Science.gov

Sample records for brown coal combustion

  1. Pyrolysis of Compositions of Mixtures of Combustible Shales and Brown Coals Deposited in Belarus

    NASA Astrophysics Data System (ADS)

    Lishtvan, I. I.; Dudarchik, V. M.; Kraiko, V. M.; Belova, Yu. V.

    2013-11-01

    This paper presents the results of investigating the pyrolysis of compositions of mixtures of brown coals and combustible shales in a close-packed and a moving layer and the yield dynamics of the pyrolysis gas and resin. A comparative analysis of the quality of pyrolysis products obtained from combustible shales and brown coal and from their mixtures has been performed.

  2. Sulfur emission from Victorian brown coal under pyrolysis, oxy-fuel combustion and gasification conditions.

    PubMed

    Chen, Luguang; Bhattacharya, Sankar

    2013-02-01

    Sulfur emission from a Victorian brown coal was quantitatively determined through controlled experiments in a continuously fed drop-tube furnace under three different atmospheres: pyrolysis, oxy-fuel combustion, and carbon dioxide gasification conditions. The species measured were H(2)S, SO(2), COS, CS(2), and more importantly SO(3). The temperature (873-1273 K) and gas environment effects on the sulfur species emission were investigated. The effect of residence time on the emission of those species was also assessed under oxy-fuel condition. The emission of the sulfur species depended on the reaction environment. H(2)S, SO(2), and CS(2) are the major species during pyrolysis, oxy-fuel, and gasification. Up to 10% of coal sulfur was found to be converted to SO(3) under oxy-fuel combustion, whereas SO(3) was undetectable during pyrolysis and gasification. The trend of the experimental results was qualitatively matched by thermodynamic predictions. The residence time had little effect on the release of those species. The release of sulfur oxides, in particular both SO(2) and SO(3), is considerably high during oxy-fuel combustion even though the sulfur content in Morwell coal is only 0.80%. Therefore, for Morwell coal utilization during oxy-fuel combustion, additional sulfur removal, or polishing systems will be required in order to avoid corrosion in the boiler and in the CO(2) separation units of the CO(2) capture systems. PMID:23301852

  3. Nitrogen oxides, sulfur trioxide, and mercury emissions during oxy-fuel fluidized bed combustion of Victorian brown coal.

    PubMed

    Roy, Bithi; Chen, Luguang; Bhattacharya, Sankar

    2014-12-16

    This study investigates, for the first time, the NOx, N2O, SO3, and Hg emissions from combustion of a Victorian brown coal in a 10 kWth fluidized bed unit under oxy-fuel combustion conditions. Compared to air combustion, lower NOx emissions and higher N2O formation were observed in the oxy-fuel atmosphere. These NOx reduction and N2O formations were further enhanced with steam in the combustion environment. The NOx concentration level in the flue gas was within the permissible limit in coal-fired power plants in Victoria. Therefore, an additional NOx removal system will not be required using this coal. In contrast, both SO3 and gaseous mercury concentrations were considerably higher under oxy-fuel combustion compared to that in the air combustion. Around 83% of total gaseous mercury released was Hg(0), with the rest emitted as Hg(2+). Therefore, to control harmful Hg(0), a mercury removal system may need to be considered to avoid corrosion in the boiler and CO2 separation units during the oxy-fuel fluidized-bed combustion using this coal. PMID:25402169

  4. Coal combustion science

    SciTech Connect

    Hardesty, D.R.; Baxter, L.L.; Fletcher, T.H.; Mitchell, R.E.

    1990-11-01

    The objective of this activity is to support the Office of Fossil Energy in executing research on coal combustion science. This activity consists of basic research on coal combustion that supports both the Pittsburgh Energy Technology Center (PETC) Direct Utilization Advanced Research and Technology Development Program, and the International Energy Agency (IEA) Coal Combustion Science Project. Specific tasks include: coal devolatilization, coal char combustion, and fate of mineral matter during coal combustion. 91 refs., 40 figs., 9 tabs.

  5. Coal combustion products

    USGS Publications Warehouse

    Kalyoncu, R.S.; Olson, D.W.

    2001-01-01

    Coal-burning powerplants, which supply more than half of U.S. electricity, also generate coal combustion products, which can be both a resource and a disposal problem. The U.S. Geological Survey collaborates with the American Coal Ash Association in preparing its annual report on coal combustion products. This Fact Sheet answers questions about present and potential uses of coal combustion products.

  6. Modeling of pulverized coal combustion processes in a vortex furnace of improved design. Part 2: Combustion of brown coal from the Kansk-Achinsk Basin in a vortex furnace

    NASA Astrophysics Data System (ADS)

    Krasinsky, D. V.; Salomatov, V. V.; Anufriev, I. S.; Sharypov, O. V.; Shadrin, E. Yu.; Anikin, Yu. A.

    2015-03-01

    This paper continues with the description of study results for an improved-design steam boiler vortex furnace, for the full-scale configuration of which the numerical modeling of a three-dimensional turbulent two-phase reacting flow has been performed with allowance for all the principal heat and mass transfer processes in the torch combustion of pulverized Berezovsk brown coal from the Kansk-Achinsk Basin. The detailed distributions of velocity, temperature, concentration, and heat flux fields in different cross sections of the improved vortex furnace have been obtained. The principal thermoengineering and environmental characteristics of this furnace are given.

  7. Coal Combustion Science

    SciTech Connect

    Hardesty, D.R.; Fletcher, T.H.; Hurt, R.H.; Baxter, L.L. )

    1991-08-01

    The objective of this activity is to support the Office of Fossil Energy in executing research on coal combustion science. This activity consists of basic research on coal combustion that supports both the Pittsburgh Energy Technology Center Direct Utilization Advanced Research and Technology Development Program, and the International Energy Agency Coal Combustion Science Project. Specific tasks for this activity include: (1) coal devolatilization - the objective of this risk is to characterize the physical and chemical processes that constitute the early devolatilization phase of coal combustion as a function of coal type, heating rate, particle size and temperature, and gas phase temperature and oxidizer concentration; (2) coal char combustion -the objective of this task is to characterize the physical and chemical processes involved during coal char combustion as a function of coal type, particle size and temperature, and gas phase temperature and oxygen concentration; (3) fate of mineral matter during coal combustion - the objective of this task is to establish a quantitative understanding of the mechanisms and rates of transformation, fragmentation, and deposition of mineral matter in coal combustion environments as a function of coal type, particle size and temperature, the initial forms and distribution of mineral species in the unreacted coal, and the local gas temperature and composition.

  8. Full scale measurements to validate mathematical models and to monitor the combustion behavior of bituminous and brown coal-fired boilers

    SciTech Connect

    Maier, J.; Kluger, F.; Heinzel, T.; Spliethoff, H.; Hein, K.R.G.

    1999-07-01

    In recent years, the Institute for Process Engineering and Power Plant Technology (IVD) carried out measurement campaigns on three full-scale-bituminous- and brown-coal-fired boilers between 80 and 500 MW{sub el}. One boiler was designed as a boxer firing system, configured with swirl burner, and the other two were tangentially fired with jet burner. Aim of the measurement campaigns was to evaluate the suitability of bituminous- and brown-coal-fired boilers (500 and 320 MW {sub el}) for alternative coals and their blends. To monitor changes in the combustion and emission behavior, suction probes to measure flue gas concentrations and temperatures along the furnace were inserted. Shifts in heat transfer between the radiative and convective part of the boiler were correlated with the kind of coal, the injected water mass flow in the superheater steam and the flue gas temperature. Also changes with the unburned carbon and of the NO{sub x}, SO{sub 2} and CO emission behavior were measured and correlated with coal types and their variable share. The second objective of the measurement campaigns in the bituminous-coal-fired boilers (500 MW{sub el} and 80 MW{sub el}) was the acquisition of combustion data to validate the mathematical combustion model AIOLOS, which has been successfully developed by the IVD during the last ten years. For this purpose flue-gas-concentration and temperature measurements have been carried out at IVD in the near burner zone and in front of the superheaters. Furthermore, the suitability of 3-color pyrometry, thermocouples and acoustic temperature measurement systems will be compared and discussed in this paper.

  9. Environmentally conscious coal combustion

    SciTech Connect

    Hickmott, D.D.; Brown, L.F.; Currier, R.P.

    1997-08-01

    This is the final report of a one-year, Laboratory-Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). The objective of this project was to evaluate the environmental impacts of home-scale coal combustion on the Navajo Reservation and develop strategies to reduce adverse health effects associated with home-scale coal combustion. Principal accomplishments of this project were: (1) determination of the metal and gaseous emissions of a representative stove on the Navajo Reservation; (2) recognition of cyclic gaseous emissions in combustion in home-scale combustors; (3) `back of the envelope` calculation that home-scale coal combustion may impact Navajo health; and (4) identification that improved coal stoves require the ability to burn diverse feedstocks (coal, wood, biomass). Ultimately the results of Navajo home-scale coal combustion studies will be extended to the Developing World, particularly China, where a significant number (> 150 million) of households continue to heat their homes with low-grade coal.

  10. Coal combustion system

    DOEpatents

    Wilkes, Colin; Mongia, Hukam C.; Tramm, Peter C.

    1988-01-01

    In a coal combustion system suitable for a gas turbine engine, pulverized coal is transported to a rich zone combustor and burned at an equivalence ratio exceeding 1 at a temperature above the slagging temperature of the coal so that combustible hot gas and molten slag issue from the rich zone combustor. A coolant screen of water stretches across a throat of a quench stage and cools the combustible gas and molten slag to below the slagging temperature of the coal so that the slag freezes and shatters into small pellets. The pelletized slag is separated from the combustible gas in a first inertia separator. Residual ash is separated from the combustible gas in a second inertia separator. The combustible gas is mixed with secondary air in a lean zone combustor and burned at an equivalence ratio of less than 1 to produce hot gas motive at temperature above the coal slagging temperature. The motive fluid is cooled in a dilution stage to an acceptable turbine inlet temperature before being transported to the turbine.

  11. Coal combustion research

    SciTech Connect

    Daw, C.S.

    1996-06-01

    This section describes research and development related to coal combustion being performed for the Fossil Energy Program under the direction of the Morgantown Energy Technology Center. The key activity involves the application of chaos theory for the diagnosis and control of fossil energy processes.

  12. Brown coal preparation machines

    SciTech Connect

    Bleckmann, H.; Sitte, W.; Kellerwessel, H.

    1981-05-01

    Lignite usually requires comminuting and screening before being used as a fuel in power plants. Reduction machines normally used for coarse crushing bituminous coal, such as jaw crushers, roll crushers, and impact crushers, are not generally suitable for lignite as they require a brittle feed and large grain size. In contrast to these requirements, lignite can be easily compressed and has a small grain size. Therefore, special crusher types have been developed for the coarse reduction of lignite. These machines resemble roll crushers but subject the feed to shearing and tearing forces rather than to compressive stress. It is often necessary to screen the lignite to remove the undersize or to limit the maximum particle size before the next comminution process. Screening the lignite is a particularly difficult operation due to the high water content and the presence of clay minerals which tend to clog the screening machines. These problems can be overcome with multi-roll sizers.

  13. COMBUSTION OF HYDROTHERMALLY TREATED COALS

    EPA Science Inventory

    The report gives results of an evaluation of: (1) the relationship of the combustion characteristics of hydrothermally treated (HTT) coals to environmental emissions, boiler design, and interchangeability of solid fuels produced by the Hydrothermal Coal Process (HCP) with raw coa...

  14. Coal char fragmentation during pulverized coal combustion

    SciTech Connect

    Baxter, L.L.

    1995-07-01

    A series of investigations of coal and char fragmentation during pulverized coal combustion is reported for a suite of coals ranging in rank from lignite to low-volatile (lv) bituminous coal under combustion conditions similar to those found in commercial-scale boilers. Experimental measurements are described that utilize identical particle sizing characteristics to determine initial and final size distributions. Mechanistic interpretation of the data suggest that coal fragmentation is an insignificant event and that char fragmentation is controlled by char structure. Chars forming cenospheres fragment more extensively than solid chars. Among the chars that fragment, large particles produce more fine material than small particles. In all cases, coal and char fragmentation are seen to be sufficiently minor as to be relatively insignificant factors influencing fly ash size distribution, particle loading, and char burnout.

  15. Ukrainian mineral wax from brown coal

    SciTech Connect

    Shabad, T.

    1986-07-01

    An unusual mineral enterprise is the mineral wax plant of Semenovskoye in the Aleksandriya brown coal basin of the Ukraine. The only plant of its kind in the Soviet Union, it has been in operation since 1959, extracting mineral wax from the local bitumen-rich brown coal. The plant yields about 7.5 tons of mineral wax a day (about 2700 tons a year), for use in a variety of applications.

  16. Catalyzing the Combustion of Coal

    NASA Technical Reports Server (NTRS)

    Humphrey, M. F.; Dokko, W.

    1982-01-01

    Reaction rate of coal in air can be increased by contacting or coating coal with compound such as calcium acetate. The enhanced reaction rate generates more heat, reducing furnace size. Increase in combustion rate is about 26 percent, and internal pollutants in powerplant are reduced.

  17. Enhancement of pulverized coal combustion by plasma technology

    SciTech Connect

    Gorokhovski, M.A.; Jankoski, Z.; Lockwood, F.C.; Karpenko, E.I.; Messerle, V.E.; Ustimenko, A.B.

    2007-07-01

    Plasma-assisted pulverized coal combustion is a promising technology for thermal power plants (TPP). This article reports one- and three- dimensional numerical simulations, as well as laboratory and industrial measurements of coal combustion using a plasma-fuel system (PFS). The chemical kinetic and fluid mechanics involved in this technology are analysed. The results show that a PFS, can be used to promote early ignition and enhanced stabilization of a pulverized coal flame. It is shown that this technology, in addition to enhancing the combustion efficiency of the flame, reduces harmful emissions from power coals of all ranks (brown, bituminous, anthracite and their mixtures). Data summarising the experience of 27 pulverized coal boilers in 16 thermal power plants in several countries (Russia, Kazakhstan, Korea, Ukraine, Slovakia, Mongolia and China), embracing steam productivities from 75 to 670 tons per hour (TPH), are presented. Finally, the practical computation of the characteristics of the PFS, as function of coal properties, is discussed.

  18. Fluidized bed combustion of coal

    NASA Astrophysics Data System (ADS)

    Tatebayashi, J.; Okada, Y.; Yano, K.; Takada, T.; Handa, K.

    The effect of various parameters on combustion efficiency, desulfurization efficiency and NO emission in fluidized bed combustion of coal were investigated by using two test combustors whose sectional areas were 200 mm and 500 mm square. It has been revealed that by employing two-stage combustion and setting the primary air ratio, secondary air injection height and other parameters to optimum levels, NO emission can be greatly reduced while barely impairing combustion efficiency or desulfurization efficiency. Also, NO emission of less than 50 ppm and desulfurization efficiency of as high as 93% were achieved. These results have ensured good prospects for the development of a coal combustion boiler system which can satisfy the strictest environmental protection regulations, without installing special desulfurization and de-NO(X) facilities.

  19. Fuel briquettes from brown coals of Yakutia

    SciTech Connect

    L.A. Nikolaeva; V.G. Latyshev; O.N. Burenina

    2009-04-15

    Experimental data on the development of technology for the manufacture of briquetted fuel from brown coals with the use of various petroleum binders are presented. The influence of the moisture content, the coal particle-size composition, the binder type and concentration, the compacting pressure, and heat treatment regimes on the mechanical properties of the materials was studied. The optimal compositions and optimal values of the engineering parameters for the production of graded briquetted fuel from brown coals of the Kangalassy deposit in the Republic of Sakha (Yakutia) were established.

  20. Oxy-coal Combustion Studies

    SciTech Connect

    Wendt, J.; Eddings, E.; Lighty, J.; Ring, T.; Smith, P.; Thornock, J.; Y Jia, W. Morris; Pedel, J.; Rezeai, D.; Wang, L.; Zhang, J.; Kelly, K.

    2012-01-06

    The objective of this project is to move toward the development of a predictive capability with quantified uncertainty bounds for pilot-scale, single-burner, oxy-coal operation. This validation research brings together multi-scale experimental measurements and computer simulations. The combination of simulation development and validation experiments is designed to lead to predictive tools for the performance of existing air fired pulverized coal boilers that have been retrofitted to various oxy-firing configurations. In addition, this report also describes novel research results related to oxy-combustion in circulating fluidized beds. For pulverized coal combustion configurations, particular attention is focused on the effect of oxy-firing on ignition and coal-flame stability, and on the subsequent partitioning mechanisms of the ash aerosol.

  1. Nitrogen release during coal combustion

    SciTech Connect

    Baxter, L.L.; Mitchell, R.E.; Fletcher, T.H.; Hurt, R.H.

    1995-02-01

    Experiments in entrained flow reactors at combustion temperatures are performed to resolve the rank dependence of nitrogen release on an elemental basis for a suite of 15 U.S. coals ranging from lignite to low-volatile bituminous. Data were obtained as a function of particle conversion, with overall mass loss up to 99% on a dry, ash-free basis. Nitrogen release rates are presented relative to both carbon loss and overall mass loss. During devolatilization, fractional nitrogen release from low-rank coals is much slower than fractional mass release and noticeably slower than fractional carbon release. As coal rank increases, fractional nitrogen release rate relative to that of carbon and mass increases, with fractional nitrogen release rates exceeding fractional mass and fractional carbon release rates during devolatilization for high-rank (low-volatile bituminous) coals. At the onset of combustion, nitrogen release rates increase significantly. For all coals investigated, cumulative fractional nitrogen loss rates relative to those of mass and carbon passes through a maximum during the earliest stages of oxidation. The mechanism for generating this maximum is postulated to involve nascent thermal rupture of nitrogen-containing compounds and possible preferential oxidation of nitrogen sites. During later stages of oxidation, the cumulative fractional loss of nitrogen approaches that of carbon for all coals. Changes in the relative release rates of nitrogen compared to those of both overall mass and carbon during all stages of combustion are attributed to a combination of the chemical structure of coals, temperature histories during combustion, and char chemistry.

  2. Coal combustion by wet oxidation

    SciTech Connect

    Bettinger, J.A.; Lamparter, R.A.; McDowell, D.C.

    1980-11-15

    The combustion of coal by wet oxidation was studied by the Center for Waste Management Programs, of Michigan Technological University. In wet oxidation a combustible material, such as coal, is reacted with oxygen in the presence of liquid water. The reaction is typically carried out in the range of 204/sup 0/C (400/sup 0/F) to 353/sup 0/C (650/sup 0/F) with sufficient pressure to maintain the water present in the liquid state, and provide the partial pressure of oxygen in the gas phase necessary to carry out the reaction. Experimental studies to explore the key reaction parameters of temperature, time, oxidant, catalyst, coal type, and mesh size were conducted by running batch tests in a one-gallon stirred autoclave. The factors exhibiting the greatest effect on the extent of reaction were temperature and residence time. The effect of temperature was studied from 204/sup 0/C (400/sup 0/F) to 260/sup 0/C (500/sup 0/F) with a residence time from 600 to 3600 seconds. From this data, the reaction activation energy of 2.7 x 10/sup 4/ calories per mole was determined for a high-volatile-A-Bituminous type coal. The reaction rate constant may be determined at any temperature from the activation energy using the Arrhenius equation. Additional data were generated on the effect of mesh size and different coal types. A sample of peat was also tested. Two catalysts were evaluated, and their effects on reaction rate presented in the report. In addition to the high temperature combustion, low temperature desulfurization is discussed. Desulfurization can improve low grade coal to be used in conventional combustion methods. It was found that 90% of the sulfur can be removed from the coal by wet oxidation with the carbon untouched. Further desulfurization studies are indicated.

  3. Oxy Coal Combustion at the US EPA

    EPA Science Inventory

    Oxygen enriched coal (oxy-coal) combustion is a developing, and potentially a strategically key technology intended to accommodate direct CO2 recovery and sequestration. Oxy-coal combustion is also intended for retrofit application to existing power plants. During oxy-coal comb...

  4. Reduction of spontaneous combustion of coal

    SciTech Connect

    Burns, E.J.

    1982-05-25

    A composition for the prevention of spontaneous combustion of coal is described which is comprised of at least about 2 percent of polyethylene oxide and the balance water. Also described is a method for reducing the spontaneous combustion tendency of coal by contacting coal with the above composition and then drying the coal.

  5. 40 CFR 721.10532 - Tar, brown coal.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Tar, brown coal. 721.10532 Section 721... Tar, brown coal. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as tar, brown coal (PMN P-12-167, CAS No. 101316-83-0) is subject...

  6. 40 CFR 721.10532 - Tar, brown coal.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Tar, brown coal. 721.10532 Section 721... Tar, brown coal. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as tar, brown coal (PMN P-12-167, CAS No. 101316-83-0) is subject...

  7. TOXIC SUBSTANCES FROM COAL COMBUSTION

    SciTech Connect

    A KOLKER; AF SAROFIM; CL SENIOR; FE HUGGINS; GP HUFFMAN; I OLMEZ; J LIGHTY; JOL WENDT; JOSEPH J HELBLE; MR AMES; N YAP; R FINKELMAN; T PANAGIOTOU; W SEAMES

    1998-12-08

    The Clean Air Act Amendments of 1990 identify a number of hazardous air pollutants (HAPs) as candidates for regulation. Should regulations be imposed on HAP emissions from coal-fired power plants, a sound understanding of the fundamental principles controlling the formation and partitioning of toxic species during coal combustion will be needed. With support from the Federal Energy Technology Center (FETC), the Electric Power Research Institute, the Lignite Research Council, and VTT (Finland), Physical Sciences Inc. (PSI) has teamed with researchers from USGS, MIT, the University of Arizona (UA), the University of Kentucky (UK), the University of Connecticut (UC), the University of Utah (UU) and the University of North Dakota Energy and Environmental Research Center (EERC) to develop a broadly applicable emissions model useful to regulators and utility planners. The new Toxics Partitioning Engineering Model (ToPEM) will be applicable to all combustion conditions including new fuels and coal blends, low-NO combustion systems, and new power generation x plants. Development of ToPEM will be based on PSI's existing Engineering Model for Ash Formation (EMAF). This report covers the reporting period from 1 July 1998 through 30 September 1998. During this period distribution of all three Phase II coals was completed. Standard analyses for the whole coal samples were also completed. Mössbauer analysis of all project coals and fractions received to date has been completed in order to obtain details of the iron mineralogy. The analyses of arsenic XAFS data for two of the project coals and for some high arsenic coals have been completed. Duplicate splits of the Ohio 5,6,7 and North Dakota lignite samples were taken through all four steps of the selective leaching procedure. Leaching analysis of the Wyodak coal has recently commenced. Preparation of polished coal/epoxy pellets for probe/SEM studies is underway. Some exploratory mercury LIII XAFS work was carried

  8. The briquetting of Victorian brown coals

    SciTech Connect

    Perry, G.J.; Allardice, D.J.; Bates, A.J.; Hutchinson, J.C.

    1994-12-31

    This paper describes the experience gained in 70 years of binderless briquetting of Victorian brown coals. The processing stages of crushing, drying, cooling, pressing, and shipping are described in detail, as are the key process parameters. The product is used for industrial and household fuel, for export, and for production of further upgraded products such as absorbent chars, metallurgical reductants, and smokeless cooking fuels.

  9. Fluidized bed coal combustion reactor

    NASA Technical Reports Server (NTRS)

    Moynihan, P. I.; Young, D. L. (Inventor)

    1981-01-01

    A fluidized bed coal reactor includes a combination nozzle-injector ash-removal unit formed by a grid of closely spaced open channels, each containing a worm screw conveyor, which function as continuous ash removal troughs. A pressurized air-coal mixture is introduced below the unit and is injected through the elongated nozzles formed by the spaces between the channels. The ash build-up in the troughs protects the worm screw conveyors as does the cooling action of the injected mixture. The ash layer and the pressure from the injectors support a fluidized flame combustion zone above the grid which heats water in boiler tubes disposed within and/or above the combustion zone and/or within the walls of the reactor.

  10. Fluidized bed coal combustion reactor

    SciTech Connect

    Moynihan, P.I.; Young, D.L.

    1981-09-01

    A fluidized bed coal reactor includes a combination nozzle-injector ash-removal unit formed by a grid of closely spaced open channels, each containing a worm screw conveyor, which function as continuous ash removal troughs. A pressurized air-coal mixture is introduced below the unit and is injected through the elongated nozzles formed by the spaces between the channels. The ash build-up in the troughs protects the worm screw conveyors as does the cooling action of the injected mixture. The ash layer and the pressure from the injectors support a fluidized flame combustion zone above the grid which heats water in boiler tubes disposed within and/or above the combustion zone and/or within the walls of the reactor. Official Gazette of the U.S. Patent and Trademark Office

  11. TOXIC SUBSTANCES FROM COAL COMBUSTION

    SciTech Connect

    Kolker, A.; Sarofim, A.F.; Palmer, C.A.; Huggins, F.E.; Huffman, G.P.; Lighty, J.; Veranth, J.; Helble, J.J.; Wendt, J.O.L.; Ames, M.R.; Finkelman, R.; Mamani-Paco, M.; Sterling, R.; Mroczkowsky, S.J.; Panagiotou, T.; Seames, W.

    1999-05-10

    The Clean Air Act Amendments of 1990 identify a number of hazardous air pollutants (HAPs) as candidates for regulation. Should regulations be imposed on HAP emissions from coal-fired power plants, a sound understanding of the fundamental principles controlling the formation and partitioning of toxic species during coal combustion will be needed. With support from the Federal Energy Technology Center (FETC), the Electric Power Research Institute, and VTT (Finland), Physical Sciences Inc. (PSI) has teamed with researchers from USGS, MIT, the University of Arizona (UA), the University of Kentucky (UK), the University of Connecticut (UC), the University of Utah (UU) and the University of North Dakota Energy and Environ-mental Research Center (EERC) to develop a broadly applicable emissions model useful to regulators and utility planners. The new Toxics Partitioning Engineering Model (ToPEM) will be applicable to all combustion conditions including new fuels and coal blends, low-NOx combustion systems, and new power generation plants. Development of ToPEM will be based on PSI's existing Engineering Model for Ash Formation (EMAF). This report covers the reporting period from 1 January 1999 to 31 March 1999. During this period, a full Program Review Meeting was held at the University of Arizona. At this meeting, the progress of each group was reviewed, plans for the following 9 month period were discussed, and action items (principally associated with the transfer of samples and reports among the various investigators) were identified.

  12. Method of pyrolyzing brown coal

    SciTech Connect

    Michel, W.; Heberlein, I.; Ossowski, M.; Paul, H.; Rummel, A.; Seher, G.

    1985-08-06

    A two-step method and apparatus are disclosed based on the fluidized bed principle, for the production of coke, rich gas and pyrolysis tar, with the object of executing the method in a compact apparatus arrangement, with high energy efficiency and high throughput capacity. This is accomplished by a sequence in which the fine grains removed from the drying vapor mixture are removed from the actual pyrolysis process, and a hot gas, alien to the carbonization, is used as fluidization medium in the pyrolysis reactor, and with a hot gas-high performance separator being used for the dust separation from the pyrolysis gas, with the combustion exhaust gas produced in the combustion chamber being used for the indirect heating of the fluidization medium, for the pre-heating of the gas, which is alien to the carbonization, and for the direct heating in the dryer. The dryer has a double casing in the area of the fluidized bed, and a mixing chamber is arranged directly underneath its initial flow bottom, while the pyrolysis reactor is directly connected to the combustion chamber and the pre-heater.

  13. Component composition of deresined brown coal wax

    SciTech Connect

    L.P. Noskova

    2008-10-15

    The products of the alkaline hydrolysis of wax isolated from brown coal from the Sergeevskoe deposit were studied using chromatography and IR and NMR spectroscopy. It was found that hydrocarbons, alcohols, acids, and a representative fraction of unsaponifiable esters were the constituents of wax. High-molecular-weight fatty alcohols and acids were identified as the constituents of wax with the use of thin-layer chromatography.

  14. TECHNOLOGIES FOR CONTROLLING POLLUTANTS FROM COAL COMBUSTION

    EPA Science Inventory

    The paper is an overview of EPA's efforts in developing technology for controlling pollutants from coal combustion. SO2, NOx, and particles are the predominant pollutants emitted from the combustion of coal. One goal of current EPA research and development is to reduce the costs ...

  15. Electrochemical protection of coal from spontaneous combustion

    SciTech Connect

    Aleksandrov, I.V.; Burkov, P.A.; Kamneva, A.I.; Khokhlov, Yu.I.

    1984-01-01

    An electrochemical method is described for the protection of coal stocks from self-heating and spontaneous combustion. Cathodic polarisation is effected by an external source of direct current using contact electrodes situated in the coal. Practically complete suppression of self-heating is claimed for 450-500 m/sup 3/ volumes of coal at an insignificant energy cost.

  16. Influence of additives on the increase of the heating value of Bayah's coal with upgrading brown coal (UBC) method

    NASA Astrophysics Data System (ADS)

    Heriyanto, Heri; Widya Ernayati, K.; Umam, Chairul; Margareta, Nita

    2015-12-01

    UBC (upgrading brown coal) is a method of improving the quality of coal by using oil as an additive. Through processing in the oil media, not just the calories that increase, but there is also water repellent properties and a decrease in the tendency of spontaneous combustion of coal products produced. The results showed a decrease in the water levels of natural coal bayah reached 69%, increase in calorific value reached 21.2%. Increased caloric value and reduced water content caused by the water molecules on replacing seal the pores of coal by oil and atoms C on the oil that is bound to increase the percentage of coal carbon. As a result of this experiment is, the produced coal has better calorific value, the increasing of this new calorific value up to 23.8% with the additive waste lubricant, and the moisture content reduced up to 69.45%.

  17. Leachability of trace elements in coal and coal combustion wastes

    SciTech Connect

    Rice, C.A.; Breit, G.N.; Fishman, N.S.; Bullock, J.H. Jr.

    1999-07-01

    Leaching of trace elements from coal and coal combustion waste (CCW) products from a coal-fired power plant, burning coal from the Appalachian and Illinois basins, was studied using deionized (DI) water as a lixiviant to resemble natural conditions in waste disposal sites exposed to dilute meteoric water infiltration. Samples of bottom ash, fly ash, and feed coal were collected from two combustion units at monthly intervals, along with a bulk sample of wastes deposited in an on-site disposal pond. The units burn different coals, one a high-sulfur coal (2.65 to 3.5 weight percent S) and the other, a low-sulfur coal (0.6--0.9 eight percent S). Short-term batch leaches with DI water were performed for times varying from a few minutes to 18 hours. Select fly ash samples were also placed in long-term (> 1 year) flow-through columns.

  18. Coal Combustion Science quarterly progress report, April--June 1990

    SciTech Connect

    Hardesty, D.R.; Baxter, L.L.; Fletcher, T.H.; Mitchell, R.E.

    1990-11-01

    This document provides a quarterly status report of the Coal Combustion Science Program that is being conducted at the Combustion, Research Facility, Sandia National Laboratories, Livermore, California. Coal devolatilization, coal char combustion, and fate of mineral matter during coal combustion. 56 refs., 25 figs., 13 tabs.

  19. The effect of upgrading processes on combustion characteristics of Berau coal

    SciTech Connect

    Datin Fatia Umar; Binarko Santoso; Hiromoto Usui

    2007-12-15

    Indonesian coal was upgraded by upgraded brown coal (UBC), hot water drying (HWD), and steam drying (SD) processes to study the combustion characteristics of this coal. The differential thermal-thermogravimetric analysis (DTA-TG) was carried out to obtain some combustion parameters, such as, ignition temperature (T{sub ig}), maximum combustion rate temperature (T{sub max}), maximum combustion rate (R{sub max}), char burn-out temperature (T{sub bo}), and ash yield. The differential thermal analyzer (DTA) curve can be used to estimate the heat released during the combustion process, which corresponds to the high heating value of the coal. The results show that the combustion characteristics of HWD and SD processes are much better than those of the UBC process. This is because the UBC process was conducted at lower temperature and pressure. 11 refs., 2 figs., 3 tabs.

  20. SPONTANEOUS COAL COMBUSTION; MECHANISMS AND PREDICTION.

    USGS Publications Warehouse

    Herring, James R.; Rich, Fredrick J.

    1983-01-01

    Spontaneous ignition and combustion of coal is a major problem to the coal mining, shipping, and use industries; unintentional combustion causes loss of the resource as well as jeopardy to life and property. The hazard to life is especially acute in the case of underground coal mine fires that start by spontaneous ignition. It is the intention of this research to examine previously suggested causes of spontaneous ignition, to consider new evidence, and to suggest an experimental approach to determine which of these suggested causes is relevant to western U. S. coal. This discussion focuses only on causes and mechanism of spontaneous ignition.

  1. COSTS FOR ADVANCED COAL COMBUSTION TECHNOLOGIES

    EPA Science Inventory

    The report gives results of an evaluation of the development status of advanced coal combustion technologies and discusses the preparation of performance and economic models for their application to electric utility plants. he technologies addressed were atmospheric fluidized bed...

  2. Combustion of Coal/Oil/Water Slurries

    NASA Technical Reports Server (NTRS)

    Kushida, R. O.

    1982-01-01

    Proposed test setup would measure combustion performance of new fuels by rapidly heating a droplet of coal/oil/water mixture and recording resulting explosion. Such mixtures are being considered as petroleum substitutes in oil-fired furnaces.

  3. Rheological properties of water-coal slurries based on brown coal in the presence of sodium lignosulfonates and alkali

    SciTech Connect

    D.P. Savitskii; A.S. Makarov; V.A. Zavgorodnii

    2009-07-01

    The effect of the oxidized surface of brown coal on the structural and rheological properties of water-coal slurries was found. The kinetics of structure formation processes in water-coal slurries based on as-received and oxidized brown coal was studied. The effect of lignosulfonate and alkali additives on the samples of brown coal was considered.

  4. Coal Combustion Products Extension Program

    SciTech Connect

    Tarunjit S. Butalia; William E. Wolfe

    2006-01-11

    This final project report presents the activities and accomplishments of the ''Coal Combustion Products Extension Program'' conducted at The Ohio State University from August 1, 2000 to June 30, 2005 to advance the beneficial uses of coal combustion products (CCPs) in highway and construction, mine reclamation, agricultural, and manufacturing sectors. The objective of this technology transfer/research program at The Ohio State University was to promote the increased use of Ohio CCPs (fly ash, FGD material, bottom ash, and boiler slag) in applications that are technically sound, environmentally benign, and commercially competitive. The project objective was accomplished by housing the CCP Extension Program within The Ohio State University College of Engineering with support from the university Extension Service and The Ohio State University Research Foundation. Dr. Tarunjit S. Butalia, an internationally reputed CCP expert and registered professional engineer, was the program coordinator. The program coordinator acted as liaison among CCP stakeholders in the state, produced information sheets, provided expertise in the field to those who desired it, sponsored and co-sponsored seminars, meetings, and speaking at these events, and generally worked to promote knowledge about the productive and proper application of CCPs as useful raw materials. The major accomplishments of the program were: (1) Increase in FGD material utilization rate from 8% in 1997 to more than 20% in 2005, and an increase in overall CCP utilization rate of 21% in 1997 to just under 30% in 2005 for the State of Ohio. (2) Recognition as a ''voice of trust'' among Ohio and national CCP stakeholders (particularly regulatory agencies). (3) Establishment of a national and international reputation, especially for the use of FGD materials and fly ash in construction applications. It is recommended that to increase Ohio's CCP utilization rate from 30% in 2005 to 40% by 2010, the CCP Extension Program be

  5. Coal combustion: Nuclear resource or danger

    SciTech Connect

    Gabbard, A.

    1993-01-01

    Both the benefits and hazards of coal combustion are more far-reaching than are generally recognized. Technologies exist to remove, store, and generate energy from the radioactive isotopes released to the environment by coal combustion. When considering the nuclear consequences of coal combustion, policymakers should look at the data and recognize that the amount of uranium-235 alone dispersed by coal combustion is the equivalent of dozens of nuclear reactor fuel loadings. They should also recognize that the nuclear fuel potential of the fertile isotopes of thorium-232 and uranium-238, which can be converted in reactors to fissionable elements by breeding, yields a virtually unlimited source of nuclear energy that is frequently overlooked as a natural resource. In short, naturally occurring radioactive species released by coal combustion are accumulating in the environment along with minerals such as mercury, arsenic, silicon, calcium, chlorine, and lead, sodium, as well as metals such as aluminum, iron, lead, magnesium, titanium, boron, chromium, and others that are continually dispersed in millions of tons of coal combustion by-products. The potential benefits and threats of these released materials will someday be of such significance that they should not now be ignored.

  6. The coal slime slurry combustion technology

    SciTech Connect

    Li, Y.; Xu, Z.

    1997-12-31

    This paper presents the coal slime slurry combustion technology in circulating fluidized bed (CFB) boilers. The technique is that the slurry-based flow from the concentrator in the coal washery plant directly feeds into the fluidized bed by pump for combustion after a simple filtration and enrichment to an approximate concentration of 50% of coal. The coal slime slurry can burn in a CFB boiler alone or jointly with coal refuse. The technique has been used in a 35 t/h (6MWe) CFB for power generation. The result shows that the combustion efficiency is over 96% and boiler thermal efficiency is over 77%. As compared with burning coal refuse alone, the thermal efficiency was improved by 3--4 percent. This technology is simple, easy to operate and reliable. It is an effective way to utilize coal slime slurry. It has a practical significance for saving coal resources and reducing environmental pollution near coal mine areas. As a clean coal technology, it will result in great social, environmental and economic benefits.

  7. Coal slurry combustion and technology. Volume 2

    SciTech Connect

    Not Available

    1983-01-01

    Volume II contains papers presented at the following sessions of the Coal Slurry Combustion and Technology Symposium: (1) bench-scale testing; (2) pilot testing; (3) combustion; and (4) rheology and characterization. Thirty-three papers have been processed for inclusion in the Energy Data Base. (ATT)

  8. TRACE METAL TRANSFORMATION MECHANISMS DURING COAL COMBUSTION

    EPA Science Inventory

    The article reviews mechanisms governing the fate of trace metals during coal combustion and presents new theoretical results that interpret existing data. Emphasis is on predicting the size-segregated speciation of trace metals in pulverized-coal-fired power plant effluents. Thi...

  9. TRACE METAL TRANSFORMATION MECHANISMS DURING COAL COMBUSTION

    EPA Science Inventory

    The article reviews mechanisms governing the fate of trace metals during coal combustion and presents new theoretical results that interpret existing data. mphasis is on predicting the size-segregated speciation of trace metals in pulverized-coal-fired power plant effluents. his ...

  10. Combustion of dense streams of coal particles

    SciTech Connect

    Annamalai, K.

    1992-04-14

    Research on coal combustion continued. Activities during November 29, 1991 to February 28, 1992 includes: Further analytical results on char array combustion and internal ignition of porous char; preliminary runs using a flat flame burner have been made and a blue flat flame has been obtained; a CID camera, EPIX frame grabber and software, Sony monitor and a 486 Computer to handle image processing frame by frame have been acquired; a new coal feeder has been constructed for feeding through the flat flame burner. Coal experiments have not yet been conducted. Coal samples from Penn State Coal Bank were also acquired for use in the experiments. They include bituminous and subbituminous coals of differing VM.

  11. Low-temperature pyrolysis of brown coal and brown coal containing iron hydroxyl complexes

    SciTech Connect

    George Domazetis; Monthida Raoarun; Bruce D. James

    2006-10-15

    The concentrations profiles of CO{sub 2} and CO have been measured at 150-600{sup o}C from the pyrolysis, at slow heating rates, of acid-washed brown coal and brown coal containing iron hydroxyl complexes. CO{sub 2} formation was greater at low temperatures, but CO increased relative to CO{sub 2} with an increasing temperature. The ratio CO{sub 2}/CO was larger for coal with iron, compared to that from acid-washed coal. The iron species in the chars were Fe{sub 2}O{sub 3} at 200-400{sup o}C, Fe{sub 2}O{sub 3} and Fe{sub 3}O{sub 4} at 400-600{sup o}C, and Fe{sup 0} at 700{sup o}C; inorganic carbonate was also detected. Although conventional chemical kinetic simulations could reproduce the total weight loss of coal with temperature, such calculations could not simulate the measured CO{sub 2} and CO concentration profiles. Decarboxylation reactions may proceed via a number of reaction routes, including ones involving intermediate species. Semiempirical quantum mechanics modeling (SE-QM) of decarboxylation using three carboxylic compounds provided a relative order of decomposition as carboxylic acid {approximately} carboxylate {much_gt} radical. SE-QM and single-point self-consistent field (1scf) calculations, using 2D and 3D models of brown coal, were conducted to provide changes in the heats of formation for models after the loss of carboxyl groups. Such calculations also indicated that hydrogen transfer from a phenoxyl group to a carbanion was energetically favored. The formation of the various iron oxides in coal was modeled by (I) decarboxylation reactions via an iron-carbonato complex decomposing into CO{sub 2} and a {mu}-oxo iron complex and (ii) decarboxylation of coal via the reduction of iron complexes and the formation of organic radicals. 53 refs., 6 figs., 3 tabs.

  12. Health impacts of domestic coal combustion

    SciTech Connect

    Finkelman, R.B.

    1999-07-01

    The US Environmental Protection Agency (EPA) has concluded that, with the possible exception of mercury, there is no compelling evidence to indicate that emissions from coal-burning electric utility generators cause human health problems. The absence of detectable health problems is in part due to the fact that the coals burned in the US generally contain low to modest concentrations of potentially toxic trace elements and that many coal-burning utilities employ sophisticated pollution control systems that efficiently reduce the emissions of hazardous elements. This is not so in many developing countries, especially in homes where coal is used for heating and cooking. Domestic use of coal can present serious human health problems because the coals are generally mined locally with little regard to their composition and the coals are commonly burned in poorly vented or unvented stoves directly exposing residents to the emissions. In China alone several hundred million people commonly burn raw coal in unvented stoves that permeate their homes with high levels of toxic metals and organic compounds. At least 3,000 people in Guizhou Province in southwest China are suffering from severe arsenic poisoning. The primary source of the arsenic appears to be consumption of chili peppers dried over fires fueled with high-arsenic coal. Coal's in the region contain up to 35,000 ppm arsenic. Chili peppers dried over these high-arsenic coal fires absorb 500 ppm arsenic on average. More than 10 million people in Guizhou Province and surrounding areas suffer from dental and skeletal fluorosis. The excess fluorine is due to eating corn dried over burning briquettes made from high-fluorine coals and high-fluoring clay binders. Polycyclic aromatic hydrocarbons formed during coal combustion are believed to cause or contribute to the high incidence of esophageal and lung cancers in parts of China. Domestic coal combustion has also caused selenium poisoning and possibly mercury poisoning

  13. Fluidized bed combustion of low-grade coal and wastes: Research and development

    SciTech Connect

    Borodulya, V.A.; Dikalenko, V.I.; Palchonok, G.I.; Vinogradov, L.M.; Dobkin, S.M.; Telegin, E.M.

    1994-12-31

    Experimental studies were carried out to investigate devolatilization of fuel as single spherical particles of wood, hydrolytic lignin, leather sewage sludge and Belarussian brown coals in a fluidized bed of sand. It is found that the devolatilization process depends on moisture and ash contents in fuel and on the external heat and mass transfer rate. The char combustion occurs largely in the intermediate region. Kinetic parameters of the devolatilization and char combustion are obtained. A low-capacity fluidized bed boiler suitable for combustion of coal and different wastes is described.

  14. Coal combustion aerothermochemistry research. Final report

    SciTech Connect

    Witte, A.B.; Gat, N.; Denison, M.R.; Cohen, L.M.

    1980-12-15

    On the basis of extensive aerothermochemistry analyses, laboratory investigations, and combustor tests, significant headway has been made toward improving the understanding of combustion phenomena and scaling of high swirl pulverized coal combustors. A special attempt has been made to address the gap between scientific data available on combustion and hardware design and scaling needs. Both experimental and theoretical investigations were conducted to improve the predictive capability of combustor scaling laws. The scaling laws derived apply to volume and wall burning of pulverized coal in a slagging high-swirl combustor. They incorporate the findings of this investigation as follows: laser pyrolysis of coal at 10/sup 6/ K/sec and 2500K; effect of coal particle shape on aerodynamic drag and combustion; effect of swirl on heat transfer; coal burnout and slag capture for 20 MW/sub T/ combustor tests for fine and coarse coals; burning particle trajectories and slag capture; particle size and aerodynamic size; volatilization extent and burnout fraction; and preheat level. As a result of this work, the following has been gained: an increased understanding of basic burning mechanisms in high-swirl combustors and an improved model for predicting combustor performance which is intended to impact hardware design and scaling in the near term.

  15. MONITORING STRATEGIES FOR FLUIDIZED BED COMBUSTION COAL PLANTS

    EPA Science Inventory

    Air and water monitoring strategies for commercial-size Fluidized Bed Combustion (FBC) coal plants are presented. This is one of five reports developing air and water monitoring strategies for advanced coal combustion (FBC), coal conversion (coal gasification and liquefaction), a...

  16. Fluidized bed combustion of solid organic wastes and low-grade coals: Research and modeling

    SciTech Connect

    Borodulya, V.A.; Dikalenko, V.I.; Palchonok, G.I.; Stanchits, L.K.

    1995-12-31

    Experimental studies were carried out to investigate devolatilization and combustion of single spherical particles of wood, hydrolytic lignin from ethanol production, leather processing sewage sludge, and low-grade Belarusian brown coals in a fluidized bed of sand. A two-phase model of fluidized bed combustion of biowaste is proposed. The model takes into account combustion of both volatiles and char in the bed as well as in the freeboard. Experimentally obtained characteristics of devolatilization and char combustion are used as parameters of the model proposed.

  17. Enhanced Combustion Low NOx Pulverized Coal Burner

    SciTech Connect

    David Towle; Richard Donais; Todd Hellewell; Robert Lewis; Robert Schrecengost

    2007-06-30

    For more than two decades, Alstom Power Inc. (Alstom) has developed a range of low cost, infurnace technologies for NOx emissions control for the domestic U.S. pulverized coal fired boiler market. This includes Alstom's internally developed TFS 2000{trademark} firing system, and various enhancements to it developed in concert with the U.S. Department of Energy. As of the date of this report, more than 270 units representing approximately 80,000 MWe of domestic coal fired capacity have been retrofit with Alstom low NOx technology. Best of class emissions range from 0.18 lb/MMBtu for bituminous coal to 0.10 lb/MMBtu for subbituminous coal, with typical levels at 0.24 lb/MMBtu and 0.13 lb/MMBtu, respectively. Despite these gains, NOx emissions limits in the U.S. continue to ratchet down for new and existing boiler equipment. On March 10, 2005, the Environmental Protection Agency (EPA) announced the Clean Air Interstate Rule (CAIR). CAIR requires 25 Eastern states to reduce NOx emissions from the power generation sector by 1.7 million tons in 2009 and 2.0 million tons by 2015. Low cost solutions to meet such regulations, and in particular those that can avoid the need for a costly selective catalytic reduction system (SCR), provide a strong incentive to continue to improve low NOx firing system technology to meet current and anticipated NOx control regulations. The overall objective of the work is to develop an enhanced combustion, low NOx pulverized coal burner, which, when integrated with Alstom's state-of-the-art, globally air staged low NOx firing systems will provide a means to achieve: Less than 0.15 lb/MMBtu NOx emissions when firing a high volatile Eastern or Western bituminous coal, Less than 0.10 lb/MMBtu NOx emissions when firing a subbituminous coal, NOx reduction costs at least 25% lower than the costs of an SCR, Validation of the NOx control technology developed through large (15 MWt) pilot scale demonstration, and Documentation required for economic

  18. Electricity from Coal Combustion: Improving the hydrophobicity of oxidized coals

    NASA Astrophysics Data System (ADS)

    Seehra, Mohindar; Singh, Vivek

    2011-03-01

    To reduce pollution and improve efficiency, undesirable mineral impurities in coals are usually removed in coal preparation plants prior to combustion first by crushing and grinding coals followed by gravity separation using surfactant aided water flotation. However certain coals in the US are not amendable to this process because of their poor flotation characteristics resulting in a major loss of an energy resource. This problem has been linked to surface oxidation of mined coals which make these coals hydrophilic. In this project, we are investigating the surface and water flotation properties of the eight Argonne Premium (AP) coals using x-ray diffraction, IR spectroscopy and zeta potential measurements. The role of the surface functional groups, (phenolic -OH and carboxylic -COOH), produced as a result of chemisorptions of O2 on coals in determining their flotation behavior is being explored. The isoelectric point (IEP) in zeta potential measurements of good vs. poor floaters is being examined in order to improved the hydrophobicity of poor floating coals (e.g. Illinois #6). Results from XRD and IR will be presented along with recent findings from zeta potential measurements, and use of additives to improve hydrophobicity. Supported by USDOE/CAST, Contract #DE-FC26-05NT42457.

  19. Statistical kinetics for pulverized coal combustion

    SciTech Connect

    Hurt, R.H.; Lunden, M.M.; Brehob, E.G.; Maloney, D.J.

    1996-06-01

    Coal is a heterogeneous substance whose structure and properties are highly variable on the length scale of the particle sizes used in suspension-fired combustion systems. For certain applications the statistical variations among particles can play an important role. In this paper, three specialized, single-particle techniques are applied to quantify the variations in combustion reactivity and char particle density within pulverized char particle populations. Reactivity variations are investigated through captive particle imaging experiments and entrained flow reactor experiments employing single-particle optical diagnostics. Single-particle density variations are determined directly by a novel technique based on an electrodynamic microbalance equipped with an automated video imaging and image processing system. From these data, a coal-general statistical kinetic model is developed and validated against a large set of single-particle temperature measurements for ten coals of various rank burning in three different combustion environments. The model incorporates a single empirical parameter describing the heterogeneity in reactivity and can adequately describe the entire database using a single coal-independent value of this parameter. The use of the model is demonstrated in a series of numerical simulations of complete burnout process for size-classified and polydisperse fuel samples. The simulations show that incorporating statistical kinetics has an important effect on burnout predictions in certain cases, the importance increasing with decreases in temperature, mean reactivity, and breadth of the particle size distribution. 32 refs.

  20. An annular-furnace boiler for the 660-MW power unit for ultrasupercritical parameters intended for firing brown slagging coals

    NASA Astrophysics Data System (ADS)

    Serant, F. A.; Belorutskii, I. Yu.; Ershov, Yu. A.; Gordeev, V. V.; Stavskaya, O. I.; Katsel, T. V.

    2013-12-01

    We present the main technical solutions adopted in designing annular-furnace boilers intended for operation on brown coals of the prospective Maikubensk open-cast mine in Kazakhstan as part of 660-MW power units for ultrasupercritical steam conditions. Results from 3D modeling of combustion processes are presented, which clearly show the advantages furnaces of this kind have over a traditional furnace in burning heavily slagging brown coals. The layout of the main and boiler auxiliary equipment in the existing boiler cell of the 500-MW power unit at the Ekibastuz GRES-1 district power station is shown. Appropriate attention is paid to matters concerned with decreasing harmful emissions.

  1. Inhibition of spontaneous combustion of coal

    SciTech Connect

    Smith, A.C.; Miron, Y.; Lazzara, C.P.

    1988-01-01

    This report describes laboratory studies conducted to evaluate the effectiveness of 10 additives to inhibit the self-heating of coal. Aqueous additive solutions were applied to a bituminous coal with a high spontaneous combustion potential, and the minimum, self-heating temperatures (SHT's) of the dired coal-additive mixtures were determined in the Bureau's adiabatic heating oven. The relative effectiveness of the additives was determined by the observed changes in the minimum SHT's of the mixtures or by the time required for the sample temperature to reach 150{degrees}C, compared with the untreated coal and coal-water blank. Sodium nitrate, sodium chloride, and calcium carbonate were found to be the most effective inhibitors, followed by ammonium dihydrogen phosphate, calcium chloride ammonium chloride, sodium acetate, and potassium chloride. Two additives, sodium formate and sodium phosphate, promoted the self-heating process. Differential scanning calorimetry experiments on the coal-additive mixtures show that reactions occured between the coal and some of the additives, but these reactions did not infuluence the self-heating process.

  2. Coal combustion science. Quarterly progress report, July--September 1994

    SciTech Connect

    Hardesty, D.R.; Baxter, L.L.; Davis, K.A.; Hurt, R.H.; Yang, N.Y.C.

    1995-09-01

    This document is a quarterly status report of the Coal Combustion Science Project that is being conducted at the Combustion Research Facility, Sandia National Laboratories, Livermore, California. The information reported is for the period July-September 1994. The objective of this work is to support the Office of Fossil Energy in executing research on coal combustion science. This project consists of basic research on coal combustion that supports both the Pittsburgh Energy Technology Center (PETC) Direct Utilization Advanced Research and Technology Development Program, and the International Energy Agency (IEA) Coal Combustion Science Project.

  3. Microwave treatment of a brown coal concentrate from Mugunsk coal for the manufacture of sponge iron

    SciTech Connect

    A.A. Khaidurova; P.N. Konovalov; N.P. Konovalov

    2008-04-15

    A technique for the production of a finely dispersed dry brown coal concentrate with the use of microwave energy is proposed to prepare a charge mixture for the manufacture of sponge iron. The advantages of this technique over analogous industrial processes are demonstrated. The results of experiments on the briquetting of the charge mixture of brown coal and iron ore concentrates without the use of an additional binding agent are described.

  4. EPRI's coal combustion product use research

    SciTech Connect

    Ladwig, K.

    2008-07-01

    For more than 20 years, EPRI's Coal Combustion Product Use Program has been a leader in providing research to demonstrate the value of using coal combustion products (CCPs) in construction and manufacturing. Work is concentrated on large-volume uses, increasing use in traditional applications, uses in light of changes in CCP quality resulting form increased and new air emissions controls for nitrogen oxides, sulfur oxides and mercury. Currently, EPRI is investigating opportunities for using higher volumes of Class C ash in concrete; approaches for ensuring that mercury controls do not adversely affect the use of CCPs; agricultural uses for products from flue gas desulfurization; possible markets for spray dryer absorber byproducts; and issues involved with the presence of ammonia in ash. Some recent results and future work is described in this article. 4 photos.

  5. Coal combustion science. Quarterly progress report, April 1993--June 1993

    SciTech Connect

    Hardesty, D.R.

    1994-05-01

    This document is a quarterly status report of the Coal Combustion Science Project that is being conducted at the Combustion Research Facility, Sandia National Laboratories. The information reported is for Apr-Jun 1993. The objective of this work is to support the Office of Fossil Energy in executing research on coal combustion science. This project consists of basic research on coal combustion that supports both the PETC Direct Utilization Advanced Research and Technology Development Program, and the International Energy Agency Coal Combustion Science Project. The objective of the kinetics and mechanisms of pulverized coal char combustion task is to characterize the combustion behavior of selected US coals under conditions relevant to industrial pulverized coal-fired furnaces. Work is being done in four areas: kinetics of heterogeneous fuel particle populations; char combustion kinetics at high carbon conversion; the role of particle structure and the char formation process in combustion and; unification of the Sandia char combustion data base. This data base on the high temperature reactivities of chars from strategic US coals will permit identification of important fuel-specific trends and development of predictive capabilities for advanced coal combustion systems. The objective of the fate of inorganic material during coal combustion task is the establish a quantitative understanding of the mechanisms and rates of transformation, fragmentation, and deposition of inorganic material during coal combustion as a function of coal type, particle size and temperature, the initial forms and distribution of inorganic species in the unreacted coal, and the local gas temperature and composition. In addition, optical diagnostic capabilities are being developed for in situ, real-time detection of inorganic vapor species and surface species during ash deposition. Selected papers have been indexed separately for inclusion in the Energy Science and Technology Database.

  6. Coal Combustion Products Extension Program

    SciTech Connect

    Tarunjit S. Butalia; William E. Wolfe

    2004-12-31

    The primary objective of the CCP Extension Program is to promote the responsible uses of Ohio CCPs that are technically sound, environmentally safe, and commercially competitive. A secondary objective is to assist other CCP generating states (particularly neighboring states) in establishing CCP use programs within their states. The goal of the CCP extension program at OSU is to work with CCP stakeholders to increase the overall CCP state utilization rate to more than 30% by the year 2005. The program aims to increase FGD utilization for Ohio to more than 20% by the year 2005. The increased utilization rates are expected to be achieved through increased use of CCPs for highway, mine reclamation, agricultural, manufacturing, and other civil engineering uses. In order to accomplish these objectives and goals, the highly successful CCP pilot extension program previously in place at the university has been expanded and adopted by the university as a part of its outreach and engagement mission. The extension program is an innovative technology transfer program with multiple sponsors. The program is a collaborative effort between The Ohio State University (College of Engineering and University Extension Service), United States Department of Energy's National Energy Technology Laboratory, Ohio Department of Development's Coal Development Office, and trade associations such as the American Coal Ash Association as well as the Midwest Coal Ash Association. Industry co-sponsors include American Electric Power, Dravo Lime Company, and ISG Resources. Implementation of the proposed project results in both direct and indirect as well as societal benefits. These benefits include (1) increased utilization of CCPs instead of landfilling, (2) development of proper construction and installation procedures, (3) education of regulators, specification-writers, designers, construction contractors, and the public, (4) emphasis on recycling and decrease in the need for landfill space, (5

  7. COAL COMBUSTION PRODUCTS EXTENSION PROGRAM

    SciTech Connect

    Tarunjit S. Butalia; William E. Wolfe

    2005-05-15

    The primary objective of the CCP Extension Program is to promote the responsible uses of Ohio CCPs that are technically sound, environmentally safe, and commercially competitive. A secondary objective is to assist other CCP generating states (particularly neighboring states) in establishing CCP use programs within their states. The goal of the CCP extension program at OSU is to work with CCP stakeholders to increase the overall CCP state utilization rate to more than 30% by the year 2005. The program aims to increase FGD utilization for Ohio to more than 20% by the year 2005. The increased utilization rates are expected to be achieved through increased use of CCPs for highway, mine reclamation, agricultural, manufacturing, and other civil engineering uses. In order to accomplish these objectives and goals, the highly successful CCP pilot extension program previously in place at the university has been expanded and adopted by the university as a part of its outreach and engagement mission. The extension program is an innovative technology transfer program with multiple sponsors. The program is a collaborative effort between The Ohio State University (College of Engineering and University Extension Service), United States Department of Energy's National Energy Technology Laboratory, Ohio Department of Development's Coal Development Office, and trade associations such as the American Coal Ash Association as well as the Midwest Coal Ash Association. Industry co-sponsors include American Electric Power, Dravo Lime Company, and ISG Resources. Implementation of the proposed project results in both direct and indirect as well as societal benefits. These benefits include (1) increased utilization of CCPs instead of landfilling, (2) development of proper construction and installation procedures, (3) education of regulators, specification-writers, designers, construction contractors, and the public, (4) emphasis on recycling and decrease in the need for landfill space, (5

  8. Coal Combustion Products Extension Program

    SciTech Connect

    Tarunjit S. Butalia; William E. Wolfe

    2003-12-31

    The primary objective of the CCP Extension Program is to promote the responsible uses of Ohio CCPs that are technically sound, environmentally safe, and commercially competitive. A secondary objective is to assist other CCP generating states (particularly neighboring states) in establishing CCP use programs within their states. The goal of the CCP extension program at OSU is to work with CCP stakeholders to increase the overall CCP state utilization rate to more than 30% by the year 2005. The program aims to increase FGD utilization for Ohio to more than 20% by the year 2005. The increased utilization rates are expected to be achieved through increased use of CCPs for highway, mine reclamation, agricultural, manufacturing, and other civil engineering uses. In order to accomplish these objectives and goals, the highly successful CCP pilot extension program previously in place at the university has been expanded and adopted by the university as a part of its outreach and engagement mission. The extension program is an innovative technology transfer program with multiple sponsors. The program is a collaborative effort between The Ohio State University (College of Engineering and University Extension Service), United States Department of Energy's National Energy Technology Laboratory, Ohio Department of Development's Coal Development Office, and trade associations such as the American Coal Ash Association as well as the Midwest Coal Ash Association. Industry co-sponsors include American Electric Power, Dravo Lime Company, and ISG Resources. Implementation of the proposed project results in both direct and indirect as well as societal benefits. These benefits include (1) increased utilization of CCPs instead of landfilling, (2) development of proper construction and installation procedures, (3) education of regulators, specification-writers, designers, construction contractors, and the public, (4) emphasis on recycling and decrease in the need for landfill space, (5

  9. Combustion front propagation in underground coal gasification

    SciTech Connect

    Dobbs, R.L. II; Krantz, W.B.

    1990-10-01

    Reverse Combustion (RC) enhances coal seam permeability prior to Underground Coal Gasification. Understanding RC is necessary to improve its reliability and economics. A curved RC front propagation model is developed, then solved by high activation energy asymptotics. It explicitly incorporates extinction (stoichiometric and thermal) and tangential heat transport (THT) (convection and conduction). THT arises from variation in combustion front temperature caused by tangential variation in the oxidant gas flux to the channel surface. Front temperature depends only weakly on THT; front velocity is strongly affected, with heat loss slowing propagation. The front propagation speed displays a maximum with respect to gas flux. Combustion promoters speed front propagation; inhibitors slow front propagation. The propagation model is incorporated into 2-D simulations of RC channel evolution utilizing the boundary element method with cubic hermetian elements to solve the flow from gas injection wells through the coal to the convoluted, temporally evolving, channel surface, and through the channel to a gas production well. RC channel propagation is studied using 17 cm diameter subbituminous horizontally drilled coal cores. Sixteen experiments at pressures between 2000 and 3600 kPa, injected gas oxygen contents between 21% and 75%, and flows between 1 and 4 standard liters per minute are described. Similarity analysis led to scaling-down of large RC ({approx}1 m) to laboratory scale ({approx}5 cm). Propagation velocity shows a strong synergistic increase at high levels of oxygen, pressure, and gas flow. Char combustion is observed, leaving ash-filled, irregularly shaped channels. Cracks are observed to penetrate the char zone surrounding the channel cores. 69 refs., 54 figs., 4 tabs.

  10. Influence of additives on the increase of the heating value of Bayah’s coal with upgrading brown coal (UBC) method

    SciTech Connect

    Heriyanto, Heri; Widya Ernayati, K.; Umam, Chairul; Margareta, Nita

    2015-12-29

    UBC (upgrading brown coal) is a method of improving the quality of coal by using oil as an additive. Through processing in the oil media, not just the calories that increase, but there is also water repellent properties and a decrease in the tendency of spontaneous combustion of coal products produced. The results showed a decrease in the water levels of natural coal bayah reached 69%, increase in calorific value reached 21.2%. Increased caloric value and reduced water content caused by the water molecules on replacing seal the pores of coal by oil and atoms C on the oil that is bound to increase the percentage of coal carbon. As a result of this experiment is, the produced coal has better calorific value, the increasing of this new calorific value up to 23.8% with the additive waste lubricant, and the moisture content reduced up to 69.45%.

  11. Enhanced Combustion Low NOx Pulverized Coal Burner

    SciTech Connect

    Ray Chamberland; Aku Raino; David Towle

    2006-09-30

    For more than two decades, ALSTOM Power Inc. (ALSTOM) has developed a range of low cost, in-furnace technologies for NOx emissions control for the domestic U.S. pulverized coal fired boiler market. This includes ALSTOM's internally developed TFS 2000 firing system, and various enhancements to it developed in concert with the U.S. Department of Energy (DOE). As of 2004, more than 200 units representing approximately 75,000 MWe of domestic coal fired capacity have been retrofit with ALSTOM low NOx technology. Best of class emissions range from 0.18 lb/MMBtu for bituminous coals to 0.10 lb/MMBtu for subbituminous coals, with typical levels at 0.24 lb/MMBtu and 0.13 lb/MMBtu, respectively. Despite these gains, NOx emissions limits in the U.S. continue to ratchet down for new and existing (retrofit) boiler equipment. If enacted, proposed Clear Skies legislation will, by 2008, require an average, effective, domestic NOx emissions rate of 0.16 lb/MMBtu, which number will be reduced to 0.13 lb/MMBtu by 2018. Such levels represent a 60% and 67% reduction, respectively, from the effective 2000 level of 0.40 lb/MMBtu. Low cost solutions to meet such regulations, and in particular those that can avoid the need for a costly selective catalytic reduction system (SCR), provide a strong incentive to continue to improve low NOx firing system technology to meet current and anticipated NOx control regulations. In light of these needs, ALSTOM, in cooperation with the DOE, is developing an enhanced combustion, low NOx pulverized coal burner which, when integrated with ALSTOM's state-of-the-art, globally air staged low NOx firing systems, will provide a means to achieve less than 0.15 lb/MMBtu NOx at less than 3/4 the cost of an SCR with low to no impact on balance of plant issues when firing a high volatile bituminous coal. Such coals can be more economic to fire than subbituminous or Powder River Basin (PRB) coals, but are more problematic from a NOx control standpoint as existing

  12. Managing coal combustion residues in mines

    SciTech Connect

    2006-07-01

    Burning coal in electric utility plants produces, in addition to power, residues that contain constituents which may be harmful to the environment. The management of large volumes of coal combustion residues (CCRs) is a challenge for utilities, because they must either place the CCRs in landfills, surface impoundments, or mines, or find alternative uses for the material. This study focuses on the placement of CCRs in active and abandoned coal mines. The Committee on Mine Placement of Coal Combustion Wastes of the National Research Council believes that placement of CCRs in mines as part of the reclamation process may be a viable option for the disposal of this material as long as the placement is properly planned and carried out in a manner that avoids significant adverse environmental and health impacts. This report discusses a variety of steps that are involved in planning and managing the use of CCRs as minefills, including an integrated process of CCR characterization and site characterization, management and engineering design of placement activities, and design and implementation of monitoring to reduce the risk of contamination moving from the mine site to the ambient environment. Enforceable federal standards are needed for the disposal of CCRs in minefills to ensure that states have adequate, explicit authority and that they implement minimum safeguards. 267 refs., 6 apps.

  13. Catalytic combustion of coal-derived liquids

    NASA Technical Reports Server (NTRS)

    Bulzan, D. L.; Tacina, R. R.

    1981-01-01

    A noble metal catalytic reactor was tested with three grades of SRC 2 coal derived liquids, naphtha, middle distillate, and a blend of three parts middle distillate to one part heavy distillate. A petroleum derived number 2 diesel fuel was also tested to provide a direct comparison. The catalytic reactor was tested at inlet temperatures from 600 to 800 K, reference velocities from 10 to 20 m/s, lean fuel air ratios, and a pressure of 3 x 10 to the 5th power Pa. Compared to the diesel, the naphtha gave slightly better combustion efficiency, the middle distillate was almost identical, and the middle heavy blend was slightly poorer. The coal derived liquid fuels contained from 0.58 to 0.95 percent nitrogen by weight. Conversion of fuel nitrogen to NOx was approximately 75 percent for all three grades of the coal derived liquids.

  14. Structure-Based Predictive model for Coal Char Combustion.

    SciTech Connect

    Hurt, R.; Colo, J; Essenhigh, R.; Hadad, C; Stanley, E.

    1997-09-24

    During the third quarter of this project, progress was made on both major technical tasks. Progress was made in the chemistry department at OSU on the calculation of thermodynamic properties for a number of model organic compounds. Modelling work was carried out at Brown to adapt a thermodynamic model of carbonaceous mesophase formation, originally applied to pitch carbonization, to the prediction of coke texture in coal combustion. This latter work makes use of the FG-DVC model of coal pyrolysis developed by Advanced Fuel Research to specify the pool of aromatic clusters that participate in the order/disorder transition. This modelling approach shows promise for the mechanistic prediction of the rank dependence of char structure and will therefore be pursued further. Crystalline ordering phenomena were also observed in a model char prepared from phenol-formaldehyde carbonized at 900{degrees}C and 1300{degrees}C using high-resolution TEM fringe imaging. Dramatic changes occur in the structure between 900 and 1300{degrees}C, making this char a suitable candidate for upcoming in situ work on the hot stage TEM. Work also proceeded on molecular dynamics simulations at Boston University and on equipment modification and testing for the combustion experiments with widely varying flame types at Ohio State.

  15. Brown carbon in tar balls from smoldering biomass combustion

    NASA Astrophysics Data System (ADS)

    Chakrabarty, R. K.; Moosmüller, H.; Chen, L.-W. A.; Lewis, K.; Arnott, W. P.; Mazzolen, C.; Dubey, M.; Wold, C. E.; Hao, W. M.; Kreidenweis, S. M.

    2010-03-01

    We report the direct observation of large-scale production of spherical, carbonaceous particles - "tar balls" - from smoldering combustion of two commonly occurring dry mid-latitude fuels. Real-time measurements indicate that brown carbon is an important component of tar balls. The spectrum of the imaginary parts of their complex refractive indices can be described with a Lorentzian-like model with an effective resonance wavelength in the ultraviolet (UV) spectral region. Sensitivity calculations for aerosols containing traditional organic carbon (no absorption at visible and UV wavelengths) and brown carbon suggest that accounting for UV absorption by brown carbon leads to a significant increase in aerosol radiative forcing efficiency and increased atmospheric warming. Since particles from smoldering combustion account for nearly three-fourths of the total carbonaceous aerosol mass emitted globally, inclusion of the optical properties of tar balls into radiative forcing models has significance for the Earth's radiation budget, optical remote sensing, and understanding of anomalous UV absorption in the troposphere.

  16. Brown carbon in tar balls from smoldering biomass combustion

    NASA Astrophysics Data System (ADS)

    Chakrabarty, R. K.; Moosmüller, H.; Chen, L.-W. A.; Lewis, K.; Arnott, W. P.; Mazzoleni, C.; Dubey, M. K.; Wold, C. E.; Hao, W. M.; Kreidenweis, S. M.

    2010-07-01

    We report the direct observation of laboratory production of spherical, carbonaceous particles - "tar balls" - from smoldering combustion of two commonly occurring dry mid-latitude fuels. Real-time measurements of spectrally varying absorption Ångström coefficients (AAC) indicate that a class of light absorbing organic carbon (OC) with wavelength dependent imaginary part of its refractive index - optically defined as "brown carbon" - is an important component of tar balls. The spectrum of the imaginary parts of their complex refractive indices can be described with a Lorentzian-like model with an effective resonance wavelength in the ultraviolet (UV) spectral region. Sensitivity calculations for aerosols containing traditional OC (no absorption at visible and UV wavelengths) and brown carbon suggest that accounting for near-UV absorption by brown carbon leads to an increase in aerosol radiative forcing efficiency and increased light absorption. Since particles from smoldering combustion account for nearly three-fourths of the total carbonaceous aerosol mass emitted globally, inclusion of the optical properties of tar balls into radiative forcing models has significance for the Earth's radiation budget, optical remote sensing, and understanding of anomalous UV absorption in the troposphere.

  17. Mercury emissions from coal combustion in China

    SciTech Connect

    David G. Streets; Jiming Hao; Shuxiao Wang; Ye Wu

    2009-07-01

    This chapter reviews the magnitude and spatial distribution of mercury emissions from coal combustion in China. Due to the large quantities of coal burned and the relatively low level of technology, particularly in industry, emissions are high. Emissions were stable at about 200-210 Mg during the period 1995-2000, but because of rapid economic growth starting in 2001, mercury emissions grew quickly to a value of 334 Mg in 2005. The annual average growth rate for the period 1995-2005 was 5.1%. The uncertainty in emission estimates is about {+-}35% (95% confidence intervals). Emissions are concentrated in those provinces with high concentrations of mercury in coal (like Guizhou Province) and provinces in which a lot of coal is burned (like Shanxi Province). Because significant amounts of coal are burned in homes and small industrial facilities, without any kind of emission control at all, emissions of particulate mercury are higher in China than in the developed world; the speciation profile nationwide is: 64% Hg{sup II}, 19% Hg{sup p}, and 17% Hg{sup 0}. In the future, growth in mercury emissions is expected to be limited by the application of FGD for SO{sub 2} control and other advanced technologies. Estimates of emissions are hampered by the lack of comprehensive and reliable emissions testing programs in China.

  18. Structure Based Predictive Model for Coal Char Combustion

    SciTech Connect

    Robert Hurt; Joseph Calo; Robert Essenhigh; Christopher Hadad

    2000-12-30

    This unique collaborative project has taken a very fundamental look at the origin of structure, and combustion reactivity of coal chars. It was a combined experimental and theoretical effort involving three universities and collaborators from universities outside the U.S. and from U.S. National Laboratories and contract research companies. The project goal was to improve our understanding of char structure and behavior by examining the fundamental chemistry of its polyaromatic building blocks. The project team investigated the elementary oxidative attack on polyaromatic systems, and coupled with a study of the assembly processes that convert these polyaromatic clusters to mature carbon materials (or chars). We believe that the work done in this project has defined a powerful new science-based approach to the understanding of char behavior. The work on aromatic oxidation pathways made extensive use of computational chemistry, and was led by Professor Christopher Hadad in the Department of Chemistry at Ohio State University. Laboratory experiments on char structure, properties, and combustion reactivity were carried out at both OSU and Brown, led by Principle Investigators Joseph Calo, Robert Essenhigh, and Robert Hurt. Modeling activities were divided into two parts: first unique models of crystal structure development were formulated by the team at Brown (PI'S Hurt and Calo) with input from Boston University and significant collaboration with Dr. Alan Kerstein at Sandia and with Dr. Zhong-Ying chen at SAIC. Secondly, new combustion models were developed and tested, led by Professor Essenhigh at OSU, Dieter Foertsch (a collaborator at the University of Stuttgart), and Professor Hurt at Brown. One product of this work is the CBK8 model of carbon burnout, which has already found practical use in CFD codes and in other numerical models of pulverized fuel combustion processes, such as EPRI's NOxLOI Predictor. The remainder of the report consists of detailed technical

  19. Coal combustion products: trash or treasure?

    SciTech Connect

    Hansen, T.

    2006-07-15

    Coal combustion by-products can be a valuable resource to various industries. The American Coal Ash Association (ACAA) collects data on production and uses of coal combustion products (CCPs). 122.5 million tons of CCPs were produced in 2004. The article discusses the results of the ACCA's 2004 survey. Fly ash is predominantly used as a substitute for Portland cement; bottom ash for structural fill, embankments and paved road cases. Synthetic gypsum from the FGD process is commonly used in wallboard. Plant owners are only likely to have a buyer for a portion of their CCPs. Although sale of hot water (from Antelope Valley Station) from condensers for use in a fish farm to raise tilapia proved unviable, the Great Plains Synfuels Plant which manufactures natural gas from lignite produces a wide range of products including anhydrous ammonia, phenol, krypton, carbon dioxide (for enhanced oil recovery), tar oils and liquid nitrogen. ACCA's goal is to educate people about CCPs and how to make them into useful products, and market them, in order to reduce waste disposal and enhance revenue. The article lists members of the ACCA. 2 photos., 1 tab.

  20. STRUCTURE-BASED PREDICTIVE MODEL FOR COAL CHAR COMBUSTION

    SciTech Connect

    CHRISTOPHER M. HADAD; JOSEPH M. CALO; ROBERT H. ESSENHIGH; ROBERT H. HURT

    1998-09-11

    Progress was made this period on a number of tasks. A significant advance was made in the incorporation of macrostructural ideas into high temperature combustion models. Work at OSU by R. Essenhigh in collaboration with the University of Stuttgart has led to a theory that the zone I / II transition in char combustion lies within the range of conditions of interest for pulverized char combustion. The group has presented evidence that some combustion data, previously interpreted with zone II models, in fact takes place in the transition from zone II to zone 1. This idea was used at Brown to make modifications to the CBK model (a char kinetics package specially designed for carbon burnout prediction, currently used by a number of research and furnace modeling groups in academia and industry). The resulting new model version, CBK8, shows improved ability to predict extinction behavior in the late stages of combustion, especially for particles with low ash content. The full development and release of CBK8, along with detailed descriptions of the role of the zone 1/2 transition will be reported on in subsequent reports. ABB-CE is currently implementing CBK7 into a special version of the CFD code Fluent for use in the modeling and design of their boilers. They have been appraised of the development, and have expressed interest in incorporating the new feature, realizing full CBK8 capabilities into their combustion codes. The computational chemistry task at OSU continued to study oxidative pathways for PAH, with emphasis this period on heteroatom containing ring compounds. Preliminary XPS studies were also carried out. Combustion experiments were also carried out at OSU this period, leading to the acquisition of samples at various residence times and the measurement of their oxidation reactivity by nonisothermal TGA techniques. Several members of the project team attended the Carbon Conference this period and made contacts with representatives from the new FETC Consortium

  1. [Retention of selenium volatility using lime in coal combustion].

    PubMed

    Zhang, J; Ren, D; Zhong, Q; Xu, F; Zhang, Y; Yin, J

    2001-05-01

    For understanding the volatility of selenium, the effect of the contents of exchangeable cations of coal on it, and the retention of selenium using CaO in coal combustion, the sequential chemistry extraction, the fixed bed and circulating fluidized bed (CFB) combustion, X-ray diffraction (XRD) and atomic fluorescence spectrometry (AFS) were undertaken. The results showed that the volatility of selenium was more than 97% in coal combustion at 815 degrees C, and the volatility of selenium was affected by the content of exchangeable cations of coal in low-middle temperature. It was identified that lime can restrain the volatility of selenium. In fixed bed combustion of coal, the retention rates of selenium volatility were between 11.6% and 50.7% using lime. In circulating fluidized bed combustion of coal, partitioning of selenium changed very much in ash of different size fraction between without lime and with lime. Comparing with combustion without lime, the content of selenium in ash from chimney was less than fourth times and that in leaching water from chimney decreased by two orders of magnitude using lime. Retention of selenium volatility using lime is so effective in coal combustion, especially in CFB combustion of coal. PMID:11507891

  2. MERCURY CAPTURE ON COAL COMBUSTION FLY ASH. (R827649)

    EPA Science Inventory

    A study was performed at the Energy and Environmental Research Center (EERC) to test the hypotheses that (1) different carbon types contained in coal combustion fly ash have variable sorption capabilities relative to mercury and (2) the inorganic fraction of coal combustion fl...

  3. Coal Combustion Science. Quarterly progress report, October--December 1994

    SciTech Connect

    Hardesty, D.R.; Baxter, L.L.; Davis, K.A.; Hurt, R.H.; Yang, N.Y.C.

    1996-02-01

    The objective of this work is to support the Office of Fossil Energy in executing research on coal combustion science. This project consists of basic research on coal combustion that supports both the Pittsburgh Energy Technology Center (PETC) Direct Utilization Advanced Research and Technology Development Program, and the International Energy Agency (IEA) Coal Combustion Science Project. Specific tasks include: Task 1--Kinetics and mechanisms of pulverized coal char combustion; and Task 2--deposit growth and property development in coal-fired furnaces. The objective of task 1 is to characterize the combustion behavior of selected US coals under conditions relevant to industrial pulverized coal-fired furnaces. Work is being done in four areas: (a) kinetics of heterogeneous fuel particle populations; (b) char combustion kinetics at high carbon conversion; (c) the role of particle structure and the char formation process in combustion and; (d) unification of the Sandia char combustion data base. The objectives of Task 2 are to provide a self-consistent database of simultaneously measured, time-resolved, ash deposit properties in well-controlled and well-defined environments and to provide analytical expressions that relate deposit composition and structure to deposit properties of immediate relevance to PETC`s Combustion 2000 program. The task include the development and use of diagnostics to monitor, in situ and in real time, deposit properties, including information on both the structure and composition of the deposits.

  4. Removal of humic substances from water by brown coal sorbents

    SciTech Connect

    E.V. Veprikova; A.V. Rudkovskii; M.L. Shchipko

    2007-12-15

    Brown coal sorption materials with high activity toward humic substances were prepared using a larger scale laboratory unit with a spouted-bed system. The effect of thermal treatment conditions on the sorption properties of these materials was studied. It was found that the sorption activity of the resulting samples toward humates was closely related to the limiting sorption volume of the materials with respect to benzene.

  5. Ignition and combustion of coal particles

    SciTech Connect

    Gomez, C.O.; Vastola, F.J.

    1983-09-01

    A subbituminous coal was used in this study. Particles from the 850 to 1000 ..mu.. sieve fraction were injected into a reaction furnace swept with air at temperature levels of 928/sup 0/, 980/sup 0/, 1076/sup 0/, 1118/sup 0/ and 1273/sup 0/K. The experimental technique, based upon the simultaneous measurement of the carbon monoxide, carbon dioxide, and the intensity of the light generated during the combustion, provides quantitative information about the ignition and the subsequent burn-off of the residual particle. Homogeneous ignition is detected at temperatures of 1076/sup 0/K and higher. The apparatus designed provides the special characteristics required in this study, and the transition between the ignition mechanisms is achieved within the range of operation conditions for this particular coal. The ignition mechanism is determined not only from the measurement of light intensity during the combustion, but also from the gas evolution curves. The results show the convenience of using these complementary techniques for the measurement of the ignition mechanism. 4 figures, 2 tables.

  6. Combustion behavior of low rank coal water slurries

    SciTech Connect

    Yavuz, R.; Kuecuekbayrak, S.; Williams, A.

    1996-12-31

    Coal water slurries have been developed over the last 15 years as an alternative to fuel oil mainly in industry and power station boilers. Observing of droplet lifetime reveals details of the mechanism of the slurry combustion. In the present investigation, single droplet combustion of lignite water slurries using different Turkish lignites were experimentally studied by using single droplet combustion technique. The technique is based on thermometric method. Results of combustion behavior of low rank coal water slurries were compared with that of high rank coal water slurries which were found in the literature.

  7. On the combustion of bituminous coal chars

    SciTech Connect

    Sahu, R.

    1988-01-01

    The chars were made by pyrolyzing size-graded PSOC 1451 coal particles in nitrogen at 1000-1600K. Sized char particles were then used in subsequent experiments. Low temperature reactivities of such cenospheric chars were measured at 800K in a TGA. The effects of initial coal size, char size, pyrolysis temperature, and oxygen concentration were investigated. Single particle combustion experiments were done in both air and 50 percent oxygen ambients at 1000-1500K wall temperatures in a drop-tube laminar-flow reactor. The ignition transients of single burning particles were explained using a simple thermal model. Char samples were also partially oxidized at 1200-1500K and then physically characterized using optical and electron microscopy, gas adsorption methods, and mercury porosimetry. Results of characterization were compared to those done at 800K. Single particle combustion was numerically modeled. At first, a continuum model for asymptotic shrinking-core combustion was developed using apparent reaction rate and temperature-dependent properties. Later, a more general continuum model was developed that treated the internal morphology of the particles more realistically, as inferred from experiments. The steady-state diffusion equation was solved inside the particle to determine its theoretical temperature-time history. Good agreement with experimental results was found. The model was extended to include the effect of nonlinear kinetics. A discrete model for a cenospheric char particle was also developed, in which spherical voids were randomly placed in a spherical particle. Connectivity of the internal pore structure was accounted for.

  8. STRUCTURE-BASED PREDICTIVE MODEL FOR COAL CHAR COMBUSTION

    SciTech Connect

    CHRISTOPHER M. HADAD; JOSEPH M. CALO; ROBERT H. ESSENHIGH; ROBERT H. HURT

    1998-06-04

    During the past quarter of this project, significant progress continued was made on both major technical tasks. Progress was made at OSU on advancing the application of computational chemistry to oxidative attack on model polyaromatic hydrocarbons (PAHs) and graphitic structures. This work is directed at the application of quantitative ab initio molecular orbital theory to address the decomposition products and mechanisms of coal char reactivity. Previously, it was shown that the �hybrid� B3LYP method can be used to provide quantitative information concerning the stability of the corresponding radicals that arise by hydrogen atom abstraction from monocyclic aromatic rings. In the most recent quarter, these approaches have been extended to larger carbocyclic ring systems, such as coronene, in order to compare the properties of a large carbonaceous PAH to that of the smaller, monocyclic aromatic systems. It was concluded that, at least for bond dissociation energy considerations, the properties of the large PAHs can be modeled reasonably well by smaller systems. In addition to the preceding work, investigations were initiated on the interaction of selected radicals in the �radical pool� with the different types of aromatic structures. In particular, the different pathways for addition vs. abstraction to benzene and furan by H and OH radicals were examined. Thus far, the addition channel appears to be significantly favored over abstraction on both kinetic and thermochemical grounds. Experimental work at Brown University in support of the development of predictive structural models of coal char combustion was focused on elucidating the role of coal mineral matter impurities on reactivity. An �inverse� approach was used where a carbon material was doped with coal mineral matter. The carbon material was derived from a high carbon content fly ash (Fly Ash 23 from the Salem Basin Power Plant. The ash was obtained from Pittsburgh #8 coal (PSOC 1451). Doped

  9. DEVELOPMENT OF A VORTEX CONTAINMENT COMBUSTOR FOR COAL COMBUSTION SYTEMS

    EPA Science Inventory

    The report describes the development of a vortex containment combustor (VCC) for coal combustion systems, designed to solve major problems facing the conversion of oil- and gas-fired boilers to coal (e.g., derating, inorganic impurities in coal, and excessive formation of NOx and...

  10. DEVELOPMENT OF A VORTEX CONTAINMENT COMBUSTOR FOR COAL COMBUSTION SYSTEMS

    EPA Science Inventory

    The report describes the development of a vortex containment combustor (VCC) for coal combustion systems, designed to solve major problems facing the conversion of oil- and gas-fired boilers to coal (e.g., derating, inorganic impurities in coal, and excessive formation of NOx and...

  11. [Coal fineness effect on primary particulate matter features during pulverized coal combustion].

    PubMed

    Lü, Jian-yi; Li, Ding-kai

    2007-09-01

    Three kinds of coal differed from fineness were burned in a laboratory-scale drop tube furnace for combustion test, and an 8-stage Andersen particle impactor was employed for sampling the primary particulate matter (PM), in order to study coal fineness effect on primary PM features during pulverized coal combustion. It has been shown that the finer the coal was, the finer the PM produced. PM, emission amount augmented with coal fineness decreased, and the amount of PM10 increased from 13 mg/g to 21 mg/g respectively generated by coarse coal and fine coal. The amount of PM2.5 increased from 2 mg/g to 8 mg/g at the same condition. Constituents and content in bulk ash varied little after three different fineness coal combustion, while the appearance of grading PM differed visibly. The value of R(EE) increased while the coal fineness deceased. The volatility of trace elements which were investigated was Pb > Cr > Zn > Cu > Ni in turn. The concentration of poisonous trace elements was higher which generated from fine coal combustion. The volatilization capacity was influenced little by coal fineness, but the volatilization extent was influenced differently by coal fineness. Fine coal combustion affects worse environment than coarse coal does. PMID:17990536

  12. Plane flame furnace combustion tests on JPL desulfurized coal

    NASA Technical Reports Server (NTRS)

    Reuther, J. J.; Kim, H. T.; Lima, J. G. H.

    1982-01-01

    The combustion characteristics of three raw bituminous (PSOC-282 and 276) and subbituminous (PSOC-230) coals, the raw coals partially desulfurized (ca -60%) by JPL chlorinolysis, and the chlorinated coals more completely desulfurized (ca -75%) by JPL hydrodesulfurization were determined. The extent to which the combustion characteristics of the untreated coals were altered upon JPL sulfur removal was examined. Combustion conditions typical of utility boilers were simulated in the plane flame furnace. Upon decreasing the parent coal voltaile matter generically by 80% and the sulfur by 75% via the JPL desulfurization process, ignition time was delayed 70 fold, burning velocity was retarded 1.5 fold, and burnout time was prolonged 1.4 fold. Total flame residence time increased 2.3 fold. The JPL desulfurization process appears to show significant promise for producing technologically combustible and clean burning (low SO3) fuels.

  13. Thermally induced structural changes in coal combustion

    SciTech Connect

    Flagan, R.C.; Gavalas, G.R.

    1992-01-01

    The effects of the temperature-time history during coal devolitization and oxidation on the physical properties and the reactivity of resulting char were studied experimentally for temperatures and residence times typical of pulverized combustion. Experiments were also carried out at somewhat lower temperatures and correspondingly longer residence times. An electrically heated laminar flow reactor was used to generate char and measure the rates of oxidation at gas temperatures about 1600K. Partially oxidized chars were extracted and characterized by gas adsorption and mercury porosimetry, optical and scanning electron microscopy, and oxidation in a thermogravimetric analysis system (TGA). A different series of experiments was conducted using a quadrople electrodynamic balance. Single particles were suspended electrodynamically and heated by an infrared laser in an inert or oxygen-containing atmosphere. During the laser heating, measurements were taken of particle mass, size/shape, and temperature.

  14. Effect of the process conditions of aerobic bioconversion on the characteristics of biologically processed brown coals

    SciTech Connect

    I.P. Ivanov

    2007-04-15

    The effect of the laboratory and pilot process conditions of the aerobic bioconversion of brown coals on the elemental composition and technical characteristics of the organic matter of the resulting biologically processed coals is reported.

  15. MECHANISMS AND OPTIMIZATION OF COAL COMBUSTION

    SciTech Connect

    Kyriacos Zygourakis

    2000-10-31

    The completed research project has made some significant contributions that will help us meet the challenges outlined in the previous section. One of the major novelties of our experimental approach involves the application of video microscopy and digital image analysis to study important transient phenomena (like particle swelling and ignitions) occurring during coal pyrolysis and combustion. Image analysis was also used to analyze the macropore structure of chars, a dominant factor in determining char reactivity and ignition behavior at high temperatures where all the commercial processes operate. By combining advanced experimental techniques with mathematical modeling, we were able to achieve the main objectives of our project. More specifically: (1) We accurately quantified the effect of several important process conditions (like pyrolysis heating rate, particle size, heat treatment temperature and soak time) on the combustion behavior of chars. These measurements shed new light into the fundamental mechanisms of important transient processes like particle swelling and ignitions. (2) We developed and tested theoretical models that can predict the ignition behavior of char particles and their burn-off times at high temperatures where intraparticle diffusional limitations are very important.

  16. HIGH PRESSURE COAL COMBUSTION KINETICS PROJECT

    SciTech Connect

    Chris Guenther; Bill Rogers

    2001-09-15

    The HPCCK project was initiated with a kickoff meeting held on June 12, 2001 in Morgantown, WV, which was attended by all project participants. SRI's existing g-RCFR reactor was reconfigured to a SRT-RCFR geometry (Task 1.1). This new design is suitable for performing the NBFZ experiments of Task 1.2. It was decided that the SRT-RCFR apparatus could be modified and used for the HPBO experiments. The purchase, assembly, and testing of required instrumentation and hardware is nearly complete (Task 1.1 and 1.2). Initial samples of PBR coal have been shipped from FWC to SRI (Task 1.1). The ECT device for coal flow measurements used at FWC will not be used in the SRI apparatus and a screw type feeder has been suggested instead (Task 5.1). NEA has completed a upgrade of an existing Fluent simulator for SRI's RCFR to a version that is suitable for interpreting results from tests in the NBFZ configuration (Task 1.3) this upgrade includes finite-rate submodels for devolatilization, secondary volatiles pyrolysis, volatiles combustion, and char oxidation. Plans for an enhanced version of CBK have been discussed and development of this enhanced version has begun (Task 2.5). A developmental framework for implementing pressure and oxygen effects on ash formation in an ash formation model (Task 3.3) has begun.

  17. Coal combustion: Science and technology of industrial and utility applications

    SciTech Connect

    Feng, J.

    1988-01-01

    Despite the competition of oil and gas and the increasing importance of nuclear power, coal is still one of the main sources of energy in the world. In some regions of the world, the reserve of oil and natural gas is nearly depleted. The supply of such fuels relies on shipment from foreign countries, and may be vulnerable to political crisis, while coals are still abundant and easily available. Therefore, the technology of burning coal for energy, which seems rather old, has not lost its vitality and is in fact developing fast. Because of industry development, especially in developing countries, more and more coal is burned each year. If coal is not burned properly, it may pollute the environment and affect the ecological balance of the surrounding regions. Great attention has been paid to curb these issues, and significant progress has been achieved. Technology of desulfurization of flue gases, low nitrogen oxide coal burners, and also the technology of clean burning of coal by fluidized-bed combustion have all been developed and commercialized. Further improvements are under development. At the same time, new techniques have been used in the measurements and diagnoses of coal combustion. These new techniques facilitate more efficient and cleaner burning of coal. Although coal combustion is a very complicated physiochemical phenomenon, the use of the computer enables and pushes forward the theoretical analysis of coal combustion. Besides, the mathematical modelling of the coal combustion process is also a fast progressing field of research and encouraging results have been obtained by scientists throughout the world. This book compiles the papers presented in the conference on the subject of clean cool technology and fluidized-bed combustion.

  18. Influence of combustion conditions and coal properties on physical properties of fly ash generated from pulverized coal combustion

    SciTech Connect

    Hiromi Shirai; Hirofumi Tsuji; Michitaka Ikeda; Toshinobu Kotsuji

    2009-07-15

    To develop combustion technology for upgrading the quality of fly ash, the influences of the coal properties, such as the size of pulverized coal particles and the two-stage combustion ratio during the combustion, on the fly ash properties were investigated using our test furnace. The particle size, density, specific surface area (obtained by the Blaine method), and shape of fly ash particles of seven types of coal were measured. It was confirmed that the size of pulverized coal particles affects the size of the ash particles. Regarding the coal properties, the fuel ratio affected the ash particle size distribution. The density and shape of the ash particles strongly depended on their ash size. Our results indicated that the shape of the ash particles and the concentration of unburned carbon affected the specific surface area. The influence of the two-stage combustion ratio was limited. 8 refs., 13 figs., 3 tabs.

  19. Plasma-supported coal combustion in boiler furnace

    SciTech Connect

    Askarova, A.S.; Karpenko, E.I.; Lavrishcheva, Y.I.; Messerle, V.E.; Ustimenko, A.B.

    2007-12-15

    Plasma activation promotes more effective and environmentally friendly low-rank coal combustion. This paper presents Plasma Fuel Systems that increase the burning efficiency of coal. The systems were tested for fuel oil-free start-up of coal-fired boilers and stabilization of a pulverized-coal flame in power-generating boilers equipped with different types of burners, and burning all types of power-generating coal. Also, numerical modeling results of a plasma thermochemical preparation of pulverized coal for ignition and combustion in the furnace of a utility boiler are discussed in this paper. Two kinetic mathematical models were used in the investigation of the processes of air/fuel mixture plasma activation: ignition and combustion. A I-D kinetic code PLASMA-COAL calculates the concentrations of species, temperatures, and velocities of the treated coal/air mixture in a burner incorporating a plasma source. The I-D simulation results are initial data for the 3-D-modeling of power boiler furnaces by the code FLOREAN. A comprehensive image of plasma-activated coal combustion processes in a furnace of a pulverized-coal-fired boiler was obtained. The advantages of the plasma technology are clearly demonstrated.

  20. USGS TOXIC SUBSTANCES FROM COAL COMBUSTION -- FORMS OF OCCURRENCE ANALYSIS

    SciTech Connect

    Allan Kolker; Stanley J. Mroczkowski; Curtis A. Palmer; Robert B. Finkelman

    1999-04-01

    Detailed information on trace-element modes of occurrence in coal is essential to understanding and predicting trace-element transformations taking place during coal combustion. The USGS has developed quantitative and semi-quantitative methods for determining the mode of occurrence of trace elements in coal. This information is needed to generate predictive models for trace-element behavior, the ultimate goal of DOE contract DE-AC22-95PC95101 ``Toxic Substances From Coal Combustion--A Comprehensive Assessment'' awarded to PSI, Inc. USGS activities in support of this contract have a direct bearing on the predictive equations being developed as the primary product of the PSI program.

  1. Carbon dioxide from coal combustion: Variation with rank of US coal

    USGS Publications Warehouse

    Quick, J.C.; Glick, D.C.

    2000-01-01

    Carbon dioxide from combustion of US coal systematically varies with ASTM rank indices, allowing the amount of CO2 produced per net unit of energy to be predicted for individual coals. No single predictive equation is applicable to all coals. Accordingly, we provide one equation for coals above high volatile bituminous rank and another for lower rank coals. When applied to public data for commercial coals from western US mines these equations show a 15% variation of kg CO2 (net GJ)-1. This range of variation suggests reduction of US CO2 emissions is possible by prudent selection of coal for combustion. Maceral and mineral content are shown to slightly affect CO2 emissions from US coal. We also suggest that CO2 emissions increased between 6 and 8% in instances where Midwestern US power plants stopped burning local, high-sulfur bituminous coal and started burning low-sulfur, subbituminous C rank coal from the western US.

  2. Combustion characterization of beneficiated coal-based fuels

    SciTech Connect

    Chow, O.K.; Nsakala, N.Y.

    1990-11-01

    The Pittsburgh Energy Technology Center of the US Department of Energy has contracted with Combustion Engineering, Inc. (CE) to perform a three-year project on Combustion Characterization of Beneficiated Coal-Based Fuels.'' The beneficiated coals are produced by other contractors under the DOE Coal Preparation Program. Several contractor-developed advanced coal cleaning processes are being run at the cleaning facility in Homer City, Pennsylvania, to produce 20-ton batches of fuels for shipment to CE's laboratory in Windsor, Connecticut. CE then processes the products into either a coal-water fuel (CVVT) or a dry microfine pulverized coal (DMPC) form for combustion testing. The objectives of this project include: (1) the development of an engineering data base which will provide detailed information on the properties of BCFs influencing combustion, ash deposition, ash erosion, particulate collection, and emissions; and (2) the application of this technical data base to predict the performance and economic impacts of firing the BCFs in various commercial boiler designs. The technical approach used to develop the technical data includes: bench-scale fuel property, combustion, and ash deposition tests; pilot-scale combustion and ash effects tests; and full-scale combustion tests. Subcontractors to CE to perform parts of the test work are the Massachusetts Institute of Technology (MIT), Physical Science, Inc. Technology Company (PSIT) and the University of North Dakota Energy and Environmental Research Center (UNDEERC). Twenty fuels will be characterized during the three-year base program: three feed coals, fifteen BCFS, and two conventionally cleaned coals for full-scale tests. Approximately, nine BCFs will be in dry microfine coal (DMPC) form, and six BCFs will be in coal-water fuel (CWF) form. Additional BCFs would be characterized during optional project supplements.

  3. Hardened, environmentally disposable composite granules of coal cleaning refuse, coal combustion waste, and other wastes, and method preparing the same

    DOEpatents

    Burnet, George; Gokhale, Ashok J.

    1990-07-10

    A hardened, environmentally inert and disposable composite granule of coal cleaning refuse and coal combustion waste, and method for producing the same, wherein the coal combustion waste is first granulated. The coal cleaning refuse is pulverized into fine particles and is then bound, as an outer layer, to the granulated coal combustion waste granules. This combination is then combusted and sintered. After cooling, the combination results in hardened, environmentally inert and disposable composite granules having cores of coal combustion waste, and outer shells of coal cleaning refuse. The composite particles are durable and extremely resistant to environmental and chemical forces.

  4. Hardened, environmentally disposable composite granules of coal cleaning refuse, coal combustion waste, and other wastes, and method preparing the same

    SciTech Connect

    Burnet, G.; Gokhale, A.J.

    1990-07-10

    A hardened, environmentally inert and disposable composite granule of coal cleaning refuse and coal combustion waste and method for producing the same are disclosed, wherein the coal combustion waste is first granulated. The coal cleaning refuse is pulverized into fine particles and is then bound, as an outer layer, to the granulated coal combustion waste granules. This combination is then combusted and sintered. After cooling, the combination results in hardened, environmentally inert and disposable composite granules having cores of coal combustion waste, and outer shells of coal cleaning refuse. The composite particles are durable and extremely resistant to environmental and chemical forces. 3 figs.

  5. Formation of NH{sub 3} during the pyrolysis of a brown coal

    SciTech Connect

    Li, C.Z.; Pang, Y.; Li, X.G.

    1998-12-31

    Emissions of oxides of nitrogen (NO, NO{sub 2} and N{sub 2}O) from power generation using coal are an important environmental problem, contributing to the formation of photochemical smog and acid rain or to the enhancement of greenhouse effects and to the enhanced depletion of stratospheric ozone. During pyrolysis, the nitrogen in coal, as a part of coal organic matter, is converted into NOx precursors (eg. NH{sub 3}, HCN, HNCO and the nitrogen in tar and char). These NOx precursors may then be converted into either NOx or N{sub 2} during subsequent combustion or gasification/combustion. The conversion efficiency of these NOx precursors into NOx depends strongly upon the type of NOx precursor. Knowledge of the formation of these NOx precursors during pyrolysis is therefore essential for the accurate predictions of NOx emissions from large scale power plants, and therefore for the development of optimum strategies for NOx reduction. Formation of NH{sub 3} during the pyrolysis of a Victorian brown coal (Loy Yang) has been studied in a novel reactor. The experimental results obtained suggest that a considerable amount of the nitrogen in the nascent char could be converted into NH{sub 3} if the char is held at high temperatures for a long period of time. The formation of NH{sub 3} from the thermal cracking of char was seen to last for more than an hour even at temperatures as high as 700--900 C. The experimental results seem to suggest that the differences in reactor geometries would account at least partially for some of the discrepancies in the literature regarding the formation of NH{sub 3} during the pyrolysis of coals. It is thought that NH{sub 3} may be formed from the hydrogenation of the N sites in the char by the active hydrogen generated from the thermal cracking of the char.

  6. Combustion characterization of beneficiated coal-based fuels

    SciTech Connect

    Chow, O.K.; Levasseur, A.A.

    1995-11-01

    The Pittsburgh Energy Technology Center (PETC) of the U.S. Department of Energy is sponsoring the development of advanced coal-cleaning technologies aimed at expanding the use of the nation`s vast coal reserves in an environmentally and economically acceptable manner. Because of the lack of practical experience with deeply beneficiated coal-based fuels, PETC has contracted Combustion Engineering, Inc. to perform a multi-year project on `Combustion Characterization of Beneficiated Coal-Based Fuels.` The objectives of this project include: (1) the development of an engineering data base which will provide detailed information on the properties of Beneficiated Coal-Based Fuels (BCs) influencing combustion, ash deposition, ash erosion, particulate collection, and emissions; and (2) the application of this technical data base to predict the performance and economic impacts of firing the BCFs in various commercial boiler designs.

  7. Preparation of oxygen-containing organic products from bed-oxidized brown coal by ozonation

    SciTech Connect

    Semenova, S.A.; Patrakov, Y.F.; Batina, M.V.

    2009-01-15

    The possibility of modifying the functional composition of humic acids by gas-phase ozonation of bed-oxidized brown coal was examined. About 90% of the organic matter of brown coal was converted to low-molecular weight soluble oxygen-containing products by stepwise liquid-phase ozonation (in chloroform and acetic acid).

  8. Analysis of cyclic combustion of the coal-water suspension

    NASA Astrophysics Data System (ADS)

    Kijo-Kleczkowska, Agnieszka

    2011-04-01

    Combustion technology of the coal-water suspension creates a number of new possibilities to organize the combustion process fulfilling contemporary requirements, e.g. in the environment protection. Therefore the in-depth analysis is necessary to examine the technical application of coal as a fuel in the form of suspension. The research undertakes the complex investigations of the continuous coal-water suspension as well as cyclic combustion. The cyclic nature of fuel combustion results from the movement of the loose material in the flow contour of the circulating fluidized bed (CFB): combustion chamber, cyclone and downcomer. The experimental results proved that the cyclic change of oxygen concentration around fuel, led to the vital change of both combustion mechanisms and combustion kinetics. The mathematical model of the process of fuel combustion has been presented. Its original concept is based on the allowance for cyclic changes of concentrations of oxygen around the fuel. It enables the prognosis for change of the surface and the centre temperatures as well as mass loss of the fuel during combustion in air, in the fluidized bed and during the cyclic combustion.

  9. Analysis and comparison of two Victorian Brown Coal resinite samples

    SciTech Connect

    Anderson, K.B.; Botto, R.E.; Dyrkacz, G.R.; Hayatsu, R.; Winans, R.E. )

    1989-01-01

    Among the organic constituents of coal, the maceral resinite is probably the least complex structurally, due to the relatively simple composition of the original resins. Hence, with careful analysis, it may be possible to construct meaningful and accurate structural descriptions of this maceral. For the purposes of this study, two physically diverse resinite samples were obtained from Victorian Brown Coal (VBC) by hand picking from open cut mine faces. The first sample, which is referred to as resinite'' throughout this text is a hard, brittle, glassy material, yellow/brown in color. The second is a soft, brittle, bone white material, which was found in association with a large gymnosperm log, of undetermined paleobotanical affinity, as sheets between wood'' and bark.'' This material is sometimes referred to as bombicite'' by geologists, and is referred to by this name in this text in the interests of clarity. Petrographically, both samples are classified as resinite. Pyrolysis-high resolution mass spectra were recorded on a Kratos MS-50 mass spectrometer. FTIR spectra were recorded on a Bruker 113 V FTIR spectrometer. CP/MAS {sup 13}C NMR spectra were recorded on a Bruker CPX-100 NMR spectrometer. 7 refs., 3 figs., 1 tab.

  10. AIR EMISSIONS FROM COMBUSTION OF SOLVENT REFINED COAL

    EPA Science Inventory

    The report gives details of a Solvent Refined Coal (SRC) combustion test at Georgia Power Company's Plant Mitchell, March, May, and June 1977. Flue gas samples were collected for modified EPA Level 1 analysis; analytical results are reported. Air emissions from the combustion of ...

  11. ANALYSIS FOR RADIONUCLIDES IN SRC AND COAL COMBUSTION SAMPLES

    EPA Science Inventory

    The report deals with the determination of the levels of uranium, thorium, and their daughter products in coal, SRC, coal flyash, and SRC flyash samples taken from Georgia Power Company's Plant Mitchell during the May and June 1977 combustion tests to compare the environmental em...

  12. The characterization of brown coals of Kansk-Achinsk Basin for improved utilization in the coal-burning power stations

    SciTech Connect

    Solntsev, S.I.; Shorokhov, V.P.

    1998-12-31

    Kansk-Achinsk Brown Coal Basin in Siberia is the largest one of Russia. There are several large deposits in the Basin. Two main open cuts currently annually supply 35 million tonnes of brown coal for the pulverized fired boilers operated by number of Power Stations in Central Siberia. The main part of Kansk-Achinsk brown coals are characterized by low sulfur, nitrogen and heavy metal content. However, they differ in the ash content (within the range of 4--12%) and in the ash composition (in Ca, Al, Fe, Na, in particular). This has a major influence on the boiler fouling and slagging tendency. The paper describes the work in defining the geological, chemical and utilization characteristics of the coals from the different cuts and places of Kansk-Achinsk Basin. The emphasis on the ash fouling and slagging on burning brown coals from different places was made. The methods of coal preparation were developed to improve the utilization characteristics and to comply with the emission regulations. The preparation and burning of blended coals and coal-water slurry is the focus of the discussion. The technology of briquetted brown coal both with oil-derived binder and with no binder is described.

  13. Compilation of Sandia coal char combustion data and kinetic analyses

    SciTech Connect

    Mitchell, R.E.; Hurt, R.H.; Baxter, L.L.; Hardesty, D.R.

    1992-06-01

    An experimental project was undertaken to characterize the physical and chemical processes that govern the combustion of pulverized coal chars. The experimental endeavor establishes a database on the reactivities of coal chars as a function of coal type, particle size, particle temperature, gas temperature, and gas and composition. The project also provides a better understanding of the mechanism of char oxidation, and yields quantitative information on the release rates of nitrogen- and sulfur-containing species during char combustion. An accurate predictive engineering model of the overall char combustion process under technologically relevant conditions in a primary product of this experimental effort. This document summarizes the experimental effort, the approach used to analyze the data, and individual compilations of data and kinetic analyses for each of the parent coals investigates.

  14. Active carbons and clean briquettes from the modified Kansk-Achinsk brown coal

    SciTech Connect

    Kuznetsov, P.N.; Kuznetsova, L.I.; Kontzevoi, A.A.; Pozharnikov, V.A.

    1996-12-31

    The effect of modification of Kansk Achinsk Brown coal by means of chemical and mechanical pretreatments as well as by hydrolyzed lignin addition on coal briquetting was studied. Coal briquettes were then pyrolyzed and steam activated at 700--800 C to prepare the active carbons. The main focus was to analyze how macromolecular structure of brown coal affect the properties of briquettes and the sorption and mechanical properties of activated carbons and to investigate the potential for the production of clean briquetted fuel and high performance carbon adsorbents through the directive modification of coal.

  15. Preparation of waxes and humic acids from brown coal from the Sergeevskoe deposit

    SciTech Connect

    L.P. Noskova; A.V. Rokhin; A.P. Sorokin

    2007-06-15

    The comparative extraction of coal with organic solvents was performed. Humic acids were separated from solid residues. The yields, particle-size distributions, and chemical compositions of the resulting products were analyzed. It was demonstrated that brown-coal wax and humic fertilizers can potentially be obtained using coal from the Sergeevskoe deposit.

  16. Combustion of black coal in the form of coal-water slurry in low-capacity boilers

    NASA Astrophysics Data System (ADS)

    Maltsev, L. I.; Kravchenko, I. V.; Lazarev, S. I.; Lapin, D. A.

    2014-07-01

    The present paper describes the examples of experimental and industrial implementation of technologies of flame-droplet combustion of the coal-water mixture in furnaces above a bed consisting of burning coal and in a swirling-type furnace chamber. For preparing coal-water fuel (CWF), Kuznetsk coals of G and D ranks, as well as tailings of coking coals, were used. The future prospect of both technologies of coal combustion has been shown from both economic and environmental standpoints.

  17. Structure-Based Predictive Model for Coal Char Combustion

    SciTech Connect

    Christopher Hadad; Joseph Calo; Robert Essenhigh; Robert Hurt

    1998-04-08

    Progress was made this period on a number of separate experimental and modelling activities. At Brown, the models of carbon nanostructure evolution were expanded to consider high-rank materials with initial anisotropy. The report presents detailed results of Monte Carlo simulations with non-zero initial layer length and with statistically oriented initial states. The expanded simulations are now capable of describing the development of nanostructure during carbonization of most coals. Work next quarter will address the remaining challenge of isotropic coke-forming coals. Experiments at Brown yielded important data on the "memory loss" phenomenon in carbon annealing, and on the effect of mineral matter on high-temperature reactivity. The experimental aspects of the Brown work will be discussed in detail in the next report.

  18. Mercury in coal and the impact of coal quality on mercury emissions from combustion systems

    USGS Publications Warehouse

    Kolker, A.; Senior, C.L.; Quick, J.C.

    2006-01-01

    The proportion of Hg in coal feedstock that is emitted by stack gases of utility power stations is a complex function of coal chemistry and properties, combustion conditions, and the positioning and type of air pollution control devices employed. Mercury in bituminous coal is found primarily within Fe-sulfides, whereas lower rank coal tends to have a greater proportion of organic-bound Hg. Preparation of bituminous coal to reduce S generally reduces input Hg relative to in-ground concentrations, but the amount of this reduction varies according to the fraction of Hg in sulfides and the efficiency of sulfide removal. The mode of occurrence of Hg in coal does not directly affect the speciation of Hg in the combustion flue gas. However, other constituents in the coal, notably Cl and S, and the combustion characteristics of the coal, influence the species of Hg that are formed in the flue gas and enter air pollution control devices. The formation of gaseous oxidized Hg or particulate-bound Hg occurs post-combustion; these forms of Hg can be in part captured in the air pollution control devices that exist on coal-fired boilers, without modification. For a given coal type, the capture efficiency of Hg by pollution control systems varies according to type of device and the conditions of its deployment. For bituminous coal, on average, more than 60% of Hg in flue gas is captured by fabric filter (FF) and flue-gas desulfurization (FGD) systems. Key variables affecting performance for Hg control include Cl and S content of the coal, the positioning (hot side vs. cold side) of the system, and the amount of unburned C in coal ash. Knowledge of coal quality parameters and their effect on the performance of air pollution control devices allows optimization of Hg capture co-benefit. ?? 2006 Elsevier Ltd. All rights reserved.

  19. Chemical analyses of coal, coal-associated rocks and coal combustion products collected for the National Coal Quality Inventory

    USGS Publications Warehouse

    Hatch, Joseph R.; Bullock, John H., Jr.; Finkelman, Robert B.

    2006-01-01

    In 1999, the USGS initiated the National Coal Quality Inventory (NaCQI) project to address a need for quality information on coals that will be mined during the next 20-30 years. At the time this project was initiated, the publicly available USGS coal quality data was based on samples primarily collected and analyzed between 1973 and 1985. The primary objective of NaCQI was to create a database containing comprehensive, accurate and accessible chemical information on the quality of mined and prepared United States coals and their combustion byproducts. This objective was to be accomplished through maintaining the existing publicly available coal quality database, expanding the database through the acquisition of new samples from priority areas, and analysis of the samples using updated coal analytical chemistry procedures. Priorities for sampling include those areas where future sources of compliance coal are federally owned. This project was a cooperative effort between the U.S. Geological Survey (USGS), State geological surveys, universities, coal burning utilities, and the coal mining industry. Funding support came from the Electric Power Research Institute (EPRI) and the U.S. Department of Energy (DOE).

  20. The release of iron during coal combustion. Milestone report

    SciTech Connect

    Baxter, L.L.

    1995-06-01

    Iron plays an important role in the formation of both fly ash and deposits in many pulverized-coal-fired boilers. Several authors indicate that iron content is a significant indicator of the slagging propensity of a majority of US bituminous coals, in particular eastern bituminous coals. The pyritic iron content of these coals is shown to be a particularly relevant consideration. A series of investigations of iron release during combustion is reported for a suite of coals ranging in rank from lignite to low-volatile bituminous coal under combustion conditions ranging from oxidizing to inert. Experimental measurements are described in which, under selected conditions, major fractions of the iron in the coal are released within a 25 ms period immediately following coal devolatilization. Mechanistic interpretation of the data suggest that the iron is released as a consequence of oxygen attack on porous pyrrhotite particles. Experimental testing of the proposed mechanism reveals that the release is dependent on the presence of both pyrite in the raw coal and oxygen in the gas phase, that slow preoxidation (weathering) of the pyrite significantly inhibits the iron release, and that iron loss increases as oxygen penetration of the particle increases. Each observation is consistent with the postulated mechanism.

  1. Isotopic signature of atmospheric phosphate emitted from coal combustion

    NASA Astrophysics Data System (ADS)

    Weinberger, Roi; Weiner, Tal; Angert, Alon

    2016-07-01

    Atmospheric deposition of phosphorus (P) serves as an important nutrient input for many terrestrial, marine and freshwater ecosystems, influencing their biogeochemistry and primary production. Fossil fuel combustion, principally coal, is estimated to be a major source of atmospheric-P in industrialized regions. In this research, we aim to find a distinct isotopic signature for fly coal ash, the by-product of coal combustion that is emitted to the atmosphere. This signature could be used to identify coal's contribution to atmospheric-P. For this aim, ten fly coal ash samples from different coal sources, collected by power station filters, were analyzed for P concentrations and stable oxygen isotopic composition (δ18OP). Two inorganic phosphate fractions were analyzed: HCl-extractable and resin-extractable (bioavailable P). High HCl-P concentrations of up to 3500 μg P/g ash were found with a distinct δ18OP range of 17.1-20.5‰. The resin-P concentrations were substantially lower (<8 μg/g) with a wider and significantly lower δ18OP range of 10.6-16.5‰. The ash samples were found to have HCl-P δ18OP higher in ∼0-∼9‰ relative to the source coal. Similar isotopic values were found for ash with the same coal source country, regardless of the power station. Despite the low bioavailable P concentrations, fly ash could still be an important atmospheric P source to the biosphere since these combustion products likely acidify in the atmosphere to become bioavailable. This is also supported by our finding that smaller particles, which are more indicative of the particles actually emitted to the atmosphere, are significantly P-richer. Natural dust sources' δ18OP overlap fly ash's range, complicating the assessment of coal's contribution. Nonetheless, our results provide a new tool for identification of fossil fuel combustion sources in local and global atmospheric P deposition.

  2. Biomedically relevant chemical and physical properties of coal combustion products.

    PubMed Central

    Fisher, G L

    1983-01-01

    The evaluation of the potential public and occupational health hazards of developing and existing combustion processes requires a detailed understanding of the physical and chemical properties of effluents available for human and environmental exposures. These processes produce complex mixtures of gases and aerosols which may interact synergistically or antagonistically with biological systems. Because of the physicochemical complexity of the effluents, the biomedically relevant properties of these materials must be carefully assessed. Subsequent to release from combustion sources, environmental interactions further complicate assessment of the toxicity of combustion products. This report provides an overview of the biomedically relevant physical and chemical properties of coal fly ash. Coal fly ash is presented as a model complex mixture for health and safety evaluation of combustion processes. PMID:6337824

  3. Improved low NOx firing systems for pulverized coal combustion

    SciTech Connect

    McCarthy, K.; Laux, S.; Grusha, J.; Rosin, T.; Hausman, G.L.

    1999-07-01

    More stringent emission limits or the addition of post combustion NOx control create the need for improvements of NOx emissions from pulverized coal boilers. Many boilers retrofitted with Low NOx technology during Phase 1 and Phase 2 of the CAAA fail or marginally meet their requirements. Technical solutions range from addition of overfire air and state-of-the-art low NOx burners to low cost additions of combustion enhancements. Regardless of the combustion NOx control method used, stoichiometries local to the burners must be maintained at the designed values at all times to provide high NOx performance at low efficiency loss due to unburned fuel. This paper describes Foster Wheeler's approach to NOx emission improvements for existing low NOx firing systems. The technology to measure air and coal flow individually for each burner and to control the parameters for optimum combustion are presented and discussed. Field experience shows the installation and advantages of the technology.

  4. Combustion of coal gas fuels in a staged combustor

    NASA Technical Reports Server (NTRS)

    Rosfjord, T. J.; Mcvey, J. B.; Sederquist, R. A.; Schultz, D. F.

    1982-01-01

    Gaseous fuels produced from coal resources generally have heating values much lower than natural gas; the low heating value could result in unstable or inefficient combustion. Coal gas fuels may contain ammonia which if oxidized in an uncontrolled manner could result in unacceptable nitrogen oxide exhaust emission levels. Previous investigations indicate that staged, rich-lean combustion represents a desirable approach to achieve stable, efficient, low nitrogen oxide emission operation for coal-derived liquid fuels contaning up to 0.8-wt pct nitrogen. An experimental program was conducted to determine whether this fuel tolerance can be extended to include coal-derived gaseous fuels. The results of tests with three nitrogen-free fuels having heating values of 100, 250, and 350 Btu/scf and a 250 Btu/scf heating value doped to contain 0.7 pct ammonia are presented.

  5. Mutagenicity and carcinogenicity of car exhausts and coal combustion emissions

    SciTech Connect

    Holmberg, B.; Ahlbourg, U.

    1983-01-01

    Car exhausts and coal combustion emissions may cause a spectrum of health effects, varying from annoyance reactions, to bronchitis, to cancer in the respiratory organs and possibly also other organs. Deaths in cardiovascular diseases in particularly sensitive individuals have furthermore, under certain circumstances, been associated with ambient air pollution. The objective of the meeting was to examine the relevance of short-term and long-term biological tests for mutagenicity and carcinogenicity to the assessment of human carcinogenic risk that may arise from exposure to air pollution from motor vehicle exhausts and coal combustion products. (135 refs.)

  6. Coal desulfurization by chlorinolysis production and combustion test evaluation of product coals

    NASA Technical Reports Server (NTRS)

    Kalvinskas, J. J.; Daly, D.

    1982-01-01

    Laboratory-scale screening tests were carried out on coal from Harrison County, Ohio to establish chlorination and hydrodesulfurization conditions for the batch reactor production of chlorinolysis and chlorinolysis-hydrodesulfurized coals. In addition, three bituminous coals, were treated on the lab scale by the chlorinolysis process to provide 39 to 62% desulfurization. Two bituminous coals and one subbituminous coal were then produced in 11 to 15 pound lots as chlorinolysis and hydrodesulfurized coals. The chlorinolysis coals had a desulfurization of 29-69%, reductions in voltatiles and hydrogen. Hydrodesulfurization provided a much greater desulfurization (56-86%), reductions in volatiles and hydrogen. The three coals were combustion tested in the Penn State ""plane flame furnace'' to determine ignition and burning characteristics. All three coals burned well to completion as: raw coals, chlorinolysis processed coals, and hydrodesulfurized coals. The hydrodesulfurized coals experienced greater ignition delays and reduced burning rates than the other coals because of the reduced volatile content. It is thought that the increased open pore volume in the desulfurized-devolatilized coals compensates in part for the decreased volatiles effect on ignition and burning.

  7. Burning of suspended coal-water slurry droplet with oil as combustion additive

    SciTech Connect

    Yao, S.C.; Manwani, P.

    1986-10-01

    Coal-water slurries have been regarded as a potential substitute for heavy fuel oil. Various demonstrations of coal-water slurry combustion have been performed; however, a fundamental understanding of how the combustion process of a slurry fuel is enhanced is still not adequate. The combustion of coal-water mixture droplets suspended on microthermocouples has been investigated. It was found that droplets of lignite coal (which is a noncaking coal) burn effectively; however, droplets of bituminous coal (which is a caking coal) are relatively difficult to burn. During the heat-up of bituminous coal-water slurry droplets may turn to ''popcorn'' and show significant agglomeration. The incomplete combustion of coal-water slurry droplets in furnaces has been reported, and this is a drawback of this process. The objective of the present study is to explore the possibility of enhancing the combustion of coal-water slurry droplets with the use of a combustible emulsified oil.

  8. Coal combustion products 2007 production and use report

    SciTech Connect

    2009-07-01

    The American Coal Ash Association's 2007 Annual Coal Combustion Products (CCP) are derived from data from more than 170 power plants. The amount of CCPs used was 40.55%, a decrease of 2.88% from 2006, attributed to reduced fuel burn and a decrease in demand in the building industry. Figures are given for the production of fly ash, flue gas desulfurization gypsum, bottom ash, FBC ash and boiler slag. The article summarises results of the survey. 1 ref., 1 tab.

  9. Combustion characterization of the blend of plant coal and recovered coal fines

    SciTech Connect

    Singh, Shyam.

    1991-01-01

    The overall objective of this proposed research program is to determine the combustion characteristics of the blend derived from mixing a plant coal and recovered and clean coal fines from the pond. During this study, one plant coal and three blend samples will be prepared and utilized. The blend samples will be of a mixture of 90% plant coal + 10% fines, 85% plant coal + 15% fines, 80% plant coal + 20% fines having particle size distribution of 70% passing through {minus}200 mesh size. These samples' combustion behavior will be examined in two different furnaces at Penn State University, i.e., a down-fired furnace and a drop-tube furnace. The down-fired furnace will be used mainly to measure the emissions and ash deposition study, while the drop tube furnace will be used to determine burning profile, combustion efficiency, etc. This report covers the first quarter's progress. Major activities during this period were focused on finding the plants where a demo MTU column will be installed to prepare the samples needed to characterize the combustion behavior of slurry effluents. Also, a meeting was held at Penn State University to discuss the availability of the laboratory furnace for testing the plant coal/recovered coal fines blends.

  10. FATE OF COAL NITROGEN DURING COMBUSTION

    EPA Science Inventory

    The paper describes the burning of 21 coals, covering all ranks and under a wide variety of conditions, to ascertain the impact of coal properties on the fate of fuel nitrogen. Fuel NC was identified by using a nitrogen-free oxidant consisting of Ar/O2/CO2. It was found that fuel...

  11. NITRIC OXIDE FORMATION DURING PULVERIZED COAL COMBUSTION

    EPA Science Inventory

    Data on the overall conversion of coal-nitrogen to NOx were obtained at 1250 K and 1750 K for a residence time of one second. The conversion of coal-nitrogen to NOx decreased monotonically with increasing fuel/oxygen equivalence ratio and decreased slightly with increasing temper...

  12. Combustion of Illinois coals and chars with natural gas

    SciTech Connect

    Buckius, R.O.

    1991-01-01

    There are applications where the combined combustion of coal and natural gas offers potential advantages over the use of either coal or natural gas alone. For example, low volatile coals or low volatile chars derived from treatment or gasification processes can be of limited use during to their poor flammability characteristics. However, the use of natural gas in conjunction with the solid fuel can provide the necessary volatiles'' to enhance the combustion. In addition, natural gas provides a clean fuel source of fuel which, in cofiring situations, can extend the usefulness of coals with high sulfur content. The addition of natural gas may reduce SO{sub x} emission through increased sulfur retention in the ash and reduce NO{sub x} emissions by varying local stoichiometry and temperature levels. In this research program, studies of combined coal and natural gas combustion will provide particle ignition, burnout rates and ash characterization, that will help clarify the effect of coal and natural gas and identify the controlling parameters and mechanisms.

  13. CO2 emission of coal spontaneous combustion and its relation with coal microstructure, China.

    PubMed

    Wang, Haiyan; Chen Chen; Huang, Tao; Gao, Wei

    2015-07-01

    Coal spontaneous combustion is widely distributed all over the world. CO2 is the main greenhouse gas emitted by coal spontaneous combustion. In the present study characters of CO2 emitted by 10 typical Chinese coal spontaneous combustion and the influence of raw coal functional group on CO2 was studied. CO2 already exists under normal temperature as coal exposed in atmosphere. Under low temperature, the quality of CO2 released by coal spontaneous combustion is relatively small, but tends to increase. And corresponding with it, the oxygen consumption amount is also small. At medium temperature, the oxygen consumption increases rapidly and CO2 mass release rate begins to increase rapidly. Then, CO2 release rate increase rapidly under relatively high temperature (higher than 673 K). Over 873K, concentration of O2 is 6% and release rate of CO2 tends to be steady. It also concluded that mass ratio of CO to CO2 (CO/CO2) during coal spontaneous combustion was lowerthan 0.10 at low temperature. And then, it increased rapidly at medium temperature and reached to top at about 673 K. At 673-873 K, the ratio decreased again, and did not decrease evidently at about 873K. At temperature higher than 873K, the ratio was about 0.13. During the whole testing temperature range, CO/CO2 was not be higher than 0.26, lower than 0.2. This means that release rate of CO2 was much higher than CO during the whole process of coal spontaneous combustion. Moreover, the gas release quantity of CO2 is positively related with carbony content in raw coal. Carbonyl and carboxyl were both material basis of CO2. PMID:26364484

  14. Low-rank coal research: Volume 3, Combustion research: Final report. [Great Plains

    SciTech Connect

    Mann, M. D.; Hajicek, D. R.; Zobeck, B. J.; Kalmanovitch, D. P.; Potas, T. A.; Maas, D. J.; Malterer, T. J.; DeWall, R. A.; Miller, B. G.; Johnson, M. D.

    1987-04-01

    Volume III, Combustion Research, contains articles on fluidized bed combustion, advanced processes for low-rank coal slurry production, low-rank coal slurry combustion, heat engine utilization of low-rank coals, and Great Plains Gasification Plant. These articles have been entered individually into EDB and ERA. (LTN)

  15. STRUCTURE-BASED PREDICTIVE MODEL FOR COAL CHAR COMBUSTION

    SciTech Connect

    CHRISTOPHER M. HADAD; JOSEPH M. CALO; ROBERT H. ESSENHIGH; ROBERT H. HURT

    1999-01-13

    Significant progress continued to be made during the past reporting quarter on both major technical tasks. During the reporting period at OSU, computational investigations were conducted of addition vs. abstraction reactions of H, O(3 P), and OH with monocyclic aromatic hydrocarbons. The potential energy surface for more than 80 unique reactions of H, O ( 3 P), and OH with aromatic hydrocarbons were determined at the B3LYP/6-31G(d) level of theory. The calculated transition state barriers and reaction free energies indicate that the addition channel is preferred at 298K, but that the abstraction channel becomes dominant at high temperatures. The thermodynamic preference for reactivity with aromatic hydrocarbons increases in the order O(3 P) < H < OH. Abstraction from six-membered aromatic rings is more facile than abstraction from five-membered aromatic rings. However, addition to five-membered rings is thermodynamically more favorable than addition to six-membered rings. The free energies for the abstraction and addition reactions of H, O, and OH with aromatic hydrocarbons and the characteristics of the respective transition states can be used to calculate the reaction rate constants for these important combustion reactions. Experimental work at Brown University on the effect of reaction on the structural evolution of different chars (i.e., phenolic resin char and chars produced from three different coals) have been investigated in a TGA/TPD-MS system. It has been found that samples of different age of these chars appeared to lose their "memory" concerning their initial structures at high burn-offs. During the reporting period, thermal desorption experiments of selected samples were conducted. These spectra show that the population of low temperature oxygen surface complexes, which are primarily responsible for reactivity, are more similar for the high burn-off than for the low burn-off samples of different ages; i.e., the population of active sites are more

  16. Combustion of coal-gas fuels in a staged combustor

    SciTech Connect

    Rosfjord, T J; McVey, J B; Sederquist, R A; Schultz, D F

    1982-01-01

    Gaseous fuels produced from coal resources have been considered for use in industrial gas turbines. Such fuels generally have heating values much lower than the typical gaseous fuel, natural gas; the low heating value could result in unstable or inefficient combustion. Additionally, coal gas fuels may contain ammonia which if oxidized in an uncontrolled manner could result in unacceptable NO/sub x/ exhaust emission levels. Previous investigations have indicated that staged, rich-lean combustion represents a desirable approach to achieve stable, efficient, low NO/sub x/ emission operation for coal-derived liquid fuels containing up to 0.8-wt % nitrogen. An experimental program has been conducted to determine whether this fuel tolerance can be extended to include coal-derived gaseous fuels. The results of tests with three nitrogen-free fuels having heating values of 100, 250, and 350 Btu/scf and a 250 Btu/scf heating value doped to contain 0.7% ammonia are presented. The test results permit the following conclusions to be drawn: (1) Staged, rich-lean combustion represents the desirable approach to achieve ultra-low NO/sub x/ and CO emissions for coal gas fuels with heating values of 210 kJ/mol (238 Btu/scf) or higher. (2) Lean combustion represents the desirable approach to achieve ultra-low NO/sub x/ and CO emissions for coal gas fuels with low heating values (84 kJ/mol (95 Btu/scf)). (3) Staged combustion has the ability to limit NH/sub 3/ to NO/sub x/ conversion rates to less than 5%. NO/sub x/ emissions below the EPA limit can readily be achieved.

  17. Coal-feeding mechanism for a fluidized bed combustion chamber

    DOEpatents

    Gall, Robert L.

    1981-01-01

    The present invention is directed to a fuel-feeding mechanism for a fluidized bed combustor. In accordance with the present invention a perforated conveyor belt is utilized in place of the fixed grid normally disposed at the lower end of the fluidized bed combustion zone. The conveyor belt is fed with fuel, e.g. coal, at one end thereof so that the air passing through the perforations dislodges the coal from the belt and feeds the coal into the fluidized zone in a substantially uniform manner.

  18. Sequestration of carbon dioxide by indirect mineralization using Victorian brown coal fly ash.

    PubMed

    Sun, Yong; Parikh, Vinay; Zhang, Lian

    2012-03-30

    The use of an industry waste, brown coal fly ash collected from the Latrobe Valley, Victoria, Australia, has been tested for the post-combustion CO(2) capture through indirect minersalization in acetic acid leachate. Upon the initial leaching, the majority of calcium and magnesium in fly ash were dissolved into solution, the carbonation potential of which was investigated subsequently through the use of a continuously stirred high-pressure autoclave reactor and the characterization of carbonation precipitates by various facilities. A large CO(2) capture capacity of fly ash under mild conditions has been confirmed. The CO(2) was fixed in both carbonate precipitates and water-soluble bicarbonate, and the conversion between these two species was achievable at approximately 60°C and a CO(2) partial pressure above 3 bar. The kinetic analysis confirmed a fast reaction rate for the carbonation of the brown coal ash-derived leachate at a global activation energy of 12.7 kJ/mol. It is much lower than that for natural minerals and is also very close to the potassium carbonate/piperazine system. The CO(2) capture capacity of this system has also proven to reach maximum 264 kg CO(2)/ton fly ash which is comparable to the natural minerals tested in the literature. As the fly ash is a valueless waste and requires no comminution prior to use, the technology developed here is highly efficient and energy-saving, the resulting carbonate products of which are invaluable for the use as additive to cement and in the paper and pulp industry. PMID:22326240

  19. Combustion of coal/water mixtures with thermal preconditioning

    SciTech Connect

    Novack, M.; Roffe, G.; Miller, G.

    1987-07-01

    Thermal preconditioning is a process in which coal/water mixtures are vaporized to produce coal/steam suspensions, and then superheated to allow the coal to devolatilize producing suspensions of char particles in hydrocarbon gases and steam. This final product of the process can be injected without atomization, and burned directly in a gas turbine combustor. This paper reports on the results of an experimental program in which thermally preconditioned coal/water mixture was successfully burned with a stable flame in a gas turbine combustor test rig. Tests were performed at a mixture flowrate of 300 lb/hr and combustor pressure of 8 atm. The coal/water mixture was thermally preconditioned and injected into the combustor over a temperature range from 340/sup 0/F to 600/sup 0/F, and combustion air was supplied at between 600/sup 0/F to 725/sup 0/F. Test durations varied between 10 and 20 min. Major results of the combustion testing were that: A stable flame was maintained over a wide equivalence ratio range, between phi = 2.2 (rich) and 0.2 (lean); and combustion efficiency of over 99 percent was achieved when the mixture was preconditioned to 600/sup 0/F and the combustion air preheated to 725/sup 0/F. Measurements of ash particulates, captured in the exhaust sampling probe located 20 in. from the injector face, show typical sizes collected to be about 1 ..mu..m, with agglomerates of these particulates to be not more than 8 ..mu..m. The original mean coal particle size for these tests, prior to preconditioning, was 25 ..mu..m. Results of additional tests showed that one third of the sulfur contained in the solids of a coal/water mixture with 3 percent sulfur was evolved in gaseous form (under mild thermolized conditions) mainly as H/sub 2/S with the remainder as light mercaptans.

  20. Toxic substances form coal combustion--a co prehemsice assessment

    SciTech Connect

    Huggins, F.; Huffman, G.P.; Shah, N.

    1997-04-01

    The Clean Coal Act Amendments of 1990 identify a number of hazardous air pollutants as candidates for regulation. Should regulations be imposed on emission of these pollutants from coal-fired power plants, a sound understanding of the fundamental principles controlling their formation and partition will be needed. A new Toxics Partitioning Engineering Model (ToPEM) has been developed by a broad consortium to be useful to regulators and utility planners. During the last quarter coal analysis was completed on the final program coal, from the Wyodak Seam of the Powder River Basin, Combustion testing continued, including data collected on the self-sustained combustor. Efforts were directed to identify the governing mechanisms for trace element vaporization from the program coals. Mercury speciation and measurements were continued. Review of the existing trace element and organics emission literature was completed. And, model development was begun.

  1. PULVERIZED COAL COMBUSTION: POLLUTANT FORMATION AND CONTROL, 1970-1980

    EPA Science Inventory

    The report documents the support role of EPA's Air and Energy Engineering Research Laboratory in the major research effort directed by EPA in the l970s to understand pollutant formation during pulverized coal combustion (PCC). nderstanding the conversion of fuel nitrogen to nitro...

  2. PULVERIZED COAL COMBUSTION: POLLUTANT FORMATION AND CONTROL, 1970-1980

    EPA Science Inventory

    The report documents the support role of EPA's Air and Energy Engineering Research Laboratory in the major research effort directed by EPA in the l970s to understand pollutant formation during pulverized coal combustion (PCC). Understanding the conversion of fuel nitrogen to nit...

  3. Combustion characteristics and arsenic retention during co-combustion of agricultural biomass and bituminous coal.

    PubMed

    Zhou, Chuncai; Liu, Guijian; Wang, Xudong; Qi, Cuicui; Hu, Yunhu

    2016-08-01

    A combination of thermogravimetric analysis (TG) and laboratory-scale circulated fluidized bed combustion experiment was conducted to investigate the thermochemical, kinetic and arsenic retention behavior during co-combustion bituminous coal with typical agricultural biomass. Results shown that ignition performance and thermal reactivity of coal could be enhanced by adding biomass in suitable proportion. Arsenic was enriched in fly ash and associated with fine particles during combustion of coal/biomass blends. The emission of arsenic decreased with increasing proportion of biomass in blends. The retention of arsenic may be attributed to the interaction between arsenic and fly ash components. The positive correlation between calcium content and arsenic concentration in ash suggesting that the arsenic-calcium interaction may be regarded as the primary mechanism for arsenic retention. PMID:27136608

  4. Control of Trace Metal Emissions During Coal Combustion

    SciTech Connect

    Thomas C. Ho

    1996-10-01

    Emissions of toxic trace metals in the form of metal fumes or submicron particulate from a coal-fired combustion source have received greater environmental and regulatory concern over the past years. Current practice of controlling these emissions is to collect them at the cold-end of the process by air-pollution control devices (APCDS) such as electrostatic precipitators and baghouses. However, trace metal fumes may not always be effectively collected by these devices because the formed fumes are extremely small. The proposed research is to explore the opportunities for improved control of toxic trace metal emissions, alternatively, at the hot-end of the coal combustion process, i.e., in the combustion chamber. The technology proposed is to prevent the metal fumes from forming during the process, which would effectively eliminate the metal emission problems. Specifically, the technology is to employ suitable sorbents to (1) reduce the amount of metal volatilization during combustion and (2) capture volatilized metal vapors. The objectives of the project are to demonstrate the technology and to characterize the metal capture process during coal combustion in a fluidized bed combustor.

  5. Control of Trace Metal Emissions During Coal Combustion

    SciTech Connect

    Thomas C. Ho

    1997-10-01

    Emissions of toxic trace metals in the form of metal fumes or submicron particulates from a coal-fired combustion source have received greater environmental and regulatory concern over the past years. Current practice of controlling these emissions is to collect them at the cold-end of the process by air-pollution control devices (APCDs) such as electrostatic precipitators and baghouses. However, trace metal fumes may not always be effectively collected by these devices because the formed fumes are extremely small. The proposed research is to explore the opportunities for improved control of toxic trace metal emissions, alternatively, at the hot-end of the coal combustion process, i.e., in the combustion chamber. The technology proposed is to prevent the metal fumes from forming during the process, which would effectively eliminate the metal emission problems. Specifically, the technology is to employ suitable sorbents to (1) reduce the amount of metal volatilization during combustion and (2) capture volatilized metal vapors. The objectives of the project are to demonstrate the technology and to characterize the metal capture process during coal combustion in a fluidized bed combustor. The project was started on July 1, 1994 and this is the thirteenth quarterly technical progress report. Specifically, the following progress has been made during this performance period from July 1, 1997 through September 30, 1997.

  6. Control of Trace Metal Emissions During Coal Combustion

    SciTech Connect

    Thomas C. Ho

    1997-01-01

    Emissions of toxic trace metals in the form of metal fumes or submicron particulates from a coal-fired combustion source have received greater environmental and regulatory concern over the past years. Current practice of controlling these emissions is to collect them at the cold-end of the process by air-pollution control devices (APCDs) such as electrostatic precipitators and baghouses. However, trace metal fumes may not always be effectively collected by these devices because the formed fumes are extremely small. The proposed research is to explore the opportunities for improved control of toxic trace metal emissions, alternatively, at the hot-end of the coal combustion process, i.e., in the combustion chamber. The technology proposed is to prevent the metal fumes from forming during the process, which would effectively eliminate the metal emission problems. Specifically, the technology is to employ suitable sorbents to (1) reduce the amount of metal volatilization during combustion and (2) capture volatilized metal vapors. The objectives of the project are to demonstrate the technology and to characterize the metal capture process during coal combustion in a fluidized bed combustor.

  7. Control of Trace Metal Emissions During Coal Combustion

    SciTech Connect

    Thomas C. Ho

    1997-07-01

    Emissions of toxic trace metals in the form of metal fumes or submicron particulates from a coal-fired combustion source have received greater environmental and regulatory concern over the past years. Current practice of controlling these emissions is to collect them at the cold-end of the process by air-pollution control devices (APCDs) such as electrostatic precipitators and baghouses. However, trace metal fumes may not always be effectively collected by these devices because the formed fumes are extremely small. The proposed research is to explore the opportunities for improved control of toxic trace metal emissions, alternatively, at the hot-end of the coal combustion process, i.e., in the combustion chamber. The technology proposed is to prevent the metal fumes from forming during the process, which would effectively eliminate the metal emission problems. Specifically, the technology is to employ suitable sorbents to (1) reduce the amount of metal volatilization during combustion and (2) capture volatilized metal vapors. The objectives of the project are to demonstrate the technology and to characterize the metal capture process during coal combustion in a fluidized bed combustor.

  8. Control of Trace Metal Emissions During Coal Combustion

    SciTech Connect

    Thomas C. Ho

    1997-04-01

    Emissions of toxic trace metals in the form of metal fumes or submicron particulates from a coal-fired combustion source have received greater environmental and regulatory concern over the past years. Current practice of controlling these emissions is to collect them at the cold-end of the process by air-pollution control devices (APCDs) such as electrostatic precipitators and baghouses. However, trace metal fumes may not always be effectively collected by these devices because the formed fumes are extremely small. The proposed research is to explore the opportunities for improved control of toxic trace metal emissions, alternatively, at the hot-end of the coal combustion process, i.e., in the combustion chamber. The technology proposed is to prevent the metal fumes from forming during the process, which would effectively eliminate the metal emission problems. Specifically, the technology is to employ suitable sorbents to (1) reduce the amount of metal volatilization during combustion and (2) capture volatilized metal vapors. The objectives of the project are to demonstrate the technology and to characterize the metal capture process during coal combustion in a fluidized bed combustor.

  9. Mercury emissions and species during combustion of coal and waste

    SciTech Connect

    Hong Yao; Guangqian Luo; Minghou Xu; Tamotsu Kameshima; Ichiro Naruse

    2006-10-15

    The behaviors of mercury evolution for three types of coal and three types of dried sewage sludge are studied using a thermogravimetric (TG) analyzer. The mercury speciations in the flue gas from coal and sludge combustion are also analyzed by implementing a horizontal electrically heated tube furnace. Furthermore, the kinetic calculations of mercury oxidizing processes are carried out using the software package CHEMKIN in order to interpret the homogeneous mechanism of mercury oxidization. The results obtained show that the sulfur content in the sludge inhibits the evolution of mercury at low temperature if the Cl concentration is high enough. Chlorine enhances mercury evolution in the coal combustion, whereas there is no relationship when the Cl concentration is high. Fixed carbon content plays a role in depression of the mercury evolution. Formation of oxidized mercury (HgCl{sub 2}) does not relate to the chlorine concentration in the raw coal and sludge. Whereas the ash and sulfur content in the sludge affects the Hg oxidization, kinetic calculations show that HgCl, Cl{sub 2}, and HOCl formation is important in producing the oxidized mercury during combustion of coal and sludge at 873 K. A suitable temperature for Hg oxidization when Cl{sub 2} is the oxidization resource is 700-1200 K. 32 refs., 10 figs., 5 tabs.

  10. Preparation of nitrogen-enriched activated carbons from brown coal

    SciTech Connect

    Robert Pietrzak; Helena Wachowska; Piotr Nowicki

    2006-05-15

    Nitrogen-enriched activated carbons were prepared from a Polish brown coal. Nitrogen was introduced from urea at 350{sup o}C in an oxidizing atmosphere both to carbonizates obtained at 500-700{sup o}C and to activated carbons prepared from them. The activation was performed at 800{sup o}C with KOH in argon. It has been observed that the carbonization temperature determines the amount of nitrogen that is incorporated (DC5U, 8.4 wt % N{sup daf}; DC6U, 6.3 wt % N{sup daf}; and DC7U, 5.4 wt % N{sup daf}). X-ray photoelectron spectroscopy (XPS) measurements have shown that nitrogen introduced both at the stage of carbonizates and at the stage of activated carbons occurs mainly as -6, -5, and imine, amine and amide groups. On the other hand, the activation of carbons enriched with nitrogen results in the formation of pyridonic nitrogen and N-Q. The introduction of nitrogen at the activated carbon stage leads to a slight decrease in surface area. It has been proven that the most effective way of preparing microporous activated carbons enriched with nitrogen to a considerable extent and having high surface area ({approximately} 3000 m{sup 2}/g) is the following: carbonization - activation - reaction with urea. 40 refs., 1 fig., 6 tabs.

  11. Method for increasing the calorific value of gas produced by the in situ combustion of coal

    DOEpatents

    Shuck, Lowell Z.

    1978-01-01

    The present invention relates to the production of relatively high Btu gas by the in situ combustion of subterranean coal. The coal bed is penetrated with a horizontally-extending borehole and combustion is initiated in the coal bed contiguous to the borehole. The absolute pressure within the resulting combustion zone is then regulated at a desired value near the pore pressure within the coal bed so that selected quantities of water naturally present in the coal will flow into the combustion zone to effect a hydrogen and carbon monoxide-producing steam-carbon reaction with the hot carbon in the combustion zone for increasing the calorific value of the product gas.

  12. Electricity from coal and utilization of coal combustion by-products

    SciTech Connect

    Demirbas, A.

    2008-07-01

    Most electricity in the world is conventionally generated using coal, oil, natural gas, nuclear energy, or hydropower. Due to environmental concerns, there is a growing interest in alternative energy sources for heat and electricity production. The major by-products obtained from coal combustion are fly ash, bottom ash, boiler slag, and flue gas desulfurization (FGD) materials. The solid wastes produced in coal-fired power plants create problems for both power-generating industries and environmentalists. The coal fly ash and bottom ash samples may be used as cementitious materials.

  13. Plasma Torch for Plasma Ignition and Combustion of Coal

    NASA Astrophysics Data System (ADS)

    Ustimenko, Alexandr; Messerle, Vladimir

    2015-09-01

    Plasma-fuel systems (PFS) have been developed to improve coal combustion efficiency. PFS is a pulverized coal burner equipped with arc plasma torch producing high temperature air stream of 4000 - 6000 K. Plasma activation of coal at the PFS increases the coal reactivity and provides more effective ignition and ecologically friendly incineration of low-rank coal. The main and crucial element of PFS is plasma torch. Simplicity and reliability of the industrial arc plasma torches using cylindrical copper cathode and air as plasma forming gas predestined their application at heat and power engineering for plasma aided coal combustion. Life time of these plasma torches electrodes is critical and usually limited to 200 hours. Considered in this report direct current arc plasma torch has the cathode life significantly exceeded 1000 hours. To ensure the electrodes long life the process of hydrocarbon gas dissociation in the electric arc discharge is used. In accordance to this method atoms and ions of carbon from near-electrode plasma deposit on the active surface of the electrodes and form electrode carbon condensate which operates as ``actual'' electrode. Complex physicochemical investigation showed that deposit consists of nanocarbon material.

  14. Laser diagnostics of mineral matter and combustion processes in coal

    SciTech Connect

    Venkateswarlu, P.; George, M.C.; Sekhar, P.C.; Subbarao, V.

    1989-01-01

    This is the third report on this project. During the period covered by the first two reports (October 1, 1987 through August 30, 1988) a sample of low sulfur powdered coal was heated under vacuum from 25 to 1000{degrees}C at a heating rate of 5{degrees}C per minute. The vapors generated were analyzed by a Balzer Quadrupole Mass Spectrometer model QMG 511. The analysis showed that the major constituents of the vapors are aliphatic hydrocarbons. A second set of experiments were carried out to determine the mineral constituents in ash obtained by heating coal in a porcelain crucible at 400--500{degrees}C in a muffle furnace until all the coal was oxidized. Model 3030 Perkin Elmer Atomic Absorption Spectrophotometer was used with appropriate hollow cathode lamps. A dozen elements were identified. Al, Na, K and Fe were the most prominent. During this period we have made an extensive series of measurements on laser induced combustion of coal pellets made from coal powder. C{sub 2}, CN, CO, Na and K were identified from the spectra. We have also fabricated a burner for the study of coal combustion using laser spectroscopic techniques. 1 ref., 4 figs.

  15. Toxic Substances From Coal Combustion - Phase I Coal Selection and Chaacterization

    SciTech Connect

    A. Kolker; A. Sarofim; C.A. Palmer; C.L. Senior; F.E. Huggins; G.P. Huffman; I. Olmez; N. Shah; R. Finkelman; S. Crowley; T. Zeng

    1998-07-16

    The Clean Air Act Amendments of 1990 identify a number of hazardous air pollutants (HAPs) as candidates for regulation. Should regulations be imposed on HAP emissions from coal-fired power plants, a sound understanding of the fundamental principles controlling the formation and partitioning of toxic species during coal combustion will be needed. Over the past decade, a large database identifying the partitioning and emitted concentrations of several toxic metals on the list of HAPs has been developed. Laboratory data have also been generated to help define the general behavior of several elements in combustion systems. These data have been used to develop empirical and probabalistic models to predict emissions of trace metals from coal-fired power plants. While useful for providing average emissions of toxic species, these empirically based models fail when extrapolated beyond their supporting database. This represents a critical gap; over the coming decades, new fuels and combustion systems will play an increasing role in our nation's power generation system. For example, new fuels, such as coal blends or beneficiated fuels, new operating conditions, such as low-NO burners or staged combustion, or new power x systems, for example, those being developed under the DoE sponsored Combustion 2000 programs and integrated gasification combined cycle (IGCC) systems, are all expected to play a role in power generation in the next century. The need for new predictive tools is not limited to new combustion systems, however. Existing combustion systems may have to employ controls for HAPs, should regulations be imposed. Testing of new control methods, at pilot and full scale, is expensive. A sound under-standing of the chemical transformations of both organic and inorganic HAPs will promote the development of new control methods in a cost-effective manner. To ensure that coal-fired power generation proceeds in an environmentally benign fashion, methods for the prediction and

  16. [Lead emission amount from coal combustion and its environment effect in Xi'an City].

    PubMed

    Luo, Kunli; Wang, Douhu; Tan, Jianan; Wang, Lizheng; Feng, Fujian; Li, Ribang

    2002-01-30

    For study the lead emission amount from coal combustion and its environment effect, the lead content of coal, ash and cinder of power station and coal-fired boiler, the lead content of dusts in the period of heating time and the non-heating time in Xi'an City were studied in this paper. The results show that amount of lead emission from 1 ton coal combustion, which lead content in coal was 30 g, was 20 g in atmosphere. The rate of lead emission of coal combustion was about 66%. About 10 million tons of coal was straight burning every year in Xi'an City and suburb, those coal mainly come from Permo-Carboniferous coal in Weibei coal mine, Shaanxi, their average lead content was 30 mg/kg. So the total lead emission from coal combustion to atmosphere was about 200 t annually in Xi'an City. PMID:11987396

  17. Formation and use of coal combustion residues from three types of power plants burning Illinois coals

    USGS Publications Warehouse

    Demir, I.; Hughes, R.E.; DeMaris, P.J.

    2001-01-01

    Coal, ash, and limestone samples from a fluidized bed combustion (FBC) plant, a pulverized coal combustion (PC) plant, and a cyclone (CYC) plant in Illinois were analyzed to determine the combustion behavior of mineral matter, and to propose beneficial uses for the power plant ashes. Pyrite and marcasite in coal were converted during combustion to glass, hematite and magnetite. Calcite was converted to lime and anhydrite. The clay minerals were altered to mullite and glass. Quartz was partially altered to glass. Trace elements in coal were partially mobilized during combustion and, as a result, emitted into the atmosphere or adsorbed on fly ash or on hardware on the cool side of the power plants. Overall, the mobilities of 15 trace elements investigated were lower at the FBC plant than at the other plants. Only F and Mn at the FBC plant, F, Hg, and Se at the PC plant and Be, F, Hg, and Se at the CYC plant had over 50% of their concentrations mobilized. Se and Ge could be commercially recovered from some of the combustion ashes. The FBC ashes could be used as acid neutralizing agents in agriculture and waste treatment, and to produce sulfate fertilizers, gypsum wall boards, concrete, and cement. The PC and CYC fly ashes can potentially be used in the production of cement, concrete, ceramics, and zeolites. The PC and CYC bottom ashes could be used in stabilized road bases, as frits in roof shingles, and perhaps in manufacturing amber glass. ?? 2001 Elsevier Science Ltd. All rights reserved.

  18. [Study on the calcium-based sorbent for removal fluorine during coal combustion].

    PubMed

    Li, Shu-ling; Qi, Qing-jie; Liu, Jian-zhong; Cao, Xin-yu; Zhou, Jun-hu; Cen, Ke-fa

    2004-03-01

    In the paper, the reaction of CaO-HF and fluorine removal mechanics at high temperature by blending calcium-based sorbents with coal during coal combustion were discussed, and test results about fluorine retention during coal combustion in fluidized bed and chain-grate furnace were reported. The results identified that lime and calcium-based sorbets developed can restratin the emission of fluorine during coal combustion. The efficiency of fluorine removal can reach 66.7%-70.0% at Ca/F 60-70 by blending lime with coal in fluidized bed combustion, and the efficiency of fluorine removal are between 57.32% and 75.19% by blending calcium-based sorbets with coal in chain-grate furnace combustion. Blending CaO or lime with coal during coal combustion can remove SO2 and HF simultaneously. PMID:15202259

  19. CHARACTERISTICS OF SINGLE PARTICLE COAL COMBUSTION

    EPA Science Inventory

    The paper discusses the measurement of the burning history of single coal particles, using a two-color optical pyrometer. rom intensity traces at two wavelengths, information on burning times and temperatures, the duration of a volatile flame, and projected areas was obtained for...

  20. Oxy-combustion of pulverized coal : modeling of char-combustion kinetics.

    SciTech Connect

    Shaddix, Christopher R.; Haynes, Brian S.; Geier, Manfred

    2010-09-01

    In this study, char combustion of pulverized coal under oxy-fuel combustion conditions was investigated on the basis of experimentally observed temperature-size characteristics and corresponding predictions of numerical simulations. Using a combustion-driven entrained flow reactor equipped with an optical particle-sizing pyrometer, combustion characteristics (particle temperatures and apparent size) of pulverized coal char particles was determined for combustion in both reduced oxygen and oxygen-enriched atmospheres with either a N{sub 2} or CO{sub 2} bath gas. The two coals investigated were a low-sulfur, high-volatile bituminous coal (Utah Skyline) and a low-sulfur subbituminous coal (North Antelope), both size-classified to 75-106 {micro}m. A particular focus of this study lies in the analysis of the predictive modeling capabilities of simplified models that capture char combustion characteristics but exhibit the lowest possible complexity and thus facilitate incorporation in existing computational fluid dynamics (CFD) simulation codes. For this purpose, char consumption characteristics were calculated for char particles in the size range 10-200 {micro}m using (1) single-film, apparent kinetic models with a chemically 'frozen' boundary layer, and (2) a reacting porous particle model with detailed gas-phase kinetics and three separate heterogeneous reaction mechanisms of char-oxidation and gasification. A comparison of model results with experimental data suggests that single-film models with reaction orders between 0.5 and 1 with respect to the surface oxygen partial pressure may be capable of adequately predicting the temperature-size characteristics of char consumption, provided heterogeneous (steam and CO{sub 2}) gasification reactions are accounted for.

  1. Oxy-combustion of pulverized coal : modeling of char combustion kinetics.

    SciTech Connect

    Shaddix, Christopher R.; Haynes, Brian S.; Geier, Manfred

    2010-09-01

    In this study, char combustion of pulverized coal under oxy-fuel combustion conditions was investigated on the basis of experimentally observed temperature-size characteristics and corresponding predictions of numerical simulations. Using a combustion-driven entrained flow reactor equipped with an optical particle-sizing pyrometer, combustion characteristics (particle temperatures and apparent size) of pulverized coal char particles was determined for combustion in both reduced oxygen and oxygen-enriched atmospheres with either a N{sub 2} or CO{sub 2} bath gas. The two coals investigated were a low-sulfur, high-volatile bituminous coal (Utah Skyline) and a low-sulfur subbituminous coal (North Antelope), both size-classified to 75-106 {micro}m. A particular focus of this study lies in the analysis of the predictive modeling capabilities of simplified models that capture char combustion characteristics but exhibit the lowest possible complexity and thus facilitate incorporation in existing computational fluid dynamics (CFD) simulation codes. For this purpose, char consumption characteristics were calculated for char particles in the size range 10-200 {micro}m using (1) single-film, apparent kinetic models with a chemically 'frozen' boundary layer, and (2) a reacting porous particle model with detailed gas-phase kinetics and three separate heterogeneous reaction mechanisms of char-oxidation and gasification. A comparison of model results with experimental data suggests that single-film models with reaction orders between 0.5 and 1 with respect to the surface oxygen partial pressure may be capable of adequately predicting the temperature-size characteristics of char consumption, provided heterogeneous (steam and CO{sub 2}) gasification reactions are accounted for.

  2. Influence of sulfur in coals on char morphology and combustion

    SciTech Connect

    Marsh, H.

    1991-01-01

    During coal carbonization (pyrolysis), as during the combustion process of pulverized coal in a combustor, not all of the sulfur is released. Significant proportions become pat of the structure of the resultant coke and char. The combustion process of the char within the flames of the combustor in influenced dominantly by char morphology. This, in turn, controls the accessibility of oxidizing gases to the surfaces of the carbonaceous substance of the char. Mineral matter content, its extent and state of distribution, also exerts an influence on char morphology created during pyrolysis/carbonization. This complexity of coal renders it a very difficult material to study, systematically, to distinguish and separate out the contributing factors which influence combustion characteristics. Therefore, in such circumstances, it is necessary to simplify the systems by making use of model chars/cokes/carbons which can be made progressively more complex, but in a controlled way. In this way complicating influence in chars from coals can be eliminated, so enabling specific influences to be studied independently. It is important to note that preliminary work by Marsh and Gryglewicz (1990) indicated that levels of sulfur of about 3 to 5 wt % can reduce reactivities by 10 to 25%. The overall purpose of the study is to provide meaningful kinetic data to establish, quantitatively, the influence of organically-bound sulfur on the reactivity of carbons, and to ascertain if gasification catalysts are effective in the preferential removal of sulfur from the chars.

  3. Transformations of inorganic coal constituents in combustion systems

    SciTech Connect

    Helble, J.J.; Srinivasachar, S.; Wilemski, G.; Boni, A.A. ); Kang, Shin-Gyoo; Sarofim, A.F.; Graham, K.A.; Beer, J.M. ); Peterson, T.W.; Wendt, J.O.L.; Gallagher, N.B.; Bool, L. ); Huggins, F.E.; Huffman, G.P.; Shah, N.; Shah, A. (Kentucky Univ., Lexingt

    1992-11-01

    The inorganic constituents or ash contained in pulverized coal significantly increase the environmental and economic costs of coal utilization. For example, ash particles produced during combustion may deposit on heat transfer surfaces, decreasing heat transfer rates and increasing maintenance costs. The minimization of particulate emissions often requires the installation of cleanup devices such as electrostatic precipitators, also adding to the expense of coal utilization. Despite these costly problems, a comprehensive assessment of the ash formation and had never been attempted. At the start of this program, it was hypothesized that ash deposition and ash particle emissions both depended upon the size and chemical composition of individual ash particles. Questions such as: What determines the size of individual ash particles What determines their composition Whether or not particles deposit How combustion conditions, including reactor size, affect these processes remained to be answered. In this 6-year multidisciplinary study, these issues were addressed in detail. The ambitious overall goal was the development of a comprehensive model to predict the size and chemical composition distributions of ash produced during pulverized coal combustion. Results are described.

  4. Combustion characterization of beneficiated coal-based fuels

    SciTech Connect

    Chow, O.K.; Nsakala, N.Y.

    1990-08-01

    The objectives of this project include: (1) the development of an engineering data base which will provide detailed information on the properties of BCFs influencing combustion, ash deposition, ash erosion, particulate collection, and emissions; and (2) the application of this technical data base to predict the performance and economic impacts of firing the BCFs in various commercial boiler designs. The technical approach used to develop the technical data includes: bench-scale fuel property, conbustion, and ash deposition tests; pilot-scale combustion and ash effects tests; and full-scale combustion tests. Subcontractors to CE to perform parts of the test work are the Massachusetts Institute of Technology (MIT), Physical Sciences, Inc. Technology Company (PSIT) and the University of North Dakota Energy and Environmental Research Center (UNDEERC). Twenty fuels will be characterized during the three-year base program: three feed coals, fifteen BCFs, and two conventionally cleaned coals for the full-scale tests. Approximately nine BCFs will be in dry ultra-fine coal (DUC) form, and six BCFs will be in coal-water fuel (CWF) form. Additional BCFs would be characterized during optional project supplements.

  5. A new approach to precious metals recovery from brown coals: Correlation of recovery efficacy with the mechanism of metal-humic interactions

    NASA Astrophysics Data System (ADS)

    Bratskaya, Svetlana Yu.; Volk, Alexandra S.; Ivanov, Vladimir V.; Ustinov, Alexander Yu.; Barinov, Nikolay N.; Avramenko, Valentin A.

    2009-06-01

    The presence of gold and platinum group elements (PGE) in low-rank brown coals around the world has promoted interest in the industrial exploitation of this alternative source of precious metals. However, due to low efficacy of the methods traditionally used for the processing of mineral ores, there exists a high demand for new strategies of precious metal recovery from refractory carbonaceous materials that could significantly increase the economic potential of gold- and PGE-bearing organic resources. Here we discuss the possibility of gold and PGE recovery from alkaline extracts of brown coals using the difference in colloidal stability of bulk organic matter and its fractions enriched with precious metals. This approach enables one to avoid complete oxidation or combustion of brown coals prior to gold recovery, to minimize organic content in gold concentrate, and to obtain a valuable by-product - humic extracts. Using gold-bearing brown coals from several deposits located in the South Far East of Russia, we show that up to 95% of gold can be transferred to alkaline extracts of humic acids (HA) and up to 85% of this gold can be recovered by centrifugation at pH 4.0-6.0, when only 5-15% of HA precipitated simultaneously. We have shown that the high efficacy of gold recovery can be attributed to the occurrence of fine-dispersed elemental gold particles stabilized by HA, which differ significantly in colloidal stability from the bulk organic matter and, thus, can be separated by centrifugation.

  6. TOXIC SUBSTANCES FROM COAL COMBUSTION: A COMPREHENSIVE ASSESSMENT

    SciTech Connect

    C.L. Senior; T. Panagiotou; J.O.L. Wendt; W. Seames; F.E. Huggins; G.P Huffman; N. Yap; M.R. Ames; I.Olmez; T. Zeng; A.F. Sarofim; A. Kolker; R. Finkelman; J.J. Helble

    1998-07-16

    The Clean Air Act Amendments of 1990 identify a number of hazardous air pollutants (HAPs) as candidates for regulation. Should regulations be imposed on HAP emissions from coal-fired power plants, a sound understanding of the fundamental principles controlling the formation and partitioning of toxic species during coal combustion will be needed. With support from the Federal Energy Technology Center (FETC), the Electric Power Research Institute, and VTT (Finland), Physical Sciences Inc. (PSI) has teamed with researchers from USGS, the Massachusetts Institute of Technology (MIT), the University of Arizona (UA), the University of Kentucky (UK), the University of Connecticut (UC), the University of Utah (W) and the University of North Dakota Energy and Environmental Research Center (EERC) to develop a broadly applicable emissions model useful to regulators and utility planners. The new Toxics Partitioning Engineering Model (ToPEM) will be applicable to all combustion conditions including new fuels and coal blends, low-NO{sub x} combustion systems, and new power generation plants. Development of ToPEM will be based on PSI's existing Engineering Model for Ash Formation (EMAF). This report covers the reporting period from the submission of the draft Phase 1 Final Report through the end of June, 1998. During this period two of the three Phase 2 coals were procured and pulverized samples were distributed to team members. Analysis of Phase 1 X-Ray Absorption Fine Structure (XAFS) data, particularly of mercury in sorbent samples, continued. An improved method for identifying mercury compounds on sorbents was developed, leading to a clearer understanding of forms of mercury in char and sorbents exposed to flue gas. Additional analysis of Phase 1 large scale combustion data was performed to investigate mechanistic information related to the fate of the radionuclides Cs, Th, and Co. Modeling work for this period was focused on building and testing a sub-model for vaporization

  7. Coal-water slurry fuel internal combustion engine and method for operating same

    DOEpatents

    McMillian, Michael H.

    1992-01-01

    An internal combustion engine fueled with a coal-water slurry is described. About 90 percent of the coal-water slurry charge utilized in the power cycle of the engine is directly injected into the main combustion chamber where it is ignited by a hot stream of combustion gases discharged from a pilot combustion chamber of a size less than about 10 percent of the total clearance volume of main combustion chamber with the piston at top dead center. The stream of hot combustion gases is provided by injecting less than about 10 percent of the total coal-water slurry charge into the pilot combustion chamber and using a portion of the air from the main combustion chamber that has been heated by the walls defining the pilot combustion chamber as the ignition source for the coal-water slurry injected into the pilot combustion chamber.

  8. Toxic substances from coal combustion -- A comprehensive assessment

    SciTech Connect

    Senior, C.L.; Panagiotou, T.; Huggins, F.E.; Huffman, G.P.; Yap, N.; Wendt, J.O.L.; Seames, W.; Ames, M.R.; Sarofim, A.F.; Lighty, J.; Kolker, A.; Finkelman, R.; Palmer, C.A.; Mroczkowsky, S.J.; Helble, J.J.; Mamani-Paco, R.

    1999-07-30

    The Clean Air Act Amendments of 1990 identify a number of hazardous air pollutants (HAPs) as candidates for regulation. Should regulations be imposed on HAP emissions from coal-fired power plants, a sound understanding of the fundamental principles controlling the formation and partitioning of toxic species during coal combustion will be needed. With support from the Federal Energy Technology Center (FETC), the Electric Power Research Institute, and VTT (Finland), Physical Sciences Inc. (PSI) has teamed with researchers from USGS, MIT, the University of Arizona (UA), the University of Kentucky (UK), the University of Connecticut (UC), the University of Utah (UU) and the University of North Dakota Energy and Environmental Research Center (EERC) to develop a broadly applicable emissions model useful to regulators and utility planners. The new Toxics Partitioning Engineering Model (ToPEM) will be applicable to all combustion conditions including new fuels and coal blends, low-NOx combustion systems, and new power generation plants. Development of ToPEM will be based on PSI's existing Engineering Model for Ash Formation (EMAF). This report covers the period from 1 April 1999 to 30 June 1999. During this quarter low temperature ashing and elemental analysis of the three Phase II coals were completed. Results from MIT and USGS are comparable. Plans were made for measurements of loss of trace elements during devolatilization and for single particle combustion studies at the University of Utah. The iodated charcoal trap was tested on coal combustion flue gas and was shown to collect both Hg and Se in from the vapor phase with 100% efficiency. Data from the University of Arizona self-sustained combustor were analyzed from the combustion of three coals: Ohio, Wyodak and Illinois No. 6. Ash size distributions and enrichment factors for selected trace elements were calculated. The correlation between the concentration of the more volatile trace elements in the ash and the

  9. TOXIC SUBSTANCES FROM COAL COMBUSTION A COMPREHENSIVE ASSESSMENT

    SciTech Connect

    A KOLKER; AF SAROFIM; CA PALMER; FE HUGGINS; GP HUFFMAN; J LIGHTY; JJ HELBLE; JOL WENDT; MR AMES; N YAP; R FINKELMAN; R. MAMANI-PACO; SJ MROCZKOWSKY; T PANAGIOTOU; W SEAMES

    1999-01-28

    The technical objectives of this project are: (a) To identify the effect of the mode-of-occurrence of toxic elements in coal on the partitioning of these elements among vapor, submicron fume, and fly ash during the combustion of pulverized coal, (b) To identify the mechanisms governing the post-vaporization interaction of toxic elements and major minerals or unburnt char, (c) To determine the effect of combustion environment (i.e., fuel rich or fuel lean) on the partitioning of trace elements among vapor, submicron fume, and fly ash during the combustion of pulverized coal, (d) To model the partitioning of toxic elements among various chemical species in the vapor phase and between the vapor phase and complex aluminosilicate melts, (e) To develop the new Toxics Partitioning Engineering Model (ToPEM), applicable to all combustion conditions including new fuels and coal blends, low-NO{sub x} combustion systems, and new power generation plants. A description of the work plan for accomplishing these objectives is presented in Section 2.1 of this report. The work discussed in this report covers the reporting period from 1 October 1998 to 31 December 1998. During this quarter, basic coal testing at USGS was completed. Total sulfur contents range from 0.43 wt-% in the Wyodak to 2.68 wt-% in the Ohio sample. In the North Dakota and Ohio samples, about half of the total sulfur is pyritic and half is organic. The North Dakota sample also contains a minor amount of sulfate, consistent with the presence of barite in this sample. In the Wyodak sample, the majority of the sulfur is organic. Preliminary mineralogy of the three Phase II coals was determined by SEM/EDX. The Ohio coal contains all of the five most common major phases: quartz, illitic clay, kaolinitic clay, pyrite and calcite. Based on this preliminary work, the North Dakota sample appears to lack both kaolinite and calcite, and the Wyodak sample appears to lack calcite. Subsequent SEM work will attempt to reconfirm

  10. Combustion of coal/water mixtures with thermal preconditioning

    SciTech Connect

    Novack, M.; Roffe, G.; Miller, G.

    1987-01-01

    Thermal preconditioning is a process in which coal/water mixtures are vaporized to produce coal/steam suspensions, and then superheated to allow the coal to devolitalize producing suspensions of char particles in hydrocarbon gases and steam. This final product of the process can be injected without atomization, and burned directly in a gas turbine combustor. This paper reports on the results of an experimental program in which thermally preconditioned coal/water mixture was successfully burned with a stable flame in a gas turbine combustor test rig. Tests were performed at a mixture flowrate of 300 1b/hr and combustor pressure of 8 atmospheres. The coal/water mixture was thermally preconditioned and injected into the combustor over a temperature range from 350/sup 0/F to 600/sup 0/F, and combustion air was supplied at between 600/sup 0/F to 725/sup 0/F. Test durations varied between 10 to 20 minutes. The original mean coal particle size for these tests, prior to preconditioning was 25 microns. Results of additional tests showed that one-third of the sulfur contained in the solids of a coal/water mixture with 3 percent sulfur were evolved in gaseous form (under mild thermolized conditions) mainly as H/sub 2/S with the remainder as light mercaptans.

  11. Grindability and combustion behavior of coal and torrefied biomass blends.

    PubMed

    Gil, M V; García, R; Pevida, C; Rubiera, F

    2015-09-01

    Biomass samples (pine, black poplar and chestnut woodchips) were torrefied to improve their grindability before being combusted in blends with coal. Torrefaction temperatures between 240 and 300 °C and residence times between 11 and 43 min were studied. The grindability of the torrefied biomass, evaluated from the particle size distribution of the ground sample, significantly improved compared to raw biomass. Higher temperatures increased the proportion of smaller-sized particles after grinding. Torrefied chestnut woodchips (280 °C, 22 min) showed the best grinding properties. This sample was blended with coal (5-55 wt.% biomass). The addition of torrefied biomass to coal up to 15 wt.% did not significantly increase the proportion of large-sized particles after grinding. No relevant differences in the burnout value were detected between the coal and coal/torrefied biomass blends due to the high reactivity of the coal. NO and SO2 emissions decreased as the percentage of torrefied biomass in the blend with coal increased. PMID:25997009

  12. Evaluation of catalytic combustion of actual coal-derived gas

    NASA Technical Reports Server (NTRS)

    Blanton, J. C.; Shisler, R. A.

    1982-01-01

    The combustion characteristics of a Pt-Pl catalytic reactor burning coal-derived, low-Btu gas were investigated. A large matrix of test conditions was explored involving variations in fuel/air inlet temperature and velocity, reactor pressure, and combustor exit temperature. Other data recorded included fuel gas composition, reactor temperatures, and exhaust emissions. Operating experience with the reactor was satisfactory. Combustion efficiencies were quite high (over 95 percent) over most of the operating range. Emissions of NOx were quite high (up to 500 ppm V and greater), owing to the high ammonia content of the fuel gas.

  13. Transformations of inorganic coal constituents in combustion systems

    SciTech Connect

    Helble, J.J.; Srinivasachar, S.; Wilemski, G.; Boni, A.A. ); Kang, Shin-Gyoo; Sarofim, A.F.; Graham, K.A.; Beer, J.M. ); Peterson, T.W.; Wendt, J.O.L.; Gallagher, N.B.; Bool, L. ); Huggins, F.E.; Huffman, G.P.; Shah, N.; Shah, A. (Kentucky Univ., Lexingt

    1992-11-01

    Results from an experimental investigation of the mechanisms governing the ash aerosol size segregated composition resulting from the combustion of pulverized coal in a laboratory scale down-flow combustor are described. The results of modeling activities used to interpret the results of the experiments conducted under his subtask are also described in this section. Although results from the entire program are included, Phase II studies which emphasized: (1) alkali behavior, including a study of the interrelationship between potassium vaporization and sodium vaporization; and (2) iron behavior, including an examination of the extent of iron-aluminosilicate interactions, are highlighted. Idealized combustion determination of ash particle formation and surface stickiness are also described.

  14. Balancing act creating the right regulation for coal combustion waste

    SciTech Connect

    Manuel, J.

    2009-11-15

    The December 2008 collapse of a coal ash pond in Tennessee threw safe management of coal combustion waste (CCW) into the spotlight. Millions of tons of CCW are produced in the United States each year, and a large percentage of that is recycled. The US Environmental Protection Agency is pursuing a host of initiatives that could directly or indirectly affect the disposition of CCW. States, too, are taking a look at how they regulate CCW. Among the options is the possibility of regulating CCW under the Resource Conservation and Recovery Act, a move that could have far-reaching implications for both the recycling and the disposal of this waste.

  15. Beneficial use of coal combustion products continues to grow

    SciTech Connect

    MacDonald, M.

    2008-07-01

    In August 2007 the American Coal Ash Association (ACAA) released results of the Coal Combustion Products Production (CCP) and use survey. Production was 124,795,000 tons while beneficial use was 54,203,000 tons, a utilization rate of over 43%, 3% higher than in 2005. The article includes graphs of 40 years of CCP production and use and projected trade of CCP utilization until 2011. It also gives 2006 figures for Production and use of fly ash, bottom ash, boiler slag, FGD gypsum and other FGD products, and FBC ash. 3 refs., 3 figs.

  16. TOXIC SUBSTANCES FROM COAL COMBUSTION-A COMPREHENSIVE ASSESSMENT

    SciTech Connect

    C.L. Senior; F. Huggins; G.P. Huffman; N. Shah; N. Yap; J.O.L. Wendt; W. Seames; M.R. Ames; A.F. Sarofim; S. Swenson; J.S. Lighty; A. Kolker; R. Finkelman; C.A. Palmer; S.J. Mroczkowski; J.J. Helble; R. Mamani-Paco; R. Sterling; G. Dunham; S. Miller

    2001-06-30

    The Clean Air Act Amendments of 1990 identify a number of hazardous air pollutants (HAPs) as candidates for regulation. Should regulations be imposed on HAP emissions from coal-fired power plants, a sound understanding of the fundamental principles controlling the formation and partitioning of toxic species during coal combustion will be needed. With support from the National Energy Technology Laboratory (NETL), the Electric Power Research Institute, and VTT (Finland), Physical Sciences Inc. (PSI) has teamed with researchers from USGS, MIT, the University of Arizona (UA), the University of Kentucky (UK), the University of Connecticut (UC), the University of Utah (UU) and the University of North Dakota Energy and Environmental Research Center (EERC) to develop a broadly applicable emissions model useful to regulators and utility planners. The new Toxics Partitioning Engineering Model (ToPEM) will be applicable to all combustion conditions including new fuels and coal blends, low-NOx combustion systems, and new power generation plants. Development of ToPEM will be based on PSI's existing Engineering Model for Ash Formation (EMAF). The work discussed in this report covers the Phase II program. Five coals were studied (three in Phase I and two new ones in Phase II). In this work UK has used XAFS and Moessbauer spectroscopies to characterize elements in project coals. For coals, the principal use was to supply direct information about certain hazardous and other key elements (iron) to complement the more complete indirect investigation of elemental modes of occurrence being carried out by colleagues at USGS. Iterative selective leaching using ammonium acetate, HCl, HF, and HNO3, used in conjunction with mineral identification/quantification, and microanalysis of individual mineral grains, has allowed USGS to delineate modes of occurrence for 44 elements. The Phase II coals show rank-dependent systematic differences in trace-element modes of occurrence. The work at UU

  17. Analytical and characterization studies of organic and inorganic species in brown coal

    SciTech Connect

    G. Domazetis; M. Raoarun; B.D. James; J. Liesegang; P.; J. Pigram; N. Brack

    2006-08-15

    Detailed studies have been carried out on the distribution of organic functional groups and inorganic species in as-received (ar) and acid-washed (aw) brown coals using elemental analysis, energy dispersive X-ray analysis (SEM-EDX), X-ray photoelectron spectroscopy (XPS), and Time-of-flight-secondary ion mass spectrometry (TOF-SIMS). Surface concentrations of the various carbon groups, organic oxygen, and inorganic hydroxide were obtained using XPS, but oxygen from clay and quartz, if present, interfered with organic oxygen determinations for the coals. A comparison of ar and aw coals using XPS and SEM-EDX is provided in terms of inorganic and organic sulfur groups. Chloride in these coals is present mainly as acid extractable forms, but small amounts of chloride in the organic matrix were indicated by the elemental analysis of ultra low-ash coals. TOF-SIMS fragments from brown coals were indicative of polymers consisting mainly of single aromatic groups linked by hydrocarbons with carboxyl and phenol functional groups. Sulfur fragments were from inorganic sulfur, thiols, organo-sulfates, and S-N-organic species. Numerous fragments containing organically bound chloride were observed. Fragments of the inorganic species Na, Mg, Al, Si, K, Ca, Ti, Cr, Fe, Mn, Ni, Cu, and Ga were also observed. Environmentally undesirable species, particularly from organo-sulfur and organo-chloride groups in brown coal, are likely to emerge from processes that heat coal-water mixture. 54 refs., 3 figs., 10 tabs.

  18. Detection of smoldering combustion of coal with an odor meter

    SciTech Connect

    Edwards, J.C.

    1995-05-01

    A commercially available odor meter was evaluated as a detector of smoldering coal combustion, and compared with incipient carbon monoxide (CO) and hydrogen sulfide (H{sub 2}S) detection and a commercially available ionization-type smoke detector. Ten smoldering coal combustion experiments were conducted. For eight of the experiments, Pittsburgh seam coal with an average particle diameter of approximately 5 cm was heated by embedded electrical strip heaters. For two of the experiments mine size Pittsburgh seam coal was heated. Heating rates of 0.5, 0.8, and 1.1. kw were selected to provide experimental conditions characteristic of very slow and moderately fast heating for coal sample mass between 3 and 10 kg. It was found that the odor meter and smoke detector alarm had a good correlation, with the odor meter alarm occurring prior to the smoke alarm in four of the ten experiments. The odor meter gave an increase in its output signal above ambient equivalent to detecting 1 ppm of H{sub 2}S (ten times the odor threshold of H{sub 2}S) as an alarm value. This observed odor meter response occurred prior to the electrochemical detection of H{sub 2}S for five of the six experiments for which it was evaluated. In all six experiments for which the smoke optical density was evaluated, it was less than 0.023 m{sup -1} prior to the odor meter reaching alarm. In each of the eight experiments with 5 cm diameter coal particles the CO exceeded 5 ppm at odor meter alarm, while for the two experiments with mine size coal the CO was less than 3 ppm at odor meter alarm. The odor meter, as tested, is not a significant improvement over smoke and CO detectors. Because the odor meter responds to a variety of chemical compounds, with suitable modification and increased sensitivity it may be useful for detection of mine fires and thereby enhance mine safety.

  19. HIGH PRESSURE COAL COMBUSTION KINETICS PROJECT

    SciTech Connect

    Chris Guenther, Ph.D.

    2003-01-28

    SRI has completed the NBFZ test program, made modification to the experimental furnace for the HPBO test. The NBFZ datasets provide the information NEA needs to simulate the combustion and fuel-N conversion with detailed chemical reaction mechanisms. BU has determined a linear swell of 1.55 corresponding to a volumetric increase of a factor of 3.7 and a decrease in char density by the same factor. These results are highly significant, and indicate significantly faster burnout at elevated pressure due to the low char density and large diameter.

  20. Development of coal combustion sensitivity test for smoke detectors

    SciTech Connect

    Edwards, J.C.; Morrow, G.S.

    1995-09-01

    Standard smoldering and flaming combustion tests using small coal samples have been developed by the US Bureau of Mines as a method to evaluate the response of a smoke detector. The tests are conducted using a standard smoke box designed and constructed according to Underwriters Laboratories. The tests provide a standard, easily reproducible smoke characteristic for smoldering and flaming coal combustion, based upon a comparison of the smoke optical density and the response of a standard ionization chamber to the smoke. With these standard tests, the range of threshold limits for the response of a smoke detector and the detector`s reliability can be evaluated for nearly identical smoke visibility and smoke physical characteristics. The detector`s threshold response limits and reliability need to be well defined prior to the instrument`s use as part of a mine fire warning system for improved mine safety.

  1. EFFECTS OF IRON CONTENT IN COAL COMBUSTION FLY ASHES ON SPECIATION OF MERCURY

    EPA Science Inventory

    The paper discusses the effects of iron content in coal combustion fly ashes on speciation of mercury. (NOTE: The chemical form of mercury species in combustion flue gases is an important influence on the control of mercury emissions from coal combustion). The study focused on th...

  2. Near-extinction and final burnout in coal combustion

    SciTech Connect

    Hurt, R.H.; Davis, K.A.

    1994-02-01

    The late stages of char combustion have a special technological significance, as carbon conversions of 99% or greater are typically required for the economic operation of pulverized coal fired boilers. In the present article, two independent optical techniques are used to investigate near-extinction and final burnout phenomenas. Captive particle image sequences, combined with in situ optical measurements on entrained particles, provide dramatic illustration of the asymptotic nature of the char burnout process. Single particle combustion to complete burnout is seen to comprise two distinct stages: (1) a rapid high-temperature combustion stage, consuming about 70% of the char carbon and ending with near-extinction of the heterogeneous reactions due to a loss of global particle reactivity, and (2) a final burnout stage occurring slowly at lower temperatures. For particles containing mineral matter, the second stage can be further subdivided into: (2a) late char combustion, which begins after the near-extinction event, and converts carbon-rich particles to mixed particle types at a lower temperature and a slower rate; and (2b) decarburization of ash -- the removal of residual carbon inclusions from inorganic (ash) frameworks in the very late stages of combustion. This latter process can be extremely slow, requiring over an order of magnitude more time than the primary rapid combustion stage. For particles with very little ash, the loss of global reactivity leading to early near-extinction is clearly related to changes in the carbonaceous char matrix, which evolves over the course of combustion. Current global kinetic models used for the prediction of char combustion rates and carbon burnout in boilers do not predict the asymptotic nature of char combustion. More realistic models accounting for the evolution of char structure are needed to make accurate predictions in the range of industrial interest.

  3. HIGH PRESSURE COAL COMBUSTION KINETICS PROJECT

    SciTech Connect

    Chris Guenther

    2002-10-28

    The modifications to the SRT-RCFR facility described in the June report were completed. As a result of these changes, the furnace hot zone was increased in length from 7 cm to 15.5 cm. The injector region of the furnace, providing entrainment and sheath flows, was unchanged, while the flow path from the exit of the furnace to the sample collection section was shortened by approximately 10 cm. The modified facility was used to resume testing of Pittsburgh No. 8 coal at 10 atm. The first goal was to confirm that the facility now provides true secondary pyrolysis test conditions. That is, the tar product should be completely converted to soot even in the absence of oxygen in the gas stream. We have now performed four tests with pure argon carrier gas, and have consistently observed voluminous soot product with little or no evidence of tar. Thus, this objective was met. The clogging problems for Pittsburgh No. 8 coal under secondary pyrolysis test conditions may preclude achieving this data point. In that case, we will make measurements under oxidizing conditions, which are expected to eliminate the clogging, and to gradually reduce the oxygen content to the point where product yields can reliably be extrapolated to the zero oxygen case.

  4. Combustion and fuel characterization of coal-water fuels

    SciTech Connect

    Lachowicz, Y.V.; LaFlesh, R.C.

    1987-07-01

    This five-year research project was established to provide sufficient data on coal-water fuel (CWF) chemical, physical, and combustion properties to assess the potential for commercial firing in furnaces designed for gas or oil firing. Extensive laboratory testing was performed at bench-scale, pilot-scale (4 {times} 10{sup 6}Btu/hr) and commercial-scale (25 {times} 10{sup 6} to 50 {times} 10{sup 6}Btu/hr) on a cross-section of CWFs. Fuel performance characteristics were assessed with respect to coal properties, level of coal beneficiation, and slurry formulation. The performance of four generic burner designs was also assessed. Boiler performance design models were applied to analyze the impacts associated with conversion of seven different generic unit designs to CWF firing. Equipment modifications, operating limitations, and retrofit costs were determined for each design when utilizing several CWFs. This report summarizes studies conducted under Task 4. The objective was to quantify CWF atomization and combustion properties utilizing industrial/utility scale equipment. Burners were evaluated and combustion performance differences identified for various CWF formulations. 12 refs., 23 figs., 6 tabs.

  5. [Development of mercury emission inventory from coal combustion in China].

    PubMed

    Jiang, Jing-kun; Hao, Ji-ming; Wu, Ye; Streets, David G; Duan, Lei; Tian, He-zhong

    2005-03-01

    Mercury emission inventory by province from coal combustion in China was developed by combining fuel consumption, mercury content in fuel and emission factors after combustion in this study. The study is intended to provide an understanding of mercury transformation, transportation and deposition in atmosphere, as well as propose measures to control mercury pollution in China. Mercury emission sources were classified into 65 categories by economic sectors, fuel types, boiler types and pollution control technologies. For two different data sets of mercury content in coal the total amounts of mercury released into atmosphere in 2000 in China were estimated at about 161.6 tons and 219.5 tons, respectively. The biggest three source sectors were industry, power plants, and residential use, contributing 46%, 35% and 14% of total mercury emissions, respectively. The shares of elemental mercury (Hg0), oxidized mercury (Hg2+ ) and particulate mercury (Hgp) were 16% , 61% and 23% , respectively. The spatial distribution of mercury emissions from coal combustion in China is not uniform. Henan, Shanxi, Hebei, Liaoning and Jiangsu contributed large amounts of mercury emissions, exceeding 10t x a(- 1). PMID:16004296

  6. Combustion studies of coal derived solid fuels by thermogravimetric analysis. III. Correlation between burnout temperature and carbon combustion efficiency

    USGS Publications Warehouse

    Rostam-Abadi, M.; DeBarr, J.A.; Chen, W.T.

    1990-01-01

    Burning profiles of 35-53 ??m size fractions of an Illinois coal and three partially devolatilized coals prepared from the original coal were obtained using a thermogravimetric analyzer. The burning profile burnout temperatures were higher for lower volatile fuels and correlated well with carbon combustion efficiencies of the fuels when burned in a laboratory-scale laminar flow reactor. Fuels with higher burnout temperatures had lower carbon combustion efficiencies under various time-temperature conditions in the laboratory-scale reactor. ?? 1990.

  7. Product composition of the dynamic conversion of brown coal in supercritical water

    SciTech Connect

    O.N. Fedyaeva; A.A. Vostrikov; D.Y. Dubov; S.A. Psarov; M.Y. Sokol

    2007-12-15

    The product composition of the dynamic conversion of brown coal, which was continuously supplied as a water-coal slurry to a flow reactor at 30 MPa, was studied. The temperature of water and coal particles was increased from room temperature to 400{sup o}C (top part of the reactor). The conversion of the organic matter of coal was about 48%, and the products collected at the reactor outlet consisted of solid tar components, substances dissolved and emulsified in water, and volatile substances, whose major constituent was CO{sub 2}. The composition of solid tar components and oils was determined.

  8. Combustion and fuel characterization of coal-water fuels

    SciTech Connect

    Not Available

    1989-07-01

    Pittsburgh Energy Technology Center (PETC) of the Department of Energy initiated a comprehensive effort in 1982 to develop the necessary performance and cost data and to assess the commercial viability of coal water fuels (CWFs) as applied to representative utility and industrial units. The effort comprised six tasks beginning with coal resource evaluation and culminating in the assessment of the technical and economic consequences of switching representative commercial units from oil to state-of-the-art CWF firing. Extensive bench, pilot and commercial-scale tests were performed to develop necessary CWF combustion and fireside performance data for the subsequent boiler performance analyses and retrofit cost estimates. This report (Volume 2) provides a review of the fuel selection and procurement activities. Included is a discussion on coal washability, transport of the slurry, and characterization. 20 figs., 26 tabs.

  9. Catalytic effects of minerals on NOx emission from coal combustion

    SciTech Connect

    Yao, M.Y.; Che, D.F.

    2007-07-01

    The catalytic effects of inherent mineral matters on NOx emissions from coal combustion have been investigated by a thermo-gravimetric analyzer (TGA) equipped with a gas analyzer. The effect of demineralization and the individual effect of Na, K, Ca, Mg, and Fe on the formation of NOx are studied as well as the combined catalytic effects of Ca + Na and Ca + Ti. Demineralization causes more Fuel-N to retain in the char, and reduction of NOx mostly. But the mechanistic effect on NOx formation varies from coal to coal. Ca and Mg promote NOx emission. Na, K, Fe suppress NOx formation to different extents. The effect of transition element Fe is the most obvious. The combination of Ca + Na and Ca + Ti can realize the simultaneous control of sulfur dioxide and nitrogen oxides emissions.

  10. Field studies of the leachability of aged brown coal ash.

    PubMed

    Mudd, G M; Kodikara, J

    2000-09-15

    The environmental management of ash produced from the brown coal power stations of the Latrobe Valley region of Australia has been studied. Current practice consists of slurrying fly and bottom ash, a short distance to an ash disposal pond. However, storage facilities are approaching capacity and alternative ash management strategies are required in the near future. Initially, the ash produced within the power stations is known to possess a large soluble mass, which can leach rapidly to generate a saline leachate with minor trace metal content. After slurrying and deposition within the ash pond, it has been demonstrated that the soluble mass is significantly lower and the ash can be considered as aged or "leached" ash - a more benign waste that meets the criteria for fill material. In order to assess the long-term behaviour of the leached ash and its suitability for co-disposal in engineered sites within overburden dumps, two field cells were constructed and monitored over a period of 1 year. Each cell was 5 x 5 m in area, 3-m deep and HDPE lined with a coarse drainage layer and leachate collection pipe. The first cell only collected natural rainfall and was known as the Dry Cell. The second cell had an external tank of 5000 l installed (200-mm rainfall equivalent) and water was spray-irrigated regularly to simulate higher rainfall and accelerate the leaching process. The cumulative inflow and outflow for each cell has been calculated using a linear relationship and the leachate quality was monitored over time. The results demonstrate that the ash behaves as an unsaturated porous material, with the effect of evaporation through the profile being dominant and controlling the production of leachate. The leachate quality was initially moderately saline in both cells, with the concentration dropping by nearly 95% in the Wet Cell by the end of the field study. The leachate chemistry has been analysed using the PHREEQC geochemical model. The log activity plots of various

  11. Influence of carbon structure and mineral association of coals on their combustion characteristics for pulverized coal injection (PCI) application

    SciTech Connect

    Gupta, S.; Al-Omari, Y.; Sahajwalla, V.; French, D.

    2006-06-15

    The influence of carbon structure and mineral matter of three pulverized coals on their char characteristics including reactivity was studied under a range of combustion conditions in a drop tube furnace (DTF) and thermogravimetric (TGA) furnace for PCI application. Physical and chemical properties of coals and their combustion derivatives were characterized by automated reflectogram. X-ray diffraction, scanning electron microscope, and BET N{sub 2} adsorption. The QEMSCAN{asterisk} technique was used to characterize the heterogeneous nature of minerals of discrete coal particles. The TGA char reactivity was related to the proportion of coal particles displaying strong association of calcium/sulfur phases with carbon matrix to highlight the catalytic influence of minerals on char reactivity at low temperatures. The study suggested that during DTF combustion tests at 1200{sup o}C, char reaction rates might have been catalyzed by coal minerals, particularly due to illite and its association with carbon. Under the same combustion conditions, most of the coal minerals did not transform significantly to slag phases. Coal burnout was found to improve significantly in a combustion temperature range of 1200 to 1500{sup o}C. The improvement of coal burnout with temperature appeared to be influenced by coal properties, particularly as a function of the chemical nature of minerals, as well as the degree of associations with other minerals. The study implies that coals with similar mineral compositions might not necessarily reflect similar combustion behavior due to the differences in their associations with other phases.

  12. Toxic Substances from Coal Combustion - Forms of Occurrence Analyses

    SciTech Connect

    Allan Kolker; Curtis A. Palmer; Harvey E. Belkin; Jason Willet; Kathleen C. Kolb; Robert B. Finkelman; Sharon S. Crowley; Stanley J. Mroczkowski

    1998-12-14

    In a cooperative agreement with DOE (Contract No. DE- AC22- 95101), the USGS has participated with Physical Sciences, Inc. (PSI) in a project entitled "Toxic Substances From Coal Combustion -A Comprehensive Assessment". Samples from the Pittsburgh, Elkhorn/ Hazard, Illinois No. 6, and Wyodak program coals were examined to determine the mode of occurrence of selected trace elements (As, Se, Cr, Hg, and Ni) using selective leaching, scanning electron microscopy, electron microprobe analysis, and X- ray diffraction techniques. Among other findings, our results indicate that the bulk of the arsenic in the Pittsburgh and Illinois No. 6 coals is in pyrite. High percentages (60- 80%) of arsenic were leached by nitric acid, and microprobe data confirm the presence of arsenic in pyrite in each of these coals (concentrations ranging from <0.01 to 0.09 wt.% of the pyrite grains). In the Elkhorn/ Hazard coal, arsenic may have several modes of occurrences. About 30 percent of the arsenic in the Elkhorn/ Hazard coal was leached by hydrochloric acid, possibly indicating the presence of arsenates that were formed by the oxidation of pyrite. About 25 percent of the arsenic in the Elkhorn/ Hazard coal was leached by nitric acid, suggesting an association with pyrite. Only sixty percent of the total arsenic in the Elkhorn/ Hazard coal was leached. The low percentage of leachable arsenic may be accounted for by unleached pyrite grains, which were detected in solid residues from the nitric acid leach. In the Wyodak coal, arsenic probably occurs in iron oxides or carbonates (35 % arsenic leached by HCl) and clays (15% arsenic leached by HF). Arsenic in the Wyodak coal may also have an organic association, as indicated by low totals for leaching (50% unleached arsenic). In the four program coals 20 to 45 percent of the chromium was leached by hydrofluoric acid, suggesting an association with silicates (probably illite). Microprobe analysis of the Pittsburgh, Elkhorn/ Hazard, and Illinois

  13. Evaluation of engineering properties for the use of leached brown coal ash in soil covers.

    PubMed

    Mudd, Gavin M; Chakrabarti, Srijib; Kodikara, Jayantha

    2007-01-31

    The need to engineer cover systems for the successful rehabilitation or remediation of a wide variety of solid wastes is increasing. Some common applications include landfills, hazardous waste repositories, or mine tailings dams and waste rock/overburden dumps. The brown coal industry of the Latrobe Valley region of Victoria, Australia, produces significant quantities of coal ash and overburden annually. There are some site-specific acid mine drainage (AMD) issues associated with overburden material. This needs to be addressed both during the operational phase of a project and during rehabilitation. An innovative approach was taken to investigate the potential to use leached brown coal ash in engineered soil covers on this overburden dump. The basis for this is two-fold: first, the ash has favourable physical characteristics for use in cover systems (such as high storage capacity/porosity, moderately low permeability, and an ability to act as a capillary break layer generating minimal leachate or seepage); and second, the leachate from the ash is mildly alkaline (which can help to mitigate and reduce the risk of AMD). This paper will review the engineering issues involved in using leached brown coal ash in designing soil covers for potentially acid-forming overburden dumps. It presents the results of laboratory work investigating the technical feasibility of using leached brown coal ash in engineered solid waste cover systems. PMID:16621267

  14. ON TRIMODAL PARTICLE SIZE DISTRIBUTIONS IN FLY ASH FROM PULVERIZED COAL COMBUSTION

    EPA Science Inventory

    Combustion generated fine particles, defined as those with aerodynamic diameters less than 2.5 micrometers, have come under increased regulatory scrutiny because of suspected links to adverse human health effects. Whereas classical theories regarding coal combustion suggest that ...

  15. LES Modeling of Oxy-combustion of Pulverized Coal: Preliminary Study

    NASA Astrophysics Data System (ADS)

    Warzecha, Piotr; Boguslawski, Andrzej

    2009-12-01

    The paper presents preliminary results of pulverized coal combustion process modeling using Large Eddy Simulation. First the methodology for the testing of mesh resolution is presented. The combustion process was carried out using equilibrium model with single mixture fraction approach.

  16. Coal slurry combustion optimization on single cylinder engine

    SciTech Connect

    Not Available

    1992-09-01

    Under the sponsorship of the US Department of Energy, Morgantown Energy Technology Center, GE Transportation System has been conducting a proof of concept program to use coal water slurry (CWS) fuel to power a diesel engine locomotive since 1988. As reported earlier [1], a high pressure electronically controlled accumulator injector using a diamond compact insert nozzle was developed for this project. The improved reliability and durability of this new FIE allowed for an improved and more thorough study of combustion of CWS fuel in a diesel engine. It was decided to include a diesel pilot fuel injector in the combustion system mainly due to engine start and low load operation needs. BKM, Inc. of San Diego, CA was contracted to develop the electronic diesel fuel pilot/starting FIE for the research engine. As a result, the experimental combustion study was very much facilitated due to the ability of changing pilot/CWS injection timings and quantities without having to stop the engine. Other parameters studied included combustion chamber configuration (by changing CWS fuel injector nozzle hole number/shape/angle), as well as injection pressure. The initial phase of this combustion study is now complete. The results have been adopted into the design of a 12 cylinder engine FIE, to be tested in 1992. This paper summarizes the main findings of this study.

  17. Preparation and combustion of high ash coal tailing slurry

    SciTech Connect

    Zhang Ziping; Zhang Wenfu; Fu Xiaoheng; Wang Zuna; Li Hui

    1998-12-31

    Flotation tailings from a coal preparation plant are known for their high ash, low heating value, high moisture content even after thickening and filtration, and difficult handability. However, they can be easily converted into a slurry fuel for boilers. Two flotation tailings, containing ash of 31.89% and 41.87% respectively, have been converted into slurry fuel with the following properties: solid content being 70.4% and 74.4% respectively; low heating value, 13,694kj/kg and 10,970kj/kg; and viscosity, 379 mPa.s and 180 mPa.s at a shear rate of 100s{sup {minus}1}. An eccentric slant jet coal slurry burner was installed at the boiler. Slurry atomizing nozzle operated at low pressure. Both slurries gave stable combustion without supporting fuel under the condition of cool air supply. A new way of flotation tailing utilization was demonstrated. China has more than 200 coal preparation plants washing more than 300 million tons of coal annually. These preparation plants generate more than 10 million tons of tailing annually, most of which is not currently being used, causing great environmental pollution and waste management difficulties for the enterprises. Comprehensive utilization of coal washer tailings is one of the key issues of environmental protection and energy saving in China.

  18. Toxic substances from coal combustion--forms of occurrence analyses

    SciTech Connect

    Crowley, S.S.; Palmer, C.A.; Kolker, A.; Finkelman, R.B.; Kolb, K.C.; Belkin, H.E.; Willet, J.C.

    1997-04-01

    The objective of this project was to provide analytical support for the Physical Sciences, Inc. (PSI) projects being performed under DOE Contract No. DE-AC22-95101 entitled `Toxic Substances from Coal Combustion - A Comprehensive Assessment`. The Pittsburgh, Elkhorn/Hazard, and Illinois No. 6 program coals were examined to determine the mode of occurrence of selected trace elements (As, Se, Cr, Hg, and Ni) using selective leaching, scanning electron microscopy, electron microprobe analysis, and X-ray diffraction techniques. Preliminary work was also completed for the Wyodak coal. Among other findings, our results indicate that the bulk of the arsenic in the Pittsburgh and Illinois No. 6 coals is in pyrite. High percentages (60-80%) of arsenic were leached by nitric acid, and microprobe data confirm the presence of arsenic in pyrite in each of these coals (concentrations ranging from <0.01 to 0.09 wt.% of the pyrite grains). In the Elkhorn/Hazard coal, arsenic may have several modes of occurrences. About 30 percent of the arsenic in the Elkhorn/Hazard coal was leached by hydrochloric acid, possibly indicating the presence of arsenates that were formed by the oxidation of pyrite. About 25 percent of the arsenic in the Elkhorn/Hazard coal was leached by nitric acid, suggesting an association with pyrite. Only sixty percent of the total arsenic in the Elkhorn/Hazard coal was leached. The low percentage of leachable arsenic may be accounted for by unleached pyrite grains, which were detected in solid residues from the nitric acid leach. In the Pittsburgh, Elkhorn/Hazard, and Illinois No. 6 coals, 20 to 25 percent of the chromium was leached by hydrofluoric acid, indicating some association with silicates (possibly illite). Microprobe analysis of these coals confirmed the presence of chromium in illite and possibly in other clays, at concentrations that were near the detection limits. Results related to the forms of occurrences of the other trace elements (Se, Hg, and Ni

  19. Correlations between petrographical properties, chemical structure and technological behaviour of Rhenish brown coal

    SciTech Connect

    Wolfrum, E.A.

    1983-08-01

    For the purpose of an assessment with a view to refining, the petrographical, chemical and physical properties of lithotypes of Rhenish brown coal were established and compared with one another. The investigated coal types cover more than 90% of the coal types proved in the Rhenish deposit. A correlation of the results shows a describable, sometimes multidimensional dependency. A comparison of raw material properties and the results of the technical experiments quickly reveals the limits set to such an approach. Out of all the refining processes subjected to investigation briquetting places the highest requirements on the raw material properties. The major part of the established parameters leads only to qualitative indications of the briquetting properties of the coals. Parameters of greater significance can hardly be utilized in practice. What remains in the experience gained by coal technologists, is the determination of the classical coal properties and indications from laboratory briquetting.

  20. Obtaining of gas, liquid, and upgraded solid fuel from brown coals in supercritical water

    NASA Astrophysics Data System (ADS)

    Vostrikov, A. A.; Fedyaeva, O. N.; Dubov, D. Yu.; Shishkin, A. V.; Sokol, M. Ya.

    2013-12-01

    Two new conversion methods of brown coals in water steam and supercritical water (SCW) are proposed and investigated. In the first method, water steam or SCW is supplied periodically into the array of coal particles and then is ejected from the reactor along with dissolved conversion products. The second method includes the continuous supply of water-coal suspension (WCS) into the vertically arranged reactor from above. When using the proposed methods, agglomeration of coal particles is excluded and a high degree of conversion of coal into liquid and gaseous products is provided. Due to the removal of the main mass of oxygen during conversion in the composition of CO2, the high heating value of fuels obtained from liquid substantially exceeds this characteristic of starting coal. More than half of the sulfur atoms transfer into H2S during the SCW conversion already at a temperature lower than 450°C.

  1. Temporal measurements and kinetics of selenium release during coal combustion and gasification in a fluidized bed.

    PubMed

    Shen, Fenghua; Liu, Jing; Zhang, Zhen; Yang, Yingju

    2016-06-01

    The temporal release of selenium from coal during combustion and gasification in a fluidized bed was measured in situ by an on-line analysis system of trace elements in flue gas. The on-line analysis system is based on an inductively coupled plasma optical emission spectroscopy (ICP-OES), and can measure concentrations of trace elements in flue gas quantitatively and continuously. The results of on-line analysis suggest that the concentration of selenium in flue gas during coal gasification is higher than that during coal combustion. Based on the results of on-line analysis, a second-order kinetic law r(x)=0.94e(-26.58/RT)(-0.56 x(2) -0.51 x+1.05) was determined for selenium release during coal combustion, and r(x)=11.96e(-45.03/RT)(-0.53 x(2) -0.56 x+1.09) for selenium release during coal gasification. These two kinetic laws can predict respectively the temporal release of selenium during coal combustion and gasification with an acceptable accuracy. Thermodynamic calculations were conducted to predict selenium species during coal combustion and gasification. The speciation of selenium in flue gas during coal combustion differs from that during coal gasification, indicating that selenium volatilization is different. The gaseous selenium species can react with CaO during coal combustion, but it is not likely to interact with mineral during coal gasification. PMID:26897573

  2. CONTROL OF TRACE METAL EMISSIONS DURING COAL COMBUSTION

    SciTech Connect

    THOMAS C. HO

    1998-02-18

    Emissions of toxic trace metals in the form of metal fumes or submicron particulates from a coal-fired combustion source have received greater environmental and regulatory concern over the past years. Current practice of controlling these emissions is to collect them at the cold-end of the process by air-pollution control devices (APCDs) such as electrostatic precipitators and baghouses. However, trace metal fumes may not always be effectively collected by these devices because the formed fumes are extremely small. The proposed research is to explore the opportunities for improved control of toxic trace metal emissions, alternatively, at the hot-end of the coal combustion process, i.e., in the combustion chamber. The technology proposed is to prevent the metal fumes from forming during the process, which would effectively eliminate the metal emission problems. Specifically, the technology is to employ suitable sorbents to (1) reduce the amount of metal volatilization during combustion and (2) capture volatilized metal vapors. The objectives of the project are to demonstrate the technology and to characterize the metal capture process during coal combustion in a fluidized bed combustor. This final technical report details the work performed, the conclusions obtained, and the accomplishments achieved over the project performance period from July 1, 1994 through December 31, 1997. Specifically, this report consists of the following five chapters: Chapter 1. Executive Summary; Chapter 2. Metal Capture by Various Sorbents; Chapter 3. Simultaneous Metal and Sulfur Capture; Chapter 4. Sorption and Desorption of Mercury on Sorbents; and Chapter 5. Project Conclusions. In summary, the metals involved in the project were arsenic, cadmium, chromium, lead, mercury and selenium and the sorbents tested included bauxite, zeolite and calcined limestone. The three sorbents have been found to have various degree of metal capture capability on arsenic, cadmium, chromium and lead

  3. Method for reducing NOx during combustion of coal in a burner

    DOEpatents

    Zhou, Bing; Parasher, Sukesh; Hare, Jeffrey J.; Harding, N. Stanley; Black, Stephanie E.; Johnson, Kenneth R.

    2008-04-15

    An organically complexed nanocatalyst composition is applied to or mixed with coal prior to or upon introducing the coal into a coal burner in order to catalyze the removal of coal nitrogen from the coal and its conversion into nitrogen gas prior to combustion of the coal. This process leads to reduced NOx production during coal combustion. The nanocatalyst compositions include a nanoparticle catalyst that is made using a dispersing agent that can bond with the catalyst atoms. The dispersing agent forms stable, dispersed, nano-sized catalyst particles. The catalyst composition can be formed as a stable suspension to facilitate storage, transportation and application of the catalyst nanoparticles to a coal material. The catalyst composition can be applied before or after pulverizing the coal material or it may be injected directly into the coal burner together with pulverized coal.

  4. Combustion of volatile matter during the initial stages of coal combustion

    SciTech Connect

    Marlow, D.; Niksa, S.; Kruger, C.H.

    1990-08-01

    Both the secondary pyrolysis and combustion of the volatiles from a bituminous coal will be studied. Devolatilization and secondary pyrolysis experiments will be conducted in a novel flow reactor in which secondary pyrolysis of the volatiles occurs after devolatilization is complete. This allows unambiguous measurements of the yields from both processes. Measurements will be made for reactor temperatures from 1500 to 1700 K, and a nominal residence time of 200 msec. These conditions are typical of coal combustion. Yields of tar, soot, H{sub 2}, CO, CH{sub 4}, and C{sub 2} and C{sub 3} hydrocarbons will be determined as a function of reactor temperature. The yields will be reported as a function of the temperature of the reactor. The instrumentation for temperature measurements will be developed during future studies. Combustion studies will be conducted in a constant volume bomb, which will be designed and constructed for this study. Tar and soot will be removed before introducing the volatiles to the bomb, so that only the combustion of the light gas volatiles will be considered. The burning velocities of light gas volatiles will be determined both as functions of mixture stoichiometry and the temperature at which the volatiles are pyrolysed. 90 refs., 70 figs., 13 tabs.

  5. Modeling of pulverized coal combustion in cement rotary kiln

    SciTech Connect

    Shijie Wang; Jidong Lu; Weijie Li; Jie Li; Zhijuan Hu

    2006-12-15

    In this paper, based on analysis of the chemical and physical processes of clinker formation, a heat flux function was introduced to take account of the thermal effect of clinker formation. Combining the models of gas-solid flow, heat and mass transfer, and pulverized coal combustion, a set of mathematical models for a full-scale cement rotary kiln were established. In terms of commercial CFD code (FLUENT), the distributions of gas velocity, gas temperature, and gas components in a cement rotary kiln were obtained by numerical simulation of a 3000 t/d rotary kiln with a four-channel burner. The predicted results indicated that the improved model accounts for the thermal enthalpy of the clinker formation process and can give more insight (such as fluid flow, temperature, etc,) from within the cement rotary kiln, which is a benefit to better understanding of combustion behavior and an improvement of burner and rotary kiln technology. 25 refs., 12 figs., 5 tabs.

  6. On-Line Analysis and Kinetic Behavior of Arsenic Release during Coal Combustion and Pyrolysis.

    PubMed

    Shen, Fenghua; Liu, Jing; Zhang, Zhen; Dai, Jinxin

    2015-11-17

    The kinetic behavior of arsenic (As) release during coal combustion and pyrolysis in a fluidized bed was investigated by applying an on-line analysis system of trace elements in flue gas. This system, based on inductively coupled plasma optical emission spectroscopy (ICP-OES), was developed to measure trace elements concentrations in flue gas quantitatively and continuously. Obvious variations of arsenic concentration in flue gas were observed during coal combustion and pyrolysis, indicating strong influences of atmosphere and temperature on arsenic release behavior. Kinetic laws governing the arsenic release during coal combustion and pyrolysis were determined based on the results of instantaneous arsenic concentration in flue gas. A second-order kinetic law was determined for arsenic release during coal combustion, and the arsenic release during coal pyrolysis followed a fourth-order kinetic law. The results showed that the arsenic release rate during coal pyrolysis was faster than that during coal combustion. Thermodynamic calculations were carried out to identify the forms of arsenic in vapor and solid phases during coal combustion and pyrolysis, respectively. Ca3(AsO4)2 and Ca(AsO2)2 are the possible species resulting from As-Ca interaction during coal combustion. Ca(AsO2)2 is the most probable species during coal pyrolysis. PMID:26488499

  7. Metallic species derived from fluidized bed coal combustion. [59 references

    SciTech Connect

    Natusch, D.F.S.; Taylor, D.R.

    1980-01-01

    Samples of fly ash generated by the combustion of Montana Rosebud coal in an experimental 18 inch fluidized bed combustor were collected. The use of a heated cascade impactor permitted collection of size fractionated material that avoided condensation of volatile gases on the particles. Elemental concentration trends were determined as a function of size and temperature and the results compared to published reports for conventional power plants. The behavior of trace metals appears to be substantially different in the two systems due to lower operating temperatures and the addition of limestone to the fluidized bed. Corrosion of the impactor plates was observed at the highest temperature and lowest limestone feed rate sampled during the study. Data from the elemental concentration and leaching studies suggest that corrosion is most likely due to reactions involving sodium sulfate. However, it is concluded that corrosion is less of a potential problem in fluidized-bed systems than in conventional coal-fired systems.

  8. Release of mercury vapor from coal combustion ash.

    PubMed

    Heebink, Loreal V; Hassett, David J

    2002-08-01

    The long-term stability of Hg in coal combustion by-products (CCBs) was evaluated at ambient and near-ambient temperatures. Six CCB samples with atypically high levels of total Hg were selected for study assuming a greater potential for release of measurable amounts of Hg vapor. The samples selected included two fly ash samples from U.S. eastern bituminous coal, two fly ash samples from South African low-rank coal, one fly ash from Powder River Basin (PRB) subbituminous coal blended with petroleum coke, and one PRB subbituminous coal fly ash incorporated with flue gas desulfurization material. Air scrubbed of Hg was passed through compacted 100-g aliquots of each sample at 1 mL/min and vented to a gold-coated quartz trap to collect released Hg vapor. The samples were maintained at ambient and near-ambient (37 degrees C) temperatures. All samples released low-picogram levels of Hg after 90 days. No pattern was evident to link the total Hg content to the rate of release of Hg vapor. An average of 0.030 pg Hg/g CCB/day was released from the samples, which equates to 2.2 x 10(-8) lb Hg/ton CCB/year. If this were applied to a coal-fired power plant production of 200,000 tons of fly ash per year, there would be a maximum potential release of 0.0044 lb, or 2.00 g, of Hg per year. Experiments are continuing to determine long-term vapor release of Hg from CCBs. All samples have been set up in duplicate at ambient temperature with an improved apparatus to reevaluate results reported in this article. PMID:12184691

  9. Economic realities of coal combustion by-product utilization

    SciTech Connect

    Colmar, J.A.

    1997-09-01

    The purpose of this paper is to highlight the economic issues associated with coal combustion by-product (CCB) utilization and to discuss both technical and cost considerations of commercialization. Handling, processing, and distribution aspects as well as geographic location and competing materials will affect utilization. Several case studies including fly ash in rick, FGD gypsum vs. mined gypsum, and bottom ash vs. lightweight aggregate are presented detailing these issues. Understanding these factors will provide insight to evaluating barriers for CCB utilization which is the first step toward high volume CCB utilization.

  10. Transformations of inorganic coal constituents in combustion systems

    SciTech Connect

    Helble, J.J.; Srinivasachar, S.; Wilemski, G.; Boni, A.A. ); Kang, Shim-Gyoo; Sarofim, A.F.; Graham, K.A.; Beer, J.M. ); Peterson, T.W.; Wendt, O.L.; Gallagher, N.B.; Bool, L. ); Huggins, F.E.; Huffman, G.P.; Shah, N.; Shah, A. (Kentucky Univ., Lexington

    1992-11-01

    This report contains the computer codes developed for the coal combustion project. In Subsection B.1 the FORTRAN code developed for the percolative fragmentation model (or the discrete model, since a char is expressed as a collection of discrete elements in a discrete space) is presented. In Subsection B.2 the code for the continuum model (thus named because mineral inclusions are distributed in a continuum space) is presented. A stereological model code developed to obtain the pore size distribution from a two-dimensional data is presented in Subsection B.3.

  11. CaO interaction in the staged combustion of coal

    SciTech Connect

    Levy, A.; Merryman, E.L.; Rising, B.W.

    1983-12-19

    The LIMB (limestone injection multi-stage burner) process offers special potential for reducing NO/sub x/ and SO/sub x/ by at least 50 percent in coal combustion. This is to be accomplished by adding limestone with fuel and/or air in a low NO/sub x/ burner. This program has been directed to defining the chemistry and kinetics necessary to optimize sulfur capture in LIMB combustion. More specifically, this program has attempted to clarify the role of calcium sulfide in LIMB chemistry. When limestone is added in a staged burner, there is a strong possibility that under certain circumstances CaS is produced in the reducing (fuel-rich) zone of the burner. Since CaS is more stable than CaSO/sub 4/, this affords the opportunity to (1) operate the burner at a higher temperature, 2200 to 2500 F, (2) pass the CaS rapidly through the high temperature zone (before dissociation), and (3) complete the combustion in a lean (air-rich) region where the sulfur is finally retained in CaSO/sub 4/. For these reasons this program has concentrated on the high temperature chemistry and kinetics of CaS. To achieve the program objective, the program was divided into three tasks. These involved (1) a study of CaS formation, (2) a brief examination of CaS oxidation, and (3) a laboratory examination of the combustion of coal in the presence of CaO under first stage, fuel-rich conditions. In the most general sense, the study has shown that the formation of CaS in the reducing zones of the burner may be restricted by competing kinetics and thermodynamics. The addition of lime in LIMB will require special care to optimize the ability to capture sulfur. 36 references, 44 figures, 10 tables.

  12. Combustion and fuel characterization of coal-water fuels

    SciTech Connect

    Chow, O.K.; Gralton, G.W.; Lachowicz, Y.V.; Laflesh, R.C.; Levasseur, A.A.; Liljedahl, G.N.

    1989-02-01

    This five-year research project was established to provide sufficient data on coal-water fuel (CWF) chemical, physical, and combustion properties to assess the potential for commercial firing in furnaces designed for gas or oil firing. Extensive laboratory testing was performed at bench-scale, pilot-scale (4 {times} 10{sup 6}Btu/hr) and commercial-scale (25 {times} 10{sup 6} to 50 {times} 10{sup 6}Btu/hr) on a cross-section of CWFs. Fuel performance characteristics were assessed with respect to coal properties, level of coal beneficiation, and slurry formulation. The performance of four generic burner designs was also assessed. Boiler performance design models were applied to analyze the impacts associated with conversion of seven different generic unit designs to CWF firing. Equipment modifications, operating limitations, and retrofit costs were determined for each design when utilizing several CWFs. Unit performance analyses showed significantly better load capacity for utility and industrial boilers as the CWF feed coal ash content is reduced to 5% or 2.6%. In general, utility units had more attractive capacity limits and retrofit costs than the industrial boilers and process heaters studied. Economic analyses indicated that conversion to CWF firing generally becomes feasible when differential fuel costs are above $1.00/10{sup 6}Btu. 60 figs., 24 tabs.

  13. Navajo Coal Combustion and Respiratory Health Near Shiprock, New Mexico

    PubMed Central

    Bunnell, Joseph E.; Garcia, Linda V.; Furst, Jill M.; Lerch, Harry; Olea, Ricardo A.; Suitt, Stephen E.; Kolker, Allan

    2010-01-01

    Indoor air pollution has been identified as a major risk factor for acute and chronic respiratory diseases throughout the world. In the sovereign Navajo Nation, an American Indian reservation located in the Four Corners area of the USA, people burn coal in their homes for heat. To explore whether/how indoor coal combustion might contribute to poor respiratory health of residents, this study examined respiratory health data, identified household risk factors such as fuel and stove type and use, analyzed samples of locally used coal, and measured and characterized fine particulate airborne matter inside selected homes. In twenty-five percent of homes surveyed coal was burned in stoves not designed for that fuel, and indoor air quality was frequently found to be of a level to raise concerns. The average winter 24-hour PM2.5 concentration in 20 homes was 36.0 μg/m3. This is the first time that PM2.5 has been quantified and characterized inside Navajo reservation residents' homes. PMID:20671946

  14. Navajo Coal Combustion and Respiratory Health Near Shiprock, New Mexico

    DOE PAGESBeta

    Bunnell, Joseph E.; Garcia, Linda V.; Furst, Jill M.; Lerch, Harry; Olea, Ricardo A.; Suitt, Stephen E.; Kolker, Allan

    2010-01-01

    Indoormore » air pollution has been identified as a major risk factor for acute and chronic respiratory diseases throughout the world. In the sovereign Navajo Nation, an American Indian reservation located in the Four Corners area of the USA, people burn coal in their homes for heat. To explore whether/how indoor coal combustion might contribute to poor respiratory health of residents, this study examined respiratory health data, identified household risk factors such as fuel and stove type and use, analyzed samples of locally used coal, and measured and characterized fine particulate airborne matter inside selected homes. In twenty-five percent of homes surveyed coal was burned in stoves not designed for that fuel, and indoor air quality was frequently found to be of a level to raise concerns. The average winter 24-hour PM 2.5 concentration in 20 homes was 36.0  μ g/ m 3 . This is the first time that PM 2.5 has been quantified and characterized inside Navajo reservation residents' homes.« less

  15. Catalytic Unmixed Combustion of Coal with Zero Pollution

    SciTech Connect

    George Rizeq; Parag Kulkarni; Raul Subia; Wei Wei

    2005-12-01

    GE Global Research is developing an innovative energy-based technology for coal combustion with high efficiency and near-zero pollution. This Unmixed Combustion of coal (UMC-Coal) technology simultaneously converts coal, steam and air into two separate streams of high pressure CO{sub 2}-rich gas for sequestration, and high-temperature, high-pressure vitiated air for producing electricity in gas turbine expanders. The UMC process utilizes an oxygen transfer material (OTM) and eliminates the need for an air separation unit (ASU) and a CO{sub 2} separation unit as compared to conventional gasification based processes. This is the final report for the two-year DOE-funded program (DE-FC26-03NT41842) on this technology that ended in September 30, 2005. The UMC technology development program encompassed lab- and pilot-scale studies to demonstrate the UMC concept. The chemical feasibility of the individual UMC steps was established via lab-scale testing. A pilot plant, designed in a related DOE funded program (DE-FC26-00FT40974), was reconstructed and operated to demonstrate the chemistry of UMC process in a pilot-scale system. The risks associated with this promising technology including cost, lifetime and durability OTM and the impact of contaminants on turbine performance are currently being addressed in detail in a related ongoing DOE funded program (DE-FC26-00FT40974, Phase II). Results obtained to date suggest that this technology has the potential to economically meet future efficiency and environmental performance goals.

  16. Coal combustion science: Task 1, Coal char combustion: Task 2, Fate of mineral matter. Quarterly progress report, July--September 1993

    SciTech Connect

    Hardesty, D.R.; Hurt, R.H.; Davis, K.A.; Baxter, L.L.

    1994-07-01

    Progress reports are presented for the following tasks: (1) kinetics and mechanisms of pulverized coal char combustion and (2) fate of inorganic material during coal combustion. The objective of Task 1 is to characterize the combustion behavior of selected US coals under conditions relevant to industrial pulverized coal-fired furnaces. In Sandia`s Coal Combustion Laboratory (CCL), optical techniques are used to obtain high-resolution images of individual burning coal char particles and to measure, in situ, their temperatures, sizes, and velocities. Detailed models of combustion transport processes are then used to determine kinetic parameters describing the combustion behavior as a function of coal type and combustion environment. Partially reacted char particles are also sampled and characterized with advanced materials diagnostics to understand the critical physical and chemical transformations that influence reaction rates and burnout times. The ultimate goal of the task is the establishment of a data base of the high temperature reactivities of chars from strategic US coals, from which important trends may be identified and predictive capabilities developed. The overall objectives for task 2 are: (1) to complete experimental and theoretical investigation of ash release mechanisms; (2) to complete experimental work on char fragmentation; (3) to establish the extent of coal (as opposed to char) fragmentation as a function of coal type and particle size; (4) to develop diagnostic capabilities for in situ, real-time, qualitative indications of surface species composition during ash deposition, with work continuing into FY94; (5) to develop diagnostic capabilities for in situ, real-time qualitative detection of inorganic vapor concentrations; and (6) to conduct a literature survey on the current state of understanding of ash deposition, with work continuing into FY94.

  17. Combustion characterization of the blend of plant coal and recovered coal fines. Technical report, December 1, 1991--February 29, 1992

    SciTech Connect

    Singh, S.; Scaroni, A.; Miller, B.; Choudhry, V.

    1992-08-01

    The overall objective of this proposed research program is to determine the combustion characteristics of the blend derived from mixing a plant coal and recovered and clean coal fines from the pond. During this study, one plant coal and three blend samples will be prepared and utilized. The blend samples will be of a mixture of 90% plant coal + 10% fines, 85% plant coal + 15% fines, 80% plant coal + 20% fines having particle size distribution of 70% passing through -200 mesh size. These samples` combustion behavior will be examined in two different furnaces at Penn State University, i.e., a down-fired furnace and a drop-tube furnace. The down-fired furnace will be used mainly to measure the emissions and ash deposition study, while the drop tube furnace will be used to determine burning profile, combustion efficiency, etc.

  18. Burning of suspended coal-water slurry droplet with oil as combustion additive. Final report

    SciTech Connect

    Yao, S.C.

    1984-10-01

    The combustion of single coal-water slurry droplet with oil as combustion additive (CWOM) has been studied. In this study, the droplet is suspended on a fine quartz fiber and is exposed to the hot combustion product of propane (C/sub 3/H/sub 8/) and air. The results are documented in a movie series. The combustion of CWOM with various combinations of concentrations are compared with that of coal-water slurry and water-oil mixture droplets. The combustion of coal-water slurry is enhanced significantly due to the presence of emulsified kerosene. The enhancement is also dependent upon the mixing procedure during preparation of CWOM. The presence of emulsified kerosene induces local boil-off and combustion that coal particles are splashed as fire works during the early evaporation stage of droplet heat-up. After particle splashing, blow-holes appear on the droplet surface. The popcorn and swelling phenomena usually occurred in coal-water-slurry combustion is greatly reduced. Significant combustion enhancement occurs with the use of kerosene in an amount of about 15 percent of the overall CWOM. This process of using kerosene as combustion additive may provide obvious advantage for the combustion of bituminous coal-water slurry. 4 references, 6 figures.

  19. Remediation of abandoned mines using coal combustion by-products

    SciTech Connect

    Bulusu, S.; Aydilek, A.H.; Petzrick, P.; Guynn, R.

    2005-08-01

    Acid mine drainage (AMD) is a phenomenon that occurs when pyrite that is present in abandoned coal mines comes in contact with oxygen and water, which results in the formation of sulfuric acid and iron hydroxide. Grouting of an abandoned mine with alkaline materials provides a permanent reduction in acid production. This study investigates the success of coal combustion by-product (CCB)-based grout mixtures in reducing AMD. The laboratory phase included testing of grouts with different proportions of Class F fly ash, flue gas desulfurization by-product, fluidized bed combustion by-product, and quicklime, for slump, modified flow, bleed, and strength. Then the selected optimal grout mixture was injected into the Frazee mine, located in Western Maryland. Pre- and post-injection water quality data were collected to assess the long-term success of the grouting operation by analyzing mine water, surface water, and groundwater. Overall, the results indicated that CCB-based grouts can control the acid mine drainage. However, the mechanical properties of the grout are highly critical for the construction phase, and long-term monitoring is essential for evaluating the effectiveness of the grouting process.

  20. Co-combustion of sludge with coal or wood

    SciTech Connect

    Leckner, B.; Aamand, L.-E.

    2004-07-01

    There are several options for co-combustion of biomass or waste with coal. In all cases the fuel properties are decisive for the success of the arrangement: contents of volatile matter and of potential emission precursors, such as sulphur, nitrogen, chlorine, and heavy metals. The content of alkali in the mineral substance of the fuel is important because of the danger of fouling and corrosion. Research activities at Chalmers University of Technology include several aspects of the related problems areas. An example is given concerning emissions from co-combustion in circulating fluidized beds with coal or wood as base fuels, and with sewage sludge as additional fuel. Two aspects of the properties of sludge are studied: emissions of nitrogen and sulphur oxides as well as of chlorine, because the contents of the precursors to these emissions are high. The possibility of utilizing the phosphorus in sludge as a fertilizer is also discussed. The results show that emissions can be kept below existing emission limits if the fraction of sludge is sufficiently small but the concentration of trace elements in the sludge ash prevents the sludge from being used as a fertilizer. 15 refs., 9 figs., 2 tabs.

  1. Combustion and fuel characterization of coal-water fuels

    SciTech Connect

    Beal, H.R.; Gralton, G.W.; Gronauer, T.W.; Liljedahl, G.N.; Love, B.F.

    1987-06-01

    Activities conducted under this contract include studies on the combustion and fireside behavior of numerous coal-water fuels (CWFs). The work has been broken down into the following areas: Task 1 -- Selection of Candidate Fuels; Task 2 -- Bench Scale Tests; Task 3 -- CWF Preparation and Supply; Task 4 -- Combustion Characterization; Task 5 -- Ash Deposition and Performance Testing; Task 6 -- Commercial Applications. This report covers Task 6, the study of commercial applications of CWFs as related to the technical and economic aspects of the conversion of existing boilers and heaters to CWF firing. This work involves the analysis of seven units of various sizes and configurations firing several selected CWFs. Three utility boilers, two industrial boilers, and two process heater designs are included. Each of the units was considered with four primary selected CWFs. A fifth fuel was considered for one of the utility units. A sixth fuel, a microfine grind CWF, was evaluated on two utility units and one industrial unit. The particular fuels were chosen with the objective of examining the effects of coal source, ash level, ash properties, and beneficiation on the CWF performance and economics of the seven units. 10 refs., 81 figs., 80 tabs.

  2. Investigation of black and brown carbon multiple-wavelength-dependent light absorption from biomass and fossil fuel combustion source emissions

    NASA Astrophysics Data System (ADS)

    Olson, Michael R.; Victoria Garcia, Mercedes; Robinson, Michael A.; Van Rooy, Paul; Dietenberger, Mark A.; Bergin, Michael; Schauer, James Jay

    2015-07-01

    Quantification of the black carbon (BC) and brown carbon (BrC) components of source emissions is critical to understanding the impact combustion aerosols have on atmospheric light absorption. Multiple-wavelength absorption was measured from fuels including wood, agricultural biomass, coals, plant matter, and petroleum distillates in controlled combustion settings. Filter-based absorption measurements were corrected and compared to photoacoustic absorption results. BC absorption was segregated from the total light extinction to estimate the BrC absorption from individual sources. Results were compared to elemental carbon (EC)/organic carbon (OC) concentrations to determine composition's impact on light absorption. Multiple-wavelength absorption coefficients, Angstrom exponent (6.9 to <1.0), mass absorption cross section (MAC), and Delta C (97 µg m-3 to ~0 µg m-3) were highly variable. Sources such as incense and peat emissions showed ultraviolet wavelength (370 nm) BrC absorption over 175 and 80 times (respectively) the BC absorption but only 21 and 11 times (respectively) at 520 nm wavelength. The bulk EC MACEC, λ (average at 520 nm = 9.0 ± 3.7 m2 g-1; with OC fraction <0.85 = ~7.5 m2 g-1) and the BrC OC mass absorption cross sections (MACBrC,OC,λ) were calculated; at 370 nm ultraviolet wavelengths; the MACBrC,OC,λ ranged from 0.8 m2 g-1 to 2.29 m2 g-1 (lowest peat, highest kerosene), while at 520 nm wavelength MACBrC,OC,λ ranged from 0.07 m2 g-1 to 0.37 m2 g-1 (lowest peat, highest kerosene/incense mixture). These MAC results show that OC content can be an important contributor to light absorption when present in significant quantities (>0.9 OC/TC), source emissions have variable absorption spectra, and nonbiomass combustion sources can be significant contributors to BrC.

  3. Possible criteria for establishing the quality and efficiency of coal combustion

    SciTech Connect

    Repic, B.S.; Jovanovic, M.P.; Saijnikov, A.V.

    1998-07-01

    Experimental results of pulverized coal combustion and possible criteria for establishing its quality and efficiency are presented in the paper. Experimental investigations of combustion of several types of coals (lignite, sub-bituminous, bituminous) were conducted at the experimental facility using movable blocks swirl burner. For estimation of quality and efficiency of coal combustion, apart from subjective evaluation and measurements in flame, two criteria were used, reactivity index (inverse of fuel number) and so-called pore resistance number. Rankings of investigated coals, based both on experimental results and the values of mentioned criteria, show quite good agreement and point out the possibility of wider use of these criteria.

  4. Ash transformations in the real-scale pulverized coal combustion of South African and Colombian coals

    SciTech Connect

    Lind, T.; Kauppinen, E.I.; Valmari, T.; Klippel, N.; Mauritzson, C.

    1996-12-31

    In this work, the formation of ash particles in the combustion of South African Klein Kropie coal and a Colombian coal was studied by measuring the ash particle characteristics upstream of the electrostatic precipitator (ESP) at a 510 MW{sub e} pulverized coal fired power plant. The authors measured the ash particle mass size distributions in the size range 0.01--50 {micro}m using low-pressure impactors and precutter cyclones. Also, samples were collected for computer controlled scanning electron microscopy (CCSEM) with a cyclone with an aerodynamic cut-diameter of about 1 {micro}m. The cyclone-collected samples were analyzed with standard CCSEM procedure by depositing the particles on a filter, and by embedding the particles in epoxy hence acquiring the cross-section analysis of the sample. All major mineral classes in both coals were found to undergo extensive coalescence during combustion. Iron, calcium and magnesium rich particles resulting from the decomposition of pyrite, calcite and dolomite were found to coalesce with quartz and aluminosilicate particles. The size distributions of the fly ash determined with CCSEM and low-pressure impactor-cyclone sampler were found to be similar.

  5. Investigation on thermal and trace element characteristics during co-combustion biomass with coal gangue.

    PubMed

    Zhou, Chuncai; Liu, Guijian; Fang, Ting; Lam, Paul Kwan Sing

    2014-11-01

    The thermochemical behaviors during co-combustion of coal gangue (CG), soybean stalk (SS), sawdust (SD) and their blends prepared at different ratios have been determined via thermogravimetric analysis. The simulate experiments in a fixed bed reactor were performed to investigate the partition behaviors of trace elements during co-combustion. The combustion profiles of biomass was more complicated than that of coal gangue. Ignition property and thermal reactivity of coal gangue could be enhanced by the addition of biomass. No interactions were observed between coal gangue and biomass during co-combustion. The volatilization ratios of trace elements decrease with the increasing proportions of biomass in the blends during co-combustion. Based on the results of heating value, activation energy, base/acid ratio and gaseous pollutant emissions, the blending ratio of 20-30% biomass content is regarded as optimum composition for blending and could be applied directly at current combustion application with few modifications. PMID:25459855

  6. REDUCTION OF NOx EMISSION FROM COAL COMBUSTION THROUGH OXYGEN ENRICHMENT

    SciTech Connect

    Western Research Institute

    2006-07-01

    BOC Process Gas Solutions and Western Research Institute (WRI) conducted a pilot-scale test program to evaluate the impact of oxygen enrichment on the emissions characteristics of pulverized coal. The combustion test facility (CTF) at WRI was used to assess the viability of the technique and determine the quantities of oxygen required for NOx reduction from coal fired boiler. In addition to the experimental work, a series of Computational Fluid Dynamics (CFD) simulations were made of the CTF under comparable conditions. A series of oxygen enrichment test was performed using the CTF. In these tests, oxygen was injected into one of the following streams: (1) the primary air (PA), (2) the secondary air (SA), and (3) the combined primary and secondary air. Emission data were collected from all tests, and compared with the corresponding data from the baseline cases. A key test parameter was the burner stoichiometry ratio. A series of CFD simulation models were devised to mimic the initial experiments in which secondary air was enriched with oxygen. The results from these models were compared against the experimental data. Experimental evidence indicated that oxygen enrichment does appear to be able to reduce NOx levels from coal combustion, especially when operated at low over fire air (OFA) levels. The reductions observed however are significantly smaller than that reported by others (7-8% vs. 25-50%), questioning the economic viability of the technique. This technique may find favor with fuels that are difficult to burn or stabilize at high OFA and produce excessive LOI. While CFD simulation appears to predict NO amounts in the correct order of magnitude and the correct trend with staging, it is sensitive to thermal conditions and an accurate thermal prediction is essential. Furthermore, without development, Fluent's fuel-NO model cannot account for a solution sensitive fuel-N distribution between volatiles and char and thus cannot predict the trends seen in the

  7. Humic substances and nitrogen-containing compounds from low rank brown coals

    SciTech Connect

    Demirbas, A.; Kar, Y.; Deveci, H.

    2006-03-15

    Coal is one of the sources of nitrogen-containing compounds (NCCs). Recovery of NCCs from brown coals in high yield was carried out from tars of stepwise semicoking of brown coals. Humic acids have been shown to contain many types of nitrogen compounds. Humic acids are thought to be complex aromatic macromolecules with amino acids, amino sugars, peptides, and aliphatic compounds that are involved in the linkages between the aromatic groups. Humic acids extracted from peats, brown coals, and lignites, are characterized using different techniques. Humic substances (HSs) have several known benefits to agriculture. The properties of humic substances vary from source to source, because they are heterogeneous mixtures of biochemical degradation products from plant and animal residues, and synthesis activities of microorganisms. HSs have been considered to be a significant floculant in surface water filtration plants for the production of drinking water as well as the processing of water. HSs are produced from chemical and biological degradation of plant and animal residues and from synthetic activities of microorganisms.

  8. Physicochemical characterizations of limestone for fluidized-bed coal combustion

    SciTech Connect

    Fuller, E.L. Jr.; Yoos, T.R. III; Walia, D.S.

    1981-05-01

    This study is an investigation of the physicochemical characteristics of three limestone samples, Quincy limestone (-20 + 60), Franklin limestone (-12 + 30), and Franklin limestone (-6 + 16), currently being tested at Oak Ridge National Laboratory for use in a fluidized-bed coal combustion unit. By correlating the chemistry, mineralogy, and surface area of these samples with empirical data obtained at Argonne National Laboratory, the sulfur capture ability and performance of these limestones can be loosely predicted. X-ray fluorescence and neutron activation analysis revealed a very high calcium content and very low concentrations of other elements in the three samples. X-ray diffraction patterns and petrographic examination of the limestone grains detected essentially no dolomite in the Quincy limestone or the fine Franklin limestone samples. The coarse Franklin limestone sample showed dolomite to be present in varying amounts up to maximum of 2.75%. Limited surface chemistry investigations of the samples were undertaken. Limestone and dolostone resources of the Tennessee Valley Authority region are widespread and abundant, and judged sufficient to meet industrial demand for many years. No problems are anticipated in securing limestone or dolostone supplies for a commercial fluidized-bed combustion plant in the Tennessee Valley Authority region. Transportation facilities and costs for limestone or dolostone will influence the siting of such a commercial fluidized-bed combustion plant. The most promising location in the Tennessee Valley Authority region at this time is Paducah, Kentucky.

  9. Transformations of inorganic coal constituents in combustion systems

    SciTech Connect

    Boni, A.A.; Helble, J.J.; Srinivasachar, S.; Wilemski, G. ); Sarofim, A.F.; Beer, J.M. ); Peterson, T.W.; Wendt, J.O.L. ); Huffman, G.P.; Huggins, F.E. )

    1990-11-01

    Objectives of this project are: (1) define the partitioning of inorganic constituents associated with raw coal particles among products (including vapors, aerosols, and residual char/ash particles) formed under conditions representative of pulverized coal flames as a function of the specific (intrinsic and extrinsic) characteristics of the raw coal and the environment in which the transformations occur; and (2) characterize the resultant spectrum of products in detail; elucidate and quantify the fundamental processes by which transformations of the inorganic constituents occur; and develop, based on the information required in a. and b. above, a tractable process'' model capable of predicting the significant features of the transformation process, most importantly, the nature and distribution of products. The work discussed highlights recent accomplishments in modeling synthetic char particle combustion times and temperatures with allowance for oxygen dissociation in the char boundary layer; in developing a continuum model for residual ash information and char fragmentation, permitting a more detailed time-resolved study of ash coalescence within a burning char particle; and in continuing development of the engineering model for ash particle formation. 40 refs., 25 figs., 10 tabs.

  10. Toxic substances from coal combustion -- A comprehensive assessment

    SciTech Connect

    C.L. Senior; T. Panagiotou; F.E. Huggins; G.P. Huffman; N. Yap; J.O.L. Wendt; W. Seames; M.R. Ames; A.F Sarofim; J. Lighty; A. Kolker; R. Finkelman; C.A. Palmer; S.J. Mroczkowsky; J.J. Helble; R. Mamani-Paco

    1999-11-01

    The Clean Air Act Amendments of 1990 identify a number of hazardous air pollutants (HAPs) as candidates for regulation. Should regulations be imposed on HAP emissions from coal-fired power plants, a sound understanding of the fundamental principles controlling the formation and partitioning of toxic species during coal combustion will be needed. With support from the Federal Energy Technology Center (FETC), the Electric Power Research Institute, and VTT (Finland), Physical Sciences Inc. (PSI) has teamed with researchers from USGS, MIT, the University of Arizona (UA), the University of Kentucky (UK), the University of Connecticut (UC), the University of Utah (UU) and the University of North Dakota Energy and Environmental Research Center (EERC) to develop a broadly applicable emissions model useful to regulators and utility planners. The new Toxics Partitioning Engineering Model (ToPEM) will be applicable to all combustion conditions including new fuels and coal blends, low-NOx combustion systems, and new power generation plants. Development of ToPEM will be based on PSI's existing Engineering Model for Ash Formation (EMAF). This report covers the reporting period from 1 July 1999 to 30 September 1999. During this period the MIT INAA procedures were revised to improve the quality of the analytical results. Two steps have been taken to reduce the analytical errors. A new nitric acid leaching procedure, modified from ASTM procedure D2492, section 7.3.1 for determination of pyritic sulfur, was developed by USGS and validated. To date, analytical results have been returned for all but the last complete round of the four-step leaching procedure. USGS analysts in Denver have halted development of the cold vapor atomic fluorescence technique for mercury analysis procedure in favor of a new direct analyzer for Hg that the USGS is in the process of acquiring. Since early June, emphasis at USGS has been placed on microanalysis of clay minerals in project coals in preparation

  11. Coal combustion science quarterly progress report, October--December 1992. Task 1, Coal char combustion [and] Task 2, Fate of mineral matter

    SciTech Connect

    Hardesty, D.R.; Hurt, R.H.; Baxter, L.L.

    1993-06-01

    In the Coal Combustion Laboratory (CCL) this quarter, controlled laboratory experiments were carried out to better understand the late stages of coal combustion and its relation to unburned carbon levels in fly ash. Optical in situ measurements were made during char combustion at high carbon conversions and the optical data were related to particle morphologies revealed by optical microscopy on samples extracted under the same conditions. Results of this work are reported in detail below. In the data presented below, we compare the fraction of alkali metal loss to that of the alkaline earth metals as a function of coal rank to draw conclusions about the mechanism of release for the latter. Figure 2.1 illustrates the fractional release of the major alkali and alkaline earth metals (Na, K, Ca, Mg) as a function of coal rank for a series of coals and for several coal blends. All data are derived from combustion experiments in Sandia`s Multifuel Combustor (MFC) and represent the average of three to eight experiments under conditions where the mass loss on a dry, ash-free (daf) basis exceeds 95 %. There are no missing data in the figure. The several coals with no indicated result exhibited no mass loss of the alkali or alkaline earth metals in our experiments. There is a clear rank dependence indicated by the data in Fig. 2.1, reflecting the mode of occurrence of the material in the coal.

  12. Mercury speciation and emissions from coal combustion in Guiyang, southwest China

    SciTech Connect

    Tang, S.L.; Feng, X.B.; Qiu, H.R.; Yin, G.X.; Yang, Z.C.

    2007-10-15

    Although China has been regarded as one of the largest anthropogenic mercury emission source with coal combustion, so far the actual measurements of Hg species and Hg emissions from the combustion and the capture of Hg in Chinese emission control devices were very limited. Aiming at Hg mercury species measurements in Guiyang, the capital city of Guizhou province in Southwest China, we studied flue gases of medium-to-small-sized industrial steam coal-firing boiler (10-30 t/h) with no control devices, medium-to-small-sized industrial steam coal-firing boiler with WFGD and large-scale coal combustion with ESPs using Ontario Hytro method. We obtained mercury emission factors of the three representative coal combustion and estimated mercury emissions in Guiyang in 2003, as well as the whole province from 1986 to 2002. Coal combustion in Guiyang emitted 1898 kg mercury to the atmosphere, of which 36% Hg is released from power plants, 41% from industrial coal combustion, and 23% from domestic users, and 267 kg is Hg{sup P}, 813 kg is Hg{sup 2+} and 817 kg is Hg{sup 0}. Mercury emission in Guizhou province increased sharply from 5.8 t in 1986 to 16.4 t in 2002. With the implementation of national economic strategy of China's Western Development, the annual mercury emission from coal combustion in the province is estimated to be about 32 t in 2015.

  13. Mercury speciation and emissions from coal combustion in Guiyang, Southwest China.

    PubMed

    Tang, Shunlin; Feng, Xinbin; Qiu, Jianrong; Yin, Guoxun; Yang, Zaichan

    2007-10-01

    Although China has been regarded as one of the largest anthropogenic mercury emission source with coal combustion, so far the actual measurements of Hg species and Hg emissions from the combustion and the capture of Hg in Chinese emission control devices were very limited. Aiming at Hg mercury species measurements in Guiyang, the capital city of Guizhou province in Southwest China, we studied flue gases of medium-to-small-sized industrial steam coal-firing boiler (10-30 t/h) with no control devices, medium-to-small-sized industrial steam coal-firing boiler with WFGD and large-scale coal combustion with ESPs using Ontario Hytro method. We obtained mercury emission factors of the three representative coal combustion and estimated mercury emissions in Guiyang in 2003, as well as the whole province from 1986 to 2002. Coal combustion in Guiyang emitted 1898 kg mercury to the atmosphere, of which 36% Hg is released from power plants, 41% from industrial coal combustion, and 23% from domestic users, and 267 kg is Hg(p), 813 kg is Hg(2+) and 817 kg is Hg0. Mercury emission in Guizhou province increased sharply from 5.8 t in 1986 to 16.4 t in 2002. With the implementation of national economic strategy of China's Western Development, the annual mercury emission from coal combustion in the province is estimated to be about 32 t in 2015. PMID:17517388

  14. Structural features of low rank coals with a tendency to spontaneous combustion

    SciTech Connect

    Artemov, A.V.; Saranchuk, V.I.; Semenenko, V.K.; Temerova, G.P.

    1983-01-01

    An investigation was made of the structural properties of low-rank Donets coals, including coals liable to spontaneous combustion. The coals showed marked differences in structure, elemental composition, aromaticity, organic sulphur and paramagnetic properties. During metamorphism, these structural differences tend to even out so that at the 80% carbon coalification stage, the chemical composition and structure of the coals susceptible to spontaneous combustion acquire a distinct similarity to those which are not susceptible, to the extent that the in-situ coal can no longer be considered self-heating.

  15. Recent advances in the use of synchrotron radiation for the analysis of coal combustion products

    SciTech Connect

    Manowitz, B.

    1995-11-01

    Two major coal combustion problems are the formation and build-up of slag deposits on heat transfer surfaces and the production and control of toxic species in coal combustion emissions. The use of synchrotron radiation for the analysis of coal combustion products can play a role in the better understanding of both these phenomena. An understanding of the chemical composition of such slags under boiler operating conditions and as a function of the mineral composition of various coals is one ultimate goal of this program. The principal constituents in the ash of many coals are the oxides of Si, Al, Fe, Ca, K, S, and Na. The analytical method required must be able to determine the functional forms of all these elements both in coal and in coal ash at elevated temperatures. One unique way of conducting these analyses is by x-ray spectroscopy.

  16. Evolution of Submicrometer Organic Aerosols during a Complete Residential Coal Combustion Process.

    PubMed

    Zhou, Wei; Jiang, Jingkun; Duan, Lei; Hao, Jiming

    2016-07-19

    In the absence of particulate matter (PM) control devices, residential coal combustion contributes significantly to ambient PM pollution. Characterizing PM emissions from residential coal combustion with high time resolution is beneficial for developing control policies and evaluating the environmental impact of PM. This study reports the evolution of submicrometer organic aerosols (OA) during a complete residential coal combustion process, that is, from fire start to fire extinction. Three commonly used coal types (bituminous, anthracite, and semicoke coals) were evaluated in a typical residential stove in China. For all three types of coal, the OA emission exhibited distinct characteristics in the four stages, that is, ignition, fierce combustion, relatively stable combustion, and ember combustion. OA emissions during the ignition stage accounted for 58.2-85.4% of the total OA emission of a complete combustion process. The OA concentration decreased rapidly during the fierce combustion stage and remained low during the relatively stable combustion stage. During these two stages, a significant ion peak of m/z 73 from organic acids were observed. The degree of oxidation of the OA increased from the first stage to the last stage. Implications for ambient OA source-apportionment and residential PM emission characterization and control are discussed. PMID:27298095

  17. Gob spontaneous combustion in a fully mechanized long-wall top-coal caving face

    SciTech Connect

    Xu, J.; Deng, J.; Zhang, X.; Guo, X.; Wen, F.

    1999-07-01

    As geological conditions allow, underground coal mines in China tend to use comprehensively mechanized roof-coal caving technique in an effort to gain a higher degree of mechanization at coal faces as well as higher coal production rates. As a face advances, a large amount of coal will be left behind in its gob area which may experience a self-enhancing process of coal oxidation and heat accumulation, ultimately leading to open fire. Such a self-enhancing coal spontaneous combustion process is a significantly impediment to mine safety and productivity. A sound mathematical model is an important step to predict the probability of spontaneous combustion so that measures against coal-heating can be adopted in time and at comparatively low cost. This paper analyzes main factors in coal spontaneous combustion process and proposes a mathematical model to describe the dynamic process of coal self-heating in the gob. This model has been applied to a coal production face in Datong Coal Region in Shangdong Province to satisfactorily predict the spontaneous combustion probability.

  18. APPLICATION OF ADVANCED TECHNOLOGY FOR NOX CONTROL: ALTERNATE FUELS AND FLUIDIZED-BED COAL COMBUSTION

    EPA Science Inventory

    The paper discusses the effect of alternate fuels and fluidized coal combustion in controlling the emission of nitrogen oxides (NOx). The current trend in energy use in the U.S. is toward greater use of coal and coal derived fuels, and on ensuring that these fuels are produced an...

  19. INVESTIGATION OF PRIMARY FINE PARTICULATE MATTER FROM COAL COMBUSTION BY COMPUTER-CONTROLLED SCANNING ELECTRON MICROSCOPY

    EPA Science Inventory

    The particle size distributions, morphologies, and chemical composition distributions of 14 coal fly ash (CFA) samples produced by the combustion of four western U.S. coals (two subbituminous, one lignite, and one bituminous) and three eastern U.S. coals (all bituminous) have bee...

  20. Formation of the pore structure of brown coal upon thermolysis with potassium hydroxide

    SciTech Connect

    T.G. Shendrik; Y.V. Tamarkina; T.V. Khabarova; V.A. Kucherenko; N.V. Chesnokov; B.N. Kuznetsov

    2009-07-01

    The pore-structure characteristics of active carbons prepared by the thermolysis (800{sup o}C) of brown coal impregnated with potassium hydroxide were studied. The dependence of the specific surface area, total pore volume, micropore volume, micropore fraction, and micropore size distribution on the KOH/coal weight ratio R{sub KOH}{le} 1.0 g/g was found. Condensation processes with the formation of a low-porosity material were predominant at low ratios of R{sub KOH} {le} 0.1 g/g. The development of a micropore structure was observed at R{sub KOH} {ge} 0.1 g/g, and it increased as R{sub KOH} was increased to 1.0 g/g. It was hypothesized that pore formation was due to the thermally initiated reactions of the structural fragments of coal with KOH molecules, which occurred within the framework of coal.

  1. Advances in measurements and simulation of gas-particle flows and coal combustion in burners/combustors

    NASA Astrophysics Data System (ADS)

    Zhou, L. X.

    2009-02-01

    Innovative coal combustors were developed, and measurement and simulation of gas-particle flows and coal combustion in such combustors were done in the Department of Engineering Mechanics, Tsinghua University. LDV/PDPA measurements are made to understand the behavior of turbulent gas-particle flows in coal combustors. Coal combustion test was done for the non-slagging cyclone coal combustor. The full two-fluid model developed by the present author was used to simulate turbulent gas-particle flows, coal combustion and NOx formation. It is found by measurements and simulation that the optimum design can give large-size recirculation zones for improving the combustion performance for all the combustors. The combustion test shows that the nonslagging coal combustor can burn 3-5mm coal particles with good combustion efficiency and low NO emission. Simulation in comparison with experiments indicates that the swirl number can significantly affect the NO formation in the swirl coal combustor.

  2. Naturally Occurring Radioactive Materials in Coals and Coal Combustion Residuals in the United States.

    PubMed

    Lauer, Nancy E; Hower, James C; Hsu-Kim, Heileen; Taggart, Ross K; Vengosh, Avner

    2015-09-15

    The distribution and enrichment of naturally occurring radioactive materials (NORM) in coal combustion residuals (CCRs) from different coal source basins have not been fully characterized in the United States. Here we provide a systematic analysis of the occurrence of NORM ((232)Th, (228)Ra, (238)U, (226)Ra, and (210)Pb) in coals and associated CCRs from the Illinois, Appalachian, and Powder River Basins. Illinois CCRs had the highest total Ra ((228)Ra + (226)Ra = 297 ± 46 Bq/kg) and the lowest (228)Ra/(226)Ra activity ratio (0.31 ± 0.09), followed by Appalachian CCRs (283 ± 34 Bq/kg; 0.67 ± 0.09), and Powder River CCRs (213 ± 21 Bq/kg; 0.79 ± 0.10). Total Ra and (228)Ra/(226)Ra variations in CCRs correspond to the U and Th concentrations and ash contents of their feed coals, and we show that these relationships can be used to predict total NORM concentrations in CCRs. We observed differential NORM volatility during combustion that results in (210)Pb enrichment and (210)Pb/(226)Ra ratios greater than 1 in most fly-ash samples. Overall, total NORM activities in CCRs are 7-10- and 3-5-fold higher than NORM activities in parent coals and average U.S. soil, respectively. This study lays the groundwork for future research related to the environmental and human health implications of CCR disposal and accidental release to the environment in the context of this elevated radioactivity. PMID:26328894

  3. Composition of the wax fraction of bitumen from methylated brown coals

    SciTech Connect

    S.I. Zherebtsov; A.I. Moiseev

    2009-04-15

    Changes in the group and individual compositions of the wax fractions of bitumen in the course of brown coal methylation were studied. With the use of IR and NMR spectroscopy and chromatography-mass spectrometry, it was found that the esters of methylated coal waxes consisted of the native esters of fatty acids and the methyl esters of these acids formed as a result of an alkylation treatment. Esterification and transesterification were predominant among the reactions of aliphatic fraction components. A positive effect of methanol alkylation on an increase in the yield of the aliphatic fractions was found.

  4. Properties of the solid thermolysis products of brown coal impregnated with an alkali

    SciTech Connect

    Yu.V. Tamarkina; L.A. Bovan; V.A. Kucherenko

    2008-08-15

    The mechanism of formation of a porous active carbon framework is considered, and the properties of the solid thermolysis products of brown coal (Aleksandriisk deposit, Ukraine) with potassium hydroxide are studied. The yields of the solid thermolysis products and potassium humates, the rate of the interaction of the solid thermolysis products with KOH at 700-900{sup o}C, the specific surface areas, the adsorption capacities for methylene blue and iodine, and the specific activities of surface areas are determined under variation of the KOH/coal ratio KOH < 18 mol/kg and temperature (110-900{sup o}C).

  5. Palynostratigraphy of the Erkovtsy field of brown coal (the Zeya-Bureya sedimentary basin)

    SciTech Connect

    Kezina, T.V.; Litvinenko, N.D.

    2007-08-15

    The Erkovtsy brown coal field in the northwestern Zeya-Bureya sedimentary basin (129-130{sup o}E, 46-47{sup o}N) is structurally confined to southern flank of the Mesozoic-Cenozoic Belogor'e depression. The verified stratigraphic scheme of the coalfield sedimentary sequence is substantiated by palynological data on core samples from 18 boreholes sampled in the course of detailed prospecting and by paleobotanical analysis of sections in the Yuzhnyi sector of the coalfield (data of 1998 by M.A. Akhmetiev and S.P. Manchester). Sections of the Erkovtsy, Arkhara-Boguchan, and Raichikha brown-coal mines are correlated. Stratigraphic subdivisions distinguished in the studied sedimentary succession are the middle and upper Tsagayan subformations (the latter incorporating the Kivda Beds), Raichikha, Mukhino, Buzuli, and Sazanka formations.

  6. Combustion characterization of the blend of plant coal and recovered coal fines. Technical report, September 1--November 30, 1991

    SciTech Connect

    Singh, Shyam

    1991-12-31

    The overall objective of this proposed research program is to determine the combustion characteristics of the blend derived from mixing a plant coal and recovered and clean coal fines from the pond. During this study, one plant coal and three blend samples will be prepared and utilized. The blend samples will be of a mixture of 90% plant coal + 10% fines, 85% plant coal + 15% fines, 80% plant coal + 20% fines having particle size distribution of 70% passing through {minus}200 mesh size. These samples` combustion behavior will be examined in two different furnaces at Penn State University, i.e., a down-fired furnace and a drop-tube furnace. The down-fired furnace will be used mainly to measure the emissions and ash deposition study, while the drop tube furnace will be used to determine burning profile, combustion efficiency, etc. This report covers the first quarter`s progress. Major activities during this period were focused on finding the plants where a demo MTU column will be installed to prepare the samples needed to characterize the combustion behavior of slurry effluents. Also, a meeting was held at Penn State University to discuss the availability of the laboratory furnace for testing the plant coal/recovered coal fines blends.

  7. Ignition and devolatilization of pulverized bituminous coal particles during oxygen/carbon dioxide coal combustion

    SciTech Connect

    Alejandro Molina; Christopher R. Shaddix

    2007-07-01

    Oxygen/carbon dioxide recycle coal combustion is actively being investigated because of its potential to facilitate CO{sub 2} sequestration and to achieve emission reductions. In the work reported here, the effect of enhanced oxygen levels and CO{sub 2} bath gas is independently analyzed for their influence on single-particle pulverized coal ignition of a U.S. eastern bituminous coal. The experiments show that the presence of CO{sub 2} and a lower O{sub 2} concentration increase the ignition delay time but have no measurable effect on the time required to complete volatile combustion, once initiated. For the ignition process observed in the experiments, the CO{sub 2} results are explained by its higher molar specific heat and the O{sub 2} results are explained by the effect of O{sub 2} concentration on the local mixture reactivity. Particle ignition and devolatilization properties in a mixture of 30% O{sub 2} in CO{sub 2} are very similar to those in air. 23 refs., 8 figs., 1 tab.

  8. Combustion characterization of beneficiated coal-based fuels. Quarterly report No. 17, April--June 1993

    SciTech Connect

    Chow, O.K.; Nsakala, N.Y.

    1993-08-01

    Pittsburgh Energy Technology Center of the US Department of Energy has contracted with Combustion Engineering, Inc. (CE) to perform a five-year project on ``Combustion Characterization of Beneficiated Coal-Based Fuels.`` The beneficiated coals are produced by other contractors under the DOE Coal Preparation Program. Several contractor-developed advanced coal cleaning processes are run at pilot-scale cleaning facilities to produce 20-ton batches of fuels for shipment to CE`s laboratory in Windsor, Connecticut. CE then processes the products into either a coal-water fuel (CWF) or a dry microfine pulverized coa1 (DMPC) form for combustion testing. The objectives of this project include: (1) the development of an engineering data base which will provide detailed information on the properties of BCFs influencing combustion, ash deposition, ash erosion, particulate collection, and emissions; and (2) the application of this technical data base to predict the performance and economic impacts of firing the BCFs in various commercial boiler designs. The technical approach used to develop the technical data includes: bench-scale fuel property, combustion, and ash deposition tests; pilot-scale combustion and ash effects tests; and full-scale combustion tests. During the third quarter of 1993, the following technical progress was made: Completed modeling calculations of coal mineral matter transformations, deposition behavior, and heat transfer impacts of six test fuels; and ran pilot-scale tests of Upper Freeport feed coal, microagglomerate product, and mulled product.

  9. JV Task 108 - Circulating Fluidized-Bed Combustion and Combustion Testing of Turkish Tufanbeyli Coal

    SciTech Connect

    Douglas Hajicek; Jay Gunderson; Ann Henderson; Stephen Sollom; Joshua Stanislowski

    2007-08-15

    Two combustion tests were performed at the Energy & Environmental Research Center (EERC) using Tufanbeyli coal from Turkey. The tests were performed in a circulating fluidized-bed combustor (CFBC) and a pulverized coal-fired furnace, referred to as the combustion test facility (CTF). One of the goals of the project was to determine the type of furnace best suited to this coal. The coal is high in moisture, ash, and sulfur and has a low heating value. Both the moisture and the sulfur proved problematic for the CTF tests. The fuel had to be dried to less than 37% moisture before it could be pulverized and further dried to about 25% moisture to allow more uniform feeding into the combustor. During some tests, water was injected into the furnace to simulate the level of flue gas moisture had the fuel been fed without drying. A spray dryer was used downstream of the baghouse to remove sufficient sulfur to meet the EERC emission standards permitted by the North Dakota Department of Health. In addition to a test matrix varying excess air, burner swirl, and load, two longer-term tests were performed to evaluate the fouling potential of the coal at two different temperatures. At the lower temperature (1051 C), very little ash was deposited on the probes, but deposition did occur on the walls upstream of the probe bank, forcing an early end to the test after 2 hours and 40 minutes of testing. At the higher temperature (1116 C), ash deposition on the probes was significant, resulting in termination of the test after only 40 minutes. The same coal was burned in the CFBC, but because the CFBC uses a larger size of material, it was able to feed this coal at a higher moisture content (average of 40.1%) compared to the CTF (ranging from 24.2% to 26.9%). Sulfur control was achieved with the addition of limestone to the bed, although the high calcium-to-sulfur rate required to reduce SO{sub 2} emissions resulted in heat loss (through limestone calcination) and additional ash

  10. Removal of mercury from coal-combustion flue gas

    SciTech Connect

    Livengood, C.D.; Huang, H.S.; Mendelsohn, M.H.; Wu, J.M.

    1995-12-31

    Combustion sources, including those using coal for fuel, contribute a significant fraction of total anthropogenic mercury emissions. Recent field studies have shown that current flue-gas cleanup (FGC) systems are relatively ineffective in controlling elemental mercury, which is a major component of the mercury emissions for many systems. Research at Argonne National Laboratory has been focused on techniques to enhance the capture of elemental mercury in existing FGC systems. For dry processes, these studies have included evaluation of activated carbons and investigation of sorbents based upon chemical pretreatment of low-cost mineral substrates. To enhance the ability of wet scrubbers to capture mercury, the studies have looked at the effects of improved mass transfer through both mechanical and chemical means, as well as the conversion of elemental mercury into more soluble species that can be easily absorbed.

  11. Thermally induced structural changes in coal combustion. Final report

    SciTech Connect

    Flagan, R.C.; Gavalas, G.R.

    1992-01-01

    The effects of the temperature-time history during coal devolitization and oxidation on the physical properties and the reactivity of resulting char were studied experimentally for temperatures and residence times typical of pulverized combustion. Experiments were also carried out at somewhat lower temperatures and correspondingly longer residence times. An electrically heated laminar flow reactor was used to generate char and measure the rates of oxidation at gas temperatures about 1600K. Partially oxidized chars were extracted and characterized by gas adsorption and mercury porosimetry, optical and scanning electron microscopy, and oxidation in a thermogravimetric analysis system (TGA). A different series of experiments was conducted using a quadrople electrodynamic balance. Single particles were suspended electrodynamically and heated by an infrared laser in an inert or oxygen-containing atmosphere. During the laser heating, measurements were taken of particle mass, size/shape, and temperature.

  12. Removal of mercury from coal-combustion flue-gas

    SciTech Connect

    Livengood, C.D.; Huang, H.S.; Mendelsohn, M.H.; Wu, J.M.

    1995-12-01

    Combustion sources, including those using coal for fuel, contribute a significant fraction of total anthropogenic mercury emissions. Recent field studies have shown that current flue-gas cleanup (FGC) systems are relatively ineffective in controlling elemental mercury, which is a major component of the mercury emissions for many systems. Research at Argonne National Laboratory has been focused on techniques to enhance the capture of elemental mercury in existing FGC systems. For dry processes, these studies have included evaluation of activated carbons and investigation of sorbents based upon chemical pretreatment of low-cost mineral substrates. To enhance the ability of wet scrubbers to capture mercury, the studies have looked at the effects of improved mass transfer through both mechanical and chemical means, as well as the conversion of elemental mercury into more soluble species that can be easily absorbed.

  13. Volcanic ash in feed coal and its influence on coal combustion products

    SciTech Connect

    Brownfield, M.E.; Affolter, R.H.; Cathcart, J.D.; Brownfield, I.K.; Hower, J.C.; Stricker, G.D.; O'Connor, J.T.

    2000-07-01

    The US Geological Survey and the University of Kentucky Center for Applied Energy Research are collaborating with an Indiana Utility to determine the physical and chemical properties of feed coal and coal combustion products (CCPs) from a coal-fired power plant. The plant utilizes a low-sulfur (.23--.47 weight percent S) coal from the Powder River Basin, Wyoming. Scanning Electron Microscope (SEM) and X-ray diffraction (XRD) analysis of feed coal samples identified two mineral suites. A primary suite (not authigenic) consisting of quartz (detrital and volcanic beta-form grains), biotite, and minor zircon and a secondary authigenic mineral suite containing calcite, alumino-phosphates (crandallite and gorceixite), kaolinite, quartz, anatase, barite, and pyrite. The authigenic minerals are attributed to air-fall and reworked volcanic ash that was deposited in peat-forming mires. The Powder River Basin feed coals contain higher amounts of Ba, Ca, Mg, Na, Sr, and P compared to other analyzed eastern coals. These elements are associated with alumino-phosphate, biotite, calcite, and clay minerals. The element associations are indicative of coal that incorporated volcanic ash during deposition. XRD analysis of CCPs revealed a predominance of glass, perovskite, lime, gehlenite, quartz, and phosphates with minor amounts of periclase, anhydrite, hematite, and spinel group minerals in the fly ash; and quartz, plagioclase (albite and anorthite), pyroxene (augite and fassaite), rhodonite, and akermanite in the bottom ash. Microprobe and SEM analysis of fly ash samples revealed quartz, zircon, monazite, euhedral laths of corundum with merrillite, hematite, dendritic spinels/ferrites, and rounded grains of wollastonite with periclase. The abundant Ca and Mg mineral phases in the fly ashes are related to the presence of carbonate, clay, and phosphate minerals in the feed coal. The Ca- and Mg-rich mineral phases in the CCPs can be attributed to volcanic minerals deposited in the

  14. Studying the specific features pertinent to combustion of chars obtained from coals having different degrees of metamorphism and biomass chars

    NASA Astrophysics Data System (ADS)

    Bestsennyi, I. V.; Shchudlo, T. S.; Dunaevskaya, N. I.; Topal, A. I.

    2013-12-01

    Better conditions for igniting low-reaction coal (anthracite) can be obtained, higher fuel burnout ratio can be achieved, and the problem of shortage of a certain grade of coal can be solved by firing coal mixtures and by combusting coal jointly with solid biomass in coal-fired boilers. Results from studying the synergetic effect that had been revealed previously during the combustion of coal mixtures in flames are presented. A similar effect was also obtained during joint combustion of coal and wood in a flame. The kinetics pertinent to combustion of char mixtures obtained from coals characterized by different degrees of metamorphism and the kinetics pertinent to combustion of wood chars were studied on the RSK-1D laboratory setup. It was found from the experiments that the combustion rate of char mixtures obtained from coals having close degrees of metamorphism is equal to the value determined as a weighted mean rate with respect to the content of carbon. The combustion rate of char mixtures obtained from coals having essentially different degrees of metamorphism is close to the combustion rate of more reactive coal initially in the process and to the combustion rate of less reactive coal at the end of the process. A dependence of the specific burnout rate of carbon contained in the char of two wood fractions on reciprocal temperature in the range 663—833 K is obtained. The combustion mode of an experimental sample is determined together with the reaction rate constant and activation energy.

  15. Health effects of coal mining and combustion: carcinogens and cofactors.

    PubMed Central

    Falk, H L; Jurgelski, W

    1979-01-01

    Some polynuclear aromatics (PNA) have been found to be potent carcinogens for all tissues and organs of experimental animals that have been exposed to them, but different dose levels are needed for these effects. They have been known for decades to cause cancer at the site of application but also at certain sites distant from the area of contact. Although some hydrocarbons are potent and complete carcinogens, the majority of related hydrocarbons was originally found to be inactive. Since they generally appear together, it was important to know more about their interaction, particularly whether they would synergize, or antagonize. The polycyclic hydrocarbons have been studied by subcutaneous injection, where they prove very potent carcinogens. They are also very active on the skin of mice where they produce cancer on prolonged application. Inhalation studies, require larger doses yielded negative results until particulate matter was introduced which facilitated the development of lung tumors. Although iron oxide dust was used initially, other dusts were also capable of enhancing the response of the tissue to benzo(a)pyrene carcinogenesis. This point is of importance, particularly since the inhalation of PNA in situations of air pollution or coal mining involves particulates, although of a different type. Soot is not a homogenous substance and several factors determine its properties. Soots will lose some of the absorbed chemicals during their residence in air, but they retain their PNAs for long periods of time when they reach the soil. The carcinogenicity of PNAs in the adsorbed state may be completely absent, depending on particle size of the soot and availability of eluting capability of the tissues or cells in contact with the soot. Whenever the carcinogenic polynuclear aromatics can be eluted they will be active in producing cancer if their residence is adequate. There seems to be no reason to assume that a large increase in coal combustion in the future will

  16. Investigation of formation of nitrogen compounds in coal combustion. Final report

    SciTech Connect

    Blair, D.W.; Crane, I.D.; Wendt, J.O.L.

    1983-10-01

    This is the final report on DOE contract number DE-AC21-80MC14061. It concerns the formation of nitrogen oxide from fuel-bound nitrogen during coal combustion. The work reported was divided into three tasks. They addressed problems of time-resolving pyrolysis rates of coal under simulated combustion conditions, the combustion of the tar that results from such pyrolysis, and theoretical modeling of the pyrolysis process. In all of these tasks, special attention was devoted to the fate of coal nitrogen. The first two tasks were performed by Exxon Research and Engineering Company. 49 references.

  17. Theoretical principles of use of coal fractions with different densities for combustion

    SciTech Connect

    S.G. Gagarin; A.M. Gyul'maliev

    2009-02-15

    It is reasonable to complement the conventional preparation of steam coal involving the removal of ash components and pyritic sulfur by the isolation of the lightest organic fractions, which possess enhanced performance characteristics. These fractions are smoothly saleable both on the domestic and world markets for effective pulverized-coal combustion via new combustion technologies. Heavier (inertinite) fractions of the coal preparation concentrate marketed at lower prices can be considered appropriate fuel for burning in circulating fluidized-bed combustion systems. 13 refs., 5 figs., 4 tabs.

  18. Oxidation of Mercury in Products of Coal Combustion

    SciTech Connect

    Peter Walsh; Giang Tong; Neeles Bhopatkar; Thomas Gale; George Blankenship; Conrad Ingram; Selasi Blavo Tesfamariam Mehreteab; Victor Banjoko; Yohannes Ghirmazion; Heng Ban; April Sibley

    2009-09-14

    Laboratory measurements of mercury oxidation during selective catalytic reduction (SCR) of nitric oxide, simulation of pilot-scale measurements of mercury oxidation and adsorption by unburned carbon and fly ash, and synthesis of new materials for simultaneous oxidation and adsorption of mercury, were performed in support of the development of technology for control of mercury emissions from coal-fired boilers and furnaces. Conversion of gas-phase mercury from the elemental state to water-soluble oxidized form (HgCl{sub 2}) enables removal of mercury during wet flue gas desulfurization. The increase in mercury oxidation in a monolithic V{sub 2}O{sub 5}-WO{sub 3}/TiO{sub 2} SCR catalyst with increasing HCl at low levels of HCl (< 10 ppmv) and decrease in mercury oxidation with increasing NH{sub 3}/NO ratio during SCR were consistent with results of previous work by others. The most significant finding of the present work was the inhibition of mercury oxidation in the presence of CO during SCR of NO at low levels of HCl. In the presence of 2 ppmv HCl, expected in combustion products from some Powder River Basin coals, an increase in CO from 0 to 50 ppmv reduced the extent of mercury oxidation from 24 {+-} 3 to 1 {+-} 4%. Further increase in CO to 100 ppmv completely suppressed mercury oxidation. In the presence of 11-12 ppmv HCl, increasing CO from 0 to {approx}120 ppmv reduced mercury oxidation from {approx}70% to 50%. Conversion of SO{sub 2} to sulfate also decreased with increasing NH{sub 3}/NO ratio, but the effects of HCl and CO in flue gas on SO{sub 2} oxidation were unclear. Oxidation and adsorption of mercury by unburned carbon and fly ash enables mercury removal in a particulate control device. A chemical kinetic mechanism consisting of nine homogeneous and heterogeneous reactions for mercury oxidation and removal was developed to interpret pilot-scale measurements of mercury oxidation and adsorption by unburned carbon and fly ash in experiments at pilot

  19. Combustion characteristics of dry coal-powder-fueled adiabatic diesel engine: Final report

    SciTech Connect

    Kakwani, R.M.; Kamo, R.

    1989-01-01

    This report describes the progress and findings of a research program aimed at investigating the combustion characteristics of dry coal powder fueled diesel engine. During this program, significant achievements were made in overcoming many problems facing the coal-powder-fueled engine. The Thermal Ignition Combustion System (TICS) concept was used to enhance the combustion of coal powder fuel. The major coal-fueled engine test results and accomplishments are as follows: design, fabrication and engine testing of improved coal feed system for fumigation of coal powder to the intake air; design, fabrication and engine testing of the TICS chamber made from a superalloy material (Hastelloy X); design, fabrication and engine testing of wear resistant chrome oxide ceramic coated piston rings and cylinder liner; lubrication system was improved to separate coal particles from the contaminated lubricating oil; control of the ignition timing of fumigated coal powder by utilizing exhaust gas recirculation (EGR) and variable TICS chamber temperature; coal-fueled engine testing was conducted in two configurations: dual fuel (with diesel pilot) and 100% coal-fueled engine without diesel pilot or heated intake air; cold starting of the 100% coal-powder-fueled engine with a glow plug; and coal-fueled-engine was operated from 800 to 1800 rpm speed and idle to full load engine conditions.

  20. Treatment of chromic tannery wastes using coal ashes from fluidized bed combustion of coal

    SciTech Connect

    Bulewicz, E.M.; Kozak, A.; Kowalski, Z.

    1997-10-01

    A new method of treatment for chromic tannery wastes containing chrome and large amounts organic substances has been investigated. It has been found that the addition of certain types of coal ash from fluid bed combustion technologies, at a suitable temperature and pH, results in effective removal of Cr(III) compounds present in the wastes. The wastes could then be subjected to further processing in conventional biological treatment units. The method is very simple, cheap, and effective and could be used for chromic tannery wastes of different compositions.

  1. Toxic substances from coal combustion -- A comprehensive assessment

    SciTech Connect

    Senior, C.L.; Huggins, F.E.; Huffman, G.P.; Shan, N.; Yap, N.; Wendt, J.O.L.; Seames, W.; Ames, M.R.; Sarofim, A.F.; Swenson, S.; Lighty, J.; Kolker, A.; Finkelman, R.; Palmer, C.; Mroczkowski, S.; Helble, J.; Mamani-Paco, R.; Sterling, R.; Dunham, G.; Miller, S.

    2000-08-17

    The final program review meeting of Phase II was held on June 22 in Salt Lake City. The goals of the meeting were to present work in progress and to identify the remaining critical experiments or analyses, particularly those involving collaboration among various groups. The information presented at the meeting is summarized in this report. Remaining fixed bed, bench-scale experiments at EERC were discussed. There are more ash samples which can be run. Of particular interest are high carbon ash samples to be generated by the University of Arizona this summer and some ash-derived sorbents that EERC has evaluated on a different program. The use of separation techniques (electrostatic or magnetic) was also discussed as a way to understand the active components in the ash with respect to mercury. XAFS analysis of leached and unleached ash samples from the University of Arizona was given a high priority. In order to better understand the fixed bed test results, CCSEM and Moessbauer analyses of those ash samples need to be completed. Utah plans to analyze the ash from the single particle combustion experiments for those major elements not measured by INAA. USGS must still complete mercury analyses on the whole coals and leaching residues. Priorities for further work at the SHRIMP-RG facility include arsenic on ash surfaces and mercury in sulfide minerals. Moessbauer analyses of coal samples from the University of Utah were completed; samples from the top and bottom layers of containers of five different coals showed little oxidation of pyrite in the top relative to the bottom except for Wyodak.

  2. Preparation and combustion of coal-water fuel from the Sin Pun coal deposit, southern Thailand

    SciTech Connect

    1997-05-01

    In response to an inquiry by the Department of Mineral Resources in Thailand, the Energy & Environmental Research Center (EERC) prepared a program to assess the responsiveness of Sin Pun lignite to the temperature and pressure conditions of hot-water drying. The results indicate that drying made several improvements in the coal, notably increases in heating value and carbon content and reductions in equilibrium moisture and oxygen content. The equilibrium moisture content decreased from 27 wt% for the raw coal to about 15 wt% for the hot-water-dried (HWD) coals. The energy density for a pumpable coal-water fuel (CWF) indicates an increase from 4500 to 6100 Btu/lb by hot-water drying. Approximately 650 lb of HWD Sin Pun CWF were fired in the EERC`s combustion test facility. The fuel burned extremely well, with no feed problems noted during the course of the test. Fouling and slagging deposits each indicated a very low rate of ash deposition, with only a dusty layer formed on the cooled metal surfaces. The combustor was operated at between 20% and 25% excess air, resulting in a flue gas SO{sub 2} concentration averaging approximately 6500 parts per million.

  3. Mercury emissions from coal combustion in Silesia, analysis using geostatistics

    NASA Astrophysics Data System (ADS)

    Zasina, Damian; Zawadzki, Jaroslaw

    2015-04-01

    Data provided by the UNEP's report on mercury [1] shows that solid fuel combustion in significant source of mercury emission to air. Silesia, located in southwestern Poland, is notably affected by mercury emission due to being one of the most industrialized Polish regions: the place of coal mining, production of metals, stone mining, mineral quarrying and chemical industry. Moreover, Silesia is the region with high population density. People are exposed to severe risk of mercury emitted from both: industrial and domestic sources (i.e. small household furnaces). Small sources have significant contribution to total emission of mercury. Official and statistical analysis, including prepared for international purposes [2] did not provide data about spatial distribution of the mercury emitted to air, however number of analysis on Polish public power and energy sector had been prepared so far [3; 4]. The distribution of locations exposed for mercury emission from small domestic sources is interesting matter merging information from various sources: statistical, economical and environmental. This paper presents geostatistical approach to distibution of mercury emission from coal combustion. Analysed data organized in 2 independent levels: individual, bottom-up approach derived from national emission reporting system [5; 6] and top down - regional data calculated basing on official statistics [7]. Analysis, that will be presented, will include comparison of spatial distributions of mercury emission using data derived from sources mentioned above. Investigation will include three voivodeships of Poland: Lower Silesian, Opole (voivodeship) and Silesian using selected geostatistical methodologies including ordinary kriging [8]. References [1] UNEP. Global Mercury Assessment 2013: Sources, Emissions, Releases and Environmental Transport. UNEP Chemicals Branch, Geneva, Switzerland, 2013. [2] NCEM. Poland's Informative Inventory Report 2014. NCEM at the IEP-NRI, 2014. http

  4. Adsorption properties of carbon materials produced by thermolysis of brown coal in the presence of alkali metal hydroxides

    SciTech Connect

    Tamarkina, Y.V.; Maslova, L.A.; Khabarova, T.V.; Kucherenko, V.A.

    2008-07-15

    Activated carbons produced by thermolysis of brown coal impregnated with an alkali metal hydroxide MOH (M = Li, Na, K) at an MOH/coal ratio R-MOH = 80 mol kg{sup -1} were studied. Dependences of the adsorption capacities for iodine and Methylene Blue dye, specific surface area, and yield of activated carbons on the ratio R-MOH were obtained.

  5. Combustion characterization of beneficiated coal-based fuels. Quarterly report No. 6, July 1990--September 1990

    SciTech Connect

    Chow, O.K.; Nsakala, N.Y.

    1990-11-01

    The Pittsburgh Energy Technology Center of the US Department of Energy has contracted with Combustion Engineering, Inc. (CE) to perform a three-year project on ``Combustion Characterization of Beneficiated Coal-Based Fuels.`` The beneficiated coals are produced by other contractors under the DOE Coal Preparation Program. Several contractor-developed advanced coal cleaning processes are being run at the cleaning facility in Homer City, Pennsylvania, to produce 20-ton batches of fuels for shipment to CE`s laboratory in Windsor, Connecticut. CE then processes the products into either a coal-water fuel (CVVT) or a dry microfine pulverized coal (DMPC) form for combustion testing. The objectives of this project include: (1) the development of an engineering data base which will provide detailed information on the properties of BCFs influencing combustion, ash deposition, ash erosion, particulate collection, and emissions; and (2) the application of this technical data base to predict the performance and economic impacts of firing the BCFs in various commercial boiler designs. The technical approach used to develop the technical data includes: bench-scale fuel property, combustion, and ash deposition tests; pilot-scale combustion and ash effects tests; and full-scale combustion tests. Subcontractors to CE to perform parts of the test work are the Massachusetts Institute of Technology (MIT), Physical Science, Inc. Technology Company (PSIT) and the University of North Dakota Energy and Environmental Research Center (UNDEERC). Twenty fuels will be characterized during the three-year base program: three feed coals, fifteen BCFS, and two conventionally cleaned coals for full-scale tests. Approximately, nine BCFs will be in dry microfine coal (DMPC) form, and six BCFs will be in coal-water fuel (CWF) form. Additional BCFs would be characterized during optional project supplements.

  6. Optical Properties of Black and Brown Carbon Aerosols from Laboratory Combustion of Wildland Fuels

    NASA Astrophysics Data System (ADS)

    Beres, N. D.; Molzan, J.

    2015-12-01

    Aerosol light absorption in the solar spectral region (300 nm - 2300 nm) of the atmosphere is key for the direct aerosol radiative forcing, which is determined by aerosol single scattering albedo (SSA), asymmetry parameter, and by the albedo of the underlying surface. SSA is of key importance for the sign and quantity of aerosol direct radiative forcing; that is, does the aerosol make the earth look darker (heating) or whiter (cooling)? In addition, these optical properties are needed for satellite retrievals of aerosol optical depth and properties. During wildland fires, aerosol optical absorption is largely determined by black carbon (BC) and brown carbon (BrC) emissions. BC is strongly absorbing throughout the solar spectrum, while BrC absorption strongly increases toward shorter wavelength and can be neglected in the red and infrared. Optical properties of BrC emitted from wildland fires are poorly understood and need to be studied as function of fuel type and moisture content and combustion conditions. While much more is known about BC optical properties, knowledge for the ultraviolet (UV) spectral region is still lacking and critically needed for satellite remote sensing (e.g., TOMS, OMI) and for modeling of tropospheric photochemistry. Here, a project to better characterize biomass burning aerosol optical properties is described. It utilizes a laboratory biomass combustion chamber to generate aerosols through combustion of different wildland fuels of global and regional importance. Combustion aerosol optics is characterized with an integrating nephelometer to measure aerosol light scattering and a photoacoustic instrument to measure aerosol light absorption. These measurements will yield optical properties that are needed to improve qualitative and quantitative understanding of aerosol radiative forcing and satellite retrievals for absorbing carbonaceous aerosols from combustion of wildland fuels.

  7. Spontaneous-combustion studies of US coals. Rept. of Investigations/1987

    SciTech Connect

    Smith, A.C.; Lazzara, C.P.

    1987-01-01

    This report describes laboratory studies conducted by the Bureau of Mines on the spontaneous combustion of U.S. coals. Approximately 11 pct of U.S. underground-coal-mine fires are attributed to spontaneous combustion. The relative self-heating tendencies of 24 coal samples were evaluated in an adiabatic heating oven. Minimum self-heating temperatures (SHT's) in the oven ranged from 35/sup 0/C for a lignite and high-volatile C bituminous coal, to 135/sup 0/C for two low-volatile bituminous coals. The minimum SHT's of two coals were determined, and the results were in good agreement with those found in the adiabatic oven. Finally, results of a test in the moderate-scale apparatus indicated a strong dependence of the self-heating rate of a low-rank coal on the moisture content of the air.

  8. Evaluation of the behavior of Colombian coals during the combustion in fixed bed

    SciTech Connect

    Giraldo, M.; Chejne, F.; Hill, A.

    2000-07-01

    The improvements in the technological processes that have coal as energy source must be based on the knowledge of physical and chemical properties of coal and in the knowledge of its evolution during the combustion process. These characteristics are involved in the coal behavior. Moreover, the coal porosity has an important relevance on the reaction rate and in diverse physical and chemical properties, and therefore, is a key parameter in the usefulness of coal. This project includes studies about Colombian coal combustion and its kinetic behavior. The coal was characterized and classified by particle size,and origin. In this research project, the physical and chemical properties of coal that affect its applicability in different kinds of technological processes have been studied as well as the characteristics that could be related to pollutant generation. The study considers the following issues: the types and level of criteria pollutant precursor compounds such as sulfur and nitrogen in coal, the influence of particle size and porosity in the generation of pollutant species, the participation of pollutant species in the combustion process, and basic properties such as heat capacity, and heat effects related to the conversion of coal during heating test. Coal from Antioquia, Valle del Cauca and Cundinamarca Regions were used. These coals are used domestically by the industrial and power sector. Particle sizes of 4, 2.5 and 1 cm were used from each one of these coals. The combustion tests were done in a fixed bed pilot furnace. The amount of air used was controlled during the experiment. In addition, air and gas flow, concentration and temperatures were registered. This paper presents a description of: characteristics of each test, composition of generated gases, and the influence of the particle size and coal origin in the pollutant emissions, also includes the results of test done in different samples took along each test.

  9. Combustion and gasification characteristics of pulverized coal using high-temperature air

    SciTech Connect

    Hanaoka, R.; Nakamura, M.; Kiga, T.; Kosaka, H.; Iwahashi, T.; Yoshikawa, K.; Sakai, M.; Muramatsu, K.; Mochida, S.

    1998-07-01

    In order to confirm performance of high-temperature-air combusting of pulverized coal, laboratory-scale combustion and gasification tests of coal were conducted changing air temperature and oxygen concentration in the air. Theses were conducted in a drop tube furnace of 200mm in inside diameter and 2,000mm in length. The furnace was heated by ceramic heater up to 1,300 C. A high-temperature air preheater utilizing the HRS (High Cycle Regenerative Combustion System) was used to obtain high-temperature combustion air. As the results, NOx emission was reduced when pulverized coal was fired with high-temperature-air. On the other hand, by lower oxygen concentration in combustion air diluted by nitrogen, NOx emission slightly decreased while became higher under staging condition.

  10. An Integrated Model of Coal/Coke Combustion in a Blast Furnace

    NASA Astrophysics Data System (ADS)

    Shen, Y. S.; Guo, B. Y.; Yu, A. B.; Austin, P.; Zulli, P.

    2010-03-01

    A three-dimensional integrated mathematical model of the combustion of pulverized coal and coke is developed. The model is applied to the region of lance-blowpipe-tuyere-raceway-coke bed to simulate the operation of pulverized coal injection in an ironmaking blast furnace. The model integrates two parts: pulverized coal combustion model in the blowpipe-tuyere-raceway-coke bed and the coke combustion model in the coke bed. The model is validated against the measurements in terms of coal burnout and gas composition, respectively. The comprehensive in-furnace phenomena are simulated in the raceway and coke bed, in terms of flow, temperature, gas composition, and coal burning characteristics. In addition, underlying mechanisms for the in-furnace phenomena are analyzed. The model provides a cost-effective tool for understanding and optimizing the in-furnace flow-thermo-chemical characteristics of the PCI process in full-scale blast furnaces.

  11. Combustion characteristics of blends of lignite and bituminous coal with different binder materials

    SciTech Connect

    Haykiri-Acma, H.; Ersoy-Mericboyu, A.; Kuecuekbayrak, S.

    2000-05-01

    In this study, the combustion characteristics of blends of a Turkish lignite and a Siberian bituminous coal with and without binder materials were investigated. Sunflower shell, sawdust, and molasses were used as binder materials. The combustion curves of the coal and binder material samples and of the blends were obtained using differential thermal analysis (DTA). The differences observed in the DTA curves of the samples are discussed in detail.

  12. Coal slurry solids/coal fluidized bed combustion by-product mixtures as plant growth media

    USGS Publications Warehouse

    Darmody, R.G.; Green, W.P.; Dreher, G.B.

    1998-01-01

    Fine-textured, pyritic waste produced by coal cleaning is stored in slurry settling ponds that eventually require reclamation. Conventionally, reclamation involves covering the dewatered coal slurry solids (CSS) with 1.3 m of soil to allow plant growth and prevent acid generation by pyrite oxidation. This study was conducted to determine the feasiblity of a less costly reclamation approach that would eliminate the soil cover and allow direct seeding of plants into amended CSS materials. Potential acidity of the CSS would be neutralized by additions of fluidized-bed combustion by-product (FBCB), an alkaline by-product of coal combustion. The experiment involved two sources of CSS and FBCB materials from Illinois. Birdsfoot trefoil (Lotus corniculatus L.), tall fescue (Festuca arundinacea Schreb.), and sweet clover (Melilotus officinalis (L.) Lam.) were seeded in the greenhouse into pots containing mixtures of the materials. CSS-1 had a high CaCO3:FeS2 ratio and needed no FBCB added to compensate for its potential acidity. CSS-2 was mixed with the FBCB materials to neutralize potential acidity (labeled Mix A and B). Initial pH was 5.6, 8.8, and 9.2 for the CSS-1, Mix A, and Mix B materials, respectively. At the end of the 70-day experiment, pH was 5.9 for all mixtures. Tall fescue and sweet clover grew well in all the treatments, but birdsfoot trefoil had poor emergence and survival. Elevated tissue levels of B, Cd, and Se were found in some plants. Salinity, low moisture holding capacity, and potentially phytotoxic B may limit the efficacy of this reclamation method.

  13. Energy recycling by co-combustion of coal and recovered paint solids from automobile paint operations

    SciTech Connect

    Achariya Suriyawong; Rogan Magee; Ken Peebles; Pratim Biswas

    2009-05-15

    This paper presents the results of an experimental study of particulate emission and the fate of 13 trace elements (arsenic (As), barium (Ba), cadmium (Cd), chromium (Cr), copper (Cu), cobalt (Co), manganese (Mn), molybdenum (Mo), nickel (Ni), lead (Pb), mercury (Hg), vanadium (V), and zinc (Zn)) during combustion tests of recovered paint solids (RPS) and coal. The emissions from combustions of coal or RPS alone were compared with those of co-combustion of RPS with subbituminous coal. The distribution/partitioning of these toxic elements between a coarse-mode ash (particle diameter (d{sub p}) > 0.5 {mu}m), a submicrometer-mode ash (d{sub p} < 0.5 {mu}m), and flue gases was also evaluated. Submicrometer particles generated by combustion of RPS alone were lower in concentration and smaller in size than that from combustion of coal. However, co-combustion of RPS and coal increased the formation of submicrometer-sized particles because of the higher reducing environment in the vicinity of burning particles and the higher volatile chlorine species. Hg was completely volatilized in all cases; however, the fraction in the oxidized state increased with co-combustion. Most trace elements, except Zn, were retained in ash during combustion of RPS alone. Mo was mostly retained in all samples. The behavior of elements, except Mn and Mo, varied depending on the fuel samples. As, Ba, Cr, Co, Cu, and Pb were vaporized to a greater extent from cocombustion of RPS and coal than from combustion of either fuel. Evidence of the enrichment of certain toxic elements in submicrometer particles has also been observed for As, Cd, Cr, Cu, and Ni during co-combustion. 27 refs., 6 figs., 5 tabs.

  14. Combustion characterization of beneficiated coal-based fuels. Quarterly report No. 12, January--March 1992

    SciTech Connect

    Chow, O.K.; Nsakala, N.Y.

    1992-08-01

    The Pittsburgh Energy Technology Center of the US Department of Energy has contracted with Combustion Engineering, Inc. (CE) to perform a five-year project on ``Combustion Characterization of Beneficiated Coal-Based Fuels.`` The beneficiated coals are produced by other contractors under the DOE Coal Preparation Program. Several contractor-developed advanced coal cleaning processes are run at pilot-scale cleaning facilities to produce 20-ton batches of fuels for shipment to CE`s laboratory in Windsor, Connecticut. CE then processes the products into either a coal-water fuel (CWF) or a dry microfine pulverized coa1 (DMPC) form for combustion testing. The objectives of this project include: (1) the development of an engineering data base which will provide detailed information on the properties of BCFs influencing combustion, ash deposition, ash erosion, particulate collection, and emissions; and (2) the application of this technical data base to predict the performance and economic impacts of firing the BCFs in various commercial boiler designs. The technical approach used to develop the technical data includes: bench-scale fuel property, combustion, and ash deposition tests; pilot-scale combustion and ash effects tests; and full-scale combustion tests. During the third quarter of 1992, the following technical progress was made: Continued analyses of drop tube furnace samples to determine devolatilization kinetics; completed editing of the fifth quarterly report and sent it to the publishing office; and prepared two technical papers for conferences.

  15. Combustion characterization of beneficiated coal-based fuels. Quarterly report No. 14, July--September 1992

    SciTech Connect

    Chow, O.K.; Nsakala, N.Y.

    1993-02-01

    The Pittsburgh Energy Technology Center of the US Department of Energy has contracted with Combustion Engineering, Inc. (CE) to perform a five-year project on ``Combustion Characterization of Beneficiated Coal-Based Fuels.`` The beneficiated coals are produced by other contractors under the DOE Coal Preparation Program. Several contractor-developed advanced coal cleaning processes are run at pilot-scale cleaning facilities to produce 20-ton batches of fuels for shipment to CE`s laboratory in Windsor, Connecticut. CE then processes the products into either a coal-water fuel (CWF) or a dry microfine pulverized coa1 (DMPC) form for combustion testing. The objectives of this project include: (1) the development of an engineering data base which will provide detailed information on the properties of BCFs influencing combustion, ash deposition, ash erosion, particulate collection, and emissions; and (2) the application of this technical data base to predict the performance and economic impacts of firing the BCFs in various commercial boiler designs. The technical approach used to develop the technical data includes: bench-scale fuel property, combustion, and ash deposition tests; pilot-scale combustion and ash effects tests; and full-scale combustion tests. During the third quarter of 1992, the following technical progress was made: Continued analyses of drop tube furnace samples to determine devolatilization kinetics; published two technical papers at conferences; and prepared for upcoming tests of new BCFs being produced.

  16. Combustion and gasification characteristics of chars from four commercially significant coals of different rank. Final report

    SciTech Connect

    Nsakala, N.Y.; Patel, R.L.; Lao, T.C.

    1982-09-01

    The combustion and gasification kinetics of four size graded coal chars were investigated experimentally in Combustion Engineering's Drop Tube Furnace System (DTFS). The chars were prepared in the DTFS from commercially significant coals representing a wide range of rank; these included a Pittsburgh No. 8 Seam hvAb coal, an Illinois No. 6 Seam hvCb coal, a Wyoming Sub C, and a Texas Lignite A. Additionally, a number of standard ASTM and special bench scale tests were performed on the coals and chars to characterize their physicochemical properties. Results showed that the lower rank coal chars were more reactive than the higher rank coal chars and that combustion reactions of chars were much faster than the corresponding gasification reactions. Fuel properties, temperature, and reactant gas partial pressure had a significant influence on both combustion and gasification, and particle size had a mild but discernible influence on gasification. Fuel reactivities were closely related to pore structure. Computer simulation of the combustion and gasification performances of the subject samples in the DTFS supported the experimental findings.

  17. Properties of adsorbents prepared by the alkali activation of Aleksandriisk brown coal

    SciTech Connect

    Yu.V. Tamarkina; V.G. Kolobrodov; T.G. Shendrik; V.A. Kucherenko

    2009-07-01

    Highly microporous adsorbents (micropore fraction of about 70%) were prepared by the alkali activation-thermolysis (800{sup o}C, 1 h) of brown coal (C{sup daf} = 70.4%) in the presence of potassium hydroxide at the KOH/coal weight ratio R{sub KOH} {le} 2.0 g/g. The dependences of the specific surface areas and adsorption capacities of the adsorbents for methylene blue (A{sub MB}, mg/g), iodine (A{sub I}, mg/g), and hydrogen (A{sub H{sub 2}} wt %) on R{sub KOH} were determined. The adsorbents obtained at R{sub KOH}{ge} 1.0 g/g exhibited developed specific surface areas and good adsorption characteristics (A{sub I} = 1000-1200 mg/g, A{sub MB} = 200-250 mg/g, and A{sub H{sub 2}} {le} 3.16 wt % at 0.33 MPa). The high capacity for hydrogen allowed us to consider brown coal adsorbents as promising materials for use as hydrogen accumulators.

  18. Gaseous products of the thermolysis of brown coal impregnated with potassium hydroxide

    SciTech Connect

    L.A. Bovan; V.A. Tamko; Y.V. Tamarkina; V.A. Kucherenko

    2009-07-01

    The yields of gaseous products (H{sub 2}, CO, CO{sub 2}, and C{sub n}H{sub 2n + 2} at n = 1-4) from brown coal and brown coal-KOH compounds were determined under conditions of nonisothermal heating (4{sup o}C/min) to 800{sup o}C followed by an isothermal exposure (1 h, 800{sup o}C). It was found that, in the presence of the alkali, the yields of H{sub 2}, CO, C{sub 2}H{sub 6}, and C{sub 3}H{sub 8} increased; the yields of CO{sub 2} and CH{sub 4} decreased; and the formation of isobutane was completely suppressed. Changes in the gas compositions were explained by the alkali degradation of C-C bonds in the organic matter of coal and by the thermally initiated dehydrogenation and dealkylation reactions of arene and alkane structural fragments, in which KOH molecules served as H-atom donors in the formation of H{sub 2} and alkanes.

  19. VARIATION OF ELEMENT SPECIATION IN COAL COMBUSTION AEROSOLS WITH PARTICLE SIZE

    EPA Science Inventory

    The speciation of sulfur, iron and key trace elements (Cr, As, Se, Zn) in combustion ash aerosols has been examined as a function of size from experimental combustion units burning Utah and Illinois bituminous coals. Although predominantly present as sulfate, sulfur was also pre...

  20. Effects of calcium magnesium acetate on the combustion of coal-water slurries

    SciTech Connect

    Levendis, Y.A.

    1991-01-01

    The general objective of the project is to investigate the combustion behavior of single and multiple Coal-Water Fuel (CWF) particles burning at high temperature environments. Both uncatalyzed as well as catalyzed CWF drops with Calcium Magnesium Acetate (CMA) catalyst will be studies. Emphasis will also be given in the effects of CMA on the sulfur capture during combustion.

  1. Effects of calcium magnesium acetate on the combustion of Coal-Water Slurries

    SciTech Connect

    Not Available

    1990-01-01

    The general objective of the project is to investigate the combustion behavior of single Coal-Water Slurry particles burning at high temperature environments. Both uncatalyzed as well catalyzed CWS drops with Calcium Magnesium Acetate (CMA) catalyst will be investigated. Emphasis will also be given in the effects of CMA on the sulfur capture during combustion.

  2. 75 FR 64974 - Notice of Data Availability on Coal Combustion Residual Surface Impoundments

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-10-21

    ... data posted in the docket for EPA's proposed rulemaking (75 FR 51434, August 20, 2010) on the Disposal... Coal Combustion Residual Surface Impoundments AGENCY: Environmental Protection Agency (EPA). ACTION... combustion residual surface impoundments as well as reports and materials related to the site assessments...

  3. Relationships between composition and pulmonary toxicity of prototype particles from coal combustion and pyrolysis

    EPA Science Inventory

    The hypothesis that health effects associated with coal combustion fly-ash particles are exacerbated by the simultaneous presence of iron and soot was tested through two sets of experiments. The first set created prototype particles from complete and partial combustion, or oxygen...

  4. RELATIONSHIPS BETWEEN COMPOSITION AND PULMONARY TOXICITY OF PROTOTYPE PARTICLES FROM COAL COMBUSTION AND PYROLYSIS (MONTREAL, CANADA)

    EPA Science Inventory

    The hypothesis that health effects associated with coal combustion fly-ash particles are exacerbated by the simultaneous presence of iron and soot was tested through two sets of experiments. The first set created prototype particles from complete and partial combustion, or oxygen...

  5. Investigation of the behavior of mercury compounds in coal combustion products

    SciTech Connect

    G.Ya. Gerasimov

    2005-07-15

    The main mechanisms of transformation of mercury compounds in coal combustion products in the region of high temperatures have been analyzed. A kinetic model of the process of gas-phase oxidation of metal mercury vapors is proposed. The features of the behavior of the investigated compounds in systems of cleaning combustion products from harmful impurities have been considered.

  6. Characterization of Coal Combustion Residues from Electric Utilities--Leaching and Characterization Data

    EPA Science Inventory

    This report evaluates changes in composition and constituent release by leaching that may occur to fly ash and other coal combustion residues (CCRs) in response to changes in air pollution control technology at coal-fired power plants. The addition of flue-gas desulfurization (FG...

  7. Characterization of Coal Combustion Residues from Electric Utilities Using Wet Scrubbers for Multi-Pollutant Control

    EPA Science Inventory

    This report evaluates changes that may occur to coal combustion residues (CCRs) in response to changes in air pollution control technology at coal-fired power plants, which will reduce emissions from the flue gas stack by transferring pollutants to fly ash and other air pollution...

  8. ENVIRONMENTAL EFFECTS OF WESTERN COAL COMBUSTION. PART III. THE WATER QUALITY OF ROSEBUD CREEK, MONTANA

    EPA Science Inventory

    The results of a study on Rosebud Creek, Montana, designed to assess the impacts on water quality of surface coal mining and/or coal combustion at Colstrip are summarized herein. A general degradation of water quality has been observed along the stream course but direct impacts o...

  9. Digital image processing applications in the ignition and combustion of char/coal particles

    SciTech Connect

    Annamalai, K.; Kharbat, E.; Goplakrishnan, C.

    1992-12-01

    Digital image processing, is employed in this remarch study in order to visually investigate the ignition and combustion characteristics of isolated char/coal particles as well as the effect of interactivecombustion in two-particle char/coal arrays. Preliminary experiments are conducted on miniature isolated candles as well as two-candle arrays.

  10. ASSESSING SPECIATION AND RELEASE OF HEAVY METALS FROM COAL COMBUSTION PRODUCTS

    EPA Science Inventory

    In this study, the speciation of heavy metals such as arsenic, selenium, lead, zinc and mercury in coal combustion products (CCPs) was evaluated using sequential extraction procedures. Coal fly ash, bottom ash and flue gas desulphurization (FGD) sludge samples were used in the ex...

  11. CONTROL OF CRITERIA AND NON-CRITERIA POLLUTANTS FROM COAL/OIL MIXTURE COMBUSTION

    EPA Science Inventory

    The report summarizes the existing data base on NOx, SO2, and particulate emissions from combustion sources burning coal/oil mixtures (COMs). The need for the U.S. to reduce its dependence on oil and expand its use of coal has prompted a number of industrial and utility energy pr...

  12. Understanding the behavior of Australian black coals in pressurized fluidized bed combustion

    SciTech Connect

    Stubington, J.F.; Wang, A.L.T.; Cui, Y.

    1999-07-01

    Ultimately, this study aims to predict the coal combustion efficiency in an industrial pressurized fluidized bed combustor (PFBC) for Australian black coals. This combustion efficiency depends predominantly upon the rate of elutriation of fine carbon particles, which is proportional to bed carbon loading in atmospheric experiments. The bed carbon loading is, in turn, dependent upon the rate of combustion of char particles within the PFBC. A novel batch-fed reactor has been designed, constructed and commissioned to enable separation and study of the mechanisms of coal devolatilization, char combustion and fine carbon particle elutriation in a PFBC and extraction of coal-specific parameters to describe these processes. The attrition and char combustion rates can only be determined experimentally and it is essential to match the environment around each coal particle, so that the results may be translated to the industrial scale. Therefore, the rig was designed for identical conditions of pressure, temperature, particle size and fluidizing velocity within the bed to those used industrially. The exhaust gas is analyzed continuously for oxygen, carbon dioxide, carbon monoxide and hydrocarbons as a function of time after coal injection, allowing separation and identification of the devolatilization and char combustion stages as well as measurement of the combustion rates. The elutriated carbon particles undergo minimal freeboard combustion and are collected in a cyclone and an in-line filter over any period of time during the experiment, for subsequent analysis. The sand bed containing the rig for collection and characterization of the partially burnt char particles. The rig is mostly computer-controlled and the design was subjected to a hazards analysis before construction. Results from the rig will be used in a mathematical model to predict the performance of the coals in industrial-scale PFBC.

  13. NOx EMISSIONS PRODUCED WITH COMBUSTION OF POWDER RIVER BASIN COAL IN A UTILITY BOILER

    SciTech Connect

    John S. Nordin; Norman W. Merriam

    1997-04-01

    The objective of this report is to estimate the NOx emissions produced when Powder River Basin (PRB) coal is combusted in a utility boiler. The Clean Air Act regulations specify NOx limits of 0.45 lb/mm Btu (Phase I) and 0.40 lb/mm Btu (Phase II) for tangentially fired boilers, and 0.50 lb/mm 13tu (Phase II) and 0.46 lb/mm Btu (Phase II) for dry-bottom wall-fired boilers. The Clean Air Act regulations also specify other limits for other boiler types. Compliance for Phase I has been in effect since January 1, 1996. Compliance for Phase II goes into effect on January 1, 2000. Emission limits are expressed as equivalent NO{sub 2} even though NO (and sometimes N{sub 2}O) is the NOx species emitted during combustion. Regulatory agencies usually set even lower NOx emission limits in ozone nonattainment areas. In preparing this report, Western Research Institute (WRI) used published test results from utilities burning various coals, including PRB coal, using state-of-the art control technology for minimizing NOx emissions. Many utilities can meet Clean Air Act NOx emission limits using a combination of tight combustion control and low-NOx burners and by keeping furnaces clean (i.e., no slag buildup). In meeting these limits, some utilities also report problems such as increased carbon in their fly ash and excessive furnace tube corrosion. This report discusses utility experience. The theory of NOx emission formation during coal combustion as related to coal structure and how the coal is combusted is also discussed. From this understanding, projections are made for NOx emissions when processed PRB coal is combusted in a test similar to that done with other coals. As will be shown, there are a lot of conditions for achieving low NOx emissions, such as tight combustion control and frequent waterlancing of the furnace to avoid buildup of deposits.

  14. Phytostabilization of a landfill containing coal combustion waste.

    SciTech Connect

    Barton, Christopher; Marx, Donald; Adriano, Domy; Koo, Bon Jun; Newman, Lee; Czapka, Stephen; Blake, John

    2005-12-01

    The establishment of a vegetative cover to enhance evapotranspiration and control runoff and drainage was examined as a method for stabilizing a landfill containing coal combustion waste. Suitable plant species and pretreatment techniques in the form of amendments, tilling, and chemical stabilization were evaluated. A randomized plot design consisting of three subsurface treatments (blocks) and five surface amendments (treatments) was implemented. The three blocks included (1) ripping and compost amended, (2) ripping only, and (3) control. Surface treatments included (1) topsoil, (2) fly ash, (3) compost, (4) apatite, and (5) control. Inoculated loblolly (Pinus taeda) and Virginia (Pinus virginiana) pine trees were planted on each plot. After three growing seasons, certain treatments were shown to be favorable for the establishment of vegetation on the basin. Seedlings located on block A developed a rooting system that penetrated into the basin media without significant adverse effects to the plant. However, seedlings on blocks B and C displayed poor rooting conditions and high mortality, regardless of surface treatment. Pore-water samples from lysimeters in block C were characterized by high acidity, Fe, Mn, Al, sulfate, and traceelement concentrations. Water-quality characteristics of the topsoil plots in block A, however, conformed to regulatory protocols. A decrease in soil-moisture content was observed in the rooting zone of plots that were successfully revegetated, which suggests that the trees, in combination with the surface treatments, influenced the water balance by facilitating water loss through transpiration and thereby reducing the likelihood of unwanted surface runoff and/or drainage effluent.

  15. Coal Cleaning Using Resonance Disintegration for Mercury and Sulfur Reduction Prior to Combustion

    SciTech Connect

    Andrew Lucero

    2005-04-01

    Coal-cleaning processes have been utilized to increase the heating value of coal by extracting ash-forming minerals in the coal. These processes involve the crushing or grinding of raw coal followed by physical separation processes, taking advantage of the density difference between carbonaceous particles and mineral particles. In addition to the desired increase in the heating value of coal, a significant reduction of the sulfur content of the coal fed to a combustion unit is effected by the removal of pyrite and other sulfides found in the mineral matter. WRI is assisting PulseWave to develop an alternate, more efficient method of liberating and separating the undesirable mineral matter from the carbonaceous matter in coal. The approach is based on PulseWave's patented resonance disintegration technology that reduces that particle size of materials by application of destructive resonance, shock waves, and vortex generating forces. Illinois No.5 coal, a Wyodak coal, and a Pittsburgh No.8 coal were processed using the resonance disintegration apparatus then subjected to conventional density separations. Initial microscopic results indicate that up to 90% of the pyrite could be liberated from the coal in the machine, but limitations in the density separations reduced overall effectiveness of contaminant removal. Approximately 30-80% of the pyritic sulfur and 30-50% of the mercury was removed from the coal. The three coals (both with and without the pyritic phase separated out) were tested in WRI's 250,000 Btu/hr Combustion Test Facility, designed to replicate a coal-fired utility boiler. The flue gases were characterized for elemental, particle bound, and total mercury in addition to sulfur. The results indicated that pre-combustion cleaning could reduce a large fraction of the mercury emissions.

  16. STUDIES OF THE SPONTANEOUS COMBUSTION OF LOW RANK COALS AND LIGNITES

    SciTech Connect

    Joseph M. Okoh; Joseph N.D. Dodoo

    2005-07-26

    Spontaneous combustion has always been a problem in coal utilization especially in the storage and transportation of coal. In the United States, approximately 11% of underground coal mine fires are attributed to spontaneous coal combustion. The incidence of such fires is expected to increase with increased consumption of lower rank coals. The cause is usually suspected to be the reabsorption of moisture and oxidation. To understand the mechanisms of spontaneous combustion this study was conducted to (1) define the initial and final products during the low temperature (10 to 60 C) oxidation of coal at different partial pressures of O{sub 2}, (2) determine the rate of oxidation, and (3) measure the reaction enthalpy. The reaction rate (R) and propensity towards spontaneous combustion were evaluated in terms of the initial rate method for the mass gained due to adsorbed O{sub 2}. Equipment that was used consisted of a FT-IR (Fourier Transform-Infrared Spectrometer, Perkin Elmer), an accelerated surface area porosimeter (ASAP, Micromeritics model 2010), thermogravimetric analyzer (TGA, Cahn Microbalance TG 121) and a differential scanning calorimeter (DSC, Q1000, thermal analysis instruments). Their combination yielded data that established a relation between adsorption of oxygen and reaction enthalpy. The head space/ gas chromatograph/ mass spectrometer system (HS/GC/MS) was used to identify volatiles evolved during oxidation. The coal samples used were Beulah lignite and Wyodak (sub-bituminous). Oxygen (O{sub 2}) absorption rates ranged from 0.202 mg O{sub 2}/mg coal hr for coal sample No.20 (Beulah pyrolyzed at 300 C) to 6.05 mg O{sub 2}/mg coal hr for coal sample No.8 (wyodak aged and pyrolyzed at 300 C). Aging of coal followed by pyrolysis was observed to contribute to higher reaction rates. Reaction enthalpies ranged from 0.42 to 1580 kcal/gm/mol O{sub 2}.

  17. DEVELOPMENT OF ACTIVATED CARBONS FROM COAL COMBUSTION BY-PRODUCTS

    SciTech Connect

    Harold H. Schobert; M. Mercedes Maroto-Valer; Zhe Lu

    2003-09-30

    The increasing role of coal as a source of energy in the 21st century will demand environmental and cost-effective strategies for the use of coal combustion by-products (CCBPs), mainly unburned carbon in fly ash. Unburned carbon is nowadays regarded as a waste product and its fate is mainly disposal, due to the present lack of efficient routes for its utilization. However, unburned carbon is a potential precursor for the production of adsorbent carbons, since it has gone through a devolatilization process while in the combustor, and therefore, only requires to be activated. Accordingly, the principal objective of this work was to characterize and utilize the unburned carbon in fly ash for the production of activated carbons. The unburned carbon samples were collected from different combustion systems, including pulverized utility boilers, a utility cyclone, a stoker, and a fluidized bed combustor. LOI (loss-on-ignition), proximate, ultimate, and petrographic analyses were conducted, and the surface areas of the samples were characterized by N2 adsorption isotherms at 77K. The LOIs of the unburned carbon samples varied between 21.79-84.52%. The proximate analyses showed that all the samples had very low moisture contents (0.17 to 3.39 wt %), while the volatile matter contents varied between 0.45 to 24.82 wt%. The elemental analyses show that all the unburned carbon samples consist mainly of carbon with very little hydrogen, nitrogen, sulfur and oxygen In addition, the potential use of unburned carbon as precursor for activated carbon (AC) was investigated. Activated carbons with specific surface area up to 1075m{sup 2}/g were produced from the unburned carbon. The porosity of the resultant activated carbons was related to the properties of the unburned carbon feedstock and the activation conditions used. It was found that not all the unburned carbon samples are equally suited for activation, and furthermore, their potential as activated carbons precursors could be

  18. EFFECTS OF COMBUSTION PARAMETERS ON POLYCHLORINATED DIBENZODIOXIN AND DIBENZOFURAN HOMOLOGUE PROFILES FROM MUNICIPAL WASTE AND COAL CO-COMBUSTION

    EPA Science Inventory

    Variation in polychlorinated dibenzo-p-dioxin and polychlorinated dibenzofuran (PCDD and PCDF) homologue profiles from a pilot scale (0.6 MWt, 2x106 Btu/hr), co-fired-fuel [densified refuse derived fuel (dRDF) and high-sulfur Illinois coal] combustion system was used to provide i...

  19. Advanced coal-fueled gas turbine systems: Subscale combustion testing. Topical report, Task 3.1

    SciTech Connect

    Not Available

    1993-05-01

    This is the final report on the Subscale Combustor Testing performed at Textron Defense Systems` (TDS) Haverhill Combustion Laboratories for the Advanced Coal-Fueled Gas Turbine System Program of the Westinghouse Electric Corp. This program was initiated by the Department of Energy in 1986 as an R&D effort to establish the technology base for the commercial application of direct coal-fired gas turbines. The combustion system under consideration incorporates a modular staged, rich-lean-quench, Toroidal Vortex Slogging Combustor (TVC) concept. Fuel-rich conditions in the first stage inhibit NO{sub x} formation from fuel-bound nitrogen; molten coal ash and sulfated sorbent are removed, tapped and quenched from the combustion gases by inertial separation in the second stage. Final oxidation of the fuel-rich gases, and dilution to achieve the desired turbine inlet conditions are accomplished in the third stage, which is maintained sufficiently lean so that here, too, NO{sub x} formation is inhibited. The primary objective of this work was to verify the feasibility of a direct coal-fueled combustion system for combustion turbine applications. This has been accomplished by the design, fabrication, testing and operation of a subscale development-type coal-fired combustor. Because this was a complete departure from present-day turbine combustors and fuels, it was considered necessary to make a thorough evaluation of this design, and its operation in subscale, before applying it in commercial combustion turbine power systems.

  20. Application of Foam-gel Technique to Control CO Exposure Generated During Spontaneous Combustion of Coal in Coal Mines.

    PubMed

    Ren, Xing W; Wang, Feng Z; Guo, Qing; Zuo, Zhao B; Fang, Qi S

    2015-01-01

    In China, 47.3% of state-owned coal mines are located in coal seams that are prone to spontaneous combustion. The spontaneous combustion of coal is the main cause of the generation of a large amount of carbon monoxide, which can cause serious health issues to miners. A new technique using foam-gel formation was developed to effectively control the spontaneous combustion of coal. The gel can capture more than 90% of the water in the grout and at the same time the foam can cover dangerous areas in the goaf by stacking and cooling of foam in all directions. In this study, a mechanism of foam-gel formation was introduced and the optimal proportions of additives were defined based on experiments of different foaming properties, gelling time and water loss rate as the main index parameters. The results of a field application in a coal mine promise that this new technique would effectively prevent coal oxidation in the goaf and reduce the generation of carbon monoxide. PMID:26259722

  1. Analysis of Coals with Different Spontaneous Combustion Characteristics Using Infrared Spectrometry

    NASA Astrophysics Data System (ADS)

    Tang, Y.

    2015-05-01

    The relationship between the spontaneous combustion characteristics and the functional group distributions of coal was studied by analyzing different samples of coals using infrared spectroscopy. The analysis demonstrated that coal with a higher content of oxygen-containing functional groups and aliphatic hydrocarbons is more likely to spontaneously combust. Compared with coal which showed little spontaneous combustion tendency, coal, which is prone to spontaneous combustion, presented stretching bands of aromatic C=C at 1.604 cm-1, -CH2 at ~2857-2851 and 1443 cm-1, and C-O at 1030 cm-1 with the absorption peaks at those stretching bands showing the greatest difference. After being oxidized at low temperature, the aliphatic hydrocarbons and oxygen-containing functional groups changed significantly, while the absorption peak intensity of aromatic rings exhibited only slight changes. The results verified that diffuse reflectance Fourier transform infrared spectroscopy is an efficient method for investigating the spontaneous combustion characteristics and the variation of the active groups in the oxidation of coal at low temperature.

  2. Assessment of the effect of high ash content in pulverized coal combustion

    SciTech Connect

    Jayanti, S.; Maheswaran, K.; Saravanan, V.

    2007-05-15

    The existing literature on CFD-based coal combustion modelling is applicable mainly for coals of low ash content and the calculations are done on an ash-free basis. In Indian coals, the ash content may be significantly higher, up to 40% or more. Studies reported in the literature show that the mineral matter in the coal may have a number of effects on the combustion characteristics. In the present study, a sensitivity analysis is performed, using the CFD code CFX of AEA Technology, on the likely effect of ash content on the char reactivity, oxygen diffusion rate for char combustion and on the radiative heat transfer parameters. The results show that the effect of enhanced char reactivity is negligible whereas reduced oxygen diffusion rates due to a thicker ash layer may result in a significant reduction in char oxidation rates with a resultant decrease in the peak temperature in the furnace. The global parameters such as the peak temperature and the flue gas temperature remain relatively insensitive to the presence of high ash content. These results are consistent with the experimental observations of Kurose et al. . Kurose, M. Ikeda, H. Makino, Combustion characteristics of high ash coal in pulverized coal combustion, J. Fuel 80 (2001) 1447-1455).

  3. Environmentally sound thermal energy extraction from coal and wastes using high temperature air combustion technology

    SciTech Connect

    Yoshikawa, Kunio

    1999-07-01

    High temperature air combustion is one of promising ways of burning relatively low BTU gas obtained from gasification of low grade coal or wastes. In this report, the author proposes a new power generation system coupled with high temperature air gasification of coal/wastes and high temperature air combustion of the syngas from coal/wastes. This system is realized by employing Multi-staged Enthalpy Extraction Technology (MEET). The basic idea of the MEET system is that coal or wastes are gasified with high temperature air of about 1,000 C, then the generated syngas is cooled in a heat recovery boiler to be cleaned-up in a gas cleanup system (desulfurization, desalinization and dust removal). Part of thermal energy contained in this cleaned-up syngas is used for high temperature air preheating, and the complete combustion of the fuel gas is done using also high temperature air for driving gas turbines or steam generation in a boiler.

  4. Fiber optic sensing system for temperature and gas monitoring in coal waste pile combustion environments

    NASA Astrophysics Data System (ADS)

    Viveiros, D.; Ribeiro, J.; Ferreira, J.; Lopez-Albada, A.; Pinto, A. M. R.; Perez-Herrera, R. A.; Diaz, S.; Lopez-Gil, A.; Dominguez-Lopez, A.; Esteban, O.; Martin-Lopez, S.; Auguste, J.-L.; Jamier, R.; Rougier, S.; Silva, S. O.; Frazão, O.; Santos, J. L.; Flores, D.; Roy, P.; Gonzalez-Herraez, M.; Lopez-Amo, M.; Baptista, J. M.

    2015-09-01

    It is presented an optical fiber sensing system projected to operate in the demanding conditions associated with coal waste piles in combustion. Distributed temperature measurement and spot gas sensing are requirements for such a system. A field prototype has been installed and is continuously gathering data, which will input a geological model of the coal waste piles in combustion aiming to understand their dynamics and evolution. Results are presented on distributed temperature and ammonia measurement, being noticed any significant methane emission in the short time period considered. Carbon dioxide is also a targeted gas for measurement, with validated results available soon. The assessment of this technology as an effective and reliable tool to address the problem of monitoring coal waste piles in combustion opens the possibility of its widespread application in view of the worldwide presence of coal related fires.

  5. Environmental effects of increased coal utilization: ecological effects of gaseous emissions from coal combustion.

    PubMed Central

    Glass, N R

    1979-01-01

    This report is limited to an evaluation of the ecological and environmental effects of gaseous emissions and aerosols of various types which result from coal combustion. It deals with NOx, SOx, fine particulate, photochemical oxidant and acid precipitation as these pollutants affect natural and managed resources and ecosystems. Also, synergistic effects involving two or more pollutants are evaluated as well as ecosystem level effects of gaseous pollutants. There is a brief summary of the effects on materials and atmospheric visibility of increased coal combustion. The economic implications of ecological effects are identified to the extent they can be determined within acceptable limits. Aquatic and terrestrial effects are distinguished where the pollutants in question are clearly problems in both media. At present, acid precipitation is most abundant in the north central and northeastern states. Total SOx and NOx emissions are projected to remain high in these regions while increasing relatively more in the western than in the eastern regions of the country. A variety of ecological processes are affected and altered by air pollution. Such processes include community succession and retrogression, nutrient biogeochemical cycling, photosynthetic activity, primary and secondary productivity, species diversity and community stability. Estimates of the non health-related cost of air pollutants range from several hundred million dollars to $1.7 billion dollars per year. In general, these estimates include only those relatively easily measured considerations such as the known losses to cultivate crops from acute air pollution episodes or the cost of frequent repainting required as a result of air pollution. No substantial nationwide estimates of losses to forest productivity, natural ecosystem productivity which is tapped by domestic grazing animals and wildlife, and other significant dollar losses are available. PMID:44247

  6. The physical and chemical characteristics of pulverized coal combustion ashes

    SciTech Connect

    Ozasa, Kazuo; Kamijo, Tsunao; Owada, Tetsuo; Hosoda, Nobumichi

    1999-07-01

    Japan is the world's largest consumer of coal. Most of it is imported from various countries around the world. While coal generates more CO{sub 2}, which contributes to the greenhouse effect more than other types of fuel, plans are being drawn up to depend more on coal energy in order to maintain diversity in energy sources. Production of coal ash will increase as a result. In Japan, therefore, the public and private sectors are active in both developing and implementing clean, efficient and effective coal utilization technologies. More than 100 types of coal are being burned in Japan at present. For example, a power generating plant burns 20 to 40 different types of coal annually. Since a single type or coal blended with several different types are burned in Japan, the properties of coal ash differ by consuming plant and season. Therefore, understanding coal ash characteristics based on various properties is essential to the effective utilization of coal. The center of Coal Utilization, Japan has researched and developed effective utilization of coal ash as a supplementary project of the Ministry of International Trade and Industry. Chemical, physical, soil, and leaching characteristics, which are fundamental to using pulverized coal ash as a civil engineering material in large quantities, were selected and are described in this report.

  7. Black and brown carbon fractal aggregates from combustion of two fuels widely used in Asian rituals

    NASA Astrophysics Data System (ADS)

    Chakrabarty, Rajan K.; Arnold, Ian J.; Francisco, Dianna M.; Hatchett, Benjamin; Hosseinpour, Farnaz; Loria, Marcela; Pokharel, Ashok; Woody, Brian M.

    2013-06-01

    Incense sticks and mustard oil are the two most popular combustion fuels during rituals and social ceremonies in Asian countries. Given their widespread use in both closed and open burning activities, it is important to quantify the spectral radiative properties of aerosols emitted from the combustion of both fuels. This information is needed by climate models to assess the impact of these aerosols on radiative forcing. In this study, we used a 3-wavelength integrated photoacoustic-nephelometer - operating simultaneously at 405, 532 and 781nm - to measure the optical coefficients of aerosols emitted from the laboratory combustion of mustard oil lamp and two types of incense sticks. From the measured optical coefficients at three wavelengths, time-varying single scattering albedo (SSA), absorption Ångström exponent (AAE), and scattering Ångström exponent (SAE) were calculated. For incense smoke particles, the time-averaged mean AAE values were found to be as high as 8.32 (between 405 and 532nm) and 6.48 (between 532 and 781nm). This spectrally-varying characteristic of AAE indicates that brown carbon - a class of organic carbon which strongly absorbs solar radiation in the blue and near ultraviolet - is the primary component of incense smoke aerosols. For aerosols emitted from the burning of mustard oil lamp, the time-averaged mean AAE values were ˜1.3 (between 405 and 781nm) indicating that black carbon (BC) is the primary constituent. Scanning electron microscopy combined with image processing revealed the morphology of incense smoke aerosols to be non-coalescing and weakly-bound aggregates with a mean two-dimensional (2-d) fractal dimension (Df)=1.9±0.07, while the mustard oil smoke aerosols had typical fractal-like BC aggregate morphology with a mean 2-d Df=1.85±0.09.

  8. Toxic substances from coal combustion -- A comprehensive assessment. Quarterly report, October 1, 1996--December 31, 1996

    SciTech Connect

    Bool, L.E. III; Senior, C.L.; Huggins, F.; Huffman, G.P.; Shah, N.

    1997-01-31

    The Clean Air Act Amendments of 1990 identify a number of hazardous air pollutants (HAPs) as candidates for regulation. Should regulations be imposed on HAP emissions from coal-fired power plants, a sound understanding of the fundamental principles controlling the formation and partitioning of toxic species during coal combustion will be needed. With support from the Federal Energy Technology Center (FETC), the Electric Power Research Institute, and VTT (Finland), Physical Sciences Inc. (PSI) has teamed with researchers from USGS, MIT, the University of Arizona (UA), the University of Kentucky (UKy), the University of Connecticut, and Princeton University to develop a broadly applicable emissions model useful to regulators and utility planners. The new Toxics Partitioning Engineering Model (ToPEM) will be applicable to all combustion conditions including new fuels and coal blends, low-NOx combustion systems, and new power generation plants. Development of ToPEM will be based on PSI`s existing Engineering Model for Ash Formation (EMAF). During the past quarter the final program coal, from the Wyodak seam in the Powder River Basin, was acquired and distributed. Extensive coal characterization and laboratory work is underway to develop and test new sub-models. Coal characterization in the past quarter included direct identification of the modes of occurrence of various trace inorganic species in coal and ash using unique analytical techniques such as XAFS analysis and selective leaching. Combustion testing of the bituminous coals continued and additional data were obtained on trace element vaporization in the combustion zone. Studies of post-combustion trace element transformations, such as mercury speciation in the flue gas, were also begun in the last quarter.

  9. Characterizing the Leaching Behavior of Coal Combustion Residues using the Leaching Environmental Assessment Framework (LEAF) to Inform Future Management Decisions

    EPA Science Inventory

    Abstract for presentation on Characterizing the Leaching Behavior of Coal Combustion Residues using the Leaching Environmental Assessment Framework (LEAF) to Inform Future Management Decisions. The abstract is attached.

  10. Air toxic emissions from the combustion of coal: Identifying and quantifying hazardous air pollutants from US coals

    SciTech Connect

    Szpunar, C.B.

    1992-09-01

    This report addresses the key air toxic emissions likely to emanate from continued and expanded use of domestic coal. It identifies and quantifies those trace elements specified in the US 1990 Clean Air Act Amendments, by tabulating selected characterization data on various source coals by region, state, and rank. On the basis of measurements by various researchers, this report also identifies those organic compounds likely to be derived from the coal combustion process (although their formation is highly dependent on specific boiler configurations and operating conditions).

  11. Combustion Engineering Integrated Coal Gasification Combined Cycle Repowering Project: Clean Coal Technology Program

    SciTech Connect

    Not Available

    1992-03-01

    On February 22, 1988, DOE issued Program Opportunity Notice (PON) Number-DE-PS01-88FE61530 for Round II of the CCT Program. The purpose of the PON was to solicit proposals to conduct cost-shared ICCT projects to demonstrate technologies that are capable of being commercialized in the 1990s, that are more cost-effective than current technologies, and that are capable of achieving significant reduction of SO[sub 2] and/or NO[sub x] emissions from existing coal burning facilities, particularly those that contribute to transboundary and interstate pollution. The Combustion Engineering (C-E) Integrated Coal Gasification Combined Cycle (IGCC) Repowering Project was one of 16 proposals selected by DOE for negotiation of cost-shared federal funding support from among the 55 proposals that were received in response to the PON. The ICCT Program has developed a three-level strategy for complying with the National Environmental Policy Act (NEPA) that is consistent with the President's Council on Environmental Quality regulations implementing NEPA (40 CFR 1500-1508) and the DOE guidelines for compliance with NEPA (10 CFR 1021). The strategy includes the consideration of programmatic and project-specific environmental impacts during and subsequent to the reject selection process.

  12. Short-term influence of coal mine reclamation using coal combustion residues on groundwater quality.

    PubMed

    Cheng, Chin-Min; Amaya, Maria; Butalia, Tarunjit; Baker, Robert; Walker, Harold W; Massey-Norton, John; Wolfe, William

    2016-11-15

    Two full-scale coal mine reclamation projects using coal combustion residues (CCRs) were recently carried out at highwall pit complexes near the Conesville and Cardinal coal-fired power plants owned by American Electric Power. The environment impacts of the reclamation projects were examined by regularly monitoring the leaching characteristics of the backfilling CCRs and the water quality of the uppermost aquifers underlying the sites. With over five years of field monitoring, it shows that the water quality at both demonstration sites had changed since the reclamation began. By analyzing the change of the hydrogeochemical properties, it was concluded that the water quality impact observed at the Conesville Five Points site was unlikely due to the seepage of FGD material leachates. Reclamation activities, such as logging, grading, and dewatering changed the hydrogeological conditions and resulted in the observed water quality changes. The same hydrogeological effect on water quality was also found at the Cardinal Star Ridge site during the early stage of the reclamation (approximately the first 22months). Subsequent measurements showed the water quality to be strongly influenced by the water in the reclaimed highwall pit. Despite the changes to the water quality, the impacts are insignificant and temporary. None of the constitutes showed concentration levels higher than the regulatory leaching limits set by the Ohio Department of Natural Resources' Division of Mineral Resources Management for utilizing CCRs in mined land reclamation. Compared to the local aquifers, the concentrations of eleven selected constituents remained at comparable levels throughout the study period. There are four constituents (i.e., As, Be, Sb, and Tl) that exceeded their respective MCLs after the reclamation began. These detections were found shortly (i.e., within 2years) after the reclamation began and decreased to the levels either lower than the respective detection limits or similar to

  13. Combustion and desulfurization of low-grade high-sulfur coal briquettes

    SciTech Connect

    Zhu, H.; Xi, D.; Xu, K.; He, D.

    1994-12-31

    A typical kind of coal with 40% ash and 4% sulfur is studied. It is hard to ignite when the coal is briquetted with the addition of calcium carbide waste at a reasonable Ca/S ratio. Combustion properties of sugar cane waste, coal and their blends are studied on TGA. The ignition temperature is reduced and the combustibility is improved with a small dosage of sugar cane waste. A rational ingredient for coal briquettes is determined, and then it is tested on a bench-scale fixed-bed unit under controlled atmosphere. Experimental results have proven that these coal briquettes can be ignited more easily. Sulfur fixation reaches 45% at Ca/S 1.3--1.8 under 1,250 C.

  14. Statistical modeling of spontaneous combustion in industrial-scale coal stockpiles

    SciTech Connect

    Ozdeniz, H

    2009-07-01

    Companies consuming large amounts of coal should work with coal stocks in order to not face problems due to production delays. The industrial-scale stockpiles formed for the aforementioned reasons cause environmental problems and economic losses for the companies. This study was performed in a coal stock area of a large company in Konya, which uses large amounts of coal in its manufacturing units. The coal stockpile with 5 m width, 10 m length, 3 m height, and having 120 tons of weight was formed in the coal stock area of the company. The inner temperature data of the stockpile was recorded by 17 temperature sensors placed inside the stockpile at certain points. Additionally, the data relating to the air temperature, air humidity, atmospheric pressure, wind velocity, and wind direction that are the parameters affecting the coal stockpile were also recorded. A statistical model applicable for a spontaneous combustion event was developed during this study after applying multi-regression analyses to the data recorded in the stockpile during the spontaneous combustion event. The correlation coefficients obtained by the developed statistical model were measured approximately at a 0.95 level. Thus, the prediction of temperature variations influential in the spontaneous combustion event of the industrial-scale coal stockpiles will be possible.

  15. Prevention of trace and major element leaching from coal combustion products by hydrothermally-treated coal ash

    SciTech Connect

    Adnadjevic, B.; Popovic, A.; Mikasinovic, B.

    2009-07-01

    The most important structural components of coal ash obtained by coal combustion in 'Nikola Tesla A' power plant located near Belgrade (Serbia) are amorphous alumosilicate, alpha-quartz, and mullite. The phase composition of coal ash can be altered to obtain zeolite type NaA that crystallizes in a narrow crystallization field (SiO{sub 2}/Al{sub 2}O{sub 3}; Na{sub 2}O/SiO{sub 2}; H{sub 2}O/Na{sub 2}O ratios). Basic properties (crystallization degree, chemical composition, the energy of activation) of obtained zeolites were established. Coal ash extracts treated with obtained ion-exchange material showed that zeolites obtained from coal ash were able to reduce the amounts of iron, chromium, nickel, zinc, copper, lead, and manganese in ash extracts, thus proving its potential in preventing pollution from dump effluent waters.

  16. Elution of Ti during solvent extraction of coal and the transformation of eluted Ti upon combustion

    SciTech Connect

    Zhang, L.A.; Takanohashi, T.; Saito, I.; Wang, Q.Y.; Ninomiya, Y.

    2008-06-15

    Solvent extraction of coal is an effective method for removing coal ash, thereby generating the ultraclean fuel that can be directly combusted in gas turbine. Due to their organic affinity, a few inorganic elements can be extracted as well. Ti in coal extract, its elution from raw coal as well as the transformation of eluted Ti during coal extract combustion, have been investigated. Two coals of the U.S. and their acid-washed samples were extracted under 1 MPa N{sub 2} (cold) at 360{sup o}C. The solvents used include nonpolar 1-methylnaphthalene and its mixtures with polar indole. The results indicate that, Ti in coal extracts is mainly composed of nanoparticles including TiO{sub 2} (anatase) and Ti associated with quartz. These particles are insoluble in any acids, having a fine dispersion into coal matrix. Upon coal fragmentation at 360{sup o}C, they could be liberated, and, hence, traversed the filter for isolating coal extracts. The organo-Ti was preferentially extracted as well, which is most likely in a form of Ti porphyrin or Ti chelated with phenol-oxygen. These findings also have implications for revealing the modes of occurrence of Ti in the raw coals. Combustion of coal extract at 1,000{sup o}C resulted in the formation of nanometric TiO{sub 2} polymorphs and complex compounds like FeZnTiO{sub 4}. The former species could be mainly formed by the phase change of TiO{sub 2} (anatase) at high-temperatures, while formation of the latter one could involve the capture of metallic vapors like Zn on TiO{sub 2} polymorphs.

  17. Natural attenuation of coal combustion waste in river sediments.

    PubMed

    Markwiese, James T; Rogers, William J; Carriker, Neil E; Thal, David I; Vitale, Rock J; Gruzalski, Jacob G; Rodgers, Erin E; Babyak, Carol M; Ryti, Randall T

    2014-08-01

    The weathering of coal combustion products (CCPs) in a lotic environment was assessed following the Tennessee Valley Authority (Kingston, TN) fly ash release of 2008 into surrounding rivers. Sampled materials included stockpiled ash and sediment collected from 180 to 880 days following the release. Total recoverable concentrations of heavy metals and metalloids in sediment were measured, and percent ash was estimated visually or quantified by particle counts. Arsenic and selenium in sediment were positively correlated with percent ash. For samples collected 180 days after the release, total concentrations of trace elements downstream of the release were greater than reference levels but less than concentrations measured in stockpiled ash. Total concentrations of trace elements remained elevated in ash-laden sediment after almost 2.5 years. A sequential extraction procedure (SEP) was used to speciate selected fractions of arsenic, copper, lead, nickel, and selenium in decreasing order of bioavailability. Concentrations of trace elements in sequentially extracted fractions were one to two orders of magnitude lower than total recoverable trace elements. The bulk of sequentially extractable trace elements was associated with iron-manganese oxides, the least bioavailable fraction of those measured. By 780 days, trace element concentrations in the SEP fractions approached reference concentrations in the more bioavailable water soluble, ion exchangeable, and carbonate-bound fractions. For each trace element, the percentage composition of the bioavailable fractions relative to the total concentration was calculated. These SEP indices were summed and shown to significantly decrease over time. These results document the natural attenuation of leachable trace elements in CCPs in river sediment as a result of the loss of bioavailable trace elements over time. PMID:24756414

  18. Polycyclic aromatic hydrocarbons in Australian coals. I. Angularly fused pentacyclic tri- and tetraaromatic components of Victorian brown coal

    NASA Astrophysics Data System (ADS)

    Chaffee, Alan L.; Johns, R. B.

    1983-12-01

    Analysis of the tri- and tetraaromatic hydrocarbon fractions of a brown coal sample from the Latrobe Valley, Victoria, Australia indicate the predominance of pentacyclic hydroaromatic components. Many of these have not been previously reported in the literature, but are obviously diagenetically related to triterpenoids naturally occurring in the biosphere. The components whose molecular structures have been confirmed, together with those for which tentative structural assignments are given, offer strong support for a theory of progressive diagenetic aromatization of C-3 oxygenated triterpenoids, commencing from ring A. Other compounds present in smaller amounts suggest that 1,2-methyl shift reactions also occur prior to or during aromatization. There is a notable absence of polycyclic aromatic hydrocarbons (PAH's) which can be diagenetically related to the steroid or extended-side-chain hopane skeletons.

  19. Zinc isotopic composition of particulate matter generated during the combustion of coal and coal + tire-derived fuels.

    PubMed

    Borrok, David M; Gieré, Reto; Ren, Minghua; Landa, Edward R

    2010-12-01

    Atmospheric Zn emissions from the burning of coal and tire-derived fuel (TDF) for power generation can be considerable. In an effort to lay the foundation for tracking these contributions, we evaluated the Zn isotopes of coal, a mixture of 95 wt % coal + 5 wt % TDF, and the particulate matter (PM) derived from their combustion in a power-generating plant. The average Zn concentrations and δ(66)Zn were 36 mg/kg and 183 mg/kg and +0.24‰ and +0.13‰ for the coal and coal + TDF, respectively. The δ(66)Zn of the PM sequestered in the cyclone-type mechanical separator was the lightest measured, -0.48‰ for coal and -0.81‰ for coal+TDF. The δ(66)Zn of the PM from the electrostatic precipitator showed a slight enrichment in the heavier Zn isotopes relative to the starting material. PM collected from the stack had the heaviest δ(66)Zn in the system, +0.63‰ and +0.50‰ for the coal and coal + TDF, respectively. Initial fractionation during the generation of a Zn-rich vapor is followed by temperature-dependent fractionation as Zn condenses onto the PM. The isotopic changes of the two fuel types are similar, suggesting that their inherent chemical differences have only a secondary impact on the isotopic fractionation process. PMID:21047059

  20. Zinc isotopic composition of particulate matter generated during the combustion of coal and coal + tire-derived fuels

    USGS Publications Warehouse

    Borrok, D.M.; Gieré, R.; Ren, M.; Landa, E.R.

    2010-01-01

    Atmospheric Zn emissions from the burning of coal and tire-derived fuel (TDF) for power generation can be considerable. In an effort to lay the foundation for tracking these contributions, we evaluated the Zn isotopes of coal, a mixture of 95 wt % coal + 5 wt % TDF, and the particulate matter (PM) derived from their combustion in a power-generating plant. The average Zn concentrations and δ(66)Zn were 36 mg/kg and 183 mg/kg and +0.24‰ and +0.13‰ for the coal and coal + TDF, respectively. The δ(66)Zn of the PM sequestered in the cyclone-type mechanical separator was the lightest measured, -0.48‰ for coal and -0.81‰ for coal+TDF. The δ(66)Zn of the PM from the electrostatic precipitator showed a slight enrichment in the heavier Zn isotopes relative to the starting material. PM collected from the stack had the heaviest δ(66)Zn in the system, +0.63‰ and +0.50‰ for the coal and coal + TDF, respectively. Initial fractionation during the generation of a Zn-rich vapor is followed by temperature-dependent fractionation as Zn condenses onto the PM. The isotopic changes of the two fuel types are similar, suggesting that their inherent chemical differences have only a secondary impact on the isotopic fractionation process.

  1. Development and evaluation of coal/water mixture combustion technology. Final report

    SciTech Connect

    Scheffee, R.S.; Rossmeissl, N.P.; Skolnik, E.G.; McHale, E.T.

    1981-08-01

    The objective was to advance the technology for the preparation, storage, handling and combustion of highly-loaded coal/water mixtures. A systematic program to prepare and experimentally evaluate coal/water mixtures was conducted to develop mixtures which (1) burn efficiently using combustion chambers and burners designed for oil, (2) can be provided at a cost less than that of No. 6 oil, and (3) can be easily transported and stored. The program consisted of three principal tasks. The first was a literature survey relevant to coal/water mixture technology. The second involved slurry preparation and evaluation of rheological and stability properties, and processing techniques. The third consisted of combustion tests to characterize equipment and slurry parameters. The first task comprised a complete search of the literature, results of which are tabulated in Appendix A. Task 2 was involved with the evaluation of composition and process variables on slurry rheology and stability. Three bituminous coals, representing a range of values of volatile content, ash content, and hardness were used in the slurries. Task 3 was concerned with the combustion behavior of coal/water slurry. The studies involved first upgrading of an experimental furnace facility, which was used to burn slurry fuels, with emphasis on studying the effect on combustion of slurry properties such as viscosity and particle size, and the effect of equipment parameters such as secondary air preheat and atomization.

  2. A low emission technology -- low cost coal water mixture fired fluidized bed combustion

    SciTech Connect

    Jianhua Yan; Xuguang Jiang; Yong Chi

    1995-12-31

    In this paper, low cost coal water mixture (CWM) FBC technology is described. Low cost CWM may be coal washery sludge or the mixture of water and coal crashed easily. This technology is featured by agglomerate combustion of low cost MM. Experimental results in 0.5MW FBC test rig are reported. lie effects of bed temperate excess air, staged combustion on combustion and emission performance has been studied. The comparison combustion tests by using dry coal and CWM we made ha 0.5MW FBC test rig. Also coal washery sludge of different origins are also tested in the test rig. Based on the test rig comments a demonstration AFBC boiler with capacity of 35 T/H steam for utility application (6 MW) is designed. The design features will be presented in this paper Both the operation experience of test rig and demonstration unit show the developed low cost CWM FBC technology is of high combustion efficiency and low emission. This technology is being commercialized and applied in China in top priority by Chinese government.

  3. Combustion characterization of beneficiated coal-based fuels. Quarterly report No. 8, January--March 1991

    SciTech Connect

    Chow, O.K.; Nsakala, N.Y.

    1991-07-01

    The Pittsburgh Energy Technology Center of the US Department of Energy has contracted with Combustion Engineering, Inc. (CE) to perform a five-year project on ``Combustion Characterization of Beneficiated Coal-Based Fuels.`` The beneficiated coals are produced by other contractors under the DOE Coal Preparation Program. Several contractor-developed advanced coal cleaning processes are run at pilot-scale cleaning facilities to produce 20-ton batches of fuels for shipment to CE`s laboratory in Windsor, Connecticut. CE then processes the products into either a coal-water fuel (CWF) or a dry microfine pulverized coa1 (DMPC) form for combustion testing. The objectives of this project include: (1) the development of an engineering data base which will provide detailed information on the properties of BCFs influencing combustion, ash deposition, ash erosion, particulate collection, and emissions; and (2) the application of this technical data base to predict the performance and economic impacts of firing the BCFs in various commercial boiler designs. During the third quarter of 1991, the following technical progress was made: Calculated the kinetic characteristics of chars from the combustion of spherical oil agglomeration beneficiated products; continued drop tube devolatilization tests of the spherical oil agglomeration beneficiated products; continued analyses of the data and samples from the CE pilot-scale tests of nine fuels; and started writing a summary topical report to include all results on the nine fuels tested.

  4. Combustion characterization of beneficiated coal-based fuels. Quarterly report No. 16, January--March 1993

    SciTech Connect

    Chow, O.K.; Nsakala, N.Y.

    1993-05-01

    The Pittsburgh Energy Technology Center of the US Department of Energy has contracted with Combustion Engineering, Inc. (CE) to perform a five-year project on ``Combustion Characterization of Beneficiated Coal-Based Fuels.`` The beneficiated coals are produced by other contractors under the DOE Coal Preparation Program. Several contractor-developed advanced coal cleaning processes are run at pilot-scale cleaning facilities to produce 20-ton batches of fuels for shipment to CE`s laboratory in Windsor, Connecticut. CE then processes the products into either a coal-water fuel (CWF) or a dry microfine pulverized coa1 (DMPC) form for combustion testing. The objectives of this project include: (1) the development of an engineering data base which will provide detailed information on the properties of BCFs influencing combustion, ash deposition, ash erosion, particulate collection, and emissions; and (2) the application of this technical data base to predict the performance and economic impacts of firing the BCFs in various commercial boiler designs. The technical approach used to develop the technical data includes: bench-scale fuel property, combustion, and ash deposition tests; pilot-scale combustion and ash effects tests; and full-scale combustion tests. During the first quarter of 1993, the following technical progress was made: Reported results of drop tube furnace data analyses to determine devolatilization kinetics; reported the results from the re-analyzed pilot-scale ash deposits from the first nine feed coals and BCFs using a modified CCSEM technique; and prepared for upcoming tests of new BCFs being produced.

  5. Combustion characterization of beneficiated coal-based fuels. Quarterly report No. 13, April--June 1992

    SciTech Connect

    Chow, O.K.; Nsakala, N.Y.

    1992-09-01

    The Pittsburgh Energy Technology Center of the US Department of Energy has contracted with Combustion Engineering, Inc. (CE) to perform a five-year project on ``Combustion Characterization of Beneficiated Coal-Based Fuels.`` The beneficiated coals are produced by other contractors under the DOE Coal Preparation Program. Several contractor-developed advanced coal cleaning processes are run at pilot-scale cleaning facilities to produce 20-ton batches of fuels for shipment to CE`s laboratory in Windsor, Connecticut. CE then processes the products into either a coal-water fuel (CWF) or a dry microfine pulverized coa1 (DMPC) form for combustion testing. The objectives of this project include: (1) the development of an engineering data base which will provide detailed information on the properties of BCFs influencing combustion, ash deposition, ash erosion, particulate collection, and emissions; and (2) the application of this technical data base to predict the performance and economic impacts of firing the BCFs in various commercial boiler designs. The technical approach used to develop the technical data includes: bench-scale fuel property, combustion, and ash deposition tests; pilot-scale combustion and ash effects tests; and full-scale combustion tests. During the third quarter of 1992, the following technical progress was made: Continued analyses of drop tube furnace samples to determine devolatilization kinetics; completed analyses of the samples from the pilot-scale ash deposition tests of unweathered Upper Freeport feed coal; published two technical papers at conferences; and prepared for upcoming tests of new BCFs being produced.

  6. Combustion characterization of beneficiated coal-based fuels. Quarterly report No. 15, October--December 1992

    SciTech Connect

    Chow, O.K.; Nsakala, N.Y.

    1993-03-01

    The Pittsburgh Energy Technology Center of the US Department of Energy has contracted with Combustion Engineering, Inc. (CE) to perform a five-year project on ``Combustion Characterization of Beneficiated Coal-Based Fuels.`` The beneficiated coals are produced by other contractors under the DOE Coal Preparation Program. Several contractor-developed advanced coal cleaning processes are run at pilot-scale cleaning facilities to produce 20-ton batches of fuels for shipment to CE`s laboratory in Windsor, Connecticut. CE then processes the products into either a coal-water fuel (CWF) or a dry microfine pulverized coa1 (DMPC) form for combustion testing. The objectives of this project include: (1) the development of an engineering data base which will provide detailed information on the properties of BCFs influencing combustion, ash deposition, ash erosion, particulate collection, and emissions; and (2) the application of this technical data base to predict the performance and economic impacts of firing the BCFs in various commercial boiler designs. The technical approach used to develop the technical data includes: bench-scale fuel property, combustion, and ash deposition tests; pilot-scale combustion and ash effects tests; and full-scale combustion tests. During the third quarter of 1992, the following technical progress was made: Continued analyses of drop tube furnace samples to determine devolatilization kinetics; re-analyzed the samples from the pilot-scale ash deposition tests of the first nine feed coals and BCFs using a modified CCSEM technique; updated the topical summary report; and prepared for upcoming tests of new BCFs being produced.

  7. Emissions from carpet combustion in a pilot-scale rotary kiln: comparison with coal and particle-board combustion

    SciTech Connect

    Stephanie Lucero Konopa; James A. Mulholland; Matthew J. Realff; Paul M. Lemieux

    2008-08-15

    The use of post-consumer carpet as a potential fuel substitute in cement kilns and other high-temperature processes is being considered to address the problem of huge volumes of carpet waste and the opportunity of waste-to-energy recovery. Carpet represents a high volume waste stream, provides high energy value, and contains other recoverable materials for the production of cement. This research studied the emission characteristics of burning 0.46-kg charges of chopped nylon carpet squares, pulverized coal, and particle-board pellets in a pilot-scale natural gas-fired rotary kiln. Carpet was tested with different amounts of water added. Emissions of oxygen, carbon dioxide, nitric oxide (NO), sulfur dioxide (SO{sub 2}), carbon monoxide (CO), and total hydrocarbons and temperatures were continuously monitored. It was found that carpet burned faster and more completely than coal and particle board, with a rapid volatile release that resulted in large and variable transient emission peaks. NO emissions from carpet combustion ranged from 0.06 to 0.15 g/MJ and were inversely related to CO emissions. Carpet combustion yielded higher NO emissions than coal and particleboard combustion, consistent with its higher nitrogen content. S{sub 2} emissions were highest for coal combustion, consistent with its higher sulfur content than carpet or particle board. Adding water to carpet slowed its burn time and reduced variability in the emission transients, reducing the CO peak but increasing NO emissions. Results of this study indicate that carpet waste can be used as an effective alternative fuel, with the caveats that it might be necessary to wet carpet or chop it finely to avoid excessive transient puff emissions due to its high volatility compared with other solid fuels, and that controlled mixing of combustion air might be used to control NO emissions from nylon carpet. 13 refs., 5 figs., 1 tab.

  8. Combustion characterization of beneficiated coal-based fuels. Quarterly report No. 9, April--June 1991

    SciTech Connect

    Chow, O.K.; Nsakala, N.Y.

    1991-08-01

    The Pittsburgh Energy Technology Center of the US Department of Energy has contracted with Combustion Engineering, Inc. (CE) to perform a five-year project on ``Combustion Characterization of Beneficiated Coal-Based Fuels.`` The beneficiated coals are produced by other contractors under the DOE Coal Preparation Program. Several contractor-developed advanced coal cleaning processes are run at pilot-scale cleaning facilities to produce 20-ton batches of fuels for shipment to CE`s laboratory in Windsor, Connecticut. CE then processes the products into either a coal-water fuel (CWF) or a dry microfine pulverized coa1 (DMPC) form for combustion testing. The objectives of this project include: (1) the development of an engineering data base which will provide detailed information on the properties of BCFs influencing combustion, ash deposition, ash erosion, particulate collection, and emissions; and (2) the application of this technical data base to predict the performance and economic impacts of firing the BCFs in various commercial boiler designs. During the second quarter of 1991, the following technical progress was made: completed drop tube furnace devolatilization tests of the spherical oil agglomeration beneficiated products; continued analyses of samples to determine devolatilization kinetics; continued analyses of the data and samples from the CE pilot-scale tests of nine fuels; completed writing a summary topical report including all results to date on he nine fuels tested; and presented three technical papers on the project results at the 16th International Conference on Coal & Slurry Technologies.

  9. Evaluation of coal-gasification - combustion-turbine power plants emphasizing low water consumption

    SciTech Connect

    Cavazo, R.; Clemmer, A.B.; de la Mora, J.A.; Grisso, J.R.; Klumpe, H.W.; Meissner, R.E.; Musso, A.; Roszkowski, T.R.

    1982-01-01

    A cost and performance study was made of several integrated power plants using coal gasification technology now in advanced development and combustion turbines for power generation. The principal emphasis was placed on studying plants using air cooling and comparing costs and performance of those plants with water-cooled coal gasification-combined-cycle (GCC) and conventional coal-fired power plants. The major objective was to determine whether cost and performance penalties would be prohibitive for air-cooled plants that use yet-to-be-developed coal gasifiers and commercially available combustion turbines for topping cycle power. The results indicate the following: air-cooled GCC plants using conceptual designs of either the Texaco or the British Gas Corporation (BGC) slaging gasifier could have coal-to-net electric power efficiencies equivalent to that of a water-cooled conventional coal-fired plant; the air-cooled GCC plants could produce electricity at busbar cost 1 to 3 mills per kWh (1980 dollars) less than busbar cost in a water-cooled conventional plant and only up to 2 mills per kWh higher than busbar cost in a water-cooled Texaco GCC plant; and even a simple-cycle regenerative combustion turbine plant fueled with gas from the BGC gasifier could have a coal-to-net electric power efficiency of over 30% and a busbar cost competitive with that in a water cooled conventional plant. The principal reason that air-cooled power plants using combustion turbines could be competitive with conventional water-cooled, coal-fired steam plants is that a majority of net power is produced by the combustion turbines, which require no cooling water. This, in turn, leads to a reduced cost and performance penalty when bottoming steam-cycle condensers are air-cooled.

  10. Combustion characteristics of Malaysian oil palm biomass, sub-bituminous coal and their respective blends via thermogravimetric analysis (TGA).

    PubMed

    Idris, Siti Shawalliah; Rahman, Norazah Abd; Ismail, Khudzir

    2012-11-01

    The combustion characteristics of Malaysia oil palm biomass (palm kernel shell (PKS), palm mesocarp fibre (PMF) and empty fruit bunches (EFB)), sub-bituminous coal (Mukah Balingian) and coal/biomass blends via thermogravimetric analysis (TGA) were investigated. Six weight ratios of coal/biomass blends were prepared and oxidised under dynamic conditions from temperature 25 to 1100°C at four heating rates. The thermogravimetric analysis demonstrated that the EFB and PKS evolved additional peak besides drying, devolatilisation and char oxidation steps during combustion. Ignition and burn out temperatures of blends were improved in comparison to coal. No interactions were observed between the coal and biomass during combustion. The apparent activation energy during this process was evaluated using iso-conversional model free kinetics which resulted in highest activation energy during combustion of PKS followed by PMF, EFB and MB coal. Blending oil palm biomass with coal reduces the apparent activation energy value. PMID:22944493

  11. Development and testing of commercial-scale, coal-fired combustion systems: Phase III. Final report

    SciTech Connect

    1996-03-01

    Based on studies that indicated a large potential for significantly increased coal-firing in the commercial sector, the U.S. Department of Energy`s Pittsburgh Energy Technology Center (PETC) sponsored a multi-phase development effort for advanced coal combustion systems. This Final Report presents the results of the last phase (Phase III) of a project for the development of an advanced coal-fired system for the commercial sector of the economy. The project performance goals for the system included dual-fuel capability (i.e., coal as primary fuel and natural gas as secondary fuel), combustion efficiency exceeding 99 percent, thermal efficiency greater than 80 percent, turndown of at least 3:1, dust-free and semi-automatic dry ash removal, fully automatic start-up with system purge and ignition verification, emissions performance exceeding New Source Performance Standards (NSPS) and approaching those produced by oil-fired, Commercial-sized units, and reliability, safety, operability, maintainability, and service life comparable to oil-fired units. The program also involved a site demonstration at a large facility owned by Striegel Supply Company, a portion of which was leased to MTCI. The site, mostly warehouse space, was completely unheated and the advanced coal-fired combustion system was designed and sized to heat this space. Three different coals were used in the project, one low and one high sulfur pulverized Pittsburgh No. 8 coal, and a micronized low volatile, bituminous coal. The sorbents used were Pfizer dolomitic limestone and an Anvil lime. More than 100 hours of screening test`s were performed to characterize the system. The parameters examined included coal firing rate, excess air level, ash recycle rate, coal type, dolomitic limestone feed rate, and steam injection rate. These tests indicated that some additional modifications for coal burning in the system were required.

  12. Coal combustion under conditions of blast furnace injection; [Quarterly] technical report, September 1--November 30, 1993

    SciTech Connect

    Crelling, J.C.

    1993-12-31

    A potentially new use for Illinois coal is its use as a fuel injected into a blast furnace to produce molten iron as the first step in steel production. Because of its increasing cost and decreasing availability, metallurgical coke is now being replaced by coal injected at the tuyere area of the furnace where the blast air enters. The purpose of this study is to evaluate the combustion of coal during the blast furnace injection process and to delineate the optimum properties of the feed coal. This investigation is significant to the use of Illinois coal in that the limited research to date suggests that coals of low fluidity and moderate to high sulfur and chlorine contents are suitable feedstocks for blast furnace injection. This study is unique in that it will be the first North American effort to directly determine the nature of the combustion of coal injected into a blast furnace. This proposal is a follow-up to one funded for the 1992--1993 period. It is intended to complete the study already underway with the Armco Inc. steel company and to initiate a new cooperative study along somewhat similar lines with the Inland Steel Company. The results of this study will lead to the development of a testing and evaluation protocol that will give a unique and much needed understanding of the behavior of coal in the injection process and prove the potential of Illinois coals f or such use.

  13. The mechanism controlling sticking ash separation and reentrainment in pulverized coal combustion products

    SciTech Connect

    Goldman, Y.; Greenberg, J.B.; Timnat, Y.M.

    1993-12-31

    One of the main areas of development and research in intensification of coal combustion involves burning of pulverized fuel. In this process the overall interaction surface between the reactants (oxygen and coal particles) is about two orders of magnitude bigger than in other methods (stokers, grates, fluidized beds, etc.); such systems of firing are suitable for a wide range of applications from power generation boilers to gas turbines. The ash formed during the combustion process has a strong influence on the combustion intensity and is particularly important for future applications to gas turbines, in a first stage for power generation and later for vehicle powerplants (trucks, ships, eventually airplanes). Improvement of combustion intensity in PF combustors can be attained by two basic techniques. The cyclone furnace is based on the use of tangential injection of air containing pulverized coal, so swirling motion of the combustion products is created in the combustion chamber, with intensive chemical reaction occurring in the boundary layers adjacent to the walls. Attempts were made to reduce NO{sub x} formation and to model mathematically the detailed flow and mixing processes in tangentially fired furnaces. The three-dimensional calculations supply valuable predictions concerning these processes but do not include combustion and heat transfer effects. However such effects can also be calculated. Recently Gillis and Smith evaluated a three-dimensional industrial furnace using a comprehensive code developed at Brigham Young University.

  14. Analysis of options for coal combustion waste management in the Pacific Basin

    SciTech Connect

    Elcock, D.; Gasper, J.

    1993-10-01

    Many Pacific Basin countries rely on oil for electricity production. Alternative fuel sources such as coal, which is available in the Pacific Basin, can help mitigate adverse impacts of sudden price increases or supply disruptions. Coal combustion produces solid and potentially hazardous wastes of concern to environmental regulators and utility managers. This paper identifies issues associated with managing coal combustion wastes in the Pacific Basin, using the state of Hawaii as a case study. Hawaii is typical of many Pacific Basin locations in that it depends on oil, has limited sites, for waste management operations, and is subject to domestic and international waste management regulations. The paper discusses coal-fired utility wastes, environmental impacts of coal combustion waste disposal, and regulatory requirements that impact coal waste management. From this baseline, potential on- and off-island options for coal waste management are identified. Waste management costs are estimated and non-quantifiable issues are addressed for each option. Many options are applicable across the Pacific Rim and may serve as a basis for future fuel-use decisions.

  15. Spontaneous combustion prediction of coal by C80 and ARC techniques

    SciTech Connect

    Qingsong Wang; Song Guo; Jinhua Sun

    2009-09-15

    Many coal fires were caused by spontaneous combustion in coal mines or coal storehouses, which resulted in a great loss and energy wastage. To identify and evaluate the hazardous degree of coal stockpile, a C80 microcalorimeter and accelerating rate calorimeter (ARC) were employed in this work. The coal samples undergo an exothermal process start at 80 {sup o}C with heat generation of -75.1 J g{sup -1} (mean value) detected by C80 experiment. The activation energies of the first exothermal process were calculated for the three experiments, and the mean value is 80.76 kJ mol{sup -1}, which is lower than that of obtained from the ARC result, 127.0 kJ mol{sup -1}. For a 300 tons coal stockpile, the self-heating oxidation temperatures (SHOT) were calculated as 164, 60, 90, and 68{sup o}C based on the ARC experiment and three C80 experiments, respectively. Further research on the mass effect on SHOT shows that if the coal mass is less than 12 tons, the danger of thermal spontaneous combustion is less. However, if the mass amount is more than 12000 tons, the danger of thermal spontaneous combustion is difficult to avoid even at ambient temperature if no special measures are taken. 38 refs., 9 figs.

  16. Modeling the behavior of selenium in Pulverized-Coal Combustion systems

    SciTech Connect

    Senior, Constance; Otten, Brydger Van; Wendt, Jost O.L.; Sarofim, Adel

    2010-11-15

    The behavior of Se during coal combustion is different from other trace metals because of the high degree of vaporization and high vapor pressures of the oxide (SeO{sub 2}) in coal flue gas. In a coal-fired boiler, these gaseous oxides are absorbed on the fly ash surface in the convective section by a chemical reaction. The composition of the fly ash (and of the parent coal) as well as the time-temperature history in the boiler therefore influences the formation of selenium compounds on the surface of the fly ash. A model was created for interactions between selenium and fly ash post-combustion. The reaction mechanism assumed that iron reacts with selenium at temperatures above 1200 C and that calcium reacts with selenium at temperatures less than 800 C. The model also included competing reactions of SO{sub 2} with calcium and iron in the ash. Predicted selenium distributions in fly ash (concentration versus particle size) were compared against measurements from pilot-scale experiments for combustion of six coals, four bituminous and two low-rank coals. The model predicted the selenium distribution in the fly ash from the pilot-scale experiments reasonably well for six coals of different compositions. (author)

  17. Investigation of the behavior of potentially hazardous trace elements in Kentucky coals and combustion byproducts

    SciTech Connect

    Robertson, J.D.; Blanchard, L.J.; Srikantapura, S.; Parekh, B.K.; Lafferty, C.J.

    1996-12-31

    The minor- and trace-element content of coal is of great interest because of the potentially hazardous impact on human health and the environment resulting from their release during coal combustion. Of the one billion tons of coal mined annually in the United States, 85-90% is consumed by coal-fired power plants. Potentially toxic elements present at concentrations as low as a few egg can be released in large quantities from combustion of this magnitude. Of special concern are those trace elements that occur naturally in coal which have been designated as potential hazardous air pollutants (HAPs) in the 1990 Amendments to the Clean Air Act. The principle objective of this work was to investigate a combination of physical and chemical coal cleaning techniques to remove 90 percent of HAP trace elements at 90 percent combustibles recovery from Kentucky No. 9 coal. Samples of this coal were first subjected to physical separation by flotation in a Denver cell. The float fraction from the Denver cell was then used as feed material for hydrothermal leaching tests in which the efficacy of dilute alkali (NaOH) and acid (HNO{sub 3}) solutions at various temperatures and pressures was investigated. The combined column flotation and mild chemical cleaning strategy removed 60-80% of trace elements with greater than 85, recovery of combustibles from very finely ground (-325 mesh) coal. The elemental composition of the samples generated at each stage was determined using particle induced X-ray emission (PIXE) analysis. PIXE is a rapid, instrumental technique that, in principle, is capable of analyzing all elements from sodium through uranium with sensitivities as low as 1 {mu}g/g.

  18. MUTATION SPECTRA OF SMOKY COAL COMBUSTION EMMISSIONS IN SALMONELLA REFLECTS THE TP53 AND KRAS MUTATIONS IN LUNG TUMORS FROM SMOKY COAL EXPOSED INDIVIDUALS

    EPA Science Inventory


    Mutation Spectra of Smoky Coal Combustion Emissions in Salmonella Reflect the TP53
    and KRAS Mutations in Lung Tumors from Smoky Coal-Exposed Individuals

    Abstract
    Nonsmoking women in Xuan Wei County, Yunnan Province, China who use smoky coal for cooking and h...

  19. An investigation of the organic matter of the fulvic acids from weathered brown coal by pyrolytic mass spectrometry

    SciTech Connect

    Rumyantseva, Z.A.; Gal'chenko, A.I.; Khmel'nitskii, R.A.; Lukashenko, I.M.

    1983-01-01

    The molecules of the fulvic acids of weathered brown coal contain very large amounts of oxygen- and sulfur-containing functional groups. In the aromatic structures of the part of them that was studied derivatives of monocyclic aromatics predominate and a considerable role is played by sulfonic acid structures.

  20. Coal combustion: Effect of process conditions on char reactivity

    SciTech Connect

    Zygourakis, K.

    1991-01-01

    The project will quantify the effect of the following pyrolysis conditions on the macropore structure and on the subsequent reactivity of chars: (a) pyrolysis heating rate; (b) final heat treatment temperature (HTT); (c) duration of heat treatment at HTT (or soak time); (d) pyrolysis atmosphere (N{sub 2} or O{sub 2}/N{sub 2} mixtures); (e) coal particle size (100 {endash} 1000 {mu}m in diameter); (f) sulfur-capturing additives (limestone); and (g) coal rank. Pyrolysis experiments will be carried out for three coals from the Argonne collection: (1) a high-volatile bituminous coal with high ash content (Illinois {number sign}6), (2) a bituminous coal with low ash content (Utah Blind Canyon) and (3) a lower rank subbituminous coal (Wyodak-Anderson seam).

  1. Coal combustion: Effect of process conditions on char reactivity

    SciTech Connect

    Zygourakis, K.

    1992-01-01

    The project will quantify the effect of the following pyrolysis conditions on the macropore structure and on the subsequent reactivity of chars: (a) pyrolysis heating rate; (b) final heat treatment temperature (HTT); (c) duration of heat treatment at HTT (or soak time); (d) pyrolysis atmosphere (N{sub 2} or O{sub 2}/N{sub 2} mixtures); (e) coal particle size (100--1,000 {mu}m in diameter); (f) sulfur-capturing additives (limestone); and (g) coal rank. Pyrolysis experiments will be carried out for three coals from the Argonne collection: (1) a high-volatile bituminous coal with high ash content (Illinois {number sign}6), (2) a bituminous coal with low ash content (Utah Blind Canyon) and (3) a lower rank subbituminous coal (Wyodak-Anderson seam). (VC)

  2. Combustion characterization of beneficiated coal-based fuels

    SciTech Connect

    Chow, O.K.; Nsakala, N.Y.

    1990-06-01

    The objectives of this project include: (1) the development of an engineering data base which will provide detailed information on the properties of BCFs influencing combustion, ash deposition, ash erosion, particulate collection, and missions; and (2) the application of this technical data base to predict the performance and economic impacts of firing the BCFs in various commercial boiler designs. The technical approach used to develop the technical data includes: bench-scale fuel property, combustion, and ash deposition tests; pilot-scale combustion and ash effects test; and full-scale combustion tests.

  3. Leaching of coal combustion products: Field and laboratory studies

    NASA Astrophysics Data System (ADS)

    Cheng, Chin-Min

    This study combines field monitoring and laboratory experiments to investigate the environmental impacts associated with the re-use of coal combustion by-products (CCPs). The monitoring data obtained from two full-scale CCP applications (i.e., re-use of fixated flue gas desulfurization (FGD) material as a low permeability liner for a swine manure pond and portland cement concrete pavements containing CCPs) allowed environmental impacts to be evaluated under real or simulated in-service conditions. A complimentary laboratory leaching study elucidated fundamental physical and chemical mechanisms that determine the leaching kinetics of inorganic contaminants from CCPs. In the first field study, water quality impacts associated with the re-use of FGD material as a low permeability liner for a swine manure pond were examined by monitoring the water quality of water samples collected from the pond surface water and a sump collection system beneath the liner over a period of 5 years. Water samples collected from the sump and pond surface water met all Ohio non-toxic criteria, and in fact, generally met all national primary and secondary drinking water standards. Furthermore it was found that hazardous (i.e., As, B, Cr, Cu, and Zn) and agricultural pollutants (i.e., phosphate and ammonia) were effectively retained by the FGD liner system. The retention might be due to both sorption and precipitation. In the second field study, the release of metals and metalloids from full-scale portland cement concrete pavements containing CCPs was evaluated by laboratory leaching tests and accelerated loading of full-scale pavement sections under controlled loading and environmental conditions. Three types of portland-cement-concrete driving surfaces were tested, including a control section (i.e., ordinary portland cement (OPC) concrete) containing no fly ash and two sections in which fly ash was substituted for a fraction of the cement; i.e., 30% fly ash (FA30) and 50% fly ash (FA50

  4. Combustion of coal in an opposed gas-particle jet with regenerative pyrolysis. Final report

    SciTech Connect

    Durbetaki, P.

    1980-08-31

    The burning of coal particles is the coupled effect of the interlinked processes of pyrolysis, ignition and combustion of the volatiles and char. The specific objectives for the current research program are: (i) to establish an operating system with regenerative pyrolysis, (ii) to identify the primary parameters which effect the pyrolysis, ignition and combustion of the particles in this system, (iii) to identify measurements which are needed and techniques to be developed for these measurements, and (iv) to establish a preliminary basis for a modeling analysis. The present studies carried out with the flat flame burner and the opposed gas-particle jet have shown the feasibility of studying the ignition of pyrolyzate and coal particles. These were found to be affected by the level of preheating, composition of carrier gas and type of fuel particle. The behavior of lignite particles compared to bituminous particles were found to be distinctly different. Pyrolysis experiments carried out on the two coals at heating rates near those experienced with regenerative pyrolysis, have shown that self-ignition temperatures of fuel lean mixtures are not effected by the variable considered in this investigation. Sooting was found to accompany the combustion of bituminous coal particles and not of the lignite particles. Also higher gas-particle rates were found to be needed to self-sustain the combustion of bituminous coal particles than those required for lignite coal particles. These preliminary studies in the three areas of ignition, pyrolysis and combustion have shown the need to use additional instrumentation to further quantify the behavior of these coal particles under regenerative pyrolysis conditions.

  5. Physico-chemical and optical properties of combustion-generated particles from coal-fired power plant, automobile and ship engine and charcoal kiln.

    NASA Astrophysics Data System (ADS)

    Kim, Hwajin

    2015-04-01

    -temperature (~300-800 °C) combustion conditions. Depending on burning sources, significantly different optical properties were observed; diesel combustion particles from automobile and ship showed wavelength independent absorbing properties whereas the particles from coal and charcoal kiln combustion showed the enhanced absorption at shorter wavelength which is a brown carbon characteristic. Our findings suggest that source dependent properties and distributions across the globe should be considered when their impacts on climate change and air qualities are discussed.

  6. Indoor air sampling and mutagenicity studies related to emissions from unvented coal combustion

    SciTech Connect

    Mumford, J.L.; Harris, D.B.; Williams, K.; Chuang, J.C.; Cooke, M.

    1986-07-01

    The purpose of the study is to develop sampling strategies and bioassay methods for indoor air in homes. The work reported here was conducted to prepare for a joint U.S.-China field study in Xuan Wei County, Yunnan Province, southern China, where the residents traditionally burn coal or wood for domestic cooking and heating without flue ventilation. These residents are exposed daily to high levels of combustion smoke and have unusually high lung cancer mortality rates, the women's rate the highest in China, and the men's rate among the highest. The paper reports the chemical and biological characterization of coal emissions from a simulated combustion laboratory.

  7. Co-combustion of solid recovered fuels in coal-fired power plants.

    PubMed

    Thiel, Stephanie; Thomé-Kozmiensky, Karl Joachim

    2012-04-01

    Currently, in ten coal-fired power plants in Germany solid recovered fuels from mixed municipal waste and production-specific commercial waste are co-combusted and experiments have been conducted at other locations. Overall, in 2010 approximately 800,000 tonnes of these solid recovered fuels were used. In the coming years up to 2014 a slight decline in the quantity of materials used in co-combustions is expected. The co-combustion activities are in part significantly influenced by increasing power supply from renewable sources of energy and their impact on the regime of coal-fired power plants usage. Moreover, price trends of CO₂ allowances, solid recovered fuels as well as imported coal also have significant influence. In addition to the usage of solid recovered fuels with biogenic content, the co-combustion of pure renewable biofuels has become more important in coal-fired power plants. The power plant operators make high demands on the quality of solid recovered fuels. As the operational experience shows, a set of problems may be posed by co-combustion. The key factors in process engineering are firing technique and corrosion. A significant ecological key factor is the emission of pollutants into the atmosphere. The results of this study derive from research made on the basis of an extensive literature search as well as a survey on power plant operators in Germany. The data from operators was updated in spring 2011. PMID:22143900

  8. Combustion test for RDF and coal in the 1.3 MWth ACFB

    SciTech Connect

    Kajita, A.; Tanaka, T.; Narukawa, K.; Kobayashi, N.; Nishiyama, A.; Oide, M.

    1999-07-01

    The diversification of fuel for the generating electricity becomes necessary to secure long-term energy. In this situation, coal is very important fuel resource because of great quantity of reserves under the ground and wide production area over the world. Therefore, the development of the high efficiency burning technology of coal fuel is required. The city garbage is also useful energy resource and it is socially expected the effective utilization technology with renewal energy and good for the environment. In such a background, it becomes important to know the combustion performance of RDF (Refuse Derived Fuel) in a efficient way with minimizing pollutant emissions. The authors conducted the coal and RDF burn tests using the 1.3 MW{sub th} ACFB (Atmospheric Circulating Fluidized-Bed) combustion test facility. The tests were conducted for both of 100% RDF combustion and combination of coal and RDF combustion with varied Ca contents and varied Cl contents in RDF. During combustion test, NO{sub x}, SO{sub 2} and HCl emissions in flue gas were measured. The result of the tests is reported and discussed in this paper.

  9. Combustion characterization of beneficiated coal-based fuels. Quarterly report No. 10, July--September 1991

    SciTech Connect

    Chow, O.K.; Nsakala, N.Y.

    1991-11-01

    The Pittsburgh Energy Technology Center of the US Department of Energy has contracted with Combustion Engineering, Inc. (CE) to perform a five-year project on ``Combustion Characterization of Beneficiated Coal-Based Fuels.`` The beneficiated coals are produced by other contractors under the DOE Coal Preparation Program. Several contractor-developed advanced coal cleaning processes are run at pilot-scale cleaning facilities to produce 20-ton batches of fuels for shipment to CE`s laboratory in Windsor, Connecticut. CE then processes the products into either a coal-water fuel (CWF) or a dry microfine pulverized coa1 (DMPC) form for combustion testing. The objectives of this project include: (1) the development of an engineering data base which will provide detailed information on the properties of BCFs influencing combustion, ash deposition, ash erosion, particulate collection, and emissions; and (2) the application of this technical data base to predict the performance and economic impacts of firing the BCFs in various commercial boiler designs. During the third quarter of 1991, the following technical progress was made: Continued analyses of drop tube furnace samples to determine devolatilization kinetics; completed analyses of the samples from the pilot-scale ash deposition tests of unweathered Upper Freeport fuels; completed editing of the first three quarterly reports and sent them to the publishing office; presented the project results at the Annual Contractors` Conference.

  10. Sublimation and combustion of coal particles in the erosion laser torch

    SciTech Connect

    Bulat, A.; Shumrikov, V.; Osenny, V.

    2005-07-01

    Rate of coal particles' combustion in low-temperature plasma is of interest both from application and scientific points of view. Necessity of knowing parameters of the process of coal particles' combustion in plasma torch with the temperature of 2500-3000 K is governed by arising a number of state-of-the-art technological tasks related to the problems of finding new methods of power production, generation of high-calorific synthetic gases and using carbon as a high temperature structural material in nuclear power engineering. The present work deals with a rate of combustion of the sorbed coal particles in the erosion laser torch formed by means of interaction of pulse laser radiation (wave length {lambda} = 1,06 {mu}m, power density j = 10{sup 5} - 10{sup 7} Wcm{sup 2} with coals of various grades (in the wide range of carbon concentrations (80-95 %)). Physical and mathematical modeling of the process of coal particles' sublimation and combustion in non-equilibrium plasma flows with weight-average temperature of 2500-3000 K showed a good convergence of results for the particles of 10-100 {mu}m diameter and satisfactory one for the particles of {gt} 250{mu}m diameter.

  11. Experimental research of sewage sludge with coal and biomass co-combustion, in pellet form.

    PubMed

    Kijo-Kleczkowska, Agnieszka; Środa, Katarzyna; Kosowska-Golachowska, Monika; Musiał, Tomasz; Wolski, Krzysztof

    2016-07-01

    Increased sewage sludge production and disposal, as well as the properties of sewage sludge, are currently affecting the environment, which has resulted in legislation changes in Poland. Based on the Economy Minister Regulation of 16 July 2015 (Regulation of the Economy Minister, 2015) regarding the criteria and procedures for releasing wastes for landfilling, the thermal disposal of sewage sludge is important due to its gross calorific value, which is greater than 6MJ/kg, and the problems that result from its use and application. Consequently, increasingly restrictive legislation that began on 1 January 2016 was introduced for sewage sludge storage in Poland. Sewage sludge thermal utilisation is an attractive option because it minimizes odours, significantly reduces the volume of starting material and thermally destroys the organic and toxic components of the off pads. Additionally, it is possible that the ash produced could be used in different ways. Currently, as many as 11 plants use sewage sludge as fuel in Poland; thus, this technology must be further developed in Poland while considering the benefits of co-combustion with other fuels. This paper presents the results of experimental studies of the mechanisms and kinetics of sewage sludge, coal and biomass combustion and their co-combustion in spherical-pellet form. Compared with biomass, a higher temperature is required to ignite sewage sludge by flame. The properties of biomass and sewage sludge result in the intensification of the combustion process (by fast ignition of volatile matter). In contrast to coal, a combustion of sewage sludge is determined not only burning the char, but also the combustion of volatiles. The addition of sewage sludge to hard coal and lignite shortens combustion times compared with coal, and the addition of sewage sludge to willow Salix viminalis produces an increase in combustion time compared with willow alone. PMID:27161507

  12. Effects of effluents of coal combustion and gasification upon lung structure and function. Annual report

    SciTech Connect

    Hinton, D.E.

    1980-01-01

    The overall objective of the proposed research is to correlate both structural and functional alterations in cells and tissues of the lung brought about by exposure to fluidized bed combustion and fixed bed gasification effluents and reagent grade oxides of metals known to be associated with coal combustion gasification. Projected milestones are described. Progress during the first year in setting up aerosol exposure facilities, intratracheal instillations, pulmonary mechanics, and morphometric examinations is reported. (DMC)

  13. NOx reduction in combustion with concentrated coal streams and oxygen injection

    DOEpatents

    Kobayashi, Hisashi; Bool, III, Lawrence E.; Snyder, William J.

    2004-03-02

    NOx formation in the combustion of solid hydrocarbonaceous fuel such as coal is reduced by obtaining, from the incoming feed stream of fuel solids and air, a stream having a ratio of fuel solids to air that is higher than that of the feed steam, and injecting the thus obtained stream and a small amount of oxygen to a burner where the fuel solids are combusted.

  14. Modeling coal combustion behavior in an ironmaking blast furnace raceway: model development and applications

    SciTech Connect

    Maldonado, D.; Austin, P.R.; Zulli, P.; Guo B.

    2009-03-15

    A numerical model has been developed and validated for the investigation of coal combustion phenomena under blast furnace operating conditions. The model is fully three-dimensional, with a broad capacity to analyze significant operational and equipment design changes. The model was used in a number of studies, including: Effect of cooling gas type in coaxial lance arrangements. It was found that oxygen cooling improves coal burnout by 7% compared with natural gas cooling under conditions that have the same amount of oxygen enrichment in the hot blast. Effect of coal particle size distribution. It was found that during two similar periods of operation at Port Kembla's BF6, a difference in PCI capability could be attributed to the difference in coal size distribution. Effect of longer tuyeres. Longer tuyeres were installed at Port Kembla's BF5, leading to its reline scheduled for March 2009. The model predicted an increase in blast velocity at the tuyere nose due to the combustion of volatiles within the tuyere, with implications for tuyere pressure drop and PCI capability. Effect of lance tip geometry. A number of alternate designs were studied, with the best-performing designs promoting the dispersion of the coal particles. It was also found that the base case design promoted size segregation of the coal particles, forcing smaller coal particles to one side of the plume, leaving larger coal particles on the other side. 11 refs., 15 figs., 4 tabs.

  15. Airfoil cooling hole plugging by combustion gas impurities of the type found in coal derived fuels

    NASA Technical Reports Server (NTRS)

    Deadmore, D. L.; Lowell, C. E.

    1979-01-01

    The plugging of airfoil cooling holes by typical coal-derived fuel impurities was evaluated using doped combustion gases in an atmospheric pressure burner rig. Very high specific cooling air mass flow rates reduced or eliminated plugging. The amount of flow needed was a function of the composition of the deposit. It appears that plugging of film-cooled holes may be a problem for gas turbines burning coal-derived fuels.

  16. Thermodynamic analysis of the behavior of microimpurities of toxic metals in coal combustion products

    SciTech Connect

    G.Ya. Gerasimov

    2004-01-15

    The thermodynamic approach to the description of the fuel-oxidizer system is used to elucidate the basic laws of behavior of compounds of the most toxic elements/microimpurities in combustion products of coal (Hg, Pb, Cr, Mn, Ni, Co, and As). It has been shown that the distribution of elements over components of the gas and condensed phases strongly depends on the process temperature and the composition of the mineral part of the coal.

  17. Application of Fourier-transform infrared (FT-ir) spectroscopy to in-situ studies of coal combustion

    SciTech Connect

    Ottesen, D K; Thorne, L R

    1982-04-01

    The feasibility of using Fourier-transform infrared (FT-ir) spectroscopy for in situ measurement of gas phase species concentrations and temperature during coal combustion is examined. This technique is evaluated in terms of its potential ability to monitor several important chemical and physical processes which occur in pulverized coal combustion. FT-ir absorption measurements of highly sooting, gaseous hydrocarbon/air flames are presented to demonstrate the fundamental usefulness of the technique for in situ detection of gas phase temperatures and species concentrations in high temperature combustion environments containing coal, char, mineral matter and soot particles. Preliminary results for coal/gaseous fuel/air flames are given.

  18. Effect of the size distribution of coal on fluidized-bed combustion

    SciTech Connect

    Hirama, T.; Hosoda, H.; Nishizaki, H.; Chiba, T.; Kobayashi, H.

    1984-07-01

    To study the effect of the particle-size distribution on its combustion characteristics, coal was burned in a 0.25 m-square fluidized-bed combustor with a 3-m freeboard. A higher fines content increased the loss of unburned coal by elutriation, but reduced the loss from overflow from the bed surface. The overall combustion efficiency varied only slightly with the size distribution; the efficiency of combustion within the bed was reduced, but more combustion took place in the freeboard, both for 9.5-25 mm particles, owing to segregation in the bed, and for <2 mm particles, owing to elutriation. NO/SUB/x emission for two-stage combustion with these two size ranges was considerably higher than for particles within the broader range <25 mm. Since segregation of coarse particles and elutriation of unburned finer particles increase NO/SUB/x emission and reduced the bed combustion efficiency, it is desirable to use coal with a broad particle-size distribution.

  19. Comparative study of combustion product emissions of Pakistani coal briquettes and traditional Pakistani domestic fuels

    SciTech Connect

    Wachter, E.A.; Gammage, R.B.; Haas, J.W. III; Wilson, D.L.; DePriest, J.C.; Wade, J.; Ahmad, N.; Sibtain, F.; Zahid Raza, M.

    1992-10-01

    A comparative emissions study was conducted on combustion products of various solid domestic cooking fuels; the objective was to compare relative levels of organic and inorganic toxic emissions from traditional Pakistani fuels (wood, wood charcoal, and dried animal dung) with manufactured low-rank coal briquettes (Lakhra and Sor- Range coals) under conditions simulating domestic cooking. A small combustion shed 12 m{sup 3} internal volume, air exchange rate 14 h{sup {minus}1} was used to simulate south Asian cooking rooms. 200-g charges of the various fuels were ignited in an Angethi stove located inside the shed, then combusted to completion; effluents from this combustion were monitored as a function of time. Measurements were made of respirable particulates, volatile and semi-volatile organics, CO, SO{sub 2}, and NO{sub x}. Overall it appears that emissions from coal briquettes containing combustion amendments (slaked lime, clay, and potassium nitrate oxidizer) are no greater than emissions from traditional fuels, and in some cases are significantly lower; generally, emissions are highest for all fuels in the early stages of combustion.

  20. Comparative study of combustion product emissions of Pakistani coal briquettes and traditional Pakistani domestic fuels

    SciTech Connect

    Wachter, E.A.; Gammage, R.B.; Haas, J.W. III; Wilson, D.L. ); DePriest, J.C.; Wade, J. ); Ahmad, N.; Sibtain, F.; Zahid Raza, M. )

    1992-10-01

    A comparative emissions study was conducted on combustion products of various solid domestic cooking fuels; the objective was to compare relative levels of organic and inorganic toxic emissions from traditional Pakistani fuels (wood, wood charcoal, and dried animal dung) with manufactured low-rank coal briquettes (Lakhra and Sor- Range coals) under conditions simulating domestic cooking. A small combustion shed 12 m[sup 3] internal volume, air exchange rate 14 h[sup [minus]1] was used to simulate south Asian cooking rooms. 200-g charges of the various fuels were ignited in an Angethi stove located inside the shed, then combusted to completion; effluents from this combustion were monitored as a function of time. Measurements were made of respirable particulates, volatile and semi-volatile organics, CO, SO[sub 2], and NO[sub x]. Overall it appears that emissions from coal briquettes containing combustion amendments (slaked lime, clay, and potassium nitrate oxidizer) are no greater than emissions from traditional fuels, and in some cases are significantly lower; generally, emissions are highest for all fuels in the early stages of combustion.

  1. Energy balance of the area influenced by brown coal mining in three phases

    SciTech Connect

    Hais, M.; Pecharova, M.; Svoboda, I.

    2005-07-01

    The change in the energy flow on land used for brown coal mining is examined. Terrain mapping was used to obtain land use data for a 14 km{sup 2} mining area and its surroundings. The focus is on the proportion of incident solar energy that is changed to latent heat during evapotranspiration. Each land use unit was assigned an average value for evapotranspiration for the growing season. Satellite data of surface temperature and surface wetness values show incident radiation converted to heat. Relationships between evapotranspiration and surface temperature and between wetness index and evapotranspiration were verified. The results confirm the hypothesis that changes in land use can have a significant effect on total average evapotranspiration. 18 refs., 5 figs., 3 tabs.

  2. Geochemical database of feed coal and coal combustion products (CCPs) from five power plants in the United States

    USGS Publications Warehouse

    Affolter, Ronald H.; Groves, Steve; Betterton, William J.; William, Benzel; Conrad, Kelly L.; Swanson, Sharon M.; Ruppert, Leslie F.; Clough, James G.; Belkin, Harvey E.; Kolker, Allan; Hower, James C.

    2011-01-01

    The principal mission of the U.S. Geological Survey (USGS) Energy Resources Program (ERP) is to (1) understand the processes critical to the formation, accumulation, occurrence, and alteration of geologically based energy resources; (2) conduct scientifically robust assessments of those resources; and (3) study the impacts of energy resource occurrence and (or) their production and use on both the environment and human health. The ERP promotes and supports research resulting in original, geology-based, non-biased energy information products for policy and decision makers, land and resource managers, other Federal and State agencies, the domestic energy industry, foreign governments, non-governmental groups, and academia. Investigations include research on the geology of oil, gas, and coal, and the impacts associated with energy resource occurrence, production, quality, and utilization. The ERP's focus on coal is to support investigations into current issues pertaining to coal production, beneficiation and (or) conversion, and the environmental impact of the coal combustion process and coal combustion products (CCPs). To accomplish these studies, the USGS combines its activities with other organizations to address domestic and international issues that relate to the development and use of energy resources.

  3. Preparation and evaluation of coal-derived activated carbons for removal of mercury vapor from simulated coal combustion flue fases

    USGS Publications Warehouse

    Hsi, H.-C.; Chen, S.; Rostam-Abadi, M.; Rood, M.J.; Richardson, C.F.; Carey, T.R.; Chang, R.

    1998-01-01

    Coal-derived activated carbons (CDACs) were tested for their suitability in removing trace amounts of vapor-phase mercury from simulated flue gases generated by coal combustion. CDACs were prepared in bench-scale and pilot-scale fluidized-bed reactors with a three-step process, including coal preoxidation, carbonization, and then steam activation. CDACs from high-organicsulfur Illinois coals had a greater equilibrium Hg0 adsorption capacity than activated carbons prepared from a low-organic-sulfur Illinois coal. When a low-organic-sulfur CDAC was impregnated with elemental sulfur at 600 ??C, its equilibrium Hg0 adsorption capacity was comparable to the adsorption capacity of the activated carbon prepared from the high-organicsulfur coal. X-ray diffraction and sulfur K-edge X-ray absorption near-edge structure examinations showed that the sulfur in the CDACs was mainly in organic forms. These results suggested that a portion of the inherent organic sulfur in the starting coal, which remained in the CDACs, played an important role in adsorption of Hg0. Besides organic sulfur, the BET surface area and micropore area of the CDACs also influenced Hg0 adsorption capacity. The HgCl2 adsorption capacity was not as dependent on the surface area and concentration of sulfur in the CDACs as was adsorption of Hg0. The properties and mercury adsorption capacities of the CDACs were compared with those obtained for commercial Darco FGD carbon.

  4. Combustion characterization of the blend of plant coal and recovered coal fines. Final technical report, September 1, 1991--August 31, 1992

    SciTech Connect

    Singh, S.; Scaroni, A.; Miller, B.; Choudhry, V.

    1992-12-31

    The overall objective of this proposed research program was to determine the combustion characteristics of the blend derived from mixing a plant coal and recovered and clean coal fines from the pond. During this study, one plant coal and three blend samples were prepared as 100% plant coal, 90% plant coal/10% fines, 85% plant coal/15% fines, and 80% plant coal /20% fines with a particle size distribution of 70% passing through {minus}200 mesh size. The plant coal and recovered coal fines were obtained from the Randolph Preparation Plant of Peabody Coal Co., Marissa, IL. These samples` combustion behavior will be examined in two different furnaces at Penn State University, i.e., a down-fired furnace and a drop-tube furnace. The down-fired furnace was used mainly to measure the emissions and ash deposition study, while the drop tube furnace was used to determine burning profile, combustion efficiency, etc. The burning profile of the plant coal and the three blends was determined in a thermogravimetric analyzer. Results indicated slower burning of the blends due to low volatile matter and oxidized coal particles. Combustion emissions of these samples were determined in the down-fired combustor, while relative ignition temperatures were determined in the drop tube furnace. Chemical composition of ashes were analyzed to establish a correlation with their respective ash fusion temperatures. Overall study of these samples suggested that the blended samples had combustion properties similar to the original plant coal. In other words, flames were stable under identical firing rates of approximately 200,000 Btu`s/hr and 25% excess air. CO, NO{sub x}, and SO{sub x}, were similar to each other and within the experimental error. Combustion efficiency of 99{sup +}% was achievable. Ash chemical analysis of each sample revealed that slagging and fouling should not be different from each other.

  5. Fractionation and speciation of arsenic in fresh and combusted coal wastes from Yangquan, northern China.

    PubMed

    Gao, Xubo; Wang, Yanxin; Hu, Qinhong

    2012-02-01

    In this study, the content and speciation of arsenic in coal waste and gas condensates from coal waste fires were investigated, respectively, using the digestion and sequential extraction methods. The fresh and fired-coal waste samples were collected from Yangquan, which is one of the major coal production regions in northern China. High-performance liquid chromatography-inductively coupled plasma-mass spectrometry (HPLC-ICP-MS) was used to determine the concentrations of four major arsenic species [As(III), As(V), monomethylarsonic acid (MMA) and dimethylarsenic acid (DMA)] in the extracts, while ICP-MS was used to measure total As content. Arsenic content in the investigated coal wastes and the condensate ranges between 23.3 and 69.3 mg/kg, which are higher than its reported average content in soils. Arsenic in coal waste exists primarily in the residual fraction; this is followed in decreasing order by the organic matter-bound, Fe-Mn oxides-bound, exchangeable, carbonates-bound, and water-soluble fractions. The high content of arsenic in the condensates indicates that combustion or spontaneous combustion is one of the major ways for arsenic release into the environment from coal waste. About 15% of the arsenic in the condensate sample is labile and can release into the environment under leaching processes. The water extractable arsenic (WEA) in the fresh coal waste, fired coal wastes, and the condensate varied between 14.6 and 341 μg/kg, with As(V) as the major species. Furthermore, both MMA and DMA were found in fresh coal wastes, fired coal wastes, and the condensate. PMID:21638002

  6. Assessment of groundwater quality impacts due to use of coal combustion byproducts to control subsidence from underground mines.

    PubMed

    Singh, G; Paul, B C

    2001-06-01

    Coal combustion byproducts are to be placed in an underground coal mine to control subsidence. The materials were characterized to determine potential groundwater impacts. No problems were found with respect to heavy or toxic metals. Coal combustion byproduct leachates are high in dissolved solids and sulfates. Chloride and boron from fly ash may also leach in initially high concentrations. Because the demonstration site is located beneath deep tight brine-bearing aquifers, no problems are anticipated at the demonstration site. PMID:11485225

  7. Numerical modeling of pulverized coal combustion at thermal power plant boilers

    NASA Astrophysics Data System (ADS)

    Askarova, Aliya; Bolegenova, Saltanat; Maximov, Valeryi; Beketayeva, Meruyert; Safarik, Pavel

    2015-06-01

    The paper deals with development and application the numerical model for solution of processes at combustion chamber of the thermal power plant boiler. Mathematical simulation is based on solution of physical and chemical processes occuring at burning pulverized coal in the furnace model. Three-dimensional flows, heat and mass transfer, chemical kinetics of the processes, effects of thermal radiation are considered. Obtained results give quantitative information on velocity distributions, temperature and concentration profiles of the components, the amount of combustion products including harmful substances. The numerical model becomes a tool for investigation and design of combustion chambers with high-efficiency and reliable operation of boiler at thermal power plants.

  8. TRP0033 - PCI Coal Combustion Behavior and Residual Coal Char Carryover in the Blast Furnace of 3 American Steel Companies during Pulverized Coal Injection (PCI) at High Rates

    SciTech Connect

    Veena Sahajwalla; Sushil Gupta

    2005-04-15

    Combustion behavior of pulverized coals (PC), gasification and thermal annealing of cokes were investigated under controlled environments. Physical and chemical properties of PCI, coke and carbon residues of blast furnace dust/sludge samples were characterized. The strong influence of carbon structure and minerals on PCI reactivity was demonstrated. A technique to characterize char carryover in off gas emissions was established.

  9. Combustion characterization of beneficiated coal-based fuels. Quarterly report No. 11, October--December 1991

    SciTech Connect

    Chow, O.K.; Nsakala, N.Y.

    1992-03-01

    The objectives of this project include: (1) the development of an engineering data base which will provide detailed information on the properties of beneficiated coal-based fuels (BCFs) influencing combustion, ash deposition, ash erosion, particulate collection, and emissions; and (2) the application of this technical data base to predict the performance and economic impacts of firing the BCFs in various commercial boiler designs. The technical approach used to develop the technical data includes: bench-scale fuel property, combustion, and ash deposition tests; pilot-scale combustion and ash effects tests; and full-scale combustion tests. Subcontractors perform parts of the test work are the Massachusetts Institute of Technology Physical Science, Inc. Technology Company and the University of North Dakota Energy and Environmental Research Center. Twenty fuels will be characterized during the three-year base program: three feed coals, fifteen BCFs, and two conventionally cleaned coals for full-scale tests. Approximately nine BCFs will be in dry ultra fine coal (DUC) form, and six BCFs will be in coal-water fuel (CWF) form. Additional BCFs would be characterized during optional project supplements. During the third quarter of 1991, the following technical progress was made: Continued analyses of drop tube furnace samples to determine devolatilization kinetics; completed analyses of the samples from the pilot-scale ash deposition tests of three Freeport Pittsburgh 8 fuels; conducted pilot-scale combustion and ash deposition tests of a fresh batch of Upper Freeport parent coal in the CE fireside Performance Test Facility; and completed editing of the fourth quarterly report and sent it to the publishing office.

  10. Strength and corrosion behavior of SiC - based ceramics in hot coal combustion environments

    SciTech Connect

    Breder, K.; Parten, R.J.

    1996-08-01

    As part of an effort to evaluate the use of advanced ceramics in a new generation of coal-fired power plants, four SiC-based ceramics have been exposed to corrosive coal slag in a laboratory furnace and two pilot scale combustors. Initial results indicate that the laboratory experiments are valuable additions to more expensive pilot plant experiments. The results show increased corrosive attack with increased temperature, and that only slight changes in temperature may significantly alter the degree of strength degradation due to corrosive attack. The present results are part of a larger experimental matrix evaluating the behavior of ceramics in the coal combustion environment.

  11. Investigation of the combustion characteristics of Zonguldak bituminous coal using DTA and DTG

    SciTech Connect

    Haykiri-Acma, H.; Yaman, S.; Kucukbayrak, S.; Okutan, H.

    2006-06-21

    Combustion characteristics of coking, semicoking, and noncoking Turkish bituminous coal samples from Zonguldak basin were investigated applying differential thermal analysis (DTA) and differential thermogravimetry (DTG) techniques. Results were compared with that of the coke from Zonguldak bituminous coal, a Turkish lignite sample from Soma, and a Siberian bituminous coal sample. The thermal data from both techniques showed some differences depending on the proximate analyses of the samples. Noncombustible components of the volatile matter led to important changes in thermal behavior. The data front both methods were, evaluated jointly, and some thermal properties were interpreted considering these methods in a complementary combination.

  12. Emission, distribution and toxicity of polycyclic aromatic hydrocarbons (PAHs) during municipal solid waste (MSW) and coal co-combustion.

    PubMed

    Peng, Nana; Li, Yi; Liu, Zhengang; Liu, Tingting; Gai, Chao

    2016-09-15

    Emission and distribution characteristics of polycyclic aromatic hydrocarbons (PAHs) were investigated during municipal solid waste (MSW) and coal combustion alone and MSW/coal blend (MSW weight fraction of 25%) co-combustion within a temperature range of 500°C-900°C. The results showed that for all combustion experiments, flue gas occupied the highest proportion of total PAHs and fly ash contained more high-ring PAHs. Moreover, the 3- and 4-ring PAHs accounted for the majority of total PAHs and Ant or Phe had the highest concentrations. Compared to coal, MSW combustion generated high levels of total PAHs with the range of 111.28μg/g-10,047.22μg/g and had high toxicity equivalent value (TEQ). MSW/coal co-combustion generated the smallest amounts of total PAHs and had the lowest TEQ than MSW and coal combustion alone. Significant synergistic interactions occurred between MSW and coal during co-combustion and the interactions suppressed the formation of PAHs, especially hazardous high-ring PAHs and decreased the TEQ. The present study indicated that the reduction of the yield and toxicity of PAHs can be achieved by co-combustion of MSW and coal. PMID:27265733

  13. Coal Combustion Science quarterly progress report, January--March 1993. Task 1, Coal char combustion: Task 2,, Fate of mineral matter

    SciTech Connect

    Hardesty, D.R.; Hurt, R.H.; Baxter, L.L.

    1994-02-01

    The objective of this work is to obtain insights into the mechanisms of combustion, fragmentation, and final burnout, and to use the insights to aid in the interpretation of the quantitative data generated in Subtasks 1 and 2. The initial image sequences for Illinois No. 6 coal confirm the presence of an early near-extinction process (discussed in previous reports) and the asymptotic nature of the carbon burnout process. The technique also provided important new insights into the processes of particle fragmentation and reagglomeration at high burnout. During this quarter, chemical fractionation tests on coals pulverized to different sizes were completed. These data will help us to asses the accuracy of the fuels characterizations for the purpose of interpreting inorganic release during coal devolatilization. Chemical fractionation tests on mineral species are proceeding for the same purposes, but these are not yet completed.

  14. Residual carbon from pulverized coal fired boilers 1: Size distribution and combustion reactivity

    SciTech Connect

    Hurt, R.H.; Gibbins, J.R.

    1994-08-01

    The amount of residual, or unburned, carbon in fly ash is an important concern in the design and operation of pulverized coal-fired boilers. Char oxidation is the slowest step in the coal combustion process, and the rate at which this heterogeneous reaction-proceeds has an important effect on the degree of carbon burnout. There is an extensive literature on char combustion kinetics based on data in the early and intermediate stages of carbon conversion. A critical fundamental question is whether the small fraction of the fuel carbon that passes unreacted through a boiler is representative of the char during the main portion of the combustion process. This article addresses that question through a detailed characterization of eight carbon-containing fly ash samples acquired from commercial-scale combustion systems. The fly ash characterization included measurement-of joint carbon/size distribution and determination.of the combustion reactivity of the residual carbon. To minimize mineral matter interactions in the reactivity tests, the technique of incipient fluidization was developed for separation of carbon-rich extracts from the inorganic portion of the fly ash. Reactivity measurements were made at 1400--1800 K to represent conditions in pulverized coal fired boilers. Measurements were also made at 700--1100 K to. minimize transport effects and isolate the influence of char chemistry and microstructure. In both temperature regimes, the residual carbon extracts. were significantly less reactive than chars extracted from a laboratory-scale laminar flow reactor in the early-to-intermediate stages of combustion. It is concluded that the boiler environment deactivates chars, making high carbon burnout more difficult to achieve than is predicted by existing char combustion kinetic models that were developed from data on the laboratory chars. Finally, the results are used to discuss potential char deactivation mechanisms, both thermal and oxidative, in coal-fired boilers.

  15. SPONCOM - a computer program for the prediction of the spontaneous combustion potential of an underground coal mine

    SciTech Connect

    Smith, A.C.; Rumancik, W.P.; Lazzara, C.P.

    1996-12-31

    The United States Bureau of Mines (USBM) developed SPONCOM to aid in the assessment of the spontaneous combustion risk of an underground mining operation. A prior knowledge of the spontaneous combustion risk of the coal and factors that increase that risk can be useful in the planning and development of proactive monitoring, ventilation, and prevention plans for the mining operation. Interactive data input screens prompt the user for information about the coal`s chemical and physical properties, the geologic and mining conditions encountered in the mining of the coal, and the mining practices employed. During the input process, {open_quote}expand{close_quote} screens provide the user with specific information on each input parameter. This information includes a description of the parameter and its effect on the overall spontaneous combustion risk. The program logic determines the coal`s relative spontaneous combustion potential, based on the coal`s proximate and ultimate analyses, and heating value. The program then evaluates the impact of the coal properties, geologic and mining conditions, and mining practices on the spontaneous combustion risk of the mining operation. The program output provides details on each factor that increases the risk of spontaneous combustion.

  16. Eocene-Miocene carbon-isotope and floral record from brown coal seams in the Gippsland Basin of southeast Australia

    NASA Astrophysics Data System (ADS)

    Holdgate, Guy R.; McGowran, Brian; Fromhold, Tom; Wagstaff, Barbara E.; Gallagher, Stephen J.; Wallace, Malcolm W.; Sluiter, Ian R. K.; Whitelaw, Michael

    2009-01-01

    The carbon-isotope and palynological record through 580 m thick almost continuous brown coal in southeast Australia's Gippsland Basin is a relatively comprehensive southern hemisphere Middle Eocene to Middle Miocene record for terrestrial change. The carbon isotope δ 13C coal values of these coals range from - 27.7‰ to - 23.2. This isotopic variability follows gymnosperm/angiosperm fluctuations, where higher ratios coincide with heavier δ13C values. There is also long-term variability in carbon isotopes through time. From the Eocene greenhouse world of high gymnosperm-heavier δ13C coal values, there is a progressive shift to lighter δ13C coal values that follows the earliest (Oi1?) glacial events around 33 Ma (Early Oligocene). The overlying Oligocene-Early Miocene brown coals have lower gymnosperm abundance, associated with increased % Nothofagus (angiosperm), and lightening of isotopes during Oligocene cooler conditions. The Miocene palynological and carbon-isotope record supports a continuation to the Oligocene trends until around the late Early Miocene (circa 19 Ma) when a warming commenced, followed by an even stronger isotope shift around 16 Ma that peaked in the Middle Miocene when higher gymnosperm abundance and heavier isotopes prevailed. The cycle between the two major warm peaks of Middle Eocene and Middle Miocene was circa 30 Ma long. This change corresponds to a fall in inferred pCO 2 levels for the same period. The Gippsland data suggest a link between gymnosperm abundance, long-term plant δ13C composition, climatic change, and atmospheric pCO 2. Climatic deterioration in the Late Miocene terminated peat accumulation in the Gippsland Basin and no further significant coals formed in southeast Australia. The poor correspondence between this terrestrial isotope data and the marine isotope record is explained by the dominant control on δ13C by the gymnosperm/angiosperm abundance, although in turn this poor correspondence may reflect palaeoclimate

  17. Application of rubber anti-aging agents in preventing coal spontaneous combustion

    SciTech Connect

    Yu, S.; Zhang, R.; Yang, Y.; Yang, H.; Fan, X.

    1999-07-01

    Based on the mechanism of rubber aging and action of anti-aging agents in preventing rubber aging, the free radical chain reaction mechanism of the oxidation of coal was discussed and compound stopping agents were introduced in the paper. The rubber anti-aging agents of aromatic amine are selected for the stopping agent of preventing coal spontaneous combustion. The stopping action of these anti-aging agents and common inorganic salt stopping agents for long flame coal in Gengcun Colliery, Yima city, Henan province in China is researched. The anti-aging agents for the long flame coal have the prominent efficiency and fine stopping action in later period, and inorganic stopping agents containing magnesium chloride salt for the long flame coal have the prominent efficiency in early period, but the compound stopping agents that are composed of the rubber anti-aging agents and magnesium chloride have longer life.

  18. Occurrence and transformation of phyllocladanes in brown coals from Nograd Basin, Hungary

    NASA Astrophysics Data System (ADS)

    Alexander, Gabor; Hazai, Istvan; Grimalt, Joan; Albaigés, Joan

    1987-08-01

    Phyllodactanes are the major components of the lipid extracts of two series of brown coals from the Nograd Basin (Northern Hungary). In this basin coalification was induced by thermal stress of volcanic origin which determined the isomeric composition of these compounds. Depending on the degree of maturation the 16α(H)-isomer decreases in abundance relative to the more geochemically stable 16β(H)-isomer, the presumed equilibrium ratio being 0.3. Laboratory thermal degradation experiments have confirmed the feasibility of this transformation, showing that phyllocladene and isophyllocladene are intermediate products of the process. Variable amounts of retene and simonellite are also found, but no evidence is obtained of abietane-type precursors. Nevertheless, a close relationship of the retene-phyllocladane ratio with maturity, represented by the H/C ratio, is observed. As an explanation, it is suggested the thermally induced formation of retene from phyllocladanes, simonellite being an intermediate of the proposed reaction. Further evidence for this hypothesis has been obtained from laboratory simulation experiments. Finally, the presumed isomerization and aromatization rates of these diterpenoids have been compared for the series of samples, pointing to a promising tool for assessing the geochemical history of coal basins.

  19. The influence of thermal annealing on oxygen uptake and combustion rates of a bituminous coal char

    SciTech Connect

    Osvalda Senneca; Piero Salatino; Daniela Menghini

    2007-07-01

    The effect of thermal annealing on the combustion reactivity of a bituminous coal char has been investigated with a focus on the role of the formation of surface oxides by oxygen chemisorption. The combined use of thermogravimetric analysis and of analysis of the off-gas during isothermal combustion of char samples enabled the determination of the rate and extent of oxygen uptake along burn-off. Combustion was carried out at temperatures between 350 and 510{sup o}C. Char samples were prepared by controlled isothermal heat treatment of coal for different times (in the range between 1 s and 30 min) at different temperatures (in the range 900-2000{sup o}C). Results indicate that oxygen uptake is extensive along burn-off of chars prepared under mild heat treatment conditions. The maximum oxygen uptake is barely affected by the combustion temperature within the range of combustion conditions investigated. The severity of heat treatment has a pronounced effect on char combustion rate as well as on the extent and rate at which surface oxides are built up by oxygen chemisorption. Chars prepared under severe heat treatment conditions show negligible oxygen uptake and strongly reduced combustion rates. Altogether it appears that a close correlation can be established between the extent and the accessibility of active sites on the carbon surface and the combustion rate. Despite the investigation has been carried out at temperatures well below those of practical interest, results provide useful insight into the relationship existing between thermal annealing, formation of surface oxide and combustion reactivity which is relevant to the proper formulation of detailed kinetic models of char combustion. 31 refs., 6 figs., 1 tab.

  20. SPECIATION OF MERCURY IN THE PRESENCE OF COAL AND WASTE COMBUSTION FLY ASHES

    EPA Science Inventory

    The paper gives results of a study that focused on the oxidation of elemental mercury (Hgo) in the presence of both complex, four-component, model fly ashes, and actual coal combustion fly ashes collected from a pilot plant. Steady-state oxidation of Hgo promoted by the four-com...

  1. XAFS SPECTROSCOPY ANALYSIS OF SELECTED HAP ELEMENTS IN FINE PM DERIVED FROM COAL COMBUSTION

    EPA Science Inventory

    X-ray absorption fine structure (XAFS) spectroscopy has been used to investigate the valence states and molecular structures of sulfur (S), chromium (Cr), arsenic (As), and zinc (Zn) in fine particulate matter (PM) separated from coal flyash produced in a realistic combustion sys...

  2. CERAMIC FILTER TESTS AT THE EPA/EXXON PFBC (PRESSURIZED FLUIDIZED BED COAL COMBUSTION) MINIPLANT

    EPA Science Inventory

    The paper describes the performance of the Acurex ceramic bag filter operating at temperatures up to 880C and pressures up to 930 kPa on particulate-laden flue gas from a pressurized fluidized-bed coal combustion (PFBC) unit on a slipstream of gas taken after the second stage cyc...

  3. PRELIMINARY ENVIRONMENTAL ASSESSMENT OF COAL-FIRED FLUIDIZED-BED COMBUSTION SYSTEMS

    EPA Science Inventory

    The report evaluates potential pollutants which could be generated in coal-fired fluidized-bed combustion (FBC) processes. The primary emphasis is on organic compounds, trace elements, inorganic compounds (other than SO2 and Nox), and particulates. Using available bench scale or ...

  4. CONTROL OF CRITERIA AND NON-CRITERIA POLLUTANTS FROM COAL/LIQUID MIXTURE COMBUSTION

    EPA Science Inventory

    The report summarizes the existing data base on NOx, SO2, and particulate matter emissions from combustion sources burning coal/liquid mixtures (CLMs). It also gives available emissions data for the various trace elements, and identifies control techniques that can reduce the emi...

  5. ENVIRONMENTAL ASSESSMENT OF THE FLUIDIZED-BED COMBUSTION OF COAL: METHODOLOGY AND INITIAL RESULTS

    EPA Science Inventory

    The paper discusses a program being conducted by the U.S. Environmental Protection Agency (EPA), aimed at complete environmental assessment (EA) of the fluidized-bed combustion (FBC) of coal. It reviews the EA methodology being developed by EPA: identification of current technolo...

  6. Materials performance in coal-fired fluidized-bed combustion environments

    SciTech Connect

    Natesan, K.

    1993-07-01

    Development of cogeneration systems that involve combustion of coal in a fluidized bed for the generation of electricity and process heat has been in progress for a number of years. This paper addresses some of the key components in these systems, materials requirements/performance, and areas where additional effort is needed to improve the viability of these concepts for electric power generation.

  7. Management of high sulfur coal combustion residues, issues and practices: Proceedings

    SciTech Connect

    Chugh, Y.P.; Beasley, G.A.

    1994-10-01

    Papers presented at the following sessions are included in this proceedings: (1) overview topic; (2) characterization of coal combustion residues; (3) environmental impacts of residues management; (4) materials handling and utilization, Part I; and (5) materials handling and utilization, Part II. Selected paper have been processed separately for inclusion in the Energy Science and Technology Database.

  8. COMBUSTION MODIFICATION NOX CONTROLS FOR UTILITY BOILERS. VOLUME I: TANGENTIAL COAL-FIRED UNIT FIELD TEST

    EPA Science Inventory

    The report gives results of an environmental assessment field testing program on a tangential-coal-fired utility boiler. The aim of the program was to measure multimedia emissions changes as a result of applying combustion modification NOx control. Emissions of trace elements, or...

  9. Study of boron behaviour in two Spanish coal combustion power plants.

    PubMed

    Ochoa-González, Raquel; Cuesta, Aida Fuente; Córdoba, Patricia; Díaz-Somoano, Mercedes; Font, Oriol; López-Antón, M Antonia; Querol, Xavier; Martínez-Tarazona, M Rosa; Giménez, Antonio

    2011-10-01

    A full-scale field study was carried out at two Spanish coal-fired power plants equipped with electrostatic precipitator (ESP) and wet flue gas desulfurisation (FGD) systems to investigate the distribution of boron in coals, solid by-products, wastewater streams and flue gases. The results were obtained from the simultaneous sampling of solid, liquid and gaseous streams and their subsequent analysis in two different laboratories for purposes of comparison. Although the final aim of this study was to evaluate the partitioning of boron in a (co-)combustion power plant, special attention was paid to the analytical procedure for boron determination. A sample preparation procedure was optimised for coal and combustion by-products to overcome some specific shortcomings of the currently used acid digestion methods. In addition boron mass balances and removal efficiencies in ESP and FGD devices were calculated. Mass balance closures between 83 and 149% were obtained. During coal combustion, 95% of the incoming boron was collected in the fly ashes. The use of petroleum coke as co-combustible produced a decrease in the removal efficiency of the ESP (87%). Nevertheless, more than 90% of the remaining gaseous boron was eliminated via the FGD in the wastewater discharged from the scrubber, thereby causing environmental problems. PMID:21664037

  10. WASTE AND WATER MANAGEMENT FOR CONVENTIONAL COAL COMBUSTION ASSESSMENT REPORT - 1979; VOLUME II. WATER MANAGEMENT

    EPA Science Inventory

    The report, the second of five volumes, describes water management for conventional combustion sources and assesses the current status of various studies and programs in water management and trends in water recycle/reuse. A coal-fired boiler produces both chemical and thermal pol...

  11. THE USE OF A PRB TO TREAT GROUNDWATER IMPACTED BY COAL-COMBUSTION BY-PRODUCTS

    EPA Science Inventory

    The burning of coal for the production of electricity generates combustion by-products such as boiler bottom ash and fly ash. These ashes have the potential to release arsenic (As), boron (B), chromium (Cr), molybdenum (Mo), selenium (Se), vanadium (V), and zinc (Zn) to the envi...

  12. XFAS SPECTROSCOPY ANALYSIS OF SELECTED HAP ELEMENTS IN FINE PM DERIVED FROM COAL COMBUSTION: JOURNAL ARTICLE

    EPA Science Inventory

    NRMRL-RTP-P-646 Shoji, T., Huggins, F.E., Huffman, G.P., Linak*, W.P., and Miller*, C.A. XFAS Spectroscopy Analysis of Selected HAP Elements in Fine PM Derived from Coal Combustion. Energy and Fuels 16 (2): (2002). 11/30/2001 X-ray absorption fine structure (XAFS) spectroscop...

  13. Land application of coal combustion by-products: Use in agriculture and land reclamation. Final report

    SciTech Connect

    Horn, M.E.

    1995-06-01

    Land application of coal combustion by-products (CCBP) can prove beneficial for a number of reasons. The data presented in this survey provide a basis for optimizing the rates and timing of CCBP applications, selecting proper target soils and crops, and minimizing adverse effects on soil properties, plant responses, and groundwater quality.

  14. Coal slurry combustion optimization on single cylinder engine. Task 1.1.2.2.2, Combustion R&D

    SciTech Connect

    Not Available

    1992-09-01

    Under the sponsorship of the US Department of Energy, Morgantown Energy Technology Center, GE Transportation System has been conducting a proof of concept program to use coal water slurry (CWS) fuel to power a diesel engine locomotive since 1988. As reported earlier [1], a high pressure electronically controlled accumulator injector using a diamond compact insert nozzle was developed for this project. The improved reliability and durability of this new FIE allowed for an improved and more thorough study of combustion of CWS fuel in a diesel engine. It was decided to include a diesel pilot fuel injector in the combustion system mainly due to engine start and low load operation needs. BKM, Inc. of San Diego, CA was contracted to develop the electronic diesel fuel pilot/starting FIE for the research engine. As a result, the experimental combustion study was very much facilitated due to the ability of changing pilot/CWS injection timings and quantities without having to stop the engine. Other parameters studied included combustion chamber configuration (by changing CWS fuel injector nozzle hole number/shape/angle), as well as injection pressure. The initial phase of this combustion study is now complete. The results have been adopted into the design of a 12 cylinder engine FIE, to be tested in 1992. This paper summarizes the main findings of this study.

  15. Comparison of chars obtained under oxy-fuel and conventional pulverized coal combustion atmospheres

    SciTech Connect

    Angeles G. Borrego; Diego Alvarez

    2007-12-15

    In this study, two coals of different rank (a high volatile and a low volatile bituminous) have been burned in a drop tube reactor using O{sub 2}/N{sub 2} and O{sub 2}/CO{sub 2} mixtures with increasing oxygen content from 0 to 21%. Various oxygen concentrations have been selected for each set of experiments in order to follow both the progress of combustion and the influence of oxygen content in the devolatilization behavior of coal. Results show that a higher amount of O{sub 2} in CO{sub 2} than in N{sub 2} is needed to achieve similar burnout levels. Significant differences were found in the influence of oxygen content on the devolatilization behavior of the lower and higher rank coal. The limited amount of oxygen in the reacting atmosphere resulted in volatile release inhibition for the high volatile bituminous coal, whereas the more plastic low volatile coal was hardly affected. The presence of variable amounts of oxygen in CO{sub 2} had a small influence on the char particle appearance. The chars from both the combustion series (O{sub 2}/N{sub 2}) and the oxy-fuel series (O{sub 2}/CO{sub 2}) were similar for each parent coal in terms of reactivity and micropore surface area measured by CO{sub 2} adsorption. The main difference between both series of chars relied on the surface area determined by N{sub 2} adsorption (SBET) and on the size distribution of pores which was shifted to a larger size for the oxy-fuel series. The difference between both series of chars was larger for the high volatile bituminous coal chars than for the low volatile bituminous coal chars. This might have important implications for combustion under the diffusion-controlled regime. 29 refs., 13 figs., 1 tab.

  16. Investigation of mechanisms of ash deposit formation from low-rank coal combustion: Final report

    SciTech Connect

    Greene, F.T.; O'Donnell, J.E.

    1987-08-01

    This project was undertaken to determine the chemical behavior of alkali metal and other species implicated in the ash fouling which can occur during the combustion of low rank coals. The coal combustion was studied in unaugmented premixed pulverized coal flames. Vapor species were measured by molecular beam mass spectrometry. Temperatures were also measured, and time-resolved coal/ash particulate samples were collected and analyzed. A major part of the research on this project was devoted to: (1) the development and refinement of techniques for the MBMS analysis of trace quantities of unstable and reactive high temperature vapor species from the pulverized coal flames; and (2) the time-resolved sampling and collection of particulates. The equipment is now operating very satisfactorily. Inorganic species, some of which were present at parts-per-million levels, were quantitatively sampled and measured in the pulverized coal flames. Time-resolved particulate samples which were free of vapor deposited contaminants were collected without the use of an interfering substrate. Profiles of the alkali metal species in Beulah lignite and Decker subbituminous coal flames were obtained. It was found in both flames that sodium is volatilized as the atomic species early (milliseconds) in the combustion process. The gaseous Na reacts, also in milliseconds, to form an unknown species which is probably an oxide fume, but which is not NaOH or Na/sub 2/SO/sub 4/. This is probably the mechanism for the formation of the alkali ''fumes'' observed in other systems. Measurements were also made of a number of other gaseous species, and time-resolved coal/ash samples were obtained and analyzed. 27 refs., 23 figs., 8 tabs.

  17. Recent advances in large-eddy simulation of spray and coal combustion

    NASA Astrophysics Data System (ADS)

    Zhou, L. X.

    2013-07-01

    Large-eddy simulation (LES) is under its rapid development and is recognized as a possible second generation of CFD methods used in engineering. Spray and coal combustion is widely used in power, transportation, chemical and metallurgical, iron and steel making, aeronautical and astronautical engineering, hence LES of spray and coal two-phase combustion is particularly important for engineering application. LES of two-phase combustion attracts more and more attention; since it can give the detailed instantaneous flow and flame structures and more exact statistical results than those given by the Reynolds averaged modeling (RANS modeling). One of the key problems in LES is to develop sub-grid scale (SGS) models, including SGS stress models and combustion models. Different investigators proposed or adopted various SGS models. In this paper the present author attempts to review the advances in studies on LES of spray and coal combustion, including the studies done by the present author and his colleagues. Different SGS models adopted by different investigators are described, some of their main results are summarized, and finally some research needs are discussed.

  18. Characteristics of carbonized sludge for co-combustion in pulverized coal power plants

    SciTech Connect

    Park, Sang-Woo; Jang, Cheol-Hyeon

    2011-03-15

    Co-combustion of sewage sludge can destabilize its combustion profile due to high volatility, which results in unstable flame. We carried out fuel reforming for sewage sludge by way of carbonization at pyrolysis temperature of 300-500 deg. C. Fuel characteristics of carbonized sludge at each temperature were analyzed. As carbonization temperature increased, fuel ratio increased, volatile content reduced, and atomic ratio relation of H/C and O/C was similar to that of lignite. The analysis result of FT-IR showed the decrease of aliphatic C-H bond and O-C bond in carbonization. In the analysis result of TG-DTG, the thermogravimetry reduction temperature of carbonized sludge (CS400) was proven to be higher than that of dried sludge, but lower than that of sub-bituminous coal. Hardgrove grindability index increased in proportion to fuel ratio increase, where the carbonized sludge value of 43-110 was similar or higher than the coal value of 49-63. As for ash deposits, slagging and fouling index were higher than that of coal. When carbonized sludge (CS400) and coal were co-combusted in 1-10% according to calorific value, slagging tendency was low in all conditions, and fouling tendency was medium or high according to the compositions of coal.

  19. Capture of toxic metals by vaious sorbents during fluidized bed coal combustion

    SciTech Connect

    Ho, T.C.; Ghebremeskel, A.; Hopper, J.R.

    1995-12-31

    This study investigated the potential of employing suitable sorbents to capture trace metallic substances during fluidized bed coal combustion. The objectives of the study were to demonstrate the capture process, identify effective sorbents, and characterize the capture efficiency. Experiments were carried out in a 25.4 mm (1 ``) quartz fluidized bed coal combustor enclosed in an electric furnace. In an experiment, a coal sample from the DOE Coal Sample Bank or the Illinois Basin Coal Sample Bank was burned in the bed with a sorbent under various combustion conditions and the amount of metal capture by the sorbent was determined. The metals involved in the study were arsenic, cadmium, lead, mercury and selenium, and the sorbents tested included bauxite, zeolite and lime. The combustion conditions examined included bed temperature, particle size, fluidization velocity (percent excess air), and sorbent bed height. In addition to the experimental investigations, potential metal-sorbent reactions were also identified through performing chemical equilibrium analyses based on the minimization of system free energy.

  20. Mineralogical characterization of ambient fine/ultrafine particles emitted from Xuanwei C1 coal combustion

    NASA Astrophysics Data System (ADS)

    Lu, Senlin; Hao, Xiaojie; Liu, Dingyu; Wang, Qiangxiang; Zhang, Wenchao; Liu, Pinwei; Zhang, Rongci; Yu, Shang; Pan, Ruiqi; Wu, Minghong; Yonemochi, Shinich; Wang, Qingyue

    2016-03-01

    Nano-quartz in Xuanwei coal, the uppermost Permian (C1) coal deposited in the northwest of Yuanan, China, has been regarded as one of factors which caused high lung cancer incidence in the local residents. However, mineralogical characterization of the fine/ultrafine particles emitted from Xuanwei coal combustion has not previously been studied. In this study, PM1 and ultrafine particles emitted from Xuanwei coal combustion were sampled. Chemical elements in the ambient particles were analyzed by inductively coupled plasma mass spectrometry (ICP-MS), and mineralogical characterization of these ambient particles was investigated using scanning electronic microscopy (SEM/EDX) and transmission electronic microscopy, coupled with energy-dispersive spectroscopy (TEM/EDX). Our results showed that the size distribution of mineral particles from the coal combustion emissions ranged from 20 to 200 nm. Si-containing particles and Fe-containing particles accounted for 50.7% of the 150 individual particles measured, suggesting that these two types of particles were major minerals in the ambient particles generally. The nano-mineral particles were identified as quartz (SiO2) and gypsum (CaSO4) based on their crystal parameters and chemical elements. Additionally, there also existed unidentified nano-minerals. Armed with these data, toxicity assessments of the nano-minerals will be carried out in a future study.

  1. [Predicting low NOx combustion property of a coal-fired boiler].

    PubMed

    Zhou, Hao; Mao, Jianbo; Chi, Zuohe; Jiang, Xiao; Wang, Zhenhua; Cen, Kefa

    2002-03-01

    More attention was paid to the low NOx combustion property of the high capacity tangential firing boiler, but the NOx emission and unburned carbon content in fly ash of coal burned boiler were complicated, they were affected by many factors, such as coal character, boiler's load, air distribution, boiler style, burner style, furnace temperature, excess air ratio, pulverized coal fineness and the uniformity of the air and coal distribution, etc. In this paper, the NOx emission property and unburned carbon content in fly ash of a 600 MW utility tangentially firing coal burned boiler was experimentally investigated, and taking advantage of the nonlinear dynamics characteristics and self-learning characteristics of artificial neural network, an artificial neural network model on low NOx combustion property of the high capacity boiler was developed and verified. The results illustrated that such a model can predicate the NOx emission concentration and unburned carbon content under various operating conditions, if combined with the optimization algorithm, the operator can find the best operation condition of the low NOx combustion. PMID:12048812

  2. CHARACTERIZATION OF COAL COMBUSTION BY-PRODUCTS FOR THE RE-EVOLUTION OF MERCURY INTO ECOSYSTEMS

    SciTech Connect

    A.M. Schwalb; J.A. Withum; R.M. Statnick

    2002-07-01

    The U.S. Environmental Protection Agency (EPA) and state environmental agencies are suggesting that mercury (Hg) in coal combustion by-products is re-emitted into local ecosystems by additional processing to final products (i.e., wallboard, etc.), by dissolution into groundwater, or by reactions with anaerobic bacteria. This perception may limit the opportunities to use coal combustion by-products in recycle/reuse applications. In this program, CONSOL Energy Inc., Research & Development (CONSOL) is conducting a comprehensive sampling and analytical program to address this concern. If the results of this work demonstrate that re-emissions of Hg from waste disposal and by-product utilization are over-stated, additional regulations regarding coal combustion, waste disposal, and waste material utilization will not be required. This will result in continued low energy cost that is beneficial to the national economy and stability of local economies that are dependent on coal. The main activities for this quarter were: fly ash and FGD slurry samples from four coal-fired utilities were leached and the analysis was completed; the re-volatilization study has begun; the literature review was completed.

  3. Performance of a high efficiency advanced coal combustor. Task 2, Pilot scale combustion tests: Final report

    SciTech Connect

    Toqan, M.A.; Paloposki, T.; Yu, T.; Teare, J.D.; Beer, J.M.

    1989-12-01

    Under contract from DOE-PETC, Combustion Engineering, Inc. undertook the lead-role in a multi-task R&D program aimed at development of a new burner system for coal-based fuels; the goal was that this burner system should be capable of being retrofitted in oil- or gas-fired industrial boilers, or usable in new units. In the first phase of this program a high efficiency advanced coal combustor was designed jointly by CE and MIT. Its burner is of the multiannular design with a fixed shrouded swirler in the center immediately surrounding the atomizer gun to provide the ``primary act,`` and three further annuli for the supply of the ``secondary air.`` The degree of rotation (swirl) in the secondary air is variable. The split of the combustion air into primary and secondary air flows serves the purpose of flame stabilization and combustion staging, the latter to reduce NO{sub x} formation.

  4. Development and testing of commercial-scale, coal-fired combustion systems: Phase 3

    SciTech Connect

    Not Available

    1992-01-01

    The US Department of Energy's Pittsburgh Energy Technology Center (PETC) is actively pursuing the development and testing of coal-fired combustion systems for residential, commercial, and industrial market sectors. In response, MTCI initiated the development of a new combustor technology based on the principle of pulse combustion under the sponsorship of PETC (Contract No. AC22-83PC60419). The initial pulse combustor development program was conducted in three phases (MTCI, Development of a Pulsed Coal Combustor Fired with CWM, Phase III Final Report, DOE Contract No. AC22-83PC60419, November 1986). Phase I included a review of the prior art in the area of pulse combustion and the development of pulse combustor design concepts. It led to the conclusion that pulse combustors offer technical and base-of-operation advantages over conventional burners and also indicated favorable economics for replacement of oil- and gas-fired equipment.

  5. Performance and mechanism on a high durable silica alumina based cementitious material composed of coal refuse and coal combustion byproducts

    NASA Astrophysics Data System (ADS)

    Yao, Yuan

    Coal refuse and combustion byproducts as industrial solid waste stockpiles have become great threats to the environment. Recycling is one practical solution to utilize this huge amount of solid waste through activation as substitute for ordinary Portland cement. The central goal of this dissertation is to investigate and develop a new silica-alumina based cementitious material largely using coal refuse as a constituent that will be ideal for durable construction, mine backfill, mine sealing and waste disposal stabilization applications. This new material is an environment-friendly alternative to ordinary Portland cement. The main constituents of the new material are coal refuse and other coal wastes including coal sludge and coal combustion products (CCPs). Compared with conventional cement production, successful development of this new technology could potentially save energy and reduce greenhouse gas emissions, recycle vast amount of coal wastes, and significantly reduce production cost. A systematic research has been conducted to seek for an optimal solution for enhancing pozzolanic reactivity of the relatively inert solid waste-coal refuse in order to improve the utilization efficiency and economy benefit for construction and building materials. The results show that thermal activation temperature ranging from 20°C to 950°C significantly increases the workability and pozzolanic property of the coal refuse. The optimal activation condition is between 700°C to 800°C within a period of 30 to 60 minutes. Microanalysis illustrates that the improved pozzolanic reactivity contributes to the generated amorphous materials from parts of inert aluminosilicate minerals by destroying the crystallize structure during the thermal activation. In the coal refuse, kaolinite begins to transfer into metakaol in at 550°C, the chlorite minerals disappear at 750°C, and muscovite 2M1 gradually dehydroxylates to muscovite HT. Furthermore, this research examines the environmental

  6. Pilot Testing of WRI'S Novel Mercury Control Technology by Pre-Combustion Thermal Treatment of Coal

    SciTech Connect

    Alan Bland; Jesse Newcomer; Kumar Sellakumar

    2008-08-17

    The challenges to the coal-fired power industry continue to focus on the emission control technologies, such as mercury, and plant efficiency improvements. An alternate approach to post-combustion control of mercury, while improving plant efficiency deals with Western Research Institute's (WRI)'s patented pre-combustion mercury removal and coal upgrading technology. WRI was awarded under the DOE's Phase III Mercury program, to evaluate the effectiveness of WRI's novel thermal pretreatment process to achieve >50% mercury removal, and at costs of <$30,000/lb of Hg removed. WRI has teamed with Etaa Energy, Energy and Environmental Research Center (EERC), Foster Wheeler North America Corp. (FWNA), and Washington Division of URS (WD-URS), and with project co-sponsors including Electric Power Research Institute (EPRI), Southern Company, Basin Electric Power Cooperative (BEPC), Montana-Dakota Utilities (MDU), North Dakota Industrial Commission (NDIC), Detroit Edison (DTE), and SaskPower to undertake this evaluation. The technical objectives of the project were structured in two phases: Phase I--coal selection and characterization, and bench-and PDU-scale WRI process testing and; and Phase II--pilot-scale pc combustion testing, design of an integrated boiler commercial configuration, its impacts on the boiler performance and the economics of the technology related to market applications. This report covers the results of the Phase I testing. The conclusion of the Phase I testing was that the WRI process is a technically viable technology for (1) removing essentially all of the moisture from low rank coals, thereby raising the heating value of the coal by about 30% for subbituminous coals and up to 40% for lignite coals, and (2) for removing volatile trace mercury species (up to 89%) from the coal prior to combustion. The results established that the process meets the goals of DOE of removing <50% of the mercury from the coals by pre-combustion methods. As such, further

  7. Coal combustion: Effect of process conditions on char reactivity. Final technical report, September 1, 1991--May 31, 1995

    SciTech Connect

    Zygourakis, K.

    1996-02-01

    Coal utilization involves two major stages: coal pyrolysis and char combustion. Figure 1.1 summarizes the steps of these processes. During the pyrolysis stage, heated particles from plastic coals soften, swell and release their volatiles before resolidifying again. During the combustion or gasification stage, char particles may ignite and fragment as the carbon is consumed leaving behind a solid ash residue. Process conditions such as pyrolysis heating rate, heat treatment temperature, pyrolysis atmosphere, and particle size are shown to chemically and physically affect the coal during pyrolysis and the resulting char. Consequently, these pyrolysis conditions as well as the combustion conditions such as the oxygen concentration and combustion temperature affect the char reactivity and ignition phenomena during the combustion stage. Better understanding of the fundamental mechanisms of coal pyrolysis and char combustion is needed to achieve greater and more efficient utilization of coal. Furthermore, this knowledge also contributes to the development of more accurate models that describe the transient processes involved in coal combustion. The project objectives were to investigate the effect of pyrolysis conditions on the macropore structure and subsequent reactivity of chars.

  8. Combustion of dense streams of coal particles. Final report, August 29, 1990--February 28, 1994

    SciTech Connect

    Annamalai, K.; Gopalakrishnan, C.; Du, X.

    1994-05-01

    The USA consumes almost 94 quads of energy (1 quad = 10{sup 15} BTU or 1.05 {times} 10{sup 15} KJ). The utilities account for about 30 quads of fossil energy where coal is predominantly used as energy source. The coal is ground to finer size and fired into the boiler as dense suspension. Under dense conditions, the particles burn at slower rate due to deficient oxygen within the interparticle spacing. Thus interactions exist amongst the particles for dense clouds. While the earlier literature dealt with combustion processes of isolated particles, the recent research focusses upon the interactive combustion. The interactive combustion studies include arrays consisting of a finite number of particles, and streams and clouds of a large number of particles. Particularly stream combustion models assume cylindrical geometry and predict the ignition and combustion characteristics. The models show that the ignition starts homogeneously for dense streams of coal particles and the ignition time show a minimum as the stream denseness is increased, and during combustion, there appears to be an inner flame within the stream and an outer flame outside the stream for a short period of time. The present experimental investigation is an attempt to verify the model predictions. The set-up consists of a flat flame burner for producing hot vitiated gases, a locally fluidizing feeder system for feeding coal particles, a particle collection probe for collecting particles and an image processing system for analyzing the flame structure. The particles are introduced as a stream into the hot gases and subsequently they ignite and burn. The ash % of fired and collected particles are determined and used to estimate the gasification efficiency or burnt fraction. The parametric studies include gas temperature, oxygen % in gases, residence time, and A:F ratio of the stream.

  9. Chemical-looping combustion of coal with metal oxide oxygen carriers

    SciTech Connect

    Ranjani Siriwardane; Hanjing Tian; George Richards; Thomas Simonyi; James Poston

    2009-08-15

    The combustion and reoxidation properties of direct coal chemical-looping combustion (CLC) over CuO, Fe{sub 2}O{sub 3}, CO{sub 3}O{sub 4}, NiO, and Mn{sub 2}O{sub 3} were investigated using thermogravimetric analysis (TGA) and bench-scale fixed-bed flow reactor studies. When coal is heated in either nitrogen or carbon dioxide (CO{sub 2}), 50% of weight loss was observed because of partial pyrolysis, consistent with the proximate analysis. Among various metal oxides evaluated, CuO showed the best reaction properties: CuO can initiate the reduction reaction as low as 500{sup o}C and complete the full combustion at 700{sup o}C. In addition, the reduced copper can be fully reoxidized by air at 700{sup o}C. The combustion products formed during the CLC reaction of the coal/metal oxide mixture are CO{sub 2} and water, while no carbon monoxide was observed. Multicycle TGA tests and bench-scale fixed-bed flow reactor tests strongly supported the feasibility of CLC of coal by using CuO as an oxygen carrier. Scanning electron microscopy (SEM) images of solid reaction products indicated some changes in the surface morphology of a CuO-coal sample after reduction/oxidation reactions at 800 {sup o}C. However, significant surface sintering was not observed. The interactions of fly ash with metal oxides were investigated by X-ray diffraction and thermodynamic analysis. Overall, the results indicated that it is feasible to develop CLC with coal by metal oxides as oxygen carriers. 22 refs., 12 figs., 2 tabs.

  10. Combustion of coal/water mixtures with thermal preconditioning. Final report

    SciTech Connect

    Novack, M.; Roffe, G.; Miller, G.

    1985-12-01

    Thermal preconditioning is a process in which coal/water mixtures are vaporized to produce coal/steam suspensions, and then superheated to allow the coal to devolatilize producing suspensions of char particles in hydrocarbon gases and steam. This final product of the process can be injected without atomization, and burned directly in a gas turbine combustor. This paper reports on the results of an experimental program in which thermally preconditioned coal/water mixture was successfully burned with a stable flame in a gas turbine combustor test rig. Tests were performed at a mixture flowrate of 300 lb/hr and combustor pressure of 8 atmospheres. The coal/water mixture was thermally preconditioned and injected into the combustor over a temperature range from 350 to 600/sup 0/F, and combustion air was supplied at between 600 to 725/sup 0/F. Test durations generally varied between 10 to 20 minutes. Major results of the combustion testing were that: a stable flame was maintained over a wide equivalence ratio range, between phi = 2.4 (rich) to 0.2 (lean); and, combustion efficiency of over 99% was achieved when the mixture was preconditioned to 600/sup 0/F and the combustion air preheated to 725/sup 0/F. Measurements of ash particulates captured in the exhaust sampling probe located 20 inches from the injector face, show typical sizes collected to be about 1 micron, with agglomerates of these particulates to be not more than 8 microns. The original mean coal particle size for these tests, prior to preconditioning was 25 microns. System studies indicate that preconditioning can be incorporated into either stationary or mobile power plant designs without system derating. On the basis of these results, thermal pretreatment offers a practical alternative to fuel atomization in gas turbine applications. 20 figs., 4 tabs.

  11. Potentials of Biomass Co-Combustion in Coal-Fired Boilers

    NASA Astrophysics Data System (ADS)

    Werther, J.

    The present work provides a survey on the potentials of co-combustion of biomass and biogenic wastes in large-scale coal-fired power plants. This allows an energetic utilization at a high level of efficiency which is not obtainable in small-scale dedicated biomass combustors. Co-firing at low percentages of the thermal power (typically below 5-10 %) avoids the characteristic operating problems of biomass combustion, i.e. ash sintering and fouling of heat transfer surfaces. Co-firing of biogenic wastes is already widely practiced in Germany, non-waste biomass like forest residues are for subsidy reasons combusted in small dedicated mono-combustion plants. A future increase of co-combustion may be associated with the upgrading of biogenic wastes with high water content to biofuels by drying. Such biofuels could substitute more expensive coal and save on CO2 emission certificates. In the more distant future biomass co-combustion may help in the CO2 scrubbing process by lowering the target level of CO2 absorption efficiency.

  12. Cofiring coal-water slurry in cyclone boilers: Some combustion issues and considerations

    SciTech Connect

    Carson, W.R.; Tillman, D.

    1997-07-01

    Coal-water slurry (CWS) has become a fuel of opportunity with the ability to impact fuel cost at selected power plants; at the same time it has the potential to reduce emissions of oxides of nitrogen (NO{sub x}) by driving specific combustion mechanisms. CWS, produced from selected fines generated during coal cleaning operations, has been fired extensively at the Seward Generating Station of General Public Utilities (GPU), and testing has been initiated at cyclone plants as well. Initial combustion modeling of cyclones has shown that the critical issues associated with CWS firing in cyclones include the following: (1) the impact of CWS on fuel chemistry, with particular attention to fuel ash chemistry; (2) the impact of CWS on combustion temperatures; (3) the impact of CWS, and the consequent increased gas flow in the cyclones, on combustion processes in the cyclone barrel and potentially on combustion in the primary furnace as well; (4) the consequence of combustion process changes on patterns of heat release in the cyclone barrel and in the primary furnace; (5) the ability of the CWS to impact NO{sub x} emissions in the cyclone; and (6) the impact of CWS on the formation of trace metal emissions. This paper reviews the results of cyclone boiler modeling, and also reviews some results of initial cyclone testing related to the results of the modeling efforts.

  13. Arsenic in coal of the Thar coalfield, Pakistan, and its behavior during combustion.

    PubMed

    Ali, Jamshed; Kazi, Tasneem G; Baig, Jameel A; Afridi, Hassan I; Arain, Mariam S; Brahman, Kapil D; Naeemullah; Panhwar, Abdul H

    2015-06-01

    The aim of the current study is to evaluate the occurrence of arsenic in coal collected from Thar coalfield, Pakistan, and its behavior during the combustion. Fractionation of arsenic (As) in coal samples was carried out by Community Bureau of Reference sequential extraction scheme (BCR-SES) and single-step-based BCR method (BCR-SS). These methods are validated using the certified reference material of sediment BCR 701 and standard addition method. The stepwise fractions of As in laboratory-made ash (LMA) have been also investigated. The extractable As content associated with different phases in coal and LMA samples were analyzed by electrothermal atomic absorption spectrophotometer. The extraction efficiency of As by BCR-SS was slightly higher than BCR-SES, while the difference was not significant (p < 0.05). The BCR-SS method is a time-saving method because it can reduce the extraction time from 51 to 22 h. The As contents in LMA revealed that during combustion of the coal, >85 % of As may be released into atmosphere. The relative mobility of As in the coal samples was found in increasing order as follows: oxidizable fraction < reducible fraction < acid soluble fraction. The total and extractable As obtained by BCR-SES and BCR-SS were higher in coal samples of block III as compared to block V (p > 0.05). PMID:25561265

  14. Transformations of inorganic coal constituents in combustion systems

    SciTech Connect

    Helble, J.J.; Srinivasachar, S.; Wilemski, G.; Boni, A.A. ); Kang, Shin-Gyoo; Sarofim, A.F.; Beer, J.M. ); Peterson, T.W.; Wendt, J.O.L.; Gallagher, N.B.; Bool, L. ); Shah, N.; Huggins, F.E.; Huffman, G.P. )

    1991-09-01

    The technical objectives of this project are: (1) To define the partitioning of inorganic constituents associated with raw coal particles among products (including vapors, aerosols, and residual char/ash particles) formed under conditions representative of pulverized coal flames as a function of the specific (intrinsic and extrinsic) characteristics of the raw coal and the environment in which the transformations occur; and to characterize the resultant spectrum of products in detail. (2) To elucidate and quantify the fundamental processes (involving basic principles of physics, chemistry, thermodynamics) by which transformations of the inorganic constituents occur; and (3) to develop, based on the information required in (1) and (2), a tractable process'' model capable of predicting the significant features of the transformation process, most importantly, the nature and distribution of products. 26 refs., 151 figs., 51 tabs.

  15. Distribution of coal combustion derived heavy metals on croplands in China

    NASA Astrophysics Data System (ADS)

    Zhao, R.; Ying, S.; Bu, J.; Weiss, D. J.; Gan, Y.; Wilcox, J.; Lambin, E.; Fendorf, S.

    2013-12-01

    As the world's number one consumer of energy derived from coal, China produces massive amounts of coal combustion by-products annually, including fly ash, which can then be transported and deposited onto agricultural lands. To explore the impact of fly ash as a point source of heavy metals to crops, we use a combination of spatial, thermodynamic, and coal combustion models and field measurements to determine the amount and composition of fly ash that is distribute over different land cover types around a power plant in China. First, a database of Chinese coal compositions was created to determine the range in chemical concentrations of heavy metals in coals. Using this information, we then determined the amount of fly ash produced by a typical power plant by applying the Integrated Environmental Control Model (IECM). An estimate of the composition of fly ash (based on the coal composition) is then predicted by thermodynamic equilibrium calculations. The resulting information regarding the concentration of As, Pb, and Cd in the fly ash is entered into an atmospheric transport model which determines the mass of fly ash deposited as a function of distance from the stack. Transport modeling results, land cover data, and topographic information are incorporated using GIS to determine the croplands affected by fly ash deposition. Furthermore, we determine the Pb206/Pb207 isotopic ratios of coal and fly ash taken from Yangluo Power Plant in Wuhan, Hubei Province, China, and compare the values to those measured in soils collected within a 10 km radius around the power plant. Ultimately, the results of this project can be utilized in a comprehensive model that can determine the amount and distribution of heavy metals from fly ash produced by coal-fired power plants based on coal composition and power plant specifications.

  16. Coal combustion under conditions of blast furnace injection. Technical report, March 1, 1994--May 31, 1994

    SciTech Connect

    Crelling, J.C.

    1994-09-01

    A potentially new use for Illinois coal is its use as a fuel injected into a blast furnace to produce molten iron as the first step in steel production. Because of its increasing cost and decreasing availability, metallurgical coke is now being replaced by coal injected at the tuyere area of the furnace where the blast air enters. The purpose of this study is to evaluate the combustion of coal during the blast furnace injection process and to delineate the optimum properties of the feed coal. This investigation is significant to the use of Illinois coal in that the limited research to date suggests that coals of low fluidity and moderate to high sulfur and chlorine contents are suitable feedstocks for blast furnace injection. This proposal is a follow-up to one funded for the 1992-93 period. It is intended to complete the study already underway with the Armco Inc. Steel Company and to initiate a new cooperative study along somewhat similar lines with the Inland Steel Company. The results of this study will lead to the development of a testing and evaluation protocol that will give a unique and much needed understanding of the behavior of coal in the injection process and prove the potential of Illinois coals for such use. During this quarter samples of two feed coals and the IBCSP 112 (Herrin No. 6) were prepared for reactivity testing and compared to blast furnace coke, and char fines taken from an active blast furnace. As the initial part of a broad reactivity analysis program, these same samples were also analyzed on a thermogravimetric analyzer (TGA) to determine their combustion and reactivity properties.

  17. Effect of organic calcium compounds on combustion characteristics of rice husk, sewage sludge, and bituminous coal: thermogravimetric investigation.

    PubMed

    Zhang, Lihui; Duan, Feng; Huang, Yaji

    2015-04-01

    Experiments were conducted in a thermogravimetric analyzer to assess the enhancement of combustion characteristics of different solid fuels blended with organic calcium compounds (OCCs). Rice husk, sewage sludge, and bituminous coal, and two OCC were used in this study. Effect of different mole ratios of calcium to sulfur (Ca/S ratio) on the combustion characteristics were also investigated. Results indicated that combustion performance indexes for bituminous coal impregnated by OCC were improved, however, an inverse trend was found for sewage sludge because sewage sludge has lower ignition temperature and higher volatile matter content compared to those of OCC. For rice husk, effect of added OCC on the combustion characteristics is not obvious. Different solid fuels show different combustion characteristics with increases of Ca/S ratio. The maximum combustion performance indexes appear at Ca/S ratios of 1:1, 2:1, and 3:1 for OCC blended with Shenhua coal, rice husk, and sewage sludge, respectively. PMID:25638405

  18. COMBUSTION RESEARCH ON THE FATE OF FUEL-NITROGEN UNDER CONDITIONS OF PULVERIZED COAL COMBUSTION

    EPA Science Inventory

    The report gives results of an experimental investigation of coal pyrolysis and oxidation, and char oxidation to determine the effects of temperature and fuel/oxygen equivalence ratio on the conversion of coal-nitrogen to NOx. Experiments involved a laboratory laminar flow furnac...

  19. Interactions of coal gangue and pine sawdust during combustion of their blends studied using differential thermogravimetric analysis.

    PubMed

    Zhang, Yuanyuan; Zhang, Zhezi; Zhu, Mingming; Cheng, Fangqin; Zhang, Dongke

    2016-08-01

    The interactions between coal gangue and pine sawdust during the combustion process were studied using thermogravimetric analysis. The effect of the blending ratio, oxygen concentration and heating rate on the weight loss (TG) and differential thermogravimetric (TGA) profiles was examined. The TG and DTG curves of the blends were not additives of those of the individual materials, suggesting that interactions between coal gangue and pine sawdust had occurred during the combustion, especially in the temperature range of 400-600°C. Kinetic analysis confirmed that the combustion of coal gangue, pine sawdust and their blends was chemical reaction controlled. Further analysis revealed that the interactions between coal gangue and pine sawdust were primarily due to thermal effects rather than structural changes, with the thermal inertia of coal gangue dominating over the behaviour of the blends. The interactions decreased with decreasing the coal gangue ratio in the blend, oxygen concentration and heating rate. PMID:27155794

  20. NOx, FINE PARTICLE AND TOXIC METAL EMISSIONS FROM THE COMBUSTION OF SEWAGE SLUDGE/COAL MIXTURES: A SYSTEMATIC ASSESSMENT

    SciTech Connect

    Jost O.L. Wendt

    2002-08-15

    This research project focuses on pollutants from the combustion of mixtures of dried municipal sewage sludge (MSS) and coal. The objective is to determine the relationship between (1) fraction sludge in the sludge/coal mixture, and (2) combustion conditions on (a) NOx concentrations in the exhaust, (b) the size segregated fine and ultra-fine particle composition in the exhaust, and (c) the partitioning of toxic metals between vapor and condenses phases, within the process. The proposed study will be conducted in concert with an existing ongoing research on toxic metal partitioning mechanisms for very well characterized pulverized coals alone. Both high NOx and low NOx combustion conditions will be investigated (unstaged and staged combustion). Tradeoffs between CO2 control, NOx control, and inorganic fine particle and toxic metal emissions will be determined. Previous research has yielded data on trace metal partitioning for MSS by itself, with natural gas assist, for coal plus MSS combustion together, and for coal alone. We have re-evaluated the inhalation health effects of ash aerosol from combustion of MSS both by itself and also together with coal. We have concluded that ash from the co-combustion of MSS and coal is very much worse from an inhalation health point of view, than ash from either MSS by itself or coal by itself. The reason is that ZnO is not the ''bad actor'' as had been suspected before, but the culprit is, rather, sulfated Zn. The MSS supplies the Zn and the coal supplies the sulfur, and so it is the combination of coal and MSS that makes that process environmentally bad. If MSS is to be burned, it should be burned without coal, in the absence of sulfur.

  1. Large-scale studies of spontaneous combustion of coal. Rept. of investigations/1991

    SciTech Connect

    Smith, A.C.; Miron, Y.; Lazzara, C.P.

    1991-01-01

    The U.S. Bureau of Mines constructed a large-scale facility to study the self-heating of a large coal mass under conditions that simulate a gob area of a mine. The insulated coal chamber can hold up to 13 short tons (st) of coal and is provided with a forced ventilation system and computer-controlled temperature and gas measurement systems to monitor the heat and mass transfer phenomena that occur in the coalbed. Three experiments were completed with high-volatile C bituminous coals that exhibited high spontaneous combustion potentials in laboratory-scale tests. In the first two tests, a sustained heating was not achieved. In the third test, temperatures throughout the coalbed increased steadily from the start, with thermal runaway occurring near the center of the coalbed after 23 days. The thermal reaction zone then moved toward the front of the coalbed. The results of these tests showed that the self-heating of a large coal mass depends not just on the reactivity of the coal, but also on the particle size of the coal, the freshness of the coal surfaces, the heat-of-wetting effect, and the availability of O2 at optimum ventilation rates.

  2. [Quantitative spectrum analysis of characteristic gases of spontaneous combustion coal].

    PubMed

    Liang, Yun-Tao; Tang, Xiao-Jun; Luo, Hai-Zhu; Sun, Yong

    2011-09-01

    Aimed at the characteristics of spontaneous combustion gas such as a variety of gases, lou limit of detection, and critical requirement of safety, Fourier transform infrared (FTIR) spectral analysis is presented to analyze characteristic gases of spontaneous combustion In this paper, analysis method is introduced at first by combing characteristics of absorption spectra of analyte and analysis requirement. Parameter setting method, sample preparation, feature variable abstract and analysis model building are taken into consideration. The methods of sample preparation, feature abstraction and analysis model are introduced in detail. And then, eleven kinds of gases were tested with Tensor 27 spectrometer. CH4, C2H6, C3H8, iC4H10, nC4H10, C2 H4, C3 H6, C3 H2, SF6, CO and CO2 were included. The optical path length was 10 cm while the spectra resolution was set as 1 cm(-1). The testing results show that the detection limit of all analytes is less than 2 x 10(-6). All the detection limits fit the measurement requirement of spontaneous combustion gas, which means that FTIR may be an ideal instrument and the analysis method used in this paper is competent for spontaneous combustion gas measurement on line. PMID:22097853

  3. Fireside corrosion in oxy-fuel combustion of coal

    SciTech Connect

    Holcomb, Gordon R.; Tylczak, Joseph; Meier, Gerald H.; Jung, Kee Young; Mu, Nan; Yanar, Nazik M.; Pettit, Frederick S.

    2011-08-01

    Oxy-fuel combustion is based on burning fossil fuels in a mixture of recirculated flue gas and oxygen, rather than in air. An optimized oxy-combustion power plant will have ultra-low emissions since the flue gas that results from oxy-fuel combustion consists almost entirely of CO2 and water vapor. Once the water vapor is condensed, it is relatively easy to sequester the CO2 so that it does not escape into the atmosphere. A variety of laboratory tests comparing air-firing to oxy-firing conditions, and tests examining specific simpler combinations of oxidants, were conducted at 650-700 C. Alloys studied included model Fe-Cr and Ni-Cr alloys, commercial ferritic steels, austenitic steels, and nickel base superalloys. Furthermore, the observed corrosion behavior shows accelerated corrosion even with sulfate additions that remain solid at the tested temperatures, encapsulation of ash components in outer iron oxide scales, and a differentiation between oxy-fuel combustion flue gas recirculation choices.

  4. Fireside corrosion in oxy-fuel combustion of coal

    DOE PAGESBeta

    Holcomb, Gordon R.; Tylczak, Joseph; Meier, Gerald H.; Jung, Kee Young; Mu, Nan; Yanar, Nazik M.; Pettit, Frederick S.

    2011-08-01

    Oxy-fuel combustion is based on burning fossil fuels in a mixture of recirculated flue gas and oxygen, rather than in air. An optimized oxy-combustion power plant will have ultra-low emissions since the flue gas that results from oxy-fuel combustion consists almost entirely of CO2 and water vapor. Once the water vapor is condensed, it is relatively easy to sequester the CO2 so that it does not escape into the atmosphere. A variety of laboratory tests comparing air-firing to oxy-firing conditions, and tests examining specific simpler combinations of oxidants, were conducted at 650-700 C. Alloys studied included model Fe-Cr and Ni-Crmore » alloys, commercial ferritic steels, austenitic steels, and nickel base superalloys. Furthermore, the observed corrosion behavior shows accelerated corrosion even with sulfate additions that remain solid at the tested temperatures, encapsulation of ash components in outer iron oxide scales, and a differentiation between oxy-fuel combustion flue gas recirculation choices.« less

  5. ULTRAFINE ASH AEROSOLS FROM COAL COMBUSTION: CHARACTERIZATION AND HEALTH EFFECTS

    EPA Science Inventory

    Ultrafine coal fly ash particles, defined here as those with diameters less than 0.5 micrometer, typically comprise less than 1% of the total fly ash mass. These particles are formed almost exclusively through ash vaporization, nucleation, and coagulation/condensation mechanisms,...

  6. POLLUTANT FORMATION DURING FIXED-BED AND SUSPENSION COAL COMBUSTION

    EPA Science Inventory

    The report summarizes a 3-year study of the formation and control of nitrogen and sulfur oxides (NOx and SOx) in industrial coal-fired boilers, with emphasis on stoker-fired units. Three major research areas were considered: the evolution and oxidation of fuel nitrogen and sulfur...

  7. Heavy duty gas turbine combustion tests with simulated low BTU coal gas

    SciTech Connect

    Ekstrom, T.E.; Battista, R.A.; Belisle, F.H.; Maxwell, G.P.

    1993-11-01

    This program has the objectives to: A. Parametrically determine the effects of moisture, nitrogen and carbon dioxide as diluents so that the combustion characteristics of many varieties of gasification product gases can be reasonably predicted without physically testing each specific gas composition. B. Determine emissions characteristics including NO, NO{sub x}, CO, levels etc. associated with each of the diluents, and C. Operate with at least two syngas compositions; DOE chosen air-blown and integrated oxygen-blown, to confirm that the combustion characteristics are in line with predictions. As a result of this program: 1. GE Engineering is now confident that the syngas fuels produced by all currently--viable coal gasifiers can be accommodated by the GE advanced (``F`` Technology) combustion system, and 2. For proposed syngas fuels with varying amounts of steam, nitrogen or CO{sub 2} diluent, the combustion and emissions characteristics can be reasonably estimated without undertaking expensive new screening tests for each different fuel.

  8. EFFECTS OF COFIRING LIGNIN AND BIOSOLIDS WITH COAL ON FIRESIDE PERFORMANCE AND COMBUSTION PRODUCTS

    SciTech Connect

    Kevin C. Galbreath

    2002-08-01

    Lignin, derived from municipal solid waste and biosolid feedstocks using Masada Resource Group's patented CES OxyNol{trademark} process, and acidified biosolids were evaluated as supplemental fuels with coal for producing steam and electricity. Tests were conducted in a pilot-scale (550,000-Btu/hr [580-MJ/hr]) combustion system to evaluate the effects of coal characteristics, blend mixture (on a dry wt% basis) and furnace exit gas temperature (FEGT) on boiler heat-exchange surface slagging and fouling, NO{sub x} and SO{sub x} production, fly ash characteristics, and combustion efficiency. The effects of blending lignin and acidified biosolids with coal on fuel handling and pulverization characteristics were also addressed. An 80 wt% Colorado--20 wt% subbituminous Powder River Basin coal blend from the Tennessee Valley Authority Colbert Steam Plant, hereafter referred to as the Colbert coal, and a bituminous Pittsburgh No. 8 coal were tested. The lignin and acidified biosolids were characterized by possessing higher moisture content and lower carbon, hydrogen, and heating values relative to the coals. Ash contents of the fuels were similar. The lignin also possessed higher concentrations of TiO{sub 2}, CaO, and SO{sub 3} and lower concentrations of SiO{sub 2}, Al{sub 2}O{sub 3}, Fe{sub 2}O{sub 3}, K{sub 2}O, and N relative to the coals. The sulfur content of lignin could be reduced through a more thorough washing and drying of the lignin in an efficient commercial-scale dewatering device. Acidified biosolids were distinguished by higher concentrations of P{sub 2}O{sub 5} and MgO and lower SiO{sub 2} and Al{sub 2}O{sub 3} relative to the other fuels. Trace element concentrations, especially for Cr, Pb, Hg, and Ni, were generally greater in the lignin and acidified biosolid fuels relative to the Colbert coal. Maximum trace element emission factors were calculated for 95:5 Colbert coal--lignin and 90:5:5 Colbert coal--lignin--acidified biosolid blends and compared to U

  9. The value of coal combustion products: an economic assessment of CCP unitization for the US economy

    SciTech Connect

    Steward, A.

    2005-07-01

    The recently released study by the American Coal Council (ACC) on 'The Value of Coal Combustion Products' provides a detailed economic assessment of CCP utilization for US markets and the US economy. Over 125 million tons of CCPs are produced in the US each year. The projected growth in the nation's utility-coal industry will result in the production of even greater volumes of CCPs. The ACC study details: how CCPs are currently being utilized; what factors are affecting utilization growth; what are the economic benefits of avoiding disposal costs; what is the annual revenue potential of CCP utilization; what direct economic benefits in employment and tax revenues can be gained; and what indirect economic benefits are available for support industries, coal consumers and the building industry. 9 refs., 16 tabs.

  10. Combustion behavior of single coal-water slurry droplets, Part 1: Experimental techniques

    SciTech Connect

    Levendis, Y.A.; Metghalchi, M.; Wise, D.

    1991-12-31

    Techniques to produce single droplets of coal-water slurries have been developed in order to study the combustion behavior of the slurries. All stages of slurry combustion are of interest to the present study, however, emphasis will be given to the combustion of the solid agglomerate char which remains upon the termination of the water evaporation and the devolatilization periods. An experimental facility is under construction where combustion of coal-water slurries will be monitored in a variety of furnace temperatures and oxidizing atmospheres. The effect of the initial size of the slurry droplet and the solids loading (coal to water ratio) will be investigated. A drop tube, laminar flow furnace coupled to a near-infrared, ratio pyrometer win be used to monitor temperature-time histories of single particles from ignition to extinction. This paper describes the experimental built-up to this date and presents results obtained by numerical analysis that help understanding the convective and radiating environment in the furnace.

  11. Pathways for conversion of char nitrogen to nitric oxide during pulverized coal combustion

    SciTech Connect

    Molina, A.; Murphy, J.J.; Blevins, L.G.; Shaddix, C.R.; Winter, F.; Haynes, B.S.

    2009-03-15

    The conversion of nitrogen in char (char-N) to NO was studied both experimentally and computationally. In the experiments, pulverized coal char was produced from a U.S. high-volatile bituminous coal and burned in a dilute suspension at 1170 K, 1370 K and 1570 K, at an excess oxygen concentration of 8% (dry), with different levels of background NO. In some experiments, hydrogen bromide (HBr) was added to the vitiated air as a tool to alter the concentration of gas-phase radicals. During char combustion, low NO concentration and high temperature promoted the conversion of char-N to NO. HBr addition altered NO production in a way that depended on temperature. At 1170 K the presence of HBr increased NO production by 80%, whereas the addition of HBr decreased NO production at higher temperatures by 20%. To explain these results, three mechanistic descriptions of char-N evolution during combustion were evaluated with computational models that simulated (a) homogeneous chemistry in a plug-flow reactor with entrained particle combustion, and (b) homogeneous chemistry in the boundary layer surrounding a reacting particle. The observed effect of HBr on NO production could only be captured by a chemical mechanism that considered significant release of HCN from the char particle. Release of HCN also explained changes in NO production with temperature and NO concentration. Thus, the combination of experiments and simulations suggests that HCN evolution from the char during pulverized coal combustion plays an essential role in net NO production. (author)

  12. Biomass gasification chars for mercury capture from a simulated flue gas of coal combustion.

    PubMed

    Fuente-Cuesta, A; Diaz-Somoano, M; Lopez-Anton, M A; Cieplik, M; Fierro, J L G; Martínez-Tarazona, M R

    2012-05-15

    The combustion of coal can result in trace elements, such as mercury, being released from power stations with potentially harmful effects for both human health and the environment. Research is ongoing to develop cost-effective and efficient control technologies for mercury removal from coal-fired power plants, the largest source of anthropogenic mercury emissions. A number of activated carbon sorbents have been demonstrated to be effective for mercury retention in coal combustion power plants. However, more economic alternatives need to be developed. Raw biomass gasification chars could serve as low-cost sorbents for capturing mercury since they are sub-products generated during a thermal conversion process. The aim of this study was to evaluate different biomass gasification chars as mercury sorbents in a simulated coal combustion flue gas. The results were compared with those obtained using a commercial activated carbon. Chars from a mixture of paper and plastic waste showed the highest retention capacity. It was found that not only a high carbon content and a well developed microporosity but also a high chlorine content and a high aluminium content improved the mercury retention capacity of biomass gasification chars. No relationship could be inferred between the surface oxygen functional groups and mercury retention in the char samples evaluated. PMID:22325640

  13. Char crystalline transformations during coal combustion and their implications for carbon burnout

    SciTech Connect

    Hurt, R.H.

    1999-07-07

    Residual, or unburned carbon in fly ash affects many aspects of power plant performance and economy including boiler efficiency, electrostatic precipitator operation, and ash as a salable byproduct. There is a large concern in industry on the unburned carbon problem due to a variety of factors, including low-NOx combustion system and internationalization of the coal market. In recent work, it has been found that residual carbon extracted from fly ash is much less reactive than the laboratory chars on which the current kinetics are based. It has been suggested that thermal deactivation at the peak temperature in combustion is a likely phenomenon and that the structural ordering is one key mechanism. The general phenomenon of carbon thermal annealing is well known, but there is a critical need for more data on the temperature and time scale of interest to combustion. In addition, high resolution transmission electron microscopy (HRTEM) fringe imaging, which provides a wealth of information on the nature and degree of crystallinity in carbon materials such as coal chars, has become available. Motivated by these new developments, this University Coal Research project has been initiated with the following goals: (1) To determine transient, high-temperature, thermal deactivation kinetics as a function of parent coal and temperature history. (2) To characterize the effect of the thermal treatment on carbon crystalline structure through high-resolution transmission electron microscopy and specialized, quantitative image analysis.

  14. Transformations of inorganic coal constituents in combustion systems. Volume 1, sections 1--5: Final report

    SciTech Connect

    Helble, J.J.; Srinivasachar, S.; Wilemski, G.; Boni, A.A.; Kang, Shin-Gyoo; Sarofim, A.F.; Graham, K.A.; Beer, J.M.; Peterson, T.W.; Wendt, J.O.L.; Gallagher, N.B.; Bool, L.; Huggins, F.E.; Huffman, G.P.; Shah, N.; Shah, A.

    1992-11-01

    The inorganic constituents or ash contained in pulverized coal significantly increase the environmental and economic costs of coal utilization. For example, ash particles produced during combustion may deposit on heat transfer surfaces, decreasing heat transfer rates and increasing maintenance costs. The minimization of particulate emissions often requires the installation of cleanup devices such as electrostatic precipitators, also adding to the expense of coal utilization. Despite these costly problems, a comprehensive assessment of the ash formation and had never been attempted. At the start of this program, it was hypothesized that ash deposition and ash particle emissions both depended upon the size and chemical composition of individual ash particles. Questions such as: What determines the size of individual ash particles? What determines their composition? Whether or not particles deposit? How combustion conditions, including reactor size, affect these processes? remained to be answered. In this 6-year multidisciplinary study, these issues were addressed in detail. The ambitious overall goal was the development of a comprehensive model to predict the size and chemical composition distributions of ash produced during pulverized coal combustion. Results are described.

  15. Combustion characterization of beneficiated coal-based fuels. Quarterly report No. 5, May 1990--June 1990

    SciTech Connect

    Chow, O.K.; Nsakala, N.Y.

    1990-08-01

    The objectives of this project include: (1) the development of an engineering data base which will provide detailed information on the properties of BCFs influencing combustion, ash deposition, ash erosion, particulate collection, and emissions; and (2) the application of this technical data base to predict the performance and economic impacts of firing the BCFs in various commercial boiler designs. The technical approach used to develop the technical data includes: bench-scale fuel property, conbustion, and ash deposition tests; pilot-scale combustion and ash effects tests; and full-scale combustion tests. Subcontractors to CE to perform parts of the test work are the Massachusetts Institute of Technology (MIT), Physical Sciences, Inc. Technology Company (PSIT) and the University of North Dakota Energy and Environmental Research Center (UNDEERC). Twenty fuels will be characterized during the three-year base program: three feed coals, fifteen BCFs, and two conventionally cleaned coals for the full-scale tests. Approximately nine BCFs will be in dry ultra-fine coal (DUC) form, and six BCFs will be in coal-water fuel (CWF) form. Additional BCFs would be characterized during optional project supplements.

  16. Structure-Based Predictive model for Coal Char Combustion.

    SciTech Connect

    Hurt, R.; Calo, J.; Essenhigh, R.; Hadad, C; Stanley, E.

    1997-03-28

    The first quarter of this project was used to carry out a detailed planning process to coordinate the various aspects of this collaborative effort. A workshop was held at Brown University on December 4, 1996, attended by all project participants and key visitors, in which presentations were given by the principal investigators on their respective subtasks. The planning process culminated in the completion of a comprehensive document submitted to DOE / FETC under separate cover. Following the planning exercise, research work was initiated and will be continued in the second project quarter.

  17. The role of combustion diagnostics in coal quality impact and NO{sub x} emissions field test programs

    SciTech Connect

    Thompson, R.E.; Dyas, B.

    1995-03-01

    Many utilities are examining low sulfur coal or coal blending options to comply with the Clean Air Act Amendment SO{sub 2} emission limits. Test burns have been conducted with the more promising candidate coals to characterize the potential impact of a change in coal quality on boiler operation and performance. Utilities are also under considerable pressure to evaluate NO{sub x} control options and develop a compliance plan to meet strict NO{sub x} regulations, particularly in high population density metropolitan areas on the Eastern seaboard. Field test programs have been conducted to characterize baseline NO{sub x} emissions, evaluate the NO{sub x} reduction potential of combustion modifications, and assess the potential of combustion tuning as an alternative to burner replacement. Coal quality impacts (slagging, fouling, heat absorption, ash removal) and NO{sub x} emissions are both strongly dependent upon the coal combustion process and site-specific boiler firing practices. Non-uniform combustion in the burner region can result in adverse ash deposition characteristics, carbon carryover problems, high furnace exit gas temperatures, and NO{sub x}emission characteristics that are not representative of the coal or the combustion equipment. Advanced combustion diagnostic test procedures have been developed to evaluate and improve burner zone combustion uniformity, even in cases where the coal flow to the individual burners may be non-uniform. The paper outlines a very practical solving approach to identifying combustion related problems that affect ash deposition and NO{sub x} emissions. The benefits of using advanced diagnostic instrumentation to identify problems and tune combustion conditions is illustrated using test data from recent quality field test programs.

  18. Combustion characteristics of pulverized coal and air/gas premixed flame in a double swirl combustor

    SciTech Connect

    Kamal, M.M.

    2009-07-01

    An experimental work was performed to investigate the co-firing of pulverized coal and premixed gas/air streams in a double swirl combustor. The results showed that the NOx emissions are affected by the relative rates of thermal NOx formation and destruction via the pyrolysis of the fuel-N species in high temperature fuel-rich zones. Various burner designs were tested in order to vary the temperature history and the residence time across both coal and gas flames inside the furnace. It was found that by injecting the coal with a gas/air mixture as a combined central jet surrounded by a swirled air stream, a double flame envelope develops with high temperature fuel-rich conditions in between the two reaction zones such that the pyrolysis reactions to N{sub 2} are accelerated. A further reduction in the minimum NOx emissions, as well as in the minimum CO concentrations, was reported for the case where the coal particles are fed with the gas/air mixture in the region between the two swirled air streams. On the other hand, allocating the gas/air mixture around the swirled air-coal combustion zone provides an earlier contact with air and retards the NOx reduction mechanism in such a way that the elevated temperatures around the coal particles allow higher overall NOx emissions. The downstream impingement of opposing air jets was found more efficient than the impinging of particle non-laden premixed flames for effective NOx reduction. In both cases, there is an upstream flow from the stagnation region to the coal primary combustion region, but with the case of air impingement, the hot fuel-rich zone develops earlier. The optimum configuration was found by impinging all jets of air and coal-gas/air mixtures that pronounced minimum NOx and CO concentrations of 310 and 480ppm, respectively.

  19. Distribution of polycyclic aromatic hydrocarbons in fly ash during coal and residual char combustion in a pressurized fluidized bed

    SciTech Connect

    Hongcang Zhou; Baosheng Jin; Rui Xiao; Zhaoping Zhong; Yaji Huang

    2009-04-15

    To investigate the distribution of polycyclic aromatic hydrocarbons (PAHs) in fly ash, the combustion of coal and residual char was performed in a pressurized spouted fluidized bed. After Soxhlet extraction and Kuderna-Danish (K-D) concentration, the contents of 16 PAHs recommended by the United States Environmental Protection Agency (U.S. EPA) in coal, residual char, and fly ash were analyzed by a high-performance liquid chromatography (HPLC) coupled with fluorescence and diode array detection. The experimental results show that the combustion efficiency is lower and the carbon content in fly ash is higher during coal pressurized combustion, compared to the residual char pressurized combustion at the pressure of 0.3 MPa. Under the same pressure, the PAH amounts in fly ash produced from residual char combustion are lower than that in fly ash produced from coal combustion. The total PAHs in fly ash produced from coal and residual char combustion are dominated by three- and four-ring PAHs. The amounts of PAHs in fly ash produced from residual char combustion increase and then decrease with the increase of pressure in a fluidized bed. 21 refs., 1 fig., 4 tabs.

  20. Combustion of Illinois coals and chars with natural gas. Technical report, December 1, 1991--February 29, 1992

    SciTech Connect

    Buckinus, R.O.; Peters, J.E.; Krier, H.

    1992-08-01

    The combined combustion of coal and natural gas offers advantageous compared to burning coal or natural gas alone. For example, low volatile coals or low volatile chars derived from treatment or gasification processes can be of limited use due to their poor flammability characteristics. However, the use of natural gas in conjunction with the solid fuel can provide the necessary ``volatiles`` to enhance the combustion. Additionally, natural gas provides a clean cofiring fuel source which can enhance the usefulness of coals with high sulfur content. Addition of natural gas may reduce SO{sub x} emissions through increased sulfur retention in the ash and reduce NO{sub x} emissions by varying local stoichiometry and temperature levels. In this research program, studies of combined Illinois coal and natural gas combustion provide particle ignition, burnout rates and ash characterization, helping clarify the effect of coal and natural gas and identify the controlling parameters and mechanisms. The Drop Tube Furnace Facility allows detailed measurements of coal particle combustion under well-controlled conditions. The combustion characteristics of single coal particles are determined through a novel set of diagnostic techniques including in situ simultaneous measurements of particle morphology, temperature and velocity. The emphasis of the effort in the second quarter of this project was on the understanding of the ignition enhancement, burning rate processes during cofiring, and sulfur retention in the ash.

  1. Fireside Corrosion in Oxy-Fuel Combustion of Coal

    SciTech Connect

    G. R. Holcomb; J. Tylczak; G. H. Meier; K. Jung; N. Mu; N. M. Yanar; F. S. Pettit

    2011-10-09

    The goal is to develop technologies for pulverized coal boilers with >90% CO{sub 2} capture and sequestration and <35% increase in the cost of electricity. Air-fired power plant experience shows a corrosion loss max at 680-700 C. Low melting point alkali metal trisulfates, such as (K,Na){sub 3}Fe(SO{sub 4}){sub 3}, become thermally unstable above this temperature range. Some overall conclusions are: (1) CO{sub 2} + 30% H{sub 2}O more corrosive than Ar + 30% H{sub 2}O; (2) Excess O{sub 2} in H{sub 2}O can, in some cases, greatly increase oxidation; (3) Coal ash is generally innocuous without SO{sub 3}3 in gas phase; and (4) Long-term exposures are starting to establish differences between air-firing and oxy-firing conditions.

  2. UTILIZATION OF LOW NOx COAL COMBUSTION BY-PRODUCTS

    SciTech Connect

    J.Y. Hwang; X. Huang; M.G. McKimpson; R.E. Tieder; A.M. Hein; J.M. Gillis; D.C. Popko; K.L. Paxton; Z. Li; X. Liu; X. Song; R.I. Kramer

    1998-12-01

    Low NO{sub x} combustion practices are critical for reducing NO{sub x} emissions from power plants. These low NO{sub x} combustion practices, however, generate high residual carbon contents in the fly ash produced. These high carbon contents threaten utilization of this combustion by-product. This research has successfully developed a separation technology to render fly ash into useful, quality-controlled materials. This technology offers great flexibility and has been shown to be applicable to all of the fly ashes tested (more than 10). The separated materials can be utilized in traditional fly ash applications, such as cement and concrete, as well as in nontraditional applications such as plastic fillers, metal matrix composites, refractories, and carbon adsorbents. Technologies to use beneficiated fly ash in these applications are being successfully developed. In the future, we will continue to refine the separation and utilization technologies to expand the utilization of fly ash. The disposal of more than 31 million tons of fly ash per year is an important environmental issue. With continued development, it will be possible to increase economic, energy and environmental benefits by re-directing more of this fly ash into useful materials.

  3. Coal-ash Corrosion of Alloys for Combustion Power Plants

    SciTech Connect

    Natesan, K.; Purohit, A.; Rink, D.L.

    2003-04-22

    A program on coal-ash corrosion is being conducted at Argonne National Laboratory to evaluate the performance of several structural alloys in the presence of mixtures of synthetic coal ash, alkali sulfates, and alkali chlorides. Candidate alloys are also exposed in a small-scale coal-fired combustor at the National Energy Technology Laboratory in Pittsburgh. Experiments in the present program, which addresses the effects of deposit chemistry, temperature, and alloy chemistry on the corrosion response of alloys, were conducted at temperatures in the range of 575-800 C for time periods up to {approx}1850 h. Fe-base alloys selected for the study included HR3C, 310TaN, HR120, SAVE 25, NF709, modified 800, 347HFG, and HCM12A. In addition, 800H clad with Alloy 671 was included in several of the exposures. Ni-base alloys selected for the study included 600, 601, 617, 690, 625, 602CA, 214, 230, 45TM, HR 160, and 693. Data were obtained on weight change, scale thickness, internal penetration, microstructural characteristics of corrosion products, mechanical integrity of the scales, and cracking of scales. Results showed that the relationship of corrosion rates to temperature followed a bell-shaped curve for Fe-base alloys, with peak rates at {approx}725 C, but the rate itself was dependent on the alloy chemistry. Several Fe-base alloys showed acceptable rates in the sulfate-containing coal-ash environment; but NaCl in the deposit led to catastrophic corrosion at 650 and 800 C. Ni-base alloys generally exhibited less corrosion than the Fe-base alloys under similar exposure conditions; however, they were susceptible to localized corrosion in the form of pits.

  4. Assessment of mercury health risks to adults from coal combustion

    SciTech Connect

    Lipfert, F.W.; Moskowitz, P.D.; Fthenakis, V.M.; DePhillips, M.P.; Viren, J.; Saroff, L.

    1994-05-01

    The U.S. Environmental Protection Agency (EPA) is preparing, for the U.S. Congress, a report evaluating the need to regulate mercury (Hg) emissions from electric utilities. This study, to be completed in 1995, will have important health and economic implications. In support of these efforts, the U.S. Department of Energy, Office of Fossil Energy, sponsored a risk assessment project at Brookhaven National Laboratory (BNL) to evaluate methylmercury (MeHg) hazards independently. In the BNL study, health risks to adults resulting from Hg emissions from a hypothetical 1000 MW{sub e} coal-fired power plant were estimated using probabilistic risk assessment techniques. The approach draws on the extant knowledge in each of the important steps in the calculation chain from emissions to health effects. Estimated results at key points in the chain were compared with actual measurements to help validate the modeled estimates. Two cases were considered: the baseline case (no local impacts), and the impact case (maximum local power-plant impact). The BNL study showed that the effects of emissions of a single power plant may double the background exposures to MeHg resulting from consuming fish obtained from a localized area near the power plant. Many implicit and explicit sources of uncertainty exist in this analysis. Those that appear to be most in need of improvement include data on doses and responses for potentially sensitive subpopulations (e.g., fetal exposures). Rather than considering hypothetical situations, it would also be preferable to assess the risks associated with actual coal-fired power plants and the nearby sensitive water bodies and susceptible subpopulations. Finally, annual total Hg emissions from coal burning and from other anthropogenic sources are still uncertain; this makes it difficult to estimate the effects of U.S. coal burning on global Hg concentration levels, especially over the long term.

  5. Recent progress in the use of synchrotron radiation for the analysis of coal combustion products

    SciTech Connect

    Manowitz, B.; Kang, S.G.; Moore, J.; Helble, J.J.; Shah, N.; Huffman, G.P.

    1993-06-01

    The formation and build-up of slag deposits on heat transfer surfaces is one of the most serious problems in pulverized coal combustion. This phenomenon, traditionally called wall slagging, is known to cause undesirable effects on heat and mass transfer and in some instances induce corrosion. What is believed to be a major mechanism for the production of slag is the formation of low melting eutectic compounds in the post combustion region, many of which will stick to the heat transfer surface. The composition of this slag may very well change during operation as layers of the slaggy material build up or break off. An understanding of the chemical composition of such slags under boiler operating conditions and as a function of the mineral composition of various coals is the ultimate goal of this program. The principal constituents in the ash of many coals are the oxides of Si, Al, Fe, Ca, K, S, and Na. The analytical method required must be able to determine the functional forms of all of these elements both in coal and in coal ash at elevated temperatures. One unique way of conducting these analyses is by x-ray spectroscopy.

  6. Development and Testing of Industrial Scale Coal Fired Combustion System, Phase 3

    SciTech Connect

    Bert Zauderer

    1998-09-30

    Coal Tech Corp's mission is to develop, license & sell innovative, lowest cost, solid fuel fired power systems & total emission control processes using proprietary and patented technology for domestic and international markets. The present project 'DEVELOPMENT & TESTING OF INDUSTRIAL SCALE, COAL FIRED COMBUSTION SYSTEM, PHASE 3' on DOE Contract DE-AC22-91PC91162 was a key element in achieving this objective. The project consisted of five tasks that were divided into three phases. The first phase, 'Optimization of First Generation 20 MMBtu/hr Air-Cooled Slagging Coal Tech Combustor', consisted of three tasks, which are detailed in Appendix 'A' of this report. They were implemented in 1992 and 1993 at the first generation, 20 MMBtu/hour, combustor-boiler test site in Williamsport, PA. It consisted of substantial combustor modifications and coal-fired tests designed to improve the combustor's wall cooling, slag and ash management, automating of its operation, and correcting severe deficiencies in the coal feeding to the combustor. The need for these changes was indicated during the prior 900-hour test effort on this combustor that was conducted as part of the DOE Clean Coal Program. A combination of combustor changes, auxiliary equipment changes, sophisticated multi-dimensional combustion analysis, computer controlled automation, and series of single and double day shift tests totaling about 300 hours, either resolved these operational issues or indicated that further corrective changes were needed in the combustor design. The key result from both analyses and tests was that the combustor must be substantially lengthened to maximize combustion efficiency and sharply increase slag retention in the combustor. A measure of the success of these modifications was realized in the third phase of this project, consisting of task 5 entitled: 'Site Demonstration with the Second Generation 20 MMBtu/hr Air-Cooled Slagging Coal Tech Combustor'. The details of the task 5 effort are

  7. PAH emissions from coal combustion and waste incineration.

    PubMed

    Hsu, Wei Ting; Liu, Mei Chen; Hung, Pao Chen; Chang, Shu Hao; Chang, Moo Been

    2016-11-15

    The characteristics of PAHs that are emitted by a municipal waste incinerator (MWI) and coal-fired power plant are examined via intensive sampling. Results of flue gas sampling reveal the potential for PAH formation within the selective catalytic reduction (SCR) system of a coal-fired power plant. In the large-scale MWI, the removal efficiency of PAHs achieved with the pilot-scaled catalytic filter (CF) exceeds that achieved by activated carbon injection with a bag filter (ACI+BF) owing to the effective destruction of gas-phase contaminants by a catalyst. A significantly lower PAH concentration (1640ng/g) was measured in fly ash from a CF module than from an ACI+BF system (5650ng/g). Replacing the ACI+BF system with CF technology would significantly reduce the discharge factor (including emission and fly ash) of PAHs from 251.6 to 77.8mg/ton-waste. The emission factors of PAHs that are obtained using ACI+BF and the CF system in the MWI are 8.05 and 7.13mg/ton, respectively. However, the emission factor of MWI is significantly higher than that of coal-fired power plant (1.56mg/ton). From the perspective of total environmental management to reduce PAH emissions, replacing the original ACI+BF process with a CF system is expected to reduce environmental impact thereof. PMID:27391862

  8. Characterization of Oxy-combustion Impacts in Existing Coal-fired Boilers

    SciTech Connect

    Adams, Bradley; Davis, Kevin; Senior, Constance; Shim, Hong Shim; Otten, Brydger; Fry, Andrew; Wendt, Jost; Eddings, Eric; Paschedag, Alan; Shaddix, Christopher; Cox, William; Tree, Dale

    2013-09-30

    Reaction Engineering International (REI) managed a team of experts from University of Utah, Siemens Energy, Praxair, Vattenfall AB, Sandia National Laboratories, Brigham Young University (BYU) and Corrosion Management Ltd. to perform multi-scale experiments, coupled with mechanism development, process modeling and CFD modeling, for both applied and fundamental investigations. The primary objective of this program was to acquire data and develop tools to characterize and predict impacts of CO{sub 2} flue gas recycle and burner feed design on flame characteristics (burnout, NO{sub x}, SO{sub x}, mercury and fine particle emissions, heat transfer) and operational concerns (fouling, slagging and corrosion) inherent in the retrofit of existing coal-fired boilers for oxy-coal combustion. Experimental work was conducted at Sandia National Laboratories’ Entrained Flow Reactor, the University of Utah Industrial Combustion Research Facility, and Brigham Young University. Process modeling and computational fluid dynamics (CFD) modeling was performed at REI. Successful completion of the project objectives resulted in the following key deliverables: 1) Multi-scale test data from 0.1 kW bench-scale, 100 kW and 200 kW laboratory-scale, and 1 MW semi-industrial scale combustors that describe differences in flame characteristics, fouling, slagging and corrosion for coal combustion under air-firing and oxygen-firing conditions, including sensitivity to oxy-burner design and flue gas recycle composition. 2) Validated mechanisms developed from test data that describe fouling, slagging, waterwall corrosion, heat transfer, char burnout and sooting under coal oxy-combustion conditions. The mechanisms were presented in a form suitable for inclusion in CFD models or process models. 3) Principles to guide design of pilot-scale and full-scale coal oxy-firing systems and flue gas recycle configurations, such that boiler operational impacts from oxy-combustion retrofits are minimized. 4

  9. Ashes to earth: Coal combustion by-products returned to the mine site

    SciTech Connect

    Power, C.B.

    1997-06-01

    The use of coal in the generation of electricity has grown dramatically in the last twenty years. With increasing demand for energy and deregulation in the utility industry, there is good reason to believe that coal will play an even larger role in meeting future utility fuel needs. This increased use of coal in energy production will create larger amounts of coal combustion by-products (CCBs). Add to the equation the strict limits on power plant emissions of sulfur dioxide the nitrogen oxides brought about by the 1990 Clean Air Act Amendments- and the resultant increased use of scrubbing and other emission control methods- and it is quite possible that the quantities of CCBs will grow at an even faster rate than the increase in the use of coal. Although the list of productive uses for CCBs has expanded considerably, large amounts continue to be disposed each year. According to the American Coal Ash Association, no more than 25 percent of the 90 million tons of CCBs produced in 1994 were put to beneficial use. The remainder must be dealt with in some acceptable fashion. As of 1988, coal-fired electric utilities spent about $800 million per year doing so.

  10. Oxy-fuel combustion systems for pollution free coal fired power generation

    SciTech Connect

    Ochs, Thomas L.; Oryshchyn, Danylo B.; Gross, Dietrich; Patrick, Brian; Gross, Alex; Dogan, Cindy; Summers, Cathy A.; Simmons, William; Schoenfeld, Mark

    2004-01-01

    Jupiter Oxygen's patented oxy-fuel combustion systems1 are capable of economically generating power from coal with ultra-low emissions and increased boiler efficiency. Jupiter's system uses pure oxygen as the combustion agent, excluding air and thus nitrogen, concentrating CO2 and pollutants for efficient capture with near zero NOx production, reducing exhaust mass flow, and increasing radiant heat transfer. Flue-gas recirculation rates can be varied to add flexibility to new boiler designs using this technology. Computer modeling and thermal analysis have identified important design considerations in retrofit applications.

  11. Transformations of inorganic coal constituents in combustion systems. Volume 2, Sections 6 and 7: Final report

    SciTech Connect

    Helble, J.J.; Srinivasachar, S.; Wilemski, G.; Boni, A.A.; Kang, Shin-Gyoo; Sarofim, A.F.; Graham, K.A.; Beer, J.M.; Peterson, T.W.; Wendt, J.O.L.; Gallagher, N.B.; Bool, L.; Huggins, F.E.; Huffman, G.P.; Shah, N.; Shah, A.

    1992-11-01

    Results from an experimental investigation of the mechanisms governing the ash aerosol size segregated composition resulting from the combustion of pulverized coal in a laboratory scale down-flow combustor are described. The results of modeling activities used to interpret the results of the experiments conducted under his subtask are also described in this section. Although results from the entire program are included, Phase II studies which emphasized: (1) alkali behavior, including a study of the interrelationship between potassium vaporization and sodium vaporization; and (2) iron behavior, including an examination of the extent of iron-aluminosilicate interactions, are highlighted. Idealized combustion determination of ash particle formation and surface stickiness are also described.

  12. Optical and chemical characterization of aerosols emitted from coal, heavy and light fuel oil, and small-scale wood combustion.

    PubMed

    Frey, Anna K; Saarnio, Karri; Lamberg, Heikki; Mylläri, Fanni; Karjalainen, Panu; Teinilä, Kimmo; Carbone, Samara; Tissari, Jarkko; Niemelä, Ville; Häyrinen, Anna; Rautiainen, Jani; Kytömäki, Jorma; Artaxo, Paulo; Virkkula, Aki; Pirjola, Liisa; Rönkkö, Topi; Keskinen, Jorma; Jokiniemi, Jorma; Hillamo, Risto

    2014-01-01

    Particle emissions affect radiative forcing in the atmosphere. Therefore, it is essential to know the physical and chemical characteristics of them. This work studied the chemical, physical, and optical characteristics of particle emissions from small-scale wood combustion, coal combustion of a heating and power plant, as well as heavy and light fuel oil combustion at a district heating station. Fine particle (PM1) emissions were the highest in wood combustion with a high fraction of absorbing material. The emissions were lowest from coal combustion mostly because of efficient cleaning techniques used at the power plant. The chemical composition of aerosols from coal and oil combustion included mostly ions and trace elements with a rather low fraction of absorbing material. The single scattering albedo and aerosol forcing efficiency showed that primary particles emitted from wood combustion and some cases of oil combustion would have a clear climate warming effect even over dark earth surfaces. Instead, coal combustion particle emissions had a cooling effect. Secondary processes in the atmosphere will further change the radiative properties of these emissions but are not considered in this study. PMID:24328080

  13. Chemical evolution of Miocene wood: Example from the Belchatow brown coal deposit, central Poland

    USGS Publications Warehouse

    Drobniak, A.; Mastalerz, Maria

    2006-01-01

    Miocene conifer wood samples from the Belchatow brown coal deposit in Poland were studied in order to discuss a range of chemical variations that occur as a result of biochemical coalification. Petrographic analysis, ultimate analysis, electron microprobe technique, and FTIR spectroscopy were used in this study. Our data show several progressive trends in functional groups distribution that take place during the wood transformation from group 1 to group 4, such as an overall increase in aromaticity, an increase in lignin/cellulose ratio, and an increase in oxygen functionalities. Other observations include an increase in aliphatic stretching and bending functionalities from groups 1 to 3; followed by a decrease in the wood of group 4; appearance of aliphatic out-of-plane bands in group 3 and increase in group 4; an increase in CH2/CH3 in group 4 compared to the other groups; and decrease in O-H groups in group 4 compared to other groups. These observations, together with other chemical and petrological observations, indicate that the progressive elimination of cellulose and modification of lignin are dominant processes of the wood transformation. ?? 2005 Elsevier B.V. All rights reserved.

  14. Material and structural characterization of alkali activated low-calcium brown coal fly ash.

    PubMed

    Skvára, Frantisek; Kopecký, Lubomír; Smilauer, Vít; Bittnar, Zdenek

    2009-09-15

    The waste low-calcium Czech brown coal fly ash represents a considerable environmental burden due to the quantities produced and the potentially high content of leachable heavy metals. The heterogeneous microstucture of the geopolymer M(n) [-(Si-O)(z)-Al-O](n).wH(2)O, that forms during the alkaline activation, was examined by means of microcalorimetry, XRD, TGA, DSC, MIP, FTIR, NMR MAS ((29)Si, (27)Al, (23)Na), ESEM, EDS, and EBSD. The leaching of heavy metals and the evolution of compressive strength were also monitored. The analysis of raw fly ash identified a number of different morphologies, unequal distribution of elements, Fe-rich rim, high internal porosity, and minor crystalline phases of mullite and quartz. Microcalorimetry revealed exothermic reactions with dependence on the activator alkalinity. The activation energy of the geopolymerization process was determined as 86.2kJ/mol. The X-ray diffraction analysis revealed no additional crystalline phases associated with geopolymer formation. Over several weeks, the (29)Si NMR spectrum testified a high degree of polymerization and Al penetration into the SiO(4) tetrahedra. The (23)Na NMR MAS spectrum hypothesized that sodium is bound in the form of Na(H(2)O)(n) rather than Na(+), thus causing efflorescence in a moisture-gradient environment. As and Cr(6+) are weakly bonded in the geopolymer matrix, while excellent immobilization of Zn(2+), Cu(2+), Cd(2+), and Cr(3+) are reported. PMID:19303704

  15. Combustion and leaching behavior of elements in the argonne premium coal samples

    USGS Publications Warehouse

    Finkelman, R.B.; Palmer, C.A.; Krasnow, M.R.; Aruscavage, P. J.; Sellers, G.A.; Dulong, F.T.

    1990-01-01

    Eight Argonne Premium Coal samples and two other coal samples were used to observe the effects of combustion and leaching on 30 elements. The results were used to infer the modes of occurrence of these elements. Instrumental neutron activation analysis indicates that the effects of combustion and leaching on many elements varied markedly among the samples. As much as 90% of the selenium and bromine is volatilized from the bituminous coal samples, but substantially less is volatilized from the low-rank coals. We interpret the combustion and leaching behavior of these elements to indicate that they are associated with the organic fraction. Sodium, although nonvolatile, is ion-exchangeable in most samples, particularly in the low-rank coal samples where it is likely to be associated with the organic constituents. Potassium is primarily in an ion-exchangeable form in the Wypdak coal but is in HF-soluble phases (probably silicates) in most other samples. Cesium is in an unidentified HNO3-soluble phase in most samples. Virtually all the strontium and barium in the low-rank coal samples is removed by NH4OAc followed by HCl, indicating that these elements probably occur in both organic and inorganic phases. Most tungsten and tantalum are in insoluble phases, perhaps as oxides or in organic association. Hafnium is generally insoluble, but as much as 65% is HF soluble, perhaps due to the presence of very fine grained or metamict zircon. We interpret the leaching behavior of uranium to indicate its occurrence in chelates and its association with silicates and with zircon. Most of the rare-earth elements (REE) and thorium appear to be associated with phosphates. Differences in textural relationships may account for some of the differences in leaching behavior of the REE among samples. Zinc occurs predominantly in sphalerite. Either the remaining elements occur in several different modes of occurrence (scandium, iron), or the leaching data are equivocal (arsenic, antimony

  16. Cooperative research on the combustion characteristics of cofired desulfurized Illinois coal and char with natural gas

    SciTech Connect

    Buckius, R.O.

    1991-01-01

    Previous studies at UIUC have shown that natural gas co-firing with coal has the effect of sulfur retention in the ash, and researchers have suggested that co-firing could reduce ash deposition problems. This project will study (1) the overall sulfur retention as a function of combustion conditions (temperature, coal type, residence time, etc.), (2) the effects of types of sulfur species and sulfur transformations (pyrite, organic, sulphates, etc.) on sulfur retention, and (3) the transformation of ash constituents important to fouling (iron, magnesium, potassium, etc.). The Drop Tube Furnace Facility (DTFF) is to be used for this study.

  17. Thermochemical and trace element behavior of coal gangue, agricultural biomass and their blends during co-combustion.

    PubMed

    Zhou, Chuncai; Liu, Guijian; Cheng, Siwei; Fang, Ting; Lam, Paul Kwan Sing

    2014-08-01

    The thermal decomposition behavior of coal gangue, peanut shell, wheat straw and their blends during combustion were determined via thermogravimetric analysis. The coal gangue/agricultural biomass blends were prepared in four weight ratios and oxidized under dynamic conditions from room temperature to 1000 °C by various heating rates. Kinetic models were carried out to evaluate the thermal reactivity. The overall mass balance was performed to assess the partition behavior of coal gangue, peanut shell and their blends during combustion in a fixed bed reactor. The decomposition processes of agricultural biomass included evaporation, release of volatile matter and combustion as well as char oxidation. The thermal reactivity of coal gangue could be improved through the addition of agricultural biomass in suitable proportion and subsequent appropriate heating rate during combustion. In combination with the heating value and base/acid ratio limitations, a blending ratio of 30% agricultural biomass is conservatively selected as optimum blending. PMID:24914998

  18. High efficiency power generation from coal and wastes utilizing high temperature air combustion technology (Part 1: Performance of pebble bed gasifier for coal and wastes)

    SciTech Connect

    Kosaka, Hitoshi; Iwahashi, Takashi; Yoshida, Nobuhiro; Tsuji, Kiyoshi; Yoshikawa, Kunio; Kiga, Takashi; Tamamushi, Fumihiro; Makino, Kenji; Oonish, Hiroshi

    1998-07-01

    A new concept of a gasifier for coal and wastes is proposed where entrained bed and fixed pebble bed are combined. Main features of this pebble bed gasifier are high efficiency molten slag capture, high efficiency gasification and compactness. Coal and RFD combustion experiments using the pebble bed gasifier demonstrated high efficiency capture and continuous extraction of molten slag as well as complete char combustion with extra ordinarily short residence time of pulverized coal and crushed RDF at the temperature level of about 1,500 C within the pebble bed. Durability tests using high temperature electric furnace has shown that high density alumna is a good candidate for pebble material.

  19. NOx, FINE PARTICLE AND TOXIC METAL EMISSIONS FROM THE COMBUSTION OF SEWAGE SLUDGE/COAL MIXTURES: A SYSTEMATIC ASSESSMENT

    SciTech Connect

    Jost O.L. Wendt

    2003-06-02

    This research project focuses on pollutants from the combustion of mixtures of dried municipal sewage sludge (MSS) and coal. The objective is to determine the relationship between (1) fraction sludge in the sludge/coal mixture, and (2) combustion conditions on (a) NOx concentrations in the exhaust, (b) the size segregated fine and ultra-fine particle composition in the exhaust, and (c) the partitioning of toxic metals between vapor and condenses phases, within the process.

  20. Pressurized chemical-looping combustion of coal with an iron ore-based oxygen carrier

    SciTech Connect

    Xiao, Rui; Song, Min; Zhang, Shuai; Shen, Laihong; Song, Qilei; Lu, Zuoji

    2010-06-15

    Chemical-looping combustion (CLC) is a new combustion technology with inherent separation of CO{sub 2}. Most of the previous investigations on CLC of solid fuels were conducted under atmospheric pressure. A pressurized CLC combined cycle (PCLC-CC) system is proposed as a promising coal combustion technology with potential higher system efficiency, higher fuel conversion, and lower cost for CO{sub 2} sequestration. In this study pressurized CLC of coal with Companhia Valedo Rio Doce (CVRD) iron ore was investigated in a laboratory fixed bed reactor. CVRD iron ore particles were exposed alternately to reduction by 0.4 g of Chinese Xuzhou bituminous coal gasified with 87.2% steam/N{sub 2} mixture and oxidation with 5% O{sub 2} in N{sub 2} at 970 C. The operating pressure was varied between 0.1 MPa and 0.6 MPa. First, control experiments of steam coal gasification over quartz sand were performed. H{sub 2} and CO{sub 2} are the major components of the gasification products, and the operating pressure influences the gas composition. Higher concentrations of CO{sub 2} and lower fractions of CO, CH{sub 4}, and H{sub 2} during the reduction process with CVRD iron ore was achieved under higher pressures. The effects of pressure on the coal gasification rate in the presence of the oxygen carrier were different for pyrolysis and char gasification. The pressurized condition suppresses the initial coal pyrolysis process while it also enhances coal char gasification and reduction with iron ore in steam, and thus improves the overall reaction rate of CLC. The oxidation rates and variation of oxygen carrier conversion are higher at elevated pressures reflecting higher reduction level in the previous reduction period. Scanning electron microscope and energy-dispersive X-ray spectroscopy (SEM-EDX) analyses show that particles become porous after experiments but maintain structure and size after several cycles. Agglomeration was not observed in this study. An EDX analysis demonstrates

  1. Fireside Corrosion in Oxy-fuel Combustion of Coal

    SciTech Connect

    G. R. Holcomb; J. Tylczak; G. H. Meier; B. Lutz; K. Jung; N. Mu; N. M. Yanar; F. S. Pettit; J. Zhu; A. Wise; D. Laughlin; S. Sridhar

    2012-05-20

    Oxy-fuel combustion is burning a fuel in oxygen rather than air. The low nitrogen flue gas that results is relatively easy to capture CO{sub 2} from for reuse or sequestration. Corrosion issues associated with the environment change (replacement of much of the N{sub 2} with CO{sub 2} and higher sulfur levels) from air- to oxy-firing were examined. Alloys studied included model Fe-Cr alloys and commercial ferritic steels, austenitic steels, and nickel base superalloys. The corrosion behavior is described in terms of corrosion rates, scale morphologies, and scale/ash interactions for the different environmental conditions.

  2. Trace metal capture by various sorbents during fluidized bed coal combustion

    SciTech Connect

    Ho, T.C.; Ghebremeskel, A.; Hopper, J.R.

    1996-06-01

    Experiments were conducted in a 1-in. quartz fluidized bed combustor enclosed in an electric furnace. Coal samples were burned in the bed with a sorbent under specific combustion conditions and the amount of metal capture by the sorbent determined. Three different cao samples from the Illinois Basin Coal Sample Bank were tested. Metals involved were Cd, Pb, and Cr; the sorbents included bauxite, zeolite, and lime. Potential metal-sorbent reactions were identified. Results indicated that metal capture by sorbent can be as high as 96%, depending on the metal species and sorbent. All 3 sorbents were capable of capturing Pb, zeolite and lime were able to capture Cr, and bauxite was the only sorbent capable of capturing Cd. Thermodynamic equilibrium calculations suggested the formation of metal-sorbent compounds such as Pb{sub 2}SiO{sub 4}, CdAl{sub 2}O{sub 4}, and CdSiO{sub 3} solids under the combustion conditions.

  3. Developmemt of coal combustion sensitivity tests for smoke detectors. Report of investigations/1995

    SciTech Connect

    Edwards, J.C.; Morrow, G.S.

    1994-11-01

    Standard smoldering and flaming combustion tests using small coal samples have been developed by the U.S. Bureau of Mines as a method to evaluate the response of a smoke detector. The test provides a standard, easily reproducible smoke characteristic for coal smoldering and flaming combustion based upon a comparison of the smoke optical density and the response of a standard ionization chamber to the smoke. With these standard tests, the range of threshold limits for the response of a smoke detector and the detector`s reliability can be evaluated for nearly identical smoke visibility and smoke physical characteristics. The detector`s threshold response limits and reliability need to be well defined prior to the instrument`s use as part of a mine fire warning system for improved mine safety.

  4. USGS TOXIC SUBSTANCES FROM COAL COMBUSTION -- FORMS OF OCCURRENCE ANALYSIS

    SciTech Connect

    Allan Kolker; Stanley J. Mroczkowski; Curtis A. Palmer; Robert B. Finkelman

    1999-10-01

    Leaching procedures have been completed for the three Phase 2 coals. Chemical analyses have been returned for the whole coals, allowing leaching results to be determined as data on the leachates and solid residues become available. Problems with the nitric acid leaching step twice necessitated repeating the entire procedure for the Ohio and North Dakota samples. Similarly, leaching of the Wyodak sample was repeated once. Analytical results have been returned for all but the last complete round of leaching, which was conducted after modification of the procedure for the nitric acid step. Re-leaching of solid residues prepared under the old procedure confirms that pyrite recovery using the new method is complete. Development of an improved analytical method for Hg continues, but emphasis has shifted from the atomic fluorescence method to an automated direct analysis method that offers similar or better sensitivity. The cold vapor atomic absorption (CVAA) method has been used in the interim for whole coals. During the reporting period Dr. Kolker traveled to Stanford University to evaluate the Stanford/USGS SHRIMP-RG ion microprobe for project purposes and generate trace-element results for illite/smectite in project coals. Initial SHRIMP results for Cr in these samples confirm the Phase 1 conclusion that its concentration in clays is just below the detection limit ({approximately} 100--200 ppm) for electron microprobe analysis. The SHRIMP-RG offers promise for other project priorities, including determination of Hg in sulfides and of As in fly-ash. Use of the SEM and electron microprobe continued during the last half-year, and has been especially useful in support of the ion probe effort. Among other procedures conducted, low temperature ashing has been completed and XRD determinations are underway. Splits of leached residues have been taken for XAFS analysis. The authors expect the first of these to be determined shortly by their Univ. of Kentucky colleagues. These

  5. Chemical Fixation of CO2 in Coal Combustion Products and Recycling through Biosystems

    SciTech Connect

    C. Henry Copeland; Paul Pier; Samantha Whitehead; David Behel

    2002-09-30

    This Annual Technical Progress Report presents the principal results in enhanced growth of algae using coal combustion products as a catalyst to increase bicarbonate levels in solution. Optimal production of biomass depends on a number of factors. These factors include pH management, harvesting, and impact of auxiliary operations on the algae population. A number of experiments are presented which attempt to identify and characterize the impact of these factors.

  6. FINE PARTICAL AND TOXIC METAL EMISSIONS FROM THE COMBUSTION OF SEWAGE SLUDGE/COAL MIXTURES: A SYSTEMATIC ASSESSMENT

    SciTech Connect

    Jost O.L. Wendt; Wayne S. Seames; Art Fernandez

    2003-09-21

    This research project focuses on pollutants from the combustion of mixtures of dried municipal sewage sludge (MSS) and pulverized coal. The objective was to determine potential tradeoffs between CO{sub 2} mitigation through using a CO{sub 2} neutral fuel, such as municipal sewage sludge, and the emergence of other potential problems such as the emission of toxic fly ash particles. The work led to new insight into mechanisms governing the partitioning of major and trace metals from the combustion of sewage sludge, and mixtures of coal and sewage sludge. The research also showed that the co-combustion of coal and sewage sludge emitted fine particulate matter that might potentially cause greater lung injury than that from the combustion of either coal alone or municipal sewage sludge alone. The reason appeared to be that the toxicity measured required the presence of large amounts of both zinc and sulfur in particles that were inhaled. MSS provided the zinc while coal provided the sulfur. Additional research showed that the toxic effects could most likely be engineered out of the process, through the introduction of kaolinite sorbent downstream of the combustion zone, or removing the sulfur from the fuel. These results are consequences of applying ''Health Effects Engineering'' to this issue. Health Effects Engineering is a new discipline arising out of this work, and is derived from using a collaboration of combustion engineers and toxicologists to mitigate the potentially bad health effects from combustion of this biomass fuel.

  7. Combustion characterization of the blend of plant coal and recovered coal fines. [Quarterly] technical report, March 1, 1992--May 31, 1992

    SciTech Connect

    Singh, S.; Scaroni, A.; Miller, B.; Choudhry, V.

    1992-10-01

    The overall objective of this proposed research program is to determine the combustion characteristics of the blend derived from mixing a plant coal and recovered and clean coal fines from the pond. One plant coal and three blend samples will be prepared and utilized. The blend samples will be of a mixture of 90% plant coal + 10% fines, 85% plant coal + 15% fines, 80% plant coal + 20% fines having particle size distribution of 70% passing through -200 mesh size. These samples` combustion behavior will be examined in two different furnaces at Penn State University, i.e., a down-fired furnace and a drop-tube furnace. The down-fired furnace win be used mainly to measure the emissions and ash deposition study, while the drop tube furnace will be used to determine burning profile, combustion efficiency, etc. The burning profile of the plant coal and the three blends was determined in a thermogravimetric analyzer. Results indicated slower burning of the blends due to low volatile matter and oxidized coal particles. Ash fusing temperatures of the samples were determined using ASTM procedure. Preliminary combustion evaluation of the samples (100% plant coal, 80% plant coal/20% recovered coal fines) indicated that the flame was stable at 100,000-200,000 Btu/hr firing rate. Carbon conversion efficiency of 85 to 90% was recorded using the Ash Tracer technique. Tests are continuing to determine the operating boundaries for these blends while measuring the emissions of SO{sub x}, NO{sub x}, CO and O{sub 2}, maintaining a stable flame.

  8. [Separation of PM2.5 from coal combustion with phase change].

    PubMed

    Yan, Jin-pei; Yang, Lin-jun; Zhang, Xia; Sun, Lu-juan; Zhang, Yu; Shen, Xiang-lin

    2008-12-01

    The influence of two methods of gas moisture conditioning on removal efficiency of PM2.5 from coal combustion with addition of atomized droplets and steam was investigated. The particles size distribution and number concentration were measured in real time by electrical low pressure impactor (ELPI). The results show that collection efficiency of PM2.5 from coal combustion can be highly improved with steam condensational enlargement. Particle stage collection efficiency increases with the particles, especially for those smaller than 0.3 microm. The separation efficiency can be improved by 60% with the size of particles increasing from 0.03 microm to 0.3 microm for 0.1 kg/m3 of steam addition. The removal efficiency is independent of the gas temperature at the inlet of conditioning chamber for steam addition. But it increases with the gas temperature obviously for atomized droplets addition, which can be improved by 30% with increasing gas temperature from 136 degrees C to 256 degrees C. High removal efficiency of PM2.5 from coal combustion can be obtained with atomized droplets evaporation in hot flue gas except for steam addition. PMID:19256364

  9. Indoor air sampling and mutagenicity studies of emissions from unvented coal combustion

    SciTech Connect

    Mumford, J.L.; Harris, D.B.; Williams, K.; Chuang, J.C.; Cooke, M.

    1987-03-01

    To develop sampling strategies and bioassay protocols for indoor air containing emissions from coal combustion in homes of the rural Xuan Wei County in China, the authors developed a medium-volume sampler to collect the <10-..mu..m particles and semivolatile organics by a filter and an XAD-2 resin, respectively. A high-volume particulate sampler was used for comparison. The coal was burned under conditions that simulated the open-pit combustion that occurs in Xuan Wei. High-volume and medium-volume sampling yielded similar, high particulate concentrations 38-39 mg/m/sup 3/. Fifteen percent of the total extractable organic mass was collected in the XAD-2 resin, and the remaining 85% was retained in the filter. The polycyclic aromatic hydrocarbons found in the XAD were composed of four or fewer rings. In the Ames Salmonella assay, the XAD sample showed low mutagenic activity, and most of the mutagenic activity was found in the filter. The coal combustion emitted both direct- and indirect-acting mutagens, most of which were frameshift mutagens. 12 references, 2 figures, 3 tables.

  10. Oxy-fuel Combustion and Integrated Pollutant Removal as Retrofit Technologies for Removing CO2 from Coal Fired Power Plants

    SciTech Connect

    Ochs, T.L.; Oryshchyn, D.B.; Summers, C.A.; Gerdemann, S.J.

    2001-01-01

    One third of the US installed capacity is coal-fired, producing 49.7% of net electric generation in 20051. Any approach to curbing CO2 production must consider the installed capacity and provide a mechanism for preserving this resource while meeting CO2 reduction goals. One promising approach to both new generation and retrofit is oxy-fuel combustion. Using oxygen instead of air as the oxidizer in a boiler provides a concentrated CO2 combustion product for processing into a sequestration-ready fluid.... Post-combustion carbon capture and oxy-fuel combustion paired with a compression capture technology such as IPR are both candidates for retrofitting pc combustion plants to meet carbon emission limits. This paper will focus on oxy-fuel combustion as applied to existing coal power plants.

  11. Effects of coal combustion and gasification upon lung structure and function. Quarterly progress report, March 12, 1981

    SciTech Connect

    Not Available

    1981-01-01

    The overall objective of the proposed research is to correlate both structural and functional alterations in cells and tissues of the lung brought about by exposure to fluidized bed combustion and fixed bed gasification effluents and reagent grade oxides of metals known to be associated with coal combustion and gasification.

  12. MUTAGENICITY, CARCINOGENICITY, AND HUMAN CANCER RISK FROM INDOOR EXPOSURE TO COAL AND WOOD COMBUSTION IN XUAN WEI, CHINA

    EPA Science Inventory

    The residents in Xuan Wei County, China, have been exposed to high levels of combustion emissions from smoky and smokeless coal and wood combustion under unvented conditions in homes. n unusually high lung cancer mortality rate that can not be attributed to tobacco smoke or occup...

  13. LUNG TUMOR KRAS AND TP53 MUTATIONS IN NONSMOKERS REFLECT EXPOSURE TO PAH-RICH COAL COMBUSTION EMISSIONS

    EPA Science Inventory

    Lung Tumor KRAS and TP53 Mutations in Nonsmokers Reflect Exposure to PAH-Rich
    Coal Combustion Emissions

    Use of smoky coal in unvented homes in Xuan Wei County, Yunnan Province, China, is associated with lung cancer among nonsmoking females. Such women have the highest...

  14. Combustion of dense streams of coal particles. Quarterly progress report No. 6, November 29, 1991--February 28, 1992

    SciTech Connect

    Annamalai, K.

    1992-04-14

    Research on coal combustion continued. Activities during November 29, 1991 to February 28, 1992 includes: Further analytical results on char array combustion and internal ignition of porous char; preliminary runs using a flat flame burner have been made and a blue flat flame has been obtained; a CID camera, EPIX frame grabber and software, Sony monitor and a 486 Computer to handle image processing frame by frame have been acquired; a new coal feeder has been constructed for feeding through the flat flame burner. Coal experiments have not yet been conducted. Coal samples from Penn State Coal Bank were also acquired for use in the experiments. They include bituminous and subbituminous coals of differing VM.

  15. Application of artificial neural networks to co-combustion of hazelnut husk-lignite coal blends.

    PubMed

    Yıldız, Zeynep; Uzun, Harun; Ceylan, Selim; Topcu, Yıldıray

    2016-01-01

    The artificial neural network (ANN) theory is applied to thermal data obtained by non-isothermal thermogravimetric analysis (TGA) from room temperature to 1000°C at different heating rates in air to study co-combustion of hazelnut husk (HH)-lignite coal (LC) blends of various composition. The heating rate, blend ratio and temperature were used in the ANN analysis to predict the TG curves of the blends as parameters that affect the thermal behavior during combustion. The ANN model provides a good prediction of the TG curves for co-combustion with a coefficient of determination for the developed model of 0.9995. The agreement between the experimental data and the predicted values substantiated the accuracy of the ANN calculation. PMID:26476163

  16. Bleederless ventilation systems as a spontaneous combustion control measure in US coal mines. Information circular/1994

    SciTech Connect

    Smith, A.C.; Diamond, W.P.; Mucho, T.P.; Organiscak, J.A.

    1994-01-01

    The U.S. Bureau of Mines conducted a worldwide literature review of bleederless ventilation practices to evaluate their use as a spontaneous combustion control measure in U.S. coal mines. Factors that must be taken into account in the design and use of these systems include seal construction, the use of ventilation control devices, the use of methane-drainage systems in gassy mines, and the ground control plan. Monitoring for the detection of spontaneous combustion and the control of methane when methane-drainage techniques are employed is critical to the successful use of a bleederless ventilation system. The report describes the types of ventilation systems used throughout the world and the spontaneous combustion risks associated with these systems.

  17. Examination of bleederless ventilation practices for spontaneous combustion control in US coal mines

    SciTech Connect

    Organiscak, J.A.; Smith, A.C.; Diamond, W.P.; Mucho, T.P.

    1995-12-31

    The U.S. Bureau of Mines examined bleederless ventilation practices to evaluate their use as a spontaneous combustion control measure in U.S. coal mines. Results indicate that restricting airflow into mined-out areas (bleederless ventilation) is recognized worldwide as a spontaneous combustion control measure. However, ventilation practices commonly used to limit airflow to mined-out areas are not easily applicable to United States mining conditions, systems, experience and regulations. The types of bleederless ventilation systems used throughout the world and the spontaneous combustion risks associated with these systems are discussed. Primary design considerations for bleederless ventilation consist of the interaction of ventilation practices, methane drainage, ground control, seal construction and mine monitoring. Technological improvements needed for U.S. application of bleederless ventilation are also discussed.

  18. Combustion of ultrafine coal/water mixtures and their application in gas turbines: Final report

    SciTech Connect

    Toqan, M.A.; Srinivasachar, S.; Staudt, J.; Varela, F.; Beer, J.M.

    1987-10-01

    The feasibility of using coal-water fuels (CWF) in gas turbine combustors has been demonstrated in recent pilot plant experiments. The demands of burning coal-water fuels with high flame stability, complete combustion, low NO/sub x/ emission and a resulting fly ash particle size that will not erode turbine blades represent a significant challenge to combustion scientists and engineers. The satisfactory solution of these problems requires that the variation of the structure of CWF flames, i.e., the fields of flow, temperature and chemical species concentration in the flame, with operating conditions is known. Detailed in-flame measurements are difficult at elevated pressures and it has been proposed to carry out such experiments at atmospheric pressure and interpret the data by means of models for gas turbine combustor conditions. The research was carried out in five sequential tasks: cold flow studies; studies of conventional fine-grind CWF; combustion studies with ultrafine CWF fuel; reduction of NO/sub x/ emission by staged combustion; and data interpretation-ignition and radiation aspects. 37 refs., 61 figs., 9 tabs.

  19. Determination of halogens in coal after digestion using the microwave-induced combustion technique

    SciTech Connect

    Flores, E.M.M.; Mesko, M.F.; Moraes, D.P.; Pereira, J.S.F.; Mello, P.A.; Barin, J.S.; Knapp, G.

    2008-03-15

    The microwave-induced combustion (MIC) technique was applied for coal digestion and further determination of bromide, chloride, fluoride, and iodide by ion chromatography (IC). Samples (up to 500 mg) were combusted at 2 MPa of oxygen. Combustion was complete in less than 50 s, and analytes were absorbed in water or (NH{sub 4}){sub 2}CO{sub 3} solution. A reflux step was applied to improve analyte absorption. Accuracy was evaluated for Br, Cl, and F using certified reference coal and spiked samples for I. For Br, Cl, and F, the agreement was between 96 and 103% using 50 mmol L{sup -1} (NH{sub 4}){sub 2}CO{sub 3} as the absorbing solution and 5 min of reflux. With the use of the same conditions, the recoveries for I were better than 97%. Br, Cl, and I were also determined in MIC digests by inductively coupled plasma mass spectrometry, inductively coupled plasma optical emission spectrometry, and F was determined by an ion-selective electrode with agreement better than 95% to the values obtained using IC. Temperature during combustion was higher than 1350 {sup o}C, and the residual carbon content was lower than 1%. With the use of the MIC technique, up to eight samples could be processed simultaneously, and a single absorbing solution was suitable for all analytes and determination techniques (limit of detection by IC was better than 3 {mu} g g{sup -1} for all halogens).

  20. Fireside Corrosion in Oxy-fuel Combustion of Coal

    SciTech Connect

    Holcomb, Gordon R; Tylczak, Joseph; Meier, Gerald H; Lutz, Bradley; Jung, Keeyoung; Mu, Nan; Yanar, Nazik M; Pettit, Frederick S; Zhu, Jingxi; Wise, Adam; Laughlin, David E.; Sridhar, Seetharaman

    2013-11-25

    Oxy-fuel combustion is burning a fuel in oxygen rather than air for ease of capture of CO2 from for reuse or sequestration. Corrosion issues associated with the environment change (replacement of much of the N2 with CO2 and higher sulfur levels) from air- to oxy-firing were examined. Alloys studied included model Fe–Cr alloys and commercial ferritic steels, austenitic steels, and nickel base superalloys. The corrosion behavior is described in terms of corrosion rates, scale morphologies, and scale/ash interactions for the different environmental conditions. Evidence was found for a hreshold for severe attack between 10-4 and 10-3 atm of SO3 at 700ºC.

  1. Carbon-Centered Free Radicals in Particulate Matter Emissions from Wood and Coal Combustion

    PubMed Central

    2009-01-01

    Electron paramagnetic resonance (EPR) spectroscopy was used to measure the free radicals in the particulate matter (PM) emissions from wood and coal combustion. The intensity of radicals in PM dropped linearly within two months of sample storage and stabilized after that. This factor of storage time was adjusted when comparing radical intensities among different PM samples. An inverse relationship between coal rank and free radical intensities in PM emissions was observed, which was in contrast with the pattern of radical intensities in the source coals. The strong correlation between intensities of free radical and elemental carbon in PM emissions suggests that the radical species may be carbon-centered. The increased g-factors, 2.0029−2.0039, over that of purely carbon-centered radicals may indicate the presence of vicinal oxygen heteroatom. The redox and biology activities of these carbon-centered radicals are worthy of evaluation. PMID:19551161

  2. Gel retarder for fire prevention and extinguishing -- Its application for spontaneous combustion of coal seams

    SciTech Connect

    1998-12-31

    With its unique function, gel retarder has been successfully applied to extinguish fire at coal face, roadways and stop line of upper slice extraction, and a comparably perfect set of fire extinguishing techniques has been developed. The technique gathers together characteristics of water-fixation, leak-blocking, cooling, oxidation-retarding and heat-resisting. A new agglomerating agent without amine and corrosion has been developed to replace amine-salt and acid used in the past. Gel-injection technology cooperating with the grouting system on the ground solves previous problems in which gel-injection velocity was slow and materials transport was difficult. The technique has become the main measure to extinguish spontaneous combustion in coal mines in China. The use of gel retarder as an important means of underground fire prevention will be applied more widely to prevent and extinguish spontaneous fire in coal mines.

  3. Application of model-free methods for analysis of combustion kinetics of coals with different ranks

    SciTech Connect

    Sis, H

    2009-07-01

    Model-free kinetic approaches were employed to investigate the combustion kinetics of coals with different ranks, namely, lignite, bituminous coal, and anthracite. The experimental data were provided under non-isothermal conditions at different heating rates in the range of 2-25C min{sup -1}. The activation energy values were estimated by two model-free methods, that is, Ozawa-Flynn-Wall and Kissinger-Akahira-Sunose methods. Slightly higher activation energy values were obtained by Ozawa-Flynn-Wall method at a wide range of conversion extent. Variation of activation energy was found to be comparably more significant for lower rank lignite (between 44.82 and 287.56 kJ mol{sup -1}) while less significant for higher rank bituminous coal (between 101.97 and 155.64 kJ mol{sup -1}) and anthracite (between 106.04 and 160.31 kJ mol{sup -1}).

  4. Progression in sulfur isotopic compositions from coal to fly ash: Examples from single-source combustion in Indiana

    USGS Publications Warehouse

    Yaofa, Jiang; Elswick, E.R.; Mastalerz, Maria

    2008-01-01

    Sulfur occurs in multiple mineral forms in coals, and its fate in coal combustion is still not well understood. The sulfur isotopic composition of coal from two coal mines in Indiana and fly ash from two power plants that use these coals were studied using geological and geochemical methods. The two coal beds are Middle Pennsylvanian in age; one seam is the low-sulfur ( 5%) Springfield Coal Member of the Petersburg Formation. Both seams have ash contents of approximately 11%. Fly-ash samples were collected at various points in the ash-collection system in the two plants. The results show notable difference in ??34S for sulfur species within and between the low-sulfur and high-sulfur coal. The ??34S values for all sulfur species are exclusively positive in the low-sulfur Danville coal, whereas the ??34S values for sulfate, pyritic, and organic sulfur are both positive and negative in the high-sulfur Springfield coal. Each coal exhibits a distinct pattern of stratigraphic variation in sulfur isotopic composition. Overall, the ??34S for sulfur species values increase up the section in the low-sulfur Danville coal, whereas they show a decrease up the vertical section in the high-sulfur Springfield coal. Based on the evolution of ??34S for sulfur species, it is suggested that there was influence of seawater on peat swamp, with two marine incursions occurring during peat accumulation of the high-sulfur Springfield coal. Therefore, bacterial sulfate reduction played a key role in converting sulfate into hydrogen sulfide, sulfide minerals, and elemental sulfur. The differences in ??34S between sulfate sulfur and pyritic sulfur is very small between individual benches of both coals, implying that some oxidation occurred during deposition or postdeposition. The ??34S values for fly ash from the high-sulfur Springfield coal (averaging 9.7???) are greatly enriched in 34S relative to those in the parent coal (averaging 2.2???). This indicates a fractionation of sulfur isotopes

  5. Control of trace metal emissions during coal combustion. Technical progress report, October 1, 1995--December 31, 1995

    SciTech Connect

    Ho, Thomas C.

    1996-01-01

    Emissions of toxic trace metals in the form of metal fumes or submicron particulates from a coal-fired combustion source have received greater environmental and regulatory concern over the past years. Current practice of controlling these emissions is to collect them at the cold end of the process by air-pollution control devices such as electrostatic precipitators and baghouses. However, trace metal fumes may not always be effectively collected by these devices because the formed fumes are extremely small. The proposed research is to explore the opportunities for improved control of toxic trace metal emissions at the hot end of the coal combustion process, i.e., in the combustion chamber. The technology proposed is to prevent the metal fumes from forming during the process. Specifically, the technology is to employ suitable sorbents to reduce the amount of metal volatilization during combustion and capture volatized metal vapors. The objectives of this project are to demonstrate the technology and to characterize the metal capture process during coal combustion in a fluidized bed combustor. The following progress has been made during the performance period from Oct. 1, 1995 through Dec. 31, 1995: (1) Additional combustion experiments involving both coal and wood pellets were carried out in the constructed quartz fluidized bed combustor. (2) A new Buck Scientific Model 210VGP Atomic Absorption spectrophotometer equipped with a continuous flow hydride generator especially for arsenic and selenium was installed for the project. (3) A paper, entitled ``Capture of Toxic Metals by Various Sorbents during Fluidized Bed Coal Combustion,`` was presented at the 1995 AIChE Annual Meeting held in Miami, November 13--17, 1995. (4) A manuscript, entitled ``Trace Metal Capture by Various Sorbents during Fluidized Bed Coal Combustion,`` was submitted to the 26th International Symposium on Combustion for presentation and for publication in the symposium proceedings. 1 ref., 3 tabs.

  6. A diffusion-kinetic model for pulverized-coal combustion and heat-and-mass transfer in a gas stream

    SciTech Connect

    E.A. Boiko; S.V. Pachkovskii

    2008-12-15

    A diffusion-kinetic model for pulverized-coal combustion and heat-and-mass transfer in a gas stream is proposed, and the results of numerical simulation of the burnout dynamics of Kansk-Achinsk coals in the pulverized state at different treatment conditions and different model parameters are presented. The mathematical model describes the dynamics of thermochemical conversion of solid organic fuels with allowance for complex physicochemical phenomena of heat-and-mass exchange between coal particles and the gaseous environment.

  7. Further investigation of the impact of the co-combustion of tire-derived fuel and petroleum coke on the petrology and chemistry of coal combustion products

    SciTech Connect

    Hower, J.C.; Robertson, J.D.; Elswick, E.R.; Roberts, J.M.; Brandsteder, K.; Trimble, A.S.; Mardon, S.M.

    2007-07-01

    A Kentucky cyclone-fired unit burns coal and tire-derived fuel, sometimes in combination with petroleum coke. A parallel pulverized combustion (pc) unit at the same plant burns the same coal, without the added fuels. The petrology, chemistry, and sulfur isotope distribution in the fuel and resulting combustion products was investigated for several configurations of the fuel blend. Zinc and Cd in the combustion products are primarily contributed from the tire-derived fuel, the V and Ni are primarily from the petroleum coke, and the As and Hg are probably largely from the coal. The sulfur isotope distribution in the cyclone unit is complicated due to the varying fuel sources. The electrostatic precipitator (ESP) array in the pc unit shows a subtle trend towards heavier S isotopic ratios in the cooler end of the ESP.

  8. Toxic Substances from Coal Combustion: A Comprehensive Assessment: Quarterly report, 1 July 1996-30 September 1996

    SciTech Connect

    Bool, L.E.; Senior, C.L.; Huggins, F.; Huffman, G.P.; Shah, N.; Wendt, J.O.L.; Peterson, T.W.; Sarofim, A.F.; Olmez, I.; Zeng, T.; Crowley, S.; Finkelman, R.

    1996-10-01

    The Clean Air Act Amendments of 1990 identify a number of hazardous air pollutants (HAPS) as candidates for regulation. Should regulations be imposed on HAP emissions from coal-fired power plants, a sound understanding of the fundamental principles controlling the formation and partitioning of toxic species during coal combustion will be needed. With support from the Pittsburgh Energy Technology Center (PETC), the Electric Power Research Institute (EPRI), and VTT (Finland), Physical Sciences Inc. (PSI) has teamed with researchers from USGS, MIT, the University of Arizona (UA), the University of Kentucky (UKy), the University of Connecticut, and Princeton University to develop a broadly applicable emissions model useful to regulators and utility planners. The new Toxics Partitioning Engineering Model (ToPEM) will be applicable to all combustion conditions including new fuels and coal blends, low-NO{sub x}, combustion systems, and new power generation plants. Development of ToPEM will be based on PSI`s existing Engineering Model for Ash Formation (EMAF). Extensive coal characterization and laboratory work has begun in order to develop and test new sub-models. Trace element concentrations in the Pittsburgh, Elkhorn/Hazard, and Illinois No. 6 coals, and in size/density fractions of these coals, were completed. Coal characterization in the past quarter also included direct identification of the modes of occurrence of various trace inorganic species in coal and ash using unique analytical techniques such as XAFS analysis and selective leaching. Combustion testing of these two coals was begun and preliminary data obtained on trace element 0301 vaporization in the combustion zone. Modeling efforts in the past quarter include the development on a preliminary model to assess mercury speciation in combustion systems.

  9. The study of partitioning of heavy metals during fluidized bed combustion of sewage sludge and coal

    SciTech Connect

    Gulyurtlu, I.; Lopes, M.H.; Abelha, P.; Cabrita, I.; Oliveira, J.F.S.

    2006-06-15

    The behavior of Cd, Cr, Cu, Co, Mn, Ni, Pb, Zn, and Hg during the combustion tests of a dry granular sewage sludge on a fluidized bed combustor pilot (FBC) of about 0.3 MW was evaluated. The emissions of these heavy metals from mono-combustion were compared with those of co-combustion of the sludge with a bituminous coal. The effect of the addition of limestone was also studied in order to retain sulphur compounds and to verify its influence on the retention of heavy metals (HM). Heavy metals were collected and analyzed from different locations of the installation, which included the stack, the two cyclones, and the material removed from the bed. The results showed that the volatility of metals was rather low, resulting in emissions below the legal limits of the new directive on incineration, with the exception of Hg during the mono-combustion tests. The partitioning of metals, except for Hg, appeared to follow that of ashes, amounting to levels above 90% in the bed streams in the mono-combustion case. For co-combustion, there was a lower fixation of HM in the bed ashes, mostly originating essentially from the sewage sludge, ranging between 40% and 80%. It is believed that in this latter case, a slightly higher temperature could have enhanced the volatilization, especially of Cd and Pb. However these metals were then retained in fly ashes captured in the cyclones. In the case of Hg, the volatilisation was complete. The bed ashes were free of Hg and part of Hg was retained in the cyclones and the rest was emitted either with fine ash particles or in gaseous forms. In mono-combustion the Hg emissions from the stack (particles and gas) accounted, for about 50%. This appeared to have significantly decreased in the case of co-combustion, as only about 75% has been emitted, due to the retention effect of cyclone ashes.

  10. CO2 adsorption properties of char produced from brown coal impregnated with alcohol amine solutions.

    PubMed

    Baran, Paweł; Zarębska, Katarzyna; Czuma, Natalia

    2016-07-01

    Carbon dioxide (CO2) emission reduction is critical to mitigating climate change. Power plants for heating and industry are significant sources of CO2 emissions. There is a need for identifying and developing new, efficient methods to reduce CO2 emissions. One of the methods used is flue gas purification by CO2 capture through adsorption. This study aimed to develop CO2 adsorbent out of modified brown coal impregnated with solutions of first-, second-, and third-order amines. Low-temperature nitrogen adsorption isotherms and CO2 isotherms were measured for the prepared samples. The results of experiments unexpectedly revealed that CO2 sorption capacity decreased after impregnation. Due to lack of strait trends in CO2 sorption capacity decrease, the results were closely analyzed to find the reason for the inconsistencies. It was revealed that different amines represent different affinities for CO2 and that the size and structure of impregnating factor has influence on the CO2 sorption capacity of impregnated material. The character of a support was also noticeable as well for impregnation results as for the affinity to CO2. The influence of amine concentration used was investigated along with the comparison on how the theoretical percentage of the impregnation on the support influenced the results. The reaction mechanism of tertiary amine was taken into consideration in connection to no presence of water vapor during the experiments. Key findings were described in the work and provide a strong basis for further studies on CO2 adsorption on amine-impregnated support. PMID:27317051

  11. Reduction of metal leaching in brown coal fly ash using geopolymers.

    PubMed

    Bankowski, P; Zou, L; Hodges, R

    2004-10-18

    Current regulations classify fly ash as a prescribed waste and prohibit its disposal in regular landfill. Treatment of the fly ash can reduce the leach rate of metals, and allow it to be disposed in less prescribed landfill. A geopolymer matrix was investigated as a potential stabilisation method for brown coal fly ash. Precipitator fly ash was obtained from electrostatic precipitators and leached fly ash was collected from ash disposal ponds, and leaching tests were conducted on both types of geopolymer stabilised fly ashes. The ratio of fly ash to geopolymer was varied to determine the effects of different compositions on leaching rates. Fourteen metals and heavy metals were targeted during the leaching tests and the results indicate that a geopolymer is effective at reducing the leach rates of many metals from the fly ash, such as calcium, arsenic, selenium, strontium and barium. The major element leachate concentrations obtained from leached fly ash were in general lower than that of precipitator fly ash. Conversely, heavy metal leachate concentrations were lower in precipitator fly ash than leached pond fly ash. The maximum addition of fly ash to this geopolymer was found to be 60wt% for fly ash obtained from the electrostatic precipitators and 70wt% for fly ash obtained from ash disposal ponds. The formation of geopolymer in the presence of fly ash was studied using 29Si MAS-NMR and showed that a geopolymer matrix was formed. X-ray diffraction (XRD) analysis and scanning electron microscopy (SEM) imaging showed the interaction of the fly ash with the geopolymer, which was related to the leachate data and also the maximum percentage fly ash addition. PMID:15511575

  12. Partitioning of selected trace elements in coal combustion products from two coal-burning power plants in the United States

    USGS Publications Warehouse

    Swanson, Sharon M.; Engle, Mark A.; Ruppert, Leslie F.; Affolter, Ronald H.; Jones, Kevin B.

    2013-01-01

    Samples of feed coal (FC), bottom ash (BA), economizer fly ash (EFA), and fly ash (FA) were collected from power plants in the Central Appalachian basin and Colorado Plateau to determine the partitioning of As, Cr, Hg, Pb, and Se in coal combustion products (CCPs). The Appalachian plant burns a high-sulfur (about 3.9 wt.%) bituminous coal from the Upper Pennsylvanian Pittsburgh coal bed and operates with electrostatic precipitators (ESPs), with flue gas temperatures of about 163 °C in the ESPs. At this plant, As, Pb, Hg, and Se have the greatest median concentrations in FA samples, compared to BA and EFA. A mass balance (not including the FGD process) suggests that the following percentages of trace elements are captured in FA: As (48%), Cr (58%), Pb (54%), Se (20%), and Hg (2%). The relatively high temperatures of the flue gas in the ESPs and low amounts of unburned C in FA (0.5% loss-on-ignition for FA) may have led to the low amount of Hg captured in FA. The Colorado Plateau plant burns a blend of three low-S (about 0.74 wt.%) bituminous coals from the Upper Cretaceous Fruitland Formation and operates with fabric filters (FFs). Flue gas temperatures in the baghouses are about 104 °C. The elements As, Cr, Pb, Hg, and Se have the greatest median concentrations in the fine-grained fly ash product (FAP) produced by cyclone separators, compared to the other CCPs at this plant. The median concentration of Hg in FA (0.0983 ppm) at the Colorado Plateau plant is significantly higher than that for the Appalachian plant (0.0315 ppm); this higher concentration is related to the efficiency of FFs in Hg capture, the relatively low temperatures of flue gas in the baghouses (particularly in downstream compartments), and the amount of unburned C in FA (0.29% loss-on-ignition for FA).

  13. Mutagenicity, carcinogenicity, and human cancer risk from indoor exposure to coal and wood combustion in xuan wei, china

    SciTech Connect

    Mumford, J.L.; Chapman, R.S.; Nesnow, S.; Helmes, C.T.; Li, X.

    1990-01-01

    The residents in Xuan Wei County, China, have been exposed to high levels of combustion emissions from smoky and smokeless coal and wood combustion under unvented conditions in homes. An unusually high lung cancer mortality rate that can not be attributed to tobacco smoke or occupational exposure was found. The communes using smoky coal, which emits more organics than smokeless coal, generally have a higher lung cancer rate than the communes using smokeless coal or wood. The mutagenicity and carcinogenicity of organic extracts of indoor air particles collected from Xuan Wei homes during cooking were investigated. The objectives of the study were (1) to investigate the characteristics of lung cancer mortality in Xuan Wei, (2) to determine the genotoxicity and chemical and physical properties of the combustion emissions, and (3) to link bioassay results to human lung cancer data. The organic extracts of these emission particles were tested for mutagenicity in the Ames Salmonella and the L5178Y TK+/- mouse lymphoma assays and for skin tumor-initiating activity and complete carcinogenicity in SENCAR mice. The two coal samples showed higher activity in both mutagenicity and tumor initiation. When the emission rate of organics was taken into consideration, the smoky coal emission showed the highest potency of the three fuels. The smoky coal sample was also a more potent complete carcinogen than the wood sample. Higher mutagenicity and carcinogenicity of the smoky coal emission compared to wood or smokeless coal emissions are in agreement with the epidemiological data.

  14. Conversion of the trace elements Zn, Cd, and Pb in the combustion of near-Moscow coals

    SciTech Connect

    E.V. Samuilov; L.N. Lebedeva; L.S. Pokrovskaya; M.V. Faminskaya

    2008-10-15

    A model for the conversion of trace elements in the combustion of near-Moscow coals based on a complex approach combining the capabilities of geochemistry, chemical thermodynamics, phase analysis, and chemical kinetics is proposed. The conversion of the trace elements Zn, Cd, and Pb as the constituents of near-Moscow coal in the flow of coal combustion products along the line of the P-59 boiler at the Ryazanskaya Thermal Power Plant was calculated. Experimental data were used in the development of the model and in calculations.

  15. Experimental study on the minimum ignition temperature of coal dust clouds in oxy-fuel combustion atmospheres.

    PubMed

    Wu, Dejian; Norman, Frederik; Verplaetsen, Filip; Van den Bulck, Eric

    2016-04-15

    BAM furnace apparatus tests were conducted to investigate the minimum ignition temperature of coal dusts (MITC) in O2/CO2 atmospheres with an O2 mole fraction from 20 to 50%. Three coal dusts: Indonesian Sebuku coal, Pittsburgh No.8 coal and South African coal were tested. Experimental results showed that the dust explosion risk increases significantly with increasing O2 mole fraction by reducing the minimum ignition temperature for the three tested coal dust clouds dramatically (even by 100°C). Compared with conventional combustion, the inhibiting effect of CO2 was found to be comparatively large in dust clouds, particularly for the coal dusts with high volatile content. The retardation effect of the moisture content on the ignition of dust clouds was also found to be pronounced. In addition, a modified steady-state mathematical model based on heterogeneous reaction was proposed to interpret the observed experimental phenomena and to estimate the ignition mechanism of coal dust clouds under minimum ignition temperature conditions. The analysis revealed that heterogeneous ignition dominates the ignition mechanism for sub-/bituminous coal dusts under minimum ignition temperature conditions, but the decrease of coal maturity facilitates homogeneous ignition. These results improve our understanding of the ignition behaviour and the explosion risk of coal dust clouds in oxy-fuel combustion atmospheres. PMID:26799218

  16. Overlapping of heterogeneous and purely thermally activated solid-state processes in the combustion of a bituminous coal

    SciTech Connect

    Senneca, Osvalda; Salatino, Piero

    2006-02-01

    Mechanistic studies of coal combustion have long highlighted the variety of reaction pathways along which gasification may take place. These involve chemisorption of reactants, formation of surface oxides, surface mobility of chemisorbed species, and product desorption. At the same time, exposure of the solid fuel to high temperatures is associated with solid-state thermally activated processes. Altogether, the course of gasification may be profoundly affected by the overlapping and interplay of heterogeneous oxidation with purely thermally activated solid-state reactions. In the present work the combustion of a South African bituminous coal is analyzed in the framework of a simplified reaction network that embodies heterogeneous oxidative and thermally activated processes (pyrolysis, thermal annealing, coal combustion, char combustion, oxygen chemisorption) active both on the raw coal and on its char. The kinetics of each process of the network is assessed by a combination of thermogravimetric and gas analysis on coal and char samples. The analysis is directed to the determination of the prevailing combustion pathway, established from the interplay of oxidative and solid-state thermally activated processes, as a function of combustion conditions (temperature, heating rate, particle size). (author)

  17. Combustion of dense streams of coal particles. Quarterly progress report No. 9, August 29, 1992--November 28, 1992

    SciTech Connect

    Annamalai, K.

    1992-12-31

    Ignition of the high volatile isolated coal particles in vitiated environment seems to occur heterogeneously at the leading edge of the particle. Volatiles are observed to be ejected upward as jets in the direction of the convective flow but only after heterogeneous ignition. The volatiles burn in the gas phase homogeneously and form a wake flame; a black inner zone (unburned volatile) is formed (see Fig.A.3 for many common characteristics of isolated flames).Intermittent volatile ignition and combustion are observed to occur during the combustion process for a few of the isolated particle combustion experiments on high volatile non-swelling coal. The medium volatile coal particles ignite faster than the high volatile coal; but the intermittent ignition is not observed. The low volatile isolated coal particles combust in shorter time. The isolated char particles ignite at the surface of the particle heterogeneously with little volatile ejected, yet are not sufficient to form a volatile flame, resulting in a subsequent heterogeneous combustion. A group flame is formed for the two-particle arrays at closer interparticle spacing (Fig.A.4). Also, intermittent ignition does not occur for the high volatile particles when the two particles are at farther distances which suggests that radiation interaction between the particles might be occurring. However this conclusion is purely speculative. The char arrays experience heterogeneous ignition at the leading edge; combustion proceeds heterogeneously.

  18. NOx, FINE PARTICLE AND TOXIC METAL EMISSIONS FROM THE COMBUSTION OF SEWAGE SLUDGE/COAL MIXTURES: A SYSTEMATIC ASSESSMENT

    SciTech Connect

    Jost O.L. Wendt

    2001-08-01

    This research project focuses on pollutants from the combustion of mixtures of dried municipal sewage sludge (MSS) and coal. The objective is to determine the relationship between (1) fraction sludge in the sludge/coal mixture, and (2) combustion conditions on (a) NOx concentrations in the exhaust, (b) the size segregated fine and ultra-fine particle composition in the exhaust, and (c) the partitioning of toxic metals between vapor and condenses phases, within the process. To this end work is progress using an existing 17kW downflow laboratory combustor, available with coal and sludge feed capabilities. The proposed study will be conducted in concert with an existing ongoing research on toxic metal partitioning mechanisms for very well characterized pulverized coals alone. Both high NOx and low NOx combustion conditions will be investigated (unstaged and staged combustion). The proposed work uses existing analytical and experimental facilities and draws on 20 years of research on NO{sub x} and fine particles that has been funded by DOE in this laboratory. Four barrels of dried sewage sludge are currently in the laboratory. Insofar as possible pertinent mechanisms will be elucidated. Tradeoffs between CO{sub 2} control, NO{sub x} control, and inorganic fine particle and toxic metal emissions will be determined. For the Third Quarter of this project we present our data on trace metal partitioning obtained from combustion of MSS and Gas, MSS and Coal and Coal and Gas alone.

  19. Evaluation of fly ash from co-combustion of coal and petroleum coke for use in concrete

    SciTech Connect

    Scott, A.N.; Thomas, M.D.A.

    2007-01-15

    An investigation of fly ash (FA) produced from various blends of coal and petroleum coke (pet coke) fired at Belledune Generating Station, New Brunswick, Canada, was conducted to establish its performance relative to FA derived from coal-only combustion and its compliance with CSA A3000. The FA samples were beneficiated by an electrostatic separation process to produce samples for testing with a range of loss-on-ignition (LOI) values. The results of these studies indicate that the combustion of pet coke results in very little inorganic residue (for example, typically less than 0.5% ash) and the main impact on FA resulting from the co-combustion of coal and up to 25% pet coke is an increase in the unburned carbon content and LOI values. The testing of FA after beneficiation indicates that FA produced from fuels with up to 25% pet coke performs as good as FA produced from the same coal without pet coke.

  20. A coal-fired combustion system for industrial process heating applications

    SciTech Connect

    Not Available

    1992-09-03

    PETC has implemented a number of advanced combustion research projects that will lead to the establishment of a broad, commercially acceptable engineering data base for the advancement of coal as the fuel of choice for boilers, furnaces, and process heaters. Vortec Corporation's Phase III development contract DE-AC22-91PC91161 for a Coal-Fired Combustion System for Industrial Process Heating Applications'' is project funded under the DOE/PETC advanced combustion program. This advanced combustion system research program is for the development of innovative coal-fired process heaters which can be used for high temperature melting, smelling and waste vitrification processes. The process heater concepts to be developed are based on advanced glass melting and ore smelting furnaces developed and patented by Vortec Corporation. The process heater systems to be developed have multiple use applications; however, the Phase III research effort is being focused on the development of a process heater system to be used for producing value added vitrified glass products from boiler/incinerator ashes and industrial wastes. The primary objective of the Phase III project is to develop and integrate all the system components, from fuel through total system controls, and then test the complete system in order to evaluate its potential marketability. During the current reporting period, approval of Vortec's Environmental Assessment (EA) required under the National Environmental Policy Act (NEPA) was approved. The EA approval cycle took approximately 9 months. The preliminary test program which was being held in abeyance pending approval of the EA was initiated. Six preliminary test runs were successfully competed during the period. Engineering and design activities in support of the Phase III proof of concept are continuing, and modifications to the existing test system configuration to allow performance of the preliminary tests were completed.