this research are to establish an effective methodology for wet weather accident analysis and to develop a database management system to facilitate information processing and storage for the accident analysis process, skid...

  20. How perceptions of experience-based analysis influence explanations of work accidents.

    PubMed

    Mbaye, Safiétou; Kouabenan, Dongo Rémi

    2013-12-01

    This article looks into how perceptions of experience-based analysis (EBA) influence causal explanations of accidents given by managers and workers in the chemical industry (n=409) and in the nuclear industry (n=222). The approach is based on the model of naive explanations of accidents (Kouabenan, 1999, 2006, 2009), which recommends taking into account explanations of accidents spontaneously given by individuals, including laypersons, not only to better understand why accidents occur but also to design and implement the most appropriate prevention measures. The study reported here describes the impact of perceptions about EBA (perceived effectiveness, personal commitment, and the feeling of being involved in EBA practices) on managers' and workers' explanations of accidents likely to occur at the workplace. The results indicated that both managers and workers made more internal explanations than external ones when they perceived EBA positively. Moreover, the more the participants felt involved in EBA, were committed to it, and judged it effective, the more they explained accidents in terms of factors internal to the workers. Recommendations are proposed for reducing defensive reactions, increasing personal commitment to EBA, and improving EBA effectiveness. © 2013.

  1. Alcohol-related road traffic accidents before and after the passing of the Road Traffic Safety Act in Croatia.

    PubMed

    Missoni, Eduard; Bozić, Boris; Missoni, Ivan

    2012-12-01

    The aim of this study was to gather enough data in order to formulate theory- and research-based recommendations to policy makers with the intention of decreasing the number of alcohol-related accidents and victims on Croatian roads. The data on the injured traffic participants and the share of participants under the influence of alcohol were collected from the police reports of the Traffic Police Department, Ministry of the Interior, written at the scene of the respective accidents. This documentation was then processed by descriptive epidemiology and analysed through a four-year period, before and after the passing of the New Road Traffic Safety Act in the Republic of Croatia, on 20 August 2004. In the first six months of 2005, after the passing of the Act, there were 3,275 accidents caused by the motorists under the influence of alcohol (12.5% of all the accidents), with 64 persons killed. Only 5 fatalities (8%) were caused by the drivers with measured blood alcohol concentration of up to 0.5 per thousand. As much as 27 fatalities (42%) were caused by the drivers with measured more than 1.5 per thousand, while half of the fatalities, 32 (50%), were caused by drivers with 0.5-1.5 per thousand. In this period, more than 451,000 violations were recorded, whereas in the same period of the previous year, the number of violations was about 519,000. A reduction of the total number of accidents is the result of the new regulation provision, according to which the incidents without human victims do not have to be reported to the police. The number of traffic accidents caused by drivers under the influence of alcohol had increased by some dozen per cents, namely: 2005 - 6,219 persons, 2006- 6,590 persons, noting that in 2006 one less person was killed (123) compared to 2005. In 2005, drivers with alcohol concentration of 0-0.5 per thousand caused 1,096 accidents, with 14 fatalities, whereas in 2006 there were 1,164 accidents with 9 fatalities. A total of 2,314 accidents

  2. A new approach to modeling aviation accidents

    NASA Astrophysics Data System (ADS)

    Rao, Arjun Harsha

    General Aviation (GA) is a catchall term for all aircraft operations in the US that are not categorized as commercial operations or military flights. GA aircraft account for almost 97% of the US civil aviation fleet. Unfortunately, GA flights have a much higher fatal accident rate than commercial operations. Recent estimates by the Federal Aviation Administration (FAA) showed that the GA fatal accident rate has remained relatively unchanged between 2010 and 2015, with 1566 fatal accidents accounting for 2650 fatalities. Several research efforts have been directed towards betters understanding the causes of GA accidents. Many of these efforts use National Transportation Safety Board (NTSB) accident reports and data. Unfortunately, while these studies easily identify the top types of accidents (e.g., inflight loss of control (LOC)), they usually cannot identify why these accidents are happening. Most NTSB narrative reports for GA accidents are very short (many are only one paragraph long), and do not contain much information on the causes (likely because the causes were not fully identified). NTSB investigators also code each accident using an event-based coding system, which should facilitate identification of patterns and trends in causation, given the high number of GA accidents each year. However, this system is susceptible to investigator interpretation and error, meaning that two investigators may code the same accident differently, or omit applicable codes. To facilitate a potentially better understanding of GA accident causation, this research develops a state-based approach to check for logical gaps or omissions in NTSB accident records, and potentially fills-in the omissions. The state-based approach offers more flexibility as it moves away from the conventional event-based representation of accidents, which classifies events in accidents into several categories such as causes, contributing factors, findings, occurrences, and phase of flight. The method

  3. An Examination of Commercial Motor Vehicle Hours of Service Safety Regulation

    DTIC Science & Technology

    2016-09-01

    enough data for a statistical analysis of its effects on truck driver safety. This research found that by comparing truck driving safety data prior...impact on the commercial motor vehicle industry. Research has demonstrated how fatigue leads to increased accident rates by decreasing reaction time

  4. Rotorcraft Drivetrain Life Safety and Reliability (Cycle de Vie, Securite et Fiabilite des Chaines Dynamiques des Avions a Voilure Tournante)

    DTIC Science & Technology

    1990-06-01

    design and component technologies are reviewed against a background of accident data analysis , resulting in grounds for confidence in higher safety levels...constructors or operators taking voluntary actions based on accident investigations and their own data . Analysis of the CAA Summaty data (Appendix 3...of engines. In the accident data analysis in Appendix 3, insufficient data was available to determine whether rotor configuration or associated

  5. The situation of hazardous chemical accidents in China between 2000 and 2006.

    PubMed

    Duan, Weili; Chen, Guohua; Ye, Qing; Chen, Qingguang

    2011-02-28

    From the aspects of the total quantity of accidents, regional inequality, enterprises scale and environmental pollution accidents, this study makes an analysis of hazardous chemical accidents in China for the period spanning from 2000 to 2006. The following results are obtained: firstly, there were lots of accidents and fatalities in hazardous chemical business, i.e., the number of casualty accidents fluctuated between 200 and 600/year, the number of fatality fluctuated between 220 and 1100/year. Secondly, the accident rate in developed southeast coastal areas, e.g., Guangdong, Zhejiang and Jiangsu, was far higher than that in the northwest regions, e.g., Xizang, Xinjiang, and Qinghai. Thirdly, nearly 80% of dangerous chemical accidents had occurred in small and medium-sized enterprises (SMEs). Finally, various sudden environmental pollution accidents resulted from hazardous chemicals were frequent in recent years, causing a huge damage to human and property. Then, based on the readjustment of economic structure in the last decades, the development status of Occupational Health and Safety (OHS) in SMEs and other factors, the paper explores the main causes, which offers valuable insight into measures that should be taken to reduce hazardous chemical accidents. Copyright © 2010 Elsevier B.V. All rights reserved.

  6. Do failures in non-technical skills contribute to fatal medical accidents in Japan? A review of the 2010-2013 national accident reports.

    PubMed

    Uramatsu, Masashi; Fujisawa, Yoshikazu; Mizuno, Shinya; Souma, Takahiro; Komatsubara, Akinori; Miki, Tamotsu

    2017-02-16

    We sought to clarify how large a proportion of fatal medical accidents can be considered to be caused by poor non-technical skills, and to support development of a policy to reduce number of such accidents by making recommendations about possible training requirements. Summaries of reports of fatal medical accidents, published by the Japan Medical Safety Research Organization, were reviewed individually. Three experienced clinicians and one patient safety expert conducted the reviews to determine the cause of death. Views of the patient safety expert were given additional weight in the overall determination. A total of 73 summary reports of fatal medical accidents were reviewed. These reports had been submitted by healthcare organisations across Japan to the Japan Medical Safety Research Organization between April 2010 and March 2013. The cause of death in fatal medical accidents, categorised into technical skills, non-technical skills and inevitable progress of disease were evaluated. Non-technical skills were further subdivided into situation awareness, decision making, communication, team working, leadership, managing stress and coping with fatigue. Overall, the cause of death was identified as non-technical skills in 34 cases (46.6%), disease progression in 33 cases (45.2%) and technical skills in two cases (5.5%). In two cases, no consensual determination could be achieved. Further categorisation of cases of non-technical skills were identified as 14 cases (41.2%) of problems with situation awareness, eight (23.5%) with team working and three (8.8%) with decision making. These three subcategories, or combinations of them, were identified as the cause of death in 33 cases (97.1%). Poor non-technical skills were considered to be a significant cause of adverse events in nearly half of the fatal medical accidents examined. Improving non-technical skills may be effective for reducing accidents, and training in particular subcategories of non-technical skills may be

  7. Occurrence and countermeasures of urban power grid accident

    NASA Astrophysics Data System (ADS)

    Wei, Wang; Tao, Zhang

    2018-03-01

    With the advance of technology, the development of network communication and the extensive use of power grids, people can get to know power grid accidents around the world through the network timely. Power grid accidents occur frequently. Large-scale power system blackout and casualty accidents caused by electric shock are also fairly commonplace. All of those accidents have seriously endangered the property and personal safety of the country and people, and the development of society and economy is severely affected by power grid accidents. Through the researches on several typical cases of power grid accidents at home and abroad in recent years and taking these accident cases as the research object, this paper will analyze the three major factors that cause power grid accidents at present. At the same time, combining with various factors and impacts caused by power grid accidents, the paper will put forward corresponding solutions and suggestions to prevent the occurrence of the accident and lower the impact of the accident.

  8. 49 CFR 382.303 - Post-accident testing.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... functions with respect to the vehicle, if the accident involved the loss of human life; or (2) Who receives a citation within 8 hours of the occurrence under State or local law for a moving traffic violation... performing safety-sensitive functions with respect to the vehicle, if the accident involved the loss of human...

  9. 49 CFR 382.303 - Post-accident testing.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... functions with respect to the vehicle, if the accident involved the loss of human life; or (2) Who receives... performing safety-sensitive functions with respect to the vehicle, if the accident involved the loss of human life; or (2) Who receives a citation within thirty-two hours of the occurrence under State or local law...

  10. [Prevention of road accidents in the road haulage field].

    PubMed

    Rosso, G L; Zanelli, R; Corino, P; Bruno, S

    2007-01-01

    Every year many traffic accidents with fatal outcomes occur in our Country. According to the recent indications of the European Agency for Safety and Health at Work, the Piedmont region has financed the plan: Prevention of road accidents in the road haulage field. The aims of the plan are to stimulate transport companies to the target of road safety and to improve and enforce sanitary surveillance, in order to improve the safety on road haulage and to prevent traffic injuries. the plan foresees, over a period of two years, a few encounters with all the interested parties (companies, police forces, labour unions etc). During those encounters we have to give a questionnaire for evaluating the companies' knowledge about the problem and we have to choose a common plan with the aim of improving road safety. The Piedmont regional plan recalls the need to increase the attention to numerous and diversified hazards for safety on road haulage. It also imposes the choice of measures that include: risk assessment, health education, technical and environmental prevention, sanitary surveillance and clinical interventions (diagnosis and rehabilitation of occupational accidents).

  11. An Analysis of Water Safety Behaviors among Migrant and Economically/Educationally Disadvantaged Middle School Students

    ERIC Educational Resources Information Center

    Sbarbaro, Victor S.; Enyeart Smith, Theresa M.

    2011-01-01

    This water safety study was both descriptive and exploratory in nature. The purpose was for middle school students to assess their own water safety experiences and to help school decision-makers determine the extent of drowning/water accidents. In July 2009, a water safety survey was administered to 122 students participating in the local Summer…

  12. Contributing factors in construction accidents.

    PubMed

    Haslam, R A; Hide, S A; Gibb, A G F; Gyi, D E; Pavitt, T; Atkinson, S; Duff, A R

    2005-07-01

    This overview paper draws together findings from previous focus group research and studies of 100 individual construction accidents. Pursuing issues raised by the focus groups, the accident studies collected qualitative information on the circumstances of each incident and the causal influences involved. Site based data collection entailed interviews with accident-involved personnel and their supervisor or manager, inspection of the accident location, and review of appropriate documentation. Relevant issues from the site investigations were then followed up with off-site stakeholders, including designers, manufacturers and suppliers. Levels of involvement of key factors in the accidents were: problems arising from workers or the work team (70% of accidents), workplace issues (49%), shortcomings with equipment (including PPE) (56%), problems with suitability and condition of materials (27%), and deficiencies with risk management (84%). Employing an ergonomics systems approach, a model is proposed, indicating the manner in which originating managerial, design and cultural factors shape the circumstances found in the work place, giving rise to the acts and conditions which, in turn, lead to accidents. It is argued that attention to the originating influences will be necessary for sustained improvement in construction safety to be achieved.

  13. Economic development, mobility and traffic accidents in Algeria.

    PubMed

    Bougueroua, M; Carnis, L

    2016-07-01

    The aim of this contribution is to estimate the impact of road economic conditions and mobility on traffic accidents for the case of Algeria. Using the cointegration approach and vector error correction model (VECM), we will examine simultaneously short term and long-term impacts between the number of traffic accidents, fuel consumption and gross domestic product (GDP) per capital, over the period 1970-2013. The main results of the estimation show that the number of traffic accidents in Algeria is positively influenced by the GDP per capita in the short and long term. It implies that a higher economic development worsens the road safety situation. However, the new traffic rules adopted in 2009 have an impact on the forecast trend of traffic accidents, meaning efficient public policy could improve the situation. This result calls for a strong political commitment with effective countermeasures for avoiding the further deterioration of road safety record in Algeria. Copyright © 2016 Elsevier Ltd. All rights reserved.

  14. Handle Yourself with Care: An Instructor's Guide for an Accident Prevention Course for Older Americans.

    ERIC Educational Resources Information Center

    Lewis, Dorothea J.; Winsor, Richard J.

    Accidents are the first cause of crippling and, many times, of death, among older people. To help reduce the possibility of accidents among older people, the Administration on Aging and the National Safety Council have joined in preparing this booklet--a course of instruction in safety and accident prevention for Older Americans. It spells out…

  15. Safety Management Information Statistics (SAMIS) - 1991 Annual Report

    DOT National Transportation Integrated Search

    1993-02-01

    The Safety Management Information Statistics 1991 Annual Report is a compilation and analysis of mass transit accident and casualty statistics reported by transit systems in the United States during 1991, under FTA's Section 15 reporting system.

  16. Safety Management Information Statistics (SAMIS) - 1994 Annual Report

    DOT National Transportation Integrated Search

    1996-07-01

    The Safety Management Information Statistics 1994 Annual Report is a compilation and analysis of mass transit accident and casualty statistics reported by transit systems in the United States during 1994, reported under the Federal Transit Administra...

  17. Bayesian networks for maritime traffic accident prevention: benefits and challenges.

    PubMed

    Hänninen, Maria

    2014-12-01

    Bayesian networks are quantitative modeling tools whose applications to the maritime traffic safety context are becoming more popular. This paper discusses the utilization of Bayesian networks in maritime safety modeling. Based on literature and the author's own experiences, the paper studies what Bayesian networks can offer to maritime accident prevention and safety modeling and discusses a few challenges in their application to this context. It is argued that the capability of representing rather complex, not necessarily causal but uncertain relationships makes Bayesian networks an attractive modeling tool for the maritime safety and accidents. Furthermore, as the maritime accident and safety data is still rather scarce and has some quality problems, the possibility to combine data with expert knowledge and the easy way of updating the model after acquiring more evidence further enhance their feasibility. However, eliciting the probabilities from the maritime experts might be challenging and the model validation can be tricky. It is concluded that with the utilization of several data sources, Bayesian updating, dynamic modeling, and hidden nodes for latent variables, Bayesian networks are rather well-suited tools for the maritime safety management and decision-making. Copyright © 2014 Elsevier Ltd. All rights reserved.

  18. Traffic Accidents Involving Cyclists Identifying Causal Factors Using Questionnaire Survey, Traffic Accident Data, and Real-World Observation.

    PubMed

    Oikawa, Shoko; Hirose, Toshiya; Aomura, Shigeru; Matsui, Yasuhiro

    2016-11-01

    The purpose of this study is to clarify the mechanism of traffic accidents involving cyclists. The focus is on the characteristics of cyclist accidents and scenarios, because the number of traffic accidents involving cyclists in Tokyo is the highest in Japan. First, dangerous situations in traffic incidents were investigated by collecting data from 304 cyclists in one city in Tokyo using a questionnaire survey. The survey indicated that cyclists used their bicycles generally while commuting to work or school in the morning. Second, the study investigated the characteristics of 250 accident situations involving cyclists that happened in the city using real-world bicycle accident data. The results revealed that the traffic accidents occurred at intersections of local streets, where cyclists collided most often with vehicles during commute time in the morning. Third, cyclists' behavior was observed at a local street intersection in the morning in the city using video pictures. In one hour during the morning commute period, 250 bicycles passed through the intersection. The results indicated that one of the reasons for traffic accidents involving cyclists might be the combined effect of low visibility, caused by the presence of box-like building structures close to the intersections, and the cyclists' behavior in terms of their velocity and no confirming safety. It was observed that, on average, bicycle velocity was 3.1 m/s at the initial line of an intersection. The findings from this study could be useful in developing new technologies to improve cyclist safety, such as alert devices for cyclists and vehicle drivers, wireless communication systems between cyclists and vehicle drivers, or advanced vehicles with bicycle detection and collision mitigation systems.

  19. [Proposal of a method for collective analysis of work-related accidents in the hospital setting].

    PubMed

    Osório, Claudia; Machado, Jorge Mesquita Huet; Minayo-Gomez, Carlos

    2005-01-01

    The article presents a method for the analysis of work-related accidents in hospitals, with the double aim of analyzing accidents in light of actual work activity and enhancing the vitality of the various professions that comprise hospital work. This process involves both research and intervention, combining knowledge output with training of health professionals, fostering expanded participation by workers in managing their daily work. The method consists of stimulating workers to recreate the situation in which a given accident occurred, shifting themselves to the position of observers of their own work. In the first stage of analysis, workers are asked to show the work analyst how the accident occurred; in the second stage, the work accident victim and analyst jointly record the described series of events in a diagram; in the third, the resulting record is re-discussed and further elaborated; in the fourth, the work accident victim and analyst evaluate and implement measures aimed to prevent the accident from recurring. The article concludes by discussing the method's possibilities and limitations in the hospital setting.

  20. Safety distance assessment of industrial toxic releases based on frequency and consequence: a case study in Shanghai, China.

    PubMed

    Yu, Q; Zhang, Y; Wang, X; Ma, W C; Chen, L M

    2009-09-15

    A case study on the safety distance assessment of a chemical industry park in Shanghai, China, is presented in this paper. Toxic releases were taken into consideration. A safety criterion based on frequency and consequence of major hazard accidents was set up for consequence analysis. The exposure limits for the accidents with the frequency of more than 10(-4), 10(-5)-10(-4) and 10(-6)-10(-5) per year were mortalities of 1% (or SLOT), 50% (SLOD) and 75% (twice of SLOD) respectively. Accidents with the frequency of less than 10(-6) per year were considered incredible and ignored in the consequence analysis. Taking the safety distance of all the hazard installations in a chemical plant into consideration, the results based on the new criterion were almost smaller than those based on LC50 or SLOD. The combination of the consequence and risk based results indicated that the hazard installations in two of the chemical plants may be dangerous to the protection targets and measurements had to be taken to reduce the risk. The case study showed that taking account of the frequency of occurrence in the consequence analysis would give more feasible safety distances for major hazard accidents and the results were more comparable to those calculated by risk assessment.

  1. Safety assessment methodology in management of spent sealed sources.

    PubMed

    Mahmoud, Narmine Salah

    2005-02-14

    Environmental hazards can be caused from radioactive waste after their disposal. It was therefore important that safety assessment methodologies be developed and established to study and estimate the possible hazards, and institute certain safety methodologies that lead and prevent the evolution of these hazards. Spent sealed sources are specific type of radioactive waste. According to IAEA definition, spent sealed sources are unused sources because of activity decay, damage, misuse, loss, or theft. Accidental exposure of humans from spent sealed sources can occur at the moment they become spent and before their disposal. Because of that reason, safety assessment methodologies were tailored to suit the management of spent sealed sources. To provide understanding and confidence of this study, validation analysis was undertaken by considering the scenario of an accident that occurred in Egypt, June 2000 (the Meet-Halfa accident from an iridium-192 source). The text of this work includes consideration related to the safety assessment approaches of spent sealed sources which constitutes assessment context, processes leading an active source to be spent, accident scenarios, mathematical models for dose calculations, and radiological consequences and regulatory criteria. The text also includes a validation study, which was carried out by evaluating a theoretical scenario compared to the real scenario of Meet-Halfa accident depending on the clinical assessment of affected individuals.

  2. Understanding factors associated with misclassification of fatigue-related accidents in police record.

    PubMed

    Li, Yanyan; Yamamoto, Toshiyuki; Zhang, Guangnan

    2018-02-01

    Fatigue is one of the riskiest causes of traffic accidents threatening road safety. Due to lack of proper criteria, the identification of fatigue-related accidents by police officers largely depends on inferential evidence and their own experience. As a result, many fatigue-related accidents are misclassified and the harmfulness of fatigue on road safety is misestimated. In this paper, a joint model framework is introduced to analyze factors contributing to misclassification of a fatigue-related accident in police reports. Association rule data mining technique is employed to identify the potential interactions of factors, and logistic regression models are applied to analyze factors that hinder police officers' identification of fatigue-related accidents. Using the fatigue-related crash records from Guangdong Province during 2005-2014, factors contributing to the false positive and false negative detection of the fatigue-related accident have been identified and compared. Some variables and interactions were identified to have significant impacts on fatigue-related accident detection. Based on the results, it can be inferred that the stereotype of certain groups of drivers, crash types, and roadway conditions affects police officers' judgment on fatigue-related accidents. This finding can provide useful information for training police officers and build better criteria for fatigue identification. Copyright © 2017 National Safety Council and Elsevier Ltd. All rights reserved.

  3. Processes of technology assessment: The National Transportation Safety Board

    NASA Technical Reports Server (NTRS)

    Weiss, E.

    1972-01-01

    The functions and operations of the Safety Board as related to technology assessment are described, and a brief history of the Safety Board is given. Recommendations made for safety in all areas of transportation and the actions taken are listed. Although accident investigation is an important aspect of NTSB's activity, it is felt that the greatest contribution is in pressing for development of better accident prevention programs. Efforts of the Safety Board in changing transportation technology to improve safety and prevent accidents are illustrated.

  4. Traits and causes of environmental loss-related chemical accidents in China based on co-word analysis.

    PubMed

    Wu, Desheng; Song, Yu; Xie, Kefan; Zhang, Baofeng

    2018-04-25

    Chemical accidents are major causes of environmental losses and have been debated due to the potential threat to human beings and environment. Compared with the single statistical analysis, co-word analysis of chemical accidents illustrates significant traits at various levels and presents data into a visual network. This study utilizes a co-word analysis of the keywords extracted from the Web crawling texts of environmental loss-related chemical accidents and uses the Pearson's correlation coefficient to examine the internal attributes. To visualize the keywords of the accidents, this study carries out a multidimensional scaling analysis applying PROXSCAL and centrality identification. The research results show that an enormous environmental cost is exacted, especially given the expected environmental loss-related chemical accidents with geographical features. Meanwhile, each event often brings more than one environmental impact. Large number of chemical substances are released in the form of solid, liquid, and gas, leading to serious results. Eight clusters that represent the traits of these accidents are formed, including "leakage," "poisoning," "explosion," "pipeline crack," "river pollution," "dust pollution," "emission," and "industrial effluent." "Explosion" and "gas" possess a strong correlation with "poisoning," located at the center of visualization map.

  5. Accident analysis of heavy water cooled thorium breeder reactor

    NASA Astrophysics Data System (ADS)

    Yulianti, Yanti; Su'ud, Zaki; Takaki, Naoyuki

    2015-04-01

    power reactor has a peak value before reactor has new balance condition. The analysis showed that temperatures of fuel and claddings during accident are still below limitations which are in secure condition.

  6. Development of a large truck safety data needs study plan. Vol. 1, Summary

    DOT National Transportation Integrated Search

    1986-02-01

    This report discusses the results of a study to determine the data needs necessary to address truck safety issues and to develop a data collection and analysis plan. Priority truck safety issues that are amenable to truck accident data analyses were ...

  7. "What--me worry?" "Why so serious?": a personal view on the Fukushima nuclear reactor accidents.

    PubMed

    Gallucci, Raymond

    2012-09-01

    Infrequently, it seems that a significant accident precursor or, worse, an actual accident, involving a commercial nuclear power reactor occurs to remind us of the need to reexamine the safety of this important electrical power technology from a risk perspective. Twenty-five years since the major core damage accident at Chernobyl in the Ukraine, the Fukushima reactor complex in Japan experienced multiple core damages as a result of an earthquake-induced tsunami beyond either the earthquake or tsunami design basis for the site. Although the tsunami itself killed tens of thousands of people and left the area devastated and virtually uninhabitable, much concern still arose from the potential radioactive releases from the damaged reactors, even though there was little population left in the area to be affected. As a lifelong probabilistic safety analyst in nuclear engineering, even I must admit to a recurrence of the doubt regarding nuclear power safety after Fukushima that I had experienced after Three Mile Island and Chernobyl. This article is my attempt to "recover" my personal perspective on acceptable risk by examining both the domestic and worldwide history of commercial nuclear power plant accidents and attempting to quantify the risk in terms of the frequency of core damage that one might glean from a review of operational history. © 2012 Society for Risk Analysis.

  8. Do failures in non-technical skills contribute to fatal medical accidents in Japan? A review of the 2010–2013 national accident reports

    PubMed Central

    Uramatsu, Masashi; Fujisawa, Yoshikazu; Mizuno, Shinya; Souma, Takahiro; Komatsubara, Akinori; Miki, Tamotsu

    2017-01-01

    Objectives We sought to clarify how large a proportion of fatal medical accidents can be considered to be caused by poor non-technical skills, and to support development of a policy to reduce number of such accidents by making recommendations about possible training requirements. Design Summaries of reports of fatal medical accidents, published by the Japan Medical Safety Research Organization, were reviewed individually. Three experienced clinicians and one patient safety expert conducted the reviews to determine the cause of death. Views of the patient safety expert were given additional weight in the overall determination. Setting A total of 73 summary reports of fatal medical accidents were reviewed. These reports had been submitted by healthcare organisations across Japan to the Japan Medical Safety Research Organization between April 2010 and March 2013. Primary and secondary outcome measures The cause of death in fatal medical accidents, categorised into technical skills, non-technical skills and inevitable progress of disease were evaluated. Non-technical skills were further subdivided into situation awareness, decision making, communication, team working, leadership, managing stress and coping with fatigue. Results Overall, the cause of death was identified as non-technical skills in 34 cases (46.6%), disease progression in 33 cases (45.2%) and technical skills in two cases (5.5%). In two cases, no consensual determination could be achieved. Further categorisation of cases of non-technical skills were identified as 14 cases (41.2%) of problems with situation awareness, eight (23.5%) with team working and three (8.8%) with decision making. These three subcategories, or combinations of them, were identified as the cause of death in 33 cases (97.1%). Conclusions Poor non-technical skills were considered to be a significant cause of adverse events in nearly half of the fatal medical accidents examined. Improving non-technical skills may be effective for

  9. A systematic review of the literature on safety measures to prevent railway suicides and trespassing accidents.

    PubMed

    Havârneanu, Grigore M; Burkhardt, Jean-Marie; Paran, Françoise

    2015-08-01

    This review covers a central aspect in railway safety which is the prevention of suicides and trespassing accidents. The paper attempts to answer the following research question: 'What measures are available to reduce railway suicide and trespass, and what is the evidence for their effectiveness?' The review is based on 139 relevant publications, ranging from 1978 to 2014. The analysis aimed to identify the past and current trend in the prevention practice by looking both quantitatively and qualitatively at the recommended measures. According to the results, there has been a constant focus on suicide prevention, and only relatively recent interest in trespass countermeasures. The content analysis revealed 19 main preventative categories which include more than 100 specific measures. We identified 16 common categories against railway suicide and trespass, and 3 categories of specific measures to prevent suicide. There are only 22 studies which provide empirical support for the effectiveness of measures. Actual combinations of measures are barely evaluated, but several challenges emerge from the literature. The discussion focuses on the need for a unified approach to suicide and trespass prevention, and on the importance to consider the effect mechanism of the measures in order to design better interventions. Copyright © 2015 Elsevier Ltd. All rights reserved.

  10. The use of flight test techniques in aircraft accident investigations

    NASA Technical Reports Server (NTRS)

    Parks, E. K.; Bach, R. E., Jr.; Wingrove, R. C.

    1986-01-01

    Wind shear is a serious safety hazard to commercial aviation. Low level wind shear (downburst) was the cause of the takeoff accident in New Orleans, July 9, 1982, and the landing accident in Dallas, Aug. 2, 1985. Shear layer instability is a common cause of clear air turbulence (CAT) at cruising altitudes. A number of encounters with severe CAT, in which passengers were injured, have recently occurred (Hannibal, MO, April 1981; Morton, WY, July 1982; etc.). Improved accident investigation techniques can lead to a better understanding of the nature of the wind environment associated with downbursts and CAT and to better detection and avoidance procedures. For the past several years, NASA-Ames has worked closely with the National Transportation Safety Board in the investigation of wind related accidents.

  11. [Research on accidents in a tire-producing plant].

    PubMed

    Mete, R; Sabatucci, A

    1989-09-30

    In the autumn of 1987 the U.S.L. health service (prevention, hygiene and occupational safety section) began a study about the accidents in a firm manufacturing tyres, placed in its own area. The retrospective enquiry starts from the analysis of typology, diffusion and seriousness of occupational accidents. The firm's accident register has been analyzed and integrated with other necessary information provided by the firm, by I.N.A.I.L. and by the air force metereological service. The study has been carried out on data concerning the following years: 1984-1985-1986. The accidents considered, implied absence from work and were divided as follows: for absence up till 3 days (in franchise), and more than 3 days (indemnified), applying the average value calculated on one year of the three analyzed. Every accident has been analyzed per year, month, day, hour of event. According to the classes: circumstances, kind of lesion, site of lesion, period of absence from work. The indices of: frequency, seriousness, incidence, mean duration have been calculated. The average monthly values of temperature: max and min. of the area and to the average monthly amount of processed elastomer (rate of production). The statistics we obtained, justified the study and showed the operative solution. The aspect of sanitary education and the general psychological aspect regarding the accident have been considered. Moreover the general operative solutions for the firm and specific ones for every department and for every position have been shown and faced up to. In this way, according to the risks that have emerged from the enquiries on previous accidents and thanks to direct inspection. it was possible to prevent accidents.

  12. The dynamic nature of risk perceptions after a fatal transit accident.

    PubMed

    Wernstedt, Kris; Murray-Tuite, Pamela

    2015-03-01

    In 2009, two trains of Washington, DC's Metrorail system collided, resulting in nine deaths and 50 serious injuries. Based on a multiwave survey of Metrorail users in the months after the crash, this article reports how the accident appears to have (1) changed over time the tradeoffs among safety, speed, frequency of service, cost, and reliability that the transit users stated they were willing to make in the postaccident period and (2) altered transit users' concerns about safety as a function of time and distance from the accident site. We employ conditional logit models to examine tradeoffs among stated preferences for system performance measures after the accident, as well as the influence that respondent characteristics of transit use, location, income, age, and gender have on these preference tradeoffs. As expected, respondents appear averse to longer headways between trains, longer travel durations, higher travel costs, a higher number of late trains, and a higher number of fatalities. The models also show evidence of higher aversion to fatalities from transit system operation among females compared to males. In addition, respondents less experienced with Metrorail travel and those with lower household incomes show higher aversion to fatalities, and this aversion increases as a subject's psychological distance from the accident site decreases. Contrary to expectations shaped by previous studies, aversion to fatalities appears to have increased between the early months after the accident and the end of the survey period, and the expected relationship between age and aversion to fatalities is not statistically significant. © 2014 Society for Risk Analysis.

  13. Fatal occupational accidents in Danish fishing vessels 1989-2005.

    PubMed

    Laursen, Lise H; Hansen, Henrik L; Jensen, Olaf C

    2008-06-01

    The purpose of the study was to study the circumstances and incidence rates of fatal accidents in inspection obligated and non-inspection obligated Danish fishing vessels to identify areas for prevention. Information about the fatalities came from maritime authority reports, including vessel disaster reports, post mortem reports, maritime inquiries and police reports. The person- and vessel years at risk came from the Danish Directorate of Fisheries. During the period 1989-2005, 114 fatalities occurred. Sixty-one of the fatalities occurred in 36 vessel disasters mainly caused by foundering/capsizing due to stability changes in rough weather and collisions; 39 fatal occupational accidents mainly occurred on the larger inspection obligated trawlers during fishing. In the remaining 14 other fatal accidents, the main causal factors were difficult embarking/disembarking conditions by darkness in foreign ports and alcohol intoxication. In the period 1995-2005, the overall incidence rate was 10 per 10,000 fishermen per year with no down-going trend during that period. The fatal accident rates are still too high, despite the efforts to reduce the risk. Increased focus on regular and repeated safety training for all fishermen and improved safety measures are needed, especially in the underscored areas of sea disasters concerning small vessels and occupational accidents on big vessels. Better registration of time at risk for fishermen is needed to validate the effect of the safety measures.

  14. Road safety and road traffic accidents in Saudi Arabia

    PubMed Central

    Mansuri, Farah A.; Al-Zalabani, Abdulmohsen H.; Zalat, Marwa M.; Qabshawi, Reem I.

    2015-01-01

    Objectives: To identify the changing trends and crucial preventive approaches to road traffic accidents (RTAs) adopted in the Kingdom of Saudi Arabia (KSA) over the last 2.5 decades, and to analyze aspects previously overlooked. Methods: This systematic review was based on evidence of RTAs in KSA. All articles published during the last 25 years on road traffic accident in KSA were analyzed. This study was carried out from December 2013 to May 2014 in the Department of Family and Community Medicine, Taibah University, Al-Madinah Al-Munawwarah, KSA. Results: Road traffic accidents accounted for 83.4% of all trauma admissions in 1984-1989, and no such overall trend was studied thereafter. The most frequently injured body regions as reported in the latest studies were head and neck, followed by upper and lower extremities, which was found to be opposite to that of the studies reported earlier. Hospital data showed an 8% non-significant increase in road accident mortalities in contrast to police records of a 27% significant reduction during the years 2005-2010. Excessive speeding was the most common cause reported in all recent and past studies. Conclusion: Disparity was common in the type of reporting of RTAs, outcome measures, and possible causes over a period of 2.5 decade. All research exclusively looked into the drivers’ faults. A sentinel surveillance of road crashes should be kept in place in the secondary and tertiary care hospitals for all regions of KSA. PMID:25828277

  15. 782 consecutive construction work accidents: who is at risk? A 10-year analysis from a Swiss university hospital trauma unit.

    PubMed

    Frickmann, Frank; Wurm, Benjamin; Jeger, Victor; Lehmann, Beat; Zimmermann, Heinz; Exadaktylos, Aristomenis K

    2012-09-06

    Mortality and morbidity are particularly high in the building industry. The annual rate of non-fatal occupational accidents in Switzerland is 1,133 per 100,000 inhabitants. Retrospective analysis of the electronic database of a university emergency centre. Between 2001 and 2011, 782 occupational accidents to construction workers were recorded and analysed using specific demographic and medical keywords. Most patients were aged 30-39 (30.4%). 66.4% of the injured workers were foreigners. This is almost twice as high as the overall proportion of foreigners in Switzerland or in the Swiss labour market. 16% of the Swiss construction workers and 8% of the foreign construction workers suffered a severe injury with ISS >15. There was a trend for workers aged 60 and above to suffer an accident with a high ISS (p = 0.089). As in other European countries, most patients were in their thirties. Older construction workers suffered fewer injuries, although these tended to be more severe. The injuries were evenly distributed through the working days of the week. A special effort should be made that current health and safety measures are understood and applied by foreign and older construction workers.

  16. 49 CFR 225.9 - Telephonic reports of certain accidents/incidents and other events.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ...-rail grade crossing when death occurs within 24 hours of the accident/incident; (iv) A train accident... of rail accidents for the National Transportation Safety Board (49 CFR part 840) and the Research and...

  17. 49 CFR 225.9 - Telephonic reports of certain accidents/incidents and other events.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ...-rail grade crossing when death occurs within 24 hours of the accident/incident; (iv) A train accident... of rail accidents for the National Transportation Safety Board (49 CFR part 840) and the Research and...

  18. 49 CFR 225.9 - Telephonic reports of certain accidents/incidents and other events.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ...-rail grade crossing when death occurs within 24 hours of the accident/incident; (iv) A train accident... of rail accidents for the National Transportation Safety Board (49 CFR part 840) and the Research and...

  19. 49 CFR 225.9 - Telephonic reports of certain accidents/incidents and other events.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ...-rail grade crossing when death occurs within 24 hours of the accident/incident; (iv) A train accident... of rail accidents for the National Transportation Safety Board (49 CFR part 840) and the Research and...

  20. Global ship accidents and ocean swell-related sea states

    NASA Astrophysics Data System (ADS)

    Zhang, Zhiwei; Li, Xiao-Ming

    2017-11-01

    With the increased frequency of shipping activities, navigation safety has become a major concern, especially when economic losses, human casualties and environmental issues are considered. As a contributing factor, the sea state plays a significant role in shipping safety. However, the types of dangerous sea states that trigger serious shipping accidents are not well understood. To address this issue, we analyzed the sea state characteristics during ship accidents that occurred in poor weather or heavy seas based on a 10-year ship accident dataset. Sea state parameters of a numerical wave model, i.e., significant wave height, mean wave period and mean wave direction, were analyzed for the selected ship accident cases. The results indicated that complex sea states with the co-occurrence of wind sea and swell conditions represent threats to sailing vessels, especially when these conditions include similar wave periods and oblique wave directions.