On-Board Particulate Filter Failure Prevention and Failure Diagnostics Using Radio Frequency Sensing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sappok, Alex; Ragaller, Paul; Herman, Andrew

The increasing use of diesel and gasoline particulate filters requires advanced on-board diagnostics (OBD) to prevent and detect filter failures and malfunctions. Early detection of upstream (engine-out) malfunctions is paramount to preventing irreversible damage to downstream aftertreatment system components. Such early detection can mitigate the failure of the particulate filter resulting in the escape of emissions exceeding permissible limits and extend the component life. However, despite best efforts at early detection and filter failure prevention, the OBD system must also be able to detect filter failures when they occur. In this study, radio frequency (RF) sensors were used to directlymore » monitor the particulate filter state of health for both gasoline particulate filter (GPF) and diesel particulate filter (DPF) applications. The testing included controlled engine dynamometer evaluations, which characterized soot slip from various filter failure modes, as well as on-road fleet vehicle tests. The results show a high sensitivity to detect conditions resulting in soot leakage from the particulate filter, as well as potential for direct detection of structural failures including internal cracks and melted regions within the filter media itself. Furthermore, the measurements demonstrate, for the first time, the capability to employ a direct and continuous monitor of particulate filter diagnostics to both prevent and detect potential failure conditions in the field.« less

Sensor Technologies for Particulate Detection and Characterization

NASA Technical Reports Server (NTRS)

Greenberg, Paul S.

2008-01-01

Planned Lunar missions have resulted in renewed attention to problems attributable to fine particulates. While the difficulties experienced during the sequence of Apollo missions did not prove critical in all cases, the comparatively long duration of impending missions may present a different situation. This situation creates the need for a spectrum of particulate sensing technologies. From a fundamental perspective, an improved understanding of the properties of the dust fraction is required. Described here is laboratory-based reference instrumentation for the measurement of fundamental particle size distribution (PSD) functions from 2.5 nanometers to 20 micrometers. Concomitant efforts for separating samples into fractional size bins are also presented. A requirement also exists for developing mission compatible sensors. Examples include provisions for air quality monitoring in spacecraft and remote habitation modules. Required sensor attributes such as low mass, volume, and power consumption, autonomy of operation, and extended reliability cannot be accommodated by existing technologies.

Approximation auto-coherente a deux particules, pseudogap et supraconductivite dans le modele de Hubbard attractif

NASA Astrophysics Data System (ADS)

Allen, Steve

2000-10-01

Dans cette these nous presentons une nouvelle methode non perturbative pour le calcul des proprietes d'un systeme de fermions. Notre methode generalise l'approximation auto-coherente a deux particules proposee par Vilk et Tremblay pour le modele de Hubbard repulsif. Notre methode peut s'appliquer a l'etude du comportement pre-critique lorsque la symetrie du parametre d'ordre est suffisamment elevee. Nous appliquons la methode au probleme du pseudogap dans le modele de Hubbard attractif. Nos resultats montrent un excellent accord avec les donnees Monte Carlo pour de petits systemes. Nous observons que le regime ou apparait le pseudogap dans le poids spectral a une particule est un regime classique renormalise caracterise par une frequence caracteristique des fluctuations supraconductrices inferieure a la temperature. Une autre caracteristique est la faible densite de superfluide de cette phase demontrant que nous ne sommes pas en presence de paires preformees. Les resultats obtenus semblent montrer que la haute symetrie du parametre d'ordre et la bidimensionalite du systeme etudie elargissent le domaine de temperature pour lequel le regime pseudogap est observe. Nous argumentons que ce resultat est transposable aux supraconducteurs a haute temperature critique ou le pseudogap apparait a des' temperatures beaucoup plus grandes que la temperature critique. La forte symetrie dans ces systemes pourraient etre reliee a la theorie SO(5) de Zhang. En annexe, nous demontrons un resultat tout recent qui permettrait d'assurer l'auto-coherence entre les proprietes a une et a deux particules par l'ajout d'une dynamique au vertex irreductible. Cet ajout laisse entrevoir la possibilite d'etendre la methode au cas d'une forte interaction.

Visual detection of particulates in processed meat products by x ray

NASA Astrophysics Data System (ADS)

Schatzki, Thomas F.; Young, Richard; Haff, Ron P.; Eye, J.; Wright, G.

1995-01-01

A test has been run to study the efficacy of detecting particulate contaminants in processed meat samples by manual observation of line-scanned x-ray images. Six hundred processed product samples arriving over a 3 month period at a national USDA-FSIS laboratory were scanned at 230 cm2sec with 0.5 X 0.5 mm resolution, using 50 KV, 13 ma excitation, with digital interfacing and image correction. Images were inspected off-line, using interactive image enhancement. Forty percent of the samples were spiked, blind to the analyst, in order to establish the manual recognition rate as a function of sample thickness [1 - 10 cm] and texture of the x-ray image [smooth/textured], as well as spike composition [wood/bone/glass], size [1 - 4 mm] and shape [splinter/round]. The results have been analyzed using maximum likelihood logistic regression. In meat packages less than 6 cm thick, 2 mm bone chips are easily recognized, 1 mm glass splinters with some difficulty, while wood is generally missed even at 4 mm. Operational feasibility in a time-constrained setting has bee confirmed. One half percent of the samples arriving from the field contained bone slivers > 1 cm long, one half percent contained metallic material, while 4% contained particulates exceeding 3.2 mm in size. All of the latter appeared to be bone fragments.

Caracterisation pratique des systemes quantiques et memoires quantiques auto-correctrices 2D

NASA Astrophysics Data System (ADS)

Landon-Cardinal, Olivier

Cette these s'attaque a deux problemes majeurs de l'information quantique: - Comment caracteriser efficacement un systeme quantique? - Comment stocker de l'information quantique? Elle se divise done en deux parties distinctes reliees par des elements techniques communs. Chacune est toutefois d'un interet propre et se suffit a elle-meme. Caracterisation pratique des systemes quantiques. Le calcul quantique exige un tres grand controle des systemes quantiques composes de plusieurs particules, par exemple des atomes confines dans un piege electromagnetique ou des electrons dans un dispositif semi-conducteur. Caracteriser un tel systeme quantique consiste a obtenir de l'information sur l'etat grace a des mesures experimentales. Or, chaque mesure sur le systeme quantique le perturbe et doit done etre effectuee apres avoir reprepare le systeme de facon identique. L'information recherchee est ensuite reconstruite numeriquement a partir de l'ensemble des donnees experimentales. Les experiences effectuees jusqu'a present visaient a reconstruire l'etat quantique complet du systeme, en particulier pour demontrer la capacite de preparer des etats intriques, dans lesquels les particules presentent des correlations non-locales. Or, la procedure de tomographie utilisee actuellement n'est envisageable que pour des systemes composes d'un petit nombre de particules. Il est donc urgent de trouver des methodes de caracterisation pour les systemes de grande taille. Dans cette these, nous proposons deux approches theoriques plus ciblees afin de caracteriser un systeme quantique en n'utilisant qu'un effort experimental et numerique raisonnable. - La premiere consiste a estimer la distance entre l'etat realise en laboratoire et l'etat cible que l'experimentateur voulait preparer. Nous presentons un protocole, dit de certification, demandant moins de ressources que la tomographie et tres efficace pour plusieurs classes d'etats importantes pour l'informatique quantique. - La seconde

Le role du phytoplancton de petite taille (<20 mum) dans les variations des proprietes optiques des eaux du Saint-Laurent

NASA Astrophysics Data System (ADS)

Mas, Sebastien

Les mesures satellitaires de couleur des oceans sont largement determinees par les proprietes optiques inherentes (IOPs) des eaux de surface. D'autre part, le phytoplancton de petite taille (<20 mum) est le plus souvent dominant dans les oceans, et peut donc etre une source importante de variation des IOPs dans les oceans. Dans ce contexte, le but principal de ce doctorat etait de definir l'impact du phytoplancton (<20 mum) sur les variations des proprietes optiques de l'Estuaire et du Golfe du Saint-Laurent (Canada). Afin d'atteindre cet objectif, il etait necessaire de determiner en milieu controle les facteurs de variabilite des proprietes optiques cellulaires et des IOPs du phytoplancton (<20 mum) des eaux du Saint-Laurent, et d'evaluer la contribution du phytoplancton (<20 mum) aux proprietes optiques totales des eaux du Saint-Laurent. Des experiences en laboratoire ont montre que les variations des proprietes optiques des cellules phytoplanctoniques soumises a un cycle jour-nuit, ainsi qu'a des changements concomitants d'intensite lumineuse, peuvent contribuer significativement a la variabilite des proprietes optiques observee en milieu naturel. D'autres experiences ont, quant a elles, mis en evidence que les variations des proprietes optiques des cellules phytoplanctoniques dues aux phases de croissance peuvent alterer les IOPs des oceans, particulierement pendant les periodes de floraison. De plus, la presence de bacteries et de particules detritiques peut egalement affecter la variabilite des IOPs totales, notamment la diffusion. Au printemps, dans l'Estuaire et le Golfe du Saint-Laurent, la contribution du phytoplancton <20 mum aux IOPs presentait des differences regionales evidentes pour les proprietes d'absorption et de diffusion. En plus de la variabilite spatiale, les proprietes optiques cellulaires presentaient des variations journalieres, et ce particulierement pour le picophytoplancton. Enfin, la plupart des differences observees dans les

Matériaux pour la dépollution des gaz d'échappement automobile

NASA Astrophysics Data System (ADS)

Mouaddib-Moral, N.; Gauthier, C.

2002-04-01

Les premières législations antipollution ont été mises en place suite à la détection, aux Etats Unis plus particulièrement en Californie, du smog photochimique et des pluies acides, néfastes pour la faune et la flore. Les estimations de la contribution de l'automobile aux émissions de composés, considérés comme précurseurs de ces phénomènes, ont été suffisantes pour provoquer la mise en place de normes draconiennes en matière d'émissions automobiles. Les matériaux catalytiques ont été évalués en tant que solution possible pour réduire les émissions à l'échappement. En Europe, l'utilisation des catalyseurs trois voies a été généralisée sur les véhicules essence fonctionnant à richesse stoechiométrique à partir de 1993. Une nouvelle génération de catalyseurs appelée piège à oxydes d'azote (NOx) est maintenant nécessaire pour le post-traitement des gaz d'échappement des motorisations à essence fonctionnant en mélange pauvre (combustion en présence d'un excès d'oxygène) pour diminuer la consommation et par conséquent réduire les émissions du CO2 connu pour son impact sur l'effet de serre. La dépollution des moteurs diesel via un catalyseur d'oxydation a été généralisée en Europe depuis 1996. La sévérisation des normes européennes impose pour les moteurs diesel le recours à des matériaux spécifiques pour le traitement des oxydes d'azotes et des particules par l'intermédiaire de filtres à particules dont l'efficacité de filtration est supérieure à 95%, mais doivent subir des régénérations périodiques.

Effets des electrons secondaires sur l'ADN

NASA Astrophysics Data System (ADS)

Boudaiffa, Badia

Les interactions des electrons de basse energie (EBE) representent un element important en sciences des radiations, particulierement, les sequences se produisant immediatement apres l'interaction de la radiation ionisante avec le milieu biologique. Il est bien connu que lorsque ces radiations deposent leur energie dans la cellule, elles produisent un grand nombre d'electrons secondaires (4 x 104/MeV), qui sont crees le long de la trace avec des energies cinetiques initiales bien inferieures a 20 eV. Cependant, il n'y a jamais eu de mesures directes demontrant l'interaction de ces electrons de tres basse energie avec l'ADN, du principalement aux difficultes experimentales imposees par la complexite du milieu biologique. Dans notre laboratoire, les dernieres annees ont ete consacrees a l'etude des phenomenes fondamentaux induits par impact des EBE sur differentes molecules simples (e.g., N2, CO, O2, H2O, NO, C2H 4, C6H6, C2H12) et quelques molecules complexes dans leur phase solide. D'autres travaux effectues recemment sur des bases de l'ADN et des oligonucleotides ont montre que les EBE produisent des bris moleculaires sur les biomolecules. Ces travaux nous ont permis d'elaborer des techniques pour mettre en evidence et comprendre les interactions fondamentales des EBE avec des molecules d'interet biologique, afin d'atteindre notre objectif majeur d'etudier l'effet direct de ces particules sur la molecule d'ADN. Les techniques de sciences des surfaces developpees et utilisees dans les etudes precitees peuvent etre etendues et combinees avec des methodes classiques de biologie pour etudier les dommages de l'ADN induits par l'impact des EBE. Nos experiences ont montre l'efficacite des electrons de 3--20 eV a induire des coupures simple et double brins dans l'ADN. Pour des energies inferieures a 15 eV, ces coupures sont induites par la localisation temporaire d'un electron sur une unite moleculaire de l'ADN, ce qui engendre la formation d'un ion negatif transitoire

Omega-3 Fatty Acid Attenuates Cardiovascular Effects in Healthy Older Volunteers Exposed to Concentrated Ambient Fine and UltrafineParticulate Matter

EPA Science Inventory

Rationale: Ambient particulate matter (PM) exposure has been associated with adverse cardiovascular effects. A recent epidemiology study reported that omega-3 polyunsaturated fatty acid (fish oil) supplementation blunted the response of study participants to PM. Our study was des...

Laser Based Stand-Off Detection of Biological Agents (detection a distance des agents biologiques a l’aide du laser)

DTIC Science & Technology

2010-02-01

overview of their respective national up-date. Dr. Roy presented a new technique for evaluating the bioaerosol particle size based on a multiple...Field-of-View LIDAR technique . Mr. Levesque from INO gave an overview of their expertise in LIDAR and biophotonics. Dr. Chin from Laval University gave... techniques have the potential to detect particulate aerosols remotely at distances of many kilometres [1]. They can provide spatially resolved

Particulate contamination spectrometer. Volume 1: Technical report

NASA Technical Reports Server (NTRS)

Schmitt, R. J.; Boyd, B. A.; Linford, R. M. F.

1975-01-01

A laser particulate spectrometer (LPS) system was developed to measure the size and speed distributions of particulate (dusts, aerosols, ice particles, etc.) contaminants. Detection of the particulates was achieved by means of light scattering and extinction effects using a single laser beam to cover a size range of 0.8 to 275 microns diameter and a speed range of 0.2 to 20 meter/second. The LPS system was designed to operate in the high vacuum environment of a space simulation chamber with cold shroud temperatures ranging from 77 to 300 K.

Visual detection of particulates in x-ray images of processed meat products

NASA Astrophysics Data System (ADS)

Schatzki, Thomas F.; Young, Richard; Haff, Ron P.; Eye, J.; Wright, G.

1996-08-01

A study was conducted to test the efficacy of detecting particulate contaminants in processed meat samples by visual observation of line-scanned x-ray images. Six hundred field- collected processed-product samples were scanned at 230 cm2/s using 0.5 X 0.5-mm resolution and 50 kV, 13 mA excitation. The x-ray images were image corrected, digitally stored, and inspected off-line, using interactive image enhancement. Forty percent of the samples were spiked with added contaminants to establish the visual recognition of contaminants as a function of sample thickness (1 to 10 cm), texture of the x-ray image (smooth/textured), spike composition (wood/bone/glass), size (0.1 to 0.4 cm), and shape (splinter/round). The results were analyzed using a maximum likelihood logistic regression method. In packages less than 6 cm thick, 0.2-cm-thick bone chips were easily recognized, 0.1-cm glass splinters were recognized with some difficulty, while 0.4-cm-thick wood was generally missed. Operational feasibility in a time-constrained setting was confirmed. One half percent of the samples arriving from the field contained bone slivers > 1 cm long, 1/2% contained metallic material, while 4% contained particulates exceeding 0.3 cm in size. All of the latter appeared to be bone fragments.

Radio Frequency Sensing of Particulate Matter Accumulation on a Gasoline Particulate Filter

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parks, James; Prikhodko, Vitaly Y.; Sappok, Alex

Filter Sensing Technology’s radio frequency (RF) sensor for particulate filter on-board diagnostics (OBD) was studied on a lean gasoline engine at the National Transportation Research Center (NTRC) at Oak Ridge National Laboratory (ORNL). The response of the RF sensor to particulate matter (PM) or “soot” accumulation on the gasoline particulate filter (GPF) installed in the engine exhaust was evaluated. In addition, end plugs of the GPF were purposely removed, and subsequent changes to the RF sensor measured soot loading on the GPF were characterized. Results from the study showed that the RF sensor can accurately measure soot accumulation on amore » GPF; furthermore, the predicted decreased soot accumulation due to plug removal was detected by the RF sensor. Overall, the studies were short and preliminary in nature; however, clearly, the RF sensor demonstrated the capability of measuring GPF soot loading at a level suitable for use in lean gasoline engine emission control OBD and control.« less

Explorer : des clés pour mieux comprendre la matière

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ellis, Jonathan R.

2011-02-14

Will the LHC upset theories of the infinitely small? Physicists would like the accelerator to shake the standard model. This theory of elementary particles and forces leaves many gray areas. The LHC and its experiments have been designed to enlighten them. [Le LHC va-t-il bouleverser les théories de l'infiniment petit ? Les physiciens aimeraient que l'accélérateur fasse trembler le modèle standard. Cette théorie des particules élémentaires et des forces laisse de nombreuses zones d'ombre. Le LHC et ses expériences ont été conçus pour les éclairer.

Dynamique de nanobulles et nanoplasmas generes autour de nanoparticules plasmoniques irradiees par des impulsions ultracourtes

NASA Astrophysics Data System (ADS)

Dagallier, Adrien

L'emergence des lasers a impulsion ultrabreves et des nanotechnologies a revolutionne notre perception et notre maniere d'interagir avec l'infiniment petit. Les gigantesques intensites generees par ces impulsions plus courtes que les temps de relaxation ou de diffusion du milieu irradie induisent de nombreux phenomenes non-lineaires, du doublement de frequence a l'ablation, dans des volumes de dimension caracteristique de l'ordre de la longueur d'onde du laser. En biologie et en medecine, ces phenomenes sont utilises a des fins d'imagerie multiphotonique ou pour detruire des tissus vivants. L'introduction de nanoparticules plasmoniques, qui concentrent le champ electromagnetique incident dans des regions de dimensions nanometriques, jusqu'a une fraction de la longueur d'onde, amplifie les phenomenes non-lineaires tout en offrant un controle beaucoup plus precis de la deposition d'energie, ouvrant la voie a la detection de molecules individuelles en solution et a la nanochirurgie. La nanochirurgie repose principalement sur la formation d'une bulle de vapeur a proximite d'une membrane cellulaire. Cette bulle de vapeur perce la membrane de maniere irreversible,entrainant la cellule a sa mort, ou la perturbe temporairement, ce qui permet d'envisager de faire penetrer dans la cellule des medicaments ou des brins d'ADN pour de la therapie genique. C'est principalement la taille de la bulle qui va decider de l'issue de l'irradiation laser. Il est donc necessaire de controler finement les parametres du laser et la geometrie de la nanoparticule afin d'atteindre l'objectif fixe. Le moyen le plus direct a l'heure actuelle de valider un ensemble de conditions experimentales est de realiser l'experience en laboratoire,ce qui est long et couteux. Les modeles de dynamique de bulle existants ne prennent pas en compte les parametres de l'irradiation et ajustent souvent leurs conditions initiales a partir de leurs mesures experimentales, ce qui limite la portee du modele au cas pour

Apparatus for real-time airborne particulate radionuclide collection and analysis

DOEpatents

Smart, John E.; Perkins, Richard W.

2001-01-01

An improved apparatus for collecting and analyzing an airborne particulate radionuclide having a filter mounted in a housing, the housing having an air inlet upstream of the filter and an air outlet downstream of the filter, wherein an air stream flows therethrough. The air inlet receives the air stream, the filter collects the airborne particulate radionuclide and permits a filtered air stream to pass through the air outlet. The improvement which permits real time counting is a gamma detecting germanium diode mounted downstream of the filter in the filtered air stream. The gamma detecting germanium diode is spaced apart from a downstream side of the filter a minimum distance for a substantially maximum counting detection while permitting substantially free air flow through the filter and uniform particulate radionuclide deposition on the filter.

Characterization of functional groups of airborne particulate matter

NASA Astrophysics Data System (ADS)

Baitimirova, M.; Katkevics, J.; Baumane, L.; Bakis, E.; Viksna, A.

2013-12-01

Particulate matter of organic combustibles burning consists of various hydrocarbons and radicals, which may cause harmful impact to human health. In this study solid particulate matter were collected on the filters from burning of various combustibles in a burning chamber and from atmosphere of city of Riga by dichotomous impactor. FTIR spectra were obtained before and after samples' treatment. Absorptions associated with aliphatic and aromatic hydrocarbons and alcohol functional groups were observed in the FTIR spectra. Free radicals of particulate matter were detected by electron paramagnetic resonance (EPR).

Polarization signatures of airborne particulates

NASA Astrophysics Data System (ADS)

Raman, Prashant; Fuller, Kirk A.; Gregory, Don A.

2013-07-01

Exploratory research has been conducted with the aim of completely determining the polarization signatures of selected particulates as a function of wavelength. This may lead to a better understanding of the interaction between electromagnetic radiation and such materials, perhaps leading to the point detection of bio-aerosols present in the atmosphere. To this end, a polarimeter capable of measuring the complete Mueller matrix of highly scattering samples in transmission and reflection (with good spectral resolution from 300 to 1100 nm) has been developed. The polarization properties of Bacillus subtilis (surrogate for anthrax spore) are compared to ambient particulate matter species such as pollen, dust, and soot. Differentiating features in the polarization signatures of these samples have been identified, thus demonstrating the potential applicability of this technique for the detection of bio-aerosol in the ambient atmosphere.

A Small Angle Scattering Sensor System for the Characterization of Combustion Generated Particulate

NASA Technical Reports Server (NTRS)

Feikema, Douglas A.; Kim, W.; Sivathanu, Yudaya

2007-01-01

One of the critical issues for the US space program is fire safety of the space station and future launch vehicles. A detailed understanding of the scattering signatures of particulate is essential for the development of a false alarm free fire detection system. This paper describes advanced optical instrumentation developed and applied for fire detection. The system is being designed to determine four important physical properties of disperse fractal aggregates and particulates including size distribution, number density, refractive indices, and fractal dimension. Combustion generated particulate are the primary detection target; however, in order to discriminate from other particulate, non-combustion generated particles should also be characterized. The angular scattering signature is measured and analyzed using two photon optical laser scattering. The Rayleigh-Debye-Gans (R-D-G) scattering theory for disperse fractal aggregates is utilized. The system consists of a pulsed laser module, detection module and data acquisition system and software to analyze the signals. The theory and applications are described.

Recognition of iron ions by carbazole-desferrioxamine fluorescent sensor and its application in total iron detection in airbone particulate matter.

PubMed

Delattre, François; Cazier-Dennin, Francine; Leleu, Ludovic; Dewaele, Dorothée; Landy, David; Mallard, Isabelle; Danjou, Pierre-Edouard

2015-11-01

This work reports on an efficient microwave irradiation synthesis of a new fluorescent chemosensor based on desferrioxamine B (DFO-B) and carbazole moiety. Furthermore, this novel chemosensor was employed for a comparative study of real environmental samples of airbone particulate matter collected from Dunkirk (Northern of France). Among selected relevant metal cations present in its airbone particulate matter, such as Na(+), K(+), Mg(2+), Ca(2+), Al(3+), Cr(3+), Mn(2+) and Zn(2+), this molecular device proved to be outstandingly sensitive toward Fe(3+) with a limit of detection of 1.49 ppb (2.1×10(-8) M) in methanol allowing the estimation of total iron in atmospheric particles. Copyright © 2015 Elsevier B.V. All rights reserved.

Particulate Emissions Hazards Associated with Fueling Heat Engines

NASA Technical Reports Server (NTRS)

Hendricks, Robert C.; Bushnell, Dennis M.

2010-01-01

All hydrocarbon- (HC-) fueled heat engine exhaust (tailpipe) emissions (<10 to 140 nm) contribute as health hazards, including emissions from transportation vehicles (e.g., aircraft) and other HC-fueled power systems. CO2 emissions are tracked, and when mapped, show outlines of major transportation routes and cities. Particulate pollution affects living tissue and is found to be detrimental to cardiovascular and respiratory systems where ultrafine particulates directly translocate to promote vascular system diseases potentially detectable as organic vapors. This paper discusses aviation emissions, fueling, and certification issues, including heat engine emissions hazards, detection at low levels and tracking of emissions, and alternate energy sources for general aviation.

Continuous Particulate Filter State of Health Monitoring Using Radio Frequency Sensing

DOE PAGES

Sappok, Alexander; Ragaller, Paul; Herman, Andrew; ...

2018-04-03

Reliable means for on-board detection of particulate filter failures or malfunctions are needed to meet diagnostics (OBD) requirements. Detecting these failures, which result in tailpipe particulate matter (PM) emissions exceeding the OBD limit, over all operating conditions is challenging. Current approaches employ differential pressure sensors and downstream PM sensors, in combination with particulate filter and engine-out soot models. These conventional monitors typically operate over narrowly-defined time windows and do not provide a direct measure of the filter’s state of health. In contrast, radio frequency (RF) sensors, which transmit a wireless signal through the filter substrate provide a direct means formore » interrogating the condition of the filter itself. Here, this study investigated the use of RF sensors for the continuous measurement of filter trapping efficiency, which was compared to downstream measurements with an AVL Microsoot Sensor, and a PM sampling probe simulating the geometry and installation configuration of a conventional PM sensor. The study included several particulate filter failure modes, both above and below the OBD threshold. Finally, the results confirmed the use of RF sensors to provide a direct and continuous measure of the particulate filter’s state of health over a range of typical in-use operating conditions, thereby significantly increasing the time window over which filter failures may be detected.« less

Continuous Particulate Filter State of Health Monitoring Using Radio Frequency Sensing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sappok, Alexander; Ragaller, Paul; Herman, Andrew

Reliable means for on-board detection of particulate filter failures or malfunctions are needed to meet diagnostics (OBD) requirements. Detecting these failures, which result in tailpipe particulate matter (PM) emissions exceeding the OBD limit, over all operating conditions is challenging. Current approaches employ differential pressure sensors and downstream PM sensors, in combination with particulate filter and engine-out soot models. These conventional monitors typically operate over narrowly-defined time windows and do not provide a direct measure of the filter’s state of health. In contrast, radio frequency (RF) sensors, which transmit a wireless signal through the filter substrate provide a direct means formore » interrogating the condition of the filter itself. Here, this study investigated the use of RF sensors for the continuous measurement of filter trapping efficiency, which was compared to downstream measurements with an AVL Microsoot Sensor, and a PM sampling probe simulating the geometry and installation configuration of a conventional PM sensor. The study included several particulate filter failure modes, both above and below the OBD threshold. Finally, the results confirmed the use of RF sensors to provide a direct and continuous measure of the particulate filter’s state of health over a range of typical in-use operating conditions, thereby significantly increasing the time window over which filter failures may be detected.« less

Detection of particulate air pollution plumes from major point sources using ERTS-1 imagery

NASA Technical Reports Server (NTRS)

Lyons, W. A.; Pease, S. R.

1973-01-01

The Earth Resources Technology Satellite (ERTS-1) launched by NASA in July 1972 has been providing thousands of high resolution multispectral images of interest to geographers, cartographers, hydrologists, and agroculturists. It has been found possible to detect the long-range (over 50 km) transport of suspected particulate plumes from the Chicago-Gary steel mill complex over Lake Michigan. The observed plumes are readily related to known steel mills, a cement plant, refineries, and fossil-fuel power plants. This has important ramifications when discussing the interregional transport of atmospheric pollutants. Analysis reveals that the Multispectral Scanner Band 5 (0.6 to 0.7 micrometer) provides the best overall contrast between the smoke and the underlying water surface.

Impact de la preparation des anodes crues et des conditions de cuisson sur la fissuration dans des anodes denses

NASA Astrophysics Data System (ADS)

Amrani, Salah

electrique a ete suivie et l'etape de devolatilisation a ete identifiee. Certaines anodes ont ete cuites a differents taux de chauffage (bas, moyen, eleve et un autre combine) dans l'objectif de trouver les meilleures conditions de cuisson en vue de minimiser la fissuration. D'autres anodes ont ete cuites a differents niveaux de cuisson, cela dans le but d'identifier a quelle etape de l'operation de cuisson la fissuration commence a se developper. Apres la cuisson, les anodes ont ete recuperees pour, a nouveau, faire leur caracterisation par les memes techniques utilisees precedemment. L'objectif principal de cette partie etait de reveler l'impact de differents parametres sur le probleme de fissuration, qui sont repartis sur toute la chaine de production des anodes. Le pourcentage de megots, la quantite de brai et la distribution des particules sont des facteurs importants a considerer pour etudier l'effet de la matiere premiere sur le probleme de la fissuration. Concernant l'effet des parametres du procede de fabrication sur le meme probleme, le temps de vibration, la pression de compaction et le procede de refroidissement ont ete a la base de cette etude. Finalement, l'influence de la phase de cuisson sur l'apparition de la fissuration a ete prise en consideration par l'intermediaire du taux de chauffage et du niveau de cuisson. Les travaux realises au niveau industriel ont ete faits lors d'une campagne de mesure dans le but d'evaluer la qualite des anodes de carbone en general et l'investigation du probleme de fissuration en particulier. Ensuite, il s'agissait de reveler les effets de differents parametres sur le probleme de la fissuration. Vingt-quatre anodes cuites ont ete utilisees. Elles ont ete fabriquees avec differentes matieres premieres (brai, coke, megots) et sous diverses conditions (pression, temps de vibration). Le parametre de la densite de fissuration a ete calcule en se basant sur l'inspection visuelle de la fissuration des carottes. Cela permet de

Particulate matter sensor with a heater

DOEpatents

Hall, Matthew [Austin, TX

2011-08-16

An apparatus to detect particulate matter. The apparatus includes a sensor electrode, a shroud, and a heater. The electrode measures a chemical composition within an exhaust stream. The shroud surrounds at least a portion of the sensor electrode, exclusive of a distal end of the sensor electrode exposed to the exhaust stream. The shroud defines an air gap between the sensor electrode and the shroud and an opening toward the distal end of the sensor electrode. The heater is mounted relative to the sensor electrode. The heater burns off particulate matter in the air gap between the sensor electrode and the shroud.

Explorer : des clés pour mieux comprendre la matière

ScienceCinema

Ellis, Jonathan R.

2018-01-12

Will the LHC upset theories of the infinitely small? Physicists would like the accelerator to shake the standard model. This theory of elementary particles and forces leaves many gray areas. The LHC and its experiments have been designed to enlighten them. [Le LHC va-t-il bouleverser les théories de l'infiniment petit ? Les physiciens aimeraient que l'accélérateur fasse trembler le modèle standard. Cette théorie des particules élémentaires et des forces laisse de nombreuses zones d'ombre. Le LHC et ses expériences ont été conçus pour les éclairer.

Atmospheric particulate measurements in Norfolk, Virginia

NASA Technical Reports Server (NTRS)

Storey, R. W., Jr.; Sentell, R. J.; Woods, D. C.; Smith, J. R.; Harris, F. S., Jr.

1975-01-01

Characterization of atmospheric particulates was conducted at a site near the center of Norfolk, Virginia. Air quality was measured in terms of atmospheric mass loading, particle size distribution, and particulate elemental composition for a period of 2 weeks. The objectives of this study were (1) to establish a mean level of air quality and deviations about this mean, (2) to ascertain diurnal changes or special events in air quality, and (3) to evaluate instrumentation and sampling schedules. Simultaneous measurements were made with the following instruments: a quartz crystal microbalance particulate monitor, a light-scattering multirange particle counter, a high-volume air sampler, and polycarbonate membrane filters. To assess the impact of meteorological conditions on air quality variations, continuous data on temperature, relative humidity, wind speed, and wind direction were recorded. Particulate elemental composition was obtained from neutron activation and scanning electron microscopy analyses of polycarbonate membrane filter samples. The measured average mass loading agrees reasonably well with the mass loadings determined by the Virginia State Air Pollution Control Board. There are consistent diurnal increases in atmospheric mass loading in the early morning and a sample time resolution of 1/2 hour seems necessary to detect most of the significant events.

Etude de la dynamique des porteurs dans des nanofils de silicium par spectroscopie terahertz

NASA Astrophysics Data System (ADS)

Beaudoin, Alexandre

Ce memoire presente une etude des proprietes de conduction electrique et de la dynamique temporelle des porteurs de charges dans des nanofils de silicium sondes par rayonnement terahertz. Les cas de nanofils de silicium non intentionnellement dopes et dopes type n sont compares pour differentes configurations du montage experimental. Les mesures de spectroscopie terahertz en transmission montre qu'il est possible de detecter la presence de dopants dans les nanofils via leur absorption du rayonnement terahertz (˜ 1--12 meV). Les difficultes de modelisation de la transmission d'une impulsion electromagnetique dans un systeme de nanofils sont egalement discutees. La detection differentielle, une modification au systeme de spectroscopie terahertz, est testee et ses performances sont comparees au montage de caracterisation standard. Les instructions et des recommendations pour la mise en place de ce type de mesure sont incluses. Les resultats d'une experience de pompe optique-sonde terahertz sont egalement presentes. Dans cette experience, les porteurs de charge temporairement crees suite a l'absorption de la pompe optique (lambda ˜ 800 nm) dans les nanofils (les photoporteurs) s'ajoutent aux porteurs initialement presents et augmentent done l'absorption du rayonnement terahertz. Premierement, l'anisotropie de l'absorption terahertz et de la pompe optique par les nanofils est demontree. Deuxiemement, le temps de recombinaison des photoporteurs est etudie en fonction du nombre de photoporteurs injectes. Une hypothese expliquant les comportements observes pour les nanofils non-dopes et dopes-n est presentee. Troisiemement, la photoconductivite est extraite pour les nanofils non-dopes et dopes-n sur une plage de 0.5 a 2 THz. Un lissage sur la photoconductivite permet d'estimer le nombre de dopants dans les nanofils dopes-n. Mots-cles: nanofil, silicium, terahertz, conductivite, spectroscopie, photoconductivite.

Using the verona coding definitions of emotional sequences (VR-CoDES) and health provider responses (VR-CoDES-P) in the dental context.

PubMed

Wright, Alice; Humphris, Gerry; Wanyonyi, Kristina L; Freeman, Ruth

2012-10-01

To show if cues, concerns and provider responses (defined in VR-CoDES and VR-CoDES-P manuals) are present, can be reliably coded and require additional advice for adoption in a dental context. Thirteen patients in a dental practice setting were videoed with either their dentist or hygienist and dental nurse present in routine treatment sessions. All utterances were coded using the Verona systems: VR-CoDES and the VR-CoDES-P. Rates of cue, concerns and provider responses described and reliability tested. The VR-CoDES and VR-CoDES-P were successfully applied in the dental context. The intra-rater ICCs for the detection of cues and concerns and provider response were acceptable and above 0.75. A similar satisfactory result was found for the inter-rater reliability. The VR-CoDES and the VR-CoDES-P are applicable in the dental setting with minor supporting guidelines and show evidence of reliable coding. The VR-CoDES and the VR-CoDES-P may be helpful tools for analysing patient cues and concerns and the dental professionals' responses in the dental context. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

Real Time Intrusion Detection (la detection des intrusions en temps reel)

DTIC Science & Technology

2003-06-01

prometteuses actuelles et nouvelles, susceptibles d’être utilisées pour des applications temps réel, et laisse prévoir ainsi les technologies et les...components, to survivability, as a risk management problem requiring the involvement of the whole organization to support the survival of the organization’s...this topic. In all fairness , until recently “reaction” has not been part of IDS’s functionality. Above all and as stated previously, traditional RT

Portable detection of trace metals in airborne particulates and sediments via μPADs and smartphone.

PubMed

Jia, Yuan; Dong, Hui; Zheng, Jianping; Sun, Hao

2017-11-01

Particulate matter (PM), a key indicator of air pollution by natural and anthropogenic activities, contributes to a wide spectrum of diseases that lead to a shortening of life expectancy. It has been recognized that trace metals in airborne PM are highly toxic and can be correlated with lesion in respiratory, gastrointestinal, immunological, and hematological systems. Traditional methods for trace metal assay require sophisticated instrumentations and highly trained operators in centralized laboratories. In this work, by integrating the technologies of microfluidic paper-based analytical devices, additive manufacturing, smartphone, and colorimetric sensing, we developed the first smartphone based paper microfluidic platform for portable, disposable, and quantitative measurements of cobalt (Co), copper (Cu), and iron (Fe) in ambient air and street sediments. On a single A4-sized paper, 48 devices were fabricated in under 30 s with a total cost of ∼$1.9. On each device, 12 reaction units were patterned and used for colorimetric tests. Particulate samples from urban ambient air and street sediments were collected, processed, and analyzed. Signals of the on-chip complexation product were recorded using a smartphone camera and processed by a self-developed app on an iOS system. For precisely controlling the object distance, chip position, and luminance, a hand-held 3D cellphone housing was designed and printed. The detection limits of Co, Cu, and Fe were determined to be 8.2, 45.8, and 186.0 ng, while the linear dynamic ranges were calculated to be 8.2-81.6, 45.8-4.58 × 10 2 , and 1.86 × 10 2 -1.86 × 10 3  ng, representing a practically relevant device performance with a significant reduction in the detection cost and time consumption. Trace metals in ambient air and sediments of two cities in China have been quantified portably, thus demonstrating the utility of our system in improving strategies for air pollution control in low-resource settings.

Mineralogy and geochemistry of atmospheric particulates in western Iran

NASA Astrophysics Data System (ADS)

Ahmady-Birgani, Hesam; Mirnejad, Hassan; Feiznia, Sadat; McQueen, Ken G.

2015-10-01

This study investigates the mineralogy and physico-chemical properties of atmospheric particulates collected at Abadan (southwestern Iran) near the Persian Gulf coast and Urmia (northwestern Iran) during ambient and dust events over 6 months (winter 2011; spring 2012). Particle sizes collected were: TSP (total suspended particulates); PM10 (particulates <10 μm); and PM2.5 (particulates <2.5 μm). Minerals were identified using X-ray diffraction (XRD); particle morphology and composition were examined by scanning electron microscopy and energy dispersive X-ray spectroscopy (SEM-EDX). Major minerals detected are calcite, quartz, clay minerals and gypsum, with relative abundance related to sampling site, collection period, wind direction, sampling head, and total sample amount. The anomalously high calcite content appears a characteristic feature originated from calcareous soils of the region. SEM observations indicated a wide range of particle morphologies over the 1-50 μm size range, with spherical, platy, cubic, elongate and prismatic shapes and rounding from angular to rounded. Energy dispersive X-ray analysis of TSP samples from both sites for non-dusty periods indicated that the sampled mineral suite contained Al, Mg, Na, Cl, P, S, Ca, K, Fe, Ti, and Si, mostly reflecting calcite, quartz, aluminosilicates, clays, gypsum and halite. Additionally, As, Pb, Zn, Mn, Sc, Nd, W, Ce, La, Ba and Ni were detected in TSP, PM10 and PM2.5 samples collected during dust events.

Déprescription des agonistes des récepteurs des benzodiazépines

PubMed Central

Pottie, Kevin; Thompson, Wade; Davies, Simon; Grenier, Jean; Sadowski, Cheryl A.; Welch, Vivian; Holbrook, Anne; Boyd, Cynthia; Swenson, Robert; Ma, Andy; Farrell, Barbara

2018-01-01

Résumé Objectif Formuler des lignes directrices fondées sur les données probantes visant à aider les cliniciens à décider du moment et de la façon sécuritaire de réduire la dose des agonistes des récepteurs des benzodiazépines (BZRA) pour mettre fin au traitement; se concentrer sur le niveau le plus élevé des données disponibles et obtenir les commentaires des professionnels de première ligne durant le processus de rédaction, de révision et d’adoption des lignes directrices. Méthodes L’équipe comptait 8 cliniciens (1 médecin de famille, 2 psychiatres, 1 psychologue clinique, 1 pharmacologue clinique, 2 pharmaciennes cliniques et 1 gériatre) et une spécialiste de la méthodologie; les membres ont divulgué tout conflit d’intérêts. Nous avons eu recours à un processus systématique, y compris l’approche GRADE (Grading of Recommendations Assessment, Development and Evaluation) pour formuler les lignes directrices. Les données ont été générées par une revue systématique d’études portant sur la déprescription des BZRA contre l’insomnie, de même que par une revue des revues sur les torts liés à la poursuite du traitement par BZRA et des synthèses narratives sur les préférences des patients et les répercussions sur les ressources. Ces données et le score GRADE de qualité des données ont servi à formuler les recommandations. L’équipe a peaufiné le texte sur le contenu et les recommandations des lignes directrices par consensus et a synthétisé les considérations cliniques afin de répondre aux questions des cliniciens de première ligne. Une version préliminaire des lignes directrices a été révisée par les cliniciens et les intervenants. Recommandations Nous recommandons d’offrir la déprescription (réduction lente de la dose) des BZRA à tous les patients âgés (≥ 65 ans) sous un BZRA, sans égard à la durée de l’usage, et suggérons d’offrir la déprescription (réduction lente de la dose) �

42 CFR 84.125 - Particulate tests; canisters containing particulate filters; minimum requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... filters; minimum requirements. 84.125 Section 84.125 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF... RESPIRATORY PROTECTIVE DEVICES Gas Masks § 84.125 Particulate tests; canisters containing particulate filters; minimum requirements. Gas mask canisters containing filters for protection against particulates (e.g...

42 CFR 84.125 - Particulate tests; canisters containing particulate filters; minimum requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... filters; minimum requirements. 84.125 Section 84.125 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF... RESPIRATORY PROTECTIVE DEVICES Gas Masks § 84.125 Particulate tests; canisters containing particulate filters; minimum requirements. Gas mask canisters containing filters for protection against particulates (e.g...

42 CFR 84.125 - Particulate tests; canisters containing particulate filters; minimum requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... filters; minimum requirements. 84.125 Section 84.125 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF... RESPIRATORY PROTECTIVE DEVICES Gas Masks § 84.125 Particulate tests; canisters containing particulate filters; minimum requirements. Gas mask canisters containing filters for protection against particulates (e.g...

42 CFR 84.125 - Particulate tests; canisters containing particulate filters; minimum requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... filters; minimum requirements. 84.125 Section 84.125 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF... RESPIRATORY PROTECTIVE DEVICES Gas Masks § 84.125 Particulate tests; canisters containing particulate filters; minimum requirements. Gas mask canisters containing filters for protection against particulates (e.g...

42 CFR 84.125 - Particulate tests; canisters containing particulate filters; minimum requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... filters; minimum requirements. 84.125 Section 84.125 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF... RESPIRATORY PROTECTIVE DEVICES Gas Masks § 84.125 Particulate tests; canisters containing particulate filters; minimum requirements. Gas mask canisters containing filters for protection against particulates (e.g...

Microfluidic paper-based analytical device for particulate metals.

PubMed

Mentele, Mallory M; Cunningham, Josephine; Koehler, Kirsten; Volckens, John; Henry, Charles S

2012-05-15

A microfluidic paper-based analytical device (μPAD) fabricated by wax printing was designed to assess occupational exposure to metal-containing aerosols. This method employs rapid digestion of particulate metals using microliters of acid added directly to a punch taken from an air sampling filter. Punches were then placed on a μPAD, and digested metals were transported to detection reservoirs upon addition of water. These reservoirs contained reagents for colorimetric detection of Fe, Cu, and Ni. Dried buffer components were used to set the optimal pH in each detection reservoir, while precomplexation agents were deposited in the channels between the sample and detection zones to minimize interferences from competing metals. Metal concentrations were quantified from color intensity images using a scanner in conjunction with image processing software. Reproducible, log-linear calibration curves were generated for each metal, with method detection limits ranging from 1.0 to 1.5 μg for each metal (i.e., total mass present on the μPAD). Finally, a standard incineration ash sample was aerosolized, collected on filters, and analyzed for the three metals of interest. Analysis of this collected aerosol sample using a μPAD showed good correlation with known amounts of the metals present in the sample. This technology can provide rapid assessment of particulate metal concentrations at or below current regulatory limits and at dramatically reduced cost.

Optical backscatter probe for sensing particulate in a combustion gas stream

DOEpatents

Parks, James E; Partridge, William P

2013-05-28

A system for sensing particulate in a combustion gas stream is disclosed. The system transmits light into a combustion gas stream, and thereafter detects a portion of the transmitted light as scattered light in an amount corresponding to the amount of particulates in the emissions. Purge gas may be supplied adjacent the light supply and the detector to reduce particles in the emissions from coating or otherwise compromising the transmission of light into the emissions and recovery of scattered light from the emissions.

Magnetic properties and heavy metal contents of automobile emission particulates*

PubMed Central

Lu, Sheng-gao; Bai, Shi-qiang; Cai, Jing-bo; Xu, Chang

2005-01-01

Measurements of the magnetic properties and total contents of Cu, Cd, Pb and Fe in 30 automobile emission particulate samples indicated the presence of magnetic particles in them. The values of frequency dependent susceptibility (χ fd) showed the absence of superparamagnetic (SP) grains in the samples. The IRM20 mT (isothermal remanent magnetization at 20 mT) being linearly proportional to SIRM (saturation isothermal remanent magnetization) (R 2=0.901), suggested that ferrimagnetic minerals were responsible for the magnetic properties of automobile emission particulates. The average contents of Cu, Cd, Pb and Fe in automobile emission particulates were 95.83, 22.14, 30.58 and 34727.31 mg/kg, respectively. Significant positive correlations exist between the magnetic parameters and the contents of Pb, Cu and Fe. The magnetic parameters of automobile emission particulates reflecting concentration of magnetic particles increased linearly with increase of Pb and Cu content, showed that the magnetic measurement could be used as a preliminary index for detection of Pb and Cu pollution. PMID:16052705

Strategies facilitant les tests en pre-certification pour la robustesse a l'egard des radiations =

NASA Astrophysics Data System (ADS)

Souari, Anis

Les effets des radiations cosmiques sur l'electronique embarquee preoccupent depuis. quelques decennies les chercheurs interesses par la robustesse des circuits integres. Plusieurs. recherches ont ete menees dans cette direction, principalement pour les applications spatiales. ou l’environnement de leur deploiement est hostile. En effet, ces environnements sont denses. en termes de particules qui, lorsqu’elles interagissent avec les circuits integres, peuvent. mener a leur dysfonctionnement, voir meme a leur destruction. De plus, les effets des. radiations s’accentuent pour les nouvelles generations des circuits integres ou la diminution. de la taille des transistors et l’augmentation de la complexite de ces circuits augmentent la. probabilite d’apparition des anomalies et par consequence la croissance des besoins de test. L’expansion de l’electronique grand public (commercial off-the-shelf, COTS) et l’adoption. de ces composants pour des applications critiques comme les applications avioniques et. spatiales incitent egalement les chercheurs a doubler les efforts de verification de la fiabilite. de ces circuits. Les COTS, malgre leurs meilleures caracteristiques en comparaison avec les. circuits durcis tolerants aux radiations qui sont couteux et en retard en termes de technologie. utilisee, sont vulnerables aux radiations. Afin d’ameliorer la fiabilite de ces circuits, une evaluation de leur vulnerabilite dans les. differents niveaux d’abstraction du flot de conception est recommandee. Ceci aide les. concepteurs a prendre les mesures de mitigation necessaires sur le design au niveau. d’abstraction en question. Enfin, afin de satisfaire les exigences de tolerance aux pannes, des. tests tres couteux de certification, obtenus a l’aide de bombardement de particules (protons, neutrons, etc.), sont necessaires. Dans cette these, nous nous interessons principalement a definir une strategie de precertification

Vecteurs Singuliers des Theories des Champs Conformes Minimales

NASA Astrophysics Data System (ADS)

Benoit, Louis

En 1984 Belavin, Polyakov et Zamolodchikov revolutionnent la theorie des champs en explicitant une nouvelle gamme de theories, les theories quantiques des champs bidimensionnelles invariantes sous les transformations conformes. L'algebre des transformations conformes de l'espace-temps presente une caracteristique remarquable: en deux dimensions elle possede un nombre infini de generateurs. Cette propriete impose de telles conditions aux fonctions de correlations qu'il est possible de les evaluer sans aucune approximation. Les champs des theories conformes appartiennent a des representations de plus haut poids de l'algebre de Virasoro, une extension centrale de l'algebre conforme du plan. Ces representations sont etiquetees par h, le poids conforme de leur vecteur de plus haut poids, et par la charge centrale c, le facteur de l'extension centrale, commune a toutes les representations d'une meme theorie. Les theories conformes minimales sont constituees d'un nombre fini de representations. Parmi celles-ci se trouvent des theories unitaires dont les representation forment la serie discrete de l'algebre de Virasoro; leur poids h a la forme h_{p,q}(m)=[ (p(m+1) -qm)^2-1] (4m(m+1)), ou p,q et m sont des entiers positifs et p+q<= m+1. L'entier m parametrise la charge centrale: c(m)=1 -{6over m(m+1)} avec n>= 2. Ces representations possedent un sous-espace invariant engendre par deux sous-representations avec h_1=h_{p,q} + pq et h_2=h_{p,q} + (m-p)(m+1-q) dont chacun des vecteurs de plus haut poids portent le nom de vecteur singulier et sont notes respectivement |Psi _{p,q}> et |Psi_{m-p,m+1-q}>. . Les theories super-conformes sont une version super-symetrique des theories conformes. Leurs champs appartiennent a des representation de plus haut poids de l'algebre de Neveu-Schwarz, une des deux extensions super -symetriques de l'algebre de Virasoro. Les theories super -conformes minimales possedent la meme structure que les theories conformes minimales. Les representations

Kuwaiti oil fires—Particulate monitoring

NASA Astrophysics Data System (ADS)

Husain, Tahir; Amin, Mohamed B.

The total suspended particulate (TSP) matters using a high-volume sampler and inhalable particulate matters using PM-10 samplers were collected at various locations in the Eastern Province of Saudi Arabia during and after the Kuwaiti oil fires. The collected samples were analysed for toxic metals and oil hydrocarbon concentrations including some carcinogenic organic compounds in addition to gravimetric analysis. The concentration values of particulate matters were determined on a daily basis at Dhahran. Abqaiq, Rahima, Tanajib and Jubail locations. The analyses of the filters show a high concentration of the inhalable particulate at various locations, especially when north or northwest winds were blowing. It was found that the inhalable particulate concentration exceeded the Meteorology and Environmental Protection Administration (MEPA) permissible limit of 340 μg m- 3 at most of these locations during May-October 1991. A trend between the total suspended particulate and inhalable particulate measured concurrently at the same locations was observed and a regression equation was developed to correlate PM-10 data with the total suspended particulate data.

Etudes des Reactions de Transfert LITHIUM-7/LITHIUM -6

NASA Astrophysics Data System (ADS)

Baddou, Djafer

Les reactions de transfert de deux nucleons ^7Li/^6Li(^3He, rm p)^8Be/^9Be ont ete effectuees a partir d'um faisceau d'^3He initialement polarise et d'energie incidente egale a 4.58 MeV au centre de la cible. Le faisceau d'^3He est simplement ionise et il est accelere par l'accelerateur Van de Graaff de l'Universite Laval. Ce faisceau d' ^3He est de polarisation egale a 40% et il est obtenu a partir d'une source d'^3He a l'etat metastable. Nous avons decrit la reaction depuis la production et le transport du faisceau initial de l'^3 He jusqu'a la chambre de reaction. Par la suite, nous avons obtenu les distributions angulaires de la section efficace differentielle et du pouvoir d'analyse de ces reactions. Elles ont ete comparees a la theorie DWBA a l'approximation zero. La theorie a montre qu'il s'agit d'un transfert de deux particules independants (neutron, proton) pour le cas de la reaction ^7Li( ^3He,rm p)^9Be et d'un transfert de "cluster" deuteron pour le cas de la reaction ^6Li(^3He, rm p)^8Be. Notons que pour cette reaction l'instabilite du ^8Be ne nous permet pas d'avoir une diffusion elastique permettant la determination des parametres du modele optique entre ce noyau et la particule diffusee. Afin de contourner cette difficulte, nous supposons que le ^8 Be est un noyau compose de deux particules alpha et nous avons teste cette hypothese avec les reactions ^6Li(^3He, rm p)^8Be et ^7Li( ^3He,rm d)^8Be. Nous mentionnons a la fin que nous avons observe que l'etat fondamental de la reaction ^6Li( ^3He,rm p)^8Be et l'etat excite 2.43 MeV de la reaction ^7Li(^3He,rm p)^9Be sont des reactions directes alors que le premier etat excite (2.96 MeV) de la reaction ^6Li(^3He,rm p)^8Be et l'etat fondamental de la reaction ^7Li(^3He,rm p)^9Be peuvent etre domines par une reaction a noyau compose.

Monitoring of PM10 and PM2.5 around primary particulate anthropogenic emission sources

NASA Astrophysics Data System (ADS)

Querol, Xavier; Alastuey, Andrés; Rodriguez, Sergio; Plana, Felicià; Mantilla, Enrique; Ruiz, Carmen R.

Investigations on the monitoring of ambient air levels of atmospheric particulates were developed around a large source of primary anthropogenic particulate emissions: the industrial ceramic area in the province of Castelló (Eastern Spain). Although these primary particulate emissions have a coarse grain-size distribution, the atmospheric transport dominated by the breeze circulation accounts for a grain-size segregation, which results in ambient air particles occurring mainly in the 2.5-10 μm range. The chemical composition of the ceramic particulate emissions is very similar to the crustal end-member but the use of high Al, Ti and Fe as tracer elements as well as a peculiar grain-size distribution in the insoluble major phases allow us to identify the ceramic input in the bulk particulate matter. PM2.5 instead of PM10 monitoring may avoid the interference of crustal particles without a major reduction in the secondary anthropogenic load, with the exception of nitrate. However, a methodology based in PM2.5 measurement alone is not adequate for monitoring the impact of primary particulate emissions (such as ceramic emissions) on air quality, since the major ambient air particles derived from these emissions are mainly in the range of 2.5-10 μm. Consequently, in areas characterised by major secondary particulate emissions, PM2.5 monitoring should detect anthropogenic particulate pollutants without crustal particulate interference, whereas PM10 measurements should be used in areas with major primary anthropogenic particulate emissions.

Development of real-time and lateral flow strip reverse transcription recombinase polymerase Amplification assays for rapid detection of peste des petits ruminants virus.

PubMed

Yang, Yang; Qin, Xiaodong; Song, Yiming; Zhang, Wei; Hu, Gaowei; Dou, Yongxi; Li, Yanmin; Zhang, Zhidong

2017-02-07

Peste des petits ruminants (PPR) is an economically important, Office International des Epizooties (OIE) notifiable, transboundary viral disease of small ruminants such as sheep and goat. PPR virus (PPRV), a negative-sense single-stranded RNA virus, is the causal agent of PPR. Therefore, sensitive, specific and rapid diagnostic assay for the detection of PPRV are necessary to accurately and promptly diagnose suspected case of PPR. In this study, reverse transcription recombinase polymerase amplification assays using real-time fluorescent detection (real-time RT-RPA assay) and lateral flow strip detection (LFS RT-RPA assay) were developed targeting the N gene of PPRV. The sensitivity of the developed real-time RT-RPA assay was as low as 100 copies per reaction within 7 min at 40 °C with 95% reliability; while the sensitivity of the developed LFS RT-RPA assay was as low as 150 copies per reaction at 39 °C in less than 25 min. In both assays, there were no cross-reactions with sheep and goat pox viruses, foot-and-mouth disease virus and Orf virus. These features make RPA assay promising candidates either in field use or as a point of care diagnostic technique.

Label-free carbon particulates detection in bio (medical) settings (Conference Presentation)

NASA Astrophysics Data System (ADS)

Steuwe, Christian; Bové, Hannelore; vandeVen, Martin J.; Ameloot, Marcel; Roeffaers, Maarten B. J.

2017-02-01

The adverse health effects of particulate matter exposure are a generally accepted concern. Dramatic statistical figures suggest that fine dust is a main environmental risk in Europe and can be held accountable for hundreds of thousands of deaths per year [1]. Locating and tracking these nanometer sized particles, however, is not straight forward: In epidemiological and toxicology research only measurements based on labels [2] such as radionuclide markers have been applied. In this paper we present a direct, label-free optical contrast mechanism to detect carbon nanoparticles immersed in aqueous environments [3]. The virtue of this technique is its ability to perform in body fluids such as urine but also in cells and tissues. The mechanism is based on white light (WL) generation upon illumination with femtosecond pulsed near-infrared and is therefore non-incandescence related. We demonstrate the technique in various biological settings with dry and suspended carbon black particles (CB), a widely used model compound for soot [4]. Our approach allows for the unequivocal localization of CB alongside of common fluorophores and markers and can be performed on multiphoton laser-scanning microscopy platforms, a system commonly available in research laboratories. [1] European Environment Agency (2015). Press release. [2] Kong et al. Int. J. Mol. Sci. 2013, 14, (11), 22529-22543 [3] Bové and Steuwe et al. Nano letters, 2016, (16) , pages 3173-3178 [4] Arnal et al. Combust. Sci. Technol. 2012, 184, (7-8), 1191-1206.

Particulate Air Pollution: The Particulars

ERIC Educational Resources Information Center

Murphy, James E.

1973-01-01

Describes some of the causes and consequences of particulate air pollution. Outlines the experimental procedures for measuring the amount of particulate materials that settles from the air and for observing the nature of particulate air pollution. (JR)

Effet de la composition des materiaux composites sur la caracterisation et detection par ondes de Lamb

NASA Astrophysics Data System (ADS)

Ostiguy, Pierre-Claude

Les matériaux composites sont de plus en plus utilisés en aéronautique. Leurs excellentes propriétés mécaniques et leur faible poids leur procurent un avantage certain par rapport aux matériaux métalliques. Ceux-ci étant soumis à diverses conditions de chargement et environnementales, ils sont suceptibles de subir plusieurs types d'endommagements, compromettant leur intégrité. Des méthodes fiables d'inspection sont donc nécessaires pour évaluer leur intégrité. Néanmoins, peu d'approches non destructives, embarquées et efficaces sont présentement utilisées. Ce travail de recherche se penche sur l'étude de l'effet de la composition des matériaux composites sur la détection et la caractérisation par ondes guidées. L'objectif du projet est de développer une approche de caractérisation mécanique embarquée permettant d'améliorer la performance d'une approche d'imagerie par antenne piézoélectriques sur des structures composite et métalliques. La contribution de ce projet est de proposer une approche embarquée de caractérisation mécanique par ultrasons qui ne requiert pas une mesure sur une multitude d'échantillons et qui est non destructive. Ce mémoire par articles est divisé en quatre parties, dont les parties deux A quatre présentant les articles publiés et soumis. La première partie présente l'état des connaissances dans la matière nécessaires à l'acomplissement de ce projet de maîtrise. Les principaux sujets traités portent sur les matériaux composites, propagation d'ondes, la modélisation des ondes guidées, la caractérisation par ondes guidées et la surveillance embarquée des structures. La deuxième partie présente une étude de l'effet des propriétés mécaniques sur la performance de l'algorithme d'imagerie Excitelet. L'étude est faite sur une structure isotrope. Les résultats ont démontré que l'algorithme est sensible à l'exactitude des propriétés mécaniques utilisées dans le modèle. Cette

Detection of the kinematic Sunyaev–Zel'dovich effect with DES Year 1 and SPT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Soergel, B.; Flender, S.; Story, K. T.

Here, we detect the kinematic Sunyaev-Zel'dovich (kSZ) effect with a statistical significance ofmore » $$4.2 \\sigma$$ by combining a cluster catalogue derived from the first year data of the Dark Energy Survey (DES) with CMB temperature maps from the South Pole Telescope Sunyaev-Zel'dovich (SPT-SZ) Survey. This measurement is performed with a differential statistic that isolates the pairwise kSZ signal, providing the first detection of the large-scale, pairwise motion of clusters using redshifts derived from photometric data. By fitting the pairwise kSZ signal to a theoretical template we measure the average central optical depth of the cluster sample, $$\\bar{\\tau}_e = (3.75 \\pm 0.89)\\cdot 10^{-3}$$. We compare the extracted signal to realistic simulations and find good agreement with respect to the signal-to-noise, the constraint on $$\\bar{\\tau}_e$$, and the corresponding gas fraction. High-precision measurements of the pairwise kSZ signal with future data will be able to place constraints on the baryonic physics of galaxy clusters, and could be used to probe gravity on scales $$ \\gtrsim 100$$ Mpc.« less

Detection of the kinematic Sunyaev–Zel'dovich effect with DES Year 1 and SPT

DOE PAGES

Soergel, B.; Flender, S.; Story, K. T.; ...

2016-06-17

Here, we detect the kinematic Sunyaev-Zel'dovich (kSZ) effect with a statistical significance ofmore » $$4.2 \\sigma$$ by combining a cluster catalogue derived from the first year data of the Dark Energy Survey (DES) with CMB temperature maps from the South Pole Telescope Sunyaev-Zel'dovich (SPT-SZ) Survey. This measurement is performed with a differential statistic that isolates the pairwise kSZ signal, providing the first detection of the large-scale, pairwise motion of clusters using redshifts derived from photometric data. By fitting the pairwise kSZ signal to a theoretical template we measure the average central optical depth of the cluster sample, $$\\bar{\\tau}_e = (3.75 \\pm 0.89)\\cdot 10^{-3}$$. We compare the extracted signal to realistic simulations and find good agreement with respect to the signal-to-noise, the constraint on $$\\bar{\\tau}_e$$, and the corresponding gas fraction. High-precision measurements of the pairwise kSZ signal with future data will be able to place constraints on the baryonic physics of galaxy clusters, and could be used to probe gravity on scales $$ \\gtrsim 100$$ Mpc.« less

Pitch based foam with particulate

DOEpatents

Klett, James W.

2001-01-01

A thermally conductive, pitch based foam composite having a particulate content. The particulate alters the mechanical characteristics of the foam without severely degrading the foam thermal conductivity. The composite is formed by mixing the particulate with pitch prior to foaming.

Electrical diesel particulate filter (DPF) regeneration

DOEpatents

Gonze, Eugene V; Ament, Frank

2013-12-31

An exhaust system that processes exhaust generated by an engine includes a diesel particulate filter (DPF) that is disposed downstream of the engine and that filters particulates from the exhaust. An electrical heater is disposed upstream of the DPF and selectively heats the exhaust to initiate combustion of the particulates within the exhaust as it passes therethrough. Heat generated by combustion of the particulates induces combustion of particulates within the DPF.

Hydrocarbon-enhanced particulate filter regeneration via microwave ignition

DOEpatents

Gonze, Eugene V.; Brown, David B.

2010-02-02

A regeneration method for a particulate filter includes estimating a quantity of particulate matter trapped within the particulate filter, comparing the quantity of particulate matter to a predetermined quantity, heating at least a portion of the particulate filter to a combustion temperature of the particulate matter, and introducing hydrocarbon fuel to the particulate filter. The hydrocarbon fuel facilitates combustion of the particulate matter to regenerate the particulate filter.

Estimating labile particulate iron concentrations in coastal waters from remote sensing data

NASA Astrophysics Data System (ADS)

McGaraghan, Anna R.; Kudela, Raphael M.

2012-02-01

Owing to the difficulties inherent in measuring trace metals and the importance of iron as a limiting nutrient for biological systems, the ability to monitor particulate iron concentration remotely is desirable. This study examines the relationship between labile particulate iron, described here as weak acid leachable particulate iron or total dissolvable iron, and easily obtained bio-optical measurements. We develop a bio-optical proxy that can be used to estimate large-scale patterns of labile iron concentrations in surface waters, and we extend this by including other environmental variables in a multiple linear regression statistical model. By utilizing a ratio of optical backscatter and fluorescence obtained by satellite, we identify patterns in iron concentrations confirmed by traditional shipboard sampling. This basic relationship is improved with the addition of other environmental parameters in the statistical linear regression model. The optical proxy detects known temporal and spatial trends in average surface iron concentrations in Monterey Bay. The proxy is robust in that similar performance was obtained using two independent particulate iron data sets, but it exhibits weaker correlations than the full statistical model. This proxy will be a valuable tool for oceanographers seeking to monitor iron concentrations in coastal regions and allows for better understanding of the variability of labile particulate iron in surface waters to complement direct measurement of leachable particulate or total dissolvable iron.

Electrically heated particulate filter restart strategy

DOEpatents

Gonze, Eugene V [Pinckney, MI; Ament, Frank [Troy, MI

2011-07-12

A control system that controls regeneration of a particulate filter is provided. The system generally includes a propagation module that estimates a propagation status of combustion of particulate matter in the particulate filter. A regeneration module controls current to the particulate filter to re-initiate regeneration based on the propagation status.

30 CFR 57.5075 - Diesel particulate records.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Diesel particulate records. 57.5075 Section 57..., Radiation, Physical Agents, and Diesel Particulate Matter Diesel Particulate Matter-Underground Only § 57.5075 Diesel particulate records. (a) The table entitled “Diesel Particulate Matter Recordkeeping...

30 CFR 57.5075 - Diesel particulate records.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Diesel particulate records. 57.5075 Section 57..., Radiation, Physical Agents, and Diesel Particulate Matter Diesel Particulate Matter-Underground Only § 57.5075 Diesel particulate records. (a) The table entitled “Diesel Particulate Matter Recordkeeping...

Particulate-Phase Carbonyls: Laboratory and Pacific 2001 Field Measurements

NASA Astrophysics Data System (ADS)

Liggio, J.; McLaren, R.

2002-12-01

Atmospheric aldehydes and ketones are important constituents of the gas phase. They are emitted from athropogenic and biogenic sources directly, but are also formed as secondary oxidation products of a variety of saturated and unsaturated hydrocarbons. Although their gas phase occurrence and chemistry is well known, the presence of these compounds in the particulate phase is not completely understood. A method has been developed to measure particulate phase carbonyls. Analysis was performed by a simultaneous extraction and derivatization of carbonyls by 2,4-dinitrophenylhydrazine. The subsequent derivatives are pre-concentrated and injected onto an HPLC and detected by UV absorption. Laboratory studies of the extraction kinetics, suggest that partitioning of even highly volatile carbonyls may be possible. Also, experiments performed to determine the extent of positive artifacts on Teflon coated filters, indicate that measurements of these volatile carbonyls are likely not a result of gas-phase adsorption to the filter. These studies also indicate that sampling on quartz fiber filters may introduce significantly more uncertainty with respect to positive artifacts. The analytical method was used to analyze filters sampled during the Pacific 2001 field campaign. Particulate samples were collected on Teflon coated glass-fiber filters. Samples were collected at an urban site (Slocan Park,Vancouver), a rural site (Langley) and an elevated rural mountain site (Eagle Ridge, Sumas). Preliminary results show several carbonyls present in aerosols, at pg/m3 to ng/m3 levels. Detected carbonyls of possible anthropogenic origin include formaldehyde, acetaldehyde, acetone, propanal, glyoxal and methylglyoxal. Detected carbonyls of biogenic origin include pinonaldehyde and nopinone, known oxidation products of the biogenically emitted a-pinene and b-pinene. Possible mechanisms for carbonyl partitioning and implications for their contribution to aerosols in the Lower Fraser Valley

What We Did Last Summer: Depicting DES Data to Enhance Simulation Utility and Use

NASA Technical Reports Server (NTRS)

Elfrey, Priscilla; Conroy, Mike; Lagares, Jose G.; Mann, David; Fahmi, Mona

2009-01-01

At Kennedy Space Center (KSC), an important use of Discrete Event Simulation (DES) addresses ground operations .of missions to space. DES allows managers, scientists and engineers to assess the number of missions KSC can complete on a given schedule within different facilities, the effects of various configurations of resources and detect possible problems or unwanted situations. For fifteen years, DES has supported KSC efficiency, cost savings and improved safety and performance. The dense and abstract DES data, however, proves difficult to comprehend and, NASA managers realized, is subject to misinterpretation, misunderstanding and even, misuse. In summer 2008, KSC developed and implemented a NASA Exploration Systems Mission Directorate (ESMD) project based on the premise that visualization could enhance NASA's understanding and use of DES.

Hyperspectral imaging applied to complex particulate solids systems

NASA Astrophysics Data System (ADS)

Bonifazi, Giuseppe; Serranti, Silvia

2008-04-01

HyperSpectral Imaging (HSI) is based on the utilization of an integrated hardware and software (HW&SW) platform embedding conventional imaging and spectroscopy to attain both spatial and spectral information from an object. Although HSI was originally developed for remote sensing, it has recently emerged as a powerful process analytical tool, for non-destructive analysis, in many research and industrial sectors. The possibility to apply on-line HSI based techniques in order to identify and quantify specific particulate solid systems characteristics is presented and critically evaluated. The originally developed HSI based logics can be profitably applied in order to develop fast, reliable and lowcost strategies for: i) quality control of particulate products that must comply with specific chemical, physical and biological constraints, ii) performance evaluation of manufacturing strategies related to processing chains and/or realtime tuning of operative variables and iii) classification-sorting actions addressed to recognize and separate different particulate solid products. Case studies, related to recent advances in the application of HSI to different industrial sectors, as agriculture, food, pharmaceuticals, solid waste handling and recycling, etc. and addressed to specific goals as contaminant detection, defect identification, constituent analysis and quality evaluation are described, according to authors' originally developed application.

Fiabilité des structures mécaniques adaptatives: effet de la panne des actionneurs ou des capteurs sur la stabilité

NASA Astrophysics Data System (ADS)

Fall, H.; Charon, W.; Kouta, R.

2002-12-01

Ces dernières décennies, des activités significatives dans le monde étaient dirigées autour du contrôle actif. Le but de ces recherches était essentiellement d'améliorer les performances, la fiabilité et la sécurité des systèmes. Notamment dans le cas des structures soumises à des vibrations aléatoires. D'importants travaux ont été consacré à l'utilisation des “matériaux intelligents” comme capteurs et actionneurs. Cette article propose l'analyse de la fiabilité des systèmes mécaniques en étudiant les pannes des actionneurs ou des capteurs. L'effet de ces pannes sur la stabilité et la performance du système y est démontré. Les méthodologies de conception y sont rappelées. Des exemples numériques sont fournis à travers le contrôle d'un panneau sous chargement dynamique pour illustrer la méthode proposée.

Characteristics and source appointment of atmospheric particulate mercury over East China Sea: Implication on the deposition of atmospheric particulate mercury in marine environment.

PubMed

Duan, Lian; Cheng, Na; Xiu, Guangli; Wang, Fujiang; Chen, Ying

2017-05-01

Total Suspended Particulate (TSP) samples were collected at Huaniao Island in northern East China Sea (ECS) from March 2012 to January 2013. Chemical analysis were conducted to measure the concentration of total particulate mercury (TPM) and speciated particulate mercury including HCl-soluble particulate mercury (HPM), elemental particulate mercury (EPM) and residual particulate mercury (RPM). The bromine (Br) and iodine (I) on particles were also detected. The mean concentration of TPM during the study period was 0.23 ± 0.15 ng m -3 , while the obviously seasonal variation was found that the concentrations of TPM in spring, summer, fall and winter were 0.34 ± 0.20 ng m -3 , 0.15 ± 0.03 ng m -3 , 0.15 ± 0.05 ng m -3 and 0.27 ± 0.26 ng m -3 , respectively. The statistically strong correlation of bromine and iodine to HPM was only found in spring with r = 0.81 and 0.77 (p < 0.01), respectively. While the strongest correlations between EPM and bromine and iodine were found in winter with r = 0.92 (Br) and 0.96 (I) (p < 0.01), respectively. The clustered 72-h backward trajectories of different seasons and the whole sampling period were categorized into 4 groups. In spring, the clusters passed a long distance across the East China Sea and brought about low concentration of mercury due to the deposition of mercury over the sea. The cluster of air mass across the sea had low concentration of HPM in winter, which suggested that the oxidation of mercury in winter might be related to other oxidants. During the whole sampling period, the air mass from the north of China contributed to the higher concentration of TPM in Huaniao Island. Copyright © 2016 Elsevier Ltd. All rights reserved.

Modelisation 0D/1D des emissions de particules de suie dans les turbines a gaz aeronautiques

NASA Astrophysics Data System (ADS)

Bisson, Jeremie

Because of more stringent regulations of aircraft particle emissions as well as strong uncertainties about their formation and their effects on the atmosphere, a better understanding of particle microphysical mechanisms and their interactions with the engine components is required. This thesis focuses on the development of a 0D/1D combustion model with soot production in an aeronautical gas turbine. A major objective of this study is to assess the quality of soot particle emission predictions for different flight configurations. The model should eventually allow performing parametric studies on current or future engines with a minimal computation time. The model represents the combustor as well as turbines and nozzle with a chemical reactor network (CRN) that is coupled with a detailed combustion chemistry for kerosene (Jet A-1) and a soot particle dynamics model using the method of moments. The CRN was applied to the CFM56-2C1 engine during flight configurations of the LTO cycle (Landing-Take-Off) as in the APEX-1 study on aircraft particle emissions. The model was mainly validated on gas turbine thermodynamic data and pollutant concentrations (H2O, COX, NOx, SOX) which were measured in the same study. Once the first validation completed, the model was subsequently used for the computation of mass and number-based emissions indices of the soot particulate population and average diameter. Overall, the model is representative of the thermodynamic conditions and succeeds in predicting the emissions of major pollutants, particularly at high power. Concerning soot particulate emissions, the model's ability to predict simultaneously the emission indices as well as mean diameter has been partially validated. Indeed, the mass emission indices have remained higher than experimental results particularly at high power. These differences on particulate emission index may be the result of uncertainties on thermodynamic parameters of the CRN and mass air flow distribution in

Escherichia coli attachment to model particulates: The effects of bacterial cell characteristics and particulate properties.

PubMed

Liang, Xiao; Liao, Chunyu; Soupir, Michelle L; Jarboe, Laura R; Thompson, Michael L; Dixon, Philip M

2017-01-01

E. coli bacteria move in streams freely in a planktonic state or attached to suspended particulates. Attachment is a dynamic process, and the fraction of attached microorganisms is thought to be affected by both bacterial characteristics and particulate properties. In this study, we investigated how the properties of cell surfaces and stream particulates influence attachment. Attachment assays were conducted for 77 E. coli strains and three model particulates (ferrihydrite, Ca-montmorillonite, or corn stover) under environmentally relevant conditions. Surface area, particle size distribution, and total carbon content were determined for each type of particulate. Among the three particulates, attachment fractions to corn stover were significantly larger than the attachments to 2-line ferrihydrite (p-value = 0.0036) and Ca-montmorillonite (p-value = 0.022). Furthermore, attachment to Ca-montmorillonite and corn stover was successfully modeled by a Generalized Additive Model (GAM) using cell characteristics as predictor variables. The natural logarithm of the net charge on the bacterial surface had a significant, positive, and linear impact on the attachment of E. coli bacteria to Ca-montmorillonite (p-value = 0.013), but it did not significantly impact the attachment to corn stover (p-value = 0.36). The large diversities in cell characteristics among 77 E. coli strains, particulate properties, and attachment fractions clearly demonstrated the inadequacy of using a static parameter or linear coefficient to predict the attachment behavior of E. coli in stream water quality models.

Developpement des betons semi autoplacants a rheologie adaptee pour des infrastructures

NASA Astrophysics Data System (ADS)

Sotomayor Cruz, Cristian Daniel

Au cours des dernières décennies, les infrastructures canadiennes et québécoises comportent plusieurs structures en béton armé présentant des problèmes de durabilité dus aux conditions climatiques sévères, à la mauvaise conception des structures, à la qualité des matériaux, aux types des bétons choisis, aux systèmes de construction ou à l'existence d'événements incontrôlables. En ce qui concerne le choix du béton pour la construction des infrastructures, une vaste gamme de béton divisée en deux principaux types peut être utilisée: le béton conventionnel vibré (BCV) et le béton autoplaçant (BAP). Dans le cas d'un BCV, la consolidation inadéquate par vibration a été un problème récurrent, occasionnant des dommages structuraux. Ceci a conduit à une réduction de la durabilité et à une augmentation du coût d'entretien et de réparation des infrastructures. Rien que l'utilisation d'un BAP a des avantages tels que l'élimination de la vibration, la réduction des coûts de main d'oeuvre et l'amélioration de la qualité des structures, néanmoins, le coût initial d'un BAP par rapport à un BCV ne permet pas encore de généraliser son utilisation dans l'industrie de la construction. Ce mémoire présente la conception d'une nouvelle gamme de béton semi-autoplaçant pour la construction des infrastructures (BSAP-I) exigeant une vibration minimale. Il s'agit de trouver un équilibre optimal entre la rhéologie et le coût initial du nouveau béton pour conférer une bonne performance structurale et économique aux structures. Le programme expérimental établi a premièrement permis d'évaluer la faisabilité d'utilisation des BSAP-I pour la mise en place des piliers d'une infrastructure de pont à Sherbrooke. En plus, l'utilisation d'un plan d'expériences a permis l'évaluation de trois paramètres de formulation sur les propriétés des mélanges de BSAP-I à l'état frais et durci. Finalement, l'évaluation de la performance des

Feasibility of the detection of trace elements in particulate matter using online High-Resolution Aerosol Mass Spectrometry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Salcedo, D.; Laskin, Alexander; Shutthanandan, V.

The feasibility of using an online thermal-desorption electron-ionization high-resolution aerosol mass spectrometer (AMS) for the detection of particulate trace elements was investigated analyzing data from Mexico City obtained during the MILAGRO 2006 field campaign, where relatively high concentrations of trace elements have been reported. This potential application is of interest due to the real-time data provided by the AMS, its high sensitivity and time resolution, and the widespread availability and use of this instrument. High resolution mass spectral analysis, isotopic ratios, and ratios of different ions containing the same elements are used to constrain the chemical identity of the measuredmore » ions. The detection of Cu, Zn, As, Se, Sn, and Sb is reported. There was no convincing evidence for the detection of other trace elements commonly reported in PM. The elements detected tend to be those with lower melting and boiling points, as expected given the use of a vaporizer at 600oC in this instrument. Operation of the AMS vaporizer at higher temperatures is likely to improve trace element detection. The detection limit is estimated at approximately 0.3 ng m-3 for 5-min of data averaging. Concentration time series obtained from the AMS data were compared to concentration records determined from offline analysis of particle samples from the same times and locations by ICP (PM2.5) and PIXE (PM1.1 and PM0.3). The degree of correlation and agreement between the three instruments (AMS, ICP, and PIXE) varied depending on the element. The AMS shows promise for real-time detection of some trace elements, although additional work including laboratory calibrations with different chemical forms of these elements are needed to further develop this technique and to understand the differences with the ambient data from the other techniques. The trace elements peaked in the morning as expected for primary sources, and the many detected plumes suggest the presence of

Paternité des articles et intérêts concurrents : une analyse des recommandations aux auteurs des journaux traitant de pratique pharmaceutique

PubMed Central

Courbon, Ève; Tanguay, Cynthia; Lebel, Denis; Bussières, Jean-François

2014-01-01

RÉSUMÉ Contexte : La présence d’auteurs honorifiques et fantômes ainsi que les intérêts concurrents représentent des difficultés bien documentées, liées à la publication d’articles scientifiques. Il existe des lignes directrices encadrant la rédaction et la publication de manuscrits scientifiques, notamment celles de l’International Committee of Medical Journal Editors (ICMJE). Objectifs : L’objectif principal de cette étude descriptive et transversale visait à recenser les instructions portant sur la paternité des articles et les intérêts concurrents provenant des recommandations aux auteurs des journaux traitant de pratique pharmaceutique. L’objectif secondaire visait à déterminer des mesures correctrices pour une paternité des articles plus transparente. Méthode : La recherche a débuté par l’identification des journaux traitant de pratique pharmaceutique. La consultation des instructions aux auteurs des journaux a permis ensuite de recenser les recommandations destinées à éviter les problèmes de paternité des articles et d’intérêts concurrents. Finalement, les membres de l’équipe de recherche se sont consultés afin de définir des mesures correctrices possibles à l’intention des chercheurs. Résultats : Des 232 journaux traitant de pharmacie, 33 ont été définis comme traitant de pratique pharmaceutique. Un total de 24 (73 %) journaux mentionnaient suivre la politique de l’ICMJE, 14 (42 %) demandaient aux auteurs de remplir un formulaire de déclaration d’intérêts concurrents au moment de la soumission de l’article, 17 (52 %) présentaient une définition de la qualité d’auteur et 5 (15 %) demandaient de détailler les contributions de chaque auteur. Une grille de 40 critères a été élaborée pour définir l’attribution du statut d’auteur. Conclusion : Moins de la moitié des journaux demandait aux auteurs de transmettre un formulaire de déclaration des intérêts concurrents au moment de la

Particulate residue separators for harvesting devices

DOEpatents

Hoskinson, Reed L.; Kenney, Kevin L.; Wright, Christopher T.; Hess, John R.

2010-06-29

A particulate residue separator and a method for separating a particulate residue stream may include a plenum borne by a harvesting device, and have a first, intake end and a second, exhaust end; first and second particulate residue air streams which are formed by the harvesting device and which travel, at least in part, along the plenum and in a direction of the second, exhaust end; and a baffle assembly which is located in partially occluding relation relative to the plenum, and which substantially separates the first and second particulate residue air streams.

Caracterisation des melanges developpes pour le moulage basse pression des poudres metalliques (LPIM) =

NASA Astrophysics Data System (ADS)

Fareh, Fouad

Le moulage par injection basse pression des poudres metalliques est une technique de fabrication qui permet de fabriquer des pieces possedant la complexite des pieces coulees mais avec les proprietes mecaniques des pieces corroyees. Cependant, l'optimisation des etapes de deliantage et de frittage a ete jusqu'a maintenant effectuee a l'aide de melange pour lesquels la moulabilite optimale n'a pas encore ete demontree. Ainsi, la comprehension des proprietes rheologiques et de la segregation des melanges est tres limitee et cela presente le point faible du processus de LPIM. L'objectif de ce projet de recherche etait de caracteriser l'influence des liants sur le comportement rheologique des melanges en mesurant la viscosite et la segregation des melanges faible viscosite utilises dans le procede LPIM. Afin d'atteindre cet objectif, des essais rheologiques et thermogravimetriques ont ete conduits sur 12 melanges. Ces melanges ont ete prepares a base de poudre d'Inconel 718 de forme spherique (chargement solide constant a 60%) et de cires, d'agents surfactants ou epaississants. Les essais rheologiques ont ete utilises entre autre pour calculer l'indice d'injectabilite ?STV des melanges, tandis que les essais thermogravimetriques ont permis d'evaluer precisement la segregation des poudres dans les melanges. Il a ete demontre que les trois (3) melanges contenant de la cire de paraffine et de l'acide stearique presentent des indices alpha STV plus eleves qui sont avantageux pour le moulage par injection des poudres metalliques (MIM), mais segregent beaucoup trop pour que la piece fabriquee produise de bonnes caracteristiques mecaniques. A l'oppose, le melange contenant de la cire de paraffine et de l'ethylene-vinyle acetate ainsi que le melange contenant seulement de la cire de carnauba segregent peu voire pas du tout, mais possedent de tres faibles indices alphaSTV : ils sont donc difficilement injectables. Le meilleur compromis semble donc etre les melanges contenant de

HIGH VOLUME INJECTION FOR GCMS ANALYSIS OF PARTICULATE ORGANIC SPECIES IN AMBIENT AIR

EPA Science Inventory

Detection of organic species in ambient particulate matter typically requires large air sample volumes, frequently achieved by grouping samples into monthly composites. Decreasing the volume of air sample required would allow shorter collection times and more convenient sample c...

La participation des enfants et des adolescents à la boxe

PubMed Central

Purcell, Laura K; LeBlanc, Claire MA

2012-01-01

RÉSUMÉ Des milliers de garçons et de filles de moins de 19 ans font de la boxe en Amérique du Nord. Même si la boxe comporte des avantages pour ceux qui y participent, y compris l’exercice, l’autodiscipline et la confiance en soi, le sport lui-même favorise et récompense des coups délibérés à la tête et au visage. Les personnes qui font de la boxe risquent de subir des blessures à la tête, au visage et au cou, y compris des traumatismes neurologiques chroniques et même fatals. Les commotions cérébrales sont l’une des principales blessures causées par la boxe. En raison du risque de blessures crâniennes et faciales, la Société canadienne de pédiatrie et l’American Academy of Pediatrics s’opposent vigoureusement à la boxe comme activité sportive pour les enfants et les adolescents. Ces organismes recommandent que les médecins s’élèvent contre la boxe auprès des jeunes et les encouragent à participer à d’autres activités dans lesquelles les coups intentionnels à la tête ne constituent pas un élément essentiel du sport.

CMB lensing tomography with the DES Science Verification galaxies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Giannantonio, T.

We measure the cross-correlation between the galaxy density in the Dark Energy Survey (DES) Science Verification data and the lensing of the cosmic microwave background (CMB) as reconstructed with the Planck satellite and the South Pole Telescope (SPT). When using the DES main galaxy sample over the full redshift range 0.2 < z phot < 1.2, a cross-correlation signal is detected at 6σ and 4σ with SPT and Planck respectively. We then divide the DES galaxies into five photometric redshift bins, finding significant (>2σ) detections in all bins. Comparing to the fiducial Planck cosmology, we find the redshift evolution ofmore » the signal matches expectations, although the amplitude is consistently lower than predicted across redshift bins. We test for possible systematics that could affect our result and find no evidence for significant contamination. Finally, we demonstrate how these measurements can be used to constrain the growth of structure across cosmic time. We find the data are fit by a model in which the amplitude of structure in the z < 1.2 universe is 0.73 ± 0.16 times as large as predicted in the LCDM Planck cosmology, a 1.7σ deviation.« less

CMB lensing tomography with the DES Science Verification galaxies

DOE PAGES

Giannantonio, T.

2016-01-07

We measure the cross-correlation between the galaxy density in the Dark Energy Survey (DES) Science Verification data and the lensing of the cosmic microwave background (CMB) as reconstructed with the Planck satellite and the South Pole Telescope (SPT). When using the DES main galaxy sample over the full redshift range 0.2 < z phot < 1.2, a cross-correlation signal is detected at 6σ and 4σ with SPT and Planck respectively. We then divide the DES galaxies into five photometric redshift bins, finding significant (>2σ) detections in all bins. Comparing to the fiducial Planck cosmology, we find the redshift evolution ofmore » the signal matches expectations, although the amplitude is consistently lower than predicted across redshift bins. We test for possible systematics that could affect our result and find no evidence for significant contamination. Finally, we demonstrate how these measurements can be used to constrain the growth of structure across cosmic time. We find the data are fit by a model in which the amplitude of structure in the z < 1.2 universe is 0.73 ± 0.16 times as large as predicted in the LCDM Planck cosmology, a 1.7σ deviation.« less

Membrane fluidization by alcohols inhibits DesK-DesR signalling in Bacillus subtilis.

PubMed

Vaňousová, Kateřina; Beranová, Jana; Fišer, Radovan; Jemioła-Rzemińska, Malgorzata; Matyska Lišková, Petra; Cybulski, Larisa; Strzałka, Kazimierz; Konopásek, Ivo

2018-03-01

After cold shock, the Bacillus subtilis desaturase Des introduces double bonds into the fatty acids of existing membrane phospholipids. The synthesis of Des is regulated exclusively by the two-component system DesK/DesR; DesK serves as a sensor of the state of the membrane and triggers Des synthesis after a decrease in membrane fluidity. The aim of our work is to investigate the biophysical changes in the membrane that are able to affect the DesK signalling state. Using linear alcohols (ethanol, propanol, butanol, hexanol, octanol) and benzyl alcohol, we were able to suppress Des synthesis after a temperature downshift. The changes in the biophysical properties of the membrane caused by alcohol addition were followed using membrane fluorescent probes and differential scanning calorimetry. We found that the membrane fluidization induced by alcohols was reflected in an increased hydration at the lipid-water interface. This is associated with a decrease in DesK activity. The addition of alcohol mimics a temperature increase, which can be measured isothermically by fluorescence anisotropy. The effect of alcohols on the membrane periphery is in line with the concept of the mechanism by which two hydrophilic motifs located at opposite ends of the transmembrane region of DesK, which work as a molecular caliper, sense temperature-dependent variations in membrane properties. Copyright © 2017 Elsevier B.V. All rights reserved.

Polarimetric discrimination of atmospheric particulate matter

NASA Astrophysics Data System (ADS)

Raman, Prashant; Fuller, Kirk; Gregory, Don

2012-06-01

A polarimeter capable of measuring the complete Mueller matrix of highly scattering samples in transmission and reflection from 300 to 1100 nm has been constructed and tested. Exploratory research has been conducted which may lead to the standoff detection of bio-aerosols in the atmosphere. The polarization properties of bsubtilis (surrogate for anthrax spore) have been compared to ambient particulate matter species such as pollen, dust and soot (all sampled onto microscope slides) and differentiating features have been identified. The application of this technique for the discrimination of bio-aerosol from background clutter has been demonstrated.

Basics of Sterile Compounding: Particulate Matter.

PubMed

Akers, Michael J

2017-01-01

This article focuses on the requirements for particulate matter in sterile products. Topics include particles and quality, particulate matter standards (large- and small-volume injectables), development of the small-volume injectable test, electronic (light obscuration) and microscope testing, and special requirements for particulate matter in biopharmaceutical preparations. Copyright© by International Journal of Pharmaceutical Compounding, Inc.

Etude du processus de changement vecu par des familles ayant decide d'adopter volontairement des comportements d'attenuation des changements climatiques

NASA Astrophysics Data System (ADS)

Leger, Michel T.

Les activites humaines energivores telles l'utilisation intensive de l'automobile, la surconsommation de biens et l'usage excessif d'electricite contribuent aux changements climatiques et autres problemes environnementaux. Bien que plusieurs recherches rapportent que l'etre humain est de plus en plus conscient de ses impacts sur le climat de la planete, ces memes recherches indiquent qu'en general, les gens continuent a se comporter de facon non ecologique. Que ce soit a l'ecole ou dans la communaute, plusieurs chercheurs en education relative a l'environnement estiment qu'une personne bien intentionnee est capable d'adopter des comportements plus respectueux de l'environnement. Le but de cette these etait de comprendre le processus d'integration de comportements d'attenuation des changements climatiques dans des familles. A cette fin, nous nous sommes fixe deux objectifs : 1) decrire les competences et les procedes qui favorisent l'adoption de comportements d'attenuation des changements climatiques dans des familles et 2) decrire les facteurs et les dynamiques familiales qui facilitent et limitent l'adoption de comportements d'attenuation des changements climatiques dans des familles. Des familles ont ete invitees a essayer des comportements personnels et collectifs d'attenuation des changements climatiques de sorte a integrer des modes de vie plus ecologiques. Sur une periode de huit mois, nous avons suivi leur experience de changement afin de mieux comprendre comment se produit le processus de changement dans des familles qui decident volontairement d'adopter des comportements d'attenuation des changements climatiques. Apres leur avoir fourni quelques connaissances de base sur les changements climatiques, nous avons observe le vecu de changement des familles durant huit mois d'essais a l'aide de journaux reflexifs, d'entretiens d'explicitation et du journal du chercheur. La these comporte trois articles scientifiques. Dans le premier article, nous presentons une

Methods of separating particulate residue streams

DOEpatents

Hoskinson, Reed L [Rigby, ID; Kenney, Kevin L [Idaho Falls, ID; Wright, Christopher T [Idaho Falls, ID; Hess, J Richard [Idaho Falls, ID

2011-04-05

A particulate residue separator and a method for separating a particulate residue stream may include an air plenum borne by a harvesting device, and have a first, intake end and a second, exhaust end; first and second particulate residue air streams that are formed by the harvesting device and that travel, at least in part, along the air plenum and in a direction of the second, exhaust end; and a baffle assembly that is located in partially occluding relation relative to the air plenum and that substantially separates the first and second particulate residue air streams.

Development of recombinase polymerase amplification assays for the rapid detection of peste des petits ruminants virus.

PubMed

Zhang, Yongning; Wang, Jianchang; Zhang, Zhou; Mei, Lin; Wang, Jinfeng; Wu, Shaoqiang; Lin, Xiangmei

2018-04-01

Peste des petits ruminants (PPR) is a severe infectious disease of small ruminants caused by PPR virus (PPRV). Rapid and sensitive detection of PPRV is critical for controlling PPR. This report describes the development and evaluation of a conventional reverse transcription recombinase polymerase amplification (RT-RPA) assay and a real-time RT-RPA assay, targeting the PPRV N gene. Sensitivity analysis revealed that the conventional RT-RPA assay could detect 852 copies of standard PPRV RNA per reaction at 95% probability within 20 min at 41 °C, and the real-time RT-RPA assay could detect 103 copies of RNA molecules per reaction at 95% probability. Specificity analysis showed that both assays have no cross-reactivity with nucleic acid templates prepared from other selected viruses or common pathogens. Clinical evaluation using 162 ovine and hircine serum and nasal swab samples showed that the performance of both the real-time RT-RPA assay and the conventional RT-RPA assay were comparable to that of real-time RT-PCR. The overall agreements between real-time RT-PCR and real-time RT-RPA, and conventional RT-RPA were 99.4% (161/162) and 98.8% (160/162), respectively. The R 2 value of real-time RT-RPA and real-time RT-PCR was 0.900 by linear regression analysis. Our results suggest that both RT-RPA assays have a potential application in the rapid, sensitive and specific detection of PPRV. Copyright © 2018 Elsevier B.V. All rights reserved.

Personal exposure assessment to particulate metals using a paper-based analytical device

NASA Astrophysics Data System (ADS)

Cate, David; Volckens, John; Henry, Charles

2013-03-01

The development of a paper-based analytical device (PAD) for assessing personal exposure to particulate metals will be presented. Human exposure to metal aerosols, such as those that occur in the mining, construction, and manufacturing industries, has a significant impact on the health of our workforce, costing an estimated $10B in the U.S and causing approximately 425,000 premature deaths world-wide each year. Occupational exposure to particulate metals affects millions of individuals in manufacturing, construction (welding, cutting, blasting), and transportation (combustion, utility maintenance, and repair services) industries. Despite these effects, individual workers are rarely assessed for their exposure to particulate metals, due mainly to the high cost and effort associated with personal exposure measurement. Current exposure assessment methods for particulate metals call for an 8-hour filter sample, after which time, the filter sample is transported to a laboratory and analyzed by inductively-coupled plasma (ICP). The time from sample collection to reporting is typically weeks and costs several hundred dollars per sample. To exacerbate the issue, method detection limits suffer because of sample dilution during digestion. The lack of sensitivity hampers task-based exposure assessment, for which sampling times may be tens of minutes. To address these problems, and as a first step towards using microfluidics for personal exposure assessment, we have developed PADs for measurement of Pb, Cd, Cr, Fe, Ni, and Cu in aerosolized particulate matter.

Fire Detection Organizing Questions

NASA Technical Reports Server (NTRS)

2004-01-01

Verified models of fire precursor transport in low and partial gravity: a. Development of models for large-scale transport in reduced gravity. b. Validated CFD simulations of transport of fire precursors. c. Evaluation of the effect of scale on transport and reduced gravity fires. Advanced fire detection system for gaseous and particulate pre-fire and fire signaturesa: a. Quantification of pre-fire pyrolysis products in microgravity. b. Suite of gas and particulate sensors. c. Reduced gravity evaluation of candidate detector technologies. d. Reduced gravity verification of advanced fire detection system. e. Validated database of fire and pre-fire signatures in low and partial gravity.

Characterization of chemical and particulate emissions from aircraft engines

NASA Astrophysics Data System (ADS)

Agrawal, Harshit; Sawant, Aniket A.; Jansen, Karel; Wayne Miller, J.; Cocker, David R.

2008-06-01

This paper presents a series of measurements from four on-wing, commercial aircraft engines, including two newer CFM56-7 engines and two earlier CFM56-3 engines. Samples were collected from each engine using a probe positioned behind the exhaust nozzle of the aircraft, chocked on a concrete testing pad. The emission factors for particulate matter mass, elemental and organic carbon, carbonyls, polycyclic aromatic hydrocarbons, n-alkanes, dioxins, metals and ions are reported for four different engine power setting modes. The emissions indices of particulate matter, elemental and organic carbon are highly power dependent for these engines. Particulate matter emission indices (g kg-1 fuel) are found to increase from 1.1E-02 to 2.05E-01 with increase in power from idle to 85%. The elemental carbon to organic carbon varies from 0.5 to 3.8 with change in power from idle to 85%. The carbonyl emissions are dominated by formaldehyde. The emission index of formaldehyde ranges from 2.3E-01 to 4.8E-01 g kg-1 fuel. The distribution of metals depends on the difference in the various engines. The dioxin emissions from the aircraft engines are observed to be below detection limit.

Des ballons pour demain

NASA Astrophysics Data System (ADS)

Régipa, R.

A partir d'une théorie sur la détermination des formes et des contraintes globales d'un ballon de révolution, ou s'en rapprochant, une nouvelle famille de ballons a été définie. Les ballons actuels, dits de ``forme naturelle'', sont calculés en général pour une tension circonférencielle nulle. Ainsi, pour une mission donnée, la tension longitudinale et la forme de l'enveloppe sont strictement imposées. Les ballons de la nouvelle génération sont globalement cylindriques et leurs pôles sont réunis par un câble axial, chargé de transmettre une partie des efforts depuis le crochet (pôle inférieur), directement au pôle supérieur. De plus, la zone latérale cylindrique est soumise à un faible champ de tensions circonférencielles. Ainsi, deux paramètres permettent de faire évoluer la distribution des tensions et la forme de l'enveloppe: - la tension du câble de liaison entre pôles (ou la longueur de ce câble) - la tension circonférencielle moyenne désirée (ou le rayon du ballon). On peut donc calculer et réaliser: - soit des ballons de forme adaptée, comme les ballons à fond plat pour le bon fonctionnement des montgolfières infrarouge (projet MIR); - soit des ballons optimisés pour une bonne répartition des contraintes et une meilleure utilisation des matériaux d'enveloppe, pour l'ensemble des programmes stratosphériques. Il s'ensuit une économie sensible des coûts de fabrication, une fiabilité accrue du fonctionnement de ces ballons et une rendement opérationnel bien supérieur, permettant entre autres, d'envisager des vols à très haute altitude en matériaux très légers.

Diethylstilbestrol (DES) and Cancer

MedlinePlus

... Genetics Services Directory Cancer Prevention Overview Research Diethylstilbestrol (DES) and Cancer On This Page What is DES? ... outlined in the table below. Fertility Problems in DES Daughters ( 7 ) Fertility Complication Hazard Ratio Percent Cumulative ...

Spatial and Temporal Distribution of Current-Use Pesticides in Atmospheric Particulate Matter in Houston, Texas.

PubMed

Clark, Adelaide E; Yoon, Subin; Sheesley, Rebecca J; Usenko, Sascha

2016-12-01

The atmospheric concentrations of seven current-use pesticides in particulate matter were determined at four locations throughout the Houston metropolitan area in TSP and PM 2.5 samples from September 2013. Atmospheric concentrations in both TSP and PM 2.5 ranged from below method detection limits (MDLs) to nearly 1100 pg m -3 . The three compounds most frequently detected above MDLs were chlorothalonil, bifenthrin, and λ-cyhalothrin. Atmospheric chlorothalonil concentrations were above 800 pg m -3 in several TSP samples, but detected above MDLs in all samples, differed between urban and suburban sites, while also being more associated with fine particulate matter. λ-cyhalothrin had high atmospheric concentrations at one of the suburban sites and the industrial site, but was

Influence des traitements thermiques et de la microstructure sur les phénomènes de découplage dans les composés au bismuth

NASA Astrophysics Data System (ADS)

Nicolas, M.; Guyen van Huong, C. N.; Burger, J. P.; Dubon, A.; Fitoussi, J. P.; Laval, J. Y.

1991-11-01

a.c. susceptibility measurements and 3D electronic microscopy observation were carried out on three Bi-compounds (2212 and 2223). Depending on the annealing conditions, one observes lamellar-type materials organized either in a more or less dense structure of fine particles or in very large slabs. The a.c. susceptibility signals allow to separate the intergranular from the intragranular effects. The combined results obtained by both techniques lead us to conclude that the intergranular and the intragranular decoupling, induced by magnetic fields are of same nature, i.e. occur at the (BiO)2 slab. Nous avons couplé des mesures de susceptibilité altemative et d'observation au microscope électronique en 3D sur trois échantillons supraconducteurs au bismuth (2212 et 2223). Selon les conditions de recuit, on observe des matériaux de type lamellaire, organisés soit en une structure plus ou moins dense de fines particules, soit en larges plaquettes. L'étude des signaux de susceptibilité alternative χ' et χ'' permet de séparer les effets intergranulaires des effets intragranulaires. les résultats combinés des deux techniques nous ont conduit à conclure que les deux types de découplage (inter et intragranulaires), induits par les champs magnétiques sont de même nature, c'est-à-dire se produisent au niveau des bicouches (BiO)2.

Maladie des vibrations

PubMed Central

Shen, Shixin (Cindy); House, Ronald A.

2017-01-01

Résumé Objectif Permettre aux médecins de famille de comprendre l’épidémiologie, la pathogenèse, les symptômes, le diagnostic et la prise en charge de la maladie des vibrations, une maladie professionnelle importante et courante au Canada. Sources d’information Une recherche a été effectuée sur MEDLINE afin de relever les recherches et comptes rendus portant sur la maladie des vibrations. Une recherche a été effectuée sur Google dans le but d’obtenir la littérature grise qui convient au contexte canadien. D’autres références ont été tirées des articles relevés. Message principal La maladie des vibrations est une maladie professionnelle répandue touchant les travailleurs de diverses industries qui utilisent des outils vibrants. La maladie est cependant sous-diagnostiquée au Canada. Elle compte 3 éléments : vasculaire, sous la forme d’un phénomène de Raynaud secondaire; neurosensoriel; et musculosquelettique. Aux stades les plus avancés, la maladie des vibrations entraîne une invalidité importante et une piètre qualité de vie. Son diagnostic exige une anamnèse minutieuse, en particulier des antécédents professionnels, un examen physique, des analyses de laboratoire afin d’éliminer les autres diagnostics, et la recommandation en médecine du travail aux fins d’investigations plus poussées. La prise en charge consiste à réduire l’exposition aux vibrations, éviter les températures froides, abandonner le tabac et administrer des médicaments. Conclusion Pour assurer un diagnostic rapide de la maladie des vibrations et améliorer le pronostic et la qualité de vie, les médecins de famille devraient connaître cette maladie professionnelle courante, et pouvoir obtenir les détails pertinents durant l’anamnèse, recommander les patients aux cliniques de médecine du travail et débuter les demandes d’indemnisation de manière appropriée. PMID:28292812

40 CFR 60.422 - Standards for particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standards for particulate matter. 60... Manufacture § 60.422 Standards for particulate matter. On or after the date on which the performance test... sulfate dryer, particulate matter at an emission rate exceeding 0.15 kilogram of particulate per megagram...

40 CFR 60.422 - Standards for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standards for particulate matter. 60... Manufacture § 60.422 Standards for particulate matter. On or after the date on which the performance test... sulfate dryer, particulate matter at an emission rate exceeding 0.15 kilogram of particulate per megagram...

40 CFR 60.422 - Standards for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standards for particulate matter. 60... Manufacture § 60.422 Standards for particulate matter. On or after the date on which the performance test... sulfate dryer, particulate matter at an emission rate exceeding 0.15 kilogram of particulate per megagram...

40 CFR 60.422 - Standards for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standards for particulate matter. 60... Manufacture § 60.422 Standards for particulate matter. On or after the date on which the performance test... sulfate dryer, particulate matter at an emission rate exceeding 0.15 kilogram of particulate per megagram...

Etat des lieux des soins de premier recours des malades mentaux à Antananarivo : étude rétrospective

PubMed Central

Bakohariliva, Hasina Andrianarivony; Rafehivola, Imisanavalona Hanitrinihaja; Raobelle, Evah Norotiana; Raharivelo, Adeline; Rajaonarison, Bertille Hortense

2018-01-01

Résumé Religion et guérisseurs traditionnels occupent encore une place prépondérante dans la prise en charge des maladies mentales à Madagascar. Ainsi, nous nous sommes fixés comme objectif d'établir un état des lieux sur les soins de premier recours des malades mentaux. Nous avons mené une étude rétrospective descriptive s'étalant sur une période de 16 mois allant de janvier 2014 en avril 2015 au sein du service de psychiatrie du CHU de Befelatanana à Antananarivo. La prévalence des psychoses était de 25%. Le genre féminin (53%), l'ethnie merina (77%), les étudiants (45%), le niveau d'étude secondaire (40%), les célibataires (72%), la religion protestante (45%), ainsi que le niveau socio-économique moyen (57,5%) étaient prédominants. Dans les paramètres cliniques, le mode de début brutal (52%), le premier recours à la religion (40%), la présence d'antécédents des cas similaire (90%), étaient majoritaires. La schizophrénie était la pathologie la plus rencontrée dans la moitié des cas. Le délai d'amélioration en cas de traitement religieux et traditionnels était dans la moitié des cas de plus de 10 jours d'hospitalisation. Les patients ayant reçu une prise en charge psychiatrique en premier recours, étaient améliorés dans 75 % cas en moins de 10jours. Le retard du recours aux soins psychiatriques est une réalité à Madagascar qui aggrave le pronostic des psychoses. PMID:29632623

Airborne particulate in Varanasi over middle Indo-Gangetic Plain: variation in particulate types and meteorological influences.

PubMed

Murari, Vishnu; Kumar, Manish; Mhawish, Alaa; Barman, S C; Banerjee, Tirthankar

2017-04-01

The variation in particulate mass and particulate types (PM 2.5 and PM 10 ) with respect to local/regional meteorology was analyzed from January to December 2014 (n = 104) for an urban location over the middle Indo-Gangetic Plain (IGP). Both coarser (mean ± SD; PM 10 161.3 ± 110.4 μg m -3 , n = 104) and finer particulates (PM 2.5 81.78 ± 66.4 μg m -3 ) revealed enormous mass loading with distinct seasonal effects (range: PM 10 12-535 μg m -3 ; PM 2.5 8-362 μg m -3 ). Further, 56% (for PM 2.5 ) to 81% (for PM 10 ) of monitoring events revealed non-attainment national air quality standard especially during winter months. Particulate types (in terms of PM 2.5 /PM 10 0.49 ± 0.19) also exhibited temporal variations with high PM 2.5 loading particularly during winter (0.62) compared to summer months (0.38). Local meteorology has clear distinguishing trends in terms of dry summer (March to June), wet winter (December to February), and monsoon (July to September). Among all the meteorological variables (average temperature, rainfall, relative humidity (RH), wind speed (WS)), temperature was found to be inversely related with particulate loading (r PM10 -0.79; r PM2.5 -0.87) while RH only resulted a significant association with PM 2.5 during summer (r PM10 0.07; r PM2.5 0.55) and with PM 10 during winter (r PM10 0.53; r PM2.5 0.24). Temperature, atmospheric boundary layer (ABL), and RH were cumulatively recognized as the dominant factors regulating particulate concentration as days with high particulate loading (PM 2.5 >150 μg m -3 ; PM 10 >260 μg m -3 ) appeared to have lower ABL (mean 660 m), minimum temperature (<22.6 °C), and high RH (∼79%). The diurnal variations of particulate ratio were mostly insignificant except minor increases during night having a high wintertime ratio (0.58 ± 0.07) over monsoon (0.34 ± 0.05) and summer (0.30 ± 0.07). Across the region, atmospheric visibility appeared to be inversely associated with

Electrically heated particulate filter propagation support methods and systems

DOEpatents

Gonze, Eugene V [Pinckney, MI; Ament, Frank [Troy, MI

2011-06-07

A control system that controls regeneration of a particulate filter is provided. The system generally includes a regeneration module that controls current to the particulate filter to initiate combustion of particulate matter in the particulate filter. A propagation module estimates a propagation status of the combustion of the particulate matter based on a combustion temperature. A temperature adjustment module controls the combustion temperature by selectively increasing a temperature of exhaust that passes through the particulate filter.

Comprendre la maltraitance des aînés en pratique familiale

PubMed Central

Yaffe, Mark J.; Tazkarji, Bachir

2012-01-01

Résumé Objectif Présenter ce qui constitue la maltraitance des aînés, ce dont les médecins de famille devraient être au courant, les signes et les symptômes laissant présager de mauvais traitements chez des adultes plus âgés, comment l’outil Elder Abuse Suspicion Index peut aider à détecter la maltraitance et les options qui existent pour réagir en cas de soupçons de maltraitance. Sources des données On a fait une recension dans MEDLINE, PsycINFO et Social Work Abstracts pour trouver des publications en français ou en anglais, de 1970 à 2011, à l’aide des expressions elder abuse, elder neglect, elder mistreatment, seniors, older adults, violence, identification, detection tools et signs and symptoms. Les publications pertinentes ont fait l’objet d’un examen. Message principal La maltraitance des aînés est une cause importante de morbidité et de mortalité chez les adultes plus âgés. Si les médecins de famille sont bien placés pour détecter des mauvais traitements infligés aux aînés, leurs taux réels de signalement de cas de maltraitance sont plus faibles que dans d’autres professions. Cette situation pourrait s’améliorer s’ils comprenaient mieux les genres d’agissements qui constituent de la maltraitance des aînés, ainsi que les signes et les symptômes observés au bureau qui pourraient pointer vers des cas de mauvais traitements. La détection de tels cas pourrait être facilitée par le recours à un court outil validé, comme l’Elder Abuse Suspicion Index. Conclusion Les médecins de famille peuvent jouer un rôle plus important dans la détection d’une éventuelle maltraitance des aînés. Une fois qu’on soupçonne de mauvais traitements, il existe dans la plupart des communautés des services sociaux ou des forces de l’ordre accessibles pour effectuer des évaluations plus approfondies et intervenir.

Powder and particulate production of metallic alloys

NASA Technical Reports Server (NTRS)

Grant, N. J.

1982-01-01

Developments of particulate metallurgy of alloyed materials where the final products is a fully dense body are discussed. Particulates are defined as powders, flakes, foils, silvers, ribbons and strip. Because rapid solidification is an important factor in particulate metallurgy, all of the particulates must have at least one dimension which is very fine, sometimes as fine as 10 to 50 microns, but move typically up to several hundred microns, provided that the dimension permits a minimum solidification rate of at least 100 K/s.

Electrically heated particulate filter embedded heater design

DOEpatents

Gonze, Eugene V.; Chapman, Mark R.

2014-07-01

An exhaust system that processes exhaust generated by an engine is provided. The system generally includes a particulate filter (PF) that filters particulates from the exhaust wherein an upstream end of the PF receives exhaust from the engine and wherein an upstream surface of the particulate filter includes machined grooves. A grid of electrically resistive material is inserted into the machined grooves of the exterior upstream surface of the PF and selectively heats exhaust passing through the grid to initiate combustion of particulates within the PF.

Identification des objets et detection de leur alignement en utilisant la technologie RFID

NASA Astrophysics Data System (ADS)

Rahma, Zayoud

De nos jours, les vehicules motorises sont essentiels dans notre vie quotidienne, d'ou la necessite de leur approvisionnement en carburant. L'approvisionnement en carburant peut entrainer certains inconvenients, tels que: les files d'attente, la disponibilite non-continuelle du carburant et les fraudes. Les problemes d'attente et de disponibilite non-continuelle du carburant peuvent etre facilement resolus en allant a une autre station d'essence aux alentours si disponibles. Par contre le probleme de fraudes est plus difficile a resoudre. De ce fait, decoule notre solution qui consiste a developper un systeme intelligent pour la gestion d'approvisionnement en carburant afin de remedier a ce probleme de fraudes. Pour des raisons de surete, il faut eviter les risques d'etincelles dans l'environnement du carburant. En particulier, il convient de ne pas utiliser un systeme utilisant 1'electricite proche de la pompe, du tuyau ou du reservoir du carburant du vehicule. Nous avons choisi la technologie RFID (Radio Frequency IDentification) et avons opte pour l'utilisation des etiquettes passives, etant donne que les etiquettes semi-passives ou actives contiennent une batterie electrique et sont nettement plus cheres. Un vehicule motorise sera identifie avec une etiquette RFID passive collee au-dessus du goulot de son reservoir. Deux autres etiquettes RFID seront placees sur le pistolet de sorte que le flux du carburant ne sera autorise que lorsque les trois etiquettes sont alignees. Notre travail etait a la demande d'une entreprise petroliere ayant une chaine internationale de stations de carburant. Le travail consiste en la conception, par la recherche, du systeme requis et s'articule sur l'optimisation de la topologie des antennes et des etiquettes de sorte que le systeme juge qu'il y a alignement lorsque le bec du pistolet est fonce dans le goulot du reservoir, et par consequent autorise le versement du carburant. Dans tous les autres cas, le systeme doit juger qu'il n

Litigation involving DES.

PubMed

Rheingold, P D

1976-01-01

Focus is on the diethylstilbestrol (DES) litigation which has resulted from the 1971 discovery that this synthetic estrogen can cause cancer in the daughters of women who used the drug during pregnancy in an effort to prevent threatened abortion. Possibly 100 suits are pending at this time in which DES daughters claim injuries. In most of these vaginal or cervical cancer has appeared -- with or without a hysterectomy having been performed. Several women died from cancer. The fact that the use of DES occurred many years ago is the legal hurdle most troublesome to lawyers. The average women coming to a lawyer's office today has a mother who used some form of DES, perhaps in 1955. Few drugstores have records today of the prescriptions which they filled 20 years ago. It has been estimated that over the 1950-1970 period more than 200 different companies manufactured or "tabletized" under their own name DES plus a variety of similar synthetic estrogens promoted for the prevention of threatened abortion. A further hurdle caused by the passage of time is that even the records of the physicians are frequently lost. A final problem created by the age of the cases is statute of limitations. If the actual manufacturer of the DES cannot be identified, this is generally the end of the lawyer's interest in the case. The chance of the plaintiff winning may be increased if the action against all the manufacturers is a class action. Most of the pending DES suits are against the manufacturer and not against the doctor. Thus far no DES case has been tried to completion. Several have been settled by the manufacturers on the eve of the trial, generally for less than the full sum that a cancer victim would expect to receive.

Médecine des voyages

PubMed Central

Aw, Brian; Boraston, Suni; Botten, David; Cherniwchan, Darin; Fazal, Hyder; Kelton, Timothy; Libman, Michael; Saldanha, Colin; Scappatura, Philip; Stowe, Brian

2014-01-01

Résumé Objectif Définir la pratique de la médecine des voyages, présenter les éléments fondamentaux d’une consultation complète préalable aux voyages à des voyageurs internationaux et aider à identifier les patients qu’il vaudrait mieux envoyer en consultation auprès de professionnels de la médecine des voyages. Sources des données Les lignes directrices et les recommandations sur la médecine des voyages et les maladies liées aux voyages publiées par les autorités sanitaires nationales et internationales ont fait l’objet d’un examen. Une recension des ouvrages connexes dans MEDLINE et EMBASE a aussi été effectuée. Message principal La médecine des voyages est une spécialité très dynamique qui se concentre sur les soins préventifs avant un voyage. Une évaluation exhaustive du risque pour chaque voyageur est essentielle pour mesurer avec exactitude les risques particuliers au voyageur, à son itinéraire et à sa destination et pour offrir des conseils sur les interventions les plus appropriées en gestion du risque afin de promouvoir la santé et prévenir les problèmes médicaux indésirables durant le voyage. Des vaccins peuvent aussi être nécessaires et doivent être personnalisés en fonction des antécédents d’immunisation du voyageur, de son itinéraire et du temps qu’il reste avant son départ. Conclusion La santé et la sécurité d’un voyageur dépendent du degré d’expertise du médecin qui offre le counseling préalable à son voyage et les vaccins, au besoin. On recommande à ceux qui donnent des conseils aux voyageurs d’être conscients de l’ampleur de cette responsabilité et de demander si possible une consultation auprès de professionnels de la médecine des voyages pour tous les voyageurs à risque élevé.

Electrically heated particulate filter using catalyst striping

DOEpatents

Gonze, Eugene V; Paratore, Jr., Michael J; Ament, Frank

2013-07-16

An exhaust system that processes exhaust generated by an engine is provided. The system generally includes a particulate filter (PF) that filters particulates from the exhaust wherein an upstream end of the PF receives exhaust from the engine. A grid of electrically resistive material is applied to an exterior upstream surface of the PF and selectively heats exhaust passing through the grid to initiate combustion of particulates within the PF. A catalyst coating is applied to the PF that increases a temperature of the combustion of the particulates within the PF.

Micromechanics for particulate reinforced composites

NASA Technical Reports Server (NTRS)

Murthy, Pappu L. N.; Goldberg, Robert K.; Mital, Subodh K.

1996-01-01

A set of micromechanics equations for the analysis of particulate reinforced composites is developed using the mechanics of materials approach. Simplified equations are used to compute homogenized or equivalent thermal and mechanical properties of particulate reinforced composites in terms of the properties of the constituent materials. The microstress equations are also presented here to decompose the applied stresses on the overall composite to the microstresses in the constituent materials. The properties of a 'generic' particulate composite as well as those of a particle reinforced metal matrix composite are predicted and compared with other theories as well as some experimental data. The micromechanics predictions are in excellent agreement with the measured values.

Spacecraft particulate sizing spectrometer

NASA Technical Reports Server (NTRS)

Miranda, Henry A., Jr.

1992-01-01

An evaluation prototype device is described, together with conclusions and several recommendations for follow-on flight hardware. The device detects individual particles crossing an external sensing zone, and produces a histogram displaying the size distribution of particles sensed, over the nominal range of 5 to 50 microns. The output is totally independent of the particle refractive index, and is also largely unaffected by particle shape. The reported diameters are in terms of the equivalent sphere, as judged by the scattered light intercepted by the receiving channels, which develop signals whenever a particle crosses the beam of illumination in the sensing zone. Supporting evidence for the latter assertion is discussed on the basis of experimental test data for non-spherical particulates. Also included is a technical appendix which presents theoretical arguments that provide a firm foundation for this assertion.

Characterization of organic particulates present in milk factory process waters used for reuse along with aerobically digested effluent wastewater.

PubMed

Verheyen, Vincent; Cruickshank, Alicia; Wild, Karl; Heaven, Michael W; McGee, Rachel; Watkins, Mark; Nash, David

2011-01-01

Wastewater from a dairy processor is being reused and recycled both within the plant and for irrigation. Flash pyrolysis GC-MS was used to examine nitrogen and phenol containing compounds (M.W.=35 to 450 g/mol) in the particulate fraction of the milk condensate, combined clean wastewater and aerobic bioreactor effluent. For comparison, the particulates were also prepared for standard GC-MS analyses using conventional solvent extraction methods. Compounds detected by pyrolysis GC-MS were found mostly in the bioreactor with the amino acid arginine (220 mg/kg) and the amino acid derivative 1-methyl-5-oxo-L-proline methyl ester (130 mg/kg) found at the highest concentrations. In comparison, sterols detected in the effluent were found at higher concentrations when using solvent extraction indicating some degradation with pyrolysis GC-MS. However, with few exceptions, particulates were generally found not to act as passive collectors capable of concentrating less water soluble chemicals. Crown Copyright © 2010. Published by Elsevier Ltd. All rights reserved.

Environmentally Persistent Free Radical (EPFRs) - Ambient Air Particulates, Soils and Fate of Some Pollutants

NASA Astrophysics Data System (ADS)

Lomnicki, S. M.

2017-12-01

Environmentally Persistent Free Radicals (EPFRs) are relatively recently discovered species that are present on ambient air particulates. Their origin is typically associated with the combustion borne PM, where in the cool zone of the combustion process aromatic precursors react with the metal centers of particulates forming surface-organic complex with radical characteristics. EPFRs have been found to be sufficiently resistant to be emitted from the combustion sources and persist in the ambient air on particulates. Their inhalation has been associated with severe health effects, and potentially are one of the major agents contributing the epidemiological risks of PM exposure. Interestingly, EPFRs can be formed not only at the elevated temperatures but also in ambient conditions, where the contact of precursor molecules with transition metal (but not only) domains can result in adsorbate complexes. In fact, EPFRs have been detected in the contaminated soils, or during the oil spill incidents. It is very likely, that the interaction of some molecules released to the air can result in the formation of EPFRs on the ambient air particulates in atmospheric conditions. These species can be a natural degradation by-products that lead to the formation of oxygenated organics in ambient atmosphere.

Characteristics of particulate matter emissions from toy cars with electric motors.

PubMed

Wang, Xiaofei; Williams, Brent J; Biswas, Pratim

2015-04-01

Aerosol emissions from toy cars with electric motors were characterized. Particle emission rates from the toy cars, as high as 7.47×10(7) particles/s, were measured. This emission rate is lower than other indoor sources such as smoking and cooking. The particles emitted from toy cars are generated from spark discharges inside the electric motors that power the toy cars. Size distribution measurements indicated that most particles were below 100 nm in diameter. Copper was the dominant inorganic species in these particles. By deploying aerosol mass spectrometers, high concentrations of particulate organic matter were also detected and characterized in detail. Several organic compounds were identified using a thermal desorption aerosol gas chromatography. The mass size distribution of particulate organic matter was bimodal. The formation mechanism of particulate organic matter from toy cars was elucidated. A possible new source of indoor air pollution, particles from electric motors in toy cars, was identified. This study characterized aerosol emissions from toy cars in detail. Most of these particles have a diameter less than 100 nm. Copper and some organics are the major components of these particles. Conditions that minimize these emissions were determined.

Apparatus and method for noninvasive particle detection using doppler spectroscopy

DOEpatents

Sinha, Dipen N.

2016-05-31

An apparatus and method for noninvasively detecting the presence of solid particulate matter suspended in a fluid flowing through a pipe or an oil and gas wellbore are described. Fluid flowing through a conduit containing the particulate solids is exposed to a fixed frequency (>1 MHz) of ultrasonic vibrations from a transducer attached to the outside of the pipe. The returning Doppler frequency shifted signal derived from the scattering of sound from the moving solid particles is detected by an adjacent transducer. The transmitted signal and the Doppler signal are combined to provide sensitive particulate detection. The magnitude of the signal and the Doppler frequency shift are used to determine the particle size distribution and the velocity of the particles. Measurement of the phase shift between the applied frequency and the detected Doppler shifted may be used to determine the direction of motion of the particles.

Sedimentary particulate iron: the missing micronutrients ?

NASA Astrophysics Data System (ADS)

Beghoura, Houda; Gorgues, Thomas; Aumont, Olivier; Planquette, Hélène

2017-04-01

Iron is known to regulate the marine primary production and to impact the structure of ecosystems. Indeed, iron is the limiting nutrient for the phytoplankton growth over about 30% of the global ocean. However, the nature of the external sources of iron to the ocean and their quantification remain uncertain. Among these external sources, the sediment sources have been recently shown to be underestimated. Besides, since the operationally defined dissolved iron (which is the sum of truly dissolved and colloidal iron) was traditionally assumed to be the only form available to phytoplankton and bacteria, most studies have focused on the supply of dissolved iron to the ocean, the role of the particulate fraction of iron being largely ignored. This traditional view has been recently challenged, noticeably, by observational evidences. Indeed, in situ observations have shown that large amounts of particulate iron are being resuspended from continental margins to the open ocean thanks to fine grained particles' transport over long distances. A fraction of this particulate iron may dissolve and thereby fuel the phytoplankton growth. The magnitude of the sedimentary sources of particulate iron and the releasing processes affecting this iron phase are not yet well constrained or quantified. As a consequence, the role of sedimentary particulate iron in the biogeochemical cycles is still unclear despite its potentially major widespread importance. Here, we propose a modeling exercise to assess the first order impacts of this newly considered particulate sedimentary iron on global ocean biogeochemistry. We designed global experiments with a coupled dynamical-biogeochemical model (NEMO-PISCES). First, a control simulation that includes only a sediment source of iron in the dissolved phase has been run. Then, this control simulation is being compared with simulations, in which we include a sediment source of iron in both phases (dissolved as well as particulate). Those latter

Determination of Methylamines and Trimethylamine-N-oxide in particulate matter by non-suppressed ion chromatography

USDA-ARS?s Scientific Manuscript database

An ion chromatography method with non-suppressed conductivity detection was developed for the simultaneous determination of methylamines (methylamine, dimethylamine, trimethylamine) and trimethylamine-N-oxide in particulate matter air samples. The analytes were well separated by means of cation-exch...

Study of the use of Metal-Oxide-Silicon (MOS) devices for particulate detection and monitoring in the earth's atmosphere

NASA Technical Reports Server (NTRS)

Brooks, A. D.; Monteith, L. K.; Wortman, J. J.; Mulligan, J. C.

1974-01-01

A metal-oxide-silicon (MOS) capacitor-type particulate sensor was evaluated for use in atmospheric measurements. An accelerator system was designed and tested for the purpose of providing the necessary energy to trigger the MOS-type sensor. The accelerator system and the MOS sensor were characterized as a function of particle size and velocity. Diamond particles were used as particulate sources in laboratory tests. Preliminary tests were performed in which the detector was mounted on an aircraft and flown in the vicinity of coal-fired electric generating plants.

Understanding particulate coating microstructure development

NASA Astrophysics Data System (ADS)

Roberts, Christine Cardinal

How a dispersion of particulates suspended in a solvent dries into a solid coating often is more important to the final coating quality than even its composition. Essential properties like porosity, strength, gloss, particulate order, and concentration gradients are all determined by the way the particles come together as the coating dries. Cryogenic scanning electron microscopy (cryoSEM) is one of the most effective methods to directly visualize a drying coating during film formation. Using this method, the coating is frozen, arresting particulate motion and solidifying the sample so that it be imaged in an SEM. In this thesis, the microstructure development of particulate coatings was explored with several case studies. First, the effect of drying conditions was determined on the collapse of hollow latex particles, which are inexpensive whiteners for paint. Using cryoSEM, it was found that collapse occurs during the last stages of drying and is most likely to occur at high drying temperatures, humidity, and with low binder concentration. From these results, a theoretical model was proposed for the collapse of a hollow latex particle. CryoSEM was also used to verify a theoretical model for the particulate concentration gradients that may develop in a coating during drying for various evaporation, sedimentation and particulate diffusion rates. This work created a simple drying map that will allow others to predict the character of a drying coating based on easily calculable parameters. Finally, the effect of temperature on the coalescence and cracking of latex coatings was explored. A new drying regime for latex coatings was identified, where partial coalescence of particles does not prevent cracking. Silica was shown to be an environmentally friendly additive for preventing crack formation in this regime.

[Contamination of urban air in a snowy district with 1-nitropyrene and particulate matter during the winter].

PubMed

Saitoh, N; Wada, Y; Koizumi, A; Kamiyama, S

1990-10-01

Nitroarenes, potent rodent carcinogens, have attracted much attention as environmental contaminants. Recently, simultaneous exposure to dust have been found to potentiate tumorigenicity of nitroarenes in rats (14). We hypothesized that inhabitants of northwestern Japan may be exposed to such substances in winter. First, we sought to develop a sensitive yet time saving method to determine nitroarene concentrations in airborne particulate matter. The method developed used a high-performance liquid chromatograph equipped with a fluorescence detector. By on-column catalytic reduction, using silica coated with platinum and rhodium, 1-nitropyrene (1-NP), 1,3-dinitropyrene, 1,6-dinitropyrene, and 1,8-dinitropyrene were effectively reduced to their amino derivatives which were easily detectable with the fluorescence detector. The lowest detectable limits found using the present method were on the order of picograms for individual compounds. Subsequently, we sought to determine the concentrations of nitroarenes using the new method on airborne particulate matter during the period from November to April. Samples were collected at sampling sites on road with high-volume air samplers for 24 hours or 72 hours in four different rural areas in Iwate Prefecture. At one location in the city of Morioka, samples were collected at the height of 25 m from the ground. Among the four nitropyrenes mentioned above, only 1-NP was detected in the samples. The concentrations of 1-NP and airborne particulates changed significantly in all examined areas in parallel with the rise and fall of the frequencies of studded tire use. The highest 1-NP and airborne particulate concentrations were 1.210 pg/m3 and 1,291 micrograms/m3, respectively, being recorded at the busiest road in Kitakami. In contrast, the lowest values were 38 to 66 pg/m3 for 1-NP and 54 to 94 micrograms/m3 for airborne particulates in Morioka, being recorded in November and April, respectively. The mutagenicities of extracts of

Etude numerique et experimentale de la reponse vibro-acoustique des structures raidies a des excitations aeriennes et solidiennes

NASA Astrophysics Data System (ADS)

Mejdi, Abderrazak

Les fuselages des avions sont generalement en aluminium ou en composite renforces par des raidisseurs longitudinaux (lisses) et transversaux (cadres). Les raidisseurs peuvent etre metalliques ou en composite. Durant leurs differentes phases de vol, les structures d'avions sont soumises a des excitations aeriennes (couche limite turbulente : TBL, champs diffus : DAF) sur la peau exterieure dont l'energie acoustique produite se transmet a l'interieur de la cabine. Les moteurs, montes sur la structure, produisent une excitation solidienne significative. Ce projet a pour objectifs de developper et de mettre en place des strategies de modelisations des fuselages d'avions soumises a des excitations aeriennes et solidiennes. Tous d'abord, une mise a jour des modeles existants de la TBL apparait dans le deuxieme chapitre afin de mieux les classer. Les proprietes de la reponse vibro-acoustique des structures planes finies et infinies sont analysees. Dans le troisieme chapitre, les hypotheses sur lesquelles sont bases les modeles existants concernant les structures metalliques orthogonalement raidies soumises a des excitations mecaniques, DAF et TBL sont reexamines en premier lieu. Ensuite, une modelisation fine et fiable de ces structures est developpee. Le modele est valide numeriquement a l'aide des methodes des elements finis (FEM) et de frontiere (BEM). Des tests de validations experimentales sont realises sur des panneaux d'avions fournis par des societes aeronautiques. Au quatrieme chapitre, une extension vers les structures composites renforcees par des raidisseurs aussi en composites et de formes complexes est etablie. Un modele analytique simple est egalement implemente et valide numeriquement. Au cinquieme chapitre, la modelisation des structures raidies periodiques en composites est beaucoup plus raffinee par la prise en compte des effets de couplage des deplacements planes et transversaux. L'effet de taille des structures finies periodiques est egalement pris en

40 CFR 52.2059 - Control strategy: Particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 5 2012-07-01 2012-07-01 false Control strategy: Particulate matter... Control strategy: Particulate matter. (a) Pennsylvania has committed to undertake a comprehensive program... Investigating and Controlling Nontraditional Particulate Matter Emissions Task Completion date Scheduled tasks...

40 CFR 52.2059 - Control strategy: Particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 5 2013-07-01 2013-07-01 false Control strategy: Particulate matter... Control strategy: Particulate matter. (a) Pennsylvania has committed to undertake a comprehensive program... Investigating and Controlling Nontraditional Particulate Matter Emissions Task Completion date Scheduled tasks...

40 CFR 52.2059 - Control strategy: Particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control strategy: Particulate matter... Control strategy: Particulate matter. (a) Pennsylvania has committed to undertake a comprehensive program... Investigating and Controlling Nontraditional Particulate Matter Emissions Task Completion date Scheduled tasks...

40 CFR 52.2059 - Control strategy: Particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 4 2011-07-01 2011-07-01 false Control strategy: Particulate matter... Control strategy: Particulate matter. (a) Pennsylvania has committed to undertake a comprehensive program... Investigating and Controlling Nontraditional Particulate Matter Emissions Task Completion date Scheduled tasks...

Monitoring diesel particulate matter and calculating diesel particulate densities using Grimm model 1.109 real-time aerosol monitors in underground mines.

PubMed

Kimbal, Kyle C; Pahler, Leon; Larson, Rodney; VanDerslice, Jim

2012-01-01

Currently, there is no Mine Safety and Health Administration (MSHA)-approved sampling method that provides real-time results for ambient concentrations of diesel particulates. This study investigated whether a commercially available aerosol spectrometer, the Grimm Portable Aerosol Spectrometer Model 1.109, could be used during underground mine operations to provide accurate real-time diesel particulate data relative to MSHA-approved cassette-based sampling methods. A subset was to estimate size-specific diesel particle densities to potentially improve the diesel particulate concentration estimates using the aerosol monitor. Concurrent sampling was conducted during underground metal mine operations using six duplicate diesel particulate cassettes, according to the MSHA-approved method, and two identical Grimm Model 1.109 instruments. Linear regression was used to develop adjustment factors relating the Grimm results to the average of the cassette results. Statistical models using the Grimm data produced predicted diesel particulate concentrations that highly correlated with the time-weighted average cassette results (R(2) = 0.86, 0.88). Size-specific diesel particulate densities were not constant over the range of particle diameters observed. The variance of the calculated diesel particulate densities by particle diameter size supports the current understanding that diesel emissions are a mixture of particulate aerosols and a complex host of gases and vapors not limited to elemental and organic carbon. Finally, diesel particulate concentrations measured by the Grimm Model 1.109 can be adjusted to provide sufficiently accurate real-time air monitoring data for an underground mining environment.

Etude de l'amelioration de la qualite des anodes par la modification des proprietes du brai

NASA Astrophysics Data System (ADS)

Bureau, Julie

La qualite des anodes produites se doit d'etre bonne afin d'obtenir de l'aluminium primaire tout en reduisant le cout de production du metal, la consommation d'energie et les emissions environnementales. Or, l'obtention des proprietes finales de l'anode necessite une liaison satisfaisante entre le coke et le brai. Toutefois, la matiere premiere actuelle n'assure pas forcement la compatibilite entre le coke et le brai. Une des solutions les plus prometteuses, pour ameliorer la cohesion entre ces deux materiaux, est la modification des proprietes du brai. L'objectif de ce travail consiste a modifier les proprietes du brai par l'ajout d'additifs chimiques afin d'ameliorer la mouillabilite du coke par le brai modifie pour produire des anodes de meilleure qualite. La composition chimique du brai est modifiee en utilisant des tensioactifs ou agents de modification de surface choisis dans le but d'enrichir les groupements fonctionnels susceptibles d'ameliorer la mouillabilite. L'aspect economique, l'empreinte environnementale et l'impact sur la production sont consideres dans la selection des additifs chimiques. Afin de realiser ce travail, la methodologie consiste a d'abord caracteriser les brais non modifies, les additifs chimiques et les cokes par la spectroscopie infrarouge a transformee de Fourier (FTIR) afin d'identifier les groupements chimiques presents. Puis, les brais sont modifies en ajoutant un additif chimique afin de possiblement modifier ses proprietes. Differentes quantites d'additif sont ajoutees afin d'examiner l'effet de la variation de la concentration sur les proprietes du brai modifie. La methode FTIR permet d'evaluer la composition chimique des brais modifies afin de constater si l'augmentation de la concentration d'additif enrichit les groupements fonctionnels favorisant l'adhesion coke/brai. Ensuite, la mouillabilite du coke par le brai est observee par la methode goutte- sessile. Une amelioration de la mouillabilite par la modification a l'aide d

Ecoulement et mise en structure de suspensions macroscopiques

NASA Astrophysics Data System (ADS)

Petit, L.

In this review, we report the various experimental studies performed on suspensions of solid particules in liquids, and concerning the rheological behaviour of such systems and the ordering of particules under the applied velocity fields. The number of materials which are flowing suspensions (reagents in chemical engineering, paints while spreading, blood flow, muds in oil reservoir) gave rise to a number of experimental studies, especially in the last twenty years. The results show a wide variety of behaviour, even for systems of intermediate concentration. In addition, even for identical systems, the results depend of the type of flow. Then, it is clear that, in addition of the standard parameters which are to be taken into account, it is necessary to consider the type of flow the suspension is submitted to. The flow influences the spatial distribution of the particules, leading to their ordering or migration. These ordering or motions influence the flow, and then, the rheological behaviour of the whole system. So, there is a feedback mechanism from the ordering to the flow, which explains the experimental observations. Nous reportons dans cette revue les différentes études expérimentales réalisées sur les suspensions de particules solides dans un liquide et qui concernent le comportement rhéologique de ces systèmes ainsi que les mouvements des particules sous l'effet des champs de vitesse imposés. Ces mouvements peuvent conduire soit à des mises en structure, ou encore à des migrations des particules. L'importance du nombre de matériaux qui se présentent sous forme de suspension et qui sont mis en écoulement (réactif en génie chimique, peintures lors de leur mise en place, écoulement sanguin, boues dans les forages pétroliers,...) a motivé un grand nombre de travaux expérimentaux plus fondamentaux sur le sujet, particulièrement dans les vingt dernières années. Les résultats correspondants montrent une très grande diversité des

Apparatus for particulate matter analysis

DOEpatents

Gundel, Lara A.; Apte, Michael G.; Hansen, Anthony D.; Black, Douglas R.

2007-01-30

The apparatus described herein is a miniaturized system for particle exposure assessment (MSPEA) for the quantitative measurement and qualitative identification of particulate content in gases. The present invention utilizes a quartz crystal microbalance (QCM) or other mass-sensitive temperature compensated acoustic wave resonator for mass measurement. Detectors and probes and light sources are used in combination for the qualitative determination of particulate matter.

Method of forming particulate materials for thin-film solar cells

DOEpatents

Eberspacher, Chris; Pauls, Karen Lea

2004-11-23

A method for preparing particulate materials useful in fabricating thin-film solar cells is disclosed. Particulate materials is prepared by the method include for example materials comprising copper and indium and/or gallium in the form of single-phase, mixed-metal oxide particulates; multi-phase, mixed-metal particulates comprising a metal oxide; and multinary metal particulates.

40 CFR 52.776 - Control strategy: Particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 3 2013-07-01 2013-07-01 false Control strategy: Particulate matter...: Particulate matter. Link to an amendment published at 78 FR 28507, May 15, 2013. (a) The requirements of... the secondary standards for particulate matter in the Metropolitan Indianapolis Intrastate Region. (b...

Quantification des besoins en intrants antipaludiques: contribution à l'actualisation des hypothèses pour la quantification des intrants de prise en charge des cas de paludisme grave en République Démocratique du Congo

PubMed Central

Likwela, Joris Losimba; Otokoye, John Otshudiema

2015-01-01

Les formes graves de paludisme à Plasmodium falciparum sont une cause majeure de décès des enfants de moins de 5 ans en Afrique Sub-saharienne. Un traitement rapide dépend de la disponibilité de médicaments appropriés au niveau des points de prestation de service. La fréquence des ruptures de stock des commodités antipaludiques, en particuliers celles utilisées pour le paludisme grave, avait nécessité une mise à jour des hypothèses de quantification. Les données issues de la collecte de routine du PNLP de 2007 à 2012 ont été comparées à celles rapportés par d'autres pays africains et utilisées pour orienter les discussions au cours d'un atelier organisé par le PNLP et ses partenaires techniques et financiers afin de dégager un consensus national. La proportion des cas de paludisme rapportés comme grave en RDC est resté autour d'une médiane de 7% avec un domaine de variation de 6 à 9%. Hormis la proportion rapportée au Kenya (2%), les pays africains ont rapporté une proportion de cas grave variant entre 5 et 7%. Il apparaît que la proportion de 1% précédemment utilisée pour la quantification en RDC a été sous-estimée dans le contexte de la gestion des cas graves sur terrain. Un consensus s'est dégagé autour de la proportion de 5% étant entendu que des efforts de renforcement des capacités seraient déployés afin d'améliorer le diagnostic au niveau des points de prestation des services. PMID:26213595

Determination of particulate lead during MILAGRO/MCMA-2006 using Aerosol Mass Spectrometry

NASA Astrophysics Data System (ADS)

Salcedo, D.; Onasch, T. B.; Aiken, A. C.; Williams, L. R.; de Foy, B.; Cubison, M. J.; Worsnop, D. R.; Molina, L. T.; Jimenez, J. L.

2010-02-01

We report the first measurements of particulate lead (Pb) from Aerodyne Aerosol Mass Spectrometers, which were deployed in and around Mexico City during the Megacity Initiative: Local and Global Research Observations (MILAGRO)/Mexico City Metropolitan Area 2006 (MCMA-2006) field campaigns. The high resolution mass spectrometer of one of the AMS instruments (HR-AMS) and the measured isotopic ratios unequivocally prove the detection of Pb in ambient particles. A substantial fraction of the lead evaporated slowly from the vaporizer of the instruments, which is indicative of species with low volatility at 600 °C. A model was developed in order to estimate the ambient particulate Pb entering the AMS from the signals in the "open" and the "closed" (or "background") mass spectrum modes of the AMS. The model suggests the presence of at least two lead fractions with ~25% of the Pb signal exhibiting rapid evaporation (1/e decay constant, τ<0.1 s) and ~75% exhibiting slow evaporation (τ~2.4 min) at the T0 urban supersite and a different fraction (70% prompt and 30% slow evaporation) at a site northwest from the metropolitan area (PEMEX site). From laboratory experiments with pure Pb(NO3)2 particles, we estimated that the Pb ionization efficiency relative to nitrate (RIEPb) is 0.5. Comparison of time series of AMS Pb with other measurements carried out at T0 (using Proton Induced X-ray Emission (PIXE), Inductively-Coupled Plasma Mass Spectrometry (ICP-MS) and single-particle counts from an Aerosol Time-of-Fight Mass Spectrometer (ATOFMS)) shows similar levels (for PIXE and ICP-MS) and substantial correlation. During part of the campaign, sampling at T0 was alternated every 10 min with an Aerosol Concentrator, which enabled the detection of signals for PbCl+ and PbS+ ions. PbS+ displays the signature of a slowly evaporating species, while PbCl+ appears to arise only from fast evaporation, which is likely due to the higher vapor pressure of the compounds generating Pb

Determination of particulate lead using aerosol mass spectrometry: MILAGRO/MCMA-2006 observations

NASA Astrophysics Data System (ADS)

Salcedo, D.; Onasch, T. B.; Aiken, A. C.; Williams, L. R.; de Foy, B.; Cubison, M. J.; Worsnop, D. R.; Molina, L. T.; Jimenez, J. L.

2010-06-01

We report the first measurements of particulate lead (Pb) from Aerodyne Aerosol Mass Spectrometers, which were deployed in and around Mexico City during the Megacity Initiative: Local and Global Research Observations (MILAGRO)/Mexico City Metropolitan Area 2006 (MCMA-2006) field campaigns. The high resolution mass spectrometer of one of the AMS instruments (HR-AMS) and the measured isotopic ratios unequivocally prove the detection of Pb in ambient particles. A substantial fraction of the lead evaporated slowly from the vaporizer of the instruments, which is indicative of species with low volatility at 600 °C. A model was developed in order to estimate the ambient particulate Pb entering the AMS from the signals in the "open" and the "closed" (or "background") mass spectrum modes of the AMS. The model suggests the presence of at least two lead fractions with ~25% of the Pb signal exhibiting rapid evaporation (1/e decay constant, τ<0.1 s) and ~75% exhibiting slow evaporation (τ~2.4 min) at the T0 urban supersite and a different fraction (70% prompt and 30% slow evaporation) at a site northwest from the metropolitan area (PEMEX site). From laboratory experiments with pure Pb(NO3)2 particles, we estimated that the Pb ionization efficiency relative to nitrate (RIEPb) is 0.5. Comparison of time series of AMS Pb with other measurements carried out at the T0 supersite during MILAGRO (using Proton Induced X-ray Emission (PIXE), Inductively-Coupled Plasma Mass Spectrometry (ICP-MS) and single-particle counts from an Aerosol Time-of-Fight Mass Spectrometer (ATOFMS)) shows similar levels (for PIXE and ICP-MS) and substantial correlation. During part of the campaign, sampling at T0 was alternated every 10 min with an Aerosol Concentrator, which enabled the detection of signals for PbCl+ and PbS+ ions. PbS+ displays the signature of a slowly evaporating species, while PbCl+ appears to arise only from fast evaporation, which is likely due to the higher vapor pressure of the

Octanol-solubility of dissolved and particulate trace metals in contaminated rivers: implications for metal reactivity and availability.

PubMed

Turner, Andrew; Mawji, Edward

2005-05-01

The lipid-like, amphiphilic solvent, n-octanol, has been used to determine a hydrophobic fraction of dissolved and particulate trace metals (Al, Cd, Co, Cu, Mn, Ni, Pb, Zn) in contaminated rivers. In a sample from the River Clyde, southwest Scotland, octanol-solubility was detected for all dissolved metals except Co, with conditional octanol-water partition coefficients, D(ow), ranging from about 0.2 (Al and Cu) to 1.25 (Pb). In a sample taken from the River Mersey, northwest England, octanol-solubility was detected for dissolved Al and Pb, but only after sample aliquots had been spiked with individual ionic metal standards and equilibrated. Spiking of the River Clyde sample revealed competition among different metals for hydrophobic ligands. Metal displacement from hydrophobic complexes was generally most significant following the addition of ionic Al or Pb, although the addition of either of these metals had little effect on the octanol-solubility of the other. In both river water samples hydrophobic metals were detected on the suspended particles retained by filtration following their extraction in n-octanol. In general, particulate Cu and Zn (up to 40%) were most available, and Al, Co and Pb most resistant (<1%) to octanol extraction. Distribution coefficients defining the concentration ratio of octanol-soluble particle-bound metal to octanol-soluble dissolved metal were in the range 10(3.3)-10(5.3)mlg(-1). The presence of hydrophobic dissolved and particulate metal species has implications for our understanding of the biogeochemical behaviour of metals in aquatic environments. Specifically, such species are predicted to exhibit characteristics of non-polar organic contaminants, including the potential to penetrate the lipid bilayer. Current strategies for assessing the bioavailability and toxicity of dissolved and particulate trace metals in natural waters may, therefore, require revision.

40 CFR 52.776 - Control strategy: Particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 3 2014-07-01 2014-07-01 false Control strategy: Particulate matter...: Particulate matter. (a) The requirements of subpart G of this chapter are not met since the plan does not provide for attainment and maintenance of the secondary standards for particulate matter in the...

40 CFR 52.2584 - Control strategy; Particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 4 2011-07-01 2011-07-01 false Control strategy; Particulate matter... Control strategy; Particulate matter. (a) Part D—Disapproval—USEPA disapproves Regulation NR 154.11(7)(b... control strategy to attain and maintain the standards for particulate matter, because it does not contain...

40 CFR 60.532 - Standards for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standards for particulate matter. 60... Wood Heaters § 60.532 Standards for particulate matter. Unless exempted under § 60.530, each affected..., 1992, shall comply with the following particulate matter emission limits as determined by the test...

40 CFR 52.2584 - Control strategy; Particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 5 2014-07-01 2014-07-01 false Control strategy; Particulate matter... Control strategy; Particulate matter. (a) Part D—Disapproval—USEPA disapproves Regulation NR 154.11(7)(b... control strategy to attain and maintain the standards for particulate matter, because it does not contain...

40 CFR 60.162 - Standard for particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Standard for particulate matter. 60.162... Smelters § 60.162 Standard for particulate matter. (a) On and after the date on which the performance test... particulate matter in excess of 50 mg/dscm (0.022 gr/dscf). ...

40 CFR 52.776 - Control strategy: Particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 3 2012-07-01 2012-07-01 false Control strategy: Particulate matter...: Particulate matter. (a) The requirements of subpart G of this chapter are not met since the plan does not provide for attainment and maintenance of the secondary standards for particulate matter in the...

40 CFR 60.162 - Standard for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standard for particulate matter. 60.162... Smelters § 60.162 Standard for particulate matter. (a) On and after the date on which the performance test... particulate matter in excess of 50 mg/dscm (0.022 gr/dscf). ...

40 CFR 60.532 - Standards for particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standards for particulate matter. 60... Wood Heaters § 60.532 Standards for particulate matter. Unless exempted under § 60.530, each affected..., 1992, shall comply with the following particulate matter emission limits as determined by the test...

40 CFR 52.2584 - Control strategy; Particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 5 2013-07-01 2013-07-01 false Control strategy; Particulate matter... Control strategy; Particulate matter. (a) Part D—Disapproval—USEPA disapproves Regulation NR 154.11(7)(b... control strategy to attain and maintain the standards for particulate matter, because it does not contain...

40 CFR 52.2584 - Control strategy; Particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 5 2012-07-01 2012-07-01 false Control strategy; Particulate matter... Control strategy; Particulate matter. (a) Part D—Disapproval—USEPA disapproves Regulation NR 154.11(7)(b... control strategy to attain and maintain the standards for particulate matter, because it does not contain...

40 CFR 52.2584 - Control strategy; Particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control strategy; Particulate matter... Control strategy; Particulate matter. (a) Part D—Disapproval—USEPA disapproves Regulation NR 154.11(7)(b... control strategy to attain and maintain the standards for particulate matter, because it does not contain...

40 CFR 60.162 - Standard for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standard for particulate matter. 60.162... Smelters § 60.162 Standard for particulate matter. (a) On and after the date on which the performance test... particulate matter in excess of 50 mg/dscm (0.022 gr/dscf). ...

40 CFR 60.162 - Standard for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standard for particulate matter. 60.162... Smelters § 60.162 Standard for particulate matter. (a) On and after the date on which the performance test... particulate matter in excess of 50 mg/dscm (0.022 gr/dscf). ...

40 CFR 60.162 - Standard for particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for particulate matter. 60.162... Smelters § 60.162 Standard for particulate matter. (a) On and after the date on which the performance test... particulate matter in excess of 50 mg/dscm (0.022 gr/dscf). ...

40 CFR 60.532 - Standards for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standards for particulate matter. 60... Wood Heaters § 60.532 Standards for particulate matter. Unless exempted under § 60.530, each affected..., 1992, shall comply with the following particulate matter emission limits as determined by the test...

40 CFR 60.532 - Standards for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standards for particulate matter. 60... Wood Heaters § 60.532 Standards for particulate matter. Unless exempted under § 60.530, each affected..., 1992, shall comply with the following particulate matter emission limits as determined by the test...

40 CFR 52.1476 - Control strategy: Particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... National Ambient Air Quality Standards for particulate matter. (1) NAQR Article 7.2.7, Particulate Matter; Table 4.2, Emissions Inventory Summary for Particulates and Table 5.2, Summary of Control Strategy... 24, 1979. (2) Nevada Air Quality Regulations, Article 4, Rule 4.34, (Visible Emission from Stationary...

Electrically heated particulate filter regeneration using hydrocarbon adsorbents

DOEpatents

Gonze, Eugene V [Pinckney, MI; Ament, Frank [Troy, MI

2011-02-01

An exhaust system that processes exhaust generated by an engine is provided. The system generally includes a particulate filter (PF) that filters particulates from the exhaust wherein an upstream end of the PF receives exhaust from the engine. A grid of electrically resistive material selectively heats exhaust passing through the upstream end to initiate combustion of particulates within the PF. A hydrocarbon adsorbent coating applied to the PF releases hydrocarbons into the exhaust to increase a temperature of the combustion of the particulates within the PF.

40 CFR 52.1476 - Control strategy: Particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 4 2014-07-01 2014-07-01 false Control strategy: Particulate matter... strategy: Particulate matter. (a) The requirements of subpart G of this chapter are not met since the plan does not provide for the attainment and maintenance of the national standards for particulate matter in...

40 CFR 60.172 - Standard for particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Standard for particulate matter. 60.172... Smelters § 60.172 Standard for particulate matter. (a) On and after the date on which the performance test... contain particulate matter in excess of 50 mg/dscm (0.022 gr/dscf). ...

40 CFR 60.172 - Standard for particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for particulate matter. 60.172... Smelters § 60.172 Standard for particulate matter. (a) On and after the date on which the performance test... contain particulate matter in excess of 50 mg/dscm (0.022 gr/dscf). ...

40 CFR 52.1476 - Control strategy: Particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 4 2011-07-01 2011-07-01 false Control strategy: Particulate matter... strategy: Particulate matter. (a) The requirements of subpart G of this chapter are not met since the plan does not provide for the attainment and maintenance of the national standards for particulate matter in...

40 CFR 60.172 - Standard for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standard for particulate matter. 60.172... Smelters § 60.172 Standard for particulate matter. (a) On and after the date on which the performance test... contain particulate matter in excess of 50 mg/dscm (0.022 gr/dscf). ...

40 CFR 52.1476 - Control strategy: Particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 4 2013-07-01 2013-07-01 false Control strategy: Particulate matter... strategy: Particulate matter. (a) The requirements of subpart G of this chapter are not met since the plan does not provide for the attainment and maintenance of the national standards for particulate matter in...

40 CFR 60.172 - Standard for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standard for particulate matter. 60.172... Smelters § 60.172 Standard for particulate matter. (a) On and after the date on which the performance test... contain particulate matter in excess of 50 mg/dscm (0.022 gr/dscf). ...

40 CFR 52.2059 - Control strategy: Particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 5 2014-07-01 2014-07-01 false Control strategy: Particulate matter... Control strategy: Particulate matter. (a) [Reserved] (b) EPA approves the PM-10 attainment demonstration...-Wilmington, PA-NJ-DE fine particulate matter (PM2.5) nonattainment area has attained the 2006 24-hour PM2.5...

40 CFR 60.172 - Standard for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standard for particulate matter. 60.172... Smelters § 60.172 Standard for particulate matter. (a) On and after the date on which the performance test... contain particulate matter in excess of 50 mg/dscm (0.022 gr/dscf). ...

40 CFR 52.1476 - Control strategy: Particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 4 2012-07-01 2012-07-01 false Control strategy: Particulate matter... strategy: Particulate matter. (a) The requirements of subpart G of this chapter are not met since the plan does not provide for the attainment and maintenance of the national standards for particulate matter in...

Diesel particulate filter with zoned resistive heater

DOEpatents

Gonze, Eugene V [Pinckney, MI

2011-03-08

A diesel particulate filter assembly comprises a diesel particulate filter (DPF) and a heater assembly. The DPF filters a particulate from exhaust produced by an engine. The heater assembly has a first metallic layer that is applied to the DPF, a resistive layer that is applied to the first metallic layer, and a second metallic layer that is applied to the resistive layer. The second metallic layer is etched to form a plurality of zones.

Les effets des interfaces sur les proprietes magnetiques et de transport des multicouches nickel/iron et cobalt/silver

NASA Astrophysics Data System (ADS)

Veres, Teodor

Cette these est consacree a l'etude de l'evolution structurale des proprietes magnetiques et de transport des multicouches Ni/Fe et nanostructures a base de Co et de l'Ag. Dans une premiere partie, essentiellement bibliographique, nous introduisons quelques concepts de base relies aux proprietes magnetiques et de transport des multicouches metalliques. Ensuite, nous presentons une breve description des methodes d'analyse des resultats. La deuxieme partie est consacree a l'etude des proprietes magnetiques et de transport des multicouches ferromagnetiques/ferromagnetiques Ni/Fe. Nous montrerons qu'une interpretation coherente de ces proprietes necessite la prise en consideration des effets des interfaces. Nous nous attacherons a mettre en evidence, a evaluer et a etudier les effets de ces interfaces ainsi que leur evolution, et ce, suite a des traitements thermiques tel que le depot a temperature elevee et l'irradiation ionique. Les analyses correlees de la structure et de la magnetoresistance nous permettront d'emettre des conclusions sur l'influence des couches tampons entre l'interface et le substrat ainsi qu'entre les couches elles-memes sur le comportement magnetique des couches F/F. La troisieme partie est consacree aux systemes a Magneto-Resistance Geante (MRG) a base de Co et Ag. Nous allons etudier l'evolution de la microstructure suite a l'irradiation avec des ions Si+ ayant une energie de 1 MeV, ainsi que les effets de ces changements sur le comportement magnetique. Cette partie debutera par l'analyse des proprietes d'une multicouche hybride, intermediaire entre les multicouches et les materiaux granulaires. Nous analyserons a l'aide des mesures de diffraction, de relaxation superparamagnetique et de magnetoresistance, les evolutions structurales produites par l'irradiation ionique. Nous etablirons des modeles qui nous aideront a interpreter les resultats pour une serie des multicouches qui couvrent un large eventail de differents comportements magnetiques

Caracterisation des proprietes acoustiques des materiaux poreux a cellules ouvertes et a matrice rigide ou souple

NASA Astrophysics Data System (ADS)

Salissou, Yacoubou

L'objectif global vise par les travaux de cette these est d'ameliorer la caracterisation des proprietes macroscopiques des materiaux poreux a structure rigide ou souple par des approches inverses et indirectes basees sur des mesures acoustiques faites en tube d'impedance. La precision des approches inverses et indirectes utilisees aujourd'hui est principalement limitee par la qualite des mesures acoustiques obtenues en tube d'impedance. En consequence, cette these se penche sur quatre problemes qui aideront a l'atteinte de l'objectif global precite. Le premier probleme porte sur une caracterisation precise de la porosite ouverte des materiaux poreux. Cette propriete en est une de passage permettant de lier la mesure des proprietes dynamiques acoustiques d'un materiau poreux aux proprietes effectives de sa phase fluide decrite par les modeles semi-phenomenologiques. Le deuxieme probleme traite de l'hypothese de symetrie des materiaux poreux selon leur epaisseur ou un index et un critere sont proposes pour quantifier l'asymetrie d'un materiau. Cette hypothese est souvent source d'imprecision des methodes de caracterisation inverses et indirectes en tube d'impedance. Le critere d'asymetrie propose permet ainsi de s'assurer de l'applicabilite et de la precision de ces methodes pour un materiau donne. Le troisieme probleme vise a mieux comprendre le probleme de transmission sonore en tube d'impedance en presentant pour la premiere fois un developpement exact du probleme par decomposition d'ondes. Ce developpement permet d'etablir clairement les limites des nombreuses methodes existantes basees sur des tubes de transmission a 2, 3 ou 4 microphones. La meilleure comprehension de ce probleme de transmission est importante puisque c'est par ce type de mesures que des methodes permettent d'extraire successivement la matrice de transfert d'un materiau poreux et ses proprietes dynamiques intrinseques comme son impedance caracteristique et son nombre d'onde complexe. Enfin, le

Method for immobilizing particulate materials in a packed bed

DOEpatents

Even, W.R. Jr.; Guthrie, S.E.; Raber, T.N.; Wally, K.; Whinnery, L.L.; Zifer, T.

1999-02-02

The present invention pertains generally to immobilizing particulate matter contained in a packed bed reactor so as to prevent powder migration, compaction, coalescence, or the like. More specifically, this invention relates to a technique for immobilizing particulate materials using a microporous foam-like polymer such that (a) the particulate retains its essential chemical nature, (b) the local movement of the particulate particles is not unduly restricted, (c) bulk powder migration and is prevented, (d) physical and chemical access to the particulate is unchanged over time, and (e) very high particulate densities are achieved. The immobilized bed of the present invention comprises a vessel for holding particulate matter, inlet and an outlet ports or fittings, a loosely packed bed of particulate material contained within the vessel, and a three dimensional porous matrix for surrounding and confining the particles thereby fixing the movement of an individual particle to a limited local position. The established matrix is composed of a series of cells or chambers comprising walls surrounding void space, each wall forming the wall of an adjacent cell; each wall containing many holes penetrating through the wall yielding an overall porous structure and allowing useful levels of gas transport. 4 figs.

Method for immobilizing particulate materials in a packed bed

DOEpatents

Even, Jr., William R.; Guthrie, Stephen E.; Raber, Thomas N.; Wally, Karl; Whinnery, LeRoy L.; Zifer, Thomas

1999-01-01

The present invention pertains generally to immobilizing particulate matter contained in a "packed" bed reactor so as to prevent powder migration, compaction, coalescence, or the like. More specifically, this invention relates to a technique for immobilizing particulate materials using a microporous foam-like polymer such that a) the particulate retains its essential chemical nature, b) the local movement of the particulate particles is not unduly restricted, c) bulk powder migration and is prevented, d) physical and chemical access to the particulate is unchanged over time, and e) very high particulate densities are achieved. The immobilized bed of the present invention comprises a vessel for holding particulate matter, inlet and an outlet ports or fittings, a loosely packed bed of particulate material contained within the vessel, and a three dimensional porous matrix for surrounding and confining the particles thereby fixing the movement of individual particle to a limited local position. The established matrix is composed of a series of cells or chambers comprising walls surrounding void space, each wall forming the wall of an adjacent cell; each wall containing many holes penetrating through the wall yielding an overall porous structure and allowing useful levels of gas transport.

40 CFR 230.21 - Suspended particulates/turbidity.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Impacts on Physical and Chemical Characteristics of the Aquatic Ecosystem § 230.21 Suspended particulates/turbidity. (a) Suspended particulates in the aquatic ecosystem consist of fine-grained mineral particles...

40 CFR 230.21 - Suspended particulates/turbidity.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Impacts on Physical and Chemical Characteristics of the Aquatic Ecosystem § 230.21 Suspended particulates/turbidity. (a) Suspended particulates in the aquatic ecosystem consist of fine-grained mineral particles...

40 CFR 230.21 - Suspended particulates/turbidity.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Impacts on Physical and Chemical Characteristics of the Aquatic Ecosystem § 230.21 Suspended particulates/turbidity. (a) Suspended particulates in the aquatic ecosystem consist of fine-grained mineral particles...

40 CFR 230.21 - Suspended particulates/turbidity.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Impacts on Physical and Chemical Characteristics of the Aquatic Ecosystem § 230.21 Suspended particulates/turbidity. (a) Suspended particulates in the aquatic ecosystem consist of fine-grained mineral particles...

40 CFR 230.21 - Suspended particulates/turbidity.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Impacts on Physical and Chemical Characteristics of the Aquatic Ecosystem § 230.21 Suspended particulates/turbidity. (a) Suspended particulates in the aquatic ecosystem consist of fine-grained mineral particles...

40 CFR 60.292 - Standards for particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Standards for particulate matter. 60... Manufacturing Plants § 60.292 Standards for particulate matter. (a) On and after the date on which the..., particulate matter at emission rates exceeding those specified in table CC-1, Column 2 and Column 3...

40 CFR 60.292 - Standards for particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standards for particulate matter. 60... Manufacturing Plants § 60.292 Standards for particulate matter. (a) On and after the date on which the..., particulate matter at emission rates exceeding those specified in table CC-1, Column 2 and Column 3...

40 CFR 60.382 - Standard for particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for particulate matter. 60.382... Processing Plants § 60.382 Standard for particulate matter. (a) On and after the date on which the... stack emissions that: (1) Contain particulate matter in excess of 0.05 grams per dry standard cubic...

40 CFR 52.427 - Control strategy: Particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 3 2013-07-01 2013-07-01 false Control strategy: Particulate matter...: Particulate matter. (a) Determination of attainment. EPA has determined, as of May 16, 2012, that based on... fine particulate matter (PM2.5) nonattainment area has attained the 2006 24-hour PM2.5 national ambient...

40 CFR 60.382 - Standard for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standard for particulate matter. 60.382... Processing Plants § 60.382 Standard for particulate matter. (a) On and after the date on which the... stack emissions that: (1) Contain particulate matter in excess of 0.05 grams per dry standard cubic...

40 CFR 60.292 - Standards for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standards for particulate matter. 60... Manufacturing Plants § 60.292 Standards for particulate matter. (a) On and after the date on which the..., particulate matter at emission rates exceeding those specified in table CC-1, Column 2 and Column 3...

40 CFR 60.382 - Standard for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standard for particulate matter. 60.382... Processing Plants § 60.382 Standard for particulate matter. (a) On and after the date on which the... stack emissions that: (1) Contain particulate matter in excess of 0.05 grams per dry standard cubic...

40 CFR 52.427 - Control strategy: Particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 3 2014-07-01 2014-07-01 false Control strategy: Particulate matter...: Particulate matter. (a) Determination of attainment. EPA has determined, as of May 16, 2012, that based on... fine particulate matter (PM2.5) nonattainment area has attained the 2006 24-hour PM2.5 national ambient...

40 CFR 60.292 - Standards for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standards for particulate matter. 60... Manufacturing Plants § 60.292 Standards for particulate matter. (a) On and after the date on which the..., particulate matter at emission rates exceeding those specified in table CC-1, Column 2 and Column 3...

40 CFR 60.292 - Standards for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standards for particulate matter. 60... Manufacturing Plants § 60.292 Standards for particulate matter. (a) On and after the date on which the..., particulate matter at emission rates exceeding those specified in table CC-1, Column 2 and Column 3...

40 CFR 60.382 - Standard for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standard for particulate matter. 60.382... Processing Plants § 60.382 Standard for particulate matter. (a) On and after the date on which the... stack emissions that: (1) Contain particulate matter in excess of 0.05 grams per dry standard cubic...

40 CFR 60.732 - Standards for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standards for particulate matter. 60... Dryers in Mineral Industries § 60.732 Standards for particulate matter. Each owner or operator of any... particulate matter in excess of 0.092 gram per dry standard cubic meter (g/dscm) [0.040 grain per dry standard...

40 CFR 60.182 - Standard for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standard for particulate matter. 60.182... Smelters § 60.182 Standard for particulate matter. (a) On and after the date on which the performance test... furnace, or sintering machine discharge end any gases which contain particulate matter in excess of 50 mg...

40 CFR 60.132 - Standard for particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Standard for particulate matter. 60.132... and Bronze Production Plants § 60.132 Standard for particulate matter. (a) On and after the date on... reverberatory furnace any gases which: (1) Contain particulate matter in excess of 50 mg/dscm (0.022 gr/dscf...

40 CFR 60.262 - Standard for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standard for particulate matter. 60.262... Production Facilities § 60.262 Standard for particulate matter. (a) On and after the date on which the... furnace any gases which: (1) Exit from a control device and contain particulate matter in excess of 0.45...

40 CFR 60.342 - Standard for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standard for particulate matter. 60.342... Manufacturing Plants § 60.342 Standard for particulate matter. (a) On and after the date on which the... gases which: (1) Contain particulate matter in excess of 0.30 kilogram per megagram (0.60 lb/ton) of...

40 CFR 60.732 - Standards for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standards for particulate matter. 60... Dryers in Mineral Industries § 60.732 Standards for particulate matter. Each owner or operator of any... particulate matter in excess of 0.092 gram per dry standard cubic meter (g/dscm) [0.040 grain per dry standard...

40 CFR 60.132 - Standard for particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for particulate matter. 60.132... and Bronze Production Plants § 60.132 Standard for particulate matter. (a) On and after the date on... reverberatory furnace any gases which: (1) Contain particulate matter in excess of 50 mg/dscm (0.022 gr/dscf...

40 CFR 60.472 - Standards for particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standards for particulate matter. 60... Processing and Asphalt Roofing Manufacture § 60.472 Standards for particulate matter. (a) On and after the...) Particulate matter in excess of: (i) 0.04 kg/Mg (0.08 lb/ton) of asphalt shingle or mineral-surfaced roll...

40 CFR 60.262 - Standard for particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Standard for particulate matter. 60.262... Production Facilities § 60.262 Standard for particulate matter. (a) On and after the date on which the... furnace any gases which: (1) Exit from a control device and contain particulate matter in excess of 0.45...

40 CFR 60.52 - Standard for particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Standard for particulate matter. 60.52... § 60.52 Standard for particulate matter. (a) On and after the date on which the initial performance... atmosphere from any affected facility any gases which contain particulate matter in excess of 0.18 g/dscm (0...

40 CFR 60.182 - Standard for particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for particulate matter. 60.182... Smelters § 60.182 Standard for particulate matter. (a) On and after the date on which the performance test... furnace, or sintering machine discharge end any gases which contain particulate matter in excess of 50 mg...

40 CFR 60.302 - Standard for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standard for particulate matter. 60.302... § 60.302 Standard for particulate matter. (a) On and after the 60th day of achieving the maximum... a grain dryer any process emission which: (1) Contains particulate matter in excess of 0.023 g/dscm...

40 CFR 60.732 - Standards for particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standards for particulate matter. 60... Dryers in Mineral Industries § 60.732 Standards for particulate matter. Each owner or operator of any... particulate matter in excess of 0.092 gram per dry standard cubic meter (g/dscm) [0.040 grain per dry standard...

40 CFR 60.52 - Standard for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standard for particulate matter. 60.52... § 60.52 Standard for particulate matter. (a) On and after the date on which the initial performance... atmosphere from any affected facility any gases which contain particulate matter in excess of 0.18 g/dscm (0...

40 CFR 60.302 - Standard for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standard for particulate matter. 60.302... § 60.302 Standard for particulate matter. (a) On and after the 60th day of achieving the maximum... a grain dryer any process emission which: (1) Contains particulate matter in excess of 0.023 g/dscm...

40 CFR 60.342 - Standard for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standard for particulate matter. 60.342... Manufacturing Plants § 60.342 Standard for particulate matter. (a) On and after the date on which the... gases which: (1) Contain particulate matter in excess of 0.30 kilogram per megagram (0.60 lb/ton) of...

40 CFR 60.132 - Standard for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standard for particulate matter. 60.132... and Bronze Production Plants § 60.132 Standard for particulate matter. (a) On and after the date on... reverberatory furnace any gases which: (1) Contain particulate matter in excess of 50 mg/dscm (0.022 gr/dscf...

40 CFR 60.472 - Standards for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standards for particulate matter. 60... Processing and Asphalt Roofing Manufacture § 60.472 Standards for particulate matter. (a) On and after the...) Particulate matter in excess of: (i) 0.04 kg/Mg (0.08 lb/ton) of asphalt shingle or mineral-surfaced roll...

40 CFR 60.302 - Standard for particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Standard for particulate matter. 60.302... § 60.302 Standard for particulate matter. (a) On and after the 60th day of achieving the maximum... a grain dryer any process emission which: (1) Contains particulate matter in excess of 0.023 g/dscm...

40 CFR 60.52 - Standard for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standard for particulate matter. 60.52... § 60.52 Standard for particulate matter. (a) On and after the date on which the initial performance... atmosphere from any affected facility any gases which contain particulate matter in excess of 0.18 g/dscm (0...

40 CFR 60.472 - Standards for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standards for particulate matter. 60... Processing and Asphalt Roofing Manufacture § 60.472 Standards for particulate matter. (a) On and after the...) Particulate matter in excess of: (i) 0.04 kg/Mg (0.08 lb/ton) of asphalt shingle or mineral-surfaced roll...

40 CFR 60.182 - Standard for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standard for particulate matter. 60.182... Smelters § 60.182 Standard for particulate matter. (a) On and after the date on which the performance test... furnace, or sintering machine discharge end any gases which contain particulate matter in excess of 50 mg...

40 CFR 60.302 - Standard for particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for particulate matter. 60.302... § 60.302 Standard for particulate matter. (a) On and after the 60th day of achieving the maximum... a grain dryer any process emission which: (1) Contains particulate matter in excess of 0.023 g/dscm...

40 CFR 60.52 - Standard for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standard for particulate matter. 60.52... § 60.52 Standard for particulate matter. (a) On and after the date on which the initial performance... atmosphere from any affected facility any gases which contain particulate matter in excess of 0.18 g/dscm (0...

40 CFR 60.52 - Standard for particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for particulate matter. 60.52... § 60.52 Standard for particulate matter. (a) On and after the date on which the initial performance... atmosphere from any affected facility any gases which contain particulate matter in excess of 0.18 g/dscm (0...

40 CFR 60.132 - Standard for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standard for particulate matter. 60.132... and Bronze Production Plants § 60.132 Standard for particulate matter. (a) On and after the date on... reverberatory furnace any gases which: (1) Contain particulate matter in excess of 50 mg/dscm (0.022 gr/dscf...

40 CFR 60.262 - Standard for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standard for particulate matter. 60.262... Production Facilities § 60.262 Standard for particulate matter. (a) On and after the date on which the... furnace any gases which: (1) Exit from a control device and contain particulate matter in excess of 0.45...

40 CFR 60.732 - Standards for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standards for particulate matter. 60... Dryers in Mineral Industries § 60.732 Standards for particulate matter. Each owner or operator of any... particulate matter in excess of 0.092 gram per dry standard cubic meter (g/dscm) [0.040 grain per dry standard...

40 CFR 60.182 - Standard for particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Standard for particulate matter. 60.182... Smelters § 60.182 Standard for particulate matter. (a) On and after the date on which the performance test... furnace, or sintering machine discharge end any gases which contain particulate matter in excess of 50 mg...

40 CFR 60.132 - Standard for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standard for particulate matter. 60.132... and Bronze Production Plants § 60.132 Standard for particulate matter. (a) On and after the date on... reverberatory furnace any gases which: (1) Contain particulate matter in excess of 50 mg/dscm (0.022 gr/dscf...

40 CFR 60.342 - Standard for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standard for particulate matter. 60.342... Manufacturing Plants § 60.342 Standard for particulate matter. (a) On and after the date on which the... gases which: (1) Contain particulate matter in excess of 0.30 kilogram per megagram (0.60 lb/ton) of...

40 CFR 60.302 - Standard for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standard for particulate matter. 60.302... § 60.302 Standard for particulate matter. (a) On and after the 60th day of achieving the maximum... a grain dryer any process emission which: (1) Contains particulate matter in excess of 0.023 g/dscm...

40 CFR 60.182 - Standard for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standard for particulate matter. 60.182... Smelters § 60.182 Standard for particulate matter. (a) On and after the date on which the performance test... furnace, or sintering machine discharge end any gases which contain particulate matter in excess of 50 mg...

40 CFR 60.472 - Standards for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standards for particulate matter. 60... Processing and Asphalt Roofing Manufacture § 60.472 Standards for particulate matter. (a) On and after the...) Particulate matter in excess of: (i) 0.04 kg/Mg (0.08 lb/ton) of asphalt shingle or mineral-surfaced roll...

40 CFR 60.262 - Standard for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standard for particulate matter. 60.262... Production Facilities § 60.262 Standard for particulate matter. (a) On and after the date on which the... furnace any gases which: (1) Exit from a control device and contain particulate matter in excess of 0.45...

Electrically heated particulate filter preparation methods and systems

DOEpatents

Gonze, Eugene V [Pinckney, MI

2012-01-31

A control system that controls regeneration of a particulate filter is provided. The system generally includes a fuel control module that controls injection of fuel into exhaust that passes through the particulate filter. A regeneration module controls current to the particulate filter to initiate regeneration after the fuel has been injected into the exhaust.

Hydrophilic Interaction Liquid Chromatography-Tandem Mass Spectrometry Analysis of Fosetyl-Aluminum in Airborne Particulate Matter

PubMed Central

Di Filippo, Patrizia; Riccardi, Carmela; Pomata, Donatella; Marsiglia, Riccardo; Console, Carla; Puri, Daniele

2018-01-01

Fosetyl-aluminum is a synthetic fungicide administered to plants especially to prevent diseases caused by the members of the Peronosporales and several Phytophthora species. Herein, we present a selective liquid chromatography-tandem mass spectrometry (LC-MS/MS) method to analyze residues of fosetyl-A1 in air particulate matter. This study was performed in perspective of an exposure assessment of this substance of health concern in environments where high levels of fosetly-Al, relatively to airborne particulate matter, can be found after spraying it. The cleanup procedure of the analyte, from sampled filters of atmospheric particulate matter, was optimized using a Strata X solid-phase extraction cartridge, after accelerated extraction by using water. The chromatographic separation was achieved using a polymeric column based on hydrophilic interaction in step elution with water/acetonitrile, whereas the mass spectrometric detection was performed in negative electrospray ionization. The proposed method resulted to be a simple, fast, and suitable method for confirmation purposes. PMID:29686933

Fluctuations Magnetiques des Gaz D'electrons Bidimensionnels: Application AU Compose Supraconducteur LANTHANE(2-X) Strontium(x) Cuivre OXYGENE(4)

NASA Astrophysics Data System (ADS)

Benard, Pierre

Nous presentons une etude des fluctuations magnetiques de la phase normale de l'oxyde de cuivre supraconducteur La_{2-x}Sr _{x}CuO_4 . Le compose est modelise par le Hamiltonien de Hubbard bidimensionnel avec un terme de saut vers les deuxiemes voisins (modele tt'U). Le modele est etudie en utilisant l'approximation de la GRPA (Generalized Random Phase Approximation) et en incluant les effets de la renormalisation de l'interaction de Hubbard par les diagrammes de Brueckner-Kanamori. Dans l'approche presentee dans ce travail, les maximums du facteur de structure magnetique observes par les experiences de diffusion de neutrons sont associes aux anomalies 2k _{F} de reseau du facteur de structure des gaz d'electrons bidimensionnels sans interaction. Ces anomalies proviennent de la diffusion entre particules situees a des points de la surface de Fermi ou les vitesses de Fermi sont tangentes, et conduisent a des divergences dont la nature depend de la geometrie de la surface de Fermi au voisinage de ces points. Ces resultats sont ensuite appliques au modele tt'U, dont le modele de Hubbard usuel tU est un cas particulier. Dans la majorite des cas, les interactions ne determinent pas la position des maximums du facteur de structure. Le role de l'interaction est d'augmenter l'intensite des structures du facteur de structure magnetique associees a l'instabilite magnetique du systeme. Ces structures sont souvent deja presentes dans la partie imaginaire de la susceptibilite sans interaction. Le rapport d'intensite entre les maximums absolus et les autres structures du facteur de structure magnetique permet de determiner le rapport U_ {rn}/U_{c} qui mesure la proximite d'une instabilite magnetique. Le diagramme de phase est ensuite etudie afin de delimiter la plage de validite de l'approximation. Apres avoir discute des modes collectifs et de l'effet d'une partie imaginaire non-nulle de la self-energie, l'origine de l'echelle d'energie des fluctuations magnetiques est examinee

Apparatus and method for rapid detection of explosives residue from the deflagration signature thereof

DOEpatents

Funsten, H.O.; McComas, D.J.

1999-06-15

Apparatus and method are disclosed for rapid detection of explosives residue from the deflagration signature thereof. A property inherent to most explosives is their stickiness, resulting in a strong tendency of explosive particulate to contaminate the environment of a bulk explosive. An apparatus for collection of residue particulate, burning the collected particulate, and measurement of the ultraviolet emission produced thereby, is described. The present invention can be utilized for real-time screening of personnel, cars, packages, suspected devices, etc., and provides an inexpensive, portable, and noninvasive means for detecting explosives. 4 figs.

Apparatus and method for rapid detection of explosives residue from the deflagration signature thereof

DOEpatents

Funsten, Herbert O.; McComas, David J.

1997-01-01

Apparatus and method for rapid detection of explosives residue from the deflagration signature thereof. A property inherent to most explosives is their stickiness, resulting in a strong tendency of explosive particulate to contaminate the environment of a bulk explosive. An apparatus for collection of residue particulate, burning the collected particulate, and measurement of the optical emission produced thereby is described. The present invention can be utilized for real-time screening of personnel, cars, packages, suspected devices, etc., and provides an inexpensive, portable, and noninvasive means for detecting explosives.

Apparatus and method for rapid detection of explosives residue from the deflagration signature thereof

DOEpatents

Funsten, Herbert O.; McComas, David J.

1999-01-01

Apparatus and method for rapid detection of explosives residue from the deflagration signature thereof. A property inherent to most explosives is their stickiness, resulting in a strong tendency of explosive particulate to contaminate the environment of a bulk explosive. An apparatus for collection of residue particulate, burning the collected particulate, and measurement of the ultraviolet emission produced thereby, is described. The present invention can be utilized for real-time screening of personnel, cars, packages, suspected devices, etc., and provides an inexpensive, portable, and noninvasive means for detecting explosives.

40 CFR 60.682 - Standard for particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Standard for particulate matter. 60.682... Insulation Manufacturing Plants § 60.682 Standard for particulate matter. On and after the date on which the... gases which contain particulate matter in excess of 5.5 kg/Mg (11.0 1b/ton) of glass pulled. ...

40 CFR 60.682 - Standard for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standard for particulate matter. 60.682... Insulation Manufacturing Plants § 60.682 Standard for particulate matter. On and after the date on which the... gases which contain particulate matter in excess of 5.5 kg/Mg (11.0 1b/ton) of glass pulled. ...

40 CFR 60.122 - Standard for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standard for particulate matter. 60.122... Smelters § 60.122 Standard for particulate matter. (a) On and after the date on which the performance test... furnace any gases which: (1) Contain particulate matter in excess of 50 mg/dscm (0.022 gr/dscf). (2...

40 CFR 60.92 - Standard for particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for particulate matter. 60.92... Facilities § 60.92 Standard for particulate matter. (a) On and after the date on which the performance test... which: (1) Contain particulate matter in excess of 90 mg/dscm (0.04 gr/dscf). (2) Exhibit 20 percent...

40 CFR 60.92 - Standard for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standard for particulate matter. 60.92... Facilities § 60.92 Standard for particulate matter. (a) On and after the date on which the performance test... which: (1) Contain particulate matter in excess of 90 mg/dscm (0.04 gr/dscf). (2) Exhibit 20 percent...

40 CFR 60.122 - Standard for particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Standard for particulate matter. 60.122... Smelters § 60.122 Standard for particulate matter. (a) On and after the date on which the performance test... furnace any gases which: (1) Contain particulate matter in excess of 50 mg/dscm (0.022 gr/dscf). (2...

40 CFR 60.682 - Standard for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standard for particulate matter. 60.682... Insulation Manufacturing Plants § 60.682 Standard for particulate matter. On and after the date on which the... gases which contain particulate matter in excess of 5.5 kg/Mg (11.0 1b/ton) of glass pulled. ...

40 CFR 60.682 - Standard for particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for particulate matter. 60.682... Insulation Manufacturing Plants § 60.682 Standard for particulate matter. On and after the date on which the... gases which contain particulate matter in excess of 5.5 kg/Mg (11.0 1b/ton) of glass pulled. ...

40 CFR 60.272 - Standard for particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Standard for particulate matter. 60.272... Standard for particulate matter. (a) On and after the date on which the performance test required to be... control device and contain particulate matter in excess of 12 mg/dscm (0.0052 gr/dscf). (2) Exit from a...

40 CFR 60.92 - Standard for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standard for particulate matter. 60.92... Facilities § 60.92 Standard for particulate matter. (a) On and after the date on which the performance test... which: (1) Contain particulate matter in excess of 90 mg/dscm (0.04 gr/dscf). (2) Exhibit 20 percent...

40 CFR 60.122 - Standard for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standard for particulate matter. 60.122... Smelters § 60.122 Standard for particulate matter. (a) On and after the date on which the performance test... furnace any gases which: (1) Contain particulate matter in excess of 50 mg/dscm (0.022 gr/dscf). (2...

40 CFR 60.152 - Standard for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standard for particulate matter. 60.152... Plants § 60.152 Standard for particulate matter. (a) On and after the date on which the performance test...: (1) Particulate matter at a rate in excess of 0.65 g/kg dry sludge input (1.30 lb/ton dry sludge...

40 CFR 60.152 - Standard for particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for particulate matter. 60.152... Plants § 60.152 Standard for particulate matter. (a) On and after the date on which the performance test...: (1) Particulate matter at a rate in excess of 0.65 g/kg dry sludge input (1.30 lb/ton dry sludge...

40 CFR 60.92 - Standard for particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Standard for particulate matter. 60.92... Facilities § 60.92 Standard for particulate matter. (a) On and after the date on which the performance test... which: (1) Contain particulate matter in excess of 90 mg/dscm (0.04 gr/dscf). (2) Exhibit 20 percent...

40 CFR 60.122 - Standard for particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for particulate matter. 60.122... Smelters § 60.122 Standard for particulate matter. (a) On and after the date on which the performance test... furnace any gases which: (1) Contain particulate matter in excess of 50 mg/dscm (0.022 gr/dscf). (2...

40 CFR 60.122 - Standard for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standard for particulate matter. 60.122... Smelters § 60.122 Standard for particulate matter. (a) On and after the date on which the performance test... furnace any gases which: (1) Contain particulate matter in excess of 50 mg/dscm (0.022 gr/dscf). (2...

40 CFR 60.272 - Standard for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standard for particulate matter. 60.272... Standard for particulate matter. (a) On and after the date on which the performance test required to be... control device and contain particulate matter in excess of 12 mg/dscm (0.0052 gr/dscf). (2) Exit from a...

40 CFR 60.152 - Standard for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standard for particulate matter. 60.152... Plants § 60.152 Standard for particulate matter. (a) On and after the date on which the performance test...: (1) Particulate matter at a rate in excess of 0.65 g/kg dry sludge input (1.30 lb/ton dry sludge...

40 CFR 60.92 - Standard for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standard for particulate matter. 60.92... Facilities § 60.92 Standard for particulate matter. (a) On and after the date on which the performance test... which: (1) Contain particulate matter in excess of 90 mg/dscm (0.04 gr/dscf). (2) Exhibit 20 percent...

40 CFR 60.152 - Standard for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standard for particulate matter. 60.152... Plants § 60.152 Standard for particulate matter. (a) On and after the date on which the performance test...: (1) Particulate matter at a rate in excess of 0.65 g/kg dry sludge input (1.30 lb/ton dry sludge...

40 CFR 60.682 - Standard for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standard for particulate matter. 60.682... Insulation Manufacturing Plants § 60.682 Standard for particulate matter. On and after the date on which the... gases which contain particulate matter in excess of 5.5 kg/Mg (11.0 1b/ton) of glass pulled. ...

40 CFR 60.272 - Standard for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standard for particulate matter. 60.272... Standard for particulate matter. (a) On and after the date on which the performance test required to be... control device and contain particulate matter in excess of 12 mg/dscm (0.0052 gr/dscf). (2) Exit from a...

40 CFR 60.152 - Standard for particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Standard for particulate matter. 60.152... Plants § 60.152 Standard for particulate matter. (a) On and after the date on which the performance test...: (1) Particulate matter at a rate in excess of 0.65 g/kg dry sludge input (1.30 lb/ton dry sludge...

40 CFR 60.272 - Standard for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standard for particulate matter. 60.272... Standard for particulate matter. (a) On and after the date on which the performance test required to be... control device and contain particulate matter in excess of 12 mg/dscm (0.0052 gr/dscf). (2) Exit from a...

40 CFR 86.145-82 - Calculations; particulate emissions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... final reported test results for the mass particulate (Mp) in grams/mile shall be computed as follows. Mp = 0.43(Mp1 + Mp2)/(Dct + Ds) + 0.57(Mp3 + Mp2)/(Dht = Ds) where: (1) Mp1 = Mass of particulate...) for determination.) (2) Mp2 = Mass of particulate determined from the “stabilized” phase of the cold...

40 CFR 86.145-82 - Calculations; particulate emissions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... final reported test results for the mass particulate (Mp) in grams/mile shall be computed as follows. Mp = 0.43(Mp1 + Mp2)/(Dct + Ds) + 0.57(Mp3 + Mp2)/(Dht = Ds) where: (1) Mp1 = Mass of particulate...) for determination.) (2) Mp2 = Mass of particulate determined from the “stabilized” phase of the cold...

Measurements of particulate semi-volatile material

NASA Astrophysics Data System (ADS)

Pang, Yanbo

2000-10-01

A new innovative sampling system, PC-BOSS, was developed by the combination of particle concentrator and BOSS denuder techniques in response to the new EPA PM2.5 standard and to meet top research priorities for particulate matter that were identified by the National Research Council. The PC-BOSS (P_article C_oncentrator- B_righam Young University O_rganic S_ampling S_ystem) can accurately determine not only PM2.5 stable mass and species such as sulfate, but also particulate semi- volatile material. Several field comparison studies of the PC-BOSS with the EPA PM2.5 reference method and state-of-the-art fine particle measurement methods confirm the capability of the PC-BOSS to accurately determine particulate semi-volatile material, especially organic compounds. This is the first routine sampling system for the determination of both particulate semi-volatile inorganic and organic material. Two other denuder system samplers for the determination of PM2.5 total mass including semi-volatile material were also developed for PM2.5 research and exposure monitoring. Results of studies around the United States indicate that the EPA PM2.5 FRM (Federal Reference Method) under- measured PM2.5 mass by 20-30% compared to PC-BOSS results due to the loss of particulate nitrate and semi-volatile organic compounds during sampling. Organic material is mostly responsible for this under- measurement by the FRM. Using our new sampling system in epidemiological and exposure studies will be essential to providing answers to some top research priorities for particulate matter and promote a better PM2.5 standard for the protection of human health because some fractions of particulate semi-volatile organic compounds are toxic and are possibly responsible for health effects associated with exposure to particulate matter. The atmospheric chemistry of organic aerosols in the troposphere and stratosphere is still largely unknown because of the lack of detailed organic aerosol information. The

Zone heated diesel particulate filter electrical connection

DOEpatents

Gonze, Eugene V.; Paratore, Jr., Michael J.

2010-03-30

An electrical connection system for a particulate filter is provided. The system includes: a particulate filter (PF) disposed within an outer shell wherein the PF is segmented into a plurality of heating zones; an outer mat disposed between the particulate filter and the outer shell; an electrical connector coupled to the outer shell of the PF; and a plurality of printed circuit connections that extend along the outer surface of the PF from the electrical connector to the plurality of heating zones.

Transport de Particules et Atmospheres D'etoiles Magnetiques

NASA Astrophysics Data System (ADS)

LeBlanc, Francis

1995-01-01

Les phenomenes relies a la diffusion atomique dans les etoiles sont etudies de facon intensive depuis environ un quart de siecle. La diffusion peut a la fois modifier les abondances atomiques presentes ainsi qu'affecter la structure et l'evolution stellaires. Dans cette these, nous allons etudier trois phenomenes physiques relies a la diffusion. Nous avons developpe la theorie de la derive induite par la radiation afin qu'elle soit facilement applicable dans le contexte de l'astrophysique stellaire. Des calcuis detailles furent effectues afin d'evaluer l'importance de cet effet sur la diffusion relative de l'^3 He et l'^4He et montrent que la derive induite par la radiation accelere la separation de ces deux isotopes dans une etoile de temperature effective de 18000 K. Lorsque l'^4He est present, ce phenomene augmente la vitesse de derive de l'^3He qui migre vers l'exterieur ce qui fait apparai tre la surabondance de cet isotope plus tot dans l'evolution. Des calculs sur le lithium a la base de la zone convective d'une etoile avec une temperature effective de 6700 K monuent que la derive induite par la radiation n'est pas importante dans ce cas. Ce phenomene semble aussi etre negligeable pour l'oxygene dans les etoiles de type A ainsi que pour le mercure dans les etoiles de type B. Deuxiemement nous avons construit des modeles d'atmospheres d'etoiles ayant un champ magnetique horizontal et constant en incluant l'interaction entre ce champ et la diffusion ambipolaire de l'hydrogene. Cette interaction cause une compression de la zone d'ionisation de l'hydrogene. Dans un modele de temperature effective de 10,000 K, et avec log g = 4.0 la gravite effective, c'est-a-dire la gravite plus l'acceleration causee par la force de Lorentz, en presence d'un champ magnetique de 5 kG est sept fois plus grande que la gravite. Ce phenomene affecte donc fortement la structure des etoiles Ap. Cette modification de la structure des etoiles magnetiques cause un plus grand elargissement

Sensitive determination of total particulate phosphorus and particulate inorganic phosphorus in seawater using liquid waveguide spectrophotometry.

PubMed

Ehama, Makoto; Hashihama, Fuminori; Kinouchi, Shinko; Kanda, Jota; Saito, Hiroaki

2016-06-01

Determining the total particulate phosphorus (TPP) and particulate inorganic phosphorus (PIP) in oligotrophic oceanic water generally requires the filtration of a large amount of water sample. This paper describes methods that require small filtration volumes for determining the TPP and PIP concentrations. The methods were devised by validating or improving conventional sample processing and by applying highly sensitive liquid waveguide spectrophotometry to the measurements of oxidized or acid-extracted phosphate from TPP and PIP, respectively. The oxidation of TPP was performed by a chemical wet oxidation method using 3% potassium persulfate. The acid extraction of PIP was initially carried out based on the conventional extraction methodology, which requires 1M HCl, followed by the procedure for decreasing acidity. While the conventional procedure for acid removal requires a ten-fold dilution of the 1M HCl extract with purified water, the improved procedure proposed in this study uses 8M NaOH solution for neutralizing 1M HCl extract in order to reduce the dilution effect. An experiment for comparing the absorbances of the phosphate standard dissolved in 0.1M HCl and of that dissolved in a neutralized solution [1M HCl: 8M NaOH=8:1 (v:v)] exhibited a higher absorbance in the neutralized solution. This indicated that the improved procedure completely removed the acid effect, which reduces the sensitivity of the phosphate measurement. Application to an ultraoligotrophic water sample showed that the TPP concentration in a 1075mL-filtered sample was 8.4nM with a coefficient of variation (CV) of 4.3% and the PIP concentration in a 2300mL-filtered sample was 1.3nM with a CV of 6.1%. Based on the detection limit (3nM) of the sensitive phosphate measurement and the ambient TPP and PIP concentrations of the ultraoligotrophic water, the minimum filtration volumes required for the detection of TPP and PIP were estimated to be 15 and 52mL, respectively. Copyright © 2016

Biologically plausible particulate air pollution mortality concentration-response functions.

PubMed Central

Roberts, Steven

2004-01-01

In this article I introduce an alternative method for estimating particulate air pollution mortality concentration-response functions. This method constrains the particulate air pollution mortality concentration-response function to be biologically plausible--that is, a non-decreasing function of the particulate air pollution concentration. Using time-series data from Cook County, Illinois, the proposed method yields more meaningful particulate air pollution mortality concentration-response function estimates with an increase in statistical accuracy. PMID:14998745

Low exhaust temperature electrically heated particulate matter filter system

DOEpatents

Gonze, Eugene V [Pinckney, MI; Paratore, Jr., Michael J.; Bhatia, Garima [Bangalore, IN

2012-02-14

A system includes a particulate matter (PM) filter, a sensor, a heating element, and a control module. The PM filter includes with an upstream end that receives exhaust gas, a downstream end and multiple zones. The sensor detects a temperature of the exhaust gas. The control module controls current to the heating element to convection heat one of the zones and initiate a regeneration process. The control module selectively increases current to the heating element relative to a reference regeneration current level when the temperature is less than a predetermined temperature.

Air Quality Criteria for Particulate Matter.

ERIC Educational Resources Information Center

National Air Pollution Control Administration (DHEW), Washington, DC.

To assist states in developing air quality standards, this book offers a review of literature related to atmospheric particulates and the development of criteria for air quality. It not only summarizes the current scientific knowledge of particulate air pollution, but points up the major deficiencies in that knowledge and the need for further…

Direct sampling of sub-µm atmospheric particulate organic matter in sub-ng m-3 mass concentrations by proton-transfer-reaction mass spectrometry

NASA Astrophysics Data System (ADS)

Armin, W.; Mueller, M.; Klinger, A.; Striednig, M.

2017-12-01

A quantitative characterization of the organic fraction of atmospheric particulate matter is still challenging. Herein we present the novel modular "Chemical Analysis of Aerosol Online" (CHARON) particle inlet system coupled to a new-generation proton-transfer-reaction time-of-flight mass spectrometer (PTR-TOF 6000 X2, Ionicon Analytik, Austria) that quantitatively detects organic analytes in real-time and sub-pptV levels by chemical ionization with hydronium reagent ions. CHARON consists of a gas-phase denuder for stripping off gas-phase analytes (efficiency > 99.999%), an aerodynamic lens for particle collimation combined with an inertial sampler for the particle-enriched flow and a thermodesorption unit for particle volatilization prior to chemical analysis. With typical particle enrichment factors of around 30 for particle diameters (DP) between 120 nm and 1000 nm (somewhat reduced enrichment for 60 nm < DP < 120 nm) we boost the already excellent limits of detection of the PTR-TOF 6000 X2 system to unprecedented levels. We demonstrate that particulate organic analytes of mass concentrations down to 100 pg m-3 can be detected on-line and in single-minute time-resolutions. In addition, PTR-MS allows for a quantitative detection of almost the full range of particulate organics of intermediate to low volatility. With the high mass resolution (R > 6000) and excellent mass accuracies (< 10 ppm) chemical compositions can be assigned and included in further analyses. In addition to a detailed characterization of the CHARON PTR-TOF 6000 X2 we will present first results on the chemical composition of sub-µm particulate organic matter in the urban atmosphere in Innsbruck (Austria).

Detection of airborne Stachybotrys chartarum macrocyclic trichothecene mycotoxins on particulates smaller than conidia.

PubMed

Brasel, T L; Douglas, D R; Wilson, S C; Straus, D C

2005-01-01

Highly respirable particles (diameter, <1 microm) constitute the majority of particulate matter found in indoor air. It is hypothesized that these particles serve as carriers for toxic compounds, specifically the compounds produced by molds in water-damaged buildings. The presence of airborne Stachybotrys chartarum trichothecene mycotoxins on particles smaller than conidia (e.g., fungal fragments) was therefore investigated. Cellulose ceiling tiles with confluent Stachybotrys growth were placed in gas-drying containers through which filtered air was passed. Exiting particulates were collected by using a series of polycarbonate membrane filters with decreasing pore sizes. Scanning electron microscopy was employed to determine the presence of conidia on the filters. A competitive enzyme-linked immunosorbent assay (ELISA) specific for macrocyclic trichothecenes was used to analyze filter extracts. Cross-reactivity to various mycotoxins was examined to confirm the specificity. Statistically significant (P < 0.05) ELISA binding was observed primarily for macrocyclic trichothecenes at concentrations of 50 and 5 ng/ml and 500 pg/ml (58.4 to 83.5% inhibition). Of the remaining toxins tested, only verrucarol and diacetylverrucarol (nonmacrocyclic trichothecenes) demonstrated significant binding (18.2 and 51.7% inhibition, respectively) and then only at high concentrations. The results showed that extracts from conidium-free filters demonstrated statistically significant (P < 0.05) antibody binding that increased with sampling time (38.4 to 71.9% inhibition, representing a range of 0.5 to 4.0 ng/ml). High-performance liquid chromatography analysis suggested the presence of satratoxin H in conidium-free filter extracts. These data show that S. chartarum trichothecene mycotoxins can become airborne in association with intact conidia or smaller particles. These findings may have important implications for indoor air quality assessment.

CHARACTERIZATION OF PARTICULATE EMISSIONS FROM IN-USE DIESEL VEHICLES

EPA Science Inventory

Particulate emissions data are presented from a group of 19 in-use diesel automobiles. Five driving cycles and three fuel/lubricating oil combinations have been used to obtain particulate emissions data and also to collect particulate samples for chemical and bioassay characteriz...

Methods and apparatus for handling or treating particulate material

NASA Technical Reports Server (NTRS)

Littman, Howard (Inventor); Plawsky, Joel L. (Inventor); Paccione, John D. (Inventor)

2009-01-01

An improved draft tube spout fluid bed (DTSFB) mixing, handling, conveying, and treating apparatus and systems, and methods for operating are provided. The apparatus and systems can accept particulate material and pneumatically or hydraulically conveying the material to mix and/or treat the material. In addition to conveying apparatus, a collection and separation apparatus adapted to receive the conveyed particulate material is also provided. The collection apparatus may include an impaction plate against which the conveyed material is directed to improve mixing and/or treatment. The improved apparatus are characterized by means of controlling the operation of the pneumatic or hydraulic transfer to enhance the mixing and/or reacting by controlling the flow of fluids, for example, air, into and out of the apparatus. The disclosed apparatus may be used to mix particulate material, for example, mortar; react fluids with particulate material; coat particulate material, or simply convey particulate material.

Size- and structure-dependent toxicity of silica particulates

NASA Astrophysics Data System (ADS)

Hanada, Sanshiro; Miyaoi, Kenichi; Hoshino, Akiyoshi; Inasawa, Susumu; Yamaguchi, Yukio; Yamamoto, Kenji

2011-03-01

Nano- and micro-particulates firmly attach with the surface of various biological systems. In some chronic pulmonary disease such as asbestosis and silicosis, causative particulates will induce chronic inflammatory disorder, followed by poor prognosis diseases. However, nano- and micro-scale specific toxicity of silica particulates is not well examined enough to recognize the risk of nano- and micro-particulates from the clinical aspect. To clarify the effect of the size and structure of silica particulates on the cellular damage and the biological response, we assessed the cytotoxicity of the various kinds of silica particles including amorphous and crystalline silica, in mouse alveolar macrophage culture, focusing on the fibrotic and inflammatory response. Our study showed that the cytotoxicity, which depends on the particle size and surface area, is correlated with their inflammatory response. By contrast, production of TGF-β, which is one of the fibrotic agents in lung, by addition of crystal silica was much higher than that of amorphous silica. We conclude that fibrosis and inflammation are induced at different phases and that the size- and structure-differences of silica particulates affect the both biological responses, caused by surface activity, radical species, and so on.

The desA and desB genes from Clostridium scindens ATCC 35704 encode steroid-17,20-desmolase.

PubMed

Devendran, Saravanan; Mythen, Sean M; Ridlon, Jason M

2018-06-01

Clostridium scindens is a gut microbe capable of removing the side-chain of cortisol, forming 11β-hydro-xyandrostenedione. A cortisol-inducible operon ( desABCD ) was previously identified in C. scindens ATCC 35704 by RNA-Seq. The desC gene was shown to encode a cortisol 20α-hydroxysteroid dehydrogenase (20α-HSDH). The desD encodes a protein annotated as a member of the major facilitator family, predicted to function as a cortisol transporter. The desA and desB genes are annotated as N-terminal and C-terminal transketolases, respectively. We hypothesized that the DesAB forms a complex and has steroid-17,20-desmolase activity. We cloned the desA and desB genes from C. scindens ATCC 35704 in pETDuet for overexpression in Escherichia coli The purified recombinant DesAB was determined to be a 142 ± 5.4 kDa heterotetramer. We developed an enzyme-linked continuous spectrophotometric assay to quantify steroid-17,20-desmolase. This was achieved by coupling DesAB-dependent formation of 11β-hydroxyandrostenedione with the NADPH-dependent reduction of the steroid 17-keto group by a recombinant 17β-HSDH from the filamentous fungus, Cochliobolus lunatus The pH optimum for the coupled assay was 7.0 and kinetic constants using cortisol as substrate were K m of 4.96 ± 0.57 µM and k cat of 0.87 ± 0.076 min -1 Substrate-specificity studies revealed that rDesAB recognized substrates regardless of 11β-hydroxylation, but had an absolute requirement for 17,21-dihydroxy 20-ketosteroids. Copyright © 2018 Devendran et al.

Association of expired nitric oxide with occupational particulate exposure.

PubMed Central

Kim, Jee Young; Wand, Matthew P; Hauser, Russ; Mukherjee, Sutapa; Herrick, Robert F; Christiani, David C

2003-01-01

Particulate air pollution has been associated with adverse respiratory health effects. This study assessed the utility of expired nitric oxide to detect acute airway responses to metal-containing fine particulates. Using a repeated-measures study design, we investigated the association between the fractional concentration of expired nitric oxide (F(E)NO) and exposure to particulate matter with an aerodynamic mass median diameter of less than or equal to 2.5 micro m (PM(2.5)) in boilermakers exposed to residual oil fly ash and metal fumes. Subjects were monitored for 5 days during boiler repair overhauls in 1999 (n = 20) or 2000 (n = 14). The Wilcoxon median baseline F(E)NO was 10.6 ppb [95% confidence interval (CI): 9.1, 12.7] in 1999 and 7.4 ppb (95% CI: 6.7, 8.0) in 2000. The Wilcoxon median PM(2.5) 8-hr time-weighted average was 0.56 mg/m(3) (95% CI: 0.37, 0.93) in 1999 and 0.86 mg/m(3) (95% CI: 0.65, 1.07) in 2000. F(E)NO levels during the work week were significantly lower than baseline F(E)NO in 1999 (p < 0.001). A significant inverse exposure-response relationship between log-transformed F(E)NO and the previous workday's PM(2.5) concentration was found in 1999, after adjusting for smoking status, age, and sampling year. With each 1 mg/m(3) incremental increase in PM(2.5) exposure, log F(E)NO decreased by 0.24 (95% CI: -0.38, -0.10) in 1999. The lack of an exposure-response relationship between PM(2.5) exposure and F(E)NO in 2000 could be attributable to exposure misclassification resulting from the use of respirators. In conclusion, occupational exposure to metal-containing fine particulates was associated with significant decreases in F(E)NO in a survey of workers with limited respirator usage. PMID:12727593

Detection of monohydroxylated polycyclic aromatic hydrocarbons in urine and particulate matter using LC separations coupled with integrated SPE and fluorescence detection or coupled with high-resolution time-of-flight mass spectrometry.

PubMed

Lintelmann, Jutta; Wu, Xiao; Kuhn, Evelyn; Ritter, Sebastian; Schmidt, Claudia; Zimmermann, Ralf

2018-05-01

A high-performance liquid chromatographic (HPLC) method with integrated solid-phase extraction for the determination of 1-hydroxypyrene and 1-, 2-, 3-, 4- and 9-hydroxyphenanthrene in urine was developed and validated. After enzymatic treatment and centrifugation of 500 μL urine, 100 μL of the sample was directly injected into the HPLC system. Integrated solid-phase extraction was performed on a selective, copper phthalocyanine modified packing material. Subsequent chromatographic separation was achieved on a pentafluorophenyl core-shell column using a methanol gradient. For quantification, time-programmed fluorescence detection was used. Matrix-dependent recoveries were between 94.8 and 102.4%, repeatability and reproducibility ranged from 2.2 to 17.9% and detection limits lay between 2.6 and 13.6 ng/L urine. A set of 16 samples from normally exposed adults was analyzed using this HPLC-fluorescence detection method. Results were comparable with those reported in other studies. The chromatographic separation of the method was transferred to an ultra-high-performance liquid chromatography pentafluorophenyl core-shell column and coupled to a high-resolution time-of-flight mass spectrometer (HR-TOF-MS). The resulting method was used to demonstrate the applicability of LC-HR-TOF-MS for simultaneous target and suspect screening of monohydroxylated polycyclic aromatic hydrocarbons in extracts of urine and particulate matter. Copyright © 2018 John Wiley & Sons, Ltd.

Advanced Hybrid Particulate Collector Project Management Plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, S.J.

As the consumption of energy increases, its impact on ambient air quality has become a significant concern. Recent studies indicate that fine particles from coal combustion cause health problems as well as atmospheric visibility impairment. These problems are further compounded by the concentration of hazardous trace elements such as mercury, cadmium, selenium, and arsenic in fine particles. Therefore, a current need exists to develop superior, but economical, methods to control emissions of fine particles. Since most of the toxic metals present in coal will be in particulate form, a high level of fine- particle collection appears to be the bestmore » method of overall air toxics control. However, over 50% of mercury and a portion of selenium emissions are in vapor form and cannot be collected in particulate control devices. Therefore, this project will focus on developing technology not only to provide ultrahigh collection efficiency of particulate air toxic emissions, but also to capture vapor- phase trace metals such as mercury and selenium. Currently, the primary state-of-the-art technologies for particulate control are fabric filters (baghouses) and electrostatic precipitators (ESPs). However, they both have limitations that prevent them from achieving ultrahigh collection of fine particulate matter and vapor-phase trace metals. The objective of this project is to develop a highly reliable advanced hybrid particulate collector (AHPC) that can provide > 99.99 % particulate collection efficiency for all particle sizes between 0.01 and 50 14m, is applicable for use with all U.S. coals, and is cost-0443competitive with existing technologies. Phase I of the project is organized into three tasks: Task I - Project Management, Reporting, and Subcontract Consulting Task 2 - Modeling, Design, and Construction of 200-acfm AHPC Model Task 3 - Experimental Testing and Subcontract Consulting« less

Process for off-gas particulate removal and apparatus therefor

DOEpatents

Carl, D.E.

1997-10-21

In the event of a breach in the off-gas line of a melter operation requiring closure of the line, a secondary vessel vent line is provided with a particulate collector utilizing atomization for removal of large particulates from the off-gas. The collector receives the gas containing particulates and directs a portion of the gas through outer and inner annular channels. The collector further receives a fluid, such as water, which is directed through the outer channel together with a second portion of the particulate-laden gas. The outer and inner channels have respective ring-like termination apertures concentrically disposed adjacent one another on the outer edge of the downstream side of the particulate collector. Each of the outer and inner channels curves outwardly away from the collector`s centerline in proceeding toward the downstream side of the collector. Gas flow in the outer channel maintains the fluid on the channel`s wall in the form of a ``wavy film,`` while the gas stream from the inner channel shears the fluid film as it exits the outer channel in reducing the fluid to small droplets. Droplets formed by the collector capture particulates in the gas stream by one of three mechanisms: impaction, interception or Brownian diffusion in removing the particulates. The particulate-laden droplets are removed from the fluid stream by a vessel vent condenser or mist eliminator. 4 figs.

Global Particulate Matter Source Apportionment

NASA Astrophysics Data System (ADS)

Lamancusa, C.; Wagstrom, K.

2017-12-01

As our global society develops and grows it is necessary to better understand the impacts and nuances of atmospheric chemistry, in particular those associated with atmospheric particulate matter. We have developed a source apportionment scheme for the GEOS-Chem global atmospheric chemical transport model. While these approaches have existed for several years in regional chemical transport models, the Global Particulate Matter Source Apportionment Technology (GPSAT) represents the first incorporation into a global chemical transport model. GPSAT runs in parallel to a standard GEOS-Chem run. GPSAT uses the fact that all molecules of a given species have the same probability of undergoing any given process as a core principle. This allows GPSAT to track many different species using only the flux information provided by GEOS-Chem's many processes. GPSAT accounts for the change in source specific concentrations as a result of aqueous and gas-phase chemistry, horizontal and vertical transport, condensation and evaporation on particulate matter, emissions, and wet and dry deposition. By using fluxes, GPSAT minimizes computational cost by circumventing the computationally costly chemistry and transport solvers. GPSAT will allow researchers to address many pertinent research questions about global particulate matter including the global impact of emissions from different source regions and the climate impacts from different source types and regions. For this first application of GPSAT, we investigate the contribution of the twenty largest urban areas worldwide to global particulate matter concentrations. The species investigated include: ammonium, nitrates, sulfates, and the secondary organic aerosols formed by the oxidation of benzene, isoprene, and terpenes. While GPSAT is not yet publically available, we will incorporate it into a future standard release of GEOS-Chem so that all GEOS-Chem users will have access to this new tool.

Techniques d'inspection par ondes guidees ultrasonores d'assemblages brases dans des reacteurs aeronautiques =

NASA Astrophysics Data System (ADS)

Comot, Pierre

L'industrie aeronautique, cherche a etudier la possibilite d'utiliser de maniere structurelle des joints brases, dans une optique de reduction de poids et de cout. Le developpement d'une methode d'evaluation rapide, fiable et peu couteuse pour evaluer l'integrite structurelle des joints apparait donc indispensable. La resistance mecanique d'un joint brase dependant principalement de la quantite de phase fragile dans sa microstructure. Les ondes guidees ultrasonores permettent de detecter ce type de phase lorsqu'elles sont couplees a une mesure spatio-temporelle. De plus la nature de ce type d'ondes permet l'inspection de joints ayant des formes complexes. Ce memoire se concentre donc sur le developpement d'une technique basee sur l'utilisation d'ondes guidees ultrasonores pour l'inspection de joints brases a recouvrement d'Inconel 625 avec comme metal d'apport du BNi-2. Dans un premiers temps un modele elements finis du joint a ete utilise pour simuler la propagation des ultrasons et optimiser les parametres d'inspection, la simulation a permis egalement de demontrer la faisabilite de la technique pour la detection de la quantite de phase fragile dans ce type de joints. Les parametres optimises sont la forme de signal d'excitation, sa frequence centrale et la direction d'excitation. Les simulations ont montre que l'energie de l'onde ultrasonore transmise a travers le joint aussi bien que celle reflechie, toutes deux extraites des courbes de dispersion, etaient proportionnelles a la quantite de phase fragile presente dans le joint et donc cette methode permet d'identifier la presence ou non d'une phase fragile dans ce type de joint. Ensuite des experimentations ont ete menees sur trois echantillons typiques presentant differentes quantites de phase fragile dans le joint, pour obtenir ce type d'echantillons differents temps de brasage ont ete utilises (1, 60 et 180 min). Pour cela un banc d'essai automatise a ete developpe permettant d'effectuer une analyse similaire

PARTICULATE EMISSION MEASUREMENTS FROM CONTROLLED CONSTRUCTION ACTIVITIES

EPA Science Inventory

The report summarized the results of field testing of the effectiveness of control measures for sources of fugitive particulate emissions found at construction sites. The effectiveness of watering temporary, unpaved travel surfaces on emissions of particulate matter with aerodyna...

Determination of particulate lead during MILAGRO / MCMA-2006 using Aerosol Mass Spectrometry

NASA Astrophysics Data System (ADS)

Salcedo, Dara; Onasch, T. B.; Aiken, A. C.; Williams, L. R.; de Foy, B.; Cubison, M. J.; Worsnop, D. R.; Molina, L. T.; Jimenez, J. L.

2010-05-01

We report the first measurements of particulate lead (Pb) from Aerodyne Aerosol Mass Spectrometers, which were deployed in and around Mexico City during the Megacity Initiative: Local and Global Research Observations (MILAGRO) / Mexico City Metropolitan Area 2006 (MCMA-2006) field campaigns. The high resolution mass spectrometer of one of the AMS instruments (HR-AMS) and the measured isotopic ratios unequivocally prove the detection of Pb in ambient particles. A substantial fraction of the lead evaporated slowly from the vaporizer of the instruments, which is indicative of species with low volatility at 600oC. A model was developed in order to estimate the ambient particulate Pb entering the AMS from the signals in the "open" and the "closed" (or "background") mass spectrum modes of the AMS. The model suggests the presence of at least two lead fractions with ~25% of the Pb signal exhibiting rapid evaporation (1/e decay constant, τ < 0.1 s) and ~75% exhibiting slow evaporation (τ ~2.4 min) at T0 and a different fraction (70% prompt and 30% slow evaporation) at a site northwest from the metropolitan area (PEMEX32 site). From laboratory experiments with pure Pb(NO3)2 particles, we estimated that the Pb ionization efficiency relative to nitrate (RIEPb) is 0.5. Comparison of time series of AMS Pb with other measurements carried out at the T0 urban supersite during MILAGRO (using Proton Induced X-ray Emission (PIXE), Inductively-Coupled Plasma Mass Spectrometry (ICP-MS) and single-particle counts from an Aerosol Time-of-Fight Mass Spectrometer (ATOFMS)) shows similar levels (for PIXE and ICP-MS) and substantial correlation. During part of the campaign, sampling at T0 was alternated every 10 minutes with an Aerosol Concentrator, which enabled the detection of signals for PbCl+ and PbS+ ions. PbS+ displays the signature of a slowly evaporating species, while PbCl+ appears to arise only from fast evaporation, which is likely due to the higher vapor pressure of the

40 CFR 52.725 - Control strategy: Particulates.

Code of Federal Regulations, 2011 CFR

2011-07-01

... requests to redesignate the Granite City Particulate Matter (PM) nonattainment area to attainment status... Granite City area to ensure continued attainment of the NAAQS. The redesignation request and maintenance... the Lake Calumet (SE Chicago), McCook, and Granite City, Illinois, Particulate Matter (PM...

40 CFR 52.725 - Control strategy: Particulates.

Code of Federal Regulations, 2010 CFR

2010-07-01

... requests to redesignate the Granite City Particulate Matter (PM) nonattainment area to attainment status... Granite City area to ensure continued attainment of the NAAQS. The redesignation request and maintenance... the Lake Calumet (SE Chicago), McCook, and Granite City, Illinois, Particulate Matter (PM...

40 CFR 52.725 - Control strategy: Particulates.

Code of Federal Regulations, 2013 CFR

2013-07-01

... requests to redesignate the Granite City Particulate Matter (PM) nonattainment area to attainment status... Granite City area to ensure continued attainment of the NAAQS. The redesignation request and maintenance... the Lake Calumet (SE Chicago), McCook, and Granite City, Illinois, Particulate Matter (PM...

40 CFR 52.725 - Control strategy: Particulates.

Code of Federal Regulations, 2014 CFR

2014-07-01

... requests to redesignate the Granite City Particulate Matter (PM) nonattainment area to attainment status... Granite City area to ensure continued attainment of the NAAQS. The redesignation request and maintenance... the Lake Calumet (SE Chicago), McCook, and Granite City, Illinois, Particulate Matter (PM...

Estimation of particulate matter from simulation and measurements

NASA Astrophysics Data System (ADS)

Nakata, Makiko; Nakano, Tomio; Okuhara, Takaaki; Sano, Itaru; Mukai, Sonoyo

2011-11-01

The particulate matter is a typical indicator of small particles in the atmosphere. In addition to providing impacts on climate and environment, these small particles can bring adverse effects on human health. Then an accurate estimation of particulate matter is an urgent subject. We set up SPM sampler attached to our AERONET (Aerosol Robotics Network) station in urban city of Higashi-Osaka in Japan. The SPM sampler provides particle information about the concentrations of various SPMs (e.g., PM10 and PM2.5) separately. The AEROENT program is world wide ground based sunphotometric observation networks by NASA and provides the spectral information about aerosol optical thickness (AOT) and Angstrom exponent (α). Simultaneous measurements show that a linear correlation definitely exists between AOT and PM2.5. These results indicate that particulate matter can be estimated from AOT. However AOT represents integrated values of column aerosol amount retrieved from optical property, while particulate matter concentration presents in-situ aerosol loading on the surface. Then simple way using linear correlation brings the discrepancy between observed and estimated particulate matter. In this work, we use cluster information about aerosol type to reduce the discrepancy. Our improved method will be useful for retrieving particulate matter from satellite measurements.

PRODUCTION OF SHEET FROM PARTICULATE MATERIAL

DOEpatents

Blainey, A.

1959-05-12

A process is presented for forming coherent sheet material from particulate material such as granular or powdered metal, granular or powdered oxide, slurries, pastes, and plastic mixes which cohere under pressure. The primary object is to avoid the use of expensive and/ or short lived pressing tools, that is, dies and specially profiled rolls, and so to reduce the cost of the product and to prcvide in a simple manner for the making of the product in a variety of shapes or sizes. The sheet material is formed when the particulate material is laterally confined in a boundary material deformable in all lateral directions under axial pressure and then axially compressing the layer of particulate material together with the boundary material.

Aircraft Disinsection: A Guide for Military and Civilian Air Carriers (Desinsectisation des aeronefs: Un guide a l’intention des responsables des transports aeriens civils et militaires)

DTIC Science & Technology

1996-04-01

regulations. - Ceratitis capitata (Mediterranean fruit fly). Quarantine regulations generally reduce - Rhagoletis pomonella (Apple maggot). the chances of a...d’insectes nuisibles dans un pays, en 6vitant des risques pour la sant6 des 6quipages, pour la s~curit6 de 1’a~ronef et pour l’industrie. Ce rapport examine 1...diffrrents officiels responsables de la r~glementation des insectes nuisibles introduits, de l’inscription des pesticides et de leur utilisation en

Characterization of particulate matter binding peptides screened from phage display.

PubMed

Liang Alvin, Aw Wei; Tanaka, Masayoshi; Okochi, Mina

2017-05-01

Particulate matter (PM), especially particulates with diameters of less than 2.5 μm, can penetrate the alveolar region and increase the risk of respiratory diseases. This has stimulated research efforts to develop detection methods so that counter measures can be taken. In this study, four PM binding peptides were obtained by phage display and binding characteristics of these peptides were investigated using the peptide array. The strongest binding peptide, WQDFGAVRSTRS, displayed a binding property, measured in terms of spot intensity, 11.4 times higher than that of the negative control, AAAAA. Inductively coupled plasma mass spectrometry (ICPMS) analysis of the transition metal compounds in the PM bound to the peptide spots was performed, and two peptides showed higher binding towards Cu and Zn compounds in PM. These results suggest that the screened peptides could serve as an indicator of transition metal compounds, which are related to adverse health effects, contained in PM. Copyright © 2017 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

Contribution of organic particulates to respiratory cancer.

PubMed Central

Matanoski, G; Fishbein, L; Redmond, C; Rosenkranz, H; Wallace, L

1986-01-01

This paper presents some of the issues that remain to be resolved in order to assess the risk of cancer related to exposure to organic particulates. Most reviews of the effects of organic particulates from the outdoor environment on the risk of lung cancer show that this source seems to play a minor role. However, as fuel use and chemical composition of air pollutants change, the contribution of outdoor pollution as a cause of cancer may also change. Indoor air pollution is a more important source of exposure to organic particulates than is outdoor exposure. Although there is clear evidence that in occupational settings organic particulates cause human cancer, there has been almost no study of exposure to these types of particulates within indoor settings. Previous research has focused on cigarette smoke as the major indoor pollutant, but more specific characterization of contaminants in both the workplace and the home is required. The health effects of the higher levels of some of these contaminants in the workplace should be evaluated and the results extrapolated to populations exposed to lower levels in the home. Extensive research is needed to characterize organic particulate mixtures appropriately and test them for carcinogenicity. Studies on the health risks of nitropolynuclear aromatic hydrocarbons and polychlorinated dibenzodioxins and dibenzofurans are reviewed, but their contribution to the overall burden of respiratory cancer in humans cannot be estimated at this time. Characterization of mixtures, assessment of exposures, and linkage of exposures to health effects are the objectives of the recommendations proposed for further research. PMID:3830112

Diesel particulate filter regeneration via resistive surface heating

DOEpatents

Gonze, Eugene V; Ament, Frank

2013-10-08

An exhaust system that processes exhaust generated by an engine is provided. The system includes: a particulate filter (PF) that filters particulates from the exhaust wherein an upstream end of the PF receives exhaust from the engine; and a grid of electrically resistive material that is applied to an exterior upstream surface of the PF and that selectively heats exhaust passing through the grid to initiate combustion of particulates within the PF.

Exposure to particulate hexavalent chromium exacerbates allergic asthma pathology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schneider, Brent C.; Department of Pharmacology and Physiology, The George Washington University, Washington, DC 20037; Constant, Stephanie L.

Airborne hexavalent chromate, Cr(VI), has been identified by the Environmental Protection Agency as a possible health threat in urban areas, due to the carcinogenic potential of some of its forms. Particulate chromates are produced in many different industrial settings, with high levels of aerosolized forms historically documented. Along with an increased risk of lung cancer, a high incidence of allergic asthma has been reported in workers exposed to certain inhaled particulate Cr(VI) compounds. However, a direct causal association between Cr(VI) and allergic asthma has not been established. We recently showed that inhaled particulate Cr(VI) induces an innate neutrophilic inflammatory responsemore » in BALB/c mice. In the current studies we investigated how the inflammation induced by inhaled particulate Cr(VI) might alter the pathology of an allergic asthmatic response. We used a well-established mouse model of allergic asthma. Groups of ovalbumin protein (OVA)-primed mice were challenged either with OVA alone, or with a combination of OVA and particulate zinc chromate, and various parameters associated with asthmatic responses were measured. Co-exposure to particulate Cr(VI) and OVA mediated a mixed form of asthma in which both eosinophils and neutrophils are present in airways, tissue pathology is markedly exacerbated, and airway hyperresponsiveness is significantly increased. Taken together these findings suggest that inhalation of particulate forms of Cr(VI) may augment the severity of ongoing allergic asthma, as well as alter its phenotype. Such findings may have implications for asthmatics in settings in which airborne particulate Cr(VI) compounds are present at high levels. -- Highlights: ► Allergic asthma correlated with exposure to certain inhaled particulate chromates. ► Direct causal association between Cr(VI) and allergic asthma not established. ► Cr exacerbated pathology and airway hyperresponsiveness in an OVA-challenged mouse. �

Gastric emptying of multi-particulate dosage forms.

PubMed

Newton, J Michael

2010-08-16

The evidence in the literature for the concept that multi-particulate dosage forms below a specific size empty from the stomach as if they were liquids and hence have the potential to provide the best solution to the formulation of controlled release oral dosage forms, has been considered. There is some evidence that particles less than 1.0mm provide a more rapid response than larger size particles but there is also evidence that this is not always the case and that rapid and reproducible gastric emptying of small particles does not always occur when they are administered. There is strong evidence that food can delay the gastric emptying of multi-particulate systems. Some of the misconception for gastric emptying performance of multi-particulate system is shown to be related to the limitation of the study design and limitation of the way the data is processed. Nevertheless, there is clear evidence that multi-particulate systems can provide effective oral controlled release dosage forms. There is still some way to go with experimental techniques which would allow a definitive answer to the issue of how the variability of the gastric emptying of multi-particulate systems of less than 2.0mm arises. Copyright (c) 2010 Elsevier B.V. All rights reserved.

A Microfluidic Paper-Based Analytical Device for Rapid Quantification of Particulate Chromium

PubMed Central

Rattanarat, Poomrat; Dungchai, Wijitar; Cate, David M.; Siangproh, Weena; Volckens, John; Chailapakul, Orawon; Henry, Charles S.

2013-01-01

Occupational exposure to Cr is concerning because of its myriad of health effects. Assessing chromium exposure is also cost and resource intensive because the analysis typically uses sophisticated instrumental techniques like Inductively-Coupled Plasma-Mass Spectrometry (ICP-MS). Here, we report a novel, simple, inexpensive microfluidic paper-based analytical device (µPAD) for measuring total Cr in airborne particulate matter. In the µPAD, tetravalent cerium (Ce(IV)) was used in a pretreatment zone to oxidize all soluble Cr to Cr(VI). After elution to the detection zone, Cr(VI) reacts with 1,5-diphenylcarbazide (1,5- DPC) forming 1,5-diphenylcarbazone (DPCO) and Cr(III). The resulting Cr(III) forms a distinct purple colored complex with the DPCO. As proof-of-principle, particulate matter (PM) collected on a sample filter was analyzed with the µPAD to quantify the mass of total Cr. A log-linear working range (0.23–3.75 µg; r2=0.998) between Cr and color intensity was obtained with a detection limit of 0.12 µg. For validation, a certified reference containing multiple competing metals was analyzed. Quantitative agreement was obtained between known Cr levels in the sample and the Cr measured using the µPAD. PMID:24120167

Analysis of particulate contamination on tape lift samples from the VETA optical surfaces

NASA Technical Reports Server (NTRS)

Germani, Mark S.

1992-01-01

Particulate contamination analysis was carried out on samples taken from the Verification Engineering Test Article (VETA) x-ray detection system. A total of eighteen tape lift samples were taken from the VETA optical surfaces. Initially, the samples were tested using a scanning electron microscope. Additionally, particle composition was determined by energy dispersive x-ray spectrometry. Results are presented in terms of particle loading per sample.

Diesel particulate filter (DPF) regeneration by electrical heating of resistive coatings

DOEpatents

Williamson, Weldon S [Malibu, CA; Gonze, Eugene V [Pinckney, MI

2008-12-30

An exhaust system that processes exhaust generated by an engine includes a diesel particulate filter (DPF) that is disposed downstream of the engine and that filters particulates from the exhaust. An electrical heater is integrally formed in an upstream end of the DPF and selectively heats the exhaust to initiate combustion of the particulates within the exhaust as it passes therethrough. Heat generated by combustion of the particulates induces combustion of particulates within the DPF.

Etude des phenomenes dynamiques ultrarapides et des caracteristiques impulsionnelles d'emission terahertz du supraconducteur YBCO

NASA Astrophysics Data System (ADS)

Savard, Stephane

Les premieres etudes d'antennes a base de supraconducteurs a haute temperature critique emettant une impulsion electromagnetique dont le contenu en frequence se situe dans le domaine terahertz remontent a 1996. Une antenne supraconductrice est formee d'un micro-pont d'une couche mince supraconductrice sur lequel un courant continu est applique. Un faisceau laser dans le visible est focalise sur le micro-pont et place le supraconducteur dans un etat hors-equilibre ou des paires sont brisees. Grace a la relaxation des quasiparticules en surplus et eventuellement de la reformation des paires supraconductrices, nous pouvons etudier la nature de la supraconductivite. L'analyse de la cinetique temporelle du champ electromagnetique emis par une telle antenne terahertz supraconductrice s'est averee utile pour decrire qualitativement les caracteristiques de celle-ci en fonction des parametres d'operation tels que le courant applique, la temperature et la puissance d'excitation. La comprehension de l'etat hors-equilibre est la cle pour comprendre le fonctionnement des antennes terahertz supraconductrices a haute temperature critique. Dans le but de comprendre ultimement cet etat hors-equilibre, nous avions besoin d'une methode et d'un modele pour extraire de facon plus systematique les proprietes intrinseques du materiau qui compose l'antenne terahertz a partir des caracteristiques d'emission de celle-ci. Nous avons developpe une procedure pour calibrer le spectrometre dans le domaine temporel en utilisant des antennes terahertz de GaAs bombarde aux protons H+ comme emetteur et detecteur. Une fois le montage calibre, nous y avons insere une antenne emettrice dipolaire de YBa 2Cu3O7-delta . Un modele avec des fonctions exponentielles de montee et de descente du signal est utilise pour lisser le spectre du champ electromagnetique de l'antenne de YBa 2Cu3O7-delta, ce qui nous permet d'extraire les proprietes intrinseques de ce dernier. Pour confirmer la validite du modele

Developpement d'une methode calorimetrique de mesure des pertes ac pour des rubans supraconducteurs a haute temperature critique

NASA Astrophysics Data System (ADS)

Dolez, Patricia

Le travail de recherche effectue dans le cadre de ce projet de doctorat a permis la mise au point d'une methode de mesure des pertes ac destinee a l'etude des supraconducteurs a haute temperature critique. Pour le choix des principes de cette methode, nous nous sommes inspires de travaux anterieurs realises sur les supraconducteurs conventionnels, afin de proposer une alternative a la technique electrique, presentant lors du debut de cette these des problemes lies a la variation du resultat des mesures selon la position des contacts de tension sur la surface de l'echantillon, et de pouvoir mesurer les pertes ac dans des conditions simulant la realite des futures applications industrielles des rubans supraconducteurs: en particulier, cette methode utilise la technique calorimetrique, associee a une calibration simultanee et in situ. La validite de la methode a ete verifiee de maniere theorique et experimentale: d'une part, des mesures ont ete realisees sur des echantillons de Bi-2223 recouverts d'argent ou d'alliage d'argent-or et comparees avec les predictions theoriques donnees par Norris, nous indiquant la nature majoritairement hysteretique des pertes ac dans nos echantillons; d'autre part, une mesure electrique a ete realisee in situ dont les resultats correspondent parfaitement a ceux donnes par notre methode calorimetrique. Par ailleurs, nous avons compare la dependance en courant et en frequence des pertes ac d'un echantillon avant et apres qu'il ait ete endommage. Ces mesures semblent indiquer une relation entre la valeur du coefficient de la loi de puissance modelisant la dependance des pertes avec le courant, et les inhomogeneites longitudinales du courant critique induites par l'endommagement. De plus, la variation en frequence montre qu'au niveau des grosses fractures transverses creees par l'endommagement dans le coeur supraconducteur, le courant se partage localement de maniere a peu pres equivalente entre les quelques grains de matiere

40 CFR 60.142a - Standards for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standards for particulate matter. 60... 20, 1983 § 60.142a Standards for particulate matter. (a) Except as provided under paragraphs (b) and...-blown BOPF and contain particulate matter in excess of 23 mg/dscm (0.010 gr/dscf). (3) Exit from a...

40 CFR 60.142a - Standards for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standards for particulate matter. 60... 20, 1983 § 60.142a Standards for particulate matter. (a) Except as provided under paragraphs (b) and...-blown BOPF and contain particulate matter in excess of 23 mg/dscm (0.010 gr/dscf). (3) Exit from a...

40 CFR 60.272a - Standard for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standard for particulate matter. 60... Standard for particulate matter. (a) On and after the date of which the performance test required to be... control device and contain particulate matter in excess of 12 mg/dscm (0.0052 gr/dscf); (2) Exit from a...

40 CFR 60.272a - Standard for particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Standard for particulate matter. 60... Standard for particulate matter. (a) On and after the date of which the performance test required to be... control device and contain particulate matter in excess of 12 mg/dscm (0.0052 gr/dscf); (2) Exit from a...

40 CFR 60.142a - Standards for particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standards for particulate matter. 60... 20, 1983 § 60.142a Standards for particulate matter. (a) Except as provided under paragraphs (b) and...-blown BOPF and contain particulate matter in excess of 23 mg/dscm (0.010 gr/dscf). (3) Exit from a...

40 CFR 60.272a - Standard for particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standard for particulate matter. 60... Standard for particulate matter. (a) On and after the date of which the performance test required to be... control device and contain particulate matter in excess of 12 mg/dscm (0.0052 gr/dscf); (2) Exit from a...

40 CFR 60.142a - Standards for particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false Standards for particulate matter. 60... 20, 1983 § 60.142a Standards for particulate matter. (a) Except as provided under paragraphs (b) and...-blown BOPF and contain particulate matter in excess of 23 mg/dscm (0.010 gr/dscf). (3) Exit from a...

40 CFR 60.272a - Standard for particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for particulate matter. 60... Standard for particulate matter. (a) On and after the date of which the performance test required to be... control device and contain particulate matter in excess of 12 mg/dscm (0.0052 gr/dscf); (2) Exit from a...

40 CFR 60.142a - Standards for particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false Standards for particulate matter. 60... 20, 1983 § 60.142a Standards for particulate matter. (a) Except as provided under paragraphs (b) and...-blown BOPF and contain particulate matter in excess of 23 mg/dscm (0.010 gr/dscf). (3) Exit from a...

40 CFR 60.272a - Standard for particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standard for particulate matter. 60... Standard for particulate matter. (a) On and after the date of which the performance test required to be... control device and contain particulate matter in excess of 12 mg/dscm (0.0052 gr/dscf); (2) Exit from a...

Consequences experimentales des effets des fluctuations du vide sur la fluorescence parametrique et la generation du second harmonique en milieu confine

NASA Astrophysics Data System (ADS)

Robichaud, Luc

Les fluctuations du vide, qui consistent en l'apparition momentanee de particules, ce qui est permit par le principe d'incertitude de Heisenberg, joue un role primordial dans les processus photoniques, en particulier les processus non-lineaires. Par la manipulation de ces fluctuations du vide a l'aide de confinement optique, on retrouve deux phenomenes particuliers : l'intensification de la fluorescence parametrique (Walker, 2008) et l'inhibition de la generation du second harmonique (Collette, 2013). Dans ce travail, on presente les resultats dans le cas classique ; c'est-a-dire sans fluctuations du vide et confinement. Par la suite, on presente les effets des fluctuations du vide et du confinement, ce qui mene aux deux effets mentionnes. Dans le cas de la fluorescence parametrique, le bruit quantique sur le champ interne et externe est calcule, le role du desaccord de phase dans le modele est expose et une generalisation tridimensionnelle est etudiee afin de generaliser la conception du modele d'un cas unidimensionnel a un cas tridimensionnel planaire. Dans le cas de la generation du second harmonique, les difficultes d'un modele purement tridimensionnel sont exposees et ensuite le cas limite planaire est etudie.

Shielded regeneration heating element for a particulate filter

DOEpatents

Gonze, Eugene V [Pinckney, MI; Ament, Frank [Troy, MI

2011-01-04

An exhaust system includes a particulate filter (PF) that is disposed downstream from an engine. The PF filters particulates within an exhaust from the engine. A heating element heats particulate matter in the PF. A catalyst substrate or a flow converter is disposed upstream from said heating element. The catalyst substrate oxidizes the exhaust prior to reception by the heating element. The flow converter converts turbulent exhaust flow to laminar exhaust flow prior to reception by the heating element.

Cartographie des disques

NASA Astrophysics Data System (ADS)

Hameury, Jean-Marie

2001-01-01

Two techniques are frequently used to produce images of the accretion disc in an eclipsing binary: eclipse mapping and Doppler tomography. From the light curve, one can deduce the radial distribution of the effective temperature, assuming axial symmetry. On the other hand, from the variation of the line profile one can reconstruct an image in the velocity space, which can be converted into a real image if one knows the kinematics of the system. Deux techniques sont couramment utilisées pour obtenir des images des disques dans les systèmes binaires à éclipses. En utilisant la courbe de lumière, on peut remonter à la distribution radiale de la brillance de surface, en supposant que celle-ci a une symètrie axiale. D'autre part, les profils de raies renseignent sur la distribution de vitesse des régions émissives leur variation temporelle permet de réaliser une image dans l'espace des vitesses, que l'on peut ensuite transformer en carte dans l'espace (x,y) si on connaît la cinématique du système.

[Distribution characteristics of particulate mercury in aerosol in coastal city].

PubMed

Zhang, Fu-Wang; Zhao, Jin-Ping; Chen, Jin-Sheng; Xu, Ya

2010-10-01

Particulate mercury, which is bound with aerosol in atmosphere, has a negative impact on human health and the environment, also plays an important role in the biogeochemical process of mercury. In this paper, taking southeast coastal city of Xiamen as research object, the PM2.5, PM10 and TSP were collected in residential, tourism, industrial area and background, respectively, during four seasons (October 2008-September 2009). RA-915 + mercury analyzer was employed to determinate mercury concentration in different size particle matters based on zeeman atomic absorption spectrometry. The results showed that the contents of particulate mercury in different size of aerosol during Winter, Spring were obviously higher than that of Summer, Autumn; the concentrations of particulate mercury in fine particle during Spring, Summer, Autumn and Winter were (51.46 +/- 19.28), (42.41 +/- 12.74), (38.38 +/- 6.08) and (127.23 +/- 33.70) pg/m3, respectively. The experimental data showed that the particulate mercury were mainly distributed in fine particles (PM2.5), which covered 42.48%-67.87%, and it can be concluded that the rate of particulate mercury enrichment in coarse particle was much lower than that of fine particle. The sequence of atmospheric particulate mercury concentration in different functional areas was: background < resident < tourism < industrial area < suburban; which showed characteristics of spatial distribution of particulate mercury was affected by the sampling location. On the whole, Xiamen had a low level of atmospheric particulate mercury; the enrichment of PM2.5 to particulate mercury was significantly higher than that of PM10 and TSP, and showed that fine particle pollution should be tightly controlled to reduce particulate mercury.

Exposure to Particulate Hexavalent Chromium Exacerbates Allergic Asthma Pathology

PubMed Central

Schneider, Brent C.; Constant, Stephanie L.; Patierno, Steven R.; Jurjus, Rosalyn A.; Ceryak, Susan M.

2011-01-01

Airborne hexavalent chromate, Cr(VI), has been identified by the Environmental Protection Agency as a possible health threat in urban areas, due to the carcinogenic potential of some of its forms. Particulate chromates are produced in many different industrial settings, with high levels of aerosolized forms historically documented. Along with an increased risk of lung cancer, a high incidence of allergic asthma has been reported in workers exposed to certain inhaled particulate Cr(VI) compounds. However, a direct causal association between Cr(VI) and allergic asthma has not been established. We recently showed that inhaled particulate Cr(VI) induces an innate neutrophilic inflammatory response in BALB/c mice. In the current studies we investigated how the inflammation induced by inhaled particulate Cr(VI) might alter the pathology of an allergic asthmatic response. We used a well-established mouse model of allergic asthma. Groups of ovalbumin protein (OVA)-primed mice were challenged either with OVA alone, or with a combination of OVA and particulate zinc chromate, and various parameters associated with asthmatic responses were measured. Co-exposure to particulate Cr(VI) and OVA mediated a mixed form of asthma in which both eosinophils and neutrophils are present in airways, tissue pathology is markedly exacerbated, and airway hyperresponsiveness is significantly increased. Taken together these findings suggest that inhalation of particulate forms of Cr(VI) may augment the severity of ongoing allergic asthma, as well as alter its phenotype. Such findings may have implications for asthmatics in settings in which airborne particulate Cr(VI) compounds are present at high levels. PMID:22178736

Ambient air particulates and particulate-bound mercury Hg(p) concentrations: dry deposition study over a Traffic, Airport, Park (T.A.P.) areas during years of 2011-2012.

PubMed

Fang, Guor-Cheng; Lin, Yen-Heng; Zheng, Yu-Cheng

2016-02-01

The main purpose of this study was to monitor ambient air particles and particulate-bound mercury Hg(p) in total suspended particulate (TSP) concentrations and dry deposition at the Hung Kuang (Traffic), Taichung airport and Westing Park sampling sites during the daytime and nighttime, from 2011 to 2012. In addition, the calculated/measured dry deposition flux ratios of ambient air particles and particulate-bound mercury Hg(p) were also studied with Baklanov & Sorensen and the Williams models. For a particle size of 10 μm, the Baklanov & Sorensen model yielded better predictions of dry deposition of ambient air particulates and particulate-bound mercury Hg(p) at the Hung Kuang (Traffic), Taichung airport and Westing Park sampling site during the daytime and nighttime sampling periods. However, for particulates with sizes 20-23 μm, the results obtained in the study reveal that the Williams model provided better prediction results for ambient air particulates and particulate-bound mercury Hg(p) at all sampling sites in this study.

Alternatives to the gravimetric method for quantification of diesel particulate matter near the lower level of detection.

PubMed

Swanson, Jacob; Kittelson, David; Pui, David; Watts, Winthrop

2010-10-01

This paper is part of the Journal of the Air & Waste Management Association's 2010 special issue on combustion aerosol measurements. The issue is a combination of papers that synthesize and evaluate ideas and perspectives that were presented by experts at a series of workshops sponsored by the Coordinating Research Council that aimed to evaluate the current and future status of diesel particulate matter (DPM) measurement. Measurement of DPM is a complex issue with many stakeholders, including air quality management and enforcement agencies, engine manufacturers, health experts, and climatologists. Adoption of the U.S. Environmental Protection Agency 2007 heavy-duty engine DPM standards posed a unique challenge to engine manufacturers. The new standards reduced DPM emissions to the point that improvements to the gravimetric method were required to increase the accuracy and the sensitivity of the measurement. Despite these improvements, the method still has shortcomings. The objectives of this paper are to review the physical and chemical properties of DPM that make gravimetric measurement difficult at very low concentrations and to review alternative metrics and methods that are potentially more accurate, sensitive, and specific. Particle volatility, size, surface area, and number metrics are considered, as well as methods to quantify them. Although the authors believe that an alternative method is required to meet the needs of engine manufacturers, the methods reviewed in the paper are applicable to other areas where the gravimetric method detection limit is approached and greater accuracy and sensitivity are required. The paper concludes by suggesting a method to measure active surface area, combined with a method to separate semi-volatile and solid fractions to further increase the specificity of the measurement, has potential for reducing the lower detection limit of DPM and enabling engine manufacturers to reduce DPM emissions in the future.

Health effects of atmospheric particulates: a medical geology perspective.

PubMed

Duzgoren-Aydin, Nurdan S

2008-01-01

In this review, atmospheric particulates as composite airborne earth materials often containing both natural and anthropogenic components were examined in the context of medical geology. Despite a vast number of both experimental and epidemiological studies confirming the direct and indirect links between atmospheric particulates and human health, the exact nature of mechanisms affecting the particulate-induced pathogenesis largely remains unexplored. Future in depth research on these areas would be most successful if potential mechanisms are examined with reference to the physical (e.g., size, shape and surface), chemical, mineralogical and source characteristics of particulate matters. The underlying goal of this review was to present the relevant terminology and processes proposed in the literature to explain the interfaces and interactions between atmospheric particles and human body within the framework of "atmospheric particle cycles." The complexities of the interactions were demonstrated through case studies focusing on particulate matter air pollution and malignant mesothelioma occurrences due to environmental exposure to erionite-a fibrous zeolite mineral. There is an urgent need for a standard protocol or speciation methods applicable to earth-materials to guide and streamline studies on etiology of mineral-induced diseases. This protocol or speciation methods should provide relevant procedures to determine the level and extent of physical, chemical and mineralogical heterogeneity of particulate matters as well as quantitative in-situ particulate characteristics.

Electrically heated particulate filter enhanced ignition strategy

DOEpatents

Gonze, Eugene V; Paratore, Jr., Michael J

2012-10-23

An exhaust system that processes exhaust generated by an engine is provided. The system generally includes a particulate filter (PF) that filters particulates from the exhaust wherein an upstream end of the PF receives exhaust from the engine. A grid of electrically resistive material is applied to an exterior upstream surface of the PF and selectively heats exhaust passing through the grid to initiate combustion of particulates within the PF. A catalyst coating applied to at least one of the PF and the grid. A control module estimates a temperature of the grid and controls the engine to produce a desired exhaust product to increase the temperature of the grid.

Particulate matter in the Venus atmosphere

NASA Technical Reports Server (NTRS)

Ragent, B.; Esposito, L. W.; Tomasko, M. G.; Marov, M. IA.; Shari, V. P.

1985-01-01

The paper presents a summary of the data currently available (June 1984) describing the planet-enshrouding particulate matter in the Venus atmosphere. A description and discussion of the state of knowledge of the Venus clouds and hazes precedes the tables and plots. The tabular material includes a precis of upper haze and cloud-top properties, parameters for model-size distributions for particles and particulate layers, and columnar masses and mass loadings.

40 CFR 52.275 - Particulate matter control.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 3 2012-07-01 2012-07-01 false Particulate matter control. 52.275 Section 52.275 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS California § 52.275 Particulate matter control. (a) The following rules or portions of rules...

40 CFR 52.275 - Particulate matter control.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 3 2013-07-01 2013-07-01 false Particulate matter control. 52.275 Section 52.275 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS California § 52.275 Particulate matter control. (a) The following rules or portions of rules...

40 CFR 52.275 - Particulate matter control.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 3 2011-07-01 2011-07-01 false Particulate matter control. 52.275 Section 52.275 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS California § 52.275 Particulate matter control. (a) The following rules or portions of rules...

40 CFR 52.275 - Particulate matter control.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 3 2014-07-01 2014-07-01 false Particulate matter control. 52.275 Section 52.275 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS California § 52.275 Particulate matter control. (a) The following rules or portions of rules...

Testing Students' Use of the Particulate Theory

ERIC Educational Resources Information Center

Williamson, Vickie; Huffman, Jason; Peck, Larry

2004-01-01

High School students' understanding about the particulate theory of matter and their use of particulate terminology is investigated. The Physical Changes Concepts Test (PCCT) was administered in two forms, an applied version and a theoretical version, to determine whether students scientifically understood the concepts well enough to apply them to…

Effets perturbateurs endocriniens des pesticides organochlores.

PubMed

Charlier, C; Plomteux, G

2002-01-01

Xenoestrogens such organochlorine pesticides are known to induce changes in reproductive development, function or behaviour in wildlife. Because these compounds are able to modify the estrogens metabolism, or to compete with estradiol for binding to the estrogen receptor, it may be possible that these products affect the risk of developing impaired fertility, precocious puberty or some kinds of cancer in man. Le plus ancien récit de lutte contre la pollution remonte à une légende indienne racontant que la divinité Sing-bonga était incommodée par les émanations des fours dans lesquels les Asuras fondaient leurs métaux (1). Evidemment depuis, la problématique n-a cessé de s-accroître et la contamination de la Terre par de nombreux polluants est devenue aujourd-hui un problème majeur de notre Société. La protection de notre environnement est une question capitale qui doit être respectée malgré la pression économique actuelle et qui ne cessera de croître au cours des prochaines années même si l-identification objective et indiscutable de ce qui est essentiel - donc devant être prioritairement garanti sur la planète - est difficile à cerner (2). « Un oiseau en mauvais état ne pond pas de bons oeufs » disait un proverbe grec. Mais ce n-est qu-à partir de la seconde moitié du XXème siècle que les toxicologues ont commencé à identifier les effets qu-avaient entraînés à l-échelle mondiale les pollutions émises aux XIXème siècle sur la faune sauvage et sur le cheptel (3). L-histoire contemporaine des pesticides industriels commence vers 1874 (synthèse des organochlorés) et se poursuit tout au long de ces 2 siècles en passant par la synthèse des organophosphorés (1950), des carbamates (1970) et des pyréthroïdes (1975) (4). Le dichlorodiphényltrichloroéthane (DDT) a été synthétisé pour la première fois par un étudiant en cours de préparation de sa thèse de doctorat : Othmer Zeidler. La production, reprise par les

THE 1998 BALTIMORE PARTICULATE MATTER EPIDEMIOLOGY-EXPOSURE STUDY: PART 2-PERSONAL EXPOSURE ASSESSMENT ASSOCIATED WITH AN ELDERLY STUDY POPULATION

EPA Science Inventory

An integrated epidemiological-exposure panel study was conducted during the summer of 1998 which focused upon establishing relationships between potential human exposures to particulate matter (PM) and related co-pollutants with detectable health effects. The study design incor...

40 CFR 52.2276 - Control strategy and regulations: Particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

...: Particulate matter. 52.2276 Section 52.2276 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY....2276 Control strategy and regulations: Particulate matter. (a) Part D conditional approval. The Texas... of the fabric filters, Parker Brothers and Co., Inc., shall not emit particulate matter in excess of...

40 CFR 52.1678 - Control strategy and regulations: Particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

...: Particulate matter. 52.1678 Section 52.1678 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... § 52.1678 Control strategy and regulations: Particulate matter. (a)-(c) [Reserved] (d) Section 227.3(a... CFR Subpart G, Control strategy: Sulfur oxides and particulate matter. (e) Determination of Attainment...

PARTICULATE EMISSION CONTROL

EPA Science Inventory

Particle or particulate matter is defined as any finely divided solid or liquid material, other than uncombined water, emitted to the ambient air as measured by applicable reference methods, or an equivalent or alternative method, or by a test method specified in 40CFR50.

Particulate polycyclic aromatic hydrocarbons (PAH) in the atmosphere of Bizerte city, Tunisia.

PubMed

Ben Hassine, S; Hammami, B; Ben Ameur, W; El Megdiche, Y; Barhoumi, B; Driss, M R

2014-09-01

The particle-phase concentrations of polycyclic aromatic hydrocarbons (PAH) were determined in 13 air samples collected in an urban area of Bizerte (Tunisia) during 2009-2010. Atmospheric particulate samples were extracted by ultrasonic bath and analyzed by high-performance liquid chromatography with fluorescence detection. PAH were found in all the analyzed air samples and the most abundant compounds were pyrene, fluoranthene, benzo[g,h,i]perylene, benzo[b]fluoranthene, chrysene and benzo[a]pyrene. ∑14-PAH concentrations ranging from 9.38 to 44.81 ng m(-3) with mean value of 25.39 ng m(-3). PAH diagnostic ratio source analysis revealed gasoline and diesel vehicular emissions as major sources. The mean total benzo[a]pyrene toxicity equivalent calculated for samples was 3.66 ng m(-3) and the mean contribution of the carcinogenic potency of benzo[a]pyrene was determined to be 55.8 %. Concentrations of particulate PAH in Bizerte city atmosphere were approximately eight times greater than sampled at a nearby rural site.

Microfluidics microFACS for Life Detection

NASA Technical Reports Server (NTRS)

Platt, Donald W.; Hoover, Richard B.

2010-01-01

A prototype micro-scale Fluorescent Activated Cell Sorter (microFACS) for life detection has been built and is undergoing testing. A functional miniature microfluidics instrument with the ability to remotely distinguish live or dead bacterial cells from abiotic particulates in ice or permafrost of icy bodies of the solar system would be of fundamental value to NASA. The use of molecular probes to obtain the bio-signature of living or dead cells could answer the most fundamental question of Astrobiology: Does life exist beyond Earth? The live-dead fluorescent stains to be used in the microFACS instrument function only with biological cell walls. The detection of the cell membranes of living or dead bacteria (unlike PAH's and many other Biomarkers) would provide convincing evidence of present or past life. This miniature device rapidly examine large numbers of particulates from a polar ice or permafrost sample and distinguish living from dead bacteria cells and biological cells from mineral grains and abiotic particulates and sort the cells and particulates based on a staining system. Any sample found to exhibit fluorescence consistent with living cells could then be used in conjunction with a chiral labeled release experiment or video microscopy system to seek addition evidence for cellular metabolism or motility. Results of preliminary testing and calibration of the microFACS prototype instrument system with pure cultures and enrichment assemblages of microbial extremophiles will be reported.

40 CFR 52.126 - Control strategy and regulations: Particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

...: Particulate matter. 52.126 Section 52.126 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... strategy and regulations: Particulate matter. (a) The requirements of subpart G and § 51.281 of this... the national standards for particulate matter in Gila, Maricopa, Pima, Pinal, and Santa Cruz Counties...

Identification des parametres du moteur de l'avion Cessna Citation X pour la phase de croisiere a partir des tests en vol et a base des reseaux de neurones =

NASA Astrophysics Data System (ADS)

Zaag, Mahdi

La disponibilite des modeles precis des avions est parmi les elements cles permettant d'assurer leurs ameliorations. Ces modeles servent a ameliorer les commandes de vol et de concevoir de nouveaux systemes aerodynamiques pour la conception des ailes deformables des avions. Ce projet consiste a concevoir un systeme d'identification de certains parametres du modele du moteur de l'avion d'affaires americain Cessna Citation X pour la phase de croisiere a partir des essais en vol. Ces essais ont ete effectues sur le simulateur de vol concu et fabrique par CAE Inc. qui possede le niveau D de la dynamique de vol. En effet, le niveau D est le plus haut niveau de precision donne par l'autorite federale de reglementation FAA de l'aviation civile aux Etats-Unis. Une methodologie basee sur les reseaux de neurones optimises a l'aide d'un algorithme intitule le "grand deluge etendu" est utilisee dans la conception de ce systeme d'identification. Plusieurs tests de vol pour differentes altitudes et differents nombres de Mach ont ete realises afin de s'en servir comme bases de donnees pour l'apprentissage des reseaux de neurones. La validation de ce modele a ete realisee a l'aide des donnees du simulateur. Malgre la nonlinearite et la complexite du systeme, les parametres du moteur ont ete tres bien predits pour une enveloppe de vol determinee. Ce modele estime pourrait etre utilise pour des analyses de fonctionnement du moteur et pourrait assurer le controle de l'avion pendant cette phase de croisiere. L'identification des parametres du moteur pourrait etre realisee aussi pour les autres phases de montee et de descente afin d'obtenir son modele complet pour toute l'enveloppe du vol de l'avion Cessna Citation X (montee, croisiere, descente). Cette methode employee dans ce travail pourrait aussi etre efficace pour realiser un modele pour l'identification des coefficients aerodynamiques du meme avion a partir toujours des essais en vol. None None None

Elaboration de nouvelles approches micromecaniques pour l'optimisation des performances mecaniques des materiaux heterogenes

NASA Astrophysics Data System (ADS)

Aboutajeddine, Ahmed

Les modeles micromecaniques de transition d'echelles qui permettent de determiner les proprietes effectives des materiaux heterogenes a partir de la microstructure sont consideres dans ce travail. L'objectif est la prise en compte de la presence d'une interphase entre la matrice et le renforcement dans les modeles micromecaniques classiques, de meme que la reconsideration des approximations de base de ces modeles, afin de traiter les materiaux multiphasiques. Un nouveau modele micromecanique est alors propose pour tenir compte de la presence d'une interphase elastique mince lors de la determination des proprietes effectives. Ce modele a ete construit grace a l'apport de l'equation integrale, des operateurs interfaciaux de Hill et de la methode de Mori-Tanaka. Les expressions obtenues pour les modules globaux et les champs dans l'enrobage sont de nature analytique. L'approximation de base de ce modele est amelioree par la suite dans un nouveau modele qui s'interesse aux inclusions enrobees avec un enrobage mince ou epais. La resolution utilisee s'appuie sur une double homogeneisation realisee au niveau de l'inclusion enrobee et du materiau. Cette nouvelle demarche, permettra d'apprehender completement les implications des approximations de la modelisation. Les resultats obtenus sont exploites par la suite dans la solution de l'assemblage de Hashin. Ainsi, plusieurs modeles micromecaniques classiques d'origines differentes se voient unifier et rattacher, dans ce travail, a la representation geometrique de Hashin. En plus de pouvoir apprecier completement la pertinence de l'approximation de chaque modele dans cette vision unique, l'extension correcte de ces modeles aux materiaux multiphasiques est rendue possible. Plusieurs modeles analytiques et explicites sont alors proposee suivant des solutions de differents ordres de l'assemblage de Hashin. L'un des modeles explicite apparait comme une correction directe du modele de Mori-Tanaka, dans les cas ou celui ci echoue a

Development of the GC-MS organic aerosol monitor (GC-MS OAM) for in-field detection of particulate organic compounds

NASA Astrophysics Data System (ADS)

Cropper, Paul M.; Overson, Devon K.; Cary, Robert A.; Eatough, Delbert J.; Chow, Judith C.; Hansen, Jaron C.

2017-11-01

Particulate matter (PM) is among the most harmful air pollutants to human health, but due to its complex chemical composition is poorly characterized. A large fraction of PM is composed of organic compounds, but these compounds are not regularly monitored due to limitations in current sampling and analysis techniques. The Organic Aerosol Monitor (GC-MS OAM) combines a collection device with thermal desorption, gas chromatography and mass spectrometry to quantitatively measure the carbonaceous components of PM on an hourly averaged basis. The GC-MS OAM is fully automated and has been successfully deployed in the field. It uses a chemically deactivated filter for collection followed by thermal desorption and GC-MS analysis. Laboratory tests show that detection limits range from 0.2 to 3 ng for 16 atmospherically relevant compounds, with the possibility for hundreds more. The GC-MS OAM was deployed in the field for semi-continuous measurement of the organic markers, levoglucosan, dehydroabietic acid, and polycyclic aromatic hydrocarbons (PAHs) from January to March 2015. Results illustrate the significance of this monitoring technique to characterize the organic components of PM and identify sources of pollution.

Particulate Matter (PM) Pollution

EPA Pesticide Factsheets

Particulate matter (PM) is one of the air pollutants regulated by the National Ambient Air Quality Standards (NAAQS). Reducing emissions of inhalable particles improves public health as well as visibility.

Relation entre les caractéristiques des table-bancs et les mesures anthropométriques des écoliers au Benin

PubMed Central

Falola, Stève Marjelin; Gouthon, Polycarpe; Falola, Jean-Marie; Fiogbe, Michel Armand; Nigan, Issiako Bio

2014-01-01

Introduction Le mobilier scolaire et la posture assise en classe sont souvent impliqués dans l'apparition des douleurs rachidiennes, influant de fait sur la qualité des tâches réalisées par les apprenants. Aucune étude n'a encore vérifié le degré d'adéquation entre les caractéristiques du mobilier et celles des écoliers au Bénin. L'objectif de cette étude transversale est donc de déterminer la relation entre les dimensions des table-bancs utilisées en classe et les mesures anthropométriques des écoliers au Bénin. Methods Elle a été réalisée avec un échantillon probabiliste de 678 écoliers, âgés de 4 à 17 ans. Les mesures anthropométriques des écoliers et les mensurations relatives aux longueurs, largeurs et hauteurs des table-bancs ont été mesurées, puis intégrées aux équations proposées dans la littérature. Les pourcentages des valeurs situées hors des limitesacceptables, dérivées de l'application des équations ont été calculés. Results La largeur et la hauteur des table-bancs utilisées par les écoliers étaient plus élevées (p < 0,05) que les valeurs de référence recommandées par les structures officielles de contrôle et de production des mobiliers scolaires au Bénin. Quel que soit le sexe, il y avait une inadéquation entre la largeur du banc et la longueur fesse-poplité, puis entre la hauteur de la table et la distance coude-bancdes écoliers. Conclusion Les résultats suggèrent de prendre en compte l’évolution des mesures anthropométriques des écoliers dans la confection des table-bancs, afin de promouvoir de bonnes postures assises en classe et de réduire le risque de troubles du rachis. PMID:25317232

Profil épidémiologique des tumeurs malignes primitives des glandes salivaires : à propos de 154 cas

PubMed Central

Setti, Khadija; Mouanis, Mohamed; Moumni, Abdelmounim; Maher, Mostafa; Harmouch, Amal

2014-01-01

Introduction Les tumeurs des glandes salivaires sont des tumeurs rares représentant 3à 5% des tumeurs de la tête et du cou. La classification de l'OMS 2005 distingue les tumeurs épithéliales, les tumeurs mésenchymateuses, les tumeurs hématologiques et les tumeurs secondaires. Méthodes Notre travail consiste en une étude rétrospective réalisée sur une période de 10 ans allant de janvier 2002 à janvier 2012. Les critères d'inclusion étaient: l'âge, le sexe, le siège de la tumeur et le type histologique. Résultats L'incidence annuelle des tumeurs malignes primitives des glandes salivaires dans notre série était de 15 cas par an. Cent cinquante quatre cas de tumeurs malignes primitives des glandes salivaires ont été colligés sans prédominance de sexe (78 femmes (50,6%) et 76 hommes (49,4%)). La moyenne d'âge était de 60 ans avec des extrêmes de 4 et 83 ans et un pic de fréquence entre 51et 70 ans. Deux tiers des cas (65%) avaient une localisation au niveau des glandes principales avec 66 cas au niveau de la parotide (43%) et 34 cas au niveau de la glande sous maxillaire (22%). Cinquante quatre patients avaient une tumeur maligne des glandes salivaires accessoires (35%) dont 61% au niveau du palais. Aucun cas de tumeur maligne de la glande sublinguale n'a été recensé dans notre étude. Le type histologique prédominant dans notre série était le carcinome adénoïde kystique et retrouvé chez 43 patients (27,9%), suivi de l'adénocarcinome sans autre indication chez 37 patients (24%) puis du carcinome mucoépidermoïde chez 16 patients (10,4%) et de l'adénocarcinome polymorphe de bas grade également chez 16 patients (10. 4%). Conclusion Les tumeurs malignes des glandes salivaires représentent un ensemble hétérogène de maladies de caractérisation complexe et de fréquence variable. PMID:25120861

Using XML to encode TMA DES metadata.

PubMed

Lyttleton, Oliver; Wright, Alexander; Treanor, Darren; Lewis, Paul

2011-01-01

The Tissue Microarray Data Exchange Specification (TMA DES) is an XML specification for encoding TMA experiment data. While TMA DES data is encoded in XML, the files that describe its syntax, structure, and semantics are not. The DTD format is used to describe the syntax and structure of TMA DES, and the ISO 11179 format is used to define the semantics of TMA DES. However, XML Schema can be used in place of DTDs, and another XML encoded format, RDF, can be used in place of ISO 11179. Encoding all TMA DES data and metadata in XML would simplify the development and usage of programs which validate and parse TMA DES data. XML Schema has advantages over DTDs such as support for data types, and a more powerful means of specifying constraints on data values. An advantage of RDF encoded in XML over ISO 11179 is that XML defines rules for encoding data, whereas ISO 11179 does not. We created an XML Schema version of the TMA DES DTD. We wrote a program that converted ISO 11179 definitions to RDF encoded in XML, and used it to convert the TMA DES ISO 11179 definitions to RDF. We validated a sample TMA DES XML file that was supplied with the publication that originally specified TMA DES using our XML Schema. We successfully validated the RDF produced by our ISO 11179 converter with the W3C RDF validation service. All TMA DES data could be encoded using XML, which simplifies its processing. XML Schema allows datatypes and valid value ranges to be specified for CDEs, which enables a wider range of error checking to be performed using XML Schemas than could be performed using DTDs.

Using XML to encode TMA DES metadata

PubMed Central

Lyttleton, Oliver; Wright, Alexander; Treanor, Darren; Lewis, Paul

2011-01-01

Background: The Tissue Microarray Data Exchange Specification (TMA DES) is an XML specification for encoding TMA experiment data. While TMA DES data is encoded in XML, the files that describe its syntax, structure, and semantics are not. The DTD format is used to describe the syntax and structure of TMA DES, and the ISO 11179 format is used to define the semantics of TMA DES. However, XML Schema can be used in place of DTDs, and another XML encoded format, RDF, can be used in place of ISO 11179. Encoding all TMA DES data and metadata in XML would simplify the development and usage of programs which validate and parse TMA DES data. XML Schema has advantages over DTDs such as support for data types, and a more powerful means of specifying constraints on data values. An advantage of RDF encoded in XML over ISO 11179 is that XML defines rules for encoding data, whereas ISO 11179 does not. Materials and Methods: We created an XML Schema version of the TMA DES DTD. We wrote a program that converted ISO 11179 definitions to RDF encoded in XML, and used it to convert the TMA DES ISO 11179 definitions to RDF. Results: We validated a sample TMA DES XML file that was supplied with the publication that originally specified TMA DES using our XML Schema. We successfully validated the RDF produced by our ISO 11179 converter with the W3C RDF validation service. Conclusions: All TMA DES data could be encoded using XML, which simplifies its processing. XML Schema allows datatypes and valid value ranges to be specified for CDEs, which enables a wider range of error checking to be performed using XML Schemas than could be performed using DTDs. PMID:21969921

Analysis of the high-temperature particulate collection problem

DOE Office of Scientific and Technical Information (OSTI.GOV)

Razgaitis, R.

1977-10-01

Particulate agglomeration and separation at high temperatures and pressures are examined, with particular emphasis on the unique features of the direct-cycle application of fluidized-bed combustion. The basic long-range mechanisms of aerosol separation are examined, and the effects of high temperature and high pressure on usable collection techniques are assessed. Primary emphasis is placed on those avenues that are not currently attracting widespread research. The high-temperature, particulate-collection problem is surveyed, together with the peculiar requirements associated with operation of turbines with particulate-bearing gas streams. 238 references.

EXPOSURE ASSESSMENT OF OLDER ADULTS TO PARTICULATE MATTER

EPA Science Inventory

The factors that influence the amount of particulate matter that potentially susceptible elderly Americans are exposed to is an issue of concern. This presentation and abstract investigates these factors using data obtained from three longitudinal particulate matter panel studies...

Les soins aux enfants et aux adolescents des familles des militaires canadiens : les considérations particulières

PubMed Central

Rowan-Legg, Anne

2017-01-01

Résumé Les familles des militaires font face à de nombreux facteurs de stress, tels que les réinstallations fréquentes, les longues pério des de séparation familiale, l’isolement géographique du réseau de soutien de la famille élargie et le déploiement en zones très dangereuses. Les enfants et les adolescents des familles des militaires vivent les mêmes trajectoires développementales et motivationnelles que leurs homologues civils, mais ils sont également aux prises avec des pressions et des facteurs de stress liés à leur développement qui sont inhabituels et qui leur sont imposés par les exigences de la vie militaire. Les effets de la vie militaire sur les familles et les enfants commencent à être admis et mieux caractérisés. Il est essentiel de comprendre les préoccupations propres aux enfants et aux adolescents des familles des militaires et de mobiliser les ressources nécessaires pour les soutenir afin de répondre à leurs besoins en matière de santé.

An Automated Heart Rate Detection Platform in Wild-Type Zebrafish for Cardiotoxicity Screening of Fine Particulate Matter Air Pollution

EPA Science Inventory

Exposure to air pollution-derived particulate matter (PM) causes adverse cardiovascular health outcomes, with increasing evidence implicating soluble components of PM; however, the enormous number of unique PM samples from different air sheds far exceeds the capacity of conventio...

Lignes directrices canadiennes sur l’utilisation sécuritaire et efficace des opioïdes pour la douleur chronique non cancéreuse

PubMed Central

Kahan, Meldon; Wilson, Lynn; Mailis-Gagnon, Angela; Srivastava, Anita

2011-01-01

Résumé Objectif Présenter aux médecins de famille un résumé clinique pratique sur la prescription d’opioïdes à des populations particulières en se fondant sur les recommandations faites dans les lignes directrices canadiennes sur l’utilisation sécuritaire et efficace des opioïdes pour la douleur chronique non cancéreuse. Qualité des données Pour produire les lignes directrices, les chercheurs ont effectué une synthèse critique de la littérature médicale en insistant plus précisément sur les études de l’efficacité et de la sécurité des opioïdes dans des populations particulières. Message principal Les médecins de famille peuvent atténuer les risques de surdose, de sédation, d’usage abusif et de dépendance grâce à des stratégies adaptées à l’âge et à l’état de santé des patients. Dans le cas de patients à risque de dépendance, on devrait réserver les opioïdes aux douleurs nociceptives ou neuropathiques bien définies qui n’ont pas répondu aux traitements de première intention. Il faut procéder lentement au titrage des opioïdes, avec des dispensations fréquentes et une étroite surveillance pour dépister tout signe d’usage abusif. Une dépendance aux opioïdes suspectée est prise en charge au moyen d’une thérapie structurée aux opioïdes, d’un traitement à la méthadone ou à la buprénorphine ou encore d’un traitement fondé sur l’abstinence. Les patients souffrant de troubles de l’humeur ou d’anxiété ont tendance à avoir une réponse analgésique atténuée aux opioïdes, sont à risque plus élevé d’usage abusif et prennent souvent des sédatifs qui interagissent défavorablement avec les opioïdes. Il faut prendre des précautions semblables à celles utilisées avec d’autres patients à risque élevé. Il faut faire un sevrage progressif si la douleur du patient demeure sévère même avec un essai adéquat de thérapie aux opioïdes. Chez les personnes âgées, la s

L'astronomie des Anciens

NASA Astrophysics Data System (ADS)

Nazé, Yaël

2009-04-01

Quelle que soit la civilisation à laquelle il appartient, l'être humain cherche dans le ciel des réponses aux questions qu'il se pose sur son origine, son avenir et sa finalité. Le premier mérite de ce livre est de nous rappeler que l'astronomie a commencé ainsi à travers les mythes célestes imaginés par les Anciens pour expliquer l'ordre du monde et la place qu'ils y occupaient. Mais les savoirs astronomiques passés étaient loin d'être négligeables et certainement pas limités aux seuls travaux des Grecs : c'est ce que l'auteur montre à travers une passionnante enquête, de Stonehenge à Gizeh en passant par Pékin et Mexico, fondée sur l'étude des monuments anciens et des sources écrites encore accessibles. Les tablettes mésopotamiennes, les annales chinoises, les chroniques médiévales, etc. sont en outre d'une singulière utilité pour les astronomes modernes : comment sinon remonter aux variations de la durée du jour au cours des siècles, ou percer la nature de l'explosion qui a frappé tant d'observateurs en 1054 ? Ce livre offre un voyage magnifiquement illustré à travers les âges, entre astronomie et archéologie.

Advanced particulate matter control apparatus and methods

DOEpatents

Miller, Stanley J [Grand Forks, ND; Zhuang, Ye [Grand Forks, ND; Almlie, Jay C [East Grand Forks, MN

2012-01-10

Apparatus and methods for collection and removal of particulate matter, including fine particulate matter, from a gas stream, comprising a unique combination of high collection efficiency and ultralow pressure drop across the filter. The apparatus and method utilize simultaneous electrostatic precipitation and membrane filtration of a particular pore size, wherein electrostatic collection and filtration occur on the same surface.

MODELING ENVIRONMENTAL EXPOSURES TO PARTICULATE MATTER AND PESTICIDES

EPA Science Inventory

This presentation describes initial results from on-going research at EPA on modeling human exposures to particulate matter and residential pesticides. A first generation probabilistic population exposure model for Particulate Matter (PM), specifically for predicting PM1o and P...

Microbiota and Particulate Matter Assessment in Portuguese Optical Shops Providing Contact Lens Services

PubMed Central

Viegas, Carla; Faria, Tiago; Pacífico, Cátia; Dos Santos, Mateus; Monteiro, Ana; Lança, Carla; Carolino, Elisabete; Viegas, Susana; Cabo Verde, Sandra

2017-01-01

The aim of this work was to assess the microbiota (fungi and bacteria) and particulate matter in optical shops, contributing to a specific protocol to ensure a proper assessment. Air samples were collected through an impaction method. Surface and equipment swab samples were also collected side-by-side. Measurements of particulate matter were performed using portable direct-reading equipment. A walkthrough survey and checklist was also applied in each shop. Regarding air sampling, eight of the 13 shops analysed were above the legal requirement and 10 from the 26 surfaces samples were overloaded. In three out of the 13 shops fungal contamination in the analysed equipment was not detected. The bacteria air load was above the threshold in one of the 13 analysed shops. However, bacterial counts were detected in all sampled equipment. Fungi and bacteria air load suggested to be influencing all of the other surface and equipment samples. These results reinforce the need to improve air quality, not only to comply with the legal requirements, but also to ensure proper hygienic conditions. Public health intervention is needed to assure the quality and safety of the rooms and equipment in optical shops that perform health interventions in patients. PMID:28505144

Urban tree effects on fine particulate matter and human health

Treesearch

David J. Nowak

2014-01-01

Overall, city trees reduce particulate matter and provide substantial health benefits; but under certain conditions, they can locally increase particulate matter concentrations. Urban foresters need to understand how trees affect particulate matter so they can select proper species and create appropriate designs to improve air quality. This article details trees'...

Electrothermal Vaporization-QQQ-ICP-MS for Determination of Chromium in Mainstream Cigarette Smoke Particulate

PubMed Central

Fresquez, Mark R.; Gonzalez-Jimenez, Nathalie; Gray, Naudia; Valentin-Blasini, Liza; Watson, Clifford H.; Pappas, R. Steven

2017-01-01

Chromium is transported in mainstream tobacco smoke at very low concentrations. However, when chromium is deposited too deeply in the lungs for mucociliary clearance, or is in a particle that is too large to pass directly through tissues, it bioaccumulates in the lungs of smokers. It is important to determine the concentrations of chromium that are transported in mainstream smoke. Several reliable studies have resulted in reports of chromium concentrations in smoke particulate that were below limits of detection for the instruments and methods employed. In this study, electrothermal vaporization-triple quad-inductively coupled plasma-mass spectrometry (ETV-QQQ-ICP-MS) was chosen for determination of chromium concentrations in mainstream smoke because of the high sensitivity of ETV combined with QQQ-ICP-MS. The smoke from five reference, quality control, and commercial cigarettes was analyzed using ETV-QQQ-ICP-MS with isotope dilution for quantitative determination of chromium. The method limit of detection (LOD) was sufficiently low that chromium concentrations in mainstream smoke could indeed be determined. The chromium concentrations in the smoke particulate were between 0.60 and 1.03 ng/cigarette. The range of chromium concentrations was at or below previously reported LODs. Determination of the oxidation state of the chromium transported in mainstream smoke would also be important, in consideration of the fact that both chromium(III) and chromium(VI) oxidation states cause inhalation toxicity, but chromium(VI) is also a carcinogen. It was possible to separate the oxidation states using ETV-QQQ-ICP-MS. However, determination of individual species at the levels found in mainstream smoke particulate matter was not possible with the present method. PMID:28164228

PROCEEDINGS: EIGHTH SYMPOSIUM ON THE TRANSFER AND UTILIZATION OF PARTICULATE CONTROL TECHNOLOGY - VOLUME 2. BAGHOUSES AND PARTICULATE CONTROL FOR NEW APPLICATIONS

EPA Science Inventory

The two-volume proceedings describe the latest research and development efforts to improve particulate control devices, while treating traditional concerns of operational cost and compliance. Overall, particulate control remains a key issue in the cost and applicability of furnac...

Implementation Cryptography Data Encryption Standard (DES) and Triple Data Encryption Standard (3DES) Method in Communication System Based Near Field Communication (NFC)

NASA Astrophysics Data System (ADS)

Ratnadewi; Pramono Adhie, Roy; Hutama, Yonatan; Saleh Ahmar, A.; Setiawan, M. I.

2018-01-01

Cryptography is a method used to create secure communication by manipulating sent messages during the communication occurred so only intended party that can know the content of that messages. Some of the most commonly used cryptography methods to protect sent messages, especially in the form of text, are DES and 3DES cryptography method. This research will explain the DES and 3DES cryptography method and its use for stored data security in smart cards that working in the NFC-based communication system. Several things that will be explained in this research is the ways of working of DES and 3DES cryptography method in doing the protection process of a data and software engineering through the creation of application using C++ programming language to realize and test the performance of DES and 3DES cryptography method in encrypted data writing process to smart cards and decrypted data reading process from smart cards. The execution time of the entering and the reading process data using a smart card DES cryptography method is faster than using 3DES cryptography.

Particulate contamination removal from wafers using plasmas and mechanical agitation

DOEpatents

Selwyn, G.S.

1998-12-15

Particulate contamination removal from wafers is disclosed using plasmas and mechanical agitation. The present invention includes the use of plasmas with mechanical agitation for removing particulate matter from the surface of a wafer. The apparatus hereof comprises a mechanical activator, at least one conducting contact pin for transferring the vibration from the activator to the wafer, clamp fingers that maintain the wafer`s position, and means for generating a plasma in the vicinity of the surface of the wafer, all parts of the cleaning apparatus except the mechanical activator and part of the contact pin being contained inside the processing chamber. By exposing a wafer to a plasma and providing motion thereto in a direction perpendicular to its surface, the bonding between the particulate matter and the surface may be overcome. Once free of the wafer surface, the particulates become charged by electrons from the plasma and are drawn into the plasma by attractive forces which keep them from redepositing. The introduction of a flowing gas through the plasma sweeps the particulates away from the wafer and out of the plasma. The entire surface is cleaned during one cleaning step. The use of an rf plasma to accomplish the particulate removal was found to remove more than 90% of the particulates. 4 figs.

Particulate contamination removal from wafers using plasmas and mechanical agitation

DOEpatents

Selwyn, Gary S.

1998-01-01

Particulate contamination removal from wafers using plasmas and mechanical agitation. The present invention includes the use of plasmas with mechanical agitation for removing particulate matter from the surface of a wafer. The apparatus hereof comprises a mechanical activator, at least one conducting contact pin for transferring the vibration from the activator to the wafer, clamp fingers that maintain the wafer's position, and means for generating a plasma in the vicinity of the surface of the wafer, all parts of the cleaning apparatus except the mechanical activator and part of the contact pin being contained inside the processing chamber. By exposing a wafer to a plasma and providing motion thereto in a direction perpendicular to its surface, the bonding between the particulate matter and the surface may be overcome. Once free of the wafer surface, the particulates become charged by electrons from the plasma and are drawn into the plasma by attractive forces which keep them from redepositing. The introduction of a flowing gas through the plasma sweeps the particulates away from the wafer and out of the plasma. The entire surface is cleaned during one cleaning step. The use of an rf plasma to accomplish the particulate removal was found to remove more than 90% of the particulates.

40 CFR 52.2429 - Control strategy: Particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 4 2011-07-01 2011-07-01 false Control strategy: Particulate matter. 52.2429 Section 52.2429 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: Particulate matter. Determination of Attainment. EPA has determined, as of January 12...

40 CFR 52.477 - Control strategy: Particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 3 2014-07-01 2014-07-01 false Control strategy: Particulate matter. 52.477 Section 52.477 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: Particulate matter. Determination of Attainment. EPA has determined, as of January 12...

40 CFR 52.477 - Control strategy: Particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 3 2013-07-01 2013-07-01 false Control strategy: Particulate matter. 52.477 Section 52.477 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: Particulate matter. Determination of Attainment. EPA has determined, as of January 12...

40 CFR 52.1081 - Control strategy: Particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 4 2013-07-01 2013-07-01 false Control strategy: Particulate matter. 52.1081 Section 52.1081 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: Particulate matter. (a) Determination of Attainment. EPA has determined, as of January...

40 CFR 52.2429 - Control strategy: Particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 5 2013-07-01 2013-07-01 false Control strategy: Particulate matter. 52.2429 Section 52.2429 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: Particulate matter. Determination of Attainment. EPA has determined, as of January 12...

40 CFR 52.1131 - Control strategy: Particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 4 2011-07-01 2011-07-01 false Control strategy: Particulate matter. 52.1131 Section 52.1131 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: Particulate matter. (a) Revisions to the following regulations submitted on March 30...

40 CFR 52.1131 - Control strategy: Particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control strategy: Particulate matter. 52.1131 Section 52.1131 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: Particulate matter. (a) Revisions to the following regulations submitted on March 30...

40 CFR 52.477 - Control strategy: Particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 3 2012-07-01 2012-07-01 false Control strategy: Particulate matter. 52.477 Section 52.477 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: Particulate matter. Determination of Attainment. EPA has determined, as of January 12...

40 CFR 52.1081 - Control strategy: Particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 4 2012-07-01 2012-07-01 false Control strategy: Particulate matter. 52.1081 Section 52.1081 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: Particulate matter. (a) Determination of Attainment. EPA has determined, as of January...

40 CFR 52.2429 - Control strategy: Particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 5 2012-07-01 2012-07-01 false Control strategy: Particulate matter. 52.2429 Section 52.2429 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: Particulate matter. Determination of Attainment. EPA has determined, as of January 12...

40 CFR 52.1131 - Control strategy: Particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 4 2012-07-01 2012-07-01 false Control strategy: Particulate matter. 52.1131 Section 52.1131 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: Particulate matter. (a) Revisions to the following regulations submitted on March 30...

40 CFR 52.477 - Control strategy: Particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 3 2011-07-01 2011-07-01 false Control strategy: Particulate matter. 52.477 Section 52.477 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: Particulate matter. Determination of Attainment. EPA has determined, as of January 12...

40 CFR 52.1081 - Control strategy: Particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 4 2011-07-01 2011-07-01 false Control strategy: Particulate matter. 52.1081 Section 52.1081 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: Particulate matter. (a) Determination of Attainment. EPA has determined, as of January...

40 CFR 52.1081 - Control strategy: Particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 4 2014-07-01 2014-07-01 false Control strategy: Particulate matter. 52.1081 Section 52.1081 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: Particulate matter. (a) Determination of Attainment. EPA has determined, as of January...

40 CFR 52.2429 - Control strategy: Particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 5 2014-07-01 2014-07-01 false Control strategy: Particulate matter. 52.2429 Section 52.2429 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: Particulate matter. Determination of Attainment. EPA has determined, as of January 12...

40 CFR 52.1081 - Control strategy: Particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control strategy: Particulate matter. 52.1081 Section 52.1081 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: Particulate matter. (a) Determination of Attainment. EPA has determined, as of January...

40 CFR 52.2429 - Control strategy: Particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control strategy: Particulate matter. 52.2429 Section 52.2429 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: Particulate matter. Determination of Attainment. EPA has determined, as of January 12...

40 CFR 52.477 - Control strategy: Particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 3 2010-07-01 2010-07-01 false Control strategy: Particulate matter. 52.477 Section 52.477 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: Particulate matter. Determination of Attainment. EPA has determined, as of January 12...

Measuring Diversity and Inclusion in Academic Medicine: The Diversity Engagement Survey (DES)

PubMed Central

Person, Sharina D.; Jordan, C. Greer; Allison, Jeroan J.; Fink Ogawa, Lisa M.; Castillo-Page, Laura; Conrad, Sarah; Nivet, Marc A.; Plummer, Deborah L.

2018-01-01

Purpose To produce a physician and scientific workforce capable of delivering high quality, culturally competent health care and research, academic medical centers must assess their capacity for diversity and inclusion and respond to identified opportunities. Thus, the Diversity Engagement Survey (DES) is presented as a diagnostic and benchmarking tool. Method The 22-item DES connects workforce engagement theory with inclusion and diversity constructs. Face and content validity were established based on decades of previous work to promote institutional diversity. The survey was pilot tested at a single academic medical center and subsequently administered at 13 additional academic medical centers. Cronbach alphas assessed internal consistency and Confirmatory Factor Analysis (CFA) established construct validity. Criterion validity was assessed by observed separation in scores for groups traditionally recognized to have less workforce engagement. Results The sample consisted of 13,694 individuals at 14 medical schools from across the U.S. who responded to the survey administered between 2011– 2012. The Cronbach alphas for inclusion and engagement factors (range: 0.68 to 0.85), CFA fit indices, and item correlations with latent constructs, indicated an acceptable model fit and that questions measured the intended concepts. DES scores clearly distinguished higher and lower performing institutions. The DES detected important disparities for black, women, and those who did not have heterosexual orientation. Conclusions This study demonstrated that the DES is a reliable and valid instrument for internal assessment and evaluation or external benchmarking of institutional progress in building inclusion and engagement. PMID:26466376

An economic passive sampling method to detect particulate pollutants using magnetic measurements.

PubMed

Cao, Liwan; Appel, Erwin; Hu, Shouyun; Ma, Mingming

2015-10-01

Identifying particulate matter (PM) emitted from industrial processes into the atmosphere is an important issue in environmental research. This paper presents a passive sampling method using simple artificial samplers that maintains the advantage of bio-monitoring, but overcomes some of its disadvantages. The samplers were tested in a heavily polluted area (Linfen, China) and compared to results from leaf samples. Spatial variations of magnetic susceptibility from artificial passive samplers and leaf samples show very similar patterns. Scanning electron microscopy suggests that the collected PM are mostly in the range of 2-25 μm; frequent occurrence of spherical shape indicates industrial combustion dominates PM emission. Magnetic properties around power plants show different features than other plants. This sampling method provides a suitable and economic tool for semi-quantifying temporal and spatial distribution of air quality; they can be installed in a regular grid and calibrate the weight of PM. Copyright © 2015 Elsevier Ltd. All rights reserved.

Modeling particulate matter emissions during mineral loading process under weak wind simulation.

PubMed

Zhang, Xiaochun; Chen, Weiping; Ma, Chun; Zhan, Shuifen

2013-04-01

The quantification of particulate matter emissions from mineral handling is an important problem for the quantification of global emissions on industrial sites. Mineral particulate matter emissions could adversely impact environmental quality in mining regions, transport regions, and even on a global scale. Mineral loading is an important process contributing to mineral particulate matter emissions, especially under weak wind conditions. Mathematical models are effective ways to evaluate particulate matter emissions during the mineral loading process. The currently used empirical models based on the form of a power function do not predict particulate matter emissions accurately under weak wind conditions. At low particulate matter emissions, the models overestimated, and at high particulate matter emissions, the models underestimated emission factors. We conducted wind tunnel experiments to evaluate the particulate matter emission factors for the mineral loading process. A new approach based on the mathematical form of a logistical function was developed and tested. It provided a realistic depiction of the particulate matter emissions during the mineral loading process, accounting for fractions of fine mineral particles, dropping height, and wind velocity. Copyright © 2013 Elsevier B.V. All rights reserved.

Domestic smoke exposure is associated with alveolar macrophage particulate load.

PubMed

Fullerton, Duncan G; Jere, Khuzwayo; Jambo, Kondwani; Kulkarni, Neeta S; Zijlstra, Eduard E; Grigg, Jonathan; French, Neil; Molyneux, Malcolm E; Gordon, Stephen B

2009-03-01

Indoor air pollution is associated with impaired respiratory health. The pre-dominant indoor air pollutant to which two billion of the world's population is exposed is biomass fuel smoke. We tested the hypothesis that reported smoke exposure in men and women is associated with increased alveolar macrophage uptake of biomass smoke particulates. Healthy volunteers attending for research bronchoscopy in Malawi completed a questionnaire assessment of smoke exposure. Particulate matter visible in alveolar macrophages (AM) was quantified using digital image analysis. The geometric mean of the percentage area of the cytoplasm occupied by particulates in 50 cover-slip adherent AM was calculated and termed particulate load. In 57 subjects (40 men and 17 women) there was a significant difference between the particulate load in groups divided according to pre-dominant lighting form used at home (ANOVA P = 0.0009) and type of cooking fuel (P = 0.0078). Particulate load observed in macrophages is associated with the reported type of biomass fuel exposure. Macrophage function in relation to respiratory health should now be investigated in biomass smoke exposed subjects.

Method for dispersing catalyst onto particulate material

DOEpatents

Utz, Bruce R.; Cugini, Anthony V.

1992-01-01

A method for dispersing finely divided catalyst precursors onto the surface of coal or other particulate material includes the steps of forming a wet paste mixture of the particulate material and a liquid solution containing a dissolved transition metal salt, for instance a solution of ferric nitrate. The wet paste mixture is in a state of incipient wetness with all of this solution adsorbed onto the surfaces of the particulate material without the presence of free moisture. On adding a precipitating agent such as ammonia, a catalyst precursor such as hydrated iron oxide is deposited on the surfaces of the coal. The catalyst is activated by converting it to the sulfide form for the hydrogenation or direct liquefaction of the coal.

40 CFR 52.2526 - Control strategy: Particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 4 2011-07-01 2011-07-01 false Control strategy: Particulate matter. 52.2526 Section 52.2526 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: Particulate matter. (a) EPA approves West Virginia's November 15, 1991 SIP submittal for...

40 CFR 52.1374 - Control strategy: Particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 4 2011-07-01 2011-07-01 false Control strategy: Particulate matter. 52.1374 Section 52.1374 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: Particulate matter. (a) On July 8, 1997, the Governor of Montana submitted minor...

40 CFR 52.1025 - Control strategy: Particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 4 2011-07-01 2011-07-01 false Control strategy: Particulate matter. 52.1025 Section 52.1025 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... strategy: Particulate matter. (a) The revisions to the control strategy resulting from the modification to...

40 CFR 52.1374 - Control strategy: Particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 4 2014-07-01 2014-07-01 false Control strategy: Particulate matter. 52.1374 Section 52.1374 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: Particulate matter. (a) On July 8, 1997, the Governor of Montana submitted minor...

40 CFR 52.1374 - Control strategy: Particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 4 2013-07-01 2013-07-01 false Control strategy: Particulate matter. 52.1374 Section 52.1374 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: Particulate matter. (a) On July 8, 1997, the Governor of Montana submitted minor...

40 CFR 52.1341 - Control strategy: particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 4 2011-07-01 2011-07-01 false Control strategy: particulate matter. 52.1341 Section 52.1341 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: particulate matter. Determination of Attainment. EPA has determined, as of May 23, 2011...

40 CFR 52.2526 - Control strategy: Particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 5 2012-07-01 2012-07-01 false Control strategy: Particulate matter. 52.2526 Section 52.2526 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: Particulate matter. (a) EPA approves West Virginia's November 15, 1991 SIP submittal for...

40 CFR 52.1025 - Control strategy: Particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 4 2012-07-01 2012-07-01 false Control strategy: Particulate matter. 52.1025 Section 52.1025 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... strategy: Particulate matter. (a) The revisions to the control strategy resulting from the modification to...

40 CFR 52.2526 - Control strategy: Particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 5 2013-07-01 2013-07-01 false Control strategy: Particulate matter. 52.2526 Section 52.2526 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: Particulate matter. (a) EPA approves West Virginia's November 15, 1991 SIP submittal for...

40 CFR 52.2526 - Control strategy: Particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 5 2014-07-01 2014-07-01 false Control strategy: Particulate matter. 52.2526 Section 52.2526 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: Particulate matter. (a) EPA approves West Virginia's November 15, 1991 SIP submittal for...

40 CFR 52.1374 - Control strategy: Particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 4 2012-07-01 2012-07-01 false Control strategy: Particulate matter. 52.1374 Section 52.1374 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: Particulate matter. (a) On July 8, 1997, the Governor of Montana submitted minor...

40 CFR 52.1374 - Control strategy: Particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control strategy: Particulate matter. 52.1374 Section 52.1374 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: Particulate matter. (a) On July 8, 1997, the Governor of Montana submitted minor...

40 CFR 52.1025 - Control strategy: Particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 4 2013-07-01 2013-07-01 false Control strategy: Particulate matter. 52.1025 Section 52.1025 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... strategy: Particulate matter. (a) The revisions to the control strategy resulting from the modification to...

40 CFR 52.1341 - Control strategy: particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 4 2012-07-01 2012-07-01 false Control strategy: particulate matter. 52.1341 Section 52.1341 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: particulate matter. Determination of Attainment. EPA has determined, as of May 23, 2011...

40 CFR 52.1025 - Control strategy: Particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 4 2014-07-01 2014-07-01 false Control strategy: Particulate matter. 52.1025 Section 52.1025 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... strategy: Particulate matter. (a) The revisions to the control strategy resulting from the modification to...

40 CFR 52.2526 - Control strategy: Particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control strategy: Particulate matter. 52.2526 Section 52.2526 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Control strategy: Particulate matter. (a) EPA approves West Virginia's November 15, 1991 SIP submittal for...

Search for the Higgs Boson and for Anomalous Quartic Gauge Boson Couplings in the WW Channel with Dielectron Events with the D0 Experiment at the Tevatron; Recherche du boson de Higgs et de couplages de jauge quartiques anormaux dans le canal WW en électrons dans l'expérience D0 au Tevatron (in French)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chapon, Emilien

Le paysage de la physique des particules a subi des changements majeurs entre le début de cette thèse, en septembre 2010, et sa n en juin 2013. On peut notamment qualier l'année 2012 de date-clé dans l'histoire de la physique des particules. En 2012, une nouvelle particule a été découverte au LHC [1, 2], dont la majeure partie de la communauté s'accorde aujourd'hui à dire qu'il s'agit très probablement du boson de Higgs. Cet événement est intervenu peu après une sorte de passage de relais entre le Tevatron, arrêté le 30 septembre 2011, et le LHC, dont les toutes premièresmore » collisions sont intervenues le 23 novembre 2009.« less

South African Particulates

Atmospheric Science Data Center

2013-04-16

article title:  Airborne Particulates over Southern Africa ... correspond to places where a result was not obtained, for example, due to the presence of clouds. Extensive burning of grass and ... MD. The MISR data were obtained from the NASA Langley Research Center Atmospheric Science Data Center in Hampton, VA. Image ...

Self-Cleaning Particulate Prefilter Media

NASA Technical Reports Server (NTRS)

Weber, Olivia; Lalwani, San-jiv; Sharma, Anjal

2012-01-01

A long-term space mission requires efficient air revitalization performance to sustain the crew. Prefilter and particulate air filter media are susceptible to rapid fouling that adversely affects their performance and can lead to catastrophic failure of the air revitalization system, which may result in mission failure. For a long-term voyage, it is impractical to carry replacement particulate prefilter and filter modules due to the usual limitations in size, volume, and weight. The only solution to this problem is to reagentlessly regenerate prefilter and filter media in place. A method was developed to modify the particulate prefilter media to allow them to regenerate reagentlessly, and in place, by the application of modest thermocycled transverse or reversed airflows. The innovation may allow NASA to close the breathing air loop more efficiently, thereby sustaining the vision for manned space exploration missions of the future. A novel, self-cleaning coatings technology was developed for air filter media surfaces that allows reagentless in-place regeneration of the surface. The technology grafts thermoresponsive and nonspecific adhesion minimizing polymer nanolayer brush coatings from the prefilter media. These polymer nanolayer brush architectures can be triggered to contract and expand to generate a "pushing-off" force by the simple application of modestly thermocycled (i.e. cycling from ambient cabin temperature to 40 C) air streams. The nonspecific adhesion-minimizing properties of the coatings do not allow the particulate foulants to adhere strongly to the filter media, and thermocycled air streams applied to the media allow easy detachment and in-place regeneration of the media with minimal impact in system downtime or astronaut involvement in overseeing the process.

Relations de Dispersion et Diffusion des Glueballs et des Mesons dans la Theorie de Jauge U(1)(2+1) Compacte

NASA Astrophysics Data System (ADS)

Ahmed, Chaara El Mouez

Nous avons etudie les relations de dispersion et la diffusion des glueballs et des mesons dans le modele U(1)_{2+1} compact. Ce modele a ete souvent utilise comme un simple modele de la chromodynamique quantique (QCD), parce qu'il possede le confinement ainsi que les etats de glueballs. Par contre, sa structure mathematique est beaucoup plus simple que la QCD. Notre methode consiste a diagonaliser l'Hamiltonien de ce modele dans une base appropriee de graphes et sur reseau impulsion, afin de generer les relations de dispersion des glueballs et des mesons. Pour la diffusion, nous avons utilise la methode dependante du temps pour calculer la matrice S et la section efficace de diffusion des glueballs et des mesons. Les divers resultats obtenus semblent etre en accord avec les travaux anterieurs de Hakim, Alessandrini et al., Irving et al., qui eux, utilisent plutot la theorie des perturbations en couplage fort, et travaillent sur un reseau espace-temps.

40 CFR 52.427 - Control strategy: Particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 3 2012-07-01 2012-07-01 false Control strategy: Particulate matter. 52.427 Section 52.427 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR...: Particulate matter. Determination of attainment. EPA has determined, as of May 16, 2012, that based on 2007 to...

40 CFR 52.332 - Control strategy: Particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 3 2011-07-01 2011-07-01 false Control strategy: Particulate matter. 52.332 Section 52.332 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR...: Particulate matter. (a) On April 9, 1992, the Governor of Colorado submitted the moderate PM-10 nonattainment...

40 CFR 52.332 - Control strategy: Particulate matter.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 3 2014-07-01 2014-07-01 false Control strategy: Particulate matter. 52.332 Section 52.332 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR...: Particulate matter. (a) On April 9, 1992, the Governor of Colorado submitted the moderate PM-10 nonattainment...

40 CFR 52.332 - Control strategy: Particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 3 2013-07-01 2013-07-01 false Control strategy: Particulate matter. 52.332 Section 52.332 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR...: Particulate matter. (a) On April 9, 1992, the Governor of Colorado submitted the moderate PM-10 nonattainment...

40 CFR 52.332 - Control strategy: Particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 3 2012-07-01 2012-07-01 false Control strategy: Particulate matter. 52.332 Section 52.332 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR...: Particulate matter. (a) On April 9, 1992, the Governor of Colorado submitted the moderate PM-10 nonattainment...

40 CFR 52.332 - Control strategy: Particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 3 2010-07-01 2010-07-01 false Control strategy: Particulate matter. 52.332 Section 52.332 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR...: Particulate matter. (a) On April 9, 1992, the Governor of Colorado submitted the moderate PM-10 nonattainment...

Evaluation d’une grille de supervision des laboratoires des leishmanioses cutanées au Maroc

PubMed Central

El Mansouri, Bouchra; Amarir, Fatima; Hajli, Yamina; Fellah, Hajiba; Sebti, Faiza; Delouane, Bouchra; Sadak, Abderrahim; Adlaoui, El Bachir; Rhajaoui, Mohammed

2017-01-01

Introduction Afin d’évaluer une grille de contrôle standardisée de laboratoire de diagnostic des leishmanioses, comme nouveau outil de supervision. Méthodes Un essai pilote a été pratiqué sur sept laboratoires provinciaux, appartenant à quatre provinces au Maroc, en suivant l’évolution de leurs performances tous les deux ans, entre l’année 2006 et 2014. Cette étude détaille la situation des laboratoires provinciaux avant et après la mise en œuvre de la grille de supervision. Au total vingt et une grille sont analysées. Résultats En 2006, les résultats ont montré clairement une insuffisance des performances des laboratoires: besoin en formation (41.6%), personnel pratiquant le prélèvement cutané (25%), pénurie en matériels et réactifs (65%), gestions documentaire et local non conformes (85%). Différentes actions correctives ont été menées par le Laboratoire National de Référence des Leishmanioses (LNRL) durant la période d’étude. En 2014, le LNRL a enregistré une nette amélioration des performances des laboratoires. Les besoins en matière de formation, qualité du prélèvement, dotation en matériels et réactifs ont été comblés et une coordination efficace s’est établie entre le LNRL et les laboratoires provinciaux. Conclusion Ceci montre l'efficacité de la grille comme outil de supervision de grande qualité, et comme pierre angulaire de tout progrès qui doit être obtenu dans les programmes de lutte contre les leishmanioses. PMID:29187922

Identification et prise en charge des femmes ayant des antécédents familiaux de cancer du sein

PubMed Central

Heisey, Ruth; Carroll, June C.

2016-01-01

Résumé Objectif Résumer les meilleures données portant sur les stratégies d’identification et de prise en charge des femmes qui présentent des antécédents familiaux de cancer du sein. Sources d’information Une recherche a été effectuée sur PubMed à l’aide des mots-clés anglais suivants : breast cancer, guidelines, risk, family history, management et magnetic resonance imaging screening, entre 2000 et 2016. La plupart des données sont de niveau II. Message principal Une bonne anamnèse familiale est essentielle lors de l’évaluation du risque de cancer du sein afin d’identifier les femmes qui sont candidates à une recommandation en counseling génétique pour un éventuel test génétique. On peut sauver des vies en offrant aux femmes porteuses d’une mutation au gène BRCA des interventions chirurgicales de réduction des risques (mastectomie bilatérale prophylactique, salpingo-ovariectomie bilatérale). Il faut encourager toutes les femmes qui présentent des antécédents familiaux de cancer du sein à demeurer actives et à limiter leur consommation d’alcool à moins de 1 verre par jour; certaines femmes sont admissibles à la chimioprévention. Il faut offrir aux femmes dont le risque à vie de cancer du sein est de 20 à 25 % ou plus un dépistage poussé par imagerie par résonance magnétique en plus d’une mammographie. Conclusion Une vie saine et la chimioprévention (chez les candidates) pourraient réduire l’incidence du cancer du sein; le dépistage poussé pourrait entraîner une détection plus précoce. Le fait d’aiguiller des femmes porteuses d’une mutation au BRCA vers la chirurgie de réduction des risques sauve des vies. PMID:27737991

Frontal Affinity Chromatography with Mass Spectrometry Detection for Probing Molecular Interactions. A New Mechanistic Approach for the Development of Detection & Identification and Medical Countermeasures Against CB Agents

DTIC Science & Technology

2005-10-01

l’optimisation des composants les plus prometteurs pour la d~couverte des m~dicaments. La technique CAF-SM est capable de localiser et de caract~riser...technique d’avant-garde peut ainsi aiguiller ]a recherche biotechnologique A travers les domaines cl~s et 6liminer beaucoup d’ann6es d’exp6rimentation...A l’aveuglette »). Ceci permettra de rationaliser le concept et la mise au point dans des domaines tels que la bio- detection et l’identification

Particulate emissions from diesel engines: correlation between engine technology and emissions

PubMed Central

2014-01-01

In the last 30 years, diesel engines have made rapid progress to increased efficiency, environmental protection and comfort for both light- and heavy-duty applications. The technical developments include all issues from fuel to combustion process to exhaust gas aftertreatment. This paper provides a comprehensive summary of the available literature regarding technical developments and their impact on the reduction of pollutant emission. This includes emission legislation, fuel quality, diesel engine- and exhaust gas aftertreatment technologies, as well as particulate composition, with a focus on the mass-related particulate emission of on-road vehicle applications. Diesel engine technologies representative of real-world on-road applications will be highlighted. Internal engine modifications now make it possible to minimize particulate and nitrogen oxide emissions with nearly no reduction in power. Among these modifications are cooled exhaust gas recirculation, optimized injections systems, adapted charging systems and optimized combustion processes with high turbulence. With introduction and optimization of exhaust gas aftertreatment systems, such as the diesel oxidation catalyst and the diesel particulate trap, as well as NOx-reduction systems, pollutant emissions have been significantly decreased. Today, sulfur poisoning of diesel oxidation catalysts is no longer considered a problem due to the low-sulfur fuel used in Europe. In the future, there will be an increased use of bio-fuels, which generally have a positive impact on the particulate emissions and do not increase the particle number emissions. Since the introduction of the EU emissions legislation, all emission limits have been reduced by over 90%. Further steps can be expected in the future. Retrospectively, the particulate emissions of modern diesel engines with respect to quality and quantity cannot be compared with those of older engines. Internal engine modifications lead to a clear reduction of the

Particulate emissions from diesel engines: correlation between engine technology and emissions.

PubMed

Fiebig, Michael; Wiartalla, Andreas; Holderbaum, Bastian; Kiesow, Sebastian

2014-03-07

In the last 30 years, diesel engines have made rapid progress to increased efficiency, environmental protection and comfort for both light- and heavy-duty applications. The technical developments include all issues from fuel to combustion process to exhaust gas aftertreatment. This paper provides a comprehensive summary of the available literature regarding technical developments and their impact on the reduction of pollutant emission. This includes emission legislation, fuel quality, diesel engine- and exhaust gas aftertreatment technologies, as well as particulate composition, with a focus on the mass-related particulate emission of on-road vehicle applications. Diesel engine technologies representative of real-world on-road applications will be highlighted.Internal engine modifications now make it possible to minimize particulate and nitrogen oxide emissions with nearly no reduction in power. Among these modifications are cooled exhaust gas recirculation, optimized injections systems, adapted charging systems and optimized combustion processes with high turbulence. With introduction and optimization of exhaust gas aftertreatment systems, such as the diesel oxidation catalyst and the diesel particulate trap, as well as NOx-reduction systems, pollutant emissions have been significantly decreased. Today, sulfur poisoning of diesel oxidation catalysts is no longer considered a problem due to the low-sulfur fuel used in Europe. In the future, there will be an increased use of bio-fuels, which generally have a positive impact on the particulate emissions and do not increase the particle number emissions.Since the introduction of the EU emissions legislation, all emission limits have been reduced by over 90%. Further steps can be expected in the future. Retrospectively, the particulate emissions of modern diesel engines with respect to quality and quantity cannot be compared with those of older engines. Internal engine modifications lead to a clear reduction of the

Chemical composition of submicron and fine particulate matter collected in Krakow, Poland. Consequences for the APARIC project.

PubMed

Samek, Lucyna; Furman, Leszek; Mikrut, Magdalena; Regiel-Futyra, Anna; Macyk, Wojciech; Stochel, Grażyna; van Eldik, Rudi

2017-11-01

Submicron particulate matter containing particles with an aerodynamic diameter ≤1 μm (PM1) are not monitored continuously by Environmental Protection Agencies around the World and are seldom studied. Numerous studies have indicated that people exposed to ultrafine (≤100 nm), submicron and fine particulate matter containing particles with an aerodynamic diameter ≤2.5 μm (PM2.5), can suffer from respiratory track diseases, cardiovascular, immunological or heart diseases and others. Inorganic pollutants containing redox active transition metals and small gaseous molecules, are involved in the generation of reactive oxygen and reactive nitrogen species. Inhalation of this kind of particles can affect immune-toxicity. Environmental pollution may aggravate the course of autoimmune diseases, in particular influence the mechanisms of the autoimmune system. Important factors that influence the toxicity of particulate matter, are particle size distribution, composition and concentration. This report deals with the composition of PM1 and PM2.5 fractions collected in Krakow, Poland. In spring 2015, the mean concentrations of PM1 and PM2.5 were 19 ± 14 and 27 ± 19 μg/m 3 , respectively. The PM2.5 fraction contained approximately 70 ± 17% of submicron particulate matter. In spring 2016, the mean concentrations of PM1 and PM2.5 were 12 ± 5 and 22 ± 12 μg/m 3 , respectively. The PM2.5 fraction contained approximately 60 ± 15% of submicron particulate matter. The concentrations of the elements Cl, K, Ca, Ti, Cr, Mn, Fe, Ni, Cu, Zn, Br, Rb, Sr and Pb in both fractions were determined by X-ray fluorescence spectrometry. Most of the analyzed metals had higher concentrations in the fine fraction than in the submicron one. Concentrations of V and As were below the detection limit in both fractions, whereas concentrations of Mn and Ca were below the detection limits in the PM1 fraction. The results are discussed in terms of the consequences they may have on

40 CFR 52.228 - Regulations: Particulate matter, Southeast Desert Intrastate Region.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 3 2010-07-01 2010-07-01 false Regulations: Particulate matter... § 52.228 Regulations: Particulate matter, Southeast Desert Intrastate Region. (a) The following... particulate matter in the Southeast Desert Intrastate Region. (1) Imperial County Air Pollution Control...

40 CFR 52.228 - Regulations: Particulate matter, Southeast Desert Intrastate Region.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 3 2011-07-01 2011-07-01 false Regulations: Particulate matter... § 52.228 Regulations: Particulate matter, Southeast Desert Intrastate Region. (a) The following... particulate matter in the Southeast Desert Intrastate Region. (1) Imperial County Air Pollution Control...

Particulate Matter Filtration Design Considerations for Crewed Spacecraft Life Support Systems

NASA Technical Reports Server (NTRS)

Agui, Juan H.; Vijayakumar, R.; Perry, Jay L.

2016-01-01

Particulate matter filtration is a key component of crewed spacecraft cabin ventilation and life support system (LSS) architectures. The basic particulate matter filtration functional requirements as they relate to an exploration vehicle LSS architecture are presented. Particulate matter filtration concepts are reviewed and design considerations are discussed. A concept for a particulate matter filtration architecture suitable for exploration missions is presented. The conceptual architecture considers the results from developmental work and incorporates best practice design considerations.

Note des Éditeurs scientifiques

NASA Astrophysics Data System (ADS)

Averbuch, P.

Cette série d'articles est une revue de résultats expérimentaux sur différents "fluides" moléculaires, dans lesquels la cohésion est due à des forces de Van der Waals et à des liaisons hydrogène, l'eau étant un de ces fluides. Ces résultats sont présentés de façon à justifier expérimentalement un modèle original, non extensif, des propriétés de ces fluides, et l'ensemble se présente sous la forme de trois articles décrivant le modèle, suivis chacun par un article le comparant aux résultats expérimentaux publiés par de nombreux auteurs. Le caractère non extensif des propriétés physiques des fluides est choquant, contraire à beaucoup d'idées établies, il semble n'avoir en sa faveur qu'un argument, la comparaison avec un nombre de résultats expérimentaux assez grand pour que l'effet du hasard soit difficilement soupçonnable. En particulier, les écarts entre des résultats de mesures faits par des auteurs différents dans des conditions différentes sont expliqués, le sérieux et la compétence des différents expérimentateurs ne sont plus mis en doute : mais l'interprétation de ces résultats avec un modèle extensif non adapté est seule mise en cause. Les modèles extensifs étant utilisés systématiquement, au delà des expériences de physiciens, dans les calculs d'ingénieurs, et dans la modélisation d'appareils qui fonctionnent et de phénomènes naturels observés par tout le monde, il fallait expliquer pourquoi on pouvait renoncer à l'extensivité. Les raisons du succès pratique des modèles extensifs sont données, d'abord dans le cas des nématiques, puis dans celui des liquides ordinaires, et c'est ce qui rend l'ensemble cohérent, tant avec les mesures physiques fines qu'avec les observations quotidiennes. Il n'en reste pas moins que si l'interprétation donnée dans cette série d'articles est généralisable, une justification théorique du modèle utilisé devient nécessaire. Pour ce qui est des propriétés d

Applications of Composite Materials in Helicopter Construction (Les Applications des Materiaux Composite dans la Construction des Helicopteres),

DTIC Science & Technology

1983-11-21

TRANSLATION TITLE: APPLICATIONS OF COMPOSITE MATERIALS IN HELICOPTER CONSTRUCTION LES APPLICATIONS DES MATERTAUX COMWSITE DANS LA CONSTRUCTION DES...International Symposium on Design and Use of Kevlar in Aircraft, Geneva, 12 October 1982 [Beziac, Gilbert;* Les applications des mat6riaux composite...the pilot’s orders to the engine and the rotors. --Rear rotor Conventional or "faired propeller" type with its overall pitch control --Vibration

Organic speciation of size-segregated atmospheric particulate matter

NASA Astrophysics Data System (ADS)

Tremblay, Raphael

Particle size and composition are key factors controlling the impacts of particulate matter (PM) on human health and the environment. A comprehensive method to characterize size-segregated PM organic content was developed, and evaluated during two field campaigns. Size-segregated particles were collected using a cascade impactor (Micro-Orifice Uniform Deposit Impactor) and a PM2.5 large volume sampler. A series of alkanes and polycyclic aromatic hydrocarbons (PAHs) were solvent extracted and quantified using a gas chromatograph coupled with a mass spectrometer (GC/MS). Large volume injections were performed using a programmable temperature vaporization (PTV) inlet to lower detection limits. The developed analysis method was evaluated during the 2001 and 2002 Intercomparison Exercise Program on Organic Contaminants in PM2.5 Air Particulate Matter led by the US National Institute of Standards and Technology (NIST). Ambient samples were collected in May 2002 as part of the Tampa Bay Regional Atmospheric Chemistry Experiment (BRACE) in Florida, USA and in July and August 2004 as part of the New England Air Quality Study - Intercontinental Transport and Chemical Transformation (NEAQS - ITCT) in New Hampshire, USA. Morphology of the collected particles was studied using scanning electron microscopy (SEM). Smaller particles (one micrometer or less) appeared to consist of solid cores surrounded by a liquid layer which is consistent with combustion particles and also possibly with particles formed and/or coated by secondary material like sulfate, nitrate and secondary organic aerosols. Source apportionment studies demonstrated the importance of stationary sources on the organic particulate matter observed at these two rural sites. Coal burning and biomass burning were found to be responsible for a large part of the observed PAHs during the field campaigns. Most of the measured PAHs were concentrated in particles smaller than one micrometer and linked to combustion sources

DETECTION AND MOLECULAR ANALYSIS OF PARTICULATE AIR POLLUTION INDUCED CARDIOPULMONARY OXIDATIVE STRESS USING A TRANSGENIC MOUSE MODEL AND EMERGING TECHNOLOGIES

EPA Science Inventory

Identification of particle characteristics and biological mechanism(s) responsible for the adverse pulmonary and cardiovascular responses associated with particulate air pollution exposure remains a critical research activity. We have employed an oxidative stress sensitive an...

40 CFR 52.1880 - Control strategy: Particulate matter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 4 2011-07-01 2011-07-01 false Control strategy: Particulate matter... strategy: Particulate matter. (a) The requirements of subpart G of this chapter are not met because the... matter in the Greater Metropolitan Cleveland Intrastate Region and the Ohio portions of the Northwest...

40 CFR 52.1880 - Control strategy: Particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control strategy: Particulate matter... strategy: Particulate matter. (a) The requirements of subpart G of this chapter are not met because the... matter in the Greater Metropolitan Cleveland Intrastate Region and the Ohio portions of the Northwest...

40 CFR 52.1880 - Control strategy: Particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 4 2013-07-01 2013-07-01 false Control strategy: Particulate matter... strategy: Particulate matter. (a) The requirements of subpart G of this chapter are not met because the... matter in the Greater Metropolitan Cleveland Intrastate Region and the Ohio portions of the Northwest...

40 CFR 52.1880 - Control strategy: Particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 4 2012-07-01 2012-07-01 false Control strategy: Particulate matter... strategy: Particulate matter. (a) The requirements of subpart G of this chapter are not met because the... matter in the Greater Metropolitan Cleveland Intrastate Region and the Ohio portions of the Northwest...

The Relocation of Particulate Contamination During Space Flight

NASA Technical Reports Server (NTRS)

Barengoltz, J.; Edgars, D.

1975-01-01

A computer simulation program to model the redistribution of particulate contaminants on a spacecraft after launch is developed. The component models for particulate adhesion, meteoroid impact, and electrostatic forces are described and intermediate results are presented. The results of a sample calculation show that the recontamination process is important.

Association between ambient particulate matter and disorders of vestibular function.

PubMed

Han, Changwoo; Lim, Youn-Hee; Jung, Kweon; Hong, Yun-Chul

2017-05-01

Exposure to environmental chemicals has been suggested to alter the physiologic state of the inner and middle ear. However, it is unknown if particulate matter exposure is associated with acute vestibular dysfunction. To estimate the effects of particulate matter exposure on the number of hospital visits related to three major diseases of vestibular dysfunction, Meniere's disease (MD), benign paroxysmal positional vertigo (BPPV), and vestibular neuronitis (VN). Our study subject is from Korean National Health Insurance Service-National Sample Cohort, which is dynamic cohort consist of 1 million participants representing the Korean population. Among total cohort participants, we used the hospital visit data of 210,000 individuals who resided in Seoul from 2007 to 2010. Time series analysis using the Poisson generalized additive model and case-crossover analysis using conditional logistic regression were used to investigate the association between daily particulate matter levels (PM 2.5 , particulate matter <2.5μg/m 3 ; PM 10 , particulate matter <10μg/m 3 ; PM 10-2.5 , PM 10 - PM 2.5 ) and number of MD, BPPV, and VN hospital visits. Time series analysis showed that an interquartile range (IQR) increase in PM 10 and PM 10-2.5 on lag day 1 was associated with an increased risk of MD hospital visits [relative risk (RR), 95% confidence interval (CI), PM 10 : 1.09 (1.02-1.15); PM 10-2.5 : 1.06 (1.02-1.10)]. In addition, elderly individuals (≥60 years old) showed an increased risk of MD hospital visits after particulate matter exposure when compared to younger individuals. An IQR increase in particulate matter on lag day 1 was associated with a marginally significant increase in VN hospital visits [RR (95%CI), PM 2.5 : 1.11 (0.98-1.25); PM 10 : 1.07 (0.99-1.15); PM 10-2.5 : 1.04 (0.99-1.09)]. However, no association between particulate matter exposure and BPPV hospital visits was noted. Case-crossover analyses showed similar results to the time-series analysis across

Comparison of the ActiDes-Blue and CARELA HYDRO-DES technology for the sanitation of contaminated cooling water systems in dental units.

PubMed

Kramer, Axel; Lemanski, Sandra; Demond, Kathleen; Assadian, Ojan

2012-01-01

control phase and the action phase could be demonstrated. During the control phase, contamination of the water samples with a mold was noticed so that examinations for molds were carried out beyond the scope of the drinking water directive. For this parameter as well, no significant differences between the phases of the study could be shown.The Legionella load of the dental units was low. L. pneumophila were yielded in only 4 out of 130 water samples. During the control phase, twice colony counts at 50 cfu/1,000 ml and 110 cfu/1,000 ml were measured. During the action phase, counts with Legionella spp. could be measured at 5 cfu/1,000 ml for one unit only. Also, with 1-10 cfu/100 ml, the P. aeruginosa contamination was low. During the application phase, it ranged between 0-7 cfu/100 ml.Redox potential and pH value showed a slight decrease during the application phase.Before treatment with CARELA Solvent and CARELA HYDRO-DES, the initial contamination of the total count of bacterial colonies was 1,432 cfu/ml at 22°C and 846 cfu/ml at 36°C as well as >1,000 cfu/100 ml for molds. 1 h after the decontamination, no bacteria and molds could be detected in 1,000 ml of tap water. Despite the fact that the unit was not used any longer, after 7 d the bacterial colony count was 3 cfu/ml at 22°C and 2 cfu/ml at 36°C while molds could not be detected. Even after a rest time of 14 d only 167 cfu/ml or 42 cfu/ml could be yielded. Molds were further not cultivable. A material damage could not be observed. Pertaining to the ActiDes technology's effectiveness, it has to be pointed out that the dental units investigated were those used for dental students' teaching and therefore were clearly less frequently used than clinically used units in a dental practice. This resulted in distinctly longer stagnation periods which favored formation of biofilms. In summary, the ActiDes technology and ActiDes-Blue showed not to be sufficiently effective for the sanitation of contaminated water

Impact of rail pressure and biodiesel fueling on the particulate morphology and soot nanostructures from a common-rail turbocharged direct injection diesel engine

DOE PAGES

Ye, Peng; Vander Wal, Randy; Boehman, Andre L.; ...

2014-12-26

The effect of rail pressure and biodiesel fueling on the morphology of exhaust particulate agglomerates and the nanostructure of primary particles (soot) was investigated with a common-rail turbocharged direct injection diesel engine. The engine was operated at steady state on a dynamometer running at moderate speed with both low (30%) and medium–high (60%) fixed loads, and exhaust particulate was sampled for analysis. Ultra-low sulfur diesel and its 20% v/v blends with soybean methyl ester biodiesel were used. Fuel injection occurred in a single event around top dead center at three different injection pressures. Exhaust particulate samples were characterized with TEMmore » imaging, scanning mobility particle sizing, thermogravimetric analysis, Raman spectroscopy, and XRD analysis. Particulate morphology and oxidative reactivity were found to vary significantly with rail pressure and with biodiesel blend level. Higher biodiesel content led to increases in the primary particle size and oxidative reactivity but did not affect nanoscale disorder in the as-received samples. For particulates generated with higher injection pressures, the initial oxidative reactivity increased, but there was no detectable correlation with primary particle size or nanoscale disorder.« less

Impact of rail pressure and biodiesel fueling on the particulate morphology and soot nanostructures from a common-rail turbocharged direct injection diesel engine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ye, Peng; Vander Wal, Randy; Boehman, Andre L.

The effect of rail pressure and biodiesel fueling on the morphology of exhaust particulate agglomerates and the nanostructure of primary particles (soot) was investigated with a common-rail turbocharged direct injection diesel engine. The engine was operated at steady state on a dynamometer running at moderate speed with both low (30%) and medium–high (60%) fixed loads, and exhaust particulate was sampled for analysis. Ultra-low sulfur diesel and its 20% v/v blends with soybean methyl ester biodiesel were used. Fuel injection occurred in a single event around top dead center at three different injection pressures. Exhaust particulate samples were characterized with TEMmore » imaging, scanning mobility particle sizing, thermogravimetric analysis, Raman spectroscopy, and XRD analysis. Particulate morphology and oxidative reactivity were found to vary significantly with rail pressure and with biodiesel blend level. Higher biodiesel content led to increases in the primary particle size and oxidative reactivity but did not affect nanoscale disorder in the as-received samples. For particulates generated with higher injection pressures, the initial oxidative reactivity increased, but there was no detectable correlation with primary particle size or nanoscale disorder.« less

40 CFR 60.472 - Standards for particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Asphalt Processing and Asphalt Roofing Manufacture § 60.472 Standards for particulate matter. (a) On and after the...) Particulate matter in excess of: (i) 0.04 kg/Mg (0.08 lb/ton) of asphalt shingle or mineral-surfaced roll...

Etude spectroscopique des collisions moleculaires (hydrogene-azote et hydrogene-oxygene) a des energies de quelques MeV

NASA Astrophysics Data System (ADS)

Plante, Jacinthe

1998-09-01

Les resultats presentes ici proviennent d'une etude systematique portant sur les collisions a vitesse constante, entre les projectiles d'hydrogene (H+, H2+ et H3+ a 1 MeV/nucleon) et deux cibles gazeuses (N2 et O2), soumises a differentes pressions. Les collisions sont analysees a l'aide des spectres d'emission (de 400 A a 6650 A) et des graphiques intensite/pression. Les spectres ont revele la presence des raies d'azote atomique, d'azote moleculaire, d'oxygene atomique, d'oxygene moleculaire et d'hydrogene atomique. Les raies d'hydrogene sont observees seulement avec les projectiles H2+ et H3+. Donc les processus responsables de la formation de ces raies sont des mecanismes de fragmentation des projectiles. Pour conclure, il existe une difference notable entre les projectiles et les differentes pressions. Les raies d'azote et d'oxygene augmentent selon la pression et les raies d'hydrogene atomique presentent une relation non lineaire avec la pression.

40 CFR 49.126 - Rule for limiting fugitive particulate matter emissions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Rule for limiting fugitive particulate matter emissions. (a) What is the purpose of this section? This section limits the amount of fugitive particulate matter that may be emitted from certain air pollution... source of fugitive particulate matter emissions. (c) What is exempted from this section? This section...

Methode d'identification parametrique pour la surveillance in situ des joints a recouvrement par propagation d'ondes vibratoires

NASA Astrophysics Data System (ADS)

Francoeur, Dany

Cette these de doctorat s'inscrit dans le cadre de projets CRIAQ (Consortium de recherche et d'innovation en aerospatiale du Quebec) orientes vers le developpement d'approches embarquees pour la detection de defauts dans des structures aeronautiques. L'originalite de cette these repose sur le developpement et la validation d'une nouvelle methode de detection, quantification et localisation d'une entaille dans une structure de joint a recouvrement par la propagation d'ondes vibratoires. La premiere partie expose l'etat des connaissances sur l'identification d'un defaut dans le contexte du Structural Health Monitoring (SHM), ainsi que la modelisation de joint a recouvrements. Le chapitre 3 developpe le modele de propagation d'onde d'un joint a recouvrement endommage par une entaille pour une onde de flexion dans la plage des moyennes frequences (10-50 kHz). A cette fin, un modele de transmission de ligne (TLM) est realise pour representer un joint unidimensionnel (1D). Ce modele 1D est ensuite adapte a un joint bi-dimensionnel (2D) en faisant l'hypothese d'un front d'onde plan incident et perpendiculaire au joint. Une methode d'identification parametrique est ensuite developpee pour permettre a la fois la calibration du modele du joint a recouvrement sain, la detection puis la caracterisation de l'entaille situee sur le joint. Cette methode est couplee a un algorithme qui permet une recherche exhaustive de tout l'espace parametrique. Cette technique permet d'extraire une zone d'incertitude reliee aux parametres du modele optimal. Une etude de sensibilite est egalement realisee sur l'identification. Plusieurs resultats de mesure sur des joints a recouvrements 1D et 2D sont realisees permettant ainsi l'etude de la repetabilite des resultats et la variabilite de differents cas d'endommagement. Les resultats de cette etude demontrent d'abord que la methode de detection proposee est tres efficace et permet de suivre la progression d'endommagement. De tres bons resultats

Smoke detection in low-G fires

NASA Technical Reports Server (NTRS)

Urban, David L.; Griffin, Devon W.; Gard, Melissa Y.; Hoy, Michael

1995-01-01

Fires in spacecraft are considered a credible risk. To respond to this risk, NASA flew fire detectors on Skylab and the Space Shuttle (STS) and included them in the design for International Space Station Alpha (ISSA). In previous missions (Mercury, Gemini and Apollo), the crew quarters were so cramped that it was not considered credible that the astronauts could fail to observe a fire. The Skylab nodule included approximately 20 UV fire detectors. The space shuttle has 9 ionization detectors in the mid deck and flight deck and Spacelab has six additional ionization detectors. The planned detectors for ISSA are laser-diode, forward-scattering, smoke or particulate detectors. Current plans for the ISSA call for two detectors in the open area of the module and detectors in racks that have both cooling air flow and electrical power. Due to the complete absence of data concerning the nature of particulate and radiant emission from low-g fires, all three of these detector systems were designed based upon 1-g test data. As planned mission durations and complexity increase and the volume of spacecraft increases, the need for and importance of effective, crew independent, fire detection grows significantly. This requires more knowledge concerning low-gravity fires and how they might be detected. To date, no combustion-generated particulate samples have been collected for well-developed microgravity flames. All of the extant data come from drop tower tests and therefore only correspond to the early stages of a fire. The fuel sources were restricted to laminar gas-jet diffusion flames and rapidly overheated wire insulation. These gas-jet drop tower tests indicate, through thermophoretic sampling, that soot primaries and aggregates (groups of primary particles) in micro-g may be significantly larger than those in normal-g (ng). This raises new scientific questions about soot processes as well as practical issues for particulate detection/alarm threshold levels used in on

DES Science Portal: II- Creating Science-Ready Catalogs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fausti Neto, Angelo; et al.

We present a novel approach for creating science-ready catalogs through a software infrastructure developed for the Dark Energy Survey (DES). We integrate the data products released by the DES Data Management and additional products created by the DES collaboration in an environment known as DES Science Portal. Each step involved in the creation of a science-ready catalog is recorded in a relational database and can be recovered at any time. We describe how the DES Science Portal automates the creation and characterization of lightweight catalogs for DES Year 1 Annual Release, and show its flexibility in creating multiple catalogs withmore » different inputs and configurations. Finally, we discuss the advantages of this infrastructure for large surveys such as DES and the Large Synoptic Survey Telescope. The capability of creating science-ready catalogs efficiently and with full control of the inputs and configurations used is an important asset for supporting science analysis using data from large astronomical surveys.« less

Chemical characterization of freshly emitted particulate matter from aircraft exhaust using single particle mass spectrometry

NASA Astrophysics Data System (ADS)

Abegglen, Manuel; Brem, B. T.; Ellenrieder, M.; Durdina, L.; Rindlisbacher, T.; Wang, J.; Lohmann, U.; Sierau, B.

2016-06-01

Non-volatile aircraft engine emissions are an important anthropogenic source of soot particles in the upper troposphere and in the vicinity of airports. They influence climate and contribute to global warming. In addition, they impact air quality and thus human health and the environment. The chemical composition of non-volatile particulate matter emission from aircraft engines was investigated using single particle time-of-flight mass spectrometry. The exhaust from three different aircraft engines was sampled and analyzed. The soot particulate matter was sampled directly behind the turbine in a test cell at Zurich Airport. Single particle analyses will focus on metallic compounds. The particles analyzed herein represent a subset of the emissions composed of the largest particles with a mobility diameter >100 nm due to instrumental restrictions. A vast majority of the analyzed particles was shown to contain elemental carbon, and depending on the engine and the applied thrust the elemental carbon to total carbon ratio ranged from 83% to 99%. The detected metallic compounds were all internally mixed with the soot particles. The most abundant metals in the exhaust were Cr, Fe, Mo, Na, Ca and Al; V, Ba, Co, Cu, Ni, Pb, Mg, Mn, Si, Ti and Zr were also detected. We further investigated potential sources of the ATOFMS-detected metallic compounds using Inductively Coupled Plasma Mass Spectrometry. The potential sources considered were kerosene, engine lubrication oil and abrasion from engine wearing components. An unambiguous source apportionment was not possible because most metallic compounds were detected in several of the analyzed sources.

VR-CoDES and patient-centeredness. The intersection points between a measure and a concept.

PubMed

Del Piccolo, Lidia

2017-11-01

The Verona Coding Definitions of Emotional sequences (VR-CoDES) system has been applied in a wide range of studies, in some of these, because of its attention on healthcare provider's ability to respond to patient emotions, it has been used as a proxy of patient-centeredness. The paper aims to discuss how the VR-CoDES can contribute to the broader concept of patient-centeredness and its limitations. VR-CoDES and patient-centeredness concept are briefly described, trying to detect commonalities and distinctions. The VR-CoDES dimensions of Explicit/non explicit responding and Providing or Reducing Space are analysed in relation to relevant aspects of patient-centred communication. Emotional aspects are encompassed within patient-centeredness model, but they represent only one of the numerous dimensions that contribute to define patient-centeredness as well as Explicit/non explicit responding and Providing or Reducing Space serve different functions during communication. The VR-CoDES can contribute to operationalize the description of emotional aspects emerging in a consultation, by inducing coders to adopt a factual attitude in assessing how health providers react to patient's expression of emotions. To better define empirically which measure affective aspects and dimensions of health provider responses are relevant and may contribute to patient-centeredness in different clinical settings. Copyright © 2017. Published by Elsevier B.V.

Airborne soil particulates as vehicles for Salmonella contamination of tomatoes.

PubMed

Kumar, Govindaraj Dev; Williams, Robert C; Al Qublan, Hamzeh M; Sriranganathan, Nammalwar; Boyer, Renee R; Eifert, Joseph D

2017-02-21

The presence of dust is ubiquitous in the produce growing environment and its deposition on edible crops could occur. The potential of wind-distributed soil particulate to serve as a vehicle for S. Newport transfer to tomato blossoms and consequently, to fruits, was explored. Blossoms were challenged with previously autoclaved soil containing S. Newport (9.39log CFU/g) by brushing and airborne transfer. One hundred percent of blossoms brushed with S. Newport-contaminated soil tested positive for presence of the pathogen one week after contact (P<0.0001). Compressed air was used to simulate wind currents and direct soil particulates towards blossoms. Airborne soil particulates resulted in contamination of 29% of the blossoms with S. Newport one week after contact. Biophotonic imaging of blossoms post-contact with bioluminescent S. Newport-contaminated airborne soil particulates revealed transfer of the pathogen on petal, stamen and pedicel structures. Both fruits and calyxes that developed from blossoms contaminated with airborne soil particulates were positive for presence of S. Newport in both fruit (66.6%) and calyx (77.7%). Presence of S. Newport in surface-sterilized fruit and calyx tissue tested indicated internalization of the pathogen. These results show that airborne soil particulates could serve as a vehicle for Salmonella. Hence, Salmonella contaminated dust and soil particulate dispersion could contribute to pathogen contamination of fruit, indicating an omnipresent yet relatively unexplored contamination route. Copyright © 2016 Elsevier B.V. All rights reserved.

Integrated digital error suppression for improved detection of circulating tumor DNA

PubMed Central

Kurtz, David M.; Chabon, Jacob J.; Scherer, Florian; Stehr, Henning; Liu, Chih Long; Bratman, Scott V.; Say, Carmen; Zhou, Li; Carter, Justin N.; West, Robert B.; Sledge, George W.; Shrager, Joseph B.; Loo, Billy W.; Neal, Joel W.; Wakelee, Heather A.; Diehn, Maximilian; Alizadeh, Ash A.

2016-01-01

High-throughput sequencing of circulating tumor DNA (ctDNA) promises to facilitate personalized cancer therapy. However, low quantities of cell-free DNA (cfDNA) in the blood and sequencing artifacts currently limit analytical sensitivity. To overcome these limitations, we introduce an approach for integrated digital error suppression (iDES). Our method combines in silico elimination of highly stereotypical background artifacts with a molecular barcoding strategy for the efficient recovery of cfDNA molecules. Individually, these two methods each improve the sensitivity of cancer personalized profiling by deep sequencing (CAPP-Seq) by ~3 fold, and synergize when combined to yield ~15-fold improvements. As a result, iDES-enhanced CAPP-Seq facilitates noninvasive variant detection across hundreds of kilobases. Applied to clinical non-small cell lung cancer (NSCLC) samples, our method enabled biopsy-free profiling of EGFR kinase domain mutations with 92% sensitivity and 96% specificity and detection of ctDNA down to 4 in 105 cfDNA molecules. We anticipate that iDES will aid the noninvasive genotyping and detection of ctDNA in research and clinical settings. PMID:27018799

PIXE analysis of airborne particulate matter from Monterrey, Mexico. A first survey

NASA Astrophysics Data System (ADS)

Aldape, F.; Flores M, J.; Díaz, R. V.; Hernández-Méndez, B.; Montoya Z, J. M.; Blanco, E. E.; Fuentes, A. F.; Torres-Martínez, L. M.

1999-04-01

A first survey of elemental contents in airborne particulate matter from Monterrey, Nuevo León, Mexico, was performed using PIXE. This second largest industrial city is located 715 km north of Mexico City, and counts with a population of nearly three million inhabitants in its conurbation. Air pollution in the place comes from a great variety of industries ranging from iron smelters to furniture manufacturing, as well as from fuel combustion in vehicles and industries. This study presents results of elemental contents in airborne particulate matter in two particle size fractions: PM 2.5 and PM 15. The samples were collected during five weeks on working days, Monday-Friday, from 9 December 1996 to 14 January 1997. Two samples a day were collected, 12 h each, night-time and day-time. These first results show local pollution as typical from a large urban area in conjunction with an active industry. Thirteen elements were consistently detected in most of the samples and some episodes due to both industrial and human activities were identified. A general discussion about the results obtained is presented.

Exposure assessment of particulates of diesel and natural gas fuelled buses in silico.

PubMed

Pietikäinen, Mari; Oravisjärvi, Kati; Rautio, Arja; Voutilainen, Arto; Ruuskanen, Juhani; Keiski, Riitta L

2009-12-15

Lung deposition estimates of particulate emissions of diesel and natural gas (CNG) fuelled vehicles were studied by using in silico methodology. Particulate emissions and particulate number size distributions of two Euro 2 petroleum based diesel buses and one Euro 3 gas bus were measured. One of the petroleum based diesel buses used in the study was equipped with an oxidation catalyst on the vehicle (DI-OC) while the second had a partial-DPF catalyst (DI-pDPF). The third bus used was the gas bus with an oxidation catalyst on the vehicle (CNG-OC). The measurements were done using a transient chassis dynamometer test cycle (Braunschweig cycle) and an Electric Low Pressure Impactor (ELPI) with formed particulates in the size range of 7 nm to 10 microm. The total amounts of the emitted diesel particulates were 88-fold for DI-OC and 57-fold for DI-pDPF compared to the total amount of emitted CNG particulates. Estimates for the deposited particulates were computed with a lung deposition model ICRP 66 using in-house MATLAB scripts. The results were given as particulate numbers and percentages deposited in five different regions of the respiratory system. The percentages of particulates deposited in the respiratory system were 56% for DI-OC, 51% for DI-pDPF and 77% for CNG-OC of all the inhaled particulates. The result shows that under similar conditions the total lung dose of particulates originating from petroleum diesel fuelled engines DI-OC and DI-pDPF was more than 60-fold and 35-fold, respectively, compared to the lung dose of particulates originating from the CNG fuelled engine. The results also indicate that a majority (35-50%) of the inhaled particulates emitted from the tested petroleum diesel and CNG engines penetrate deep into the unciliated regions of the lung where gas-exchange occurs.

Reticulation des fibres lignocellulosiques

NASA Astrophysics Data System (ADS)

Landrevy, Christel

Pour faire face à la crise économique la conception de papier à valeur ajoutée est développée par les industries papetières. Le but de se projet est l'amélioration des techniques actuelles de réticulation des fibres lignocellulosiques de la pâte à papier visant à produire un papier plus résistant. En effet, lors des réactions de réticulation traditionnelles, de nombreuses liaisons intra-fibres se forment ce qui affecte négativement l'amélioration anticipée des propriétés physiques du papier ou du matériau produit. Pour éviter la formation de ces liaisons intra-fibres, un greffage sur les fibres de groupements ne pouvant pas réagir entre eux est nécessaire. La réticulation des fibres par une réaction de « click chemistry » appelée cycloaddition de Huisgen entre un azide et un alcyne vrai, catalysée par du cuivre (CuAAC) a été l'une des solutions trouvée pour remédier à ce problème. De plus, une adaptation de cette réaction en milieux aqueux pourrait favoriser son utilisation en milieu industriel. L'étude que nous désirons entreprendre lors de ce projet vise à optimiser la réaction de CuAAC et les réactions intermédiaires (propargylation, tosylation et azidation) sur la pâte kraft, en milieu aqueux. Pour cela, les réactions ont été adaptées en milieu aqueux sur la cellulose microcristalline afin de vérifier sa faisabilité, puis transférée à la pâte kraft et l'influence de différents paramètres comme le temps de réaction ou la quantité de réactifs utilisée a été étudiée. Dans un second temps, une étude des différentes propriétés conférées au papier par les réactions a été réalisée à partir d'une série de tests papetiers optiques et physiques. Mots Clés Click chemistry, Huisgen, CuAAC, propargylation, tosylation, azidation, cellulose, pâte kraft, milieu aqueux, papier.

Electrification of particulate entrained fluid flows-Mechanisms, applications, and numerical methodology

NASA Astrophysics Data System (ADS)

Wei, Wei; Gu, Zhaolin

2015-10-01

Particulates in natural and industrial flows have two basic forms: liquid (droplet) and solid (particle). Droplets would be charged in the presence of the applied electric field (e.g. electrospray). Similar to the droplet charging, particles can also be charged under the external electric field (e.g. electrostatic precipitator), while in the absence of external electric field, tribo-electrostatic charging is almost unavoidable in gas-solid two-phase flows due to the consecutive particle contacts (e.g. electrostatic in fluidized bed or wind-blown sand). The particle charging may be beneficial, or detrimental. Although electrostatics in particulate entrained fluid flow systems have been so widely used and concerned, the mechanisms of particulate charging are still lack of a thorough understanding. The motivation of this review is to explore a clear understanding of particulate charging and movement of charged particulate in two-phase flows, by summarizing the electrification mechanisms, physical models of particulate charging, and methods of charging/charged particulate entrained fluid flow simulations. Two effective methods can make droplets charged in industrial applications: corona charging and induction charging. The droplet charge to mass ratio by corona charging is more than induction discharge. The particle charging through collisions could be attributed to electron transfer, ion transfer, material transfer, and/or aqueous ion shift on particle surfaces. The charges on charged particulate surface can be measured, nevertheless, the charging process in nature or industry is difficult to monitor. The simulation method might build a bridge of investigating from the charging process to finally charged state on particulate surface in particulate entrained fluid flows. The methodology combining the interface tracking under the action of the applied electric with the fluid flow governing equations is applicable to the study of electrohydrodynamics problems. The charge

Effect of pollution by particulate iron on the morphoanatomy, histochemistry, and bioaccumulation of three mangrove plant species in Brazil.

PubMed

Arrivabene, Hiulana Pereira; Souza, Iara da Costa; Có, Walter Luiz Oliveira; Conti, Melina Moreira; Wunderlin, Daniel Alberto; Milanez, Camilla Rozindo Dias

2015-05-01

In Brazil, some mangrove areas are subjected to air pollution by particulate iron from mining activities. However, the effect of this pollutant on mangrove plants is not well known. This study aimed to comparatively analyze the morphoanatomy, histochemistry, and iron accumulation in leaves of Avicennia schaueriana, Laguncularia racemosa, and Rhizophora mangle. Samples were collected from five mangrove sites of Espírito Santo state, each of which is exposed to different levels of particulate iron pollution. The amount of particulate material settled on the leaf surface was greater in A. schaueriana and L. racemosa, which contain salt glands. High iron concentrations were found in leaves of this species, collected from mangrove areas with high particulate iron pollution, which suggests the foliar absorption of this element. None of the samples from any of the sites showed morphological or structural damage on the leaves. Scanning electron microscopy (SEM) coupled to X-ray diffraction rendered a good method for evaluating iron on leaves surfaces. A histochemical test using Prussian blue showed to be an appropriate method to detect iron in plant tissue, however, proved to be an unsuitable method for the assessment of the iron bioaccumulation in leaves of A. schaueriana and R. mangle. So far, this study demonstrates the need of evaluating the pathway used by plants exposed to contaminated particulate matter to uptake atmospheric pollutants. Copyright © 2015 Elsevier Ltd. All rights reserved.

40 CFR 86.145-82 - Calculations; particulate emissions.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., inside the dilution air filter box at EPA is very low. Pb will be assumed = 0, and background particulate.... 86.145-82 Section 86.145-82 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... further defined in § 86.144. (3) P e = mass of particulate per test on the exhaust filter(s), grams. (4...

40 CFR 86.145-82 - Calculations; particulate emissions.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., inside the dilution air filter box at EPA is very low. Pb will be assumed = 0, and background particulate.... 86.145-82 Section 86.145-82 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... further defined in § 86.144. (3) P e = mass of particulate per test on the exhaust filter(s), grams. (4...

Spatial Statistics of atmospheric particulate matter in China

NASA Astrophysics Data System (ADS)

Huang, Yongxiang; Wang, Yangjun; Liu, Yulu

2017-04-01

In this work, the spatial dynamics of the atmospheric particulate matters (resp. PM10 and PM2.5) are studied using turbulence methodologies. The hourly concentrations of particulate matter were released by the Chinese government (http://www.cnemc.cn). We first processed these data into daily average concentrations. Totally, there are 305 monitor stations with an observations period of 425 days. It is found experimentally that the spatial correlation function ρ(r) shows a log-law on the mesoscale range, i.e., 50 ≤ r ≤ 500 km, with an experimental scaling exponent β = 0.45. The spatial structure function shows a power-law behavior on the mesoscale range 90 ≤ r ≤ 500 km. The experimental scaling exponent ζ(q) is convex, showing that the intermittent correction is relevant in characterizing the spatial dynamics of particulate matter. The measured singularity spectrum f(α) also shows its multifractal nature. Experimentally, the particulate matter is more intermittent than the passive scalar, which could be partially due to the mesoscale movements of the atmosphere, and also due to local sources, such as local industry activities.

Minimisation des inductances propres des condensateurs à film métallisé

NASA Astrophysics Data System (ADS)

Joubert, Ch.; Rojat, G.; Béroual, A.

1995-07-01

In this article, we examine the different factors responsible for the equivalent series inductance in metallized capacitors and we propose structures for capacitors that reduce this inductance. After recalling the structure of metallized capacitors we compare, by experimental measurements, the inductance due to the winding and that one added by the connections. The latter can become preponderant. In order to explain the experimental evolution of the winding impedance vs. frequency, we describe an analytical model which gives the current density in the winding and its impedance. This model enables us to determine the self resonant frequency for different types of capacitors. From where, we can infer the influence of the height of capacitors and their internal and external radius upon performances, It appears that to reduce the equivalent series inductance, it is better to use flat windings and annular windings. Dans cet article nous examinons les différents facteurs responsables de l'inductance équivalente série dans les condensateurs à film métallisé et proposons des géométries de condensateurs qui réduisent cette inductance. Après avoir rappelé la structure des condensateurs à film métallisé, nous comparons, par des mesures expérimentales, l'inductance due au bobinage et l'inductance ajoutée par les connexions. Cette dernière peut devenir prépondérante. Afin d'expliquer l'évolution de l'impédance du bobinage en fonction de la fréquence, nous décrivons un modèle analytique qui donne la densité du courant dans le bobinage et l'impédance de ce dernier. En outre, ce modèle permet de déterminer la fréquence de résonance série de divers types de condensateurs ce qui permet de déduire l'influence de la hauteur des condensateurs et de leurs rayons interne et externe sur les performances. Il apparaît ainsi que, pour diminuer l'inductance équivalente série, il vaut mieux employer des bobinages plats et des bobinages annulaires.

Automatic localization of backscattering events due to particulate in urban areas

NASA Astrophysics Data System (ADS)

Gaudio, P.; Gelfusa, M.; Malizia, Andrea; Parracino, Stefano; Richetta, M.; Murari, A.; Vega, J.

2014-10-01

Particulate matter (PM), emitted by vehicles in urban traffic, can greatly affect environment air quality and have direct implications on both human health and infrastructure integrity. The consequences for society are relevant and can impact also on national health. Limits and thresholds of pollutants emitted by vehicles are typically regulated by government agencies. In the last few years, the interest in PM emissions has grown substantially due to both air quality issues and global warming. Lidar-Dial techniques are widely recognized as a costeffective alternative to monitor large regions of the atmosphere. To maximize the effectiveness of the measurements and to guarantee reliable, automatic monitoring of large areas, new data analysis techniques are required. In this paper, an original tool, the Universal Multi-Event Locator (UMEL), is applied to the problem of automatically indentifying the time location of peaks in Lidar measurements for the detection of particulate matter emitted by anthropogenic sources like vehicles. The method developed is based on Support Vector Regression and presents various advantages with respect to more traditional techniques. In particular, UMEL is based on the morphological properties of the signals and therefore the method is insensitive to the details of the noise present in the detection system. The approach is also fully general, purely software and can therefore be applied to a large variety of problems without any additional cost. The potential of the proposed technique is exemplified with the help of data acquired during an experimental campaign in the field in Rome.

Investigation experimentale de l'ecoulement et des performances thermiques du nanofluide eau-oxyde de cuivre dans un Micro-Canal Chauffe

NASA Astrophysics Data System (ADS)

Rimbault, Benjamin

Cette these de maitrise presentee par articles visait a etudier le comportement hydraulique et thermique d'un ecoulement de nanofluides en micro-canal chauffe. Nous avons etudie premierement de l'eau distillee, ensuite des melanges de particules d'oxyde de cuivre (taille 29nm) avec de l'eau distillee en concentrations particulaires volumiques 4.5%, 1.03%, et 0.24% (CuO-H2O). L'ecoulement force des differents fluides a ete realise au moyen de pompes a engrenages au sein d'un circuit ferme, comprenant un micro-canal a section rectangulaire (e=1.116mm,1=25.229mm) chauffe sur deux faces paralleles via des cartouches electriques, deux echangeurs de chaleurs en serie, ainsi qu'un debitmetre magnetique. A notre connaissance peu d'etudes sur l'ecoulement de nanofluides d'oxyde de cuivre-eau en micro-canal rectangulaire chauffe sont disponibles dans la litterature, cette recherche sert de contribution. Premierement, une validation avec la litterature a ete effectuee pour le cas d'un ecoulement d'eau entre plaques planes paralleles chauffees. Des essais hydrauliques ont ete realises pour une gamme du nombre de Reynolds allant jusqu'a Re=5000 a temperature constante. Par la suite des essais thermiques jusqu'a Re=2500 ont consiste en une elevation de temperature fixe (20.5°C a 30.5°C) a travers la longueur du micro-canal sous un regime stationnaire. Les resultats ont demontre une augmentation de la perte de pression et du coefficient de frottement des nanofluides sur l'eau pour un meme debit. Une telle augmentation de perte de pression etait de +70%, +25%, et +0 a 30% respectivement pour les concentrations 4.50%, 1.03%, et 0.24%. Concernant la transition laminaire a turbulent les comportements semblaient indiquer une valeur critique semblable entre l'eau et les differentes concentrations avec et sans chauffage a un nombre de Reynolds critique Rem 1000. Nous avons observe une legere augmentation du coefficient de convection thermique avec le debit massique pour les faibles

Particulate carbon and nitrogen and suspended particulate matter in the Sacramento River at Rio Vista, California, January 3 - May 26, 1983 and October 31, 1983 - November 29, 1984

USGS Publications Warehouse

Hager, Stephen W.

1994-01-01

Particulate matter was collected at Rio Vista, California, in two study periods; the first, from January 3 to May 26, 1983; the second from October 31, 1983 to November 29, 1984. Concentrations of suspended particulate matter were measured gravimetrically on silver membrane filters. The pooled standard deviation on replicated samples was 1.4 mg/L, giving a coefficient of variation of 5.7 percent. Concentrations of particulate carbon and nitrogen were measured during a Perkin-Elmer model 240C elemental analyzer to combust material collected on glass fiber filters. Refrigeration of samples prior to filtration was shown to be a likely influence on precision of duplicate analyses. Median deviations between duplicates for carbon were 5.4 percent during the first study period and 8.9 percent during the second. For nitrogen, median deviations were 4.9 percent and 7.2 percent, respectively. This report presents the data for concentrations of suspended particulate material, the duplicate analyses for particulate carbon and nitrogen, and the volumes of sample filtered for the particulate carbon and nitrogen analyses for both studies. Not all samples collected during the second study have been analyzed for particulate carbon and nitrogen.

Apport des neutrons à l'analyse structurale des composés partiellement désordonnés

NASA Astrophysics Data System (ADS)

Cousson, A.

2003-02-01

La cristallographie est un outil extrêmement puissant qui pourrait être utilisé par de nombreux scientifiques dont les sujets de recherche sont en fait très éloignés. L'évolution des techniques ces dernières années a relégué par exemple la cristallographie des rayons X des petites molécules à un rôle mineur, un rôle de service. Certains ont même le sentiment semble-t-il que toutes les connaissances sont contenues dans de multiples logiciels capables par eux-mêmes de conduire une analyse structurale à un résultat correct unique. Il est souhaitable que chacun soit capable de réaliser l'étude structurale du composé qui l'intéresse et bien entendu nécessaire de comprendre ce que l'on fait, la qualité des résultats et leur analyse en dépend. L'objet de cette présentation est de montrer l'apport spécifique de la diffraction de neutrons sur monocristaux à l'étude du désordre, en particulier des atomes d'hydrogène, et ses conséquences sur la compréhension des propriétés physiques, à partir de développements et d'exemples récents.

Electrically heated particulate filter regeneration methods and systems for hybrid vehicles

DOEpatents

Gonze, Eugene V.; Paratore, Jr., Michael J.

2010-10-12

A control system for controlling regeneration of a particulate filter for a hybrid vehicle is provided. The system generally includes a regeneration module that controls current to the particulate filter to initiate regeneration. An engine control module controls operation of an engine of the hybrid vehicle based on the control of the current to the particulate filter.

PARTICULATE EMISSIONS AND CONTROL IN FLUIDIZED-BED COMBUSTION: MODELING AND PARAMETRIC PERFORMANCE

EPA Science Inventory

The report discusses a model, developed to describe the physical characteristics of the particulates emitted from fluidized-bed combustion (FBC) systems and to evaluate data on FBC particulate control systems. The model, which describes the particulate emissions profile from FBC,...

Holographic investigation of solid propellant particulates

NASA Astrophysics Data System (ADS)

Gillespie, T. R.

1981-12-01

The investigation completed the development process to establish a technique to obtain holographic recordings of particulate behavior during the combustion process of solid propellants in a two-dimensional rocket motor. Holographic and photographic recordings were taken in a crossflow environment using various compositions of metallized propellants. The reconstructed holograms are used to provide data on the behavior of aluminum/aluminum oxide particulates in a steady state combustion environment as a function of the initial aluminum size cast into the propellant. High speed, high resolution motion pictures were taken to compare the cinematic data with that available from the holograms.

La physique des bulles de champagne Une première approche des processus physico-chimiques liés à l'effervescence des vins de Champagne

NASA Astrophysics Data System (ADS)

Liger-Belair, G.

2002-07-01

ésumons ci-après les principaux résultats obtenus pour chacune des étapes de la vie de la bulle, depuis sa naissance sur les parois d'une flûte, jusqu'à son éclatement en surface. Naissance de la bulle À l'aide d'une caméra munie d'un objectif de microscope, nous avons pu mettre en évidence les particules qui jouent le rôle de sites de nucléation des bulles sur les parois d'une flûte à champagne. Dans la très grande majorité des cas, ce sont des fibres creuses et allongées, de quelques dizaines à quelques centaines de microns, qui assurent la production répétitive de bulles par nucléation hétérogène non classique (de type IV). Cette production répétitive de bulles au niveau des sites de nucléation est caractérisée par une gamme de fréquences de bullage assez large. Au sein d'une même flûte, immédiatement après le versement, nous avons mesuré des fréquences qui varient de moins de 1 Hz à presque 30 Hz. C'est donc jusqu'à 30 bulles qui sont émises chaque seconde par les sites de nucléation les plus actifs. Vitesse ascensionnelle d'une bulle Pour mesurer la vitesse d'une bulle tout au long de son trajet vers la surface libre du champagne, nous avons tiré profit de la production répétitive de bulles au niveau des sites de nucléation. Par la mise en place d'un dispositif expérimental simple qui associe une lumière stroboscopique et un appareil photographique muni de bagues macros, nous avons pu accéder à l'observation fine des trains de bulles ainsi qu'à la détermination de la vitesse ascensionnelle des bulles. Les mesures expérimentales du rayon et de la vitesse d'une bulle nous ont permis de déterminer le coefficient de traînée d'une bulle montante qui constitue une mesure indirecte de son état de surface en terme de mobilité interfaciale. Ces mesures nous ont montré que l'interface d'une bulle de champagne conserve une grande mobilité pendant sa phase ascensionnelle. C'est la faible dilution du champagne en macromol

Apport des moyens endoscopiques dans la dilatation des sténoses caustiques de l’œsophage

PubMed Central

Seydou, Togo; Abdoulaye, Ouattara Moussa; xing, Li; Zi, Sanogo Zimogo; sekou, Koumaré; Wen, Yang Shang; Ibrahim, Sankare; Sekou, Toure Cheik Ahmed; Boubacar, Maiga Ibrahim; Saye, Jacque; Jerome, Dakouo Dodino; Dantoumé, Toure Ousmane; Sadio, Yena

2016-01-01

Introduction Toutes les sténoses symptomatiques de l’œsophage peuvent être dilatées par voie endoscopique. Nous évaluons l'apport des moyens endoscopiques dans la prise en charge de la dilatation œsophagienne pour sténose caustique de l’œsophage (SCO) au Mali. Méthodes IL s'agissait d'une étude descriptive et prospective réalisée dans le service de chirurgie thoracique à l'hôpital du Mali. Au total 46 dossiers cliniques de patients on été enregistrés et subdivisés en 4 groupes en fonction de la topographie des lésions cicatricielles. Le nombre de cas d'assistance endoscopique réalisé a été déterminé afin de comprendre l'apport des moyens endoscopiques dans le succès de la dilatation des SCO. Pour les 2 différentes méthodes de dilatation utilisées, le résultat du traitement et le coût ont comparés. Résultats La FOGD a été utilisée dans 19 cas (41.30%) de dilatation avec la bougie de Savary Guillard et dans 47.82% des cas dans la dilatation de Lerut. La vidéo-laryngoscopie a été utilisé 58.69% des cas de dilatation à la bougie de Lerut. Le passage de guide métallique et / ou de fil-guide a été réalisée dans 39.13% avec la vidéo laryngoscopie et dans 58.68% avec la FOGD. Dans la comparaison des deux méthodes, il existe une différence significative dans la survenue des complications (p=0.04075), l'anesthésie générale (p=0.02287), l'accessibilité à la méthode (p=0.04805) et la mortalité (p=0.00402). Conclusion La SCO est une pathologie grave et sous évaluée au Mali. Les moyens endoscopiques contribuent considérablement au succès de la dilatation œsophagienne pour sténose caustique dans les différentes méthodes utilisées. PMID:27200129

Performance comparison between multienzymes loaded single and dual electrodes for the simultaneous electrochemical detection of adenosine and metabolites in cancerous cells.

PubMed

Hussain, Khalil K; Akhtar, Mahmood H; Kim, Moo-Hyun; Jung, Dong-Keun; Shim, Yoon-Bo

2018-06-30

The analytical performance of the multi enzymes loaded single electrode sensor (SES) and dual electrode sensor (DES) was compared for the detection of adenosine and metabolites. The SES was fabricated by covalent binding of tri-enzymes, adenosine deaminase (ADA), purine nucleoside phosphorylase (PNP), and xanthine oxidase (XO) along with hydrazine (Hyd) onto a functionalized conducting polymer [2,2:5,2-terthiophene-3-(p-benzoic acid)] (pTTBA). The enzyme reaction electrode in DES was fabricated by covalent binding of ADA and PNP onto pTTBA coated on Au nanoparticles. The detection electrode in DES was constructed by covalent binding of XO and Hyd onto pTTBA coated on porous Au. Due to the higher amount (3.5 folds) of the immobilized enzymes and Hyd onto the DES than SES, and the lower Michaelis constant (Km) value for DES (28.7 µM) compared to SES (36.1 µM), the sensitivity was significantly enhanced for the DES (8.2 folds). The dynamic range obtained using DES was from 0.5 nM to 120.0 µM with a detection limit of 1.43 nM ± 0.02, 0.76 nM ± 0.02, and 0.48 nM ± 0.01, for adenosine (AD), inosine (IN), and hypoxanthine (Hypo) respectively. Further, the DES was coupled with an electrochemical potential modulated microchannel for the separation and simultaneous detection of AD, IN, and Hypo in an extracellular matrix of cancerous (A549) and non-cancerous (Vero) cells. The sensor probe confirms a higher basal level of extracellular AD and its metabolites in cancer cells compared to normal cells. In addition, the effect of dipyridamole on released adenosine in A549 cells was investigated. Copyright © 2018 Elsevier B.V. All rights reserved.

Detection of Oil in Water Column, Final Report: Detection Prototype Tests

DTIC Science & Technology

2014-07-01

first phase of the project involved initial development and testing of three technologies to address the detection problem . This second phase...important oceanic phenomena such as density stratification and naturally occurring particulate matter, which will affect the performance of sensors in the ...2 UNCLAS//Public | CG-926 RDC | M. Fitzpatrick, et al.| Public July 2014 spills of submerged oil is far more complex due to the problems

La projection par plasma : une revue

NASA Astrophysics Data System (ADS)

Fauchais, P.; Grimaud, A.; Vardelle, A.; Vardelle, M.

are presented in the fields of aeronautics and mechanics. La qualité d'un dépôt projete par plasma dépend de nombreux paramètres que l'on commence à mieux appréhender du fait des progrès de la modélisation et de la métrologie tant des écoulements plasmas que des transferts plasma-particules ou que des conditions d'écrasement et de refroidissement des particules lors de leur impact sur le substrat ou les couches déjà déposées. Les techniques de mesure utilisdes et leurs limitations sont d'abord rappelées tant pour les jets de plasma que pour les particules en vol et l'importance des différents phénomènes intervenant dans les transferts plasma-particules est soulignée : gradients de température et de concentration d'espèces chimiques très élevés autour des particules, effets de propagation de la chaleur, notamment pour les particules céramiques, effet d'évaporation, effet de raréfaction sensible dès la pression atmosphérique. Les problèmes de distribution de taille et de vitesse d'injection des particules sont également abordés car ils conditionnent les distributions de trajectoires et donc le traitement des particules dans le jet de plasma. La génération du plasma montre d'une part 1'influence considérable de l'injection du gaz, de sa nature, du dessin de la chambre d'arc et de la tuyère ainsi que du pompage de l'air ambiant sur la longueur des jets de plasma d'arc et d'autre part les problèmes d'injection pour éviter le couplage avec la décharge dans les jets de plasmas R.E Tout ceci est illustré avec des exemples de dépôt d'alumine, de zircone, de cermet carbure et de nickel. L'écrasement des particules est ensuite abordé avec les problèmes de réactions chimiques, de trempe ultra-rapide et donc de structure cristalline des dépôts, d'adhdsion mais aussi de containtes résiduelles et de leur contrôle via les gradients de température dans les dépôts pendant le tir. Enfin quelques applications actuelles sont pr

Fissuration en relaxation des aciers inoxydables austénitiques au voisinage des soudures

NASA Astrophysics Data System (ADS)

Auzoux, Q.; Allais, L.; Gourgues, A. F.; Pineau, A.

2003-03-01

Des fissures intergranulaires peuvent se développer au voisinage des soudures des aciers inoxydables austénitiques lorsqu'ils sont réchauffés dans le domaine de température compris entre 500^{circ}C et 700^{circ}C. A ces températures, les contraintes résiduelles post-soudage se relaxent par déformation viscoplastique. Il peut arriver que ces zones proches de la soudure soient tellement fragiles, qu'elles ne puissent accommoder cette faible déformation. Afin de préciser quelles peuvent être les modifications microstructurales qui conduisent à une telle fragilisation, on a examiné les microstructures de ces zones et révélé ainsi un écrouissage résiduel, responsable d'une forte élévation de la dureté. On a pu reproduire par hypertrempe puis laminage entre 400^{circ}C et 600^{circ}C une microstructure similaire. Des essais mécaniques (traction, fluage, relaxation, sur éprouvettes lisses et pré-fissurées) ont été réalisés à 550^{circ}C et à 600^{circ}C sur ces zones affectées simulées et sur un état de référence hypertrempé. Ils ont montré que l'écrouissage diminuait la ductilité dans le domaine de rupture intergranulaire, sans modifier qualitativement le mécanisme d'endommagement. Pendant la pré-déformation les incompatibilités de déformation entre grains conduiraient à l'existence de contraintes locales élevées qui favoriseraient la germination des cavités intergranulaires.

40 CFR 60.62 - Standard for particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... particulate matter in excess of 0.15 kg per metric ton of feed (dry basis) to the kiln (0.30 lb per ton). (2... subpart shall cause to be discharged into the atmosphere from any clinker cooler any gases which: (1) Contain particulate matter in excess of 0.050 kg per metric ton of feed (dry basis) to the kiln (0.10 lb...

Comparaison des effets des irradiations γ, X et UV dans les fibres optiques

NASA Astrophysics Data System (ADS)

Girard, S.; Ouerdane, Y.; Baggio, J.; Boukenter, A.; Meunier, J.-P.; Leray, J.-L.

2005-06-01

Les fibres optiques présentent de nombreux avantages incitant à les intégrer dans des applications devant résister aux environnements radiatifs associés aux domaines civil, spatial ou militaire. Cependant, leur exposition à un rayonnement entraîne la création de défauts ponctuels dans la silice amorphe pure ou dopée qui constitue les différentes parties de la fibre optique. Ces défauts causent, en particulier, une augmentation transitoire de l'atténuation linéique des fibres optiques responsable de la dégradation voire de la perte du signal propagé dans celles-ci. Dans cet article, nous comparons les effets de deux types d'irradiation: une impulsion X et une dose γ cumulée. Les effets de ces irradiations sont ensuite comparés avec ceux induits par une insolation ultraviolette (244 nm) sur les propriétés d'absorption des fibres optiques. Nous montrons qu'il existe des similitudes entre ces différentes excitations et qu'il est possible, sous certaines conditions, d'utiliser celles-ci afin d'évaluer la capacité de certaines fibres optiques à fonctionner dans un environnement nucléaire donné.

A New Remote-Sensing Method for Mine Detection using HPM Irradiation and IR Detection.

DTIC Science & Technology

1999-12-01

absorption of microwave energy by the mine. This signature appears at the soil surface after a brief time-delay from the start of HPM illumination. At...detection de cible, l’operation de teledetection, la capacite de detecter des cibles sous un ciel couvert avec peu de dependance du cycle solaire et la...the temperature of the sample depends on the microwave energy absorbed by the sample and varies inversely with the sample thermal heat capacity. The

The importance of particulate texture to the flow strength of ice + dust

USGS Publications Warehouse

W. B. Durham,; N. Golding,; Stern, Laura A.; A. Pathare,; D. L. Goldsby,; D. Prior,

2015-01-01

Preliminary experimental surveys of the flow of dilute mixtures of ice plus hard particulates under planetary conditions indicate a strengthening effect with respect to pure ice, but with dependencies on environmental conditions (temperature, stress, grain size) that vary widely from study to study [1-4]. With the expectation that the textural character of the particulate fraction (size, shape, spatial distribution of particulates; relationship of particulates to ice grain boundaries, etc.) also influences rheological behavior, we have begun a more systematic investigation of the effect of particulates on strength. We rely extensively on cryogenic scanning electron microscopy (CSEM) and to maximize planetary relevance we focus on behavior at low stress and small grain size.

Vers des boites quantiques a base de graphene

NASA Astrophysics Data System (ADS)

Branchaud, Simon

Le graphene est un materiau a base de carbone qui est etudie largement depuis 2004. De tres nombreux articles ont ete publies tant sur les proprietes electroniques, qu'optiques ou mecaniques de ce materiel. Cet ouvrage porte sur l'etude des fluctuations de conductance dans le graphene, et sur la fabrication et la caracterisation de nanostructures gravees dans des feuilles de ce cristal 2D. Des mesures de magnetoresistance a basse temperature ont ete faites pres du point de neutralite de charge (PNC) ainsi qu'a haute densite electronique. On trouve deux origines aux fluctuations de conductance pres du PNC, soit des oscillations mesoscopiques provenant de l'interference quantique, et des fluctuations dites Hall quantique apparaissant a plus haut champ (>0.5T), semblant suivre les facteurs de remplissage associes aux monocouches de graphene. Ces dernieres fluctuations sont attribuees a la charge d'etats localises, et revelent un precurseur a l'effet Hall quantique, qui lui, ne se manifeste pas avant 2T. On arrive a extraire les parametres caracterisant l'echantillon a partir de ces donnees. A la fin de cet ouvrage, on effectue des mesures de transport dans des constrictions et ilots de graphene, ou des boites quantiques sont formees. A partir de ces mesures, on extrait les parametres importants de ces boites quantiques, comme leur taille et leur energie de charge.

Analysis of microsize particulates

NASA Technical Reports Server (NTRS)

Blanchard, M. B.; Farlow, N. H.; Ferry, G. V.

1972-01-01

Unique methods for analyzing individual particles ranging in size from 0.01 to 1000 micrometers have been developed for investigation of nature of cosmic dust. Methods are applicable to particulate aerosols and contaminants characteristically encountered in studies of air pollution and in experiments designed to abate pollution.

Prise en charge des troubles de consommation d’opioïdes en première ligne

PubMed Central

Srivastava, Anita; Kahan, Meldon; Nader, Maya

2017-01-01

Résumé Objectif Conseiller les médecins quant aux options thérapeutiques à recommander à des populations précises de patients : approche axée sur l’abstinence, traitement d’entretien par la buprénorphine-naloxone ou traitement d’entretien par la méthadone. Sources d’information Une recherche sur PubMed a été effectuée, et on a relevé dans les publications les données sur l’efficacité, l’innocuité et le profil d’effets indésirables de l’approche axée sur l’abstinence, du traitement par la buprénorphine-naloxone et du traitement par la méthadone. Les études d’observation et interventionnelles ont été incluses. Message principal La méthadone et la buprénorphine-naloxone sont substantiellement plus efficaces que l’approche axée sur l’abstinence. La méthadone présente un taux de rétention plus élevé que la buprénorphine-naloxone, alors que la buprénorphine-naloxone présente un risque plus faible de surdose. Les médecins devraient recommander le traitement par la méthadone ou la buprénorphine-naloxone plutôt que l’approche axée sur l’abstinence, et ce, à tous les groupes de patients (données de niveau I). La méthadone est préférable à la buprénorphine-naloxone chez les patients qui présentent un risque élevé d’abandon, comme les usagers d’opioïdes par injection (données de niveau I). Les jeunes et les femmes enceintes qui font usage d’opioïdes par injection devraient aussi recevoir la méthadone d’abord (données de niveau III). Si la buprénorphine-naloxone est prescrite en premier, il faut faire passer rapidement le patient à la méthadone si les symptômes de sevrage, les fortes envies ou la consommation d’opioïdes persistent malgré une dose optimale de buprénorphine-naloxone (données de niveau II). La buprénorphine-naloxone est recommandée chez les usagers d’opioïdes sur ordonnance par voie orale socialement stables, surtout s’ils ont un emploi ou si leurs

Regenerable particulate filter

DOEpatents

Stuecker, John N [Albuquerque, NM; Cesarano, III, Joseph; Miller, James E [Albuquerque, NM

2009-05-05

A method of making a three-dimensional lattice structure, such as a filter used to remove particulates from a gas stream, where the physical lattice structure is designed utilizing software simulation from pre-defined mass transfer and flow characteristics and the designed lattice structure is fabricated using a free-form fabrication manufacturing technique, where the periodic lattice structure is comprised of individual geometric elements.

Detection and Genome Analysis of a Lineage III Peste Des Petits Ruminants Virus in Kenya in 2011.

PubMed

Dundon, W G; Kihu, S M; Gitao, G C; Bebora, L C; John, N M; Oyugi, J O; Loitsch, A; Diallo, A

2017-04-01

In May 2011 in Turkana County, north-western Kenya, tissue samples were collected from goats suspected of having died of peste des petits ruminant (PPR) disease, an acute viral disease of small ruminants. The samples were processed and tested by reverse transcriptase PCR for the presence of PPR viral RNA. The positive samples were sequenced and identified as belonging to peste des petits ruminants virus (PPRV) lineage III. Full-genome analysis of one of the positive samples revealed that the virus causing disease in Kenya in 2011 was 95.7% identical to the full genome of a virus isolated in Uganda in 2012 and that a segment of the viral fusion gene was 100% identical to that of a virus circulating in Tanzania in 2013. These data strongly indicate transboundary movement of lineage III viruses between Eastern Africa countries and have significant implications for surveillance and control of this important disease as it moves southwards in Africa. © 2015 Blackwell Verlag GmbH.