Sustainable in-well vapor stripping: A design, analytical model, and pilot study for groundwater remediation.

PubMed

Sutton, Patrick T; Ginn, Timothy R

2014-12-15

A sustainable in-well vapor stripping system is designed as a cost-effective alternative for remediation of shallow chlorinated solvent groundwater plumes. A solar-powered air compressor is used to inject air bubbles into a monitoring well to strip volatile organic compounds from a liquid to vapor phase while simultaneously inducing groundwater circulation around the well screen. An analytical model of the remediation process is developed to estimate contaminant mass flow and removal rates. The model was calibrated based on a one-day pilot study conducted in an existing monitoring well at a former dry cleaning site. According to the model, induced groundwater circulation at the study site increased the contaminant mass flow rate into the well by approximately two orders of magnitude relative to ambient conditions. Modeled estimates for 5h of pulsed air injection per day at the pilot study site indicated that the average effluent concentrations of dissolved tetrachloroethylene and trichloroethylene can be reduced by over 90% relative to the ambient concentrations. The results indicate that the system could be used cost-effectively as either a single- or multi-well point technology to substantially reduce the mass of dissolved chlorinated solvents in groundwater. Copyright © 2014 Elsevier B.V. All rights reserved.

28 CFR 571.72 - Additional designated offenses.

Code of Federal Regulations, 2014 CFR

2014-07-01

... sexual contact with another person without obtaining permission to do so (forcible rape, sexual assault... (Assault) if it includes assault with the intent to commit first degree sexual abuse, second degree sexual... designated offenses. The following offenses are designated as additional sexual offenses for purposes of 18 U...

28 CFR 571.72 - Additional designated offenses.

Code of Federal Regulations, 2013 CFR

2013-07-01

... sexual contact with another person without obtaining permission to do so (forcible rape, sexual assault... (Assault) if it includes assault with the intent to commit first degree sexual abuse, second degree sexual... designated offenses. The following offenses are designated as additional sexual offenses for purposes of 18 U...

28 CFR 571.72 - Additional designated offenses.

Code of Federal Regulations, 2012 CFR

2012-07-01

... sexual contact with another person without obtaining permission to do so (forcible rape, sexual assault... (Assault) if it includes assault with the intent to commit first degree sexual abuse, second degree sexual... designated offenses. The following offenses are designated as additional sexual offenses for purposes of 18 U...

28 CFR 571.72 - Additional designated offenses.

Code of Federal Regulations, 2011 CFR

2011-07-01

... sexual contact with another person without obtaining permission to do so (forcible rape, sexual assault... (Assault) if it includes assault with the intent to commit first degree sexual abuse, second degree sexual... designated offenses. The following offenses are designated as additional sexual offenses for purposes of 18 U...

What are you trying to learn? Study designs and the appropriate analysis for your research question

USDA-ARS?s Scientific Manuscript database

One fundamental necessity in the entire process of a well-performed study is the experimental design. A well-designed study can help researchers understand and have confidence in their results and analyses, and additionally the agreement or disagreement with the stated hypothesis. This well-designed...

Additive Manufacturing Design Considerations for Liquid Engine Components

NASA Technical Reports Server (NTRS)

Whitten, Dave; Hissam, Andy; Baker, Kevin; Rice, Darron

2014-01-01

The Marshall Space Flight Center's Propulsion Systems Department has gained significant experience in the last year designing, building, and testing liquid engine components using additive manufacturing. The department has developed valve, duct, turbo-machinery, and combustion device components using this technology. Many valuable lessons were learned during this process. These lessons will be the focus of this presentation. We will present criteria for selecting part candidates for additive manufacturing. Some part characteristics are 'tailor made' for this process. Selecting the right parts for the process is the first step to maximizing productivity gains. We will also present specific lessons we learned about feature geometry that can and cannot be produced using additive manufacturing machines. Most liquid engine components were made using a two-step process. The base part was made using additive manufacturing and then traditional machining processes were used to produce the final part. The presentation will describe design accommodations needed to make the base part and lessons we learned about which features could be built directly and which require the final machine process. Tolerance capabilities, surface finish, and material thickness allowances will also be covered. Additive Manufacturing can produce internal passages that cannot be made using traditional approaches. It can also eliminate a significant amount of manpower by reducing part count and leveraging model-based design and analysis techniques. Information will be shared about performance enhancements and design efficiencies we experienced for certain categories of engine parts.

76 FR 25405 - Additional Designations, Foreign Narcotics Kingpin Designation Act

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-04

... Narcotics Kingpin Designation Act. The list of additional designees is as follows: 1. SHAYESTEH, Bahram Ali (a.k.a. JADALI, Bahrami Ali; a.k.a. SHAYESTEH, Bahrami Ali), 80331 Muenchen, Bayern, Germany; DOB 6...

Using generalized additive (mixed) models to analyze single case designs.

PubMed

Shadish, William R; Zuur, Alain F; Sullivan, Kristynn J

2014-04-01

This article shows how to apply generalized additive models and generalized additive mixed models to single-case design data. These models excel at detecting the functional form between two variables (often called trend), that is, whether trend exists, and if it does, what its shape is (e.g., linear and nonlinear). In many respects, however, these models are also an ideal vehicle for analyzing single-case designs because they can consider level, trend, variability, overlap, immediacy of effect, and phase consistency that single-case design researchers examine when interpreting a functional relation. We show how these models can be implemented in a wide variety of ways to test whether treatment is effective, whether cases differ from each other, whether treatment effects vary over cases, and whether trend varies over cases. We illustrate diagnostic statistics and graphs, and we discuss overdispersion of data in detail, with examples of quasibinomial models for overdispersed data, including how to compute dispersion and quasi-AIC fit indices in generalized additive models. We show how generalized additive mixed models can be used to estimate autoregressive models and random effects and discuss the limitations of the mixed models compared to generalized additive models. We provide extensive annotated syntax for doing all these analyses in the free computer program R. Copyright © 2013 Society for the Study of School Psychology. Published by Elsevier Ltd. All rights reserved.

Personalized Progressive Addition Lenses: Correlation between Performance and Design.

PubMed

Forkel, Johanne; Reiniger, Jenny Lorén; Muschielok, Adam; Welk, Andrea; Seidemann, Anne; Baumbach, Peter

2017-02-01

A continuous set of personalized designs (design space) for progressive addition lenses (PALs) is investigated. The main goals are (1) to study how the subjects' perception of a personalized design depends on its position in the design space and (2) to compare the performance of personalized PALs to a conventional PAL with a fixed design. In a double-blind study, 51 subjects compared Rodenstock Impression FreeSign 3, which is a family of PALs with a continuously controllable personalized design, and Rodenstock Progressiv Life Free, which is a conventional PAL with a single fixed design. The positions and sizes of viewing zones and the softness of gradients of mean power and astigmatism of personalized lenses were customized to individual viewing preferences. These designs were represented as points in a design space comprising a continuum of PAL designs. Subjective ratings and experimental measurements were used to study viewing zone widths, blur gradient smoothness, amount of distortion, the feeling of safety during motion, and overall wearing comfort. (1) Far viewing zone width (experiments and ratings), near viewing zone width (experiments), blur gradient smoothness, and the amount of distortion (ratings) were significantly dependent on the position of the personalized lens design in the design space. This was consistent with the structure of the design space. (2) 82% of the subjects chose personalized lenses as their favorite. Most subjects reported higher wearing comfort and tolerability with personalized lenses than with conventional lenses. The designs of the tested personalized lenses were perceived by the subjects as intended. This is a prerequisite to the successful customization of PALs to individual wearing preferences. Possible reasons for the preference of the tested personalized lenses are the optimization with respect to individual wearing conditions and the personalization.

Social Interaction Needs and Entertainment Approaches to Pregnancy Well-Being in mHealth Technology Design for Low-Income Transmigrant Women: Qualitative Codesign Study

PubMed Central

2018-01-01

Background Low-income Caribbean transmigrant women face unique health challenges during pregnancy that set forth multidimensional implications for the design of mobile health (mHealth). Acknowledgment of the unique health needs of low-income Caribbean immigrant women in the United States and what that entails regarding technology design remains rarely examined in the literature of mHealth technologies. Objective The goal of this study was to reveal the needs and gaps in mHealth interventions for pregnant immigrant women not yet realized in this field. These understandings reveal design opportunities for mHealth. Methods The use of the qualitative participatory action research approach of codesign workshops in this study resulted in design solutions by the participants after reflecting on their earlier focus group discussions. The highlights are not the resulting designs per se but rather the inferences derived from the researcher reflecting on these designs. Results The designs exposed two themes relevant to this paper. First, the participants desired the inclusion and rebuilding of social and organizational relationships in mHealth. The resulting designs formulate an understanding of the women’s health-related social support needs and how technology can facilitate them. Second, the participants wanted entertainment with an element of social participation incorporated in mHealth pregnancy management interventions. This brings attention to the role entertainment can add to the impact mHealth can deliver for pregnancy well-being. Conclusions The study concluded with an examination of social and entertainment design implications that reveal pregnant immigrant women’s virtual health-related sharing habits, choice of sharing interaction scenarios during pregnancy (eg, local, long distance, one-way, two-way, and many-many), and choice of sharing media (eg, text, voice, and video). Additionally, the study revealed exclusions to social sharing capabilities in health

Social Interaction Needs and Entertainment Approaches to Pregnancy Well-Being in mHealth Technology Design for Low-Income Transmigrant Women: Qualitative Codesign Study.

PubMed

AlJaberi, Hana

2018-04-13

Low-income Caribbean transmigrant women face unique health challenges during pregnancy that set forth multidimensional implications for the design of mobile health (mHealth). Acknowledgment of the unique health needs of low-income Caribbean immigrant women in the United States and what that entails regarding technology design remains rarely examined in the literature of mHealth technologies. The goal of this study was to reveal the needs and gaps in mHealth interventions for pregnant immigrant women not yet realized in this field. These understandings reveal design opportunities for mHealth. The use of the qualitative participatory action research approach of codesign workshops in this study resulted in design solutions by the participants after reflecting on their earlier focus group discussions. The highlights are not the resulting designs per se but rather the inferences derived from the researcher reflecting on these designs. The designs exposed two themes relevant to this paper. First, the participants desired the inclusion and rebuilding of social and organizational relationships in mHealth. The resulting designs formulate an understanding of the women's health-related social support needs and how technology can facilitate them. Second, the participants wanted entertainment with an element of social participation incorporated in mHealth pregnancy management interventions. This brings attention to the role entertainment can add to the impact mHealth can deliver for pregnancy well-being. The study concluded with an examination of social and entertainment design implications that reveal pregnant immigrant women's virtual health-related sharing habits, choice of sharing interaction scenarios during pregnancy (eg, local, long distance, one-way, two-way, and many-many), and choice of sharing media (eg, text, voice, and video). Additionally, the study revealed exclusions to social sharing capabilities in health technologies for these women. ©Hana Al

Fluid loss control additives for oil well cementing compositions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crema, S.C.; Kucera, C.H.

1992-03-03

This patent describes a cementing composition useful in cementing oil, gas and water wells. It comprises hydraulic cement; and a fluid loss additive in an amount effective to reduce fluid loss, the fluid loss additive comprised of a copolymer of acrylamide monomer and vinyl formamide monomer and derivatives thereof in a weight percent ratio of from about 95:5 to 5:95, the copolymer having a molecular weight range of from about 10,000 to 3,000,000, the acrylamide monomer being selected from the group consisting of acrylamide, methacrylamide, N,N-dimethyl(meth)acrylamide, dialkylaminoalkyl(meth) acrylamide and mixtures thereof, the vinyl formamide monomer being selected from the groupmore » consisting of vinyl formamide, its hydrolysis products and derivatives thereof.« less

Liquid belt radiator design study

NASA Technical Reports Server (NTRS)

Teagan, W. P.; Fitzgerald, K. F.

1986-01-01

The Liquid Belt Radiator (LBR) is an advanced concept developed to meet the needs of anticipated future space missions. A previous study documented the advantages of this concept as a lightweight, easily deployable alternative to present day space heat rejection systems. The technical efforts associated with this study concentrate on refining the concept of the LBR as well as examining the issues of belt dynamics and potential application of the LBR to intermediate and high temperature heat rejection applications. A low temperature point design developed in previous work is updated assuming the use of diffusion pump oil, Santovac-6, as the heat transfer media. Additional analytical and design effort is directed toward determining the impact of interface heat exchanger, fluid bath sealing, and belt drive mechanism designs on system performance and mass. The updated design supports the earlier result by indicating a significant reduction in system specific system mass as compared to heat pipe or pumped fluid radiator concepts currently under consideration (1.3 kg/sq m versus 5 kg/sq m).

Evidence-Based Communication Practices for Children with Visual Impairments and Additional Disabilities: An Examination of Single-Subject Design Studies

ERIC Educational Resources Information Center

Parker, Amy T.; Grimmett, Eric S.; Summers, Sharon

2008-01-01

This review examines practices for building effective communication strategies for children with visual impairments, including those with additional disabilities, that have been tested by single-subject design methodology. The authors found 30 studies that met the search criteria and grouped intervention strategies to align any evidence of the…

Progressive addition spectacle lenses: Design preferences and head movements while reading

NASA Astrophysics Data System (ADS)

Preston, Julie Lynn

In a subjective preference study, two key progressive addition lens parameters, near zone width and corridor length, were varied in a double-masked, randomized, clinical trial of 49 patients. Each subject received a complete eye examination and a new frame. Each wore 6 pairs of lenses for one week at a time and completed questionnaires relating to vision, adaptation, and satisfaction. The preferred lens was identified from the three near zone width lenses and from the three corridor length lenses. Patient characteristics were analyzed for their effect on design preference. Satisfaction ratings following a brief experience with each design were compared to ratings after one week of wear in order to ascertain the predictability of initial impressions. One lens design appeared twice in the preference trial, providing an assessment of the repeatability of the rating instrument. The lens design with the widest near zone was rated significantly lower than the other near zone width designs for nearly every question relating to vision, adaptation, and satisfaction. This lens was also least preferred of all the designs. Preferences for corridor length were evenly distributed among the three designs. Of patient characteristics, years of progressive addition lens wear and gender significantly affected design preference in this population. Initial impressions were not predictive of satisfaction after a week of wear. The rating instrument was judged to have low repeatability. In the head movement portion of the study, 18 participants from the preference study wore the three near zone width designs while reading three paragraphs of varying print size. From a 20 second recording for each of three different paragraphs with each lens, measures of head rotation and posture were collected. The amplitude of head rotation was significantly affected by print size but not by lens design. The effective zone widths on the lenses scanned by the eyes and the locations of the reading levels

21 CFR 514.117 - Adequate and well-controlled studies.

Code of Federal Regulations, 2011 CFR

2011-04-01

... experimental units. When the effect of such variables is accounted for by an appropriate design, and when... and well-controlled study should provide sufficient details of study design, conduct, and analysis to... the new animal drug used in the study. (4) The study uses a design that permits a valid comparison...

21 CFR 514.117 - Adequate and well-controlled studies.

Code of Federal Regulations, 2012 CFR

2012-04-01

... experimental units. When the effect of such variables is accounted for by an appropriate design, and when... and well-controlled study should provide sufficient details of study design, conduct, and analysis to... the new animal drug used in the study. (4) The study uses a design that permits a valid comparison...

21 CFR 514.117 - Adequate and well-controlled studies.

Code of Federal Regulations, 2014 CFR

2014-04-01

... experimental units. When the effect of such variables is accounted for by an appropriate design, and when... and well-controlled study should provide sufficient details of study design, conduct, and analysis to... the new animal drug used in the study. (4) The study uses a design that permits a valid comparison...

21 CFR 514.117 - Adequate and well-controlled studies.

Code of Federal Regulations, 2013 CFR

2013-04-01

... experimental units. When the effect of such variables is accounted for by an appropriate design, and when... and well-controlled study should provide sufficient details of study design, conduct, and analysis to... the new animal drug used in the study. (4) The study uses a design that permits a valid comparison...

21 CFR 514.117 - Adequate and well-controlled studies.

Code of Federal Regulations, 2010 CFR

2010-04-01

... experimental units. When the effect of such variables is accounted for by an appropriate design, and when... and well-controlled study should provide sufficient details of study design, conduct, and analysis to... the new animal drug used in the study. (4) The study uses a design that permits a valid comparison...

Design and additive manufacture for flow chemistry.

PubMed

Capel, Andrew J; Edmondson, Steve; Christie, Steven D R; Goodridge, Ruth D; Bibb, Richard J; Thurstans, Matthew

2013-12-07

We review the use of additive manufacturing (AM) as a novel manufacturing technique for the production of milli-scale reactor systems. Five well-developed additive manufacturing techniques: stereolithography (SL), multi-jet modelling (MJM), selective laser melting (SLM), laser sintering (LS) and fused deposition modelling (FDM) were used to manufacture a number of miniaturised reactors which were tested using a range of organic and inorganic reactions.

Review of Well Operator Files for Hydraulically Fractured Oil and Gas Production Wells: Well Design and Construction Fact Sheet

EPA Pesticide Factsheets

EPA reviewed a statistically representative sample of oil and gas production wells reported by nine service companies to help understand the role of well design and construction practices preventing pathways for subsurface fluid movement.

Survey of rural, private wells. Statistical design

USGS Publications Warehouse

Mehnert, Edward; Schock, Susan C.; ,

1991-01-01

Half of Illinois' 38 million acres were planted in corn and soybeans in 1988. On the 19 million acres planted in corn and soybeans, approximately 1 million tons of nitrogen fertilizer and 50 million pounds of pesticides were applied. Because groundwater is the water supply for over 90 percent of rural Illinois, the occurrence of agricultural chemicals in groundwater in Illinois is of interest to the agricultural community, the public, and regulatory agencies. The occurrence of agricultural chemicals in groundwater is well documented. However, the extent of this contamination still needs to be defined. This can be done by randomly sampling wells across a geographic area. Key elements of a random, water-well sampling program for regional groundwater quality include the overall statistical design of the program, definition of the sample population, selection of wells to be sampled, and analysis of survey results. These elements must be consistent with the purpose for conducting the program; otherwise, the program will not provide the desired information. The need to carefully design and conduct a sampling program becomes readily apparent when one considers the high cost of collecting and analyzing a sample. For a random sampling program conducted in Illinois, the key elements, as well as the limitations imposed by available information, are described.

A real-time spectrum acquisition system design based on quantum dots-quantum well detector

NASA Astrophysics Data System (ADS)

Zhang, S. H.; Guo, F. M.

2016-01-01

In this paper, we studied the structure characteristics of quantum dots-quantum well photodetector with response wavelength range from 400 nm to 1000 nm. It has the characteristics of high sensitivity, low dark current and the high conductance gain. According to the properties of the quantum dots-quantum well photodetectors, we designed a new type of capacitive transimpedence amplifier (CTIA) readout circuit structure with the advantages of adjustable gain, wide bandwidth and high driving ability. We have implemented the chip packaging between CTIA-CDS structure readout circuit and quantum dots detector and tested the readout response characteristics. According to the timing signals requirements of our readout circuit, we designed a real-time spectral data acquisition system based on FPGA and ARM. Parallel processing mode of programmable devices makes the system has high sensitivity and high transmission rate. In addition, we realized blind pixel compensation and smoothing filter algorithm processing to the real time spectrum data by using C++. Through the fluorescence spectrum measurement of carbon quantum dots and the signal acquisition system and computer software system to realize the collection of the spectrum signal processing and analysis, we verified the excellent characteristics of detector. It meets the design requirements of quantum dot spectrum acquisition system with the characteristics of short integration time, real-time and portability.

Making intelligent systems team players: Additional case studies

NASA Technical Reports Server (NTRS)

Malin, Jane T.; Schreckenghost, Debra L.; Rhoads, Ron W.

1993-01-01

Observations from a case study of intelligent systems are reported as part of a multi-year interdisciplinary effort to provide guidance and assistance for designers of intelligent systems and their user interfaces. A series of studies were conducted to investigate issues in designing intelligent fault management systems in aerospace applications for effective human-computer interaction. The results of the initial study are documented in two NASA technical memoranda: TM 104738 Making Intelligent Systems Team Players: Case Studies and Design Issues, Volumes 1 and 2; and TM 104751, Making Intelligent Systems Team Players: Overview for Designers. The objective of this additional study was to broaden the investigation of human-computer interaction design issues beyond the focus on monitoring and fault detection in the initial study. The results of this second study are documented which is intended as a supplement to the original design guidance documents. These results should be of interest to designers of intelligent systems for use in real-time operations, and to researchers in the areas of human-computer interaction and artificial intelligence.

D-optimal experimental designs to test for departure from additivity in a fixed-ratio mixture ray.

PubMed

Coffey, Todd; Gennings, Chris; Simmons, Jane Ellen; Herr, David W

2005-12-01

Traditional factorial designs for evaluating interactions among chemicals in a mixture may be prohibitive when the number of chemicals is large. Using a mixture of chemicals with a fixed ratio (mixture ray) results in an economical design that allows estimation of additivity or nonadditive interaction for a mixture of interest. This methodology is extended easily to a mixture with a large number of chemicals. Optimal experimental conditions can be chosen that result in increased power to detect departures from additivity. Although these designs are used widely for linear models, optimal designs for nonlinear threshold models are less well known. In the present work, the use of D-optimal designs is demonstrated for nonlinear threshold models applied to a fixed-ratio mixture ray. For a fixed sample size, this design criterion selects the experimental doses and number of subjects per dose level that result in minimum variance of the model parameters and thus increased power to detect departures from additivity. An optimal design is illustrated for a 2:1 ratio (chlorpyrifos:carbaryl) mixture experiment. For this example, and in general, the optimal designs for the nonlinear threshold model depend on prior specification of the slope and dose threshold parameters. Use of a D-optimal criterion produces experimental designs with increased power, whereas standard nonoptimal designs with equally spaced dose groups may result in low power if the active range or threshold is missed.

A design study for the addition of higher order parametric discrete elements to NASTRAN

NASA Technical Reports Server (NTRS)

Stanton, E. L.

1972-01-01

The addition of discrete elements to NASTRAN poses significant interface problems with the level 15.1 assembly modules and geometry modules. Potential problems in designing new modules for higher-order parametric discrete elements are reviewed in both areas. An assembly procedure is suggested that separates grid point degrees of freedom on the basis of admissibility. New geometric input data are described that facilitate the definition of surfaces in parametric space.

Data related to the experimental design for powder bed binder jetting additive manufacturing of silicone.

PubMed

Liravi, Farzad; Vlasea, Mihaela

2018-06-01

The data included in this article provides additional supporting information on our recent publication (Liravi et al., 2018 [1]) on a novel hybrid additive manufacturing (AM) method for fabrication of three-dimensional (3D) structures from silicone powder. A design of experiments (DoE) study has been carried out to optimize the geometrical fidelity of AM-made parts. This manuscript includes the details of a multi-level factorial DOE and the response optimization results. The variation in the temperature of powder-bed when exposed to heat is plotted as well. Furthermore, the effect of blending ratio of two parts of silicone binder on its curing speed was investigated by conducting DSC tests on a silicone binder with 100:2 precursor to curing agent ratio. The hardness of parts fabricated with non-optimum printing conditions are included and compared.

Design and Installation of Monitoring Wells Guidance

EPA Pesticide Factsheets

EPA Region 4 Science and Ecosystem Support Division (SESD) document, from Feb. 18, 2008, that describes procedures, methods, and considerations when designing and installing groundwater monitoring wells to be used for collection of groundwater samples.

Computer Graphics-aided systems analysis: application to well completion design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Detamore, J.E.; Sarma, M.P.

1985-03-01

The development of an engineering tool (in the form of a computer model) for solving design and analysis problems related with oil and gas well production operations is discussed. The development of the method is based on integrating the concepts of ''Systems Analysis'' with the techniques of ''Computer Graphics''. The concepts behind the method are very general in nature. This paper, however, illustrates the application of the method in solving gas well completion design problems. The use of the method will save time and improve the efficiency of such design and analysis problems. The method can be extended to othermore » design and analysis aspects of oil and gas wells.« less

Composite Gypsum Binders with Silica-containing Additives

NASA Astrophysics Data System (ADS)

Chernysheva, N. V.; Lesovik, V. S.; Drebezgova, M. Yu; Shatalova, S. V.; Alaskhanov, A. H.

2018-03-01

New types of fine mineral additives are proposed for designing water-resistant Composite Gypsum Binders (CGB); these additives significantly differ from traditional quartz feed: wastes from wet magnetic separation of Banded Iron Formation (BIF WMS waste), nanodispersed silica powder (NSP), chalk. Possibility of their combined use has been studied as well.

Effect of Additives on Green Sand Molding Properties using Design of Experiments and Taguchi's Quality Loss Function - An Experimental Study

NASA Astrophysics Data System (ADS)

Desai, Bhagyashree; Mokashi, Pavani; Anand, R. L.; Burli, S. B.; Khandal, S. V.

2016-09-01

The experimental study aims to underseek the effect of various additives on the green sand molding properties as a particular combination of additives could yield desired sand properties. The input parameters (factors) selected were water and powder (Fly ash, Coconut shell and Tamarind) in three levels. Experiments were planned using design of experiments (DOE). On the basis of plans, experiments were conducted to understand the behavior of sand mould properties such as compression strength, shear strength, permeability number with various additives. From the experimental results it could be concluded that the factors have significant effect on the sand properties as P-value found to be less than 0.05 for all the cases studied. The optimization based on quality loss function was also performed. The study revealed that the quality loss associated with the tamarind powder was lesser compared to other additives selected for the study. The optimization based on quality loss function and the parametric analysis using ANOVA suggested that the tamarind powder of 8 gm per Kg of molding sand and moisture content of 7% yield better properties to obtain sound castings.

Design for Additive Bio-Manufacturing: From Patient-Specific Medical Devices to Rationally Designed Meta-Biomaterials.

PubMed

Zadpoor, Amir A

2017-07-25

Recent advances in additive manufacturing (AM) techniques in terms of accuracy, reliability, the range of processable materials, and commercial availability have made them promising candidates for production of functional parts including those used in the biomedical industry. The complexity-for-free feature offered by AM means that very complex designs become feasible to manufacture, while batch-size-indifference enables fabrication of fully patient-specific medical devices. Design for AM (DfAM) approaches aim to fully utilize those features for development of medical devices with substantially enhanced performance and biomaterials with unprecedented combinations of favorable properties that originate from complex geometrical designs at the micro-scale. This paper reviews the most important approaches in DfAM particularly those applicable to additive bio-manufacturing including image-based design pipelines, parametric and non-parametric designs, metamaterials, rational and computationally enabled design, topology optimization, and bio-inspired design. Areas with limited research have been identified and suggestions have been made for future research. The paper concludes with a brief discussion on the practical aspects of DfAM and the potential of combining AM with subtractive and formative manufacturing processes in so-called hybrid manufacturing processes.

Design for Additive Bio-Manufacturing: From Patient-Specific Medical Devices to Rationally Designed Meta-Biomaterials

PubMed Central

Zadpoor, Amir A.

2017-01-01

Recent advances in additive manufacturing (AM) techniques in terms of accuracy, reliability, the range of processable materials, and commercial availability have made them promising candidates for production of functional parts including those used in the biomedical industry. The complexity-for-free feature offered by AM means that very complex designs become feasible to manufacture, while batch-size-indifference enables fabrication of fully patient-specific medical devices. Design for AM (DfAM) approaches aim to fully utilize those features for development of medical devices with substantially enhanced performance and biomaterials with unprecedented combinations of favorable properties that originate from complex geometrical designs at the micro-scale. This paper reviews the most important approaches in DfAM particularly those applicable to additive bio-manufacturing including image-based design pipelines, parametric and non-parametric designs, metamaterials, rational and computationally enabled design, topology optimization, and bio-inspired design. Areas with limited research have been identified and suggestions have been made for future research. The paper concludes with a brief discussion on the practical aspects of DfAM and the potential of combining AM with subtractive and formative manufacturing processes in so-called hybrid manufacturing processes. PMID:28757572

Do you have a well-designed organization?

PubMed

Goold, Michael; Campbell, Andrew

2002-03-01

For most companies, organization design is neither a science nor an art; it's an oxymoron. Organizational structures evolve in fits and starts, shaped more by politics than by policies. Although most executives can sense when their organization designs are not working well, few take meaningful action, partly because they lack a practical framework to guide them. The authors of this article provide just such a framework; they present nine tests that can be used to either evaluate an existing organization design or create a new one. Four "fit" tests offer an initial screen: The market advantage test asks whether a design directs sufficient management attention to the company's sources of competitive advantage; the parenting advantage test determines whether the design gives enough attention to the corporate-level activities that provide real value to the company; the people test shows whether the design reflects the employees' strengths; and the feasibility test looks at constraints that may impede implementation. Five "good design" tests can help a company refine its prospective design. The specialist cultures test ensures that there's sufficient insulation for units that need to be different from the prevailing culture; the difficult-links test determines whether a design offers solutions for potentially problematic unit-to-unit links; the redundant-hierarchy test asks whether the design has too many parent levels; the accountability test looks at whether every unit has suitable controls; and the flexibility test ensures that the design lets the company adapt to change. Once a design is altered, the tests should be repeated. Organizational decisions are inevitably complex, and tweaking one part of the design may produce unanticipated consequences elsewhere.

Maintain and Regain Well Clear: Maneuver Guidance Designs for Pilots Performing the Detect-and-Avoid Task

NASA Technical Reports Server (NTRS)

Monk, Kevin J.; Roberts, Zachary

2017-01-01

In order to support the future expansion and integration of Unmanned Aircraft Systems (UAS), ongoing research efforts have sought to produce findings that inform the minimum display information elements required for acceptable UAS pilot response times and traffic avoidance. Previous simulations have revealed performance benefits associated with DAA displays containing predictive information and suggestive maneuver guidance tools in the form of banding. The present study investigated the impact of various maneuver guidance display configurations on detect-and-avoid (DAA) task performance in a simulated airspace environment. UAS pilots ability to maintain DAA well clear was compared between displays with either the presence or absence of green DAA bands, which indicated conflict-free flight regions. Additional display comparisons assessed pilots ability to regain DAA well clear with two different guidance presentations designed to aid in DAA well clear recovery during critical encounters. Performance implications and display considerations for future UAS DAA systems are discussed.

A regularized variable selection procedure in additive hazards model with stratified case-cohort design.

PubMed

Ni, Ai; Cai, Jianwen

2018-07-01

Case-cohort designs are commonly used in large epidemiological studies to reduce the cost associated with covariate measurement. In many such studies the number of covariates is very large. An efficient variable selection method is needed for case-cohort studies where the covariates are only observed in a subset of the sample. Current literature on this topic has been focused on the proportional hazards model. However, in many studies the additive hazards model is preferred over the proportional hazards model either because the proportional hazards assumption is violated or the additive hazards model provides more relevent information to the research question. Motivated by one such study, the Atherosclerosis Risk in Communities (ARIC) study, we investigate the properties of a regularized variable selection procedure in stratified case-cohort design under an additive hazards model with a diverging number of parameters. We establish the consistency and asymptotic normality of the penalized estimator and prove its oracle property. Simulation studies are conducted to assess the finite sample performance of the proposed method with a modified cross-validation tuning parameter selection methods. We apply the variable selection procedure to the ARIC study to demonstrate its practical use.

Design of systems for productivity and well being.

PubMed

Edwards, Kasper; Jensen, Per Langaa

2014-01-01

It has always been an ambition within the ergonomic profession to ensure that design or redesign of production systems consider both productivity and employee well being, but there are many approaches to how to achieve this. This paper identifies the basic issues to be addressed in light of some research activities at DTU, especially by persons responsible for facilitating design processes. Four main issues must be addressed: (1) determining the limits and scope of the system to be designed; (2) identifying stakeholders related to the system and their role in the system design; (3) handling the process' different types of knowledge; and (4) emphasizing that performance management systems, key performance indicators (KPIs), and leadership are also part of the system design and must be given attention. With the examples presented, we argue that knowledge does exist to help system design facilitators address these basic issues. Copyright © 2013. Published by Elsevier Ltd.

Expanding the Design Space: Forging the Transition from 3D Printing to Additive Manufacturing

NASA Astrophysics Data System (ADS)

Amend, Matthew

The synergy of Additive Manufacturing and Computational Geometry has the potential to radically expand the "design space" of solutions available to designers. Additive Manufacturing (AM) is capable of fabricating objects that are highly complex both in geometry and material properties. However, the introduction of any new technology can have a disruptive effect on established design practices and organizations. Before "Design for Additive Manufacturing" (DFAM) is a commonplace means of producing objects employed in "real world" products, appropriate design knowledge must be sufficiently integrated within industry. First, materials suited to additive manufacturing methods must be developed to satisfy existing industry standards and specifications, or new standards must be developed. Second, a new class of design representation (CAD) tools will need to be developed. Third, designers and design organizations will need to develop strategies for employing such tools. This thesis describes three DFAM exercises intended to demonstrate the potential for innovative design when using advanced additive materials, tools, and printers. These design exercises included 1) a light-weight composite layup mold developed with topology optimization, 2) a low-pressure fluid duct enhanced with an external lattice structure, and 3) an airline seat tray designed using a non-uniform lattice structure optimized with topology optimization.

Base Stabilization Guidance and Additive Selection for Pavement Design and Rehabilitation

DOT National Transportation Integrated Search

2017-12-01

Significant improvements have been made in base stabilization practice that include design specifications and methodology, experience with the selection of stabilizing additives, and equipment for distribution and uniform blending of additives. For t...

Wood lens design philosophy based on a binary additive manufacturing technique

NASA Astrophysics Data System (ADS)

Marasco, Peter L.; Bailey, Christopher

2016-04-01

Using additive manufacturing techniques in optical engineering to construct a gradient index (GRIN) optic may overcome a number of limitations of GRIN technology. Such techniques are maturing quickly, yielding additional design degrees of freedom for the engineer. How best to employ these degrees of freedom is not completely clear at this time. This paper describes a preliminary design philosophy, including assumptions, pertaining to a particular printing technique for GRIN optics. It includes an analysis based on simulation and initial component measurement.

Structural Mass Saving Potential of a 5-MW Direct-Drive Generator Designed for Additive Manufacturing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sethuraman, Latha; Fingersh, Lee J; Dykes, Katherine L

As wind turbine blade diameters and tower height increase to capture more energy in the wind, higher structural loads results in more structural support material increasing the cost of scaling. Weight reductions in the generator transfer to overall cost savings of the system. Additive manufacturing facilitates a design-for-functionality approach, thereby removing traditional manufacturing constraints and labor costs. The most feasible additive manufacturing technology identified for large, direct-drive generators in this study is powder-binder jetting of a sand cast mold. A parametric finite element analysis optimization study is performed, optimizing for mass and deformation. Also, topology optimization is employed for eachmore » parameter-optimized design.The optimized U-beam spoked web design results in a 24 percent reduction in structural mass of the rotor and 60 percent reduction in radial deflection.« less

Relearning To Teach Arithmetic Addition and Subtraction: A Teacher's Study Guide.

ERIC Educational Resources Information Center

Russell, Susan Jo

This package features videotapes and a study guide that are designed to help teachers revisit the operations of addition and subtraction and consider how students can develop meaningful approaches to these operations. The study guides' sessions are on addition, subtraction, the teacher's role, and goals for students and teachers. The readings in…

DETAIL OF PLAQUE WITH ADDITIONAL DESIGN AND CONSTRUCTION INFORMATION, SOUTHEAST ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

DETAIL OF PLAQUE WITH ADDITIONAL DESIGN AND CONSTRUCTION INFORMATION, SOUTHEAST ABUTMENT - Connecticut Avenue Bridge, Spans Rock Creek & Potomac Parkway at Connecticut Avenue, Washington, District of Columbia, DC

Analysis and design of trial well mooring in deepwater of the South China Sea

NASA Astrophysics Data System (ADS)

Guo, Yongfeng; Ji, Shaojun; Tang, Changquan; Li, Jiansong; Zhong, Huiquan; Ian, Ong Chin Yam

2012-06-01

Mooring systems play an important role for semi-submersible rigs that drill in deepwater. A detailed analysis was carried out on the mooring of a semi-submersible rig that conducted a trial well drilling at a deepwater location in the South China Sea in 2009. The rig was 30 years old and had a shallow platform with a designed maximum operating water depth of 457 m. Following the mooring analysis, a mooring design was given that requires upgrading of the rig's original mooring system. The upgrade included several innovations, such as installing eight larger anchors, i.e. replacing the original anchors and inserting an additional 600 m of steel wires with the existing chains. All this was done to enhance the mooring capability of the rig in order for the rig to be held in position to conduct drilling at a water depth of 476 m. The overall duration of the drilling was 50 days and the upgraded mooring system proved to be efficient in achieving the goal of keeping the rig stationary while it was drilling the trial well in the South China Sea. This successful campaign demonstrates that an older semi-submersible rig can take on drilling in deep water after careful design and proper upgrading and modification to the original mooring system.

19 CFR 115.7 - Designation of additional Certifying Authorities.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 19 Customs Duties 1 2011-04-01 2011-04-01 false Designation of additional Certifying Authorities. 115.7 Section 115.7 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS...

19 CFR 115.7 - Designation of additional Certifying Authorities.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 19 Customs Duties 1 2014-04-01 2014-04-01 false Designation of additional Certifying Authorities. 115.7 Section 115.7 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS...

19 CFR 115.7 - Designation of additional Certifying Authorities.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false Designation of additional Certifying Authorities. 115.7 Section 115.7 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS...

19 CFR 115.7 - Designation of additional Certifying Authorities.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 19 Customs Duties 1 2013-04-01 2013-04-01 false Designation of additional Certifying Authorities. 115.7 Section 115.7 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS...

19 CFR 115.7 - Designation of additional Certifying Authorities.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 19 Customs Duties 1 2012-04-01 2012-04-01 false Designation of additional Certifying Authorities. 115.7 Section 115.7 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS...

10 CFR 60.133 - Additional design criteria for the underground facility.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Additional design criteria for the underground facility. 60.133 Section 60.133 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DISPOSAL OF HIGH-LEVEL RADIOACTIVE WASTES IN GEOLOGIC REPOSITORIES Technical Criteria Design Criteria for the Geologic Repository...

Design and Testing of a Hall Effect Thruster with Additively Manufactured Components

NASA Astrophysics Data System (ADS)

Hopping, Ethan

The UAH-78AM is a low-power Hall effect thruster developed at the University of Alabama in Huntsville to study the application of low-cost additive manufacturing in the design and fabrication of Hall thrusters. The goal of this project is to assess the feasibility of using unconventional materials to produce a low-cost functioning Hall effect thruster and consider how additive manufacturing can expand the design space and provide other benefits. The thruster features channel walls and a propellant distributor that were manufactured using 3D printing with a variety of materials including ABS, ULTEM, and glazed ceramic. A version of the thruster was tested at NASA Glenn Research Center to obtain performance metrics and to validate the ability of the thruster to produce thrust and sustain a discharge. The design of the thruster and the transient performance measurements are presented here. Measured thrust ranged from 17.2 mN to 30.4 mN over a discharge power of 280 W to 520 W with an anode Isp range of 870 s to 1450 s. Temperature limitations of materials used for the channel walls and propellant distributor limit the ability to run the thruster at thermal steady-state. While the current thruster design is not yet ready for continuous operation, revisions to the device that could enable longer duration tests are discussed.

Workplace design contributions to mental health and well-being.

PubMed

Veitch, Jennifer A

2011-01-01

People spend much of their waking time in their workplaces (approximately 33% on a weekly basis), which raises the possibility that the conditions they experience at work influence their health and well-being. The workplace design literature has given scant attention to mental health outcomes, instead focusing on healthy populations. Conversely, the mental health literature gives scant attention to the potential contribution of workplace design in preventing mental health problems; nor does it provide much insight into facilitating return to work. Taken together, however, the literature does suggest both lines of research and possible interventions. Existing knowledge proposes that workplace design can influence mental health via the effects of light exposure on circadian regulation, social behaviour and affect; the effects of aesthetic judgement on at-work mood and physical well-being and at-home sleep quality; access to nature and recovery from stressful experiences; and privacy regulation and stimulus control. This paper includes a short review of the literature in this area, proposals for new research directions and consideration of the implications of this information on the design choices made by business owners, designers and facility managers. Providing suitable working conditions for all employees avoids stigmatizing employees who have mental health problems, while facilitating prevention and return to work among those who do. Copyright © 2011 Longwoods Publishing.

76 FR 7241 - Additional Designation of Entities Pursuant to Executive Order 13382

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-09

... DEPARTMENT OF THE TREASURY Office of Foreign Assets Control Additional Designation of Entities... 4 newly-designated entities and one newly-designated individual whose property and interests in... of the 4 entities and one individual identified in this notice pursuant to Executive Order 13382 is...

75 FR 51876 - Additional Designation of Entities Pursuant to Executive Order 13382

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-23

... DEPARTMENT OF THE TREASURY Office of Foreign Assets Control Additional Designation of Entities... 3 newly-designated entities whose property and interests in property are blocked pursuant to... Their Supporters.'' DATES: The designation by the Director of OFAC of the 3 entities identified in this...

76 FR 40772 - Additional Designation of Entities Pursuant to Executive Order 13382

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-11

... DEPARTMENT OF THE TREASURY Office of Foreign Assets Control Additional Designation of Entities... 2 newly-designated entities whose property and interests in property are blocked pursuant to... Their Supporters.'' DATES: The designation by the Director of OFAC of the 2 entities identified in this...

75 FR 70352 - Additional Designation of Entities Pursuant to Executive Order 13382

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-17

... DEPARTMENT OF THE TREASURY Office of Foreign Assets Control Additional Designation of Entities... 37 newly-designated entities and 5 newly-designated individuals whose property and interests in... of the 37 entities and 5 individuals identified in this notice pursuant to Executive Order 13382 is...

76 FR 12414 - Additional Designation of Entity Pursuant to Executive Order 13382

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-07

... DEPARTMENT OF THE TREASURY Office of Foreign Assets Control Additional Designation of Entity... newly-designated entity whose property and interests in property are blocked pursuant to Executive Order... Supporters.'' DATES: The designation by the Director of OFAC of the 1 entity identified in this notice...

77 FR 35114 - Additional Designation of Entity Pursuant to Executive Order 13382

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-12

... DEPARTMENT OF THE TREASURY Office of Foreign Assets Control Additional Designation of Entity... newly-designated entity whose property and interests in property are blocked pursuant to Executive Order... Supporters.'' DATES: The designation by the Director of OFAC of the 1 entity identified in this notice...

Design of an Orthopedic Product by Using Additive Manufacturing Technology: The Arm Splint.

PubMed

Blaya, Fernando; Pedro, Pilar San; Silva, Julia López; D'Amato, Roberto; Heras, Enrique Soriano; Juanes, Juan Antonio

2018-02-05

The traditional fabrication process of custom-made splints has hardly undergone any progress since the beginning of its use at the end of the eighteenth century. New manufacturing techniques and the new materials can help to modernize this treatment method of fractures. The use of Additive Manufacturing has been proposed in recent years as an alternative process for the manufacture of splints and there has been an increase in public awareness and exploration. For this reason, in this study a splint model printed in 3D, that replaces the deficiencies of the cast maintaining its virtues, has been proposed. The proposed methodology is based on three-dimensional digitalization techniques and 3D modeling with reverse engineering software. The work integrates different scientific disciplines to achieve its main goal: to improve life quality of the patient. In addition, the splint has been designed based on the principles of sustainable development. The design of splint is made of Polycarbonate by technique of Additive Manufacturing with fused deposition manufacturing, and conceived with organic shapes, customizing openings and closing buttons with rubber. In this preliminary study the final result is a prototype of the 3D printed arm splint in a reduced scale by using PLA as material.

Estimation of a partially linear additive model for data from an outcome-dependent sampling design with a continuous outcome

PubMed Central

Tan, Ziwen; Qin, Guoyou; Zhou, Haibo

2016-01-01

Outcome-dependent sampling (ODS) designs have been well recognized as a cost-effective way to enhance study efficiency in both statistical literature and biomedical and epidemiologic studies. A partially linear additive model (PLAM) is widely applied in real problems because it allows for a flexible specification of the dependence of the response on some covariates in a linear fashion and other covariates in a nonlinear non-parametric fashion. Motivated by an epidemiological study investigating the effect of prenatal polychlorinated biphenyls exposure on children's intelligence quotient (IQ) at age 7 years, we propose a PLAM in this article to investigate a more flexible non-parametric inference on the relationships among the response and covariates under the ODS scheme. We propose the estimation method and establish the asymptotic properties of the proposed estimator. Simulation studies are conducted to show the improved efficiency of the proposed ODS estimator for PLAM compared with that from a traditional simple random sampling design with the same sample size. The data of the above-mentioned study is analyzed to illustrate the proposed method. PMID:27006375

A Wellness Mobile Application for Smart Health: Pilot Study Design and Results.

PubMed

Sannino, Giovanna; Forastiere, Manolo; De Pietro, Giuseppe

2017-03-17

Wellness is one of the main factors crucial in the avoidance of illness or disease. Experience has shown that healthy lifestyle programs are an important strategy to prevent the major shared risk factors for many diseases including cardiovascular diseases, strokes, diabetes, obesity, and hypertension. Within the ambit of the Smart Health 2.0 project, a Wellness App has been developed which has the aim of providing people with something similar to a personal trainer. This Wellness App is able to gather information about the subject, to classify her/him by evaluating some of her/his specific characteristics (physical parameters and lifestyle) and to make personal recommendations to enhance her/his well-being. The application can also give feedback on the effectiveness of the specified characteristics by monitoring their evolution over time, and can provide a positive incentive to stimulate the subject to achieve her/his wellness goals. In this paper, we present a pilot study conducted in Calabria, a region of Italy, aimed at an evaluation of the validity, usability, and navigability of the app, and of people's level of satisfaction with it. The preliminary results show an average score of 77.16 for usability and of 76.87 for navigability, with an improvement of the Wellness Index with a significance average of 95% and of the Mediterranean Adequacy Index with a significance average of as high as 99%.

Personality, work characteristics, and employee well-being: a longitudinal analysis of additive and moderating effects.

PubMed

Houkes, Inge; Janssen, Peter P M; de Jonge, Jan; Bakker, Arnold B

2003-01-01

This study tested the longitudinal influence of personality (measured by the characteristics growth need strength, negative affectivity [NA], and upward striving) on 3 psychological outcomes (intrinsic work motivation, emotional exhaustion, and turnover intention), using a pattern of specific relationships between work characteristics and these outcomes as a framework. The study hypotheses were tested in a multioccupational sample consisting of bank employees and teachers, using a 2-wave panel design with a 1-year time interval and structural equation modeling. NA had a cross-lagged direct and additive relationship with emotional exhaustion and also moderated the relationship between Time 1 workload and Time 2 emotional exhaustion. The authors concluded that NA may have multiple effects on emotional exhaustion that persist over time.

Applying Additive Manufacturing to a New Liquid Oxygen Turbopump Design

NASA Technical Reports Server (NTRS)

O’Neal, T. Derek

2016-01-01

A liquid oxygen turbopump has been designed at Marshall Space Flight Center as part of the in-house, Advanced Manufacturing Demonstrator Engine (AMDE) project. Additive manufacturing, specifically direct metal laser sintering (DMLS) of Inconel 718, is used for 77% of the parts by mass. These parts include the impeller, turbine components, and housings. This paper discusses the impacts of the DMLS fabrication technique on the design of the turbopump and lessons learned during DMLS hardware fabrication and material testing.

A Wellness Mobile Application for Smart Health: Pilot Study Design and Results

PubMed Central

Sannino, Giovanna; Forastiere, Manolo; De Pietro, Giuseppe

2017-01-01

Wellness is one of the main factors crucial in the avoidance of illness or disease. Experience has shown that healthy lifestyle programs are an important strategy to prevent the major shared risk factors for many diseases including cardiovascular diseases, strokes, diabetes, obesity, and hypertension. Within the ambit of the Smart Health 2.0 project, a Wellness App has been developed which has the aim of providing people with something similar to a personal trainer. This Wellness App is able to gather information about the subject, to classify her/him by evaluating some of her/his specific characteristics (physical parameters and lifestyle) and to make personal recommendations to enhance her/his well-being. The application can also give feedback on the effectiveness of the specified characteristics by monitoring their evolution over time, and can provide a positive incentive to stimulate the subject to achieve her/his wellness goals. In this paper, we present a pilot study conducted in Calabria, a region of Italy, aimed at an evaluation of the validity, usability, and navigability of the app, and of people’s level of satisfaction with it. The preliminary results show an average score of 77.16 for usability and of 76.87 for navigability, with an improvement of the Wellness Index with a significance average of 95% and of the Mediterranean Adequacy Index with a significance average of as high as 99%. PMID:28304332

Strengthening the Regression Discontinuity Design Using Additional Design Elements: A Within-Study Comparison

ERIC Educational Resources Information Center

Wing, Coady; Cook, Thomas D.

2013-01-01

The sharp regression discontinuity design (RDD) has three key weaknesses compared to the randomized clinical trial (RCT). It has lower statistical power, it is more dependent on statistical modeling assumptions, and its treatment effect estimates are limited to the narrow subpopulation of cases immediately around the cutoff, which is rarely of…

30 CFR 250.413 - What must my description of well drilling design criteria address?

Code of Federal Regulations, 2013 CFR

2013-07-01

... design criteria address? 250.413 Section 250.413 Mineral Resources BUREAU OF SAFETY AND ENVIRONMENTAL... of well drilling design criteria address? Your description of well drilling design criteria must... the completion phases, including the anticipated surface pressure used for designing the production...

30 CFR 250.413 - What must my description of well drilling design criteria address?

Code of Federal Regulations, 2012 CFR

2012-07-01

... design criteria address? 250.413 Section 250.413 Mineral Resources BUREAU OF SAFETY AND ENVIRONMENTAL... of well drilling design criteria address? Your description of well drilling design criteria must... the completion phases, including the anticipated surface pressure used for designing the production...

30 CFR 250.413 - What must my description of well drilling design criteria address?

Code of Federal Regulations, 2014 CFR

2014-07-01

... design criteria address? 250.413 Section 250.413 Mineral Resources BUREAU OF SAFETY AND ENVIRONMENTAL... of well drilling design criteria address? Your description of well drilling design criteria must... the completion phases, including the anticipated surface pressure used for designing the production...

30 CFR 250.413 - What must my description of well drilling design criteria address?

Code of Federal Regulations, 2011 CFR

2011-07-01

... design criteria address? 250.413 Section 250.413 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT... must my description of well drilling design criteria address? Your description of well drilling design... drilling and the completion phases, including the anticipated surface pressure used for designing the...

Adolescents’ Interpretation of the Concept of Wellness: A Qualitative Study

PubMed Central

Ahanonu, Ezihe Loretta; Jooste, Karien

2016-01-01

Introduction: This study sought to explore and describe the interpretation which adolescents ascribe to the term wellness at a selected high school in the Western Cape Province of South Africa. Methods: A qualitative research design was utilized. Nine focus-group discussions were conducted among 58 adolescents. Sample was selected purposefully and collected data was analyzed using open coding. Results: Findings reflected adolescents’ interpretations of the term wellness in the realm of holistic well-being transcending the nonexistence of illness or sickness in the body. The interpretations given include: healthy living which embrace eating enough nutritious foods, exercising regularly and being actively involved in physical activities; practicing self-care habits such as personal hygiene and grooming; well-being of the mind (psychological, emotional); having a balanced personality and interpersonal processes; being focused and goal directed and spiritual well-being. Conclusion: It is imperative to consider adolescents’ understandings of wellness when planning, designing, implementing and evaluating adolescent wellness programs. PMID:28032078

76 FR 52384 - Designation of Additional Entities Pursuant to Executive Order 13405

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-22

... DEPARTMENT OF THE TREASURY Office of Foreign Assets Control Designation of Additional Entities... Assets Control (``OFAC'') is publishing the names of four newly-designated entities whose property and... the Director of OFAC of the four entities identified in this notice, pursuant to Executive [[Page...

77 FR 54946 - Additional Designations of Individuals Pursuant to Executive Order 13581

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-06

... DEPARTMENT OF THE TREASURY Office of Foreign Assets Control Additional Designations of Individuals... the names of five individuals whose property and interests in property have been blocked pursuant to... Order''). DATES: The designation by the Director of OFAC of the five individuals identified in this...

IT-based wellness tools for older adults: Design concepts and feedback.

PubMed

Joe, Jonathan; Hall, Amanda; Chi, Nai-Ching; Thompson, Hilaire; Demiris, George

2018-03-01

To explore older adults' preferences regarding e-health applications through use of generated concepts that inform wellness tool design. The 6-8-5 method and affinity mapping were used to create e-health design ideas that were translated into storyboards and scenarios. Focus groups were conducted to obtain feedback on the prototypes and included participant sketching. A qualitative analysis of the focus groups for emerging themes was conducted, and sketches were analyzed. Forty-three older adults participated in six focus group sessions. The majority of participants found the wellness tools useful. Preferences included features that supported participants in areas of unmet needs, such as ability to find reliable health information, cognitive training, or maintaining social ties. Participants favored features such as use of voice navigation, but were concerned over cost and the need for technology skills and access. Sketches reinforced these wants, including portability, convenience, and simplicity. Several factors were found to increase the desirability of such devices including convenient access to their health and health information, a simple, accessible interface, and support for memory issues. Researchers and designers should incorporate the feedback of older adults regarding wellness tools, so that future designs meet the needs of older adults.

The Neighbourhood Effects on Health and Well-being (NEHW) study.

PubMed

O'Campo, Patricia; Wheaton, Blair; Nisenbaum, Rosane; Glazier, Richard H; Dunn, James R; Chambers, Catharine

2015-01-01

Many cross-sectional studies of neighbourhood effects on health do not employ strong study design elements. The Neighbourhood Effects on Health and Well-being (NEHW) study, a random sample of 2412 English-speaking Toronto residents (age 25-64), utilises strong design features for sampling neighbourhoods and individuals, characterising neighbourhoods using a variety of data sources, measuring a wide range of health outcomes, and for analysing cross-level interactions. We describe here methodological issues that shaped the design and analysis features of the NEHW study to ensure that, while a cross-sectional sample, it will advance the quality of evidence emerging from observational studies. Copyright © 2014 The Authors. Published by Elsevier Ltd.. All rights reserved.

Adsorption of molecular additive onto lead halide perovskite surfaces: A computational study on Lewis base thiophene additive passivation

NASA Astrophysics Data System (ADS)

Zhang, Lei; Yu, Fengxi; Chen, Lihong; Li, Jingfa

2018-06-01

Organic additives, such as the Lewis base thiophene, have been successfully applied to passivate halide perovskite surfaces, improving the stability and properties of perovskite devices based on CH3NH3PbI3. Yet, the detailed nanostructure of the perovskite surface passivated by additives and the mechanisms of such passivation are not well understood. This study presents a nanoscopic view on the interfacial structure of an additive/perovskite interface, consisting of a Lewis base thiophene molecular additive and a lead halide perovskite surface substrate, providing insights on the mechanisms that molecular additives can passivate the halide perovskite surfaces and enhance the perovskite-based device performance. Molecular dynamics study on the interactions between water molecules and the perovskite surfaces passivated by the investigated additive reveal the effectiveness of employing the molecular additives to improve the stability of the halide perovskite materials. The additive/perovskite surface system is further probed via molecular engineering the perovskite surfaces. This study reveals the nanoscopic structure-property relationships of the halide perovskite surface passivated by molecular additives, which helps the fundamental understanding of the surface/interface engineering strategies for the development of halide perovskite based devices.

Environmental design, work, and well being: managing occupational stress through changes in the workplace environment.

PubMed

Heerwagen, J H; Heubach, J G; Montgomery, J; Weimer, W C

1995-09-01

The physical environment can be an important contributor to occupational stress. Factors that contribute to stress and other negative outcomes include: lack of control over the environment, distractions from coworkers, lack of privacy, noise, crowding, and environmental deprivations (such as lack of windows and aesthetic impoverishment). The design of "salutogenic" environments requires not only the elimination of negative stress inducing features, but also the addition of environmental enhancements, including such factors as increased personal control, contact with nature and daylight, aesthetically pleasing spaces, and spaces for relaxation alone or with others. Salutogenic environments also take into consideration positive psychosocial "fit," as well as functional fit between people and environments. At the heart of the current interest in the work environment are two major concerns: organizational productivity and employee well being.

Design, development, and evaluation of truck and bus driver wellness programs

DOT National Transportation Integrated Search

2000-06-01

In May 1997, the Federal Motor Carrier Safety Administration (FMCSA) began a research project to design, develop, and evaluate a model truck and bus driver wellness program. This wellness program was developed to provide a resource for addressing tru...

Designing SoTL Studies--Part II: Practicality

ERIC Educational Resources Information Center

Bartsch, Robert A.

2013-01-01

This chapter suggests solutions to common practical problems in designing SoTL studies. In addition, the advantages and disadvantages of different types of designs are discussed. [Part I available at EJ1029363.

The influence of bioaugmentation and biosurfactant addition on bioremediation efficiency of diesel-oil contaminated soil: feasibility during field studies.

PubMed

Szulc, Alicja; Ambrożewicz, Damian; Sydow, Mateusz; Ławniczak, Łukasz; Piotrowska-Cyplik, Agnieszka; Marecik, Roman; Chrzanowski, Łukasz

2014-01-01

The study focused on assessing the influence of bioaugmentation and addition of rhamnolipids on diesel oil biodegradation efficiency during field studies. Initial laboratory studies (measurement of emitted CO2 and dehydrogenase activity) were carried out in order to select the consortium for bioaugmentation as well as to evaluate the most appropriate concentration of rhamnolipids. The selected consortium consisted of following bacterial taxa: Aeromonas hydrophila, Alcaligenes xylosoxidans, Gordonia sp., Pseudomonas fluorescens, Pseudomonas putida, Rhodococcus equi, Stenotrophomonas maltophilia, Xanthomonas sp. It was established that the application of rhamnolipids at 150 mg/kg of soil was most appropriate in terms of dehydrogenase activity. Based on the obtained results, four treatment methods were designed and tested during 365 days of field studies: I) natural attenuation; II) addition of rhamnolipids; III) bioaugmentation; IV) bioaugmentation and addition of rhamnolipids. It was observed that bioaugmentation contributed to the highest diesel oil biodegradation efficiency, whereas the addition of rhamnolipids did not notably influence the treatment process. Copyright © 2013 Elsevier Ltd. All rights reserved.

Additional Remarks on Designing Category-Level Attributes for Discriminative Visual Recognition

DTIC Science & Technology

2013-01-01

Discriminative Visual Recognition ∗ Felix X. Yu†, Liangliang Cao§, Rogerio S. Feris§, John R. Smith§, Shih-Fu Chang† † Columbia University § IBM T. J...for Designing Category-Level Attributes for Dis- criminative Visual Recognition [3]. We first provide an overview of the proposed ap- proach in...2013 to 00-00-2013 4. TITLE AND SUBTITLE Additional Remarks on Designing Category-Level Attributes for Discriminative Visual Recognition 5a

Epidemiological study air disaster in Amsterdam (ESADA): study design.

PubMed

Slottje, Pauline; Huizink, Anja C; Twisk, Jos W R; Witteveen, Anke B; van der Ploeg, Henk M; Bramsen, Inge; Smidt, Nynke; Bijlsma, Joost A; Bouter, Lex M; van Mechelen, Willem; Smid, Tjabe

2005-05-30

In 1992, a cargo aircraft crashed into apartment buildings in Amsterdam, killing 43 victims and destroying 266 apartments. In the aftermath there were speculations about the cause of the crash, potential exposures to hazardous materials due to the disaster and the health consequences. Starting in 2000, the Epidemiological Study Air Disaster in Amsterdam (ESADA) aimed to assess the long-term health effects of occupational exposure to this disaster on professional assistance workers. Epidemiological study among all the exposed professional fire-fighters and police officers who performed disaster-related task(s), and hangar workers who sorted the wreckage of the aircraft, as well as reference groups of their non-exposed colleagues who did not perform any disaster-related tasks. The study took place, on average, 8.5 years after the disaster. Questionnaires were used to assess details on occupational exposure to the disaster. Health measures comprised laboratory assessments in urine, blood and saliva, as well as self-reported current health measures, including health-related quality of life, and various physical and psychological symptoms. In this paper we describe and discuss the design of the ESADA. The ESADA will provide additional scientific knowledge on the long-term health effects of technological disasters on professional workers.

A Case Study in Design Thinking Applied Through Aviation Mission Support Tactical Advancements for the Next Generation (TANG)

DTIC Science & Technology

2017-12-01

This is an examination of the research, execution, and follow- on developments supporting the Design Thinking event explored through Case Study ...research, execution, and follow- on developments supporting the Design Thinking event explored through case study methods. Additionally, the lenses of...total there have been two Naval Postgraduate School (NPS) case study theses on U.S. Navy innovation events as well as other works examining the

SRB ascent aerodynamic heating design criteria reduction study, volume 1

NASA Technical Reports Server (NTRS)

Crain, W. K.; Frost, C. L.; Engel, C. D.

1989-01-01

An independent set of solid rocket booster (SRB) convective ascent design environments were produced which would serve as a check on the Rockwell IVBC-3 environments used to design the ascent phase of flight. In addition, support was provided for lowering the design environments such that Thermal Protection System (TPS), based on conservative estimates, could be removed leading to a reduction in SRB refurbishment time and cost. Ascent convective heating rates and loads were generated at locations in the SRB where lowering the thermal environment would impact the TPS design. The ascent thermal environments are documented along with the wind tunnel/flight test data base used as well as the trajectory and environment generation methodology. Methodology, as well as, environment summaries compared to the 1980 Design and Rockwell IVBC-3 Design Environment are presented in this volume, 1.

Design, methodology, and baseline data of the Personalized Addition Lenses Clinical Trial (PACT)

PubMed Central

Yu, Xinping; Zhang, Binjun; Bao, Jinhua; Zhang, Junxiao; Wu, Ge; Xu, Jinling; Zheng, Jingwei; Drobe, Björn; Chen, Hao

2017-01-01

Abstract Background: The aim of this study was to describe the design, methods, and baseline characteristics of children enrolled in the Personalized Addition lenses Clinical Trial (PACT). PACT aims to test the myopia control efficacy of progressive addition lenses (PALs) with personalized addition values compared with standard (+2.00 D) addition PALs and single vision lenses (SVLs). Methods: PACT is a randomized, controlled, double-masked clinical trial. Two hundred eleven myopic Chinese children (7–12 years) were enrolled and randomized into 1 of the 3 following groups: personalized addition PALs; +2.00 addition PALs; and SVLs. Personalized addition values were determined based on the highest addition that satisfied Sheard criterion. Axial length and other biometric data were also recorded. Results: At baseline, no differences were found between the right and left eyes for any of the main parameters. The enrolled children were 9.7 ± 1.1 years’ old with cycloplegic autorefraction (right eye [OD]: −2.36 ± 0.64 D), near phoria (1.0 ± 5.0 prism diopter esophoria), lag of accommodation (1.40 ± 0.50 D) and axial length (OD: 24.58 ± 0.74 mm). The personalized addition values ranged from +0.75 to +3.00 (average ± SD: 2.19 ± 0.73 D). Conclusion: PACT is a clinical trial evaluating whether myopia progression in children can be slowed by wearing personalized addition PALs compared with fixed addition PALs and SVLs as measured by cycloplegic autorefraction and axial length. Baseline data were comparable with those of previous myopia control studies in children. Subjects will be followed up every 6 months for 2 years. PMID:28296722

Evaluating Intention and Effect: The Impact of Healthcare Facility Design on Patient and Staff Well-Being.

PubMed

Alvaro, Celeste; Wilkinson, Andrea J; Gallant, Sara N; Kostovski, Deyan; Gardner, Paula

2016-01-01

This post occupancy evaluation (POE) assessed the impact of architectural design on psychosocial well-being among patients and staff in the context of a new complex continuing care and rehabilitation facility. Departing from typical POEs, the hospital design intentions formed the theoretical basis to assess outcomes. Intentions included creating an environment of wellness; enhancing connection to the community, the city, and nature; enhancing opportunities for social interaction; and inspiring activity. A pretest-posttest quasi experiment, including quantitative surveys, assessed the impact of the building design on well-being outcomes across three facilities-the new hospital, the former hospital, and a comparison facility with a similar population. With the exception of connection to neighborhood (for patients) and opportunities to visit with others (for staff) and wayfinding (for patients and staff), impressions of the new hospital mirrored the design intentions relative to the former hospital and the comparison facility among patients and staff. Perceptions of improvement in mental health, self-efficacy in mobility, satisfaction, and interprofessional interactions were enhanced at the new hospital relative to the former hospital, whereas optimism, depressive symptoms, general well-being, burnout, and intention to quit did not vary. Interestingly, patients and staff with favorable impressions of the building design fared better on most well-being-related outcomes relative to those with less favorable impressions. Beyond the value of assessing the impact of the design intentions on outcomes, the approach used in this study would benefit evaluation strategies across a diversity of health and other public and large-scale buildings. © The Author(s) 2015.

Applying Additive Manufacturing to a New Liquid Oxygen Turbopump Design

NASA Technical Reports Server (NTRS)

O'Neal, Derek

2016-01-01

A liquid oxygen turbopump has been designed at Marshall Space Flight Center as part of the in-house, Advanced Manufacturing Demonstrator Engine (AMDE) project. Additive manufacturing, specifically direct metal laser sintering (DMLS) of Inconel 718, is used for 77% of the parts by mass. These parts include the impeller, turbine components, and housings. The near-net shape DMLS parts have been delivered and final machining is underway. Fabrication of the traditionally manufactured hardware is also proceeding. Testing in liquid oxygen is planned for Q2 of FY2017. This topic explores the design of the turbopump along with fabrication and material testing of the DMLS hardware.

47 CFR 54.202 - Additional requirements for Commission designation of eligible telecommunications carriers.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 3 2014-10-01 2014-10-01 false Additional requirements for Commission designation of eligible telecommunications carriers. 54.202 Section 54.202 Telecommunication FEDERAL... telecommunications carriers. (a) In order to be designated an eligible telecommunications carrier under section 214(e...

47 CFR 54.202 - Additional requirements for Commission designation of eligible telecommunications carriers.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 47 Telecommunication 3 2012-10-01 2012-10-01 false Additional requirements for Commission designation of eligible telecommunications carriers. 54.202 Section 54.202 Telecommunication FEDERAL... telecommunications carriers. (a) In order to be designated an eligible telecommunications carrier under section 214(e...

47 CFR 54.202 - Additional requirements for Commission designation of eligible telecommunications carriers.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 3 2013-10-01 2013-10-01 false Additional requirements for Commission designation of eligible telecommunications carriers. 54.202 Section 54.202 Telecommunication FEDERAL... telecommunications carriers. (a) In order to be designated an eligible telecommunications carrier under section 214(e...

New ideas for shallow gas well control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bourgoyne, A.T.; Kelly, O.A.; Sandoz, C.L.

1996-06-01

Flow from an unexpected shallow gas sand is one of the most difficult well control problems faced by oil and gas well operators during drilling operations. Current well control practice for bottom-supported marine rigs usually calls for shutting in the well when a kick is detected, if sufficient casing has been set to keep any flow underground. However, when shallow gas is encountered, casing may not be set deep enough to keep the underground flow from broaching to surface near the platform foundations. Once the flow reaches surface, craters are sometimes formed which can lead to loss of the rigmore » and associated marine structures. This short article overviews an ongoing study by Louisiana State University of the breakdown resistance of shallow marine sediments, using leak-off test data and geotechnical reports provided by Unocal. Such study is important for improving the characterization of shallow marine sediments to allow more reliable shallow casing designs, as the authors will conclude. This study has already proven that sediment failure mechanisms that lead to cratering have been poorly understood. In addition, there has been considerable uncertainty as to the best choices of well design parameters and well control contingency plans that will minimize risks associated with a shallow gas flow.« less

49 CFR 173.466 - Additional tests for Type A packagings designed for liquids and gases.

Code of Federal Regulations, 2010 CFR

2010-10-01

... for liquids and gases. 173.466 Section 173.466 Transportation Other Regulations Relating to...) Materials § 173.466 Additional tests for Type A packagings designed for liquids and gases. (a) In addition to the tests prescribed in § 173.465, Type A packagings designed for liquids and gases must be...

49 CFR 173.466 - Additional tests for Type A packagings designed for liquids and gases.

Code of Federal Regulations, 2011 CFR

2011-10-01

... for liquids and gases. 173.466 Section 173.466 Transportation Other Regulations Relating to...) Materials § 173.466 Additional tests for Type A packagings designed for liquids and gases. (a) In addition to the tests prescribed in § 173.465, Type A packagings designed for liquids and gases must be...

49 CFR 173.466 - Additional tests for Type A packagings designed for liquids and gases.

Code of Federal Regulations, 2012 CFR

2012-10-01

... for liquids and gases. 173.466 Section 173.466 Transportation Other Regulations Relating to...) Materials § 173.466 Additional tests for Type A packagings designed for liquids and gases. (a) In addition to the tests prescribed in § 173.465, Type A packagings designed for liquids and gases must be...

49 CFR 173.466 - Additional tests for Type A packagings designed for liquids and gases.

Code of Federal Regulations, 2013 CFR

2013-10-01

... for liquids and gases. 173.466 Section 173.466 Transportation Other Regulations Relating to...) Materials § 173.466 Additional tests for Type A packagings designed for liquids and gases. (a) In addition to the tests prescribed in § 173.465, Type A packagings designed for liquids and gases must be...

49 CFR 173.466 - Additional tests for Type A packagings designed for liquids and gases.

Code of Federal Regulations, 2014 CFR

2014-10-01

... for liquids and gases. 173.466 Section 173.466 Transportation Other Regulations Relating to...) Materials § 173.466 Additional tests for Type A packagings designed for liquids and gases. (a) In addition to the tests prescribed in § 173.465, Type A packagings designed for liquids and gases must be...

When friendship formation goes down the toilet: design features of shared accommodation influence interpersonal bonds and well-being.

PubMed

Easterbrook, Matthew J; Vignoles, Vivian L

2015-03-01

Despite its omnipresence, the influence of the built environment on human psychology is not well understood. In a five-wave longitudinal study, we investigated whether physical design features within shared student accommodation predicted the frequency of coincidental meetings between new flatmates, and whether these meetings predicted the strength of their interpersonal bonds and psychological well-being. Multilevel latent growth modelling on responses from 462 new university residents supported our hypotheses: Respondents living in flats with design features that encouraged the use of communal areas--a shared common area and an absence of ensuite toilets--reported unintentionally meeting their flatmates more frequently within their flats. This in turn predicted the initial strength of their interpersonal bonds with their flatmates, which in turn positively predicted their well-being. These effects were maintained throughout the 10-week study. Our findings provide an empirical basis for the development of shared housing designed to foster positive relationships and well-being among residents. © 2014 The British Psychological Society.

Design of the South East Asian Nutrition Survey (SEANUTS): a four-country multistage cluster design study.

PubMed

Schaafsma, Anne; Deurenberg, Paul; Calame, Wim; van den Heuvel, Ellen G H M; van Beusekom, Christien; Hautvast, Jo; Sandjaja; Bee Koon, Poh; Rojroongwasinkul, Nipa; Le Nguyen, Bao Khanh; Parikh, Panam; Khouw, Ilse

2013-09-01

Nutrition is a well-known factor in the growth, health and development of children. It is also acknowledged that worldwide many people have dietary imbalances resulting in over- or undernutrition. In 2009, the multinational food company FrieslandCampina initiated the South East Asian Nutrition Survey (SEANUTS), a combination of surveys carried out in Indonesia, Malaysia, Thailand and Vietnam, to get a better insight into these imbalances. The present study describes the general study design and methodology, as well as some problems and pitfalls encountered. In each of these countries, participants in the age range of 0·5-12 years were recruited according to a multistage cluster randomised or stratified random sampling methodology. Field teams took care of recruitment and data collection. For the health status of children, growth and body composition, physical activity, bone density, and development and cognition were measured. For nutrition, food intake and food habits were assessed by questionnaires, whereas in subpopulations blood and urine samples were collected to measure the biochemical status parameters of Fe, vitamins A and D, and DHA. In Thailand, the researchers additionally studied the lipid profile in blood, whereas in Indonesia iodine excretion in urine was analysed. Biochemical data were analysed in certified laboratories. Study protocols and methodology were aligned where practically possible. In December 2011, data collection was finalised. In total, 16,744 children participated in the present study. Information that will be very relevant for formulating nutritional health policies, as well as for designing innovative food and nutrition research and development programmes, has become available.

Experimental design and statistical analysis for three-drug combination studies.

PubMed

Fang, Hong-Bin; Chen, Xuerong; Pei, Xin-Yan; Grant, Steven; Tan, Ming

2017-06-01

Drug combination is a critically important therapeutic approach for complex diseases such as cancer and HIV due to its potential for efficacy at lower, less toxic doses and the need to move new therapies rapidly into clinical trials. One of the key issues is to identify which combinations are additive, synergistic, or antagonistic. While the value of multidrug combinations has been well recognized in the cancer research community, to our best knowledge, all existing experimental studies rely on fixing the dose of one drug to reduce the dimensionality, e.g. looking at pairwise two-drug combinations, a suboptimal design. Hence, there is an urgent need to develop experimental design and analysis methods for studying multidrug combinations directly. Because the complexity of the problem increases exponentially with the number of constituent drugs, there has been little progress in the development of methods for the design and analysis of high-dimensional drug combinations. In fact, contrary to common mathematical reasoning, the case of three-drug combinations is fundamentally more difficult than two-drug combinations. Apparently, finding doses of the combination, number of combinations, and replicates needed to detect departures from additivity depends on dose-response shapes of individual constituent drugs. Thus, different classes of drugs of different dose-response shapes need to be treated as a separate case. Our application and case studies develop dose finding and sample size method for detecting departures from additivity with several common (linear and log-linear) classes of single dose-response curves. Furthermore, utilizing the geometric features of the interaction index, we propose a nonparametric model to estimate the interaction index surface by B-spine approximation and derive its asymptotic properties. Utilizing the method, we designed and analyzed a combination study of three anticancer drugs, PD184, HA14-1, and CEP3891 inhibiting myeloma H929 cell line

Study on thermal effects & sulfurized additives, in lubricating greases

NASA Astrophysics Data System (ADS)

Shah, Ami Atul

Lithium Base grease constitutes about 50% of market. The greases are developed to be able to work in multiple working conditions and have longer working life. Greases with extreme pressure additives and anti-wear additives have been developed as a solution to many of the applications. These developed greases are tested under ASTM D2266 testing conditions to meet the requirements. The actual working conditions, although, differ than the real testing conditions. The loading, speed and temperature conditions can be more harsh, or fluctuating in nature. The cyclic nature of the parameters cannot be directly related to the test performance. For this purpose studies on the performance under spectrum loading, variable speed and fluctuating temperature must be performed. This study includes tests to understand the effect of thermal variation on some of the most commonly used grease additives that perform well under ASTM D2266 testing conditions. The studied additives include most widely used industrial extreme pressure additive MoS2. Performance of ZDDP which is trying to replace MoS2 in its industrial applications has also been studied. The tests cover study of extreme pressure, anti-wear and friction modifier additives to get a general idea on the effects of thermal variation in three areas. Sulphur is the most common extreme pressure additive. Sulphur based MoS 2 is extensively used grease additive. Study to understand the tribological performance of this additive through wear testing and SEM/EDX studies has been done. This performance is also studied for other metallic sulfides like WS2 and sulphur based organic compound. The aim is to study the importance of the type of bond that sulphur shares in its additive's structure on its performance. The MoS2 film formation is found to be on the basis of the FeS formation on the substrate and protection through sacrificial monolayer deposition of the MoS2 sheared structure. The free Mo then tends to oxidise. An attempt to

Additive Manufacturing in Production: A Study Case Applying Technical Requirements

NASA Astrophysics Data System (ADS)

Ituarte, Iñigo Flores; Coatanea, Eric; Salmi, Mika; Tuomi, Jukka; Partanen, Jouni

Additive manufacturing (AM) is expanding the manufacturing capabilities. However, quality of AM produced parts is dependent on a number of machine, geometry and process parameters. The variability of these parameters affects the manufacturing drastically and therefore standardized processes and harmonized methodologies need to be developed to characterize the technology for end use applications and enable the technology for manufacturing. This research proposes a composite methodology integrating Taguchi Design of Experiments, multi-objective optimization and statistical process control, to optimize the manufacturing process and fulfil multiple requirements imposed to an arbitrary geometry. The proposed methodology aims to characterize AM technology depending upon manufacturing process variables as well as to perform a comparative assessment of three AM technologies (Selective Laser Sintering, Laser Stereolithography and Polyjet). Results indicate that only one machine, laser-based Stereolithography, was feasible to fulfil simultaneously macro and micro level geometrical requirements but mechanical properties were not at required level. Future research will study a single AM system at the time to characterize AM machine technical capabilities and stimulate pre-normative initiatives of the technology for end use applications.

Design and modeling of an additive manufactured thin shell for x-ray astronomy

NASA Astrophysics Data System (ADS)

Feldman, Charlotte; Atkins, Carolyn; Brooks, David; Watson, Stephen; Cochrane, William; Roulet, Melanie; Willingale, Richard; Doel, Peter

2017-09-01

Future X-ray astronomy missions require light-weight thin shells to provide large collecting areas within the weight limits of launch vehicles, whilst still delivering angular resolutions close to that of Chandra (0.5 arc seconds). Additive manufacturing (AM), also known as 3D printing, is a well-established technology with the ability to construct or `print' intricate support structures, which can be both integral and light-weight, and is therefore a candidate technique for producing shells for space-based X-ray telescopes. The work described here is a feasibility study into this technology for precision X-ray optics for astronomy and has been sponsored by the UK Space Agency's National Space Technology Programme. The goal of the project is to use a series of test samples to trial different materials and processes with the aim of developing a viable path for the production of an X-ray reflecting prototype for astronomical applications. The initial design of an AM prototype X-ray shell is presented with ray-trace modelling and analysis of the X-ray performance. The polishing process may cause print-through from the light-weight support structure on to the reflecting surface. Investigations in to the effect of the print-through on the X-ray performance of the shell are also presented.

Optimal design in pediatric pharmacokinetic and pharmacodynamic clinical studies.

PubMed

Roberts, Jessica K; Stockmann, Chris; Balch, Alfred; Yu, Tian; Ward, Robert M; Spigarelli, Michael G; Sherwin, Catherine M T

2015-03-01

It is not trivial to conduct clinical trials with pediatric participants. Ethical, logistical, and financial considerations add to the complexity of pediatric studies. Optimal design theory allows investigators the opportunity to apply mathematical optimization algorithms to define how to structure their data collection to answer focused research questions. These techniques can be used to determine an optimal sample size, optimal sample times, and the number of samples required for pharmacokinetic and pharmacodynamic studies. The aim of this review is to demonstrate how to determine optimal sample size, optimal sample times, and the number of samples required from each patient by presenting specific examples using optimal design tools. Additionally, this review aims to discuss the relative usefulness of sparse vs rich data. This review is intended to educate the clinician, as well as the basic research scientist, whom plan on conducting a pharmacokinetic/pharmacodynamic clinical trial in pediatric patients. © 2015 John Wiley & Sons Ltd.

Shuttle/tethered satellite system conceptual design study

NASA Technical Reports Server (NTRS)

1976-01-01

A closed-loop control system was added to the tether reel which improves control over the tethered satellite. In addition to increasing the stability of the tethered satellite along local vertical, this control system is used for deployment and retrieval of tethered satellites. This conceptual design study describes a tether system for suspending a science payload at an altitude of 120 km from space shuttle orbiter flying at an altitude of 200 km. In addition to the hardware conceptual designs, various aspects concerning Orbiter accommodations are discussed.

Theoretical and experimental investigation of design for multioptical-axis freeform progressive addition lenses

NASA Astrophysics Data System (ADS)

Xiang, HuaZhong; Chen, JiaBi; Zhu, TianFen; Wei, YeFei; Fu, DongXiang

2015-11-01

A freeform progressive addition lens (PAL) provides a good solution to correct presbyopia and prevent juvenile myopia by distributing pupils' optical powers of distance zone, near zone, and intermediate zone and is more widely adopted in the present optometric study. However, there is still a lack of a single-optical-axis system for the design of a PAL. This paper focuses on the research for an approach for designing a freeform PAL. A multioptical-axis system based on real viewing conditions using the eyes is employed for the representation of the freeform surface. We filled small pupils in the intermediate zone as a progressive corridor and the distance- and near-vision portions were defined as the standard spherical surfaces delimited by quadratic curves. Three freeform PALs with a spherical surface as the front side and a freeform surface as the backside were designed. We demonstrate the fabrication and measurement technologies for the PAL surface using computer numerical control machine tools from Schneider Smart and a Visionix VM-2000 Lens Power Mapper. Surface power and astigmatic values were obtained. Preliminary results showed that the approach for the design and fabrication is helpful to advance the design procedure optimization and mass production of PALs in optometry.

Additive manufacturing of tunable lenses

NASA Astrophysics Data System (ADS)

Schlichting, Katja; Novak, Tobias; Heinrich, Andreas

2017-02-01

Individual additive manufacturing of optical systems based on 3D Printing offers varied possibilities in design and usage. In addition to the additive manufacturing procedure, the usage of tunable lenses allows further advantages for intelligent optical systems. Our goal is to bring the advantages of additive manufacturing together with the huge potential of tunable lenses. We produced tunable lenses as a bundle without any further processing steps, like polishing. The lenses were designed and directly printed with a 3D Printer as a package. The design contains the membrane as an optical part as well as the mechanical parts of the lens, like the attachments for the sleeves which contain the oil. The dynamic optical lenses were filled with an oil. The focal length of the lenses changes due to a change of the radius of curvature. This change is caused by changing the pressure in the inside of the lens. In addition to that, we designed lenses with special structures to obtain different areas with an individual optical power. We want to discuss the huge potential of this technology for several applications. Further, an appropriate controlling system is needed. Wéll show the possibilities to control and regulate the optical power of the lenses. The lenses could be used for illumination tasks, and in the future, for individual measurement tasks. The main advantage is the individuality and the possibility to create an individual design which completely fulfills the requirements for any specific application.

Additive-manufactured patient-specific titanium templates for thoracic pedicle screw placement: novel design with reduced contact area.

PubMed

Takemoto, Mitsuru; Fujibayashi, Shunsuke; Ota, Eigo; Otsuki, Bungo; Kimura, Hiroaki; Sakamoto, Takeshi; Kawai, Toshiyuki; Futami, Tohru; Sasaki, Kiyoyuki; Matsushita, Tomiharu; Nakamura, Takashi; Neo, Masashi; Matsuda, Shuich

2016-06-01

Image-based navigational patient-specific templates (PSTs) for pedicle screw (PS) placement have been described. With recent advances in three-dimensional computer-aided designs and additive manufacturing technology, various PST designs have been reported, although the template designs were not optimized. We have developed a novel PST design that reduces the contact area without sacrificing stability. It avoids susceptibility to intervening soft tissue, template geometric inaccuracy, and difficulty during template fitting. Fourteen candidate locations on the posterior aspect of the vertebra were evaluated. Among them, locations that had high reproducibility on computed tomography (CT) images and facilitated accurate PS placement were selected for the final PST design. An additive manufacturing machine (EOSINT M270) fabricated the PSTs using commercially pure titanium powder. For the clinical study, 36 scoliosis patients and 4 patients with ossification of the posterior longitudinal ligament (OPLL) were treated with thoracic PSs using our newly developed PSTs. We intraoperatively and postoperatively evaluated the accuracy of the PS hole created by the PST. Based on the segmentation reproducibility and stability analyses, we selected seven small, round contact points for our PST: bilateral superior and inferior points on the transverse process base, bilateral inferior points on the laminar, and a superior point on the spinous process. Clinically, the success rates of PS placement using this PST design were 98.6 % (414/420) for scoliosis patients and 100 % (46/46) for OPLL patients. This study provides a useful design concept for the development and introduction of patient-specific navigational templates for placing PSs.

Design and calibration of zero-additional-phase SPIDER

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baum, Peter; Riedle, Eberhard

2005-09-01

Zero-additional-phase spectral phase interferometry for direct electric field reconstruction (ZAP-SPIDER) is a novel technique for measuring the temporal shape and phase of ultrashort optical pulses directly at the interaction point of a spectroscopic experiment. The scheme is suitable for an extremely wide wavelength region from the ultraviolet to the near infrared. We present a comprehensive description of the experimental setup and design guidelines to effectively apply the technique to various wavelengths and pulse durations. The calibration of the setup and procedures to check the consistency of the measurement are discussed in detail. We show experimental data for various center wavelengthsmore » and pulse durations down to 7 fs to verify the applicability to a wide range of pulse parameters.« less

Building the evidence base for REDD+: Study design and methods for evaluating the impacts of conservation interventions on local well-being

PubMed Central

Sills, Erin O.; de Sassi, Claudio; Jagger, Pamela; Lawlor, Kathleen; Miteva, Daniela A.; Pattanayak, Subhrendu K.; Sunderlin, William D.

2018-01-01

Climate change mitigation in developing countries is increasingly expected to generate co-benefits that help meet sustainable development goals. This has been an expectation and a hotly contested issue in REDD+ (reducing emissions from deforestation and forest degradation) since its inception. While the core purpose of REDD+ is to reduce carbon emissions, its legitimacy and success also depend on its impacts on local well-being. To effectively safeguard against negative impacts, we need to know whether and which well-being outcomes can be attributed to REDD+. Yet, distinguishing the effects of choosing particular areas for REDD+ from the effects of the interventions themselves remains a challenge. The Global Comparative Study (GCS) on REDD+ employed a quasi-experimental before-after-control-intervention (BACI) study design to address this challenge and evaluate the impacts of 16 REDD+ pilots across the tropics. We find that the GCS approach allows identification of control groups that represent the counterfactual, thereby permitting attribution of outcomes to REDD+. The GCS experience belies many of the common critiques of the BACI design, especially concerns about collecting baseline data on control groups. Our findings encourage and validate the early planning and up-front investments required to evaluate the local impacts of global climate change mitigation efforts with confidence. The stakes are high, both for the global environment and for local populations directly affected by those efforts. The standards for evidence should be concomitantly high. PMID:29681690

Building the evidence base for REDD+: Study design and methods for evaluating the impacts of conservation interventions on local well-being.

PubMed

Sills, Erin O; de Sassi, Claudio; Jagger, Pamela; Lawlor, Kathleen; Miteva, Daniela A; Pattanayak, Subhrendu K; Sunderlin, William D

2017-03-01

Climate change mitigation in developing countries is increasingly expected to generate co-benefits that help meet sustainable development goals. This has been an expectation and a hotly contested issue in REDD+ (reducing emissions from deforestation and forest degradation) since its inception. While the core purpose of REDD+ is to reduce carbon emissions, its legitimacy and success also depend on its impacts on local well-being. To effectively safeguard against negative impacts, we need to know whether and which well-being outcomes can be attributed to REDD+. Yet, distinguishing the effects of choosing particular areas for REDD+ from the effects of the interventions themselves remains a challenge. The Global Comparative Study (GCS) on REDD+ employed a quasi-experimental before-after-control-intervention (BACI) study design to address this challenge and evaluate the impacts of 16 REDD+ pilots across the tropics. We find that the GCS approach allows identification of control groups that represent the counterfactual, thereby permitting attribution of outcomes to REDD+. The GCS experience belies many of the common critiques of the BACI design, especially concerns about collecting baseline data on control groups. Our findings encourage and validate the early planning and up-front investments required to evaluate the local impacts of global climate change mitigation efforts with confidence. The stakes are high, both for the global environment and for local populations directly affected by those efforts. The standards for evidence should be concomitantly high.

30 CFR 250.413 - What must my description of well drilling design criteria address?

Code of Federal Regulations, 2010 CFR

2010-07-01

... design criteria address? 250.413 Section 250.413 Mineral Resources MINERALS MANAGEMENT SERVICE... drilling design criteria address? Your description of well drilling design criteria must address: (a) Pore... phases, including the anticipated surface pressure used for designing the production string; (g) A single...

Additional road markings as an indication of speed limits: results of a field experiment and a driving simulator study.

PubMed

Daniels, Stijn; Vanrie, Jan; Dreesen, An; Brijs, Tom

2010-05-01

Although speed limits are indicated by road signs, road users are not always aware, while driving, of the actual speed limit on a given road segment. The Roads and Traffic Agency developed additional road markings in order to support driver decisions on speed on 70 km/h roads in Flanders-Belgium. In this paper the results are presented of two evaluation studies, both a field study and a simulator study, on the effects of the additional road markings on speed behaviour. The results of the field study showed no substantial effect of the markings on speed behaviour. Neither did the simulator study, with slightly different stimuli. Nevertheless an effect on lateral position was noticed in the simulator study, showing at least some effect of the markings. The role of conspicuity of design elements and expectations towards traffic environments is discussed. Both studies illustrate well some strengths and weaknesses of observational field studies compared to experimental simulator studies. Copyright (c) 2009 Elsevier Ltd. All rights reserved.

Design and development of a layer-based additive manufacturing process for the realization of metal parts of designed mesostructure

NASA Astrophysics Data System (ADS)

Williams, Christopher Bryant

Low-density cellular materials, metallic bodies with gaseous voids, are a unique class of materials that are characterized by their high strength, low mass, good energy absorption characteristics, and good thermal and acoustic insulation properties. In an effort to take advantage of this entire suite of positive mechanical traits, designers are tailoring the cellular mesostructure for multiple design objectives. Unfortunately, existing cellular material manufacturing technologies limit the design space as they are limited to certain part mesostructure, material type, and macrostructure. The opportunity that exists to improve the design of existing products, and the ability to reap the benefits of cellular materials in new applications is the driving force behind this research. As such, the primary research goal of this work is to design, embody, and analyze a manufacturing process that provides a designer the ability to specify the material type, material composition, void morphology, and mesostructure topology for any conceivable part geometry. The accomplishment of this goal is achieved in three phases of research: (1) Design---Following a systematic design process and a rigorous selection exercise, a layer-based additive manufacturing process is designed that is capable of meeting the unique requirements of fabricating cellular material geometry. Specifically, metal parts of designed mesostructure are fabricated via three-dimensional printing of metal oxide ceramic powder followed by post-processing in a reducing atmosphere. (2) Embodiment ---The primary research hypothesis is verified through the use of the designed manufacturing process chain to successfully realize metal parts of designed mesostructure. (3) Modeling & Evaluation ---The designed manufacturing process is modeled in this final research phase so as to increase understanding of experimental results and to establish a foundation for future analytical modeling research. In addition to an analysis of

77 FR 2545 - Designation of a Class of Employees for Addition to the Special Exposure Cohort

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-18

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Designation of a Class of Employees for Addition to the... of Health and Human Services (HHS). ACTION: Notice. SUMMARY: HHS gives notice of a decision to designate a class of employees from the Pantex Plant in Amarillo, Texas, as an addition to the Special...

Design for Health and Well Being: Knitted Products for Diabetics

NASA Astrophysics Data System (ADS)

Gault, A.

2016-07-01

This paper will discuss the design development, manufacturing and testing of knitted products maximizing the use of new innovations in Nano- technology and the integration of Phase Changing Materials specifically for diabetics. The project identified key aspects requiring design solutions to bring improvement to the circulatory problems with specific reference to the diabetic condition. Diabetics have particular difficulty in regulating their body temperature and this can result in the condition worsening, and resulting in loss of digits or limbs. The design of products to prevent the deterioration of the diabetic condition and to help those with limb loss was developed in collaboration with a Northern Ireland diabetic consultant, a product engineer and a knitwear designer. The fusion of ideas between the stakeholders resulted in the development and manufacture of a range of products that have been successfully tested at the yarn and fabric development stage and have been proven to maintain body temperature by either cooling or warming and therefore bring improvement to health and well-being. Whilst the product has a performance element the design ideas created desirable products that not only provided solutions to the brief but also resulted in products that had further market applications.

Recommendations for research design of telehealth studies.

PubMed

Chumbler, Neale R; Kobb, Rita; Brennan, David M; Rabinowitz, Terry

2008-11-01

Properly designed randomized controlled trials (RCTs) are the gold standard to use when examining the effectiveness of telehealth interventions on clinical outcomes. Some published telehealth studies have employed well-designed RCTs. However, such methods are not always feasible and practical in particular settings. This white paper addresses not only the need for properly designed RCTs, but also offers alternative research designs, such as quasi-experimental designs, and statistical techniques that can be employed to rigorously assess the effectiveness of telehealth studies. This paper further offers design and measurement recommendations aimed at and relevant to administrative decision-makers, policymakers, and practicing clinicians.

Value engineering on the designed operator work tools for brick and rings wells production

NASA Astrophysics Data System (ADS)

Ayu Bidiawati J., R.; Muchtiar, Yesmizarti; Wariza, Ragil Okta

2017-06-01

Operator working tools in making brick and ring wells were designed and made, and the value engineering was calculated to identify and develop the function of these tools in obtaining the balance between cost, reliability and appearance. This study focused on the value of functional components of the tools and attempted to increase the difference between the costs incurred by the generated values. The purpose of this study was to determine the alternatives of tools design and to determine the performance of each alternative. The technique was developed using FAST method that consisted of five stages: information, creative, analytical, development and presentation stage. The results of the analysis concluded that the designed tools have higher value and better function description. There were four alternative draft improvements for operator working tools. The best alternative was determined based on the rank by using matrix evaluation. Best performance was obtained by the alternative II, amounting to 98.92 with a value of 0.77.

Democratizing science with the aid of parametric design and additive manufacturing: Design and fabrication of a versatile and low-cost optical instrument for scattering measurement.

PubMed

Nadal-Serrano, Jose M; Nadal-Serrano, Adolfo; Lopez-Vallejo, Marisa

2017-01-01

This paper focuses on the application of rapid prototyping techniques using additive manufacturing in combination with parametric design to create low-cost, yet accurate and reliable instruments. The methodology followed makes it possible to make instruments with a degree of customization until now available only to a narrow audience, helping democratize science. The proposal discusses a holistic design-for-manufacturing approach that comprises advanced modeling techniques, open-source design strategies, and an optimization algorithm using free parametric software for both professional and educational purposes. The design and fabrication of an instrument for scattering measurement is used as a case of study to present the previous concepts.

Democratizing science with the aid of parametric design and additive manufacturing: Design and fabrication of a versatile and low-cost optical instrument for scattering measurement

PubMed Central

Lopez-Vallejo, Marisa

2017-01-01

This paper focuses on the application of rapid prototyping techniques using additive manufacturing in combination with parametric design to create low-cost, yet accurate and reliable instruments. The methodology followed makes it possible to make instruments with a degree of customization until now available only to a narrow audience, helping democratize science. The proposal discusses a holistic design-for-manufacturing approach that comprises advanced modeling techniques, open-source design strategies, and an optimization algorithm using free parametric software for both professional and educational purposes. The design and fabrication of an instrument for scattering measurement is used as a case of study to present the previous concepts. PMID:29112987

A Time of Flight Fast Neutron Imaging System Design Study

NASA Astrophysics Data System (ADS)

Canion, Bonnie; Glenn, Andrew; Sheets, Steven; Wurtz, Ron; Nakae, Les; Hausladen, Paul; McConchie, Seth; Blackston, Matthew; Fabris, Lorenzo; Newby, Jason

2017-09-01

LLNL and ORNL are designing an active/passive fast neutron imaging system that is flexible to non-ideal detector positioning. It is often not possible to move an inspection object in fieldable imager applications such as safeguards, arms control treaty verification, and emergency response. Particularly, we are interested in scenarios which inspectors do not have access to all sides of an inspection object, due to interfering objects or walls. This paper will present the results of a simulation-based design parameter study, that will determine the optimum system design parameters for a fieldable system to perform time-of-flight based imaging analysis. The imaging analysis is based on the use of an associated particle imaging deuterium-tritium (API DT) neutron generator to get the time-of-flight of radiation induced within an inspection object. This design study will investigate the optimum design parameters for such a system (e.g. detector size, ideal placement, etc.), as well as the upper and lower feasible design parameters that the system can expect to provide results within a reasonable amount of time (e.g. minimum/maximum detector efficiency, detector standoff, etc.). Ideally the final prototype from this project will be capable of using full-access techniques, such as transmission imaging, when the measurement circumstances allow, but with the additional capability of producing results at reduced accessibility.

Design, Development and Hotfire Testing of Monolithic Copper and Bimetallic Additively Manufactured Combustion Chambers

NASA Technical Reports Server (NTRS)

Gradl, Paul; Barnett, Greg; Brandsmeier, Will; Greene, Sandy Elam; Protz, Chris

2016-01-01

NASA and industry partners are working towards fabrication process development to reduce costs and schedules associated with manufacturing liquid rocket engine components with the goal of reducing overall mission costs. One such technique being evaluated is powder-bed fusion or selective laser melting (SLM) otherwise commonly referred to as additive manufacturing. The NASA Low Cost Upper Stage Propulsion (LCUSP) program was designed to develop processes and material characterization for the GRCop-84 copper-alloy commensurate with powder bed additive manufacturing, evaluate bimetallic deposition and complete testing of a full scale combustion chamber. As part of this development, the process has been transferred to industry partners to enable a long-term supply chain of monolithic copper combustion chambers. As a direct spin off of this program, NASA is working with industry partners to further develop the printing process for the GRCop-84 material in addition to the C-18150 (CuCrZr) material. To advance the process further and allow for optimization with multiple materials, NASA is also investigating the feasibility of bimetallic additively manufactured chambers. A 1.2k sized thrust-chamber was designed and developed to compare the printing process of the GRCop-84 and C-18150 SLM materials. A series of similar MCC liners also completed development with an Inconel 625 jacket bonded to the GRcop-84 liner evaluating direct metal deposition (DMD) laser and arc-based techniques. This paper describes the design, development, manufacturing and testing of these combustion chambers and associated lessons learned throughout the design and development process.

Anatomically ordered tapping interferes more with one-digit addition than two-digit addition: a dual-task fMRI study.

PubMed

Soylu, Firat; Newman, Sharlene D

2016-02-01

Fingers are used as canonical representations for numbers across cultures. In previous imaging studies, it was shown that arithmetic processing activates neural resources that are known to participate in finger movements. Additionally, in one dual-task study, it was shown that anatomically ordered finger tapping disrupts addition and subtraction more than multiplication, possibly due to a long-lasting effect of early finger counting experiences on the neural correlates and organization of addition and subtraction processes. How arithmetic task difficulty and tapping complexity affect the concurrent performance is still unclear. If early finger counting experiences have bearing on the neural correlates of arithmetic in adults, then one would expect anatomically and non-anatomically ordered tapping to have different interference effects, given that finger counting is usually anatomically ordered. To unravel these issues, we studied how (1) arithmetic task difficulty and (2) the complexity of the finger tapping sequence (anatomical vs. non-anatomical ordering) affect concurrent performance and use of key neural circuits using a mixed block/event-related dual-task fMRI design with adult participants. The results suggest that complexity of the tapping sequence modulates interference on addition, and that one-digit addition (fact retrieval), compared to two-digit addition (calculation), is more affected from anatomically ordered tapping. The region-of-interest analysis showed higher left angular gyrus BOLD response for one-digit compared to two-digit addition, and in no-tapping conditions than dual tapping conditions. The results support a specific association between addition fact retrieval and anatomically ordered finger movements in adults, possibly due to finger counting strategies that deploy anatomically ordered finger movements early in the development.

Case study of landfill leachate recirculation using small-diameter vertical wells.

PubMed

Jain, Pradeep; Ko, Jae Hac; Kumar, Dinesh; Powell, Jon; Kim, Hwidong; Maldonado, Lizmarie; Townsend, Timothy; Reinhart, Debra R

2014-11-01

A case study of landfill liquids addition using small diameter (5 cm) vertical wells is reported. More than 25,000 m(3) of leachate was added via 134 vertical wells installed 3 m, 12 m, and 18 m deep over five years in a landfill in Florida, US. Liquids addition performance (flow rate per unit screen length per unit liquid head) ranged from 5.6×10(-8) to 3.6×10(-6) m(3) s(-1) per m screen length per m liquid head. The estimated radial hydraulic conductivity ranged from 3.5×10(-6) to 4.2×10(-4) m s(-1). The extent of lateral moisture movement ranged from 8 to 10 m based on the responses of moisture sensors installed around vertical well clusters, and surface seeps were found to limit the achievable liquids addition rates, despite the use of concrete collars under a pressurized liquids addition scenario. The average moisture content before (51 samples) and after (272 samples) the recirculation experiments were 23% (wet weight basis) and 45% (wet weight basis), respectively, and biochemical methane potential measurements of excavated waste indicated significant (p<0.025) decomposition. Copyright © 2014 Elsevier Ltd. All rights reserved.

A FIELD STUDY TO COMPARE PERFORMANCE OF STAINLESS STEEL RESEARCH MONITORING WELLS WITH EXISTING ON-FARM DRINKING WATER WELLS IN MEASURING PESTICIDE AND NITRATE CONCENTRATIONS

EPA Science Inventory

Existing drinking wells are widely used for the collection of ground water samples to evaluate chemical contamination. A well comparison study was conducted to compare pesticide and nitrate-N data from specially designed stainless steel research monitoring wells with data from ne...

78 FR 68461 - Guidance for Industry: Studies To Evaluate the Utility of Anti-Salmonella Chemical Food Additives...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-14

...] Guidance for Industry: Studies To Evaluate the Utility of Anti- Salmonella Chemical Food Additives in Feeds... Industry: Studies to Evaluate the Utility of Anti-Salmonella Chemical Food Additives in Feeds,'' and is... of Anti-Salmonella Chemical Food Additives in Feeds (GFI 80) is to help sponsors design efficacy...

A study of hydrocarbons associated with brines from DOE geopressured wells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Keeley, D.F.

1993-01-01

Accomplishments are summarized on the following tasks: distribution coefficients and solubilities, DOE design well sampling, analysis of well samples, review of theoretical models of geopressured reservoir hydrocarbons, monitor for aliphatic hydrocarbons, development of a ph meter probe, DOE design well scrubber analysis, removal and disposition of gas scrubber equipment at Pleasant Bayou Well, and disposition of archived brines.

Study of design constraints on helicopter noise

NASA Technical Reports Server (NTRS)

Sternfeld, H., Jr.; Wiedersum, C. W.

1979-01-01

A means of estimating the noise generated by a helicopter main rotor using information which is generally available during the preliminary design phase of aircraft development is presented. The method utilizes design charts and tables which do not require an understanding of acoustical theory or computational procedures in order to predict the perceived noise level, a weighted sound pressure level, or C weighted sound pressure level of a single hovering rotor. A method for estimating the effective perceived noise level in forward flight is also included. In order to give the designer an assessment of the relative rotor performance, which may be traded off against noise, an additional chart for estimating the percent of available rotor thrust which must be expended in lifting the rotor and drive system, is included as well as approach for comparing the subjective acceptability of various rotors once the absolute sound pressure levels are predicted.

Study design and "evidence" in patient-oriented research.

PubMed

Concato, John

2013-06-01

Individual studies in patient-oriented research, whether described as "comparative effectiveness" or using other terms, are based on underlying methodological designs. A simple taxonomy of study designs includes randomized controlled trials on the one hand, and observational studies (such as case series, cohort studies, and case-control studies) on the other. A rigid hierarchy of these design types is a fairly recent phenomenon, promoted as a tenet of "evidence-based medicine," with randomized controlled trials receiving gold-standard status in terms of producing valid results. Although randomized trials have many strengths, and contribute substantially to the evidence base in clinical care, making presumptions about the quality of a study based solely on category of research design is unscientific. Both the limitations of randomized trials as well as the strengths of observational studies tend to be overlooked when a priori assumptions are made. This essay presents an argument in support of a more balanced approach to evaluating evidence, and discusses representative examples from the general medical as well as pulmonary and critical care literature. The simultaneous consideration of validity (whether results are correct "internally") and generalizability (how well results apply to "external" populations) is warranted in assessing whether a study's results are accurate for patients likely to receive the intervention-examining the intersection of clinical and methodological issues in what can be called a medicine-based evidence approach. Examination of cause-effect associations in patient-oriented research should recognize both the strengths and limitations of randomized trials as well as observational studies.

Embracing additive manufacture: implications for foot and ankle orthosis design

PubMed Central

2012-01-01

Background The design of foot and ankle orthoses is currently limited by the methods used to fabricate the devices, particularly in terms of geometric freedom and potential to include innovative new features. Additive manufacturing (AM) technologies, where objects are constructed via a series of sub-millimetre layers of a substrate material, may present the opportunity to overcome these limitations and allow novel devices to be produced that are highly personalised for the individual, both in terms of fit and functionality. Two novel devices, a foot orthosis (FO) designed to include adjustable elements to relieve pressure at the metatarsal heads, and an ankle foot orthosis (AFO) designed to have adjustable stiffness levels in the sagittal plane, were developed and fabricated using AM. The devices were then tested on a healthy participant to determine if the intended biomechanical modes of action were achieved. Results The adjustable, pressure relieving FO was found to be able to significantly reduce pressure under the targeted metatarsal heads. The AFO was shown to have distinct effects on ankle kinematics which could be varied by adjusting the stiffness level of the device. Conclusions The results presented here demonstrate the potential design freedom made available by AM, and suggest that it may allow novel personalised orthotic devices to be produced which are beyond the current state of the art. PMID:22642941

Holistic Design for Total Product Well Being

NASA Technical Reports Server (NTRS)

Adams, Chris W.; Hamilton, George S.

2004-01-01

Recent hardware development work at NASA's Marshall Space Flight Center creates and argument for the use of a holistic design approach as opposed to a piece part design approach. A piece part design approach being one where individual pieces are developed to their finished state having to meet certain interface and human engineering requirements without much consideration to the final product as a whole. A holistic design approach being one where the final product is evaluated early and frequently during the design process, and individual parts are developed with consideration to how they interact a whole,and how they interact with the user and environment. Examples from the development of the Materials Science Research Rack - 1 will illustrate: a design failure due to piece part design; a design save, due to a failure of piece part design, but saved by evaluating the design holistically; and a design success due to a holistic design approach.

Experimental procedure for measuring and comparing head-neck-trunk posture and movements caused by different progressive addition lens designs.

PubMed

Mateo, B; Porcar-Seder, R; Solaz, J S; Dürsteler, J C

2010-07-01

This study demonstrates that appropriate measurement procedures can detect differences in head movement in a near reading task when using three different progressive addition lenses (PALs). The movements were measured using an anatomical reference system with a biomechanical rationale. This reference system was capable of representing rotations for comparing head flexion relative to trunk, head flexion relative to neck, head rotation relative to trunk and trunk flexion. The subject sample comprised 31 volunteers and three PAL designs with different viewing zones were selected. Significant differences were found between the lenses for three of the seven movement parameters examined. The differences occurred for both vertical and horizontal head movements and could be attributed to aspects of the PAL design. The measurement of the complete kinematic trunk-neck-head chain improved the number of differences that were found over those in previous studies. STATEMENT OF RELEVANCE: The study proposes a methodology based on a biomechanical rationale able to differentiate head-neck-trunk posture and movements caused by different progressive addition lens designs with minimum invasiveness. This methodology could also be applied to analyse the ergonomics of other devices that restrict the user's field of view, such as helmets, personal protective equipment or helmet-mounted displays for pilots. This analysis will allow designers to optimise designs offering higher comfort and performance.

The Role of DNA Methylation in Cardiovascular Risk and Disease: Methodological Aspects, Study Design, and Data Analysis for Epidemiological Studies.

PubMed

Zhong, Jia; Agha, Golareh; Baccarelli, Andrea A

2016-01-08

Epidemiological studies have demonstrated that genetic, environmental, behavioral, and clinical factors contribute to cardiovascular disease development. How these risk factors interact at the cellular level to cause cardiovascular disease is not well known. Epigenetic epidemiology enables researchers to explore critical links between genomic coding, modifiable exposures, and manifestation of disease phenotype. One epigenetic link, DNA methylation, is potentially an important mechanism underlying these associations. In the past decade, there has been a significant increase in the number of epidemiological studies investigating cardiovascular risk factors and outcomes in relation to DNA methylation, but many gaps remain in our understanding of the underlying cause and biological implications. In this review, we provide a brief overview of the biology and mechanisms of DNA methylation and its role in cardiovascular disease. In addition, we summarize the current evidence base in epigenetic epidemiology studies relevant to cardiovascular health and disease and discuss the limitations, challenges, and future directions of the field. Finally, we provide guidelines for well-designed epigenetic epidemiology studies, with particular focus on methodological aspects, study design, and analytical challenges. © 2016 American Heart Association, Inc.

Do Wellness Tourists Get Well? An Observational Study of Multiple Dimensions of Health and Well-Being After a Week-Long Retreat

PubMed Central

Elliott, Fiona; Oates, Liza; Schembri, Adrian; Mantri, Nitin

2017-01-01

Abstract Background: Wellness retreats use many complementary and alternative therapies within a holistic residential setting, yet few studies have evaluated the effect of retreat experiences on multiple dimensions of health and well-being, and no published studies have reported health outcomes in wellness tourists. Objectives: To assess the effect of a week-long wellness-retreat experience in wellness tourists. Design: A longitudinal observational study with outcomes assessed upon arrival and departure and 6 weeks after the retreat. Setting: A rural health retreat in Queensland, Australia. Interventions: A holistic, 1-week, residential, retreat experience that included many educational, therapeutic, and leisure activities and an organic, mostly plant-based diet. Outcome measures: Multiple outcome measures were performed upon arrival and departure and 6 weeks after the retreat. These included anthropometric measures, urinary pesticide metabolites, a food and health symptom questionnaire, the Five Factor Wellness Inventory, the General Self Efficacy questionnaire, the Pittsburgh Insomnia Rating Scale, the Depression Anxiety Stress Scale, the Profile of Mood States, and the Cogstate cognitive function test battery. Results: Statistically significant improvements (p < 0.05) were seen in almost all measures (n = 37) after 1 week and were sustained at 6 weeks (n = 17). There were statistically significant improvements (p < 0.001) in all anthropometric measures after 1 week, with reductions in abdominal girth (2.7 cm), weight (1.6 kg), and average systolic and diastolic pressure (−16.1 mmHg and −9.3 mmHg, respectively). Statistically significant improvements (p < 0.05) were also seen in psychological and health symptom measures. Urinary pesticide metabolites were detected in pooled urine samples before the retreat and were undetectable after the retreat. Conclusion: Retreat experiences can lead to substantial improvements in multiple

Design of the DISCovery project: tailored work-oriented interventions to improve employee health, well-being, and performance-related outcomes in hospital care

PubMed Central

2013-01-01

Background It is well-known that health care workers in today’s general hospitals have to deal with high levels of job demands, which could have negative effects on their health, well-being, and job performance. A way to reduce job-related stress reactions and to optimize positive work-related outcomes is to raise the level of specific job resources and opportunities to recover from work. However, the question remains how to translate the optimization of the balance between job demands, job resources, and recovery opportunities into effective workplace interventions. The aim of the DISCovery project is to develop and implement tailored work-oriented interventions to improve health, well-being, and performance of health care personnel. Methods/Design A quasi-experimental field study with a non-equivalent control group pretest-posttest design will be conducted in a top general hospital. Four existing organizational departments will provide both an intervention and a comparison group. Two types of research methods are used: (1) a longitudinal web-based survey study, and (2) a longitudinal daily diary study. After base-line measures of both methods, existing and yet to be developed interventions will be implemented within the experimental groups. Follow-up measurements will be taken one and two years after the base-line measures to analyze short-term and long-term effects of the interventions. Additionally, a process evaluation and a cost-effectiveness analysis will be carried out. Discussion The DISCovery project fulfills a strong need for theory-driven and scientifically well-performed research on job stress and performance interventions. It will provide insight into (1) how a balance between job demands, job resources, and recovery from work can be optimized, (2) the short-term and long-term effects of tailored work-oriented effects, and (3) indicators for successful or unsuccessful implementation of interventions. PMID:23421647

How to build institutionalization on students: a pilot experiment on a didactical design of addition and subtraction involving negative integers

NASA Astrophysics Data System (ADS)

Fuadiah, N. F.; Suryadi, D.; Turmudi

2018-05-01

This study focuses on the design of a didactical situation in addition and subtraction involving negative integers at the pilot experiment phase. As we know, negative numbers become an obstacle for students in solving problems related to them. This study aims to create a didactical design that can assist students in understanding the addition and subtraction. Another expected result in this way is that students are introduced to the characteristics of addition and subtraction of integers. The design was implemented on 32 seventh grade students in one of the classes in a junior secondary school as the pilot experiment. Learning activities were observed thoroughly including the students’ responses that emerged during the learning activities. The written documentation of the students was also used to support the analysis in the learning activities. The results of the analysis showed that this method could help the students perform a large number of integer operations that could not be done with a number line. The teacher’s support as a didactical potential contract was still needed to encourage institutionalization processes. The results of the design analysis used as the basis of the revision are expected to be implemented by the teacher in the teaching experiment.

Mechanical characterization of structurally porous biomaterials built via additive manufacturing: experiments, predictive models, and design maps for load-bearing bone replacement implants.

PubMed

Melancon, D; Bagheri, Z S; Johnston, R B; Liu, L; Tanzer, M; Pasini, D

2017-11-01

Porous biomaterials can be additively manufactured with micro-architecture tailored to satisfy the stringent mechano-biological requirements imposed by bone replacement implants. In a previous investigation, we introduced structurally porous biomaterials, featuring strength five times stronger than commercially available porous materials, and confirmed their bone ingrowth capability in an in vivo canine model. While encouraging, the manufactured biomaterials showed geometric mismatches between their internal porous architecture and that of its as-designed counterpart, as well as discrepancies between predicted and tested mechanical properties, issues not fully elucidated. In this work, we propose a systematic approach integrating computed tomography, mechanical testing, and statistical analysis of geometric imperfections to generate statistical based numerical models of high-strength additively manufactured porous biomaterials. The method is used to develop morphology and mechanical maps that illustrate the role played by pore size, porosity, strut thickness, and topology on the relations governing their elastic modulus and compressive yield strength. Overall, there are mismatches between the mechanical properties of ideal-geometry models and as-manufactured porous biomaterials with average errors of 49% and 41% respectively for compressive elastic modulus and yield strength. The proposed methodology gives more accurate predictions for the compressive stiffness and the compressive strength properties with a reduction of the average error to 11% and 7.6%. The implications of the results and the methodology here introduced are discussed in the relevant biomechanical and clinical context, with insight that highlights promises and limitations of additively manufactured porous biomaterials for load-bearing bone replacement implants. In this work, we perform mechanical characterization of load-bearing porous biomaterials for bone replacement over their entire design

A study of the temporal variability of atrazine in private well water. part ii: analysis of data

USGS Publications Warehouse

Pinsky, Paul; Lorber, Matthew; Johnson, Kent; Kross, Burton; Burmeister, Leon; Wilkins, Amina; Hallberg, George

1997-01-01

In 1988, the Iowa Department of Natural Resources, along withthe University of Iowa, conducted the Statewide Rural WellWater Survey, commonly known as SWRL. A total of 686private rural drinking water wells was selected by use of aprobability sample and tested for pesticides and nitrate. A subsetof these wells, the 10% repeat wells, were additionally sampledin October, 1990 and June, 1991. Starting in November, 1991,the University of Iowa, with sponsorship from the United StatesEnvironmental Protection Agency, revisited the 10% repeat wellsto begin a study of the temporal variability of atrazine and nitratein wells. Other wells, which had originally tested positive foratrazine in SWRL but were not in the 10% population, wereadded to the study population. Temporal sampling for a year-long period began in February of 1992 and concluded in Januaryof 1993. All wells were sampled monthly, a subset was sampledweekly, and a second subset was sampled for 14 day consecutiveperiods. Of the 67 wells in the 10% population tested monthly,7 (10.4%) tested positive for atrazine at least once during theyear, and 3 (4%) were positive each of the 12 months. Theaverage concentration in the 7 wells was 0.10 µg/L. Fornitrate, 15 (22%) wells in the 10% repeat population monthlysampling were above the Maximum Contaminant Level of 10 mg/L at least once. This paper, the second of two papers on thisstudy, describes the analysis of data from the survey. The firstpaper (Lorber et al., 1997) reviews the study design, theanalytical methodologies, and development of the data base.

Additively Manufactured and Surface Biofunctionalized Porous Nitinol.

PubMed

Gorgin Karaji, Z; Speirs, M; Dadbakhsh, S; Kruth, J-P; Weinans, H; Zadpoor, A A; Amin Yavari, S

2017-01-18

Enhanced bone tissue regeneration and improved osseointegration are among the most important goals in design of multifunctional orthopedic biomaterials. In this study, we used additive manufacturing (selective laser melting) to develop multifunctional porous nitinol that combines superelasticity with a rationally designed microarchitecture and biofunctionalized surface. The rational design based on triply periodic minimal surfaces aimed to properly adjust the pore size, increase the surface area (thereby amplifying the effects of surface biofunctionalization), and resemble the curvature characteristics of trabecular bone. The surface of additively manufactured (AM) porous nitinol was biofunctionalized using polydopamine-immobilized rhBMP2 for better control of the release kinetics. The actual morphological properties of porous nitinol measured by microcomputed tomography (e.g., open/close porosity, and surface area) closely matched the design values. The superelasticity originated from the austenite phase formed in the nitinol porous structure at room temperature. Polydopamine and rhBMP2 signature peaks were confirmed by X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy tests. The release of rhBMP2 continued until 28 days. The early time and long-term release profiles were found to be adjustable independent of each other. In vitro cell culture showed improved cell attachment, cell proliferation, cell morphology (spreading, spindle-like shape), and cell coverage as well as elevated levels of ALP activity and increased calcium content for biofunctionalized surfaces as compared to as-manufactured specimens. The demonstrated functionalities of porous nitinol could be used as a basis for deployable orthopedic implants with rationally designed microarchitectures that maximize bone tissue regeneration performance by release of biomolecules with adjustable and well-controlled release profiles.

A Novel Multiscale Design of Interfaces for Polymeric Composites and Bonded Joints using Additive Manufacturing

DTIC Science & Technology

2016-09-13

AFRL-AFOSR-VA-TR-2016-0317 A Novel Multiscale Design of Interfaces for Polymeric Composites and Bonded Joints using Additive Manufacturing Pavana...Composites and Bonded Joints using Additive Manufacturing AWARD NO.: FA9550-15-1-0216 AGENCY NAME: The Air Force Office of Scientific Research (AFOSR), Ar...20 3 Additive Manufacturing for Bonded Composite Joints 21 3.1 Introduction

Developing design methods of concrete mix with microsilica additives for road construction

NASA Astrophysics Data System (ADS)

Dmitrienko, Vladimir; Shrivel, Igor; Kokunko, Irina; Pashkova, Olga

2017-10-01

Based on the laboratory test results, regression equations having standard cone and concrete strength, to determine the available amount of cement, water and microsilica were obtained. The joint solution of these equations allowed the researchers to develop the algorithm of designing heavy concrete compositions with microsilica additives for road construction.

Design Optimization of Irregular Cellular Structure for Additive Manufacturing

NASA Astrophysics Data System (ADS)

Song, Guo-Hua; Jing, Shi-Kai; Zhao, Fang-Lei; Wang, Ye-Dong; Xing, Hao; Zhou, Jing-Tao

2017-09-01

Irregularcellular structurehas great potential to be considered in light-weight design field. However, the research on optimizing irregular cellular structures has not yet been reporteddue to the difficulties in their modeling technology. Based on the variable density topology optimization theory, an efficient method for optimizing the topology of irregular cellular structures fabricated through additive manufacturing processes is proposed. The proposed method utilizes tangent circles to automatically generate the main outline of irregular cellular structure. The topological layoutof each cellstructure is optimized using the relative density informationobtained from the proposed modified SIMP method. A mapping relationship between cell structure and relative densityelement is builtto determine the diameter of each cell structure. The results show that the irregular cellular structure can be optimized with the proposed method. The results of simulation and experimental test are similar for irregular cellular structure, which indicate that the maximum deformation value obtained using the modified Solid Isotropic Microstructures with Penalization (SIMP) approach is lower 5.4×10-5 mm than that using the SIMP approach under the same under the same external load. The proposed research provides the instruction to design the other irregular cellular structure.

Well installation, single-well testing, and particle-size analysis for selected sites in and near the Lost Creek Designated Ground Water Basin, north-central Colorado, 2003-2004

USGS Publications Warehouse

Beck, Jennifer A.; Paschke, Suzanne S.; Arnold, L. Rick

2011-01-01

Ground Water Basin generally were greater than hydraulic-conductivity values for the Denver Formation sandstone aquifer and less than hydraulic-conductivity values for the alluvial aquifer along the main stem of the South Platte River Basin reported by previous studies. Particle sizes were analyzed for a total of 14 samples of material representative of the screened interval in each of the 14 wells tested in this study. Of the 14 samples collected, 8 samples represent the alluvial aquifer and 6 samples represent the Denver Formation sandstone aquifer in and near the Lost Creek Designated Ground Water Basin. The sampled alluvial aquifer material generally contained a greater percentage of large particles (larger than 0.5 mm) than the sampled sandstone aquifer material. Alternatively, the sampled sandstone aquifer material generally contained a greater percentage of fine particles (smaller than 0.5 mm) than the sampled alluvial aquifer material consistent with the finding that the alluvial aquifer is more conductive than the sandstone aquifer in the vicinity of the Lost Creek Designated Ground Water Basin.

Analysis of Latest Experience in Design of Industrial Buildings Reconstruction by Constructing Additional Interfloor Overlaps

NASA Astrophysics Data System (ADS)

Peshnina, I.; Sinitsina, O.

2017-11-01

The study relevance is determined by the increasing interest in reconstruction of city historical centers and located in the area of industrial buildings the functional profile of which needs to be changed. The problem of obtaining extra usable spaces in the historical centers of cities is solved by raising the number of storeys in the buildings which can be achieved by the construction of additional built-in inter-floor overlaps. The article is dedicated to the analysis of the recent years’ experience in reconstruction design involving this method in our country and abroad, in the Netherlands, in particular. The article presents the results of the analysis of the experience in reconstruction of the objects by constructing additional inter-floor overlaps and aims to define the optimum construction solution for built-in inter-floor overlapping and to develop non-existing solutions for wide application of this method in the reconstruction of a building with non-unified and unmodulated parameters. It was determined as expedient to apply a monolith reinforced concrete slab with the use of steel profiled flooring as a formwork and reinforcement and steel beams designed as “Built-in Beams” for the construction of built-in inter-floor overlaps in reconstruction. The article will be useful for specialists doing research in the sphere of reconstruction of the buildings and for the practical activity of design engineers.

Monitoring-well network and sampling design for ground-water quality, Wind River Indian Reservation, Wyoming

USGS Publications Warehouse

Mason, Jon P.; Sebree, Sonja K.; Quinn, Thomas L.

2005-01-01

The Wind River Indian Reservation, located in parts of Fremont and Hot Springs Counties, Wyoming, has a total land area of more than 3,500 square miles. Ground water on the Wind River Indian Reservation is a valuable resource for Shoshone and Northern Arapahoe tribal members and others who live on the Reservation. There are many types of land uses on the Reservation that have the potential to affect the quality of ground-water resources. Urban areas, rural housing developments, agricultural lands, landfills, oil and natural gas fields, mining, and pipeline utility corridors all have the potential to affect ground-water quality. A cooperative study was developed between the U.S. Geological Survey and the Wind River Environmental Quality Commission to identify areas of the Reservation that have the highest potential for ground-water contamination and develop a comprehensive plan to monitor these areas. An arithmetic overlay model for the Wind River Indian Reservation was created using seven geographic information system data layers representing factors with varying potential to affect ground-water quality. The data layers used were: the National Land Cover Dataset, water well density, aquifer sensitivity, oil and natural gas fields and petroleum pipelines, sites with potential contaminant sources, sites that are known to have ground-water contamination, and National Pollutant Discharge Elimination System sites. A prioritization map for monitoring ground-water quality on the Reservation was created using the model. The prioritization map ranks the priority for monitoring ground-water quality in different areas of the Reservation as low, medium, or high. To help minimize bias in selecting sites for a monitoring well network, an automated stratified random site-selection approach was used to select 30 sites for ground-water quality monitoring within the high priority areas. In addition, the study also provided a sampling design for constituents to be monitored, sampling

Well-planning programs give students field-like experience

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sifferman, T.R.; Chapman, L.

1983-01-01

The University of Tulsa recently was given a package of computer well planning and drilling programs that will enable petroleum engineering students to gain valuable experience in designing well programs while still in school. Comprehensive homework assignments are now given in areas of drilling fluids programing, hydraulics, directional wells and surveying. Additional programs are scheduled for next semester.

How system designers think: a study of design thinking in human factors engineering.

PubMed

Papantonopoulos, Sotiris

2004-11-01

The paper presents a descriptive study of design thinking in human factors engineering. The objective of the study is to analyse the role of interpretation in design thinking and the role of design practice in guiding interpretation. The study involved 10 system designers undertaking the allocation of cognitive functions in three production planning and control task scenarios. Allocation decisions were recorded and verbal protocols of the design process were collected to elicit the subjects' thought processes. Verbal protocol analysis showed that subjects carried out the design of cognitive task allocation as a problem of applying a selected automation technology from their initial design deliberations. This design strategy stands in contrast to the predominant view of system design that stipulates that user requirements should be thoroughly analysed prior to making any decisions about technology. Theoretical frameworks from design research and ontological design showed that the system design process may be better understood by recognizing the role of design hypotheses in system design, as well as the diverse interactions between interpretation and practice, means and ends, and design practice and the designer's pre-understanding which shape the design process. Ways to balance the bias exerted on the design process were discussed.

EPA Hydraulic Fracturing Study Technical Workshop #2 March 10-11, 2011: Well Integrity Case Study by Lloyd H. Hetrick

EPA Pesticide Factsheets

This case study defines well integrity by the prevention of vertical migration of fluids to protect drinking water resources. A generic shale development well is presented, including design, construction, operational phase, and its plug and abandonment.

An Investigation of the Additive Benefits of Parent Dialogic Reading Techniques in Older Preschool Children

ERIC Educational Resources Information Center

Switalski, Sarah O'Neill

2012-01-01

This study examined the additive benefit of parent dialogic reading techniques in older, high-risk preschool children using multiple baseline design across participants, a single subject research design, as was as well as pre-test and post-test measures. Five preschoolers age-eligible to begin kindergarten the following school year participated.…

Newberry Well 55-29 Stimulation Data 2014

DOE Data Explorer

Trenton T. Cladouhos

2015-09-03

The Newberry Volcano EGS Demonstration in central Oregon, a 5 year project begun in 2010, tests recent technological advances designed to reduce the cost of power generated by EGS in a hot, dry well (NWG 55-29) drilled in 2008. First, the stimulation pumps used were designed to run for weeks and deliver large volumes of water at moderate well-head pressure. Second, to stimulate multiple zones, AltaRock developed thermo-degradable zonal isolation materials (TZIMs) to seal off fractures in a geothermal well to stimulate secondary and tertiary fracture zones. The TZIMs degrade within weeks, resulting in an optimized injection/ production profile of the entire well. Third, the project followed a project-specific Induced Seismicity Mitigation Plan (ISMP) to evaluate, monitor for, and mitigate felt induced seismicity. An initial stimulation was conducted in 2012 and continued for 7 weeks, with over 41,000 m3 of water injected. Further analysis indicated a shallow casing leak and an unstable formation in the open hole. The well was repaired with a shallow casing tieback and perforated liner in the open hole and re-stimulated in 2014. The second stimulation started September 23rd, 2014 and continued for 3 weeks with over 9,500 m3 of water injected. The well was treated with several batches of newly tested TZIM diverter materials and a newly designed Diverter Injection Vessel Assembly (DIVA), which was the main modification to the original injection system design used in 2012. A second round of stimulation that included two perforation shots and additional batches of TZIM was conducted on November 11th, 2014 for 9 days with an additional 4,000 m3 of water injected. The stimulations resulted in a 3-4 fold increase in injectivity, and PTS data indicates partial blocking and creation of flow zones near the bottom of the well.

Effect of silica-palm shell carbon composite additive in enhancing the strength of the concrete in the oil-well cementing job

NASA Astrophysics Data System (ADS)

Novriansyah, A.; Mursyidah, U.; Novrianti; Putri, S. S.; Riswati, S. S.

2018-04-01

This study provides an analysis of composite additive effect to concrete’s strength in the oil-well cementing job. The composite additive is originated from the nano-sized form of silica and charcoal from palm shell waste. The quality of the concrete will be determined from its porosity, compressive strength, and shear bond strength parameters. Those parameters must be reliable base on the most respectable standards in oil and gas industry, in this study we use the standard from American Petroleum Institute (API). Six concrete samples with different concentration will be tested to obtain these parameters. The result from the test shown a decrement trend of the porosity while the concentration is increased. In contrast, the highest values of compressive strength and shear bond strength are obtained from the sample with higher additive concentration. The optimum strength was obtained in sample with 0.02% The results become clearly proven through verification by scanning electron image where the additive has successfully fill the voids in the concrete’s sample, resulting in strength enhancement of the sample.

From path models to commands during additive printing of large-scale architectural designs

NASA Astrophysics Data System (ADS)

Chepchurov, M. S.; Zhukov, E. M.; Yakovlev, E. A.; Matveykin, V. G.

2018-05-01

The article considers the problem of automation of the formation of large complex parts, products and structures, especially for unique or small-batch objects produced by a method of additive technology [1]. Results of scientific research in search for the optimal design of a robotic complex, its modes of operation (work), structure of its control helped to impose the technical requirements on the technological process for manufacturing and design installation of the robotic complex. Research on virtual models of the robotic complexes allowed defining the main directions of design improvements and the main goal (purpose) of testing of the the manufactured prototype: checking the positioning accuracy of the working part.

A design study to develop young children's understanding of multiplication and division

NASA Astrophysics Data System (ADS)

Bicknell, Brenda; Young-Loveridge, Jenny; Nguyen, Nhung

2016-12-01

This design study investigated the use of multiplication and division problems to help 5-year-old children develop an early understanding of multiplication and division. One teacher and her class of 15 5-year-old children were involved in a collaborative partnership with the researchers. The design study was conducted over two 4-week periods in May-June and October-November. The focus in this article is on three key aspects of classroom teaching: instructional tasks, the use of representations, and discourse, including the mathematics register. Results from selected pre- and post-assessment tasks within a diagnostic interview showed that there were improvements in addition and subtraction as well as multiplication and division, even though the teaching had used multiplication and division problems. Students made progress on all four operational domains, with effect sizes ranging from approximately two thirds of a standard deviation to 2 standard deviations. Most of the improvement in students' number strategies was in moving from `counting all' to `counting on' and `skip counting'. The findings challenge the idea that learning experiences in addition and subtraction should precede those in multiplication and division as suggested in some curriculum documents.

Modeling of mixing in 96-well microplates observed with fluorescence indicators.

PubMed

Weiss, Svenja; John, Gernot T; Klimant, Ingo; Heinzle, Elmar

2002-01-01

Mixing in 96-well microplates was studied using soluble pH indicators and a fluorescence pH sensor. Small amounts of alkali were added with the aid of a multichannel pipet, a piston pump, and a piezoelectric actuator. Mixing patterns were observed visually using a video camera. Addition of drops each of about 1 nL with the piezoelectric actuator resulted in umbrella and double-disklike shapes. Convective mixing was mainly observed in the upper part of the well, whereas the lower part was only mixed quickly when using the multichannel pipet and the piston pump with an addition volume of 5 microL or larger. Estimated mixing times were between a few seconds and several minutes. Mixing by liquid dispensing was much more effective than by shaking. A mixing model consisting of 21 elements could describe mixing dynamics observed by the dissolved fluorescence dye and by the optical immobilized pH sensor. This model can be applied for designing pH control in microplates or for design of kinetic experiments with liquid addition.

Vaccine stability study design and analysis to support product licensure.

PubMed

Schofield, Timothy L

2009-11-01

Stability evaluation supporting vaccine licensure includes studies of bulk intermediates as well as final container product. Long-term and accelerated studies are performed to support shelf life and to determine release limits for the vaccine. Vaccine shelf life is best determined utilizing a formal statistical evaluation outlined in the ICH guidelines, while minimum release is calculated to help assure adequate potency through handling and storage of the vaccine. In addition to supporting release potency determination, accelerated stability studies may be used to support a strategy to recalculate product expiry after an unintended temperature excursion such as a cold storage unit failure or mishandling during transport. Appropriate statistical evaluation of vaccine stability data promotes strategic stability study design, in order to reduce the uncertainty associated with the determination of the degradation rate, and the associated risk to the customer.

Evaluation of agile designs in first-in-human (FIH) trials--a simulation study.

PubMed

Perlstein, Itay; Bolognese, James A; Krishna, Rajesh; Wagner, John A

2009-12-01

The aim of the investigation was to evaluate alternatives to standard first-in-human (FIH) designs in order to optimize the information gained from such studies by employing novel agile trial designs. Agile designs combine adaptive and flexible elements to enable optimized use of prior information either before and/or during conduct of the study to seamlessly update the study design. A comparison of the traditional 6 + 2 (active + placebo) subjects per cohort design with alternative, reduced sample size, agile designs was performed by using discrete event simulation. Agile designs were evaluated for specific adverse event models and rates as well as dose-proportional, saturated, and steep-accumulation pharmacokinetic profiles. Alternative, reduced sample size (hereafter referred to as agile) designs are proposed for cases where prior knowledge about pharmacokinetics and/or adverse event relationships are available or appropriately assumed. Additionally, preferred alternatives are proposed for a general case when prior knowledge is limited or unavailable. Within the tested conditions and stated assumptions, some agile designs were found to be as efficient as traditional designs. Thus, simulations demonstrated that the agile design is a robust and feasible approach to FIH clinical trials, with no meaningful loss of relevant information, as it relates to PK and AE assumptions. In some circumstances, applying agile designs may decrease the duration and resources required for Phase I studies, increasing the efficiency of early clinical development. We highlight the value and importance of useful prior information when specifying key assumptions related to safety, tolerability, and PK.

Mechanics of additively manufactured biomaterials.

PubMed

Zadpoor, Amir A

2017-06-01

Additive manufacturing (3D printing) has found many applications in healthcare including fabrication of biomaterials as well as bioprinting of tissues and organs. Additively manufactured (AM) biomaterials may possess arbitrarily complex micro-architectures that give rise to novel mechanical, physical, and biological properties. The mechanical behavior of such porous biomaterials including their quasi-static mechanical properties and fatigue resistance is not yet well understood. It is particularly important to understand the relationship between the designed micro-architecture (topology) and the resulting mechanical properties. The current special issue is dedicated to understanding the mechanical behavior of AM biomaterials. Although various types of AM biomaterials are represented in the special issue, the primary focus is on AM porous metallic biomaterials. As a prelude to this special issue, this editorial reviews some of the latest findings in the mechanical behavior of AM porous metallic biomaterials so as to describe the current state-of-the-art and set the stage for the other studies appearing in the issue. Some areas that are important for future research are also briefly mentioned. Copyright © 2017 Elsevier Ltd. All rights reserved.

Bayesian Optimal Interval Design: A Simple and Well-Performing Design for Phase I Oncology Trials

PubMed Central

Yuan, Ying; Hess, Kenneth R.; Hilsenbeck, Susan G.; Gilbert, Mark R.

2016-01-01

Despite more than two decades of publications that offer more innovative model-based designs, the classical 3+3 design remains the most dominant phase I trial design in practice. In this article, we introduce a new trial design, the Bayesian optimal interval (BOIN) design. The BOIN design is easy to implement in a way similar to the 3+3 design, but is more flexible for choosing the target toxicity rate and cohort size and yields a substantially better performance that is comparable to that of more complex model-based designs. The BOIN design contains the 3+3 design and the accelerated titration design as special cases, thus linking it to established phase I approaches. A numerical study shows that the BOIN design generally outperforms the 3+3 design and the modified toxicity probability interval (mTPI) design. The BOIN design is more likely than the 3+3 design to correctly select the maximum tolerated dose (MTD) and allocate more patients to the MTD. Compared to the mTPI design, the BOIN design has a substantially lower risk of overdosing patients and generally a higher probability of correctly selecting the MTD. User-friendly software is freely available to facilitate the application of the BOIN design. PMID:27407096

Automated microbial metabolism laboratory. [design of advanced labeled release experiment based on single addition of soil and multiple sequential additions of media into test chambers

NASA Technical Reports Server (NTRS)

1974-01-01

The design and rationale of an advanced labeled release experiment based on single addition of soil and multiple sequential additions of media into each of four test chambers are outlined. The feasibility for multiple addition tests was established and various details of the methodology were studied. The four chamber battery of tests include: (1) determination of the effect of various atmospheric gases and selection of that gas which produces an optimum response; (2) determination of the effect of incubation temperature and selection of the optimum temperature for performing Martian biochemical tests; (3) sterile soil is dosed with a battery of C-14 labeled substrates and subjected to experimental temperature range; and (4) determination of the possible inhibitory effects of water on Martian organisms is performed initially by dosing with 0.01 ml and 0.5 ml of medium, respectively. A series of specifically labeled substrates are then added to obtain patterns in metabolic 14CO2 (C-14)O2 evolution.

Just-in-time Design and Additive Manufacture of Patient-specific Medical Implants

NASA Astrophysics Data System (ADS)

Shidid, Darpan; Leary, Martin; Choong, Peter; Brandt, Milan

Recent advances in medical imaging and manufacturing science have enabled the design and production of complex, patient-specific orthopaedic implants. Additive Manufacture (AM) generates three-dimensional structures layer by layer, and is not subject to the constraints associated with traditional manufacturing methods. AM provides significant opportunities for the design of novel geometries and complex lattice structures with enhanced functional performance. However, the design and manufacture of patient-specific AM implant structures requires unique expertise in handling various optimization platforms. Furthermore, the design process for complex structures is computationally intensive. The primary aim of this research is to enable the just-in-time customisation of AM prosthesis; whereby AM implant design and manufacture be completed within the time constraints of a single surgical procedure, while minimising prosthesis mass and optimising the lattice structure to match the stiffness of the surrounding bone tissue. In this research, a design approach using raw CT scan data is applied to the AM manufacture of femoral prosthesis. Using the proposed just-in-time concept, the mass of the prosthesis was rapidly designed and manufactured while satisfying the associated structural requirements. Compressive testing of lattice structures manufactured using proposed method shows that the load carrying capacity of the resected composite bone can be recovered by up to 85% and the compressive stiffness of the AM prosthesis is statistically indistinguishable from the stiffness of the initial bone.

76 FR 3907 - Designation of a Class of Employees for Addition to the Special Exposure Cohort

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-21

... addition to the SEC: All Atomic Weapons Employer employees who worked at Texas City Chemicals, Inc., from... designate a class of employees from Texas City Chemicals, Inc., Texas City, Texas, as an addition to the...

Effectiveness of additional self-care acupressure for women with menstrual pain compared to usual care alone: using stakeholder engagement to design a pragmatic randomized trial and study protocol.

PubMed

Blödt, Susanne; Schützler, Lena; Huang, Wenjing; Pach, Daniel; Brinkhaus, Benno; Hummelsberger, Josef; Kirschbaum, Barbara; Kuhlmann, Kirsten; Lao, Lixing; Liang, Fanrong; Mietzner, Anna; Mittring, Nadine; Müller, Sabine; Paul, Anna; Pimpao-Niederle, Carolina; Roll, Stephanie; Wu, Huangan; Zhu, Jiang; Witt, Claudia M

2013-04-11

Self-care acupressure might be successful in treating menstrual pain, which is common among young women. There is a need for comparative effectiveness research with stakeholder engagement in all phases seeking to address the needs of decision-makers. Our aim was to design a study on the effectiveness of additional self-care acupressure for menstrual pain comparing usual care alone using different methods of stakeholder engagement. The study was designed using multiple mixed methods for stakeholder engagement. Based on the results of a survey and focus group discussion, a stakeholder advisory group developed the study design. Stakeholder engagement resulted in a two-arm pragmatic randomized trial. Two hundred and twenty women aged 18 to 25 years with menstrual pain will be included in the study. Outcome measurement will be done using electronic questionnaires provided by a study specific mobile application (App). Primary outcome will be the mean pain intensity at the days of pain during the third menstruation after therapy start. Stakeholder engagement helped to develop a study design that better serves the needs of decision makers, including an App as a modern tool for both intervention and data collection in a young target group. Clinicaltrials.gov identifier http://NCT01582724.

MASTOS: Mammography Simulation Tool for design Optimization Studies.

PubMed

Spyrou, G; Panayiotakis, G; Tzanakos, G

2000-01-01

Mammography is a high quality imaging technique for the detection of breast lesions, which requires dedicated equipment and optimum operation. The design parameters of a mammography unit have to be decided and evaluated before the construction of such a high cost of apparatus. The optimum operational parameters also must be defined well before the real breast examination. MASTOS is a software package, based on Monte Carlo methods, that is designed to be used as a simulation tool in mammography. The input consists of the parameters that have to be specified when using a mammography unit, and also the parameters specifying the shape and composition of the breast phantom. In addition, the input may specify parameters needed in the design of a new mammographic apparatus. The main output of the simulation is a mammographic image and calculations of various factors that describe the image quality. The Monte Carlo simulation code is PC-based and is driven by an outer shell of a graphical user interface. The entire software package is a simulation tool for mammography and can be applied in basic research and/or in training in the fields of medical physics and biomedical engineering as well as in the performance evaluation of new designs of mammography units and in the determination of optimum standards for the operational parameters of a mammography unit.

Additional cash incentive within a conditional cash transfer scheme: a 'controlled before and during' design evaluation study from India.

PubMed

Lahariya, Chandrakant; Mishra, Ashok; Nandan, Deoki; Gautam, Praveen; Gupta, Sanjay

2011-01-01

Conditional Cash Transfer (CCT) schemes have shown largely favorable changes in the health seeking behavior. This evaluation study assesses the process and performance of an Additional Cash Incentive (ACI) scheme within an ongoing CCT scheme in India, and document lessons. A controlled before and during design study was conducted in Madhya Pradesh state of India, from August 2007 to March 2008, with increased in institutional deliveries as a primary outcome. In depth interviews, focus group discussions and household surveys were done for data collection. Lack of awareness about ACI scheme amongst general population and beneficiaries, cumbersome cash disbursement procedure, intricate eligibility criteria, extensive paper work, and insufficient focus on community involvement were the major implementation challenges. There were anecdotal reports of political interference and possible scope for corruption. At the end of implementation period, overall rate of institutional deliveries had increased in both target and control populations; however, the differences were not statistically significant. No cause and effect association could be proven by this study. Poor planning and coordination, and lack of public awareness about the scheme resulted in low utilization. Thus, proper IEC and training, detailed implementation plan, orientation training for implementer, sufficient budgetary allocation, and community participation should be an integral part for successful implementation of any such scheme. The lesson learned this evaluation study may be useful in any developing country setting and may be utilized for planning and implementation of any ACI scheme in future.

Bayesian Optimal Interval Design: A Simple and Well-Performing Design for Phase I Oncology Trials.

PubMed

Yuan, Ying; Hess, Kenneth R; Hilsenbeck, Susan G; Gilbert, Mark R

2016-09-01

Despite more than two decades of publications that offer more innovative model-based designs, the classical 3 + 3 design remains the most dominant phase I trial design in practice. In this article, we introduce a new trial design, the Bayesian optimal interval (BOIN) design. The BOIN design is easy to implement in a way similar to the 3 + 3 design, but is more flexible for choosing the target toxicity rate and cohort size and yields a substantially better performance that is comparable with that of more complex model-based designs. The BOIN design contains the 3 + 3 design and the accelerated titration design as special cases, thus linking it to established phase I approaches. A numerical study shows that the BOIN design generally outperforms the 3 + 3 design and the modified toxicity probability interval (mTPI) design. The BOIN design is more likely than the 3 + 3 design to correctly select the MTD and allocate more patients to the MTD. Compared with the mTPI design, the BOIN design has a substantially lower risk of overdosing patients and generally a higher probability of correctly selecting the MTD. User-friendly software is freely available to facilitate the application of the BOIN design. Clin Cancer Res; 22(17); 4291-301. ©2016 AACR. ©2016 American Association for Cancer Research.

13 CFR 108.1940 - Procedures for designation of additional Low-Income Geographic Areas

Code of Federal Regulations, 2010 CFR

2010-01-01

... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Procedures for designation of additional Low-Income Geographic Areas 108.1940 Section 108.1940 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION NEW MARKETS VENTURE CAPITAL (âNMVCâ) PROGRAM Miscellaneous § 108.1940 Procedures...

Optimized, Budget-constrained Monitoring Well Placement Using DREAM

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yonkofski, Catherine M. R.; Davidson, Casie L.; Rodriguez, Luke R.

Defining the ideal suite of monitoring technologies to be deployed at a carbon capture and storage (CCS) site presents a challenge to project developers, financers, insurers, regulators and other stakeholders. The monitoring, verification, and accounting (MVA) toolkit offers a suite of technologies to monitor an extensive range of parameters across a wide span of spatial and temporal resolutions, each with their own degree of sensitivity to changes in the parameter being monitored. Understanding how best to optimize MVA budgets to minimize the time to leak detection could help to address issues around project risks, and in turn help support broadmore » CCS deployment. This paper presents a case study demonstrating an application of the Designs for Risk Evaluation and Management (DREAM) tool using an ensemble of CO 2 leakage scenarios taken from a previous study on leakage impacts to groundwater. Impacts were assessed and monitored as a function of pH, total dissolved solids (TDS), and trace metal concentrations of arsenic (As), cadmium (Cd), chromium (Cr), and lead (Pb). Using output from the previous study, DREAM was used to optimize monitoring system designs based on variable sampling locations and parameters. The algorithm requires the user to define a finite budget to limit the number of monitoring wells and technologies deployed, and then iterates well placement and sensor type and location until it converges on the configuration with the lowest time to first detection of the leak averaged across all scenarios. To facilitate an understanding of the optimal number of sampling wells, DREAM was used to assess the marginal utility of additional sampling locations. Based on assumptions about monitoring costs and replacement costs of degraded water, the incremental cost of each additional sampling well can be compared against its marginal value in terms of avoided aquifer degradation. Applying this method, DREAM identified the most cost-effective ensemble with 14

Optimized, Budget-constrained Monitoring Well Placement Using DREAM

DOE PAGES

Yonkofski, Catherine M. R.; Davidson, Casie L.; Rodriguez, Luke R.; ...

2017-08-18

Defining the ideal suite of monitoring technologies to be deployed at a carbon capture and storage (CCS) site presents a challenge to project developers, financers, insurers, regulators and other stakeholders. The monitoring, verification, and accounting (MVA) toolkit offers a suite of technologies to monitor an extensive range of parameters across a wide span of spatial and temporal resolutions, each with their own degree of sensitivity to changes in the parameter being monitored. Understanding how best to optimize MVA budgets to minimize the time to leak detection could help to address issues around project risks, and in turn help support broadmore » CCS deployment. This paper presents a case study demonstrating an application of the Designs for Risk Evaluation and Management (DREAM) tool using an ensemble of CO 2 leakage scenarios taken from a previous study on leakage impacts to groundwater. Impacts were assessed and monitored as a function of pH, total dissolved solids (TDS), and trace metal concentrations of arsenic (As), cadmium (Cd), chromium (Cr), and lead (Pb). Using output from the previous study, DREAM was used to optimize monitoring system designs based on variable sampling locations and parameters. The algorithm requires the user to define a finite budget to limit the number of monitoring wells and technologies deployed, and then iterates well placement and sensor type and location until it converges on the configuration with the lowest time to first detection of the leak averaged across all scenarios. To facilitate an understanding of the optimal number of sampling wells, DREAM was used to assess the marginal utility of additional sampling locations. Based on assumptions about monitoring costs and replacement costs of degraded water, the incremental cost of each additional sampling well can be compared against its marginal value in terms of avoided aquifer degradation. Applying this method, DREAM identified the most cost-effective ensemble with 14

An Additive Manufacturing Test Artifact

PubMed Central

Moylan, Shawn; Slotwinski, John; Cooke, April; Jurrens, Kevin; Donmez, M Alkan

2014-01-01

A test artifact, intended for standardization, is proposed for the purpose of evaluating the performance of additive manufacturing (AM) systems. A thorough analysis of previously proposed AM test artifacts as well as experience with machining test artifacts have inspired the design of the proposed test artifact. This new artifact is designed to provide a characterization of the capabilities and limitations of an AM system, as well as to allow system improvement by linking specific errors measured in the test artifact to specific sources in the AM system. The proposed test artifact has been built in multiple materials using multiple AM technologies. The results of several of the builds are discussed, demonstrating how the measurement results can be used to characterize and improve a specific AM system. PMID:26601039

Promoting nutritional well-being in seniors: feasibility study of a nutrition information series.

PubMed

Manafò, Elizabeth; Jose, Katrina; Silverberg, Dena

2013-01-01

Better Living Health and Community Services developed a 12-week community-based nutrition information series (NIS) for people aged 55 or older. The purpose of this feasibility study was to describe briefly the process of developing and implementing the 12-week NIS and to identify the practicality and plausibility of the program in terms of its process and content attributes, using Thorncliffe Park community as the test site. A pre- and post-test design was used to identify changes in participants' perception of their nutritional and overall well-being. Twenty-four participants who completed at least four sessions participated in the post-evaluation follow-up. Only participants' perception of their eating habits demonstrated a significant, positive improvement (t24=2.1, P<0.05). The results suggest that the NIS has the potential to promote the health and well-being of community-living seniors. The development and implementation of the NIS provided considerations for program practicality. However, additional work is needed to examine the plausibility of the program in meeting its stated objective to promote awareness of nutrition as an important concept for healthy aging. Community-practising dietitians are instrumental in providing credible nutrition information to facilitate healthy eating in older Canadians.

Amino-Acid Network Clique Analysis of Protein Mutation Non-Additive Effects: A Case Study of Lysozme.

PubMed

Ming, Dengming; Chen, Rui; Huang, He

2018-05-10

Optimizing amino-acid mutations in enzyme design has been a very challenging task in modern bio-industrial applications. It is well known that many successful designs often hinge on extensive correlations among mutations at different sites within the enzyme, however, the underpinning mechanism for these correlations is far from clear. Here, we present a topology-based model to quantitively characterize non-additive effects between mutations. The method is based on the molecular dynamic simulations and the amino-acid network clique analysis. It examines if the two mutation sites of a double-site mutation fall into to a 3-clique structure, and associates such topological property of mutational site spatial distribution with mutation additivity features. We analyzed 13 dual mutations of T4 phage lysozyme and found that the clique-based model successfully distinguishes highly correlated or non-additive double-site mutations from those additive ones whose component mutations have less correlation. We also applied the model to protein Eglin c whose structural topology is significantly different from that of T4 phage lysozyme, and found that the model can, to some extension, still identify non-additive mutations from additive ones. Our calculations showed that mutation non-additive effects may heavily depend on a structural topology relationship between mutation sites, which can be quantitatively determined using amino-acid network k -cliques. We also showed that double-site mutation correlations can be significantly altered by exerting a third mutation, indicating that more detailed physicochemical interactions should be considered along with the network clique-based model for better understanding of this elusive mutation-correlation principle.

Structure Property Studies for Additively Manufactured Parts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Milenski, Helen M; Schmalzer, Andrew Michael; Kelly, Daniel

2015-08-17

Since the invention of modern Additive Manufacturing (AM) processes engineers and designers have worked hard to capitalize on the unique building capabilities that AM allows. By being able to customize the interior fill of parts it is now possible to design components with a controlled density and customized internal structure. The creation of new polymers and polymer composites allow for even greater control over the mechanical properties of AM parts. One of the key reasons to explore AM, is to bring about a new paradigm in part design, where materials can be strategically optimized in a way that conventional subtractivemore » methods cannot achieve. The two processes investigated in my research were the Fused Deposition Modeling (FDM) process and the Direct Ink Write (DIW) process. The objectives of the research were to determine the impact of in-fill density and morphology on the mechanical properties of FDM parts, and to determine if DIW printed samples could be produced where the filament diameter was varied while the overall density remained constant.« less

Interim Design Report for the International Design Study for a Neutrino Factory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Choubey, S.; Gandhi, R.; Goswami, S.

2011-10-01

The starting point for the International Design Study for the Neutrino Factory (the IDS-NF) was the output of the earlier International Scoping Study for a future Neutrino Factory and super-beam facility (the ISS). The accelerator facility described in section 2 incorporates the improvements that have been derived from the substantial amount of work carried out within the Accelerator Working Group. Highlights of these improvements include: (1) Initial concepts for the implementation of the proton driver at each of the three example sites, CERN, FNAL, and RAL; (2) Detailed studies of the energy deposition in the target area; (3) A reductionmore » in the length of the muon beam phase-rotation and bunching systems; (4) Detailed analyses of the impact of the risk that stray magnetic field in the accelerating cavities in the ionization cooling channel will reduce the maximum operating gradient. Several alternative ionization-cooling lattices have been developed as fallback options to mitigate this technical risk; (5) Studies of particle loss in the muon front-end and the development of strategies to mitigate the deleterious effects of such losses; (6) The development of more complete designs for the muon linac and re-circulating linacs; (7) The development of a design for the muon FFAG that incorporates insertions for injection and extraction; and (8) Detailed studies of diagnostics in the decay ring. Other sub-systems have undergone a more 'incremental' evolution; an indication that the design of the Neutrino Factory has achieved a degree of maturity. The design of the neutrino detectors described in section 3 has been optimized and the Detector Working Group has made substantial improvements to the simulation and analysis of the Magnetized Iron Neutrino Detector (MIND) resulting in an improvement in the overall neutrino-detection efficiency and a reduction in the neutrino-energy threshold. In addition, initial consideration of the engineering of the MIND has

DESIGN AND CALIBRATION OF THE EPA PM 2.5 WELL IMPACTOR NINETY-SIX (WINS)

EPA Science Inventory

The EPA well-type impactor ninety-six (WINS) was designed and calibrated to serve as a particle size separation device for the EPA reference method sampler for particulate matter under 2.5 um aerodynamic diameter. The WINS was designed to operate downstream of a PM10 inlet at a...

Long-Term Engagement in Formal Volunteering and Well-Being: An Exploratory Indian Study

PubMed Central

Elias, Jereesh K.; Sudhir, Paulomi; Mehrotra, Seema

2016-01-01

Sustained engagement in volunteering and its correlates have been examined in many studies across the globe. However, there is a dearth of research that explores the perspectives of long-term formal volunteers on the nature of changes perceived in oneself as a result of volunteering. Moreover, the linkages between psychological well-being and volunteering have been insufficiently explored. The present study was aimed at addressing these gaps. A heterogeneous sample of 20 long-term formal volunteer engaged in volunteering across different voluntary organisations in a southern metropolitan Indian city formed the primary sample for the study. In addition, a group of 21 short-term volunteers, matched on age, income and gender, was utilised for comparison with long-term volunteers on well-being indices. A semi structured interview schedule was used to explore self-perceived changes attributable to volunteering experience. In addition, a few standardised measures were used to comprehensively assess subjective well-being and psychological well-being. The interview data provided rich descriptions of perceived positive changes in self across cognitive, behavioral and emotional domains. Mirroring these patterns, the quantitative analyses indicated that long-term volunteers experienced higher levels of psychological well-being (sense of mastery and competence, self-acceptance and sense of engagement and growth) than short-term volunteers. The potential mechanisms involved in beneficial outcomes of long-term volunteering and implications for further research are highlighted. PMID:27690114

Long-Term Engagement in Formal Volunteering and Well-Being: An Exploratory Indian Study.

PubMed

Elias, Jereesh K; Sudhir, Paulomi; Mehrotra, Seema

2016-09-27

Sustained engagement in volunteering and its correlates have been examined in many studies across the globe. However, there is a dearth of research that explores the perspectives of long-term formal volunteers on the nature of changes perceived in oneself as a result of volunteering. Moreover, the linkages between psychological well-being and volunteering have been insufficiently explored. The present study was aimed at addressing these gaps. A heterogeneous sample of 20 long-term formal volunteer engaged in volunteering across different voluntary organisations in a southern metropolitan Indian city formed the primary sample for the study. In addition, a group of 21 short-term volunteers, matched on age, income and gender, was utilised for comparison with long-term volunteers on well-being indices. A semi structured interview schedule was used to explore self-perceived changes attributable to volunteering experience. In addition, a few standardised measures were used to comprehensively assess subjective well-being and psychological well-being. The interview data provided rich descriptions of perceived positive changes in self across cognitive, behavioral and emotional domains. Mirroring these patterns, the quantitative analyses indicated that long-term volunteers experienced higher levels of psychological well-being (sense of mastery and competence, self-acceptance and sense of engagement and growth) than short-term volunteers. The potential mechanisms involved in beneficial outcomes of long-term volunteering and implications for further research are highlighted.

10 CFR 60.132 - Additional design criteria for surface facilities in the geologic repository operations area.

Code of Federal Regulations, 2010 CFR

2010-01-01

... geologic repository operations area. 60.132 Section 60.132 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DISPOSAL OF HIGH-LEVEL RADIOACTIVE WASTES IN GEOLOGIC REPOSITORIES Technical Criteria Design Criteria for the Geologic Repository Operations Area § 60.132 Additional design criteria for surface facilities in...

Additive manufacturing of optical components

NASA Astrophysics Data System (ADS)

Heinrich, Andreas; Rank, Manuel; Maillard, Philippe; Suckow, Anne; Bauckhage, Yannick; Rößler, Patrick; Lang, Johannes; Shariff, Fatin; Pekrul, Sven

2016-08-01

The development of additive manufacturing methods has enlarged rapidly in recent years. Thereby, the work mainly focuses on the realization of mechanical components, but the additive manufacturing technology offers a high potential in the field of optics as well. Owing to new design possibilities, completely new solutions are possible. This article briefly reviews and compares the most important additive manufacturing methods for polymer optics. Additionally, it points out the characteristics of additive manufactured polymer optics. Thereby, surface quality is of crucial importance. In order to improve it, appropriate post-processing steps are necessary (e.g. robot polishing or coating), which will be discussed. An essential part of this paper deals with various additive manufactured optical components and their use, especially in optical systems for shape metrology (e.g. borehole sensor, tilt sensor, freeform surface sensor, fisheye lens). The examples should demonstrate the potentials and limitations of optical components produced by additive manufacturing.

APPROACHES TO GEOMETRIC DATA ANALYSIS ON BIG AREA ADDITIVELY MANUFACTURED (BAAM) PARTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dreifus, Gregory D; Ally, Nadya R; Post, Brian K

The promise of additive manufacturing is that a user can design and print complex geometries that are very difficult, if not impossible, to machine. The capabilities of 3D printing are restricted by a number of factors, including properties of the build material, time constraints, and geometric design restrictions. In this paper, a thorough accounting and study of the geometric restrictions that exist in the current iteration of additive manufacturing (AM) fused deposition modeling (FDM) technologies are discussed. Offline and online methodologies for collecting data sets for qualitative analysis of large scale AM, in particular Oak Ridge National Laboratory s (ORNL)more » big area additive manufacturing (BAAM) system, are summarized. In doing so, a survey of tools for designers and software developers is provided. In particular, strategies in which geometric data can be used as training sets for smarter AM technologies in the future are explained as well.« less

DESIGN AND CALIBRATION OF THE EPA PM2.5 WELL IMPACTOR NINETY-SIX (WINS)

EPA Science Inventory

The EPA well-type impactor ninety-six (WINS) was designed and calibrated to serve as a particle size separation device for the EPA reference method sampler for particulate matter under 2.5 um aerodynamic diameter. The WINS was designed to operate downstream of a PM10 inlet at a v...

Student Involvement in Wellness Policies: A Study of Pennsylvania Local Education Agencies

ERIC Educational Resources Information Center

Jomaa, Lamis H.; McDonnell, Elaine; Weirich, Elaine; Hartman, Terryl; Jensen, Leif; Probart, Claudia

2010-01-01

Objective: Explore student-involvement goals in local wellness policies (LWPs) of local education agencies (LEAs) in Pennsylvania (PA) and investigate associations with LEA characteristics. Design: An observational study that helped examine student-involvement goals. Setting: Public PA LEAs. Participants: LWPs submitted by 539 PA public LEAs. Main…

Design of a Drug-in-Adhesive Transdermal Patch for Risperidone: Effect of Drug-Additive Interactions on the Crystallization Inhibition and In Vitro/In Vivo Correlation Study.

PubMed

Weng, Wei; Quan, Peng; Liu, Chao; Zhao, Hanqing; Fang, Liang

2016-10-01

The purpose of this work was to develop and design an appropriate drug-in-adhesive patch for transdermal delivery of risperidone (RISP). Various formulation factors were investigated by in vitro permeation study using excised rabbit skin. Increasing the drug concentration in the pressure sensitive adhesive (PSA) was used to enhance the drug permeation. To overcome the high crystallization tendency of the patch, several crystallization inhibitors such as PVP, PEG, and surfactants and fatty acids were evaluated by microscopy study. The mechanism of crystallization inhibition was investigated by differential scanning calorimetry, nuclear magnetic resonance spectrometer, and FT-IR studies. RISP and its active metabolite were determined after topical application of the optimized transdermal patch, and the in vivo pharmacokinetic parameters were compared with the intravenous administration group. The microscopy study indicated that fatty acid greatly inhibited the crystallization of RISP in PSA. The inhibition was attributed to the drug-additive interaction between amino group of RISP and the carboxyl group of fatty acid which was further confirmed by (1)H-NMR and FT-IR studies. The optimal permeation profile was obtained with the patches containing 5% RISP and 5% oleic acid in Duro-Tak(®) 87-2287. The in vivo pharmacokinetic study exhibited a sustained absorption and metabolism profile and well correlated with the in vitro permeation data. Copyright © 2016 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Additive Manufacturing: Unlocking the Evolution of Energy Materials

PubMed Central

Zhakeyev, Adilet; Wang, Panfeng; Shu, Wenmiao; Wang, Huizhi

2017-01-01

Abstract The global energy infrastructure is undergoing a drastic transformation towards renewable energy, posing huge challenges on the energy materials research, development and manufacturing. Additive manufacturing has shown its promise to change the way how future energy system can be designed and delivered. It offers capability in manufacturing complex 3D structures, with near‐complete design freedom and high sustainability due to minimal use of materials and toxic chemicals. Recent literatures have reported that additive manufacturing could unlock the evolution of energy materials and chemistries with unprecedented performance in the way that could never be achieved by conventional manufacturing techniques. This comprehensive review will fill the gap in communicating on recent breakthroughs in additive manufacturing for energy material and device applications. It will underpin the discoveries on what 3D functional energy structures can be created without design constraints, which bespoke energy materials could be additively manufactured with customised solutions, and how the additively manufactured devices could be integrated into energy systems. This review will also highlight emerging and important applications in energy additive manufacturing, including fuel cells, batteries, hydrogen, solar cell as well as carbon capture and storage. PMID:29051861

Additive Manufacturing: Unlocking the Evolution of Energy Materials.

PubMed

Zhakeyev, Adilet; Wang, Panfeng; Zhang, Li; Shu, Wenmiao; Wang, Huizhi; Xuan, Jin

2017-10-01

The global energy infrastructure is undergoing a drastic transformation towards renewable energy, posing huge challenges on the energy materials research, development and manufacturing. Additive manufacturing has shown its promise to change the way how future energy system can be designed and delivered. It offers capability in manufacturing complex 3D structures, with near-complete design freedom and high sustainability due to minimal use of materials and toxic chemicals. Recent literatures have reported that additive manufacturing could unlock the evolution of energy materials and chemistries with unprecedented performance in the way that could never be achieved by conventional manufacturing techniques. This comprehensive review will fill the gap in communicating on recent breakthroughs in additive manufacturing for energy material and device applications. It will underpin the discoveries on what 3D functional energy structures can be created without design constraints, which bespoke energy materials could be additively manufactured with customised solutions, and how the additively manufactured devices could be integrated into energy systems. This review will also highlight emerging and important applications in energy additive manufacturing, including fuel cells, batteries, hydrogen, solar cell as well as carbon capture and storage.

Medication safety research by observational study design.

PubMed

Lao, Kim S J; Chui, Celine S L; Man, Kenneth K C; Lau, Wallis C Y; Chan, Esther W; Wong, Ian C K

2016-06-01

Observational studies have been recognised to be essential for investigating the safety profile of medications. Numerous observational studies have been conducted on the platform of large population databases, which provide adequate sample size and follow-up length to detect infrequent and/or delayed clinical outcomes. Cohort and case-control are well-accepted traditional methodologies for hypothesis testing, while within-individual study designs are developing and evolving, addressing previous known methodological limitations to reduce confounding and bias. Respective examples of observational studies of different study designs using medical databases are shown. Methodology characteristics, study assumptions, strengths and weaknesses of each method are discussed in this review.

Study Designs and Statistical Analyses for Biomarker Research

PubMed Central

Gosho, Masahiko; Nagashima, Kengo; Sato, Yasunori

2012-01-01

Biomarkers are becoming increasingly important for streamlining drug discovery and development. In addition, biomarkers are widely expected to be used as a tool for disease diagnosis, personalized medication, and surrogate endpoints in clinical research. In this paper, we highlight several important aspects related to study design and statistical analysis for clinical research incorporating biomarkers. We describe the typical and current study designs for exploring, detecting, and utilizing biomarkers. Furthermore, we introduce statistical issues such as confounding and multiplicity for statistical tests in biomarker research. PMID:23012528

[The case-case-time-control study design].

PubMed

Wang, Jing; Zhuo, Lin; Zhan, Siyan

2014-12-01

Although the 'self-matched case-only studies' (such as the case-cross-over or self-controlled case-series method) can control the time-invariant confounders (measured or unmeasured) through design of the study, however, they can not control those confounders that vary with time. A bidirectional case-crossover design can be used to adjust the exposure-time trends. In the areas of pharmaco-epidemiology, illness often influence the future use of medications, making a bidirectional study design problematic. Suissa's case-time-control design combines the case-crossover and the case-control design which could adjust for exposure-trend bias, but the control group may reintroduce selection bias, if the matching does not go well. We propose a "case-case-time-control" design which is an extension of the case-time-control design. However, rather than using a sample of external controls, we choose those future cases as controls for current cases to counter the bias that arising from temporal trends caused by exposure to the target of interest. In the end of this article we will discuss the strength and limitations of this design based on an applied example.

77 FR 58911 - Additional Identifying Information for One (1) Individual Designated Pursuant to Executive Order...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-24

... Designated Nationals and Blocked Persons (``SDN List'') on September 13, 2012. FOR FURTHER INFORMATION... and Facsimile Availability The SDN List and additional information concerning OFAC are available from...

78 FR 77686 - Designation of a Class of Employees for Addition to the Special Exposure Cohort

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-24

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Designation of a Class of Employees for Addition to the... Disease Control and Prevention, Department of Health and Human Services (HHS). ACTION: Notice. SUMMARY: HHS gives notice of a decision to designate a class of employees from the Rocky Flats Plant in Golden...

78 FR 64501 - Designation of a Class of Employees for Addition to the Special Exposure Cohort

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-29

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Designation of a Class of Employees for Addition to the... Disease Control and Prevention, Department of Health and Human Services (HHS). ACTION: Notice. SUMMARY: HHS gives notice of a decision to designate a class of employees from the Pantex Plant in Amarillo...

77 FR 76489 - Designation of a Class of Employees for Addition to the Special Exposure Cohort

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-28

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Designation of a Class of Employees for Addition to the... Disease Control and Prevention, Department of Health and Human Services (HHS). ACTION: Notice. SUMMARY: HHS gives notice of a decision to designate a class of employees from the Mound Plant in Miamisburg...

Unique Study Designs in Nephrology: N-of-1 Trials and Other Designs.

PubMed

Samuel, Joyce P; Bell, Cynthia S

2016-11-01

Alternatives to the traditional parallel-group trial design may be required to answer clinical questions in special populations, rare conditions, or with limited resources. N-of-1 trials are a unique trial design which can inform personalized evidence-based decisions for the patient when data from traditional clinical trials are lacking or not generalizable. A concise overview of factorial design, cluster randomization, adaptive designs, crossover studies, and n-of-1 trials will be provided along with pertinent examples in nephrology. The indication for analysis strategies such as equivalence and noninferiority trials will be discussed, as well as analytic pitfalls. Copyright © 2016 National Kidney Foundation, Inc. Published by Elsevier Inc. All rights reserved.

Cloud-Based Automated Design and Additive Manufacturing: A Usage Data-Enabled Paradigm Shift

PubMed Central

Lehmhus, Dirk; Wuest, Thorsten; Wellsandt, Stefan; Bosse, Stefan; Kaihara, Toshiya; Thoben, Klaus-Dieter; Busse, Matthias

2015-01-01

Integration of sensors into various kinds of products and machines provides access to in-depth usage information as basis for product optimization. Presently, this large potential for more user-friendly and efficient products is not being realized because (a) sensor integration and thus usage information is not available on a large scale and (b) product optimization requires considerable efforts in terms of manpower and adaptation of production equipment. However, with the advent of cloud-based services and highly flexible additive manufacturing techniques, these obstacles are currently crumbling away at rapid pace. The present study explores the state of the art in gathering and evaluating product usage and life cycle data, additive manufacturing and sensor integration, automated design and cloud-based services in manufacturing. By joining and extrapolating development trends in these areas, it delimits the foundations of a manufacturing concept that will allow continuous and economically viable product optimization on a general, user group or individual user level. This projection is checked against three different application scenarios, each of which stresses different aspects of the underlying holistic concept. The following discussion identifies critical issues and research needs by adopting the relevant stakeholder perspectives. PMID:26703606

Cloud-Based Automated Design and Additive Manufacturing: A Usage Data-Enabled Paradigm Shift.

PubMed

Lehmhus, Dirk; Wuest, Thorsten; Wellsandt, Stefan; Bosse, Stefan; Kaihara, Toshiya; Thoben, Klaus-Dieter; Busse, Matthias

2015-12-19

Integration of sensors into various kinds of products and machines provides access to in-depth usage information as basis for product optimization. Presently, this large potential for more user-friendly and efficient products is not being realized because (a) sensor integration and thus usage information is not available on a large scale and (b) product optimization requires considerable efforts in terms of manpower and adaptation of production equipment. However, with the advent of cloud-based services and highly flexible additive manufacturing techniques, these obstacles are currently crumbling away at rapid pace. The present study explores the state of the art in gathering and evaluating product usage and life cycle data, additive manufacturing and sensor integration, automated design and cloud-based services in manufacturing. By joining and extrapolating development trends in these areas, it delimits the foundations of a manufacturing concept that will allow continuous and economically viable product optimization on a general, user group or individual user level. This projection is checked against three different application scenarios, each of which stresses different aspects of the underlying holistic concept. The following discussion identifies critical issues and research needs by adopting the relevant stakeholder perspectives.

Characterization and optimization of slanted well designs for microfluidic mixing under electroosmotic flow.

PubMed

Johnson, Timothy J; Locascio, Laurie E

2002-08-01

Recently, a series of slanted wells on the floor of a microfluidic channel were experimentally shown to successfully induce off-axis transport and mixing of two confluent streams when operating under electroosmotic (EO) flow. This paper will further explore, through numerical simulations, the parameters that affect off-axis transport under EO flow with an emphasis on optimizing the mixing rate of (a). two confluent streams in steady-state or (b). the transient scenario of two confluent plugs of material, which simulates mixing after an injection. For the steady-state scenario, the degree of mixing was determined to increase by changing any of the following parameters: (1). increasing the well depth, (2). decreasing the well angle relative to the axis of the channel, and (3). increasing the EO mobility of the well walls relative to the mobility of the main channel. Also, it will be shown that folding of the fluid can occur when the well angle is sufficiently reduced and/or when the EO mobility of the wells is increased relative to the channel. The optimum configuration for the transient problem of mixing two confluent plugs includes shallow wells to minimize the well residence time, and an increased EO mobility of the well walls relative to the main channel as well as small well angles to maximize off-axis transport. The final design reported here for the transient study reduces the standard deviation of the concentration across the channel by 72% while only increasing the axial dispersion of the injected plug by 8.6 % when compared to a plug injected into a channel with no wells present. These results indicate that a series of slanted wells on the wall of a microchannel provides a means for controlling and achieving a high degree of off-axis transport and mixing in a passive manner for micro total analysis system (microTAS) devices that are driven by electroosmosis.

Design of microarray experiments for genetical genomics studies.

PubMed

Bueno Filho, Júlio S S; Gilmour, Steven G; Rosa, Guilherme J M

2006-10-01

Microarray experiments have been used recently in genetical genomics studies, as an additional tool to understand the genetic mechanisms governing variation in complex traits, such as for estimating heritabilities of mRNA transcript abundances, for mapping expression quantitative trait loci, and for inferring regulatory networks controlling gene expression. Several articles on the design of microarray experiments discuss situations in which treatment effects are assumed fixed and without any structure. In the case of two-color microarray platforms, several authors have studied reference and circular designs. Here, we discuss the optimal design of microarray experiments whose goals refer to specific genetic questions. Some examples are used to illustrate the choice of a design for comparing fixed, structured treatments, such as genotypic groups. Experiments targeting single genes or chromosomic regions (such as with transgene research) or multiple epistatic loci (such as within a selective phenotyping context) are discussed. In addition, microarray experiments in which treatments refer to families or to subjects (within family structures or complex pedigrees) are presented. In these cases treatments are more appropriately considered to be random effects, with specific covariance structures, in which the genetic goals relate to the estimation of genetic variances and the heritability of transcriptional abundances.

Preliminary design study of a baseline MIUS

NASA Technical Reports Server (NTRS)

Wolfer, B. M.; Shields, V. E.; Rippey, J. O.; Roberts, H. L.; Wadle, R. C.; Wallin, S. P.; Gill, W. L.; White, E. H.; Monzingo, R.

1977-01-01

Results of a conceptual design study to establish a baseline design for a modular integrated utility system (MIUS) are presented. The system concept developed a basis for evaluating possible projects to demonstrate an MIUS. For the baseline study, climate conditions for the Washington, D.C., area were used. The baseline design is for a high density apartment complex of 496 dwelling units with a planned full occupancy of approximately 1200 residents. Environmental considerations and regulations for the MIUS installation are discussed. Detailed cost data for the baseline MIUS are given together with those for design and operating variations under climate conditions typified by Las Vegas, Nevada, Houston, Texas, and Minneapolis, Minnesota. In addition, results of an investigation of size variation effects, for 300 and 1000 unit apartment complexes, are presented. Only conceptual aspects of the design are discussed. Results regarding energy savings and costs are intended only as trend information and for use in relative comparisons. Alternate heating, ventilation, and air conditioning concepts are considered in the appendix.

A study of hydrocarbons associated with brines from DOE geopressured wells. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Keeley, D.F.

1993-07-01

Accomplishments are summarized on the following tasks: distribution coefficients and solubilities, DOE design well sampling, analysis of well samples, review of theoretical models of geopressured reservoir hydrocarbons, monitor for aliphatic hydrocarbons, development of a ph meter probe, DOE design well scrubber analysis, removal and disposition of gas scrubber equipment at Pleasant Bayou Well, and disposition of archived brines.

The Crucial Role of Additive Manufacturing at NASA

NASA Technical Reports Server (NTRS)

Vickers, John

2016-01-01

At NASA, the first steps of the Journey to Mars are well underway with the development of NASA's next generation launch system and investments in research and technologies that should increase the affordability, capability, and safety of exploration activities. Additive Manufacturing presents a disruptive opportunity for NASA to design and manufacture hardware with new materials at dramatically reduced cost and schedule. Opportunities to incorporate additive manufacturing align very well with NASA missions and with most NASA programs related to space, science, and aeronautics. The Agency also relies on many partnerships with other government agencies, industry and academia.

Sand-control completion design, installation, and performance in high-rate gas wells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burton, R.C.; Boggan, S.A.

1998-09-01

The Jupiter fields consist of a number of separate Rotliegendes gas reservoirs located approximately 90 miles off the Lincolnshire coast of the UK. The fields that make up Jupiter are Ganymede, Calisto, Europa, Sinope, and Thebe. Originally discovered in 1970, initial appraisal wells indicated poor reservoir properties and low deliverabilities. Development was postponed until a reappraisal of the area in the 1990`s indicated significant upside potential. The initial phase of the Jupiter development plan called for development of Ganymede and Calisto fields, with subsequent phases tying in Europa and Thebe. Initial development planning indicated a need for high field deliverabilitymore » at low capital cost to meet economic targets. A small number of high-rate-potential wells were to be used to deplete the reservoir. Ganymede would be developed by use of a 10-slot platform and Calisto would be developed subsea and tied back to the Ganymede platform. The paper discusses the reservoir, formation assessment, productivity design, drilling design, screen installation, and completion performance.« less

The 2016 HIGh Heels: Health effects And psychosexual BenefITS (HIGH HABITS) study: systematic review of reviews and additional primary studies.

PubMed

Barnish, Max; Morgan, Heather May; Barnish, Jean

2017-08-01

High-heeled shoes (high heels) are frequently worn by many women and form an important part of female gender identity. Issues of explicit and implicit compulsion to wear high heels have been noted. Previous studies and reviews have provided evidence that high heels are detrimental to health. However, the evidence base remains fragmented and no review has covered both the epidemiological and biomechanical literature. In addition, no review has considered the psychosexual benefits that offer essential context in understanding the public health challenge of high heels. We searched seven major bibliographic databases up to November 2016, in addition to supplementary searches. We initially identified all review articles of any design that assessed either the psychosexual benefits or negative musculoskeletal health effects of high heels, the latter looking at both the epidemiological and biomechanical perspectives. We additionally considered additional primary studies on areas that had not been reviewed before or in which a marked lack of evidence had been noted. Data were extracted onto standardised forms. Proportionate second review was conducted. A total of 506 unique records were identified, 27 full-text publications were screened and 20 publications (7 reviews and 13 additional studies) were included in our evidence synthesis. The most up-to-date epidemiological review provides clear evidence of an association between high heel wear and hallux valgus, musculoskeletal pain and first-party injury. The body of biomechanical reviews provides clear evidence of changes indicative of increased risk of these outcomes, as well as osteoarthritis, which is not yet evidenced by epidemiological studies. There were no reviews on psychosexual benefits, but all five identified original studies provided evidence of increased attractiveness and/or an impact on men's behaviour associated with high heel wear. With regard to second-party injury, evidence is limited to one descriptive

Exploring self-compassion and eudaimonic well-being in young women athletes.

PubMed

Ferguson, Leah J; Kowalski, Kent C; Mack, Diane E; Sabiston, Catherine M

2014-04-01

Using a mixed methods research design, we explored self-compassion and eudaimonic well-being in young women athletes. In a quantitative study (n = 83), we found that self-compassion and eudaimonic well-being were positively related (r = .76, p < .01). A model of multiple mediation was proposed, with self-compassion, passivity, responsibility, initiative, and self-determination accounting for 83% of the variance in eudaimonic well-being. In a qualitative study (n = 11), we explored when and how self-compassion might be useful in striving to reach one's potential in sport. Self-compassion was described as advantageous in difficult sport-specific situations by increasing positivity, perseverance, and responsibility, as well as decreasing rumination. Apprehensions about fully embracing a self-compassionate mindset in sport warrant additional research to explore the seemingly paradoxical role of self-compassion in eudaimonic well-being.

Microstructural Development and Technical Challenges in Laser Additive Manufacturing: Case Study with a 316L Industrial Part

NASA Astrophysics Data System (ADS)

Marya, Manuel; Singh, Virendra; Marya, Surendar; Hascoet, Jean Yves

2015-08-01

Additive manufacturing (AM) brings disruptive changes to the ways parts, and products are designed, fabricated, tested, qualified, inspected, marketed, and sold. These changes introduce novel technical challenges and concerns arising from the maturity and diversity of today's AM processes, feedstock materials, and process parameter interactions. AM bears a resemblance with laser and electron beam welding in the so-called conduction mode, which involves a multitude of dynamic physical events between the projected feedstock and a moving heat source that eventually influence AM part properties. For this paper, an air vent was selected for its thin-walled, hollow, and variable cross section, and limited size. The studied air vents, randomly selected from a qualification batch, were fabricated out of 316L stainless steel using a 4 kW fiber laser powder-fed AM system, referred to as construction laser additive direct (CLAD). These were systematically characterized by microhardness indentation, visual examination, optical and scanning electron microscopy, and electron-back-scattering diffraction in order to determine AM part suitability for service and also broadly discuss metallurgical phenomena. The paper then briefly expands the discussion to include additional engineering alloys and further analyze relationships between AM process parameters and AM part properties, consistently utilizing past experience with the same powder-fed CLAD 3D printer, the well-established science and technology of welding and joining, and recent publications on additive manufacturing.

Well-Designed Bone-Seeking Radiolabeled Compounds for Diagnosis and Therapy of Bone Metastases

PubMed Central

2015-01-01

Bone-seeking radiopharmaceuticals are frequently used as diagnostic agents in nuclear medicine, because they can detect bone disorders before anatomical changes occur. Furthermore, their effectiveness in the palliation of metastatic bone cancer pain has been demonstrated in the clinical setting. With the aim of developing superior bone-seeking radiopharmaceuticals, many compounds have been designed, prepared, and evaluated. Here, several well-designed bone-seeking compounds used for diagnostic and therapeutic use, having the concept of radiometal complexes conjugated to carrier molecules to bone, are reviewed. PMID:26075256

Designing Web-Based Educative Curriculum Materials for the Social Studies

ERIC Educational Resources Information Center

Callahan, Cory; Saye, John; Brush, Thomas

2013-01-01

This paper reports on a design experiment of web-based curriculum materials explicitly created to help social studies teachers develop their professional teaching knowledge. Web-based social studies curriculum reform efforts, human-centered interface design, and investigations into educative curriculum materials are reviewed, as well as…

Additive Manufacturing, Design, Testing, and Fabrication: A Full Engineering Experience at JSC

NASA Technical Reports Server (NTRS)

Zusack, Steven

2016-01-01

I worked on several projects this term. While most projects involved additive manufacturing, I was also involved with two design projects, two testing projects, and a fabrication project. The primary mentor for these was Richard Hagen. Secondary mentors were Hai Nguyen, Khadijah Shariff, and fabrication training from James Brown. Overall, my experience at JSC has been successful and what I have learned will continue to help me in my engineering education and profession long after I leave. My 3D printing projects ranged from less than a 1 cubic centimeter to about 1 cubic foot and involved several printers using different printing technologies. It was exciting to become familiar with printing technologies such as industrial grade FDM (Fused Deposition Modeling), the relatively new SLA (Stereolithography), and PolyJet. My primary duty with the FDM printers was to model parts that came in from various sources to print effectively and efficiently. Using methods my mentor taught me and the Stratasys Insight software, I was able to minimize imperfections, hasten build time, improve strength for specific forces (tensile, shear, etc...), and reduce likelihood of a print-failure. Also using FDM, I learned how to repair a part after it was printed. This is done by using a special kind of glue that chemically melts the two faces of plastic parts together to form a fused interface. My first goal with SLA technology was to bring the printer back to operational readiness. In becoming familiar with the Pegasus SLA printer, I researched the leveling, laser settings, and different vats to hold liquid material. With this research, I was successfully able to bring the Pegasus back online and have successfully printed multiple sample parts as well as functional parts. My experience with PolyJet technology has been focused on an understanding of the abilities/limits, costs, and the maintenance for daily use. Still upcoming will be experience with using a composite printer that uses FDM

Multiport well design for sampling of ground water at closely spaced vertical intervals

USGS Publications Warehouse

Delin, G.N.; Landon, M.K.

1996-01-01

Detailed vertical sampling is useful in aquifers where vertical mixing is limited and steep vertical gradients in chemical concentrations are expected. Samples can be collected at closely spaced vertical intervals from nested wells with short screened intervals. However, this approach may not be appropriate in all situations. An easy-to-construct and easy-to-install multiport sampling well to collect ground-water samples from closely spaced vertical intervals was developed and tested. The multiport sampling well was designed to sample ground water from surficial sand-and-gravel aquifers. The device consists of multiple stainless-steel tubes within a polyvinyl chloride (PVC) protective casing. The tubes protrude through the wall of the PVC casing at the desired sampling depths. A peristaltic pump is used to collect ground-water samples from the sampling ports. The difference in hydraulic head between any two sampling ports can be measured with a vacuum pump and a modified manometer. The usefulness and versatility of this multiport well design was demonstrated at an agricultural research site near Princeton, Minnesota where sampling ports were installed to a maximum depth of about 12 m below land surface. Tracer experiments were conducted using potassium bromide to document the degree to which short-circuiting occurred between sampling ports. Samples were successfully collected for analysis of major cations and anions, nutrients, selected herbicides, isotopes, dissolved gases, and chlorofluorcarbon concentrations.

Wellness partners: design and evaluation of a web-based physical activity diary with social gaming features for adults.

PubMed

Gotsis, Marientina; Wang, Hua; Spruijt-Metz, Donna; Jordan-Marsh, Maryalice; Valente, Thomas William

2013-02-01

The United States is currently in an age of obesity and inactivity despite increasing public awareness and scientific knowledge of detrimental long-term health effects of this lifestyle. Behavior-tracking diaries offer an effective strategy for physical activity adherence and weight management. Furthermore, Web-based physical activity diaries can engage meaningful partners in people's social networks through fun online gaming interactions and generate motivational mechanisms for effective behavioral change and positive health outcomes. Wellness Partners (WP) is a Web-based intervention in the form of a physical activity diary with social networking and game features. Two versions were designed and developed for the purpose of this study-"Diary" only and "Diary+Game". The objectives of this study included pilot testing the research process of this intervention design, implementation, evaluation, and exploring the effectiveness of social gaming features on adult participants' physical activity and anthropometric measures. We conducted a field experiment with randomized crossover design. Assessments occurred at baseline, first follow-up (FU, 5-8 weeks after using one version of WP), and second FU (5-8 weeks of using the other version of WP). In the control condition, participants started with the "Diary" version of WP while in the experimental condition, participants started with the "Diary+Game" version of WP. A total of 54 adults (egos) ages 44-88, and their family and friends (alters) ages 17-69 participated in the study in ego-network groups. Both egos and their alters completed online surveys about their exercise habits. In addition, egos completed anthropometric measurements of BMI, fat percentage, and fat mass by bioimpedance. From October 2009 to May 2010, flyers, emails, and Web advertisements yielded 335 volunteers who were screened. Rolling recruitment resulted in enrollment of 142 qualified participants in 54 ego-network groups, which were randomly

A Case Study of Educational Computer Game Design by Middle School Students

ERIC Educational Resources Information Center

An, Yun-Jo

2016-01-01

Only a limited number of research studies have investigated how students design educational computer games and its impact on student learning. In addition, most studies on educational game design by students were conducted in the areas of mathematics and science. Using the qualitative case study approach, this study explored how seventh graders…

An analytical study for the design of advanced rotor airfoils

NASA Technical Reports Server (NTRS)

Kemp, L. D.

1973-01-01

A theoretical study has been conducted to design and evaluate two airfoils for helicopter rotors. The best basic shape, designed with a transonic hodograph design method, was modified to meet subsonic criteria. One airfoil had an additional constraint for low pitching-moment at the transonic design point. Airfoil characteristics were predicted. Results of a comparative analysis of helicopter performance indicate that the new airfoils will produce reduced rotor power requirements compared to the NACA 0012. The hodograph design method, written in CDC Algol, is listed and described.

Implementing a method of screening one-well hydraulic barrier design alternatives.

PubMed

Rubin, Hillel; Shoemaker, Christine A; Köngeter, Jürgen

2009-01-01

This article provides details of applying the method developed by the authors (Rubin et al. 2008b) for screening one-well hydraulic barrier design alternatives. The present article with its supporting information (manual and electronic spreadsheets with a case history example) provides the reader complete details and examples of solving the set of nonlinear equations developed by Rubin et al. (2008b). It allows proper use of the analytical solutions and also depicting the various charts given by Rubin et al. (2008b). The final outputs of the calculations are the required position and the discharge of the pumping well. If the contaminant source is nonaqueous phase liquid (NAPL) entrapped within the aquifer, then the method provides an estimate of the aquifer remediation progress (which is a by-product) due to operating the hydraulic barrier.

AFE ion mass spectrometer design study

NASA Technical Reports Server (NTRS)

Wright, Willie

1989-01-01

This final technical report covers the activities engaged in by the University of Texas at Dallas, Center for Space Sciences in conjunction with the NASA Langley Research Center, Systems Engineering Division in design studies directed towards defining a suitable ion mass spectrometer to determine the plasma parameter around the Aeroassisted Flight Experiment vehicle during passage through the earth's upper atmosphere. Additional studies relate to the use of a Langmuir probe to measure windward ion/electron concentrations and temperatures. Selected instrument inlet subsystems were tested in the NASA Ames Arc-Jet Facility.

Design and fabrication of resonator-quantum well infrared photodetector for SF6 gas sensor application

NASA Astrophysics Data System (ADS)

Sun, Jason; Choi, Kwong-Kit; DeCuir, Eric; Olver, Kimberley; Fu, Richard

2017-07-01

The infrared absorption of SF6 gas is narrowband and peaks at 10.6 μm. This narrowband absorption posts a stringent requirement on the corresponding sensors as they need to collect enough signal from this limited spectral bandwidth to maintain a high sensitivity. Resonator-quantum well infrared photodetectors (R-QWIPs) are the next generation of QWIP detectors that use resonances to increase the quantum efficiency for more efficient signal collection. Since the resonant approach is applicable to narrowband as well as broadband, it is particularly suitable for this application. We designed and fabricated R-QWIPs for SF6 gas detection. To achieve the expected performance, the detector geometry must be produced according to precise specifications. In particular, the height of the diffractive elements and the thickness of the active resonator must be uniform, and accurately realized to within 0.05 μm. Additionally, the substrates of the detectors must be completely removed to prevent the escape of unabsorbed light in the detectors. To achieve these specifications, two optimized inductively coupled plasma etching processes were developed. Due to submicron detector feature sizes and overlay tolerance, we used an advanced semiconductor material lithography stepper instead of a contact mask aligner to pattern wafers. Using these etching techniques and tool, we have fabricated focal plane arrays with 30-μm pixel pitch and 320×256 format. The initial test revealed promising results.

Targeted Structural Optimization with Additive Manufacturing of Metals

NASA Technical Reports Server (NTRS)

Burt, Adam; Hull, Patrick

2015-01-01

The recent advances in additive manufacturing (AM) of metals have now improved the state-of-the-art such that traditionally non-producible parts can be readily produced in a cost-effective way. Because of these advances in manufacturing technology, structural optimization techniques are well positioned to supplement and advance this new technology. The goal of this project is to develop a structural design, analysis, and optimization framework combined with AM to significantly light-weight the interior of metallic structures while maintaining the selected structural properties of the original solid. This is a new state-of-the-art capability to significantly reduce mass, while maintaining the structural integrity of the original design, something that can only be done with AM. In addition, this framework will couple the design, analysis, and fabrication process, meaning that what has been designed directly represents the produced part, thus closing the loop on the design cycle and removing human iteration between design and fabrication. This fundamental concept has applications from light-weighting launch vehicle components to in situ resource fabrication.

The Wellness Factor: Embedding Wellness in the Curriculum at Ashley Hall

ERIC Educational Resources Information Center

Murrell, Amanda; Wood, Kelly

2013-01-01

The authors of this article describe the Personal Awareness and Wellness Seminar (PAWS) program, which they developed at Ashley Hall (South Carolina), an all-girls K-12 school. PAWS is designed to incorporate three main areas of school and personal life: academic management and study skills, general wellness and life skills, and the college search…

Optimum study designs.

PubMed

Gu, C; Rao, D C

2001-01-01

Because simplistic designs will lead to prohibitively large sample sizes, the optimization of genetic study designs is critical for successfully mapping genes for complex diseases. Creative designs are necessary for detecting and amplifying the usually weak signals for complex traits. Two important outcomes of a study design--power and resolution--are implicitly tied together by the principle of uncertainty. Overemphasis on either one may lead to suboptimal designs. To achieve optimality for a particular study, therefore, practical measures such as cost-effectiveness must be used to strike a balance between power and resolution. In this light, the myriad of factors involved in study design can be checked for their effects on the ultimate outcomes, and the popular existing designs can be sorted into building blocks that may be useful for particular situations. It is hoped that imaginative construction of novel designs using such building blocks will lead to enhanced efficiency in finding genes for complex human traits.

Peripheral Design of Progressive Addition Lenses and the Lag of Accommodation in Myopes.

PubMed

Schilling, Tim; Ohlendorf, Arne; Varnas, Saulius R; Wahl, Siegfried

2017-07-01

Insufficient accommodative response is assumed to result in myopia progression. We have investigated if the accommodative lag in myopes is different between a single vision lens (SVL) and the progressive addition lens PAL 2, clinically trialled for its ability to reduce progression of myopia, and if there exist differences in accommodative lag between PAL 2 and other PALs with the same addition power (+1.50 D). The influence of spherical SVL and four different designs of PALs that differ in the near zone width (PAL 1) or that have different signs and magnitude of horizontal gradients of mean power adjacent to their near vision zones (PAL 3 and PAL 4) on the accommodative response was investigated for different near viewing distances (40, 33, and 25 cm) in 31 subjects, aged 18 to 25 years. The SVL correction resulted in insufficient accommodative response for the near object viewing distances tested. PAL 2 did significantly reduce accommodative lag for all near object distances tested. The PAL design with a more negative horizontal mean power gradient (PAL 4) provided a lower lag of accommodation when compared with PAL 2 at the shortest object distance of 25 cm (P = 0.03) and was able to reduce the lag of accommodation to a level below the depth of focus for the higher near working distances tested. Designs of PAL with more negative horizontal mean power gradients are the most effective in lowering the lag of accommodation in myopes. This could make them good test candidates for myopia control applications.

Laser and electron-beam powder-bed additive manufacturing of metallic implants: A review on processes, materials and designs.

PubMed

Sing, Swee Leong; An, Jia; Yeong, Wai Yee; Wiria, Florencia Edith

2016-03-01

Additive manufacturing (AM), also commonly known as 3D printing, allows the direct fabrication of functional parts with complex shapes from digital models. In this review, the current progress of two AM processes suitable for metallic orthopaedic implant applications, namely selective laser melting (SLM) and electron beam melting (EBM) are presented. Several critical design factors such as the need for data acquisition for patient-specific design, design dependent porosity for osteo-inductive implants, surface topology of the implants and design for reduction of stress-shielding in implants are discussed. Additive manufactured biomaterials such as 316L stainless steel, titanium-6aluminium-4vanadium (Ti6Al4V) and cobalt-chromium (CoCr) are highlighted. Limitations and future potential of such technologies are also explored. © 2015 Orthopaedic Research Society. Published by Wiley Periodicals, Inc.

The Heart of Grinnell: A Community-Wide Rural Health Wellness Initiative: a pilot observational study and a prospective study design.

PubMed

Linden, Todd C; Jackson, Cory; Rutledge, Sheryl; Nath, Chad; Lof, Laura Nelson

2010-01-01

In 2007, the leadership team at Grinnell Regional Medical Center participated in a pilot project with the Institute of HeartMath (IHM) to assess the stress level of individual team members and its effect on the organization. At the beginning of the project, the leadership team completed a Personal and Organizational Quality Assessment (POQA-R). Results showed that a high percentage of the participants were experiencing fatigue, anxiety, difficulty sleeping, and depression. The leadership team participated in a Transforming Stress workshop and began using IHM techniques to deal with the stresses in their personal and professional lives. A 1-month follow up revealed improvement in six of the 10 categories assessed: fatigue, anxiety, depression, anger management, resentfulness, and stress symptoms. Based on this success, GRMC and IHM initiated The Heart of Grinnell: A Community-Wide Rural Health Wellness Initiative to determine if these results could be replicated on a community level. This project is a health and disease promotion, chronic disease prevention, and education wellness initiative. Located in Grinnell and Poweshiek County, Iowa, this initiative is a multicomponent, community-wide intervention that includes Grinnell College, schools, churches, businesses, social service agencies, local government, and Grinnell Regional Medical Center in partnership with IHM and the University of Iowa College of Public Health. At the center of this project is the goal of training community groups on using a scientifically researched program created by the IHM designed to reduce stress and increase coherence. Coherence implies order, structure, harmony, and alignment among systems-whether in cells and organs, entire organisms, or social groups including communities and counties. The primary objective of The Heart of Grinnell project is to measure the results of a community-wide program to increase community coherence and stress reduction in order to improve adherence to

Rational risk-based decision support for drinking water well managers by optimized monitoring designs

NASA Astrophysics Data System (ADS)

Enzenhöfer, R.; Geiges, A.; Nowak, W.

2011-12-01

Advection-based well-head protection zones are commonly used to manage the contamination risk of drinking water wells. Considering the insufficient knowledge about hazards and transport properties within the catchment, current Water Safety Plans recommend that catchment managers and stakeholders know, control and monitor all possible hazards within the catchments and perform rational risk-based decisions. Our goal is to supply catchment managers with the required probabilistic risk information, and to generate tools that allow for optimal and rational allocation of resources between improved monitoring versus extended safety margins and risk mitigation measures. To support risk managers with the indispensable information, we address the epistemic uncertainty of advective-dispersive solute transport and well vulnerability (Enzenhoefer et al., 2011) within a stochastic simulation framework. Our framework can separate between uncertainty of contaminant location and actual dilution of peak concentrations by resolving heterogeneity with high-resolution Monte-Carlo simulation. To keep computational costs low, we solve the reverse temporal moment transport equation. Only in post-processing, we recover the time-dependent solute breakthrough curves and the deduced well vulnerability criteria from temporal moments by non-linear optimization. Our first step towards optimal risk management is optimal positioning of sampling locations and optimal choice of data types to reduce best the epistemic prediction uncertainty for well-head delineation, using the cross-bred Likelihood Uncertainty Estimator (CLUE, Leube et al., 2011) for optimal sampling design. Better monitoring leads to more reliable and realistic protection zones and thus helps catchment managers to better justify smaller, yet conservative safety margins. In order to allow an optimal choice in sampling strategies, we compare the trade-off in monitoring versus the delineation costs by accounting for ill

Study Of Lampungnese Traditional Home Garden Design

NASA Astrophysics Data System (ADS)

Pratiwi, R. A.; Gunawan

2017-10-01

Lampung is one area in Indonesia which has a traditional culture that comes from two groups of descents, they are ulun Lampung Pepadun and ulun Lampung Saibatin. Lampungnese traditional culture has been well-known by Indonesian people for its traditional dances, traditional clothing, or traditional home architecture. However, Lampungnese traditional home garden recently may not yet been described. Information related to Lampungnese traditional home garden is still very limited and it does not yet represented the culture based design concept. This research was directed to identify the elements of the home garden and map it into design concept of the Lampungnese traditional home garden based on information of Lampungnese traditional culture. The study was conducted by using descriptive approach through literature review, interviews and cultural exploration, as well as field observation. The study was able to identify the elements forming the Lampungnese traditional home garden, namely gakhang hadap, walai, outdoor kitchenette, firewood place, outdoor kitchen, livestock barns, as well as plants. Space layout of the home garden comprises front yard (tengahbah/terambah/beruan), side yard (kebik/kakebik), and backyard (kudan/juyu/kebon). Each element of the garden is located in the right place of the space layout.

Design of distributed systems of hydrolithospere processes management. Selection of optimal number of extracting wells

NASA Astrophysics Data System (ADS)

Pershin, I. M.; Pervukhin, D. A.; Ilyushin, Y. V.; Afanaseva, O. V.

2017-10-01

The article considers the important issue of designing the distributed systems of hydrolithospere processes management. Control effects on the hydrolithospere processes are implemented by a set of extractive wells. The article shows how to determine the optimal number of extractive wells that provide a distributed control impact on the management object.

Comparative study on stained InGaAs quantum wells for high-speed optical-interconnect VCSELs

NASA Astrophysics Data System (ADS)

Li, Hui; Jia, Xiaowei

2018-05-01

The gain-carrier characteristics of InGaAs quantum well for 980 nm high-speed, energy-efficient vertical-cavity surface-emitting lasers are investigated. We specially studied the potentially InGaAs quantum well designs can be used for the active region of energy-efficient, temperature-stable 980-nm VCSEL, which introduced a quantum well gain peak wavelength-to-cavity resonance wavelength offset to improve the dynamic performance at high operation temperature. Several candidate quantum wells are being compared in theory and measurement. We found that ∼5 nm InGaAs QW with ∼6 nm barrier thickness is suitable for the active region of high-speed optical interconnect 980 nm VCSELs, and no significant improvement in the 20% range of In content of InGaAs QWs. The results are useful for next generation green photonic device design.

Wellness Partners: Design and Evaluation of a Web-Based Physical Activity Diary with Social Gaming Features for Adults

PubMed Central

Wang, Hua; Spruijt-Metz, Donna; Jordan-Marsh, Maryalice; Valente, Thomas William

2013-01-01

Background The United States is currently in an age of obesity and inactivity despite increasing public awareness and scientific knowledge of detrimental long-term health effects of this lifestyle. Behavior-tracking diaries offer an effective strategy for physical activity adherence and weight management. Furthermore, Web-based physical activity diaries can engage meaningful partners in people’s social networks through fun online gaming interactions and generate motivational mechanisms for effective behavioral change and positive health outcomes. Objective Wellness Partners (WP) is a Web-based intervention in the form of a physical activity diary with social networking and game features. Two versions were designed and developed for the purpose of this study—“Diary” only and “Diary+Game”. The objectives of this study included pilot testing the research process of this intervention design, implementation, evaluation, and exploring the effectiveness of social gaming features on adult participants’ physical activity and anthropometric measures. Methods We conducted a field experiment with randomized crossover design. Assessments occurred at baseline, first follow-up (FU, 5-8 weeks after using one version of WP), and second FU (5-8 weeks of using the other version of WP). In the control condition, participants started with the “Diary” version of WP while in the experimental condition, participants started with the “Diary+Game” version of WP. A total of 54 adults (egos) ages 44-88, and their family and friends (alters) ages 17-69 participated in the study in ego-network groups. Both egos and their alters completed online surveys about their exercise habits. In addition, egos completed anthropometric measurements of BMI, fat percentage, and fat mass by bioimpedance. Results From October 2009 to May 2010, flyers, emails, and Web advertisements yielded 335 volunteers who were screened. Rolling recruitment resulted in enrollment of 142 qualified

Assessment of codes, by-laws and regulations relating to air wells in building design

NASA Astrophysics Data System (ADS)

Fadzil, Sharifah Fairuz Syed; Karamazaman, Nazli

2017-10-01

Codes and by-laws concerning air well design (for buildings and lavatories) in Malaysia has been established in the Malaysian Uniform Building By-Laws UBBL number 40 (1) and (2) since the 1980s. Wells are there to fulfill the ventilation and daylighting requirements. The minimum well area according to building storey height are compared between UBBL and the Singapore's well requirements from the Building Construction Authority BCA. A visual and graphical representation (with schematics building and well diagrams drawn to scale) of the minimum well sizes and dimensions is given. It can be seen that if the minimum requirement of well size is used for buildings above 8 storeys high, a thin well resulted which is not proportionate to the building height. A proposed dimension is graphed and given to be used in the UBBL which translated to graphics (3 dimensional buildings drawn to scale) created a much better well proportion.

78 FR 70630 - Additional Designations, Foreign Narcotics Kingpin Designation Act

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-26

... FURTHER INFORMATION CONTACT: Assistant Director, Sanctions Compliance & Evaluation, Office of Foreign..., a person designated pursuant to the Kingpin Act; or (3) playing a significant role in international...

76 FR 6056 - Additional Air Quality Designations for the 2006 24-Hour Fine Particle National Ambient Air...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-03

...-9261-3] RIN 2060-AQ30 Additional Air Quality Designations for the 2006 24-Hour Fine Particle National..., and Decisions Related to the 1997 Air Quality Designations and Classifications for the Annual Fine... nationwide for all but three areas for the 2006 24-hour fine particle (PM 2.5 ) National Ambient Air Quality...

A non-additive repulsive contribution in an equation of state: The development for homonuclear square well chains equation of state validated against Monte Carlo simulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Trinh, Thi-Kim-Hoang; Laboratoire de Science des Procédés et des Matériaux; Passarello, Jean-Philippe, E-mail: Jean-Philippe.Passarello@lspm.cnrs.fr

This work consists of the adaptation of a non-additive hard sphere theory inspired by Malakhov and Volkov [Polym. Sci., Ser. A 49(6), 745–756 (2007)] to a square-well chain. Using the thermodynamic perturbation theory, an additional term is proposed that describes the effect of perturbing the chain of square well spheres by a non-additive parameter. In order to validate this development, NPT Monte Carlo simulations of thermodynamic and structural properties of the non-additive square well for a pure chain and a binary mixture of chains are performed. Good agreements are observed between the compressibility factors originating from the theory and thosemore » from molecular simulations.« less

A hingeless rotor XV-15 design integration feasibility study. Volume 1: Engineering design studies

NASA Technical Reports Server (NTRS)

Magee, J. P.; Alexander, H. R.

1978-01-01

A design integration feasibility study was carried out to investigate what modifications to the basic XV-15 were necessary to accomplish a flight demonstration of the XV-15 with a Boeing hingeless rotor. Also investigated were additional modifications which would exploit the full capability provided by the combination of the new rotor and the existing T53 engine. An evaluation of the aircraft is presented and the data indicate improved air vehicle performance, acceptable aeroelastic margins, lower noise levels and improved flying qualities compared with the XV-15 aircraft. Inspection of the rotor system data provided shows an essentially unlimited life rotor for the flight spectrum anticipated for the XV-15.

A national assessment of underground natural gas storage: identifying wells with designs likely vulnerable to a single-point-of-failure

NASA Astrophysics Data System (ADS)

Michanowicz, Drew R.; Buonocore, Jonathan J.; Rowland, Sebastian T.; Konschnik, Katherine E.; Goho, Shaun A.; Bernstein, Aaron S.

2017-05-01

The leak of processed natural gas (PNG) from October 2015 to February 2016 from the Aliso Canyon storage facility, near Los Angeles, California, was the largest single accidental release of greenhouse gases in US history. The Interagency Task Force on Natural Gas Storage Safety and California regulators recently recommended operators phase out single-point-of-failure (SPF) well designs. Here, we develop a national dataset of UGS well activity in the continental US to assess regulatory data availability and uncertainty, and to assess the prevalence of certain well design deficiencies including single-point-of-failure designs. We identified 14 138 active UGS wells associated with 317 active UGS facilities in 29 states using regulatory and company data. State-level wellbore datasets contained numerous reporting inconsistencies that limited data concatenation. We identified 2715 active UGS wells across 160 facilities that, like the failed well at Aliso Canyon, predated the storage facility, and therefore were not originally designed for gas storage. The majority (88%) of these repurposed wells are located in OH, MI, PA, NY, and WV. Repurposed wells have a median age of 74 years, and the 2694 repurposed wells constructed prior to 1979 are particularly likely to exhibit design-related deficiencies. An estimated 210 active repurposed wells were constructed before 1917—before cement zonal isolation methods were utilized. These wells are located in OH, PA, NY, and WV and represent the highest priority related to potential design deficiencies that could lead to containment loss. This national baseline assessment identifies regulatory data uncertainties, highlights a potentially widespread vulnerability of the natural gas supply chain, and can aid in prioritization and oversight for high-risk wells and facilities.

Invited review: study design considerations for clinical research in veterinary radiology and radiation oncology.

PubMed

Scrivani, Peter V; Erb, Hollis N

2013-01-01

High quality clinical research is essential for advancing knowledge in the areas of veterinary radiology and radiation oncology. Types of clinical research studies may include experimental studies, method-comparison studies, and patient-based studies. Experimental studies explore issues relative to pathophysiology, patient safety, and treatment efficacy. Method-comparison studies evaluate agreement between techniques or between observers. Patient-based studies investigate naturally acquired disease and focus on questions asked in clinical practice that relate to individuals or populations (e.g., risk, accuracy, or prognosis). Careful preplanning and study design are essential in order to achieve valid results. A key point to planning studies is ensuring that the design is tailored to the study objectives. Good design includes a comprehensive literature review, asking suitable questions, selecting the proper sample population, collecting the appropriate data, performing the correct statistical analyses, and drawing conclusions supported by the available evidence. Most study designs are classified by whether they are experimental or observational, longitudinal or cross-sectional, and prospective or retrospective. Additional features (e.g., controlled, randomized, or blinded) may be described that address bias. Two related challenging aspects of study design are defining an important research question and selecting an appropriate sample population. The sample population should represent the target population as much as possible. Furthermore, when comparing groups, it is important that the groups are as alike to each other as possible except for the variables of interest. Medical images are well suited for clinical research because imaging signs are categorical or numerical variables that might be predictors or outcomes of diseases or treatments. © 2013 Veterinary Radiology & Ultrasound.

Study design and percent recoveries of anthropogenic organic compounds with and without the addition of ascorbic acid to preserve water samples containing free chlorine, 2004-06

USGS Publications Warehouse

Valder, Joshua F.; Delzer, Gregory C.; Price, Curtis V.; Sandstrom, Mark W.

2008-01-01

The National Water-Quality Assessment (NAWQA) Program of the U.S. Geological Survey (USGS) began implementing Source Water-Quality Assessments (SWQAs) in 2002 that focus on characterizing the quality of source water and finished water of aquifers and major rivers used by some of the larger community water systems in the United States. As used for SWQA studies, source water is the raw (ambient) water collected at the supply well prior to water treatment (for ground water) or the raw (ambient) water collected from the river near the intake (for surface water). Finished water is the water that is treated, which typically involves, in part, the addition of chlorine or other disinfection chemicals to remove pathogens, and is ready to be delivered to consumers. Finished water is collected before the water enters the distribution system. This report describes the study design and percent recoveries of anthropogenic organic compounds (AOCs) with and without the addition of ascorbic acid to preserve water samples containing free chlorine. The percent recoveries were determined by using analytical results from a laboratory study conducted in 2004 by the USGS's National Water Quality Laboratory (NWQL) and from data collected during 2004-06 for a field study currently (2008) being conducted by the USGS's NAWQA Program. The laboratory study was designed to determine if preserving samples with ascorbic acid (quenching samples) adversely affects analytical performance under controlled conditions. During the laboratory study, eight samples of reagent water were spiked for each of five analytical schedules evaluated. Percent recoveries from these samples were then compared in two ways: (1) four quenched reagent spiked samples analyzed on day 0 were compared with four quenched reagent spiked samples analyzed on day 7 or 14, and (2) the combined eight quenched reagent spiked samples analyzed on day 0, 7, or 14 were compared with eight laboratory reagent spikes (LRSs). Percent

Design of the DISCovery project: tailored work-oriented interventions to improve employee health, well-being, and performance-related outcomes in hospital care.

PubMed

Niks, Irene M W; de Jonge, Jan; Gevers, Josette M P; Houtman, Irene L D

2013-02-19

It is well-known that health care workers in today's general hospitals have to deal with high levels of job demands, which could have negative effects on their health, well-being, and job performance. A way to reduce job-related stress reactions and to optimize positive work-related outcomes is to raise the level of specific job resources and opportunities to recover from work. However, the question remains how to translate the optimization of the balance between job demands, job resources, and recovery opportunities into effective workplace interventions. The aim of the DISCovery project is to develop and implement tailored work-oriented interventions to improve health, well-being, and performance of health care personnel. A quasi-experimental field study with a non-equivalent control group pretest-posttest design will be conducted in a top general hospital. Four existing organizational departments will provide both an intervention and a comparison group. Two types of research methods are used: (1) a longitudinal web-based survey study, and (2) a longitudinal daily diary study. After base-line measures of both methods, existing and yet to be developed interventions will be implemented within the experimental groups. Follow-up measurements will be taken one and two years after the base-line measures to analyze short-term and long-term effects of the interventions. Additionally, a process evaluation and a cost-effectiveness analysis will be carried out. The DISCovery project fulfills a strong need for theory-driven and scientifically well-performed research on job stress and performance interventions. It will provide insight into (1) how a balance between job demands, job resources, and recovery from work can be optimized, (2) the short-term and long-term effects of tailored work-oriented effects, and (3) indicators for successful or unsuccessful implementation of interventions.

Shaping the Social: design of a settings-based intervention study to improve well-being and reduce smoking and dropout in Danish vocational schools.

PubMed

Andersen, Susan; Tolstrup, Janne Schurmann; Rod, Morten Hulvej; Ersbøll, Annette Kjær; Sørensen, Betina Bang; Holmberg, Teresa; Johansen, Christoffer; Stock, Christiane; Laursen, Bjarne; Zinckernagel, Line; Øllgaard, Anne Louise; Ingholt, Liselotte

2015-06-20

The social environment at schools is an important setting to promote educational attainment, and health and well-being of young people. However, within upper secondary education there is a need for evidence-based school intervention programmes. The Shaping the Social intervention is a comprehensive programme integrating social and educational activities to promote student well-being and reduce smoking and dropout in upper secondary vocational education. The evaluation design is reported here. The evaluation employed a non-randomised cluster controlled design, and schools were selected to either implement the intervention or continue with normal practice for comparison. In the baseline survey conducted 2011-2012, 2,329 students from four intervention schools and 3,371 students from six comparison schools answered a computer-based questionnaire during class, representing 73% and 81% of eligible students, and 22% of all technical/agricultural vocational schools in Denmark. Follow-up assessment was conducted 10 weeks after baseline and at the same time teachers of the intervention classes answered a questionnaire about implementation. School dropout rates will be tracked via national education registers through a 2-year follow-up period. Shaping the Social was designed to address that students at Danish vocational schools constitute a high risk population concerning health behaviour as well as school dropout by modifying the school environment, alongside developing appropriate evaluation strategies. To address difficulties in implementing settings-based interventions, as highlighted in prior research, the strategy was to involve intervention schools in the development of the intervention. Baseline differences will be included in the effectiveness analysis, so will the impact of likely mediators and moderators of the intervention. ISRCTN57822968. Date of registration: 16/01/2013.

Controlling the extrudate swell in melt extrusion additive manufacturing of 3D scaffolds: a designed experiment.

PubMed

Yousefi, Azizeh-Mitra; Smucker, Byran; Naber, Alex; Wyrick, Cara; Shaw, Charles; Bennett, Katelyn; Szekely, Sarah; Focke, Carlie; Wood, Katherine A

2018-02-01

Tissue engineering using three-dimensional porous scaffolds has shown promise for the restoration of normal function in injured and diseased tissues and organs. Rigorous control over scaffold architecture in melt extrusion additive manufacturing is highly restricted mainly due to pronounced variations in the deposited strand diameter upon any variations in process conditions and polymer viscoelasticity. We have designed an I-optimal, split-plot experiment to study the extrudate swell in melt extrusion additive manufacturing and to control the scaffold architecture. The designed experiment was used to generate data to relate three responses (swell, density, and modulus) to a set of controllable factors (plotting needle diameter, temperature, pressure, and the dispensing speed). The fitted regression relationships were used to optimize the three responses simultaneously. The swell response was constrained to be close to 1 while maximizing the modulus and minimizing the density. Constraining the extrudate swell to 1 generates design-driven scaffolds, with strand diameters equal to the plotting needle diameter, and allows a greater control over scaffold pore size. Hence, the modulus of the scaffolds can be fully controlled by adjusting the in-plane distance between the deposited strands. To the extent of the model's validity, we can eliminate the effect of extrudate swell in designing these scaffolds, while targeting a range of porosity and modulus appropriate for bone tissue engineering. The result of this optimization was a predicted modulus of 14 MPa and a predicted density of 0.29 g/cm 3 (porosity ≈ 75%) using polycaprolactone as scaffold material. These predicted responses corresponded to factor levels of 0.6 μm for the plotting needle diameter, plotting pressure of 2.5 bar, melt temperature of 113.5 °C, and dispensing speed of 2 mm/s. The validation scaffold enabled us to quantify the percentage difference for the predictions, which was 9.5% for the

Large Advanced Space Systems (LASS) computer-aided design program additions

NASA Technical Reports Server (NTRS)

Farrell, C. E.

1982-01-01

The LSS preliminary and conceptual design requires extensive iteractive analysis because of the effects of structural, thermal, and control intercoupling. A computer aided design program that will permit integrating and interfacing of required large space system (LSS) analyses is discussed. The primary objective of this program is the implementation of modeling techniques and analysis algorithms that permit interactive design and tradeoff studies of LSS concepts. Eight software modules were added to the program. The existing rigid body controls module was modified to include solar pressure effects. The new model generator modules and appendage synthesizer module are integrated (interfaced) to permit interactive definition and generation of LSS concepts. The mass properties module permits interactive specification of discrete masses and their locations. The other modules permit interactive analysis of orbital transfer requirements, antenna primary beam n, and attitude control requirements.

75 FR 64781 - Additional Designations, Foreign Narcotics Kingpin Designation Act

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-20

... Act. The list of additional designees is as follows: 1. JR CONTROLADORA DE RESTAURANTES, S.A. DE C.V...; Folio Mercantil No. 345497 (Mexico); (ENTITY) [BPI-SDNTK] 3. FLORBEL OPERADORA DE RESTAURANTES, S.A. DE...

The hub-and-spoke organization design: an avenue for serving patients well.

PubMed

Elrod, James K; Fortenberry, John L

2017-07-11

The healthcare industry is characterized by intensive, never-ending change occurring on a multitude of fronts. Success in such tumultuous environments requires healthcare providers to be proficient in myriad areas, including the manner in which they organize and deliver services. Less efficient designs drain precious resources and hamper efforts to deliver the best care possible to patients, making it imperative that optimal pathways are identified and pursued. One particular avenue that offers great potential for serving patients efficiently and effectively is known as the hub-and-spoke organization design. The hub-and-spoke organization design is a model which arranges service delivery assets into a network consisting of an anchor establishment (hub) which offers a full array of services, complemented by secondary establishments (spokes) which offer more limited service arrays, routing patients needing more intensive services to the hub for treatment. Hub-and-spoke networks afford many benefits for healthcare providers, but in order to capitalize fully, proper assembly is required. To advance awareness, knowledge, and use of the hub-and-spoke organization design, this article profiles Willis-Knighton Health System's service delivery network which has utilized the model for over three decades. Among other things, the hub-and-spoke organization design is defined, benefits are stipulated, and applications are discussed, permitting healthcare providers essential insights for the establishment and operation of these networks. The change-rich nature of the healthcare industry places a premium on incorporating advancements that permit health and medical providers to operate as optimally as possible. The hub-and-spoke organization design represents an option that, when deployed correctly, can greatly assist healthcare establishments in their quests to serve patients well.

Practical application of economic well-performance criteria to the optimization of fracturing treatment design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anderson, R.W.; Phillips, A.M.

1988-02-01

Low-permeability reservoirs are currently being propped with sand, resin-coated sand, intermediate-density proppants, and bauxite. This wide range of proppant cost and performance has resulted in a proliferation of proppant selection models. Initially, a rather vague relationship between well depth and proppant strength dictated the choice of proppant. More recently, computerized models of varying complexity have become available that use net-present-value (NPV) calculations. The input is based on the operator's performance goals for each well and on specific reservoir properties. Simpler, noncomputerized approaches also being used include cost/performance comparisons and nomographs. Each type of model, including several of the computerized models,more » will be examined. By use of these models and NPV calculations, optimum fracturing treatment designs have been developed for such low-permeability reservoirs as the Prue in Oklahoma. Typical well conditions are used in each of the selection models and the results are compared. The computerized models allow the operator to determine, before fracturing, how changes in proppant type, size, and quantity will affect postfracture production over time periods ranging from several months to many years. Thus, the operator can choose the fracturing treatment design that best satisfies the economic performance goals for a particular well, regardless of whether those goals are long or short term.« less

Designed Single-Step Synthesis, Structure, and Derivative Textural Properties of Well-Ordered Layered Penta-Coordinate Silicon Alcoholate Complexes

PubMed Central

Li, Xiansen; Michaelis, Vladimir K.; Ong, Ta-Chung; Smith, Stacey J.; Griffin, Robert G.; Wang, Evelyn N.

2014-01-01

The controllable synthesis of well-ordered layered materials with specific nanoarchitecture poses a grand challenge in materials chemistry. We report the solvothermal synthesis of two structurally analogous 5-coordinate organosilicate complexes via a novel transesterification mechanism. Since the polycrystalline nature of the intrinsic hypervalent Si complex thwarts the endeavor in determining its structure, a novel strategy concerning the elegant addition of a small fraction of B species as an effective crystal growth mediator and a sacrificial agent is proposed to directly prepare diffraction-quality single crystals without disrupting the intrinsic elemental type. In the determined crystal structure, two monomeric primary building units (PBUs) self-assemble into a dimeric asymmetric secondary BU via strong Na+-O2− ionic bonds. The designed one-pot synthesis is straightforward, robust, and efficient, leading to a well-ordered (10ī)-parallel layered Si complex with its principal interlayers intercalated with extensive van der Waals gaps in spite of the presence of substantial Na+ counterions as a result of unique atomic arrangement in its structure. On the other hand, upon fast pyrolysis, followed by acid leaching, both complexes are converted into two SiO2 composites bearing BET surface areas of 163.3 and 254.7 m2 g−1 for the pyrolyzed intrinsic and B-assisted Si complexes, respectively. The transesterification methodology merely involving alcoholysis but without any hydrolysis side reaction is designed to have generalized applicability for use in synthesizing new layered metal-organic compounds with tailored PBUs and corresponding metal oxide particles with hierarchical porosity. PMID:24737615

76 FR 5857 - Additional Designations, Foreign Narcotics Kingpin Designation Act

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-02

... Act. The list of additional designees is as follows: 1. KHARROUBI, Ali Mohamed (a.k.a. KHAROUBI, Ali; a.k.a. ``KAROBY, Ali''), c/o SOLMAR, Lebanon; c/o ELLISSA HOLDING, Lebanon; c/o ELLISSA GROUP SA...

Rare-Variant Association Analysis: Study Designs and Statistical Tests

PubMed Central

Lee, Seunggeung; Abecasis, Gonçalo R.; Boehnke, Michael; Lin, Xihong

2014-01-01

Despite the extensive discovery of trait- and disease-associated common variants, much of the genetic contribution to complex traits remains unexplained. Rare variants can explain additional disease risk or trait variability. An increasing number of studies are underway to identify trait- and disease-associated rare variants. In this review, we provide an overview of statistical issues in rare-variant association studies with a focus on study designs and statistical tests. We present the design and analysis pipeline of rare-variant studies and review cost-effective sequencing designs and genotyping platforms. We compare various gene- or region-based association tests, including burden tests, variance-component tests, and combined omnibus tests, in terms of their assumptions and performance. Also discussed are the related topics of meta-analysis, population-stratification adjustment, genotype imputation, follow-up studies, and heritability due to rare variants. We provide guidelines for analysis and discuss some of the challenges inherent in these studies and future research directions. PMID:24995866

AEROSOL PARTICLE COLLECTOR DESIGN STUDY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, S; Richard Dimenna, R

2007-09-27

A computational evaluation of a particle collector design was performed to evaluate the behavior of aerosol particles in a fast flowing gas stream. The objective of the work was to improve the collection efficiency of the device while maintaining a minimum specified air throughput, nominal collector size, and minimal power requirements. The impact of a range of parameters was considered subject to constraints on gas flow rate, overall collector dimensions, and power limitations. Potential improvements were identified, some of which have already been implemented. Other more complex changes were identified and are described here for further consideration. In addition, fruitfulmore » areas for further study are proposed.« less

76 FR 68459 - Designation of a Class of Employees for Addition to the Special Exposure Cohort

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-04

... designate a class of employees from W.R. Grace and Company in Curtis Bay, Maryland, as an addition to the... by W.R. Grace and Company in Curtis Bay, Maryland, for the operational period from May 1, 1956...

Integrating Sustainability Science with the Sciences of Human Well-being to Inform Design and Planning in an Urbanizing World

NASA Astrophysics Data System (ADS)

Alberti, M.; Graumlich, L. J.; Frumkin, H.; Friedman, D.

2012-12-01

A sustainable human future requires both healthy ecosystems and communities in which people thrive, with opportunities for health, well-being, happiness, economic prosperity, and equity. To make progress towards this goal, two largely disparate communities of scholars and practitioners must come together: sustainability science needs to be integrated with the sciences of human health and well-being. The opportunity for such integration is particularly ripe for urbanizing regions which not only dominate energy and resource use but also increasingly represent the human habitat. We present a conceptual framework that integrates sustainability science with the sciences of human health and well-being to explicitly articulate testable hypotheses on the relationships between humans and their habitat. We are interested in human behaviors and metrics of health and well-being in relationship to the characteristics of the built environment at various scales from buildings to metro regions. Focusing on the U.S. Pacific Northwest (PNW) as a testbed, we are building on our current empirical studies on urban sprawl and ecosystem function including biodiversity, air quality, hydrological, biogeochemical, and human health to develop formal hypotheses on how alternative urban design and development patterns may influence health outcomes and well-being. The PNW is an ideal setting for this work because of the connected metropolitan areas within a region characterized by a spectacular diversity of aquatic and terrestrial ecosystems and deeply held cultural and political aspirations towards sustainability. The framework also highlights opportunities for translation of knowledge to practice in the design and planning of built environments. For example, understanding these associations is critical to assessing tradeoffs in design and planning strategies and exploring potential synergies that optimize both sustainability and human well-being. In complex systems such as cities, managers

Child Wellness and Happiness

ERIC Educational Resources Information Center

Rettew, David C.

2009-01-01

Wellness and happiness should be considered in the clinical treatment of child and adolescent psychiatry, in addition with thinking about illness. Meanwhile, various studies on child and adolescent psychiatry,which includes an article from the "Journal of Happiness Studies," are discussed.

78 FR 9997 - Additional Designations, Foreign Narcotics Kingpin Designation Act

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-12

... the President to impose sanctions against significant foreign narcotics traffickers and their... controlled by significant foreign narcotics traffickers as identified by the President. In addition, the..., Rio Grande, Zacatecas 98400, Mexico; Matamoros, Tamaulipas, Mexico; Rio Grande, Zacatecas, Mexico; DOB...

D-OPTIMAL EXPERIMENTAL DESIGNS TO TEST FOR DEPARTURE FROM ADDITIVITY IN A FIXED-RATIO MIXTURE RAY.

EPA Science Inventory

Humans are exposed to mixtures of environmental compounds. A regulatory assumption is that the mixtures of chemicals act in an additive manner. However, this assumption requires experimental validation. Traditional experimental designs (full factorial) require a large number of e...

The study of health coaching: the ithaca coaching project, research design, and future directions.

PubMed

Sforzo, Gary A

2013-05-01

Health coaching (HC) is a process holding tremendous potential as a complementary medical intervention to shape healthy behavior change and affect rates of chronic lifestyle diseases. Empirical knowledge of effectiveness for the HC process, however, is lacking. The purposes of this paper are to present the study protocol for the Ithaca Coaching Project while also addressing research design, methodological issues, and directions for HC research. This is one of the first large-scale, randomized control trials of HC for primary prevention examining impact on physical and emotional health status in an employee population. An additional intent for the project is to investigate self-determination theory as a theoretical framework for the coaching process. Participants (n=300) are recruited as part of a campus-wide wellness initiative and randomly assigned to one of three levels of client-centered HC or a control with standard wellness program care. Repeated measures analyses of covariance will be used to examine coaching effectiveness while path analyses will be used to examine relationships between coaching processes, self-determination variables, and health outcomes. There is a great need for well-designed HC studies that define coaching best practices, examine intervention effectiveness, provide cost:benefit analysis, and address scope of practice. This information will allow a clearer definition of HC to emerge and determination of if, and how, HC fits in modern-day healthcare. This is an exciting but critical time for HC research and for the practice of HC.

The Study of Health Coaching: The Ithaca Coaching Project, Research Design, and Future Directions

PubMed Central

2013-01-01

Health coaching (HC) is a process holding tremendous potential as a complementary medical intervention to shape healthy behavior change and affect rates of chronic lifestyle diseases. Empirical knowledge of effectiveness for the HC process, however, is lacking. The purposes of this paper are to present the study protocol for the Ithaca Coaching Project while also addressing research design, methodological issues, and directions for HC research. This is one of the first large-scale, randomized control trials of HC for primary prevention examining impact on physical and emotional health status in an employee population. An additional intent for the project is to investigate self-determination theory as a theoretical framework for the coaching process. Participants (n=300) are recruited as part of a campus-wide wellness initiative and randomly assigned to one of three levels of client-centered HC or a control with standard wellness program care. Repeated measures analyses of covariance will be used to examine coaching effectiveness while path analyses will be used to examine relationships between coaching processes, self-determination variables, and health outcomes. There is a great need for well-designed HC studies that define coaching best practices, examine intervention effectiveness, provide cost:benefit analysis, and address scope of practice. This information will allow a clearer definition of HC to emerge and determination of if, and how, HC fits in modern-day healthcare. This is an exciting but critical time for HC research and for the practice of HC. PMID:24416673

Topological design and additive manufacturing of porous metals for bone scaffolds and orthopaedic implants: A review.

PubMed

Wang, Xiaojian; Xu, Shanqing; Zhou, Shiwei; Xu, Wei; Leary, Martin; Choong, Peter; Qian, M; Brandt, Milan; Xie, Yi Min

2016-03-01

One of the critical issues in orthopaedic regenerative medicine is the design of bone scaffolds and implants that replicate the biomechanical properties of the host bones. Porous metals have found themselves to be suitable candidates for repairing or replacing the damaged bones since their stiffness and porosity can be adjusted on demands. Another advantage of porous metals lies in their open space for the in-growth of bone tissue, hence accelerating the osseointegration process. The fabrication of porous metals has been extensively explored over decades, however only limited controls over the internal architecture can be achieved by the conventional processes. Recent advances in additive manufacturing have provided unprecedented opportunities for producing complex structures to meet the increasing demands for implants with customized mechanical performance. At the same time, topology optimization techniques have been developed to enable the internal architecture of porous metals to be designed to achieve specified mechanical properties at will. Thus implants designed via the topology optimization approach and produced by additive manufacturing are of great interest. This paper reviews the state-of-the-art of topological design and manufacturing processes of various types of porous metals, in particular for titanium alloys, biodegradable metals and shape memory alloys. This review also identifies the limitations of current techniques and addresses the directions for future investigations. Copyright © 2016 Elsevier Ltd. All rights reserved.

77 FR 36041 - Additional Designations, Foreign Narcotics Kingpin Designation Act

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-15

... identified by the President. In addition, the Secretary of the Treasury, in consultation with the Attorney.... 222, Colonia Ciudad del Sol, Zapopan, Jalisco 45050, Mexico; Calle Quebec 606 B, Prados Providencia, Guadalajara, Jalisco, Mexico; Calle Mango 2129, Colonia Paraisos del Colli, Guadalajara, Jalisco, Mexico...

76 FR 58562 - Additional Designations, Foreign Narcotics Kingpin Designation Act

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-21

... controlled by significant foreign narcotics traffickers as identified by the President. In addition, the..., Jalisco, Mexico; Plaza Del Sol Local 28, Zona R, Guadalajara, Jalisco, Mexico; Paseo Del Heliotropo 3426, Monraz, Guadalajara, Jalisco, Mexico; DOB 09 Aug 1955; POB Jalisco, Mexico; Citizen Mexico; Nationality...

77 FR 71480 - Additional Designations, Foreign Narcotics Kingpin Designation Act

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-30

... controlled by significant foreign narcotics traffickers as identified by the President. In addition, the... IBARRA, Mayela), Calle Lago de La Doga 5312, Tijuana, Baja California, Mexico; DOB 24 Feb 1961; POB Coahuila, Mexico; Passport 99020046985 (Mexico); R.F.C. CAIM610224 (Mexico) (individual) [SDNTK]. 2...

Studies for understanding effects of additions on the strength of cement concrete

NASA Astrophysics Data System (ADS)

Bucur, R. D.; Barbuta, M.; Konvalina, P.; Serbanoiu, A. A.; Bernas, J.

2017-09-01

The paper analyzes the effects of different types of additions introduced in concrete mix on the compressive strength. The current studies show that additions contribute to improve some characteristics of concrete and to reduce the cement dosage, so it can obtain concretes which are cheaper and friendlier with environment. In the experimental mixes were introduced: crushed natural aggregates, slag aggregates, silica fume, fly ash, chopped tire, polystyrene granule, glass fibers and metallic fibers. The experimental values of compressive strengths were compared for two concrete grades (C20/25 and C25/30). The study shown that near the well-known possibilities of improving mechanical strengths of cement concrete by increasing cement dosage and strength, by using crushed aggregates and by reducing the water/cement ratio, there are other methods in which less cement is used by replacing it with different wastes or by adding fiber.

78 FR 68687 - Final Additional Airworthiness Design Standards: Advanced Avionics Under the Special Class (JAR...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-15

... under Sec. 21.17(b), to Day-VFR operations. Additionally, the FAA also published design criteria to allow expansion of the Aquila AT01-100 airplane to include Night-VFR as shown in NPRM 75 FR 32576. In conjunction with the expansion to Night-VFR operations integrated avionic displays are to be installed on the...

Wellness Interventions for School Counselors: A Case-Study in Treating Asperger's Disorder

ERIC Educational Resources Information Center

Hartwig Moorhead, Holly J.; Green, Judy; McQuistion, Rick R.; Ozimek, Barbara

2008-01-01

The Five Factor Wellness Inventory-Elementary Version (5F-WEL -E) was used in a pre- and post-test design to determine the wellness of a 13 year-old male with Asperger's Disorder. Wellness in the Creative and Physical Self domains was low. Thus, the school counselor implemented a 5-month treatment plan, based upon the Wheel of Wellness, in the…

75 FR 34214 - Additional Designations, Foreign Narcotics Kingpin Designation Act

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-16

... organizations on a worldwide basis. It provides a statutory framework for the President to impose sanctions... traffickers as identified by the President. In addition, the Secretary of the Treasury consults with the... Italia, Michoac[aacute]n, Mexico; Calle Articulo 123 Numero 103, Colonia Centro, Nueva Italia, Michoac...

77 FR 2347 - Additional Designations, Foreign Narcotics Kingpin Designation Act

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-17

... identified by the President. In addition, the Secretary of the Treasury, in consultation with the Attorney.... 80010, Mexico; Boulevard Universitarios No. 789, Local 4, Colonia Villa Universidad, Culiacan, Sinaloa C.P. 80010, Mexico; Localidad San Jose del Barranco S/N, Badiraguato, Sinaloa C.P. 80500, Mexico; DOB...

78 FR 8701 - Additional Designations, Foreign Narcotics Kingpin Designation Act

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-06

... Security may designate and block the property and interests in property, subject to U.S. jurisdiction, of persons who are found to be: (1) Materially assisting in, or providing financial or technological support.... ``DIEGO RASTROJO''); DOB 07 Apr 1971; POB Bolivar, Valle de Cauca, Colombia; nationality Colombia; citizen...

77 FR 14859 - Additional Designations, Foreign Narcotics Kingpin Designation Act

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-13

... of State, and the Secretary of Homeland Security when designating and blocking the property and... assisting in, or providing financial or technological support for or to, or providing goods or services in.... BAQBANI, Mohammad Akhusa); DOB 5 Jan 1961; alt. DOB 1947; POB Zabol, Iran; citizen Iran; Islamic...

77 FR 48609 - Additional Designations, Foreign Narcotics Kingpin Designation Act

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-14

... the names of three individuals and five entities whose property and interests in property have been... designation by the Director of OFAC of the three individuals and five entities identified in this notice... transactions involving U.S. companies and individuals. The Kingpin Act blocks all property and interests in...

Non-additivity of functional group contributions in protein-ligand binding: a comprehensive study by crystallography and isothermal titration calorimetry.

PubMed

Baum, Bernhard; Muley, Laveena; Smolinski, Michael; Heine, Andreas; Hangauer, David; Klebe, Gerhard

2010-04-09

Additivity of functional group contributions to protein-ligand binding is a very popular concept in medicinal chemistry as the basis of rational design and optimized lead structures. Most of the currently applied scoring functions for docking build on such additivity models. Even though the limitation of this concept is well known, case studies examining in detail why additivity fails at the molecular level are still very scarce. The present study shows, by use of crystal structure analysis and isothermal titration calorimetry for a congeneric series of thrombin inhibitors, that extensive cooperative effects between hydrophobic contacts and hydrogen bond formation are intimately coupled via dynamic properties of the formed complexes. The formation of optimal lipophilic contacts with the surface of the thrombin S3 pocket and the full desolvation of this pocket can conflict with the formation of an optimal hydrogen bond between ligand and protein. The mutual contributions of the competing interactions depend on the size of the ligand hydrophobic substituent and influence the residual mobility of ligand portions at the binding site. Analysis of the individual crystal structures and factorizing the free energy into enthalpy and entropy demonstrates that binding affinity of the ligands results from a mixture of enthalpic contributions from hydrogen bonding and hydrophobic contacts, and entropic considerations involving an increasing loss of residual mobility of the bound ligands. This complex picture of mutually competing and partially compensating enthalpic and entropic effects determines the non-additivity of free energy contributions to ligand binding at the molecular level. (c) 2010 Elsevier Ltd. All rights reserved.

78 FR 29814 - Additional Designations, Foreign Narcotics Kingpin Designation Act

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-21

... identified by the President. In addition, the Secretary of the Treasury, in consultation with the Attorney..., Ciudad Acuna, Coahuila, Mexico; DOB 30 Dec 1973; POB Ciudad Acuna, Coahuila, Mexico; alt. POB Coahuila, Mexico; nationality Mexico; citizen Mexico; C.U.R.P. AAPA731230HCLNRL07 (Mexico) (individual) [SDNTK...

78 FR 62946 - Additional Designations, Foreign Narcotics Kingpin Designation Act

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-22

... significant foreign narcotics traffickers as identified by the President. In addition, the Secretary of the...; R.F.C. PAPA751109870 (Mexico); C.U.R.P. PAPA751109HNEDSL04 (Mexico) (individual) [SDNTK] (Linked To... No. 279, Supermanzana 50, Manzana 14, Lote 17, Residencial San Angel, Cancun, Quintana Roo, Mexico...

78 FR 47828 - Additional Designations, Foreign Narcotics Kingpin Designation Act

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-06

... significant foreign narcotics traffickers as identified by the President. In addition, the Secretary of the..., Colonia Centro, Culiacan, Sinaloa 80000, Mexico; DOB 21 Dec 1941; POB Sinaloa, Mexico; nationality Mexico; citizen Mexico; R.F.C. NUBA411221867 (Mexico); C.U.R.P. NUBA411221HSLXDN05 (Mexico) (individual) [SDNTK...

A kinetic study of struvite precipitation recycling technology with NaOH/Mg(OH)2 addition.

PubMed

Yu, Rongtai; Ren, Hongqiang; Wang, Yanru; Ding, Lili; Geng, Jingji; Xu, Ke; Zhang, Yan

2013-09-01

Struvite precipitation recycling technology is received wide attention in removal ammonium and phosphate out of wastewater. While past study focused on process efficiency, and less on kinetics. The kinetic study is essential for the design and optimization in the application of struvite precipitation recycling technology. The kinetics of struvite with NaOH/Mg(OH)2 addition were studied by thermogravimetry analysis with three rates (5, 10, 20 °C/min), using Friedman method and Ozawa-Flynn-Wall method, respectively. Degradation process of struvite with NaOH/Mg(OH)2 addition was three steps. The stripping of ammonia from struvite was mainly occurred at the first step. In the first step, the activation energy was about 70 kJ/mol, which has gradually declined as the reaction progress. By model fitting studies, the proper mechanism function for struvite decomposition process with NaOH/Mg(OH)2 addition was revealed. The mechanism function was f(α)=α(α)-(1-α)(n), a Prout-Tompkins nth order (Bna) model. Copyright © 2013 Elsevier Ltd. All rights reserved.

European isolation and confinement study. Additional experiments.

PubMed

Novara, M

1993-01-01

Microbiological Experiments. The ISEMSI microbiological contamination experiments confirmed known hypotheses, such as: the trend toward uniformity of skin microbial flora across a group of individuals enclosed together; the rather fast "colonization" of the environment by microorganisms shed by human inhabitants; and the heavy growth of microorganisms in poorly accessible and wet areas (toilets, air conditioning). In addition, possible disturbances of skin defense mechanisms against colonization by potentially pathogenic microbes were noted, as well as a difficulty in monitoring the microbial contents of the atmosphere (significant random variations occur between samples taken at different times and locations). Sensors for Atmospheric Contaminants. Several different prototypes of "array sensors" for the monitoring of trace gas contaminants in the atmosphere were evaluated during ISEMSI. Their performance was promising when compared with results achieved with a more conventional (and more complex) gas chromatograph/mass spectrometer device, also used during ISEMSI. An overall picture of the most important chemical contaminants to be found in enclosed, manned habitats (including contaminants produced by man himself) was obtained via the use of Tenax gas-adsorption traps. This permitted monitoring the fluctuation of contaminants on a daily basis, as well as during the complete 4-week period. Results will provide a valuable input for designing systems to monitor and control atmospheric contamination in future spacecraft. Particular attention was devoted to the monitoring of carbon monoxide in the chamber. Results showing the correlation between its concentration in the atmosphere and the percentage of carboxyhemoglobin in the EMSInauts' blood will allow the evaluation of the correctness of the presently specified maximum allowable concentration for spacecraft. Telemedicine Experiment. The telemedicine experiment confirmed the feasibility and importance of applying to a

Case-Cohort Studies: Design and Applicability to Hand Surgery.

PubMed

Vojvodic, Miliana; Shafarenko, Mark; McCabe, Steven J

2018-04-24

Observational studies are common research strategies in hand surgery. The case-cohort design offers an efficient and resource-friendly method for risk assessment and outcomes analysis. Case-cohorts remain underrepresented in upper extremity research despite several practical and economic advantages over case-control studies. This report outlines the purpose, utility, and structure of the case-cohort design and offers a sample research question to demonstrate its value to risk estimation for adverse surgical outcomes. The application of well-designed case-cohort studies is advocated in an effort to improve the quality and quantity of observational research evidence in hand and upper extremity surgery. Copyright © 2018 American Society for Surgery of the Hand. Published by Elsevier Inc. All rights reserved.

Cryogenic Propellant Management Device: Conceptual Design Study

NASA Technical Reports Server (NTRS)

Wollen, Mark; Merino, Fred; Schuster, John; Newton, Christopher

2010-01-01

Concepts of Propellant Management Devices (PMDs) were designed for lunar descent stage reaction control system (RCS) and lunar ascent stage (main and RCS propulsion) missions using liquid oxygen (LO2) and liquid methane (LCH4). Study ground rules set a maximum of 19 days from launch to lunar touchdown, and an additional 210 days on the lunar surface before liftoff. Two PMDs were conceptually designed for each of the descent stage RCS propellant tanks, and two designs for each of the ascent stage main propellant tanks. One of the two PMD types is a traditional partial four-screen channel device. The other type is a novel, expanding volume device which uses a stretched, flexing screen. It was found that several unique design features simplified the PMD designs. These features are (1) high propellant tank operating pressures, (2) aluminum tanks for propellant storage, and (3) stringent insulation requirements. Consequently, it was possible to treat LO2 and LCH4 as if they were equivalent to Earth-storable propellants because they would remain substantially subcooled during the lunar mission. In fact, prelaunch procedures are simplified with cryogens, because any trapped vapor will condense once the propellant tanks are pressurized in space.

75 FR 44311 - Additional Designations, Foreign Narcotics Kingpin Designation Act

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-28

... basis. It provides a statutory framework for the President to impose sanctions against significant... identified by the President. In addition, the Secretary of the Treasury consults with the Attorney General... of designees is as follows: Entities: 1. ARTE Y DISENO DE CULIACAN S.A. DE C.V., Calle Rio Santa...

A Well Designed School Environment Facilitates Brain Learning.

ERIC Educational Resources Information Center

Chan, Tak Cheung; Petrie, Garth

2000-01-01

Examines how school design facilitates learning by complementing how the brain learns. How the brain learns is discussed and how an artistic environment, spaciousness in the learning areas, color and lighting, and optimal thermal and acoustical environments aid student learning. School design suggestions conclude the article. (GR)

Optimal design of studies of influenza transmission in households. I: case-ascertained studies.

PubMed

Klick, B; Leung, G M; Cowling, B J

2012-01-01

Case-ascertained household transmission studies, in which households including an 'index case' are recruited and followed up, are invaluable to understanding the epidemiology of influenza. We used a simulation approach parameterized with data from household transmission studies to evaluate alternative study designs. We compared studies that relied on self-reported illness in household contacts vs. studies that used home visits to collect swab specimens for virological confirmation of secondary infections, allowing for the trade-off between sample size vs. intensity of follow-up given a fixed budget. For studies estimating the secondary attack proportion, 2-3 follow-up visits with specimens collected from all members regardless of illness were optimal. However, for studies comparing secondary attack proportions between two or more groups, such as controlled intervention studies, designs with reactive home visits following illness reports in contacts were most powerful, while a design with one home visit optimally timed also performed well.

Quality-by-design case study: investigation of the role of poloxamer in immediate-release tablets by experimental design and multivariate data analysis.

PubMed

Kaul, Goldi; Huang, Jun; Chatlapalli, Ramarao; Ghosh, Krishnendu; Nagi, Arwinder

2011-12-01

The role of poloxamer 188, water and binder addition rate, on retarding dissolution in immediate-release tablets of a model drug from BCS class II was investigated by means of multivariate data analysis (MVDA) combined with design of experiments (DOE). While the DOE analysis yielded important clues into the cause-and-effect relationship between the responses and design factors, multivariate data analysis of the 40+ variables provided additional information on slowdown in tablet dissolution. A steep dependence of both tablet dissolution and disintegration on the poloxamer and less so on other design variables was observed. Poloxamer was found to increase dissolution rates in granules as expected of surfactants in general but retard dissolution in tablets. The unexpected effect of poloxamer in tablets was accompanied by an increase in tablet-disintegration-time-mediated slowdown of tablet dissolution and by a surrogate binding effect of poloxamer at higher concentrations. It was additionally realized through MVDA that poloxamer in tablets either acts as a binder by itself or promotes binder action of the binder povidone resulting in increased intragranular cohesion. Additionally, poloxamer was found to mediate tablet dissolution on stability as well. In contrast to tablet dissolution at release (time zero), poloxamer appeared to increase tablet dissolution in a concentration-dependent manner on accelerated open-dish stability. Substituting polysorbate 80 as an alternate surfactant in place of poloxamer in the formulation was found to stabilize tablet dissolution.

77 FR 14592 - Additional Designations, Foreign Narcotics Kingpin Designation Act

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-12

... controlled by significant foreign narcotics traffickers as identified by the President. In addition, the...''), DOB 13 Aug 1961; POB Culiacan, Sinaloa, Mexico; citizen Mexico; nationality Mexico; C.U.R.P. ZAGJ610813HSLMRS05 (Mexico) (individual) [SDNTK] Entities 2. ZARKA DE MEXICO S.A. DE C.V., Miguel Hidalgo No. 348 Pte...

Conceptual design studies for surface infrastructure

NASA Technical Reports Server (NTRS)

Bufkin, Ann L.; Jones, William R., II

1986-01-01

The utimate design of a manned Mars base will be the result of considerable engineering analysis and many trade studies to optimize the configuration. Many options and scenarios are available and all need to be considered at this time. Initial base elements, two base configuration concepts, internal space architectural concerns, and two base set-up scenarios are discussed. There are many variables as well as many unknowns to be reckoned with before people set foot on the red planet.

Wellness-Promoting Practices Through Girl Scouts: A Pragmatic Superiority Randomized Controlled Trial With Additional Dissemination.

PubMed

Cull, Brooke J; Dzewaltowski, David A; Guagliano, Justin M; Rosenkranz, Sara K; Knutson, Cassandra K; Rosenkranz, Richard R

2018-01-01

To evaluate the effectiveness of in-person versus online Girl Scout leader wellness training for implementation of wellness-promoting practices during troop meetings (phase I) and to assess training adoption and current practices across the council (phase II). Pragmatic superiority trial (phase 1) followed by serial cross-sectional study (phase II). Girl Scout troop meetings in Northeast Kansas. Eighteen troop leaders from 3 counties (phase 1); 113 troop leaders from 7 counties (phase II). Phase I: Troop leaders attended 2 wellness training sessions (first in groups, second individually), wherein leaders set wellness-promoting practice implementation goals, self-monitored progress, and received guidance and resources for implementation. Leaders received the intervention in person or online. Phase I: At baseline and postintervention, leaders completed a wellness-promoting practice implementation questionnaire assessing practices during troop meetings (max score = 11). Phase II: Leaders completed a survey about typical troop practices and interest in further training. Phase I: Generalized linear mixed modeling. Phase I: In-person training increased wellness-promoting practice implementation more than online training (in person = 2.1 ± 1.8; online = 0.2 ± 1.2; P = .022). Phase II: Fifty-six percent of leaders adopted the training. For 8 of 11 wellness categories, greater than 50% of leaders employed wellness-promoting practices. In-person training was superior to online training for improvements in wellness-promoting practices. Wellness training was adopted by the majority of leaders across the council.

Implications of Two Well-Known Models for Instructional Designers in Distance Education: Dick-Carey versus Morrison-Ross-Kemp

ERIC Educational Resources Information Center

Akbulut, Yavuz

2007-01-01

This paper first summarizes, and then compares and contrasts two well-known instructional design models: Dick and Carey Model (DC) and Morrison, Ross and Kemp model (MRK). The target audiences of both models are basically instructional designers. Both models have applications for different instructional design settings. They both see the…

A Multi-Scale, Multi-Physics Optimization Framework for Additively Manufactured Structural Components

NASA Astrophysics Data System (ADS)

El-Wardany, Tahany; Lynch, Mathew; Gu, Wenjiong; Hsu, Arthur; Klecka, Michael; Nardi, Aaron; Viens, Daniel

This paper proposes an optimization framework enabling the integration of multi-scale / multi-physics simulation codes to perform structural optimization design for additively manufactured components. Cold spray was selected as the additive manufacturing (AM) process and its constraints were identified and included in the optimization scheme. The developed framework first utilizes topology optimization to maximize stiffness for conceptual design. The subsequent step applies shape optimization to refine the design for stress-life fatigue. The component weight was reduced by 20% while stresses were reduced by 75% and the rigidity was improved by 37%. The framework and analysis codes were implemented using Altair software as well as an in-house loading code. The optimized design was subsequently produced by the cold spray process.

77 FR 56271 - Additional Designations, Foreign Narcotics Kingpin Designation Act

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-12

... identified by the President. In addition, the Secretary of the Treasury, in consultation with the Attorney..., Fraccionamiento Colinas de San Miguel, Culiacan, Sinaloa, Mexico; DOB 19 Aug 1959; alt. DOB 30 Dec 1966; POB Sinaloa, Mexico; nationality Mexico; citizen Mexico; C.U.R.P. LOPG590819MSLPRR04 (Mexico); alt. C.U.R.P...

Resources for work-related well-being: a qualitative study about healthcare employees' experiences of relationships at work.

PubMed

Schön Persson, Sophie; Nilsson Lindström, Petra; Pettersson, Pär; Nilsson, Marie; Blomqvist, Kerstin

2018-05-23

The aim of this study was to explore municipal healthcare employees' experiences of relationships with care recipients and colleagues. The specific research questions were when do the relationships enhance well-being, and what prerequisites are needed for such relationships to occur?. Employees in health and social care for older people often depict their work in negative terms, and they often take a high number of sick leaves. Despite the heavy workload, other employees express well-being at work and highlight social relationships as one reason for this. However, a greater understanding of how these relationships can act as resources for workplace well-being is needed. The design of the study was qualitative and exploratory. Qualitative interview studies were conducted with twenty-three healthcare employees in municipal healthcare. Thematic analysis was used to analyse the data. Two themes were identified as resources for promoting relationships between employees and care recipients or colleagues: (i) Being personal - a close interpersonal relationship to a care recipient - and (ii) Colleague belongingness - a sense of togetherness within the working group. Spending quality time together, providing long-term care and providing additional care were antecedents for a close interpersonal relationship with care recipients. Trust, mutual responsibility and cooperation were antecedents for a sense of togetherness within the working group. The findings provide an empirical base to raise awareness of relationships with care recipients and colleagues as health aspects. Relationships among employees in healthcare are vital resources that must be considered to create sustainable workplaces, and consequently improve the quality of care. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

77 FR 9251 - Designation of a Class of Employees for Addition to the Special Exposure Cohort

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-16

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Designation of a Class of Employees for Addition to the Special Exposure Cohort AGENCY: National Institute for Occupational Safety and Health (NIOSH), Centers for..., for a number of work days aggregating at least 250 work days, occurring either solely under this...

Study of a Fine Grained Threaded Framework Design

NASA Astrophysics Data System (ADS)

Jones, C. D.

2012-12-01

Traditionally, HEP experiments exploit the multiple cores in a CPU by having each core process one event. However, future PC designs are expected to use CPUs which double the number of processing cores at the same rate as the cost of memory falls by a factor of two. This effectively means the amount of memory per processing core will remain constant. This is a major challenge for LHC processing frameworks since the LHC is expected to deliver more complex events (e.g. greater pileup events) in the coming years while the LHC experiment's frameworks are already memory constrained. Therefore in the not so distant future we may need to be able to efficiently use multiple cores to process one event. In this presentation we will discuss a design for an HEP processing framework which can allow very fine grained parallelization within one event as well as supporting processing multiple events simultaneously while minimizing the memory footprint of the job. The design is built around the libdispatch framework created by Apple Inc. (a port for Linux is available) whose central concept is the use of task queues. This design also accommodates the reality that not all code will be thread safe and therefore allows one to easily mark modules or sub parts of modules as being thread unsafe. In addition, the design efficiently handles the requirement that events in one run must all be processed before starting to process events from a different run. After explaining the design we will provide measurements from simulating different processing scenarios where the processing times used for the simulation are drawn from processing times measured from actual CMS event processing.

Implementation of Complexity Analyzing Based on Additional Effect

NASA Astrophysics Data System (ADS)

Zhang, Peng; Li, Na; Liang, Yanhong; Liu, Fang

According to the Complexity Theory, there is complexity in the system when the functional requirement is not be satisfied. There are several study performances for Complexity Theory based on Axiomatic Design. However, they focus on reducing the complexity in their study and no one focus on method of analyzing the complexity in the system. Therefore, this paper put forth a method of analyzing the complexity which is sought to make up the deficiency of the researches. In order to discussing the method of analyzing the complexity based on additional effect, this paper put forth two concepts which are ideal effect and additional effect. The method of analyzing complexity based on additional effect combines Complexity Theory with Theory of Inventive Problem Solving (TRIZ). It is helpful for designers to analyze the complexity by using additional effect. A case study shows the application of the process.

Effect of Ferrous Additives on Magnesia Stone Hydration

NASA Astrophysics Data System (ADS)

Zimich, V.

2017-11-01

The article deals with the modification of the magnesia binder with additives containing two- and three-valent iron cations which could be embedded in the chloromagnesium stone structure and also increase the strength from 60 MPa in a non-additive stone to 80MPa, water resistance from 0.58 for clear stone to 0.8 and reduce the hygroscopicity from 8% in the non-additive stone to 2% in the modified chloromagnesium stone. It is proposed to use the iron hydroxide sol as an additive in the quantities of up to 1% of the weight of the binder. The studies were carried out using the modern analysis methods: the differentialthermal and X-ray phase analysis. The structure was studied with an electron microscope with an X-ray microanalyzer. A two-factor plan-experiment was designed which allowed constructing mathematical models characterizing the influence of variable factors, such as the density of the zatcher and the amount of sol in the binder, on the basic properties of the magnesian stone. The result of the research was the magnesia stone with the claimed properties and formed from minerals characteristic for magnesian materials as well as additionally formed from amachenite and goethite. It has been established that a highly active iron hydroxide sol the ion sizes of which are commensurate with magnesium ions is actively incorporated into the structure of pentahydroxychloride and magnesium hydroxide changing the habit of crystals compacting the structure of the stone and changing its hygroscopicity.

Designing an in-situ ultrasonic nondestructive evaluation system for ultrasonic additive manufacturing

NASA Astrophysics Data System (ADS)

Nadimpalli, Venkata K.; Nagy, Peter B.

2018-04-01

Ultrasonic Additive Manufacturing (UAM) is a solid-state layer by layer manufacturing process that utilizes vibration induced plastic deformation to form a metallurgical bond between a thin layer and an existing base structure. Due to the vibration based bonding mechanism, the quality of components at each layer depends on the geometry of the structure. In-situ monitoring during and between UAM manufacturing steps offers the potential for closed-loop control to optimize process parameters and to repair existing defects. One interface that is most prone to delamination is the base/build interface and often UAM component height and quality are limited by failure at the base/build interface. Low manufacturing temperatures and favorable orientation of typical interface defects in UAM make ultrasonic NDE an attractive candidate for online monitoring. Two approaches for in-situ NDE are discussed and the design of the monitoring system optimized so that the quality of UAM components is not affected by the addition of the NDE setup. Preliminary results from in-situ ultrasonic NDE indicate the potential to be utilized for online qualification, closed-loop control and offline certification of UAM components.

Blade system design studies volume II : preliminary blade designs and recommended test matrix.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Griffin, Dayton A.

2004-06-01

As part of the U.S. Department of Energy's Wind Partnerships for Advanced Component Technologies (WindPACT) program, Global Energy Concepts, LLC is performing a Blade System Design Study (BSDS) concerning innovations in materials, processes and structural configurations for application to wind turbine blades in the multi-megawatt range. The BSDS Volume I project report addresses issues and constraints identified to scaling conventional blade designs to the megawatt size range, and evaluated candidate materials, manufacturing and design innovations for overcoming and improving large blade economics. The current report (Volume II), presents additional discussion of materials and manufacturing issues for large blades, including amore » summary of current trends in commercial blade manufacturing. Specifications are then developed to guide the preliminary design of MW-scale blades. Using preliminary design calculations for a 3.0 MW blade, parametric analyses are performed to quantify the potential benefits in stiffness and decreased gravity loading by replacement of a baseline fiberglass spar with carbon-fiberglass hybrid material. Complete preliminary designs are then presented for 3.0 MW and 5.0 MW blades that incorporate fiberglass-to-carbon transitions at mid-span. Based on analysis of these designs, technical issues are identified and discussed. Finally, recommendations are made for composites testing under Part I1 of the BSDS, and the initial planned test matrix for that program is presented.« less

75 FR 37812 - Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-30

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort AGENCY: National Institute for Occupational Safety and Health... and Human Services (HHS) gives notice concerning the final effect of the HHS decision to designate a...

75 FR 27784 - Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-18

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort AGENCY: National Institute for Occupational Safety and Health... concerning the final effect of the decision to designate a class of employees from Westinghouse Electric Corp...

77 FR 15759 - Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-16

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort AGENCY: National Institute for Occupational Safety and Health...). ACTION: Notice. SUMMARY: HHS gives notice concerning the final effect of the HHS decision to designate a...

77 FR 60438 - Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-03

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort AGENCY: National Institute for Occupational Safety and Health...). ACTION: Notice. SUMMARY: HHS gives notice concerning the final effect of the HHS decision to designate a...

77 FR 60437 - Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-03

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort AGENCY: National Institute for Occupational Safety and Health...). ACTION: Notice. SUMMARY: HHS gives notice concerning the final effect of the HHS decision to designate a...

77 FR 69845 - Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-21

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort AGENCY: National Institute for Occupational Safety and Health...). ACTION: Notice. SUMMARY: HHS gives notice concerning the final effect of the HHS decision to designate a...

78 FR 70949 - Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-27

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort AGENCY: National Institute for Occupational Safety and Health...). ACTION: Notice. SUMMARY: HHS gives notice concerning the final effect of the HHS decision to designate a...

78 FR 21955 - Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-12

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort AGENCY: National Institute for Occupational Safety and Health...). ACTION: Notice. SUMMARY: HHS gives notice concerning the final effect of the HHS decision to designate a...

78 FR 21954 - Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-12

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort AGENCY: National Institute for Occupational Safety and Health...). ACTION: Notice. SUMMARY: HHS gives notice concerning the final effect of the HHS decision to designate a...

75 FR 27784 - Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-18

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort AGENCY: National Institute for Occupational Safety and Health... concerning the final effect of the decision to designate a class of employees from Lawrence Livermore...

75 FR 27784 - Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-18

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort AGENCY: National Institute for Occupational Safety and Health... concerning the final effect of the decision to designate a class of employees at the Lawrence Berkeley...

[The design of a nationwide cohort study in Germany : the pretest studies of the German National Cohort (GNC)].

PubMed

Ahrens, W; Greiser, H; Linseisen, J; Kluttig, A; Schipf, S; Schmidt, B; Günther, K

2014-11-01

The German National Cohort (GNC) is the largest population-based cohort study in Germany. Beginning in 2014, a total of 200,000 women and men aged 20-69 years will be examined in 18 study centers. The aim of the study is to investigate the etiology of chronic diseases in relation to lifestyle, genetic, socioeconomic, and environmental factors and to develop appropriate methods for early diagnosis and prevention of diseases such as cardiovascular and respiratory diseases, cancer, diabetes, neurodegenerative/psychiatric diseases, as well as musculoskeletal and infectious diseases. Pretest studies (phase 1 and 2) were conducted to select methods, instruments, and procedures for the main study, to develop standard operating procedures, and to design and test the examination program according to acceptance, expected duration, and feasibility. The pretest studies included testing of interviews, questionnaires, anthropometric measurements, several medical examinations, and the collection of biosamples. In addition, the logistic, technical, and personnel infrastructure for the main study could be established including the study centers, the central infrastructure for data management, processes to coordinate the study, and data protection and quality management concepts. The examination program for the main phase of the GNC was designed and optimized based on the results of the pretest studies. The GNC is a population-based, highly standardized and excellently phenotyped cohort that will be the basis for new strategies for risk assessment and identification, early diagnosis, and prevention of multifactorial diseases.

War and Well-Being: The Association between Forgiveness, Social Support, Posttraumatic Stress Disorder, and Well-Being during and after War.

PubMed

Weinberg, Michael; Harel, Hila; Shamani, Michal; Or-Chen, Keren; Ron, Pnina; Gil, Sharon

2017-10-01

Exposure to war can lead to numerous traumatic experiences affecting the daily lives and personal well-being of the civilian population. However, no research to date has examined the associations between postwar well-being and posttraumatic stress disorder (PTSD) symptoms, tendency to forgive, and social support during and following war. Authors examined a sample of 160 Israeli civilians who were exposed to rocket and missile fire during the 2014 Gaza War. Time 1 (Tl) started approximately one week after the beginning of the war and ended four weeks later following the first 72-hour ceasefire declaration by the United Nations. Respondents were re-approached by personal e-mail approximately one month after T1. A structural equation model design showed that higher postwar tendency to forgive, and social support, are associated with higher postwar well-being. It is notable that higher social support during the war had a negative effect on postwar well-being. In addition, higher posttraumatic symptoms and well-being during the war had a positive effect on higher postwar well-being. The study findings reinforce the importance of personal variables in postwar well-being. However, increased awareness of both social support and PTSD symptoms as "double-edged sword" resources is advisable, considering the different effects of social support and PTSD symptoms on well-being both during and after the war. © 2017 National Association of Social Workers.

Suppressing Nonradiative Recombination in Crown-Shaped Quantum Wells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Park, Kwangwook; Ju, Gunwu; Na, Byung Hoon

We examined the structural and optical properties of a crown-shaped quantum well (CSQW) to suppress nonradiative recombination. To reduce carrier loss in defect traps at the well/barrier interface, the CSQW was designed to concentrate carriers in the central region by tailoring the bandgap energy. Temperature-dependent photoluminescence measurements showed that the CSQW had a high activation energy and low potential fluctuation. In addition, the long carrier lifetime of the CSQW at high temperatures can be interpreted as indicating a decrease in carrier loss at defect traps.

Visual Design Principles: An Empirical Study of Design Lore

ERIC Educational Resources Information Center

Kimball, Miles A.

2013-01-01

Many books, designers, and design educators talk about visual design principles such as balance, contrast, and alignment, but with little consistency. This study uses empirical methods to explore the lore surrounding design principles. The study took the form of two stages: a quantitative literature review to determine what design principles are…

75 FR 27785 - Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-18

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort AGENCY: National Institute for Occupational Safety and Health... concerning the final effect of the decision to designate a class of employees from Area IV of the Santa...

75 FR 67364 - Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-02

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort AGENCY: National Institute for Occupational Safety and Health... concerning the final effect of the HHS decision to designate a class of employees from the Blockson Chemical...

76 FR 7852 - Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-11

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort AGENCY: National Institute for Occupational Safety and Health... concerning the final effect of the HHS decision to designate a class of employees from Texas City Chemicals...

76 FR 59701 - Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-27

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort AGENCY: National Institute for Occupational Safety and Health... concerning the final effect of the HHS decision to designate a class of employees from the Sandia National...

76 FR 7852 - Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-11

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort AGENCY: National Institute for Occupational Safety and Health... concerning the final effect of the HHS decision to designate a class of employees from Simonds Saw and Steel...

76 FR 7852 - Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-11

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort AGENCY: National Institute for Occupational Safety and Health... concerning the final effect of the HHS decision to designate a class of employees from BWX Technologies, Inc...

Resilience and well-being amongst seafarers: cross-sectional study of crew across 51 ships.

PubMed

Doyle, Niamh; MacLachlan, Malcolm; Fraser, Alistair; Stilz, Ralf; Lismont, Karlien; Cox, Henriette; McVeigh, Joanne

2016-02-01

Duration at sea was investigated as a potential chronic stressor amongst seafarers in addition to the mediating roles of previous seafaring experience and hardiness between duration and stress. In a cross-sectional design, questionnaires were emailed to 53 tanker vessels in an international shipping company with questions relating to duration at sea, perceived stress, personality hardiness and work characteristics. The sample comprised 387 seafarers (98% male) including ratings, crew, officers, engineers, and catering staff that had been on board their ship between 0 and 24 weeks. Duration at sea was unrelated to self-reported perceived stress, even after controlling for previous seafaring experience and hardiness. Additional regression analyses demonstrated that self-reported higher levels of resilience, longer seafaring experience and greater instrumental work support were significantly associated with lower levels of self-reported stress at sea. These results imply that at least for the first 24 weeks at sea, exposure to the seafaring environment did not act as a chronic stressor. The confined environment of a ship presents particular opportunities to introduce resilience and work support programmes to help seafarers manage and reduce stress, and to enhance their well-being at sea.

Design and analysis study of a spacecraft optical transceiver package

NASA Technical Reports Server (NTRS)

Lambert, S. G.

1985-01-01

A detailed system level design of an Optical Transceiver Package (OPTRANSPAC) for a deep space vehicle whose mission is outer planet exploration is developed. In addition to the terminal design, this study provides estimates of the dynamic environments to be encountered by the transceiver throughout its mission life. Optical communication link analysis, optical thin lens design, electronic functional design and mechanical layout and packaging are employed in the terminal design. Results of the study describe an Optical Transceiver Package capable of communicating to an Earth Orbiting Relay Station at a distance of 10 Astronomical Units (AU) and data rates up to 100 KBPS. The transceiver is also capable of receiving 1 KBPS of command data from the Earth Relay. The physical dimensions of the terminal are contained within a 3.5' x 1.5' x 2.0' envelope and the transceiver weight and power are estimated at 52.2 Kg (115 pounds) and 57 watts, respectively.

Learning environment and emotional well-being: A qualitative study of undergraduate nursing students.

PubMed

Tharani, Ambreen; Husain, Yusra; Warwick, Ian

2017-12-01

Students can experience multiple stressors during their academic life which have an impact on their emotional health and academic progress. This study sought to explore students' understanding of and factors affecting their emotional well-being in an undergraduate nursing programme at a private nursing institution in Karachi, Pakistan. In this qualitative study, data were collected through individual semi-structured interviews using a self-designed guide from 16 participants in total, drawn from various years of the selected undergraduate programme. Participants noted that the quality of the 'learning environment' was a key influence on their emotional well-being. They highlighted faculty role and teaching approaches, academic expectations and availability of learning resources as important factors that affected their emotional well-being as well as their academic performance. Institutional support was also deemed important. Factors associated with a 'hidden curriculum' were found to be a threat to students' emerging sense of professionalism. Suggestions are given as to how the learning environment in the nursing programme under study can be improved to take into account students' emotional well-being. Emphasis needs to be laid on developing supportive faculty role to provide conducive learning environment and professional development of students. Efforts to develop stress-free academic environment with supportive institutional policies need to be considered. Copyright © 2017 Elsevier Ltd. All rights reserved.

A traditional and a less-invasive robust design: choices in optimizing effort allocation for seabird population studies

USGS Publications Warehouse

Converse, S.J.; Kendall, W.L.; Doherty, P.F.; Naughton, M.B.; Hines, J.E.; Thomson, David L.; Cooch, Evan G.; Conroy, Michael J.

2009-01-01

the LIRD performed as well or nearly as well as certain variations of the RD in terms of root mean square error, especially when relatively little of the total effort was allocated to the assessment of the marked-to-unmarked ratio versus to initial captures. For the RD, we found no clear benefit of using 2, 4, or 6 secondary sampling occasions per year, though this result will depend on the relative effort costs of captures versus recaptures and on the length of the study. We also found that field-readable bands, which may be affixed to birds in addition to standard metal bands, will be beneficial in longer-term studies of albatrosses in the Northwestern Hawaiian Islands. Field-readable bands reduce the effort cost of recapturing individuals, and in the long-term this cost reduction can offset the additional effort expended in affixing the bands. Finally, our approach to determining optimal study design can be generally applied by researchers, with little seed data, to design their studies at the outset.

76 FR 68460 - Designation of a Class of Employees for Addition to the Special Exposure Cohort

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-04

... designate a class of employees from the Ames Laboratory at Iowa State University as an addition to the... contractors and subcontractors who worked in any area of the Ames Laboratory at Iowa State University [email protected] . John Howard, Director, National Institute for Occupational Safety and Health. [FR Doc. 2011...

10 CFR 60.132 - Additional design criteria for surface facilities in the geologic repository operations area.

Code of Federal Regulations, 2014 CFR

2014-01-01

... conversion to a form suitable for disposal at an alternative site in accordance with any regulations that are... 10 Energy 2 2014-01-01 2014-01-01 false Additional design criteria for surface facilities in the geologic repository operations area. 60.132 Section 60.132 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED...

10 CFR 60.132 - Additional design criteria for surface facilities in the geologic repository operations area.

Code of Federal Regulations, 2012 CFR

2012-01-01

... conversion to a form suitable for disposal at an alternative site in accordance with any regulations that are... 10 Energy 2 2012-01-01 2012-01-01 false Additional design criteria for surface facilities in the geologic repository operations area. 60.132 Section 60.132 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED...

10 CFR 60.132 - Additional design criteria for surface facilities in the geologic repository operations area.

Code of Federal Regulations, 2013 CFR

2013-01-01

... conversion to a form suitable for disposal at an alternative site in accordance with any regulations that are... 10 Energy 2 2013-01-01 2013-01-01 false Additional design criteria for surface facilities in the geologic repository operations area. 60.132 Section 60.132 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED...

10 CFR 60.132 - Additional design criteria for surface facilities in the geologic repository operations area.

Code of Federal Regulations, 2011 CFR

2011-01-01

... conversion to a form suitable for disposal at an alternative site in accordance with any regulations that are... 10 Energy 2 2011-01-01 2011-01-01 false Additional design criteria for surface facilities in the geologic repository operations area. 60.132 Section 60.132 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED...

Designing a Model of a Digital Ecosystem for Healthcare and Wellness Using the Business Model Canvas.

PubMed

León, María Cosio; Nieto-Hipólito, Juan Ivan; Garibaldi-Beltrán, Julián; Amaya-Parra, Guillermo; Luque-Morales, Priscy; Magaña-Espinoza, Pedro; Aguilar-Velazco, José

2016-06-01

Wellness is a term often used to talk about optimal health as "dynamic balance of physical, emotional, social, spiritual, and intellectual health." While healthcare is a term about care offered to patients for improving their health. We use both terms, as well as the Business Model Canvas (BMC) methodology, to design a digital ecosystem model for healthcare and wellness called DE4HW; the model considers economic, technological, and legal asymmetries, which are present on e-services beyond geographical regions. BMC methodology was embedded into the global project strategy called: IBOT (Initiate, Build, Operate and Transfer); it is a methodology to establish a functional, integrated national telemedicine network and virtual education network; of which we took its phases rationale. The results in this work illustrate the design of DE4HW model, into the first phase of IBOT, enriched with the BMC, which enables us to define actors, their interactions, rules and protocols, in order to build DE4HW, while IBOT strategy manages the project goal, up to the transfer phase, where an integral service platform of healthcare and wellness is turned over to stakeholders.

75 FR 27784 - Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-18

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Final Effect of Designation of a Class of Employees for Addition to the Special Exposure Cohort AGENCY: National Institute for Occupational Safety and Health... concerning the final effect of the decision to designate a class of employees from the Nevada Test Site as an...

Mechanistic Study of Electrolyte Additives to Stabilize High-Voltage Cathode-Electrolyte Interface in Lithium-Ion Batteries.

PubMed

Gao, Han; Maglia, Filippo; Lamp, Peter; Amine, Khalil; Chen, Zonghai

2017-12-27

Current developments of electrolyte additives to stabilize electrode-electrolyte interface in lithium-ion batteries highly rely on a trial-and-error search, which involves repetitive testing and intensive amount of resources. The lack of understandings on the fundamental protection mechanisms of the additives significantly increases the difficulty for the transformational development of new additives. In this study, we investigated two types of individual protection routes to build a robust cathode-electrolyte interphase at high potentials: (i) a direct reduction in the catalytic decomposition of the electrolyte solvent; and (ii) formation of a "corrosion inhibitor film" that prevents severely attack and passivation from protons that generated from the solvent oxidation, even the decomposition of solvent cannot be mitigated. Effect of two exemplary electrolyte additives, lithium difluoro(oxalato)borate (LiDFOB) and 3-hexylthiophene (3HT), on LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC 622) cathode were investigated to validate our hypothesis. It is demonstrated that understandings of both electrolyte additives and solvent are essential and careful balance between the cathode protection mechanism of additives and their side effects is critical to obtain optimum results. More importantly, this study opens up new directions of rational design of functional electrolyte additives for the next-generation high-energy-density lithium-ion chemistries.

A qualitative study of physicians' own wellness-promotion practices

PubMed Central

Weiner, Eric L; Swain, Geoffrey R; Wolf, Barbara; Gottlieb, Mark

2001-01-01

Objective To delineate the specific practices that physicians use to promote their own well-being. Design, setting, and participants 304 members of a primary care practice-based research group responded by mail to a survey on physician well-being. From the original survey, 130 subjects responded to an open-ended survey item regarding their own wellness-promotion practices. Methods Qualitative content analysis was used to identify the common themes in the physicians' responses to the open-ended question. A validated 18-item instrument, the Scales of Psychological Well-Being (SPWB), was used for measurement. Main outcome measures Similarities and differences between the various wellness-promotion practices that respondents reported using and associations between the use of these practices and SPWB scores. Results The 5 primary wellness-promotion practices that evolved from thematic analysis of the survey responses included “relationships,” “religion or spirituality,” “self-care,” “work,” and “approaches to life.” The use of the last type of practice was significantly associated with increased psychological well-being (SPWB) scores compared with the use of any of the other wellness-promotion practice categories (P<0.01), and there was a trend toward increased well-being among users of any category of wellness-promotion practices. Comments by our respondents provide specific descriptions of how physicians attend to their emotional, spiritual, and psychological well-being. Conclusion Physicians use a variety of approaches to promote their own well-being, which sort themselves into 5 main categories and appear to correlate with improved levels of psychological well-being among users. PMID:11154656

Effectiveness of integrated body-mind-spirit group intervention on the well-being of Indian patients with depression: a pilot study.

PubMed

Sreevani, Rentala; Reddemma, Konduru; Chan, Cecilia L W; Leung, Pamela Pui Yu; Wong, Venus; Chan, Celia Hoi Yan

2013-09-01

Depression is a leading cause of disability worldwide. There is a need to develop effective strategies to treat depression and prevent recurrence. Treatments that combine pharmacological and psychotherapeutic approaches are preferred for treating severe forms of depression. The study assesses the effect of an integrated body-mind-spirit group intervention in patients with depression. This pilot study was a pretest-posttest design study. Thirty adult patients diagnosed with depression attending the psychiatric outpatient department at a district hospital were randomly assigned to either the intervention group or comparison group. Each group had 15 patients. The intervention group received both the intervention and routine hospital treatment and underwent four group integrated body-mind-spirit group intervention therapy sessions. These sessions were held once per week on either Saturday or Sunday, with each session lasting more than 3 hours. Comparison group participants received routine hospital treatment only. Outcome measures, including level of depression, well-being, and work and social adjustment, were measured using the Beck Depression Inventory-II, body-mind-spirit well-being scale, and work and social adjustment scale. Both groups were evaluated at baseline, 1 month, 2 months, and 3 months. Results showed that both groups had significant reductions in the level of depression, improvements in well-being, and work and social adjustment at 3-month follow-up compared with baseline. In addition, the intervention group showed significant mean differences in levels of depression, well-being, and work and social adjustment compared with the comparison group. The integrated body-mind-spirit group intervention model appears to reduce depressive symptoms and improve well-being in patients with depression.

Tubular copper thrust chamber design study

NASA Technical Reports Server (NTRS)

Masters, A. I.; Galler, D. E.

1992-01-01

The use of copper tubular thrust chambers is particularly important in high performance expander cycle space engines. Tubular chambers have more surface area than flat wall chambers, and this extra surface area provides enhanced heat transfer for additional energy to power the cycle. This paper was divided into two sections: (1) a thermal analysis and sensitivity study; and (2) a preliminary design of a selected thrust chamber configuration. The thermal analysis consisted of a statistical optimization to determine the optimum tube geometry, tube booking, thrust chamber geometry, and cooling routing to achieve the maximum upper limit chamber pressure for a 25,000 pound thrust engine. The preliminary design effort produced a layout drawing of a tubular thrust chamber that is three inches shorter than the Advanced Expander Test Bed (AETB) milled channel chamber but is predicted to provide a five percent increase in heat transfer. Testing this chamber in the AETB would confirm the inherent advantages of tubular chamber construction and heat transfer.

Pre-post, mixed-methods feasibility study of the WorkingWell mobile support tool for individuals with serious mental illness in the USA: a pilot study protocol.

PubMed

Nicholson, Joanne; Wright, Spenser M; Carlisle, Alyssa M

2018-02-06

Successful competitive employment has been found to be related to enhanced self-esteem, higher quality of life and reduced mental health service use for individuals living with serious mental illnesses (SMIs) including schizophrenia, bipolar disorder and major depression. The effectiveness of the individual placement and support model has been demonstrated in multiple randomised controlled trials in many countries. The management of stress, depression and anxiety in the workplace may be effectively enhanced through digital mental health interventions. The WorkingWell mobile support tool ('app') is specifically designed to meet the need for illness management support for individuals with SMI in the workplace, as an adjunct to professional treatment. The WorkingWell app, grounded in evidence-based supported employment, is informed by user experience design. It will be tested in a pre-post design, mixed-methods pilot study to explore issues of feasibility, acceptability and usefulness, and to provide preliminary data on the impact of use. Putative mediators of improved job tenure and psychological well-being, including postintervention changes in social support, self-efficacy and work-related motivation, will be investigated. Forty individuals at least 18 years of age, meeting the eligibility requirements for supported employment services (ie, diagnosed with a mental illness meeting the criteria for severity, duration and treatment), working a minimum of 10 hours per week at study enrolment, and speaking, reading and writing in English will be recruited for the pilot study. Research staff will recruit individuals at community-based mental health agencies; provide orientation to the study, the study smartphones and the WorkingWell app; conduct research interviews including standardised measures as well as semistructured items; and provide technical assistance in telephone calls and inperson meetings. A sample of 10 agency staff will be recruited to obtain further

Development of a high-sensitivity BGO well counter for small animal PET studies.

PubMed

Yamamoto, Seiichi; Watabe, Hiroshi; Kanai, Yasukazu; Watabe, Tadashi; Imaizumi, Masao; Shimosegawa, Eku; Hatazawa, Jun

2012-01-01

In quantitative measurements of small animal PET studies, blood sampling is limited due to the small amounts of blood such animals can provide. In addition, injection doses are quite limited. In this situation, a high-sensitivity well counter would be useful for reducing the amount of the blood sample needed from small animals. Bismuth germinate (BGO) has a high stopping power for high-energy gamma rays compared to NaI(Tl), which is commonly used for conventional well counters. We have developed a BGO well counter and have tested it for blood-sampling measurements in small animals. The BGO well counter uses a square BGO block (59 × 59 × 50 mm) with a square open space (27 × 27 × 34 mm) in the center of the block. The BGO block was optically coupled to a 59-mm square-shaped photomultiplier tube (PMT). Signals from the PMT were digitally processed for the integration and energy window setting. The results showed that the energy spectrum of the BGO well counter measured with a Na-22 point source provided counts that were about 6 times higher for a 1022-keV (511 keV × 2) gamma peak than the spectrum of a 2-in. NaI(Tl) well counter. The relative sensitivity of the developed BGO well counter was 3.4 times higher than that of a NaI(Tl) well counter. The time activity curve of arterial blood was obtained successfully with the BGO well counter for a F-18-FDG study on rat. The BGO well counter will contribute to reducing the amount of sampled blood and to improving the throughput of quantitative measurements in small animal PET studies.

Advance Approach to Concept and Design Studies for Space Missions

NASA Technical Reports Server (NTRS)

Deutsch, M.; Nichols, J.

1999-01-01

Recent automated and advanced techniques developed at JPL have created a streamlined and fast-track approach to initial mission conceptualization and system architecture design, answering the need for rapid turnaround of trade studies for potential proposers, as well as mission and instrument study groups.

Study on Product Innovative Design Process Driven by Ideal Solution

NASA Astrophysics Data System (ADS)

Zhang, Fuying; Lu, Ximei; Wang, Ping; Liu, Hui

Product innovative design in companies today relies heavily on individual members’ experience and creative ideation as well as their skills of integrating creativity and innovation tools with design methods agilely. Creative ideation and inventive ideas generation are two crucial stages in product innovative design process. Ideal solution is the desire final ideas for given problem, and the striving reaching target for product design. In this paper, a product innovative design process driven by ideal solution is proposed. This design process encourages designers to overcome their psychological inertia, to foster creativity in a systematic way for acquiring breakthrough creative and innovative solutions in a reducing sphere of solution-seeking, and results in effective product innovative design rapidly. A case study example is also presented to illustrate the effectiveness of the proposed design process.

Using Set Model for Learning Addition of Integers

ERIC Educational Resources Information Center

Lestari, Umi Puji; Putri, Ratu Ilma Indra; Hartono, Yusuf

2015-01-01

This study aims to investigate how set model can help students' understanding of addition of integers in fourth grade. The study has been carried out to 23 students and a teacher of IVC SD Iba Palembang in January 2015. This study is a design research that also promotes PMRI as the underlying design context and activity. Results showed that the…

Optimized and Automated design of Plasma Diagnostics for Additive Manufacture

NASA Astrophysics Data System (ADS)

Stuber, James; Quinley, Morgan; Melnik, Paul; Sieck, Paul; Smith, Trevor; Chun, Katherine; Woodruff, Simon

2016-10-01

Despite having mature designs, diagnostics are usually custom designed for each experiment. Most of the design can be now be automated to reduce costs (engineering labor, and capital cost). We present results from scripted physics modeling and parametric engineering design for common optical and mechanical components found in many plasma diagnostics and outline the process for automated design optimization that employs scripts to communicate data from online forms through proprietary and open-source CAD and FE codes to provide a design that can be sent directly to a printer. As a demonstration of design automation, an optical beam dump, baffle and optical components are designed via an automated process and printed. Supported by DOE SBIR Grant DE-SC0011858.

Achieving Ships Mission Flexibility Through Designing, Printing And Operating Unmanned Systems With Additive Manufacturing And Delayed Differentiation

DTIC Science & Technology

2016-09-01

the UAV’s reliability in fulfilling the mission as well as the build- time of the UAV. 14. SUBJECT TERMS design , print and operate, DPO...previously. There are opportunities to work on the design of the UAV to reduce the cognitive workload of the service member and time required to “print” and...the need arises to tailor the UAV for the specific mission. The modification of an existing design is expected to take a much shorter time than the

Conceptual design studies of 1985 commercial VTOL transports that utilized rotors, Volume 1

NASA Technical Reports Server (NTRS)

Magee, J. P.; Clark, R. D.; Alexander, H. R.

1974-01-01

Results of conceptual design studies of commercial rotary wing transport aircraft for the 1985 time period are presented. Two aircraft configurations, a tandem helicopter and a tilt rotor, were designed for a 200 nautical mile short haul mission with an upper limit of 100 passengers. In addition to the baseline aircraft two further designs of each configuration are included to assess the impact of external noise design criteria on the aircraft size, weight, and cost.

Anthropometric Accommodation in Space Suit Design

NASA Technical Reports Server (NTRS)

Rajulu, Sudhakar; Thaxton, Sherry

2007-01-01

Design requirements for next generation hardware are in process at NASA. Anthropometry requirements are given in terms of minimum and maximum sizes for critical dimensions that hardware must accommodate. These dimensions drive vehicle design and suit design, and implicitly have an effect on crew selection and participation. At this stage in the process, stakeholders such as cockpit and suit designers were asked to provide lists of dimensions that will be critical for their design. In addition, they were asked to provide technically feasible minimum and maximum ranges for these dimensions. Using an adjusted 1988 Anthropometric Survey of U.S. Army (ANSUR) database to represent a future astronaut population, the accommodation ranges provided by the suit critical dimensions were calculated. This project involved participation from the Anthropometry and Biomechanics facility (ABF) as well as suit designers, with suit designers providing expertise about feasible hardware dimensions and the ABF providing accommodation analysis. The initial analysis provided the suit design team with the accommodation levels associated with the critical dimensions provided early in the study. Additional outcomes will include a comparison of principal components analysis as an alternate method for anthropometric analysis.

Informing Healthcare Waiting Area Design Using Transparency Attributes: A Comparative Preference Study.

PubMed

Jiang, Shan; Powers, Matthew; Allison, David; Vincent, Ellen

2017-07-01

This study aimed to explore people's visual preference for waiting areas in general hospital environments designed with transparency attributes that fully integrate nature. Waiting can be a tedious and frustrating experience among people seeking healthcare treatments and negatively affect their perception of the quality of care. Positive distractions and supportive designs have gained increasing attraction to improve people's waiting experience. Nature, which has shown therapeutic effects according to a growing amount of evidence, could be a distinguished positive distraction in waiting areas. Additionally, the theory of transparency was operationalized to indicate a spatial continuity between the external nature and the built interiors in general healthcare waiting area design. A survey method was adopted in the study. Twenty-one images of general healthcare waiting areas depicting three design typologies were preselected following a strict procedure, including designs with (a) no window views, (b) limited window views to nature, and (c) transparent spaces with maximum natural views. Ninety-five student participants rated the images based on their visual preference using a Likert-type scale. The results showed that transparent waiting areas were significantly preferred. A significant positive relationship existed between the level of transparency and people's preference scores. The factor analysis indicated additional supportive features that may affect people's preferences, including daylight, perceived warmth, noninstitutional furniture arrangement, visual orientation, and the use of natural materials for interior design. However, these tentative results need to be furthered tested with the real patient population as the next step of this study.

Understanding Interactions between Hydrogeologic Factors, Design Variables, and System Operations for Multi-Well Aquifer Storage and Recovery Systems

NASA Astrophysics Data System (ADS)

Majumdar, S.; Miller, G. R.; Smith, B.; Sheng, Z.

2017-12-01

Aquifer Storage and Recovery (ASR) system is a powerful tool for managing our present and future freshwater supplies. It involves injection of excess water into an aquifer, storing and later recovering it when needed, such as in a drought or during peak demand periods. Multi-well ASR systems, such as the Twin Oaks Facility in San Antonio, consist of a group of wells that are used for simultaneous injection and extraction of stored water. While significant research has gone into examining the effects of hydraulic and operational factors on recovery efficiency for single ASR well, little is known about how multi-well systems respond to these factors and how energy uses may vary. In this study, we created a synthetic ASR model in MODFLOW to test a range of multi-well scenarios. We altered design parameters (well spacing, pumping capacity, well configuration), hydrogeologic factors (regional hydraulic gradient, hydraulic conductivity, dispersivity), and operational variables (injection and withdrawal durations; pumping rates) to determine the response of the system across a realistic range of interrelated parameters. We then computed energy use for each simulation, based on the hydraulic head in each well and standard pump factors, as well as recovery efficiency, based on tracer concentration in recovered water from the wells. The tracer concentration in the groundwater was determined using MT3DMS. We observed that the recovery and energy efficiencies for the Multi-well ASR system decrease with the increase in well spacing and hydraulic gradient. When longitudinal dispersivity was doubled, the recovery and energy efficiencies were nearly halved. Another finding from our study suggests that we can recover nearly 90% of the water after two successive cycles of operation. The results will be used to develop generalized operational guidelines for meeting freshwater demands and also optimise the energy consumed during pumping.

Influence of study approaches and course design on academic success in the undergraduate anatomy laboratory.

PubMed

Eleazer, Courtney D; Scopa Kelso, Rebecca

2018-01-04

Many pre-health professional programs require completion of an undergraduate anatomy course with a laboratory component, yet grades in these courses are often low. Many students perceive anatomy as a more challenging subject than other coursework, and the resulting anxiety surrounding this perception may be a significant contributor to poor performance. Well-planned and deliberate guidance from instructors, as well as thoughtful course design, may be necessary to assist students in finding the best approach to studying for anatomy. This article assesses which study habits are associated with course success and whether course design influences study habits. Surveys (n = 1,274) were administered to students enrolled in three undergraduate human anatomy laboratory courses with varying levels of cooperative learning and structured guidance. The surveys collected information on potential predictors of performance, including student demographics, educational background, self-assessment ability, and study methods (e.g., flashcards, textbooks, diagrams). Compared to low performers, high performers perceive studying in laboratory, asking the instructor questions, quizzing alone, and quizzing others as more effective for learning. Additionally, students co-enrolled in a flipped, active lecture anatomy course achieve higher grades and find active learning activities (e.g., quizzing alone and in groups) more helpful for their learning in the laboratory. These results strengthen previous research suggesting that student performance is more greatly enhanced by an active classroom environment that practices successful study strategies rather than one that simply encourages students to employ such strategies inside and outside the classroom. Anat Sci Educ. © 2018 American Association of Anatomists. © 2018 American Association of Anatomists.

Neighborhood cohesion and daily well-being: Results from a diary study

PubMed Central

Robinette, Jennifer W.; Charles, Susan T.; Mogle, Jacqueline A.; Almeida, David M.

2013-01-01

Neighborly cohesiveness has documented benefits for health. Furthermore, high perceived neighborhood cohesion offsets the adverse health effects of neighborhood socioeconomic adversity. One potential way neighborhood cohesion influences health is through daily stress processes. The current study uses participants (n = 2022, age 30–84 years) from The Midlife in the United States II and the National Study of Daily Experiences II, collected between 2004–2006, to examine this hypothesis using a within-person, daily diary design. We predicted that people who perceive high neighborhood cohesion are exposed to fewer daily stressors, such as interpersonal arguments, lower daily physical symptoms and negative affect, and higher daily positive affect. We also hypothesized that perceptions of neighborhood cohesion buffer declines in affective and physical well-being on days when daily stressors do occur. Results indicate that higher perceived neighborhood cohesion predicts fewer self-reported daily stressors, higher positive affect, lower negative affect, and fewer physical health symptoms. High perceived neighborhood cohesion also buffers the effects of daily stressors on negative affect, even after adjusting for other sources of social support. Results from the present study suggest interventions focusing on neighborhood cohesion may result in improved well-being and may minimize the adverse effect of daily stressors. PMID:24034965

Miniaturized GPCR signaling studies in 1536-well format.

PubMed

Shultz, S; Worzella, T; Gallagher, A; Shieh, J; Goueli, S; Hsiao, K; Vidugiriene, J

2008-09-01

G protein-coupled receptors (GPCRs) are involved in various physiological processes, such as behavior changes, mood alteration, and regulation of immune-system activity. Thus, GPCRs are popular targets in drug screening, and a well-designed assay can speed up the discovery of novel drug candidates. The Promega cAMP-Glo Assay is a homogenous bioluminescent assay to monitor changes in intracellular cyclic adenosine monophosphate (cAMP) concentrations in response to the effect of an agonist, antagonist, or test compound on GPCRs. Together with the Labcyte Echo 555 acoustic liquid handler and the Deerac Fluidics Equator HTS reagent dispenser, this setup can screen compounds in 96-, 384-, and 1536-well formats for their effects on GPCRs. Here, we describe our optimization of the cAMP-Glo assay in 1536-well format, validate the pharmacology, and assess the assay robustness for HTS. We have successfully demonstrated the use of the assay in primary screening applications of known agonist and antagonist compounds, and confirmed the primary hits via secondary screening. Implementing a high-throughput miniaturized GPCR assay as demonstrated here allows effective screening for potential drug candidates.

Miniaturized GPCR Signaling Studies in 1536-Well Format

PubMed Central

Shultz, S.; Worzella, T.; Gallagher, A.; Shieh, J.; Goueli, S.; Hsiao, K.; Vidugiriene, J.

2008-01-01

G protein-coupled receptors (GPCRs) are involved in various physiological processes, such as behavior changes, mood alteration, and regulation of immune-system activity. Thus, GPCRs are popular targets in drug screening, and a well-designed assay can speed up the discovery of novel drug candidates. The Promega cAMP-Glo Assay is a homogenous bioluminescent assay to monitor changes in intracellular cyclic adenosine monophosphate (cAMP) concentrations in response to the effect of an agonist, antagonist, or test compound on GPCRs. Together with the Labcyte Echo 555 acoustic liquid handler and the Deerac Fluidics Equator HTS reagent dispenser, this setup can screen compounds in 96-, 384-, and 1536-well formats for their effects on GPCRs. Here, we describe our optimization of the cAMP-Glo assay in 1536-well format, validate the pharmacology, and assess the assay robustness for HTS. We have successfully demonstrated the use of the assay in primary screening applications of known agonist and antagonist compounds, and confirmed the primary hits via secondary screening. Implementing a high-throughput miniaturized GPCR assay as demonstrated here allows effective screening for potential drug candidates. PMID:19137117

A study on the applications of AI in finishing of additive manufacturing parts

NASA Astrophysics Data System (ADS)

Fathima Patham, K.

2017-06-01

Artificial intelligent and computer simulation are the technological powerful tools for solving complex problems in the manufacturing industries. Additive Manufacturing is one of the powerful manufacturing techniques that provide design flexibilities to the products. The products with complex shapes are directly manufactured without the need of any machining and tooling using Additive Manufacturing. However, the main drawback of the components produced using the Additive Manufacturing processes is the quality of the surfaces. This study aims to minimize the defects caused during Additive Manufacturing with the aid of Artificial Intelligence. The developed AI system has three layers, each layer is trying to eliminate or minimize the production errors. The first layer of the AI system optimizes the digitization of the 3D CAD model of the product and hence reduces the stair case errors. The second layer of the AI system optimizes the 3D printing machine parameters in order to eliminate the warping effect. The third layer of AI system helps to choose the surface finishing technique suitable for the printed component based on the Degree of Complexity of the product and the material. The efficiency of the developed AI system was examined on the functional parts such as gears.

Testing for Additivity in Chemical Mixtures Using a Fixed-Ratio Ray Design and Statistical Equivalence Testing Methods

EPA Science Inventory

Fixed-ratio ray designs have been used for detecting and characterizing interactions of large numbers of chemicals in combination. Single chemical dose-response data are used to predict an “additivity curve” along an environmentally relevant ray. A “mixture curve” is estimated fr...

Considerations of study design.

PubMed

Koretz, Ronald L

2007-12-01

Research projects attempt to answer specific questions. The particular study design that is selected will depend in large measure on the nature of the question and the time and resources available. There are 5 common categories of clinical questions; they relate to etiology, prognosis, utility of diagnostic tests, efficacy of proposed interventions, and cost of treatment in specific disease states. A number of study designs can be used. Case reports serve to memorialize unusual or novel aspects of diseases. Retrospective case series are useful for defining natural history. Case-control studies are used by epidemiologists to elucidate potential etiologies of diseases. Prospective cohort studies can be used to assess natural history or to assess potential disease etiologies. Controlled trials are designed to assess the efficacy of therapeutic interventions. Studies that define the sensitivity and specificity of diagnostic tests can be used to assess the utility of those tests. Economic analyses estimate the costs that particular diseases or therapies will require. Each of these study designs has limitations; with the exception of high-quality randomized trials, none of these study designs can establish a causative relationship between putative etiologic (or therapeutic) factors and disease (outcomes).

An Evaluation of Wellness Assessment Visualizations for Older Adults

PubMed Central

Reeder, Blaine; Yoo, Daisy; Aziz, Rafae; Thompson, Hilaire J.; Demiris, George

2015-01-01

Abstract Background Smart home technologies provide a valuable resource to unobtrusively monitor health and wellness within an older adult population. However, the breadth and density of data available along with aging associated decreases in working memory, prospective memory, spatial cognition, and processing speed can make it challenging to comprehend for older adults. We developed visualizations of smart home health data integrated into a framework of wellness. We evaluated the visualizations through focus groups with older adults and identified recommendations to guide the future development of visualizations. Materials and Methods We conducted four focus groups with older adult participants (n=31) at an independent retirement community. Participants were presented with three different visualizations from a wellness pilot study. A qualitative descriptive analysis was conducted to identify thematic content. Results We identified three themes related to processing and application of visualizations: (1) values of visualizations for wellness assessment, (2) cognitive processing approaches to visualizations, and (3) integration of health data for visualization. In addition, the focus groups highlighted key design considerations of visualizations important towards supporting decision-making and evaluation assessments within integrated health displays. Conclusions Participants found inherent value in having visualizations available to proactively engage with their healthcare provider. Integrating the visualizations into a wellness framework helped reduce the complexity of raw smart home data. There has been limited work on health visualizations from a consumer perspective, in particular for an older adult population. Creating appropriately designed visualizations is valuable towards promoting consumer involvement within the shared decision-making process of care. PMID:25401414

Oceanographic scanner system design study, volume 1

NASA Technical Reports Server (NTRS)

1971-01-01

The design is reported of a dual mode multispectral scanner, capable of satisfying both overland and oceanographic requirements. A complete system description and performance summary of the scanner are given. In addition, subsystem and component descriptions and performance analyses are treated in individual sections. The design of the scanner, with minimum modifications, interfaces to the ERTS spacecraft and the ground data handling system.

Addition of fraction in swimming context

NASA Astrophysics Data System (ADS)

Putri, R. I. I.; Gunawan, M. S.; Zulkardi

2017-12-01

This study aimed to produce learning trajectory that can help students in learning fractions by using swimming context. The study involved 37 fourth grade students with different capabilities in Elementary School IBA, South Sumatra, Indonesia. This study used an instructional theory called Indonesian version of Realistic Mathematics Education (PMRI). This research used design research method with three stages: preliminary design, the design experiment, and retrospective analysis. Several techniques used for collecting data including a video recording of students interaction in the group discussion, students’ work, and interviewing the students. To conclude, the swimming context could stimulate students’ informal knowledge about the meaning of fractions in which it can be used in the additional learning either the same denominator or different denominator.

Extracellular matrix protein in calcified endoskeleton: a potential additive for crystal growth and design

NASA Astrophysics Data System (ADS)

Azizur Rahman, M.; Fujimura, Hiroyuki; Shinjo, Ryuichi; Oomori, Tamotsu

2011-06-01

In this study, we demonstrate a key function of extracellular matrix proteins (ECMPs) on seed crystals, which are isolated from calcified endoskeletons of soft coral and contain only CaCO 3 without any living cells. This is the first report that an ECMP protein extracted from a marine organism could potentially influence in modifying the surface of a substrate for designing materials via crystallization. We previously studied with the ECMPs from a different type of soft coral ( Sinularia polydactyla) without introducing any seed crystals in the process , which showed different results. Thus, crystallization on the seed in the presence of ECMPs of present species is an important first step toward linking function to individual proteins from soft coral. For understanding this interesting phenomenon, in vitro crystallization was initiated in a supersaturated solution on seed particles of calcite (1 0 4) with and without ECMPs. No change in the crystal growth shape occurred without ECMPs present during the crystallization process. However, with ECMPs, the morphology and phase of the crystals in the crystallization process changed dramatically. Upon completion of crystallization with ECMPs, an attractive crystal morphology was found. Scanning electron microscopy (SEM) was utilized to observe the crystal morphologies on the seeds surface. The mineral phases of crystals nucleated by ECMPs on the seeds surface were examined by Raman spectroscopy. Although 50 mM Mg 2+ is influential in making aragonite in the crystallization process, the ECMPs significantly made calcite crystals even when 50 mM Mg 2+ was present in the process. Crystallization with the ECMP additive seems to be a technically attractive strategy to generate assembled micro crystals that could be used in crystals growth and design in the Pharmaceutical and biotechnology industries.

Mechanistic Study of Electrolyte Additives to Stabilize High-Voltage Cathode–Electrolyte Interface in Lithium-Ion Batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gao, Han; Maglia, Filippo; Lamp, Peter

Current developments of electrolyte additives to stabilize electrode-electrolyte interface in Li-ion batteries highly rely on a trial-and-error search, which involves repetitive testing and intensive amount of resources. The lack of understandings on the fundamental protection mechanisms of the additives significantly increases the difficulty for the transformational development of new additives. In this study, we investigated two types of individual protection routes to build a robust cathode-electrolyte interphase at high potentials: (i) a direct reduction in the catalytic decomposition of the electrolyte solvent; and (ii) formation of a “corrosion inhibitor film” that prevents severely attack and passivation from protons that generatedmore » from the solvent oxidation, even the decomposition of solvent cannot not mitigated. Effect of three exemplary electrolyte additives: (i) lithium difluoro(oxalato)borate (LiDFOB); (ii) 3-hexylthiophene (3HT); and (iii) tris(hexafluoro-iso-propyl)phosphate (HFiP), on LiNi0.6Mn0.2Co0.2O2 (NMC 622) cathode were investigated to validate our hypothesis. It is demonstrated that understandings of both electrolyte additives and solvent are essential and careful balance between the cathode protection mechanism of additives and their side effects is critical to obtain optimum results. More importantly, this study opens up new directions of rational design of functional electrolyte additives for the next generation high-energy density lithium-ion chemistries.« less

Use of single-well simulators and economic performance criteria to optimize fracturing treatment design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anderson, R.W.; Phillips, A.M.

1990-02-01

Low-permeability reservoirs are currently being propped with sand, resin-coated sand, intermediate-density proppants, and bauxite. This wide range of proppant cost and performance has resulted in the proliferation of proppant selection models. Initially, a rather vague relationship between well depth and proppant strength dictated the choice of proppant. More recently, computerized models of varying complexity that use net-present-value (NPV) calculations have become available. The input is based on the operator's performance goals for each well and specific reservoir properties. Simpler, noncomputerized approaches include cost/performance comparisons and nomographs. Each type of model, including several of the computerized models, is examined here. Bymore » use of these models and NPV calculations, optimum fracturing treatment designs have been developed for such low-permeability reservoirs as the Prue in Oklahoma. Typical well conditions are used in each of the selection models, and the results are compared.« less

On Becoming a Civic-Minded Instructional Designer: An Ethnographic Study of an Instructional Design Experience

ERIC Educational Resources Information Center

Yusop, Farrah Dina; Correia, Ana-Paula

2014-01-01

This ethnographic study took place in a graduate course at a large research university in the Midwestern United States. It presents an in-depth examination of the experiences and challenges of a group of four students learning to be Instructional Design and Technology professionals who are concerned with the well-being of all members of a society,…

The Netherlands Epidemiology of Obesity (NEO) study: study design and data collection.

PubMed

de Mutsert, Renée; den Heijer, Martin; Rabelink, Ton Johannes; Smit, Johannes Willem Adriaan; Romijn, Johannes Anthonius; Jukema, Johan Wouter; de Roos, Albert; Cobbaert, Christa Maria; Kloppenburg, Margreet; le Cessie, Saskia; Middeldorp, Saskia; Rosendaal, Frits Richard

2013-06-01

Obesity is a well-established risk factor for many chronic diseases. Incomplete insight exists in the causal pathways responsible for obesity-related disorders and consequently, in the identification of obese individuals at risk of these disorders. The Netherlands Epidemiology of Obesity (NEO) study is designed for extensive phenotyping to investigate pathways that lead to obesity-related diseases. The NEO study is a population-based, prospective cohort study that includes 6,673 individuals aged 45-65 years, with an oversampling of individuals with overweight or obesity. At baseline, data on demography, lifestyle, and medical history have been collected by questionnaires. In addition, samples of 24-h urine, fasting and postprandial blood plasma and serum, and DNA were collected. Participants underwent an extensive physical examination, including anthropometry, electrocardiography, spirometry, and measurement of the carotid artery intima-media thickness by ultrasonography. In random subsamples of participants, magnetic resonance imaging of abdominal fat, pulse wave velocity of the aorta, heart, and brain, magnetic resonance spectroscopy of the liver, indirect calorimetry, dual-energy X-ray absorptiometry, or accelerometry measurements were performed. The collection of data started in September 2008 and completed at the end of September 2012. Participants are followed for the incidence of obesity-related diseases and mortality. The NEO study investigates pathways that lead to obesity-related diseases. A better understanding of the mechanisms underlying the development of disease in obesity may help to identify individuals who are susceptible to the detrimental metabolic, cardiovascular and other consequences of obesity and has implications for the development of prevention and treatment strategies.

Monitoring system for the quality assessment in additive manufacturing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carl, Volker, E-mail: carl@t-zfp.de

Additive Manufacturing (AM) refers to a process by which a set of digital data -representing a certain complex 3dim design - is used to grow the respective 3dim real structure equal to the corresponding design. For the powder-based EOS manufacturing process a variety of plastic and metal materials can be used. Thereby, AM is in many aspects a very powerful tool as it can help to overcome particular limitations in conventional manufacturing. AM enables more freedom of design, complex, hollow and/or lightweight structures as well as product individualisation and functional integration. As such it is a promising approach with respectmore » to the future design and manufacturing of complex 3dim structures. On the other hand, it certainly calls for new methods and standards in view of quality assessment. In particular, when utilizing AM for the design of complex parts used in aviation and aerospace technologies, appropriate monitoring systems are mandatory. In this respect, recently, sustainable progress has been accomplished by joining the common efforts and concerns of a manufacturer Additive Manufacturing systems and respective materials (EOS), along with those of an operator of such systems (MTU Aero Engines) and experienced application engineers (Carl Metrology), using decent know how in the field of optical and infrared methods regarding non-destructive-examination (NDE). The newly developed technology is best described by a high-resolution layer by layer inspection technique, which allows for a 3D tomography-analysis of the complex part at any time during the manufacturing process. Thereby, inspection costs are kept rather low by using smart image-processing methods as well as CMOS sensors instead of infrared detectors. Moreover, results from conventional physical metallurgy may easily be correlated with the predictive results of the monitoring system which not only allows for improvements of the AM monitoring system, but finally leads to an optimisation of the

Monitoring system for the quality assessment in additive manufacturing

NASA Astrophysics Data System (ADS)

Carl, Volker

2015-03-01

Additive Manufacturing (AM) refers to a process by which a set of digital data -representing a certain complex 3dim design - is used to grow the respective 3dim real structure equal to the corresponding design. For the powder-based EOS manufacturing process a variety of plastic and metal materials can be used. Thereby, AM is in many aspects a very powerful tool as it can help to overcome particular limitations in conventional manufacturing. AM enables more freedom of design, complex, hollow and/or lightweight structures as well as product individualisation and functional integration. As such it is a promising approach with respect to the future design and manufacturing of complex 3dim structures. On the other hand, it certainly calls for new methods and standards in view of quality assessment. In particular, when utilizing AM for the design of complex parts used in aviation and aerospace technologies, appropriate monitoring systems are mandatory. In this respect, recently, sustainable progress has been accomplished by joining the common efforts and concerns of a manufacturer Additive Manufacturing systems and respective materials (EOS), along with those of an operator of such systems (MTU Aero Engines) and experienced application engineers (Carl Metrology), using decent know how in the field of optical and infrared methods regarding non-destructive-examination (NDE). The newly developed technology is best described by a high-resolution layer by layer inspection technique, which allows for a 3D tomography-analysis of the complex part at any time during the manufacturing process. Thereby, inspection costs are kept rather low by using smart image-processing methods as well as CMOS sensors instead of infrared detectors. Moreover, results from conventional physical metallurgy may easily be correlated with the predictive results of the monitoring system which not only allows for improvements of the AM monitoring system, but finally leads to an optimisation of the quality

Study and design of cryogenic propellant acquisition systems. Volume 1: Design studies

NASA Technical Reports Server (NTRS)

Burge, G. W.; Blackmon, J. B.

1973-01-01

An in-depth study and selection of practical propellant surface tension acquisition system designs for two specific future cryogenic space vehicles, an advanced cryogenic space shuttle auxiliary propulsion system and an advanced space propulsion module is reported. A supporting laboratory scale experimental program was also conducted to provide design information critical to concept finalization and selection. Designs using localized pressure isolated surface tension screen devices were selected for each application and preliminary designs were generated. Based on these designs, large scale acquisition prototype hardware was designed and fabricated to be compatible with available NASA-MSFC feed system hardware.

Designing, Prototyping and Evaluating Digital Mindfulness Applications: A Case Study of Mindful Breathing for Stress Reduction

PubMed Central

Hedman, Anders; Feng, Shuo; Li, Haibo; Osika, Walter

2017-01-01

Background During the past decade, there has been a rapid increase of interactive apps designed for health and well-being. Yet, little research has been published on developing frameworks for design and evaluation of digital mindfulness facilitating technologies. Moreover, many existing digital mindfulness applications are purely software based. There is room for further exploration and assessment of designs that make more use of physical qualities of artifacts. Objective The study aimed to develop and test a new physical digital mindfulness prototype designed for stress reduction. Methods In this case study, we designed, developed, and evaluated HU, a physical digital mindfulness prototype designed for stress reduction. In the first phase, we used vapor and light to support mindful breathing and invited 25 participants through snowball sampling to test HU. In the second phase, we added sonification. We deployed a package of probes such as photos, diaries, and cards to collect data from users who explored HU in their homes. Thereafter, we evaluated our installation using both self-assessed stress levels and heart rate (HR) and heart rate variability (HRV) measures in a pilot study, in order to measure stress resilience effects. After the experiment, we performed a semistructured interview to reflect on HU and investigate the design of digital mindfulness apps for stress reduction. Results The results of the first phase showed that 22 of 25 participants (88%) claimed vapor and light could be effective ways of promoting mindful breathing. Vapor could potentially support mindful breathing better than light (especially for mindfulness beginners). In addition, a majority of the participants mentioned sound as an alternative medium. In the second phase, we found that participants thought that HU could work well for stress reduction. We compared the effect of silent HU (using light and vapor without sound) and sonified HU on 5 participants. Subjective stress levels were

Design of the SHAPE-2 study: the effect of physical activity, in addition to weight loss, on biomarkers of postmenopausal breast cancer risk.

PubMed

van Gemert, Willemijn A M; Iestra, Jolein I; Schuit, Albertine J; May, Anne M; Takken, Tim; Veldhuis, Wouter B; van der Palen, Job; Wittink, Harriët; Peeters, Petra H M; Monninkhof, Evelyn M

2013-08-23

Physical inactivity and overweight are two known risk factors for postmenopausal breast cancer. Former exercise intervention studies showed that physical activity influences sex hormone levels, known to be related to postmenopausal breast cancer, mainly when concordant loss of body weight was achieved. The question remains whether there is an additional beneficial effect of physical activity when weight loss is reached. The SHAPE-2 study is a three-armed, multicentre trial. 243 sedentary, postmenopausal women who are overweight or obese (BMI 25-35 kg/m2) are enrolled. After a 4-6 week run-in period, wherein a baseline diet is prescribed, women are randomly allocated to (1) a diet group, (2) an exercise group or (3) a control group. The aim of both intervention groups is to lose an amount of 5-6 kg body weight in 10-14 weeks. The diet group follows an energy restricted diet and maintains the habitual physical activity level. The exercise group participates in a 16-week endurance and strength training programme of 4 hours per week. Furthermore, they are prescribed a moderate caloric restriction. The control group is asked to maintain body weight and continue the run-in baseline diet. This study will give insight in the potential attributable effect of physical activity on breast cancer risk biomarkers and whether this effect is mediated by changes in body composition, in postmenopausal women. Eventually this may lead to the design of specific lifestyle guidelines for prevention of breast cancer. The SHAPE-2 study is registered in the register of clinicaltrials.gov, Identifier: NCT01511276.

Parameters and pitfalls to consider in the conduct of food additive research, Carrageenan as a case study.

PubMed

Weiner, Myra L

2016-01-01

This paper provides guidance on the conduct of new in vivo and in vitro studies on high molecular weight food additives, with carrageenan, the widely used food additive, as a case study. It is important to understand the physical/chemical properties and to verify the identity/purity, molecular weight and homogeneity/stability of the additive in the vehicle for oral delivery. The strong binding of CGN to protein in rodent chow or infant formula results in no gastrointestinal tract exposure to free CGN. It is recommended that doses of high Mw non-caloric, non-nutritive additives not exceed 5% by weight of total solid diet to avoid potential nutritional effects. Addition of some high Mw additives at high concentrations to liquid nutritional supplements increases viscosity and may affect palatability, caloric intake and body weight gain. In in vitro studies, the use of well-characterized, relevant cell types and the appropriate composition of the culture media are necessary for proper conduct and interpretation. CGN is bound to media protein and not freely accessible to cells in vitro. Interpretation of new studies on food additives should consider the interaction of food additives with the vehicle components and the appropriateness of the animal or cell model and dose-response. Copyright © 2015 FMC Corporation. Published by Elsevier Ltd.. All rights reserved.

40 CFR 79.31 - Additives.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Additives. 79.31 Section 79.31... OF FUELS AND FUEL ADDITIVES Designation of Fuels and Additives § 79.31 Additives. (a) All additives... persons or property on a street or highway. For purposes of this registration, however, additives...

40 CFR 79.31 - Additives.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 17 2013-07-01 2013-07-01 false Additives. 79.31 Section 79.31... OF FUELS AND FUEL ADDITIVES Designation of Fuels and Additives § 79.31 Additives. (a) All additives... persons or property on a street or highway. For purposes of this registration, however, additives...

40 CFR 79.31 - Additives.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 17 2012-07-01 2012-07-01 false Additives. 79.31 Section 79.31... OF FUELS AND FUEL ADDITIVES Designation of Fuels and Additives § 79.31 Additives. (a) All additives... persons or property on a street or highway. For purposes of this registration, however, additives...

40 CFR 79.31 - Additives.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 17 2014-07-01 2014-07-01 false Additives. 79.31 Section 79.31... OF FUELS AND FUEL ADDITIVES Designation of Fuels and Additives § 79.31 Additives. (a) All additives... persons or property on a street or highway. For purposes of this registration, however, additives...

40 CFR 79.31 - Additives.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 16 2011-07-01 2011-07-01 false Additives. 79.31 Section 79.31... OF FUELS AND FUEL ADDITIVES Designation of Fuels and Additives § 79.31 Additives. (a) All additives... persons or property on a street or highway. For purposes of this registration, however, additives...

Study design requirements for RNA sequencing-based breast cancer diagnostics.

PubMed

Mer, Arvind Singh; Klevebring, Daniel; Grönberg, Henrik; Rantalainen, Mattias

2016-02-01

Sequencing-based molecular characterization of tumors provides information required for individualized cancer treatment. There are well-defined molecular subtypes of breast cancer that provide improved prognostication compared to routine biomarkers. However, molecular subtyping is not yet implemented in routine breast cancer care. Clinical translation is dependent on subtype prediction models providing high sensitivity and specificity. In this study we evaluate sample size and RNA-sequencing read requirements for breast cancer subtyping to facilitate rational design of translational studies. We applied subsampling to ascertain the effect of training sample size and the number of RNA sequencing reads on classification accuracy of molecular subtype and routine biomarker prediction models (unsupervised and supervised). Subtype classification accuracy improved with increasing sample size up to N = 750 (accuracy = 0.93), although with a modest improvement beyond N = 350 (accuracy = 0.92). Prediction of routine biomarkers achieved accuracy of 0.94 (ER) and 0.92 (Her2) at N = 200. Subtype classification improved with RNA-sequencing library size up to 5 million reads. Development of molecular subtyping models for cancer diagnostics requires well-designed studies. Sample size and the number of RNA sequencing reads directly influence accuracy of molecular subtyping. Results in this study provide key information for rational design of translational studies aiming to bring sequencing-based diagnostics to the clinic.

NASA transmission research and its probable effects on helicopter transmission design

NASA Technical Reports Server (NTRS)

Zaretsky, E. V.; Coy, J. J.; Townsend, D. P.

1983-01-01

Transmissions studied for application to helicopters in addition to the more conventional geared transmissions include hybrid (traction/gear), bearingless planetary, and split torque transmissions. Research is being performed to establish the validity of analysis and computer codes developed to predict the performance, efficiency, life, and reliability of these transmissions. Results of this research should provide the transmission designer with analytical tools to design for minimum weight and noise with maximum life and efficiency. In addition, the advantages and limitations of drive systems as well as the more conventional systems will be defined.

NASA transmission research and its probable effects on helicopter transmission design

NASA Technical Reports Server (NTRS)

Zaretsky, E. V.; Coy, J. J.; Townsend, D. P.

1984-01-01

Transmissions studied for application to helicopters in addition to the more conventional geared transmissions include hybrid (traction/gear), bearingless planetary, and split torque transmissions. Research is being performed to establish the validity of analysis and computer codes developed to predict the performance, efficiency, life, and reliability of these transmissions. Results of this research should provide the transmission designer with analytical tools to design for minimum weight and noise with maximum life and efficiency. In addition, the advantages and limitations of drive systems as well as the more conventional systems will be defined.

76 FR 14812 - Additional Air Quality Designations for the 2006 24-Hour Fine Particle National Ambient Air...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-18

... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Part 81 [EPA-HQ-OAR-2007-0562; EPA-HQ-OAR-2010-0163; FRL-9261-3] RIN-2060-AQ30 Additional Air Quality Designations for the 2006 24-Hour Fine Particle National... Particles National Ambient Air Quality Standards Correction In rule document 2011-2269 appearing on pages...

Additive manufacturing of materials: Opportunities and challenges

DOE Office of Scientific and Technical Information (OSTI.GOV)

Babu, Sudarsanam Suresh; Love, Lonnie J.; Dehoff, Ryan R.

Additive manufacturing (also known as 3D printing) is considered a disruptive technology for producing components with topologically optimized complex geometries as well as functionalities that are not achievable by traditional methods. The realization of the full potential of 3D printing is stifled by a lack of computational design tools, generic material feedstocks, techniques for monitoring thermomechanical processes under in situ conditions, and especially methods for minimizing anisotropic static and dynamic properties brought about by microstructural heterogeneity. In this paper, we discuss the role of interdisciplinary research involving robotics and automation, process control, multiscale characterization of microstructure and properties, and high-performancemore » computational tools to address each of these challenges. In addition, emerging pathways to scale up additive manufacturing of structural materials to large sizes (>1 m) and higher productivities (5–20 kg/h) while maintaining mechanical performance and geometrical flexibility are also discussed.« less

Additive manufacturing of materials: Opportunities and challenges

DOE PAGES

Babu, Sudarsanam Suresh; Love, Lonnie J.; Dehoff, Ryan R.; ...

2015-11-01

Additive manufacturing (also known as 3D printing) is considered a disruptive technology for producing components with topologically optimized complex geometries as well as functionalities that are not achievable by traditional methods. The realization of the full potential of 3D printing is stifled by a lack of computational design tools, generic material feedstocks, techniques for monitoring thermomechanical processes under in situ conditions, and especially methods for minimizing anisotropic static and dynamic properties brought about by microstructural heterogeneity. In this paper, we discuss the role of interdisciplinary research involving robotics and automation, process control, multiscale characterization of microstructure and properties, and high-performancemore » computational tools to address each of these challenges. In addition, emerging pathways to scale up additive manufacturing of structural materials to large sizes (>1 m) and higher productivities (5–20 kg/h) while maintaining mechanical performance and geometrical flexibility are also discussed.« less

Design of a mechanical system in gait rehabilitation with progressive addition of weight

NASA Astrophysics Data System (ADS)

Braidot, Ariel A. A.; Aleman, Guillermo L.

2011-12-01

In this paper we designed and developed a mechanical device for gait rehabilitation based on the application of "partial body weight reduction therapy". An evaluation of the characteristics of devices based on this therapy currently available on the market was carried out obtaining information of the different mechanisms used in it. The device was designed to adapt to different height and weight of patients and to be used with additional equipment in gait rehabilitation, for example, treadmills, elliptical trainers and vertical scalers. It was envisaged to be used by patients with asymmetry in the lower extremities capabilities. We developed a stable structure in steel ASTM A36 which does not depend on the building conditions of the installation site. RamAdvanse software was used to calculate structural stability. A winch with automatic brake mechanism was used to raise/lower the patient, who was tied to a comfortable harness which provided safety to the patient and therapist. It was possible to quantify precisely, using counterweights, the weight borne by the patient during therapy. We obtained a small-sized and ergonomic low-cost prototype, with similar features to those currently considered cutting-edge devices.

Partial gravity habitat study: With application to lunar base design

NASA Technical Reports Server (NTRS)

Capps, Stephen; Lorandos, Jason; Akhidime, Eval; Bunch, Michael; Lund, Denise; Moore, Nathan; Murakawa, Kio; Bell, Larry; Trotti, Guillermo; Neubek, Deb

1989-01-01

Comprehensive design requirements associated with designing habitats for humans in a partial gravity environment were investigated and then applied to a lunar base design. Other potential sites for application include planetary surfaces such as Mars, variable gravity research facilities, or a rotating spacecraft. Design requirements for partial gravity environments include: (1) locomotion changes in less than normal Earth gravity; (2) facility design issues, such as interior configuration, module diameter and geometry; and (3) volumetric requirements based on the previous as well as psychological issues involved in prolonged isolation. For application to a Lunar Base, it was necessary to study the exterior architecture and configuration to insure optimum circulation patterns while providing dual egress. Radiation protection issues were addressed to provide a safe and healthy environment for the crew, and finally, the overall site was studied to locate all associated facilities in context with the habitat. Mission planning was not the purpose of this study; therefore, a Lockheed scenario was used as an outline for the Lunar Base application, which was then modified to meet the project needs.

Using routine health information systems for well-designed health evaluations in low- and middle-income countries

PubMed Central

Wagenaar, Bradley H; Sherr, Kenneth; Fernandes, Quinhas; Wagenaar, Alexander C

2016-01-01

Routine health information systems (RHISs) are in place in nearly every country and provide routinely collected full-coverage records on all levels of health system service delivery. However, these rich sources of data are regularly overlooked for evaluating causal effects of health programmes due to concerns regarding completeness, timeliness, representativeness and accuracy. Using Mozambique’s national RHIS (Módulo Básico) as an illustrative example, we urge renewed attention to the use of RHIS data for health evaluations. Interventions to improve data quality exist and have been tested in low-and middle-income countries (LMICs). Intrinsic features of RHIS data (numerous repeated observations over extended periods of time, full coverage of health facilities, and numerous real-time indicators of service coverage and utilization) provide for very robust quasi-experimental designs, such as controlled interrupted time-series (cITS), which are not possible with intermittent community sample surveys. In addition, cITS analyses are well suited for continuously evolving development contexts in LMICs by: (1) allowing for measurement and controlling for trends and other patterns before, during and after intervention implementation; (2) facilitating the use of numerous simultaneous control groups and non-equivalent dependent variables at multiple nested levels to increase validity and strength of causal inference; and (3) allowing the integration of continuous ‘effective dose received’ implementation measures. With expanded use of RHIS data for the evaluation of health programmes, investments in data systems, health worker interest in and utilization of RHIS data, as well as data quality will further increase over time. Because RHIS data are ministry-owned and operated, relying upon these data will contribute to sustainable national capacity over time. PMID:25887561

Innovative tools for quality assessment: integrated quality criteria for review of multiple study designs (ICROMS).

PubMed

Zingg, W; Castro-Sanchez, E; Secci, F V; Edwards, R; Drumright, L N; Sevdalis, N; Holmes, A H

2016-04-01

With the aim to facilitate a more comprehensive review process in public health including patient safety, we established a tool that we have termed ICROMS (Integrated quality Criteria for the Review Of Multiple Study designs), which unifies, integrates and refines current quality criteria for a large range of study designs including qualitative research. Review, pilot testing and expert consensus. The tool is the result of an iterative four phase process over two years: 1) gathering of established criteria for assessing controlled, non-controlled and qualitative study designs; 2) pilot testing of a first version in two systematic reviews on behavioural change in infection prevention and control and in antibiotic prescribing; 3) further refinement and adding of additional study designs in the context of the European Centre for Disease Prevention and Control funded project 'Systematic review and evidence-based guidance on organisation of hospital infection control programmes' (SIGHT); 4) scrutiny by the pan-European expert panel of the SIGHT project, which had the objective of ensuring robustness of the systematic review. ICROMS includes established quality criteria for randomised studies, controlled before-and-after studies and interrupted time series, and incorporates criteria for non-controlled before-and-after studies, cohort studies and qualitative studies. The tool consists of two parts: 1) a list of quality criteria specific for each study design, as well as criteria applicable across all study designs by using a scoring system; 2) a 'decision matrix', which specifies the robustness of the study by identifying minimum requirements according to the study type and the relevance of the study to the review question. The decision matrix directly determines inclusion or exclusion of a study in the review. ICROMS was applied to a series of systematic reviews to test its feasibility and usefulness in the appraisal of multiple study designs. The tool was applicable

Mitigating cold flow problems of biodiesel: Strategies with additives

NASA Astrophysics Data System (ADS)

Mohanan, Athira

The present thesis explores the cold flow properties of biodiesel and the effect of vegetable oil derived compounds on the crystallization path as well as the mechanisms at play at different stages and length scales. Model systems including triacylglycerol (TAG) oils and their derivatives, and a polymer were tested with biodiesel. The goal was to acquire the fundamental knowledge that would help design cold flow improver (CFI) additives that would address effectively and simultaneously the flow problems of biodiesel, particularly the cloud point (CP) and pour point (PP). The compounds were revealed to be fundamentally vegetable oil crystallization modifiers (VOCM) and the polymer was confirmed to be a pour point depressant (PPD). The results obtained with the VOCMs indicate that two cis-unsaturated moieties combined with a trans-/saturated fatty acid is a critical structural architecture for depressing the crystallization onset by a mechanism wherein while the straight chain promotes a first packing with the linear saturated FAMEs, the kinked moieties prevent further crystallization. The study of model binary systems made of a VOCM and a saturated FAME with DSC, XRD and PLM provided a complete phase diagram including the thermal transformation lines, crystal structure and microstructure that impact the phase composition along the different crystallization stages, and elicited the competing effects of molecular mass, chain length mismatch and isomerism. The liquid-solid boundary is discussed in light of a simple thermodynamic model based on the Hildebrand equation and pair interactions. In order to test for synergies, the PP and CP of a biodiesel (Soy1500) supplemented with several VOCM and PLMA binary cocktails were measured using a specially designed method inspired by ASTM standards. The results were impressive, the combination of additives depressed CP and PP better than any single additive. The PLM and DSC results suggest that the cocktail additives are most

Necessary Competencies for Corporate Wellness Professionals.

ERIC Educational Resources Information Center

Gorman, Dean R.; And Others

A research study attempted to identify necessary components of a strong corporate wellness training program and to establish a sound research base from which valid curricular decisions could be made concerning program design. Responses from a 52-item questionnaire were received from 248 corporate wellness professionals. Results indicated that the…

Polylactides in additive biomanufacturing.

PubMed

Poh, Patrina S P; Chhaya, Mohit P; Wunner, Felix M; De-Juan-Pardo, Elena M; Schilling, Arndt F; Schantz, Jan-Thorsten; van Griensven, Martijn; Hutmacher, Dietmar W

2016-12-15

New advanced manufacturing technologies under the alias of additive biomanufacturing allow the design and fabrication of a range of products from pre-operative models, cutting guides and medical devices to scaffolds. The process of printing in 3 dimensions of cells, extracellular matrix (ECM) and biomaterials (bioinks, powders, etc.) to generate in vitro and/or in vivo tissue analogue structures has been termed bioprinting. To further advance in additive biomanufacturing, there are many aspects that we can learn from the wider additive manufacturing (AM) industry, which have progressed tremendously since its introduction into the manufacturing sector. First, this review gives an overview of additive manufacturing and both industry and academia efforts in addressing specific challenges in the AM technologies to drive toward AM-enabled industrial revolution. After which, considerations of poly(lactides) as a biomaterial in additive biomanufacturing are discussed. Challenges in wider additive biomanufacturing field are discussed in terms of (a) biomaterials; (b) computer-aided design, engineering and manufacturing; (c) AM and additive biomanufacturing printers hardware; and (d) system integration. Finally, the outlook for additive biomanufacturing was discussed. Copyright © 2016 Elsevier B.V. All rights reserved.

Regression with Small Data Sets: A Case Study using Code Surrogates in Additive Manufacturing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kamath, C.; Fan, Y. J.

There has been an increasing interest in recent years in the mining of massive data sets whose sizes are measured in terabytes. While it is easy to collect such large data sets in some application domains, there are others where collecting even a single data point can be very expensive, so the resulting data sets have only tens or hundreds of samples. For example, when complex computer simulations are used to understand a scientific phenomenon, we want to run the simulation for many different values of the input parameters and analyze the resulting output. The data set relating the simulationmore » inputs and outputs is typically quite small, especially when each run of the simulation is expensive. However, regression techniques can still be used on such data sets to build an inexpensive \\surrogate" that could provide an approximate output for a given set of inputs. A good surrogate can be very useful in sensitivity analysis, uncertainty analysis, and in designing experiments. In this paper, we compare different regression techniques to determine how well they predict melt-pool characteristics in the problem domain of additive manufacturing. Our analysis indicates that some of the commonly used regression methods do perform quite well even on small data sets.« less

Advanced turbocharger design study program

NASA Technical Reports Server (NTRS)

Culy, D. G.; Heldenbrand, R. W.; Richardson, N. R.

1984-01-01

The advanced Turbocharger Design Study consisted of: (1) the evaluation of three advanced engine designs to determine their turbocharging requirements, and of technologies applicable to advanced turbocharger designs; (2) trade-off studies to define a turbocharger conceptual design and select the engine with the most representative requirements for turbocharging; (3) the preparation of a turbocharger conceptual design for the Curtiss Wright RC2-32 engine selected in the trade-off studies; and (4) the assessment of market impact and the preparation of a technology demonstration plan for the advanced turbocharger.

Optimal cure cycle design for autoclave processing of thick composites laminates: A feasibility study

NASA Technical Reports Server (NTRS)

Hou, Jean W.

1985-01-01

The thermal analysis and the calculation of thermal sensitivity of a cure cycle in autoclave processing of thick composite laminates were studied. A finite element program for the thermal analysis and design derivatives calculation for temperature distribution and the degree of cure was developed and verified. It was found that the direct differentiation was the best approach for the thermal design sensitivity analysis. In addition, the approach of the direct differentiation provided time histories of design derivatives which are of great value to the cure cycle designers. The approach of direct differentiation is to be used for further study, i.e., the optimal cycle design.

Mixed methods research design for pragmatic psychoanalytic studies.

PubMed

Tillman, Jane G; Clemence, A Jill; Stevens, Jennifer L

2011-10-01

Calls for more rigorous psychoanalytic studies have increased over the past decade. The field has been divided by those who assert that psychoanalysis is properly a hermeneutic endeavor and those who see it as a science. A comparable debate is found in research methodology, where qualitative and quantitative methods have often been seen as occupying orthogonal positions. Recently, Mixed Methods Research (MMR) has emerged as a viable "third community" of research, pursuing a pragmatic approach to research endeavors through integrating qualitative and quantitative procedures in a single study design. Mixed Methods Research designs and the terminology associated with this emerging approach are explained, after which the methodology is explored as a potential integrative approach to a psychoanalytic human science. Both qualitative and quantitative research methods are reviewed, as well as how they may be used in Mixed Methods Research to study complex human phenomena.

Composite power system well-being analysis

NASA Astrophysics Data System (ADS)

Aboreshaid, Saleh Abdulrahman Saleh

The evaluation of composite system reliability is extremely complex as it is necessary to include detailed modeling of both generation and transmission facilities and their auxiliary elements. The most significant quantitative indices in composite power system adequacy evaluation are those which relate to load curtailment. Many utilities have difficulty in interpreting the expected load curtailment indices as the existing models are based on adequacy analysis and in many cases do not consider realistic operating conditions in the system under study. This thesis presents a security based approach which alleviates this difficulty and provides the ability to evaluate the well-being of customer load points and the overall composite generation and transmission power system. Acceptable deterministic criteria are included in the probabilistic evaluation of the composite system reliability indices to monitor load point well-being. The degree of load point well-being is quantified in terms of the healthy and marginal state indices in addition to the traditional risk indices. The individual well-being indices of the different system load points are aggregated to produce system indices. This thesis presents new models and techniques to quantify the well-being of composite generation and, direct and alternating current transmission systems. Security constraints are basically the operating limits which must be satisfied for normal system operation. These constraints depend mainly on the purpose behind the study. The constraints which govern the practical operation of a power system are divided, in this thesis, into three sets namely, steady-state, voltage stability and transient stability constraints. The inclusion of an appropriate transient stability constraint will lead to a more accurate appraisal of the overall power system well-being. This thesis illustrates the utilization of a bisection method in the analytical evaluation of the critical clearing time which forms the

Activating schoolyards: study design of a quasi-experimental schoolyard intervention study.

PubMed

Andersen, Henriette Bondo; Pawlowski, Charlotte Skau; Scheller, Hanne Bebendorf; Troelsen, Jens; Toftager, Mette; Schipperijn, Jasper

2015-05-31

The aim of the Activating Schoolyards Study is to develop, implement, document and assess a comprehensive schoolyard intervention to promote physical activity (PA) during school recess for primary school children (grade 4-8). The intervention is designed to implement organizational and structural changes in the physical environment. The study builds on a quasi-experimental study design using a mixed method approach including: 1) an exploratory study aimed at providing input for the developing process; 2) an evaluation of the effect of the interventions using a combination of accelerometer, GPS and GIS; 3) a process evaluation facilitating the intervention development process and identifying barriers and facilitators in the implementation process; 4) a post-intervention end-user evaluation aimed at exploring who uses the schoolyards and how the schoolyards are used. The seven project schools (cases) were selected by means of an open competition and the interventions were developed using a participatory bottom-up approach. The participatory approach and case selection strategy make the study design novel. The use of a mixed methods design including qualitative as well as quantitative methods can be seen as a strength, as the different types of data complement each other and results of one part of the study informed the following parts. A unique aspect of our study is the use of accelerometers in combination with GPS and GIS in the effect evaluation to objectively determine where and how active the students are in the schoolyard, before and after the intervention. This provides a type of data that, to our knowledge, has not been used before in schoolyard interventions. Exploring the change in behavior in relation to specific intervention elements in the schoolyard will lead to recommendations for schools undergoing schoolyard renovations at some point in the future.

The "Performance of Rotavirus and Oral Polio Vaccines in Developing Countries" (PROVIDE) study: description of methods of an interventional study designed to explore complex biologic problems.

PubMed

Kirkpatrick, Beth D; Colgate, E Ross; Mychaleckyj, Josyf C; Haque, Rashidul; Dickson, Dorothy M; Carmolli, Marya P; Nayak, Uma; Taniuchi, Mami; Naylor, Caitlin; Qadri, Firdausi; Ma, Jennie Z; Alam, Masud; Walsh, Mary Claire; Diehl, Sean A; Petri, William A

2015-04-01

Oral vaccines appear less effective in children in the developing world. Proposed biologic reasons include concurrent enteric infections, malnutrition, breast milk interference, and environmental enteropathy (EE). Rigorous study design and careful data management are essential to begin to understand this complex problem while assuring research subject safety. Herein, we describe the methodology and lessons learned in the PROVIDE study (Dhaka, Bangladesh). A randomized clinical trial platform evaluated the efficacy of delayed-dose oral rotavirus vaccine as well as the benefit of an injectable polio vaccine replacing one dose of oral polio vaccine. This rigorous infrastructure supported the additional examination of hypotheses of vaccine underperformance. Primary and secondary efficacy and immunogenicity measures for rotavirus and polio vaccines were measured, as well as the impact of EE and additional exploratory variables. Methods for the enrollment and 2-year follow-up of a 700 child birth cohort are described, including core laboratory, safety, regulatory, and data management practices. Intense efforts to standardize clinical, laboratory, and data management procedures in a developing world setting provide clinical trials rigor to all outcomes. Although this study infrastructure requires extensive time and effort, it allows optimized safety and confidence in the validity of data gathered in complex, developing country settings. © The American Society of Tropical Medicine and Hygiene.

Improved minimum cost and maximum power two stage genome-wide association study designs.

PubMed

Stanhope, Stephen A; Skol, Andrew D

2012-01-01

In a two stage genome-wide association study (2S-GWAS), a sample of cases and controls is allocated into two groups, and genetic markers are analyzed sequentially with respect to these groups. For such studies, experimental design considerations have primarily focused on minimizing study cost as a function of the allocation of cases and controls to stages, subject to a constraint on the power to detect an associated marker. However, most treatments of this problem implicitly restrict the set of feasible designs to only those that allocate the same proportions of cases and controls to each stage. In this paper, we demonstrate that removing this restriction can improve the cost advantages demonstrated by previous 2S-GWAS designs by up to 40%. Additionally, we consider designs that maximize study power with respect to a cost constraint, and show that recalculated power maximizing designs can recover a substantial amount of the planned study power that might otherwise be lost if study funding is reduced. We provide open source software for calculating cost minimizing or power maximizing 2S-GWAS designs.

Magic Mirror, On the Wall-Which Is the Right Study Design of Them All?-Part II.

PubMed

Vetter, Thomas R

2017-07-01

The assessment of a new or existing treatment or other intervention typically answers 1 of 3 central research-related questions: (1) "Can it work?" (efficacy); (2) "Does it work?" (effectiveness); or (3) "Is it worth it?" (efficiency or cost-effectiveness). There are a number of study designs that, on a situational basis, are appropriate to apply in conducting research. These study designs are generally classified as experimental, quasiexperimental, or observational, with observational studies being further divided into descriptive and analytic categories. This second of a 2-part statistical tutorial reviews these 3 salient research questions and describes a subset of the most common types of observational study designs. Attention is focused on the strengths and weaknesses of each study design to assist in choosing which is appropriate for a given study objective and hypothesis as well as the particular study setting and available resources and data. Specific studies and papers are highlighted as examples of a well-chosen, clearly stated, and properly executed study design type.

Magic Mirror, on the Wall-Which Is the Right Study Design of Them All?-Part I.