Science.gov

Sample records for carbon stripper foils

  1. Producing carbon stripper foils containing boron

    SciTech Connect

    Stoner, J. O. Jr.

    2012-12-19

    Parameters being actively tested by the accelerator community for the purpose of extending carbon stripper foil lifetimes in fast ion beams include methods of deposition, parting agents, mounting techniques, support (fork) materials, and inclusion of alloying elements, particularly boron. Specialized production apparatus is required for either sequential deposition or co-deposition of boron in carbon foils. A dual-use vacuum evaporator for arc evaporation of carbon and electron-beam evaporation of boron and other materials has been built for such development. Production of both carbon and boron foils has begun and improvements are in progress.

  2. Carbon stripper foils for heavy-ion accelerators

    SciTech Connect

    Thomas, G.E.

    1980-01-01

    Carbon stripper foils have for many years been successfully used with accelerators because they yield higher average charge states than gas strippers. However, with the development of heavy ion accelerators and the resulting use of heavier ions, the carbon stripper foil lifetimes are greatly reduced. Even when using the new foils changer systems, which typically contain two hundred foils or more, it becomes necessary to have frequent accelerator shutdowns for foil reloading. The rate of experiment interruption makes it clear a new approach is necessary to increase foil lifetimes. Several techniques have been tried with varying degrees of success to strengthen these foils so that they will last longer; the most successful one reported a lifetime increase of the order of a factor of 30 over foils produced in the conventional manner. Methods of producing various types of foils will be presented, a discussion will be given on theories for foil breakage, and some new ideas will be introduced for further increasing foil lifetimes.

  3. Carbon stripper foils used in the Los Alamos PSR

    SciTech Connect

    Borden, M.J.; Plum, M.A.; Sugai, I.

    1997-12-01

    Carbon stripper foils produced by the modified controlled ACDC arc discharge method (mCADAD) at the Institute for Nuclear Study have been tested and used for high current 800-MeV beam production in the Proton Storage Ring (PSR) since 1993. Two foils approximately 110 {mu}g/cm{sup 2} each are sandwiched together to produce an equivalent 220 {mu}g/cm{sup 2} foil. The foil sandwitch is supported by 4-5 {mu}m diameter carbon filters attached to an aluminum frame. These foils have survived as long as five months during PSR normal beam production of near 70 {mu}A average current on target. Typical life-times of other foils vary from seven to fourteen days with lower on-target average current. Beam loss data also indicate that these foils have slower shrinkage rates than standard foils. Equipment has been assembled and used to produce foils by the mCADAD method at Los Alamos. These foils will be tested during 1997 operation.

  4. Development of the carbon foils as charge strippers for high-intensity uranium ion beams

    NASA Astrophysics Data System (ADS)

    Hasebe, Hiroo; Kuboki, Hironori; Okuno, Hiroki; Fukunishi, Nobuhisa; Kamigaito, Osamu; Imao, Hiroshi; Goto, Akira; Kase, Masayuki

    2011-11-01

    carbon foil (C-foil) is commonly used as a charge stripper in the heavy-ion accelerators. Since 2005, the polymer-coated carbon foils (PCC-foils) have been fabricated at Nishina Center to prepare larger and thicker C-foils than those previously used as charge strippers. However, the multi-layer PCC-foils did not have sufficiently long life-time. Since August 2009, a new magnetron sputtering system is used to fabricate a thick C-foil. The foils coated with polymer are used as strippers. Life-times of the new single-layer PCC-foils under the uranium beam were measured in two configurations: at the first one a small piece of C-foil was attached to a fixed holder and in the second one a large C-foil was attached to a "rotating-cylinder stripper" device. The properties of the new single-layer PCC-foils and the results of the life-time measurements are reported in this contribution.

  5. Lifetime dependence of nitrided carbon stripper foils on sputter angle during N+ ion beam sputtering

    NASA Astrophysics Data System (ADS)

    Sugai, I.; Oyaizu, M.; Takeda, Y.; Kawakami, H.; Kawasaki, K.; Hattori, T.; Kadono, T.

    2015-09-01

    We fabricated high-lifetime thin nitride carbon stripper (NCS) foils with high nitrogen contents using ion-beam sputtering with reactive nitrogen gas and investigated the dependence of their lifetimes on the sputter angle. The nitrogen in carbon foils plays a critical role in determining their lifetime. Therefore, in order to investigate the effects of the nitrogen level in NCS foils on foil lifetime, we measured the sputtering yield for different sputter angles at a sputtering voltage of 10 kV while using carbon-based targets. We also measured the nitrogen-to-carbon thickness ratios of the foils using Rutherford backscattering spectrometry. The foils made at a sputter angle of 15° using a glassy amorphous carbon target exhibited an average increase of 200-fold in lifetime when compared to commercially available foils.

  6. Mounting stripper foils on forks for maximum lifetime

    NASA Astrophysics Data System (ADS)

    Jolivet, Connie S.; Stoner, John O.

    2008-06-01

    While research and development continue to produce forms of carbon for longer lasting stripper foils, relatively little attention has been paid to other factors that affect their survival in use. It becomes apparent that the form of carbon is only part of the issue. Specific mounting methods increase the lifetimes of carbon stripper foils. These methods are determined in part by the specific use and carbon type for a foil. With careful handling, appropriate adhesive, and slack mounting, premature breakage can be avoided. Foil lifetimes are then primarily affected by less easily controlled factors such as high-temperature expansion, shrinkage and evaporation.

  7. Measurement of 181 MeV H- ions stripping cross-sections by carbon stripper foil

    NASA Astrophysics Data System (ADS)

    Saha, P. K.; Yoshimoto, M.; Yamazaki, Y.; Hotchi, H.; Harada, H.; Okabe, K.; Kinsho, M.; Irie, Y.

    2015-03-01

    The stripping cross-sections of 181 MeV H- (negative hydrogen) ions by the carbon stripper foil are measured with good accuracy. The present experiment was carried out at the 3-GeV RCS (Rapid Cycling Synchrotron) of J-PARC (Japan Proton Accelerator Research Complex). The stripping cross-sections for different charge states, also known as electron loss cross-sections of H- ion, are denoted as σ-11, σ-10 and σ01, for both electrons stripping (H- →H+), one-electron stripping (H- →H0) and the 2nd-electron stripping (H0 →H+) proceeding σ-10, respectively. We have established very unique and precise techniques for such measurements so as also to determine a foil stripping efficiency very accurately. The cross-sections σ-11, σ-10 and σ01 are obtained to be (0.002 ± 0.001) ×10-18cm2, (1.580 ± 0.034) ×10-18cm2 and (0.648 ± 0.014) ×10-18cm2, respectively. The presently given cross-sections are newly available experimental results for an incident H- energy below 200 MeV and they are also shown to be consistent with recently proposed energy (1 /β2) scaled cross-sections calculated from the previously measured data at 200 and 800 MeV. The present results have a great importance not only at J-PARC for the upgraded H- beam energy of 400 MeV but also for many new and upgrading similar accelerators, where H- beam energies in most cases are considered to be lower than 200 MeV.

  8. Low-z gas stripper as an alternative to carbon foils for the acceleration of high-power uranium beams

    SciTech Connect

    Okuno, H.; Hershcovitch, A.; Fukunishi, N.; Goto, A.; Hasebe, H.; Imao, H.; Kamigaito, O.; Kase, M.; Kuboki, H.; Yano, Y.; Yokouchi, S.

    2011-04-23

    The RIKEN accelerator complex started feeding the next-generation exotic beam facility radioisotope beam factory (RIBF) with heavy-ion beams from 2007 after the successful commissioning of RIBF at the end of 2006. Many improvements made from 2007 to 2010 were instrumental in increasing the intensity of various heavy-ion beams. However, the available beam intensity of very heavy ion beams, especially uranium beams, is far below our goal of 1 p{mu}A (6 x 10{sup 12} particles/s). In order to achieve this goal, upgrade programs are already in progress; the programs include the construction of a new 28-GHz superconducting electron cyclotron resonance ion source and a new injector linac. However, the most serious problem, that of a charge stripper for high-power uranium beams, still remains unsolved, despite extensive research and development work using large foils mounted on a rotating cylinder and a N{sup 2} gas stripper. A gas stripper is free from problems related to lifetime, though the equilibrium charge state in this stripper is considerably lower than that in a carbon foil, owing to the absence of the density effect. Nevertheless, the merits of gas strippers motivated us to develop a low-Z gas stripper to achieve a higher equilibrium charge state even in gases. We measured the electron-loss and electron-capture cross sections of uranium ions in He gas as a function of their charge state at 11, 14, and 15 MeV/nucleon. The equilibrium charge states extracted from the intersection of the lines of the two cross sections were promisingly higher than those in N{sub 2} gas by more than 10. Simple simulations of charge development along the stripper thickness were performed by assuming the measured cross sections. The simulation results show that about 1 mg/cm{sup 2} of He gas should be accumulated to achieve a charge state higher than that of N{sub 2} gas, notwithstanding the difficulty in accumulation of this helium amount owing to its fast dispersion. However, we now

  9. Low-Z gas stripper as an alternative to carbon foils for the acceleration of high-power uranium beams

    NASA Astrophysics Data System (ADS)

    Okuno, H.; Fukunishi, N.; Goto, A.; Hasebe, H.; Imao, H.; Kamigaito, O.; Kase, M.; Kuboki, H.; Yano, Y.; Yokouchi, S.; Hershcovitch, A.

    2011-03-01

    The RIKEN accelerator complex started feeding the next-generation exotic beam facility radioisotope beam factory (RIBF) with heavy-ion beams from 2007 after the successful commissioning of RIBF at the end of 2006. Many improvements made from 2007 to 2010 were instrumental in increasing the intensity of various heavy-ion beams. However, the available beam intensity of very heavy ion beams, especially uranium beams, is far below our goal of 1pμA (6×1012particles/s). In order to achieve this goal, upgrade programs are already in progress; the programs include the construction of a new 28-GHz superconducting electron cyclotron resonance ion source and a new injector linac. However, the most serious problem, that of a charge stripper for high-power uranium beams, still remains unsolved, despite extensive research and development work using large foils mounted on a rotating cylinder and a N2 gas stripper. A gas stripper is free from problems related to lifetime, though the equilibrium charge state in this stripper is considerably lower than that in a carbon foil, owing to the absence of the density effect. Nevertheless, the merits of gas strippers motivated us to develop a low-Z gas stripper to achieve a higher equilibrium charge state even in gases. We measured the electron-loss and electron-capture cross sections of uranium ions in He gas as a function of their charge state at 11, 14, and 15MeV/nucleon. The equilibrium charge states extracted from the intersection of the lines of the two cross sections were promisingly higher than those in N2 gas by more than 10. Simple simulations of charge development along the stripper thickness were performed by assuming the measured cross sections. The simulation results show that about 1mg/cm2 of He gas should be accumulated to achieve a charge state higher than that of N2 gas, notwithstanding the difficulty in accumulation of this helium amount owing to its fast dispersion. However, we now believe that the following two

  10. Comparison of carbon stripper foils under operational conditions at the Los Alamos proton storage ring

    SciTech Connect

    Spickerman, Thomas; Borden, Michael J; Macek, Robert J; Sugai, Isao

    2008-01-01

    At the 39{sup th} ICFA Advanced Beam Dynamics Workshop HB 2006 and the 23{sup rd} INTDS World Conference we reported on first results of a test of nanocrystalline diamond foils developed at ORNL under operational conditions at the Los Alamos Proton Storage Ring (PSR). We have continued these tests during the 2006 and 2007 run cycles and have been able to compare the diamond foils with the foils that are normally in use in PSR, which were originally developed by Sugai at KEK. We have gathered valuable information regarding foil lifetime, foil related beam losses and electron emission at the foil. Additional insight was gained under unusual beam conditions where the foiIs are subjected to higher temperatures. In the 2007 run cycle we also tested a Diamond-like-Carbon foil developed at TRIUMF. A Hybrid-Boron-Carbon foil, also developed by Sugai, is presently in use with the PSR production beam. We will summarize our experience with these different foil types.

  11. Development of long-lived thick carbon stripper foils for high energy heavy ion accelerators by a heavy ion beam sputtering method

    NASA Astrophysics Data System (ADS)

    Muto, Hideshi; Ohshiro, Yukimitsu; Kawasaki, Katsunori; Oyaizu, Michihiro; Hattori, Toshiyuki

    2013-04-01

    In the past decade, we have developed extremely long-lived carbon stripper foils of 1-50 μg/cm2 thickness prepared by a heavy ion beam sputtering method. These foils were mainly used for low energy heavy ion beams. Recently, high energy negative Hydrogen and heavy ion accelerators have started to use carbon stripper foils of over 100 μg/cm2 in thickness. However, the heavy ion beam sputtering method was unsuccessful in production of foils thicker than about 50 μg/cm2 because of the collapse of carbon particle build-up from substrates during the sputtering process. The reproduction probability of the foils was less than 25%, and most of them had surface defects. However, these defects were successfully eliminated by introducing higher beam energies of sputtering ions and a substrate heater during the sputtering process. In this report we describe a highly reproducible method for making thick carbon stripper foils by a heavy ion beam sputtering with a Krypton ion beam.

  12. Development of long-lived thick carbon stripper foils for high energy heavy ion accelerators by a heavy ion beam sputtering method

    SciTech Connect

    Muto, Hideshi; Ohshiro, Yukimitsu; Kawasaki, Katsunori; Oyaizu, Michihiro; Hattori, Toshiyuki

    2013-04-19

    In the past decade, we have developed extremely long-lived carbon stripper foils of 1-50 {mu}g/cm{sup 2} thickness prepared by a heavy ion beam sputtering method. These foils were mainly used for low energy heavy ion beams. Recently, high energy negative Hydrogen and heavy ion accelerators have started to use carbon stripper foils of over 100 {mu}g/cm{sup 2} in thickness. However, the heavy ion beam sputtering method was unsuccessful in production of foils thicker than about 50 {mu}g/cm{sup 2} because of the collapse of carbon particle build-up from substrates during the sputtering process. The reproduction probability of the foils was less than 25%, and most of them had surface defects. However, these defects were successfully eliminated by introducing higher beam energies of sputtering ions and a substrate heater during the sputtering process. In this report we describe a highly reproducible method for making thick carbon stripper foils by a heavy ion beam sputtering with a Krypton ion beam.

  13. Performance characteristics of HBC stripper foils irradiated by 650 keV H- and high intensity DC ion beams

    NASA Astrophysics Data System (ADS)

    Sugai, I.; Takagi, A.; Takeda, Y.; Irie, Y.; Oyaizu, M.; Kawakami, H.

    2014-06-01

    Newly developed Hybrid type Boron mixed Carbon (HBC) stripper foils are extensively used not only for the RCS of J-PARC and PSR of LANL, but also for other low energy, high intensity proton accelerators in medical applications. We had before tested HBC stripper foils with 3.2 MeV Ne+ and DC heavy ion beams. In order to further understand characteristics of HBC stripper foils, we measured the following parameters using the KEK-650 keV H- and light ion Cockcroft Walton DC accelerator: foil lifetime, thickness reduction, uniformity before and after beam irradiation, and foil deformation. Energy deposition in the present experiment was adjusted to a similar level to that of the HBC foil used in the RCS of J-PARC’. In addition, to understand the reason why the HBC stripper foils have high durability against high intensity beam irradiation, we investigated various physical properties, and compared them between the HBC foils and other tested carbon stripper foils. The sizes of the carbon particles in the HBC foil were found to play a vital role in the lifetime.

  14. SNS STRIPPER FOIL FAILURE MODES AND THEIR CURES

    SciTech Connect

    Galambos, John D; Luck, Chris; Plum, Michael A; Shaw, Robert W; Ladd, Peter; Raparia, Deepak; Macek, Robert James; Kim, Sang-Ho; Peters, Charles C; Polsky, Yarom

    2010-01-01

    The diamond stripper foils in use at the Spallation Neutron Source worked successfully with no failures until May 3, 2009, when we started experiencing a rash of foil system failures after increasing the beam power to ~840 kW. The main contributors to the failures are thought to be 1) convoy electrons, stripped from the incoming H beam, that strike the foil bracket and may also reflect back from the electron catcher, and 2) vacuum breakdown from the charge developed on the foil by secondary electron emission. In this paper we will detail these and other failure mechanisms, and describe the improvements we have made to mitigate them.

  15. Spallation Neutron Source SNS Diamond Stripper Foil Development

    SciTech Connect

    Shaw, Robert W; Plum, Michael A; Wilson, Leslie L; Feigerle, Charles S.; Borden, Michael J.; Irie, Y.; Sugai, I; Takagi, A

    2007-01-01

    Diamond stripping foils are under development for the SNS. Freestanding, flat 300 to 500 {micro}g/cm{sup 2} foils as large as 17 x 25 mm{sup 2} have been prepared. These nano-textured polycrystalline foils are grown by microwave plasma-assisted chemical vapor deposition in a corrugated format to maintain their flatness. They are mechanically supported on a single edge by a residual portion of their silicon growth substrate; fine foil supporting wires are not required for diamond foils. Six foils were mounted on the SNS foil changer in early 2006 and have performed well in commissioning experiments at reduced operating power. A diamond foil was used during a recent experiment where 15 {micro}C of protons, approximately 64% of the design value, were stored in the ring. A few diamond foils have been tested at LANSCE/PSR, where one foil was in service for a period of five months (820 C of integrated injected charge) before it was replaced. Diamond foils have also been tested in Japan at KEK (640 keV H{sup -}) where their lifetimes slightly surpassed those of evaporated carbon foils, but fell short of those for Sugai's new hybrid boron carbon (HBC) foils.

  16. Stripper-foil scan studies of the first-turn beam loss mechanism in the LAMPF proton storage ring (PSR)

    SciTech Connect

    Hutson, R.: Fitzgerald, D.; Frankle, S.; Macek, R.; Plum, M.; Wilkinson, C.

    1993-01-01

    First-turn beam losses in the LAMPF Proton Storage Ring were measured as a function of the left-right position of the carbon foil used to strip neutral hydrogen atoms to H[sup +] for proton injection into the PSR. Two foil thicknesses, 200 and 300 [mu]g/cm[sup 2], were tested. Results indicated that first-turn loss is caused predominately by magnetic field stripping of a small fraction of the H[sub 0] atoms that pass through the stripper foil without being stripped to protons, and the results were not consistent with a mechanism involving protons originating from atoms in the halo of the neutral beam incident on the stripper foil.

  17. Stripper-foil scan studies of the first-turn beam loss mechanism in the LAMPF proton storage ring (PSR)

    SciTech Connect

    Hutson, R.: Fitzgerald, D.; Frankle, S.; Macek, R.; Plum, M.; Wilkinson, C.

    1993-06-01

    First-turn beam losses in the LAMPF Proton Storage Ring were measured as a function of the left-right position of the carbon foil used to strip neutral hydrogen atoms to H{sup +} for proton injection into the PSR. Two foil thicknesses, 200 and 300 {mu}g/cm{sup 2}, were tested. Results indicated that first-turn loss is caused predominately by magnetic field stripping of a small fraction of the H{sub 0} atoms that pass through the stripper foil without being stripped to protons, and the results were not consistent with a mechanism involving protons originating from atoms in the halo of the neutral beam incident on the stripper foil.

  18. Development of carbon foils with a thickness of up to 600 μg/cm 2

    NASA Astrophysics Data System (ADS)

    Kindler, Birgit; Hartmann, Willi; Hübner, Annett; Lommel, Bettina; Steiner, Jutta

    2010-02-01

    Carbon foils are applied as stripper for the heavy-ion accelerator as well as targets in different experiments at GSI. Carbon foils in a thickness range 5-100 μg/cm 2 are routinely produced with good homogeneity and excellent durability. Foils thicker than 100 μg/cm 2 used to be purchased. To overcome problems that emerged and intensified in some applications we started to advance our own carbon production towards higher thickness. We describe the production of carbon foils up to a thickness of 600 μg/cm 2, report on first tests as stripper foils and as targets, and discuss our future plans.

  19. Stripper foil failure modes and cures at the Oak Ridge Spallation Neutron Source

    NASA Astrophysics Data System (ADS)

    Plum, M. A.; Cousineau, S. M.; Galambos, J.; Kim, S. H.; Ladd, P.; Luck, C. F.; Peters, C. C.; Polsky, Y.; Shaw, R. W.; Macek, R. J.; Raparia, D.

    2011-03-01

    The Oak Ridge Spallation Neutron Source comprises a 1 GeV, 1.5 MW linear accelerator followed by an accumulator ring and a liquid mercury target. To manage the beam loss caused by the H0 excited states created during the H- charge-exchange injection into the accumulator ring, the stripper foil is located inside one of the chicane dipoles. This has some interesting consequences that were not fully appreciated until the beam power reached about 840 kW. One consequence was sudden failure of the stripper foil system due to convoy electrons stripped from the incoming H- beam, which circled around to strike the foil bracket and cause bracket failure. Another consequence is that convoy electrons can reflect back up from the electron catcher and strike the foil and bracket. An additional contributor to foil system failure is vacuum breakdown due to the charge developed on the foil by secondary electron emission. In this paper we detail these and other interesting failure mechanisms and describe the improvements we have made to mitigate them.

  20. Stripper foil failure modes and cures at the Oak Rdige Spallation Neutron Source

    SciTech Connect

    Plum, M.A.; Raparia, D.; Cousineau, S.M.; Galambos, J.; Kim, S.H.; Ladd, P.; Luck, C.F.; Peters, C.C.; Polsky, Y.; Shaw, R.W.; Macek, R.J.

    2011-03-28

    The Oak Ridge Spallation Neutron Source comprises a 1 GeV, 1.5 MW linear accelerator followed by an accumulator ring and a liquid mercury target. To manage the beam loss caused by the H{sup 0} excited states created during the H{sup -} charge-exchange injection into the accumulator ring, the stripper foil is located inside one of the chicane dipoles. This has some interesting consequences that were not fully appreciated until the beam power reached about 840 kW. One consequence was sudden failure of the stripper foil system due to convoy electrons stripped from the incoming H{sup -} beam, which circled around to strike the foil bracket and cause bracket failure. Another consequence is that convoy electrons can reflect back up from the electron catcher and strike the foil and bracket. An additional contributor to foil system failure is vacuum breakdown due to the charge developed on the foil by secondary electron emission. In this paper we detail these and other interesting failure mechanisms and describe the improvements we have made to mitigate them.

  1. Stripper foil failure modes and cures at the Spallation Neutron Source

    SciTech Connect

    Cousineau, Sarah M; Galambos, John D; Kim, Sang-Ho; Ladd, Peter; Luck, Chris; Peters, Charles C; Polsky, Yarom; Shaw, Robert W; Raparia, Deepak; Macek, Robert James; Plum, Michael A

    2011-01-01

    The Spallation Neutron Source comprises a 1 GeV, 1.4 MW linear accelerator followed by an accumulator ring and a liquid mercury target. To manage the beam loss caused by the $H^0$ excited states created during the $H^-$ charge exchange injection into the accumulator ring, the stripper foil is located inside one of the chicane dipoles. This has some interesting consequences that were not fully appreciated until the beam power reached about 840 kW. One consequence was sudden failure of the stripper foil system due to convoy electrons stripped from the incoming $H^-$ beam, which circled around to strike the foil bracket and cause bracket failure. Another consequence is that convoy electrons can reflect back up from the electron catcher and strike the foil and bracket. An additional contributor to foil system failure is vacuum breakdown due to the charge developed on the foil by secondary electron emission. In this paper we detail these and other interesting failure mechanisms and describe the improvements we have made to mitigate them.

  2. A new possibility of low-Z gas stripper for high power uranium beam acceleration alternative to C-foil

    SciTech Connect

    Okuno, H.; Hershcovitch, A.; Fukunishi, N.; Goto, A.; Hasebe, H.; Imao, H.; Kamigaito, O.; Kase, M.; Kuboki, H.; Yano, Y.

    2010-09-27

    The RIKEN accelerator complex started feeding the next-generation exotic beam facility RIBF (RadioIsotope Beam Factory) with heavy ion beams from 2007 after the successful commissioning at the end of 2006. Many elaborating improvements increased the intensity of the various heavy ion beams from 2007 to 2010. However, the available beam intensity especially of uranium beam is far below our goal of 1 p{micro}A (6 x 10{sup 12} particle/s). In order to achieve it, upgrade programs are well in progress, including constructions of a new 28 GHz superconducting ECR ion source and a new injector linac. However, the most serious problem of the charge stripper for uranium beam is still open although many elaborating R&D works for the problems. Equilibrium charge state in gas generally is much lower than that in carbon foil due to its density-effect. But gas stripper is free from the problems originated from its lifetime and uniformity in thickness. Such merits pushed us think about low-Z gas stripper to get higher equilibrium charge state even in gas. Electron loss and capture cross section of U ion beams in He gas were measured as a function of their charge state at 11, 14 and 15 MeV/u. The extracted equilibrium charge states from the cross point of the two lines of the cross sections were promisingly higher than those in N{sub 2} gas by more than 10. The plasma window is expected to be a key technology to solve the difficulty in accumulation of such thick as about 1 mg/cm{sup 2} of low-Z gas.

  3. Electric fields, electron production, and electron motion at the stripper foil in the Los Alamos Proton Storage Ring

    SciTech Connect

    Plum, M.

    1995-05-01

    The beam instability at the Los Alamos Proton Storage Ring (PSR) most likely involves coupled oscillations between electrons and protons. For this instability to occur, there must be a strong source of electrons. Investigation of the various sources of electrons in the PSR had begun. Copious electron production is expected in the injection section because this section contains the stripper foil. This foil is mounted near the center of the beam pipe, and both circulating and injected protons pass through it, thus allowing ample opportunity for electron production. This paper discusses various mechanisms for electron production, beam-induced electric fields, and electron motion in the vicinity of the foil.

  4. Carbon foils for space plasma instrumentation

    NASA Astrophysics Data System (ADS)

    Allegrini, F.; Ebert, R. W.; Funsten, H. O.

    2016-05-01

    Carbon foils have been successfully used for several decades in space plasma instruments to detect ions and neutral atoms. These instruments take advantage of two properties of the particle-foil interaction: charge conversion of neutral atoms and/or secondary electron emission. This interaction also creates several adverse effects for the projectile exiting the foil, such as angular scattering and energy straggling, which usually act to reduce the sensitivity and overall performance of an instrument. The magnitude of these effects mainly varies with the incident angle, energy, and mass of the incoming projectile and the foil thickness. In this paper, we describe these effects and the properties of the interaction. We also summarize results from recent studies with graphene foils, which can be made thinner than carbon foils due to their superior strength. Graphene foils may soon replace carbon foils in space plasma instruments and open new opportunities for space research in the future.

  5. Efficiency and lifetime of carbon foils

    SciTech Connect

    Chou, W.; Kostin, M.; Tang, Z.; /Fermilab

    2006-11-01

    Charge-exchange injection by means of carbon foils is a widely used method in accelerators. This paper discusses two critical issues concerning the use of carbon foils: efficiency and lifetime. An energy scaling of stripping efficiency was suggested and compared with measurements. Several factors that determine the foil lifetime--energy deposition, heating, stress and buckling--were studied by using the simulation codes MARS and ANSYS.

  6. Influence and efficiency of catalytic stripper in organic carbon removal from laboratory generated soot aerosols

    EPA Science Inventory

    A catalytic stripper (CS) is a device used to remove the semi-volatile, typically organic carbon, fraction by passing raw or diluted exhaust over an oxidation catalyst heated to 300˚C. The oxidation catalyst used in this study is a commercially available diesel oxidation ca...

  7. Carbon nanotube foils for electron stripping in tandem accelerators

    NASA Astrophysics Data System (ADS)

    von Reden, Karl; Zhang, Mei; Meigs, Martha; Sichel, Enid; Fang, Shaoli; Baughman, Ray H.

    2007-08-01

    Carbon nanotube technology has rapidly advanced in recent years, making it possible to create meter-long, ∼4 cm wide films of multi-walled tubes of less than 3 μg/cm2 areal density in a bench top open-air procedure. The physical properties of individual carbon nanotubes have been well established, equaling or surpassing electrical and thermal conductivity and mechanical strength of most other materials, graphite in particular. The handling and transport of such nanotube films, dry-mounted self-supporting on metal frames with several cm2 of open area, is problem-free: the aerogel films having a volumetric density of about 1.5 mg/cm3 survived the trip by car and air from Dallas to Oak Ridge without blemish. In this paper we will present the results of first tests of these nanotube films as electron stripper media in a tandem accelerator. The tests were performed in the Model 25 URC tandem accelerator of the Holifield radioactive ion beam facility (HRIBF) at Oak Ridge National Laboratory. We will discuss the performance of nanotube films in comparison with chemical vapor deposition and laser-ablated carbon foils.

  8. Relativistic Electron Transport Through Carbon Foils

    NASA Astrophysics Data System (ADS)

    Seliger, M.; Takasi, K.; Reinhold, C. O.; Takabayashi, Y.; Ito, T.; Komaki, K.; Azuma, T.; Yamazaki, Y.; Yamazaki, Y.

    We present a theoretical study of convoy electron emission resulting from transmission of relativistic 390 MeV/amu Ar17+ ions through carbon foils of various thicknesses. Our approach is based on a Langevin equation describing the random walk of the electron initially bound to the argon nucleus and later in the continuum. The calculated spectra of ejected electrons in the forward direction exhibit clear signatures of multiple scattering and are found to be in good agreement with recent experimental data.

  9. Three-dimensional thermal simulations of thin solid carbon foils for charge stripping of high current uranium ion beams at a proposed new heavy-ion linac at GSI

    NASA Astrophysics Data System (ADS)

    Tahir, N. A.; Kim, V.; Schlitt, B.; Barth, W.; Groening, L.; Lomonosov, I. V.; Piriz, A. R.; Stöhlker, Th.; Vormann, H.

    2014-04-01

    This paper presents an extensive numerical study of heating of thin solid carbon foils by 1.4 MeV/u uranium ion beams to explore the possibility of using such a target as a charge stripper at the proposed new Gesellschaft für Schwerionenforschung high energy heavy-ion linac. These simulations have been carried out using a sophisticated 3D computer code that accounts for physical phenomena that are important in this problem. A variety of beam and target parameters have been considered. The results suggest that within the considered parameter range, the target will be severely damaged by the beam. Thus, a carbon foil stripper does not seem to be a reliable option for the future Gesellschaft für Schwerionenforschung high energy heavy-ion linac, in particular, at FAIR design beam intensities.

  10. Carbon-Fiber/Epoxy Tube Lined With Aluminum Foil

    NASA Technical Reports Server (NTRS)

    Gernet, Nelson J.; Kerr, Gregory K.

    1995-01-01

    Carbon-fiber/epoxy composite tube lined with welded aluminum foil useful as part of lightweight heat pipe in which working fluid ammonia. Aluminum liner provides impermeability for vacuum seal, to contain ammonia in heat pipe, and to prevent flow of noncondensable gases into heat pipe. Similar composite-material tubes lined with foils also incorporated into radiators, single- and two-phase thermal buses, tanks for storage of cryogenic materials, and other plumbing required to be lightweight.

  11. Beam Loss due to Foil Scattering in the SNS Accumulator Ring

    SciTech Connect

    Holmes, Jeffrey A; Plum, Michael A

    2012-01-01

    In order to better understand the contribution of scattering from the primary stripper foil to losses in the SNS ring, we have carried out calculations using the ORBIT Code aimed at evaluating these losses. These calculations indicate that the probability of beam loss within one turn following a foil hit is ~1.8 10-8 , where is the foil thickness in g/cm2, assuming a carbon foil. Thus, for a typical SNS stripper foil of thickness = 390 g/cm2, the probability of loss within one turn of a foil hit is ~7.0 10-6. This note describes the calculations used to arrive at this result, presents the distribution of these losses around the SNS ring, and compares the calculated results with observed ring losses for a well-tuned production beam.

  12. Charge stripping of U238 ion beam by helium gas stripper

    NASA Astrophysics Data System (ADS)

    Imao, H.; Okuno, H.; Kuboki, H.; Yokouchi, S.; Fukunishi, N.; Kamigaito, O.; Hasebe, H.; Watanabe, T.; Watanabe, Y.; Kase, M.; Yano, Y.

    2012-12-01

    Development of a nondestructive, efficient electric-charge-stripping method is a key requirement for next-generation high-intensity heavy-ion accelerators such as the RIKEN Radioactive-Isotope Beam Factory. A charge stripper employing a low-Z gas is an important candidate applicable to high-intensity uranium beams for replacing carbon-foil strippers. In this study, a high-beam-transmission charge-stripping system employing helium gas for U238 beams injected at 10.8MeV/u was developed and demonstrated for the first time. The charge-state evolution measured using helium in a thickness range of 0.24-1.83mg/cm2 is compared with theoretical predictions. Energy attenuation and energy spread due to the helium stripper are also investigated.

  13. Electron Strippers for Compact Neutron Generators

    SciTech Connect

    Terai, K.; Tanaka, N.; Kisaki, M.; Tsugawa, K.; Okamoto, A.; Kitajima, S.; Sasao, M.; Takeno, T.; Antolak, A. J.; Leung, K. N.; Wada, M.

    2011-09-26

    The next generation of compact tandem-type DD or DT neutron generators requires a robust electron stripper with high charge exchange efficiency. In this study, stripping foils of various types were tested, and the H{sup -} to H{sup +} conversion efficiency, endurance to the heat load, and durability were investigated in terms of suitability in the tandem-type neutron generator. In the experiments, a H{sup -} beam was accelerated to about 180 keV, passes through a stripping foil, and produces a mixed beam of H{sup -}, H{sup 0}, and H{sup +}. These ions were separated by an electric field, and detected by a movable Faraday cup to determine the conversion efficiency. The experimental results using thin foils of diamond-like carbon, gold, and carbon nano-tubes revealed issues on the robustness. As a new concept, a H{sup -} beam was injected onto a metal surface with an oblique angle, and reflected H{sup +} ions are detected. It was found that the conversion efficiency, H{sup +} fraction in the reflected particles, depends on the surface condition, with the maximum value of about 90%.

  14. Characterization and anticorrosion properties of carbon nanotubes directly synthesized on Ni foil using ethanol

    NASA Astrophysics Data System (ADS)

    Jeong, Namjo; Jwa, Eunjin; Kim, Chansoo; Hwang, Kyo Sik; Park, Soon-cheol; Jang, Moon Suk

    2016-07-01

    In this work, we describe the direct growth of carbon nanofilaments by the catalytic decomposition of ethanol on untreated polycrystalline Ni foil. Our work focuses on the effects of synthesis conditions on the growth of the carbon nanofilaments and their growth mechanism. Direct growth of carbon nanotubes (CNTs) is more favorable on lower-purity Ni foil. The highest yield was obtained at approximately 750 °C. The average diameter of the CNTs was approximately 20-30 nm. Raman spectra revealed that the increase of H2 concentration in the carrier gas and synthesis temperature induced the growth of better-graphitized CNTs. Additionally, we investigated the anticorrosion properties of as-prepared products under simulated seawater conditions. The corrosion rate of the CNT/Ni foil system was maximally 50-60 times slower than that of the as-received Ni foil, indicating that the CNT coating may be a good candidate for corrosion inhibition.

  15. Mechanical design and vibro-acoustic testing of ultrathin carbon foils for a spacecraft instrument

    SciTech Connect

    Bernardin, John D; Baca, Allen G

    2009-01-01

    IBEX-Hi is an electrostatic analyzer spacecraft instrument designed to measure the energy and flux distribution of energetic neutral atoms (ENAs) emanating from the interaction zone between the Earth's solar system and the Milky Way galaxy. A key element to this electro-optic instrument is an array of fourteen carbon foils that are used to ionize the ENAs. The foils are comprised of an ultrathin (50-100 {angstrom} thick) layer of carbon suspended across the surface of an electroformed Nickel wire screen, which in turn is held taught by a metal frame holder. The electro formed orthogonal screen has square wire elements, 12.7 {micro}m thick, with a pitch of 131.1 wires/cm. Each foil holder has an open aperture approximately 5 cm by 2.5 cm. Designing and implementing foil holders with such a large surface area has not been attempted for spaceflight in the past and has proven to be extremely challenging. The delicate carbon foils are subject to fatigue failure from the large acoustic and vibration loads that they will be exposed to during launch of the spacecraft. This paper describes the evolution of the foil holder design from previous space instrument applications to a flight-like IBEX-Hi prototype. Vibro-acoustic qualification tests of the IBEX-Hi prototype instrument and the resulting failure of several foils are summarized. This is followed by a discussion of iterative foil holder design modifications and laser vibrometer modal testing to support future fatigue failure analyses, along with additional acoustic testing of the IBEX-Hi prototype instrument. The results of these design and testing activities are merged and the resulting flight-like foil holder assembly is proposed.

  16. Carbon/graphene foils: a critical subsystem for plasma instruments in space

    NASA Astrophysics Data System (ADS)

    Allegrini, F.; Ebert, R. W.; Fuselier, S. A.; Bedworth, P.; Sinton, S.

    2015-12-01

    Thin carbon foils play a critical role in the time-of-flight (TOF) and charge conversion subsystems used in many of the plasma sensors developed for space. These instruments take advantage of properties of the particle-foil interaction: charge conversion of neutral atoms and/or secondary electron emission. This interaction also creates several adverse effects for the projectile exiting the foil, such as angular scattering and energy straggling, that usually act to reduce the sensitivity and overall performance of an instrument. The magnitude of these effects varies with the incident angle, energy, and mass of the incoming projectile and the foil thickness. The thinnest foils flown typically have a nominal thickness (as specified by the manufacturer) of ~0.5 - 1 µg cm-2. In this presentation, we will summarize several studies that have quantified the properties of ions exiting the thin carbon foil and discuss recent work on graphene foils, a promising new technology that may be capable of mitigating the undesirable effects associated with these interactions.

  17. Eutectic bonding of a Ti sputter coated, carbon aerogel wafer to a Ni foil

    SciTech Connect

    Jankowski, A.F.; Hayes, J.P.; Kanna, R.L.

    1994-06-01

    The formation of high energy density, storage devices is achievable using composite material systems. Alternate layering of carbon aerogel wafers and Ni foils with rnicroporous separators is a prospective composite for capacitor applications. An inherent problem exists to form a physical bond between Ni and the porous carbon wafer. The bonding process must be limited to temperatures less than 1000{degrees}C, at which point the aerogel begins to degrade. The advantage of a low temperature eutectic in the Ni-Ti alloy system solves this problem. Ti, a carbide former, is readily adherent as a sputter deposited thin film onto the carbon wafer. A vacuum bonding process is then used to join the Ni foil and Ti coating through eutectic phase formation. The parameters required for successfld bonding are described along with a structural characterization of the Ni foil-carbon aerogel wafer interface.

  18. Vertically aligned carbon nanotube emitter on metal foil for medical X-ray imaging.

    PubMed

    Ryu, Je Hwang; Kim, Wan Sun; Lee, Seung Ho; Eom, Young Ju; Park, Hun Kuk; Park, Kyu Chang

    2013-10-01

    A simple method is proposed for growing vertically aligned carbon nanotubes on metal foil using the triode direct current plasma-enhanced chemical vapor deposition (PECVD). The carbon nanotube (CNT) electron emitter was fabricated using fewer process steps with an acid treated metal substrate. The CNT emitter was used for X-ray generation, and the X-ray image of mouse's joint was obtained with an anode current of 0.5 mA at an anode bias of 60 kV. The simple fabrication of a well-aligned CNT with a protection layer on metal foil, and its X-ray application, were studied. PMID:24245201

  19. Evaluating cotton stripper field performance

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Cotton strippers are used primarily in the Southern High Plains due to the specific cotton varieties grown. Typically, cotton strippers cost about two-thirds the price of a cotton picker and range from one-half to one-fourth the horsepower. A cotton stripper also has a higher field and harvesting ef...

  20. SNS Injection Foil Experience

    SciTech Connect

    Cousineau, Sarah M; Galambos, John D; Kim, Sang-Ho; Ladd, Peter; Luck, Chris; Peters, Charles C; Polsky, Yarom; Shaw, Robert W; Macek, Robert James; Raparia, Deepak; Plum, Michael A

    2010-01-01

    The Spallation Neutron Source comprises a 1 GeV, 1.4 MW linear accelerator followed by an accumulator ring and a liquid mercury target. To manage the beam loss caused by the H0 excited states created during the H charge exchange injection into the accumulator ring, the stripper foil is located inside one of the chicane dipoles. This has some interesting consequences that were not fully appreciated until the beam power reached about 840 kW. One consequence was sudden failure of the stripper foil system due to convoy electrons stripped from the incoming H beam, which circled around to strike the foil bracket and cause bracket failure. Another consequence is that convoy electrons can reflect back up from the electron catcher and strike the foil and bracket. An additional contributor to foil system failure is vacuum breakdown due to the charge developed on the foil by secondary electron emission. In this paper we will detail these and other interesting failure mechanisms, and describe the improvements we have made to mitigate them.

  1. Laser Wire Stripper

    NASA Technical Reports Server (NTRS)

    1983-01-01

    NASA-developed space shuttle technology is used in a laser wire stripper designed by Raytheon Company. Laser beams cut through insulation on a wire without damaging conductive metal, because laser radiation that melts plastic insulation is reflected by the metal. The laser process is fast, clean, precise and repeatable. It eliminates quality control problems and the expense of rejected wiring.

  2. Influence of oxygen on nitrogen-doped carbon nanofiber growth directly on nichrome foil.

    PubMed

    Vishwakarma, Riteshkumar; Shinde, Sachin M; Rosmi, Mohamad Saufi; Takahashi, Chisato; Papon, Remi; Mahyavanshi, Rakesh D; Ishii, Yosuke; Kawasaki, Shinji; Kalita, Golap; Tanemura, Masaki

    2016-09-01

    The synthesis of various nitrogen-doped (N-doped) carbon nanostructures has been significantly explored as an alternative material for energy storage and metal-free catalytic applications. Here, we reveal a direct growth technique of N-doped carbon nanofibers (CNFs) on flexible nichrome (NiCr) foil using melamine as a solid precursor. Highly reactive Cr plays a critical role in the nanofiber growth process on the metal alloy foil in an atmospheric pressure chemical vapor deposition (APCVD) process. Oxidation of Cr occurs in the presence of oxygen impurities, where Ni nanoparticles are formed on the surface and assist the growth of nanofibers. Energy-dispersive x-ray spectroscopy (EDXS) and x-ray photoelectron spectroscopy (XPS) clearly show the transformation process of the NiCr foil surface with annealing in the presence of oxygen impurities. The structural change of NiCr foil assists one-dimensional (1D) CNF growth, rather than the lateral two-dimensional (2D) growth. The incorporation of distinctive graphitic and pyridinic nitrogen in the graphene lattice are observed in the synthesized nanofiber, owing to better nitrogen solubility. Our finding shows an effective approach for the synthesis of highly N-doped carbon nanostructures directly on Cr-based metal alloys for various applications. PMID:27479000

  3. Influence of oxygen on nitrogen-doped carbon nanofiber growth directly on nichrome foil

    NASA Astrophysics Data System (ADS)

    Vishwakarma, Riteshkumar; Shinde, Sachin M.; Saufi Rosmi, Mohamad; Takahashi, Chisato; Papon, Remi; Mahyavanshi, Rakesh D.; Ishii, Yosuke; Kawasaki, Shinji; Kalita, Golap; Tanemura, Masaki

    2016-09-01

    The synthesis of various nitrogen-doped (N-doped) carbon nanostructures has been significantly explored as an alternative material for energy storage and metal-free catalytic applications. Here, we reveal a direct growth technique of N-doped carbon nanofibers (CNFs) on flexible nichrome (NiCr) foil using melamine as a solid precursor. Highly reactive Cr plays a critical role in the nanofiber growth process on the metal alloy foil in an atmospheric pressure chemical vapor deposition (APCVD) process. Oxidation of Cr occurs in the presence of oxygen impurities, where Ni nanoparticles are formed on the surface and assist the growth of nanofibers. Energy-dispersive x-ray spectroscopy (EDXS) and x-ray photoelectron spectroscopy (XPS) clearly show the transformation process of the NiCr foil surface with annealing in the presence of oxygen impurities. The structural change of NiCr foil assists one-dimensional (1D) CNF growth, rather than the lateral two-dimensional (2D) growth. The incorporation of distinctive graphitic and pyridinic nitrogen in the graphene lattice are observed in the synthesized nanofiber, owing to better nitrogen solubility. Our finding shows an effective approach for the synthesis of highly N-doped carbon nanostructures directly on Cr-based metal alloys for various applications.

  4. Charge-state resolved energy spectra of swift 22Ne ions passing through thin carbon foils

    NASA Astrophysics Data System (ADS)

    Blazevic, A.; Bohlen, H. G.; von Oertzen, W.; Balashov, V. V.; Stysin, A. V.

    2006-04-01

    The method of coupled kinetic equations for a unified description of charge exchange and excitation of ions passing through matter is applied to calculate energy-loss spectra of swift 22Ne ions in carbon foils in the non-equilibrium regime. Good agreement is obtained for these calculations with the results of recent measurements, performed at the ISL-facility at the Hahn-Meitner Institute.

  5. The survivability of phyllosilicates and carbonates impacting Stardust Al foils: Facilitating the search for cometary water

    NASA Astrophysics Data System (ADS)

    Wozniakiewicz, Penelope J.; Ishii, Hope A.; Kearsley, Anton T.; Bradley, John P.; Price, Mark. C.; Burchell, Mark J.; Teslich, Nick; Cole, Mike J.

    2015-11-01

    Comet 81P/Wild 2 samples returned by NASA's Stardust mission provide an unequalled opportunity to study the contents of, and hence conditions and processes operating on, comets. They can potentially validate contentious interpretations of cometary infrared spectra and in situ mass spectrometry data: specifically the identification of phyllosilicates and carbonates. However, Wild 2 dust was collected via impact into capture media at ~6 km s-1, leading to uncertainty as to whether these minerals were captured intact, and, if subjected to alteration, whether they remain recognizable. We simulated Stardust Al foil capture conditions using a two-stage light-gas gun, and directly compared transmission electron microscope analyses of pre- and postimpact samples to investigate survivability of lizardite and cronstedtite (phyllosilicates) and calcite (carbonate). We find the phyllosilicates do not survive impact as intact crystalline materials but as moderately to highly vesiculated amorphous residues lining resultant impact craters, whose bulk cation to Si ratios remain close to that of the impacting grain. Closer inspection reveals variation in these elements on a submicron scale, where impact-induced melting accompanied by reducing conditions (due to the production of oxygen scavenging molten Al from the target foils) has resulted in the production of native silicon and Fe- and Fe-Si-rich phases. In contrast, large areas of crystalline calcite are preserved within the calcite residue, with smaller regions of vesiculated, Al-bearing calcic glass. Unambiguous identification of calcite impactors on Stardust Al foil is therefore possible, while phyllosilicate impactors may be inferred from vesiculated residues with appropriate bulk cation to Si ratios. Finally, we demonstrate that the characteristic textures and elemental distributions identifying phyllosilicates and carbonates by transmission electron microscopy can also be observed by state-of-the-art scanning electron

  6. X-ray Thomson scattering diagnostics of impact ionization in laser-driven carbon foils

    NASA Astrophysics Data System (ADS)

    Sperling, P.; Zastrau, U.; Toleikis, S.; Glenzer, S. H.; Redmer, R.

    2015-06-01

    We have studied the light-matter interaction of ultra-short, intense optical laser fields with thin carbon foils via particle-in-cell simulations. Especially, the influence of additional impact ionization on the density and temperature of the generated plasma and on the corresponding Thomson scattering spectra was investigated. We predict a pump-probe experiment at the free electron laser FLASH in order to verify the importance of this effect in the laser-matter interaction on ultra-short time scales and to check our predictions quantitatively.

  7. Dynamics of formation of K-hole fractions of sulfur projectiles inside a carbon foil

    SciTech Connect

    Braziewicz, J.; Majewska, U.; Slabkowska, K.; Polasik, M.; Fijal, I.; Jaskola, M.; Korman, A.; Czarnacki, W.; Chojnacki, S.; Kretschmer, W.

    2004-06-01

    The K{alpha} and K{beta} satellite and hypersatellite x-ray lines emitted by highly ionized sulfur projectiles passing with energies from 65 MeV up to 122 MeV through carbon foils of thickness of 15-210 {mu}g cm{sup -2} have been recorded using a Si(Li) detector. The additional hypersatellite Ky{sup h} peak proves that for such high energies of the sulfur ions very high subshells (4p and 5p) could be occupied. In order to study the dynamics of formation of K-shell vacancy fractions of sulfur projectiles passing through a carbon foil the dependence of sulfur K x-ray production cross sections on foil thickness has been examined separately for each recorded line using the three component model. For each projectile energy the values of K-shell hole production cross sections and K-shell electron capture cross sections (both common for all recorded x-ray lines in the case of each projectile energy) have been fitted, as well as the specific values (for each recorded x-ray line) of K-shell hole filling cross sections, which are directly connected with average lifetimes of appropriate states of sulfur ions. The obtained ''experimental'' values of K-shell vacancy production cross sections are much higher than the theoretical predictions. This suggests that apart from the ionization process the excitation from K shell into higher shells is responsible for a production of K-shell vacancies, which has been confirmed by recent classical trajectory Monte Carlo calculations.

  8. From graphene to carbon nanotube: The oxygen effect on the synthesis of carbon nanomaterials on nickel foil during CVD process

    NASA Astrophysics Data System (ADS)

    Chou, Yu-Ching; Wu, Hsuan-Chung; Hsieh, Chien-Kuo

    2016-01-01

    In this study, we demonstrated an oxygen-assisted ultralow-pressure (20 mTorr) chemical vapor deposition (CVD) method for the synthesis of carbon nanomaterials, including multilayer graphene (MLG), double-layer graphene (DLG), single-layer graphene (SLG), and carbon nanotubes (CNTs) on a Ni foil substrate. Oxygen is typically considered undesirable to synthesize carbon nanomaterials during the CVD process. However, our study provided evidence demonstrating that the growth of MLG, DLG, SLG, and CNTs can be maintained by adjusting the oxygen concentration during the CVD process; it also provided an easy way in controlling the layer of graphene. It was observed that oxygen played an important role in controlling the synthesis of carbon nanomaterials.

  9. Denser and taller carbon nanotube arrays on Cu foils useable as thermal interface materials

    NASA Astrophysics Data System (ADS)

    Na, Nuri; Hasegawa, Kei; Zhou, Xiaosong; Nihei, Mizuhisa; Noda, Suguru

    2015-09-01

    To achieve denser and taller carbon nanotube (CNT) arrays on Cu foils, catalyst and chemical vapor deposition (CVD) conditions were carefully engineered. CNTs were grown to ˜50 µm using Fe/TiN/Ta catalysts in which Ta and TiN acted as diffusion barriers for Cu and Ta, respectively. A tradeoff was found between the mass density and height of the CNT arrays, and CNT arrays with a mass density of 0.30 g cm-3 and height of 45 µm were achieved under optimized conditions. Thermal interface materials (TIMs) with CNT array/Cu foil/CNT array structures showed decreasing thermal resistance from 86 to 24 mm2 K W-1 with increasing CNT array mass densities from 0.07-0.08 to 0.19-0.26 g cm-3 for Cu and Al blocks with surfaces as rough as 20-30 µm. The best CNT/Cu/CNT TIMs showed thermal resistance values comparable to that of a typical indium sheet TIM.

  10. Application of aluminum foil for ``strain sensing'' at fatigue damage evaluation of carbon fiber composite

    NASA Astrophysics Data System (ADS)

    Panin, Sergey; Burkov, Mikhail; Lyubutin, Pavel; Altukhov, Yurii

    2014-01-01

    Surface layer of a loaded solid is an individual structural level of deformation that was shown numerously within concept of physical mesomechanics. This gives rise to advance in its deformation development under loading as well as allows using this phenomenon to sense the strain induced structure changes. It is of specific importance for composite materials since they are highly heterogeneous while estimating their mechanical state is a topical applied problem. Fatigue tests of carbon fiber composite specimens were carried out for cyclic deformation estimation with the use of strain sensors made of thin (80 μm) aluminum foil glued to the specimen's surface. The surface images were captured by DSLR camera mounted onto an optical microscope. Strain relief to form during cyclic loading was numerically estimated using different parameters: dispersion, mean square error, universal image quality index, fractal dimension and energy of Fourier spectrum. The results are discussed in view of deformation mismatch in thin foil and bulk specimen and are offered to be applied for the development of Structural Health Monitoring (SHM) approach.

  11. RTF glovebox stripper regeneration development

    SciTech Connect

    Birchenall, A.K.

    1992-10-31

    Currently, the Replacement Tritium Facility (RTF) glovebox stripper system consists of a catalytic oxidation front end where trace tritium which may escape from the primary tritium process into the glovebox nitrogen system is oxidized to tritiated water. The tritiated water, along with normal water which may leak into the glovebox from the surrounding atmosphere, is then captured on a zeolite bed. Eventually, the zeolite bed becomes saturated with water and must be regenerated to remain effective as a stripper. This is accomplished by heating the zeolite and evolving the trapped water which is then passed over an elevated temperature uranium bed. A waste minimization program was instituted to address this issue. The program has two parallel paths. One path investigates replacing the entire glovebox stripper system with a system of getters to scavenge trace tritium. This report concentrates on the second path, retaining the catalytic oxidation front end but replacing the uranium bed water cracking with alternative technologies.

  12. Charge state evolution of 2 MeV/u sulfur ion passing through thin carbon foil

    NASA Astrophysics Data System (ADS)

    Imai, M.; Sataka, M.; Kawatsura, K.; Takahiro, K.; Komaki, K.; Shibata, H.; Sugai, H.; Nishio, K.

    2007-03-01

    Charge state distribution and its evolution for 2.0 MeV/u sulfur ions after passing through 0.9, 1.1, 1.5, 2.0, 3.0, 4.7, 6.9 and 10 μg/cm2 carbon foils have been extensively studied following our previous paper [M. Imai, M. Sataka, K. Kawatsura, K. Takahiro, K. Komaki, H. Shibata, H. Sugai, K. Nishio, Nucl. Instr. and Meth. B 230 (2005) 63] to derive data for all the initial charge states between 6+ and 14+. Measured charge state distributions, their mean charge states and distribution widths do not flat off to establish equilibrium within the measured target thickness, and an overshooting feature of the distribution width for S6+ projectile is observed around 1 μg/cm2 in the target thickness. Two kinds of calculations, one based on rate equations accounting only for single charge transfer and the other applying ETACHA code, show good agreements with the experimental evolutions of mean charge and distribution width.

  13. Foil Artists

    ERIC Educational Resources Information Center

    Szekely, George

    2010-01-01

    Foil can be shaped into almost anything--it is the all-purpose material for children's art. Foil is a unique drawing surface. It reflects, distorts and plays with light and imagery as young artists draw over it. Foil permits quick impressions of a model or object to be sketched. Foil allows artists to track their drawing moves, seeing the action…

  14. High power cladding light strippers

    NASA Astrophysics Data System (ADS)

    Wetter, Alexandre; Faucher, Mathieu; Sévigny, Benoit

    2008-02-01

    The ability to strip cladding light from double clad fiber (DCF) fibers is required for many different reasons, one example is to strip unwanted cladding light in fiber lasers and amplifiers. When removing residual pump light for example, this light is characterized by a large numerical aperture distribution and can reach power levels into the hundreds of watts. By locally changing the numerical aperture (N.A.) of the light to be stripped, it is possible to achieve significant attenuation even for the low N.A. rays such as escaped core modes in the same device. In order to test the power-handling capability of this device, one hundred watts of pump and signal light is launched from a tapered fusedbundle (TFB) 6+1x1 combiner into a high power-cladding stripper. In this case, the fiber used in the cladding stripper and the output fiber of the TFB was a 20/400 0.06/0.46 N.A. double clad fiber. Attenuation of over 20dB in the cladding was measured without signal loss. By spreading out the heat load generated by the unwanted light that is stripped, the package remained safely below the maximum operating temperature internally and externally. This is achieved by uniformly stripping the energy along the length of the fiber within the stripper. Different adhesive and heat sinking techniques are used to achieve this uniform removal of the light. This suggests that these cladding strippers can be used to strip hundreds of watts of light in high power fiber lasers and amplifiers.

  15. ADVANCED STRIPPER GAS PRODUCED WATER REMEDIATION

    SciTech Connect

    Ray W. Sheldon, P.E.

    2001-11-01

    Natural gas and oil production from stripper wells also produces water contaminated with hydrocarbons, and in most locations, salts and trace elements. The hydrocarbons are not generally present in concentrations that allow the operator to economically recover these liquids. Produced liquids, (Stripper Gas Water) which are predominantly water, present the operator with two options; purify the water to acceptable levels of contaminates, or pay for the disposal of the water. The project scope involves testing SynCoal as a sorbent to reduce the levels of contamination in stripper gas well produced water to a level that the water can be put to a productive use. Produced water is to be filtered with SynCoal, a processed sub-bituminous coal. It is expected that the surface area of and in the SynCoal would sorb the hydrocarbons and other contaminates and the effluent would be usable for agricultural purposes. Test plan anticipates using two well locations described as being disparate in the level and type of contaminates present. The loading capacity and the rate of loading for the sorbent should be quantified in field testing situations which include unregulated and widely varying liquid flow rates. This will require significant flexibility in the initial stages of the investigation. The scope of work outlined below serves as the guidelines for the testing of SynCoal carbon product as a sorbent to remove hydrocarbons and other contaminants from the produced waters of natural gas wells. A maximum ratio of 1 lb carbon to 100 lbs water treated is the initial basis for economic design. While the levels of contaminants directly impact this ratio, the ultimate economics will be dictated by the filter servicing requirements. This experimental program is intended to identify those treatment parameters that yield the best technological practice for a given set of operating conditions. The goal of this research is to determine appropriate guidelines for field trials by accurately

  16. ADVANCED STRIPPER GAS PRODUCED WATER REMEDIATION

    SciTech Connect

    Harry Bonner; Roger Malmquist

    2002-10-01

    Natural gas and oil production from stripper wells also produces water contaminated with hydrocarbons, and in most locations, salts and trace elements. The hydrocarbons are not generally present in concentrations that allow the operator to economically recover these liquids. Produced liquids, (Stripper Gas Water) which are predominantly water, present the operator with two options; purify the water to acceptable levels of contaminates, or pay for the disposal of the water. The project scope involves testing SynCoal as a sorbent to reduce the levels of contamination in stripper gas well produced water to a level that the water can be put to a productive use. Produced water is to be filtered with SynCoal, a processed sub-bituminous coal. It is expected that the surface area of and in the SynCoal would sorb the hydrocarbons and other contaminates and the effluent would be usable for agricultural purposes. Test plan anticipates using two well locations described as being disparate in the level and type of contaminates present. The loading capacity and the rate of loading for the sorbent should be quantified in field testing situations which include unregulated and widely varying liquid flow rates. This will require significant flexibility in the initial stages of the investigation. The scope of work outlined below serves as the guidelines for the testing of SynCoal carbon product as a sorbent to remove hydrocarbons and other contaminants from the produced waters of natural gas wells. A maximum ratio of 1 lb carbon to 100 lbs water treated is the initial basis for economic design. While the levels of contaminants directly impact this ratio, the ultimate economics will be dictated by the filter servicing requirements. This experimental program is intended to identify those treatment parameters that yield the best technological practice for a given set of operating conditions. The goal of this research is to determine appropriate guidelines for field trials by accurately

  17. ADVANCED STRIPPER GAS PRODUCED WATER REMEDIATION

    SciTech Connect

    Ray W. Sheldon

    2001-09-01

    Natural gas and oil production from stripper wells also produces water contaminated with hydrocarbons, and in most locations, salts and trace elements. The hydrocarbons are not generally present in concentrations that allow the operator to economically recover these liquids. Produced liquids, (stripper gas water) which are predominantly water, present the operator with two options; purify the water to acceptable levels of contaminates, or pay for the disposal of the water. The project scope involves testing SynCoal as a sorbent to reduce the levels of contamination in stripper gas well produced water to a level that the water can be put to a productive use. Produced water is to be filtered with SynCoal, a processed sub-bituminous coal. It is expected that the surface area of and in the SynCoal would sorb the hydrocarbons and other contaminates and the effluent would be usable for agricultural purposes. Test plan anticipates using two well locations described as being disparate in the level and type of contaminates present. The loading capacity and the rate of loading for the sorbent should be quantified in field testing situations which include unregulated and widely varying liquid flow rates. This will require significant flexibility in the initial stages of the investigation. The scope of work outlined below serves as the guidelines for the testing of SynCoal carbon product as a sorbent to remove hydrocarbons and other contaminants from the produced waters of natural gas wells. A maximum ratio of 1 lb carbon to 100 lbs water treated is the initial basis for economic design. While the levels of contaminants directly impact this ratio, the ultimate economics will be dictated by the filter servicing requirements. This experimental program is intended to identify those treatment parameters that yield the best technological practice for a given set of operating conditions. The goal of this research is to determine appropriate guidelines for field trials by accurately

  18. ADVANCED STRIPPER GAS PRODUCED WATER REMEDIATION

    SciTech Connect

    Harry Bonner; Roger Malmquist

    2002-04-01

    Natural gas and oil production from stripper wells also produces water contaminated with hydrocarbons, and in most locations, salts and trace elements. The hydrocarbons are not generally present in concentrations that allow the operator to economically recover these liquids. Produced liquids, (Stripper Gas Water) which are predominantly water, present the operator with two options; purify the water to acceptable levels of contaminates, or pay for the disposal of the water. The project scope involves testing SynCoal as a sorbent to reduce the levels of contamination in stripper gas well produced water to a level that the water can be put to a productive use. Produced water is to be filtered with SynCoal, a processed sub-bituminous coal. It is expected that the surface area of and in the SynCoal would sorb the hydrocarbons and other contaminates and the effluent would be usable for agricultural purposes. Test plan anticipates using two well locations described as being disparate in the level and type of contaminates present. The loading capacity and the rate of loading for the sorbent should be quantified in field testing situations which include unregulated and widely varying liquid flow rates. This will require significant flexibility in the initial stages of the investigation. The scope of work outlined below serves as the guidelines for the testing of SynCoal carbon product as a sorbent to remove hydrocarbons and other contaminants from the produced waters of natural gas wells. A maximum ratio of 1 lb carbon to 100 lbs water treated is the initial basis for economic design. While the levels of contaminants directly impact this ratio, the ultimate economics will be dictated by the filter servicing requirements. This experimental program is intended to identify those treatment parameters that yield the best technological practice for a given set of operating conditions. The goal of this research is to determine appropriate guidelines for field trials by accurately

  19. ADVANCED STRIPPER GAS PRODUCED WATER REMEDIATION

    SciTech Connect

    Harry Bonner; Roger Malmquist

    2002-01-01

    Natural gas and oil production from stripper wells also produces water contaminated with hydrocarbons, and in most locations, salts and trace elements. The hydrocarbons are not generally present in concentrations that allow the operator to economically recover these liquids. Produced liquids, (Stripper Gas Water) which are predominantly water, present the operator with two options; purify the water to acceptable levels of contaminates, or pay for the disposal of the water. The project scope involves testing SynCoal as a sorbent to reduce the levels of contamination in stripper gas well produced water to a level that the water can be put to a productive use. Produced water is to be filtered with SynCoal, a processed sub-bituminous coal. It is expected that the surface area of and in the SynCoal would sorb the hydrocarbons and other contaminates and the effluent would be usable for agricultural purposes. Test plan anticipates using two well locations described as being disparate in the level and type of contaminates present. The loading capacity and the rate of loading for the sorbent should be quantified in field testing situations which include unregulated and widely varying liquid flow rates. This will require significant flexibility in the initial stages of the investigation. The scope of work outlined below serves as the guidelines for the testing of SynCoal carbon product as a sorbent to remove hydrocarbons and other contaminants from the produced waters of natural gas wells. A maximum ratio of 1 lb carbon to 100 lbs water treated is the initial basis for economic design. While the levels of contaminants directly impact this ratio, the ultimate economics will be dictated by the filter servicing requirements. This experimental program is intended to identify those treatment parameters that yield the best technological practice for a given set of operating conditions. The goal of this research is to determine appropriate guidelines for field trials by accurately

  20. ADVANCED STRIPPER GAS PRODUCED WATER REMEDIATION

    SciTech Connect

    Harry Bonner; Roger Malmquist

    2002-07-01

    Natural gas and oil production from stripper wells also produces water contaminated with hydrocarbons, and in most locations, salts and trace elements. The hydrocarbons are not generally present in concentrations that allow the operator to economically recover these liquids. Produced liquids, (Stripper Gas Water) which are predominantly water, present the operator with two options; purify the water to acceptable levels of contaminates, or pay for the disposal of the water. The project scope involves testing SynCoal as a sorbent to reduce the levels of contamination in stripper gas well produced water to a level that the water can be put to a productive use. Produced water is to be filtered with SynCoal, a processed sub-bituminous coal. It is expected that the surface area of and in the SynCoal would sorb the hydrocarbons and other contaminates and the effluent would be usable for agricultural purposes. Test plan anticipates using two well locations described as being disparate in the level and type of contaminates present. The loading capacity and the rate of loading for the sorbent should be quantified in field testing situations which include unregulated and widely varying liquid flow rates. This will require significant flexibility in the initial stages of the investigation. The scope of work outlined below serves as the guidelines for the testing of SynCoal carbon product as a sorbent to remove hydrocarbons and other contaminants from the produced waters of natural gas wells. A maximum ratio of 1 lb carbon to 100 lbs water treated is the initial basis for economic design. While the levels of contaminants directly impact this ratio, the ultimate economics will be dictated by the filter servicing requirements. This experimental program is intended to identify those treatment parameters that yield the best technological practice for a given set of operating conditions. The goal of this research is to determine appropriate guidelines for field trials by accurately

  1. ADVANCED STRIPPER GAS PRODUCED WATER REMEDIATION

    SciTech Connect

    Harry Bonner; Roger Malmquist

    2003-11-01

    Natural gas and oil production from stripper wells also produces water contaminated with hydrocarbons, and in most locations, salts and trace elements. The hydrocarbons are not generally present in concentrations that allow the operator to economically recover these liquids. Produced liquids, (Stripper Gas Water) which are predominantly water, present the operator with two options; purify the water to acceptable levels of contaminates, or pay for the disposal of the water. The project scope involves testing SynCoal as a sorbent to reduce the levels of contamination in stripper gas well produced water to a level that the water can be put to a productive use. Produced water is to be filtered with SynCoal, a processed sub-bituminous coal. It is expected that the surface area of and in the SynCoal would sorb the hydrocarbons and other contaminates and the effluent would be usable for agricultural purposes. Test plan anticipates using two well locations described as being disparate in the level and type of contaminates present. The loading capacity and the rate of loading for the sorbent should be quantified in field testing situations which include unregulated and widely varying liquid flow rates. This will require significant flexibility in the initial stages of the investigation. The scope of work outlined below serves as the guidelines for the testing of SynCoal carbon product as a sorbent to remove hydrocarbons and other contaminants from the produced waters of natural gas wells. A maximum ratio of 1 lb carbon to 100 lbs water treated is the initial basis for economic design. While the levels of contaminants directly impact this ratio, the ultimate economics will be dictated by the filter servicing requirements. This experimental program was intended to identify those treatment parameters that yield the best technological practice for a given set of operating conditions. The goal of this research was to determine appropriate guidelines for field trials by

  2. ADVANCED STRIPPER GAS PRODUCED WATER REMEDIATION

    SciTech Connect

    Harry Bonner; Roger Malmquist

    2003-01-01

    Natural gas and oil production from stripper wells also produces water contaminated with hydrocarbons, and in most locations, salts and trace elements. The hydrocarbons are not generally present in concentrations that allow the operator to economically recover these liquids. Produced liquids, (Stripper Gas Water) which are predominately water, present the operator with two options; purify the water to acceptable levels of contaminates, or pay for the disposal of the water. The project scope involves testing SynCoal as a sorbent to reduce the levels of contamination in stripper gas well produced water to a level that the water can be put to a productive use. Produced water is to be filtered with SynCoal, a processed sub-bituminous coal. It is expected that the surface area of and in the SynCoal would sorb the hydrocarbons and other contaminates and the effluent would be usable for agricultural purposes. Test plan anticipates using two well locations described as being disparate in the level and type of contaminates present. The loading capacity and the rate of loading for the sorbent should be quantified in field testing situations which include unregulated and widely varying liquid flow rates. This will require significant flexibility in the initial stages of the investigation. The scope of work outlined below serves as the guidelines for the testing of SynCoal carbon product as a sorbent to remove hydrocarbons and other contaminants from the produced waters of natural gas wells. A maximum ratio of 1 lb carbon to 100 lbs water treated is the initial basis for economic design. While the levels of contaminants directly impact this ratio, the ultimate economics will be dictated by the filter servicing requirements. This experimental program is intended to identify those treatment parameters that yield the best technological practice for a given set of operating conditions. The goal of this research is to determine appropriate guidelines for field trials by accurately

  3. ADVANCED STRIPPER GAS PRODUCED WATER REMEDIATION

    SciTech Connect

    Harry Bonner; Roger Malmquist

    2003-08-01

    Natural gas and oil production from stripper wells also produces water contaminated with hydrocarbons, and in most locations, salts and trace elements. The hydrocarbons are not generally present in concentrations that allow the operator to economically recover these liquids. Produced liquids, (Stripper Gas Water) which are predominantly water, present the operator with two options; purify the water to acceptable levels of contaminates, or pay for the disposal of the water. The project scope involves testing SynCoal as a sorbent to reduce the levels of contamination in stripper gas well produced water to a level that the water can be put to a productive use. Produced water is to be filtered with SynCoal, a processed sub-bituminous coal. It is expected that the surface area of and in the SynCoal would sorb the hydrocarbons and other contaminates and the effluent would be usable for agricultural purposes. Test plan anticipates using two well locations described as being disparate in the level and type of contaminates present. The loading capacity and the rate of loading for the sorbent should be quantified in field testing situations which include unregulated and widely varying liquid flow rates. This will require significant flexibility in the initial stages of the investigation. The scope of work outlined below serves as the guidelines for the testing of SynCoal carbon product as a sorbent to remove hydrocarbons and other contaminants from the produced waters of natural gas wells. A maximum ratio of 1 lb carbon to 100 lbs water treated is the initial basis for economic design. While the levels of contaminants directly impact this ratio, the ultimate economics will be dictated by the filter servicing requirements. This experimental program is intended to identify those treatment parameters that yield the best technological practice for a given set of operating conditions. The goal of this research is to determine appropriate guidelines for field trials by accurately

  4. Angular scattering of 1–50 keV ions through graphene and thin carbon foils: Potential applications for space plasma instrumentation

    SciTech Connect

    Ebert, Robert W.; Allegrini, Frédéric; Fuselier, Stephen A.; Nicolaou, Georgios; Physics and Astronomy Department, University of Texas at San Antonio, One UTSA Circle, San Antonio, Texas 78249 ; Bedworth, Peter; Sinton, Steve; Trattner, Karlheinz J.; Laboratory for Atmospheric and Space Physics, University of Colorado, 1234 Innovation Drive, Boulder, Colorado 80303

    2014-03-15

    We present experimental results for the angular scattering of ∼1–50 keV H, He, C, O, N, Ne, and Ar ions transiting through graphene foils and compare them with scattering through nominal ∼0.5 μg cm{sup −2} carbon foils. Thin carbon foils play a critical role in time-of-flight ion mass spectrometers and energetic neutral atom sensors in space. These instruments take advantage of the charge exchange and secondary electron emission produced as ions or neutral atoms transit these foils. This interaction also produces angular scattering and energy straggling for the incident ion or neutral atom that acts to decrease the performance of a given instrument. Our results show that the angular scattering of ions through graphene is less pronounced than through the state-of-the-art 0.5 μg cm{sup −2} carbon foils used in space-based particle detectors. At energies less than 50 keV, the scattering angle half width at half maximum, ψ{sub 1/2}, for ∼3–5 atoms thick graphene is up to a factor of 3.5 smaller than for 0.5 μg cm{sup −2} (∼20 atoms thick) carbon foils. Thus, graphene foils have the potential to improve the performance of space-based plasma instruments for energies below ∼50 keV.

  5. Electrochemical Stability of Carbon Fibers Compared to Metal Foils as Current Collectors for Lithium-Ion Batteries

    SciTech Connect

    Martha, Surendra K; Dudney, Nancy J; Kiggans, Jim; Nanda, Jagjit

    2012-01-01

    The electrochemical behaviors of highly conductive, fully-graphitic, semi-graphitic and non-graphitic carbon fibers were studied as the cathode current collectors of lithium batteries in standard electrolyte (alkyl carbonate/LiPF6) solutions and compared to bare aluminum (Al). All of these current collectors demonstrate a stable electrochemical behavior within the potential range of 2.5 to 5 V, due to passivation by surface films. Carbon fibers have comparable electrochemical stability of Al and may be used in place Al foil. While the carbon fibers do not contribute any irreversible or extra capacity when they are cycled below 4.5 V, for fully-graphitic and semi-graphitic fibers PF6 intercalation and deintercalation into the carbon fiber may occur when they are cycled at high potentials >4.5 V.

  6. Modified titanium foil's surface by high temperature carbon sintering method as the substrate for bipolar lead-acid battery

    NASA Astrophysics Data System (ADS)

    Lang, Xiaoshi; Wang, Dianlong; Zhu, Junsheng

    2014-12-01

    Titanium foil can be a type of ideal material as the substrate for bipolar lead-acid battery. However, it can't be directly used because it can be oxidized in the high voltage and strong oxidizing conditions. In this paper, we coat the titanium suboxide on the titanium foil surface by means of the high temperature carbon sintering method for the improvement of corrosion resistance of titanium metal and use it as the substrate to bipolar lead-acid battery to study its effect on the battery performances. Modified titanium foils are characterized by SEM, XRD, corrosion resistance test and electronic conductivity test. The electrochemical properties of the bipolar lead-acid battery are investigated by constant current charge/discharge method. The results demonstrate that the titanium foil carbon-sintered at 800 °C for 2 h has the most excellent chemical stability and electronic conductivity. Initial specific capacities of positive active material of bipolar lead-acid battery with modified titanium as the substrate at 0.25C, 0.5C, 1C and 2C discharge rate are 99.29 mAh g-1, 88.93 mAh g-1, 77.54 mAh g-1, and 65.41 mAh g-1. After 50 cycles, the specific capacity of positive active material at 0.5C is 81.36 mAh g-1 and after 100 cycles, the specific capacity at 1C is 61.92 mAh g-1.

  7. Radiative double electron capture in collisions of fully-stripped fluorine ions with thin carbon foils

    NASA Astrophysics Data System (ADS)

    Elkafrawy, Tamer Mohammad Samy

    Radiative double electron capture (RDEC) is a one-step process in ion-atom collisions occurring when two target electrons are captured to a bound state of the projectile simultaneously with the emission of a single photon. The emitted photon has approximately double the energy of the photon emitted due to radiative electron capture (REC), which occurs when a target electron is captured to a projectile bound state with simultaneous emission of a photon. REC and RDEC can be treated as time-reversed photoionization (PI) and double photoionization (DPI), respectively, if loosely-bound target electrons are captured. This concept can be formulated with the principle of detailed balance, in which the processes of our interest can be described in terms of their time-reversed ones. Fully-stripped ions were used as projectiles in the performed RDEC experiments, providing a recipient system free of electron-related Coulomb fields. This allows the target electrons to be transferred without interaction with any of the projectile electrons, enabling accurate investigation of the electron-electron interaction in the vicinity of electromagnetic field. In this dissertation, RDEC was investigated during the collision of fully-stripped fluorine ions with a thin carbon foil and the results are compared with the recent experimental and theoretical studies. In the current work, x rays associated with projectile charge-changing by single and double electron capture and no charge change by F9+ ions were observed and compared with recent work for O8+ ions and with theory. Both the F 9+ and O8+ ions had energies in the ˜MeV/u range. REC, in turn, was investigated as a means to compare with the theoretical predictions of the RDEC/REC cross section ratio. The most significant background processes including various mechanisms of x-ray emission that may interfere with the energy region of interest are addressed in detail. This enables isolation of the contributions of REC and RDEC from the

  8. Liquid-film electron stripper

    DOEpatents

    Gavin, Basil F.

    1986-01-01

    An improved liquid-film electron stripper particularly for high intensity heavy ion beams which produces constant regenerated, stable, free-standing liquid films having an adjustable thickness between 0.3 to 0.05 microns. The improved electron stripper is basically composed of at least one high speed, rotating disc with a very sharp, precision-like, ground edge on one said of the disc's periphery and with a highly polished, flat, radial surface adjacent the sharp edge. A fine stream of liquid, such as oil, impinges at a 90.degree. angle adjacent the disc's sharp outer edge. Film terminators, located at a selected distance from the disc perimeter are positioned approximately perpendicular to the film. The terminators support, shape, and stretch the film and are arranged to assist in the prevention of liquid droplet formation by directing the collected film to a reservoir below without breaking or interfering with the film. One embodiment utilizes two rotating discs and associated terminators, with the discs rotating so as to form films in opposite directions, and with the second disc being located down beam-line relative to the first disc.

  9. Combined air stripper/membrane vapor separation systems. Final report

    SciTech Connect

    Wijmans, J.G.; Baker, R.W.; Kamaruddin, H.D.; Kaschemekat, J.; Olsen, R.P.; Rose, M.E.; Segelke, S.V.

    1992-11-01

    Air stripping is an economical and efficient method of removing dissolved volatile organic compounds (VOCs) from contaminated groundwater. Air strippers, however, produce a vent air stream, which must meet the local air quality limits. If the VOC content exceeds the limits, direct discharge is not possible; therefore, a carbon adsorption VOC capture system is used to treat the vent air. This treatment step adds a cost of at least $50/lb of VOC captured. In this program, a combined air stripper/membrane vapor separation system was constructed and demonstrated in the laboratory. The membrane system captures VOCs from the stripper vent stream at a projected cost of $15/lb VOC for a water VOC content of 5 ppmw, and $75/lb VOC for a water VOC content of 1 ppmw. The VOCs are recovered as a small, concentrated liquid fraction for disposal or solvent recycling. The concept has been demonstrated in experiments with a system capable of handling up to 150,000 gpd of water. The existing demonstration system is available for field tests at a DOE facility or remediation site. Replacement of the current short air stripping tower (effective height 3 m) with a taller tower is recommended to improve VOC removal.

  10. Investigation of the influence of surface composition on the charge state distribution of ∼keV hydrogen exiting thin carbon foils for space plasma instrumentation

    NASA Astrophysics Data System (ADS)

    Allegrini, Frédéric; Coulter, Kent; Ebert, Robert W.; Nicolaou, Georgios; Poenitzsch, Vasiliki Zorbas

    2016-06-01

    Energetic neutral atom (ENA) imaging techniques have become a powerful tool for remotely probing plasma environments in space. ENA imagers cover energies from 0.01 keV up to a few MeV, and they use different techniques to cover such a broad energy range. Most of them convert the ENA into a charged particle to remove the converted ENA from the initial neutral direction. In the >∼0.2 keV/nuc to 10's of keV/nuc range, the conversion subsystem is usually an ultra-thin carbon foil. The sensitivity of ENA imagers based on charge conversion by carbon foils is driven by the ability of these foils to convert a neutral atom into an ion. The charge state distribution after the carbon foils is a strong function of the chemical and physical properties of the exit surface. In this study, we analyze the composition and structure of the surface using X-ray photoelectron spectroscopy. The surface is roughly 88% carbon and 12% oxygen, forming strong Csbnd O bonds. Annealing the foil lowers the oxygen content to about 9%. We coat the surface of the foils with Au, Al2O3, or MgO. We compare the exit charge state distributions of hydrogen prior to and post coatings. While no significant difference is observed in the exit charge state for the Au and Al2O3 coatings, there is a slight decrease of the positive fraction after MgO. The annealing of the foil has the benefit of reducing the angular scattering of hydrogen by a factor of ∼1.2. This is a significant improvement that has the potential to increase sensitivity of ENA imagers.

  11. Classroom Foils

    ERIC Educational Resources Information Center

    Pafford, William N.

    1970-01-01

    Aluminum foil, because of its characteristics, can be used for many elementary science activities: demonstrating Archimedes Principle, how to reduce cohesion, reflection and mirror effect, fuse action, condensation, friction, and as containers and barriers. (BR)

  12. 21 CFR 870.4875 - Intraluminal artery stripper.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Intraluminal artery stripper. 870.4875 Section 870...) MEDICAL DEVICES CARDIOVASCULAR DEVICES Cardiovascular Surgical Devices § 870.4875 Intraluminal artery stripper. (a) Identification. An intraluminal artery stripper is a device used to perform an...

  13. 21 CFR 870.4875 - Intraluminal artery stripper.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Intraluminal artery stripper. 870.4875 Section 870...) MEDICAL DEVICES CARDIOVASCULAR DEVICES Cardiovascular Surgical Devices § 870.4875 Intraluminal artery stripper. (a) Identification. An intraluminal artery stripper is a device used to perform an...

  14. 21 CFR 870.4875 - Intraluminal artery stripper.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Intraluminal artery stripper. 870.4875 Section 870...) MEDICAL DEVICES CARDIOVASCULAR DEVICES Cardiovascular Surgical Devices § 870.4875 Intraluminal artery stripper. (a) Identification. An intraluminal artery stripper is a device used to perform an...

  15. 21 CFR 870.4875 - Intraluminal artery stripper.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Intraluminal artery stripper. 870.4875 Section 870...) MEDICAL DEVICES CARDIOVASCULAR DEVICES Cardiovascular Surgical Devices § 870.4875 Intraluminal artery stripper. (a) Identification. An intraluminal artery stripper is a device used to perform an...

  16. 21 CFR 870.4875 - Intraluminal artery stripper.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Intraluminal artery stripper. 870.4875 Section 870...) MEDICAL DEVICES CARDIOVASCULAR DEVICES Cardiovascular Surgical Devices § 870.4875 Intraluminal artery stripper. (a) Identification. An intraluminal artery stripper is a device used to perform an...

  17. Nonadditivity of convoy- and secondary-electron yields in the forward-electron emission from thin carbon foils under irradiation of fast carbon-cluster ions

    NASA Astrophysics Data System (ADS)

    Tomita, S.; Yoda, S.; Uchiyama, R.; Ishii, S.; Sasa, K.; Kaneko, T.; Kudo, H.

    2006-06-01

    We have measured energy spectra of secondary electrons produced by fast-carbon-cluster Cn+ (n=1-4) bombardment of thin carbon foils (3.2, 7.3, 11.9, and 20.3μg/cm2 ). For clusters of identical velocity, the convoy-electron yield is enhanced with increasing cluster size n , while the yield of secondary electrons is reduced. The yield of convoy electrons normalized to the number of injected atoms increases proportionally with cluster size n . This proportionality suggests that there is only a weak vicinage effect on the number of primary electrons scattered by the projectile. The vicinage effect observed in low-energy secondary electrons must therefore arise from either transport or transmission through the surface.

  18. Composite heat pipe development status: Development of lightweight prototype carbon-carbon heat pipe with integral fins and metal foil liner

    NASA Technical Reports Server (NTRS)

    Juhasz, Albert J.; Rovang, Richard D.

    1995-01-01

    This report discusses development and proof-of-concept testing of a new lightweight carbon-carbon (C-C) space radiator heat pipe, carried out under the NASA Civil Space Technology Initiative (CSTI) High Capacity Power Program. The prototype heat pipe, equipped with a niobium-zirconium foil liner, was filled with potassium working fluid and tested for 11 hours, including startup from ambient temperature with the working fluid initially in the frozen state to near 700 K condenser temperature. Steady-state heat pipe input power during testing was facility limited to about 300 watts. Post test inspection showed the heat pipe to be in excellent condition after eight thermal cycles from ambient to steady-state operating temperature. Utilization of other liner materials and working fluids would greatly extend the spectrum of service temperatures for this technology, with potential applications ranging from small spacecraft heat rejection to aircraft and terrestrial uses.

  19. ADVANCED TECHNOLOGIES FOR STRIPPER GAS WELL ENHANCEMENT

    SciTech Connect

    C.M. Boyer II; N.R. Fairchild, Jr.

    2000-04-01

    As part of Task 1 in the Advanced Technologies for Stripper Gas Well Enhancement, Holditch-Reservoir Technologies has partnered with two Appalachian Basin producers, Great Lakes Energy (formerly Range Resources) and Belden & Blake Corporation, to develop methodologies for the identification and enhancement of stripper wells with economic upside potential. The industry partners have provided data for over 700 wells in northwest Pennsylvania. The Task 1 goals of this project are to develop and validate methodologies that can quickly and cost effectively identify wells with enhancement potential. We are currently working with the well data supplied by the industry partners to develop and validate these methodologies.

  20. Charge Strippers of Heavy Ions for High Intensity Accelerators

    NASA Astrophysics Data System (ADS)

    Nolen, Jerry A.; Marti, Felix

    2014-02-01

    Charge strippers play a critical role in many high intensity heavy ion accelerators. Here we present some history of recent stripper technology development and indicate the capabilities and limitations of the various approaches. The properties of solid, gaseous, and liquid strippers are covered. In particular, the limitations of solid strippers for high intensity, high atomic number heavy ions and the unique features of helium gas and liquid lithium for high intensity applications are covered. The need for high quality simulation of stripper performance as important input for system optimization is explained and examples of the current simulation codes are given.

  1. Evaluation of a cotton stripper yield monitor

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The objective of this work was to evaluate the accuracy of a microwave sensor based yield monitor for measuring yield on a cotton stripper harvester and determine if the yield monitor can discriminate differences in yield to the same level as a reference scale system. A new yield monitor was instal...

  2. Sulphur hexafluoride as a stripper gas for tandem accelerators

    NASA Astrophysics Data System (ADS)

    Hotchkis, M. A. C.; Child, D.; Fink, D.; Garton, D.; Levchenko, V.; Wilcken, K.

    2013-05-01

    We have investigated sulphur hexafluoride as a stripper gas in tandem accelerators by using the ANTARES accelerator system at ANSTO to measure charge state distributions for this gas. Results are reported at 4 MV terminal voltage for injected negative ions ranging from carbon to uranium oxide. For iodine and thorium the distributions are extended across a range of energies of practical use for accelerator mass spectrometry, ion beam analysis and other accelerator applications. Charge state distributions using sulphur hexafluoride are found to have mean charge states up to 1 charge unit higher than, and to be broader than, corresponding distributions for argon gas, except in the case of carbon beams. As a result, SF6 is shown to provide significantly higher yields for charge states of heavy ions above the mean charge state. We now perform actinide AMS measurements with 9% yield to the 5+ charge state, compared to 4-5% achieved previously with argon gas.

  3. Hydrogen in carbon foils made by DC glow discharge in ethylene

    NASA Astrophysics Data System (ADS)

    Bailey, P.; Armour, D. G.; England, J. B. A.; Tait, N. R. S.; Tolfree, D. W. L.

    1983-08-01

    Thermal desorption has been studied from thin films of carbon prepared by dc glow discharge in ethylene. The only gases released in significant quantities are hydrogen and methane. Both releases can be characterised by a continuum of activation energies but the methane release peaks at a lower temperature than that from hydrogen. The estimated total hydrogen release is compared with the hydrogen content determined by nuclear scattering experiments. Infra red studies suggest that the majority of CH 2 and CH 3 bonds can be ruptured by annealing at 300°C, a temperature well below the hydrogen and methane release rate maxima. Possible hydrogen bonding modes and desorption mechanisms are discussed.

  4. Equilibrium and non-equilibrium charge-state distributions of 2 MeV/u sulfur ions passing through carbon foils

    NASA Astrophysics Data System (ADS)

    Imai, M.; Sataka, M.; Kawatsura, K.; Takahiro, K.; Komaki, K.; Shibata, H.; Sugai, H.; Nishio, K.

    2009-08-01

    Both equilibrium and non-equilibrium charge-state distributions for 2.0 MeV/u sulfur ions after passing through carbon foils were studied experimentally. For the equilibrium charge-state distribution, incident ions of S 7+, S 12+, S 14+ and S 16+ were injected into carbon foils 54, 98, 150 and 200 μg/cm 2 in thickness, whereas for the non-equilibrium distributions, new measurements for S 15+ and S 16+ incidences were made through carbon foils of 0.9-10 μg/cm 2 to supplement our previous experiments regarding S 6+-S 14+ incidences [M. Imai, M. Sataka, K. Kawatsura, K. Takahiro, K. Komaki, H. Shibata, H. Sugai, K. Nishio, Nucl. Instr. and Meth. B 230 (2005) 63; M. Imai, M. Sataka, K. Kawatsura, K. Takahiro, K. Komaki, H. Shibata, H. Sugai, K. Nishio, Nucl. Instr. and Meth. B 256 (2007) 11]. Mean charge states for S 6+-S 14+ incidences as functions of the penetration thickness merged at 6.9 μg/cm 2 and changed together until reaching equilibrium at around 100 μg/cm 2, while those for S 15+ and S 16+ incidences took different paths to equilibrium, which was also the case for distribution widths for S 6+-S 14+, S 15+ and S 16+ incidences. An equilibrium mean charge state of 12.68 and distribution width of 1.11 were attained with equilibrium charge distributions between 6+ and 16+.

  5. Consortium for Petroleum & Natural Gas Stripper Wells

    SciTech Connect

    Joel L. Morrison; Sharon L. Elder

    2007-03-31

    The Pennsylvania State University, under contract to the U.S. Department of Energy (DOE), National Energy Technology Laboratory (NETL), established a national industry-driven Stripper Well Consortium (SWC) that is focused on improving the production performance of domestic petroleum and/or natural gas stripper wells. The SWC represents a partnership between U.S. petroleum and natural gas producers, trade associations, state funding agencies, academia, and the NETL. This document serves as the twelfth quarterly technical progress report for the SWC. Key activities for this reporting period included: (1) Drafting and releasing the 2007 Request for Proposals; (2) Securing a meeting facility, scheduling and drafting plans for the 2007 Spring Proposal Meeting; (3) Conducting elections and announcing representatives for the four 2007-2008 Executive Council seats; (4) 2005 Final Project Reports; (5) Personal Digital Assistant Workshops scheduled; and (6) Communications and outreach.

  6. ADVANCED TECHNOLOGIES FOR STRIPPER GAS WELL ENHANCEMENT

    SciTech Connect

    C.M. Boyer II; N.R. Fairchild, Jr.; R.J. MacDonald P.G.

    2001-01-01

    As part of Task 1 in the Advanced Technologies for Stripper Gas Well Enhancement, Schlumberger--Holditch Reservoir Technologies (H-RT) has partnered with two Appalachian Basin producers, Great Lakes Energy (formerly Range Resources) and Belden and Blake Corporation, to develop methodologies for the identification and enhancement of stripper wells with economic upside potential. These industry partners have provided data for over 700 wells in northwestern Pennsylvania. Phase 1 goals of this project are to develop and validate methodologies that can quickly and cost-effectively identify wells with enhancement potential. We are currently in the final stages of developing and testing our new Access/Excel based software and processing this well data to generate a list of potential candidate wells that can be used in Phase 2 to validate these methodologies. Preparation of the Final Technical report has begun.

  7. ADVANCED TECHNOLOGIES FOR STRIPPER GAS WELL ENHANCEMENT

    SciTech Connect

    C.M. Boyer II; N.R. Fairchild, Jr.; R.J. MacDonald P.G.

    2000-10-01

    As part of Task 1 in the Advanced Technologies for Stripper Gas Well Enhancement, Schlumberger--Holditch Reservoir Technologies (H-RT) has partnered with two Appalachian Basin producers, Great Lakes Energy (formerly Range Resources) and Belden and Blake Corporation, to develop methodologies for the identification and enhancement of stripper wells with economic upside potential. These industry partners have provided data for over 700 wells in northwestern Pennsylvania. Phase 1 goals of this project are to develop and validate methodologies that can quickly and cost-effectively identify wells with enhancement potential. We are currently in the final stages of developing and testing our new Access/Excel based software and processing this well data to generate a list of potential candidate wells that can be used in Phase 2 to validate these methodologies.

  8. ADVANCED TECHNOLOGIES FOR STRIPPER GAS WELL ENHANCEMENT

    SciTech Connect

    C.M. Boyer II; N.,R. Fairchild, Jr.; R.J. MacDonald P.G.

    2000-10-01

    As part of Phase 1 in the Advanced Technologies for Stripper Gas Well Enhancement, Schlumberger--Holditch Reservoir Technologies (H-RT) has partnered with two Appalachian Basin producers, Great Lakes Energy (formerly Range Resources) and Belden & Blake Corporation, to develop methodologies for the identification and enhancement of stripper wells with economic upside potential. These industry partners have provided data for over 700 wells in northwestern Pennsylvania. Phase 1 goals of this project are to develop and validate methodologies that can quickly and cost-effectively identify wells with enhancement potential. We are currently processing the production and well data and developing our new Access/Excel based software that incorporates our identification methodologies. Upon completion we will generate a list of potential candidate wells that can be used in Phase 2 to validate these methodologies.

  9. ADVANCED TECHNOLOGIES FOR STRIPPER GAS WELL ENHANCEMENT

    SciTech Connect

    Charles M. Boyer II; Ronald J. MacDonald

    2002-07-01

    As part of Task 1 in Advanced Technologies for Stripper Gas Well Enhancement, Schlumberger-Holditch Reservoir Technologies (H-RT) joined with two Appalachian Basin producers, Great Lakes Energy Partners, LLC, and Belden & Blake Corporation to develop methodologies for identification and enhancement of stripper wells with economic upside potential. These industry partners previously provided us with data for more than 700 wells in northwestern Pennsylvania. Phase 1 goals of this project are to develop and validate methodologies that can quickly and cost-effectively identify wells with enhancement potential. We have enhanced and streamlined our software, and we are using the final version of our new Microsoft{trademark} Access/Excel based software. We have processed all well information and identified potential candidate wells that can be used in Phase 2 to validate the new methodologies. In addition, the final technical report is almost finished and a draft version has been reviewed by DOE.

  10. Equilibrium and non-equilibrium charge-state distributions of 2.0 MeV/u carbon ions passing through carbon foils

    NASA Astrophysics Data System (ADS)

    Imai, M.; Sataka, M.; Matsuda, M.; Okayasu, S.; Kawatsura, K.; Takahiro, K.; Komaki, K.; Shibata, H.; Nishio, K.

    2015-07-01

    Both equilibrium and non-equilibrium charge-state distributions were studied experimentally for 2.0 MeV/u carbon ions after passing through carbon foils. Measured charge-state distribution established the equilibrium at a target thickness of 10 μg/cm2 and this remained unchanged until a maximum target thickness of 98 μg/cm2. The equilibrium charge-state distribution, the equilibrium mean charge-state, and the width and skewness of the equilibrium distribution were compared with predictions using existing semi-empirical formulae as well as simulation results, including the ETACHA code. It was found that charge-state distributions, mean charge states, and distribution widths for C2+, C3+, and C4+ incident ions merged into quasi-equilibrium values at a target thickness of 5.7 μg/cm2 in the pre-equilibrium region and evolved simultaneously to the 'real equilibrium' values for all of the initial charge states, including C5+ and C6+ ions, as previously demonstrated for sulfur projectile ions at the same velocity (Imai et al., 2009). Two kinds of simulation, ETACHA and solution of rate equations taking only single electron transfers into account, were used, and both of them reproduced the measured charge evolution qualitatively. The quasi-equilibrium behavior could be reproduced with the ETACHA code, but not with solution of elementary rate equations.

  11. Foil bearings

    NASA Technical Reports Server (NTRS)

    Elrod, David A.

    1993-01-01

    The rolling element bearings (REB's) which support many turbomachinery rotors offer high load capacity, low power requirements, and durability. Two disadvantages of REB's are: (1) rolling or sliding contact within the bearing has life-limiting consequences; and (2) REB's provide essentially no damping. The REB's in the Space Shuttle Main Engine (SSME) turbopumps must sustain high static and dynamic loads, at high speeds, with a cryogenic fluid as lubricant and coolant. The pump end ball bearings limit the life of the SSME high pressure oxygen turbopump (HPOTP). Compliant foil bearing (CFB) manufacturers have proposed replacing turbopump REB's with CFB's CFB's work well in aircraft air cycle machines, auxiliary power units, and refrigeration compressors. In a CFB, the rotor only contracts the foil support structure during start up and shut down. CFB damping is higher than REB damping. However, the load capacity of the CFB is low, compared to a REB. Furthermore, little stiffness and damping data exists for the CFB. A rotordynamic analysis for turbomachinery critical speeds and stability requires the input of bearing stiffness and damping coefficients. The two basic types of CFB are the tension-dominated bearing and the bending-dominated bearing. Many investigators have analyzed and measured characteristics of tension-dominated foil bearings, which are applied principally in magnetic tape recording. The bending-dominated CFB is used more in rotating machinery. This report describes the first phase of a structural analysis of a bending-dominated, multileaf CFB. A brief discussion of CFB literature is followed by a description and results of the present analysis.

  12. Consortium for Petroleum & Natural Gas Stripper Wells

    SciTech Connect

    Morrison, Joel

    2011-12-01

    The United States has more oil and gas wells than any other country. As of December 31, 2004, there were more than half a million producing oil wells in the United States. That is more than three times the combined total for the next three leaders: China, Canada, and Russia. The Stripper Well Consortium (SWC) is a partnership that includes domestic oil and gas producers, service and supply companies, trade associations, academia, the Department of Energy’s Strategic Center for Natural Gas and Oil (SCNGO) at the National Energy Technology Laboratory (NETL), and the New York State Energy Research and Development Authority (NYSERDA). The Consortium was established in 2000. This report serves as a final technical report for the SWC activities conducted over the May 1, 2004 to December 1, 2011 timeframe. During this timeframe, the SWC worked with 173 members in 29 states and three international countries, to focus on the development of new technologies to benefit the U.S. stripper well industry. SWC worked with NETL to develop a nationwide request-for-proposal (RFP) process to solicit proposals from the U.S. stripper well industry to develop and/or deploy new technologies that would assist small producers in improving the production performance of their stripper well operations. SWC conducted eight rounds of funding. A total of 132 proposals were received. The proposals were compiled and distributed to an industry-driven SWC executive council and program sponsors for review. Applicants were required to make a formal technical presentation to the SWC membership, executive council, and program sponsors. After reviewing the proposals and listening to the presentations, the executive council made their funding recommendations to program sponsors. A total of 64 projects were selected for funding, of which 59 were fully completed. Penn State then worked with grant awardees to issue a subcontract for their approved work. SWC organized and hosted a total of 14 meetings

  13. Lithium ion batteries made of electrodes with 99 wt% active materials and 1 wt% carbon nanotubes without binder or metal foils

    NASA Astrophysics Data System (ADS)

    Hasegawa, Kei; Noda, Suguru

    2016-07-01

    Herein, we propose lithium ion batteries (LIBs) without binder or metal foils, based on a three-dimensional carbon nanotube (CNT) current collector. Because metal foils occupy 20-30 wt% of conventional LIBs and the polymer binder has no electrical conductivity, replacing such non-capacitive materials is a valid approach for improving the energy and power density of LIBs. Adding only 1 wt% of few-wall CNTs to the active material enables flexible freestanding sheets to be fabricated by simple dispersion and filtration processes. Coin cell tests are conducted on full cells fabricated from a 99 wt% LiCoO2-1 wt% CNT cathode and 99 wt% graphite-1 wt% CNT anode. Discharge capacities of 353 and 306 mAh ggraphite-1 are obtained at charge-discharge rates of 37.2 and 372 mA ggraphite-1, respectively, with a capacity retention of 65% at the 500th cycle. The suitability of the 1 wt% CNT-based composite electrodes for practical scale devices is demonstrated with laminate cells containing 50 × 50 mm2 electrodes. Use of metal combs instead of metal foils enables charge-discharge operation of the laminate cell without considerable IR drop. Such electrodes will minimize the amount of metal and maximize the amount of active materials contained in LIBs.

  14. Proof of concept for a novel, binder-free and conducting carbon-free sulfur battery cathode: Composite electroformation of copper foil with incorporated polythiophene wrapped sulfur particles

    NASA Astrophysics Data System (ADS)

    Erhardt, Claudia; Sörgel, Şeniz; Meinhard, Sandra; Sörgel, Timo

    2015-11-01

    This work, for the first time, presents sulfur electrodes for lithium/sulfur (Li/S) batteries produced by a newly developed single-step electroforming process, which allows simultaneous sulfur incorporation during electroformation of an electrically conducting electrode. This metal is used as binding matrix for the sulfur particles and thereby makes any binder and conducting carbon additives redundant. Furthermore, it serves by itself as the current collector, so that all functionalities (current collector, binder and electrical conductor towards sulfur) are fulfilled by the electroformed metal, while modified sulfur particles are directly incorporated (composite electroformation). In this way, the sulfur cathode can be produced in a single continuous step in form of a metal foil with adjustable thickness and sulfur loading. The process requires functionalization of sulfur to improve its wettability, incorporation homogeneity and volume which is provided by wrapping sulfur particles with polythiophene. Electroformed copper-sulfur composite foils are chosen as a first proof of the new concept. The achieved battery capacity, cycling stability and coulombic efficiency are presented. It is shown that the electroformed copper-sulfur composite foil operates very well as a battery cathode and a discharge capacity of over 400 mAh g-1 at a rate of 0.5 C over 100 cycles is preserved.

  15. Foil Electron Multiplier

    DOEpatents

    Funsten, Herbert O.; Baldonado, Juan R.; Dors, Eric E.; Harper, Ronnie W.; Skoug, Ruth M.

    2006-03-28

    An apparatus for electron multiplication by transmission that is designed with at least one foil having a front side for receiving incident particles and a back side for transmitting secondary electrons that are produced from the incident particles transiting through the foil. The foil thickness enables the incident particles to travel through the foil and continue on to an anode or to a next foil in series with the first foil. The foil, or foils, and anode are contained within a supporting structure that is attached within an evacuated enclosure. An electrical power supply is connected to the foil, or foils, and the anode to provide an electrical field gradient effective to accelerate negatively charged incident particles and the generated secondary electrons through the foil, or foils, to the anode for collection.

  16. 43 CFR 3103.4-2 - Stripper well royalty reductions.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 43 Public Lands: Interior 2 2013-10-01 2013-10-01 false Stripper well royalty reductions. 3103.4-2 Section 3103.4-2 Public Lands: Interior Regulations Relating to Public Lands (Continued) BUREAU OF LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) OIL AND GAS LEASING Fees, Rentals and Royalty § 3103.4-2 Stripper well...

  17. ADVANCED TECHNOLOGIES FOR STRIPPER GAS WELL ENHANCEMENT

    SciTech Connect

    Charles M. Boyer II; Ronald J. MacDonald P.G.

    2002-01-01

    As part of Task 1 in Advanced Technologies for Stripper Gas Well Enhancement, Schlumberger-Holditch Reservoir Technologies (H-RT) has joined with two Appalachian Basin producers, Great Lakes Energy Partners, LLC, and Belden & Blake Corporation to develop methodologies for identification and enhancement of stripper wells with economic upside potential. These industry partners have provided us with data for more than 700 wells in northwestern Pennsylvania. Phase 1 goals of this project are to develop and validate methodologies that can quickly and cost-effectively identify wells with enhancement potential. We have continued to enhance and streamline our software, and we are testing the final stages of our new Microsoft{trademark} Access/Excel based software. We are continuing to process the information and are identifying potential candidate wells that can be used in Phase 2 to validate the new methodologies. In addition, preparation of the final technical report is underway. During this quarter, we have presented our project and discussed the software to numerous Petroleum Technology Transfer Council (PTTC) workshops located in various regions of the United States.

  18. Consortium for Petroleum & Natural Gas Stripper Wells

    SciTech Connect

    Joel L. Morrison; Sharon L. Elder

    2006-12-31

    The Pennsylvania State University, under contract to the U.S. Department of Energy (DOE), National Energy Technology Laboratory (NETL), established a national industry-driven Stripper Well Consortium (SWC) that is focused on improving the production performance of domestic petroleum and/or natural gas stripper wells. The SWC represents a partnership between U.S. petroleum and natural gas producers, trade associations, state funding agencies, academia, and the NETL. This document serves as the eleventh quarterly technical progress report for the SWC. Key activities for this reporting period included: (1) Organizing and hosting the Fall SWC Technology Transfer Workshop for the northeastern U.S., in Pittsburgh, PA, on November 9, 2006, and organizing and identifying projects to exhibit during the SWC/Gas Storage Technology Consortium (GSTC) joint reception on November 8, 2006; (2) Distributing a paper copy of the Texas Tech 2004 Final Report and a revised, complete compact disc of all 2004 final reports; (3) Invoicing current and potential members for FY2007; (4) Soliciting nominations for the 2007-2008 Executive Council seats; and (5) Communications and outreach.

  19. Consortium for Petroleum & Natural Gas Stripper Wells

    SciTech Connect

    Joel L. Morrison; Sharon L. Elder

    2006-09-30

    The Pennsylvania State University, under contract to the U.S. Department of Energy (DOE), National Energy Technology Laboratory (NETL) established a national industry-driven Stripper Well Consortium (SWC) that is focused on improving the production performance of domestic petroleum and/or natural gas stripper wells. The consortium creates a partnership with the U.S. petroleum and natural gas producers, trade associations, state funding agencies, academia, and the National Energy Technology Laboratory. This report serves as the tenth quarterly technical progress report for the SWC. Key activities for this reporting period include: {lg_bullet} 2004 SWC Final Project Reports distribution; {lg_bullet} Exhibit and present at the Midcontinent Oil and Gas Prospect Fair, Great Bend, KS, September 12, 2006; {lg_bullet} Participate and showcase current and past projects at the 2006 Oklahoma Oil and Gas Trade Expo, Oklahoma City, OK, October 26, 2006; {lg_bullet} Finalize agenda and identify exhibitors for the northeastern US, Fall SWC Technical Transfer Workshop, Pittsburghhh, PA, November 9, 2006; {lg_bullet} Continue distribution of the public broadcast documentary, ''Independent Oil: Rediscovering American's Forgotten Wells''; {lg_bullet} Communications/outreach; and {lg_bullet} New members update.

  20. Improved liquid-film electron stripper

    DOEpatents

    Gavin, B.F.

    1984-11-01

    An improved liquid-film electron stripper particularly for high intensity heavy ion beams which produces constant regenerated, stable, free-standing liquid films having an adjustable thickness between 0.3 to 0.05 microns. The improved electron stripper is basically composed of at least one high speed, rotating disc with a very sharp, precision-like, ground edge on one side of the disc's periphery and with highly polished, flat, radial surface adjacent the sharp edge. A fine stream of liquid, such as oil, impinges at a 90/sup 0/ angle adjacent the disc's sharp outer edge. Film terminators, located at a selected distance from the disc perimeter are positioned approximately perpendicular to the film. The terminators support, shape, and stretch the film and are arranged to assist in the prevention of liquid droplet formation by directing the collected film to a reservoir below without breaking or interfering with the film. One embodiment utilizes two rotating discs and associated terminators, with the discs rotating so as to form films in opposite directions, and with the second disc being located down beam-line relative to the first disc.

  1. ADVANCED TECHNOLOGIES FOR STRIPPER GAS WELL ENHANCEMENT

    SciTech Connect

    Ronald J. MacDonald

    2003-04-01

    As part of Task 1 in Advanced Technologies for Stripper Gas Well Enhancement, Schlumberger Data & Consulting Services (DCS) joined with two Appalachian Basin producers, Great Lakes Energy Partners, LLC, and Belden & Blake Corporation to develop methodologies for identification and enhancement of stripper wells with economic upside potential. These industry partners previously provided us with data for more than 700 wells in northwestern Pennsylvania. Phase 1 goals of this project are to develop and validate methodologies that can quickly and cost-effectively identify wells with enhancement potential. We have enhanced and streamlined our software, and we are using the final version of our new Microsoft{trademark} Access/Excel programs. During the last quarter of 2002, we received additional data for approximately 2,200 wells from Great Lakes. This information pertains to their Cooperstown field located in northwestern Pennsylvania. We recognized approximately 130 potential remediation candidates, and Great Lakes' personnel are currently reviewing this list for viable remediation. This field has provided a rigorous test of our software and analytical methods. We have processed all the information provided to us including the Cooperstown data. Great Lakes also provided supplemental data listing the original operator of the wells. We are also determining whether a statistically significant number of underperformers correlate to specific operators and/or their associated completion/stimulation methods. In addition, the DOE has reviewed a draft version of a final report.

  2. ADVANCED TECHNOLOGIES FOR STRIPPER GAS WELL ENHANCEMENT

    SciTech Connect

    Ronald J. MacDonald

    2003-01-01

    As part of Task 1 in Advanced Technologies for Stripper Gas Well Enhancement, Schlumberger Data & Consulting Services (DCS) joined with two Appalachian Basin producers, Great Lakes Energy Partners, LLC, and Belden & Blake Corporation to develop methodologies for identification and enhancement of stripper wells with economic upside potential. These industry partners previously provided us with data for more than 700 wells in northwestern Pennsylvania. Phase 1 goals of this project are to develop and validate methodologies that can quickly and cost-effectively identify wells with enhancement potential. We have enhanced and streamlined our software, and we are using the final version of our new Microsoft{trademark} Access/Excel based software. We have received additional data from Great Lakes pertaining to a Cooperstown field that is expected to have numerous remediation candidates. This field will provide a rigorous test of out software and analytical methods. We have processed all the information provided to us before receiving the Cooperstown data and are currently analyzing the new data. Great Lakes will be providing supplemental data in the near future that will identify the original operator of the wells. This will prove valuable in determining whether a statistically significant number of underperformers are a result of specific operators and their associated completion/stimulation methods. We have identified potential candidate wells for Phase 2 to validate the new methodologies. In addition, a draft version of a final report has been reviewed by DOE.

  3. ADVANCED TECHNOLOGIES FOR STRIPPER GAS WELL ENHANCEMENT

    SciTech Connect

    Ronald J. MacDonald

    2005-04-27

    As part of Task 1 in Advanced Technologies for Stripper Gas Well Enhancement, Schlumberger Data & Consulting Services (DCS) joined with two Appalachian Basin producers, Great Lakes Energy Partners, LLC, and Belden & Blake Corporation to develop methodologies for identification and enhancement of stripper wells with economic upside potential. These industry partners previously provided us with data for more than 700 wells in northwestern Pennsylvania. Phase 1 goals of this project were to develop and validate methodologies that can quickly and cost-effectively identify underperforming wells with remediation potential. We enhanced and streamlined our software and are using it with Microsoft's{trademark} Access and Excel programs. During the last quarter of 2002, Great Lakes provided us with additional data for approximately 2,200 wells located in their Cooperstown field situated in northwestern Pennsylvania. We identified approximately 220 potential remediation candidates and Great Lakes personnel reviewed this list for viability and selected more than twenty five wells to be reworked. Approximately fifteen wells have been successfully reworked as of year-end 2004. This field provided a rigorous test of our software and analytical methods. We processed all the information provided to us including the Cooperstown data. Great Lakes also provided supplemental data listing the original operator of the wells.

  4. ADVANCED TECHNOLOGIES FOR STRIPPER GAS WELL ENHANCEMENT

    SciTech Connect

    Ronald J. MacDonald

    2004-07-14

    As part of Task 1 in Advanced Technologies for Stripper Gas Well Enhancement, Schlumberger Data & Consulting Services (DCS) joined with two Appalachian Basin producers, Great Lakes Energy Partners, LLC, and Belden & Blake Corporation to develop methodologies for identification and enhancement of stripper wells with economic upside potential. These industry partners previously provided us with data for more than 700 wells in northwestern Pennsylvania. Phase 1 goals of this project are to develop and validate methodologies that can quickly and cost-effectively identify underperforming wells with remediation potential. We have enhanced and streamlined our software and are using it with the latest versions of Microsoft's{trademark} Access and Excel programs. During the last quarter of 2002, Great Lakes provided us with additional data for approximately 2,200 wells located in their Cooperstown field situated in northwestern Pennsylvania. We identified approximately 130 potential remediation candidates, and Great Lakes personnel are currently reviewing this list for viable remediation. Within the last few weeks, a list of five candidates have been chosen for refract, in addition to two alternate wells. This field has provided a rigorous test of our software and analytical methods. We have processed all the information provided to us including the Cooperstown data. Great Lakes also provided supplemental data listing the original operator of the wells. We have determined whether a statistically significant number of underperformers correlate to specific operators and/or their associated completion/stimulation methods. In addition, the DOE has reviewed a draft version of a final report.

  5. ADVANCED TECHNOLOGIES FOR STRIPPER GAS WELL ENHANCEMENT

    SciTech Connect

    Ronald J. MacDonald

    2003-04-04

    As part of Task 1 in Advanced Technologies for Stripper Gas Well Enhancement, Schlumberger Data & Consulting Services (DCS) joined with two Appalachian Basin producers, Great Lakes Energy Partners, LLC, and Belden & Blake Corporation to develop methodologies for identification and enhancement of stripper wells with economic upside potential. These industry partners previously provided us with data for more than 700 wells in northwestern Pennsylvania. Phase 1 goals of this project are to develop and validate methodologies that can quickly and cost-effectively identify wells with enhancement potential. We have enhanced and streamlined our software, and we are using the final version of our new Microsoft{trademark} Access/Excel programs. During the last quarter of 2002, we received additional data for approximately 2,200 wells from Great Lakes. This information pertains to their Cooperstown field located in northwestern Pennsylvania. We recognized approximately 130 potential remediation candidates, and Great Lakes' personnel are currently reviewing this list for viable remediation. This field has provided a rigorous test of our software and analytical methods. We have processed all the information provided to us including the Cooperstown data. Great Lakes also provided supplemental data listing the original operator of the wells. We have determined whether a statistically significant number of underperformers correlate to specific operators and/or their associated completion/stimulation methods. In addition, the DOE has reviewed a draft version of a final report.

  6. ADVANCED TECHNOLOGIES FOR STRIPPER GAS WELL ENHANCEMENT

    SciTech Connect

    Ronald J. MacDonald

    2002-11-01

    As part of Task 1 in Advanced Technologies for Stripper Gas Well Enhancement, Schlumberger Data & Consulting Services (DCS) joined with two Appalachian Basin producers, Great Lakes Energy Partners, LLC, and Belden & Blake Corporation to develop methodologies for identification and enhancement of stripper wells with economic upside potential. These industry partners previously provided us with data for more than 700 wells in northwestern Pennsylvania. Phase 1 goals of this project are to develop and validate methodologies that can quickly and cost-effectively identify wells with enhancement potential. We have enhanced and streamlined our software, and we are using the final version of our new Microsoft{trademark} Access/Excel based software. We have received additional data from Great Lakes pertaining to a Cooperstown field that is expected to have numerous remediation candidates. This field will provide a rigorous test of out software and analytical methods. We have processed all the information available to us before the Cooperstown data was provided. We have identified potential candidate wells that can be used in Phase 2 to validate the new methodologies. In addition, a draft version of a final report has been reviewed by DOE.

  7. U2 8 + -intensity record applying a H2 -gas stripper cell

    NASA Astrophysics Data System (ADS)

    Barth, Winfried; Adonin, Aleksey; Düllmann, Christoph E.; Heilmann, Manuel; Hollinger, Ralph; Jäger, Egon; Khuyagbaatar, Jadambaa; Krier, Joerg; Scharrer, Paul; Vormann, Hartmut; Yakushev, Alexander

    2015-04-01

    To meet the Facility for Antiproton and Ion Research science requirements higher beam intensity has to be achieved in the present GSI-accelerator complex. For this an advanced upgrade program for the UNILAC is ongoing. Stripping is a key technology for all heavy ion accelerators. For this an extensive research and development program was carried out to optimize for high brilliance heavy ion operation. After upgrade of the supersonic N2 -gas jet (2007), implementation of high current foil stripping (2011) and preliminary investigation of H2 -gas jet operation (2012), recently (2014) a new H2 -gas cell using a pulsed gas regime synchronized with arrival of the beam pulse has been developed. An obviously enhanced stripper gas density as well as a simultaneously reduced gas load for the pumping system result in an increased stripping efficiency, while the beam emittance remains the same. A new record intensity (7.8 emA) for 238U2 8 + beams at 1.4 MeV /u has been achieved applying the pulsed high density H2 stripper target to a high intensity 238U4 + beam from the VARIS ion source with a newly developed extraction system. The experimental results are presented in detail.

  8. Foil changing apparatus

    DOEpatents

    Crist, Charles E.; Ives, Harry C.; Leifeste, Gordon T.; Miller, Robert B.

    1988-01-01

    A self-contained hermetically sealed foil changer for advancing a portion of foil web into a position normal to the path of a high energy particle beam. The path of the beam is defined generally by an aperture plate and cooperating axially movable barrel such that the barrel can be advanced toward the plate thereby positioning a portion of the foil across the beam path and sealing the foil between the barrel and the plate to form a membrane across said beam path. A spooling apparatus contained in the foil changer permits selectively advancing a fresh supply of foil across the beam path without breaking the foil changer seal.

  9. Combined air stripper/membrane vapor separation systems. [Volatile organic compounds

    SciTech Connect

    Wijmans, J.G.; Baker, R.W.; Kamaruddin, H.D.; Kaschemekat, J.; Olsen, R.P.; Rose, M.E.; Segelke, S.V.

    1992-11-01

    Air stripping is an economical and efficient method of removing dissolved volatile organic compounds (VOCs) from contaminated groundwater. Air strippers, however, produce a vent air stream, which must meet the local air quality limits. If the VOC content exceeds the limits, direct discharge is not possible; therefore, a carbon adsorption VOC capture system is used to treat the vent air. This treatment step adds a cost of at least $50/lb of VOC captured. In this program, a combined air stripper/membrane vapor separation system was constructed and demonstrated in the laboratory. The membrane system captures VOCs from the stripper vent stream at a projected cost of $15/lb VOC for a water VOC content of 5 ppmw, and $75/lb VOC for a water VOC content of 1 ppmw. The VOCs are recovered as a small, concentrated liquid fraction for disposal or solvent recycling. The concept has been demonstrated in experiments with a system capable of handling up to 150,000 gpd of water. The existing demonstration system is available for field tests at a DOE facility or remediation site. Replacement of the current short air stripping tower (effective height 3 m) with a taller tower is recommended to improve VOC removal.

  10. Advanced Technologies For Stripper Gas Well Enhancement

    SciTech Connect

    Ronald J. MacDonald; Charles M. Boyer; Joseph H. Frantz Jr; Paul A. Zyglowicz

    2005-04-01

    Stripper gas and oil well operators frequently face a dilemma regarding maximizing production from low-productivity wells. With thousands of stripper wells in the United States covering extensive acreage, it is difficult to identify easily and efficiently marginal or underperforming wells. In addition, the magnitude of reviewing vast amounts of data places a strain on an operator's work force and financial resources. Schlumberger DCS, in cooperation with the National Energy Technology Laboratory (NETL) and the U.S. Department of Energy (DOE), has created software and developed in-house analysis methods to identify remediation potential in stripper wells relatively easily. This software is referred to as Stripper Well Analysis Remediation Methodology (SWARM). SWARM was beta-tested with data pertaining to two gas fields located in northwestern Pennsylvania and had notable results. Great Lakes Energy Partners, LLC (Great Lakes) and Belden & Blake Corporation (B&B) both operate wells in the first field studied. They provided data for 729 wells, and we estimated that 41 wells were candidates for remediation. However, for reasons unbeknownst to Schlumberger these wells were not budgeted for rework by the operators. The second field (Cooperstown) is located in Crawford, Venango, and Warren counties, Pa and has more than 2,200 wells operated by Great Lakes. This paper discusses in depth the successful results of a candidate recognition study of this area. We compared each well's historical production with that of its offsets and identified 339 underperformers before considering remediation costs, and 168 economically viable candidates based on restimulation costs of $50,000 per well. From this data, we prioritized a list based on the expected incremental recoverable gas and 10% discounted net present value (NPV). For this study, we calculated the incremental gas by subtracting the volumes forecasted after remediation from the production projected at its current

  11. Tritium glovebox stripper system seismic design evaluation

    SciTech Connect

    Grinnell, J. J.; Klein, J. E.

    2015-09-01

    The use of glovebox confinement at US Department of Energy (DOE) tritium facilities has been discussed in numerous publications. Glovebox confinement protects the workers from radioactive material (especially tritium oxide), provides an inert atmosphere for prevention of flammable gas mixtures and deflagrations, and allows recovery of tritium released from the process into the glovebox when a glovebox stripper system (GBSS) is part of the design. Tritium recovery from the glovebox atmosphere reduces emissions from the facility and the radiological dose to the public. Location of US DOE defense programs facilities away from public boundaries also aids in reducing radiological doses to the public. This is a study based upon design concepts to identify issues and considerations for design of a Seismic GBSS. Safety requirements and analysis should be considered preliminary. Safety requirements for design of GBSS should be developed and finalized as a part of the final design process.

  12. What You Should Know about Using Paint Strippers

    MedlinePlus

    ... evaporate quickly, such as methylene chloride. However, electrical sparks from fans may increase the chance of flammable ... use flammable paint strippers near any source of sparks, flame, or high heat . Do not work near ...

  13. Hot-blade stripper for polyester insulation on FCC

    NASA Technical Reports Server (NTRS)

    Angele, W.; Chambers, C. M.

    1971-01-01

    Stripper incorporates a blade which is electrically heated to a controlled temperature. Heated blade softens and strips insulation from cable while paper ribbon removes insulation material and keeps blade clean for next operation.

  14. Absolute cross sections for binary-encounter electron ejection by 95-MeV/u {sup 36}Ar{sup 18+} penetrating carbon foils

    SciTech Connect

    De Filippo, E.; Lanzano, G.; Aiello, S.; Arena, N.; Geraci, M.; Pagano, A.; Rothard, H.; Volant, C.; Anzalone, A.; Giustolisi, F.

    2003-08-01

    Doubly differential electron velocity spectra induced by 95-MeV/u {sup 36}Ar{sup 18+} from thin carbon foils were measured at GANIL (Caen, France) by means of the ARGOS multidetector and the time-of-flight technique. The spectra allow us to determine absolute singly differential cross sections as a function of the emission angle. Absolute doubly differential cross sections for binary encounter electron ejection from C targets are compared to a transport theory, which is based on the relativistic electron impact approximation for electron production and which accounts for angular deflection, energy loss, and also energy straggling of the transmitted electrons. For the thinnest targets, the measured peak width is in good agreement with experimental data obtained with a different detection technique. The theory underestimates the peak width but provides (within a factor of 2) the correct peak intensity. For the thickest target, even the peak shape is well reproduced by theory.

  15. Effects of pulse voltage and deposition time on the adhesion strength of graded metal/carbon films deposited on bendable stainless steel foils by hybrid cathodic arc - glow discharge plasma assisted chemical vapor deposition

    NASA Astrophysics Data System (ADS)

    Jamesh, Mohammed Ibrahim; Boxman, R. L.; Bilek, Marcela M. M.; Kocer, Cenk; Hu, Tingwei; Zhang, Xuming; McKenzie, David R.; Chu, Paul K.

    2016-03-01

    Graded Ti/C composite films with carbon topcoats are prepared on bendable stainless steel foils by hybrid cathodic arc / glow discharge plasma-assisted chemical vapor deposition to simulate cardiovascular stents. Strong adhesion between the stainless steel substrate and carbon topcoat is achieved due to the graded Ti/C interface and it is further improved by increasing the pulse voltage. Moreover, the graded coating is more hydrophilic than the stainless steel substrate.

  16. Simulation of ion beam scattering in a gas stripper

    NASA Astrophysics Data System (ADS)

    Maxeiner, Sascha; Suter, Martin; Christl, Marcus; Synal, Hans-Arno

    2015-10-01

    Ion beam scattering in the gas stripper of an accelerator mass spectrometer (AMS) enlarges the beam phase space and broadens its energy distribution. As the size of the injected beam depends on the acceleration voltage through phase space compression, the stripper becomes a limiting factor of the overall system transmission especially for low energy AMS system in the sub MV region. The spatial beam broadening and collisions with the accelerator tube walls are a possible source for machine background and energy loss fluctuations influence the mass resolution and thus isotope separation. To investigate the physical processes responsible for these effects, a computer simulation approach was chosen. Monte Carlo simulation methods are applied to simulate elastic two body scattering processes in screened Coulomb potentials in a (gas) stripper and formulas are derived to correctly determine random collision parameters and free path lengths for arbitrary (and non-homogeneous) gas densities. A simple parametric form for the underlying scattering cross sections is discussed which features important scaling behaviors. An implementation of the simulation was able to correctly model the data gained with the TANDY AMS system at ETH Zurich. The experiment covered transmission measurements of uranium ions in helium and beam profile measurements after the ion beam passed through the He-stripper. Beam profiles measured up to very high stripper densities could be understood in full system simulations including the relevant ion optics. The presented model therefore simulates the fundamental physics of the interaction between an ion beam and a gas stripper reliably. It provides a powerful and flexible tool for optimizing existing AMS stripper geometries and for designing new, state of the art low energy AMS systems.

  17. Glovebox stripper system tritium capture efficiency-literature review

    SciTech Connect

    James, D. W.; Poore, A. S.

    2015-09-28

    Glovebox Stripper Systems (GBSS) are intended to minimize tritium emissions from glovebox confinement systems in Tritium facilities. A question was raised to determine if an assumed 99% stripping (decontamination) efficiency in the design of a GBBS was appropriate. A literature review showed the stated 99% tritium capture efficiency used for design of the GBSS is reasonable. Four scenarios were indicated for GBSSs. These include release with a single or dual stage setup which utilizes either single-pass or recirculation for stripping purposes. Examples of single-pass as well as recirculation stripper systems are presented and reviewed in this document.

  18. Effect of stripper conditions on the yield and structure of coke derived from n-Hexadecane

    SciTech Connect

    Mohammed, A.A.H.; McGhee, B.J.; Snape, C.E.

    1996-10-01

    In FCC units, coked catalyst first passes to a steam stripper to remove residual volatiles before being transferred to the regenerator. Entrained products which are symptomatic of incomplete stripping can contribute to the overall level of coke and increase its hydrogen content considerably. To determine how the yields and composition coke varies in FCC as a function of stripper conditions, tests have been conducted ill fluidised-bed reactor using n-hexadecane at 500{degrees}C, a commercial FCC catalyst with stripping times up to 120 min. Coke concentrates have been prepared by demineralisation with hydrofluoric and hydrochloric acids. The inherently quantitative single pulse excitation {sup 13}C NMR technique has been used to derive the total, protonated and non-protonated aromatic carbon concentrations for the coke concentrates. Mass spectrometry las also used to characterise the cokes. The initial coke possesses considerable aliphatic character (carbon aromaticity of 0.80), but the removal of volatiles by stripping gives rise to increases in both aromaticity and aromatic ring size.

  19. Compliant Foil Seal Investigations

    NASA Technical Reports Server (NTRS)

    Proctor, Margaret; Delgado, Irebert

    2003-01-01

    NASA Glenn Research Center has been working with Mohawk Innovative Technology, Inc. (MiTi) to develop a Compliant Foil Seal for use in gas turbine engines. MiTi was awarded phase I and phase II SBIR contracts to analyze, develop, and test foil seals. As part of the Phase II contract, MiTi delivered an 8.5 inch diameter foil seal to NASA GRC for testing. Today I will be presenting some results of testing the 8.5 inch foil seal at NASA.

  20. Vapor-phase polymerization of poly(3,4-ethylenedioxythiophene) (PEDOT) on commercial carbon coated aluminum foil as enhanced electrodes for supercapacitors

    NASA Astrophysics Data System (ADS)

    Tong, Linyue; Skorenko, Kenneth H.; Faucett, Austin C.; Boyer, Steven M.; Liu, Jian; Mativetsky, Jeffrey M.; Bernier, William E.; Jones, Wayne E.

    2015-11-01

    Laminar composite electrodes are prepared for application in supercapacitors using a catalyzed vapor-phase polymerization (VPP) of 3,4-ethylenedioxythiophene (EDOT) on the surface of commercial carbon coated aluminum foil. These highly electrically conducting polymer films provide for rapid and stable power storage per gram at room temperature. The chemical composition, surface morphology and electrical properties are characterized by Raman spectroscopy, scanning electron microscopy (SEM), and conducting atomic force microscopy (C-AFM). A series of electrical measurements including cyclic voltammetry (CV), charge-discharge (CD) and electrochemical impedance spectroscopy are also used to evaluate electrical performance. The processing temperature of VPP shows a significant effect on PEDOT morphology, the degree of orientation and its electrical properties. The relatively high temperature leads to high specific area and large conductive domains of PEDOT layer which benefits the capacitive behavior greatly according to the data presented. Since the substrate is already highly conductive, the PEDOT based composite can be used as electrode materials directly without adding current collector. By this simple and efficient process, PEDOT based composites exhibit specific capacitance up to 134 F g-1 with the polymerization temperature of 110 °C.

  1. Looking east inside of the ingot mold stripper building for ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Looking east inside of the ingot mold stripper building for the 44" slab mill at a row of ingots. A row of ingot molds are pictured east on the left. - U.S. Steel Edgar Thomson Works, 44" Slab Mill, Along Monongahela River, Braddock, Allegheny County, PA

  2. 43 CFR 3103.4-2 - Stripper well royalty reductions.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... seven years after production on which the operator claims a royalty rate reduction for stripper well... assessed in accordance with 30 CFR 218.102. The BLM may terminate a royalty rate reduction if it is... charges will be assessed in accordance with 30 CFR 218.102....

  3. 43 CFR 3103.4-2 - Stripper well royalty reductions.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... seven years after production on which the operator claims a royalty rate reduction for stripper well... assessed in accordance with 30 CFR 218.102. The BLM may terminate a royalty rate reduction if it is... charges will be assessed in accordance with 30 CFR 218.102....

  4. 43 CFR 3103.4-2 - Stripper well royalty reductions.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... seven years after production on which the operator claims a royalty rate reduction for stripper well... assessed in accordance with 30 CFR 218.102. The BLM may terminate a royalty rate reduction if it is... charges will be assessed in accordance with 30 CFR 218.102....

  5. What Do You Really Know About Floor Finishes & Strippers?

    ERIC Educational Resources Information Center

    Wirth, T. J.

    1972-01-01

    An independent testing laboratory reveals the results of comparative studies done on vinyl flooring and the question of to wax or not to wax'' and which waxes work best with what flooring; and provides six evaluation tips on floor strippers. (EA)

  6. Modeling of RTF Glove-Box and Stripper System

    SciTech Connect

    Hsu, R.H.

    2001-03-28

    The glove box-stripper system for the Replacement Tritium Facility (RTF) has been modeled to determine its steady-state performance. To permit comparison, simulations of modified cases were compared with a standard or base case. This paper discusses tests conducted, results obtained and makes recommendations.

  7. 7 CFR 2902.39 - Floor strippers.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... biobased content of at least 78 percent, which shall be based on the amount of qualifying biobased carbon in the product as a percent of the weight (mass) of the total organic carbon in the finished...

  8. Foil Face Seal Testing

    NASA Technical Reports Server (NTRS)

    Munson, John

    2009-01-01

    In the seal literature you can find many attempts by various researchers to adapt film riding seals to the gas turbine engine. None have been successful, potential distortion of the sealing faces is the primary reason. There is a film riding device that does accommodate distortion and is in service in aircraft applications, namely the foil bearing. More specifically a foil thrust bearing. These are not intended to be seals, and they do not accommodate large axial movement between shaft & static structure. By combining the 2 a unique type of face seal has been created. It functions like a normal face seal. The foil thrust bearing replaces the normal primary sealing surface. The compliance of the foil bearing allows the foils to track distortion of the mating seal ring. The foil seal has several perceived advantages over existing hydrodynamic designs, enumerated in the chart. Materials and design methodology needed for this application already exist. Also the load capacity requirements for the foil bearing are low since it only needs to support itself and overcome friction forces at the antirotation keys.

  9. Surface treatment using metal foil liner

    NASA Technical Reports Server (NTRS)

    Garvey, Ray

    1989-01-01

    A metal foil liner can be used to seal large area surfaces. Characteristics of the two-layer foil liner are discussed. Micrographs for foil-to-foil, foil-to-composite, visible seams, and hidden seams are examined.

  10. Beam-foil spectroscopy

    SciTech Connect

    Berry, H.G.; Hass, M.

    1982-01-01

    A brief survey of some applications of beam-foil spectroscopy is presented. Among the topics covered are lifetime and magnetic moment measurements, nuclear alignment, and polarized light production. (AIP)

  11. Foil changer for the Chalk River superconducting cyclotron

    SciTech Connect

    Hoffmann, C.R.; Kilborn, R.I.; Mouris, J.E.; Proulx, D.R.; Weaver, J.F.

    1985-10-01

    Capture of an injected beam in the Chalk River superconducting cyclotron requires that a carbon stripping foil be accurately placed in a dee to intercept the incoming beam. Foil radial position must be precisely adjustable and foils must be easily replaced. A foil changing apparatus has been designed, built and tested to meet these requirements. The main components are a supply magazine, a transport system, and unloading and loading mechanisms. The magazine is on top of the cyclotron. It holds 300 foils and can be isolated from machine vacuum for refilling. Each foil is mounted on a stainless steel frame. A stainless steel roller chain fitted with 33 copper sleeves (shrouds) carries foils, one per shroud, down a dee stem to the midplane. A 12-bit absolute optical shaft encoder senses foil position. To replace a foil a shroud is positioned at the top of the cyclotron, a foil is removed, and another is transferred from the magazine to the empty shroud. Three stepping motors and associated electronics provide mechanical drive and are interfaced with a CAMAC control system.

  12. Stripper property evaluation through the use of value maps

    SciTech Connect

    Moran, S.

    1995-12-31

    Low-production stripper wells constitute a substantial fraction of total oil and gas wells in the US. Stripper properties are often sold by major companies to independent producers or by one independent to another. Many such properties can be evaluated by using the property decline rates, along with cost and price estimates, and the purchasers` targeted rates of return. Computer program programs can do the basic analyses, as well as assess the sensitivity of the property value to alternate assumptions. However, value maps can be constructed that provide almost instantaneous evaluation; these value maps also provide sensitivity assessments very quickly, and provide insights about property values that may not be apparent from computer runs. The paper explains the math behind a value map, its use, and insights gained from its use.

  13. Stripper system performance in the replacement tritium facility

    SciTech Connect

    Heung, L.K.

    1995-01-01

    The Replacement Tritium Facility (RTF) at the Savannah River Site in the United States was designed and built to handle kilogram levels of tritium. The RTF was started up in January 1994. All the design objectives were achieved. To minimize tritium release to the environment, the tritium handling process is installed inside nitrogen-atmosphere gloveboxes. Any tritium that might leak from the process to the gloveboxes is recovered by stripper systems. The tritium concentration in the gloveboxes is normally maintained at below 0.1 Ci/m{sup 3}. During a large tritium leak from the process to the glovebox, the stripper system lowered the tritium concentration in the glovebox from about 8,000 Ci/m{sup 3} to about 100 Ci/m{sup 3} in one hour. After that the tritium concentration decreased very slowly. It required 5 days of stripping before the concentration was down to about 10 Ci/m{sup 3}.

  14. Investigation of Nanodiamond and Silicon Carbide Foils Product for H-Stripping to Support Spallation Neutron Source

    NASA Astrophysics Data System (ADS)

    Harris, Gary; Griffin, James; Vispute, Rd; CIQM Collaboration

    2015-03-01

    Diamond and silicon carbide (SiC) is an ideal material as an H- stripper foil for spallation neutron source (SNS) applications due to their high thermal conductivity, low molecular weight, and strength. Cubic silicon carbide grown on silicon is a material tension stress and the foil does not curl. Polycrystalline diamond is characterized by a high degree of internal stress, which causes the foil to curl when not supported by the substrate. the sic is grown using a RF CVD system. Hot filament chemical vapor deposition (HFCVD) was used to grow diamond on a silicon substrate. In both cases a 1.2 cm diameter window was etched in the silicon using a 1:1:3 solution of hydrofluoric, nitric, and acetic acids so that the diamond of SiC foil would be suspended while being supported on all sides by the silicon. Wax and or photoresist were used as masks to protect the outer silicon from etching. Raman spectroscopy verified the quality of the grown material. Atomic force microscopy (AFM) revealed that the diamond foil originally against the substrate had an average roughness of <6.7 nm while the foil away from the substrate had an average roughness of 13.2 nm. The SiC foils had roughness less than 3 nm. Scanning electron microscopy (SEM) revealed no cracks in the suspended foil. NSF-STC CIQM.

  15. Foil implosion studies on PEGASUS

    SciTech Connect

    Cochrane, J.C.; Bartsch, R.R.; Begay, F.; Kruse, H.W.; Oona, H.; Parker, J.V.; Turchi, P.J.

    1989-01-01

    PEGASUS is a 1.5 MJ capacitor bank facility used in the Los Alamos Trailmaster foil implosion program. The experiments on this facility are to serve as a diagnostic testbed and foil physics benchmark for foil implosions with explosive generators as drivers. During the first year of operation, foil implosions have been driven by discharging the bank directly into a very thin Aluminum 2500 /angstrom/ thick free-standing foil without any pulse sharpening techniques; so-called ''direct drive.''These direct drive experiments have served as initial tests to optimize bank performance and foil implosion experimental techniques. The results to date are presented below. 1 ref., 2 figs.

  16. Proso Millet Harvest: A Comparison of Conventional Harvest and Direct Harvest with a Stripper Header

    Technology Transfer Automated Retrieval System (TEKTRAN)

    This research was conducted to determine if proso millet can be harvested with a stripper header. Stripper headers use extremely fast rotating metal teeth to rip the seed off the plant and leave the majority of residue standing in the field as opposed to cutting off the entire plant and running tha...

  17. 30 CFR 210.155 - What reports must I submit for Federal onshore stripper oil properties?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ..., Gas, and Geothermal Resources § 210.155 What reports must I submit for Federal onshore stripper oil... Management (BLM) under 43 CFR 3103.4-2 must submit Form MMS-4377, Stripper Royalty Rate Reduction Notification, under 43 CFR 3103.4-2(b)(3). (b) Reporting options. You may find Form MMS-4377 on our...

  18. Monolithic exploding foil initiator

    DOEpatents

    Welle, Eric J; Vianco, Paul T; Headley, Paul S; Jarrell, Jason A; Garrity, J. Emmett; Shelton, Keegan P; Marley, Stephen K

    2012-10-23

    A monolithic exploding foil initiator (EFI) or slapper detonator and the method for making the monolithic EFI wherein the exploding bridge and the dielectric from which the flyer will be generated are integrated directly onto the header. In some embodiments, the barrel is directly integrated directly onto the header.

  19. On a thermal analysis of a second stripper for rare isotope accelerator.

    SciTech Connect

    Momozaki, Y.; Nolen, J.; Nuclear Engineering Division

    2008-08-04

    This memo summarizes simple calculations and results of the thermal analysis on the second stripper to be used in the driver linac of Rare Isotope Accelerator (RIA). Both liquid (Sodium) and solid (Titanium and Vanadium) stripper concepts were considered. These calculations were intended to provide basic information to evaluate the feasibility of liquid (thick film) and solid (rotating wheel) second strippers. Nuclear physics calculations to estimate the volumetric heat generation in the stripper material were performed by 'LISE for Excel'. In the thermal calculations, the strippers were modeled as a thin 2D plate with uniform heat generation within the beam spot. Then, temperature distributions were computed by assuming that the heat spreads conductively in the plate in radial direction without radiative heat losses to surroundings.

  20. Process for anodizing aluminum foil

    SciTech Connect

    Ball, J.A.; Scott, J.W.

    1984-11-06

    In an integrated process for the anodization of aluminum foil for electrolytic capacitors including the formation of a hydrous oxide layer on the foil prior to anodization and stabilization of the foil in alkaline borax baths during anodization, the foil is electrochemically anodized in an aqueous solution of boric acid and 2 to 50 ppm phosphate having a pH of 4.0 to 6.0. The anodization is interrupted for stabilization by passing the foil through a bath containing the borax solution having a pH of 8.5 to 9.5 and a temperature above 80/sup 0/ C. and then reanodizing the foil. The process is useful in anodizing foil to a voltage of up to 760 V.

  1. Compliant Foil Seal Investigations

    NASA Technical Reports Server (NTRS)

    Proctor, Margaret; Delgado, Irebert

    2004-01-01

    Room temperature testing of an 8.5 inch diameter foil seal was conducted in the High Speed, High Temperature Turbine Seal Test Rig at the NASA Glenn Research Center. The seal was operated at speeds up to 30,000 rpm and pressure differentials up to 75 psid. Seal leakage and power loss data will be presented and compared to brush seal performance. The failure of the seal and rotor coating at 30,000 rpm and 15 psid will be presented and future development needs discussed.

  2. Submicron, unbacked, shaped metal foils

    SciTech Connect

    Duchane, D.V.; Barthell, B.L.

    1983-01-01

    A method was developed to produce unbacked, shaped metal foils in sub-micron thicknesses. This process utilizes a temporary substrate consisting of a water-soluble polymer film as a base for the electron-beam deposition of the metal layer. After formation of the metal foil, the polymer is removed by immersion of the assembly in water. Unbacked metal-foil cylinders as thin as 0.17 ..mu..m with extremely smooth, wrinkle-free surfaces have been produced by this technique. Polyvinyl alcohol was an excellent substrate. Aluminum foils were produced.

  3. 40 CFR 435.60 - Applicability; description of the stripper subcategory.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... of crude oil and which are operating at the maximum feasible rate of production and in accordance... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS OIL AND GAS EXTRACTION POINT SOURCE CATEGORY Stripper... in the oil and gas extraction industry....

  4. 40 CFR 435.60 - Applicability; description of the stripper subcategory.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS OIL AND GAS EXTRACTION POINT SOURCE CATEGORY Stripper... in the oil and gas extraction industry. ... of crude oil and which are operating at the maximum feasible rate of production and in...

  5. SELECTION AND TREATMENT OF STRIPPER GAS WELLS FOR PRODUCTION ENHANCEMENT IN THE MID-CONTINENT

    SciTech Connect

    Scott Reeves

    2003-03-01

    Stripper gas wells are an important source of domestic energy supply and under constant threat of permanent loss (shut-in) due to marginal economics. In 1998, 192 thousand stripper gas wells produced over a Tcf of gas, at an average rate of less than 16 Mcfd. This represents about 57% of all producing gas wells in the onshore lower-48 states, yet only 8% of production. Reserves of stripper gas wells are estimated to be only 1.6 Tcf, or slightly over 1% of the onshore lower-48 total (end of year 1996 data). Obviously, stripper gas wells are at the very margin of economic sustenance. As the demand for natural gas in the U.S. grows to the forecasted estimate of over 30 Tcf annually by the year 2010, supply from current conventional sources is expected to decline. Therefore, an important need exists to fully exploit known domestic resources of natural gas, including those represented by stripper gas wells. The overall objectives of this project are to develop an efficient and low-cost methodology to broadly categorize the well performance characteristics for a stripper gas field, identify the high-potential candidate wells for remediation, and diagnose the specific causes for well underperformance. With this capability, stripper gas well operators can more efficiently and economically produce these resources and maximize these gas reserves. A further objective is to identify/develop, evaluate and test ''new and novel,'' economically viable remediation options. Finally, it is the objective of this project that all the methods and technologies developed in this project, while being tested in the Mid-Continent, be widely applicable to stripper gas wells of all types across the country. The project activities during the reporting period were: (1) The contract was signed on August 20, 2000. Little work has been performed other than preliminary planning to get the project underway.

  6. SELECTION AND TREATMENT OF STRIPPER GAS WELLS FOR PRODUCTION ENHANCEMENT IN THE MID-CONTINENT

    SciTech Connect

    Scott Reeves

    2003-04-01

    Stripper gas wells are an important source of domestic energy supply and under constant threat of permanent loss (shut-in) due to marginal economics. In 1998, 192 thousand stripper gas wells produced over a Tcf of gas, at an average rate of less than 16 Mcfd. This represents about 57% of all producing gas wells in the onshore lower-48 states, yet only 8% of production. Reserves of stripper gas wells are estimated to be only 1.6 Tcf, or slightly over 1% of the onshore lower-48 total (end of year 1996 data). Obviously, stripper gas wells are at the very margin of economic sustenance. As the demand for natural gas in the U.S. grows to the forecasted estimate of over 30 Tcf annually by the year 2010, supply from current conventional sources is expected to decline. Therefore, an important need exists to fully exploit known domestic resources of natural gas, including those represented by stripper gas wells. The overall objectives of this project are to develop an efficient and low-cost methodology to broadly categorize the well performance characteristics for a stripper gas field, identify the high-potential candidate wells for remediation, and diagnose the specific causes for well underperformance. With this capability, stripper gas well operators can more efficiently and economically produce these resources and maximize these gas reserves. A further objective is to identify/develop, evaluate and test ''new and novel,'' economically viable remediation options. Finally, it is the objective of this project that all the methods and technologies developed in this project, while being tested in the Mid-Continent, be widely applicable to stripper gas wells of all types across the country. The project activities during the reporting period were: Continued coordinating the final selection of candidates and field implementation with Oneok. Oneok plans on performing the operations early in 2003.

  7. SELECTION AND TREATMENT OF STRIPPER GAS WELLS FOR PRODUCTION ENHANCEMENT IN THE MID-CONTINENT

    SciTech Connect

    Scott Reeves

    2003-03-01

    Stripper gas wells are an important source of domestic energy supply and under constant threat of permanent loss (shut-in) due to marginal economics. In 1998, 192 thousand stripper gas wells produced over a Tcf of gas, at an average rate of less than 16 Mcfd. This represents about 57% of all producing gas wells in the onshore lower-48 states, yet only 8% of production. Reserves of stripper gas wells are estimated to be only 1.6 Tcf, or slightly over 1% of the onshore lower-48 total (end of year 1996 data). Obviously, stripper gas wells are at the very margin of economic sustenance. As the demand for natural gas in the U.S. grows to the forecasted estimate of over 30 Tcf annually by the year 2010, supply from current conventional sources is expected to decline. Therefore, an important need exists to fully exploit known domestic resources of natural gas, including those represented by stripper gas wells. The overall objectives of this project are to develop an efficient and low-cost methodology to broadly categorize the well performance characteristics for a stripper gas field, identify the high-potential candidate wells for remediation, and diagnose the specific causes for well underperformance. With this capability, stripper gas well operators can more efficiently and economically produce these resources and maximize these gas reserves. A further objective is to identify/develop, evaluate and test ''new and novel,'' economically viable remediation options. Finally, it is the objective of this project that all the methods and technologies developed in this project, while being tested in the Mid-Continent, be widely applicable to stripper gas wells of all types across the country. The project activities during the reporting period were: (1) Continued coordinating the final selection of candidates and field implementation with Oneok. Oneok plans on performing the operations early in 2003.

  8. SELECTION AND TREATMENT OF STRIPPER GAS WELLS FOR PRODUCTION ENHANCEMENT IN THE MID-CONTINENT

    SciTech Connect

    Scott Reeves

    2003-03-01

    Stripper gas wells are an important source of domestic energy supply and under constant threat of permanent loss (shut-in) due to marginal economics. In 1998, 192 thousand stripper gas wells produced over a Tcf of gas, at an average rate of less than 16 Mcfd. This represents about 57% of all producing gas wells in the onshore lower-48 states, yet only 8% of production. Reserves of stripper gas wells are estimated to be only 1.6 Tcf, or slightly over 1% of the onshore lower-48 total (end of year 1996 data). Obviously, stripper gas wells are at the very margin of economic sustenance. As the demand for natural gas in the U.S. grows to the forecasted estimate of over 30 Tcf annually by the year 2010, supply from current conventional sources is expected to decline. Therefore, an important need exists to fully exploit known domestic resources of natural gas, including those represented by stripper gas wells. The overall objectives of this project are to develop an efficient and low-cost methodology to broadly categorize the well performance characteristics for a stripper gas field, identify the high-potential candidate wells for remediation, and diagnose the specific causes for well underperformance. With this capability, stripper gas well operators can more efficiently and economically produce these resources and maximize these gas reserves. A further objective is to identify/develop, evaluate and test ''new and novel,'' economically viable remediation options. Finally, it is the objective of this project that all the methods and technologies developed in this project, while being tested in the Mid-Continent, be widely applicable to stripper gas wells of all types across the country. The project activities during the reporting period were: (1) Began preparing final project report, less the field implementation component. (2) Coordinated the final selection of candidates and field implementation with Oneok.

  9. Rhenium-Foil Witness Cylinders

    NASA Technical Reports Server (NTRS)

    Knight, B. L.

    1992-01-01

    Cylindrical portion of wall of combustion chamber replaced with rhenium foil mounted on holder. Rhenium oxidizes without melting, indicating regions of excess oxidizer in combustion-chamber flow. Rhenium witness foils also useful in detecting excess oxygen and other oxidizers at temperatures between 2,000 and 3,600 degrees F in burner cores of advanced gas-turbine engines.

  10. Consequences of FOIL for Undergraduates

    ERIC Educational Resources Information Center

    Koban, Lori; Sisneros-Thiry, Simone

    2015-01-01

    FOIL is a well-known mnemonic that is used to find the product of two binomials. We conduct a large sample (n = 252) observational study of first-year college students and show that while the FOIL procedure leads to the accurate expansion of the product of two binomials for most students who apply it, only half of these students exhibit conceptual…

  11. Alternative stripper configurations for CO{sub 2} capture by aqueous amines

    SciTech Connect

    Oyenekan, B.A.; Rochelle, G.T.

    2007-12-15

    Aqueous absorption/stripping is a promising technology for the capture of CO{sub 2} from existing or new coal-fired power plants. Four new stripper configurations (matrix, internal exchange, flashing feed, and multipressure with split feed) have been evaluated with seven model solvents that approximate the thermodynamic and rate properties of 7m (30 wt %) monoethanolamine (MEA), potassium carbonate promoted bypiperazine (PZ), promoted MEA, methyldiethanolamine (MDEA) promoted by PZ, and hindered amines. The results show that solvents with high heats of absorption (MEA, MEA/PZ) favor operation at normal pressure. The relative performance of the alternative configurations is matrix > internal exchange > multipressure with split feed > flashing feed. MEA/PZ and MDEA/PZ are attractive alternatives to 7m MEA. The best solvent and process configuration, matrix with MDEA/PZ, offers 22 and 15% energy savings over the baseline and improved baseline, respectively,with stripping and compression to 10 MPa. The energy requirement for stripping and compression to 10 MPa is about 20% of the power output from a 500 MW power plant with 90% CO{sub 2} removal.

  12. Consequences of FOIL for undergraduates

    NASA Astrophysics Data System (ADS)

    Koban, Lori; Sisneros-Thiry, Simone

    2015-02-01

    FOIL is a well-known mnemonic that is used to find the product of two binomials. We conduct a large sample (n = 252) observational study of first-year college students and show that while the FOIL procedure leads to the accurate expansion of the product of two binomials for most students who apply it, only half of these students exhibit conceptual understanding of the procedure. We generalize this FOIL dichotomy and show that the ability to transfer a mathematical property from one context to a less familiar context is related to both procedural success and attitude towards math.

  13. Induction Bonding of Prepreg Tape and Titanium Foil

    NASA Technical Reports Server (NTRS)

    Messier, Bernadette C.; Hinkley, Jeffrey A.; Johnston, Norman J.

    1998-01-01

    Hybrid structural laminates made of titanium foil and carbon fiber reinforced polymer composite offer a potential for improved performance in aircraft structural applications. To obtain information needed for the automated fabrication of hybrid laminates, a series of bench scale tests were conducted of the magnetic induction bonding of titanium foil and thermoplastic prepreg tape. Foil and prepreg specimens were placed in the gap of a toroid magnet mounted in a bench press. Several magnet power supplies were used to study power at levels from 0.5 to 1.75 kW and frequencies from 50 to 120 kHz. Sol-gel surface-treated titanium foil, 0.0125 cm thick, and PIXA/IM7 prepreg tape were used in several lay-up configurations. Data were obtained on wedge peel bond strength, heating rate, and temperature ramp over a range of magnet power levels and frequencies at different "power-on" times for several magnet gap dimensions. These data will be utilized in assessing the potential for automated processing. Peel strengths of foil-tape bonds depended on the maximum temperature reached during heating and on the applied pressure. Maximum peel strengths were achieved at 1.25kW and 8OkHz. Induction heating of the foil appears to be capable of good bonding up to 10 plies of tape. Heat transfer calculations indicate that a 20-40 C temperature difference exists across the tape thickness during heat-up.

  14. Laser surface texturization for high power cladding light stripper

    NASA Astrophysics Data System (ADS)

    Berisset, Michael; Lebrun, Léo.; Faucon, Marc; Kling, Rainer; Boullet, Johan; Aguergaray, Claude

    2016-03-01

    We demonstrated herein a new type of cladding light strippers suitable for high power systems. By precisely micro-machining the surface of the fiber we create CLS with efficiencies as high as 97 % for large NA, multi-mode, cladding light (NA = 0.3), and 70 % for single-mode, low NA, light. The NA of the cladding light is reduced from 0.3 down to 0.08. The CLS exhibit a 1°C/stripped-Watt temperature elevation making them very suitable for high power applications. This fabrication method is simple and reliable. We have tested different texturization geometries on several different fibers: 20/400 from Nufern, KAGOME, and LMA 10 and LMA 15 fibers (results not shown herein) and we observed good efficiencies and temperature elevation behavior for all of them. Finally, large scale production of CLS with this method is possible since the time necessary to prepare on CLS is very small, in the order of few seconds.

  15. SELECTION AND TREATMENT OF STRIPPER GAS WELLS FOR PRODUCTION ENHANCEMENT IN THE MID-CONTINENT

    SciTech Connect

    Scott Reeves

    2003-03-01

    Stripper gas wells are an important source of domestic energy supply and under constant threat of permanent loss (shut-in) due to marginal economics. In 1998, 192 thousand stripper gas wells produced over a Tcf of gas, at an average rate of less than 16 Mcfd. This represents about 57% of all producing gas wells in the onshore lower-48 states, yet only 8% of production. Reserves of stripper gas wells are estimated to be only 1.6 Tcf, or slightly over 1% of the onshore lower-48 total (end of year 1996 data). Obviously, stripper gas wells are at the very margin of economic sustenance. As the demand for natural gas in the U.S. grows to the forecasted estimate of over 30 Tcf annually by the year 2010, supply from current conventional sources is expected to decline. Therefore, an important need exists to fully exploit known domestic resources of natural gas, including those represented by stripper gas wells. The overall objectives of this project are to develop an efficient and low-cost methodology to broadly categorize the well performance characteristics for a stripper gas field, identify the high-potential candidate wells for remediation, and diagnose the specific causes for well underperformance. With this capability, stripper gas well operators can more efficiently and economically produce these resources and maximize these gas reserves. A further objective is to identify/develop, evaluate and test ''new and novel,'' economically viable remediation options. Finally, it is the objective of this project that all the methods and technologies developed in this project, while being tested in the Mid-Continent, be widely applicable to stripper gas wells of all types across the country. The project activities during the reporting period were: (1) Type curve matching continued during the reporting period. (2) A second data collection trip to Tulsa was performed to gather information on the additional reservoirs to be included in the analysis. Created updated database

  16. SELECTION AND TREATMENT OF STRIPPER GAS WELLS FOR PRODUCTION ENHANCEMENT IN THE MID-CONTINENT

    SciTech Connect

    Scott Reeves

    2003-03-01

    Stripper gas wells are an important source of domestic energy supply and under constant threat of permanent loss (shut-in) due to marginal economics. In 1998, 192 thousand stripper gas wells produced over a Tcf of gas, at an average rate of less than 16 Mcfd. This represents about 57% of all producing gas wells in the onshore lower-48 states, yet only 8% of production. Reserves of stripper gas wells are estimated to be only 1.6 Tcf, or slightly over 1% of the onshore lower-48 total (end of year 1996 data). Obviously, stripper gas wells are at the very margin of economic sustenance. As the demand for natural gas in the U.S. grows to the forecasted estimate of over 30 Tcf annually by the year 2010, supply from current conventional sources is expected to decline. Therefore, an important need exists to fully exploit known domestic resources of natural gas, including those represented by stripper gas wells. The overall objectives of this project are to develop an efficient and low-cost methodology to broadly categorize the well performance characteristics for a stripper gas field, identify the high-potential candidate wells for remediation, and diagnose the specific causes for well underperformance. With this capability, stripper gas well operators can more efficiently and economically produce these resources and maximize these gas reserves. A further objective is to identify/develop, evaluate and test ''new and novel,'' economically viable remediation options. Finally, it is the objective of this project that all the methods and technologies developed in this project, while being tested in the Mid-Continent, be widely applicable to stripper gas wells of all types across the country. The project activities during the reporting period were: (1) The search for another field site was abandoned after discussion with DOE. There is a clear absence of willing industry partners to participate in this project. The greatest obstacle is having the necessary data to perform the

  17. SELECTION AND TREATMENT OF STRIPPER GAS WELLS FOR PRODUCTION ENHANCEMENT IN THE MID-CONTINENT

    SciTech Connect

    Scott Reeves

    2003-08-01

    Stripper gas wells are an important source of domestic energy supply and under constant threat of permanent loss (shut-in) due to marginal economics. In 1998, 192 thousand stripper gas wells produced over a Tcf of gas, at an average rate of less than 16 Mcfd. This represents about 57% of all producing gas wells in the onshore lower-48 states, yet only 8% of production. Reserves of stripper gas wells are estimated to be only 1.6 Tcf, or slightly over 1% of the onshore lower-48 total (end of year 1996 data). Obviously, stripper gas wells are at the very margin of economic sustenance. As the demand for natural gas in the U.S. grows to the forecasted estimate of over 30 Tcf annually by the year 2010, supply from current conventional sources is expected to decline. Therefore, an important need exists to fully exploit known domestic resources of natural gas, including those represented by stripper gas wells. The overall objectives of this project are to develop an efficient and low-cost methodology to broadly categorize the well performance characteristics for a stripper gas field, identify the high-potential candidate wells for remediation, and diagnose the specific causes for well underperformance. With this capability, stripper gas well operators can more efficiently and economically produce these resources and maximize these gas reserves. A further objective is to identify/develop, evaluate and test ''new and novel,'' economically viable remediation options. Finally, it is the objective of this project that all the methods and technologies developed in this project, while being tested in the Mid-Continent, be widely applicable to stripper gas wells of all types across the country. The project activities during the reporting period were: (1) Compiled information and results of field activities that Oneok has conducted in relation to the project. Field activities have included performing six pressure transient tests, and implementing six workovers, four of which were

  18. SELECTION AND TREATMENT OF STRIPPER GAS WELLS FOR PRODUCTION ENHANCEMENT IN THE MID-CONTINENT

    SciTech Connect

    Scott Reeves

    2003-03-01

    Stripper gas wells are an important source of domestic energy supply and under constant threat of permanent loss (shut-in) due to marginal economics. In 1998, 192 thousand stripper gas wells produced over a Tcf of gas, at an average rate of less than 16 Mcfd. This represents about 57% of all producing gas wells in the onshore lower-48 states, yet only 8% of production. Reserves of stripper gas wells are estimated to be only 1.6 Tcf, or slightly over 1% of the onshore lower-48 total (end of year 1996 data). Obviously, stripper gas wells are at the very margin of economic sustenance. As the demand for natural gas in the U.S. grows to the forecasted estimate of over 30 Tcf annually by the year 2010, supply from current conventional sources is expected to decline. Therefore, an important need exists to fully exploit known domestic resources of natural gas, including those represented by stripper gas wells. The overall objectives of this project are to develop an efficient and low-cost methodology to broadly categorize the well performance characteristics for a stripper gas field, identify the high-potential candidate wells for remediation, and diagnose the specific causes for well underperformance. With this capability, stripper gas well operators can more efficiently and economically produce these resources and maximize these gas reserves. A further objective is to identify/develop, evaluate and test ''new and novel,'' economically viable remediation options. Finally, it is the objective of this project that all the methods and technologies developed in this project, while being tested in the Mid-Continent, be widely applicable to stripper gas wells of all types across the country. The project activities during the reporting period were: (1) Finished preparing the final project report, less the field implementation component. Sent to DOE for review. (2) Continued coordinating the final selection of candidates and field implementation with Oneok. Oneok postponed field

  19. SELECTION AND TREATMENT OF STRIPPER GAS WELLS FOR PRODUCTION ENHANCEMENT IN THE MID-CONTINENT

    SciTech Connect

    Scott Reeves

    2003-03-01

    Stripper gas wells are an important source of domestic energy supply and under constant threat of permanent loss (shut-in) due to marginal economics. In 1998, 192 thousand stripper gas wells produced over a Tcf of gas, at an average rate of less than 16 Mcfd. This represents about 57% of all producing gas wells in the onshore lower-48 states, yet only 8% of production. Reserves of stripper gas wells are estimated to be only 1.6 Tcf, or slightly over 1% of the onshore lower-48 total (end of year 1996 data). Obviously, stripper gas wells are at the very margin of economic sustenance. As the demand for natural gas in the U.S. grows to the forecasted estimate of over 30 Tcf annually by the year 2010, supply from current conventional sources is expected to decline. Therefore, an important need exists to fully exploit known domestic resources of natural gas, including those represented by stripper gas wells. The overall objectives of this project are to develop an efficient and low-cost methodology to broadly categorize the well performance characteristics for a stripper gas field, identify the high-potential candidate wells for remediation, and diagnose the specific causes for well underperformance. With this capability, stripper gas well operators can more efficiently and economically produce these resources and maximize these gas reserves. A further objective is to identify/develop, evaluate and test ''new and novel,'' economically viable remediation options. Finally, it is the objective of this project that all the methods and technologies developed in this project, while being tested in the Mid-Continent, be widely applicable to stripper gas wells of all types across the country. The project activities during the reporting period were: (1) Continued to solicit industry research partners to provide test sites, including Patina Oil and Gas and EOG Resources, each of whom have previously worked with ARI on a similar projects funded by the Gas Technology Institute. Both

  20. SELECTION AND TREATMENT OF STRIPPER GAS WELLS FOR PRODUCTION ENHANCEMENT IN THE MID-CONTINENT

    SciTech Connect

    Scott Reeves

    2003-03-01

    Stripper gas wells are an important source of domestic energy supply and under constant threat of permanent loss (shut-in) due to marginal economics. In 1998, 192 thousand stripper gas wells produced over a Tcf of gas, at an average rate of less than 16 Mcfd. This represents about 57% of all producing gas wells in the onshore lower-48 states, yet only 8% of production. Reserves of stripper gas wells are estimated to be only 1.6 Tcf, or slightly over 1% of the onshore lower-48 total (end of year 1996 data). Obviously, stripper gas wells are at the very margin of economic sustenance. As the demand for natural gas in the U.S. grows to the forecasted estimate of over 30 Tcf annually by the year 2010, supply from current conventional sources is expected to decline. Therefore, an important need exists to fully exploit known domestic resources of natural gas, including those represented by stripper gas wells. The overall objectives of this project are to develop an efficient and low-cost methodology to broadly categorize the well performance characteristics for a stripper gas field, identify the high-potential candidate wells for remediation, and diagnose the specific causes for well underperformance. With this capability, stripper gas well operators can more efficiently and economically produce these resources and maximize these gas reserves. A further objective is to identify/develop, evaluate and test ''new and novel,'' economically viable remediation options. Finally, it is the objective of this project that all the methods and technologies developed in this project, while being tested in the Mid-Continent, be widely applicable to stripper gas wells of all types across the country. The project activities during the reporting period were: (1) Completed both type curve and artificial neural network analysis of the field. Developed list of production enhancement candidates. (2) Made final presentation of results to Oneok in Tulsa (February 26). (3) Made presentations on

  1. Method for fabricating uranium foils and uranium alloy foils

    DOEpatents

    Hofman, Gerard L.; Meyer, Mitchell K.; Knighton, Gaven C.; Clark, Curtis R.

    2006-09-05

    A method of producing thin foils of uranium or an alloy. The uranium or alloy is cast as a plate or sheet having a thickness less than about 5 mm and thereafter cold rolled in one or more passes at substantially ambient temperatures until the uranium or alloy thereof is in the shape of a foil having a thickness less than about 1.0 mm. The uranium alloy includes one or more of Zr, Nb, Mo, Cr, Fe, Si, Ni, Cu or Al.

  2. Lithium-6 foil neutron detector

    SciTech Connect

    Young, C.A.

    1982-12-21

    A neutron detection apparatus is provided which includes a selected number of flat surfaces of lithium-6 foil, and which further includes a gas mixture in contact with each of the flat surfaces for selectively reacting to charged particles emitted by or radiated from the lithium foil. A container is provided to seal the lithium foil and the gas mixture in a volume from which water vapor and atmospheric gases are excluded, the container having one or more walls which are transmissive to neutrons. Monitoring equipment in contact with the gas mixture detects reactions taking place in the gas mixture, and, in response to such reactions, provides notice of the flux of neutrons passing through the volume of the detector.

  3. SELECTIVE ABSORBER COATED FOILS FOR SOLAR COLLECTORS

    SciTech Connect

    Lampert, Carl M.

    1980-04-01

    Solar absorber metal foils are discussed in terms of materials and basic processing science. Also included is the use of finished heavy sheet stock for direct fabrication of solar collector panels. Both the adhesives and bonding methods for foils and sheet are surveyed. Developmental and representative commercial foils are used as illustrative examples. As a result it was found that foils can compete economically with batch plating but are limited by adhesive temperature stability. Also absorber foils are very versatile and direct collector fabrication from heavy foils appears very promising.

  4. Foil dissociation of fast molecular ions into atomic excited states

    SciTech Connect

    Berry, H.G.; Gay, T.J.; Brooks, R.L.

    1980-01-01

    The intensity and polarizations of light emitted from atomic excited states of dissociated molecular ions were measured. The dissociations are induced when fast molecular ions (50 to 500 keV/amu) are transmitted through thin carbon foils. A calculation of multiple scattering and the Coulomb explosion gives the average internuclear separation of the projectile at the foil surface. Experimentally, the foil thickness is varied to give varying internuclear separations at the foil surface and observe the consequent variation in light yield and optical polarization. Using HeH/sup +/ projectiles, factors of 1 to 5 enhancements of the light yields from n = 3, /sup 1/ /sup 3/P,D states of He I and some He II and H I emissions were observed. The results can be explained in terms of molecular level crossings which provide mixings of the various final states during dissociation of the molecular ions at the exit surface. They suggest a short range surface interaction of the electron pick-up followed by a slow molecular dissociation. Alignment measurements confirm the essential features of the model. Observations of Lyman ..cap alpha.. emission after dissociation of H/sub 2//sup +/ amd H/sub 3//sup +/ show rapid variations in light yield for small internuclear separations at the foil surface.

  5. NONPROCESS SOLVENT USE IN THE FURNITURE REFINISHING AND REPAIR INDUSTRY: EVALUATION OF ALTERNATIVE STRIPPERS

    EPA Science Inventory

    The report gives results of an evaluation of the feasibility of using alternatives to high volatile organic compound/hazardous air pollutant (VOC/HAP) solvent-based, chemical strippers that are currently used in the furniture repair and refinishing industry to remove both traditi...

  6. LOW COST METHODOLOGIES TO ANALYZE AND CORRECT ABNORMAL PRODUCTION DECLINE IN STRIPPER GAS WELLS

    SciTech Connect

    Jerry James; Gene Huck; Tim Knobloch

    2000-10-01

    The goal of this research program is to develop and deliver a procedure guide of low cost methodologies to analyze and correct problems with stripper wells experiencing abnormal production declines. A study group of wells will provide data to determine the historic frequency of the problem of abnormal production declines in stripper gas wells and the historic frequency of the causes of the production problems. Once the most frequently occurring causes of the production problems are determined, data collection forms and decision trees will be designed to cost-effectively diagnose these problems and suggest corrective action. Finally, economic techniques to solve the most frequently occurring problems will be researched and implemented. These systematic methodologies and techniques will increase the efficiency of problem assessment and implementation of solutions for stripper gas wells. According to the original proposal, this fourth quarterly technical report was to deliver a procedure guide, a summary report, and a Society of Petroleum Engineers technical paper. However, James Engineering, Inc. was granted a six month, no cost extension to allow the required time to thoroughly investigate and prepare these portions of the study, therefore completion of the current deliverables has been re-scheduled. James Engineering, Inc. did present preliminary results of the study during a panel discussion on Stripper Gas Wells at the Society of Petroleum Engineers' Eastern Regional Meeting held in Morgantown, West Virginia October 19, 2000. No cost to the study was incurred for the preliminary presentation.

  7. Yields in stripper header vs conventional header in dryland cropping systems

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Differences in crop residue quality can impact the amount of soil water storage in semi-arid no-till systems of the West Central Great Plains. Using a stripper header as opposed to a conventional-reel type header to harvest small grains impacts the quality of the crop residue left in the field. Pr...

  8. Proso Millet Yield and Residue Mass Following Direct Harvest with a Stripper-header

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Proso millet (Panicum miliaceum L.) (PM) is an important crop for dryland agricultural rotations in the central Great Plains. The crop is traditionally swathed prior to combining to promote uniform drying of the panicle and to minimize seed shattering losses. Direct harvesting of PM with a stripper ...

  9. Development of a high-capacity extractor cleaner for cotton strippers

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Cotton strippers have used extractor type cleaners for many years to remove large foreign material from harvested seed cotton. These machines are commonly referred to as "field cleaners" and are similar in design and operation to stick machines used in gins. The field cleaners used on modern cotton ...

  10. Picker vs. stripper harvesting in the Texas High Plains: Agronomic implications

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Many changes have occurred during the last decade in the Texas High Plains which have resulted in increased cotton yields and improved fiber quality. The main factors associated with both higher lint yield and quality include a shift in varieties planted, with virtually no "storm-proof stripper type...

  11. 30 CFR 1210.155 - What reports must I submit for Federal onshore stripper oil properties?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... rate by the Bureau of Land Management (BLM) under 43 CFR 3103.4-2 must submit Form MMS-4377, Stripper Royalty Rate Reduction Notification, under 43 CFR 3103.4-2(b)(3). (b) Reporting options. You may find Form... mail addressed to Office of Natural Resources Revenue (ONRR), P.O. Box 25165, MS 392B2,...

  12. NONPROCESS SOLVENT USE IN THE FURNITURE REFINISHING AND REPAIR INDUSTRY: EVALUATION OF ALTERNATIVE CHEMICAL STRIPPERS

    EPA Science Inventory

    The report gives results of an evaluation of the feasibility of using alternatives to high volatile organic compound/hazardous air pollutant (VOC/HAP) solvent-based, chemical strippers that are currently used in the furniture repair and refinishing industry to remove both traditi...

  13. Force Generation by Flapping Foils

    NASA Astrophysics Data System (ADS)

    Bandyopadhyay, P. R.; Donnelly, M.

    1996-11-01

    Aquatic animals like fish use flapping caudal fins to produce axial and cross-stream forces. During WW2, German scientists had built and tested an underwater vehicle powered by similar flapping foils. We have examined the forces produced by a pair of flapping foils. We have examined the forced produced by a pair of flapping foils attached to the tail end of a small axisymmetric cylinder. The foils operate in-phase (called waving), or in anti-phase (called clapping). In a low-speed water tunnel, we have undertaken time-dependent measurements of axial and cross-stream forces and moments that are exerted by the vortex shedding process over the entire body. Phase-matched LDV measurements of vorticity-velocity vectors, as well as limited flow visualization of the periodic vortex shedding process have also been carried out. The direction of the induced velocity within a pair of shed vortices determines the nature of the forces produced, viz., thrust or drag or cross-stream forces. The clapping mode produces a widely dispersed symmetric array of vortices which results in axial forces only (thrust and rag). On the other hand, the vortex array is staggered in the waving mode and cross-stream (maneuvering) forces are then generated.

  14. Safety evaluation of the ITP filter/stripper test runs and quiet time runs using simulant solution. Revision 3

    SciTech Connect

    Gupta, M.K.

    1994-06-01

    The purpose is to provide the technical bases for the evaluation of Unreviewed Safety Question for the In-Tank Precipitation (ITP) Filter/Stripper Test Runs (Ref. 7) and Quiet Time Runs Program (described in Section 3.6). The Filter/Stripper Test Runs and Quiet Time Runs program involves a 12,000 gallon feed tank containing an agitator, a 4,000 gallon flush tank, a variable speed pump, associated piping and controls, and equipment within both the Filter and the Stripper Building.

  15. Agglomeration in Stripper Ash Coolers and Its Possible Remedial Solutions: a Case Study

    NASA Astrophysics Data System (ADS)

    Singh, Ravi Inder

    2016-04-01

    The bottom ash of circulating fluidized bed (CFB) boiler contains large amounts of physical heat. When low quality coals are used in these types of boilers, the ash content is normally more than 40 % and the physical heat loss is approximately 3 % if the bottom ash is discharged without cooling. Bottom ash cooler (BAC) is often used to treat the high temperature bottom ash to reclaim heat, and to facilitate the easily handling and transportation of ash. The CFB boiler at BLA Power, Newari, MP (India) is facing problems of clinker formation in strip ash coolers of plant since the installation of unit. These clinkers are basically agglomerates, which leads to defluidization of stripper ash cooler (BAC) units. There are two strip ash coolers in unit. Each strip ash cooler is capable of working independently. The proper functioning of both strip coolers is very important as it is going to increase the combustion efficiency of boiler by stripping of fine unburnt coal particles from ash, which are injected into the furnace. In this paper causes, characterization of agglomerates, thermo gravimetric analysis of fuel used, particular size distribution of coal and sand and possible remedial solution to overcome these agglomerates in strip ash coolers has also been presented. High temperature in compact separators, non uniform supply of coal and not removing small agglomerates from stripper ash cooler are among main causes of agglomeration in stripper ash cooler. Control of compact separator temperature, replacing 10-12 % of bed material and cleaning stripper ash cooler periodically will decrease agglomeration in stripper ash cooler of unit.

  16. Passive Thermal Management of Foil Bearings

    NASA Technical Reports Server (NTRS)

    Bruckner, Robert J. (Inventor)

    2015-01-01

    Systems and methods for passive thermal management of foil bearing systems are disclosed herein. The flow of the hydrodynamic film across the surface of bearing compliant foils may be disrupted to provide passive cooling and to improve the performance and reliability of the foil bearing system.

  17. Extended foil capacitor with radially spoked electrodes

    DOEpatents

    Foster, James C.

    1990-01-01

    An extended foil capacitor has a conductive disk electrically connected in oncrushing contact to the extended foil. A conductive paste is placed through spaces between radial spokes on the disk to electrically and mechanically connect the extended foil to the disk.

  18. Novel single stripper with side-draw to remove ammonia and sour gas simultaneously for coal-gasification wastewater treatment and the industrial implementation

    SciTech Connect

    Feng, D.C.; Yu, Z.J.; Chen, Y.; Qian, Y.

    2009-06-15

    A large amount of wastewater is produced in the Lurgi coal-gasification process with the complex compounds carbon dioxide, ammonia, phenol, etc., which cause a serious environmental problem. In this paper, a novel stripper operated at elevated pressure is designed to improve the pretreatment process. In this technology, two noticeable improvements were established. First, the carbon dioxide and ammonia were removed simultaneously in a single stripper where sour gas (mainly carbon dioxide) is removed from the tower top and the ammonia vapor is drawn from the side and recovered by partial condensation. Second, the ammonia is removed before the phenol recovery to reduce the pH value of the subsequent extraction units, so as the phenol removal performance of the extraction is greatly improved. To ensure the operational efficiency, some key operational parameters are analyzed and optimized though simulation. It is shown that when the top temperature is kept at 40 C and the weight ratio of the side draw to the feed is above 9%, the elevated pressures can ensure the removal efficiency of NH{sub 3} and carbon dioxide and the desired purified water as the bottom product of the unit is obtained. A real industrial application demonstrates the attractiveness of the new technique: it removes 99.9% CO{sub 2} and 99.6% ammonia, compared to known techniques which remove 66.5% and 94.4%, respectively. As a result, the pH value of the wastewater is reduced from above 9 to below 7. This ensures that the phenol removal ratio is above 93% in the following extraction units. The operating cost is lower than that of known techniques, and the operation is simplified.

  19. Development of nanodiamond foils for H- stripping to Support the Spallation Neutron Source (SNS) using hot filament chemical vapor deposition

    SciTech Connect

    Vispute, R D; Ermer, Henry K; Sinsky, Phillip; Seiser, Andrew; Shaw, Robert W; Wilson, Leslie L

    2014-01-01

    Thin diamond foils are needed in many particle accelerator experiments regarding nuclear and atomic physics, as well as in some interdisciplinary research. Particularly, nanodiamond texture is attractive for this purpose as it possesses a unique combination of diamond properties such as high thermal conductivity, mechanical strength and high radiation hardness; therefore, it is a potential material for energetic ion beam stripper foils. At the ORNL Spallation Neutron Source (SNS), the installed set of foils must be able to survive a nominal five-month operation period, without the need for unscheduled costly shutdowns and repairs. Thus, a small foil about the size of a postage stamp is critical to the operation of SNS and similar sources in U.S. laboratories and around the world. We are investigating nanocrystalline, polycrystalline and their admixture films fabricated using a hot filament chemical vapor deposition (HFCVD) system for H- stripping to support the SNS at Oak Ridge National Laboratory. Here we discuss optimization of process variables such as substrate temperature, process gas ratio of H2/Ar/CH4, substrate to filament distance, filament temperature, carburization conditions, and filament geometry to achieve high purity diamond foils on patterned silicon substrates with manageable intrinsic and thermal stresses so that they can be released as free standing foils without curling. An in situ laser reflectance interferometry tool (LRI) is used for monitoring the growth characteristics of the diamond thin film materials. The optimization process has yielded free standing foils with no pinholes. The sp3/sp2 bonds are controlled to optimize electrical resistivity to reduce the possibility of surface charging of the foils. The integrated LRI and HFCVD process provides real time information on the growth of films and can quickly illustrate growth features and control film thickness. The results are discussed in the light of development of nanodiamond foils that

  20. Development of thin foils for use in generating neutral particle beams

    SciTech Connect

    Aaron, W.S.; Zevenbergen, L.A.; Adair, H.L.; Culpepper, C.A.; McCulla, W.H.; Nolan, T.A.; Hughes, M.R.

    1986-01-01

    The Isotope Research Materials Laboratory (IRML) was requested to prepare large-area, ultrathin aluminum and carbon foils for use in beam neutralization experiments. There were two major parts to this request. The first was to immediately provide a number of 5-cm-dia foils 5 to 20 ..mu..g/cm/sup 2/ thick for use in experiments at the Fusion Materials Irradiation Test (FMIT) facility and at Argonne National Laboratory (ANL). The second, longer-term request was to develop methods to prepare 25-cm x 25-cm, 10-..mu..g/cm/sup 2/ aluminum neutralizer foils. Both parts of the request have been successfully met.

  1. SELECTION AND TREATMENT OF STRIPPER GAS WELLS FOR PRODUCTION ENHANCEMENT IN THE MID-CONTINENT

    SciTech Connect

    Scott Reeves

    2003-03-01

    Stripper gas wells are an important source of domestic energy supply and under constant threat of permanent loss (shut-in) due to marginal economics. In 1998, 192 thousand stripper gas wells produced over a Tcf of gas, at an average rate of less than 16 Mcfd. This represents about 57% of all producing gas wells in the onshore lower-48 states, yet only 8% of production. Reserves of stripper gas wells are estimated to be only 1.6 Tcf, or slightly over 1% of the onshore lower-48 total (end of year 1996 data). Obviously, stripper gas wells are at the very margin of economic sustenance. As the demand for natural gas in the U.S. grows to the forecasted estimate of over 30 Tcf annually by the year 2010, supply from current conventional sources is expected to decline. Therefore, an important need exists to fully exploit known domestic resources of natural gas, including those represented by stripper gas wells. The overall objectives of this project are to develop an efficient and low-cost methodology to broadly categorize the well performance characteristics for a stripper gas field, identify the high-potential candidate wells for remediation, and diagnose the specific causes for well underperformance. With this capability, stripper gas well operators can more efficiently and economically produce these resources and maximize these gas reserves. A further objective is to identify/develop, evaluate and test ''new and novel,'' economically viable remediation options. Finally, it is the objective of this project that all the methods and technologies developed in this project, while being tested in the Mid-Continent, be widely applicable to stripper gas wells of all types across the country. The project activities during the reporting period were: (1) Continued to solicit industry research partners to provide test sites. A Cooperative Research Agreement has been signed with Oneok, for a test site in the Mocane-Laverne field in the Anadarko basin (Oklahoma). The site consists of

  2. A Unique Method of Retention for Gum Stripper- A Case Report

    PubMed Central

    T.S., Priyanka

    2014-01-01

    Successful restoration of partially edentulous situations, especially kennedy’s class-I, II &IV requires lot of contemporary and conventional treatment approaches. Semi precision attachments play a major role in retention of clinically challenging partially edentulous situation. Attachment retained partial dentures can be one of the successful treatment option in prosthdontics. This article presents a unique technique of retaining gum stripper using semi precision attachments. PMID:25654046

  3. LOW COST METHODOLOGIES TO ANALYZE AND CORRECT ABNORMAL PRODUCTION DECLINE IN STRIPPER GAS WELLS

    SciTech Connect

    Jerry James; Gene Huck; Tim Knobloch

    2001-01-01

    The goal of this research program is to develop and deliver a procedure guide of low cost methodologies to analyze and correct problems with stripper wells experiencing abnormal production declines. A study group of wells will provide data to determine the historic frequency of the problem of abnormal production declines in stripper gas wells and the historic frequency of the cases of the production problems. Once the most frequently occurring causes of the production problems are determined, data collection forms and decision trees will be designed to cost-effectively diagnose these problems and suggest corrective action. Finally, economic techniques to solve the most frequently occurring problems will be research and implemented. These systematic methodologies and techniques will increase the efficiency of problem assessment and implementation of solutions for stripper gas wells. This fifth quarterly technical report describes the data reduction and methodology to develop diagnostic tools to evaluate the cause of declines in problem wells, specifically addressing the development of data gathering forms for tubing plunger wells, casing plunger wells, pumping wells, and swab or flow wells. This report also describes the methodology to select a group of wells for field review utilizing data gathering forms developed during this quarter.

  4. Low cost methodologies to analyze and correct abnormal production decline in stripper gas wells

    SciTech Connect

    James, J.; Huck, G.; Knobloch, T.

    2000-04-01

    The goal of this research program is to develop and deliver a procedure guide of low cost methodologies to analyze and correct problems with stripper wells experiencing abnormal production declines. A study group of wells will provide data to determine the historic frequency of the problem of abnormal production declines in stripper gas wells and the historic frequency of the causes of the production problems. Once the most frequently occurring causes of the production problems are determined, data collection forms and decision trees will be designed to cost-effectively diagnose these problems and suggest corrective action. Finally, economic techniques to solve the most frequently occurring problems will be researched and implemented. These systematic methodologies and techniques will increase the efficiency of problem assessment and implementation of solutions for stripper gas wells. This second quarterly technical report describes the data reduction and methodology to develop data collection forms of pertinent information to assist in analysis of problem wells. The report also describes the procedures to categorize individual well problems. Finally, the report summarizes the frequency of individual well problems.

  5. LOW COST METHODOLOGIES TO ANALYZE AND CORRECT ABNORMAL PRODUCTION DECLINE IN STRIPPER GAS WELLS

    SciTech Connect

    Jerry James; Gene Huck; Tim Knobloch

    2001-04-01

    The goal of this research program is to develop and deliver a procedure guide of low cost methodologies to analyze and correct problems with stripper wells experiencing abnormal production declines. A study group of wells will provide data to determine the historic frequency of the problem of abnormal production declines in stripper gas wells and the historic frequency of the causes of the production problems. Once the most frequently occurring causes of the production problems are determined, data collection forms and decision trees will be designed to cost-effectively diagnose these problems and suggest corrective action. Finally, economic techniques to solve the most frequently occurring problems will be researched and implemented. These systematic methodologies and techniques will increase the efficiency of problem assessment and implementation of solutions for stripper gas wells. This sixth quarter technical progress report further describes the data reduction and methodology to develop diagnostic tools to evaluate the cause of declines in problem wells, specifically addressing the development of data gathering forms for tubing plunger wells, casing plunger wells, pumping wells, and swab or flow wells. This report also further describes the methodology to select a group of wells for field review utilizing data gathering forms further developed during this quarter.

  6. Hydrodynamic and shock heating instabilities of liquid metal strippers for RIA

    SciTech Connect

    Hassanein, Ahmed

    2013-05-24

    Stripping of accelerated ions is a key problem for the design of RIA to obtain high efficiency. Thin liquid Lithium film flow is currently considered as stripper for RIA ion beams to obtain higher Z for following acceleration: in extreme case of Uranium from Z=29 to Z=60-70 (first stripper) and from Z=70 till full stripping Z=92 (second stripper). Ionization of ion occurs due to the interaction of the ion with electrons of target material (Lithium) with the loss of parts of the energy due to ionization, Q{sub U}, which is also accompanied with ionization energy losses, Q{sub Li} of the lithium. The resulting heat is so high that can be removed not by heat conduction but mainly by convection, i.e., flowing of liquid metal across beam spot area. The interaction of the beam with the liquid metal generates shock wave propagating along direction perpendicular to the beam as well as excites oscillations along beam direction. We studied the dynamics of these excited waves to determine conditions for film stability at the required velocities for heat removal. It will allow optimizing jet nozzle shapes and flow parameters to prevent film fragmentation and to ensure stable device operation.

  7. LOW COST METHODOLOGIES TO ANALYZE AND CORRECT ABNORMAL PRODUCTION DECLINE IN STRIPPER GAS WELLS

    SciTech Connect

    Jerry James; Gene Huck; Tim Knobloch

    2001-10-01

    A study group of 376 Clinton Sand wells in Ohio provided data to determine the historic frequency of the problem of abnormal production declines in stripper gas wells and the causes of the abnormal production decline. Analysis of the historic frequency of the problem indicates over 70% of the wells experienced abnormal production decline. The most frequently occurring causes of abnormal production declines were determined to be fluid accumulation (46%), gas gathering restrictions (24%), and mechanical failures (23%). Data collection forms and decision trees were developed to cost-effectively diagnose the abnormal production declines and suggest corrective action. The decision trees and data collection sheets were incorporated into a procedure guide to provide stripper gas well operators with a methodology to analyze and correct abnormal production declines. The systematic methodologies and techniques developed should increase the efficiency of problem well assessment and implementation of solutions for stripper gas wells. This eight quarterly technical progress report provides a summary of the deliverables completed to date, including the results of the remediations, the procedure guide, and the technology transfer. Due to the successful results of the study to date and the efficiency of the methodology development, two to three additional wells will be selected for remediation for inclusion into the study. The results of the additional remediations will be included in the final report.

  8. LOW COST METHODOLOGIES TO ANALYZE AND CORRECT ABNORMAL PRODUCTION DECLINE IN STRIPPER GAS WELLS

    SciTech Connect

    Jerry James; Gene Huck; Tim Knobloch

    2001-12-01

    A study group of 376 Clinton Sand wells in Ohio provided data to determine the historic frequency of the problem of abnormal production declines in stripper gas wells and the causes of the abnormal production decline. Analysis of the historic frequency of the problem indicates over 70% of the wells experienced abnormal production decline. The most frequently occurring causes of abnormal production declines were determined to be fluid accumulation (46%), gas gathering restrictions (24%), and mechanical failures (23%). Data collection forms and decision trees were developed to cost-effectively diagnose the abnormal production declines and suggest corrective action. The decision trees and data collection sheets were incorporated into a procedure guide to provide stripper gas well operators with a methodology to analyze and correct abnormal production declines. The systematic methodologies and techniques developed should increase the efficiency of problem well assessment and implementation of solutions for stripper gas wells. This final technical progress report provides a summary of the deliverables completed to date, including the results of the remediations, the procedure guide, and the technology transfer. Due to the successful results of the study to date and the efficiency of the methodology development, two additional wells were selected for remediation and included into the study. Furthermore, the remediation results of wells that were a part of the study group of wells are also described.

  9. Foil support structure for large electron guns

    SciTech Connect

    Brucker, J.P.; Rose, E.A.

    1993-08-01

    This paper describes a novel support structure for a vacuum diode used to pump a gaseous laser with an electron beam. Conventional support structures are designed to hold a foil flat and rigid. This new structure takes advantage of the significantly greater strength of metals in pure tension, utilizing curved shapes for both foil and support structure. The shape of the foil is comparable to the skin of a balloon, and the shape of the support structures is comparable to the cables of a suspension bridge. This design allows a significant reduction in foil thickness and support structure mass, resulting in a lower electron-beam loss between diode and laser gas. In addition, the foil is pre-formed in the support structure at pressures higher than operating pressure. Therefore, the foil is operated far from the yield point. Increased reliability is anticipated.

  10. Consortium for Petroleum & Natural Gas Stripper Wells PART 2 OF 3

    SciTech Connect

    Morrison, Joel

    2011-12-01

    The United States has more oil and gas wells than any other country. As of December 31, 2004, there were more than half a million producing oil wells in the United States. That is more than three times the combined total for the next three leaders: China, Canada, and Russia. The Stripper Well Consortium (SWC) is a partnership that includes domestic oil and gas producers, service and supply companies, trade associations, academia, the Department of Energy’s Strategic Center for Natural Gas and Oil (SCNGO) at the National Energy Technology Laboratory (NETL), and the New York State Energy Research and Development Authority (NYSERDA). The Consortium was established in 2000. This report serves as a final technical report for the SWC activities conducted over the May 1, 2004 to December 1, 2011 timeframe. During this timeframe, the SWC worked with 173 members in 29 states and three international countries, to focus on the development of new technologies to benefit the U.S. stripper well industry. SWC worked with NETL to develop a nationwide request-for-proposal (RFP) process to solicit proposals from the U.S. stripper well industry to develop and/or deploy new technologies that would assist small producers in improving the production performance of their stripper well operations. SWC conducted eight rounds of funding. A total of 132 proposals were received. The proposals were compiled and distributed to an industrydriven SWC executive council and program sponsors for review. Applicants were required to make a formal technical presentation to the SWC membership, executive council, and program sponsors. After reviewing the proposals and listening to the presentations, the executive council made their funding recommendations to program sponsors. A total of 64 projects were selected for funding, of which 59 were fully completed. Penn State then worked with grant awardees to issue a subcontract for their approved work. SWC organized and hosted a total of 14 meetings

  11. Consortium for Petroleum & Natural Gas Stripper Wells PART 3 OF 3

    SciTech Connect

    Morrison, Joel

    2011-12-01

    The United States has more oil and gas wells than any other country. As of December 31, 2004, there were more than half a million producing oil wells in the United States. That is more than three times the combined total for the next three leaders: China, Canada, and Russia. The Stripper Well Consortium (SWC) is a partnership that includes domestic oil and gas producers, service and supply companies, trade associations, academia, the Department of Energy’s Strategic Center for Natural Gas and Oil (SCNGO) at the National Energy Technology Laboratory (NETL), and the New York State Energy Research and Development Authority (NYSERDA). The Consortium was established in 2000. This report serves as a final technical report for the SWC activities conducted over the May 1, 2004 to December 1, 2011 timeframe. During this timeframe, the SWC worked with 173 members in 29 states and three international countries, to focus on the development of new technologies to benefit the U.S. stripper well industry. SWC worked with NETL to develop a nationwide request-for-proposal (RFP) process to solicit proposals from the U.S. stripper well industry to develop and/or deploy new technologies that would assist small producers in improving the production performance of their stripper well operations. SWC conducted eight rounds of funding. A total of 132 proposals were received. The proposals were compiled and distributed to an industrydriven SWC executive council and program sponsors for review. Applicants were required to make a formal technical presentation to the SWC membership, executive council, and program sponsors. After reviewing the proposals and listening to the presentations, the executive council made their funding recommendations to program sponsors. A total of 64 projects were selected for funding, of which 59 were fully completed. Penn State then worked with grant awardees to issue a subcontract for their approved work. SWC organized and hosted a total of 14 meetings

  12. Technical Development Path for Foil Gas Bearings

    NASA Technical Reports Server (NTRS)

    DellaCorte, Christopher

    2008-01-01

    Foil gas bearings are in widespread commercial use in air cycle machines, turbocompressors and microturbine generators and are emerging in more challenging applications such as turbochargers, auxiliary power units and propulsion gas turbines. Though not well known, foil bearing technology is well over fifty years old. Recent technological developments indicate that their full potential has yet to be realized. This paper investigates the key technological developments that have characterized foil bearing advances. It is expected that a better understanding of foil gas bearing development path will aid in future development and progress towards more advanced applications.

  13. Free Surface and Flapping Foil Interactions

    NASA Astrophysics Data System (ADS)

    Ananthakrishnan, Palaniswamy

    2014-11-01

    Flapping foils for station-keeping of a near-surface body in a current is analyzed using a finite-difference method based on boundary-fitted coordinates. The foils are hinge-connected to the aft of the body and subject to pitch oscillation. Results are obtained for a range of Strouhal number, Froude number, unsteady frequency parameter τ, Reynolds number and the depth of foil submergence. Results show that at low Strouhal number (St < 0 . 1) and sub-critical unsteady parameter τ < 0 . 25 , the flapping generates drag instead of thrust. At high Strouhal number and super-critical value of the unsteady parameter (τ > 0 . 25) flapping generates high thrust with low efficiency. Thrust and efficiency are found to decrease with decreasing submergence depth of the foil. At the critical τ = 0 . 25 and shallow submergence of the foil, the standing wave generated above the foil continues to grow until breaking; both the thrust and efficiency of the foil are reduced at the critical τ. The necessary conditions for optimal thrust generation by a flapping foil underneath the free surface are found to be (i) Strouhal number in the range from 0.25 to 0.35, (ii) unsteady parameter τ > 0 . 25 and (iii) the maximum angle of attack less than 15° for the flat-plate foil. Supported by the US Office of Naval Research through the Naval Engineering Education Center (NEEC) Consortium of the University of Michigan, Ann Arbor.

  14. SELECTION AND TREATMENT OF STRIPPER GAS WELLS FOR PRODUCTION ENHANCEMENT IN THE MID-CONTINENT

    SciTech Connect

    Scott Reeves

    2003-03-01

    Stripper gas wells are an important source of domestic energy supply and under constant threat of permanent loss (shut-in) due to marginal economics. In 1998, 192 thousand stripper gas wells produced over a Tcf of gas, at an average rate of less than 16 Mcfd. This represents about 57% of all producing gas wells in the onshore lower-48 states, yet only 8% of production. Reserves of stripper gas wells are estimated to be only 1.6 Tcf, or slightly over 1% of the onshore lower-48 total (end of year 1996 data). Obviously, stripper gas wells are at the very margin of economic sustenance. As the demand for natural gas in the U.S. grows to the forecasted estimate of over 30 Tcf annually by the year 2010, supply from current conventional sources is expected to decline. Therefore, an important need exists to fully exploit known domestic resources of natural gas, including those represented by stripper gas wells. The overall objectives of this project are to develop an efficient and low-cost methodology to broadly categorize the well performance characteristics for a stripper gas field, identify the high-potential candidate wells for remediation, and diagnose the specific causes for well underperformance. With this capability, stripper gas well operators can more efficiently and economically produce these resources and maximize these gas reserves. A further objective is to identify/develop, evaluate and test ''new and novel,'' economically viable remediation options. Finally, it is the objective of this project that all the methods and technologies developed in this project, while being tested in the Mid-Continent, be widely applicable to stripper gas wells of all types across the country. The project activities during the reporting period were: (1) Prepared various materials to describe the project for promotional purposes and to attract potential industry partners. Materials included slides for DOE's displays at the SPE Eastern Regional and Annual Technical Conference, and

  15. Foil bearing lubrication theory including compressibility effects

    NASA Technical Reports Server (NTRS)

    Gorla, Rama Subba Reddy; Catalano, Daniel A.

    1987-01-01

    An analysis is presented to determine the film thickness in a foil bearing. Using the Reynolds equation and including the compressibility effects of the gas, an equation was developed applicable to the film thickness in a foil bearing. The bearing was divided into three regions, namely, the entrance region, middle region and exit region. Solutions are obtained for the film thickness in each region.

  16. Chromic acid anodizing of aluminum foil

    NASA Technical Reports Server (NTRS)

    Dursch, H.

    1988-01-01

    The success of the Space Station graphite/epoxy truss structure depends on its ability to endure long-term exposure to the LEO environment, primarily the effects of atomic oxygen and the temperture cycling resulting from the 94 minute orbit. This report describes the development and evaluation of chromic acid anodized (CAA) aluminum foil as protective coatings for these composite tubes. Included are: development of solar absorptance and thermal emittance properties required of Al foil and development of CAA parameters to achieve these optical properties; developing techniques to CAA 25 ft lengths of Al foil; developing bonding processes for wrapping the Al foil to graphite/epoxy tubes; and atomic oxygen testing of the CAA Al foil. Two specifications were developed and are included in the report: Chromic Acid Anodizing of Aluminum Foil Process Specification and Bonding of Anodized Aluminum Foil to Graphite/Epoxy Tubes. Results show that CAA Al foil provides and excellent protective and thermal control coating for the Space Station truss structure.

  17. Hot foil transducer skin friction sensor

    NASA Technical Reports Server (NTRS)

    Vranas, T. (Inventor)

    1982-01-01

    The device utilizes foil transducers with only one edge exposed to the fluid flow. The surfaces are polished producing a foil transducer that does not generate turbulence while sufficiently thick to carry the required electrical current for high temperature fluid flow. The assembly utilizes a precut layered metal sandwich with attached electrodes eliminating a need for welding and individual sensor calibration.

  18. Barrier Foil Heating Simulations Using LASNEX

    SciTech Connect

    Ho, D D

    2002-03-12

    It is necessary to place a barrier foil in front of the X-ray converter target to prevent the backstreaming ions. This research note presents the simulations of foil heating using the latest EOS tables. LASNEX simulations are carried out using both DARHT-II and ETA-II beam parameters. Results for all the foils studied here, using the DARHT-II beam parameters, show that the integrated line density along the axis at the end of the 4th pulse remains essentially unchanged even if the foils are heated by beams with relatively small beam spot sizes. The temperature can reach up to 3000 C on graphite foil but can only reach several hundred degree Celsius on Mylar foil. Simulations also show that ETA-II beam can create a ''burn-through'' hole on all the foils except graphite and diamond foils, which may require pre-heat. The threshold beam spot size required for hole formation will be compared with LASNEX simulation for the purpose of code verification.

  19. Nuclear Propulsion using Thin Foiled Fuel

    NASA Astrophysics Data System (ADS)

    Takahashi, H.

    1998-11-01

    A new way to produce plasma for nuclear propulsion is proposed. A thin foiled fuel can be used for converting fission energy to propulsion energy efficiently. The fission products coming out of the thin foil directly ionize the hydrogen molecules which are used for propulsion. Thus very small portion of fission energy deposited in the thin foil, and integrity of the thin foiled fuel can be maintained even in high nuclear power. Fuel material with large thermal fission cross-section is preferable to make thin foiled fuel and the heat deposition in the foil can be reduced. To get high power from the foiled fuel assembly, thermal neutrons which are created out from the assembly can be supplied, or the assembly itself can create the high intensity thermal neutrons by self-multiplication. A flexible design of a highly efficient nuclear propulsion system can be made. The thickness of the foil and the maintenance of the thermo-mechanical integrity can be determined from the fission cross-section and the slowing down power for fission products. The talk discusses the issues related to heat removal from the assembly.

  20. S.1919: Federal Oil and Gas Stripper Well Preservation Act of 1998, introduced in the US Senate, One Hundred Fifth Congress, Second Session, April 2, 1998

    SciTech Connect

    1998-12-31

    The purpose of this bill is to provide for the energy security of the Nation through encouraging the production of domestic oil and gas resources from stripper wells on Federal lands, and for other purposes. The law would authorize reduction of royalty rates for stripper wells on federal lands and suspend minimum royalty and per acre rental fees.

  1. A Preliminary Foil Gas Bearing Performance Map

    NASA Technical Reports Server (NTRS)

    DellaCorte, Christopher; Radil, Kevin C.; Bruckner, Robert J.; Howard, S. Adam

    2006-01-01

    Recent breakthrough improvements in foil gas bearing load capacity, high temperature tribological coatings and computer based modeling have enabled the development of increasingly larger and more advanced Oil-Free Turbomachinery systems. Successful integration of foil gas bearings into turbomachinery requires a step wise approach that includes conceptual design and feasibility studies, bearing testing, and rotor testing prior to full scale system level demonstrations. Unfortunately, the current level of understanding of foil gas bearings and especially their tribological behavior is often insufficient to avoid developmental problems thereby hampering commercialization of new applications. In this paper, a new approach loosely based upon accepted hydrodynamic theory, is developed which results in a "Foil Gas Bearing Performance Map" to guide the integration process. This performance map, which resembles a Stribeck curve for bearing friction, is useful in describing bearing operating regimes, performance safety margins, the effects of load on performance and limiting factors for foil gas bearings.

  2. ESTABLISHMENT OF AN INDUSTRY-DRIVEN CONSORTIUM FOCUSED ON IMPROVING THE PRODUCTION PERFORMANCE OF DOMESTIC STRIPPER WELLS

    SciTech Connect

    Joel L. Morrison

    2003-04-08

    The Pennsylvania State University, under contract to the U.S. Department of Energy, National Energy Technology Laboratory will establish, promote, and manage a national industry-driven Stripper Well Consortium (SWC) that will be focused on improving the production performance of domestic petroleum and/or natural gas stripper wells. The consortium creates a partnership with the U.S. petroleum and natural gas industries and trade associations, state funding agencies, academia, and the National Energy Technology Laboratory. This report serves as the ninth quarterly technical progress report for the SWC. Key activities for this reporting period include: (1) organizing and hosting two fall technology transfer meetings, (2) SWC membership class expansion, and (3) planning the SWC 2003 Spring meeting. In addition, a literature search that focuses on the use of lasers, microwaves, and acoustics for potential stripper well applications continued.

  3. Establishment of an Industry-Driven Consortium Focused on Improving the Production Performance of Domestic Stripper Wells

    SciTech Connect

    Joel Morrison; Sharon Elder

    2006-01-24

    The Pennsylvania State University, under contract to the U.S. Department of Energy, National Energy Technology Laboratory will establish, promote, and manage a national industry-driven Stripper Well Consortium (SWC) that will be focused on improving the production performance of domestic petroleum and/or natural gas stripper wells. The consortium creates a partnership with the U.S. petroleum and natural gas industries and trade associations, state funding agencies, academia, and the National Energy Technology Laboratory. This report serves as the sixth quarterly technical progress report for the SWC. Key activities for this reporting period included: (1) Organized and hosted two technology transfer meetings; (2) Collaborated with the Pennsylvania Oil and Gas Association (POGAM) to host a Natural Gas Outlook conference in Pittsburgh, PA; (3) Provided a SWC presentation at the Interstate Oil and Gas Compact Commission (IOGCC) meeting in Jackson Hole, WY; and (4) Completed and released a stripper well industry documentary entitled: ''Independent Oil: Rediscovering America's Forgotten Wells''.

  4. Low cost methodologies to analyze and correct abnormal production decline in stripper gas wells

    SciTech Connect

    James, J.; Huck, G.; Knobloch, T.

    2000-07-01

    The goal of this research program is to develop and deliver a procedure guide of low cost methodologies to analyze and correct problems with stripper wells experiencing abnormal production declines. A study group of wells will provide data to determine the historic frequency of the problem of abnormal production declines in stripper gas wells and the historic frequency of the causes of the production problems. Once the most frequently occurring causes of the production problems are determined, data collection forms and decision trees will be designed to cost-effectively diagnose these problems and suggest corrective action. Finally, economic techniques to solve the most frequently occurring problems will be researched and implemented. These systematic methodologies and techniques will increase the efficiency of problem assessment and implementation of solutions for stripper gas wells. This third quarterly technical report was to describe the data reduction and methodologies to develop decision trees, identify cost effective techniques to solve the most frequently experienced problems and then apply the methodology to a group of wells where recent problems have developed. Further, this third quarterly technical report was to describe the data reduction and methodologies to select the two wells with the greatest potential for increase and also having the most frequently occurring problem, and evaluate the results of the methodology and the implemented procedure. However, preparation and analysis of the decision trees is more complex than initially anticipated due to the combination of problems rather than identifiable individual problems. Therefore, this portion of the study is still in progress. We have requested and been granted verbal approval for a six month no cost extension to allow more time to thoroughly investigate this portion of the study. The delivery of the decision trees will be included in future technical reports. Work on the other tasks to be

  5. LOW COST METHODOLOGIES TO ANALYZE AND CORRECT ABNORMAL PRODUCTION DECLINE IN STRIPPER GAS WELLS

    SciTech Connect

    Jerry James; Gene Huck; Tim Knobloch

    2001-07-01

    The goal of this research program is to develop and deliver a procedure guide of low cost methodologies to analyze and correct problems with stripper wells experiencing abnormal production declines. A study group of wells will provide data to determine the historic frequency of the problem of abnormal production declines in stripper gas wells and the historic frequency of the causes of the production problems. Once the most frequently occurring causes of the production problems are determined, data collection forms and decision trees will be designed to cost-effectively diagnose these problems and suggest corrective action. Finally, economic techniques to solve the most frequently occurring problems will be researched and implemented. These systematic methodologies and techniques will increase the efficiency of problem assessment and implementation of solutions for stripper gas wells. This seventh quarterly technical progress report further describes the data reduction and methodology to develop diagnostic tools to evaluate the cause of declines in problem wells, specifically addressing the methodology to analyze the group of wells where recent problems have occurred utilizing the data gathering forms. This report also describes the methodology to select the two wells with the greatest potential for increase and also having the most frequently occurring problem. Finally, this report describes the preliminary results of the remediation applied to the two wells selected. Two wells selected and analyzed from a twenty-four well study group indicated that their current abnormal production decline was attributable to fluid build-up in the wellbore. Subsequent remediation work of putting both wells on pump to reduce fluid build-up in the well bore decreased the flowing bottom hole pressure and increased gas production dramatically.

  6. Assembly Methods for Etched Foil Regenerators

    NASA Astrophysics Data System (ADS)

    Mitchell, Matthew P.

    2004-06-01

    Etched foil appears to offer substantial advantages over other regenerator materials, especially for annular regenerators. However, assembly of etched foil regenerators has been difficult because etching regenerator patterns in foil is most satisfactorily accomplished using pieces too small for a complete, spiral-wrapped regenerator. Two techniques have been developed to deal with that problem: For spiral-wrapped regenerators, a new technique for joining pieces of foil using tabs has been successfully employed. The joints are no thicker than the parent material. The tabs substantially fill the holes into which they are locked, virtually eliminating any undesired leak path through the regenerator. The holes constitute breaks in the conductive path through the regenerator. A patent is pending. An alternate method is to insert pieces of foil in a cylindrical housing one at a time. An inflatable bladder presses each newly-inserted piece of foil against the previous layer until both edges slip past each other and contact the previously-installed piece. When the bladder is deflated, the natural springiness of the foil causes the cut edges to seek the wall and meet each other in a butt joint. A patent on the method has been issued; a patent on the resulting regenerator is pending.

  7. Beam-single and beam-two-foil experimental facility to study physics of highly charged ions

    SciTech Connect

    Ahmad, Nissar; Wani, A.A.; Ram, R.; Abhilash, S.R.; Kumar, Rakesh; Patnaik, J.K.; De, Sankar; Karn, R.K.; Nandi, T.

    2006-03-15

    A facility for lifetime measurement of metastable states in highly charged ions using the beam-foil technique with a single-foil and a two-foil target has been developed. In the two-foil technique, one foil moves with respect to the other and the option of varying the thickness of the fixed foil online has been implemented. A holder with multiple foils is used as a fixed target, and moved along x, y, and {theta}, the angle of rotation with respect to beam direction along the z axis. Using this facility, the He-like 1s2p {sup 3}P{sub 2}{sup o} and Li-like 1s2s2p {sup 4}P{sub 5l/2}{sup o} titanium lifetimes have been measured and compared with earlier values. In addition to this, the processes which occur when excited states collide with carbon foils of different thicknesses have also been investigated. Preliminary results suggest the scope of studying intrashell transitions during ion-solid collision using this setup. In this article, the setup is described in detail and representative results are briefly discussed.

  8. An overview of the Noncyanide Metal Stripper program conducted at Kelly Air Force Base

    SciTech Connect

    Argyle, M.D.; Cowan, R.L.

    1995-01-01

    The Noncyanide Metal Stripper Program was a waste minimization effort aimed at identifying and testing suitable noncyanide stripping solutions that could replace the cyanide stripping solutions found in the United States Air Force (USAF) Air Logistics Centers (ALC). The program started with laboratory testing of commercial stripping solutions. The performance of these solutions was compared with the cyanide process solutions C-101 and C-106 targeted for replacement. Plate metal stripping rate, basis metal corrosion, and compatibility with masking materials and biodegradability were all used to determine the performance of each product. Those products that passed the acceptance criteria were field tested using 25 to 50-gallon solutions to determine optimum operating conditions, stripper maintenance requirements, and maximum solution loading and longevity. The program included investigating any adverse effects these new products might have on existing chemical and biological waste treatment processes. All cyanide stripping solutions at the San Antonio Air Logistics Command Center have been successfully replaced with commercial noncyanide products. Generally, these replacements were less toxic and generated less waste and had longer lifetimes than their cyanide counterparts.

  9. Treatability test of a stacked-tray air stripper for VOC in water

    SciTech Connect

    Pico, T., LLNL

    1998-04-01

    A common strategy for hydraulic containment and mass removal at VOC contaminated sites is `pump and treat (P&T)`. In P&T operations, contaminated ground water is pumped from wells, treated above ground, and discharged. Many P&T remediation systems at VOC sites rely on air stripping technology because VOCs are easily transferred to the vapor phase. In stacked-tray air strippers, contaminated water is aerated while it flows down through a series of trays. System operations at LLNL are strictly regulated by the California and federal Environmental Protection Agencies (Cal/EPA and EPA), the Bay Area Air Quality Management District (BAAQMD), the California Regional Water Quality Control Board (RWQCB) and the Department of Toxic Substances Control (DTSC). These agencies set discharge limits, require performance monitoring, and assess penalties for non-compliance. National laboratories are also subject to scrutiny by the public and other government agencies. This extensive oversight makes it necessary to accurately predict field treatment performance at new extraction locations to ensure compliance with all requirements prior to facility activation. This paper presents treatability test results for a stacked- tray air stripper conducted at LLNL and compares them to the vendor`s modeling software results.

  10. Reactive multilayer synthesis of hard ceramic foils and films

    DOEpatents

    Makowiecki, D.M.; Holt, J.B.

    1996-02-13

    A method is disclosed for synthesizing hard ceramic materials such as carbides, borides and aluminides, particularly in the form of coatings provided on another material so as to improve the wear and abrasion performance of machine tools, for example. The method involves the sputter deposition of alternating layers of reactive metals with layers of carbon, boron, or aluminum and the subsequent reaction of the multilayered structure to produce a dense crystalline ceramic. The material can be coated on a substrate or formed as a foil which can be coiled as a tape for later use.

  11. Reactive multilayer synthesis of hard ceramic foils and films

    DOEpatents

    Makowiecki, Daniel M.; Holt, Joseph B.

    1996-01-01

    A method for synthesizing hard ceramic materials such as carbides, borides nd aluminides, particularly in the form of coatings provided on another material so as to improve the wear and abrasion performance of machine tools, for example. The method involves the sputter deposition of alternating layers of reactive metals with layers of carbon, boron, or aluminum and the subsequent reaction of the multilayered structure to produce a dense crystalline ceramic. The material can be coated on a substrate or formed as a foil which can be coild as a tape for later use.

  12. Synthetic Graphene Grown by Chemical Vapor Deposition on Copper Foils

    NASA Astrophysics Data System (ADS)

    Chung, Ting Fung; Shen, Tian; Cao, Helin; Jauregui, Luis A.; Wu, Wei; Yu, Qingkai; Newell, David; Chen, Yong P.

    2013-04-01

    The discovery of graphene, a single layer of covalently bonded carbon atoms, has attracted intense interest. Initial studies using mechanically exfoliated graphene unveiled its remarkable electronic, mechanical and thermal properties. There has been a growing need and rapid development in large-area deposition of graphene film and its applications. Chemical vapor deposition on copper has emerged as one of the most promising methods in obtaining large-scale graphene films with quality comparable to exfoliated graphene. In this paper, we review the synthesis and characterizations of graphene grown on copper foil substrates by atmospheric pressure chemical vapor deposition. We also discuss potential applications of such large-scale synthetic graphene.

  13. Reactive multilayer synthesis of hard ceramic foils and films

    SciTech Connect

    Makowiecki, D.M.; Holt, J.B.

    1993-12-31

    Disclosed is method for synthesizing hard ceramic materials such as carbides, borides and aluminides, particularly in the form of coatings provided on another material so as to improve the wear and abrasion performance of machine tools, for example. Method involves the sputter deposition of alternating layers of reactive metals with layers of carbon, boron, or aluminum and the subsequent reaction of the multilayered structure to produce a dense crystalline ceramic. The material can be coated on a substrate or formed as a foil which can be coiled as a tape for later use.

  14. Bonded Invar Clip Removal Using Foil Heaters

    NASA Technical Reports Server (NTRS)

    Pontius, James T.; Tuttle, James G.

    2009-01-01

    A new process uses local heating and temperature monitoring to soften the adhesive under Invar clips enough that they can be removed without damaging the composite underneath or other nearby bonds. Two 1x1 in. (approx.2.5x2.5 cm), 10-W/sq in. (approx.1.6-W/sq cm), 80-ohm resistive foil Kapton foil heaters, with pressure-sensitive acrylic adhesive backing, are wired in parallel to a 50-V, 1-A limited power supply. At 1 A, 40 W are applied to the heater pair. The temperature is monitored in the clip radius and inside the tube, using a dual thermocouple readout. Several layers of aluminum foil are used to speed the heat up, allowing clips to be removed in less than five minutes. The very local heating via the foil heaters allows good access for clip removal and protects all underlying and adjacent materials.

  15. Application of foil bearings to helium turbocompressor

    SciTech Connect

    Chen, H.Ming; Howarth, R.; Bernard, Geren; Theilacker, Jay C.; Soyars, William M.; /Fermilab

    2001-01-01

    Hydrodynamic gas-lubricated foil bearings are ideal for machinery that operates at high speed or in extreme-temperature environments. As motors and generators run at higher speeds with more torque capacity, the need for commonly available, robust, high-speed, low-loss foil bearings is clear. This paper presents an application example of the successful replacement of a tape-type bearing for a bump-type bearing in a helium turbocompressor. Both bearing types are described, as are the steps involved in design and fabrication of the bump bearing, and results of comparison tests between the original and replacement bearings. Methods to analyze bump-type foil bearings with commercially available software are reviewed to further emphasize the inherent simplicity of these bearings. By providing the engineering community with the understanding needed to successfully apply foil bearings, the authors hope that the benefits and true potential of this technology will finally be realized.

  16. 75 FR 61624 - Promotion of Development, Reduction of Royalty Rates for Stripper Well and Heavy Oil Properties

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-10-06

    ... CFR 3103.4-3). The BLM promulgated the latter two provisions in 1992 and 1996, respectively (57 FR 35973 (Aug. 11, 1992); 61 FR 4750 (Feb. 8, 1996)). A stripper well property, within the meaning of... properties (70 FR 42093 (July 21, 2005)). The BLM suspended and subsequently terminated the program for...

  17. Experimental evaluation of foil-supported resilient-pad gas-lubricated thrust bearing

    NASA Technical Reports Server (NTRS)

    Nemeth, Z. N.

    1977-01-01

    A new type of resilient-pad gas thrust bearing was tested to determine the feasibility of the design. The bearing consists of carbon graphite pads mounted asymmetrically on foil beams. Two bearing configurations were tested at thrust loads from 27 to 80 newtons at speeds to 9000 rpm. The outside diameter of the bearing was 8.9 centimeters.

  18. SELECTION AND TREATMENT OF STRIPPER GAS WELLS FOR PRODUCTION ENHANCEMENT, MOCANE-LAVERNE FIELD, OKLAHOMA

    SciTech Connect

    Scott Reeves; Buckley Walsh

    2003-08-01

    In 1996, Advanced Resources International (ARI) began performing R&D targeted at enhancing production and reserves from natural gas fields. The impetus for the effort was a series of field R&D projects in the early-to-mid 1990's, in eastern coalbed methane and gas shales plays, where well remediation and production enhancement had been successfully demonstrated. As a first step in the R&D effort, an assessment was made of the potential for restimulation to provide meaningful reserve additions to the U.S. gas resource base, and what technologies were needed to do so. That work concluded that: (1) A significant resource base did exist via restimulation (multiples of Tcf). (2) The greatest opportunities existed in non-conventional plays where completion practices were (relatively) complex and technology advancement was rapid. (3) Accurate candidate selection is the greatest single factor that contributes to a successful restimulation program. With these findings, a field-oriented program targeted at tight sand formations was initiated to develop and demonstrate successful candidate recognition technology. In that program, which concluded in 2001, nine wells were restimulated in the Green River, Piceance and East Texas basins, which in total added 2.9 Bcf of reserves at an average cost of $0.26/Mcf. In addition, it was found that in complex and heterogeneous reservoirs (such as tight sand formations), candidate selection procedures should involve a combination of fundamental engineering and advanced pattern recognition approaches, and that simple statistical methods for identifying candidate wells are not effective. In mid-2000, the U.S. Department of Energy (DOE) awarded ARI an R&D contract to determine if the methods employed in that project could also be applied to stripper gas wells. In addition, the ability of those approaches to identify more general production enhancement opportunities (beyond only restimulation), such as via artificial lift and compression, was

  19. Cryostat with Foil and MLI

    SciTech Connect

    Hwang, Peter K.F.; Gung, Chen-yu

    2005-10-06

    Induction cores are used to accelerate heavy ion beam array, which are built around the outer diameter of the cryostat housing the superconducting quadruple array. Compact cryostat is highly desirable to reduce the cost of the induction cores. Recent experiences in fabrication of a cryostat for single beam transport revealed that it is possible to reduce the spacing in the cryostat vacuum jacket by using low-emissivity thermal insulation material instead of conventional MLI. However, it is labor-intensive to install the new type of insulation as compared with using MLI. It is promising to build a cost-effective compact cryostat for quadruple magnet array for heavy ion beam array transport by using low-emissivity material combined with conventional MLI as radiation insulation. A matrix of insulation designs and tests will be performed as the feasibility study and for the selection of the optimal thermal insulation as the Phase I work. The selected mixed insulation will be used to build prototype compact cryostats in the Phase II project, which are aiming for housing quadruple doublet array. In this STTR phase I study, a small cryostat has been designed and built to perform calorimetric characterization of the heat load in a liquid helium vessel insulated with a vacuum layer with a nominal clearance of 3.5 mm. The vacuum clearance resembled that used in the warm-bore beam tube region in a prototype cryostat previously built for the heavy ion beam transport experiment. The vacuum clearance was geometrically restricted with a heater shell with the temperature controlled at near 300 K. Various combinations of radiation and thermal shields were installed in the tight vacuum clearance for heat load measurements. The measured heat loads are reported and compared with previous test result using a compact vacuum layer. Further developments of the thermal insulations used in the present study are discussed. The compact cryostat with foil and MLI insulation may be used in the

  20. CO2 Capture by Absorption with Potassium Carbonate

    SciTech Connect

    Gary T. Rochelle; Eric Chen; Babatunde Oyenekan; Andrew Sexton; Jason Davis; Marcus Hilliard; Amornvadee Veawab

    2006-09-30

    The objective of this work is to improve the process for CO{sub 2} capture by alkanolamine absorption/stripping by developing an alternative solvent, aqueous K{sub 2}CO{sub 3} promoted by piperazine. Ethylenediamine was detected in a degraded solution of MEA/PZ solution, suggesting that piperazine is subject to oxidation. Stripper modeling has demonstrated that vacuum strippers will be more energy efficient if constructed short and fat rather than tall and skinny. The matrix stripper has been identified as a configuration that will significantly reduce energy use. Extensive measurements of CO{sub 2} solubility in 7 m MEA at 40 and 60 C have confirmed the work by Jou and Mather. Corrosion of carbon steel without inhibitors increases from 19 to 181 mpy in lean solutions of 6.2 m MEA/PZ as piperazine increases from 0 to 3.1 m.

  1. Air strippers and their emissions control at Superfund sites. Technical report, February-April 1987

    SciTech Connect

    Blaney, B.L.; Branscome, M.

    1988-08-01

    Air stripping, a traditional means of making slightly contaminated ground water potable, is being applied increasingly to more-severe groundwater pollution at remedial action sites. Concentrations of volatile and semivolatile compounds at such sites may reach hundreds of parts per million. As a result, several changes have resulted in air-stripping technology. New air stripping technologies are being employed to achieve very high (>99% removal of volatile compounds and to increase the removal of semivolatiles. New stripper designs are being investigated for compactness and mobility. In addition, emissions controls are being added because air-pollution impacts are larger. The paper discusses these trends and provides examples from ground-water cleanup at remedial-action sites in the United States.

  2. Status of Genesis Mo-Pt Foils

    NASA Technical Reports Server (NTRS)

    Nishiizumi, K.; Allton, J. H.; Burnett, D. S.; Butterworth, A. L.; Caffee, M. W.; Clark, B.; Jurewicz, A. J. G.; Komura, K.; Westphal, A. J.; Welten, K. C.

    2005-01-01

    A total of 8,000 sq cm of Mo-coated Pt foils were exposed to solar wind for 884 days by the Genesis mission. Solar wind ions were captured in the surface of the Mo. Our objective is the measurement of long-lived radionuclides, such as Be-10, Al-26, Cl-36, and Mn-53, and short-lived radionuclides, such as Na-22 and Mn-54, in the captured sample of solar wind. The expected flux of these nuclides in the solar wind is 100 atom/sq cm yr or less. The hard landing of the SRC (Sample Return Capsule) at UTTR (Utah Test and Training Range) has resulted in contaminated and crumpled foils. Here we present a status report and revised plan for processing the foils.

  3. Two High-Temperature Foil Journal Bearings

    NASA Technical Reports Server (NTRS)

    Zak, Michail

    2006-01-01

    An enlarged, high-temperature-compliant foil bearing has been built and tested to demonstrate the feasibility of such bearings for use in aircraft gas turbine engines. Foil bearings are attractive for use in some machines in which (1) speeds of rotation, temperatures, or both exceed maximum allowable values for rolling-element bearings; (2) conventional lubricants decompose at high operating temperatures; and/or (3) it is necessary or desirable not to rely on conventional lubrication systems. In a foil bearing, the lubricant is the working fluid (e.g., air or a mixture of combustion gases) in the space between the journal and the shaft in the machine in which the bearing is installed.

  4. Diffusion of hydrogen in zirconium foil

    SciTech Connect

    Schur, D.V.; Pishuk, V.K.; Adejev, V.M.; Zaginaichenko, S.Y.

    1998-12-31

    The authors of present research have used in experiments the atomic hydrogen and metallic foil 25--30 {micro}m thick. It has been supposed that these technical operations will permit excluding the influence of surface and diffusional processes on the rate of Me-H interaction. The series of experiments have been carried out and they confirm this assumption. It has been shown that hydrogenation reaction of zirconium foil in atomic hydrogen conforms to the topochemical model of volume segregation of interaction product, and the rate of its flow is independent of the surface processes and hydrogen diffusion in volume.

  5. Method of high-density foil fabrication

    DOEpatents

    Blue, Craig A.; Sikka, Vinod K.; Ohriner, Evan K.

    2003-12-16

    A method for preparing flat foils having a high density includes the steps of mixing a powdered material with a binder to form a green sheet. The green sheet is exposed to a high intensity radiative source adapted to emit radiation of wavelengths corresponding to an absorption spectrum of the powdered material. The surface of the green sheet is heated while a lower sub-surface temperature is maintained. An apparatus for preparing a foil from a green sheet using a radiation source is also disclosed.

  6. Compressor ported shroud for foil bearing cooling

    DOEpatents

    Elpern, David G.; McCabe, Niall; Gee, Mark

    2011-08-02

    A compressor ported shroud takes compressed air from the shroud of the compressor before it is completely compressed and delivers it to foil bearings. The compressed air has a lower pressure and temperature than compressed outlet air. The lower temperature of the air means that less air needs to be bled off from the compressor to cool the foil bearings. This increases the overall system efficiency due to the reduced mass flow requirements of the lower temperature air. By taking the air at a lower pressure, less work is lost compressing the bearing cooling air.

  7. Steel Foil Improves Performance Of Blasting Caps

    NASA Technical Reports Server (NTRS)

    Bement, Laurence J.; Perry, Ronnie; Schimmel, Morry L.

    1990-01-01

    Blasting caps, which commonly include deep-drawn aluminum cups, give significantly higher initiation performance by application of steel foils on output faces. Steel closures 0.005 in. (0.13 mm) thick more effective than aluminum. Caps with directly bonded steel foil produce fragment velocities of 9,300 ft/s (2.8 km/s) with large craters and unpredictable patterns to such degree that no attempts made to initiate explosions. Useful in military and aerospace applications and in specialized industries as mining and exploration for oil.

  8. Thrust augmentation in tandem flapping foils by foil-wake interaction

    NASA Astrophysics Data System (ADS)

    Anderson, Erik; Lauder, George

    2006-11-01

    Propulsion by pitching and heaving airfoils and hydrofoils has been a focus of much research in the field of biologically inspired propulsion. Organisms that use this sort of propulsion are self-propelled, so it is difficult to use standard experimental metrics such as thrust and drag to characterize performance. We have constructed a flapping foil robot mounted in a flume on air-bearings that allows for the determination of self-propelled speed as a metric of performance. We have used a pair of these robots to examine the impact of an upstream flapping foil on a downstream flapping foil as might apply to tandem fins of a swimming organism or in-line swimming of schooling organisms. Self-propelled speed and a force transducer confirmed significant thrust augmentation for particular foil-to-foil spacings, phase differences, and flapping frequencies. Flow visualization shows the mechanism to be related to the effective angle of attack of the downstream foil due to the structure of the wake of the upstream foil. This confirms recent computational work and the hypotheses by early investigators of fish fluid dynamics.

  9. Energy Loss of High Intensity Focused Proton Beams Penetrating Metal Foils

    NASA Astrophysics Data System (ADS)

    McGuffey, C.; Qiao, B.; Kim, J.; Beg, F. N.; Wei, M. S.; Evans, M.; Fitzsimmons, P.; Stephens, R. B.; Chen, S. N.; Fuchs, J.; Nilson, P. M.; Canning, D.; Mastrosimone, D.; Foord, M. E.

    2014-10-01

    Shortpulse-laser-driven intense ion beams are appealing for applications in probing and creating high energy density plasmas. Such a beam isochorically heats and rapidly ionizes any target it enters into warm dense matter with uncertain transport and stopping properties. Here we present experimental measurements taken with the 1.25 kJ, 10 ps OMEGA EP BL shortpulse laser of the proton and carbon spectra after passing through metal foils. The laser irradiated spherically curved C targets with intensity 4×1018 W/cm2, producing proton beams with 3 MeV slope temperature and a sharp low energy cutoff at 5 MeV which has not been observed on lower energy, shorter pulse intense lasers. The beam either diverged freely or was focused to estimated 1016 p +/cm2 ps by a surrounding structure before entering the metal foils (Al or Ag and a Cu tracer layer). The proton and ion spectra were altered by the foil depending on material and whether or not the beam was focused. Transverse proton radiography probed the target with ps temporal and 10 micron spatial resolution, indicating an electrostatic field on the foil may also have affected the beam. We present complementary particle-in-cell simulations of the beam generation and transport to the foils. This work was supported by the DOE/NNSA National Laser User Facility program, Contract DE-SC0001265.

  10. Tight, Flat, Smooth, Ultrathin Metal Foils for Locating Synchrotron Beams

    NASA Astrophysics Data System (ADS)

    Jolivet, Connie S.; Stoner, John O.

    2007-01-01

    It is often desired to locate a synchrotron x-ray beam precisely in space with minimal disturbance of its spatial profile and spectral content. This can be done by passing the beam through an ultrathin, flat, smooth metal foil having well-defined composition, preferably a single chemical element such as chromium, titanium or aluminum. Localized fluorescence of the foil at characteristic x-ray lines where the x-ray beam passes through the foil serves to locate the beam in two dimensions. Use of two such foils along the beam direction locates the x-ray beam spatially and identifies precisely its direction. The accuracy of determining these parameters depends in part upon high uniformity in the thickness of the foil(s), good planarity, and smoothness of the foil(s). In practice, several manufacturing steps to produce a foil must be carried out with precision. The foil must be produced on a smooth removable substrate in such a way that its thickness (or areal density) is as uniform as possible. The foil must be fastened to a support ring that maintains the foil's surface quality, and it must be then stretched onto a frame that produces the desired mirror flatness. These steps are illustrated and some of the parameters specifying the quality of the resulting foils are identified.

  11. ESTABLISHMENT OF AN INDUSTRY-DRIVEN CONSORTIUM FOCUSED ON IMPROVING THE PRODUCTION PERFORMANCE OF DOMESTIC STRIPPER WELLS

    SciTech Connect

    Joel L. Morrison

    2001-09-14

    The Pennsylvania State University, under contract to the US Department of Energy, National Energy Technology Laboratory will establish, promote, and manage a national industry-driven stripper Well Consortium (SWC) that will be focused on improving the production performance of domestic petroleum and/or natural gas stripper wells. The consortium creates a partnership with the US petroleum and natural gas industries and trade associations, state funding agencies, academia, and the National Energy Technology Laboratory. This report serves as the four quarterly technical progress report for the SWC. During this reporting period, Penn State primary focus was on finalizing all subcontracts, planning the SWC technology transfer meeting and two workshops in the southern US, and preparing the next SWC newsletter. Membership in the SWC now stands at 49.

  12. ESTABLISHMENT OF AN INDUSTRY-DRIVEN CONSORTIUM FOCUSED ON IMPROVING THE PRODUCTION PERFORMANCE OF DOMESTIC STRIPPER WELLS

    SciTech Connect

    Joel L. Morrison

    2004-05-18

    The Pennsylvania State University, under contract to the U.S. Department of Energy, National Energy Technology Laboratory will establish, promote, and manage a national industry-driven Stripper Well Consortium (SWC) that will be focused on improving the production performance of domestic petroleum and/or natural gas stripper wells. The consortium creates a partnership with the U.S. petroleum and natural gas industries and trade associations, state funding agencies, academia, and the National Energy Technology Laboratory. This report serves as the fourteenth quarterly technical progress report for the SWC. Key activities for this reporting period include: (1) organizing the SWC spring meeting in Golden Colorado, (2) planning of the upcoming SWC fall technology transfer meetings, and (3) recruit the SWC base membership.

  13. Establishment of an Industry-Driven Consortium Focused on Improving the Production Performance of Domestic Stripper Wells

    SciTech Connect

    Joel L. Morrison

    2005-08-26

    The Pennsylvania State University, under contract to the U.S. Department of Energy, National Energy Technology Laboratory will establish, promote, and manage a national industry-driven Stripper Well Consortium (SWC) that will be focused on improving the production performance of domestic petroleum and/or natural gas stripper wells. The consortium creates a partnership with the U.S. petroleum and natural gas industries and trade associations, state funding agencies, academia, and the National Energy Technology Laboratory. This report serves as the eighteenth quarterly technical progress report for the SWC. Key activities for this reporting period include: (1) prepare presentation for the 16th Annual Oil Recovery Conference in Wichita, Kansas, (2) continued working on the SWC technical bulletin ''Keeping the Home Wells Flowing: Helping Small Independent Oil and Gas Producers Develop New Technology Solutions'', (3) continue efforts on the Public Broadcast of Independent Oil: Rediscovering America's Forgotten Wells, and (4) continue efforts to recruit SWC members.

  14. ESTABLISHMENT OF AN INDUSTRY-DRIVEN CONSORTIUM FOCUSED ON IMPROVING THE PRODUCTION PERFORMANCE OF DOMESTIC STRIPPER WELLS

    SciTech Connect

    Joel L. Morrison

    2005-01-04

    The Pennsylvania State University, under contract to the U.S. Department of Energy, National Energy Technology Laboratory will establish, promote, and manage a national industry-driven Stripper Well Consortium (SWC) that will be focused on improving the production performance of domestic petroleum and/or natural gas stripper wells. The consortium creates a partnership with the U.S. petroleum and natural gas industries and trade associations, state funding agencies, academia, and the National Energy Technology Laboratory. This report serves as the seventeenth quarterly technical progress report for the SWC. Key activities for this reporting period include: (1) organizing and hosting the SWC fall technology transfer meetings in Oklahoma City, Oklahoma and State College, Pennsylvania, (2) planning of the upcoming SWC spring proposal meeting, (3) release of the SWC Request-for-proposals (RFP), (4) revision of the SWC By-Laws, and (5) the SWC Executive Council nomination and election for 2005-2006 term members.

  15. ESTABLISHMENT OF AN INDUSTRY-DRIVEN CONSORTIUM FOCUSED ON IMPROVING THE PRODUCTION PERFORMANCE OF DOMESTIC STRIPPER WELLS

    SciTech Connect

    Joel L. Morrison

    2004-12-28

    The Pennsylvania State University, under contract to the U.S. Department of Energy, National Energy Technology Laboratory will establish, promote, and manage a national industry-driven Stripper Well Consortium (SWC) that will be focused on improving the production performance of domestic petroleum and/or natural gas stripper wells. The consortium creates a partnership with the U.S. petroleum and natural gas industries and trade associations, state funding agencies, academia, and the National Energy Technology Laboratory. This report serves as the sixteenth quarterly technical progress report for the SWC. Key activities for this reporting period include: (1) exhibit and participate in the Society of Petroleum Engineers (SPE) Regional Meeting in Charleston West Virginia, (2) finalize the organization of the two fall Technology Transfer meetings and (3) initiate the revision of the SWC By-laws.

  16. ESTABLISHMENT OF AN INDUSTRY-DRIVEN CONSORTIUM FOCUSED ON IMPROVING THE PRODUCTION PERFORMANCE OF DOMESTIC STRIPPER WELLS

    SciTech Connect

    Joel L. Morrison

    2005-01-03

    The Pennsylvania State University, under contract to the U.S. Department of Energy, National Energy Technology Laboratory will establish, promote, and manage a national industry-driven Stripper Well Consortium (SWC) that will be focused on improving the production performance of domestic petroleum and/or natural gas stripper wells. The consortium creates a partnership with the U.S. petroleum and natural gas industries and trade associations, state funding agencies, academia, and the National Energy Technology Laboratory. This report serves as the second quarterly technical progress report for the SWC. Key activities for this reporting period include: (1) exhibit and participate in the Society of Petroleum Engineers (SPE) Regional Meeting in Charleston WV, (2) host the SWC fall technology transfer meeting in Oklahoma City, OK and finalize the organization of the State College, PA fall Technology Transfer meeting, and (3) initiate the revision of the SWC By-laws.

  17. ESTABLISHMENT OF AN INDUSTRY-DRIVEN CONSORTIUM FOCUSED ON IMPROVING THE PRODUCTION PERFORMANCE OF DOMESTIC STRIPPER WELLS

    SciTech Connect

    Joel L. Morrison

    2004-05-17

    The Pennsylvania State University, under contract to the U.S. Department of Energy, National Energy Technology Laboratory will establish, promote, and manage a national industry-driven Stripper Well Consortium (SWC) that will be focused on improving the production performance of domestic petroleum and/or natural gas stripper wells. The consortium creates a partnership with the U.S. petroleum and natural gas industries and trade associations, state funding agencies, academia, and the National Energy Technology Laboratory. This report serves as the twelfth quarterly technical progress report for the SWC. Key activities for this reporting period focused on organizing and hosting three fall technology transfer meetings that will be held in Wyoming, Texas, and Pennsylvania. In addition, work has started on developing the 2004 SWC request-for-proposals which will be released during the next reporting period. During this reporting period, the efforts were focused primarily on the organizing the SWC fall technology transfer meetings.

  18. ESTABLISHMENT OF AN INDUSTRY-DRIVEN CONSORTIUM FOCUSED ON IMPROVING THE PRODUCTION PERFORMANCE OF DOMESTIC STRIPPER WELLS

    SciTech Connect

    Joel L. Morrison

    2004-12-23

    The Pennsylvania State University, under contract to the U.S. Department of Energy, National Energy Technology Laboratory will establish, promote, and manage a national industry-driven Stripper Well Consortium (SWC) that will be focused on improving the production performance of domestic petroleum and/or natural gas stripper wells. The consortium creates a partnership with the U.S. petroleum and natural gas industries and trade associations, state funding agencies, academia, and the National Energy Technology Laboratory. This report serves as the fifteenth quarterly technical progress report for the SWC. Key activities for this reporting period include: (1) hosting the SWC spring proposal meeting in Golden Colorado, (2) planning of the upcoming SWC fall technology transfer meetings, and (3) recruiting the SWC base membership.

  19. ESTABLISHMENT OF AN INDUSTRY-DRIVEN CONSORTIUM FOCUSED ON IMPROVING THE PRODUCTION PERFORMANCE OF DOMESTIC STRIPPER WELLS

    SciTech Connect

    Joel L. Morrison

    2005-02-17

    The Pennsylvania State University, under contract to the U.S. Department of Energy, National Energy Technology Laboratory will establish, promote, and manage a national industry-driven Stripper Well Consortium (SWC) that will be focused on improving the production performance of domestic petroleum and/or natural gas stripper wells. The consortium creates a partnership with the U.S. petroleum and natural gas industries and trade associations, state funding agencies, academia, and the National Energy Technology Laboratory. This report serves as the third quarterly technical progress report for the SWC. Key activities for this reporting period include: (1) host the State College, PA fall Technology Transfer meeting, (2) revision of the SWC By-laws, (3) the SWC Executive Council nomination and election for 2005-2006 term members, and (4) finalizing the plans for the Spring Proposal Meeting in San Antonio, Texas.

  20. ESTABLISHMENT OF AN INDUSTRY-DRIVEN CONSORTIUM FOCUSED ON IMPROVING THE PRODUCTION PERFORMANCE OF DOMESTIC STRIPPER WELLS

    SciTech Connect

    Joel L. Morrison

    2004-12-28

    The Pennsylvania State University, under contract to the U.S. Department of Energy, National Energy Technology Laboratory will establish, promote, and manage a national industry-driven Stripper Well Consortium (SWC) that will be focused on improving the production performance of domestic petroleum and/or natural gas stripper wells. The consortium creates a partnership with the U.S. petroleum and natural gas industries and trade associations, state funding agencies, academia, and the National Energy Technology Laboratory. This report serves as the first quarterly technical progress report for the SWC. Key activities for this reporting period include: (1) hosting the SWC spring proposal meeting in Golden Colorado, (2) planning of the upcoming SWC fall technology transfer meetings, and (3) recruiting the SWC base membership.

  1. Establishment of an Industry-Driven Consortium Focused on Improving the Production Performance of Domestic Stripper Wells

    SciTech Connect

    Joel L. Morrison; Sharon L. Elder

    2006-05-01

    The Pennsylvania State University, under contract to the U.S. Department of Energy (DOE), National Energy Technology Laboratory (NETL) established a national industry-driven Stripper Well Consortium (SWC) that is focused on improving the production performance of domestic petroleum and/or natural gas stripper wells. The consortium creates a partnership with the U.S. petroleum and natural gas industries and trade associations, state funding agencies, academia, and the National Energy Technology Laboratory. This report serves as the eighth quarterly technical progress report for the SWC. Key activities for this reporting period include: (1) Organize and host the 2006 Spring Meeting in State College, PA to review and select projects for SWC co-funding; (2) Participation in the 2006 PA CleanEnergy Expo Energy Theater to air the DVD on ''Independent Oil: Rediscovering American's Forgotten Wells''; (3) New member additions; (4) Improving communications; and (5) Planning of the fall technology meetings.

  2. Establishment of an Industry-Driven Consortium Focused on Improving the Production Performance of Domestic Stripper Wells

    SciTech Connect

    Joel L. Morrison; Sharon L. Elder

    2006-04-21

    The Pennsylvania State University, under contract to the U.S. Department of Energy (DOE), National Energy Technology Laboratory (NETL) has established a national industry-driven Stripper Well Consortium (SWC) that is focused on improving the production performance of domestic petroleum and/or natural gas stripper wells. The consortium creates a partnership with the U.S. petroleum and natural gas industries and trade associations, state funding agencies, academia, and the National Energy Technology Laboratory. This report serves as the seventh quarterly technical progress report for the SWC. Key activities for this reporting period include: (1) Nomination and election of the Executive Council members for the 2006-07 term, (2) Finalize and release the 2006 Request for Proposals (RFP), (3) Invoice and recruit members, (4) Plan for the spring meeting, (5) Improving communication efforts, and (6) Continue distribution of the DVD entitled: ''Independent Oil: Rediscovering American's Forgotten Wells''.

  3. Research proposal for development of an electron stripper using a thin liquid lithium film for rare isotope accelerator.

    SciTech Connect

    Momozaki, Y.; Nuclear Engineering Division

    2006-03-06

    Hydrodynamic instability phenomena in a thin liquid lithium film, which has been proposed for the first stripper in the driver linac of Rare Isotope Accelerator (RIA), were discussed. Since it was considered that film instability could significantly impair the feasibility of the liquid lithium film stripper concept, potential issues and research tasks in the RIA project due to these instability phenomena were raised. In order to investigate these instability phenomena, a research proposal plan was developed. In the theoretical part of this research proposal, a use of the linear stability theory was suggested. In the experimental part, it was pointed out that the concept of Reynolds number and Weber number scaling may allow conducting a preliminary experiment using inert simulants, hence reducing technical difficulty, complexity, and cost of the experiments. After confirming the thin film formation in the preliminary experiment using simulants, demonstration experiments using liquid lithium were proposed.

  4. Thermal Sensitive Foils in Physics Experiments

    ERIC Educational Resources Information Center

    Bochnícek, Zdenek; Konecný, Pavel

    2014-01-01

    The paper describes a set of physics demonstration experiments where thermal sensitive foils are used for the detection of the two dimensional distribution of temperature. The method is used for the demonstration of thermal conductivity, temperature change in adiabatic processes, distribution of electromagnetic radiation in a microwave oven and…

  5. Hydrogen and Palladium Foil: Two Classroom Demonstrations

    ERIC Educational Resources Information Center

    Klotz, Elsbeth; Mattson, Bruce

    2009-01-01

    In these two classroom demonstrations, students observe the reaction between H[subscript 2] gas and Pd foil. In the first demonstration, hydrogen and palladium combine within one minute at 1 atm and room temperature to yield the non-stoichiometric, interstitial hydride with formula close to the maximum known value, PdH[subscript 0.7]. In the…

  6. Foil Panel Mirrors for Nonimaging Applications

    NASA Technical Reports Server (NTRS)

    Kuyper, D. J.; Castillo, A. A.

    1984-01-01

    Large durable, lightweight mirrors made by bonding thick aluminum foil to honeycomb panels or other rigid, flat backings. Mirrors suitable for use as infrared shields, telescope doors, solar-furnance doors, advertising displays, or other reflectors that require low thermal emissivity and high specularity but do not require precise surface figure necessary for imaging.

  7. Indium Foil Serves As Thermally Conductive Gasket

    NASA Technical Reports Server (NTRS)

    Eastman, G. Yale; Dussinger, Peter M.

    1993-01-01

    Indium foil found useful as gasket to increase thermal conductance between bodies clamped together. Deforms to fill imperfections on mating surfaces. Used where maximum temperature in joint less than melting temperature of indium. Because of low melting temperature of indium, most useful in cryogenic applications.

  8. 6Li foil thermal neutron detector

    SciTech Connect

    Ianakiev, Kiril D; Swinhoe, Martyn T; Favalli, Andrea; Chung, Kiwhan; Macarthur, Duncan W

    2010-01-01

    In this paper we report on the design of a multilayer thermal neutron detector based on {sup 6}Li reactive foil and thin film plastic scintillators. The {sup 6}Li foils have about twice the intrinsic efficiency of {sup 10}B films and about four times higher light output due to a unique combination of high energy of reaction particles, low self absorption, and low ionization density of tritons. The design configuration provides for double sided readout of the lithium foil resulting in a doubling of the efficiency relative to a classical reactive film detector and generating a pulse height distribution with a valley between neutron and gamma signals similar to {sup 3}He tubes. The tens of microns thickness of plastic scintillator limits the energy deposited by gamma rays, which provides the necessary neutron/gamma discrimination. We used MCNPX to model a multilayer Li foil detector design and compared it with the standard HLNCC-II (18 {sup 3}He tubes operated at 4 atm). The preliminary results of the {sup 6}Li configuration show higher efficiency and one third of the die-away time. These properties, combined with the very short dead time of the plastic scintillator, offer the potential of a very high performance detector.

  9. Strong field electrodynamics of a thin foil

    SciTech Connect

    Bulanov, Sergei V.; Esirkepov, Timur Zh.; Kando, Masaki; Bulanov, Stepan S.; Rykovanov, Sergey G.; Pegoraro, Francesco

    2013-12-15

    Exact solutions describing the nonlinear electrodynamics of a thin double layer foil are presented. These solutions correspond to a broad range of problems of interest for the interaction of high intensity laser pulses with overdense plasmas, such as frequency upshifting, high order harmonic generation, and high energy ion acceleration.

  10. The Fluid Foil: The Seventh Simple Machine

    ERIC Educational Resources Information Center

    Mitts, Charles R.

    2012-01-01

    A simple machine does one of two things: create a mechanical advantage (lever) or change the direction of an applied force (pulley). Fluid foils are unique among simple machines because they not only change the direction of an applied force (wheel and axle); they convert fluid energy into mechanical energy (wind and Kaplan turbines) or vice versa,…

  11. Single crystalline graphene synthesized by thermal annealing of humic acid over copper foils

    NASA Astrophysics Data System (ADS)

    Beall, Gary W.; Duraia, El-Shazly M.; Yu, Q.; Liu, Z.

    2014-02-01

    Production of graphene by thermal annealing on copper foil substrates has been studied with different sources of carbon. The three carbon sources include humic acid derived from leonardite, graphenol, and activated charcoal. Hexagonal single crystalline graphene has been synthesized over the copper foil substrates by thermal annealing of humic acid, derived from leonardite, in argon and hydrogen atmosphere (Ar/H2=20). The annealing temperature was varied between 1050 °C and 1100 °C at atmospheric pressure. Samples have been investigated using scanning electron microscope (SEM) and Raman spectroscopy. At lower temperatures the thermal annealing of the three carbon sources used in this study produces pristine graphene nanosheets which cover almost the whole substrate. However when the annealing temperature has been increased up to 1100 °C, hexagonal single crystalline graphene have been observed only in the case of the humic acid. Raman analysis showed the existence of 2D band around 2690 cm-1.

  12. Spot size dependence of laser accelerated protons in thin multi-ion foils

    SciTech Connect

    Liu, Tung-Chang Shao, Xi; Liu, Chuan-Sheng; Eliasson, Bengt; Wang, Jyhpyng; Chen, Shih-Hung

    2014-06-15

    We present a numerical study of the effect of the laser spot size of a circularly polarized laser beam on the energy of quasi-monoenergetic protons in laser proton acceleration using a thin carbon-hydrogen foil. The used proton acceleration scheme is a combination of laser radiation pressure and shielded Coulomb repulsion due to the carbon ions. We observe that the spot size plays a crucial role in determining the net charge of the electron-shielded carbon ion foil and consequently the efficiency of proton acceleration. Using a laser pulse with fixed input energy and pulse length impinging on a carbon-hydrogen foil, a laser beam with smaller spot sizes can generate higher energy but fewer quasi-monoenergetic protons. We studied the scaling of the proton energy with respect to the laser spot size and obtained an optimal spot size for maximum proton energy flux. Using the optimal spot size, we can generate an 80 MeV quasi-monoenergetic proton beam containing more than 10{sup 8} protons using a laser beam with power 250 TW and energy 10 J and a target of thickness 0.15 wavelength and 49 critical density made of 90% carbon and 10% hydrogen.

  13. ESTABLISHMENT OF AN INDUSTRY-DRIVEN CONSORTIUM FOCUSED ON IMPROVING THE PRODUCTION PERFORMANCE OF DOMESTIC STRIPPER WELLS

    SciTech Connect

    Joel L. Morrison

    2001-09-12

    The Pennsylvania State University, under contract to the US Department of Energy, National Energy Technology Laboratory will establish, promote, and manage a national industry-driven Stripper Well Consortium (SWC) that will be focused on improving the production performance of domestic petroleum and/or natural gas stripper wells. the consortium creates a partnership with the US petroleum and natural gas industries and trade associations, state funding agencies, academia, and the National Energy Technology Laboratory. This report serves as the third quarterly technical progress report for the SWC. During this reporting period the SWC entered into a co-funding arrangement with the New York State Energy Development Authority (NYSERDA) to provide an additional $100,000 in co-funding for stripper well production-orientated projects.The SWC hosted its first meeting in which members proposed research projects to the SWC membership. The meeting was held on April 9-10, 2001 in State College, Pennsylvania. Twenty three proposals were submitted to the SWC for funding consideration. Investigators of the proposed projects provided the SWC membership with a 20 minute (15 minute technical discussion, 5 minute question and answer session) presentation. Of the 23 proposals, the Executive Council approved $921,000 in funding for 13 projects. Penn State then immediately started the process of issuing subcontracts to the various projects approved for funding.

  14. Performance and lifetime of solar mirror foils in space

    SciTech Connect

    Fink, D.; Biersack, J.P.; Staedele, M.

    1985-01-01

    The results of a Monte Carlo computer analysis of the long term effects of space radiation on the surfaces of giant orbiting mirrors are presented. The mirrors, thin surfaced and made of substances like, e.g., Mylar and Hostephan, which are polymers, would reflect solar radiation to earth and be of a size equivalent to that of the area they would illumine. Possible applications are the warming of cities, melting of icebergs in shipping lanes and the illumination of solar power plants. Attention was focused on the changes produced in the reflective surface by solar wind particle bombardment. It was found that an Al covering at least 0.1 mm thick would be needed for protection. Nevertheless, the surface would be destroyed by blistering and foil carbonization within 10 yr and would then require replacement. 12 references.

  15. Optical and electrical performance of commercially manufactured large GEM foils

    NASA Astrophysics Data System (ADS)

    Posik, M.; Surrow, B.

    2015-12-01

    With interest in large area GEM foils increasing and CERN being the only main distributor, keeping up with the demand for GEM foils will be difficult. Thus the commercialization of GEMs is being established by Tech-Etch of Plymouth, MA, USA using single-mask techniques. We report here on the first of a two step quality verification of the commercially produced 10×10 cm2 and 40×40 cm2 GEM foils, which includes characterizing their electrical and geometrical properties. We have found that the Tech-Etch foils display excellent electrical properties, as well as uniform and consistent hole diameters comparable to established foils produced by CERN.

  16. Nuclear target foil fabrication for the Romano Event

    SciTech Connect

    Weed, J.W.; Romo, J.G. Jr.; Griggs, G.E.

    1984-06-19

    The Vacuum Processes Lab, of LLNL's M.E. Dept. - Material Fabrication Division, was requested to provide 250 coated Parylene target foils for a nuclear physics experiment titled the ROMANO Event. Due to the developmental nature of some of the fabrication procedures, approximately 400 coated foils were produced to satisfy the event's needs. The foils were used in the experiment as subkilovolt x-ray, narrow band pass filters, and wide band ultraviolet filters. This paper is divided into three sections describing: (1) nuclear target foil fabrication, (2) Parylene substrate preparation and production, and (3) foil and substrate inspections.

  17. Porn star/stripper/escort: economic and sexual dynamics in a sex work career.

    PubMed

    Escoffier, Jeffrey

    2007-01-01

    This article explores the career dynamics of performers in the gay male pornography industry, by focusing on a common career path- from porn star to stripper to escort. Between 1995 and 2005, most men performing in gay porn films, unlike contract actresses in the straight porn industry, have been unable to earn enough income to work exclusively as performers in front of the camera. The industry's constant search for new faces and fresh performers creates what sociologist Paul Cressey has called "the retrogressive dynamic": The longer a person works in a sexual occupation, the less one is paid, and the lower the status of the work venue. In the porn industry, one aspect of this process is referred to as "overexposure," during which the performer experiences a diminishing "fantasy potential" as fans lose erotic interest in the porn star who has appeared too frequently in too many movies. Performers attempt to confront the retrogressive dynamic by limiting the number of adult films in which they appear in a year, diversifying their sexual repertoire, or shifting into other roles within the industry (behind the camera, marketing, production, etc.). One common option is to pursue work in economically complementary forms of sex work such as stripping and escorting. PMID:18019074

  18. Development of a liquid lithium thin film for use as a heavy ion beam stripper

    NASA Astrophysics Data System (ADS)

    Momozaki, Y.; Nolen, J.; Reed, C.; Novick, V.; Specht, J.

    2009-04-01

    A series of experiments was performed to investigate the feasibility of a liquid lithium thin film for a charge stripper in a high-power heavy ion linac. Various preliminary experiments using simulants were first conducted to determine the film formation scheme, to investigate the film stability, and to obtain the design parameters for a liquid lithium thin film system. Based on the results from these preliminary studies, a prototypical, high pressure liquid lithium system was constructed to demonstrate liquid lithium thin film formation. This system was capable of driving liquid lithium at lesssim300 °C and up to 13.9 MPa (2000 psig) through a nozzle opening as large as 1 mm (40 mil) in diameter. This drive pressure corresponds to a Li velocity of >200 m/s. A thin lithium film of 9 mm in width at velocity of ~58 m/s was produced. Its thickness was estimated to be roughly lesssim13 μm. High vacuum was maintained in the area of the film. This type of liquid metal thin film may also be used in other high power beam applications such as for intense X-ray or neutron sources.

  19. Biodegradation of paint stripper solvents in a modified gas lift loop bioreactor

    SciTech Connect

    Vanderberg-Twary, L.; Steenhoudt, K.; Travis, B.J.; Hanners, J.L.; Foreman, T.M.; Brainard, J.R.

    1997-07-05

    Paint stripping wastes generated during the decontamination and decommissioning of former nuclear facilities contain paint stripping organics (dichloromethane, 2-propanol, and methanol) and bulk materials containing paint pigments. It is desirable to degrade the organic residues as part of an integrated chemical-biological treatment system. The authors have developed a modified gas lift loop bioreactor employing a defined consortium of Thodococcus rhodochrous strain OFS and Hyphomicrobium sp. DM-2 that degrades paint stripper organics. Mass transfer coefficients and kinetic constants for biodegradation in the system were determined. It was found that transfer of organic substrates from surrogate waste into the air and further into the liquid medium in the bioreactor were rapid processes, occurring within minutes. Monod kinetics was employed to model the biodegradation of paint stripping organics. Analysis of the bioreactor process was accomplished with BIOLAB, a mathematical code that simulates coupled mass transfer and biodegradation processes. This code was used to fit experimental data to monod kinetics and to determine kinetic parameters. The BIOLAB code was also employed to compare activities in the bioreactor of individual microbial cultures to the activities of combined cultures in the bioreactor. This code is of benefit for further optimization and scale-up of the bioreactor for treatment of paint stripping and other volatile organic wastes in bulk materials.

  20. SUCCESSFUL IMPLEMENTATION OF THE LOW MAINTENANCE AIRLIFT PUMP TO EXTEND THE LIFE OF STRIPPER WELLS

    SciTech Connect

    Adam Bennett

    2004-03-01

    This report summarizes the evolution and testing results of the Airlift pumping system. System development has passed through four versions: Gen 1, Gen 2, Gen 3, and 3.1. The DOE grant only funded the development and testing of the Gen 2 version, but the Gen 2 unit was a crucial design bridge between the primitive Gen 1 unit and the sophisticated Gen 3 unit. The DOE grant covered the years 2000 to 2002, but this report analyzes the data collected from testing on all four versions across the years 1998 through 2003. A variety of Airlift units were tested in twelve wells. The overall reliability of the Airlift versus traditional pump jack technology was compared. Although neither the Gen 2 nor Gen 3 demonstrated a reliable pumping system, the Gen 3.1 was designed to correct the flaws in these systems. Currently undergoing testing, the Gen 3.1 is operating with a reliability four times better and two-and-a-half times better in the time it requires to repair than standard pump jack technology. The high reliability and low maintenance required to operate the Airlift Gen 3.1 will make the Airlift the natural and economical choice to replace pump jacks on stripper wells.

  1. Impact of GEM foil hole geometry on GEM detector gain

    NASA Astrophysics Data System (ADS)

    Karadzhinova, A.; Nolvi, A.; Veenhof, R.; Tuominen, E.; Hæggström, E.; Kassamakov, I.

    2015-12-01

    Detailed 3D imaging of Gas Electron Multiplier (GEM) foil hole geometry was realized. Scanning White Light Interferometry was used to examine six topological parameters of GEM foil holes from both sides of the foil. To study the effect of the hole geometry on detector gain, the ANSYS and Garfield ++ software were employed to simulate the GEM detector gain on the basis of SWLI data. In particular, the effective gain in a GEM foil with equally shaped holes was studied. The real GEM foil holes exhibited a 4% lower effective gain and 6% more electrons produced near the exit electrode of the GEM foil than the design anticipated. Our results indicate that the GEM foil hole geometry affects the gain performance of GEM detectors.

  2. Composite metal foil and ceramic fabric materials

    DOEpatents

    Webb, B.J.; Antoniak, Z.I.; Prater, J.T.; DeSteese, J.G.

    1992-03-24

    The invention comprises new materials useful in a wide variety of terrestrial and space applications. In one aspect, the invention comprises a flexible cloth-like material comprising a layer of flexible woven ceramic fabric bonded with a layer of metallic foil. In another aspect, the invention includes a flexible fluid impermeable barrier comprising a flexible woven ceramic fabric layer having metal wire woven therein. A metallic foil layer is incontinuously welded to the woven metal wire. In yet another aspect, the invention includes a material comprising a layer of flexible woven ceramic fabric bonded with a layer of an organic polymer. In still another aspect, the invention includes a rigid fabric structure comprising a flexible woven ceramic fabric and a resinous support material which has been hardened as the direct result of exposure to ultraviolet light. Inventive methods for producing such material are also disclosed. 11 figs.

  3. Composite metal foil and ceramic fabric materials

    DOEpatents

    Webb, Brent J.; Antoniak, Zen I.; Prater, John T.; DeSteese, John G.

    1992-01-01

    The invention comprises new materials useful in a wide variety of terrestrial and space applications. In one aspect, the invention comprises a flexible cloth-like material comprising a layer of flexible woven ceramic fabric bonded with a layer of metallic foil. In another aspect, the invention includes a flexible fluid impermeable barrier comprising a flexible woven ceramic fabric layer having metal wire woven therein. A metallic foil layer is incontinuously welded to the woven metal wire. In yet another aspect, the invention includes a material comprising a layer of flexible woven ceramic fabric bonded with a layer of an organic polymer. In still another aspect, the invention includes a rigid fabric structure comprising a flexible woven ceramic fabric and a resinous support material which has been hardened as the direct result of exposure to ultraviolet light. Inventive methods for producing such material are also disclosed.

  4. FoilSim: Basic Aerodynamics Software Created

    NASA Technical Reports Server (NTRS)

    Peterson, Ruth A.

    1999-01-01

    FoilSim is interactive software that simulates the airflow around various shapes of airfoils. The graphical user interface, which looks more like a video game than a learning tool, captures and holds the students interest. The software is a product of NASA Lewis Research Center s Learning Technologies Project, an educational outreach initiative within the High Performance Computing and Communications Program (HPCCP).This airfoil view panel is a simulated view of a wing being tested in a wind tunnel. As students create new wing shapes by moving slider controls that change parameters, the software calculates their lift. FoilSim also displays plots of pressure or airspeed above and below the airfoil surface.

  5. Optofluidic dye laser in a foil.

    PubMed

    Vannahme, Christoph; Christiansen, Mads Brøkner; Mappes, Timo; Kristensen, Anders

    2010-04-26

    First order distributed feedback optofluidic dye lasers embedded in a 350 microm thick TOPAS((R)) foil are demonstrated. They are designed in order to give high output pulse energies. Microfluidic channels and first order distributed feedback gratings are fabricated in parallel by thermal nanoimprint into a 100 microm foil. The channels are closed by thermal bonding with a 250 microm thick foil and filled with 5.10(-3) mol/l Pyrromethene 597 in benzyl alcohol. The fluid forms a liquid core single mode slab waveguide of 1.6 microm height on a nanostructured grating area of 0.5 x 0.5 mm(2). This results in a large gain volume. Two grating periods of 185 nm and 190 nm yield single mode laser light emission at 566 nm and 581 nm respectively. High emitted pulse energies of more than 1 microJ are reported. Stable operation for more than 25 min at 10 Hz pulse repetition rate is achieved. PMID:20588775

  6. Brazing Inconel 625 Using the Copper Foil

    NASA Astrophysics Data System (ADS)

    Chen, Wen-Shiang; Wang, Cheng-Yen; Shiue, Ren-Kae

    2013-12-01

    Brazing Inconel 625 (IN-625) using the copper foil has been investigated in this research. The brazed joint is composed of nanosized CrNi3 precipitates and Cr/Mo/Nb/Ni quaternary compound in the Cu/Ni-rich matrix. The copper filler 50 μm in thickness is enough for the joint filling. However, the application of Cu foil 100 μm in thickness has little effect on the shear strength of the brazed joint. The specimen brazed at 1433 K (1160 °C) for 1800 seconds demonstrates the best shear strength of 470 MPa, and its fractograph is dominated by ductile dimple fracture with sliding marks. Decreasing the brazing temperature slightly decreases the shear strength of the brazed joint due to the presence of a few isolated solidification shrinkage voids smaller than 15 μm. Increasing the brazing temperature, especially for the specimen brazed at 1473 K (1200 °C), significantly deteriorates the shear strength of the joint below 260 MPa because of coalescence of isothermal solidification shrinkage voids in the joint. The Cu foil demonstrates potential in brazing IN-625 for industrial application.

  7. Microstructural Features in Aged Erbium Tritide Foils

    SciTech Connect

    Gelles, David S.; Brewer, L. N.; Kotula, Paul G.; Cowgill, Donald F.; Busick, C. C.; Snow, C. S.

    2008-01-01

    Aged erbium tritide foil specimens are found to contain five distinctly different microstructural features. The general structure was of large columnar grains of ErT2. But on a fine scale, precipitates believed to be erbium oxy-tritides and helium bubbles could be identified. The precipitate size was in the range of ~10 nm and the bubbles were of an unusual planar shape on {111} planes with an invariant thickness of ~1 nm and a diameter on the order of 10 nm. Also, an outer layer containing no fine precipitate structure and only a few helium bubbles was present on foils. This layer is best described as a denuded zone which probably grew during aging in air. Finally, large embedded Er2O3 particles were found at low density and non-uniformly distributed, but sometimes extending through the thickness of the foil. A failure mechanism allowing the helium to escape is suggested by observed cracking between bubbles closer to end of life.

  8. Optical quality assurance of GEM foils

    NASA Astrophysics Data System (ADS)

    Hildén, T.; Brücken, E.; Heino, J.; Kalliokoski, M.; Karadzhinova, A.; Lauhakangas, R.; Tuominen, E.; Turpeinen, R.

    2015-01-01

    An analysis software was developed for the high aspect ratio optical scanning system in the Detector Laboratory of the University of Helsinki and the Helsinki Institute of Physics. The system is used e.g. in the quality assurance of the GEM-TPC detectors being developed for the beam diagnostics system of the SuperFRS at future FAIR facility. The software was tested by analyzing five CERN standard GEM foils scanned with the optical scanning system. The measurement uncertainty of the diameter of the GEM holes and the pitch of the hole pattern was found to be 0.5 μm and 0.3 μm, respectively. The software design and the performance are discussed. The correlation between the GEM hole size distribution and the corresponding gain variation was studied by comparing them against a detailed gain mapping of a foil and a set of six lower precision control measurements. It can be seen that a qualitative estimation of the behavior of the local variation in gain across the GEM foil can be made based on the measured sizes of the outer and inner holes.

  9. Li insertion/extraction reaction at a Si film evaporated on a Ni foil

    NASA Astrophysics Data System (ADS)

    Ohara, Shigeki; Suzuki, Junji; Sekine, Kyoichi; Takamura, Tsutomu

    In an attempt to provide a Si material having a long cycle life as an anode of Li-ion batteries, we prepared a metallic Si film on a Ni foil by a vacuum evaporation method. Due to the presence of a naturally formed compact passivation film on the Ni foil, a homogeneous, compact amorphous-like Si film strongly adhering to the Ni substrate could be obtained very easily. The Si film thus obtained on a Ni foil was evaluated electrochemically with cyclic voltammetry (CV) and constant current charge/discharge cycle test (CT) in two types of solvents containing 1 M LiClO 4, i.e. propylene carbonate (PC), and a 1:1 (v/v) mixture of ethylene carbonate (EC) and dimethyl carbonate (DMC). Two strong peaks were observed on the anodic branch of the CV at 300 mV (versus Li/Li +) and 500 mV and the constant current discharge curve of CT produced a wide plateau at around 400 mV in EC/DMC with a discharge capacity of 1700-2200 mAh/g at a discharge rate of 2 C. Nearly the same performance was observed as well in PC, where no solvent decomposition was detected. The capacity depended on the preparation conditions and the film thickness. The cycleability at 2 C charge/discharge rate was over 750 cycles. One of the important issues to solve is to reduce the large initial charge loss.

  10. Correlation between carbon activity and carbon content in α-iron in liquid sodium negative electrode of liquid metal battery

    NASA Astrophysics Data System (ADS)

    Shin, Sang Hun; Lee, Jeong Hyeon; Lee, Jung Ki; Kim, Ji Hyun

    2015-11-01

    Non-metallic elements such as carbon, oxygen, and nitrogen in liquid sodium exert a significant effect on the material behaviour of cell construction materials in liquid metal battery systems. Austenitic Fe-18%Cr-8%Ni foil and α-iron foil are equilibrated at 550 °C in sodium, and, subsequently, the concentration of carbon in the foils is analysed. A new relationship has been obtained between carbon activity and carbon concentration in α-iron foil, and is compared with the previously developed ones involving 304 SS foil reference samples. An equilibrium method has been developed to measure the activity of carbon in liquid sodium by using α-iron with this new expression. The results show similar values to those obtained with the 304 SS foil reference samples.

  11. ESTABLISHMENT OF AN INDUSTRY-DRIVEN CONSORTIUM FOCUSED ON IMPROVING THE PRODUCTION PERFORMANCE OF DOMESTIC STRIPPER WELLS

    SciTech Connect

    Joel L. Morrison

    2002-09-30

    The Pennsylvania State University, under contract to the U.S. Department of Energy (DOE), National Energy Technology Laboratory (NETL), has established a national industry-driven Stripper Well Consortium (SWC) that is focused on improving the production performance of domestic petroleum and/or natural gas stripper wells. The consortium creates a partnership with the U.S. petroleum and natural gas industries and trade associations, state funding agencies, academia, and the National Energy Technology Laboratory. This report serves as the second topical report. The SWC has grown and diversified its membership during its first 24 months of existence. The Consortium is now focused on building strategic alliances with additional industrial, state, and federal entities to expand further the SWC membership base and transfer technologies as they are developed. In addition, the Consortium has successfully worked to attract state support to co-fund SWC projects. Penn State has entered a co-funding arrangement with the New York State Energy Development Authority (NYSERDA) which has provided $200,000 over the last two years to co-fund stripper well production-orientated projects that have relevance to New York state producers. During this reporting period, the Executive Council approved co-funding for 14 projects that have a total project value of $2,116,897. Since its inception, the SWC has approved cofunding for 27 projects that have a total project value of $3,632,109.84. The SWC has provided $2,242,701 in co-funding for these projects and programmatically maintains a cost share of 39%.

  12. Large-scale high-efficiency air stripper and recovery well network for removing volatile organic chlorocarbons from ground water

    SciTech Connect

    Boone, L F; Lorfenz, R; Muska, C F; Steele, J L

    1986-05-01

    The Savannah River Plant (SRP) produces special nuclear materials for the US Government. Since 1958, chemical wastes generated by an aluminum forming/metal finishing process used to manufacture fuel and target assemblies were discharged to a settling basin. This process waste stream contained acids, alkalis, metals, and chlorinated degreasing solvents. In 1981, these solvents, specifically trichloroethylene and tetrachloroethylene, were discovered in monitor wells near the settling basin. A monitor well network was installed to define the vertical and horizontal extent of the plume. The current inventory of total chlorocarbons in the saturated zone is approximately 360,000 pounds within the 100 ppB contour interval. During 1983, air stripping technology was evaluated to remove these solvents from the ground water. A 20-gpm ground water pilot air stripper with one recovery well was tested. Performance data from this unit were then used to design a 50-gpm production prototype air stripper. This unit demonstrated that degreaser solvent concentrations in ground water could be reduced from 120,000 ppB to less than the detection limit of 1 ppB. Data from these two units were then used to design an air stripper column that would process contaminated ground water at a rate of 400 gpm. Water is fed to this column from a network of 11 recovery wells. These wells were located in the zone of contamination, as defined by analytical and numerical modeling techniques. This system has been operational since April 1985. To date, over 65,000 pounds of chlorinated degreaser solvents have been removed from an underlying aquifer. The effects of this program on the hydraulic gradient and contamination movement are currently being evaluated. The purpose of this paper is to describe the ground water remediation program at the Savannah River Plant.

  13. The Effect of Journal Roughness and Foil Coatings on the Performance of Heavily Loaded Foil Air Bearings

    NASA Technical Reports Server (NTRS)

    Radil, Kevin C.; DellaCorte, Christopher

    2001-01-01

    Foil air bearing load capacity tests were conducted to investigate if a solid lubricant coating applied to the surface of the bearing's top foil can function as a break-in coating. Two foil coating materials, a conventional soft polymer film (polyimide) and a hard ceramic (alumina), were independently evaluated against as-ground and worn (run-in) journals coated with NASA PS304, a high-temperature solid lubricant composite coating. The foil coatings were evaluated at journal rotational speeds of 30,000 rpm and at 25 C. Tests were also performed on a foil bearing with a bare (uncoated) nickel-based superalloy top foil to establish a baseline for comparison. The test results indicate that the presence of a top foil solid lubricant coating is effective at increasing the load capacity performance of the foil bearing. Compared to the uncoated baseline, the addition of the soft polymer coating on the top foil increased the bearing load coefficient by 120% when operating against an as-ground journal surface and 85 percent against a run-in journal surface. The alumina coating increased the load coefficient by 40% against the as-ground journal but did not have any affect when the bearing was operated with the run-in journal. The results suggest that the addition of solid lubricant films provide added lubrication when the air film is marginal indicating that as the load capacity is approached foil air bearings transition from hydrodynamic to mixed and boundary lubrication.

  14. Effects of Aluminum Foil Packaging on Elemental Analysis of Bone.

    PubMed

    Lewis, Lyniece; Christensen, Angi M

    2016-03-01

    Burned skeletal material is often very fragile and at high risk for fragmentation during packaging and transportation. One method that has been suggested to protect bones in these cases is to carefully wrap them in aluminum foil. Traces of aluminum, however, are known to transfer from foil packaging materials to food products. If such transfer occurs between aluminum foil and bones, it could interfere with subsequent chemical, elemental and isotopic analyses, which are becoming more common in forensic anthropological investigations. This study examined aluminum levels in bones prior to and following the use of aluminum foil packaging and storage for a 6-week period. Results indicate no significant change in the detected levels of aluminum (p > 0.05), even when packaged in compromised foil and exposed to elevated temperatures. Aluminum foil can therefore continue to be recommended as a packaging medium without affecting subsequent chemical examinations. PMID:27404616

  15. Microfabricated Segmented-Involute-Foil Regenerator for Stirling Engines

    NASA Technical Reports Server (NTRS)

    Ibrahim, Mounir; Danila, Daniel; Simon, Terrence; Mantell, Susan; Sun, Liyong; Gedeon, David; Qiu, Songgang; Wood, Gary; Kelly, Kevin; McLean, Jeffrey

    2010-01-01

    An involute-foil regenerator was designed, microfabricated, and tested in an oscillating-flow test rig. The concept consists of stacked involute-foil nickel disks (see figure) microfabricated via a lithographic process. Test results yielded a performance of about twice that of the 90-percent random-fiber currently used in small Stirling converters. The segmented nature of the involute- foil in both the axial and radial directions increases the strength of the structure relative to wrapped foils. In addition, relative to random-fiber regenerators, the involute-foil has a reduced pressure drop, and is expected to be less susceptible to the release of metal fragments into the working space, thus increasing reliability. The prototype nickel involute-foil regenerator was adequate for testing in an engine with a 650 C hot-end temperature. This is lower than that required by larger engines, and high-temperature alloys are not suited for the lithographic microfabrication approach.

  16. Method of forming a thin unbacked metal foil

    DOEpatents

    Duchane, David V.; Barthell, Barry L.

    1984-01-01

    In a method of forming a thin (<2 .mu.m) unbacked metal foil having a desired curviplanar shape, a soluble polymeric film, preferably comprising polyvinyl alcohol, is formed on a supporting structure having a shape that defines the desired shape of the foil product. A layer of metal foil is deposited onto one side of the soluble film, preferably by vacuum vapor deposition. The metallized film is then immersed in a suitable solvent to dissolve the film and thereby leave the metal foil as an unbacked metal foil element mounted on the supporting structure. Aluminum foils less than 0.2 .mu.m (2,000 .ANG.) thick and having an areal density of less than 54 .mu.g/cm.sup.2 have been obtained.

  17. Magnetohydrodynamic modelling of exploding foil initiators

    NASA Astrophysics Data System (ADS)

    Neal, William

    2015-06-01

    Magnetohydrodynamic (MHD) codes are currently being developed, and used, to predict the behaviour of electrically-driven flyer-plates. These codes are of particular interest to the design of exploding foil initiator (EFI) detonators but there is a distinct lack of comparison with high-fidelity experimental data. This study aims to compare a MHD code with a collection of temporally and spatially resolved diagnostics including PDV, dual-axis imaging and streak imaging. The results show the code's excellent representation of the flyer-plate launch and highlight features within the experiment that the model fails to capture.

  18. Apparatus and process for ultrasonic seam welding stainless steel foils

    DOEpatents

    Leigh, Richard W.

    1992-01-01

    An ultrasonic seam welding apparatus having a head which is rotated to form contact, preferably rolling contact, between a metallurgically inert coated surface of the head and an outside foil of a plurality of layered foils or work materials. The head is vibrated at an ultrasonic frequency, preferably along a longitudinal axis of the head. The head is constructed to transmit vibration through a contacting surface of the head into each of the layered foils. The contacting surface of the head is preferably coated with aluminum oxide to prevent the head from becoming welded to layered stainless steel foils.

  19. [Foil bandages--a modern method of covering wounds].

    PubMed

    Sedlarik, K M; Hájek, M

    1994-04-01

    Single-layer foil bandages which belong to the group of so-called occlusive bandaging materials were originally developed from incision foils. Due to their semipermeability theses bandages permit only restricted evaporation of water from the wound and thus maintain its surface constantly slightly wet. They can be used for longer periods and are thus more economical. Although foil bandages are suitable only for some types of wounds, they have great advantages. Wounds dressed with these foil bandages can be easily and frequently checked and offer wounds excellent antimicrobial protection. PMID:8085186

  20. Characterization of U-Mo Foils for AFIP-7

    SciTech Connect

    Edwards, Danny J.; Ermi, Ruby M.; Schemer-Kohrn, Alan L.; Overman, Nicole R.; Henager, Charles H.; Burkes, Douglas; Senor, David J.

    2012-11-07

    Twelve AFIP in-process foil samples, fabricated by either Y-12 or LANL, were shipped from LANL to PNNL for potential characterization using optical and scanning electron microscopy techniques. Of these twelve, nine different conditions were examined to one degree or another using both techniques. For this report a complete description of the results are provided for one archive foil from each source of material, and one unirradiated piece of a foil of each source that was irradiated in the Advanced Test Reactor. Additional data from two other LANL conditions are summarized in very brief form in an appendix. The characterization revealed that all four characterized conditions contained a cold worked microstructure to different degrees. The Y-12 foils exhibited a higher degree of cold working compared to the LANL foils, as evidenced by the highly elongated and obscure U-Mo grain structure present in each foil. The longitudinal orientations for both of the Y-12 foils possesses a highly laminar appearance with such a distorted grain structure that it was very difficult to even offer a range of grain sizes. The U-Mo grain structure of the LANL foils, by comparison, consisted of a more easily discernible grain structure with a mix of equiaxed and elongated grains. Both materials have an inhomogenous grain structure in that all of the characterized foils possess abnormally coarse grains.

  1. Methods of making metallic glass foil laminate composites

    DOEpatents

    Vianco, Paul T.; Fisher, Robert W.; Hosking, Floyd M.; Zanner, Frank J.

    1996-01-01

    A process for the fabrication of a rapidly solidified foil laminate composite. An amorphous metallic glass foil is flux treated and coated with solder. Before solidification of the solder the foil is collected on a take-up spool which forms the composite into a solid annular configuration. The resulting composite exhibits high strength, resiliency and favorable magnetic and electrical properties associated with amorphous materials. The composite also exhibits bonding strength between the foil layers which significantly exceeds the bulk strength of the solder alone.

  2. Methods of making metallic glass foil laminate composites

    DOEpatents

    Vianco, P.T.; Fisher, R.W.; Hosking, F.M.; Zanner, F.J.

    1996-08-20

    A process for the fabrication of a rapidly solidified foil laminate composite. An amorphous metallic glass foil is flux treated and coated with solder. Before solidification of the solder the foil is collected on a take-up spool which forms the composite into a solid annular configuration. The resulting composite exhibits high strength, resiliency and favorable magnetic and electrical properties associated with amorphous materials. The composite also exhibits bonding strength between the foil layers which significantly exceeds the bulk strength of the solder alone. 6 figs.

  3. Ti foil light in the ATA (Advanced Test Accelerator) beam

    SciTech Connect

    Slaughter, D.R.; Chong, Y.P.; Goosman, D.R.; Rule, D.W.; Fiorito, R.B.

    1987-09-01

    An experiment is in progress to characterize the visible light produced when a Ti foil is immersed in the ATA 2 kA, 43 MeV beam. Results obtained to date indicate that the optical condition of the foil surface is a critical determinant of these characteristics, with a very narrow angular distribution obtained when a highly polished and flat foil is used. These data are consistent with the present hypothesis that the light is produced by transition radiation. Incomplete experiments to determine the foil angle dependence of the detected light and its polarization are summarized and remaining experiments are described.

  4. Silicon oxide permeation barrier coating of PET bottles and foils

    NASA Astrophysics Data System (ADS)

    Steves, Simon; Deilmann, Michael; Awakowicz, Peter

    2009-10-01

    Modern packaging materials such as polyethylene terephthalate (PET) have displaced established materials in many areas of food and beverage packaging. Plastic packing materials offer are various advantages concerning production and handling. PET bottles for instance are non-breakable and lightweight compared to glass and metal containers. However, PET offers poor barrier properties against gas permeation. Therefore, the shelf live of packaged food is reduced. Permeation of gases can be reduced by depositing transparent plasma polymerized silicon oxide (SiOx) barrier coatings. A microwave (2.45 GHz) driven low pressure plasma reactor is developed based on a modified Plasmaline antenna to treat PET foils or bottles. To increase the barrier properties of the coatings furthermore a RF substrate bias (13.56 MHz) is applied. The composition of the coatings is analyzed by means of Fourier transform infrared (FTIR) spectroscopy regarding carbon and hydrogen content. Influence of gas phase composition and substrate bias on chemical composition of the coatings is discussed. A strong relation between barrier properties and film composition is found: good oxygen barriers are observed as carbon content is reduced and films become quartz-like. Regarding oxygen permeation a barrier improvement factor (BIF) of 70 is achieved.

  5. Method of making porous conductive supports for electrodes. [by electroforming and stacking nickel foils

    NASA Technical Reports Server (NTRS)

    Schaer, G. R. (Inventor)

    1973-01-01

    Porous conductive supports for electrochemical cell electrodes are made by electroforming thin corrugated nickel foil, and by stacking pieces of the corrugated foil alternatively with pieces of thin flat nickel foil. Corrugations in successive corrugated pieces are oriented at different angles. Adjacent pieces of foil are bonded by heating in a hydrogen atmosphere and then cutting the stack in planes perpendicular to the foils.

  6. Actinide Foil Production for MPACT Research

    SciTech Connect

    Beller, Denis

    2012-10-30

    Sensitive fast-neutron detectors are required for use in lead slowing down spectrometry (LSDS), an active interrogation technique for used nuclear fuel assay for Materials Protection, Accounting, and Controls Technologies (MPACT). During the past several years UNLV sponsored a research project at RPI to investigate LSDS; began development of fission chamber detectors for use in LSDS experiments in collaboration with INL, LANL, and Oregon State U.; and participated in a LSDS experiment at LANL. In the LSDS technique, research has demonstrated that these fission chamber detectors must be sensitive to fission energy neutrons but insensitive to thermal-energy neutrons. Because most systems are highly sensitive to large thermal neutron populations due to the well-known large thermal cross section of 235U, even a miniscule amount of this isotope in a fission chamber will overwhelm the small population of higher-energy neutrons. Thus, fast-fission chamber detectors must be fabricated with highly depleted uranium (DU) or ultra-pure thorium (Th), which is about half as efficient as DU. Previous research conducted at RPI demonstrated that the required purity of DU for assay of used nuclear fuel using LSDS is less than 4 ppm 235U, material that until recently was not available in the U.S. In 2009 the PI purchased 3 grams of ultra-depleted uranium (uDU, 99.99998% 238U with just 0.2 ± 0.1 ppm 235U) from VNIIEF in Sarov, Russia. We received the material in the form of U3O8 powder in August of 2009, and verified its purity and depletion in a FY10 MPACT collaboration project. In addition, chemical processing for use in FC R&D was initiated, fission chamber detectors and a scanning alpha-particle spectrometer were developed, and foils were used in a preliminary LSDS experiment at a LANL/LANSCE in Sept. of 2010. The as-received U3O8 powder must be chemically processed to convert it to another chemical form while maintaining its purity, which then must be used to electro-deposit U

  7. Establishment of an Industry-Driven Consortium Focused on Improving the Production Performance of Domestic Stripper Wells

    SciTech Connect

    Joel L. Morrison; Sharon L. Elder

    2006-06-30

    The Pennsylvania State University, under contract to the U.S. Department of Energy (DOE), National Energy Technology Laboratory (NETL) established a national industry-driven Stripper Well Consortium (SWC) that is focused on improving the production performance of domestic petroleum and/or natural gas stripper wells. The consortium creates a partnership with the U.S. petroleum and natural gas producers, trade associations, state funding agencies, academia, and the National Energy Technology Laboratory. This report serves as the ninth quarterly technical progress report for the SWC. Key activities for this reporting period include: (1) Develop and process subcontract awards for the nine projects selected at the 2006 Spring meeting; (2) Continue distribution of the DVD on ''Independent Oil: Rediscovering American's Forgotten Wells''; (3) Improving communications; (4) New member recruitment; (5) Identify SWC projects to be showcased for booth exhibition, preparing an exhibit, promoting and marketing for the 2006 Oklahoma Oil and Gas Trade Expo organized by the OK Marginal Well Commission, Oklahoma City, OK; and (6) Identify projects and draft agenda for the fall technical workshop in Pittsburgh, PA.

  8. Safety evaluation of the ITP filter/stripper test runs and quiet time runs using simulant solution

    SciTech Connect

    Gupta, M.K.

    1993-10-01

    In-Tank Precipitation is a process for removing radioactivity from the salt stored in the Waste Management Tank Farm at Savannah River. The process involves precipitation of cesium and potassium with sodium tetraphenylborate (STPB) and adsorption of strontium and actinides on insoluble sodium titanate (ST) particles. The purpose of this report is to provide the technical bases for the evaluation of Unreviewed Safety Question for the In-Tank Precipitation (ITP) Filter/Stripper Test Runs and Quiet Time Runs Program. The primary objective of the filter-stripper test runs and quiet time runs program is to ensure that the facility will fulfill its design basis function prior to the introduction of radioactive feed. Risks associated with the program are identified and include hazards, both personnel and environmental, associated with handling the chemical simulants; the presence of flammable materials; the potential for damage to the permanenet ITP and Tank Farm facilities. The risks, potential accident scenarios, and safeguards either in place or planned are discussed at length.

  9. Establishment of an Industry-Driven Consortium Focused on Improving the Production Performance of Domestic Stripper Wells

    SciTech Connect

    Joel L. Morrison

    2005-08-30

    The Pennsylvania State University, under contract to the U.S. Department of Energy, National Energy Technology Laboratory will establish, promote, and manage a national industry-driven Stripper Well Consortium (SWC) that will be focused on improving the production performance of domestic petroleum and/or natural gas stripper wells. The consortium creates a partnership with the U.S. petroleum and natural gas industries and trade associations, state funding agencies, academia, and the National Energy Technology Laboratory. This report serves as the nineteenth quarterly technical progress report for the SWC. Key activities for this reporting period include: (1) deliver a keynote luncheon address to the 16th Annual Oil Recovery Conference in Wichita, Kansas, (2) participated in the Interstate Oil & Gas Compact Commission's (IOGCC) Midyear Issues Summit in Anchorage, Alaska, (3) completed and distributed the SWC technical bulletin ''Keeping the Home Wells Flowing: Helping Small Independent Oil and Gas Producers Develop New Technology Solutions'', and (4) completed the primary filming of the Public Broadcast of ''Independent Oil: Rediscovering America's Forgotten Wells''.

  10. ESTABLISHMENT OF AN INDUSTRY-DRIVEN CONSORTIUM FOCUSED ON IMPROVING THE PRODUCTION PERFORMANCE OF DOMESTIC STRIPPER WELLS

    SciTech Connect

    Joel L. Morrison

    2001-06-28

    The Pennsylvania State University, under contract to the US Department of Energy, National Energy Technology Laboratory will establish, promote, and manage a national industry-driven Stripper Well Consortium (SWC) that will be focused on improving the production performance of domestic petroleum and/or natural gas stripper wells. The consortium creates a partnership with the US petroleum and natural gas industries and trade associations, state funding agencies, academia, and the National Energy Technology Laboratory. This report serves as the first quarterly technical progress report for the SWC. The SWC is in its infancy; however, interest from the petroleum and natural gas industry has grown substantially during this reporting period. As of December 31, 2000, nineteen members have joined the consortium and several other companies have expressed interest. During the last three months, efforts were focused on the development of the necessary infrastructure and membership base to begin the consortium technology development activities. These efforts included: (1) preparing a draft constitution and bylaws, (2) developing draft membership application forms, (3) developing an intellectual property statement, (4) providing overview presentations to trade association meetings, and (5) marketing the consortium individually to potential members. These activities are discussed in further detail in this first quarterly technical progress report.

  11. ESTABLISHMENT OF AN INDUSTRY-DRIVEN CONSORTIUM FOCUSED ON IMPROVING THE PRODUCTION PERFORMANCE OF DOMESTIC STRIPPER WELLS

    SciTech Connect

    Joel L. Morrison

    2004-05-10

    The Pennsylvania State University, under contract to the U.S. Department of Energy, National Energy Technology Laboratory will establish, promote, and manage a national industry-driven Stripper Well Consortium (SWC) that will be focused on improving the production performance of domestic petroleum and/or natural gas stripper wells. The consortium creates a partnership with the U.S. petroleum and natural gas industries and trade associations, state funding agencies, academia, and the National Energy Technology Laboratory. This report serves as the eleventh quarterly technical progress report for the SWC. Key activities for this reporting period include: (1) organizing and hosting the Spring SWC meeting in Pearl River, New York, (2) working with successful applicants and Penn State's Office of Sponsored Research to get subcontracts in place, and (3) planning three SWC technology transfer meetings to take place in the fall of 2003. During this reporting period, the efforts were focused primarily on the organizing and hosting the SWC Spring proposal meeting and organizing the fall technology transfer meetings.

  12. Reinforcing the Separators for Lithium/Carbon Cells

    NASA Technical Reports Server (NTRS)

    Du Fresne, E. R.

    1986-01-01

    Fabrication of lithium/carbon batteries simplified by attachment of perforated nickel-foil, graphite-cloth, or graphite-paper backings to glass-fiber separators. Both nickel and carbon backings appear viable. Because perforated nickel foil already manufactured by electroforming, no obstacle to creation of very thin, very porous nickel foil to serve as backing: Thicknesses of 20 micrometers with porosities above 50 percent practicable.

  13. Model calculations of extreme ultraviolet gain from laser-irradiated aluminium foils

    NASA Astrophysics Data System (ADS)

    Pert, G. J.; Tallents, G. J.

    1981-05-01

    Calculations are presented on the development of gain in expanding aluminum plasmas produced by the irradiation of thin foil targets with laser radiation. The atomic physics of the expanding aluminum plasma is also considered together with the question of whether such plasmas can indeed be generated by laser irradiation of foil targets. Two-dimensional fluid code calculations are discussed to demonstrate that the model used in the atomic calculations gives a reasonable representation of the expanding laser plasma. It is pointed out that the development of the hydrogen-like ion recombination laser as an X-ray laser requires the use of ions with Z of about 25. Laser action with aluminum at 38.7 A would be an encouraging step towards X-ray laser action, being about mid-way between the current carbon fiber experiments at 182 A and true X-ray laser action at about 10 A.

  14. On the small divergence of laser-driven ion beams from nanometer thick foils

    SciTech Connect

    Bin, J. H.; Ma, W. J.; Allinger, K.; Kiefer, D.; Khrennikov, K.; Karsch, S.; Krausz, F.; Habs, D.; Schreiber, J.; Wang, H. Y.; Reinhardt, S.; Hilz, P.; Tajima, T.; Yan, X. Q.

    2013-07-15

    We report on experimental studies of divergence of proton beams from nanometer thick diamond-like carbon foils irradiated by a linearly polarized intense laser with high contrast. Proton beams with extremely small divergence (half angle) of 2° are observed in addition with a remarkably well-collimated feature over the whole energy range, showing one order of magnitude reduction of the divergence angle in comparison to the results from μm thick targets. Similar features are reproduced in two-dimensional particle-in-cell simulations with parameters representing our experiments, indicating a strong influence from the electron density distribution on the divergence of protons. Our comprehensive experimental study reveals grand opportunities for using nm foils in experiments that require high ion flux and small divergence.

  15. Gas Foil Bearing Misalignment and Unbalance Effects

    NASA Technical Reports Server (NTRS)

    Howard, Samuel A.

    2008-01-01

    The effects of misalignment and unbalance on gas foil bearings are presented. The future of U.S. space exploration includes plans to conduct science missions aboard space vehicles, return humans to the Moon, and place humans on Mars. All of these endeavors are of long duration, and require high amounts of electrical power for propulsion, life support, mission operations, etc. One potential source of electrical power of sufficient magnitude and duration is a nuclear-fission-based system. The system architecture would consist of a nuclear reactor heat source with the resulting thermal energy converted to electrical energy through a dynamic power conversion and heat rejection system. Various types of power conversion systems can be utilized, but the Closed Brayton Cycle (CBC) turboalternator is one of the leading candidates. In the CBC, an inert gas heated by the reactor drives a turboalternator, rejects excess heat to space through a heat exchanger, and returns to the reactor in a closed loop configuration. The use of the CBC for space power and propulsion is described in more detail in the literature (Mason, 2003). In the CBC system just described, the process fluid is a high pressure inert gas such as argon, krypton, or a helium-xenon mixture. Due to the closed loop nature of the system and the associated potential for damage to components in the system, contamination of the working fluid is intolerable. Since a potential source of contamination is the lubricant used in conventional turbomachinery bearings, Gas Foil Bearings (GFB) have high potential for the rotor support system. GFBs are compliant, hydrodynamic journal and thrust bearings that use a gas, such as the CBC working fluid, as their lubricant. Thus, GFBs eliminate the possibility of contamination due to lubricant leaks into the closed loop system. Gas foil bearings are currently used in many commercial applications, both terrestrial and aerospace. Aircraft Air Cycle Machines (ACMs) and ground

  16. Fabrication of stainless steel foil utilizing chromized steel strip

    NASA Astrophysics Data System (ADS)

    Loria, Edward A.

    1980-10-01

    Stainless steel foil has properties which are, in many respects, unmatched by alternative thin films. The high strength to weight ratio and resistance to corrosion and oxidation at elevated temperatures are generally advantageous. The aerospace and automotive industries have used Type 430 and 304 foil in turbine engine applications. Foil around 2 mils (5.1 × 10-3 cm) thick has been appropriate for the recuperator or heat exchanger and this product has also been used in honeycomb and truss-core structures. Further, such foil has been employed as a wrap to protect tool steel parts from contamination during heat treating. A large part of the high cost of producing stainless steel foil by rolling is due to the complicated and expensive rolling mill and annealing equipment involved. A method will be described which produces (solid) stainless steel foil from chromized (coated) steel which can be cheaper than the conventional processing stainless steel, such as Type 430, from ingot to foil. Also, the material is more ductile and less work hardenable during processing to foil and consequently intermediate annealing treatments are eliminated and scrap losses minimized.

  17. Foil fabrication for the ROMANO event. Revision 1

    SciTech Connect

    Romo, J.G. Jr.; Weed, J.W.; Griggs, G.E.; Brown, T.G.; Tassano, P.L.

    1984-06-13

    The Vacuum Processes Lab (VPL), of LLNL's M.E. Dept. - Material Fabrication Division (MFD), conducted various vacuum related support activities for the ROMANO nuclear physics experiment. This report focuses on the foil fabrication activities carried out between July and November 1983 for the ROMANO event. Other vacuum related activities for ROMANO, such as outgassing tests of materials, are covered in separate documentation. VPL was asked to provide 270 coated Parylene foils for the ROMANO event. However, due to the developmental nature of some of the procedures, approximately 400 coated foils were processed. In addition, VPL interacted with MFD's Plastics Shop to help supply Parylene substrates to other organizations (i.e., LBL and commercial vendors) which had also been asked to provide coated foils for ROMANO. The purposes of this report are (A) to document the processes developed and the techniques used to produce the foils, and (B) to suggest future directions. The report is divided into four sections describing: (1) nuclear target foil fabrication, (2) Parylene substrate preparation and production, (3) calibration foil fabrication, and (4) foil and substrate inspections.

  18. Insulating effectiveness of self-spacing dimpled foil

    NASA Technical Reports Server (NTRS)

    Bond, J. A.

    1972-01-01

    Experimental data are graphed for determining conductive heat losses of multilayer insulation as function of number of foil layers. Foil was 0.0051 cm thick Nb, 1% Zr refractory alloy, dimpled to 0.0254 cm with approximately 28 dimples/sq cm. Heat losses were determined at 0.1 microtorr between 700 and 1089 K.

  19. Process for producing molybdenum foil and collapsible tubing

    NASA Technical Reports Server (NTRS)

    Bretts, G. R.; Gavert, R. B.; Groschke, G. F.

    1971-01-01

    Manufacturing process produces molybdenum foil 0.002 cm thick and 305 m long, and forms foil into high-strength, thin-walled tubing which can be flattened for storage on a spool. Desirable metal properties include high thermal conductivity stiffness, yield and tensile stress, and low thermal expansion coeffecient.

  20. Dynamic responses of a two-dimensional flapping foil motion

    NASA Astrophysics Data System (ADS)

    Lu, Xi-Yun; Liao, Qin

    2006-09-01

    The investigation of a flapping foil, which is used as a basic mode of the flapping-based locomotion in insects, birds, and fish, is performed by solving the Navier-Stokes equations numerically. In this Brief Communication we provide insight into the understanding of dynamics of a flapping foil. A critical flapping Reynolds number based on the flapping frequency and amplitude, above which a forward flapping movement occurs, is predicted. The dynamics of the flapping foil are analyzed in two dynamic responses, i.e., an oscillatory movement and a steady movement, which depend on the density ratio between the foil and the surrounded fluid. The steady movement response is related to the forward flapping motion. The Strouhal number that governs a vortex shedding for the forward flapping foil is calculated and lies in the range where flying and swimming animals will be likely to tune for high propulsive efficiency.

  1. Freezing enhancement around a horizontal tube using copper foil disks

    NASA Astrophysics Data System (ADS)

    Sugawara, M.; Komatsu, Y.; Takahashi, Y.; Beer, H.

    2011-12-01

    Freezing of water saturated in circumferentially arranged copper foils around a cooling tube is studied experimentally and numerically. The copper foils need not to be welded to the cooling tube but are merely placed around the tube so that the freezing system is easily arranged. Copper foils greatly enhance freezing compared with that of a bare tube, even with a small copper volume fraction in the freezing system. Numerical calculations by means of a continuum model predict well freezing enhancement. The effect of the copper foils is also considered numerically for the melting process in order to compare with freezing. It is seen that copper foils contribute more to the melting enhancement than to the increase of the freezing rate.

  2. Tubular hydrogen permeable metal foil membrane and method of fabrication

    DOEpatents

    Paglieri, Stephen N.; Birdsell, Stephen A.; Barbero, Robert S.; Snow, Ronny C.; Smith, Frank M.

    2006-04-04

    A tubular hydrogen permeable metal membrane and fabrication process comprises obtaining a metal alloy foil having two surfaces, coating the surfaces with a metal or metal alloy catalytic layer to produce a hydrogen permeable metal membrane, sizing the membrane into a sheet with two long edges, wrapping the membrane around an elongated expandable rod with the two long edges aligned and overlapping to facilitate welding of the two together, placing the foil wrapped rod into a surrounding fixture housing with the two aligned and overlapping foil edges accessible through an elongated aperture in the surrounding fixture housing, expanding the elongated expandable rod within the surrounding fixture housing to tighten the foil about the expanded rod, welding the two long overlapping foil edges to one another generating a tubular membrane, and removing the tubular membrane from within the surrounding fixture housing and the expandable rod from with the tubular membrane.

  3. Large-area beryllium metal foils

    NASA Astrophysics Data System (ADS)

    Stoner, J. O., Jr.

    1997-02-01

    To manufacture beryllium filters having diameters up to 82 mm and thicknesses in the range 0.1-1 μm, it was necessary to construct apparatus in which the metal could safely be evaporated, and then to find an acceptable substrate and evaporation procedure. The metal was evaporated resistively from a tantalum dimple boat mounted in a baffled enclosure that could be placed in a conventional vacuum bell jar, obviating the need for a dedicated complete vacuum system. Substrates were 102 mm × 127 mm × 0.05 mm cleaved mica sheets, coated with 0.1 μm of NaCl, then with approximately 50 μg/cm 2 of cellulose nitrate. These were mounted on poly(methyl methacrylate) sheets 3 mm thick that were in turn clamped to a massive aluminum block for thermal stability. Details of the processes for evaporation, float off, and mounting are given, and the resulting foils described.

  4. Bombarding insulating foils with highly energetic ions

    NASA Astrophysics Data System (ADS)

    Lanzanò, G.; de Filippo, E.; Hagmann, S.; Rothard, H.; Volant, C.

    Insulating (MYLAR), semi-insulating (MYLAR-Au) and conducting foils have been bombarded by very energetic 64 MeV u-1 78Kr32+ ions. The velocity spectra of fast electrons emitted in the backward and forward directions have been measured and analyzed as a function of the elapsed time in the run. A shift of binary encounter and convoy electrons emitted in the forward direction toward lower velocities has been observed with insulating targets. No such shift occurs with metallic targets. The surface potential evolves with time (i.e. ion fluence) both at forward and backward emission angle. It is shown that strong bulk charging of insulating targets leads to a positive potential as high as 9 kV before charge breakdown.

  5. Preparation of selenium coatings onto beryllium foils

    SciTech Connect

    Erikson, E.D.; Tassano, P.L.; Reiss, R.H.; Griggs, G.E.

    1984-09-01

    A technique for preparing selenium films onto 50.8 microns thick beryllium foils is described. The selenium was deposited in vacuum from a resistance heated evaporation source. Profilometry measurements of the coatings indicate deposit thicknesses of 5.5, 12.9, 37.5, 49.8 and 74.5 microns. The control of deposition rate and of coating thickness was facilitated using a commercially available closed-loop programmable thin film controller. The x-ray transmission of the coated substrates was measured using a tritiated zirconium source. The transmissivities of the film/substrate combination are presented for the range of energies from 4 to 20 keV. 15 references, 3 figures.

  6. Foil Gas Thrust Bearings for High-Speed Turbomachinery

    NASA Technical Reports Server (NTRS)

    Edmonds, Brian; DellaCorte, Christopher; Dykas, Brian

    2010-01-01

    A methodology has been developed for the design and construction of simple foil thrust bearings intended for parametric performance testing and low marginal costs, supporting continued development of oil-free turbomachinery. A bearing backing plate is first machined and surface-ground to produce flat and parallel faces. Partial-arc slots needed to retain the foil components are then machined into the plate by wire electrical discharge machining. Slot thicknesses achievable by a single wire pass are appropriate to accommodate the practical range of foil thicknesses, leaving a small clearance in this hinged joint to permit limited motion. The backing plate is constructed from a nickel-based superalloy (Inconel 718) to allow heat treatment of the entire assembled bearing, as well as to permit hightemperature operation. However, other dimensionally stable materials, such as precipitation-hardened stainless steel, can also be used for this component depending on application. The top and bump foil blanks are cut from stacks of annealed Inconel X-750 foil by the same EDM process. The bump foil has several azimuthal slits separating it into five individual bump strips. This configuration allows for variable bump spacing, which helps to accommodate the effects of the varying surface velocity, thermal crowning, centrifugal dishing, and misalignment. Rectangular tabs on the foil blanks fit into the backing plate slots. For this application, a rather traditional set of conventionally machined dies is selected, and bump foil blanks are pressed into the dies for forming. This arrangement produces a set of bump foil dies for foil thrust bearings that provide for relatively inexpensive fabrication of various bump configurations, and employing methods and features from the public domain.

  7. High strain rate metalworking with vaporizing foil actuator: Control of flyer velocity by varying input energy and foil thickness

    SciTech Connect

    Vivek, A. Hansen, S. R.; Daehn, Glenn S.

    2014-07-15

    Electrically driven rapid vaporization of thin metallic foils can generate a high pressure which can be used to launch flyers at high velocities. Recently, vaporizing foil actuators have been applied toward a variety of impulse-based metal working operations. In order to exercise control over this useful tool, it is imperative that an understanding of the effect of characteristics of the foil actuator on its ability for mechanical impulse generation is developed. Here, foil actuators made out of 0.0508 mm, 0.0762 mm, and 0.127 mm thick AA1145 were used for launching AA2024-T3 sheets of thickness 0.508 mm toward a photonic Doppler velocimeter probe. Launch velocities ranging between 300 m/s and 1100 m/s were observed. In situ measurement of velocity, current, and voltage assisted in understanding the effect of burst current density and deposited electrical energy on average pressure and velocity with foil actuators of various thicknesses. For the pulse generator, geometry, and flyer used here, the 0.0762 mm thick foil was found to be optimal for launching flyers to high velocities over short distances. Experimenting with annealed foil actuators resulted in no change in the temporal evolution of flyer velocity as compared to foil actuators of full hard temper. A physics-based analytical model was developed and found to have reasonable agreement with experiment.

  8. Waste rice seed in conventional and stripper-head harvested fields in California: Implications for wintering waterfowl

    USGS Publications Warehouse

    Fleskes, Joseph P.; Halstead, Brian J.; Casazza, Michael L.; Coates, Peter S.; Kohl, Jeffrey D.; Skalos, Daniel A.

    2012-01-01

    Waste rice seed is an important food for wintering waterfowl and current estimates of its availability are needed to determine the carrying capacity of rice fields and guide habitat conservation. We used a line-intercept method to estimate mass-density of rice seed remaining after harvest during 2010 in the Sacramento Valley (SACV) of California and compared results with estimates from previous studies in the SACV and Mississippi Alluvial Valley (MAV). Posterior mean (95% credible interval) estimates of total waste rice seed mass-density for the SACV in 2010 were 388 (336–449) kg/ha in conventionally harvested fields and 245 (198–307) kg/ha in stripper-head harvested fields; the 2010 mass-density is nearly identical to the mid-1980s estimate for conventionally harvested fields but 36% lower than the mid-1990s estimate for stripped fields. About 18% of SACV fields were stripper-head harvested in 2010 vs. 9–15% in the mid-1990s and 0% in the mid-1980s; but due to a 50% increase in planted rice area, total mass of waste rice seed in SACV remaining after harvest in 2010 was 43% greater than in the mid-1980s. However, total mass of seed-eating waterfowl also increased 82%, and the ratio of waste rice seed to seed-eating waterfowl mass was 21% smaller in 2010 than in the mid-1980s. Mass-densities of waste rice remaining after harvest in SACV fields are within the range reported for MAV fields. However, because there is a lag between harvest and waterfowl use in the MAV but not in the SACV, seed loss is greater in the MAV and estimated waste seed mass-density available to wintering waterfowl in SACV fields is about 5–30 times recent MAV estimates. Waste rice seed remains an abundant food source for waterfowl wintering in the SACV, but increased use of stripper-head harvesters would reduce this food. To provide accurate data on carrying capacities of rice fields necessary for conservation planning, trends in planted rice area, harvest method, and postharvest field

  9. Producing Foils From Direct Cast Titanium Alloy Strip

    NASA Technical Reports Server (NTRS)

    Stuart, T. A.; Gaspar, T. A.; Sukonnik, I. M.; Semiatan, S. L.; Batawi, E.; Peters, J. A.; Fraser, H. L.

    1996-01-01

    This research was undertaken to demonstrate the feasibility of producing high-quality, thin-gage, titanium foil from direct cast titanium strip. Melt Overflow Rapid Solidification Technology (MORST) was used to cast several different titanium alloys into 500 microns thick strip, 10 cm wide and up to 3 m long. The strip was then either ground, hot pack rolled or cold rolled, as appropriate, into foil. Gamma titanium aluminide (TiAl) was cast and ground to approximately 100 microns thick foil and alpha-2 titanium aluminide (Ti3AI) was cast and hot pack rolled to approximately 70 microns thick foil. CP Ti, Ti6Al2Sn4Zr2Mo, and Ti22AI23Nb (Orthorhombic), were successfully cast and cold-rolled into good quality foil (less than 125 microns thick). The foils were generally fully dense with smooth surfaces, had fine, uniform microstructures, and demonstrated mechanical properties equivalent to conventionally produced titanium. By eliminating many manufacturing steps, this technology has the potential to produce thin gage, titanium foil with good engineering properties at significantly reduced cost relative to conventional ingot metallurgy processing.

  10. Pigmented foils for radiative cooling and condensation irrigation

    SciTech Connect

    Nilsson, T.M.J.; Vargas, W.E.; Niklasson, G.A.

    1994-12-31

    This paper reports on the development of pigmented polyethylene foils for radiative cooling. The optical properties of the foils were optimized for applications in day-time radiative cooling and water condensation. The authors first study highly scattering foils used as convection shields. These cover foils combine a high solar reflectance and a high transmittance in the atmospheric window region in the infrared. Different pigment materials were studied and ZnS was the only one that could prevent heating of an underlying blackbody at noon, with the sun in its zenith. A 400 {micro}m thick ZnS pigmented polyethylene foil with a pigment volume fraction of 0.15 was tested in Tanzania. At noon the observed temperature of the covered blackbody was only 1.5 K above the ambient. Secondly, they study the potential for condensation of water in an arid region. Pigmented foils for this purpose should combine a high solar reflectance and a high infrared emittance, in order to promote condensation by the radiative cooling effect. Titanium dioxide is a fairly good infrared emitter, but the emittance can be improved by using a mixture of TiO{sub 2} and BaSO{sub 4} pigments or only employing a composite SiO{sub 2}/TiO{sub 2}. Field tests with a 390 {micro}m thick polyethylene foil with TiO{sub 2} and BaSO{sub 4} pigments gave encouraging results.

  11. Compliant Foil Journal Bearing Performance at Alternate Pressures and Temperatures

    NASA Technical Reports Server (NTRS)

    Bruckner, Robert J.; Puleo, Bernadette J.

    2008-01-01

    An experimental test program has been conducted to determine the highly loaded performance of current generation gas foil bearings at alternate pressures and temperatures. Typically foil bearing performance has been reported at temperatures relevant to turbomachinery applications but only at an ambient pressure of one atmosphere. This dearth of data at alternate pressures has motivated the current test program. Two facilities were used in the test program, the ambient pressure rig and the high pressure rig. The test program utilized a 35 mm diameter by 27 mm long foil journal bearing having an uncoated Inconel X-750 top foil running against a shaft with a PS304 coated journal. Load capacity tests were conducted at 3, 6, 9, 12, 15, 18, and 21 krpm at temperatures from 25 to 500 C and at pressures from 0.1 to 2.5 atmospheres. Results show an increase in load capacity with increased ambient pressure and a reduction in load capacity with increased ambient temperature. Below one-half atmosphere of ambient pressure a dramatic loss of load capacity is experienced. Additional lightly loaded foil bearing performance in nitrogen at 25 C and up to 48 atmospheres of ambient pressure has also been reported. In the lightly loaded region of operation the power loss increases for increasing pressure at a fixed load. Knowledge of foil bearing performance at operating conditions found within potential machine applications will reduce program development risk of future foil bearing supported turbomachines.

  12. Experimental evidence of beam-foil plasma creation during ion-solid interaction

    NASA Astrophysics Data System (ADS)

    Sharma, Prashant; Nandi, Tapan

    2016-08-01

    Charge state evolution of the energetic projectile ions during the passage through thin carbon foils has been revisited using the X-ray spectroscopy technique. Contributions from the bulk and the solid surface in the charge changing processes have been segregated by measuring the charge state distribution of the projectile ions in the bulk of the target during the ion-solid interaction. Interestingly, the charge state distribution measured in the bulk exhibits Lorentzian profile in contrast to the well-known Gaussian structure observed using the electromagnetic methods and the theoretical predictions. The occurrence of such behavior is a direct consequence of the imbalance between charge changing processes, which has been seen in various cases of the laboratory plasma. It suggests that the ion-solid collisions constitute high-density, localized plasma in the bulk of the solid target, called the beam-foil plasma. This condensed beam-foil plasma is similar to the high-density solar and stellar plasma which may have practical implementations in various fields, in particular, plasma physics and nuclear astrophysics. The present work suggests further modification in the theoretical charge state distribution calculations by incorporating the plasma coupling effects during the ion-solid interactions. Moreover, the multi-electron capture from the target exit surface has been confirmed through comparison between experimentally measured and theoretically predicted values of the mean charge state of the projectile ions.

  13. CO2 laser-fabricated cladding light strippers for high-power fiber lasers and amplifiers.

    PubMed

    Boyd, Keiron; Simakov, Nikita; Hemming, Alexander; Daniel, Jae; Swain, Robert; Mies, Eric; Rees, Simon; Andrew Clarkson, W; Haub, John

    2016-04-10

    We present and characterize a simple CO2 laser processing technique for the fabrication of compact all-glass optical fiber cladding light strippers. We investigate the cladding light loss as a function of radiation angle of incidence and demonstrate devices in a 400 μm diameter fiber with cladding losses of greater than 20 dB for a 7 cm device length. The core losses are also measured giving a loss of <0.008±0.006  dB/cm. Finally we demonstrate the successful cladding light stripping of a 300 W laser diode with minimal heating of the fiber coating and packaging adhesives. PMID:27139854

  14. Mechanical properties of micro- and nanocrystalline diamond foils

    PubMed Central

    Lodes, M. A.; Kachold, F. S.; Rosiwal, S. M.

    2015-01-01

    Diamond coating of suitable template materials and subsequent delamination allows for the manufacturing of free-standing diamond foil. The evolution of the microstructure can be influenced by secondary nucleation via control of process conditions in the hot-filament chemical vapour deposition process. Bending tests show extraordinarily high strength (more than 8 GPa), especially for diamond foils with nanocrystalline structure. A detailed fractographic analysis is conducted in order to correlate measured strength values with crack-initiating defects. The size of the failure causing flaw can vary from tens of micrometres to tens of nanometres, depending on the diamond foil microstructure as well as the loading conditions. PMID:25713455

  15. Material compatibility evaluation for liquid oxygen turbopump fluid foil bearings

    NASA Technical Reports Server (NTRS)

    Stoltzfus, J. M.; Dees, J.; Gu, A.; Dolan, F.

    1992-01-01

    Three series of tests were carried out on three polymer-coated Inconel substrate materials, Teflon S, polyimide bonded graphite fluoride (PBGF), and Teflon, which are considered for use in fluid foil bearings for a liquid oxygen turbopump. All the candidate materials passed the liquid oxygen frictional heating test. During the gaseous oxygen frictional heating test, all coatings wore off before ignition occured. Both Teflon S and PBGF coated foils passed 100 start/stop cycles against chrome-plated Inconel 718 shaft in the direct foil bearing lift-off simulation test in liquid oxygen.

  16. Method for laser welding ultra-thin metal foils

    DOEpatents

    Pernicka, J.C.; Benson, D.K.; Tracy, C.E.

    1996-03-26

    A method for simultaneously cutting and welding ultra-thin foils having a thickness of less than 0.002 inches wherein two ultra-thin films are stacked and clamped together. A pulsed laser such as of the Neodymium: YAG type is provided and the beam of the laser is directed onto the stacked films to cut a channel through the films. The laser is moved relative to the stacked foils to cut the stacked foils at successive locations and to form a plurality of connected weld beads to form a continuous weld. 5 figs.

  17. Method for laser welding ultra-thin metal foils

    DOEpatents

    Pernicka, John C.; Benson, David K.; Tracy, C. Edwin

    1996-01-01

    A method for simultaneously cutting and welding ultra-thin foils having a thickness of less than 0.002 inches wherein two ultra-thin films are stacked and clamped together. A pulsed laser such as of the Neodymium: YAG type is provided and the beam of the laser is directed onto the stacked films to cut a channel through the films. The laser is moved relative to the stacked foils to cut the stacked foils at successive locations and to form a plurality of connected weld beads to form a continuous weld.

  18. Hermetic packaging of drugs: optimized sealing of foil pouches.

    PubMed

    Auslander, D E; Gilbert, S G

    1976-07-01

    Factors affecting the sealing of foil packages were studied in the sealing of foil packages were studied in three laboratories. The relationship of sealing temperature (with machine speed and pressure kept constant) to the incidence of defective packages was determined. The maximum acceptable limit for defective pouches was 1%. Three tests were employed to detect defects: vacuum-dye, seal strength, and pressurized ammonia vapor. Only the last was sensitive enough to determine the optimum sealing conditions. This test also was capable of detecting leakage sites. Replacement of the cellophane layer of the foil laminate with polyvinylidene chloride-coated polyester improved the barrier properties of the package. PMID:957113

  19. Mechanical properties of micro- and nanocrystalline diamond foils.

    PubMed

    Lodes, M A; Kachold, F S; Rosiwal, S M

    2015-03-28

    Diamond coating of suitable template materials and subsequent delamination allows for the manufacturing of free-standing diamond foil. The evolution of the microstructure can be influenced by secondary nucleation via control of process conditions in the hot-filament chemical vapour deposition process. Bending tests show extraordinarily high strength (more than 8 GPa), especially for diamond foils with nanocrystalline structure. A detailed fractographic analysis is conducted in order to correlate measured strength values with crack-initiating defects. The size of the failure causing flaw can vary from tens of micrometres to tens of nanometres, depending on the diamond foil microstructure as well as the loading conditions. PMID:25713455

  20. Method of fabricating a uranium-bearing foil

    SciTech Connect

    Gooch, Jackie G.; DeMint, Amy L.

    2012-04-24

    Methods of fabricating a uranium-bearing foil are described. The foil may be substantially pure uranium, or may be a uranium alloy such as a uranium-molybdenum alloy. The method typically includes a series of hot rolling operations on a cast plate material to form a thin sheet. These hot rolling operations are typically performed using a process where each pass reduces the thickness of the plate by a substantially constant percentage. The sheet is typically then annealed and then cooled. The process typically concludes with a series of cold rolling passes where each pass reduces the thickness of the plate by a substantially constant thickness amount to form the foil.

  1. On the performance of hybrid foil-magnetic bearings

    SciTech Connect

    Heshmat, H.; Chen, H.M.; Walton, J.F. II.

    2000-01-01

    Recent technological advancements make hybridization of the magnetic and foil bearing both possible and extremely attractive. Operation of the foil/magnetic bearings takes advantage of the strengths of each individual bearing while minimizing each others weaknesses. In this paper one possible hybrid foil and magnetic bearing arrangement is investigated and sample design and operating parameters are presented. One of the weaknesses of the foil bearings, like any hydrodynamic bearing, is that contact between the foil bearing and the shaft occurs at rest or at very low speeds and it has low load carrying capacity at low speed. For high speed applications, AMBs are, however, vulnerable to rotor-bending or structural resonances that can easily saturate power amplifiers and make the control system unstable. Since the foil bearing is advantageous for high speed operation with a higher load carrying capacity, and the magnetic bearing is so in low speed range, it is a natural evolution to combine them into a hybrid bearing system thus utilizing the advantages of both. To take full advantage of the foil and magnetic elements comprising a hybrid bearing, it is imperative that the static and dynamic characteristics of each bearing be understood. This paper describes the development of a new analysis technique that was used to evaluate the performance of a class of gas-lubricated journal bearing. Unlike conventional approaches, the solution of the governing hydrodynamic equations dealing with compressible fluid is coupled with the structural resiliency of the bearing surface. The distribution of the fluid film thickness and pressures, as well as the shear stresses in a finite-width journal bearing, are computed. Using the Finite Element (FE) method, the membrane effect of an elastic top foil was evaluated and included in the overall analytical procedure. Influence coefficients were generated to address the elasticity effects of combined top foil and elastic foundation on the

  2. Functional multi-band THz meta-foils

    PubMed Central

    Wu, Jianfeng; Moser, Herbert O.; Xu, Su; Jian, Linke; Banas, Agnieszka; Banas, Krzysztof; Chen, Hongsheng; Bettiol, Andrew A.; Breese, Mark B. H.

    2013-01-01

    In this paper, we present the first experimental demonstration of double- and triple-band negative refraction index meta-foils in the terahertz (THz) region. Multi-band meta-foils constructed by multi-cell S-string resonators in a single structure exhibit simultaneously negative permittivity and negative permeability responses at multiple frequencies. The phenomena are confirmed by numerical simulations and Fourier transform infrared spectroscopy measurements. The flexible, freestanding multi-band meta-foils provide a promising candidate for the development of multi-frequency THz materials and devices. PMID:24346309

  3. Elevated Temperature Tensile Tests on DU–10Mo Rolled Foils

    SciTech Connect

    Schulthess, Jason

    2014-09-01

    Tensile mechanical properties for uranium-10 wt.% molybdenum (U–10Mo) foils are required to support modeling and qualification of new monolithic fuel plate designs. It is expected that depleted uranium-10 wt% Mo (DU–10Mo) mechanical behavior is representative of the low enriched U–10Mo to be used in the actual fuel plates, therefore DU-10Mo was studied to simplify material processing, handling, and testing requirements. In this report, tensile testing of DU-10Mo fuel foils prepared using four different thermomechanical processing treatments were conducted to assess the impact of foil fabrication history on resultant tensile properties.

  4. Study on metal foil explosion using high current

    NASA Astrophysics Data System (ADS)

    Mihara, Takayuki; Matsuo, N.; Otsuka, M.; Itoh, S.

    2009-12-01

    In the high energy processing using explosive, there are variety of application examples which is explosion welding of differential metallic plate and powder compaction of diamond. However a rule legal to explosives is severe and needs many efforts for handling qualification acquisition, maintenance, and security. In this research, the metallic foil explosion using high current is paid my attention to the method to obtain linear or planate explosive initiation easily, and the main evaluation of metallic foil explosion was conducted. The explosion power was evaluated by observing optically the underwater shock wave generated from the metallic foil explosion.

  5. Study on metal foil explosion using high current

    NASA Astrophysics Data System (ADS)

    Mihara, Takayuki; Matsuo, N.; Otsuka, M.; Itoh, S.

    2010-03-01

    In the high energy processing using explosive, there are variety of application examples which is explosion welding of differential metallic plate and powder compaction of diamond. However a rule legal to explosives is severe and needs many efforts for handling qualification acquisition, maintenance, and security. In this research, the metallic foil explosion using high current is paid my attention to the method to obtain linear or planate explosive initiation easily, and the main evaluation of metallic foil explosion was conducted. The explosion power was evaluated by observing optically the underwater shock wave generated from the metallic foil explosion.

  6. Synchronization and Phase Dynamics of Oscillating Foils

    NASA Astrophysics Data System (ADS)

    Finkel, Cyndee L.

    In this work, a two-dimensional model representing the vortices that animals produce, when they are ying/swimming, was constructed. A D{shaped cylinder and an oscillating airfoil were used to mimic these body{shed and wing{generated vortices, respectively. The parameters chosen are based on the Reynolds numbers similar to that which is observed in nature (˜10 4). In order to imitate the motion of ying/swimming, the entire system was suspended into a water channel from frictionless air{bearings. The position of the apparatus in the channel was regulated with a linear, closed loop PI controller. Thrust/drag forces were measured with strain gauges and particle image velocimetry (PIV) was used to examine the wake structure that develops. The Strouhal number of the oscillating airfoil was compared to the values observed in nature as the system transitions between the accelerated and steady states. The results suggest that self-regulation restricts the values of the Strouhal number to a certain range where no other external sensory input is necessary. As suggested by previous work, this self-regulation is a result of a limit cycle process that stems from nonlinear periodic oscillations. The limit cycles were used to examine the synchronous conditions due to the coupling of the foil and wake vortices. Noise is a factor that can mask details of the synchronization. In order to control its effect, we study the locking conditions using an analytic technique that only considers the phases. Our results show that the phase locking indices are dependent on the Strouhal value as it converges to a frequency locking ratio of ≃0:5. This indicates that synchronization occurs during cruising between the motion of the foil and the measured thrust/drag response of the uid forces. The results suggest that Strouhal number selection in steady forward natural swimming and ying is the result of a limit cycle process and not actively controlled by an organism. An implication of this is

  7. Characterization of Electrodeposited Technetium on Gold Foil

    SciTech Connect

    Mausolf, Edward; Poineau, Frederic; Hartmann, Thomas; Droessler, Janelle; Czerwinski, Ken

    2011-11-17

    The reduction and electrodeposition of TcO{sub 4}{sup -} on a smooth gold foil electrode with an exposed area of 0.25 cm{sup 2} was performed in 1 M H{sub 2}SO{sub 4} supporting electrolyte using bulk electrolysis with a constant current density of 1.0 A/cm{sup 2} at a potential of -2.0 V. Significant hydrogen evolution accompanied the formation of Tc deposits. Tc concentrations consisted of 0.01 M and 2 x 10{sup -3} M and were electrodeposited over various times. Deposited fractions of Tc were characterized by powder x-ray diffraction, x-ray absorption fine structure spectroscopy, and scanning electron microscopy with the capability to measure semiquantitative elemental compositions by energy-dispersive x-ray emission spectroscopy. Results indicate the presence of Tc metal on all samples as the primary electrodeposited constituent for all deposition times and Tc concentrations. Thin films of Tc have been observed followed by the formation of beads that are removable by scratching. After 2000, the quantity of Tc removed from solution and deposited was 0.64 mg Tc per cm{sup 2}. The solution, after electrodeposition, showed characteristic absorbances near 500 nm corresponding to hydrolyzed Tc(IV) produced during deposition of Tc metal. No detectable Tc(IV) was deposited to the cathode.

  8. Investigation of various criteria for evaluation of aluminum thin foil ''smart sensors'' images

    NASA Astrophysics Data System (ADS)

    Panin, S. V.; Eremin, A. V.; Lyubutin, P. S.; Burkov, M. V.

    2014-10-01

    Various criteria for processing of aluminum foil ''smart sensors'' images for fatigue evaluation of carbon fiber reinforced polymer (CFRP) were analyzed. There are informative parameters used to assess image quality and surface relief and accordingly to characterize the fatigue damage state of CFRP. The sensitivity of all criteria to distortion influences, particularly, to Gaussian noise, blurring and JPEG compression was investigated. The main purpose of the research is related to the search of informative parameters for fatigue evaluation, which are the least sensitive to different distortions.

  9. Indium foil with beryllia washer improves transistor heat dissipation

    NASA Technical Reports Server (NTRS)

    Hilliard, J.; John, J. E. A.

    1964-01-01

    Indium foil, used as an interface material in transistor mountings, greatly reduces the thermal resistance of beryllia washers. This method improves the heat dissipation of power transistors in a vacuum environment.

  10. Stratification in Al and Cu foils exploded in vacuum

    SciTech Connect

    Baksht, R. B.; Rousskikh, A. G.; Zhigalin, A. S.; Artyomov, A. P.; Oreshkin, V. I.

    2015-10-15

    An experiment with exploding foils was carried out at a current density of 0.7 × 10{sup 8} A/cm{sup 2} through the foil with a current density rise rate of about 10{sup 15} A/cm{sup 2} s. To record the strata arising during the foil explosions, a two-frame radiographic system was used that allowed tracing the dynamics of strata formation within one shot. The original striation wavelength was 20–26 μm. It was observed that as the energy deposition to a foil stopped, the striation wavelength increased at a rate of ∼(5–9) × 10{sup 3} cm/s. It is supposed that the most probable reason for the stratification is the thermal instability that develops due to an increase in the resistivity of the metal with temperature.

  11. Positron annihilation lifetime spectroscopy study of Kapton thin foils

    NASA Astrophysics Data System (ADS)

    Kanda, G. S.; Ravelli, L.; Löwe, B.; Egger, W.; Keeble, D. J.

    2016-01-01

    Variable energy positron annihilation lifetime spectroscopy (VE-PALS) experiments on polyimide material Kapton are reported. Thin Kapton foils are widely used in a variety of mechanical, electronic applications. PALS provides a sensitive probe of vacancy-related defects in a wide range of materials, including open volume in polymers. Varying the positron implantation energy enables direct measurement of thin foils. Thin Kapton foils are also commonly used to enclose the positron source material in conventional PALS measurements performed with unmoderated radionuclide sources. The results of depth-profiled positron lifetime measurements on 7.6 μm and 25 μm Kapton foils are reported and determine a dominant 385(1) ps lifetime component. The absence of significant nanosecond lifetime component due to positronium formation is confirmed.

  12. The transonic multi-foil Augmentor-Wing

    NASA Technical Reports Server (NTRS)

    Farbridge, J. E.; Smith, R. C.

    1977-01-01

    The paper describes the development of a transonic blown multi-foil Augmentor-Wing airfoil section that has a thickness/chord (t/c) value of 0.18. In comparison with an unblown single-foil supercritical section of the same overall t/c the new multi-foil section is characterized by an increased drag rise Mach number, increased buffet boundaries, and a reduction in 'effective' drag due to blowing. Potential advantages of the Augmentor-Wing are considered and the testing of three high-speed models in a trisonic pressurized wind tunnel (possessing a two-dimensional transonic insert) is discussed. The data indicate that a very thick wing is feasible since separations toward the rear of the main foil can be controlled both by shroud location and augmentor blowing.

  13. Coherent multiple-foil x-ray transition radiation

    SciTech Connect

    Moran, M.J.; Chang, B.; Schneider, M.B.

    1993-08-25

    Intense x-ray transition radiation can be generated when relativistic electrons pass through a multiple-foil target. When the foil spacing is periodic, the transition radiation can be spatially coherent with respect to the target period. The spatial coherence can be evident in the spectra and angular distributions of transition radiation from such targets. A series of experiments has measured coherent transition radiation distributions from multiple-foil targets (up to six foils) with spacings of 50 {mu}m and 100 {mu}m. The electron energy was about 75 MeV and the photon energies were about 200 eV. Agreement between calculation and experimental data is excellent.

  14. Stratification in Al and Cu foils exploded in vacuum

    NASA Astrophysics Data System (ADS)

    Baksht, R. B.; Rousskikh, A. G.; Zhigalin, A. S.; Oreshkin, V. I.; Artyomov, A. P.

    2015-10-01

    An experiment with exploding foils was carried out at a current density of 0.7 × 108 A/cm2 through the foil with a current density rise rate of about 1015 A/cm2 s. To record the strata arising during the foil explosions, a two-frame radiographic system was used that allowed tracing the dynamics of strata formation within one shot. The original striation wavelength was 20-26 μm. It was observed that as the energy deposition to a foil stopped, the striation wavelength increased at a rate of ˜(5-9) × 103 cm/s. It is supposed that the most probable reason for the stratification is the thermal instability that develops due to an increase in the resistivity of the metal with temperature.

  15. Methods for the recovery of sulfur components from flue gas and recycle sodium sulfite by reduction-smelting and carbonating to strip hydrogen sulfide

    SciTech Connect

    Farin, W.G.

    1980-12-23

    An improved method for recovering sulfur from flue gas which contains sulfur dioxide formed from burning sulfur containing fuels is disclosed. The method first involves the reduction burning of auxilary fuel in the presence of sodium sulfite to convert it to smelt containing sodium sulfide and sodium carbonate. The smelt is dissolved, and the solution reacted with carbon dioxide, hydrogen sulfide and water vapor forming sodium hydrosulfide. The sodium hydrosulfide is reacted with a high concentration of recycled sodium bicarbonate and stripped with carbon dioxide to form sodium carbonate and release the sulfides as hydrogen sulfide from the stripper. The hydrogen sulfide released is then converted to sulfur dioxide, sulfuric acid or elemental sulfur. Pressurized carbon dioxide is used for pressure carbonation of recycled solution from the stripper to convert the sodium carbonate to the high concentration of recycled sodium bicarbonate used for stripping. The sodium carbonate and sodium bicarbonate from the stripper are reacted under pressure with sodium bisulfite in a decarbonator to form sodium sulfite and release carbon dioxide under pressure for use in the pressure carbonation. A portion of the sodium sulfite formed by decarbonation is then reduced in the smelter. The balance of the sodium sulfite is then used for absorption of the sulfur dioxide from the flue gas forming the sodium bisulfite used for decarbonation.

  16. Evidence of muonium formation using thin gold foils in vacuum

    NASA Technical Reports Server (NTRS)

    Barnett, B. A.; Chang, C. Y.; Steinberg, P.; Yodh, G. B.; Orr, H. D.; Carroll, J. B.; Eckhause, M.; Kane, J. R.; Spence, C. B.; Hsieh, C. S.

    1977-01-01

    The production of thermal muonium in a vacuum region has been investigated using an array of 200 thin (about 1000 A thick) gold foils exposed to a stopping positive-muon beam. By examining the observed time dependence of the positive-muon decay spectra in various transverse magnetic field, it is estimated that the lower limit of the probability of muonium formation by these gold foils placed in vacuum was 0.28 plus or minus 0.05.

  17. Two-Dimensional Dynamic Simulation of a Continuous Foil Bearing

    NASA Technical Reports Server (NTRS)

    Braun, M. Jack; Choy, F. K.; Dzodzo, Milorad; Hsu, J.

    1996-01-01

    In this paper, the two dimensional(radial and circumferential) transient Navier-Stokes equations are used to solve the hydrodynamic problem in conjunction with the time dependent motion of the journal, and the deformable, spring supported foil. The elastic deformation of the foil and its supports are simulated by a finite element model. The time-dependent Navier-Stokes formulation is used to solve for the interaction between the fluid lubricant, the motion of the journal and the deformable foil boundary. The steady state, the quasi-transient and the full transient dynamic simulation of the foil-fluid journal interaction are examined on a comparative basis. For the steady state simulation, the fluid lubricant pressures are evaluated for a particular journal position, by means of an iterative scheme until convergence is achieved in both the fluid pressures and the corresponding foil deformation. For the quasi-transient case, the transient motion of the journal is calculated using a numerical integration scheme for the velocity and displacement of the journal. The deformation of the foil is evaluated through numerical iteration in feedback mode with the fluid film pressure generated by the journal motion until convergence at every time step is achieved. For the full transient simulation, a parallel real-time integration scheme is used to evaluate simultaneously the new journal position and the new deformed shape of the foil at each time step. The pressure of the fluid lubricant is iterated jointly with the corresponding journal position and the deformed foil geometry until convergence is achieved. A variable time-stepping Newmark-Beta integration procedure is used to evaluate the transient dynamics at each time step of the bearing.

  18. D-Cluster Converter Foil for Laser-Accelerated Deuteron Beams: Towards Deuteron-Beam-Driven Fast Ignition

    SciTech Connect

    Miley, George H.

    2012-10-24

    Fast Ignition (FI) uses Petawatt laser generated particle beam pulse to ignite a small volume called a pre-compressed Inertial Confinement Fusion (ICF) target, and is the favored method to achieve the high energy gain per target burn needed for an attractive ICF power plant. Ion beams such as protons, deuterons or heavier carbon ions are especially appealing for FI as they have relative straight trajectory, and easier to focus on the fuel capsule. But current experiments have encountered problems with the 'converter-foil' which is irradiated by the Petawatt laser to produce the ion beams. The problems include depletion of the available ions in the convertor foils, and poor energy efficiency (ion beam energy/ input laser energy). We proposed to develop a volumetrically-loaded ultra-high-density deuteron deuterium cluster material as the basis for converter-foil for deuteron beam generation. The deuterons will fuse with the ICF DT while they slow down, providing an extra 'bonus' energy gain in addition to heating the hot spot. Also, due to the volumetric loading, the foil will provide sufficient energetic deuteron beam flux for 'hot spot' ignition, while avoiding the depletion problem encountered by current proton-driven FI foils. After extensive comparative studies, in Phase I, high purity PdO/Pd/PdO foils were selected for the high packing fraction D-Cluster converter foils. An optimized loading process has been developed to increase the cluster packing fraction in this type of foil. As a result, the packing fraction has been increased from 0.1% to 10% - meeting the original Phase I goal and representing a significant progress towards the beam intensities needed for both FI and pulsed neutron applications. Fast Ignition provides a promising approach to achieve high energy gain target performance needed for commercial Inertial Confinement Fusion (ICF). This is now a realistic goal for near term in view of the anticipated ICF target burn at the National Ignition

  19. 21 CFR 189.301 - Tin-coated lead foil capsules for wine bottles.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Tin-coated lead foil capsules for wine bottles... lead foil capsules for wine bottles. (a) Tin-coated lead foil is composed of a lead foil coated on one... covering applied over the cork and neck areas) on wine bottles to prevent insect infestation, as a...

  20. 21 CFR 189.301 - Tin-coated lead foil capsules for wine bottles.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Tin-coated lead foil capsules for wine bottles. 189... lead foil capsules for wine bottles. (a) Tin-coated lead foil is composed of a lead foil coated on one... covering applied over the cork and neck areas) on wine bottles to prevent insect infestation, as a...

  1. Electrospray ionization with aluminum foil: A versatile mass spectrometric technique.

    PubMed

    Hu, Bin; So, Pui-Kin; Yao, Zhong-Ping

    2014-03-19

    In this study, we developed a novel electrospray ionization (ESI) technique based on household aluminum foil (Al foil) and demonstated the desirable features and applications of this technique. Al foil can be readily cut and folded into desired configuration for effective ionization and for holding sample solution in bulk to allowing acquisition of durable ion signals. The present technique was demonstrated to be applicable in analysis of a wide variety of samples, ranging from pure chemical and biological compounds, e.g., organic compounds and proteins, to complex samples in liquid, semi-solid, and solid states, e.g., beverages, skincare cream, and herbal medicines. The inert, hydrophobic and impermeable surface of Al foil allows convenient and effective on-target extraction of solid samples and on-target sample clean-up, i.e., removal of salts and detergents from proteins and peptides, extending ESI device from usually only for sample loading and ionization to including sample processing. Moreover, Al foil is an excellent heat-conductor and highly heat-tolerant, permitting direct monitoring of thermal reactions, e.g., thermal denaturation of proteins. Overall, the present study showed that Al-foil ESI could be an economical and versatile method that allows a wide range of applications. PMID:24594810

  2. Instability studies in radial foil configurations on the COBRA generator

    NASA Astrophysics Data System (ADS)

    Gourdain, P.-A.; Greenly, J. B.; Hammer, D. A.; Knapp, P. F.; Kusse, B. R.; Pikuz, S. A.; Schrafel, P. C.; Shelkovenko, T. C.

    2010-11-01

    Radial foil configurations prove to be a very simple experimental set up to study high energy density plasmas. A 5-micron thin metallic foil lies flat over a stretcher which is connected to the anode of a pulsed power generator such as COBRA (1MA, 100 ns current rise time). The cathode contacts the foil at its geometrical center using a hollow stainless steel pin. As the foil ablates, JxB forces lift the foil leading to the formation a plasma bubble surrounding a central plasma column, which is a z-pinch. Force densities on this column should increase considerably as the initial pin diameter is diminished and we expect plasma properties to change accordingly. Based only on pin diameter considerations, radial foil explosions could produce magnetic pressures ranging from 160 kbar (for 2-mm pins) to 2.5 Mbar (for 0.5-mm pins). However, as the cathode diameter diminishes, instabilities appear earlier in the discharge, preventing the z-pinch implosion to occur at maximum current, de facto limiting plasma parameters. We investigate the cause of these instabilities, the possible means to reduce plasma instabilities and to improve plasma performances.

  3. Propulsion of a flexible foil in a fluid

    NASA Astrophysics Data System (ADS)

    Venkatraman, Kartik; Chaithanya, Ravi

    2008-11-01

    The dynamic properties such as time dependent pressure loading, free stream velocity, and local acceleration of the hydrofoil determine the instantaneous deformation of a flexible foil. The present work is concerned with the effect of structural dynamic terms and inertia loads on a flexible foil undergoing large amplitude rigid body harmonic wave-like motion in an unsteady potential flow. The hydrofoil structural dynamics is modeled as an Euler-Bernoulli beam finite element. The unsteady fluid dynamic force is evaluated using a numerical discrete vortex implementation of an unsteady incompressible potential flow model. The hydrofoil is fixed at its leading edge and it moves with velocity parallel to its length in the undeformed state. The propulsion of the hydro-elastic system is studied in terms of the mass ratio of the foil and the fluid, as well as its structural flexibility. It is shown that the thrust coefficient and propulsive efficiency of the flexible foil decreases with increase in structural flexibility. We made a comparison of the effect of structural flexibility on the thrust coefficient and propulsive efficiency considering models of the oscillating foil with inertia and without inertia effects present. Detailed parametric studies of the effect of different parameters on propulsion of the foil were made. Including inertia loads and structural dynamic terms significantly affect the propulsive efficiency and thrust coefficient.

  4. Globally shed wakes for three distinct retracting foil geometries

    NASA Astrophysics Data System (ADS)

    Steele, Stephanie; Triantafyllou, Michael

    2015-11-01

    In quickly retracting foils at an angle of attack, the boundary layer vorticity along with the added mass energy is immediately and globally shed from the body into the surrounding fluid. The deposited vorticity quickly reforms into lasting vortex structures, which could be used for purposes such as manipulating or exploiting the produced flow structures by additional bodies in the fluid. The globally shed wake thus entrains the added mass energy provided by the initially moving body, reflected by the value of the circulation left in the wake. In studying experimentally as well as numerically this phenomenon, we find that the three different tested geometries leave behind distinct wakes. Retracting a square-ended foil is undesirable because the deposited wake is complicated by three-dimensional ring vorticity effects. Retracting a tapered, streamlined-tipped foil is also undesirable because the shape-changing aspect of the foil geometry actually induces energy recovery back to the retracting foil, leaving a less energetic globally shed wake. Finally, a retracting hollow foil geometry avoids both of these detrimental effects, leaving relatively simple, yet energetic, vortex structures in the wake.

  5. FeN foils by nitrogen ion-implantation

    SciTech Connect

    Jiang, Yanfeng; Wang, Jian-Ping; Al Mehedi, Md; Fu, Engang; Wang, Yongqiang

    2014-05-07

    Iron nitride samples in foil shape (free standing, 500 nm in thickness) were prepared by a nitrogen ion-implantation method. To facilitate phase transformation, the samples were bonded on the substrate followed by a post-annealing step. By using two different substrates, single crystal Si and GaAs, structural and magnetic properties of iron nitride foil samples prepared with different nitrogen ion fluences were characterized. α″-Fe{sub 16}N{sub 2} phase in iron nitride foil samples was obtained and confirmed by the proposed approach. A hard magnetic property with coercivity up to 780 Oe was achieved for the FeN foil samples bonded on Si substrate. The feasibility of using nitrogen ion implantation techniques to prepare FeN foil samples up to 500 nm thickness with a stable martensitic phase under high ion fluences has been demonstrated. A possible mechanism was proposed to explain this result. This proposed method could potentially be an alternative route to prepare rare-earth-free FeN bulk magnets by stacking and pressing multiple free-standing thick α″-Fe{sub 16}N{sub 2} foils together.

  6. Evaluation of the Brinecell{reg_sign} electrochemical oxidation unit for destruction of noncyanide strippers and other colored compounds in wastewaters

    SciTech Connect

    Wikoff, P.M.; Suciu, D.F.

    1994-08-01

    The noncyanide strippers used in the plating operations at Kelly Air Force Base, in San Antonio, Texas, develop an intense red color during use. Currently, the spent strippers cannot be treated in the Industrial Wastewater Treatment Plant because, even after biological treatment, the color remains too high for discharge. The Brinecell{reg_sign} process was evaluated for its application in treating the spent stripping solutions. The Brinecell{reg_sign} produces strong oxidizing agents that could treat the color causing compounds. The Brinecell{reg_sign} process was used to treat a 1 to 400 dilution of spent Clepo 204-T at 50 C and 60 g/L salt. After 8 hours of treatment, the color remaining was 8 units and the solution appeared colorless. Treatment of the Metalx B-9 reduced the color to 60 units. The effect of salt concentration, solution temperature, and solution pH was evaluated on the Brinecell{reg_sign} treatment process.

  7. SU-E-T-151: Enhanced Radiation Attenuation with Multi-Layer Foils

    SciTech Connect

    Warmington, L; Watanabe, Y

    2014-06-01

    Purpose: To evaluate the effect of increasing the number of thin high Z foils on the dose enhancement and the overall radiation attenuation with a 24MV photon beam. Methods: DOSXYZnrc was used to perform Monte Carlo simulations of multi-layer lead foil configurations. The foil size was 7cm x 7cm. and the foil thickness was adjusted to give a combined thickness of 1mm. The number of foils used was 4, 6, 8, and 10. The separation between foils was also varied from 3 to 9 mm. The Mohan 24MV energy spectrum was used as a photon source. The field size was 5cm x 5cm and SSD was 100 cm. The phantom size was 16cm × 16cm × 28cm. The number of histories ranged from 1 to 2 billion. The percentage difference of the dose between the medium with foils and the homogeneous water was computed along the beam axis. The minimum dose enhancement and the change of integrated dose between the foils were determined. Results: Increasing the number of foils resulted in a decrease in the minimum dose enhancement. The highest dose region occurred in the last section for the 4 and 6 foil cases, whereas the 8 and 10 foil configurations showed the maximum dose region towards the center of the foil group. Increasing the number of foils increased the total integrated dose between foils. For example, the total integrated dose increase between the first and the last foils with a 3mm foil separation were 34.2, 43.4, 57.4, and 64.7% for 4, 6, 8 and 10 foils, respectively. Conclusion: This work showed the degree of dose enhancement around multiple thin lead foils. The results suggest that the total attenuation of photon beam can be increased by increasing the number of foils with a fixed total foil thickness.

  8. Performance of Simple Gas Foil Thrust Bearings in Air

    NASA Technical Reports Server (NTRS)

    Bruckner, Robert J.

    2012-01-01

    Foil bearings are self-acting hydrodynamics devices used to support high speed rotating machinery. The advantages that they offer to process fluid lubricated machines include: high rotational speed capability, no auxiliary lubrication system, non-contacting high speed operation, and improved damping as compared to rigid hydrodynamic bearings. NASA has had a sporadic research program in this technology for almost 6 decades. Advances in the technology and understanding of foil journal bearings have enabled several new commercial products in recent years. These products include oil-free turbochargers for both heavy trucks and automobiles, high speed electric motors, microturbines for distributed power generation, and turbojet engines. However, the foil thrust bearing has not received a complimentary level of research and therefore has become the weak link of oil-free turbomachinery. In an effort to both provide machine designers with basic performance parameters and to elucidate the underlying physics of foil thrust bearings, NASA Glenn Research Center has completed an effort to experimentally measure the performance of simple gas foil thrust bearing in air. The database includes simple bump foil supported thrust bearings with full geometry and manufacturing techniques available to the user. Test conditions consist of air at ambient pressure and temperatures up to 500 C and rotational speeds to 55,000 rpm. A complete set of axial load, frictional torque, and rotational speed is presented for two different compliant sub-structures and inter-pad gaps. Data obtained from commercially available foil thrust bearings both with and without active cooling is presented for comparison. A significant observation made possible by this data set is the speed-load capacity characteristic of foil thrust bearings. Whereas for the foil journal bearing the load capacity increases linearly with rotational speed, the foil thrust bearing operates in the hydrodynamic high speed limit. In

  9. CO{sub 2} CAPTURE BY ABSORPTION WITH POTASSIUM CARBONATE

    SciTech Connect

    Gary T. Rochelle; J.Tim Cullinane; Marcus Hilliard; Eric Chen; Babatunde Oyenekan; Ross Dugas

    2005-01-31

    The objective of this work is to improve the process for CO{sub 2} capture by alkanolamine absorption/stripping by developing an alternative solvent, aqueous K{sub 2}CO{sub 3} promoted by piperazine. Thermodynamic modeling predicts that the heat of desorption of CO{sub 2} from 5m K+/2.5 PZ from 85 kJ/mole at 40 C to 30 kJ/mole at 120 C. Mass transfer modeling of this solvent suggests that carbonate and general salt concentration play a major role in catalyzing the rate of reaction of CO{sub 2} with piperazine. Stripper modeling suggests that with the multipressure stripper, the energy consumption with a generic solvent decreases by 15% as the heat of desorption is decreased from 23.8 to 18.5 kcal/gmol. A second pilot plant campaign with 5m K+/2.5 PZ was successfully completed.

  10. A Microfabricated Involute-Foil Regenerator for Stirling Engines

    NASA Technical Reports Server (NTRS)

    Tew, Roy; Ibrahim, Mounir; Danila, Daniel; Simon, Terry; Mantell, Susan; Sun, Liyong; Gedeon, David; Kelly, Kevin; McLean, Jeffrey; Wood, Gary; Qiu, Songgang

    2007-01-01

    A segmented involute-foil regenerator has been designed, microfabricated and tested in an oscillating-flow rig with excellent results. During the Phase I effort, several approximations of parallel-plate regenerator geometry were chosen as potential candidates for a new microfabrication concept. Potential manufacturers and processes were surveyed. The selected concept consisted of stacked segmented-involute-foil disks (or annular portions of disks), originally to be microfabricated from stainless-steel via the LiGA (lithography, electroplating, and molding) process and EDM (electric discharge machining). During Phase II, re-planning of the effort led to test plans based on nickel disks, microfabricated via the LiGA process, only. A stack of nickel segmented-involute-foil disks was tested in an oscillating-flow test rig. These test results yielded a performance figure of merit (roughly the ratio of heat transfer to pressure drop) of about twice that of the 90% random fiber currently used in small 100 W Stirling space-power convertors in the Reynolds Number range of interest (50-100). A Phase III effort is now underway to fabricate and test a segmented-involute-foil regenerator in a Stirling convertor. Though funding limitations prevent optimization of the Stirling engine geometry for use with this regenerator, the Sage computer code will be used to help evaluate the engine test results. Previous Sage Stirling model projections have indicated that a segmented-involute-foil regenerator is capable of improving the performance of an optimized involute-foil engine by 6-9%; it is also anticipated that such involute-foil geometries will be more reliable and easier to manufacture with tight-tolerance characteristics, than random-fiber or wire-screen regenerators. Beyond the near-term Phase III regenerator fabrication and engine testing, other goals are (1) fabrication from a material suitable for high temperature Stirling operation (up to 850 C for current engines; up to

  11. A Microfabricated Involute-Foil Regenerator for Stirling Engines

    NASA Technical Reports Server (NTRS)

    Tew, Roy; Ibrahim, Mounir; Danila, Daniel; Simon, Terrence; Mantell, Susan; Sun, Liyong; Gedeon, David; Kelly, Kevin; McLean, Jeffrey; Qiu, Songgang

    2007-01-01

    A segmented involute-foil regenerator has been designed, microfabricated and tested in an oscillating-flow rig with excellent results. During the Phase I effort, several approximations of parallel-plate regenerator geometry were chosen as potential candidates for a new microfabrication concept. Potential manufacturers and processes were surveyed. The selected concept consisted of stacked segmented-involute-foil disks (or annular portions of disks), originally to be microfabricated from stainless-steel via the LiGA (lithography, electroplating, and molding) process and EDM. During Phase II, re-planning of the effort led to test plans based on nickel disks, microfabricated via the LiGA process, only. A stack of nickel segmented-involute-foil disks was tested in an oscillating-flow test rig. These test results yielded a performance figure of merit (roughly the ratio of heat transfer to pressure drop) of about twice that of the 90 percent random fiber currently used in small approx.100 W Stirling space-power convertors-in the Reynolds Number range of interest (50 to 100). A Phase III effort is now underway to fabricate and test a segmented-involute-foil regenerator in a Stirling convertor. Though funding limitations prevent optimization of the Stirling engine geometry for use with this regenerator, the Sage computer code will be used to help evaluate the engine test results. Previous Sage Stirling model projections have indicated that a segmented-involute-foil regenerator is capable of improving the performance of an optimized involute-foil engine by 6 to 9 percent; it is also anticipated that such involute-foil geometries will be more reliable and easier to manufacture with tight-tolerance characteristics, than random-fiber or wire-screen regenerators. Beyond the near-term Phase III regenerator fabrication and engine testing, other goals are (1) fabrication from a material suitable for high temperature Stirling operation (up to 850 C for current engines; up to 1200 C

  12. Instabilities in foil implosions and the effect of radiation output

    SciTech Connect

    Oona, H.; Peterson, D.L.; Goforth, J.H.

    1995-08-01

    One of the aims of the Athena program at the Los Alamos National Laboratory is the generation of a high fluence of soft x-rays from the thermalization of an radially imploding foil. In the experiments in Athena program, a large axial current is passed through a cylindrical aluminum foil. Under the action of the Lorentz force, the resulting plasma accelerates toward the axis, thermalizes, and produces a fast soft x-ray pulse with a blackbody temperature up to several hundred electron volts. In order that there be the maximum power compression and the highest x-ray fluence and temperature, the plasma stagnation on axis must occur very promptly. This requires that the imploding plasma be as thin and symmetric as possible. A serious problem in the thermalization process is the formation of instabilities in the plasma due to the self-magnetic field that governs the implosion of foil. A large diagnostic effort was developed to capture the details of the implosion and instability growth in several foil implosion experiments. In this report, we will present visible light images and x-ray data designed to study the effects of foil mass, current, and initial perturbations on the instability growth during foil implosion. Representative data is presented from several experiments using the Pegasus capacitor bank system and the explosively driven Procyon system. These experiments are labeled Peg 25 and Peg 33 for the Pegasus experiments and PDD1, PDD2 and PRF0 for the Procyon experiments. In these experiments, all foils had radii of 5 centimeters but varied in mass and initial conditions. Experimental data from several shots were compared with each other and to a radiation magnetohydrodynamic (RMHD) computation and described in a separate paper.

  13. Misalignment in Gas Foil Journal Bearings: An Experimental Study

    NASA Technical Reports Server (NTRS)

    Howard, Samuel A.

    2008-01-01

    As gas foil journal bearings become more prevalent in production machines, such as small gas turbine propulsion systems and microturbines, system-level performance issues must be identified and quantified in order to provide for successful design practices. Several examples of system-level design parameters that are not fully understood in foil bearing systems are thermal management schemes, alignment requirements, balance requirements, thrust load balancing, and others. In order to address some of these deficiencies and begin to develop guidelines, this paper presents a preliminary experimental investigation of the misalignment tolerance of gas foil journal bearing systems. Using a notional gas foil bearing supported rotor and a laser-based shaft alignment system, increasing levels of misalignment are imparted to the bearing supports while monitoring temperature at the bearing edges. The amount of misalignment that induces bearing failure is identified and compared to other conventional bearing types such as cylindrical roller bearings and angular contact ball bearings. Additionally, the dynamic response of the rotor indicates that the gas foil bearing force coefficients may be affected by misalignment.

  14. Iridium and tantalum foils for spaceflight neutron dosimetry.

    NASA Technical Reports Server (NTRS)

    English, R. A.; Liles, E. D.

    1972-01-01

    Description of a two-foil system of iridium and tantalum which can measure thermal and intermediate energy neutrons at flux densities of 1 neutron/sq cm-sec over a ten-day lunar mission (1,000,000 neutrons/sq cm). The foils are chemically inert and nontoxic, weigh less than 1 g each, and require only routine gamma pulse height analysis for activation measurement. Detection of fluences below 1,000,000 neutrons/sq cm are achieved for counts of foil activity made as late as two months following neutron exposure. Tantalum foils flown in Apollo 11 indicated a mean dose equivalent to the astronauts of less than 16 mrem from thermal plus intermediate energy neutrons, while nuclear emulsion track analysis indicated approximately 17 mrem from neutrons of energy greater than 0.6 MeV. Iridium foils flown on Apollo 12 indicated dose equivalents of 1.8 to 2.8 mrem from thermal neutrons, excluding tissue thermalized SNAP-27 neutrons.

  15. Gas Foil Bearings for Space Propulsion Nuclear Electric Power Generation

    NASA Technical Reports Server (NTRS)

    Howard, Samuel A.; DellaCorte, Christopher

    2006-01-01

    The choice of power conversion technology is critical in directing the design of a space vehicle for the future NASA mission to Mars. One candidate design consists of a foil bearing supported turbo alternator driven by a helium-xenon gas mixture heated by a nuclear reactor. The system is a closed-loop, meaning there is a constant volume of process fluid that is sealed from the environment. Therefore, foil bearings are proposed due to their ability to use the process gas as a lubricant. As such, the rotor dynamics of a foil bearing supported rotor is an important factor in the eventual design. The current work describes a rotor dynamic analysis to assess the viability of such a system. A brief technology background, assumptions, analyses, and conclusions are discussed in this report. The results indicate that a foil bearing supported turbo alternator is possible, although more work will be needed to gain knowledge about foil bearing behavior in helium-xenon gas.

  16. Flapping Instability of Two Tandem Flexible Foils in Uniform Axial Flow

    NASA Astrophysics Data System (ADS)

    Gurugubelli, Pardha Saradhi; Jaiman, Rajeev Kumar; Chua, Cassey

    2015-11-01

    We present a numerical analysis on the stability and coupled dynamics of two tandem flexible foils clamped at their leading edges in a uniform axial flow. The flexible foils considered for this study correspond to the fixed-point stable regime of the single flexible foil where the flexible foil aligns itself in the flow direction with no significant trailing edge oscillations. A high-order nonlinear coupled solver based on the variational formulation has been considered for analyzing the effects of gap between the foils on the stability and coupled behaviour of both the upstream and downstream foils. As a function of decreasing gap, it is observed that the tandem foil configuration is more prone to flapping instability than its single flexible foil counterpart. The evolution of the instability for the downstream foil shows two distinct dynamical scenarios: (i) only the downstream foil exhibits flapping motion and (ii) both the upstream and the downstream foils perform flapping. With the aid of a rigid foil in the upstream of a flexible foil, we further present a detailed analysis on the effects of the upstream wake and vortex shedding on the stability and flapping dynamics of the downstream foil.

  17. Nanowire LEDs grown directly on flexible metal foil

    NASA Astrophysics Data System (ADS)

    May, Brelon J.; Sarwar, A. T. M. Golam; Myers, Roberto C.

    2016-04-01

    Using molecular beam epitaxy, self-assembled AlGaN nanowires are grown directly on Ta and Ti foils. Scanning electron microscopy shows that the nanowires are locally textured with the underlying metallic grains. Photoluminescence spectra of GaN nanowires grown on metal foils are comparable to GaN nanowires grown on single crystal Si wafers. Similarly, photoluminescence lifetimes do not vary significantly between these samples. Operational AlGaN light emitting diodes are grown directly on flexible Ta foil with an electroluminescence peak emission of ˜350 nm and a turn-on voltage of ˜5 V. These results pave the way for roll-to-roll manufacturing of solid state optoelectronics.

  18. Laser shock microforming of aluminum foil with fs laser

    NASA Astrophysics Data System (ADS)

    Ye, Yunxia; Feng, Yayun; Xuan, Ting; Hua, Xijun; Hua, Yinqun

    2014-12-01

    Laser shock microforming of Aluminum(Al) foil through fs laser has been researched in this paper. The influences of confining layer, clamping method and impact times on induced dent depths were investigated experimentally. Microstructure of fs laser shock forming Al foil was observed through Transmission electron microscopy (TEM). Under the condition of tightly clamping, the dent depths increase with impact times and finally tend to saturating. Another new confining layer, the main component of which is polypropylene, was applied and the confining effect of it is better because of its higher impedance. TEM results show that dislocation is one of the main deformation mechanisms of fs laser shock forming Al foil. Specially, most of dislocations exist in the form of short and discrete dislocation lines. Parallel straight dislocation slip line also were observed. We analyzed that these unique dislocation arrangements are due to fs laser-induced ultra high strain rate.

  19. Model-Based Optimization for Flapping Foil Actuation

    NASA Astrophysics Data System (ADS)

    Izraelevitz, Jacob; Triantafyllou, Michael

    2014-11-01

    Flapping foil actuation in nature, such as wings and flippers, often consist of highly complex joint kinematics which present an impossibly large parameter space for designing bioinspired mechanisms. Designers therefore often build a simplified model to limit the parameter space so an optimum motion trajectory can be experimentally found, or attempt to replicate exactly the joint geometry and kinematics of a suitable organism whose behavior is assumed to be optimal. We present a compromise: using a simple local fluids model to guide the design of optimized trajectories through a succession of experimental trials, even when the parameter space is too large to effectively search. As an example, we illustrate an optimization routine capable of designing asymmetric flapping trajectories for a large aspect-ratio pitching and heaving foil, with the added degree of freedom of allowing the foil to move parallel to flow. We then present PIV flow visualizations of the optimized trajectories.

  20. Dynamics of a heaving flexible foil in a uniform flow

    NASA Astrophysics Data System (ADS)

    Paraz, Florine; Eloy, Christophe; Schouveiler, Lionel

    2012-11-01

    Most aerial and aquatic animals produce thrust using flapping flexible appendages. The performances of such propulsion systems are strongly related to the appendages dynamics, in particular to the amplitude of the trailing edge motion and to the vortical patterns produced. A better understanding of this mode of propulsion requires to investigate the dynamics of the flexible appendages, as a response to harmonic forcing. In this context, experiments are performed with flexible foils immersed in the uniform flow of a water channel. A harmonic heaving motion, that is transverse to the foil, is then imposed to its leading edge. The response of the foil likely results from the resonance between the forcing and the natural modes of vibration. Experimental results are compared with a two-dimensional model assuming a zero-thickness flexible sheet of infinite span immersed in a potential flow.

  1. An experimental and theoretical study of structural damping in compliant foil bearings

    NASA Technical Reports Server (NTRS)

    Ku, C.-P. Roger

    1994-01-01

    This paper describes an experimental investigation into the dynamic characteristics of corrugated foil (bump foil) strips used in compliant surface foil bearings. This study provided and opportunity to quantify the structural damping of bump foil strips. The experimental data were compared to results obtained by a theoretical model developed earlier. The effects of bearing design parameters, such as static loads, dynamic displacement amplitudes, bump configurations, pivot locations, surface coatings, and lubricant were also evaluated. An understanding of the dynamic characteristics of bump foil strips resulting from this work offers designers a means for enhancing the design of high-performance compliant foil bearings.

  2. High Temperature Performance Evaluation of a Compliant Foil Seal

    NASA Technical Reports Server (NTRS)

    Salehi, Mohsen; Heshmat, Hooshang; Walton, James F., II

    2001-01-01

    The key points to be gleaned from the effort reported herein are that the CFS (Compliant Foil Seal) has been demonstrated in conjunction with a foil bearing in a small gas turbine simulator at temperatures as high as 1000 F and outperformed a comparable brush seal. Having demonstrated the feasibility of the CFS, it would appear that this new seal design has application potential in a wide range of machines. What remains is to demonstrate performance at higher pressure ratios, consistent performance at large rotor excursions and the ability to manufacture the seal in much larger sizes exceeding by an order of magnitude that which has been tested to date.

  3. Effect of Smoked Foil Thickness and Location on Detonation Initiation

    NASA Astrophysics Data System (ADS)

    Chung, K. M.; Wen, C. S.

    Smoked foil has been employed to visualize triple point pattern (or cell width), indicating detonation phenomena. However, the aluminum sheet also corresponds to sudden contraction in a smooth tube. It might induce early trigger on detonation initiation and result in a reduction in deflagration-to-detonation transition (DDT) run-up distance. Test results showed the thickness of aluminum sheet of less than 1.3 mm is required to eliminate the effect of smoked foil. A reduction in Xdtt is observed when the thickness of aluminum sheet increases.

  4. Method and apparatus for tensile testing of metal foil

    NASA Technical Reports Server (NTRS)

    Wade, O. W. (Inventor)

    1976-01-01

    A method for obtaining accurate and reproducible results in the tensile testing of metal foils in tensile testing machines is described. Before the test specimen are placed in the machine, foil side edges are worked until they are parallel and flaw free. The specimen are also aligned between and secured to grip end members. An aligning apparatus employed in the method is comprised of an alignment box with a longitudinal bottom wall and two upright side walls, first and second removable grip end members at each end of the box, and a means for securing the grip end members within the box.

  5. Electrochemically replicated smooth aluminum foils for anodic alumina nanochannel arrays.

    PubMed

    Biring, Sajal; Tsai, Kun-Tong; Sur, Ujjal Kumar; Wang, Yuh-Lin

    2008-01-01

    A fast electrochemical replication technique has been developed to fabricate large-scale ultra-smooth aluminum foils by exploiting readily available large-scale smooth silicon wafers as the masters. Since the adhesion of aluminum on silicon depends on the time of surface pretreatment in water, it is possible to either detach the replicated aluminum from the silicon master without damaging the replicated aluminum and master or integrate the aluminum film to the silicon substrate. Replicated ultra-smooth aluminum foils are used for the growth of both self-organized and lithographically guided long-range ordered arrays of anodic alumina nanochannels without any polishing pretreatment. PMID:21730530

  6. Surface plasma wave excitation via laser irradiated overdense plasma foil

    SciTech Connect

    Kumar, Pawan; Tripathi, V. K.

    2012-04-09

    A laser irradiated overdense plasma foil is seen to be susceptible to parametric excitation of surface plasma wave (SPW) and ion acoustic wave (IAW) on the ion plasma period time scale. The SPW is localised near the front surface of the foil while IAW extends upto the rear. The evanescent laser field and the SPW exert a ponderomotive force on electrons driving the IAW. The density perturbation associated with the latter beats with the laser induced oscillatory electron velocity to drive the SPW. At relativistic laser intensity, the growth rate is of the order of ion plasma frequency.

  7. Use of sputtered zinc oxide film on aluminium foil substrate to produce a flexible and low profile ultrasonic transducer.

    PubMed

    Hou, Ruozhou; Fu, Yong Qing; Hutson, David; Zhao, Chao; Gimenez, Esteban; Kirk, Katherine J

    2016-05-01

    A flexible and low profile ultrasonic transducer was fabricated for non-destructive testing (NDT) applications by DC sputtering of 3 μm thick, c-axis oriented, ZnO film on 50 μm aluminium foil. Due to the thin foil-based construction, the transducer can be applied to curved objects and used in sites of restricted accessibility. The device has been used to demonstrate detection of simulated defects in a 45 mm diameter steel pipe, and for thickness measurement on a 3.1 mm thick flat carbon steel plate. Centre frequency measured on the flat plate was 24-29 MHz, with -6 dB bandwidth 4-7 MHz. The pulse duration depended on the couplant, at best 3 cycles or 0.12 μs using SONO Ultragel or epoxy couplant. Transducer performance was found to be comparable to a commercial 10 MHz piezoelectric ultrasonic transducer. PMID:26913377

  8. Spectral content of buried Ag foils at 10(16) W/cm(2) laser illumination.

    PubMed

    Huntington, C M; Maddox, B R; Park, H-S; Prisbrey, S; Remington, B A

    2014-11-01

    Sources of 5-12 keV thermal Heα x-rays are readily generated by laser irradiation of mid-Z foils at intensities >10(14) W/cm(2), and are widely used as probes for inertial confinement fusion and high-energy-density experiments. Higher energy 17-50 keV x-ray sources are efficiently produced from "cold" Kα emission using short pulse, petawatt lasers at intensities >10(18) W/cm(2) [H.-S. Park, B. R. Maddox et al., "High-resolution 17-75 keV backlighters for high energy density experiments," Phys. Plasmas 15(7), 072705 (2008); B. R. Maddox, H. S. Park, B. A. Remington et al., "Absolute measurements of x-ray backlighter sources at energies above 10 keV," Phys. Plasmas 18(5), 056709 (2011)]. However, when long pulse (>1 ns) lasers are used with Z > 30 elements, the spectrum contains contributions from both K shell transitions and from ionized atomic states. Here we show that by sandwiching a silver foil between layers of high-density carbon, the ratio of Kα:Heα in the x-ray spectrum is significant increased over directly illuminated Ag foils, with narrower lines from K-shell transitions. Additionally, the emission volume is more localized for the sandwiched target, producing a more planar x-ray sheet. This technique may be useful for generating probes requiring spectral purity and a limited spatial extent, for example, in incoherent x-ray Thomson scattering experiments. PMID:25430207

  9. Spectral content of buried Ag foils at 1016 W/cm2 laser illuminationa)

    NASA Astrophysics Data System (ADS)

    Huntington, C. M.; Maddox, B. R.; Park, H.-S.; Prisbrey, S.; Remington, B. A.

    2014-11-01

    Sources of 5-12 keV thermal Heα x-rays are readily generated by laser irradiation of mid-Z foils at intensities >1014 W/cm2, and are widely used as probes for inertial confinement fusion and high-energy-density experiments. Higher energy 17-50 keV x-ray sources are efficiently produced from "cold" Kα emission using short pulse, petawatt lasers at intensities >1018 W/cm2 [H.-S. Park, B. R. Maddox et al., "High-resolution 17-75 keV backlighters for high energy density experiments," Phys. Plasmas 15(7), 072705 (2008); B. R. Maddox, H. S. Park, B. A. Remington et al., "Absolute measurements of x-ray backlighter sources at energies above 10 keV," Phys. Plasmas 18(5), 056709 (2011)]. However, when long pulse (>1 ns) lasers are used with Z > 30 elements, the spectrum contains contributions from both K shell transitions and from ionized atomic states. Here we show that by sandwiching a silver foil between layers of high-density carbon, the ratio of Kα:Heα in the x-ray spectrum is significant increased over directly illuminated Ag foils, with narrower lines from K-shell transitions. Additionally, the emission volume is more localized for the sandwiched target, producing a more planar x-ray sheet. This technique may be useful for generating probes requiring spectral purity and a limited spatial extent, for example, in incoherent x-ray Thomson scattering experiments.

  10. H Ly-alpha transmittance of thin foils of C, Si/C, and Al/C for keV particle detectors

    NASA Technical Reports Server (NTRS)

    Drake, V. A.; Sandel, B. R.; Jenkins, D. G.; Hsieh, K. C.

    1992-01-01

    A class of instruments designed for remote sensing of space plasmas by measuring energetic neutral atoms (ENA) uses a thin foil as both a signal generator and a light shield. An ENA imager must look directly at the ENA source region, which is also usually an intense source of H Ly-alpha (1216 A) photons. It is desirable to minimize the energy threshold for ENA detectors, at the same time maximizing the blocking of H Ly-alpha. Optimizing filter design to meet these two contrary requirements has led us to measure the transmittance of thin C, Si/C, and Al/C foils at H Ly-alpha. Our results indicate that (1) transmittance of less than 0.0007 can be achieved with 7 micro-g/sq cm Si on 1.7 micro-g/sq cm C; (2) an Si/C composite foil with a thin carbon layer is more effective in blocking UV radiation while having the lowest energy threshold of all the foils measured; and (3) transmittance of Si/C foils of known Si and C thicknesses cannot be accurately predicted, but must be measured.

  11. Mirror symmetric optics design for charge-stripping section in Rare Isotope Science Project

    NASA Astrophysics Data System (ADS)

    Kim, Hye-Jin; Kim, Hyung-Jin; Jeon, Dong-O.; Hwang, Ji-Gwang; Kim, Eun-San

    2013-12-01

    The main aim of the Rare Isotope Science Project is to construct a high power heavy-ion accelerator based on the superconducting linear accelerator (SCL). The heavy ion accelerator is a key research facility that will allow ground-breaking research into numerous facets of basic science, such as nuclear physics, astrophysics, atomic physics, life science, medicine and material science. The machine will provide a beam power of 400 kW with a 238U79+ beam of 8 pμA and 200 MeV/u. One of the critical components in the SCL is the charge stripper between the two segments, SCL1 and SCL2, of the SCL. The charge stripper removes electrons from the ion beams to enhance the acceleration efficiency in the subsequent SCL2. To improve the efficiency of acceleration and power in SCL2, the optimal energy of stripped ions in a solid carbon foil stripper was estimated using the code LISE++. The thickness of the solid carbon foil was 300 μg/m2. The charge stripping efficiency of the solid carbon stripper in the present study was approximately 87%. For charge selection from the ions produced by the solid carbon stripper, a dispersive section is needed down-stream of the foil. The designed optics for the dispersive section is based on the mirror-symmetric optics to minimize the effect of high-order aberrations.

  12. Design, Fabrication and Performance of Open Source Generation I and II Compliant Hydrodynamic Gas Foil Bearings

    NASA Technical Reports Server (NTRS)

    DellaCorte, Christopher; Radil, Kevin C.; Bruckner, Robert J.; Howard, S. Adam

    2007-01-01

    Foil gas bearings are self-acting hydrodynamic bearings made from sheet metal foils comprised of at least two layers. The innermost top foil layer traps a gas pressure film that supports a load while a layer or layers underneath provide an elastic foundation. Foil bearings are used in many lightly loaded, high-speed turbo-machines such as compressors used for aircraft pressurization, and small micro-turbines. Foil gas bearings provide a means to eliminate the oil system leading to reduced weight and enhanced temperature capability. The general lack of familiarity of the foil bearing design and manufacturing process has hindered their widespread dissemination. This paper reviews the publicly available literature to demonstrate the design, fabrication and performance testing of both first and second generation bump style foil bearings. It is anticipated that this paper may serve as an effective starting point for new development activities employing foil bearing technology.

  13. Energy harvesting through flow-induced oscillations of a foil

    NASA Astrophysics Data System (ADS)

    Peng, Zhangli; Zhu, Qiang

    2009-12-01

    By using a Navier-Stokes model, we examine a novel flow energy harvesting device consisting of a flapping foil mounted on a damper (representing the power generator) and a rotational spring. Self-induced and self-sustained flapping motions, including a heaving motion h(t ) and a pitching motion α(t ), are excited by an incoming flow and power extraction is achieved from the heaving response. Depending upon the configuration of the system and the mechanical parameters (e.g., the location of the pitching axis and the stiffness of the rotational spring), four different responses are recorded: (i) the foil remains stable in its initial position (α =0 and h =0); (ii) periodic pitching (around α =0) and heaving motions are excited; (iii) the foil undergoes irregular motions characterized by switching between oscillations around two pitching angles; and (iv) the foil rotates to a position with an angle to the incoming flow and oscillates around it. The existence of response (ii) suggests the feasibility of controllable and stable flow energy extraction by this device. Through numerical simulations with a Navier-Stokes model we have determined combinations of geometric and mechanical parameters to achieve this response. The corresponding energy harvesting capacity and efficiency are predicted.

  14. Tribalism as a Foiled Factor of Africa Nation-Building

    ERIC Educational Resources Information Center

    Okogu, J. O.; Umudjere, S. O.

    2016-01-01

    This paper tends to examine tribalism as a foiled factor on Africa nation-building and proffers useful tips to salvaging the Africa land from this deadly social problem. Africans in times past had suffered enormous attacks, injuries, losses, deaths, destruction of properties and human skills and ideas due to the presence of tribalistic views in…

  15. The Visualization of Infrared Radiation Using Thermal Sensitive Foils

    ERIC Educational Resources Information Center

    Bochnícek, Zdenek

    2013-01-01

    This paper describes a set of demonstration school experiments where infrared radiation is detected using thermal sensitive foils. The possibility of using standard glass lenses for infrared imaging is discussed in detail. It is shown that with optic components made from glass, infrared radiation up to 2.5 µm of wavelength can be detected. The…

  16. Using Aluminum Foil to Record Structures in Sedimentary Rock.

    ERIC Educational Resources Information Center

    Metz, Robert

    1982-01-01

    Aluminum foil can be used to make impressions of structures preserved in sedimentary rock. The impressions can be projected onto a screen, photographed, or a Plaster of Paris model can be made from them. Impressions of ripple marks, mudcracks, and raindrop impressions are provided in photographs illustrating the technique. (Author/JN)

  17. Laser-induced structure formation on stretched polymer foils

    SciTech Connect

    Bityurin, Nikita; Arnold, Nikita; Baeuerle, Dieter; Arenholz, Enno

    2007-04-15

    Noncoherent structures that develop during UV laser ablation of stretched semicrystalline polymer foils are a very general phenomenon. A thermodynamic model based on stress relaxation within the modified layer of the polymer surface describes the main features of the observed phenomena, and, in particular, the dependence of the period of structures on laser wavelength, fluence, and number of laser pulses.

  18. Foil Bearing Starting Considerations and Requirements for Rotorcraft Engine Applications

    NASA Technical Reports Server (NTRS)

    Radil, Kevin C.; DellaCorte, Christopher

    2009-01-01

    Foil gas bearings under development for rotorcraft-sized, hot core engine applications have been susceptible to damage from the slow acceleration and rates typically encountered during the pre-ignition stage in conventional engines. Recent laboratory failures have been assumed to be directly linked to operating foil bearings below their lift-off speed while following conventional startup procedures for the engines. In each instance, the continuous sliding contact between the foils and shaft was believed to thermally overload the bearing and cause the engines to fail. These failures highlight the need to characterize required acceleration rates and minimum operating speeds for these applications. In this report, startup experiments were conducted with a large, rotorcraft engine sized foil bearing under moderate load and acceleration rates to identify the proper start procedures needed to avoid bearing failure. The results showed that a bearing under a 39.4 kPa static load can withstand a modest acceleration rate of 500 rpm/s and excessive loitering below the bearing lift-off speed provided an adequate solid lubricant is present.

  19. Validation of calculated self-shielding factors for Rh foils

    NASA Astrophysics Data System (ADS)

    Jaćimović, R.; Trkov, A.; Žerovnik, G.; Snoj, L.; Schillebeeckx, P.

    2010-10-01

    Rhodium foils of about 5 mm diameter were obtained from IRMM. One foil had thickness of 0.006 mm and three were 0.112 mm thick. They were irradiated in the pneumatic transfer system and in the carousel facility of the TRIGA reactor at the Jožef Stefan Institute. The foils were irradiated bare and enclosed in small cadmium boxes (about 2 g weight) of 1 mm thickness to minimise the perturbation of the local neutron flux. They were co-irradiated with 5 mm diameter and 0.2 mm thick Al-Au (0.1%) alloy monitor foils. The resonance self-shielding corrections for the 0.006 and 0.112 mm thick samples were calculated by the Monte Carlo simulation and amount to about 10% and 60%, respectively. The consistency of measurements confirmed the validity of self-shielding factors. Trial estimates of Q0 and k0 factors for the 555.8 keV gamma line of 104Rh were made and amount to 6.65±0.18 and (6.61±0.12)×10 -2, respectively.

  20. Characterization of thin-foil ultracold neutron detectors

    NASA Astrophysics Data System (ADS)

    Sallaska, A. L.; Hoedl, S.; Garcia, A.; Melconian, D.; Young, A. R.; Geltenbort, P.; Sjue, S. K. L.; Holley, A. T.

    2009-05-01

    We have fabricated ultracold neutron detectors that consist of silicon charged particle detectors coupled with thin nickel foils coated with either natural LiF or 10B implanted into vanadium. The foils convert neutrons into energetic, readily detectable, charged particles which are in turn detected by silicon detectors. The detectors were tested at the Institut Laue-Langevin with a gravitational spectrometer. From a rigorous Monte Carlo simulation of the experiment, the minimum detection cutoff velocities (effective potentials) were determined to be 309±17 cm/s ( 49.8±2.7 neV) for LiF and 367±39 cm/s ( 70.3±7.5 neV) for 10B/V. Although the result for LiF is consistent with expectations, the result for 10B/V is significantly higher. We interpret this discrepancy as due to contamination. We also show that while a thicker foil is more efficient for ultracold neutron detection, a thinner foil is more ideal for determining the cutoff velocity.

  1. Secret in the Margins: Rutherford's Gold Foil Experiment

    ERIC Educational Resources Information Center

    Aydin, Sevgi; Hanuscin, Deborah L.

    2011-01-01

    In this article, the authors describe a lesson that uses the 5E Learning Cycle to help students not only understand the atomic model but also how Ernest Rutherford helped develop it. The lesson uses Rutherford's gold foil experiment to focus on three aspects of the nature of science: the empirical nature of science, the tentativeness of scientific…

  2. Proton acceleration from short pulse lasers interacting with ultrathin foil

    NASA Astrophysics Data System (ADS)

    Petrov, George; McGuffey, Christopher; Thomas, Alec; Krushelnick, Karl; Beg, Farhat

    2015-11-01

    Two-dimensional particle-in-cell simulations using 50 nm Si3N4 and DLC foils are compared to published experimental data of proton acceleration from ultra-thin foils (<1 μm) irradiated by short pulse lasers (30-50 fs), and some underlying physics issues pertinent to proton acceleration have been addressed. 2D particle-in-cell simulations show that the maximum proton energy scales as I2/3, stronger than Target Normal Sheath Acceleration for thick foils (>1 μm), which is typically between I1/3 and I1/2. Published experimental data were found to depend primarily on the laser energy and scale as E2/3. The different scaling laws for thick (>1 μm) and ultra-thin (<1 μm) foils are explained qualitatively as transitioning from Target Normal Sheath Acceleration to more advanced acceleration schemes such as Radiation-Induced Transparency and Radiation Pressure Acceleration regimes. This work was performed with the support of the Air Force Office of Scientific Research under grant FA9550-14-1-0282.

  3. Modified Monkman-Grant relationship for austenitic stainless steel foils

    NASA Astrophysics Data System (ADS)

    Osman Ali, Hassan; Tamin, Mohd Nasir

    2013-02-01

    Characteristics of creep deformation for austenitic stainless steel foils are examined using the modified Monkman-Grant equation. A series of creep tests are conducted on AISI 347 steel foils at 700 °C and different stress levels ranging from 54 to 221 MPa. Results showed that at lower stress levels below 110 MPa, the creep life parameters ɛ, ɛr, tr can be expressed using the modified Monkman-Grant equation with exponent m'= 0.513. This indicates significant deviation of the creep behavior from the first order reaction kinetics theory for creep (m' = 1.0). The true tertiary creep damage in AISI 347 steel foil begins after 65.9% of the creep life of the foil has elapsed at stress levels above 150 MPa. At this high stress levels, Monkman-Grant ductility factor λ' saturates to a value of 1.3 with dislocation-controlled deformation mechanisms operating. At low stress levels, λ' increases drastically (λ'=190 at 54 MPa) when slow diffusion-controlled creep is dominant.

  4. Foil bearing performance in liquid nitrogen and liquid oxygen

    NASA Technical Reports Server (NTRS)

    Genge, Gary G.; Saville, Marshall; Gu, Alston

    1993-01-01

    Space transfer vehicles and other power and propulsion systems require long-life turbopumps. Rolling-element bearings used in current turbopumps do not have sufficient life for these applications. Process fluid foil bearings have established long life, with exceptional reliability, over a wide range of temperatures and fluids in many high-speed turbomachinery applications. However, actual data on bearing performance in cryogenic fluids has been minimal. The National Aeronautics and Space Administration (NASA) and AlliedSignal Aerospace Systems and Equipment (ASE) have attempted to characterize the leaf-type compliant foil bearing in oxygen and nitrogen. The work performed under a joint internal research and development program between Marshall Space Flight Center (MSFC) and ASE demonstrated that the foil bearing has load capacities of at least 266 psi in liquid oxygen and 352 psi in liquid nitrogen. In addition, the bearing demonstrated a direct damping coefficient of 40 to 50 lb-sec/in. with a damping ratio of .7 to 1.4 in. liquid nitrogen using a bearing sized for upper-stage turbopumps. With the results from this testing and the years of successful use in air cycle machines and other applications, leaf-type compliant foil bearings are ready for testing in liquid oxygen turbopumps.

  5. Evaluation of Alumina-Forming Austenitic Foil for Advanced Recuperators

    SciTech Connect

    Pint, Bruce A; Brady, Michael P; Yamamoto, Yukinori; Santella, Michael L; Maziasz, Philip J; Matthews, Wendy

    2011-01-01

    A corrosion- and creep-resistant austenitic stainless steel has been developed for advanced recuperator applications. By optimizing the Al and Cr contents, the alloy is fully austenitic for creep strength while allowing the formation of a chemically stable external alumina scale at temperatures up to 900 C. An alumina scale eliminates long-term problems with the formation of volatile Cr oxy-hydroxides in the presence of water vapor in exhaust gas. As a first step in producing foil for primary surface recuperators, three commercially cast heats have been rolled to 100 m thick foil in the laboratory to evaluate performance in creep and oxidation testing. Results from initial creep testing are presented at 675 C and 750 C, showing excellent creep strength compared with other candidate foil materials. Laboratory exposures in humid air at 650 800 C have shown acceptable oxidation resistance. A similar oxidation behavior was observed for sheet specimens of these alloys exposed in a modified 65 kW microturbine for 2871 h. One composition that showed superior creep and oxidation resistance has been selected for the preparation of a commercial batch of foil. DOI: 10.1115/1.4002827

  6. Large deflection analysis of a tension-foil bearing

    NASA Technical Reports Server (NTRS)

    Elrod, David A.

    1996-01-01

    The rolling element bearings (REB's) which support many turbomachinery rotors offer high load capacity, low power requirements, and durability. Two disadvantages of REB's are as follows: rolling or sliding contact within the bearing has life-limiting consequences; and REB's provide essentially no damping. The REB's in the Space Shuttle Main Engine (SSME) turbopumps must sustain high static and dynamic loads, at high speeds, with a cryogenic fluid as lubricant and coolant. The pump end ball bearings limit the life of the SSME high pressure oxygen turbopump (HPOTP). Compliant foil bearing (CFB) manufacturers have proposed replacing turbopump REB's with CFB's. CFB's work well in aircraft air cycle machines, auxiliary power units, and refrigeration compressors. In a CFB, the rotor only contacts the foil support structure during start up and shut down. CFB damping is higher than REB damping. However, the load capacity of the CFB is low, compared to a REB. Furthermore, little stiffness and damping data exist for the CFB. A rotordynamic analysis for turbomachinery critical speeds and stability requires the input of bearing stiffness and damping coefficients. The two basic types of CFB are the tension-dominated bearing and the bending-dominated bearing. Many investigators have analyzed and measured characteristics of tension-dominated foil bearings, which are applied principally in magnetic tape recording. The bending-dominated CFB is used more in rotating machinery. Recently, a new tension-foil bearing configuration has been proposed for turbomachinery applications.

  7. 21 CFR 189.301 - Tin-coated lead foil capsules for wine bottles.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Tin-coated lead foil capsules for wine bottles... Addition to Human Food Through Food-Contact Surfaces § 189.301 Tin-coated lead foil capsules for wine bottles. (a) Tin-coated lead foil is composed of a lead foil coated on one or both sides with a thin...

  8. Ink-jet printed colorimetric gas sensors on plastic foil

    NASA Astrophysics Data System (ADS)

    Courbat, Jerome; Briand, Danick; de Rooij, Nico F.

    2010-08-01

    An all polymeric colorimetric gas sensor with its associated electronics for ammonia (NH3) detection targeting low-cost and low-power applications is presented. The gas sensitive layer was inkjet printed on a plastic foil. The use of the foil directly as optical waveguide simplified the fabrication, made the device more cost effective and compatible with large scale fabrication techniques, such as roll to roll processes. Concentrations of 500 ppb of NH3 in nitrogen with 50% of RH were measured with a power consumption of about 868 μW in an optical pulsed mode of operation. Such sensors foresee applications in the field of wireless systems, for environmental and safety monitoring. The fabrication of the planar sensor was based on low temperature processing. The waveguide was made of PEN or PET foil and covered with an ammonia sensitive layer deposited by inkjet printing, which offered a proper and localized deposition of the film. The influence of the substrate temperature and its surface pretreatment were investigated to achieve the optimum deposition parameters for the printed fluid. To improve the light coupling from the light source (LED) to the detectors (photodiodes), polymeric micro-mirrors were patterned in an epoxy resin. With the printing of the colorimetric film and additive patterning of polymeric micro-mirrors on plastic foil, a major step was achieved towards the implementation of full plastic selective gas sensors. The combination with printed OLED and PPD would further lead to an integrated all polymeric optical transducer on plastic foil fully compatible with printed electronics processes.

  9. Improvements in Fabrication of Elastic Scattering Foils Used to Measure Neutron Yield by the Magnetic Recoil Spectrometer

    DOE PAGESBeta

    Reynolds, H. G.; Schoff, M. E.; Farrell, M. P.; Gatu Johnson, M.; Bionta, R. M.; Frenje, J. A.

    2016-08-01

    The magnetic recoil spectrometer uses a deuterated polyethylene polymer (CD2) foil to measure neutron yield in inertial confinement fusion experiments. Higher neutron yields in recent experiments have resulted in primary signal saturation in the detector CR-39 foils, necessitating the fabrication of thinner CD2 foils than established methods could provide. A novel method of fabricating deuterated polymer foils is described. The resulting foils are thinner, smoother, and more uniform in thickness than the foils produced by previous methods. Here, these new foils have successfully been deployed at the National Ignition Facility, enabling higher neutron yield measurements than previous foils, with nomore » primary signal saturation.« less

  10. Terahertz radiation generation by nonlinear mixing of two laser beams over a thin foil

    NASA Astrophysics Data System (ADS)

    Chauhan, Santosh; Parashar, J.

    2015-07-01

    Terahertz radiation generation via nonlinear mixing of two laser beams incident over a thin metal foil is explored. The lasers exert a ponderomotive force on the electrons of metal foil at beat frequency which lies in the terahertz range. The metal foil acts as antenna, producing terahertz radiations, highly directional in nature.

  11. Terahertz radiation generation by nonlinear mixing of two laser beams over a thin foil

    SciTech Connect

    Chauhan, Santosh; Parashar, J.

    2015-07-31

    Terahertz radiation generation via nonlinear mixing of two laser beams incident over a thin metal foil is explored. The lasers exert a ponderomotive force on the electrons of metal foil at beat frequency which lies in the terahertz range. The metal foil acts as antenna, producing terahertz radiations, highly directional in nature.

  12. Candidate alloys for cost-effective, high-efficiency, high-temperature compact/foil heat-exchangers

    SciTech Connect

    Evans, Neal D; Maziasz, Philip J; Shingledecker, John P; Pint, Bruce A; Yamamoto, Yukinori

    2007-01-01

    Solid oxide fuel cell (SOFC) and molten carbonate fuel cell (MCFC) systems operate at high temperatures (up to 1000 C and 650 C, respectively), which makes them especially attractive sources for combined heat and power (CHP) cogeneration. However, improvements in the efficiency of heat exchange in these fuel cells require both development and careful processing of advanced cost-effective alloys for use in such high-temperature service conditions. The high-temperature properties of both sheet and foil forms of several alloys being considered for use in compact heat-exchangers (recuperators) have been characterized. Mechanical and creep-rupture testing, oxidation studies, and microstructural studies have been performed on commercially available sheet and foil forms of alloy 347, alloys 625, HR230, HR120, and the new AL20-25+Nb. These studies have led to a mechanistic understanding of the responses of these alloys to anticipated service conditions, and suggest that these alloys developed for gas- and micro-turbine recuperator applications are also suitable for use in fuel cell heat-exchangers. Additional work is still required to achieve foil forms with creep life comparable to thicker-section wrought product forms of the same alloys.

  13. Satellite and Opacity Effects on Resonance Line Shapes Produced from Short-Pulse Laser Heated Foils

    SciTech Connect

    Shepherd, R; Audebert, P; Chen, H-K; Fournier, K B; Peyreusse, O; Moon, S; Lee, R W; Price, D; Klein, L; Gauthier, J C; Springer, P

    2002-12-03

    We measure the He-like, time-resolved emission from thin foils consisting of 250 {angstrom} of carbon-250 {angstrom} of aluminum and 500 {angstrom} aluminum illuminated with a 150 fs laser pulse at an intensity of 1 x 10{sup 19} W/cm{sup 2}. Dielectronic satellite contributions to the 1s{sup 2}-1s2p({sup 1}P), 1s{sup 2}-1s3p({sup 1}P), and 1s{sup 2}1s4p({sup 1}P) line intensities are modeled using the configuration averaged code AVERROES and is found to be significant for all three resonance lines. The contribution of opacity broadening is inferred from the data and found to be significant only in the 1s{sup 2}-1s2p({sup 1}P).

  14. Dual scattering foil design for poly-energetic electron beams.

    PubMed

    Kainz, K K; Antolak, J A; Almond, P R; Bloch, C D; Hogstrom, K R

    2005-03-01

    The laser wakefield acceleration (LWFA) mechanism can accelerate electrons to energies within the 6-20 MeV range desired for therapy application. However, the energy spectrum of LWFA-generated electrons is broad, on the order of tens of MeV. Using existing laser technology, the therapeutic beam might require a significant energy spread to achieve clinically acceptable dose rates. The purpose of this work was to test the assumption that a scattering foil system designed for a mono-energetic beam would be suitable for a poly-energetic beam with a significant energy spread. Dual scattering foil systems were designed for mono-energetic beams using an existing analytical formalism based on Gaussian multiple-Coulomb scattering theory. The design criterion was to create a flat beam that would be suitable for fields up to 25 x 25 cm2 at 100 cm from the primary scattering foil. Radial planar fluence profiles for poly-energetic beams with energy spreads ranging from 0.5 MeV to 6.5 MeV were calculated using two methods: (a) analytically by summing beam profiles for a range of mono-energetic beams through the scattering foil system, and (b) by Monte Carlo using the EGS/BEAM code. The analytic calculations facilitated fine adjustments to the foil design, and the Monte Carlo calculations enabled us to verify the results of the analytic calculation and to determine the phase-space characteristics of the broadened beam. Results showed that the flatness of the scattered beam is fairly insensitive to the width of the input energy spectrum. Also, results showed that dose calculated by the analytical and Monte Carlo methods agreed very well in the central portion of the beam. Outside the useable field area, the differences between the analytical and Monte Carlo results were small but significant, possibly due to the small angle approximation. However, these did not affect the conclusion that a scattering foil system designed for a mono-energetic beam will be suitable for a poly

  15. International Nuclear Target Development Society workshop 1983: proceedings

    SciTech Connect

    Thomas, G.

    1983-01-01

    Separate abstracts were prepared for 11 of the 19 papers presented. Eight papers were previously included in the data base. Discussion group session papers on carbon stripper foils, problems in producing heavy-ion targets, and problems in producing general type targets are included. (WHK)

  16. Thermal effects on the clearance and stiffness of foil journal bearings for a Brayton cycle turboalternator

    NASA Technical Reports Server (NTRS)

    Eshel, A.

    1972-01-01

    An analysis of foil journal bearings for a NASA Brayton Cycle Unit (BRU) is presented. The study represents an extension of previous work in that it includes the effects of thermal expansion of foil-bearing components, as well as an improved model of the influence of foil flexure. The results presented give the bearing film thickness, the bearing stiffness, and the foil tension as functions of the operating temperatures and the elasto-hydrodynamic and geometrical parameters pertinent to the design of BRU foil bearings. A computer program for the evaluation of design data and for parametric studies is included.

  17. Physical vapor deposited aluminum foils from high energy density physics experiments

    SciTech Connect

    Barthell, B.L.; Anderson, W.E.; Gomez, V.M.; Henneke, B.F.; Moore, J.E.; Reeves, G.A.; Salazar, M.A.; Townsend, J.D.

    1995-09-01

    Fabrication of cylindrical aluminum load foils and graded thickness aluminum vacuum opening switch foils is described. Load foils are vaporized by joule heating and imploded by J {times} B forces to stagnate on axis and create soft x-rays. Plasma flow switch foils are mounted to shunt the vacuum power flow channel of a coaxial gun and are vaporized by joule heating. The resultant graded density plasma is magnetically driven down the annular power flow channel. Opening switch action occurs when the shunt plasma crosses a load slot in the center conductor. These foil components have been used in both the Pegasus and Procyon experiments.

  18. Quasi-static analysis of foil journal bearings for a Brayton cycle turboalternator

    NASA Technical Reports Server (NTRS)

    Eshel, A.

    1974-01-01

    A quasi-static analysis is presented for foil journal bearings designed for a NASA Brayton Cycle Turboalternator. Included in the analysis are effects of 'slack' (due to flexural rigidity of the foil), of frictionally restrained extension of the foil-length in contact with cylindrical guides, of fluid inertia and compressibility, and of thermal expansion of rotor, foil and supporting structure. Comparisons are made with results of early experiments performed by Licht (1968, 1969) and recent data of Licht and Branger (1973). Variatons of film thickness, foil tension and bearing stiffness are presented graphically as functions of pertinent parameters for the case of operation in zero-gravity environment.

  19. Simultaneous laser cutting and welding of metal foil to edge of a plate

    DOEpatents

    Pernicka, John C.; Benson, David K.; Tracy, C. Edwin

    1996-01-01

    A method of welding an ultra-thin foil to the edge of a thicker sheet to form a vacuum insulation panel comprising the steps of providing an ultra-thin foil having a thickness less than 0.002, providing a top plate having an edge and a bottom plate having an edge, clamping the foil to the edge of the plate wherein the clamps act as heat sinks to distribute heat through the foil, providing a laser, moving the laser relative to the foil and the plate edges to form overlapping weld beads to weld the foil to the plate edges while simultaneously cutting the foil along the weld line formed by the overlapping beads.

  20. Simultaneous laser cutting and welding of metal foil to edge of a plate

    DOEpatents

    Pernicka, J.C.; Benson, D.K.; Tracy, C.E.

    1996-03-19

    A method is described for welding an ultra-thin foil to the edge of a thicker sheet to form a vacuum insulation panel comprising the steps of providing an ultra-thin foil having a thickness less than 0.002, providing a top plate having an edge and a bottom plate having an edge, clamping the foil to the edge of the plate wherein the clamps act as heat sinks to distribute heat through the foil, providing a laser, moving the laser relative to the foil and the plate edges to form overlapping weld beads to weld the foil to the plate edges while simultaneously cutting the foil along the weld line formed by the overlapping beads. 7 figs.

  1. Non-uniformity effects of the inter-foil distance on GEM detector performance

    NASA Astrophysics Data System (ADS)

    Yan, Huang; Han, YI; Zhi-Gang, Xiao; Zhao, Zhang; Wen-Jing, Cheng; Li-Ming, Lü; Wei-Hua, Yan; Ren-Sheng, Wang; Hong-Jie, Li; Yan, Zhang; Li-Min, Duan; Rong-Jiang, Hu; Chen-Gui, Lu; He-Run, Yang; Peng, Ma; Hai-Yan, Gao

    2016-04-01

    The non-uniformity effect of the inter-foil distance has been studied using a gaseous electron multiplication (GEM) detector with sensitive area of 50mm × 50mm. A gradient of the inter-foil distance is introduced by using spacers with different heights at the two ends of the foil gap. While the cluster size and the intrinsic spatial resolution show insignificant dependence on the inter-foil distance, the gain exhibits an approximately linear dependence on the inter-foil distance. From the slope, a quantitative relationship between the change of the inter-foil distance and the change of the gain is derived, which can be used as a method to evaluate the non-uniformity of the foil gap in the application of large-area GEM detectors. Supported by National Natural Science Foundation of China (11375094, U1332207, 11120101004), and by Tsinghua University Initiative Scientific Research Program

  2. Temperature Measurements at Material Interfaces with Thin-Foil Gauges

    NASA Astrophysics Data System (ADS)

    Morley, Mike J.; Chapman, David J.; Proud, William G.

    2009-12-01

    Measurements of shock heating are important in determining Equations of State that incorporate entropic effects. The use of thin-foil nickel gauges to measure shock heating in material was proposed by Rosenberg et al. in the 1980s. This research investigates the use of such commercial thin-foil gauges at interfaces between materials of different thermal and shock properties. The technique requires analysis of the resistance changes of the gauge which is a function of both temperature and stress. The response of manganin gauges to shock loading is well understood, and was used to calibrate for the piezoresistive effect in nickel. Results are presented for a variety of well-characterised materials and the applicability of the proposed method discussed.

  3. Temperature measurements at material interfaces with thin-foil gauges

    NASA Astrophysics Data System (ADS)

    Morley, Mike; Chapman, David; Proud, William

    2009-06-01

    Measurements of shock heating are important in determining Equations of State that incorporate entropic effects. The use of thin-foil nickel gauges to measure shock heating in material was proposed by Rosenberg et al. in the 1980s. This research investigates the use of such commercial thin-foil gauges at interfaces between materials of different thermal and shock properties. The technique requires analysis of the resistance changes of the gauge which is a function of both temperature and stress. The response of manganin gauges to shock loading is well understood, and was used to calibrate for the piezoresistive effect in nickel. Results are presented for a variety of well-characterised materials and the applicability of the proposed method discussed.

  4. Underlying principle of efficient propulsion in flexible plunging foils

    NASA Astrophysics Data System (ADS)

    Zhu, Xiao-Jue; He, Guo-Wei; Zhang, Xing

    2014-12-01

    Passive flexibility was found to enhance propulsive efficiency in swimming animals. In this study, we numerically investigate the roles of structural resonance and hydrodynamic wake resonance in optimizing efficiency of a flexible plunging foil. The results indicates that (1) optimal efficiency is not necessarily achieved when the driving frequency matches the structural eigenfrequency; (2) optimal efficiency always occurs when the driving frequency matches the wake resonant frequency of the time averaged velocity profile. Thus, the underlying principle of efficient propulsion in flexible plunging foil is the hydrodynamic wake resonance, rather than the structural resonance. In addition, we also found that whether the efficiency can be optimized at the structural resonant point depends on the strength of the leading edge vortex relative to that of the trailing edge vortex. The result of this work provides new insights into the role of passive flexibility in flapping-based propulsion.

  5. Electrostatic adhesion of polymer particles to a foil electrode

    NASA Astrophysics Data System (ADS)

    Ziteng, Li; Praeger, Matthew; Smallwood, Jeremy; Lewin, Paul

    2015-10-01

    The SPABRINK EU project requires temporary adhesion of coloured solid “ink” particles to a surface, for later recovery and reuse. This is achieved through the use of dielectrophoretic force under the control of a voltage applied to an interdigitated electrode pattern on the polymer foil. One concern is the ability to hold particles under vibration conditions. In this paper we present an experimental study of the adhesion of 50-300 μm polymer particles to an experimental interdigitated electrode structure on flexible polymer foil. Powder loss as a function of calibrated displacement and applied voltage to the electrodes are presented. This is compared with theoretical results obtained by modelling adhesion using Pohl's equation in terms of an “adhesion factor”. Some difficulties in directly comparing experimental and modelling results are discussed.

  6. Gas Foil Bearing Technology Advancements for Closed Brayton Cycle Turbines

    NASA Technical Reports Server (NTRS)

    Howard, Samuel A.; Bruckner, Robert J.; DellaCorte, Christopher; Radil, Kevin C.

    2007-01-01

    Closed Brayton Cycle (CBC) turbine systems are under consideration for future space electric power generation. CBC turbines convert thermal energy from a nuclear reactor, or other heat source, to electrical power using a closed-loop cycle. The operating fluid in the closed-loop is commonly a high pressure inert gas mixture that cannot tolerate contamination. One source of potential contamination in a system such as this is the lubricant used in the turbomachine bearings. Gas Foil Bearings (GFB) represent a bearing technology that eliminates the possibility of contamination by using the working fluid as the lubricant. Thus, foil bearings are well suited to application in space power CBC turbine systems. NASA Glenn Research Center is actively researching GFB technology for use in these CBC power turbines. A power loss model has been developed, and the effects of a very high ambient pressure, start-up torque, and misalignment, have been observed and are reported here.

  7. CHARACTERIZATION OF MONOLITHIC FUEL FOIL PROPERTIES AND BOND STRENGTH

    SciTech Connect

    D E Burkes; D D Keiser; D M Wachs; J S Larson; M D Chapple

    2007-03-01

    Understanding fuel foil mechanical properties, and fuel / cladding bond quality and strength in monolithic plates is an important area of investigation and quantification. Specifically, what constitutes an acceptable monolithic fuel – cladding bond, how are the properties of the bond measured and determined, and what is the impact of fabrication process or change in parameters on the level of bonding? Currently, non-bond areas are quantified employing ultrasonic determinations that are challenging to interpret and understand in terms of irradiation impact. Thus, determining mechanical properties of the fuel foil and what constitutes fuel / cladding non-bonds is essential to successful qualification of monolithic fuel plates. Capabilities and tests related to determination of these properties have been implemented at the INL and are discussed, along with preliminary results.

  8. Direct drive foil implosion experiments on Pegasus II

    SciTech Connect

    Cochrane, J.C.; Bartsch, R.R.; Benage, J.F.; Forman, P.R.; Gribble, R.F.; Hockaday, M.Y.P.; Hockaday, R.G.; Ladish, J.S.; Oona, H.; Parker, J.V.; Shlachter, J.S.; Wysocki, F.J.

    1993-05-01

    Pegasus II is the upgraded version of Pegasus, a pulsed power machine used in the Los Alamos Above Ground Experiments (AGEX) program. The goal of the program is to produce an intense (>100 TW) source of soft x-rays from the thermalization of the KE of a 1 to 10 MJ collapsing plasma source. The radiation pulse should have a maximum duration of several tens of nanoseconds and will be used in the study of fusion conditions and material properties. This paper addresses z-pinch experiments done on a capacitor bank where the radiating plasma source is formed by an imploding annular aluminum foil driven by the J {times} B forces generated by the current flowing through the foil.

  9. Plasma flow switch and foil implosion experiments on Pegasus II

    SciTech Connect

    Cochrane, J.C.; Bartsch, R.R.; Benage, J.R.; Forman, P.R.; Gribble, R.F.; Ladish, J.S.; Oona, H.; Parker, J.V.; Scudder, D.W.; Shlachter, J.S.; Wysocki, F.J.

    1993-01-01

    Pegasus II is the upgraded version of Pegasus, a pulsed power machine used in the Los Alamos AGEX (Above Ground EXperiments) program. A goal of the program is to produce an intense (> 100 TW) source of soft x-rays from the thermalization of the kinetic energy of a 1 to 10 MJ plasma implosion. The radiation pulse should have a maximum duration of several 10's of nanoseconds and will be used in the study of fusion conditions and material properties. The radiating plasma source will be generated by the thermalization of the kinetic energy of an imploding cylindrical, thin, metallic foil. This paper addresses experiments done on a capacitor bank to develop a switch (plasma flow switch) to switch the bank current into the load at peak current. This allows efficient coupling of bank energy into foil kinetic energy.

  10. Plasma flow switch and foil implosion experiments on Pegasus II

    SciTech Connect

    Cochrane, J.C.; Bartsch, R.R.; Benage, J.R.; Forman, P.R.; Gribble, R.F.; Ladish, J.S.; Oona, H.; Parker, J.V.; Scudder, D.W.; Shlachter, J.S.; Wysocki, F.J.

    1993-07-01

    Pegasus II is the upgraded version of Pegasus, a pulsed power machine used in the Los Alamos AGEX (Above Ground EXperiments) program. A goal of the program is to produce an intense (> 100 TW) source of soft x-rays from the thermalization of the kinetic energy of a 1 to 10 MJ plasma implosion. The radiation pulse should have a maximum duration of several 10`s of nanoseconds and will be used in the study of fusion conditions and material properties. The radiating plasma source will be generated by the thermalization of the kinetic energy of an imploding cylindrical, thin, metallic foil. This paper addresses experiments done on a capacitor bank to develop a switch (plasma flow switch) to switch the bank current into the load at peak current. This allows efficient coupling of bank energy into foil kinetic energy.

  11. Fabrication of microcoined metal foil Rayleigh-Taylor targets

    NASA Astrophysics Data System (ADS)

    Randall, Greg; Vecchio, James; Fitzsimmons, Paul; Knipping, Jack; Wall, Don; Vu, Matthew; Giraldez, Emilio; Remington, Tane; Blue, Brent; Farrell, Michael; Nikroo, Abbas

    2013-03-01

    Rippled metal foils are currently sought for high strain rate material strength studies. For example, the growth of these ripples by the Rayleigh-Taylor instability after a laser-induced ramped compression yields strength behavior at extremely high strain rate. Because metals of interest (iron, tantalum, steel, etc.) typically cannot be diamond turned, we employ a microcoining process to imprint the ~ 5 μm deep by ~ 50 μm long ripples into the metal surface. The process consists of nitriding a steel die, diamond turning the die, and then pressing the die into a polished metal foil of choice (Seugling et al., Proc EUSPEN Int. Conference, 2010). This work details recent process developments, characterization techniques, and important physics for fabrication of these rippled metal targets.

  12. Energy loss of 132Xe-ions in thin foils

    NASA Astrophysics Data System (ADS)

    Trzaska, W. H.; Knyazheva, G. N.; Perkowski, J.; Andrzejewski, J.; Khlebnikov, S. V.; Kozulin, E. M.; Lyapin, V. G.; Malkiewicz, T.; Mutterer, M.

    2009-10-01

    The energy loss of 132Xe-ions in C, Al, Ni, Ag, Lu, Au, Pb and Th foils was measured in the energy range from 0.1 to 5 MeV/u using the TOF-E method. The results are compared with previously published data and with the predictions of several computer codes. They include theoretical codes: PASS, CASP, semi-empirical programs: SRIM, LET and the Hubert table predictions.

  13. Nickel foil microcantilevers for magnetic manipulation and localized heating

    PubMed Central

    Gaitas, Angelo; McNaughton, Brandon H.

    2014-01-01

    Cellular manipulation has been investigated by a number of techniques. In this manuscript nickel foil microcantilevers were used for magnetophoresis and manipulation of microparticles and magnetically labeled HeLa cells. The cantilevers were also used for localized heating in liquid, reaching biologically relevant temperatures. This work aims to develop cantilevers for sample enrichment, manipulation, and thermal applications, offering an inexpensive and versatile solution compatible with standard tools in research and clinical diagnostic testing, such as microwell plates. PMID:25541581

  14. The investigation of electrolytic surface roughening for PCB copper foil

    NASA Astrophysics Data System (ADS)

    Lee, Shuo-Jen; Liu, Chao-Kai

    2013-10-01

    This study is the application of the principle of electrochemical. The anodic dissolution has no concentration polarization. Hence, electrolyte life is substantially increased. The waste copper is high in ion concentration with a recovery value. As compared with the current PCB chemical pre-treatment method, it may have advantages of cost-saving, improvement of overall efficiency, reduction of production costs and reduction of the amount of waste generated. In the development of the copper foil for electrochemical roughening process, the use of electrolysis reaction affects the copper surface dissolution to form a unique bump coarsening. It will increase in the surface area of the copper foil to improve dry film solder mask and the adhesion between the copper surfaces. Four electrolytes, two neutral salts and two acids, were selected to explore the best of the electrolytic roughening parameters of temperature, time and voltage. The surface roughness and the surface morphology of the copper foil were measured before and after the electrolytic surface roughening. Finally, after repeated experiments, electrolytes A and B copper generates obvious inter-granular corrosion, resulting in a rough surface similar to the chemical pre-treatment. On the other hands, the surface morphology resulted from electrolytes C and D appears more like pitting. Both electrolytic could generate surface roughness of Ra 0.3 um roughened copper surface higher than industrial standard.

  15. Thin-foil reflection gratings for Constellation-X

    NASA Astrophysics Data System (ADS)

    Heilmann, Ralf K.; Akilian, Mireille; Chang, Chih-Hao; Forest, Craig R.; Joo, Chulmin; Lapsa, Andrew; Montoya, Juan C.; Schattenburg, Mark L.

    2004-10-01

    The Reflection Grating Spectrometer (RGS) on Constellation-X is designed to supply astronomers with high spectral resolution in the soft x-ray band from 0.25 to 2 keV. High resolution, large collecting area and low mass at grazing incidence require very flat and thin grating substrates, or thin-foil optics. Thin foils typically have a diameter-to-thickness ratio of 200 or higher and as a result very low stiffness. This poses a number of technological challenges in the areas of shaping, handling, positioning, and mounting of such optics. The most minute forces (gravity sag, friction, thermal mismatch with optic mount, etc.) can lead to intolerable deformations and limit figure metrology repeatability. We present results of our efforts in the manipulation and metrology of suitable grating substrates, utilizing a novel low-stress foil holder with friction-reducing flexures. A large number of reflection gratings is needed to achieve the required collecting area. We have employed nanoimprint lithography (NIL) - which uses imprint films as thin as 100 nm or less - for the high-fidelity and low-stress replication from 100 mm diameter saw-tooth grating masters.

  16. Structure and mechanical properties of foils made of nanocrystalline beryllium

    NASA Astrophysics Data System (ADS)

    Zhigalina, O. M.; Semenov, A. A.; Zabrodin, A. V.; Khmelenin, D. N.; Brylev, D. A.; Lizunov, A. V.; Nebera, A. L.; Morozov, I. A.; Anikin, A. S.; Orekhov, A. S.; Kuskova, A. N.; Mishin, V. V.; Seryogin, A. V.

    2016-07-01

    The phase composition and structural features of (45-90)-μm-thick foils obtained from nanocrystalline beryllium during multistep thermomechanical treatment have been established using electron microscopy, electron diffraction, electron backscattering diffraction, and energy-dispersive analysis. This treatment is shown to lead to the formation of a structure with micrometer- and submicrometer-sized grains. The minimum average size of beryllium grains is 352 nm. The inclusions of beryllium oxide (BeO) of different modifications with tetragonal (sp. gr. P42/ mnm) and hexagonal (sp. gr. P63/ mmc) lattices are partly ground during deformation to a size smaller than 100 nm and are located along beryllium grain boundaries in their volume, significantly hindering migration during treatment. The revealed structural features of foils with submicrometer-sized crystallites provide the thermal stability of their structural state. Beryllium with this structure is a promising material for X-ray instrument engineering and for the production of ultrathin (less than 10 μm) vacuum-dense foils with very high physicomechanical characteristics.

  17. Fission foil detector calibrations with high energy protons

    NASA Technical Reports Server (NTRS)

    Benton, E. V.; Frank, A. L.

    1995-01-01

    Fission foil detectors (FFD's) are passive devices composed of heavy metal foils in contact with muscovite mica films. The heavy metal nuclei have significant cross sections for fission when irradiated with neutrons and protons. Each isotope is characterized by threshold energies for the fission reactions and particular energy-dependent cross sections. In the FFD's, fission fragments produced by the reactions are emitted from the foils and create latent particle tracks in the adjacent mica films. When the films are processed surface tracks are formed which can be optically counted. The track densities are indications of the fluences and spectra of neutrons and/or protons. In the past, detection efficiencies have been calculated using the low energy neutron calibrated dosimeters and published fission cross sections for neutrons and protons. The problem is that the addition of a large kinetic energy to the (n,nucleus) or (p,nucleus) reaction could increase the energies and ranges of emitted fission fragments and increase the detector sensitivity as compared with lower energy neutron calibrations. High energy calibrations are the only method of resolving the uncertainties in detector efficiencies. At high energies, either proton or neutron calibrations are sufficient since the cross section data show that the proton and neutron fission cross sections are approximately equal. High energy proton beams have been utilized (1.8 and 4.9 GeV, 80 and 140 MeV) for measuring the tracks of fission fragments emitted backward and forward.

  18. Material Parameters for Creep Rupture of Austenitic Stainless Steel Foils

    NASA Astrophysics Data System (ADS)

    Osman, H.; Borhana, A.; Tamin, M. N.

    2014-08-01

    Creep rupture properties of austenitic stainless steel foil, 347SS, used in compact recuperators have been evaluated at 700 °C in the stress range of 54-221 MPa to establish the baseline behavior for its extended use. Creep curves of the foil show that the primary creep stage is brief and creep life is dominated by tertiary creep deformation with rupture lives in the range of 10-2000 h. Results are compared with properties of bulk specimens tested at 98 and 162 MPa. Thin foil 347SS specimens were found to have higher creep rates and higher rupture ductility than their bulk specimen counterparts. Power law relationship was obtained between the minimum creep rate and the applied stress with stress exponent value, n = 5.7. The value of the stress exponent is indicative of the rate-controlling deformation mechanism associated with dislocation creep. Nucleation of voids mainly occurred at second-phase particles (chromium-rich M23C6 carbides) that are present in the metal matrix by decohesion of the particle-matrix interface. The improvement in strength is attributed to the precipitation of fine niobium carbides in the matrix that act as obstacles to the movement of dislocations.

  19. Low-energy multiple-Coulomb scattering in thick foils

    SciTech Connect

    Morrill, S.M.

    1984-01-01

    Angular and energy distributions were taken using proton and ..cap alpha..-particle beams of energies 2 to 10 MeV incident on a variety of thick foils. Foils were chosen from commonly used materials and to span the periodic table. Foil thicknesses were chosen which resulted in approximately 20-60% energy losses. The lower-energy experiments were done using the Brigham Young University 4-MeV Van de Graaff accelerator while the higher-energy experiments were performed using the Triangle Universities Nuclear Laboratory (TUNL) tandem Van de Graaff. Angular distributions are characterized by the angles at which the distribution had dropped to the 1/e, 1/10, and 1/100 points of their initial values. Energy distributions are characterized by the mean energy and the width of the energy-straggling distribution of the emerging particle. Comparisons are made to the appropriate theories including the angular distribution theory of Nigam, Sundaresan, and Wu (NSW), and the straggling theory of Bethe. Improvements to the NSW method by using an effective energy and effective nuclear charge are discussed.

  20. Low-Energy Multiple-Coulomb Scattering in Thick Foils.

    NASA Astrophysics Data System (ADS)

    Morrill, Steven M.

    Angular and energy distributions were taken using proton and alpha-particle beams of energies 2--10 MeV incident on a variety of thick foils. Foils were chosen from commonly used materials and to span the periodic table. Foil thicknesses were chosen which resulted in approximately 20--60% energy losses. The lower-energy experiments were done using the Brigham Young University 4-MeV Van de Graaff accelerator while the higher-energy experiments were performed using the Triangle Universities Nuclear Laboratory (TUNL) tandem Van de Graaff. Angular distributions were characterized by the angles at which the distribution had dropped to the 1/e, 1/10, and 1/100 points of their initial values. Energy distributions were characterized by the mean energy and the width of the energy straggling distribution of the emerging particle. Comparisons were made to the appropriate theories including the angular distribution theory of Nigam, Sundaresan, and Wu (NSW), and the straggling theory of Bethe. Improvements to the NSW method by using an effective energy and effective nuclear charge were discussed.

  1. Production of large screen-mounted aluminium neutralizer foils

    NASA Astrophysics Data System (ADS)

    Stoner, John O.

    1989-10-01

    In order to convert large-diameter beams of H - to neutral H atoms, aluminum foils having a diameter of 90 cm or more and an areal density of typically 8-12 μg/cm 2 have been proposed. Production of such foils, uniform in thickness to ±20% or better and mounted on thin wire grids, has been accomplished by careful control of substrate preparation, parting-agent application, spatial location of coating filaments, floating speed and temperature, and pickup procedure. Lexan (TM) polycarbonate substrates have been used, because of their uniformity of surface quality. Evaporated NaCl has been used as the parting agent, and an alloy containing 1% silicon rather than pure aluminum has been used as the foil material for greater strength and reliability. To obtain coated areas sufficiently large and uniform, substrates having dimensions of 1.2 m × 1.2 m have been used. A specially configured water tank having a volume of 3.2 m 3 has been built to accept such large substrates. Floating has been done in chilled water to improve its stability, minimize variations in surface tension, and to prevent the development of air bubbles on immersed surfaces. Fractional coverage of better than 95% on meshes having unsupported diameters of greater than 90 cm can now be obtained on a routine basis.

  2. Flow energy harvesting -- another application of the biomimetic flapping foils

    NASA Astrophysics Data System (ADS)

    Zhu, Qiang; Peng, Zhangli

    2009-11-01

    Imitating fish fins and insect wings, flapping foils are usually used for biomimetic propulsion. Theoretical studies and experiments have demonstrated that through specific combinations of heaving and pitching motions, these foils can also extract energy from incoming wind or current. Compared with conventional flow energy harvesting devices based upon rotating turbines, this novel design promises mitigated impact upon the environment. To achieve the required motions, existing studies focus on hydrodynamic mode coupling, in which a periodic pitching motion is activated and a heaving motion is then generated by the oscillating lifting force. Energy extraction is achieved through a damper in the heaving direction (representing the generator). This design involves a complicated control and activation system. In addition, there is always the possibility that the energy required to activate the system exceeds the energy recovered by the generator. We have discovered that a much simpler device without activation, a 2DOF foil mounted on a rotational spring and a damper undergoing flow-induced motions can achieve stable flow energy harvesting. Using Navier-Stokes simulations we predicted different behaviors of the system during flow-induced vibrations and identified the specific requirements to achieve controllable periodic motions essential for stable energy harvesting. The energy harvesting capacity and efficiency were also determined.

  3. Comparison of EXAFS Foil Spectra from Around the World

    SciTech Connect

    Kelly, S. D.; Bare, S. R.; Greenlay, N.; Azevedo, G.; Balasubramanian, M.; Barton, D.; Chattopadhyay, S.; Fakra, S.; Johannessen, B.; Newville, M.; Pena, J.; Pokrovski, G. S; Proux, O.; Priolkar, K.; Ravel, B.; Webb, S. M.

    2010-07-16

    The EXAFS spectra of Cu and Pd foil from many different beamlines and synchrotrons are compared to address the dependence of the amplitude reduction factor (S{sub 0}{sup 2}) on beamline specific parameters. Even though S{sub 0}{sup 2} is the same parameter as the EXAFS coordination number, the value for S{sub 0}{sup 2} is given little attention, and is often unreported. The S{sub 0}{sup 2} often differs for the same material due to beamline and sample attributes, such that no importance is given to S{sub 0}{sup 2}-values within a general range of 0.7 to 1.1. EXAFS beamlines have evolved such that it should now be feasible to use standard S{sub 0}{sup 2} values for all EXAFS measurements of a specific elemental environment. This would allow for the determination of the imaginary energy (Ei) to account for broadening of the EXAFS signal rather than folding these errors into an effective S{sub 0}{sup 2}-value. To test this concept, we model 11 Cu-foil and 6 Pd-foil EXAFS spectra from around the world to compare the difference in S{sub 0}{sup 2}- and Ei-values.

  4. Grain structure of thin electrodeposited and rolled copper foils

    SciTech Connect

    Merchant, H.D. . E-mail: HarishMerchant@aol.com; Liu, W.C.; Giannuzzi, L.A.; Morris, J.G.

    2004-12-15

    Planar and cross-section light optical and transmission electron microscopy (TEM) and X-ray diffraction analysis have been used to characterize the technologically relevant thin copper films and foils. The grain structure and grain orientation of (i) 1-15 {mu}m deposit on the polyimide (PI) substrate (ii) 5-35 {mu}m free-standing foil and (iii) 200 {mu}m sheet prepared by the industrial scale rolling or electrodeposit process have been examined. It is shown that the rolled foil structure is highly anisotropic due to grain stretching during rolling; the pancaked grains circumscribe a dislocation cell substructure. Thermal exposure in the 423-453 K range results in full anneal softening, while initiating the polygonization of cellular substructure, the formation of new large grains by discontinuous recrystallization and the transformation of the near <111> deformation textures into the near <100> anneal textures. The texture transformation is facilitated when the oxygen content of copper is reduced from the normal 100-400 ppm level or when a low level silver ({approx}200 ppm) addition is made to copper. Depending upon the electrodeposition conditions or the nature of additives introduced in the electrolyte, it is possible to develop an electrodeposit with (a) a truly equiaxed, fine, twin-free, randomly oriented grain structure or (b) a relatively coarse grain structure, accompanied by extensive twinning, z (growth)-direction grain extension, columnar grain morphology and strong <220> crystallographic texture. Between (a) and (b), it is possible to tailor the processing to obtain a mix of fine and coarse grains, a large fraction of random orientation component (weak near <220> textures), moderate twinning, and vestiges of columnar grain morphology and z-direction grain extension. The anneal softening is not accompanied by significant grain structure modification or by texture change; somewhat above the softening temperature, an in situ grain growth ensues. For both

  5. Measurement of H{sup {minus}}, H{sup 0}, and H{sup +} yields produced by foil stripping of 800-MeV H{sup {minus}} ions

    SciTech Connect

    Gulley, M.S.; Keating, P.B.; Bryant, H.C.; MacKerrow, E.P.; Miller, W.A.; Rislove, D.C.; Cohen, S.; Donahue, J.B.; Fitzgerald, D.H.; Frankle, S.C.; Funk, D.J.; Hutson, R.L.; Macek, R.J.; Plum, M.A.; Stanciu, N.G.; van Dyck, O.B.; Wilkinson, C.A.; Planner, C.W.

    1996-05-01

    Measurements of H{sup {minus}} stripping and H{sup 0} excited-state production for a wide range of foil thicknesses and experimental conditions are reported. An 800-MeV H{sup {minus}} beam was passed through carbon or aluminum oxide foils of thicknesses ranging from 10 to 550 {mu}g/cm{sup 2} and the excited states produced were analyzed by field stripping in a special magnet downstream of the foil. The foil thicknesses were independently determined. The H{sup 0} atoms emerging in excited states with {ital n}{approx_gt}2 can be stripped to protons in fields of up to 1.3 T. The yield of excited states as a function of foil thickness and the cross sections for the various interactions are presented. The cross-section ratio of double to single ionization of H{sup {minus}} in carbon is found to be (1.8{plus_minus}0.9){percent}. {copyright} {ital 1996 The American Physical Society.}

  6. Microstructure and Mechanical Properties of AA1235 Aluminum Foil Stocks Produced Directly from Electrolytic Aluminum Melt

    NASA Astrophysics Data System (ADS)

    Xiong, Hanqing; Yu, Kun; Wen, Li; Yao, Sujuan; Dai, Yilong; Wang, Zhifeng

    2016-02-01

    A new process is developed to obtain high-quality AA1235 aluminum foil stocks and to replace the traditional manufacture process. During the new manufacture process, AA1235 aluminum sheets are twin-roll casted directly through electrolytic aluminum melt (EAM), and subsequently the sheets are processed into aluminum foil stocks by cold rolling and annealing. Microstructure and mechanical properties of the AA1235 aluminum sheets produced through such new process are investigated in each state by optimal microscope, scanning electron microscopy, X-ray diffraction, orientation imaging microscopy, transmission electron microscopy, etc. The results show that compared with the traditional AA1235 aluminum foil stocks produced through re-melted aluminum melt (RAM), the amount of impurities is decreased in the EAM aluminum foil stocks. The EAM aluminum foil stock obtains less β-FeSiAl5 phases, but more α-Fe2SiAl8 phases. The elongation of EAM aluminum foil stocks is improved significantly owing to more cubic orientation. Especially, the elongation value of the EAM aluminum foil stocks is approximately 25 pct higher than that of the RAM aluminum foil stocks. As a result, the EAM aluminum foil stocks are at an advantage in increasing the processing performance for the aluminum foils during subsequent processes.

  7. Pu-Zr alloy for high-temperature foil-type fuel

    DOEpatents

    McCuaig, Franklin D.

    1977-01-01

    A nuclear reactor fuel alloy consists essentially of from slightly greater than 7 to about 4 w/o zirconium, balance plutonium, and is characterized in that the alloy is castable and is rollable to thin foils. A preferred embodiment of about 7 w/o zirconium, balance plutonium, has a melting point substantially above the melting point of plutonium, is rollable to foils as thin as 0.0005 inch thick, and is compatible with cladding material when repeatedly cycled to temperatures above 650.degree. C. Neutron reflux densities across a reactor core can be determined with a high-temperature activation-measurement foil which consists of a fuel alloy foil core sandwiched and sealed between two cladding material jackets, the fuel alloy foil core being a 7 w/o zirconium, plutonium foil which is from 0.005 to 0.0005 inch thick.

  8. Pu-ZR Alloy high-temperature activation-measurement foil

    DOEpatents

    McCuaig, Franklin D.

    1977-08-02

    A nuclear reactor fuel alloy consists essentially of from slightly greater than 7 to about 4 w/o zirconium, balance plutonium, and is characterized in that the alloy is castable and is rollable to thin foils. A preferred embodiment of about 7 w/o zirconium, balance plutonium, has a melting point substantially above the melting point of plutonium, is rollable to foils as thin as 0.0005 inch thick, and is compatible with cladding material when repeatedly cycled to temperatures above 650.degree. C. Neutron flux densities across a reactor core can be determined with a high-temperature activation-measurement foil which consists of a fuel alloy foil core sandwiched and sealed between two cladding material jackets, the fuel alloy foil core being a 7 w/o zirconium, plutonium foil which is from 0.005 to 0.0005 inch thick.

  9. Measurement of the radon diffusion through a nylon foil for different air humidities

    SciTech Connect

    Mamedov, Fadahat; Štekl, Ivan; Smolek, Karel

    2015-08-17

    The dependency of the radon penetration through a nylon foil on air humidity was measured. Such information is needed for the tracking part of the SuperNEMO detector, which is planned to be shielded against radon by nylon foil and in which the air humidity is not negligible. The long term measurements of radon penetration through nylon foils for different air humidities were performed with the radon diffusion setup constructed at the IEAP, CTU in Prague. The setup consists of two stainless steel hemispheres with Si detector in each of them. Both hemispheres are separated by the tested foil. While the left hemisphere contains high Rn activity, the right part contains only activity caused by the radon penetration through the tested foil. Obtained results of this study with a nylon foil with the thickness of 50 µm are presented.

  10. Measurement of the radon diffusion through a nylon foil for different air humidities

    NASA Astrophysics Data System (ADS)

    Mamedov, Fadahat; Štekl, Ivan; Smolek, Karel

    2015-08-01

    The dependency of the radon penetration through a nylon foil on air humidity was measured. Such information is needed for the tracking part of the SuperNEMO detector, which is planned to be shielded against radon by nylon foil and in which the air humidity is not negligible. The long term measurements of radon penetration through nylon foils for different air humidities were performed with the radon diffusion setup constructed at the IEAP, CTU in Prague. The setup consists of two stainless steel hemispheres with Si detector in each of them. Both hemispheres are separated by the tested foil. While the left hemisphere contains high Rn activity, the right part contains only activity caused by the radon penetration through the tested foil. Obtained results of this study with a nylon foil with the thickness of 50 µm are presented.

  11. Analysis of cartilage-polydioxanone foil composite grafts.

    PubMed

    Kim, James H; Wong, Brian

    2013-12-01

    This study presents an analytical investigation into the mechanical behavior of a cartilage-polydioxanone (PDS) plate composite grafts. Numerical methods are used to provide a first-order, numerical model of the flexural stiffness of a cartilage-PDS graft. Flexural stiffness is a measure of resistance to bending and is inversely related to the amount of deformation a structure may experience when subjected to bending forces. The cartilage-PDS graft was modeled as a single composite beam. Using Bernoulli-Euler beam theory, a closed form equation for the theoretical flexural stiffness of the composite graft was developed. A parametric analysis was performed to see how the flexural properties of the composite model changed with varying thicknesses of PDS foil. The stiffness of the cartilage-PDS composite using 0.15-mm-thick PDS was four times higher than cartilage alone. The composite with a 0.5-mm-thick PDS graft was only 1.7 times stiffer than the composite with the 0.15-mm-thick PDS graft. Although a thicker graft material will yield higher flexural stiffness for the composite, the relationship between composite stiffness and PDS thickness is nonlinear. After a critical point, increments in graft thickness produce gradually smaller improvements in flexural stiffness. The small increase in stiffness when using the thicker PDS foils versus the 0.15 mm PDS foil may not be worth the potential complications (prolonged foreign body reaction, reduction in nutrient diffusion to cartilage) of using thicker artificial grafts. PMID:24327249

  12. Experimental research of the fine foil explosion dynamics

    NASA Astrophysics Data System (ADS)

    Zhigalin, A. S.; Rousskikh, A. G.; Oreshkin, V. I.; Chaikovsky, S. A.; Ratakhin, N. A.; Kuznetsov, V. V.

    2014-11-01

    The work is devoted to studying of substances properties at high specific deposit energy using double-frame pulsed backlighting system. The high specific deposit energy was reached at electrical conductor explosion (ECE). Fast mode of ECE was investigated. Fine foils of aluminum, cooper, titanium and nickel were used as conductors. Experiments were carried out on the experimental complex consisting of three current generators. The first generator WEG-' was used for explosion of the fine conductors. This generator represents fast capacitor with capacity 250 nF, which was charged to voltage 10 to 30 kV. The investigated conductor was mounted in special holder and the foil contacts with the electrodes were soldered. Two other generators - radiographs XPG-1 and G2 with x-pinch load were used two frame X-ray backlighting imaging. The generators current pulses had amplitude 300 kA and rising time 180 ns with a low inductance load. Four crossed molybdenum wires with diameter of 25 μm were used to form an x-pinch. Using of the x-pinches soft x-ray radiation the images of exploded foil were registered with temporal resolution of 2 ns. The images were detected by a photo film located behind the filter. The x-ray imaging, together with the measurements of the current flowing through a conductor and voltage on the exploded conductor had allowed inferring of the energy deposited into the conductor, delay time of the bubbles formation relative to the moment of current- cutoff and the time dependence of the vapor bubbles quantity.

  13. Short-pulse high intensity laser thin foil interaction

    NASA Astrophysics Data System (ADS)

    Audebert, Patrick

    2003-10-01

    The technology of ultrashort pulse laser generation has progressed to the point that optical pulses larger than 10 J, 300 fs duration or shorter are routinely produced. Such pulses can be focused to intensities exceeding 10^18 W/cm^2. With high contrast pulses, these focused intensities can be used to heat solid matter to high temperatures with minimal hydrodynamic expansion, producing an extremely high energy-density state of matter for a short period of time. This high density, high temperature plasma can be studied by x-ray spectroscopy. We have performed experiments on thin foils of different elements under well controlled conditions at the 100 Terawatt laser at LULI to study the characteristics X-ray emission of laser heated solids. To suppress the ASE effect, the laser was frequency doubled. S-polarized light with a peak intensity of 10^19W/cm^2 was used to minimize resonance absorption. To decrease the effect of longitudinal temperature gradients very thin (800 μ) aluminum foil targets were used. We have also studied the effect of radial gradient by limiting the measured x-ray emission zone using 50μ or 100μ pinhole on target. The spectra, in the range 7-8Å, were recorded using a conical crystal spectrometer coupled to a 800 fs resolution streak camera. A Fourier Domain Interferometry (FDI) of the back of the foil was also performed providing a measurement of the hydrodynamic expansion as function of time for each shot. To simulate the experiment, we used the 1D hydrodynamic code FILM with a given set of plasma parameter (ρ, Te) as initial conditions. The X-ray emission was calculated by post processing hydrodynamic results with a collisional-radiative model which uses super-configuration average atomic data. The simulation reproduces the main features of the experimental time resolved spectrum.

  14. Laser Proton acceleration from mass limited silicon foils

    NASA Astrophysics Data System (ADS)

    Zeil, K.; Kraft, S.; Richter, T.; Metzkes, J.; Bussmann, M.; Schramm, U.; Sauerbrey, R.; Cowan, T. E.; Fuchs, J.; Buffechoux, S.

    2009-11-01

    We present recent studies on laser proton acceleration experiments using mass limited silicon targets. Small micro machined silicon foils with 2 μm thickness and 20x20 μm2 to 100x100μm2 size mounted on very tiny stalks were shot with the 100 TW LULI Laser (long pulse 150 fs) and with the new 150 TW DRACO Laser facility (short pulse 30 fs) of the Research Centre Dresden-Rossendorf. The experiments were carried out using high contrast levels. Proton spectra have been measured with magnetic spectrometers and radio chromic film stacks.

  15. Promising HE for explosive welding of thin metallic foils

    NASA Astrophysics Data System (ADS)

    Deribas, A. A.; Mikhaylov, A. L.; Titova, N. N.; Zocher, Marvin A.

    2012-03-01

    Experimental results are presented on the development of a high explosive (HE) suitable for the welding of thin metallic foils. The explosive is formed from a mixture of brisant HE (RDX or PETN) and an inert material, namely sodium bicarbonate. Sodium bicarbonate releases a rather large quantity of gas during decomposition, the effects of which are discussed. Measurements of detonation velocity and critical thickness for specific mixture combinations are presented. It is shown that particle size (of the RDX or PETN component) has a significant effect upon detonation velocity and critical thickness. Compositions were developed which have a stable detonation velocity ~2 km/s with a layer thickness ~ 2 mm.

  16. Prediction of Gas Lubricated Foil Journal Bearing Performance

    NASA Technical Reports Server (NTRS)

    Carpino, Marc; Talmage, Gita

    2003-01-01

    This report summarizes the progress in the first eight months of the project. The objectives of this research project are to theoretically predict the steady operating conditions and the rotor dynamic coefficients of gas foil journal bearings. The project is currently on or ahead of schedule with the development of a finite element code that predicts steady bearing performance characteristics such as film thickness, pressure, load, and drag. Graphical results for a typical bearing are presented in the report. Project plans for the next year are discussed.

  17. Standardizable method for testing foil-substrate adherence

    NASA Astrophysics Data System (ADS)

    Schell, Karel J.; Klinker, Han; van Renesse, Rudolf L.

    2002-04-01

    An increasing number of currencies is provided with an Optically Variable Device (OVD) as a counterfeit deterrent. The device is adhered to the substrate by a hot melt adhesive. Adherence is generally tested with an adhesive tape, a practical test that sufficed up to now. Nevertheless, the question may be raised if a method can be developed with a better discriminating power as well as a larger potential for standardization. A feasibility test with the IGT printability tester, using a high viscosity pick up oil, shows promising results. This paper presents the testing method, shows a few preliminary results and discusses these results with respect to the foil application method.

  18. Optical observations of molecular dissociation in thin foils

    SciTech Connect

    Berry, H.G.; Gay, T.J.; Brooks, R.L.

    1981-01-01

    We have measured the intensity and polarizations of light emitted from atomic excited states of dissociated molecular ions. Using HeH/sup +/ projectiles, we have observed factors of 1 to 5 enhancements of the light from n=3, /sup 1/ /sup 3/P,D states of He I and some He II and H I emissions. Observations of Lyman-..cap alpha.. emission after dissociation of H/sub 2//sup +/ and H/sub 3//sup +/ show rapid variations in light yield for small internuclear separations at the foil surface.

  19. Role of induced vortex interaction in a semi-active flapping foil based energy harvester

    NASA Astrophysics Data System (ADS)

    Wu, J.; Chen, Y. L.; Zhao, N.

    2015-09-01

    The role of induced vortex interaction in a semi-active flapping foil based energy harvester is numerically examined in this work. A NACA0015 airfoil, which acts as an energy harvester, is placed in a two-dimensional laminar flow. It performs an imposed pitching motion that subsequently leads to a plunging motion. Two auxiliary smaller foils, which rotate about their centers, are arranged above and below the flapping foil, respectively. As a consequence, the vortex interaction between the flapping foil and the rotating foil is induced. At a Reynolds number of 1100 and the position of the pitching axis at one-third chord, the effects of the distance between two auxiliary foils, the phase difference between the rotating motion and the pitching motion as well as the frequency of pitching motion on the power extraction performance are systematically investigated. It is found that compared to the single flapping foil, the efficiency improvement of overall power extraction for the flapping foil with two auxiliary foils can be achieved. Based on the numerical analysis, it is indicated that the enhanced power extraction, which is caused by the increased lift force, thanks to the induced vortex interaction, directly benefits the efficiency enhancement.

  20. Design and validation of novel scattering foils for modulated electron radiation therapy.

    PubMed

    Connell, T; Seuntjens, J

    2014-05-21

    Modulated Electron Radiation Therapy (MERT) continues to be an area of interest to various groups, however, the scattering foils used in beam flattening have not been optimized for this modality. In this work, the feasibility of novel scattering foils specifically designed for MERT is investigated using Monte Carlo methods. Different designs based on foil material, shape and thickness were analyzed. It was shown that low atomic number materials such as aluminum were optimal, while shaped foils such as those employed in current dual foil designs were not necessary. Aluminum foil thickness between 0.36 mm and 1.50 mm were capable of sufficiently broadening beams with energies between 12 MeV and 20 MeV respectively, with beams of lower energies receiving sufficient scatter from the treatment head components and air scatter. Finally, custom foils were manufactured based upon previously simulated designs and were placed into the beamline of a 2100 EX accelerator, and showed excellent agreement between the simulated and measured PDDs and profiles. Custom foils achieved higher dose rates on the central axis compared to the clinical foils by factors of 5.4, 4.9 and 4.5 for 12 MeV, 16 MeV and 20 MeV, respectively. PMID:24743426

  1. Hydrodynamics of foils swimming in a side-by-side configuration

    NASA Astrophysics Data System (ADS)

    Dewey, Peter; Moored, Keith; Quinn, Daniel; Smits, Alexander

    2013-11-01

    Experimental and computational results are presented on a pair of hydrofoils undergoing pitch oscillations in a side-by-side configuration. The time-averaged forces and propulsive efficiency are independently measured for each foil for a range of separation distances and oscillation phase differentials between the two foils. The results are compared to an isolated foil to determine if the presence of a second foil can yield an improvement to the propulsive characteristics of the system. While the exact performance of the side-by-side foils is strongly dependent on the separation distance and phase differential between the foils, it is found that under certain configurations an enhancement in net thrust is achieved by the presence of a second foil. The wake patterns shed by the foils as they oscillate are also examined and compared to the propulsive characteristics. A series of four stable wake configurations are observed that depend on the phase differential between the foils. Supported by the Office of Naval Research under Program Director Dr. Bob Brizzolara, MURI grant number N00014-08-1-0642.

  2. Goal-directed mechanisms that constrain retrieval predict subsequent memory for new "foil" information.

    PubMed

    Vogelsang, David A; Bonnici, Heidi M; Bergström, Zara M; Ranganath, Charan; Simons, Jon S

    2016-08-01

    To remember a previous event, it is often helpful to use goal-directed control processes to constrain what comes to mind during retrieval. Behavioral studies have demonstrated that incidental learning of new "foil" words in a recognition test is superior if the participant is trying to remember studied items that were semantically encoded compared to items that were non-semantically encoded. Here, we applied subsequent memory analysis to fMRI data to understand the neural mechanisms underlying the "foil effect". Participants encoded information during deep semantic and shallow non-semantic tasks and were tested in a subsequent blocked memory task to examine how orienting retrieval towards different types of information influences the incidental encoding of new words presented as foils during the memory test phase. To assess memory for foils, participants performed a further surprise old/new recognition test involving foil words that were encountered during the previous memory test blocks as well as completely new words. Subsequent memory effects, distinguishing successful versus unsuccessful incidental encoding of foils, were observed in regions that included the left inferior frontal gyrus and posterior parietal cortex. The left inferior frontal gyrus exhibited disproportionately larger subsequent memory effects for semantic than non-semantic foils, and significant overlap in activity during semantic, but not non-semantic, initial encoding and foil encoding. The results suggest that orienting retrieval towards different types of foils involves re-implementing the neurocognitive processes that were involved during initial encoding. PMID:27431039

  3. Design and validation of novel scattering foils for modulated electron radiation therapy

    NASA Astrophysics Data System (ADS)

    Connell, T.; Seuntjens, J.

    2014-05-01

    Modulated Electron Radiation Therapy (MERT) continues to be an area of interest to various groups, however, the scattering foils used in beam flattening have not been optimized for this modality. In this work, the feasibility of novel scattering foils specifically designed for MERT is investigated using Monte Carlo methods. Different designs based on foil material, shape and thickness were analyzed. It was shown that low atomic number materials such as aluminum were optimal, while shaped foils such as those employed in current dual foil designs were not necessary. Aluminum foil thickness between 0.36 mm and 1.50 mm were capable of sufficiently broadening beams with energies between 12 MeV and 20 MeV respectively, with beams of lower energies receiving sufficient scatter from the treatment head components and air scatter. Finally, custom foils were manufactured based upon previously simulated designs and were placed into the beamline of a 2100 EX accelerator, and showed excellent agreement between the simulated and measured PDDs and profiles. Custom foils achieved higher dose rates on the central axis compared to the clinical foils by factors of 5.4, 4.9 and 4.5 for 12 MeV, 16 MeV and 20 MeV, respectively.

  4. Nanostructured Pt-CeO2 thin film catalyst grown on graphite foil by magnetron sputtering

    NASA Astrophysics Data System (ADS)

    Vorokhta, Mykhailo; Khalakhan, Ivan; Matolínová, Iwa; Kobata, Masaaki; Yoshikawa, Hideki; Kobayashi, Keisuke; Matolín, Vladimir

    2013-02-01

    Layers of different thickness of CeO2 doped by Pt were prepared by magnetron sputtering on different substrates: Si (1 0 0) and a graphite foil. The structure and chemical composition of the Pt-CeO2 catalysts have been investigated by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and hard X-ray photoelectron spectroscopy (HAXPES). SEM showed that the layers prepared on different substrates had very different morphology. XPS and HAXPES studies demonstrated that Pt was dispersed only in Pt2+ and Pt4+ oxidation states in CeO2. Intensity of Pt2+- and Pt4+-peaks was affected by the plasma substrate interaction effects showing that carbon substrate played an active role by determining the film structure. The Pt2+/Pt4+ and Ce3+/Ce4+ ratios depend on the layer thickness and increases in the case of the graphite substrate. The reduced character of porous layer was explained by a general effect of formation of defects and oxygen vacancies at oxide edges and steps, and oxygen reaction with carbon which is responsible of formation of oxygen deficient cerium oxide at the interface.

  5. Personnel neutron dosimetry using electrochemically etched CR-39 foils

    SciTech Connect

    Hankins, D.E.; Homann, S.; Westermark, J.

    1986-09-17

    A personnel neutron dosimetry system has been developed based on the electrochemical etching of CR-39 plastic at elevated temperatures. The doses obtained using this dosimeter system are more accurate than those obtained using other dosimetry systems, especially when varied neutron spectra are encountered. This Cr-39 dosimetry system does not have the severe energy dependence that exists with albedo neutron dosimeters or the fading and reading problems encountered with NTA film. The dosimetry system employs an electrochemical etch procedure that be used to process large numbers of Cr-39 dosimeters. The etch procedure is suitable for operations where the number of personnel requires that many CR-39 dosimeters be processed. Experience shows that one full-time technician can etch and evaluate 2000 foils per month. The energy response to neutrons is fairly flat from about 80 keV to 3.5 MeV, but drops by about a factor of three in the 13 to 16 MeV range. The sensitivity of the dosimetry system is about 7 tracks/cm/sup 2//mrem, with a background equivalent to about 8 mrem for new CR-39 foils. The limit of sensitivity is approximately 10 mrem. The dosimeter has a significant variation in directional dependence, dropping to about 20% at 90/sup 0/. This dosimeter has been used for personnel neutron dosimetry at the Lawrence Livermore National Laboratory for more tha 18 months. 6 refs., 23 figs., 2 tabs.

  6. Fission fragment assisted reactor concept for space propulsion: Foil reactor

    NASA Technical Reports Server (NTRS)

    Wright, Steven A.

    1991-01-01

    The concept is to fabricate a reactor using thin films or foils of uranium, uranium oxide and then to coat them on substrates. These coatings would be made so thin as to allow the escaping fission fragments to directly heat a hydrogen propellant. The idea was studied of direct gas heating and direct gas pumping in a nuclear pumped laser program. Fission fragments were used to pump lasers. In this concept two substrates are placed opposite each other. The internal faces are coated with thin foil of uranium oxide. A few of the advantages of this technology are listed. In general, however, it is felt that if one look at all solid core nuclear thermal rockets or nuclear thermal propulsion methods, one is going to find that they all pretty much look the same. It is felt that this reactor has higher potential reliability. It has low structural operating temperatures, very short burn times, with graceful failure modes, and it has reduced potential for energetic accidents. Going to a design like this would take the NTP community part way to some of the very advanced engine designs, such as the gas core reactor, but with reduced risk because of the much lower temperatures.

  7. A simple method for the measurement of reflective foil emissivity

    NASA Astrophysics Data System (ADS)

    Ballico, M. J.; van der Ham, E. W. M.

    2013-09-01

    Reflective metal foil is widely used to reduce radiative heat transfer within the roof space of buildings. Such foils are typically mass-produced by vapor-deposition of a thin metallic coating onto a variety of substrates, ranging from plastic-coated reinforced paper to "bubble-wrap". Although the emissivity of such surfaces is almost negligible in the thermal infrared, typically less than 0.03, an insufficiently thick metal coating, or organic contamination of the surface, can significantly increase this value. To ensure that the quality of the installed insulation is satisfactory, Australian building code AS/NZS 4201.5:1994 requires a practical agreed method for measurement of the emissivity, and the standard ASTM-E408 is implied. Unfortunately this standard is not a "primary method" and requires the use of specified expensive apparatus and calibrated reference materials. At NMIA we have developed a simple primary technique, based on an apparatus to thermally modulate the sample and record the apparent modulation in infra-red radiance with commercially available radiation thermometers. The method achieves an absolute accuracy in the emissivity of approximately 0.004 (k=2). This paper theoretically analyses the equivalence between the thermal emissivity measured in this manner, the effective thermal emissivity in application, and the apparent emissivity measured in accordance with ASTM-E408.

  8. A simple method for the measurement of reflective foil emissivity

    SciTech Connect

    Ballico, M. J.; Ham, E. W. M. van der

    2013-09-11

    Reflective metal foil is widely used to reduce radiative heat transfer within the roof space of buildings. Such foils are typically mass-produced by vapor-deposition of a thin metallic coating onto a variety of substrates, ranging from plastic-coated reinforced paper to 'bubble-wrap'. Although the emissivity of such surfaces is almost negligible in the thermal infrared, typically less than 0.03, an insufficiently thick metal coating, or organic contamination of the surface, can significantly increase this value. To ensure that the quality of the installed insulation is satisfactory, Australian building code AS/NZS 4201.5:1994 requires a practical agreed method for measurement of the emissivity, and the standard ASTM-E408 is implied. Unfortunately this standard is not a 'primary method' and requires the use of specified expensive apparatus and calibrated reference materials. At NMIA we have developed a simple primary technique, based on an apparatus to thermally modulate the sample and record the apparent modulation in infra-red radiance with commercially available radiation thermometers. The method achieves an absolute accuracy in the emissivity of approximately 0.004 (k=2). This paper theoretically analyses the equivalence between the thermal emissivity measured in this manner, the effective thermal emissivity in application, and the apparent emissivity measured in accordance with ASTM-E408.

  9. Hydrodynamics of a biologically inspired tandem flapping foil configuration

    NASA Astrophysics Data System (ADS)

    Akhtar, Imran; Mittal, Rajat; Lauder, George V.; Drucker, Elliot

    2007-05-01

    Numerical simulations have been used to analyze the effect that vortices, shed from one flapping foil, have on the thrust of another flapping foil placed directly downstream. The simulations attempt to model the dorsal-tail fin interaction observed in a swimming bluegill sunfish. The simulations have been carried out using a Cartesian grid method that allows us to simulate flows with complex moving boundaries on stationary Cartesian grids. The simulations indicate that vortex shedding from the upstream (dorsal) fin is indeed capable of increasing the thrust of the downstream (tail) fin significantly. Vortex structures shed by the upstream dorsal fin increase the effective angle-of-attack of the flow seen by the tail fin and initiate the formation of a strong leading edge stall vortex on the downstream fin. This stall vortex convects down the surface of the tail and the low pressure associated with this vortex increases the thrust on the downstream tail fin. However, this thrust augmentation is found to be quite sensitive to the phase relationship between the two flapping fins. The numerical simulations allows us to examine in detail, the underlying physical mechanism for this thrust augmentation.

  10. Pitching-motion-activated flapping foil near solid walls for power extraction: A numerical investigation

    NASA Astrophysics Data System (ADS)

    Wu, J.; Qiu, Y. L.; Shu, C.; Zhao, N.

    2014-08-01

    A numerical investigation on the power extraction of a pitching-motion-activated flapping foil near solid walls is performed by using an immersed boundary-lattice Boltzmann method in this study. The flapping motions of the foil include a forced pitching component and an induced plunging component. The foil is placed either near a solid wall or between two parallel plane walls. Compared to previous work on the flapping foil for power extraction, the effect of the walls is first considered in this work. At a Reynolds number of 1100 and with the position of the foil pitching axis at third chord, the influences of the mechanical parameters (such as damping coefficient and spring constant) of the foil, the amplitude and frequency of the pitching motion and the clearance between the foil pitching axis and the wall on the power extraction performance of the flapping foil are systematically evaluated. Compared to the situation of free stream, the power extraction performance of the foil near the wall is improved. For given amplitude and frequency, as the clearance decreases the net power extraction efficiency improves. Moreover, as the foil is placed near one wall, there is a transverse shift to the plunging motion that consequently weakens the improvement of net power extraction efficiency. In contrast, the shift can be significantly eliminated as the foil is placed between two walls, which can further improve the net power extraction efficiency. In addition, it is found that the efficiency improvement is essentially from the increased power extraction, which is due to the generation of high lift force.

  11. Spectral content of buried Ag foils at 10{sup 16} W/cm{sup 2} laser illumination

    SciTech Connect

    Huntington, C. M. Maddox, B. R.; Park, H.-S.; Prisbrey, S.; Remington, B. A.

    2014-11-15

    Sources of 5–12 keV thermal Heα x-rays are readily generated by laser irradiation of mid-Z foils at intensities >10{sup 14} W/cm{sup 2}, and are widely used as probes for inertial confinement fusion and high-energy-density experiments. Higher energy 17–50 keV x-ray sources are efficiently produced from “cold” Kα emission using short pulse, petawatt lasers at intensities >10{sup 18} W/cm{sup 2} [H.-S. Park, B. R. Maddox et al., “High-resolution 17–75 keV backlighters for high energy density experiments,” Phys. Plasmas 15(7), 072705 (2008); B. R. Maddox, H. S. Park, B. A. Remington et al., “Absolute measurements of x-ray backlighter sources at energies above 10 keV,” Phys. Plasmas 18(5), 056709 (2011)]. However, when long pulse (>1 ns) lasers are used with Z > 30 elements, the spectrum contains contributions from both K shell transitions and from ionized atomic states. Here we show that by sandwiching a silver foil between layers of high-density carbon, the ratio of Kα:Heα in the x-ray spectrum is significant increased over directly illuminated Ag foils, with narrower lines from K-shell transitions. Additionally, the emission volume is more localized for the sandwiched target, producing a more planar x-ray sheet. This technique may be useful for generating probes requiring spectral purity and a limited spatial extent, for example, in incoherent x-ray Thomson scattering experiments.

  12. Porous carbon-coated graphite electrodes for energy production from salinity gradient using reverse electrodialysis

    NASA Astrophysics Data System (ADS)

    Lee, Su-Yoon; Jeong, Ye-Jin; Chae, So-Ryong; Yeon, Kyeong-Ho; Lee, Yunkyu; Kim, Chan-Soo; Jeong, Nam-Jo; Park, Jin-Soo

    2016-04-01

    Performance of graphite foil electrodes coated by porous carbon black (i.e., Vulcan) was investigated in comparison with metal electrodes for reverse electrodialysis (RED) application. The electrode slurry that was used for fabrication of the porous carbon-coated graphite foil is composed of 7.2 wt% of carbon black (Vulcan X-72), 0.8 wt% of a polymer binder (polyvinylidene fluoride, PVdF), and 92.0 wt% of a mixing solvent (dimethylacetamide, DMAc). Cyclic voltammograms of both the porous carbon (i.e., Vulcan)-coated graphite foil electrode and the graphite foil electrode without Vulcan showed good reversibility in the hexacyanoferrate(III) (i.e., Fe(CN)63-) and hexacyanoferrate(II) (i.e., Fe(CN)64-) redox couple and 1 M Na2SO4 at room temperature. However, anodic and cathodic current of the Vulcan-coated graphite foil electrode was much higher than those of the graphite foil electrode. Using a bench-scale RED stack, the current-voltage polarization curve of the Vulcan-coated graphite electrode was compared to that of metal electrodes such as iridium (Ir) and platinum (Pt). From the results, it was confirmed that resistance of four different electrodes increased with the following order: the Vulcan-coated graphite foilfoil. Moreover, the Vulcan-coated graphite foil showed 5-10% higher power density than the metal mesh electrodes. From the polarization curve of the Vulcan-coated graphite foil electrode, it was found that total resistance decreased as thickness and geometric surface area of the electrode increased.

  13. Prism Foil from an LCD Monitor as a Tool for Teaching Introductory Optics

    ERIC Educational Resources Information Center

    Planinsic, Gorazd; Gojkosek, Mihael

    2011-01-01

    Transparent prism foil is part of a backlight system in LCD monitors that are widely used today. This paper describes the optical properties of the prism foil and several pedagogical applications suitable for undergraduate introductory physics level. Examples include experiments that employ refraction, total internal reflection, diffraction and…

  14. Ultrasmooth metallic foils for growth of high quality graphene by chemical vapor deposition

    NASA Astrophysics Data System (ADS)

    Procházka, Pavel; Mach, Jindřich; Bischoff, Dominik; Lišková, Zuzana; Dvořák, Petr; Vaňatka, Marek; Simonet, Pauline; Varlet, Anastasia; Hemzal, Dušan; Petrenec, Martin; Kalina, Lukáš; Bartošík, Miroslav; Ensslin, Klaus; Varga, Peter; Čechal, Jan; Šikola, Tomáš

    2014-05-01

    Synthesis of graphene by chemical vapor deposition is a promising route for manufacturing large-scale high-quality graphene for electronic applications. The quality of the employed substrates plays a crucial role, since the surface roughness and defects alter the graphene growth and cause difficulties in the subsequent graphene transfer. Here, we report on ultrasmooth high-purity copper foils prepared by sputter deposition of Cu thin film on a SiO2/Si template, and the subsequent peeling off of the metallic layer from the template. The surface displays a low level of oxidation and contamination, and the roughness of the foil surface is generally defined by the template, and was below 0.6 nm even on a large scale. The roughness and grain size increase occurred during both the annealing of the foils, and catalytic growth of graphene from methane (≈1000 °C), but on the large scale still remained far below the roughness typical for commercial foils. The micro-Raman spectroscopy and transport measurements proved the high quality of graphene grown on such foils, and the room temperature mobility of the graphene grown on the template stripped foil was three times higher compared to that of one grown on the commercial copper foil. The presented high-quality copper foils are expected to provide large-area substrates for the production of graphene suitable for electronic applications.

  15. Ultrasmooth metallic foils for growth of high quality graphene by chemical vapor deposition.

    PubMed

    Procházka, Pavel; Mach, Jindřich; Bischoff, Dominik; Lišková, Zuzana; Dvořák, Petr; Vaňatka, Marek; Simonet, Pauline; Varlet, Anastasia; Hemzal, Dušan; Petrenec, Martin; Kalina, Lukáš; Bartošík, Miroslav; Ensslin, Klaus; Varga, Peter; Čechal, Jan; Šikola, Tomáš

    2014-05-01

    Synthesis of graphene by chemical vapor deposition is a promising route for manufacturing large-scale high-quality graphene for electronic applications. The quality of the employed substrates plays a crucial role, since the surface roughness and defects alter the graphene growth and cause difficulties in the subsequent graphene transfer. Here, we report on ultrasmooth high-purity copper foils prepared by sputter deposition of Cu thin film on a SiO2/Si template, and the subsequent peeling off of the metallic layer from the template. The surface displays a low level of oxidation and contamination, and the roughness of the foil surface is generally defined by the template, and was below 0.6 nm even on a large scale. The roughness and grain size increase occurred during both the annealing of the foils, and catalytic growth of graphene from methane (≈1000 °C), but on the large scale still remained far below the roughness typical for commercial foils. The micro-Raman spectroscopy and transport measurements proved the high quality of graphene grown on such foils, and the room temperature mobility of the graphene grown on the template stripped foil was three times higher compared to that of one grown on the commercial copper foil. The presented high-quality copper foils are expected to provide large-area substrates for the production of graphene suitable for electronic applications. PMID:24739598

  16. Effects of the foil flatness on irradiation performance of U10Mo monolithic mini-plates

    SciTech Connect

    Ozaltun, Hakan; Medvedev, Pavel G.; Rabin, Barry H.

    2015-09-03

    Monolithic plate-type fuels comprise of a high density, low enrichment, U10Mo fuel foil encapsulated in a cladding material. This concept generates several fabrication challenges such as flatness, centering or thickness variation. There are concerns, if these parameters have implications on overall performance. To investigate these inquiries, the effects of the foil flatness were studied. For this, a representative plate was simulated for an ideal case. The simulations were repeated for additional cases with various foil curvatures to evaluate the effects on the irradiation performance. The results revealed that the stresses and strains induced by fabrication process are not affected by the flatness of the foil. Furthermore, fabrication stresses in the foil are relieved relatively fast in the reactor. The effects of the foil flatness on peak irradiation stressstrains are minimal. There is a slight increase in temperature for the case with maximum curvature. The major impact is on the displacement characteristics. Furthermore, while the case with a flat foil produces a symmetrical swelling, if the foil is curved, more swelling occurs on the thin-cladding side and the plate bows during irradiation.

  17. Effects of the foil flatness on irradiation performance of U10Mo monolithic mini-plates

    DOE PAGESBeta

    Ozaltun, Hakan; Medvedev, Pavel G.; Rabin, Barry H.

    2015-09-03

    Monolithic plate-type fuels comprise of a high density, low enrichment, U10Mo fuel foil encapsulated in a cladding material. This concept generates several fabrication challenges such as flatness, centering or thickness variation. There are concerns, if these parameters have implications on overall performance. To investigate these inquiries, the effects of the foil flatness were studied. For this, a representative plate was simulated for an ideal case. The simulations were repeated for additional cases with various foil curvatures to evaluate the effects on the irradiation performance. The results revealed that the stresses and strains induced by fabrication process are not affected bymore » the flatness of the foil. Furthermore, fabrication stresses in the foil are relieved relatively fast in the reactor. The effects of the foil flatness on peak irradiation stressstrains are minimal. There is a slight increase in temperature for the case with maximum curvature. The major impact is on the displacement characteristics. Furthermore, while the case with a flat foil produces a symmetrical swelling, if the foil is curved, more swelling occurs on the thin-cladding side and the plate bows during irradiation.« less

  18. 75 FR 1596 - Grant of Authority for Subzone Status, Reynolds Packaging LLC (Aluminum Foil Liner Stock...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-01-12

    ... Register (74 FR 14956, 4-2-2009) and the application has been processed pursuant to the FTZ Act and the... (Aluminum Foil Liner Stock), Louisville, Kentucky Pursuant to its authority under the Foreign-Trade Zones... to the Board for authority to establish a special-purpose subzone at the aluminum foil liner...

  19. Foil Cooling for the Rep-Rated Electron Beam Pumped Electra Laser

    NASA Astrophysics Data System (ADS)

    Giuliani, J. L.; Hegeler, F.; Wolford, M. F.; Abdel-Khalik, S.

    2005-10-01

    The Electra program at the Naval Research Laboratory is developing the science and technologies for implementation of krypton-fluoride (KrF) lasers in inertial fusion energy. Large aperture KrF lasers are pumped by electron beams which transit a foil separating the gas target at >=1 atm pressure from the vacuum diode. A fraction of the beam energy is deposited in the foil and thus long term (>=10^8 shots), rep-rated (5 Hz) operation requires active cooling of the foil to prevent thermal yield relaxation and cycling fatigue. This paper will report on experimental data and theoretical analysis of two diverse approaches to foil thermal management: convective and conductive cooling. Convective turbulent cooling has been operational on the Electra main amp through the use of oscillating louvers within a gas recirculator containing the pumped lasing region. At 5 Hz the foil temperature (Tf) can be maintained at ˜400 ^oC for a 1 mil SS foil. Conduction cooling provides the simplest configuration with only the need for water channels in the ribs of the hibachi. For a 1 mil Al foil, Tf is predicted to be ˜140 ^oC at 5 Hz. Comparison of experimental and theoretical results and advanced foil materials will be discussed.

  20. Feasibility development program LEU-foil plate type target for the production of Mo-99

    SciTech Connect

    Allen, C.W.; Butler, R.A.; Jarousse, C.; Falgoux, J.L.

    2008-07-15

    The University of Missouri Research Reactor and AREVA-CERCA have recently signed a Memorandum of Understanding to cooperate in a program to determine the feasibility of manufacturing a prototype LEU-foil target in a plate geometry for the production of molybdenum-99. The concept of a plate type target consists of transitioning Argonne National Laboratory's existing LEU-foil annular target design from a concentric tube geometry to a plate geometry. The objectives of the feasibility determination are: 1) Evaluate the structural integrity and geometric stability of a foil plate target during irradiation and post-irradiation by finite element analysis modeling. 2) Evaluate the heat transfer characteristics of a foil plate target with respect to thermal contact resistance at the foil / plate interfaces. 3) Determine the economics of manufacturing an LEU-foil plate target in comparison to that of a LEU dispersion plate type target on a commercial scale basis. 4) Determine the most effective and efficient method of disassembling the target to remove the foil component of the target for chemical processing. The results of the structural and thermal analyses will be used to determine if a comprehensive set of Safety Case documentation can be developed to support the irradiation and disassembly of a 'mini' (i.e., small scale) LEU-foil plate target as a trial demonstration. (author)

  1. Foil assisted replica molding for fabrication of microfluidic devices and their application in vitro.

    PubMed

    Micheal, Issac J; Vidyasagar, Aditya J; Bokara, Kiran Kumar; Mekala, Naveen Kumar; Asthana, Amit; Rao, Ch Mohan

    2014-10-01

    We present a simple, rapid, benchtop, Foil Assisted Rapid Molding (FARM) method for the fabrication of microfluidic devices. This novel technique involves the use of aluminium foil, pen and an X-Y plotter to create semi-circular or plano-concave, shallow microchannels. It is an easy do-it-yourself (DIY) technique for creating a microfluidic device in three simple steps: (1) create a channel design using the CAD software, (2) plot the patterns on aluminium foil and (3) use the reverse of the engraved foil as a mold to create microfluidic devices. In this report, we present a detailed study of the proposed method by varying a range of parameters such as foil thickness, tip material, and tip sizes and by investigating their effect on the creation of channels with varying geometry. Furthermore, we demonstrated the cytocompatibility of these devices in vitro. PMID:25102283

  2. Lead foil in dental X-ray film: Backscattering rejection or image intensifier?

    NASA Astrophysics Data System (ADS)

    Hönnicke, M. G.; Delben, G. J.; Godoi, W. C.; Swinka-Filho, V.

    2014-11-01

    Dental X-ray films are still largely used due to sterilization issues, simplicity and, mainly, economic reasons. These films almost always are double coated (double emulsion) and have a lead foil in contact with the film for X-ray backscattering rejection. Herein we explore the use of the lead foil as an image intensifier. In these studies, spatial resolution was investigated when images were acquired on the dental X-ray films with and without the lead foil. Also, the lead foil was subjected to atomic analysis (fluorescent measurements) and structure analysis (X-ray diffraction). We determined that the use of the lead foil reduces the exposure time, however, does not affect the spatial resolution on the acquired images. This suggests that the fluorescent radiation spread is smaller than the grain sizes of the dental X-ray films.

  3. Design, fabrication, and performance of foil journal bearing for the brayton rotating unit

    NASA Technical Reports Server (NTRS)

    Licht, L.; Branger, M.

    1973-01-01

    Foil bearings were designed and manufactured to replace pivoted-shoe journal bearings in an existing Brayton Cycle turbo-alternator-compressor. The design of this unconventional rotor support was accomplished within the constraints and space limitations imposed by the present machine, and the substitution of foil bearings was effected without changes or modification other machine components. A housing and a test rig were constructed to incorporate the new foil-bearing support into a unified assemble with an air-driven rotor and the gimbal-mounted thrust bearing, seals, and shrouds of an actual Brayton Rotating Unit. The foil bearing required no external pressure source, and stable self-acting rotation was achieved at all speeds up to 43,200 rpm. Excellent wipe-wear characteristics of the foil bearing permitted well over 1000 start-stop cycles with no deterioriation of performance in the entire speed range.

  4. Conical foil x-ray mirrors: performance and projections.

    PubMed

    Serlemitsos, P J

    1988-04-15

    For the past decade, we have been developing at Goddard conical grazing incidence mirrors in an effort to increase the sensitivity and resolution of astronomical observations in the iron K spectral band around 7 keV. Tightly packed conical foils give us the option of trading some imaging capability for light weight, large throughput, and low cost, all crucial requirements at the higher energies where grazing angles become very small. Nearing the completion of the broad band x-ray telescope for NASA's SHEAL II mission, we have decided important design and fabrication issues including reflector substrate material and supports and most techniques for reflector preparation, mirror assembly, and alignment. We will review the design, fabrication, status, and performance of our present mirrors. Future applications along with prospects for improved spatial resolution for these mirrors will be discussed. PMID:20531595

  5. Multilayer roll bonded aluminium foil: processing, microstructure and flow stress

    SciTech Connect

    Barlow, C.Y.; Nielsen, P.; Hansen, N

    2004-08-02

    Bulk aluminium has been produced by warm-rolling followed by cold-rolling of commercial purity (99% purity) aluminium foil. The bonding appeared perfect from observation with the naked eye, light and transmission electron microscopy. By comparison with bulk aluminium of similar purity (AA1200) rolled to a similar strain (90%RA), the roll-bonded metal showed a much higher density of high-angle grain boundaries, similar strength and improved thermal stability. This study has implications for a number of applications in relation to the processing of aluminium. Roll bonding is of interest as a method for grain size refinement; oxide-containing materials have increased strength, enhanced work-hardening behaviour, and exhibit alterations in recrystallisation behaviour. The behaviour of the hard oxide film is of interest in aluminium processing, and has been investigated by characterising the size and distribution of oxide particles in the roll-bonded samples.

  6. Visualization of terahertz surface waves propagation on metal foils

    PubMed Central

    Wang, Xinke; Wang, Sen; Sun, Wenfeng; Feng, Shengfei; Han, Peng; Yan, Haitao; Ye, Jiasheng; Zhang, Yan

    2016-01-01

    Exploitation of surface plasmonic devices (SPDs) in the terahertz (THz) band is always beneficial for broadening the application potential of THz technologies. To clarify features of SPDs, a practical characterization means is essential for accurately observing the complex field distribution of a THz surface wave (TSW). Here, a THz digital holographic imaging system is employed to coherently exhibit temporal variations and spectral properties of TSWs activated by a rectangular or semicircular slit structure on metal foils. Advantages of the imaging system are comprehensively elucidated, including the exclusive measurement of TSWs and fall-off of the time consumption. Numerical simulations of experimental procedures further verify the imaging measurement accuracy. It can be anticipated that this imaging system will provide a versatile tool for analyzing the performance and principle of SPDs. PMID:26729652

  7. Flow structures in the wake of heaving and pitching foils

    NASA Astrophysics Data System (ADS)

    Najdzin, Derek; Pardo, Enrique; Leftwich, Megan C.; Bardet, Philippe M.

    2012-11-01

    A 10-bar mechanism drives a cambering hydrofoil in an oscillatory heaving and pitching motion that replicates the flapping motion of a dolphin tail. The mechanism sits on a force-balance with six strain gages that together measure the forces and moments experienced by the fin during an oscillation. Planar Laser-Induced Fluorescence is used to image the flow structures created downstream of the cambering fin for a range of Reynolds and Strouhal numbers. The images are taken in the mid-plane, parallel to the bottom of the water tunnel. These results are compared to a rigid foil at matching conditions to investigate the role of camber changes during the flapping cycle.

  8. Visualization of terahertz surface waves propagation on metal foils.

    PubMed

    Wang, Xinke; Wang, Sen; Sun, Wenfeng; Feng, Shengfei; Han, Peng; Yan, Haitao; Ye, Jiasheng; Zhang, Yan

    2016-01-01

    Exploitation of surface plasmonic devices (SPDs) in the terahertz (THz) band is always beneficial for broadening the application potential of THz technologies. To clarify features of SPDs, a practical characterization means is essential for accurately observing the complex field distribution of a THz surface wave (TSW). Here, a THz digital holographic imaging system is employed to coherently exhibit temporal variations and spectral properties of TSWs activated by a rectangular or semicircular slit structure on metal foils. Advantages of the imaging system are comprehensively elucidated, including the exclusive measurement of TSWs and fall-off of the time consumption. Numerical simulations of experimental procedures further verify the imaging measurement accuracy. It can be anticipated that this imaging system will provide a versatile tool for analyzing the performance and principle of SPDs. PMID:26729652

  9. Foil-like manganin gauges for dynamic high pressure measurements

    NASA Astrophysics Data System (ADS)

    Duan, Zhuoping; Liu, Yan; Pi, Aiguo; Huang, Fenglei

    2011-07-01

    Foil-like manganin gauges with a variety of shapes used in different ranges of pressure for the one-dimensional strain mode and axisymmetric strain mode were designed for measuring the detonation pressures of explosives and high shock pressure in materials. In the stress range of 0-53.5 GPa, the pressure-piezoresistance relationships of the manganin gauges were calibrated by the light gas gun and the planar lens of explosive. The piezoresistance coefficients were obtained in different ranges of pressure. To verify the coefficients, the detonation pressure (CJ pressure) of TNT explosive was measured by the manganin gauges, which give similar CJ pressure values to those reported by Zhang et al (2009 Detonation Physics (Beijing: Ordnance Industry Press)) with the maximum relative deviation being less than 3%.

  10. Deposition of selenium coatings on beryllium foils. Revision 1

    SciTech Connect

    Erikson, E.D.; Tassano, P.L.; Reiss, R.H.; Griggs, G.E.

    1984-01-01

    A technique for preparing selenium films on 50.8 micrometers thick beryllium foils is described. The selenium was deposited in vacuum from a resistance heated evaporation source. A water-cooled enclosure was used to minimize contamination of the vacuum system and to reduce the exposure of personnel to toxic and obnoxious materials. Profilometry measurements of the coatings indicated selenium thicknesses of 5.5, 12.9, 37.5, 49.8 and 74.5 micrometers. The control of deposition rate and of coating thickness was facilitated using a commercially available closed-loop programmable deposition controller. The x-ray transmission of the coated substrates was measured using a tritiated zirconium source. The transmissivities of the film/substrate combination are presented for the range of energies from 4 to 20 keV.

  11. An Innovative Method for Manufacturing Gamma-TiAl Foil

    NASA Technical Reports Server (NTRS)

    Hales, Stephen J.; Saqib, Mohammad; Alexa, Joel A.

    2003-01-01

    The manufacture and entrance into service of thin gage gamma-TiAl product has been hampered by the inherent low room temperature ductility of the material. In the present study a new approach was explored for the efficient manufacture of gamma-TiAl foil with improved ductility. The objective was to produce a very clean material (low interstitial content) with a highly refined, homogeneous microstructure placed in a fully lamellar condition. The processing route involved the use of RF plasma spray deposition of pre-alloyed powders, followed by consolidation via vacuum hot pressing and heat treatment. The approach took advantage of a deposition process which included no electrodes, no binders and high cooling rates. Results and discussion of the work performed to date are presented.

  12. The affect of erbium hydride on the conversion efficience to accelerated protons from ultra-shsort pulse laser irradiated foils

    SciTech Connect

    Offermann, Dustin Theodore

    2008-01-01

    This thesis work explores, experimentally, the potential gains in the conversion efficiency from ultra-intense laser light to proton beams using erbium hydride coatings. For years, it has been known that contaminants at the rear surface of an ultra-intense laser irradiated thin foil will be accelerated to multi-MeV. Inertial Confinement Fusion fast ignition using proton beams as the igniter source requires of about 1016 protons with an average energy of about 3MeV. This is far more than the 1012 protons available in the contaminant layer. Target designs must include some form of a hydrogen rich coating that can be made thick enough to support the beam requirements of fast ignition. Work with computer simulations of thin foils suggest the atomic mass of the non-hydrogen atoms in the surface layer has a strong affect on the conversion efficiency to protons. For example, the 167amu erbium atoms will take less energy away from the proton beam than a coating using carbon with a mass of 12amu. A pure hydrogen coating would be ideal, but technologically is not feasible at this time. In the experiments performed for my thesis, ErH3 coatings on 5 μm gold foils are compared with typical contaminants which are approximately equivalent to CH1.7. It will be shown that there was a factor of 1.25 ± 0.19 improvement in the conversion efficiency for protons above 3MeV using erbium hydride using the Callisto laser. Callisto is a 10J per pulse, 800nm wavelength laser with a pulse duration of 200fs and can be focused to a peak intensity of about 5 x 1019W/cm2. The total number of protons from either target type was on the order of 1010. Furthermore, the same experiment was performed on the Titan laser, which has a 500fs pulse duration, 150J of energy and can be focused to about 3 x 1020 W/cm2. In this experiment 1012 protons were seen from both erbium hydride and

  13. The effect of erbium hydride on the conversion efficiency to accelerated protons from ultra-short pulse laser irradiated foils

    NASA Astrophysics Data System (ADS)

    Offermann, Dustin Theodore

    This thesis work explores, experimentally, the potential gains in the conversion efficiency from ultra-intense laser light to proton beams using erbium hydride coatings. For years, it has been known that contaminants at the rear surface of an ultra-intense laser irradiated thin foil will be accelerated to multi-MeV. Inertial Confinement Fusion fast ignition using proton beams as the igniter source requires of about 10 16 protons with an average energy of about 3MeV. This is far more than the 1012 protons available in the contaminant layer. Target designs must include some form of a hydrogen rich coating that can be made thick enough to support the beam requirements of fast ignition. Work with computer simulations of thin foils suggest the atomic mass of the non-hydrogen atoms in the surface layer has a strong affect on the conversion efficiency to protons. For example, the 167amu erbium atoms will take less energy away from the proton beam than a coating using carbon with a mass of 12amu. A pure hydrogen coating would be ideal, but technologically is not feasible at this time. In the experiments performed for my thesis, ErH 3 coatings on 5mum gold foils are compared with typical contaminants which are approximately equivalent to CH 1.7. It will be shown that there was a factor of 1.25 +/- 0.19 improvement in the conversion efficiency for protons above 3MeV using erbium hydride using the Callisto laser. Callisto is a 10J per pulse, 800nm wavelength laser with a pulse duration of 200fs and can be focused to a peak intensity of about 5 x 1019W/cm2. The total number of protons from either target type was on the order of 1010. Furthermore, the same experiment was performed on the Titan laser, which has a 500fs pulse duration, 150J of energy and can be focused to about 3 x 1020W/cm 2. In this experiment 1012 protons were seen from both erbium hydride and contaminants on 14mum gold foils. Significant improvements were also observed but possibly because of the depletion of

  14. CO2 Capture by Absorption with Potassium Carbonate

    SciTech Connect

    Gary T. Rochelle; Eric Chen; Babatunde Oyenekan; Andrew Sexton; Jason Davis; Marus Hiilliard; Qing Xu; David Van Wagener; Jorge M. Plaza

    2006-12-31

    The objective of this work is to improve the process for CO{sub 2} capture by alkanolamine absorption/stripping by developing an alternative solvent, aqueous K{sub 2}CO{sub 3} promoted by piperazine. The best solvent and process configuration, matrix with MDEA/PZ, offers 22% and 15% energy savings over the baseline and improved baseline, respectively, with stripping and compression to 10 MPa. The energy requirement for stripping and compression to 10 MPa is about 20% of the power output from a 500 MW power plant with 90% CO{sub 2} removal. The stripper rate model shows that a ''short and fat'' stripper requires 7 to 15% less equivalent work than a ''tall and skinny'' one. The stripper model was validated with data obtained from pilot plant experiments at the University of Texas with 5m K{sup +}/2.5m PZ and 6.4m K{sup +}/1.6m PZ under normal pressure and vacuum conditions using Flexipac AQ Style 20 structured packing. Experiments with oxidative degradation at low gas rates confirm the effects of Cu{sup +2} catalysis; in MEA/PZ solutions more formate and acetate is produced in the presence of Cu{sup +2}. At 150 C, the half life of 30% MEA with 0.4 moles CO{sub 2}/mole amine is about 2 weeks. At 100 C, less than 3% degradation occurred in two weeks. The solubility of potassium sulfate in MEA solution increases significantly with CO{sub 2} loading and decreases with MEA concentration. The base case corrosion rate in 5 M MEA/1,2M PZ is 22 mpy. With 1 wt% heat stable salt, the corrosion rate increases by 50% to 160% in the order: thiosulfate< oxalatecarbonate is ineffective in the absence of oxygen, but 50 to 250 ppm reduces corrosion to less than 2 mpy in the presence of oxygen.

  15. Flexible Field Emitter for X-ray Generation by Implanting CNTs into Nickel Foil

    NASA Astrophysics Data System (ADS)

    Sun, Bin; Wang, Yan; Ding, Guifu

    2016-07-01

    This paper reports a novel implanting micromachining technology. By using this method, for the first time, we could implant nano-scale materials into milli-scale metal substrates at room temperature. Ni-based flexible carbon nanotube (CNT) field emitters were fabricated by the novel micromachining method. By embedding CNT roots into Ni foil using polymer matrix as transfer media, effective direct contact between Ni and CNTs was achieved. As a result, our novel emitter shows relatively good field emission properties such as low turn-on field and good stability. Moreover, the emitter was highly flexible with preservation of the field emission properties. The excellent field emission characteristics attributed to the direct contact and the strong interactions between CNTs and the substrate. To check the practical application of the novel emitter, a simple X-ray imaging system was set up by modifying a traditional tube. The gray shadow that appears on the sensitive film after being exposed to the radiation confirms the successful generation of X-ray.

  16. Flexible Field Emitter for X-ray Generation by Implanting CNTs into Nickel Foil.

    PubMed

    Sun, Bin; Wang, Yan; Ding, Guifu

    2016-12-01

    This paper reports a novel implanting micromachining technology. By using this method, for the first time, we could implant nano-scale materials into milli-scale metal substrates at room temperature. Ni-based flexible carbon nanotube (CNT) field emitters were fabricated by the novel micromachining method. By embedding CNT roots into Ni foil using polymer matrix as transfer media, effective direct contact between Ni and CNTs was achieved. As a result, our novel emitter shows relatively good field emission properties such as low turn-on field and good stability. Moreover, the emitter was highly flexible with preservation of the field emission properties. The excellent field emission characteristics attributed to the direct contact and the strong interactions between CNTs and the substrate. To check the practical application of the novel emitter, a simple X-ray imaging system was set up by modifying a traditional tube. The gray shadow that appears on the sensitive film after being exposed to the radiation confirms the successful generation of X-ray. PMID:27401089

  17. Gas Electron Multiplier foil holes: a study of mechanical and deformation effects

    NASA Astrophysics Data System (ADS)

    Benussi, L.; Bianco, S.; Saviano, G.; Muhammad, S.; Piccolo, D.; Suhaj, A.; Sharma, A.; Caponero, M.; Passamonti, L.; Pierluigi, D.; Russo, A.; Lalli, A.; Valente, M.; Ferrini, M.; Langeslag, S. A. E.; Sgobba, S.; Aviles, I.; Magnani, A.; Vai, I.

    2016-08-01

    The GEM detectors will be installed at the Compact Muon Solenoid (CMS) experiment during Long Shutdown II of the LHC in 2018. The GEM foil is a basic part of the detector which consists of a composite material, i.e. polyimide coated with copper and perforated with a high density of micro holes. In this paper the results of the GEM foil material characterization are reported, and a campaign of tensile and holes deformation tests is performed. During the tests, the complex radiation environment at CMS is taken into account and samples are prepared accordingly to see the impacts of the radiation on the GEM foil, i.e. non-irradiated samples are used as the reference and compared with neutrons- and gamma- irradiated. These studies provide the information necessary to optimize the stress level without damaging the foil and holes during the detector assembly in which the GEM foils stack is stretched simultaneously to maintain the uniform gap among the foils in order to get the designed performance of the detector. Finally, an estimate of the Young's modulus of the GEM foil is provided by using the tensile test data.

  18. Evaluation of chromic acid anodized aluminum foil coated composite tubes for the Space Station truss structure

    NASA Technical Reports Server (NTRS)

    Dursch, Harry W.; Slemp, Wayne S.

    1988-01-01

    This paper describes the development and evaluation of chromic acid anodized (CAA) Al foil as a protective and thermal control coating for graphite/epoxy tubes designed for the Space Station truss structure. Special consideration is given to the development of solar-absorptance and thermal-emittance properties required of Al foil, the development of CAA parameters necessary to achieve these optical properties, and the atomic oxygen and UV testing of CAA Al foil. Results showed that 0.003-in CAA Al foil cocured or secondary bonded to graphite/epoxy tubes with thin epoxy film adhesive retains excellent bond strength and provides a superior protective and thermal control coating to the LEO environment. Processes were developed for CAA Al foils long enough to continuously wrap the 23-ft-long diagonal struts of the Space Station truss structure. Specifications are presented for the processes of chromic acid anodizing of Al foil and for the bonding of anodized Al foil to graphite/epoxy tubes.

  19. An Assessment of Gas Foil Bearing Scalability and the Potential Benefits to Civilian Turbofan Engines

    NASA Technical Reports Server (NTRS)

    Bruckner, Robert J.

    2010-01-01

    Over the past several years the term oil-free turbomachinery has been used to describe a rotor support system for high speed turbomachinery that does not require oil for lubrication, damping, or cooling. The foundation technology for oil-free turbomachinery is the compliant foil bearing. This technology can replace the conventional rolling element bearings found in current engines. Two major benefits are realized with this technology. The primary benefit is the elimination of the oil lubrication system, accessory gearbox, tower shaft, and one turbine frame. These components account for 8 to 13 percent of the turbofan engine weight. The second benefit that compliant foil bearings offer to turbofan engines is the capability to operate at higher rotational speeds and shaft diameters. While traditional rolling element bearings have diminished life, reliability, and load capacity with increasing speeds, the foil bearing has a load capacity proportional to speed. The traditional applications for foil bearings have been in small, lightweight machines. However, recent advancements in the design and manufacturing of foil bearings have increased their potential size. An analysis, grounded in experimentally proven operation, is performed to assess the scalability of the modern foil bearing. This analysis was coupled to the requirements of civilian turbofan engines. The application of the foil bearing to larger, high bypass ratio engines nominally at the 120 kN (approx.25000 lb) thrust class has been examined. The application of this advanced technology to this system was found to reduce mission fuel burn by 3.05 percent.

  20. Suppression of instability by double ablation in tungsten doped polyvinyl alcohol foils

    NASA Astrophysics Data System (ADS)

    Peedikakkandy, Leshma; Chaurasia, S.

    2012-07-01

    In Inertial fusion Energy (IFE) research stable acceleration of fusion targets is a significant problem due to hydrodynamic instabilities. This paper presents the results of the experiments done to investigate the effects of doping 20% of Tungsten (W) (by weight) in Polyvinyl Alcohol (PVA) polymer foils for suppression of instability during laser ablative acceleration. A 20J, 1.060μm, 900ps, Nd: Glass laser system with a focusable intensity of 3 to 9.6×1013W/cm2 was used in the experiment. It is observed that the doped PVA targets yielded stable and enhanced foil acceleration as compared to the undoped PVA foils.

  1. Thermally-induced stresses in graphite-epoxy tubes coated with aluminum foil

    NASA Technical Reports Server (NTRS)

    Knott, Tamara W.; Hyer, M. W.

    1989-01-01

    Thermally-induced stresses in the foil, adhesive, and graphite-epoxy layers of composite tubes with aluminum foil bonded to the inner and outer surface are computed. The thermal effects are due to a temperature decrease from the processing temperature of the material to a temperature felt to represent the space environment, the intended operating environment of the tubes. Tubes fabricated from T300/934 and P75s/934 material systems are considered. The results indicate that the presence of the foil and adhesive have no detrimental effect on the stresses in the tube.

  2. Formation and evolution of tweed structures on high-purity aluminum polycrystalline foils under cyclic tension

    SciTech Connect

    Kuznetsov, P. V.; Vlasov, I. V.; Sklyarova, E. A.; Smekalina, T. V.

    2015-10-27

    Peculiarities of formation and evolution of tweed structures on the surface of high-purity aluminum polycrystalline foils under cyclic tension were studied using an atom force microscope and a white light interferometer. Tweed structures of micron and submicron sizes were found on the foils at different number of cycles. In the range of 42,000 < N < 95,000 cycles destruction of tweed patterns is observed, which leads to their disappearance from the surface of the foils. Formation of tweed structures of various scales is discussed in terms of the Grinfeld instability.

  3. FULL SIZE U-10MO MONOLITHIC FUEL FOIL AND FUEL PLATE FABRICATION-TECHNOLOGY DEVELOPMENT

    SciTech Connect

    G. A. Moore; J-F Jue; B. H. Rabin; M. J. Nilles

    2010-03-01

    Full-size U10Mo foils are being developed for use in high density LEU monolithic fuel plates. The application of a zirconium barrier layer too the foil is applied using a hot co-rolling process. Aluminum clad fuel plates are fabricated using Hot Isostatic Pressing (HIP) or a Friction Bonding (FB) process. An overview is provided of ongoing technology development activities, including: the co-rolling process, foil shearing/slitting and polishing, cladding bonding processes, plate forming, plate-assembly swaging, and fuel plate characterization. Characterization techniques being employed include, Ultrasonic Testing (UT), radiography, and microscopy.

  4. Shock compression response of highly reactive Ni + Al multilayered thin foils

    NASA Astrophysics Data System (ADS)

    Kelly, Sean C.; Thadhani, Naresh N.

    2016-03-01

    The shock-compression response of Ni + Al multilayered thin foils is investigated using laser-accelerated thin-foil plate-impact experiments over the pressure range of 2 to 11 GPa. The foils contain alternating Ni and Al layers (parallel but not flat) of nominally 50 nm bilayer spacing. The goal is to determine the equation of state and shock-induced reactivity of these highly reactive fully dense thin-foil materials. The laser-accelerated thin-foil impact set-up involved combined use of photon-doppler-velocimetry to monitor the acceleration and impact velocity of an aluminum flyer, and VISAR interferometry was used to monitor the back free-surface velocity of the impacted Ni + Al multilayered target. The shock-compression response of the Ni + Al target foils was determined using experimentally measured parameters and impedance matching approach, with error bars identified considering systematic and experimental errors. Meso-scale CTH shock simulations were performed using real imported microstructures of the cross-sections of the multilayered Ni + Al foils to compute the Hugoniot response (assuming no reaction) for correlation with their experimentally determined equation of state. It was observed that at particle velocities below ˜150 m/s, the experimentally determined equation of state trend matches the CTH-predicted inert response and is consistent with the observed unreacted state of the recovered Ni + Al target foils from this velocity regime. At higher particle velocities, the experimentally determined equation of state deviates from the CTH-predicted inert response. A complete and self-sustained reaction is also seen in targets recovered from experiments performed at these higher particle velocities. The deviation in the measured equation of state, to higher shock speeds and expanded volumes, combined with the observation of complete reaction in the recovered multilayered foils, confirmed via microstructure characterization, is indicative of the occurrence

  5. Eddy current probe with foil sensor mounted on flexible probe tip and method of use

    DOEpatents

    Viertl, John R. M.; Lee, Martin K.

    2001-01-01

    A pair of copper coils are embedded in the foil strip. A first coil of the pair generates an electromagnetic field that induces eddy currents on the surface, and the second coil carries a current influenced by the eddy currents on the surface. The currents in the second coil are analyzed to obtain information on the surface eddy currents. An eddy current probe has a metal housing having a tip that is covered by a flexible conductive foil strip. The foil strip is mounted on a deformable nose at the probe tip so that the strip and coils will conform to the surface to which they are applied.

  6. CO2 Capture by Absorption with Potassium Carbonate

    SciTech Connect

    Gary T. Rochelle; Andrew Sexton; Jason Davis; Marcus Hilliard; Qing Xu; David Van Wagener; Jorge M. Plaza

    2007-03-31

    The objective of this work is to improve the process for CO{sub 2} capture by alkanolamine absorption/stripping by developing an alternative solvent, aqueous K{sub 2}CO{sub 3} promoted by piperazine. The best K{sup +}/PZ solvent, 4.5 m K{sup +}/4.5 m PZ, requires equivalent work of 31.8 kJ/mole CO{sub 2} when used with a double matrix stripper and an intercooled absorber. The oxidative degradation of piperazine or organic acids is reduced significantly by inhibitor A, but the production of ethylenediamine is unaffected. The oxidative degradation of piperazine in 7 m MEA/2 m PZ is catalyzed by Cu{sup ++}. The thermal degradation of MEA becomes significant at 120 C. The solubility of potassium sulfate in MEA/PZ solvents is increased at greater CO{sub 2} loading. The best solvent and process configuration, matrix with MDEA/PZ, offers 22% and 15% energy savings over the baseline and improved baseline, respectively, with stripping and compression to 10 MPa. The energy requirement for stripping and compression to 10 MPa is about 20% of the power output from a 500 MW power plant with 90% CO{sub 2} removal. The stripper rate model shows that a ''short and fat'' stripper requires 7 to 15% less equivalent work than a ''tall and skinny'' one. The stripper model was validated with data obtained from pilot plant experiments at the University of Texas with 5m K{sup +}/2.5m PZ and 6.4m K{sup +}/1.6m PZ under normal pressure and vacuum conditions using Flexipac AQ Style 20 structured packing. Experiments with oxidative degradation at low gas rates confirm the effects of Cu{sup +2} catalysis; in MEA/PZ solutions more formate and acetate is produced in the presence of Cu{sup +2}. At 150 C, the half life of 30% MEA with 0.4 moles CO{sub 2}/mole amine is about 2 weeks. At 100 C, less than 3% degradation occurred in two weeks. The solubility of potassium sulfate in MEA solution increases significantly with CO{sub 2} loading and decreases with MEA concentration. The base case corrosion

  7. Simulations of Foils Irradiated by Finite Laser Spots

    NASA Astrophysics Data System (ADS)

    Phillips, Lee

    2006-10-01

    Recent proposed designs (Obenchain et al., Phys. Plasmas 13 056320 (2006)) for direct-drive ICF targets for energy applications involve high implosion velocities with lower laser energies combined with higher irradiances. The use of high irradiances increases the likelihood of deleterious laser plasma instabilities (LPI) that may lead, for example, to the generation of fast electrons. The proposed use of a 248 nm KrF laser is expected to minimize LPI, and this is being studied by experiments on NRL's NIKE laser. Here we report on simulations aimed at designing and interpreting these experiments. The 2d simulations employ a modification of the FAST code to ablate plasma from CH and DT foils using laser pulses with arbitrary spatial and temporal profiles. These include the customary hypergaussian NIKE profile, gaussian profiles, and combinations of these. The simulations model the structure of the ablating plasma and the absorption of the laser light, providing parameters for design of the experiment and indicating where the relevant LPI (two-plasmon, Raman) may be observed.

  8. Influence of successive plasma treatments on PP foils

    NASA Astrophysics Data System (ADS)

    Jacobs, T.; Morent, R.; De Geyter, N.; Leys, C.

    2011-01-01

    Polypropylene (PP) foil is treated with a dielectric barrier discharge (DBD) plasma operating in helium at medium pressure. The influence of exposure to the atmosphere between successive treatments is studied by varying the exposure time. Each PP sample is treated with subsequent treatment steps of 5 s. Between two treatment steps, different procedures are applied: 1) the sample remains in the discharge chamber at medium pressure (under helium atmosphere) for a certain time before it is treated again or 2) the pressure is increased to atmospheric pressure, so the sample remains exposed to atmospheric air for a certain time and afterwards the system is pumped down again to medium pressure before it undergoes a successive helium plasma treatment. The treated samples are analysed using contact angle measurements. The results show that exposure to the atmosphere between two treatment steps leads to a lower contact angle. The longer the exposure time, the lower the contact angle becomes. Another experiment showed that the treatment effect could be gradually removed by applying several short plasma treatments of 1 s to saturated samples. With every short treatment step, the contact angle becomes higher. It is believed that this is due to etching of the surface. In the near future, both atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS) analysis on some selected samples are planned to elucidate the chemical and/or physical nature of the observed phenomena.

  9. A facile method to observe graphene growth on copper foil

    NASA Astrophysics Data System (ADS)

    Yang, Fan; Liu, Yangqiao; Wu, Wei; Chen, Wei; Gao, Lian; Sun, Jing

    2012-11-01

    A novel scanning electron microscope (SEM) method is presented for high contrast identification of each layer of pyramidal graphene domains grown on copper. We obtained SEM images by combining the advantages of the high resolution property of the secondary electron signal and the elemental sensitivity of the backscattering electron signal. Through this method, we investigated the difference in the growth mechanisms of mono-layer and few-layer graphene. Due to different lattice mismatches, both the surface adsorption process and the epitaxial growth process existed under the atmospheric growth conditions. Moreover, the copper oxidation process can be easily discovered. It is obvious from the SEM images that the graphene greatly delayed the oxidation process of the copper surface. Finally, the nucleation and growth speed of graphene domains was found to depend on the linear array distribution of surface ledges and terraces of annealed rolled copper foil. This result explains the linear rows of graphene during the growth process and accords with theoretical results.

  10. Characterization of AN Actively Cooled Metal Foil Thermal Radiation Shield

    NASA Astrophysics Data System (ADS)

    Feller, J. R.; Kashani, A.; Helvensteijn, B. P. M.; Salerno, L. J.

    2010-04-01

    Zero boil-off (ZBO) or reduced boil-off (RBO) systems that involve active cooling of large cryogenic propellant tanks will most likely be required for future space exploration missions. For liquid oxygen or methane, such systems could be implemented using existing high technology readiness level (TRL) cryocoolers. However, for liquid hydrogen temperatures (˜20 K) no such coolers exist. In order to partially circumvent this technology gap, the concept of broad area cooling (BAC) has been developed, whereby a low mass thermal radiation shield could be maintained at temperatures around 100 K by steady circulation of cold pressurized gas through a network of narrow tubes. By this method it is possible to dramatically reduce the radiative heat leak to the 20 K tank. A series of experiments, designed to investigate the heat transfer capabilities of BAC systems, have been conducted at NASA Ames Research Center (ARC). Results of the final experiment in this series, investigating heat transfer from a metal foil film to a distributed cooling line, are presented here.

  11. Calibration of thin-foil manganin gauge in ALOX material

    SciTech Connect

    Benham, R.A.; Weirick, L.J.; Lee, L.M.

    1995-08-01

    The purpose of this program was to develop a calibration curve (stress as a function of change in gauge resistance/gauge resistance) and to obtain gauge repeatability data for Micro-Measurements stripped manganin thin-foiled gauges up to 6.1 GPa in ALOX (42% by volume alumina in Epon 828 epoxy) material. A light-gas gun was used to drive an ALOX impactor into the ALOX target containing four gauges in a centered diamond arrangement. Tilt and velocity of the impactor were measured along with the gauge outputs. Impact stresses from 0.5 to 6.1 GPa were selected in increments of 0.7 GPa with duplicate tests done at 0.5, 3.3 and 6.1 GPa. A total of twelve tests were conducted using ALOX. Three initial tests were done using polymethyl methacrylate (PMMA) as the impactor and target at an impact pressure of 3.0 GPa for comparison of gauge output with analysis and literature values. The installed gauge, stripped of its backing, has a nominal thickness of 5 {micro}m. The thin gauge and high speed instrumentation allowed higher time resolution measurements than can be obtained with manganin wire.

  12. Optical fiber sensors embedded in flexible polymer foils

    NASA Astrophysics Data System (ADS)

    van Hoe, Bram; van Steenberge, Geert; Bosman, Erwin; Missinne, Jeroen; Geernaert, Thomas; Berghmans, Francis; Webb, David; van Daele, Peter

    2010-04-01

    In traditional electrical sensing applications, multiplexing and interconnecting the different sensing elements is a major challenge. Recently, many optical alternatives have been investigated including optical fiber sensors of which the sensing elements consist of fiber Bragg gratings. Different sensing points can be integrated in one optical fiber solving the interconnection problem and avoiding any electromagnetical interference (EMI). Many new sensing applications also require flexible or stretchable sensing foils which can be attached to or wrapped around irregularly shaped objects such as robot fingers and car bumpers or which can even be applied in biomedical applications where a sensor is fixed on a human body. The use of these optical sensors however always implies the use of a light-source, detectors and electronic circuitry to be coupled and integrated with these sensors. The coupling of these fibers with these light sources and detectors is a critical packaging problem and as it is well-known the costs for packaging, especially with optoelectronic components and fiber alignment issues are huge. The end goal of this embedded sensor is to create a flexible optical sensor integrated with (opto)electronic modules and control circuitry. To obtain this flexibility, one can embed the optical sensors and the driving optoelectronics in a stretchable polymer host material. In this article different embedding techniques for optical fiber sensors are described and characterized. Initial tests based on standard manufacturing processes such as molding and laser structuring are reported as well as a more advanced embedding technique based on soft lithography processing.

  13. Foil-less plasma-filled diode for HPM generator

    NASA Astrophysics Data System (ADS)

    Eltchaninov, A. A.; Kovalchuk, B. M.; Kurkan, I. K.; Zherlitsyn, A. A.

    2014-11-01

    Plasma-filled diode regarded as perspective source of electron beam feeding HPM generator of GW power level, comparing to conventional explosive emission vacuum diode. Electron beam generation occurs in plasma double layer, where plasma boundary plays as an anode. It allows cancelling the usage of anode foils or grids in HPM generators with the virtual cathode, which could limit its life time to few shots. The presence of ions in the e-beam drift space could raise the limiting current for a drift space, but it could affect to microwave generation also. Sectioned plasma-filled diode with beam current of about 100 kA, electron beam energy of about 0.5 MV and beam current density of 1-10 kA/cm2 was realized. Cylindrical transport channel with the diameter of 200 mm and the length of about 30 cm was attached to the diode. Beam current measurements in a drift space were performed. Computer simulations of electron beam transport with the presence of ions were carried out with the 2.5D axisymmetric version of PiC-code KARAT. Obtained results would help optimizing electrodynamic system of HPM generator subjected to the presence of ions.

  14. Synthesis of Atomically Thin Boron Films on Copper Foils.

    PubMed

    Tai, Guoan; Hu, Tingsong; Zhou, Yungang; Wang, Xufeng; Kong, Jizhou; Zeng, Tian; You, Yuncheng; Wang, Qin

    2015-12-14

    Two-dimensional boron materials have recently attracted extensive theoretical interest because of their exceptional structural complexity and remarkable physical and chemical properties. However, such 2D boron monolayers have still not been synthesized. In this report, the synthesis of atomically thin 2D γ-boron films on copper foils is achieved by chemical vapor deposition using a mixture of pure boron and boron oxide powders as the boron source and hydrogen gas as the carrier gas. Strikingly, the optical band gap of the boron film was measured to be around 2.25 eV, which is close to the value (2.07 eV) determined by first-principles calculations, suggesting that the γ-B28 monolayer is a fascinating direct band gap semiconductor. Furthermore, a strong photoluminescence emission band was observed at approximately 626 nm, which is again due to the direct band gap. This study could pave the way for applications of two-dimensional boron materials in electronic and photonic devices. PMID:26510179

  15. CHARACTERIZATION OF AN ACTIVELY COOLED METAL FOIL THERMAL RADIATION SHIELD

    SciTech Connect

    Feller, J. R.; Salerno, L. J.; Kashani, A.; Helvensteijn, B. P. M.

    2010-04-09

    Zero boil-off (ZBO) or reduced boil-off (RBO) systems that involve active cooling of large cryogenic propellant tanks will most likely be required for future space exploration missions. For liquid oxygen or methane, such systems could be implemented using existing high technology readiness level (TRL) cryocoolers. However, for liquid hydrogen temperatures (approx20 K) no such coolers exist. In order to partially circumvent this technology gap, the concept of broad area cooling (BAC) has been developed, whereby a low mass thermal radiation shield could be maintained at temperatures around 100 K by steady circulation of cold pressurized gas through a network of narrow tubes. By this method it is possible to dramatically reduce the radiative heat leak to the 20 K tank. A series of experiments, designed to investigate the heat transfer capabilities of BAC systems, have been conducted at NASA Ames Research Center (ARC). Results of the final experiment in this series, investigating heat transfer from a metal foil film to a distributed cooling line, are presented here.

  16. Embedding magnetic field lines in the plasma jet of an exploding radial foil on COBRA

    NASA Astrophysics Data System (ADS)

    Schrafel, Peter; Gourdain, Pierre; Greenly, John; Kusse, Bruce

    2009-11-01

    Previous investigations of exploding radial foils have shown the formation of an axial plasma jet in the early stages of the foil explosion. In this case a thin load foil was pressed at an outer annulus held at ground, and contacted in the center by a small straight rod cathode driven by the 1MA COBRA accelerator. The present experiments look at the effects of inducing a transient magnetic field in the region containing the plasma jet. This induced magnetic field is created in one of two ways: twisting the rod cathode to have a helical coil segment near the foil, or putting an inductive current path in parallel to the straight rod cathode. Of great interest is whether this applied magnetic field can be embedded into the plasma jet and influence its development. The jet is diagnosed visually with laser shadowgraphy and observation of XUV emission. B-dot probes measure the magnetic field strength in the region near the jet.

  17. Role of target material in proton acceleration from thin foils irradiated by ultrashort laser pulses

    NASA Astrophysics Data System (ADS)

    Tayyab, M.; Bagchi, S.; Ramakrishna, B.; Mandal, T.; Upadhyay, A.; Ramis, R.; Chakera, J. A.; Naik, P. A.; Gupta, P. D.

    2014-08-01

    We report on the proton acceleration studies from thin metallic foils of varying atomic number (Z) and thicknesses, investigated using a 45 fs, 10 TW Ti:sapphire laser system. An optimum foil thickness was observed for efficient proton acceleration for our laser conditions, dictated by the laser ASE prepulse and hot electron propagation behavior inside the material. The hydrodynamic simulations for ASE prepulse support the experimental observation. The observed maximum proton energy at different thicknesses for a given element is in good agreement with the reported scaling laws. The results with foils of different atomic number Z suggest that a judicious choice of the foil material can enhance the proton acceleration efficiency, resulting into higher proton energy.

  18. Note: Radial-thrust combo metal mesh foil bearing for microturbomachinery.

    PubMed

    Park, Cheol Hoon; Choi, Sang Kyu; Hong, Doo Euy; Yoon, Tae Gwang; Lee, Sung Hwi

    2013-10-01

    This Note proposes a novel radial-thrust combo metal mesh foil bearing (MMFB). Although MMFBs have advantages such as higher stiffness and damping over conventional air foil bearings, studies related to MMFBs have been limited to radial MMFBs. The novel combo MMFB is composed of a radial top foil, thrust top foils, and a ring-shaped metal mesh damper--fabricated by compressing a copper wire mesh--with metal mesh thrust pads for the thrust bearing at both side faces. In this study, the combo MMFB was fabricated in half-split type to support the rotor for a micro gas turbine generator. The manufacture and assembly process for the half-split-type combo MMFB is presented. In addition, to verify the proposed combo MMFB, motoring test results up to 250,000 rpm and axial displacements as a function of rotational speed are presented. PMID:24182175

  19. LANL Experience Rolling Zr-Clad LEU-10Mo Foils for AFIP-7

    SciTech Connect

    Hammon, Duncan L.; Clarke, Kester D.; Alexander, David J.; Kennedy, Patrick K.; Edwards, Randall L.; Duffield, Andrew N.; Dombrowski, David E.

    2015-05-29

    The cleaning, canning, rolling and final trimming of Low Enriched Uranium-10 wt. pct. Molybdenum (LEU-10Mo) foils for ATR (Advanced Test Reactor) fuel plates to be used in the AFIP-7 (ATR Full Size Plate In Center Flux Trap Position) experiments are summarized. Six Zr-clad foils were produced from two LEU-10Mo castings supplied to Los Alamos National Laboratory (LANL) by Y-12 National Security Complex. Details of cleaning and canning procedures are provided. Hot- and cold-rolling results are presented, including rolling schedules, images of foils in-process, metallography and local compositions of regions of interest, and details of final foil dimensions and process yield. This report was compiled from the slides for the presentation of the same name given by Duncan Hammon on May 12, 2011 at the AFIP-7 Lessons Learned meeting in Salt Lake City, UT, with Los Alamos National Laboratory document number LA-UR 11-02898.

  20. Polarization and collision-induced coherence in the beam-foil light source

    NASA Technical Reports Server (NTRS)

    Liu, C. H.; Bashkin, S.; Church, D. A.

    1974-01-01

    Monatomic systems were excited by the beam-foil method in order to re-examine the possibility that a particular magnetic substate was preferentially populated. O II, Ar II and He I levels were used. The results reveal that: (1) with a tilted foil substantial polarization (up to 15%) may be achieved, (2) the polarization is due to the foil, (3) the foil induces coherence among Zeeman substates with the appearance of quantum beats among these substates and that their coherence is due to the externally applied magnetic field perpendicular to the beam direction, and (4) the angular momentum of the emitted photon is perpendicular to the ion velocity. The possibility for detecting separate effects of alignment and polarization is noted.