Simultaneous quantification of paracetamol, acetylsalicylic acid and papaverine with a validated HPLC method.

PubMed

Kalmár, Eva; Gyuricza, Anett; Kunos-Tóth, Erika; Szakonyi, Gerda; Dombi, György

2014-01-01

Combined drug products have the advantages of better patient compliance and possible synergic effects. The simultaneous application of several active ingredients at a time is therefore frequently chosen. However, the quantitative analysis of such medicines can be challenging. The aim of this study is to provide a validated method for the investigation of a multidose packed oral powder that contained acetylsalicylic acid, paracetamol and papaverine-HCl. Reversed-phase high-pressure liquid chromatography was used. The Agilent Zorbax SB-C18 column was found to be the most suitable of the three different stationary phases tested for the separation of the components of this sample. The key parameters in the method development (apart from the nature of the column) were the pH of the aqueous phase (set to 3.4) and the ratio of the organic (acetonitrile) and the aqueous (25 mM phosphate buffer) phases, which was varied from 7:93 (v/v) to 25:75 (v/v) in a linear gradient, preceded by an initial hold. The method was validated: linearity, precision (repeatability and intermediate precision), accuracy, specificity and robustness were all tested, and the results met the ICH guidelines. © The Author [2013]. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Characterization and identification of iridoid glucosides, flavonoids and anthraquinones in Hedyotis diffusa by high-performance liquid chromatography/electrospray ionization tandem mass spectrometry.

PubMed

Liu, E-Hu; Zhou, Ting; Li, Guo-Bin; Li, Jing; Huang, Xiu-Ning; Pan, Feng; Gao, Ning

2012-01-01

The multiple bioactive constituents in Hedyotis diffusa Willd. (H. diffusa) were extracted and characterized by high-performance liquid chromatography/electrospray ionization tandem mass spectrometry (HPLC-ESI-MS(n)). The optimized separation condition was obtained using an Agilent ZorBax SB-C18 column (4.6×150 mm, 5 μm) and gradient elution with water (containing 0.1% formic acid) and acetonitrile (containing 0.1% formic acid), under which baseline separation for the majority of compounds was achieved. Among the compounds detected, 14 iridoid glucosides, 10 flavonoids, 7 anthraquinones, 1 coumarin and 1 triterpene were unambiguously identified or tentatively characterized based on their retention times and mass spectra in comparison with the data from standards or references. The fragmentation behavior for different types of constituents was also investigated, which could contribute to the elucidation of these constituents in H. diffusa. The present study reveals that even more iridoid glycosides were found in H. diffusa than hitherto assumed. The occurrence of two iridoid glucosides and five flavonoids in particular has not yet been described. This paper marks the first report on the structural characterization of chemical compounds in H. diffusa by a developed HPLC-ESI-MS(n) method. Copyright © 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim.

A validated high-performance liquid chromatography method with diode array detection for simultaneous determination of nine flavonoids in Senecio cannabifolius Less.

PubMed

Niu, Tian-Zeng; Zhang, Yu-Wei; Bao, Yong-Li; Wu, Yin; Yu, Chun-Lei; Sun, Lu-Guo; Yi, Jing-Wen; Huang, Yan-Xin; Li, Yu-Xin

2013-03-25

A reversed phase high performance liquid chromatography method coupled with a diode array detector (HPLC-DAD) was developed for the first time for the simultaneous determination of 9 flavonoids in Senecio cannabifolius, a traditional Chinese medicinal herb. Agilent Zorbax SB-C18 column was used at room temperature and the mobile phase was a mixture of acetonitrile and 0.5% formic acid (v/v) in water in the gradient elution mode at a flow-rate of 1.0mlmin(-1), detected at 360nm. Validation of this method was performed to verify the linearity, precision, limits of detection and quantification, intra- and inter-day variabilities, reproducibility and recovery. The calibration curves showed good linearities (R(2)>0.9995) within the test ranges. The relative standard deviation (RSD) of the method was less than 3.0% for intra- and inter-day assays. The samples were stable for at least 96h, and the average recoveries were between 90.6% and 102.5%. High sensitivity was demonstrated with detection limits of 0.028-0.085μg/ml for flavonoids. The newly established HPLC method represents a powerful technique for the quality assurance of S. cannabifolius. Copyright © 2012 Elsevier B.V. All rights reserved.

Speciation Analysis of Trace Mercury in Sea Cucumber Species of Apostichopus japonicus Using High-Performance Liquid Chromatography Conjunction With Inductively Coupled Plasma Mass Spectrometry.

PubMed

Liu, Hao; Luo, Jiaoyang; Ding, Tong; Gu, Shanyong; Yang, Shihai; Yang, Meihua

2018-03-25

In this paper, a simple and cost-effective method using high-performance liquid chromatography in conjunction with inductively coupled plasma mass spectrometry with a rapid ultrasound-assisted extraction was used for analysis speciation of trace mercury in sea cucumber species of Apostichopus japonicus. The effective separation of inorganic mercury, methylmercury, and ethylmercury was achieved within 10 min using Agilent ZORBAX SB-C 18 analytical and guard columns with an isocratic mobile phase consisting of 8% methanol and 92% H 2 O containing 0.12% L-cysteine (m/v) and 0.01 mol/L ammonium acetate. Mercury species were extracted from A. japonicus samples using a solution containing 2-mercaptoethanol, L-cysteine, and hydrochloric acid and sonicating for 0.5 h. The limits of detection of inorganic mercury, methylmercury, and ethylmercury were 0.12, 0.08, and 0.20 μg/L, and the minimum detectable concentrations (measured at 0.500 g sample volume in 10.00 mL) were 2.4, 1.6, and 4.0 μg/kg, respectively. Analysis of a scallop certified reference material (GBW 10024) revealed accordance between the experimental and certified values. This study provides a reference for the evaluation of mercury speciation in sea cucumber and other seafood.

Semiconducting Ba 3Sn 3Sb 4 and Metallic Ba 7–xSn 11Sb 15–y ( x = 0.4, y = 0.6) Zintl Phases

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Haijie; Narayan, Awadhesh; Stoumpos, Constantinos C.

In this paper, we report the discovery of two ternary Zintl phases Ba 3Sn 3Sb 4 and Ba 7-xSn 11Sb 15-y, (x = 0.4, y = 0.6). Ba 3Sn 3Sb 4 adopts the monoclinic space group P2 1/c with a = 14.669(3) Å, b = 6.9649(14) Å, c = 13.629(3) Å, and β = 104.98(3)°. It features a unique corrugated two-dimensional (2D) structure consisting of [Sn 3Sb 4] 6- layers extending along the ab plane with Ba 2+ atoms sandwiched between them. The non-stoichiometric Ba 6.6Sn 11Sb 14.4 has a complex one-dimensional (1D) structure adopting the orthorhombic space group Pnma,more » with unit cell parameters a = 37.964(8) Å, b = 4.4090(9) Å and c = 24.682(5) Å. It consists of large double Sn-Sb ribbons separated by Ba 2+ atoms. Ba3Sn3Sb4 is an n-type semiconductor which has a narrow energy gap of ~0.18 eV and a room temperature carrier concentration of ~4.2 × 10 18 cm -3. Lastly, Ba 6.6Sn 11Sb 14.4 is determined to be a metal with electrons being the dominant carriers.« less

Semiconducting Ba 3Sn 3Sb 4 and Metallic Ba 7–xSn 11Sb 15–y ( x = 0.4, y = 0.6) Zintl Phases

DOE PAGES

Chen, Haijie; Narayan, Awadhesh; Stoumpos, Constantinos C.; ...

2017-11-08

In this paper, we report the discovery of two ternary Zintl phases Ba 3Sn 3Sb 4 and Ba 7-xSn 11Sb 15-y, (x = 0.4, y = 0.6). Ba 3Sn 3Sb 4 adopts the monoclinic space group P2 1/c with a = 14.669(3) Å, b = 6.9649(14) Å, c = 13.629(3) Å, and β = 104.98(3)°. It features a unique corrugated two-dimensional (2D) structure consisting of [Sn 3Sb 4] 6- layers extending along the ab plane with Ba 2+ atoms sandwiched between them. The non-stoichiometric Ba 6.6Sn 11Sb 14.4 has a complex one-dimensional (1D) structure adopting the orthorhombic space group Pnma,more » with unit cell parameters a = 37.964(8) Å, b = 4.4090(9) Å and c = 24.682(5) Å. It consists of large double Sn-Sb ribbons separated by Ba 2+ atoms. Ba3Sn3Sb4 is an n-type semiconductor which has a narrow energy gap of ~0.18 eV and a room temperature carrier concentration of ~4.2 × 10 18 cm -3. Lastly, Ba 6.6Sn 11Sb 14.4 is determined to be a metal with electrons being the dominant carriers.« less

Yolk-shell structured Sb@C anodes for high energy Na-ion batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Song, Junhua; Yan, Pengfei; Luo, Langli

Despite great advances in sodium-ion battery developments, the search for high energy and stable anode materials remains a challenge. Alloy or conversion-typed anode materials are attractive candidates of high specific capacity and low voltage potential, yet their applications are hampered by the large volume expansion and hence poor electrochemical reversibility and fast capacity fade. Here, we use antimony (Sb) as an example to demonstrate the use of yolk-shell structured anodes for high energy Na-ion batteries. The Sb@C yolk-shell structure prepared by controlled reduction and selective removal of Sb2O3 from carbon coated Sb2O3 nanoparticles can accommodate the Sb swelling upon sodiationmore » and improve the structural/electrical integrity against pulverization. It delivers a high specific capacity of ~554 mAh•g-1, good rate capability (315 mhA•g-1 at 10C rate) and long cyclability (92% capacity retention over 200 cycles). Full-cells of O3-Na0.9[Cu0.22Fe0.30Mn0.48]O2 cathodes and Sb@C-hard carbon composite anodes demonstrate a high specific energy of ~130 Wh•kg-1 (based on the total mass of cathode and anode) in the voltage range of 2.0-4.0 V, ~1.5 times energy of full-cells with similar design using hard carbon anodes.« less

Expansion of antimonato polyoxovanadates with transition metal complexes: (Co(N3C5H15)2)2[{Co(N3C5H15)2}V15Sb6O42(H2O)]·5H2O and (Ni(N3C5H15)2)2[{Ni(N3C5H15)2}V15Sb6O42(H2O)]·8H2O.

PubMed

Antonova, Elena; Näther, Christian; Kögerler, Paul; Bensch, Wolfgang

2012-02-20

Two new polyoxovanadates (Co(N(3)C(5)H(15))(2))(2)[{Co(N(3)C(5)H(15))(2)}V(15)Sb(6)O(42)(H(2)O)]·5H(2)O (1) and (Ni(N(3)C(5)H(15))(2))(2)[{Ni(N(3)C(5)H(15))(2)}V(15)Sb(6)O(42)(H(2)O)]·8H(2)O (2) (N(3)C(5)H(15) = N-(2-aminoethyl)-1,3-propanediamine) were synthesized under solvothermal conditions and structurally characterized. In both structures the [V(15)Sb(6)O(42)(H(2)O)](6-) shell displays the main structural motif, which is strongly related to the {V(18)O(42)} archetype cluster. Both compounds crystallize in the triclinic space group P1 with a = 14.3438(4), b = 16.6471(6), c = 18.9186(6) Å, α = 87.291(3)°, β = 83.340(3)°, γ = 78.890(3)°, and V = 4401.4(2) Å(3) (1) and a = 14.5697(13), b = 15.8523(16), c = 20.2411(18) Å, α = 86.702(11)°, β = 84.957(11)°, γ = 76.941(11)°, and V = 4533.0(7) Å(3) (2). In the structure of 1 the [V(15)Sb(6)O(42)(H(2)O)](6-) cluster anion is bound to a [Co(N(3)C(5)H(15))(2)](2+) complex via a terminal oxygen atom. In the Co(2+)-centered complex, one of the amine ligands coordinates in tridentate mode and the second one in bidentate mode to form a strongly distorted CoN(5)O octahedron. Similarly, in compound 2 an analogous NiN(5)O complex is joined to the [V(15)Sb(6)O(42)(H(2)O)](6-) anion via the same attachment mode. A remarkable difference between the two compounds is the orientation of the noncoordinated propylamine group leading to intermolecular Sb···O contacts in 1 and to Sb···N interactions in 2. In the solid-state lattices of 1 and 2, two additional [M(N(3)C(5)H(15))(2)](2+) complexes act as countercations and are located between the [{M(N(3)C(5)H(15))(2)}V(15)Sb(6)O(42)(H(2)O)](4-) anions. Between the anions and cations strong N-H···O hydrogen bonds are observed. In both compounds the clusters are stacked along the b axis in an ABAB fashion with cations and water molecules occupying the space between the clusters. Magnetic characterization demonstrates that the Ni(2+) and Co(2+) cations do not

Synthesis, crystal structures, and physical properties of the new Zintl phases A{sub 21}Zn{sub 4}Pn{sub 18} (A=Ca, Eu; Pn=As, Sb)—Versatile arrangements of [ZnPn{sub 4}] tetrahedra

DOE Office of Scientific and Technical Information (OSTI.GOV)

Suen, Nian-Tzu; Wang, Yi; Bobev, Svilen, E-mail: bobev@udel.edu

Four new Zintl phases, Ca{sub 21}Zn{sub 4}As{sub 18}, Ca{sub 21}Zn{sub 4}Sb{sub 18}, Eu{sub 21}Zn{sub 4}As{sub 18} and Eu{sub 21}Zn{sub 4}Sb{sub 18} have been synthesized by metal flux reactions. Their structures have been established from single-crystal X-ray diffraction. Despite the similar chemical makeup and the identical formulae, the structures of the four compounds are not the same—Ca{sub 21}Zn{sub 4}As{sub 18}, Ca{sub 21}Zn{sub 4}Sb{sub 18} and Eu{sub 21}Zn{sub 4}As{sub 18} crystallize in the monoclinic space group C2/m (No. 12, Z=4) with the β-Ca{sub 21}Mn{sub 4}Sb{sub 18} structure type, while Eu{sub 21}Zn{sub 4}Sb{sub 18} adopts the Ba{sub 21}Cd{sub 4}Sb{sub 18} structure type withmore » the orthorhombic space group Cmce (No. 64, Z=8). Both structures are based on ZnAs{sub 4} or ZnSb{sub 4} tetrahedra, linked in slightly different ways, and Ca{sup 2+} and Eu{sup 2+} cations that fill the space between them. The structural relationships between the title compounds and other known ternary phases with intricate structures are discussed. Electrical resistivity measurement on single-crystalline Eu{sub 21}Zn{sub 4}Sb{sub 18} suggests an intrinsic semiconductor behavior with a band gap of ca. 0.2 eV. The temperature dependent DC magnetization measurement on the same material indicates Curie–Weiss paramagnetism in the high-temperature regime, and a spontaneous antiferromagnetic ordering below 8 K. The calculated effective moments of Eu confirm the divalent Eu{sup 2+} ground state, as expected from the Zintl–Klemm concept. - Graphical abstract: The four new Zintl phases—Ca{sub 21}Zn{sub 4}As{sub 18}, Ca{sub 21}Zn{sub 4}Sb{sub 18}, Eu{sub 21}Zn{sub 4}As{sub 18}, and Eu{sub 21}Zn{sub 4}Sb{sub 18}—crystallize in two structure types, showing the versatility in the arrangements of ZnAs{sub 4} and ZnSb{sub 4} tetrahedra. - Highlights: • Ca{sub 21}Zn{sub 4}As{sub 18}, Ca{sub 21}Zn{sub 4}Sb{sub 18}, Eu{sub 21}Zn{sub 4}As{sub 18}, and Eu{sub 21}Zn{sub 4}Sb

A new n-type half-Heusler thermoelectric material NbCoSb

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, Lihong; Department of Physics and TcSUH, University of Houston, Houston, TX 77204; He, Ran

2015-10-15

Highlights: • Half-Heusler alloy NbCoSb with 19 valence electron count was studied as TE material. • It is surprising that NbCoSb is n-type. • A maximum ZT of ∼0.4 is achieved at 700 °C without optimization. • It opens up a new route to develop new half-Heusler thermoelectric materials. • It is very interesting that a traditionally thought of VEC of 18 is not required. - Abstract: We surprisingly made a new n-type thermoelectric compound NbCoSb with half-Heusler (HH) structure having valence electron count of 19, different from the traditional 18, which opens up a new route to develop newmore » half-Heusler thermoelectric materials not following the traditional valence electron count of 18. The samples are made by arc melting followed by ball milling and hot pressing. The effect of hot pressing temperature on the thermoelectric properties of NbCoSb samples has been studied. A maximum thermoelectric figure-of-merit (ZT) of ∼0.4 is achieved at 700 °C in NbCoSb sample that is hot pressed at 1000 °C. This work add a new member to HH compounds for thermoelectric applications, although the peak ZT of ∼0.4 is still lower than that of the traditional HHs. Moreover, it is very interesting to see that a traditionally thought of valence electron counts of 18 is not required.« less

Effects of Complex Modification by Sr-Sb on the Microstructures and Mechanical Properties of Al-18 wt % Mg₂Si-4.5Cu Alloys.

PubMed

Sun, Youhong; Ma, Shaoming; Wang, Huiyuan; Chen, Lei; Gao, Ke; Ma, Yinlong; Liu, Baochang

2016-03-04

This research was carried out to investigate the influence of Sr-Sb on the microstructures and mechanical properties of Al-18 wt % Mg₂Si-4.5Cu alloys. After the addition of 0.2 wt % Sr-Sb, the morphologies of primary Mg₂Si transformed from equiaxed dendrite to cube in as-cast alloys and the average size of primary Mg₂Si decreased from ~50 to ~20 μm. The shape of eutectic Mg₂Si changed from Chinese script to short rod. After extrusion and T6 heat treatment, the ultimate tensile strength of modified alloy at room temperature (RT) and 100 °C increased respectively from 229 to 288 MPa, and from 231 to 272 MPa. The elongation-to-failure only slightly improved from 2.9% to 3.8% and from 3.3% to 3.7% at RT and 100 °C, respectively. The tensile fracture surface revealed a transition from brittle fracture to ductile fracture after modifying by 0.2 wt % Sr-Sb.

A LC/UV/Vis method for determination of cyanocobalamin in multivitamin dietary supplements with on-line sample clean-up

USDA-ARS?s Scientific Manuscript database

A HPLC-UV method using a two-column strategy with a switching valve for on-line sample clean-up was developed for the determination of cyanocobalamin (CN-CBL-vitamin B12, in dietary supplements. The method uses two columns, an Agilent Zorbax C8 (150 mm x 4.6 mm, 5 um particle) reversed-phase column...

Yolk-shell structured Sb@C anodes for high energy Na-ion batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Song, Junhua; Yan, Pengfei; Luo, Langli

Despite great advances in sodium-ion battery developments, the search for high energy and stable anode materials remains a challenge. Alloy or conversion-typed anode materials are attractive candidates of high specific capacity and low voltage potential, yet their applications are hampered by the large volume expansion and hence poor electrochemical reversibility and fast capacity fade. Here in this paper, we use antimony (Sb) as an example to demonstrate the use of yolk-shell structured anodes for high energy Na-ion batteries. The Sb@C yolk-shell structure prepared by controlled reduction and selective removal of Sb 2O 3 from carbon coated Sb 2O 3 nanoparticlesmore » can accommodate the Sb swelling upon sodiation and improve the structural/electrical integrity against pulverization. It delivers a high specific capacity of ~ 554 mAh g -1, good rate capability (315 mhA g-1 at 10 C rate) and long cyclability (92% capacity retention over 200 cycles). Full-cells of O3-Na 0.9[Cu0.22Fe 0.30Mn 0.48]O 2 cathodes and Sb@C-hard carbon composite anodes demonstrate a high specific energy of ~ 130 Wh kg-1 (based on the total mass of cathode and anode) in the voltage range of 2.0–4.0 V, ~ 1.5 times energy of full-cells with similar design using hard carbon anodes.« less

Yolk-shell structured Sb@C anodes for high energy Na-ion batteries

DOE PAGES

Song, Junhua; Yan, Pengfei; Luo, Langli; ...

2017-09-04

Despite great advances in sodium-ion battery developments, the search for high energy and stable anode materials remains a challenge. Alloy or conversion-typed anode materials are attractive candidates of high specific capacity and low voltage potential, yet their applications are hampered by the large volume expansion and hence poor electrochemical reversibility and fast capacity fade. Here in this paper, we use antimony (Sb) as an example to demonstrate the use of yolk-shell structured anodes for high energy Na-ion batteries. The Sb@C yolk-shell structure prepared by controlled reduction and selective removal of Sb 2O 3 from carbon coated Sb 2O 3 nanoparticlesmore » can accommodate the Sb swelling upon sodiation and improve the structural/electrical integrity against pulverization. It delivers a high specific capacity of ~ 554 mAh g -1, good rate capability (315 mhA g-1 at 10 C rate) and long cyclability (92% capacity retention over 200 cycles). Full-cells of O3-Na 0.9[Cu0.22Fe 0.30Mn 0.48]O 2 cathodes and Sb@C-hard carbon composite anodes demonstrate a high specific energy of ~ 130 Wh kg-1 (based on the total mass of cathode and anode) in the voltage range of 2.0–4.0 V, ~ 1.5 times energy of full-cells with similar design using hard carbon anodes.« less

Effects of alkyl chain length and anion size on thermal and structural properties for 1-alkyl-3-methylimidazolium hexafluorocomplex salts (C(x)MImAF6, x = 14, 16 and 18; A = P, As, Sb, Nb and Ta).

PubMed

Xu, Fei; Matsumoto, Kazuhiko; Hagiwara, Rika

2012-03-28

A series of 1-alkyl-3-methylimidazolium hexafluorocomplex salts (C(x)MImAF(6), x = 14, 16 and 18, A = P, As, Sb, Nb and Ta) have been characterized by thermal analysis, X-ray diffraction and polarized optical microscopy. A liquid crystalline mesophase is observed for all the C(16)MIm and C(18)MIm salts. The C(14)MIm(+) cation gives a liquid crystalline mesophase only with PF(6)(-). The temperature range of the liquid crystalline mesophase increases with an increase in alkyl chain length or with decrease in anion size. Single-crystal X-ray diffraction revealed that all the C(18)MImAF(6) salts (A = P, As, Sb, Nb and Ta) are isostructural with each other in the crystalline phase and have a layered structure. The interdigitated alkyl chain of the cation has a bent shape like a spoon near the imidazolium ring in the crystalline phase at -100 °C and is tilted with respect to the sheets of the imidazolium headgroups and anions. An increase of temperature increases the ratio of an all-trans conformation to the bent conformation in the crystalline phase. X-ray diffraction and polarized optical microscopy suggested that the liquid crystalline mesophase has a smectic A(2) structure. The interlayer distance increases with a decrease in the anion size since the smaller anion has a stronger coulombic interaction with the imidazolium headgroup, resulting in the decrease of the interdigitated part to give a larger layer spacing.

[Identification of chemical constituents in Sinopodophylli Fructus by HPLC-DAD-ESI-IT-TOF-MSn].

PubMed

Wang, Ai-Hua; Ma, Li-Man; Fan, Shan-Shan; Liu, Guang-Xue; Xu, Feng; Shang, Ming-Ying; Cai, Shao-Qing

2018-01-01

This experiment was performed to analyze and identify the chemical constituents of Sinopodophylli Fructus by HPLC-DAD-ESI-IT-TOF-MSn. The analysis was performed on an Agilent Zorbax SB-C₁₈ (4.6 mm×250 mm, 5 μm) column.The mobile phase consisted of 0.1% formic acid was used for gradient at a flow rate of 1.0 mL·min⁻¹. Electrospray ionization ion trap time-of-flight multistage mass spectrometry was applied for qualitative analysis under positive and negative ion modes. The results indicated that 54 compounds consisted of 18 lignans and 36 flavonoids from Xiaoyelian had been detected by their HRMS data, the information of literature and reference substance. Among them, 27 compounds were reported in Sinopodophylli Fructus for the first time. In conclusion, an HPLC-DAD-ESI-IT-TOF-MSn method was established to qualitative analysis of Xiaoyelian in this study, which will provide the evidence for evaluating the quality of Xiaoyelian herbs, clarifying the mechanism, and guiding the development of pharmacological active ingredients. Copyright© by the Chinese Pharmaceutical Association.

Using the 18-Electron Rule To Understand the Nominal 19-Electron Half-Heusler NbCoSb with Nb Vacancies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zeier, Wolfgang G.; Anand, Shashwat; Huang, Lihong

The 18-electron rule is a widely used criterion in the search for new half-Heusler thermoelectric materials. However, several 19-electron compounds such as NbCoSb have been found to be stable and exhibit thermoelectric properties rivaling state-of-the art materials. Using synchrotron X-ray diffraction and density functional theory calculations, we show that samples with nominal (19-electron) composition NbCoSb actually contain a half-Heusler phase with composition Nb0.84CoSb. The large amount of stable Nb vacancies reduces the overall electron count, which brings the stoichiometry of the compound close to an 18-electron count, and stabilizes the material. Excess electrons beyond 18 electrons provide heavy doping neededmore » to make these good thermoelectric materials. This work demonstrates that considering possible defect chemistry and allowing small variation of electron counting leads to extra degrees of freedom for tailoring thermoelectric properties and exploring new compounds. Here we discuss the 18-electron rule as a guide to find defect-free half-Heusler semiconductors. Other electron counts such as 19-electron NbCoSb can also be expected to be stable as n-type metals, perhaps with cation vacancy defects to reduce the electron count.« less

Characterization of constituents in Stellera chamaejasme L. by rapid-resolution liquid chromatography-diode array detection and electrospray ionization time-of-flight mass spectrometry.

PubMed

Zhao, Liang; Lou, Zi-Yang; Zhu, Zhen-Yu; Zhang, Guo-Qing; Chai, Yi-Feng

2008-01-01

A reliable and rapid method based on rapid-resolution liquid chromatography-diode array detection (RRLC-DAD) and electrospray ionization time-of-flight mass spectrometry (ESI-TOF/MS) has been developed for the isolation and characterization of multiple constituents in the root of Stellera chamaejasme L., which was extracted by sonication with methanol in an optimized procedure. Separation of the multiple constituents was achieved on an Agilent Zorbax XDB-C18 (50x3.0 mm i.d.; 1.8 microm) column using a gradient elution at a flow rate of 0.4 mL/min. The detection wavelength was 210 nm. Mass spectra were acquired in both positive and negative modes. A formula database of the known chemical constituents in the root of Stellera chamaejasme L. was established by an Agilent software. Twenty-two obvious peaks appeared in the total ion chromatogram and nine of them were characterized by TOF/MS. The RRLC-DAD and ESI-TOF/MS method with ultrasonic extraction would be useful for rapid and effective characterization of chemical constituents in the root of Stellera chamaejasme L. Copyright (c) 2007 John Wiley & Sons, Ltd.

Effects of antimony (Sb) on electron trapping near SiO{sub 2}/4H-SiC interfaces

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mooney, P. M.; Jiang, Zenan; Basile, A. F.

To investigate the mechanism by which Sb at the SiO{sub 2}/SiC interface improves the channel mobility of 4H-SiC MOSFETs, 1 MHz capacitance measurements and constant capacitance deep level transient spectroscopy (CCDLTS) measurements were performed on Sb-implanted 4H-SiC MOS capacitors. The measurements reveal a significant concentration of Sb donors near the SiO{sub 2}/SiC interface. Two Sb donor related CCDLTS peaks corresponding to shallow energy levels in SiC were observed close to the SiO{sub 2}/SiC interface. Furthermore, CCDLTS measurements show that the same type of near-interface traps found in conventional dry oxide or NO-annealed capacitors are present in the Sb implanted samples. Thesemore » are O1 traps, suggested to be carbon dimers substituted for O dimers in SiO{sub 2}, and O2 traps, suggested to be interstitial Si in SiO{sub 2}. However, electron trapping is reduced by a factor of ∼2 in Sb-implanted samples compared with samples with no Sb, primarily at energy levels within 0.2 eV of the SiC conduction band edge. This trap passivation effect is relatively small compared with the Sb-induced counter-doping effect on the MOSFET channel surface, which results in improved channel transport.« less

Separation and purification of astaxanthin from Phaffia rhodozyma by preparative high-speed counter-current chromatography.

PubMed

Du, Xiping; Dong, Congcong; Wang, Kai; Jiang, Zedong; Chen, Yanhong; Yang, Yuanfan; Chen, Feng; Ni, Hui

2016-09-01

An effective high-speed counter-current chromatography (HSCCC) method was established for the preparative isolation and purification of astaxanthin from Phaffia rhodozyma. With a two-phase solvent system composed of n-hexane-acetone-ethanol-water (1:1:1:1, v/v/v/v), 100mg crude extract of P. rhodozyma was separated to yield 20.6mg of astaxanthin at 92.0% purity. By further one step silica gel column chromatography, the purity reached 99.0%. The chemical structure of astaxanthin was confirmed by thin layer chromatography (TLC), UV spectroscopy scanning, high performance liquid chromatography with a ZORBAX SB-C18 column and a Waters Nova-pak C18 column, and ESI/MS/MS. Copyright © 2016 Elsevier B.V. All rights reserved.

Rolling and tumbling: status of the SuperAGILE experiment

NASA Astrophysics Data System (ADS)

Del Monte, E.; Costa, E.; di Persio, G.; Donnarumma, I.; Evangelista, Y.; Feroci, M.; Lapshov, I.; Lazzarotto, F.; Mastropietro, M.; Morelli, E.; Pacciani, L.; Rapisarda, M.; Rubini, A.; Soffitta, P.; Tavani, M.; Argan, A.; Trois, A.

2010-07-01

The SuperAGILE experiment is the hard X-ray monitor of the AGILE mission. It is a 2 x one-dimensional imager, with 6-arcmin angular resolution in the energy range 18 - 60 keV and a field of view in excess of 1 steradian. SuperAGILE is successfully operating in orbit since Summer 2007, providing long-term monitoring of bright sources and prompt detection and localization of gamma-ray bursts. Starting on October 2009 the AGILE mission lost its reaction wheel and the satellite attitude is no longer stabilized. The current mode of operation of the AGILE satellite is a Spinning Mode, around the Sun-pointing direction, with an angular velocity of about 0.8 degree/s (corresponding to 8 times the SuperAGILE point spread function every second). In these new conditions, SuperAGILE continuously scans a much larger fraction of the sky, with much smaller exposure to each region. In this paper we review some of the results of the first 2.5 years of "standard" operation of SuperAGILE, and show how new implementations in the data analysis software allows to continue the hard X-ray sky monitoring by SuperAGILE also in the new attitude conditions.

The Holy Grail of Agile Acquisition

DTIC Science & Technology

2010-04-01

Motivation • What is Agility? • Approach C t t Th A i iti S t (Th Bi “A” A i iti P )• on ex : e cqu s on ys em e g cqu s on rocess • Agile Software...Bestsellers…” [Erwin 2009] Motivation • Despite of Erwin’s recommendation… – Agility seems to be a simple concept and it is commonly perceived as a virtue...tension between the numerous stakeholders due to different motivation /behavior • The process elements themselves are complex and ambiguous Slide 16Peter

Agile Metrics: Progress Monitoring of Agile Contractors

DTIC Science & Technology

2014-01-01

epic. The short timeframe is usually called an itera- tion or, in Scrum -based teams, a sprint; multiple iterations make up a release [Lapham 2011...9769 [Rawsthorne 2012] Rawsthorne, Dan. Monitoring Scrum Projects with AgileEVM and Earned Business Value Metrics (EBV). 2012. http...AgileEVM – Earned Value Manage- ment in Scrum Projects.” Presented at Agile2006, 23-28 July 2006. [USAF 2008] United States Air Force. United

Development of an agility assessment module for preliminary fighter design

NASA Technical Reports Server (NTRS)

Ngan, Angelen; Bauer, Brent; Biezad, Daniel; Hahn, Andrew

1996-01-01

A FORTRAN computer program is presented to perform agility analysis on fighter aircraft configurations. This code is one of the modules of the NASA Ames ACSYNT (AirCraft SYNThesis) design code. The background of the agility research in the aircraft industry and a survey of a few agility metrics are discussed. The methodology, techniques, and models developed for the code are presented. FORTRAN programs were developed for two specific metrics, CCT (Combat Cycle Time) and PM (Pointing Margin), as part of the agility module. The validity of the code was evaluated by comparing with existing flight test data. Example trade studies using the agility module along with ACSYNT were conducted using Northrop F-20 Tigershark and McDonnell Douglas F/A-18 Hornet aircraft models. The sensitivity of thrust loading and wing loading on agility criteria were investigated. The module can compare the agility potential between different configurations and has the capability to optimize agility performance in the preliminary design process. This research provides a new and useful design tool for analyzing fighter performance during air combat engagements.

The atomistic mechanism for Sb segregation and As displacement of Sb in InSb(001) surfaces

NASA Astrophysics Data System (ADS)

Anderson, Evan M.; Millunchick, Joanna M.

2018-01-01

Interfacial broadening occurs in mixed-anion alloy heterostructures such as InAs/InAsSb due to both Sb-segregation and As-for-Sb exchange. In order to determine the atomistic mechanisms for these processes, we conduct ab initio calculations coupled with a cluster expansion formalism to determine the surface reconstructions of the pure and As-exposed InSb(001) surfaces. This approach provides a predicted phase diagram for pure InSb that is in better agreement with experiments. Namely, the α2(2 × 4) and α3c(4 × 4) structures are ultimately stable at 0K, but the α(4 × 3) and α2c(2 × 6) are within 1 meV/Å2. Exposure of the InSb(001) surface to As results in the As atoms infiltrating into the crystal and displacing subsurface Sb, thus providing the atomistic mechanisms for experimental observations of the As-for-Sb exchange reaction and Sb segregation. Experiments show that the widely reported A-(1 × 3) reconstruction is actually comprised of multiple reconstructions, which is consistent with the prediction of several nearly stable possible reconstructions.

An Investigation of Agility Issues in Scrum Teams Using Agility Indicators

NASA Astrophysics Data System (ADS)

Pikkarainen, Minna; Wang, Xiaofeng

Agile software development methods have emerged and become increasingly popular in recent years; yet the issues encountered by software development teams that strive to achieve agility using agile methods are yet to be explored systematically. Built upon a previous study that has established a set of indicators of agility, this study investigates what issues are manifested in software development teams using agile methods. It is focussed on Scrum teams particularly. In other words, the goal of the chapter is to evaluate Scrum teams using agility indicators and therefore to further validate previously presented agility indicators within the additional cases. A multiple case study research method is employed. The findings of the study reveal that the teams using Scrum do not necessarily achieve agility in terms of team autonomy, sharing, stability and embraced uncertainty. The possible reasons include previous organizational plan-driven culture, resistance towards the Scrum roles and changing resources.

Effects of Complex Modification by Sr–Sb on the Microstructures and Mechanical Properties of Al–18 wt % Mg2Si–4.5Cu Alloys

PubMed Central

Sun, Youhong; Ma, Shaoming; Wang, Huiyuan; Chen, Lei; Gao, Ke; Ma, Yinlong; Liu, Baochang

2016-01-01

This research was carried out to investigate the influence of Sr–Sb on the microstructures and mechanical properties of Al–18 wt % Mg2Si–4.5Cu alloys. After the addition of 0.2 wt % Sr–Sb, the morphologies of primary Mg2Si transformed from equiaxed dendrite to cube in as-cast alloys and the average size of primary Mg2Si decreased from ~50 to ~20 μm. The shape of eutectic Mg2Si changed from Chinese script to short rod. After extrusion and T6 heat treatment, the ultimate tensile strength of modified alloy at room temperature (RT) and 100 °C increased respectively from 229 to 288 MPa, and from 231 to 272 MPa. The elongation-to-failure only slightly improved from 2.9% to 3.8% and from 3.3% to 3.7% at RT and 100 °C, respectively. The tensile fracture surface revealed a transition from brittle fracture to ductile fracture after modifying by 0.2 wt % Sr–Sb. PMID:28773282

[Simultaneous determination of eleven components in Ginkgo biloba leaves by high performance liquid chromatography method].

PubMed

Lv, Jin-Li; Yang, Biao; Li, Meng-Xuan; Meng, Zhao-Qing; Ma, Shi-Ping; Wang, Zhen-Zhong; Ding, Gang; Huang, Wen-Zhe; Xiao, Wei

2017-03-01

To study Ginkgo biloba leaves in different producing area, we establish an HPLC method for the simultaneously determination of seven flavonoids glycosides and four biflavonoids in G. biloba leaves. The analysis was performed on an Agilent ZORBAX SB-C₁₈ column(4.6 mm×250 mm, 5 μm) wich acetonitrile, and 0.4% phosphoric acid as mobile phase at flow rate of 1 mL•min⁻¹ in a gradient edution, and the detection was carried out at 254 nm.The calibration curves of the seven flavonoids glycosides and four biflavonoids had a good linearitiy with good recoveries. The established HPLC method is simple, rapid, accurate, reliable, and sensitive, and can be applied to the identification and quality control of G. biloba leaves. Copyright© by the Chinese Pharmaceutical Association.

Structural, vibrational, and electronic topological transitions of Bi1.5Sb0.5Te1.8Se1.2 under pressure

NASA Astrophysics Data System (ADS)

Kim, Joon-Seok; Juneja, Rinkle; Salke, Nilesh P.; Palosz, Witold; Swaminathan, Venkataraman; Trivedi, Sudhir; Singh, Abhishek K.; Akinwande, Deji; Lin, Jung-Fu

2018-03-01

Topological insulators have been the subject of intense research interest due to their unique surface states that are topologically protected against scattering or defects. However, the relationship between the crystal structure and topological insulator state remains to be clarified. Here, we show the effects of hydrostatic pressure on the structural, vibrational, and topological properties of the topological insulator Bi1.5Sb0.5Te1.8Se1.2 up to 45 GPa using X-ray diffraction and Raman spectroscopy in a diamond anvil cell, together with first-principles theoretical calculations. Two pressure-induced structural phase transitions were observed: from ambient rhombohedral R 3 ¯ m phase to a monoclinic C2/m phase at ˜13 GPa, and to a disordered I4/mmm phase at ˜22 GPa. In addition, the alloy undergoes several electronic transitions within the R 3 ¯ m phase: indirect to direct bulk band gap transition at ˜5.8 GPa, bulk gap closing with an appearance of Dirac semimetal (DSM) state at ˜8.2 GPa, and to a trivial semimetal state at ˜12.1 GPa. Anomalies in c/a ratio and Raman full width at half maximum that coincide with the DSM phase suggest the contribution of electron-phonon coupling to the transition. Compared to binary end members Bi2Te3, Bi2Se3, and Sb2Te3, the structural phase transition and anomaly were observed at higher pressures in Bi1.5Sb0.5Te1.8Se1.2. These results suggest that the topological transitions are precursors to the structural phase transitions.

Reduction of [Cp*Sb]4 with Subvalent Main-Group Metal Reductants: Syntheses and Structures of [(L1 Mg)4 (Sb4 )] and [(L2 Ga)2 (Sb4 )] Containing Edge-Missing Sb4 Units.

PubMed

Ganesamoorthy, Chelladurai; Krüger, Julia; Wölper, Christoph; Nizovtsev, Anton S; Schulz, Stephan

2017-02-16

[Cp*Sb] 4 (Cp*=C 5 Me 5 ) reacts with [L 1 Mg] 2 and L 2 Ga with formation of [(L 1 Mg) 4 (μ 4 ,η 1:2:2:2 -Sb 4 )] (L 1 =iPr 2 NC[N(2,6-iPr 2 C 6 H 3 )] 2 , 1) and [(L 2 Ga) 2 (μ,η 2:2 -Sb 4 )] (L 2 =HC[C(Me)N(2,6-iPr 2 C 6 H 3 )] 2 , 2). The cleavage of the Sb-Sb and Sb-C bonds in [Cp*Sb] 4 are the crucial steps in both reactions. The formation of 1 occurred by elimination of the Cp* anion and formation of Cp*MgL 1 , while 2 was formed by reductive elimination of Cp* 2 and oxidative addition of L 2 Ga to the Sb 4 unit. 1 and 2 were characterized by heteronuclear NMR spectroscopy and single-crystal X-ray diffraction, and their bonding situation was studied by quantum chemical calculations. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Self-diffusion in 69Ga121Sb/71Ga123Sb isotope heterostructures

NASA Astrophysics Data System (ADS)

Bracht, H.; Nicols, S. P.; Haller, E. E.; Silveira, J. P.; Briones, F.

2001-05-01

Gallium and antimony self-diffusion experiments have been performed in undoped 69Ga121Sb/71Ga123Sb isotope heterostructures at temperatures between 571 and 708 °C under Sb- and Ga-rich ambients. Ga and Sb profiles measured with secondary ion mass spectrometry reveal that Ga diffuses faster than Sb by several orders of magnitude. This strongly suggests that the two self-atom species diffuse independently on their own sublattices. Experimental results lead us to conclude that Ga and Sb diffusion are mediated by Ga vacancies and Sb interstitials, respectively, and not by the formation of a triple defect proposed earlier by Weiler and Mehrer [Philos. Mag. A 49, 309 (1984)]. The extremely slow diffusion of Sb up to the melting temperature of GaSb is proposed to be a consequence of amphoteric transformations between native point defects which suppress the formation of those native defects which control Sb diffusion. Preliminary experiments exploring the effect of Zn indiffusion at 550 °C on Ga and Sb diffusion reveal an enhanced intermixing of the Ga isotope layers compared to undoped GaSb. However, under the same conditions the diffusion of Sb was not significantly affected.

AGILE detection of enhanced gamma-ray emission from the blazar 3C 279

NASA Astrophysics Data System (ADS)

Cardillo, M.; Verrecchia, F.; Pittori, C.; Lucarelli, F.; Ursi, A.; Piano, G.; Minervini, G.; Bulgarelli, A.; Fioretti, V.; Parmiggiani, N.; Tavani, M.; Munar-Adrover, P.; Donnarumma, I.; Vercellone, S.; Striani, E.; Cardillo, M.; Gianotti, F.; Trifoglio, M.; Giuliani, A.; Mereghetti, S.; Caraveo, P.; Perotti, F.; Chen, A.; Argan, A.; Costa, E.; Del Monte, E.; Evangelista, Y.; Feroci, M.; Lazzarotto, F.; Lapshov, I.; Pacciani, L.; Soffitta, P.; Sabatini, S.; Vittorini, V.; Pucella, G.; Rapisarda, M.; Di Cocco, G.; Fuschino, F.; Galli, M.; Labanti, C.; Marisaldi, M.; Pellizzoni, A.; Pilia, M.; Trois, A.; Barbiellini, G.; Vallazza, E.; Longo, F.; Morselli, A.; Picozza, P.; Prest, M.; Lipari, P.; Zanello, D.; Cattaneo, P. W.; Rappoldi, A.; Colafrancesco, S.; Ferrari, A.; Paoletti, F.; Antonelli, A.; Giommi, P.; Salotti, L.; Valentini, G.; D'Amico, F.

2018-06-01

AGILE is detecting enhanced gamma-ray emission above 100 MeV from the blazar 3C 279. Integrating from 2018-06-03 07:56:19 UT to 2018-06-05 07:56:19 UT, a preliminary maximum likelihood analysis yields a detection at a flux F(E > 100 MeV)=(7.0 +/- 1.5) x 10^-6 ph cm^-2 s^-1 and a significance greater than 7 sigma.

Growth and characterization of an InSb infrared photoconductor on Si via an AlSb/GaSb buffer

NASA Astrophysics Data System (ADS)

Jia, Bo Wen; Tan, Kian Hua; Loke, Wan Khai; Wicaksono, Satrio; Yoon, Soon Fatt

2018-05-01

A 99.6% relaxed InSb layer is grown on a 6° offcut (1 0 0) Si substrate via an AlSb/GaSb buffer using molecular beam epitaxy (MBE). A 200 nm GaSb buffer is first grown on Si and the lattice mismatch between them is accommodated by an interfacial misfit (IMF) array consisting of uniformly distributed 90° misfit dislocations. Si delta doping is introduced during the growth of GaSb to reduce the density of threading dislocation. Subsequently, a 50 nm AlSb buffer is grown followed by a 0.8 μm InSb layer. The InSb layer exhibits a 300 K electron mobility of 22,300 cm2/Vs. An InSb photoconductor on Si is demonstrated with a photoconductive gain from 77 K to 200 K under a 700 °C maintained blackbody.

40 CFR 721.3025 - Fatty acids C12-18, C18 unsaturated, C12-18 alkyl esters (generic).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Fatty acids C12-18, C18 unsaturated... Significant New Uses for Specific Chemical Substances § 721.3025 Fatty acids C12-18, C18 unsaturated, C12-18... chemical substance identified generically as fatty acids C12-18, C18 unsaturated, C12-18 alkyl esters (PMNs...

AsSb energetics in argentian sulfosalts

NASA Astrophysics Data System (ADS)

Ghosal, Subhabrata; Sack, Richard O.

1995-09-01

Experimental brackets on As-Sb partitioning between polybasite-pearceite {Pbp; (Cu, Ag) 16(Sb, As) 2S 11} and pyrargyrite-proustite {Ppr; (Cu, Ag) 3(Sb, As)S 3}, and between pyrargyrite-proustite, and miargyrite and smithite {αMi, βMi, Smt; Ag(Sb, As)S 2} (350-400°C; evacuated silica tubes) define standard state Gibbs energies of theAsSb exchange reactions {Ag 16As 2S 11+Ag 3SbS 3=Ag 16Sb 2S 11 + Ag 3AsS 3, Δ Gro Pbp-Ppr = 0.65 ± 0.60 kJ/gfw; Ag 3AsS 3, + AgSbS 2 = Ag 3SbS 3 + AgASS 2, Δ overlineGro Ppr-α Mi = 3.10 ± 0.50 kJ/gfw, Δ Gro PPr-Smt = 1.70 ± 0.50 kJ/gfw and the nonidealities associated with the AsSb substitutions in these minerals (measured by symmetric regular-solution parameters for formula units on a one AsSb site basis; WAsSbPbp = 4.00 ± 0.25 kJ/gfw; WAsSbPpr =6.00 ± 0 .60 kJ/gfw; WAsSbαMi = WAsSbSmt = 7.00 ± 0.50 kJ/gfw). The above constraints applied to the miscibility gap between Ag (Sb, As) S 2 solutions with α-miargyrite and smithite structures at 350°C determine the relative stabilities of these structures in the As and Sb endmembers to be: ( GSbo, α Mi - GSbo, Smt) ˜ -0.63 kJ/gfw; ( GAso, α Mi - GAsSmt) ˜ 0.77 kJ/gfw. Combining these constraints with the calorimetric data of Bryndzia and Kleppa (1988, 1989) and our melting point determinations we have constructed a phase diagram for the AgSbS 2AgAsS 2 subsystem. The salient features of this diagram are (1) eutectic behaviour ( T ˜ 396°C, XAs ˜ 0.50), (2) modest increase in the temperature of the α → β miargyrite transition with As substitution (˜380°C in Sb-subsystem; 386.6°C at XAsMi ˜ 0.36), (3) a 42.5°C depression of the trechmannite-smithite transition with preferential incorporation of Sb in smithite { smithite ( XAs ˜ 0.62) → α-miargyrite ( XAs ˜ 0.34) + trechmannite (X As ˜ 1.00) at ˜277.5°C}, and (4) widening of the miargyrite-trechmannite gap at lower temperatures. The latter feature is consistent with the inference that the most As

Orders of C2 Agility and Implications for Information and Decision-Making

DTIC Science & Technology

2013-06-01

of agility and, in particular, in discussions of resilience. Orders of agility also invite the re-examination of conceptions of value in informing...incompatible interpretations of decision-making and information. It also gives greater confidence that different conceptions of value and assessment...examination of conceptions of value in informing decision- making, leading to the exposition of a hierarchical model of nested decision-making and decision

121Sb and 35Cl NQR in RCN · SbCl5 Complexes

NASA Astrophysics Data System (ADS)

Semin, G. K.; Kuznetsov, S. I.; Raevsky, A. M.; Bryukhova, E. V.

1994-05-01

35Cl and 121Sb NQR spectra of RCN · SbCl5 complexes with R = Et, n-Pr, i-Pr, n-Bu, n-C5H11 , Cl(CH2)2, C6H4CH2, Ph, Cl, Me, CCl3 were measured and /or refined at 77 K. Redistribution of the "transferred charge" in the SbCl5 fragment of the complexes under study was investigated. The existence of a specific region of dispersion of the electron-nuclear motions (DENM) in RCN · SbCl5 complexes was established.

[Study on the analytical methods of catechins in tea and green tea polyphenol samples by high performance liquid chromatography].

PubMed

Dai, J; Wang, H X; Chen, S W; Tang, J

2001-09-01

Hypersil BDS C18 and Zorbax SB C18, suitable to separate simultaneously seven kinds of catechins and caffeine, were screened out from seven brands of reversed-phase columns. Mobile phase was a solution of methanol-water-acetic acid (or trifluoro acetic acid). Seven kinds of catechins in tea samples from six places in China and three green tea polyphenol(GTP) samples from different producers were separated and determined in 30 min by isocratic and gradient elutions. The effects of mobile phase components and temperature of column on retention parameters of catechins and caffeine are reviewed. Chromatographic conditions and pretreatment methods of samples were optimized. Gallocatechin gallate(GCG) and (-)-catechin gallate(CG) were identified by electrospray ionization mass spectrometry(ESI-MS) and prepared by high performance liquid chromatography for quantitative analysis. The other catechins, (-)-epigallocatechin (EGC), (+)-catechin (D-C), (-)-epicatechin(EC), (-)-epigallocatechin gallate(EGCG), (-)-epicatechin gallate(ECG) were identified with standards.

Development and validation of a simple high-performance liquid chromatography analytical method for simultaneous determination of phytosterols, cholesterol and squalene in parenteral lipid emulsions.

PubMed

Novak, Ana; Gutiérrez-Zamora, Mercè; Domenech, Lluís; Suñé-Negre, Josep M; Miñarro, Montserrat; García-Montoya, Encarna; Llop, Josep M; Ticó, Josep R; Pérez-Lozano, Pilar

2018-02-01

A simple analytical method for simultaneous determination of phytosterols, cholesterol and squalene in lipid emulsions was developed owing to increased interest in their clinical effects. Method development was based on commonly used stationary (C 18 , C 8 and phenyl) and mobile phases (mixtures of acetonitrile, methanol and water) under isocratic conditions. Differences in stationary phases resulted in peak overlapping or coelution of different peaks. The best separation of all analyzed compounds was achieved on Zorbax Eclipse XDB C 8 (150 × 4.6 mm, 5 μm; Agilent) and ACN-H 2 O-MeOH, 80:19.5:0.5 (v/v/v). In order to achieve a shorter time of analysis, the method was further optimized and gradient separation was established. The optimized analytical method was validated and tested for routine use in lipid emulsion analyses. Copyright © 2017 John Wiley & Sons, Ltd.

Carrier Concentration Control of GaSb/GaInAsSb System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lazzari, J.-L.; Anda, F. de; Nieto, J.

2007-02-22

The residual carrier concentration of GaSb and GaSb-lattice matched Ga1-xInxAsySb1-y alloys (x = 0.12-0.26; y = 0.9x) grown by liquid phase epitaxy (LPE) and molecular beam epitaxy (MBE) was studied as a function of growth temperature, V/III ratio and alloy composition. Typical carrier concentrations p {approx} 2-3x1016 cm-3 were obtained for undoped GaSb grown by MBE at 480 deg. C, by LPE from Ga-rich melt at low temperature (400 deg. C), and by LPE from Sb-rich melts at {approx}600 deg. C. The native acceptor defect responsible of the high p-type residual doping in GaSb is reduced when the indium concentrationmore » is increased, and disappears for indium rich alloys (x = 0.23, 0.26). Tellurium compensation was used for controlled n-type doping in the (0.05-30)x1017 cm-3 range. A maximum of free carrier concentration was 1.5x1018 cm-3 for LPE layers, 2x1018 cm-3 for MBE layers grown at 1.0 {mu}m/h, 3.5x1018 cm-3 for MBE layers grown at 0.2 {mu}m/h. SIMS measurements showed Te concentrations of more than 1020 at/cm3, suggesting the formation of ternary GaSb1-xTex solid solution.« less

Study on electrical properties of metal/GaSb junctions using metal-GaSb alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nishi, Koichi, E-mail: nishi@mosfet.t.u-tokyo.ac.jp; Yokoyama, Masafumi; Kim, Sanghyeon

2014-01-21

We study the metal-GaSb alloy formation, the structural properties and the electrical characteristics of the metal-alloy/GaSb diodes by employing metal materials such as Ni, Pd, Co, Ti, Al, and Ta, in order to clarify metals suitable for GaSb p-channel metal-oxide-semiconductor field-effect transistors (pMOSFETs) as metal-GaSb alloy source/drain (S/D). It is found that Ni, Pd, Co, and Ti can form alloy with GaSb by rapid thermal annealing at 250, 250, 350, and 450 °C, respectively. The Ni-GaSb and Pd-GaSb alloy formation temperature of 250 °C is lower than the conventional dopant activation annealing for ion implantation, which enable us to lower the processmore » temperature. The alloy layers show lower sheet resistance (R{sub Sheet}) than that of p{sup +}-GaSb layer formed by ion implantation and activation annealing. We also study the electrical characteristics of the metal-alloy/GaSb junctions. The alloy/n-GaSb contact has large Schottky barrier height (ϕ{sub B}) for electrons, ∼0.6 eV, and low ϕ{sub B} for holes, ∼0.2 eV, which enable us to realize high on/off ratio in pMOSFETs. We have found that the Ni-GaSb/GaSb Schottky junction shows the best electrical characteristics with ideal factor (n) of 1.1 and on-current/off-current ratio (I{sub on}/I{sub off}) of ∼10{sup 4} among the metal-GaSb alloy/GaSb junctions evaluated in the present study. These electrical properties are also superior to those of a p{sup +}-n diode fabricated by Be ion implantation with activation annealing at 350 °C. As a result, the Ni-GaSb alloy can be regarded as one of the best materials to realize metal S/D in GaSb pMOSFETs.« less

An investigation of fighter aircraft agility

NASA Technical Reports Server (NTRS)

Valasek, John; Downing, David R.

1993-01-01

This report attempts to unify in a single document the results of a series of studies on fighter aircraft agility funded by the NASA Ames Research Center, Dryden Flight Research Facility and conducted at the University of Kansas Flight Research Laboratory during the period January 1989 through December 1993. New metrics proposed by pilots and the research community to assess fighter aircraft agility are collected and analyzed. The report develops a framework for understanding the context into which the various proposed fighter agility metrics fit in terms of application and testing. Since new metrics continue to be proposed, this report does not claim to contain every proposed fighter agility metric. Flight test procedures, test constraints, and related criteria are developed. Instrumentation required to quantify agility via flight test is considered, as is the sensitivity of the candidate metrics to deviations from nominal pilot command inputs, which is studied in detail. Instead of supplying specific, detailed conclusions about the relevance or utility of one candidate metric versus another, the authors have attempted to provide sufficient data and analyses for readers to formulate their own conclusions. Readers are therefore ultimately responsible for judging exactly which metrics are 'best' for their particular needs. Additionally, it is not the intent of the authors to suggest combat tactics or other actual operational uses of the results and data in this report. This has been left up to the user community. Twenty of the candidate agility metrics were selected for evaluation with high fidelity, nonlinear, non real-time flight simulation computer programs of the F-5A Freedom Fighter, F-16A Fighting Falcon, F-18A Hornet, and X-29A. The information and data presented on the 20 candidate metrics which were evaluated will assist interested readers in conducting their own extensive investigations. The report provides a definition and analysis of each metric; details

Simultaneous determination of six active components by a single standard to determine multicomponents combined with fingerprint analysis for the quality control of Rhizoma Chuanxiong.

PubMed

He, Yufei; Li, Qing; Bi, Kaishun

2015-04-01

To control the quality of Rhizoma Chuanxiong, a method based on high-performance liquid chromatography method coupled with diode array detection was developed for the quantitative analysis of six active ingredients using a single standard to determine multi-components and chemical fingerprint analysis for the first time. The separation was performed on an Agilent Zorbax SB-C18 column by gradient elution with methanol and aqueous phase (containing 0.5% glacial acetic acid) at a flow rate of 1.0 mL/min. The UV wavelength was set at 274 nm. This assay was fully validated with respect to precision, repeatability, and accuracy. All calibration curves showed good linearity (R(2) > 0.9994) within test ranges. The limit of detection and limit of quantification were lower than 0.01 and 0.03 μg/mL, respectively. The relative standard deviation for repeatability and the intermediate precision of six analytes were less than 1.6 and 2.5%, respectively, the overall recovery was 96.1-103.1%. In addition, fingerprint chromatography using hierarchical clustering analysis and similarity analysis was performed to differentiate and classify the samples. The method described here could provide a more comprehensive and reasonable scientific assessment of the quality of Rhizoma Chuanxiong. Therefore, the strategy is feasible, credible, and is easily and effectively adapted for evaluating the quality control of Rhizoma Chuanxiong. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Simple determination of L-hydroxyproline in idiopathic pulmonary fibrosis lung tissues of rats using non-extractive high-performance liquid chromatography coupled with fluorescence detection after pre-column derivatization with novel synthetic 9-acetylimidazol-carbazole.

PubMed

Ren, Yan; Zhao, Juanjuan; Shi, Yanan; Chen, Caiyun; Chen, Xiangming; Lv, Changjun

2017-08-05

L-Hydroxyproline (L-Hyp) is an important biomarker for idiopathic pulmonary fibrosis (IPF). The quantitative methods based on high-performance liquid chromatography coupled with fluorescence detection after pre-column derivatization typically requires complicated derivatization conditions and obtains unstable derivatives. Here, a novel derivatization reagent, 9-acetylimidazol-carbazole, was synthesized for the first time to efficiently and rapidly label the amino groups of L-Hyp. The high-performance liquid chromatography method with pre-column derivatization was performed on an Agilent ZORBAX SB-C 18 column (4.6×250mm, 5μm). The product was measured using fluorescence detection at excitation and emission wavelengths of 232 and 370nm, respectively. The method was validated in specificity, linearity, limit of detection (66.7 fmol), limit of quantification (333.3fmol), intra-day precision (0.75%), inter-day precision (3.82%), stability (3.15%), and recovery (90.7-109.4%). The validated method was successfully applied to the determination of L-Hyp in the lung tissues of healthy and IPF rats. The results showed that the concentration of L-Hyp (3.64mg/g) in the IPF model was significantly higher than the concentration (2.33mg/g) in the healthy control group with P<0.01. This is a new method for the determination of L-Hyp and can be used for other amino acid-related studies in the future. Copyright © 2017. Published by Elsevier B.V.

Effect of Exercise Program Speed, Agility, and Quickness (SAQ) in Improving Speed, Agility, and Acceleration

NASA Astrophysics Data System (ADS)

Azmi, K.; Kusnanik, N. W.

2018-01-01

This study aimed to analyze the effect of speed, agility and quickness training program to increase in speed, agility and acceleration. This study was conducted at 26 soccer players and divided into 2 groups with 13 players each group. Group 1 was given SAQ training program, and Group 2 conventional training program for 8 weeks. This study used a quantitative approach with quasi-experimental method. The design of this study used a matching-only design. Data was collected by testing 30-meter sprint (speed), agility t-test (agility), and run 10 meters (acceleration) during the pretest and posttest. Furthermore, the data was analyzed using paired sample t-test and independent t-test. The results showed: that there was a significant effect of speed, agility and quickness training program in improving in speed, agility and acceleration. In summary, it can be concluded that the speed, agility and quickness training program can improve the speed, agility and acceleration of the soccer players.

Enhanced superconductivity in SnSb under pressure: a first principles study

NASA Astrophysics Data System (ADS)

Sreenivasa Reddy, P. V.; Kanchana, V.

2017-10-01

First principles electronic structure calculations reveal both SnP and SnSb to be stable in the NaCl structure. In SnSb, a first order phase transition from NaCl to CsCl type structure is observed at around 13 GPa, which is also confirmed from enthalpy calculations and agrees well with experimental and other theoretical reports. Calculations of the phonon spectra, and hence the electron-phonon coupling λep and superconducting transition temperature T c, were performed at zero pressure for both the compounds, and at high pressure for SnSb. These calculations report Tc of 0.614 K and 3.083 K for SnP and SnSb respectively, in the NaCl structure—in good agreement with experiment—whilst at the transition pressure, in the CsCl structure, a drastically increased value of T c around 9.18 K (9.74 K at 20 GPa) is found for SnSb, together with a dramatic increase in the electronic density of states at this pressure. The lowest energy acoustic phonon branches in each structure also demonstrate some softening effects, which are well addressed in this work.

Pervasive Agility and Agile Fires in Support of Decisive Action

DTIC Science & Technology

2012-03-29

Pervasive Agility and Agile Fires in Support of Decisive Action FORMAT: Civilian Research Project DATE: 29 March 2012 WORD COUNT : 12,599 PAGES: 54...will face, this pollenization may require creative measures, perhaps virtual or constructive scenarios. The National Training Center at Fort Irwin

Utilization of an agility assessment module in analysis and optimization of preliminary fighter configuration

NASA Technical Reports Server (NTRS)

Ngan, Angelen; Biezad, Daniel

1996-01-01

A study has been conducted to develop and to analyze a FORTRAN computer code for performing agility analysis on fighter aircraft configurations. This program is one of the modules of the NASA Ames ACSYNT (AirCraft SYNThesis) design code. The background of the agility research in the aircraft industry and a survey of a few agility metrics are discussed. The methodology, techniques, and models developed for the code are presented. The validity of the existing code was evaluated by comparing with existing flight test data. A FORTRAN program was developed for a specific metric, PM (Pointing Margin), as part of the agility module. Example trade studies using the agility module along with ACSYNT were conducted using a McDonnell Douglas F/A-18 Hornet aircraft model. Tile sensitivity of thrust loading, wing loading, and thrust vectoring on agility criteria were investigated. The module can compare the agility potential between different configurations and has capability to optimize agility performance in the preliminary design process. This research provides a new and useful design tool for analyzing fighter performance during air combat engagements in the preliminary design.

What Does an Agile Coach Do?

NASA Astrophysics Data System (ADS)

Davies, Rachel; Pullicino, James

The surge in Agile adoption has created a demand for project managers rather than direct their teams. A sign of this trend is the ever-increasing number of people getting certified as scrum masters and agile leaders. Training courses that introduce agile practices are easy to find. But making the transition to coach is not as simple as understanding what agile practices are. Your challenge as an Agile Coach is to support your team in learning how to wield their new Agile tools in creating great software.

Antiferromagnetism in semiconducting SrMn 2 Sb 2 and BaMn 2 Sb 2 single crystals

DOE PAGES

Sangeetha, N. S.; Smetana, V.; Mudring, A. -V.; ...

2018-01-03

Here, crystals of SrMn 2Sb 2 and BaMn 2Sb 2 were grown using Sn flux and characterized by powder and single-crystal x-ray diffraction, respectively, and by single-crystal electrical resistivity ρ, heat capacity C p, and magnetic susceptibility χ measurements versus temperature T, and magnetization versus field M(H) isotherm measurements. SrMn 2Sb 2 adopts the trigonal CaAl 2Si 2-type structure, whereas BaMn 2Sb 2 crystallizes in the tetragonal ThCr 2Si 2-type structure. The ρ(T) data indicate semiconducting behaviors for both compounds with activation energies of ≳0.35 eV for SrMn 2Sb 2 and 0.16 eV for BaMn 2Sb 2. The χ(T) andmore » C p(T) data reveal antiferromagnetic (AFM) ordering at T N = 110 K for SrMn 2Sb 2 and 450 K for BaMn 2Sb 2. The anisotropic χ(T≤T N) data also show that the ordered moments in SrMn 2Sb 2 are aligned in the hexagonal ab plane, whereas the ordered moments in BaMn 2Sb 2 are aligned collinearly along the tetragonal c axis. The ab-plane M(H) data for SrMn 2Sb 2 exhibit a continuous metamagnetic transition at low fields 02Sb 2 exhibits no metamagnetic transitions up to 5.5 T. The χ(T) and C p(T) data for both SrMn 2Sb 2 and BaMn 2Sb 2 indicate strong dynamic short-range AFM correlations above their respective T N up to at least 900 K within a local-moment picture, corresponding to quasi-two-dimensional magnetic behavior. The present results and a survey of the literature for Mn pnictides with the CaAl 2Si 2 and ThCr 2Si 2 crystal structures show that the T N values for the CaAl 2Si 2-type compounds are much smaller than those for the ThCr 2Si 2-type materials.« less

The impact of flying qualities on helicopter operational agility

NASA Technical Reports Server (NTRS)

Padfield, Gareth D.; Lappos, Nick; Hodgkinson, John

1993-01-01

Flying qualities standards are formally set to ensure safe flight and therefore reflect minimum, rather than optimum, requirements. Agility is a flying quality but relates to operations at high, if not maximum, performance. While the quality metrics and test procedures for flying, as covered for example in ADS33C, may provide an adequate structure to encompass agility, they do not currently address flight at high performance. This is also true in the fixed-wing world and a current concern in both communities is the absence of substantiated agility criteria and possible conflicts between flying qualities and high performance. AGARD is sponsoring a working group (WG19) title 'Operational Agility' that deals with these and a range of related issues. This paper is condensed from contributions by the three authors to WG19, relating to flying qualities. Novel perspectives on the subject are presented including the agility factor, that quantifies performance margins in flying qualities terms; a new parameter, based on maneuver acceleration is introduced as a potential candidate for defining upper limits to flying qualities. Finally, a probabilistic analysis of pilot handling qualities ratings is presented that suggests a powerful relationship between inherent airframe flying qualities and operational agility.

The Effect of SbI3 Doping on the Structure and Electrical Properties of n-Type Bi1.8Sb0.2Te2.85Se0.15 Alloy Prepared by the Free Growth Method

NASA Astrophysics Data System (ADS)

Wang, Xiaoyu; Yu, Yuan; Zhu, Bin; Gao, Na; Huang, Zhongyue; Xiang, Bo; Zu, Fangqiu

2018-02-01

Thermoelectric technology is regarded as one of the most promising direct power generation techniques via thermoelectric materials. However, the batch production and scale-up application are hindered because of the high-cost and poor performance. In this work, we adopt the free growth method to synthesize a series of the bulk materials of SbI3-doped Bi1.8Sb0.2Te2.85Se0.15 alloys. The structural and component investigations as well as the electrical properties characterization are carried out. The results show that SbI3 promotes the formation of Te-rich regions in the matrix. In addition, the synergistically optimized electrical conductivity and Seebeck coefficient are attained by controlling the SbI3 doping concentration. Thus, the sample with 0.30 wt.% SbI3 displays a highly increased power factor of ˜ 13.57 μW cm-1 K-2, which is nearly 21 times higher than that of the undoped one. Moreover, the free growth method is reproducible, convenient and economical. Therefore, it has great potential as a promising technology for the batch synthesis.

Agile Mythbusting

DTIC Science & Technology

2015-01-01

0321502752 Coaching Agile Teams Lyssa Adkins ISBN #0321637704 Agile Project Management : Creating Innovative Products – Second Edition Jim Highsmith ISBN...Picatinny Arsenal Lapham, Wrubel Jan 2015 © 2015 Carnegie Mellon University. DoD Acquisition and Innovation Many regulated environments, like the DoD...NEED innovation and NEED incremental improvements to their systems. Many of them are now willing to consider changing their approach if they can do it

An agile implementation of SCRUM

NASA Astrophysics Data System (ADS)

Gannon, Michele

Is Agile a way to cut corners? To some, the use of an Agile Software Development Methodology has a negative connotation - “ Oh, you're just not producing any documentation” . So can a team with no experience in Agile successfully implement and use SCRUM?

SuperAGILE Services at ASDC

NASA Astrophysics Data System (ADS)

Preger, B.; Verrecchia, F.; Pittori, C.; Antonelli, L. A.; Giommi, P.; Lazzarotto, F.; Evangelista, Y.

2008-05-01

The Italian Space Agency Science Data Center (ASDC) is a facility with several responsibilities including support to all the ASI scientific missions as for management and archival of the data, acting as the interface between ASI and the scientific community and providing on-line access to the data hosted. In this poster we describe the services that ASDC provides for SuperAGILE, in particular the ASDC public web pages devoted to the dissemination of SuperAGILE scientific results. SuperAGILE is the X-Ray imager onboard the AGILE mission, and provides the scientific community with orbit-by-orbit information on the observed sources. Crucial source information including position and flux in chosen energy bands will be reported in the SuperAGILE public web page at ASDC. Given their particular interest, another web page will be dedicated entirely to GRBs and other transients, where new event alerts will be notified and where users will find all the available informations on the GRBs detected by SuperAGILE.

Elements of an Art - Agile Coaching

NASA Astrophysics Data System (ADS)

Lundh, Erik

This tutorial gives you a lead on becoming or redefining yourself as an Agile Coach. Introduction to elements and dimensions of state-of-the-art Agile Coaching. How to position the agile coach to be effective in a larger setting. Making the agile transition - from a single team to thousands of people. How to support multiple teams as a coach. How to build a coaches network in your company. Challenges when the agile coach is a consultant and the organization is large.

Interfacial characterization and electrical properties of Ni–GaSb contacts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lin, Kun-Lin, E-mail: kllin@narlabs.org.tw; Chen, Szu-Hung, E-mail: shchen168@narlabs.org.tw

2014-10-06

The microstructural characterization of Ni–GaSb junctions in samples annealed at 300 °C, 350 °C, and 400 °C in a N{sub 2} atmosphere was elucidated using transmission electron microscopy in conjunction with energy-dispersive spectrometry, nanobeam electron diffraction, and grazing-incident X-ray diffraction. Only the NiSb(Ga) phase is formed at the interface of Ni/GaSb when the annealing temperature is below 350 °C. However, three phases—NiSb, Ni{sub 2}Ga{sub 3}, and NiSb(Ga)—are formed simultaneously at the interface between Ni/GaSb when the annealing temperature is increased to 400 °C, which causes a significant increase in the sheet resistance of the Ni–GaSb alloy. These results indicate that the annealing temperature of themore » Ni/GaSb structure should be maintained below 350 °C for the formation of low-resistance metal Ni/GaSb contacts in GaSb-based p-type metal-oxide-semiconductor field-effect transistors.« less

Fluctuations in [11C]SB207145 PET Binding Associated with Change in Threat-Related Amygdala Reactivity in Humans

PubMed Central

Fisher, Patrick MacDonald; Haahr, Mette Ewers; Jensen, Christian Gaden; Frokjaer, Vibe Gedsoe; Siebner, Hartwig Roman; Knudsen, Gitte Moos

2015-01-01

Serotonin critically affects the neural processing of emotionally salient stimuli, including indices of threat; however, how alterations in serotonin signaling contribute to changes in brain function is not well understood. Recently, we showed in a placebo-controlled study of 32 healthy males that brain serotonin 4 receptor (5-HT4) binding, assessed with [11C]SB207145 PET, was sensitive to a 3-week intervention with the selective serotonin reuptake inhibitor fluoxetine, supporting it as an in vivo model for fluctuations in central serotonin levels. Participants also underwent functional magnetic resonance imaging while performing a gender discrimination task of fearful, angry, and neutral faces. This offered a unique opportunity to evaluate whether individual fluctuations in central serotonin levels, indexed by change in [11C]SB207145 binding, predicted changes in threat-related reactivity (ie, fear and angry vs neutral faces) within a corticolimbic circuit including the amygdala and medial prefrontal and anterior cingulate cortex. We observed a significant association such that decreased brain-wide [11C]SB207145 binding (ie, increased brain serotonin levels) was associated with lower threat-related amygdala reactivity, whereas intervention group status did not predict change in corticolimbic reactivity. This suggests that in the healthy brain, interindividual responses to pharmacologically induced and spontaneously occurring fluctuations in [11C]SB207145 binding, a putative marker of brain serotonin levels, affect amygdala reactivity to threat. Our finding also supports that change in brain [11C]SB207145 binding may be a relevant marker for evaluating neurobiological mechanisms underlying sensitivity to threat and serotonin signaling. PMID:25560201

Hole-dominated transport in InSb nanowires grown on high-quality InSb films

NASA Astrophysics Data System (ADS)

Algarni, Zaina; George, David; Singh, Abhay; Lin, Yuankun; Philipose, U.

2016-12-01

We have developed an effective strategy for synthesizing p-type indium antimonide (InSb) nanowires on a thin film of InSb grown on glass substrate. The InSb films were grown by a chemical reaction between S b 2 S 3 and I n and were characterized by structural, compositional, and optical studies. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) studies reveal that the surface of the substrate is covered with a polycrystalline InSb film comprised of sub-micron sized InSb islands. Energy dispersive X-ray (EDX) results show that the film is stoichiometric InSb. The optical constants of the InSb film, characterized using a variable-angle spectroscopic ellipsometer (VASE) shows a maximum value for refractive index at 3.7 near 1.8 eV, and the extinction coefficient (k) shows a maximum value 3.3 near 4.1 eV. InSb nanowires were subsequently grown on the InSb film with 20 nm sized Au nanoparticles functioning as the metal catalyst initiating nanowire growth. The InSb nanowires with diameters in the range of 40-60 nm exhibit good crystallinity and were found to be rich in Sb. High concentrations of anions in binary semiconductors are known to introduce acceptor levels within the band gap. This un-intentional doping of the InSb nanowire resulting in hole-dominated transport in the nanowires is demonstrated by the fabrication of a p-channel nanowire field effect transistor. The hole concentration and field effect mobility are estimated to be ≈1.3 × 1017 cm-3 and 1000 cm2 V-1 s-1, respectively, at room temperature, values that are particularly attractive for the technological implications of utilizing p-InSb nanowires in CMOS electronics.

Strategic agility for nursing leadership.

PubMed

Shirey, Maria R

2015-06-01

This department highlights change management strategies that may be successful in strategically planning and executing organizational change. In this article, the author discusses strategic agility as an important leadership competency and offers approaches for incorporating strategic agility in healthcare systems. A strategic agility checklist and infrastructure-building approach are presented.

The Bright γ-ray Flare of 3C 279 in 2015 June: AGILE Detection and Multifrequency Follow-up Observations

NASA Astrophysics Data System (ADS)

Pittori, C.; Lucarelli, F.; Verrecchia, F.; Raiteri, C. M.; Villata, M.; Vittorini, V.; Tavani, M.; Puccetti, S.; Perri, M.; Donnarumma, I.; Vercellone, S.; Acosta-Pulido, J. A.; Bachev, R.; Benítez, E.; Borman, G. A.; Carnerero, M. I.; Carosati, D.; Chen, W. P.; Ehgamberdiev, Sh. A.; Goded, A.; Grishina, T. S.; Hiriart, D.; Hsiao, H. Y.; Jorstad, S. G.; Kimeridze, G. N.; Kopatskaya, E. N.; Kurtanidze, O. M.; Kurtanidze, S. O.; Larionov, V. M.; Larionova, L. V.; Marscher, A. P.; Mirzaqulov, D. O.; Morozova, D. A.; Nilsson, K.; Samal, M. R.; Sigua, L. A.; Spassov, B.; Strigachev, A.; Takalo, L. O.; Antonelli, L. A.; Bulgarelli, A.; Cattaneo, P.; Colafrancesco, S.; Giommi, P.; Longo, F.; Morselli, A.; Paoletti, F.

2018-04-01

We report the AGILE detection and the results of the multifrequency follow-up observations of a bright γ-ray flare of the blazar 3C 279 in 2015 June. We use AGILE and Fermi gamma-ray data, together with Swift X-ray andoptical-ultraviolet data, and ground-based GASP-WEBT optical observations, including polarization information, to study the source variability and the overall spectral energy distribution during the γ-ray flare. The γ-ray flaring data, compared with as yet unpublished simultaneous optical data that will allow constraints on the big blue bump disk luminosity, show very high Compton dominance values of ∼100, with the ratio of γ-ray to optical emission rising by a factor of three in a few hours. The multiwavelength behavior of the source during the flare challenges one-zone leptonic theoretical models. The new observations during the 2015 June flare are also compared with already published data and nonsimultaneous historical 3C 279 archival data.

Allometric multilevel modelling of agility and dribbling speed by skeletal age and playing position in youth soccer players.

PubMed

Valente-dos-Santos, J; Coelho-e-Silva, M J; Duarte, J; Pereira, J; Rebelo-Gonçalves, R; Figueiredo, A; Mazzuco, M A; Sherar, L B; Elferink-Gemser, M T; Malina, R M

2014-08-01

This study evaluates the contributions of age, skeletal maturation, body size and composition, training and playing position to the development of agility and dribbling speed in young male soccer players (10-18 years) followed longitudinally. 83 players [defenders (n=35), midfielders (n=27), forwards (n=21)] were followed annually over 5 years (average: 4.4 observations per player). Skeletal age (SA), stature, body mass, triceps and subscapular skinfolds, agility and dribbling speed were measured annually. Body composition was estimated from the 2 skinfolds. Annual training volume was estimated from weekly participation forms completed by coaches. The multiplicative allometric models with the best statistical fit showed that statural growth of 1 cm predicts 1.334 s and 1.927 s of improvement in agility and dribbling speed, respectively. Significant independent effects of fat-free mass and annual volume training were found for agility and dribbling speed, respectively (P<0.05). Predicted agility (from 12 to 18 years of SA) and dribbling speed (from 13 to 18 years of SA) differed significantly among players by playing positions (midfielders>forwards>defenders). The present results provide developmental models for the interpretation of intra- and inter-individual variability in agility and dribbling speed among youth soccer players across adolescence, and may provide a framework for trainers and coaches to develop and evaluate individualized training protocols. © Georg Thieme Verlag KG Stuttgart · New York.

Agile Methodology - Past and Future

DTIC Science & Technology

2011-05-01

Takeuchi & Nonaka HBR 1986, p139 RUGBY Waterfall Red vs Agile Black Team- . - Manifesto 2001 SCRUM GRAPHIC* * Adapted from Schwaber (2007) Agile...learning will help Agile manage its vision • Rugby : All Blacks 36 v England 12 Auckland, NZ (6/19/04) Glossary • AFB – Air Force Base • MCS - Maneuver

Opening up the Agile Innovation Process

NASA Astrophysics Data System (ADS)

Conboy, Kieran; Donnellan, Brian; Morgan, Lorraine; Wang, Xiaofeng

The objective of this panel is to discuss how firms can operate both an open and agile innovation process. In an era of unprecedented changes, companies need to be open and agile in order to adapt rapidly and maximize their innovation processes. Proponents of agile methods claim that one of the main distinctions between agile methods and their traditional bureaucratic counterparts is their drive toward creativity and innovation. However, agile methods are rarely adopted in their textbook, "vanilla" format, and are usually adopted in part or are tailored or modified to suit the organization. While we are aware that this happens, there is still limited understanding of what is actually happening in practice. Using innovation adoption theory, this panel will discuss the issues and challenges surrounding the successful adoption of agile practices. In addition, this panel will report on the obstacles and benefits reported by over 20 industrial partners engaged in a pan-European research project into agile practices between 2006 and 2009.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gritti, Fabrice; Guiochon, Georges A

The adsorption isotherms of phenol, caffeine, propranolol chloride, and amitriptyline chloride were measured on three new brands of C{sub 18}-bonded silica that have been designed to be more resistant than conventional C{sub 18}-bonded silica at high pHs (>8). These columns were the 4 {micro}m Bidendate Cogent-C{sub 18} (Microsolv Technology Corporation, Long Branch, NJ, USA), the 3.5 {micro}m Zorbax Extend-C{sub 18} (Agilent Technologies, Palo Alto, CA, USA), and the 5 {micro}m XTerra-C{sub 18} (Waters, Milford, MA, USA). The originality of these adsorbents is due to their surface chemistry, which protects them from rapid hydrolysis or dissolution at extreme pH conditions. Theirmore » adsorption properties were compared to those of the 3 {micro}m Luna-C{sub 18} (Phenomenex, Torrance, CA), which is a more conventional monofunctional material. The adsorption data were acquired by frontal analysis (FA) and the adsorption energy distributions (AEDs) of all systems studied were calculated by the expectation-maximization (EM) method. The experimental results show that neither a simple surface protection (Extend-C{sub 18}) nor the elimination of most of the silanol groups (Cogent-C{sub 18}) is sufficient to avoid a peak tailing of the basic compounds at pH 8 that is of thermodynamic origin. The incorporation of organic moieties in the silica matrix, which was achieved in XTerra-C{sub 18}, the first generation of hybrid methyl/silica material, reduces the silanols activity and is more successful in reducing this peak tailing.« less

MULTIWAVELENGTH OBSERVATIONS OF 3C 454.3. II. THE AGILE 2007 DECEMBER CAMPAIGN

DOE Office of Scientific and Technical Information (OSTI.GOV)

Donnarumma, I.; Pucella, G.; Vittorini, V.

2009-12-20

We report on the second Astrorivelatore Gamma a Immagini Leggero (AGILE) multiwavelength campaign of the blazar 3C 454.3 during the first half of 2007 December. This campaign involved AGILE, Spitzer, Swift, Suzaku, the Whole Earth Blazar Telescope (WEBT) consortium, the Rapid Eye Mount (REM), and the Multicolor Imaging Telescopes for Survey and Monstrous Explosions (MITSuME) telescopes, offering a broadband coverage that allowed for a simultaneous sampling of the synchrotron and inverse Compton (IC) emissions. The two-week AGILE monitoring was accompanied by radio to optical monitoring by WEBT and REM, and by sparse observations in mid-infrared and soft/hard X-ray energy bandsmore » performed by means of Target of Opportunity observations by Spitzer, Swift, and Suzaku, respectively. The source was detected with an average flux of approx250 x 10{sup -8} photons cm{sup -2} s{sup -1} above 100 MeV, typical of its flaring states. The simultaneous optical and gamma-ray monitoring allowed us to study the time lag associated with the variability in the two energy bands, resulting in a possible approx

Agile Software Development

ERIC Educational Resources Information Center

Biju, Soly Mathew

2008-01-01

Many software development firms are now adopting the agile software development method. This method involves the customer at every level of software development, thus reducing the impact of change in the requirement at a later stage. In this article, the principles of the agile method for software development are explored and there is a focus on…

Results of an Experimental Exploration of Advanced Automated Geospatial Tools: Agility in Complex Planning

DTIC Science & Technology

2009-06-01

AUTOMATED GEOSPATIAL TOOLS : AGILITY IN COMPLEX PLANNING Primary Topic: Track 5 – Experimentation and Analysis Walter A. Powell [STUDENT] - GMU...TITLE AND SUBTITLE Results of an Experimental Exploration of Advanced Automated Geospatial Tools : Agility in Complex Planning 5a. CONTRACT NUMBER...Std Z39-18 Abstract Typically, the development of tools and systems for the military is requirement driven; systems are developed to meet

Dissimilatory Sb(V) reduction by microorganisms isolated from Sb-contaminated sediment

NASA Astrophysics Data System (ADS)

Dovick, M. A.; Kulp, T. R.

2013-12-01

Mining and smelting are major sources of trace metal contamination in freshwater systems. Arsenic (As) is a common contaminant derived from certain mining operations and is a known toxic metalloid and carcinogen. Antimony (Sb) is listed as a pollutant of priority interest by the EPA and is presumed to share similar geochemical and toxicological properties with arsenic. Both elements can occur in four different oxidation states (V, III, 0, and -III) under naturally occurring conditions. In aqueous solutions As(V) and Sb(V) predominate in oxygenated surface waters whereas As(III) and Sb(III) are stable in anoxic settings. Numerous studies have examined microbiological redox pathways that utilize As(V) as a terminal electron acceptor for anaerobic respiration, however there have been few studies on microbial mechanisms that may affect the biogeochemical cycling of Sb in the environment. Here we report bacterial reduction of Sb(V) to Sb(III) in anoxic enrichment cultures and bacterial isolates grown from sediment collected from an Sb contaminated pond at a mine tailings site in Idaho (total pond water Sb concentration = 235.2 +/- 136.3 ug/L). Anaerobic sediment microcosms (40 mL) were established in artificial freshwater mineral salt medium, amended with millimolar concentrations of Sb(V), acetate or lactate, and incubated at 27°C for several days. Antimony(V), lactate, and acetate concentrations were monitored during incubation by High Performance Liquid Chromatography (HPLC) and Ion Chromatography (IC). Live sediment microcosms reduced millimolar amendments of Sb(V) to Sb(III) coupled to the oxidation of acetate and lactate, while no activity occurred in killed controls. Enrichment cultures were established by serially diluting Sb(V)-reducing microcosms in mineral salt medium with Sb(V) and acetate, and a Sb(V)-reducing bacterial strain was isolated by plating on anaerobic agar plates amended with millimolar Sb(V) and acetate. Direct cell counting demonstrated that

Agile Walker.

PubMed

Katz, Reuven

2015-01-01

The goal of the Agile Walker is to improve the outdoor mobility of healthy elderly people with some mobility limitations. It is a newly developed, all-terrain walker, equipped with an electric drive system and speed control that can assists elderly people to walk outdoors or to hike. The walker has a unique product design with an attractive look that will appeal to "active-agers" population. This paper describes product design requirements and the development process of the Agile Walker, its features and some preliminary testing results.

A comparative pharmacokinetic study of three flavonoids and three anthraquinones in normal and gastrointestinal motility disorders rat plasma after the oral administration of Wei-Chang-Shu tablet using high-performance liquid chromatography-tandem mass spectrometry.

PubMed

Ren, Yan; Zhao, Weiwei; Zhao, Juanjuan; Chen, Xiangming; Yu, Chen; Liu, Mengan

2017-11-01

A simple, fast and reliable high-performance liquid chromatography-tandem mass spectrometry method was developed and validated for the simultaneous quantification and pharmacokinetic study of three flavonoids (liquiritigenin, isoliquiritigenin and formononetin) and three anthraquinones (emodin, rhein and aloe-emodin), which are the bioactive ingredients of Wei-Chang-Shu tablet found in rat plasma. After extraction by liquid-liquid extraction with ethyl acetate, chromatographic separation was achieved on an Agilent Zorbax SB-C 18 column (4.6 × 150 mm, 5 μm) at a flow rate of 1 mL/min by gradient elution using 0.1% aqueous acetic acid and acetonitrile. The detection was performed using a triple quadrupole mass spectrometer equipped with electrospray ionization source in the negative ionization and selected reaction monitoring mode. Method validation was performed in terms of specificity, carryover, linearity (r > 0.99), intra-/inter-day precision (1.0-10.1%), accuracy (relative error, <7.6%), stability (0.6-13.2%), extract recovery (74.9-91.9%) and matrix effect (89.1-109%). The lower limits of quantification of the six analytes varied from 0.92 to 10.4 ng/mL. The validated method was successfully applied to compare the pharmacokinetic properties of Wei-Chang-Shu tablet in normal rats and in rats with gastrointestinal motility disorders. The results indicated that there were obvious differences in the pharmacokinetic behavior between normal and model rats. This study will be helpful in the clinical application of Wei-Chang-Shu tablet. Copyright © 2017 John Wiley & Sons, Ltd.

Application of high performance liquid chromatography for the profiling of complex chemical mixtures with the aid of chemometrics.

PubMed

Ni, Yongnian; Zhang, Liangsheng; Churchill, Jane; Kokot, Serge

2007-06-15

In this paper, chemometrics methods were applied to resolve the high performance liquid chromatography (HPLC) fingerprints of complex, many-component substances to compare samples from a batch from a given manufacturer, or from those of different producers. As an example of such complex substances, we used a common Chinese traditional medicine, Huoxiang Zhengqi Tincture (HZT) for this research. Twenty-one samples, each representing a separate HZT production batch from one of three manufacturers were analyzed by HPLC with the aid of a diode array detector (DAD). An Agilent Zorbax Eclipse XDB-C18 column with an Agilent Zorbax high pressure reliance cartridge guard-column were used. The mobile phase consisted of water (A) and methanol (B) with a gradient program of 25-65% (v/v, B) during 0-30min, 65-55% (v/v, B) during 30-35min and 55-100% (v/v, B) during 35-60min (flow rate, 1.0mlmin(-1); injection volume, 20mul; and column temperature-ambient). The detection wavelength was adjusted for maximum sensitivity at different time periods. A peak area matrix with 21objectsx14HPLC variables was obtained by sampling each chromatogram at 14 common retention times. Similarities were then calculated to discriminate the batch-to-batch samples and also, a more informative multi-criteria decision making methodology (MCDM), PROMETHEE and GAIA, was applied to obtain more information from the chromatograms in order to rank and compare the complex HZT profiles. The results showed that with the MCDM analysis, it was possible to match and discriminate correctly the batch samples from the three different manufacturers. Fourier transform infrared (FT-IR) spectra taken from samples from several batches were compared by the common similarity method with the HPLC results. It was found that the FT-IR spectra did not discriminate the samples from the different batches.

Tools for Supporting Distributed Agile Project Planning

NASA Astrophysics Data System (ADS)

Wang, Xin; Maurer, Frank; Morgan, Robert; Oliveira, Josyleuda

Agile project planning plays an important part in agile software development. In distributed settings, project planning is severely impacted by the lack of face-to-face communication and the inability to share paper index cards amongst all meeting participants. To address these issues, several distributed agile planning tools were developed. The tools vary in features, functions and running platforms. In this chapter, we first summarize the requirements for distributed agile planning. Then we give an overview on existing agile planning tools. We also evaluate existing tools based on tool requirements. Finally, we present some practical advices for both designers and users of distributed agile planning tools.

Sb-related defects in Sb-doped ZnO thin film grown by pulsed laser deposition

NASA Astrophysics Data System (ADS)

Luo, Caiqin; Ho, Lok-Ping; Azad, Fahad; Anwand, Wolfgang; Butterling, Maik; Wagner, Andreas; Kuznetsov, Andrej; Zhu, Hai; Su, Shichen; Ling, Francis Chi-Chung

2018-04-01

Sb-doped ZnO films were fabricated on c-plane sapphire using the pulsed laser deposition method and characterized by Hall effect measurement, X-ray photoelectron spectroscopy, X-ray diffraction, photoluminescence, and positron annihilation spectroscopy. Systematic studies on the growth conditions with different Sb composition, oxygen pressure, and post-growth annealing were conducted. If the Sb doping concentration is lower than the threshold ˜8 × 1020 cm-3, the as-grown films grown with an appropriate oxygen pressure could be n˜4 × 1020 cm-3. The shallow donor was attributed to the SbZn related defect. Annealing these samples led to the formation of the SbZn-2VZn shallow acceptor which subsequently compensated for the free carrier. For samples with Sb concentration exceeding the threshold, the yielded as-grown samples were highly resistive. X-ray diffraction results showed that the Sb dopant occupied the O site rather than the Zn site as the Sb doping exceeded the threshold, whereas the SbO related deep acceptor was responsible for the high resistivity of the samples.

First-Principles Study of Structural, Electronic, Optical, and Thermal Properties of BeSiSb2 and MgSiSb2

NASA Astrophysics Data System (ADS)

Benlamari, S.; Boukhtouta, M.; Taïri, L.; Meradji, H.; Amirouche, L.; Ghemid, S.

2018-03-01

Structural, electronic, optical, and thermal properties of ternary II-IV-V2 (BeSiSb2 and MgSiSb2) chalcopyrite semiconductors have been calculated using the full-potential linearized augmented plane wave scheme␣in the generalized gradient approximation. The optimized equilibrium structural parameters ( a, c, and u) are in good agreement with theoretical results obtained using other methods. The band structure and density of states reveal that BeSiSb2 has an indirect (Γ-Z) bandgap of about 0.61 eV, whereas MgSiSb2 has a direct (Γ-Γ) bandgap of 0.80 eV. The dielectric function, refractive index, and extinction coefficient were calculated to investigate the optical properties, revealing that BeSiSb2 and MgSiSb2 present very weak birefringence. The temperature dependence of the volume, bulk modulus, Debye temperature, and heat capacities ( C v and C p) was predicted using the quasiharmonic Debye model at different pressures. Significant differences in properties are observed at high pressure and high temperature. We predict that, at 300 K and 0 GPa, the heat capacity at constant volume C v, heat capacity at constant pressure C P, Debye temperature θ D, and Grüneisen parameter γ will be about 94.91 J/mol K, 98.52 J/mol K, 301.30 K, and 2.11 for BeSiSb2 and about 96.08 J/mol K, 100.47 J/mol K, 261.38 K, and 2.20 for MgSiSb2, respectively.

Agile Learning: Sprinting through the Semester

ERIC Educational Resources Information Center

Lang, Guido

2017-01-01

This paper introduces agile learning, a novel pedagogical approach that applies the processes and principles of agile software development to the context of learning. Agile learning is characterized by short project cycles, called sprints, in which a usable deliverable is fully planned, designed, built, tested, reviewed, and launched. An…

Development of sputtered CuSbS2 thin films grown by sequential deposition of binary sulfides

NASA Astrophysics Data System (ADS)

Medina-Montes, M. I.; Vieyra-Brito, O.; Mathews, N. R.; Mathew, X.

2018-05-01

In this work, CuSbS2 thin films were developed by annealing binary precursors deposited sequentially by rf magnetron sputtering. The recrystallization process was optimized and the films were extensively characterized using a number of tools such as XRD, Raman, SEM, energy dispersive x-ray spectroscopy, atomic force microscopy, Hall, UV–vis spectroscopy, Ellipsometry, Seebeck, and photoresponse. The influence of annealing temperature on the structure, morphology, elemental composition, optical and electrical properties are reported. Annealing below 350 °C resulted in famatinite (Cu3SbS4) and chalcostibite (CuSbS2) ternaries as well as binary phases. Phase-pure chalcostibite was obtained in the range of 350 °C–375 °C. At 400 °C, although CuSbS2 was predominant, tetrahedrite phase (Cu12Sb4S13) appeared as an additional phase. The elemental composition of the films was slightly sulfur deficient, and the atomic percentages of Cu, Sb and S showed a dependence on annealing temperature. The material properties of the phase-pure CuSbS2 thin films are: optical band gap in the range of 1.5–1.62 eV, absorption coefficient close to 105 cm‑1, atomic ratios of Cu/Sb ∼1 and (Cu + Sb)/S ∼1.2, crystal size 18.3–24.5 nm and grain size 50–300 nm. The films were photo-sensitive, showed p-type semiconductor behavior. Electrical resistivity, carrier density and hole mobility were 94–459 Ω cm, 1.6–7.0 × 1015 cm‑3 and 8.4–9.5 cm2 V‑1 s respectively.

Evaluation of Basketball-Specific Agility: Applicability of Preplanned and Nonplanned Agility Performances for Differentiating Playing Positions and Playing Levels.

PubMed

Sekulic, Damir; Pehar, Miran; Krolo, Ante; Spasic, Miodrag; Uljevic, Ognjen; Calleja-González, Julio; Sattler, Tine

2017-08-01

Sekulic, D, Pehar, M, Krolo, A, Spasic, M, Uljevic, O, Calleja-González, J, and Sattler, T. Evaluation of basketball-specific agility: applicability of preplanned and nonplanned agility performances for differentiating playing positions and playing levels. J Strength Cond Res 31(8): 2278-2288, 2017-The importance of agility in basketball is well known, but there is an evident lack of studies examining basketball-specific agility performances in high-level players. The aim of this study was to determine the reliability and discriminative validity of 1 standard agility test (test of preplanned agility [change-of-direction speed] over T course, T-TEST), and 4 newly developed basketball-specific agility tests, in defining playing positions and performance levels in basketball. The study comprised 110 high-level male basketball players (height: 194.92 ± 8.09 cm; body mass: 89.33 ± 10.91 kg; age: 21.58 ± 3.92 years). The variables included playing position (Guard, Forward, Center), performance level (first division vs. second division), anthropometrics (body height, body mass, and percentage of body fat), T-TEST, nonplanned basketball agility test performed on dominant (BBAGILdom) and nondominant sides (BBAGILnond), and a preplanned (change-of-direction speed) basketball agility test performed on dominant (BBCODSdom) and nondominant sides (BBCODSnond). The reliability of agility tests was high (intraclass correlation coefficient of 0.81-0.95). Forwards were most successful in the T-TEST (F test: 13.57; p = 0.01). Guards outperformed Centers in BBCODSdom, BBCODSndom, BBAGILdom, and BBAGILnond (F test: 5.06, p = 0.01; 6.57, 0.01; 6.26, 0.01; 3.37, 0.04, respectively). First division Guards achieved better results than second division Guards in BBCODSdom (t: 2.55; p = 0.02; moderate effect size differences), BBAGILdom, and BBAGILnond (t: 3.04 and 3.06, respectively; both p = 0.01 and moderate effect size differences). First division Centers outperformed second division

Microstructural evaluation of strained multilayer InAsSb/InSb infrared detectors by transmission electron microscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chadda, S.; Datye, A.; Dawson, L.R.

InSb/InAsSb strained layer superlattices (SLS) were grown on (001) InSb substrates by molecular beam epitaxy at 425 [degree]C. The active device consisted of an InAs[sub 0.15]Sb[sub 0.85]/InSb superlattice region embedded within a [ital p]-[ital i]-[ital n] junction. The large lattice mismatch between the active device and the substrate required the growth of a buffer. InAs[sub 0.15]Sb[sub 0.85]/InSb SLS, where the average As content was gradually increased, was used as a buffer. The buffer structure was varied to probe its microstructural effect on the capping device. Three distinct approaches (A, B, and C) were used to grow the buffer. Approach Amore » was a four-step buffer where the average content of As in the superlattice was increased in four equal composition steps. This approach led to a crystal with an extensive network of threading dislocations and microcracks. Approach B was to change the average composition in five equal composition steps, thereby decreasing the misfit at the interfaces between composition steps. This led to a decrease in the threading dislocation density but microscopic cracks were still evident. The last approach (C) was to employ migration enhanced epitaxy (MEE) for the growth of the five-step buffer. Samples grown by employing MEE revealed no microcracks but they contained a high density of unusual wiggly'' dislocations at the buffer/device interface. Detailed microstructural analysis by transmission electron microscopy is presented.« less

Onshore and Offshore Outsourcing with Agility: Lessons Learned

NASA Astrophysics Data System (ADS)

Kussmaul, Clifton

This chapter reflects on case study based an agile distributed project that ran for approximately three years (from spring 2003 to spring 2006). The project involved (a) a customer organization with key personnel distributed across the US, developing an application with rapidly changing requirements; (b) onshore consultants with expertise in project management, development processes, offshoring, and relevant technologies; and (c) an external offsite development team in a CMM-5 organization in southern India. This chapter is based on surveys and discussions with multiple participants. The several years since the project was completed allow greater perspective on both the strengths and weaknesses, since the participants can reflect on the entire life of the project, and compare it to subsequent experiences. Our findings emphasize the potential for agile project management in distributed software development, and the importance of people and interactions, taking many small steps to find and correct errors, and matching the structures of the project and product to support implementation of agility.

Gamma-ray Astrophysics with AGILE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Longo, Francesco; Tavani, M.; Barbiellini, G.

2007-07-12

AGILE will explore the gamma-ray Universe with a very innovative instrument combining for the first time a gamma-ray imager and a hard X-ray imager. AGILE will be operational in spring 2007 and it will provide crucial data for the study of Active Galactic Nuclei, Gamma-Ray Bursts, unidentified gamma-ray sources. Galactic compact objects, supernova remnants, TeV sources, and fundamental physics by microsecond timing. The AGILE instrument is designed to simultaneously detect and image photons in the 30 MeV - 50 GeV and 15 - 45 keV energy bands with excellent imaging and timing capabilities, and a large field of view coveringmore » {approx} 1/5 of the entire sky at energies above 30 MeV. A CsI calorimeter is capable of GRB triggering in the energy band 0.3-50 MeV AGILE is now (March 2007) undergoing launcher integration and testing. The PLSV launch is planned in spring 2007. AGILE is then foreseen to be fully operational during the summer of 2007.« less

Identification and quantification of 5,6,7,8-tetrahydro-2-(2-phenylethyl)chromones in Chinese eaglewood by HPLC with diode array detection and MS.

PubMed

Li, Jun; Chen, Dong; Jiang, Yong; Zhang, Qian; Zhang, Liang; Tu, Peng-Fei

2013-12-01

A sensitive and reliable HPLC coupled with diode array detection and MS method was developed and validated for the first time to simultaneously identify and quantify eight characteristic 5,6,7,8-tetrahydro-2-(2-phenylethyl)chromones (THPECs) in Chinese eaglewood. Chromatographic separation was performed on a Zorbax SB C18 column with a gradient of acetonitrile/0.1% formic acid/water as the mobile phase. The MS fragmentation behavior of THPECs was characterized as the successive neutral loss of two molecules of H2 O ([M+H-18-18](+) ) and then two molecules of CO ([M+H-18-18-28-28](+) ), which could be used to differentiate Chinese eaglewood from counterfeits. Validation of the developed analytical method showed good linearity, satisfactory precision, and good recovery. The established method was successfully applied to the simultaneous determination of eight THPECs in ten batches of Chinese eaglewood, which could be used as a tool for the quality control of Chinese eaglewood. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Antiferromagnetism in semiconducting SrMn2Sb2 and BaMn2Sb2 single crystals

NASA Astrophysics Data System (ADS)

Sangeetha, N. S.; Smetana, V.; Mudring, A.-V.; Johnston, D. C.

2018-01-01

Crystals of SrMn2Sb2 and BaMn2Sb2 were grown using Sn flux and characterized by powder and single-crystal x-ray diffraction, respectively, and by single-crystal electrical resistivity ρ , heat capacity Cp, and magnetic susceptibility χ measurements versus temperature T , and magnetization versus field M (H ) isotherm measurements. SrMn2Sb2 adopts the trigonal CaAl2Si2 -type structure, whereas BaMn2Sb2 crystallizes in the tetragonal ThCr2Si2 -type structure. The ρ (T ) data indicate semiconducting behaviors for both compounds with activation energies of ≳0.35 eV for SrMn2Sb2 and 0.16 eV for BaMn2Sb2 . The χ (T ) and Cp(T ) data reveal antiferromagnetic (AFM) ordering at TN = 110 K for SrMn2Sb2 and 450 K for BaMn2Sb2 . The anisotropic χ (T ≤TN) data also show that the ordered moments in SrMn2Sb2 are aligned in the hexagonal a b plane, whereas the ordered moments in BaMn2Sb2 are aligned collinearly along the tetragonal c axis. The a b -plane M (H ) data for SrMn2Sb2 exhibit a continuous metamagnetic transition at low fields 0 Sb2 exhibits no metamagnetic transitions up to 5.5 T. The χ (T ) and C p(T ) data for both SrMn2Sb2 and BaMn2Sb2 indicate strong dynamic short-range AFM correlations above their respective TN up to at least 900 K within a local-moment picture, corresponding to quasi-two-dimensional magnetic behavior. The present results and a survey of the literature for Mn pnictides with the CaAl2Si2 and ThCr2Si2 crystal structures show that the TN values for the CaAl2Si2 -type compounds are much smaller than those for the ThCr2Si2 -type materials.

Strained GaSb/AlAsSb Quantum Wells for p-Channel Field-Effect Transistors

DTIC Science & Technology

2008-01-01

Available online 18 October 2008 PACS: 72.80.Ey 73.61.Ey 81.05.Ea 85.30.Tv Keywords: A3. Molecular beam epitaxy A3. Quantum wells B2. Semiconducting III–V...were grown by molecular beam epitaxy on GaAs substrates. The buffer layer and barrier layers consisted of relaxed AlAsxSb1x. The composition of the...composition in order to control the strain in the GaSb quantum well. The heterostructures studied here are grown by molecular beam epitaxy (MBE) on semi

Towards a Comparative Measure of Legged Agility

DTIC Science & Technology

2014-06-01

body movement with change of velocity or direction in response to a stimulus” [18]. Notwithstanding the many informative and inspiring studies of legged...specific power (watts per kilogram taken over a gait cycle of leg power output relative to leg muscle mass or body mass) [22, 26–28] but it is not scale...closest to the body mass normalized mea- sure we will introduce below. In contrast, characterizing directional aspects of agility performance seems

Analysis and theoretical modeling of 18O enriched carbon dioxide spectrum by CRDS near 1.35 μm: (II) 16O13C18O, 16O13C17O, 12C18O2, 17O12C18O, 12C17O2, 13C18O2 and 17O13C18O

NASA Astrophysics Data System (ADS)

Karlovets, E. V.; Campargue, A.; Kassi, S.; Tashkun, S. A.; Perevalov, V. I.

2017-04-01

This contribution is the second part of the analysis of the room temperature absorption spectrum of 18O enriched carbon dioxide by very high sensitivity Cavity Ring Down spectroscopy between 6977 and 7918 cm-1 (1.43-1.26 μm). Overall, more than 8600 lines belonging to 166 bands of eleven carbon dioxide isotopologues were rovibrationnally assigned. In a first part (Kassi et al. J Quant Spectrosc Radiat Transfer 187 (2017) 414-425, http://dx.doi.org/10.1016/j.jqsrt.2016.09.002), the results relative to mono-substituted isotopologues, 16O12C18O, 16O12C17O, 12C16O2 and 13C16O2, were presented. This second contribution is devoted to the multiply-substituted isotopologues or clumped isotopologues of particular importance in geochemistry: 16O13C18O, 16O13C17O, 12C18O2, 17O12C18O, 12C17O2, 13C18O2 and 17O13C18O. On the basis of the predictions of effective Hamiltonian models, a total of 3195 transitions belonging to 73 bands were rovibrationnally assigned for these seven species. Among the 73 observed bands, 55 are newly reported. All the identified bands correspond to ΔP=10 and 11 series of transitions, where P= 2V1+V2+3V3 is the polyad number (Vi are vibrational quantum numbers). The accurate spectroscopic parameters of 70 bands have been determined from the standard band-by-band analysis. Global fits of the measured line intensities of the ΔP=10 series of transitions of 17O12C18O and 16O13C18O and of the ΔP=11 series of transitions of 12C18O2, 17O12C18O, 16O13C18O and 13C18O2 were performed to determine the corresponding sets of the effective dipole moment parameters.

Agile

NASA Technical Reports Server (NTRS)

Trimble, Jay Phillip

2013-01-01

This is based on a previous talk on agile development. Methods for delivering software on a short cycle are described, including interactions with the customer, the affect on the team, and how to be more effective, streamlined and efficient.

Design and construction of the Mini-Calorimeter of the AGILE satellite

NASA Astrophysics Data System (ADS)

Labanti, C.; Marisaldi, M.; Fuschino, F.; Galli, M.; Argan, A.; Bulgarelli, A.; Di Cocco, G.; Gianotti, F.; Tavani, M.; Trifoglio, M.

2009-01-01

AGILE is a small space mission of the Italian Space Agency (ASI) devoted to gamma-ray and hard-X astrophysics, successfully launched on April 23, 2007. The AGILE Payload is composed of three instruments: a gamma-ray imager based on a tungsten-silicon tracker (ST), for observations in the gamma ray energy range 30 MeV-50 GeV, a Silicon based X-ray detector, SuperAGILE (SA), for imaging in the range 18-60 keV and a CsI(Tl) Mini-Calorimeter (MCAL) that detects gamma rays or charged particles energy loss in the range 300 keV-100 MeV. MCAL is composed of 30 CsI(Tl) scintillator bars with photodiode readout at both ends, arranged in two orthogonal layers. MCAL can work both as a slave of the ST and as an independent gamma-ray detector for transients and gamma-ray bursts detection. In this paper a detailed description of MCAL is presented together with its performance.

Effects of Sb Content (x) on (Bi(1-x)Sb(x))2Te3 Thermoelectric Thin Film Deposited by Effusion Cell Evaporator.

PubMed

Yong, Ho; Na, Sekwon; Gang, Jun-Gu; Jeon, Seong-Jae; Hyun, Seungmin; Lee, Hoo-Jeong

2015-10-01

This paper investigates the effects of the Sb content (x) on (Bi(1-x)Sb(x))2Te3 thermoelectric films with x changing widely from 0 (Sb2Te3) to 1 (Bi2Te3). First, the XRD analysis discloses that with the Sb content (x) increasing, the phase changed gradually from Bi2Te3 to Sb2Te3 as Sb atoms replaced substitutionally Bi atoms. Further microstructure analysis reveals that an extensive grain growth occurred during post-annealing for the samples with high Sb contents. According to the measurement of electrical and thermoelectric properties, the polarity of the charge carrier and Seebeck coefficient switched n-type to p-type in the range of x = 0.45~0.63. For the n-type samples, the power factor is highest when x = 0.18 around 46.01 μW/K(2) whereas Sb2Te3, for the p-type samples, shows the highest value, 62.48 μW/K(2)cm.

Sb content dependent thermoelectric properties of the p-type ZnO:Sb films fabricated by oxidation method

NASA Astrophysics Data System (ADS)

Li, Guojian; Lin, Xiao; Liu, Shiying; Jia, Baohai; Wang, Qiang

2018-05-01

It is important to fabricate stable p-type ZnO:Sb thermoelectric (TE) films for the p-n homojunction TE devices that convert waste heat directly into electricity. In this study, the ZnO:Sb films with different Sb contents were prepared by oxidizing evaporated Zn-Sb films in oxygen. The film with a high Sb content (5.32%) is easy to form Zn4Sb3 and ZnSb compound in the wurtzite ZnO. The resistivity has a sharply reduction with the Sb content from 0.228 Ω·m of 3.95% Sb to 4.68 × 10-5 Ω·m of 5.32% Sb. The lowest resistivity is lower at least one order of magnitude than the results of others with the similar Sb content. The Seebeck coefficient indicates that the 5.32% Sb film remains stable p-type conduction. The carrier concentration is about 1020 cm-3 and is higher at least one order of magnitude than the other results. Raman analysis indicates that the peak of E2high related O sublattice vibrations indicates that the O sites are substituted by Sb3+ ions, which increases the carrier concentration. However, the mobility is relatively weak because the intrinsic host lattice defects activated as vibrating complexes. The power factor of the p-type ZnO:Sb of the 5.32% Sb film at 427 °C is 46.79 μW/m·K2.

Growth and characterization of AlInAsSb layers lattice-matched to GaSb

NASA Astrophysics Data System (ADS)

Tournet, J.; Rouillard, Y.; Tournié, E.

2017-11-01

We report on the growth by solid-source MBE of random-alloy AlxIn1-xAsySb1-y layers lattice-matched to (0 0 1)-GaSb substrates, with xAl ∈ [0.25; 0.75]. The samples quality and morphology were characterized by X-ray diffraction, Nomarski microscopy and atomic force microscopy. Layers grown at 400 °C demonstrated smooth surfaces and no sign of phase decomposition. Samples with xAl ≤ 0.60 demonstrated photoluminescence (PL) at 300 K whereas samples with higher Al content only demonstrated PL at low temperature. Samples grown at 430 °C, in contrast, exhibited PL at low temperature only, whatever their composition. Inferred bandgap energies corroborate the estimation of a non-null quaternary bowing parameter made by Donati, Kaspi and Malloy in Journal of Applied Physics 94 (2003) 5814. Upon annealing, the PL peak energies increased, getting even closer to the theoretical values. These results are in agreement with recently published results on digital AlInAsSb alloys. Our work, which reports the first evidence for PL emission from random-alloy AlInAsSb layers lattice-matched to GaSb, opens the way to their use in optoelectronic devices.

Metalorganic chemical vapor deposition growth of InAs/GaSb type II superlattices with controllable AsxSb1-x interfaces

PubMed Central

2012-01-01

InAs/GaSb type II superlattices were grown on (100) GaSb substrates by metalorganic chemical vapor deposition (MOCVD). A plane of mixed As and Sb atoms connecting the InAs and GaSb layers was introduced to compensate the tensile strain created by the InAs layer in the SL. Characterizations of the samples by atomic force microscopy and high-resolution X-ray diffraction demonstrate flat surface morphology and good crystalline quality. The lattice mismatch of approximately 0.18% between the SL and GaSb substrate is small compared to the MOCVD-grown supperlattice samples reported to date in the literature. Considerable optical absorption in 2- to 8-μm infrared region has been realized. PACS: 78.67.Pt; 81.15.Gh; 63.22.Np; 81.05.Ea PMID:22373387

An Improved LC-MS/MS Method for Simultaneous Determination of the Eleven Bioactive Constituents for Quality Control of Radix Angelicae Pubescentis and Its Related Preparations

PubMed Central

Li, Jin; Zhang, Qiu-Hong; He, Jun; Liu, Er-wei; Gao, Xiu-mei; Chang, Yan-xu

2015-01-01

An improved LC-MS/MS method was developed for simultaneous determination of eleven bioactive constituents of Radix Angelicae Pubescentis and its related preparations. It was the first report on the quantification of bioactive constituents in different preparations of Radix Angelicae Pubescentis by LC-MS/MS analytical method. These samples were separated with an Agilent Zorbax Extend reversed-phase C18 column (1.8 μm, 4.6 × 100 mm) by linear gradient elution using aqueous ammonium acetate and acetonitrile as mobile phase. The flow rate was 0.3 mL min−1. The eleven bioactive constituents showed good regression (R > 0.990) within test ranges and the recoveries were in the range of 87.1–110%. The limit of detections and quantifications for most of the major constituents were less than 0.5 and 1.0 ng mL−1, respectively. All results indicated that the developed method could be readily utilized as a suitable quality control method for Radix Angelicae Pubescentis and related preparations. PMID:26078992

Quantum dots grown in the InSb/GaSb system by liquid-phase epitaxy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parkhomenko, Ya. A.; Dement’ev, P. A.; Moiseev, K. D., E-mail: mkd@iropt2.ioffe.rssi.ru

2016-07-15

The first results of the liquid-phase epitaxial growth of quantum dots in the InSb/GaSb system and atomic-force microscopy data on the structural characteristics of the quantum dots are reported. It is shown that the surface density, shape, and size of nanoislands depend on the deposition temperature and the chemical properties of the matrix surface. Arrays of InSb quantum dots on GaSb (001) substrates are produced in the temperature range T = 450–465°C. The average dimensions of the quantum dots correspond to a height of h = 3 nm and a base dimension of D = 30 nm; the surface densitymore » is 3 × 10{sup 9} cm{sup –2}.« less

Agile battle management efficiency for command, control, communications, computers and intelligence (C4I)

NASA Astrophysics Data System (ADS)

Blasch, Erik; Bélanger, Micheline

2016-05-01

Various operations such as civil-military co-operation (CIMIC) affairs require orchestration of communications, assets, and actors. A key component includes technology advancements to enable coordination among people and machines the ability to know where things are, who to coordinate with, and open and consistent lines of communication. In this paper, we explore concepts of battle management (BM) to support high-tempo emergency response scenarios such as a disaster action response team (DART). Three concepts highlighted of agile battle management (ABM) include source orchestration (e.g., sensors and domains), battle management language (BML) development (e.g., software and ontologies), and command and control (C2) coordination (e.g., people and visualization); which require correlation and de-confliction. These concepts of ABM support the physical, information, and cognitive domains for efficient command, control, communications, and information (C3I) to synchronize data and people for efficient and effective operations.

The Mediating Role of Organizational Learning in the Relationship of Organizational Intelligence and Organizational Agility.

PubMed

Bahrami, Mohammad Amin; Kiani, Mohammad Mehdi; Montazeralfaraj, Raziye; Zadeh, Hossein Fallah; Zadeh, Morteza Mohammad

2016-06-01

Organizational learning is defined as creating, absorbing, retaining, transferring, and application of knowledge within an organization. This article aims to examine the mediating role of organizational learning in the relationship of organizational intelligence and organizational agility. This analytical and cross-sectional study was conducted in 2015 at four teaching hospitals of Yazd city, Iran. A total of 370 administrative and medical staff contributed to the study. We used stratified-random method for sampling. Required data were gathered using three valid questionnaires including Alberkht (2003) organizational intelligence, Neefe (2001) organizational learning, and Sharifi and Zhang (1999) organizational agility questionnaires. Data analysis was done through R and SPSS 18 statistical software. The results showed that organizational learning acts as a mediator in the relationship of organizational intelligence and organizational agility (path coefficient = 0.943). Also, organizational learning has a statistical relationship with organizational agility (path coefficient = 0.382). Our findings suggest that the improvement of organizational learning abilities can affect an organization's agility which is crucial for its survival.

Quench hardening of Sb0.2 Bi1.8Te3, Bi2Te2.8Se0.2 and Sn0.2 Bi1.8Te3 single crystals

NASA Astrophysics Data System (ADS)

Soni, P. H.

2018-02-01

The V2-VI3 intermetallics are narrow band gap semiconductors and well known for their thermoelectric properties. They therefore offer a convenient route to tune band gap for manipulating thermoelectric parameters. The V group element Sb can be fruitfully used to substitute Bi in various proportions thus forming a psuedobinary solid solution. The electronic in general and the thermoelectric properties in particular of this psuedobinary have been amply reported. However there are no reports found on mechanical properties. I have used Sb0.2 Bi1.8Te3, Bi2Te2.8Se0.2 and Sn0.2 Bi1.8Te3single crystals grown using Bridgman technique for the quenching treatment followed by hardness testing. Vickers hardness tests were conducted on the cleavage planes of the crystals quenched from various high temperatures and the quench hardenening coefficient values have been determined. The hardness tests were carried out at various applied loads also to explore load dependence of the measured hardness. The results are reported in the paper.

The reaction mechanism of SnSb and Sb thin film anodes for Na-ion batteries studied by X-ray diffraction, 119Sn and 121Sb Mössbauer spectroscopies

DOE PAGES

Baggetto, Loïc; Hah, Hien-Yoong; Jumas, Jean-Claude; ...

2014-06-01

The electrochemical reaction of Sb and SnSb anode materials with Na results in the formation of amorphous materials. To understand the resulting phases and electrochemical capacities we studied the reaction products local order using 119Sn and 121Sb Mössbauer spectroscopies in conjunction with measurements performed on model powder compounds of Na-Sn and Na-Sb to further clarify the reactions steps. For pure Sb the discharge (sodiation) starts with the formation of an amorphous phase composed of atomic environments similar to those found in NaSb, and proceeds further by the formation of environments similar to that present in Na 3Sb. The reversible reactionmore » takes place during a large portion of the charge process. At full charge the anode material still contains a substantial fraction of Na, which explains the lack of recrystallization into crystalline Sb. The reaction of SnSb yields Na 3Sb crystalline phase at full discharge at higher temperatures (65 and 95°C) while the room temperature reaction yields amorphous compounds. The electrochemically-driven, solid-state amorphization reaction occurring at room temperature is governed by the simultaneous formation of Na-coordinated Sn and Sb environments, as monitored by the decrease (increase) of the 119Sn ( 121Sb) Mössbauer isomer shifts. Overall, the monitoring of the hyperfine parameters enables to correlate the changes in Na content to the individual Sn and Sb local chemical environments.« less

The two-dimensional tunnel structures of K3Sb5O14 and K2Sb4O11

NASA Technical Reports Server (NTRS)

Hong, H. Y.-P.

1974-01-01

The structures of K3Sb5O14 and K2Sb4O11 have been solved by the single-crystal X-ray direct method and the heavy-atom method, respectively. The structure of K3Sb5O14 is orthorhombic, with space group Pbam and cell parameters a = 24.247 (4), b = 7.157 (2), c = 7.334 (2) A, Z = 4. The structure of K2Sb4O11 is monoclinic, with space group C2/m and cell parameters a = 19.473 (4), b = 7.542 (1), c = 7.198 (1) A, beta = 94.82 (2) deg, Z = 4. A full-matrix least-squares refinement gave R = 0.072 and R = 0.067, respectively. In both structures, oxygen atoms form an octahedron around each Sb atom and an irregular polyhedron around each K atom. By sharing corners and edges, the octahedra form a skeleton network having intersecting b-axis and c-axis tunnels. The K(+) ions, which have more than ten oxygen near neighbors, are located in these tunnels. Evidence for K(+)-ion transport within and between tunnels comes from ion exchange of the alkali ions in molten salts and anisotropic temperature factors that are anomalously large in the direction of the tunnels.

Reliability and Factorial Validity of Non-Specific and Tennis-Specific Pre-Planned Agility Tests; Preliminary Analysis

PubMed Central

Sekulic, Damir; Uljevic, Ognjen; Peric, Mia; Spasic, Miodrag; Kondric, Miran

2017-01-01

Abstract Agility is an important quality in tennis, yet there is an evident lack of studies focussing on the applicability of tennis-specific agility performances and comparing them to equivalent non-specific agility performances. The aim of this study was to evaluate the reliability and factorial validity of three tests of pre-planned agility, performed in specific (with a tennis racquet) and non-specific (without a tennis racquet) conditions. The sample consisted of 33 tennis players (13 males and 20 females; age: 18.3 ± 1.1 years and 18.6 ± 1.3 years; body height: 185.4 ± 51 cm and 169.3 ± 4.2 cm, 74.0 ± 4.4 kg and 61.2 ± 3.1 kg, respectively). The variables comprised three agility tests: a 20-yard test, a T-test and the Illinois test, all performed in both specific and non-specific conditions. Between-subject and within-subject reliability were found to be high (Cronbach Alpha: 0.93 to 0.98; Coefficient of Variation: 3 to 8%), with better within-subject reliability and stability of the measurement for specific tests. Pearson’s product moment correlations between the non-specific and specific agility performances were high (r ≥0.84), while factor analysis extracted only one significant latent dimension on the basis of the Guttman-Kaiser criterion. The results of the 20-yard test were better when the test was conducted in the specific conditions (t-test = 2.66; p < 0.05). For the Illinois test, superior results were recorded in the non-specific conditions (t-test = 2.96; p < 0.05), which can be explained by the test duration (about 20 s) and non-specific locomotion forms such as rotational movements. Considering the findings of the present study, when testing tennis-specific pre-planned agility, we suggest using tests of short duration (less than 10 s) and sport-specific types of locomotion. PMID:28210343

Chemical Substitution-Induced and Competitive Formation of 6H and 3C Perovskite Structures in Ba3-xSrxZnSb2O9: The Coexistence of Two Perovskites in 0.3 ≤ x ≤ 1.0.

PubMed

Li, Jing; Jiang, Pengfei; Gao, Wenliang; Cong, Rihong; Yang, Tao

2017-11-20

6H and 3C perovskites are important prototype structures in materials science. We systemically studied the structural evolution induced by the Sr 2+ -to-Ba 2+ substitution to the parent 6H perovskite Ba 3 ZnSb 2 O 9 . The 6H perovskite is only stable in the narrow range of x ≤ 0.2, which attributes to the impressibility of [Sb 2 O 9 ]. The preference of 90° Sb-O-Sb connection and the strong Sb 5+ -Sb 5+ electrostatic repulsion in [Sb 2 O 9 ] are competitive factors to stabilize or destabilize the 6H structure when chemical pressure was introduced by Sr 2+ incorporation. Therefore, in the following, a wide two-phase region containing 1:2 ordered 6H-Ba 2.8 Sr 0.2 ZnSb 2 O 9 and rock-salt ordered 3C-Ba 2 SrZnSb 2 O 9 was observed (0.3 ≤ x ≤ 1.0). In the final, the successive symmetry descending was established from cubic (Fm3̅m, 1.3 ≤ x ≤ 1.8) to tetragonal (I4/m, 2.0 ≤ x ≤ 2.4), and finally to monoclinic (I2/m, 2.6 ≤ x ≤ 3.0). Here we proved that the electronic configurations of B-site cations, with either empty, partially, or fully filled d-shell, would also affect the structure stabilization, through the orientation preference of the B-O covalent bonding. Our investigation gives a deeper understanding of the factors to the competitive formation of perovskite structures, facilitating the fine manipulation on their physical properties.

Antimony in recent, ombrotrophic peat from Switzerland and Scotland: Comparison with natural background values (5,320 to 8,020 14C yr BP) and implications for the global atmospheric Sb cycle

NASA Astrophysics Data System (ADS)

Shotyk, William; Krachler, Michael; Chen, Bin

2004-03-01

The lowest concentrations, atmospheric fluxes, and enrichments of Sb in a Swiss bog were found in peat samples dating from 8,020 to 5,320 14C yr BP when Sb inputs were proportional to those of Sc and effectively controlled by deposition of soil dust. For comparison with these ancient samples, modern peat samples from five rural areas of Switzerland and two remote areas of Scotland and Shetland are highly contaminated with Sb, with enrichments of the order of 30 to 80 times. "Lithogenic" Sb concentrations calculated using the Sc concentrations and background Sb/Sc ratio are dwarfed at all sites by "anthropogenic" Sb. The chronology and intensity of the Sb enrichments are in many ways similar to those of Pb which indicates that (1) Sb, like Pb, is well preserved in ombrotrophic peat and (2) the extent of human impacts on the geochemical cycle of Sb is comparable to that of Pb. The similar distribution of Sb and Pb can be explained in terms of their chemical and mineralogical associations, with most lead minerals being rich in Sb. Assuming that the "background" Sb flux (0.35 μg/m2/yr) from the Swiss bog is representative of preanthropogenic deposition rates worldwide, the global flux of natural Sb is estimated at 154 T/a. Using the natural Pb flux published by [1987] of 2600 T/a and the "background" Pb/Sb ratio (29) of the preanthropogenic peat samples, the global flux of natural Sb is estimated at 90 T/a. Either way, these values (90 to 154 T/a) are considerably lower than the current estimate of natural Sb to the global atmosphere (2400 T/a) published by [2001]. Assuming that the current estimate of anthropogenic Sb to the global atmosphere (1600 T/a) is correct [, 2001], the ratio of anthropogenic to natural Sb emissions is on the order of 10 to 18. Taken together, the data from modern and ancient peat samples suggests that the impact of human activities on the global geochemical cycle of Sb may have been underestimated by an order of magnitude. Like Pb, Sb has no

An Agile Course-Delivery Approach

ERIC Educational Resources Information Center

Capellan, Mirkeya

2009-01-01

In the world of software development, agile methodologies have gained popularity thanks to their lightweight methodologies and flexible approach. Many advocates believe that agile methodologies can provide significant benefits if applied in the educational environment as a teaching method. The need for an approach that engages and motivates…

Ultraviolet and visible range plasmonics in the topological insulator Bi1.5Sb0.5Te1.8Se1.2

NASA Astrophysics Data System (ADS)

Ou, Jun-Yu; So, Jin-Kyu; Adamo, Giorgio; Sulaev, Azat; Wang, Lan; Zheludev, Nikolay I.

2014-10-01

The development of metamaterials, data processing circuits and sensors for the visible and ultraviolet parts of the spectrum is hampered by the lack of low-loss media supporting plasmonic excitations. This has driven the intense search for plasmonic materials beyond noble metals. Here we show that the semiconductor Bi1.5Sb0.5Te1.8Se1.2, also known as a topological insulator, is also a good plasmonic material in the blue-ultraviolet range, in addition to the already-investigated terahertz frequency range. Metamaterials fabricated from Bi1.5Sb0.5Te1.8Se1.2 show plasmonic resonances from 350 to 550 nm, while surface gratings exhibit cathodoluminescent peaks from 230 to 1,050 nm. The observed plasmonic response is attributed to the combination of bulk charge carriers from interband transitions and surface charge carriers of the topological insulator. The importance of our result is in the identification of new mechanisms of negative permittivity in semiconductors where visible range plasmonics can be directly integrated with electronics.

Focused Logistics: Putting Agility in Agile Logistics

DTIC Science & Technology

2011-05-19

list, ahead of companies like American Express, DuPont and Coca Cola ; Supports nearly 1,900 weapon systems; DLA manages eight supply chains and...35 7) Force Health Protection...Distribution, Information Fusion, Joint Theater Logistics Command and Control, Multinational Logistics, Joint Health Services Support, and Agile

Reverse phase HPLC method for detection and quantification of lupin seed γ-conglutin.

PubMed

Mane, Sharmilee; Bringans, Scott; Johnson, Stuart; Pareek, Vishnu; Utikar, Ranjeet

2017-09-15

A simple, selective and accurate reverse phase HPLC method was developed for detection and quantitation of γ-conglutin from lupin seed extract. A linear gradient of water and acetonitrile containing trifluoroacetic acid (TFA) on a reverse phase column (Agilent Zorbax 300SB C-18), with a flow rate of 0.8ml/min was able to produce a sharp and symmetric peak of γ-conglutin with a retention time at 29.16min. The identity of γ-conglutin in the peak was confirmed by mass spectrometry (MS/MS identification) and sodium dodecyl sulphate polyacrylamide gel electrophoresis (SDS-PAGE) analysis. The data obtained from MS/MS analysis was matched against the specified database to obtain the exact match for the protein of interest. The proposed method was validated in terms of specificity, linearity, sensitivity, precision, recovery and accuracy. The analytical parameters revealed that the validated method was capable of selectively performing a good chromatographic separation of γ-conglutin from the lupin seed extract with no interference of the matrix. The detection and quantitation limit of γ-conglutin were found to be 2.68μg/ml and 8.12μg/ml respectively. The accuracy (precision and recovery) analysis of the method was conducted under repeatable conditions on different days. Intra-day and inter-day precision values less than 0.5% and recovery greater than 97% indicated high precision and accuracy of the method for analysis of γ-conglutin. The method validation findings were reproducible and can be successfully applied for routine analysis of γ-conglutin from lupin seed extract. Copyright © 2017 Elsevier B.V. All rights reserved.

Simultaneous determination of seventeen mycotoxins residues in Puerariae lobatae radix by liquid chromatography-tandem mass spectrometry.

PubMed

Wang, Shufang; Cheng, Ling; Ji, Shen; Wang, Ke

2014-09-01

This work reported an efficient and accurate liquid chromatography tandem mass spectrometry (LC-MS/MS) method for simultaneous determination of seventeen mycotoxins in Puerariae lobatae radix, a frequently used traditional Chinese medicine (TCM). The effects of four different clean-up methods, including TC-M160, TC-T220, Mycosep 227, and QuEChERS method, on the recoveries of mycotoxins were investigated and compared. Finally, TC-M160 was chosen for better recovery and repeatability for mycotoxins analysis. The analytes were separated on an Agilent ZORBAX SB C18 column (4.6mm×250mm, 5μm particle size), and eluted with a mobile phase consisting of (A) water containing 0.1% formic acid and (B) acetonitrile containing 0.1% formic acid at a flow rate of 0.6mL/min. The separated compounds were detected by a triple quadrupole mass spectrometer operating in positive electrospray ionization with multiple reaction monitoring (MRM) mode. The results of method validation accorded with the requirement of analytical method for mycotoxins in COMMISSION REGULATION (EC) No 401/2006. The developed method was successfully applied for determination of mycotoxins in seventeen batches of Puerariae lobatae radix collected from different provinces of China. Three batches of them were found with contamination of mycotoxins AFB1 at (0.751±0.176)μg/kg, T-2 at (1.10±0.01)μg/kg, and T-2 at (0.853±0.044)μg/kg, respectively. The results demonstrated that the proposed method was suitable for monitoring mycotoxins residues in Puerariae lobatae radix. Copyright © 2014 Elsevier B.V. All rights reserved.

Enabling Agile Testing through Continuous Integration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stolberg, Sean E.

2009-08-24

A Continuous Integration system is often considered one of the key elements involved in supporting an agile software development and testing environment. As a traditional software tester transitioning to an agile development environment it became clear to me that I would need to put this essential infrastructure in place and promote improved development practices in order to make the transition to agile testing possible. This experience report discusses a continuous integration implementation I lead last year. The initial motivations for implementing continuous integration are discussed and a pre and post-assessment using Martin Fowler's "Practices of Continuous Integration" is provided alongmore » with the technical specifics of the implementation. Finally, I’ll wrap up with a retrospective of my experiences implementing and promoting continuous integration within the context of agile testing.« less

Explaining the Obvious - How Do You Teach Agile?

NASA Astrophysics Data System (ADS)

Lundh, Erik

Agile is now a hot topic and many organizations decide on adopting “agile” without really knowing how and why. This workshop will explore how fresh and seasoned agile coaches teach traditional and novel agile concepts, by example, with discussions. All participants are invited to show and tell about agile with an audience of peers. It might be the fresh first time with an audience, or golden hits that served you well for years.

Separation of 1,3-substituted imidazoles for quality control of a Lewis acidic ionic liquid for aluminum electroplating.

PubMed

Kosmus, Patrick; Steiner, Oliver; Goessler, Walter; Gollas, Bernhard

2014-05-01

Ionic liquids (ILs) are already used or have great potential in many industrial applications. Knowledge about their unique physicochemical characteristics makes ILs suitable for the electrodeposition of metals with very low negative potentials. Aluminum with its good corrosion protection behavior has great capability to be electroplated from IL electrolytes on steel substrates. The stability of the chosen electrolyte is very important to ensure industrial applicability. In this study, temperature and electrochemical long-term stability from electrolytes based on a Lewis acidic mixture of AlCl3 and 1-ethyl-3-methylimidazolium chloride are investigated. A published method was modified to identify possible degradation products using mass spectrometric detection. The optimized method used an Agilent Zorbax SB-Phenyl column (2.0 × 150 mm, 5 μm particles) with a 20 mmol TFA and 5% ACN mobile phase. This method allowed the quantification of several imidazoles from 0.1 to 100 mg/L. When analyzing the long-term stressed electrolytes, no significant changes in electrolyte composition could be observed. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Preparation, spectroscopic characterization and antimicrobial activities of mixed metal (Sb and Bi) bridged derivatives with mixed sulfur donor ligands

NASA Astrophysics Data System (ADS)

Joshi, Sapana; Chauhan, H. P. S.; Carpenter, Nitin

2017-01-01

This article explores the syntheses of six mixed metal derivatives of antimony(III) and bismuth(III) by the reaction of ethane-1,2-dithiol and metal bis derivatives of dithiocarbamates and/or dithiophosphates ligands in 1:1:1 M stoichiometry. These derivatives have been characterized by physicochemical [elemental analysis (C, H, N, S, Sb and Bi), molecular weight and melting point determinations], spectral [UV-Visible, FTIR, NMR (1H, 13C and 31P)], powder X-ray diffraction studies. These derivatives have nano-ranged crystallite size (8.18-18.04 nm) with monoclinic crystal system. All the synthesized derivatives have two metal centers (Sb and Bi) which elevate the zone of inhibition against four bacterial and two fungal species as compared to single metal species (metal precursors) as well as standard drugs.

Self-assembling of impurity clusters in AlN:(Ga, BV, CV), (BV, CV = P, As; P, Sb; As, Sb)

NASA Astrophysics Data System (ADS)

Elyukhin, V. A.

2015-11-01

The self-assembling conditions of arrays of tetrahedral impurity clusters of two types in zinc blende AlN:(Ga, BV, CV), (BV, CV = P, As; P, Sb; As, Sb) are represented. Doping with one cation and two anion isoelectronic impurities transforms AlN into AlN-rich GaxAl1-xBVyCVzN1-y-z alloy of GaBV, GaCV, GaN, AlBV, AlCV and AlN. The cause of self-assembling is the preference of GaBV, GaCV and AlN bonding over that of GaN, AlBV, AlCV. The conditions are considered from 0 °C to 1000 °C in the dilute and ultra dilute limits for the cation and anion impurities, correspondingly. The temperature ranges between the cluster occurrence and self-assembling completion when the same anion impurities are in clusters are very small. 1P4Ga and 1As4Ga cluster occurrence temperatures are equal, correspondingly, to 797 °C and 736 °C at Ga content 2% and P and As contents 0.01%. 1P4Ga and 1Sb4Ga cluster occurrence temperatures are equal, correspondingly, to 976 °C and 736 °C at the same impurity contents. The cluster densities in AlN:(Ga, As, Sb) are close to those in AlN:(Ga, P, Sb). The results demonstrate that studied semiconductors are promising materials to produce arrays of identical ∼1 nm low band gap objects of two types embedded in the wide band gap matrix.

Some Findings Concerning Requirements in Agile Methodologies

NASA Astrophysics Data System (ADS)

Rodríguez, Pilar; Yagüe, Agustín; Alarcón, Pedro P.; Garbajosa, Juan

Agile methods have appeared as an attractive alternative to conventional methodologies. These methods try to reduce the time to market and, indirectly, the cost of the product through flexible development and deep customer involvement. The processes related to requirements have been extensively studied in literature, in most cases in the frame of conventional methods. However, conclusions of conventional methodologies could not be necessarily valid for Agile; in some issues, conventional and Agile processes are radically different. As recent surveys report, inadequate project requirements is one of the most conflictive issues in agile approaches and better understanding about this is needed. This paper describes some findings concerning requirements activities in a project developed under an agile methodology. The project intended to evolve an existing product and, therefore, some background information was available. The major difficulties encountered were related to non-functional needs and management of requirements dependencies.

Introduction to Stand-up Meetings in Agile Methods

NASA Astrophysics Data System (ADS)

Hasnain, Eisha; Hall, Tracy

2009-05-01

In recent years, agile methods have become more popular in the software industry. Agile methods are a new approach compared to plan-driven approaches. One of the most important shifts in adopting an agile approach is the central focus given to people in the process. This is exemplified by the independence afforded to developers in the development work they do. This work investigates the opinions of practitioners about daily stand-up meetings in the agile methods and the role of developer in that. For our investigation we joined a yahoo group called "Extreme Programming". Our investigation suggests that although trust is an important factor in agile methods. But stand-ups are not the place to build trust.

Frequency agile optical parametric oscillator

DOEpatents

Velsko, S.P.

1998-11-24

The frequency agile OPO device converts a fixed wavelength pump laser beam to arbitrary wavelengths within a specified range with pulse to pulse agility, at a rate limited only by the repetition rate of the pump laser. Uses of this invention include Laser radar, LIDAR, active remote sensing of effluents/pollutants, environmental monitoring, antisensor lasers, and spectroscopy. 14 figs.

Frequency agile optical parametric oscillator

DOEpatents

Velsko, Stephan P.

1998-01-01

The frequency agile OPO device converts a fixed wavelength pump laser beam to arbitrary wavelengths within a specified range with pulse to pulse agility, at a rate limited only by the repetition rate of the pump laser. Uses of this invention include Laser radar, LIDAR, active remote sensing of effluents/pollutants, environmental monitoring, antisensor lasers, and spectroscopy.

Update 2016: Considerations for Using Agile in DoD Acquisition

DTIC Science & Technology

2016-12-01

What Is Agile? 4 2.1 Agile Manifesto and Principles—A Brief History 4 2.2 A Practical Definition 6 2.3 Example Agile Method 6 2.4 Example Agile...5.8 Team Composition 45 5.9 Culture 46 6 Conclusion 48 Appendix A: Examples of Agile Methods 50 Appendix B: Common Objections to Agile 53...thank all those who have contributed to our knowledge of apply- ing “other than traditional” methods for software system acquisition and management over

[Simultaneous determination of aspartame and alitame in jellies and preserved fruits by HPLC].

PubMed

Jiang, Dingguo; Fang, Congrong; Yang, Dajin

2012-05-01

To establish a determination method for aspartame and alitame in jellies and preserved fruits. Aspartame and alitame in jellies were extracted with 80% methanol at 70 degrees C. Preserved fruits were homogenized with water and then were extracted with 50% methanol. A chromatographic column Zorbax SB-C18 was used; the mobile phase was methanol/water (40 + 60, volume ratio), and a diode array detector was used for the detection at wavelength 200 nm. The limits of quantification of aspartame and alitame were both 8 mg/kg for jellies and both 20 mg/kg for preserved fruits; the calibration curves were linear in the range of tested concentration. The correlation coefficients were better than 0.9996. The average recovery rates were in the range of 98.1% -101.2%, the relative standard deviations were 2.21% - 4.10%. The method is simple, practical, accurate, reliable and successful in the determination of aspartame and alitame in jellies and preserved fruits from various brands on markets.

MULTIWAVELENGTH OBSERVATIONS OF 3C 454.3. III. EIGHTEEN MONTHS OF AGILE MONITORING OF THE 'CRAZY DIAMOND'

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vercellone, S.; Romano, P.; D'Ammando, F.

2010-03-20

We report on 18 months of multiwavelength observations of the blazar 3C 454.3 (Crazy Diamond) carried out in the period 2007 July-2009 January. In particular, we show the results of the AGILE campaigns which took place on 2008 May-June, 2008 July-August, and 2008 October-2009 January. During the 2008 May-2009 January period, the source average flux was highly variable, with a clear fading trend toward the end of the period, from an average gamma-ray flux F{sub E>100{sub MeV}} {approx}> 200 x 10{sup -8} photons cm{sup -2} s{sup -1} in 2008 May-June, to F{sub E>100{sub MeV}} {approx} 80 x 10{sup -8} photonsmore » cm{sup -2} s{sup -1} in 2008 October-2009 January. The average gamma-ray spectrum between 100 MeV and 1 GeV can be fit by a simple power law, showing a moderate softening (from GAMMA{sub GRID} {approx} 2.0 to GAMMA{sub GRID} {approx} 2.2) toward the end of the observing campaign. Only 3sigma upper limits can be derived in the 20-60 keV energy band with Super-AGILE, because the source was considerably off-axis during the whole time period. In 2007 July-August and 2008 May-June, 3C 454.3 was monitored by Rossi X-ray Timing Explorer (RXTE). The RXTE/Proportional Counter Array (PCA) light curve in the 3-20 keV energy band shows variability correlated with the gamma-ray one. The RXTE/PCA average flux during the two time periods is F{sub 3-20{sub keV}} = 8.4 x 10{sup -11} erg cm{sup -2} s{sup -1}, and F{sub 3-20{sub keV}} = 4.5 x 10{sup -11} erg cm{sup -2} s{sup -1}, respectively, while the spectrum (a power law with photon index GAMMA{sub PCA} = 1.65 +- 0.02) does not show any significant variability. Consistent results are obtained with the analysis of the RXTE/High-Energy X-Ray Timing Experiment quasi-simultaneous data. We also carried out simultaneous Swift observations during all AGILE campaigns. Swift/XRT detected 3C 454.3 with an observed flux in the 2-10 keV energy band in the range (0.9-7.5) x 10{sup -11} erg cm{sup -2} s{sup -1} and a photon index in

Investigating the strategic antecedents of agility in humanitarian logistics.

PubMed

L'Hermitte, Cécile; Brooks, Benjamin; Bowles, Marcus; Tatham, Peter H

2017-10-01

This study investigates the strategic antecedents of operational agility in humanitarian logistics. It began by identifying the particular actions to be taken at the strategic level of a humanitarian organisation to support field-level agility. Next, quantitative data (n=59) were collected on four strategic-level capabilities (being purposeful, action-focused, collaborative, and learning-oriented) and on operational agility (field responsiveness and flexibility). Using a quantitative analysis, the study tested the relationship between organisational capacity building and operational agility and found that the four strategic-level capabilities are fundamental building blocks of agility. Collectively they account for 52 per cent of the ability of humanitarian logisticians to deal with ongoing changes and disruptions in the field. This study emphasises the need for researchers and practitioners to embrace a broader perspective of agility in humanitarian logistics. In addition, it highlights the inherently strategic nature of agility, the development of which involves focusing simultaneously on multiple drivers. © 2017 The Author(s). Disasters © Overseas Development Institute, 2017.

Agile Methods for Open Source Safety-Critical Software.

PubMed

Gary, Kevin; Enquobahrie, Andinet; Ibanez, Luis; Cheng, Patrick; Yaniv, Ziv; Cleary, Kevin; Kokoori, Shylaja; Muffih, Benjamin; Heidenreich, John

2011-08-01

The introduction of software technology in a life-dependent environment requires the development team to execute a process that ensures a high level of software reliability and correctness. Despite their popularity, agile methods are generally assumed to be inappropriate as a process family in these environments due to their lack of emphasis on documentation, traceability, and other formal techniques. Agile methods, notably Scrum, favor empirical process control, or small constant adjustments in a tight feedback loop. This paper challenges the assumption that agile methods are inappropriate for safety-critical software development. Agile methods are flexible enough to encourage the rightamount of ceremony; therefore if safety-critical systems require greater emphasis on activities like formal specification and requirements management, then an agile process will include these as necessary activities. Furthermore, agile methods focus more on continuous process management and code-level quality than classic software engineering process models. We present our experiences on the image-guided surgical toolkit (IGSTK) project as a backdrop. IGSTK is an open source software project employing agile practices since 2004. We started with the assumption that a lighter process is better, focused on evolving code, and only adding process elements as the need arose. IGSTK has been adopted by teaching hospitals and research labs, and used for clinical trials. Agile methods have matured since the academic community suggested they are not suitable for safety-critical systems almost a decade ago, we present our experiences as a case study for renewing the discussion.

Social Protocols for Agile Virtual Teams

NASA Astrophysics Data System (ADS)

Picard, Willy

Despite many works on collaborative networked organizations (CNOs), CSCW, groupware, workflow systems and social networks, computer support for virtual teams is still insufficient, especially support for agility, i.e. the capability of virtual team members to rapidly and cost efficiently adapt the way they interact to changes. In this paper, requirements for computer support for agile virtual teams are presented. Next, an extension of the concept of social protocol is proposed as a novel model supporting agile interactions within virtual teams. The extended concept of social protocol consists of an extended social network and a workflow model.

Synthesis and Initial in Vivo Studies with [11C]SB-216763: The First Radiolabeled Brain Penetrative Inhibitor of GSK-3

PubMed Central

2015-01-01

Quantifying glycogen synthase kinase-3 (GSK-3) activity in vivo using positron emission tomography (PET) imaging is of interest because dysregulation of GSK-3 is implicated in numerous diseases and neurological disorders for which GSK-3 inhibitors are being considered as therapeutic strategies. Previous PET radiotracers for GSK-3 have been reported, but none of the published examples cross the blood–brain barrier. Therefore, we have an ongoing interest in developing a brain penetrating radiotracer for GSK-3. To this end, we were interested in synthesis and preclinical evaluation of [11C]SB-216763, a high-affinity inhibitor of GSK-3 (Ki = 9 nM; IC50 = 34 nM). Initial radiosyntheses of [11C]SB-216763 proved ineffective in our hands because of competing [3 + 3] sigmatropic shifts. Therefore, we have developed a novel one-pot two-step synthesis of [11C]SB-216763 from a 2,4-dimethoxybenzyl-protected maleimide precursor, which provided high specific activity [11C]SB-216763 in 1% noncorrected radiochemical yield (based upon [11C]CH3I) and 97–100% radiochemical purity (n = 7). Initial preclinical evaluation in rodent and nonhuman primate PET imaging studies revealed high initial brain uptake (peak rodent SUV = 2.5 @ 3 min postinjection; peak nonhuman primate SUV = 1.9 @ 5 min postinjection) followed by washout. Brain uptake was highest in thalamus, striatum, cortex, and cerebellum, areas known to be rich in GSK-3. These results make the arylindolemaleimide skeleton our lead scaffold for developing a PET radiotracer for quantification of GSK-3 density in vivo and ultimately translating it into clinical use. PMID:26005531

Applying Standard Independent Verification and Validation (IVV) Techniques Within an Agile Framework: Is There a Compatibility Issue?

NASA Technical Reports Server (NTRS)

Dabney, James B.; Arthur, James Douglas

2017-01-01

Agile methods have gained wide acceptance over the past several years, to the point that they are now a standard management and execution approach for small-scale software development projects. While conventional Agile methods are not generally applicable to large multi-year and mission-critical systems, Agile hybrids are now being developed (such as SAFe) to exploit the productivity improvements of Agile while retaining the necessary process rigor and coordination needs of these projects. From the perspective of Independent Verification and Validation (IVV), however, the adoption of these hybrid Agile frameworks is becoming somewhat problematic. Hence, we find it prudent to question the compatibility of conventional IVV techniques with (hybrid) Agile practices.This paper documents our investigation of (a) relevant literature, (b) the modification and adoption of Agile frameworks to accommodate the development of large scale, mission critical systems, and (c) the compatibility of standard IVV techniques within hybrid Agile development frameworks. Specific to the latter, we found that the IVV methods employed within a hybrid Agile process can be divided into three groups: (1) early lifecycle IVV techniques that are fully compatible with the hybrid lifecycles, (2) IVV techniques that focus on tracing requirements, test objectives, etc. are somewhat incompatible, but can be tailored with a modest effort, and (3) IVV techniques involving an assessment requiring artifact completeness that are simply not compatible with hybrid Agile processes, e.g., those that assume complete requirement specification early in the development lifecycle.

GaSbBi/GaSb quantum well laser diodes

NASA Astrophysics Data System (ADS)

Delorme, O.; Cerutti, L.; Luna, E.; Narcy, G.; Trampert, A.; Tournié, E.; Rodriguez, J.-B.

2017-05-01

We report on the structural and optical properties of GaSbBi single layers and GaSbBi/GaSb quantum well heterostructures grown by molecular beam epitaxy on GaSb substrates. Excellent crystal quality and room-temperature photoluminescence are achieved in both cases. We demonstrate laser operation from laser diodes with an active zone composed of three GaSb0.885Bi0.115/GaSb quantum wells. These devices exhibit continuous-wave lasing at 2.5 μm at 80 K, and lasing under pulsed operation at room-temperature near 2.7 μm.

Observations of Spin-Powered Pulsars with the AGILE Gamma-Ray Telescope

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pellizzoni, A.; Pilia, M.; Possenti, M.

2008-12-24

AGILE is a small gamma-ray astronomy satellite mission of the Italian Space Agency dedicated to high-energy astrophysics launched in 2007 April. It provides large sky exposure levels (> or approx. 10{sup 9} cm{sup 2} s per year on the Galactic Plane) with sensitivity peaking at E{approx}400 MeV(and simultaneous X-ray monitoring in the 18-60 keV band) where the bulk of pulsar energy output is typically released. Its {approx}1 {mu}s is absolute time tagging capability makes it perfectly suited for the study of gamma-ray pulsars following up on the CGRO/EGRET heritage. In this paper we summarize the timing results obtained during themore » first year of AGILE observations of the known gamma-ray pulsars Vela, Crab, Geminga and B 1706-4. AGILE collected a large number of gamma-ray photons from EGRET pulsars ({approx}10,000 pulsed counts for Vela) in only few months of observations unveiling new interesting features at sub-millisecond level in the pulsars' high-energy light-curves and paving the way to the discovery of new gamma-ray pulsars.« less

The Influence of Growth Temperature on Sb Incorporation in InAsSb, and the Temperature-dependent Impact of Bi Surfactants

DTIC Science & Technology

2014-01-01

resolution X - ray diffraction (XRD) were collected for all samples, and reciprocal space maps (RSMs) were collected from selected samples. The complete data...exposure. The lines represent the model fit. 19 13 Figure 1. Triple axis x - ray diffraction from the bi-layered InAsSb structures grown on GaSb at...Applied Physics, Structural properties of bismuth‐bearing semiconductor alloys, 63 (1988) 107. 18 12 Figure Captions Figure 1. Triple axis x - ray

AGILE integration into APC for high mix logic fab

NASA Astrophysics Data System (ADS)

Gatefait, M.; Lam, A.; Le Gratiet, B.; Mikolajczak, M.; Morin, V.; Chojnowski, N.; Kocsis, Z.; Smith, I.; Decaunes, J.; Ostrovsky, A.; Monget, C.

2015-09-01

For C040 technology and below, photolithographic depth of focus control and dispersion improvement is essential to secure product functionality. Critical 193nm immersion layers present initial focus process windows close to machine control capability. For previous technologies, the standard scanner sensor (Level sensor - LS) was used to map wafer topology and expose the wafer at the right Focus. Such optical embedded metrology, based on light reflection, suffers from reading issues that cannot be neglected anymore. Metrology errors are correlated to inspected product area for which material types and densities change, and so optical properties are not constant. Various optical phenomena occur across the product field during wafer inspection and have an effect on the quality and position of the reflected light. This can result in incorrect heights being recorded and exposures possibly being done out of focus. Focus inaccuracy associated to aggressive process windows on critical layers will directly impact product realization and therefore functionality and yield. ASML has introduced an air gauge sensor to complement the optical level sensor and lead to optimal topology metrology. The use of this new sensor is managed by the AGILE (Air Gauge Improved process LEveling) application. This measurement with no optical dependency will correct for optical inaccuracy of level sensor, and so improve best focus dispersion across the product. Due to the fact that stack complexity is more and more important through process steps flow, optical perturbation of standard Level sensor metrology is increasing and is becoming maximum for metallization layers. For these reasons AGILE feature implementation was first considered for contact and all metal layers. Another key point is that standard metrology will be sensitive to layer and reticle/product density. The gain of Agile will be enhanced for multiple product contribution mask and for complex System on Chip. Into ST context (High

Agile Preparation within a Traditional Project Management Course

ERIC Educational Resources Information Center

Landry, Jeffrey P.; McDaniel, Rachel

2016-01-01

Agile software approaches have seen a steady rise over a decade and a half, but agile's place in the information systems (IS) undergraduate curriculum is far from settled. While agile concepts may arguably be taught in multiple places in the IS curriculum, this paper argues for its inclusion in a project management course. This paper builds on…

Agile Methods for Open Source Safety-Critical Software

PubMed Central

Enquobahrie, Andinet; Ibanez, Luis; Cheng, Patrick; Yaniv, Ziv; Cleary, Kevin; Kokoori, Shylaja; Muffih, Benjamin; Heidenreich, John

2011-01-01

The introduction of software technology in a life-dependent environment requires the development team to execute a process that ensures a high level of software reliability and correctness. Despite their popularity, agile methods are generally assumed to be inappropriate as a process family in these environments due to their lack of emphasis on documentation, traceability, and other formal techniques. Agile methods, notably Scrum, favor empirical process control, or small constant adjustments in a tight feedback loop. This paper challenges the assumption that agile methods are inappropriate for safety-critical software development. Agile methods are flexible enough to encourage the right amount of ceremony; therefore if safety-critical systems require greater emphasis on activities like formal specification and requirements management, then an agile process will include these as necessary activities. Furthermore, agile methods focus more on continuous process management and code-level quality than classic software engineering process models. We present our experiences on the image-guided surgical toolkit (IGSTK) project as a backdrop. IGSTK is an open source software project employing agile practices since 2004. We started with the assumption that a lighter process is better, focused on evolving code, and only adding process elements as the need arose. IGSTK has been adopted by teaching hospitals and research labs, and used for clinical trials. Agile methods have matured since the academic community suggested they are not suitable for safety-critical systems almost a decade ago, we present our experiences as a case study for renewing the discussion. PMID:21799545

Physical demand of seven closed agility drills.

PubMed

Atkinson, Mark; Rosalie, Simon; Netto, Kevin

2016-11-01

The present study aimed to quantify the demand of seven generic, closed agility drills. Twenty males with experience in invasion sports volunteered to participate in this study. They performed seven, closed agility drills over a standardised 30-m distance. Physical demand measures of peak velocity, total foot contacts, peak impacts, completion time, and maximum heart rate were obtained via the use of wearable sensor technologies. A subjective rating of perceived exertion (RPE) was also obtained. All measures, with the exception of maximum heart rates and RPE were able to delineate drills in terms of physical and physiological demand. The findings of this study exemplify the differences in demand of agility-type movements. Drill demand was dictated by the type of agility movement initiated with the increase in repetitiveness of a given movement type also contributing to increased demand. Findings from this study suggest agility drills can be manipulated to vary physical and physiological demand. This allows for the optimal application of training principles such as overload, progression, and periodisation.

The Introduction of Agility into Albania.

ERIC Educational Resources Information Center

Smith-Stevens, Eileen J.; Shkurti, Drita

1998-01-01

Describes a plan to introduce and achieve a national awareness of agility (and easy entry into the world market) for Albania through the relatively stable higher-education order. Agility's four strategic principles are enriching the customer, cooperating to enhance competitiveness, organizing to master change and uncertainty, and leveraging the…

InGaAsSb/AlGaAsSb Heterojunction Phototransistors for Infrared Applications

NASA Technical Reports Server (NTRS)

Refaat, Tamer F.; Abedin, M. N.; Sulima, Oleg V.; Ismail, Syed; Singh, Upendra N.

2006-01-01

High quality infrared (IR) quantum detectors are important for several applications, such as atmospheric remote sensing, chemical detection and absorption spectroscopy. Although several IR detectors are commercially available, with different materials and structures, they provide limited performance regarding the signal-to-noise ratio and the corresponding minimum detectable signal. InGaAsSb/AlGaAsSb heterojunction based phototransistors show strong potential for developing IR sensors with improved performance. In this paper, the performance of a novel npn InGaAsSb/AlGaAsSb heterojunction phototransistor is presented. This performance study is based on experimental characterization of the device dark current, noise and spectral response. Detectivity of 1.7x10(exp 9) cmHz(exp 1/2)/W at 2 microns was obtained at 100 C temperature and 2 V bias voltage. This corresponds to a responsivity of 94.7 A/W and an internal gain of 156 with about 37.7% quantum efficiency. Reducing the temperature to -30 C allows to increase the bias to 3V and enhance the detectivity to 8.7x10(exp 10) cmHz(exp 1/2)/W at the same wavelength, which corresponds to a responsivity of 386.5 A/W and an internal gain of 288.2 with about 83.3% quantum efficiency. The device impulse response and linearity, including the corresponding dynamic range, also are presented. Impulse response analysis indicated a settling time of about 1.1 s at 2V and 100 C, while linearity measurements indicated a constant responsivity in the radiation intensity range of 1.6x10(exp -7) W/sq cm and 31.6 mW/sq cm.

Smart Mirrors for Photorefractive Control of Light with Tim Bunning, RX - Agile Filters Application

DTIC Science & Technology

2016-11-08

AFRL-AFOSR-UK-TR-2017-0008 Smart Mirrors for photorefractive control of light with Tim Bunning, RX-- Agile filters application Luciano De Sio...photorefractive control of light with Tim Bunning, RX-- Agile filters application 5a.  CONTRACT NUMBER 5b.  GRANT NUMBER FA9550-14-1-0050 5c.  PROGRAM...photorefractive, switchable optical filters , liquide crystalline composite materials, Switchable reflective holographic gratings, polymer-dispersed liquid

AGILE detection of a rebrightening of the gamma-ray source AGL J2251-1239

NASA Astrophysics Data System (ADS)

Piano, G.; Pittori, C.; Tavani, M.; Lucarelli, F.; Verrecchia, F.; Giommi, P.; Cardillo, M.; Ursi, A.; Minervini, G.; Bulgarelli, A.; Parmiggiani, N.; Vercellone, S.; Fioretti, V.; Pilia, M.; Donnarumma, I.; Gianotti, F.; Trifoglio, M.; Giuliani, A.; Mereghetti, S.; Caraveo, P.; Perotti, F.; Chen, A.; Argan, A.; Costa, E.; Del Monte, E.; Evangelista, Y.; Feroci, M.; Lazzarotto, F.; Lapshov, I.; Pacciani, L.; Soffitta, P.; Sabatini, S.; Vittorini, V.; Pucella, G.; Rapisarda, M.; Di Cocco, G.; Fuschino, F.; Galli, M.; Labanti, C.; Marisaldi, M.; Pellizzoni, A.; Trois, A.; Barbiellini, G.; Vallazza, E.; Longo, F.; Morselli, A.; Picozza, P.; Prest, M.; Lipari, P.; Zanello, D.; Cattaneo, P. W.; Rappoldi, A.; Ferrari, A.; Colafrancesco, S.; Paoletti, F.; Antonelli, A.; Salotti, L.; Valentini, G.; D'Amico, F.

2018-01-01

AGILE is detecting again intense gamma-ray emission above 100 MeV from a source at Galactic coordinates (l, b) = (54.6, -58.4) +/- 0.9 deg (95% stat. c.l.) +/- 0.1 deg (syst.) (R.A., Dec. (J2000): 342.26, -12.74 deg), compatible with AGL J2251-1239 reported in a flaring state by AGILE on December 8, 2017 (ATel #11043, F. Lucarelli et al.).

The orexin-1 receptor antagonist SB-334867 decreases anxiety-like behavior and c-Fos expression in the hypothalamus of rats exposed to cat odor.

PubMed

Vanderhaven, M W; Cornish, J L; Staples, L G

2015-02-01

Increasing evidence suggests that the orexin system is involved in modulating anxiety, and we have recently shown that cat odor-induced anxiety in rats is attenuated by the orexin receptor antagonist SB-334867. In the current experiment, c-Fos expression was used to map changes in neuronal activation following SB-334867 administration in the cat odor anxiety model. Male Wistar rats were exposed to cat odor with or without SB-334867 pre-treatment (10 mg/kg, i.p.). A naïve control group not exposed to cat odor was also used. Following cat odor exposure, brains were processed for c-Fos expression. Vehicle-treated rats showed an increase in anxiety-like behaviors (increased hiding and decreased approach toward the cat odor), and increased c-Fos expression in the posteroventral medial amygdala (MePV), paraventricular hypothalamus (PVN) and dorsal premammillary nucleus (PMd). In rats pretreated with SB-334867, approach scores increased and c-Fos expression decreased in the PVN and PMd. These results provide both behavioral and neuroanatomical evidence for the attenuation of cat odor-induced anxiety in rats via the orexin system. Crown Copyright © 2014. Published by Elsevier B.V. All rights reserved.

Unusual centrosymmetric structure of [M(18-crown-6)](+) (M = Rb, Cs and NH4) complexes stabilized in an environment of hexachloridoantimonate(V) anions.

PubMed

Ponomarova, Vira V; Rusanova, Julia A; Rusanov, Eduard B; Domasevitch, Konstantin V

2015-10-01

In (1,4,7,10,13,16-hexaoxacyclooctadecane)rubidium hexachloridoantimonate(V), [Rb(C12H24O6)][SbCl6], (1), and its isomorphous caesium {(1,4,7,10,13,16-hexaoxacyclooctadecane)caesium hexachloridoantimonate(V), [Cs(C12H24O6)][SbCl6]}, (2), and ammonium {ammonium hexachloridoantimonate(V)-1,4,7,10,13,16-hexaoxacyclooctadecane (1/1), (NH4)[SbCl6]·C12H24O6}, (3), analogues, the hexachloridoantimonate(V) anions and 18-crown-6 molecules reside across -3 axes passing through the Sb atoms and the centroids of the 18-crown-6 groups, both of which coincide with centres of inversion. The Rb(+) [in (1)], Cs(+) [in (2)] and NH4(+) [in (3)] cations are situated inside the cavity of the 18-crown-6 ring; they are situated on -3 axes and are equally disordered about centres of inversion, deviating from the centroid of the 18-crown-6 molecule by 0.4808 (13), 0.9344 (7) and 0.515 (8) Å, respectively. Interaction of the ammonium cation and the 18-crown-6 group is supported by three equivalent hydrogen bonds [N...O = 2.928 (3) Å and N-H...O = 162°]. The centrosymmetric structure of [Cs(18-crown-6)](+), with the large Cs(+) cation approaching the centre of the ligand cavity, is unprecedented and accompanied by unusually short Cs-O bonds [2.939 (2) and 3.091 (2) Å]. For all three compounds, the [M(18-crown-6)](+) cations and [SbCl6](-) anions afford linear stacks along the c axis, with the cationic complexes embedded between pairs of inversion-related anions.

High energy variability of 3C 273 during the AGILE multiwavelength campaign of December 2007-January 2008

NASA Astrophysics Data System (ADS)

Pacciani, L.; Donnarumma, I.; Vittorini, V.; D'Ammando, F.; Fiocchi, M. T.; Impiombato, D.; Stratta, G.; Verrecchia, F.; Bulgarelli, A.; Chen, A. W.; Giuliani, A.; Longo, F.; Pucella, G.; Vercellone, S.; Tavani, M.; Argan, A.; Barbiellini, G.; Boffelli, F.; Caraveo, P. A.; Cattaneo, P. W.; Cocco, V.; Costa, E.; Del Monte, E.; Di Cocco, G.; Evangelista, Y.; Feroci, M.; Froysland, T.; Fuschino, F.; Galli, M.; Gianotti, F.; Labanti, C.; Lapshov, I.; Lazzarotto, F.; Lipari, P.; Marisaldi, M.; Mereghetti, S.; Morselli, A.; Pellizzoni, A.; Perotti, F.; Picozza, P.; Prest, M.; Rapisarda, M.; Soffitta, P.; Trifoglio, M.; Tosti, G.; Trois, A.; Vallazza, E.; Zanello, D.; Antonelli, L. A.; Colafrancesco, S.; Cutini, S.; Gasparrini, D.; Giommi, P.; Pittori, C.; Salotti, L.

2009-01-01

Context: We report the results of a 3-week multi-wavelength campaign targeting the flat spectrum radio quasar 3C 273 carried out with the AGILE gamma-ray mission, covering the 30 MeV-50 GeV and 18-60 keV, the REM observatory (covering the near-IR and optical), Swift (near-UV/Optical, 0.2-10 keV and 15-50 keV), INTEGRAL (3-200 keV) and Rossi XTE (2-12 keV). This is the first observational campaign including gamma-ray data, after the last EGRET observations, more than 8 years ago. Aims: This campaign has been organized by the AGILE team with the aim of observing, studying and modelling the broad band energy spectrum of the source, and its variability on a week timescale, testing the emission models describing the spectral energy distribution of this source. Methods: Our study was carried out using simultaneous light curves of the source flux from all the involved instruments, in the different energy ranges, to search for correlated variability. Then a time-resolved spectral energy distribution was used for a detailed physical modelling of the emission mechanisms. Results: The source was detected in gamma-rays only in the second week of our campaign, with a flux comparable to the level detected by EGRET in June 1991. We found an indication of a possible anti-correlation between the emission at gamma-rays and at soft and hard X-rays, supported by the complete set of instruments. Instead, optical data do not show short term variability, as expected for this source. Only in two preceding EGRET observations (in 1993 and 1997) 3C 273 showed intra-observation variability in gamma-rays. In the 1997 observation, flux variation in gamma-rays was associated with a synchrotron flare. The energy-density spectrum with almost simultaneous data partially covers the regions of synchrotron emission, the big blue bump, and the inverse-Compton. We adopted a leptonic model to explain the hard X/gamma-ray emissions, although from our analysis hadronic models cannot be ruled out. In the

A Roadmap for Using Agile Development in a Traditional Environment

NASA Technical Reports Server (NTRS)

Streiffert, Barbara A.; Starbird, Thomas; Grenander, Sven

2006-01-01

One of the newer classes of software engineering techniques is called 'Agile Development'. In Agile Development software engineers take small implementation steps and, in some cases they program in pairs. In addition, they develop automatic tests prior to implementing their small functional piece. Agile Development focuses on rapid turnaround, incremental planning, customer involvement and continuous integration. Agile Development is not the traditional waterfall method or even a rapid prototyping method (although this methodology is closer to Agile Development). At Jet Propulsion Laboratory (JPL) a few groups have begun Agile Development software implementations. The difficulty with this approach becomes apparent when Agile Development is used in an organization that has specific criteria and requirements handed down for how software development is to be performed. The work at the JPL is performed for the National Aeronautics and Space Agency (NASA). Both organizations have specific requirements, rules and procedure for developing software. This paper will discuss the some of the initial uses of the Agile Development methodology, the spread of this method and the current status of the successful incorporation into the current JPL development policies.

Perspectives on Agile Coaching

NASA Astrophysics Data System (ADS)

Fraser, Steven; Lundh, Erik; Davies, Rachel; Eckstein, Jutta; Larsen, Diana; Vilkki, Kati

There are many perspectives to agile coaching including: growing coaching expertise, selecting the appropriate coach for your context; and eva luating value. A coach is often an itinerant who may observe, mentor, negotiate, influence, lead, and/or architect everything from team organization to system architecture. With roots in diverse fields ranging from technology to sociology coaches have differing motivations and experience bases. This panel will bring together coaches to debate and discuss various perspectives on agile coaching. Some of the questions to be addressed will include: What are the skills required for effective coaching? What should be the expectations for teams or individu als being coached? Should coaches be: a corporate resource (internal team of consultants working with multiple internal teams); an integral part of a specific team; or external contractors? How should coaches exercise influence and au thority? How should management assess the value of a coaching engagement? Do you have what it takes to be a coach? - This panel will bring together sea soned agile coaches to offer their experience and advice on how to be the best you can be!

MOVPE prepared InAs/GaAs quantum dots covered by GaAsSb layer with long wavelength emission at 1.8 μm

NASA Astrophysics Data System (ADS)

Zíková, Markéta; Hospodková, Alice; Pangrác, Jiří; Oswald, Jiří; Krčil, Pavel; Hulicius, Eduard; Komninou, Philomela; Kioseoglou, Joseph

2015-03-01

Preparation and properties of InAs/GaAs quantum dots (QDs) prepared by the MOVPE technology covered by GaAsSb strain reducing layer (SRL) with extremely long emission wavelength at 1.8 μm will be presented. Increase of the emission wavelength was achieved by the introduction of GaAsSb SRL with Sb content of about 30% in the solid phase. The high Sb concentration in the SRL causes the preservation of QD size, which is about 15 nm wide at the base and 5 nm high. Increased QD size increases the photoluminescence (PL) wavelength. Furthermore, high content of antimony leads to a creation of type II heterostructure for which a redshift of the PL wavelength and decrease of the PL intensity are typical. Low PL intensity may complicate light emitting applications; however fast separation of carriers in the type II structure is an advantage for detector or solar cell application, especially with the long working wavelength. With respect to the perspective application of this structure, the photocurrent (PC) measurement was chosen as the complementary characterization method. A depression of PC for quantum well wavelength region (approximately 900-1200 nm) was observed for positive bias, while the PC from QDs (over 1200 nm) is not sensitive to the electric field orientation at all. An explanation of this unexpected phenomenon is suggested.

Agile Mcal, the Mini-Calorimeter

NASA Astrophysics Data System (ADS)

Bastia, Paolo; Poulsen, Jens Michael; Monzani, Franco; Radaelli, Paolo; Marchesi, Paolo; Labanti, Claudio; Marisaldi, Martino; Fuschino, Fabio; Bulgarelli, Andrea

2006-04-01

AGILE is a scientific mission dedicated to gamma-ray astrophysics in space, and the mini-calorimeter MCAL is one of four detector systems on the satellite. The MCAL instrument is sensitive in the energy range: 300 keV - 100 MeV. It has two main functions: one autonomous mode for detection of impulsive cosmic events and the other as “a slave” supporting the energy measurements of the pair-conversion tracker. The AGILE Small Mission is funded by the Italian Space Agency (ASI), and the INAF-IASF section at Bologna has the scientific responsibility for MCAL. LABEN develops the MCAL instrument with its detectors and electronics. This paper gives an overview of the detectors on AGILE, and then it gives details on the design of MCAL, and finally we report on the tests at instrument level.

High-temperature luminescence in an n-GaSb/n-InGaAsSb/p-AlGaAsSb light-emitting heterostructure with a high potential barrier

DOE Office of Scientific and Technical Information (OSTI.GOV)

Petukhov, A. A., E-mail: andrey-rus29@rambler.ru; Zhurtanov, B. E.; Kalinina, K. V.

2013-09-15

The electroluminescent properties of an n-GaSb/n-InGaAsSb/p-AlGaAsSb heterostructure with a high potential barrier in the conduction band (large conduction-band offset) at the n-GaSb/n-InGaAsSb type-II heterointerface ({Delta}E{sub c} = 0.79 eV) are studied. Two bands with peaks at 0.28 and 0.64 eV at 300 K, associated with radiative recombination in n-InGaAsSb and n-GaSb, respectively, are observed in the electroluminescence (EL) spectrum. In the entire temperature range under study, T = 290-480 K, additional electron-hole pairs are formed in the n-InGaAsSb active region by impact ionization with hot electrons heated as a result of the conduction-band offset. These pairs contribute to radiative recombination,more » which leads to a nonlinear increase in the EL intensity and output optical power with increasing pump current. A superlinear increase in the emission power of the long-wavelength band is observed upon heating in the temperature range T = 290-345 K, and a linear increase is observed at T > 345 K. This work for the first time reports an increase in the emission power of a light-emitting diode structure with increasing temperature. It is shown that this rise is caused by a decrease in the threshold energy of the impact ionization due to narrowing of the band gap of the active region.« less

Agile Systems Engineering-Kanban Scheduling Subsection

DTIC Science & Technology

2017-03-10

including both online and standalone versions. RESEARCH GOALS The overall Agile SE Management Project research goals are to: 1. Identify agile...March 10, 2017 5 Establish a better technical project management and... Project Management ,” Master of Science Project , Stevens Institute, to be completed in May, 2017. • Smith, Jeffrey, “System of Systems Task

Agile Manifesto for Teaching and Learning

ERIC Educational Resources Information Center

Krehbiel, Timothy C.; Salzarulo, Peter A.; Cosmah, Michelle L.; Forren, John; Gannod, Gerald; Havelka, Douglas; Hulshult, Andrea R.; Merhout, Jeffrey

2017-01-01

A group of faculty members representing six colleges at a public university formed a learning community to study the Agile Way of Working--a method of workplace collaboration widely used in software development--and to determine whether the concepts, practices, and benefits of Agile are applicable to higher education settings. After more than two…

Highly efficient and mild electrochemical mineralization of long-chain perfluorocarboxylic acids (C9-C10) by Ti/SnO2-Sb-Ce, Ti/SnO2-Sb/Ce-PbO2, and Ti/BDD electrodes.

PubMed

Lin, Hui; Niu, Junfeng; Xu, Jiale; Huang, Haiou; Li, Duo; Yue, Zhihan; Feng, Chenghong

2013-11-19

The electrochemical mineralization of environmentally persistent long-chain perfluorinated carboxylic acids (PFCAs), i.e., perfluorononanoic acid (C8F17COOH, PFNA) and perfluorodecanoic acid (C9F19COOH, PFDA) was investigated in aqueous solutions (0.25 mmol L(-1)) over Ti/SnO2-Sb-Ce (SnO2), Ti/SnO2-Sb/Ce-PbO2 (PbO2), and Ti/BDD (BDD) anodes under galvanostatic control at room temperature. Based on PFCA decay rate, total organic carbon (TOC) reduction, defluorination ratio, safety, and energy consumption, the performance of PbO2 electrode was comparable with that of BDD electrode. After 180 min electrolysis, the PFNA removals on BDD and PbO2 electrodes were 98.7 ± 0.4% and 97.1 ± 1.0%, respectively, while the corresponding PFDA removals were 96.0 ± 1.4% and 92.2 ± 1.9%. SnO2 electrode yielded lower PFCA removals and led to notable secondary pollution by Sb ions. The primary mineralization product, F(-), as well as trace amounts of intermediate PFCAs with shortened chain lengths, were detected in aqueous solution after electrolysis. On the basis of these results, a degradation mechanism including three potential routes is proposed: via formation of short-chain PFCAs by stepwise removal of CF2; direct mineralization to CO2 and HF; conversion to volatile fluorinated organic compounds. The results presented here demonstrate that electrochemical technique exhibits high efficiency in mineralizing PFNA and PFDA under mild conditions, and is promising for the treatment of long-chain PFCAs in wastewater.

40 CFR 721.10297 - Tin, C16-18 and C18-unsatd. fatty acids castor-oil fatty acids complexes.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Tin, C16-18 and C18-unsatd. fatty... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10297 Tin, C16-18 and C18-unsatd... to reporting. (1) The chemical substance identified as tin, C16-18 and C18-unsatd. fatty acids castor...

40 CFR 721.10297 - Tin, C16-18 and C18-unsatd. fatty acids castor-oil fatty acids complexes.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Tin, C16-18 and C18-unsatd. fatty... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10297 Tin, C16-18 and C18-unsatd... to reporting. (1) The chemical substance identified as tin, C16-18 and C18-unsatd. fatty acids castor...

40 CFR 721.10297 - Tin, C16-18 and C18-unsatd. fatty acids castor-oil fatty acids complexes.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Tin, C16-18 and C18-unsatd. fatty... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10297 Tin, C16-18 and C18-unsatd... to reporting. (1) The chemical substance identified as tin, C16-18 and C18-unsatd. fatty acids castor...

Test Methods for Robot Agility in Manufacturing.

PubMed

Downs, Anthony; Harrison, William; Schlenoff, Craig

2016-01-01

The paper aims to define and describe test methods and metrics to assess industrial robot system agility in both simulation and in reality. The paper describes test methods and associated quantitative and qualitative metrics for assessing robot system efficiency and effectiveness which can then be used for the assessment of system agility. The paper describes how the test methods were implemented in a simulation environment and real world environment. It also shows how the metrics are measured and assessed as they would be in a future competition. The test methods described in this paper will push forward the state of the art in software agility for manufacturing robots, allowing small and medium manufacturers to better utilize robotic systems. The paper fulfills the identified need for standard test methods to measure and allow for improvement in software agility for manufacturing robots.

Future Research in Agile Systems Development: Applying Open Innovation Principles Within the Agile Organisation

NASA Astrophysics Data System (ADS)

Conboy, Kieran; Morgan, Lorraine

A particular strength of agile approaches is that they move away from ‘introverted' development and intimately involve the customer in all areas of development, supposedly leading to the development of a more innovative and hence more valuable information system. However, we argue that a single customer representative is too narrow a focus to adopt and that involvement of stakeholders beyond the software development itself is still often quite weak and in some cases non-existent. In response, we argue that current thinking regarding innovation in agile development needs to be extended to include multiple stakeholders outside the business unit. This paper explores the intra-organisational applicability and implications of open innovation in agile systems development. Additionally, it argues for a different perspective of project management that includes collaboration and knowledge-sharing with other business units, customers, partners, and other relevant stakeholders pertinent to the business success of an organisation, thus embracing open innovation principles.

Quantitative high-throughput determination of endogenous retinoids in human plasma using triple-stage liquid chromatography/tandem mass spectrometry.

PubMed

Gundersen, Thomas E; Bastani, Nasser E; Blomhoff, Rune

2007-01-01

A high-throughput ultrasensitive analytical method based on liquid chromatography with positive ion atmospheric pressure chemical ionization (APCI) coupled to tandem mass spectrometric detection (LC/MS/MS) was developed for the determination of all-trans-4-oxo-retinoic acid (at4oxoRA), 13-cis-4-oxo-retinoic acid (13c4oxoRA), 13-cis-retinoic acid (13cRA), all-trans-retinoic acid (atRA) and all-trans-retinol (atROH) in human plasma. A stable isotope of atRA was used as internal standard (IS). The analytes and IS were isolated from 100 microL plasma by acetonitrile mono-phase extraction (MPE) performed in black 96-well microtiterplates. A 100 microL injection was focused on-column and chromatographed on an Agilent ZORBAX SB-C18 rapid-resolution high-throughput (RRHT) column with 1.8-microm particles (4.6 mmx50 mm) maintained at 60 degrees C. The initial mobile phase composition was acetonitrile/water/formic acid (10:90:0.1, v/v/v) delivered at 1.8 mL/min. Elution was accomplished by a fast gradient to acetonitrile/methanol/formic acid (90:10:0.1, v/v/v). The method had a chromatographic total run time of 7 min. An Applied Biosystems 4000 Q TRAP linear tandem mass spectrometer equipped with a heated nebulizer (APCI) ionization source was operated in multiple reaction monitoring (MRM) mode with the precursor-to-product ion transitions m/z 315.4-->297 (4-oxo-retinoic acids), 301.2-->205 (retinoic acids), 305.0-->209 (IS) and 269.2-->93 (retinol) used for quantification. The assay was fully validated and found to have acceptable accuracy, precision, linearity, sensitivity and selectivity. The mean extraction recoveries from spiked plasma samples were 80-105% for the various retinoids at three different levels. The intra-day accuracy of the assay was within 8% of nominal and intra-day precision was better than 8% coefficient of variance (CV) for retinoic acids. Inter-day precision results for quality control samples run over a 12-day period alongside clinical samples

Rapid quantification of resveratrol in mouse plasma by ultra high pressure liquid chromatography (UPLC) coupled to tandem mass spectrometry.

PubMed

Castillo-Pichardo, Linette; Dharmawardhane, Suranganie; Rodríguez-Orengo, José F

2014-12-01

The objective of this study was to develop a rapid and sensitive method for the quantification of resveratrol, a polyphenolic compound with multiple health beneficial effects, in mouse plasma. We used reversed-phase ultra high pressure-liquid chromatography with tandem mass spectrometry detection for the determination of resveratrol levels in mouse plasma. An Agilent Zorbax Eclipse Plus C18 column (2.1 mm x 50 mm, 1.8 μm) was used as the stationary phase. The mobile phase consisted of a gradient formed using 1 mM ammonium fluoride and methanol. Using this improved method, we obtained a retention time of 2.2 min and a total run time of 5 min, for resveratrol. The calibration curve for resveratrol showed a linear range from 0.5 to 100 ng/mL. The average coefficient of variation was 6% for interday variation and 4% for intraday variation. The recovery for resveratrol in mouse plasma was 85 ± 10% (mean ± standard deviation). The method presented herein allows a rapid and very sensitive quantification of resveratrol in mouse plasma at concentrations as low as 500 ppt.

A Roadmap for Using Agile Development in a Traditional Environment

NASA Technical Reports Server (NTRS)

Streiffert, Barbara; Starbird, Thomas; Grenander, Sven

2006-01-01

One of the newer classes of software engineering techniques is called 'Agile Development'. In Agile Development software engineers take small implementation steps and, in some cases, they program in pairs. In addition, they develop automatic tests prior to implementing their small functional piece. Agile Development focuses on rapid turnaround, incremental planning, customer involvement and continuous integration. Agile Development is not the traditional waterfall method or even a rapid prototyping method (although this methodology is closer to Agile Development). At the Jet Propulsion Laboratory (JPL) a few groups have begun Agile Development software implementations. The difficulty with this approach becomes apparent when Agile Development is used in an organization that has specific criteria and requirements handed down for how software development is to be performed. The work at the JPL is performed for the National Aeronautics and Space Agency (NASA). Both organizations have specific requirements, rules and processes for developing software. This paper will discuss some of the initial uses of the Agile Development methodology, the spread of this method and the current status of the successful incorporation into the current JPL development policies and processes.

In-plane electrical transport in n-type selectively doped GaSb/AlGaSb multiquantum wells

NASA Astrophysics Data System (ADS)

Ghezzi, C.; Cioce, B.; Magnanini, R.; Parisini, A.

2001-11-01

Results are reported regarding in-plane electrical transport in n-type selectively doped GaSb/AlGaSb multiquantum wells. In the samples, which were grown by molecular beam epitaxy, only the central regions of the Al0.40Ga0.60Sb barriers were Te doped. Low-field, low-temperature Hall measurements in the dark demonstrated the presence in the GaSb wells of a degenerate electron gas with nonzero occupancy only for the lowest miniband. A positive persistent photoconductivity effect, related to the DX character of the Te impurity, was also observed. This behavior enabled the μ electron mobility to be measured at T=10 K as a function of the nS sheet carrier density. Since the experimental data were consistent with a dominant role of the interface roughness scattering in the limiting of μ, the height, Δ, and the lateral size, Λ, of the interface roughness were determined from the analysis of the μ=μ(nS) dependence. Acceptable values of Δ were obtained, consistent with results of structural investigations in single quantum well samples of GaSb/Al0.40Ga0.60Sb [E. Kh. Mukhamedzhanov, C. Bocchi, S. Franchi, A. Baraldi, R. Magnanini, and L. Nasi, J. Appl. Phys. 87, 4234 (2000)].

Inserting Agility in System Development

DTIC Science & Technology

2012-07-01

Agile IT Acquisition, IT Box, Scrum Inserting Agility in System Development Matthew R. Kennedy and Lt Col Dan Ward, USAF With the fast-paced nature...1,700 individuals and 71 countries, found Scrum and eXtreme Programming to be the most widely followed method- ologies (VersionOne, 2007). Other...University http://www.dau.mil 259 Defense ARJ, July 2012, Vol. 19 No. 3 : 249–264 Scrum Scrum is a framework used for project management, which is

Search of GRB with AGILE Minicalorimeter

NASA Astrophysics Data System (ADS)

Fuschino, F.; Labanti, C.; Galli, M.; Marisaldi, M.; Bulgarelli, A.; Gianotti, F.; Trifoglio, M.; Argan, A.; Del Monte, E.; Donnarumma, I.; Feroci, M.; Lazzarotto, F.; Pacciani, L.; Tavani, M.; Trois, A.

2008-04-01

AGILE, the small scientific mission of the Italian Space Agency devoted to Hard-X and Gamma-ray astrophysics, was successfully launched on April 23, 2007. The AGILE payload is composed of a tungsten-silicon tracker (ST), operating in the gamma-ray energy range 30 MeV 50 GeV; Super-AGILE, an X-ray imager operating in the energy range 15 45 keV; the Minicalorimeter (MCAL) and an Anticoincidence shield. MCAL is a detector of about 1400 cm2 sensitive in the range 0.3 200 MeV, that can be used both as a slave of the ST to contribute to the AGILE Gamma Ray imaging Detector (GRID operative mode) and autonomously for detection of transient events (BURST operative mode). MCAL is made of 30 CsI(Tl) bar-shaped scintillation detectors with photodiode readout at both ends, arranged in two orthogonal layers. Energy and position of interaction can be derived from a proper composition of the signals readout at the bar's ends, absolute time tagging can be achieved with a μs resolution. The Burst logic deals with various rate-meters on different time scales, energy bands, and MCAL spatial zones. Different algorithms can be chosen for Burst triggering considering also the contribution of other detectors like Super AGILE. In this paper the various trigger logic will be reviewed as well as their on-ground test performed with a dedicated experimental setup.

Test Methods for Robot Agility in Manufacturing

PubMed Central

Downs, Anthony; Harrison, William; Schlenoff, Craig

2017-01-01

Purpose The paper aims to define and describe test methods and metrics to assess industrial robot system agility in both simulation and in reality. Design/methodology/approach The paper describes test methods and associated quantitative and qualitative metrics for assessing robot system efficiency and effectiveness which can then be used for the assessment of system agility. Findings The paper describes how the test methods were implemented in a simulation environment and real world environment. It also shows how the metrics are measured and assessed as they would be in a future competition. Practical Implications The test methods described in this paper will push forward the state of the art in software agility for manufacturing robots, allowing small and medium manufacturers to better utilize robotic systems. Originality / value The paper fulfills the identified need for standard test methods to measure and allow for improvement in software agility for manufacturing robots. PMID:28203034

Crystal growth and physical properties of SrCu2As2, SrCu2Sb2, and BaCu2Sb2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anand, V.K.; Perera, P. Kanchana; Pandey, Abhishek

2012-06-25

We report the growth of single crystals of SrCu2As2, SrCu2Sb2, SrCu2(As0.84Sb0.16)2, and BaCu2Sb2 using the self-flux technique and their structural, magnetic, thermal, and transport properties that were investigated by powder x-ray diffraction (XRD), magnetic susceptibility χ, specific heat Cp, and electrical resistivity ρ measurements versus temperature T from 1.8 to 350 K. Rietveld refinements of XRD patterns for crushed crystals confirm that SrCu2As2 crystallizes in the ThCr2Si2-type body-centered tetragonal structure (space group I4/mmm) and SrCu2Sb2 crystallizes in the CaBe2Ge2-type primitive tetragonal structure (space group P4/nmm). However, as reported previously, BaCu2Sb2 is found to have a large unit cell consisting ofmore » three blocks. Here a ThCr2Si2-type block is sandwiched between two CaBe2Ge2-type blocks along the c axis with an overall symmetry of I4/mmm, as reported, but likely with a monoclinic distortion. The χ data of all these compounds are diamagnetic and reveal nearly T-independent anisotropic behavior. The χ of SrCu2As2 is found to be larger in the ab plane than along the c axis, as also previously reported for pure and doped BaFe2As2, whereas the χ values of SrCu2Sb2 and BaCu2Sb2 are larger along the c axis. This difference in anisotropy appears to arise from the differences between the crystal structures. The finite values of the Sommerfeld linear specific heat coefficients γ and the T dependences of ρ reveal metallic character of all four compounds. The electronic and magnetic properties indicate that these compounds are sp metals with Cu in the nonmagnetic 3d10 electronic configuration corresponding to the oxidation state Cu+1, as previously predicted theoretically for SrCu2As2 by Singh [ Phys. Rev. B 79 153102 (2009)]. We present a brief review of theoretical and experimental work on the doping character of transition metals for Fe in BaFe2As2. The As–As covalent interlayer bond distances in the collapsed-tetragonal (Ca

Agility assessment using fuzzy logic approach: a case of healthcare dispensary.

PubMed

Suresh, M; Patri, Rojalin

2017-06-09

Agile concepts are not only beneficial for manufacturing sector but also for service sector such as healthcare. However, assessment of agility has been predominantly done in manufacturing enterprises. This study demonstrates a means to measure agility of a healthcare organization by assessing agility of a university dispensary. Its contribution to the knowledge base is twofold. First, it proposes a means to measure the agility of a healthcare organization and second, it identifies the attributes that prevent agile performance and outlines the suggestive measure to enhance its agile capabilities. A case study approach has been adopted and fuzzy logic has been employed to measure the agility of the case dispensary. At first, the measures of assessment which include four enablers, fifteen criteria and forty-five attributes have been identified from the literature and rated by the experts indicating the importance of the measures in the assessment. Then, the case dispensary has been assessed on those measures by collecting observed performance rating from decision makers. At last, Fuzzy logic has been applied on the performance rating data to analyze and interpret the agile capability of the dispensary. The findings suggest that transparent information flow, adequate salary and bonuses for caregivers, reading error in medical descriptions, in house/nearby pathology laboratory services, technical up-gradation of dispensary equipments and facilities, minimization of patient throughput time and adequate training programme for safety practices are the attributes that weakens agile capability of the University dispensary. The current agility of the dispensary was found to be 'Agile' which is average in relation to the agility labels. Attributes such as transparent information flow, adequate salary and bonuses for caregivers, elimination of reading error in medical descriptions, in house/nearby pathology laboratory services, technical up-gradation of dispensary equipments

AGILE detection of gamma-ray emission from the FSRQ Ton 0599

NASA Astrophysics Data System (ADS)

Bulgarelli, A.; Parmiggiani, N.; Lucarelli, F.; Verrecchia, F.; Pittori, C.; Tavani, M.; Vercellone, S.; Colafrancesco, S.; Cardillo, M.; Piano, G.; Ursi, A.; Fioretti, V.; Pilia, M.; Donnarumma, I.; Gianotti, F.; Trifoglio, M.; Giuliani, A.; Mereghetti, S.; Caraveo, P.; Perotti, F.; Chen, A.; Argan, A.; Costa, E.; Del Monte, E.; Evangelista, Y.; Feroci, M.; Lazzarotto, F.; Lapshov, I.; Pacciani, L.; Soffitta, P.; Sabatini, S.; Vittorini, V.; Pucella, G.; Rapisarda, M.; Di Cocco, G.; Fuschino, F.; Galli, M.; Labanti, C.; Marisaldi, M.; Pellizzoni, A.; Trois, A.; Barbiellini, G.; Vallazza, E.; Longo, F.; Morselli, A.; Picozza, P.; Prest, M.; Lipari, P.; Zanello, D.; Cattaneo, P. W.; Rappoldi, A.; Ferrari, A.; Paoletti, F.; Antonelli, A.; Giommi, P.; Salotti, L.; Valentini, G.; D'Amico, F.

2017-12-01

AGILE is detecting increasing gamma-ray emission above 100 MeV from a source positionally consistent with the FSRQ Ton 0599. Integrating from 2017-12-16 05:45 to 2017-12-18 05:45 UT, a preliminary maximum likelihood analysis yields a detection above 5 sigma and a flux F(E > 100 MeV)=(2.0 +/- 0.6) x 10^-6 ph cm^-2 s^-1.

Temperature dependent lattice constant of InSb above room temperature

NASA Astrophysics Data System (ADS)

Breivik, Magnus; Nilsen, Tron Arne; Fimland, Bjørn-Ove

2013-10-01

Using temperature dependent X-ray diffraction on two InSb single crystalline substrates, the bulk lattice constant of InSb was determined between 32 and 325 °C. A polynomial function was fitted to the data: a(T)=6.4791+3.28×10-5×T+1.02×10-8×T2 Å (T in °C), which gives slightly higher values than previously published (which go up to 62 °C). From the fit, the thermal expansion of InSb was calculated to be α(T)=5.062×10-6+3.15×10-9×T K-1 (T in °C). We found that the thermal expansion coefficient is higher than previously published values above 100 °C (more than 10% higher at 325 °C).

Peridigm summary report : lessons learned in development with agile components.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Salinger, Andrew Gerhard; Mitchell, John Anthony; Littlewood, David John

2011-09-01

This report details efforts to deploy Agile Components for rapid development of a peridynamics code, Peridigm. The goal of Agile Components is to enable the efficient development of production-quality software by providing a well-defined, unifying interface to a powerful set of component-based software. Specifically, Agile Components facilitate interoperability among packages within the Trilinos Project, including data management, time integration, uncertainty quantification, and optimization. Development of the Peridigm code served as a testbed for Agile Components and resulted in a number of recommendations for future development. Agile Components successfully enabled rapid integration of Trilinos packages into Peridigm. A cost of thismore » approach, however, was a set of restrictions on Peridigm's architecture which impacted the ability to track history-dependent material data, dynamically modify the model discretization, and interject user-defined routines into the time integration algorithm. These restrictions resulted in modifications to the Agile Components approach, as implemented in Peridigm, and in a set of recommendations for future Agile Components development. Specific recommendations include improved handling of material states, a more flexible flow control model, and improved documentation. A demonstration mini-application, SimpleODE, was developed at the onset of this project and is offered as a potential supplement to Agile Components documentation.« less

[Simultaneous determination of 9 ultraviolet stabilizers in food plastic packaging materials by solid phase extraction-high performance liquid chromatography].

PubMed

Zhang, Juzhou; Li, Jing; Shao, Dongliang; Yao, Bangben; Jiang, Junshu

2012-02-01

An effective high performance liquid chromatographic (HPLC) method has been developed for the simultaneous determination of 9 ultraviolet stabilizers in food plastic packaging materials. The food packaging samples were firstly extracted by methanol-ethyl acetate, and then purified by a C18 solid-phase extraction (SPE) column. The target compounds were separated on a ZORBAX SB-C18 column (250 mm x 4.6 mm, 5 microm) in gradient elution mode using methanol and water as mobile phases. The detection wavelength was at 310 nm. The linear plots of the nine ultraviolet stabilizers were obtained between 0.2 and 10 mg/L, with the correlation coefficients of above 0. 999 for the nine ultraviolet stabilizers. The limits of detection for this method were in the range from 0.05 to 0.1 mg/L. The recoveries spiked in commercial food plastic packaging materials were in the range of 70.2% - 89.0% with the relative standard deviations of 0.4% - 4.5%. The results indicated that the method is simple, accurate, and suitable for the simultaneous determination of the nine ultraviolet stabilizers in food plastic packaging materials.

Agile Methods: Selected DoD Management and Acquisition Concerns

DTIC Science & Technology

2011-10-01

SIDRE Software Intensive Innovative Development and Reengineering/Evolution SLIM Software Lifecycle Management -Estimate SLOC source lines of code...ISBN #0321502752 Coaching Agile Teams Lyssa Adkins ISBN #0321637704 Agile Project Management : Creating Innovative Products – Second Edition Jim...Accessed July 13, 2011. [Highsmith 2009] Highsmith, J. Agile Project Management : Creating Innovative Products, 2nd ed. Addison- Wesley, 2009

The polarization of Sb overlayers on NiMnSb(100)

NASA Astrophysics Data System (ADS)

Komesu, Takashi; Borca, C. N.; Jeong, Hae-Kyung; Dowben, P. A.; Ristoiu, Delia; Nozières, J. P.; Stadler, Shane; Idzerda, Y. U.

2000-08-01

We have investigated the induced polarization of paramagnetic Sb overlayers on the Heusler alloy NiMnSb. From combined X-ray absorption spectroscopy (XAS) and spin-polarized inverse photoemission spectroscopy (SPIPES), we can assign some of the unoccupied states of the Heusler alloy NiMnSb. With increasing thickness of the Sb overlayer, there is a decline in the density of states near the Fermi energy, as expected for a semimetal overlayer on a metallic substrate. While the Sb is polarized by the ferromagnetic NiMnSb substrate, consistent with the expectations of mean field theory, the polarization at the center of the surface/overlayer Brillouin zone cannot be easily related to the induced magnetization.

Laterality and performance of agility-trained dogs.

PubMed

Siniscalchi, Marcello; Bertino, Daniele; Quaranta, Angelo

2014-01-01

Correlations between lateralised behaviour and performance were investigated in 19 agility-trained dogs (Canis familiaris) by scoring paw preference to hold a food object and relating it to performance during typical agility obstacles (jump/A-frame and weave poles). In addition, because recent behavioural studies reported that visual stimuli of emotional valence presented to one visual hemifield at a time affect visually guided motor responses in dogs, the possibility that the position of the owner respectively in the left and in the right canine visual hemifield might be associated with quality of performance during agility was considered. Dogs' temperament was also measured by an owner-rated questionnaire. The most relevant finding was that agility-trained dogs displayed longer latencies to complete the obstacles with the owner located in their left visual hemifield compared to the right. Interestingly, the results showed that this phenomenon was significantly linked to both dogs' trainability and the strength of paw preference.

Distilling Design Patterns From Agile Curation Case Studies

NASA Astrophysics Data System (ADS)

Benedict, K. K.; Lenhardt, W. C.; Young, J. W.

2016-12-01

In previous work the authors have argued that there is a need to take a new look at the data management lifecycle. Our core argument is that the data management lifecycle needs to be in essence deconstructed and rebuilt. As part of this process we also argue that much can be gained from applying ideas, concepts, and principles from agile software development methods. To be sure we are not arguing for a rote application of these agile software approaches, however, given various trends related to data and technology, it is imperative to update our thinking about how to approach the data management lifecycle, recognize differing project scales, corresponding variations in structure, and alternative models for solving the problems of scientific data curation. In this paper we will describe what we term agile curation design patterns, borrowing the concept of design patterns from the software world and we will present some initial thoughts on agile curation design patterns as informed by a sample of data curation case studies solicited from participants in agile data curation meeting sessions conducted in 2015-16.

The synergistic effect of non-stoichiometry and Sb-doping on air-stable α-CsPbI3 for efficient carbon-based perovskite solar cells.

PubMed

Xiang, Sisi; Li, Weiping; Wei, Ya; Liu, Jiaming; Liu, Huicong; Zhu, Liqun; Chen, Haining

2018-05-18

α-CsPbI3 with the most suitable band gap for all-inorganic perovskite solar cell (PSC) application faces an issue of phase instability at low temperature in an air atmosphere. Herein, through stoichiometric investigation, α-CsPbI3 is successfully obtained with excess CsI at 110 °C in an air atmosphere. By doping α-CsPbI3 with Sb, phase stability is further enhanced and the film morphology is also improved. Carbon-based perovskite solar cells (C-PSCs) based on CsPb0.96Sb0.04I3 achieve a promising power conversion efficiency (PCE) of 5.18%, a record value for α-CsPbI3-based PSCs without hole transport materials. Significantly, the CsPb0.96Sb0.04I3 C-PSCs retain 93% of the initial PCE after 37 days of storage in an air atmosphere. Therefore, the synergistic effect of non-stoichiometry and Sb-doping presents a promising strategy to design all-inorganic lead halide PSCs with high performance and stability.

Surface cleaning and pure nitridation of GaSb by in-situ plasma processing

NASA Astrophysics Data System (ADS)

Gotow, Takahiro; Fujikawa, Sachie; Fujishiro, Hiroki I.; Ogura, Mutsuo; Chang, Wen Hsin; Yasuda, Tetsuji; Maeda, Tatsuro

2017-10-01

A clean and flat GaSb surface without native oxides has been attained by H2 plasma cleaning and subsequent in-situ N2 plasma nitridation process at 300 oC. The mechanisms of thermal desorption behavior of native oxides on GaSb have been studied by thermal desorption spectroscopy (TDS) analysis. The suitable heat treatment process window for preparing a clean GaSb surface is given. Auger electron spectroscopy (AES) analysis indicates that native oxides were completely removed on the GaSb surface after H2 plasma exposure and the pure nitridation of the clean GaSb surface was obtained at a relatively low temperature of 300 °C. This pure nitridation of GaSb have a possibility to be used as a passivation layer for high quality GaSb MOS devices.

Agile Objects

ERIC Educational Resources Information Center

German, Senta; Harris, Jim

2017-01-01

In this article, the authors argue that the art-historical canon, however it is construed, has little relevance to the selection of objects for museum-based teaching. Their contention is that all objects are fundamentally agile and capable of interrogation from any number of disciplinary standpoints, and that the canon of museum education,…

The structure directing effect of organic cations onto the crystal structures of layered thioantimonates(III): Solvothermal synthesis and crystal structures of five new compounds containing the 2∞[Sb 8S 13] 2- anion

NASA Astrophysics Data System (ADS)

Puls, Angela; Näther, Christian; Kiebach, Ragnar; Bensch, Wolfgang

2006-09-01

The five new thioantimonates(III) ( iprH) 2[Sb 8S 13] ( I), (1,2-dapH) 2[Sb 8S 13] ( II), (1,3-dapH 2)[Sb 8S 13] ( III), (dienH 2)[Sb 8S 13]ṡ1.5H 2O ( IV), and (C 6H 9N 2)[Sb 8S 13]ṡ2.5H 2O ( V) were synthesised under solvothermal conditions ( ipr = iso-propylamine; 1,2-dap = 1,2-diaminopropane; 1,3-dap = 1,3-diaminopropane; dien = diethylentriamine; C 6H 9N 2 = 3-(aminoethyl)-pyridine). The structures of compounds I and II are topological very similar and a central motif is a Sb 10S 10 ring. On both sides of this ring Sb 5S 5 rings are condensed. These rings are connected via Sb 4S 4 rings leading to the sequence Sb 10S 10-Sb 5S 5-Sb 4S 4-Sb 5S 5-Sb 10Sb 10 in the [010] direction. Further interconnection into the two-dimensional [Sb 8S 13] 2- anion produces a large central Sb 18S 18 ring with dimensions of 11ṡ11 Å in both compounds. The two atoms thick layers are linear and stacked along the a axis generating large channels running along [010]. The layered anion of compound III is constructed by interconnection of the SbS 3 and SbS 4 units yielding Sb 19S 19, Sb 14S 14, Sb 13S 13, and Sb 8S 8 rings. The linear layers are two atoms thick and are stacked perpendicular to [001] to form channels running along the same direction. The last two compounds IV and V show a similar network topology. The layered anion is constructed by SbS 3 trigonal pyramids and SbS 4 units. The layer contains a Sb 12S 12 rings as the main structural motif. The corrugated layers extending in the (100) plane are two atoms thick and are stacked in a manner that large tunnels run along [100]. The total potential solvent areas are large and range from 20.7% for III to 35% for II.

The agile alert system for gamma-ray transients

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bulgarelli, A.; Trifoglio, M.; Gianotti, F.

2014-01-20

In recent years, a new generation of space missions has offered great opportunities for discovery in high-energy astrophysics. In this article we focus on the scientific operations of the Gamma-Ray Imaging Detector (GRID) on board the AGILE space mission. AGILE-GRID, sensitive in the energy range of 30 MeV-30 GeV, has detected many γ-ray transients of both galactic and extragalactic origin. This work presents the AGILE innovative approach to fast γ-ray transient detection, which is a challenging task and a crucial part of the AGILE scientific program. The goals are to describe (1) the AGILE Gamma-Ray Alert System, (2) a newmore » algorithm for blind search identification of transients within a short processing time, (3) the AGILE procedure for γ-ray transient alert management, and (4) the likelihood of ratio tests that are necessary to evaluate the post-trial statistical significance of the results. Special algorithms and an optimized sequence of tasks are necessary to reach our goal. Data are automatically analyzed at every orbital downlink by an alert pipeline operating on different timescales. As proper flux thresholds are exceeded, alerts are automatically generated and sent as SMS messages to cellular telephones, via e-mail, and via push notifications from an application for smartphones and tablets. These alerts are crosschecked with the results of two pipelines, and a manual analysis is performed. Being a small scientific-class mission, AGILE is characterized by optimization of both scientific analysis and ground-segment resources. The system is capable of generating alerts within two to three hours of a data downlink, an unprecedented reaction time in γ-ray astrophysics.« less

The AGILE Alert System for Gamma-Ray Transients

NASA Astrophysics Data System (ADS)

Bulgarelli, A.; Trifoglio, M.; Gianotti, F.; Tavani, M.; Parmiggiani, N.; Fioretti, V.; Chen, A. W.; Vercellone, S.; Pittori, C.; Verrecchia, F.; Lucarelli, F.; Santolamazza, P.; Fanari, G.; Giommi, P.; Beneventano, D.; Argan, A.; Trois, A.; Scalise, E.; Longo, F.; Pellizzoni, A.; Pucella, G.; Colafrancesco, S.; Conforti, V.; Tempesta, P.; Cerone, M.; Sabatini, P.; Annoni, G.; Valentini, G.; Salotti, L.

2014-01-01

In recent years, a new generation of space missions has offered great opportunities for discovery in high-energy astrophysics. In this article we focus on the scientific operations of the Gamma-Ray Imaging Detector (GRID) on board the AGILE space mission. AGILE-GRID, sensitive in the energy range of 30 MeV-30 GeV, has detected many γ-ray transients of both galactic and extragalactic origin. This work presents the AGILE innovative approach to fast γ-ray transient detection, which is a challenging task and a crucial part of the AGILE scientific program. The goals are to describe (1) the AGILE Gamma-Ray Alert System, (2) a new algorithm for blind search identification of transients within a short processing time, (3) the AGILE procedure for γ-ray transient alert management, and (4) the likelihood of ratio tests that are necessary to evaluate the post-trial statistical significance of the results. Special algorithms and an optimized sequence of tasks are necessary to reach our goal. Data are automatically analyzed at every orbital downlink by an alert pipeline operating on different timescales. As proper flux thresholds are exceeded, alerts are automatically generated and sent as SMS messages to cellular telephones, via e-mail, and via push notifications from an application for smartphones and tablets. These alerts are crosschecked with the results of two pipelines, and a manual analysis is performed. Being a small scientific-class mission, AGILE is characterized by optimization of both scientific analysis and ground-segment resources. The system is capable of generating alerts within two to three hours of a data downlink, an unprecedented reaction time in γ-ray astrophysics.

Agile, a guiding principle for health care improvement?

PubMed

Tolf, Sara; Nyström, Monica E; Tishelman, Carol; Brommels, Mats; Hansson, Johan

2015-01-01

The purpose of this paper is to contribute to increased understanding of the concept agile and its potential for hospital managers to optimize design of organizational structures and processes to combine internal efficiency and external effectiveness. An integrative review was conducted using the reSEARCH database. Articles met the following criteria: first, a definition of agility; second, descriptions of enablers of becoming an agile organization; and finally, discussions of agile on multiple organizational levels. In total, 60 articles qualified for the final analysis. Organizational agility rests on the assumption that the environment is uncertain, ranging from frequently changing to highly unpredictable. Proactive, reactive or embracive coping strategies were described as possible ways to handle such uncertain environments. Five organizational capacities were derived as necessary for hospitals to use the strategies optimally: transparent and transient inter-organizational links; market sensitivity and customer focus; management by support for self-organizing employees; organic structures that are elastic and responsive; flexible human and resource capacity for timely delivery. Agile is portrayed as either the "new paradigm" following lean, the needed development on top of a lean base, or as complementary to lean in distinct hybrid strategies. Environmental uncertainty needs to be matched with coping strategies and organizational capacities to design processes responsive to real needs of health care. This implies that lean and agile can be combined to optimize the design of hospitals, to meet different variations in demand and create good patient management. While considerable value has been paid to strategies to improve the internal efficiency within hospitals, this review raise the attention to the value of strategies of external effectiveness.

Agility in Team Sports: Testing, Training and Factors Affecting Performance.

PubMed

Paul, Darren J; Gabbett, Tim J; Nassis, George P

2016-03-01

Agility is an important characteristic of team sports athletes. There is a growing interest in the factors that influence agility performance as well as appropriate testing protocols and training strategies to assess and improve this quality. The objective of this systematic review was to (1) evaluate the reliability and validity of agility tests in team sports, (2) detail factors that may influence agility performance, and (3) identify the effects of different interventions on agility performance. The review was undertaken in accordance with the Preferred Reporting Items for Systematic Reviews and Meta-Analyses guidelines. We conducted a search of PubMed, Google Scholar, Science Direct, and SPORTDiscus databases. We assessed the methodological quality of intervention studies using a customized checklist of assessment criteria. Intraclass correlation coefficient values were 0.80-0.91, 0.10-0.81, and 0.81-0.99 for test time using light, video, and human stimuli. A low-level reliability was reported for youth athletes using the video stimulus (0.10-0.30). Higher-level participants were shown to be, on average, 7.5% faster than their lower level counterparts. Reaction time and accuracy, foot placement, and in-line lunge movement have been shown to be related to agility performance. The contribution of strength remains unclear. Efficacy of interventions on agility performance ranged from 1% (vibration training) to 7.5% (small-sided games training). Agility tests generally offer good reliability, although this may be compromised in younger participants responding to various scenarios. A human and/or video stimulus seems the most appropriate method to discriminate between standard of playing ability. Decision-making and perceptual factors are often propositioned as discriminant factors; however, the underlying mechanisms are relatively unknown. Research has focused predominantly on the physical element of agility. Small-sided games and video training may offer effective

Superconductivity in BaPtSb with an Ordered Honeycomb Network

NASA Astrophysics Data System (ADS)

Kudo, Kazutaka; Saito, Yuki; Takeuchi, Takaaki; Ayukawa, Shin-ya; Kawamata, Takayuki; Nakamura, Shinichiro; Koike, Yoji; Nohara, Minoru

2018-06-01

Superconductivity in BaPtSb with the SrPtSb-type structure (space group P\\bar{6}m2, D3h1, No. 187) is reported. The structure consists of a PtSb ordered honeycomb network that stacks along the c-axis so that spatial inversion symmetry is broken globally. Electrical resistivity and specific-heat measurements revealed that the compound exhibited superconductivity at 1.64 K. The noncentrosymmetric structure and the strong spin-orbit coupling of Pt and Sb make BaPtSb an attractive compound for studying the exotic superconductivity predicted for a honeycomb network.

Effect of the C3a-receptor antagonist SB 290157 on anti-OVA polyclonal antibody-induced arthritis.

PubMed

Hutamekalin, Pilaiwanwadee; Takeda, Kohei; Tani, Mitsuhiro; Tsuga, Yuko; Ogawa, Naoki; Mizutani, Nobuaki; Yoshino, Shin

2010-01-01

It was investigated whether the C3a-receptor antagonist (C3aRA) SB 290157 was involved in the suppression of anti-OVA pAb-induced arthritis because it is well known that anaphylatoxin C3a plays a crucial role in the development of an effective inflammatory response during complement activation. Anti-OVA pAb-induced arthritis was induced in DBA/1J mice by administration of anti-OVA pAb 0.5 h prior to intra-articular (i.a.) injection of OVA (0 h). Two peaks of joint swelling were observed at 0.5 and 3 h. The role of C3aRA in arthritis was investigated by injection of SB 290157 at concentrations of 10 and 30 mg/kg at 0 and 2 h. The antagonist was able to reduce joint swelling only at 3 h, and about 50% inhibition of joint swelling was observed with the concentration of 30 mg/kg. The C3 level was significantly decreased at 3 h compared with naïve mice showing complement consumption. Furthermore, the C3 activation was observed and increased corresponding to the graded concentration of anti-OVA pAb. The results also revealed that the C3aRA was able to reduce the expression of IL-1beta in synovial tissue. Taken together, the results suggested that C3aRA may be effective in the inhibition of arthritis.

Chemical route for formation of intermetallic Zn 4Sb 3 phase

NASA Astrophysics Data System (ADS)

Denoix, A.; Solaiappan, A.; Ayral, R. M.; Rouessac, F.; Tedenac, J. C.

2010-05-01

Synthesis of intermetallic zinc antimonide phases via low temperature solution route was investigated. Trial experiments were carried out under inert atmosphere at 70 °C using metallic Zn, SbCl 3 and NaBH 4 as reactants and tetrahydrofuran (THF), dimethylsulfoxide (DMSO) as organic media. Powder X-ray analysis confirmed the nucleation and growth of ZnSb phases in presence of excess Zn. SEM analysis revealed the existence of core-shell structure comprising of Zn core and Sb shell. Such particles get transformed into Zn 4Sb 3 crystalline phases upon thermal treatment at 300 °C/6 h in a silica tube closed under high secondary vacuum.

Multilayer SnSb4-SbSe Thin Films for Phase Change Materials Possessing Ultrafast Phase Change Speed and Enhanced Stability.

PubMed

Liu, Ruirui; Zhou, Xiao; Zhai, Jiwei; Song, Jun; Wu, Pengzhi; Lai, Tianshu; Song, Sannian; Song, Zhitang

2017-08-16

A multilayer thin film, comprising two different phase change material (PCM) components alternatively deposited, provides an effective means to tune and leverage good properties of its components, promising a new route toward high-performance PCMs. The present study systematically investigated the SnSb 4 -SbSe multilayer thin film as a potential PCM, combining experiments and first-principles calculations, and demonstrated that these multilayer thin films exhibit good electrical resistivity, robust thermal stability, and superior phase change speed. In particular, the potential operating temperature for 10 years is shown to be 122.0 °C and the phase change speed reaches 5 ns in the device test. The good thermal stability of the multilayer thin film is shown to come from the formation of the Sb 2 Se 3 phase, whereas the fast phase change speed can be attributed to the formation of vacancies and a SbSe metastable phase. It is also demonstrated that the SbSe metastable phase contributes to further enhancing the electrical resistivity of the crystalline state and the thermal stability of the amorphous state, being vital to determining the properties of the multilayer SnSb 4 -SbSe thin film.

Effect of Sb on physical properties and microstructures of laser nano/amorphous-composite film

NASA Astrophysics Data System (ADS)

Li, Jia-Ning; Gong, Shui-Li; Sun, Mei; Shan, Fei-Hu; Wang, Xi-Chang; Jiang, Shuai

2013-11-01

A nano/amorphous-composite film was fabricated by laser cladding (LC) of the Co-Ti-B4C-Sb mixed powders on a TA15 alloy. Such film mainly consisted of Ti-Al, Co-Ti, Co-Sb intermetallics, TiC, TiB2, TiB, and the amorphous phases. Experimental results indicated that the crystal systems of TiB2 (hexagonal)/TiC (cubic) and Sb (rhombohedral) played important role on the formation of such film. Due to the mismatch of these crystals systems and mutual immiscibility of the metallic components, Sb was not incorporated in TiB2/TiC, but formed separate nuclei during the film growth. Thus, the growth of TiB2/TiC was stopped by the Sb nucleus in such LC molten pool, so as to form the nanoscale particles.

Teaching Agile Software Development: A Case Study

ERIC Educational Resources Information Center

Devedzic, V.; Milenkovic, S. R.

2011-01-01

This paper describes the authors' experience of teaching agile software development to students of computer science, software engineering, and other related disciplines, and comments on the implications of this and the lessons learned. It is based on the authors' eight years of experience in teaching agile software methodologies to various groups…

In-situ crystallization of GeTe\\GaSb phase change memory stacked films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Velea, A., E-mail: alin.velea@psi.ch; National Institute of Materials Physics, RO-077125 Magurele, Ilfov; Borca, C. N.

2014-12-21

Single and double layer phase change memory structures based on GeTe and GaSb thin films were deposited by pulsed laser deposition (PLD). Their crystallization behavior was studied using in-situ synchrotron techniques. Electrical resistance vs. temperature investigations, using the four points probe method, showed transition temperatures of 138 °C and 198 °C for GeTe and GaSb single films, respectively. It was found that after GeTe crystallization in the stacked films, Ga atoms from the GaSb layer diffused in the vacancies of the GeTe crystalline structure. Therefore, the crystallization temperature of the Sb-rich GaSb layer is decreased by more than 30 °C. Furthermore, at 210 °C,more » the antimony excess from GaSb films crystallizes as a secondary phase. At higher annealing temperatures, the crystalline Sb phase increased on the expense of GaSb crystalline phase which was reduced. Extended X-ray absorption fine structure (EXAFS) measurements at the Ga and Ge K-edges revealed changes in their local atomic environments as a function of the annealing temperature. Simulations unveil a tetrahedral configuration in the amorphous state and octahedral configuration in the crystalline state for Ge atoms, while Ga is four-fold coordinated in both as-deposited and annealed samples.« less

The Co-Sb-Ga System: Isoplethal Section and Thermodynamic Modeling

NASA Astrophysics Data System (ADS)

Gierlotka, Wojciech; Chen, Sinn-wen; Chen, Wei-an; Chang, Jui-shen; Snyder, G. Jeffrey; Tang, Yinglu

2015-04-01

The Co-Sb-Ga ternary system is an important thermoelectric material system, and its phase equilibria are in need of further understanding. The CoSb3-GaSb isoplethal section is experimentally determined in this study. Phase equilibria of the ternary Co-Sb-Ga system are assessed, and the system's thermodynamic models are developed. In addition to the terminal phases and liquid phase, there are six binary intermediate phases and a ternary Co3Sb2Ga4 phase. The Ga solution in the CoSb3 compound is described by a dual-site occupation (GaVF) x Co4Sb12- x/2(GaSb) x/2 model. Phase diagrams are calculated using the developed thermodynamic models, and a reaction scheme is proposed based on the calculation results. The calculated results are in good agreement with the experimentally determined phase diagrams, including the CoSb3-GaSb isoplethal section, the liquidus projection, and an isothermal section at 923 K (650 °C). The dual-site occupation (GaVF) x Co4Sb12- x/2(GaSb) x/2 model gives good descriptions of both phase equilibria and thermoelectric properties of the CoSb3 phase with Ga doping.

Agile Methods in Air Force Sustainment: Status and Outlook

DTIC Science & Technology

2014-07-01

Schwaber ISBN10: 073561993X X X Agile Project Management : Creating Innovative Products – 2nd Edition Jim Highsmith ISBN 0321658396 X Agile...ISBN 0787974277 X Leading Change John Kotter ISBN 0875847471 X Leading Geeks: How to Manage and Lead the People Who Deliver Technology Paul ...Development: Achieving Enterprise Agility Alan Shalloway, Guy Beaver, and James R. Trott ISBN 0321532899 X Managing Transitions: Making the Most of

[Simultaneous determination of canthaxanthin and astaxanthin in feedstuffs using solid phase extraction-reversed-phase high performance liquid chromatography].

PubMed

Zhang, Hua; Yang, Xin; Ma, Ying; Dong, Aijun; Zhang, Yingchun

2008-05-01

A method was developed for the simultaneous determination of canthaxanthin and astaxanthin in feedstuffs using reversed-phase high performance liquid chromatography (RP-HPLC). The sample was extracted by acetonitrile, and cleaned up by an LC-NH2 column. An Agilent ZORBAX Eclipse XDB-C18 analytical column (150 mm x 4.6 mm, 5 microm) was used and kept at 25 degrees C. Acetonitrile-methanol (95 : 5, v/v) was used as the mobile phase at a flow rate of 1.0 mL/min. The detection was performed by a diode array detector at 474 nm. The quantitive analysis of external standard calibration curves was used. The linear ranges of the method for canthaxanthin and astaxanthin were 1.0 - 30.0 mg/L (r = 0.999 0) and 1.0 - 20.0 mg/L (r = 0.999 1), respectively. The average recoveries were 90% - 101% with the relative standard deviations of 0.62% - 3.68%. The detection limits were 0.84 and 0.60 mg/L for canthaxanthin and astaxanthin, respectively. The method is simple, precise, sensitive and reproductive. It can be used to determine the contents of canthaxanthin and astaxanthin in feedstuffs.

Linear and nonlinear optical properties of Sb-doped GeSe2 thin films

NASA Astrophysics Data System (ADS)

Zhang, Zhen-Ying; Chen, Fen; Lu, Shun-Bin; Wang, Yong-Hui; Shen, Xiang; Dai, Shi-Xun; Nie, Qiu-Hua

2015-06-01

Sb-doped GeSe2 chalcogenide thin films are prepared by the magnetron co-sputtering method. The linear optical properties of as-deposited films are derived by analyzing transmission spectra. The refractive index rises and the optical band gap decreases from 2.08 eV to 1.41 eV with increasing the Sb content. X-ray photoelectron spectra further confirm the formation of a covalent Sb-Se bond. The third-order nonlinear optical properties of thin films are investigated under femtosecond laser excitation at 800 nm. The results show that the third-order nonlinear optical properties are enhanced with increasing the concentration of Sb. The nonlinear refraction indices of these thin films are measured to be on the order of 10-18 m2/W with a positive sign and the nonlinear absorption coefficients are obtained to be on the order of 10-10 m/W. These excellent properties indicate that Sb-doped Ge-Se films have a good prospect in the applications of nonlinear optical devices. Project supported by the National Key Basic Research Program of China (Grant No. 2012CB722703), the National Natural Science Foundation of China (Grant No. 61377061), the Young Leaders of Academic Climbing Project of the Education Department of Zhejiang Province, China (Grant No. pd2013092), the Program for Innovative Research Team of Ningbo City, China (Grant No. 2009B217), and the K. C. Wong Magna Fund in Ningbo University, China.

[Determination of optical purity of alpha-phenylethylamine by high performance liquid chromatography with pre-column derivatization].

PubMed

Wang, Jinzhao; Zeng, Su; Wang, Danhua; Hu, Gongyun

2009-05-01

A simple pre-column derivatization-high performance liquid chromatographic (HPLC) method was established for the determination of optical purity of alpha-phenylethylamine. The enantiomers of alpha-phenylethylamine were derivatized with 2,3,4,6-tetra-O-acetyl-beta-D-glucopyranosyl isothiocyanate (GITC). The resulted diastereoisomers were separated on an Agilent Zorbax C18 column (250 mm x 4.6 mm, 5 microm) with a mobile phase of methanol-phosphate buffer (1.36 g/L aqueous solution of potassium dihydrogen phosphate, adjusted to pH 3.0 with concentrated phosphoric acid) (58:42, v/v). The flow rate was set at 1.0 mL/min and the detection wavelength was set at 241 nm. The method was linear from 0.15 - 15.0 mg/L for both enantiomers. The limit of detection and the limit of quantification were 0.05 mg/L and 0.15 mg/L, respectively. The relative standard deviations (RSDs) of inter- and intra-day determination were below 0.5%. The method is easy to handle, accurate, and suitable for the quality control of the optical purity of alpha-phenylethylamine.

Thermal stability of active/inactive nanocomposite anodes based on Cu2Sb in lithium-ion batteries

NASA Astrophysics Data System (ADS)

Allcorn, Eric; Kim, Sang-Ok; Manthiram, Arumugam

2015-12-01

Various active/inactive nanocomposites of Cu2Sb-Al2O3@C, Cu2Sb-TiC, and Cu2Sb-TiC@C have been synthesized by high energy mechanical milling and investigated by differential scanning calorimetry (DSC) to determine the lithiated phase stability and heat generation arising from these electrodes. The milling process reduces the Li3Sb phase stability, relative to the un-milled samples, to below ∼200 °C. However, the incorporation of the reinforcing, inactive phases Al2O3, TiC, and carbon black offer a slight improvement. DSC curves also show that the low-temperature heat generation in the SEI-layer reaction range is not noticeably altered by either the milling process or the addition of the inactive phases. A strong exothermic peak is observed at ∼200 °C for the 0% state of charge electrodes of Cu2Sb-Al2O3@C and Cu2Sb-TiC@C that was caused by the incorporation of carbon black into the composite. This peak was not present in the electrodes of milled Cu2Sb or Cu2Sb-TiC, suggesting that efforts to extend the cycle life of alloy anodes should avoid carbon black due to its destabilizing effects on delithiated electrodes. Fourier Transform infrared spectroscopy analysis indicates that the reaction arising from the incorporation of carbon black is tied to a low-temperature breakdown of the lithium salt LiPF6.

A Case Study of Coordination in Distributed Agile Software Development

NASA Astrophysics Data System (ADS)

Hole, Steinar; Moe, Nils Brede

Global Software Development (GSD) has gained significant popularity as an emerging paradigm. Companies also show interest in applying agile approaches in distributed development to combine the advantages of both approaches. However, in their most radical forms, agile and GSD can be placed in each end of a plan-based/agile spectrum because of how work is coordinated. We describe how three GSD projects applying agile methods coordinate their work. We found that trust is needed to reduce the need of standardization and direct supervision when coordinating work in a GSD project, and that electronic chatting supports mutual adjustment. Further, co-location and modularization mitigates communication problems, enables agility in at least part of a GSD project, and renders the implementation of Scrum of Scrums possible.

Planned and reactive agility performance in semiprofessional and amateur basketball players.

PubMed

Lockie, Robert G; Jeffriess, Matthew D; McGann, Tye S; Callaghan, Samuel J; Schultz, Adrian B

2014-09-01

Research indicates that planned and reactive agility are different athletic skills. These skills have not been adequately assessed in male basketball players. To define whether 10-m-sprint performance and planned and reactive agility measured by the Y-shaped agility test can discriminate between semiprofessional and amateur basketball players. Ten semiprofessional and 10 amateur basketball players completed 10-m sprints and planned- and reactive-agility tests. The Y-shaped agility test involved subjects sprinting 5 m through a trigger timing gate, followed by a 45° cut and 5-m sprint to the left or right through a target gate. In the planned condition, subjects knew the cut direction. For reactive trials, subjects visually scanned to find the illuminated gate. A 1-way analysis of variance (P < .05) determined between-groups differences. Data were pooled (N = 20) for a correlation analysis (P < .05). The reactive tests differentiated between the groups; semiprofessional players were 6% faster for the reactive left (P = .036) and right (P = .029) cuts. The strongest correlations were between the 10-m sprints and planned-agility tests (r = .590-.860). The reactive left cut did not correlate with the planned tests. The reactive right cut moderately correlated with the 10-m sprint and planned right cut (r = .487-.485). The results reemphasized that planned and reactive agility are separate physical qualities. Reactive agility discriminated between the semiprofessional and amateur basketball players; planned agility did not. To distinguish between male basketball players of different ability levels, agility tests should include a perceptual and decision-making component.

Pilot users in agile development processes: motivational factors.

PubMed

Johannessen, Liv Karen; Gammon, Deede

2010-01-01

Despite a wealth of research on user participation, few studies offer insights into how to involve multi-organizational users in agile development methods. This paper is a case study of user involvement in developing a system for electronic laboratory requisitions using agile methodologies in a multi-organizational context. Building on an interpretive approach, we illuminate questions such as: How does collaboration between users and developers evolve and how might it be improved? What key motivational aspects are at play when users volunteer and continue contributing in the face of considerable added burdens? The study highlights how agile methods in themselves appear to facilitate mutually motivating collaboration between user groups and developers. Lessons learned for leveraging the advantages of agile development processes include acknowledging the substantial and ongoing contributions of users and their roles as co-designers of the system.

Combining Agile and Traditional: Customer Communication in Distributed Environment

NASA Astrophysics Data System (ADS)

Korkala, Mikko; Pikkarainen, Minna; Conboy, Kieran

Distributed development is a radically increasing phenomenon in modern software development environments. At the same time, traditional and agile methodologies and combinations of those are being used in the industry. Agile approaches place a large emphasis on customer communication. However, existing knowledge on customer communication in distributed agile development seems to be lacking. In order to shed light on this topic and provide practical guidelines for companies in distributed agile environments, a qualitative case study was conducted in a large globally distributed software company. The key finding was that it might be difficult for an agile organization to get relevant information from a traditional type of customer organization, even though the customer communication was indicated to be active and utilized via multiple different communication media. Several challenges discussed in this paper referred to "information blackout" indicating the importance of an environment fostering meaningful communication. In order to evaluate if this environment can be created a set of guidelines is proposed.

The AGILE Mission and Gamma-Ray Bursts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Longo, Francesco; INFN, section of Trieste; Tavani, M.

2007-05-01

The AGILE Mission will explore the gamma-ray Universe with a very innovative instrument combining for the first time a gamma-ray imager and a hard X-ray imager. AGILE will be operational at the beginning of 2007 and it will provide crucial data for the study of Active Galactic Nuclei, Gamma-Ray Bursts, unidentified gamma-ray sources, Galactic compact objects, supernova remnants, TeV sources, and fundamental physics by microsecond timing. The AGILE instrument is designed to simultaneously detect and image photons in the 30 MeV - 50 GeV and 15 - 45 keV energy bands with excellent imaging and timing capabilities, and a largemore » field of view covering {approx} 1/5 of the entire sky at energies above 30 MeV. A CsI calorimeter is capable of GRB triggering in the energy band 0.3-50 MeV. The broadband detection of GRBs and the study of implications for particle acceleration and high energy emission are primary goals of the mission. AGILE can image GRBs with 2-3 arcminute error boxes in the hard X-ray range, and provide broadband photon-by photon detection in the 15-45 keV, 03-50 MeV, and 30 MeV-30 GeV energy ranges. Microsecond on-board photon tagging and a {approx} 100 microsecond gamma-ray detection deadtime will be crucial for fast GRB timing. On-board calculated GRB coordinates and energy fluxes will be quickly transmitted to the ground by an ORBCOMM transceiver. AGILE is now (January 2007) undergoing final satellite integration and testing. The PLS V launch is planned in spring 2007. AGILE is then foreseen to be fully operational during the summer of 2007.« less

Gender-specific influences of balance, speed, and power on agility performance.

PubMed

Sekulic, Damir; Spasic, Miodrag; Mirkov, Dragan; Cavar, Mile; Sattler, Tine

2013-03-01

The quick change of direction (i.e., agility) is an important athletic ability in numerous sports. Because of the diverse and therefore hardly predictable manifestations of agility in sports, studies noted that the improvement in speed, power, and balance should result in an improvement of agility. However, there is evident lack of data regarding the influence of potential predictors on different agility manifestations. The aim of this study was to determine the gender-specific influence of speed, power, and balance on different agility tests. A total of 32 college-aged male athletes and 31 college-aged female athletes (age 20.02 ± 1.89 years) participated in this study. The subjects were mostly involved in team sports (soccer, team handball, basketball, and volleyball; 80% of men, and 75% of women), martial arts, gymnastics, and dance. Anthropometric variables consisted of body height, body weight, and the body mass index. Five agility tests were used: a t-test (T-TEST), zig-zag test, 20-yard shuttle test, agility test with a 180-degree turn, and forward-backward running agility test (FWDBWD). Other tests included 1 jumping ability power test (squat jump, SQJ), 2 balance tests to determine the overall stability index and an overall limit of stability score (both measured by Biodex Balance System), and 2 running speed tests using a straight sprint for 10 and 20 m (S10 and S20, respectively). A reliability analysis showed that all the agility tests were reliable. Multiple regression and correlation analysis found speed and power (among women), and balance (among men), as most significant predictors of agility. The highest Pearson's correlation in both genders is found between the results of the FWDBWD and S10M tests (0.77 and 0.81 for men and women, respectively; p < 0.05). Power, measured using the SQJ, is significantly (p < 0.05) related to FWDBWD and T-TEST results but only for women (-0.44; -0.41). The balance measures were significantly related to the agility

Applying Agile Principles in Teaching Undergraduate Information Technology Project Management

ERIC Educational Resources Information Center

Budu, Joseph

2018-01-01

This article describes how the traditional teaching and learning activities over the years have been challenged to be agile--easily adaptable to changing classroom conditions. Despite this new phenomenon, there is a perceived paucity of agile-in-teaching research. Available studies neither focus on the use of agile principles beyond delivering…

A comparison of linear speed, closed-skill agility, and open-skill agility qualities between backcourt and frontcourt adult semiprofessional male basketball players.

PubMed

Scanlan, Aaron T; Tucker, Patrick S; Dalbo, Vincent J

2014-05-01

The measurement of fitness qualities relevant to playing position is necessary to inform basketball coaching and conditioning staff of role-related differences in playing groups. To date, sprinting and agility performance have not been compared between playing positions in adult male basketball players. Therefore, the purpose of this study was to describe and compare linear speed, closed-skill agility, and open-skill agility qualities between backcourt (point guard and shooting guard positions) and frontcourt (small forward, power forward, and center positions) semiprofessional basketball players. Six backcourt (mean ± SD: age, 24.3 ± 7.9 years; stature, 183.4 ± 4.0 cm; body mass, 85.5 ± 12.3 kg; VO2max, 51.9 ± 4.8 ml·kg(-1)·min(-1)) and 6 frontcourt (mean ± SD: age, 27.5 ± 5.5 years; stature, 194.4 ± 7.1 cm; body mass, 109.4 ± 8.8 kg; VO2max, 47.1 ± 5.0 ml·kg(-1)·min(-1)) adult male basketball players completed 20-m sprint, closed-skill agility, and open-skill agility performance tests. Magnitude-based inferences revealed that backcourt players (5 m, 1.048 ± 0.027 seconds; 10 m, 1.778 ± 0.048 seconds; 20 m, 3.075 ± 0.121 seconds) possessed likely quicker linear sprint times than frontcourt players (5 m, 1.095 ± 0.085 seconds; 10 m, 1.872 ± 0.127 seconds; 20 m, 3.242 ± 0.221 seconds). Conversely, frontcourt players (1.665 ± 0.096 seconds) held possible superior closed-skill agility performance than backcourt players (1.613 ± 0.111 seconds). In addition, unclear positional differences were apparent for open-skill agility qualities. These findings indicate that linear speed and change of direction speed might be differently developed across playing positions. Furthermore, position-related functions might similarly depend on the aspects of open-skill agility performance across backcourt and frontcourt players. Basketball coaching and conditioning staff should consider the development of position-targeted training drills to improve speed, agility

New approaches with two cyano columns to the separation of acetaminophen, phenylephrine, chlorpheniramine and related compounds.

PubMed

Olmo, B; García, A; Marín, A; Barbas, C

2005-03-25

The development of new pharmaceutical forms with classical active compounds generates new analytical problems. That is the case of sugar-free sachets of cough-cold products containing acetaminophen, phenylephrine hydrochloride and chlorpheniramine maleate. Two cyanopropyl stationary phases have been employed to tackle the problem. The Discovery cyanopropyl (SUPELCO) column permitted the separation of the three actives, maleate and excipients (mainly saccharine and orange flavour) with a constant proportion of aqueous/ organic solvent (95:5, v/v) and a pH gradient from 7.5 to 2. The run lasted 14 min. This technique avoids many problems related to baseline shifts with classical organic solvent gradients and opens great possibilities to modify selectivity not generally used in reversed phase HPLC. On the other hand, the Agilent Zorbax SB-CN column with a different retention profile permitted us to separate not only the three actives and the excipients but also the three known related compounds: 4-aminophenol, 4-chloracetanilide and 4-nitrophenol in an isocratic method with a run time under 30 min. This method was validated following ICH guidelines and validation parameters showed that it could be employed as stability-indicating method for this pharmaceutical form.

Growth and characterization of chalcostibite CuSbSe2 thin films for photovoltaic application

NASA Astrophysics Data System (ADS)

Tiwari, Kunal J.; Vinod, Vijay; Subrahmanyam, A.; Malar, P.

2017-10-01

Bulk copper antimony selenide was synthesized using mechanical alloying from the elemental precursors. Phase formation in milled powders was studied using x-ray diffraction (XRD) and Raman spectroscopy studies. The synthesized bulk source after cold compaction was used as source material for thin film deposition by e-beam evaporation. Thin film deposition was carried out at various e-beam current values (Ib ∼30, 40 and 50 mA) and at a substrate temperature of 200 °C. Near stoichiometric CuSbSe2 thin films were obtained for Ib values closer to 50 mA and post annealing at a temperature of 380 °C for 1 h. Thin films deposited using above conditions were found to exhibit an absorption coefficient (α) values of >105 cm-1 and a band gap value ∼1.18 eV that is closer to the reported band gap for CuSbSe2 compound.

Electrical and optical characterization of n-InAsSb/n-GaSb heterojunctions

NASA Astrophysics Data System (ADS)

Lackner, D.; Martine, M.; Cherng, Y. T.; Steger, M.; Walukiewicz, W.; Thewalt, M. L. W.; Mooney, P. M.; Watkins, S. P.

2010-01-01

We report the electrical properties of n-InAsSb/n-GaSb heterojunctions as a function of the GaSb doping concentration. Because of the staggered type II band alignment, strong electron accumulation occurs on the InAsSb side. For low GaSb doping, depletion occurs on the GaSb side resulting in a Schottky-like junction as previously reported. As the GaSb doping increases, the built-in voltage as well as depletion width decreases as shown using self-consistent simulations. For GaSb doping levels above 5×1017 cm-3, the junction loses its rectifying properties due to tunneling. Under zero and reverse bias voltage, the photoresponse of these diodes is solely due to the photovoltaic effect in the GaSb depletion region. For forward bias voltages >400 mV, we also observed a photoconductive response from the InAsSb layer. The proposed physical mechanism is quite different from the one suggested in a recent paper.

The Role of Anionogenic Elements (As, Sb, Mo, Se, S, P, N, Cl, F, C) In The Formation of Technogenic Geochemical Anomalies

NASA Astrophysics Data System (ADS)

Abrosimova, Natalya; Bortnikova, Svetlana

2017-12-01

The study was conducted on the example of sulphide-containing mine tailings with a varying amount of sulphide and arsenide minerals, from three distinct tailings dumps situated in Russia: Karabash Mine Site, South Ural; Komsomolsk tailings impoundment, Kemerovo region; Khovu-Aksy mine site, Tuva Republic. The aim of the study was to compare the mobility of anionogenic elements (As, Sb, Mo, Se, S, P, N, Cl, F, C) and their role in migration, precipitation, and concentration of metals during the water-tailings interaction depending on the physicochemical parameters (pH, Eh) of the medium and the mineral composition of the waste material. Using slightly acidic leaching experiments the quantitative estimation of mobile forms of elements is given. Based on the compositions of the obtained water leaching solutions, aqueous speciation of chemical elements and saturation index of key minerals in the experimental solutions were calculated. The results of calculating forms of chemical elements made it possible to construct series of mobility of metals and metalloids in solutions with different physicochemical parameters. In the alkaline conditions, Sb>As>Cd>Cu>Zn>Fe>Pb, when the medium is acidified, the series changes, As>Cd>Cu>Zn>Pb>Sb>Fe in weakly alkaline conditions, Sb>Mn>As>Zn>Fe however, when the medium is acidified, the series changes to Cd>Mn>Pb>Cu>Zn>Sb>Ni>Fe>As under acidic conditions Cd>Cu>Zn>Pb>Mn>Fe>Se>Mo>Sb>As>Ni. The mineral composition of the tailings was investigated, which will allow to determine the sources of toxic elements and to understand the processes of secondary mineral formation in technogenic objects. Arsenopyrite and pyrite predominate in the heavy fraction of the Komsomolsk tailings impoundment, arsenopyrite grains are often corroded, Sb contained in Sb oxide and Sb sulfide. The pyrite and barite are determined in the solid matter of the Karabash Mine Site and chalcopyrite, sphalerite, tennantite Cu3AsS3, and tetrahedrite (Cu,Fe)12Sb4S13 are

Microbiological reduction of Sb(V) in anoxic freshwater sediments

USGS Publications Warehouse

Oremland, Ronald S.; Kulp, Thomas R.; Miller, Laurence G.; Braiotta, Franco; Webb, Samuel M.; Kocar, Benjamin D; Blum, Jodi S.

2014-01-01

Microbiological reduction of millimolar concentrations of Sb(V) to Sb(III) was observed in anoxic sediments from two freshwater settings: (1) a Sb- and As-contaminated mine site (Stibnite Mine) in central Idaho and 2) an uncontaminated suburban lake (Searsville Lake) in the San Francisco Bay Area. Rates of Sb(V) reduction in anoxic sediment microcosms and enrichment cultures were enhanced by amendment with lactate or acetate as electron donors but not by H2, and no reduction occurred in sterilized controls. Addition of 2-14C-acetate to Stibnite Mine microcosms resulted in the production of 14CO2 coupled to Sb(V) reduction, suggesting that this process proceeds by a dissimilatory respiratory pathway in those sediments. Antimony(V) reduction in Searsville Lake sediments was not coupled to acetate mineralization and may be associated with Sb-resistance. The microcosms and enrichment cultures also reduced sulfate, and the precipitation of insoluble Sb(III)-sulfide complexes was a major sink for reduced Sb. The reduction of Sb(V) by Stibnite Mine sediments was inhibited by As(V), suggesting that As(V) is a preferred electron acceptor for the indigenous community. These findings indicate a novel pathway for anaerobic microbiological respiration and suggest that communities capable of reducing high concentrations of Sb(V) commonly occur naturally in the environment.

Bi-induced band gap reduction in epitaxial InSbBi alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rajpalke, M. K.; Linhart, W. M.; Yu, K. M.

2014-11-24

The properties of molecular beam epitaxy-grown InSb 1-x Bi x alloys are investigated. Rutherford backscattering spectrometry shows that the Bi content increases from 0.6% for growth at 350 °C to 2.4% at 200 °C. X-ray diffraction indicates Bi-induced lattice dilation and suggests a zinc-blende InBi lattice parameter of 6.626 Å. Scanning electron microscopy reveals surface InSbBi nanostructures on the InSbBi films for the lowest growth temperatures, Bi droplets at intermediate temperatures, and smooth surfaces for the highest temperature. The room temperature optical absorption edge was found to change from 172 meV (7.2 μm) for InSb to ~88 meV (14.1 μm)more » for InSb 0.976Bi 0.024, a reduction of ~35 meV/%Bi.« less

Monitoring Changes In Power, Speed, Agility And Endurance In Elite Cricketers During The Off-Season.

PubMed

Bishop, Chris; Herridge, Ross; Turner, Anthony

2017-06-22

The purpose of this study was to monitor changes in power, speed, agility and endurance in elite cricketers during the 20-week off-season period. Fourteen elite male cricketers (age 26.2 ± 5.3years; height 180.8 ± 8.5cm; mass 83.5 ± 6.7kg) conducted a physical testing battery in week 1 and week 18 of the off-season period. The testing included a yoyo intermittent recovery test (yoyo IRT), bilateral and unilateral countermovement jumps (CMJ), squat jump (SJ), broad jump (BJ), drop jump (to calculate reactive strength index - [RSI]), pro agility and 5, 10, 20m sprint tests. Results showed significant improvements (p < 0.05) in all fitness tests except for the pro-agility test (p = 0.076), with effect sizes ranging from 0.26-2.8 across the test battery. The results of this study show the off-season in cricket allows adequate time for significant improvements of physical qualities needed for the demanding in-season schedule of the sport and provide normative values for an elite cricket population.

Combination of COFRADIC and high temperature-extended column length conventional liquid chromatography: a very efficient way to tackle complex protein samples, such as serum.

PubMed

Sandra, Koen; Verleysen, Katleen; Labeur, Christine; Vanneste, Lies; D'Hondt, Filip; Thomas, Grégoire; Kas, Koen; Gevaert, Kris; Vandekerckhove, Joël; Sandra, Pat

2007-03-01

The previously reported COmbined FRActional DIagonal Chromatography (COFRA-DIC) methodology, in which a subset of peptides representative for their parent proteins are sorted, is particularly powerful for whole proteome analysis. This peptide-centric technology is built around diagonal chromatography, where peptide separations are crucial. This paper presents high efficiency peptide separations, in which four 250 x 2.1 mm, 5 microm Zorbax 300SB-C18 columns (total length 1 m) were coupled at operating temperatures of 60'C using a dedicated LC oven and conventional LC equipment. The high efficiency separations were combined with the COFRADIC procedure. This extremely powerful combination resulted, for the analysis of serum, in an increase in the uniquely identified peptide sequences by a factor of 2.6, compared to the COFRADIC procedure on a 25 cm column. This is a reflection of the increased peak capacity obtained on the 1 m column, which was calculated to be a factor 2.7 higher than on the 25 cm column. Besides more efficient sorting, less ion suppression was noticed.

Agile rediscovering values: Similarities to continuous improvement strategies

NASA Astrophysics Data System (ADS)

Díaz de Mera, P.; Arenas, J. M.; González, C.

2012-04-01

Research in the late 80's on technological companies that develop products of high value innovation, with sufficient speed and flexibility to adapt quickly to changing market conditions, gave rise to the new set of methodologies known as Agile Management Approach. In the current changing economic scenario, we considered very interesting to study the similarities of these Agile Methodologies with other practices whose effectiveness has been amply demonstrated in both the West and Japan. Strategies such as Kaizen, Lean, World Class Manufacturing, Concurrent Engineering, etc, would be analyzed to check the values they have in common with the Agile Approach.

Agile Task Tracking Tool

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duke, Roger T.; Crump, Thomas Vu

The work was created to provide a tool for the purpose of improving the management of tasks associated with Agile projects. Agile projects are typically completed in an iterative manner with many short duration tasks being performed as part of iterations. These iterations are generally referred to as sprints. The objective of this work is to create a single tool that enables sprint teams to manage all of their tasks in multiple sprints and automatically produce all standard sprint performance charts with minimum effort. The format of the printed work is designed to mimic a standard Kanban board. The workmore » is developed as a single Excel file with worksheets capable of managing up to five concurrent sprints and up to one hundred tasks. It also includes a summary worksheet providing performance information from all active sprints. There are many commercial project management systems typically designed with features desired by larger organizations with many resources managing multiple programs and projects. The audience for this work is the small organizations and Agile project teams desiring an inexpensive, simple, user-friendly, task management tool. This work uses standard readily available software, Excel, requiring minimum data entry and automatically creating summary charts and performance data. It is formatted to print out and resemble standard flip charts and provide the visuals associated with this type of work.« less

SU-E-T-149: Electron Beam Profile Differences Between Elekta MLCi2 and Elekta Agility Treatment Heads

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, C; Hatcher, C

2014-06-01

Purpose: To report and investigate observed differences in electron beam profiles at various energies/applicators between Elekta MLCi2 and Agility treatment head on Elekta Infinity LINAC Methods: When we upgraded from MLCi2 to Agility on one of our Elekta Infinity LINAC's, electron beam PDDs and profiles were acquired for comparison purpose. All clinical electron energies (6/9/12/15/12/18 MeV) and electron applicators (6/10/14/20/25 square) were included in measurement. PDDs were acquired at 100 SSD in water (PTW MP3 water tank) with a plane-parallel ion chamber (PTW Roos). X and Y Profiles were acquired using IC Profiler (Sun Nuclear Corp.) at 1cm and maximummore » PDD depths (water equivalent). Results: All PDD curves match very well between MLCi2 and Agility treatment head. However, some significant differences on electron profiles were found. On Agility, even after increasing the default auto-tracking offset values for backup diaphragms in Y and MLC in X by 2.8 cm (the maximum allowed change is 3.0 cm), electron profiles still have rounder shoulders comparing to corresponding MLCi2 profiles. This difference is significantly more pronounced at larger applicators (20 and 25 square), for all electron energies. Conclusion: The significant design change between MLCi2 and Agility beam limiting device seems to affect exit electron beam profiles. In IEC1217 X direction, the main change on Agility is the removal of the original MLCi2 X backup diaphragms and replacing it with MLC leaves; In Y direction, the main change is the radius and materials on Y backup diaphragms.« less

Cinnamic acid 4-hydroxylase of sorghum [Sorghum biocolor (L.) Moench] gene SbC4H1 restricts lignin synthesis in Arabidopsis

USDA-ARS?s Scientific Manuscript database

Cinnamic acid 4-hydroxylase (C4H) is the first hydroxylase enzyme of the phenylpropanoid pathway, and its content and activity affects the lignin synthesis. In this study, we isolated a C4H gene SbC4H1 from the suppression subtractive hybridization library of brown midrib (bmr) mutants of Sorghum b...

The Effects of a 6-Week Plyometric Training Program on Agility

PubMed Central

Miller, Michael G.; Herniman, Jeremy J.; Ricard, Mark D.; Cheatham, Christopher C.; Michael, Timothy J.

2006-01-01

The purpose of the study was to determine if six weeks of plyometric training can improve an athlete's agility. Subjects were divided into two groups, a plyometric training and a control group. The plyometric training group performed in a six week plyometric training program and the control group did not perform any plyometric training techniques. All subjects participated in two agility tests: T-test and Illinois Agility Test, and a force plate test for ground reaction times both pre and post testing. Univariate ANCOVAs were conducted to analyze the change scores (post - pre) in the independent variables by group (training or control) with pre scores as covariates. The Univariate ANCOVA revealed a significant group effect F2,26 = 25.42, p=0.0000 for the T-test agility measure. For the Illinois Agility test, a significant group effect F2,26 = 27.24, p = 0.000 was also found. The plyometric training group had quicker posttest times compared to the control group for the agility tests. A significant group effect F2,26 = 7.81, p = 0.002 was found for the Force Plate test. The plyometric training group reduced time on the ground on the posttest compared to the control group. The results of this study show that plyometric training can be an effective training technique to improve an athlete's agility. Key Points Plyometric training can enhance agility of athletes. 6 weeks of plyometric training is sufficient to see agility results. Ground reaction times are decreased with plyometric training PMID:24353464

Low intrinsic c-axis thermal conductivity in PVD grown epitaxial Sb2Te3 films

NASA Astrophysics Data System (ADS)

Rieger, F.; Kaiser, K.; Bendt, G.; Roddatis, V.; Thiessen, P.; Schulz, S.; Jooss, C.

2018-05-01

Accurate determination and comprehensive understanding of the intrinsic c-axis thermal conductivity κc of thermoelectric layered Sb2Te3 is of high importance for the development of strategies to optimize the figure of merit in thin film devices via heterostructures and defect engineering. We present here high precision measurements of κc of epitaxial Sb2Te3 thin films on Al2O3 substrates grown by physical vapor deposition in the temperature range of 100 K to 300 K. The Kapitza resistances of the involved interfaces have been determined and subtracted from the film data, allowing access to the intrinsic thermal conductivity of single crystalline Sb2Te3. At room temperature, we obtain κc = 1.9 W/m K, being much smaller than the in-plane thermal conductivity of κa b = 5 W/m K and even lower than the thermal conductivity of nano crystalline films of κnc ≈ 2.0-2.6 W/m K published by Park et al. [Nanoscale Res. Lett. 9, 96 (2014)]. High crystallinity and very low defect concentration of the films were confirmed by x-ray diffraction and high resolution transmission electron microscopy. Our data reveal that the phonon mean free path lm f p(" separators="|T ) is not limited by defect scattering and is of intrinsic nature, i.e., due to phonon-phonon scattering similar to other soft van der Waals type bonded layered systems.

Agile manufacturing and constraints management: a strategic perspective

NASA Astrophysics Data System (ADS)

Stratton, Roy; Yusuf, Yahaya Y.

2000-10-01

The definition of the agile paradigm has proved elusive and is often viewed as a panacea, in contention with more traditional approaches to operations strategy development and Larkin its own methodology and tools. The Theory of Constraints (TOC) is also poorly understood, as it is commonly solely associated with production planning and control systems and bottleneck management. This paper will demonstrate the synergy between these two approaches together with the Theory of Inventive Problem Solving (TRIZ), and establish how the systematic elimination of trade-offs can support the agile paradigm. Whereas agility is often seen as a trade-off free destination, both TOC and TRIZ may be considered to be route finders, as they comprise methodologies that focus on the identification and elimination of the trade-offs that constrain the purposeful improvement of a system, be it organizational or mechanical. This paper will also show how the TOC thinking process may be combined with the TRIZ knowledge based approach and used in breaking contradictions within agile logistics.

Agile methods in biomedical software development: a multi-site experience report.

PubMed

Kane, David W; Hohman, Moses M; Cerami, Ethan G; McCormick, Michael W; Kuhlmman, Karl F; Byrd, Jeff A

2006-05-30

Agile is an iterative approach to software development that relies on strong collaboration and automation to keep pace with dynamic environments. We have successfully used agile development approaches to create and maintain biomedical software, including software for bioinformatics. This paper reports on a qualitative study of our experiences using these methods. We have found that agile methods are well suited to the exploratory and iterative nature of scientific inquiry. They provide a robust framework for reproducing scientific results and for developing clinical support systems. The agile development approach also provides a model for collaboration between software engineers and researchers. We present our experience using agile methodologies in projects at six different biomedical software development organizations. The organizations include academic, commercial and government development teams, and included both bioinformatics and clinical support applications. We found that agile practices were a match for the needs of our biomedical projects and contributed to the success of our organizations. We found that the agile development approach was a good fit for our organizations, and that these practices should be applicable and valuable to other biomedical software development efforts. Although we found differences in how agile methods were used, we were also able to identify a set of core practices that were common to all of the groups, and that could be a focus for others seeking to adopt these methods.

Agile methods in biomedical software development: a multi-site experience report

PubMed Central

Kane, David W; Hohman, Moses M; Cerami, Ethan G; McCormick, Michael W; Kuhlmman, Karl F; Byrd, Jeff A

2006-01-01

Background Agile is an iterative approach to software development that relies on strong collaboration and automation to keep pace with dynamic environments. We have successfully used agile development approaches to create and maintain biomedical software, including software for bioinformatics. This paper reports on a qualitative study of our experiences using these methods. Results We have found that agile methods are well suited to the exploratory and iterative nature of scientific inquiry. They provide a robust framework for reproducing scientific results and for developing clinical support systems. The agile development approach also provides a model for collaboration between software engineers and researchers. We present our experience using agile methodologies in projects at six different biomedical software development organizations. The organizations include academic, commercial and government development teams, and included both bioinformatics and clinical support applications. We found that agile practices were a match for the needs of our biomedical projects and contributed to the success of our organizations. Conclusion We found that the agile development approach was a good fit for our organizations, and that these practices should be applicable and valuable to other biomedical software development efforts. Although we found differences in how agile methods were used, we were also able to identify a set of core practices that were common to all of the groups, and that could be a focus for others seeking to adopt these methods. PMID:16734914

Magnetic and Electrical Transport Properties of Dirac Compound BaMnSb2*

NASA Astrophysics Data System (ADS)

Huang, Silu; Kim, Jisun; Shelton, William. A.; Plummer, Ward; Jin, Rongying

BaMnSb2 is a layered compound containing Sb square nets that is theoretically predicted to host Dirac fermions. We have carried out experimental investigations on electrical transport and magnetic properties of BaMnSb2 single crystals. Both in-plane (ρab) and c-axis (ρc) resistivities show metallic behavior with a small bump in ρc located near 40 K, while there is large anisotropy ρc / ρab ( 100 at 300 K) that increases with decreasing temperature to 1500 at 2 K. Interestingly, Shubnikov-de Hass (SdH) oscillations are observed for both ρab and ρc over a wide temperature and magnetic field range. Quantitative analysis indicates that large amplitude SdH oscillations result from nearly massless Dirac Fermions. Furthermore, our magnetic measurements indicate an A-type antiferromagnetic magnetic ordering below 286 K where ferromagnetic ordering is observed in the ab plane with antiferromagnetic coupling along the c direction. These results indicate that BaMnSb2 is a 2D magnetic Dirac material. This work is supported by NSF through Grant Number DMR-1504226.

Analysis and optimization of preliminary aircraft configurations in relationship to emerging agility metrics

NASA Technical Reports Server (NTRS)

Sandlin, Doral R.; Bauer, Brent Alan

1993-01-01

This paper discusses the development of a FORTRAN computer code to perform agility analysis on aircraft configurations. This code is to be part of the NASA-Ames ACSYNT (AirCraft SYNThesis) design code. This paper begins with a discussion of contemporary agility research in the aircraft industry and a survey of a few agility metrics. The methodology, techniques and models developed for the code are then presented. Finally, example trade studies using the agility module along with ACSYNT are illustrated. These trade studies were conducted using a Northrop F-20 Tigershark aircraft model. The studies show that the agility module is effective in analyzing the influence of common parameters such as thrust-to-weight ratio and wing loading on agility criteria. The module can compare the agility potential between different configurations. In addition one study illustrates the module's ability to optimize a configuration's agility performance.

Growth mechanisms of GaSb heteroepitaxial films on Si with an AlSb buffer layer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vajargah, S. Hosseini; Botton, G. A.; Brockhouse Institute for Materials Research, McMaster University, Hamilton, Ontario L8S 4M1

2013-09-21

The initial growth stages of GaSb epilayers on Si substrates and the role of the AlSb buffer layer were studied by high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM). Heteroepitaxy of GaSb and AlSb on Si both occur by Volmer-Weber (i.e., island mode) growth. However, the AlSb and GaSb islands have distinctly different characteristics as revealed through an atomic-resolution structural study using Z-contrast of HAADF-STEM imaging. While GaSb islands are sparse and three dimensional, AlSb islands are numerous and flattened. The introduction of 3D island-forming AlSb buffer layer facilitates the nucleation of GaSb islands. The AlSb islands-assisted nucleation of GaSbmore » islands results in the formation of drastically higher quality planar film at a significantly smaller thickness of films. The interface of the AlSb and GaSb epilayers with the Si substrate was further investigated with energy dispersive X-ray spectrometry to elucidate the key role of the AlSb buffer layer in the growth of GaSb epilayers on Si substrates.« less

Density functional simulations of Sb-rich GeSbTe phase change alloys.

PubMed

Gabardi, S; Caravati, S; Bernasconi, M; Parrinello, M

2012-09-26

We generated models of the amorphous phase of Sb-rich GeSbTe phase change alloys by quenching from the melt within density functional molecular dynamics. We considered the two compositions Ge(1)Sb(1)Te(1) and Ge(2)Sb(4)Te(5). Comparison with previous results on the most studied Ge(2)Sb(2)Te(5) allowed us to draw some conclusions on the dependence of the structural properties of the amorphous phase on the alloy composition. Vibrational and electronic properties were also scrutinized. Phonons at high frequencies above 200 cm(-1) are localized in tetrahedra around Ge atoms in Sb-rich compounds as well as in Ge(2)Sb(2)Te(5). All compounds are semiconducting in the amorphous phase, with a band gap in the range 0.7-1.0 eV.

Density functional simulations of Sb-rich GeSbTe phase change alloys

NASA Astrophysics Data System (ADS)

Gabardi, S.; Caravati, S.; Bernasconi, M.; Parrinello, M.

2012-09-01

We generated models of the amorphous phase of Sb-rich GeSbTe phase change alloys by quenching from the melt within density functional molecular dynamics. We considered the two compositions Ge1Sb1Te1 and Ge2Sb4Te5. Comparison with previous results on the most studied Ge2Sb2Te5 allowed us to draw some conclusions on the dependence of the structural properties of the amorphous phase on the alloy composition. Vibrational and electronic properties were also scrutinized. Phonons at high frequencies above 200 cm-1 are localized in tetrahedra around Ge atoms in Sb-rich compounds as well as in Ge2Sb2Te5. All compounds are semiconducting in the amorphous phase, with a band gap in the range 0.7-1.0 eV.

Software ``Best'' Practices: Agile Deconstructed

NASA Astrophysics Data System (ADS)

Fraser, Steven

This workshop will explore the intersection of agility and software development in a world of legacy code-bases and large teams. Organizations with hundreds of developers and code-bases exceeding a million or tens of millions of lines of code are seeking new ways to expedite development while retaining and attracting staff who desire to apply “agile” methods. This is a situation where specific agile practices may be embraced outside of their usual zone of applicability. Here is where practitioners must understand both what “best practices” already exist in the organization - and how they might be improved or modified by applying “agile” approaches.

DETERMINATION OF AZOXYSTROBIN AND DIFENOCONAZOLE IN PESTICIDE PRODUCTS.

PubMed

Lazić, S; Šunjka, D

2015-01-01

In this study a high performance liquid chromatographic (HPLC-DAD) procedure has been developed for the simultaneous determination of azoxystrobin and difenoconazole in suspension concentrate pesticide formulations, with the aim of the product quality control. Azoxystrobin, strobilurin fungicide and difenoconazole (cis,trans-3-chloro-4-[4-methyl-2-(1H-1,2,4-triazol-1-ylmethyl)-1,3-dioxolan-2-yl]phenyl 4-chlorophenyl ether), triazole fungicide, are used for the protection of plants from wide spectrum of fungal diseases. For the analysis LC system an Agilent Technologies 1100 Series was used. Good separation was achieved on a Zorbax SB-C18 column (5 μm, 250 mm x 3 mm internal diameter) using a mobile phase consisting of acetonitrile/ultrapure water (90:10, v/v), at a flow rate of 0.9 ml/minute and UV detection at 218 nm. Column temperature was 25 degrees C, injected volume was 1 μl. Retention times for azoxystrobin and difenoconazole were 2.504 min and 1.963 min, respectively. This method is validated according to the requirements for new methods, which include linearity, precision, accuracy and selectivity. The method demonstrates good linearity with r2 > 0.997. The repeatability of the method, expressed as relative standard deviation (RSD, %), was found to be 1.9% for azoxystrobin and 0.5% for difenoconazole. The precision of the method was also considered to be acceptable as the experimental repeatability relative standard deviation (RSD) was lower than the RSD calculated using the Horwitz equation of 1.7% and 1.4% for azoxystrobin and difenoconazole, respectively. The accuracy of the proposed method was determined from recovery experiments through standard addition procedure. The average recoveries of the three fortification levels were 101.9% for azoxystrobin and 103.2% for difenoconazole with RSDs of 1.1% and 1.2%. The method described in this paper is simple, precise, accurate and selective and represents a new and reliable way of simultaneous determination

MOVPE of GaSb/InGaAsSb Multilayers and Fabrication of Dual Band Photodetectors

NASA Technical Reports Server (NTRS)

Xiao, Ye-Gao; Bhat, Ishwara; Refaat, Tamer F.; Abedin, M. Nurul; Shao, Qing-Hui

2005-01-01

Metalorganic vapor phase epitaxy (MOVPE) of GaSb/InGaAsSb multilayer thin films and fabrication of bias-selectable dual band photodetectors are reported. For the dual band photodetectors the short wavelength detector, or the upper p- GaSb/n-GaSb junction photodiode, is placed optically ahead of the long wavelength one, or the lower photodiode. The latter is based on latticed-matched In0.13Ga0.87As0.11Sb0.89 with bandgap near 0.6 eV. Specifically, high quality multilayer thin films are grown sequentially from top to bottom as p+-GaSb/p-GaSb/n-GaSb/n-InGaAsSb/p-InGaAsSb/p-GaSb on undoped p-type GaSb substrate, and as n-GaSb/p-GaSb/p-InGaAsSb/n-InGaAsSb/n-GaSb on Te-doped n-type GaSb substrate respectively. The multilayer thin films are characterized by optical microscope, atomic force microscope (AFM), electron microprobe analyses etc. The photodiode mesa steps are patterned by photolithography with wet chemical etching and the front metallization is carried out by e-beam evaporation with Pd/Ge/Au/Ti/Au to give ohmic contact on both n- and p-type Sb based layer surfaces. Dark I-V measurements show typical diode behavior for both the upper and lower photodiodes. The photoresponsivity measurements indicate that both the upper and lower photodiodes can sense the infrared illumination corresponding to their cutoff wavelengths respectively, comparable with the simulation results. More work is underway to bring the long wavelength band to the medium infrared wavelength region near 4 micrometers.

Creating IT agility.

PubMed

Glaser, John

2008-04-01

Seven steps healthcare organizations can take to improve IT agility are: Pay attention to the capabilities of IT applications. Establish short project phases. Stage the release of capital and new IT positions. Cross-train IT staff. Adopt technology standards. Shorten IT plan time horizons. Align IT with organizational strategies and priorities.

Architected Agile Solutions for Software-Reliant Systems

NASA Astrophysics Data System (ADS)

Boehm, Barry; Lane, Jo Ann; Koolmanojwong, Supannika; Turner, Richard

Systems are becoming increasingly reliant on software due to needs for rapid fielding of “70% capabilities,” interoperability, net-centricity, and rapid adaptation to change. The latter need has led to increased interest in agile methods of software development, in which teams rely on shared tacit interpersonal knowledge rather than explicit documented knowledge. However, such systems often need to be scaled up to higher level of performance and assurance, requiring stronger architectural support. Several organizations have recently transformed themselves by developing successful combinations of agility and architecture that can scale to projects of up to 100 personnel. This chapter identifies a set of key principles for such architected agile solutions for software-reliant systems, provides guidance for how much architecting is enough, and illustrates the key principles with several case studies.

Effect of Se substitution on the phase change properties of Ge2Sb2Te5

NASA Astrophysics Data System (ADS)

Shekhawat, Roopali; Rangappa, Ramanna; Gopal, E. S. R.; Ramesh, K.

2018-05-01

Ge2Sb2Te5 popularly known as GST is being explored for non-volatile phase change random access memory(PCRAM) applications. Under high electric field, thin films of amorphous GST undergo a phase change from amorphous to crystalline with a high contrast in electrical resistivity (about 103). The phase change is between amorphous and metastable NaCl structure occurs at about 150°C and not to the stable hexagonal phase which occurs at a high temperature (> 250 °C). In GST, about 50 % of Te substituted by Se (Ge2Sb2Te2.5Se2.5) is found to increase the contrast in electrical resistivity by 7 orders of magnitude (about 4 orders of magnitude higher than GST). The phase transition in Se added GST also found to be between amorphous and the stable hexagonal structure. The threshold voltage at which the Ge2Sb2Te2.5Se2.5 switches to the high conducting state increases to 9V as compared to 2V in GST. Interestingly, the threshold current decrease to 1mA as compared to 1.8mA in GST indicating the Se substitution reduces the power needed for switching between the low and high conducting states. The reduction in power needed for phase change, high contrast in electrical resistivity with high thermal stability makes Ge2Sb2Te2.5Se2.5 as a better candidate for PCRAM.

Reactive Agility Performance in Handball; Development and Evaluation of a Sport-Specific Measurement Protocol

PubMed Central

Spasic, Miodrag; Krolo, Ante; Zenic, Natasa; Delextrat, Anne; Sekulic, Damir

2015-01-01

There is no current study that examined sport-specific tests of reactive-agility and change-of-direction-speed (CODS) to replicate real-sport environment in handball (team-handball). This investigation evaluated the reliability and validity of two novel tests designed to assess reactive-agility and CODS of handball players. Participants were female (25.14 ± 3.71 years of age; 1.77 ± 0.09 m and 74.1 ± 6.1 kg) and male handball players (26.9 ± 4.1 years of age; 1.90 ± 0.09 m and 93.90±4.6 kg). Variables included body height, body mass, body mass index, broad jump, 5-m sprint, CODS and reactive-agility tests. Results showed satisfactory reliability for reactive-agility-test and CODS-test (ICC of 0.85-0.93, and CV of 2.4-4.8%). The reactive-agility and CODS shared less than 20% of the common variance. The calculated index of perceptual and reactive capacity (P&RC; ratio between reactive-agility- and CODS-performance) is found to be valid measure in defining true-game reactive-agility performance in handball in both genders. Therefore, the handball athletes’ P&RC should be used in the evaluation of real-game reactive-agility performance. Future studies should explore other sport-specific reactive-agility tests and factors associated to such performance in sports involving agile maneuvers. Key points Reactive agility and change-of-direction-speed should be observed as independent qualities, even when tested over the same course and similar movement template The reactive-agility-performance of the handball athletes involved in defensive duties is closer to their non-reactive-agility-score than in their peers who are not involved in defensive duties The handball specific “true-game” reactive-agility-performance should be evaluated as the ratio between reactive-agility and corresponding CODS performance. PMID:26336335

Reactive Agility Performance in Handball; Development and Evaluation of a Sport-Specific Measurement Protocol.

PubMed

Spasic, Miodrag; Krolo, Ante; Zenic, Natasa; Delextrat, Anne; Sekulic, Damir

2015-09-01

There is no current study that examined sport-specific tests of reactive-agility and change-of-direction-speed (CODS) to replicate real-sport environment in handball (team-handball). This investigation evaluated the reliability and validity of two novel tests designed to assess reactive-agility and CODS of handball players. Participants were female (25.14 ± 3.71 years of age; 1.77 ± 0.09 m and 74.1 ± 6.1 kg) and male handball players (26.9 ± 4.1 years of age; 1.90 ± 0.09 m and 93.90±4.6 kg). Variables included body height, body mass, body mass index, broad jump, 5-m sprint, CODS and reactive-agility tests. Results showed satisfactory reliability for reactive-agility-test and CODS-test (ICC of 0.85-0.93, and CV of 2.4-4.8%). The reactive-agility and CODS shared less than 20% of the common variance. The calculated index of perceptual and reactive capacity (P&RC; ratio between reactive-agility- and CODS-performance) is found to be valid measure in defining true-game reactive-agility performance in handball in both genders. Therefore, the handball athletes' P&RC should be used in the evaluation of real-game reactive-agility performance. Future studies should explore other sport-specific reactive-agility tests and factors associated to such performance in sports involving agile maneuvers. Key pointsReactive agility and change-of-direction-speed should be observed as independent qualities, even when tested over the same course and similar movement templateThe reactive-agility-performance of the handball athletes involved in defensive duties is closer to their non-reactive-agility-score than in their peers who are not involved in defensive dutiesThe handball specific "true-game" reactive-agility-performance should be evaluated as the ratio between reactive-agility and corresponding CODS performance.

AlInAsSb for GaSb-based multi-junction solar cells

NASA Astrophysics Data System (ADS)

Tournet, J.; Rouillard, Y.; Tournié, E.

2018-02-01

Bandgap engineering, by means of alloying or inserting nanostructures, is the bedrock of high efficiency photovoltaics. III-V quaternary alloys in particular enable bandgap tailoring of a multi-junction subcell while conserving a single lattice parameter. Among the possible candidates, AlInAsSb could in theory reach the widest range of bandgap energies while being lattice-matched to InP or GaSb. Although these material systems are still emerging photovoltaic segments, they do offer advantages for multi-junction design. GaSbbased structures in particular can make use of highly efficient GaSb/InAs tunnel junctions to connect the subcells. There has been only little information concerning GaSb-lattice matched AlInAsSb in the literature. The alloy's miscibility gap can be circumvented by the use of non-equilibrium techniques. Nevertheless, appropriate growth conditions remain to be found in order to produce a stable alloy. Furthermore, the abnormally low bandgap energies reported for the material need to be confirmed and interpreted with a multi-junction perspective. In this work, we propose a tandem structure made of an AlInAsSb top cell and a GaSb bottom cell. An epitaxy study of the AlInAsSb alloy lattice-matched to GaSb was first performed. The subcells were then grown and processed. The GaSb subcell yielded an efficiency of 5.9% under 1 sun and the tandem cell is under optimization. Preliminary results are presented in this document.

Relationship between agility and lower limb muscle strength, targeting university badminton players.

PubMed

Sonoda, Takuya; Tashiro, Yuto; Suzuki, Yusuke; Kajiwara, Yu; Zeidan, Hala; Yokota, Yuki; Kawagoe, Mirei; Nakayama, Yasuaki; Bito, Tsubasa; Shimoura, Kanako; Tatsumi, Masataka; Nakai, Kengo; Nishida, Yuichi; Yoshimi, Soyoka; Aoyama, Tomoki

2018-02-01

[Purpose] Targeting university badminton players, this study investigated the relationship between agility, which is associated with performance in badminton, and lower limb muscle strength, and examined which muscles influence agility. [Subjects and Methods] A total of 23 male university badminton players were evaluated for side-shuffle test scores and lower limb strength. The relationships between agility, lower limb strength, and duration of experience playing badminton were evaluated using a correlation analysis. Moreover, the relationship between agility and lower limb strength was evaluated by partial correlation analysis, adjusting for the effects of experience of each badminton player. [Results] The agility score correlated with hip extension and ankle plantar flexion strength, with adjustment for badminton experience. [Conclusion] This study suggests that hip extension training and improvement in ankle plantar flexion strength may improve agility.

Investigation of regime switching from mode locking to Q-switching in a 2 µm InGaSb/AlGaAsSb quantum well laser.

PubMed

Li, Xiang; Wang, Hong; Qiao, Zhongliang; Guo, Xin; Wang, Wanjun; Ng, Geok Ing; Zhang, Yu; Xu, Yingqiang; Niu, Zhichuan; Tong, Cunzhu; Liu, Chongyang

2018-04-02

A two-section InGaSb/AlGaAsSb single quantum well (SQW) laser emitting at 2 μm is presented. By varying the absorber bias voltage with a fixed gain current at 130 mA, passive mode locking at ~18.40 GHz, Q-switched mode locking, and passive Q-switching are observed in this laser. In the Q-switched mode locking regimes, the Q-switched RF signal and mode locked RF signal coexist, and the Q-switched lasing and mode-locked lasing happen at different wavelengths. This is the first observation of these three pulsed working regimes in a GaSb-based diode laser. An analysis of the regime switching mechanism is given based on the interplay between the gain saturation and the saturable absorption.

High performance Sb2S3/carbon composite with tailored artificial interface as an anode material for sodium ion batteries

NASA Astrophysics Data System (ADS)

Choi, Jeong-Hee; Ha, Chung-Wan; Choi, Hae-Young; Shin, Heon-Cheol; Lee, Sang-Min

2017-11-01

The electrochemical comparison between Sb2S3 and its composite with carbon (Sb2S3/C) involved by sodium ion carrier are explained by enhanced kinetics, particularly with respect to improved interfacial conductivity by surface modulation by carbon. Sb2S3 and Sb2S3/C are synthesized by a high energy mechanical milling process. The successful synthesis of these materials is confirmed with X-ray diffraction (XRD), scanning electron microscopy, and transmission electron microscopy (TEM). As an anode material for sodium ion batteries, Sb2S3 exhibits an initial sodiation/desodiation capacity of 1,021/523 mAh g-1 whereas the Sb2S3/C composite exhibits a higher reversible capacity (642 mAh g-1). Furthermore, the cycle performance and rate capability of the Sb2S3/C composite are estimated to be much better than those of Sb and Sb2S3. Electrochemical impedance spectroscopy analysis shows that the Sb2S3/C composite exhibited charge transfer resistance and surface film resistance much lower than Sb2S3. X-ray photoelectron spectroscopy analyses of both electrodes demonstrate that NaF layer on Sb2S3/C composite electrode leads to the better electrochemical performances. In order to clarify the electrochemical reaction mechanism, ex-situ XRD based on differential capacity plots and ex-situ HR-TEM analyses of the Sb2S3/C composite electrode are carried out and its reaction mechanism was established.

40 CFR 721.3025 - Fatty acids C12-18, C18 unsaturated, C12-18 alkyl esters (generic).

Code of Federal Regulations, 2010 CFR

2010-07-01

..., C12-18 alkyl esters (generic). 721.3025 Section 721.3025 Protection of Environment ENVIRONMENTAL... communication program. A significant new use of these substances is any manner or method of manufacture, import, or processing associated with any use of these substances without providing risk notification as...

The 5-HT₂C receptor agonist, lorcaserin, and the 5-HT₆ receptor antagonist, SB-742457, promote satiety; a microstructural analysis of feeding behaviour.

PubMed

Higgs, Suzanne; Cooper, Alison J; Barnes, Nicholas M

2016-02-01

Whilst the FDA-approved anorectic, lorcaserin and various 5-hydroxytryptamine (5-HT)6 receptor antagonists reduce feeding, a direct assessment of their impact upon feeding behaviour is less clear. We therefore examined the action of lorcaserin and the clinical-stage developmental candidate 5-HT6 receptor antagonist, SB-742457, upon microstructural analysis of licking behaviour. Such analysis provides a rich source of information about the mechanisms controlling food intake. The objective of the present study was to gain insight into the influence upon feeding behaviour of the 5-HT2C receptor agonist, lorcaserin and the developmental 5-HT6 receptor antagonist, SB-742457. The impact of lorcaserin and SB-742457 upon licking behaviour of non-deprived rats for a glucose solution was assessed using microstructural analysis. Lorcaserin (0.1-3.0 mg/kg) displayed a dose-dependent ability to reduce glucose consumption via reduction in the number of bouts of licking. A similar action was evident with SB-742457, but only at the lowest dose tested (3.0 mg/kg). The behavioural actions of both lorcaserin and SB-742457 demonstrate they directly promote satiety.

Thinking Outside the Box: Agile Business Models for CNOs

NASA Astrophysics Data System (ADS)

Loss, Leandro; Crave, Servane

This paper introduces the idea of an agile Business Model for CNOs grounded on a new model of innovation based on the effects of globalization and of Knowledge Economy. The agile Business Model considers the resources that are spread out and available worldwide as well as the need for each customer to receive a unique customer experience. It aims at reinforcing in the context of the Knowledge Economy the different business models approaches developed so far. The paper also identifies the levers and the barriers of Agile Business Models Innovation in CNOs.

Control design for future agile fighters

NASA Technical Reports Server (NTRS)

Murphy, Patrick C.; Davidson, John B.

1991-01-01

The CRAFT control design methodology is presented. CRAFT stands for the design objectives addressed, namely, Control power, Robustness, Agility, and Flying Qualities Tradeoffs. The approach combines eigenspace assignment, which allows for direct specification of eigenvalues and eigenvectors, and a graphical approach for representing control design metrics that captures numerous design goals in one composite illustration. The methodology makes use of control design metrics from four design objective areas, namely, control power, robustness, agility, and flying qualities. An example of the CRAFT methodology as well as associated design issues are presented.

Two-band superlinear electroluminescence in GaSb based nanoheterostructures with AlSb/InAs{sub 1−x} Sb{sub x}/AlSb deep quantum well

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mikhailova, M. P.; Ivanov, E. V.; Danilov, L. V.

2014-06-14

We report on superlinear electroluminescent structures based on AlSb/InAs{sub 1−x}Sb{sub x}/AlSb deep quantum wells grown by MOVPE on n-GaSb:Te substrates. Dependence of the electroluminescence (EL) spectra and optical power on the drive current in nanoheterostructures with AlSb/InAs{sub 1−x}Sb{sub x}/AlSb quantum well at 77–300 K temperature range was studied. Intensive two-band superlinear EL in the 0.5–0.8 eV photon energy range was observed. Optical power enhancement with the increasing drive current at room temperature is caused by the contribution of the additional electron-hole pairs due to the impact ionization by the electrons heated at the high energy difference between AlSb and the first electronmore » level E{sub e1} in the InAsSb QW. Study of the EL temperature dependence at 90–300 K range enabled us to define the role of the first and second heavy hole levels in the radiative recombination process. It was shown that with the temperature decrease, the relation between the energies of the valence band offset and the second heavy hole energy level changes due to the temperature transformation of the energy band diagram. That is the reason why the EL spectrum revealed radiative transitions from the first electron level E{sub e1} to the first hole level E{sub h1} in the whole temperature range (90–300 K), while the emission band related with the transitions to the second hole level occurred only at T > 200 K. Comparative examination of the nanostructures with high band offsets and different interface types (AlAs-like and InSb-like) reveals more intense EL and optical power enhancement at room temperature in the case of AlAs-like interface that could be explained by the better quality of the heterointerface and more efficient hole localization.« less

On the Biomimetic Design of Agile-Robot Legs

PubMed Central

Garcia, Elena; Arevalo, Juan Carlos; Muñoz, Gustavo; Gonzalez-de-Santos, Pablo

2011-01-01

The development of functional legged robots has encountered its limits in human-made actuation technology. This paper describes research on the biomimetic design of legs for agile quadrupeds. A biomimetic leg concept that extracts key principles from horse legs which are responsible for the agile and powerful locomotion of these animals is presented. The proposed biomimetic leg model defines the effective leg length, leg kinematics, limb mass distribution, actuator power, and elastic energy recovery as determinants of agile locomotion, and values for these five key elements are given. The transfer of the extracted principles to technological instantiations is analyzed in detail, considering the availability of current materials, structures and actuators. A real leg prototype has been developed following the biomimetic leg concept proposed. The actuation system is based on the hybrid use of series elasticity and magneto-rheological dampers which provides variable compliance for natural motion. From the experimental evaluation of this prototype, conclusions on the current technological barriers to achieve real functional legged robots to walk dynamically in agile locomotion are presented. PMID:22247667

On the biomimetic design of agile-robot legs.

PubMed

Garcia, Elena; Arevalo, Juan Carlos; Muñoz, Gustavo; Gonzalez-de-Santos, Pablo

2011-01-01

The development of functional legged robots has encountered its limits in human-made actuation technology. This paper describes research on the biomimetic design of legs for agile quadrupeds. A biomimetic leg concept that extracts key principles from horse legs which are responsible for the agile and powerful locomotion of these animals is presented. The proposed biomimetic leg model defines the effective leg length, leg kinematics, limb mass distribution, actuator power, and elastic energy recovery as determinants of agile locomotion, and values for these five key elements are given. The transfer of the extracted principles to technological instantiations is analyzed in detail, considering the availability of current materials, structures and actuators. A real leg prototype has been developed following the biomimetic leg concept proposed. The actuation system is based on the hybrid use of series elasticity and magneto-rheological dampers which provides variable compliance for natural motion. From the experimental evaluation of this prototype, conclusions on the current technological barriers to achieve real functional legged robots to walk dynamically in agile locomotion are presented.

Sequential and simultaneous adsorption of Sb(III) and Sb(V) on ferrihydrite: Implications for oxidation and competition.

PubMed

Qi, Pengfei; Pichler, Thomas

2016-02-01

Antimony (Sb) is a naturally occurring element of growing environmental concern whose toxicity, adsorption behavior and other chemical properties are similar to that of arsenic (As). However, less is known about Sb compared to As. Individual and simultaneous adsorption experiments with Sb(III) and Sb(V) were conducted in batch mode with focus on the Sb speciation of the remaining liquid phase during individual Sb(III) adsorption experiments. The simultaneous adsorption and oxidation of Sb(III) was confirmed by the appearance of Sb(V) in the solution at varying Fe/Sb ratios (500, 100 and 8) and varying pH values (3.8, 7 and 9). This newly formed Sb(V) was subsequently removed from solution at a Fe/Sb ratio of 500 or at a pH of 3.8. However, more or less only Sb(V) was observed in the liquid phase at the end of the experiments at lower Fe/Sb ratios and higher pH, indicating that competition took place between the newly formed Sb(V) and Sb(III), and that Sb(III) outcompeted Sb(V). This was independently confirmed by simultaneous adsorption experiments of Sb(III) and Sb(V) in binary systems. Under such conditions, the presence of Sb(V) had no influence on the adsorption of Sb(III) while Sb(V) adsorption was significantly inhibited by Sb(III) over a wide pH range (4-10). Thus, in the presence of ferrihydrite and under redox conditions, which allow the presence of both Sb species, Sb(V) should be the dominant species in aquatic environments, since Sb(III) is adsorbed preferentially and at the same time oxidized to Sb(V). Copyright © 2015 Elsevier Ltd. All rights reserved.

ZnS-Sb2S3@C Core-Double Shell Polyhedron Structure Derived from Metal-Organic Framework as Anodes for High Performance Sodium Ion Batteries.

PubMed

Dong, Shihua; Li, Caixia; Ge, Xiaoli; Li, Zhaoqiang; Miao, Xianguang; Yin, Longwei

2017-06-27

Taking advantage of zeolitic imidazolate framework (ZIF-8), ZnS-Sb 2 S 3 @C core-double shell polyhedron structure is synthesized through a sulfurization reaction between Zn 2+ dissociated from ZIF-8 and S 2- from thioacetamide (TAA), and subsequently a metal cation exchange process between Zn 2+ and Sb 3+ , in which carbon layer is introduced from polymeric resorcinol-formaldehyde to prevent the collapse of the polyhedron. The polyhedron composite with a ZnS inner-core and Sb 2 S 3 /C double-shell as anode for sodium ion batteries (SIBs) shows us a significantly improved electrochemical performance with stable cycle stability, high Coulombic efficiency and specific capacity. Peculiarly, introducing a carbon shell not only acts as an important protective layer to form a rigid construction and accommodate the volume changes, but also improves the electronic conductivity to optimize the stable cycle performance and the excellent rate property. The architecture composed of ZnS inner core and a complex Sb 2 S 3 /C shell not only facilitates the facile electrolyte infiltration to reduce the Na-ion diffusion length to improve the electrochemical reaction kinetics, but also prevents the structure pulverization caused by Na-ion insertion/extraction. This approach to prepare metal sulfides based on MOFs can be further extended to design other nanostructured systems for high performance energy storage devices.

Understanding Organizational Agility: A Work-Design Perspective

DTIC Science & Technology

2008-06-01

NG SDG Proactive Yes Yes Yes Yes Yes Yes N/S N/S N/S Reactive Simultaneity of work design at three levels Yes Supply Chain Network Agility High Table...firm can take effective action to benefit itself and its customers. In analyzing representative supply - chain definitions of agility, the main theme...and Heppard 2000). Third, as effective supply chain management has come to be regarded as major source of competitive advantage for many firms

Investigation of directionally solidified InGaSb ternary alloys from Ga and Sb faces of GaSb(111) under prolonged microgravity at the International Space Station

PubMed Central

Nirmal Kumar, Velu; Arivanandhan, Mukannan; Rajesh, Govindasamy; Koyama, Tadanobu; Momose, Yoshimi; Sakata, Kaoruho; Ozawa, Tetsuo; Okano, Yasunori; Inatomi, Yuko; Hayakawa, Yasuhiro

2016-01-01

InGaSb ternary alloys were grown from GaSb (111)A and B faces (Ga and Sb faces) under microgravity conditions on board the International Space Station by a vertical gradient freezing method. The dissolution process of the Ga and Sb faces of GaSb and orientation-dependent growth properties of InGaSb were analysed. The dissolution of GaSb(111)B was greater than that of (111)A, which was found from the remaining undissolved seed and feed crystals. The higher dissolution of the Sb face was explained based on the number of atoms at that face, and its bonding with the next atomic layer. The growth interface shape was almost flat in both cases. The indium composition in both InGaSb samples was uniform in the radial direction and it gradually decreased along the growth direction because of segregation. The growth rate of InGaSb from GaSb (111)B was found to be higher than that of GaSb (111)A because of the higher dissolution of GaSb (111)B. PMID:28725736

Investigation of directionally solidified InGaSb ternary alloys from Ga and Sb faces of GaSb(111) under prolonged microgravity at the International Space Station.

PubMed

Nirmal Kumar, Velu; Arivanandhan, Mukannan; Rajesh, Govindasamy; Koyama, Tadanobu; Momose, Yoshimi; Sakata, Kaoruho; Ozawa, Tetsuo; Okano, Yasunori; Inatomi, Yuko; Hayakawa, Yasuhiro

2016-01-01

InGaSb ternary alloys were grown from GaSb (111)A and B faces (Ga and Sb faces) under microgravity conditions on board the International Space Station by a vertical gradient freezing method. The dissolution process of the Ga and Sb faces of GaSb and orientation-dependent growth properties of InGaSb were analysed. The dissolution of GaSb(111)B was greater than that of (111)A, which was found from the remaining undissolved seed and feed crystals. The higher dissolution of the Sb face was explained based on the number of atoms at that face, and its bonding with the next atomic layer. The growth interface shape was almost flat in both cases. The indium composition in both InGaSb samples was uniform in the radial direction and it gradually decreased along the growth direction because of segregation. The growth rate of InGaSb from GaSb (111)B was found to be higher than that of GaSb (111)A because of the higher dissolution of GaSb (111)B.

Synthesis and Optimization of Thermoelectric Properties of Zn(x)Sb3

NASA Technical Reports Server (NTRS)

Doan-Nguyen, Vicky V.

2005-01-01

High-performance thermoelectric materials are studied to investigate their abilities to optimize electrical and minimize thermal conductivities. A stoichiometric range of p-type zinc antimonide compounds was synthesized to analyze the trends in their thermoelectric properties. Zn(x)Sb3 (x=3.80, 3.85, 3.90, 3.95, 4.00, 4.05, 4.10) was reacted at 750 C and annealed at 300 C for 24 hours at each temperature. Electronic transport properties such as Seebeck and Hall Effect were measured to analyze possible trends in the set of compositions. SEM, EDS, and XRD were used to quantify both ingots and hot-pressed samples to confirm that they were single-phase and of the expected stoichiometries. Recent SEM data indicated that Zn(3.90)Sb3 and Zn(4.00)Sb3 samples were actually Zn3Sb2. In hopes of further improving the figure-of-merit (ZT) of the binary system, V, Cr, Mn, Fe, Co, In, and Sn were used to dope (Zn(0.95)M(0.05))(3.95)Sb3.

Enhanced Hole Mobility and Density in GaSb Quantum Wells

DTIC Science & Technology

2013-01-01

Keywords: Molecular beam epitaxy Quantum wells Semiconducting III–V materials Field-effect transistors GaSb a b s t r a c t Modulation-doped quantum wells...QWs) of GaSb clad by AlAsSb were grown by molecular beam epitaxy on InP substrates. By virtue of quantum confinement and compressive strain of the...heterostructures studied here are grown by molecular beam epitaxy (MBE) on semi-insulating (001) InP substrates using a Riber Compact 21T MBE system. A cross

78 FR 64019 - Manufacturer of Controlled Substances; Notice of Registration; Agilent Technologies

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-25

...; Notice of Registration; Agilent Technologies By Notice dated May 24, 2013, and published in the Federal Register on June 4, 2013, 78 FR 33441, Agilent Technologies, 25200 Commercentre Drive, Lake Forest... of Agilent Technologies to manufacture the listed basic classes of controlled substances is...

Peculiarities of thermoelectric half-Heusler phase formation in Gd-Ni-Sb and Lu-Ni-Sb ternary systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Romaka, V.V., E-mail: romakav@lp.edu.ua; Romaka, L.; Horyn, A.

The phase equilibria in the Gd–Ni–Sb and Lu-Ni-Sb ternary systems were studied at 873 K by X-ray and metallographic analyses in the whole concentration range. The interaction of the elements in the Gd–Ni–Sb system results the formation of five ternary compounds at investigated temperature: Gd{sub 5}Ni{sub 2}Sb (Mo{sub 5}SiB{sub 2}-type), Gd{sub 5}NiSb{sub 2} (Yb{sub 5}Sb{sub 3}-type), GdNiSb (MgAgAs-type), Gd{sub 3}Ni{sub 6}Sb{sub 5} (Y{sub 3}Ni{sub 6}Sb{sub 5}-type), and GdNi{sub 0.72}Sb{sub 2} (HfCuSi{sub 2}-type). At investigated temperature the Lu-Ni-Sb system is characterized by formation of the LuNiSb (MgAgAs-type), Lu{sub 5}Ni{sub 2}Sb (Mo{sub 5}SiB{sub 2}-type), and Lu{sub 5}Ni{sub 0.56}Sb{sub 2.44} (Yb{sub 5}Sb{sub 3}-type)more » compounds. The disordering in the crystal structure of half-Heusler GdNiSb and LuNiSb was revealed by EPMA and studied by means of Rietveld refinement and DFT modeling. The performed electronic structure calculations are in good agreement with electrical transport property studies. - Graphical abstract: Crystal structure model and electron localization function of Lu{sub 5}Ni{sub 2}Sb. Display Omitted - Highlights: • Gd-Ni-Sb and Lu-Ni-Sb phase diagrams were constructed at 873 K. • GdNiSb and LuNiSb are characterized by disordered crystal structure. • Crystal structure optimization with DFT calculations confirmed crystal structure disorder in GdNiSb and LuNiSb.« less

Synthesis, Structure, Te Alloying, and Physical Properties of CuSbS 2

DOE PAGES

Hobbis, Dean; Wei, Kaya; Wang, Hsin; ...

2017-10-30

Materials with very low thermal conductivities continue to be of interest for a variety of applications. In this paper, we synthesized CuSbS 2 employing a mechanical alloying technique in order to investigate its physical properties. The trigonal pyramid arrangement of the S atoms around the Sb atoms allows for lone-pair electron formation that results in very low thermal conductivity. Finally, in addition to thermal properties, the structural, electrical, and optical properties, as well as compositional stability measurements, are also discussed. CuSbS 1.8Te 0.2 was similarly synthesized and characterized in order to compare its structural and transport properties with that ofmore » CuSbS 2, in addition to investigating the effect of Te alloying on these properties.« less

Synthesis, Structure, Te Alloying, and Physical Properties of CuSbS 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hobbis, Dean; Wei, Kaya; Wang, Hsin

Materials with very low thermal conductivities continue to be of interest for a variety of applications. In this paper, we synthesized CuSbS 2 employing a mechanical alloying technique in order to investigate its physical properties. The trigonal pyramid arrangement of the S atoms around the Sb atoms allows for lone-pair electron formation that results in very low thermal conductivity. Finally, in addition to thermal properties, the structural, electrical, and optical properties, as well as compositional stability measurements, are also discussed. CuSbS 1.8Te 0.2 was similarly synthesized and characterized in order to compare its structural and transport properties with that ofmore » CuSbS 2, in addition to investigating the effect of Te alloying on these properties.« less

Towards seamless workflows in agile data science

NASA Astrophysics Data System (ADS)

Klump, J. F.; Robertson, J.

2017-12-01

Agile workflows are a response to projects with requirements that may change over time. They prioritise rapid and flexible responses to change, preferring to adapt to changes in requirements rather than predict them before a project starts. This suits the needs of research very well because research is inherently agile in its methodology. The adoption of agile methods has made collaborative data analysis much easier in a research environment fragmented across institutional data stores, HPC, personal and lab computers and more recently cloud environments. Agile workflows use tools that share a common worldview: in an agile environment, there may be more that one valid version of data, code or environment in play at any given time. All of these versions need references and identifiers. For example, a team of developers following the git-flow conventions (github.com/nvie/gitflow) may have several active branches, one for each strand of development. These workflows allow rapid and parallel iteration while maintaining identifiers pointing to individual snapshots of data and code and allowing rapid switching between strands. In contrast, the current focus of versioning in research data management is geared towards managing data for reproducibility and long-term preservation of the record of science. While both are important goals in the persistent curation domain of the institutional research data infrastructure, current tools emphasise planning over adaptation and can introduce unwanted rigidity by insisting on a single valid version or point of truth. In the collaborative curation domain of a research project, things are more fluid. However, there is no equivalent to the "versioning iso-surface" of the git protocol for the management and versioning of research data. At CSIRO we are developing concepts and tools for the agile management of software code and research data for virtual research environments, based on our experiences of actual data analytics projects in the

Lower lattice thermal conductivity in SbAs than As or Sb monolayers: a first-principles study.

PubMed

Guo, San-Dong; Liu, Jiang-Tao

2017-12-06

Phonon transport in group-VA element (As, Sb and Bi) monolayer semiconductors has been widely investigated in theory, and, of them, monolayer Sb (antimonene) has recently been synthesized. In this work, phonon transport in monolayer SbAs is investigated with a combination of first-principles calculations and the linearized phonon Boltzmann equation. It is found that the lattice thermal conductivity of monolayer SbAs is lower than those of both monolayer As and Sb, and the corresponding sheet thermal conductance is 28.8 W K -1 at room temperature. To understand the lower lattice thermal conductivity in monolayer SbAs than those in monolayer As and Sb, the group velocities and phonon lifetimes of monolayer As, SbAs and Sb are calculated. The calculated results show that the group velocities of monolayer SbAs are between those of monolayer As and Sb, but that the phonon lifetimes of SbAs are smaller than those of both monolayer As and Sb. Hence, the low lattice thermal conductivity in monolayer SbAs is attributed to very small phonon lifetimes. Unexpectedly, the ZA branch has very little contribution to the total thermal conductivity, only 2.4%, which is obviously different from those of monolayer As and Sb with very large contributions. This can be explained by very small phonon lifetimes for the ZA branch of monolayer SbAs. The lower lattice thermal conductivity of monolayer SbAs compared to that of monolayer As or Sb can be understood by the alloying of As (Sb) with Sb (As), which should introduce phonon point defect scattering. We also consider the isotope and size effects on the lattice thermal conductivity. It is found that isotope scattering produces a neglectful effect, and the lattice thermal conductivity with a characteristic length smaller than 30 nm can reach a decrease of about 47%. These results may offer perspectives on tuning the lattice thermal conductivity by the mixture of multiple elements for applications of thermal management and

Modal gain characteristics of a 2 μm InGaSb/AlGaAsSb passively mode-locked quantum well laser

NASA Astrophysics Data System (ADS)

Li, Xiang; Wang, Hong; Qiao, Zhongliang; Guo, Xin; Ng, Geok Ing; Zhang, Yu; Niu, Zhichuan; Tong, Cunzhu; Liu, Chongyang

2017-12-01

Passive mode locking with a fundamental repetition rate at ˜18.46 GHz is demonstrated in a two-section InGaSb/AlGaAsSb quantum well laser emitting at 2 μm. Modal gain characteristics of the laser are investigated by performing the Hakki-Paoli method to gain better insight into the impact of the absorber bias voltage (Va) on the light output. The lasing action moves to longer wavelengths markedly with increasing negative Va. The light output contains more longitudinal modes in the mode locking regime if the gain bandwidth is larger at a certain Va. Our findings provide guidelines for output characteristics of the mode-locked laser.

Adopting best practices: "Agility" moves from software development to healthcare project management.

PubMed

Kitzmiller, Rebecca; Hunt, Eleanor; Sproat, Sara Breckenridge

2006-01-01

It is time for a change in mindset in how nurses operationalize system implementations and manage projects. Computers and systems have evolved over time from unwieldy mysterious machines of the past to ubiquitous computer use in every aspect of daily lives and work sites. Yet, disconcertingly, the process used to implement these systems has not evolved. Technology implementation does not need to be a struggle. It is time to adapt traditional plan-driven implementation methods to incorporate agile techniques. Agility is a concept borrowed from software development and is presented here because it encourages flexibility, adaptation, and continuous learning as part of the implementation process. Agility values communication and harnesses change to an advantage, which facilitates the natural evolution of an adaptable implementation process. Specific examples of agility in an implementation are described, and plan-driven implementation stages are adapted to incorporate relevant agile techniques. This comparison demonstrates how an agile approach enhances traditional implementation techniques to meet the demands of today's complex healthcare environments.

Balancing Plan-Driven and Agile Methods in Software Engineering Project Courses

NASA Astrophysics Data System (ADS)

Boehm, Barry; Port, Dan; Winsor Brown, A.

2002-09-01

For the past 6 years, we have been teaching a two-semester software engineering project course. The students organize into 5-person teams and develop largely web-based electronic services projects for real USC campus clients. We have been using and evolving a method called Model- Based (System) Architecting and Software Engineering (MBASE) for use in both the course and in industrial applications. The MBASE Guidelines include a lot of documents. We teach risk-driven documentation: if it is risky to document something, and not risky to leave it out (e.g., GUI screen placements), leave it out. Even so, students tend to associate more documentation with higher grades, although our grading eventually discourages this. We are always on the lookout for ways to have students learn best practices without having to produce excessive documentation. Thus, we were very interested in analyzing the various emerging agile methods. We found that agile methods and milestone plan-driven methods are part of a “how much planning is enough?” spectrum. Both agile and plan-driven methods have home grounds of project characteristics where they clearly work best, and where the other will have difficulties. Hybrid agile/plan-driven approaches are feasible, and necessary for projects having a mix of agile and plan-driven home ground characteristics. Information technology trends are going more toward the agile methods' home ground characteristics of emergent requirements and rapid change, although there is a concurrent increase in concern with dependability. As a result, we are currently experimenting with risk-driven combinations of MBASE and agile methods, such as integrating requirements, test plans, peer reviews, and pair programming into “agile quality management.”

STM/STS Study of the Sb (111) Surface

NASA Astrophysics Data System (ADS)

Chekmazov, S. V.; Bozhko, S. I.; Smirnov, A. A.; Ionov, A. M.; Kapustin, A. A.

An Sb crystal is a Peierls insulator. Formation of double layers in the Sb structure is due to the shift of atomic planes (111) next but one along the C3 axis. Atomic layers inside the double layer are connected by covalent bonds. The interaction between double layers is determined mainly by Van der Waals forces. The cleave of an Sb single crystal used to be via break of Van der Waals bonds. However, using scanning tunneling microscopy (STM) and spectroscopy (STS) we demonstrated that apart from islands equal in thickness to the double layer, steps of one atomic layer in height also exist on the cleaved Sb (111) surface. Formation of "unpaired" (111) planes on the surface leads to a local break of conditions of Peierls transition. STS experiment reveals higher local density of states (LDOS) measured for "unpaired" (111) planes in comparison with those for the double layer.

Comparison of W-VC-C composites against Co-60, Se-75 and Sb-125 for gamma radioisotope sources

NASA Astrophysics Data System (ADS)

Demir, Ertugrul; Tugrul, A. Beril; Buyuk, Bulent; Yilmaz, Ozan; Ovecoglu, Lutfi

2018-02-01

Tungsten based materials are considered to be the promising materials for nuclear applications due to the good properties. The tungsten composite materials have so many advantages in nuclear technological applications especially fusion reactor systems. In this paper, Tungsten-Vanadium carbide-Graphite (W-VC-C) which include 93% tungsten (W), 6% vanadium carbide (VC) and 1% graphite (C) also which has three different alloying time (6-12-24 hours) were produced by mechanical alloying method. Co-60, Se-75 and Sb-125 gamma radioisotopeswere used as a gamma sources in order to determine behavior of gamma attenuation properties of the composite materials. The experimental results were compared with each other to clarify effects of varying gamma energies on the tungsten based composite materials. The mass attenuation coefficients of the samples were obtained by using XCOM computer code and compared with experimental data. The gamma linear attenuation, the mass attenuation coefficients and half value thickness (HVL) of the samples were evaluated and compared with Co-60, Se-75 and Sb-125 for gamma radioisotopes. Results showed that gamma attenuation coefficients of the samples depend on gamma energies and mechanical alloying time has negatively effect on the gamma shielding properties for the all studied W-VC-C.

Current State of Agile User-Centered Design: A Survey

NASA Astrophysics Data System (ADS)

Hussain, Zahid; Slany, Wolfgang; Holzinger, Andreas

Agile software development methods are quite popular nowadays and are being adopted at an increasing rate in the industry every year. However, these methods are still lacking usability awareness in their development lifecycle, and the integration of usability/User-Centered Design (UCD) into agile methods is not adequately addressed. This paper presents the preliminary results of a recently conducted online survey regarding the current state of the integration of agile methods and usability/UCD. A world wide response of 92 practitioners was received. The results show that the majority of practitioners perceive that the integration of agile methods with usability/UCD has added value to their adopted processes and to their teams; has resulted in the improvement of usability and quality of the product developed; and has increased the satisfaction of the end-users of the product developed. The top most used HCI techniques are low-fidelity prototyping, conceptual designs, observational studies of users, usability expert evaluations, field studies, personas, rapid iterative testing, and laboratory usability testing.

Quantifying performance on an outdoor agility drill using foot-mounted inertial measurement units.

PubMed

Zaferiou, Antonia M; Ojeda, Lauro; Cain, Stephen M; Vitali, Rachel V; Davidson, Steven P; Stirling, Leia; Perkins, Noel C

2017-01-01

Running agility is required for many sports and other physical tasks that demand rapid changes in body direction. Quantifying agility skill remains a challenge because measuring rapid changes of direction and quantifying agility skill from those measurements are difficult to do in ways that replicate real task/game play situations. The objectives of this study were to define and to measure agility performance for a (five-cone) agility drill used within a military obstacle course using data harvested from two foot-mounted inertial measurement units (IMUs). Thirty-two recreational athletes ran an agility drill while wearing two IMUs secured to the tops of their athletic shoes. The recorded acceleration and angular rates yield estimates of the trajectories, velocities and accelerations of both feet as well as an estimate of the horizontal velocity of the body mass center. Four agility performance metrics were proposed and studied including: 1) agility drill time, 2) horizontal body speed, 3) foot trajectory turning radius, and 4) tangential body acceleration. Additionally, the average horizontal ground reaction during each footfall was estimated. We hypothesized that shorter agility drill performance time would be observed with small turning radii and large tangential acceleration ranges and body speeds. Kruskal-Wallis and mean rank post-hoc statistical analyses revealed that shorter agility drill performance times were observed with smaller turning radii and larger tangential acceleration ranges and body speeds, as hypothesized. Moreover, measurements revealed the strategies that distinguish high versus low performers. Relative to low performers, high performers used sharper turns, larger changes in body speed (larger tangential acceleration ranges), and shorter duration footfalls that generated larger horizontal ground reactions during the turn phases. Overall, this study advances the use of foot-mounted IMUs to quantify agility performance in contextually

Speed and agility of 12- and 14-year-old elite male basketball players.

PubMed

Jakovljevic, Sasa T; Karalejic, Milivoje S; Pajic, Zoran B; Macura, Marija M; Erculj, Frane F

2012-09-01

The aims of this study were (a) to identify and compare the speed and agility of 12- and 14-year-old elite male basketball players and (b) to investigate relations between speed and agility for both age groups of basketball players, to help coaches to improve their work. Sixty-four players aged 12 (M = 11.98 years, SD = 0.311) and 54 players aged 14 (M = 14.092 years, SD = 0.275) were tested. Three agility tests: agility t-test, zigzag agility drill, and agility run 4 × 15 m and 3 speed tests: 20-m run, 30-m run, and 50-m run were applied. Fourteen-year-old players achieved significantly better results in all speed and agility tests compared with 12-year-old players. The correlation coefficient (r = 0.81, p = 0.001) showed that 12-year-old players have the same ability in the 30- and 50-m runs. The other correlation coefficient (r = 0.59, p = 0.001) indicated that 20- and 30-m runs had inherently different qualities. The correlation coefficients between agility tests were <0.71, and therefore, each test in this group represents a specific task. In 14-year-old players, the correlation coefficients between the speed test results were <0.71. In contrast, the correlation coefficients between the agility tests were >0.71, which means that all the 3 tests represent the same quality. During the speed training of 12-year-old players, it is advisable to focus on shorter running distances, up to 30 m. During the agility training of the same players, it is useful to apply exercises with various complexities. In speed training of the 14-year-old players, the 30- and 50-m runs should be applied, and agility training should include more specific basketball movements and activities.

Centrosymmetry vs noncentrosymmetry in La2Ga0.33SbS5 and Ce4GaSbS9 based on the interesting size effects of lanthanides: Syntheses, crystal structures, and optical properties

NASA Astrophysics Data System (ADS)

Zhao, Hua-Jun

2016-05-01

Two new quaternary sulfides La2Ga0.33SbS5 and Ce4GaSbS9 have been prepared from stoichiometric elements at 1223 K in an evacuated silica tube. Interestingly, La2Ga0.33SbS5 crystallizes in the centrosymmetric structure, while Ce4GaSbS9 crystallizes in the noncentrosymmetric structure, which show obvious size effects of lanthanides on the crystal structures of these two compounds. Ce4GaSbS9 belongs to RE4GaSbS9 (RE=Pr, Nd, Sm, Gd-Ho) structure type with a=13.8834(9) Å, b=14.3004(11) Å, c=14.4102(13) Å, V=2861.0(4) Å3. The structure features infinite chains of [Ga2Sb2S1110-]∞ propagating along a direction separated by Ce3+ cations and S2- anions. La2Ga0.33SbS5 adopts the family of La4FeSb2S10-related structure with a=7.5193(6) Å, c=13.4126(17) Å, V=758.35(13) Å3. Its structure is built up from the alternate stacking of La/Sb/S and La/Ga/S 2D building blocks. The La/Sb/S slabs consist of teeter-totter chains of Sb1S4 seesaws, which are connected via sharing the apexes of μ4-S1. Moreover, La1 is positionally disordered with Sb1 and stabilized in a bicapped trigonal prismatic coordination sphere. Between these La/Sb/S slabs, La2S8 square antiprisms are connected via edge-sharing into 2D building blocks, creating tetrahedral sites partially occupied by the Ga1 atoms. UV/Vis diffuse reflectance spectroscopy study shows that the optical gap of La2Ga0.33SbS5 is about 1.76 eV.

DoD Acquisitions Reform: Embracing and Implementing Agile

DTIC Science & Technology

2015-12-01

required in the traditional waterfall approach.   Specific models for enterprise level efforts include Scaled Agile Framework, Disciplined Agile...and Acquisition Concerns. Pittsburgh: Carnegie Mellon.  Leffingwell, D. (2007). Why The Waterfall Model Doesn’t Work. In D. Leffingwell, Scaling...serious issue might be the acquisitions process itself. For the last twenty plus years, the Air Force has used the waterfall approach for software

Microstructure and interface analysis of emerging Ga(Sb,Bi) epilayers and Ga(Sb,Bi)/GaSb quantum wells for optoelectronic applications

NASA Astrophysics Data System (ADS)

Luna, E.; Delorme, O.; Cerutti, L.; Tournié, E.; Rodriguez, J.-B.; Trampert, A.

2018-04-01

Using transmission electron microscopy, we present an in-depth microstructural analysis of a series of Ga(Sb,Bi) epilayers and Ga(Sb,Bi)/GaSb quantum wells grown on GaSb(001) substrates by molecular beam epitaxy. Despite the dilute bismide compound Ga(Sb,Bi) is regarded as a highly-mismatched alloy, we find that the material is of remarkable structural perfection, even up to 11%-14% Bi, the maximum Bi concentration incorporated into GaSb so far. No extended defects, nanoclusters, or composition modulations are detectable in the pseudomorphic layers. In addition, the quantum wells exhibit regular and homogeneous morphologies including smooth and stable interfaces with a chemical width on the same order as in other high-quality III-V heterointerfaces. These results may give reasons for the recent successful realization of mid-infrared lasers with room temperature operation based on the very same quantum well structures.

Agile manufacturing: The factory of the future

NASA Technical Reports Server (NTRS)

Loibl, Joseph M.; Bossieux, Terry A.

1994-01-01

The factory of the future will require an operating methodology which effectively utilizes all of the elements of product design, manufacturing and delivery. The process must respond rapidly to changes in product demand, product mix, design changes or changes in the raw materials. To achieve agility in a manufacturing operation, the design and development of the manufacturing processes must focus on customer satisfaction. Achieving greatest results requires that the manufacturing process be considered from product concept through sales. This provides the best opportunity to build a quality product for the customer at a reasonable rate. The primary elements of a manufacturing system include people, equipment, materials, methods and the environment. The most significant and most agile element in any process is the human resource. Only with a highly trained, knowledgeable work force can the proper methods be applied to efficiently process materials with machinery which is predictable, reliable and flexible. This paper discusses the affect of each element on the development of agile manufacturing systems.

Removal of antimony (Sb(V)) from Sb mine drainage: biological sulfate reduction and sulfide oxidation-precipitation.

PubMed

Wang, Huawei; Chen, Fulong; Mu, Shuyong; Zhang, Daoyong; Pan, Xiangliang; Lee, Duu-Jong; Chang, Jo-Shu

2013-10-01

Antimony (Sb(V)) in Sb mine drainage has adverse effects on the receiving water environments. This study for the first time demonstrated the feasibility of using sulfate-reducing bacteria (SRB) to convert sulfate ions in SMD into sulfides that reduce Sb(V) to Sb(III) and to form complex with Sb(III) as precipitate. The principal compound in the precipitate was stibnite (Sb2S3) at pH 7 and pH 9. The Sb(V) removal mechanism is sulfate-reduction and sulfide oxidization-precipitation, different from the conventional SRB-precipitation processes for heavy metals. The Sb(V)/sulfate ratio is noted an essential parameter affecting the Sb removal efficiency from SMD. Copyright © 2013 Elsevier Ltd. All rights reserved.

[Direct determination of purine bases in tea by reversed-phase high performance liquid chromatography].

PubMed

Ding, M; Yang, H; Xiao, S; Chen, P

1999-09-01

A reversed-phase high performance liquid chromatographic(RP-HPLC) method for the direct determination of three purine bases(theobromin, theophyllin and caffeine) in tea was developed. An ODS column with Zorbax SB-C18(4.6 mm i.d. x 250 mm, 5 microns) was employed. The aqueous solution of methanol containing 0.05% of acetic acid and 0.25% of N,N-dimethylformamide(DMF) was used as eluent with a flow rate of 0.8 mL/min. In this method, the aqueous extract of tea can be injected into HPLC directly, but in current HPLC methods for purine bases the coexisted tea polyphenols must be pre-separated. The three purine bases in tea were separated without any interference from the coexisted tea polyphenols. This method is simple (without any special sample pretreatment) and sensitive with detection limits (S/N = 3) of 0.7, 0.9 and 1.8 mg/L for theobromin, theophyllin and caffeine respectively. The linear range of the calibration curve of peak area for the three purine bases were from 6 mg/L to 1,000 mg/L with a correlation coefficient (r) of 0.998-0.999.

A Roadmap for using Agile Development in a Traditional System

NASA Technical Reports Server (NTRS)

Streiffert, Barbara; Starbird, Thomas

2006-01-01

I. Ensemble Development Group: a) Produces activity planning software for in spacecraft; b) Built on Eclipse Rich Client Platform (open source development and runtime software); c) Funded by multiple sources including the Mars Technology Program; d) Incorporated the use of Agile Development. II. Next Generation Uplink Planning System: a) Researches the Activity Planning and Sequencing Subsystem for Mars Science Laboratory (APSS); b) APSS includes Ensemble, Activity Modeling, Constraint Checking, Command Editing and Sequencing tools plus other uplink generation utilities; c) Funded by the Mars Technology Program; d) Integrates all of the tools for APSS.

In-situ characterization of the optical and electronic properties in GeTe and GaSb thin films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Velea, A.; Popescu, M.; Galca, A. C., E-mail: ac-galca@infim.ro

2015-10-07

GeTe and GaSb thin films obtained by pulsed laser deposition were investigated by spectroscopic ellipsometry at controlled temperatures. The GeTe films were fully amorphous, while the GaSb films were partially crystalized in the as-deposited state. The Tauc-Lorentz model was employed to fit the experimental data. From the temperature study of the optical constants, it was observed the crystallization in the 150–160 °C range of GeTe amorphous films and between 230 and 240 °C of GaSb amorphous phase. A second transition in the resonance energy and the broadening parameter of the Lorentz oscillator was observed due to the crystallization of Sb after 250 °C.more » The temperatures of 85 °C and 130 °C are noticed as the start of the relaxation of the amorphous GeTe phase and as-deposited GaSb. The peaks of the imaginary part of the dielectric function red shifted after the phase change, while the variation with temperature of the crystalline phase follows the Varshni law. The electron-phonon coupling constants are 2.88 and 1.64 for c-GeTe and c-GaSb, respectively. An optical contrast up to 60% was obtained for GeTe films and a maximum value of 7.5% is revealed in the case GaSb, which is altered by the partial crystallinity of the as-deposited films.« less

Strategy quantification using body worn inertial sensors in a reactive agility task.

PubMed

Eke, Chika U; Cain, Stephen M; Stirling, Leia A

2017-11-07

Agility performance is often evaluated using time-based metrics, which provide little information about which factors aid or limit success. The objective of this study was to better understand agility strategy by identifying biomechanical metrics that were sensitive to performance speed, which were calculated with data from an array of body-worn inertial sensors. Five metrics were defined (normalized number of foot contacts, stride length variance, arm swing variance, mean normalized stride frequency, and number of body rotations) that corresponded to agility terms defined by experts working in athletic, clinical, and military environments. Eighteen participants donned 13 sensors to complete a reactive agility task, which involved navigating a set of cones in response to a vocal cue. Participants were grouped into fast, medium, and slow performance based on their completion time. Participants in the fast group had the smallest number of foot contacts (normalizing by height), highest stride length variance (normalizing by height), highest forearm angular velocity variance, and highest stride frequency (normalizing by height). The number of body rotations was not sensitive to speed and may have been determined by hand and foot dominance while completing the agility task. The results of this study have the potential to inform the development of a composite agility score constructed from the list of significant metrics. By quantifying the agility terms previously defined by expert evaluators through an agility score, this study can assist in strategy development for training and rehabilitation across athletic, clinical, and military domains. Copyright © 2017 Elsevier Ltd. All rights reserved.

Multiwavelength studies of the blazars detected by AGILE

NASA Astrophysics Data System (ADS)

Filippo D'Ammando

2010-02-01

The discovery of emission in the gamma-ray domain from many Active Galactic Nuclei (AGNs) by EGRET on board the Compton Gamma-Ray Observatory and the Cherenkov Telescopes was one of the most breakthrough of high energy astrophysics in the last 20 years, leading to the identification of a new class of AGNs: the blazars. Blazars are the most extreme subclass of AGNs, characterized by the emission of strong non-thermal radiation across the entire electromagnetic spectrum, from radio to very high gamma-ray energies. This emission is interpreted as the result of the electromagnetic radiation from a relativistic jet that is viewed closely aligned to the line of sight of the observer, thus causing strong relativistic amplification. Considering that the large fraction of the total power of blazars is emitted in the gamma-rays, information in this energy band is crucial to study the different radiation models. More than ten years after the EGRET era, the AGILE satellite (and subsequently also the Fermi satellite) filled the gap in the MeV-GeV band giving further impulse to the study of the high-energy astrophysics phenomena in blazars. However, notwithstanding the importance of the information provided by the gamma-ray observations, correlated multiwavelength studies are the key to achieve a better understanding of the structure of the inner jet, the origin of the seed photons for the inverse Compton process and the emission mechanisms at work in blazars. Since its launch in April 2007, the AGILE satellite detected several blazars in high activity state: PKS 1510-089, S5 0716+714, 3C 454.3, 3C 273, 3C 279, W Comae, Mrk 421 and PG 1553+113. In this Thesis I will present the most interesting results on multifrequency analysis of these sources detected by AGILE in gamma-rays, together with the multiwavelength data from other observatories such as Spitzer, Swift, RXTE, Suzaku, INTEGRAL, MAGIC, VERITAS, as well as radio-to-optical coverage by means of GASP-WEBT and REM. This

Tailoring Agility: Promiscuous Pair Story Authoring and Value Calculation

NASA Astrophysics Data System (ADS)

Tendon, Steve

This chapter describes how a multi-national software organization created a business plan involving business units from eight countries that followed an agile way, after two previously failed attempts with traditional approaches. The case is told by the consultant who initiated implementation of agility into requirements gathering, estimation and planning processes in an international setting. The agile approach was inspired by XP, but then tailored to meet the peculiar requirements. Two innovations were critical. The first innovation was promiscuous pair story authoring, where user stories were written by two people (similarly to pair programming), and the pairing changed very often (as frequently as every 15-20 minutes) to achieve promiscuity and cater for diverse point of views. The second innovation was an economic value evaluation (and not the cost) which was attributed to stories. Continuous recalculation of the financial value of the stories allowed to assess the projects financial return. In this case implementation of agility in the international context allowed the involved team members to reach consensus and unanimity of decisions, vision and purpose.

Pathways to agility in the production of neutron generators

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stoltz, R.E.; Beavis, L.C.; Cutchen, J.T.

1994-02-01

This report is the result of a study team commissioned to explore pathways for increased agility in the manufacture of neutron generators. As a part of Sandia`s new responsibility for generator production, the goal of the study was to identify opportunities to reduce costs and increase flexibility in the manufacturing operation. Four parallel approaches (or pathways) were recommended: (1) Know the goal, (2) Use design leverage effectively, (3) Value simplicity, and (4) Configure for flexibility. Agility in neutron generator production can be enhanced if all of these pathways are followed. The key role of the workforce in achieving agility wasmore » also noted, with emphasis on ownership, continuous learning, and a supportive environment.« less

Mechanical Analysis of the Acute Effects of a Heavy Resistance Exercise Warm-Up on Agility Performance in Court-Sport Athletes

PubMed Central

Sole, Christopher J.; Moir, Gavin L.; Davis, Shala E.; Witmer, Chad A.

2013-01-01

The purpose of this study was to determine the acute effects of heavy resistance exercise on agility performance in court-sport athletes. Five men (age: 20.6 ± 1.9 years; body mass: 79.36 ± 11.74 kg; body height: 1.93 ± 0.09 m) and five women (age 21.2 ± 2.7 years; body mass: 65.8 ± 10.18 kg; body height 1.77 ± 0.08 m) volunteered to participate in the present study. All subjects were NCAA Division II athletes who currently participated in tennis or basketball and all had previous resistance training experience of at least one year. In a counterbalanced design, agility performance during a 10 m shuttle test was assessed following either a dynamic warm-up (DW) or heavy resistance warm-up (HRW) protocol. The HRW protocol consisted of three sets of squats at 50, 60, and 90% of 1-RM. Agility performance was captured using an eight camera motion analysis system and the mechanical variables of stride length, stride frequency, stance time, flight time, average ground reaction force, as well as agility time were recorded. No significant differences were reported for the HRW and DW protocols for any of the mechanical variables (p>0.05), although there was a trend towards the HRW protocol producing faster agility times compared to the control protocol (p = 0.074). Based on the trend towards a significant effect, as well as individual results it is possible that HRW protocols could be used as an acute method to improve agility performance in some court-sport athletes. PMID:24511350

Wavelength-Agile External-Cavity Diode Laser for DWDM

NASA Technical Reports Server (NTRS)

Pilgrim, Jeffrey S.; Bomse, David S.

2006-01-01

A prototype external-cavity diode laser (ECDL) has been developed for communication systems utilizing dense wavelength- division multiplexing (DWDM). This ECDL is an updated version of the ECDL reported in Wavelength-Agile External- Cavity Diode Laser (LEW-17090), NASA Tech Briefs, Vol. 25, No. 11 (November 2001), page 14a. To recapitulate: The wavelength-agile ECDL combines the stability of an external-cavity laser with the wavelength agility of a diode laser. Wavelength is modulated by modulating the injection current of the diode-laser gain element. The external cavity is a Littman-Metcalf resonator, in which the zeroth-order output from a diffraction grating is used as the laser output and the first-order-diffracted light is retro-reflected by a cavity feedback mirror, which establishes one end of the resonator. The other end of the resonator is the output surface of a Fabry-Perot resonator that constitutes the diode-laser gain element. Wavelength is selected by choosing the angle of the diffracted return beam, as determined by position of the feedback mirror. The present wavelength-agile ECDL is distinguished by design details that enable coverage of all 60 channels, separated by 100-GHz frequency intervals, that are specified in DWDM standards.

Investigation into the impact of agility on conceptual fighter design

NASA Technical Reports Server (NTRS)

Engelbeck, R. M.

1995-01-01

The Agility Design Study was performed by the Boeing Defense and Space Group for the NASA Langley Research Center. The objective of the study was to assess the impact of agility requirements on new fighter configurations. Global trade issues investigated were the level of agility, the mission role of the aircraft (air-to-ground, multi-role, or air-to-air), and whether the customer is Air force, Navy, or joint service. Mission profiles and design objectives were supplied by NASA. An extensive technology assessment was conducted to establish the available technologies to industry for the aircraft. Conceptual level methodology is presented to assess the five NASA-supplied agility metrics. Twelve configurations were developed to address the global trade issues. Three-view drawings, inboard profiles, and performance estimates were made and are included in the report. A critical assessment and lessons learned from the study are also presented.

Method of making AlInSb by metal-organic chemical vapor deposition

DOEpatents

Biefeld, Robert M.; Allerman, Andrew A.; Baucom, Kevin C.

2000-01-01

A method for producing aluminum-indium-antimony materials by metal-organic chemical vapor deposition (MOCVD). This invention provides a method of producing Al.sub.X In.sub.1-x Sb crystalline materials by MOCVD wherein an Al source material, an In source material and an Sb source material are supplied as a gas to a heated substrate in a chamber, said Al source material, In source material, and Sb source material decomposing at least partially below 525.degree. C. to produce Al.sub.x In.sub.1-x Sb crystalline materials wherein x is greater than 0.002 and less than one.

Transport properties of Sb doped Si nanowires

NASA Astrophysics Data System (ADS)

Nukala, Prathyusha; Sapkota, Gopal; Gali, Pradeep; Usha, Philipose

2011-10-01

n-type Si nanowires were synthesized at ambient pressure using SiCl4 as Si source and Sb source as the dopant. Sb doping of 3-4 wt % was achieved through a post growth diffusion technique. The nanowires were found to have an amorphous oxide shell that developed post-growth; the thickness of the shell is estimated to be about 3-4 nm. The composition of the amorphous shell covering the crystalline Si core was determined by Raman spectroscopy, with evidence that the shell was an amorphous oxide layer. Optical characterization of the as-grown nanowires showed green emission, attributed to the presence of the oxide shell covering the Si nanowire core. Etching of the oxide shell was found to decrease the intensity of this green emission. A single undoped Si nanowire contacted in an FET type configuration was found to be p-type with channel mobility of 20 cm^2V-1S-1. Sb doped Si nanowires exhibited n-type behavior, compensating for the holes in the undoped nanowire. The doped nanowires had carrier mobility and concentration of 160 cm^2V-1S-1 and 9.6 x 10^18cm-3 respectively.

2.4 Micron Cutoff AlGaAsSb/InGaAsSb Phototransistors for Shortwave IR Applications

NASA Technical Reports Server (NTRS)

Refaat, Tamer F.; Abedin, Nurul; Sulima, Oleg V.; Swaminathan, Krishna; Ismail, Syed; Singh, Upendra N.

2006-01-01

Shortwave infrared detectors are critical for several applications including remote sensing and optical communications. Several detectors are commercially available for this wavelength range, but they lack sufficient gain, which limits their detectivity. The characterization results of an AlGaAsSb/InGaAsSb phototransistor for shortwave IR application are reported. The phototransistor is grown using molecular beam epitaxy technique. Spectral response measurements showed a uniform responsivity between 1.2 and 2.4 micron region with a mean value of 1000 A/W. A maximum detectivity of 3.4 X 10(exp 11) cmHz1/2/W was obtained at 2 micron at -20 C and 1.3 V.

Effect of InSb/In0.9Al0.1Sb superlattice buffer layer on the structural and electronic properties of InSb films

NASA Astrophysics Data System (ADS)

Zhao, Xiaomeng; Zhang, Yang; Guan, Min; Cui, Lijie; Wang, Baoqiang; Zhu, Zhanping; Zeng, Yiping

2017-07-01

The effect of InSb/In0.9Al0.1Sb buffer layers on InSb thin films grown on GaAs (0 0 1) substrate by molecular beam epitaxy (MBE) is investigated. The crystal quality and the surface morphology of InSb are characterized by XRD and AFM. The carrier transport property is researched through variable temperature hall test. The sharp interface between InSb/In0.9Al0.1Sb is demonstrated important for the high quality InSb thin film. We try different superlattice buffer layers by changing ratios, 2-0.5, thickness, 300-450 nm, and periods, 20-50. According to the function of the dislocation density to the absolute temperature below 150 K with different periods of SL buffers, we can find that the number of periods of superlattice is a major factor to decrease the density of threading dislocations. With the 50 periods SL buffer layer, the electron mobility of InSb at the room temperature and liquid nitrogen cooling temperature is ∼63,000 and ∼4600 cm2/V s, respectively. We deduce that the interface in the SL structure works as a filter layer to prevent the dislocation propagating to the upper InSb thin films.

LC/MS Method for the Determination of Stable Isotope Labeled Promethazine in Human Plasma

NASA Technical Reports Server (NTRS)

Zuwei, Wang; Boyd, Jason; Berens, Kurt L.; Putcha, Lakshmi

2004-01-01

Promethazine (PMZ) is taken by astronauts orally (PO), intramuscularly (IM) or rectally (PR) for space motion sickness. LC/MS method was developed with off-line solid phase extraction to measure plasma concentrations of PMZ given as stable isotope-labeled (SIL) formulations by the three different routes of administration simultaneously. Samples (0.5ml) were loaded on to Waters Oasis HLB co-polymer cartridges and eluted with 1.0 mL methanol. HPLC separation of the eluted sample was performed using an Agilent Zorbax SB-CN column (50 x 2.1 mm) at a flow rate of 0.2 mL/min for 6 min. Acetonitrile/ ammonium acetate (30 mM) in water (3:2, v/v), pH 5.6 plus or minus 0.1, was used as the mobile phase for separation. Concentrations of PMZ, PMZ-d4 and PMZ-d7 and chlorpromazine (internal standard) were determined using a Micromass ZMD single quadrupole mass spectrometer with Electrospray Ionization (ESI). ESI mass spectra were acquired in positive ion mode with selected ion monitoring of [M+ H]dot plus. The method is rapid, reproducible and the assay specific parameters are listed in a table. A novel, sensitive and specific method for the measurement of PMZ and SIL PMZ in human plasma is reported.

Electric measurement and magnetic control of spin transport in InSb-based lateral spin devices

NASA Astrophysics Data System (ADS)

Viglin, N. A.; Ustinov, V. V.; Demokritov, S. O.; Shorikov, A. O.; Bebenin, N. G.; Tsvelikhovskaya, V. M.; Pavlov, T. N.; Patrakov, E. I.

2017-12-01

Electric injection and detection of spin-polarized electrons in InSb semiconductors have been realized in nonlocal experimental geometry using an InSb-based "lateral spin valve." The valve of the InSb /MgO /C o0.9F e0.1 composition has semiconductor/insulator/ferromagnet nanoheterojunctions in which the thickness of the InSb layer considerably exceeded the spin diffusion length of conduction electrons. The spin direction in spin diffusion current has been manipulated by a magnetic field under the Hanle effect conditions. The spin polarization of the electron gas has been registered using ferromagnetic C o0.9F e0.1 probes by measuring electrical potentials arising in the probes in accordance with the Johnson-Silsbee concept of the spin-charge coupling. The developed theory is valid at any degree of degeneracy of electron gas in a semiconductor. The spin relaxation time and spin diffusion length of conduction electrons in InSb have been determined, and the electron-spin polarization in InSb has been evaluated for electrons injected from C o0.9F e0.1 through an MgO tunnel barrier.

Strain-Balanced InAs/InAs1-xSbx Type-II Superlattices Grown by Molecular Beam Epitaxy on GaSb Substrates

DTIC Science & Technology

2011-12-21

C. Four samples A, B, C, and D with 20 period SLs were grown under identical condi- tions with varying Sb/(Asþ Sb) beam equivalent pressure ( BEP ) flux...incorporation can be achieved. Thus, the InAs1xSbx layers in samples A, B, C, and D have Sb/(AsþSb) BEP ratios of 0.32, 0.347, 0.378, and 0.412

Moving target detection for frequency agility radar by sparse reconstruction

NASA Astrophysics Data System (ADS)

Quan, Yinghui; Li, YaChao; Wu, Yaojun; Ran, Lei; Xing, Mengdao; Liu, Mengqi

2016-09-01

Frequency agility radar, with randomly varied carrier frequency from pulse to pulse, exhibits superior performance compared to the conventional fixed carrier frequency pulse-Doppler radar against the electromagnetic interference. A novel moving target detection (MTD) method is proposed for the estimation of the target's velocity of frequency agility radar based on pulses within a coherent processing interval by using sparse reconstruction. Hardware implementation of orthogonal matching pursuit algorithm is executed on Xilinx Virtex-7 Field Programmable Gata Array (FPGA) to perform sparse optimization. Finally, a series of experiments are performed to evaluate the performance of proposed MTD method for frequency agility radar systems.

Moving target detection for frequency agility radar by sparse reconstruction.

PubMed

Quan, Yinghui; Li, YaChao; Wu, Yaojun; Ran, Lei; Xing, Mengdao; Liu, Mengqi

2016-09-01

Frequency agility radar, with randomly varied carrier frequency from pulse to pulse, exhibits superior performance compared to the conventional fixed carrier frequency pulse-Doppler radar against the electromagnetic interference. A novel moving target detection (MTD) method is proposed for the estimation of the target's velocity of frequency agility radar based on pulses within a coherent processing interval by using sparse reconstruction. Hardware implementation of orthogonal matching pursuit algorithm is executed on Xilinx Virtex-7 Field Programmable Gata Array (FPGA) to perform sparse optimization. Finally, a series of experiments are performed to evaluate the performance of proposed MTD method for frequency agility radar systems.

GaSbBi/GaSb quantum-well and wire laser diodes

NASA Astrophysics Data System (ADS)

Ridene, Said

2018-06-01

In this work, we present detailed theoretical studies of the optical gain spectra and the emission wavelength of GaSb1-xBix/GaSb and traditional GaAs1-xBix/GaAs dilute-bismide quantum wells and wires (QWs, QWRs) focusing on comparison between their performances. It is found that the optical gain and the emission wavelength of the GaSb-based QW and QWRs lasers would be considerably greater than that of the GaAs-based QW lasers and QWRs for the same QW-, QWR-width, Bi-content and carrier density. The theoretical results were found to be in good agreement with available experimental data, especially for the emission wavelength given by GaSb-based QW laser diodes.

Fully epitaxial C1b-type NiMnSb half-Heusler alloy films for current-perpendicular-to-plane giant magnetoresistance devices with a Ag spacer

PubMed Central

Wen, Zhenchao; Kubota, Takahide; Yamamoto, Tatsuya; Takanashi, Koki

2015-01-01

Remarkable magnetic and spin-dependent transport properties arise from well-designed spintronic materials and heterostructures. Half-metallic Heusler alloys with high spin polarization exhibit properties that are particularly advantageous for the development of high-performance spintronic devices. Here, we report fully (001)-epitaxial growth of a high-quality half-metallic NiMnSb half-Heusler alloy films, and their application to current-perpendicular-to-plane giant magnetoresistance (CPP-GMR) devices with Ag spacer layers. Fully (001)-oriented NiMnSb epitaxial films with very flat surface and high magnetization were prepared on Cr/Ag-buffered MgO(001) single crystalline substrates by changing the substrate temperature. Epitaxial CPP-GMR devices using the NiMnSb films and a Ag spacer were fabricated, and room-temperature (RT) CPP-GMR ratios for the C1b-type half-Heusler alloy were determined for the first time. A CPP-GMR ratio of 8% (21%) at RT (4.2 K) was achieved in the fully epitaxial NiMnSb/Ag/NiMnSb structures. Furthermore, negative anisotropic magnetoresistance (AMR) ratio and small discrepancy of the AMR amplitudes between RT and 10 K were observed in a single epitaxial NiMnSb film, indicating robust bulk half metallicity against thermal fluctuation in the half-Heusler compound. The modest CPP-GMR ratios could be attributed to interface effects between NiMnSb and Ag. This work provides a pathway for engineering a new class of ordered alloy materials with particular emphasis on spintronics. PMID:26672482

Solid Liquid Interdiffusion Bonding of Zn4Sb3 Thermoelectric Material with Cu Electrode

NASA Astrophysics Data System (ADS)

Lin, Y. C.; Lee, K. T.; Hwang, J. D.; Chu, H. S.; Hsu, C. C.; Chen, S. C.; Chuang, T. H.

2016-10-01

The ZnSb intermetallic compound may have thermoelectric applications because it is low in cost and environmentally friendly. In this study, a Zn4Sb3 thermoelectric element coated with a Ni barrier layer and a Ag reaction layer was bonded with a Ag-coated Cu electrode using a Ag/Sn/Ag solid-liquid interdiffusion bonding process. The results indicated that a Ni5Zn21 intermetallic phase formed easily at the Zn4Sb3/Ni interface, leading to sound adhesion. In addition, Sn film was found to react completely with the Ag layer to form a Ag3Sn intermetallic layer having a melting point of 480°C. The resulting Zn4Sb3 thermoelectric module can be applied at the optimized operation temperature (400°C) of Zn4Sb3 material as a thermoelectric element. The bonding strengths ranged from 14.9 MPa to 25.0 MPa, and shear tests revealed that the Zn4Sb3/Cu-joints fractured through the interior of the thermoelectric elements.

Structural and Optical Characteristics of Metamorphic Bulk InAsSb

DTIC Science & Technology

2014-01-01

0.815 0.820 0.825 InAsSb 5 /a ⊥ ( Å ) 3√2/a|| (Å) 0.25 0.40 0.75 1.3 1.5 1.8 2.2 hkl = 335 GaSb Structural and Optical Characteristics of Metamorphic...Conduction- and Valence- Band Energies in Bulk InAs1−xSbx and Type II InAs1−xSbx/InAs Strained-Layer Superlattices”, J. of Electron. Mater., 42, 918...0188 3. DATES COVERED (From - To) - UU UU UU UU Approved for public release; distribution is unlimited. Structural and Optical Characteristics of

New Antimony Lanthanide Disulfide Dibromides LnSbS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gout, D.; Jobic, S.; Evain, M.

2001-05-01

CeSbS{sub 2}Br{sub 2} (I), Ce{sub 1/2}La{sub 1/2}SbS{sub 2}Br{sub 2} (II), and LaSbS{sub 2}Br{sub 2} (III) have been synthesized at 700 C from a mixture of LnBr{sub 3}, Ln{sub 2}S{sub 3}, Sb, and S and characterized by single-crystal X-ray diffraction. The three phases are isostructural (space group P2{sub 1}/c, Z=4) and crystallize in a novel, dense, bidimensional structure with cell parameters a=8.709(3) {angstrom}, b=9.187(2) {angstrom}, c=17.397(5) {angstrom} {beta}=104.26(3) for I, a=8.739(7) {angstrom}, b=9.219(7) {angstrom}, c=17.41(2) {angstrom}, =104.3(1) for II, and a=8.785(1) {angstrom}, b=9.236(2) {angstrom}, c=17.372(3) {angstrom}, {beta}=104.09(2) for III. In these compounds, [Ln S{sub 5}Br{sub 4}] and [Ln S{sub 3}Br{sub 6}]more » (Ln=Ce, La) distorted tricapped trigonal prisms define infinite {sub {infinity}}{sup 2}[LnS{sub 2}Br{sub 2}] layers counterbalanced and capped by antimony cations. In good accordance with the structural features, the charge balance in these materials is to be written Ln{sup III}Sb{sup III}S{sup -II}{sub 2}Br{sup -I}{sub 2}. These compounds exhibit a yellow hue with a measured absorption threshold of 2.42(1), 2.55(1), and 2.72(1) eV for I, II, and III, respectively. In the two cerium containing bromothioantimonates I and II, the origin of the color is assigned to a Ce-4f{yields}Ce-5d electronic transition, which shifts to higher energy from I to II due either to a matrix effect (increase of the mean Ln-S distances under the substitution of Ce for La) or to an atomic ordering between Ce and La cations on the Ln(1) and Ln(2) crystallographic sites. In contrast, the electronic transition at play in III involves a charge transfer from the bromine and sulfur ions to the antimony ions, the latter contributing substantially to the lowermost levels of the conduction band.« less

Fermi Level Unpinning of GaSb (100) using Plasma Enhanced Atomic Layer Deposition of Al2O3

DTIC Science & Technology

2010-01-01

of high-/GaSb semiconductor interface. GaSb has a highly reactive surface and on exposure to air it will form a native oxide layer composed of Ga2O3 ...and Sb2O3 2GaSb+3O2→ Ga2O3 +Sb2O3. The Sb2O3 can fur- ther react with the GaSb surface forming elemental Sb and Ga2O3 Sb2O3+2GaSb→ Ga2O3 +4Sb.5,6...rights_and_permissions mentioned before, Sb2O3 reacts with GaSb forming Ga2O3 and elemental Sb.6 The kinetics of this reaction is enhanced at higher temperatures200 °C.14

Superconductivity in strong spin orbital coupling compound Sb 2Se 3

DOE PAGES

Kong, P. P.; Sun, F.; Xing, L. Y.; ...

2014-10-20

Recently, A 2B 3 type strong spin orbital coupling compounds such as Bi 2Te 3, Bi 2Se 3 and Sb 2Te 3 were theoretically predicated to be topological insulators and demonstrated through experimental efforts. The counterpart compound Sb 2Se 3 on the other hand was found to be topological trivial, but theoretical studies indicated that the pressure might induce Sb 2Se 3 into a topological nontrivial state. We report on the discovery of superconductivity in Sb 2Se 3 single crystal induced via pressure. Our experiments indicated that Sb 2Se 3 became superconductive at high pressures above 10 GPa proceeded bymore » a pressure induced insulator to metal like transition at ~3 GPa which should be related to the topological quantum transition. The superconducting transition temperature (T C) increased to around 8.0 K with pressure up to 40 GPa while it keeps ambient structure. As a result, high pressure Raman revealed that new modes appeared around 10 GPa and 20 GPa, respectively, which correspond to occurrence of superconductivity and to the change of T C slop as the function of high pressure in conjunction with the evolutions of structural parameters at high pressures.« less

The influence of physical and cognitive factors on reactive agility performance in men basketball players.

PubMed

Scanlan, Aaron; Humphries, Brendan; Tucker, Patrick S; Dalbo, Vincent

2014-01-01

This study explored the influence of physical and cognitive measures on reactive agility performance in basketball players. Twelve men basketball players performed multiple sprint, Change of Direction Speed Test, and Reactive Agility Test trials. Pearson's correlation analyses were used to determine relationships between the predictor variables (stature, mass, body composition, 5-m, 10-m and 20-m sprint times, peak speed, closed-skill agility time, response time and decision-making time) and reactive agility time (response variable). Simple and stepwise regression analyses determined the individual influence of each predictor variable and the best predictor model for reactive agility time. Morphological (r = -0.45 to 0.19), sprint (r = -0.40 to 0.41) and change-of-direction speed measures (r = 0.43) had small to moderate correlations with reactive agility time. Response time (r = 0.76, P = 0.004) and decision-making time (r = 0.58, P = 0.049) had large to very large relationships with reactive agility time. Response time was identified as the sole predictor variable for reactive agility time in the stepwise model (R(2) = 0.58, P = 0.004). In conclusion, cognitive measures had the greatest influence on reactive agility performance in men basketball players. These findings suggest reaction and decision-making drills should be incorporated in basketball training programmes.

Gamma-ray blazars: the combined AGILE and MAGIC views

NASA Astrophysics Data System (ADS)

Persic, M.; De Angelis, A.; Longo, F.; Tavani, M.

The large FOV of the AGILE Gamma-Ray Imaging Detector (GRID), 2.5 sr, will allow the whole sky to be surveyed once every 10 days in the 30 MeV - 50 GeV energy band down to 0.05 Crab Units. This fact gives the opportunity of performing the first flux-limited, high-energy g-ray all-sky survey. The high Galactic latitude point-source population is expected to be largely dominated by blazars. Several tens of blazars are expected to be detected by AGILE (e.g., Costamante & Ghisellini 2002), about half of which accessible to the ground-based MAGIC Cherenkov telescope. The latter can then carry out pointed observations of this subset of AGILE sources in the 50GeV - 10TeV band. Given the comparable sensitivities of AGILE/GRID and MAGIC in adjacent energy bands where the emitted radiation is produced by the same (e.g., SSC) mechanism, we expect that most of these sources can be detected by MAGIC. We expect this broadband g-ray strategy to enable discovery by MAGIC of 10-15 previously unknown TeV blazars.

Network configuration management : paving the way to network agility.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maestas, Joseph H.

2007-08-01

Sandia networks consist of nearly nine hundred routers and switches and nearly one million lines of command code, and each line ideally contributes to the capabilities of the network to convey information from one location to another. Sandia's Cyber Infrastructure Development and Deployment organizations recognize that it is therefore essential to standardize network configurations and enforce conformance to industry best business practices and documented internal configuration standards to provide a network that is agile, adaptable, and highly available. This is especially important in times of constrained budgets as members of the workforce are called upon to improve efficiency, effectiveness, andmore » customer focus. Best business practices recommend using the standardized configurations in the enforcement process so that when root cause analysis results in recommended configuration changes, subsequent configuration auditing will improve compliance to the standard. Ultimately, this minimizes mean time to repair, maintains the network security posture, improves network availability, and enables efficient transition to new technologies. Network standardization brings improved network agility, which in turn enables enterprise agility, because the network touches all facets of corporate business. Improved network agility improves the business enterprise as a whole.« less

Experimental and theoretical investigation of topological and energetic characteristics of Sb complexes reversibly binding molecular oxygen.

PubMed

Fukin, Georgy K; Baranov, Evgenii V; Jelsch, Christian; Guillot, Benoît; Poddel'sky, Andrey I; Cherkasov, Vladimir K; Abakumov, Gleb A

2011-07-28

The experimental distribution of electron density in Ph(3)(4,5-OMe-3,6-Bu(t)-Cat)Sb·MeCN (1*) and Ph(3)(4,5-N(2)C(4)H(6)-3,6-Bu(t)-Cat)Sb·MeOH (2*) complexes was studied. According to atoms in molecules theory, the Sb-C(Ph), Sb-O(catecholate), and Sb···N(O) bonds are intermediate, whereas the O-C and C-C bonds are covalent, respectively. The energy of the Sb···N(MeCN) and Sb···O(MeOH) bonds are 7.0 and 11.3 kcal/mol according to the Espinosa equation. Density functional theory and Hartree-Fock calculations were carried out for a series of catecholate and amidophenolate complexes of antimony(V). It was shown that such calculations reliably reproduce geometrical and topological parameters and therefore can be used for a criterion search of dioxygen reversible binding by the catecholate and amidophenolate complexes of antimony(V). It was found that the "critical" value of the HOMO energy vary in the range from -5.197 to -5.061 eV for reversible binding of dioxygen complexes. This can serve as a thermodynamic criterion to predict the possibility of the dioxygen reversible binding by the catecholate and amidophenolate complexes of Sb(V). The HOMO energies correlate with the conversion of the catecholate and amidophenolate complexes in corresponding spiroendoperoxide derivatives as well. The contribution of the atom orbitals of the carbon atoms in the five-membered metallocycle to HOMO in complexes with different substitutes in the 4- and 5-positions of the catecholate ligand allows predicting the place of dioxygen addition. © 2011 American Chemical Society

[Application of fingerprint chromatogram in quality assessment of apple cider].

PubMed

Xu, Kangzhen; Song, Jirong; Ren, Yinghui; Ma, Haixia; Huang, Jie; Du, Xiaodan

2007-01-01

Fingerprints of 14 apple cider samples from different manufacturers were studied using high performance liquid chromatography (HPLC) with an electrochemical detector (ECD). The analysis was carried out on a Zorbax SB-C18 column at 30 degrees C with 2% (v/v) methanol aqueous solution-4% (v/v) acetic acid aqueous solution as mobile phase at a flow rate of 0.8 mL/min. The electrochemical detector was set at 0.7 V. By calculating the relative retention times of certain peaks with chlorogenic acid as the reference standard, 8 common peaks in the samples were analyzed. Relative retention times for the common peaks of various samples were calculated, and the similarities of all the samples were figured out through each peak area with the vectorial angle cosine method and correlative coefficient method. The results indicated that apple cider products of the same manufacturer have good similarity, with the similarities greater than 92.7%. According to this experiment, effectual microcosmic information for apple cider analysis was gained through HPLC and ECD. Moreover, this test method will help the analysis and the control of product quality, the development of new products and the establishment of trade standard.

Development of a Computer Program for Analyzing Preliminary Aircraft Configurations in Relationship to Emerging Agility Metrics

NASA Technical Reports Server (NTRS)

Bauer, Brent

1993-01-01

This paper discusses the development of a FORTRAN computer code to perform agility analysis on aircraft configurations. This code is to be part of the NASA-Ames ACSYNT (AirCraft SYNThesis) design code. This paper begins with a discussion of contemporary agility research in the aircraft industry and a survey of a few agility metrics. The methodology, techniques and models developed for the code are then presented. Finally, example trade studies using the agility module along with ACSYNT are illustrated. These trade studies were conducted using a Northrop F-20 Tigershark aircraft model. The studies show that the agility module is effective in analyzing the influence of common parameters such as thrust-to-weight ratio and wing loading on agility criteria. The module can compare the agility potential between different configurations. In addition, one study illustrates the module's ability to optimize a configuration's agility performance.

Method of making an InAsSb/InAsSbP diode lasers

DOEpatents

Razeghi, Manijeh

1997-01-01

InAsSb/InAsSbP/InAs Double Heterostructures (DH) and Separate Confinement Heterostructure Multiple Quantum Well (SCH-MQW) structures are taught wherein the ability to tune to a specific wavelength within 3 .mu.m to 5 .mu.m is possible by varying the ratio of As:Sb in the active layer.

Low temperature Zn diffusion for GaSb solar cell structures fabrication

NASA Technical Reports Server (NTRS)

Sulima, Oleg V.; Faleev, Nikolai N.; Kazantsev, Andrej B.; Mintairov, Alexander M.; Namazov, Ali

1995-01-01

Low temperature Zn diffusion in GaSb, where the minimum temperature was 450 C, was studied. The pseudo-closed box (PCB) method was used for Zn diffusion into GaAs, AlGaAs, InP, InGaAs and InGaAsP. The PCB method avoids the inconvenience of sealed ampoules and proved to be simple and reproducible. The special design of the boat for Zn diffusion ensured the uniformality of Zn vapor pressure across the wafer surface, and thus the uniformity of the p-GaSb layer depth. The p-GaSb layers were studied using Raman scattering spectroscopy and the x-ray rocking curve method. As for the postdiffusion processing, an anodic oxidation was used for a precise thinning of the diffused GaSb layers. The results show the applicability of the PCB method for the large-scale production of the GaSb structures for solar cells.

Project-Method Fit: Exploring Factors That Influence Agile Method Use

ERIC Educational Resources Information Center

Young, Diana K.

2013-01-01

While the productivity and quality implications of agile software development methods (SDMs) have been demonstrated, research concerning the project contexts where their use is most appropriate has yielded less definitive results. Most experts agree that agile SDMs are not suited for all project contexts. Several project and team factors have been…

Agile Methods in Air Force Sustainment: Status and Outlook

DTIC Science & Technology

2014-10-01

manage for it through iterations, anticipation and adaptation  unleash creativity and innovation by recognizing that individuals are the ultimate...073561993X X X Agile Project Management : Creating Innovative Products – 2nd Edition Jim Highsmith ISBN 0321658396 X Agile Retrospectives...X Leading Change John Kotter ISBN 0875847471 X Leading Geeks: How to Manage and Lead the People Who Deliver Technology Paul Glen ISBN

Relation between the magnetization and the electrical properties of alloy GaSb-MnSb films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koplak, O. V.; Polyakov, A. A.; Davydov, A. B.

2015-06-15

The influence of the charge carrier concentration on the magnetic properties of GaSb-MnSb alloys is studied. The ferromagnetism of GaSb-MnSb films is caused by the presence of MnSb granules and manifests itself in both magnetometric measurements and the presence of an anisotropic magnetoresistance and the anomalous Hall effect. Electric conduction is executed by charge carriers (holes) in a GaSb matrix. The magnetization of clusters depends on stoichiometry and the concentration of Mn{sup 2+} and Mn{sup 3+} ions, which is specified by the film growth conditions. At high film growth temperatures, ferromagnetic clusters containing Mn{sup 2+} ions mainly form. At lowmore » growth temperatures, an antiferromagnetic phase containing Mn{sup 3+} ions forms.« less

Method of making an InAsSb/InAsSbP diode lasers

DOEpatents

Razeghi, M.

1997-08-19

InAsSb/InAsSbP/InAs Double Heterostructures (DH) and Separate Confinement Heterostructure Multiple Quantum Well (SCH-MQW) structures are taught wherein the ability to tune to a specific wavelength within 3 {micro}m to 5 {micro}m is possible by varying the ratio of As:Sb in the active layer. 9 figs.

Final Report of the NASA Office of Safety and Mission Assurance Agile Benchmarking Team

NASA Technical Reports Server (NTRS)

Wetherholt, Martha

2016-01-01

To ensure that the NASA Safety and Mission Assurance (SMA) community remains in a position to perform reliable Software Assurance (SA) on NASAs critical software (SW) systems with the software industry rapidly transitioning from waterfall to Agile processes, Terry Wilcutt, Chief, Safety and Mission Assurance, Office of Safety and Mission Assurance (OSMA) established the Agile Benchmarking Team (ABT). The Team's tasks were: 1. Research background literature on current Agile processes, 2. Perform benchmark activities with other organizations that are involved in software Agile processes to determine best practices, 3. Collect information on Agile-developed systems to enable improvements to the current NASA standards and processes to enhance their ability to perform reliable software assurance on NASA Agile-developed systems, 4. Suggest additional guidance and recommendations for updates to those standards and processes, as needed. The ABT's findings and recommendations for software management, engineering and software assurance are addressed herein.

Evaluation of agile designs in first-in-human (FIH) trials--a simulation study.

PubMed

Perlstein, Itay; Bolognese, James A; Krishna, Rajesh; Wagner, John A

2009-12-01

The aim of the investigation was to evaluate alternatives to standard first-in-human (FIH) designs in order to optimize the information gained from such studies by employing novel agile trial designs. Agile designs combine adaptive and flexible elements to enable optimized use of prior information either before and/or during conduct of the study to seamlessly update the study design. A comparison of the traditional 6 + 2 (active + placebo) subjects per cohort design with alternative, reduced sample size, agile designs was performed by using discrete event simulation. Agile designs were evaluated for specific adverse event models and rates as well as dose-proportional, saturated, and steep-accumulation pharmacokinetic profiles. Alternative, reduced sample size (hereafter referred to as agile) designs are proposed for cases where prior knowledge about pharmacokinetics and/or adverse event relationships are available or appropriately assumed. Additionally, preferred alternatives are proposed for a general case when prior knowledge is limited or unavailable. Within the tested conditions and stated assumptions, some agile designs were found to be as efficient as traditional designs. Thus, simulations demonstrated that the agile design is a robust and feasible approach to FIH clinical trials, with no meaningful loss of relevant information, as it relates to PK and AE assumptions. In some circumstances, applying agile designs may decrease the duration and resources required for Phase I studies, increasing the efficiency of early clinical development. We highlight the value and importance of useful prior information when specifying key assumptions related to safety, tolerability, and PK.

Chemical investigation of saponins in different parts of Panax notoginseng by pressurized liquid extraction and liquid chromatography-electrospray ionization-tandem mass spectrometry.

PubMed

Wan, Jian-Bo; Zhang, Qing-Wen; Hong, Si-Jia; Li, Peng; Li, Shao-Ping; Wang, Yi-Tao

2012-05-16

A pressurized liquid extraction (PLE) and high performance liquid chromatography-electrospray ionization tandem mass spectrometry (HPLC-ESI-MS/MS) method was developed for the qualitative determination of saponins in different parts of P. notoginseng, including rhizome, root, fibre root, seed, stem, leaf and flower. The samples were extracted using PLE. The analysis was achieved on a Zorbax SB-C18 column with gradient elution of acetonitrile and 8 mM aqueous ammonium acetate as mobile phase. The mass spectrometer was operated in the negative ion mode using the electrospray ionization, and a collision induced dissociation (CID) experiment was also carried out to aid the identification of compounds. Forty one saponins were identified in different parts of P. notoginseng according to the fragmentation patterns and literature reports, among them, 21 saponins were confirmed by comparing the retention time and ESI-MS data with those of standard compounds. The results showed that the chemical characteristics were obviously diverse in different parts of P. notoginseng, which is helpful for pharmacological evaluation and quality control of P. notoginseng.

Development and validation of an LC-MS method for determination of Karanjin in rat plasma: application to preclinical pharmacokinetics.

PubMed

Yi, Deliang; Wang, Zhihua; Yi, Longzhi

2015-04-01

A selective and sensitive liquid chromatography-mass spectrometry (MS) method was developed and validated for the determination of karanjin in rat plasma. The target analyte, together with the internal standard (warfarin), was extracted from rat plasma by liquid-liquid extraction with ethyl acetate. Chromatographic separation was performed on a ZORBAX SB-C18 column using a mixture of acetonitrile and 0.1% aqueous formic acid as the mobile phase with linear gradient elution. MS detection was performed on a single quadrupole MS by selected ion monitoring mode via a positive electrospray ionization source. The assay exhibited a linear dynamic range of 2.50-3,000 ng/mL for karanjin. The intra- and inter-day precision was <10.8%, and the intra- and inter-day accuracy was <9.2%. The validated method has been applied to the preclinical pharmacokinetic studies of karanjin following oral administration of 5, 10 and 20 mg/kg karanjin to rats. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Sb2O3/Ag/Sb2O3 Multilayer Transparent Conducting Films For Ultraviolet Organic Light-emitting Diode

NASA Astrophysics Data System (ADS)

Song, Chunyan; Zhang, Nan; Lin, Jie; Guo, Xiaoyang; Liu, Xingyuan

2017-01-01

A novel UV transparent conducting films based on Sb2O3/Ag/Sb2O3 (SAS) structure, which were prepared by an electron-beam thermal evaporation at room temperature. This SAS exhibits excellent electrical, optical and stable properties. Especially for UV region, the SAS has high transmittance of 80% at 306 nm and 92% at 335 nm, meanwhile achieving low sheet resistance ( ≤ 10 Ω sq-1). The UV OLED based on the SAS show competitive device performance. The UV OLED obtains the peak of UV electroluminescence at 376 nm and shows a very high maximum EQE of 4.1% with the maximum output power density of 5.18 mW cm-2. These results indicate that the potential of SAS applications in deep UV transparent electrodes and large-scale flexible transparent electronics.

Sb2O3/Ag/Sb2O3 Multilayer Transparent Conducting Films For Ultraviolet Organic Light-emitting Diode.

PubMed

Song, Chunyan; Zhang, Nan; Lin, Jie; Guo, Xiaoyang; Liu, Xingyuan

2017-01-25

A novel UV transparent conducting films based on Sb 2 O 3 /Ag/Sb 2 O 3 (SAS) structure, which were prepared by an electron-beam thermal evaporation at room temperature. This SAS exhibits excellent electrical, optical and stable properties. Especially for UV region, the SAS has high transmittance of 80% at 306 nm and 92% at 335 nm, meanwhile achieving low sheet resistance ( ≤ 10 Ω sq -1 ). The UV OLED based on the SAS show competitive device performance. The UV OLED obtains the peak of UV electroluminescence at 376 nm and shows a very high maximum EQE of 4.1% with the maximum output power density of 5.18 mW cm -2 . These results indicate that the potential of SAS applications in deep UV transparent electrodes and large-scale flexible transparent electronics.

W-Sb-Te phase-change material: A candidate for the trade-off between programming speed and data retention

NASA Astrophysics Data System (ADS)

Peng, Cheng; Wu, Liangcai; Rao, Feng; Song, Zhitang; Yang, Pingxiong; Song, Hongjia; Ren, Kun; Zhou, Xilin; Zhu, Min; Liu, Bo; Chu, Junhao

2012-09-01

W-Sb-Te phase-change material has been proposed to improve the performance of phase-change memory (PCM). Crystallization temperature, crystalline resistance, and 10-year data retention of Sb2Te increase markedly by W doping. The Wx(Sb2Te)1-x films crystallize quickly into a stable hexagonal phase with W uniformly distributing in the crystal lattice, which ensures faster SET speed and better operation stability for the application in practical device. PCM device based on W0.07(Sb2Te)0.93 shows ultrafast SET operation (6 ns) and good endurance (1.8 × 105 cycles). W-Sb-Te material is a promising candidate for the trade-off between programming speed and data retention.

Effects of Ankle Braces Upon Agility Course Performance in High School Athletes

PubMed Central

Beriau, Mark R.; Cox, William B.; Manning, James

1994-01-01

The purpose of this study was to compare the effects of wearing the AircastTM Sports Stirrup, AircastTM Training brace, Swede-OTM brace, and DonJoyTM Ankle Ligament Protector while running an agility course. Eighty-five high school athletes with no history of ankle injury and no experience in wearing any ankle support served as subjects. Each subject participated in four separate testing sessions. During sessions 1 and 4, subjects ran the agility course under the control (unbraced) conditions. Sessions 2 and 3 consisted of randomly wearing the ankle braces while running the agility course. A questionnaire concerning support, comfort, and restriction was completed by each subject after wearing each of the braces. An analysis of variance (ANOVA) with repeated measures revealed that a significant difference existed between the agility times. Tukey's post hoc test indicated that a significant difference existed between each ankle brace and the control 2 agility times as well as a control 1 and control 2 time difference. The control time difference was attributed to a learning effect. An ANOVA with repeated measures of only the four braces revealed that a significant difference existed between the agility times. Tukey's post hoc test showed the only difference was between the DonJoy Ankle Ligament Protector and the Aircast Training brace. We concluded: 1) there is limited practical performance effect upon agility while wearing an ankle brace; and 2) an athlete's perceived comfort, support, and performance restriction are contributing factors that may directly influence the effectiveness of ankle bracing. PMID:16558284

Crystal growth and characterization of bulk Sb2Te3 topological insulator

NASA Astrophysics Data System (ADS)

Sultana, Rabia; Gurjar, Ganesh; Patnaik, S.; Awana, V. P. S.

2018-04-01

The Sb2Te3 crystals are grown using the conventional self flux method via solid state reaction route, by melting constituent elements (Sb and Te) at high temperature (850 °C), followed by slow cooling (2 °C/h). As grown Sb2Te3 crystals are analysed for various physical properties by x-ray diffraction (XRD), Raman Spectroscopy, Scanning Electron Microscopy (SEM) coupled with Energy Dispersive x-ray Spectroscopy (EDAX) and electrical measurements under magnetic field (6 Tesla) down to low temperature (2.5 K). The XRD pattern revealed the growth of synthesized Sb2Te3 sample along (00l) plane, whereas the SEM along with EDAX measurements displayed the layered structure with near stoichiometric composition, without foreign contamination. The Raman scattering studies displayed known ({{{{A}}}1{{g}}}1, {{{{E}}}{{g}}}2 and {{{{A}}}1{{g}}}2) vibrational modes for the studied Sb2Te3. The temperature dependent electrical resistivity measurements illustrated the metallic nature of the as grown Sb2Te3 single crystal. Further, the magneto—transport studies represented linear positive magneto-resistance (MR) reaching up to 80% at 2.5 K under an applied field of 6 Tesla. The weak anti localization (WAL) related low field (±2 Tesla) magneto-conductance at low temperatures (2.5 K and 20 K) has been analysed and discussed using the Hikami—Larkin—Nagaoka (HLN) model. Summarily, the short letter reports an easy and versatile method for crystal growth of bulk Sb2Te3 topological insulator (TI) and its brief physical property characterization.

Phase Change Characteristics of InxSb40-xTe60 Chalcogenide Alloy for Phase Change Random Access Memory

NASA Astrophysics Data System (ADS)

Yun, Jae-Jin; Lee, Won-Jong

2011-07-01

The InxSb40-xTe60 alloy was selected as a new alternative phase change material for Ge2Sb2Te5 (GST) for phase change random access memory (PRAM). The crystal structure of InxSb40-xTe60 was an α(Sb2Te3) rhombohedral (a=b=c, α=β=γ≠90°) single phase with identical lattice parameters in a wide composition range of In (0-28 at. %). The crystallization temperature and melting point of InxSb40-xTe60 were in the ranges of 149-219 °C and 608-614 °C, respectively, and similar to those of GST. The electric properties of InxSb40-xTe60 with a wide composition range of In contents showed the typical PRAM properties such as current-voltage (I-V), resistance-voltage (R-V), and switching behavior. The reset current of InxSb40-xTe60 decreased with increasing In content and the low power consumption and good retention can be realized by controlling In content. The ratio of the cell resistance and sheet resistance of amorphous InxSb40-xTe60 to those crystalline InxSb40-xTe60 were almost the same as or larger than those of GST. The cycling endurance test of InxSb40-xTe60 with a wide range of In contents showed the comparable results to GST. InxSb40-xTe60 was concluded to be a very promising phase change material for PRAM.

[Sb{sub 4}Au{sub 4}Sb{sub 4}]{sup 2−}: A designer all-metal aromatic sandwich

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tian, Wen-Juan; You, Xue-Rui; Guo, Jin-Chang

We report on the computational design of an all-metal aromatic sandwich, [Sb{sub 4}Au{sub 4}Sb{sub 4}]{sup 2−}. The triple-layered, square-prismatic sandwich complex is the global minimum of the system from Coalescence Kick and Minima Hopping structural searches. Following a standard, qualitative chemical bonding analysis via canonical molecular orbitals, the sandwich complex can be formally described as [Sb{sub 4}]{sup +}[Au{sub 4}]{sup 4−}[Sb{sub 4}]{sup +}, showing ionic bonding characters with electron transfers in between the Sb{sub 4}/Au{sub 4}/Sb{sub 4} layers. For an in-depth understanding of the system, one needs to go beyond the above picture. Significant Sb → Au donation and Sb ←more » Au back-donation occur, redistributing electrons from the Sb{sub 4}/Au{sub 4}/Sb{sub 4} layers to the interlayer Sb–Au–Sb edges, which effectively lead to four Sb–Au–Sb three-center two-electron bonds. The complex is a system with 30 valence electrons, excluding the Sb 5s and Au 5d lone-pairs. The two [Sb{sub 4}]{sup +} ligands constitute an unusual three-fold (π and σ) aromatic system with all 22 electrons being delocalized. An energy gap of ∼1.6 eV is predicted for this all-metal sandwich. The complex is a rare example for rational design of cluster compounds and invites forth-coming synthetic efforts.« less

Surface friction alters the agility of a small Australian marsupial.

PubMed

Wheatley, Rebecca; Clemente, Christofer J; Niehaus, Amanda C; Fisher, Diana O; Wilson, Robbie S

2018-04-23

Movement speed can underpin an animal's probability of success in ecological tasks. Prey often use agility to outmanoeuvre predators; however, faster speeds increase inertia and reduce agility. Agility is also constrained by grip, as the foot must have sufficient friction with the ground to apply the forces required for turning. Consequently, ground surface should affect optimum turning speed. We tested the speed-agility trade-off in buff-footed antechinus ( Antechinus mysticus ) on two different surfaces. Antechinus used slower turning speeds over smaller turning radii on both surfaces, as predicted by the speed-agility trade-off. Slipping was 64% more likely on the low-friction surface, and had a higher probability of occurring the faster the antechinus were running before the turn. However, antechinus compensated for differences in surface friction by using slower pre-turn speeds as their amount of experience on the low-friction surface increased, which consequently reduced their probability of slipping. Conversely, on the high-friction surface, antechinus used faster pre-turn speeds in later trials, which had no effect on their probability of slipping. Overall, antechinus used larger turning radii (0.733±0.062 versus 0.576±0.051 m) and slower pre-turn (1.595±0.058 versus 2.174±0.050 m s -1 ) and turning speeds (1.649±0.061 versus 2.01±0.054 m s -1 ) on the low-friction surface. Our results demonstrate the interactive effect of surface friction and the speed-agility trade-off on speed choice. To predict wild animals' movement speeds, future studies should examine the interactions between biomechanical trade-offs and terrain, and quantify the costs of motor mistakes in different ecological activities. © 2018. Published by The Company of Biologists Ltd.

The section TiInSe/sub 2/-TiSbSe/sub 2/ of the system Ti-In-Sb-Se

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guseinov, G.D.; Chapanova, L.M.; Mal'sagov, A.U.

1985-09-01

The ternary compounds A /SUP I/ B /SUP III/ C/sub 2/ /SUP VI/ (A /SUP I/ is univalent Ti; B /SUP III/ is Ga or In; and C /SUP VI/ is S, Se or Te) form a class of semiconductors with a large number of different gap widths. The compounds crystallize in the chalcopyrite structure. Solid solutions based on these compounds, which permit varying smoothly the gap width and other physical parameters over wide limits, are of great interest. The authors synthesized the compounds TiInSe/sub 2/ and TiSbSe/sub 2/ from the starting materials Ti-000, In-000, Sb-000 and Se-OSCh-17-4 by directmore » fusion of the components, taken in a stoichiometric ratio, in quartz ampules evacuated to 1.3 X 10/sup -3/ Pa and sealed.« less

First GRB detections with the AGILE Minicalorimeter

NASA Astrophysics Data System (ADS)

Marisaldi, M.; Labanti, C.; Fuschino, F.; Galli, M.; Tavani, M.; Bulgarelli, A.; Gianotti, F.; Trifoglio, M.; Argan, A.

2008-05-01

The Minicalorimeter (MCAL) onboard the AGILE satellite is a 1400 cm2 scintillation detector sensitive in the energy range 0.3-200 MeV. MCAL works both as a slave of the AGILE Silicon Tracker and as an autonomous detector for transient events (BURST mode). A dedicated onboard Burst Search logic scans BURST mode data in search of count rate increase. Peculiar characteristics of the detector are the high energy spectral coverage and a timing resolution of about 2 microseconds. Even if a trigger is not issued, BURST mode data are used to build a broad band energy spectrum (scientific ratemeters) organized in 11 bands for each of the two MCAL detection planes, with a time resolution of 1 second. After the first engineering commissioning phase, following the AGILE launch on 23rd April 2007, between 22nd June and 5th November 2007 eighteen GRBs were detected offline in the scientific ratemeters data, with a detection rate of about one per week. In this paper the capabilities of the detector will be described and an overview of the first detected GRBs will be given.

Ab Initio Molecular Dynamics Studies of Pb m Sb n ( m + n ≤ 9) Alloy Clusters

NASA Astrophysics Data System (ADS)

Song, Bingyi; Xu, Baoqiang; Yang, Bin; Jiang, Wenlong; Chen, Xiumin; Xu, Na; Liu, Dachun; Dai, Yongnian

2017-10-01

Structure, stability, and dynamics of Pb m Sb n ( m + n ≤ 9) clusters were investigated using ab initio molecular dynamics. Size dependence of binding energies, the second-order energy difference of clusters, dissociation energy, HOMO-LUMO gaps, Mayer bond order, and the diffusion coefficient of Pb m Sb n clusters were discussed. Results suggest that Pb3Sb2, Pb4Sb2, and Pb5Sb4 ( n = 2 or 4) clusters have higher stability than other clusters, which is consistent with previous findings. In case of Pb-Sb alloy, the dynamics results show that Pb4Sb2 (Pb-22.71 wt pct Sb) can exist in gas phase at 1073 K (800 °C), which reasonably explains the azeotropic phenomenon, and the calculated values are in agreement with the experimental results (Pb-22 wt pct Sb).

Optical parameters of diode lasers based on an InAsSb/InAsSbP heterostructure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Astakhova, A. P.; Bez'yazychnaya, T. V.; Burov, L. I.

2008-02-15

The rates of radiative recombination (including transitions induced by enhanced luminescence) and nonradiative recombination, internal quantum yield of luminescence, and the matrix element for band-to-band optical transitions were determined for the first time for InAsSb/InAsSbP diode lasers oscillating at wavelengths of 3.1-3.2 {mu}m. It is established that the contribution of nonradiative recombination to the lasing threshold can be as large as 97%. The internal quantum yield of luminescence for the InAs{sub 0.97}Sb{sub 0.03} compound is no higher than 3%. Most likely, the nonradiative channel is formed with involvement of Auger recombination with the constant C = 4.2 Multiplication-Sign 10{sup -38}more » m{sup 6}s{sup -1} (T = 77 K). The studied samples of lasers feature relatively low optical losses {rho} = 900 m{sup -1} and internal quantum efficiency of emission at the level of 0.6. The spontaneous lifetime of nonequilibrium charge carriers as determined from the radiative-recombination rate is equal to 6 Multiplication-Sign 10{sup -8} s, which is consistent with known published data.« less

Optical parameters of diode lasers based on an InAsSb/InAsSbP heterostructure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Astakhova, A. P.; Bez'yazychnaya, T. V.; Burov, L. I.

2008-02-15

The rates of radiative recombination (including transitions induced by enhanced luminescence) and nonradiative recombination, internal quantum yield of luminescence, and the matrix element for band-to-band optical transitions were determined for the first time for InAsSb/InAsSbP diode lasers oscillating at wavelengths of 3.1-3.2 {mu}m. It is established that the contribution of nonradiative recombination to the lasing threshold can be as large as 97%. The internal quantum yield of luminescence for the InAs{sub 0.97}Sb{sub 0.03} compound is no higher than 3%. Most likely, the nonradiative channel is formed with involvement of Auger recombination with the constant C = 4.2 x 10{sup -38}more » m{sup 6}s{sup -1} (T = 77 K). The studied samples of lasers feature relatively low optical losses {rho} = 900 m{sup -1} and internal quantum efficiency of emission at the level of 0.6. The spontaneous lifetime of nonequilibrium charge carriers as determined from the radiative-recombination rate is equal to 6 x 10{sup -8} s, which is consistent with known published data.« less

Surface phase stability and surfactant behavior of InAsSb alloy surfaces.

NASA Astrophysics Data System (ADS)

Anderson, Evan M.; Lundquist, Adam M.; Pearson, Chris; Millunchick, Joanna M.

InAsSb has the narrowest bandgap of any of the conventional III-V semiconductors: low enough for long wavelength infrared applications. Such devices are sensitive to point defects, which can be detrimental to performance. To control these defects, all aspects of synthesis must be considered, especially the atomic bonding at the surface. We use an ab initio statistical mechanics approach that combines density functional theory with a cluster expansion formalism to determine the stable surface reconstructions of Sb (As) on InAs (InSb) substrates. The surface phase diagram of Sb on InAs is dominated by Sb-dimer termination α2(2x4) and β2(2x4) and c(4x4). Smaller regions of mixed Sb-As dimers appear for high Sb chemical potentials and intermediate As chemical potential. We propose that InAsSb films could be grown on (2x4), which maintain bulk-like stoichiometry, to eliminate the formation of typically observed n-type defects. Scanning tunneling microscopy and reflection high energy electron diffraction confirm the calculated phase diagram. Based on these calculations, we propose a new mechanism for the surfactant behavior of Sb in these materials. We gratefully acknowledge Chakrapani Varanasi and the support of the Department of Defense, Army Research Office via the Grant Number W911NF-12-1-0338.

AGILE/GRID Science Alert Monitoring System: The Workflow and the Crab Flare Case

NASA Astrophysics Data System (ADS)

Bulgarelli, A.; Trifoglio, M.; Gianotti, F.; Tavani, M.; Conforti, V.; Parmiggiani, N.

2013-10-01

During the first five years of the AGILE mission we have observed many gamma-ray transients of Galactic and extragalactic origin. A fast reaction to unexpected transient events is a crucial part of the AGILE monitoring program, because the follow-up of astrophysical transients is a key point for this space mission. We present the workflow and the software developed by the AGILE Team to perform the automatic analysis for the detection of gamma-ray transients. In addition, an App for iPhone will be released enabling the Team to access the monitoring system through mobile phones. In 2010 September the science alert monitoring system presented in this paper recorded a transient phenomena from the Crab Nebula, generating an automated alert sent via email and SMS two hours after the end of an AGILE satellite orbit, i.e. two hours after the Crab flare itself: for this discovery AGILE won the 2012 Bruno Rossi prize. The design of this alert system is maximized to reach the maximum speed, and in this, as in many other cases, AGILE has demonstrated that the reaction speed of the monitoring system is crucial for the scientific return of the mission.

Modeling the thermal conductivities of the zinc antimonides ZnSb and Zn4Sb3

NASA Astrophysics Data System (ADS)

Bjerg, Lasse; Iversen, Bo B.; Madsen, Georg K. H.

2014-01-01

ZnSb and Zn4Sb3 are interesting as thermoelectric materials because of their low cost and low thermal conductivity. We introduce a model of the lattice thermal conductivity which is independent of fitting parameters and takes the full phonon dispersions into account. The model is found to give thermal conductivities with the correct relative magnitudes and in reasonable quantitative agreement with experiment for a number of semiconductor structures. The thermal conductivities of the zinc antimonides are reviewed and the relatively large effect of nanostructuring on the zinc antimonides is rationalized in terms of the mean free paths of the heat carrying phonons. The very low thermal conductivity of Zn4Sb3 is found to be intrinsic to the structure. However, the low-lying optical modes are observed in both Zn-Sb structures and involve both Zn and Sb vibrations, thereby strongly questioning dumbbell rattling. A mechanism for the very low thermal conductivity observed in Zn4Sb3 is identified. The large Grüneisen parameter of this compound is traced to the Sb atoms which coordinate only Zn atoms.

Limiting scattering processes in high-mobility InSb quantum wells grown on GaSb buffer systems

NASA Astrophysics Data System (ADS)

Lehner, Ch. A.; Tschirky, T.; Ihn, T.; Dietsche, W.; Keller, J.; Fält, S.; Wegscheider, W.

2018-05-01

We present molecular beam epitaxial grown single- and double-side δ -doped InAlSb/InSb quantum wells with varying distances down to 50 nm to the surface on GaSb metamorphic buffers. We analyze the surface morphology as well as the impact of the crystalline quality on the electron transport. Comparing growth on GaSb and GaAs substrates indicates that the structural integrity of our InSb quantum wells is solely determined by the growth conditions at the GaSb/InAlSb transition and the InAlSb barrier growth. The two-dimensional electron gas samples show high mobilities of up to 349 000 cm2/Vs at cryogenic temperatures and 58 000 cm2/Vs at room temperature. With the calculated Dingle ratio and a transport lifetime model, ionized impurities predominantly remote from the quantum well are identified as the dominant source of scattering events. The analysis of the well-pronounced Shubnikov-de Haas oscillations reveals a high spin-orbit coupling with an effective g -factor of -38.4 in our samples. Along with the smooth surfaces and long mean free paths demonstrated, our InSb quantum wells are increasingly competitive for nanoscale implementations of Majorana mode devices.

Team-based work and work system balance in the context of agile manufacturing.

PubMed

Yauch, Charlene A

2007-01-01

Manufacturing agility is the ability to prosper in an environment characterized by constant and unpredictable change. The purpose of this paper is to analyze team attributes necessary to facilitate agile manufacturing, and using Balance Theory as a framework, it evaluates the potential positive and negative impacts related to these team attributes that could alter the balance of work system elements and resulting "stress load" experienced by persons working on agile teams. Teams operating within the context of agile manufacturing are characterized as multifunctional, dynamic, cooperative, and virtual. A review of the literature relevant to each of these attributes is provided, as well as suggestions for future research.

Red Teaming Agility (Briefing Charts)

DTIC Science & Technology

2014-06-01

are termed “ antifragile ”. Black Swan Model for Deep Red Futures The future is dominated not by trends, but by outliers, extreme events that lie...disproportionately higher mission impact. Agility is a measure of antifragile systems Red Teaming Defined Red Teaming is a function to provide

Rapid determination of benzodiazepines, zolpidem and their metabolites in urine using direct injection liquid chromatography-tandem mass spectrometry.

PubMed

Jeong, Yu-Dong; Kim, Min Kyung; Suh, Sung Ill; In, Moon Kyo; Kim, Jin Young; Paeng, Ki-Jung

2015-12-01

Benzodiazepines and zolpidem are generally prescribed as sedative, hypnotics, anxiolytics or anticonvulsants. These drugs, however, are frequently misused in drug-facilitated crime. Therefore, a rapid and simple liquid chromatography-tandem mass spectrometric (LC-MS/MS) method was developed for identification and quantification of benzodiazepines, zolpidem and their metabolites in urine using deuterium labeled internal standards (IS). Urine samples (120 μL) mixed with 80 μL of the IS solution were centrifuged. An aliquot (5 μL) of the sample solution was directly injected into the LC-MS/MS system for analysis. The mobile phases consisted of water and acetonitrile containing 2mM ammonium trifluoroacetate and 0.2% acetic acid. The analytical column was a Zorbax SB-C18 (100 mm × 2.1 mm i.d., 3.5 μm, Agilent). The separation and detection of 18 analytes were achieved within 10 min. Calibration curves were linear over the concentration ranges of 0.5-20 ng/mL (zolpidem), 1.0-40 ng/mL (flurazepam and temazepam), 2.5-100 ng/mL (7-aminoclonazepam, 1-hydroxymidazolam, midazolam, flunitrazepam and alprazolam), 5.0-200 ng/mL (zolpidem phenyl-4-carboxylic acid, α-hydroxyalprazolam, oxazepam, nordiazepam, triazolam, diazepam and α-hydroxytriazolam), 10-400 ng/mL (lorazepam and desalkylflurazepam) and 10-100 ng/mL (N-desmethylflunitrazepam) with the coefficients of determination (r(2)) above 0.9971. The dilution integrity of the analytes was examined for supplementation of short linear range. Dilution precision and accuracy were tested using two, four and ten-folds dilutions and they ranged from 3.7 to 14.4% and -12.8 to 12.5%, respectively. The process efficiency for this method was 63.0-104.6%. Intra- and inter-day precisions were less than 11.8% and 9.1%, while intra- and inter-day accuracies were less than -10.0 to 8.2%, respectively. The lower limits of quantification were lower than 10 ng/mL for each analyte. The applicability of the developed method was successfully

SB265610 is an allosteric, inverse agonist at the human CXCR2 receptor

PubMed Central

Bradley, ME; Bond, ME; Manini, J; Brown, Z; Charlton, SJ

2009-01-01

Background and purpose: In several previous studies, the C-X-C chemokine receptor (CXCR)2 antagonist 1-(2-bromo-phenyl)-3-(7-cyano-3H-benzotriazol-4-yl)-urea (SB265610) has been described as binding competitively with the endogenous agonist. This is in contrast to many other chemokine receptor antagonists, where the mechanism of antagonism has been described as allosteric. Experimental approach: To determine whether it displays a unique mechanism among the chemokine receptor antagonists, the mode of action of SB265610 was investigated at the CXCR2 receptor using radioligand and [35S]-GTPγS binding approaches in addition to chemotaxis of human neutrophils. Key results: In equilibrium saturation binding studies, SB265610 depressed the maximal binding of [125I]-interleukin-8 ([125I]-IL-8) without affecting the Kd. In contrast, IL-8 was unable to prevent binding of [3H]-SB265610. Kinetic binding experiments demonstrated that this was not an artefact of irreversible or slowly reversible binding. In functional experiments, SB265610 caused a rightward shift of the concentration-response curves to IL-8 and growth-related oncogene α, but also a reduction in maximal response elicited by each agonist. Fitting these data to an operational allosteric ternary complex model suggested that, once bound, SB265610 completely blocks receptor activation. SB265610 also inhibited basal [35S]-GTPγS binding in this preparation. Conclusions and implications: Taken together, these data suggest that SB265610 behaves as an allosteric inverse agonist at the CXCR2 receptor, binding at a region distinct from the agonist binding site to prevent receptor activation, possibly by interfering with G protein coupling. PMID:19422399

Thermoelectric Performance and Defect Chemistry in n-Type Zintl KGaSb 4

DOE PAGES

Ortiz, Brenden R.; Gorai, Prashun; Stevanovic, Vladan; ...

2017-05-08

The rise of high-throughput calculations has accelerated the discovery of promising classes of thermoelectric materials. In prior work, we identified the n-type Zintl pnictides as one such material class. To date, however, a lack of detailed defect calculations and chemical intuition has led the community to investigate p-type Zintls almost exclusively. Here, we investigate the synthesis, thermoelectric properties, and defect structure of the complex Zintl KGaSb 4. We find that KGaSb 4 is successfully doped n-type with Ba and has the potential for p-type doping with Zn. Our calculations reveal the fundamental defect structure in KGaSb 4 that enables n-typemore » and p-type doping. We find that Ba doped KGaSb4 exhibits high electronic mobility (~50 cm 2V -1s -1) and near minimum lattice thermal conductivity (<0.5 Wm -1K -1) at 400 °C. Samples doped with 1.5% Ba achieve zT > 0.9 at 400 °C, promising for a previously unstudied material. Here, we also briefly investigate the series of alloys between KGaSb 4 and KAlSb 4, finding that a full solid solution exists. Altogether our work reinforces motivation for the exploration of n-type Zintl materials, especially in tandem with high-throughput defect calculations to inform selection of effective dopants and systems amenable to n-type transport.« less

Thermoelectric Performance and Defect Chemistry in n-Type Zintl KGaSb 4

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ortiz, Brenden R.; Gorai, Prashun; Stevanovic, Vladan

The rise of high-throughput calculations has accelerated the discovery of promising classes of thermoelectric materials. In prior work, we identified the n-type Zintl pnictides as one such material class. To date, however, a lack of detailed defect calculations and chemical intuition has led the community to investigate p-type Zintls almost exclusively. Here, we investigate the synthesis, thermoelectric properties, and defect structure of the complex Zintl KGaSb 4. We find that KGaSb 4 is successfully doped n-type with Ba and has the potential for p-type doping with Zn. Our calculations reveal the fundamental defect structure in KGaSb 4 that enables n-typemore » and p-type doping. We find that Ba doped KGaSb4 exhibits high electronic mobility (~50 cm 2V -1s -1) and near minimum lattice thermal conductivity (<0.5 Wm -1K -1) at 400 °C. Samples doped with 1.5% Ba achieve zT > 0.9 at 400 °C, promising for a previously unstudied material. Here, we also briefly investigate the series of alloys between KGaSb 4 and KAlSb 4, finding that a full solid solution exists. Altogether our work reinforces motivation for the exploration of n-type Zintl materials, especially in tandem with high-throughput defect calculations to inform selection of effective dopants and systems amenable to n-type transport.« less

Element-specific study of the temperature dependent magnetization of Co-Mn-Sb thin films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schmalhorst, J.; Ebke, D.; Meinert, M.

Magnetron sputtered thin Co-Mn-Sb films were investigated with respect to their element-specific magnetic properties. Stoichiometric Co{sub 1}Mn{sub 1}Sb{sub 1} crystallized in the C1{sub b} structure has been predicted to be half-metallic and is therefore of interest for spintronics applications. It should show a characteristic antiferromagnetic coupling of the Mn and Co magnetic moments and a transition temperature T{sub C} of about 480K. Although the observed transition temperature of our 20nm thick Co{sub 32.4}Mn{sub 33.7}Sb{sub 33.8}, Co{sub 37.7}Mn{sub 34.1}Sb{sub 28.2} and Co{sub 43.2}Mn{sub 32.6}Sb{sub 24.2} films is in quite good agreement with the expected value, we found a ferromagnetic coupling ofmore » the Mn and Co magnetic moments which indicates that the films do not crystallize in the C1{sub b} structure and are probably not fully spin-polarized. The ratio of the Co and Mn moments does not change up to the transition temperature and the temperature dependence of the magnetic moments can be well described by the mean field theory.« less

Study of conformational changes and protein aggregation of bovine serum albumin in presence of Sb(III) and Sb(V).

PubMed

Verdugo, Marcelo; Ruiz Encinar, Jorge; Costa-Fernández, José Manuel; Menendez-Miranda, Mario; Bouzas-Ramos, Diego; Bravo, Manuel; Quiroz, Waldo

2017-01-01

Antimony is a metalloid that affects biological functions in humans due to a mechanism still not understood. There is no doubt that the toxicity and physicochemical properties of Sb are strongly related with its chemical state. In this paper, the interaction between Sb(III) and Sb(V) with bovine serum albumin (BSA) was investigated in vitro by fluorescence spectroscopy, and circular dichroism (CD) under simulated physiological conditions. Moreover, the coupling of the separation technique, asymmetric flow field-flow fractionation, with elemental mass spectrometry to understand the interaction of Sb(V) and Sb(III) with the BSA was also used. Our results showed a different behaviour of Sb(III) vs. Sb(V) regarding their effects on the interaction with the BSA. The effects in terms of protein aggregates and conformational changes were higher in the presence of Sb(III) compared to Sb(V) which may explain the differences in toxicity between both Sb species in vivo. Obtained results demonstrated the protective effect of GSH that modifies the degree of interaction between the Sb species with BSA. Interestingly, in our experiments it was possible to detect an interaction between BSA and Sb species, which may be related with the presence of labile complex between the Sb and a protein for the first time.

Agile informatics: application of agile project management to the development of a personal health application.

PubMed

Chung, Jeanhee; Pankey, Evan; Norris, Ryan J

2007-10-11

We describe the application of the Agile method-- a short iteration cycle, user responsive, measurable software development approach-- to the project management of a modular personal health record, iHealthSpace, to be deployed to the patients and providers of a large academic primary care practice.

Robust ferroelectricity in two-dimensional SbN and BiP.

PubMed

Liu, Chang; Wan, Wenhui; Ma, Jie; Guo, Wei; Yao, Yugui

2018-05-03

Based on first-principles calculations, we discover two new two-dimensional (2D) ferroelectric materials SbN and BiP. Both of them are stable in a phosphorene-like structure and maintain their ferroelectricity above room temperature. Till date, SbN has the largest in-plane spontaneous polarization of about 7.81 × 10-10 C m-1 ever found in 2D ferroelectric materials, and it can retain its ferroelectricity until melting at about 1700 K. The spontaneous polarizations and switching barriers can easily be tuned by strains. Additionally, the ferroelectricity can still be maintained in their multilayers. These advantages make SbN and BiP promising candidate materials for future integrated ferroelectric devices.

Sb2O3/Ag/Sb2O3 Multilayer Transparent Conducting Films For Ultraviolet Organic Light-emitting Diode

PubMed Central

Song, Chunyan; Zhang, Nan; Lin, Jie; Guo, Xiaoyang; Liu, Xingyuan

2017-01-01

A novel UV transparent conducting films based on Sb2O3/Ag/Sb2O3 (SAS) structure, which were prepared by an electron-beam thermal evaporation at room temperature. This SAS exhibits excellent electrical, optical and stable properties. Especially for UV region, the SAS has high transmittance of 80% at 306 nm and 92% at 335 nm, meanwhile achieving low sheet resistance ( ≤ 10 Ω sq−1). The UV OLED based on the SAS show competitive device performance. The UV OLED obtains the peak of UV electroluminescence at 376 nm and shows a very high maximum EQE of 4.1% with the maximum output power density of 5.18 mW cm−2. These results indicate that the potential of SAS applications in deep UV transparent electrodes and large-scale flexible transparent electronics. PMID:28120888

Isolating GaSb membranes grown metamorphically on GaAs substrates using highly selective substrate removal etch processes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lavrova, Olga; Balakrishnan, Ganesh

2017-02-24

The etch rates of NH 4OH:H 2O 2 and C 6H 8O 7:H 2O 2 for GaAs and GaSb have been investigated to develop a selective etch for GaAs substrates and to isolate GaSb epilayers grown on GaAs. The NH 4OH:H 2O 2 solution has a greater etch rate differential for the GaSb/GaAs material system than C 6H 8O 7:H 2O 2 solution. The selectivity of NH 4OH:H 2O 2 for GaAs/GaSb under optimized etch conditions has been observed to be as high as 11471 ± 1691 whereas that of C 6H 8O 7:H 2O 2 has been measured upmore » to 143 ± 2. The etch contrast has been verified by isolating 2 μm thick GaSb epi-layers that were grown on GaAs substrates. GaSb membranes were tested and characterized with high-resolution X-Ray diffraction (HR-XRD) and atomic force microscopy (AFM).« less

SU-E-T-610: Comparison of Treatment Times Between the MLCi and Agility Multileaf Collimators

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ramsey, C; Bowling, J

2014-06-01

Purpose: The Agility is a new 160-leaf MLC developed by Elekta for use in their Infinity and Versa HD linacs. As compared to the MLCi, the Agility increased the maximum leaf speed from 2 cm/s to 3.5 cm/s, and the maximum primary collimator speed from 1.5 cm/s to 9.0 cm/s. The purpose of this study was to determine if the Agility MLC resulted in improved plan quality and/or shorter treatment times. Methods: An Elekta Infinity that was originally equipped with a 80 leaf MLCi was upgraded to an 160 leaf Agility. Treatment plan quality was evaluated using the Pinnacle planningmore » system with SmartArc. Optimization was performed once for the MLCi and once for the Agility beam models using the same optimization parameters and the same number of iterations. Patient treatment times were measured for all IMRT, VMAT, and SBRT patients treated on the Infinity with the MLCi and Agility MLCs. Treatment times were extracted from the EMR and measured from when the patient first walked into the treatment room until exiting the treatment room. Results: 11,380 delivery times were measured for patients treated with the MLCi, and 1,827 measurements have been made for the Agility MLC. The average treatment times were 19.1 minutes for the MLCi and 20.8 minutes for the Agility. Using a t-test analysis, there was no difference between the two groups (t = 0.22). The dose differences between patients planned with the MLCi and the Agility MLC were minimal. For example, the dose difference for the PTV, GTV, and cord for a head and neck patient planned using Pinnacle were effectively equivalent. However, the dose to the parotid glands was slightly worse with the Agility MLC. Conclusion: There was no statistical difference in treatment time, or any significant dosimetric difference between the Agility MLC and the MLCi.« less

Optimizing the Carrier Density and Thermoelectric Properties of Sb2Te3 Films by Using the Growth Temperature

NASA Astrophysics Data System (ADS)

Thiet, Duong Van; Quang, Nguyen Van; Hai, Nguyen Thi Minh; Huong, Nguyen Thi; Cho, Sunglae; Tuan, Duong Anh; Dung, Dang Duc; Tam, Tran Van

2018-04-01

In this work, we report on the structural and thermoelectric properties of Sb2Te3 films deposited on GaSb(111) substrates by using molecular beam epitaxy. The effects of the growth temperature on the microstructure and thermoelectric properties of the films were investigated. The results show that Sb2Te3 films grow on GaSb(111) along (00l) axis normal to the substrate and have a hexagonal structure with a layer-by-layer growth mode in growth temperature range from 200 to 250 °C while at 175 and 300 °C, the films show an island growth mode. Te and Sb2Te3 phases coexist at a growth temperature of 175 °C. The films exhibit a metallic behavior for growth temperatures below 250 °C and a semiconductor behavior at 300 °C. By changing growth temperature, we were able to vary the carrier density from 9.96×1018 to 4.55×1019 cm -3. At room temperature, the Seebeck coefficients are 110, 146, and 138 μV/K for growth temperatures of 175, 200 and 250 °C, respectively, and a large value of the power factor 61.67 μW/cm-K2 is achieved for the film grown at 250 °C.

Smart Healthcare Agility Management - Tojisha Doctrine by Self-synchronization

DTIC Science & Technology

2014-06-01

impossibility at our age. One is the technology of space elevator and another is the space-walk tourism which the project has existed since the mid-20 th...In regards to the technologies of space-walk tourism , increase of patents related to the technologies of Pulse Detention Engine worldwide is some...medicine, and there is some reference cases such as "open agility" and "closed agility" is immersed in training specifically in sports science which

The mini-calorimeter of the AGILE satellite

NASA Astrophysics Data System (ADS)

Labanti, C.; Marisaldi, M.; Fuschino, F.; Galli, M.; Argan, A.; Bulgarelli, A.; Costa, E.; Di Cocco, G.; Gianotti, F.; Tavani, M.; Trifoglio, M.

2006-06-01

AGILE is a small space mission of the Italian Space Agency (ASI) devoted to astrophysics in the gamma-ray energy range 30 MeV - 50 GeV, and in the X-ray band 15 keV - 45 keV. The AGILE Payload is composed of three instruments: a gamma-ray imager based on a Tungsten-Silicon Tracker (ST), for observations in the gamma ray energy range 30 MeV - 50 GeV, a Silicon based X-ray detector, Super-Agile (SA), for imaging in the range 15 keV - 40 keV and a CsI(Tl) Mini-Calorimeter (MCAL) that detects gamma rays or particle energy deposits between 300 keV and 200 MeV. The payload is currently fully integrated and the satellite is expected to be launched in the second half of 2006. MCAL is composed of 30 CsI(Tl) scintillator detectors with the shape of a bar with photodiode readout at both ends, arranged in two orthogonal layers. MCAL can work both as a slave of the ST and as an independent gamma-ray detector for the detection of transients and Gamma Ray Bursts. In this paper a detailed description of MCAL is presented together with the first on ground calibration results.

Assessment of Specificity of the Badcamp Agility test for Badminton Players

PubMed Central

de França Bahia Loureiro, Luiz; Costa Dias, Mário Oliveira; Cremasco, Felipe Couto; da Silva, Maicon Guimarães; de Freitas, Paulo Barbosa

2017-01-01

Abstract The Badcamp agility test was created to evaluate agility of badminton players. The Badcamp is a valid and reliable test, however, a doubt about the need for the use of this test exists as simpler tests could provide similar information about agility in badminton players. Thus, the aim of this study was to examine the specificity of the Badcamp, comparing the performance of badminton players and athletes from other sports in the Badcamp and the shuttle run agility test (SRAT). Sixty-four young male and female athletes aged between 14 and 16 years participated in the study. They were divided into 4 groups of 16 according to their sport practices: badminton, tennis, team sport (basketball and volleyball), and track and field. We compared the groups in both tests, the Badcamp and SRAT. The results revealed that the group of badminton players was faster compared to all other groups in the Badcamp. However, in the SRAT there were no differences among groups composed of athletes from open skill sports (e.g., badminton, tennis, and team sports), and a considerable reduction of the difference between badminton players and track and field athletes. Thus, we concluded that the Badcamp test is a specific agility test for badminton players and should be considered in evaluating athletes of this sport modality. PMID:28713471

Assessment of Specificity of the Badcamp Agility test for Badminton Players.

PubMed

de França Bahia Loureiro, Luiz; Costa Dias, Mário Oliveira; Cremasco, Felipe Couto; da Silva, Maicon Guimarães; de Freitas, Paulo Barbosa

2017-06-01

The Badcamp agility test was created to evaluate agility of badminton players. The Badcamp is a valid and reliable test, however, a doubt about the need for the use of this test exists as simpler tests could provide similar information about agility in badminton players. Thus, the aim of this study was to examine the specificity of the Badcamp, comparing the performance of badminton players and athletes from other sports in the Badcamp and the shuttle run agility test (SRAT). Sixty-four young male and female athletes aged between 14 and 16 years participated in the study. They were divided into 4 groups of 16 according to their sport practices: badminton, tennis, team sport (basketball and volleyball), and track and field. We compared the groups in both tests, the Badcamp and SRAT. The results revealed that the group of badminton players was faster compared to all other groups in the Badcamp. However, in the SRAT there were no differences among groups composed of athletes from open skill sports (e.g., badminton, tennis, and team sports), and a considerable reduction of the difference between badminton players and track and field athletes. Thus, we concluded that the Badcamp test is a specific agility test for badminton players and should be considered in evaluating athletes of this sport modality.

Effects of annealing and additions on dynamic mechanical properties of SnSb quenched alloy

NASA Astrophysics Data System (ADS)

El-Bediwi, A. B.

2004-08-01

The elastic modulus, internal friction and stiffness values of quenched SnSb bearing alloy have been evaluated using the dynamic resonance technique. Annealing for 2 and 4 h at 120, 140 and 160degreesC caused variations in the elastic modulus. internal friction and stiffness values. This is due to structural changes in the SnSb matrix during isothermal annealing such as coarsening in the phases (Sn, Sb or intermetallic compounds), recrystallization and stress relief. In addition, adding a small amount (1 wt.%) of Cu or Ag improved the bearing mechanical properties of the SnSb bearing alloy. The SnSbCu1 alloy has the best bearing mechanical properties with thermo-mechanical stability for long time at high temperature.

Survey-based analysis of risk factors for injury among dogs participating in agility training and competition events.

PubMed

Cullen, Kimberley L; Dickey, James P; Bent, Leah R; Thomason, Jeffrey J; Moëns, Noel M M

2013-10-01

To identify potential risk factors for agility-related injuries among dogs. Internet-based, retrospective, cross-sectional survey. 3,801 privately owned dogs participating in agility training or trials. A retrospective electronic survey was used to investigate potential risk factors for injury among dogs participating in agility-related activities. Respondents were handlers recruited through member lists of large canine agility associations in Canada and the United Kingdom and through promotion on an agility blog site. Variables evaluated included demographic information for handlers and dogs, exposure variables (eg, frequency of agility practice and competition in the past year), and use of preventive measures intended to keep dogs fit for agility (warmup, cooldown, or conditioning exercises; alternative therapeutic treatments [eg, acupuncture, massage, or chiropractic care]; or dietary supplement products). Data were collected from 1,669 handlers of 3,801 agility dogs internationally; 1,209 (32%) dogs incurred ≥ 1 injury. Previous injury (OR, 100.5), ≤ 4 years of agility experience for dogs (OR, 1.5), use of alternative therapeutic treatments (OR, 1.5), and Border Collie breed (OR, 1.7) were associated with increased odds of injury. Handlers having 5 to 10 or > 10 years of experience (OR, 0.8 and 0.6, respectively) and dogs having > 4 years of experience in the sport (OR, 0.6) were associated with decreased odds of injury. Specific factors were associated with agility-related injuries in dogs. Educational prevention strategies should target at-risk populations in an effort to reduce potential injuries. Future research should focus on the biomechanical factors associated with agility-related injuries.

A Virtual World Workshop Environment for Learning Agile Software Development Techniques

ERIC Educational Resources Information Center

Parsons, David; Stockdale, Rosemary

2012-01-01

Multi-User Virtual Environments (MUVEs) are the subject of increasing interest for educators and trainers. This article reports on a longitudinal project that seeks to establish a virtual agile software development workshop hosted in the Open Wonderland MUVE, designed to help learners to understand the basic principles of some core agile software…

Hydrazine solution processed Sb2S3, Sb2Se3 and Sb2(S1−xSex)3 film: molecular precursor identification, film fabrication and band gap tuning

PubMed Central

Yang, Bo; Xue, Ding-Jiang; Leng, Meiying; Zhong, Jie; Wang, Liang; Song, Huaibing; Zhou, Ying; Tang, Jiang

2015-01-01

Sb2(S1−xSex)3 (0 ≤ x ≤ 1) compounds have been proposed as promising light-absorbing materials for photovoltaic device applications. However, no systematic study on the synthesis and characterization of polycrystalline Sb2(S1−xSex)3 thin films has been reported. Here, using a hydrazine based solution process, single-phase Sb2(S1−xSex)3 films were successfully obtained. Through Raman spectroscopy, we have investigated the dissolution mechanism of Sb in hydrazine: 1) the reaction between Sb and S/Se yields [Sb4S7]2-/[Sb4Se7]2- ions within their respective solutions; 2) in the Sb-S-Se precursor solutions, Sb, S, and Se were mixed on a molecular level, facilitating the formation of highly uniform polycrystalline Sb2(S1−xSex)3 thin films at a relatively low temperature. UV-vis-NIR transmission spectroscopy revealed that the band gap of Sb2(S1−xSex)3 alloy films had a quadratical relationship with the Se concentration x and it followed the equation , where the bowing parameter was 0.118 eV. Our study provides a valuable guidance for the adjustment and optimization of the band gap in hydrazine solution processed Sb2(S1−xSex)3 alloy films for the future fabrication of improved photovoltaic devices. PMID:26042519

The Added Diagnostic Value of 18F-Fluorodihydroxyphenylalanine PET/CT in the Preoperative Work-Up of Small Bowel Neuroendocrine Tumors.

PubMed

Addeo, Pietro; Poncet, Gilles; Goichot, Bernard; Leclerc, Loic; Brigand, Cécile; Mutter, Didier; Romain, Benoit; Namer, Izzie-Jacques; Bachellier, Philippe; Imperiale, Alessio

2018-04-01

The precise localization of the primary tumor and/or the identification of multiple primary tumors improves the preoperative work-up in patients with small bowel (SB) neuroendocrine tumor (NET). The present study assesses the diagnostic value of 18 F-fluorodihydroxyphenylalanine ( 18 F-FDOPA) positron emission tomography/computed tomography (PET/CT) during the preoperative wok-up of SB NETs. Between January 2010 and June 2017, all consecutive patients with SB NETs undergoing preoperative 18 F-FDOPA PET/CT and successive resection were analyzed. Preoperative work-up included computed tomography (CT), somatostatin receptor scintigraphy (SRS), and 18 F-FDOPA PET/CT. Sensitivity and accuracy ratio for primary and multiple tumor detection were compared with data from surgery and pathology. There were 17 consecutive patients with SB NETs undergoing surgery. Nine patients (53%) had multiple tumors, 15 (88%) metastatic lymph nodes, 3 (18%) peritoneal carcinomatosis, and 9 patients (53%) liver metastases. A total of 70 SB NETs were found by pathology. Surgery identified the primary in 17/17 (100%) patients and recognized seven of 9 patients (78%) with multiple synchronous SB. Preoperatively, 18 F-FDOPA PET/CT displayed a statistically significant higher sensitivity for primary tumor localization (100 vs. 23.5 vs. 29.5%) and multiple tumor detection (78 vs. 22 vs. 11%) over SRS and CT. Compared with pathology, 18 F-FDOPA PET/CT displayed the highest accuracy ratio for number of tumor detected over CT and SRS (2.0 ± 2.2 vs. 0.4 ± 0.7 vs. 0.6 ± 1.5, p = 0.0003). 18 F-FDOPA PET/CT significantly increased the sensitivity and accuracy for primary and multiple SB NET identification. 18 F-FDOPA PET/CT should be included systematically in the preoperative work-up of SB NET.

Effect of lanthanide contraction on the mixed polyamine systems Ln/Sb/Se/(en+dien) and Ln/Sb/Se/(en+trien): Syntheses and characterizations of lanthanide complexes with a tetraelenidoantimonate ligand

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhao Jing; Liang Jingjing; Pan Yingli

Mixed polyamine systems Ln/Sb/Se/(en+dien) and Ln/Sb/Se/(en+trien) (Ln=lanthanide, en=ethylenediamine, dien=diethylenetriamine, trien=triethylenetetramine) were investigated under solvothermal conditions, and novel mixed-coordinated lanthanide(III) complexes [Ln(en){sub 2}(dien)({eta}{sup 2}-SbSe{sub 4})] (Ln=Ce(1a), Nd(1b)), [Ln(en){sub 2}(dien)(SbSe{sub 4})] (Ln=Sm(2a), Gd(2b), Dy(2c)), [Ln(en)(trien)({mu}-{eta}{sup 1},{eta}{sup 2}-SbSe{sub 4})]{sub {infinity}} (Ln=Ce(3a), Nd(3b)) and [Sm(en)(trien)({eta}{sup 2}-SbSe{sub 4})] (4a) were prepared. Two structural types of lanthanide selenidoantimonates were obtained across the lanthanide series in both en+dien and en+trien systems. The tetrahedral anion [SbSe{sub 4}]{sup 3-} acts as a monodentate ligand mono-SbSe{sub 4}, a bidentate chelating ligand {eta}{sup 2}-SbSe{sub 4} or a tridentate bridging ligand {mu}-{eta}{sup 1},{eta}{sup 2}-SbSe{sub 4} to the lanthanide(III) center depending on themore » Ln{sup 3+} ions and the mixed ethylene polyamines, indicating the effect of lanthanide contraction on the structures of the lanthanide(III) selenidoantimonates. The lanthanide selenidoantimonates exhibit semiconducting properties with E{sub g} between 2.08 and 2.51 eV. - Graphical Abstract: Two structural types of lanthanide(III) selenidoantimonates are formed in both en-dien and en-trien mixed polyamines across lanthanide series, indicating the lanthanide contraction effect on the structures of the lanthanide(III) selenidoantimonates. Highlights: > Two structural types of lanthanide selenidoantimonates are prepared across the lanthanide series in both Ln/Sb/Se/(en+dien) and Ln/Sb/Se/(en+trien) systems. > The [SbSe{sub 4}]{sup 3-} anion acts as a mono-SbSe{sub 4}, a {eta}{sup 2}-SbSe{sub 4} or a {mu}-{eta}{sup 1},{eta}{sup 2}-SbSe{sub 4} ligand to the Ln{sup 3+} ions. > The soft base ligand [SbSe{sub 4}]{sup 3-} can be controlled to coordinate to the Ln{sup 3+} ions with en+dien and en+trien as co-ligands.« less

Impact of process temperature on GaSb metal-oxide-semiconductor interface properties fabricated by ex-situ process

NASA Astrophysics Data System (ADS)

Yokoyama, Masafumi; Asakura, Yuji; Yokoyama, Haruki; Takenaka, Mitsuru; Takagi, Shinichi

2014-06-01

We have studied the impact of process temperature on interface properties of GaSb metal-oxide-semiconductor (MOS) structures fabricated by an ex-situ atomic-layer-deposition (ALD) process. We have found that the ALD temperature strongly affects the Al2O3/GaSb MOS interface properties. The Al2O3/GaSb MOS interfaces fabricated at the low ALD temperature of 150 °C have the minimum interface-trap density (Dit) of ˜4.5 × 1013 cm-2 eV-1. We have also found that the post-metalization annealing at temperature higher than 200 °C degrades the Al2O3/GaSb MOS interface properties. The low-temperature process is preferable in fabricating GaSb MOS interfaces in the ex-situ ALD process to avoid the high-temperature-induced degradations.

Clustering-based urbanisation to improve enterprise information systems agility

NASA Astrophysics Data System (ADS)

Imache, Rabah; Izza, Said; Ahmed-Nacer, Mohamed

2015-11-01

Enterprises are daily facing pressures to demonstrate their ability to adapt quickly to the unpredictable changes of their dynamic in terms of technology, social, legislative, competitiveness and globalisation. Thus, to ensure its place in this hard context, enterprise must always be agile and must ensure its sustainability by a continuous improvement of its information system (IS). Therefore, the agility of enterprise information systems (EISs) can be considered today as a primary objective of any enterprise. One way of achieving this objective is by the urbanisation of the EIS in the context of continuous improvement to make it a real asset servicing enterprise strategy. This paper investigates the benefits of EISs urbanisation based on clustering techniques as a driver for agility production and/or improvement to help managers and IT management departments to improve continuously the performance of the enterprise and make appropriate decisions in the scope of the enterprise objectives and strategy. This approach is applied to the urbanisation of a tour operator EIS.

The Effect of Acceleration Sprint and Zig-zag Drill Combination to Increase Students’ Speed and Agility

NASA Astrophysics Data System (ADS)

Bana, O.; Mintarto, E.; Kusnanik, N. W.

2018-01-01

The purpose of this research is to analyze the following factors: (1) how far the effect of exercise acceleration sprint on the speed and agility (2) how much influence the zig-zag drill combination to the speed and agility (3) and is there any difference between the effects of exercise acceleration sprint and practice zig-zag drill combination of the speed and agility. This research is quantitative with quasi-experimental approach. The design of this study is matching only design.This study was conducted on 33 male students who take part in extracurricular and divided into 3 groups with 11 students in each group. Group 1 was given training of acceleration sprint, group 2 was given zig-zag training combination drills of conventional and exercises for group 3, for 8 weeks. The data collection was using sprint 30 meter to test the speed and agility t-test to test agility. Data were analyzed using t-test and analysis of variance. The conclusion of the research is (1) there is a significant effect of exercise acceleration sprint for the speed and agility, (2) there is a significant influence combination zig-zag drills, on speed and agility (3) and exercise acceleration sprint have more effect on the speed and agility.

Transitioning from Distributed and Traditional to Distributed and Agile: An Experience Report

NASA Astrophysics Data System (ADS)

Wildt, Daniel; Prikladnicki, Rafael

Global companies that experienced extensive waterfall phased plans are trying to improve their existing processes to expedite team engagement. Agile methodologies have become an acceptable path to follow because it comprises project management as part of its practices. Agile practices have been used with the objective of simplifying project control through simple processes, easy to update documentation and higher team iteration over exhaustive documentation, focusing rather on team continuous improvement and aiming to add value to business processes. The purpose of this chapter is to describe the experience of a global multinational company on transitioning from distributed and traditional to distributed and agile. This company has development centers across North America, South America and Asia. This chapter covers challenges faced by the project teams of two pilot projects, including strengths of using agile practices in a globally distributed environment and practical recommendations for similar endeavors.

Passivation of InSb surface for manufacturing infrared devices

NASA Astrophysics Data System (ADS)

Simchi, H.; Sareminia, Gh.; Shafiekhani, A.; Valizadeh, Gh.

2008-01-01

We studied the reduction of active surface states at the InSb/insulator interface by the reduction of hysteresis in C- V plots and by the performance of InSb diodes operated in photovoltaic mode. The InSb wafers were cleaned with CP4A etchant (HNO 3:CH 3COOH:HF:H 2O at 2:1:1:10). Then layers of 0.4 μm SiO 2, 0.4 μm Si 3N 4 and 0.5 μm Si 3N 4/SiO 2 were deposited on the cleaned surfaced by plasma enhanced chemical vapor deposition (PECVD). After measuring the surface morphology by atomic force microscopy (AFM) the atomic percentage of each element in each compound (e.g. Si and O 2 in SiO 2 layer) was studied by energy-dispersive X-ray spectroscopy (EDX). By using photoemission spectroscopy (XPS), we showed that the SiO 2, Si 3N 4 and Si 3N 4/SiO 2 layers include Sb and/or SbO x and the Sb In antisite during deposition occurred and for this reason their etch rates differ from pure SiO 2, Si 3N 4 and Si 3N 4/SiO 2 layers. Then the gold metal was deposited on the samples and capacitance voltage measurement was made on the MIS samples. The results showed hysteresis free curves if the surface has been cleaned correctly. Finally by depositing the 0.4 μm SiO 2, 0.4 μm Si 3N 4 and 0.5 μm Si 3N 4/SiO 2 on diode structure of InSb, the performance of diode in this case was compared with the anodic oxidation method. The results showed the performance of device is better than for the anodic oxidation method.

Effect of bath temperature on structure, morphology and thermoelectric properties of CoSb{sub 3} thin films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yadav, Suchitra, E-mail: suchitrayadav87@gmail.com; Pandya, Dinesh K.; Chaudhary, Sujeet

2016-05-23

CoSb{sub 3} thin films are deposited on conducting glass substrates (FTO) by electrodeposition at different bath temperatures (60°C, 70°C and 80°C) and the resulting influence of the bath temperature on the structure, morphology and electrical properties of films is investigated. X-ray diffraction confirms the formation of CoSb{sub 3} phase in the films. Scanning electron microscopy reveals that different morphologies ranging from branched nano-flakes to nano-needles evolve as bath temperature increases. It is concluded that a growth temperature of 80°C is suitable for producing CoSb{sub 3} films with such properties that show potential feasibility for thermoelectric applications.

High-temperature ferromagnetism in new n-type Fe-doped ferromagnetic semiconductor (In,Fe)Sb

NASA Astrophysics Data System (ADS)

Thanh Tu, Nguyen; Hai, Pham Nam; Anh, Le Duc; Tanaka, Masaaki

2018-06-01

Over the past two decades, intensive studies on various ferromagnetic semiconductor (FMS) materials have failed to realize reliable FMSs that have a high Curie temperature (T C > 300 K), good compatibility with semiconductor electronics, and characteristics superior to those of their nonmagnetic host semiconductors. Here, we demonstrate a new n-type Fe-doped narrow-gap III–V FMS, (In1‑ x ,Fe x )Sb. Its T C is unexpectedly high, reaching ∼335 K at a modest Fe concentration (x) of 16%. The anomalous Hall effect and magnetic circular dichroism (MCD) spectroscopy indicate that the high-temperature ferromagnetism in (In,Fe)Sb thin films is intrinsic and originates from the zinc-blende (In,Fe)Sb alloy semiconductor.

Agile Infrastructure Monitoring

NASA Astrophysics Data System (ADS)

Andrade, P.; Ascenso, J.; Fedorko, I.; Fiorini, B.; Paladin, M.; Pigueiras, L.; Santos, M.

2014-06-01

At the present time, data centres are facing a massive rise in virtualisation and cloud computing. The Agile Infrastructure (AI) project is working to deliver new solutions to ease the management of CERN data centres. Part of the solution consists in a new "shared monitoring architecture" which collects and manages monitoring data from all data centre resources. In this article, we present the building blocks of this new monitoring architecture, the different open source technologies selected for each architecture layer, and how we are building a community around this common effort.

Agile Walking Robot

NASA Technical Reports Server (NTRS)

Larimer, Stanley J.; Lisec, Thomas R.; Spiessbach, Andrew J.; Waldron, Kenneth J.

1990-01-01

Proposed agile walking robot operates over rocky, sandy, and sloping terrain. Offers stability and climbing ability superior to other conceptual mobile robots. Equipped with six articulated legs like those of insect, continually feels ground under leg before applying weight to it. If leg sensed unexpected object or failed to make contact with ground at expected point, seeks alternative position within radius of 20 cm. Failing that, robot halts, examines area around foot in detail with laser ranging imager, and replans entire cycle of steps for all legs before proceeding.

Metabolism of 18-methoxycoronaridine, an ibogaine analog, to 18-hydroxycoronaridine by genetically variable CYP2C19.

PubMed

Zhang, Wenjiang; Ramamoorthy, Yamini; Tyndale, Rachel F; Glick, Stanley D; Maisonneuve, Isabelle M; Kuehne, Martin E; Sellers, Edward M

2002-06-01

18-Methoxycoronaridine, a newly developed ibogaine analog, has been reported to decrease the self-administration of morphine, cocaine, ethanol, and nicotine. It has also been reported to attenuate naltrexone-precipitated signs of morphine withdrawal. In this study, three metabolites of 18-methoxycoronaridine (18-MC) were separated and identified by high-performance liquid chromatography-electrospray ionization-mass spectrometry-mass spectrometry (HPLC-ESI-MS-MS); the major metabolite was 18-hydroxycoronaridine (18-HC). The other two metabolites were elucidated as hydroxylated metabolites on the basis of their MS-MS spectra. Catalytic studies of 18-MC O-demethylase activity in human liver microsomes indicate that one high affinity enzyme is involved in this reaction (K(m) from 2.81 to 7.9 microM; V(max) from 0.045 to 0.29 nmol/mg/min). In cDNA-expressing microsomes, only CYP2C19 displayed significant 18-MC O-demethylase activity (K(m) 1.34 microM; V(max) 0.21 nmol/mg/min). S-Mephenytoin, a selective CYP2C19 inhibitor, inhibited 18-MC O-demethylation by 65% at a concentration of 2 times its K(I), and antibodies against rat 2C (human CYP2C8, 2C9, 2C19) inhibited 18-HC formation by 70%. Studies with other cytochrome P450 (P450)-selective chemical inhibitors and antibodies failed to demonstrate an appreciable role for other P450s in this reaction. In addition, in microsomes from five different human livers, 18-MC O-demethylation correlated with S-mephenytoin 4'hydroxylase activity but not with other P450 probe reactions. These data indicate that 18-HC formation is the predominant pathway of 18-MC metabolism in vitro in human liver microsomes and that this metabolic pathway is primarily catalyzed by the polymorphic CYP2C19. The apparent selectivity of this pathway for CYP2C19 suggests 18-MC as a potentially useful probe of CYP2C19 activity in vitro and in vivo.

GPU-powered model analysis with PySB/cupSODA.

PubMed

Harris, Leonard A; Nobile, Marco S; Pino, James C; Lubbock, Alexander L R; Besozzi, Daniela; Mauri, Giancarlo; Cazzaniga, Paolo; Lopez, Carlos F

2017-11-01

A major barrier to the practical utilization of large, complex models of biochemical systems is the lack of open-source computational tools to evaluate model behaviors over high-dimensional parameter spaces. This is due to the high computational expense of performing thousands to millions of model simulations required for statistical analysis. To address this need, we have implemented a user-friendly interface between cupSODA, a GPU-powered kinetic simulator, and PySB, a Python-based modeling and simulation framework. For three example models of varying size, we show that for large numbers of simulations PySB/cupSODA achieves order-of-magnitude speedups relative to a CPU-based ordinary differential equation integrator. The PySB/cupSODA interface has been integrated into the PySB modeling framework (version 1.4.0), which can be installed from the Python Package Index (PyPI) using a Python package manager such as pip. cupSODA source code and precompiled binaries (Linux, Mac OS/X, Windows) are available at github.com/aresio/cupSODA (requires an Nvidia GPU; developer.nvidia.com/cuda-gpus). Additional information about PySB is available at pysb.org. paolo.cazzaniga@unibg.it or c.lopez@vanderbilt.edu. Supplementary data are available at Bioinformatics online. © The Author(s) 2017. Published by Oxford University Press.

Enthalpy of mixing of liquid systems for lead free soldering: Ni-Sb-Sn system.

PubMed

Elmahfoudi, A; Fürtauer, S; Sabbar, A; Flandorfer, H

2012-04-20

The partial and integral enthalpies of mixing of liquid ternary Ni-Sb-Sn alloys were determined along five sections x Sb / x Sn  = 3:1, x Sb / x Sn  = 1:1, x Sb / x Sn  = 1:3, x Ni / x Sn  = 1:4, and x Ni / x Sb  = 1:4 at 1000 °C in a large compositional range using drop calorimetry techniques. The mixing enthalpy of Ni-Sb alloys was determined at the same temperature and described by a Redlich-Kister polynomial. The other binary data were carefully evaluated from literature values. Our measured ternary data were fitted on the basis of an extended Redlich-Kister-Muggianu model for substitutional solutions. Additionally, a comparison of these results to the extrapolation model of Toop is given. The entire ternary system shows exothermic values of Δ mix H ranging from approx. -1300 J/mol, the minimum in the Sb-Sn binary system down to approx. -24,500 J/mol towards Ni-Sb. No significant ternary interaction could be deduced from our data.

An Integrated Toolset for Agile Systems Engineering Requirements Analysis

DTIC Science & Technology

2011-05-19

Tool STDUse Cases Collaboration Tool Data Mgmt T l 1 e a a managemen oo Run the test in the test lab, redline the STD Update the collaboration...Boeing Defense, Space & Security Lean-Agile Software A I t t d T l t fn n egra e oo se or Agile Systems Engineering Requirements Analysis Phyllis...Regulations (ITAR) and the Export Administration R l ti (EAR) h i l bl b t h th i th BOEING is a trademark of Boeing Management Company. Copyright © 2010

CT-assisted agile manufacturing

NASA Astrophysics Data System (ADS)

Stanley, James H.; Yancey, Robert N.

1996-11-01

The next century will witness at least two great revolutions in the way goods are produced. First, workers will use the medium of virtual reality in all aspects of marketing, research, development, prototyping, manufacturing, sales and service. Second, market forces will drive manufacturing towards small-lot production and just-in-time delivery. Already, we can discern the merging of these megatrends into what some are calling agile manufacturing. Under this new paradigm, parts and processes will be designed and engineered within the mind of a computer, tooled and manufactured by the offspring of today's rapid prototyping equipment, and evaluated for performance and reliability by advanced nondestructive evaluation (NDE) techniques and sophisticated computational models. Computed tomography (CT) is the premier example of an NDE method suitable for future agile manufacturing activities. It is the only modality that provides convenient access to the full suite of engineering data that users will need to avail themselves of computer- aided design, computer-aided manufacturing, and computer- aided engineering capabilities, as well as newly emerging reverse engineering, rapid prototyping and solid freeform fabrication technologies. As such, CT is assured a central, utilitarian role in future industrial operations. An overview of this exciting future for industrial CT is presented.

Modification of Agility Running Technique in Reaction to a Defender in Rugby Union

PubMed Central

Wheeler, Keane W.; Sayers, Mark G.L.

2010-01-01

Three-dimensional kinematic analysis examined agility running technique during pre-planned and reactive performance conditions specific to attacking ball carries in rugby union. The variation to running technique of 8 highly trained rugby union players was compared between agility conditions (pre-planned and reactive) and also agility performance speeds (fast, moderate and slow). Kinematic measures were used to determine the velocity of the centre of mass (COM) in the anteroposterior (running speed) and mediolateral (lateral movement speed) planes. The position of foot-strike and toe-off was also examined for the step prior to the agility side- step (pre-change of direction phase) and then the side-step (change of direction phase). This study demonstrated that less lateral movement speed towards the intended direction change occurred during reactive compared to pre-planned conditions at pre-change of direction (0.08 ± 0.28 m·s-1 and 0.42 ± 0.25 m·s-1, respectively) and change of direction foot-strikes (0.25 ± 0.42 m·s-1 and 0.69 ± 0.43 m·s-1, respectively). Less lateral movement speed during reactive conditions was associated with greater lateral foot displacement (44.52 ± 6.10% leg length) at the change of direction step compared to pre-planned conditions (41.35 ± 5.85%). Importantly, the anticipation abilities during reactive conditions provided a means to differentiate between speeds of agility performance, with faster performances displaying greater lateral movement speed at the change of direction foot- strike (0.52 ± 0.34 m·s-1) compared to moderate (0.20 ± 0.37 m·s-1) and slow (-0.08 ± 0.31 m·s-1). The changes to running technique during reactive conditions highlight the need to incorporate decision-making in rugby union agility programs. Key points Changes to running technique occur when required to make a decision. Fast agility performers use different stepping strategies in reactive conditions. Decision-making must be incorporated in

Type-II InAs/GaSb (InAsSb) superlattices for interband cascade midwavelength detectors

NASA Astrophysics Data System (ADS)

Hackiewicz, Klaudia; Martyniuk, Piotr

2018-02-01

Type-II superlattice (T2SL) interband cascade infrared detectors (IB CIDs) proved to be a promising candidate for short response time devices operating in room and higher temperatures. The current status of the higher operating temperature (HOT) T2SLs InAs/GaSb and InAs/InAsSb IB CID is presented. We compare both materials with HgCdTe alloy, which is widely described in literature. The detectivity of midwave infrared (MWIR) T2SLs InAs/GaSb and InAs/InAsSb based IB CID has been demonstrated up to 380 K.

Development and validation of a rapid and sensitive high-performance liquid chromatography-mass spectroscopy assay for determination of 17-(allylamino)-17-demethoxygeldanamycin and 17-(amino)-17-demethoxygeldanamycin in human plasma.

PubMed

Johnston, Jeffrey S; Phelps, Mitch A; Blum, Kristie A; Blum, William; Grever, Michael R; Farley, Katherine L; Dalton, James T

2008-08-01

A sensitive method was developed and validated for the measurement of 17-(allylamino)-17-demethoxygeldanamycin (17AAG) and its active metabolite 17-amino-17-demethoxygeldanamycin (17AG) in human plasma using 17-(dimethylaminoethylamino)-17-demethoxygeldanamycin (17DMAG) as an internal standard. After the addition of internal standard, 200 microL of plasma was extracted using ice cold acetonitrile followed by analysis on a Thermo Finnigan triple-quadruple mass spectrometer coupled to an Agilent 1100 HPLC system. Chromatography was carried out on a 50 mm x 2.1 mm Agilent Zorbax SB-phenyl 5 microm column coupled to a 3mm Varian metaguard diphenyl pre-column using glacial acetic acid 0.1% and a gradient of acetonitrile and water at a flow rate of 500 microL/min. Atmospheric pressure chemical ionization and detection of 17AAG, 17AG and 17DMAG were accomplished using selected reaction monitoring of m/z 584.3>541.3, 544.2>501.2, and 615.3>572.3, respectively in negative ion mode. Retention times for 17AAG, 17AG, and 17DMAG were 4.1, 3.5, and 2.9 min, respectively, with a total run time of 7 min. The assay was linear over the range 0.5-3000 ng/mL for 17AAG and 17AG. Replicate sample analysis indicated within- and between-run accuracy and precision within 15%. The recovery of 17AAG and 17AG from 200 microL of plasma containing 1, 25, 300, and 2500 ng/mL was 93% or greater. This high-performance liquid chromatographic tandem mass spectroscopy (HPLC/MS/MS) method is superior to previous methods. It is the first analytical method reported to date for the quantitation of both 17AAG and its metabolite 17AG and can reliably quantitate concentrations of both compounds as low as 0.5 ng/mL.

The OsO(3)F(+) and mu-F(OsO(3)F)(2)(+) cations: their syntheses and study by Raman and (19)F NMR spectroscopy and electron structure calculations and X-ray crystal structures of [OsO(3)F][PnF(6)] (Pn = As, Sb), [OsO(3)F][HF](2)[AsF(6)], [OsO(3)F][HF][SbF(6)], and [OsO(3)F][Sb(3)F(16)].

PubMed

Gerken, Michael; Dixon, David A; Schrobilgen, Gary J

2002-01-28

The fluoride ion donor properties of OsO(3)F(2) have been investigated. The salts [OsO(3)F][AsF(6)], [OsO(3)F][HF](2)[AsF(6)], mu-F(OsO(3)F)(2)[AsF(6)], [OsO(3)F][HF](2)[SbF(6)], and [OsO(3)F][HF][SbF(6)] have been prepared by reaction of OsO(3)F(2) with AsF(5) and SbF(5) in HF solvent and have been characterized in the solid state by Raman spectroscopy. The single-crystal X-ray diffraction studies of [OsO(3)F][AsF(6)] (P2(1)/n, a = 7.0001(11) A, c = 8.8629(13) A, beta = 92.270(7) degrees, Z = 4, and R(1) = 0.0401 at -126 degrees C), [OsO(3)F][SbF(6)] (P2(1)/c, a = 5.4772(14) A, b = 10.115(3) A, c = 12.234(3) A, beta = 99.321(5) degrees, Z = 4, and R(1) = 0.0325 at -173 degrees C), [OsO(3)F][HF](2)[AsF(6)] (P2(1)/n, a = 5.1491(9) A, b = 8.129(2) A, c = 19.636(7) A, beta = 95.099(7) degrees, Z = 4, and R(1) = 0.0348 at -117 degrees C), and [OsO(3)F][HF][SbF(6)] (Pc, a = 5.244(4) A, b = 9.646(6) A, c = 15.269(10) A, beta = 97.154(13) degrees, Z = 4, and R(1) = 0.0558 at -133 degrees C) have shown that the OsO(3)F(+) cations exhibit strong contacts to the anions and HF solvent molecules giving rise to cyclic, dimeric structures in which the osmium atoms have coordination numbers of 6. The reaction of OsO(3)F(2) with neat SbF(5) yielded [OsO(3)F][Sb(3)F(16)], which has been characterized by (19)F NMR spectroscopy in SbF(5) and SO(2)ClF solvents and by Raman spectroscopy and single-crystal X-ray diffraction in the solid state (P4(1)m, a = 10.076(6) A, c = 7.585(8) A, Z = 2, and R(1) = 0.0858 at -113 degrees C). The weak fluoride ion basicity of the Sb(3)F(16)(-) anion resulted in an OsO(3)F(+) cation (C(3)(v) point symmetry) that is well isolated from the anion and in which the osmium is four-coordinate. The geometrical parameters and vibrational frequencies of OsO(3)F(+), ReO(3)F, mu-F(OsO(3)F)(2)(+), (FO(3)Os--FPnF(5))(2), and (FO(3)Os--(HF)(2)--FPnF(5))(2) (Pn = As, Sb) have been calculated using density functional theory methods.

Low temperature grown GaNAsSb: A promising material for photoconductive switch application

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tan, K. H.; Yoon, S. F.; Wicaksono, S.

2013-09-09

We report a photoconductive switch using low temperature grown GaNAsSb as the active material. The GaNAsSb layer was grown at 200 °C by molecular beam epitaxy in conjunction with a radio frequency plasma-assisted nitrogen source and a valved antimony cracker source. The low temperature growth of the GaNAsSb layer increased the dark resistivity of the switch and shortened the carrier lifetime. The switch exhibited a dark resistivity of 10{sup 7} Ω cm, a photo-absorption of up to 2.1 μm, and a carrier lifetime of ∼1.3 ps. These results strongly support the suitability of low temperature grown GaNAsSb in the photoconductivemore » switch application.« less

Comparative NMR studies of diffusional water permeability of red blood cells from different species: XV. Agile wallaby (Macropus agilis), red-necked wallaby (Macropus rufogriseus) and Goodfellow's tree kangaroo (Dendrolagus goodfellowi).

PubMed

Benga, Gheorghe; Chapman, Bogdan E; Kuchel, Philip W

2009-09-01

The water diffusional permeability (P(d)) of red blood cells (RBC) from agile wallaby (Macropus agilis), red-necked wallaby (Macropus rufogriseus) and Goodfellow's tree kangaroo (Dendrolagus goodfellowi) was monitored using an Mn(2+)-doping (1)H nuclear magnetic resonance (NMR) technique at 400 MHz. The P(d) (cm s(-1)) values of agile wallaby RBCs were 7.5 x 10(-3) at 25 degrees C, 9 x 10(-3) at 30 degrees C, 11 x 10(-3) at 37 degrees C, and 13 x 10(-3) at 42 degrees C. The inhibitory effect of a mercury-containing sulfhydryl (SH)-modifying reagent p-chloromercuribenzoate (PCMB) on agile wallaby RBCs was investigated. The maximal inhibition was reached in 90 min at 37 degrees C with 2 mmol L(-1) PCMB. The value of maximal inhibition was approximately 63% when measured at 25 degrees C, approximately 52% at 37 degrees C and approximately 45% at 42 degrees C. The lowest value of P(d) (corresponding to the basal permeability to water) was approximately 3 x 10(-3) cm s(-1) at 25 degrees C. For the RBCs from red-necked wallaby (M. rufogriseus) the values of P(d) (cm s(-1)) were 7 x 10(-3) at 25 degrees C, 8 x 10(-3) at 30 degrees C, 10 x 10(-3) at 37 degrees C, and 12 x 10(-3) at 42 degrees C. Higher values of P(d) (cm s(-1)) were found for the RBCs from Goodfellow's tree kangaroo (D. goodfellowi): 8.5 x 10(-3) at 25 degrees C, 10 x 10(-3) at 30 degrees C, 13 x 10(-3) at 37 degrees C, and 15 x 10(-3) at 42 degrees C. The mean values of the activation energy of water diffusion (E(a,d)) were approximately 25 kJ mol(-1) for RBCs from the agile wallaby and tree kangaroo, respectively, and approximately 23 kJ mol(-1) for RBCs from red-necked wallaby. The values of E(a,d) increased after exposure of agile wallaby RBCs to PCMB, reaching a value of approximately 43-46 kJ mol(-1) when the maximal inhibition of P(d) was achieved.

Solvothermal synthesis of a new 3-D mixed-metal sulfide framework, (H1.33tren)[In2.67Sb1.33S8]·tren

NASA Astrophysics Data System (ADS)

Lampkin, John D.; Powell, Anthony V.; Chippindale, Ann M.

2016-11-01

A new indium(III) antimony(V) sulfide, (H1.33tren)[In2.67Sb1.33S8]·tren, has been prepared solvothermally at 433 K. The compound crystallises in the tetragonal space group I-42d (lattice parameters, a=12.6248(5) and c=19.4387(18) Å at 150 K) and contains adamantane-like T2 supertetrahedral units comprised of corner-sharing InS45- and SbS43- tetrahedra. The adamantane-like units are then linked through sulfur vertices to generate an open, 3-D framework structure containing large pores in which neutral, protonated tren (tris(2-aminoethylene)amine) molecules reside. The presence of the organic components was confirmed by solid-state 13C NMR (10 kHz), combustion and thermogravimetric analysis. The band gap, obtained from UV-vis diffuse reflectance measurements, is 2.7(2) eV. Stirring with either water or alkali-metal salt solution leads to removal of the neutral tren molecules and an 9% reduction in unit-cell volume on formation of (H1.33tren)[In2.67Sb1.33S8]·(H2O)4.

Agility and change of direction in soccer: differences according to the player ages.

PubMed

Fiorilli, Giovanni; Mitrotasios, Michalis; Iuliano, Enzo; Pistone, Eugenio M; Aquino, Giovanna; Calcagno, Giuseppe; DI Cagno, Alessandra

2017-12-01

The goal of this study was to compare the changes of direction speed (CODS) and reactive agility (RA) in soccer players of different ages, in order to optimize the best training of these skills. One hundred eighty-seven players, divided into bi-annual age-groups, U12, U14, U16 and U18, performed two tests: Y-Agility Test, carried out in planned and reactive mode (Y-PLAN and Y-REAC) and Illinois for Change of Direction Test (ICODT). Difference between Y-REAC minus Y-PLAN represents the index of reactivity (REAC-INDEX). MANOVA showed significant differences among groups (F3,182=14.591; P<0.01; η2p=0.244). Y-PLAN showed significant differences only between U12 and the other groups (P<0.01). ICODT results were significantly different between the groups U12 and U14 and the other groups (P<0.01). Significant Pearson's correlations between Y-TEST and ICODT, for the three categories of young players (0.398 P<0.05; 0.615 P<0.01; 0.608 P<0.01 respectively), were found, whereas no significant correlation was found in U18 group. The best performance of Y-PLAN and ICODT, through age, depends on physical skill level, whereas the best RA results depend on technique and experience that help the players to use anticipatory skill. The high correlations between CODS and RA performances, differently than adult athletes, suggest that an effective work program for young players may include RA and CODS training at the same time.

Lattice Dynamical, Elastic and Thermodynamical Properties of III-V Semiconductor AlSb, GaSb and Their Mixed Semiconductor Ga_{1-x}AlxSb

NASA Astrophysics Data System (ADS)

Kushwaha, A. K.

2017-07-01

A proposed eleven-parameter three-body shell model is used to study the lattice dynamical properties such as phonon dispersion relations along high symmetry directions, phonon density of states, variation of specific heat and Debye characteristic temperature with absolute temperature, elastic constants and related properties for III-V semiconductor AlSb, GaSb and their mixed semiconductor Ga_{1-x}AlxSb having zinc-blende structure. We found an overall good agreement with the available experimental and theoretical results available in the literature.

Bi flux-dependent MBE growth of GaSbBi alloys

DOE PAGES

Rajpalke, M. K.; Linhart, W. M.; Yu, K. M.; ...

2015-03-05

The incorporation of Bi in GaSb 1-xBi x alloys grown by molecular beam epitaxy is investigated as a function of Bi flux at fixed growth temperature (275 °C) and growth rate (1 μm h⁻¹). The Bi content is found to vary proportionally with Bi flux with Bi contents, as measured by Rutherford backscattering, in the range 0 < x ≤ 4.5%. The GaSbBi samples grown at the lowest Bi fluxes have smooth surfaces free of metallic droplets. The higher Bi flux samples have surface Bi droplets. The room temperature band gap of the GaSbBi epitaxial layers determined from optical absorptionmore » decreases linearly with increasing Bi content with a reduction of ~32 meV/%Bi.« less

The effects of the selective 5-HT(2C) receptor antagonist SB 242084 on learned helplessness in male Fischer 344 rats.

PubMed

Strong, Paul V; Greenwood, Benjamin N; Fleshner, Monika

2009-05-01

Rats exposed to an uncontrollable stressor demonstrate a constellation of behaviors such as exaggerated freezing and deficits in shuttle box escape learning. These behaviors in rats have been called learned helplessness and have been argued to model human stress-related mood disorders. Learned helplessness is thought to be caused by hyperactivation of serotonin (5-HT) neurons in the dorsal raphe nucleus (DRN) and a subsequent exaggerated release of 5-HT in DRN projection sites. Blocking 5-HT(2C) receptors in the face of an increase in serotonin can alleviate anxiety behaviors in some animal models. However, specific 5-HT receptor subtypes involved in learned helplessness remain unknown. The current experiments tested the hypothesis that 5-HT(2C) receptor activation is necessary and sufficient for the expression of learned helplessness. The selective 5-HT(2C) receptor antagonist SB 242084 (1.0 mg/kg) administered i.p. to adult male Fischer 344 rats prior to shuttle box behavioral testing, but not before stress, blocked stress-induced deficits in escape learning but had no effect on the exaggerated shock-elicited freezing. The selective 5-HT(2C) receptor agonist CP-809101 was sufficient to produce learned helplessness-like behaviors in the absence of prior stress and these effects were blocked by pretreatment with SB 242084. Results implicate the 5-HT(2C) receptor subtype in mediating the shuttle box escape deficits produced by exposure to uncontrollable stress and suggest that different postsynaptic 5-HT receptor subtypes underlie the different learned helplessness behaviors.

Undercooling and solidification behavior in the InSb-Sb system. M.S. Thesis. Final Report

NASA Technical Reports Server (NTRS)

Graves, J. A.

1985-01-01

Use of the droplet emulsion technique has been successful in studying the undercooling and crystallization behavior of Sb, InSb, and an InSb-Sb eutectic alloy. Both droplet size and imposed cooling rate were influential in controlling the extent of liquid undercooling. The droplet surface coating was of significant importance in determining the resultant solidification product structure through its effect on nucleation kinetics. The maximum undercooling for pure Sb was extended from 0.08 to 0.23 T sub m. While simple crushing techniques provided a dramatic increase in droplet undercooling over the bulk material, emulsification treatments both enhanced this undercooling and allowed successful formation of a metastable simple cubic Sb phase. This phase was stable to temperatures approaching the melting point. The simple cubic phase was detected in droplet samples processed using DTA, air and water quenching, and drop tube processing under a helium gas atmosphere. A deviation in the InSb parent ingot composition limited interpretation of the line compound results, however, emulsification techniques extended the undercooling of this material to 0.17 T sub L and provided a stable, protective surface coating for the droplets. Emulsification of the eutectic alloy was effective at producing various levels of undercooling from 0.1 to 0.2 T sub E. Microstructural examination revealed a normal-type eutectic structure in the undercooled droplets indicating that solidification occurred within the coupled zone and that this zone is somewhat symmetric about the eutectic composition.

Sb 121 , 123 nuclear quadrupole resonance as a microscopic probe in the Te-doped correlated semimetal FeSb 2 : Emergence of electronic Griffith phase, magnetism, and metallic behavior

DOE PAGES

Gippius, A. A.; Zhurenko, S. V.; Hu, R.; ...

2018-02-12

121,123Sb nuclear quadrupole resonance (NQR) was applied to Fe(Sb 1-xTe x) 2 in the low doping regime (x = 0 , 0.01, and 0.05) as a microscopic zero field probe to study the evolution of 3d magnetism and the emergence of metallic behavior. Whereas the NQR spectra itself reflects the degree of local disorder via the width of the individual NQR lines, the spin lattice relaxation rate (SLRR) 1/T 1 (T) probes the fluctuations at the Sb site. The fluctuations originate either from conduction electrons or from magnetic moments. In contrast to the semimetal FeSb 2 with a clear signaturemore » of the charge and spin gap formation in 1/T 1(T)T[~exp/(Δk BT)] , the 1% Te-doped system exhibits almost metallic conductivity and the SLRR nicely confirms that the gap is almost filled. A weak divergence of the SLRR coefficient 1/T 1(T)T ~ T -n ~ T -0.2 points towards the presence of electronic correlations towards low temperatures. This is supported by the electronic specific heat coefficient γ = (C el/T) showing a power-law divergence γ (T) ~ T -m ~ (1/T 1T) 1/2 ~ T -n/2 ~ C el/T which is expected in the renormalized Landau Fermi liquid theory for correlated electrons. In contrast to that the 5% Te-doped sample exhibits a much larger divergence in the SLRR coefficient showing 1/T 1(T)T ~ T -0.72 . According to the specific heat divergence a power law with n = 2 m = 0.56 is expected for the SLRR. This dissimilarity originates from admixed critical magnetic fluctuations in the vicinity of antiferromagnetic long range order with 1/T 1(T)T ~ T -3/4 behavior. Furthermore Te-doped FeSb 2 as a disordered paramagnetic metal might be a platform for the electronic Griffith phase scenario. NQR evidences a substantial asymmetric broadening of the 121,123Sb NQR spectrum for the 5% sample. Lastly, this has a predominant electronic origin in agreement with the electronic Griffith phase and stems probably from an enhanced Sb-Te bond polarization and electronic density shift towards the Te

Sb 121 , 123 nuclear quadrupole resonance as a microscopic probe in the Te-doped correlated semimetal FeSb 2 : Emergence of electronic Griffith phase, magnetism, and metallic behavior

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gippius, A. A.; Zhurenko, S. V.; Hu, R.

121,123Sb nuclear quadrupole resonance (NQR) was applied to Fe(Sb 1-xTe x) 2 in the low doping regime (x = 0 , 0.01, and 0.05) as a microscopic zero field probe to study the evolution of 3d magnetism and the emergence of metallic behavior. Whereas the NQR spectra itself reflects the degree of local disorder via the width of the individual NQR lines, the spin lattice relaxation rate (SLRR) 1/T 1 (T) probes the fluctuations at the Sb site. The fluctuations originate either from conduction electrons or from magnetic moments. In contrast to the semimetal FeSb 2 with a clear signaturemore » of the charge and spin gap formation in 1/T 1(T)T[~exp/(Δk BT)] , the 1% Te-doped system exhibits almost metallic conductivity and the SLRR nicely confirms that the gap is almost filled. A weak divergence of the SLRR coefficient 1/T 1(T)T ~ T -n ~ T -0.2 points towards the presence of electronic correlations towards low temperatures. This is supported by the electronic specific heat coefficient γ = (C el/T) showing a power-law divergence γ (T) ~ T -m ~ (1/T 1T) 1/2 ~ T -n/2 ~ C el/T which is expected in the renormalized Landau Fermi liquid theory for correlated electrons. In contrast to that the 5% Te-doped sample exhibits a much larger divergence in the SLRR coefficient showing 1/T 1(T)T ~ T -0.72 . According to the specific heat divergence a power law with n = 2 m = 0.56 is expected for the SLRR. This dissimilarity originates from admixed critical magnetic fluctuations in the vicinity of antiferromagnetic long range order with 1/T 1(T)T ~ T -3/4 behavior. Furthermore Te-doped FeSb 2 as a disordered paramagnetic metal might be a platform for the electronic Griffith phase scenario. NQR evidences a substantial asymmetric broadening of the 121,123Sb NQR spectrum for the 5% sample. Lastly, this has a predominant electronic origin in agreement with the electronic Griffith phase and stems probably from an enhanced Sb-Te bond polarization and electronic density shift towards the Te

Canted antiferromagnetism in phase-pure CuMnSb

NASA Astrophysics Data System (ADS)

Regnat, A.; Bauer, A.; Senyshyn, A.; Meven, M.; Hradil, K.; Jorba, P.; Nemkovski, K.; Pedersen, B.; Georgii, R.; Gottlieb-Schönmeyer, S.; Pfleiderer, C.

2018-05-01

We report the low-temperature properties of phase-pure single crystals of the half-Heusler compound CuMnSb grown by means of optical float zoning. The magnetization, specific heat, electrical resistivity, and Hall effect of our single crystals exhibit an antiferromagnetic transition at TN=55 K and a second anomaly at a temperature T*≈34 K. Powder and single-crystal neutron diffraction establish an ordered magnetic moment of (3.9 ±0.1 ) μB/f .u . , consistent with the effective moment inferred from the Curie-Weiss dependence of the susceptibility. Below TN, the Mn sublattice displays commensurate type-II antiferromagnetic order with propagation vectors and magnetic moments along <111 > (magnetic space group R [I ]3 c ). Surprisingly, below T*, the moments tilt away from <111 > by a finite angle δ ≈11∘ , forming a canted antiferromagnetic structure without uniform magnetization consistent with magnetic space group C [B ]c . Our results establish that type-II antiferromagnetism is not the zero-temperature magnetic ground state of CuMnSb as may be expected of the face-centered cubic Mn sublattice.

5th Annual AGILE Science Workshop

NASA Technical Reports Server (NTRS)

Hunter, Stanley

2008-01-01

The EGRET model of the galactic diffuse gamma-ray emission (GALDIF) has been extended to provide full-sky coverage and improved to address the discrepancies with the EGRET data. This improved model is compared with the AGILE results from the Galactic center. The comparison is discussed.

GaSb/AlGaSb VCSEL structures and microcavities in the 1.5 μm wavelength range

NASA Astrophysics Data System (ADS)

Koeth, J.; Dietrich, R.; Reithmaier, J. P.; Forchel, A.

Vertical cavity surface emitting laser structures for 1.5 μm wavelength applications were realized by growing AlSb/AlGaSb Bragg mirrors on GaAs substrates with solid source molecular beam epitaxy. Due to the high refractive index contrast between GaSb and AlSb high quality resonators can be made by only 15 layer pairs for each Bragg mirror. Laser operation could be demonstrated by optical pumping with threshold excitation densities of about 500 W/cm2. In laterally deeply etched microcavities with diameters of 5 μm a clear discretization of the optical modes was observed. The lateral confinement effects are compared with results of AlAs/GaAs microcavities designed for 0.9 μm emission wavelength. Due to the longer wavelength a stronger confinement effect can be achieved in AlSb/AlGaSb microcavities for the same lateral dimensions.

Impact of process temperature on GaSb metal-oxide-semiconductor interface properties fabricated by ex-situ process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yokoyama, Masafumi, E-mail: yokoyama@mosfet.t.u-tokyo.ac.jp; Takenaka, Mitsuru; Takagi, Shinichi

We have studied the impact of process temperature on interface properties of GaSb metal-oxide-semiconductor (MOS) structures fabricated by an ex-situ atomic-layer-deposition (ALD) process. We have found that the ALD temperature strongly affects the Al{sub 2}O{sub 3}/GaSb MOS interface properties. The Al{sub 2}O{sub 3}/GaSb MOS interfaces fabricated at the low ALD temperature of 150 °C have the minimum interface-trap density (D{sub it}) of ∼4.5 × 10{sup 13 }cm{sup −2} eV{sup −1}. We have also found that the post-metalization annealing at temperature higher than 200 °C degrades the Al{sub 2}O{sub 3}/GaSb MOS interface properties. The low-temperature process is preferable in fabricating GaSb MOS interfaces in the ex-situmore » ALD process to avoid the high-temperature-induced degradations.« less

The glass transition, crystallization and melting in Au-Pb-Sb alloys

NASA Technical Reports Server (NTRS)

Lee, M. C.; Allen, J. L.; Fecht, H. J.; Perepezko, J. H.; Ohsaka, K.

1988-01-01

The glass transition, crystallization and melting of Au(55)Pb(22.5)Sb(22.5) alloys have been studied by differential scanning calorimetry DSC. Crystallization on heating above the glass transition temperature Tg (45 C) begins at 64 C. Further crystallization events are observed at 172 C and 205 C. These events were found to correspond to the formation of the intermetallic compounds AuSb2, Au2Pb, and possibly AuPb2, respectively. Isothermal DSC scans of the glassy alloy above Tg were used to monitor the kinetics of crystallization. The solidification behavior and heat capacity in the glass-forming composition range were determined with droplet samples. An undercooling level of 0.3T(L) below the liquidus temperature T(L) was achieved, resulting in crystallization of different stable and metastable phases. The heat capacity C(P) of the undercooled liquid was measured over an undercooling range of 145 C.

Improvement of antimony sulfide photo absorber performance by interface modification in Sb2S3-ZnO hybrid nanostructures

NASA Astrophysics Data System (ADS)

Ali, Asad; Hasanain, Syed Khurshid; Ali, Tahir; Sultan, Muhammad

2017-03-01

Metal-oxide chalcogenide nanostructures as part of hybrid systems are very important for photovoltaic and optoelectronic applications. It is however known that the various interfaces within the hybrid structures play a crucial role in limiting the efficiency of these devices. Here we report on the improvement of Sb2S3 structure through modification of interface between Zn-oxide nanostructures and chalcogenides. ZnO nanorods were grown on fluorine doped tin oxide (FTO) substrate by chemical bath deposition (CBD) method. X-ray diffraction (XRD) and SEM analysis confirmed the single phase wurtzite structure and c-axis orientation of the ZnO nanorod arrays. Antimony tri-sulfide (Sb2S3) was deposited on ZnO nanords by CBD and subsequently annealed at 300 °C in argon environment for 30 min. XRD and the XPS analysis of ZnO-Sb2S3 system showed the dominant presence of Sb2O3 rather than Sb2S3. Since oxidation of Sb2S3 is understood to proceed mainly from the ZnO-Sb2S3 interface, a ZnS interlayer was introduced between ZnO nanorods and Sb2S3 by chemical route. The subsequent structural and optical properties of the ZnO-ZnS-Sb2S3 system are analyzed in detail. The introduction of sulfide interlayer prevents the oxidation of Sb2S3 which is evident from reduced oxide phase in Sb2S3. Significant improvement in the structural and optical properties of Sb2S3 are reported as compared to the parent ZnO-Sb2S3 system. This gain in the optical properties of hybrid ZnO-ZnS-Sb2S3 nanostructures is explained as being related to successful prevention of Sb2O3 formation at the Sb-ZnO interface and stabilization of the desired Sb2S3.

In-plane optical anisotropy of InAs/GaSb superlattices with alternate interfaces

PubMed Central

2013-01-01

The in-plane optical anisotropy (IPOA) in InAs/GaSb superlattices has been studied by reflectance difference spectroscopy (RDS) at different temperatures ranging from 80 to 300 K. We introduce alternate GaAs- and InSb-like interfaces (IFs), which cause the symmetry reduced from D2d to C2v. IPOA has been observed in the (001) plane along [110] and [11¯0] axes. RDS measurement results show strong anisotropy resonance near critical point (CP) energies of InAs and GaSb. The energy positions show red shift and RDS intensity decreases with the increasing temperature. For the superlattice sample with the thicker InSb-like IFs, energy positions show red shift, and the spectra exhibit stronger IPOA. The excitonic effect is clearly observed by RDS at low temperatures. It demonstrates that biaxial strain results in the shift of the CP energies and IPOA is enhanced by the further localization of the carriers in InSb-like IFs. PMID:23799946

FAST TRACK COMMUNICATION: Emission wavelength extension of mid-infrared InAsSb/InP nanostructures using InGaAsSb sandwich layers

NASA Astrophysics Data System (ADS)

Lei, W.; Tan, H. H.; Jagadish, C.

2010-08-01

This paper presents a study on the emission wavelength extension of InAsSb nanostructures using InGaAsSb sandwich layers. Due to the reduced lattice mismatch between InAsSb nanostructure layer and buffer/capping layer, the introduction of InGaAsSb sandwich layers leads to larger island size, reduced compressive strain and lower confinement barrier for InAsSb nanostructures, thus resulting in a longer emission wavelength. For InGaAsSb sandwich layers with nominal Sb concentration higher than 10%, type II band alignment is observed for the InAsSb/InGaAsSb heterostructure, which also contributes to the extension of emission wavelength. The InGaAsSb sandwich layers provide an effective approach to extend the emission wavelength of InAsSb nanostructures well beyond 2 µm, which is very useful for device applications in the mid-infrared region.

Determination of enantiomeric vigabatrin by derivatization with diacetyl-l-tartaric anhydride followed by ultra-high performance liquid chromatography-quadrupole-time-of-flight mass spectrometry.

PubMed

Zhao, Jing; Shin, Yujin; Jin, Yan; Jeong, Kyung Min; Lee, Jeongmi

2017-01-01

Vigabatrin, one of the most widely used antiepileptic drugs, is marketed and administered as a racemic mixture, while only S-enantiomer is therapeutically effective. In the present study, diacetyl-l-tartaric acid anhydride was used as an inexpensive and effective chiral derivatization reagent to produce tartaric acid monoester derivatives of vigabatrin enantiomers that could be readily resolved by reversed phase chromatography. Derivatization conditions were statistically optimized by response surface methodology, resulting in an optimal reaction temperature of 44°C and an optimal reaction time of 30min. The derivatized diastereomers of vigabatrin and internal standard (gabapentin) were analyzed using ultra-high performance liquid chromatography coupled to quadrupole-time-of-flight mass spectrometry. For this analysis, an Agilent ZORBAX Rapid Resolution High Definition Eclipse Plus C18 column (100mm×2.1mm, 1.8μm) was employed for chromatographic separation using 10mM ammonium formate (pH 3.0) and methanol as mobile phase at a flow rate of 0.2mLmin -1 . The established method was validated in terms of specificity, linearity, precision, accuracy, dilution integrity, recovery, matrix effect, stability, and incurred sample reanalysis. It was linear over a range of 0.25-100.0mgL -1 for both S- and R-enantiomers (R 2 ≥0.9987 for both). Intra- and inter-day precisions and accuracies were within acceptable ranges. The method was successfully applied to determine the levels of vigabatrin enantiomers in mouse serum after administration of vigabatrin racemate. Copyright © 2016 Elsevier B.V. All rights reserved.

Structure and magnetic properties of L n MnSbO ( L n = La and Ce)

DOE PAGES

Zhang, Qiang; Kumar, C. M. N.; Tian, Wei; ...

2016-03-11

Here, a neutron powder diffraction (NPD) study of LnMnSbO (Ln = La or Ce) reveals differences between the magnetic ground state of the two compounds due to the strong Ce-Mn coupling compared to La-Mn. The two compounds adopt the P4/nmm space group down to 2 K, and whereas magnetization measurements do not show obvious anomaly at high temperatures, NPD reveals a C-type antiferromagnetic (AFM) order below T N = 255K for LaMnSbO and 240 K for CeMnSbO. While the magnetic structure of LaMnSbO is preserved to base temperature, a sharp transition at T SR = 4.5K is observed in CeMnSbOmore » due to a spin-reorientation (SR) transition of the Mn 2+ magnetic moments from pointing along the c axis to the ab plane. The SR transition in CeMnSbO is accompanied by a simultaneous long-range AFM ordering of the Ce moments, which indicates that the Mn SR transition is driven by the Ce-Mn coupling. The ordered moments are found to be somewhat smaller than those expected for Mn 2+ (S = 5/2) in insulators, but large enough to suggest that these compounds belong to the class of local-moment antiferromagnets. The lower T N found in these two compounds compared to the As-based counterparts (T N = 317 for LaMnAsO, T N = 347K for CeMnAsO) indicates that the Mn-Pn (Pn=As or Sb) hybridization that mediates the superexchange Mn-Pn-Mn coupling is weaker for the Sb-based compounds.« less

Optical flows method for lightweight agile remote sensor design and instrumentation

NASA Astrophysics Data System (ADS)

Wang, Chong; Xing, Fei; Wang, Hongjian; You, Zheng

2013-08-01

Lightweight agile remote sensors have become one type of the most important payloads and were widely utilized in space reconnaissance and resource survey. These imaging sensors are designed to obtain the high spatial, temporary and spectral resolution imageries. Key techniques in instrumentation include flexible maneuvering, advanced imaging control algorithms and integrative measuring techniques, which are closely correlative or even acting as the bottle-necks for each other. Therefore, mutual restrictive problems must be solved and optimized. Optical flow is the critical model which to be fully represented in the information transferring as well as radiation energy flowing in dynamic imaging. For agile sensors, especially with wide-field-of view, imaging optical flows may distort and deviate seriously when they perform large angle attitude maneuvering imaging. The phenomena are mainly attributed to the geometrical characteristics of the three-dimensional earth surface as well as the coupled effects due to the complicated relative motion between the sensor and scene. Under this circumstance, velocity fields distribute nonlinearly, the imageries may badly be smeared or probably the geometrical structures are changed since the image velocity matching errors are not having been eliminated perfectly. In this paper, precise imaging optical flow model is established for agile remote sensors, for which optical flows evolving is factorized by two forms, which respectively due to translational movement and image shape changing. Moreover, base on that, agile remote sensors instrumentation was investigated. The main techniques which concern optical flow modeling include integrative design with lightweight star sensors along with micro inertial measurement units and corresponding data fusion, the assemblies of focal plane layout and control, imageries post processing for agile remote sensors etc. Some experiments show that the optical analyzing method is effective to

Controlling compositional homogeneity and crystalline orientation in Bi 0.8 Sb 0.2 thermoelectric thin films [Control of composition and crystallinity in Bi 0.8Sb 0.2 thermoelectric thin films].

DOE PAGES

Rochford, C.; Medlin, D. L.; Erickson, K. J.; ...

2015-12-01

Controlling alloy composition, crystalline quality, and crystal orientation is necessary to achieve high thermoelectric performance in Bi 1-xSb x thin films. These microstructural attributes are demonstrated in this letter via co-sputter deposition of Bi and Sb metals on Si/SiO 2 substrates followed by ex-situ post anneals ranging from 200 – 300 °C in forming gas with rapid cooling to achieve orientation along the trigonal axis. We show with cross-sectional transmission electron microscopy and energy-dispersive X-ray spectrometry that 50 – 95% of the Sb segregates at the surface upon exposure to air during transfer. This then forms a nanocrystalline Sb 2Omore » 3 layer upon annealing, leaving the bulk of the film primarily Bi metal which is a poor thermoelectric material. We demonstrate a SiN capping technique to eliminate Sb segregation and preserve a uniform composition throughout the thickness of the film. Given that the Bi 1-xSb x solid solution melting point depends on the Sb content, the SiN cap allows one to carefully approach but not exceed the melting point during annealing. This leads to the strong orientation along the trigonal axis and high crystalline quality desired for thermoelectric applications.« less

Installation Restoration Program Stage 2-1 Remedial Investigation. Beale Air Force Base, Marysville, California. Volume 2. Appendix A

DTIC Science & Technology

1991-03-29

S) A-927 BAFB-0427 22159-4 13-C-2SB (S) A-929 BAFB- 0428 22159-5 13-C-2SB (S) A-930 BAFB-0256 21872-11 13-C-2SB (S) A-931 BAFB-0429 22159-6 13-C-2SB (S...16 18-C-19SS (S) A-1305 BAFB-0021 21621-17 18-C-20SS (S) A- 1307 BAFB-0022 21621-18 18-C-20SS (S) A-1309 BAFB-0024 21621-20 18-C-21SS (S) A-1311 BAFB...ASA#9) 21.0 N/A MERCURY (SW7471) (Resampled for this analysis. See BAFB-0427 and BAFB- 0428 ) TFH-DIESEL (TFH-DIESEL) ə.3 1.3 mg/kg. (non-detect) TFH

Evaluation in Monkey of Two Candidate PET Radioligands, [11C]RX-1 and [18F]RX-2, for Imaging Brain 5-HT4 Receptors

PubMed Central

LOHITH, TALAKAD G.; XU, RONG; TSUJIKAWA, TETSUYA; MORSE, CHERYL L.; ANDERSON, KACEY B.; GLADDING, ROBERT L.; ZOGHBI, SAMI S.; FUJITA, MASAHIRO; INNIS, ROBERT B.; PIKE, VICTOR W.

2014-01-01

The serotonin subtype-4 (5-HT4) receptor, which is known to be involved physiologically in learning and memory, and pathologically in Alzheimer’s disease, anxiety and other neuropsychiatric disorders – has few radioligands readily available for imaging in vivo. We have previously reported two novel 5-HT4 receptor radioligands, namely [methoxy-11C](1-butylpiperidin-4-yl)methyl 4-amino-3-methoxybenzoate; [11C]RX-1) and the [18F]3-fluoromethoxy analog ([18F]RX-2), and in this study we evaluated them by PET in rhesus monkey. Brain scans were performed at baseline, receptor preblock or displacement conditions using SB 207710, a 5-HT4 receptor antagonist, on the same day for [11C]RX-1 and on different days for [18F]RX-2. Specific-to-nondisplaceable ratio (BPND) was measured with the simplified reference tissue model from all baseline scans. To determine specific binding, total distribution volume (VT) was also measured in some monkeys by radiometabolite-corrected arterial input function after ex vivo inhibition of esterases from baseline and blocked scans. Both radioligands showed moderate to high peak brain uptake of radioactivity (2–6 SUV). Regional BPND values were in the rank order of known 5-HT4 receptor distribution with a trend for higher BPND values from [18F]RX-2. One-tissue compartmental model provided good fits with well identified VT values for both radioligands. In the highest 5-HT4 receptor density region, striatum, 50–60% of total binding was specific. The VT in receptor-poor cerebellum reached stable values by about 60 min for both radioligands indicating little influence of radiometabolites on brain signal. In conclusion, both [11C]RX-1 and [18F]RX-2 showed positive attributes for PET imaging of brain 5-HT4 receptors, validating the radioligand design strategy. PMID:25088028

Treatment of air pollution control residues with iron rich waste sulfuric acid: does it work for antimony (Sb)?

PubMed

Okkenhaug, Gudny; Breedveld, Gijs D; Kirkeng, Terje; Lægreid, Marit; Mæhlum, Trond; Mulder, Jan

2013-03-15

Antimony (Sb) in air pollution control (APC) residues from municipal solid waste incineration has gained increased focus due to strict Sb leaching limits set by the EU landfill directive. Here we study the chemical speciation and solubility of Sb at the APC treatment facility NOAH Langøya (Norway), where iron (Fe)-rich sulfuric acid (∼3.6M, 2.3% Fe(II)), a waste product from the industrial extraction of ilmenite, is used for neutralization. Antimony in water extracts of untreated APC residues occurred exclusively as pentavalent antimonate, even at low pH and Eh values. The Sb solubility increased substantially at pH<10, possibly due to the dissolution of ettringite (at alkaline pH) or calcium (Ca)-antimonate. Treated APC residues, stored anoxically in the laboratory, simulating the conditions at the NOAH Langøya landfill, gave rise to decreasing concentrations of Sb in porewater, occurring exclusively as Sb(V). Concentrations of Sb decreased from 87-918μgL(-1) (day 3) to 18-69μgL(-1) (day 600). We hypothesize that an initial sorption of Sb to Fe(II)-Fe(III) hydroxides (green rust) and eventually precipitation of Ca- and Fe-antimonates (tripuhyite; FeSbO4) occurred. We conclude that Fe-rich, sulfuric acid waste is efficient to immobilize Sb in APC residues from waste incineration. Copyright © 2013 Elsevier B.V. All rights reserved.

Frequency Agile Microwave Photonic Notch Filter in a Photonic Chip

DTIC Science & Technology

2016-10-21

AFRL-AFOSR-JP-TR-2016-0087 Frequency Agile Microwave Photonic Notch Filter in a Photonic Chip Benjamin Eggleton UNIVERSITY OF SYDNEY Final Report 10...REPORT TYPE      Final 3.  DATES COVERED (From - To)      14 May 2014 to 13 May 2016 4.  TITLE AND SUBTITLE Frequency Agile Microwave Photonic Notch Filter ...primary objective is to explore a novel class microwave photonic (MWP) notch filter with a very narrow isolation bandwidth, an ultrahigh stopband

Spectral characterisation of aperiodic normal-incidence Sb/B4C multilayer mirrors for the λ < 124 Å range

NASA Astrophysics Data System (ADS)

Vishnyakov, E. A.; Kopylets, I. A.; Kondratenko, V. V.; Kolesnikov, A. O.; Pirozhkov, A. S.; Ragozin, E. N.; Shatokhin, A. N.

2018-03-01

Three broadband aperiodic Sb/B4C multilayer mirrors were synthesised for the purposes of soft X-ray optics and spectroscopy in the wavelength range beyond the L-edge of Si (λ < 124 Å), and their reflection spectra were measured. The multilayer structures were optimised for maximum uniform reflectivity in the ranges 100–120 Å, 95–105 Å and 90–100 Å. The reflection spectra were recorded using a laboratory laser-plasma radiation source and an electronic detector with a 2D spatial resolution (a CCD matrix with 13 × 13 μm sized pixels). The experimental spectra are compared with theoretical calculations. The effect of lower antimony and B4C layer densities on the reflection spectra is discussed.

A Literature Review on the Progression of Agile Manufacturing Paradigm and Its Scope of Application in Pump Industry

PubMed Central

Devadasan, S. R.; Sivaram, N. M.

2015-01-01

During the recent years, the manufacturing world has been witnessing the application of agile manufacturing paradigm. The literature review reported in this paper was carried out to study this progression. This literature review was carried out in two phases. In the first phase, the literature was reviewed to trace the origin of agile manufacturing paradigm and identify its enablers. Further, during this phase, the applications of agile manufacturing reported in literature arena were reviewed. It was also discernable that certain research works have been initiated to apply agile manufacturing paradigm in pump industry. During the second phase, the researches reported on applying agile manufacturing in pump industry were reviewed. At the end of this review, it was found that so far the implementation of agile manufacturing in pump industry has been examined by the researchers by considering only certain components of pumps. In fact, the holistic implementation of agile manufacturing in the pump industry is yet to be examined by the researchers. In the context of drawing this inference, this paper has been concluded by stating that high scope exists in examining the infusing of agility characteristics in designing and manufacturing of pumps. PMID:26065016

A Literature Review on the Progression of Agile Manufacturing Paradigm and Its Scope of Application in Pump Industry.

PubMed

Thilak, V M M; Devadasan, S R; Sivaram, N M