40 CFR 1065.125 - Engine intake air.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 34 2012-07-01 2012-07-01 false Engine intake air. 1065.125 Section... ENGINE-TESTING PROCEDURES Equipment Specifications § 1065.125 Engine intake air. (a) Use the intake-air system installed on the engine or one that represents a typical in-use configuration. This includes the...

40 CFR 1065.125 - Engine intake air.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 33 2014-07-01 2014-07-01 false Engine intake air. 1065.125 Section... ENGINE-TESTING PROCEDURES Equipment Specifications § 1065.125 Engine intake air. (a) Use the intake-air system installed on the engine or one that represents a typical in-use configuration. This includes the...

The two-stroke poppet valve engine. Part 1: Intake and exhaust ports flow experimental assessments

NASA Astrophysics Data System (ADS)

Kamili Zahidi, M.; Razali Hanipah, M.; Ramasamy, D.; Noor, M. M.; Kadirgama, K.; Rahman, M. M.

2017-10-01

A two-stroke poppet valve engine is developed to overcome the common problems in conventional two-stroke engine designs. However, replacing piston control port with poppet valve will resulted different flow behaviour. This paper is looking at experimental assessment on a two-stroke poppet valve engine configuration to investigate the port flow performance. The aims are to evaluate the intake and exhaust coefficient of discharge and assess the twostroke capability of the cylinder head. The results has shown comparable coefficient of discharge values as production engine for the intake while the exhaust has higher values which is favourable for the two-stroke cycle operation.

40 CFR 89.326 - Engine intake air humidity measurement.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Engine intake air humidity measurement... Test Equipment Provisions § 89.326 Engine intake air humidity measurement. (a) Humidity conditioned air... type of intake air supply, the humidity measurements must be made within the intake air supply system...

C-PORT: A Community-Scale Near-Source Air Quality System to Assess Port-Related Air Quality Impacts

EPA Science Inventory

With increasing activity in global trade, there has been increased activity in transportation by rail, road and ships to move cargo. Based upon multiple near-road and near-source monitoring studies, both busy roadways and large emission source at the ports may impact local air qu...

A Community-Scale Modeling System to Assess Port-Related Air Quality Impacts

EPA Science Inventory

Near-port air pollution has been identified by numerous organizations as a potential public health concern. Based upon multiple near-road and near-source monitoring studies, both busy roadways and large emission sources at the ports may impact local air quality within several hun...

30 CFR 250.510 - Diesel engine air intakes.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 2 2011-07-01 2011-07-01 false Diesel engine air intakes. 250.510 Section 250.510 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, REGULATION, AND ENFORCEMENT, DEPARTMENT OF... Well-Completion Operations § 250.510 Diesel engine air intakes. Diesel engine air intakes must be...

30 CFR 250.610 - Diesel engine air intakes.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 2 2013-07-01 2013-07-01 false Diesel engine air intakes. 250.610 Section 250.610 Mineral Resources BUREAU OF SAFETY AND ENVIRONMENTAL ENFORCEMENT, DEPARTMENT OF THE INTERIOR... Operations § 250.610 Diesel engine air intakes. No later than May 31, 1989, diesel engine air intakes shall...

30 CFR 250.510 - Diesel engine air intakes.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 2 2013-07-01 2013-07-01 false Diesel engine air intakes. 250.510 Section 250.510 Mineral Resources BUREAU OF SAFETY AND ENVIRONMENTAL ENFORCEMENT, DEPARTMENT OF THE INTERIOR... Operations § 250.510 Diesel engine air intakes. Diesel engine air intakes must be equipped with a device to...

30 CFR 250.510 - Diesel engine air intakes.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 2 2012-07-01 2012-07-01 false Diesel engine air intakes. 250.510 Section 250.510 Mineral Resources BUREAU OF SAFETY AND ENVIRONMENTAL ENFORCEMENT, DEPARTMENT OF THE INTERIOR... Operations § 250.510 Diesel engine air intakes. Diesel engine air intakes must be equipped with a device to...

30 CFR 250.510 - Diesel engine air intakes.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 2 2014-07-01 2014-07-01 false Diesel engine air intakes. 250.510 Section 250.510 Mineral Resources BUREAU OF SAFETY AND ENVIRONMENTAL ENFORCEMENT, DEPARTMENT OF THE INTERIOR... Operations § 250.510 Diesel engine air intakes. Diesel engine air intakes must be equipped with a device to...

30 CFR 250.610 - Diesel engine air intakes.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Diesel engine air intakes. 250.610 Section 250.610 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND... engine air intakes. No later than May 31, 1989, diesel engine air intakes shall be equipped with a device...

30 CFR 250.510 - Diesel engine air intakes.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Diesel engine air intakes. 250.510 Section 250.510 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND... engine air intakes. Diesel engine air intakes must be equipped with a device to shut down the diesel...

National Port Strategy Assessment: Reducing Air Pollution and Greenhouse Gases at U.S. Ports

EPA Pesticide Factsheets

The assessment finds that air pollution at the Nation's ports can be significantly reduced by implementing currently available strategies and technologies to reduce emissions of harmful pollutants from diesel vehicles and engines.

40 CFR 89.325 - Engine intake air temperature measurement.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Engine intake air temperature measurement. 89.325 Section 89.325 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Test Equipment Provisions § 89.325 Engine intake air temperature measurement. (a) Engine intake air...

A web-based screening tool for near-port air quality assessments

PubMed Central

Isakov, Vlad; Barzyk, Timothy M.; Smith, Elizabeth R.; Arunachalam, Saravanan; Naess, Brian; Venkatram, Akula

2018-01-01

The Community model for near-PORT applications (C-PORT) is a screening tool with an intended purpose of calculating differences in annual averaged concentration patterns and relative contributions of various source categories over the spatial domain within about 10 km of the port. C-PORT can inform decision-makers and concerned citizens about local air quality due to mobile source emissions related to commercial port activities. It allows users to visualize and evaluate different planning scenarios, helping them identify the best alternatives for making long-term decisions that protect community health and sustainability. The web-based, easy-to-use interface currently includes data from 21 seaports primarily in the Southeastern U.S., and has a map-based interface based on Google Maps. The tool was developed to visualize and assess changes in air quality due to changes in emissions and/or meteorology in order to analyze development scenarios, and is not intended to support or replace any regulatory models or programs. PMID:29681760

30 CFR 250.610 - Diesel engine air intakes.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 2 2011-07-01 2011-07-01 false Diesel engine air intakes. 250.610 Section 250... Well-Workover Operations § 250.610 Diesel engine air intakes. No later than May 31, 1989, diesel engine air intakes shall be equipped with a device to shut down the diesel engine in the event of runaway...

30 CFR 250.610 - Diesel engine air intakes.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 2 2012-07-01 2012-07-01 false Diesel engine air intakes. 250.610 Section 250... Operations § 250.610 Diesel engine air intakes. No later than May 31, 1989, diesel engine air intakes shall be equipped with a device to shut down the diesel engine in the event of runaway. Diesel engines...

30 CFR 250.610 - Diesel engine air intakes.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 2 2014-07-01 2014-07-01 false Diesel engine air intakes. 250.610 Section 250... Operations § 250.610 Diesel engine air intakes. No later than May 31, 1989, diesel engine air intakes shall be equipped with a device to shut down the diesel engine in the event of runaway. Diesel engines...

40 CFR 1065.225 - Intake-air flow meter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... flow meter. (a) Application. You may use an intake-air flow meter in combination with a chemical..., you may use an intake-air flow meter signal that does not give the actual value of raw exhaust, as... requirements. We recommend that you use an intake-air flow meter that meets the specifications in Table 1 of...

40 CFR 91.309 - Engine intake air temperature measurement.

Code of Federal Regulations, 2010 CFR

2010-07-01

... measurement. 91.309 Section 91.309 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Provisions § 91.309 Engine intake air temperature measurement. (a) Engine intake air temperature measurement must be made within 100 cm of the air-intake of the engine. The measurement location must be either in...

40 CFR 92.108 - Intake and cooling air measurements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Intake and cooling air measurements....108 Intake and cooling air measurements. (a) Intake air flow measurement. Measurement of the flow rate..., the measurement technique shall conform to the following: (1) The air flow measurement method used...

40 CFR 91.309 - Engine intake air temperature measurement.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 20 2014-07-01 2013-07-01 true Engine intake air temperature... Provisions § 91.309 Engine intake air temperature measurement. (a) Engine intake air temperature measurement... the supply system or in the air stream entering the engine. (b) The temperature measurements must be...

40 CFR 91.309 - Engine intake air temperature measurement.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 21 2012-07-01 2012-07-01 false Engine intake air temperature... Provisions § 91.309 Engine intake air temperature measurement. (a) Engine intake air temperature measurement... the supply system or in the air stream entering the engine. (b) The temperature measurements must be...

40 CFR 91.309 - Engine intake air temperature measurement.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 21 2013-07-01 2013-07-01 false Engine intake air temperature... Provisions § 91.309 Engine intake air temperature measurement. (a) Engine intake air temperature measurement... the supply system or in the air stream entering the engine. (b) The temperature measurements must be...

40 CFR 91.309 - Engine intake air temperature measurement.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 20 2011-07-01 2011-07-01 false Engine intake air temperature... Provisions § 91.309 Engine intake air temperature measurement. (a) Engine intake air temperature measurement... the supply system or in the air stream entering the engine. (b) The temperature measurements must be...

40 CFR 91.416 - Intake air flow measurement specifications.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Intake air flow measurement... Procedures § 91.416 Intake air flow measurement specifications. (a) If used, the engine intake air flow measurement method used must have a range large enough to accurately measure the air flow over the engine...

The influence of mixture preparation in the intake port on the performance of a spark-ignited four-stroke engine

NASA Astrophysics Data System (ADS)

Daniels, Charles Howard

An experimental technique is developed for evaluating the influence of mixture preparation in the intake port on the performance of a spark ignited engine. The preparation components studied are fuel vapor, droplets, and liquid streams. The fuel in these three distinct forms are produced and varied in a specially designed mixture preparation system, which delivers an air/fuel mixture to a test cylinder of an engine. Incorporated in the preparation system are devices for measuring the flow rates of fuel in these forms. A method of estimating the vapor concentration of a gasoline in the preparation channel by the use of simple temperature measurements is also presented. The effect of these fuel forms on in-cylinder pressure performance and exhaust gas concentrations are investigated in a 1.9 L Ford engine. A matrix of engine operations are studied along with two gasolines of different volatilities. The results of this investigation show that the operation of the engine at low speeds and low manifold absolute pressures is most susceptible to the effects mixture preparation. For those engine operating conditions affected, the results show that by increasing the amount of fuel in liquid stream form, the performance of the engine is generally diminished. In addition, 'equivalent' mixtures resulting from a conventional injector and a pneumatic atomizer in the intake port are identified relative to engine performance.

40 CFR 90.310 - Engine intake air humidity measurement.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Engine intake air humidity measurement... Emission Test Equipment Provisions § 90.310 Engine intake air humidity measurement. This section refers to... for the engine intake air, the ambient test cell humidity measurement may be used. (a) Humidity...

40 CFR 90.416 - Intake air flow measurement specifications.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Intake air flow measurement... Gaseous Exhaust Test Procedures § 90.416 Intake air flow measurement specifications. (a) If used, the engine intake air flow measurement method used must have a range large enough to accurately measure the...

40 CFR 89.325 - Engine intake air temperature measurement.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 21 2013-07-01 2013-07-01 false Engine intake air temperature... Test Equipment Provisions § 89.325 Engine intake air temperature measurement. (a) Engine intake air temperature measurement must be made within 122 cm of the engine. The measurement location must be made either...

40 CFR 89.325 - Engine intake air temperature measurement.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 20 2011-07-01 2011-07-01 false Engine intake air temperature... Test Equipment Provisions § 89.325 Engine intake air temperature measurement. (a) Engine intake air temperature measurement must be made within 122 cm of the engine. The measurement location must be made either...

40 CFR 89.325 - Engine intake air temperature measurement.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 20 2014-07-01 2013-07-01 true Engine intake air temperature... Test Equipment Provisions § 89.325 Engine intake air temperature measurement. (a) Engine intake air temperature measurement must be made within 122 cm of the engine. The measurement location must be made either...

40 CFR 89.325 - Engine intake air temperature measurement.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 21 2012-07-01 2012-07-01 false Engine intake air temperature... Test Equipment Provisions § 89.325 Engine intake air temperature measurement. (a) Engine intake air temperature measurement must be made within 122 cm of the engine. The measurement location must be made either...

40 CFR 1065.225 - Intake-air flow meter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 33 2014-07-01 2014-07-01 false Intake-air flow meter. 1065.225 Section 1065.225 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS ENGINE-TESTING PROCEDURES Measurement Instruments Flow-Related Measurements § 1065.225 Intake-air...

40 CFR 1065.225 - Intake-air flow meter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 34 2013-07-01 2013-07-01 false Intake-air flow meter. 1065.225 Section 1065.225 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS ENGINE-TESTING PROCEDURES Measurement Instruments Flow-Related Measurements § 1065.225 Intake-air...

40 CFR 1065.225 - Intake-air flow meter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 33 2011-07-01 2011-07-01 false Intake-air flow meter. 1065.225 Section 1065.225 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS ENGINE-TESTING PROCEDURES Measurement Instruments Flow-Related Measurements § 1065.225 Intake-air...

Measurement and Modeling of Near Road & Near-Port Air Quality

EPA Science Inventory

Air pollution from mobile sources has been identified by numerous organizations as a potential public health concern. Based upon multiple near-road and near-source monitoring studies, both busy roadways and large emission sources at ports can significantly impact local air qualit...

40 CFR 91.310 - Engine intake air humidity measurement.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Engine intake air humidity measurement... Provisions § 91.310 Engine intake air humidity measurement. This section refers to engines which are supplied... air, the ambient testcell humidity measurement may be used. (a) Humidity conditioned air supply. Air...

28. Main engine air pump located to port side of ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

28. Main engine air pump located to port side of main engine cylinder beside engine bed. Dynamo lies aft of air pump (at right), pipe at extreme left of image carries lake water to condenser valves. - Steamboat TICONDEROGA, Shelburne Museum Route 7, Shelburne, Chittenden County, VT

Report: EPA Needs to Improve Its Efforts to Reduce Air Emissions at U.S. Ports

EPA Pesticide Factsheets

Report #09-P-0125, March 23, 2009. While EPA has issued air emissions regulations for most port sources, EPA’s actions to address air emissions from large oceangoing vessels in U.S. ports have not yet achieved the goals for protecting human health.

40 CFR 90.309 - Engine intake air temperature measurement.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Engine intake air temperature measurement. 90.309 Section 90.309 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Emission Test Equipment Provisions § 90.309 Engine intake air temperature measurement. (a) The measurement...

48 CFR 47.305-6 - Shipments to ports and air terminals.

Code of Federal Regulations, 2010 CFR

2010-10-01

... subpart 47.5—Ocean Transportation by U.S.-Flag Vessels.) (k) For application of the Fly America Act to the... subpart 47.4—Air Transportation by U.S.-Flag Carriers. (l) Military and civilian agencies shall obtain... information: (1) When the delivery term is f.a.s. vessel, port of shipment, f.o.b. vessel, port of shipment...

48 CFR 47.305-6 - Shipments to ports and air terminals.

Code of Federal Regulations, 2014 CFR

2014-10-01

... subpart 47.5—Ocean Transportation by U.S.-Flag Vessels.) (k) For application of the Fly America Act to the... subpart 47.4—Air Transportation by U.S.-Flag Carriers. (l) Military and civilian agencies shall obtain... information: (1) When the delivery term is f.a.s. vessel, port of shipment, f.o.b. vessel, port of shipment...

48 CFR 47.305-6 - Shipments to ports and air terminals.

Code of Federal Regulations, 2011 CFR

2011-10-01

... subpart 47.5—Ocean Transportation by U.S.-Flag Vessels.) (k) For application of the Fly America Act to the... subpart 47.4—Air Transportation by U.S.-Flag Carriers. (l) Military and civilian agencies shall obtain... information: (1) When the delivery term is f.a.s. vessel, port of shipment, f.o.b. vessel, port of shipment...

48 CFR 47.305-6 - Shipments to ports and air terminals.

Code of Federal Regulations, 2013 CFR

2013-10-01

... subpart 47.5—Ocean Transportation by U.S.-Flag Vessels.) (k) For application of the Fly America Act to the... subpart 47.4—Air Transportation by U.S.-Flag Carriers. (l) Military and civilian agencies shall obtain... information: (1) When the delivery term is f.a.s. vessel, port of shipment, f.o.b. vessel, port of shipment...

48 CFR 47.305-6 - Shipments to ports and air terminals.

Code of Federal Regulations, 2012 CFR

2012-10-01

... subpart 47.5—Ocean Transportation by U.S.-Flag Vessels.) (k) For application of the Fly America Act to the... subpart 47.4—Air Transportation by U.S.-Flag Carriers. (l) Military and civilian agencies shall obtain... information: (1) When the delivery term is f.a.s. vessel, port of shipment, f.o.b. vessel, port of shipment...

Method and apparatus for extracting water from air

DOEpatents

Spletzer, Barry L.; Callow, Diane Schafer; Marron, Lisa C.; Salton, Jonathan R.

2002-01-01

The present invention provides a method and apparatus for extracting liquid water from moist air using minimal energy input. The method comprises compressing moist air under conditions that foster the condensation of liquid water. The air can be decompressed under conditions that do not foster the vaporization of the condensate. The decompressed, dried air can be exchanged for a fresh charge of moist air and the process repeated. The liquid condensate can be removed for use. The apparatus can comprise a compression chamber having a variable internal volume. An intake port allows moist air into the compression chamber. An exhaust port allows dried air out of the compression chamber. A condensation device fosters condensation at the desired conditions. A condensate removal port allows liquid water to be removed.

40 CFR 90.309 - Engine intake air temperature measurement.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 21 2013-07-01 2013-07-01 false Engine intake air temperature... Emission Test Equipment Provisions § 90.309 Engine intake air temperature measurement. (a) The measurement...) The temperature measurements must be accurate to within ±2 °C. ...

40 CFR 90.309 - Engine intake air temperature measurement.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 20 2014-07-01 2013-07-01 true Engine intake air temperature... Emission Test Equipment Provisions § 90.309 Engine intake air temperature measurement. (a) The measurement...) The temperature measurements must be accurate to within ±2 °C. ...

40 CFR 90.309 - Engine intake air temperature measurement.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 20 2011-07-01 2011-07-01 false Engine intake air temperature... Emission Test Equipment Provisions § 90.309 Engine intake air temperature measurement. (a) The measurement...) The temperature measurements must be accurate to within ±2 °C. ...

40 CFR 90.309 - Engine intake air temperature measurement.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 21 2012-07-01 2012-07-01 false Engine intake air temperature... Emission Test Equipment Provisions § 90.309 Engine intake air temperature measurement. (a) The measurement...) The temperature measurements must be accurate to within ±2 °C. ...

30 CFR 75.341 - Direct-fired intake air heaters.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 75.341 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.341 Direct-fired intake air heaters. (a) If any system used to heat intake air malfunctions, the heaters affected shall switch...

Method and apparatus for extracting water from air

DOEpatents

Spletzer, Barry L.

2001-01-01

The present invention provides a method and apparatus for extracting liquid water from moist air using minimal energy input. The method comprises compressing moist air under conditions that foster the condensation of liquid water (ideally isothermal to a humidity of 1.0, then adiabatic thereafter). The air can be decompressed under conditions that do not foster the vaporization of the condensate. The decompressed, dried air can be exchanged for a fresh charge of moist air and the process repeated. The liquid condensate can be removed for use. The apparatus can comprise a compression chamber having a variable internal volume. An intake port allows moist air into the compression chamber. An exhaust port allows dried air out of the compression chamber. A condensation device fosters condensation at the desired conditions. A condensate removal port allows liquid water to be removed.

LCD OF AIR INTAKE MANIFOLDS PHASE 2: FORD F250 AIR INTAKE MANIFOLD

EPA Science Inventory

The life cycle design methodology was applied to the design analysis of three alternatives for the lower plehum of the air intake manifold for us with a 5.4L F-250 truck engine: a sand cast aluminum, a lost core molded nylon composite, and a vibration welded nylon composite. The ...

Investigating performance of microchannel evaporators for automobile air conditioning with different port structures

NASA Astrophysics Data System (ADS)

Zhou, Guoliang; Su, Lin; Cheng, Qia; Wu, Longbing

2017-08-01

Microchannel evaporator has been widely applied in automobile air conditioning, while it faces the problem of refrigerant maldistribution which deteriorates the thermal performance of evaporator. In this study, the performances of microchannel evaporators with different port structures are experimentally investigated for purpose of reducing evaporator pressure drop. Four evaporator samples with different port number and hydraulic diameter are made for this study. The performances of the evaporator samples are tested on a psychometric calorimeter test bench with the refrigerant R-134A at a real automobile air conditioning. The results on the variations of the evaporator pressure drop and evaporator surface temperature distribution are presented and analyzed. By studying the performance of an evaporator, seeking proper port structure is an approach to reduce refrigerant pressure drop as well as improve refrigerant distribution.

Community Near-Port Modeling System (C-PORT): Briefing for ...

EPA Pesticide Factsheets

What C-PORT is: Screening level tool for assessing port activities and exploring the range of potential impacts that changes to port operations might have on local air quality; Analysis of decision alternatives through mapping of the likely pattern of potential pollutant dispersion and an estimated change in pollutant concentrations for user-designated scenarios; Designed primarily to evaluate the local air quality impacts of proposed port expansion or modernization, as well as to identify options for mitigating any impacts; Currently includes data from 21 US seaports and features a map-based interface similar to the widely used Google Earth; Still under development, C-PORT is designed as an easy-to-use computer modeling tool for users, such as state air quality managers and planners. This is part of our product outreach prior to model public release and to solicit for additional beta testers.

Port Stakeholder Summit: Advancing More Sustainable Ports (April 2014)

EPA Pesticide Factsheets

EPA's National Port Stakeholders Summit, Advancing More Sustainable Ports, focused on actions to protect air quality while reducing climate risk and supporting economic growth, making ports more environmentally sustainable.

Ports Primer: 7.4 Agency Responsibilities

EPA Pesticide Factsheets

Near-port communities are often disproportionately impacted by air emissions due to port operations, goods movement operations and other industries that may be co-located with ports. Air emissions at ports also impact regional air quality.

Promoting Port Stakeholder Success: Collaborative Action with EPA — Focus on Transportation & Air Quality (September 2013 Webinar)

EPA Pesticide Factsheets

To exchange views and develop a shared understanding of the challenges and opportunities of ports and port communities, EPA's Office of Transportation and Air Quality is hosting a series of webinars, bringing together port stakeholders.

Ports Initiative

EPA Pesticide Factsheets

EPA's Ports Initiative works in collaboration with the port industry, communities, and government to improve environmental performance and increase economic prosperity. This effort helps people near ports breath cleaner air and live better lives.

Air intake side secondary air supply system for an internal combustion engine with a duty ratio control operation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kawanabe, T.; Asakura, M.; Shina, T.

1987-09-01

An air intake side secondary air supply system is described for an internal combustion engine having an air intake passage with a carburetor and an exhaust passage, comprising: an air intake side secondary air supply passage communicating with the air intake passage on the downstream side of the carburetor; an open/close valve disposed in the air intake side secondary air supply passage; an oxygen concentration sensor disposed in the exhaust passage; and detection and control means for detecting whether an air-fuel ratio of mixture to be supplied to the engine is leaner or richer with respect to a target air-fuelmore » ratio through a level of an output signal of the oxygen concentration sensor and for periodically actuating the open/close valve, the detection and control means decreasing a valve open period of the open/close valve within each cyclic period by a first predetermined amount when a detected air-fuel ratio of mixture is leaner than the target air-fuel ratio and increasing the valve open period by a second predetermined amount when the detected air-fuel ratio of mixture is richer than the target air-fuel ratio. The second predetermined amount is different from the first predetermined amount.« less

40 CFR 1065.655 - Chemical balances of fuel, intake air, and exhaust.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 33 2014-07-01 2014-07-01 false Chemical balances of fuel, intake air... Chemical balances of fuel, intake air, and exhaust. (a) General. Chemical balances of fuel, intake air, and... balances to determine the flows of the other two. For example, you may use chemical balances along with...

40 CFR 1065.655 - Chemical balances of fuel, intake air, and exhaust.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 34 2012-07-01 2012-07-01 false Chemical balances of fuel, intake air... Chemical balances of fuel, intake air, and exhaust. (a) General. Chemical balances of fuel, intake air, and... balances to determine the flows of the other two. For example, you may use chemical balances along with...

40 CFR 1065.655 - Chemical balances of fuel, intake air, and exhaust.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 34 2013-07-01 2013-07-01 false Chemical balances of fuel, intake air... Chemical balances of fuel, intake air, and exhaust. (a) General. Chemical balances of fuel, intake air, and... balances to determine the flows of the other two. For example, you may use chemical balances along with...

40 CFR 1065.655 - Chemical balances of fuel, intake air, and exhaust.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 33 2011-07-01 2011-07-01 false Chemical balances of fuel, intake air... Chemical balances of fuel, intake air, and exhaust. (a) General. Chemical balances of fuel, intake air, and... balances to determine the flows of the other two. For example, you may use chemical balances along with...

40 CFR 1065.655 - Chemical balances of fuel, intake air, and exhaust.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Chemical balances of fuel, intake air... Chemical balances of fuel, intake air, and exhaust. (a) General. Chemical balances of fuel, intake air, and... balances to determine the flows of the other two. For example, you may use chemical balances along with...

System and method for conditioning intake air to an internal combustion engine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sellnau, Mark C.

A system for conditioning the intake air to an internal combustion engine includes a means to boost the pressure of the intake air to the engine and a liquid cooled charge air cooler disposed between the output of the boost means and the charge air intake of the engine. Valves in the coolant system can be actuated so as to define a first configuration in which engine cooling is performed by coolant circulating in a first coolant loop at one temperature, and charge air cooling is performed by coolant flowing in a second coolant loop at a lower temperature. Themore » valves can be actuated so as to define a second configuration in which coolant that has flowed through the engine can be routed through the charge air cooler. The temperature of intake air to the engine can be controlled over a wide range of engine operation.« less

Variable oxygen/nitrogen enriched intake air system for internal combustion engine applications

DOEpatents

Poola, Ramesh B.; Sekar, Ramanujam R.; Cole, Roger L.

1997-01-01

An air supply control system for selectively supplying ambient air, oxygen enriched air and nitrogen enriched air to an intake of an internal combustion engine includes an air mixing chamber that is in fluid communication with the air intake. At least a portion of the ambient air flowing to the mixing chamber is selectively diverted through a secondary path that includes a selectively permeable air separating membrane device due a differential pressure established across the air separating membrane. The permeable membrane device separates a portion of the nitrogen in the ambient air so that oxygen enriched air (permeate) and nitrogen enriched air (retentate) are produced. The oxygen enriched air and the nitrogen enriched air can be selectively supplied to the mixing chamber or expelled to atmosphere. Alternatively, a portion of the nitrogen enriched air can be supplied through another control valve to a monatomic-nitrogen plasma generator device so that atomic nitrogen produced from the nitrogen enriched air can be then injected into the exhaust of the engine. The oxygen enriched air or the nitrogen enriched air becomes mixed with the ambient air in the mixing chamber and then the mixed air is supplied to the intake of the engine. As a result, the air being supplied to the intake of the engine can be regulated with respect to the concentration of oxygen and/or nitrogen.

Fuel-air mixing and combustion in a two-dimensional Wankel engine

NASA Technical Reports Server (NTRS)

Shih, T. I.-P.; Schock, H. J.; Ramos, J. I.

1987-01-01

A two-equation turbulence model, an algebraic grid generalization method, and an approximate factorization time-linearized numerical technique are used to study the effects of mixture stratification at the intake port and gaseous fuel injection on the flow field and fuel-air mixing in a two-dimensional rotary engine model. The fuel distribution in the combustion chamber is found to be a function of the air-fuel mixture fluctuations at the intake port. It is shown that the fuel is advected by the flow field induced by the rotor and is concentrated near the leading apex during the intake stroke, while during compression, the fuel concentration is highest near the trailing apex and is lowest near the rotor. It is also found that the fuel concentration near the trailing apex and rotor is small except at high injection velocities.

Assessment of port-related air quality impacts: geographic analysis of population

EPA Science Inventory

Increased global trade has led to greater transportation by rail, road and ships to move cargo. Based upon multiple near-road and near-source monitoring studies, the busy roadways and large emission sources at ports may impact local air quality within several hundred metres of th...

LIFE CYCLE DESIGN OF AIR INTAKE MANIFOLDS; PHASE I: 2.0 L FORD CONTOUR AIR INTAKE MANIFOLD

EPA Science Inventory

The project team applied the life cycle design methodology to the design analysis of three alternative air intake manifolds: a sand cast aluminum, brazed aluminum tubular, and nylon composite. The design analysis included a life cycle inventory analysis, environmental regulatory...

Air quality impact assessment of at-berth ship emissions: Case-study for the project of a new freight port.

PubMed

Lonati, Giovanni; Cernuschi, Stefano; Sidi, Shelina

2010-12-01

This work is intended to assess the impact on local air quality due to atmospheric emissions from port area activities for a new port in project in the Mediterranean Sea. The sources of air pollutants in the harbour area are auxiliary engines used by ships at berth during loading/offloading operations. A fleet activity-based methodology is first applied to evaluate annual pollutant emissions (NO(X), SO(X), PM, CO and VOC) based on vessel traffic data, ships tonnage and in-port hotelling time for loading/offloading operations. The 3-dimensional Calpuff transport and dispersion model is then applied for the subsequent assessment of the ground level spatial distribution of atmospheric pollutants for both long-term and short-term averaging times. Compliance with current air quality standards in the port area is finally evaluated and indications for port operation are provided. Some methodological aspects of the impact assessment procedure, namely those concerning the steps of emission scenario definitions and model simulations set-up at the project stage, are specifically addressed, suggesting a pragmatic approach for similar evaluations for small new ports in project. Copyright © 2010 Elsevier B.V. All rights reserved.

Air Traffic Forecasting at the Port Authority of New York and New Jersey

NASA Technical Reports Server (NTRS)

Augustine, J. G.

1972-01-01

Procedures for conducting air traffic forecasts with specific application to the Port Authority of New York and New Jersey are discussed. The procedure relates air travel growth to detailed socio-economic and demographic characteristics of the U.S. population rather than to aggregate economic data such as Gross National Product, personal income, and industrial production. Charts are presented to show the relationship between various selected characteristics and the use of air transportation facilities.

An Ejector Air Intake Design Method for a Novel Rocket-Based Combined-Cycle Rocket Nozzle

NASA Astrophysics Data System (ADS)

Waung, Timothy S.

Rocket-based combined-cycle (RBCC) vehicles have the potential to reduce launch costs through the use of several different air breathing engine cycles, which reduce fuel consumption. The rocket-ejector cycle, in which air is entrained into an ejector section by the rocket exhaust, is used at flight speeds below Mach 2. This thesis develops a design method for an air intake geometry around a novel RBCC rocket nozzle design for the rocket-ejector engine cycle. This design method consists of a geometry creation step in which a three-dimensional intake geometry is generated, and a simple flow analysis step which predicts the air intake mass flow rate. The air intake geometry is created using the rocket nozzle geometry and eight primary input parameters. The input parameters are selected to give the user significant control over the air intake shape. The flow analysis step uses an inviscid panel method and an integral boundary layer method to estimate the air mass flow rate through the intake geometry. Intake mass flow rate is used as a performance metric since it directly affects the amount of thrust a rocket-ejector can produce. The design method results for the air intake operating at several different points along the subsonic portion of the Ariane 4 flight profile are found to under predict mass flow rate by up to 8.6% when compared to three-dimensional computational fluid dynamics simulations for the same air intake.

Ships, ports and particulate air pollution - an analysis of recent studies

PubMed Central

2011-01-01

The duration of use is usually significantly longer for marine vessels than for roadside vehicles. Therefore, these vessels are often powered by relatively old engines which may propagate air pollution. Also, the quality of fuel used for marine vessels is usually not comparable to the quality of fuels used in the automotive sector and therefore, port areas may exhibit a high degree of air pollution. In contrast to the multitude of studies that addressed outdoor air pollution due to road traffic, only little is known about ship-related air pollution. Therefore the present article aims to summarize recent studies that address air pollution, i.e. particulate matter exposure, due to marine vessels. It can be stated that the data in this area of research is still largely limited. Especially, knowledge on the different air pollutions in different sea areas is needed. PMID:22141925

Method and apparatus for reducing cold-phase emissions by utilizing oxygen-enriched intake air

DOEpatents

Poola, Ramesh B.; Sekar, Ramanujam R.; Stork, Kevin C.

1997-01-01

An oxygen-enriched air intake control system for an internal combustion engine includes air directing apparatus to control the air flow into the intake of the engine. During normal operation of the engine, ambient air flowing from an air filter of the engine flows through the air directing apparatus into the intake of the engine. In order to decrease the amount of carbon monoxide (CO) and hydrocarbon (HC) emissions that tend to be produced by the engine during a short period of time after the engine is started, the air directing apparatus diverts for a short period of time following the start up of the engine at least a portion of the ambient air from the air filter through a secondary path. The secondary path includes a selectively permeable membrane through which the diverted portion of the ambient air flows. The selectively permeable membrane separates nitrogen and oxygen from the diverted air so that oxygen enriched air containing from about 23% to 25% oxygen by volume is supplied to the intake of the engine.

Engine Air Intake Manifold Having Built In Intercooler

DOEpatents

Freese, V, Charles E.

2000-09-12

A turbocharged V type engine can be equipped with an exhaust gas recirculation cooler integrated into the intake manifold, so as to achieve efficiency, cost reductions and space economization improvements. The cooler can take the form of a tube-shell heat exchanger that utilizes a cylindrical chamber in the air intake manifold as the heat exchanger housing. The intake manifold depends into the central space formed by the two banks of cylinders on the V type engine, such that the central space is effectively utilized for containing the manifold and cooler.

Community Near-Port Modeling System (C-PORT): Briefing for Environmental Defense Fund

EPA Science Inventory

What C-PORT is: Screening level tool for assessing port activities and exploring the range of potential impacts that changes to port operations might have on local air quality; Analysis of decision alternatives through mapping of the likely pattern of potential pollutant dispersi...

Working characteristics of variable intake valve in compressed air engine.

PubMed

Yu, Qihui; Shi, Yan; Cai, Maolin

2014-01-01

A new camless compressed air engine is proposed, which can make the compressed air energy reasonably distributed. Through analysis of the camless compressed air engine, a mathematical model of the working processes was set up. Using the software MATLAB/Simulink for simulation, the pressure, temperature, and air mass of the cylinder were obtained. In order to verify the accuracy of the mathematical model, the experiments were conducted. Moreover, performance analysis was introduced to design compressed air engine. Results show that, firstly, the simulation results have good consistency with the experimental results. Secondly, under different intake pressures, the highest output power is obtained when the crank speed reaches 500 rpm, which also provides the maximum output torque. Finally, higher energy utilization efficiency can be obtained at the lower speed, intake pressure, and valve duration angle. This research can refer to the design of the camless valve of compressed air engine.

Port Stakeholder Summit - April 2014

EPA Pesticide Factsheets

EPA's National Port Stakeholders Summit, Advancing More Sustainable Ports, focused on actions to protect air quality while reducing climate risk and supporting economic growth, making ports more environmentally sustainable.

Ports Primer: 7.3 Federal Environmental Regulations, Initiatives and Standards

EPA Pesticide Factsheets

Near-port communities are often disproportionately impacted by air emissions due to port operations, goods movement operations and other industries that may be co-located with ports. Air emissions at ports also impact regional air quality.

Working Characteristics of Variable Intake Valve in Compressed Air Engine

PubMed Central

Yu, Qihui; Shi, Yan; Cai, Maolin

2014-01-01

A new camless compressed air engine is proposed, which can make the compressed air energy reasonably distributed. Through analysis of the camless compressed air engine, a mathematical model of the working processes was set up. Using the software MATLAB/Simulink for simulation, the pressure, temperature, and air mass of the cylinder were obtained. In order to verify the accuracy of the mathematical model, the experiments were conducted. Moreover, performance analysis was introduced to design compressed air engine. Results show that, firstly, the simulation results have good consistency with the experimental results. Secondly, under different intake pressures, the highest output power is obtained when the crank speed reaches 500 rpm, which also provides the maximum output torque. Finally, higher energy utilization efficiency can be obtained at the lower speed, intake pressure, and valve duration angle. This research can refer to the design of the camless valve of compressed air engine. PMID:25379536

40 CFR 1065.225 - Intake-air flow meter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... concentrations, if the same signal is used in a chemical-balance calculation to determine work from brake... tube, or a hot-wire anemometer. Note that your overall system for measuring intake-air flow must meet...

Air intakes for a probative missile of rocket ramjet

NASA Technical Reports Server (NTRS)

Laruelle, G.

1984-01-01

The methods employed to test air intakes for a supersonic guided ramjet powered missile being tested by ONERA are described. Both flight tests and wind tunnel tests were performed on instrumented rockets to verify the designs. Consideration as given to the number of intakes, with the goal of delivering the maximum pressure to the engine. The S2, S4, and S5 wind tunnels were operated at Mach nos. 1.5-3 for the tests, which were compartmentalized into fuselage-intake interaction, optimization of the intake shapes, and the intake performance. Tests were performed on the length and form of the ogive, the presence of grooves, the height of traps in the boundary layer, the types and number of intakes and the lengths and forms of diffusers. Attention was also given to the effects of sideslip, effects of the longitudinal and circumferential positions of the intakes were also examined. Near optimum performance was realized during Mach 2.2 test flights of the prototype rockets.

30 CFR 75.341 - Direct-fired intake air heaters.

Code of Federal Regulations, 2011 CFR

2011-07-01

... combustible materials from passing over the burner units. (e) If intake air heaters use liquefied fuel systems... measurement of the carbon monoxide concentration at the bottom of each shaft, slope, or in the drift opening... a carbon monoxide sensor that is calibrated with a known concentration of carbon monoxide and air at...

46 CFR 116.433 - Windows and air ports in fire control boundaries.

Code of Federal Regulations, 2011 CFR

2011-10-01

... fitted with frames of steel or equivalent material. Glazing beads or angles of steel or equivalent... event of a fire if: (1) Where a steel frame is used, it is not arranged to retain the glass in place; or (2) A frame of aluminum or other material with low melting point is used. (d) A window or air port...

Incorporation of air into a snack food reduces energy intake

PubMed Central

Osterholt, Kathrin M.; Roe, Liane S.

2007-01-01

This study investigated how the air content of a familiar snack food affected energy intake and whether varying the method of serving the snack modified intake. We tested two versions of an extruded snack (cheese puffs) that were equal in energy density (5.7 kcal/g), but differed in energy per volume (less-aerated snack: 1.00 kcal/ml; more- aerated snack: 0.45 kcal/ml). In a within-subjects design, 16 women and 12 men consumed the snacks ad libitum in the laboratory during four afternoon sessions. A standard volume (1250 ml) of each snack was served once in a bowl and once in an opaque bag. Results showed that intake of the two snacks differed significantly by energy (p=0.0003) and volume (p<0.0001); subjects consumed 21% less weight and energy (70±17 kcal) of the more-aerated snack than the less-aerated snack, although they consumed a 73% greater volume of the more-aerated snack (239±24 ml). These findings suggest that subjects responded to both the weight and volume of the snack. Despite differences in intake, hunger and fullness ratings did not differ across conditions. The serving method did not significantly affect intake. Results from this study indicate that incorporating air into food provides a strategy to reduce energy intake from energy-dense snacks. PMID:17188782

Incorporation of air into a snack food reduces energy intake.

PubMed

Osterholt, Kathrin M; Roe, Liane S; Rolls, Barbara J

2007-05-01

This study investigated how the air content of a familiar snack food affected energy intake and whether varying the method of serving the snack modified intake. We tested two versions of an extruded snack (cheese puffs) that were equal in energy density (5.7 kcal/g), but differed in energy per volume (less-aerated snack: 1.00 kcal/ml; more-aerated snack: 0.45 kcal/ml). In a within-subjects design, 16 women and 12 men consumed the snacks ad libitum in the laboratory during four afternoon sessions. A standard volume (1250 ml) of each snack was served once in a bowl and once in an opaque bag. Results showed significant differences in intake of the two snacks by energy (p=0.0003) and volume (p<0.0001); subjects consumed 21% less weight and energy (70+/-17 kcal) of the more-aerated snack than the less-aerated snack, although they consumed a 73% greater volume of the more-aerated snack (239+/-24 ml). These findings suggest that subjects responded to both the weight and volume of the snack. Despite differences in intake, hunger and fullness ratings did not differ across conditions. The serving method did not significantly affect intake. Results from this study indicate that incorporating air into food provides a strategy to reduce energy intake from energy-dense snacks.

Second Line of Defense, Port of Buenos Aires and Exolgan Container Terminal Operational Testing and Evaluation Plan, Buenos Aires, Argentina

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roberts, Bryan W.

2012-08-23

The Office of the Second Line of Defense (SLD) Megaports project team for Argentina will conduct operational testing and evaluation (OT&E) at Exolgan Container Terminal at the Port of Dock Sud from July 16-20, 2012; and at the Port of Buenos Aires from September 3-7, 2012. SLD is installing radiation detection equipment to screen export, import, and transshipment containers at these locations. The purpose of OT&E is to validate and baseline an operable system that meets the SLD mission and to ensure the system continues to perform as expected in an operational environment with Argentina Customs effectively adjudicating alarms.

Forced-air warming design: evaluation of intake filtration, internal microbial buildup, and airborne-contamination emissions.

PubMed

Reed, Mike; Kimberger, Oliver; McGovern, Paul D; Albrecht, Mark C

2013-08-01

Forced-air warming devices are effective for the prevention of surgical hypothermia. However, these devices intake nonsterile floor-level air, and it is unknown whether they have adequate filtration measures to prevent the internal buildup or emission of microbial contaminants. We rated the intake filtration efficiency of a popular current-generation forced-air warming device (Bair Hugger model 750, Arizant Healthcare) using a monodisperse sodium chloride aerosol in the laboratory. We further sampled 23 forced-air warming devices (same model) in daily hospital use for internal microbial buildup and airborne-contamination emissions via swabbing and particle counting. Laboratory testing found the intake filter to be 63.8% efficient. Swabbing detected microorganisms within 100% of the forced-air warming blowers sampled, with isolates of coagulase-negative staphylococci, mold, and micrococci identified. Particle counting showed 96% of forced-air warming blowers to be emitting significant levels of internally generated airborne contaminants out of the hose end. These findings highlight the need for upgraded intake filtration, preferably high-efficiency particulate air filtration (99.97% efficient), on current-generation forced-air warming devices to reduce contamination buildup and emission risks.

Design of a small personal air monitor and its application in aircraft.

PubMed

van Netten, Chris

2009-01-15

A small air sampling system using standard air filter sampling technology has been used to monitor the air in aircraft. The device is a small ABS constructed cylinder 5 cm in diameter and 9 cm tall and can be operated by non technical individuals at an instant notice. It is completely self contained with a 4 AAA cell power supply, DC motor, a centrifugal fan, and accommodates standard 37 mm filters and backup pads. The monitor is totally enclosed and pre assembled in the laboratory. A 45 degrees twist of the cap switches on the motor and simultaneously opens up the intake ports and exhaust ports allowing air to pass through the filter. A reverse 45 degrees twist of the cap switches off the motor and closes all intake and exhaust ports, completely enclosing the filter. The whole monitor is returned to the laboratory by standard mail for analysis and reassembly for future use. The sampler has been tested for electromagnetic interference and has been approved for use in aircraft during all phases of flight. A set of samples taken by a BAe-146-300 crew member during two flights in the same aircraft and analyzed by GC-MS, indicated exposure to tricresyl phosphate (TCP) levels ranging from 31 to 83 nanograms/m(3) (detection limit <4.5 nanograms/m(3)). The latter elevated level was associated with the use of the auxiliary power unit (APU) in the aircraft. It was concluded that the air sampler was capable of monitoring air concentrations of TCP isomers in aircraft above 4.5 nanogram/m(3).

Self-regulating fuel staging port for turbine combustor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Van Nieuwenhuizen, William F.; Fox, Timothy A.; Williams, Steven

2014-07-08

A port (60) for axially staging fuel and air into a combustion gas flow path 28 of a turbine combustor (10A). A port enclosure (63) forms an air path through a combustor wall (30). Fuel injectors (64) in the enclosure provide convergent fuel streams (72) that oppose each other, thus converting velocity pressure to static pressure. This forms a flow stagnation zone (74) that acts as a valve on airflow (40, 41) through the port, in which the air outflow (41) is inversely proportion to the fuel flow (25). The fuel flow rate is controlled (65) in proportion to enginemore » load. At high loads, more fuel and less air flow through the port, making more air available to the premixing assemblies (36).« less

Droplet size distributions of adjuvant-amended sprays from an air-assisted five-port PWM nozzle

USDA-ARS?s Scientific Manuscript database

Verification of droplet size distributions is essential for the development of real-time variable-rate sprayers that synchronize spray outputs with canopy structures. Droplet sizes from a custom-designed, air-assisted, five-port nozzle coupled with a pulse-width-modulated (PWM) solenoid valve were m...

Prototype Systems for Measuring Outdoor Air Intake Rates in Rooftop Air Handlers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fisk, William J.; Chan, Wanyu R.; Hotchi, Toshifumi

2015-01-01

The widespread absence of systems for real-time measurement and feedback control, of minimum outdoor air intake rates in HVAC systems contributes to the poor control of ventilation rates in commercial buildings. Ventilation rates affect building energy consumption and influence occupant health. The project designed fabricated and tested four prototypes of systems for measuring rates of outdoor air intake into roof top air handlers. All prototypes met the ±20% accuracy target at low wind speeds, with all prototypes accurate within approximately ±10% after application of calibration equations. One prototype met the accuracy target without a calibration. With two of four prototypemore » measurement systems, there was no evidence that wind speed or direction affected accuracy; however, winds speeds were generally below usually 3.5 m s -1 (12.6 km h -1) and further testing is desirable. The airflow resistance of the prototypes was generally less than 35 Pa at maximum RTU air flow rates. A pressure drop of this magnitude will increase fan energy consumption by approximately 4%. The project did not have resources necessary to estimate costs of mass produced systems. The retail cost of components and materials used to construct prototypes ranged from approximately $1,200 to $1,700. The test data indicate that the basic designs developed in this project, particularly the designs of two of the prototypes, have considerable merit. Further design refinement, testing, and cost analysis would be necessary to fully assess commercial potential. The designs and test results will be communicated to the HVAC manufacturing community.« less

40 CFR 1065.670 - NOX intake-air humidity and temperature corrections.

Code of Federal Regulations, 2010 CFR

2010-07-01

... concentrations for intake-air humidity. You may use a time-weighted mean combustion air humidity to calculate this correction if your combustion air humidity remains within a tolerance of ±0.0025 mol/mol of the... equation: ER30AP10.095 Example: x NOxuncor = 700.5 µmol/mol x H2O = 0.022 mol/mol x NOxcor = 700.5 · (9.953...

40 CFR 1065.670 - NOX intake-air humidity and temperature corrections.

Code of Federal Regulations, 2011 CFR

2011-07-01

... concentrations for intake-air humidity. You may use a time-weighted mean combustion air humidity to calculate this correction if your combustion air humidity remains within a tolerance of ±0.0025 mol/mol of the... equation: ER30AP10.095 Example: x NOxuncor = 700.5 µmol/mol x H2O = 0.022 mol/mol x NOxcor = 700.5 · (9.953...

Modelling the emissions from ships in ports and their impact on air quality in the metropolitan area of Hamburg

NASA Astrophysics Data System (ADS)

Ramacher, Martin; Karl, Matthias; Aulinger, Armin; Bieser, Johannes; Matthias, Volker; Quante, Markus

2016-04-01

Exhaust emissions from shipping contribute significantly to the anthropogenic burden of air pollutants such as nitrogen oxides (NOX) and particulate matter (PM). Ships emit not only when sailing on open sea, but also when approaching harbors, during port manoeuvers and at berth to produce electricity and heat for the ship's operations. This affects the population of harbor cities because long-term exposure to PM and NOX has significant effects on human health. The European Union has therefore has set air quality standards for air pollutants. Many port cities have problems meeting these standards. The port of Hamburg with around 10.000 ship calls per year is Germany's largest seaport and Europe's second largest container port. Air quality standard reporting in Hamburg has revealed problems in meeting limits for NO2 and PM10. The amount and contribution of port related ship emissions (38% for NOx and 17% for PM10) to the overall emissions in the metropolitan area in 2005 [BSU Hamburg (2012): Luftreinhalteplan für Hamburg. 1. Fortschreibung 2012] has been modelled with a bottom up approach by using statistical data of ship activities in the harbor, technical vessel information and specific emission algorithms [GAUSS (2008): Quantifizierung von gasförmigen Emissionen durch Maschinenanlagen der Seeschiffart an der deutschen Küste]. However, knowledge about the spatial distribution of the harbor ship emissions over the city area is crucial when it comes to air quality standards and policy decisions to protect human health. Hence, this model study examines the spatial distribution of harbor ship emissions (NOX, PM10) and their deposition in the Hamburg metropolitan area. The transport and chemical transformation of atmospheric pollutants is calculated with the well-established chemistry transport model TAPM (The Air Pollution Model). TAPM is a three-dimensional coupled prognostic meteorological and air pollution model with a condensed chemistry scheme including

33 CFR 165.151 - Safety Zones; Fireworks Displays, Air Shows and Swim Events in the Captain of the Port Long...

Code of Federal Regulations, 2012 CFR

2012-07-01

....22″ W (NAD 83). 7.33Clam Shell Foundation Fireworks • Location: Waters of Three Mile Harbor, East..., Air Shows and Swim Events in the Captain of the Port Long Island Sound Zone. 165.151 Section 165.151... Swim Events in the Captain of the Port Long Island Sound Zone. (a) Regulations. (1) The general...

Northwest Ports Achievements in Reducing Emissions and Improving Performance

EPA Pesticide Factsheets

Case history on the status of the Northwest Ports Clean Air Strategy for the Port of Seattle, Port of Tacoma, and Port Metro Vancouver. Presents key objectives, emission and performance goals and outcomes.

Fabrication of a smart air intake structure using shape memory alloy wire embedded composite

NASA Astrophysics Data System (ADS)

Jung, Beom-Seok; Kim, Min-Saeng; Kim, Ji-Soo; Kim, Yun-Mi; Lee, Woo-Yong; Ahn, Sung-Hoon

2010-05-01

Shape memory alloys (SMAs) have been actively studied in many fields utilizing their high energy density. Applying SMA wire-embedded composite to aerospace structures, such as air intake of jet engines and guided missiles, is attracting significant attention because it could generate a comparatively large actuating force. In this research, a scaled structure of SMA wire-embedded composite was fabricated for the air intake of aircraft. The structure was composed of several prestrained Nitinol (Ni-Ti) SMA wires embedded in ∩-shape glass fabric reinforced plastic (GFRP), and it was cured at room temperature for 72 h. The SMA wire-embedded GFRP could be actuated by applying electric current through the embedded SMA wires. The activation angle generated from the composite structure was large enough to make a smart air intake structure.

Web-based Air Quality Screening Tool for Near-port Assessments: Example of Application in Porto, Portugal

EPA Science Inventory

The HARMO conference presents an opportunity to extend and further develop ORD’s collaboration with our European colleagues. This paper describes the C-PORT application in Porto, Portugal as a part of the EU project AIRSHIP designed to evaluate the air quality impacts of m...

Ports Primer: 7.0 Environmental Impacts

EPA Pesticide Factsheets

Port operations can lead to environmental impacts on air, water and land. Many communities with environmental justice concerns also experience disparities in health outcomes that they attribute to exposure to emissions from port operations.

Ports Primer: 7.1 Environmental Impacts

EPA Pesticide Factsheets

Port operations can lead to environmental impacts on air, water and land. Many communities with environmental justice concerns also experience disparities in health outcomes that they attribute to exposure to emissions from port operations.

Internal combustion engine with rotary valve assembly having variable intake valve timing

DOEpatents

Hansen, Craig N.; Cross, Paul C.

1995-01-01

An internal combustion engine has rotary valves associated with movable shutters operable to vary the closing of intake air/fuel port sections to obtain peak volumetric efficiency over the entire range of speed of the engine. The shutters are moved automatically by a control mechanism that is responsive to the RPM of the engine. A foot-operated lever associated with the control mechanism is also used to move the shutters between their open and closed positions.

Integrating inland ports into the intermodal goods movement system for ports of Los Angeles and Long Beach.

DOT National Transportation Integrated Search

2008-02-01

Planners concerned with deep-water port operations are interested in strategies that improve : regional truck flows associated with the container trade while also mitigating related problems of : highway congestion and air pollution. An inland port o...

HVAC--the importance of clean intake section and dry air filter in cold climate.

PubMed

Hanssen, S O

2004-01-01

HVAC systems, if properly designed, installed, operated and maintained, will improve thermal conditions and air quality indoors. However, the success strongly depends on the design of the system and the quality of the components we use in our HVAC installations. Regrettably, several investigations have revealed that many HVAC installations have a lot of operational and maintenance problems, especially related to moisture, rain and snow entrainment. In short, it seems that too little attention is placed on the design of the intake section, despite the fact that there exists a large number of national and international guidelines and recommendations. This is a serious problem because the air intake is the initial component of the ventilation plant and as such the first line of defense against debris and other outdoor air pollutants. Unfortunately, the design is often an argued compromise between the architect, the civil engineer and the HVAC engineer. In the future, the technical, hygienic and microbiological feature of air intakes must be better ensured in order to avoid the air intake becoming a risk component as regards contamination and indoor air quality. Further, it seems that the magnitude of the problem is not well known, or recognized, by the building designers, engineers and professionals involved in the construction and operation of buildings. This fact needs to be addressed more seriously, because obviously there is a big difference between the idealistic architectonic design, engineering intentions and the real life situation. Several practical recommendations for design and operation of HVAC systems are presented. Following the recommendations will result in less pollution from the HVAC-system and increased indoor environmental quality.

Composting of empty fruit bunches in the tower composter - effect of air intake holes

NASA Astrophysics Data System (ADS)

Irvan; Husaini, T.; Trisakti, B.; Batubara, F.; Daimon, H.

2018-02-01

The process of composting empty fruit bunches (EFB) by mixing with activated liquid organic fertilizer (ALOF) is an alternative utilization of solid waste generated from palm oil mill. This study aims to find composting techniques of EFB and to obtain degradation data of composting EFB by varying the air intake holes to produce good quality compost. Composting process was carried out by tearing the EFB into four shreds, then put into the tower composter while adding ALOF until it reached the optimum moisture content of 55 -65%. During the composting process, we maintained moisture content at optimum conditions by adding ALOF. Variations of air intake holes area to the outer surface area of the composter are 0/44.314; 72.39/44.314 and 144.78/44.314 (cm2/cm2). Composting is carried out for forty days, however, based on the result, compost began to mature on the 10th day. The results revealed that there was an influence of air intake holes to the composting process. The best degradation of EFB was obtained on the variation of air intake holes 72.39/44.314 (cm2/cm2), pH 8.1, moisture content 79.14%, water holding capacity 60%, electrical conductivity 4.725 dS/m and C/N ratio 20.97.

30 CFR 57.22215 - Separation of intake and return air (I-A, II-A, III, and V-A mines).

Code of Federal Regulations, 2010 CFR

2010-07-01

... Separation of intake and return air (I-A, II-A, III, and V-A mines). Main intake and return air currents... for separation of air currents. Such wall or partition shall be constructed of reinforced concrete or... separation of main air currents in the same opening. Flexible ventilation tubing shall not exceed 250 feet in...

30 CFR 57.22215 - Separation of intake and return air (I-A, II-A, III, and V-A mines).

Code of Federal Regulations, 2011 CFR

2011-07-01

... Separation of intake and return air (I-A, II-A, III, and V-A mines). Main intake and return air currents... for separation of air currents. Such wall or partition shall be constructed of reinforced concrete or... separation of main air currents in the same opening. Flexible ventilation tubing shall not exceed 250 feet in...

Preliminary Design of the Low Speed Propulsion Air Intake of the LAPCAT-MR2 Aircraft

NASA Astrophysics Data System (ADS)

Meerts, C.; Steelant, J.; Hendrick, P.

2011-08-01

A supersonic air intake has been designed for the low speed propulsion system of the LAPCAT-MR2 aircraft. Development has been based on the XB-70 aircraft air intake which achieves extremely high performances over a wide operation range through the combined use of variable geometry and porous wall suction for boundary layer control. Design of the LAPCAT-MR2 intake has been operated through CFD simulations using DLR TAU-Code (perfect gas model - Menter SST turbulence model). First, a new boundary condition has been validated into the DLR TAU-Code (perfect gas model) for porous wall suction modelling. Standard test cases have shown surprisingly good agreement with both theoretical predictions and experimental results. Based upon this validation, XB-70 air intake performances have been assessed through CFD simulations over the subsonic, transonic and supersonic operation regions and compared to available flight data. A new simulation strategy was deployed avoiding numerical instabilities when initiating the flow in both transonic and supersonic operation modes. First, the flow must be initiated with a far field Mach number higher than the target flight Mach number. Additionally, the inlet backpressure may only be increased to its target value once the oblique shock pattern downstream the intake compression ramps is converged. Simulations using that strategy have shown excellent agreement with in-flight measurements for both total pressure recovery ratio and variable geometry schedule prediction. The demarcation between stable and unstable operation could be well reproduced. Finally, a modified version of the XB-70 air intake has been integrated in the elliptical intake on the LAPCAT vehicle. Operation of this intake in the LAPCAT-MR2 environment is under evaluation using the same simulation strategy as the one developed for the XB-70. Performances are assessed at several key operation points to assess viability of this design. This information will allow in a next

6. FAN HOUSE OF 8FOOT HIGH SPEED TUNNEL. AIR INTAKES ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. FAN HOUSE OF 8-FOOT HIGH SPEED TUNNEL. AIR INTAKES AND FILTERS ARE ENCLOSED IN THE UPPER LEVEL STRUCTURE. - NASA Langley Research Center, 8-Foot High Speed Wind Tunnel, 641 Thornell Avenue, Hampton, Hampton, VA

Truck Noise - VI A Diesel Exhaust and Air Intake Noise

DOT National Transportation Integrated Search

1973-07-01

Exhaust and air intake noise is studied on five truck and bus diesel engines; the Detroit Diesel 6-71 and 8V-71, the Cummins NHC-250 and NTC-350 and the Mack ENDT-675. The noise source is isolated and its sound level measured at a distance of 50 feet...

Experimental Studies of Active and Passive Flow Control Techniques Applied in a Twin Air-Intake

PubMed Central

Joshi, Shrey; Jindal, Aman; Maurya, Shivam P.; Jain, Anuj

2013-01-01

The flow control in twin air-intakes is necessary to improve the performance characteristics, since the flow traveling through curved and diffused paths becomes complex, especially after merging. The paper presents a comparison between two well-known techniques of flow control: active and passive. It presents an effective design of a vortex generator jet (VGJ) and a vane-type passive vortex generator (VG) and uses them in twin air-intake duct in different combinations to establish their effectiveness in improving the performance characteristics. The VGJ is designed to insert flow from side wall at pitch angle of 90 degrees and 45 degrees. Corotating (parallel) and counterrotating (V-shape) are the configuration of vane type VG. It is observed that VGJ has the potential to change the flow pattern drastically as compared to vane-type VG. While the VGJ is directed perpendicular to the side walls of the air-intake at a pitch angle of 90 degree, static pressure recovery is increased by 7.8% and total pressure loss is reduced by 40.7%, which is the best among all other cases tested for VGJ. For bigger-sized VG attached to the side walls of the air-intake, static pressure recovery is increased by 5.3%, but total pressure loss is reduced by only 4.5% as compared to all other cases of VG. PMID:23935422

76 FR 77996 - Notice of Issuance of Final Air Permits for Eni US Operating Co., Inc. and Port Dolphin Energy, LLC.

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-15

... Final Air Permits for Eni US Operating Co., Inc. and Port Dolphin Energy, LLC. AGENCY: Environmental... 27, 2011, the EPA issued a final Outer Continental Shelf (OCS) air permit for Eni US Operating Inc. (Eni). This permit became effective on November 28, 2011. In addition, the EPA issued a final...

Advancing Solutions to Support More Sustainable Ports (March 2014 Webinar)

EPA Pesticide Factsheets

To exchange views and develop a shared understanding of the challenges and opportunities of ports and port communities, EPA's Office of Transportation and Air Quality is hosting a series of webinars, bringing together port stakeholders.

Modeling and control of fuel distribution in a dual-fuel internal combustion engine leveraging late intake valve closings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kassa, Mateos; Hall, Carrie; Ickes, Andrew

trapped air and port injected fuel to flow back out of the cylinders into the intake manifold. The fuel that is pushed back in the intake manifold is then unevenly redistributed across the cylinders largely due to the dominating direction of the flow in the intake manifold. The effects of IVC as well as the impact of intake runner length on fuel distribution were quantitatively analyzed and a model was developed that can be used to accurately predict the fuel distribution of the port injected fuel at different operating conditions with an average estimation error of 1.5% in cylinder-specific fuel flow.« less

9 CFR 93.703 - Ports designated for importation.

Code of Federal Regulations, 2011 CFR

2011-01-01

..., except as provided in paragraph (b) of this section, only through the following ports: (1) Air and ocean... Springs, VT; Oroville and Sumas, WA. (3) Mexican border ports. Douglas, Naco, Nogales, Sasabe, and San...

9 CFR 93.703 - Ports designated for importation.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., except as provided in paragraph (b) of this section, only through the following ports: (1) Air and ocean... Springs, VT; Oroville and Sumas, WA. (3) Mexican border ports. Douglas, Naco, Nogales, Sasabe, and San...

Method and apparatus for extracting water from air using a desiccant

DOEpatents

Spletzer, Barry L.; Callow, Diane Schafer

2003-01-01

The present invention provides a method and apparatus for extracting liquid water from moist air using minimal energy input. The method can be considered as four phases: (1) adsorbing water from air into a desiccant, (2) isolating the water-laden desiccant from the air source, (3) desorbing water as vapor from the desiccant into a chamber, and (4) isolating the desiccant from the chamber, and compressing the vapor in the chamber to form liquid condensate. The liquid condensate can be removed for use. Careful design of the dead volumes and pressure balances can minimize the energy required. The dried air can be exchanged for fresh moist air and the process repeated. An apparatus comprises a first chamber in fluid communication with a desiccant, and having ports to intake moist air and exhaust dried air. The apparatus also comprises a second chamber in fluid communication with the desiccant. The second chamber allows variable internal pressure, and has a port for removal of liquid condensate. Each chamber can be configured to be isolated or in communication with the desiccant. The first chamber can be configured to be isolated or in communication with a course of moist air. Various arrangements of valves, pistons, and chambers are described.

A web-based screening tool for near-port air quality assessments

EPA Science Inventory

The Community model for near-PORT applications (C-PORT) is a screening tool with an intended purpose of calculating differences in annual averaged concentration patterns and relative contributions of various source categories over the spatial domain within about 10 km of the port...

[Attempt to reduce the formaldehyde concentration by blowing cooled fresh air down in to the breathing zone of medical students from an admission port on the ceiling during gross anatomy class].

PubMed

Takayanagi, Masaaki; Sakai, Makoto; Ishikawa, Youichi; Murakami, Kunio; Kimura, Akihiko; Kakuta, Sachiko; Sato, Fumi

2008-09-01

Cadavers in gross anatomy laboratories at most medical schools are conventionally embalmed in formaldehyde solution, which is carcinogenic to humans. Medical students and instructors are thus exposed to formaldehyde vapors emitted from cadavers during dissection. To reduce high formaldehyde concentrations in the breathing zone above cadavers being examined by anatomy medical students provisionally, dissection beds were located under existing admission ports on the ceiling to supply cooled fresh air from the admission port blowing downward on to the cadaver. In all cases, compared to normal condition, the downward flow of cooled fresh air from an admission port reduced formaldehyde concentrations by 0.09-0.98 ppm and reduced to 12.6-65.4% in the air above a cadaver in the breathing zone of students. The formaldehyde concentrations above cadavers under admission ports were not more than the formaldehyde concentrations between beds representing the indoor formaldehyde concentrations. Although the application of an existing admission port on the ceiling in this study did not remove formaldehyde, the downflow of cooled fresh air using this system reduced the formaldehyde concentration in the air above cadavers being attended by anatomy students during dissections. These results suggest the need for reducing formaldehyde levels in gross anatomy laboratories using fundamental countermeasures in order to satisfy the guidelines of 0.08 ppm established by the World Health Organization and the Japan Ministry of Health, Labor and Welfare.

Vessels, Marinas and Ports

EPA Pesticide Factsheets

An overview of EPA’s vessels (recreational/commercial/military), marinas, and ports programs and the regulatory (permits/rules) and non-regulatory approaches for addressing their associated environmental impacts, such as air and water pollution.

Impact of emissions from the Los Angeles port region on San Diego air quality during regional transport events.

PubMed

Ault, Andrew P; Moore, Meagan J; Furutani, Hiroshi; Prather, Kimberly A

2009-05-15

Oceangoing ships emit an estimated 1.2-1.6 million metric tons (Tg) of PM10 per year and represent a significant source of air pollution to coastal communities. As shown herein, ship and other emissions near the Los Angeles and Long Beach Port region strongly influence air pollution levels in the San Diego area. During time periods with regional transport, atmospheric aerosol measurements in La Jolla, California show an increase in 0.5-1 microm sized single particles with unique signatures including soot, metals (i.e., vanadium, iron, and nickel), sulfate, and nitrate. These particles are attributed to primary emissions from residual oil sourcessuch as ships and refineries, as well as traffic in the port region, and secondary processing during transport. During regional transport events, particulate matter concentrations were 2-4 times higher than typical average concentrations from local sources, indicating the health, environmental, and climate impacts from these emission sources must be taken into consideration in the San Diego region. Unless significant regulations are imposed on shipping-related activities, these emission sources will become even more important to California air quality as cars and truck emissions undergo further regulations and residual oil sources such as shipping continue to expand.

A study of optimum cowl shapes and flow port locations for minimum drag with effective engine cooling, volume 2

NASA Technical Reports Server (NTRS)

Fox, S. R.; Smetana, F. O.

1980-01-01

The listings, user's instructions, sample inputs, and sample outputs of two computer programs which are especially useful in obtaining an approximate solution of the viscous flow over an arbitrary nonlifting three dimensional body are provided. The first program performs a potential flow solution by a well known panel method and readjusts this initial solution to account for the effects of the boundary layer displacement thickness, a nonuniform but unidirectional onset flow field, and the presence of air intakes and exhausts. The second program is effectually a geometry package which allows the user to change or refine the shape of a body to satisfy particular needs without a significant amount of human intervention. An effort to reduce the cruise drag of light aircraft through an analytical study of the contributions to the drag arising from the engine cowl shape and the foward fuselage area and also that resulting from the cooling air mass flowing through intake and exhaust sites on the nacelle is presented. The programs may be effectively used to determine the appropriate body modifications or flow port locations to reduce the cruise drag as well as to provide sufficient air flow for cooling the engine.

Measurement and Modeling of Near-Road & Near-Port Air Quality

EPA Science Inventory

This presentation provides a summary of mobile monitoring assessment studies conducted on major interstates in Detroit, Michigan and Phoenix, Arizona along with a near-port assessment focusing on the Port of Charleston in South Carolina, USA. We will also present our mobile measu...

Goods Movement and Ports: Community Impacts and Collaborative Solutions (January 2014 Webinar)

EPA Pesticide Factsheets

To exchange views and develop a shared understanding of the challenges and opportunities of ports and port communities, EPA's Office of Transportation and Air Quality is hosting a series of webinars, bringing together port stakeholders.

Monovalve with integrated fuel injector and port control valve, and engine using same

DOEpatents

Milam, David M.

2002-01-01

Each cylinder of an internal combustion engine includes a combined gas exchange valve and fuel injector with a port control valve. The port control valve operates to open either an intake passage or an exhaust passage. The operation of the combined device is controlled by a pair of electrical actuators. The device is hydraulically actuated.

ROCKET PORT CLOSURE

DOEpatents

Mattingly, J.T.

1963-02-12

This invention provides a simple pressure-actuated closure whereby windowless observation ports are opened to the atmosphere at preselected altitudes. The closure comprises a disk which seals a windowless observation port in rocket hull. An evacuated instrument compartment is affixed to the rocket hull adjacent the inner surface of the disk, while the outer disk surface is exposed to the atmosphere through which the rocket is traveling. The pressure differential between the evacuated instrument compartment and the relatively high pressure external atmosphere forces the disk against the edge of the observation port, thereby effecting a tight seai. The instrument compartment is evacuated to a pressure equal to the atmospheric pressure existing at the altitude at which it is desiretl that the closure should open. When the rocket reaches this preselected altitude, the inwardly directed atmospheric force on the disk is just equaled by the residual air pressure force within the instrument compartment. Consequently, the closure disk falls away and uncovers the open observation port. The separation of the disk from the rocket hull actuates a switch which energizes the mechanism of a detecting instrument disposed within the instrument compartment. (AE C)

System Mapping to Promote Resilient Decision-Making in Port Communities

EPA Science Inventory

Port communities are particularly vulnerable to environmental hazards including: extreme weather, toxic air pollution, hazardous materials storage and transport, and operational and accidental environmental emissions from industry. Following the Panama Canal expansion, port expa...

9 CFR 93.503 - Ports designated for the importation of swine.

Code of Federal Regulations, 2014 CFR

2014-01-01

... of swine. 93.503 Section 93.503 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION... PRODUCTS; REQUIREMENTS FOR MEANS OF CONVEYANCE AND SHIPPING CONTAINERS Swine § 93.503 Ports designated for the importation of swine. (a) Air and ocean ports. The following ports have APHIS inspection and...

9 CFR 93.503 - Ports designated for the importation of swine.

Code of Federal Regulations, 2012 CFR

2012-01-01

... of swine. 93.503 Section 93.503 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION... PRODUCTS; REQUIREMENTS FOR MEANS OF CONVEYANCE AND SHIPPING CONTAINERS Swine § 93.503 Ports designated for the importation of swine. (a) Air and ocean ports. The following ports have APHIS inspection and...

9 CFR 93.503 - Ports designated for the importation of swine.

Code of Federal Regulations, 2013 CFR

2013-01-01

... of swine. 93.503 Section 93.503 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION... PRODUCTS; REQUIREMENTS FOR MEANS OF CONVEYANCE AND SHIPPING CONTAINERS Swine § 93.503 Ports designated for the importation of swine. (a) Air and ocean ports. The following ports have APHIS inspection and...

9 CFR 93.503 - Ports designated for the importation of swine.

Code of Federal Regulations, 2011 CFR

2011-01-01

... of swine. 93.503 Section 93.503 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION... PRODUCTS; REQUIREMENTS FOR MEANS OF CONVEYANCE AND SHIPPING CONTAINERS Swine § 93.503 Ports designated for the importation of swine. (a) Air and ocean ports. The following ports have APHIS inspection and...

Measuring the Impact of Port of Charleston Activities on Local Air Quality

EPA Science Inventory

Ports are a critical feature of the nation’s economy; port commerce supports 13 million jobs and contributes $3.15 trillion to the economy. The value of goods shipped through seaports represents 11% of the GDP. The US has 360 commercial ports, including 150 deep-draft seaports....

9 CFR 93.203 - Ports designated for the importation of poultry.

Code of Federal Regulations, 2014 CFR

2014-01-01

...; Baltimore, Maryland; Minneapolis, Minnesota; Great Falls, Montana; Portland, Oregon; San Juan, Puerto Rico... for the importation of poultry. (a) Air and ocean ports. The following ports have APHIS inspection and...

9 CFR 93.303 - Ports designated for the importation of horses.

Code of Federal Regulations, 2012 CFR

2012-01-01

...; Dayton, Ohio; Portland, Oregon; San Juan, Puerto Rico; Memphis, Tennessee (no live animals); Galveston... the importation of horses. (a) Air and ocean ports. The following ports have APHIS inspection and...

9 CFR 93.203 - Ports designated for the importation of poultry.

Code of Federal Regulations, 2013 CFR

2013-01-01

...; Baltimore, Maryland; Minneapolis, Minnesota; Great Falls, Montana; Portland, Oregon; San Juan, Puerto Rico... for the importation of poultry. (a) Air and ocean ports. The following ports have APHIS inspection and...

9 CFR 93.303 - Ports designated for the importation of horses.

Code of Federal Regulations, 2013 CFR

2013-01-01

...; Dayton, Ohio; Portland, Oregon; San Juan, Puerto Rico; Memphis, Tennessee (no live animals); Galveston... the importation of horses. (a) Air and ocean ports. The following ports have APHIS inspection and...

9 CFR 93.203 - Ports designated for the importation of poultry.

Code of Federal Regulations, 2012 CFR

2012-01-01

...; Baltimore, Maryland; Minneapolis, Minnesota; Great Falls, Montana; Portland, Oregon; San Juan, Puerto Rico... for the importation of poultry. (a) Air and ocean ports. The following ports have APHIS inspection and...

9 CFR 93.303 - Ports designated for the importation of horses.

Code of Federal Regulations, 2014 CFR

2014-01-01

...; Dayton, Ohio; Portland, Oregon; San Juan, Puerto Rico; Memphis, Tennessee (no live animals); Galveston... the importation of horses. (a) Air and ocean ports. The following ports have APHIS inspection and...

9 CFR 93.303 - Ports designated for the importation of horses.

Code of Federal Regulations, 2011 CFR

2011-01-01

... the importation of horses. (a) Air and ocean ports. The following ports have APHIS inspection and... Dakota; Derby Line and Highgate Springs, Vermont; Oroville and Sumas, Washington. (2) International Falls...

9 CFR 93.403 - Ports designated for the importation of ruminants.

Code of Federal Regulations, 2013 CFR

2013-01-01

...; Portland, Oregon; San Juan, Puerto Rico; Memphis, Tennessee (no live animals); El Paso, Galveston, and... for the importation of ruminants. (a) Air and ocean ports. The following ports have APHIS inspection...

9 CFR 93.403 - Ports designated for the importation of ruminants.

Code of Federal Regulations, 2014 CFR

2014-01-01

...; Portland, Oregon; San Juan, Puerto Rico; Memphis, Tennessee (no live animals); El Paso, Galveston, and... for the importation of ruminants. (a) Air and ocean ports. The following ports have APHIS inspection...

9 CFR 93.403 - Ports designated for the importation of ruminants.

Code of Federal Regulations, 2012 CFR

2012-01-01

...; Portland, Oregon; San Juan, Puerto Rico; Memphis, Tennessee (no live animals); El Paso, Galveston, and... for the importation of ruminants. (a) Air and ocean ports. The following ports have APHIS inspection...

9 CFR 93.403 - Ports designated for the importation of ruminants.

Code of Federal Regulations, 2011 CFR

2011-01-01

... for the importation of ruminants. (a) Air and ocean ports. The following ports have APHIS inspection..., and Champlain, New York; Dunseith, Pembina, and Portal, North Dakota; Derby Line and Highgate Springs...

Baseline Air Quality Assessment of Goods Movement Activities before the Port of Charleston Expansion: A Community–University Collaborative

PubMed Central

Wilson, Sacoby M.; Tarver, Siobhan L.; Svendsen, Erik; Jiang, Chengsheng; Ogunsakin, Olalekan A.; Zhang, Hongmei; Campbell, Dayna; Fraser-Rahim, Herbert

2017-01-01

Abstract As the demand for goods continues to increase, a collective network of transportation systems is required to facilitate goods movement activities. This study examines air quality near the Port of Charleston before its expansion and briefly describes the establishment and structure of a community–university partnership used to monitor existing pollution. Particulate matter (PM) concentrations (PM2.5 and PM10) were measured using the Thermo Fisher Scientific Partisol 2000i-D Dichotomous Air Sampler, Thermo Scientific Dichotomous Sequential Air Sampler Partisol-Plus 2025-D, and Rupprecht & Patashnick TEOM Series 1400 Sampler at neighborhood (Union Heights, Rosemont, and Accabee) and reference (FAA2.5 and Jenkins Street) sites. Descriptive statistics were performed and an ANOVA (analysis of variance) was calculated to find the difference in overall mean 24-hour PM average concentrations in communities impacted by environmental injustice. PM2.5 (15.2 μg/m3) and PM10 (27.2 μg/m3) maximum concentrations were highest in neighborhoods such as Union Heights neighborhoods due to more goods movement activities. Nevertheless, there was no statistically significant difference in mean concentrations of PM2.5 and PM10 across neighborhood sites. In contrast, mean PM10 neighborhood concentrations were significantly lower than mean PM10 reference concentrations for Union Heights (p = 0.00), Accabee (p ≤ 0.0001), and Rosemont (p = 0.01). Although PM concentrations were lower than current National Ambient Air Quality Standards, this study demonstrated how community–university partners can work collectively to document baseline PM concentrations that will be used to examine changes in air quality after the port expansion brings additional goods movement activities to the area. PMID:29576842

9 CFR 93.203 - Ports designated for the importation of poultry.

Code of Federal Regulations, 2011 CFR

2011-01-01

... for the importation of poultry. (a) Air and ocean ports. The following ports have APHIS inspection and..., and Champlain, New York; Dunseith, Pembina, and Portal, North Dakota; Derby Line and Highgate Springs...

Compressor ported shroud for foil bearing cooling

DOEpatents

Elpern, David G [Los Angeles, CA; McCabe, Niall [Torrance, CA; Gee, Mark [South Pasadena, CA

2011-08-02

A compressor ported shroud takes compressed air from the shroud of the compressor before it is completely compressed and delivers it to foil bearings. The compressed air has a lower pressure and temperature than compressed outlet air. The lower temperature of the air means that less air needs to be bled off from the compressor to cool the foil bearings. This increases the overall system efficiency due to the reduced mass flow requirements of the lower temperature air. By taking the air at a lower pressure, less work is lost compressing the bearing cooling air.

Monovalve with integrated fuel injector and port control valve, and engine using same

DOEpatents

Milam, David M.

2001-11-06

An engine includes an engine casing that defines a hollow piston cavity separated from an exhaust passage and an intake passage by a valve seat. A gas exchange valve member is positioned adjacent the valve seat and is moveable between an open position and a closed position. The gas exchange valve member also defines an opening that opens into the hollow piston cavity. A needle valve member is positioned in the gas exchange valve member adjacent a nozzle outlet and is moveable between an inject position and a blocked position. A port control valve member, which has a hydraulic surface, is mounted around the gas exchange valve member and moveable between an intake position and an exhaust position. A pilot valve is moveable between a first position at which the port control hydraulic surface is exposed to a source of high pressure fluid, and a second position at which the port control hydraulic surface is exposed to a source of low pressure fluid.

Temporary vs. Permanent Sub-slab Ports: A Comparative ...

EPA Pesticide Factsheets

Vapor intrusion (VI) is the migration of subsurface vapors, including radon and volatile organic compounds (VOCs), from the subsurface to indoor air. The VI exposure pathway extends from the contaminant source, which can be impacted soil, non-aqueous phase liquid, or contaminated groundwater, to indoor air-exposure points. Therefore, contaminated matrices may include groundwater, soil, soil gas, and indoor air. VOC contaminants of concern typically include halogenated solvents such as trichloroethene, tetrachloroethene, and chloroform, as well as petroleum hydrocarbons, such as the aromatic VOCs benzene, toluene, and xylenes. Radon is a colorless radioactive gas that is released by radioactive decay of radionuclides in rock and soil that migrate into homes through VI in a similar fashion to VOCs. This project focused on the performance of permanent versus temporary sub-slab sampling ports for the determination of VI of halogenated VOCs and radon into an unoccupied house. VOC and radon concentrations measured simultaneously in soil gas using collocated temporary and permanent ports appeared to be independent of the type of port. The variability between collocated temporary and permanent ports was much less than the spatial variability between different locations within a single residential duplex. The agreement of the majority of VOC and radon concentrations, 0–36% relative percent difference, and 2–19% relative standard deviation respectively, of each sub-sl

Benchmark dynamics in the environmental performance of ports.

PubMed

Puig, Martí; Michail, Antonis; Wooldridge, Chris; Darbra, Rosa Mari

2017-08-15

This paper analyses the 2016 environmental benchmark performance of the port sector, based on a wide representation of EcoPorts members. This is the fifth time that this study has been conducted as an initiative of the European Sea Ports Organisation (ESPO). The data and results are derived from the Self-Diagnosis Method (SDM), a concise checklist against which port managers can self-assess the environmental management of their port in relation to the performance of the EcoPorts membership. The SDM tool was developed in the framework of the ECOPORTS project (2002-2005) and it is managed by ESPO. A total number of 91 ports from 20 different European Maritime States contributed to this evaluation. The main results are that air quality remains as the top environmental priority of the respondent ports, followed by energy consumption and noise. In terms of environmental management, the study confirms that key components are commonly implemented in the majority of European ports. 94% of contributing ports have a designated environmental manager, 92% own an environmental policy and 82% implement an environmental monitoring program. Waste is identified as the most monitored issue in ports (80%), followed by energy consumption (73%) and water quality (70%). Copyright © 2017 Elsevier Ltd. All rights reserved.

Final Ports Initiative Workgroup Report: Recommendations for the U.S. EPA

EPA Pesticide Factsheets

The Port Initiative Workgroup was organized under the Clean Air Act Advisory Committee for the purpose of discussing and identifying recommendations related to Ports. The workgroup is part of the Mobile Sources Technical Review Subcommittee.

9 CFR 98.33 - Ports designated for the importation of certain animal semen.

Code of Federal Regulations, 2011 CFR

2011-01-01

... of certain animal semen. 98.33 Section 98.33 Animals and Animal Products ANIMAL AND PLANT HEALTH... ANIMAL PRODUCTS IMPORTATION OF CERTAIN ANIMAL EMBRYOS AND ANIMAL SEMEN Certain Animal Semen § 98.33 Ports designated for the importation of certain animal semen. (a) Air and ocean ports. The following air and ocean...

9 CFR 98.33 - Ports designated for the importation of certain animal semen.

Code of Federal Regulations, 2010 CFR

2010-01-01

... of certain animal semen. 98.33 Section 98.33 Animals and Animal Products ANIMAL AND PLANT HEALTH... ANIMAL PRODUCTS IMPORTATION OF CERTAIN ANIMAL EMBRYOS AND ANIMAL SEMEN Certain Animal Semen § 98.33 Ports designated for the importation of certain animal semen. (a) Air and ocean ports. The following air and ocean...

Ceramic port shields cast in an iron engine head

NASA Technical Reports Server (NTRS)

Hakim, Nabil S.; Groeneweg, Mark A.

1989-01-01

Silicon nitride exhaust and intake port shields have been successfully cast into a gray iron cylinder head of a heavy duty diesel single cylinder research engine. Careful design considerations, finite element, and probability of survival analyses indicated viability of the design. Foundry experience, NDE, and failure investigations are reported.

[Ambient air interference in oxygen intake measurements in liquid incubating media with the use of open polarographic cells].

PubMed

Miniaev, M V; Voronchikhina, L I

2007-01-01

A model of oxygen intake by aerobic bio-objects in liquid incubating media was applied to investigate the influence air-media interface area on accuracy of measuring the oxygen intake and error value. It was shown that intrusion of air oxygen increases the relative error to 24% in open polarographic cells and to 13% in cells with a reduced interface area. Results of modeling passive media oxygenation laid a basis for proposing a method to reduce relative error by 66% for open cells and by 15% for cells with a reduced interface area.

Ports Primer: 7.5 Potential Community Interests

EPA Pesticide Factsheets

Communities have interests in environmental impacts of ports including environmental justice; public health outcomes; climate adaptation/resilience; air quality; ecological impacts; nuisance; and access to natural areas and open space.

Air-Quality Impacts and Intake Fraction of PM2.5 during the 2013 Rim Megafire.

PubMed

Navarro, Kathleen M; Cisneros, Ricardo; O'Neill, Susan M; Schweizer, Don; Larkin, Narasimhan K; Balmes, John R

2016-11-01

The 2013 Rim Fire was the third largest wildfire in California history and burned 257 314 acres in the Sierra Nevada Mountains. We evaluated air-quality impacts of PM 2.5 from smoke from the Rim Fire on receptor areas in California and Nevada. We employed two approaches to examine the air-quality impacts: (1) an evaluation of PM 2.5 concentration data collected by temporary and permanent air-monitoring sites and (2) an estimation of intake fraction (iF) of PM 2.5 from smoke. The Rim Fire impacted locations in the central Sierra nearest to the fire and extended to the northern Sierra Nevada Mountains of California and Nevada monitoring sites. Daily 24-h average PM 2.5 concentrations measured at 22 air monitors had an average concentration of 20 μg/m 3 and ranged from 0 to 450 μg/m 3 . The iF for PM 2.5 from smoke during the active fire period was 7.4 per million, which is slightly higher than representative iF values for PM 2.5 in rural areas and much lower than for urban areas. This study is a unique application of intake fraction to examine emissions-to-exposure for wildfires and emphasizes that air-quality impacts are not only localized to communities near large fires but can extend long distances and affect larger urban areas.

A Modified Triples Algorithm for Flush Air Data Systems that Allows a Variety of Pressure Port Configurations

NASA Technical Reports Server (NTRS)

Millman, Daniel R.

2017-01-01

Air Data Systems (FADS) are becoming more prevalent on re-entry vehicles, as evi- denced by the Mars Science Laboratory and the Orion Multipurpose Crew Vehicle. A FADS consists of flush-mounted pressure transducers located at various locations on the fore-body of a flight vehicle or the heat shield of a re-entry capsule. A pressure model converts the pressure readings into useful air data quantities. Two algorithms for converting pressure readings to air data have become predominant- the iterative Least Squares State Estimator (LSSE) and the Triples Algorithm. What follows herein is a new algorithm that takes advantage of the best features of both the Triples Algorithm and the LSSE. This approach employs the potential flow model and strategic differencing of the Triples Algorithm to obtain the defective flight angles; however, the requirements on port placement are far less restrictive, allowing for configurations that are considered optimal for a FADS.

Appraisal of Emissions from Ocean-going Vessels Coming to Kolkata Port, India

NASA Astrophysics Data System (ADS)

Mandal, Anindita; Biswas, Jhumoor; Roychowdhury, Soma; Farooqui, Zuber M.

2017-12-01

Rapid economic growth has escalated India's share in international trade. The pressure on these ports, which handle a substantial portion of the trade, has increased to perform with optimal efficiency, and decrease turnaround time so as to increase the number of ships visiting the port area. The caveat is that increased shipping activity is accompanied by enhanced emissions of harmful pollutants and green house gases. This study has revealed increased turnaround time for ships resulting in substantial emissions from auxiliary engines. There should be an optimum balance between operational control and environmental control of pollutants. Kolkata is a megacity with active riverine ports that can generate high levels of air quality emissions, especially NOx, SOx and particulate matter. An exhaustive annual emissions inventory based on ocean going vessels activity has been developed for 2013-2014 for Kolkata port, using recent EPA approved methodology. This includes greenhouse gas emissions from marine engines as well. The study indicates that amongst the different categories of ocean going ships, containers contribute the most (49%) of air and greenhouse gas emissions in 75th percentile class and above followed by general cargo (14%) and oil tankers (13%). The study depicts existing status of marine emissions in Kolkata port from ocean going vessels, which would serve in development of integrated air quality and climate change management plans and serve as a prototype for other major ports of India.

Impact of new diesel fuels used in port operations on subsurface quality

DOT National Transportation Integrated Search

2008-04-01

Diesel is widely used as fuel for operations in the port of Los Angeles - Long : Beach as well as for transport of goods to and from the port. Conventional diesel fuel : contributes disproportional to air pollution (particulate matter, NOx, CO, and :...

40 CFR 1065.125 - Engine intake air.

Code of Federal Regulations, 2010 CFR

2010-07-01

... engines with multiple intakes with separate humidity measurements at each intake, use a flow-weighted average humidity for NOX corrections. If individual flows of each intake are not measured, use good engineering judgment to estimate a flow-weighted average humidity. (3) Temperature. Good engineering judgment...

Ports Primer: 3.2 Port Governance

EPA Pesticide Factsheets

State and local governments are important players in port governance and in oversight of transportation projects that may affect ports. Private corporations may also play a role if they lease or own a terminal at a port.

An Investigation on the Effects of Ship Sourced Emissions in Izmir Port, Turkey

PubMed Central

Saraçoğlu, Halil; Kılıç, Alper

2013-01-01

Maritime transportation is a major source of climate change and air pollution. Shipping emissions cause severe impacts on health and environment. These effects of emissions are emerged especially in territorial waters, inland seas, canals, straits, bays, and port regions. In this paper, exhaust gas emissions from ships in Izmir Port, which is one of the main ports in Turkey, are calculated by the ship activity-based methodology. Total emissions from ships in the port is estimated as 1923 ton y−1 for NOx, 1405 ton y−1 for SO2, 82753 ton y−1 for CO2, ton y−1 for HC, and 165 ton y−1 for PM in the year 2007. These emissions are classified regarding operation modes and types of ships. The results are compared with the other studies including amounts of exhaust pollutants generated by ships. According to the findings, it is clear that the ships calling the Izmir Port are important air polluting causes of the Izmir city and its surroundings. PMID:24198720

A Chemical-Biological-Radio-Nuclear (CBRN) Filter can be Added to the Air-Outflow Port of a Ventilator to Protect a Home Ventilated Patient From Inhalation of Toxic Industrial Compounds.

PubMed

Be'eri, Eliezer; Owen, Simon; Beeri, Maurit; Millis, Scott R; Eisenkraft, Arik

2018-02-21

Chemical-biological-radio-nuclear (CBRN) gas masks are the standard means for protecting the general population from inhalation of toxic industrial compounds (TICs), for example after industrial accidents or terrorist attacks. However, such gas masks would not protect patients on home mechanical ventilation, as ventilator airflow would bypass the CBRN filter. We therefore evaluated in vivo the safety of adding a standard-issue CBRN filter to the air-outflow port of a home ventilator, as a method for providing TIC protection to such patients. Eight adult patients were included in the study. All had been on stable, chronic ventilation via a tracheostomy for at least 3 months before the study. Each patient was ventilated for a period of 1 hour with a standard-issue CBRN filter canister attached to the air-outflow port of their ventilator. Physiological and airflow measurements were made before, during, and after using the filter, and the patients reported their subjective sensation of ventilation continuously during the trial. For all patients, and throughout the entire study, no deterioration in any of the measured physiological parameters and no changes in measured airflow parameters were detected. All patients felt no subjective difference in the sensation of ventilation with the CBRN filter canister in situ, as compared with ventilation without it. This was true even for those patients who were breathing spontaneously and thus activating the ventilator's trigger/sensitivity function. No technical malfunctions of the ventilators occurred after addition of the CBRN filter canister to the air-outflow ports of the ventilators. A CBRN filter canister can be added to the air-outflow port of chronically ventilated patients, without causing an objective or subjective deterioration in the quality of the patients' mechanical ventilation. (Disaster Med Public Health Preparedness. 2018;page 1 of 5).

Terrorist Watchlist Checks and Air Passenger Prescreening

DTIC Science & Technology

2009-12-30

U.S. port of entry or at airport security checkpoints prior U.S. air carrier flights. For these purposes, CBP administers the Automated Targeting...Passenger Screening at Airport Security Checkpoints ................................. 14 9/11 Commission Recommendations and CAPPS II...individuals at either international ports of entries upon arrival at a U.S. port of entry or at airport security checkpoints prior U.S. air carrier

Ports Primer: 4.0 Port-Community Relations

EPA Pesticide Factsheets

Ports support and benefit local, regional and national economies through their role in creating jobs and transporting goods. The relationship between ports and near-port communities can be complex, as illustrated by case studies.

9 CFR 98.33 - Ports designated for the importation of certain animal semen.

Code of Federal Regulations, 2012 CFR

2012-01-01

...; Portland, Oregon; San Juan, Puerto Rico; Memphis, Tennessee; Galveston and Houston, Texas; Seattle, Spokane... designated for the importation of certain animal semen. (a) Air and ocean ports. The following air and ocean...

9 CFR 98.33 - Ports designated for the importation of certain animal semen.

Code of Federal Regulations, 2013 CFR

2013-01-01

...; Portland, Oregon; San Juan, Puerto Rico; Memphis, Tennessee; Galveston and Houston, Texas; Seattle, Spokane... designated for the importation of certain animal semen. (a) Air and ocean ports. The following air and ocean...

9 CFR 98.33 - Ports designated for the importation of certain animal semen.

Code of Federal Regulations, 2014 CFR

2014-01-01

...; Portland, Oregon; San Juan, Puerto Rico; Memphis, Tennessee; Galveston and Houston, Texas; Seattle, Spokane... designated for the importation of certain animal semen. (a) Air and ocean ports. The following air and ocean...

40 CFR 1065.325 - Intake-flow calibration.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Section 1065.325 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS ENGINE-TESTING PROCEDURES Calibrations and Verifications Flow-Related Measurements § 1065.325 Intake-flow calibration. (a) Calibrate intake-air flow meters upon initial installation. Follow the...

78 FR 37878 - Deepwater Port License Application: Liberty Natural Gas LLC, Port Ambrose Deepwater Port

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-24

... License Application: Liberty Natural Gas LLC, Port Ambrose Deepwater Port AGENCY: Maritime Administration... Deepwater Port License Application. The application describes an offshore natural gas deepwater port... assistance such as sign language interpretation or other reasonable accommodation, please notify the USCG...

Spatial variations of particulate matter and air toxics in communities adjacent to the Port of Oakland.

PubMed

Fujita, Eric M; Campbell, David E; Arnott, W Patrick; Lau, Virginia; Martien, Philip T

2013-12-01

The Bay Area Air Quality Management District (BAAQMD) sponsored the West Oakland Monitoring Study (WOMS) to provide supplemental air quality monitoring that will be used by the BAAQMD to evaluate local-scale dispersion modeling of diesel emissions and other toxic air contaminants for the area within and around the Port of Oakland. The WOMS was conducted during two seasonal periods of 4 weeks in summer 2009 and winter 2009/2010. Monitoring data showed spatial patterns of pollutant concentrations that were generally consistent with proximity to vehicle traffic. Concentrations of directly emitted pollutants were highest on heavily traveled roads with consistently lower concentrations away from the roadways. Pollutants that have higher emission rates from diesel trucks (nitric oxide, black carbon) tended to exhibit sharper gradients than pollutants that are largely associated with gasoline vehicles, such as carbon monoxide and volatile organic compounds, including benzene, toluene, ethylbenzene, and xylenes (BTEX). BTEX concentrations in West Oakland were similar to those measured at the three air toxics monitoring network sites in the Bay Area (San Francisco, Fremont, and San Jose). Aldehyde levels were higher in Fremont and San Jose than in West Oakland, reflecting greater contributions from photo-oxidation of hydrocarbons downwind of the Bay Area. A 2005 modeling-based health risk assessment of diesel particulate matter concentrations is consistent with aerosol carbon concentrations measured during the WOMS after adjusting for recent mitigation measures and improved estimates of heavy-duty truck traffic volumes.

Rotary vane type IC engine with built-in scavenging air blower

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chang, V.

This patent describes a rotary internal combustion engine. This engine consists of: a housing assembly including three sections and having a single common power shaft, the three sections being integrally connected together and operatively connected together into a unitary self-contained engine, air and fuel mixture intake conduit means communicatively connected to a first of the three sections, means in the first section to perform admission and compression of the air and fuel mixture admitted from the conduit means, means to convey the compressed air and fuel mixture to a second of the three sections. A single internal partition wall meansmore » between the first and second sections, and the air and fuel mixture conveys means consisting of a port formed in the partition wall means. In the second section the compressed air is ignited with a fuel mixture and to permit expansion of the ignited air and fuel mixture to thereby furnish power strokes to the power shaft. In the second section for exhausting the gaseous products of combustion, air blower in the third of the three sections driven by the power shaft.« less

Developing the port of Belawan as a modern and international port

NASA Astrophysics Data System (ADS)

Many, N.

2018-03-01

This study discusses the processes of government to pass the port development plan in Indonesia with the Port of Belawan and its port expansion as the study case. The study uses a descriptive approach by reviewing and analyzing some of relevant literature as the sources. It also reviews and examines the port development theoretical concepts and models giving attention to the international hub port models resulted from the previous studies. The international hub port aspects assessed to be further applied and compared to the actual situation of the Port of Belawan. This process draws the conclusion on which concept and model the port classified, followed by some recommendations concerning the necessary actions to be taken. The results show that: (1) The port planning regulated in port master plan is the guideline and foundation to implement the port development; (2) Spatial and zoning plan regulations are very important in the preparation, planning, and implementation of port development; (3) It has not provided the necessary facilities and criteria of the global hub port model has not been met completely. The port is strategic to be completely developed as the regional hub port to compete with the major ports of neighboring countries. Eventually, this study requires further analysis to examine the economic feasibility of the Port of Belawan in more comprehensive way functioning as an international hub port along with the ongoing development of Kuala Tanjung Port to achieve its ultimate objectives, among other things, the port effectiveness, efficiency, and competitiveness.

Ports Primer: 2.0 The Role of Ports

EPA Pesticide Factsheets

Our nation’s ports are an important part of our national economy and intermodal transportation system. The port industry faces many challenges, many of which can also involve and affect near-port communities.

Port wine oxidation management: a multiparametric kinetic approach.

PubMed

Martins, Rui Costa; Monforte, Ana Rita; Silva Ferreira, António

2013-06-05

Port wine is a flagship fortified wine of Portugal, which undergoes a particularly long aging period, developing a dynamic sensory profile over time, responsible for several wine categories, which is dependent upon the type of aging (bottle or barrel). Therefore, the quality of the product is dependent upon the chemical mechanisms occurring during the aging process, such as oxidation or Maillard reactions. To attain the desired quality management, it is necessary to understand how technological parameters, such as temperature or oxygen exposure, affect the kinetics of the formation of key odorants, such as sotolon. There is a lack of information about the impact of the storage conditions (oxygen and temperature) on Port wine quality. In this study, the effect of these two parameters were investigated to increase the knowledge database concerning aging management of Port wines. It was found that sotolon formation is highly dependent upon oxygen and temperature. There is however a synergistic effect between these two parameters that could significantly increase the concentration. The kinetic parameters of oxygen, sotolon, and other compounds related to Port aging (cis- and trans-5-hydroxy-2-methyl-1,3-dioxan, 2-furfural, 5-hydroxy-methyl-furfural, and 5-methyl-furfural) are also reported. Kinetic models with Monte Carlo simulations, where the oxygen permeability dispersion and temperature are the parameters under evaluation, were applied. On the basis of the modeling predictions, it would seem that the temperature of a cellar would have a more significant impact on the Port wines stored in containers where the oxygen intake is higher (barrels) when compared to containers with low oxygen permeability (bottles using cork stoppers).

Assessment of Near-Source Air Pollution at a Fine Spatial ...

EPA Pesticide Factsheets

Mobile monitoring is an emerging strategy to characterize spatially and temporally variable air pollution in areas near sources. EPA’s Geospatial Monitoring of Air Pollution (GMAP) vehicle – an all-electric vehicle measuring real-time concentrations of particulate and gaseous pollutants – was used to map air pollution levels near the Port of Charleston in South Carolina. High-resolution monitoring was performed along driving routes near several port terminals and rail yard facilities, recording geospatial coordinates and concentrations of pollutants including black carbon, size-resolved particle count ranging from ultrafine to coarse (6 nm to 20 um), carbon monoxide, carbon dioxide, and nitrogen dioxide. Additionally, a portable meteorological station was used to characterize local conditions. The primary objective of this work is to characterize the impact of port facilities on local scale air quality. It is found that elevated concentration measurements of Black Carbon and PM correlate to periods of increased port activity and a significant elevation in concentration is observed downwind of ports. However, limitations in study design prevent a more complete analysis of the port effect. As such, we discuss the ways in which this study is limited and how future work could be improved. Mobile monitoring is an emerging strategy to characterize spatially and temporally variable air pollution in areas near sources. EPA’s Geospatial Monitoring of Air Pollut

Decreasing carbon monoxide in the diving air of artisanal fishermen in the Yucatán peninsula by separation of engine exhaust from compressor intake.

PubMed

Chin, Walter; Huchim-Lara, Oswaldo; Salas, Silvia

2016-01-01

Artisanal fishermen in the Yucatán Peninsula utilize hookah dive systems (HDS). The air compressors in these HDS are not filtered, and the intake is near the engine exhaust. This proximity allows carbon monoxide (CO) from the exhaust to directly enter the HDS volume tank and contaminate the fishermen diver's air supply. Conservative safety standards permit a diver's air supply to contain 10 parts per million (ppm) of CO. This study quantified the levels of CO in the diver's air supply both before and after physical separation of the engine exhaust from the compressor intake. CO levels in seven volume tanks were analyzed before and after a 1-inch hose was attached to the compressor intake and elevated 5 feet above the engine exhaust. The tanks were drained and refilled before collecting each set of pre- and post-intervention gas samples. Four CO measurements were collected before and after the intervention from each volume tank. A C-Squared© CO Analyzer (± 1 ppm), calibrated with a Praxair 70 ppm CON2 gas (± 5%), was used to analyze the gas samples. A paired samples t-test shows a statistically significant difference in average CO values before and after the intervention (t = 6.8674, df: 27; p⟨0.0001). The physical separation of the engine exhaust from the compressor intake reduced the CO contamination of the diver air supply by 72%. This intervention could be applied to the hookah systems in the rest of the fishing cooperative to reduce the divers' risk of CO poisoning. Copyright© Undersea and Hyperbaric Medical Society.

Optimal application of the Contura multilumen balloon breast brachytherapy catheter vacuum port to deliver accelerated partial breast irradiation.

PubMed

Tokita, Kenneth M; Cuttino, Laurie W; Vicini, Frank A; Arthur, Douglas W; Todor, Dorin A; Julian, Thomas B; Lyden, Maureen R

2011-01-01

The impact of using the Contura multilumen balloon (MLB) (SenoRx, Inc., Irvine, CA) breast brachytherapy catheter's vacuum port in patients treated with accelerated partial breast irradiation (APBI) was analyzed. Data from 32 patients at two sites were reviewed. Variables analyzed included the seroma fluid (SF):air volume around the MLB before and after vacuum port use and on its ability to improve (1) the eligibility of patients for APBI and (2) dose coverage of the planning target volume for evaluation (PTV_EVAL) in eligible patients. The median SF/air volume before vacuum removal was 6.8 cc vs. 0.8 cc after vacuum removal (median reduction in SF/air volume was 90.5%). Before vacuum port use, the median SF/air volume expressed as percentage of the PTV_EVAL was 7.8% (range, 1.9-26.6) in all patients. After application of the vacuum, this was reduced to 1.2%. Before vacuum port use, 10 (31.3%) patients were not considered acceptable candidates for APBI because the SF/air volume:PTV_EVAL ratio (SF:PTV) was greater than 10% (range, 10.1-26.6%; median, 15.2%). After vacuum port use, the median SF:PTV ratio was 1.6% for a median reduction of 91.5%. In addition, the percentage of the prescribed dose covering greater than or equal to 90% of the PTV_EVAL proportionally increased a median of 8% (range, 3-10%) in eligible patients. Use of the Contura MLB vacuum port significantly improved the conformity of the target tissue to the balloon surface, leading to reproducible dose delivery and increased target volume coverage. In addition, application of the vacuum allowed the safe treatment of unacceptable patients with APBI. Copyright © 2011 American Brachytherapy Society. Published by Elsevier Inc. All rights reserved.

Is single port enough in minimally surgery for pneumothorax?

PubMed

Ocakcioglu, Ilhan; Alpay, Levent; Demir, Mine; Kiral, Hakan; Akyil, Mustafa; Dogruyol, Talha; Tezel, Cagatay; Baysungur, Volkan; Yalcinkaya, Irfan

2016-01-01

Video-assisted thoracoscopic surgery is a widespread used procedure for treatment of primary spontaneous pneumothorax patients. In this study, the adaptation of single-port video-assisted thoracoscopic surgery approach to primary spontaneous pneumothorax patients necessitating surgical treatment, with its pros and cons over the traditional two- or three-port approaches are examined. Between January 2011 and August 2013, 146 primary spontaneous pneumothorax patients suitable for surgical treatment are evaluated prospectively. Indications for surgery included prolonged air leak, recurrent pneumothorax, or abnormal findings on radiological examinations. Visual analog scale and patient satisfaction scale score were utilized. Forty triple-port, 69 double-port, and 37 single-port operations were performed. Mean age of 146 (126 male, 20 female) patients was 27.1 ± 16.4 (range 15-42). Mean operation duration was 63.59 ± 26 min; 61.7 for single, 64.2 for double, and 63.8 min for triple-port approaches. Total drainage was lower in the single-port group than the multi-port groups (P = 0.001). No conversion to open thoracotomy or 30-day hospital mortality was seen in our group. No recurrence was seen in single-port group on follow-up period. Visual analog scale scores on postoperative 24th, 48th, and 72nd hours were 3.42 ± 0.94, 2.46 ± 0.81, 1.96 ± 0.59 in the single-port group; significantly lower than the other groups (P = 0.011, P = 0.014, and P = 0.042, respectively). Patient satisfaction scale scores of patients in the single-port group on 24th and 48th hours were 1.90 ± 0.71 and 2.36 ± 0.62, respectively, indicating a significantly better score than the other two groups (P = 0.038 and P = 0.046). This study confirms the competency of single-port procedure in first-line surgical treatment of primary spontaneous pneumothorax.

Green Port / Eco Port Project - Applications and Procedures in Turkey

NASA Astrophysics Data System (ADS)

Akgul, Burak

2017-12-01

As being the heartlands of international trade, sea ports are the junction points of land and sea routes. The growth of global trade has led to the development of number and capacity as well as the service quality of ports. The policies and procedures applied during construction, operation and development of ports under development with environmental considerations scope has evolved in accordance with the needs of global trends. Although maritime transportation provides the most ecofriendly transportation method, the reduction of potential environmental threats and continuous improvement of ports and their vicinity is paramount from environmental concerns with regards to the international environmental standards. In the context of the study, national and international legal regulations governing the control of the environmental impacts of the activity groups causing pollution in Turkey based sea ports were viewed. In addition, the models applied during the measurement and documentation of environmental impacts were investigated. The most important aspects in terms of the effectiveness of the environmental management models are legal regulations. However, the standards applied at the ports without any legal obligation, such as EcoPorts applications, ISO 14001 standard, and the EMAS (Eco-Management and Audit Scheme) were sought in the scope of the study. The boundaries of the study were determined as the EU based Environmental Management Systems and the Green Port/Eco Port Project which is being administered by the Turkish Ministry of Transport, Maritime and Communication. “Marport”, which is Turkey’s first certified Green Port / Eco Port is designated as the experimental study site. In addition, the provisions in the ports of ESPO member countries are approached in order to compare the effectiveness and applicability of Green Port / Eco Port Project.

Multi-port valve

DOEpatents

Lewin, Keith F.

1997-04-15

A multi-port valve for regulating, as a function of ambient air having varying wind velocity and wind direction in an open-field control area, the distribution of a fluid, particularly carbon dioxide (CO.sub.2) gas, in a fluid distribution system so that the control area remains generally at an elevated fluid concentration or level of said fluid. The multi-port valve generally includes a multi-port housing having a plurality of outlets therethrough disposed in a first pattern of outlets and at least one second pattern of outlets, and a movable plate having a plurality of apertures extending therethrough disposed in a first pattern of apertures and at least one second pattern of apertures. The first pattern of apertures being alignable with the first pattern of outlets and the at least one second pattern of apertures being alignable with the second pattern of outlets. The first pattern of apertures has a predetermined orientation with the at least one second pattern of apertures. For an open-field control area subject to ambient wind having a low velocity from any direction, the movable plate is positioned to equally distribute the supply of fluid in a fluid distribution system to the open-field control area. For an open-field control area subject to ambient wind having a high velocity from a given direction, the movable plate is positioned to generally distribute a supply of fluid in a fluid distribution system to that portion of the open-field control area located upwind.

Multi-port valve

DOEpatents

Lewin, K.F.

1997-04-15

A multi-port valve is described for regulating, as a function of ambient air having varying wind velocity and wind direction in an open-field control area, the distribution of a fluid, particularly carbon dioxide (CO{sub 2}) gas, in a fluid distribution system so that the control area remains generally at an elevated fluid concentration or level of said fluid. The multi-port valve generally includes a multi-port housing having a plurality of outlets there through disposed in a first pattern of outlets and at least one second pattern of outlets, and a movable plate having a plurality of apertures extending there through disposed in a first pattern of apertures and at least one second pattern of apertures. The first pattern of apertures being alignable with the first pattern of outlets and the at least one second pattern of apertures being alignable with the second pattern of outlets. The first pattern of apertures has a predetermined orientation with the at least one second pattern of apertures. For an open-field control area subject to ambient wind having a low velocity from any direction, the movable plate is positioned to equally distribute the supply of fluid in a fluid distribution system to the open-field control area. For an open-field control area subject to ambient wind having a high velocity from a given direction, the movable plate is positioned to generally distribute a supply of fluid in a fluid distribution system to that portion of the open-field control area located upwind. 7 figs.

19 CFR 122.117 - Requirements for transit air cargo transport.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false Requirements for transit air cargo transport. 122... Requirements for transit air cargo transport. (a) Transportation—(1) Port to port. Transit air cargo may be... cargo, a receipt shall be given. The receipt shall be made by the airline responsible for transport or...

19 CFR 122.117 - Requirements for transit air cargo transport.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 19 Customs Duties 1 2011-04-01 2011-04-01 false Requirements for transit air cargo transport. 122... Requirements for transit air cargo transport. (a) Transportation—(1) Port to port. Transit air cargo may be... cargo, a receipt shall be given. The receipt shall be made by the airline responsible for transport or...

Two-port laparoscopic appendectomy assisted with needle grasper comparison with conventional laparoscopic appendectomy.

PubMed

Donmez, Turgut; Hut, Adnan; Avaroglu, Huseyin; Uzman, Sinan; Yildirim, Dogan; Ferahman, Sina; Cekic, Erdinc

2016-08-01

The 2-port laparoscopic appendectomy technique (TLA) is between the conventional 3-port and single-port laparoscopic appendectomy surgeries. We compared postoperative pain and cosmetic results after TLA with conventional laparoscopic appendectomy (CLA) by a 3-port device. Patients undergoing TLA were matched with patients undergoing CLA between February 2015 and November 2015 at the same institution. Thirty-two patients underwent TLA with a needle grasper. The appendix was secured by a percutaneous organ-holding device (needle grasper), then removed through a puncture at McBurney's point. Another 38 patients underwent CLA. Patient demographics, operative details, and postoperative outcomes were collected and evaluated. One patient in the TLA group developed a wound infection and 1 patient in the CLA group developed a postoperative intra-abdominal abscess and 3 wound infections. There was no significant difference between the groups when comparing the length of hospital stay, time until oral intake, and other complications. The pain score in the first 12 hours after surgery was significanly higher in CLA group than the TLA group (P < 0.001). Operative time was significantly shorter in the CLA group compared to the TLA group (P < 0.001). TLA using a needle grasper was associated with a significantly lower pain score 12 hours after surgery, better cosmetic results, and lower cost, than the CLA 3-port procedure because of the fewer number of ports.

41. #1 ARRESTING GEAR ENGINE AFT LOOKING FORWARD PORT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

41. #1 ARRESTING GEAR ENGINE - AFT LOOKING FORWARD PORT TO STARBOARD SHOWING ARRESTING GEAR ENGINE ACCUMULATOR, AIR FLASK, CONTROL VALVE, WITH CONTROL RAM, SHEAVES AND WIRES UNDERNEATH ENGINE STAND. - U.S.S. HORNET, Puget Sound Naval Shipyard, Sinclair Inlet, Bremerton, Kitsap County, WA

PORT II

NASA Technical Reports Server (NTRS)

Muniz, Beau

2009-01-01

One unique project that the Prototype lab worked on was PORT I (Post-landing Orion Recovery Test). PORT is designed to test and develop the system and components needed to recover the Orion capsule once it splashes down in the ocean. PORT II is designated as a follow up to PORT I that will utilize a mock up pressure vessel that is spatially compar able to the final Orion capsule.

Characterization of the near-source population around five candidate ports on the Eastern Seaboard and Gulf Coast using a multi-modal freight transport perspective

EPA Science Inventory

Many ports are currently preparing for increased freight traffic, which may result in elevated local air pollution in areas near the port and freight transportation corridors. In this study, a geographical information system (GIS) analysis of areas surrounding five ports – Port o...

Air velocity distributions inside tree canopies from a variable-rate air-assisted sprayer

USDA-ARS?s Scientific Manuscript database

A variable-rate, air assisted, five-port sprayer had been in development to achieve variable discharge rates of both liquid and air. To verify the variable air rate capability by changing the fan inlet diameter of the sprayer, air jet velocities impeded by plant canopies were measured at various loc...

Shore Power for Vessels Calling at U.S. Ports: Benefits and Costs.

PubMed

Vaishnav, Parth; Fischbeck, Paul S; Morgan, M Granger; Corbett, James J

2016-02-02

When in port, ships burn marine diesel in on-board generators to produce electricity and are significant contributors to poor local and regional air quality. Supplying ships with grid electricity can reduce these emissions. We use two integrated assessment models to quantify the benefits of reducing the emissions of NOX, SO2, PM2.5, and CO2 that would occur if shore power were used. Using historical vessel call data, we identify combinations of vessels and berths at U.S. ports that could be switched to shore power to yield the largest gains for society. Our results indicate that, depending on the social costs of pollution assumed, an air quality benefit of $70-150 million per year could be achieved by retrofitting a quarter to two-thirds of all vessels that call at U.S. ports. Such a benefit could be produced at no net cost to society (health and environmental benefits would be balanced by the cost of ship and port retrofit) but would require many ships to be equipped to receive shore power, even if doing so would result in a private loss for the operator. Policy makers could produce a net societal gain by implementing incentives and mandates to encourage a shift toward shore power.

Ports Primer: 4.1 Port Impacts to Local Communities

EPA Pesticide Factsheets

State and local governments are important players in port governance and in oversight of transportation projects that may affect ports. Private corporations may also play a role if they lease or own a terminal at a port.

Design and evaluation of candidate pressure ports for the HYFLITE experiment

NASA Technical Reports Server (NTRS)

Teter, John E., Jr.; Cleckner, Craig S.; Vontheumer, Alfred E.

1994-01-01

A concept for placing a pressure transducer directly in a shuttle type tile was developed at Langley Research Center. A 5 inch long quartz with a .020 inch inner diameter provides the thermal isolation necessary to allow 2800 F surface pressure measurements to be taken by pressure transducer rated at 250 F. The assembly is potted in place with RTV 560 in a piece of FRCI-12 thermal protection system insulation tile. The integrity of the thermal protection system is maintained even with the intrusion of the pressure port assembly and the pressure port does not disrupt the air flow across the lifting body. Approximately 200 of these pressure ports are to be used in each of the Hypersonic Flight Experiment (HYFLITE) flight tests. Initial vibroacoustic and aerothermal testing of the pressure port designs have been completed at Langley Research vibration laboratory and the 20 MWatt 2 x 9 turbulent duct facility at Ames Research Center. The performance of the pressure ports were found to be well within the required design limits for all cases. In addition, a failure mode in which the entire pressure port assembly was removed proved to be a begin case.

EPA and Port Everglades Partnership: Emission Inventories and Reduction Strategies

EPA Pesticide Factsheets

EPA’s Office of Transportation and Air Quality and Port Everglades announced a voluntary partnership to study mobile source emissions. Through this partnership, EPA and PEV agreed to work together to develop baseline and future year emission inventories.

33 CFR 165.760 - Security Zones; Tampa Bay, Port of Tampa, Port of Saint Petersburg, Port Manatee, Rattlesnake...

Code of Federal Regulations, 2011 CFR

2011-07-01

... of Tampa, Port of Saint Petersburg, Port Manatee, Rattlesnake, Old Port Tampa, Big Bend, Weedon..., Old Port Tampa, Big Bend, Weedon Island, and Crystal River, Florida. (a) Location. The following areas, denoted by coordinates fixed using the North American Datum of 1983 (World Geodetic System 1984), are...

33 CFR 165.760 - Security Zones; Tampa Bay, Port of Tampa, Port of Saint Petersburg, Port Manatee, Rattlesnake...

Code of Federal Regulations, 2010 CFR

2010-07-01

... of Tampa, Port of Saint Petersburg, Port Manatee, Rattlesnake, Old Port Tampa, Big Bend, Weedon..., Old Port Tampa, Big Bend, Weedon Island, and Crystal River, Florida. (a) Location. The following areas, denoted by coordinates fixed using the North American Datum of 1983 (World Geodetic System 1984), are...

33 CFR 165.760 - Security Zones; Tampa Bay, Port of Tampa, Port of Saint Petersburg, Port Manatee, Rattlesnake...

Code of Federal Regulations, 2013 CFR

2013-07-01

... of Tampa, Port of Saint Petersburg, Port Manatee, Rattlesnake, Old Port Tampa, Big Bend, Weedon..., Old Port Tampa, Big Bend, Weedon Island, and Crystal River, Florida. (a) Location. The following areas, denoted by coordinates fixed using the North American Datum of 1983 (World Geodetic System 1984), are...

33 CFR 165.760 - Security Zones; Tampa Bay, Port of Tampa, Port of Saint Petersburg, Port Manatee, Rattlesnake...

Code of Federal Regulations, 2014 CFR

2014-07-01

... of Tampa, Port of Saint Petersburg, Port Manatee, Rattlesnake, Old Port Tampa, Big Bend, Weedon..., Old Port Tampa, Big Bend, Weedon Island, and Crystal River, Florida. (a) Location. The following areas, denoted by coordinates fixed using the North American Datum of 1983 (World Geodetic System 1984), are...

33 CFR 165.760 - Security Zones; Tampa Bay, Port of Tampa, Port of Saint Petersburg, Port Manatee, Rattlesnake...

Code of Federal Regulations, 2012 CFR

2012-07-01

... of Tampa, Port of Saint Petersburg, Port Manatee, Rattlesnake, Old Port Tampa, Big Bend, Weedon..., Old Port Tampa, Big Bend, Weedon Island, and Crystal River, Florida. (a) Location. The following areas, denoted by coordinates fixed using the North American Datum of 1983 (World Geodetic System 1984), are...

Fewer-than-four ports versus four ports for laparoscopic cholecystectomy.

PubMed

Gurusamy, Kurinchi Selvan; Vaughan, Jessica; Rossi, Michele; Davidson, Brian R

2014-02-20

Traditionally, laparoscopic cholecystectomy is performed using two 10-mm ports and two 5-mm ports. Recently, a reduction in the number of ports has been suggested as a modification of the standard technique with a view to decreasing pain and improving cosmesis. The safety and effectiveness of using fewer-than-four ports has not yet been established. To assess the benefits (such as improvement in cosmesis and earlier return to activity) and harms (such as increased complications) of using fewer-than-four ports (fewer-than-four-ports laparoscopic cholecystectomy) versus four ports in people undergoing laparoscopic cholecystectomy for any reason (symptomatic gallstones, acalculous cholecystitis, gallbladder polyp, or any other condition). We searched the Cochrane Central Register of Controlled Trials (CENTRAL; Issue 8, 2013), MEDLINE, EMBASE, Science Citation Index Expanded, and the World Health Organization International Clinical Trials Registry Platform portal to September 2013. We included all randomised clinical trials comparing fewer-than-four ports versus four ports, that is, with standard laparoscopic cholecystectomy that is performed with two ports of at least 10-mm incision and two ports of at least 5-mm incision. Two review authors independently identified the trials and extracted the data. We analysed the data using both the fixed-effect and the random-effects models. For each outcome, we calculated the risk ratio (RR) or mean difference (MD) with 95% confidence intervals (CI) based on intention-to-treat analysis, whenever possible. We found nine trials with 855 participants that randomised participants to fewer-than-four-ports laparoscopic cholecystectomy (n = 427) versus four-port laparoscopic cholecystectomy (n = 428). Most trials included low anaesthetic risk participants undergoing elective laparoscopic cholecystectomy. Seven of the nine trials used a single port laparoscopic cholecystectomy and the remaining two trials used three-port laparoscopic

Assessment of near-source air pollution at a fine spatial scale ...

EPA Pesticide Factsheets

Mobile monitoring is an emerging strategy to characterize spatially and temporally variable air pollution in areas near sources. EPA’s Geospatial Monitoring of Air Pollution (GMAP) vehicle, an all-electric vehicle measuring real-time concentrations of particulate and gaseous pollutants, was utilized to map air pollution trends near the Port of Charleston in South Carolina. High-resolution monitoring was performed along driving routes near several port terminals and rail yard facilities, recording geospatial coordinates and measurements of pollutants including black carbon, size-resolved particle count ranging from ultrafine to coarse (6 nm to 20 µm), carbon monoxide, carbon dioxide, and nitrogen dioxide. Additionally, a portable meteorological station was used to characterize local meteorology. Port activity data was provided by the Port Authority of Charleston and includes counts of ships and trucks, and port service operations such as cranes and forklifts during the sampling time periods. Measurements are supplemented with modeling performed with AERMOD and RLINE in order to characterize the impact of the various terminals at the Port of Charleston on local air quality. Specifically, the data are used to determine the magnitude of the increase in local, near-port pollutant concentrations as well as the spatial extent to which concentration is elevated above background. These effects are studied in relation to a number of potentially significant factors such

Analysis of long-term, high time-resolution measurement of gaseous and particulate pollution near the Port of New York and New Jersey

EPA Science Inventory

The Port of New York and New Jersey is one of the largest and busiest ports in the United States and is located in close proximity to densely populated communities. To understand the local air quality impact of pollutant emission reduction activities at the port – including swit...

30 CFR 36.23 - Engine intake system.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Engine intake system. 36.23 Section 36.23... EQUIPMENT Construction and Design Requirements § 36.23 Engine intake system. (a) Construction. The intake... operator's compartment, to shut off the air supply to the engine. This valve shall be constructed to permit...

30 CFR 36.23 - Engine intake system.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Engine intake system. 36.23 Section 36.23... EQUIPMENT Construction and Design Requirements § 36.23 Engine intake system. (a) Construction. The intake... operator's compartment, to shut off the air supply to the engine. This valve shall be constructed to permit...

Enclosed rotary disc air pulser

DOEpatents

Olson, A. L.; Batcheller, Tom A.; Rindfleisch, J. A.; Morgan, John M.

1989-01-01

An enclosed rotary disc air pulser for use with a solvent extraction pulse olumn includes a housing having inlet, exhaust and pulse leg ports, a shaft mounted in the housing and adapted for axial rotation therein, first and second disc members secured to the shaft within the housing in spaced relation to each other to define a chamber therebetween, the chamber being in communication with the pulse leg port, the first disc member located adjacent the inlet port, the second disc member being located adjacent the exhaust port, each disc member having a milled out portion, the disc members positioned on the shaft so that as the shaft rotates, the milled out portions permit alternative cyclical communication between the inlet port and the chamber and the exhaust port and the chamber.

Near-Port Communities

EPA Pesticide Factsheets

Information to help near-port community leaders participate effectively in the decision-making process by increasing the understanding of the role of ports, how ports can impact local land use, economic trends, and environment.

Variable Cycle Intake for Reverse Core Engine

NASA Technical Reports Server (NTRS)

Chandler, Jesse M (Inventor); Staubach, Joseph B (Inventor); Suciu, Gabriel L (Inventor)

2016-01-01

A gas generator for a reverse core engine propulsion system has a variable cycle intake for the gas generator, which variable cycle intake includes a duct system. The duct system is configured for being selectively disposed in a first position and a second position, wherein free stream air is fed to the gas generator when in the first position, and fan stream air is fed to the gas generator when in the second position.

DOE ZERH Case Study: Clifton View Homes, Marine Drive and Port Hadlcok, Coupeville and Port Hadlock WA

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

2015-09-01

Case study of two DOE 2015 Housing Innovation Award winning custom homes in the marine climate that got HERS 39 and 38 without PV or HERS 2-12 and -9 with PV, with 6.5” SIP walls and 10.25” SIP roof; 11.75 ICF around slab, R-20 rigid foam under slab; radiant floor heat and passive design; air-to-water heatpump, fresh air intake with fan, triple-pane windows, 100% LED.

Ship emissions inventory, social cost and eco-efficiency in Shanghai Yangshan port

NASA Astrophysics Data System (ADS)

Song, Su

2014-01-01

This study estimated both the in-port ship emissions inventory (CO2, CH4, N2O, PM10, PM2.5, NOx, SOx, CO, and HC) and the emission associated social cost in Yangshan port of Shanghai. A sophisticated activity-based methodology, supported by the ship-by-ship and real-time data from the modern automatic identification system (AIS), was introduced to obtain accurate estimates of ship emissions. The detailed spatial and temporal emission inventories can be used as input for air quality dispersion modeling in the port and vicinities. The social cost of the emission impact on the Yangshan port coastal regions was then assessed based on the emissions inventories. The social cost covers the impact on human health, the environment, and the climate of the coastal community. Finally, the ship emissions was combined with port's basic operation profiles, i.e. container throughput, ship calls, and port revenue, in an attempt to assess the port's “eco-efficiency”, which indicates the port performance with social-economic and environmental concerns. This study filled the gap of previous studies by providing the AIS-supported activity-based emission inventory to facilitate the social cost-benefit analysis for the emission abatement policies. The result shows that i) the amount of in-port ship emissions of CO2, CH4, N2O, PM10, PM2.5, NOx, SOx, CO, and HC in Yangshan port area was 578,444 tons, 10 tons, 33 tons, 1078 tons (PM10, inducing PM2.5), 859 tons (PM2.5 only), 10,758 tons, 5623 tons, 1136 tons, and 519 tons, respectively, with ii) a total social cost of 287 million; iii) the values of the three parameters of the port eco-efficiency performance were 36,528 per 1,000 TEU throughput, 43,993 per ship call, and 44 million per billion US$ port revenue (4.4% of port revenue), respectively in 2009.

Sea-Air Intermodal Port Pair Selection Criteria in South America

DTIC Science & Technology

2011-06-01

the successes and lessons learned in operations since 2006. The researcher chose to consider this more recent timeframe as it revealed a marked...the US was experienced in the technique, once again it was a 11 hard lesson learned after years at war for TRANSCOM to switch to “smart” intermodal...current form, the TRANSCOM suitability model may be more informative for planning by incorporating criteria for port pair reliability. The paper

Assessment of shipping emissions on four ports of Portugal.

PubMed

Nunes, R A O; Alvim-Ferraz, M C M; Martins, F G; Sousa, S I V

2017-12-01

In the last few years, ship emissions have attracted growing attention in the scientific community. The main reason is the constant increase of marine emissions over the last twenty years due to the intensification of port traffic. Thus, this study aimed to evaluate ship emissions (PM 10 , PM 2.5 , NO x , SO 2 , CO, CO 2 , N 2 O CH 4 , NMVOC, and HC) through the activity-based methodology in four of the main ports of Portugal (Leixões, Setúbal, Sines and Viana do Castelo) during 2013 and 2014. The analysis was performed according to ship types (bulk carrier, container, general cargo, passenger, Ro-Ro cargo, tanker and others) and operational modes (manoeuvring, hotelling and during cruising). Results indicated that tankers were the largest emitters in two of the four analysed ports. Regarding cruising emissions, container ships were the largest emitters. . CO 2 , NO x and SO 2 estimated emissions represented more than 95% of the cruising and in-port emissions. Results were also compared with the total national emissions reported by the Portuguese Environment Agency, and if the in-port emissions estimated in the present study would have been taken into account to these totals, emissions of NO x and SO 2 would increase 15% and 24% in 2013 and 16% and 28% in 2014. Summing up ships seem to be an important source of air pollution, mainly regarding NO x and SO 2 . Copyright © 2017 Elsevier Ltd. All rights reserved.

Two-Port Laparoscopic Descending Colostomy with Separated Stomas for Anorectal Malformations in Newborns.

PubMed

Gine, Carlos; Santiago, Saioa; Lara, Alba; Laín, Ana; Lane, Victoria Alison; Wood, Richard J; Levitt, Marc

2016-10-01

Introduction  We describe a two-port laparoscopic technique to create a colostomy in the descending colon with separated stomas for newborns with anorectal malformations. Material and Methods  Six patients with an anorectal malformation underwent this procedure in the early-neonatal period. The surgical technique was performed with two ports, which allows for an accurate inspection of the abdominal contents. The first loop of the sigmoid colon is grasped through the first port and exteriorized while the attachments to the left retroperitoneum and direction of the loop are checked with the scope introduced in the second port. The division of the colon is performed extracorporally, the colon irrigated of meconium, and the distal colon moved to the second port incision. Both stomas are then fixed to the abdominal wall. Results  The time of the procedure ranged from 50 to 90 minutes. A Mullerian duplication was noted in one case. Oral intake was started during the first 12 to 24 hours. No complications were seen during or after the procedure. Conclusions  This technique allows for the precise localization of the colostomy with direct visualization, provides for the inspection of the internal genitalia, eliminates the incision between the two stomas and its complications, allows for painless stoma bag changes immediately after surgery, avoids twisting of the colostomy, and permits a cosmetically pleasing incision at the colostomy closure. Georg Thieme Verlag KG Stuttgart · New York.

Usefulness of a Flexible Port for Natural Orifice Transluminal Endoscopic Surgery by the Transrectal and Transvaginal Routes

PubMed Central

Ohdaira, Takeshi; Ikeda, Keiichi; Tajiri, Hisao; Yasuda, Yoshikazu; Hashizume, Makoto

2010-01-01

We developed a flexible port for NOTES which allows the use of conventional forceps for laparoscope-assisted surgery without change. The port is not affected by the location of the through hole in the gastrointestinal tract or vagina which elicits a problem in conventional NOTES, and its length can be adjusted during surgery by cutting the port itself. The port is made of polymer resin with a low friction coefficient. Furthermore, the port walls have a square wave structure which contributes to (1) the prevention of devices, for example, endoscope, from getting stuck at the time of insertion and retrieval, (2) the prevention of port slippage in the surgical opening for port insertion, (3) the prevention of unexpected port removal, (4) the prevention of port bore deformation, and (5) the improvement of port flexibility in the longitudinal direction. We validated the insertion and retrieval capacities of commercially available forceps for laparoscope-assisted surgery and power devices. Furthermore, we used the flexible port to conduct cholecystectomy and partial gastrectomy. We could confirm that the selection of the flexible port diameter according to the device type allowed the smooth insertion and retrieval of the device and that the port produced no air leakage. We affirmed that it is possible to conduct surgery by the cross or parallel method similarly to single port surgery. We considered that the flexible port has a potential of becoming a revolutionary port in NOTES. PMID:20508827

Integrated circuit test-port architecture and method and apparatus of test-port generation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Teifel, John

A method and apparatus are provided for generating RTL code for a test-port interface of an integrated circuit. In an embodiment, a test-port table is provided as input data. A computer automatically parses the test-port table into data structures and analyzes it to determine input, output, local, and output-enable port names. The computer generates address-detect and test-enable logic constructed from combinational functions. The computer generates one-hot multiplexer logic for at least some of the output ports. The one-hot multiplexer logic for each port is generated so as to enable the port to toggle between data signals and test signals. Themore » computer then completes the generation of the RTL code.« less

Depth-discrete sampling port

DOEpatents

Pemberton, Bradley E [Aiken, SC; May, Christopher P [Columbia, MD; Rossabi, Joseph [Aiken, SC; Riha, Brian D [Augusta, GA; Nichols, Ralph L [North Augusta, SC

1998-07-07

A sampling port is provided which has threaded ends for incorporating the port into a length of subsurface pipe. The port defines an internal receptacle which is in communication with subsurface fluids through a series of fine filtering slits. The receptacle is in further communication through a bore with a fitting carrying a length of tubing there which samples are transported to the surface. Each port further defines an additional bore through which tubing, cables, or similar components of adjacent ports may pass.

Depth-discrete sampling port

DOEpatents

Pemberton, Bradley E.; May, Christopher P.; Rossabi, Joseph; Riha, Brian D.; Nichols, Ralph L.

1999-01-01

A sampling port is provided which has threaded ends for incorporating the port into a length of subsurface pipe. The port defines an internal receptacle which is in communication with subsurface fluids through a series of fine filtering slits. The receptacle is in further communication through a bore with a fitting carrying a length of tubing there which samples are transported to the surface. Each port further defines an additional bore through which tubing, cables, or similar components of adjacent ports may pass.

Guidelines for port authorities and governments on the privatization of port facilities

DOT National Transportation Integrated Search

1998-09-23

Definitions of privatization as there are port practitioners and experts. In these circumstances, drafting "Guidelines for Port Authorities and Governments on the privatization of port facilities" is a challenge. The ten-step approach presented in th...

78 FR 7672 - Approval and Promulgation of Implementation Plans; Texas; Beaumont/Port Arthur Ozone Maintenance...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-04

.... SUMMARY: EPA is approving a revision to the Beaumont/Port Arthur (BPA) 1997 8-hour ozone maintenance air... emissions model. The BPA 1997 8-hour ozone maintenance area consists of Hardin, Jefferson, and Orange... proposed to approve a revision to the BPA 1997 8-hour ozone maintenance air quality SIP by replacing the...

7 CFR 354.1 - Overtime work at border ports, sea ports, and airports.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 5 2011-01-01 2011-01-01 false Overtime work at border ports, sea ports, and airports. 354.1 Section 354.1 Agriculture Regulations of the Department of Agriculture (Continued) ANIMAL AND... EXPORTS; AND USER FEES § 354.1 Overtime work at border ports, sea ports, and airports. (a)(1) Any person...

7 CFR 354.1 - Overtime work at border ports, sea ports, and airports.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 5 2010-01-01 2010-01-01 false Overtime work at border ports, sea ports, and airports... EXPORTS; AND USER FEES § 354.1 Overtime work at border ports, sea ports, and airports. (a)(1) Any person... of aircraft at airports of entry or other places of inspection as a consequence of the operation of...

Effect of Intake Air Filter Condition on Vehicle Fuel Economy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Norman, Kevin M; Huff, Shean P; West, Brian H

2009-02-01

The U.S. Department of Energy (DOE) Office of Energy Efficiency and Renewable Energy and the U.S. Environmental Protection Agency (EPA) jointly maintain a fuel economy website (www.fueleconomy.gov), which helps fulfill their responsibility under the Energy Policy Act of 1992 to provide accurate fuel economy information [in miles per gallon (mpg)] to consumers. The site provides information on EPA fuel economy ratings for passenger cars and light trucks from 1985 to the present and other relevant information related to energy use such as alternative fuels and driving and vehicle maintenance tips. In recent years, fluctuations in the price of crude oilmore » and corresponding fluctuations in the price of gasoline and diesel fuels have renewed interest in vehicle fuel economy in the United States. (User sessions on the fuel economy website exceeded 20 million in 2008 compared to less than 5 million in 2004 and less than 1 million in 2001.) As a result of this renewed interest and the age of some of the references cited in the tips section of the website, DOE authorized the Oak Ridge National Laboratory (ORNL) Fuels, Engines, and Emissions Research Center (FEERC) to initiate studies to validate and improve these tips. This report documents a study aimed specifically at the effect of engine air filter condition on fuel economy. The goal of this study was to explore the effects of a clogged air filter on the fuel economy of vehicles operating over prescribed test cycles. Three newer vehicles (a 2007 Buick Lucerne, a 2006 Dodge Charger, and a 2003 Toyota Camry) and an older carbureted vehicle were tested. Results show that clogging the air filter has no significant effect on the fuel economy of the newer vehicles (all fuel injected with closed-loop control and one equipped with MDS). The engine control systems were able to maintain the desired AFR regardless of intake restrictions, and therefore fuel consumption was not increased. The carbureted engine did show a

33 CFR 165.809 - Security Zones; Port of Port Lavaca-Point Comfort, Point Comfort, TX and Port of Corpus Christi...

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) PORTS AND WATERWAYS SAFETY REGULATED NAVIGATION AREAS AND LIMITED ACCESS AREAS Specific Regulated Navigation Areas and Limited Access Areas Eighth Coast Guard District § 165.809 Security Zones; Port of Port...) Location. The following area is designated as a security zone: all waters of the Corpus Christi Inner...

9 CFR 97.1 - Overtime work at laboratories, border ports, ocean ports, and airports. 1

Code of Federal Regulations, 2011 CFR

2011-01-01

... 9 Animals and Animal Products 1 2011-01-01 2011-01-01 false Overtime work at laboratories, border ports, ocean ports, and airports. 1 97.1 Section 97.1 Animals and Animal Products ANIMAL AND PLANT... laboratories, border ports, ocean ports, and airports. 1 1 For designated ports of entry for certain animals...

9 CFR 97.1 - Overtime work at laboratories, border ports, ocean ports, and airports. 1

Code of Federal Regulations, 2014 CFR

2014-01-01

... 9 Animals and Animal Products 1 2014-01-01 2014-01-01 false Overtime work at laboratories, border ports, ocean ports, and airports. 1 97.1 Section 97.1 Animals and Animal Products ANIMAL AND PLANT... laboratories, border ports, ocean ports, and airports. 1 1 For designated ports of entry for certain animals...

9 CFR 97.1 - Overtime work at laboratories, border ports, ocean ports, and airports. 1

Code of Federal Regulations, 2013 CFR

2013-01-01

... 9 Animals and Animal Products 1 2013-01-01 2013-01-01 false Overtime work at laboratories, border ports, ocean ports, and airports. 1 97.1 Section 97.1 Animals and Animal Products ANIMAL AND PLANT... laboratories, border ports, ocean ports, and airports. 1 1 For designated ports of entry for certain animals...

78 FR 36014 - Deepwater Port License Application: Liberty Natural Gas, LLC, Port Ambrose Deepwater Port

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-14

... (NEPA) of 1969 (42 U.S.C. 4321 et seq.). The U.S. Environmental Protection Agency (EPA) and the U.S... Coastal State'' any coastal state which (A) would be directly connected by pipeline to a deepwater port as... the Designation of Adjacent Coastal States for Deepwater Port License Applications in the Federal...

Port Milwaukee

Science.gov Websites

Milwaukee Arts Board Historic Preservation Commission History of Milwaukee's City Hall Business and Port of Milwaukee Purchasing Division Judicial and Oversight Ethics Board Fire and Police Commission ) Deferred Compensation Plan Port of Milwaukee About Us Board of Harbor Commissioners History Directions to

Identification and selection of Environmental Performance Indicators for sustainable port development.

PubMed

Puig, Martí; Wooldridge, Chris; Darbra, Rosa Mari

2014-04-15

In this paper an identification and selection of Environmental Performance Indicators (EPIs) in port areas has been conducted. A comprehensive inventory of existing EPIs in use in the seaport sector has been identified for monitoring performance of operational (e.g. dust, noise, dredging, and waste), managerial (e.g. certification, compliance, and complaints) and environmental condition (e.g. air, water, sediment and ecosystems). These indicators have been filtered against specific criteria and have been assessed and evaluated by port stakeholders in order to obtain a final set of indicators suitable to be implemented at EU level. A user friendly tool has been developed specifically to assist port authorities in calculating and reporting the proposed indicators. This study has drawn on major research projects to blend academic research with input from marine professionals in order to identify, select, evaluate and validate EPIs that are acceptable and feasible to the sector, and practicable in their application and implementation. Copyright © 2014 Elsevier Ltd. All rights reserved.

23. CREW'S BERTHING, TOWARDS PORT, BUNKS ALONG PORT WALL, LOCKERS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

23. CREW'S BERTHING, TOWARDS PORT, BUNKS ALONG PORT WALL, LOCKERS LINE CROSS CORRIDOR. - U.S. Coast Guard Cutter WHITE LUPINE, U.S. Coast Guard Station Rockland, east end of Tillson Avenue, Rockland, Knox County, ME

51. Port elevation, in port. Note reduced turtle deck due ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

51. Port elevation, in port. Note reduced turtle deck due to quarters expansion. - U.S. Coast Guard Cutter WHITE SUMAC, U.S. Coast Guard 8th District Base, 4640 Urquhart Street, New Orleans, Orleans Parish, LA

Characterization of air profiles impeded by plant canopies for a variable-rate air-assisted sprayer

USDA-ARS?s Scientific Manuscript database

The preferential design for variable-rate orchard and nursery sprayers relies on tree structure to control liquid and air flow rates. Demand for this advanced feature has been incremental as the public demand on reduction of pesticide use. A variable-rate, air assisted, five-port sprayer had been in...

W-band six-port network analyzer for two-port characterization of millimeter wave transistors

NASA Technical Reports Server (NTRS)

Moeller, Karl J.; Schaffner, James H.; Fetterman, Harold R.

1989-01-01

A W-band (75-100 GHz) six-port junction network analyzer was constructed from commercially available descrete waveguide components and was used for the direct two-port S-parameter measurement of active three-terminal devices. A comparison between the six-port and a down-converter-type frequency extender for a conventional network analyzer revealed the superior performance of the six-port. The application of the six-port to characterize a 0.1-micron gate-length HEMT at W-band is described, and representative results are presented.

Inverse Flush Air Data System (FADS) for Real Time Simulations

NASA Astrophysics Data System (ADS)

Madhavanpillai, Jayakumar; Dhoaya, Jayanta; Balakrishnan, Vidya Saraswathi; Narayanan, Remesh; Chacko, Finitha Kallely; Narayanan, Shyam Mohan

2017-12-01

Flush Air Data Sensing System (FADS) forms a mission critical sub system in future reentry vehicles. FADS makes use of surface pressure measurements from the nose cap of the vehicle for deriving the air data parameters of the vehicle such as angle of attack, angle of sideslip, Mach number, etc. These parameters find use in the flight control and guidance systems, and also assist in the overall mission management. The FADS under consideration in this paper makes use of nine pressure ports located in the nose cap of a technology demonstrator vehicle. In flight, the air data parameters are obtained from the FADS estimation algorithm using the pressure data at the nine pressure ports. But, these pressure data will not be available, for testing the FADS package during ground simulation. So, an inverse software to FADS which estimates the pressure data at the pressure ports for a given flight condition is developed. These pressure data at the nine ports will go as input to the FADS package during ground simulation. The software is run to generate the pressure data for the descent phase trajectory of the technology demonstrator. This data is used again to generate the air data parameters from FADS algorithm. The computed results from FADS algorithm match well with the trajectory data.

Computational studies of an intake manifold for restricted engine application

NASA Astrophysics Data System (ADS)

Prasetyo, Bagus Dwi; Ubaidillah, Maharani, Elliza Tri; Setyohandoko, Gabriel; Idris, Muhammad Idzdihar

2018-02-01

The Formula Society of Automotive Engineer (FSAE) student competition is an international contest for a vehicle that entirely designed and built by students from various universities. The engine design in the Formula SAE competition has to comply a tight regulation. Concerning the engine intake line, an air restrictor of circular cross-section less than 20 mm must be fitted between the throttle valve and the engine inlet. The throat is aimed to limit the engine air flow rate as it strongly influences the volumetric efficiency and then the maximum power. This article focuses on the design of the engine intake system of the Bengawan FSAE team vehicle to optimize the engine power output and its stability. The performance of engine intake system is studied through computational fluid dynamics (CFD). The objective of CFD is to know the pressure, velocity, and airflow of the air intake manifold for the best performance of the engine. The three-dimensional drawing of the intake manifold was made, and CFD simulation was conducted using ANSYS FLUENT. Two models were studied. The result shows that the different design produces a different value of the velocity of airflow and the kind of flow type.

Multiple-port valve

DOEpatents

Doody, Thomas J.

1978-08-22

A multiple-port valve assembly is designed to direct flow from a primary conduit into any one of a plurality of secondary conduits as well as to direct a reverse flow. The valve includes two mating hemispherical sockets that rotatably receive a spherical valve plug. The valve plug is attached to the primary conduit and includes diverging passageways from that conduit to a plurality of ports. Each of the ports is alignable wih one or more of a plurality of secondary conduits fitted into one of the hemispherical sockets. The other hemispherical socket includes a slot for the primary conduit such that the conduit's motion along that slot with rotation of the spherical plug about various axes will position the valve-plug ports in respect to the secondary conduits.

Excessive iodine intake, water chemicals and endemic goitre in a Sudanese coastal area.

PubMed

Medani, Abdel Monim M H; Elnour, Abdelsalam A; Saeed, Amal M

2013-09-01

To study the associations between intakes of iodine and water chemicals and the thyroid gland status of schoolchildren living in the coastal city of Port Sudan. In our previous nationwide study on goitre, it was observed that the prevalence of goitre was high in Port Sudan city despite high urinary iodine excretion. A cross-sectional study including schoolchildren aged 6–12 years was designed. Measurements determined the prevalence of goitre, urinary iodine concentration and thiocyanate secretion in casual urine samples, serum levels of thyroxine, triiodothyronine, thyroid-stimulating hormone and thyroglobulin, as well as the levels of Cl⁻, F⁻, Ca²⁺, Mg²⁺ and total hardness of drinking water. Schoolchildren (n 654) aged 6–12 years. Port Sudan city is located at the western bank of the Red Sea. The city is surrounded by a mountainous area known as the Red Sea Hills. It is the main sea port in the Sudan, inhabited by ethnically and socio-economically heterogeneous populations. The prevalence of goitre in Port Sudan was 34.86% while the median urinary iodine concentration was 46,4μg/dl. Out of thirty-one pupils from Port Sudan, twenty-four (77.42 %) were found to have urinary iodine concentration greater than 30μg/dl and twelve (38.71 %) had different degrees of biochemical hypothyroidism. Excessive concentrations of Cl⁻, Ca²⁺, Mg²⁺ and water hardness (369.2, 116.48, 60.21 and 539.0mg/l, respectively) were detected in drinking water samples collected from Port Sudan that exceeded levels permitted by the WHO. The coastal city of Port Sudan is a goitre-endemic area. In contrast to other Sudanese cities in which endemic goitre is related to iodine deficiency, goitre in Port Sudan is associated with iodine excess. Water chemicals seemed to have no effects on thyroid status.

360 PORT MDA - A Strategy to Improve Port Security

DTIC Science & Technology

2006-09-01

Participating Agencies (After: Executive Briefing..........................27 Table 6. Designated Joint Operations Center Participants (From: SAFE...Investigations CGIP Coast Guard Intelligence Program CHOC Charleston Harbor Operations Center CIO Command Intelligence Officer CMT Combating Maritime... EXECUTIVE SUMMARY Ports are critical to our economy and national security. Key hubs in the international trade network, U.S. ports accounted for more than

ITER Port Interspace Pressure Calculations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carbajo, Juan J; Van Hove, Walter A

The ITER Vacuum Vessel (VV) is equipped with 54 access ports. Each of these ports has an opening in the bioshield that communicates with a dedicated port cell. During Tokamak operation, the bioshield opening must be closed with a concrete plug to shield the radiation coming from the plasma. This port plug separates the port cell into a Port Interspace (between VV closure lid and Port Plug) on the inner side and the Port Cell on the outer side. This paper presents calculations of pressures and temperatures in the ITER (Ref. 1) Port Interspace after a double-ended guillotine break (DEGB)more » of a pipe of the Tokamak Cooling Water System (TCWS) with high temperature water. It is assumed that this DEGB occurs during the worst possible conditions, which are during water baking operation, with water at a temperature of 523 K (250 C) and at a pressure of 4.4 MPa. These conditions are more severe than during normal Tokamak operation, with the water at 398 K (125 C) and 2 MPa. Two computer codes are employed in these calculations: RELAP5-3D Version 4.2.1 (Ref. 2) to calculate the blowdown releases from the pipe break, and MELCOR, Version 1.8.6 (Ref. 3) to calculate the pressures and temperatures in the Port Interspace. A sensitivity study has been performed to optimize some flow areas.« less

Near-source air pollution and mitigation strategies

EPA Science Inventory

Abstract. Local-scale air pollution impact is of concern for populations located in close proximity to transit sources, including highway, port, rail, and other areas of concentrated diesel emissions. Previous near-road air monitoring research has prompted the U.S. EPA to implem...

Protecting America's ports

DOT National Transportation Integrated Search

2003-06-12

This website presents the press kit which accompanied the announcement by U.S. Secretary of Homeland Security Tom Ridge at Port Elizabeth, New Jersey on June 12, 2003 of new port security initiatives and investments to provide increased international...

Tuned intake air inlet for a rotary engine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Corbett, W.D.; Sheaffer, B.L.

This patent describes, in a rotary internal combustion engine, an improved assembly for providing a balanced flow of combustion air to the fuel supply inlet. It comprises: a plenum chamber attached to the engine block, the plenum chamber including an air inlet adapted to receive air from the cooling air exit passage and an air outlet for the discharge of air; and an outlet conduit connecting the air outlet and the fuel supply inlet. The conduit disposed to partially surround the plenum chamber to provide a conduit length substantially greater than the distance from the cooling air exit passage totmore » he fuel supply inlet.« less

Reduced-form air quality modeling for community-scale ...

EPA Pesticide Factsheets

Transportation plays an important role in modern society, but its impact on air quality has been shown to have significant adverse effects on public health. Numerous reviews (HEI, CDC, WHO) summarizing findings of hundreds of studies conducted mainly in the last decade, conclude that exposures to traffic emissions near roads are a public health concern. The Community LINE Source Model (C-LINE) is a web-based model designed to inform the community user of local air quality impacts due to roadway vehicles in their region of interest using a simplified modeling approach. Reduced-form air quality modeling is a useful tool for examining what-if scenarios of changes in emissions, such as those due to changes in traffic volume, fleet mix, or vehicle speed. Examining various scenarios of air quality impacts in this way can identify potentially at-risk populations located near roadways, and the effects that a change in traffic activity may have on them. C-LINE computes dispersion of primary mobile source pollutants using meteorological conditions for the region of interest and computes air-quality concentrations corresponding to these selected conditions. C-LINE functionality has been expanded to model emissions from port-related activities (e.g. ships, trucks, cranes, etc.) in a reduced-form modeling system for local-scale near-port air quality analysis. This presentation describes the Community modeling tools C-LINE and C-PORT that are intended to be used by local gove

Investigation of the Intake of a Stationary Gas Turbine to Prevent Ice Formation

NASA Astrophysics Data System (ADS)

Tramposch, Andreas; Molnár, Vojtech; Ridzoň, František

2011-12-01

Repeated emergency shutdowns of a stationary gas turbine under conditions of sub-freezing temperatures and moist air have led to the suspicion that ice formation in the intake channel and compressor may be a contributing factor. To understand the reason, why the installed ice protection system is not effective, a numerical investigation of the intake channel with the installed hot air ice protection system has been performed. It is shown that mixing of hot air with cold outside air is incomplete, explaining the ice accretion.

Case Studies: Improving Environmental Performance and Economic Prosperity at Ports and in Near-Port Communities

EPA Pesticide Factsheets

Case Study links for improving environmental performance and economic prosperity at ports and in near-port communities. Case studies on equipment upgrades, jobs and benefits, land use and transportation, port-community engagement, and citizen science.

Port-wine stain

MedlinePlus

... Laser therapy is most successful in removing port-wine stains. It is the only method that can destroy the tiny blood vessels in the skin without causing much damage to the skin. The exact type ... on the person's age, skin type, and particular port-wine stain.

Assessment of Particulate Matter Levels in Vulnerable Communities in North Charleston, South Carolina prior to Port Expansion

PubMed Central

Svendsen, Erik R; Reynolds, Scott; Ogunsakin, Olalekan A; Williams, Edith M; Fraser-Rahim, Herb; Zhang, Hongmei; Wilson, Sacoby M

2014-01-01

INTRODUCTION The Port of Charleston, one of the busiest US ports, currently operates five terminals. The fifth terminal is being planned for expansion to accommodate container ships from the proposed Panama Canal expansion. Such expansion is expected to increase traffic within local vulnerable North Charleston neck communities by at least 7,000 diesel truck trips per day, more than a 70% increase from the present average rate of 10,000 trucks per day. Our objective was to measure the current particulate matter (PM) concentrations in North Charleston communities as a baseline to contrast against future air pollution after the proposed port expansion. METHODS Saturation study was performed to determine spatial variability of PM in local Charleston neck communities. In addition, the temporal trends in particulate air pollution within the region were determined across several decades. With the BGI sampler, PM samples were collected for 24 hours comparable to the federal reference method protocol. Gravimetric analysis of the PM filter samples was conducted following EPA protocol. RESULTS The range of the PM10 annual average across the region from 1982 to 2006 was 17.0–55.0 μg/m3. On only two occasions were the records of PM10 averaged above the 50.0 μg/m3 national standard. In the case of PM2.5, the annual average for 1999–2006 ranged from 11.0 to 13.5 μg/m3 and no annual average exceeded the 15.0 μg/m3 PM2.5 annual standard. CONCLUSIONS Although ambient PM levels have fallen in the Charleston region since the 1960s due to aggressive monitoring by the stakeholders against air pollution, local air pollution sources within the North Charleston neck communities have consistently contributed to the PM levels in the region for several decades. This baseline assessment of ambient PM will allow for comparisons with future assessments to ascertain the impact of the increased truck and port traffic on PM concentrations. PMID:24653648

Tuned intake air system for a rotary engine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Corbett, W.D.

This patent describes a rotary internal combustion engine for an outboard board motor. It comprises a plenum chamber attached to the rear of the engine; and the plenum chamber including an inner wall attached to the exhaust manifold; an inlet conduit connecting the cooling air exit passage and the inlet air opening; an outlet conduit connecting the outlet air opening and the combustion air inlet; and the outlet conduit terminating in a combustion air outlet in the inner wall of the plenum chamber.

78 FR 42587 - Deepwater Port License: Amendment of the Neptune LNG LLC Deepwater Port License and Temporary...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-16

... Neptune LNG LLC Deepwater Port License and Temporary Suspension of Operations at the Neptune LNG Deepwater... decision to approve the request of Neptune LNG LLC (Neptune) for a temporary five-year suspension of port operations at the Neptune Deepwater Port by amending the Neptune Deepwater Port License. ADDRESSES: The...

Maximizing port and transportation system productivity by exploring alternative port operation strategies.

DOT National Transportation Integrated Search

2011-06-01

Seaports are a critical transportation component that supports the nations economy. Many U.S. : ports are now experiencing significant truck congestion at the gate, which decreases the productivity of : ports and truck fleets (e.g. truck wait time...

Port Authority Best Practices

EPA Pesticide Factsheets

Best practices for port authorities include near-port community collaboration, anti-idling policies, expanding off-peak hours, development of EMS, developing an emissions inventory, education, electric power and substituting trucking for rail or barge.

Self port scanning tool : providing a more secure computing Environment through the use of proactive port scanning

NASA Technical Reports Server (NTRS)

Kocher, Joshua E; Gilliam, David P.

2005-01-01

Secure computing is a necessity in the hostile environment that the internet has become. Protection from nefarious individuals and organizations requires a solution that is more a methodology than a one time fix. One aspect of this methodology is having the knowledge of which network ports a computer has open to the world, These network ports are essentially the doorways from the internet into the computer. An assessment method which uses the nmap software to scan ports has been developed to aid System Administrators (SAs) with analysis of open ports on their system(s). Additionally, baselines for several operating systems have been developed so that SAs can compare their open ports to a baseline for a given operating system. Further, the tool is deployed on a website where SAs and Users can request a port scan of their computer. The results are then emailed to the requestor. This tool aids Users, SAs, and security professionals by providing an overall picture of what services are running, what ports are open, potential trojan programs or backdoors, and what ports can be closed.

Contamination of hospital compressed air with nitric oxide: unwitting replacement therapy.

PubMed

Pinsky, M R; Genc, F; Lee, K H; Delgado, E

1997-06-01

Inhaled nitric oxide (NO) at levels between 5 and 80 ppm has been used experimentally to treat a variety of conditions. NO also is a common environmental air pollutant in industrial regions. As compressed hospital air is drawn from the local environment, we speculated that it may contain NO contamination, which, if present, would provide unwitting inhaled NO therapy to all subjects respiring this compressed gas. NO levels were measured twice daily from ambient hospital air and compressed gas sources driving positive pressure ventilation from two adjacent hospitals and compared with NO levels reported daily by local Environmental Protection Agency sources. An NO chemiluminescence analyzer (Sievers 270B; Boulder, Colo) sensitive to > or =2 parts per billion was used to measure NO levels in ambient air and compressed gas. NO levels in ambient air and hospital compressed air covaried from day to day, and absolute levels of NO differed between hospitals with the difference never exceeding 1.4 ppm (range, 0 to 1.4 ppm; median, 0.07 ppm). The hospital with the highest usage level of compressed air had the highest levels of NO, which approximated ambient levels of NO. NO levels were lowest on weekends in both hospitals. We also documented inadvertent NO contamination in one hospital occurring over 5 days, which corresponded to welding activity near the intake port for fresh gas. This contamination resulted in system-wide NO levels of 5 to 8 ppm. Hospital compressed air contains highly variable levels of NO that tend to covary with ambient NO levels and to be highest when the rate of usage is high enough to preclude natural degradation of NO in 21% oxygen. Assuming that inhaled NO may alter gas exchange, pulmonary hemodynamics, and outcome from acute lung injury, the role of unwitting variable NO of hospital compressed air needs to be evaluated.

Flight-determined characteristics of an air intake system on an F-111A airplane

NASA Technical Reports Server (NTRS)

Hughes, D. L.; Johnson, H. J.

1972-01-01

Flow phenomena of the F-111A air intake system were investigated over a large range of Mach number, altitude, and angle of attack. Boundary-layer variations are shown for the fuselage splitter plate and inlet entrance stations. Inlet performance is shown in terms of pressure recovery, airflow, mass-flow ratio, turbulence factor, distortion factor, and power spectral density. The fuselage boundary layer was found to be not completely removed from the upper portion of the splitter plate at all Mach numbers investigated. Inlet boundary-layer ingestion started at approximately Mach 1.6 near the translating spike and cone. Pressure-recovery distribution at the compressor face showed increasing distortion with increasing angle of attack and increasing Mach number. The time-averaged distortion-factor value approached 1300, which is near the distortion tolerance of the engine at Mach numbers above 2.1.

46 CFR 171.116 - Port lights.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Port lights. 171.116 Section 171.116 Shipping COAST... Port lights. (a) A vessel may have port lights below the bulkhead deck if— (1) It is greater than 150 gross tons; and (2) It is in ocean service. (b) All port lights in a space must be non-opening if the...

46 CFR 171.116 - Port lights.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 7 2012-10-01 2012-10-01 false Port lights. 171.116 Section 171.116 Shipping COAST... Port lights. (a) A vessel may have port lights below the bulkhead deck if— (1) It is greater than 150 gross tons; and (2) It is in ocean service. (b) All port lights in a space must be non-opening if the...

46 CFR 171.116 - Port lights.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 7 2013-10-01 2013-10-01 false Port lights. 171.116 Section 171.116 Shipping COAST... Port lights. (a) A vessel may have port lights below the bulkhead deck if— (1) It is greater than 150 gross tons; and (2) It is in ocean service. (b) All port lights in a space must be non-opening if the...

46 CFR 171.116 - Port lights.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 7 2011-10-01 2011-10-01 false Port lights. 171.116 Section 171.116 Shipping COAST... Port lights. (a) A vessel may have port lights below the bulkhead deck if— (1) It is greater than 150 gross tons; and (2) It is in ocean service. (b) All port lights in a space must be non-opening if the...

46 CFR 171.116 - Port lights.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 7 2014-10-01 2014-10-01 false Port lights. 171.116 Section 171.116 Shipping COAST... Port lights. (a) A vessel may have port lights below the bulkhead deck if— (1) It is greater than 150 gross tons; and (2) It is in ocean service. (b) All port lights in a space must be non-opening if the...

Effect of port-care frequency on venous port catheter-related complications in cancer patients.

PubMed

Odabas, Hatice; Ozdemir, Nuriye Yıldırım; Ziraman, Ipek; Aksoy, Sercan; Abali, Huseyin; Oksuzoglu, Berna; Isik, Metin; Civelek, Burak; Dede, Dogan; Zengin, Nurullah

2014-08-01

Subcutaneous central venous port catheters (SCVPC) are of great importance in the treatment of patients with malignancies since they provide secure vascular access. Our aim was to assess the impact of long-term catheter care frequency on the frequency of port-related complications. Two hundred and seven patients who had not been on active chemotherapy through their SCVPC for at least 3 months were enrolled into the study. Those who received catheter care every 3 months or more frequently were assigned to the frequent care group, and the others to the infrequent care group. The patients were examined for port-related complications and thrombosis including port occlusion. Routinely in our clinic, catheter care was done by using 300 IU of heparin. According to the frequency of SCVPC care, 49 (23.7 %) patients were in the frequent care group and 158 (76.3 %) were in the infrequent care group. Median follow-up of all patients was 671 days (range 133-1712). Median frequency of port care in the frequent care group was 90 days (range 30-90), but 441.5 days in the infrequent care group (range 91-1630). None of the patients experienced port-related severe complications during the follow-up time. None of them presented with port occlusion. When the groups were analysed for thrombus (symptomatic and asymptomatic), there was no statistically significant difference (6.4 vs 13.8 %, p = 0.17). Those patients who had received more than first-line chemotherapy were found to have more thrombi than the patients who were treated with only one type of chemotherapy protocol (28.6 vs 10.2 %, p = 0.01), and the patients who had metastatic disease at the last control were found out to have thrombi more frequently than the non-metastatic patients (24.3 vs 9.3 %) (p = 0.01). In the present study, there was no difference in port-related severe complications between frequent and infrequent care groups during follow-up. However, the rate of thrombosis was slightly higher in the infrequent port

47 CFR 52.35 - Porting Intervals.

Code of Federal Regulations, 2014 CFR

2014-10-01

... “telecommunications carrier” includes an interconnected Voice over Internet Protocol (VoIP) provider as that term in... ports” includes (i) Wireline-to-wireless ports; (ii) Wireless-to-wireline ports; and (iii) Ports...

The Identification and Classification of Inland Ports

DOT National Transportation Integrated Search

2001-08-01

This report presents a formal definition for inland ports and creates a classification methodology to promote familiarity with inland port operations and aid transportation planners interested in supporting inland port operations. Inland ports are si...

77 FR 49351 - Safety Zone; Port Huron Float-Down, St. Clair River, Port Huron, MI

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-16

...-AA00 Safety Zone; Port Huron Float-Down, St. Clair River, Port Huron, MI AGENCY: Coast Guard, DHS. ACTION: Temporary final rule. SUMMARY: The Coast Guard is establishing a temporary safety zone on the St. Clair River, Port Huron, MI. This zone is intended to restrict vessels from a portion of the St. Clair...

Future anthropogenic pollutant emissions in a Mediterranean port city with emphasis on the maritime sector emissions - Study of the impact on the city air quality

NASA Astrophysics Data System (ADS)

Liora, Natalia; Poupkou, Anastasia; Markakis, Konstantinos; Giannaros, Theodoros; Karagiannidis, Athanasios; Melas, Dimitrios

2013-04-01

traffic changes as foreseen for the year 2020 by the Port Authority Investment Plan and by the reduction of the sulfur content in fuels used by ships in cruising mode to 0.5% m/m according to a revision of the MARPOL Annex VI. Based on the above, an approximately 60% increase in the future maritime sector PM10 emissions is expected due to the high increase of the traffic of vessels. The impact of future emissions on the air quality of Thessaloniki is examined with the use of the modelling system WRF-CAMx applied with 2km spatial resolution over the study area. Simulations of the modelling system are performed for a summertime (July 2011) and a wintertime (15 November to 15 December 2011) period accounting for present time (scenario A) and future time (scenario B) pollutant emissions. The differences in pollutant levels (mainly PM) between the scenarios examined are presented and discussed.

Shipping emissions and their impacts on air quality in China.

PubMed

Zhang, Yan; Yang, Xin; Brown, Richard; Yang, Liping; Morawska, Lidia; Ristovski, Zoran; Fu, Qingyan; Huang, Cheng

2017-03-01

China has >400 ports, is home to 7 of 10 biggest ports in the world and its waterway infrastructure construction has been accelerating over the past years. But the increasing number of ports and ships means increasing emissions, and in turn, increasing impact on local and regional air pollution. This paper presents an overview of the broad field of ship emissions in China and their atmospheric impacts, including topics of ship engine emissions and control, ship emission factors and their measurements, developing of ship emission inventories, shipping and port emissions of the main shipping areas in China, and quantitative contribution of shipping emissions to the local and regional air pollution. There have been an increasing number of studies published on all the above aspects, yet, this review identified some critical research gaps, filling of which is necessary for better control of ship emissions, and for lowering their impacts. In particular, there are very few studies on inland ports and river ships, and there are few national scale ship emission inventories available for China. While advanced method to estimate ship emission based on ship AIS activities makes it now possible to develop high spatial- and temporal-resolution emission inventories, the ship emission factors used in Chinese studies have been based mainly on foreign measurements. Further, the contribution of ship emissions to air pollution in coastal cities, the dispersion of pollution plumes emitted by ships, or the chemical evolution process along the transmission path, have so far not been systematically studied in China. Copyright © 2016 Elsevier B.V. All rights reserved.

Principles of subcutaneous port placement.

PubMed

Gonda, Shaun J; Li, Ruizong

2011-12-01

The introduction of totally implantable subcutaneous devices in the early 1980s provided patients with secure, reliable venous access and also gave them the ability to move more freely and have a more normal lifestyle with these devices in place. The most common totally implantable device used today is the subcutaneous port. These ports consist of an injection port connected to a catheter. Ports provide a number of advantages compared with other venous catheters; the most important is the reduced risk of infection. These devices have significantly lower rates of infection than nontunneled and tunneled catheters. Additional advantages include less frequent irrigation and minimal home care, and they are less prone to environmental or cutaneous contamination when not being accessed. This article will focus on the placement of these ports. Copyright © 2011 Elsevier Inc. All rights reserved.

47 CFR 52.35 - Porting Intervals.

Code of Federal Regulations, 2010 CFR

2010-10-01

... work week of Monday through Friday represents mandatory business days and 8 a.m. to 5 p.m. represents... ports” includes (i) Wireline-to-wireless ports; (ii) Wireless-to-wireline ports; and (iii) Ports...

47 CFR 52.35 - Porting Intervals.

Code of Federal Regulations, 2011 CFR

2011-10-01

... work week of Monday through Friday represents mandatory business days and 8 a.m. to 5 p.m. represents... ports” includes (i) Wireline-to-wireless ports; (ii) Wireless-to-wireline ports; and (iii) Ports...

Port of Davisville utilization study : phase II.

DOT National Transportation Integrated Search

2011-02-01

This project investigated the feasibility of expanding the Port of Davisville (Quonset Point, RI) to serve : as a port of entry and departure for international container shipments. As an international port of entry : (departure), the Port of Davisvil...

Dedicated EGR engine with dynamic load control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hayman, Alan W.; McAlpine, Robert S.; Keating, Edward J.

An internal combustion engine comprises a first engine bank and a second engine bank. A first intake valve is disposed in an intake port of a cylinder of the first engine bank, and is configured for metering the first flow of combustion air by periodically opening and closing according to a first intake valve lift and duration characteristic. A variable valve train control mechanism is configured for affecting the first intake valve lift and duration characteristic. Either a lift or duration of the first intake valve is modulated so as to satisfy an EGR control criterion.

A nuclear powered air cushion freighter for the 1980's.

NASA Technical Reports Server (NTRS)

Anderson, J. L.

1971-01-01

A design for a transoceanic, dry cargo-carrying freighter is suggested; its use and operation in port are discussed. With a gross weight of 4500 metric tons (5000 tons), more than 50 percent of which is cargo, it will cruise at 50 meters per second (100 knots) in waves 2.4 meters (8 ft) high. Its peripheral jet-flexible skirt air cushion concept and air thrustors will let the freighter go over waves 8 meters high at reduced velocity. Power comes from a 1280 megawatt, helium-cooled thermal reactor. It could dock at any major port in the world, but because it needs no surface contact, it could also travel inland to land-locked ports. A modular terminal design and methods of cargo transfer are suggested. The concept of cargo containerization influences both the freighter and terminal design.

Mississippi's industrial gulf ports

DOT National Transportation Integrated Search

2001-09-01

As a State, Mississippi ranked 20th in waterborne traffic in 1999, moving over 46 million short tons of commodities. Mississippi's port activities generate $38 million in state payroll taxes and $21 million in state sales taxes. Port and servicing in...

Sources and contamination rate of port sediments: evidences from dimensional, mineralogical, and chemical investigations

NASA Astrophysics Data System (ADS)

Lucchetti, Gabriella; Cutroneo, Laura; Carbone, Cristina; Consani, Sirio; Vagge, Greta; Canepa, Giuseppe; Capello, Marco

2017-04-01

Ports are complex environments due to their complicated geometry (quays, channels, and piers), the presence of human activities (vessel traffic, yards, industries, and discharges), and natural factors (stream and torrent inputs, sea action, and currents). Due to the many activities that take place in a port, sediments and waters are often contaminated by different kinds of chemicals, such as hydrocarbons, dioxins, pesticides, nutrients, and metals. The contamination rate of a port basin is site specific and depends on the sources of contamination in the nearby urban system as well as the port system itself, such as city discharges and sewers, river intake, vessel traffic, factories (Taylor and Owens, 2009). Moreover, two important sources and vehicles of contaminants are: a) anthropogenic road deposited sediments derived from the runoff of the port and city area, and natural road deposited sediments derived from rivers and torrents, and b) airborne particulate matter and sediments (Taylor and Owens, 2009). The Port of Genoa is situated at the apex of the Ligurian Sea in the north western Mediterranean Sea and is characterised by the presence of several commercial activities that have contributed, over the years, and still contribute today, to the contaminant accumulation in both the water column and the bottom sediments. This port basin includes the mouth of several streams and the mouth of the Bisagno and the Polcevera Torrents, along the banks of which can be found several small towns, quarries, factories, and the suburbs of the city of Genoa, a ferry terminal, different container terminals, marinas, dry docks, the coal power plant of Genoa, and different wastewater treatment plant discharges. Starting from these considerations, we have examined the marine environment of a port from the point of view of the water mass circulation, hydrological characteristics, distribution of the sediment grain size, mineralogical characteristics, and metal concentrations of the

A linear acoustic model for intake wave dynamics in IC engines

NASA Astrophysics Data System (ADS)

Harrison, M. F.; Stanev, P. T.

2004-01-01

In this paper, a linear acoustic model is described that has proven useful in obtaining a better understanding of the nature of acoustic wave dynamics in the intake system of an internal combustion (IC) engine. The model described has been developed alongside a set of measurements made on a Ricardo E6 single cylinder research engine. The simplified linear acoustic model reported here produces a calculation of the pressure time-history in the port of an IC engine that agrees fairly well with measured data obtained on the engine fitted with a simple intake system. The model has proved useful in identifying the role of pipe resonance in the intake process and has led to the development of a simple hypothesis to explain the structure of the intake pressure time history: the early stages of the intake process are governed by the instantaneous values of the piston velocity and the open area under the valve. Thereafter, resonant wave action dominates the process. The depth of the early depression caused by the moving piston governs the intensity of the wave action that follows. A pressure ratio across the valve that is favourable to inflow is maintained and maximized when the open period of the valve is such to allow at least, but no more than, one complete oscillation of the pressure at its resonant frequency to occur while the valve is open.

Towards participatory air pollution exposure assessment in a goods movement community

Treesearch

Michelle C. Kondo; Chris Mizes; John Lee; Jacqueline McGady-Saier; Lisa O' Malley; Ariel Diliberto; Igor Burstyn

2014-01-01

Air pollution from diesel truck traffic travelling to and from port facilities is a major environmental health concern in areas of Philadelphia such as the Port Richmond neighborhood. Ambient monitoring has limited capability to assess neighborhood- or personal-level exposures to this pollution. We sought to conduct a pilot study using a community-based participatory...

International Standardization in the Design of "Shore to Ship" - Power Supply Systems of Ships in Port

NASA Astrophysics Data System (ADS)

Tarnapowicz, Dariusz; German-Galkin, Sergiej

2018-03-01

The decisive source of air pollution emissions in ports is the berthed ships. This is primarily caused by the work of ship's autonomous generator sets. One way of reducing the air pollution emissions in ports is the supply of ships from electricity inland system. The main problem connected with the power connection of ships to the inland network is caused by different values of levels and frequencies of voltages in these networks (in various countries) in relation to different values of levels and frequencies of voltages present in the ship's network. It is also important that the source power can range from a few hundred kW up to several MW. In order to realize a universal „Shore to Ship" system that allows the connection of ships to the electricity inland network, the international standardization is necessary. This article presents the current recommendations, standards and regulations for the design of „Shore to Ship" systems.

Condensation heat transfer and pressure drop of R-410A in flat aluminum multi-port tubes

NASA Astrophysics Data System (ADS)

Kim, Nae-Hyun

2018-02-01

Brazed heat exchangers with aluminum flat multi-port tubes are being used as condensers of residential air-conditioners. In this study, R-410A condensation tests were conducted in four multi-port tubes having a range of hydraulic diameter (0.78 ≤ Dh ≤ 0.95 mm). The test range covered the mass flux from 100 to 400 kg/m2 s and the heat flux at 3 kW/m2, which are typical operating conditions of residential air conditioners. Results showed that both the heat transfer coefficient and the pressure drop increased as the hydraulic diameter decreased. The effect of hydraulic diameter on condensation heat transfer was much larger than the predictions of existing correlations for the range of investigation. Comparison of the data with the correlations showed that some macro-channel tube correlations and mini-channel tube correlations reasonably predicted the heat transfer coefficient. However, macro-channel correlations highly overpredicted the pressure drop data.

Near-Port Air Quality Assessment Utilizing a Mobile Monitoring Approach

EPA Science Inventory

Mobile monitoring is an emerging strategy to characterize spatially and temporally variable air pollution in areas near sources. EPA’s Geospatial Monitoring of Air Pollution (GMAP) vehicle – an all-electric vehicle measuring real-time concentrations of particulate and gaseous po...

22 CFR 120.24 - Port Directors.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 22 Foreign Relations 1 2013-04-01 2013-04-01 false Port Directors. 120.24 Section 120.24 Foreign Relations DEPARTMENT OF STATE INTERNATIONAL TRAFFIC IN ARMS REGULATIONS PURPOSE AND DEFINITIONS § 120.24 Port Directors. Port Directors of U.S. Customs and Border Protection means the U.S. Customs and Border...

22 CFR 120.24 - Port Directors.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 22 Foreign Relations 1 2011-04-01 2011-04-01 false Port Directors. 120.24 Section 120.24 Foreign Relations DEPARTMENT OF STATE INTERNATIONAL TRAFFIC IN ARMS REGULATIONS PURPOSE AND DEFINITIONS § 120.24 Port Directors. Port Directors of U.S. Customs and Border Protection means the U.S. Customs and Border...

22 CFR 120.24 - Port Directors.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 22 Foreign Relations 1 2014-04-01 2014-04-01 false Port Directors. 120.24 Section 120.24 Foreign Relations DEPARTMENT OF STATE INTERNATIONAL TRAFFIC IN ARMS REGULATIONS PURPOSE AND DEFINITIONS § 120.24 Port Directors. Port Directors of U.S. Customs and Border Protection means the U.S. Customs and Border...

22 CFR 120.24 - Port Directors.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 22 Foreign Relations 1 2012-04-01 2012-04-01 false Port Directors. 120.24 Section 120.24 Foreign Relations DEPARTMENT OF STATE INTERNATIONAL TRAFFIC IN ARMS REGULATIONS PURPOSE AND DEFINITIONS § 120.24 Port Directors. Port Directors of U.S. Customs and Border Protection means the U.S. Customs and Border...

22 CFR 120.24 - Port Directors.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Port Directors. 120.24 Section 120.24 Foreign Relations DEPARTMENT OF STATE INTERNATIONAL TRAFFIC IN ARMS REGULATIONS PURPOSE AND DEFINITIONS § 120.24 Port Directors. Port Directors of U.S. Customs and Border Protection means the U.S. Customs and Border...

Boosting devices with integral features for recirculating exhaust gas

DOEpatents

Wu, Ko -Jen

2015-09-15

According to one embodiment of the invention, a compressor housing includes a compressor inlet in fluid communication with a compressor volute configured to house a compressor wheel, the compressor inlet configured to provide a first air flow to the compressor wheel and a compressor outlet in fluid communication with the compressor volute, the compressor outlet configured to direct a compressed gas to an intake manifold. The compressor housing further includes an exhaust gas recirculation inlet port in fluid communication with the compressor volute, the exhaust gas recirculation inlet port being configured to combine an exhaust gas flow with the air flow to the compressor wheel.

Port Granby Project Overview - 13208

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, David W.; Vandergaast, Gary; Sungaila, Mark

2013-07-01

The Port Granby Project is an integral part of the Port Hope Area Initiative (PHAI), and is located approximately 14 kilometres west of the Municipality of Port Hope in the adjacent Municipality of Clarington, Ontario. The principal objective of the project is the excavation and relocation of low-level radioactive waste (LLRW) and marginally contaminated soils, which were deposited at the Port Granby Waste Management Facility (PGWMF) by Eldorado Nuclear Limited during the period 1955 to 1988, to a new, highly engineered above-ground Long-term Waste Management Facility (LTWMF) to be constructed on a nearby site. The Environmental Assessment for the Projectmore » was approved in 2009 August and the required Waste Nuclear Substance License was received in 2011 November. Once the detailed engineering design was completed, in 2011 March, the Port Granby Project was divided into three major contracts for construction implementation purposes. The first of these contracts was completed in late 2012 and the second is planned to start in early 2013. The contracting process for the third major contract is also expected to be completed during 2013. This paper provides an overview of the Port Granby Project as well as discussion on the status of the Project, including the regulatory approvals process, the approach to contracting the construction works and an update of work recently completed and soon to get underway. (authors)« less

78 FR 7336 - Safety Zone; Alaska Marine Highway System Port Valdez Ferry Terminal, Port Valdez; Valdez, AK

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-01

... 1625-AA00 Safety Zone; Alaska Marine Highway System Port Valdez Ferry Terminal, Port Valdez; Valdez, AK... Alaska Marine Highway System (AMHS) Port Valdez Ferry Terminal. The purpose of the safety zone is to... Security Delegation No. 0170.1. A representative of the Alaska Marine Highway System requested that the...

Laparoscopic Toupet Fundoplication using an Air Seal Intelligent Flow System and Anchor Port in a 1.8-kg infant: A Technical Report.

PubMed

Miyano, Go; Morita, Keiichi; Kaneshiro, Masakatsu; Miyake, Hiromu; Nouso, Hiroshi; Yamoto, Masaya; Koyama, Mariko; Nakano, Reiji; Tanaka, Yasuhiko; Fukumoto, Koji; Urushihara, Naoto

2015-08-01

We report a case of a 1.8-kg infant who had laparoscopic Toupet fundoplication (LTF) using the AirSeal Intelligent Flow System and Anchor Port (AP). Our case had severe gastroesophageal reflux in association with genetic and cardiac anomalies. Despite the patient being continuously fed, persistent vomiting caused failure to thrive, and LTF was performed at 4 months of age when he weighed 1.8 kg. The AirSeal Intelligent Flow System is a novel laparoscopic CO2 insufflation system that improves the visual field by constantly evacuating smoke and providing a more stable pneumoperitoneum. The AP is a recently developed, stretchable, elastomeric, low-profile cannula. Three 5-mm AP were inserted: one subumbilically for the scope and one in both the right and left upper abdomen for the surgeon. A 5-mm AirSeal trocar was inserted in the left lower abdomen for the assistant. The gastrosplenic ligament was dissected free, and the intra-abdominal esophagus was prepared. A posterior hiatoplasty was performed, followed by the 270° fundoplication. During the fundoplication, the esophagus was fixed to the crus and then the right and left wraps were fixed to the esophagus. Pneumoperitoneum was maintained stably throughout the LTF procedure, with optimal operative field. Total operating time for LTF was 90 min. Body temperature dropped from 37.4°C to 35.7°C during pneumoperitoneum but resolved once pneumoperitoneum was ceased. Postoperative progress was uneventful, and an upper gastrointestinal study on postoperative day 2 showed no residual gastroesophageal reflux. We believe the AirSeal Intelligent Flow System and AP contributed to the successful completion of LTF in a 1.8-kg infant. © 2015 Japan Society for Endoscopic Surgery, Asia Endosurgery Task Force and Wiley Publishing Asia Pty Ltd.

Scavenging a Piston-ported Two-stroke Cylinder

NASA Technical Reports Server (NTRS)

Rogowski, A R; Bouchard, C L

1938-01-01

An investigation was made with a specially designed engine to determine the scavenging characteristics of a large number of inlet-port shapes and arrangements and the optimum port arrangement and timing for this particular type of engine. A special cylinder construction permitted wide variations in timing for this particular type of engine. A special cylinder construction permitted wide variations in timing as well as in shape and arrangement of both the inlet and exhaust ports. The study of the effect of port shape combinations and timings on engine performance was made using illuminating gas as a fuel. Through variations in inlet-port arrangement and port timings, the value of the scavenging efficiency was increased from an original 44 percent to approximately 67 percent with a corresponding increase in power. With the optimum port arrangement and timing determined, a large number of performance runs were made under both spark-ignition and compression-ignition operation.

[Single-port laparoscopic cholecystectomy: advantages and disadvantages].

PubMed

Alekberzade, A V; Lipnitsky, E M; Krylov, N N; Sundukov, I V; Badalov, D A

2016-01-01

To analyze the outcomes of single-port laparoscopic cholecystectomy. Early and long-term postoperative period has been analyzed in 240 patients who underwent laparoscopic cholecystectomy (LCE) including 120 cases of single-port technique and 120 cases of four-port technique. Both groups were compared in surgical time, pain syndrome severity (visual analog scale), need for analgesics, postoperative complications, hospital-stay, daily activity recovery and return to physical work, patients' satisfaction of surgical results and their aesthetic effect. It was revealed that single-port LCE is associated with lower severity of postoperative pain, quick recovery of daily activity and return to physical work, high satisfaction of surgical results and their aesthetic effect compared with four-port LCE. Disadvantages of single-port LCE include longer duration of surgery, high incidence of postoperative umbilical hernia. However hernia was predominantly observed during the period of surgical technique development. Further studies to standardize, evaluate the safety and benefits of single-port LCE are necessary.

77 FR 47522 - Special Local Regulation; Port Huron Offshore Gran Prix, St. Clair River; Port Huron, MI

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-09

...-AA08 Special Local Regulation; Port Huron Offshore Gran Prix, St. Clair River; Port Huron, MI AGENCY... regulation on the St. Clair River, Port Huron, Michigan. This action is necessary and intended to ensure... movement of, vessels in a portion of the St. Clair River. During the enforcement period, no person or...

The Practice of Guangzhou Port Planning Environmental Impact Assessment

NASA Astrophysics Data System (ADS)

Wang, Ning; Zhao, Junjie; Shou, Youping; Qiao, Jianzhe; Dong, Shipei; Zhang, Lu

2018-01-01

In this paper, the effects of the implementation of Guangzhou port plan were analyzed from hydrological condition, water environment and ecological environment. Regional water environmental carrying capacity was analyzed. Guangzhou port is a main port in the coast of China, it is an important port of foreign trade in south China, it is an important port for energy supplies and raw materials in Guangdong province [1]. With the shipping channel condition improvement and the construction of large specialized container port area, Guangzhou port will gradually become trunk line port of container transport in south China.

OMI air-quality monitoring over the Middle East

NASA Astrophysics Data System (ADS)

Barkley, Michael P.; González Abad, Gonzalo; Kurosu, Thomas P.; Spurr, Robert; Torbatian, Sara; Lerot, Christophe

2017-04-01

Using Ozone Monitoring Instrument (OMI) trace gas vertical column observations of nitrogen dioxide (NO2), formaldehyde (HCHO), sulfur dioxide (SO2), and glyoxal (CHOCHO), we have conducted a robust and detailed time series analysis to assess changes in local air quality for over 1000 locations (focussing on urban, oil refinery, oil port, and power plant targets) over the Middle East for 2005-2014. Apart from NO2, which is highest over urban locations, average tropospheric column levels of these trace gases are highest over oil ports and refineries. The highest average pollution levels over urban settlements are typically in Bahrain, Kuwait, Qatar, and the United Arab Emirates. We detect 278 statistically significant and real linear NO2 trends in total. Over urban areas NO2 increased by up to 12 % yr-1, with only two locations showing a decreasing trend. Over oil refineries, oil ports, and power plants, NO2 increased by about 2-9 % yr-1. For HCHO, 70 significant and real trends were detected, with HCHO increasing by 2-7 % yr-1 over urban settlements and power plants and by about 2-4 % yr-1 over refineries and oil ports. Very few SO2 trends were detected, which varied in direction and magnitude (23 increasing and 9 decreasing). Apart from two locations where CHOCHO is decreasing, we find that glyoxal tropospheric column levels are not changing over the Middle East. Hence, for many locations in the Middle East, OMI observes a degradation in air quality over 2005-2014. This study therefore demonstrates the capability of OMI to generate long-term air-quality monitoring at local scales over this region.

Testing and Analysis of Sensor Ports

NASA Technical Reports Server (NTRS)

Zhang, M.; Frendi, A.; Thompson, W.; Casiano, M. J.

2016-01-01

This Technical Publication summarizes the work focused on the testing and analysis of sensor ports. The tasks under this contract were divided into three areas: (1) Development of an Analytical Model, (2) Conducting a Set of Experiments, and (3) Obtaining Computational Solutions. Results from the experiment using both short and long sensor ports were obtained using harmonic, random, and frequency sweep plane acoustic waves. An amplification factor of the pressure signal between the port inlet and the back of the port is obtained and compared to models. Comparisons of model and experimental results showed very good agreement.

Electrification of the freight train network from the Ports of Los Angeles and Long Beach to the Inland Empire.

DOT National Transportation Integrated Search

2008-05-01

The goal of this project was to evaluate the benefits of electrifying the freight railroads connecting the Ports of Los Angeles and Long Beach with the Inland Empire. These benefits include significant reduction in air pollution, and improvements in ...

One, Two, or Three Ports in Laparoscopic Cholecystectomy?

PubMed Central

Justo-Janeiro, Jaime Manuel; Vincent, Gustavo Theurel; Vázquez de Lara, Fernando; de la Rosa Paredes, René; Orozco, Eduardo Prado; Vázquez de Lara, Luis G.

2014-01-01

Single-port laparoscopic cholecystectomy (LC) has been compared with 3- or 4-port LC. To our knowledge, there are no studies comparing the 3-, 2-, and 1-port techniques. Patients were randomized into 3 groups: LC 1-port using SILS, LC 2-port using a laparoscope with a working channel, and LC 3-port using the standard ports. Pain was evaluated at recovery, 4 hours, 24 hours, day 5, and day 8, using an analog visual scale. Homogenous groups in their demographic characteristics; all confirmed gallbladder lithiasis. At recovery, there was less pain in group 1 (P = 0.002); at 4 hours pain was similar in all groups (P = 0.899); at 24 hours there was less pain in groups 2 and 3 (P = 0.031); and at days 5 and 8 there was marginal (P = 0.053) and significant (P = 0.003) relevance. In terms of pain perception, LC performed through 1 port does not offer advantages when compared with 2 or 3 ports. More clinical trials are needed to confirm these data. PMID:25437581

Analysis of the intraocular jet flows and pressure gradients induced by air and fluid infusion: mechanism of focal chorioretinal damage.

PubMed

Kim, Yong Joon; Jo, Sungkil; Moon, Daruchi; Joo, Youngcheol; Choi, Kyung Seek

2014-05-01

To comprehend the mechanism of focal chorioretinal damage by analysis of the pressure distribution and dynamic pressure induced by infused air during fluid-air exchange. A precise simulation featuring a model eye and a fluid circuit was designed to analyze fluid-air exchange. The pressure distribution, flow velocity, and dynamic pressure induced by infusion of air into an air-filled eye were analyzed using an approach based on fluid dynamics. The size of the port and the infusion pressure were varied during simulated iterations. We simulated infusion of an air-filled eye with balanced salt solution (BSS) to better understand the mechanism of chorioretinal damage induced by infused air. Infused air was projected straight toward a point on the retina contralateral to the infusion port (the "vulnerable point"). The highest pressure was evident at the vulnerable point, and the lowest pressure was recorded on most retinal areas. Simulations using greater infusion pressure and a port of larger size were associated with elevations in dynamic pressure and the pressure gradient. The pressure gradients were 2.8 and 5.1 mm Hg, respectively, when infusion pressures of 30 and 50 mm Hg were delivered through a 20-gauge port. The pressure gradient associated with BSS infusion was greater than that created by air, but lasted for only a moment. Our simulation explains the mechanism of focal chorioretinal damage in numerical terms. Infused air induces a prolonged increase in focal pressure on the vulnerable point, and this may be responsible for visual field defects arising after fluid-air exchange. Copyright 2014 The Association for Research in Vision and Ophthalmology, Inc.

Evaluation of a polymer implanted port access device.

PubMed

Brown, J M

1996-01-01

The implanted port vascular access system has provided many patients with safe and reliable vascular access. Its implanted design provides improved body image, reduced maintenance and a better quality of life. The Huber needle has been the standard means of accessing the implanted port system. Because of the problems associated with the Huber needle system, current standards recommend that the Huber needle be changed every 7 days. This evaluation examines the use of a polymer cannula to access the implanted port system. This polymer cannula eliminates many of the problems associated with the Huber needle and provides longer dwell times without increased complications. Seventy nine patients were accessed for a total of 1533 days with the mean dwell time being 19.4 days with no increase in complications associated with port access. To establish implanted port access times of greater than 7 days without increased complications. A multicenter voluntary enrollment evaluation of a medical device. Patients were offered the opportunity to participate in the evaluation if they had an implanted port and were going to be accessed for therapy for periods of 7 days or more. Patients were observed for adverse cutaneous reactions at the insertion site and any port access complications such as sepsis, leakage, changes in portal chamber integrity, and implant pocket integrity. From October 1994 through November 1995, 79 L-Cath for Ports (Luther Medical Products) polymer catheter port access devices (Illustration 1) were inserted in 54 patients. This polymer port access device was used instead of a rigid metal Huber needle for port access. The total number of access days was 1533 days with the mean duration of access being 19.4 days. Two patients experienced blood stream infections while they were accessed with the polymer port access device. These infections ensued with fever of unknown origin as the presenting symptom during neutropenic episodes after chemotherapy treatment. The

Staged fuel and air injection in combustion systems of gas turbines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hughes, Michael John; Berry, Jonathan Dwight

A gas turbine that includes a working fluid flowpath extending aftward from a forward injector in a combustor. The combustor may include an inner radial wall, an outer radial wall, and, therebetween, a flow annulus. A staged injector may intersect the flow annulus so to attain an injection point within the working fluid flowpath by which aftward and forward annulus sections are defined. Air directing structure may include an aftward intake section that corresponds to the aftward annulus section and a forward intake section that corresponds to the forward annulus section. The air directing structure may be configured to: directmore » air entering through the aftward intake section through the aftward annulus section in a forward direction to the staged injector; and direct air entering through the forward intake section through the forward annulus section in a forward direction to the forward injector.« less

Staged fuel and air injection in combustion systems of gas turbines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hughes, Michael John; Berry, Jonathan Dwight

A gas turbine that includes a working fluid flowpath extending aftward from a forward injector in a combustor. The combustor may include an inner radial wall, an outer radial wall, and, therebetween, a flow annulus. A staged injector may intersect the flow annulus so to attain an injection point within the working fluid flowpath by which aftward and forward annulus sections are defined. Air directing structure may include an aftward intake section that corresponds to the aftward annulus section and a forward intake section that corresponds to the forward annulus section. The air directing structure may be configured to: directmore » air entering through the aftward intake section through the aftward annulus section in a forward direction to the staged injector; and direct air entering through the forward intake section through the forward annulus section in an aftward direction to the staged injector.« less

Two-port robotic hysterectomy: a novel approach.

PubMed

Moawad, Gaby N; Tyan, Paul; Khalil, Elias D Abi

2018-03-24

The objective of the study was to demonstrate a novel technique for two-port robotic hysterectomy with a particular focus on the challenging portions of the procedure. The study is designed as a technical video, showing step-by-step a two-port robotic hysterectomy approach (Canadian Task Force classification level III). IRB approval was not required for this study. The benefits of minimally invasive surgery for gynecological pathology have been clearly documented in multiple studies. Patients had fewer medical and surgical complications postoperatively, better cosmesis and quality of life. Most gynecological surgeons require 3-5 ports for the standard gynecological procedure. Even though the minimally invasive multiport system provides an excellent safety profile, multiple incisions are associated with a greater risk for morbidity including infection, pain, and hernia. In the past decade, various new methods have emerged to minimize the number of ports used in gynecological surgery. The interventions employed were a two-port robotic hysterectomy, using a camera port plus one robotic arm, with a focus on salpingectomy and cuff closure. We describe a transvaginal and a transabdominal approach for salpingectomy and a novel method for cuff closure. The transvaginal and transabdominal techniques for salpingectomy for two-port robotic-assisted hysterectomy provide excellent tension and exposure for a safe procedure without the need for an extra port. We also describe a transvaginal technique to place the vaginal cuff on tension during closure. With the necessary set of skills on a carefully chosen patient, two-port robotic-assisted total laparoscopic hysterectomy is a feasible procedure.

[Subcutaneous implantation type central venous port management in patients with malignant tumors effect of different antiseptic agents on central venous port-related infection].

PubMed

Sato, Junya; Kumagai, Masumi; Kato, Kenichi; Akahane, Akio; Suzuki, Michiko; Kashiwaba, Masahiro; Sone, Miyuki; Kudo, Kenzo

2014-08-01

Subcutaneous implantation type central venous ports(CV ports)are used in chemotherapy. Here, we prospectively examined the frequency of CV port-related infections when the disinfectant was changed from 10% povidone iodine to 1% chlorhexidine ethanol or 70% ethanol. The subjects were patients with malignant tumors, who had newly been implanted with CV ports. We examined CV port-related infections at 1 week after CV port implantation and every 2 weeks thereafter, following sterilization upon insertion of a Huber needle to the CV port. CV port evulsion due to CV port-related infection was noted in 3 patients(4.8%)in whom 15%chlorhexidine ethanol was used(n=62)and in 2 patients(3.3%)in whom 70% ethanol was used(n=60). Infection rates per 1,000 days of CV port use were 1.48% and 1.01%, respectively. Thus, the outcomes of sterilization using 1% chlorhexidine ethanol and 70% ethanol did not differ significantly from those on using 10% povidone iodine for sterilization, based on preliminary results at our institution(3 of 59 patients[5.1%]had port evulsion due to CV port-related infection and the infection rate per 1,000 days of CV port use was 1.47%, Akahane et al, 2012). Chlorhexidine ethanol and ethanol are very convenient to use because they dry quickly and do not need discoloration. Accordingly, chlorhexidine ethanol and ethanol might be useful in CV port management.

Single port VATS: recent developments in Asia.

PubMed

Yu, Peter S Y; Capili, Freddie; Ng, Calvin S H

2016-03-01

Single port video-assisted thoracic surgery (VATS) is the most recent evolution in minimally invasive thoracic surgery. With increasing global popularity, the single port VATS approach has been adopted by experienced thoracic surgeons in many Asian countries. From initial experience of single port VATS lobectomy to the more complex sleeve resection procedures now forming part of daily practice in some Asia institutes, the region has been the proving ground for single port VATS approaches' feasibility and safety. In addition, certain technical refinements in single port VATS lung resection and lymph node dissection have also sprung from Asia. Novel equipment designed to facilitate single port VATS allowing further reduce access trauma are being realized by the partnership between surgeons and the industries. Advanced thoracoscopes and staplers that are narrower and more maneuverable are particularly important in the smaller habitus of patients from Asia. These and similar new generation equipment are being applied to single port VATS in novel ways. As dedicated thoracic surgeons in the region continue to striving for excellence, innovative ideas in single incision access including subxiphoid and embryonic natural-orifice transluminal endoscopic surgery (e-NOTES) have been explored. Adjunct techniques and technology used in association with single port VATS such as non-intubated surgery, hybrid operating room image guidance and electromagnetic navigational bronchoscopy are all in rapid development in Asia.

Retrospective Comparison of Single-Port Sleeve Gastrectomy Versus Three-Port Laparoscopic Sleeve Gastrectomy: a Propensity Score Adjustment Analysis.

PubMed

Mauriello, Claudio; Chouillard, Elie; d'alessandro, Antonio; Marte, Gianpaolo; Papadimitriou, Argyri; Chahine, Elias; Kassir, Radwan

2018-04-16

Evaluate the efficacy of single-port sleeve gastrectomy (SPSG) and then compare it to a less-invasive sleeve approach (three-port) (3PSG) according to a propensity score (PS) matching analysis. We analyzed all patients who underwent SG through a three-port or a single-port laparoscopic approach. After 2 years, the follow-up was completed in 84% patients treated with 3PSG and 95% patients of the SPSG group. Excess weight loss (EWL) was comparable for the first year of follow-up within the two groups except for the controls at 3 months in which the SPSG group showed a higher EWL (p = 0.0243). We demonstrated the efficacy of SPSG in bariatric surgery even compared to another, less invasive, laparoscopic SG approach (three-port).

Ship emission inventory and its impact on the PM2.5 air pollution in Qingdao Port, North China

NASA Astrophysics Data System (ADS)

Chen, Dongsheng; Wang, Xiaotong; Nelson, Peter; Li, Yue; Zhao, Na; Zhao, Yuehua; Lang, Jianlei; Zhou, Ying; Guo, Xiurui

2017-10-01

In this study, a first high temporal-spatial ship emission inventory in Qingdao Port and its adjacent waters has been developed using a ;bottom-up; method based on Automatic Identification System (AIS) data. The total estimated ship emissions for SO2, NOX, PM10, PM2.5, HC and CO in 2014 are 3.32 × 104, 4.29 × 104, 4.54 × 103, 4.18 × 103, 1.85 × 103 and 3.66 × 103 tonnes, respectively. Emissions of SO2 and NOX from ships account for 9% and 13% of the anthropogenic totals in Qingdao, respectively. The main contributors to the ship emissions are containers, followed by fishing ships, oil tankers and bulk carriers. The inter-monthly ship emissions varied significantly due to two reasons: stopping of the fishing ship activities during the fishing moratorium and the reduction of freight volume around the Chinese New Year Festival. Emissions from transport vessels concentrated basically along the shipping routes, while fishing ships contributed to massive irregular spatial emissions in the sea. The impact of ship emissions on the ambient air quality was further investigated using the Weather Research and Forecasting with Chemistry (WRF/Chem) model. The results reveal that the contribution of ship emissions to the PM2.5 concentrations in Qingdao is the highest in summer (13.1%) and the lowest in winter (1.5%). The impact was more evident over densely populated urban areas, where the contributions from ship emissions could be over 20% in July due to their close range to the docks. These results indicated that the management and control of the ship emissions are highly demanded considering their remarkable influence on the air quality and potential negative effects on human health.

5-fluorouracil extravasation following port failure.

PubMed

Nesti, S P; Kovac, R

2000-01-01

A case is presented of cytotoxic extravasation as a result of an implantable venous port being perforated by a standard Huber needle. A patient receiving 5-fluorouracil via a dual reservoir port, implanted within the left chest wall, presented with hemoserous discharge from the right needle entry site. The left chest wall was warm to touch, erythematous, and swollen. Subcutaneous infiltration was suspected, and the infusion was ceased. A venogram was performed demonstrating significant extravasation around the left reservoir only. On port removal, inspection showed the Huber needle had penetrated the base plate on the left side. It is recommended that this complication be added as a possible sequelae of central venous port use.

Public Port Finance Survey for FY 1999

DOT National Transportation Integrated Search

2001-01-01

The Public Port Finance Survey has been compiled for over 20 years, first by the AAPA or a member port, now by the Maritime Administration (MARAD).It is the only report of its kind in the port industry covering U.S. (including U.S. territories) and C...

Cold flow simulation of an internal combustion engine with vertical valves using layering approach

NASA Astrophysics Data System (ADS)

Martinas, G.; Cupsa, O. S.; Stan, L. C.; Arsenie, A.

2015-11-01

Complying with emission requirements and fuel consumption efficiency are the points which drive any development of internal combustion engine. Refinement of the process of combustion and mixture formation, together with in-cylinder flow refinement, is a requirement, valves and piston bowl and intake exhaust port design optimization is essential. In order to reduce the time for design optimization cycle it is used Computational Fluid Dynamics (CFD). Being time consuming and highly costly caring out of experiment using flow bench testing this methods start to become less utilized. Air motion inside the intake manifold is one of the important factors, which govern the engine performance and emission of multi-cylinder diesel engines. Any cold flow study on IC is targeting the process of identifying and improving the fluid flow inside the ports and the combustion chamber. This is only the base for an optimization process targeting to increase the volume of air accessing the combustion space and to increase the turbulence of the air at the end of the compression stage. One of the first conclusions will be that the valve diameter is a fine tradeoff between the need for a bigger diameter involving a greater mass of air filling the cylinder, and the need of a smaller diameter in order to reduce the blind zone. Here there is room for optimization studies. The relative pressure indicates a suction effect coming from the moving piston. The more the shape of the inlet port is smoother and the diameter of the piston is bigger, the aerodynamic resistance of the geometry will be smaller so that the difference of inlet port pressure and the pressure near to piston face will be smaller. Here again there is enough room for more optimization studies.

Rorschach inkblot port-wine stain.

PubMed

Coots, N V; Elston, D M

1997-01-01

We present an infant born with bilaterally symmetric, anterior and posterior port-wine stains. These lesions presented a striking resemblance to Rorschach inkblots, a phenomenon not previously reported. A discussion of the case as well as a discussion of syndromes associated with port-wine stains is provided.

Wounds caused by contact with muzzle-lift relief ports (Mag-Na-Port).

PubMed

Rogers, D R; Shem, R J

1992-12-01

Fan-shaped stippled burns were produced on the skin when a revolver whose barrel had been modified by the Mag-Na-Port process was fired twice with the side of the muzzle in contact. A grazing wound was produced by one bullet, and an oblique entry was produced by the other. The characteristics of Mag-Na-Port wounds and test shots are described, and these are compared with test shots from two other higher power revolvers.

Detecting and Characterizing Semantic Inconsistencies in Ported Code

NASA Technical Reports Server (NTRS)

Ray, Baishakhi; Kim, Miryung; Person, Suzette J.; Rungta, Neha

2013-01-01

Adding similar features and bug fixes often requires porting program patches from reference implementations and adapting them to target implementations. Porting errors may result from faulty adaptations or inconsistent updates. This paper investigates (I) the types of porting errors found in practice, and (2) how to detect and characterize potential porting errors. Analyzing version histories, we define five categories of porting errors, including incorrect control- and data-flow, code redundancy, inconsistent identifier renamings, etc. Leveraging this categorization, we design a static control- and data-dependence analysis technique, SPA, to detect and characterize porting inconsistencies. Our evaluation on code from four open-source projects shows thai SPA can dell-oct porting inconsistencies with 65% to 73% precision and 90% recall, and identify inconsistency types with 58% to 63% precision and 92% to 100% recall. In a comparison with two existing error detection tools, SPA improves precision by 14 to 17 percentage points

Detecting and Characterizing Semantic Inconsistencies in Ported Code

NASA Technical Reports Server (NTRS)

Ray, Baishakhi; Kim, Miryung; Person,Suzette; Rungta, Neha

2013-01-01

Adding similar features and bug fixes often requires porting program patches from reference implementations and adapting them to target implementations. Porting errors may result from faulty adaptations or inconsistent updates. This paper investigates (1) the types of porting errors found in practice, and (2) how to detect and characterize potential porting errors. Analyzing version histories, we define five categories of porting errors, including incorrect control- and data-flow, code redundancy, inconsistent identifier renamings, etc. Leveraging this categorization, we design a static control- and data-dependence analysis technique, SPA, to detect and characterize porting inconsistencies. Our evaluation on code from four open-source projects shows that SPA can detect porting inconsistencies with 65% to 73% precision and 90% recall, and identify inconsistency types with 58% to 63% precision and 92% to 100% recall. In a comparison with two existing error detection tools, SPA improves precision by 14 to 17 percentage points.

Trocar Port Hernias After Bariatric Surgery.

PubMed

Coblijn, Usha K; de Raaff, Christel A L; van Wagensveld, Bart A; van Tets, Willem F; de Castro, Steve M M

2016-03-01

Laparoscopic bariatric surgery is increasingly being performed worldwide. It is estimated that trocar port hernias occur more often in obese patients due to their obesity and because the ports are not closed routinely. The aim of the present study was to analyze the incidence, risk factors, and management of patients with trocar port hernias after laparoscopic bariatric surgery. All patients who were operated between 2006 and 2013 were included. During the study period, the trocar ports were not closed routinely. All patients who had any symptomatic abdominal wall hernia during follow-up were included. Overall, 1524 laparoscopic bariatric procedures were performed. There were 1249 female (82 %) and 275 male (18 %) patients. The mean age was 44 years, and median body mass index was 43 kg/m(2). Patients underwent laparoscopic Roux-en-Y gastric bypass (LRYGB) (n = 859), laparoscopic adjustable gastric banding (LAGB) (n = 364), laparoscopic sleeve gastrectomy (LSG) (n = 68), revisional surgery (n = 226), and other procedures (n = 7). Three hundred and one patients (20 %) had one or more postoperative complications and the overall mortality was 0.3 % (four patients). There were 14 patients (0.9 %) with an abdominal wall hernia, of which eight (0.5 %) had a trocar port hernia, three (0.2 %) an incisional hernia from other previous surgery, and three (0.2 %) an umbilical hernia. Gender, age, BMI, smoking, type II diabetes, procedure type, complications, and weight loss were not associated with the occurrence of abdominal wall hernias. Trocar port hernias after bariatric surgery occur seldom if the trocar port is not routinely closed.

The Market Demand for Air Transportation

NASA Technical Reports Server (NTRS)

Taneja, N.

1972-01-01

Although the presentation will touch upon the areas of market for air transportation, the theoretical foundations of the demand function, the demand models, and model selection and evaluation, the emphasis of the presentation will be on a qualitative description of the factors affecting the demand for air transportation. The presentation will rely heavily on the results of market surveys carried out by the Port of New York Authority, the University of Michigan, and Census of Transportation.

Analysis of laparoscopic port site complications: A descriptive study

PubMed Central

Karthik, Somu; Augustine, Alfred Joseph; Shibumon, Mundunadackal Madhavan; Pai, Manohar Varadaraya

2013-01-01

CONTEXT: The rate of port site complications following conventional laparoscopic surgery is about 21 per 100,000 cases. It has shown a proportional rise with increase in the size of the port site incision and trocar. Although rare, complications that occur at the port site include infection, bleeding, and port site hernia. AIMS: To determine the morbidity associated with ports at the site of their insertion in laparoscopic surgery and to identify risk factors for complications. SETTINGS AND DESIGN: Prospective descriptive study. MATERIALS AND METHODS: In the present descriptive study, a total of 570 patients who underwent laparoscopic surgeries for various ailments between August 2009 and July 2011 at our institute were observed for port site complications prospectively and the complications were reviewed. STATISTICAL ANALYSIS USED: Descriptive statistical analysis was carried out in the present study. The statistical software, namely, SPSS 15.0 was used for the analysis of the data. RESULTS: Of the 570 patients undergoing laparoscopic surgery, 17 (3%) had developed complications specifically related to the port site during a minimum follow-up of three months; port site infection (PSI) was the most frequent (n = 10, 1.8%), followed by port site bleeding (n = 4, 0.7%), omentum-related complications (n = 2; 0.35%), and port site metastasis (n = 1, 0.175%). CONCLUSIONS: Laparoscopic surgeries are associated with minimal port site complications. Complications are related to the increased number of ports. Umbilical port involvement is the commonest. Most complications are manageable with minimal morbidity, and can be further minimized with meticulous surgical technique during entry and exit. PMID:23741110

A study of optimum cowl shapes and flow port locations for minimum drag with effective engine cooling, volume 1

NASA Technical Reports Server (NTRS)

Fox, S. R.; Smetana, F. O.

1980-01-01

The contributions to the cruise drag of light aircraft arising from the shape of the engine cowl and the forward fuselage area and also that resulting from the cooling air mass flow through intake and exhaust sites on the nacelle were analyzed. The methods employed for the calculation of the potential flow about an arbitrary three dimensional body are described with modifications to include the effects of boundary layer displacement thickness, a nonuniform onset flow field (such as that due to a rotating propeller), and the presence of air intakes and exhausts. A simple, reliable, largely automated scheme to better define or change the shape of a body is also presented. A technique was developed which can yield physically acceptable skin friction and pressure drag coefficients for isolated light aircraft bodies. For test cases on a blunt nose Cessna 182 fuselage, the technique predicted drag reductions as much as 28.5% by body recontouring and proper placements and sizing of the cooling air intakes and exhausts.

Panama Canal Expansion Illustrates Need for Multimodal Near-Source Air Quality Assessment

EPA Science Inventory

The compelling issue raised is potential major changes in goods movement due to the Panama Canal expansion and considerations for near-source air quality. Near-source air quality may be affected both at near-port areas as well as along the freight transportation corridor.

Single-port plus an additional port robotic complete mesocolic excision and intracorporeal anastomosis using a robotic stapler for right-sided colon cancer

PubMed Central

Bae, Sung Uk; Jeong, Woon Kyung

2016-01-01

The concept of complete mesocolic excision and central vascular ligation for colonic cancer has been recently introduced. The paper describes a technique of right-sided complete mesocolic excision and intracorporeal anastomosis by using a single-port robotic approach with an additional conventional robotic port. We performed a single-port plus an additional port robotic surgery using the Da Vinci Single-Site platform via the Pfannenstiel incision and the wristed robotic instruments via an additional robotic port in the left lower quadrant. The total operative and docking times were 280 and 25 minutes, respectively. The total number of lymph nodes harvested was 36 and the proximal and distal resection margins were 31 and 50 cm, respectively. Single-port plus an additional port robotic surgery for right-sided complete mesocolic excision and intracorporeal anastomosis appears to be feasible and safe. This system can overcome certain limitations of the previous robotic systems and conventional single-port laparoscopic surgery. PMID:27757400

Single-port plus an additional port robotic complete mesocolic excision and intracorporeal anastomosis using a robotic stapler for right-sided colon cancer.

PubMed

Bae, Sung Uk; Jeong, Woon Kyung; Baek, Seong Kyu

2016-10-01

The concept of complete mesocolic excision and central vascular ligation for colonic cancer has been recently introduced. The paper describes a technique of right-sided complete mesocolic excision and intracorporeal anastomosis by using a single-port robotic approach with an additional conventional robotic port. We performed a single-port plus an additional port robotic surgery using the Da Vinci Single-Site platform via the Pfannenstiel incision and the wristed robotic instruments via an additional robotic port in the left lower quadrant. The total operative and docking times were 280 and 25 minutes, respectively. The total number of lymph nodes harvested was 36 and the proximal and distal resection margins were 31 and 50 cm, respectively. Single-port plus an additional port robotic surgery for right-sided complete mesocolic excision and intracorporeal anastomosis appears to be feasible and safe. This system can overcome certain limitations of the previous robotic systems and conventional single-port laparoscopic surgery.

Near-source air quality assessment: challenges and collaboration

EPA Science Inventory

This presentation is to give a general overview of near-source air pollution concerns and recent EPA projects (near-road, near-rail, near-port), as well as explaining how these projects were implemented through collaboration internally and externally.

75 FR 35296 - Safety Zones; 2010 Muskegon Summer Celebration Air Show, Muskegon Lake, Muskegon, MI

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-22

...-AA00 Safety Zones; 2010 Muskegon Summer Celebration Air Show, Muskegon Lake, Muskegon, MI AGENCY: Coast... portions of Muskegon Lake due to the 2010 Muskegon Summer Celebration Air Show. These temporary safety... 2010 Muskegon Summer Celebration Air Show. The Captain of the Port, Sector Lake Michigan, has...

Port-Orford-Cedar Root Disease

Treesearch

Lewis F. Roth; Robert D. Jr. Harvey; John T. Kliejunas

1987-01-01

The most serious disease of Port-Orford-cedar (Chamaecyparis lawsoniana (A. Murr.) Parl.) is a root disease caused by the fungus Phytophthora lateralis. Nursery stock, ornamentals, and timber trees are subject to attack. Other species of Chamaecyparis are less susceptible than Port-Orford-cedar, and trees of other genera are not affected.

Transport and Environment Database System (TRENDS): Maritime air pollutant emission modelling

NASA Astrophysics Data System (ADS)

Georgakaki, Aliki; Coffey, Robert A.; Lock, Graham; Sorenson, Spencer C.

This paper reports the development of the maritime module within the framework of the Transport and Environment Database System (TRENDS) project. A detailed database has been constructed for the calculation of energy consumption and air pollutant emissions. Based on an in-house database of commercial vessels kept at the Technical University of Denmark, relationships between the fuel consumption and size of different vessels have been developed, taking into account the fleet's age and service speed. The technical assumptions and factors incorporated in the database are presented, including changes from findings reported in Methodologies for Estimating air pollutant Emissions from Transport (MEET). The database operates on statistical data provided by Eurostat, which describe vessel and freight movements from and towards EU 15 major ports. Data are at port to Maritime Coastal Area (MCA) level, so a bottom-up approach is used. A port to MCA distance database has also been constructed for the purpose of the study. This was the first attempt to use Eurostat maritime statistics for emission modelling; and the problems encountered, since the statistical data collection was not undertaken with a view to this purpose, are mentioned. Examples of the results obtained by the database are presented. These include detailed air pollutant emission calculations for bulk carriers entering the port of Helsinki, as an example of the database operation, and aggregate results for different types of movements for France. Overall estimates of SO x and NO x emission caused by shipping traffic between the EU 15 countries are in the area of 1 and 1.5 million tonnes, respectively.

Draft Environmental Justice Primer for Ports

EPA Pesticide Factsheets

This document is intended to help port decision-makers better understand the needs of near-port communities and how they can help address these needs and build productive community relationships during planning activities and operations.

Ports Primer: 3.3 Federal and International Governance

EPA Pesticide Factsheets

State and local governments are important players in port governance and in oversight of transportation projects that may affect ports. Private corporations may also play a role if they lease or own a terminal at a port.

An integrated port camera and display system for laparoscopy.

PubMed

Terry, Benjamin S; Ruppert, Austin D; Steinhaus, Kristen R; Schoen, Jonathan A; Rentschler, Mark E

2010-05-01

In this paper, we built and tested the port camera, a novel, inexpensive, portable, and battery-powered laparoscopic tool that integrates the components of a vision system with a cannula port. This new device 1) minimizes the invasiveness of laparoscopic surgery by combining a camera port and tool port; 2) reduces the cost of laparoscopic vision systems by integrating an inexpensive CMOS sensor and LED light source; and 3) enhances laparoscopic surgical procedures by mechanically coupling the camera, tool port, and liquid crystal display (LCD) screen to provide an on-patient visual display. The port camera video system was compared to two laparoscopic video systems: a standard resolution unit from Karl Storz (model 22220130) and a high definition unit from Stryker (model 1188HD). Brightness, contrast, hue, colorfulness, and sharpness were compared. The port camera video is superior to the Storz scope and approximately equivalent to the Stryker scope. An ex vivo study was conducted to measure the operative performance of the port camera. The results suggest that simulated tissue identification and biopsy acquisition with the port camera is as efficient as with a traditional laparoscopic system. The port camera was successfully used by a laparoscopic surgeon for exploratory surgery and liver biopsy during a porcine surgery, demonstrating initial surgical feasibility.

Rotary sequencing valve with flexible port plate

DOEpatents

Wagner, Glenn Paul

2005-05-10

Rotary sequencing valve comprising a rotor having a rotor face rotatable about an axis perpendicular to the rotor face, wherein the rotor face has a plurality of openings, one or more of which are disposed at a selected radial distance from the axis, and wherein the rotor includes at least one passage connecting at least one pair of the plurality of openings. The valve includes a flexible port plate having a first side and a second side, wherein the first side faces the rotor and engages the rotor such that the flexible port plate can be rotated coaxially by the rotor and can move axially with respect to the rotor, wherein the flexible port plate has a plurality of ports between the first and second sides, which ports are aligned with the openings in the rotor face. The valve also includes a stator having a stator face disposed coaxially with the rotor and the flexible port plate, wherein the second side of the flexible port plate is in sealable, slidable rotary contact with the stator face, wherein the stator face has a plurality of openings, some of which are disposed at the selected radial distance from the axis, and wherein the plurality of openings extend as passages through the stator. The valve may be used in pressure or temperature swing adsorption systems.

Securing a port's future through Circular Economy: Experiences from the Port of Gävle in contributing to sustainability.

PubMed

Carpenter, Angela; Lozano, Rodrigo; Sammalisto, Kaisu; Astner, Linda

2018-03-01

Ports are an important player in the world, due to their role in global production and distributions systems. They are major intermodal transport hubs, linking the sea to the land. For all ports, a key requirement for commercial and economic viability is to retain ships using them and to remain accessible to those ships. Ports need to find approaches to help them remain open. They must ensure their continued economic viability. At the same time, they face increasing pressure to become more environmentally and socially conscious. This paper examines the approach taken by the Port of Gävle, Sweden, which used contaminated dredged materials to create new land using principles of Circular Economy. The paper demonstrates that using Circular Economy principles can be a viable way of securing a port's future and contributing to its sustainability, and that of the city/region where it operates. Copyright © 2018 Elsevier Ltd. All rights reserved.

Queuing theory models used for port equipment sizing

NASA Astrophysics Data System (ADS)

Dragu, V.; Dinu, O.; Ruscă, A.; Burciu, Ş.; Roman, E. A.

2017-08-01

The significant growth of volumes and distances on road transportation led to the necessity of finding solutions to increase water transportation market share together with the handling and transfer technologies within its terminals. It is widely known that the biggest times are consumed within the transport terminals (loading/unloading/transfer) and so the necessity of constantly developing handling techniques and technologies in concordance with the goods flows size so that the total waiting time of ships within ports is reduced. Port development should be achieved by harmonizing the contradictory interests of port administration and users. Port administrators aim profit increase opposite to users that want savings by increasing consumers’ surplus. The difficulty consists in the fact that the transport demand - supply equilibrium must be realised at costs and goods quantities transiting the port in order to satisfy the interests of both parties involved. This paper presents a port equipment sizing model by using queueing theory so that the sum of costs for ships waiting operations and equipment usage would be minimum. Ship operation within the port is assimilated to a mass service waiting system in which parameters are later used to determine the main costs for ships and port equipment.

Log exports by port, 1987.

Treesearch

Debra D. Warren

1989-01-01

Volumes and average values of log exports by port have been compiled by quarter for 1987. The tables show the four Northwest customs districts by ports, species, and destinations. These data were received from the U.S. Department of Commerce too late to be published in the 1987 quarterly reports, "Production, Prices, Employment, and Trade in Northwest Forest...

Port Security: A National Planning Guide

DOT National Transportation Integrated Search

1997-01-01

Port Security: A National Planning Guide has been produced for the purpose of conveying the United States Department of Transportations policy perspective on port security to the maritime community. This guide provides an overview of the essential as...

Investigation of the Behavior of Fuel in the Intake Manifold and its Relation to S. I. Engines, 1980-1983

NASA Astrophysics Data System (ADS)

Servati, Hamid Beyragh

A liquid fuel film formation on the walls of an intake manifold adversely affects the engine performance and alters the overall air/fuel ratio from that scheduled by a fuel injector or carburetor and leads to adverse effects in vehicle driveability, exhaust emissions, and fuel economy. In this dissertation, the intake manifold is simulated by a horizontal circular duct. A model is provided to predict the rate of deposition and evaporation of the droplets in the intake manifold. The liquid fuel flow rate into the cylinders, mean film velocity and film thickness are determined as functions of engine parameters for both steady and transient operating conditions of the engine. A mathematical engine model is presented to simulate the dynamic interactions of the various engine components such as the air/fuel inlet element, intake manifold, combustion, dynamics and exhaust emissions. Inputs of the engine model are the intake manifold pressure and temperature, throttle angle, and air/fuel ratio. The observed parameters are the histories of fuel film thickness and velocity, fuel consumption, engine speed, engine speed hesitation time, and histories of CO, CO(,2), NO(,x), CH(,n), and O(,2). The effects of different air/fuel ratio control strategies on engine performance and observed parameters are also shown.

Occupational hazards to health of port workers.

PubMed

Wang, Yukun; Zhan, Shuifen; Liu, Yan; Li, Yan

2017-12-01

The aim of this article is to reduce the risk of occupational hazards and improve safety conditions by enhancing hazard knowledge and identification as well as improving safety behavior for freight port enterprises. In the article, occupational hazards to health and their prevention measures of freight port enterprises have been summarized through a lot of occupational health evaluation work, experience and understanding. Workers of freight port enterprises confront an equally wide variety of chemical, physical and psychological hazards in production technology, production environment and the course of labor. Such health hazards have been identified, the risks evaluated, the dangers to health notified and effective prevention measures which should be put in place to ensure the health of the port workers summarized. There is still a long way to go for the freight port enterprises to prevent and control the occupational hazards. Except for occupational hazards and their prevention measures, other factors that influence the health of port workers should also be paid attention to, such as age, work history, gender, contraindication and even the occurrence and development rules of occupational hazards in current production conditions.

Peripheral Venous Access Ports: Outcomes Analysis in 109 Patients

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bodner, Leonard J.; Nosher, John L.; Patel, Kaushik M.

Purpose: To perform a retrospective outcomes analysis of central venous catheters with peripheral venous access ports, with comparison to published data.Methods: One hundred and twelve central venous catheters with peripherally placed access ports were placed under sonographic guidance in 109 patients over a 4-year period. Ports were placed for the administration of chemotherapy, hyperalimentation, long-term antibiotic therapy, gamma-globulin therapy, and frequent blood sampling. A vein in the upper arm was accessed in each case and the catheter was passed to the superior vena cava or right atrium. Povidone iodine skin preparation was used in the first 65 port insertions. Amore » combination of Iodophor solution and povidone iodine solution was used in the last 47 port insertions. Forty patients received low-dose (1 mg) warfarin sodium beginning the day after port insertion. Three patients received higher doses of warfarin sodium for preexistent venous thrombosis. Catheter performance and complications were assessed and compared with published data.Results: Access into the basilic or brachial veins was obtained in all cases. Ports remained functional for a total of 28,936 patient days. The port functioned in 50% of patients until completion of therapy, or the patient's expiration. Ports were removed prior to completion of therapy in 18% of patients. Eleven patients (9.9% of ports placed) suffered an infectious complication (0.38 per thousand catheter-days)-in nine, at the port implantation site, in two along the catheter. In all 11 instances the port was removed. Port pocket infection in the early postoperative period occurred in three patients (4.7%) receiving a Betadine prep vs two patients (4.2%) receiving a standard O.R. prep. This difference was not statistically significant (p = 0.9). Venous thrombosis occurred in three patients (6.8%) receiving warfarin sodium and in two patients (3%) not receiving warfarin sodium. This difference was not statistically

Development of size-selective sampling of Bacillus anthracis surrogate spores from simulated building air intake mixtures for analysis via laser-induced breakdown spectroscopy.

PubMed

Gibb-Snyder, Emily; Gullett, Brian; Ryan, Shawn; Oudejans, Lukas; Touati, Abderrahmane

2006-08-01

Size-selective sampling of Bacillus anthracis surrogate spores from realistic, common aerosol mixtures was developed for analysis by laser-induced breakdown spectroscopy (LIBS). A two-stage impactor was found to be the preferential sampling technique for LIBS analysis because it was able to concentrate the spores in the mixtures while decreasing the collection of potentially interfering aerosols. Three common spore/aerosol scenarios were evaluated, diesel truck exhaust (to simulate a truck running outside of a building air intake), urban outdoor aerosol (to simulate common building air), and finally a protein aerosol (to simulate either an agent mixture (ricin/anthrax) or a contaminated anthrax sample). Two statistical methods, linear correlation and principal component analysis, were assessed for differentiation of surrogate spore spectra from other common aerosols. Criteria for determining percentages of false positives and false negatives via correlation analysis were evaluated. A single laser shot analysis of approximately 4 percent of the spores in a mixture of 0.75 m(3) urban outdoor air doped with approximately 1.1 x 10(5) spores resulted in a 0.04 proportion of false negatives. For that same sample volume of urban air without spores, the proportion of false positives was 0.08.

High speed variable delivery helical screw compressor/expander automotive air conditioning and waste heat energy recovery system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gagnon, J.A.; Schaefer, D.D.; Shaw, D.N.

1980-09-02

A compact, helical screw compressor/expander unit is described that is mounted in a vehicle and connected to the vehicle engine driven drive shaft has inlet and outlet ports and a capacity control slide valve and a pressure matching or volume ratio slide valve, respectively, for said ports. A refrigerant loop includes the compressor, a condenser mounted in the path of air flow over the engine and an evaporator mounted in a fresh air/cab return air flow duct for the occupant. Heat pipes thermally connect the cab air flow duct to the engine exhaust system which also bears the vapor boiler.more » Selectively operated damper valves control the fresh air/cab return air for passage selectively over the evaporator coil and the heat pipes as well as the exhaust gas flow over opposite ends of the heat pipes and the vapor boiler.« less

Fresh air indoors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kull, K.

1988-09-01

This article describes and compares ventilation systems for the control of indoor air pollution in residential housing. These include: local exhaust fans, whole-house fans, central exhaust with wall ports, and heat-recovery central ventilation (HRV). HRV's have a higher initial cost than the other systems but they are the only ones that save energy. Homeowners are given guidelines for choosing the system best suited for their homes in terms of efficiency and payback period.

Research for Foreign Advanced Ports for Protection and Development Experience

NASA Astrophysics Data System (ADS)

Zhang, Lu; Tian, Mingjing; Zhao, Junjie; Shou, Youping; Wang, Ning; Qiao, Jianzhe; Li, Guanglou

2018-04-01

Into the twenty-first century, the process globalization of economic and trade is getting faster and faster, As of 2014, China's annual port trading amount topped the world, But in the port of environmental protection sustainable development approach with foreign advanced port environmental management concept has a big gap. Combined with the present situation of modern ports in China. Drawing lessons from foreign advanced environmental protection idea of port, in order to promote the protection of port environment in our country. The experience of protection and development of foreign advanced port environment will be discussed and discussed.

United States Port Development Expenditure Report

DOT National Transportation Integrated Search

2001-12-01

This report is the eleventh in a series of reports that continues the capital expenditure survey first begun by the Port Authority of New York and New Jersey in 1956. Subsequent reports were published by the American Association of Port Authorities (...

Slide valve apparatus for internal combustion engine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taylor, B.A.; McMahan, T.O.

This patent describes an internal combustion engine including a combustion cylinder having an opening at one end thereof, a piston mounted within the cylinder for coaxial reciprocable movement, a driven crankshaft, and a connecting rod connecting the crankshaft to the cylinder for linear reciprocable movement of the piston in response to the rotary movement of the crankshaft, a valve apparatus comprising: (a) a valve chamber extending longitudinally across and in fluid communication with the opening in the cylinder, (b) an intake valve plate having a longitudinal axis mounted within the valve chamber for slidable, reciprocable, longitudinal movement, (c) an exhaustmore » valve plate having a longitudinal axis mounted within the valve chamber alongside the intake valve plate for slidable, reciprocable, longitudinal movement and parallel to the longitudinal axis of the intake valve plate, (d) each of the valve plates having a plurality of longitudinally spaced valve ports therein, the valve ports comprising movable intake valve ports in the intake valve plate and movable exhaust valve ports in the exhaust valve plate, (e) the valve chamber comprising a planar wall on the opposite side of the valve plates from the cylinder opening and having a plurality of fixed valve ports therethrough. The fixed valve ports being equal in number and substantially equal in size and spacing as the movable intake and exhaust valve ports, whereby the movable intake valve ports are adapted to register with their corresponding fixed valve ports when the intake valve plate is in its intake operative position for opening fluid communication between the cylinder and the corresponding fixed valve ports.« less

A modified method using a two-port approach for accessing the hilar vasculature without transferring an endostapler from camera port to utility port during thoracoscopic right upper lobectomy.

PubMed

Jiao, W; Zhao, Y; Xuan, Y; Wang, M

2015-02-01

For thoracoscopic upper lobectomies, most cutting endostaplers must be inserted through the camera port when using a two-port approach. Access to the hilar vasculature through only the utility port remains a challenge. In this study, we describe a procedure to access the hilar vasculature without transferring the endostapler site during a thoracoscopic right upper lobectomy. A 2.5-cm utility anterior incision was made in the fourth intercostal space. The posterior mediastinal visceral pleura were dissected to expose the posterior portion of the right upper bronchus and the anterior trunk of the right pulmonary artery. The pleura over the right hilar vasculature were then peeled with an electrocoagulation hook. The anterior trunk of the right pulmonary artery was then transected with a cutting endostapler through the utility port firstly. This crucial maneuver allowed the endostapler access to the right upper lobe pulmonary vein. The hilar structures were then easily handled in turn. This novel technique was performed successfully in 32 patients, with no perioperative deaths. The average operation time was 120.6 min (range 75-180 min). This novel technique permits effective control of the hilar vessels through the utility port, enabling simple, safe, quick and effective resection.

United States Port Development Expenditure Report

DOT National Transportation Integrated Search

1997-10-01

This report is the seventh edition in a series of reports that continues the capital expenditure survey first begun by the Port Authority of New York and New Jersey in 1956. Subsequent reports were published by the American Association of Port Author...

United States Port Development Expenditure Report

DOT National Transportation Integrated Search

2000-12-01

This report is the tenth in a series of reports that continues the capital expenditure survey first begun by the Port Authority of New York and New Jersey in 1956. Subsequent reports were published by the American Association of Port Authorities (AAP...

U.S. Offshore Wind Port Readiness

DOE Office of Scientific and Technical Information (OSTI.GOV)

C. Elkinton, A. Blatiak, H. Ameen

2013-10-13

This study will aid decision-makers in making informed decisions regarding the choice of ports for specific offshore projects, and the types of investments that would be required to make individual port facilities suitable to serve offshore wind manufacturing, installation and/or operations.

Assessing the port to port risk of vessel movements vectoring non-indigenous marine species within and across domestic Australian borders.

PubMed

Campbell, Marnie L; Hewitt, Chad L

2011-07-01

Biofouling of vessels is implicated as a high risk transfer mechanism of non-indigenous marine species (NIMS). Biofouling on international vessels is managed through stringent border control policies, however, domestic biofouling transfers are managed under different policies and legislative arrangements as they cross internal borders. As comprehensive guidelines are developed and increased compliance of international vessels with 'clean hull' expectations increase, vessel movements from port to port will become the focus of biosecurity management. A semi-quantitative port to port biofouling risk assessment is presented that evaluates the presence of known NIMS in the source port and determines the likelihood of transfer based on the NIMS association with biofouling and environmental match between source and receiving ports. This risk assessment method was used to assess the risk profile of a single dredge vessel during three anticipated voyages within Australia, resulting in negligible to low risk outcomes. This finding is contrasted with expectations in the literature, specifically those that suggest slow moving vessels pose a high to extreme risk of transferring NIMS species.

Robotic right middle lobectomy with a subxiphoid utility port.

PubMed

Jayakumar, Shruti; Nardini, Marco; Papoulidis, Pavlos; Dunning, Joel

2018-06-01

We present the case of a 74-year-old man with Stage IIa pulmonary adenocarcinoma, for which he underwent a robotic right middle lobectomy. A 4-armed, 5-port approach was used. Four intercostal ports were created above the ninth rib using the Cerfolio's technique. The subxiphoid port was created in the midline, 5 cm down from the xiphisternum. The robot offers higher image quality, depth perception and improved articulation of the instruments, allowing for more accurate dissection and stitching. The usage of a subxiphoid utility port reduces the clashing between instruments, offers a good angle for stapling and provides a direct view of the instruments entering into the chest. Specimen removal through the subxiphoid port may reduce postoperative pain and enhance patient recovery. The use of the subxiphoid approach as a utility port for robotic surgery is promising and may be a suitable replacement for the traditional utility port.

9 CFR 93.102 - Ports designated for the importation of birds.

Code of Federal Regulations, 2013 CFR

2013-01-01

... the importation of birds. (a) Special ports for pet birds. The following ports are designated as ports of entry for pet birds imported under the provisions of § 93.101(c) and performing or theatrical... § 93.105. (d) Limited ports. The following ports are designated as ports of entry for pet birds...

9 CFR 93.102 - Ports designated for the importation of birds.

Code of Federal Regulations, 2014 CFR

2014-01-01

... the importation of birds. (a) Special ports for pet birds. The following ports are designated as ports of entry for pet birds imported under the provisions of § 93.101(c) and performing or theatrical... § 93.105. (d) Limited ports. The following ports are designated as ports of entry for pet birds...

9 CFR 93.102 - Ports designated for the importation of birds.

Code of Federal Regulations, 2012 CFR

2012-01-01

... the importation of birds. (a) Special ports for pet birds. The following ports are designated as ports of entry for pet birds imported under the provisions of § 93.101(c) and performing or theatrical... § 93.105. (d) Limited ports. The following ports are designated as ports of entry for pet birds...

Hazard report. Infants may fall through insecure ports on incubators.

PubMed

2010-01-01

If the iris ports or access ports on infant incubators are not sufficiently secure, infants may work their way through the ports and fall. To reduce this risk, users should make sure that the ports are closed securely following each use. When possible, users should pass tubing through the incubator hood's grommets instead of through the larger and potentially less secure iris ports.

The VisPort Project: Visualization of Port Logistics

ERIC Educational Resources Information Center

Katsioloudis, Petros J.; Watson, Ginger

2011-01-01

There is concern about the diminishing availability of skilled personnel that can operate in the wide variety of disciplines associated with port operations. Increasing cargo volume, combined with a shrinking workforce, could potentially create alarming situations in the future, hence the motivation to publicize to current students the breadth and…

[Periinterventional prophylactic antibiotics in radiological port catheter implantation].

PubMed

Gebauer, B; Teichgräber, U; Werk, M; Wagner, H-J

2007-08-01

To evaluate whether catheter-related infections after radiologically placed port catheters can be reduced by single-shot periinterventional antibiosis. Between January and September 2002, 164 consecutive patients with indication for central venous port catheter implantation were included in the present study. During implantation the interventional radiologist was responsible for deciding whether to administer a prophylactic single-shot antibiosis. The prophylactic antibiosis entailed intravenous administration of ampicillin and sulbactam (3 g Unacid, Pfizer) or 100 mg ciprofloxacine (Ciprobay, Bayer) in the case of an allergy history to penicillins. Catheter-related infection was defined as a local or systemic infection necessitating port catheter extraction. Indication for port catheter implantation was a malignant disease requiring chemotherapy in 158 cases. The port catheter (Chemosite [Tyco Healthcare] [n = 123], low-profile [Arrow International] [n = 35], other port system [n = 6]) was implanted via sonographically guided puncture of the right jugular vein in 139 patients, via the left jugular vein in 24 cases and via the right subclavian vein in one patient. 75 patients received periinterventional prophylactic antibiosis (Unacid [n = 63] Ciprobay [n = 12]) and 89 patients did not receive antibiosis. The prophylactic antibiosis caused a minor allergic reaction in one patient that improved with antihistamic and corticoid medication. A total of 7 ports, 6 without prophylactic antibiosis versus one with periinterventional prophylaxis, were extracted due to infectious complications. Single-shot periinterventional prophylactic antibiosis can reduce early and late infectious complications after radiological-interventional placement of central venous port catheters.

An analysis of the development of port operation in Da Nang Port, Vietnam

NASA Astrophysics Data System (ADS)

Nguyen, T. D. H.; Cools, M.

2018-04-01

This paper presents the current operating status in Da Nang Port, Vietnam in the period 2012-2016. The port operation had positive changes that were reflected by a significant increase in total throughputs, especially containerized cargo volumes. Classical decomposition techniques are used to find trend-cycle and seasonal components of monthly throughput flows. Appropriate predictive models of different kinds of throughputs are proposed. Finally, a development strategy towards containerization and investment policies in facilities, equipment, and infrastructure are suggested based on the predictive results.

Ports in a storm.

PubMed

Sharma, Dinesh C

2006-04-01

In many parts of the world, shipping-related emissions have already exceeded or are expected to soon exceed those from land-based sources. Shipping emissions can be reduced substantially by using some of the same technologies being applied to land-based sources, including cleaner engines and fuels, exhaust control methods, and operational modifications. Various ports are testing the feasibility of these mechanisms with varying degrees of success. What is perhaps most greatly needed is expedited creation of better regulations at all levels, from the International Maritime Organization to port city authorities.

4. View of houses from Port Ludlow, houses no. 69 ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. View of houses from Port Ludlow, houses no. 69 and 70, facing southwest. House no. 69 in foreground, house no. 70 in background. - Houses Moved from Port Ludlow, Various Addresses (moved from Port Ludlow, WA), Port Gamble, Kitsap County, WA

One-port video-assisted thoracic surgery versus three-port video-assisted thoracic surgery for primary spontaneous pneumothorax: a meta-analysis.

PubMed

Xu, Wu; Wang, Yang; Song, Jianping; Mo, Lanying; Jiang, Tao

2017-01-01

To further understand the effects of video-assisted thoracic surgery (VATS) with one-port versus three-port VATS for primary spontaneous pneumothorax (PSP). In this study, we searched information from the PubMed, Cochrane Library, Embase, ScienceDirect, Web of Science, China National Knowledge Infrastructure (CNKI), and Wanfang Data databases from inception to September 2015 to collect data of randomized controlled trials (RCTs) and cohort studies about one-port VATS versus three-port VATS for PSP. Two independent authors were committed to screen literature, extract data, and assess the risk of bias of related studies. Then, we used the RevMan 5.20 software for a meta-analysis of one-port VATS versus three-port VATS for PSP. Six cohort studies involving 310 patients were finally selected in this meta-analysis. The results of our study indicate that one-port VATS had a shorter hospital stay (SMD = -0.39, 95 % CI -0.69 to 0.09, P = 0.01), lower VAS score of 24-h post-operative pain (SMD = -0.78, 95 % CI -1.40 to -0.52, P < 0.00001), shorter chest drainage time (SMD = -0.68, 95 % CI -1.15 to -0.22, P = 0.004), and lower incidence of post-operative paraesthesia (OR = 0.13, 95 % CI 0.06 to 0.29, P < 0.00001) compared with three-port VATS. However, one-port VATS had a lower patient satisfaction score at 24 h (SMD = -0.65, 95 % CI -0.95 to -0.35, P < 0.0001) and 48 h (SMD = -0.46, 95 % CI -0.71 to -0.21, P = 0.0002). No differences in the recurrence of pneumothorax (OR = 0.58, 95 % CI 0.20 to 1.67, P = 0.32), the operation time (SMD = 1.01, 95 % CI -4.63 to 2.60, P = 0.58), and the satisfaction score at 72 h (SMD = -0.11, 95 % CI -0.44 to 0.22, P < 0.00001) were noted between the groups. Current evidence suggests that one-port VATS may have certain advantages over three-port VATS for PSP. More large-scale and high-quality studies are needed for authentication.

33 CFR 165.T08-0432 - Safety Zone; Waterway Closure, Morgan City-Port Allen Route from Mile Marker 0 to Port Allen Lock.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., Morgan City-Port Allen Route from Mile Marker 0 to Port Allen Lock. 165.T08-0432 Section 165.T08-0432... Limited Access Areas Eighth Coast Guard District § 165.T08-0432 Safety Zone; Waterway Closure, Morgan City... Water Way on the Morgan City—Port Allen route from MM 0 to the Port Allen lock. (b) Effective date. This...

Severe Neutropenia at the Time of Implantable Subcutaneous Chest Port Insertion Is Not a Risk Factor for Port Removal at a Tertiary Pediatric Center.

PubMed

Hoss, Daniel R; Bedros, Antranik A; Mesipam, Avinash; Criddle, Jared; Smith, Jason C

2017-03-01

To determine if severe neutropenia at the time of chest port insertion is a risk factor for port removal and central catheter-associated bloodstream infection (CCABSI) in pediatric patients. From May 2007 to June 2015, 183 consecutive patients (mean age, 9.9 y; range, 0.75-21 y) had a port inserted at a single tertiary pediatric center. Seventy-two had severe neutropenia at the time of port insertion (absolute neutrophil count [ANC] range, 0-500/mm 3 ; mean, 185/mm 3 ). Follow-up until port removal or death and CCABSI events were recorded. Within the first 30 days, similar incidences of CCABSI (12.5% of patients with severe neutropenia [n = 9] vs 4.5% of patients without [n = 5]), port removal for infection (2.8% [n = 2] vs 2.7% [n = 3]), and local port infection (2.8% [n = 2] vs 0.9% [n = 1]) were observed in both groups (P > .05), but the rate of CCABSI per 1,000 catheter-days was higher for patients with severe neutropenia (P = .045). Overall, similar incidences of CCABSI (18.1% [n = 13] vs 16.2% [n = 18]), port removal for infection (2.8% [n = 2] vs 7.2% [n = 8]), local port infection (2.8% [n = 2] vs 2.7% [n = 3]), and CCABSIs per 1,000 catheter-days (0.332 vs 0.400) were observed in both groups (P > .05). Port placement in patients with severe neutropenia can be performed without an increased incidence of port removal for infection. The majority of CCABSIs were successfully treated without port removal. Copyright © 2016 SIR. Published by Elsevier Inc. All rights reserved.

Research-based resources on PhysPort

NASA Astrophysics Data System (ADS)

Sayre, Eleanor

2017-01-01

PhysPort (http://physport.org) is a website that supports physics faculty in implementing research-based teaching practices in their classrooms. We provide expert recommendations and practical information about teaching methods and assessment. The PhysPort Data Explorer is an intuitive online tool for physics faculty to analyze their assessment data. Faculty upload their students' responses using our secure interface. The Data Explorer matches their pre/post data, scores it, compares it to national data, and graphs it in an interactive and intuitive manner. The Periscope collection on Physport brings together classroom video of students working groups with professional development materials for faculty, pre-service teachers, and learning assistants. To support PhysPort's development efforts, we conduct research on faculty needs around teaching and assessment, secondary analysis of published PER studies, and primary analysis of assessment data. In this talk, I'll introduce some of PhysPort's research-based resources and the research results which support them.

Air flow quality analysis of modenas engine exhaust system

NASA Astrophysics Data System (ADS)

Shahriman A., B.; Mohamad Syafiq A., K.; Hashim, M. S. M.; Razlan, Zuradzman M.; Khairunizam W. A., N.; Hazry, D.; Afendi, Mohd; Daud, R.; Rahman, M. D. Tasyrif Abdul; Cheng, E. M.; Zaaba, S. K.

2017-09-01

The simulation process being conducted to determine the air flow effect between the original exhaust system and modified exhaust system. The simulations are conducted to investigate the flow distribution of exhaust gases that will affect the performance of the engine. The back flow pressure in the original exhaust system is predicted toward this simulation. The design modification to the exhaust port, exhaust pipe, and exhaust muffler has been done during this simulation to reduce the back flow effect. The new designs are introduced by enlarging the diameter of the exhaust port, enlarge the diameter of the exhaust pipe and created new design for the exhaust muffler. Based on the result obtained, there the pulsating flow form at the original exhaust port that will increase the velocity and resulting the back pressure occur. The result for new design of exhaust port, the velocity is lower at the valve guide in the exhaust port. New design muffler shows that the streamline of the exhaust flow move smoothly compare to the original muffler. It is proved by using the modification exhaust system, the back pressure are reduced and the engine performance can be improve.

40 CFR 1065.670 - NOX intake-air humidity and temperature corrections.

Code of Federal Regulations, 2012 CFR

2012-07-01

... combustion air humidity to calculate this correction if your combustion air humidity remains within a...-air humidity. You may use a time-weighted mean combustion air humidity to calculate this correction if your combustion air humidity remains within a tolerance of ±0.0025 mol/mol of the mean value over the...

40 CFR 1065.670 - NOX intake-air humidity and temperature corrections.

Code of Federal Regulations, 2013 CFR

2013-07-01

... combustion air humidity to calculate this correction if your combustion air humidity remains within a...-air humidity. You may use a time-weighted mean combustion air humidity to calculate this correction if your combustion air humidity remains within a tolerance of ±0.0025 mol/mol of the mean value over the...

40 CFR 1065.670 - NOX intake-air humidity and temperature corrections.

Code of Federal Regulations, 2014 CFR

2014-07-01

... combustion air humidity to calculate this correction if your combustion air humidity remains within a...-air humidity. You may use a time-weighted mean combustion air humidity to calculate this correction if your combustion air humidity remains within a tolerance of ±0.0025 mol/mol of the mean value over the...

Physical Oceanographic Real-Time System (PORTS) (Invited)

NASA Astrophysics Data System (ADS)

Wright, D.

2013-12-01

The 1999 Assessment of U.S. Marine Transportation System report to Congress noted that the greatest safety concern voiced by the maritime community was the availability of timely, accurate, and reliable navigation information, including real time environment data. Real time oceanographic and meteorological data, along with other navigation tools, gives the mariner a good situational understanding of their often challenging operational environment, to make the best safety of life and property decisions. The National Oceanic and Atmospheric Administration's (NOAA) Physical Oceanographic Real Time System (PORTS) was developed in response to accidents like the Sunshine Skyway Bridge collision in Tampa, FL in 1980, where the lack of accurate, reliable and timely environmental conditions directly contributed to an accident that resulted in a high loss of life and property. Since that time, PORTS has expanded to over 20 locations around the country, and its capabilities have been continually expanded and improved as well. PORTS primary mission is to prevent maritime accidents. Preventing an accident from occurring is the most cost effective approach and the best way to avoid damage to the environment. When accidents do occur, PORTS data is used to improve the effectiveness of response efforts by providing input for trajectory models and real time conditions for response efforts. However, benefits derived from PORTS go well beyond navigation safety. Another large benefit to the local maritime community is potential efficiencies in optimizing use of the existing water column. PORTS provides information that can be used to make economic decisions to add or offload cargo to a vessel and/or to maintain or adjust transit schedules based upon availability of water depth, strength/timing of tidal currents, and other conditions. PORTS data also helps improve and validate local National Weather Service marine weather forecasts. There are many benefits beyond the local maritime

Single-port laparoscopic myomectomy using a new single-port transumbilical morcellation system: initial clinical study.

PubMed

Kim, Yong-Wook; Park, Byung-Joon; Ro, Duck-Yeong; Kim, Tae-Eung

2010-01-01

To evaluate the feasibility of single-port laparoscopic myomectomy with transumbilical morcellation and suturing. Continuing prospective study (Canadian Task Force classification II-3). University hospital. Fifteen patients who underwent single-port laparoscopic myomectomy between September 2008 and October 2009 to remove single or multiple uterine myomas, at least 1 in each patient measuring greater than 4 cm in diameter. All single-port laparoscopic myomectomy procedures were performed by a single surgeon (Dr. Y.W. Kim). Myomas were extracted transumbilically by cutting the myomas into smaller pieces with a knife or a conventional electromechanical morcellator. After making a single 1.5- to 2.0-cm umbilical incision, the single-port system, created with a wound retractor and a surgical glove, was inserted. All operations were performed using conventional rigid straight laparoscopic instruments. Laparoscopic suturing was performed in intramural myomas and some subserosal myomas. Patient mean (SD; range) age was 38.3 (5.6; 29-49) years. The number of myomas per patient was 1.6 (1.4; 1-6). The diameter of the largest myomas was 6.1 (1.5; 4.2-9.6) cm. In 4 patients, only a knife was required for transumbilical extraction of myomas, and in 11 patients, transumbilical morcellation with an electromechanical morcellator with or without a knife was used. Transumbilical drainage tubes were inserted into the pelvic cavity in 11 of 15 patients. Operative time was 96.7 (33.8; 35-150) minutes. The decrease in postoperative hemoglobin concentration was 1.8 (1.2; 0.4-3.6) g/dL. During the operations, no patients required blood transfusion. No patients developed postoperative fever. Neither bowel injury nor urinary tract injury occurred in any patient. The postoperative hospital stay was 3.1 (0.8; 2-4) days. Single-port transumbilical morcellation using a conventional electromechanical morcellator with or without a knife is feasible. Single-port laparoscopic myomectomy is an

Intracorporeal hybrid single port vs conventional laparoscopic appendectomy in children.

PubMed

Karam, Paul Anthony; Hiuser, Amy; Magnuson, David; Seifarth, Federico Gian Filippo

2016-12-20

Transumbilical laparoscopic assisted appendectomy combines laparoscopic single port dissection with open appendectomy after exteriorization of the appendix through the port site. Compared to the conventional three-port approach, this technique provides an alternative with excellent cosmetic outcome. We developed a safe and effective technique to perform an intracorporeal single port appendectomy, using the same laparoscope employed in the extracorporeal procedure. Retrospective review of 71 consecutively performed intracorporeal single port appendectomies and 30 conventional three-port appendectomies in children 6 to 17 years of age. A straight 10-mm Storz telescope with inbuilt 6 mm working channel is used to dissect the appendix, combined with one port-less 2.3 mm percutaneous grasper. Polymer WECK® hem-o-lock® clips are applied to seal the base of the appendix and the appendiceal vessels. No intraoperative complications were reported with the hybrid intracorporeal single port appendectomy or three-port appendectomy. There were two post-operative complications in the group treated with the single port hybrid technique: one intra-abdominal abscess and one surgical site infection. Groups did not differ in age, weight, and types of appendicitis. Operative times were shorter for the hybrid technique (70 vs 79 minutes) but did not differ significantly (P=0.19). This modified technique to a previously described single port extracorporeal appendectomy is easy to master and implement. It provides exposure similar to a three-port laparoscopic appendectomy, while maintaining virtually scarless results and potentially reduces the risk for surgical site infections compared to the extracorporeal technique.

Porting of EPICS to Real Time UNIX, and Usage Ported EPICS for FEL Automation

NASA Astrophysics Data System (ADS)

Salikova, Tatiana

This article describes concepts and mechanisms used in porting of EPICS (Experimental Physical and Industrial Control System) codes to platform of operating system UNIX. Without destruction of EPICS architecture, new features of EPICS provides the support for real time operating system LynxOS/x86 and equipment produced by INP (Budker Institute of Nuclear Physics). Application of ported EPICS reduces the cost of software and hardware is used for automation of FEL (Free Electron Laser) complex.

4. View of Port Gamble residential district, facing northwest across ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. View of Port Gamble residential district, facing northwest across Rainier Avenue. Thompson House in foreground, house no. 17A in right background. - Port Gamble National Historic Landmark, Bounded by Hood Canal, Port Gamble Bay, State Road 104, & Town Limits, Port Gamble, Kitsap County, WA

14 CFR 23.1091 - Air induction system.

Code of Federal Regulations, 2010 CFR

2010-01-01

... and their accessories must supply the air required by that engine and auxiliary power unit and their... cowling if the emergence of backfire flames will result in a hazard. (3) The supplying of air to the engine through the alternate air intake system may not result in a loss of excessive power in addition to...

Robotics for port security

NASA Astrophysics Data System (ADS)

Smuda, William; Freiburger, Lonnie A.; Gerhart, Grant R.; Mallon, Lawrence

2004-09-01

The capacity through the use of robots with on board visual, NBC and HAZMAT sensors to rapidly and continuously screen convoys and staged exposed assets would be a force multiplier and measurably improve base and force protection at both inbound and outbound DOD and commercial facilities. This paper chronicles our experiment with the ODIS robot at the Ports of Los Angeles (POLA) and Long Beach (POLB) in July of 2003. POLA & POLB are responsible for moving over 30% of the United States trade goods. Queues of 54" container trucks routinely exceed 100 trucks, extending for over a mile from the port entrances. Spotted equipment and convoys at staging areas are a high visibility and value assets to a terrorist incident. The POLA/POLB scenario is also representative of TRANSCOM operations at the port of Basra during current operation in Iraq. The California Highway Patrol is responsible for physically inspecting these vehicles for roadworthiness and contraband, a dangerous and dirty job. We will also discuss the use of ODIS robots for this task.

Central Vein Dilatation Prior to Concomitant Port Implantation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krombach, Gabriele A., E-mail: krombach@rad.rwth-aachen.de; Plumhans, Cedric; Goerg, Fabian

2010-04-15

Implantation of subcutaneous port systems is routinely performed in patients requiring repeated long-term infusion therapy. Ultrasound- and fluoroscopy-guided implantation under local anesthesia is broadly established in interventional radiology and has decreased the rate of complications compared to the surgical approach. In addition, interventional radiology offers the unique possibility of simultaneous management of venous occlusion. We present a technique for recanalization of central venous occlusion and angioplasty combined with port placement in a single intervention which we performed in two patients. Surgical port placement was impossible owing to occlusion of the superior vena cava following placement of a cardiac pacemaker andmore » occlusion of multiple central veins due to paraneoplastic coagulopathy, respectively. In both cases the affected vessel segments were dilated with balloon catheters and the port systems were placed thereafter. After successful dilatation, the venous access was secured with a 25-cm-long, 8-Fr introducer sheath, a subcutaneous pocket prepared, and the port catheter tunneled to the venipuncture site. The port catheter was introduced through the sheath with the proximal end connected to a 5-Fr catheter. This catheter was pulled through the tunnel in order to preserve the tunnel and, at the same time, allow safe removal of the long sheath over the wire. The port system functioned well in both cases. The combination of recanalization and port placement in a single intervention is a straightforward alternative for patients with central venous occlusion that can only be offered by interventional radiology.« less

50 CFR 300.188 - Ports of entry.

Code of Federal Regulations, 2010 CFR

2010-10-01

... International Trade Documentation and Tracking Programs for Highly Migratory Species § 300.188 Ports of entry... United States. If NMFS determines that the diversity of handling practices at certain ports at which fish...

50 CFR 300.188 - Ports of entry.

Code of Federal Regulations, 2011 CFR

2011-10-01

... International Trade Documentation and Tracking Programs for Highly Migratory Species § 300.188 Ports of entry... United States. If NMFS determines that the diversity of handling practices at certain ports at which fish...

Modeling and Control Systems Design for Air Intake System of Diesel Engines for Improvement of Transient Characteristic

NASA Astrophysics Data System (ADS)

Ejiri, Arata; Sasaki, Jun; Kinoshita, Yusuke; Fujimoto, Junya; Maruyama, Tsugito; Shimotani, Keiji

For the purpose of contributing to global environment protection, several research studies have been conducted involving clean-burning diesel engines. In recent diesel engines with Exhaust Gas Recirculation (EGR) systems and a Variable Nozzle Turbocharger (VNT), mutual interference between EGR and VNT has been noted. Hence, designing and adjusting control of the conventional PID controller is particularly difficult at the transient state in which the engine speed and fuel injection rate change. In this paper, we formulate 1st principal model of air intake system of diesel engines and transform it to control oriented model including an engine steady state model and a transient model. And we propose a model-based control system with the LQR Controller, Saturation Compensator, the Dynamic Feed-forward and Disturbance Observer using a transient model. Using this method, we achieved precise reference tracking and emission reduction in transient mode test with the real engine evaluations.

Evaluation of correlations between underlying disease and port complications.

PubMed

Teichgräber, U; Nagel, S N; Kausche, S

2014-05-01

Evaluation of correlations between underlying disease and port complications. Retrospective analysis of a data set of 3160 port systems, which had been interventionally implanted over a period of 10 years. Of these, 1393 were included in the final evaluation. The 7 most common underlying diseases and port-induced complications were considered. Port-related thrombotic events, port pocket infections as well as the port-induced sepsis were evaluated and classified as either early or late complications. In 1393 ports, 131 experienced complications. Of these, 22.1 % (n = 29) were early and 79.6 % (n = 102) late complications. The overall incidence rate of late complications was 0.253/1000 observed days. It differed significantly between the underlying diseases (p < 0.001) and was significantly lower in colon carcinoma when compared with pancreatic (p = 0.049), gastric (p = 0.012) and bronchial carcinoma (p = 0.042). The incidence rate of the port sepsis between the underlying diseases also differed significantly (p =  0.006) and had the highest rate in gastric and bronchial carcinoma. The occurrence of a thrombotic event also showed a significant difference in the incidence rates between the underlying diseases (p = 0.045) and was highest in pancreatic and gastric carcinoma. There are significant differences in the incidences of complications between the underlying diseases. Knowledge about this can help to improve the port-care and to take specific preventive measures. © Georg Thieme Verlag KG Stuttgart · New York.

Simulation model for port shunting yards

NASA Astrophysics Data System (ADS)

Rusca, A.; Popa, M.; Rosca, E.; Rosca, M.; Dragu, V.; Rusca, F.

2016-08-01

Sea ports are important nodes in the supply chain, joining two high capacity transport modes: rail and maritime transport. The huge cargo flows transiting port requires high capacity construction and installation such as berths, large capacity cranes, respectively shunting yards. However, the port shunting yards specificity raises several problems such as: limited access since these are terminus stations for rail network, the in-output of large transit flows of cargo relatively to the scarcity of the departure/arrival of a ship, as well as limited land availability for implementing solutions to serve these flows. It is necessary to identify technological solutions that lead to an answer to these problems. The paper proposed a simulation model developed with ARENA computer simulation software suitable for shunting yards which serve sea ports with access to the rail network. Are investigates the principal aspects of shunting yards and adequate measures to increase their transit capacity. The operation capacity for shunting yards sub-system is assessed taking in consideration the required operating standards and the measure of performance (e.g. waiting time for freight wagons, number of railway line in station, storage area, etc.) of the railway station are computed. The conclusion and results, drawn from simulation, help transports and logistics specialists to test the proposals for improving the port management.

Water quality assessment of Australian ports using water quality evaluation indices

PubMed Central

Jahan, Sayka

2017-01-01

Australian ports serve diverse and extensive activities, such as shipping, tourism and fisheries, which may all impact the quality of port water. In this work water quality monitoring at different ports using a range of water quality evaluation indices was applied to assess the port water quality. Seawater samples at 30 stations in the year 2016–2017 from six ports in NSW, Australia, namely Port Jackson, Botany, Kembla, Newcastle, Yamba and Eden, were investigated to determine the physicochemical and biological variables that affect the port water quality. The large datasets obtained were designed to determine the Water Quality Index, Heavy metal Evaluation Index, Contamination Index and newly developed Environmental Water Quality Index. The study revealed medium water quality index and high and medium heavy metal evaluation index at three of the study ports and high contamination index in almost all study ports. Low level dissolved oxygen and higher level of total dissolved solids, turbidity, fecal coliforms, copper, iron, lead, zinc, manganese, cadmium and cobalt are mainly responsible for the poor water qualities of the port areas. Good water quality at the background samples indicated that various port activities are the likely cause for poor water quality inside the port area. PMID:29244876

33 CFR 150.940 - Safety zones for specific deepwater ports.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 33 Navigation and Navigable Waters 2 2012-07-01 2012-07-01 false Safety zones for specific... SECURITY (CONTINUED) DEEPWATER PORTS DEEPWATER PORTS: OPERATIONS Safety Zones, No Anchoring Areas, and Areas To Be Avoided § 150.940 Safety zones for specific deepwater ports. (a) Louisiana Offshore Oil Port...

33 CFR 150.940 - Safety zones for specific deepwater ports.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 2 2011-07-01 2011-07-01 false Safety zones for specific... SECURITY (CONTINUED) DEEPWATER PORTS DEEPWATER PORTS: OPERATIONS Safety Zones, No Anchoring Areas, and Areas To Be Avoided § 150.940 Safety zones for specific deepwater ports. (a) Louisiana Offshore Oil Port...

33 CFR 150.940 - Safety zones for specific deepwater ports.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Safety zones for specific... SECURITY (CONTINUED) DEEPWATER PORTS DEEPWATER PORTS: OPERATIONS Safety Zones, No Anchoring Areas, and Areas To Be Avoided § 150.940 Safety zones for specific deepwater ports. (a) Louisiana Offshore Oil Port...

33 CFR 150.940 - Safety zones for specific deepwater ports.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 2 2013-07-01 2013-07-01 false Safety zones for specific... SECURITY (CONTINUED) DEEPWATER PORTS DEEPWATER PORTS: OPERATIONS Safety Zones, No Anchoring Areas, and Areas To Be Avoided § 150.940 Safety zones for specific deepwater ports. (a) Louisiana Offshore Oil Port...

33 CFR 150.940 - Safety zones for specific deepwater ports.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 33 Navigation and Navigable Waters 2 2014-07-01 2014-07-01 false Safety zones for specific... SECURITY (CONTINUED) DEEPWATER PORTS DEEPWATER PORTS: OPERATIONS Safety Zones, No Anchoring Areas, and Areas To Be Avoided § 150.940 Safety zones for specific deepwater ports. (a) Louisiana Offshore Oil Port...

Midterm outcomes of single port thoracoscopic surgery for major pulmonary resection

PubMed Central

2017-01-01

Introduction Single-port thoracoscopic surgery has widened the current minimally invasive surgical techniques toward more less invasive procedures in terms of reducing the number of incisions. However, the current status of oncologic outcome with this technique is not well known for lung cancer surgery. The purpose of this study is to evaluate the oncologic outcomes in early stage lung cancer for impact of the survival outcomes with our experience of conversion to a single-port approach from the conventional three-port approach. Materials and methods Retrospective data of patients who underwent thoracoscopic major lung resection for non-small cell lung cancer between January 2006 and June 2015 were analyzed. Patients’ characteristics, perioperative outcomes, pathologic result, and postoperative follow-up data of thoracoscopic surgery were reviewed and surgical outcomes were compared between conventional three-port (n = 168), two-port (n = 68), and single-port thoracoscopic surgery (n = 203). Results Of the 203 single-port thoracoscopic surgeries, we performed 167 single-port thoracoscopic lobectomy and mediastinal lymph node dissections. During the learning period of each thoracoscopic approach, the mean operation time for single-port thoracoscopic surgery (189±62 min) was not significantly different from those of two-port (175±46 min) and three-port (195±75 min) thoracoscopic lobectomy (p = 0.165). Perioperative outcomes including drain indwelling time (p <0.001), complication (p = 0.185) and conversion event (p = 0.911) were not worsened during learning period with two-port. Midterm survival (p = 0.753) and recurrence free survival (p = 0.656) of single port thoracoscopic lobectomy showed acceptable results compared with two- and three-port approach. Conclusions Single-port thoracoscopic surgery is safe and a feasible option for major lung resection in lung malignancy and this approach following experiences of two-port approach may yield similar oncologic

Optimal port-based teleportation

NASA Astrophysics Data System (ADS)

Mozrzymas, Marek; Studziński, Michał; Strelchuk, Sergii; Horodecki, Michał

2018-05-01

Deterministic port-based teleportation (dPBT) protocol is a scheme where a quantum state is guaranteed to be transferred to another system without unitary correction. We characterise the best achievable performance of the dPBT when both the resource state and the measurement is optimised. Surprisingly, the best possible fidelity for an arbitrary number of ports and dimension of the teleported state is given by the largest eigenvalue of a particular matrix—Teleportation Matrix. It encodes the relationship between a certain set of Young diagrams and emerges as the optimal solution to the relevant semidefinite programme.

A Comparison of Single-, Two- and Three-Port Laparoscopic Myomectomy

PubMed Central

Kim, Su Mi; Baek, Jong Min; Park, Eun Kyung; Jeung, In Cheul; Choi, Ji Hyang; Kim, Chan Joo

2015-01-01

Background and Objective: A recent FDA safety communication has discouraged the use of a power morcellator for myoma extraction and has called for a change in surgical techniques for myomectomy. The objective of this study was to compare surgical outcomes of laparoscopic single-, two-, and conventional three-port myomectomy and to evaluate the feasibility of contained manual morcellation for uterine myoma. Methods: This retrospective study was a review and analysis of data from 191 consecutive women who underwent single-, two-, or three-port myomectomy for the management of uterine myoma from January 1, 2009, through December 31, 2014. Results: The 3 study groups did not differ demographically. Apart from operative time, the single- and two-port groups showed operative outcomes comparable to those of the multiport group. The single-port group had significantly longer operative times (P = .0053) than the two- and three-port groups. However, in the latter half of the single-port cases, the operative time was similar to those in the three-port group. The two-port surgery group showed a consistent operative time without a learning period. Conclusion: Single- or two-port myomectomy with transumbilical myoma morcellation is feasible and safe, with outcomes comparable to those of three-port myomectomy. These results suggest the potential for minimally invasive management of symptomatic uterine myoma, without the use of a power morcellator. PMID:26648680

A black carbon air quality network

NASA Astrophysics Data System (ADS)

Kirchstetter, T.; Caubel, J.; Cados, T.; Preble, C.; Rosen, A.

2016-12-01

We developed a portable, power efficient black carbon sensor for deployment in an air quality network in West Oakland, California. West Oakland is a San Francisco Bay Area residential/industrial community adjacent to regional port and rail yard facilities, and is surrounded by major freeways. As such, the community is affected by diesel particulate matter emissions from heavy-duty diesel trucks, locomotives, and ships associated with freight movement. In partnership with Environmental Defense Fund, the Bay Area Air Quality Management District, and the West Oakland Environmental Indicators Project, we are collaborating with community members to build and operate a 100-sensor black carbon measurement network for a period of several months. The sensor employs the filter-based light transmission method to measure black carbon. Each sensor node in the network transmits data hourly via SMS text messages. Cost, power consumption, and performance are considered in choosing components (e.g., pump) and operating conditions (e.g., sample flow rate). In field evaluation trials over several weeks at three monitoring locations, the sensor nodes provided black carbon concentrations comparable to commercial instruments and ran autonomously for a week before sample filters and rechargeable batteries needed to be replaced. Buildup to the 100-sensor network is taking place during Fall 2016 and will overlap with other ongoing air monitoring projects and monitoring platforms in West Oakland. Sensors will be placed along commercial corridors, adjacent to freeways, upwind of and within the Port, and throughout the residential community. Spatial and temporal black carbon concentration patterns will help characterize pollution sources and demonstrate the value of sensing networks for characterizing intra-urban air pollution concentrations and exposure to air pollution.

Patient-specific port placement for laparoscopic surgery using atlas-based registration

NASA Astrophysics Data System (ADS)

Enquobahrie, Andinet; Shivaprabhu, Vikas; Aylward, Stephen; Finet, Julien; Cleary, Kevin; Alterovitz, Ron

2013-03-01

Laparoscopic surgery is a minimally invasive surgical approach, in which abdominal surgical procedures are performed through trocars via small incisions. Patients benefit by reduced postoperative pain, shortened hospital stays, improved cosmetic results, and faster recovery times. Optimal port placement can improve surgeon dexterity and avoid the need to move the trocars, which would cause unnecessary trauma to the patient. We are building an intuitive open source visualization system to help surgeons identify ports. Our methodology is based on an intuitive port placement visualization module and atlas-based registration algorithm to transfer port locations to individual patients. The methodology follows three steps:1) Use a port placement visualization module to manually place ports in an abdominal organ atlas. This step generates port-augmented abdominal atlas. This is done only once for a given patient population. 2) Register the atlas data with the patient CT data, to transfer the prescribed ports to the individual patient 3) Review and adjust the transferred port locations using the port placement visualization module. Tool maneuverability and target reachability can be tested using the visualization system. Our methodology would decrease the amount of physician input necessary to optimize port placement for each patient case. In a follow up work, we plan to use the transferred ports as starting point for further optimization of the port locations by formulating a cost function that will take into account factors such as tool dexterity and likelihood of collision between instruments.

Phytoplankton diversity in Adriatic ports: Lessons from the port baseline survey for the management of harmful algal species.

PubMed

Mozetič, Patricija; Cangini, Monica; Francé, Janja; Bastianini, Mauro; Bernardi Aubry, Fabrizio; Bužančić, Mia; Cabrini, Marina; Cerino, Federica; Čalić, Marijeta; D'Adamo, Raffaele; Drakulović, Dragana; Finotto, Stefania; Fornasaro, Daniela; Grilli, Federica; Kraus, Romina; Kužat, Nataša; Marić Pfannkuchen, Daniela; Ninčević Gladan, Živana; Pompei, Marinella; Rotter, Ana; Servadei, Irene; Skejić, Sanda

2017-12-30

An inventory of phytoplankton diversity in 12 Adriatic ports was performed with the port baseline survey. Particular emphasis was put on the detection of harmful aquatic organisms and pathogens (HAOP) because of their negative impact on ecosystem, human health, and the economy. Phytoplanktonic HAOP are identified as species, either native or non-indigenous (NIS), which can trigger harmful algal blooms (HAB). A list of 691 taxa was prepared, and among them 52 were classified as HAB and five as NIS. Records of toxigenic NIS (Pseudo-nitzschia multistriata, Ostreopsis species including O. cf. ovata) indicate that the intrusion of non-native invasive phytoplankton species has already occurred in some Adriatic ports. The seasonal occurrence and abundance of HAOP offers a solid baseline for a monitoring design in ports in order to prevent ballast water uptake and possible expansion of HAOP outside their native region. Copyright © 2017 Elsevier Ltd. All rights reserved.

33 CFR 165.761 - Security Zones; Port of Palm Beach, Port Everglades, Port of Miami, and Port of Key West, Florida.

Code of Federal Regulations, 2010 CFR

2010-07-01

... all waters between Watson Park and Star Island on the MacArthur Causeway south to the Port of Miami...′ N, 080°10.92′ W to 25°46.88′ N, 080°10.84′ W, and ending on Watson Park at 25°47.00′ N, 080°10.67′ W...

33 CFR 165.761 - Security Zones; Port of Palm Beach, Port Everglades, Port of Miami, and Port of Key West, Florida.

Code of Federal Regulations, 2011 CFR

2011-07-01

... all waters between Watson Park and Star Island on the MacArthur Causeway south to the Port of Miami...′ N, 080°10.92′ W to 25°46.88′ N, 080°10.84′ W, and ending on Watson Park at 25°47.00′ N, 080°10.67′ W...

33 CFR 165.761 - Security Zones; Port of Palm Beach, Port Everglades, Port of Miami, and Port of Key West, Florida.

Code of Federal Regulations, 2014 CFR

2014-07-01

... all waters between Watson Park and Star Island on the MacArthur Causeway south to the Port of Miami...′ N, 080°10.92′ W to 25°46.88′ N, 080°10.84′ W, and ending on Watson Park at 25°47.00′ N, 080°10.67′ W...

33 CFR 165.761 - Security Zones; Port of Palm Beach, Port Everglades, Port of Miami, and Port of Key West, Florida.

Code of Federal Regulations, 2012 CFR

2012-07-01

... all waters between Watson Park and Star Island on the MacArthur Causeway south to the Port of Miami...′ N, 080°10.92′ W to 25°46.88′ N, 080°10.84′ W, and ending on Watson Park at 25°47.00′ N, 080°10.67′ W...

33 CFR 165.761 - Security Zones; Port of Palm Beach, Port Everglades, Port of Miami, and Port of Key West, Florida.

Code of Federal Regulations, 2013 CFR

2013-07-01

... all waters between Watson Park and Star Island on the MacArthur Causeway south to the Port of Miami...′ N, 080°10.92′ W to 25°46.88′ N, 080°10.84′ W, and ending on Watson Park at 25°47.00′ N, 080°10.67′ W...

7. View of Port Gamble residential district, facing northwest across ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. View of Port Gamble residential district, facing northwest across intersection of Rainier Avenue with Pope Street. House no. 11 in left foreground, Jackson House, house no. 10 in center foreground. - Port Gamble National Historic Landmark, Bounded by Hood Canal, Port Gamble Bay, State Road 104, & Town Limits, Port Gamble, Kitsap County, WA

5. View of Port Gamble residential district, facing northwest across ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. View of Port Gamble residential district, facing northwest across Rainier Avenue, house no. 16A in left foreground, house no. 16 in center, house no. 15 in right background. - Port Gamble National Historic Landmark, Bounded by Hood Canal, Port Gamble Bay, State Road 104, & Town Limits, Port Gamble, Kitsap County, WA

Integration of air separation membrane and coalescing filter for use on an inlet air system of an engine

DOEpatents

Moncelle, Michael E.

2003-01-01

An intake air separation system suitable for combustion air of an internal combustion engine. An air separation device of the system includes a plurality of fibers, each fiber having a tube with a permeation barrier layer on the outer surface thereof and a coalescing layer on the inner surface thereof, to restrict fluid droplets from contacting the permeation barrier layer.

Phytophthora lateralis on Port-Orford-cedar.

Treesearch

John Hunt

1959-01-01

Results from annual surveys of the destructive Phytophthora root disease of Port-Orford-cedar (Chamaecyparis lawsoniana (A. Murr.) Parl.) show that the disease is gradually spreading and intensifying within the natural range of Port-Orford-cedar. The disease became established on native trees in the early 1950's in the vicinity of Coos Bay,...

Radiation exposure related to the shipment of fertilisers to and from commercial ports: the case study of the seaport of Ravenna (Italy).

PubMed

Righi, Serena; Lucialli, Patrizia; Pollini, Elisa

2014-03-01

This paper presents the results of a study of radiological impacts related to the shipment of fertilisers to and from the commercial port of Ravenna (NE Italy). In particular, the effective doses to the port workers and members of the population surrounding the port area have been estimated. The study has included different types of measurement and assessment. First, the natural radioactivity of different fertilisers moving through the port has been determined: (40)K, (226)Ra, (210)Pb, (228)Ra and (228)Th concentrations have been analysed using γ-ray spectrometry, while (238)U and (232)Th concentrations have been determined by ICP-MS. At the same time, a dose rate meter and electret ion chambers were used to measure the external irradiation and the radon concentrations, respectively. Then, air pollutant dispersion models have been applied in order to assess particulate matter concentration in the port site and the surrounding residential areas, and consequently the inhalation doses. Finally, the annual effective doses to workers and local residents have been estimated. The effective doses to workers and the population have been estimated to be 0.9 mSv yr(-1) and 0.07 μSv yr(-1), respectively.

Freight movement, port facilities, and economic competitiveness.

DOT National Transportation Integrated Search

2014-07-01

This research report examines how the Panama Canal expansion will affect freight at three ports, truck movement : between the ports and inland economic hubs and the economic impacts accompanying the shift in cargo shipping : patterns. Economic impact...

Single-port laparoscopic and robotic partial nephrectomy.

PubMed

Kaouk, Jihad H; Goel, Raj K

2009-05-01

Partial nephrectomy (PN) for small renal masses provides effective oncologic outcomes. Single-port laparoscopic (SPL) and robotic surgeries are evolving approaches to advance minimally invasive surgery. To determine the feasibility of laparoscopic and robotic single-port PN. Since 2007, evaluation of patients undergoing SPL and single-port robotic (SPR) PN at a primary referral center was performed. Patients with small, solitary, exophytic-enhancing renal masses were selected. Patients with a solitary kidney, endophytic or hilar tumors, and previous abdominal and/or kidney surgery were excluded. Perioperative and pathologic data were entered prospectively into an institutional review board (IRB)-approved database. Tumor location determined either an open Hasson transperitoneal or retroperitoneal approach. A single multichannel port or Triport provided intra-abdominal access. The Harmonic Scalpel was used for tumor excision under normal renal perfusion. The da Vinci surgical robot was used for SPR cases. Patient demographics, perioperative, hematologic, and pathologic data as well as pain assessment using the Visual Analog Pain Scale (VAPS) were assessed. A total of seven patients underwent single-port PN (SPL=5, SPR=2). One patient with a right anterior upper-pole mass required conversion from SPL to standard laparoscopy following tumor excision because of intraoperative bleeding. Pathology revealed six lesions compatible with renal cell carcinoma (RCC) and one benign cyst. One negative frozen section came back focally positive on final histopathology. All other surgical margins were negative. A mean difference of 3.0+/-2.0 g/dl in hemoglobin was noted in all patients. Minimal pain was noted at discharge following both laparoscopic and robotic single-port surgery (VAPS=1.7+/-1.2 vs 1+/-0.5/10). SPL and SPR PN is feasible for select exophytic tumors. Robotics may improve surgical capabilities during single-port surgery.

Development and Characterization Testing of an Air Pulsation Valve for a Pulse Detonation Engine Supersonic Parametric Inlet Test Section

NASA Technical Reports Server (NTRS)

Tornabene, Robert

2005-01-01

In pulse detonation engines, the potential exists for gas pulses from the combustor to travel upstream and adversely affect the inlet performance of the engine. In order to determine the effect of these high frequency pulses on the inlet performance, an air pulsation valve was developed to provide air pulses downstream of a supersonic parametric inlet test section. The purpose of this report is to document the design and characterization tests that were performed on a pulsation valve that was tested at the NASA Glenn Research Center 1x1 Supersonic Wind Tunnel (SWT) test facility. The high air flow pulsation valve design philosophy and analyses performed are discussed and characterization test results are presented. The pulsation valve model was devised based on the concept of using a free spinning ball valve driven from a variable speed electric motor to generate air flow pulses at preset frequencies. In order to deliver the proper flow rate, the flow port was contoured to maximize flow rate and minimize pressure drop. To obtain sharp pressure spikes the valve flow port was designed to be as narrow as possible to minimize port dwell time.

An analytical and experimental study of injection-locked two-port oscillators

NASA Technical Reports Server (NTRS)

Freeman, Jon C.; Downey, Alan N.

1987-01-01

A Ku-band IMPATT oscillator with two distinct output power ports was injection-locked alternately at both ports. The transmission locking bandwidth was nearly the same for either port. The lower free running power port had a reflection locking bandwidth that was narrower than its transmission locking one. Just the opposite was found at the other port. A detailed analytical model for two-port injection-locked oscillators is presented, and its results agree quite well with the experiments. A critique of the literature on this topic is included to clear up misconceptions and errors. It is concluded that two-port injection-locked oscillators may prove useful in certain communication systems.

Image-guided placement of port catheters: is there an increased risk of infection if the port is immediately accessed and used?

PubMed

Salazar, Gloria; Yeddula, Kalpana; Wicky, Stephan; Oklu, Ramhi; Ganguli, Suvranu; Waltman, Arthur C; Walker, Thomas G; Kalva, Sanjeeva P

2013-01-01

To compare complication rates in patients who have port-a-catheters inserted and left accessed for immediate use and those who have ports inserted but not accessed. In this retrospective, IRB-approved study, medical records of patients who received a port catheter between 9/2009 and 2/2010 were reviewed. The data collected included patient demographics, diagnosis, procedure and complications. The patients were categorized into two groups: accessed (patients in whom the port was accessed with a Huber needle for immediate intravenous use and the patient left the procedure area with needle indwelling) and control (patients in whom the ports were not accessed). Complications were classified according to Society of Interventional Radiology guidelines. Results are given as mean ±SD. Statistical analysis was performed with student t test and statistical significance was considered at P<.05. A total of 467 ports were placed in 465 patients (Men: 206); 10.7% in the accessed group (n=50, age: 60±13.9) and 89.3% in the control group (n=417, age: 59±13.5). There were no statistically significant differences in patient demographics between the groups. The overall complication rate was 0.6% (n=3). Two complications (hematoma causing skin necrosis and thrombosis of the port) occurred in the control group and one (infection) in the accessed group. Infection rates after procedures were 2% (1/50) in the accessed group and 0% (0/417) in the control group. There was no statistically significant difference in overall complication (P=.1) and infection (P=.1) rates among the groups. Leaving the port accessed immediately after placement does not increase the risk of infection or other complications.

19 CFR 4.86 - Intercoastal residue-cargo procedure; optional ports.

Code of Federal Regulations, 2010 CFR

2010-04-01

... agent is unable at that time to designate the specific port or ports of discharge of that residue cargo... ports, Great Lakes coast,” as the case may be. The traveling manifest shall be similarly noted. Upon arrival of the vessel at the first port on the next coast, the master, owner, or agent must designate the...

44 CFR 402.4 - Calls at restricted ports en route to an unrestricted port with restricted cargo.

Code of Federal Regulations, 2012 CFR

2012-10-01

... port or other place in Communist China.) For example, an American flag ship may call at one of the restricted ports (except one in Communist China), even though it has on board the following classes of... for Communist China (the transportation and discharge of which is covered by Order T-2). None of these...

44 CFR 402.4 - Calls at restricted ports en route to an unrestricted port with restricted cargo.

Code of Federal Regulations, 2013 CFR

2013-10-01

... port or other place in Communist China.) For example, an American flag ship may call at one of the restricted ports (except one in Communist China), even though it has on board the following classes of... for Communist China (the transportation and discharge of which is covered by Order T-2). None of these...

44 CFR 402.4 - Calls at restricted ports en route to an unrestricted port with restricted cargo.

Code of Federal Regulations, 2014 CFR

2014-10-01

... port or other place in Communist China.) For example, an American flag ship may call at one of the restricted ports (except one in Communist China), even though it has on board the following classes of... for Communist China (the transportation and discharge of which is covered by Order T-2). None of these...

44 CFR 402.4 - Calls at restricted ports en route to an unrestricted port with restricted cargo.

Code of Federal Regulations, 2010 CFR

2010-10-01

... port or other place in Communist China.) For example, an American flag ship may call at one of the restricted ports (except one in Communist China), even though it has on board the following classes of... for Communist China (the transportation and discharge of which is covered by Order T-2). None of these...

44 CFR 402.4 - Calls at restricted ports en route to an unrestricted port with restricted cargo.

Code of Federal Regulations, 2011 CFR

2011-10-01

... port or other place in Communist China.) For example, an American flag ship may call at one of the restricted ports (except one in Communist China), even though it has on board the following classes of... for Communist China (the transportation and discharge of which is covered by Order T-2). None of these...

Sediment management alternatives for the Biloxi ports.

DOT National Transportation Integrated Search

2010-02-01

The objective of this project is to determine the source of sedimentation in the Ports of Biloxi and provide engineered solutions which will reduce : or eliminate the need for dredging within the ports. : The Commercial Docking Facility, Small Craft ...

Internal Flow Thermal/Fluid Modeling of STS-107 Port Wing in Support of the Columbia Accident Investigation Board

NASA Technical Reports Server (NTRS)

Sharp, John R.; Kittredge, Ken; Schunk, Richard G.

2003-01-01

As part of the aero-thermodynamics team supporting the Columbia Accident Investigation Board (CAB), the Marshall Space Flight Center was asked to perform engineering analyses of internal flows in the port wing. The aero-thermodynamics team was split into internal flow and external flow teams with the support being divided between shorter timeframe engineering methods and more complex computational fluid dynamics. In order to gain a rough order of magnitude type of knowledge of the internal flow in the port wing for various breach locations and sizes (as theorized by the CAB to have caused the Columbia re-entry failure), a bulk venting model was required to input boundary flow rates and pressures to the computational fluid dynamics (CFD) analyses. This paper summarizes the modeling that was done by MSFC in Thermal Desktop. A venting model of the entire Orbiter was constructed in FloCAD based on Rockwell International s flight substantiation analyses and the STS-107 reentry trajectory. Chemical equilibrium air thermodynamic properties were generated for SINDA/FLUINT s fluid property routines from a code provided by Langley Research Center. In parallel, a simplified thermal mathematical model of the port wing, including the Thermal Protection System (TPS), was based on more detailed Shuttle re-entry modeling previously done by the Dryden Flight Research Center. Once the venting model was coupled with the thermal model of the wing structure with chemical equilibrium air properties, various breach scenarios were assessed in support of the aero-thermodynamics team. The construction of the coupled model and results are presented herein.

Port-Wine Stains

MedlinePlus

... or surgery. Port-wine stains can also develop grape-like growths of small blood vessels called vascular ... another part of themselves — like their height or eye color. It's also important, emotionally, for kids to ...

33 CFR 401.65 - Communication-ports, docks and anchorages.

Code of Federal Regulations, 2010 CFR

2010-07-01

... anchorages. 401.65 Section 401.65 Navigation and Navigable Waters SAINT LAWRENCE SEAWAY DEVELOPMENT....65 Communication—ports, docks and anchorages. (a) Every vessel entering or leaving a lake port shall... the harbor entrance. (b) Every vessel arriving at a port, dock or anchorage shall report to the...

33 CFR 401.65 - Communication-ports, docks and anchorages.

Code of Federal Regulations, 2014 CFR

2014-07-01

... anchorages. 401.65 Section 401.65 Navigation and Navigable Waters SAINT LAWRENCE SEAWAY DEVELOPMENT....65 Communication—ports, docks and anchorages. (a) Every vessel entering or leaving a lake port shall... the harbor entrance. (b) Every vessel arriving at a port, dock or anchorage shall report to the...

33 CFR 401.65 - Communication-ports, docks and anchorages.

Code of Federal Regulations, 2011 CFR

2011-07-01

... anchorages. 401.65 Section 401.65 Navigation and Navigable Waters SAINT LAWRENCE SEAWAY DEVELOPMENT....65 Communication—ports, docks and anchorages. (a) Every vessel entering or leaving a lake port shall... the harbor entrance. (b) Every vessel arriving at a port, dock or anchorage shall report to the...

33 CFR 401.65 - Communication-ports, docks and anchorages.

Code of Federal Regulations, 2013 CFR

2013-07-01

... anchorages. 401.65 Section 401.65 Navigation and Navigable Waters SAINT LAWRENCE SEAWAY DEVELOPMENT....65 Communication—ports, docks and anchorages. (a) Every vessel entering or leaving a lake port shall... the harbor entrance. (b) Every vessel arriving at a port, dock or anchorage shall report to the...

33 CFR 401.65 - Communication-ports, docks and anchorages.

Code of Federal Regulations, 2012 CFR

2012-07-01

... anchorages. 401.65 Section 401.65 Navigation and Navigable Waters SAINT LAWRENCE SEAWAY DEVELOPMENT....65 Communication—ports, docks and anchorages. (a) Every vessel entering or leaving a lake port shall... the harbor entrance. (b) Every vessel arriving at a port, dock or anchorage shall report to the...

The construction strategy and measures for ecological analysis of China's ports

NASA Astrophysics Data System (ADS)

Zhang, Lu; Zhao, Junjie; Shou, Youping; Wang, Ning; Qiao, Jianzhe; Tian, Mingjing

2018-04-01

The Port is an important transport hub, one of the important infrastructure of the national economy, the corresponding regional development has a great role in promoting.The construction of the port has been developed rapidly, but it has also brought about more serious environmental problems. Therefore, this paper discusses the nature of ecological ports, summarized the experience of ecological protection measures on the international advanced ports and port construction ecology. The central idea is to explore the construction of ecological port ideas and development countermeasures.

Public Port Finance Survey for FY 1998

DOT National Transportation Integrated Search

1999-12-01

The report is a joint effort of the American Association of Port Authorities and the Maritime Administration, U. S. Dept. of Transportation. It covers financial data on maritime activities at 70 U. S. and Canadian ports, including the income statemen...

Diesel exhaust exposures in port workers.

PubMed

Debia, Maximilien; Neesham-Grenon, Eve; Mudaheranwa, Oliver C; Ragettli, Martina S

2016-07-01

Exposure to diesel engine exhaust has been linked to increased cancer risk and cardiopulmonary diseases. Diesel exhaust is a complex mixture of chemical substances, including a particulate fraction mainly composed of ultrafine particles, resulting from the incomplete combustion of fuel. Diesel trucks are known to be an important source of diesel-related air pollution, and areas with heavy truck traffic are associated with higher air pollution levels and increased public health problems. Several indicators have been proposed as surrogates for estimating exposures to diesel exhaust but very few studies have focused specifically on monitoring the ultrafine fraction through the measurement of particle number concentrations. The aim of this study is to assess occupational exposures of gate controllers at the port of Montreal, Canada, to diesel engine emissions from container trucks by measuring several surrogates through a multimetric approach which includes the assessment of both mass and number concentrations and the use of direct reading devices. A 10-day measurement campaign was carried out at two terminal checkpoints at the port of Montreal. Respirable elemental and organic carbon, PM1, PM2.5, PMresp (PM4), PM10, PMtot (inhalable fraction), particle number concentrations, particle size distributions, and gas concentrations (NO2, NO, CO) were monitored. Gate controllers were exposed to concentrations of contaminants associated with diesel engine exhaust (elemental carbon GM = 1.6 µg/m(3); GSD = 1.6) well below recommended occupational exposure limits. Average daily particle number concentrations ranged from 16,544-67,314 particles/cm³ (GM = 32,710 particles/cm³; GSD = 1.6). Significant Pearson correlation coefficients were found between daily elemental carbon, PM fractions and particle number concentrations, as well as between total carbon, PM fractions and particle number concentrations. Significant correlation coefficients were found between particle number

77 FR 29932 - Safety Zone; Nautical City Festival Air Show, Rogers City, MI

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-21

...-AA00 Safety Zone; Nautical City Festival Air Show, Rogers City, MI AGENCY: Coast Guard, DHS. ACTION... City Festival will be celebrating Calcite's 100th Anniversary. As part of that celebration, an air show will be launched to the east of the Rogers City marina. The Captain of the Port Sault Sainte Marie has...

Device having two optical ports for switching applications

DOEpatents

Rosen, Ayre; Stabile, Paul J.

1991-09-24

A two-sided light-activatable semiconductor switch device having an optical port on each side thereof. The semiconductor device may be a p-i-n diode or of bulk intrinsic material. A two ported p-i-n diode, reverse-biased to "off" by a 1.3 kV dc power supply, conducted 192 A when activated by two 1 kW laser diode arrays, one for each optical port.

Surface sediment quality relative to port activities: A contaminant-spectrum assessment.

PubMed

Yu, Shen; Hong, Bing; Ma, Jun; Chen, Yongshan; Xi, Xiuping; Gao, Jingbo; Hu, Xiuqin; Xu, Xiangrong; Sun, Yuxin

2017-10-15

Ports are facing increasing environmental concerns with their importance to the global economy. Numerous studies indicated sediment quality deterioration in ports; however, the deterioration is not discriminated for each port activity. This study investigated a spectrum of contaminants (metals and organic pollutants) in surface sediments at 20 sampling points in Port Ningbo, China, one of the top five world ports by volume. The spectrum of contaminants (metals and organic pollutants) was quantified following marine sediment quality guidelines of China and USA and surface sediment quality was assessed according to thresholds of the two guidelines. Coupling a categorical matrix of port activities with the matrix of sedimentary contaminants revealed that contaminants were highly associated with the port operations. Ship repair posed a severe chemical risk to sediment. Operations of crude oil and coal loadings were two top activities related to organic pollutants in sediments while port operations of ore and container loadings discharged metals. Among the 20 sampling points, Cu, Zn, Pb, and DDT and its metabolites were the priority contaminants influencing sediment quality. Overall, surface sediments in Port Ningbo had relatively low environmental risks but ship repair is an environmental concern that must be addressed. This study provides a practical approach for port activity-related quality assessment of surface sediments in ports that could be applicable in many world sites. Copyright © 2017 Elsevier B.V. All rights reserved.

Contextual view of ILWU Hall, facing northwest with commercial port ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Contextual view of ILWU Hall, facing northwest with commercial port buildings visible in the background - International Longshoremen's & Warehousemen's Union Hall, Naval Civil Engineering Laboratory, Port Hueneme Road, Port Hueneme, Ventura County, CA

33 CFR 334.1230 - Port Orchard; naval restricted area.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Port Orchard; naval restricted... ARMY, DEPARTMENT OF DEFENSE DANGER ZONE AND RESTRICTED AREA REGULATIONS § 334.1230 Port Orchard; naval restricted area. (a) Port Orchard; naval restricted area—(1) The area. Shoreward of a line beginning at a...

33 CFR 334.1230 - Port Orchard; naval restricted area.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 3 2011-07-01 2011-07-01 false Port Orchard; naval restricted... ARMY, DEPARTMENT OF DEFENSE DANGER ZONE AND RESTRICTED AREA REGULATIONS § 334.1230 Port Orchard; naval restricted area. (a) Port Orchard; naval restricted area—(1) The area. Shoreward of a line beginning at a...

Risk factors for venous port migration in a single institute in Taiwan.

PubMed

Fan, Wen-Chieh; Wu, Cheng-Han; Tsai, Ming-Ju; Tsai, Ying-Ming; Chang, Hsu-Liang; Hung, Jen-Yu; Chen, Pei-Huan; Yang, Chih-Jen

2014-01-14

An implantable port device provides an easily accessible central route for long-term chemotherapy. Venous catheter migration is one of the rare complications of venous port implantation. It can lead to side effects such as pain in the neck, shoulder, or ear, venous thrombosis, and even life-threatening neurologic problems. To date, there are few published studies that discuss such complications. This retrospective study of venous port implantation in a single center, a Taiwan hospital, was conducted from January 2011 to March 2013. Venous port migration was recorded along with demographic and characteristics of the patients. Of 298 patients with an implantable import device, venous port migration had occurred in seven, an incidence rate of 2.3%. All seven were male and had received the Bard port Fr 6.6 which had smaller size than TYCO port Fr 7.5 and is made of silicon. Significantly, migration occurred in male patients (P = 0.0006) and in those with lung cancer (P = 0.004). Multivariable logistic regression analysis revealed that lung cancer was a significant risk factor for port migration (odds ratio: 11.59; P = 0.0059). The migration rate of the Bard port Fr 6.6 was 6.7%. The median time between initial venous port implantation and port migration was 35.4 days (range, 7 to 135 days) and 71.4% (5/7) of patients had port migration within 30 days after initial port implantation. Male sex and lung cancer are risk factors for venous port migration. The type of venous port is also an important risk factor.