Science.gov

Sample records for arancelarias al comercio

  1. ALS - resources

    MedlinePlus

    Resources - ALS ... The following organizations are good resources for information on amyotrophic lateral sclerosis : Muscular Dystrophy Association -- mda.org/disease/amyotrophic-lateral-sclerosis National Amyotrophic Lateral Sclerosis (ALS) Registry -- ...

  2. ALS Association

    MedlinePlus

    ... ALS. Find Out How Our Mission Leading the fight to treat and cure ALS through global research ... you participate, advocate, and donate, you advance the fight to find the cure and lead us toward ...

  3. Al Composites

    NASA Astrophysics Data System (ADS)

    Chandanayaka, Tharaka; Azarmi, Fardad

    2014-05-01

    In the present study, cold spraying technique was used to fabricate a metal matrix composite (MMC) that consists of Ni matrix and 20 vol.% Ni3Al particles at two different particle sizes as reinforcement. This study intends to investigate the effect of reinforcement particle size on microstructural and mechanical properties of cold sprayed MMCs. Two different Ni3Al powders with nominal particle size of -45 to +5 and +45 to 100 μm were used as reinforcement in this study. Cold sprayed Ni-Ni3Al samples were subjected to the microstructural observation and characterization prior to any mechanical testing. Then, samples were tested using nano-indentation, Knoop hardness, Vickers hardness, and Resonance frequency to evaluate their mechanical properties. No significant changes were observed in microstructural characteristics due to different particle sizes. The results obtained from a variety of mechanical testings indicated that the increasing reinforcement particle size resulted in the slight reduction of mechanical properties such as elastic modulus and hardness in cold sprayed MMCs. The mechanical interlock between deposited particles defines the bonding strength in cold sprayed samples. Small size particles have a higher velocity and impact resulting in stronger interlock between deformed particles.

  4. AL Amyloidosis

    PubMed Central

    2012-01-01

    Definition of the disease AL amyloidosis results from extra-cellular deposition of fibril-forming monoclonal immunoglobulin (Ig) light chains (LC) (most commonly of lambda isotype) usually secreted by a small plasma cell clone. Most patients have evidence of isolated monoclonal gammopathy or smoldering myeloma, and the occurrence of AL amyloidosis in patients with symptomatic multiple myeloma or other B-cell lymphoproliferative disorders is unusual. The key event in the development of AL amyloidosis is the change in the secondary or tertiary structure of an abnormal monoclonal LC, which results in instable conformation. This conformational change is responsible for abnormal folding of the LC, rich in β leaves, which assemble into monomers that stack together to form amyloid fibrils. Epidemiology AL amyloidosis is the most common type of systemic amyloidois in developed countries with an estimated incidence of 9 cases/million inhabitant/year. The average age of diagnosed patients is 65 years and less than 10% of patients are under 50. Clinical description The clinical presentation is protean, because of the wide number of tissues or organs that may be affected. The most common presenting symptoms are asthenia and dyspnoea, which are poorly specific and may account for delayed diagnosis. Renal manifestations are the most frequent, affecting two thirds of patients at presentation. They are characterized by heavy proteinuria, with nephrotic syndrome and impaired renal function in half of the patients. Heart involvement, which is present at diagnosis in more than 50% of patients, leading to restrictive cardiopathy, is the most serious complication and engages prognosis. Diagnostic methods The diagnosis relies on pathological examination of an involved site showing Congo red-positive amyloid deposits, with typical apple-green birefringence under polarized light, that stain positive with an anti-LC antibody by immunohistochemistry and/or immunofluorescence. Due to the

  5. ALS - The cost cutter

    NASA Astrophysics Data System (ADS)

    Colucci, Frank

    1987-10-01

    The Advanced Launch System (ALS) development program will avail itself of existing technologies in the short term in order to produce an interim 'core' vehicle that may be operational by 1993; the full, booster-incorporating system objective will then be achieved in 1998. This programmatic 'decoupling' of booster and core vehicle development efforts will separate their funding peaks. The ALS program will cut costs by colocating manufacturing and launch facilities, using Al-Li alloys in booster primary structures, and aggressively applying 'paperless' CIM. The ALS launch vehicle configuration will be primarily determined by both payload requirements and flight frequency.

  6. Al-Anon/Alateen

    MedlinePlus

    Find an Al-Anon meeting Español | Français 2018 Int'l Convention Home About Group Meetings What If I'm not ready ... a meeting? What can I expect at an Al-Anon meeting? What was my first meeting like? ...

  7. [Environmental factors in ALS].

    PubMed

    Juntas-Morales, Raul; Pageot, Nicolas; Corcia, Philippe; Camu, William

    2014-05-01

    ALS is likely to be a disorder of multifactorial origin. Among all the factors that may increase the risk of ALS, environmental ones are being studied for many years, but in the recent years, several advances have pointed to a new interest in their potential involvement in the disease process, especially for the cyanotoxin BMAA. Food containing BMAA has been found on Guam, a well-known focus of ALS/parkinsonism/dementia and high levels of BMAA have been identified into the brain of these patients. The BMAA cyanotoxin is potentially ubiquitous and have also been found into the food of patients who died from ALS both in Europe and USA. BMAA can be wrongly integrated into the protein structure during mRNA traduction, competing with serine. This may induce abnormal protein folding and a subsequent cell death. Heavy metals, such as lead or mercury may be directly toxic for neuronal cells. Several works have suggested an increased risk of ALS in individuals chronically exposed to these metals. Exposure to pesticides has been suggested to be linked to an increased risk of developing ALS. The mechanism of their toxicity is likely to be mediated by paraoxonases. These proteins are in charge of detoxifying the organism from toxins, and particularly organophosphates. To date, there are insufficient scientific data to suggest that exposure to electromagnetic fields may increase the risk of having ALS. We are particularly missing longitudinal cohorts to demonstrate that risk. PMID:24703731

  8. Genetic Testing for ALS

    MedlinePlus

    ... Involved Donate Familial Amyotrophic Lateral Sclerosis (FALS) and Genetic Testing By Deborah Hartzfeld, MS, CGC, Certified Genetic ... guarantee a person will develop symptoms of ALS. Genetic Counseling If there is more than one person ...

  9. All About ALS

    MedlinePlus

    ... External link, please review our exit disclaimer . Subscribe All About ALS Understanding a Devastating Disorder In the ... a coffee pot, or button a shirt. Eventually, all muscles under voluntary control are affected, and people ...

  10. Amyotrophic Lateral Sclerosis (ALS)

    MedlinePlus

    ... Pictures of ALS Mutant Proteins Support Two Major Theories About How the Disease is Caused May 2003 ... All NINDS-prepared information is in the public domain and may be freely copied. Credit to the ...

  11. What Is ALS?

    MedlinePlus

    ... scarring or hardening ("sclerosis") in the region. Motor neurons reach from the brain to the spinal cord ... the body. The progressive degeneration of the motor neurons in ALS eventually leads to their demise. When ...

  12. ALS synchrotron radiation shielding

    SciTech Connect

    Donahue, R.J.

    1995-10-01

    This note discusses the assumptions and results of synchrotron radiation shielding estimates for ALS bend magnet and wiggler beamlines. Estimates of gas bremsstrahlung production are not included and are dealt with elsewhere.

  13. Rapidly solidified NiAl and FeAl

    NASA Technical Reports Server (NTRS)

    Gaydosh, D. J.; Crimp, M. A.

    1984-01-01

    Melt spinning was used to produce rapidly solidified ribbons of the B2 intermetallics NiAl and FeAl. Both Fe-40Al and Fe-45Al possessed some bend ductility in the as spun condition. The bend ductility of Fe-40Al, Fe-45Al, and equiatomic NiAl increased with subsequent heat treatment. Heat treatment at approximately 0.85 T (sub m) resulted in significant grain growth in equiatomic FeAl and in all the NiAl compositions. Low bend ductility in both FeAl and NiAl generally coincided with intergranular failure, while increased bend ductility was characterized by increasing amounts of transgranular cleavage fracture.

  14. Modulus measurements in ordered Co-Al, Fe-Al, and Ni-Al alloys

    NASA Technical Reports Server (NTRS)

    Harmouche, M. R.; Wolfenden, A.

    1985-01-01

    The composition and/or temperature dependence of the dynamic Young's modulus for the ordered B2 Co-Al, Fe-Al, and Ni-Al aluminides has been investigated using the piezoelectric ultrasonic composite oscillator technique (PUCOT). The modulus has been measured in the composition interval 48.49 to 52.58 at. pct Co, 50.87 to 60.2 at. pct Fe, and 49.22 to 55.95 at. pct Ni for Co-Al, Fe-Al, and Ni-Al, respectively. The measured values for Co-Al are in the temperature interval 300 to 1300 K, while those for the other systems are for ambient temperature only. The data points show that Co-Al is stiffer than Fe-Al, which is stiffer than Ni-Al. The data points for Fe-Al and Ni-Al are slightly higher than those reported in the literature.

  15. ALS renewal moves forward

    NASA Astrophysics Data System (ADS)

    Falcone, R. W.; Feinberg, B.; Hussain, Z.; Kirz, J.; Krebs, G. F.; Padmore, H. A.; Robin, D. S.; Robinson, A. L.

    2007-11-01

    As the result of an extensive long-term planning process involving all its stakeholders—management, staff, and users—the ALS has seen its future and is aggressively moving ahead to implement its vision for keeping the facility at the cutting edge for the next 2-3 decades. The evolving strategic plan now in place aims to renew the ALS so it can address a new generation of fundamental questions about size dependent and dimensional-confinement phenomena at the nanoscale; correlation and complexity in physical, biological, and environmental systems; and temporal evolution, assembly, dynamics and ultrafast phenomena. The renewal spans three areas: (1) increased staffing at beamlines to support the growing user community and safety professionals to keep an increasingly complex facility hazard free; (2) implementing advances in accelerator, insertion device, beamline, and detector technology that will make it possible for ALS users to address emerging grand scientific and technological challenges with incisive world-class tools; and (3) construction of a user support building and guest housing that will increase the safety and user friendliness of the ALS by providing users office, meeting, experiment staging, and laboratory space for their work and on-site accommodations at reasonable rates.

  16. Fosetyl-al

    Integrated Risk Information System (IRIS)

    Fosetyl - al ; CASRN 39148 - 24 - 8 Human health assessment information on a chemical substance is included in the IRIS database only after a comprehensive review of toxicity data , as outlined in the IRIS assessment development process . Sections I ( Health Hazard Assessments for Noncarcinogenic Ef

  17. Al Shanker Remembers.

    ERIC Educational Resources Information Center

    American Educator, 2000

    2000-01-01

    In a 1996 interview shortly before his death, Al Shanker, longtime president of the American Federation of Teachers, discussed such topics as: his own educational experiences; how he learned about political fighting in the Boy Scouts; the appeal of socialism; multinational corporations and the nation state; teaching tough students; and John Dewey…

  18. ALS Project Management Manual

    SciTech Connect

    Krupnick, Jim; Harkins, Joe

    2000-05-01

    This manual has been prepared to help establish a consistent baseline of management practices across all ALS projects. It describes the initial process of planning a project, with a specific focus on the production of a formal project plan. We feel that the primary weakness in ALS project management efforts to date stems from a failure to appreciate the importance of ''up-front'' project planning. In this document, we present a guide (with examples) to preparing the documents necessary to properly plan, monitor, and control a project's activities. While following the manual will certainly not guarantee good project management, failure to address the issues we raise will dramatically reduce the chance of success. Here we define success as meeting the technical goals on schedule and within the prescribed budget.

  19. ALS insertion devices

    SciTech Connect

    Hoyer, E.; Chin, J.; Halbach, K.; Hassenzahl, W.V.; Humphries, D.; Kincaid, B.; Lancaster, H.; Plate, D.

    1990-11-01

    The Advanced Light Source (ALS), the first US third generation synchrotron radiation source, is currently under construction at the Lawrence Berkeley Laboratory. The low-emittance, 1.5 GeV electron storage ring and the insertion devices are specifically designed to produce high brightness beams in the UV to soft X-Ray range. The planned initial complement of insertion devices includes four 4.6 m long undulators, with period lengths of 3.9 cm, 5.0 cm (2) and 8.0 cm, and a 2.9 m long wiggler of 16 cm period length. Undulator design is well advanced and fabrication has begun on the 5.0 cm and 8.0 cm period length undulators. This paper discusses ALS insertion device requirements; general design philosophy; and design of the magnetic structure, support structure/drive systems, control system and vacuum system. 18 refs., 9 figs., 5 tabs.

  20. Ausbildung als zentrale Aufgabe

    NASA Astrophysics Data System (ADS)

    Krämer, Walter; Schmerbach, Sibylle

    Anders als Lesen und Schreiben zählen Grundkenntnisse in Statistik heute noch nicht zu den Voraussetzungen einer sinnvollen Teilhabe am Sozialgeschehen. Und auch in der akademischen Statistik-Ausbildung gibt es noch einiges zu tun. Das vorliegende Kapitel zeichnet die Geschichte dieser akademischen Ausbildung an deutschen Universitäten nach dem zweiten Weltkrieg nach, stellt aktuelle Defizite vor und weist auf mögliche Verbesserungen hin.

  1. Optical gain characteristics in Al-rich AlGaN/AlN quantum wells

    SciTech Connect

    Oto, Takao; Banal, Ryan G.; Funato, Mitsuru; Kawakami, Yoichi

    2014-05-05

    The optical gain characteristics of Al-rich AlGaN/AlN quantum wells (QWs) were assessed by the variable stripe length method at room temperature. An Al{sub 0.79}Ga{sub 0.21}N/AlN QW with a well width of 5 nm had a large optical gain of 140 cm{sup −1}. Increasing the excitation length induced a redshift due to the gain consumption and the consequent saturation of the amplified spontaneous emission. Moreover, a change in the dominant gain polarization with Al composition, which was attributed to switching of the valence band ordering of strained AlGaN/AlN QWs at Al compositions of ∼0.8, was experimentally demonstrated.

  2. AL Amyloidosis and Agent Orange

    MedlinePlus

    ... for survivors' benefits . Research on AL amyloidosis and herbicides The Health and Medicine Division (formally known as ... to the compounds of interest found in the herbicide Agent Orange and AL amyloidosis." VA made a ...

  3. Al(+)-ligand binding energies

    NASA Technical Reports Server (NTRS)

    Sodupe, M.; Bauschlicher, Charles W., Jr.

    1991-01-01

    Ab initio calculations are used to optimize the structure and determine the binding energies of Al(+) to a series of ligands. For Al(+)-CN, the bonding was found to have a large covalent component. For the remaining ligands, the bonding is shown to be electrostatic in origin. The results obtained for Al(+) are compared with those previously reported for Mg(+).

  4. Al Jazirah, Sudan

    NASA Technical Reports Server (NTRS)

    2008-01-01

    Al Jazirah (also Gezira) is one of the 26 states of Sudan. The state lies between the Blue Nile and the White Nile in the east-central region of the country. It is a well populated area suitable for agriculture. The area was at the southern end of Nubia and little is known about its ancient history and only limited archaeological work has been conducted in this area. The region has benefited from the Gezira Scheme, a program to foster cotton farming begun in 1925. At that time the Sennar Dam and numerous irrigation canals were built. Al Jazirah became the Sudan's major agricultural region with more than 2.5 million acres (10,000 km) under cultivation. The initial development project was semi-private, but the government nationalized it in 1950. Cotton production increased in the 1970s but by the 1990s increased wheat production has supplanted a third of the land formerly seeded with cotton.

    The image was acquired December 25, 2006, covers an area of 56 x 36.4 km, and is located near 14.5 degrees north latitude, 33.1 degrees east longitude.

    The U.S. science team is located at NASA's Jet Propulsion Laboratory, Pasadena, Calif. The Terra mission is part of NASA's Science Mission Directorate.

  5. Studies of 27Al NMR in EuAl4

    NASA Astrophysics Data System (ADS)

    Niki, H.; Nakamura, S.; Higa, N.; Kuroshima, H.; Toji, T.; Yogi, M.; Nakamura, A.; Hedo, M.; Nakama, T.; Ōnuki, Y.; Harima, H.

    2015-03-01

    EuAl4 orders antiferromagnetically at TN ≈ 16 K with an effective magnetic moment of 8.02 μB. In the paramagnetic phase, the magnetic susceptibility of EuAl4 follows the Curie-Weiss law with a positive Curie-Weiss temperature θP = +14 K. The antiferromagnetic state is changed into the field induced ferromagnetic state at a critical field Hc of approximately 2 T. In order to microscopically investigate the magnetic and electronic properties in EuAl4, the NMR measurements of EuAl4 have been carried out at temperatures between 2 and 300 K, applying an external magnetic field of approximately 6.5 T. The 27Al NMR spectra corresponding to Al(I) and Al(II) sites are obtained. From the 27Al NMR spectra, the isotropic part Kiso and anisotropic part Kaniso of Knight shift, and nuclear quadrupole frequncy νQ are obtained. The Kiso and Kaniso shift to negative side with decreasing temperature due to the RKKY interaction. These temperature dependences follow the Curie-Weiss law with θP = +14 K, which is consistent with that of the magnetic susceptibility. From the K - χ plot, the values of the hyperfine fields Hhf_iso and Hhf_aniso are -3.231 and -0.162 kOe/μB for Al(I) site, and -1.823 and -0.264 kOe/μB for Al(II) site, respectively. The values of νQ of 27Al nucleus for Al(I) and Al(II) sites are approximately 0.865 and 0.409 MHz, respectively. The nuclear relaxation time T1 of 27Al NMR for both sites is almost constant in the paramagnetic phase, while the value of 1/T1 is abruptly decreased in the ordered ferromagnetic state.

  6. Interfacial characterization of Al-Al thermocompression bonds

    NASA Astrophysics Data System (ADS)

    Malik, N.; Carvalho, P. A.; Poppe, E.; Finstad, T. G.

    2016-05-01

    Interfaces formed by Al-Al thermocompression bonding were studied by the transmission electron microscopy. Si wafer pairs having patterned bonding frames were bonded using Al films deposited on Si or SiO2 as intermediate bonding media. A bond force of 36 or 60 kN at bonding temperatures ranging from 400-550 °C was applied for a duration of 60 min. Differences in the bonded interfaces of 200 μm wide sealing frames were investigated. It was observed that the interface had voids for bonding with 36 kN at 400 °C for Al deposited both on Si and on SiO2. However, the dicing yield was 33% for Al on Si and 98% for Al on SiO2, attesting for the higher quality of the latter bonds. Both a bond force of 60 kN applied at 400 °C and a bond force of 36 kN applied at 550 °C resulted in completely bonded frames with dicing yields of, respectively, 100% and 96%. A high density of long dislocations in the Al grains was observed for the 60 kN case, while the higher temperature resulted in grain boundary rotation away from the original Al-Al interface towards more stable configurations. Possible bonding mechanisms and reasons for the large difference in bonding quality of the Al films deposited on Si or SiO2 are discussed.

  7. Studies of 27Al NMR in SrAl4

    NASA Astrophysics Data System (ADS)

    Niki, Haruo; Higa, Nonoka; Kuroshima, Hiroko; Toji, Tatsuki; Morishima, Mach; Minei, Motofumi; Yogi, Mamoru; Nakamura, Ai; Hedo, Masato; Nakama, Takao; Ōnuki, Yoshichika; Harima, Hisatomo

    A charge density wave (CDW) transition at TCDW = 243 K and a structural phase (SP) transition at approximately 100 K occur in SrAl4 with the BaAl4-type body center tetragonal structure, which is the divalent and non-4f electron reference compound of EuAl4. To understand the behaviors of the CDW and SP transitions, the 27Al NMR measurements using a single crystal and a powder sample of SrAl4 have been carried out. The line width below TCDW is modulated by an electrical quadruple interaction between 27Al nucleus and CDW charge modulation. The incommensurate CDW state below TCDW changes into a different structure below TSP. The temperature dependences of Knight shifts of 27Al(I) and 27Al(II) show the different behaviors. The temperature variation of 27Al(I) Knight shift shows anomalies at the CDW and SP transition temperatures, revealing the shift to negative side below TCDW, which is attributable to the core polarization of the d-electrons. However, 27Al(II) Knight shift keeps almost constant except for the small shift due to the SP transition. The 1/T1T of 27Al(I) indicates the obvious changes due to the CDW and SP transitions, while that of 27Al(II) takes a constant value. The density of state at the Fermi level at Al(I) site below 60 K would be about 0.9 times less than that above TCDW.

  8. ALS Performance Summary - Update

    SciTech Connect

    Waters, A M; Brown, W D; Martz, Jr., H E

    2004-09-30

    High Energy Density Physics (HEDP) experiments play an important role in corroborating the improved physics codes that underlie LLNL's Stockpile Stewardship mission. Conducting these experiments, whether on the National Ignition Facility (NIF) or another national facility such as Omega, will require not only improvement in the diagnostics for measuring the experiment, but also detailed knowledge of the as-built target components and assemblies themselves. To assist in this effort, a defined set of well-known reference standards designed to represent a range of HEDP targets have been built and are being used to quantify the performance of different characterization techniques [Hibbard, et al. 2004]. Without the critical step of using reference standards for qualifying characterization tools there can be no verification of either commercial or internally-developed characterization techniques and thus an uncertainty in the input to the physics code models would exist.

  9. Doppelthydrophile Blockcopolymere als Mineralisationstemplate

    NASA Astrophysics Data System (ADS)

    Kasparova, Pavla

    2002-07-01

    Die vorliegende Arbeit beschäftigt sich mit der Synthese und den Eigenschaften von doppelthydrophilen Blockcopolymeren und ihrer Anwendung in einem biomimetischen Mineralisationsprozeß von Calciumcarbonat und Bariumsulfat. Doppelthydrophile Blockcopolymere bestehen aus einem hydrophilen Block, der nicht mit Mineralien wechselwirkt und einem zweiten Polyelektrolyt-Block, der stark mit Mineraloberflächen wechselwirkt. Diese Blockcopolymere wurden durch ringöffnende Polymerisation von N-carboxyanhydriden (NCA's) und a-methoxy-ω-amino[poly(ethylene glycol)] PEG-NH2 als Initiator hergestellt. Die hergestellten Blockcopolymere wurden als effektive Wachstumsmodifikatoren für die Kristallisation von Calciumcarbonat und Bariumsulfat Mineralien eingesetzt. Die so erhaltenen Mineralpartikel (Kugeln, Hantel, eiförmige Partikel) wurden durch Lichtmikroskopie in Lösung, SEM und TEM charakterisiert. Röntgenweitwinkelstreuung (WAXS) wurde verwendet, um die Modifikation von Calciumcarbonat zu ermitteln und die Größe der Calciumcarbonat- und Bariumsulfat-Nanopartikel zu ermitteln. This work describes the synthesis and characterization of double hydrophilic block copolymers and their use in a biomimetic mineralization process of Calcium Carbonate and Barium Sulfate. Double hydrophilic block copolymers consist of a hydrophilic block that does not interact with minerals and another hydrophilic polyelectrolyte block that strongly interacts with mineral surfaces. These polymers were synthesised via ring opening polymerisation of N-carboxyanhydride (NCA), and the first hydrophilic block a-methoxy-ω-amino[poly(ethylene glycol)] PEG-NH2 was used as an initiator. The prepared block copolymers were used as effective crystal growth modifiers to control the crystallization of Calcium Carbonate and Barium Sulfate minerals. The resulting mineral particles (spheres, dumbbells, egg-like particles) were characterised by light microscopy in solution, by SEM, and by TEM. X-Ray scattering

  10. Interfacial reactions and oxidation behavior of Al 2O 3 and Al 2O 3/Al coatings on an orthorhombic Ti 2AlNb alloy

    NASA Astrophysics Data System (ADS)

    Li, H. Q.; Wang, Q. M.; Gong, J.; Sun, C.

    2011-02-01

    The uniform and dense Al2O3 and Al2O3/Al coatings were deposited on an orthorhombic Ti2AlNb alloy by filtered arc ion plating. The interfacial reactions of the Al2O3/Ti2AlNb and Al2O3/Al/Ti2AlNb specimens after vacuum annealing at 750 °C were studied. In the Al2O3/Ti2AlNb specimens, the Al2O3 coating decomposed significantly due to reaction between the Al2O3 coating and the O-Ti2AlNb substrate. In the Al2O3/Al/Ti2AlNb specimens, a γ-TiAl layer and an Nb-rich zone came into being by interdiffusion between the Al layer and the O-Ti2AlNb substrate. The γ-TiAl layer is chemically compatible with Al2O3, with no decomposition of Al2O3 being detected. No internal oxidation or oxygen and nitrogen dissolution zone was observed in the O-Ti2AlNb alloy. The Al2O3/Al/Ti2AlNb specimens exhibited excellent oxidation resistance at 750 °C.

  11. Rub' al Khali, Arabia

    NASA Technical Reports Server (NTRS)

    2008-01-01

    The Rub' al Khali is one of the largest sand deserts in the world, encompassing most of the southern third of the Arabian Peninsula. It includes parts of Oman, United Arab Emirates, and Yemen. The desert covers 650,000 square kilometers, more than the area of France. Largely unexplored until recently, the desert is 1000 km long and 500 km wide. The first documented journeys made by Westerners were those of Bertram Thomas in 1931 and St. John Philby in 1932. With daytime temperatures reaching 55 degrees Celsius, and dunes taller than 330 meters, the desert may be one of the most forbidding places on Earth.

    The image was acquired December 2, 2005, covers an area of 54.8 x 61.9 km, and is located near 20.7 degrees north latitude, 53.6 degrees east longitude.

    The U.S. science team is located at NASA's Jet Propulsion Laboratory, Pasadena, Calif. The Terra mission is part of NASA's Science Mission Directorate.

  12. Alexandria (Al Iskandariya), Egypt

    NASA Technical Reports Server (NTRS)

    2002-01-01

    This image of Alexandria was taken by astronauts on board the International Space Station in December 2000 using an Electronic Still Camera. A wider-angle view (STS088-739-90) taken from the Space Shuttle in December 1998 is available for context. Alexandria (Al Iskandariya) occupies a T-shaped peninsula and strip of land separating the Mediterranean from Lake Mariout. Originally the town was built upon a mole (stone breakwater) called Heptastadium, which joined the island of Pharos (see referenced website, below) to the mainland. Since then sedimentary deposits have widened the mole. Since 1905, when the 370,000 Alexandrians lived in an area of about 4 sq km between the two harbors, the city (population 4 million; see referenced website, below) has grown beyond its medieval walls and now occupies an area of about 300 sq km. The Mahmudiya Canal, connecting Alexandria with the Nile, runs to the south of the city and, by a series of locks, enters the harbor of the principal port of Egypt (note ships). The reddish and ochre polygons west of Lake Mariout are salt-evaporation, chemical-storage, and water-treatment ponds within the coastal lagoon. Reference Youssef Halim and Fatma Abou Shouk, 2000, Human impacts on Alexandria's marine environment: UNESCO, Coastal Regions and Small Islands Unit (CSI), Coastal Management Sourcebooks 2 (accessed December 20, 2000) Additional photographs taken by astronauts can be viewed at NASA-JSC's Gateway to Astronaut Photography of Earth. Image ISS001-ESC-5025 provided by the Earth Sciences and Image Analysis Laboratory, Johnson Space Center.

  13. Undulators at the ALS

    SciTech Connect

    Hoyer, E.; Akre, J.; Chin, J.

    1994-07-01

    At Lawrence Berkeley Laboratory`s (LBL) Advanced Light Source (ALS), three 4.6 m long undulators have been completed, tested and installed. A fourth is under construction. The completed undulators include two 5.0 cm period length, 89 period devices (U5.0s) which achieve a 0.85 T effective field at a 14 mm minimum gap and a 8.0 cm period length, 55 period device (U8.0) that reaches a 1.2 T effective field at a 14 mm minimum gap. The undulator under construction is a 10.0 cm period length, 43 period device (U10.0) that is designed to achieve 0.98 T at a 23 mm gap. Undulator magnetic gap variation (rms) is within 25 microns over the periodic structure length. Reproducibility of the adjustable magnetic gap has been measured to be within +/{minus} 5 microns. Gap adjusting range is from 14 mm to 210 mm, which can be scanned in one minute. The 5.1 m long vacuum chambers are flat in the vertical direction to within 0.74 mm and straight in the horizontal direction to within 0.08 mm over the 4.6 m magnetic structure sections. Vacuum chamber base pressures after UHV beam conditioning are. in the mid 10{sup {minus}11} Torr range and storage ring operating pressures with full current are in the low 10{sup {minus}10} Torr range. Measurements show that the uncorrelated magnetic field errors are 0.23%, and 0.20% for the two U5.Os and the U8.0 respectively and that the field integrals are small over the 1 cm by 6 cm beam aperture. Device description, fabrication, and measurements are presented.

  14. Thermal Modeling of Al-Al and Al-Steel Friction Stir Spot Welding

    NASA Astrophysics Data System (ADS)

    Jedrasiak, P.; Shercliff, H. R.; Reilly, A.; McShane, G. J.; Chen, Y. C.; Wang, L.; Robson, J.; Prangnell, P.

    2016-07-01

    This paper presents a finite element thermal model for similar and dissimilar alloy friction stir spot welding (FSSW). The model is calibrated and validated using instrumented lap joints in Al-Al and Al-Fe automotive sheet alloys. The model successfully predicts the thermal histories for a range of process conditions. The resulting temperature histories are used to predict the growth of intermetallic phases at the interface in Al-Fe welds. Temperature predictions were used to study the evolution of hardness of a precipitation-hardened aluminum alloy during post-weld aging after FSSW.

  15. Philosophieren als Unterrichtsprinzip im Mathematikunterricht

    NASA Astrophysics Data System (ADS)

    Meerwaldt, Diana

    Philosophieren und Mathematik scheinen zunächst gegensätzliche Bereiche zu sein, die sich kaum vereinbaren lassen. Dies trifft für eine Auffassung zu, die Philosophieren als "Gerede" disqualifiziert und Mathematik als eine reine "Formelwissenschaft" begreift. Beide Auffassungen werden den Gegenständen nicht gerecht.

  16. Modeling neuronal vulnerability in ALS.

    PubMed

    Roselli, Francesco; Caroni, Pico

    2014-08-20

    Using computational models of motor neuron ion fluxes, firing properties, and energy requirements, Le Masson et al. (2014) reveal how local imbalances in energy homeostasis may self-amplify and contribute to neurodegeneration in ALS. PMID:25144872

  17. Characteristics of CeCoIn5/Al/AlOx/Nb and CeCoIn5/Al/AlOx/Al Tunnel Junctions

    SciTech Connect

    Petrovic, C.; Nevirkovets, I.P.; Chernyashevskyy, O.; Hu, R.; Ketterson, J.B.; Sarma, B.K.

    2009-03-03

    We report characteristics of CeCoIn{sub 5}/Al/AlO{sub x}/Nb and CeCoIn{sub 5}/Al/AlO{sub x}/Al tunnel junctions fabricated on the (0 0 1) surface of CeCoIn{sub 5} crystal platelets. The main result of this work is the observation of a low Josephson current (as compared with that expected from the Ambegaokar-Baratoff formula), which is consistent with idea that the order parameter in the heavy-fermion superconductor CeCoIn{sub 5} has unconventional pairing symmetry.

  18. Stimulated emission in AlGaN/AlGaN quantum wells with different Al content

    NASA Astrophysics Data System (ADS)

    Mickevičius, J.; Jurkevičius, J.; Kazlauskas, K.; Žukauskas, A.; Tamulaitis, G.; Shur, M. S.; Shatalov, M.; Yang, J.; Gaska, R.

    2012-02-01

    Stimulated emission (SE) is studied in AlGaN/AlGaN multiple quantum wells (MQWs) with different Al content grown on sapphire substrate. The spectra of spontaneous and stimulated emission and their transformations with increasing temperature as well as stimulated emission thresholds were measured in the temperature range from 8 to 300 K. Phonon-assisted band broadening in low-Al-content MQWs and double-scaled potential profile in high-Al-content MQWs were observed in the samples and linked with carrier localization conditions. The temperature dependence of the stimulated emission threshold was similar in the samples where the stimulated transitions occur between extended states and in the samples where the transitions occur in localized states. The stimulated emission threshold depends predominantly on the density of nonradiative recombination centers.

  19. Medical application of 26Al

    NASA Astrophysics Data System (ADS)

    Steinhausen, C.; Gerisch, P.; Heisinger, B.; Hohl, Ch.; Kislinger, G.; Korschinek, G.; Niedermayer, M.; Nolte, E.; Dumitru, M.; Alvarez-Brückmann, M.; Schneider, M.; Ittel, T. H.

    1996-06-01

    Accelerator mass spectrometry (AMS) measurements with 26Al as tracer were performed in order to study the aluminium metabolism and anomalies in the human body and in rats. In particular, the differences between healthy volunteers and patients with renal failure were investigated. The obtained data points of 26Al in blood and urine were described by an open compartment model with three peripheral compartments. It was found that the minimum of peripheral compartments needed to describe 26Al concentrations in blood and urine over a time period of three years is at least three.

  20. Reply to Gopalswamy et al.

    NASA Technical Reports Server (NTRS)

    Cane, H. V.; Richardson, I. G.

    2003-01-01

    The comment of Gopalswamy et al. (thereafter GMY) relates to a letter discussing coronal mass ejections (CMEs), interplanetary ejecta and geomagnetic storms. GMY contend that Cane et al. incorrectly identified ejecta (interplanetary CMEs) and hypothesize that this is because Cane et al. fail to understand how to separate ejecta from "shock sheaths" when interpreting solar wind and energetic particle data sets. They (GMY) are wrong be cause the relevant section of the paper was concerned with the propagation time to 1 AU of any potentially geoeffective structures caused by CMEs, i.e. upstream compression regions with or without shocks, or ejecta. In other words, the travel times used by Cane et al. were purposefully and deliberately distinct from ejecta travel times (except for those slow ejecta, approx. 30% of their events, which generated no upstream features), and no error in identification was involved. The confusion of GMY stems from the description did not characterize the observations sufficiently clearly.

  1. In memory of Al Cameron

    NASA Astrophysics Data System (ADS)

    Cowan, John; Truran, James W.

    Al Cameron, who died recently (October 3, 2005) at 80, was one of the giants in astrophysics. His insights were profound and his interests were wide-ranging. Originally trained as a nuclear physicist, he made major contributions in a number of fields, including nuclear reactions in stars, nucleosynthesis, the abundances of the elements in the Solar System, and the origin of the Solar System and the Moon. In 1957, Cameron and, independently, Burbidge, Burbidge, Fowler and Hoyle, wrote seminal papers on nuclear astrophysics. Most of our current ideas concerning ele- ment formation in stars have followed from those two pioneering and historical works. Al also made many contributions in the field of Solar System physics. Particularly noteworthy in this regard was Cameron's work on the formation of the Moon. Al was also a good friend and mentor of young people. Al Cameron will be missed by many in the community both for his scientific contributions and for his friendship.

  2. Comparing the Thermodynamic Behaviour of Al(1)+ZrO2(s) to Al(1)+Al2O3(s)

    NASA Technical Reports Server (NTRS)

    Copland, Evan

    2004-01-01

    In an effort to better determine the thermodynamic properties of Al(g) and Al2O(g). the vapor in equilibrium with Al(l)+ZrO2(s) was compared to the vapor in equilibrium with Al(l)+Al2O3(s) over temperature range 1197-to-1509K. The comparison was made directly by Knudsen effusion-cell mass spectrometry with an instrument configured for a multiple effusion-cell vapor source (multi-cell KEMS). Second law enthalpies of vaporization of Al(g) and Al2O(g) together with activity measurements show that Al(l)+ZrO2(s) is thermodynamically equivalent to Al(l)+Al2O3(s), indicating Al(l) remained pure and Al2O3(s) was present in the ZrO2-cell. Subsequent observation of the Al(l)/ZrO2 and vapor/ZrO2 interfaces revealed a thin Al2O3-layer had formed, separating the ZrO2-cell from Al(l) and Al(g)+Al2O(g), effectively transforming it into an Al2O3 effusion-cell. This behavior agrees with recent observations made for Beta-NiAl(Pt) alloys measured in ZrO2 effusion-cell.

  3. Corrosion Behavior of Al-Al3Ni and Al-Al2Cu Functionally Graded Materials Fabricated by a Centrifugal Method

    NASA Astrophysics Data System (ADS)

    Noda, Kazuhiko; Miyahara, Keita; Watanabe, Yoshimi

    2008-02-01

    Intermetallic compounds, such as Al3Ni and Al2Cu, are effective for enhancing the mechanical properties of an alloy. Al-Al3Ni and Al-Al2Cu functionally graded materials (FGMs) might be attractive materials for advanced materials. Al-Al3Ni and Al-Al2Cu FGMs were fabricated by a centrifugal method; the centrifugal method is an extremely effective method for fabricating FGMs. Al-Al3Ni and Al-Al2Cu FGMs that had a graded distribution of intermetallic compounds could be produced by this in-situ centrifugal method. Particle size, particle shape and the distribution of intermetallic compounds were controlled by varying the content of the alloy element (Ni, Cu) in the master alloy, the cooling rate in casting and the gravity number. The casting mechanism is explained in terms of the microstructures of the Al-Al3Ni and Al-Al2Cu FGMs fabricated by this method. The corrosion behavior of the FGMs was investigated by electrochemical analysis. Polarization curves of the FGMs in a borate solution were measured by a potentiodynamic method. The presence of Al2Cu exerted a larger effect on the corrosion behavior of the FGMs than Al3Ni. Analysis of the polarization curve parameters was effective for evaluating the corrosion resistance of the FGMs.

  4. Ab initio modeling of zincblende AlN layer in Al-AlN-TiN multilayers

    NASA Astrophysics Data System (ADS)

    Yadav, S. K.; Wang, J.; Liu, X.-Y.

    2016-06-01

    An unusual growth mechanism of metastable zincblende AlN thin film by diffusion of nitrogen atoms into Al lattice is established. Using first-principles density functional theory, we studied the possibility of thermodynamic stability of AlN as a zincblende phase due to epitaxial strains and interface effect, which fails to explain the formation of zincblende AlN. We then compared the formation energetics of rocksalt and zincblende AlN in fcc Al through direct diffusion of nitrogen atoms to Al octahedral and tetrahedral interstitials. The formation of a zincblende AlN thin film is determined to be a kinetically driven process, not a thermodynamically driven process.

  5. High Density Sliding at Ta/Al and Al/Al Interfaces

    SciTech Connect

    Hammerberg, J. E.; Germann, T. C.; Ravelo, R.

    2006-07-28

    We present 3D-nonequilibrium molecular dynamics results for the velocity dependence of the frictional force at smooth sliding interfaces for Ta and Al single crystals. For Ta/Al we consider Al(100)/Ta(100) and Al(111)/Ta(110) interfaces sliding along [001] and [11(bar sign)0]fcc /[001]bcc respectively. These are compared with Al(111)/Al(100) interfaces at the same loads, corresponding to a pressure of 15 GPa. Both interfacial pairs show similar behavior in the velocity dependence of the frictional force: a low velocity regime with an increasing frictional force followed by a strain induced transformation regime at velocities above approximately 1/10 the transverse sound speed, followed by a fluidized interface at high velocities. For both interfacial pairs, the high velocity dependence of the frictional force exhibits power law behavior, Ft {proportional_to} v-{beta} with {beta}=3/4. We discuss the structural changes that influence dissipation in each of these regimes.

  6. Superconductivity in Al/Al2O3 interface

    NASA Astrophysics Data System (ADS)

    Palnichenko, A. V.; Vyaselev, O. M.; Mazilkin, A. A.; Khasanov, S. S.

    2016-06-01

    Metastable superconductivity at Tc ≈ 65 K has been observed in Al foil subjected to special oxidation process, according to the ac magnetic susceptibility and electrical resistance measurements. Comparison of the ac susceptibility and the dc magnetization measurements infers that the superconductivity arises within the interfacial granular layer formed during the oxidation process between metallic aluminum and its oxide.

  7. AlN/Fe/AlN nanostructures for magnetooptic magnetometry

    SciTech Connect

    Lišková-Jakubisová, E. Višňovský, Š.; Široký, P.; Hrabovský, D.; Pištora, J.

    2014-05-07

    AlN/Fe/AlN/Cu nanostructures with ultrathin Fe grown by sputtering on Si substrates are evaluated as probes for magnetooptical (MO) mapping of weak currents. They are considered for a laser wavelength of λ = 410 nm (3.02 eV) and operate at oblique light incidence angles, φ{sup (0)}, to enable detection of both in-plane and out-of-plane magnetization. Their performance is evaluated in terms of MO reflected wave electric field amplitudes. The maximal MO amplitudes in AlN/Fe/AlN/Cu are achieved by a proper choice of layer thicknesses. The nanostructures were characterized by MO polar Kerr effect at φ{sup (0)} ≈ 5° and longitudinal Kerr effect spectra (φ{sup (0)} = 45°) at photon energies between 1 and 5 eV. The nominal profiles were refined using a model-based analysis of the spectra. Closed form analytical expressions are provided, which are useful in the search for maximal MO amplitudes.

  8. ALS - A unique design approach

    NASA Astrophysics Data System (ADS)

    Chamberlain, Roger A.

    1990-09-01

    An advanced launch system (ALS), which is intended to be flexible and to deliver a wide range of payloads at a reduced cost, is discussed. The ALS concept also features total quality management, modular subsystems, standardized interfaces, standardized missions, and off-line payload encapsulation. The technological improvements include manufacturing of dry structures, use of composite materials, adaptive guidance and control systems, and laser-initiated radar systems. The operational improvements range from paperless management, to rocket engine leak detection devices and automated ground operations.

  9. Dynamic Modeling of ALS Systems

    NASA Technical Reports Server (NTRS)

    Jones, Harry

    2002-01-01

    The purpose of dynamic modeling and simulation of Advanced Life Support (ALS) systems is to help design them. Static steady state systems analysis provides basic information and is necessary to guide dynamic modeling, but static analysis is not sufficient to design and compare systems. ALS systems must respond to external input variations and internal off-nominal behavior. Buffer sizing, resupply scheduling, failure response, and control system design are aspects of dynamic system design. We develop two dynamic mass flow models and use them in simulations to evaluate systems issues, optimize designs, and make system design trades. One model is of nitrogen leakage in the space station, the other is of a waste processor failure in a regenerative life support system. Most systems analyses are concerned with optimizing the cost/benefit of a system at its nominal steady-state operating point. ALS analysis must go beyond the static steady state to include dynamic system design. All life support systems exhibit behavior that varies over time. ALS systems must respond to equipment operating cycles, repair schedules, and occasional off-nominal behavior or malfunctions. Biological components, such as bioreactors, composters, and food plant growth chambers, usually have operating cycles or other complex time behavior. Buffer sizes, material stocks, and resupply rates determine dynamic system behavior and directly affect system mass and cost. Dynamic simulation is needed to avoid the extremes of costly over-design of buffers and material reserves or system failure due to insufficient buffers and lack of stored material.

  10. Large rectification magnetoresistance in nonmagnetic Al/Ge/Al heterojunctions

    NASA Astrophysics Data System (ADS)

    Zhang, Kun; Li, Huan-Huan; Grünberg, Peter; Li, Qiang; Ye, Sheng-Tao; Tian, Yu-Feng; Yan, Shi-Shen; Lin, Zhao-Jun; Kang, Shi-Shou; Chen, Yan-Xue; Liu, Guo-Lei; Mei, Liang-Mo

    2015-09-01

    Magnetoresistance and rectification are two fundamental physical properties of heterojunctions and respectively have wide applications in spintronics devices. Being different from the well known various magnetoresistance effects, here we report a brand new large magnetoresistance that can be regarded as rectification magnetoresistance: the application of a pure small sinusoidal alternating-current to the nonmagnetic Al/Ge Schottky heterojunctions can generate a significant direct-current voltage, and this rectification voltage strongly varies with the external magnetic field. We find that the rectification magnetoresistance in Al/Ge Schottky heterojunctions is as large as 250% at room temperature, which is greatly enhanced as compared with the conventional magnetoresistance of 70%. The findings of rectification magnetoresistance open the way to the new nonmagnetic Ge-based spintronics devices of large rectification magnetoresistance at ambient temperature under the alternating-current due to the simultaneous implementation of the rectification and magnetoresistance in the same devices.

  11. AlSb/InAs/AlSb quantum wells

    NASA Technical Reports Server (NTRS)

    Kroemer, Herbert

    1990-01-01

    Researchers studied the InAs/AlSb system recently, obtaining 12nm wide quantum wells with room temperature mobilities up to 28,000 cm(exp 2)/V center dot S and low-temperature mobilities up to 325,000 cm(exp 2)/V center dot S, both at high electron sheet concentrations in the 10(exp 12)/cm(exp 2) range (corresponding to volume concentrations in the 10(exp 18)/cm(exp 2) range). These wells were not intentionally doped; the combination of high carrier concentrations and high mobilities suggest that the electrons are due to not-intentional modulation doping by an unknown donor in the AlSb barriers, presumably a stoichiometric defect, like an antisite donor. Inasmuch as not intentionally doped bulk AlSb is semi-insulating, the donor must be a deep one, being ionized only by draining into the even deeper InAs quantum well. The excellent transport properties are confirmed by other observations, like excellent quantum Hall effect data, and the successful use of the quantum wells as superconductive weak links between Nb electrodes, with unprecendentedly high critical current densities. The system is promising for future field effect transistors (FETs), but many processing problems must first be solved. Although the researchers have achieved FETs, the results so far have not been competitive with GaAs FETs.

  12. The effect of Si in Al-alloy on electromigration performance in Al filled vias

    NASA Astrophysics Data System (ADS)

    Kageyama, Makiko; Hashimoto, Keiichi; Onoda, Hiroshi

    1998-01-01

    Electromigration performance of vias filled with Al-Si-Cu alloys on Ti glue layers was investigated in comparison with W-stud vias. In Al-Si-Cu filled vias, voids were formed at only a few locations in the test structure, while voids were formed at every via in W-stud via chains. It is supposed that Al moves through the Al-Si-Cu via during electromigration in spite of the existence of a glue layer at the via bottom. This phenomenon was observed only in the vias filled with Al-Si-Cu alloy. Al movement was prohibited in Al-Cu filled vias. In Al-Si-Cu filled vias, an Al-Ti-Si alloy was formed at the via bottom while Al3Ti was formed at Al-Cu filled vias. Al is speculated to move through this Al-Ti-Si alloy during electromigration.

  13. Emerging mechanisms of molecular pathology in ALS

    PubMed Central

    Peters, Owen M.; Ghasemi, Mehdi; Brown, Robert H.

    2015-01-01

    Amyotrophic lateral sclerosis (ALS) is a devastating degenerative disease characterized by progressive loss of motor neurons in the motor cortex, brainstem, and spinal cord. Although defined as a motor disorder, ALS can arise concurrently with frontotemporal lobal dementia (FTLD). ALS begins focally but disseminates to cause paralysis and death. About 10% of ALS cases are caused by gene mutations, and more than 40 ALS-associated genes have been identified. While important questions about the biology of this disease remain unanswered, investigations of ALS genes have delineated pathogenic roles for (a) perturbations in protein stability and degradation, (b) altered homeostasis of critical RNA- and DNA-binding proteins, (c) impaired cytoskeleton function, and (d) non-neuronal cells as modifiers of the ALS phenotype. The rapidity of progress in ALS genetics and the subsequent acquisition of insights into the molecular biology of these genes provide grounds for optimism that meaningful therapies for ALS are attainable. PMID:25932674

  14. Ab initio modeling of zincblende AlN layer in Al-AlN-TiN multilayers

    DOE PAGESBeta

    Yadav, S. K.; Wang, J.; Liu, X. -Y.

    2016-06-14

    An unusual growth mechanism of metastable zincblende AlN thin film by diffusion of nitrogen atoms into Al lattice is established. Using first-principles density functional theory, we studied the possibility of thermodynamic stability of AlN as a zincblende phase due to epitaxial strains and interface effect, which fails to explain the formation of zincblende AlN. We then compared the formation energetics of rocksalt and zincblende AlN in fcc Al through direct diffusion of nitrogen atoms to Al octahedral and tetrahedral interstitials. Furthermore, the formation of a zincblende AlN thin film is determined to be a kinetically driven process, not a thermodynamicallymore » driven process.« less

  15. Synthesis of AlN/Al Polycrystals along with Al Nanoparticles Using Thermal Plasma Route

    SciTech Connect

    Kanhe, Nilesh S.; Nawale, A. B.; Kulkarni, N. V.; Bhoraskar, S. V.; Mathe, V. L.; Das, A. K.

    2011-07-15

    This paper for the first time reports the (200) oriented growth of hexagonal Aluminum nitride crystals during synthesis of aluminum nanoparticles in dc transferred arc thermal plasma reactor by gas phase condensation in nitrogen plasma. The structural and morphological study of as synthesized AlN crystal and aluminium nanoparticles was done by using the x-ray diffraction method, scanning electron microscopy and transmission electron microscopy.

  16. Investigation of Wear Anisotropy in a Severely Deformed Al-Al3Ti Composite

    NASA Astrophysics Data System (ADS)

    El-Hadad, Shimaa; Sato, Hisashi; Watanabe, Yoshimi

    2012-09-01

    In the current investigation, Al-Al3Ti composite was processed by equal channel angular pressing (ECAP). ECAP was carried out using routes A and BC up to eight passes of deformation. It was observed that increasing the number of ECAP passes causes fragmentation of Al3Ti platelet particles and decreases their sizes compared to their original sizes in the undeformed Al-Al3Ti specimens. Moreover, the microstructure of route A-ECAPed Al-Al3Ti composite samples showed a strong alignment of the fragmented Al3Ti particles parallel to the pressing axis. On the other hand, ECAPed Al-Al3Ti alloy specimens by route BC have a relatively homogeneous distribution of Al3Ti particles. Because of the platelet Al3Ti particle fragmentation by ECAP, all the ECAPed specimens showed small anisotropy in their wear property in spite of this observed anisotropic microstructure induced by route A-ECAP.

  17. Investigation of Wear Anisotropy in a Severely Deformed Al-Al3Ti Composite

    NASA Astrophysics Data System (ADS)

    El-Hadad, Shimaa; Sato, Hisashi; Watanabe, Yoshimi

    2012-05-01

    In the current investigation, Al-Al3Ti composite was processed by equal channel angular pressing (ECAP). ECAP was carried out using routes A and BC up to eight passes of deformation. It was observed that increasing the number of ECAP passes causes fragmentation of Al3Ti platelet particles and decreases their sizes compared to their original sizes in the undeformed Al-Al3Ti specimens. Moreover, the microstructure of route A-ECAPed Al-Al3Ti composite samples showed a strong alignment of the fragmented Al3Ti particles parallel to the pressing axis. On the other hand, ECAPed Al-Al3Ti alloy specimens by route BC have a relatively homogeneous distribution of Al3Ti particles. Because of the platelet Al3Ti particle fragmentation by ECAP, all the ECAPed specimens showed small anisotropy in their wear property in spite of this observed anisotropic microstructure induced by route A-ECAP.

  18. NiAl-base composite containing high volume fraction of AlN for advanced engines

    NASA Technical Reports Server (NTRS)

    Hebsur, Mohan (Inventor); Whittenbeger, John D. (Inventor); Lowell, Carl F. (Inventor)

    1994-01-01

    A particulate reinforced NiAl-AlN composite alloy has a NiAl matrix and greater than about 13 volume percent fine particles of AlN within the matrix. The particles preferably have a diameter from about 15 nanometers to about 50 nanometers. The particulate reinforced NiAl-AlN composite alloy may be prepared by cryomilling prealloyed NiAl in liquid nitrogen using grinding media having a diameter of from about 2 to 6 mm at an impeller speed of from about 450 RPM to about 800 RPM. The cryomilling may be done for a duration of from about 4 hours to about 20 hours to obtain a cryomilled powder. The cryomilled powder may be consolidated to form the particulate reinforced NiAl-AlN composite alloy. The particulate reinforced alloy can further include a toughening alloy. The toughening alloy may include NiCrAlY, FeCrAlY, and FeAl.

  19. Synthesis of Al-Al2O3 and Al-Aln Nanoparticle Composites Via Electric Explosion of Wires

    NASA Astrophysics Data System (ADS)

    Lerner, M. I.; Lozhkomoev, A. S.; Pervikov, A. V.; Bakina, O. V.

    2016-07-01

    Composite Al-Al2O3 and Al-AlN nanoparticles were synthesized via electric explosion of aluminum wires in an argon-oxygen gas mixture and in nitrogen. The parameters of electric explosion and gas medium affect the size and relative content of nitride and aluminum oxide in the nanoparticles. Processes of forming chemical compounds during aluminum oxidation at the contact surface between explosive products and gas and of nitrogen diffusions into the nanoparticles of the condensed phase are considered.

  20. 77 FR 73732 - In the Matter of Amendment of the Designation of al-Qa'ida in Iraq, aka Jam'at al Tawhid wa'al...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-12-11

    ... Matter of Amendment of the Designation of al-Qa'ida in Iraq, aka Jam'at al Tawhid wa'al-Jihad, aka The... al-Rafidayn, aka The Organization of al-Jihad's Base of Operations in Iraq, aka al-Qaida of Jihad in Iraq, aka al-Qaida in Iraq, aka al-Qaida in Mesopotamia, aka al-Qaida in the Land of the Two...

  1. The Al-Al3Ni Eutectic Reaction: Crystallography and Mechanism of Formation

    NASA Astrophysics Data System (ADS)

    Fan, Yangyang; Makhlouf, Makhlouf M.

    2015-09-01

    The characteristics of the Al-Al3Ni eutectic structure are examined with emphasis on its morphology and crystallography. Based on these examinations, the mechanism of formation of this technologically important eutectic is postulated. It is found that a thin shell of α-Al forms coherently around each Al3Ni fiber. The excellent thermal stability of the Al-Al3Ni eutectic may be attributed to the presence of this coherent layer.

  2. Reply to Pachai et al.

    PubMed

    Harrison, William J; Bex, Peter J

    2016-05-01

    Peripheral vision is fundamentally limited by the spacing between objects. When asked to report a target's identity, observers make erroneous reports that sometimes match the identity of a nearby distractor and sometimes match a combination of target and distractor features. The classification of these errors has previously been used to support competing 'substitution' [1] or 'averaging' [2] models of the phenomenon known as 'visual crowding'. We recently proposed a single model in which both classes of error occur because observers make their reports by sampling from a biologically-plausible population of weighted responses within a region of space around the target [3]. It is critical to note that there is no probabilistic substitution or averaging process in our model; instead, we argue that neither substitution nor averaging occur, but that these are misclassifications of the distribution of reports that emerge when a population response distribution is sampled. This is a fundamentally different way of thinking about crowding, and on this basis we claim to have provided a mechanism unifying categorically distinct perceptual errors. Our goal was not to model all crowding phenomena, such as the release from crowding when target and flanks differ in color or depth [4]. Pachai et al.[5] have suggested that our model is not unifying because it inaccurately predicts perceptual performance for a particular stimulus. Although we agree that our model does not predict their data, this specific demonstration overlooks the critical aspect of the model: perceptual reports are drawn from a weighted population code. We show that Pachai et al.'s [5] own data actually provide evidence for the population code we have described [3], and we suggest a biologically-plausible analysis of their stimuli that provides a computational basis for their 'grouping' account of crowding. PMID:27166690

  3. Effects of the Al content on pore structures of porous TieAl alloys

    SciTech Connect

    Jaing, Y; He, Y H; Xu, N P; Zou, J; Huang, B; Lui, C T

    2008-01-01

    Porous TieAl alloys with different nominal compositions were fabricated through a reactive synthesis of Ti and Al elemental powders. It has been found that the pore parameters vary with the Al contents, indicating that the nature of the pores can be manipulated through changing the Al contents. In addition, detailed structural characterizations showed that the fabricated porous TieAl alloys can have three crystalline phases (i.e., a2-Ti3Al, g-TiAl, and TiAl3) when using different compositions. The fundamental reasons behind these phenomena have been explored.

  4. Everyday Life with ALS: A Practical Guide

    MedlinePlus

    ... course of ALS. ALS also will require some adaptations to your environment, both for safety and to ... the way, Chapter 6 will include information on adaptations for computer access. Though the chapter is called “ ...

  5. Benefits for Military Veterans with ALS

    MedlinePlus

    ... Chapters Certified Centers and Clinics Support Groups About ALS About Us Our Research In Your Community Advocate ... Veterans Resources for Military Veterans, Families & Survivors The ALS Association is working everyday to support people with ...

  6. Aluminium distribution in ZSM-5 revisited: The role of Al-Al interactions

    SciTech Connect

    Ruiz-Salvador, A. Rabdel; Grau-Crespo, Ricardo; Gray, Aileen E.; Lewis, Dewi W.

    2013-02-15

    We present a theoretical study of the distribution of Al atoms in zeolite ZSM-5 with Si/Al=47, where we focus on the role of Al-Al interactions rather than on the energetics of Al/Si substitutions at individual sites. Using interatomic potential methods, we evaluate the energies of the full set of symmetrically independent configurations of Al siting in a Si{sub 94}Al{sub 2}O{sub 192} cell. The equilibrium Al distribution is determined by the interplay of two factors: the energetics of the Al/Si substitution at an individual site, which tends to populate particular T sites (e.g., the T14 site), and the Al-Al interaction, which at this Si/Al maximises Al-Al distances in general agreement with Dempsey's rule. However, it is found that the interaction energy changes approximately as the inverse of the square of the distance between the two Al atoms, rather than the inverse of the distance expected if this were merely charge repulsion. Moreover, we find that the anisotropic nature of the framework density plays an important role in determining the magnitude of the interactions, which are not simply dependent on Al-Al distances. - Graphical abstract: Role of Al-Al interactions in high silica ZSM-5 is shown to be anisotropic in nature and not dependent solely on Coulombic interactions. Highlights: Black-Right-Pointing-Pointer Si-Al distribution in ZSM-5 is revisited, stressing the role of the Al-Al interaction. Black-Right-Pointing-Pointer Coulomb interactions are not the key factors controlling the Al siting. Black-Right-Pointing-Pointer Anisotropy of the framework is identified as a source of departure from Dempsey's rule.

  7. Photoelectrical, photophysical and photocatalytic properties of Al based MOFs: MIL-53(Al) and MIL-53-NH2(Al)

    NASA Astrophysics Data System (ADS)

    An, Yang; Li, Huiliang; Liu, Yuanyuan; Huang, Baibiao; Sun, Qilong; Dai, Ying; Qin, Xiaoyan; Zhang, Xiaoyang

    2016-01-01

    Two Al based MOFs (MIL-53(Al) and MIL-53-NH2 (Al)) were synthesized, and their photoelectrical, photophysical and photocatalytic properties towards oxygen evolution from water were investigated. Different from the ligand to metal charge transfer process previously reported, we proposes a new photocatalytic mechanism based on electron tunneling according to the results of theoretical calculation, steady state and time resolved fluorescence spectra. The organic linkers absorb photons, giving rise to electrons and holes. Then, the photogenerated electrons tunnel through the AlO6-octahedra, which not only inhibit the recombination of photogenerated charge carriers, but also is a key factor to the photocatalytic activity of Al based MOFs.

  8. Nonstoichiometry of Al-Zr intermetallic phases

    SciTech Connect

    Radmilovic, V.; Thomas, G.

    1994-06-01

    Nonstoichiometry of metastable cubic {beta}{prime} and equilibrium tetragonal {beta} Al-Zr intermetallic phases of the nominal composition Al{sub 3}Zr in Al-rich alloys has been extensively studied. It is proposed that the ``dark contrast`` of {beta}{prime} core in {beta}{prime}/{sigma}{prime} complex precipitates, in Al-Li-Zr based alloys, is caused by incorporation of Al and Li atoms into the {beta}{prime} phase on Zr sublattice sites, forming nonstoichiometric Al-Zr intermetallic phases, rather than by Li partitioning only. {beta}{prime} particles contain very small amounts of Zr, approximately 5 at.%, much less than the stoichiometric 25 at.% in the Al{sub 3}Zr metastable phase. These particles are, according to simulation of high resolution images, of the Al{sub 3}(Al{sub 0.4}Li{sub 0.4}Zr{sub 0.2}) type. Nonstoichiometric particles of average composition Al{sub 4}Zr and Al{sub 6}Zr are observed also in the binary Al-Zr alloy, even after annealing for several hours at 600{degree}C.

  9. Cyclic oxidation resistance of a reaction milled NiAl-AlN composite

    NASA Technical Reports Server (NTRS)

    Lowell, Carl E.; Barrett, Charles A.; Whittenberger, J. D.

    1990-01-01

    Based upon recent mechanical property tests a NiAl-AlN composite produced by cryomilling has very attractive high temperature strength. This paper focuses on the oxidation resistance of the NiAl-AlN composite at 1473 and 1573 K as compared to that of Ni-47Al-0.15Zr, one of the most oxidation resistant intermetallics. The results of cyclic oxidation tests show that the NiAl-AlN composite has excellent properties although not quite as good as those of Ni-47Al-0.15Zr. The onset of failure of the NiAl-AlN was unique in that it was not accompanied by a change in scale composition from alumina to less protective oxides. Failure in the composite appears to be related to the entrapment of AlN particles within the alumina scale.

  10. Cenomanian-Turonian biostratigraphy of the Jardas Al Abid area, Al Jabal Al Akhdar, northeast Libya

    NASA Astrophysics Data System (ADS)

    El Qot, Gamal M.; Abdulsamad, Esam O.

    2016-09-01

    The Upper Cenomanian-Turonian succession exposed at Jardas al'Abid area consists mainly of carbonates with siliciclastic intercalations. This succession is subdivided lithostratigraphically into: Qasr al'Abid (Late Cenomanian) and Al Baniyah (Late Cenomanian-Coniacian) formations. This sequence is relatively rich in macrofossil assemblages especially bivalves, gastropods, and echinoids with rare ammonites. Based on the first occurrence (FO) and last occurrence (LO) of some index species of these macrofossil groups, an integrated biostratigraphic framework has been constructed. The studied Cenomanian-Turonian sequence is subdivided biostratigraphically into three ammonite biozones; Pseudaspidoceras pseudonodosoides Total Range Zone, Choffaticeras segne Total Range Zone, and Coilopoceras requienianum Total Range Zone. Based on the rest of macrofossil assemblages other than the ammonites, eight biozones were recognized; Mecaster batnensis Total Range Zone, Ceratostreon flabellatum-Neithea dutrugei Acme Zone, Costagyra olisiponensis Acme Zone, Pycnodonte (Phygraea) vesicularis vesiculosa Acme Zone, Mytiloides labiatus Total Range Zone = Mecaster turonensis Acme Zone, Rachiosoma rectilineatum-Curvostrea rouvillei-Tylostoma (T.) globosum Assemblage Zone, Radiolites sp.-Apricardia? matheroni Total Range Zone, and Nerinea requieniana Total Range Zone. Most of the proposed biozones are recorded for the first time from Libya. The integration among these biozones as well as local and inter-regional correlation of the biozones have been discussed. The stage boundaries of the studied stratigraphic intervals are discussed, where the Cenomanian/Turonian boundary is delineated at the last occurrence (LO) of Pseudaspidoceras pseudonodosoides (Choffat), while the Turonian/Coniacian boundary is delineated arbitrary being agree with the LO of the Turonian fauna.

  11. Systems Engineering Techniques for ALS Decision Making

    NASA Technical Reports Server (NTRS)

    Rodriquez, Luis F.; Drysdale, Alan E.; Jones, Harry; Levri, Julie A.

    2004-01-01

    The Advanced Life Support (ALS) Metric is the predominant tool for predicting the cost of ALS systems. Metric goals for the ALS Program are daunting, requiring a threefold increase in the ALS Metric by 2010. Confounding the problem, the rate new ALS technologies reach the maturity required for consideration in the ALS Metric and the rate at which new configurations are developed is slow, limiting the search space and potentially giving the perspective of a ALS technology, the ALS Metric may remain elusive. This paper is a sequel to a paper published in the proceedings of the 2003 ICES conference entitled, "Managing to the metric: an approach to optimizing life support costs." The conclusions of that paper state that the largest contributors to the ALS Metric should be targeted by ALS researchers and management for maximum metric reductions. Certainly, these areas potentially offer large potential benefits to future ALS missions; however, the ALS Metric is not the only decision-making tool available to the community. To facilitate decision-making within the ALS community a combination of metrics should be utilized, such as the Equivalent System Mass (ESM)-based ALS metric, but also those available through techniques such as life cycle costing and faithful consideration of the sensitivity of the assumed models and data. Often a lack of data is cited as the reason why these techniques are not considered for utilization. An existing database development effort within the ALS community, known as OPIS, may provide the opportunity to collect the necessary information to enable the proposed systems analyses. A review of these additional analysis techniques is provided, focusing on the data necessary to enable these. The discussion is concluded by proposing how the data may be utilized by analysts in the future.

  12. Opportunity's 'Rub al Khali' Panorama

    NASA Technical Reports Server (NTRS)

    2005-01-01

    [figure removed for brevity, see original site] Click on the image for Opportunity's 'Rub al Khali' Panorama (QTVR)

    This panoramic image, dubbed 'Rub al Khali,' was acquired by NASA's Mars Exploration Rover Opportunity on the plains of Meridiani during the period from the rover's 456th to 464th sols on Mars (May 6 to May 14, 2005). Opportunity was about 2 kilometers (1.2 miles) south of 'Endurance Crater' at a place known informally as 'Purgatory Dune.'

    The rover was stuck in the dune's deep fine sand for more than a month. 'Rub al Khali' (Arabic translation: 'the empty quarter') was chosen as the name for this panorama because it is the name of a similarly barren, desolate part of the Saudi Arabian desert on Earth.

    The view spans 360 degrees. It consists of images obtained in 97 individual pointings of the panoramic camera. The camera took images with five camera filters at each pointing. This 22,780-by-6,000-pixel mosaic is an approximately true-color rendering generated using the images acquired through filters admitting light wavelengths of 750, 530, and 480 nanometers.

    Lighting varied during the nine sols it took to acquire this panorama, resulting in some small image seams within the mosaic. These seams have been smoothed in sky parts of the mosaic to better simulate the vista that a person would see if able to view it all at the same time on Mars.

    Opportunity's tracks leading back to the north (center of the panorama) are a reminder of the rover's long trek from Endurance Crater. The deep ruts dug by Opportunity's wheels as it became stuck in the sand appear in the foreground. The crest and trough of the last ripple the rover crossed before getting stuck is visible in the center. These wind-formed sand features are only about 10 to 15 centimeters (4 to 6 inches) tall. The crest of the actual ripple where the rover got stuck can be seen just to the right of center. The tracks and a few other places on and near ripple crests can

  13. Magnetism of Al-substituted magnetite reduced from Al-hematite

    NASA Astrophysics Data System (ADS)

    Jiang, Zhaoxia; Liu, Qingsong; Zhao, Xiang; Roberts, Andrew P.; Heslop, David; Barrón, Vidal; Torrent, José

    2016-06-01

    Aluminum-substituted magnetite (Al-magnetite) reduced from Al-substituted hematite or goethite (Al-hematite or Al-goethite) is an environmentally important constituent of magnetically enhanced soils. In order to characterize the magnetic properties of Al-magnetite, two series of Al-magnetite samples were synthesized through reduction of Al-hematite by a mixed gas (80% CO2 and 20% CO) at 395°C for 72 h in a quartz tube furnace. Al-magnetite samples inherited the morphology of their parent Al-hematite samples, but only those transformed from Al-hematite synthesized at low temperature possessed surficial micropores, which originated from the release of structural water during heating. Surface micropores could thus serve as a practical fingerprint of fire or other high-temperature mineralogical alteration processes in natural environments, e.g., shear friction in seismic zones. In addition, Al substitution greatly affects the magnetic properties of Al-magnetite. For example, coercivity (Bc) increases with increasing Al content and then decreases slightly, while the saturation magnetization (Ms), Curie temperature (Tc), and Verwey transition temperature (Tv) all decrease with increasing Al content due to crystal defect formation and dilution of magnetic ions caused by Al incorporation. Moreover, different trends in the correlation between Tc and Bc can be used to discriminate titanomagnetite from Al-magnetite, which is likely to be important in environmental and paleomagnetic studies, particularly in soil.

  14. Reactive Plasma Spraying of Fine Al2O3/AlN Feedstock Powder

    NASA Astrophysics Data System (ADS)

    Shahien, Mohammed; Yamada, Motohiro; Yasui, Toshiaki; Fukumoto, Masahiro

    2013-12-01

    Reactive plasma spraying (RPS) is a promising technology for in situ formation of aluminum nitride (AlN) coatings. Recently, AlN-based coatings were fabricated by RPS of alumina (Al2O3) powder in N2/H2 thermal plasma. This study investigated the feasibility of RPS of a fine Al2O3/AlN mixture and the influence of the plasma gases (N2, H2) on the nitriding conversion, and coating microstructure and properties. Thick AlN/Al2O3 coatings with high nitride content were successfully fabricated. The coatings consist of h-AlN, c-AlN, Al5O6N, γ-Al2O3, and a small amount of α-Al2O3. Use of fine particles enhanced the nitriding conversion and the melting tendency by increasing the surface area. Furthermore, the AlN additive improved the AlN content in the coatings. Increasing the N2 gas flow rate improved the nitride content and complete crystal growth to the h-AlN phase, and enhanced the coating thickness. On the other hand, though the H2 gas is required for plasma nitriding of the Al2O3 particles, increasing its flow rate decreased the nitride content and the coating thickness. Remarkable influence of the plasma gases on the coating composition, microstructure, and properties was observed during RPS of the fine particles.

  15. Immunomodulatory drugs in AL amyloidosis.

    PubMed

    Jelinek, T; Kufova, Z; Hajek, R

    2016-03-01

    Immunoglobulin light chain amyloidosis (AL amyloidosis) is indeed a rare plasma cell disorder, yet the most common of the systemic amyloidoses. The choice of adequate treatment modality is complicated and depends dominantly on the risk stratification of these fragile patients. Immunomodulatory drugs (IMiDs) are currently used in newly diagnosed patients as well as in salvage therapy in relapsed/refractory patients. IMiDs have a pleiotropic effect on malignant cells and the exact mechanism of their action has been described recently. Thalidomide is the most ancient representative, effective but toxic. Lenalidomide seems to be more effective, nevertheless the toxicity remains high, especially in patients with renal insufficiency. Pomalidomide is the newest IMiD used in this indication with a good balance between efficacy and tolerable toxicity and represents the most promising compound. This review is focused on the evaluation of all three representatives of IMiDs and their roles in the treatment of this malignant disorder. PMID:26806146

  16. Instandhaltungsmanagement als Gestaltungsfeld Ganzheitlicher Produktionssysteme

    NASA Astrophysics Data System (ADS)

    Dombrowski, Uwe; Schulze, Sven; Otano, Isabel Crespo

    Sich kontinuierlich verändernde Rahmenbedingungen, wie beispielsweise eine steigende Variantenvielfalt, verkürzte Produktlebenszyklen sowie Kundenforderungen nach höherer Qualität, kürzeren Lieferzeiten und geringeren Kosten, fordern von produzierenden Unternehmen eine stetige Anpassung der Prozesse, der Organisation und der Strukturen. Seit den 90er Jahren versuchen immer mehr deutsche Unternehmen diesen veränderten Anforderungen mit der Einführung eines Ganzheitlichen Produktionssystems (GPS) zu begegnen. Ganzheitliche Produktionssysteme sind dabei in ihren Grundlagen an das Toyota Produktionssystem angelehnt, vereinigen aber auch weitere Methoden zu einem unternehmensspezifischen Regelwerk. Im Rahmen des langfristigen Trends zu unternehmensindividuellen Produktionssystemen wird sowohl in der Industrie als auch in der Forschung intensiv über das Toyota Produktionssystem, Lean Production, Lean Management und Ganzheitliche Produktionssysteme diskutiert, werden Konzepte zu Implementierung und Betrieb erstellt und die Wirtschaftlichkeit untersucht.

  17. Accumulation of Al in Root Mucilage of an Al-Resistant and an Al-Sensitive Cultivar of Wheat.

    PubMed Central

    Archambault, D. J.; Zhang, G.; Taylor, G. J.

    1996-01-01

    To estimate rates of Al accumulation within the symplasm, all apoplastic pools of Al need to be eliminated or accounted for. We have developed a revised kinetic protocol that allows us to estimate the contribution of mucilage-bound Al to total, nonexchangeable Al, and to eliminate the mucilage as an apoplastic pool of Al. By comparing the Al content of excised root tips (2 cm) of wheat (Triticum aestivum L.) with and without the removal of the mucilage (using a 10-min wash in 1 M NH4Cl), we found that Al bound to the mucilage accounted for approximately 25 to 35% of Al remaining after desorption in citric acid. The kinetics of Al uptake into mucilage were biphasic, with a rapid phase occurring in the first 30 min of uptake, followed by a linear phase occurring in the remainder of the experimental period (180 min). By adopting a step for removal of mucilage into our existing kinetic protocol, we have been able to isolate a linear phase of uptake with only a slight deviation from linearity in the first 5 min. Although we cannot unambiguously identify this phase of uptake as uptake into the symplasm, we believe this new protocol provides us with the most accurate quantitative estimate of symplastic Al yet available. PMID:12226458

  18. Al/Al-N/AlN compositional gradient film synthesized by ion-beam assisted deposition method

    SciTech Connect

    Amamoto, Yoshiki; Uchiyama, Shingo; Watanabe, Yoshihisa; Nakamura, Yoshikazu

    1997-12-01

    Al/Al-N-AlN compositional gradient thin film was deposited on a Si(100) substrate at room temperature by ion-beam assisted deposition method, with a diminishing ion beam current from 1.4 to 0 mA at increments of 0.3 mA in order to gradually decrease the nitrogen to aluminum ratio at the substrate. The gradual Al and AlN variation in composition was shown by the change of the Al/N atomic ratio analyzed by the energy dispersive X-ray spectroscopy (EDX) and the X-ray photoelectron spectroscopy (XPS) in the cross section of the film. The formation of crystalline Al metal and AlN ceramic layer on the Si substrate was revealed by X-ray diffraction (XRD). The cross sectional image taken by high resolution transmission electron microscope (HRTEM) showed a nano-sized crystalline Al-N ceramic material and the flat interface between the Si substrate and the AlN film.

  19. Fabrication of Nb/AlO x/Al/AlO x/Nb junctions for voltage standard applications

    NASA Astrophysics Data System (ADS)

    Maezawa, M.; Urano, C.; Kaneko, N.; Kiryu, S.

    2007-10-01

    We present an overdamped superconductor-insulator-normal-insulator-superconductor (SINIS) junction technology for ac voltage standard applications. Modifying our standard Nb-junction process, we developed a simple process for Nb/AlOx/Al/AlOx/Nb-junction circuits. A Josephson arbitrary waveform synthesizer device which consisted of a 100-SINIS-junction array embedded in a 50 Ω coplanar waveguide was fabricated and successfully tested.

  20. Growth and stress-induced transformation of zinc blende AlN layers in Al-AlN-TiN multilayers

    SciTech Connect

    Li, Nan; Yadav, Satyesh K.; Wang, Jian; Liu, Xiang -Yang; Misra, Amit

    2015-12-18

    We report that AlN nanolayers in sputter deposited {111}Al/AlN/TiN multilayers exhibit the metastable zinc-blende-structure (z-AlN). Based on density function theory calculations, the growth of the z-AlN is ascribed to the kinetically and energetically favored nitridation of the deposited aluminium layer. In situ nanoindentation of the as-deposited {111}Al/AlN/TiN multilayers in a high-resolution transmission electron microscope revealed the z-AlN to wurzite AlN phase transformation through collective glide of Shockley partial dislocations on every two {111} planes of the z-AlN.

  1. Growth and Stress-induced Transformation of Zinc blende AlN Layers in Al-AlN-TiN Multilayers

    PubMed Central

    Li, Nan; Yadav, Satyesh K.; Wang, Jian; Liu, Xiang-Yang; Misra, Amit

    2015-01-01

    AlN nanolayers in sputter deposited {111}Al/AlN/TiN multilayers exhibit the metastable zinc-blende-structure (z-AlN). Based on density function theory calculations, the growth of the z-AlN is ascribed to the kinetically and energetically favored nitridation of the deposited aluminium layer. In situ nanoindentation of the as-deposited {111}Al/AlN/TiN multilayers in a high-resolution transmission electron microscope revealed the z-AlN to wurzite AlN phase transformation through collective glide of Shockley partial dislocations on every two {111} planes of the z-AlN. PMID:26681109

  2. Growth and Stress-induced Transformation of Zinc blende AlN Layers in Al-AlN-TiN Multilayers.

    PubMed

    Li, Nan; Yadav, Satyesh K; Wang, Jian; Liu, Xiang-Yang; Misra, Amit

    2015-01-01

    AlN nanolayers in sputter deposited {111}Al/AlN/TiN multilayers exhibit the metastable zinc-blende-structure (z-AlN). Based on density function theory calculations, the growth of the z-AlN is ascribed to the kinetically and energetically favored nitridation of the deposited aluminium layer. In situ nanoindentation of the as-deposited {111}Al/AlN/TiN multilayers in a high-resolution transmission electron microscope revealed the z-AlN to wurzite AlN phase transformation through collective glide of Shockley partial dislocations on every two {111} planes of the z-AlN. PMID:26681109

  3. Orientation relationship of eutectoid FeAl and FeAl2

    PubMed Central

    Scherf, A.; Kauffmann, A.; Kauffmann-Weiss, S.; Scherer, T.; Li, X.; Stein, F.; Heilmaier, M.

    2016-01-01

    Fe–Al alloys in the aluminium range of 55–65 at.% exhibit a lamellar microstructure of B2-ordered FeAl and triclinic FeAl2, which is caused by a eutectoid decomposition of the high-temperature Fe5Al8 phase, the so-called ∊ phase. The orientation relationship of FeAl and FeAl2 has previously been studied by Bastin et al. [J. Cryst. Growth (1978 ▸), 43, 745] and Hirata et al. [Philos. Mag. Lett. (2008 ▸), 88, 491]. Since both results are based on different crystallographic data regarding FeAl2, the data are re-evaluated with respect to a recent re-determination of the FeAl2 phase provided by Chumak et al. [Acta Cryst. (2010 ▸), C66, i87]. It is found that both orientation relationships match subsequent to a rotation operation of 180° about a 〈112〉 crystallographic axis of FeAl or by applying the inversion symmetry of the FeAl2 crystal structure as suggested by the Chumak data set. Experimental evidence for the validity of the previously determined orientation relationships was found in as-cast fully lamellar material (random texture) as well as directionally solidified material (∼〈110〉FeAl || solidification direction) by means of orientation imaging microscopy and global texture measurements. In addition, a preferential interface between FeAl and FeAl2 was identified by means of trace analyses using cross sectioning with a focused ion beam. On the basis of these habit planes the orientation relationship between the two phases can be described by (01)FeAl || (114) and [111]FeAl || [10]. There is no evidence for twinning within FeAl lamellae or alternating orientations of FeAl lamellae. Based on the determined orientation and interface data, an atomistic model of the structure relationship of Fe5Al8, FeAl and FeAl2 in the vicinity of the eutectoid decomposition is derived. This model is analysed with respect to the strain which has to be accommodated at the interface of FeAl and FeAl2. PMID:27047304

  4. Effects of Al Contents on Carburization Behavior and Corrosion Resistance of TiAl Alloys

    NASA Astrophysics Data System (ADS)

    Liao, Cui Jiao; He, Yue Hui; Ming, Xing Zu

    2015-10-01

    TiAl alloys with Al contents of 30.7, 37, 46.5, and 54.2 at.% were carburized. Corrosion resistance of the untreated and the carburized TiAl alloys was comparatively analyzed. The phase and microstructure of the carburized TiAl alloys were studied by x-ray diffraction and scanning electron microscopy, respectively. Electrochemical corrosion behavior of the untreated and the carburized TiAl alloys was investigated using potentiodynamic polarization and electrochemical impedance spectroscopy. Experimental results indicate that different Al contents bring about distinct microstructure of the carburized layers. The lower Al content leads to the formation of the thicker binary carbides and the thinner Ti2AlC phase. Additionally, the lower Al content leads to higher corrosion resistance in the untreated and the carburized states.

  5. Reply to Vance et al.

    SciTech Connect

    Woon-Chee Yee; Elliott, J.L; Kwon, J.M.; Goodfellow, P.

    1996-07-01

    In our report of a family with a motor and sensory polyneuropathy that was linked to chromosome 3q, we classified this neuropathy as a form of hereditary motor and sensory neuropathy II (HMSN II, also known as {open_quotes}CMT2{close_quotes}). Doubts have been raised by Vance et al. as to whether this neuropathy should be classified as hereditary sensory autonomic neuropathy I (HSAN I) instead of HMSN II. While it is reasonable to raise such doubts, we believe that the neuropathy is best designated as HMSN II for the reasons described below. The group of disorders described as HSAN are characterized by primary or predominant involvement of sensory and autonomic neurons that fail to develop or that undergo atrophy and degeneration. These disorders were extensively reviewed by Dyck and Ohta, who initially described them as the hereditary sensory neuropathies (HSN). It was Dyck who subsequently suggested that these disorders be designated HSAN rather than HSN, because of the presence of autonomic involvement. 8 refs.

  6. Tensile Behavior of Al2o3/feal + B and Al2o3/fecraly Composites

    NASA Technical Reports Server (NTRS)

    Draper, S. L.; Eldridge, J. I.; Aiken, B. J. M.

    1995-01-01

    The feasibility of Al2O3/FeAl + B and Al2O3/FeCrAlY composites for high-temperature applications was assessed. The major emphasis was on tensile behavior of both the monolithics and composites from 298 to 1100 K. However, the study also included determining the chemical compatibility of the composites, measuring the interfacial shear strengths, and investigating the effect of processing on the strength of the single-crystal Al2O3 fibers. The interfacial shear strengths were low for Al203/FeAl + B and moderate to high for Al203/FeCrAlY. The difference in interfacial bond strengths between the two systems affected the tensile behavior of the composites. The strength of the Al203 fiber was significantly degraded after composite processing for both composite systems and resulted in poor composite tensile properties. The ultimate tensile strength (UTS) values of the composites could generally be predicted with either rule of mixtures (ROM) calculations or existing models when using the strength of the etched-out fiber. The Al2O3/FeAl + B composite system was determined to be unfeasible due to poor interfacial shear strengths and a large mismatch in coefficient of thermal expansion (CTE). Development of the Al2O3/FeCrAlY system would require an effective diffusion barrier to minimize the fiber strength degradation during processing and elevated temperature service.

  7. A New Phase in ALS Research.

    PubMed

    Chong, P Andrew; Forman-Kay, Julie D

    2016-09-01

    In this issue of Structure, Conicella et al. (2016) present evidence that the low complexity C-terminal region of TDP-43 undergoes liquid-liquid phase separation. ALS-associated mutations alter this phase separation process, providing a possible mechanism for the pathology caused by these TDP-43 mutations. The work is strongly supportive of toxic loss of RNA processing function in ALS. PMID:27602988

  8. Memory deficits and retrieval processes in ALS.

    PubMed

    Mantovan, M C; Baggio, L; Dalla Barba, G; Smith, P; Pegoraro, E; Soraru', G; Bonometto, P; Angelini, C

    2003-05-01

    Subtle neuropsychological deficits have been described in patients affected by amyotrophic lateral sclerosis (ALS) without dementia. Overall, selective impairment in memory function has been reported, but the source of memory impairment in ALS has yet to be defined. We performed neuropsychological screening in 20 ALS patients. Semantic encoding and post-encoding cue effects on the retrieval of word lists were investigated in the ALS patients and normal controls. Severity of memory impairment was correlated to cerebral blood perfusion detected by single photon emission computed tomography (SPECT). ALS patients showed moderate impairments in frontal and memory tests. Short-term memory was normal, while serial position retrieval of word lists with normal recency effect but poor primacy effect showed long-term memory deficit. ALS patients performed better in cued encoding than in cued post-encoding recall condition. In the cued post-encoding condition, the primacy effect in word list recall improved significantly in controls, but not in ALS patients, as compared with both the free recall and cued encoding conditions. SPECT hypoperfusion was observed in frontal and temporal areas in ALS patients. ALS patients showed a long-term memory deficit which did not improve in cued post-encoding condition as it does for controls. We hypothesize abnormal retrieval processes related to frontal lobe dysfunction which entails difficulties in generating stable long-memory traces at encoding. PMID:12752394

  9. Interfacial Phenomena in Al/Al, Al/Cu, and Cu/Cu Joints Soldered Using an Al-Zn Alloy with Ag or Cu Additions

    NASA Astrophysics Data System (ADS)

    Pstruś, Janusz; Gancarz, Tomasz

    2014-05-01

    The studies of soldered joints were carried out in systems: Al/solder/Al, Al/solder/Cu, Cu/solder/Cu, where the solder was (Al-Zn)EUT, (Al-Zn)EUT with 0.5, 1.0, and 1.5 at.% of Ag and (Al-Zn)EUT with 0.5, 1.0, and 1.5 at.% of Cu addition. Brazing was performed at 500 °C for 3 min. The EDS analysis indicated that the composition of the layers starting from the Cu pad was CuZn, Cu5Zn8, and CuZn4, respectively. Wetting tests were performed at 500 °C for 3, 8, 15, and 30 min, respectively. Thickness of the layers and their kinetics of growth were measured based on the SEM micrographs. The formation of interlayers was not observed from the side of Al pads. On the contrary, dissolution of the Al substrate and migration of Al-rich particles into the bulk of the solder were observed.

  10. Al-doped ZnO nanocrystals

    NASA Astrophysics Data System (ADS)

    Kadam, Pratibha; Agashe, Chitra; Mahamuni, Shailaja

    2008-11-01

    Al3+-doped ZnO nanocrystals were differently obtained by wet chemical and an electrochemical route. An increase in forbidden gap due to change in crystal size and also due to Al3+ doping in ZnO is critically analyzed. The Moss-Burstein type shift in Al3+-doped ZnO nanocrystals provides an evidence of successful Al3+ doping in ZnO nanocrystals. The possibility of varying the carrier concentration in ZnO nanocrystals is the indirect implication of the present investigations.

  11. Genetics of Familial and Sporadic ALS

    ClinicalTrials.gov

    2016-03-21

    Amyotrophic Lateral Sclerosis (ALS); Familial Amyotrophic Lateral Sclerosis; Amyotrophic Lateral Sclerosis With Frontotemporal Dementia; Lou Gehrig's Disease; Motor Neuron Disease; Primary Lateral Sclerosis

  12. Processing and Mechanical Properties of Directionally Solidified NiAl/NiAlTa Alloys

    NASA Technical Reports Server (NTRS)

    Johnson, D. R.; Oliver, B. F.; Noebe, R. D.; Whittenberger, J. D.

    1994-01-01

    Promising creep strengths were found for a directionally solidified NiAl-NiAlTa alloy when compared to other NiAl based intermetallics. The directionally solidified alloy had an off-eutectic composition that resulted in microstructures consisting of NiAl dendrites surrounded by aligned eutectic regions. The room temperature toughness of the two phase alloy was similar to that of polycrystalline NiAl even with the presence of the brittle Laves phase NiAlTa. Alloying additions that may improve the room temperature toughness by producing multiphase alloys are discussed.

  13. Effects of the Al content on pore structures of porous TieAl alloys

    SciTech Connect

    Jiang, Y; He, Y H; Zou, J; Huang, B; Liu, C

    2008-01-01

    PorousTi Alalloys with different nominal compositions were fabricated through a reactive synthesis of Ti and Al elemental powders. It has been found that the pore parameters vary with the Al contents, indicating that the nature of the pores can be manipulated through changing the Al contents. In addition, detailed structural characterizations showed that the fabricated porousTi Alalloys can have three crystalline phases (i.e., 2-Ti3Al, -TiAl, and TiAl3) when using different compositions. The fundamental reasons behind these phenomena have been explored.

  14. Atomic structure and oxygen deficiency of the ultrathin aluminium oxide barrier in Al/AlOx/Al Josephson junctions

    PubMed Central

    Zeng, Lunjie; Tran, Dung Trung; Tai, Cheuk-Wai; Svensson, Gunnar; Olsson, Eva

    2016-01-01

    Al/AlOx/Al Josephson junctions are the building blocks of a wide range of superconducting quantum devices that are key elements for quantum computers, extremely sensitive magnetometers and radiation detectors. The properties of the junctions and the superconducting quantum devices are determined by the atomic structure of the tunnel barrier. The nanoscale dimension and disordered nature of the barrier oxide have been challenges for the direct experimental investigation of the atomic structure of the tunnel barrier. Here we show that the miniaturized dimension of the barrier and the interfacial interaction between crystalline Al and amorphous AlOx give rise to oxygen deficiency at the metal/oxide interfaces. In the interior of the barrier, the oxide resembles the atomic structure of bulk aluminium oxide. Atomic defects such as oxygen vacancies at the interfaces can be the origin of the two-level systems and contribute to decoherence and noise in superconducting quantum circuits. PMID:27403611

  15. Atomic structure and oxygen deficiency of the ultrathin aluminium oxide barrier in Al/AlOx/Al Josephson junctions

    NASA Astrophysics Data System (ADS)

    Zeng, Lunjie; Tran, Dung Trung; Tai, Cheuk-Wai; Svensson, Gunnar; Olsson, Eva

    2016-07-01

    Al/AlOx/Al Josephson junctions are the building blocks of a wide range of superconducting quantum devices that are key elements for quantum computers, extremely sensitive magnetometers and radiation detectors. The properties of the junctions and the superconducting quantum devices are determined by the atomic structure of the tunnel barrier. The nanoscale dimension and disordered nature of the barrier oxide have been challenges for the direct experimental investigation of the atomic structure of the tunnel barrier. Here we show that the miniaturized dimension of the barrier and the interfacial interaction between crystalline Al and amorphous AlOx give rise to oxygen deficiency at the metal/oxide interfaces. In the interior of the barrier, the oxide resembles the atomic structure of bulk aluminium oxide. Atomic defects such as oxygen vacancies at the interfaces can be the origin of the two-level systems and contribute to decoherence and noise in superconducting quantum circuits.

  16. Atomic structure and oxygen deficiency of the ultrathin aluminium oxide barrier in Al/AlOx/Al Josephson junctions.

    PubMed

    Zeng, Lunjie; Tran, Dung Trung; Tai, Cheuk-Wai; Svensson, Gunnar; Olsson, Eva

    2016-01-01

    Al/AlOx/Al Josephson junctions are the building blocks of a wide range of superconducting quantum devices that are key elements for quantum computers, extremely sensitive magnetometers and radiation detectors. The properties of the junctions and the superconducting quantum devices are determined by the atomic structure of the tunnel barrier. The nanoscale dimension and disordered nature of the barrier oxide have been challenges for the direct experimental investigation of the atomic structure of the tunnel barrier. Here we show that the miniaturized dimension of the barrier and the interfacial interaction between crystalline Al and amorphous AlOx give rise to oxygen deficiency at the metal/oxide interfaces. In the interior of the barrier, the oxide resembles the atomic structure of bulk aluminium oxide. Atomic defects such as oxygen vacancies at the interfaces can be the origin of the two-level systems and contribute to decoherence and noise in superconducting quantum circuits. PMID:27403611

  17. Response to Signorovitch et al.

    PubMed

    Flot, Jean-François; Debortoli, Nicolas; Hallet, Bernard; Van Doninck, Karine

    2016-08-22

    Signorovitch et al.[1] comment that an Oenothera-like meiosis [2] could produce a pattern similar to what we observed in our study of natural isolates of the bdelloid rotifer Adineta vaga, which we attributed to horizontal gene transfers (HGTs) [3]. Indeed, our HGT hypothesis appears at first sight difficult to conciliate with their observation of a congruent pattern of allele sharing at four large loci possibly located on different chromosomes [4]. However, one might imagine conditions under which massive horizontal gene transfer between bdelloid individuals could produce such a pattern, notably if the individuals involved had previously lost most of their heterozygosity because of their exposure to frequent desiccation (which produces DNA double-strand breaks [5]). In the published A. vaga genome the loss of heterozygosity due to large-scale gene conversion events or break-induced replication covers only about 10% of the genome [6], but this percentage may be much higher in environmental isolates that often experience dessication. Besides, if an Oenothera-like mode of meiosis occurs in bdelloids frequently enough to be detected in a single sampling of 29 individuals (as in [4]), one would expect males and meiosis to be observed at least occasionally, and instances of congruent allele sharing across loci should turn up frequently in genetic surveys. This was not the case in [3]: among the 82 A. vaga individuals sequenced for four nuclear markers, no trio of individuals presented congruent patterns of shared sequences at different loci. For these reasons, and in the absence of any direct evidence for an Oenothera-like meiosis in bdelloids, we still consider inter-bdelloid HGTs a more parsimonious explanation for our results. PMID:27554651

  18. 76 FR 18783 - United States et al.

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-04-05

    ... Antitrust Division United States et al. v. Dean Foods Company; Proposed Final Judgment, Stipulation and... of America, et al. v. Dean Foods Company, Civil Action No. 2:10-cv-00059 (JPS). On January 22, 2010, the United States and its co-plaintiffs filed a Complaint alleging that Dean Foods...

  19. Durability Assessment of TiAl Alloys

    NASA Technical Reports Server (NTRS)

    Draper, Susan L.; Lerch, Bradley A.

    2008-01-01

    The durability of TiAl is a prime concern for the implementation of TiAl into aerospace engines. Two durability issues, the effect of high temperature exposure on mechanical properties and impact resistance, have been investigated and the results are summarized in this paper. Exposure to elevated temperatures has been shown to be detrimental to the room temperature ductility of gamma alloys with the most likely mechanisms being the ingress of interstitials from the surface. Fluorine ion implantation has been shown to improve the oxidation resistance of gamma alloys, and ideally it could also improve the environmental embrittlement of high Nb content TiAl alloys. The effect of F ion implantation on the surface oxidation and embrittlement of a third generation, high Nb content TiAl alloy (Ti-45Al-5Nb-B-C) were investigated. Additionally, the ballistic impact resistance of a variety of gamma alloys, including Ti-48Al-2Cr- 2Nb, Ti-47Al-2Cr-2Nb, ABB-2, ABB-23, NCG359E, 95A and Ti-45Al-5Nb-B-C was accessed. Differences in the ballistic impact properties of the various alloys will be discussed, particularly with respect to their manufacturing process, microstructure, and tensile properties.

  20. Diana Al-Hadid: Identity and Heritage

    ERIC Educational Resources Information Center

    Jungerberg, Tom; Smith, Anna; Borsh, Colleen

    2012-01-01

    Diana Al-Hadid's sculptures reflect the many locations, cultures, histories, and mythologies that have shaped her as an artist. In large-scale works which have the appearance of architectural ruins, Al-Hadid employs imagery drawn from many diverse interests including science and technology, history, and literature. She also incorporates images and…

  1. 75 FR 62858 - United States, et al.

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-10-13

    ... Antitrust Division United States, et al. v. American Express Company, et al.; Proposed Final Judgment and... been filed with the United States District Court for the Eastern District of New York in United States..., 2010, the United States and seven States filed a Complaint alleging that certain rules, policies,...

  2. Energetics of Al13 Keggin cluster compounds

    PubMed Central

    Armstrong, Christopher R.; Casey, William H.; Navrotsky, Alexandra

    2011-01-01

    The ϵ-Al13 Keggin aluminum hydroxide clusters are essential models in establishing molecular pathways for geochemical reactions. Enthalpies of formation are reported for two salts of aluminum centered ϵ-Keggin clusters, Al13 selenate, (Na(AlO4)Al12(OH)24(SeO4)4•12H2O) and Al13 sulfate, (NaAlO4Al12(OH)24(SO4)4•12H2O). The measured enthalpies of solution, ΔHsol, at 28 °C in 5 N HCl for the ε-Al13 selenate and sulfate are −924.57 (± 3.83) and −944.30 ( ± 5.66) kJ·mol-1, respectively. The enthalpies of formation from the elements, ΔHf,el, for Al13 selenate and sulfate are −19,656.35 ( ± 67.30) kJ·mol-1, and −20,892.39 ( ± 70.01) kJ·mol-1, respectively. In addition, ΔHf,el for sodium selenate decahydrate was calculated using data from high temperature oxide melt solution calorimetry measurements: −4,006.39 ( ± 11.91) kJ·mol-1. The formation of both ε-Al13 Keggin cluster compounds is exothermic from oxide-based components but energetically unfavorable with respect to a gibbsite-based assemblage. To understand the relative affinity of the ϵ-Keggin clusters for selenate and sulfate, the enthalpy associated with two S-Se exchange reactions was calculated. In the solid state, selenium is favored in the Al13 compound relative to the binary chalcogenate, while in 5 N HCl, sulfur is energetically favored in the cluster compound compared to the aqueous solution. This contribution represents the first thermodynamic study of ε-Al13 cluster compounds and establishes a method for other such molecules, including the substituted versions that have been created for kinetic studies. Underscoring the importance of ε-Al13 clusters in natural and anthropogenic systems, these data provide conclusive thermodynamic evidence that the Al13 Keggin cluster is a crucial intermediate species in the formation pathway from aqueous aluminum monomers to aluminum hydroxide precipitates. PMID:21852572

  3. High temperature creep behaviour of Al-rich Ti-Al alloys

    NASA Astrophysics Data System (ADS)

    Sturm, D.; Heilmaier, M.; Saage, H.; Aguilar, J.; Schmitz, G. J.; Drevermann, A.; Palm, M.; Stein, F.; Engberding, N.; Kelm, K.; Irsen, S.

    2010-07-01

    Compared to Ti-rich γ-TiAl-based alloys Al-rich Ti-Al alloys offer an additional reduction of in density and a better oxidation resistance which are both due to the increased Al content. Polycrystalline material was manufactured by centrifugal casting. Microstructural characterization was carried out employing light-optical, scanning and transmission electron microscopy and XRD analyses. The high temperature creep of two binary alloys, namely Al60Ti40 and Al62Ti38 was comparatively assessed with compression tests at constant true stress in a temperature range between 1173 and 1323 K in air. The alloys were tested in the cast condition (containing various amounts of the metastable phases Al5Ti3 and h-Al2Ti) and after annealing at 1223 K for 200 h which produced (thermodynamically stable) lamellar γ-TiAl + r-Al2Ti microstructures. In general, already the as-cast alloys exhibit a reasonable creep resistance at 1173 K. Compared with Al60Ti40, both, the as-cast and the annealed Al62Ti38 alloy exhibit better creep resistance up to 1323 K which can be rationalized by the reduced lamella spacing. The assessment of creep tests conducted at identical stress levels and varying temperatures yielded apparent activation energies for creep of Q = 430 kJ/mol for the annealed Al60Ti40 alloy and of Q = 383 kJ/mol for the annealed Al62Ti38 material. The latter coincides well with that of Al diffusion in γ-TiAl, whereas the former can be rationalized by the instability of the microstructure containing metastable phases.

  4. Characteristics of heat resistant alloys Ti10Nb45Al and Ti18Nb48Al

    SciTech Connect

    Weijun Zhang; Guoliang Chen; Yandong Wang; Zuqing Sun )

    1993-05-01

    Based on a systematic study of the ternary Ti-Nb-Al system, two attractive heat resistant alloys, Ti10Nb45Al and Ti18Nb48Al, were developed, and the characteristics of these alloys were discussed: (1) After annealing at 1,200 C for 240 h and furnace cooling to room temperature, the Ti10Nb45Al alloy exhibits an [alpha][sub 2] + [gamma] lamellar microstructure, and the Ti18Nb48Al alloy shows a plate-like structure consisting of [alpha][sub 2], [gamma] and [gamma][sub 1] phases. (2) The specific strengths of Ti10Nb45Al and Ti18Nb48Al are much higher than TiAl and superalloys in the temperature range of 800 [approximately] 1,100 C. The compressive yield strengths of these alloys are on the order of 700 MPa at 800 C and 350 MPa at 1,100 C. The density of these alloys is about 4.3 g/cm[sup 3]. (3) The annealed Ti10Nb45Al and Ti18Nb48Al exhibit some ductility at room temperature, with the compressive elongation on the order of 12% and the fracture toughness as high as 16 MPa[radical]m. The ductile-brittle transformation temperatures for Ti10Nb45Al and Ti18Nb48Al are 650 C and 750 C, respectively. (4) The parabolic constant K[sub p] for oxidation of Ti10Nb45Al and Ti18Nb48Al are 0.88 and 0.29 mg[sup 2]cm[sup [minus]4]h[sup [minus]1] respectively, which are two orders of magnitude lower than that of TiAl and Ti[sub 3]Al alloys.

  5. Nucleation and Precipitation Strengthening in Dilute Al-Ti and Al-Zr Alloys

    NASA Astrophysics Data System (ADS)

    Knipling, Keith E.; Dunand, David C.; Seidman, David N.

    2007-10-01

    Two conventionally solidified Al-0.2Ti alloys (with 0.18 and 0.22 at. pct Ti) exhibit no hardening after aging up to 3200 hours at 375 °C or 425 °C. This is due to the absence of Al3Ti precipitation, as confirmed by electron microscopy and electrical conductivity measurements. By contrast, an Al-0.2Zr alloy (with 0.19 at. pct Zr) displays strong age hardening at both temperatures due to precipitation of Al3Zr (L12) within Zr-enriched dendritic regions. This discrepancy between the two alloys is explained within the context of the equilibrium phase diagrams: (1) the disparity in solid and liquid solubilities of Ti in α-Al is much greater than that of Zr in α-Al; and (2) the relatively small liquid solubility of Ti in α-Al limits the amount of solute retained in solid solution during solidification, while the comparatively high solid solubility reduces the supersaturation effecting precipitation during post-solidification aging. The lattice parameter mismatch of Al3Ti (L12) with α-Al is also larger than that of Al3Zr (L12), further hindering nucleation of Al3Ti. Classical nucleation theory indicates that the minimum solute supersaturation required to overcome the elastic strain energy of Al3Ti nuclei cannot be obtained during conventional solidification of Al-Ti alloys (unlike for Al-Zr alloys), thus explaining the absence of Al3Ti precipitation and the presence of Al3Zr precipitation.

  6. Corrosion Studies of 2195 Al-Li Alloy and 2219 Al Alloy with Differing Surface Treatments

    NASA Technical Reports Server (NTRS)

    Danford, M. D.; Mendrek, M. J.

    1998-01-01

    Corrosion studies of 2195 Al-Li and 2219 Al alloys have been conducted using the scanning reference electrode technique (SRET) and the polarization resistance (PR) technique. The SRET was used to study corrosion mechanisms, while corrosion rate measurements were studied with the PR technique. Plates of Al203 blasted, soda blasted and conversion coated 2219 Al were coated with Deft primer and the corrosion rates studied with the EIS technique. Results from all of these studies are presented.

  7. Opportunities for improving therapy development in ALS.

    PubMed

    Bruijn, Lucie; Cudkowicz, Merit

    2014-06-01

    In May 2013, The ALS Association and The Northeast ALS Consortium (NEALS) convened a meeting of stakeholders for a round-table discussion of ways to improve therapy development in ALS. The following overview summarizes issues raised and potential new directions discussed at the meeting. We recommend that future phase II clinical trials in ALS proceed when the proposed treatment is directed at targets that are likely to be involved in ALS pathogenesis in a defined subgroup of patients, and be accompanied by one or more biomarkers to track both clinical progression and pharmacodynamic engagement of the target. Innovations in trial structure and design, and greater involvement of patient advocates, may also improve trials. PMID:24472060

  8. NiAl alloys for structural uses

    NASA Technical Reports Server (NTRS)

    Koss, D. A.

    1991-01-01

    Alloys based on the intermetallic compound NiAl are of technological interest as high temperature structural alloys. These alloys possess a relatively low density, high melting temperature, good thermal conductivity, and (usually) good oxidation resistance. However, NiAl and NiAl-base alloys suffer from poor fracture resistance at low temperatures as well as inadequate creep strength at elevated temperatures. This research program explored macroalloying additions to NiAl-base alloys in order to identify possible alloying and processing routes which promote both low temperature fracture toughness and high temperature strength. Initial results from the study examined the additions of Fe, Co, and Hf on the microstructure, deformation, and fracture resistance of NiAl-based alloys. Of significance were the observations that the presence of the gamma-prime phase, based on Ni3Al, could enhance the fracture resistance if the gamma-prime were present as a continuous grain boundary film or 'necklace'; and the Ni-35Al-20Fe alloy was ductile in ribbon form despite a microstructure consisting solely of the B2 beta phase based on NiAl. The ductility inherent in the Ni-35Al-20Fe alloy was explored further in subsequent studies. Those results confirm the presence of ductility in the Ni-35Al-20Fe alloy after rapid cooling from 750 - 1000 C. However exposure at 550 C caused embrittlement; this was associated with an age-hardening reaction caused by the formation of Fe-rich precipitates. In contrast, to the Ni-35Al-20Fe alloy, exploratory research indicated that compositions in the range of Ni-35Al-12Fe retain the ordered B2 structure of NiAl, are ductile, and do not age-harden or embrittle after thermal exposure. Thus, our recent efforts have focused on the behavior of the Ni-35Al-12Fe alloy. A second parallel effort initiated in this program was to use an alternate processing technique, mechanical alloying, to improve the properties of NiAl-alloys. Mechanical alloying in the

  9. Al-Akhawayni's description of pulmonary circulation.

    PubMed

    Yarmohammadi, Hassan; Dalfardi, Behnam; Rezaian, Jafar; Ghanizadeh, Ahmad

    2013-10-01

    Since antiquity, heart function and the mechanism of blood circulation within the human body have been the focus of attention of scientists from different parts of the world. Over the passage of time, the theories and works of these scientists have resulted in the achievement of today's knowledge of circulation. The medieval Persian scholar, Al-Akhawayni Bukhari (?-983AD), is among the physicians who investigated both the anatomy and the physiology of the human body. Al-Akhawayni describes the mechanism of pulmonary circulation in his only extant book, "Hidayat al-Muta`llemin fi al-Tibb" (A Scholar's Guide to Medicine) with which he made a contribution to the development of knowledge regarding this mechanism in the medicine of the Islamic world. In this paper, Al-Akhawayni's viewpoints on anatomy and the function of the heart, its related vessels, and also pulmonary circulation will be briefly discussed. PMID:23890868

  10. AL(0) in municipal waste incinerator ash

    NASA Astrophysics Data System (ADS)

    Stipp, S. L.; Ronsbo, J. G.; Zunic, T. B.; Christensen, T. H.

    2003-04-01

    Disposal of municipal waste is a challenge to society. Waste volume is substantially decreased by incineration but residual ash usually contains a number of toxic components which must be immobilised to insure environmental protection. One element, chromium, is mobile and toxic in its oxidised state as Cr(VI) but it can be reduced to Cr(III) and immobilised. Reduction can be promoted by ash treatment with Fe(0) or Fe(II), but recent evidence shows that at least some Cr(VI) is reduced spontaneously in the ash. Aspects of ash behaviour suggest metallic aluminium as the reducing agent, but no direct evidence of Al(0) has been found until now. We examined filter ash from an energy-producing, municipal-waste incinerator (Vest-forbrænding) near Copenhagen. X-ray diffraction (XRD) identified expected salts of Na, K and Ca such as halite, sylvite, calcite, anhydrite and gypsum as well as quartz, feldspar and some hematite. Wave-dispersive electron microprobe produced elemen-tal maps of the ash; Al-rich areas were analysed quantitatively by comparison with standards. We identified metallic Al particles, averaging 50 to 100 micrometers in di-ameter, often with a fractured, glassy border of aluminum oxide. The particles were porous, explaining fast Cr(VI) reduction and they contained thin exsolution lamellae of Al-alloys of Pb and Cu or Mn, Fe and Ag, which provide clues of the Al(0) origin in the waste. Sometimes Al(0) occurred inside glassy globes of Al2O3. Time-of-flight secondary ion mass spectroscopy (TOF-SIMS) and X-ray photoelectron spectroscopy (XPS) proved that surface Al concentrations on ash particles were below detection, confirming reactivity of the Al(0) bulk. The persistence of reduced Al through the highly oxidising combustion procedure comes as a surprise and is a benefit in the immobilisation of Cr(VI) from municipal-waste incineration residues.

  11. Japanese version of the ALS-FTD-Questionnaire (ALS-FTD-Q-J).

    PubMed

    Watanabe, Yasuhiro; Beeldman, Emma; Raaphorst, Joost; Izumi, Yuishin; Yoshino, Hiide; Masuda, Michihito; Atsuta, Naoki; Ito, Satoru; Adachi, Tadashi; Adachi, Yoshiki; Yokota, Osamu; Oda, Masaya; Hanashima, Ritsuko; Ogino, Mieko; Ichikawa, Hiroo; Hasegawa, Kazuko; Kimura, Hideki; Shimizu, Toshio; Aiba, Ikuko; Yabe, Hayato; Kanba, Makoto; Kusumi, Kimiyoshi; Aoki, Tetsuya; Hiroe, Yu; Watanabe, Hirohisa; Nishiyama, Kazutoshi; Nomoto, Masahiro; Sobue, Gen; Nakashima, Kenji

    2016-08-15

    Amyotrophic lateral sclerosis (ALS) and frontotemporal dementia (FTD) share common clinical, genetic and neuropathological features. Some ALS patients have behavioral/personality changes, which could result in significant obstacles in the care provided by family members and caregivers. An easy screening tool would contribute greatly to the evaluation of these symptoms. We translated the ALS-FTD-Questionnaire, developed in the Netherlands, into Japanese (ALS-FTD-Q-J) and examined the clinimetric properties (internal consistency, construct and clinical validity). Patients with ALS and/or behavioral variant FTD (bvFTD) were evaluated alongside healthy controls in this multicenter study. All ALS patients, regardless of bvFTD status, were further evaluated by the frontal behavioral inventory (FBI) and for frontal/executive function, cognition, anxiety/depression, and motor functions. Data from 146 subjects were analyzed: ALS (92), ALS-bvFTD (6), bvFTD (16), and healthy controls (32). The internal consistency of the ALS-FTD-Q-J was good (Cronbach α=0.92). The ALS-FTD-Q-J showed construct validity as it exhibited a high correlation with the FBI (r=0.79). However, correlations were moderate with anxiety/depression and low with cognitive scales, in contrast to the original report, i.e. a moderate correlation with cognition and a low correlation with anxiety/depression. The ALS-FTD-Q-J discriminated ALS patients from (ALS-)bvFTD patients and controls. Thus, the ALS-FTD-Q-J is useful for evaluating Japanese ALS/FTD patients. PMID:27423564

  12. Effects of hydrogen absorption in TbNiAl and UNiAl

    SciTech Connect

    Bordallo, H.N.; Nakotte, H.; Schultz, A.; Kolomiets, A.V.; Havela, L.; Andreev, A.V.

    1998-12-31

    Although hydrides of intermetallic compounds are used extensively as hydrogen-storage media, little is known about the exact nature of metal-hydrogen interactions. However, this knowledge is of essential importance for the understanding of thermodynamics and other properties. Hydrides (deuterides) of TbNiAl and UNiAl have been widely studied because of drastic increase of magnetic ordering temperature under hydrogenation. Here the authors report neutron-diffraction results of the three deuterides, TbNiAlD{sub 1.28}, TbNiAlD{sub 0.8}a nd UNiAlD{sub 2.23}.

  13. Atomistic Modeling of RuAl and (RuNi) Al Alloys

    NASA Technical Reports Server (NTRS)

    Gargano, Pablo; Mosca, Hugo; Bozzolo, Guillermo; Noebe, Ronald D.; Gray, Hugh R. (Technical Monitor)

    2002-01-01

    Atomistic modeling of RuAl and RuAlNi alloys, using the BFS (Bozzolo-Ferrante-Smith) method for alloys is performed. The lattice parameter and energy of formation of B2 RuAl as a function of stoichiometry and the lattice parameter of (Ru(sub 50-x)Ni(sub x)Al(sub 50)) alloys as a function of Ni concentration are computed. BFS based Monte Carlo simulations indicate that compositions close to Ru25Ni25Al50 are single phase with no obvious evidence of a miscibility gap and separation of the individual B2 phases.

  14. A new discontinuously reinforced aluminum MMC: Al+AlB{sub 2} flakes

    SciTech Connect

    HALL,AARON C.; ECONOMY,J.

    2000-06-08

    Development of a novel metal matrix composite based on the Al-B alloy system has been undertaken. Preparation of this discontinuously reinforced material is based on the precipitation of high aspect ratio AlB{sub 2} from an Al-B alloy. This paper describes a number of efforts forced on preparing high volume fractions (> 30 v%) of AlB{sub 2} in aluminum. New insights into the behavior of the Al-B alloys system allowed this effort to be successful.

  15. Electrical conductivity of Al-bearing bridgmanite

    NASA Astrophysics Data System (ADS)

    Yoshino, T.; Kamada, S.; Ohtani, E.; Hirao, N.

    2015-12-01

    Electrical conductivity measurements of bridgmanite with various Al contents and constant Mg# 90 at room temperature up to 2000 K and 26-28 GPa were performed in Kawai-type multianvil apparatus using impedance spectroscopic analyses. The incorporation of Al into bridgmanite significantly raises the electrical conductivity but it is small conductivity variation with respect to the amount of Al. Synchrotron Mössbauer spectroscopy of recovered samples showed a significant amount of ferric iron in aluminous bridgmanite. The mobility of charge carriers in bridgmanite was calculated from the conductivity and Fe3+/ΣFe. A relation between the logarithm of electrical conductivity and reciprocal temperature is consistent with Fe2+-Fe3+ electron hopping (small polaron) as the dominant conduction mechanism at low temperatures (< 1400 K) and ionic conduction at high temperatures (> 1600 K). Taking various conduction mechanisms into account, we develop an electrical conductivity model for aluminous bridgmanite as a function of Al and Fe content. This conductivity model suggests that the electrical conductivity of aluminous bridgmanite has a maximum at around 0.13 Al per formula unit, and further increase of Al in bridgmanite reduces the conductivity. The conductivity increase observed in the uppermost lower mantle by electromagnetic studies can be explained by increases of Fe and Na content in combination with substitution of Al into bridgmanite with increasing pressure due to the gradual decomposition of majorite garnet.

  16. Orthorhombic aluminium oxyfluoride, AlOF.

    PubMed

    Vasiliev, Alexander D; Melnikova, Svetlana V; Isaenko, Lyudmila I

    2009-04-01

    Crystals of the title compound were extracted from the bulk of grown SrAlF(5) crystals as unexpected inclusions that were identified as the long sought after aluminium oxyfluoride. The structure of AlOF is built up from tetrahedral and octahedral polyhedra. Each tetrahedron is bisected by a mirror plane, with the Al atom and two vertex anions in the plane. All tetrahedral vertices are positions of competing oxide and fluoride ions and are shared with octahedra. These shared vertices belong to two octahedral edges which join the octahedra to form infinite zigzag chains. The chains are strung along twofold screw axes that run parallel to the unit-cell b axis. The remaining two octahedral vertices are occupied only by fluoride ions. A small deficiency in the occupation of the octahedral Al position was suggested by the refinement. However, the stoichiometry of the compound is AlOF within experimental uncertainty. The Al-F(O) distances are separated into three groups with average values of 1.652 (3) (tetrahedra), 1.800 (2) (octahedra) and 1.894 (2) A (octahedra). This structure differs widely from the reported tetragonal phase Al(1-x)O(1-3x)F(1+3x) (x = 0.0886) [Kutoglu (1992). Z. Kristallogr. 199, 197-201], which consists solely of octahedral structural units. PMID:19346595

  17. Comparative study on interface and bulk charges in AlGaN/GaN metal-insulator-semiconductor heterostructures with Al2O3, AlN, and Al2O3/AlN laminated dielectrics

    NASA Astrophysics Data System (ADS)

    Zhu, Jie-Jie; Ma, Xiao-Hua; Chen, Wei-Wei; Hou, Bin; Xie, Yong; Hao, Yue

    2016-05-01

    In this paper, the interface and bulk charges in AlGaN/GaN metal-insulator-semiconductor (MIS) heterostructures with AlN, Al2O3, and Al2O3/AlN laminated dielectrics were studied. In situ plasma pretreatment resulted negligible interface trap states and voltage hysteresis. The fixed charge density at Al2O3/AlN (or Al2O3/barrier) interface was estimated to be 1.66 × 1013 cm-2 by using flat-band voltage shift, and the oxide bulk charge concentration was 2.86 × 1017 cm-3. The interface charge density at other interfaces were at the order of 1011 cm-2. Simulation results using the above charge density/concentration indicated that Al2O3/AlN interface fixed charges dominated the dielectric-related voltage shift in AlGaN/GaN MIS heterostructures, which caused a large voltage shift of -3 V with 10 nm Al2O3 thickness, while the flat-band voltage variety resulting from other types of charges was within 0.1 V.

  18. Hybrid Al + Al3Ni metallic foams synthesized in situ via laser engineered net shaping

    NASA Astrophysics Data System (ADS)

    Zheng, Baolong; Li, Ying; Smugeresky, John E.; Zhou, Yizhang; Baker, Dean; Lavernia, Enrique J.

    2011-09-01

    A hybrid, Al + Al3Ni metallic foam was synthesized in situ via laser engineered net shaping (LENS®) of Ni-coated 6061 Al powder in the absence of a foaming agent. During LENS® processing, the Ni coating reacted with the Al matrix, resulting in the simultaneous formation of a fine dispersion of Al3Ni, and a high volume fraction of porosity. As a reinforcement phase, the intermetallic compound formed particles with a size range of 1-5 µm and a volume fraction of 63%, with accompanying 35-300 µm pores with a 60% volume fraction. The microstructure of the as-deposited Al + Al3Ni composite foams was characterized using SEM, EDS, XRD and TEM/HRTEM techniques. The evolution of the microstructure was analyzed on the basis of the thermal field present during deposition, paying particular attention to the thermodynamics of the Al3Ni intermetallic compound formation as well as discussing the mechanisms that may be responsible for the observed porosity. The mechanical behavior of the as-deposited material was characterized using compression and microhardness testing, indicating that the yield strength and hardness are 190 MPa and 320 HV, respectively, which represents an increase of over three times higher than that of annealed Al6061, or similar to heat-treated Al6061 fully dense matrix, and much higher than those of traditional Al alloy foams, and with a low density of 1.64 g/m3.

  19. Arsenate uptake by Al nanoclusters and other Al-based sorbents during water treatment.

    PubMed

    Mertens, Jasmin; Rose, Jérôme; Wehrli, Bernhard; Furrer, Gerhard

    2016-01-01

    In many parts of the world, arsenic from geogenic and anthropogenic sources deteriorates the quality of drinking water resources. Effective methods of arsenic removal include adsorption and coagulation with iron- and aluminum-based materials, of which polyaluminum chloride is widely employed as coagulant in water treatment due to its low cost and high efficiency. We compared the arsenic uptake capacity and the arsenic bonding sites of different Al-based sorbents, including Al nanoclusters, polyaluminum chloride, polyaluminum granulate, and gibbsite. Extended X-ray absorption fine structure (EXAFS) spectroscopy revealed that As(V) forms bidentate-binuclear complexes in interaction with all Al-based removal agents. The octahedral configuration of nanoclusters and the distribution of sorption sites remain the same in all types of removal agents consisting of nano-scale Al oxyhydroxide particles. The obtained distances for As(V)-O and As(V)-Al agreed with previously published data and were found to be 1.69 ± 0.02 Å and 3.17-3.21 Å, respectively. Our study suggests that As(V) binds to Al nanoclusters as strongly as to Al oxide surfaces. The As sorption capacity of Al nanoclusters was found to be very similar to that of Al clusters in a polyaluminum chloride. The most efficient Al-based sorbents for arsenic removal were Al nanoclusters, followed by polyaluminum granulate. PMID:26613179

  20. Oxidation of Al2O3 continuous fiber-reinforced/NiAl composites

    NASA Technical Reports Server (NTRS)

    Doychak, J.; Nesbitt, J. A.; Noebe, R. D.; Bowman, R. R.

    1992-01-01

    The 1200 C and 1300 C isothermal and cyclic oxidation behavior of Al2O3 continuous fiber-reinforced/NiAl composites were studied. Oxidation resulted in formation of Al2O3 external scales in a similar manner as scales formed on monolithic NiAl. The isothermal oxidation of an Al2O3/NiAl composite resulted in oxidation of the matrix along the fiber/matrix interface near the fiber ends. This oxide acted as a wedge between the fiber and the matrix, and, under cyclic oxidation conditions, led to further oxidation along the fiber lengths and eventual cracking of the composite. The oxidation behavior of composites in which the Al2O3 fibers were sputter coated with nickel prior to processing was much more severe. This was attributed to open channels around the fibers which formed during processing, most likely as a result of the diffusion of the nickel coating into the matrix.

  1. High performance AlGaN/GaN HEMTs with AlN/SiNx passivation

    NASA Astrophysics Data System (ADS)

    Xin, Tan; Yuanjie, Lü; Guodong, Gu; Li, Wang; Shaobo, Dun; Xubo, Song; Hongyu, Guo; Jiayun, Yin; Shujun, Cai; Zhihong, Feng

    2015-07-01

    AlGaN/GaN high electron-mobility transistors (HEMTs) with 5 nm AlN passivation by plasma enhanced atomic layer deposition (PEALD) were fabricated, covered by 50 nm SiNx which was grown by plasma enhanced chemical vapor deposition (PECVD). With PEALD AlN passivation, current collapse was suppressed more effectively and the devices show better subthreshold characteristics. Moreover, the insertion of AlN increased the RF transconductance, which lead to a higher cut-off frequency. Temperature dependence of DC characteristics demonstrated that the degradations of drain current and maximum transconductance at elevated temperatures for the AlN/SiNx passivated devices were much smaller compared with the devices with SiNx passivation, indicating that PEALD AlN passivation can improve the high temperature operation of the AlGaN/GaN HEMTs. Project supported by the National Natural Science Foundation of China (No. 60890192).

  2. Optical characterization of Al- and N-polar AlN waveguides for integrated optics

    NASA Astrophysics Data System (ADS)

    Rigler, Martin; Buh, Jože; Hoffmann, Marc P.; Kirste, Ronny; Bobea, Milena; Mita, Seiji; Gerhold, Michael D.; Collazo, Ramon; Sitar, Zlatko; Zgonik, Marko

    2015-04-01

    Dispersion of the extraordinary and ordinary refractive indices of Al- and N-polar AlN waveguides is measured by multiple angle-of-incidence and spectroscopic ellipsometry techniques. The polarity-controlled AlN layers are grown by metal-organic chemical vapor deposition on (0001)-sapphire substrates. Taking into consideration the different surface morphologies of the Al- and N-polar AlN waveguides, we propose two optical models to describe the measured ellipsometry data. The results indicate that there is no difference between the refractive indices of the AlN grown in opposite directions, which confirms the potential of the AlN lateral polar structures for use in nonlinear optical applications based on quasi phase matching.

  3. A Rechargeable Al/S Battery with an Ionic-Liquid Electrolyte.

    PubMed

    Gao, Tao; Li, Xiaogang; Wang, Xiwen; Hu, Junkai; Han, Fudong; Fan, Xiulin; Suo, Liumin; Pearse, Alex J; Lee, Sang Bok; Rubloff, Gary W; Gaskell, Karen J; Noked, Malachi; Wang, Chunsheng

    2016-08-16

    Aluminum metal is a promising anode material for next generation rechargeable batteries owing to its abundance, potentially dendrite-free deposition, and high capacity. The rechargeable aluminum/sulfur (Al/S) battery is of great interest owing to its high energy density (1340 Wh kg(-1) ) and low cost. However, Al/S chemistry suffers poor reversibility owing to the difficulty of oxidizing AlSx . Herein, we demonstrate the first reversible Al/S battery in ionic-liquid electrolyte with an activated carbon cloth/sulfur composite cathode. Electrochemical, spectroscopic, and microscopic results suggest that sulfur undergoes a solid-state conversion reaction in the electrolyte. Kinetics analysis identifies that the slow solid-state sulfur conversion reaction causes large voltage hysteresis and limits the energy efficiency of the system. PMID:27417442

  4. Suspected variables among Al Sufi stars.

    NASA Astrophysics Data System (ADS)

    Hoffleit, D.

    In the tenth century Al Sufi compiled a catalogue of some 1100 stars. J.E. Gore, around 1900, wrote extensively on the magnitudes of these stars. On intercomparing them with a few other catalogues, Gore surmised that some 38 stars appeared to show secular variations. Here all the Al Sufi magnitudes have been compared with numerous additional sources, but smooth secular variations are not substantiated although some stars seem to have undergone comparatively sudden changes after about 1600. About 70 Al Sufi stars are now named or suscpected variable stars, but nearly all with amplitudes under 0.3 V.

  5. Ni{sub 3}Al aluminide alloys

    SciTech Connect

    Liu, C.T.

    1993-10-01

    This paper provides a brief review of the recent progress in research and development of Ni{sub 3}Al and its alloys. Emphasis has been placed on understanding low ductility and brittle fracture of Ni{sub 3}Al alloys at ambient and elevated temperatures. Recent studies have resulted in identifying both intrinsic and extrinsic factors governing the fracture behavior of Ni{sub 3}Al alloys. Parallel efforts on alloy design using physical metallurgy principles have led to properties for structural use. Industrial interest in these alloys is high, and examples of industrial involvement in processing and utilization of these alloys are briefly mentioned.

  6. Characterization of AlInN/AlN/GaN Heterostructures with Different AlN Buffer Thickness

    NASA Astrophysics Data System (ADS)

    Çörekçi, S.; Dugan, S.; Öztürk, M. K.; Çetin, S. Ş.; Çakmak, M.; Özçelik, S.; Özbay, E.

    2016-05-01

    Two AlInN/AlN/GaN heterostructures with 280-nm- and 400-nm-thick AlN buffer grown on sapphire substrates by metal-organic chemical vapor deposition (MOCVD) have been investigated by x-ray diffraction (XRD), atomic force microscopy (AFM), photoluminescence (PL) and Hall-effect measurements. The symmetric (0002) plane with respect to the asymmetric (10bar{1} 2) plane in the 280-nm-thick AlN buffer has a higher crystal quality, as opposed to the 400-nm-thick buffer. The thinner buffer improves the crystallinity of both (0002) and (10bar{1} 2) planes in the GaN layers, it also provides a sizeable reduction in dislocation density of GaN. Furthermore, the lower buffer thickness leads to a good quality surface with an rms roughness of 0.30 nm and a dark spot density of 4.0 × 108 cm-2. The optical and transport properties of the AlInN/AlN/GaN structure with the relatively thin buffer are compatible with the enhancement in its structural quality, as verified by XRD and AFM results.

  7. Characterization of AlInN/AlN/GaN Heterostructures with Different AlN Buffer Thickness

    NASA Astrophysics Data System (ADS)

    Çörekçi, S.; Dugan, S.; Öztürk, M. K.; Çetin, S. Ş.; Çakmak, M.; Özçelik, S.; Özbay, E.

    2016-07-01

    Two AlInN/AlN/GaN heterostructures with 280-nm- and 400-nm-thick AlN buffer grown on sapphire substrates by metal-organic chemical vapor deposition (MOCVD) have been investigated by x-ray diffraction (XRD), atomic force microscopy (AFM), photoluminescence (PL) and Hall-effect measurements. The symmetric (0002) plane with respect to the asymmetric (10bar{1}2) plane in the 280-nm-thick AlN buffer has a higher crystal quality, as opposed to the 400-nm-thick buffer. The thinner buffer improves the crystallinity of both (0002) and (10bar{1}2) planes in the GaN layers, it also provides a sizeable reduction in dislocation density of GaN. Furthermore, the lower buffer thickness leads to a good quality surface with an rms roughness of 0.30 nm and a dark spot density of 4.0 × 108 cm-2. The optical and transport properties of the AlInN/AlN/GaN structure with the relatively thin buffer are compatible with the enhancement in its structural quality, as verified by XRD and AFM results.

  8. Diffusion at the Al/Al oxide interface during electromigration in wide lines

    NASA Astrophysics Data System (ADS)

    Augur, R. A.; Wolters, R. A. M.; Schmidt, W.; Dirks, A. G.; Kordić, S.

    1996-03-01

    Significant large-scale modification of the surface of Al-Si conductors was observed, due to electromigration in wide lines and under low stress conditions. After electromigration stressing the Al layers showed local thickness variations, i.e., damage by thinning. The mechanism underlying this damage causes substantial metal transport. Nevertheless, damage by thinning has received little attention in the past. Thinning was observed: (1) in a number of different alloys (Al-Si, Al-Cu, Al-Si-V, and Al-Si-V-Pd), (2) with a number of different underlayers [SiO2, W-Ti (no vacuum break after Al deposition) and W-Ti (oxidized surface before Al deposition)], (3) over an extended temperature range, (4) over a range of current density, and (5) in structures with and without passivation. The results show that thinning is a general phenomenon. An activation energy of approximately 0.5 eV was determined for the temperature dependence of a combined mechanism of concurrent thinning plus voiding in Al99Si1. Several alternatives are examined to explain the observations, namely mass movement along dislocations, Al bulk diffusion, and diffusion at the interface between the Al and its oxide. It is shown that diffusion at the Al/Al oxide interface most probably plays an important role in the damage mechanism, even under stress conditions where grain boundary diffusion is traditionally thought to dominate. Results also showed that alloying of Al with Pd can reduce the effects of damage by thinning.

  9. Electroforming and Ohmic contacts in Al-Al2O3-Ag diodes

    NASA Astrophysics Data System (ADS)

    Hickmott, T. W.

    2012-03-01

    Electroforming of metal-insulator-metal (MIM) diodes is a non-destructive dielectric breakdown process that changes the diode from its initial high resistance state (HRS) to a low resistance state (LRS). After electroforming, resistance switching memories (RSMs) use voltages to switch from HRS to LRS and back. Many MIM combinations are proposed for use in RSMs. In many cases conduction in the LRS is nearly temperature independent at low temperatures; an Ohmic contact with a barrier to electron injection of ˜0 eV results from electroforming. Electroforming of Al-Al2O3-Ag diodes with amorphous anodic Al2O3 thicknesses between 12 and 41 nm has been studied. Two anodizing electrolytes have been used; 0.1 M ammonium pentaborate (bor-H2O) and a solution of 0.1 M of ammonium pentaborate per liter of ethylene glycol (bor-gly). Polarization of Al2O3 and negative charge in Al2O3 are much larger when Al2O3 is formed in bor-H2O solution than when Al is anodized in bor-gly solution. Electroforming of Al-Al2O3-Ag diodes results in an Ohmic contact at the Al-Al2O3 interface, voltage-controlled negative resistance (VCNR) in the current-voltage (I-V) characteristics, electroluminescence (EL), and electron emission into vacuum (EM) from filamentary conducting channels. Two distinct modes of electroforming occur for Al-Al2O3-Ag diodes. α-forming occurs for 2.5 V ≲ VS ≲ 5 V, where VS is the applied voltage. It is characterized by an abrupt current jump with the simultaneous appearance of EL and EM. β-forming occurs for VS ≳ 7 V. I-V curves, EL, and EM develop gradually and are smaller than for α-forming. Electroforming occurs more readily for diodes with Al2O3 formed in bor-H2O that have greater defect densities. Fully developed I-V curves have similar VCNR, EL, and EM after α-forming or β-forming. A model is proposed in which excited states of F-centers, oxygen vacancies in amorphous anodic Al2O3, form defect conduction bands. Electroforming that results in an Ohmic

  10. ALS: Recent Developments from Genetics Studies.

    PubMed

    Therrien, Martine; Dion, Patrick A; Rouleau, Guy A

    2016-06-01

    Amyotrophic lateral sclerosis (ALS) is a fatal disorder that is characterized by a progressive degeneration of the upper and lower motor neurons. Most cases appear to be sporadic, but 5-10 % of cases have a family history of the disease. High-throughput DNA sequencing and related genomic capture tools are methodological advances which have rapidly contributed to an acceleration in the discovery of genetic risk factors for both familial and sporadic ALS. It is interesting to note that as the number of ALS genes grows, many of the proteins they encode are in shared intracellular processes. This review will summarize some of the recent advances and gene discovery made in ALS. PMID:27113253

  11. Pesticides Linked to Raised Risk of ALS

    MedlinePlus

    ... nlm.nih.gov/medlineplus/news/fullstory_158737.html Pesticides Linked to Raised Risk of ALS One toxin ... MONDAY, May 9, 2016 (HealthDay News) -- Exposure to pesticides and other chemicals may increase the risk for ...

  12. Stem Cells Deemed Safe for ALS Patients

    MedlinePlus

    ... nlm.nih.gov/medlineplus/news/fullstory_159627.html Stem Cells Deemed Safe for ALS Patients But further ... June 29, 2016 (HealthDay News) -- Scientists report that stem cell therapy appears to be safe for people ...

  13. ALS and Oxidative Stress: The Neurovascular Scenario

    PubMed Central

    Thakur, Keshav; Gupta, Pawan Kumar

    2013-01-01

    Oxidative stress and angiogenic factors have been placed as the prime focus of scientific investigations after an establishment of link between vascular endothelial growth factor promoter (VEGF), hypoxia, and amyotrophic lateral sclerosis (ALS) pathogenesis. Deletion of the hypoxia-response element in the vascular endothelial growth factor promoter and mutant superoxide dismutase 1 (SOD1) which are characterised by atrophy and muscle weakness resulted in phenotype resembling human ALS in mice. This results in lower motor neurodegeneration thus establishing an important link between motor neuron degeneration, vasculature, and angiogenic molecules. In this review, we have presented human, animal, and in vitro studies which suggest that molecules like VEGF have a therapeutic, diagnostic, and prognostic potential in ALS. Involvement of vascular growth factors and hypoxia response elements also highlights the converging role of oxidative stress and neurovascular network for understanding and treatment of various neurodegenerative disorders like ALS. PMID:24367722

  14. Stem Cells Deemed Safe for ALS Patients

    MedlinePlus

    ... page: https://medlineplus.gov/news/fullstory_159627.html Stem Cells Deemed Safe for ALS Patients But further research ... June 29, 2016 (HealthDay News) -- Scientists report that stem cell therapy appears to be safe for people with ...

  15. Pesticides Linked to Raised Risk of ALS

    MedlinePlus

    ... page: https://medlineplus.gov/news/fullstory_158737.html Pesticides Linked to Raised Risk of ALS One toxin ... MONDAY, May 9, 2016 (HealthDay News) -- Exposure to pesticides and other chemicals may increase the risk for ...

  16. Thermal Conductivity of Al-Salt Composites

    NASA Astrophysics Data System (ADS)

    Li, Peng; Zhang, Mei; Wang, Lijun; Seetharaman, Seshadri

    2015-11-01

    With a view to examine the possibility of estimating the content of entrapped metallic aluminium in the salt cake from aluminium remelting, the thermal diffusivity of reference composites of KCl-NaCl-Al was measured as a function of aluminium metal content at room temperature. The thermal conductivity of the reference composites was found to increase with the metallic Al content. The lumped parameter model approach was carried out to discuss the influence of different geometry arrangements of each phase, viz. air, salts and metallic aluminium on the thermal conductivity. Application of the present results to industrial samples indicates that factors such as the interfacial condition of metallic Al particles have to be considered in order to estimate the amount of entrapped Al in the salt cake.

  17. Glial cells in ALS: the missing link?

    PubMed

    Raibon, Elsa; Todd, Lisa Marie; Möller, Thomas

    2008-08-01

    Amyotrophic lateral sclerosis (ALS) was initially known as Charcot's sclerosis, named after the French neurobiologist and physician Jean-Martin Charcot who first described this type of muscular atrophy in the early nineteenth century. In the United States, ALS became widely known as Lou Gehrig's disease after the famous baseball player who succumbed to the disease in the late 1930s. Currently, ALS is the most common motor neuron disease, with a worldwide incidence of 8 cases per 100,000 population per year. Familial forms constitute approximately 5% to 10% of all cases. Onset increases with age, with a peak in the seventh decade and a slight preponderance (relative risk, 1.3-1.5) among men compared with women. Rapid progression of motor neuron loss leads to death an average of 3 to 5 years after symptom onset. The cause of ALS remains unknown and there is still no curative therapy. PMID:18625409

  18. Itinerant antiferromagnetism of TiAl alloys

    NASA Astrophysics Data System (ADS)

    Petrişor, T.; Pop, I.; Giurgiu, A.; Farbaş, N.

    1986-06-01

    Magnetic susceptibility measurements of TiAl alloys are reported. Aluminium, by alloying, acts on the Néel temperature of pure titanium giving rise to a complicated phase diagram. A theoretical model, based on the itinerant antiferromagnetism model of chromium is proposed in order to explain the magnetic phase diagram of TiAl alloys. The experimental and theoretical magnetic phase diagram are in good agreement.

  19. Magnetism of Al-Mn quasicrystals

    SciTech Connect

    Liu, F.; Khanna, S.N.; Magaud, L.; Jena, P. ); de Coulon, V.; Reuse, F. ); Jaswal, S.S.; He, X. ); Cyrot-Lackman, F. )

    1993-07-01

    The effect of symmetry and concentration of Mn on the magnetism of Al-Mn quasicrystals has been investigated through self-consistent density-functional calculations using molecular clusters and supercell band-structure schemes. A single Mn atom surrounded by 54 Al atoms in an icosahedral or a cuboctahedral structure is found to be nonmagnetic. However, as the Mn concentration is increased, moments develop on Mn sites whose magnitude and coupling depend on their location.

  20. 17th Annual ALS Users' Association Meeting

    SciTech Connect

    Robinson, Art; Tamura, Lori

    2004-11-29

    It's not exactly Russian roulette, but scheduling October events outdoors is not risk-free, even in usually sunny California. An overflow crowd of more than 400 registered users, ALS staff, and vendors enjoyed a full indoor program featuring science highlights and workshops spread over two and a half days from October 18 to October 20. However, a major storm, heralding the onset of the San Francisco Bay Area rainy season, posed a few weather challenges for the events on the ALS patio.

  1. Next-generation sequencing of 28 ALS-related genes in a Japanese ALS cohort.

    PubMed

    Nakamura, Ryoichi; Sone, Jun; Atsuta, Naoki; Tohnai, Genki; Watanabe, Hazuki; Yokoi, Daichi; Nakatochi, Masahiro; Watanabe, Hirohisa; Ito, Mizuki; Senda, Jo; Katsuno, Masahisa; Tanaka, Fumiaki; Li, Yuanzhe; Izumi, Yuishin; Morita, Mitsuya; Taniguchi, Akira; Kano, Osamu; Oda, Masaya; Kuwabara, Satoshi; Abe, Koji; Aiba, Ikuko; Okamoto, Koichi; Mizoguchi, Kouichi; Hasegawa, Kazuko; Aoki, Masashi; Hattori, Nobutaka; Tsuji, Shoji; Nakashima, Kenji; Kaji, Ryuji; Sobue, Gen

    2016-03-01

    We investigated the frequency and contribution of variants of the 28 known amyotrophic lateral sclerosis (ALS)-related genes in Japanese ALS patients. We designed a multiplex, polymerase chain reaction-based primer panel to amplify the coding regions of the 28 ALS-related genes and sequenced DNA samples from 257 Japanese ALS patients using an Ion Torrent PGM sequencer. We also performed exome sequencing and identified variants of the 28 genes in an additional 251 ALS patients using an Illumina HiSeq 2000 platform. We identified the known ALS pathogenic variants and predicted the functional properties of novel nonsynonymous variants in silico. These variants were confirmed by Sanger sequencing. Known pathogenic variants were identified in 19 (48.7%) of the 39 familial ALS patients and 14 (3.0%) of the 469 sporadic ALS patients. Thirty-two sporadic ALS patients (6.8%) harbored 1 or 2 novel nonsynonymous variants of ALS-related genes that might be deleterious. This study reports the first extensive genetic screening of Japanese ALS patients. These findings are useful for developing genetic screening and counseling strategies for such patients. PMID:26742954

  2. Metastability in the MgAl2O4-Al2O3 System

    DOE PAGESBeta

    Wilkerson, Kelley R.; Smith, Jeffrey D.; Hemrick, James G.

    2014-07-22

    Aluminum oxide must take a spinel form ( γ-Al2O3) at elevated temperatures in order for extensive solid solution to form between MgAl2O4 and α-Al2O3. The solvus line between MgAl2O4 and Al2O3 has been defined at 79.6 wt% Al2O3 at 1500°C, 83.0 wt% Al2O3 at 1600°C, and 86.5 wt% Al2O3 at 1700°C. A metastable region has been defined at temperatures up to 1700°C which could have significant implications for material processing and properties. Additionally, initial processing could have major implications on final chemistry. The spinel solid solution region has been extended to form an infinite solid solution with Al2O3 at elevatedmore » temperatures. A minimum in melting at 1975°C and a chemistry of 96 wt% Al2O3 rather than a eutectic is present, resulting in no eutectic crystal formation during solidification.« less

  3. Excitotoxicity in ALS: Overstimulation, or overreaction?

    PubMed

    King, Anna E; Woodhouse, Adele; Kirkcaldie, Matthew T K; Vickers, James C

    2016-01-01

    Amyotrophic lateral sclerosis (ALS) is an adult onset neurodegenerative disease that results in motor dysfunction and death, generally from respiratory failure. 90% of ALS cases are sporadic with no known cause. Familial cases have been linked with mutations in several disparate classes of genes, including those involved in DNA/RNA metabolism, protein misfolding, oxidative stress and the cytoskeleton, leading to the proposition that ALS could be a multi-factorial disease. However, alterations in excitability have been reported in all types of ALS cases, and may be a common disease mechanism predisposing neurons to degeneration. Excitotoxicity has long been suspected as a mediator in the disease process, and may arise from changes in synaptic inputs, or alterations in the excitability of the neurons being stimulated. Although the glutamatergic system is widely recognised as a therapeutic avenue with the potential to extend lifespan and delay disease onset, the causes of altered excitability in ALS are currently unclear and warrant further investigation. This article reviews current evidence of alterations to excitatory and inhibitory signalling in the cortex and spinal cord, and in the intrinsic excitability of motor neurons, in ALS. PMID:26584004

  4. Clinical trials for neuroprotection in ALS.

    PubMed

    Siciliano, G; Carlesi, C; Pasquali, L; Piazza, S; Pietracupa, S; Fornai, F; Ruggieri, S; Murri, L

    2010-07-01

    Owing to uncertainty on the pathogenic mechanisms underlying motor neuron degeneration in amyotrophic lateral sclerosis (ALS) riluzole remains the only available therapy, with only marginal effects on disease survival. Here we review some of the recent advances in the search for disease-modifying drugs for ALS based on their putative neuroprotective effetcs. A number of more or less established agents have recently been investigated also in ALS for their potential role in neuroprotection and relying on antiglutamatergic, antioxidant or antiapoptotic strategies. Among them Talampanel, beta-lactam antibiotics, Coenzyme Q10, and minocycline have been investigated. Progress has also been made in exploiting growth factors for the treatment of ALS, partly due to advances in developing effective delivery systems to the central nervous system. A number of new therapies have also been identified, including a novel class of compounds, such as heat-shock protein co-inducers, which upregulate cell stress responses, and agents promoting autophagy and mitochondriogenesis, such as lithium and rapamycin. More recently, alterations of mRNA processing were described as a pathogenic mechanism in genetically defined forms of ALS, as those related to TDP-43 and FUS-TLS gene mutations. This knowledge is expected to improve our understanding of the pathogenetic mechanism in ALS and developing more effective therapies. PMID:20406180

  5. Modeling of precipitation in Al alloys

    SciTech Connect

    Asta, M.; Foiles, S.M.; Wolfer, W.G.

    1996-10-01

    Objective was the development of a computational model of precipitation from a supersaturated alloy solid solution. The model is based on the formalism of chemical-reaction-rate theory combined with classical descriptions of precipitate thermodynamic properties and a mean-field treatment of diffusion-limited growht and coarsening. For the case of precipitation of Al{sub 3}Sc in supersaturated Al-Sc alloys, it is demonstrated how the model can be used to calculate number densities and size distributions of precipitates as a function of aging time and temperature, including effects of continuous cooling and thermally generated point defects. Application of the model to a specific alloy system requires knowledge of diffusion data, point defect energetics, and thermodynamic properties for bulk phases and interphase interfaces. For interfaces and point defects, thermodynamic data can be difficult to measure and reliable values of defect free energies are often unavailable. For this reason, part of the efforts were devoted to applying semiempirical and first-principles atomistic techniques to the calculation of interfacial and point-defect thermodynamic properties. This report discusses applications for interphase interfaces in the Al-Ag, Al-Sc, and Al-Li alloy systems. We also describe atomistic work aimed at understanding the energetics of vacancy clusters in Al. These clusters serve as sinks for isolated vacancies during aging and their growth can lead to more complex defects, such as dislocation loops, that act as heterogeneous nucleation sites.

  6. How common are ALS plateaus and reversals?

    PubMed Central

    Vaughan, Timothy; Wicks, Paul; Heywood, Jamie; Sinani, Ervin; Selsov, Roger; Macklin, Eric A.; Schoenfeld, David; Cudkowicz, Merit; Sherman, Alex

    2016-01-01

    Objective: To determine the frequency of amyotrophic lateral sclerosis (ALS) plateaus and reversals in the Pooled Resource Open-Access ALS Clinical Trials (PRO-ACT) database. Methods: We analyzed Amyotrophic Lateral Sclerosis Functional Rating Scale (ALSFRS) and ALSFRS–revised (ALSFRS-R) data from PRO-ACT participants. The frequencies of participants experiencing plateaus (periods where scores did not change) were calculated over 6-, 12-, and 18-month epochs. The percentage of participants ever experiencing reversals (periods where scores improved) of different lengths were also calculated and plotted. Results: Over 6 months, 25% of 3,132 participants did not decline. Over 12 months, 16% of 2,105 participants did not decline. Over 18 months, 7% of 1,218 participants did not decline. Small ALS reversals were also common, especially over shorter follow-up intervals; 14% of 1,343 participants had a 180-day interval where their ALSFRS-R slope was greater than zero. Fewer than 1% of participants ever experienced improvements of 4 or more ALSFRS-R points lasting at least 12 months. Conclusion: ALS plateaus and small reversals are common, especially over brief intervals. In light of these data, stable disease, especially for a short period of time, should not be interpreted as an ALS treatment effect. Large sustained ALS reversals, on the other hand, are rare, potentially important, and warrant further study. PMID:26658909

  7. Microscopic Properties of Long-Period Ordering in Al-Rich TiAl Alloys

    NASA Astrophysics Data System (ADS)

    Hata, S.; Nakano, T.; Kuwano, N.; Itakura, M.; Matsumura, S.; Umakoshi, Y.

    2008-07-01

    The ordering mechanism of long-period superstructures (LPSs) in Al-rich TiAl alloys has been investigated by high-resolution transmission electron microscopy (HRTEM). The LPSs are classified in terms of arrangements of base clusters with different shapes and compositions formed in Ti-rich (002) layers of L10-TiAl matrix: square Ti4Al, fat rhombus Ti3Al, and lean rhombus Ti2Al type clusters. The HRTEM observations revealed that antiphase boundaries of long-range-ordered LPS domains and short-range-ordered microdomains are constructed by various space-filling arrangements of the base clusters. Such a microscopic property characterized by the base clusters and their arrangements is markedly analogous to that of the {left< {{text{1,1/2,0}}} rightrangle } * special-point ordering alloys such as Ni-Mo.

  8. Effects of Al(III) and nano-Al13 species on malate dehydrogenase activity.

    PubMed

    Yang, Xiaodi; Cai, Ling; Peng, Yu; Li, Huihui; Chen, Rong Fu; Shen, Ren Fang

    2011-01-01

    The effects of different aluminum species on malate dehydrogenase (MDH) activity were investigated by monitoring amperometric i-t curves for the oxidation of NADH at low overpotential using a functionalized multi-wall nanotube (MWNT) modified glass carbon electrode (GCE). The results showed that Al(III) and Al(13) can activate the enzymatic activity of MDH, and the activation reaches maximum levels as the Al(III) and Al(13) concentration increase. Our study also found that the effects of Al(III) and Al(13) on the activity of MDH depended on the pH value and aluminum speciation. Electrochemical and circular dichroism spectra methods were applied to study the effects of nano-sized aluminum compounds on biomolecules. PMID:22163924

  9. TEM studies of oxidized NiAl and Ni3Al cross sections

    NASA Technical Reports Server (NTRS)

    Doychak, J.; Ruhle, M.

    1989-01-01

    Cross sections of oxide scale/(Ni-Al) intermetallics were prepared by a new method and studied using primarily TEM. The cross sections were prepared by encasing an oxidized metal specimen sandwich in a low-melting-temperature zinc alloy. Observations of oxidized zirconium-doped beta-NiAl cross sections revealed crystallographic voids beneath an adherent Al2O3 scale. The oxide-metal interface was incoherent, but a high dislocation density in the metal near the interface suggested that a large tensile stress was induced by the attached oxide scale. A duplex Al2O3-NiAl2O4 scale formed on zirconium-doped and zirconium/boron-doped gamma-prime-Ni3Al alloys. Additional results are presented involving oxidation mechanisms and oxide-metal interface structures.

  10. Scattering induced by Al segregation in AlGaN/GaN heterostructures

    SciTech Connect

    Liu, Xiwen; Lu, Yanwu; Ji, Dong

    2015-08-17

    The effect of Al segregation near dislocations on the mobility of two-dimensional electron gas in AlGaN/GaN heterostructure-based high-electron-mobility transistors was investigated. Exponentially varied composition fluctuation was effective in describing Al segregation near dislocations when calculating scattering behavior. Mobility, which was limited by Al segregation surrounding dislocation lines, was calculated to be in the order of 10{sup 3} cm{sup 2}/Vs to 10{sup 6} cm{sup 2}/Vs. Results indicated that the mobility in AlGaN/GaN heterojunction was enhanced upon the reduction of dislocation density at low temperature. This study contributes to generating higher electron mobility in AlGaN/GaN heterojunctions.

  11. Thermal Properties in the MgAl2O4-Al2O3 System

    SciTech Connect

    Wilkerson, Dr. Kelley R.; Smith, Jeffrey D; Hemrick, James Gordon

    2013-01-01

    Compositional effects on the thermal diffusivity in the MgAl2O4-Al2O3 system were studied. The lowest thermal diffusivity, 0.0258 +/-5% cm/s, was measured between 79.8 and 83.9 wt% Al2O3 quenched from various temperatures between 1500 and 1700C. All of the chemistries in this range extend past the solvus, but still form a singe super-saturated spinel solid solution, regardless of quenching tempeature. A super-saturated metastable solid solution region was observed at 1500, 1600, and 1700C extending to 83.9, 85.2, and 87.1 wt% Al2O3, respectively. Beyond 83.9% Al2O3 a significant increase in thermal diffusivity, 11.7%, was observed and its attributed to precipiation of Al2O3 through spinodal decomposition.

  12. Excited states of 26Al studied via the reaction 27Al(d,t)

    NASA Astrophysics Data System (ADS)

    Srivastava, Vishal; Bhattacharya, C.; Rana, T. K.; Manna, S.; Kundu, S.; Bhattacharya, S.; Banerjee, K.; Roy, P.; Pandey, R.; Mukherjee, G.; Ghosh, T. K.; Meena, J. K.; Roy, T.; Chaudhuri, A.; Sinha, M.; Saha, A. K.; Asgar, Md. A.; Dey, A.; Roy, Subinit; Moin Shaikh, Md.

    2016-05-01

    The reaction 27Al(d,t) at 25 MeV was utilized to study the excited states of 26Al. The angular distributions of the observed excited states of 26Al were analyzed with zero range distorted wave Born approximation as well as by incorporating finite range correction parameters to extract spectroscopic factors. The two sets of extracted spectroscopic factors were compared with each other to see the effect of using finite range correction in the transfer form factor.

  13. Temperature dependence diode parameters studies of Al/CuPc/n-Si/Al structure

    NASA Astrophysics Data System (ADS)

    Kumar, Ratnesh; Kaur, Ramneek; Sharma, Mamta; Kaur, Maninder; Tripathi, S. K.

    2015-08-01

    This paper presents the fabrication of Al/CuPc/n-Si/Al metal-organic-semiconductor diode. The copper phthalocyanine as organic layer is deposited on Si substrate by thermal evaporation technique. The temperature dependent current-voltage measurements are performed on Al/CuPc/n-Si structure. The important diode parameters i.e. the barrier height and ideality factor have been calculated. The temperature dependence of barrier height and ideality factor has been studied.

  14. Influence of RCS on Al-3Mg and Al-3Mg-0.25Sc alloys

    NASA Astrophysics Data System (ADS)

    Bhovi, Prabhakar M.; Venkateswarlu, K.

    2016-02-01

    An influence of repetitive corrugation and straightening (RCS) was studied on Al-3Mg and Al-3Mg-0.25Sc alloys up to eight passes. Each pass consist of a corrugation and followed by straightening. This has resulted in introducing large plastic strain in sample, and thus led to formation of sub-micron grain sizes with high angle grain boundaries. These sub grain formation was eventually resulted in improved mechanical properties. The average grain size of Al-3Mg-0.25Sc alloy after 8 passes yielded to ∼0.6pm. Microhardness, strength properties were evaluated and it suggests that RCS was responsible for high hardness values as compared to the as cast samples. The microhardness values after RCS were 105 HV and 130 HV for Al-3Mg and Al-3Mg-0.25Sc alloys, respectively. Similarly, ∼ 40% improvement in tensile strength from 240 MPa to 370 MPa was observed for Al- 3Mg-0.25Sc alloy after RCS process.Al-3Mg and Al-3Mg-0.25Scalloys exhibited maximum strength of 220 MPa and 370 MPa, respectively. It is concluded that RCS process has a strong influence on Al- 3Mg and Al-3Mg-0.25Sc alloys for obtaining improved mechanical properties and grain refinement. In addition to RCS process and presence of AESc precipitates in Al-3Mg-0.25Sc alloy had a significant role in grain refinement and improved mechanical properties as compared to Al-3Mg alloy.

  15. Remarks on Peinado et al.'s Analysis of J3Gen.

    PubMed

    Garcia-Alfaro, Joaquin; Herrera-Joancomartí, Jordi; Melià-Seguí, Joan

    2015-01-01

    Peinado et al. analyzed the security of the J3Gen pseudorandom number generator proposed by Melià-Seguí et al., and claimed weaknesses regarding its security properties. They also presented a deterministic attack based on the decimation of the J3Gen output sequences. We show that the assumptions made by Peinado et al. are not correct and that the proposed deterministic attack against J3Gen does not hold in practice. PMID:25781510

  16. Two-Phase (TiAl+TiCrAl) Coating Alloys for Titanium Aluminides

    NASA Technical Reports Server (NTRS)

    Brady, Michael P. (Inventor); Smialek, James L. (Inventor); Brindley, William J. (Inventor)

    1998-01-01

    A coating for protecting titanium aluminide alloys, including the TiAl gamma + Ti3Al (alpha(sub 2)) class, from oxidative attack and interstitial embrittlement at temperatures up to at least 1000 C. is disclosed. This protective coating consists essentially of titanium, aluminum. and chromium in the following approximate atomic ratio: Ti(41.5-34.5)Al(49-53)Cr(9.5-12.5)

  17. Another Security Improvement over the Lin et al.'s E-voting Scheme

    NASA Astrophysics Data System (ADS)

    Asaar, Maryam Rajabzadeh; Mohajeri, Javad; Salmasizadeh, Mahmoud

    In 2003, Lin et al. have proposed an electronic voting scheme which can be utilized in large-scale elections, and claimed it detects double voting. But in this paper, by presenting an attack, we show that voters can successfully vote more than once without being detected. Hence, we propose a new modified scheme based on the Lin et al.'s scheme with the same efficiency to solve this weakness and analyze its security.

  18. The lowest ionization potentials of Al2

    NASA Technical Reports Server (NTRS)

    Bauschlicher, Charles W., Jr.; Barnes, Leslie A.; Taylor, Peter R.

    1988-01-01

    Potential curves for the lowest two electronic states (X 2 sigma g + and A 2 pi u) of Al2(+) were computed using complete active space SCF/multireference CI wave functions and large Gaussian basis sets. The lowest observable vertical ionization potential (to Al2(+) X 2 sigma g +) of the Al2 X 3 pi u ground state is calculated to occur around 6.1 eV, in excellent agreement with the experimental range of 6.0 to 6.42 eV obtained in recent cluster ionization studies by Cox and co-workers. The second vertical ionization potential (to Al2(+) A 2 pi u) occurs near 6.4 eV, also within the experimental range. The adiabatic IP of 5.90 eV is in good agreement with the value of 5.8 to 6.1 eV deduced by Hanley and co-workers from the difference in thresholds between collision induced dissociation processes of Al3(+). The computed IP values are somewhat larger than those deduced from branching ratios in cluster fragmentation experiments by Jarrold and co-workers. The observation of an ionization threshold below 6.42 eV is shown to be incompatible with an Al2 ground electronic state assignment of 3 sigma g -, but the separation between the two lowest states of Al2 is so small that it is likely that both are populated in the experiments, so that this does not provide unambiguous support for the recent theoretical assignment of the ground state as 3 pi u.

  19. The new structure type Gd3Ni7Al14.

    PubMed

    Pukas, Svitlana; Gladyshevskii, Roman

    2015-11-01

    The crystal structure of Gd3Ni7Al14 (trigadolinium heptanickel tetradecaaluminide) belongs to a family of two-layer structures and can be described as an assembly of interpenetrating centred straight prisms. For the Ni atoms, trigonal prisms (Al4Gd2 and Al6) are observed, the Al atoms are inside tetragonal (Ni2Al2Gd4, Ni2Al4Gd2, Al4Gd4, Ni4Al4 and Al8) and pentagonal (Ni4Al6 and Al10) prisms, while the Gd atoms are at the centres of pentagonal (Ni4Al6) and hexagonal (Ni4Al8) prisms. In each case, the true coordination polyhedron is a capped prism, also including atoms from the same layer. The structural features of Gd3Ni7Al14 are similar to those of the intermetallides PrNi2Al3 and ZrNiAl. In all these structures, Ni-centred trigonal prisms form infinite columns via common triangular faces. The columns share prism edges and form a three-dimensional framework with six-membered rings in the (001) plane in the case of the PrNi2Al3 and ZrNiAl types. In the case of Gd3Ni7Al14, six-membered rings are also observed, but only two-thirds of the rings are interconnected via prism edges. PMID:26524174

  20. Long range order and vacancy properties in Al-rich Fe{sub 3}Al and Fe{sub 3}Al(Cr) alloys

    SciTech Connect

    Kim, S.M.; Morris, D.G.

    1998-05-01

    Neutron powder diffraction measurements have been carried out in situ from room temperature to about 100 C in Fe28Al (28 at.% Al), Fe32.5Al (32.5 at.% Al) and Fe28Al15Cr (28 at.% Al, 5 at.% Cr) alloys. X-ray diffraction and TEM studies provided supporting information. The data were analyzed to obtain information about the temperature dependence of the DO{sub 3} and B2 long range order parameters, the location of the Cr atoms and their effect on the ordering energies, and on the vacancy formation and migration properties in Fe28Al and Fe32.5Al alloys. The location of the ternary alloying addition in DO{sub 3} and B2 ordered Al-rich Fe{sub 3}Al is shown to be consistent with considerations of interatomic bond energies.

  1. Synthesis of core-shell AlOOH hollow nanospheres by reacting Al nanoparticles with water.

    PubMed

    Lozhkomoev, A S; Glazkova, E A; Bakina, O V; Lerner, M I; Gotman, I; Gutmanas, E Y; Kazantsev, S O; Psakhie, S G

    2016-05-20

    A novel route for the synthesis of boehmite nanospheres with a hollow core and the shell composed of highly crumpled AlOOH nanosheets by oxidizing Al nanopowder in pure water under mild processing conditions is described. The stepwise events of Al transformation into boehmite are followed by monitoring the pH in the reaction medium. A mechanism of formation of hollow AlOOH nanospheres with a well-defined shape and crystallinity is proposed which includes the hydration of the Al oxide passivation layer, local corrosion of metallic Al accompanied by hydrogen evolution, the rupture of the protective layer, the dissolution of Al from the particle interior and the deposition of AlOOH nanosheets on the outer surface. In contrast to previously reported methods of boehmite nanoparticle synthesis, the proposed method is simple, and environmentally friendly and allows the generation of hydrogen gas as a by-product. Due to their high surface area and high, slit-shaped nanoporosity, the synthesized AlOOH nanostructures hold promise for the development of more effective catalysts, adsorbents, vaccines and drug carriers. PMID:27053603

  2. HYDROGEN ADSORPTION ON β-TiAl (001) AND Ni/TiAl (001) SURFACES

    NASA Astrophysics Data System (ADS)

    Mubarak, A. A. Karim; Alelaimi, Mahmoud

    2014-04-01

    In this paper, we present first principles calculations of the energetic, electronic and magnetic properties of the variant termination of TiAl (001) and Ni/TiAl (001) surfaces with and without hydrogen atoms. The calculations have been performed within the density functional theory using full-potential linearized augmented plane wave method. The generalized gradient approximation (GGA) is utilized as the exchange-correlation energy. The octahedral site is the stable absorption site of H atom in the β-TiAl system. This absorption reduces the cohesive energy of β-TiAl system due to increase in the lattice constant. The surface energy for both TiAl (001) terminations is calculated. The stable adsorption site of H atoms on the variant termination of TiAl (001) surface is performed. The adsorption energy of hydrogen on Ti is more energetic than that on Al. The adsorption of H atom on both terminations of H/Ni/TiAl (001) is more preferable at the bridge site. The adsorption energies are enhanced on Ni atom due to the contraction between d-Ni bands and TiAl substrate band.

  3. Synthesis of core–shell AlOOH hollow nanospheres by reacting Al nanoparticles with water

    NASA Astrophysics Data System (ADS)

    Lozhkomoev, A. S.; Glazkova, E. A.; Bakina, O. V.; Lerner, M. I.; Gotman, I.; Gutmanas, E. Y.; Kazantsev, S. O.; Psakhie, S. G.

    2016-05-01

    A novel route for the synthesis of boehmite nanospheres with a hollow core and the shell composed of highly crumpled AlOOH nanosheets by oxidizing Al nanopowder in pure water under mild processing conditions is described. The stepwise events of Al transformation into boehmite are followed by monitoring the pH in the reaction medium. A mechanism of formation of hollow AlOOH nanospheres with a well-defined shape and crystallinity is proposed which includes the hydration of the Al oxide passivation layer, local corrosion of metallic Al accompanied by hydrogen evolution, the rupture of the protective layer, the dissolution of Al from the particle interior and the deposition of AlOOH nanosheets on the outer surface. In contrast to previously reported methods of boehmite nanoparticle synthesis, the proposed method is simple, and environmentally friendly and allows the generation of hydrogen gas as a by-product. Due to their high surface area and high, slit-shaped nanoporosity, the synthesized AlOOH nanostructures hold promise for the development of more effective catalysts, adsorbents, vaccines and drug carriers.

  4. AlN/IDT/AlN/Sapphire SAW Heterostructure for High-Temperature Applications.

    PubMed

    Legrani, Ouarda; Aubert, Thierry; Elmazria, Omar; Bartasyte, Ausrine; Nicolay, Pascal; Talbi, Abdelkrim; Boulet, Pascal; Ghanbaja, Jaafar; Mangin, Denis

    2016-06-01

    Recent studies have evidenced that Pt/AlN/Sapphire surface acoustic wave (SAW) devices are promising for high-temperature high-frequency applications. However, they cannot be used above 700°C in air atmosphere as the Pt interdigital transducers (IDTs) agglomerate and the AlN layer oxidizes in such conditions. In this paper, we explore the possibility to use an AlN protective overlayer to concurrently hinder these phenomena. To do so, AlN/IDT/AlN/Sapphire heterostructures undergo successive annealing steps from 800°C to 1000°C in air atmosphere. The impact of each step on the morphology, microstructure, and phase composition of AlN and Pt films is evaluated using optical microscopy, scanning and transmission electron microscopy (SEM and TEM), X-ray diffraction (XRD), and secondary ion mass spectroscopy (SIMS). Finally, acoustical performance at room temperature of both protected and unprotected SAW devices are compared, as well as the effects of annealing on these performance. These investigations show that the use of an overlayer is one possible solution to strongly hinder the Pt IDTs agglomeration up to 1000°C. Moreover, AlN/IDT/AlN/Sapphire SAW heterostructures show promising performances in terms of stability up to 800°C. At higher temperatures, the oxidation of AlN is more intense and makes it inappropriate to be used as a protective layer. PMID:27076407

  5. Strain Rates and Grain Growth in Al 5754 and Al 6061 Friction Stir Spot Welds

    NASA Astrophysics Data System (ADS)

    Gerlich, A.; Yamamoto, M.; North, T. H.

    2007-06-01

    The stir zone temperature and microstructures are compared in friction stir spot welds produced in Al 5754 and Al 6061 alloys. Electron backscattered diffraction was used to determine the relationship between tool rotation speed during welding and final stir zone grain size. Comparison of the grain sizes in rapidly quenched welds with those in air-cooled joints confirmed that grain growth occurred only in Al 6061 spot welds. There was no evidence of abnormal grain growth in the stir zones of Al 6061 welds; the final grain size could be represented using an Arrhenius equation. The strain rates during welding were determined by incorporating the stir zone temperature and average subgrain sizes in quenched spot welds in the Zener-Hollomon relation. When the tool rotation speed increased from 750 to 3000 RPM, the strain rate values ranged from 180 to 497 s-1 in Al 5754 spot welds and from 55 to 395 s-1 in Al 6061 spot welds. It is suggested that a no-slip boundary condition may be appropriate during numerical modeling of Al 5754 and 6061 friction stir spot welding. This is not the case during Al 7075, Al 2024, and Mg-alloy AZ91 spot welding because spontaneous melting facilitates slippage at the tool contact interface.

  6. High temperature deformation of NiAl and CoAl

    NASA Technical Reports Server (NTRS)

    Nix, W. D.

    1982-01-01

    The high temperature mechanical properties of the aluminides are reviewed with respect to their potential as high temperature structural materials. It is shown that NiAl and CoAl are substantially stronger than the pure metals Ni and Co at high temperatures and approach the strength of some superalloys, particularly when those superalloys are tested in "weak" directions. The factors that limit and control the high temperature strengths of NiAl and CoAl are examined to provide a basis for the development of intermetallic alloys of this type.

  7. Small Al clusters. II - Structure and binding in Al(n) (n = 2-6, 13)

    NASA Technical Reports Server (NTRS)

    Pettersson, Lars G. M.; Bauschlicher, Charles W., Jr.; Halicioglu, Timur

    1987-01-01

    The structure and stability of aluminum clusters containing up to six atoms have been studied using correlated wave functions and extended basis sets. The lowest energy structure is planar for Al4 and Al5, but three dimensional for Al6. The icosahedral, hcp, fcc, and two planar structures of Al13 were considered at the SCF level. The lowest energy structure is the icosahedron, but the planar structures are fairly low lying even in this case. A simplified description using two- and three-body interaction potentials is found to agree well with the ab initio structures and binding energies.

  8. Microstructure and strengthening of creep-tested cryomilled NiAl-AlN

    SciTech Connect

    Garg, A.; Whittenberger, J.D.; Luton, M.J.

    1997-12-31

    The B2 intermetallic NiAl is considered to be a prime candidate material for use as very high temperature structural components in gas turbine engines. The mechanical grinding of prealloyed NiAl powder in liquid nitrogen (cryomilling) results in an intermetallic matrix composite where micron sized particle free aluminide cores (grains) are surrounded by thin mantles comprised of nanometer sized AlN particles and NiAl grains. Under high temperature, slow strain rate conditions both compressive and tensile creep testing have shown that the mechanical strength of hot extruded cryomilled NiAl approaches the levels exhibited by advanced NiAl-based single crystals and simple Ni-based superalloys. Transmission electron microscopy of cryomilled materials tested between 1,100 and 1,300 K revealed little, if any, dislocation structure within the mantle regions, while the NiAl cores contained subgrains and dislocation networks after testing at all strain rates between 10{sup {minus}4} and 10{sup {minus}8} s{sup {minus}1}. These and other microstructural observations suggest that creep strength is the result of a fine NiAl grain/subgrain size, the inability of dislocations to move through the mantle and stabilization of the microstructure by the AlN particles.

  9. Quantum chemical study of the reactions of Al, AlO and AlOH with H2O2

    NASA Astrophysics Data System (ADS)

    Sharipov, Alexander S.; Starik, Alexander M.

    2016-02-01

    Quantum chemical calculations with the use of hybrid density functional with perturbative second-order correlation and dispersion correction are carried out to study the reactions of Al, AlO and AlOH with the H2O2 molecule. The values of energy barriers are estimated by means of extrapolation to the basis set limit. The energetically favorable reaction pathways have been revealed during the examination of the potential energy surfaces. Complex character of the processes under study has been established. It has been found that the initial stages of the considered processes are barrierless. Appropriate rate constants for principal channels of the reactions under study have been estimated by using capture model and canonical variational theory. The Arrhenius approximations for these channels have been proposed for the temperature range T = 300-4000 K.

  10. Reactions of CO2 on solid and liquid Al100+.

    PubMed

    Leslie, Katheryne L; Shinholt, Deven; Jarrold, Martin F

    2013-02-14

    The reactions of CO(2) on the Al(100)(+) cluster have been investigated as a function of cluster temperature (300-1100 K) and relative kinetic energy (0.2-10 eV). Two main products are observed at low cluster temperature: Al(100)O(+) (which is believed to result from a stripping reaction) and Al(100)CO(2)(+) from complex formation. As the cluster temperature is raised, both products dissociate by loss of Al(2)O. Al(100)O(+) forms Al(98)(+), while Al(100)CO(2)(+) forms Al(98)CO(+) and Al(96)C(+). In both cases, loss of Al(2)O turns-on above the melting temperature of Al(100)(+). This presumably occurs because the overall reaction leading to the loss of Al(2)O is significantly less endothermic for the liquid cluster than for the solid. PMID:22680973

  11. Coating of a layer of Au on Al13 : The findings of icosahedral Al@Al12Au20- and Al12Au202- fullerenes using ab initio pseudopotential calculations

    NASA Astrophysics Data System (ADS)

    Kumar, Vijay

    2009-02-01

    We report results of ab initio pseudopotential calculations on the nanocoating of gold on an icosahedral Al13 cluster and the findings of icosahedrally symmetric endohedral Al@Al12Au20- and empty cage Al12Au202- compound fullerenes formed of metal atoms. Twelve Al atoms cap the pentagonal faces of a dodecahedral Au20 cage in which each Au atom has three Al atoms and three Au atoms as nearest neighbors. Mixing of Al13 and Au20 magic clusters leads to a large heat of formation of 0.55 eV/atom and high stability of the Al@Al12Au20 compound fullerene. The binding energies of Al12Au20 and Al@Al12Au20 are 3.017 and 3.007 eV/atom, respectively, which are much larger than 2.457 eV/atom for Au32 fullerene, leading to the possibility of their high abundance.

  12. Survey and alignment at the ALS

    SciTech Connect

    Krebs, G.F.; Lauritzen, T.; Thur, W.

    1995-11-01

    This paper describes survey and alignment at the Lawrence Berkeley National Laboratory`s Advanced Light Source (ALS) accelerators from 1993 to 1995. The ALS is a 1.0 - 1.9 GeV electron accelerator producing extremely bright synchrotron light in the UV and soft-X-ray wavelengths. At the ALS, electrons are accelerated in a LINAC to 50 MeV, injected into a booster ring for further acceleration and finally injected into the storage ring. This is shown schematically in Figure 1. The storage ring, some 200 m in circumference, has been run with electron currents above 400 mA with lifetimes as high as 24 hours. The ALS is a third generation light source and requires for efficient storage ring operation, magnets aligned to within 150 mm of their ideal position. To accomplish this a network of monuments was established and their positions measured with respect to one another. The data was reduced using GEONET`` and STAR*NET`` software. Using the monuments as reference points, magnet positions were measured and alignment confirmed using the Kem Electronic Coordinate Determination System (ECDS``). A number of other papers dealing with survey and alignment (S&A) at the ALS have been written that may further elucidate some details of the methods and systems described in this paper.

  13. The mechanical properties of FeAl

    SciTech Connect

    Baker, I.; George, E.P.

    1996-12-31

    Only in the last few years has progress been made in obtaining reproducible mechanical properties data for FeAl. Two sets of observations are the foundation of this progress. The first is that the large vacancy concentrations that exist in FeAl at high temperature are easily retained at low temperature and that these strongly affect the low-temperature mechanical properties. The second is that RT ductility is adversely affected by water vapor. Purpose of this paper is not to present a comprehensive overview of the mechanical properties of FeAl but rather to highlight our understanding of key phenomena and to show how an understanding of the factors which control the yield strength and fracture behavior has followed the discovery of the above two effects. 87 refs, 9 figs.

  14. Boron strengthening in FeAl

    SciTech Connect

    Baker, I.; Li, X.; Xiao, H.; Klein, O.; Nelson, C.; Carleton, R.L.; George, E.P.

    1998-11-01

    The effect of boron on the strength of B2-structured FeAl is considered as a function of composition, grain size and temperature. Boron does not affect the concentrations of antisite atoms or vacancies present, with the former increasing and the latter decreasing with increasing deviation from the stoichiometric composition. When vacancies are absent, the strength increase per at. % B per unit lattice strain, {Delta}{sigma}/({Delta}c x {epsilon}) increases with increasing aluminum concentration, but when vacancies are present (>45 at. % Al), {Delta}{sigma}/({Delta}c x {epsilon}) decreases again. Boron increases grain size strengthening in FeAl. B strengthening is roughly independent of temperature up to the yield strength peak but above the point, when diffusion-assisted deformation occurs, boron strengthening increases dramatically.

  15. Primary (AL) amyloidosis in plasma cell disorders.

    PubMed

    Müller, Antonia M S; Geibel, Annette; Neumann, Hartmut P H; Kühnemund, Alexander; Schmitt-Gräff, Annette; Böhm, Joachim; Engelhardt, Monika

    2006-01-01

    Primary (AL) amyloidosis is the most common form of systemic amyloidosis. The morbidity arises from extracellular deposition of immunoglobulin light chain (LC) fibrils in major organs, such as the kidneys, heart, and bowel. Organ dysfunction contributes to a high mortality and poor prognosis, with a median survival time of 1-2 years from diagnosis. Here, we present a 46-year-old man with an exceptional clinical course of an LC multiple myeloma with generalized amyloidosis, causing renal insufficiency, congestive heart failure, and complete intestinal necrosis. We have summarized recent knowledge on AL amyloidosis, its association with monoclonal gammopathies, clinical presentations, diagnostic tools, and treatment strategies. Our comprehensive overview of this rare and often fatal disease aims to increase the awareness of AL amyloidosis. This may facilitate earlier diagnosis, and thus allow initiation of prompt and specific therapies, which are indispensable in order to improve disease prognosis. PMID:16880241

  16. Disordered crystal structure of 20H-AlON, Al10O3N8

    NASA Astrophysics Data System (ADS)

    Banno, Hiroki; Funahashi, Shiro; Asaka, Toru; Hirosaki, Naoto; Fukuda, Koichiro

    2015-10-01

    The disordered crystal structure of 20H-AlON (Al10O3N8) was determined by combined use of X-ray powder diffraction and transmission electron microscopy. The title compound is hexagonal with space group P63/mmc (Z=2) and the unit-cell dimensions are a=0.307082(5) nm, c=5.29447(8) nm and V=0.432376(12) nm3. The structural model showed the positional disordering of three of the six Al sites in the unit cell. The reliability indices calculated from the Rietveld method were Rwp=6.97%, S (=Rwp/Re)=1.68, Rp=5.45%, RB=5.13% and RF=4.56%. We interpreted the disordered structure of 20H-AlON as a statistical average of six different types of ordered structural configurations, which are composed of an octahedral [Al(O, N)6] layer and tetrahedral [Al(O, N)4] layers. We demonstrated the high correlations between the hexagonal unit-cell dimensions and the octahedral layer concentrations for AlON and SiAlON polytypoids.

  17. Directional Solidification and Mechanical Properties of NiAl-NiAlTa Alloys

    NASA Technical Reports Server (NTRS)

    Johnson, D. R.; Chen, X. F.; Oliver, B. F.; Noebe, R. D.; Whittenberger, J. D.

    1995-01-01

    Directional solidification of eutectic alloys is a promising technique for producing in-situ composite materials exhibiting a balance of properties. Consequently, the microstructure, creep strength and fracture toughness of directionally solidified NiAl-NiAlTa alloys were investigated. Directional solidification was performed by containerless processing techniques to minimize alloy contamination. The eutectic composition was found to be NiAl-15.5 at% Ta and well-aligned microstructures were produced at this composition. A near-eutectic alloy of NiAl-14.5Ta was also investigated. Directional solidification of the near-eutectic composition resulted in microstructures consisting of NiAl dendrites surrounded by aligned eutectic regions. The off-eutectic alloy exhibited promising compressive creep strengths compared to other NiAl-based intermetallics, while preliminary testing indicated that the eutectic alloy was competitive with Ni-base single crystal superalloys. The room temperature toughness of these two-phase alloys was similar to that of polycrystalline NiAl even with the presence of the brittle Laves phase NiAlTa.

  18. Adhesion of metal carbide/nitride interfaces: Al/TiC and Al/TiN

    NASA Astrophysics Data System (ADS)

    Liu, L. M.; Wang, S. Q.; Ye, H. Q.

    2003-12-01

    We employ density functional theory to investigate and compare Al/TiC and Al/TiN interfaces by electronic structures, relaxed atomic geometries and adhesions. The results show that the preferred bonding site is the interfacial Al atoms above the ceramic's metalloid atoms for both systems. The calculated adhesion energies are quantitatively in agreement with other calculated and experimental results of Al on the carbide and nitride. A detailed comparison of the adhesion energies and relaxed structures shows weaker bonding and less relaxation in the Al/nitride case, which is correlated with the lower surface energy of the ceramic. We have thoroughly characterized the electronic structure and determined that the polar covalent Al3sp-C(N)2s bonds constitute the primary interfacial bonding interaction. The larger overlapping bonding states at the Al/TiC interface reveal the reason why it exhibits relatively larger adhesion energy. Cleavage may take place preferentially at the interface, especially for the Al/TiN, which is in agreement with experimental results.

  19. Transport mechanisms of leakage current in Al2O3/InAlAs MOS capacitors

    NASA Astrophysics Data System (ADS)

    Jin, Chengji; Lu, Hongliang; Zhang, Yimen; Zhang, Yuming; Guan, He; Wu, Lifan; Lu, Bin; Liu, Chen

    2016-09-01

    An Al2O3 layer is inserted between the InAlAs layer and the metal gate in InAs/AlSb HEMTs to suppress the leakage current. The transport mechanisms of leakage current in Al2O3/InAlAs metal-oxide-semiconductor (MOS) capacitors at both positive and negative biases at different temperatures ranging from 10 °C to 70 °C are investigated. For positive bias, the leakage current is dominated by Schottky emission. Based on the fitted straight lines, the relative dielectric constant of Al2O3 and the barrier height between Al2O3 and InAlAs are extracted. However, for negative bias, the leakage current is dominated by Frenkel-Poole (F-P) emission and the depth of the trap energy level from the conduction band (ϕt) is extracted. Furthermore, authors explain the reason why the dominating mechanisms at positive and negative biases are different.

  20. Electronic circuits having NiAl and Ni.sub.3 Al substrates

    DOEpatents

    Deevi, Seetharama C.; Sikka, Vinod K.

    1999-01-01

    An electronic circuit component having improved mechanical properties and thermal conductivity comprises NiAl and/or Ni.sub.3 Al, upon which an alumina layer is formed prior to applying the conductive elements. Additional layers of copper-aluminum alloy or copper further improve mechanical strength and thermal conductivity.

  1. An Alternative Perspective on von Winterfeldt et al.'s (1997) Test of Consequence Monotonicity

    ERIC Educational Resources Information Center

    Ho, Moon-Ho R.; Regenwetter, Michel; Niederee, Reinhard; Heyer, Dieter

    2005-01-01

    D. von Winterfeldt, N.-K. Chung, R. D. Luce, and Y. Cho (see record 1997-03378-008) provided several tests for consequence monotonicity of choice or judgment, using certainty equivalents of gambles. The authors reaxiomatized consequence monotonicity in a probabilistic framework and reanalyzed von Winterfeldt et al.'s main experiment via a…

  2. Melting, Processing, and Properties of Disordered Fe-Al and Fe-Al-C Based Alloys

    NASA Astrophysics Data System (ADS)

    Satya Prasad, V. V.; Khaple, Shivkumar; Baligidad, R. G.

    2014-09-01

    This article presents a part of the research work conducted in our laboratory to develop lightweight steels based on Fe-Al alloys containing 7 wt.% and 9 wt.% aluminum for construction of advanced lightweight ground transportation systems, such as automotive vehicles and heavy-haul truck, and for civil engineering construction, such as bridges, tunnels, and buildings. The melting and casting of sound, porosity-free ingots of Fe-Al-based alloys was accomplished by a newly developed cost-effective technique. The technique consists of using a special flux cover and proprietary charging schedule during air induction melting. These alloys were also produced using a vacuum induction melting (VIM) process for comparison purposes. The effect of aluminum (7 wt.% and 9 wt.%) on melting, processing, and properties of disordered solid solution Fe-Al alloys has been studied in detail. Fe-7 wt.% Al alloy could be produced using air induction melting with a flux cover with the properties comparable to the alloy produced through the VIM route. This material could be further processed through hot and cold working to produce sheets and thin foils. The cold-rolled and annealed sheet exhibited excellent room-temperature ductility. The role of carbon in Fe-7 wt.% Al alloys has also been examined. The results indicate that Fe-Al and Fe-Al-C alloys containing about 7 wt.% Al are potential lightweight steels.

  3. Synthesis of nanostructured AlN by solid state reaction of Al and diaminomaleonitrile

    SciTech Connect

    Rounaghi, S.A.; Eshghi, H.; Kiani Rashid, A.R.; Vahdati Khaki, J.; Samadi Khoshkhoo, M.; Scudino, S.; Eckert, J.

    2013-02-15

    The solid state reaction of diaminomaleonitrile (DAMN) with aluminum via both mechanochemical and thermal treatment routes was studied by X-ray diffraction and Fourier transform infrared spectroscopy. During the milling process, the reaction starts with the deammoniation of the DAMN molecules, followed by the formation of nanostructured AlN powder as the main solid product after milling for 7 h. The reactivity of the mixed powder was also investigated during the conventional thermal treatment process using differential scanning calorimetry, derivative thermogravimetry and thermogravimetric analysis. The results reveal that DAMN starts to polymerize at 192 Degree-Sign C by the elimination of the amine groups. Furthermore, increasing the annealing temperature leads to the formation of a nitrogen-containing carbonaceous material with the structure similar to non-crystalline carbon. However, no evidence for the formation of AlN was observed in the annealed samples even at temperatures as high as the Al melting point. - Graphical abstract: AlN nanoparticles obtained after milling of Al and diaminomaleonitrile (DAMN) for 12 h. Highlights: Black-Right-Pointing-Pointer Solid state reaction of diaminomaleonitrile (DAMN) with Al was studied via mechanochemical and thermal treatment routs. Black-Right-Pointing-Pointer Nanocrystalline AlN was successfully synthesized by the mechanochemical process. Black-Right-Pointing-Pointer The C/N material was formed by polymerization of DAMN during the thermal treatment process. Black-Right-Pointing-Pointer No reaction between DAMN and Al was detected during the thermal treatment method.

  4. Nb3Al Development for HEP Applications

    SciTech Connect

    Sumption, M.D.; Buta, F.; Collings, E.W.; Tomsic, M.; Phillips, J.; McFadden, K.; Wu, X

    2004-06-28

    Recent developments in Nb3Al strand for HEP applications are presented and discussed. The present state of available precursor is detailed. Two routes have been shown to lead to successful construction of MF NbAl composite wires. An extrusion method has so far produced the highest filament counts and smallest filament diameters, but requires more processing steps. A direct restack and draw approach has also been demonstrated which minimizes the number of processing steps while still leading to a high performance conductor. This latter route also allows for a lower cost per billet, potentially allowing the exploration of more process parameters.

  5. Quadrupole scattering in PrAl2

    NASA Astrophysics Data System (ADS)

    Sablik, M. J.; Pureur, P.; Creuzet, G.; Fert, A.; Levy, P. M.

    1983-10-01

    We derive the spontaneous anisotropy of the resistivity of the ferromagnetic compound PrAl2 from magnetoresistance measurements on a single crystal of PrAl2. We ascribe this spontaneous anisotropy of the resistivity to scattering of the conduction electrons by the thermal quadrupole disorder and we account for our experimental results by using the theoretical model previously developed by us. We find that quadrupole scattering gives a very important contribution to the total magnetic disorder (spin and quadrupole) resistivity but that only a small part of this quadrupole contribution is anisotropic.

  6. A Comment on Eerland et al. (2016).

    PubMed

    Hart, William

    2016-03-01

    People imagine criminal behavior in greater detail and ascribe more blame to criminals when a description of a crime is written using the imperfective verb aspect (Hart & Albarracín, 2011, Experiment 3). An initiative to reproduce these findings conducted by Eerland et al. (2016) yielded a lack of replication. Eerland et al. have suggested that the original effect was likely driven by a Type I error produced by methodological aspects of the experiment, including low sample size. Recent conceptual replications of Hart and Albarracín's effect (Sherrill, Eerland, Zwaan, & Magliano, 2015), however, might imply the effect could be contingent on sample characteristics. PMID:26993281

  7. The ALS Storage Ring RF System

    SciTech Connect

    Taylor, B.; Lo, C.C.; Baptiste, K.; Guigli, J.; Julian, J.

    1993-05-01

    The ALS Storage Ring RF System is characterized by the use of the following features: (1) High power loading of two single cell cavities. (2) The use of a tubular ceramic input window employing aperture coupling. (3) The use of waveguide filters and matchers designed for HOM absorption. (4) A comprehensive HOM monitoring system. (5) The use of waveguide water-wedge loads for the magic tee and circulator loads. The results of cavity measurements and high power tests are reported together with the performance of the system during the commissioning and operation phases of the ALS project. Plans for future window development are discussed.

  8. Complementary and Alternative Therapies in ALS

    PubMed Central

    Bedlack, Richard S.; Joyce, Nanette; Carter, Gregory T.; Pagononi, Sabrina; Karam, Chafic

    2015-01-01

    Synopsis Given the severity of their illness and lack of effective disease modifying agents, it is not surprising that most patients with ALS consider trying complementary and alternative therapies. Some of the most commonly considered alternative therapies include special diets, nutritional supplements, cannabis, acupuncture, chelation and energy healing. This chapter reviews these in detail. We also describe 3 models by which physicians may frame discussions about alternative therapies: paternalism, autonomy and shared decision making. Finally, we review a program called ALSUntangled which using shared shared decision making to review alternative therapies for ALS. PMID:26515629

  9. Surface phonon polariton characteristics of In(0.04)Al(0.06)Ga(0.90)N/AlN/Al(2)O(3) heterostructure.

    PubMed

    Ng, S S; Lee, S C; Bakhori, S K Mohd; Hassan, Z; Abu Hassan, H; Yakovlev, V A; Novikova, N N; Vinogradov, E A

    2010-05-10

    Surface phonon polariton (SPP) characteristics of In(0.04)Al(0.06)Ga(0.90)N/AlN/Al(2)O(3) heterostructure are investigated by means of p-polarized infrared (IR) attenuated total reflection spectroscopy. Two absorption dips corresponding to In(0.04)Al(0.06)Ga(0.90)N SPP modes are observed. In addition, two prominent dips and one relatively weak and broad dip corresponding to the Al(2)O(3) SPP mode, In(0.04)Al(0.06)Ga(0.90)N/Al(2)O(3) interface mode, and Al(2)O(3) bulk polariton mode, respectively, are clearly seen. No surface mode feature originating from the AlN layer is observed because it is too thin. Overall, the observations are in good agreement with the theoretical predictions. PMID:20588890

  10. Formation of gamma'-Ni3Al via the Peritectoid Reaction: gamma plus beta (+Al2O3) equals gamma'(+Al2O3)

    NASA Technical Reports Server (NTRS)

    Copland, Evan

    2008-01-01

    The activities of Al and Ni were measured using multi-cell Knudsen effusion-cell mass spectrometry (multi-cell KEMS), over the composition range 8 - 32 at.%Al and temperature range T = 1400 - 1750 K in the Ni-Al-O system. These measurements establish that equilibrium solidification of gamma'-Ni3Al-containing alloys occurs by the eutectic reaction, L (+ Al2O3) = gamma + beta (+ Al2O3), at 1640 plus or minus 1 K and a liquid composition of 24.8 plus or minus 0.2 at.%Al (at an unknown oxygen content). The {gamma + beta + Al2O3} phase field is stable over the temperature range 1633 - 1640 K, and gamma'-Ni3Al forms via the peritectiod, gamma + beta (+ Al2O3) = gamma'(+ Al2O3), at 1633 plus or minus 1 K. This behavior is inconsistent with the current Ni-Al phase diagram and a new diagram is proposed. This new Ni-Al phase diagram explains a number of unusual steady state solidification structures reported previously and provides a much simpler reaction scheme in the vicinity of the gamma'-Ni3Al phase field.

  11. Formation of gamma(sup prime)-Ni3Al via the Peritectoid Reaction: gamma + beta (+ Al2O3)=gamma(sup prime)(+ Al2O3)

    NASA Technical Reports Server (NTRS)

    Copeland, Evan

    2008-01-01

    The activities of Al and Ni were measured using multi-cell Knudsen effusion-cell mass spectrometry (multi-cell KEMS), over the composition range 8-32 at.%Al and temperature range T=1400-1750 K in the Ni-Al-O system. These measurements establish that equilibrium solidification of gamma(sup prime)-Ni3Al-containing alloys occurs by the eutectic reaction, L (+ Al2O3)=gamma + Beta(+ Al2O3), at 1640 +/- 1 K and a liquid composition of 24.8 +/- 0.2 at.%al (at an unknown oxygen content). The {gamma + Beta (+Al2O3} phase field is stable over the temperature range 1633-1640 K, and gamma(sup prime)-Ni3Al forms via the peritectoid, gamma + Beta (+ Al2O3)=gamma(sup prime) (+ Al2O3), at 1633 +/- 1 K. This behavior is consistent with the current Ni-Al phase diagram and a new diagram is proposed. This new Ni-Al phase diagram explains a number of unusual steady-state solidification structures reported previously and provides a much simpler reaction scheme in the vicinity of the gamma(sup prime)-Ni2Al phase field.

  12. 26Al+p elastic and inelastic scattering reactions and galactic abundances of 26Al

    NASA Astrophysics Data System (ADS)

    Pittman, S. T.; Bardayan, D. W.; Chae, K. Y.; Chipps, K. A.; Jones, K. L.; Kozub, R. L.; Matei, C.; Matos, M.; Moazen, B. H.; Nesaraja, C. D.; O'Malley, P. D.; Pain, S. D.; Parker, P. D.; Peters, W. A.; Shriner, J. F., Jr.; Smith, M. S.

    2012-06-01

    Galactic 26Al is the first radioactive nucleus to be positively identified by γ-ray astronomy with detection of the 1.809 MeV γ ray associated with its decay. This nucleus is destroyed in astrophysical environments in the 26Al(p,γ)27Si and inelastic 26Al+p scattering reactions where properties of 27Si levels determine reaction rates. To investigate these properties, elastic and inelastic 26Al+p scattering reactions were measured between Ec.m. = 0.5-1.5 MeV at the Holifield Radioactive Ion Beam Facility (HRIBF) at Oak Ridge National Laboratory (ORNL). A candidate for a new resonance in the 26Al(p,γ)27Si reaction was identified. Upper limits were also set on the strengths of postulated resonances and on the cross section of the inelastic reaction, but there is little effect on current reaction rate calculations.

  13. Al/sub 2/O/sub 3/ adherence on CoCrAl alloys

    SciTech Connect

    Kingsley, L.M.

    1980-04-01

    Adherence of protective oxides on NiCrAl and CoCrAl superalloys has been promoted by a dispersion of a highly oxygen reactive element or its oxide being produced within the protection system. Two aspects of this subject are investigated here: the use of Al/sub 2/O/sub 3/ as both the dispersion and protective oxide; and the production of an HfO/sub 2/ dispersion while simultaneously aluminizing the alloy. It was found that an Al/sub 2/O/sub 3/ dispersion will act to promote the adherence of an external scale of Al/sub 2/O/sub 3/ to a degree comparable to previously tested dispersions and an HfO/sub 2/ dispersion comparable to that produced by a Rhines pack treatment is produced during aluminization.

  14. CVD Fiber Coatings for Al2O3/NiAl Composites

    NASA Technical Reports Server (NTRS)

    Boss, Daniel E.

    1995-01-01

    While sapphire-fiber-reinforced nickel aluminide (Al2O3/NiAl) composites are an attractive candidate for high-temperature structures, the significant difference in the coefficient of thermal expansion between the NiAl matrix and the sapphire fiber creates substantial residual stresses in the composite. This study seeks to produce two fiber-coating systems with the potential to reduce the residual stresses in the sapphire/NiAl composite system. Chemical vapor deposition (CVD) was used to produce both the compensating and compliant-fiber coatings for use in sapphire/NiAl composites. A special reactor was designed and built to produce the FGM and to handle the toxic nickel precursors. This process was successfully used to produce 500-foot lengths of fiber with coating thicknesses of approximately 3 microns, 5 microns, and 10 microns.

  15. Temperature dependence of the activity of Al in dilute Ni(Al) solid solutions

    SciTech Connect

    Jiang Yong; Smith, J. R.; Evans, A. G.

    2006-12-01

    Activities of dilute Al solid solutions in Ni are determined from a first-principles approach. Both thermal lattice vibration and electronic contributions to free energies are considered and compared. Vibrational contributions tend to dominate the temperature dependencies of the free energies, though electron thermal effects are significant. Calculations show opposing temperature trends for the formation enthalpies and entropies, leading to a partial cancellation of their role in the overall energetics. Nevertheless, their remaining temperature effects are strong. Over the temperature range, 400 KAl activity coefficient varies by 15 orders of magnitude, due to the relative strength of Al-Ni and Al-Al bonds. The Ni activity coefficient only varies less than 4% over the same range. Calculational results compare well with available experimental data. The thermodynamic principles elucidated from the calculations are used to provide a fundamental interpretation.

  16. Preparation, structure and mechanical properties of RuAl and (Ru,Ni)Al alloys

    SciTech Connect

    Sabariz, A.L.R.; Taylor, G.

    1997-12-31

    The intermetallic compound, RuAl with B2 CsCl type structure, has been shown to possess room-temperature toughness and plasticity. NiAl also forms a B2 compound and it is claimed that a pseudo-binary compound, (Ru,Ni)Al, may be formed because the difference in lattice parameter between the two binary phases is slight. In this work a study has been made of the mechanical properties of some polycrystalline compounds, across the RuAl-(Ru,Ni)Al pseudo-binary, prepared from high-purity elemental powders. Compressive yield stresses were measured between room-temperature and 900 C, and the mechanisms of plastic flow are discussed in relation to the dislocation structures observed by TEM. Hot-microhardness tests were made to provide an indication of the effect of solid-solution hardening.

  17. In situ microscopy of rapidly heated nano-Al and nano-Al/WO3 thermites

    NASA Astrophysics Data System (ADS)

    Sullivan, Kyle T.; Chiou, Wen-An; Fiore, Richard; Zachariah, Michael R.

    2010-09-01

    The initiation and reaction mechanism of nano-Al and nano-Al thermites in rapid heating environments is investigated in this work. A semiconductor-based grid/stage was used, capable of in situ heating of a sample from room temperature to 1473 K, and at a rate of 106 K/s, inside an electron microscope. Nano-Al was rapidly heated in a transmission electron microscope, and before and after images indicate that the aluminum migrates through the shell, consistent with a diffusion-based mechanism. A nano-Al/WO3 composite was then heated in a scanning electron microscope. The results indicate that a reactive sintering mechanism is occurring for the nano-Al/WO3 thermite, as the products are found to be in surface contact and significantly deformed after the heating pulse.

  18. 1300 K compressive properties of a reaction milled NiAl-AlN composites

    NASA Technical Reports Server (NTRS)

    Whittenberger, J. Daniel; Arzt, Eduard; Luton, Michael J.

    1990-01-01

    When B2 crystal-structure nickel aluminide is subjected to high-intensity mechanical ball milling in a liquid nitrogen bath, or 'cryomilling', an NiAl composite is obtained which contains about 10 vol pct AlN particles. This composition arises from the incorporation of N during cryomilling; during subsequent thermomechanical processing, the N reacts with Al. While compressive testing of extruded or isostatically pressed specimens at 1300 K indicated that strength at relatively fast strain rates is slightly dependent on consolidation method, slower strain rates indicate no clear dependency on densification technique: four different consolidation methods were found to yield similar creep strengths. The creep properties of NiAl-AlN are similar to those of the single-crystal Ni-base superalloy NASAIR 100.

  19. Effect of stress on the Al composition evolution in AlGaN grown using metal organic vapor phase epitaxy

    NASA Astrophysics Data System (ADS)

    He, Chenguang; Qin, Zhixin; Xu, Fujun; Zhang, Lisheng; Wang, Jiaming; Hou, Mengjun; Zhang, Shan; Wang, Xinqiang; Ge, Weikun; Shen, Bo

    2016-05-01

    Two series of AlGaN samples with different stresses were designed to investigate the effect of stress on the Al composition. X-ray diffraction reciprocal space mapping (XRD RSM) demonstrated that the AlGaN epilayers with different stresses have large Al composition differences despite the same growth conditions. The largest Al composition difference reached up to 21.3%, which was also confirmed using secondary ion mass spectroscopy (SIMS). This result is attributed to a large stress discrepancy in the AlGaN epilayers. Finally, the dependences of the solid-phase Al composition on the gas-phase Al composition under different stresses were systematically analyzed.

  20. Equilibrium point defects in intermetallics with the [ital B]2 structure: NiAl and FeAl

    SciTech Connect

    Fu, C.L.; Ye, Y.; Yoo, M.H. ); Ho, K.M. )

    1993-09-01

    Equilibrium point defects and their relation to the contrasting mechanical behavior of NiAl and FeAl are investigated. For NiAl, the defect structure is dominated by two types of defects---monovacancies on the Ni sites and substitutional antisite defects on the Al sites. The defect structure of FeAl differs from that of NiAl in the occurrence of antisite defects at the transition-metal sites for Al-rich alloys and the tendency for vacancy clustering. The strong ordering (and brittleness) of NiAl is attributed mainly to the difference in atomic size between constituent atoms.

  1. Wear characteristics of Al-AlN composites produced in-situ by nitrogenation

    NASA Astrophysics Data System (ADS)

    Pradhan, S.; Jena, S. K.; Patnaik, S. C.; Swain, P. K.; Majhi, J.

    2015-02-01

    In the present scenario most of the parts used in automobile and aerospace industries are made of composites. Aluminium metal has a very high strength to weight ratio. Al-AlN metal matrix composites have excellent mechanical properties like good wear resistance, high hardness and high strength to weight ratio which are obtained from low density of aluminium and high hardness and wear resistance of AlN. Therefore, use of Al-AlN MMC leads to advantages in automobile industries as it reduces fuel consumption and gives better structural strength. The composites can be produced ex-situ by introducing AlN as reinforcement into the metal matrix and in- situ by nitrogenation process. In the present process Al-AlN composites were fabricated by treating molten aluminium with a mixture of CaO and NH4Cl and held at temperature range at 750-930°C and then cast into a metal mould. Addition of CaO to NH4Cl is found to have a more pronounced effect as a nitrogenation agent in comparison with NH4Cl in the molten aluminium in the temperature range of 700- 1000°C. Castings of aluminium and Al-AlN composites were prepared by mixing different ratios of aluminium and NH4Cl, at different casting temperatures and holding time. Wear resistance and hardness of the samples were determined, and microstructure studies were carried out. The composite formed using higher amount of NH4Cl had higher hardness and wear resistance.

  2. Microstructure of Ni-Al powder and Ni-Al composite coatings prepared by twin-wire arc spraying

    NASA Astrophysics Data System (ADS)

    Wang, Ji-xiao; Wang, Gui-xian; Liu, Jing-shun; Zhang, Lun-yong; Wang, Wei; Li, Ze; Wang, Qi-xiang; Sun, Jian-fei

    2016-07-01

    Ni-Al powder and Ni-Al composite coatings were fabricated by twin-wire arc spraying (TWAS). The microstructures of Ni-5wt%Al powder and Ni-20wt%Al powder were characterized by scanning electronic microscopy (SEM) and energy dispersive spectroscopy (EDS). The results showed that the obtained particle size ranged from 5 to 50 μm. The morphology of the Ni-Al powder showed that molten particles were composed of Ni solid solution, NiAl, Ni3Al, Al2O3, and NiO. The Ni-Al phase and a small amount of Al2O3 particles changed the composition of the coating. The microstructures of the twin-wire-arc-sprayed Ni-Al composite coatings were characterized by SEM, EDS, X-ray diffraction (XRD), and transmission electron microscopy (TEM). The results showed that the main phase of the Ni-5wt%Al coating consisted of Ni solid solution and NiAl in addition to a small amount of Al2O3. The main phase of the Ni-20wt%Al coating mainly consisted of Ni solid solution, NiAl, and Ni3Al in addition to a small amount of Al and Al2O3, and NiAl and Ni3Al intermetallic compounds effectively further improved the final wear property of the coatings. TEM analysis indicated that fine spherical NiAl3 precipitates and a Ni-Al-O amorphous phase formed in the matrix of the Ni solid solution in the original state.

  3. Thermodynamics and Kinetics of the Formation of Al2O3/ MgAl2O4/MgO in Al-Silica Metal Matrix Composite

    NASA Astrophysics Data System (ADS)

    Sreekumar, V. M.; Ravi, K. R.; Pillai, R. M.; Pai, B. C.; Chakraborty, M.

    2008-04-01

    The formation of Al2O3, MgAl2O4, and MgO has been widely studied in different Al base metal matrix composites, but the studies on thermodynamic aspects of the Al2O3/ MgAl2O4/MgO phase equilibria have been limited to few systems such as Al/Al2O3 and Al/SiC. The present study analyzes the Al2O3/MgAl2O4 and MgAl2O4/MgO equilibria with respect to the temperature and the Mg content in Al/SiO2 system using an extended Miedema model. There is a linear and parabolic variation in Mg with respect to the temperature for MgAl2O4/MgO and Al2O3/MgAl2O4 equilibria, respectively, and the influence of Si and Cu in the two equilibria is not appreciable. The experimental verification has been limited to MgAl2O4/MgO equilibria due to the high Mg content (≥0.5 wt pct) required for composite processing. The study has been carried out on two varieties of Al/SiO2 composites, i.e., Al/Silica gel and Al/Micro silica processed by liquid metallurgy route (stir casting route). MgO is found to be more stable compared to MgAl2O4 at Mg levels ≥5 and 1 wt pct in Al/Silica gel and Al/Micro silica composites, respectively, at 1073 K. MgO is also found to be more stable at lower Mg content (3 wt pct) in Al/Silica gel composite with decreasing particle size of silica gel from 180 micron to submicron and nanolevels. The MgO to MgAl2O4 transformation has taken place through a series of transition phases influenced by the different thermodynamic and kinetic parameters such as holding temperature, Mg concentration in the alloy, holding time, and silica particle size.

  4. Ternary Dy-Er-Al magnetic refrigerants

    DOEpatents

    Gschneidner, K.A. Jr.; Takeya, Hiroyuki

    1995-07-25

    A ternary magnetic refrigerant material comprising (Dy{sub 1{minus}x}Er{sub x})Al{sub 2} for a magnetic refrigerator using the Joule-Brayton thermodynamic cycle spanning a temperature range from about 60K to about 10K, which can be adjusted by changing the Dy to Er ratio of the refrigerant. 29 figs.

  5. Joint SSRTNet/ALS-MES Workshop report

    SciTech Connect

    Shuh, David; Van Hove, Michel

    2001-11-30

    This joint workshop brought together experimentalists and theorists interested in synchrotron radiation and highlighted subjects relevant to molecular environmental science (MES). The strong mutual interest between the participants resulted in joint sessions on the first day, followed by more specialized parallel sessions on the second day. Held in conjunction with the Advanced Light Source (ALS) Users' Association Annual Meeting at the Lawrence Berkeley National Laboratory (Berkeley Lab), the Synchrotron Radiation Research Theory Network (SRRTNet) workshop was co-organized by Michel Van Hove (Berkeley Lab and University of California, Davis) and Andrew Canning (Berkeley Lab), while David Shuh (Berkeley Lab) organized the ALS-MES workshop. SRRTNet is a global network that promotes the interaction of theory and experiment (http://www.cse.clrc.ac.uk/Activity/SRRTnet). The ALS-MES project is constructing Beamline 11.0.2.1-2, a new soft x-ray beamline for MES investigations at photon energies from 75 eV to 2 keV, to provide photons for wet spectroscopy end stations and an upgraded scanning transmission x-ray microscope (STXM). The ALS-MES beamline and end stations will be available for users in the late fall of 2002.

  6. Electron impact exctation of Al X

    NASA Astrophysics Data System (ADS)

    Aggarwal, Kanti; Keenan, Francis

    2013-05-01

    Emission lines of Al ions, including Al X, are important for the modeling and diagnostics of lasing, fusion and astrophysical plasmas, for which atomic data are required for a variety of parameters, such as energy levels, radiative rates (A- values), and excitation rates or equivalently the effective collision strengths (Υ), which are obtained from the electron impact collision strengths (Ω). Experimentally, energy levels are available for Al X on the NIST website, but there is paucity for accurate collisional atomic data. Therefore, here we report a complete set of results (namely energy levels, radiative rates, and effective collision strengths) for all transitions among the lowest 98 levels of Al X. These levels belong to the (1s2) 2s2, 2s2p, 2p2, 2s3 l, 2p3 l, 2s4 l, and 2p4 l configurations. Finally, we also report the A- values for four types of transitions, namely electric dipole (E1), electric quadrupole (E2), magnetic dipole (M1), and magnetic quadrupole (M2), because these are also required for plasma modeling. For our calculations of wavefunctions, we have adopted the fully relativistic GRASP code, and for the calculations of Ω, the Dirac atomic R-matrix code (DARC) of PH Norrington and IP Grant. Additionally, parallel ca

  7. Kinematics of Disease Progression in Bulbar ALS

    ERIC Educational Resources Information Center

    Yunusova, Yana; Green, Jordan R.; Lindstrom, Mary J.; Ball, Laura J.; Pattee, Gary L.; Zinman, Lorne

    2010-01-01

    The goal of this study was to investigate the deterioration of lip and jaw movements during speech longitudinally in three individuals diagnosed with bulbar amyotrophic lateral sclerosis (ALS). The study was motivated by the need to understand the relationship between physiologic changes in speech movements and clinical measures of speech…

  8. Quantum Criticality in YFe2Al10

    NASA Astrophysics Data System (ADS)

    Gannon, William; Wu, Liusuo; Zaliznyak, Igor; Qiu, Yiming; Rodriguez-Rivera, Jose; Aronson, Meigan

    Quantum criticality has been studied in many systems, but there are few systems where observed scaling can be unified with a critical free energy F, or where the critical exponents form the basis for QC universality classes. We have identified a new layered material YFe2Al10 that shows remarkably strong QC behavior, where the scaling properties of the magnetic susceptibility and specific heat are consistent with the same F. Recent neutron scattering results paint a remarkable picture of the QC fluctuations in YFe2Al10. In contrast to classical transitions, where fluctuations are relatively long ranged and inelastic scattering is observed at a magnetic zone center, in YFe2Al10 the scattering is independent of wave vector in the critical plane, indicating that the fluctuations are spatially localized, while out of plane scattering indicates that the interplaner interactions are restricted to nearest neighbors. The dynamical susceptibility χ'' ~=E-2 , and is wholly temperature independent, indicating that E/T scaling is present, the signature of QC fluctuations. These results hint that the the criticality in YFe2Al10 is local, which until now has only been found in a few f-electron based compounds.

  9. Kinematics of Disease Progression in Bulbar ALS

    PubMed Central

    Yunusova, Yana; Green, Jordan; Lindstrom, Mary; Ball, Laura; Pattee, Gary; Zinman, Lorne

    2009-01-01

    The goal of this study was to investigate the deterioration of lip and jaw movements during speech longitudinally in three individuals diagnosed with bulbar Amyotrophic Lateral Sclerosis (ALS). The study was motivated by the need to understand the relationship between physiologic changes in speech movements and clinical measures of speech performance such as speaking rate and speech intelligibility. Movements of the lip and jaw were quantified with respect to their size (i.e., path distance measure), speed, and duration. The data revealed several changes in lip and jaw movement that coincided with ALS progression. In two out of three speakers, the changes in measures of path distance and speed anticipated the drop in speech intelligibility by approximately 3 months. With disease progression, increases in movement duration coincided with declines in speech intelligibility. Overall, the movement measures appeared to be sensitive to disease progression in ALS. Learning outcomes By the end of the manuscript, the reader should be able to: (1) describe the changes that occur in articulatory movements of the jaw and lower lip in ALS; (2) understand the relationship between physiologic measures of movement and speech intelligibility and speaking rate; (3) identify critical points in the disease progression and understand which quantitative measures reveal the state of the bulbar system at these time points. PMID:19683250

  10. Cryptanalysis on Cheng et al. protocol

    NASA Astrophysics Data System (ADS)

    Thakur, Tejeshwari

    2016-06-01

    Deployment of new node in any wireless sensor network is a sensitive task. This is the reason why, an Access Control Protocol is required in WSN. In this paper, we demonstrate that Access Control Protocol proposed by Cheng et al.[1] for Wireless Sensor Network is insecure. The reason is that this protocol fails to resist the active attack.

  11. U-ALS: A Ubiquitous Learning Environment

    ERIC Educational Resources Information Center

    Piovesan, Sandra Dutra; Passerino, Liliana Maria; Medina, Roseclea Duarte

    2012-01-01

    The diffusion of the use of the learning virtual environments presents a great potential for the development of an application which meet the necessities in the education area. In view of the importance of a more dynamic application and that can adapt itself continuously to the students' necessities, the "U-ALS" (Ubiquitous Adapted Learning…

  12. Thermal mixing of Al-Fe multilayers

    NASA Astrophysics Data System (ADS)

    Meyer, M.; Mendoza Zélis, L.; Sánchez, F. H.; Traverse, A.

    1994-12-01

    Al-Fe multilayers have been mixed by thermal treatment and their evolution followed by conversion electron Mössbauer spectroscopy. The initial and final states have been characterized by Rutherford backscattering spectrometry. The results are compared with those previously obtained in the ion beam mixing of similar systems.

  13. Bierman {ital et al.}Reply:

    SciTech Connect

    Bierman, J.D.; Chan, P.; Liang, J.F.; Kelly, M.P.; Sonzogni, A.A.; Vandenbosch, R.

    1997-05-01

    reply to the Comment by C.H.Dasso et al., Phys. Rev. Lett. 78,XXX(1997). A Reply to the Comment by C.H. Dasso and J. Fern{acute a}ndez-Niello. {copyright} {ital 1997} {ital The American Physical Society}

  14. Ternary Dy-Er-Al magnetic refrigerants

    DOEpatents

    Gschneidner, Jr., Karl A.; Takeya, Hiroyuki

    1995-07-25

    A ternary magnetic refrigerant material comprising (Dy.sub.1-x Er.sub.x)Al.sub.2 for a magnetic refrigerator using the Joule-Brayton thermodynamic cycle spanning a temperature range from about 60K to about 10K, which can be adjusted by changing the Dy to Er ratio of the refrigerant.

  15. Al/Cl2 molten salt battery

    NASA Technical Reports Server (NTRS)

    Giner, J.

    1972-01-01

    Molten salt battery has been developed with theoretical energy density of 5.2 j/kg (650 W-h/lb). Battery, which operates at 150 C, can be used in primary mode or as rechargeable battery. Battery has aluminum anode and chlorine cathode. Electrolyte is mixture of AlCl3, NaCl, and some alkali metal halide such as KCl.

  16. Correction to Rothermund et al. (2005)

    ERIC Educational Resources Information Center

    Rothermund, Klaus; Wentura, Dirk; De Houwer, Jan

    2005-01-01

    This article reports an error in the article "Retrieval of Incidental Stimulus-Response Associations as a Source of Negative Priming" by Rothermund et al. ("Journal of Experimental Psychology: Learning, Memory, and Cognition," Vol 31(3) May 2005, 482-495). Table 1 (p. 484) was incorrectly typeset. The correct layout is provided. (The following…

  17. 75 FR 26814 - Alabama Disaster #AL-00031

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-05-12

    ... From the Federal Register Online via the Government Publishing Office SMALL BUSINESS ADMINISTRATION Alabama Disaster AL-00031 AGENCY: U.S. Small Business Administration. ACTION: Notice. SUMMARY: This is a Notice of the Presidential declaration of a major disaster for Public Assistance Only for...

  18. 76 FR 29810 - Alabama Disaster #AL-00037

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-05-23

    ... From the Federal Register Online via the Government Publishing Office SMALL BUSINESS ADMINISTRATION Alabama Disaster AL-00037 AGENCY: U.S. Small Business Administration. ACTION: Notice. SUMMARY: This is a Notice of the Presidential declaration of a major disaster for Public Assistance Only for...

  19. 75 FR 474 - Alabama Disaster #AL-00026

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-01-05

    ... From the Federal Register Online via the Government Publishing Office SMALL BUSINESS ADMINISTRATION Alabama Disaster AL-00026 AGENCY: U.S. Small Business Administration. ACTION: Notice. SUMMARY: This is a Notice of the Presidential declaration of a major disaster for Public Assistance Only for...

  20. 78 FR 4967 - Alabama Disaster #AL-00046

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-01-23

    ... From the Federal Register Online via the Government Publishing Office SMALL BUSINESS ADMINISTRATION Alabama Disaster AL-00046 AGENCY: U.S. Small Business Administration. ACTION: Notice. SUMMARY: This is a notice of an Administrative declaration of a disaster for the State of ALABAMA dated...

  1. 76 FR 27141 - Alabama Disaster # AL-00036

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-05-10

    ... From the Federal Register Online via the Government Publishing Office SMALL BUSINESS ADMINISTRATION Alabama Disaster AL-00036 AGENCY: U.S. Small Business Administration. ACTION: Notice. SUMMARY: This is a Notice of the Presidential declaration of a major disaster for the State of Alabama...

  2. 78 FR 22361 - Alabama Disaster #AL-00049

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-04-15

    ... From the Federal Register Online via the Government Publishing Office SMALL BUSINESS ADMINISTRATION Alabama Disaster AL-00049 AGENCY: U.S. Small Business Administration. ACTION: Notice. SUMMARY: This is a notice of an Administrative declaration of a disaster for the State of Alabama dated...

  3. 75 FR 26813 - Alabama Disaster #AL-00029

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-05-12

    ... From the Federal Register Online via the Government Publishing Office SMALL BUSINESS ADMINISTRATION Alabama Disaster AL-00029 AGENCY: Small Business Administration. ACTION: Notice. SUMMARY: This is a Notice of the Presidential declaration of a major disaster for the State of Alabama...

  4. 77 FR 60003 - Alabama Disaster #AL-00044

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-10-01

    ... From the Federal Register Online via the Government Publishing Office SMALL BUSINESS ADMINISTRATION Alabama Disaster AL-00044 AGENCY: U.S. Small Business Administration. ACTION: Notice. SUMMARY: This is a Notice of the Presidential declaration of a major disaster for Public Assistance Only for...

  5. 77 FR 7227 - Alabama Disaster #AL-00040

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-02-10

    ... From the Federal Register Online via the Government Publishing Office SMALL BUSINESS ADMINISTRATION Alabama Disaster AL-00040 AGENCY: U.S. Small Business Administration. ACTION: Notice. SUMMARY: This is a Notice of the Presidential declaration of a major disaster for the State of Alabama...

  6. 75 FR 1420 - Alabama Disaster # AL-00025

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-01-11

    ... From the Federal Register Online via the Government Publishing Office SMALL BUSINESS ADMINISTRATION Alabama Disaster AL-00025 AGENCY: U.S. Small Business Administration. ACTION: Notice. SUMMARY: This is a notice of an Administrative declaration of a disaster for the State of Alabama dated...

  7. 76 FR 62481 - Incapital LLC, et al.

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-10-07

    ... From the Federal Register Online via the Government Publishing Office SECURITIES AND EXCHANGE COMMISSION Incapital LLC, et al.; Notice of Application September 30, 2011. AGENCY: Securities and Exchange Commission (``Commission''). ACTION: Notice of application for an order under section 12(d)(1)(J) of...

  8. 78 FR 26100 - Alabama Disaster #AL-00050

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-05-03

    ... From the Federal Register Online via the Government Publishing Office SMALL BUSINESS ADMINISTRATION Alabama Disaster AL-00050 AGENCY: U.S. Small Business Administration. ACTION: Notice. SUMMARY: This is a notice of an Administrative declaration of a disaster for the State of Alabama dated...

  9. SPI measurements of Galactic 26Al

    NASA Astrophysics Data System (ADS)

    Diehl, R.; Knödlseder, J.; Lichti, G. G.; Kretschmer, K.; Schanne, S.; Schönfelder, V.; Strong, A. W.; von Kienlin, A.; Weidenspointner, G.; Winkler, C.; Wunderer, C.

    2003-11-01

    The precision measurement of the 1809 keV gamma-ray line from Galactic 26Al is one of the goals of the SPI spectrometer on INTEGRAL with its Ge detector camera. We aim for determination of the detailed shape of this gamma-ray line, and its variation for different source regions along the plane of the Galaxy. Data from the first part of the core program observations of the first mission year have been inspected. A clear detection of the 26Al line at =~ 5-7 sigma significance demonstrates that SPI will deepen 26Al studies. The line intensity is consistent with expectations from previous experiments, and the line appears narrower than the 5.4 keV FWHM reported by GRIS, more consistent with RHESSI's recent value. Only preliminary statements can be made at this time, however, due to the multi-component background underlying the signal at =~ 40 times higher intensity than the signal from Galactic 26Al.

  10. Al-Ghazali on Moral Education

    ERIC Educational Resources Information Center

    Alavi, Hamid Reza

    2007-01-01

    Al-Ghazali (1058-1111 CE) is probably the most influential scholar, philosopher, theologian, legal expert, religious reformer and mystic in the history of Islam. Although he wrote extensively about education, and particularly about moral education, this writing is scattered through a number of different works and has received less scholarly…

  11. Hydrogen Solubility in Al-bearing Perovskite

    NASA Astrophysics Data System (ADS)

    Watson, H. C.; Krawczynski, M. J.; Fei, Y.

    2005-12-01

    It is generally accepted that silicate perovskite is the dominant mineral in the Earth's lower mantle. Previous studies have been completed to determine the physical and chemical characteristics of the pure end-member MgSiO3. Recent studies have shown that the addition of Al to MgSiO3 can have a significant effect on the material properties of the mineral, such as compressibility, and defect structure, as well as a great potential to dissolve water. We have synthesized Al-bearing perovskite samples under hydrous conditions in a multi-anvil apparatus at pressures ranging from 23-26 GPa and 1800oC. The starting materials consisted of brucite and silica powders mixed together and finely ground in a 1:1 molar ratio, with subsequent addition of Al2O3 powder at 2wt% intervals from 0%-6%. The mixed powders were tightly packed in Au capsules, housed in BN sleeves, and loaded into standard 8/3 multi-anvil assemblies. The experiments were brought to the appropriate pressure conditions for solubility of the different Al2O3 contents. The resulting perovskite crystals range in size from <20 microns to >100 microns in size. Their major element chemistry has been characterized by EPMA, and the H content of some samples has been measured by secondary ion mass spectrometry using a 6f Cameca ion microprobe and is substantial (>1200ppm in some samples). In this study, we correlate H content in the perovskites with Al concentration, and discussion follows on what effects this may have on potential substitution mechanisms, and correlated formation of oxygen vacancies, as well as water storage in the mantle, oxygen diffusion, and the potential of an oxygen ionic diffusion contribution to electrical conductivity in the mantle.

  12. Calculation of the structure of the Al(331) stepped surface

    SciTech Connect

    Nelson, J.S.; Feibelman, P.J. )

    1992-04-06

    Car-Parinello-like calculations have been used to compute the relaxation of the Al(331) surface, with results that are in remarkable agreement with the low-energy electron-diffraction analysis of Adams and So( )renson. Rapid screening of the steps on Al(331) is illustrated by comparing its charge density and relaxations to those of Al(110) and Al(111).

  13. Some TEM observations of Al2O3 scales formed on NiCrAl alloys

    NASA Technical Reports Server (NTRS)

    Smialek, J.; Gibala, R.

    1979-01-01

    The microstructural development of Al2O3 scales on NiCrAl alloys has been examined by transmission electron microscopy. Voids have been observed within grains in scales formed on a pure NiCrAl alloy. Both voids and oxide grains grew measurably with oxidation time at 1100 C. The size and amount of porosity decreased towards the oxide-metal growth interface. It was postulated that the voids resulted from an excess number of oxygen vacancies near the oxide-metal interface. Short-circuit diffusion paths were discussed in reference to current growth stress models for oxide scales. Transient oxidations of pure, Y-doped, and Zr-doped NiCrAl was also examined. Oriented alpha-(Al,Cr)2O3 and Ni(Al,Cr)2O4 scales often coexisted in layered structures on all three alloys. Close-packed oxygen planes and directions in the corundum and spinel layers were parallel. The close relationships between oxide layers provided a gradual transition from initial transient scales to steady state Al2O3 growth.

  14. High noise suppression using magnetically isotropic (CoFe-AlN)/(AlN) multilayer films

    NASA Astrophysics Data System (ADS)

    Kijima, Hanae; Ohnuma, Shigehiro; Masumoto, Hiroshi; Shimada, Yutaka; Endo, Yasushi; Yamaguchi, Masahiro

    2015-05-01

    Magnetically isotropic (CoFe-AlN)n/(AlN)n+1 multilayer films, in which the number of CoFe-AlN magnetic layers n ranged from 1 to 27, were prepared by radio frequency sputtering to achieve noise suppression at gigahertz frequencies. The soft CoFe-AlN magnetic layers consisted of nanometer-sized CoFe ferromagnetic grains embedded in an insulating AlN amorphous matrix, while the insulating AlN layers comprised AlN columnar crystals. All films showed a similar frequency dependence of permeability and ferromagnetic resonance of 1.7 GHz. Noise suppression was evaluated using a microstrip line as a noise source by determining the in-line conductive loss and the near-field intensity picked up by magnetic field detective probes. High noise suppression effects were observed in every direction in the film plane. Maximum noise suppression values amounted to 60% for the in-line conductive loss and -20 dB for the magnetic near-field intensity at around 1.7 GHz in the 27-layer film. These high-frequency noise suppression levels may be attributed to eddy current losses and ferromagnetic resonance.

  15. Electrical defects in AlGaN and InAlN

    NASA Astrophysics Data System (ADS)

    Johnstone, D.; Leach, Jacob H.; Kovalskii, Vladimir A.; Fan, Qian; Xie, Jingqiao; Morkoç, Hadis

    2009-02-01

    Compound semiconductors based on GaN have multiple functional applications. Useful compositions include GaN, and ternary and quaternary compositions of (AlGaIn)N. Defects arising from lattice mismatch, point defects, or impurities may act as electrical trapping centers and degrade device efficiency. Current-voltage, capacitance-voltage, thermal admittance spectroscopy (TAS), and deep level transient spectroscopy (DLTS) measurements are applied to characterize the defects in Al0.40Ga0.80N and In0.18Al0.82N in this report. Broad peaks with a shoulder at high temperature dominate the DLTS spectra in each of the materials. An acceptor trap associated with a dislocation appears at 340 K in AlGaN. The defect has an energy of 0.2 eV and capture cross section of 10-21 cm2. A second trap at 0.35 eV, 10-14 cm2 appears in the TAS measurements in addition to the trap at 0.2 eV. Defects in InAlN are dominated by a peak near 150 K. Two traps appear in the TAS measurements. Both traps in the InAlN are acceptors, based on a lack of field dependent emission rates using double pulse DLTS (DDLTS). The two energy levels in InAlN appear to be coupled, with only one state occupied at a time.

  16. Thermoelectric Powers of Cells With NaF-AlF3-Al2O3 Melts

    NASA Astrophysics Data System (ADS)

    Flem, Belinda E.; Xu, Qian; Kjelstrup, Signe; Sterten, Åsmund

    2001-07-01

    A thermodynamic description of the Peltier heat at the aluminum and the oxygen electrode in the system NaF-AlF3-Al2O3 is given. The thermoelectric power in melts with molar ratios n NaF/n AlF3 from 3.0 to 1.0, saturated with alumina are measured. Seebeck coefficients for molten fluoride electrolytes saturated with alumina, electrolytes that are relevant for aluminum electrowinning electrolysis cells, are reported. The results allow determinations of Peltier heats of aluminum, oxygen and carbon electrodes in NaF-AlF3 electrolytes saturated with alumina. For molar ratios of n NaF/n AlF3 between 2.6 and 1.2, there is a Peltier heating of the aluminum cathode. This heating is in the same order of magnitude as the electrolyte Joule heat, when the current density is 0.7 A cm-2. For molar ratio n NaF/n AlF3 equal to 1.0 the Peltier effect at the aluminum electrode approaches zero. From theoretical considerations we expect a drop also for molar ratio 3.0. For the anode we report a Peltier cooling that is larger than the heat produced by the anodic overvoltage, in melts with NaF/AlF3 molar ratio between 2.6 and 1.2 saturated with alumina.

  17. Some TEM observations of Al2O3 scales formed on NiCrAl alloys

    NASA Technical Reports Server (NTRS)

    Smialek, J.; Gibala, R.

    1979-01-01

    The microstructural development of Al2O3 scales on NiCrAl alloys has been examined by transmission electron microscopy. Voids were observed within grains in scales formed on a pure NiCrAl alloy. Both voids and oxide grains grew measurably with oxidation time at 1100 C. The size and amount of porosity decreased towards the oxide-metal growth interface. The voids resulted from an excess number of oxygen vacancies near the oxidemetal interface. Short-circuit diffusion paths were discussed in reference to current growth stress models for oxide scales. Transient oxidation of pure, Y-doped, and Zr-doped NiCrAl was also examined. Oriented alpha-(Al, Cr)2O3 and Ni(Al, Cr)2O4 scales often coexisted in layered structures on all three alloys. Close-packed oxygen planes and directions in the corundum and spinel layers were parallel. The close relationship between oxide layers provided a gradual transition from initial transient scales to steady state Al2O3 growth.

  18. Ferromagnetic ordering in NpAl2: Magnetic susceptibility and 27Al nuclear magnetic resonance

    NASA Astrophysics Data System (ADS)

    Martel, L.; Griveau, J.-C.; Eloirdi, R.; Selfslag, C.; Colineau, E.; Caciuffo, R.

    2015-08-01

    We report on the magnetic properties of the neptunium based ferromagnetic compound NpAl2. We used magnetization measurements and 27Al NMR spectroscopy to access magnetic features related to the paramagnetic and ordered states (TC=56 K). While very precise DC SQUID magnetization measurements confirm ferromagnetic ordering, they show a relatively small hysteresis loop at 5 K reduced with a coercive field HCo~3000 Oe. The variable offset cumulative spectra (VOCS) acquired in the paramagnetic state show a high sensitivity of the 27Al nuclei spectral parameters (Knight shifts and line broadening) to the ferromagnetic ordering, even at room temperature.

  19. Revisiting Deng et al.'s Multiparty Quantum Secret Sharing Protocol

    NASA Astrophysics Data System (ADS)

    Hwang, Tzonelih; Hwang, Cheng-Chieh; Yang, Chun-Wei; Li, Chuan-Ming

    2011-09-01

    The multiparty quantum secret sharing protocol [Deng et al. in Chin. Phys. Lett. 23: 1084-1087, 2006] is revisited in this study. It is found that the performance of Deng et al.'s protocol can be much improved by using the techniques of block-transmission and decoy single photons. As a result, the qubit efficiency is improved 2.4 times and only one classical communication, a public discussion, and two quantum communications between each agent and the secret holder are needed rather than n classical communications, n public discussions, and 3n/2 quantum communications required in the original scheme.

  20. A 25-year replication of Katz et al.'s (1988) metaphor norms.

    PubMed

    Campbell, Spencer J; Raney, Gary E

    2016-03-01

    Research in metaphor processing has made extensive use of the normed metaphor database created by Katz, Paivio, Marschark, & Clark (Metaphor and Symbolic Activity, 3, 191-214, 1988). Because of the plasticity of figurative language, we conducted a renorming of selected metaphors from the database on a new student population. Correlations between Katz et al.'s and the present data showed that the pattern of responses has remained highly consistent across time and populations. The consistency of the normative ratings allows us to be confident in future research that will use the Katz et al. collection. PMID:25772671

  1. Al-based metal matrix composites reinforced with nanocrystalline Al-Ti-Ni particles

    NASA Astrophysics Data System (ADS)

    Scudino, S.; Ali, F.; Surreddi, K. B.; Prashanth, K. G.; Sakaliyska, M.; Eckert, J.

    2010-07-01

    Al-based metal matrix composites containing different volume fractions of nanocrystalline Al70Ti20Ni10 reinforcing particles have been produced by powder metallurgy and the effect of the volume fraction of reinforcement on the mechanical properties of the composites has been studied. Room temperature compression tests reveal a considerable improvement of the mechanical properties as compared to pure Aluminum. The compressive strength increases from 155 MPa for pure Al to about 200 and 240 MPa for the samples with 20 and 40 vol.% of reinforcement, respectively, while retaining appreciable plastic deformation with a fracture strain ranging between 43 and 28 %.

  2. Adherent Al2O3 scales formed on undoped NiCrAl alloys

    NASA Technical Reports Server (NTRS)

    Smialek, James L.

    1987-01-01

    Changes in the spalling behavior of Al2O3 scales formed on an undoped NiCrAl alloy are described. Two samples of Ni-15Cr-13Al (wt pct), one a control and the other sanded, were subjected to 25 oxidation cycles. It is observed that adherent scales formed on the sanded sample; however, the control sample had speckled, spalled scales. The data reveal that the adherent scales are caused by repeated removal of surface layers after each oxidation cycle. It is determined that interfacial segregation of sulfur influences spallation and sulfur removal increases bonding. The effect of moisture on scale adhesions is investigated.

  3. Atomic layer epitaxy of AlAs and AlGaAs

    NASA Astrophysics Data System (ADS)

    Meguro, T.; Iwai, S.; Aoyagi, Y.; Ozaki, K.; Yamamoto, Y.; Suzuki, T.; Okano, Y.; Hirata, A.

    1990-01-01

    Atomic layer epitaxy (ALE) of AlAs and AlGaAs with metalorganic vapor-phase epitaxy (MOVPE) under Ar-ion laser irradiation has been successfully realized in a triethylaluminum (TEA)/AsH 3 system for the first time. Comparison with the growth characteristics of MOVPE with alternative feeding modes of TMA/AsH 3 and TEA/AsH 3 is discussed. Application to laser-ALE of AlGaAs using a triethylgallium (TEG)/TEA/AsH 3 system is also discussed.

  4. Low cycle fatigue of FeAl(42 at. % Al) at room temperature

    SciTech Connect

    Hanes, D.B.; Gibala, R.

    1997-12-31

    The monotonic mechanical behavior in tension and compression of FeAl has been well documented. However, very little work has been done on the cyclic deformation behavior of this material. In this work, the behavior of FeAl (42 at. % Al) under low cycle fatigue was studied, including the effects of test environments and surface coatings. It was found that the fatigue life of this alloy is limited by environmental embrittlement. This embrittlement process can be equally well prevented by deformation in an oxygen environment or by coating the alloy with a protective film. The type of film applied appears to have little effect. Similar results were seen in monotonic testing.

  5. On the crack growth resistance and strength of the B2 iron aluminides Fe-40Al, Fe-45Al, and Fe-10Ni-40Al (at. %)

    SciTech Connect

    Schneibel, J.H.; Maziasz, P.J.

    1994-09-01

    The crack growth resistance and yield strength of the B2 iron aluminides Fe-40Al, Fe-45Al, are Fe-10Ni-40Al (at. %) have been investigated at room temperature laboratory air. After fast cooling from 1273 K, Fe-45Al and Fe-10Ni-40Al are much stronger than Fe-40Al, and exhibit considerably lower crack growth resistance. The crack growth resistance decreases with decreasing crack propagation velocity. Low crack propagation velocities favor intergranular fracture, whereas high velocities can lead to significant contributions from transgranular fracture. Boron additions to Fe-40Al and Fe-10Ni-40Al improve the crack growth resistance, reduce its dependence on the crack propagation velocity, and cause the path to be predominantly transgranular. In a plot of fracture toughness versus yield strength, the properties of the iron aluminides are similar to those of typical aluminum alloys.

  6. Density of Low-Temperature KF-AlF3 Aluminum Baths with Al2O3 and AlPO4 Additives

    NASA Astrophysics Data System (ADS)

    Vasková, Zuzana; Kontrík, Martin; Mlynáriková, Jarmila; Boča, Miroslav

    2015-02-01

    The density of the KF-AlF3 melts of various KF and AlF3 ratio with Al2O3 and AlPO4 addition has been measured using the Archimedean method. On the basis of the obtained density data the molar volumes of the melts were calculated. These molar volumes decrease with concentration of Al2O3 or AlPO4. In the system containing AlPO4, the relation between cryolite ratios (CRs) vs slopes of molar volume trend lines was identified with excellent correlation factor of R 2 = 0.9844, while in the system containing Al2O3 a discontinuity at CR = 2.5 can be observed.

  7. [Assay of three kinds of aluminum fractions (Al(a), Al(b) and Al(c)) in polynuclear aluminum solutions by Al-Ferron timed spectrophotometry and demarcation of their time limits].

    PubMed

    Wang, Chen-yi; Zhang, Cai-hua; Bi, Shu-ping; Zhang, Zhen-chao; Yang, Wei-hua

    2005-02-01

    Al-Ferron timed spectrophotometry assay is a basic method in the study on the formation of polynuclear hydroxyl aluminum species and their transformation laws in aqueous systems. In actual working process, this methodology has some dogmatism and arbitrariness in the time limits demarcation of the three kinds of aluminum fractions (Al(a), Al(b) and Al(c)) in polynuclear aluminum solutions, which makes this kind of classification rougher, and the experimental results non-reproducible. The reason for this difference is that the specific species within Al(a), Al(b) and Al(c) have different reaction mechanism and dynamics, and that specific species of Al(b) having different OH/Al ratios have different reaction rates with ferron. In this paper, the ExpAssoc distribution was applied to quantitatively fit the Al-Ferron reaction dynamics curve, and the extrapolation method was used to survey the 1 min measured value [Al(a)] of monomeric Al, which is hard to obtain in manual manipulation. The time demarcation between Al(b) and Al(c) should reach the point of the experimental data curve up to horizontal platform. The microwave-radiated technology was used to fast assay the total aluminum concentration [Al(T)]. With these methods, the contents of monomeric Al(a), polynuclear Al(b) and gel Al(c) can be conveniently and quantitatively measured. It offers a novel method for surmounting the arbitrariness in the measurement of the three kinds of aluminum fractions and the repetitive calculation of Al(a) and Al(b). PMID:15852869

  8. Characterization of Al30 in commercial poly-aluminum chlorohydrate by solid-state (27)Al NMR spectroscopy.

    PubMed

    Phillips, Brian L; Vaughn, John S; Smart, Scott; Pan, Long

    2016-08-15

    Investigation of commercially produced hydrolysis salts of aluminum by solid-state (27)Al NMR spectroscopy and size-exclusion chromatography (SEC) reveals well-defined and distinct Al environments that can be related to physicochemical properties. (27)Al MAS and MQ-MAS NMR spectroscopic data show that the local structure of the solids is dominated by moieties that closely resemble the Al30 polyoxocation (Al30O8(OH)56(H2O)26(18+)), accounting for 72-85% of the total Al. These Al30-like clusters elute as several size fractions by SEC. Comparison of the SEC and NMR results indicates that the Al30-like clusters includes intact isolated clusters, moieties of larger polymers or aggregates, and possibly fragments resembling δ-Al13 Keggin clusters. The coagulation efficacy of the solids appears to correlate best with the abundance of intact Al30-like clusters and of smaller species available to promote condensation reactions. PMID:27232539

  9. Nonstatistical fluctuations for deep inelastic processes in {sup 27}Al+{sup 27}Al collisions

    SciTech Connect

    Berceanu, I.; Duma, M.; Moisa, D.; Petrovici, M.; Pop, A.; Simion, V.; Zoppo, A. Del; D'Erasmo, G.; Imme, G.; Lanzano, G.; Pagano, A.; Pantaleo, A.; Raciti, G.

    2006-08-15

    The excitation functions (EFs) for different fragments produced in the {sup 27}Al+{sup 27}Al dissipative collisions have been measured in steps of 250 keV in the incident energy range 122-132 MeV. Deep inelastic processes have been selected by integrating events on a total kinetic energy loss window of 12 MeV between 20 and 32 MeV. Large fluctuations are observed in all the studied EFs. Large-channel cross-correlation coefficients confirm the nonstatistical origin of these fluctuations. The energy autocorrelation function (EAF) shows damped oscillation structure as expected when a dinuclear system with a lifetime [{tau}=(5.1{+-}2.1){center_dot}10{sup -21}s], similar with its revolution period (T=4.9{center_dot}10{sup -21}sec), is formed. From the periodicity of the EAF oscillations, information on the deformation of the {sup 27}Al+{sup 27}Al dinucleus is inferred.

  10. Formation of AlN in laser ablated plasma of Al in nitrogen ambient

    NASA Astrophysics Data System (ADS)

    Thareja, Raj K.; Sharma, A. K.

    2005-05-01

    We report on spectroscopic investigations of interaction of an expanding laser ablated plume of aluminum and graphite with nitrogen gas and the formation of AlN and CN. AlN and CN bands are formed by reactive process of ablated aluminum and graphite in ambient nitrogen pressures of 70 and 0.1 Torr and laser fluence of 500 and 12 Jcm-2 respectively. Images of the expanding plasma plume were captured using ICCD to understand the role of vapor and shock temperature in the formation of AlN. Instability observed in laser ablated plume at later times attributed to Rayleigh-Taylor instability could be the cause for weak AlN band observed in the emission spectrum.