Science.gov

Sample records for bhvo-2 bcr-2 reference

  1. Synthesis and Characterization of Five New F-bearing Basalt Reference Materials (Fba Glasses): Quantifying the Fluorine Content of the Basaltic Glass Standards BCR-2G, BHVO-2G. GSA-1G, GSC-1G, GSD-1G, GSE-1G, ML3B-G, KL2-G, and ALV-519-4

    NASA Astrophysics Data System (ADS)

    Guggino, S. N.; Hervig, R. L.

    2011-12-01

    -, detection of low-energy negative secondary ions (-5 kV), and a mass resolution that resolved 18OH. Homogeneity of the Fba glasses was established by both SIMS and EPMA. Glasses labeled Fba-2, -3. -4, and -5 pass statistical tests for homogeneity and may be used as EPMA or SIMS standards. SIMS calibration curves were constructed using the Fba glasses and other F standards of varying silica, iron, and sodium content, including Bt-3, F-phlog, NIST 610, KE-12, and UTR-2. The calibration curves revealed large matrix effects for the analysis of F by SIMS (~ 50%) between an Fba:Bt-3 curve and a high-silica glass:F-phlog curve. The Fba:Bt-3 calibration curve was used to determine the F contents (ppm ± 1 σ) of the following nine commonly used basaltic glass standards: BCR-2G (321 ± 15), BHVO-2G (297 ± 14), GSA-1G (7 ± 0.1), GSC-1G (9 ± 0.5), GSD-1G (18 ± 1), GSE-1G (154 ± 7), ML3B-G (47 ± 2), KL2-G (82 ± 4), ALV-519-4 (76 ± 4).

  2. Assessing the Accuracy and Precision of Inorganic Geochemical Data Produced through Flux Fusion and Acid Digestions: Multiple (60+) Comprehensive Analyses of BHVO-2 and the Development of Improved "Accepted" Values

    NASA Astrophysics Data System (ADS)

    Ireland, T. J.; Scudder, R.; Dunlea, A. G.; Anderson, C. H.; Murray, R. W.

    2014-12-01

    The use of geological standard reference materials (SRMs) to assess both the accuracy and the reproducibility of geochemical data is a vital consideration in determining the major and trace element abundances of geologic, oceanographic, and environmental samples. Calibration curves commonly are generated that are predicated on accurate analyses of these SRMs. As a means to verify the robustness of these calibration curves, a SRM can also be run as an unknown item (i.e., not included as a data point in the calibration). The experimentally derived composition of the SRM can thus be compared to the certified (or otherwise accepted) value. This comparison gives a direct measure of the accuracy of the method used. Similarly, if the same SRM is analyzed as an unknown over multiple analytical sessions, the external reproducibility of the method can be evaluated. Two common bulk digestion methods used in geochemical analysis are flux fusion and acid digestion. The flux fusion technique is excellent at ensuring complete digestion of a variety of sample types, is quick, and does not involve much use of hazardous acids. However, this technique is hampered by a high amount of total dissolved solids and may be accompanied by an increased analytical blank for certain trace elements. On the other hand, acid digestion (using a cocktail of concentrated nitric, hydrochloric and hydrofluoric acids) provides an exceptionally clean digestion with very low analytical blanks. However, this technique results in a loss of Si from the system and may compromise results for a few other elements (e.g., Ge). Our lab uses flux fusion for the determination of major elements and a few key trace elements by ICP-ES, while acid digestion is used for Ti and trace element analyses by ICP-MS. Here we present major and trace element data for BHVO-2, a frequently used SRM derived from a Hawaiian basalt, gathered over a period of over two years (30+ analyses by each technique). We show that both digestion

  3. Development of Microanaytical Reference Materials for In-situ Anaysis at the U.S. Geological Survey

    NASA Astrophysics Data System (ADS)

    Wilson, S.

    2006-05-01

    With the increased use of microanalysis in geochemical investigations comes the need for a reliable and diversified supply of reference materials homogenous at the micrometer scale to assist analysts in element quantification. To meet these requirements, the U.S. Geological Survey (USGS) has undertaken a program to develop a series of reference materials which cover a range of sample types currently being investigated in our microanalytical laboratories. Initial efforts have focused on the development of natural basalt glasses (BCR- 2G, BHVO-2G, BIR-1G, TB-1G, NKT-1G) from a variety of geologic settings. In addition to these natural basalt materials a series of synthetic basalt glasses GSA-1G, GSC-1G, GSD-1G, GSE-1G have also been developed with 65 trace elements at 0, 3, 30, and 300, ppm respectively. The homogeneity of these materials and their use in international microanalytical proficiency studies will be presented. Application of this technology to the development of glass reference materials as part of a USGS/NASA collaborative studies on the development of Lunar Soil Simulant material will also be discussed.

  4. [Determination of Sb and Bi in 24 international geological reference materials by using pressurized acid digestion-ICP-MS].

    PubMed

    Hu, Zhao-chu; Gao, Shan; Liu, Xiao-ming; Yuan, Hong-lin; Liu, Ye; Diwu, Chun-rong

    2007-12-01

    The authors studied in detail the memory effect of Bi, Sb, As and Te in ICP-MS. The produced memory effects of these element were in the order of Bi>Sb>Te>As. Bi was seriously adsorbed by the polypropylene sample storing bottle and the sample introduction system in the low nitric acid medium (0.01%-1% HNO3). The washout effect of 0.1% HF was found to be better than those of 6% HNO3 and 0.1% HClO4. Under the given experiment conditions, the instrumental limit of detection was 0.001 and 0.0001 ng x mL(-1) for Sb and Bi, respectively. The authors report the determination of Sb and Bi in 24 international geological reference materials by using pressurized acid digestion-ICP-MS (including AGV-2, BHVO-2, BCR-2, etc.). Most of the results were found to be in reasonable agreement with the reported values in the literature. The authors' determined values of Sb for GSR-1 (granite; 0.30 microg x g(-1)) and JP-1 (peridotite; 0.045 microg x g(-1)) are obviously higher than those reported values. This is attributed to the efficient pressurized acid digestion, which is generally much more efficient than conventional wet digestions for insoluble minerals. PMID:18330312

  5. Density of BCR-2 basalt glass at high pressure by X-ray Absorption Microtomography

    NASA Astrophysics Data System (ADS)

    Clark, A. N.; Lesher, C. E.; Gaudio, S. J.; Yamada, A.; Wang, Y.

    2009-12-01

    Improved understanding of compressibility and thermal expansion and their integral properties, density and volume, of basaltic liquids are important for modeling the thermodynamics of partial melting and crystallization, and melt migration in the Earth’s crust and mantle. We are using X-ray absorption in conjunction with microtomography to determine density of basalt glass/melt at high pressures from the linear attenuation coefficient of voxels calibrated using internal calibration standards at monochromatic energy. Experiments are conducted with the rotating anvil apparatus on the 13-BM-D beamline at the Advanced Photon Source, Argonne National Laboratory in an opposing anvil (Drickamer) assembly with 4 mm truncations and 20o taper. The sample and standards are contained within a single crystal diamond sleeve capped with Mo lids inserted into a graphite box-type heater with Mo leads and surrounded by pyrophillite, zirconia and a composite boron epoxy-diamond epoxy--pyrophillite gasket. Pressure is determined by using energy dispersive X-ray diffraction of MgO and Au contained within the capsule. Temperature is controlled to within ±25 oC by regulating power to the heater based on prior calibration. The density of USGS standard BCR-2 (Columbia River Basalt) glass is determined by this technique up to 3 GPa at room temperature giving a compressibility (Ko) for the glass of 70 ±5 GPa, assuming K’= 4. The cell was successfully heated to 900 oC at 1 GPa with tomographic data sets collected at 200 oC temperature intervals. The variation in density with temperature gives a thermal expansion for BCR-2 glass of 3x10-5 K-1. Success in performing microtomography under simultaneous high pressure-temperature conditions will enable this technique to be extended to the melting interval for basalt at elevated pressures in the near future.

  6. Advances in Quantitative Analyses and Reference Materials Related to Laser Ablation ICP-MS: A Look at Methods and New Directions

    NASA Astrophysics Data System (ADS)

    Koenig, A. E.; Ridley, W. I.

    2009-12-01

    The role of laser ablation ICP-MS (LA-ICP-MS) continues to expand both in geological sciences and other fields. As the technique continues to gain popularity, so too does the need for good reference materials and methods development and validation. Matrix matched reference materials (RMs) are required for calibration and quality control of LA-ICP-MS analyses. New advances in technology such as <200nm lasers and femtosecond lasers have reduced the dependence on matrix matching to some degree, but general matrix matching is still preferred. Much work has revolved around the available RMs such as the NIST 61x silicate glasses and several series of basaltic composition glasses such as the USGS natural basaltic glasses BCR-2g and synthetic basaltic glasses, the GS series (e.g. GSD-1g). While many quantitative hurdles have been recognized by analogous techniques such as EPMA and SIMS, some of these hurdles have not been fully addressed or validated for some cases of LA-ICP-MS. Trace element mapping by LA-ICP-MS is rapidly becoming more widespread for samples. Here relative differences in raw signal can be easily and rapidly obtained. However as too often is the case the magnitude of the relative differences in raw intensity are a function of different ablation yields, sample density or other factors. Methods of quantification for trace element mapping will be presented. The USGS has been developing microanalytical RMs intended for LA-ICP-MS for several years. The widely popular basaltic rock powders BCR-2, BIR-1 and BHVO-2 have all been successfully converted to homogeneous glasses suitable for LA-ICP-MS and have been in use by many workers. The newer synthetic basaltic glass GS series consists of 4 glasses of basaltic composition artificially doped at nominal concentrations of almost of trace elements at 400, 40, 4 and < 1 ppm. Additional developments in non-silcate or basaltic materials include the previously released MASS-1 Cu, Fe, Zn sulfide calibration RM (Wilson et

  7. Comprehensive Pb-Sr-Nd-Hf isotopic, trace element, and mineralogical characterization of mafic to ultramafic rock reference materials

    NASA Astrophysics Data System (ADS)

    Fourny, Anaïs.; Weis, Dominique; Scoates, James S.

    2016-03-01

    Controlling the accuracy and precision of geochemical analyses requires the use of characterized reference materials with matrices similar to those of the unknown samples being analyzed. We report a comprehensive Pb-Sr-Nd-Hf isotopic and trace element concentration data set, combined with quantitative phase analysis by XRD Rietveld refinement, for a wide range of mafic to ultramafic rock reference materials analyzed at the Pacific Centre for Isotopic and Geochemical Research, University of British Columbia. The samples include a pyroxenite (NIM-P), five basalts (BHVO-2, BIR-1a, JB-3, BE-N, GSR-3), a diabase (W-2), a dolerite (DNC-1), a norite (NIM-N), and an anorthosite (AN-G); results from a leucogabbro (Stillwater) are also reported. Individual isotopic ratios determined by MC-ICP-MS and TIMS, and multielement analyses by HR-ICP-MS are reported with 4-12 complete analytical duplicates for each sample. The basaltic reference materials have coherent Sr and Nd isotopic ratios with external precision below 50 ppm (2SD) and below 100 ppm for Hf isotopes (except BIR-1a). For Pb isotopic reproducibility, several of the basalts (JB-3, BHVO-2) require acid leaching prior to dissolution. The plutonic reference materials also have coherent Sr and Nd isotopic ratios (<50 ppm), however, obtaining good reproducibility for Pb and Hf isotopic ratios is more challenging for NIM-P, NIM-N, and AN-G due to a variety of factors, including postcrystallization Pb mobility and the presence of accessory zircon. Collectively, these results form a comprehensive new database that can be used by the geochemical community for evaluating the radiogenic isotope and trace element compositions of volcanic and plutonic mafic-ultramafic rocks.

  8. Determination of Fluorine in Fourteen Microanalytical Geologic Reference Materials using SIMS, EPMA, and Proton Induced Gamma Ray Emission (PIGE) Analysis

    NASA Astrophysics Data System (ADS)

    Guggino, S. N.; Hervig, R. L.

    2010-12-01

    Fluorine (F) is a volatile constituent of magmas and hydrous minerals, and trace amounts of F are incorporated into nominally anhydrous minerals such as olivine and clinopyroxene. Microanalytical techniques are routinely used to measure trace amounts of F at both high sensitivity and high spatial resolution in glasses and crystals. However, there are few well-established F concentrations for the glass standards routinely used in microanalytical laboratories, particularly standards of low silica, basaltic composition. In this study, we determined the F content of fourteen commonly used microanalytical glass standards of basaltic, intermediate, and rhyolitic composition. To serve as calibration standards, five basaltic glasses with ~0.2 to 2.5 wt% F were synthesized and characterized. A natural tholeiite from the East Pacific Rise was mixed with variable amounts of CaF2. The mixture was heated in a 1 atmosphere furnace to 1440 °C at fO2 = NNO for 30 minutes and quenched in water. Portions of the run products were studied by electron probe microanalysis (EPMA) and secondary ion mass spectrometry (SIMS). The EPMA used a 15 µm diameter defocused electron beam with a 15 kV accelerating voltage and a 25 nA primary current, a TAP crystal for detecting FKα X-rays, and Biotite 3 as the F standard. The F contents by EPMA agreed with the F added to the basalts after correction for mass loss during melting. The SIMS analyses used a primary beam of 16O- and detection of low-energy negative ions (-5 kV) at a mass resolution that resolved 18OH. Both microanalytical techniques confirmed homogeneity, and the SIMS calibration defined by EPMA shows an excellent linear trend with backgrounds of 2 ppm or less. Analyses of basaltic glass standards based on our synthesized calibration standards gave the following F contents and 2σ errors (ppm): ALV-519 = 83 ± 3; BCR-2G = 359 ± 6; BHVO-2G = 322 ± 15; GSA-1G = 10 ± 1; GSC-1G = 11 ± 1; GSD-1G = 19 ± 2; GSE-1G = 173 ± 1; KL2G (MPI

  9. A new basaltic glass microanalytical reference material for multiple techniques

    USGS Publications Warehouse

    Wilson, Steve; Koenig, Alan; Lowers, Heather

    2012-01-01

    The U.S. Geological Survey (USGS) has been producing reference materials since the 1950s. Over 50 materials have been developed to cover bulk rock, sediment, and soils for the geological community. These materials are used globally in geochemistry, environmental, and analytical laboratories that perform bulk chemistry and/or microanalysis for instrument calibration and quality assurance testing. To answer the growing demand for higher spatial resolution and sensitivity, there is a need to create a new generation of microanalytical reference materials suitable for a variety of techniques, such as scanning electron microscopy/X-ray spectrometry (SEM/EDS), electron probe microanalysis (EPMA), laser ablation inductively coupled mass spectrometry (LA-ICP-MS), and secondary ion mass spectrometry (SIMS). As such, the microanalytical reference material (MRM) needs to be stable under the beam, be homogeneous at scales of better than 10–25 micrometers for the major to ultra-trace element level, and contain all of the analytes (elements or isotopes) of interest. Previous development of basaltic glasses intended for LA-ICP-MS has resulted in a synthetic basaltic matrix series of glasses (USGS GS-series) and a natural basalt series of glasses (BCR-1G, BHVO-2G, and NKT-1G). These materials have been useful for the LA-ICP-MS community but were not originally intended for use by the electron or ion beam community. A material developed from start to finish with intended use in multiple microanalytical instruments would be useful for inter-laboratory and inter-instrument platform comparisons. This article summarizes the experiments undertaken to produce a basalt glass reference material suitable for distribution as a multiple-technique round robin material. The goal of the analytical work presented here is to demonstrate that the elemental homogeneity of the new glass is acceptable for its use as a reference material. Because the round robin exercise is still underway, only

  10. Reference Assessment

    ERIC Educational Resources Information Center

    Bivens-Tatum, Wayne

    2006-01-01

    This article presents interesting articles that explore several different areas of reference assessment, including practical case studies and theoretical articles that address a range of issues such as librarian behavior, patron satisfaction, virtual reference, or evaluation design. They include: (1) "Evaluating the Quality of a Chat Service"…

  11. Reference Services.

    ERIC Educational Resources Information Center

    Bunge, Charles A.

    1999-01-01

    Discusses library reference services. Topics include the historical development of reference services; instruction in library use, particularly in college and university libraries; guidance; information and referral services and how they differ from traditional question-answering service; and future concerns, including user fees and the planning…

  12. Reference frames and reference networks

    NASA Astrophysics Data System (ADS)

    Bosy, Jaroslaw; Krynski, Jan

    2015-12-01

    The summary of research activities concerning reference frames and reference networks performed in Poland in a period of 2011-2014 is presented. It contains the results of research on implementation of IUGG2011 and IAU2012 resolutions on reference systems, implementation of the ETRS89 in Poland, operational work of permanent IGS/ EUREF stations in Poland, operational work of ILRS laser ranging station in Poland, active GNSS station networks in Poland, maintenance of vertical control in Poland, maintenance and modernization of gravity control, and maintenance of magnetic control in Poland. The bibliography of the related works is given in references.

  13. Ready Reference.

    ERIC Educational Resources Information Center

    Koltay, Emery

    1999-01-01

    Includes the following ready reference information: "Publishers' Toll-Free Telephone Numbers"; "How to Obtain an ISBN (International Standard Book Number)"; "How to Obtain an ISSN (International Standard Serial Number)"; and "How to Obtain an SAN (Standard Address Number)". (AEF)

  14. Ready Reference.

    ERIC Educational Resources Information Center

    Koltay, Emery

    2001-01-01

    Includes four articles that relate to ready reference, including a list of publishers' toll-free telephone numbers and Web sites; how to obtain an ISBN (International Standard Book Number) and an ISSN (International Standard Serial Number); and how to obtain an SAN (Standard Address Number), for organizations that are involved in the book…

  15. Poroelastic references

    SciTech Connect

    Morency, Christina

    2014-12-12

    This file contains a list of relevant references on the Biot theory (forward and inverse approaches), the double-porosity and dual-permeability theory, and seismic wave propagation in fracture porous media, in RIS format, to approach seismic monitoring in a complex fractured porous medium such as Brady?s Geothermal Field.

  16. Homogeneity of the geochemical reference material BRP-1 (paraná basin basalt) and assessment of minimum mass

    USGS Publications Warehouse

    Cotta, Aloisio J. B.; Enzweiler, Jacinta; Wilson, Stephen A.; Perez, Carlos A.; Nardy, Antonio J. R.; Larizzatti, Joao H.

    2007-01-01

    Reference materials (RM) are required for quantitative analyses and their successful use is associated with the degree of homogeneity, and the traceability and confidence limits of the values established by characterisation. During the production of a RM, the chemical characterisation can only commence after it has been demonstrated that the material has the required level of homogeneity. Here we describe the preparation of BRP-1, a proposed geochemical reference material, and the results of the tests to evaluate its degree of homogeneity between and within bottles. BRP-1 is the first of two geochemical RM being produced by Brazilian institutions in collaboration with the United States Geological Survey (USGS) and the International Association of Geoanalysts (IAG). Two test portions of twenty bottles of BRP-1 were analysed by wavelength dispersive-XRF spectrometry and major, minor and eighteen trace elements were determined. The results show that for most of the investigated elements, the units of BRP-1 were homogeneous at conditions approximately three times more rigorous than those strived for by the test of “sufficient homogeneity”. Furthermore, the within bottle homogeneity of BRP-1 was evaluated using small beam (1 mm2) synchrotron radiation XRF spectrometry and, for comparison, the USGS reference materials BCR-2 and GSP-2 were also evaluated. From our data, it has been possible to assign representative minimum masses for some major constituents (1 mg) and for some trace elements (1-13 mg), except Zr in GSP-2, for which test portions of 74 mg are recommended.

  17. Library Reference Services.

    ERIC Educational Resources Information Center

    Miller, Constance; And Others

    1985-01-01

    Seven articles on library reference services highlight reference obsolescence in academic libraries, major studies of unobtrusive reference tests, methods for evaluating reference desk performance, reference interview evaluation, problems of reference desk control, online searching by end users, and reference collection development in…

  18. Reference Frames and Relativity.

    ERIC Educational Resources Information Center

    Swartz, Clifford

    1989-01-01

    Stresses the importance of a reference frame in mechanics. Shows the Galilean transformation in terms of relativity theory. Discusses accelerated reference frames and noninertial reference frames. Provides examples of reference frames with diagrams. (YP)

  19. Determination of the 87Sr/86Sr isotope ratio in USGS silicate reference materials by multi-collector ICP-mass spectrometry

    NASA Astrophysics Data System (ADS)

    Balcaen, Lieve; Schrijver, Isabel De; Moens, Luc; Vanhaecke, Frank

    2005-04-01

    Multi-collector ICP-mass spectrometry (MC-ICP-MS) was used for 87Sr/86Sr isotope ratio determination in newly introduced silicate reference materials from the US Geological Survey (USGS): granite G-3, andesite AGV-2, and basalt BCR-2. Next to the SrCO3 isotopic standard NIST SRM 987, also analogous USGS reference materials from the previous generation, and for which reference 87Sr/86Sr data obtained by TIMS are available, were analysed for validation purposes. Sample preparation consisted of acid digestion and subsequent isolation of Sr by means of a dedicated and commercially available crown ether-based resin. The Sr fractions thus obtained were analysed via MC-ICP-MS whereby mass discrimination was corrected for internally, while the isobaric interference at a mass-to-charge ratio of 86 caused by Kr impurities in the Ar gas was mathematically corrected for by using the signal for a Kr isotope free from spectral overlap. Finally, also the effect of the small amount of Rb that may still be present in the Sr fraction was corrected for mathematically on the basis of the signal intensity for 85Rb. The MC-ICP-MS results for G-2, AGV-1 and BCR-1 showed an excellent agreement with the corresponding TIMS values (<0.003% bias in all cases), such that it can be assumed that also the 87Sr/86Sr isotope ratio results obtained for the new reference materials are reliable.

  20. Computers and Reference Service.

    ERIC Educational Resources Information Center

    Purcell, Royal

    1989-01-01

    Discusses the current status and potential for automated library reference services in the areas of community information systems, online catalogs, remote online reference services, and telephone reference services. Several models of the reference procedure which might be used in developing expert systems are examined. (19 references) (CLB)

  1. Reference Service Policy Statement.

    ERIC Educational Resources Information Center

    Young, William F.

    This reference service policy manual provides general guidelines to encourage reference service of the highest possible quality and to insure uniform practice. The policy refers only to reference service in the University Libraries and is intended for use in conjunction with other policies and procedures issued by the Reference Services Division.…

  2. Reach for Reference. Four Recent Reference Books

    ERIC Educational Resources Information Center

    Safford, Barbara Ripp

    2004-01-01

    This article provides descriptions of four new science and technology encyclopedias that are appropriate for inclusion in upper elementary and/or middle school reference collections. "The Macmillan Encyclopedia of Weather" (Stern, Macmillan Reference/Gale), a one-volume encyclopedia for upper elementary and middle level students, is a…

  3. Fundamentals of Reference

    ERIC Educational Resources Information Center

    Mulac, Carolyn M.

    2012-01-01

    The all-in-one "Reference reference" you've been waiting for, this invaluable book offers a concise introduction to reference sources and services for a variety of readers, from library staff members who are asked to work in the reference department to managers and others who wish to familiarize themselves with this important area of…

  4. Live, Digital Reference.

    ERIC Educational Resources Information Center

    Kenney, Brian

    2002-01-01

    Discusses digital reference services, also known as virtual reference, chat reference, or online reference, based on a round table discussion at the 2002 American Library Association annual conference in Atlanta. Topics include numbers and marketing; sustainability; competition and models; evaluation methods; outsourcing; staffing and training;…

  5. Statistical Reference Datasets

    National Institute of Standards and Technology Data Gateway

    Statistical Reference Datasets (Web, free access)   The Statistical Reference Datasets is also supported by the Standard Reference Data Program. The purpose of this project is to improve the accuracy of statistical software by providing reference datasets with certified computational results that enable the objective evaluation of statistical software.

  6. Genetics Home Reference

    MedlinePlus

    Skip Navigation Bar Home Current Issue Past Issues Genetics Home Reference Past Issues / Spring 2007 Table of ... of this page please turn Javascript on. The Genetics Home Reference (GHR) Web site — ghr.nlm.nih. ...

  7. The Test of Reference.

    ERIC Educational Resources Information Center

    Childers, Thomas

    1980-01-01

    Reports the results of an unobtrusive study, from a user's viewpoint, of reference services available in the Suffolk Cooperative Library System. The study raises questions of policy centering around user expectations of library reference services. (RAA)

  8. Best Reference Sources 2001.

    ERIC Educational Resources Information Center

    Coutts, Brian; McConnell, Tamara

    2002-01-01

    Presents an annotated list of the best reference materials published in 2001. Discusses activity in the reference publishing industry; costs; and lists print materials, Web sites, databases, and CD-ROMs. (LRW)

  9. Assessment of Reference Services.

    ERIC Educational Resources Information Center

    Von Seggern, Marilyn

    1987-01-01

    This annotated bibliography of materials dealing with the evaluation of library reference services is arranged by category including literature success, quality, and accuracy of answers; cost and task analysis; interviews and communication; classification of reference questions; reference collections; staff availability; use and nonuse of…

  10. Academic Library Reference Services.

    ERIC Educational Resources Information Center

    Batt, Fred

    This examination of the philosophy and objectives of academic library reference services provides an overview of the major reference approaches to fulfilling the following primary objectives of reference services: (1) providing accurate answers to patrons' questions and/or helping patrons find sources to pursue their research needs; (2) building…

  11. Use of Ga for mass bias correction for the accurate determination of copper isotope ratio in the NIST SRM 3114 Cu standard and geological samples by MC-ICP MS

    NASA Astrophysics Data System (ADS)

    Zhang, T.; Zhou, L.; Tong, S.

    2015-12-01

    The absolute determination of the Cu isotope ratio in NIST SRM 3114 based on a regression mass bias correction model is performed for the first time with NIST SRM 944 Ga as the calibrant. A value of 0.4471±0.0013 (2SD, n=37) for the 65Cu/63Cu ratio was obtained with a value of +0.18±0.04 ‰ (2SD, n=5) for δ65Cu relative to NIST 976.The availability of the NIST SRM 3114 material, now with the absolute value of the 65Cu/63Cu ratio and a δ65Cu value relative to NIST 976 makes it suitable as a new candidate reference material for Cu isotope studies. In addition, a protocol is described for the accurate and precise determination of δ65Cu values of geological reference materials. Purification of Cu from the sample matrix was performed using the AG MP-1M Bio-Rad resin. The column recovery for geological samples was found to be 100±2% (2SD, n=15).A modified method of standard-sample bracketing with internal normalization for mass bias correction was employed by adding natural Ga to both the sample and the solution of NIST SRM 3114, which was used as the bracketing standard. An absolute value of 0.4471±0.0013 (2SD, n=37) for 65Cu/63Cu quantified in this study was used to calibrate the 69Ga/71Ga ratio in the two adjacent bracketing standards of SRM 3114,their average value of 69Ga/71Ga was then used to correct the 65Cu/63Cu ratio in the sample. Measured δ65Cu values of 0.18±0.04‰ (2SD, n=20),0.13±0.04‰ (2SD, n=9),0.08±0.03‰ (2SD, n=6),0.01±0.06‰(2SD, n=4) and 0.26±0.04‰ (2SD, n=7) were obtained for five geological reference materials of BCR-2,BHVO-2,AGV-2,BIR-1a,and GSP-2,respectively,in agreement with values obtained in previous studies.

  12. High frequency reference electrode

    DOEpatents

    Kronberg, J.W.

    1994-05-31

    A high frequency reference electrode for electrochemical experiments comprises a mercury-calomel or silver-silver chloride reference electrode with a layer of platinum around it and a layer of a chemically and electrically resistant material such as TEFLON around the platinum covering all but a small ring or halo' at the tip of the reference electrode, adjacent to the active portion of the reference electrode. The voltage output of the platinum layer, which serves as a redox electrode, and that of the reference electrode are coupled by a capacitor or a set of capacitors and the coupled output transmitted to a standard laboratory potentiostat. The platinum may be applied by thermal decomposition to the surface of the reference electrode. The electrode provides superior high-frequency response over conventional electrodes. 4 figs.

  13. High frequency reference electrode

    DOEpatents

    Kronberg, James W.

    1994-01-01

    A high frequency reference electrode for electrochemical experiments comprises a mercury-calomel or silver-silver chloride reference electrode with a layer of platinum around it and a layer of a chemically and electrically resistant material such as TEFLON around the platinum covering all but a small ring or "halo" at the tip of the reference electrode, adjacent to the active portion of the reference electrode. The voltage output of the platinum layer, which serves as a redox electrode, and that of the reference electrode are coupled by a capacitor or a set of capacitors and the coupled output transmitted to a standard laboratory potentiostat. The platinum may be applied by thermal decomposition to the surface of the reference electrode. The electrode provides superior high-frequency response over conventional electrodes.

  14. Optical voltage reference

    DOEpatents

    Rankin, Richard; Kotter, Dale

    1994-01-01

    An optical voltage reference for providing an alternative to a battery source. The optical reference apparatus provides a temperature stable, high precision, isolated voltage reference through the use of optical isolation techniques to eliminate current and impedance coupling errors. Pulse rate frequency modulation is employed to eliminate errors in the optical transmission link while phase-lock feedback is employed to stabilize the frequency to voltage transfer function.

  15. Optical voltage reference

    DOEpatents

    Rankin, R.; Kotter, D.

    1994-04-26

    An optical voltage reference for providing an alternative to a battery source is described. The optical reference apparatus provides a temperature stable, high precision, isolated voltage reference through the use of optical isolation techniques to eliminate current and impedance coupling errors. Pulse rate frequency modulation is employed to eliminate errors in the optical transmission link while phase-lock feedback is employed to stabilize the frequency to voltage transfer function. 2 figures.

  16. Ethics and Reference Services.

    ERIC Educational Resources Information Center

    Danielson, Elena S.

    1997-01-01

    While revised ethical codes provide helpful guidelines, reference archivists face many ethical questions raised by rapidly evolving technology, changing expectations, and inconsistent privacy laws that have no clear answers. Discusses issues related to reference searching, codification of ethics, cultural property and the responsibility of…

  17. Creating a Reference Toolbox.

    ERIC Educational Resources Information Center

    Scott, Jane

    1997-01-01

    To help students understand that references are tools used to locate specific information, one librarian has her third-grade students create their own reference toolboxes as she introduces dictionaries, atlases, encyclopedias, and thesauri. Presents a lesson plan to introduce print and nonprint thesauri to third and fourth graders and includes a…

  18. Reference Service Training Manual.

    ERIC Educational Resources Information Center

    Mielke, John; Young, William

    This manual is primarily designed as an orientation program for librarians new to the Reference Services Division at the State University of New York at Albany University Libraries. It contains practical information and some of the procedures necessary for providing service at the reference desk in these libraries. The appendices provide samples…

  19. Marketing Reference Services.

    ERIC Educational Resources Information Center

    Norman, O. Gene

    1995-01-01

    Relates the marketing concept to library reference services. Highlights include a review of the literature and an overview of marketing, including research, the marketing mix, strategic plan, marketing plan, and marketing audit. Marketing principles are applied to reference services through the marketing mix elements of product, price, place, and…

  20. Library Reference Service.

    ERIC Educational Resources Information Center

    Schippleck, Suzanne

    The Inglewood, California, public library provides a manual on reference service. The theory, purpose, and objectives of reference are noted, and goals and activities are described in terms of budget, personnel, resources, and services. A chapter on organization covers service structure, information services, relationships with other library…

  1. Rethinking Virtual Reference

    ERIC Educational Resources Information Center

    Tenopir, Carol

    2004-01-01

    Virtual reference services seem a natural extension of libraries digital collections and the emphasis on access to the library anytime, anywhere. If patrons use the library from home, it makes sense to provide them with person-to-person online reference. The Library of Congress (LC), OCLC, and several large library systems have developed and…

  2. Automated Periodical Reference Service.

    ERIC Educational Resources Information Center

    Ellefsen, David

    1985-01-01

    Describes public library reference service which allows patrons to type out search instructions on a computer terminal, review and select references, and receive, by high-speed printer, facsimile copy of selected periodical articles. Development of periodicals center at main county library and use of self-coaching SEARCH HELPER system are…

  3. An Online Reference System.

    ERIC Educational Resources Information Center

    Chisman, Janet; Treat, William

    1984-01-01

    Describes a computer aid developed to assist in academic library reference service using the DataPhase Circulation System, an automated system that features full cataloging records in database and permits local programing. Access points (subject, type of reference work, course) and database structure and user screens are highlighted. (EJS)

  4. Leading Education Reference Sources.

    ERIC Educational Resources Information Center

    Spencer, Michael D.

    This annotated bibliography focuses on, but is not limited to, reference sources on education found in the library at St. Bonaventure University, New York. The ERIC database leads the list of leading education reference sources. Also mentioned are the "Thesaurus of ERIC Descriptors" and the Academic Index (InfoTrak) computer system. Other…

  5. Uranium reference materials

    SciTech Connect

    Donivan, S.; Chessmore, R.

    1987-07-01

    The Technical Measurements Center has prepared uranium mill tailings reference materials for use by remedial action contractors and cognizant federal and state agencies. Four materials were prepared with varying concentrations of radionuclides, using three tailings materials and a river-bottom soil diluent. All materials were ground, dried, and blended thoroughly to ensure homogeneity. The analyses on which the recommended values for nuclides in the reference materials are based were performed, using independent methods, by the UNC Geotech (UNC) Chemistry Laboratory, Grand Junction, Colorado, and by C.W. Sill (Sill), Idaho National Engineering Laboratory, Idaho Falls, Idaho. Several statistical tests were performed on the analytical data to characterize the reference materials. Results of these tests reveal that the four reference materials are homogeneous and that no large systematic bias exists between the analytical methods used by Sill and those used by TMC. The average values for radionuclides of the two data sets, representing an unbiased estimate, were used as the recommended values for concentrations of nuclides in the reference materials. The recommended concentrations of radionuclides in the four reference materials are provided. Use of these reference materials will aid in providing uniform standardization among measurements made by remedial action contractors. 11 refs., 9 tabs.

  6. EPA QUICK REFERENCE GUIDES

    EPA Science Inventory

    EPA Quick Reference Guides are compilations of information on chemical and biological terrorist agents. The information is presented in consistent format and includes agent characteristics, release scenarios, health and safety data, real-time field detection, effect levels, samp...

  7. Value of Information References

    SciTech Connect

    Morency, Christina

    2014-12-12

    This file contains a list of relevant references on value of information (VOI) in RIS format. VOI provides a quantitative analysis to evaluate the outcome of the combined technologies (seismology, hydrology, geodesy) used to monitor Brady's Geothermal Field.

  8. Enterprise Reference Library

    NASA Technical Reports Server (NTRS)

    Bickham, Grandin; Saile, Lynn; Havelka, Jacque; Fitts, Mary

    2011-01-01

    Introduction: Johnson Space Center (JSC) offers two extensive libraries that contain journals, research literature and electronic resources. Searching capabilities are available to those individuals residing onsite or through a librarian s search. Many individuals have rich collections of references, but no mechanisms to share reference libraries across researchers, projects, or directorates exist. Likewise, information regarding which references are provided to which individuals is not available, resulting in duplicate requests, redundant labor costs and associated copying fees. In addition, this tends to limit collaboration between colleagues and promotes the establishment of individual, unshared silos of information The Integrated Medical Model (IMM) team has utilized a centralized reference management tool during the development, test, and operational phases of this project. The Enterprise Reference Library project expands the capabilities developed for IMM to address the above issues and enhance collaboration across JSC. Method: After significant market analysis for a multi-user reference management tool, no available commercial tool was found to meet this need, so a software program was built around a commercial tool, Reference Manager 12 by The Thomson Corporation. A use case approach guided the requirements development phase. The premise of the design is that individuals use their own reference management software and export to SharePoint when their library is incorporated into the Enterprise Reference Library. This results in a searchable user-specific library application. An accompanying share folder will warehouse the electronic full-text articles, which allows the global user community to access full -text articles. Discussion: An enterprise reference library solution can provide a multidisciplinary collection of full text articles. This approach improves efficiency in obtaining and storing reference material while greatly reducing labor, purchasing and

  9. Precision displacement reference system

    DOEpatents

    Bieg, Lothar F.; Dubois, Robert R.; Strother, Jerry D.

    2000-02-22

    A precision displacement reference system is described, which enables real time accountability over the applied displacement feedback system to precision machine tools, positioning mechanisms, motion devices, and related operations. As independent measurements of tool location is taken by a displacement feedback system, a rotating reference disk compares feedback counts with performed motion. These measurements are compared to characterize and analyze real time mechanical and control performance during operation.

  10. Membrane reference electrode

    DOEpatents

    Redey, L.; Bloom, I.D.

    1988-01-21

    A reference electrode utilizes a small thin, flat membrane of a highly conductive glass placed on a small diameter insulator tube having a reference material inside in contact with an internal voltage lead. When the sensor is placed in a non-aqueous ionic electrolytic solution, the concentration difference across the glass membrane generates a low voltage signal in precise relationship to the concentration of the species to be measured, with high spatial resolution. 2 figs.

  11. Reference Man anatomical model

    SciTech Connect

    Cristy, M.

    1994-10-01

    The 70-kg Standard Man or Reference Man has been used in physiological models since at least the 1920s to represent adult males. It came into use in radiation protection in the late 1940s and was developed extensively during the 1950s and used by the International Commission on Radiological Protection (ICRP) in its Publication 2 in 1959. The current Reference Man for Purposes of Radiation Protection is a monumental book published in 1975 by the ICRP as ICRP Publication 23. It has a wealth of information useful for radiation dosimetry, including anatomical and physiological data, gross and elemental composition of the body and organs and tissues of the body. The anatomical data includes specified reference values for an adult male and an adult female. Other reference values are primarily for the adult male. The anatomical data include much data on fetuses and children, although reference values are not established. There is an ICRP task group currently working on revising selected parts of the Reference Man document.

  12. Cooperative Reference: Hazards, Rewards, Prospects.

    ERIC Educational Resources Information Center

    Morgan, Candace D.; And Others

    1979-01-01

    Discusses the problems, benefits, and future of cooperative library reference services in five separate papers: (1) keynote address; (2) interlibrary reference communication; (3) quality control; (4) computerized cooperative reference; and (5) national reference service. (JD)

  13. Setting reference targets

    SciTech Connect

    Ruland, R.E.

    1997-04-01

    Reference Targets are used to represent virtual quantities like the magnetic axis of a magnet or the definition of a coordinate system. To explain the function of reference targets in the sequence of the alignment process, this paper will first briefly discuss the geometry of the trajectory design space and of the surveying space, then continue with an overview of a typical alignment process. This is followed by a discussion on magnet fiducialization. While the magnetic measurement methods to determine the magnetic centerline are only listed (they will be discussed in detail in a subsequent talk), emphasis is given to the optical/mechanical methods and to the task of transferring the centerline position to reference targets.

  14. Reference selenocentric net

    NASA Astrophysics Data System (ADS)

    Nefedyev, Yura

    2012-08-01

    The catalogues based on mission “Apollo” and reference nets of the west lunar hemisphere made by missions “Zond 5”, ”Zond 8” cover small part of the Moon surface (zone from - 20 to +40 degrees by latitude). Three ALSEP stations were used to transform “Apollo” topographic coordinates. Transformation mean - square errors are less than 80 meters and measurement’s errors are about 60 meters. On this account positions inaccuracy near and between ALSEP stations are less 150 meters. The offset from place of the location ALSEP enlarges the supposed mistake is more than 300 m and this is a major part of the lunar surface. Catalogues of the mission “Apollo” realize quasidynamic coordinate system. Distribution reference nets DMA/A 15, NOS/USGS and DMA/603 mission “Apollo” on visible side of the Moon didn’t bring in appreciable results. Only KSC - 1162 realizes dynamic coordinate system and covers zone from - 70 to +70 degrees by latitude. The reference selenodetic net KSC - 1162 was made in the dynamic coordinate system. Analysis KSC - 1162 catalogue shows it corresponds to an essential requirements. It has enough reference points to cove r main areas of the lunar visible side. Reference points accuracy for plan coordinates is ± 40 meters and it is ± 80 in height. The purposes of investigation are increasing concentration accuracy and expansion of selenodetic control system based on optimal coordinate transformations. At present the best method of the expansion selenodetic reference net wide lunar area is the use of coordinate’s transformation matrix. Constituents of matrix and displacement vectors can be obtained by transform available general points in KSC - 1162 and transformable in its system catalogues. As a result was obtained summary reference net by expansion KSC - 1162 selenodetic system using 12 cosmic and ground selenodesic catalogues. In the future we plan to bind to the KSC - 1162 catalogue reference coordinate system data

  15. NASCAP programmer's reference manual

    NASA Technical Reports Server (NTRS)

    Mandell, M. J.; Stannard, P. R.; Katz, I.

    1993-01-01

    The NASA Charging Analyzer Program (NASCAP) is a computer program designed to model the electrostatic charging of complicated three-dimensional objects, both in a test tank and at geosynchronous altitudes. This document is a programmer's reference manual and user's guide. It is designed as a reference to experienced users of the code, as well as an introduction to its use for beginners. All of the many capabilities of NASCAP are covered in detail, together with examples of their use. These include the definition of objects, plasma environments, potential calculations, particle emission and detection simulations, and charging analysis.

  16. Aluminum reference electrode

    DOEpatents

    Sadoway, Donald R.

    1988-01-01

    A stable reference electrode for use in monitoring and controlling the process of electrolytic reduction of a metal. In the case of Hall cell reduction of aluminum, the reference electrode comprises a pool of molten aluminum and a solution of molten cryolite, Na.sub.3 AlF.sub.6, wherein the electrical connection to the molten aluminum does not contact the highly corrosive molten salt solution. This is accomplished by altering the density of either the aluminum (decreasing the density) or the electrolyte (increasing the density) so that the aluminum floats on top of the molten salt solution.

  17. Multifunctional reference electrode

    DOEpatents

    Redey, L.; Vissers, D.R.

    1981-12-30

    A multifunctional, low mass reference electrode of a nickel tube, thermocouple means inside the nickel tube electrically insulated therefrom for measuring the temperature thereof, a housing surrounding the nickel tube, an electrolyte having a fixed sulfide ion activity between the housing and the outer surface of the nickel tube forming the nickel/nickel sulfide/sulfide half-cell are described. An ion diffusion barrier is associated with the housing in contact with the electrolyte. Also disclosed is a cell using the reference electrode to measure characteristics of a working electrode.

  18. Aluminum reference electrode

    DOEpatents

    Sadoway, D.R.

    1988-08-16

    A stable reference electrode is described for use in monitoring and controlling the process of electrolytic reduction of a metal. In the case of Hall cell reduction of aluminum, the reference electrode comprises a pool of molten aluminum and a solution of molten cryolite, Na[sub 3]AlF[sub 6], wherein the electrical connection to the molten aluminum does not contact the highly corrosive molten salt solution. This is accomplished by altering the density of either the aluminum (decreasing the density) or the electrolyte (increasing the density) so that the aluminum floats on top of the molten salt solution. 1 fig.

  19. Multifunctional reference electrode

    DOEpatents

    Redey, Laszlo; Vissers, Donald R.

    1983-01-01

    A multifunctional, low mass reference electrode of a nickel tube, thermocouple means inside the nickel tube electrically insulated therefrom for measuring the temperature thereof, a housing surrounding the nickel tube, an electrolyte having a fixed sulfide ion activity between the housing and the outer surface of the nickel tube forming the nickel/nickel sulfide/sulfide half-cell. An ion diffusion barrier is associated with the housing in contact with the electrolyte. Also disclosed is a cell using the reference electrode to measure characteristics of a working electrode.

  20. Assessment and Accountability in Reference Work. Part V: Reference Evaluation.

    ERIC Educational Resources Information Center

    Hults, Patricia; And Others

    1992-01-01

    Includes four articles that discuss the evaluation of library reference services. Topics addressed include unobtrusive testing; measuring the accountability of reference librarians by behavioral rather than factual evaluation; on-the-job training of reference librarians; and faculty expectations of academic reference librarians. (52 references)…

  1. Evaluating the Reference Product.

    ERIC Educational Resources Information Center

    Strong, Gary E.

    1980-01-01

    Examines quantitative and qualitative evaluation and analysis of Washington State Library reference activities, based on research activities of the Consortium for Public Library Innovation. Several methods of data collection for a sample day are discussed, including a user ticket and a patterns of information requests form. (Author)

  2. International reference ionosphere 1990

    NASA Technical Reports Server (NTRS)

    Bilitza, Dieter; Rawer, K.; Bossy, L.; Kutiev, I.; Oyama, K.-I.; Leitinger, R.; Kazimirovsky, E.

    1990-01-01

    The International Reference Ionosphere 1990 (IRI-90) is described. IRI described monthly averages of the electron density, electron temperature, ion temperature, and ion composition in the altitude range from 50 to 1000 km for magnetically quiet conditions in the non-auroral ionosphere. The most important improvements and new developments are summarized.

  3. Reference Services in Archives.

    ERIC Educational Resources Information Center

    Whalen, Lucille; And Others

    1986-01-01

    This 16-article issue focuses on history, policy, services, users, organization, evaluation, and automation of the archival reference process. Collections at academic research libraries, a technical university, Board of Education, business archives, a bank, labor and urban archives, a manuscript repository, religious archives, and regional history…

  4. Genetics Home Reference: cherubism

    MedlinePlus

    ... About Genetics Home Reference Site Map Contact Us Selection Criteria for Links Copyright Privacy Accessibility FOIA Viewers & Players U.S. Department of Health & Human Services National Institutes of Health National Library of Medicine Lister Hill National Center for Biomedical Communications 8600 ...

  5. Chat Reference. SPEC Kit.

    ERIC Educational Resources Information Center

    Ronan, Jana, Comp.; Turner, Carol, Comp.

    2002-01-01

    This SPEC (Systems and Procedures Exchange Center) Kit presents the results of a survey of Association of Research Libraries (ARL) member libraries designed to gather data on chat reference service. A total of 66 of 124 ARL member libraries responded to the survey. A copy of the questionnaire with tabulated results is presented. Representative…

  6. Reference Sources for Nursing

    ERIC Educational Resources Information Center

    Nursing Outlook, 1976

    1976-01-01

    The ninth revision (including a Canadian supplement) of a list of nursing reference works lists items in the following sections: abstract journals, audiovisuals, bibliographies, dictionaries, directories, drug lists and pharmacologies, educational programs, histories, indexes, legal guides, library administration and organization, research grants,…

  7. THAI, REFERENCE GRAMMAR.

    ERIC Educational Resources Information Center

    NOSS, RICHARD B.

    A REFERENCE GRAMMAR FOR THE THAI LANGUAGE IS PROVIDED. THE MAIN STRUCTURAL FEATURES OF STANDARD SPOKEN THAI ARE OUTLINED AND ELABORATED BY SUBCLASSIFICATION AND EXAMPLE. IN ADDITION, AN INDEX OF MINOR FORM-CLASS MEMBERS IS PROVIDED. THE APPROACH TO CLASSIFICATION OF GRAMMATICAL FEATURES FOLLOWS CURRENT TECHNIQUES OF AMERICAN DESCRIPTIVE…

  8. Best Reference 2006

    ERIC Educational Resources Information Center

    Coutts, Brian E.; LaGuardia, Cheryl

    2007-01-01

    Reading reference sources, whether on paper or on the screen, often leads to enlightened thinking, especially for library patrons. In an earlier age, enlightened monarchs surrounded themselves with leading intellectuals and patronized the arts. Today, people have the advantage of the world's collected wisdom at their fingertips in the form of…

  9. The Unreliability of References

    ERIC Educational Resources Information Center

    Barden, Dennis M.

    2008-01-01

    When search consultants, like the author, are invited to propose their services in support of a college or university seeking new leadership, they are generally asked a fairly standard set of questions. But there is one question that they find among the most difficult to answer: How do they check a candidate's references to ensure that they know…

  10. Virtual Reference Services.

    ERIC Educational Resources Information Center

    Brewer, Sally

    2003-01-01

    As the need to access information increases, school librarians must create virtual libraries. Linked to reliable reference resources, the virtual library extends the physical collection and library hours and lets students learn to use Web-based resources in a protected learning environment. The growing number of virtual schools increases the need…

  11. Internet Issues in Reference.

    ERIC Educational Resources Information Center

    Tenopir, Carol

    1995-01-01

    Discusses the impact of Internet access on library reference services based on 1994 interviews with almost two dozen university librarians. Highlights include library policy, overcrowded workstations and methods of controlling use, recreational use of terminals that interferes with more formal library use, restriction as a form of censorship, and…

  12. Reference Model Development

    SciTech Connect

    Jepsen, Richard

    2011-11-02

    Presentation from the 2011 Water Peer Review in which principal investigator discusses project progress to develop a representative set of Reference Models (RM) for the MHK industry to develop baseline cost of energy (COE) and evaluate key cost component/system reduction pathways.

  13. Reference Collections and Standards.

    ERIC Educational Resources Information Center

    Winkel, Lois

    1999-01-01

    Reviews six reference materials for young people: "The New York Public Library Kid's Guide to Research"; "National Audubon Society First Field Guide. Mammals"; "Star Wars: The Visual Dictionary"; "Encarta Africana"; "World Fact Book, 1998"; and "Factastic Book of 1001 Lists". Includes ordering information.(AEF)

  14. Dietary Reference Intakes

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The Dietary Reference Intakes (DRI) are recommendations intended to provide a framework for nutrient intake evaluation, as well as meal planning on the basis of nutrient adequacy. They are nutrient, not food based recommendations, created with chronic disease risk reduction as the primary goal, as ...

  15. The Reference Encounter Model.

    ERIC Educational Resources Information Center

    White, Marilyn Domas

    1983-01-01

    Develops model of the reference interview which explicitly incorporates human information processing, particularly schema ideas presented by Marvin Minsky and other theorists in cognitive processing and artificial intelligence. Questions are raised concerning use of content analysis of transcribed verbal protocols as methodology for studying…

  16. A GUJARATI REFERENCE GRAMMAR.

    ERIC Educational Resources Information Center

    CARDONA, GEORGE

    THIS REFERENCE GRAMMAR WAS WRITTEN TO FILL THE NEED FOR AN UP-TO-DATE ANALYSIS OF THE MODERN LANGUAGE SUITABLE FOR LANGUAGE LEARNERS AS WELL AS LINGUISTS. THE AUTHOR LISTS IN THE INTRODUCTION THOSE STUDIES PREVIOUS TO THIS ONE WHICH MAY BE OF INTEREST TO THE READER. INCLUDED IN HIS ANALYSIS OF THE LANGUAGE ARE MAJOR CHAPTERS ON--(1) PHONOLOGY, (2)…

  17. Generating Multimodal References

    ERIC Educational Resources Information Center

    van der Sluis, Ielka; Krahmer, Emiel

    2007-01-01

    This article presents a new computational model for the generation of multimodal referring expressions (REs), based on observations in human communication. The algorithm is an extension of the graph-based algorithm proposed by Krahmer, van Erk, and Verleg (2003) and makes use of a so-called Flashlight Model for pointing. The Flashlight Model…

  18. Reference Book Guides.

    ERIC Educational Resources Information Center

    Webb, Bill, Ed.

    For each reference work there is a 5 1/2 x 8 1/2" card with information about the work in brief, standardized format. The card indicates what the subject coverage is, the types of materials included, the service given, frequency of publication, procedure for use, an example of the procedure, a sample entry with explanatory notes, other places to…

  19. Reference-Dependent Sympathy

    ERIC Educational Resources Information Center

    Small, Deborah A.

    2010-01-01

    Natural disasters and other traumatic events often draw a greater charitable response than do ongoing misfortunes, even those that may cause even more widespread misery, such as famine or malaria. Why is the response disproportionate to need? The notion of reference dependence critical to Prospect Theory (Kahneman & Tversky, 1979) maintains that…

  20. Selecting a Reference Object

    ERIC Educational Resources Information Center

    Miller, Jared E.; Carlson, Laura A.; Hill, Patrick L.

    2011-01-01

    One way to describe the location of an object is to relate it to another object. Often there are many nearby objects, each of which could serve as a candidate to be the reference object. A common theoretical assumption is that features that make a given object salient relative to the candidate set are instrumental in determining which is selected.…

  1. Shuttle Reference Data

    NASA Astrophysics Data System (ADS)

    2002-12-01

    This collection of shuttle reference data contains the following information: shuttle abort history, shuttle abort modes, abort decisions, space shuttle rendezvous maneuvers, space shuttle main engines, space shuttle solid rocket boosters, hold-down posts, SRB (solid rocket boosters) ignition, electrical power distribution, hydraulic power units, thrust vector control, SBR rate gyro assemblies, SBR separation and Space Shuttle Super Super Light Weight Tank (SLWT).

  2. Hospitality Services Reference Book.

    ERIC Educational Resources Information Center

    Texas Tech Univ., Lubbock. Home Economics Curriculum Center.

    This reference book provides information needed by employees in hospitality services occupations. It includes 29 chapters that cover the following topics: the hospitality services industry; professional ethics; organization and management structures; safety practices and emergency procedures; technology; property maintenance and repair; purchasing…

  3. Reference Ranges & What They Mean

    MedlinePlus

    ... be limited. Home Visit Global Sites Search Help? Reference Ranges and What They Mean Share this page: Was this page helpful? Overview | Reference range defined | Where are the reference ranges? | Limits ...

  4. OSH technical reference manual

    SciTech Connect

    Not Available

    1993-11-01

    In an evaluation of the Department of Energy (DOE) Occupational Safety and Health programs for government-owned contractor-operated (GOCO) activities, the Department of Labor`s Occupational Safety and Health Administration (OSHA) recommended a technical information exchange program. The intent was to share written safety and health programs, plans, training manuals, and materials within the entire DOE community. The OSH Technical Reference (OTR) helps support the secretary`s response to the OSHA finding by providing a one-stop resource and referral for technical information that relates to safe operations and practice. It also serves as a technical information exchange tool to reference DOE-wide materials pertinent to specific safety topics and, with some modification, as a training aid. The OTR bridges the gap between general safety documents and very specific requirements documents. It is tailored to the DOE community and incorporates DOE field experience.

  5. The NPL reference hazemeter

    NASA Astrophysics Data System (ADS)

    Freeman, G. H. C.

    1992-09-01

    The reference hazemeter is a development of a commercial pivotable sphere hazemeter. The principle improvements are a high quality photometer and its associated electronic and temperature controller, a stable power supply for the source and the determination of the lamp current of illuminants A and C, improvements to the optics to achieve a well shaped beam, and mechanical modifications to accommodate the improvements and allow a good mechanical movement. Various tests were carried out to validate the instrument behavior. These identified systematic errors caused by inter-reflections. To reduce the inter-reflection errors, the blue filter and the input lenses were antireflection coated. The reference hazemeter complies with BS 2782--methods of testing plastics; part 5--optical and color properties; method 521A--determination of haze of film and sheet. A calibration service using the hazemeter is now in operation.

  6. Alignment reference device

    DOEpatents

    Patton, Gail Y.; Torgerson, Darrel D.

    1987-01-01

    An alignment reference device provides a collimated laser beam that minimizes angular deviations therein. A laser beam source outputs the beam into a single mode optical fiber. The output end of the optical fiber acts as a source of radiant energy and is positioned at the focal point of a lens system where the focal point is positioned within the lens. The output beam reflects off a mirror back to the lens that produces a collimated beam.

  7. Reference structure tomography

    NASA Astrophysics Data System (ADS)

    Brady, David J.; Pitsianis, Nikos P.; Sun, Xiaobai

    2004-07-01

    Reference structure tomography (RST) uses multidimensional modulations to encode mappings between radiating objects and measurements. RST may be used to image source-density distributions, estimate source parameters, or classify sources. The RST paradigm permits scan-free multidimensional imaging, data-efficient and computation-efficient source analysis, and direct abstraction of physical features. We introduce the basic concepts of RST and illustrate the use of RST for multidimensional imaging based on a geometric radiation model.

  8. Is anaphoric reference cooperative?

    PubMed

    Kantola, Leila; van Gompel, Roger P G

    2016-01-01

    Two experiments investigated whether the choice of anaphoric expression is affected by the presence of an addressee. Following a context sentence and visual scene, participants described a target scene that required anaphoric reference. They described the scene either to an addressee (Experiment 1) or without an addressee (Experiment 2). When an addressee was present in the task, participants used more pronouns and fewer repeated noun phrases when the referent was the grammatical subject in the context sentence than when it was the grammatical object and they used more pronouns when there was no competitor than when there was. They used fewer pronouns and more repeated noun phrases when a visual competitor was present in the scene than when there was no visual competitor. In the absence of an addressee, linguistic context effects were the same as those when an addressee was present, but the visual effect of the competitor disappeared. We conclude that visual salience effects are due to adjustments that speakers make when they produce reference for an addressee, whereas linguistic salience effects appear whether or not speakers have addressees. PMID:26165163

  9. Celestial Reference Frame

    NASA Astrophysics Data System (ADS)

    Jacobs, Christopher S.

    2013-09-01

    Concepts and Background: This paper gives an overview of modern celestial reference frames as realized at radio frequencies using the Very Long baseline Interferometry (VLBI) technique. We discuss basic celestial reference frame concepts, desired properties, and uses. We review the networks of antennas used for this work. We briefly discuss the history of the science of astrometry touching upon the discovery of precession, proper motion, nutation, and parallax, and the field of radio astronomy. Building Celestial Frames: Next, we discuss the multi-step process of building a celestial frame: First candidate sources are identified based on point-like properties from single dish radio telescopes surveys. Second, positions are refined using connected element interferometers such as the Very Large Array, and the ATCA. Third, positions of approximately milli-arcsecond (mas) accuracy are determined using intercontinental VLBI surveys. Fourth, sub-mas positions are determined by multiyear programs using intercontinental VLBI. These sub-mas sets of positions are then verified by multiple teams in preparation for release to non-specialists in the form of an official IAU International Celestial Reference Frame (ICRF). The process described above has until recently been largely restricted to work at S/X-band (2.3/8.4 GHz). However, in the last decade sub-mas work has expanded to include celestial frames at K-band (24 GHz), Ka-band (32 GHz), and Q-band (43 GHz). While these frames currently have the disadvantage of far smaller data sets, the astrophysical quality of the sources themselves improves at these higher frequencies and thus make these frequencies attractive for realizations of celestial reference frames. Accordingly, we review progress at these higher frequency bands. Path to the Future: We discuss prospects for celestial reference frames over the next decade. We present an example of an error budget for astrometric VLBI and discuss the budget's use as a tool for

  10. SEI reference mission

    NASA Technical Reports Server (NTRS)

    Weary, Dwayne

    1992-01-01

    Information is given in viewgraph form on the Space Exploration Initiative (SEI). The goal of the reference mission is to expand the human presence to the moon and Mars in order to enhance our understanding of the universe, to seek terrestrial benefits from this exploration, and to establish the beginnings of a sustainable spacefaring civilization. Topics covered here include a phased definition of initial programmatic milestones and follow-on capabilities, near-term mission strategy, a lunar mission timeline, and a Mars mission timeline.

  11. Bushland, Texas Reference ET Calculator

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The Bushland Reference Evapotranspiration (ET) Calculator was developed at the USDA-ARS Conservation and Production Research Laboratory, Bushland, Texas, for calculating grass and alfalfa reference ET. It uses the ASCE Standardized Reference ET Equation for calculating reference ET at hourly and dai...

  12. Expanding the Repertoire of Reference.

    ERIC Educational Resources Information Center

    Frantz, Paul

    1991-01-01

    Suggests several ways that reference librarians can improve their skills beyond library school training. Reference interviews are discussed; effective methods of browsing the reference collection are described; opportunities for learning at the reference desk are suggested; and professional reading and study is discussed, including professional…

  13. Coal data: A reference

    SciTech Connect

    Not Available

    1995-02-01

    This report, Coal Data: A Reference, summarizes basic information on the mining and use of coal, an important source of energy in the US. This report is written for a general audience. The goal is to cover basic material and strike a reasonable compromise between overly generalized statements and detailed analyses. The section ``Supplemental Figures and Tables`` contains statistics, graphs, maps, and other illustrations that show trends, patterns, geographic locations, and similar coal-related information. The section ``Coal Terminology and Related Information`` provides additional information about terms mentioned in the text and introduces some new terms. The last edition of Coal Data: A Reference was published in 1991. The present edition contains updated data as well as expanded reviews and additional information. Added to the text are discussions of coal quality, coal prices, unions, and strikes. The appendix has been expanded to provide statistics on a variety of additional topics, such as: trends in coal production and royalties from Federal and Indian coal leases, hours worked and earnings for coal mine employment, railroad coal shipments and revenues, waterborne coal traffic, coal export loading terminals, utility coal combustion byproducts, and trace elements in coal. The information in this report has been gleaned mainly from the sources in the bibliography. The reader interested in going beyond the scope of this report should consult these sources. The statistics are largely from reports published by the Energy Information Administration.

  14. Antares reference telescope system

    NASA Astrophysics Data System (ADS)

    Viswanathan, V. K.; Kaprelian, E.; Swann, T.; Parker, J.; Wolfe, P.; Woodfin, G.; Knight, D.

    Antares is a 24 beam, 40 TW carbon dioxide laser fusion system currently nearing completion. The 24 beams will be focused onto a tiny target. It is to position the targets to within 10 (SIGMA)m of a selected nominal position, which may be anywhere within a fixed spherical region 1 cm in diameter. The Antares reference telescope system is intended to help achieve this goal for alignment and viewing of the various targets used in the laser system. The Antares reference telescope system consists of two similar electrooptical systems positioned in a near orthogonal manner in the target chamber area of the laser. Each of these consists of four subsystems: (1) a fixed 9% optical imaging subsystem which produces an image of the target at the vidicon; (2) a reticle projection subsystem which superimposes an image of the reticle pattern at the vidicon; (3) an adjustable front lighting subsystem which illuminates the target; and (4) an adjustable back lighting subsystem which also can be used to illuminate the target. The various optical, mechanical, and vidicon design considerations and tradeoffs are discussed. The final system chosen and its current status are described.

  15. Preliminary characterisation of new glass reference materials (GSA-1G, GSC-1G, GSD-1G and GSE-1G) by laser ablation-inductively coupled plasma-mass spectrometry using 193 nm, 213 nm and 266 nm wavelengths

    USGS Publications Warehouse

    Guillong, M.; Hametner, K.; Reusser, E.; Wilson, S.A.; Gunther, D.

    2005-01-01

    New glass reference materials GSA-1G, GSC-1G, GSD-1G and GSE-1G have been characterised using a prototype solid state laser ablation system capable of producing wavelengths of 193 nm, 213 nm and 266 nm. This system allowed comparison of the effects of different laser wavelengths under nearly identical ablation and ICP operating conditions. The wavelengths 213 nm and 266 nm were also used at higher energy densities to evaluate the influence of energy density on quantitative analysis. In addition, the glass reference materials were analysed using commercially available 266 nm Nd:YAG and 193 nm ArF excimer lasers. Laser ablation analysis was carried out using both single spot and scanning mode ablation. Using laser ablation ICP-MS, concentrations of fifty-eight elements were determined with external calibration to the NIST SRM 610 glass reference material. Instead of applying the more common internal standardisation procedure, the total concentration of all element oxide concentrations was normalised to 100%. Major element concentrations were compared with those determined by electron microprobe. In addition to NIST SRM 610 for external calibration, USGS BCR-2G was used as a more closely matrix-matched reference material in order to compare the effect of matrix-matched and non matrix-matched calibration on quantitative analysis. The results show that the various laser wavelengths and energy densities applied produced similar results, with the exception of scanning mode ablation at 266 nm without matrix-matched calibration where deviations up to 60% from the average were found. However, results acquired using a scanning mode with a matrix-matched calibration agreed with results obtained by spot analysis. The increased abundance of large particles produced when using a scanning ablation mode with NIST SRM 610, is responsible for elemental fractionation effects caused by incomplete vaporisation of large particles in the ICP.

  16. Tank characterization reference guide

    SciTech Connect

    De Lorenzo, D.S.; DiCenso, A.T.; Hiller, D.B.; Johnson, K.W.; Rutherford, J.H.; Smith, D.J.; Simpson, B.C.

    1994-09-01

    Characterization of the Hanford Site high-level waste storage tanks supports safety issue resolution; operations and maintenance requirements; and retrieval, pretreatment, vitrification, and disposal technology development. Technical, historical, and programmatic information about the waste tanks is often scattered among many sources, if it is documented at all. This Tank Characterization Reference Guide, therefore, serves as a common location for much of the generic tank information that is otherwise contained in many documents. The report is intended to be an introduction to the issues and history surrounding the generation, storage, and management of the liquid process wastes, and a presentation of the sampling, analysis, and modeling activities that support the current waste characterization. This report should provide a basis upon which those unfamiliar with the Hanford Site tank farms can start their research.

  17. PASCAL/48 reference manual

    NASA Technical Reports Server (NTRS)

    Knight, J. C.; Hamm, R. W.

    1984-01-01

    PASCAL/48 is a programming language for the Intel MCS-48 series of microcomputers. In particular, it can be used with the Intel 8748. It is designed to allow the programmer to control most of the instructions being generated and the allocation of storage. The language can be used instead of ASSEMBLY language in most applications while allowing the user the necessary degree of control over hardware resources. Although it is called PASCAL/48, the language differs in many ways from PASCAL. The program structure and statements of the two languages are similar, but the expression mechanism and data types are different. The PASCAL/48 cross-compiler is written in PASCAL and runs on the CDC CYBER NOS system. It generates object code in Intel hexadecimal format that can be used to program the MCS-48 series of microcomputers. This reference manual defines the language, describes the predeclared procedures, lists error messages, illustrates use, and includes language syntax diagrams.

  18. Long life reference electrode

    DOEpatents

    Yonco, R.M.; Nagy, Z.

    1987-07-30

    An external, reference electrode is provided for long term use with a high temperature, high pressure system. The electrode is arranged in a vertical, electrically insulative tube with an upper portion serving as an electrolyte reservoir and a lower portion in electrolytic communication with the system to be monitored. The lower end portion includes a flow restriction such as a porous plug to limit the electrolyte release into the system. A piston equalized to the system pressure is fitted into the upper portion of the tube to impart a small incremental pressure to the electrolyte. The piston is selected of suitable size and weight to cause only a slight flow of electrolyte through the porous plug into the high pressure system. This prevents contamination of the electrolyte but is of such small flow rate that operating intervals of a month or more can be achieved. 2 figs.

  19. Long life reference electrode

    DOEpatents

    Yonco, Robert M.; Nagy, Zoltan

    1989-01-01

    An external, reference electrode is provided for long term use with a high temperature, high pressure system. The electrode is arranged in a vertical, electrically insulative tube with an upper portion serving as an electrolyte reservior and a lower portion in electrolytic communication with the system to be monitored. The lower end portion includes a flow restriction such as a porous plug to limit the electrolyte release into the system. A piston equalized to the system pressure is fitted into the upper portion of the tube to impart a small incremental pressure to the electrolyte. The piston is selected of suitable size and weight to cause only a slight flow of electrolyte through the porous plug into the high pressure system. This prevents contamination of the electrolyte but is of such small flow rate that operating intervals of a month or more can be achieved.

  20. Long life reference electrode

    DOEpatents

    Yonco, R.M.; Nagy, Z.

    1989-04-04

    An external, reference electrode is provided for long term use with a high temperature, high pressure system. The electrode is arranged in a vertical, electrically insulative tube with an upper portion serving as an electrolyte reservoir and a lower portion in electrolytic communication with the system to be monitored. The lower end portion includes a flow restriction such as a porous plug to limit the electrolyte release into the system. A piston equalized to the system pressure is fitted into the upper portion of the tube to impart a small incremental pressure to the electrolyte. The piston is selected of suitable size and weight to cause only a slight flow of electrolyte through the porous plug into the high pressure system. This prevents contamination of the electrolyte but is of such small flow rate that operating intervals of a month or more can be achieved. 2 figs.

  1. Nuclear Science References Database

    SciTech Connect

    Pritychenko, B.; Běták, E.; Singh, B.; Totans, J.

    2014-06-15

    The Nuclear Science References (NSR) database together with its associated Web interface, is the world's only comprehensive source of easily accessible low- and intermediate-energy nuclear physics bibliographic information for more than 210,000 articles since the beginning of nuclear science. The weekly-updated NSR database provides essential support for nuclear data evaluation, compilation and research activities. The principles of the database and Web application development and maintenance are described. Examples of nuclear structure, reaction and decay applications are specifically included. The complete NSR database is freely available at the websites of the National Nuclear Data Center (http://www.nndc.bnl.gov/nsr) and the International Atomic Energy Agency (http://www-nds.iaea.org/nsr)

  2. Magnetohydrodynamic inertial reference system

    NASA Astrophysics Data System (ADS)

    Eckelkamp-Baker, Dan; Sebesta, Henry R.; Burkhard, Kevin

    2000-07-01

    Optical platforms increasingly require attitude knowledge and optical instrument pointing at sub-microradian accuracy. No low-cost commercial system exists to provide this level of accuracy for guidance, navigation, and control. The need for small, inexpensive inertial sensors, which may be employed in pointing control systems that are required to satisfy angular line-of-sight stabilization jitter error budgets to levels of 1-3 microradian rms and less, has existed for at least two decades. Innovations and evolutions in small, low-noise inertial angular motion sensor technology and advances in the applications of the global positioning system have converged to allow improvement in acquisition, tracking and pointing solutions for a wide variety of payloads. We are developing a small, inexpensive, and high-performance inertial attitude reference system that uses our innovative magnetohydrodynamic angular rate sensor technology.

  3. Praxis language reference manual

    SciTech Connect

    Walker, J.H.

    1981-01-01

    This document is a language reference manual for the programming language Praxis. The document contains the specifications that must be met by any compiler for the language. The Praxis language was designed for systems programming in real-time process applications. Goals for the language and its implementations are: (1) highly efficient code generated by the compiler; (2) program portability; (3) completeness, that is, all programming requirements can be met by the language without needing an assembler; and (4) separate compilation to aid in design and management of large systems. The language does not provide any facilities for input/output, stack and queue handling, string operations, parallel processing, or coroutine processing. These features can be implemented as routines in the language, using machine-dependent code to take advantage of facilities in the control environment on different machines.

  4. Reference Artifacts for NDE

    SciTech Connect

    Bono, M; Hibbard, R; Martz, H E

    2003-02-11

    Two reference artifacts will be fabricated for this study. One of the artifacts will have a cylindrical geometry and will contain features similar to those on an SNRT target. The second artifact will have a spherical geometry and will contain features similar to those on a Double Shell target. The artifacts were designed for manufacturability and to provide a range of features that can be measured using NDE methods. The cylindrical reference artifact is illustrated in Figure 1. This artifact consists of a polystyrene body containing two steps and a machined slot, into which will fit a tracer made of doped polystyrene. The polystyrene body contains several grooves and can be fabricated entirely on a diamond turning machine. The body can be machined by turning a PS rod to a diameter slightly greater than the finished diameter of 2 mm. The part can be moved off-axis to face it off and to machine the steps, slot, and grooves. The tracer contains a drilled hole and a milled slot, which could be machined with a single setup on a milling machine. Once assembled, the artifact could be placed in a Be tube or other structure relevant to target assemblies. The assembled artifact will contain many features that could be measured using various NDE methods. Some of these features are: Diameter; Maximum height; Step height; Dimensions of upper step; Radius at the union of the bottom of step and the vertical wall; Sizes of the grooves; Distance from step to groove; Slot width; Slot height; Location of the groove beneath the tracer; Diameter and location of drilled hole in tracer; and Size and location of slot in tracer. The spherical reference artifact is illustrated in Figure 2. This artifact is intended to replicate a double shell target, which consists of concentric polymer spheres separated by aerogel. The artifact consists of an upper hemispherical shell composed of 1% BrCH, which mates via a step joint with a hemispherical component made of polystyrene. This lower component

  5. Sensor Characteristics Reference Guide

    SciTech Connect

    Cree, Johnathan V.; Dansu, A.; Fuhr, P.; Lanzisera, Steven M.; McIntyre, T.; Muehleisen, Ralph T.; Starke, M.; Banerjee, Pranab; Kuruganti, T.; Castello, C.

    2013-04-01

    The Buildings Technologies Office (BTO), within the U.S. Department of Energy (DOE), Office of Energy Efficiency and Renewable Energy (EERE), is initiating a new program in Sensor and Controls. The vision of this program is: • Buildings operating automatically and continuously at peak energy efficiency over their lifetimes and interoperating effectively with the electric power grid. • Buildings that are self-configuring, self-commissioning, self-learning, self-diagnosing, self-healing, and self-transacting to enable continuous peak performance. • Lower overall building operating costs and higher asset valuation. The overarching goal is to capture 30% energy savings by enhanced management of energy consuming assets and systems through development of cost-effective sensors and controls. One step in achieving this vision is the publication of this Sensor Characteristics Reference Guide. The purpose of the guide is to inform building owners and operators of the current status, capabilities, and limitations of sensor technologies. It is hoped that this guide will aid in the design and procurement process and result in successful implementation of building sensor and control systems. DOE will also use this guide to identify research priorities, develop future specifications for potential market adoption, and provide market clarity through unbiased information

  6. ENRAF gauge reference level calculations

    SciTech Connect

    Huber, J.H., Fluor Daniel Hanford

    1997-02-06

    This document describes the method for calculating reference levels for Enraf Series 854 Level Detectors as installed in the tank farms. The reference level calculation for each installed level gauge is contained herein.

  7. Fundamentals of Managing Reference Collections

    ERIC Educational Resources Information Center

    Singer, Carol A.

    2012-01-01

    Whether a library's reference collection is large or small, it needs constant attention. Singer's book offers information and insight on best practices for reference collection management, no matter the size, and shows why managing without a plan is a recipe for clutter and confusion. In this very practical guide, reference librarians will learn:…

  8. Outstanding Reference Sources of 1986.

    ERIC Educational Resources Information Center

    Kuhlman, James R.

    1987-01-01

    This annotated bibliography lists 37 reference sources for small and medium sized public and academic libraries, categorized by subject area. These titles were selected by the Reference Sources Committee of the Reference and Adult Services Division of the American Library Association. (CLB)

  9. Gestural Viewpoint Signals Referent Accessibility

    ERIC Educational Resources Information Center

    Debreslioska, Sandra; Özyürek, Asli; Gullberg, Marianne; Perniss, Pamela

    2013-01-01

    The tracking of entities in discourse is known to be a bimodal phenomenon. Speakers achieve cohesion in speech by alternating between full lexical forms, pronouns, and zero anaphora as they track referents. They also track referents in co-speech gestures. In this study, we explored how viewpoint is deployed in reference tracking, focusing on…

  10. Knowledge Management and Reference Services

    ERIC Educational Resources Information Center

    Gandhi, Smiti

    2004-01-01

    Many corporations are embracing knowledge management (KM) to capture the intellectual capital of their employees. This article focuses on KM applications for reference work in libraries. It defines key concepts of KM, establishes a need for KM for reference services, and reviews various KM initiatives for reference services.

  11. Students' Perceptions of Reference Letters

    ERIC Educational Resources Information Center

    Payne, Brian K.; Appel, Jonathan; Smith, Donald H.; Hoofnagle, Kara

    2006-01-01

    This study examines students' perceptions of reference letters. Students (n = 444) were asked to describe how they perceived reference letters. Four themes were uncovered. First, some students perceived reference letters as useful for employers. Second, some students perceived the letters as important for students seeking employment or admission…

  12. Reference Management in Instructive Discourse

    ERIC Educational Resources Information Center

    Maes, Alfons; Arts, Anja; Noordman, Leo

    2004-01-01

    This article investigates the effect of 2 language-in-use factors on the introduction and maintenance of referents in instructive discourse. These factors, implemented as conditions in an instructive production task, were the assumed visual identity for the reader of the objects or referents to be referred to in the instructions (visually same vs.…

  13. Focusing on Quality Reference Service.

    ERIC Educational Resources Information Center

    Bicknell, Tracy

    1994-01-01

    Discussion of the assessment of the quality of library reference service focuses on four aspects of service interaction: user needs and expectations, staff behavior and communication skills, the reference environment, and staff morale and workload. Measurement techniques for each aspect are also described. (Contains 36 references.) (LRW)

  14. Cultural Literacy and Reference Service.

    ERIC Educational Resources Information Center

    D'Aniello, Charles A.

    1989-01-01

    Examines the role of library reference services in the enhancement of cultural literacy. The discussion covers the relationship between the extent of cultural literacy possessed by reference librarians and the quality of librarian patron interactions, and the role of reference sources in the cultural literacy of librarians and patrons. (53…

  15. New Reference: Diversifying Service Delivery.

    ERIC Educational Resources Information Center

    Garner, Imogen

    This paper describes the experiences of a recent change process that focused on the delivery of reference services at the University of Western Australia (UWA). UWA reference librarians felt that they could not fulfill all of their duties while working from the reference desk for a significant period of time each day; they wanted time away from…

  16. Reference Policies and Procedures Manual.

    ERIC Educational Resources Information Center

    George Mason Univ., Fairfax, VA.

    This guide to services of the reference department of Fenwick Library, George Mason University, is intended for use by staff in the department, as well as the general public. Areas covered include (1) reference desk services to users; (2) reference desk support procedures; (3) off desk services; (4) collection development, including staff…

  17. Capillary reference half-cell

    DOEpatents

    Hall, S.H.

    1996-02-13

    The present invention is a reference half-cell electrode wherein intermingling of test fluid with reference fluid does not affect the performance of the reference half-cell over a long time. This intermingling reference half-cell may be used as a single or double junction submersible or surface reference electrode. The intermingling reference half-cell relies on a capillary tube having a first end open to reference fluid and a second end open to test fluid wherein the small diameter of the capillary tube limits free motion of fluid within the capillary to diffusion. The electrode is placed near the first end of the capillary in contact with the reference fluid. The method of operation of the present invention begins with filling the capillary tube with a reference solution. After closing the first end of the capillary, the capillary tube may be fully submerged or partially submerged with the second open end inserted into test fluid. Since the electrode is placed near the first end of the capillary, and since the test fluid may intermingle with the reference fluid through the second open end only by diffusion, this intermingling capillary reference half-cell provides a stable voltage potential for long time periods. 11 figs.

  18. Capillary reference half-cell

    DOEpatents

    Hall, Stephen H.

    1996-01-01

    The present invention is a reference half-cell electrode wherein intermingling of test fluid with reference fluid does not affect the performance of the reference half-cell over a long time. This intermingling reference half-cell may be used as a single or double junction submersible or surface reference electrode. The intermingling reference half-cell relies on a capillary tube having a first end open to reference fluid and a second end open to test fluid wherein the small diameter of the capillary tube limits free motion of fluid within the capillary to diffusion. The electrode is placed near the first end of the capillary in contact with the reference fluid. The method of operation of the present invention begins with filling the capillary tube with a reference solution. After closing the first end of the capillary, the capillary tube may be fully submerged or partially submerged with the second open end inserted into test fluid. Since the electrode is placed near the first end of the capillary, and since the test fluid may intermingle with the reference fluid through the second open end only by diffusion, this intermingling capillary reference half-cell provides a stable voltage potential for long time periods.

  19. Reach for Reference: Elementary-Middle School Science Reference Collections

    ERIC Educational Resources Information Center

    Safford, Barbara Ripp

    2005-01-01

    This article presents a brief review of some new school science reference works. Two of the sources are traditional, while one is considered experimental. The two traditional reference works reviewed are "The American Heritage Children's Science Dictionary" for upper elementary grades, and "The American Heritage Student Science Dictionary" for…

  20. Statewide Supplemental Reference Service: New Jersey's Model for Backup Reference.

    ERIC Educational Resources Information Center

    Bromberg, Peter

    2001-01-01

    Discusses the history of backup reference service in the state of New Jersey including the transition from regional backup service; describes the current statewide service; and considers future service possibilities in light of recent trends, including a decrease in the number of reference questions being received in libraries. (LRW)

  1. User Preferences in Reference Services: Virtual Reference and Academic Libraries

    ERIC Educational Resources Information Center

    Cummings, Joel; Cummings, Lara; Frederiksen, Linda

    2007-01-01

    This study examines the use of chat in an academic library's user population and where virtual reference services might fit within the spectrum of public services offered by academic libraries. Using questionnaires, this research demonstrates that many within the academic community are open to the idea of chat-based reference or using chat for…

  2. Reference Readiness for AV Questions.

    ERIC Educational Resources Information Center

    Drolet, Leon L., Jr.

    1981-01-01

    Reviews 50 reference tools which librarians can use to answer almost any audiovisual question including queries on trivia, equipment selection, biographical information, and motion picture ratings. (LLS)

  3. Queuing Theory and Reference Transactions.

    ERIC Educational Resources Information Center

    Terbille, Charles

    1995-01-01

    Examines the implications of applying the queuing theory to three different reference situations: (1) random patron arrivals; (2) random durations of transactions; and (3) use of two librarians. Tables and figures represent results from spreadsheet calculations of queues for each reference situation. (JMV)

  4. Moving Reference to the Web.

    ERIC Educational Resources Information Center

    McGlamery, Susan; Coffman, Steve

    2000-01-01

    Explores the possibility of using Web contact center software to offer reference assistance to remote users. Discusses a project by the Metropolitan Cooperative Library System/Santiago Library System consortium to test contact center software and to develop a virtual reference network. (Author/LRW)

  5. Reference and the Technology Connection

    ERIC Educational Resources Information Center

    Riedling, Ann

    2005-01-01

    In this article, the influence of timesaving and inspiring reference technologies on the field of reference services is assessed. Library media specialists are advised to be aware of and embrace such emerging technologies, as these will enable them to make information gathering effective and efficient and create information-literate students.

  6. "In Your Face" Reference Service.

    ERIC Educational Resources Information Center

    Lipow, Anne Grodzins

    1999-01-01

    Discusses changes in library reference service that have occurred with growing Internet use. Topics include the human factor that is still needed; the nature of reference questions; the goal of user self-sufficiency; the invisible nature of much of librarians' work; and providing real-time, interactive point-of-need service to remote users. (LRW)

  7. Reference Services: A Handmaid's Tale.

    ERIC Educational Resources Information Center

    Beck, Clare

    1991-01-01

    Discussion of problems in library reference services focuses on the influence of gender roles. A historical overview of gender roles in the development of American librarianship is presented that highlights stereotyped views of and attitudes toward women, which the author suggests still have influences on librarianship today. (17 references) (LRW)

  8. The Virtual Reference Librarian's Handbook.

    ERIC Educational Resources Information Center

    Lipow, Anne Grodzins

    This book is a practical guide to librarians and their administrators who are thinking about or in the early stages of providing virtual reference service. Part 1, "The Decision to Go Virtual," provides a context for thinking about virtual reference, including the benefits and problems, getting in the virtual frame of mind, and shopping for…

  9. Robot at the Reference Desk?

    ERIC Educational Resources Information Center

    Smith, Karen F.

    1986-01-01

    Describes how a librarian, assisted by a knowledge engineer, developed a computerized reference assistance system for a separate government documents department. Rationale for the expert system, problems in selecting reference materials and user questions to computerize, and the formulation of a workable human/computer interface are covered. A…

  10. Expert Systems for Reference Work.

    ERIC Educational Resources Information Center

    Parrot, James R.

    1986-01-01

    Discussion of library reference work that may be suitable for use of expert systems focuses on (1) information and literature searches, and (2) requests to interpret bibliographic references and locate items listed. Systems and computer-assisted instruction modules designed for information retrieval at the University of Waterloo Library are…

  11. Reference Service in Law Libraries.

    ERIC Educational Resources Information Center

    Sasala, Kathleen M.

    Ten law librarians, at one private and three academic law libraries, were studied to ascertain what types of reference services they provide to their patrons. The current model employed in public libraries today was used as the baseline against which to measure these legal reference services. This model employs five traditional categories of:…

  12. Improved ultrasonic standard reference blocks

    NASA Technical Reports Server (NTRS)

    Eitzen, D. G.; Sushinsky, G. F.; Chwirut, D. J.; Bechtoldt, C. J.; Ruff, A. W.

    1976-01-01

    A program to improve the quality, reproducibility and reliability of nondestructive testing through the development of improved ASTM-type ultrasonic reference standards is described. Reference blocks of aluminum, steel, and titanium alloys are to be considered. Equipment representing the state-of-the-art in laboratory and field ultrasonic equipment was obtained and evaluated. RF and spectral data on ten sets of ultrasonic reference blocks have been taken as part of a task to quantify the variability in response from nominally identical blocks. Techniques for residual stress, preferred orientation, and micro-structural measurements were refined and are applied to a reference block rejected by the manufacturer during fabrication in order to evaluate the effect of metallurgical condition on block response. New fabrication techniques for reference blocks are discussed and ASTM activities are summarized.

  13. Generalizing indexical-functional reference

    SciTech Connect

    Schoppers, M.; Shu, R.

    1996-12-31

    The goals of situated agents generally do not specify particular objects: they require only that some suitable object should be chosen and manipulated (e.g. any red block). Situated agents engaged in deictic reference grounding, however, may well track a chosen referent object with such fixity of purpose that an unchosen object may be regarded as an obstacle even though it satisfies the agent`s goals. In earlier work this problem was bridged by hand-coding. This paper lifts the problem to the symbol level, endowing agents with perceptual referent selection actions and performing those actions as required to allow or disallow opportunistic re-selection of referents. Our work preserves the ability of situated agents to find and track specific objects, adds an ability to automatically exploit the opportunities allowed by nonspecific references, and provides a starting point for studying how much opportunistic perception is appropriate.

  14. Reference and Standard Atmosphere Models

    NASA Technical Reports Server (NTRS)

    Johnson, Dale L.; Roberts, Barry C.; Vaughan, William W.; Parker, Nelson C. (Technical Monitor)

    2002-01-01

    This paper describes the development of standard and reference atmosphere models along with the history of their origin and use since the mid 19th century. The first "Standard Atmospheres" were established by international agreement in the 1920's. Later some countries, notably the United States, also developed and published "Standard Atmospheres". The term "Reference Atmospheres" is used to identify atmosphere models for specific geographical locations. Range Reference Atmosphere Models developed first during the 1960's are examples of these descriptions of the atmosphere. This paper discusses the various models, scopes, applications and limitations relative to use in aerospace industry activities.

  15. PIRLA DBMS QUICK REFERENCE GUIDE

    EPA Science Inventory

    This handbook facilitates the use of the PIRLA (Paleoecological Investigation of Recent Lake Acidification) database retrievals by showing all possible inputs, outputs, ranges, and quick reference information that you would want at your fingertips when accessing the PIRLA data. h...

  16. Genetics Home Reference: WAGR syndrome

    MedlinePlus

    ... signs and symptoms of WAGR syndrome can include childhood-onset obesity, inflammation of the pancreas (pancreatitis), and kidney failure. When WAGR syndrome includes childhood-onset obesity, it is often referred to as WAGRO syndrome. ...

  17. Genetics Home Reference: isolated hyperchlorhidrosis

    MedlinePlus

    ... is characterized by the excessive loss of salt (sodium chloride or NaCl) in sweat. In particular, "hyperchlorhidrosis" refers ... levels of chloride found in sweat, although both sodium and chloride are released. Because the salt is abnormally released ...

  18. Sports Reference: A Core Collection.

    ERIC Educational Resources Information Center

    Safford, Barbara Ripp

    2003-01-01

    Discusses reasons for including sports books in school library reference collections, explains why they should not be found only in public library collections, and provides six annotated bibliographies of sports books suitable for intermediate or middle school library collections. (LRW)

  19. Improved ultrasonic standard reference blocks

    NASA Technical Reports Server (NTRS)

    Eitzen, D. G.

    1975-01-01

    A program to improve the quality, reproducibility and reliability of nondestructive testing through the development of improved ASTM-type ultrasonic reference standards is described. Reference blocks of aluminum, steel, and titanium alloys were considered. Equipment representing the state-of-the-art in laboratory and field ultrasonic equipment was obtained and evaluated. Some RF and spectral data on ten sets of ultrasonic reference blocks were taken as part of a task to quantify the variability in response from nominally identical blocks. Techniques for residual stress, preferred orientation, and microstructural measurements were refined and are applied to a reference block rejected by the manufacturer during fabrication in order to evaluate the effect of metallurgical condition on block response.

  20. Space Station reference configuration description

    NASA Technical Reports Server (NTRS)

    1984-01-01

    The data generated by the Space Station Program Skunk Works over a period of 4 months which supports the definition of a Space Station reference configuration is documented. The data were generated to meet these objectives: (1) provide a focal point for the definition and assessment of program requirements; (2) establish a basis for estimating program cost; and (3) define a reference configuration in sufficient detail to allow its inclusion in the definition phase Request for Proposal (RFP).

  1. Virtual reference: chat with us!

    PubMed

    Lapidus, Mariana; Bond, Irena

    2009-01-01

    Virtual chat services represent an exciting way to provide patrons of medical libraries with instant reference help in an academic environment. The purpose of this article is to examine the implementation, marketing process, use, and development of a virtual reference service initiated at the Massachusetts College of Pharmacy and Health Sciences and its three-campus libraries. In addition, this paper will discuss practical recommendations for the future improvement of the service. PMID:19384714

  2. Virtual Reference Interferometry: Theory & Experiment

    NASA Astrophysics Data System (ADS)

    Galle, Michael Anthony

    This thesis introduces the idea that a simulated interferogram can be used as a reference for an interferometer. This new concept represents a paradigm shift from the conventional thinking, where a reference is the phase of a wavefront that traverses a known path. The simulated interferogram used as a reference is called a virtual reference. This thesis develops the theory of virtual reference interferometry and uses it for the characterization of chromatic dispersion in short length (<1m) fibers and optical components. Characterization of chromatic dispersion on short length fiber and optical components is a very difficult challenge. Accurate measurement of first and second order dispersion is important for applications from optical component design to nonlinear photonics, sensing and communications. Techniques for short-length dispersion characterization are therefore critical to the development of many photonic systems. The current generation of short-length dispersion measurement techniques are either easy to operate but lack sufficient accuracy, or have sufficient accuracy but are difficult to operate. The use of a virtual reference combines the advantages of these techniques so that it is both accurate and easy to operate. Chromatic dispersion measurements based on virtual reference interferometry have similar accuracy as the best conventional measurement techniques due to the ability to measure first and second order dispersion directly from the interference pattern. Unique capabilities of virtual reference interferometry are demonstrated, followed by a derivation of the operational constraints and system parameters. The technique is also applied to the characterization of few-mode fibers, a hot topic in telecommunications research where mode division multiplexing promises to expand network bandwidth. Also introduced is the theory of dispersive virtual reference interferometry, which can be used to overcome the bandwidth limitations associated with the

  3. Sequence Factorization with Multiple References

    PubMed Central

    Wandelt, Sebastian; Leser, Ulf

    2015-01-01

    The success of high-throughput sequencing has lead to an increasing number of projects which sequence large populations of a species. Storage and analysis of sequence data is a key challenge in these projects, because of the sheer size of the datasets. Compression is one simple technology to deal with this challenge. Referential factorization and compression schemes, which store only the differences between input sequence and a reference sequence, gained lots of interest in this field. Highly-similar sequences, e.g., Human genomes, can be compressed with a compression ratio of 1,000:1 and more, up to two orders of magnitude better than with standard compression techniques. Recently, it was shown that the compression against multiple references from the same species can boost the compression ratio up to 4,000:1. However, a detailed analysis of using multiple references is lacking, e.g., for main memory consumption and optimality. In this paper, we describe one key technique for the referential compression against multiple references: The factorization of sequences. Based on the notion of an optimal factorization, we propose optimization heuristics and identify parameter settings which greatly influence 1) the size of the factorization, 2) the time for factorization, and 3) the required amount of main memory. We evaluate a total of 30 setups with a varying number of references on data from three different species. Our results show a wide range of factorization sizes (optimal to an overhead of up to 300%), factorization speed (0.01 MB/s to more than 600 MB/s), and main memory usage (few dozen MB to dozens of GB). Based on our evaluation, we identify the best configurations for common use cases. Our evaluation shows that multi-reference factorization is much better than single-reference factorization. PMID:26422374

  4. National Nutrition Education Clearing House Reference List, General Teacher References.

    ERIC Educational Resources Information Center

    National Nutrition Education Clearing House, Berkeley, CA.

    References applicable to both elementary and secondary levels, as well as background information of importance to teachers in the field of nutrition and nutrition education, are included in this bibliography. Although not a comprehensive list, resources include books, pamphlets, curriculum guides, bibliographies, newsletters, article reprints, and…

  5. Reference and Reference Failures. Technical Report No. 398.

    ERIC Educational Resources Information Center

    Goodman, Bradley A.

    In order to build robust natural language processing systems that can detect and recover from miscommunication, the investigation of how people communicate and how they recover from problems in communication described in this artificial intelligence report focused on reference problems which a listener may have in determining what or whom a…

  6. Virtual Reference, Real Money: Modeling Costs in Virtual Reference Services

    ERIC Educational Resources Information Center

    Eakin, Lori; Pomerantz, Jeffrey

    2009-01-01

    Libraries nationwide are in yet another phase of belt tightening. Without an understanding of the economic factors that influence library operations, however, controlling costs and performing cost-benefit analyses on services is difficult. This paper describes a project to develop a cost model for collaborative virtual reference services. This…

  7. Reference Anytime Anywhere: Towards Virtual Reference Services at Penn State.

    ERIC Educational Resources Information Center

    Moyo, Lesley M.

    2002-01-01

    Outlines the service rationale, software and technology considerations taken by the Pennsylvania State University library in planning towards online, real-time reference services and provides an overview of the planned pilot project. Discusses recent trends in academic electronic libraries, including providing value-added services to support…

  8. Ce isotope systematics of island arc lavas from the Lesser Antilles

    NASA Astrophysics Data System (ADS)

    Bellot, Nina; Boyet, Maud; Doucelance, Régis; Pin, Christian; Chauvel, Catherine; Auclair, Delphine

    2015-11-01

    The La-Ce systematics has one of the longest half-lifes (T1/2 = 292.5 Ga) of radioactive decay systems used in isotope geochemistry. Variations of the 138Ce/142Ce ratio are expected to be small and the use of Ce as isotopic tracer requires a very precise measurement. Compared to Sm-Nd studies, the La-Ce decay system can provide additional information about the nature of sediments recycled in subduction zones, because unusually large Ce anomalies relative to the neighboring rare earth elements exist in marine sediments such as fish teeth or hydrothermal deposits. Here, we present a chemical purification technique for Ce, and mass spectrometric technique to perform accurate and reproducible analyses of Ce isotopes of natural samples. We report a large set of Ce isotope data including analysis of 2 Ce reference material solutions (AMES and JMC-304), 2 rock standards (BCR-2 and BHVO-2), 2 chondrites (the carbonaceous chondrite Allende and the enstatite chondrite Sahara 97072), 4 mid-ocean ridge basalts, 30 arc lavas from the Martinique Island and 5 oceanic sediments from DSDP-site 144 drilled on the Demerara rise. The long-term, external precision obtained on the AMES reference material is 80 ppm (2 s.d., 138Ce/142Ce = 0.0225732 ± 18, n = 89). However, we note an evolution of isotopic ratios measured in static mode over the duration of this study (33 months). When the reproducibility is calculated from the AMES reference material measured during the same analytical session, it averages 40 ppm. All the 138Ce/142Ce ratios have been normalized to the AMES value of 0.0225746 (measured in session 7, 2 s.d. = 14 ppm, n = 8), a session during which the chondritic value has been defined and the peak tailing was negligible. The 138Ce/142Ce ratio measured for the JMC-304 Ce reference reagent is 0.0225706 ± 9 (2 s.d. = 38 ppm, n = 10). The analytical precision on natural samples is improved by a factor of about 4 in relation to previous studies on island arcs (Tanaka et al

  9. PIRLA DBMS quick reference guide

    SciTech Connect

    Smith, J.

    1991-11-01

    The handbook facilitates the use of the PIRLA (Paleoecological Investigation of Recent Lake Acidification) database retrievals by showing all possible inputs, outputs, ranges, and quick reference information that you would want at your fingertips when accessing the PIRLA data. The handbook assumes no prior knowledge of PIRLA or SIR (a database management system), although a basic familiarity with computers is helpful. The PIRLA Data Base Management System User's Manual is recommended for reference, much additional detail, description of the intrinsic structure of the PIRLA database, and how it is set up under SIR.

  10. Reference Resources on the Web.

    ERIC Educational Resources Information Center

    Sherman, Chris

    2000-01-01

    Compares three Web-based online reference services that are described as a cross between a traditional database service and a Web search engine: Ask Jeeves (http://www.ask.com), The Electric Library (http://www.elibrary.com), and Information Please (http://www.infoplease.com). Concludes that each has strengths and weaknesses and aren't directly…

  11. Ontario. Reference Series No. 29.

    ERIC Educational Resources Information Center

    Department of External Affairs, Ottawa (Ontario).

    This booklet, one of a series featuring the Canadian provinces, presents a brief overview of Ontario and is suitable for teacher reference or student reading. Separate sections discuss geography, climate, history, agriculture, forestry, fishing, mining, manufacturing, transportation, energy, arts and culture, sports and recreation, and people and…

  12. Manitoba. Reference Series No. 28.

    ERIC Educational Resources Information Center

    Department of External Affairs, Ottawa (Ontario).

    This booklet, one of a series featuring the Canadian provinces, presents a brief overview of Manitoba and is suitable for teacher reference or student reading. Separate sections discuss agriculture, mining, energy, transportation and communication, fishing, forestry, fur trapping, health and social services, education, and political life. Specific…

  13. The Principal and Reference Letters.

    ERIC Educational Resources Information Center

    Smith, Agnes E.; Permuth, Steve; Gray, David L.

    1999-01-01

    Requests to write letters of reference for former teachers can be legally problematic. Principals should know relevant state laws; have employees sign a release from liability; provide only factual information; maintain fair personnel files; avoid telephone recommendations; disclose information on a need-to-know basis; and avoid performance…

  14. Tractor Transmissions. A Teaching Reference.

    ERIC Educational Resources Information Center

    American Association for Agricultural Engineering and Vocational Agriculture, Athens, GA.

    The manual was developed as a reference for teaching students about transmissions in farm tractors. The manual is divided into five sections: (1) transmission history, (2) gears and bearings in transmission, (3) sliding-gear transmissions, (4) planetary gearing, and (5) glossary. The working principles of the sliding-gear transmission, the most…

  15. Expert Systems in Reference Services.

    ERIC Educational Resources Information Center

    Roysdon, Christine, Ed.; White, Howard D., Ed.

    1989-01-01

    Eleven articles introduce expert systems applications in library and information science, and present design and implementation issues of system development for reference services. Topics covered include knowledge based systems, prototype development, the use of artificial intelligence to remedy current system inadequacies, and an expert system to…

  16. Mobile Technologies and Roving Reference

    ERIC Educational Resources Information Center

    Penner, Katherine

    2011-01-01

    As 21st century librarians, we have made apt adjustments for reaching out into the digital world, but we need to consider the students who still use library services within our walls. We can use available handheld, mobile technologies to help patrons too shy to approach the desk and free library staff to bring reference service directly to patrons.

  17. Usenet as a Reference Tool.

    ERIC Educational Resources Information Center

    Klassen, Tim W.

    1995-01-01

    Describes Usenet, an Internet service that provides access to computerized discussion groups, and examines how it can be used as a reference tool. Topics include subject groups, appropriate questions, exhausting local resources before posting, explaining Usenet to patrons, sending the question, and evaluating the answer. (AEF)

  18. Space Station reference configuration update

    NASA Technical Reports Server (NTRS)

    Bonner, Tom F., Jr.

    1985-01-01

    The reference configuration of the NASA Space Station as of November 1985 is presented in a series of diagrams, drawings, graphs, and tables. The configurations for components to be contributed by ESA, Canada, and Japan are included. Brief captions are provided, along with answers to questions raised at the conference.

  19. A Computerized Reference Retrieval System.

    ERIC Educational Resources Information Center

    Harline, N. La Var

    An automated retrieval system for reference works was constructed as a prototype in order to illustrate the capabilities and potentialities of future retrieval systems. More than 170 biographical works were indexed and stored in a computer disk to form a biographical data base, and a computer program was written to match patron queries. Consistent…

  20. When Is Cataphoric Reference Recognised?

    ERIC Educational Resources Information Center

    Filik, Ruth; Sanford, Anthony J.

    2008-01-01

    Pronouns typically have explicit antecedents in the prior discourse otherwise processing difficulty is experienced. However, it has been argued [Gordon, P. C., & Hendrick, R. (1997). "Intuitive knowledge of linguistic co-reference." "Cognition, 62", 325-370; Gordon, P. C., & Hendrick, R. (1998). "The representation and processing of co-reference…

  1. Range reference atmosphere Shemya, Alaska

    NASA Astrophysics Data System (ADS)

    1991-08-01

    A reference atmosphere is a statistical model of the earth's atmosphere, derived from upper air observations over a specific location. The individual RRA is the authoritative source for upper atmosphere climatology over the launch and recovery site for which it has been prepared. The RRA's are used to plan, evaluate, and establish environmental launch constraints for aerospace vehicles launched from a particular location.

  2. Quebec. Reference Series No. 30.

    ERIC Educational Resources Information Center

    Department of External Affairs, Ottawa (Ontario).

    This booklet, one of a series featuring the Canadian provinces, presents a brief overview of Quebec and is suitable for teacher reference or student reading. Separate sections discuss geography, climate, population, history, political history, recent politics, agriculture, forestry, mining, manufacturing and industry, hydroelectric power,…

  3. Selected Reference Books of 2000.

    ERIC Educational Resources Information Center

    McIlvaine, Eileen

    2001-01-01

    This annotated bibliography, a semiannual series, presents a selection of recent scholarly and general reference works, published in 2000. Works are in the following areas: dictionaries; religion; literature; film; music; political science; history; archaeology; and science and technology. New editions of standard works are highlighted at the end.…

  4. Saskatchewan. Reference Series No. 27.

    ERIC Educational Resources Information Center

    Department of External Affairs, Ottawa (Ontario).

    This booklet, one of a series featuring the Canadian provinces, presents a brief overview of Saskatchewan and is suitable for teacher reference or student reading. Separate sections discuss history, economy, oil, uranium, potash, coal, minerals and metals, agriculture, forestry, tourism and recreation, arts and culture, and people. Specific topics…

  5. REFERENCE SITE WATERSHED DELINEATION PROJECT

    EPA Science Inventory

    The use of geographic information systems for the delineation of watersheds and analysis of land use / land cover associated with 250 reference sites on wadeable streams as identified by the Central Plains Bioassessment workgroup and located in the States of Kansas, Iowa, Missour...

  6. Reference As Others Do It.

    ERIC Educational Resources Information Center

    Coffman, Steve

    1999-01-01

    Describes customer call centers that provide customer service and support in business and considers how their routines could be adapted to library operations. Topics include centralized staff; interactive voice response; automated call distribution; question analysis; sophisticated software; training and monitoring; telephone reference; and…

  7. Reference Services in Developing Countries.

    ERIC Educational Resources Information Center

    Velho Lopes, Roseanne R.

    1992-01-01

    Discusses the development of reference services in developing countries and describes some of the functions of libraries and information services. Topics discussed include meeting users' needs; criteria for the planning and organization of services; and technology, including electronic dictionaries, computerized community information files,…

  8. Newfoundland. Reference Series No. 34.

    ERIC Educational Resources Information Center

    Department of External Affairs, Ottawa (Ontario).

    This booklet, one of a series featuring the Canadian provinces, presents a brief overview of Newfoundland and is suitable for teacher reference or student reading. Separate sections discuss geography and climate, history, economy, population and settlement, arts and culture, leisure and recreation, and heritage. Specific topics include the…

  9. Guam and Micronesia Reference Sources.

    ERIC Educational Resources Information Center

    Goetzfridt, Nicholas J.; Goniwiecha, Mark C.

    1993-01-01

    This article lists reference sources for studying Guam and Micronesia. The entries are arranged alphabetically by main entry within each section in the categories of: (1) bibliographical works; (2) travel and guide books; (3) handbooks and surveys; (4) dictionaries; (5) yearbooks; (6) periodical and newspaper publications; and (7) audiovisual…

  10. Alberta. Reference Series No. 26.

    ERIC Educational Resources Information Center

    Department of External Affairs, Ottawa (Ontario).

    This booklet, one of a series featuring the Canadian provinces, presents a brief overview of Alberta and is suitable for teacher reference or student reading. Separate sections discuss the history and population, the provincial government, the economy, transportation, communications, mineral resources, agriculture, manufacturing, forest products,…

  11. Bibliographies, Reference Works, and Archives.

    ERIC Educational Resources Information Center

    Elliott, Clark A.

    1985-01-01

    Explores the history of science in America from the viewpoint of access to sources. Considered are a number of specific bibliographic and other reference works, as well as important recent projects and developments that aim to preserve and improve access to archival and other documentation and historical data for future use. (JN)

  12. Reference Effectiveness: A Review of Research.

    ERIC Educational Resources Information Center

    Powell, Ronald R.

    1984-01-01

    This research review analyzes output measures that assess the effectiveness of a library's reference services: reference questions, reference staff performance, reference users, combined output measures, and combined input/output measures. The need for research, a definition of reference effectiveness, and input measures are noted. Seventy-three…

  13. A Staffing Model for Telephone Reference Operations

    ERIC Educational Resources Information Center

    Sampson, Gary S.

    1978-01-01

    A model is provided for staffing telephone reference operations which allow for the balancing of staffing requirements and reference delivery standards. Telephone service is assumed, but it should be equally applicable to any reference queuing situation. (Author)

  14. The Calibration Reference Data System

    NASA Astrophysics Data System (ADS)

    Greenfield, P.; Miller, T.

    2016-07-01

    We describe a software architecture and implementation for using rules to determine which calibration files are appropriate for calibrating a given observation. This new system, the Calibration Reference Data System (CRDS), replaces what had been previously used for the Hubble Space Telescope (HST) calibration pipelines, the Calibration Database System (CDBS). CRDS will be used for the James Webb Space Telescope (JWST) calibration pipelines, and is currently being used for HST calibration pipelines. CRDS can be easily generalized for use in similar applications that need a rules-based system for selecting the appropriate item for a given dataset; we give some examples of such generalizations that will likely be used for JWST. The core functionality of the Calibration Reference Data System is available under an Open Source license. CRDS is briefly contrasted with a sampling of other similar systems used at other observatories.

  15. The International Celestial Reference System

    NASA Astrophysics Data System (ADS)

    Fomalont, E.

    2016-05-01

    The International Celestial Reference System (ICRS) is a set of prescriptions, conventions, observational techniques and modeling required to define an celestial inertial frame. The origin of the frame is the solar-system barycenter. The ICRS was adopted by the International Astronomical Union in 1997 as the replacement of the FK5 system. The frame is called the International Celestial Reference Frame (ICRF), and is realized (defined) by the accurate position of 295 radio sources, distributed over the sky, and the accuracy of the frame orientation is about 10 microarcsec. This review will cover: the history of the development of the ICRS; the basics of the major observational technique of Very Long Baseline Interferometry; the use of the fundamental observable, the group delay; experimental strategies to optimize the accuracy; the computational methods for analyzing the large data base; the two major error limitations; and the possible of ICRS/Gaia interactions.

  16. HANFORD WASTE MINERALOGY REFERENCE REPORT

    SciTech Connect

    DISSELKAMP RS

    2010-06-29

    This report lists the observed mineral phases present in the Hanford tanks. This task was accomplished by performing a review of numerous reports that used experimental techniques including, but not limited to: x-ray diffraction, polarized light microscopy, scanning electron microscopy, transmission electron microscopy, energy dispersive spectroscopy, electron energy loss spectroscopy, and particle size distribution analyses. This report contains tables that can be used as a quick reference to identify the crystal phases observed in Hanford waste.

  17. HANFORD WASTE MINEROLOGY REFERENCE REPORT

    SciTech Connect

    DISSELKAMP RS

    2010-06-18

    This report lists the observed mineral phase phases present in the Hanford tanks. This task was accomplished by performing a review of numerous reports using experimental techniques including, but not limited to: x-ray diffraction, polarized light microscopy, scanning electron microscopy, transmission electron microscopy, energy dispersive spectroscopy, electron energy loss spectroscopy, and particle size distribution analyses. This report contains tables that can be used as a quick reference to identify the crystal phases present observed in Hanford waste.

  18. National Software Reference Library (NSRL)

    National Institute of Standards and Technology Data Gateway

    National Software Reference Library (NSRL) (PC database for purchase)   A collaboration of the National Institute of Standards and Technology (NIST), the National Institute of Justice (NIJ), the Federal Bureau of Investigation (FBI), the Defense Computer Forensics Laboratory (DCFL),the U.S. Customs Service, software vendors, and state and local law enforement organizations, the NSRL is a tool to assist in fighting crime involving computers.

  19. Microgrid cyber security reference architecture.

    SciTech Connect

    Veitch, Cynthia K.; Henry, Jordan M.; Richardson, Bryan T.; Hart, Derek H.

    2013-07-01

    This document describes a microgrid cyber security reference architecture. First, we present a high-level concept of operations for a microgrid, including operational modes, necessary power actors, and the communication protocols typically employed. We then describe our motivation for designing a secure microgrid; in particular, we provide general network and industrial control system (ICS)-speci c vulnerabilities, a threat model, information assurance compliance concerns, and design criteria for a microgrid control system network. Our design approach addresses these concerns by segmenting the microgrid control system network into enclaves, grouping enclaves into functional domains, and describing actor communication using data exchange attributes. We describe cyber actors that can help mitigate potential vulnerabilities, in addition to performance bene ts and vulnerability mitigation that may be realized using this reference architecture. To illustrate our design approach, we present a notional a microgrid control system network implementation, including types of communica- tion occurring on that network, example data exchange attributes for actors in the network, an example of how the network can be segmented to create enclaves and functional domains, and how cyber actors can be used to enforce network segmentation and provide the neces- sary level of security. Finally, we describe areas of focus for the further development of the reference architecture.

  20. Reference Inflow Characterization for River Resource Reference Model (RM2)

    SciTech Connect

    Neary, Vincent S

    2011-12-01

    Sandia National Laboratory (SNL) is leading an effort to develop reference models for marine and hydrokinetic technologies and wave and current energy resources. This effort will allow the refinement of technology design tools, accurate estimates of a baseline levelized cost of energy (LCoE), and the identification of the main cost drivers that need to be addressed to achieve a competitive LCoE. As part of this effort, Oak Ridge National Laboratory was charged with examining and reporting reference river inflow characteristics for reference model 2 (RM2). Published turbulent flow data from large rivers, a water supply canal and laboratory flumes, are reviewed to determine the range of velocities, turbulence intensities and turbulent stresses acting on hydrokinetic technologies, and also to evaluate the validity of classical models that describe the depth variation of the time-mean velocity and turbulent normal Reynolds stresses. The classical models are found to generally perform well in describing river inflow characteristics. A potential challenge in river inflow characterization, however, is the high variability of depth and flow over the design life of a hydrokinetic device. This variation can have significant effects on the inflow mean velocity and turbulence intensity experienced by stationary and bottom mounted hydrokinetic energy conversion devices, which requires further investigation, but are expected to have minimal effects on surface mounted devices like the vertical axis turbine device designed for RM2. A simple methodology for obtaining an approximate inflow characterization for surface deployed devices is developed using the relation umax=(7/6)V where V is the bulk velocity and umax is assumed to be the near-surface velocity. The application of this expression is recommended for deriving the local inflow velocity acting on the energy extraction planes of the RM2 vertical axis rotors, where V=Q/A can be calculated given a USGS gage flow time

  1. Ultra-high-precision Nd-isotope measurements of geological materials by MC-ICPMS

    PubMed Central

    Saji, Nikitha Susan; Wielandt, Daniel; Paton, Chad; Bizzarro, Martin

    2016-01-01

    We report novel techniques allowing the measurement of Nd-isotope ratios with unprecedented accuracy and precision by multi-collector inductively coupled plasma mass spectrometry. Using the new protocol, we have measured the Nd-isotopic composition of rock and synthetic Nd standards as well as that of the Allende carbonaceous chondrite. Analyses of BCR-2, BHVO-2 and GSP-2 rock standards yield mass-independent compositions identical to the JNdi-1 Nd-reference standard, with an external reproducibility of 2.4, 1.6, 1.6 and 3.5 ppm respectively, on μ142Nd, μ145Nd, μ146Nd and μ150Nd (μ representing the ppm-deviation of the ratios from JNdi-1) using 148Nd/144Nd for internal normalization. This represents an improvement in precision by a factor of 2, 7 and 9 respectively for μ142Nd, μ145Nd and μ150Nd. Near-quantitative recovery from purification chemistry and sample-standard bracketing allow for the determination of mass-dependent Nd-isotopic composition of samples. Synthetic standards, namely La Jolla and AMES, record mass-dependent variability of up to 1.2 ε per atomic mass unit and mass-independent compositions resolvable by up to 3 ppm for μ142Nd and 8 ppm for μ150Nd, relative to JNdi-1. The mass-independent compositions are consistent with equilibrium mass fractionation during purification. The terrestrial rock standards define a uniform stable ε145Nd of −0.24 ± 0.19 (2SD) relative to JNdi-1, indistinguishable from the mean Allende ε145Nd of −0.19 ± 0.09. We consider this value to represent the mass-dependent Nd-isotope composition of Bulk Silicate Earth (BSE). The modest mass-dependent fractionation of JNdi-1 relative to BSE results in potential effects on mass-independent composition that cannot be resolved within the reproducibility of our analyses when correcting for natural and instrumental mass fractionation by kinetic law, making it a suitable reference standard for analysis of unknowns. Analysis of Allende (CV3) carbonaceous chondrite

  2. Coal fines consolidation. [269 references

    SciTech Connect

    Gunther, A.

    1984-06-01

    The primary objective of this study was to survey existing methods and techniques for consolidating coal fines into lump coal which would be suitable as feed to fixed bed gasifiers. Another objective was to characterize the properties of consolidated coal which would establish its suitability for use in such gasifiers. To accomplish these objectives, a search of the technical literature was conducted in the pertinent subject areas. In addition, a survey was made of industrial and research organizations which have been active in the field of coal consolidation. The literature search mainly covered the period from 1970 to the present, although certain basic references were dated in the early 1900's. Approximately 250 from a total of about 1500 references were identified as relevant to the scope of this study. Information on coal consolidation was solicited from about thirty organizations and a response of about 50% was obtained. A review and evaluation of the relevant technical literature was made and is summarized, along with information provided by the survey responses, in the body of this report. Three primary methods for mechanically consolidating coal fines were identified; briquetting, pelletizing, and extrusion. Based on the limited experience reported, it appears that the technical feasibility of consolidating coal fines as feed to fixed bed gasifiers has been demonstrated. Costs for producing coal agglomerates, as reported in the literature, vary over a wide range, from about 7 to about 30 dollars per ton of product. The low cost range might be acceptable in terms of an overall gasification project but further effort is required to determine if such costs are attainable in practice. 269 references.

  3. Sentinel 2 global reference image

    NASA Astrophysics Data System (ADS)

    Dechoz, C.; Poulain, V.; Massera, S.; Languille, F.; Greslou, D.; de Lussy, F.; Gaudel, A.; L'Helguen, C.; Picard, C.; Trémas, T.

    2015-10-01

    Sentinel-2 is a multispectral, high-resolution, optical imaging mission, developed by the European Space Agency (ESA) in the frame of the Copernicus program of the European Commission. In cooperation with ESA, the Centre National d'Etudes Spatiales (CNES) is responsible for the image quality of the project, and will ensure the CAL/VAL commissioning phase. Sentinel-2 mission is devoted the operational monitoring of land and coastal areas, and will provide a continuity of SPOT- and Landsat-type data. Sentinel-2 will also deliver information for emergency services. Launched in 2015 and 2016, there will be a constellation of 2 satellites on a polar sun-synchronous orbit, imaging systematically terrestrial surfaces with a revisit time of 5 days, in 13 spectral bands in visible and shortwave infra-red. Therefore, multi-temporal series of images, taken under the same viewing conditions, will be available. So as to ensure for the multi-temporal registration of the products, specified to be better than 0.3 pixels at 2σ, a Global Reference Image (GRI) will be produced during the CAL/VAL period. This GRI is composed of a set of Sentinel-2 acquisitions, which geometry has been corrected by bundle block adjustment. During L1B processing, Ground Control Points will be taken between this reference image and the sentinel-2 acquisition processed and the geometric model of the image corrected, so as to ensure the good multi-temporal registration. This paper first details the production of the reference during the CALVAL period, and then details the qualification and geolocation performance assessment of the GRI. It finally presents its use in the Level-1 processing chain and gives a first assessment of the multi-temporal registration.

  4. PVWatts Version 1 Technical Reference

    SciTech Connect

    Dobos, A. P.

    2013-10-01

    The NREL PVWatts(TM) calculator is a web application developed by the National Renewable Energy Laboratory (NREL) that estimates the electricity production of a grid-connected photovoltaic system based on a few simple inputs. PVWatts combines a number of sub-models to predict overall system performance, and makes several hidden assumptions about performance parameters. This technical reference details the individual sub-models, documents assumptions and hidden parameters, and explains the sequence of calculations that yield the final system performance estimation.

  5. Background stratospheric aerosol reference model

    NASA Astrophysics Data System (ADS)

    McCormick, M. P.; Wang, Pi-Huan

    Nearly global SAGE I satellite observations in the nonvolcanic period from March 1979 to February 1980 are used to produce a reference background stratospheric aerosol optical model. Zonally average profiles of the 1.0-micron aerosol extinction for the tropics, midlatitudes, and high latitudes for both hemispheres are given in graphical and tabulated form for the different seasons. A third order polynomial fit to the vertical profile data set is used to derive analytic expressions for the seasonal global means and the yearly global mean. The results have application to the simulation of atmospheric radiative transfer and radiance calculations in atmospheric remote sensing.

  6. Reference electrode for electrolytic cell

    DOEpatents

    Kessie, R.W.

    1988-07-28

    A reference electrode device is provided for a high temperature electrolytic cell used to electrolytically recover uranium from spent reactor fuel dissolved in an anode pool, the device having a glass tube to enclose the electrode and electrolyte and serve as a conductive membrane with the cell electrolyte, and an outer metal tube about the glass tube to serve as a shield and basket for any glass sections broken by handling of the tube to prevent their contact with the anode pool, the metal tube having perforations to provide access between the bulk of the cell electrolyte and glass membrane. 4 figs.

  7. Electrolytic cell with reference electrode

    DOEpatents

    Kessie, Robert W.

    1989-01-01

    A reference electrode device is provided for a high temperature electrolytic cell used to electrolytically recover uranium from spent reactor fuel dissolved in an anode pool, the device having a glass tube to enclose the electrode and electrolyte and serve as a conductive membrane with the cell electrolyte, and an outer metal tube about the glass tube to serve as a shield and basket for any glass sections broken by handling of the tube to prevent their contact with the anode pool, the metal tube having perforations to provide access between the bulk of the cell electrolyte and glass membrane.

  8. Bibliography/1. Fine Arts Reference Books.

    ERIC Educational Resources Information Center

    Hauck, Alice; Markey, Karen

    This annotated bibliography of art reference books in the Eisenhower Library's Art Reference Department at Johns Hopkins University serves as the culmination of a joint venture between the General Reference Department and History of Art Department. The library's Art Reference room is adjacent to the Fine Arts stacks in the library and serves…

  9. The Art of Collection Development: Reference Style.

    ERIC Educational Resources Information Center

    Schmitt, John P.

    1998-01-01

    Discusses selecting for a reference collection, creative budgeting, cutting a deal, collection awareness (strengths/needs), Web site reviews, R-Net (reviews from diverse areas and institutions), and print vs. electronic reference products. Reference librarian adhere to high standards for reference book and Web sites, teach assessment techniques,…

  10. 40 CFR 1042.910 - Reference materials.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... reference as prescribed in 5 U.S.C. 552(a) and 1 CFR part 51. Anyone may inspect copies at the U.S. EPA, Air... 40 Protection of Environment 33 2014-07-01 2014-07-01 false Reference materials. 1042.910 Section... Other Reference Information § 1042.910 Reference materials. Documents listed in this section have...

  11. 40 CFR 1042.910 - Reference materials.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... reference as prescribed in 5 U.S.C. 552(a) and 1 CFR part 51. Anyone may inspect copies at the U.S. EPA, Air... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Reference materials. 1042.910 Section... Other Reference Information § 1042.910 Reference materials. Documents listed in this section have...

  12. Demonstrative Reference in Nepali: An Introduction.

    ERIC Educational Resources Information Center

    Giri, Ram Ashish

    The demonstratives in Napali are outlined, and their operation within the language system is analyzed. Demonstratives in Nepali are words used to refer to places, things, names, and activities. The reference may be endophoric (in which case the referents are in the text) or exophoric (in which case the referents are in the context or situation).…

  13. Instant Messaging Reference: How Does It Compare?

    ERIC Educational Resources Information Center

    Desai, Christina M.

    2003-01-01

    Compares a digital reference service that uses instant messaging with traditional, face-to-face reference based on experiences at the Southern Illinois University library. Addresses differences in reference questions asked, changes in the reference transaction, student expectations, bibliographic instruction, and librarian attitudes and procedures…

  14. Improving the Quality of Telephone Reference Service.

    ERIC Educational Resources Information Center

    Quinn, Brian

    1995-01-01

    Discusses telephone reference services in libraries. Topics include characteristics of quality phone reference; policies and guidelines for quality service; a survey of pertinent literature evaluating telephone reference; training; and technology for telephone reference, including cellular and cordless phones, electronic resources, and automated…

  15. Coastwide Reference Monitoring System (CRMS)

    USGS Publications Warehouse

    2010-01-01

    In 1990, the U.S. Congress enacted the Coastal Wetlands Planning, Protection and Restoration Act (CWPPRA) in response to growing awareness of a land loss crisis in Louisiana. Projects funded by CWPPRA require monitoring and evaluation of project effectiveness, and there is also a need to assess the cumulative effects of all projects to achieve a sustainable coastal environment. In 2003, the Louisiana Office of Coastal Protection and Restoration (OCPR) and the U.S. Geological Survey (USGS) received approval from the CWPPRA Task Force to implement the Coastwide Reference Monitoring System (CRMS) as a mechanism to monitor and evaluate the effectiveness of CWPPRA projects at the project, region, and coastwide levels. The CRMS design implements a multiple reference approach by using aspects of hydrogeomorphic functional assessments and probabilistic sampling. The CRMS program is as dynamic as the coastal habitats it monitors. The program is currently funded through CWPPRA and provides data for a variety of user groups, including resource managers, academics, landowners, and researchers.

  16. Nuclear structure references coding manual

    SciTech Connect

    Ramavataram, S.; Dunford, C.L.

    1984-02-01

    This manual is intended as a guide to Nuclear Structure References (NSR) compilers. The basic conventions followed at the National Nuclear Data Center (NNDC), which are compatible with the maintenance and updating of and retrieval from the Nuclear Structure References (NSR) file, are outlined. The structure of the NSR file such as the valid record identifiers, record contents, text fields as well as the major topics for which (KEYWORDS) are prepared are ennumerated. Relevant comments regarding a new entry into the NSR file, assignment of (KEYNO ), generation of (SELECTRS) and linkage characteristics are also given. A brief definition of the Keyword abstract is given followed by specific examples; for each TOPIC, the criteria for inclusion of an article as an entry into the NSR file as well as coding procedures are described. Authors submitting articles to Journals which require Keyword abstracts should follow the illustrations. The scope of the literature covered at NNDC, the categorization into Primary and Secondary sources, etc. is discussed. Useful information regarding permitted character sets, recommended abbreviations, etc. is given.

  17. Event boundaries and anaphoric reference.

    PubMed

    Thompson, Alexis N; Radvansky, Gabriel A

    2016-06-01

    The current study explored the finding that parsing a narrative into separate events impairs anaphor resolution. According to the Event Horizon Model, when a narrative event boundary is encountered, a new event model is created. Information associated with the prior event model is removed from working memory. So long as the event model containing the anaphor referent is currently being processed, this information should still be available when there is no narrative event boundary, even if reading has been disrupted by a working-memory-clearing distractor task. In those cases, readers may reactivate their prior event model, and anaphor resolution would not be affected. Alternatively, comprehension may not be as event oriented as this account suggests. Instead, any disruption of the contents of working memory during comprehension, event related or not, may be sufficient to disrupt anaphor resolution. In this case, reading comprehension would be more strongly guided by other, more basic language processing mechanisms and the event structure of the described events would play a more minor role. In the current experiments, participants were given stories to read in which we included, between the anaphor and its referent, either the presence of a narrative event boundary (Experiment 1) or a narrative event boundary along with a working-memory-clearing distractor task (Experiment 2). The results showed that anaphor resolution was affected by narrative event boundaries but not by a working-memory-clearing distractor task. This is interpreted as being consistent with the Event Horizon Model of event cognition. PMID:26452376

  18. Reference ballistic imaging database performance.

    PubMed

    De Kinder, Jan; Tulleners, Frederic; Thiebaut, Hugues

    2004-03-10

    Ballistic imaging databases allow law enforcement to link recovered cartridge cases to other crime scenes and to firearms. The success of these databases has led many to propose that all firearms in circulation be entered into a reference ballistic image database (RBID). To assess the performance of an RBID, we fired 4200 cartridge cases from 600 9mm Para Sig Sauer model P226 series pistols. Each pistol fired two Remington cartridges, one of which was imaged in the RBID, and five additional cartridges, consisting of Federal, Speer, Winchester, Wolf, and CCI brands. Randomly selected samples from the second series of Remington cartridge cases and from the five additional brands were then correlated against the RBID. Of the 32 cartridges of the same make correlated against the RBID, 72% ranked in the top 10 positions. Likewise, of the 160 cartridges of the five different brands correlated against the database, 21% ranked in the top 10 positions. Generally, the ranking position increased as the size of the RBID increased. We obtained similar results when we expanded the RBID to include firearms with the same class characteristics for breech face marks, firing pin impressions, and extractor marks. The results of our six queries against the RBID indicate that a reference ballistics image database of new guns is currently fraught with too many difficulties to be an effective and efficient law enforcement tool. PMID:15036442

  19. New SCIAMACHY Solar Reference Spectrum

    NASA Astrophysics Data System (ADS)

    Hilbig, Tina; Bramstedt, Klaus; Weber, Mark; Burrows, John P.

    2016-04-01

    The Scanning Imaging Absorption spectroMeter for Atmospheric CHartographY (SCIAMACHY) aboard ESA's ENVISAT satellite platform was operating from 2002 until 2012. It was designed to measure the radiance backscattered from the Earth and hence determine total columns and vertical profiles of atmospheric trace gas species. Furthermore SCIAMACHY performed daily sun observations via a diffuser. Solar spectra in the wavelength range from 212 nm to 1760 nm and two narrow bands from 1930 to 2040 nm and 2260 to 2380 nm are measured with a spectral resolution of 0,2 to 1,5 nm in the different channels. Recent developments in the SCIAMACHY calibration (e.g. a physical model of the scanner unit including degradation effects, and an on-ground to in-flight correction using the on-board white light source (WLS)) are used for the generation of a new SCIAMACHY solar reference spectrum as a first step towards a 10 years time series of solar spectral irradiance (SSI) data. For validation comparisons with other solar reference spectra are performed.

  20. High stability wavefront reference source

    DOEpatents

    Feldman, M.; Mockler, D.J.

    1994-05-03

    A thermally and mechanically stable wavefront reference source which produces a collimated output laser beam is disclosed. The output beam comprises substantially planar reference wavefronts which are useful for aligning and testing optical interferometers. The invention receives coherent radiation from an input optical fiber, directs a diverging input beam of the coherent radiation to a beam folding mirror (to produce a reflected diverging beam), and collimates the reflected diverging beam using a collimating lens. In a class of preferred embodiments, the invention includes a thermally and mechanically stable frame comprising rod members connected between a front end plate and a back end plate. The beam folding mirror is mounted on the back end plate, and the collimating lens mounted to the rods between the end plates. The end plates and rods are preferably made of thermally stable metal alloy. Preferably, the input optical fiber is a single mode fiber coupled to an input end of a second single mode optical fiber that is wound around a mandrel fixedly attached to the frame of the apparatus. The output end of the second fiber is cleaved so as to be optically flat, so that the input beam emerging therefrom is a nearly perfect diverging spherical wave. 7 figures.

  1. High stability wavefront reference source

    DOEpatents

    Feldman, Mark; Mockler, Daniel J.

    1994-01-01

    A thermally and mechanically stable wavefront reference source which produces a collimated output laser beam. The output beam comprises substantially planar reference wavefronts which are useful for aligning and testing optical interferometers. The invention receives coherent radiation from an input optical fiber, directs a diverging input beam of the coherent radiation to a beam folding mirror (to produce a reflected diverging beam), and collimates the reflected diverging beam using a collimating lens. In a class of preferred embodiments, the invention includes a thermally and mechanically stable frame comprising rod members connected between a front end plate and a back end plate. The beam folding mirror is mounted on the back end plate, and the collimating lens mounted to the rods between the end plates. The end plates and rods are preferably made of thermally stable metal alloy. Preferably, the input optical fiber is a single mode fiber coupled to an input end of a second single mode optical fiber that is wound around a mandrel fixedly attached to the frame of the apparatus. The output end of the second fiber is cleaved so as to be optically flat, so that the input beam emerging therefrom is a nearly perfect diverging spherical wave.

  2. SNAP operating system reference manual

    SciTech Connect

    Sabuda, J.D.; Polito, J.; Walker, J.L.; Grant, F.H. III

    1982-03-01

    The SNAP Operating System (SOS) is a FORTRAN 77 program which provides assistance to the safeguards analyst who uses the Safeguards Automated Facility Evaluation (SAFE) and the Safeguards Network Analysis Procedure (SNAP) techniques. Features offered by SOS are a data base system for storing a library of SNAP applications, computer graphics representation of SNAP models, a computer graphics editor to develop and modify SNAP models, a SAFE-to-SNAP interface, automatic generation of SNAP input data, and a computer graphic post-processor for SNAP. The SOS Reference Manual provides detailed application information concerning SOS as well as a detailed discussion of all SOS components and their associated command input formats. SOS was developed for the US Nuclear Regulatory Commission's Office of Nuclear Regulatory Research and the US Naval Surface Weapons Center by Pritsker and Associates, Inc., under contract to Sandia National Laboratories.

  3. Mars Human Exploration Reference Mission

    NASA Technical Reports Server (NTRS)

    Drake, Bret

    1998-01-01

    This presentation proposes the next steps for human exploration of Mars. The presentation reviews the reasons for human exploration of Mars. Two different trajectories are proposed: (1) for a long stay mission, and (2) for a short term mission, which could also include a swing by Venus. A reference mission scenario is investigated, which includes forward deployment of two cargo missions, followed by a human piloted mission. The power needs of such a mission include nuclear thermal propulsion, and the possible use of Mars in situ resources. The exploration will require electric propulsion, stationary power source, and a mobile power source. The trajectories required for electric propulsion of earth are shown, and the engineering of a Mars Transportation Habitat are reviewed.

  4. Background stratospheric aerosol reference model

    NASA Technical Reports Server (NTRS)

    Mccormick, M. P.; Wang, P.

    1989-01-01

    In this analysis, a reference background stratospheric aerosol optical model is developed based on the nearly global SAGE 1 satellite observations in the non-volcanic period from March 1979 to February 1980. Zonally averaged profiles of the 1.0 micron aerosol extinction for the tropics and the mid- and high-altitudes for both hemispheres are obtained and presented in graphical and tabulated form for the different seasons. In addition, analytic expressions for these seasonal global zonal means, as well as the yearly global mean, are determined according to a third order polynomial fit to the vertical profile data set. This proposed background stratospheric aerosol model can be useful in modeling studies of stratospheric aerosols and for simulations of atmospheric radiative transfer and radiance calculations in atmospheric remote sensing.

  5. Inertial pseudo star reference unit

    NASA Astrophysics Data System (ADS)

    Luniewicz, Michael F.; Woodbury, Dale T.; Gilmore, Jerold P.; Chien, Tze T.

    1994-05-01

    Advanced space systems for earth observation sensing and defense applications share a common objective: high-resolution monitoring. They require subsystems that accurately provide precise line-of-sight (LOS) pointing of the monitoring sensor with extreme jitter suppression and a precision attitude control system. To address this objective, Draper has developed a pointing system, the Inertial Pseudo Star Reference Unit (IPSRU). The IPSRU effort is a DARPA and SDI sponsored program at Draper under contract with the USAF Phillips Laboratory. The IPSRU implements a collimated light source mounted on a wide-band, extremely low-noise inertially stabilized platform. The collimated light beam becomes, in effect, a jitter-stabilized pseudo star. In addition, its direction in inertial space can be pointed at a precise rate by commands applied to the platform.

  6. NUCLEAR SCIENCE REFERENCES CODING MANUAL

    SciTech Connect

    WINCHELL,D.F.

    2007-04-01

    This manual is intended as a guide for Nuclear Science References (NSR) compilers. The basic conventions followed at the National Nuclear Data Center (NNDC), which are compatible with the maintenance and updating of and retrieval from the Nuclear Science References (NSR) file, are outlined. The NSR database originated at the Nuclear Data Project (NDP) at Oak Ridge National Laboratory as part of a project for systematic evaluation of nuclear structure data.1 Each entry in this computer file corresponds to a bibliographic reference that is uniquely identified by a Keynumber and is describable by a Topic and Keywords. It has been used since 1969 to produce bibliographic citations for evaluations published in Nuclear Data Sheets. Periodic additions to the file were published as the ''Recent References'' issues of Nuclear Data Sheets prior to 2005. In October 1980, the maintenance and updating of the NSR file became the responsibility of the NNDC at Brookhaven National Laboratory. The basic structure and contents of the NSR file remained unchanged during the transfer. In Chapter 2, the elements of the NSR file such as the valid record identifiers, record contents, and text fields are enumerated. Relevant comments regarding a new entry into the NSR file and assignment of a keynumber are also given in Chapter 2. In Chapter 3, the format for keyword abstracts is given followed by specific examples; for each TOPIC, the criteria for inclusion of an article as an entry into the NSR file as well as coding procedures are described. Authors preparing Keyword abstracts either to be published in a Journal (e.g., Nucl. Phys. A) or to be sent directly to NNDC (e.g., Phys. Rev. C) should follow the illustrations in Chapter 3. The scope of 1See W.B.Ewbank, ORNL-5397 (1978). the literature covered at the NNDC, the categorization into Primary and Secondary sources, etc., is discussed in Chapter 4. Useful information regarding permitted character sets, recommended abbreviations, etc., is

  7. Primary Atomic Clock Reference System

    NASA Technical Reports Server (NTRS)

    2001-01-01

    An artist's concept of the Primary Atomic Clock Reference System (PARCS) plarned to fly on the International Space Station (ISS). PARCS will make even more accurate atomic time available to everyone, from physicists testing Einstein's Theory of Relativity, to hikers using the Global Positioning System to find their way. In ground-based atomic clocks, lasers are used to cool and nearly stop atoms of cesium whose vibrations are used as the time base. The microgravity of space will allow the atoms to be suspended in the clock rather than circulated in an atomic fountain, as required on Earth. PARCS is being developed by the Jet Propulsion Laboratory with principal investigators at the National Institutes of Standards and Technology and the University of Colorado, Boulder. See also No. 0103191

  8. Primary Atomic Clock Reference System

    NASA Technical Reports Server (NTRS)

    2001-01-01

    An artist's concept of the Primary Atomic Clock Reference System (PARCS) plarned to fly on the International Space Station (ISS). PARCS will make even more accurate atomic time available to everyone, from physicists testing Einstein's Theory of Relativity, to hikers using the Global Positioning System to find their way. In ground-based atomic clocks, lasers are used to cool and nearly stop atoms of cesium whose vibrations are used as the time base. The microgravity of space will allow the atoms to be suspended in the clock rather than circulated in an atomic fountain, as required on Earth. PARCS is being developed by the Jet Propulsion Laboratory with principal investigators at the National Institutes of Standards and Technology and the University of Colorado, Boulder. See also No. 0100120.

  9. Argon Purification Reference and Recommendation

    SciTech Connect

    Wu, J.; /Fermilab

    1991-05-23

    This engineering note is a reference for future consideration on the purification of argon. The original concern was for the possibility of argon contamination from components in the cryostats over long-term storage. An argon purification system could also be useful for purifying the contents of the argon dewar. The general conclusion is that most of the systems researched are too expensive at this time, but the recommended choice would be Centorr Furnaces. There were three basic types of purification systems which were to be considered. The first was the molecular sieve. This method would have been the preferred one, because it was claimed that it could purify liquid argon, removing liquid oxygen from the argon. However, none of the commercial companies researched provided this type of purification for use with liquid argon. Most companies said that this type of purification was impossible, and tests at IB-4 confirmed this. The second system contained a copper oxide to remove gaseous oxygen from argon gas. The disadvantage of this system wass that the argon had to be heated to a gas, and then cooled back down to liquid. The third system was similar to the second, except that it used tungsten or another material like titanium. This system also needed to heat the argon to gas, however the advantage of this system was that it supposedly removed all contaminants, that is, everything except for inert gases. Of the three systems, the third is the type manufactured by Centorr Furnaces, which uses a titanium charge.

  10. Research Notes and Information References

    SciTech Connect

    Hartley, III, Dean S.

    1994-12-01

    The RNS (Research Notes System) is a set of programs and databases designed to aid the research worker in gathering, maintaining, and using notes taken from the literature. The sources for the notes can be books, journal articles, reports, private conversations, conference papers, audiovisuals, etc. The system ties the databases together in a relational structure, thus eliminating data redundancy while providing full access to all the information. The programs provide the means for access and data entry in a way that reduces the key-entry burden for the user. Each note has several data fields. Included are the text of the note, the subject classification (for retrieval), and the reference identification data. These data are divided into four databases: Document data - title, author, publisher, etc., fields to identify the article within the document; Note data - text and page of the note; Sublect data - subject categories to ensure uniform spelling for searches. Additionally, there are subsidiary files used by the system, including database index and temporary work files. The system provides multiple access routes to the notes, both structurally (access method) and topically (through cross-indexing). Output may be directed to a printer or saved as a file for input to word processing software.

  11. ILC cryogenic systems reference design

    SciTech Connect

    Peterson, T.J.; Geynisman, M.; Klebaner, A.; Theilacker, J.; Parma, V.; Tavian, L.; /CERN

    2008-01-01

    A Global Design Effort (GDE) began in 2005 to study a TeV scale electron-positron linear accelerator based on superconducting radio-frequency (RF) technology, called the International Linear Collider (ILC). In early 2007, the design effort culminated in a reference design for the ILC, closely based on the earlier TESLA design. The ILC will consist of two 250 GeV linacs, which provide positron-electron collisions for high energy physics research. The particle beams will be accelerated to their final energy in superconducting niobium RF cavities operating at 2 kelvin. At a length of about 12 km each, the main linacs will be the largest cryogenic systems in the ILC. Positron and electron sources, damping rings, and beam delivery systems will also have a large number and variety of other superconducting RF cavities and magnets, which require cooling at liquid helium temperatures. Ten large cryogenic plants with 2 kelvin refrigeration are envisioned to cool the main linacs and the electron and positron sources. Three smaller cryogenic plants will cool the damping rings and beam delivery system components predominately at 4.5 K. This paper describes the cryogenic systems concepts for the ILC.

  12. The Lyman alpha reference sample

    NASA Astrophysics Data System (ADS)

    Adamo, Angela; Östlin, Göran; Hayes, Matthew; Melinder, Jens; Bik, Arjan

    2015-08-01

    The Lyman apha reference sample (LARS) is a major multiwavelength imaging and spectroscopic HST campaign of local normal star-forming galaxies, UV-luminous starburst systems, and luminous infrared galaxies. The aim of this survey is to probe what physical conditions and processes regulate the emission of Lyα radiation on local and global galactic scales. The Lyα line is widely used to identify and confirm galaxies in the distant universe, close to the epoch when the first galaxies formed and when the universe was reionized. However, the fact that Lyα is a resonant line makes it optically thick even at relatively low neutral hydrogen column densities, this means that the radiative transport of Lyα photons through galaxies is a complex problem where the structure, kinematics and dust content, and neutral hydrogen content of the interstellar medium all contribute to the process. In this poster we present the unique Lyα maps of the extended LARS sample (i.e. 42 galaxies). These initial results of the LARS survey reveal that when Lyα manages to escape it does so in the form of diffuse scattering halos.

  13. Ilc Cryogenic Systems Reference Design

    NASA Astrophysics Data System (ADS)

    Peterson, T. J.; Geynisman, M.; Klebaner, A.; Parma, V.; Tavian, L.; Theilacker, J.

    2008-03-01

    A Global Design Effort (GDE) began in 2005 to study a TeV scale electron-positron linear accelerator based on superconducting radio-frequency (RF) technology, called the International Linear Collider (ILC). In early 2007, the design effort culminated in a reference design for the ILC, closely based on the earlier TESLA design. The ILC will consist of two 250 GeV linacs, which provide positron-electron collisions for high energy physics research. The particle beams will be accelerated to their final energy in superconducting niobium RF cavities operating at 2 kelvin. At a length of about 12 km each, the main linacs will be the largest cryogenic systems in the ILC. Positron and electron sources, damping rings, and beam delivery systems will also have a large number and variety of other superconducting RF cavities and magnets, which require cooling at liquid helium temperatures. Ten large cryogenic plants with 2 kelvin refrigeration are envisioned to cool the main linacs and the electron and positron sources. Three smaller cryogenic plants will cool the damping rings and beam delivery system components predominately at 4.5 K. This paper describes the cryogenic systems concepts for the ILC.

  14. Research Notes and Information References

    Energy Science and Technology Software Center (ESTSC)

    1994-12-01

    The RNS (Research Notes System) is a set of programs and databases designed to aid the research worker in gathering, maintaining, and using notes taken from the literature. The sources for the notes can be books, journal articles, reports, private conversations, conference papers, audiovisuals, etc. The system ties the databases together in a relational structure, thus eliminating data redundancy while providing full access to all the information. The programs provide the means for access andmore » data entry in a way that reduces the key-entry burden for the user. Each note has several data fields. Included are the text of the note, the subject classification (for retrieval), and the reference identification data. These data are divided into four databases: Document data - title, author, publisher, etc., fields to identify the article within the document; Note data - text and page of the note; Sublect data - subject categories to ensure uniform spelling for searches. Additionally, there are subsidiary files used by the system, including database index and temporary work files. The system provides multiple access routes to the notes, both structurally (access method) and topically (through cross-indexing). Output may be directed to a printer or saved as a file for input to word processing software.« less

  15. Gender agreement and multiple referents

    PubMed Central

    Finocchiaro, Chiara; Mahon, Bradford Z.; Caramazza, Alfonso

    2010-01-01

    We report a new pattern of usage in current, spoken Italian that has implications for both psycholinguistic models of language production and linguistic theories of language change. In Italian, gender agreement is mandatory for both singular and plural nouns. However, when two or more nouns of different grammatical gender appear in a conjoined noun phrase (NP), masculine plural agreement is required. In this study, we combined on-line and off-line methodologies in order to assess the mechanisms involved in gender marking in the context of multiple referents. The results of two pronoun production tasks showed that plural feminine agreement was significantly more difficult than plural masculine agreement. In a separate study using offline judgements of acceptability, we found that agreement violations in Italian are tolerated more readily in the case of feminine conjoined noun phrases (e.g., la mela e la banana ‘the:fem apple:fem and the: fem banana: fem’) than masculine conjoined noun phrases (e.g., il fiore e il libro ‘the:mas flower: mas and the:mas book:mas’). Implications of these results are discussed both at the level of functional architecture within the language production system and at the level of changes in language use.* PMID:21037930

  16. Designing Optical Mark Forms for Reference Statistics.

    ERIC Educational Resources Information Center

    Hallman, Clark N.

    1981-01-01

    Presents a method for collecting reference desk statistics in machine-readable form using optical marks. Useful data categories are identified, and figures illustrate how data can be recorded for each category. Ten references are listed. (FM)

  17. Chinese-Mandarin Basic Course: References.

    ERIC Educational Resources Information Center

    Defense Language Inst., Monterey, CA.

    This is a collection of reference materials to be used with the Chinese-Mandarin Basic Course textbooks. This collection consists of information on romanization systems, indexes for reading and writing characters, and other tables for quick reference. (NCR)

  18. Independent Study Unit on Accelerated Reference Frames

    ERIC Educational Resources Information Center

    Poultney, S. K.

    1973-01-01

    Presents a list of topics, research areas, references, and laboratory equipment which is prepared to facilitate general-science students' understanding of physics aspects in accelerated reference frames after their study of circular motion and Galilean relativity in mechanics. (CC)

  19. Reference surfaces for bridge scour depths

    USGS Publications Warehouse

    Landers, Mark N.; Mueller, David S.

    1993-01-01

    Depth of scour is measured as the vertical distance between scoured channel geometry and a measurement reference surface. A scour depth measurement can have a wide range depending on the method used to establish the reference surface. A consistent method to establish reference surfaces for bridge scour measurements is needed to facilitate transferability of scour data an scour analyses. This paper describes and evaluates techniques for establishing reference surfaces from which local and contraction scour are measured.

  20. Lensless sensor system using a reference structure.

    PubMed

    Potuluri, Prasant; Gopinathan, Unnikrishnan; Adleman, James; Brady, David

    2003-04-21

    We describe a reference structure based sensor system for tracking the motion of an object. The reference structure is designed to implement a Hadamard transformation over a range of angular perspectives. We implemented a reference structure with an angular resolution of 5(o) and a field of view of 40(o). PMID:19461814

  1. 33 CFR 241.3 - References.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 33 Navigation and Navigable Waters 3 2013-07-01 2013-07-01 false References. 241.3 Section 241.3 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE FLOOD CONTROL COST-SHARING REQUIREMENTS UNDER THE ABILITY TO PAY PROVISION § 241.3 References. References cited in paragraphs (f) thru (i) may...

  2. Environmental Sciences Reference Sources. An Annotated Bibliography.

    ERIC Educational Resources Information Center

    McMartin, Mary I., Comp.

    This list of Environmental Sciences References Sources is intended to give undergraduate and graduate students a starting point when searching for information in the library. Entries are grouped according to type of reference material and then are listed in alphabetical order. The types of reference material included are guides to dictionaries,…

  3. Ties Between Celestial And Planetary Reference Frames

    NASA Technical Reports Server (NTRS)

    Finger, Mark H.; Folkner, William M.

    1992-01-01

    Report presents new determination of relative orientation (or frame tie) between reference frame of extra-galactic radio sources and reference frame of planetary ephemeris. Method employed for improved frame-tie estimate relies on ability to measure orientation of Earth with respect to inertial reference frame. Improves orbit determination for interplanetary spacecraft.

  4. 40 CFR 1043.100 - Reference materials.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... in 5 U.S.C. 552(a) and 1 CFR part 51. Anyone may inspect copies at the U.S. EPA, Air and Radiation... 40 Protection of Environment 33 2014-07-01 2014-07-01 false Reference materials. 1043.100 Section... § 1043.100 Reference materials. Documents listed in this section have been incorporated by reference...

  5. 40 CFR 1043.100 - Reference materials.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... in 5 U.S.C. 552(a) and 1 CFR part 51. Anyone may inspect copies at the U.S. EPA, Air and Radiation... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Reference materials. 1043.100 Section... § 1043.100 Reference materials. Documents listed in this section have been incorporated by reference...

  6. 33 CFR 277.3 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false References. 277.3 Section 277.3... References. (a) Section 6, Pub. L. 647, 67th Congress, 21 June 1940, as amended (33 U.S.C. 516). (Appendix A...) Coast Guard reference: COMDT (G-OPT-3), Exemplification-Principles of Apportionment of Cost...

  7. 32 CFR 861.1 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 6 2010-07-01 2010-07-01 false References. 861.1 Section 861.1 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE AIRCRAFT DEPARTMENT OF DEFENSE COMMERCIAL AIR TRANSPORTATION QUALITY AND SAFETY REVIEW PROGRAM § 861.1 References. The following references apply to this...

  8. 5 CFR 294.401 - References.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false References. 294.401 Section 294.401 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS AVAILABILITY OF OFFICIAL INFORMATION Cross References § 294.401 References. The table below provides assistance in locating other...

  9. 33 CFR 242.3 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false References. 242.3 Section 242.3 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE FLOOD PLAIN MANAGEMENT SERVICES PROGRAM ESTABLISHMENT OF FEES FOR COST RECOVERY § 242.3 References. The references...

  10. Frames of Reference in the Classroom

    ERIC Educational Resources Information Center

    Grossman, Joshua

    2012-01-01

    The classic film "Frames of Reference" effectively illustrates concepts involved with inertial and non-inertial reference frames. In it, Donald G. Ivey and Patterson Hume use the cameras perspective to allow the viewer to see motion in reference frames translating with a constant velocity, translating while accelerating, and rotating--all with…

  11. 40 CFR 312.11 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 27 2010-07-01 2010-07-01 false References. 312.11 Section 312.11 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SUPERFUND, EMERGENCY PLANNING, AND... Definitions and References § 312.11 References. The following industry standards may be used to comply...

  12. The Art of Reference Collection Development.

    ERIC Educational Resources Information Center

    Hattendorf, Lynn C.

    This paper argues that the first order of the day in reference collection development is to cope with the problems that developing user-responsive, client-centered reference collections always incur. It is suggested that the responsiveness of reference collections can be measured largely by the currency of the materials in the collection and by…

  13. Reference Service in an Academic Archives.

    ERIC Educational Resources Information Center

    O'Donnell, Frances

    2000-01-01

    Examines reference questions received at the archives of the Massachusetts Institute of Technology to determine why archival reference service is more time-consuming than standard academic library reference service. Also discusses differences in kinds of information and resources provided, arrangement of materials, and description and access.…

  14. Reference Service: A Thing of the Past?

    ERIC Educational Resources Information Center

    Berger, Christopher

    1996-01-01

    Argues that the traditional philosophy of public service has remained relevant and vital to overall library reference service despite information technology and other societal changes. Topics include information and information technology; and economic, political, and social trends as they influence reference librarians and reference service.…

  15. Reference Expertise: Paradigms, Strategies, and Systems.

    ERIC Educational Resources Information Center

    McCrank, Lawrence J.

    1993-01-01

    Explores the significance of expert system design for library reference services and library education, focusing on model logic and modeling for query analysis. The approaches of some graduate library schools are reviewed. Appendices included a decision-support module, a reference module component, and a typology of queries and reference tools.…

  16. Reference Services for Children and Young Adults.

    ERIC Educational Resources Information Center

    Reference Librarian, 1983

    1983-01-01

    This 25-article issue presents overview of reference services for childern and young adults, including public and school libraries, information needs, reference interviews, children's librarians, library instruction, library cooperation, production of information resources, material selection, and vertical files. References are included. (Haworth…

  17. 49 CFR 171.7 - Reference material.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... incorporation by reference by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR..., amendment 1 (2011). Table 1 to 49 CFR 171.7—Materials Not Incorporated by Reference Source and name of material 49 CFR reference American Biological Safety Association 1202 Allanson Road, Mundelein, IL...

  18. 49 CFR 171.7 - Reference material.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... incorporation by reference by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR..., into § 173.417. (2) Table 1 to 49 CFR 171.7—Materials Not Incorporated by Reference Source and name of material 49 CFR reference American Biological Safety Association 1202 Allanson Road, Mundelein, IL...

  19. 33 CFR 241.3 - References.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 33 Navigation and Navigable Waters 3 2011-07-01 2011-07-01 false References. 241.3 Section 241.3 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE FLOOD CONTROL COST-SHARING REQUIREMENTS UNDER THE ABILITY TO PAY PROVISION § 241.3 References. References cited in paragraphs (f) thru (i) may...

  20. 33 CFR 241.3 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false References. 241.3 Section 241.3 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE FLOOD CONTROL COST-SHARING REQUIREMENTS UNDER THE ABILITY TO PAY PROVISION § 241.3 References. References...

  1. Information/Reference Desk Procedures Manual.

    ERIC Educational Resources Information Center

    Helms, Cynthia Mae; Nelson, Judith

    This manual ensures that the personnel who work at the Information/Reference Desk of the James White Library, Andrews University carry out similar procedures regardless of their shift. It serves as an orientation tool and a reference guide, and gives procedures for dealing with patrons, answering reference questions, making the right referrals,…

  2. The Internet: A Ready Reference Library?

    ERIC Educational Resources Information Center

    Gabriel, Michael R.

    1998-01-01

    An academic librarian answered 24 questions using reference books, then tried to answer the same questions using an Internet search engine (Metacrawler). Evaluates the results of the Internet searches and discusses implications for library reference services and reference book publishers; Internet user expectations and satisfaction; and librarians…

  3. Communication Theory's Role in the Reference Interview.

    ERIC Educational Resources Information Center

    Glogoff, Stuart

    1983-01-01

    Notes the applicability of communication science theory to the reference process, particularly in areas involving human behavior, and discusses the roles of both verbal and nonverbal communication (body language, paralanguage, proxemics, and environmental factors) in the reference interview. Forty-one references are provided. (EJS)

  4. The reorganization of a monographic reference collection.

    PubMed

    Jeuell, C A

    1976-07-01

    Reference monographs in the Health Sciences Library of the College of Medicine and Dentistry of New Jersey were reorganized recently according to form, in order to enable both librarians and patrons to utilize these materials more efficiently. This reorganization reflects the unique characteristics of reference books as differentiated from the regular monographic collection, since reference materials are frequently consulted for quick "look-ups." A reference category scheme was developed and implemented, based on observations of and comparisons with reference collections of eight medical libraries in the New York metropolitan area. The reorganization enhances the retrievability of materials from this collection. PMID:938775

  5. Reference data sets for testing metrology software

    NASA Astrophysics Data System (ADS)

    Kok, G. J. P.; Harris, P. M.; Smith, I. M.; Forbes, A. B.

    2016-08-01

    Many fields of metrology rely on calculations that are implemented in software. When such software is used to provide a measurement result, which is required to be traceable, it is necessary to recognise explicitly the software and show it to be operating correctly. An approach to testing the performance of calculation software is based on using reference pairs each of which comprises reference input data applied as input to the software and corresponding reference output data against which the output data of the software is compared. However, to make the reference pair useful for verifying and validating calculation software, information is needed about the numerical accuracy of the reference pair, the numerical sensitivity of the reference output data to perturbations in the reference input data, and the measurement uncertainty associated with the reference output data arising from simulated measurement uncertainty associated with the reference input data. Such information is important as a means to express quantitatively the quality of the reference pair as a numerical artefact to test calculation software, and as a basis for performance metrics to express quantitatively the numerical performance of software. In this paper these additional components of a reference data set are described, and various approaches to calculating them are discussed. An example, concerned with the calculation of the Gaussian (least-squares) best-fit plane to measured data, which is typical of calculations undertaken in coordinate metrology, is used to illustrate the ideas presented.

  6. Astrophysics of Reference Frame Tie Objects

    NASA Technical Reports Server (NTRS)

    Johnston, Kenneth J.; Boboltz, David; Fey, Alan Lee; Gaume, Ralph A.; Zacharias, Norbert

    2004-01-01

    The Astrophysics of Reference Frame Tie Objects Key Science program will investigate the underlying physics of SIM grid objects. Extragalactic objects in the SIM grid will be used to tie the SIM reference frame to the quasi-inertial reference frame defined by extragalactic objects and to remove any residual frame rotation with respect to the extragalactic frame. The current realization of the extragalactic frame is the International Celestial Reference Frame (ICRF). The ICRF is defined by the radio positions of 212 extragalactic objects and is the IAU sanctioned fundamental astronomical reference frame. This key project will advance our knowledge of the physics of the objects which will make up the SIM grid, such as quasars and chromospherically active stars, and relates directly to the stability of the SIM reference frame. The following questions concerning the physics of reference frame tie objects will be investigated.

  7. Acute reference doses: theory and practical approaches.

    PubMed

    Moretto, A

    2000-07-01

    The approach of the Joint Meeting on Pesticide Residues to the establishment of the acute reference dose for pesticides is presented and related issues are discussed. Three main points seem relevant when discussing the acute reference dose: (1) what compounds should have an acute reference dose, (2) what toxicological database is required for the establishment of an acute reference dose; (3) what safety factors are to be used. It is concluded that (1) groups of compounds that need an acute reference dose can be identified, whereas general rules for identifying groups not requiring an acute reference dose cannot be easily given; (2) studies from the standard toxicological database can often be used to allocate an acute reference dose and the usefulness of refinements (by requesting specific studies) should be evaluated after intake assessment; general rules on study requirements cannot be easily given; (3) more thought should be given to what safety factors apply in certain circumstances. PMID:10983586

  8. The JWST Calibration Reference Data System

    NASA Astrophysics Data System (ADS)

    Bushouse, H.; Greenfield, P.; Miller, T.

    2012-09-01

    The James Webb Space Telescope (JWST) Calibration Reference Data System (CRDS) will be used during the instrumental calibration phase of JWST data processing to select reference files (e.g. darks, flats, distortion models) to be used to calibrate each dataset. The CRDS will also be used in the delivery and management of reference files within the JWST data archive and to manage the rules that will be used to determine which files are to be used with each science dataset. The CRDS incorporates lessons learned from more than 20 years of use of the HST Calibration Database System (CDBS), allowing for easier management of the reference file mapping rules, web-based reference file delivery and retrieval procedures, on-line access by off-site users who are reprocessing their science data, and easier testing of new reference files in the operations environment.

  9. Writing More Informative Letters of Reference

    PubMed Central

    Wright, Scott M; Ziegelstein, Roy C

    2004-01-01

    Writing a meaningful and valuable letter of reference is not an easy task. Several factors influence the quality of any letter of reference. First, the accuracy and reliability of the writer's impressions and judgment depend on how well he knows the individual being described. Second, the writer's frame of reference, which is determined by the number of persons at the same level that he has worked with, will impact the context and significance of his beliefs and estimations. Third, the letter-writing skills of the person composing the letter will naturally affect the letter. To support the other components of a candidate's application, a letter of reference should provide specific examples of how an individual's behavior or attitude compares to a reference group and should assess “intangibles” that are hard to glean from a curriculum vitae or from test scores. This report offers suggestions that should help physicians write more informative letters of reference. PMID:15109330

  10. Bisphenol A polycarbonate as a reference material

    NASA Technical Reports Server (NTRS)

    Hilado, C. J.; Cumming, H. J.; Williams, J. B.

    1977-01-01

    Test methods require reference materials to standardize and maintain quality control. Various materials have been evaluated as possible reference materials, including a sample of bisphenol A polycarbonate without additives. Screening tests for relative toxicity under various experimental conditions were performed using male mice exposed to pyrolysis effluents over a 200-800 C temperature range. It was found that the bisphenol A polycarbonate served as a suitable reference material as it is available in large quantities, and does not significantly change with time.

  11. Resources and References for Earth Science Teachers

    ERIC Educational Resources Information Center

    Wall, Charles A.; Wall, Janet E.

    1976-01-01

    Listed are resources and references for earth science teachers including doctoral research, new textbooks, and professional literature in astronomy, space science, earth science, geology, meteorology, and oceanography. (SL)

  12. A reference printer and color management architecture

    NASA Astrophysics Data System (ADS)

    Green, P. J.

    2007-01-01

    A colour management strategy based on a reference printer and reference medium is described. Additional printers and media are then defined in terms of this reference printer. This makes it possible to estimate new transforms for a given a printer and media with no new measurements, even when there is no characterization data available for this combination of printer and media. A simple method of estimating the new transform was implemented and evaluated, and it was found to give good results when the target printing condition was similar in gamut and colorant primaries to the reference printer. This approach can be extended by applying more complex empirical models.

  13. Reference materials for new psychoactive substances.

    PubMed

    Archer, Roland P; Treble, Ric; Williams, Keith

    2011-01-01

    Historically, the appearance of new psychoactive materials (and hence the requirement for new reference standards) has been relatively slow. This position has now changed, with 101 new psychoactive substances reported to EMCDDA-Europol since 2006. The newly reported materials, and associated metabolites, require properly certified reference materials to permit reliable identification and quantification. The traditional approach and timescales of reference material production and certification are being increasingly challenged by the appearance of these new substances. Reference material suppliers have to adopt new strategies to meet the needs of laboratories. This situation is particularly challenging for toxicology standards as the metabolism of many of these substances is initially unknown. Reference material production often involves synthesis from first principles. While it is possible to synthesis these materials, there can be significant difficulties, from synthetic complexities through to the need to use controlled materials. These issues are examined through a discussion of the synthesis of cathinones. Use of alternative sources, including pharmaceutical impurity materials or internet sourced products, as starting materials for conversion into appropriately certified reference materials are also discussed. The sudden appearance and sometimes brief lifetime in the market place of many of these novel legal highs or research chemicals present commercial difficulties for reference material producers. The need for collaboration at all levels is highlighted as essential to rapid identification of requirements for new reference materials. National or international commissioning or support may also be required to permit reference material producers to recover their development costs. PMID:21744516

  14. 32 CFR 516.2 - References.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 32 National Defense 3 2011-07-01 2009-07-01 true References. 516.2 Section 516.2 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY AID OF CIVIL AUTHORITIES AND PUBLIC RELATIONS LITIGATION General § 516.2 References. Applicable publications and forms are listed in appendix A to...

  15. 36 CFR 328.3 - References.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 36 Parks, Forests, and Public Property 3 2013-07-01 2012-07-01 true References. 328.3 Section 328... SEAPLANE OPERATIONS AT CIVIL WORKS WATER RESOURCE DEVELOPMENT PROJECTS ADMINISTERED BY THE CHIEF OF ENGINEERS § 328.3 References. (a) Title 36 CFR, part 327, Rules and Regulations Governing Public Use...

  16. 32 CFR 625.3 - References.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 32 National Defense 3 2013-07-01 2013-07-01 false References. 625.3 Section 625.3 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY SUPPLIES AND EQUIPMENT SURFACE TRANSPORTATION-ADMINISTRATIVE VEHICLE MANAGEMENT § 625.3 References. (a) Title 31, U.S. Code, section 638. (b)...

  17. 32 CFR 625.3 - References.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 32 National Defense 3 2014-07-01 2014-07-01 false References. 625.3 Section 625.3 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY SUPPLIES AND EQUIPMENT SURFACE TRANSPORTATION-ADMINISTRATIVE VEHICLE MANAGEMENT § 625.3 References. (a) Title 31, U.S. Code, section 638. (b)...

  18. 32 CFR 625.3 - References.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 32 National Defense 3 2012-07-01 2009-07-01 true References. 625.3 Section 625.3 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY SUPPLIES AND EQUIPMENT SURFACE TRANSPORTATION-ADMINISTRATIVE VEHICLE MANAGEMENT § 625.3 References. (a) Title 31, U.S. Code, section 638. (b)...

  19. Color, Reference, and Expertise in Language Acquisition

    ERIC Educational Resources Information Center

    Clark, Eve V.

    2006-01-01

    In learning the meaning of a new term, children need to fix its reference, learn its conventional meaning, and discover the meanings with which it contrasts. To do this, children must attend to adult speakers--the experts--and to their patterns of use. In the domain of color, children need to identify color terms as such, fix the reference of each…

  20. Jewish Studies: A Guide to Reference Sources.

    ERIC Educational Resources Information Center

    McGill Univ., Montreal (Quebec). McLennan Library.

    An annotated bibliography to the reference sources for Jewish Studies in the McLennan Library of McGill University (Canada) is presented. Any titles in Hebrew characters are listed by their transliterated equivalents. There is also a list of relevant Library of Congress Subject Headings. General reference sources listed are: encyclopedias,…

  1. Guide to Children's Magazines, Newspapers, Reference Books.

    ERIC Educational Resources Information Center

    Madden, Peter

    The annotated entries in this bibliography of publications for children are divided into two categories: magazines and newspapers, and reference books. The first section, arranged alphabetically, includes periodicals on sports, science, history, hobbies, and entertainment. The reference books are grouped under the following headings: biography,…

  2. 47 CFR 15.11 - Cross reference.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 47 Telecommunication 1 2013-10-01 2013-10-01 false Cross reference. 15.11 Section 15.11 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL RADIO FREQUENCY DEVICES General § 15.11 Cross reference. The provisions of subparts A, H, I, J and K of part 2 apply to intentional and unintentional...

  3. 47 CFR 15.11 - Cross reference.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 47 Telecommunication 1 2014-10-01 2014-10-01 false Cross reference. 15.11 Section 15.11 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL RADIO FREQUENCY DEVICES General § 15.11 Cross reference. The provisions of subparts A, H, I, J and K of part 2 apply to intentional and unintentional...

  4. 47 CFR 15.11 - Cross reference.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 1 2012-10-01 2012-10-01 false Cross reference. 15.11 Section 15.11 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL RADIO FREQUENCY DEVICES General § 15.11 Cross reference. The provisions of subparts A, H, I, J and K of part 2 apply to intentional and unintentional...

  5. 47 CFR 15.11 - Cross reference.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 47 Telecommunication 1 2011-10-01 2011-10-01 false Cross reference. 15.11 Section 15.11 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL RADIO FREQUENCY DEVICES General § 15.11 Cross reference. The provisions of subparts A, H, I, J and K of part 2 apply to intentional and unintentional...

  6. 47 CFR 15.11 - Cross reference.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 47 Telecommunication 1 2010-10-01 2010-10-01 false Cross reference. 15.11 Section 15.11 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL RADIO FREQUENCY DEVICES General § 15.11 Cross reference. The provisions of subparts A, H, I, J and K of part 2 apply to intentional and unintentional...

  7. Statistical Sampling of Reference Desk Inquiries.

    ERIC Educational Resources Information Center

    Edinger, Joyce A.; Falk, Steven

    1981-01-01

    Discusses the application of statistical sampling to the compiling of reference-desk statistics, and describes a technique that uses the Pearson correlation procedure of SPSS (Statistical Package for the Social Sciences) to determine appropriate sampling periods for keeping reference desk statistics at the University of Missouri at St. Louis. (FM)

  8. SCORE, A Measurement of Reference Service.

    ERIC Educational Resources Information Center

    Beeler, Richard J.

    The University of Denver Libraries employed SCORE (Service Components Reliability and Efficiency), a cost analysis technique, to measure effectiveness and cost of reference activity. This report examines the results and the problems encountered in application of this methodology. A reference model, designed as a flow chart, was developed by…

  9. Writing references and using citation management software.

    PubMed

    Sungur, Mukadder Orhan; Seyhan, Tülay Özkan

    2013-09-01

    The correct citation of references is obligatory to gain scientific credibility, to honor the original ideas of previous authors and to avoid plagiarism. Currently, researchers can easily find, cite and store references using citation management software. In this review, two popular citation management software programs (EndNote and Mendeley) are summarized. PMID:26328132

  10. CD-ROM + Fax = Shared Reference Resources.

    ERIC Educational Resources Information Center

    Fitzwater, Diana; Fradkin, Bernard

    1988-01-01

    Describes the Reference by GammaFax Project, which joined nine area libraries to provide cooperative reference access to optical disk databases. The configuration of disk players, microcomputers, and facsimile equipment used by the libraries is explained, and the improvements in cost effectiveness, provision of service, and librarian expertise are…

  11. Advanced Food Science and Nutrition Reference Book.

    ERIC Educational Resources Information Center

    Texas Tech Univ., Lubbock. Home Economics Curriculum Center.

    Developed with input from personnel in the industries, this reference book complements the curriculum guide for a laboratory course on the significance of nutrition in food science. The reference book is organized into 25 chapters, each beginning with essential elements and objectives. Within the text, italicized, bold-faced vocabulary terms are…

  12. 49 CFR 171.7 - Reference material.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... Director of the Federal Register in accordance with 5 U.S.C 552(a) and 1 CFR part 51. Material is... information only and may not be all inclusive. Source and name of material 49 CFR reference Air Transport... sections in which the material is referenced. Source and name of material 49 CFR reference...

  13. Reference. Advisory List of Instructional Media.

    ERIC Educational Resources Information Center

    North Carolina State Dept. of Public Education, Raleigh.

    The reference books featured in this annotated bibliography were selected from those titles that publishers submitted to the North Carolina Department of Public Instruction for review. As such, it is not a comprehensive list of all reference titles in print. This guide organizes the 33 titles into major subject categories: (1) Arts…

  14. Spatial Reference Frame of Incidentally Learned Attention

    ERIC Educational Resources Information Center

    Jiang, Yuhong V.; Swallow, Khena M.

    2013-01-01

    Visual attention prioritizes information presented at particular spatial locations. These locations can be defined in reference frames centered on the environment or on the viewer. This study investigates whether incidentally learned attention uses a viewer-centered or environment-centered reference frame. Participants conducted visual search on a…

  15. On Vague Reference in College English

    ERIC Educational Resources Information Center

    Ma, Jianhe

    2011-01-01

    We often come across examples of vague reference in English learning, especially college English learning. On entering college, students tend to feel at a loss since their vocabulary is required to be enlarged rapidly and a variety of reference patterns are included in their learning materials which mostly come from American and European original…

  16. Uncertainty in Reference and Information Service

    ERIC Educational Resources Information Center

    VanScoy, Amy

    2015-01-01

    Introduction: Uncertainty is understood as an important component of the information seeking process, but it has not been explored as a component of reference and information service. Method: Interpretative phenomenological analysis was used to examine the practitioner perspective of reference and information service for eight academic research…

  17. 32 CFR 2700.1 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 6 2010-07-01 2010-07-01 false References. 2700.1 Section 2700.1 National Defense Other Regulations Relating to National Defense OFFICE FOR MICRONESIAN STATUS NEGOTIATIONS SECURITY INFORMATION REGULATIONS Introduction § 2700.1 References. (a) Executive Order 12065, “National...

  18. 33 CFR 274.3 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false References. 274.3 Section 274.3 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE PEST CONTROL PROGRAM FOR CIVIL WORKS PROJECTS Project Operation § 274.3 References. (a) Pub. L. 92-516,...

  19. 4 CFR 2.2 - References.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 4 Accounts 1 2010-01-01 2010-01-01 false References. 2.2 Section 2.2 Accounts GOVERNMENT ACCOUNTABILITY OFFICE PERSONNEL SYSTEM PURPOSE AND GENERAL PROVISION § 2.2 References. (a) Subchapters III and IV of Chapter 7 of Title 31 U.S.C. (b) Title 5, United States Code....

  20. 32 CFR 507.2 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 3 2010-07-01 2010-07-01 true References. 507.2 Section 507.2 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY AID OF CIVIL AUTHORITIES AND PUBLIC RELATIONS... QUALITY CONTROL PROGRAM Introduction § 507.2 References. Related publications are listed in paragraphs...

  1. 32 CFR 625.3 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 3 2010-07-01 2010-07-01 true References. 625.3 Section 625.3 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY SUPPLIES AND EQUIPMENT SURFACE TRANSPORTATION-ADMINISTRATIVE VEHICLE MANAGEMENT § 625.3 References. (a) Title 31, U.S. Code, section 638. (b)...

  2. 32 CFR 2103.1 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 6 2010-07-01 2010-07-01 false References. 2103.1 Section 2103.1 National Defense Other Regulations Relating to National Defense NATIONAL SECURITY COUNCIL REGULATIONS TO IMPLEMENT... § 2103.1 References. (a) Executive Order 12065, “National Security Information,” dated June 28, 1978....

  3. 32 CFR 634.2 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 4 2010-07-01 2010-07-01 true References. 634.2 Section 634.2 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) LAW ENFORCEMENT AND CRIMINAL INVESTIGATIONS MOTOR VEHICLE TRAFFIC SUPERVISION Introduction § 634.2 References. Required and...

  4. 36 CFR 328.3 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... ENGINEERS § 328.3 References. (a) Title 36 CFR, part 327, Rules and Regulations Governing Public Use of... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false References. 328.3 Section 328.3 Parks, Forests, and Public Property CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY REGULATION...

  5. 40 CFR 270.6 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 1 CFR part 51. These materials are incorporated as they exist on the date of approval and a notice... 40 Protection of Environment 26 2010-07-01 2010-07-01 false References. 270.6 Section 270.6... ADMINISTERED PERMIT PROGRAMS: THE HAZARDOUS WASTE PERMIT PROGRAM General Information § 270.6 References....

  6. 33 CFR 238.3 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false References. 238.3 Section 238.3 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE WATER RESOURCES POLICIES AND AUTHORITIES: FLOOD DAMAGE REDUCTION MEASURES IN URBAN AREAS § 238.3 References....

  7. 32 CFR 518.2 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 3 2010-07-01 2010-07-01 true References. 518.2 Section 518.2 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY AID OF CIVIL AUTHORITIES AND PUBLIC RELATIONS THE FREEDOM OF INFORMATION ACT PROGRAM General Provisions § 518.2 References. Required and...

  8. 33 CFR 279.3 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... (33 CFR part 290). ... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false References. 279.3 Section 279.3... USE: ESTABLISHMENT OF OBJECTIVES § 279.3 References. (a) Pub. L. 89-72, “Federal Water...

  9. 77 FR 16761 - Incorporation by Reference

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-03-22

    .... We published an announcement of the petition and a request for comments on February 27, 2012. 77 FR...; ] OFFICE OF THE FEDERAL REGISTER 1 CFR Part 51 Incorporation by Reference AGENCY: Office of the Federal... regulations governing the approval of agency requests to incorporate material by reference into the Code...

  10. 33 CFR 214.3 - Reference.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Reference. 214.3 Section 214.3 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE EMERGENCY SUPPLIES OF DRINKING WATER § 214.3 Reference. (a) Pub. L. 84-99, as amended (33 U.S.C. 701n). (b) Pub....

  11. 10 CFR 710.3 - Reference.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 4 2010-01-01 2010-01-01 false Reference. 710.3 Section 710.3 Energy DEPARTMENT OF ENERGY CRITERIA AND PROCEDURES FOR DETERMINING ELIGIBILITY FOR ACCESS TO CLASSIFIED MATTER OR SPECIAL NUCLEAR... Special Nuclear Material General Provisions § 710.3 Reference. The pertinent sections of the Atomic...

  12. 32 CFR 651.2 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 4 2010-07-01 2010-07-01 true References. 651.2 Section 651.2 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) ENVIRONMENTAL QUALITY ENVIRONMENTAL ANALYSIS OF ARMY ACTIONS (AR 200-2) Introduction § 651.2 References. Required and related publications...

  13. 33 CFR 236.3 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false References. 236.3 Section 236.3 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE WATER... QUALITY § 236.3 References. (a) PL 89-72 (b) ER 1105-2-10 (c) ER 1105-2-200...

  14. 32 CFR 552.142 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 3 2010-07-01 2010-07-01 true References. 552.142 Section 552.142 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY MILITARY RESERVATIONS AND NATIONAL... Fort Benjamin Harrison, Indiana § 552.142 References. Required and related publications are...

  15. 32 CFR 865.101 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 6 2010-07-01 2010-07-01 false References. 865.101 Section 865.101 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE ORGANIZATION AND MISSION-GENERAL PERSONNEL REVIEW BOARDS Air Force Discharge Review Board § 865.101 References. (a) Title 10 U.S.C.,...

  16. 24 CFR 35.1310 - References.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... by EPA under 40 CFR 745.324 to administer and enforce lead-based paint programs. ... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false References. 35.1310 Section 35.1310... Hazard Evaluation and Hazard Reduction Activities § 35.1310 References. Further guidance...

  17. 32 CFR 552.182 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 3 2010-07-01 2010-07-01 true References. 552.182 Section 552.182 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY MILITARY RESERVATIONS AND NATIONAL... Facilities § 552.182 References. Publications referenced in this section may be reviewed in the...

  18. 32 CFR 552.107 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 3 2010-07-01 2010-07-01 true References. 552.107 Section 552.107 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY MILITARY RESERVATIONS AND NATIONAL... References. (a) AR 190-5 (Motor Vehicle Traffic Supervision) (b) AR 190-52 (Countering Terrorism and...

  19. Anaphoric Reference in Creoles and Noncreoles.

    ERIC Educational Resources Information Center

    Escure, Genevieve

    1993-01-01

    Three categories of topic referents (nominal, pronominal, and periphrastic) are identified in 27 Belizean texts and 12 American texts, and the effects of referent choice of two variables (topic number and stylistic/lectal context) are investigated. One finding is that Belizean lects are strikingly similar to spontaneous styles of American English.…

  20. So You Want To Do Virtual Reference?

    ERIC Educational Resources Information Center

    Coffman, Steve

    2001-01-01

    Examines the practical details of setting up live online reference services in libraries. Topics include choosing software; differences between licensed and hosted applications; models used to implement virtual reference services; how libraries are using these services in day to day operations; and marketing strategies. (Author/LRW)

  1. Creating an Instant Messaging Reference System.

    ERIC Educational Resources Information Center

    Fagan, Jody Condit; Calloway, Michele

    2001-01-01

    Discussion of library digital reference services focuses on the features of instant messaging reference systems and the in-house development of a system that incorporates them at Southern Illinois University at Carbondale. Summarizes and evaluates library chat system features and compares commercial software that is available. (Author/LRW)

  2. Ready Reference Collections: Thoughts on Trends

    ERIC Educational Resources Information Center

    Fernandes, Maria Isabel

    2008-01-01

    What is a ready reference collection? A stack of reference books selected according to personal interests? Each institution is unique in its needs and so are the collections that each library carries. The curricula and programs determine the collection development policies and the student population justifies the needs for their implementation. Is…

  3. S. R. Ranganathan's Theory of Reference Service.

    ERIC Educational Resources Information Center

    Varghese, Manoj M.

    A study of S. R. Ranganathan's theory of reference service is undertaken by using an historical methodology. It was evident from the literature review that Ranganathan had established that reference service was the most important work and served as the hub of all library practices. There were six factors that were repeatedly considered by…

  4. Research in Library Reference/Information Service.

    ERIC Educational Resources Information Center

    Lynch, Mary Jo

    1983-01-01

    This review of library reference service research, which focuses on the provision of information in response to questions, covers measurement of reference service, evaluation using unobtrusive techniques, online search services, information needs and uses, the process of asking and answering questions, and artificial intelligence. Eighty-four…

  5. Using Quality Concepts to Improve Reference Services.

    ERIC Educational Resources Information Center

    Brown, Janet Dagenais

    1994-01-01

    Discusses how to improve library reference service, especially the effective delivery of accurate answers, based on a program at Wichita State University (Kansas) that used concepts of quality from business and organizational management. Topics addressed include customers and customer service, and methods of reference service evaluation. (Contains…

  6. Expanding Networks: Reference Services for MRDF.

    ERIC Educational Resources Information Center

    Jones, Ray; Seale, Colleen

    1988-01-01

    Discussion of issues concerned with providing library reference services to machine readable data files focuses on numeric databases. The team approach used at the University of Florida, which incorporates reference librarians, programers and data managers, database producers and vendors, and professional associations, is described. A bibliography…

  7. 32 CFR 1290.1 - References.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 32 National Defense 6 2013-07-01 2013-07-01 false References. 1290.1 Section 1290.1 National Defense Other Regulations Relating to National Defense DEFENSE LOGISTICS AGENCY MISCELLANEOUS PREPARING AND PROCESSING MINOR OFFENSES AND VIOLATION NOTICES REFERRED TO U.S. DISTRICT COURTS §...

  8. 32 CFR 1290.1 - References.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 32 National Defense 6 2011-07-01 2011-07-01 false References. 1290.1 Section 1290.1 National Defense Other Regulations Relating to National Defense DEFENSE LOGISTICS AGENCY MISCELLANEOUS PREPARING AND PROCESSING MINOR OFFENSES AND VIOLATION NOTICES REFERRED TO U.S. DISTRICT COURTS §...

  9. 21 CFR 660.3 - Reference panel.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... ADDITIONAL STANDARDS FOR DIAGNOSTIC SUBSTANCES FOR LABORATORY TESTS Antibody to Hepatitis B Surface Antigen § 660.3 Reference panel. A Reference Hepatitis B Surface Antigen Panel shall be obtained from the Center... shall be used for determining the potency and specificity of Antibody to Hepatitis B Surface Antigen....

  10. 21 CFR 660.3 - Reference panel.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... STANDARDS FOR DIAGNOSTIC SUBSTANCES FOR LABORATORY TESTS Antibody to Hepatitis B Surface Antigen § 660.3 Reference panel. A Reference Hepatitis B Surface Antigen Panel shall be obtained from the Center for... used for determining the potency and specificity of Antibody to Hepatitis B Surface Antigen....

  11. 49 CFR 171.7 - Reference material.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... Director of the Federal Register in accordance with 5 U.S.C 552(a) and 1 CFR part 51. Material is... information only and may not be all inclusive. Source and name of material 49 CFR reference Air Transport... sections in which the material is referenced. Source and name of material 49 CFR reference...

  12. 49 CFR 171.7 - Reference material.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... Director of the Federal Register in accordance with 5 U.S.C 552(a) and 1 CFR part 51. Material is... information only and may not be all inclusive. Source and name of material 49 CFR reference Air Transport... sections in which the material is referenced. Source and name of material 49 CFR reference...

  13. 40 CFR 260.11 - References.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 27 2013-07-01 2013-07-01 false References. 260.11 Section 260.11 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) HAZARDOUS WASTE MANAGEMENT SYSTEM: GENERAL Definitions § 260.11 References. (a) When used in parts 260 through 268 and 278 of this chapter, the...

  14. 40 CFR 260.11 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 25 2010-07-01 2010-07-01 false References. 260.11 Section 260.11 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) HAZARDOUS WASTE MANAGEMENT SYSTEM: GENERAL Definitions § 260.11 References. (a) When used in parts 260 through 268 and 278 of this chapter, the...

  15. Accuracy of References in Five Entomology Journals.

    ERIC Educational Resources Information Center

    Kristof, Cynthia

    ln this paper, the bibliographical references in five core entomology journals are examined for citation accuracy in order to determine if the error rates are similar. Every reference printed in each journal's first issue of 1992 was examined, and these were compared to the original (cited) publications, if possible, in order to determine the…

  16. 33 CFR 239.3 - References.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 33 Navigation and Navigable Waters 3 2011-07-01 2011-07-01 false References. 239.3 Section 239.3 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE WATER RESOURCES POLICIES AND AUTHORITIES: FEDERAL PARTICIPATION IN COVERED FLOOD CONTROL CHANNELS § 239.3 References. (a) Executive Order...

  17. 33 CFR 240.3 - Reference.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 33 Navigation and Navigable Waters 3 2011-07-01 2011-07-01 false Reference. 240.3 Section 240.3 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE GENERAL CREDIT FOR FLOOD CONTROL § 240.3 Reference. Section 104 of Pub. L....

  18. English Language Arts. Delaware Teachers' Desk Reference.

    ERIC Educational Resources Information Center

    Delaware State Dept. of Education, Dover.

    This document represents one section of the Delaware Teachers' Desk Reference to Standards and Performance Indicators for Curriculum Planning and Unit Development produced by the Delaware Department of Education. The Desk Reference is part of the Delaware Department of Education's ongoing efforts to provide assistance and support to local school…

  19. Integrative analysis of 111 reference human epigenomes

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The reference human genome sequence set the stage for studies of genetic variation and its association with human disease, but epigenomic studies lack a similar reference. To address this need, the NIH Roadmap Epigenomics Consortium generated the largest collection so far of human epigenomes for pri...

  20. Economics: A Guide to Reference Sources.

    ERIC Educational Resources Information Center

    Mason, Mary, Comp.

    Approximately 84 reference materials on economics located in the McLennan Library, McGill University (Montreal), are cited in this annotated bibliography. The bibliography serves to provide an overview of the printed bibliographic and reference sources useful for the study of economics. Financial and business sources and statistical compendia and…

  1. 44 CFR 59.4 - References.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 1954, as amended by the Housing and Community Development Act of 1974 (24 CFR 600.72). (12) Executive... INSURANCE AND HAZARD MITIGATION National Flood Insurance Program GENERAL PROVISIONS General § 59.4 References. (a) The following are statutory references for the National Flood Insurance Program, under...

  2. 44 CFR 59.4 - References.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 1954, as amended by the Housing and Community Development Act of 1974 (24 CFR 600.72). (12) Executive... INSURANCE AND HAZARD MITIGATION National Flood Insurance Program GENERAL PROVISIONS General § 59.4 References. (a) The following are statutory references for the National Flood Insurance Program, under...

  3. 44 CFR 59.4 - References.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 1954, as amended by the Housing and Community Development Act of 1974 (24 CFR 600.72). (12) Executive... INSURANCE AND HAZARD MITIGATION National Flood Insurance Program GENERAL PROVISIONS General § 59.4 References. (a) The following are statutory references for the National Flood Insurance Program, under...

  4. 44 CFR 59.4 - References.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 1954, as amended by the Housing and Community Development Act of 1974 (24 CFR 600.72). (12) Executive... INSURANCE AND HAZARD MITIGATION National Flood Insurance Program GENERAL PROVISIONS General § 59.4 References. (a) The following are statutory references for the National Flood Insurance Program, under...

  5. 33 CFR 240.3 - Reference.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Reference. 240.3 Section 240.3 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE GENERAL CREDIT FOR FLOOD CONTROL § 240.3 Reference. Section 104 of Pub. L. 99-662....

  6. Going Prime Time with Live Chat Reference.

    ERIC Educational Resources Information Center

    Hoag, Tara J.; Cichanowicz, Edana McCaffrey

    2001-01-01

    Describes the development of the Suffolk Cooperative Library System's live, online chat reference service, a pilot project for public libraries in Suffolk County (New York). Topics include chat software selection; a virtual reference collection; marketing; funding; staffing; evaluation; expanded hours of service; email; and extracting data from…

  7. 47 CFR 15.705 - Cross reference.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 47 Telecommunication 1 2010-10-01 2010-10-01 false Cross reference. 15.705 Section 15.705 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL RADIO FREQUENCY DEVICES Television Band Devices § 15.705 Cross reference. (a) The provisions of subparts A, B, and C of this part apply to TVBDs, except...

  8. 32 CFR 516.2 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 3 2010-07-01 2010-07-01 true References. 516.2 Section 516.2 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY AID OF CIVIL AUTHORITIES AND PUBLIC RELATIONS LITIGATION General § 516.2 References. Applicable publications and forms are listed in appendix A to...

  9. Archaeology: A Student's Guide to Reference Sources.

    ERIC Educational Resources Information Center

    Desautels, Almuth, Comp.

    This bibliography lists reference sources for research in archaeology. It is arranged in sections by type of reference source with subsections for general works and works covering specific areas. Categorized are handbooks; directories, biographies, and museums; encyclopedias; dictionaries; atlases; guides, manuals, and surveys; bibliographies; and…

  10. Health physics research reactor reference dosimetry

    SciTech Connect

    Sims, C.S.; Ragan, G.E.

    1987-06-01

    Reference neutron dosimetry is developed for the Health Physics Research Reactor (HPRR) in the new operational configuration directly above its storage pit. This operational change was physically made early in CY 1985. The new reference dosimetry considered in this document is referred to as the 1986 HPRR reference dosimetry and it replaces any and all HPRR reference documents or papers issued prior to 1986. Reference dosimetry is developed for the unshielded HPRR as well as for the reactor with each of five different shield types and configurations. The reference dosimetry is presented in terms of three different dose and six different dose equivalent reporting conventions. These reporting conventions cover most of those in current use by dosimetrists worldwide. In addition to the reference neutron dosimetry, this document contains other useful dosimetry-related data for the HPRR in its new configuration. These data include dose-distance measurements and calculations, gamma dose measurements, neutron-to-gamma ratios, ''9-to-3 inch'' ratios, threshold detector unit measurements, 56-group neutron energy spectra, sulfur fluence measurements, and details concerning HPRR shields. 26 refs., 11 figs., 31 tabs.

  11. Reach for Reference. Grolier's The Civil War

    ERIC Educational Resources Information Center

    Safford, Barbara Ripp

    2005-01-01

    This column describes Grolier's new ten-volume reference set, "The Civil War." The volumes are easy to handle and the set's appearance is designed to appeal to middle level students. Arrangement is alphabetical from Abolition in volume one to Zouaves in volume ten with reasonable cross references to other relevant articles. Each volume contains a…

  12. 47 CFR 15.405 - Cross reference.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 47 Telecommunication 1 2014-10-01 2014-10-01 false Cross reference. 15.405 Section 15.405 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL RADIO FREQUENCY DEVICES Unlicensed National Information Infrastructure Devices § 15.405 Cross reference. (a) The provisions of subparts A, B, and C of this part apply...

  13. 47 CFR 15.405 - Cross reference.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 1 2012-10-01 2012-10-01 false Cross reference. 15.405 Section 15.405 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL RADIO FREQUENCY DEVICES Unlicensed National Information Infrastructure Devices § 15.405 Cross reference. (a) The provisions of subparts A, B, and C of this part apply...

  14. 47 CFR 15.405 - Cross reference.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 47 Telecommunication 1 2013-10-01 2013-10-01 false Cross reference. 15.405 Section 15.405 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL RADIO FREQUENCY DEVICES Unlicensed National Information Infrastructure Devices § 15.405 Cross reference. (a) The provisions of subparts A, B, and C of this part apply...

  15. Stress-Burnout: A Bibliography. 1000+ References.

    ERIC Educational Resources Information Center

    Riggar, T. F.; Beardsley, M.

    This comprehensive bibliography contains an alphabetized list of over 1000 references dealing with job stress and burnout. All relevant published references are included; they represent major journals from a wide range of disciplines, including psychology, sociology, management and administration, and human services such as social work and…

  16. Gastronomic Reference, Synecdoche, and Political Images.

    ERIC Educational Resources Information Center

    Brummett, Barry

    1981-01-01

    Defines gastronomic reference, or mention of what public figures eat, as synecdoche. Illustrates how use of this rhetorical device contributed to public figures and public images in the 1980 presidential campaign. Argues that interest in gastronomic reference leads to a broader concern for how synecdoche functions in public discourse. (PD)

  17. Reference Services Planning in the 90s.

    ERIC Educational Resources Information Center

    Eckwright, Gail Z., Ed.; Keenan, Lori M., Ed.

    The focus of this collection of papers about library reference service is on the community outside the library, rather than the special populations served within it. "Conflicts in Value Systems" (Allen B. Veaner) is an overview of the major conflict areas facing the library profession today. "Reference Services for Off-Campus Students and Faculty"…

  18. 23 CFR 650.317 - Reference manuals.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ...(a) and 1 CFR part 51. These materials are incorporated as they exist on the date of the approval... 23 Highways 1 2010-04-01 2010-04-01 false Reference manuals. 650.317 Section 650.317 Highways..., STRUCTURES, AND HYDRAULICS National Bridge Inspection Standards § 650.317 Reference manuals. (a)...

  19. 32 CFR 1290.1 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 6 2010-07-01 2010-07-01 false References. 1290.1 Section 1290.1 National Defense Other Regulations Relating to National Defense DEFENSE LOGISTICS AGENCY MISCELLANEOUS PREPARING AND PROCESSING MINOR OFFENSES AND VIOLATION NOTICES REFERRED TO U.S. DISTRICT COURTS §...

  20. 43 CFR 1840.1 - Cross reference.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 43 Public Lands: Interior 2 2014-10-01 2014-10-01 false Cross reference. 1840.1 Section 1840.1 Public Lands: Interior Regulations Relating to Public Lands (Continued) BUREAU OF LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR GENERAL MANAGEMENT (1000) APPEALS PROCEDURES § 1840.1 Cross reference. For special procedural rules applicable to appeals...

  1. 43 CFR 1850.1 - Cross reference.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 43 Public Lands: Interior 2 2014-10-01 2014-10-01 false Cross reference. 1850.1 Section 1850.1 Public Lands: Interior Regulations Relating to Public Lands (Continued) BUREAU OF LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR GENERAL MANAGEMENT (1000) HEARINGS PROCEDURES Hearing Procedures; General § 1850.1 Cross reference. For special...

  2. Flexible Educational Facilities. An Annotated Reference List.

    ERIC Educational Resources Information Center

    Wakefield, Howard E.

    These references on flexible educational facilities are abstracted by the ERIC Clearinghouse on Educational Facilities. College material includes an experimental learning center, a college health center, a fine arts center, and university library design. References on schools include secondary school design, flexible high school design, standard…

  3. Reflections on Malpractice of Reference Librarians.

    ERIC Educational Resources Information Center

    Wan, Ronglin

    1994-01-01

    Explores the legal ramifications of malpractice among librarians and the possible impact on services due to fear of being sued. Topics include identification of potential malpractice areas; cooperative electronic reference services; use of reference standards; insurance; contract; disclaimer; updating library collections; using Internet resources;…

  4. Referent Salience Affects Second Language Article Use

    ERIC Educational Resources Information Center

    Trenkic, Danijela; Pongpairoj, Nattama

    2013-01-01

    The effect of referent salience on second language (L2) article production in real time was explored. Thai (-articles) and French (+articles) learners of English described dynamic events involving two referents, one visually cued to be more salient at the point of utterance formulation. Definiteness marking was made communicatively redundant with…

  5. Automation and Job Satisfaction among Reference Librarians.

    ERIC Educational Resources Information Center

    Whitlatch, Jo Bell

    1991-01-01

    Discussion of job satisfaction and the level of job performance focuses on the effect of automation on job satisfaction among reference librarians. The influence of stress is discussed, a job strain model is explained, and examples of how to design a job to reduce the stress caused by automation are given. (12 references) (LRW)

  6. THE ASCE STANDARDIZED REFERENCE EVAPOTRANSPIRATION EQUATION

    Technology Transfer Automated Retrieval System (TEKTRAN)

    This report describes the standardization of calculation of reference evapotranspiration (ET) as recommended by the Task Committee on Standardization of Reference Evapotranspiration of the Environmental and Water Resources Institute of the American Society of Civil Engineers. The purpose of the stan...

  7. Aspects of Reference in Figurative Language.

    ERIC Educational Resources Information Center

    Pankhurst, Anne

    1995-01-01

    This study considers some problems of reference found in figurative language, particularly in metaphor and metonymy. Analysis is based on the notion that the effects communicated by figurative language depend to a large extent on reference to more than one concept, experience, or entity, and that the presence of multiple potential referents…

  8. Reference in Library and Information Science Education.

    ERIC Educational Resources Information Center

    Chandler, Yvonne J.

    2001-01-01

    Graduate programs must examine the curriculum for reference and information access professionals. Greater access to information sources by users has highlighted the need for reference and information professionals to develop new skills including more technological knowledge, a better understanding of user information-seeking, new instructional…

  9. 47 CFR 15.405 - Cross reference.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 47 Telecommunication 1 2010-10-01 2010-10-01 false Cross reference. 15.405 Section 15.405 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL RADIO FREQUENCY DEVICES Unlicensed National Information Infrastructure Devices § 15.405 Cross reference. (a) The provisions of subparts A, B, and C of this part apply...

  10. 47 CFR 15.405 - Cross reference.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 47 Telecommunication 1 2011-10-01 2011-10-01 false Cross reference. 15.405 Section 15.405 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL RADIO FREQUENCY DEVICES Unlicensed National Information Infrastructure Devices § 15.405 Cross reference. (a) The provisions of subparts A, B, and C of this part apply...

  11. 21 CFR 660.3 - Reference panel.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... ADDITIONAL STANDARDS FOR DIAGNOSTIC SUBSTANCES FOR LABORATORY TESTS Antibody to Hepatitis B Surface Antigen § 660.3 Reference panel. A Reference Hepatitis B Surface Antigen Panel shall be obtained from the Center... shall be used for determining the potency and specificity of Antibody to Hepatitis B Surface Antigen....

  12. 21 CFR 660.3 - Reference panel.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... ADDITIONAL STANDARDS FOR DIAGNOSTIC SUBSTANCES FOR LABORATORY TESTS Antibody to Hepatitis B Surface Antigen § 660.3 Reference panel. A Reference Hepatitis B Surface Antigen Panel shall be obtained from the Center... shall be used for determining the potency and specificity of Antibody to Hepatitis B Surface Antigen....

  13. 21 CFR 660.3 - Reference panel.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... ADDITIONAL STANDARDS FOR DIAGNOSTIC SUBSTANCES FOR LABORATORY TESTS Antibody to Hepatitis B Surface Antigen § 660.3 Reference panel. A Reference Hepatitis B Surface Antigen Panel shall be obtained from the Center... shall be used for determining the potency and specificity of Antibody to Hepatitis B Surface Antigen....

  14. 40 CFR 92.5 - Reference materials.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ....C. 552(a) and 1 CFR part 51. To enforce any edition other than that specified in this section, a... 40 Protection of Environment 21 2012-07-01 2012-07-01 false Reference materials. 92.5 Section 92.5... Locomotives and Locomotive Engines § 92.5 Reference materials. The materials listed in this section...

  15. 40 CFR 92.5 - Reference materials.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be inspected...., Philadelphia, PA 19103. The table follows: Document number and name 40 CFR part 92 reference ASTM D 86-95... follows: Document number and name 40 CFR part 92 reference SAE Paper 770141, Optimization of a...

  16. 40 CFR 92.5 - Reference materials.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ....C. 552(a) and 1 CFR part 51. To enforce any edition other than that specified in this section, a... 40 Protection of Environment 20 2014-07-01 2013-07-01 true Reference materials. 92.5 Section 92.5... Locomotives and Locomotive Engines § 92.5 Reference materials. The materials listed in this section...

  17. 40 CFR 92.5 - Reference materials.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be inspected...., Philadelphia, PA 19103. The table follows: Document number and name 40 CFR part 92 reference ASTM D 86-95... follows: Document number and name 40 CFR part 92 reference SAE Paper 770141, Optimization of a...

  18. 40 CFR 92.5 - Reference materials.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ....C. 552(a) and 1 CFR part 51. To enforce any edition other than that specified in this section, a... 40 Protection of Environment 21 2013-07-01 2013-07-01 false Reference materials. 92.5 Section 92.5... Locomotives and Locomotive Engines § 92.5 Reference materials. The materials listed in this section...

  19. 40 CFR 91.6 - Reference materials.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 CFR part 91 reference SAE J1228/ISO 8665 November 1991 Small Craft-Marine Propulsion Engine and... incorporation by reference was approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be inspected at U.S. EPA, OAR, Air and Radiation Docket...

  20. 40 CFR 91.6 - Reference materials.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 CFR part 91 reference SAE J1228/ISO 8665 November 1991 Small Craft-Marine Propulsion Engine and... incorporation by reference was approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be inspected at U.S. EPA, OAR, Air and Radiation Docket...

  1. 40 CFR 91.6 - Reference materials.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 CFR part 91 reference SAE J1228/ISO 8665 November 1991 Small Craft-Marine Propulsion Engine and... incorporation by reference was approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be inspected at U.S. EPA, OAR, Air and Radiation Docket...

  2. 40 CFR 91.6 - Reference materials.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 CFR part 91 reference SAE J1228/ISO 8665 November 1991 Small Craft-Marine Propulsion Engine and... incorporation by reference was approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be inspected at U.S. EPA, OAR, Air and Radiation Docket...

  3. 40 CFR 91.6 - Reference materials.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 CFR part 91 reference SAE J1228/ISO 8665 November 1991 Small Craft-Marine Propulsion Engine and... incorporation by reference was approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be inspected at U.S. EPA, OAR, Air and Radiation Docket...

  4. MSDS sky reference and preamplifier study

    NASA Technical Reports Server (NTRS)

    Larsen, L.; Stewart, S.; Lambeck, P.

    1974-01-01

    The major goals in re-designing the Multispectral Scanner and Data System (MSDS) sky reference are: (1) to remove the sun-elevation angle and aircraft-attitude angle dependence from the solar-sky illumination measurement, and (2) to obtain data on the optical state of the atmosphere. The present sky reference is dependent on solar elevation and provides essentially no information on important atmospheric parameters. Two sky reference designs were tested. One system is built around a hyperbolic mirror and the reflection approach. A second approach to a sky reference utilizes a fish-eye lens to obtain a 180 deg field of view. A detailed re-design of the present sky reference around the fish-eye approach, even with its limitations, is recommended for the MSDS system. A preamplifier study was undertaken to find ways of improving the noise-equivalent reflectance by reducing the noise level for silicon detector channels on the MSDS.

  5. Adaptive Control with Reference Model Modification

    NASA Technical Reports Server (NTRS)

    Stepanyan, Vahram; Krishnakumar, Kalmanje

    2012-01-01

    This paper presents a modification of the conventional model reference adaptive control (MRAC) architecture in order to improve transient performance of the input and output signals of uncertain systems. A simple modification of the reference model is proposed by feeding back the tracking error signal. It is shown that the proposed approach guarantees tracking of the given reference command and the reference control signal (one that would be designed if the system were known) not only asymptotically but also in transient. Moreover, it prevents generation of high frequency oscillations, which are unavoidable in conventional MRAC systems for large adaptation rates. The provided design guideline makes it possible to track a reference commands of any magnitude from any initial position without re-tuning. The benefits of the method are demonstrated with a simulation example

  6. Physiology and its Importance for Reference Intervals

    PubMed Central

    Sikaris, Kenneth A

    2014-01-01

    Reference intervals are ideally defined on apparently healthy individuals and should be distinguished from clinical decision limits that are derived from known diseased patients. Knowledge of physiological changes is a prerequisite for understanding and developing reference intervals. Reference intervals may differ for various subpopulations because of differences in their physiology, most obviously between men and women, but also in childhood, pregnancy and the elderly. Changes in laboratory measurements may be due to various physiological factors starting at birth including weaning, the active toddler, immunological learning, puberty, pregnancy, menopause and ageing. The need to partition reference intervals is required when there are significant physiological changes that need to be recognised. It is important that laboratorians are aware of these changes otherwise reference intervals that attempt to cover a widened inter-individual variability may lose their usefulness. It is virtually impossible for any laboratory to directly develop reference intervals for each of the physiological changes that are currently known, however indirect techniques can be used to develop or validate reference intervals in some difficult situations such as those for children. Physiology describes our life’s journey, and it is only when we are familiar with that journey that we can appreciate a pathological departure. PMID:24659833

  7. What Determines the Response: Test or Reference?

    NASA Technical Reports Server (NTRS)

    Chukova, S. V.; Ahumada, A. J., Jr.; Null, Cynthia (Technical Monitor)

    1998-01-01

    The stability of sensory memory has been studied by presenting a reference stimulus, a delay, and a test stimulus. As has been pointed out by Lages and Treisman (1998 Vision Research 38 557-572), the usual measure of performance depends only on the effect of test variations on the responses. The Weber fraction characterizing performance is more properly called the test stimulus Weber fraction. We measure the relative contribution of the test and reference to the response by the ratio of the test Weber fraction to the reference Weber fraction. The stimuli were two dark lines on a bright background. Seven reference separations, varying from 9.5 to 16.7 arc min, were intermixed in each run. Interstimulus intervals (ISI) of 50, 200 and 2000 msec and intertrial intervals (ITI) of 500 and 2500 msec were investigated. When the ISI was short (50 or 200 msec), for both ITIs, responses were determined equally by the test and reference. For the long ISI (2000 msec), the reference stimulus contributed less. However, only for the 500 msec ITI (and not for all observers) was the contribution of the reference stimulus negligible, as Treisman's criterion setting theory might suggest.

  8. Rats exhibit reference-dependent choice behavior.

    PubMed

    Bhatti, Mehwish; Jang, Hyeran; Kralik, Jerald D; Jeong, Jaeseung

    2014-07-01

    Human preferences depend on whether a chosen outcome appears to be a loss or a gain compared with what had been expected, i.e., in comparison to a reference point. Because reference dependence has such a strong influence on human decision-making, it is important to uncover its origins, which will in turn help delineate the underlying mechanisms. It remains unknown whether rats use reference points in decision-making, and yet, the study of rats could help address the question of whether reference dependence is evolutionarily conserved among mammals and could provide a nonhuman animal model to investigate the neural mechanisms underlying this important cognitive process. The aim of the current study was to determine whether rats show reference-dependent choice behavior. We developed a novel paradigm by modifying the "T" maze by installing "pockets" to the left and right of the "T" stem that held reward pellets so rats would potentially develop reference values for each option prior to choice. We found that the rats were indeed sensitive to the way alternatives were presented. That is, they exhibited reference-dependent choice behavior by avoiding the choice option framed as a loss (e.g., having four reward pellets in the pocket, but receiving only one), at least under conditions with certain outcomes and clear differences between the reference and outcome quantities. Despite the small number of rats in this study, this species-level capacity suggests that reference dependence in general and loss aversion in particular may be conserved traits that evolved at or before the emergence of mammals. PMID:24657593

  9. Reference materials and reference measurement systems in laboratory medicine. Harmonization of nomenclature and definitions in reference measurement systems.

    PubMed

    Dybkaer, R

    1995-12-01

    Reliability of clinical laboratory results is obtained through quality assurance in both their production and transmission. The former involves a reference measurement system of reference materials and reference measurement procedures with metrological and statistical verification of results. The latter requires that sender and receiver have access to a common terminology. Thus, two data banks are required. A plurilingual systematic vocabulary related to the reference measurement system, giving concepts with terms and definitions concerning measurement standards, reference measurement procedures, internal quality control, external quality assessment, probability and statistics-mainly based on existing authoritative publications. The material should be processed by standard scientific terminological procedure and offered to pertinent organizations and specialists for comment before finalization and authorization. A multilingual collection of systematic names for properties examined by the branches of Laboratory Medicine, such as clinical chemistry, clinical immunology, clinical microbiology, clinical pharmacology, haematology and blood banking, and histochemistry and cytology. The database should function as a reference to consultation and as a link in the transmission of data between local laboratory "dialects". This should be based on the ongoing comprehensive IUPAC/IFCC project for forming names in collaboration with relevant scientific organisations and area specialists. The relational data base including "run-time" software would be accessed by e-mail (gopher or other storage medium). PMID:8845435

  10. Reference Librarians at the Reference Desk in a Learning Commons: A Mixed Methods Evaluation

    ERIC Educational Resources Information Center

    Fitzpatrick, Elizabeth B.; Moore, Anne C.; Lang, Beth W.

    2008-01-01

    At the University of Massachusetts Amherst's W.E.B. Du Bois Library's Learning Commons, only reference librarians staff the Reference and Research Assistance Desk. Surveys, a focus group, reference question transcriptions, and question-type tallies indicate that this service model is strongly preferred by users and librarians over the previous…

  11. Reference Books in Special Media. Reference Circular No. 82-4.

    ERIC Educational Resources Information Center

    Library of Congress, Washington, DC. National Library Service for the Blind and Physically Handicapped.

    Based on information contained in producers' catalogs and on responses to a survey conducted by the Reference Section of the Library of Congress National Library Service (NLS) for the Blind and Physically Handicapped, this publication lists reference materials produced in braille or in large type, and sound recordings of reference works available…

  12. A new thoron atmosphere reference measurement system.

    PubMed

    Sabot, B; Pierre, S; Michielsen, N; Bondiguel, S; Cassette, P

    2016-03-01

    A new thoron reference ((220)Rn) in air measurement system is developed at the LNE-LNHB with the collaboration of the IRSN. This measurement system is based on a reference volume with an alpha detector which is able to directly measure thoron and its decay products at atmospheric pressure. In order to improve the spectrum quality of the thoron progenies, we have applied an electric field to catch the decay products on the detector surface. The developed system is a portative device which can be used to measure reference thoron atmosphere such as the BACCARA chamber at IRSN (Picolo et al., 1999). As this system also allows the measurement of radon ((222)Rn) in air, it was validated using the radon primary standards made at the LNE-LNHB. This thoron measurement system will be used, at IRSN, as a reference instrument in order to calibrate the thoron activity concentration in the BACCARA facility. PMID:26701661

  13. A reference architecture for the component factory

    NASA Technical Reports Server (NTRS)

    Basili, Victor R.; Caldiera, Gianluigi; Cantone, Giovanni

    1992-01-01

    Software reuse can be achieved through an organization that focuses on utilization of life cycle products from previous developments. The component factory is both an example of the more general concepts of experience and domain factory and an organizational unit worth being considered independently. The critical features of such an organization are flexibility and continuous improvement. In order to achieve these features we can represent the architecture of the factory at different levels of abstraction and define a reference architecture from which specific architectures can be derived by instantiation. A reference architecture is an implementation and organization independent representation of the component factory and its environment. The paper outlines this reference architecture, discusses the instantiation process, and presents some examples of specific architectures by comparing them in the framework of the reference model.

  14. 40 CFR 1065.1010 - Reference materials.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Federal Register approved the incorporation by reference as prescribed in 5 U.S.C. 552(a) and 1 CFR part... Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels 1065.701 ASTM D6985-04a,...

  15. Improved reference models for middle atmosphere ozone

    NASA Technical Reports Server (NTRS)

    Keating, G. M.; Pitts, M. C.; Chen, C.

    1990-01-01

    This paper describes the improvements introduced into the original version of ozone reference model of Keating and Young (1985, 1987) which is to be incorporated in the next COSPAR International Reference Atmosphere (CIRA). The ozone reference model will provide information on the global ozone distribution (including the ozone vertical structure as a function of month and latitude from 25 to 90 km) combining data from five recent satellite experiments: the Nimbus 7 LIMS, Nimbus 7 SBUV, AE-2 Stratospheric Aerosol Gas Experiment (SAGE), Solar Mesosphere Explorer (SME) UV Spectrometer, and SME 1.27 Micron Airglow. The improved version of the reference model uses reprocessed AE-2 SAGE data (sunset) and extends the use of SAGE data from 1981 to the 1981-1983 time period. Comparisons are presented between the results of this ozone model and various nonsatellite measurements at different levels in the middle atmosphere.

  16. Improved reference models for middle atmosphere ozone

    NASA Technical Reports Server (NTRS)

    Keating, G. M.; Pitts, M. C.; Chen, C.

    1989-01-01

    Improvements are provided for the ozone reference model which is to be incorporated in the COSPAR International Reference Atmosphere (CIRA). The ozone reference model will provide considerable information on the global ozone distribution, including ozone vertical structure as a function of month and latitude from approximately 25 to 90 km, combining data from five recent satellite experiments (Nimbus 7 LIMS, Nimbus 7 SBUV, AE-2 SAGE, Solar Mesosphere Explorer (SME) UVS, and SME IR). The improved models are described and use reprocessed AE-2 SAGE data (sunset) and extend the use of SAGE data from 1981 to the period 1981-1983. Comparisons are shown between the ozone reference model and various nonsatellite measurements at different levels in the middle atmosphere.

  17. Changing technologies in the reference laboratory.

    PubMed

    O'Sullivan, M B

    1987-07-01

    Changes in technology will have a profound impact on specialized reference laboratories. In their research and development efforts, reference laboratories will have to pursue the incorporation of the technologies of molecular and cell biology into clinical practice. Computers can be applied to the management of clinical laboratory data bases and to the organization of scientific and clinical knowledge for medical consultation. Because of the distance between the site of acquisition of referred specimens and the laboratory, research on analyte stability is needed. Computer networking will help to solve problems of inadequacy of clinical information, and bar code technology will address the problems of specimen identification. Finally, improved telecommunication will permit reference laboratories of the future to be true medical consultation centers rather than just technical analysis operations. PMID:3606343

  18. Scientists, Information Seeking, and Reference Services.

    ERIC Educational Resources Information Center

    Von Seggern, Marilyn

    1995-01-01

    Discusses implications for restructuring library reference services suggested by information needs and information-seeking behavior of scientists. Highlights include scientific and informal communication, accessibility and creativity, and a holistic approach to user-centered services. (AEF)

  19. Reference Device-Assisted Adaptive Location Fingerprinting

    PubMed Central

    Wu, Dongjin; Xia, Linyuan

    2016-01-01

    Location fingerprinting suffers in dynamic environments and needs recalibration from time to time to maintain system performance. This paper proposes an adaptive approach for location fingerprinting. Based on real-time received signal strength indicator (RSSI) samples measured by a group of reference devices, the approach applies a modified Universal Kriging (UK) interpolant to estimate adaptive temporal and environmental radio maps. The modified UK can take the spatial distribution characteristics of RSSI into account. In addition, the issue of device heterogeneity caused by multiple reference devices is further addressed. To compensate the measuring differences of heterogeneous reference devices, differential RSSI metric is employed. Extensive experiments were conducted in an indoor field and the results demonstrate that the proposed approach not only adapts to dynamic environments and the situation of changing APs’ positions, but it is also robust toward measuring differences of heterogeneous reference devices. PMID:27258284

  20. Toward a generalized plate motion reference frame

    NASA Astrophysics Data System (ADS)

    Becker, T. W.; Schaeffer, A. J.; Lebedev, S.; Conrad, C. P.

    2015-05-01

    An absolute plate motion (APM) model is required to address issues such as the thermochemical evolution of Earth's mantle. All APM models have to rely on indirect inferences, including those based on hot spots and seismic anisotropy, each with their own set of uncertainties. Here, we explore a seafloor spreading-aligned reference frame. We show that this reference frame fits azimuthal seismic anisotropy in the uppermost mantle very well. The corresponding Euler pole is close to those of hot spot reference frames, ridge motion minimizing models, and geodynamic estimates of net rotation and predicts clear trench motion patterns. We conclude that a net rotation pole guided by the spreading-aligned model (at 64°E, 61°S, with moderate rotation of ˜ 0.2 … 0.3°/Myr) could indeed represent a standard, comprehensive reference frame for present-day plate motions with respect to the deep mantle.

  1. Astronomical catalog desk reference, 1994 edition

    NASA Technical Reports Server (NTRS)

    1994-01-01

    The Astronomical Catalog Desk Reference is designed to aid astronomers in locating machine readable catalogs in the Astronomical Data Center (ADC) archives. The key reference components of this document are as follows: A listing of shortened titles for all catalogs available from the ADC (includes the name of the lead author and year of publication), brief descriptions of over 300 astronomical catalogs, an index of ADC catalog numbers by subject keyword, and an index of ADC catalog numbers by author. The heart of this document is the set of brief descriptions generated by the ADC staff. The 1994 edition of the Astronomical Catalog Desk Reference contains descriptions for over one third of the catalogs in the ADC archives. Readers are encouraged to refer to this section for concise summaries of those catalogs and their contents.

  2. Simple method for model reference adaptive control

    NASA Technical Reports Server (NTRS)

    Seraji, H.

    1989-01-01

    A simple method is presented for combined signal synthesis and parameter adaptation within the framework of model reference adaptive control theory. The results are obtained using a simple derivation based on an improved Liapunov function.

  3. Method For Model-Reference Adaptive Control

    NASA Technical Reports Server (NTRS)

    Seraji, Homayoun

    1990-01-01

    Relatively simple method of model-reference adaptive control (MRAC) developed from two prior classes of MRAC techniques: signal-synthesis method and parameter-adaption method. Incorporated into unified theory, which yields more general adaptation scheme.

  4. USDA NATIONAL NUTRIENT DATABASE FOR STANDARD REFERENCE

    EPA Science Inventory

    The USDA Nutrient Database for Standard Reference (SR) is the major source of food composition data in the United States. It provides the foundation for most food composition databases in the public and private sectors.

  5. Selected Reference Books of 1979-80.

    ERIC Educational Resources Information Center

    Sheehy, Eugene P.

    1981-01-01

    Presents book reviews of recently published scholarly and general works of interest to reference workers in university libraries. The listing includes a brief roundup of new editions of standard works, continuations, and supplements. (RAA)

  6. Selected Reference Books of 1998-99.

    ERIC Educational Resources Information Center

    McIlvaine, Eileen

    1999-01-01

    Presents an annotated bibliography of selected reference books published between 1998 and 1999 under subject headings for biography, journalism, mythology, languages and literature, architecture and city planning, political science, economics, history, and new editions and supplements. (LRW)

  7. 40 CFR 1065.1010 - Reference materials.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Federal Register approved the incorporation by reference as prescribed in 5 U.S.C. 552(a) and 1 CFR part... of the International System of Units (SI), Barry N. Taylor, Physics Laboratory 1065.20,...

  8. SUPPORT FOR REFERENCE AND EQUIVALENCY PROGRAM

    EPA Science Inventory

    Federal Reference Methods (FRMs) and Federal Equivalent Methods (FEMs) form the backbone of the EPA's national monitoring strategy. They are the measurement methodologies that define attainment of a National Ambient Air Quality Standard (NAAQS). As knowledge and technology adva...

  9. Electronic Reference Services: Some Suggested Guidelines.

    ERIC Educational Resources Information Center

    Sloan, Bernie

    1998-01-01

    Suggests guidelines to help libraries formalize their electronic reference services. Covers the following issues: administration/management (library division/department, library administration, campus administration, academic departments); services; primary clientele; personnel; infrastructure/facilities; finances; and evaluation. (AEF)

  10. Reference Materials: Significance, General Requirements, and Demand.

    PubMed

    Kiełbasa, Anna; Gadzała-Kopciuch, Renata; Buszewski, Bogusław

    2016-05-01

    Reference materials play an important part in the quality control of measurements. Rapid development of such new scientific disciplines as proteomics, metabolomics, and genomics also necessitates development of new reference materials. This is a great challenge due to the complexity of the production of new reference materials and difficulties associated with achieving their homogeneity and stability. CRMs of tissue are of particular importance. They can be counted among the matrices that are most complex and time consuming in preparation. Tissue is the place of transformation and accumulation of many substances (e.g., metabolites, which are intermediate or end products resulting from metabolic processes). Trace amounts of many substances in tissues must be determined with adequate precision and accuracy. To meet the needs stemming from research and from problems and challenges faced by chemists, analysts, and toxicologists, the number of certified reference materials should be continuously increased. PMID:26042643

  11. Selected Reference Books of 2000/2001.

    ERIC Educational Resources Information Center

    McIlvaine, Eileen

    2002-01-01

    Presents an annotated list of selected recent scholarly and general reference works under the subject categories of archives; literature; music; psychology; sociology; black studies; women's studies; history and area studies; and new editions and supplements. (LRW)

  12. 23 CFR 650.317 - Reference manuals.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ...(a) and 1 CFR part 51. These materials are incorporated as they exist on the date of the approval..., STRUCTURES, AND HYDRAULICS National Bridge Inspection Standards § 650.317 Reference manuals. (a)...

  13. 23 CFR 650.317 - Reference manuals.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ...(a) and 1 CFR part 51. These materials are incorporated as they exist on the date of the approval..., STRUCTURES, AND HYDRAULICS National Bridge Inspection Standards § 650.317 Reference manuals. (a)...

  14. 23 CFR 650.317 - Reference manuals.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ...(a) and 1 CFR part 51. These materials are incorporated as they exist on the date of the approval..., STRUCTURES, AND HYDRAULICS National Bridge Inspection Standards § 650.317 Reference manuals. (a)...

  15. 23 CFR 650.317 - Reference manuals.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ...(a) and 1 CFR part 51. These materials are incorporated as they exist on the date of the approval..., STRUCTURES, AND HYDRAULICS National Bridge Inspection Standards § 650.317 Reference manuals. (a)...

  16. Genetics Home Reference: Axenfeld-Rieger syndrome

    MedlinePlus

    ... Cohen JS, Greff LJ, Wiggs JL. A second locus for Rieger syndrome maps to chromosome 13q14. Am J Hum Genet. 1996 Sep;59(3):613-9. ... Genetics Home Reference Site Map Contact Us Selection Criteria ...

  17. 40 CFR 1508.24 - Referring agency.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 33 2011-07-01 2011-07-01 false Referring agency. 1508.24 Section 1508.24 Protection of Environment COUNCIL ON ENVIRONMENTAL QUALITY TERMINOLOGY AND INDEX § 1508.24... or environmental quality....

  18. 40 CFR 1508.24 - Referring agency.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 34 2012-07-01 2012-07-01 false Referring agency. 1508.24 Section 1508.24 Protection of Environment COUNCIL ON ENVIRONMENTAL QUALITY TERMINOLOGY AND INDEX § 1508.24... or environmental quality....

  19. 40 CFR 1508.24 - Referring agency.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 34 2013-07-01 2013-07-01 false Referring agency. 1508.24 Section 1508.24 Protection of Environment COUNCIL ON ENVIRONMENTAL QUALITY TERMINOLOGY AND INDEX § 1508.24... or environmental quality....

  20. 40 CFR 1508.24 - Referring agency.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Referring agency. 1508.24 Section 1508.24 Protection of Environment COUNCIL ON ENVIRONMENTAL QUALITY TERMINOLOGY AND INDEX § 1508.24... or environmental quality....

  1. On Fractional Model Reference Adaptive Control

    PubMed Central

    Shi, Bao; Dong, Chao

    2014-01-01

    This paper extends the conventional Model Reference Adaptive Control systems to fractional ones based on the theory of fractional calculus. A control law and an incommensurate fractional adaptation law are designed for the fractional plant and the fractional reference model. The stability and tracking convergence are analyzed using the frequency distributed fractional integrator model and Lyapunov theory. Moreover, numerical simulations of both linear and nonlinear systems are performed to exhibit the viability and effectiveness of the proposed methodology. PMID:24574897

  2. 40 CFR 89.6 - Reference materials.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be inspected at US EPA, OAR, 1200 Pennsylvania Ave... 19428-2959. Document number and name 40 CFR part 89 reference ASTM D86-97: “Standard Test Method for... Commonwealth Dr., Warrendale, PA 15096-0001. Document number and name 40 CFR part 89 reference SAE J244 June...

  3. 40 CFR 89.6 - Reference materials.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be inspected at US EPA, OAR, 1200 Pennsylvania Ave... 19428-2959. Document number and name 40 CFR part 89 reference ASTM D86-97: “Standard Test Method for... Commonwealth Dr., Warrendale, PA 15096-0001. Document number and name 40 CFR part 89 reference SAE J244 June...

  4. Reference architecture for space data systems

    NASA Technical Reports Server (NTRS)

    Shames, P.; Yamada, T.

    2003-01-01

    This paper introduces the Reference Architecture for Space Data Systems (RASDS)that is being developed by CCSDS. RASDS uses five views to describe architectures of space data systems. These views are derived from the viewpoints of the Reference Model of Open Distributed Processing (RM-ODP), but they are slightly modified from the RM-ODP viewpoints so that they can better represent the concerns of space data systems.

  5. 36 CFR 330.3 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...) Section 120 of the Water Resource Development Act of 1976 (Pub. L. 94-587, 90 Stat. 2917). (d) 36 CFR... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false References. 330.3 Section 330... § 330.3 References. (a) Section 4 of the Flood Control Act of 1944, as amended (16 U.S.C. 460d)....

  6. 32 CFR 555.3 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 3 2010-07-01 2010-07-01 true References. 555.3 Section 555.3 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY MILITARY RESERVATIONS AND NATIONAL CEMETERIES CORPS... OTHERS § 555.3 References. (a) AR 10-5. (b) AR 37-27. (c) AR 70-1. (d) ER 1-1-6. (e) ER 1-1-7. (f) ER...

  7. Recommended reference figures for geophysics and geodesy

    NASA Technical Reports Server (NTRS)

    Khan, M. A.; Okeefe, J. A.

    1973-01-01

    Specific reference figures are recommended for consistent use in geophysics and geodesy. The selection of appropriate reference figure for geophysical studies suggests a relationship between the Antarctic negative gravity anomaly and the great shrinkage of the Antarctic ice cap about 4-5 million years ago. The depression of the south polar regions relative to the north polar regions makes the Southern Hemisphere flatter than the Northern Hemisphere, thus producing the third harmonic (pear-shaped) contribution to the earth's figure.

  8. On fractional Model Reference Adaptive Control.

    PubMed

    Shi, Bao; Yuan, Jian; Dong, Chao

    2014-01-01

    This paper extends the conventional Model Reference Adaptive Control systems to fractional ones based on the theory of fractional calculus. A control law and an incommensurate fractional adaptation law are designed for the fractional plant and the fractional reference model. The stability and tracking convergence are analyzed using the frequency distributed fractional integrator model and Lyapunov theory. Moreover, numerical simulations of both linear and nonlinear systems are performed to exhibit the viability and effectiveness of the proposed methodology. PMID:24574897

  9. 40 CFR 94.5 - Reference materials.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...: Table 2 of § 94.5—ISO Materials Document No. and name 40 CFR part 94 reference ISO 8178-1, Reciprocating internal combustion engines—Exhaust emission measurement—Part 1: Test-bed measurement of gaseous and... reference as prescribed in 5 U.S.C. 552(a) and 1 CFR part 51. Anyone may inspect copies at the U.S. EPA,...

  10. 40 CFR 94.5 - Reference materials.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ...: Table 2 of § 94.5—ISO Materials Document No. and name 40 CFR part 94 reference ISO 8178-1, Reciprocating internal combustion engines—Exhaust emission measurement—Part 1: Test-bed measurement of gaseous and... reference as prescribed in 5 U.S.C. 552(a) and 1 CFR part 51. Anyone may inspect copies at the U.S. EPA,...

  11. 16 CFR 1207.11 - References.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 16 Commercial Practices 2 2014-01-01 2014-01-01 false References. 1207.11 Section 1207.11 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION CONSUMER PRODUCT SAFETY ACT REGULATIONS SAFETY STANDARD FOR SWIMMING POOL SLIDES § 1207.11 References. (a) “Statistical Abstract of the United States 1973,” U.S. Dept. of Commerce, pp. 181-185, 192....

  12. Building complex reference objects from dual sets

    PubMed Central

    Patson, Nikole D.; Warren, Tessa

    2011-01-01

    There has been considerable psycholinguistic investigation into the conditions that allow separately introduced individuals to be joined into a plural set and represented as a complex reference object (e.g., Eschenbach, et al., 1989; Garrod & Sanford, 1982; Koh & Clifton, 2002; Koh et al., 2008; Moxey et al., 2004; Sanford & Lockhart, 1990). The current paper reports three eye-tracking experiments that investigate the less-well understood question of what conditions allow pointers to be assigned to the individuals within a previously undifferentiated set, turning it into a complex reference object. The experiments made use of a methodology used in Patson and Ferreira (2009) to distinguish between complex reference objects and undifferentiated sets. Experiments 1 and 2 demonstrated that assigning different properties to the members of an undifferentiated dual set via a conjoined modifier or a comparative modifier transformed it into a complex reference object. Experiment 3 indicated that assigning a property to only one member of an undifferentiated dual set introduced pointers to both members. These results demonstrate that pointers can be established to referents within a plural set without picking them out via anaphors; they set boundaries on the kinds of implicit contrasts between referents that establish pointers; and they illustrate that extremely subtle properties of the semantic and referential context can affect early parsing decisions. PMID:21666836

  13. The International Reference Preparation of Gramicidin*

    PubMed Central

    Lightbown, J. W.; Bond, Jillian M.; Woodward, Patricia M.

    1967-01-01

    The National Institute for Medical Research, London, was requested by the WHO Expert Committee on Biological Standardization to establish an International Reference Preparation of Gramicidin. This preparation was needed to standardize preparations of gramicidin containing predominantly gramicidin A, B and C, for which purpose the International Reference Preparation of Gramicidin S cannot be used. A batch of 100 g of crystalline gramicidin obtained in 1963 was distributed into ampoules in 55 mg amounts and dried in vacuo; the ampoules were then filled with dried nitrogen and sealed. The proposed international reference preparation was assayed biologically against the Master Standard of Gramicidin of the US Food and Drug Administration in 7 laboratories in 6 countries by turbidimetric methods. Significant curvature of the dose—response lines was found for most assays; no single transformation improved the linearity of assays from all laboratories. Although significant heterogeneity of potencies was obtained in 5 laboratories the mean potency ratios for all laboratories only varied over a range of 5% to 6%. The composition of the material is 7% gramicidin B, 50% gramicidin A and 25% gramicidin C; preparations of gramicidin containing appreciably higher concentrations of gramicidin B can be expected to give invalid assays against the international reference preparation. The material has been established as the International Reference Preparation of Gramicidin with a defined potency of 1000 IU/mg. The International Unit of Gramicidin is defined as the activity of 0.001 mg of the International Reference Preparation of Gramicidin. PMID:5299675

  14. Analysis of SOFCs Using Reference Electrodes

    SciTech Connect

    Finklea, H.; Chen, X.; Gerdes, K.; Pakalapati, S.; Celik, I.

    2013-01-01

    Reference electrodes are frequently applied to isolate the performance of one electrode in a solid oxide fuel cell. However, reference electrode simulations raise doubt to veracity of data collected using reference electrodes. The simulations predict that the reported performance for the one electrode will frequently contain performance of both electrodes. Nonetheless, recent reports persistently treat data so collected as ideally isolated. This work confirms the predictions of the reference electrode simulations on two SOFC designs, and to provides a method of validating the data measured in the 3-electrode configuration. Validation is based on the assumption that a change in gas composition to one electrode does not affect the impedance of the other electrode at open circuit voltage. This assumption is supported by a full physics simulation of the SOFC. Three configurations of reference electrode and cell design are experimentally examined using various gas flows and two temperatures. Impedance data are subjected to deconvolution analysis and equivalent circuit fitting and approximate polarization resistances of the cathode and anode are determined. The results demonstrate that the utility of reference electrodes is limited and often wholly inappropriate. Reported impedances and single electrode polarization values must be scrutinized on this basis.

  15. PEPR: pipelines for evaluating prokaryotic references.

    PubMed

    Olson, Nathan D; Zook, Justin M; Samarov, Daniel V; Jackson, Scott A; Salit, Marc L

    2016-04-01

    The rapid adoption of microbial whole genome sequencing in public health, clinical testing, and forensic laboratories requires the use of validated measurement processes. Well-characterized, homogeneous, and stable microbial genomic reference materials can be used to evaluate measurement processes, improving confidence in microbial whole genome sequencing results. We have developed a reproducible and transparent bioinformatics tool, PEPR, Pipelines for Evaluating Prokaryotic References, for characterizing the reference genome of prokaryotic genomic materials. PEPR evaluates the quality, purity, and homogeneity of the reference material genome, and purity of the genomic material. The quality of the genome is evaluated using high coverage paired-end sequence data; coverage, paired-end read size and direction, as well as soft-clipping rates, are used to identify mis-assemblies. The homogeneity and purity of the material relative to the reference genome are characterized by comparing base calls from replicate datasets generated using multiple sequencing technologies. Genomic purity of the material is assessed by checking for DNA contaminants. We demonstrate the tool and its output using sequencing data while developing a Staphylococcus aureus candidate genomic reference material. PEPR is open source and available at https://github.com/usnistgov/pepr . PMID:26935931

  16. Global daily reference evapotranspiration modeling and evaluation

    USGS Publications Warehouse

    Senay, G.B.; Verdin, J.P.; Lietzow, R.; Melesse, Assefa M.

    2008-01-01

    Accurate and reliable evapotranspiration (ET) datasets are crucial in regional water and energy balance studies. Due to the complex instrumentation requirements, actual ET values are generally estimated from reference ET values by adjustment factors using coefficients for water stress and vegetation conditions, commonly referred to as crop coefficients. Until recently, the modeling of reference ET has been solely based on important weather variables collected from weather stations that are generally located in selected agro-climatic locations. Since 2001, the National Oceanic and Atmospheric Administration's Global Data Assimilation System (GDAS) has been producing six-hourly climate parameter datasets that are used to calculate daily reference ET for the whole globe at 1-degree spatial resolution. The U.S. Geological Survey Center for Earth Resources Observation and Science has been producing daily reference ET (ETo) since 2001, and it has been used on a variety of operational hydrological models for drought and streamflow monitoring all over the world. With the increasing availability of local station-based reference ET estimates, we evaluated the GDAS-based reference ET estimates using data from the California Irrigation Management Information System (CIMIS). Daily CIMIS reference ET estimates from 85 stations were compared with GDAS-based reference ET at different spatial and temporal scales using five-year daily data from 2002 through 2006. Despite the large difference in spatial scale (point vs. ???100 km grid cell) between the two datasets, the correlations between station-based ET and GDAS-ET were very high, exceeding 0.97 on a daily basis to more than 0.99 on time scales of more than 10 days. Both the temporal and spatial correspondences in trend/pattern and magnitudes between the two datasets were satisfactory, suggesting the reliability of using GDAS parameter-based reference ET for regional water and energy balance studies in many parts of the world

  17. Myths of Isotopic Reference Materials Busted

    NASA Astrophysics Data System (ADS)

    Coplen, T.

    2007-12-01

    During the past several years, the determination of the isotopic abundances of elements including H, Li, B, C, N, O, Mg, Si, S, Cl, Ca, Cr, Fe, Cu, Zn, Tl, and Se has substantially increased because of expanded use in hydrology, environmental studies, microbiology, forensic investigations, atmospheric investigations, oceanography, etc. Improvements in instrumentation enable increasingly precise isotope-amount-ratio measurements in these fields, but these improvements in precision commonly do not lead to improvements in accuracy because of the lack or improper use of isotopic reference materials. When properly used, these critically important materials enable any laboratory worldwide to measure the same homogeneous sample and report the same isotopic abundance within analytical uncertainty. For example, for stable isotopic analysis of gaseous hydrogen samples, the agreement among 36 laboratories worldwide before normalization to any hydrogen gas reference material was 11.8 per mill. After normalization to anchors (gaseous H isotopic reference materials) at each end of the delta H-2 scale, the agreement was 0.85 per mill, an improvement of more than an order of magnitude. Consistency of delta C-13 measurements often can be improved by nearly 50 percent by anchoring the delta C-13 scale with two isotopic reference materials differing substantially in C-13 mole fraction, namely NBS 19 calcite and L-SVEC lithium carbonate. Agreement of delta C-13 values of four expert laboratories analyzing USGS40 L- glutamic acid by CF-IRMS methods improved from 0.084 to 0.015 per mill with use of the two scale anchors (NBS 19 and L-SVEC). Solid oxygen isotopic reference materials (IAEA-600 caffeine, IAEA-601 and IAEA-602 benzoic acids, IAEA-NO-3, USGS32, USGS34, and USGS35 nitrates, NBS-127, IAEA-SO-5, and IAEA-SO-6 barium sulfates) are poorly calibrated. Calibrating these solids to the VSMOW-SLAP reference water scale has been very difficult because both the solids and reference

  18. [Diagnostic reference levels in interventional radiology].

    PubMed

    Vañó Carruana, E; Fernández Soto, J M; Sánchez Casanueva, R M; Ten Morón, J I

    2013-12-01

    This article discusses the diagnostic reference levels for radiation exposure proposed by the International Commission on Radiological Protection (ICRP) to facilitate the application of the optimization criteria in diagnostic imaging and interventional procedures. These levels are normally established as the third quartile of the dose distributions to patients in an ample sample of centers and are supposed to be representative of good practice regarding patient exposure. In determining these levels, it is important to evaluate image quality as well to ensure that it is sufficient for diagnostic purposes. When the values for the dose received by patients are systematically higher or much lower than the reference levels, an investigation should determine whether corrective measures need to be applied. The European and Spanish regulations require the use of these reference values in quality assurance programs. For interventional procedures, the dose area product (or kerma area product) values are usually used as reference values together with the time under fluoroscopy and the total number of images acquired. The most modern imaging devices allow the value of the accumulated dose at the entrance to the patient to be calculated to optimize the distribution of the dose on the skin. The ICRP recommends that the complexity of interventional procedures be taken into account when establishing reference levels. In the future, diagnostic imaging departments will have automatic systems to manage patient dosimetric data; these systems will enable continuous dosage auditing and alerts about individual procedures that might involve doses several times above the reference values. This article also discusses aspects that need to be clarified to take better advantage of the reference levels in interventional procedures. PMID:24211195

  19. Revised reference values for selenium intake.

    PubMed

    Kipp, A P; Strohm, D; Brigelius-Flohé, R; Schomburg, L; Bechthold, A; Leschik-Bonnet, E; Heseker, H

    2015-10-01

    The German, Austrian and Swiss nutrition societies are the joint editors of the 'reference values for nutrient intake'. They have revised the reference values for the intake of selenium and published them in February 2015. The saturation of selenoprotein P (SePP) in plasma is used as a criterion for the derivation of reference values for selenium intake in adults. For persons from selenium-deficient regions (China) SePP saturation was achieved with a daily intake of 49μg of selenium. When using the reference body weights the D-A-CH reference values are based upon, the resulting estimated value for selenium intake is 70μg/day for men and 60μg/day for women. The estimated value for selenium intake for children and adolescents is extrapolated using the estimated value for adults in relation to body weight. For infants aged 0 to under 4 months the estimated value of 10μg/day was derived from the basis of selenium intake via breast milk. For infants aged 4 to under 12 months this estimated value was used and taking into account the differences regarding body weight an estimated value of 15μg/day was derived. For lactating women compared to non-lactating women a higher reference value of 75μg/day is indicated due to the release of selenium with breast milk. The additional selenium requirement for pregnant women is negligible, so that no increased reference value is indicated. PMID:26302929

  20. With Reference to Reference Genes: A Systematic Review of Endogenous Controls in Gene Expression Studies

    PubMed Central

    Chapman, Joanne R.; Waldenström, Jonas

    2015-01-01

    The choice of reference genes that are stably expressed amongst treatment groups is a crucial step in real-time quantitative PCR gene expression studies. Recent guidelines have specified that a minimum of two validated reference genes should be used for normalisation. However, a quantitative review of the literature showed that the average number of reference genes used across all studies was 1.2. Thus, the vast majority of studies continue to use a single gene, with β-actin (ACTB) and/or glyceraldehyde 3-phosphate dehydrogenase (GAPDH) being commonly selected in studies of vertebrate gene expression. Few studies (15%) tested a panel of potential reference genes for stability of expression before using them to normalise data. Amongst studies specifically testing reference gene stability, few found ACTB or GAPDH to be optimal, whereby these genes were significantly less likely to be chosen when larger panels of potential reference genes were screened. Fewer reference genes were tested for stability in non-model organisms, presumably owing to a dearth of available primers in less well characterised species. Furthermore, the experimental conditions under which real-time quantitative PCR analyses were conducted had a large influence on the choice of reference genes, whereby different studies of rat brain tissue showed different reference genes to be the most stable. These results highlight the importance of validating the choice of normalising reference genes before conducting gene expression studies. PMID:26555275

  1. Automatic no-reference image quality assessment.

    PubMed

    Li, Hongjun; Hu, Wei; Xu, Zi-Neng

    2016-01-01

    No-reference image quality assessment aims to predict the visual quality of distorted images without examining the original image as a reference. Most no-reference image quality metrics which have been already proposed are designed for one or a set of predefined specific distortion types and are unlikely to generalize for evaluating images degraded with other types of distortion. There is a strong need of no-reference image quality assessment methods which are applicable to various distortions. In this paper, the authors proposed a no-reference image quality assessment method based on a natural image statistic model in the wavelet transform domain. A generalized Gaussian density model is employed to summarize the marginal distribution of wavelet coefficients of the test images, so that correlative parameters are needed for the evaluation of image quality. The proposed algorithm is tested on three large-scale benchmark databases. Experimental results demonstrate that the proposed algorithm is easy to implement and computational efficient. Furthermore, our method can be applied to many well-known types of image distortions, and achieves a good quality of prediction performance. PMID:27468398

  2. Genotype Imputation with Millions of Reference Samples.

    PubMed

    Browning, Brian L; Browning, Sharon R

    2016-01-01

    We present a genotype imputation method that scales to millions of reference samples. The imputation method, based on the Li and Stephens model and implemented in Beagle v.4.1, is parallelized and memory efficient, making it well suited to multi-core computer processors. It achieves fast, accurate, and memory-efficient genotype imputation by restricting the probability model to markers that are genotyped in the target samples and by performing linear interpolation to impute ungenotyped variants. We compare Beagle v.4.1 with Impute2 and Minimac3 by using 1000 Genomes Project data, UK10K Project data, and simulated data. All three methods have similar accuracy but different memory requirements and different computation times. When imputing 10 Mb of sequence data from 50,000 reference samples, Beagle's throughput was more than 100× greater than Impute2's throughput on our computer servers. When imputing 10 Mb of sequence data from 200,000 reference samples in VCF format, Minimac3 consumed 26× more memory per computational thread and 15× more CPU time than Beagle. We demonstrate that Beagle v.4.1 scales to much larger reference panels by performing imputation from a simulated reference panel having 5 million samples and a mean marker density of one marker per four base pairs. PMID:26748515

  3. Alcohol references on undergraduate males' Facebook profiles.

    PubMed

    Egan, Katie G; Moreno, Megan A

    2011-09-01

    Perceived peer alcohol use is a predictor of consumption in college males; frequent references to alcohol on Facebook may encourage alcohol consumption. Content analysis of college males' Facebook profiles identified references to alcohol. The average age of 225 identified profiles was 19.9 years. Alcohol references were present on 85.3% of the profiles; the prevalence of alcohol was similar across each undergraduate grade. The average number of alcohol references per profile was 8.5 but increased with undergraduate year (p = .003; confidence interval = 1.5, 7.5). Students who were of legal drinking age referenced alcohol 4.5 times more than underage students, and an increase in number of Facebook friends was associated with an increase in displayed alcohol references (p < .001; confidence interval = 0.009, 0.02). Facebook is widely used in the college population; widespread alcohol displays on Facebook may influence social norms and cause increases in male college students' alcohol use. PMID:21406490

  4. Physics of Non-Inertial Reference Frames

    NASA Astrophysics Data System (ADS)

    Kamalov, Timur F.

    2010-12-01

    Physics of non-inertial reference frames is a generalizing of Newton's laws to any reference frames. It is the system of general axioms for classical and quantum mechanics. The first, Kinematics Principle reads: the kinematic state of a body free of forces conserves and equal in absolute value to an invariant of the observer's reference frame. The second, Dynamics Principle extended Newton's second law to non-inertial reference frames and also contains additional variables there are higher derivatives of coordinates. Dynamics Principle reads: a force induces a change in the kinematic state of the body and is proportional to the rate of its change. It is mean that if the kinematic invariant of the reference frame is n-th derivative with respect the time, then the dynamics of a body being affected by the force F is described by the 2n-th differential equation. The third, Statics Principle reads: the sum of all forces acting a body at rest is equal to zero.

  5. Genotype Imputation with Millions of Reference Samples

    PubMed Central

    Browning, Brian L.; Browning, Sharon R.

    2016-01-01

    We present a genotype imputation method that scales to millions of reference samples. The imputation method, based on the Li and Stephens model and implemented in Beagle v.4.1, is parallelized and memory efficient, making it well suited to multi-core computer processors. It achieves fast, accurate, and memory-efficient genotype imputation by restricting the probability model to markers that are genotyped in the target samples and by performing linear interpolation to impute ungenotyped variants. We compare Beagle v.4.1 with Impute2 and Minimac3 by using 1000 Genomes Project data, UK10K Project data, and simulated data. All three methods have similar accuracy but different memory requirements and different computation times. When imputing 10 Mb of sequence data from 50,000 reference samples, Beagle’s throughput was more than 100× greater than Impute2’s throughput on our computer servers. When imputing 10 Mb of sequence data from 200,000 reference samples in VCF format, Minimac3 consumed 26× more memory per computational thread and 15× more CPU time than Beagle. We demonstrate that Beagle v.4.1 scales to much larger reference panels by performing imputation from a simulated reference panel having 5 million samples and a mean marker density of one marker per four base pairs. PMID:26748515

  6. NASA CEV Reference GN&C Architecture

    NASA Technical Reports Server (NTRS)

    Tamblyn, Scott; Hinkel, Heather; Saley, Dave

    2007-01-01

    The Orion Crew Exploration Vehicle (CEV) will be the first human spacecraft built by NASA in almost 3 decades and will be the first vehicle to perform both Low Earth Orbit (LEO) missions and lunar missions since Apollo. The awesome challenge of designing a Guidance, Navigation, and Control (GN&C) system for this vehicle that satisfies all of its various mission requirements is countered by the opportunity to take advantage of the improvements in algorithms, software, sensors, and other related GN&C technology over this period. This paper describes the CEV GN&C reference architecture developed to support the overall NASA reference configuration and validate the driving requirements of the Constellation (Cx) Architecture Requirements Document (CARD, Reference 1) and the CEV System Requirements Document (SRD, Reference 2). The Orion GN&C team designed the reference architecture based on the functional allocation of GN&C roles and responsibilities of CEV with respect to the other Cx vehicles, such as the Crew Launch Vehicle (CLV), Earth Departure Stage (EDS), and Lunar Surface Area Module (LSAM), across all flight phases. The specific challenges and responsibilities of the CEV GN&C system from launch pad to touchdown will be introduced along with an overview of the navigation sensor suite, its redundancy management, and flight software (FSW) architecture. Sensors will be discussed in terms of range of operation, data utility within the navigation system, and rationale for selection. The software architecture is illustrated via block diagrams, commensurate with the design aspects.

  7. Physics of Non-Inertial Reference Frames

    SciTech Connect

    Kamalov, Timur F.

    2010-12-22

    Physics of non-inertial reference frames is a generalizing of Newton's laws to any reference frames. It is the system of general axioms for classical and quantum mechanics. The first, Kinematics Principle reads: the kinematic state of a body free of forces conserves and equal in absolute value to an invariant of the observer's reference frame. The second, Dynamics Principle extended Newton's second law to non-inertial reference frames and also contains additional variables there are higher derivatives of coordinates. Dynamics Principle reads: a force induces a change in the kinematic state of the body and is proportional to the rate of its change. It is mean that if the kinematic invariant of the reference frame is n-th derivative with respect the time, then the dynamics of a body being affected by the force F is described by the 2n-th differential equation. The third, Statics Principle reads: the sum of all forces acting a body at rest is equal to zero.

  8. Reference frequency transmission over optical fiber

    NASA Technical Reports Server (NTRS)

    Lutes, G.; Kirk, A.

    1986-01-01

    A 100-MHz reference frequency from a hydrogen maser frequency standard has been transmitted via optical fiber over a 14-km distance with a measured stability of 1.5 X 10 to the-15 power for 1000 seconds averaging time. This capability was demonstrated in a frequency distribution experiment performed in April, 1986. The reference frequency was transmitted over a single-mode fiber-optic link from Deep Space Station (DSS) 13 to DSS 12 and back. The background leading up to the experiment and the significance of stable reference frequency distribution in the Deep Space Network (DSN) is discussed. Also described are the experiment, including the fiber-optic link, the measurement method and equipment, and finally the results of the experiment.

  9. Integrative analysis of 111 reference human epigenomes

    PubMed Central

    Kundaje, Anshul; Meuleman, Wouter; Ernst, Jason; Bilenky, Misha; Yen, Angela; Kheradpour, Pouya; Zhang, Zhizhuo; Heravi-Moussavi, Alireza; Liu, Yaping; Amin, Viren; Ziller, Michael J; Whitaker, John W; Schultz, Matthew D; Sandstrom, Richard S; Eaton, Matthew L; Wu, Yi-Chieh; Wang, Jianrong; Ward, Lucas D; Sarkar, Abhishek; Quon, Gerald; Pfenning, Andreas; Wang, Xinchen; Claussnitzer, Melina; Coarfa, Cristian; Harris, R Alan; Shoresh, Noam; Epstein, Charles B; Gjoneska, Elizabeta; Leung, Danny; Xie, Wei; Hawkins, R David; Lister, Ryan; Hong, Chibo; Gascard, Philippe; Mungall, Andrew J; Moore, Richard; Chuah, Eric; Tam, Angela; Canfield, Theresa K; Hansen, R Scott; Kaul, Rajinder; Sabo, Peter J; Bansal, Mukul S; Carles, Annaick; Dixon, Jesse R; Farh, Kai-How; Feizi, Soheil; Karlic, Rosa; Kim, Ah-Ram; Kulkarni, Ashwinikumar; Li, Daofeng; Lowdon, Rebecca; Mercer, Tim R; Neph, Shane J; Onuchic, Vitor; Polak, Paz; Rajagopal, Nisha; Ray, Pradipta; Sallari, Richard C; Siebenthall, Kyle T; Sinnott-Armstrong, Nicholas; Stevens, Michael; Thurman, Robert E; Wu, Jie; Zhang, Bo; Zhou, Xin; Beaudet, Arthur E; Boyer, Laurie A; De Jager, Philip; Farnham, Peggy J; Fisher, Susan J; Haussler, David; Jones, Steven; Li, Wei; Marra, Marco; McManus, Michael T; Sunyaev, Shamil; Thomson, James A; Tlsty, Thea D; Tsai, Li-Huei; Wang, Wei; Waterland, Robert A; Zhang, Michael; Chadwick, Lisa H; Bernstein, Bradley E; Costello, Joseph F; Ecker, Joseph R; Hirst, Martin; Meissner, Alexander; Milosavljevic, Aleksandar; Ren, Bing; Stamatoyannopoulos, John A; Wang, Ting; Kellis, Manolis

    2015-01-01

    The reference human genome sequence set the stage for studies of genetic variation and its association with human disease, but a similar reference has lacked for epigenomic studies. To address this need, the NIH Roadmap Epigenomics Consortium generated the largest collection to-date of human epigenomes for primary cells and tissues. Here, we describe the integrative analysis of 111 reference human epigenomes generated as part of the program, profiled for histone modification patterns, DNA accessibility, DNA methylation, and RNA expression. We establish global maps of regulatory elements, define regulatory modules of coordinated activity, and their likely activators and repressors. We show that disease and trait-associated genetic variants are enriched in tissue-specific epigenomic marks, revealing biologically-relevant cell types for diverse human traits, and providing a resource for interpreting the molecular basis of human disease. Our results demonstrate the central role of epigenomic information for understanding gene regulation, cellular differentiation, and human disease. PMID:25693563

  10. Reference Frames in Earth Rotation Theories

    NASA Astrophysics Data System (ADS)

    Ferrándiz, José M.; Belda, Santiago; Heinkelmann, Robert; Getino, Juan; Schuh, Harald; Escapa, Alberto

    2015-04-01

    Nowadays the determination of the Earth Orientation Parameters (EOP) and the different Terrestrial Reference Frames (TRF) are not independent. The available theories of Earth rotation aims at providing the orientation of a certain reference system linked somehow to the Earth with respect to a given celestial system, considered as inertial. In the past years a considerable effort has been dedicated to the improvement of the TRF realizations, following the lines set up in the 1980's. However, the reference systems used in the derivation of the theories have been rather considered as something fully established, not deserving a special attention. In this contribution we review the definitions of the frames used in the main theoretical approaches, focusing on those used in the construction of IAU2000, and the extent to which their underlying hypotheses hold. The results are useful to determine the level of consistency of the predicted and determined EOP.

  11. Comparison of select reference management tools.

    PubMed

    Zhang, Yingting

    2012-01-01

    Bibliographic management tools have been widely used by researchers to store, organize, and manage their references for research papers, theses, dissertations, journal articles, and other publications. There are a number of reference management tools available. In order for users to decide which tool is best for their needs, it is important to know each tool's strengths and weaknesses. This article compares four reference management tools, one of which is licensed by University of Medicine and Dentistry of New Jersey libraries and the other three are open source and freely available. They were chosen based on their functionality, ease of use, availability to library users, and popularity. These four tools are EndNote/EndNote Web, Zotero, Connotea, and Mendeley Desktop/Mendeley Web. Each tool is analyzed in terms of the following features: accessing, collecting, organizing, collaborating, and citing/formatting. A comparison table is included to summarize the key features of these tools. PMID:22289095

  12. International Geomagnetic Reference Field: the third generation.

    USGS Publications Warehouse

    Peddie, N.W.

    1982-01-01

    In August 1981 the International Association of Geomagnetism and Aeronomy revised the International Geomagnetic Reference Field (IGRF). It is the second revision since the inception of the IGRF in 1968. The revision extends the earlier series of IGRF models from 1980 to 1985, introduces a new series of definitive models for 1965-1976, and defines a provisional reference field for 1975- 1980. The revision consists of: 1) a model of the main geomagnetic field at 1980.0, not continuous with the earlier series of IGRF models together with a forecast model of the secular variation of the main field during 1980-1985; 2) definitive models of the main field at 1965.0, 1970.0, and 1975.0, with linear interpolation of the model coefficients specified for intervening dates; and 3) a provisional reference field for 1975-1980, defined as the linear interpolation of the 1975 and 1980 main-field models.-from Author

  13. Frequency References for Gravitational Wave Missions

    NASA Technical Reports Server (NTRS)

    Preston, Alix; Thrope, J. I.; Donelan, D.; Miner, L.

    2012-01-01

    The mitigation of laser frequency noise is an important aspect of interferometry for LISA-like missions. One portion of the baseline mitigation strategy in LISA is active stabilization utilizing opto-mechanical frequency references. The LISA optical bench is an attractive place to implement such frequency references due to its environmental stability and its access to primary and redundant laser systems. We have made an initial investigation of frequency references constructed using the techniques developed for the LISA and LISA Pathfinder optical benches. Both a Mach-Zehnder interferometer and triangular Fabry-Perot cavity have been successfully bonded to a Zerodur baseplate using the hydroxide bonding method. We will describe the construction of the bench along with preliminary stability results.

  14. Integrative analysis of 111 reference human epigenomes.

    PubMed

    Kundaje, Anshul; Meuleman, Wouter; Ernst, Jason; Bilenky, Misha; Yen, Angela; Heravi-Moussavi, Alireza; Kheradpour, Pouya; Zhang, Zhizhuo; Wang, Jianrong; Ziller, Michael J; Amin, Viren; Whitaker, John W; Schultz, Matthew D; Ward, Lucas D; Sarkar, Abhishek; Quon, Gerald; Sandstrom, Richard S; Eaton, Matthew L; Wu, Yi-Chieh; Pfenning, Andreas R; Wang, Xinchen; Claussnitzer, Melina; Liu, Yaping; Coarfa, Cristian; Harris, R Alan; Shoresh, Noam; Epstein, Charles B; Gjoneska, Elizabeta; Leung, Danny; Xie, Wei; Hawkins, R David; Lister, Ryan; Hong, Chibo; Gascard, Philippe; Mungall, Andrew J; Moore, Richard; Chuah, Eric; Tam, Angela; Canfield, Theresa K; Hansen, R Scott; Kaul, Rajinder; Sabo, Peter J; Bansal, Mukul S; Carles, Annaick; Dixon, Jesse R; Farh, Kai-How; Feizi, Soheil; Karlic, Rosa; Kim, Ah-Ram; Kulkarni, Ashwinikumar; Li, Daofeng; Lowdon, Rebecca; Elliott, GiNell; Mercer, Tim R; Neph, Shane J; Onuchic, Vitor; Polak, Paz; Rajagopal, Nisha; Ray, Pradipta; Sallari, Richard C; Siebenthall, Kyle T; Sinnott-Armstrong, Nicholas A; Stevens, Michael; Thurman, Robert E; Wu, Jie; Zhang, Bo; Zhou, Xin; Beaudet, Arthur E; Boyer, Laurie A; De Jager, Philip L; Farnham, Peggy J; Fisher, Susan J; Haussler, David; Jones, Steven J M; Li, Wei; Marra, Marco A; McManus, Michael T; Sunyaev, Shamil; Thomson, James A; Tlsty, Thea D; Tsai, Li-Huei; Wang, Wei; Waterland, Robert A; Zhang, Michael Q; Chadwick, Lisa H; Bernstein, Bradley E; Costello, Joseph F; Ecker, Joseph R; Hirst, Martin; Meissner, Alexander; Milosavljevic, Aleksandar; Ren, Bing; Stamatoyannopoulos, John A; Wang, Ting; Kellis, Manolis

    2015-02-19

    The reference human genome sequence set the stage for studies of genetic variation and its association with human disease, but epigenomic studies lack a similar reference. To address this need, the NIH Roadmap Epigenomics Consortium generated the largest collection so far of human epigenomes for primary cells and tissues. Here we describe the integrative analysis of 111 reference human epigenomes generated as part of the programme, profiled for histone modification patterns, DNA accessibility, DNA methylation and RNA expression. We establish global maps of regulatory elements, define regulatory modules of coordinated activity, and their likely activators and repressors. We show that disease- and trait-associated genetic variants are enriched in tissue-specific epigenomic marks, revealing biologically relevant cell types for diverse human traits, and providing a resource for interpreting the molecular basis of human disease. Our results demonstrate the central role of epigenomic information for understanding gene regulation, cellular differentiation and human disease. PMID:25693563

  15. Lymphocytes subsets reference values in childhood.

    PubMed

    Tosato, F; Bucciol, G; Pantano, G; Putti, M C; Sanzari, M C; Basso, G; Plebani, M

    2015-01-01

    Immunophenotyping of blood lymphocyte subsets and activation markers is a basic tool in the diagnostic process of primary immunodeficiency diseases, its use becoming more and more widespread as the knowledge about these illnesses increases. However, the availability of reliable reference values, which need to be age-matched for the pediatric population, is a pre-requisite for the reliable interpretation of immunophenotyping data. Aim of this study is to analyze the lymphocyte subsets and activation markers distribution in children aged 0-18 years referring to the University Hospital of Padova and to create age-matched reference values expressed by percentiles, thus providing a valuable guideline for the interpretation of the immunophenotype. PMID:25132325

  16. The CEBAF fiber optic phase reference system

    SciTech Connect

    Crawford, K.; Simrock, S.; Hovater, C.; Krycuk, A.

    1995-12-31

    The specified phase stability of the CEBAF RF distribution system is 2.9{degree} rms per linac. Stability is achieved through the use of a temperature and pressure regulated coaxial drive line. Purpose of the fiber optic phase reference system is to monitor the relative phase at the beginning and ending of this drive line, between linacs, injector and separator to determine drift due to ambient temperature fluctuations. The system utilizes an Ortel 1310 nm single mode laser driving Sumitumo optical fiber to distribute a reference signal at 1497 MHz. Phase of this reference signal is compared to the 1427 MHz (LO) and the 70 MHz (IF) via a 360{degree} phase detector. The detected information is then routed to the CEBAF control system for display with a specified resolution of {+-}0.2{degree} over a 20{degree} phase delta.

  17. Development of solid thorium-232 reference materials

    SciTech Connect

    Engelder, P.R.; Donivan, S.; Chessmore, R.B.

    1985-05-01

    Thorium-232 reference materials having a matrix similar to soil and uranium-mill tailings are necessary for ensuring uniform standardization among measurements performed by remedial-action contractors. A task was undertaken by the Technical Measurements Center (TMC) to prepare some 200 pounds each of three different concentrations of Th-232 reference material by diluting a thorium ore with soil. Target values for Th-232 content were 70, 30, and 10 pCi/g. The recommended thorium-232 concentrations for the three reference materials are 71.2 +- 2.0 pCi/g, 30.5 +- 0.6 pCi/g, and 10.2 +- 0.3 pCi/g.

  18. Facilitating Physician Access to Medical Reference Information

    PubMed Central

    Bellman, Philip; Havens, Carol; Bertolucci, Ysabel; Streeter, Beth

    2005-01-01

    Context: Computer-based medical reference information is augmenting—and in some cases, replacing—many traditional sources. For Kaiser Permanente (KP) physicians, this change presents both advantages and obstacles to finding medical reference information. Objective: To improve understanding of physician information-seeking behavior and the barriers that limit use of both print-based and computer-based medical reference resources. Design: During 2002 and 2003, two quality-improvement surveys were distributed to full-time KP physicians. Survey instruments sent by conventional mail and by e-mail were based on results of telephone interviews and focus groups, and were designed to be concise and easy to use. Participant response rates exceeded 83%. Outcomes Measures: The surveys examined physician use of online medical reference information, medical libraries and services, self-directed learning resources, and continuing medical education (CME). Results: Of the physicians who responded to the survey, 89% used online resources frequently to enhance care, to inform clinical decisions, to update knowledge, to educate patients, or for a combination of these purposes. Compared with responses from older physicians, responses from younger physicians showed a greater proclivity for using nearly all types of online information. Most physicians obtained CME credits primarily through in-person education programs; few physicians used self-directed electronic learning tools. Obstacles to effective access to information included lack of time, overly complex access methods, and lack of awareness about available resources. Conclusions: A considerable gap exists between physicians' need for information and the resources currently available for delivering this information. Although we observed a clear shift from using printed medical references to using computer-based resources, many barriers prevent their effective use. Clinicians need easy-to-use, seamless systems of medical

  19. European Vertical Reference System Influence in Latvia

    NASA Astrophysics Data System (ADS)

    Celms, A.; Reķe, I.; Ratkevičs, A.

    2015-11-01

    Till 1 December, 2014, in Latvia the heights were determined in Baltic Normal Height System 1977. The national height system is determined by the Cabinet of Ministers and internal laws. Now for the change of the national height system to reconcile it with the European Vertical Reference System, amendments to the laws and regulations have been developed, but so far only the amendment to the Geospatial Information Law is in force, the amendment to the regulation of the Cabinet of Ministers is still not approved. This amendment declares the Latvia Height System based on the European Vertical Reference System in Latvia as the national height system. For height transformation, there is a transformation formula for each European country. After calculations it is seen that height difference between Baltic Normal Height System 1977 and European Vertical Reference System depends on point location in the territory (coordinates). This unequal height difference between both height systems will cause unequal height values on border connection points between Baltic countries. The aim of the research is to evaluate the European Vertical Reference System in Latvia. To reach the aim the following tasks are set: 1) to evaluate the components of transformation formulas; 2) using the transformation formulas to calculate height differences between Baltic Normal Height System 1977 and the European Vertical Reference System realization EVRF2007 for the territory of Latvia and also between Baltic Normal Height System 1977 and the Latvia Normal Height System; 3) to get height differences in the European Vertical Reference System on the borderlines of Latvia - Estonia and Latvia - Lithuania.

  20. Reference in human and non-human primate communication: What does it take to refer?

    PubMed

    Sievers, Christine; Gruber, Thibaud

    2016-07-01

    The concept of functional reference has been used to isolate potentially referential vocal signals in animal communication. However, its relatedness to the phenomenon of reference in human language has recently been brought into question. While some researchers have suggested abandoning the concept of functional reference altogether, others advocate a revision of its definition to include contextual cues that play a role in signal production and perception. Empirical and theoretical work on functional reference has also put much emphasis on how the receiver understands the referential signal. However, reference, as defined in the linguistic literature, is an action of the producer, and therefore, any definition describing reference in non-human animals must also focus on the producer. To successfully determine whether a signal is used to refer, we suggest an approach from the field of pragmatics, taking a closer look at specific situations of signal production, specifically at the factors that influence the production of a signal by an individual. We define the concept of signaller's reference to identify intentional acts of reference produced by a signaller independently of the communicative modality, and illustrate it with a case study of the hoo vocalizations produced by wild chimpanzees during travel. This novel framework introduces an intentional approach to referentiality. It may therefore permit a closer comparison of human and non-human animal referential behaviour and underlying cognitive processes, allowing us to identify what may have emerged solely in the human lineage. PMID:26971953

  1. The Region 4 collaborative virtual reference project.

    PubMed

    Parker, Sandi K; Johnson, E Diane

    2003-01-01

    In May 2002, the Denison Memorial Library at the University of Colorado Health Sciences Center and the J. Otto Lottes Health Sciences Library at the University of Missouri-Columbia, with funding from the National Network of Libraries of Medicine-Midcontinental Region, embarked on a collaborative, real-time reference project using the 24/7 Reference, Inc., software package. This paper describes how the project was conceived, and includes details on the service hours, staffing, training, marketing, lessons learned, and future plans for the service. PMID:12723812

  2. Organizing Search Results with a Reference Map.

    PubMed

    Nocaj, A; Brandes, U

    2012-12-01

    We propose a method to highlight query hits in hierarchically clustered collections of interrelated items such as digital libraries or knowledge bases. The method is based on the idea that organizing search results similarly to their arrangement on a fixed reference map facilitates orientation and assessment by preserving a user's mental map. Here, the reference map is built from an MDS layout of the items in a Voronoi treemap representing their hierarchical clustering, and we use techniques from dynamic graph layout to align query results with the map. The approach is illustrated on an archive of newspaper articles. PMID:26357163

  3. Preparation of Reference Material 8504, Transformer Oil

    PubMed Central

    Poster, Dianne L.; Schantz, Michele M.; Wise, Stephen A.

    2005-01-01

    A new reference material (RM), RM 8504, has been prepared for use as a diluent oil with Aroclors in transformer oil Standard Reference Materials (SRMs) 3075 to 3080 and SRM 3090 when developing and validating methods for the determination of polychlorinated biphenyls (PCBs) as Aroclors in transformer oil or similar matrices. SRMs 3075-3080 and SRM 3090 consist of individual Aroclors in the same transformer oil that was used to prepare RM 8504. A unit of RM 8504 consists of one bottle containing approximately 100 mL of transformer oil. No additional constituents have been added to the oil. PMID:27308183

  4. Ray Effect Mitigation Through Reference Frame Rotation

    DOE PAGESBeta

    Tencer, John

    2016-06-14

    The discrete ordinates method is a popular and versatile technique for solving the radiative transport equation, a major drawback of which is the presence of ray effects. Mitigation of ray effects can yield significantly more accurate results and enhanced numerical stability for combined mode codes. Moreover, when ray effects are present, the solution is seen to be highly dependent upon the relative orientation of the geometry and the global reference frame. It is an undesirable property. A novel ray effect mitigation technique of averaging the computed solution for various reference frame orientations is proposed.

  5. Multiple reference frames in haptic spatial processing

    NASA Astrophysics Data System (ADS)

    Volčič, R.

    2008-08-01

    The present thesis focused on haptic spatial processing. In particular, our interest was directed to the perception of spatial relations with the main focus on the perception of orientation. To this end, we studied haptic perception in different tasks, either in isolation or in combination with vision. The parallelity task, where participants have to match the orientations of two spatially separated bars, was used in its two-dimensional and three-dimensional versions in Chapter 2 and Chapter 3, respectively. The influence of non-informative vision and visual interference on performance in the parallelity task was studied in Chapter 4. A different task, the mental rotation task, was introduced in a purely haptic study in Chapter 5 and in a visuo-haptic cross-modal study in Chapter 6. The interaction of multiple reference frames and their influence on haptic spatial processing were the common denominators of these studies. In this thesis we approached the problems of which reference frames play the major role in haptic spatial processing and how the relative roles of distinct reference frames change depending on the available information and the constraints imposed by different tasks. We found that the influence of a reference frame centered on the hand was the major cause of the deviations from veridicality observed in both the two-dimensional and three-dimensional studies. The results were described by a weighted average model, in which the hand-centered egocentric reference frame is supposed to have a biasing influence on the allocentric reference frame. Performance in haptic spatial processing has been shown to depend also on sources of information or processing that are not strictly connected to the task at hand. When non-informative vision was provided, a beneficial effect was observed in the haptic performance. This improvement was interpreted as a shift from the egocentric to the allocentric reference frame. Moreover, interfering visual information presented

  6. Geoscience laser altimeter system - stellar reference system

    SciTech Connect

    Millar, Pamela S.; Sirota, J. Marcos

    1998-01-15

    GLAS is an EOS space-based laser altimeter being developed to profile the height of the Earth's ice sheets with {approx}15 cm single shot accuracy from space under NASA's Mission to Planet Earth (MTPE). The primary science goal of GLAS is to determine if the ice sheets are increasing or diminishing for climate change modeling. This is achieved by measuring the ice sheet heights over Greenland and Antarctica to 1.5 cm/yr over 100 kmx100 km areas by crossover analysis (Zwally 1994). This measurement performance requires the instrument to determine the pointing of the laser beam to {approx}5 urad (1 arcsecond), 1-sigma, with respect to the inertial reference frame. The GLAS design incorporates a stellar reference system (SRS) to relate the laser beam pointing angle to the star field with this accuracy. This is the first time a spaceborne laser altimeter is measuring pointing to such high accuracy. The design for the stellar reference system combines an attitude determination system (ADS) with a laser reference system (LRS) to meet this requirement. The SRS approach and expected performance are described in this paper.

  7. Internet Reference Sources in the Performing Arts.

    ERIC Educational Resources Information Center

    AmRhein, Richard

    1997-01-01

    There are a number of Web-based Internet resources available in the performance arts, created by hobbyists, amateurs, professionals, and corporations for commercial and recreational purposes. Collected here are Internet sites in the areas of music, dance, film/cinema, and theater/drama that are useful when answering typical reference questions in…

  8. 33 CFR 241.3 - References.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... Information Services, 5285 Port Royal Road, Springfield, VA 22161. References (a), (b) and (c) may be reviewed in your local library or by writing your local Congressperson. (a) Water Resources Development Act, 1986, Public Law 99-662, 100 Stat. 4082, 33 U.S.C. 2201 et seq. (b) Water Resources Development...

  9. Veterinary Accreditation. A Reference Guide for Practitioners.

    ERIC Educational Resources Information Center

    Animal and Plant Health Inspection Service (USDA), Washington, DC.

    This reference manual was designed as a guide for veterinarians who have been accredited by the U.S. Department of Agriculture (USDA) Animal and Plant Health Inspection Services. The guide provides instructions on the following topics: identifying animals, reportable diseases and conditions, brucellosis, tuberculosis, pseudorabies, miscellaneous…

  10. The Reference Desk: Service Point or Barrier?

    ERIC Educational Resources Information Center

    Larason, Larry; Robinson, Judith Schiek

    1984-01-01

    Discussion of theoretical considerations and practical factors relating to use of library reference service highlights factors involved in desk approachability--need, communication and promotion, physical arrangement of department, positioning (which gives the product a clear image communicating its purpose or use), psychological cost (personal…

  11. SELECTED REFERENCES FOR EARTH SCIENCE COURSES.

    ERIC Educational Resources Information Center

    MATTHEWS, WILLIAM H., III

    LISTED ARE TEXTBOOKS, TEACHING GUIDES, PERIODICALS, AND OTHER REFERENCES CONTAINING CLASSROOM TEACHING AIDS, LABORATORY AND FIELD SUGGESTIONS, AND OTHER MATERIALS IN THE FIELDS OF ASTRONOMY, GEOLOGY, METEOROLOGY, OCEANOLOGY, AND PHYSICAL GEOGRAPHY. THEY ARE DESIGNED TO AID ELEMENTARY AND SECONDARY SCHOOL TEACHERS IN THE PRESENTATION OF EARTH…

  12. Ball and Roller Bearings. A Teaching Reference.

    ERIC Educational Resources Information Center

    American Association for Vocational Instructional Materials, Athens, GA.

    The manual provides a subject reference for ball and roller bearings. The following topics are included: (1) bearing nomenclature, (2) bearing uses, (3) bearing capacities, (4) shop area working conditions, (5) bearing removal, (6) bearing cleaning and inspection, (7) bearing replacement, (8) bearing lubrication, (9) bearing installation, (10)…

  13. 36 CFR 330.3 - References.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ...) Section 120 of the Water Resource Development Act of 1976 (Pub. L. 94-587, 90 Stat. 2917). (d) 36 CFR... 36 Parks, Forests, and Public Property 3 2013-07-01 2012-07-01 true References. 330.3 Section 330... ENFORCEMENT SERVICES CONTRACTS AT CIVIL WORKS WATER RESOURCE PROJECTS ADMINISTERED BY THE CHIEF OF...

  14. The Northwest Territories. Reference Series No. 35.

    ERIC Educational Resources Information Center

    Department of External Affairs, Ottawa (Ontario).

    This booklet, one of a series featuring the Canadian provinces, presents a brief overview of Northwest Territories and is suitable for teacher reference or student reading. Separate sections discuss geography, history and people, land claims, the economy, the government, and recreation and the arts. Specific topics include the expansive size and…

  15. Preventing Sexual Abuse. Reference Sheet 8.

    ERIC Educational Resources Information Center

    Britton, Patti O., Ed.; McGee, Michael, Ed.

    This reference book, developed to present options for the prevention and treatment of child sexual abuse, contains descriptions of creative approaches used to address the problem of child sexual abuse. Some of the programs described offer active and entertaining interventions, such as puppet shows, coloring books, stories, teddy bears, and…

  16. NACA Member Legislative Reference Guide, 2001. Revised.

    ERIC Educational Resources Information Center

    Amato, Tracey L.

    Calling for action on a wide range of children's issues, this guide of the National Association of Child Advocates (NACA) delineates the state legislative agendas of 41 of its members from 33 states. The reference guide is presented in three sections. Section 1 contains the legislative priorities by topic area in a chart format indicating the…

  17. A Basic Reference Grammar of Slovene.

    ERIC Educational Resources Information Center

    Derbyshire, William W.

    This reference grammar is intended for adult speakers of English who are at the elementary through the intermediate levels of acquisition of the Slovene language. It begins with a brief description of the Slovene language, its major dialects and its place among the Slavic languages. Information on the alphabet, pronunciation, and spelling rules…

  18. Women's Studies: A Guide to Reference Sources.

    ERIC Educational Resources Information Center

    Waiser, Joni, Comp.

    Approximately 125 reference materials on women's studies located in the McClennan Library, McGill University (Montreal), are cited in this annotated bibliography. The bibliography serves as an introduction to social science and humanities materials on women. Library of Congress call numbers are included; dates of publication range from the late…

  19. Comparative Elections: Building a Basic Reference Collection.

    ERIC Educational Resources Information Center

    Nalen, James E.

    2001-01-01

    This annotated bibliography focuses on resources for the study of international elections and electoral systems and outcomes that will be useful for collection development and for answering reference questions about foreign elections. Discusses comparative politics, comparative elections, and possible electoral reform. (LRW)

  20. Russian Literature: A Guide to Reference Sources.

    ERIC Educational Resources Information Center

    McGill Univ., Montreal (Quebec). McLennan Library.

    An annotated bibliography of general and specialized reference works for Russian and Soviet literature is intended for both students and researchers. English language and Russian language sources in the McGill University (Canada) libraries are included. Subject headings include guides (to the literature and to archival resources), encyclopedias,…

  1. 32 CFR 552.86 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... CEMETERIES REGULATIONS AFFECTING MILITARY RESERVATIONS Fort Lewis Land Use Policy § 552.86 References. (a) AR 405-70 (Utilization of Real Estate). (b) AR 405-80 (Granting Use of Real Estate). (c) AR 420-74 (Natural Resources—Land, Forest, and Wildlife Management). (d) FL Reg 215-1 (Hunting, Fishing, and...

  2. 32 CFR 552.161 - References.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 32 National Defense 3 2014-07-01 2014-07-01 false References. 552.161 Section 552.161 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY MILITARY RESERVATIONS AND NATIONAL CEMETERIES REGULATIONS AFFECTING MILITARY RESERVATIONS Land Use Policy for Fort Lewis, Yakima Training...

  3. 32 CFR 552.86 - References.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... CEMETERIES REGULATIONS AFFECTING MILITARY RESERVATIONS Fort Lewis Land Use Policy § 552.86 References. (a) AR 405-70 (Utilization of Real Estate). (b) AR 405-80 (Granting Use of Real Estate). (c) AR 420-74 (Natural Resources—Land, Forest, and Wildlife Management). (d) FL Reg 215-1 (Hunting, Fishing, and...

  4. 32 CFR 552.86 - References.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... CEMETERIES REGULATIONS AFFECTING MILITARY RESERVATIONS Fort Lewis Land Use Policy § 552.86 References. (a) AR 405-70 (Utilization of Real Estate). (b) AR 405-80 (Granting Use of Real Estate). (c) AR 420-74 (Natural Resources—Land, Forest, and Wildlife Management). (d) FL Reg 215-1 (Hunting, Fishing, and...

  5. 32 CFR 552.161 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 3 2010-07-01 2010-07-01 true References. 552.161 Section 552.161 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY MILITARY RESERVATIONS AND NATIONAL CEMETERIES REGULATIONS AFFECTING MILITARY RESERVATIONS Land Use Policy for Fort Lewis, Yakima Training...

  6. 32 CFR 552.86 - References.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... CEMETERIES REGULATIONS AFFECTING MILITARY RESERVATIONS Fort Lewis Land Use Policy § 552.86 References. (a) AR 405-70 (Utilization of Real Estate). (b) AR 405-80 (Granting Use of Real Estate). (c) AR 420-74 (Natural Resources—Land, Forest, and Wildlife Management). (d) FL Reg 215-1 (Hunting, Fishing, and...

  7. 32 CFR 552.161 - References.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 32 National Defense 3 2012-07-01 2009-07-01 true References. 552.161 Section 552.161 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY MILITARY RESERVATIONS AND NATIONAL CEMETERIES REGULATIONS AFFECTING MILITARY RESERVATIONS Land Use Policy for Fort Lewis, Yakima Training...

  8. 32 CFR 552.161 - References.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 32 National Defense 3 2011-07-01 2009-07-01 true References. 552.161 Section 552.161 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY MILITARY RESERVATIONS AND NATIONAL CEMETERIES REGULATIONS AFFECTING MILITARY RESERVATIONS Land Use Policy for Fort Lewis, Yakima Training...

  9. 32 CFR 552.161 - References.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 32 National Defense 3 2013-07-01 2013-07-01 false References. 552.161 Section 552.161 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY MILITARY RESERVATIONS AND NATIONAL CEMETERIES REGULATIONS AFFECTING MILITARY RESERVATIONS Land Use Policy for Fort Lewis, Yakima Training...

  10. 32 CFR 552.86 - References.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... CEMETERIES REGULATIONS AFFECTING MILITARY RESERVATIONS Fort Lewis Land Use Policy § 552.86 References. (a) AR 405-70 (Utilization of Real Estate). (b) AR 405-80 (Granting Use of Real Estate). (c) AR 420-74 (Natural Resources—Land, Forest, and Wildlife Management). (d) FL Reg 215-1 (Hunting, Fishing, and...

  11. The Elementary Reading Reference Guide. Revised.

    ERIC Educational Resources Information Center

    Fairbanks North Star Borough School District, AK.

    Designed to complement the RIM (Reading-Instruction-Maintenance) Reading Skill Guide, this reference guide provides a useful tool for teachers utilizing the RIM Model in grades kindergarten through six. In the RIM model, readiness (R) stands for exposure to the skill, mastery not expected; instruction (I) stands for formal presentation with…

  12. Sextant measures spacecraft altitude without gravitational reference

    NASA Technical Reports Server (NTRS)

    1966-01-01

    Horizon-sensing sextant measures the altitude of an orbiting spacecraft without gravitational reference by optically measuring the dip angle to the horizon along a line of sight in each of two planes. The sextant scans over a relatively limited field of view.

  13. 40 CFR 1042.910 - Reference materials.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... reference as prescribed in 5 U.S.C. 552(a) and 1 CFR part 51. Anyone may inspect copies at the U.S. EPA, Air.../federal_register/code_of_federal_regulations/ibr_locations.html. (a) IMO material. This paragraph...

  14. 28 CFR 63.3 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ....) and NFIP criteria (44 CFR part 59 et seq.). (d) Flood Disaster Protection Act of 1973 (Pub. L. 93-234... Administration DEPARTMENT OF JUSTICE (CONTINUED) FLOODPLAIN MANAGEMENT AND WETLAND PROTECTION PROCEDURES § 63.3 References. (a) Unified National Program for Floodplain Management, Water Resources Council, which...

  15. 28 CFR 63.3 - References.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ....) and NFIP criteria (44 CFR part 59 et seq.). (d) Flood Disaster Protection Act of 1973 (Pub. L. 93-234... Administration DEPARTMENT OF JUSTICE (CONTINUED) FLOODPLAIN MANAGEMENT AND WETLAND PROTECTION PROCEDURES § 63.3 References. (a) Unified National Program for Floodplain Management, Water Resources Council, which...

  16. 28 CFR 63.3 - References.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ....) and NFIP criteria (44 CFR part 59 et seq.). (d) Flood Disaster Protection Act of 1973 (Pub. L. 93-234... Administration DEPARTMENT OF JUSTICE (CONTINUED) FLOODPLAIN MANAGEMENT AND WETLAND PROTECTION PROCEDURES § 63.3 References. (a) Unified National Program for Floodplain Management, Water Resources Council, which...

  17. 28 CFR 63.3 - References.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ....) and NFIP criteria (44 CFR part 59 et seq.). (d) Flood Disaster Protection Act of 1973 (Pub. L. 93-234... Administration DEPARTMENT OF JUSTICE (CONTINUED) FLOODPLAIN MANAGEMENT AND WETLAND PROTECTION PROCEDURES § 63.3 References. (a) Unified National Program for Floodplain Management, Water Resources Council, which...

  18. 28 CFR 63.3 - References.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ....) and NFIP criteria (44 CFR part 59 et seq.). (d) Flood Disaster Protection Act of 1973 (Pub. L. 93-234... Administration DEPARTMENT OF JUSTICE (CONTINUED) FLOODPLAIN MANAGEMENT AND WETLAND PROTECTION PROCEDURES § 63.3 References. (a) Unified National Program for Floodplain Management, Water Resources Council, which...

  19. Environmental Reference Series, Conservation and Wildlife.

    ERIC Educational Resources Information Center

    Qutub, Musa, Comp.

    Compiled in this reference work are bibliographic citations for books and articles dealing with the environment and influences upon it. Specific categories are conservation and wildlife and pesticides. Items are indexed only by title but information about author, source, and date of publication is also noted. (BL)

  20. Archaeology: A Guide to Reference Sources.

    ERIC Educational Resources Information Center

    Morrison, Doreen, Comp.

    This bibliographic guide lists reference sources available at McGill University for research in prehistory and non-classical archaeology. No exclusively biographical sources have been included, but many of the encyclopedias and handbooks contain biographical information and are annotated accordingly. Titles are listed in the following categories:…

  1. Reference Lists for HECE Occupational Areas.

    ERIC Educational Resources Information Center

    Texas Education Agency, Austin. Dept. of Occupational Education and Technology.

    The annotated bibliography contains citations to appropriate reference books, pamphlets and audiovisual materials for the following 17 occupations: art and craft aide, bridal consultant, child care aide, clothing assistant, companion to the elderly, consumer aide, dietetic aide, fabric coordinator, fashion coordinator, floral designer, food…

  2. Part B Excess Cost Quick Reference Document

    ERIC Educational Resources Information Center

    Ball, Wayne; Beridon, Virginia; Hamre, Kent; Morse, Amanda

    2011-01-01

    This Quick Reference Document has been prepared by the Regional Resource Center Program ARRA/Fiscal Priority Team to aid RRCP State Liaisons and other (Technical Assistance) TA providers in understanding the general context of state questions surrounding excess cost. As a "first-stop" for TA providers in investigating excess cost questions on…

  3. Xyce parallel electronic simulator : reference guide.

    SciTech Connect

    Mei, Ting; Rankin, Eric Lamont; Thornquist, Heidi K.; Santarelli, Keith R.; Fixel, Deborah A.; Coffey, Todd Stirling; Russo, Thomas V.; Schiek, Richard Louis; Warrender, Christina E.; Keiter, Eric Richard; Pawlowski, Roger Patrick

    2011-05-01

    This document is a reference guide to the Xyce Parallel Electronic Simulator, and is a companion document to the Xyce Users Guide. The focus of this document is (to the extent possible) exhaustively list device parameters, solver options, parser options, and other usage details of Xyce. This document is not intended to be a tutorial. Users who are new to circuit simulation are better served by the Xyce Users Guide. The Xyce Parallel Electronic Simulator has been written to support, in a rigorous manner, the simulation needs of the Sandia National Laboratories electrical designers. It is targeted specifically to run on large-scale parallel computing platforms but also runs well on a variety of architectures including single processor workstations. It also aims to support a variety of devices and models specific to Sandia needs. This document is intended to complement the Xyce Users Guide. It contains comprehensive, detailed information about a number of topics pertinent to the usage of Xyce. Included in this document is a netlist reference for the input-file commands and elements supported within Xyce; a command line reference, which describes the available command line arguments for Xyce; and quick-references for users of other circuit codes, such as Orcad's PSpice and Sandia's ChileSPICE.

  4. Positional reference system for ultraprecision machining

    DOEpatents

    Arnold, Jones B.; Burleson, Robert R.; Pardue, Robert M.

    1982-01-01

    A stable positional reference system for use in improving the cutting tool-to-part contour position in numerical controlled-multiaxis metal turning machines is provided. The reference system employs a plurality of interferometers referenced to orthogonally disposed metering bars which are substantially isolated from machine strain induced position errors for monitoring the part and tool positions relative to the metering bars. A microprocessor-based control system is employed in conjunction with the plurality of position interferometers and part contour description data inputs to calculate error components for each axis of movement and output them to corresponding axis drives with appropriate scaling and error compensation. Real-time position control, operating in combination with the reference system, makes possible the positioning of the cutting points of a tool along a part locus with a substantially greater degree of accuracy than has been attained previously in the art by referencing and then monitoring only the tool motion relative to a reference position located on the machine base.

  5. FINE PARTICLE EMISSIONS INFORMATION SYSTEM REFERENCE MANUAL

    EPA Science Inventory

    The report is a basic reference manual on the Fine Particle Emissions Information System (FPEIS), a computerized database on primary fine particle emissions to the atmosphere from stationary point sources. The FPEIS is a component of the Environmental Assessment Data Systems (EAD...

  6. 32 CFR 865.101 - References.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE ORGANIZATION AND MISSION-GENERAL PERSONNEL REVIEW BOARDS Air Force Discharge Review Board § 865.101 References. (a) Title 10 U.S.C., section... Directive 1332.14, “Enlisted Administrative Separations,” January 28, 1982. (g) DOD Directive 5400.7,...

  7. The Art and Science of Reference Checking

    ERIC Educational Resources Information Center

    Perry, Robert Hastings

    2004-01-01

    If we could survey academic chief executive search committees across higher education, a composite definition of reference checking would likely include verification of factual information such as dates of employment, job titles, and responsibilities, as well as an evaluation of successful performance and leadership skills. Although everyone would…

  8. Handbook of Reference Sources. Second Edition.

    ERIC Educational Resources Information Center

    Nichols, Margaret Irby

    Designed to serve as a selection aid for small public libraries and to list important sources available through the major resource centers of the Texas Library System, this bibliography lists 804 annotated reference sources with 126 additional works named within the annotations. The books are grouped into 18 major areas, each of which is broken…

  9. Handbook of Reference Sources. Third Edition.

    ERIC Educational Resources Information Center

    Nichols, Margaret Irby

    This third edition of popular and useful reference works, which emphasizes the needs of small libraries, contains 975 annotated entries and lists 201 additional titles (most with bibliographic and order information) in the annotations, representing an expansion of 30 percent over the second edition. The appendix lists 116 basic or core reference…

  10. A Reference Grammar of Spoken Kannada.

    ERIC Educational Resources Information Center

    Schiffman, Harold

    This reference grammar is a description of the speech of educated people of the Bangalore/Mysore area of Karnataka State in South India. This particular dialect is used in films and, to some extent, on the radio. The four sections of the book deal with: (1) phonology, (2) the noun phrase, (3) the verb phrase, and (4) syntax. Each item that is…

  11. 32 CFR 2103.1 - References.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 32 National Defense 6 2011-07-01 2011-07-01 false References. 2103.1 Section 2103.1 National Defense Other Regulations Relating to National Defense NATIONAL SECURITY COUNCIL REGULATIONS TO IMPLEMENT E.O. 12065-INCLUDING PROCEDURES FOR PUBLIC ACCESS TO DOCUMENTS THAT MAY BE DECLASSIFIED...

  12. Selected Reference Books of 1991-92.

    ERIC Educational Resources Information Center

    McIlvaine, Eileen

    1992-01-01

    Reviews 20 selected reference works published in 1991 and 1992 with purchasing recommendations for academic libraries. Titles are grouped under the following headings: National Bibliographies, Abbreviations, Librarianship, Religion, Mythology, Literature, Music, Art and Architecture, Popular Culture, Women's Studies, Area Studies, and Health…

  13. Sociology: A Guide to Reference Sources.

    ERIC Educational Resources Information Center

    Giffin, Meredith

    Sociology, the study of the organization and activities of human societies, encompasses many fields of inquiry and consequently the literature of the discipline is vast. In providing access to some of this literature, this guide concentrates on reference sources which may be found in McLennan Library of McGill University, Montreal, Canada. Areas…

  14. Anthropology: A Student's Guide to Reference Sources.

    ERIC Educational Resources Information Center

    Slavin, Suzy M., Comp.

    The guide identifies approximately 100 anthropology source materials in the reference department of McLennan Library at McGill University. It was designd to help students doing anthropological research and to illustrate the variety of materials on social and cultural anthropology in the McLennan Library. Physical anthropolgy, linguistics, and…

  15. Standard Albanian. A Reference Grammar for Students.

    ERIC Educational Resources Information Center

    Newmark, Leonard; And Others

    This book is intended as a reference grammar for English-speaking students of present-day Albanian. The introductory chapter provides information on the country and its people, the Albanian language and dialects, phonology, and morphology. The other chapters contain grammatical explanations in English and examples. (AMH)

  16. Electronic Reference Library: Silverplatter's Database Networking Solution.

    ERIC Educational Resources Information Center

    Millea, Megan

    Silverplatter's Electronic Reference Library (ERL) provides wide area network access to its databases using TCP/IP communications and client-server architecture. ERL has two main components: The ERL clients (retrieval interface) and the ERL server (search engines). ERL clients provide patrons with seamless access to multiple databases on multiple…

  17. Building Complex Reference Objects from Dual Sets

    ERIC Educational Resources Information Center

    Patson, Nikole D.; Warren, Tessa

    2011-01-01

    There has been considerable psycholinguistic investigation into the conditions that allow separately introduced individuals to be joined into a plural set and represented as a complex reference object (e.g., Eschenbach et al., 1989; Garrod & Sanford, 1982; Koh & Clifton, 2002; Koh et al., 2008; Moxey, Sanford, Sturt, & Morrow, 2004; Sanford &…

  18. 78 FR 69006 - Incorporation by Reference

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-11-18

    ... the Code of Federal Regulations (77 FR 11414 (February 27, 2012)). Given the recent government... correcting the docket number and adding a link to the docket. Correction In proposed rule FR Doc. 2013-24217...; ] OFFICE OF THE FEDERAL REGISTER 1 CFR Part 51 RIN 3095-AB78 Incorporation by Reference AGENCY: Office...

  19. The Evolution of the Reference Librarian

    ERIC Educational Resources Information Center

    Johnson, Wendell G.

    2011-01-01

    The job of the contemporary reference librarian has a virtual component unimaginable a generation ago. Today's library professional can obtain an MLS (or equivalent) online with a minimal residency requirement. Not only the degree, but also library sources, and indeed patrons, have become virtual. Both books and periodicals can be consulted by…

  20. Magnifying Devices: A Resource Guide. Reference Circular.

    ERIC Educational Resources Information Center

    Strauss, Carol, Comp.

    The devices listed in this reference circular are designed to assist people who have visual impairments by magnifying objects and print or graphic materials. Before buying a magnification device, one should consult a low-vision specialist to determine the level of usable vision, the power of magnification needed for a particular eye condition and…