Science.gov

Sample records for diode laser avaliacao

  1. Laser Diode Ignition (LDI)

    NASA Technical Reports Server (NTRS)

    Kass, William J.; Andrews, Larry A.; Boney, Craig M.; Chow, Weng W.; Clements, James W.; Merson, John A.; Salas, F. Jim; Williams, Randy J.; Hinkle, Lane R.

    1994-01-01

    This paper reviews the status of the Laser Diode Ignition (LDI) program at Sandia National Labs. One watt laser diodes have been characterized for use with a single explosive actuator. Extensive measurements of the effect of electrostatic discharge (ESD) pulses on the laser diode optical output have been made. Characterization of optical fiber and connectors over temperature has been done. Multiple laser diodes have been packaged to ignite multiple explosive devices and an eight element laser diode array has been recently tested by igniting eight explosive devices at predetermined 100 ms intervals.

  2. Laser diode protection circuit

    SciTech Connect

    Burgyan, L.; Hand, W.L.

    1990-05-08

    This patent describes a method for protecting a laser diode included within an electro-optical circuit. It comprises: the laser diode, a DC bias supply for supplying forward conduction current to the laser diode to cause it to emit light energy at a predetermined quiescent operating point, and an RF amplifier means for supplying an RF amplitude of an analog modulating signal to the laser diode for modulating the intensity of the emitted light energy about the quiescent operating point thereof, the method including providing a very high impedance to the laser diode during its nominal operating conditions about the quiescent point and, sensing an instantaneous amplitude of the RF amplitude modulating signal to detect amplitude surges therein, and responding to the sensing means by removing forward conduction current from the laser diode during the sense amplitude surges int he RF amplitude of the analog modulating signal, thereby causing the laser diode to reduce emission of light energy to a safe level.

  3. Diode laser applications in urology

    NASA Astrophysics Data System (ADS)

    Sam, Richard C.; Esch, Victor C.

    1995-05-01

    Diode lasers are air-cooled, efficient, compact devices which have the potential of very low cost when produced in quantity. The characteristics of diode lasers are discussed. Their applications in interstitial thermal treatment of the prostate, and laser ablation of prostate tissues, will be presented.

  4. Making an ultrastable diode laser

    NASA Astrophysics Data System (ADS)

    Archibald, James; Washburn, Matt; van Zijll, Marshall; Erickson, Christopher; Neyenhuis, Brian; Doermann, Greg; Durfee, Dallin

    2006-10-01

    We have constructed a 657nm diode laser with excellent stability for use in an atom interferometer. The laser is a grating-stabilized diode laser is locked to a high-finesse cavity using the Pound-Drever-Hall method. We have measured a linewidth of about 1 kHz and are working on several improvements which should further reduce our linewidth.

  5. Diode Laser Arrays

    NASA Astrophysics Data System (ADS)

    Botez, Dan; Scifres, Don R.

    1994-08-01

    This book provides a comprehensive overview of the fundamental principles and applications of semiconductor diode laser arrays. All of the major types of arrays are discussed in detail, including coherent, incoherent, edge- and surface-emitting, horizontal- and vertical-cavity, individually addressed, lattice- matched and strained-layer systems. The initial chapters cover such topics as lasers, amplifiers, external-cavity control, theoretical modeling, and operational dynamics. Spatially incoherent arrays are then described in detail, and the uses of vertical-cavity surface emitter and edge-emitting arrays in parallel optical-signal processing and multi-channel optical recording are discussed. Researchers and graduate students in solid state physics and electrical engineering studying the properties and applications of such arrays will find this book invaluable.

  6. Laser diode array and transmission optics

    NASA Technical Reports Server (NTRS)

    Kwon, Jin H.

    1989-01-01

    Information on laser diode array and transmission optics is given in viewgraph form. Information is given on coherent combining of laser diode arrays, amplification through a laser diode array, the far field pattern of a laser diode transmitter, and beam diameter at receiver vs. transmission distance.

  7. Unstable resonator diode laser

    SciTech Connect

    Clark, G.L.

    1988-04-19

    In a semiconductor diode laser, a structure is described comprising: a generally planar active layer, across which a forward bias voltage is applied, cladding layers adjacent to the active layer, to confine light in a direction perpendicular to the active layer, and first and second facets; in which the first facet is curved to present a concave part-cylindrical reflective surface toward the active layer, and in which the second facet includes a curved portion presenting a convex part-cylindrical reflective surface toward the active layer and a planar portion that is non-reflective. The curvatures of the two curved surfaces have axes of curvature that are approximately perpendicular to the active layer, the curvatures being selected to form an unstable resonator, in which light is confined in a particular sense by the cladding layers and from which energy is out-coupled through the planar portion of the second facet.

  8. Enhanced vbasis laser diode package

    SciTech Connect

    Deri, Robert J.; Chen, Diana; Bayramian, Andy; Freitas, Barry; Kotovsky, Jack

    2014-08-19

    A substrate having an upper surface and a lower surface is provided. The substrate includes a plurality of v-grooves formed in the upper surface. Each v-groove includes a first side and a second side perpendicular to the first side. A laser diode bar assembly is disposed within each of the v-grooves and attached to the first side. The laser diode bar assembly includes a first adhesion layer disposed on the first side of the v-groove, a metal plate attached to the first adhesion layer, a second adhesion layer disposed over the metal plate, and a laser diode bar attached to the second adhesion layer. The laser diode bar has a coefficient of thermal expansion (CTE) substantially similar to that of the metal plate.

  9. Diode-pumped laser research

    NASA Technical Reports Server (NTRS)

    Ramos-Izquierdo, L.; Bufton, J. L.; Chan, K.

    1988-01-01

    The Laboratory for Oceans is currently working on the development of compact laser diode array (LD) pumped Nd:YAG lasers for use in space-based altimetry and ranging. Laser diode-array pumping technology promises to increase the electrical to optical efficiency of solid state lasers by an order of magnitude with a lifetime increase of nearly three orders of magnitude relative to today's conventional flashlamp-pumped laser systems. The small size, efficiency, and ruggedness make LD-pumped solid state lasers ideal for space based applications. In an in-house RTOP effort, a novel multiple-pass LD-pumped Nd:YAG laser amplifier was designed and tested to increase the 100 microjoule output pulse energy of the Lightwave laser oscillator. Preliminary results have yielded a round trip amplifier gain of about 15 percent using 7 microjoule LD-pump energy. As a parallel activity, funding was recently obtained to investigate the possible use of custom made fiber optic arrays to obtain an efficient optical coupling mechanism between the emitting laser diode-arrays and the target solid state laser material. Fiber optic coupling arrays would allow for the easy manipulation of the spatial emitting pattern of the diode pump sources to match either an end or side pumping laser configuration.

  10. Diode laser array

    NASA Technical Reports Server (NTRS)

    Carlson, Nils W. (Inventor); Evans, Gary A. (Inventor); Kaiser, Charlie J. (Inventor)

    1990-01-01

    A diode laser array comprises a substrate of a semiconductor material having first and second opposed surfaces. On the first surface is a plurality of spaced gain sections and a separate distributed Bragg reflector passive waveguide at each end of each gain section and optically connecting the gain sections. Each gain section includes a cavity therein wherein charge carriers are generated and recombine to generate light which is confined in the cavity. Also, the cavity, which is preferably a quantum well cavity, provides both a high differential gain and potentially large depth of loss modulation. Each waveguide has a wavelength which is preferably formed by an extension of the cavity of the gain sections and a grating. The grating has a period which provides a selective feedback of light into the gain sections to supporting lasing, which allows some of the light to be emitted from the waveguide normal to the surface of the substrate and which allows optical coupling of the gain sections. Also, the grating period provides an operating wavelength which is on the short wavelength side of the gain period of the gain sections required for laser oscillation. An RF pulse is applied so as to maximize the magnitude of the loss modulation and the differential gain in the gain sections. The array is operated by applying a DC bias to all the gain sections at a level just below the threshold of the gain sections to only one of the gain sections which raises the bias in all of the gain sections to a level that causes all of the gain sections to oscillate. Thus, a small bias can turn the array on and off.

  11. New laser materials for laser diode pumping

    NASA Technical Reports Server (NTRS)

    Jenssen, H. P.

    1990-01-01

    The potential advantages of laser diode pumped solid state lasers are many with high overall efficiency being the most important. In order to realize these advantages, the solid state laser material needs to be optimized for diode laser pumping and for the particular application. In the case of the Nd laser, materials with a longer upper level radiative lifetime are desirable. This is because the laser diode is fundamentally a cw source, and to obtain high energy storage, a long integration time is necessary. Fluoride crystals are investigated as host materials for the Nd laser and also for IR laser transitions in other rare earths, such as the 2 micron Ho laser and the 3 micron Er laser. The approach is to investigate both known crystals, such as BaY2F8, as well as new crystals such as NaYF8. Emphasis is on the growth and spectroscopy of BaY2F8. These two efforts are parallel efforts. The growth effort is aimed at establishing conditions for obtaining large, high quality boules for laser samples. This requires numerous experimental growth runs; however, from these runs, samples suitable for spectroscopy become available.

  12. Quantum Noise in Laser Diodes

    NASA Technical Reports Server (NTRS)

    Giacobino, E.; Marin, F.; Bramati, A.; Jost, V.; Poizat, J. Ph.; Roch, J.-F.; Grangier, P.; Zhang, T.-C.

    1996-01-01

    We have investigated the intensity noise of single mode laser diodes, either free-running or using different types of line narrowing techniques at room temperature. We have measured an intensity squeezing of 1.2 dB with grating-extended cavity lasers and 1.4 dB with injection locked lasers (respectively 1.6 dB and 2.3 dB inferred at the laser output). We have observed that the intensity noise of a free-running nominally single mode laser diode results from a cancellation effect between large anti-correlated fluctuations of the main mode and of weak longitudinal side modes. Reducing the side modes by line narrowing techniques results in intensity squeezing.

  13. IC Fabrication Methods Improve Laser Diodes

    NASA Technical Reports Server (NTRS)

    Miller, M.; Pickhardt, V.

    1984-01-01

    Family of high-performance, tunable diode lasers developed for use as local oscillators in passive laser heterodyne spectrometer. Diodes fabricated using standard IC processes include photolithography, selective etching and vacuum deposition of metals and insulators. Packaging refinements improved thermal-cycling characteristics of diodes and increased room-temperature shelf life.

  14. Broad interband semiconductor laser diodes

    NASA Astrophysics Data System (ADS)

    Tan, Chee Loon

    A semiconductor laser is a diode device that emits light via stimulated emission. Conventionally, light emitted from a semiconductor laser is spatially coherent or narrowband. The fundamental mechanism of stimulated emission process in general leads only to a single wavelength emission. However, there are some lasers emit light with a broad spectrum or different distinct wavelength subjected to various operating conditions such as external grating configuration with semiconductor laser, diode-pumped self-Q-switch fiber laser, ultrashort pulse excitation, photonic crystal fiber, ultrabroadband solid-state lasers, semiconductor optical amplifier-based multiwavelength tunable fiber lasers, nonlinear crystal, broadband semiconductor laser etc. This type of broadband laser is vital in many practical applications such as optical telecommunications, spectroscopy measurement, imaging technology, etc. Recently, an ultra-broadband semiconductor laser that utilizes intersubband optical transitions via quantum cascade configuration has been realized. Laser action with a Fabry-Perot spectrum covering all wavelengths from 6 to 8 microm simultaneously is demonstrated with this approach. More recently, broadband emission results from interband optical transitions via quantum-dot/dash nanostructures have been demonstrated in a simple p-i-n laser diode structure. To date, this latest approach offers the simplest design by proper engineering of quantized energy states as well as utilizing the high inhomogeneity of the dot/dash nanostructures, which is inherent from self-assembled growth technology. In this dissertation, modeling of semiconductor InGaAs/GaAs quantum-dot broadband laser utilizing the properties of inhomogeneous and homogeneous broadening effects on lasing spectral will be discussed, followed by a detail analysis of another type of broad interband semiconductor laser, which is InAs/InGaAlAs quantum-dash broadband laser. Based on the device characterization results

  15. Self-Injection Locking Of Diode Lasers

    NASA Technical Reports Server (NTRS)

    Hemmati, H.

    1991-01-01

    Simple optical coupling scheme locks array of gain-guided diode lasers into oscillation in single mode and with single-lobed output beam. Selective feedback from thin etalon self-injection-locks array into desired mode. One application of new scheme for pumping of neodymium: yttrium aluminum garnet lasers with diode-laser arrays.

  16. Schlieren with a laser diode source

    NASA Technical Reports Server (NTRS)

    Burner, A. W.; Franke, J. M.

    1981-01-01

    The use of a laser diode as a light source for a schlieren system designed to study phase objects such as a wind-tunnel flow is explored. A laser diode schlieren photograph and a white light schlieren photograph (zirconium arc source) are presented for comparison. The laser diode has increased sensitivity, compared with light schlieren, without appreciable image degradiation, and is an acceptable source for schlieren flow visualization.

  17. Physics and applications of laser diode chaos

    NASA Astrophysics Data System (ADS)

    Sciamanna, M.; Shore, K. A.

    2015-03-01

    This Review Article provides an overview of chaos in laser diodes by surveying experimental achievements in the area and explaining the theory behind the phenomenon. The fundamental physics underpinning laser diode chaos and also the opportunities for harnessing it for potential applications are discussed. The availability and ease of operation of laser diodes, in a wide range of configurations, make them a convenient testbed for exploring basic aspects of nonlinear and chaotic dynamics. It also makes them attractive for practical tasks, such as chaos-based secure communications and random number generation. Avenues for future research and development of chaotic laser diodes are also identified.

  18. Effects of radiation on laser diodes.

    SciTech Connect

    Phifer, Carol Celeste

    2004-09-01

    The effects of ionizing and neutron radiation on the characteristics and performance of laser diodes are reviewed, and the formation mechanisms for nonradiative recombination centers, the primary type of radiation damage in laser diodes, are discussed. Additional topics include the detrimental effects of aluminum in the active (lasing) volume, the transient effects of high-dose-rate pulses of ionizing radiation, and a summary of ways to improve the radiation hardness of laser diodes. Radiation effects on laser diodes emitting in the wavelength region around 808 nm are emphasized.

  19. Grating rhomb diode laser power combiner

    NASA Technical Reports Server (NTRS)

    Minott, Peter O.; Abshire, James B.

    1987-01-01

    A compact device for spectrally combining many laser-diode beams into a single multi-wavelength beam has been developed for use in NASA's intersatellite communications programs. The prototype device combines seven 30 milliwatt beams into a single beam with 70 percent efficiency producing an output of approximately 150 milliwatts. All beams are coaxial and can be collimated with a single transmitter optical system. The combining technique is relatively insensitive to drifts in the laser-diode wavelength and provides both increased power output and laser-diode source redundancy. Combination of more than 100 laser-diodes producing an output greater than 5 watts appears feasible with this technique.

  20. Laser diode package with enhanced cooling

    DOEpatents

    Deri, Robert J.; Kotovsky, Jack; Spadaccini, Christopher M.

    2012-06-12

    A laser diode package assembly includes a reservoir filled with a fusible metal in close proximity to a laser diode. The fusible metal absorbs heat from the laser diode and undergoes a phase change from solid to liquid during the operation of the laser. The metal absorbs heat during the phase transition. Once the laser diode is turned off, the liquid metal cools off and resolidifies. The reservoir is designed such that that the liquid metal does not leave the reservoir even when in liquid state. The laser diode assembly further includes a lid with one or more fin structures that extend into the reservoir and are in contact with the metal in the reservoir.

  1. Laser diode package with enhanced cooling

    DOEpatents

    Deri, Robert J.; Kotovsky, Jack; Spadaccini, Christopher M.

    2012-06-26

    A laser diode package assembly includes a reservoir filled with a fusible metal in close proximity to a laser diode. The fusible metal absorbs heat from the laser diode and undergoes a phase change from solid to liquid during the operation of the laser. The metal absorbs heat during the phase transition. Once the laser diode is turned off, the liquid metal cools off and resolidifies. The reservoir is designed such that that the liquid metal does not leave the reservoir even when in liquid state. The laser diode assembly further includes a lid with one or more fin structures that extend into the reservoir and are in contact with the metal in the reservoir.

  2. Laser diode package with enhanced cooling

    DOEpatents

    Deri, Robert J.; Kotovsky, Jack; Spadaccini, Christopher M.

    2011-09-13

    A laser diode package assembly includes a reservoir filled with a fusible metal in close proximity to a laser diode. The fusible metal absorbs heat from the laser diode and undergoes a phase change from solid to liquid during the operation of the laser. The metal absorbs heat during the phase transition. Once the laser diode is turned off, the liquid metal cools off and resolidifies. The reservoir is designed such that that the liquid metal does not leave the reservoir even when in liquid state. The laser diode assembly further includes a lid with one or more fin structures that extend into the reservoir and are in contact with the metal in the reservoir.

  3. Hermetic diode laser transmitter module

    NASA Astrophysics Data System (ADS)

    Ollila, Jyrki; Kautio, Kari; Vahakangas, Jouko; Hannula, Tapio; Kopola, Harri K.; Oikarinen, Jorma; Sivonen, Matti

    1999-04-01

    In very demanding optoelectronic sensor applications it is necessary to encapsulate semiconductor components hermetically in metal housings to ensure reliable operation of the sensor. In this paper we report on the development work to package a laser diode transmitter module for a time- off-light distance sensor application. The module consists of a lens, laser diode, electronic circuit and optomechanics. Specifications include high acceleration, -40....+75 degree(s)C temperature range, very low gas leakage and mass-production capability. We have applied solder glasses for sealing optical lenses and electrical leads hermetically into a metal case. The lens-metal case sealing has been made by using a special soldering glass preform preserving the optical quality of the lens. The metal housings are finally sealed in an inert atmosphere by welding. The assembly concept to retain excellent optical power and tight optical axis alignment specifications is described. The reliability of the laser modules manufactured has been extensively tested using different aging and environmental test procedures. Sealed packages achieve MIL- 883 standard requirements for gas leakage.

  4. Diode Lasers and Practical Trace Analysis.

    ERIC Educational Resources Information Center

    Imasaka, Totaro; Nobuhiko, Ishibashi

    1990-01-01

    Applications of lasers to molecular absorption spectrometry, molecular fluorescence spectrometry, visible semiconductor fluorometry, atomic absorption spectrometry, and atomic fluorescence spectrometry are discussed. Details of the use of the frequency-doubled diode laser are provided. (CW)

  5. Diode-pumped CW molecular lasers

    NASA Astrophysics Data System (ADS)

    Wellegehausen, B.; Luhs, W.

    2016-05-01

    First continuous laser oscillation on many lines in the range of 533-635 nm on different transitions of Na2 and Te2 molecules has been obtained, optically pumped with common cw blue emitting InGaN diode lasers operating around 445 and 460 nm. Spectral narrowing of the diode laser is achieved with a beamsplitter and grating setup, allowing use of more than 50 % of the diode power. Operation conditions and properties of the laser systems are presented, and perspectives for the realization of compact low cost molecular lasers are discussed.

  6. Diode lasers: From laboratory to industry

    NASA Astrophysics Data System (ADS)

    Nasim, Hira; Jamil, Yasir

    2014-03-01

    The invention of first laser in 1960 triggered the discovery of several new families of lasers. A rich interplay of different lasing materials resulted in a far better understanding of the phenomena particularly linked with atomic and molecular spectroscopy. Diode lasers have gone through tremendous developments on the forefront of applied physics that have shown novel ways to the researchers. Some interesting attributes of the diode lasers like cost effectiveness, miniature size, high reliability and relative simplicity of use make them good candidates for utilization in various practical applications. Diode lasers are being used by a variety of professionals and in several spectroscopic techniques covering many areas of pure and applied sciences. Diode lasers have revolutionized many fields like optical communication industry, medical science, trace gas monitoring, studies related to biology, analytical chemistry including elemental analysis, war fare studies etc. In this paper the diode laser based technologies and measurement techniques ranging from laboratory research to automated field and industry have been reviewed. The application specific developments of diode lasers and various methods of their utilization particularly during the last decade are discussed comprehensively. A detailed snapshot of the current state of the art diode laser applications is given along with a detailed discussion on the upcoming challenges.

  7. Improved Thermoelectrically Cooled Laser-Diode Assemblies

    NASA Technical Reports Server (NTRS)

    Glesne, Thomas R.; Schwemmer, Geary K.; Famiglietti, Joe

    1994-01-01

    Cooling decreases wavelength and increases efficiency and lifetime. Two improved thermoelectrically cooled laser-diode assemblies incorporate commercial laser diodes providing combination of both high wavelength stability and broad wavelength tuning which are broadly tunable, highly stable devices for injection seeding of pulsed, high-power tunable alexandrite lasers used in lidar remote sensing of water vapor at wavelengths in vicinity of 727 nanometers. Provide temperature control needed to take advantage of tunability of commercial AlGaAs laser diodes in present injection-seeding application.

  8. Frequency stabilization of diode-laser-pumped solid state lasers

    NASA Technical Reports Server (NTRS)

    Byer, Robert L.

    1988-01-01

    The goal of the NASA Sunlite program is to fly two diode-laser-pumped solid-state lasers on the space shuttle and while doing so to perform a measurement of their frequency stability and temporal coherence. These measurements will be made by combining the outputs of the two lasers on an optical radiation detector and spectrally analyzing the beat note. Diode-laser-pumped solid-state lasers have several characteristics that will make them useful in space borne experiments. First, this laser has high electrical efficiency. Second, it is of a technology that enables scaling to higher powers in the future. Third, the laser can be made extremely reliable, which is crucial for many space based applications. Fourth, they are frequency and amplitude stable and have high temporal coherence. Diode-laser-pumped solid-state lasers are inherently efficient. Recent results have shown 59 percent slope efficiency for a diode-laser-pumped solid-state laser. As for reliability, the laser proposed should be capable of continuous operation. This is possible because the diode lasers can be remote from the solid state gain medium by coupling through optical fibers. Diode lasers are constructed with optical detectors for monitoring their output power built into their mounting case. A computer can actively monitor the output of each diode laser. If it sees any variation in the output power that might indicate a problem, the computer can turn off that diode laser and turn on a backup diode laser. As for stability requirements, it is now generally believed that any laser can be stabilized if the laser has a frequency actuator capable of tuning the laser frequency as far as it is likely to drift in a measurement time.

  9. Diode-pumped dysprosium laser materials

    NASA Astrophysics Data System (ADS)

    Bowman, S. R.; Condon, N. J.; O'Connor, S.; Rosenberg, A.

    2009-05-01

    We are investigating materials for direct blue solid-state lasers assuming UV excitation with GaN based laser diodes. Room temperature spectroscopy is reported relevant to a proposed quasi-three level laser from the 4F9/2 level in trivalent dysprosium. Modeling based on these measurements suggests this is a promising new laser transition.

  10. Diode laser (980nm) cartilage reshaping

    NASA Astrophysics Data System (ADS)

    El Kharbotly, A.; El Tayeb, T.; Mostafa, Y.; Hesham, I.

    2011-03-01

    Loss of facial or ear cartilage due to trauma or surgery is a major challenge to the otolaryngologists and plastic surgeons as the complicated geometric contours are difficult to be animated. Diode laser (980 nm) has been proven effective in reshaping and maintaining the new geometric shape achieved by laser. This study focused on determining the optimum laser parameters needed for cartilage reshaping with a controlled water cooling system. Harvested animal cartilages were angulated with different degrees and irradiated with different diode laser powers (980nm, 4x8mm spot size). The cartilage specimens were maintained in a deformation angle for two hours after irradiation then released for another two hours. They were serially measured and photographed. High-power Diode laser irradiation with water cooling is a cheep and effective method for reshaping the cartilage needed for reconstruction of difficult situations in otorhinolaryngologic surgery. Key words: cartilage,diode laser (980nm), reshaping.

  11. Diode-pumped laser altimeter

    NASA Technical Reports Server (NTRS)

    Welford, D.; Isyanova, Y.

    1993-01-01

    TEM(sub 00)-mode output energies up to 22.5 mJ with 23 percent slope efficiencies were generated at 1.064 microns in a diode-laser pumped Nd:YAG laser using a transverse-pumping geometry. 1.32-micron performance was equally impressive at 10.2 mJ output energy with 15 percent slope efficiency. The same pumping geometry was successfully carried forward to several complex Q-switched laser resonator designs with no noticeable degradation of beam quality. Output beam profiles were consistently shown to have greater than 90 percent correlation with the ideal TEM(sub 00)-order Gaussian profile. A comparison study on pulse-reflection-mode (PRM), pulse-transmission-mode (PTM), and passive Q-switching techniques was undertaken. The PRM Q-switched laser generated 8.3 mJ pulses with durations as short as 10 ns. The PTM Q-switch laser generated 5 mJ pulses with durations as short as 5 ns. The passively Q-switched laser generated 5 mJ pulses with durations as short as 2.4 ns. Frequency doubling of both 1.064 microns and 1.32 microns with conversion efficiencies of 56 percent in lithium triborate and 10 percent in rubidium titanyl arsenate, respectively, was shown. Sum-frequency generation of the 1.064 microns and 1.32 microns radiations was demonstrated in KTP to generate 1.1 mJ of 0.589 micron output with 11.5 percent conversion efficiency.

  12. Integrated injection-locked semiconductor diode laser

    DOEpatents

    Hadley, G.R.; Hohimer, J.P.; Owyoung, A.

    1991-02-19

    A continuous wave integrated injection-locked high-power diode laser array is provided with an on-chip independently-controlled master laser. The integrated injection locked high-power diode laser array is capable of continuous wave lasing in a single near-diffraction limited output beam at single-facet power levels up to 125 mW (250 mW total). Electronic steering of the array emission over an angle of 0.5 degrees is obtained by varying current to the master laser. The master laser injects a laser beam into the slave array by reflection of a rear facet. 18 figures.

  13. Integrated injection-locked semiconductor diode laser

    DOEpatents

    Hadley, G. Ronald; Hohimer, John P.; Owyoung, Adelbert

    1991-01-01

    A continuous wave integrated injection-locked high-power diode laser array is provided with an on-chip independently-controlled master laser. The integrated injection locked high-power diode laser array is capable of continuous wave lasing in a single near-diffraction limited output beam at single-facet power levels up to 125 mW (250 mW total). Electronic steering of the array emission over an angle of 0.5 degrees is obtained by varying current to the master laser. The master laser injects a laser beam into the slave array by reflection of a rear facet.

  14. Laterally injected light-emitting diode and laser diode

    DOEpatents

    Miller, Mary A.; Crawford, Mary H.; Allerman, Andrew A.

    2015-06-16

    A p-type superlattice is used to laterally inject holes into an III-nitride multiple quantum well active layer, enabling efficient light extraction from the active area. Laterally-injected light-emitting diodes and laser diodes can enable brighter, more efficient devices that impact a wide range of wavelengths and applications. For UV wavelengths, applications include fluorescence-based biological sensing, epoxy curing, and water purification. For visible devices, applications include solid state lighting and projection systems.

  15. Very high brightness diode laser

    NASA Astrophysics Data System (ADS)

    Heinemann, Stefan; Lewis, Ben; Michaelis, Karsten; Schmidt, Torsten

    2012-03-01

    Multiple Single Emitter (MSE) modules allow highest power and highest brightness diode lasers based on standard broad area diodes. 12 single emitters, each rated at 11 W, are stacked in fast axis and with polarization multiplexing 200W are achieved in a fully collimated beam with a beam quality of 7mm*mrad in both axes. Volume Bragg Gratings (VBG) stabilize the wavelength and narrow the linewidth to less than 2nm. Dichroic mirrors are used for dense wavelength multiplexing of 4 channels within 12 nm. 400W are measured from a 0.2 mm fiber, 0.1 NA. Control and drive electronics are integrated into the 200 W platform and represent a basic building block for a variety of applications, such as a flexible turn key system comprising 12 MSE modules. An integrated beam switch directs the light in six 100 μm, or in one 0.2 mm and one 0.1 mm fiber. 800W are measured from the six 0.1 mm fibers and 700W from the 0.2 mm fiber. The technologies can be transferred to other wavelengths to include 793 nm and 1530 nm. Narrow line gratings and optimized spectral combining enable further improvements in spectral brightness and power.

  16. Percutaneous diode laser disc nucleoplasty

    NASA Astrophysics Data System (ADS)

    Menchetti, P. P.; Longo, Leonardo

    2004-09-01

    The treatment of herniated disc disease (HNP) over the years involved different miniinvasive surgical options. The classical microsurgical approach has been substituted over the years both by endoscopic approach in which is possible to practice via endoscopy a laser thermo-discoplasty, both by percutaneous laser disc nucleoplasty. In the last ten years, the percutaneous laser disc nucleoplasty have been done worldwide in more than 40000 cases of HNP. Because water is the major component of the intervertebral disc, and in HNP pain is caused by the disc protrusion pressing against the nerve root, a 980 nm Diode laser introduced via a 22G needle under X-ray guidance and local anesthesia, vaporizes a small amount of nucleous polposus with a disc shrinkage and a relief of pressure on nerve root. Most patients get off the table pain free and are back to work in 5 to 7 days. Material and method: to date, 130 patients (155 cases) suffering for relevant symptoms therapy-resistant 6 months on average before consulting our department, have been treated. Eightyfour (72%) males and 46 (28%) females had a percutaneous laser disc nucleoplasty. The average age of patients operated was 48 years (22 - 69). The level of disc removal was L3/L4 in 12 cases, L4/L5 in 87 cases and L5/S1 in 56 cases. Two different levels were treated at the same time in 25 patients. Results: the success rate at a minimum follow-up of 6 months was 88% with a complication rate of 0.5%.

  17. Advanced laser diodes for sensing applications

    SciTech Connect

    VAWTER,GREGORY A.; MAR,ALAN; CHOW,WENG W.; ALLERMAN,ANDREW A.

    2000-01-01

    The authors have developed diode lasers for short pulse duration and high peak pulse power in the 0.01--100.0 m pulsewidth regime. A primary goal of the program was producing up to 10 W while maintaining good far-field beam quality and ease of manufacturability for low cost. High peak power, 17 W, picosecond pulses have been achieved by gain switching of flared geometry waveguide lasers and amplifiers. Such high powers area world record for this type of diode laser. The light emission pattern from diode lasers is of critical importance for sensing systems such as range finding and chemical detection. They have developed a new integrated optical beam transformer producing rib-waveguide diode lasers with a symmetric, low divergence, output beam and increased upper power limits for irreversible facet damage.

  18. A Diode Laser System for Synchronous Photoinjection

    SciTech Connect

    Poelker, M., Hansknecht, J.

    1997-12-31

    A laser system, which is composed of a gain switched diode seed laser and a single-pass diode optical amplifier, is used to drive the polarized electron source at Jefferson Lab. The system emits pulsed laser light synchronized to the accelerating cavity radio frequency (rf) at 1497 MHz or the third subharmonic, 499 MHz. The maximum average output power from the laser system is 500 mW and the optical pulse width is 60 to 80 ps. The laser system is compact and very reliable operating remotely for many days without attention.

  19. Arbitrary waveform generator to improve laser diode driver performance

    SciTech Connect

    Fulkerson, Jr, Edward Steven

    2015-11-03

    An arbitrary waveform generator modifies the input signal to a laser diode driver circuit in order to reduce the overshoot/undershoot and provide a "flat-top" signal to the laser diode driver circuit. The input signal is modified based on the original received signal and the feedback from the laser diode by measuring the actual current flowing in the laser diode after the original signal is applied to the laser diode.

  20. Analysis of phased-array diode lasers

    SciTech Connect

    Hardy, A.; Streifer, W.

    1985-07-01

    An improved, more accurate analysis of phased-array diode lasers is presented, which yields results that differ both qualitatively and quantitatively from those previously employed. A numerical example indicating decreased splitting in array mode gains is included.

  1. Blood sugar monitoring with laser diode

    NASA Astrophysics Data System (ADS)

    Zhang, Xiqin; Chen, Jianhong; Yeo, Joon Hock

    2006-09-01

    In this paper, the non-invasive measurement of blood sugar level was studied by use of near infrared laser diode. The in-vivo experiments were carried out using laser diodes with wavelength 1625nm and 1650nm. Several volunteers were tested before and after drinking glucose solution. We took blood from a fingertip and measured its concentration with a glucose meter while taking signal voltage from laser diode system. The signal voltage was processed by using a computer and blood absorption was obtained. The results show that blood sugar level and blood absorption have similar trends before and after drinking glucose solution. We also compared the trends of drinking glucose solution and pure water and the results show that the difference of blood absorption is obvious. From the results we can see that laser diode is suitable for blood glucose monitoring.

  2. High power diode pumped alkali vapor lasers

    NASA Astrophysics Data System (ADS)

    Zweiback, J.; Krupke, B.

    2008-05-01

    Diode pumped alkali lasers have developed rapidly since their first demonstration. These lasers offer a path to convert highly efficient, but relatively low brightness, laser diodes into a single high power, high brightness beam. General Atomics has been engaged in the development of DPALs with scalable architectures. We have examined different species and pump characteristics. We show that high absorption can be achieved even when the pump source bandwidth is several times the absorption bandwidth. In addition, we present experimental results for both potassium and rubidium systems pumped with a 0.2 nm bandwidth alexandrite laser. These data show slope efficiencies of 67% and 72% respectively.

  3. Narrowband alexandrite laser injection seeded with frequency dithered diode laser

    NASA Technical Reports Server (NTRS)

    Schwemmer, Geary; Lee, H. S.; Prasad, Coorg

    1991-01-01

    Narrowband radiation is produced from a pulsed alexandrite laser when injection seeded with the output of a low power, tunable, continuous wave single mode diode laser. Injection seeded power oscillators are easier to frequency stabilize than etalon narrowed lasers, are more efficient and less prone to optical damage. AlGaAs diode lasers are available with wavelengths from 760 to 770 nm in the oxygen A band that can be used for differential absorption lidar remote sensing of atmospheric pressure and temperature. Diodes with room temperature output at 740 nm may be cooled sufficiently to emit in the water vapor absorption band at 720-730 nm for humidity remote sensing. The diode laser linewidth of 200 MHz is sufficient to seed 2 or 3 longitudinal modes of the multi-transverse mode alexandrite laser, giving the pulsed laser a bandwidth of 0.007 to 0.014/cm.

  4. Composite resonator vertical cavity laser diode

    SciTech Connect

    Choquette, K.D.; Hou, H.Q.; Chow, W.W.; Geib, K.M.; Hammons, B.E.

    1998-05-01

    The use of two coupled laser cavities has been employed in edge emitting semiconductor lasers for mode suppression and frequency stabilization. The incorporation of coupled resonators within a vertical cavity laser opens up new possibilities due to the unique ability to tailor the interaction between the cavities. Composite resonators can be utilized to control spectral and temporal properties within the laser; previous studies of coupled cavity vertical cavity lasers have employed photopumped structures. The authors report the first composite resonator vertical cavity laser diode consisting of two optical cavities and three monolithic distributed Bragg reflectors. Cavity coupling effects and two techniques for external modulation of the laser are described.

  5. NASA direct detection laser diode driver

    NASA Technical Reports Server (NTRS)

    Seery, B. D.; Hornbuckle, C. A.

    1989-01-01

    TRW has developed a prototype driver circuit for GaAs laser diodes as part of the NASA/Goddard Space Flight Center's Direct Detection Laser Transceiver (DDLT) program. The circuit is designed to drive the laser diode over a range of user-selectable data rates from 1.7 to 220 Mbps, Manchester-encoded, while ensuring compatibility with 8-bit and quaternary pulse position modulation (QPPM) formats for simulating deep space communications. The resulting hybrid circuit has demonstrated 10 to 90 percent rise and fall times of less than 300 ps at peak currents exceeding 100 mA.

  6. Qualification and Selection of Flight Diode Lasers for Space Applications

    NASA Technical Reports Server (NTRS)

    Liebe, Carl C.; Dillon, Robert P.; Gontijo, Ivair; Forouhar, Siamak; Shapiro, Andrew A.; Cooper, Mark S.; Meras, Patrick L.

    2010-01-01

    The reliability and lifetime of laser diodes is critical to space missions. The Nuclear Spectroscopic Telescope Array (NuSTAR) mission includes a metrology system that is based upon laser diodes. An operational test facility has been developed to qualify and select, by mission standards, laser diodes that will survive the intended space environment and mission lifetime. The facility is situated in an electrostatic discharge (ESD) certified clean-room and consist of an enclosed temperature-controlled stage that can accommodate up to 20 laser diodes. The facility is designed to characterize a single laser diode, in addition to conducting laser lifetime testing on up to 20 laser diodes simultaneously. A standard laser current driver is used to drive a single laser diode. Laser diode current, voltage, power, and wavelength are measured for each laser diode, and a method of selecting the most adequate laser diodes for space deployment is implemented. The method consists of creating histograms of laser threshold currents, powers at a designated current, and wavelengths at designated power. From these histograms, the laser diodes that illustrate a performance that is outside the normal are rejected and the remaining lasers are considered spaceborne candidates. To perform laser lifetime testing, the facility is equipped with 20 custom laser drivers that were designed and built by California Institute of Technology specifically to drive NuSTAR metrology lasers. The laser drivers can be operated in constant-current mode or alternating-current mode. Situated inside the enclosure, in front of the laser diodes, are 20 power-meter heads to record laser power throughout the duration of lifetime testing. Prior to connecting a laser diode to the current source for characterization and lifetime testing, a background program is initiated to collect current, voltage, and resistance. This backstage data collection enables the operational test facility to have full laser diode

  7. Nd:YAG laser side pumped by diode laser arrays

    NASA Astrophysics Data System (ADS)

    Tan, Hua; Huang, Weiling; Zhou, Zhouyou; Wang, Hailin; Cao, Hongbing; Wang, Ying

    1999-09-01

    The major limitation of flashlamp-pumped solid-state lasers is the low overall efficiency. Replacing flashlamps with high power laser diodes allows an increase of system efficiency by over an order of magnitude. Because of the thermally induced stress fracture of the laser materials, power-scaling possibilities of end-pumped configurations are limited. Therefore side pump geometry has to be used for high power laser. The theory and the design of high power diode side-pumped Nd:YAG laser system is described. The Nd:YAG rod is side-pumped by diode laser arrays with wavelength at 808 nm. We analyze the result of our experiments and make some conclusions about the design of side-pumped laser.

  8. Phase Noise Reduction of Laser Diode

    NASA Technical Reports Server (NTRS)

    Zhang, T. C.; Poizat, J.-Ph.; Grelu, P.; Roch, J.-F.; Grangier, P.; Marin, F.; Bramati, A.; Jost, V.; Levenson, M. D.; Giacobino, E.

    1996-01-01

    Phase noise of single mode laser diodes, either free-running or using line narrowing technique at room temperature, namely injection-locking, has been investigated. It is shown that free-running diodes exhibit very large excess phase noise, typically more than 80 dB above shot-noise at 10 MHz, which can be significantly reduced by the above-mentioned technique.

  9. Diode-laser-based therapy device

    NASA Astrophysics Data System (ADS)

    Udrea, Mircea V.; Nica, Adriana S.; Florian, Mariana; Poenaru, Daniela; Udrea, Gabriela; Lungeanu, Mihaela; Sporea, Dan G.; Vasiliu, Virgil V.; Vieru, Roxana

    2004-10-01

    A new therapy laser device is presented. The device consists of a central unit and different types of laser probes. The laser probe model SL7-650 delivers seven red (650 nm), 5 mW diode lasers convergent beams. The beams converge at about 30 cm in front of the laser probe and the irradiated area might be varied by simple displacement of the laser probe with respect to the target. The laser probe SL1-808 emits single infrared laser beam up to 500 mW. The efficiency of the use of this device in physiotherapy, and rheumatology, has been put into evidence after years of testing. Dermatology and microsurgery are users of infrared powerful laser probes. The device has successfully passed technical and clinical tests in order to be certified. The laser device design and some medical results are given.

  10. Rugged, Tunable Extended-Cavity Diode Laser

    NASA Technical Reports Server (NTRS)

    Moore, Donald; Brinza, David; Seidel, David; Klipstein, William; Choi, Dong Ho; Le, Lam; Zhang, Guangzhi; Iniguez, Roberto; Tang, Wade

    2007-01-01

    A rugged, tunable extended-cavity diode laser (ECDL) has been developed to satisfy stringent requirements for frequency stability, notably including low sensitivity to vibration. This laser is designed specifically for use in an atomic-clock experiment to be performed aboard the International Space Station (ISS). Lasers of similar design would be suitable for use in terrestrial laboratories engaged in atomic-clock and atomic-physics research.

  11. Diode laser-pumped solid-state lasers

    NASA Technical Reports Server (NTRS)

    Fan, Tso Yee; Byer, Robert L.

    1988-01-01

    Recently, interest in diode laser-pumped solid-state lasers has increased due to their advantages over flashlamp-pumped solid-state lasers. A historical overview is presented of semiconductor diode-pumped solid-state lasers beginning with work in the early 1960s and continuing through recent work on wavelength extension of these devices by laser operation on new transitions. Modeling of these devices by rate equations to obtain expressions for threshold, slope efficiency, and figures of merit is also given.

  12. Diode pumped Nd:YAG laser development

    NASA Technical Reports Server (NTRS)

    Reno, C. W.; Herzog, D. G.

    1976-01-01

    A low power Nd:YAG laser was constructed which employs GaAs injection lasers as a pump source. Power outputs of 125 mW TEM CW with the rod at 250 K and the pump at 180 K were achieved for 45 W input power to the pump source. Operation of the laser, with array and laser at a common heat sink temperature of 250 K, was inhibited by difficulties in constructing long-life GaAs LOC laser arrays. Tests verified pumping with output power of 20 to 30 mW with rod and pump at 250 K. Although life tests with single LOC GaAs diodes were somewhat encouraging (with single diodes operating as long as 9000 hours without degradation), failures of single diodes in arrays continue to occur, and 50 percent power is lost in a few hundred hours at 1 percent duty factor. Because of the large recent advances in the state of the art of CW room temperature AlGaAs diodes, their demonstrated lifetimes of greater than 5,000 hours, and their inherent advantages for this task, it is recommended that these sources be used for further CW YAG injection laser pumping work.

  13. Design of diode laser systems for solid state laser pumping

    NASA Astrophysics Data System (ADS)

    Michel, D.; Luethy, Willy A.; Weber, Heinz P.

    2003-11-01

    In contrast to flashlamps the emission of single stripe laser diodes is highly directional and can be focused rather easily to small spots, which gives access to very high pump intensities. Numerical arrangements are possible for transferring the pump radiation to the solid state laser media. In this paper the most important concepts of diode laser systems for pumping solid state lasers are summarized and described. Thereby the aim is to find the most efficient and powerful method for endpumping a Yb3+-double clad fiber.

  14. Environmental testing of a diode-laser-pumped Nd:YAG laser and a set of diode-laser-arrays

    NASA Technical Reports Server (NTRS)

    Hemmati, H.; Lesh, J. R.

    1989-01-01

    Results of the environmental test of a compact, rigid and lightweight diode-laser-pumped Nd:YAG laser module are discussed. All optical elements are bonded onto the module using space applicable epoxy, and two 200 mW diode laser arrays for pump sources are used to achieve 126 mW of CW output with about 7 percent electrical-to-optical conversion efficiency. This laser assembly and a set of 20 semiconductor diode laser arrays were environmentally tested by being subjected to vibrational and thermal conditions similar to those experienced during launch of the Space Shuttle, and both performed well. Nevertheless, some damage to the laser front facet in diode lasers was observed. Significant degradation was observed only on lasers which performed poorly in the life test. Improvements in the reliability of the Nd:YAG laser are suggested.

  15. Diode pumped alkali vapor fiber laser

    DOEpatents

    Payne, Stephen A.; Beach, Raymond J.; Dawson, Jay W.; Krupke, William F.

    2007-10-23

    A method and apparatus is provided for producing near-diffraction-limited laser light, or amplifying near-diffraction-limited light, in diode pumped alkali vapor photonic-band-gap fiber lasers or amplifiers. Laser light is both substantially generated and propagated in an alkali gas instead of a solid, allowing the nonlinear and damage limitations of conventional solid core fibers to be circumvented. Alkali vapor is introduced into the center hole of a photonic-band-gap fiber, which can then be pumped with light from a pump laser and operated as an oscillator with a seed beam, or can be configured as an amplifier.

  16. Diode pumped alkali vapor fiber laser

    DOEpatents

    Payne, Stephen A.; Beach, Raymond J.; Dawson, Jay W.; Krupke, William F.

    2006-07-26

    A method and apparatus is provided for producing near-diffraction-limited laser light, or amplifying near-diffraction-limited light, in diode pumped alkali vapor photonic-band-gap fiber lasers or amplifiers. Laser light is both substantially generated and propagated in an alkali gas instead of a solid, allowing the nonlinear and damage limitations of conventional solid core fibers to be circumvented. Alkali vapor is introduced into the center hole of a photonic-band-gap fiber, which can then be pumped with light from a pump laser and operated as an oscillator with a seed beam, or can be configured as an amplifier.

  17. Diode laser prostatectomy (VLAP): initial canine evaluation

    NASA Astrophysics Data System (ADS)

    Kopchok, George E.; Verbin, Chris; Ayres, Bruce; Peng, Shi-Kaung; White, Rodney A.

    1995-05-01

    This study evaluated the acute and chronic effects of diode laser (960 nm) prostatectomy using a Prolase II fiber in a canine model (n equals 5). The laser fiber consists of a 1000 um quartz fiber which reflects a cone of laser energy, at 45 degree(s) to the axis of the fiber, into the prostatic urethra (Visual Laser Ablation of Prostate). Perineal access was used to guide a 15.5 Fr cystoscope to the level of the prostate. Under visual guidance and continual saline irrigation, 60 watts of laser power was delivered for 60 seconds at 3, 9, and 12 o'clock and 30 seconds at the 6 o'clock (posterior) positions for a total energy fluence of 12,600 J. One prostate received an additional 60 second exposure at 3 and 9 o'clock for a total fluence of 19,800 J. The prostates were evaluated at one day (n equals 1) and 8 weeks (n equals 4). The histopathology of laser effects at one day show areas of necrosis with loss of glandular structures and stromal edema. Surrounding this area was a zone of degenerative glandular structures extending up to 17.5 mm (cross sectional diameter). The histopathology of the 8 week laser treated animals demonstrated dilated prostatic urethras with maximum cross- sectional diameter of 23.4 mm (mean equals 18.5 +/- 3.9 mm). This study demonstrates the effectiveness of diode laser energy for prostatic tissue coagulation and eventual sloughing. The results also demonstrate the safety of diode laser energy, with similar tissue response as seen with Nd:YAG laser, for laser prostatectomy.

  18. Noninvasive blood glucose monitoring with laser diode

    NASA Astrophysics Data System (ADS)

    Zhang, Xiqin; Chen, Jianhong; Ooi, Ean Tat; Yeo, Joon Hock

    2006-02-01

    The non-invasive measurement of blood sugar level was studied by use of near infrared laser diodes. The in vitro and in vivo experiments were carried out using six laser diodes having wavelengths range from 1550 nm to 1750nm. Several volunteers were tested for OGTT (Oral Glucose Tolerance Test) experiment. We took blood from a fingertip and measured its concentration with a glucose meter while taking signal voltage from laser diodes system. The data of signal voltage were processed to do calibration and prediction; in this paper PLS (Partial Least Square) method was used to do modeling. For in vitro experiment, good linear relationship between predicted glucose concentration and real glucose concentration was obtained. For in vivo experiments, we got the blood sugar level distributions in Clarke error grid that is a reference for doctors to do diagnosis and treatment. In the Clarke error grid, 75% of all data was in area A and 25 % was in area B. From the in vitro and in vivo results we know that multiple laser diodes are suitable for non-invasive blood glucose monitoring.

  19. Advances in laser diodes for pyrotechnic applications

    NASA Technical Reports Server (NTRS)

    Craig, Richard R.

    1993-01-01

    Background information concerning the use of laser diodes in pyrotechnic applications is provided in viewgraph form. The following topics are discussed: damage limits, temperature stability, fiber coupling issues, and small (100 micron) and large (400 micron) fiber results. The discussions concerning fiber results concentrate on the areas of package geometry and electro-optical properties.

  20. Diode Laser Excision of Oral Benign Lesions

    PubMed Central

    Mathur, Ena; Sareen, Mohit; Dhaka, Payal; Baghla, Pallavi

    2015-01-01

    Introduction: Lasers have made tremendous progress in the field of dentistry and have turned out to be crucial in oral surgery as collateral approach for soft tissue surgery. This rapid progress can be attributed to the fact that lasers allow efficient execution of soft tissue procedures with excellent hemostasis and field visibility. When matched to scalpel, electrocautery or high frequency devices, lasers offer maximum postoperative patient comfort. Methods: Four patients agreed to undergo surgical removal of benign lesions of the oral cavity. 810 nm diode lasers were used in continuous wave mode for excisional biopsy. The specimens were sent for histopathological examination and patients were assessed on intraoperative and postoperative complications. Results: Diode laser surgery was rapid, bloodless and well accepted by patients and led to complete resolution of the lesions. The excised specimen proved adequate for histopathological examination. Hemostasis was achieved immediately after the procedure with minimal postoperative problems, discomfort and scarring. Conclusion: We conclude that diode lasers are rapidly becoming the standard of care in contemporary dental practice and can be employed in procedures requiring excisional biopsy of oral soft tissue lesions with minimal problems in histopathological diagnosis. PMID:26464781

  1. GaAs laser diode pumped Nd:YAG laser

    NASA Technical Reports Server (NTRS)

    Conant, L. C.; Reno, C. W.

    1974-01-01

    A 1.5-mm by 3-cm neodymium-ion doped YAG laser rod has been side pumped using a GaAs laser diode array tuned to the 8680-A absorption line, achieving a multimode average output power of 120 mW for a total input power of 20 W to the final-stage laser diode drivers. The pumped arrangement was designed to take advantage of the high brightness of a conventional GaAs array as a linear source by introducing the pump light through a slit into a close-wrapped gold coated pump cavity. This cavity forms an integrating chamber for the pump light.

  2. Four channel Laser Firing Unit using laser diodes

    NASA Technical Reports Server (NTRS)

    Rosner, David, Sr.; Spomer, Edwin, Sr.

    1994-01-01

    This paper describes the accomplishments and status of PS/EDD's (Pacific Scientific/Energy Dynamics Division) internal research and development effort to prototype and demonstrate a practical four channel laser firing unit (LFU) that uses laser diodes to initiate pyrotechnic events. The LFU individually initiates four ordnance devices using the energy from four diode lasers carried over the fiber optics. The LFU demonstrates end-to-end optical built in test (BIT) capabilities. Both Single Fiber Reflective BIT and Dual Fiber Reflective BIT approaches are discussed and reflection loss data is presented. This paper includes detailed discussions of the advantages and disadvantages of both BIT approaches, all-fire and no-fire levels, and BIT detection levels. The following topics are also addressed: electronic control and BIT circuits, fiber optic sizing and distribution, and an electromechanical shutter type safe/arm device. This paper shows the viability of laser diode initiation systems and single fiber BIT for typing military applications.

  3. Design of laser diode stable output system

    NASA Astrophysics Data System (ADS)

    Liu, Bo; Cao, Rui-ming

    2008-03-01

    High-stability output's system of laser diode is introduced in this paper. The system which is based on the MCU of MSP430 has been designed light power feedback loop and coller of TEC. It includes stable current, protecting circuit, light power feedback loop, temperature controlling, power display and so on. It is also able to control and show the power at the real time. The power could be set by botton too. The software of slow start up, slow close and the protecting relay are adopted by MCU. DRV592 is introduced as PWM driver to control the current of TEC. The duty cycle is generate by MCU. In order to control temperature, it is changed to influence the current of TEC. The power that is sampled by photodiode which is integrated in the laser diode is controlled by the micro-processing. The laser is monitored by voltage control circuit and current control circuit at the real time.

  4. Topics in Laser Spectroscopy: A semiconductor diode laser spectrometer for laser spectrochemistry

    NASA Astrophysics Data System (ADS)

    Lawrenz, J.; Niemax, K.

    The construction and the use of a single mode semiconductor diode laser spectrometer which can be tuned electronically controlled by temperature as well as by current is presented. The spectroscopic properties of this spectrometer including commercial semiconductor diode lasers of the AlGaAs/GaAs type operating in the wavelength range 735-860 nm are discussed. Examples of the application of diode laser spectrometers in laser spectrochemistry are given.

  5. Radiation Degradation Mechanisms in Laser Diodes

    NASA Technical Reports Server (NTRS)

    Johston, A. H.; Miyahira, T. F.

    2004-01-01

    Degradation mechanisms are investigated for laser diodes fabricated with different materials and wavelengths between 660 and 1550 nm. A new approach is developed that evaluates degradation below the laser threshold to determine the radiation-induced recombination density. This allows mechanisms at high injection, such as Auger recombination, to be separated from low-injection damage. New results show that AlGaInP lasers in the visible region are nearly an order of magnitude more resistant to radiation than devices fabricated with AlGaAs or AlGaAsP at longer wavelengths.

  6. Diode laser-pumped solid-state lasers

    NASA Technical Reports Server (NTRS)

    Byer, Robert L.

    1988-01-01

    An evaluation is made of the consequences for solid-state lasers of novel diode laser-pumping technology. Diode laser-pumped neodymium lasers have operated at an electrical-to-optical efficiency of 10 percent in a single spatial mode, with linewidths of less than 10 kHz, and with a spectral power brightness sufficiently great to allow frequency extension by harmonic generation in nonlinear crystals; this has yielded green and blue sources of coherent radiation. Q-switched operation with kW peak powers and mode-locked operation with 10-picosec pulse widths have also been demonstrated. All-solid-state lasers at prices comparable to those of current flash-lamp-pumped laser systems are foreseen, as are power levels exceeding 1 kW, for coherent radar, global satellite sensing, and micromachining.

  7. Diode pumped solid-state laser oscillators for spectroscopic applications

    NASA Technical Reports Server (NTRS)

    Byer, R. L.; Basu, S.; Fan, T. Y.; Kozlovsky, W. J.; Nabors, C. D.; Nilsson, A.; Huber, G.

    1987-01-01

    The rapid improvement in diode laser pump sources has led to the recent progress in diode laser pumped solid state lasers. To date, electrical efficiencies of greater than 10 percent were demonstrated. As diode laser costs decrease with increased production volume, diode laser and diode laser array pumped solid state lasers will replace the traditional flashlamp pumped Nd:YAG laser sources. The use of laser diode array pumping of slab geometry lasers will allow efficient, high peak and average power solid state laser sources to be developed. Perhaps the greatest impact of diode laser pumped solid state lasers will be in spectroscopic applications of miniature, monolithic devices. Single-stripe diode-pumped operation of a continuous-wave 946 nm Nd:YAG laser with less than 10 m/w threshold was demonstrated. A slope efficiency of 16 percent near threshold was shown with a projected slope efficiency well above a threshold of 34 percent based on results under Rhodamine 6G dye-laser pumping. Nonlinear crystals for second-harmonic generation of this source were evaluated. The KNbO3 and periodically poled LiNbO3 appear to be the most promising.

  8. Visible fiber lasers excited by GaN laser diodes

    NASA Astrophysics Data System (ADS)

    Fujimoto, Yasushi; Nakanishi, Jun; Yamada, Tsuyoshi; Ishii, Osamu; Yamazaki, Masaaki

    2013-07-01

    This paper describes and discusses visible fiber lasers that are excited by GaN laser diodes. One of the attractive points of visible light is that the human eye is sensitive to it between 400 and 700 nm, and therefore we can see applications in display technology. Of course, many other applications exist. First, we briefly review previously developed visible lasers in the gas, liquid, and solid-state phases and describe the history of primary solid-state visible laser research by focusing on rare-earth doped fluoride media, including glasses and crystals, to clarify the differences and the merits of primary solid-state visible lasers. We also demonstrate over 1 W operation of a Pr:WPFG fiber laser due to high-power GaN laser diodes and low-loss optical fibers (0.1 dB/m) made by waterproof fluoride glasses. This new optical fiber glass is based on an AlF3 system fluoride glass, and its waterproof property is much better than the well known fluoride glass of ZBLAN. The configuration of primary visible fiber lasers promises highly efficient, cost-effective, and simple laser systems and will realize visible lasers with photon beam quality and quantity, such as high-power CW or tunable laser systems, compact ultraviolet lasers, and low-cost ultra-short pulse laser systems. We believe that primary visible fiber lasers, especially those excited by GaN laser diodes, will be effective tools for creating the next generation of research and light sources.

  9. Integrated software package for laser diodes characterization

    NASA Astrophysics Data System (ADS)

    Sporea, Dan G.; Sporea, Radu A.

    2003-10-01

    The characteristics of laser diodes (wavelength of the emitted radiation, output optical power, embedded photodiode photocurrent, threshold current, serial resistance, external quantum efficiency) are strongly influenced by their driving circumstances (forward current, case temperature). In order to handle such a complex investigation in an efficient and objective manner, the operation of several instruments (a laser diode driver, a temperature controller, a wavelength meter, a power meter, and a laser beam analyzer) is synchronously controlled by a PC, through serial and GPIB communication. For each equipment, instruments drivers were designed using the industry standards graphical programming environment - LabVIEW from National Instruments. All the developed virtual instruments operate under the supervision of a managing virtual instrument, which sets the driving parameters for each unit under test. The manager virtual instrument scans as appropriate the driving current and case temperature values for the selected laser diode. The software enables data saving in Excel compatible files. In this way, sets of curves can be produced according to the testing cycle needs.

  10. Proton displacement damage in light-emitting and laser diodes

    NASA Technical Reports Server (NTRS)

    Johnston, A. H.

    2000-01-01

    The effects of proton displacement damage on light-emitting diodes and laser diodes are discussed, comparing the radiation sensitivity of current technology devices with older devices for which data exists in the literature.

  11. Diode laser welding of aluminum to steel

    SciTech Connect

    Santo, Loredana; Quadrini, Fabrizio; Trovalusci, Federica

    2011-05-04

    Laser welding of dissimilar materials was carried out by using a high power diode laser to join aluminum to steel in a butt-joint configuration. During testing, the laser scan rate was changed as well as the laser power: at low values of fluence (i.e. the ratio between laser power and scan rate), poor joining was observed; instead at high values of fluence, an excess in the material melting affected the joint integrity. Between these limiting values, a good aesthetics was obtained; further investigations were carried out by means of tensile tests and SEM analyses. Unfortunately, a brittle behavior was observed for all the joints and a maximum rupture stress about 40 MPa was measured. Apart from the formation of intermeltallic phases, poor mechanical performances also depended on the chosen joining configuration, particularly because of the thickness reduction of the seam in comparison with the base material.

  12. Diode laser absorption sensors for combustion control

    NASA Astrophysics Data System (ADS)

    Xin, Zhou

    Combustion is the most widely used energy conversion technique in the world. Diode-laser absorption sensors offer significant opportunities and advantages for in situ measurements of multiple combustion parameters such as temperature and species concentration due to their high sensitivity, high spectral resolution, fast time response, robustness and non-intrusive character. The overall objective of this thesis is to design and develop time-resolved and real-time tunable diode laser sensors with the potential for combustion control. A crucial element in the design of a tunable-diode-laser optical-absorption-based sensor is the selection of optimum transitions. The strategy and spectroscopic criteria for selecting optimum wavelength regions and absorption line combinations are developed. The development of this design-rule approach establishes a new paradigm to optimize tunable diode laser sensors for target applications. The water vapor spectrum in the 1-2 mum near-infrared region is systematically analyzed to find the best absorption transition pairs for sensitive measurement of temperature in the target combustion environment using a single tunable diode laser. Two sensors are developed in this work. The first sensor is a 1.8 mum, single-laser temperature sensor based on direct absorption scans. Successful time-resolved measurements in a variety of laboratory and practical devices are presented and used to identify potential improvements, and design rules for a second-generation sensor are developed based on the lessons learned. The second generation sensor is a 1.4 mum, single-laser temperature sensor using water vapor absorption detected by wavelength-modulation spectroscopy (WMS), which facilitates rapid data analysis and a 2 kHz real-time data rate in the combustion experiments reported here. Demonstration experiments in a heated cell and a forced Hencken burner confirm the sensitivity and accuracy of the sensors. The first application of TDL thermometry to a

  13. A new diode laser acupuncture therapy apparatus

    NASA Astrophysics Data System (ADS)

    Li, Chengwei; Huang, Zhen; Li, Dongyu; Zhang, Xiaoyuan

    2006-06-01

    Since the first laser-needles acupuncture apparatus was introduced in therapy, this kind of apparatus has been well used in laser biomedicine as its non-invasive, pain- free, non-bacterium, and safetool. The laser acupuncture apparatus in this paper is based on single-chip microcomputer and associated by semiconductor laser technology. The function like traditional moxibustion including reinforcing and reducing is implemented by applying chaos method to control the duty cycle of moxibustion signal, and the traditional lifting and thrusting of acupuncture is implemented by changing power output of the diode laser. The radiator element of diode laser is made and the drive circuit is designed. And chaos mathematic model is used to produce deterministic class stochastic signal to avoid the body adaptability. This function covers the shortages of continuous irradiation or that of simple disciplinary stimulate signal, which is controlled by some simple electronic circuit and become easily adjusted by human body. The realization of reinforcing and reducing of moxibustion is technological innovation in traditional acupuncture coming true in engineering.

  14. High power diode lasers for solid-state laser pumps

    NASA Astrophysics Data System (ADS)

    Linden, Kurt J.; McDonnell, Patrick N.

    1994-02-01

    The development and commercial application of high power diode laser arrays for use as solid-state laser pumps is described. Such solid-state laser pumps are significantly more efficient and reliable than conventional flash-lamps. This paper describes the design and fabrication of diode lasers emitting in the 780 - 900 nm spectral region, and discusses their performance and reliability. Typical measured performance parameters include electrical-to-optical power conversion efficiencies of 50 percent, narrow-band spectral emission of 2 to 3 nm FWHM, pulsed output power levels of 50 watts/bar with reliability values of over 2 billion shots to date (tests to be terminated after 10 billion shots), and reliable operation to pulse lengths of 1 ms. Pulse lengths up to 5 ms have been demonstrated at derated power levels, and CW performance at various power levels has been evaluated in a 'bar-in-groove' laser package. These high-power 1-cm stacked-bar arrays are now being manufactured for OEM use. Individual diode laser bars, ready for package-mounting by OEM customers, are being sold as commodity items. Commercial and medical applications of these laser arrays include solid-state laser pumping for metal-working, cutting, industrial measurement and control, ranging, wind-shear/atmospheric turbulence detection, X-ray generation, materials surface cleaning, microsurgery, ophthalmology, dermatology, and dental procedures.

  15. High power diode lasers for solid-state laser pumps

    NASA Technical Reports Server (NTRS)

    Linden, Kurt J.; Mcdonnell, Patrick N.

    1994-01-01

    The development and commercial application of high power diode laser arrays for use as solid-state laser pumps is described. Such solid-state laser pumps are significantly more efficient and reliable than conventional flash-lamps. This paper describes the design and fabrication of diode lasers emitting in the 780 - 900 nm spectral region, and discusses their performance and reliability. Typical measured performance parameters include electrical-to-optical power conversion efficiencies of 50 percent, narrow-band spectral emission of 2 to 3 nm FWHM, pulsed output power levels of 50 watts/bar with reliability values of over 2 billion shots to date (tests to be terminated after 10 billion shots), and reliable operation to pulse lengths of 1 ms. Pulse lengths up to 5 ms have been demonstrated at derated power levels, and CW performance at various power levels has been evaluated in a 'bar-in-groove' laser package. These high-power 1-cm stacked-bar arrays are now being manufactured for OEM use. Individual diode laser bars, ready for package-mounting by OEM customers, are being sold as commodity items. Commercial and medical applications of these laser arrays include solid-state laser pumping for metal-working, cutting, industrial measurement and control, ranging, wind-shear/atmospheric turbulence detection, X-ray generation, materials surface cleaning, microsurgery, ophthalmology, dermatology, and dental procedures.

  16. Novel developments in laser diode Raman spectroscopy

    NASA Astrophysics Data System (ADS)

    Claps, Ricardo Javier

    2000-11-01

    This thesis presents the last developments of a laser diode Raman spectrometer for gases, gas flows and vapors, at medium-low pressures. Results are shown for atmospheric gases under STP conditions, and also gas flows from nozzles in subsonic-sonic regimes. The system is unique in that it uses a high power laser diode passively locked by an external grating cavity in Littman/Metcalf configuration, with side-band modes suppressed by 1:10-5, and a reduced bandwidth of <500MHz. The use of Rb vapor cells as notch filters with unprecedented narrow bandwidth (<7 cm-1), allow to collect Stokes and a-Stokes rotational Raman spectra simultaneously. The spectrometer is used to perform studies of thermodynamic equilibrium of gas flows; further studies of samples seeded in the flow (alkali- halides) are discussed, together with potential applications for environmental and industrial monitoring.

  17. Outlook for diode lasers in medicine

    NASA Astrophysics Data System (ADS)

    Arons, Irving J.

    1994-07-01

    From their use in compact disc players and telecommunications to supermarket scanners, semi-conductor diode lasers now play an ever important role in medicine. Beginning in ophthalmology, as replacements for ion photocoagulator lasers, and used for several years outside of the United States for biostimulation of aching muscles and to treat chronic ulcers and wounds, high-powered diode systems are now finding their way into surgery and, in the future, will be used to activate photoactive dyes in the photodynamic therapy treatment of cancers, and perhaps to weld tissue to replace sutures. In this presentation, we attempt to cover the above applications as well as some newer ones, discussing the companies involved, the systems in use or under development, and some exciting new developments about to unfold.

  18. Prototype laser-diode-pumped solid state laser transmitters

    NASA Technical Reports Server (NTRS)

    Kane, Thomas J.; Cheng, Emily A. P.; Wallace, Richard W.

    1989-01-01

    Monolithic, diode-pumped Nd:YAG ring lasers can provide diffraction-limited, single-frequency, narrow-linewidth, tunable output which is adequate for use as a local oscillator in a coherent communication system. A laser was built which had a linewidth of about 2 kHz, a power of 5 milliwatts, and which was tunable over a range of 30 MHz in a few microseconds. This laser was phase-locked to a second, similar laser. This demonstrates that the powerful technique of heterodyne detection is possible with a diode-pumped laser used as the local oscillator. Laser diode pumping of monolithic Nd:YAG rings can lead to output powers of hundreds of milliwatts from a single laser. A laser was built with a single-mode output of 310 mW. Several lasers can be chained together to sum their power, while maintaining diffraction-limited, single frequency operation. This technique was demonstrated with two lasers, with a total output of 340 mW, and is expected to be practical for up to about ten lasers. Thus with lasers of 310 mW, output of up to 3 W is possible. The chaining technique, if properly engineered, results in redundancy. The technique of resonant external modulation and doubling is designed to efficiently convert the continuous wave, infrared output of our lasers into low duty-cycle pulsed green output. This technique was verified through both computer modeling and experimentation. Further work would be necessary to develop a deliverable system using this technique.

  19. Optical communication with semiconductor laser diode

    NASA Technical Reports Server (NTRS)

    Davidson, Frederic; Sun, X.

    1989-01-01

    This interim report describes the progress in the construction of a 220 Mbps Q=4 PPM optical communication system that uses a semiconductor laser as the optical transmitter and an avalanche photodiode (APD) as the photodetector. The transmitter electronics have been completed and contain both GaAs and ECL III IC's. The circuit was able to operate at a source binary data rate from 75 Mbps to 290 Mbps with pulse rise and fall times of 400 ps. The pulse shapes of the laser diode and the response from the APD/preamplifier module were also measured.

  20. Advancements in flowing diode pumped alkali lasers

    NASA Astrophysics Data System (ADS)

    Pitz, Greg A.; Stalnaker, Donald M.; Guild, Eric M.; Oliker, Benjamin Q.; Moran, Paul J.; Townsend, Steven W.; Hostutler, David A.

    2016-03-01

    Multiple variants of the Diode Pumped Alkali Laser (DPAL) have recently been demonstrated at the Air Force Research Laboratory (AFRL). Highlights of this ongoing research effort include: a) a 571W rubidium (Rb) based Master Oscillator Power Amplifier (MOPA) with a gain (2α) of 0.48 cm-1, b) a rubidium-cesium (Cs) Multi-Alkali Multi-Line (MAML) laser that simultaneously lases at both 795 nm and 895 nm, and c) a 1.5 kW resonantly pumped potassium (K) DPAL with a slope efficiency of 50%. The common factor among these experiments is the use of a flowing alkali test bed.

  1. Diode pumped alkali lasers (DPALs): an overview

    NASA Astrophysics Data System (ADS)

    Krupke, William F.

    2008-05-01

    The concept of power-scalable, high beam-quality diode pumped alkali lasers was introduced in 2003 [Krupke, US Patent No. 6,643,311; Opt. Letters, 28, 2336 (2003)]. Since then several laboratory DPAL devices have been reported on, confirming many of the spectroscopic, kinetic, and laser characteristics projected from literature data. This talk will present an overview of the DPAL concept, summarize key relevant properties of the cesium, rubidium, and potassium alkali vapor gain media so-far examined, outline power scaling considerations, and highlight results of published DPAL laboratory experiments.

  2. Space Qualification of Laser Diode Arrays

    NASA Technical Reports Server (NTRS)

    Troupaki, Elisavet; Kashem, Nasir B.; Allan, Graham R.; Vasilyev, Aleksey; Stephen, Mark

    2005-01-01

    Laser instruments have great potential in enabling a new generation of remote-sensing scientific instruments. NASA s desire to employ laser instruments aboard satellites, imposes stringent reliability requirements under severe conditions. As a result of these requirements, NASA has a research program to understand, quantify and reduce the risk of failure to these instruments when deployed on satellites. Most of NASA s proposed laser missions have base-lined diode-pumped Nd:YAG lasers that generally use quasi-constant wave (QCW), 808 nm Laser Diode Arrays (LDAs). Our group has an on-going test program to measure the performance of these LDAs when operated in conditions replicating launch and orbit. In this paper, we report on the results of tests designed to measure the effect of vibration loads simulating launch into space and the radiation environment encountered on orbit. Our primary objective is to quantify the performance of the LDAs in conditions replicating those of a satellite instrument, determine their limitations and strengths which will enable better and more robust designs. To this end we have developed a systematic testing strategy to quantify the effect of environmental stresses on the optical and electrical properties of the LDA.

  3. Laser welding of polymers using high-power diode lasers

    NASA Astrophysics Data System (ADS)

    Bachmann, Friedrich G.; Russek, Ulrich A.

    2002-06-01

    Laser welding of polymers using high power diode lasers offers specific process advantages over conventional technologies, such as short process times while providing optically and qualitatively valuable weld seams, contactless yielding of the joining energy, absence of process induced vibrations, imposing minimal thermal stress and avoiding particle generation. Furthermore, this method exhibits high integration capabilities and automatization potential. Moreover, because of the current favorable cost development within the high power diode laser market laser welding of polymers has become more and more an industrially accepted joining method. This novel technology permits both, reliable high quality joining of mechanically and electronically highly sensitive micro components and hermetic sealing of macro components. There are different welding strategies available, which are adaptable to the current application. Within the frame of this discourse scientific and also application oriented result concerning laser transmission welding of polymers using preferably diode lasers are presented. Besides the sue laser system the fundamental process strategies as well as decisive process parameters are illustrated. The importance of optical, thermal and mechanical properties is discussed. Applications at real technical components will be presented, demonstrating the industrial implementation capability and the advantages of a novel technology.

  4. Laser welding of polymers using high-power diode lasers

    NASA Astrophysics Data System (ADS)

    Bachmann, Friedrich G.; Russek, Ulrich A.

    2003-09-01

    Laser welding of polymers using high power diode lasers offers specific process advantages over conventional technologies, such as short process times while providing optically and qualitatively valuable weld seams, contactless yielding of the joining energy, absence of process induced vibrations, imposing minimal thermal stress and avoiding particle generation. Furthermore this method exhibits high integration capabilities and automatization potential. Moreover, because of the current favorable cost development within the high power diode laser market laser welding of polymers has become more and more an industrially accepted joining method. This novel technology permits both, reliable high quality joining of mechanically and electronically highly sensitive micro components and hermetic sealing of macro components. There are different welding strategies available, which are adaptable to the current application. Within the frame of this discourse scientific and also application oriented results concerning laser transmission welding of polymers using preferably diode lasers are presented. Besides the used laser systems the fundamental process strategies as well as decisive process parameters are illustrated. The importance of optical, thermal and mechanical properties is discussed. Applications at real technical components will be presented, demonstrating the industrial implementation capability and the advantages of a novel technology.

  5. Electrostatic Discharge (ESD) Protection for a Laser Diode Ignited Actuator

    SciTech Connect

    SALAS, FREDERICK J.; SANCHEZ, DANIEL H.; WEINLEIN, JOHN HARVEY

    2003-06-01

    The use of laser diodes in devices to ignite pyrotechnics provides unique new capabilities including the elimination of electrostatic discharge (ESD) pulses entering the device. The Faraday cage formed by the construction of these devices removes the concern of inadvertent ignition of the energetic material. However, the laser diode itself can be damaged by ESD pulses, therefore, to enhance reliability, some protection of the laser diode is necessary. The development of the MC4612 Optical Actuator has included a circuit to protect the laser diode from ESD pulses including the ''Fisher'' severe human body ESD model. The MC4612 uses a laser diode and is designed to replace existing hot-wire actuators. Optical energy from a laser diode, instead of electrical energy, is used to ignite the pyrotechnic. The protection circuit is described along with a discussion of how the circuit design addresses and circumvents the historic 1Amp/1Watt requirement that has been applicable to hot-wire devices.

  6. Low-cost laser diode array

    DOEpatents

    Freitas, Barry L.; Skidmore, Jay A.

    1999-01-01

    A substrate is used to fabricate a low-cost laser diode array. A substrate is machined from an electrically insulative material that is thermally conductive, or two substrates can be bonded together in which the top substrate is electrically as well as thermally conductive. The substrate thickness is slightly longer than the cavity length, and the width of the groove is wide enough to contain a bar and spring (which secures the laser bar firmly along one face of the groove). The spring also provides electrical continuity from the backside of the bar to the adjacent metalization layer on the laser bar substrate. Arrays containing one or more bars can be formed by creating many grooves at various spacings. Along the groove, many bars can be adjoined at the edges to provide parallel electrical conduction. This architecture allows precise and predictable registration of an array of laser bars to a self-aligned microlens array at low cost.

  7. Low-cost laser diode array

    DOEpatents

    Freitas, B.L.; Skidmore, J.A.

    1999-06-01

    A substrate is used to fabricate a low-cost laser diode array. A substrate is machined from an electrically insulative material that is thermally conductive, or two substrates can be bonded together in which the top substrate is electrically as well as thermally conductive. The substrate thickness is slightly longer than the cavity length, and the width of the groove is wide enough to contain a bar and spring (which secures the laser bar firmly along one face of the groove). The spring also provides electrical continuity from the backside of the bar to the adjacent metalization layer on the laser bar substrate. Arrays containing one or more bars can be formed by creating many grooves at various spacings. Along the groove, many bars can be adjoined at the edges to provide parallel electrical conduction. This architecture allows precise and predictable registration of an array of laser bars to a self-aligned microlens array at low cost. 19 figs.

  8. Role of diode lasers in metrology

    NASA Astrophysics Data System (ADS)

    Muthukrishnan, Kris

    1995-01-01

    The field of noncontact metrology is maturing as the video camera based and the laser probe based measurements are finding wide acceptance in the fields of semiconductor, micro electronics, disk drive, biomedical, chemical and aerospace industries. Some manufactures of conventional touch-probe based CMMs (Coordinated Measuring Machines) have started integrating video cameras and laser probes to compliment the measurements made by the touch-probe. The delicate nature of the parts and the extremely small feature sizes have fuelled the growing need for the multisensor technology to be incorporated into a single coordinate measuring machine. The laser probes compliment the video based metrology systems in providing the dynamic Z-height capabilities due to their faster data rate and increased resolution and accuracy. This paper highlights the pros and cons of different diode laser based sensors, drawn from the experience of applying them for measurements in different fields.

  9. Diode Laser Measurements of Concentration and Temperature in Microgravity Combustion

    NASA Technical Reports Server (NTRS)

    Silver, Joel A.; Kane, Daniel J.

    1999-01-01

    Diode laser absorption spectroscopy provides a direct method of determinating species concentration and local gas temperature in combustion flames. Under microgravity conditions, diode lasers are particularly suitable, given their compact size, low mass and low power requirements. The development of diode laser-based sensors for gas detection in microgravity is presented, detailing measurements of molecular oxygen. Current progress of this work and future application possibilities for these methods on the International Space Station are discussed.

  10. Diode laser potential in laser cleaning of stones

    NASA Astrophysics Data System (ADS)

    Salimbeni, Renzo; Pini, Roberto; Siano, Salvatore; Bachmann, Friedrich G.; Meyer, Frank

    2001-10-01

    In this work we investigated for the first time the laser cleaning process of encrusted stones by employing a high power diode laser system. The test have been carried out using a Rofin-Sinar mod. DL025S emitting up to 2.5 kW CW power to clean various samples representing natural encrustation by pollution exposition and graffiti, typically encountered on historical monuments and buildings in urban environment.

  11. Diode Laser for Laryngeal Surgery: a Systematic Review

    PubMed Central

    Arroyo, Helena Hotz; Neri, Larissa; Fussuma, Carina Yuri; Imamura, Rui

    2016-01-01

    Introduction The diode laser has been frequently used in the management of laryngeal disorders. The portability and functional diversity of this tool make it a reasonable alternative to conventional lasers. However, whether diode laser has been applied in transoral laser microsurgery, the ideal parameters, outcomes, and adverse effects remain unclear. Objective The main objective of this systematic review is to provide a reliable evaluation of the use of diode laser in laryngeal diseases, trying to clarify its ideal parameters in the larynx, as well as its outcomes and complications. Data Synthesis We included eleven studies in the final analysis. From the included articles, we collected data on patient and lesion characteristics, treatment (diode laser's parameters used in surgery), and outcomes related to the laser surgery performed. Only two studies were prospective and there were no randomized controlled trials. Most of the evidence suggests that the diode laser can be a useful tool for treatment of different pathologies in the larynx. In this sense, the parameters must be set depending on the goal (vaporization, section, or coagulation) and the clinical problem. Conclusion: The literature lacks studies on the ideal parameters of the diode laser in laryngeal surgery. The available data indicate that diode laser is a useful tool that should be considered in laryngeal surgeries. Thus, large, well-designed studies correlated with diode compared with other lasers are needed to better estimate its effects. PMID:27096024

  12. Quasi-CW Laser Diode Bar Life Tests

    NASA Technical Reports Server (NTRS)

    Stephen, Mark A.; Krainak, Michael A.; Dallas, Joseph L.

    1997-01-01

    NASA's Goddard Space Flight Center is developing technology for satellite-based, high peak power, LIDAR transmitters requiring 3-5 years of reliable operation. Semi-conductor laser diodes provide high efficiency pumping of solid state lasers with the promise of long-lived, reliable operation. 100-watt quasi- CW laser diode bars have been baselined for the next generation laser altimeters. Multi-billion shot lifetimes are required. The authors have monitored the performance of several diodes for billions of shots and investigated operational modes for improving diode lifetime.

  13. Laboratory diode laser spectroscopy in molecular planetary astronomy

    NASA Technical Reports Server (NTRS)

    Jennings, D. E.

    1988-01-01

    Infrared spectroscopy of planetary atmospheres is performed at high spectral resolution comparable to that in the laboratory. This requires that laboratory spectroscopy use the highest resolution and the most accurate techniques. Tunable diode laser spectroscopy can supply many of the spectroscopic parameters needed by astronomers. In particular, line positions, line strengths, and collisional line widths are measured with diode lasers, and these are often among the best values available. Diode laser spectra are complimentary to lower resolution, broader-coverage Fourier transform spectra. Certain procedures must be adopted, however, when using diode lasers, for determining their output characteristics and for calibrating each spectrum against quality references.

  14. Spectroscopy with Comb-Referenced Diode Lasers

    NASA Astrophysics Data System (ADS)

    Cich, Matthew; Lopez, Gary V.; Johnson, Philip M.; Sears, Trevor J.; McRaven, Christopher P.

    2010-06-01

    Extended cavity diode lasers have been stabilized by locking to components of an erbium-doped fiber laser-based frequency comb with a 250 MHz comb spacing centered at 1.5μ m. We find the Allan variance of the diode laser frequency relative to the single comb component to which it is locked is of the order of a few Hz. For the system as a whole, the absolute frequency accuracy is approximately 1.5 parts in 1012. In order to characterize the system more completely, we have recorded saturation dip absorption spectra of several transitions in the ν_1 + ν_3 combination band of acetylene near 6530 cm-1. We find good agreement with published absolute frequency measurements for these transitions, which have been used as secondary frequency standards in the past. Aside from extremely precise saturation dip measurements such as these, comb-stabilized lasers should permit excellent measurements of Doppler-broadened lineshapes, both to compare with theory and for analytical applications. Progress along these lines will be reported at the meeting. Acknowledgments: T. J. Sears gratefully acknowledges support from a Brookhaven National Laboratory program development grant that enabled this work and also support for research at Brookhaven National Laboratory which was carried out under Contract No. DE-AC02-98CH10886 with the U.S. Department of Energy and supported by its Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences and Biosciences.

  15. Long-Lifetime Laser Materials For Effective Diode Pumping

    NASA Technical Reports Server (NTRS)

    Barnes, Norman P.

    1991-01-01

    Long quantum lifetimes reduce number of diodes required to pump. Pumping by laser diodes demonstrated with such common Nd laser materials as neodymium:yttrium aluminum garnet (Nd:YAG) and Nd:YLiF4, but such materials as Nd:LaF3, Nd:NaF.9YF3, and possibly Nd:YF3 more useful because of long lifetimes of their upper laser energy levels. Cost effectiveness primary advantage of solid-state laser materials having longer upper-laser-level lifetimes. Because cost of diodes outweighs cost of laser material by perhaps two orders of magnitude, cost reduced significantly.

  16. Diode Laser Application in Soft Tissue Oral Surgery

    PubMed Central

    Azma, Ehsan; Safavi, Nassimeh

    2013-01-01

    Introduction: Diode laser with wavelengths ranging from 810 to 980 nm in a continuous or pulsed mode was used as a possible instrument for soft tissue surgery in the oral cavity. Discussion: Diode laser is one of laser systems in which photons are produced by electric current with wavelengths of 810, 940 and 980nm. The application of diode laser in soft tissue oral surgery has been evaluated from a safety point of view, for facial pigmentation and vascular lesions and in oral surgery excision; for example frenectomy, epulis fissuratum and fibroma. The advantages of laser application are that it provides relatively bloodless surgical and post surgical courses with minimal swelling and scarring. We used diode laser for excisional biopsy of pyogenic granuloma and gingival pigmentation. Conclusion: The diode laser can be used as a modality for oral soft tissue surgery PMID:25606331

  17. Underwater Chaotic Lidar using Blue Laser Diodes

    NASA Astrophysics Data System (ADS)

    Rumbaugh, Luke K.

    The thesis proposes and explores an underwater lidar system architecture based on chaotic modulation of recently introduced, commercially available, low cost blue laser diodes. This approach is experimentally shown to allow accurate underwater impulse response measurements while eliminating the need for several major components typically found in high-performance underwater lidar systems. The proposed approach is to: 1. Generate wideband, noise-like intensity modulation signals using optical chaotic modulation of blue-green laser diodes, and then 2. Use this signal source to develop an underwater chaotic lidar system that uses no electrical signal generator, no electro-optic modulator, no optical frequency doubler, and no large-aperture photodetector. The outcome of this thesis is the demonstration of a new underwater lidar system architecture that could allow high resolution ranging, imaging, and water profiling measurements in turbid water, at a reduced size, weight, power and cost relative to state-of-the-art high-performance underwater lidar sensors. This work also makes contributions to the state of the art in optics, nonlinear dynamics, and underwater sensing by demonstrating for the first time: 1. Wideband noise-like intensity modulation of a blue laser diode using no electrical signal generator or electro-optic modulator. Optical chaotic modulation of a 462 nm blue InGaN laser diode by self-feedback is explored for the first time. The usefulness of the signal to chaotic lidar is evaluated in terms of bandwidth, modulation depth, and autocorrelation peak-to-sidelobe-ratio (PSLR) using both computer and laboratory experiments. In laboratory experiments, the optical feedback technique is shown to be effective in generating wideband, noise-like chaotic signals with strong modulation depth when the diode is operated in an external-cavity dominated state. The modulation signal strength is shown to be limited by the onset of lasing within the diode's internal

  18. Flight demonstration of laser diode initiated ordnance

    NASA Technical Reports Server (NTRS)

    Boucher, Craig J.; Schulze, Norman R.

    1995-01-01

    A program has been initiated by NASA Headquarters to validate laser initiated ordnance in flight applications. The primary program goal is to bring together a team of government and industry members to develop a laser initiated ordnance system having the test and analysis pedigree to be flown on launch vehicles. The culmination of this effort was a flight of the Pegasus launch vehicle which had two fin rockets initiated by this laser system. In addition, a laser initiated ordnance squib was fired into a pressure bomb during thrusting flight. The complete ordnance system comprising a laser diode firing unit, fiber optic cable assembly, laser initiated detonator, and laser initiated squib was designed and built by The Ensign Bickford Company. The hardware was tested to the requirements of the Pegasus launch vehicle and integrated into the vehicle by The Ensign Bickford Company and the Orbital Sciences Corporation. Discussions include initial program concept, contract implementation, team member responsibilities, analysis results, vehicle integration, safing architecture, ordnance interfaces, mission timeline and telemetry data. A complete system description, summary of the analyses, the qualification test results, and the results of flight are included.

  19. Improved multipass optics for diode laser spectroscopy

    SciTech Connect

    Hu, T.A.; Chappell, E.L.; Munley, J.T.; Sharpe, S.W. )

    1993-12-01

    Feedback between optical elements can be a major source of noise when trying to attain high sensitivity in infrared absorption experiments. We find that a conventional White-cell optical arrangement introduces etaloning fringes that modulate the peak-to-peak amplitude of our signals by 1 part in 16 666, a fractional change of 6[times]10[sup [minus]5]. Although relatively small, this noise'' is systematic and adds coherently with averaging, obscuring interesting absorption features. An easily constructed multipass optical system suited for performing high-resolution infrared spectroscopy in molecular beams is described. The design is based on a variation of the White cell and has been optimized for use with lead salt diode lasers. One of the key components in the improved design is the addition of an oscillating mirror for spoiling optical feedback generated by laser scatter and/or poor mode coupling of the laser to the multipass optics.

  20. Using a Diode Laser for Laser-Induced Fluorescence

    NASA Astrophysics Data System (ADS)

    Tran, Yang; Whitten, J. E.

    2001-08-01

    The construction and use of a laser fluorimeter from a 635-nm red diode laser and an amplified photodiode detector are described. The low cost and monochromatic nature of diode lasers make them attractive as excitation sources for educational fluorescence experiments. Use of this type of fluorimeter is demonstrated by measuring fluorescence signals for various concentrations of Nile blue A dissolved in methanol; concentrations as low as 1 ppb are easily detected. The use of this instrument for monitoring the decomposition of a dye by an oxidizing agent is demonstrated by measuring the decay of fluorescence as a function of time for a 1 ppm Nile blue A solution after the addition of sodium hypochlorite.

  1. Mode-locked solid state lasers using diode laser excitation

    DOEpatents

    Holtom, Gary R.

    2012-03-06

    A mode-locked laser employs a coupled-polarization scheme for efficient longitudinal pumping by reshaped laser diode bars. One or more dielectric polarizers are configured to reflect a pumping wavelength having a first polarization and to reflect a lasing wavelength having a second polarization. An asymmetric cavity provides relatively large beam spot sizes in gain medium to permit efficient coupling to a volume pumped by a laser diode bar. The cavity can include a collimation region with a controlled beam spot size for insertion of a saturable absorber and dispersion components. Beam spot size is selected to provide stable mode locking based on Kerr lensing. Pulse durations of less than 100 fs can be achieved in Yb:KGW.

  2. Efficiency of Nd laser materials with laser diode pumping

    NASA Technical Reports Server (NTRS)

    Barnes, Norman P.; Cross, Patricia L.; Skolaut, Milton W., Jr.; Storm, Mark E.

    1990-01-01

    For pulsed laser-diode-pumped lasers, where efficiency is the most important issue, the choice of the Nd laser material makes a significant difference. The absorption efficiency, storage efficiency, and extraction efficiency for Nd:YAG, Nd:YLF, Nd:GSGG, Nd:BEL, Nd:YVO4, and Nd:glass are calculated. The materials are then compared under the assumption of equal quantum efficiency and damage threshold. Nd:YLF is found to be the best candidate for the application discussed here.

  3. Polarization methods for diode laser excitation of solid state lasers

    DOEpatents

    Holtom, Gary R.

    2008-11-25

    A mode-locked laser employs a coupled-polarization scheme for efficient longitudinal pumping by reshaped laser diode bars. One or more dielectric polarizers are configured to reflect a pumping wavelength having a first polarization and to reflect a lasing wavelength having a second polarization. A Yb-doped gain medium can be used that absorbs light having a first polarization and emits light having a second polarization. Using such pumping with laser cavity dispersion control, pulse durations of less than 100 fs can be achieved.

  4. Semiconductor Laser Diode Pumps for Inertial Fusion Energy Lasers

    SciTech Connect

    Deri, R J

    2011-01-03

    Solid-state lasers have been demonstrated as attractive drivers for inertial confinement fusion on the National Ignition Facility (NIF) at Lawrence Livermore National Laboratory (LLNL) and at the Omega Facility at the Laboratory for Laser Energetics (LLE) in Rochester, NY. For power plant applications, these lasers must be pumped by semiconductor diode lasers to achieve the required laser system efficiency, repetition rate, and lifetime. Inertial fusion energy (IFE) power plants will require approximately 40-to-80 GW of peak pump power, and must operate efficiently and with high system availability for decades. These considerations lead to requirements on the efficiency, price, and production capacity of the semiconductor pump sources. This document provides a brief summary of these requirements, and how they can be met by a natural evolution of the current semiconductor laser industry. The detailed technical requirements described in this document flow down from a laser ampl9ifier design described elsewhere. In brief, laser amplifiers comprising multiple Nd:glass gain slabs are face-pumped by two planar diode arrays, each delivering 30 to 40 MW of peak power at 872 nm during a {approx} 200 {micro}s quasi-CW (QCW) pulse with a repetition rate in the range of 10 to 20 Hz. The baseline design of the diode array employs a 2D mosaic of submodules to facilitate manufacturing. As a baseline, they envision that each submodule is an array of vertically stacked, 1 cm wide, edge-emitting diode bars, an industry standard form factor. These stacks are mounted on a common backplane providing cooling and current drive. Stacks are conductively cooled to the backplane, to minimize both diode package cost and the number of fluid interconnects for improved reliability. While the baseline assessment in this document is based on edge-emitting devices, the amplifier design does not preclude future use of surface emitting diodes, which may offer appreciable future cost reductions and

  5. Underwater Chaotic Lidar using Blue Laser Diodes

    NASA Astrophysics Data System (ADS)

    Rumbaugh, Luke K.

    The thesis proposes and explores an underwater lidar system architecture based on chaotic modulation of recently introduced, commercially available, low cost blue laser diodes. This approach is experimentally shown to allow accurate underwater impulse response measurements while eliminating the need for several major components typically found in high-performance underwater lidar systems. The proposed approach is to: 1. Generate wideband, noise-like intensity modulation signals using optical chaotic modulation of blue-green laser diodes, and then 2. Use this signal source to develop an underwater chaotic lidar system that uses no electrical signal generator, no electro-optic modulator, no optical frequency doubler, and no large-aperture photodetector. The outcome of this thesis is the demonstration of a new underwater lidar system architecture that could allow high resolution ranging, imaging, and water profiling measurements in turbid water, at a reduced size, weight, power and cost relative to state-of-the-art high-performance underwater lidar sensors. This work also makes contributions to the state of the art in optics, nonlinear dynamics, and underwater sensing by demonstrating for the first time: 1. Wideband noise-like intensity modulation of a blue laser diode using no electrical signal generator or electro-optic modulator. Optical chaotic modulation of a 462 nm blue InGaN laser diode by self-feedback is explored for the first time. The usefulness of the signal to chaotic lidar is evaluated in terms of bandwidth, modulation depth, and autocorrelation peak-to-sidelobe-ratio (PSLR) using both computer and laboratory experiments. In laboratory experiments, the optical feedback technique is shown to be effective in generating wideband, noise-like chaotic signals with strong modulation depth when the diode is operated in an external-cavity dominated state. The modulation signal strength is shown to be limited by the onset of lasing within the diode's internal

  6. Transcanalicular laser dacryocystorhinostomy using low energy 810 nm diode laser

    PubMed Central

    Gupta, Sanjiv K.; Kumar, Ajai; Agarwal, Swati; Pandey, Paritosh

    2012-01-01

    Background: Hypertrophic scarring may be a cause of failure after transcanalicular laser dacryocystorhinostomy (DCR) surgery. This hypertrophic scarring results from tissue charring and excessive coagulation, which may be caused by the high laser energy. We have evaluated the use of low energy settings to prevent hypertrophic scarring, for a successful outcome. Aims: To perform and evaluate transcanalicular laser DCR using low energy 810 nm diode laser. Design: Interventional, non-comparative, case series. Materials and Methods: Patients with nasolacrimal duct obstruction and chronic dacryocystitis, who needed DCR, and were fit for surgery under local anesthesia, were recruited to undergo transcanalicular laser DCR using a 810 nm diode laser. The outcome was measured by the patency of the lacrimal passage, as indicated by the relief in the symptoms and the patency on syringing at the last follow-up. The surgical time and surgical complications were noted. Statistical Analysis Used: Descriptive analysis. Results: The study included 94 patients. The average age was 30.1 years (range 15 - 69 years). Seventy (74.4%) patients were female. Eight patients had failed external DCR. Per-operative patency of the passage was obtained in all the patients. Average surgical time was seven minutes (5 – 18 minutes). At the end of the study period of one year, a successful outcome was seen in 85 patients (90.5%). There were eight patients of previous failed DCR surgeries, and six of them achieved a cure at the end of follow-up. Conclusions: Transcanalicular Laser DCR can be safely performed using a low power 810 nm diode laser. The surgery is elegant, minimally invasive, allows fast rehabilitation, and has an excellent success rate. PMID:23439888

  7. Qualification of Laser Diode Arrays for Mercury Laser Altimeter Mission

    NASA Technical Reports Server (NTRS)

    Stephen, Mark; Vasilyev, Aleksey; Schafer, John; Allan, Graham R.

    2004-01-01

    NASA's requirements for high reliability, high performance satellite laser instruments have driven the investigation of many critical components; specifically, 808 nm laser diode array (LDA) pump devices. The MESSENGER mission is flying the Mercury Laser Altimeter (MLA) which is a diode-pumped Nd:YAG laser instrument designed to map the topography of Mercury. The environment imposed on the instrument by the orbital dynamics places special requirements on the laser diode arrays. In order to limit the radiative heating of the satellite from the surface of Mercury, the satellite is designed to have a highly elliptical orbit. The satellite will heat near perigee and cool near apogee. The laser power is cycled during these orbits so that the laser is on for only 30 minutes (perigee) in a 12 hour orbit. The laser heats 10 C while powered up and cools while powered down. In order to simulate these operational conditions, we designed a test to measure the LDA performance while being temperature and power cycled. Though the mission requirements are specific to NASA and performance requirements are derived from unique operating conditions, the results are general and widely applicable. We present results on the performance of twelve LDAs operating for several hundred million pulses. The arrays are 100 watt, quasi-CW, conductively-cooled, 808 nm devices. Prior to testing, we fully characterize each device to establish a baseline for individual array performance and status. Details of this characterization can be found in reference. Arrays are divided into four groups and subjected to the temperature and power cycling matrix are shown.

  8. Method for partially coating laser diode facets

    NASA Technical Reports Server (NTRS)

    Dholakia, Anil R. (Inventor)

    1990-01-01

    Bars of integral laser diode devices cleaved from a wafer are placed with their p regions abutting and n regions abutting. A thin BeCu mask having alternate openings and strips of the same width as the end facets is used to mask the n region interfaces so that multiple bars can be partially coated over their exposed p regions with a reflective or partial reflective coating. The partial coating permits identification of the emitting facet from the fully coated back facet during a later device mounting procedure.

  9. Broadband External-Cavity Diode Laser

    NASA Technical Reports Server (NTRS)

    Pilgrim, Jeffrey S.

    2005-01-01

    A broadband external-cavity diode laser (ECDL) has been invented for use in spectroscopic surveys preparatory to optical detection of gases. Heretofore, commercially available ECDLs have been designed, in conjunction with sophisticated tuning assemblies, for narrow- band (and, typically, single-frequency) operation, as needed for high sensitivity and high spectral resolution in some gas-detection applications. However, for preparatory spectroscopic surveys, high sensitivity and narrow-band operation are not needed; in such cases, the present broadband ECDL offers a simpler, less-expensive, more-compact alternative to a commercial narrowband ECDL.

  10. Rubidium dimer destruction by a diode laser

    SciTech Connect

    Ban, T.; Aumiler, D.; Pichler, G.

    2005-02-01

    We observed rubidium dimer destruction by excitation of rubidium vapor with diode laser light tuned across the Rb D{sub 2} resonance line in a 2400 GHz tuning interval. The destruction was measured for rubidium atom concentrations in the (1-9)x10{sup 16} cm{sup -3} range, pump beam power up to 43 mW, and with a 5 Torr of the helium buffer gas. We discuss the physical mechanisms involved and specify the molecular pathways which may effectively lead to the observed dimer destruction.

  11. Multimode-diode-pumped gas (alkali-vapor) laser

    SciTech Connect

    Page, R H; Beach, R J; Kanz, V K

    2005-08-22

    We report the first demonstration of a multimode-diode-pumped gas laser--Rb vapor operating on the 795 nm resonance transition. Peak output of {approx}1 Watt was obtained using a volume-Bragg-grating stabilized pump diode array. The laser's output radiance exceeded the pump radiance by a factor greater than 2000. Power scaling (by pumping with larger diode arrays) is therefore possible.

  12. CO.sub.2 optically pumped distributed feedback diode laser

    DOEpatents

    Rockwood, Stephen D.

    1980-01-01

    A diode laser optically pumped by a CO.sub.2 coherent source. Interference fringes generated by feeding the optical pumping beam against a second beam, periodically alter the reflectivity of the diode medium allowing frequency variation of the output signal by varying the impingent angle of the CO.sub.2 laser beams.

  13. Means for phase locking the outputs of a surface emitting laser diode array

    NASA Technical Reports Server (NTRS)

    Lesh, James R. (Inventor)

    1987-01-01

    An array of diode lasers, either a two-dimensional array of surface emitting lasers, or a linear array of stripe lasers, is phase locked by a diode laser through a hologram which focuses the output of the diode laser into a set of distinct, spatially separated beams, each one focused onto the back facet of a separate diode laser of the array. The outputs of the diode lasers thus form an emitted coherent beam out of the front of the array.

  14. Diode laser for abdominal tissue cauterization

    NASA Astrophysics Data System (ADS)

    Durville, Frederic M.; Rediker, Robert H.; Connolly, Raymond J.; Schwaitzberg, Steven D.; Lantis, John

    1999-06-01

    We have developed a new device to effectively and quickly stop bleeding. The new device uses a small, 5 W diode laser to heat-up the tip of a modified medical forceps. The laser beam is totally contained within a protective enclosure, satisfying the requirements for a Class I laser system, which eliminates the need to protective eyewear. The new device is used in a manner similar to that of a bipolar electrocautery device. After visual location, the bleeding site or local vessel(s) is grabbed and clamped with the tips of the forceps-like instrument. The laser is then activated for a duration of typically 5 sec or until traditional visual or auditory clues such as local blubbling and popping indicate that the targeted site is effectively cauterized. When the laser is activated, the tip of the instrument, thus providing hemostasis. The new device was evaluated in animal models and compared with the monopolar and bipolar electrocautery, and also with the recently developed ultrasound technology. It has new been in clinical trials for abdominal surgery since September 1997.

  15. New diode wavelengths for pumping solid-state lasers

    SciTech Connect

    Skidmore, J.A.; Emanuel, M.A.; Beach, R.J.

    1995-01-01

    High-power laser-diode arrays have been demonstrated to be viable pump sources for solid-state lasers. The diode bars (fill factor of 0.7) were bonded to silicon microchannel heatsinks for high-average-power operation. Over 12 W of CW output power was achieved from a one cm AlGaInP tensile-strained single-quantum-well laser diode bar. At 690 nm, a compressively-strained single-quantum-well laser-diode array produced 360 W/cm{sup 2} per emitting aperture under CW operation, and 2.85 kW of pulsed power from a 3.8 cm{sup 2} emitting-aperture array. InGaAs strained single-quantum-well laser diodes emitting at 900 nm produced 2.8 kW pulsed power from a 4.4 cm{sup 2} emitting-aperture array.

  16. Digital control of diode laser for atmospheric spectroscopy

    NASA Technical Reports Server (NTRS)

    Menzies, R. T.; Rutledge, C. W. (Inventor)

    1985-01-01

    A system is described for remote absorption spectroscopy of trace species using a diode laser tunable over a useful spectral region of 50 to 200 cm(-1) by control of diode laser temperature over range from 15 K to 100 K, and tunable over a smaller region of typically 0.1 to 10 cm(-1) by control of the diode laser current over a range from 0 to 2 amps. Diode laser temperature and current set points are transmitted to the instrument in digital form and stored in memory for retrieval under control of a microprocessor during measurements. The laser diode current is determined by a digital to analog converter through a field effect transistor for a high degree of ambient temperature stability, while the laser diode temperature is determined by set points entered into a digital to analog converter under control of the microprocessor. Temperature of the laser diode is sensed by a sensor diode to provide negative feedback to the temperature control circuit that responds to the temperature control digital to analog converter.

  17. Photoluminescence excitation measurements using pressure-tuned laser diodes

    NASA Astrophysics Data System (ADS)

    Bercha, Artem; Ivonyak, Yurii; Medryk, Radosław; Trzeciakowski, Witold A.; Dybała, Filip; Piechal, Bernard

    2015-06-01

    Pressure-tuned laser diodes in external cavity were used as tunable sources for photoluminescence excitation (PLE) spectroscopy. The method was demonstrated in the 720 nm-1070 nm spectral range using a few commercial laser diodes. The samples for PLE measurements were quantum-well structures grown on GaAs and on InP. The method is superior to standard PLE measurements using titanium sapphire laser because it can be extended to any spectral range where anti-reflection coated laser diodes are available.

  18. Photoluminescence excitation measurements using pressure-tuned laser diodes

    SciTech Connect

    Bercha, Artem; Ivonyak, Yurii; Mędryk, Radosław; Trzeciakowski, Witold A. Dybała, Filip; Piechal, Bernard

    2015-06-15

    Pressure-tuned laser diodes in external cavity were used as tunable sources for photoluminescence excitation (PLE) spectroscopy. The method was demonstrated in the 720 nm-1070 nm spectral range using a few commercial laser diodes. The samples for PLE measurements were quantum-well structures grown on GaAs and on InP. The method is superior to standard PLE measurements using titanium sapphire laser because it can be extended to any spectral range where anti-reflection coated laser diodes are available.

  19. Tunable diode lasers for 3-30 micron infrared operation

    NASA Technical Reports Server (NTRS)

    Linden, K. J.

    1983-01-01

    The tunable diode laser is now widely used in high resolution infrared spectroscopy studies, taking into account laboratory and industrial applications. The present investigation is concerned with advances related to laser performance and reliability. The advances are the result of improvements in materials and device technologies. Reliability data for broad-area Pb(1-x)Sn(x)Se lasers are considered along with performance improvements in stripe-geometry lasers, laser performance at wavelengths above 25 microns, and laser performance at wavelengths below 4 microns. Attention is given to tunable Pb-salt infrared diode lasers, mesa-stripe geometry lasers of Pb(1-x)Sn(x)Se and PbS(1-x)Se(x), and long wavelength diode laser emission observed in both Pb(1-x)Sn(x)Te and Pb(1-x)Sn(x)Se.

  20. Laser diode ignition characteristics of Zirconium Potassium Perchlorate (ZPP)

    NASA Technical Reports Server (NTRS)

    Callaghan, Jerry D.; Tindol, Scot

    1993-01-01

    Hi-Shear Technology, Corp., (HSTC) has designed and built a Laser equivalent NASA Standard Initiator (LNSI). Langlie tests with a laser diode output initiating ZPP were conducted as a part of this effort. The test parameters include time to first pressure, laser power density requirements, and ignition time. The data from these laser tests on ZPP are presented.

  1. Computer-Assisted Experiments with a Laser Diode

    ERIC Educational Resources Information Center

    Kraftmakher, Yaakov

    2011-01-01

    A laser diode from an inexpensive laser pen (laser pointer) is used in simple experiments. The radiant output power and efficiency of the laser are measured, and polarization of the light beam is shown. The "h/e" ratio is available from the threshold of spontaneous emission. The lasing threshold is found using several methods. With a…

  2. High power laser diodes for the NASA direct detection laser transceiver experiment

    NASA Technical Reports Server (NTRS)

    Seery, Bernard D.; Holcomb, Terry L.

    1988-01-01

    High-power semiconductor laser diodes selected for use in the NASA space laser communications experiments are discussed. The diode selection rationale is reviewed, and the laser structure is shown. The theory and design of the third mirror lasers used in the experiments are addressed.

  3. Comparative efficiency analysis of GaN-based light-emitting diodes and laser diodes

    NASA Astrophysics Data System (ADS)

    Piprek, Joachim

    2016-07-01

    Nobel laureate Shuji Nakamura predicted in 2014 that GaN-based laser diodes are the future of solid state lighting. However, blue GaN-lasers still exhibit less than 40% wall-plug efficiency, while some GaN-based blue light-emitting diodes exceed 80%. This paper investigates non-thermal reasons behind this difference. The inherently poor hole conductivity of the Mg-doped waveguide cladding layer of laser diodes is identified as main reason for their low electrical-to-optical energy conversion efficiency.

  4. Ball Lenses Collimate And Focus Diode-Laser-Array Beams

    NASA Technical Reports Server (NTRS)

    Hemmati, Hamid

    1992-01-01

    Ball lenses used to collimate and focus pump light from array of diode lasers onto input face of solid-state laser. Experiments show ball lenses perform as well as, or better than, multiple-element lenses supplied heretofore as parts of commercial arrays of diode lasers. Offers advantages of relative simplicity and ease of fabrication, lower cost, lower weight, and less sensitivity to misalignment.

  5. Diode-Laser Phase Conjugation 03-FS-030 Final Report

    SciTech Connect

    Page, R H; Beach, R J; Payne, S A; Holzrichter, J F

    2005-02-14

    Arrays of lasers are often considered when a need exists to increase laser optical output power, for a variety of purposes. Similarly, individual semiconductor laser-diodes, generating 0.01-1.0 W each, are commonly placed in arrays in order to increase total optical power onto targeted objects. Examples of such usage are diode-laser pump arrays for solid-slab heat-capacity lasers, laser arrays for heat-treating materials, and arrays for efficient solid state laser systems. The commercial and defense communities also use such arrays for many applications from laser range-finders, laser designators, to laser machining systems, etc. However, the arraying process does not automatically increase ''focusable'' light on target (i.e., intensity/steradian). For those applications requiring the highest focusability, it is necessary that the collective output beam from arrays of individual lasers be phase-coherent. Under this condition, the individual laser-element optical outputs are ''fused together'' into a larger area, phase coherent (i.e., all wavefronts are ''in step''), high-power combined beam. The process of joining multiple laser beams together to produce a single coherent wave, is in general very difficult and seldom accomplished. Thus joining together many hundreds to thousands of beams from individual laser-diodes, in large arrays, is still an unsolved problem. There are 2 major reasons for this. Firstly, the phase of each output laser beam (i.e. the wave-fronts) from each laser diode often fluctuates within nanosecond time periods, making a control loop with sufficient bandwidth difficult to build. In fact, phase fluctuations (related to laser linewidth) limit the size of an extended system of arrayed diodes because of speed-of-light restrictions on information flow. Secondly, the output power per prior laser diode has been low ( < 1W,) so that the size, expense, and complexity of control systems for correcting a multitude of output phases of the individual

  6. Modular package for cooling a laser diode array

    DOEpatents

    Mundinger, David C.; Benett, William J.; Beach, Raymond J.

    1992-01-01

    A laser diode array is disclosed that includes a plurality of planar packages and active cooling. The laser diode array may be operated in a long duty cycle, or in continuous operation. A laser diode bar and a microchannel heat sink are thermally coupled in a compact, thin planar package having the laser diode bar located proximate to one edge. In an array, a number of such thin planar packages are secured together in a stacked configuration, in close proximity so that the laser diodes are spaced closely. The cooling means includes a microchannel heat sink that is attached proximate to the laser bar so that it absorbs heat generated by laser operation. To provide the coolant to the microchannels, each thin planar package comprises a thin inlet manifold and a thin outlet manifold connected to an inlet corridor and an outlet corridor. The inlet corridor comprises a hole extending through each of the packages in the array, and the outlet corridor comprises a hole extending through each of the packages in the array. The inlet and outlet corridors are connected to a conventional coolant circulation system. The laser diode array with active cooling has application as an optical pump for high power solid state lasers. Further, it can be incorporated in equipment such as communications devices and active sensors, and in military and space applications, and it can be useful in applications having space constraints and energy limitations.

  7. Continuous wave Cs diode pumped alkali laser pumped by single emitter narrowband laser diode.

    PubMed

    Zhdanov, B V; Venus, G; Smirnov, V; Glebov, L; Knize, R J

    2015-08-01

    This paper presents results of cooperative efforts on development of a continuous wave Cs diode pumped alkali laser with moderate output power, which can be considered as a prototype of the commercial device. The developed system operates at 895 nm with output power about 4 W and slope efficiency 28%. Measured turn on time of this system from the standby mode is about a minute. PMID:26329171

  8. Lead-strontium-chalcogenide diode laser

    SciTech Connect

    Partin, D.L.

    1988-01-26

    A large optical cavity quantum well double heterojunction semiconductor infrared diode laser is described having an active region layer sandwiched between two contiguous layers of monocrystalline semiconductive material. The laser exhibits current carrier and optical confinement for its active region layer but also exhibits increased operating temperature due to close lattice matching of face centered cubic monocrystalline layers forming the double heterojunctions. The laser comprises a monocrystalline buffer layer of a given conductivity type lead salt semiconductor containing strontium, selenium that has an energy band gap greater than, an index of refraction lesser than, and a lattice constant substantially equal to predetermined values of the active region layer, a monocrystalline active region layer on the buffer layer of a lead salt semiconductor containing a pn junction that has the predetermined energy and gap, index of refraction and lattice constant, and a confinement layer on the active region layer an opposite conductivity type lead salt semiconductor containing lesser amounts and smaller proportions of strontium and selenium that has an energy band gap greater than, an index of refraction smaller than, and a lattice constant substantially equal to the predetermined values.

  9. Microlens frames for laser diode arrays

    DOEpatents

    Skidmore, J.A.; Freitas, B.L.

    1999-07-13

    Monolithic microlens frames enable the fabrication of monolithic laser diode arrays and are manufactured inexpensively with high registration, and with inherent focal length compensation for any lens diameter variation. A monolithic substrate is used to fabricate a low-cost microlens array. The substrate is wet-etched or sawed with a series of v-grooves. The v-grooves can be created by wet-etching, by exploiting the large etch-rate selectivity of different crystal planes. The v-grooves provide a support frame for either cylindrical or custom-shaped microlenses. Because the microlens frames are formed by photolithographic semiconductor batch-processing techniques, they can be formed inexpensively over large areas with precise lateral and vertical registration. The v-groove has an important advantage for preserving the correct focus for lenses of varying diameter. 12 figs.

  10. Microlens frames for laser diode arrays

    DOEpatents

    Skidmore, Jay A.; Freitas, Barry L.

    1999-01-01

    Monolithic microlens frames enable the fabrication of monolithic laser diode arrays and are manufactured inexpensively with high registration, and with inherent focal length compensation for any lens diameter variation. A monolithic substrate is used to fabricate a low-cost microlens array. The substrate is wet-etched or sawed with a series of v-grooves. The v-grooves can be created by wet-etching, by exploiting the large etch-rate selectivity of different crystal planes. The v-grooves provide a support frame for either cylindrical or custom-shaped microlenses. Because the microlens frames are formed by photolithographic semiconductor batch-processing techniques, they can be formed inexpensively over large areas with precise lateral and vertical registration. The v-groove has an important advantage for preserving the correct focus for lenses of varying diameter.

  11. Active stabilization of a diode laser injection lock.

    PubMed

    Saxberg, Brendan; Plotkin-Swing, Benjamin; Gupta, Subhadeep

    2016-06-01

    We report on a device to electronically stabilize the optical injection lock of a semiconductor diode laser. Our technique uses as discriminator the peak height of the laser's transmission signal on a scanning Fabry-Perot cavity and feeds back to the diode current, thereby maintaining maximum optical power in the injected mode. A two-component feedback algorithm provides constant optimization of the injection lock, keeping it robust to slow thermal drifts and allowing fast recovery from sudden failures such as temporary occlusion of the injection beam. We demonstrate the successful performance of our stabilization method in a diode laser setup at 399 nm used for laser cooling of Yb atoms. The device eases the requirements on passive stabilization and can benefit any diode laser injection lock application, particularly those where several such locks are employed. PMID:27370428

  12. Active stabilization of a diode laser injection lock

    NASA Astrophysics Data System (ADS)

    Saxberg, Brendan; Plotkin-Swing, Benjamin; Gupta, Subhadeep

    2016-06-01

    We report on a device to electronically stabilize the optical injection lock of a semiconductor diode laser. Our technique uses as discriminator the peak height of the laser's transmission signal on a scanning Fabry-Perot cavity and feeds back to the diode current, thereby maintaining maximum optical power in the injected mode. A two-component feedback algorithm provides constant optimization of the injection lock, keeping it robust to slow thermal drifts and allowing fast recovery from sudden failures such as temporary occlusion of the injection beam. We demonstrate the successful performance of our stabilization method in a diode laser setup at 399 nm used for laser cooling of Yb atoms. The device eases the requirements on passive stabilization and can benefit any diode laser injection lock application, particularly those where several such locks are employed.

  13. Laser diode arrays for expanded mine detection capability

    NASA Astrophysics Data System (ADS)

    Crosby, Frank J.; Holloway, John H., Jr.; Petee, Danny A.; Stetson, Suzanne P.; Suiter, Harold R.; Tinsley, Ken R.

    2002-08-01

    A tactical unmanned aerial vehicle-size illumination system for enhanced mine detection capabilities has been designed, developed, integrated, and tested at the Coastal Systems Station. Airborne test flights were performed from June 12, 2001 to February 1, 2002. The Airborne Laser Diode Array Illuminator uses a single-wavelength compact laser diode array stack to provide illumination and is coupled with a pair of intensified CCD video cameras. The cameras were outfitted with various lenses and polarization filters to determine the benefits of each of the configurations. The first airborne demonstration of a laser diode illumination system is described and its effectiveness to perform nighttime mine detection operations is shown.

  14. Linewidth-tunable laser diode array for rubidium laser pumping

    SciTech Connect

    Li Zhiyong; Tan Rongqing; Xu Cheng; Li Lin

    2013-02-28

    To optimise the pump source for a high-power diodepumped rubidium vapour laser, we have designed a laser diode array (LDA) with a narrowed and tunable linewidth and an external cavity formed by two volume Bragg gratings (VBGs). Through controlling the temperature differences between the two VBGs, the LDA linewidth, which was 1.8 nm before mounting the two VBGs, was tunable from 100 pm to 0.2 nm, while the output power changed by no more than 4 %. By changing simultaneously the temperature in both VBGs, the centre wavelength in air of the linewidth-tunable LDA was tunable from 779.40 nm to 780.05 nm. (control of laser radiation parameters)

  15. Improving Reliability of High Power Quasi-CW Laser Diode Arrays for Pumping Solid State Lasers

    NASA Technical Reports Server (NTRS)

    Amzajerdian, Farzin; Meadows, Byron L.; Baker, Nathaniel R.; Barnes, Bruce W.; Baggott, Renee S.; Lockard, George E.; Singh, Upendra N.; Kavaya, Michael J.

    2005-01-01

    Most Lidar applications rely on moderate to high power solid state lasers to generate the required transmitted pulses. However, the reliability of solid state lasers, which can operate autonomously over long periods, is constrained by their laser diode pump arrays. Thermal cycling of the active regions is considered the primary reason for rapid degradation of the quasi-CW high power laser diode arrays, and the excessive temperature rise is the leading suspect in premature failure. The thermal issues of laser diode arrays are even more drastic for 2-micron solid state lasers which require considerably longer pump pulses compared to the more commonly used pump arrays for 1-micron lasers. This paper describes several advanced packaging techniques being employed for more efficient heat removal from the active regions of the laser diode bars. Experimental results for several high power laser diode array devices will be reported and their performance when operated at long pulsewidths of about 1msec will be described.

  16. An external cavity diode laser using a volume holographic grating

    NASA Astrophysics Data System (ADS)

    Chuang, Ho-Chiao; Chang, Chang-Ray; Chen, Chun-Chia; Chang, Ming-Shien

    2012-10-01

    This study presents an external cavity diode laser (ECDL) system, utilizing a volume holographic grating (VHG) and a microfabricated silicon flexure as the VHG holder. The laser design is aimed for easy assembly, controllability, and better stability of the laser cavity. The laser frequency was stabilized to a D2 transition of rubidium at 780.247 nm, with a mode-hop-free tuning range of 16 GHz and 9.6 GHz with and without feed-forward on the diode injection current. The measured linewidth was 850 kHz in 500 s, qualified for laser cooling experiments.

  17. Applications of microlens-conditioned laser diode arrays

    SciTech Connect

    Beach, R.J.; Emanuel, M.A.; Freitas, B.L.

    1995-01-01

    The ability to condition the radiance of laser diodes using shaped-fiber cylindrical-microlens technology has dramatically increased the number of applications that can be practically engaged by diode laser arrays. Lawrence Livermore National Laboratory (LLNL) has actively pursued optical efficiency and engineering improvements in this technology in an effort to supply large radiance-conditioned laser diode array sources for its own internal programs. This effort has centered on the development of a modular integrated laser diode packaging technology with the goal of enabling the simple and flexible construction of high average power, high density, two-dimensional arrays with integrated cylindrical microlenses. Within LLNL, the principal applications of microlens-conditioned laser diode arrays are as high intensity pump sources for diode pumped solid state lasers (DPSSLs). A simple end-pumping architecture has been developed and demonstrated that allows the radiation from microlens-conditioned, two-dimensional diode array apertures to be efficiently delivered to the end of rod lasers. To date, pump powers as high as 2.5 kW have been delivered to 3 mm diameter laser rods. Such high power levels are critical for pumping solid state lasers in which the terminal laser level is a Stark level lying in the ground state manifold. Previously, such systems have often required operation of the solid state gain medium at low temperature to freeze out the terminal laser Stark level population. The authors recently developed high intensity pump sources overcome this difficulty by effectively pumping to much higher inversion levels, allowing efficient operation at or near room temperature. Because the end-pumping technology is scalable in absolute power, the number of rare-earth ions and transitions that can be effectively accessed for use in practical DPSSL systems has grown tremendously.

  18. Multiple-Diode-Laser Gas-Detection Spectrometer

    NASA Technical Reports Server (NTRS)

    Webster, Christopher R.; Beer, Reinhard; Sander, Stanley P.

    1988-01-01

    Small concentrations of selected gases measured automatically. Proposed multiple-laser-diode spectrometer part of system for measuring automatically concentrations of selected gases at part-per-billion level. Array of laser/photodetector pairs measure infrared absorption spectrum of atmosphere along probing laser beams. Adaptable to terrestrial uses as monitoring pollution or control of industrial processes.

  19. High efficiency >26 W diode end-pumped Alexandrite laser.

    PubMed

    Teppitaksak, Achaya; Minassian, Ara; Thomas, Gabrielle M; Damzen, Michael J

    2014-06-30

    We show for the first time that multi-ten Watt operation of an Alexandrite laser can be achieved with direct red diode-pumping and with high efficiency. An investigation of diode end-pumped Alexandrite rod lasers demonstrates continuous-wave output power in excess of 26W, more than an order of magnitude higher than previous diode end-pumping systems, and slope efficiency 49%, the highest reported for a diode-pumped Alexandrite laser. Wavelength tuning from 730 to 792nm is demonstrated using self-seeding feedback from an external grating. Q-switched laser operation based on polarization-switching to a lower gain axis of Alexandrite has produced ~mJ-pulse energy at 1kHz pulse rate in fundamental TEM(00) mode. PMID:24977887

  20. GaN blue diode lasers: a spectroscopist's view

    NASA Astrophysics Data System (ADS)

    Leinen, H.; Glässner, D.; Metcalf, H.; Wynands, R.; Haubrich, D.; Meschede, D.

    We have characterized the spectroscopic properties of one of the first samples of blue-emitting diode lasers based on GaN. With such a laser diode operated inside a standard extended cavity arrangement we find a mode-hop free tuning range of more than 20 GHz and a linewidth of 10 MHz. Doppler-free spectroscopy on an indium atomic beam reveals the isotope shift between the two major indium isotopes as well as efficient optical pumping.

  1. Wavelength stabilized multi-kW diode laser systems

    NASA Astrophysics Data System (ADS)

    Köhler, Bernd; Unger, Andreas; Kindervater, Tobias; Drovs, Simon; Wolf, Paul; Hubrich, Ralf; Beczkowiak, Anna; Auch, Stefan; Müntz, Holger; Biesenbach, Jens

    2015-03-01

    We report on wavelength stabilized high-power diode laser systems with enhanced spectral brightness by means of Volume Holographic Gratings. High-power diode laser modules typically have a relatively broad spectral width of about 3 to 6 nm. In addition the center wavelength shifts by changing the temperature and the driving current, which is obstructive for pumping applications with small absorption bandwidths. Wavelength stabilization of high-power diode laser systems is an important method to increase the efficiency of diode pumped solid-state lasers. It also enables power scaling by dense wavelength multiplexing. To ensure a wide locking range and efficient wavelength stabilization the parameters of the Volume Holographic Grating and the parameters of the diode laser bar have to be adapted carefully. Important parameters are the reflectivity of the Volume Holographic Grating, the reflectivity of the diode laser bar as well as its angular and spectral emission characteristics. In this paper we present detailed data on wavelength stabilized diode laser systems with and without fiber coupling in the spectral range from 634 nm up to 1533 nm. The maximum output power of 2.7 kW was measured for a fiber coupled system (1000 μm, NA 0.22), which was stabilized at a wavelength of 969 nm with a spectral width of only 0.6 nm (90% value). Another example is a narrow line-width diode laser stack, which was stabilized at a wavelength of 1533 nm with a spectral bandwidth below 1 nm and an output power of 835 W.

  2. Investigation of communication laser diodes for the SILEX project

    NASA Astrophysics Data System (ADS)

    Menke, Bodo; Loeffler, Roland

    1989-10-01

    The Semiconductor Intersatellite Laser Experiment (SILEX) will construct an optical communications link over a range of 45,000 km, using 0.8-micron AlGaAs laser diodes capable of transmitting 65 Mbit/s. Numerous single-stripe diode types were furnished by manufacturers and subjected to measurements to establish conformity with the required far-field pattern spectrum spread under QPPM-modulation, mode-hopping, astigmatism, and rms wavefront error (WFE); WFE is demonstrated to be strongly affected by the laser window's introduction of strong spherical aberration. Three laser types have been chosen for breadboarding and accelerated life tests.

  3. Combless broadband terahertz generation with conventional laser diodes.

    PubMed

    Molter, D; Wagner, A; Weber, S; Jonuscheit, J; Beigang, R

    2011-03-14

    We present a novel technique to generate a continuous, combless broadband Terahertz spectrum with conventional low-cost laser diodes. A standard time-domain spectroscopy system using photoconductive antennas is pumped by the output of two tunable diode lasers. Using fine tuning for one laser and fine and coarse tuning for the second laser, difference frequency generation results in a continuous broadband THz spectrum. Fast coarse-tuning is achieved by a simple spatial light modulator introduced in an external cavity. The results are compared to multi-mode operation for THz generation. PMID:21445166

  4. Laser hazard analysis for various candidate diode lasers associated with the high resolution pulsed scanner.

    SciTech Connect

    Augustoni, Arnold L.

    2004-10-01

    A laser hazard analysis and safety assessment was performed for each various laser diode candidates associated with the High Resolution Pulse Scanner based on the ANSI Standard Z136.1-2000, American National Standard for the Safe Use of Lasers. A theoretical laser hazard analysis model for this system was derived and an Excel{reg_sign} spreadsheet model was developed to answer the 'what if questions' associated with the various modes of operations for the various candidate diode lasers.

  5. Diode-pumped Alexandrite ring laser for lidar applications

    NASA Astrophysics Data System (ADS)

    Munk, A.; Jungbluth, B.; Strotkamp, M.; Hoffmann, H.-D.; Poprawe, R.; Höffner, J.

    2016-03-01

    We present design and performance data of a diode-pumped Q-switched Alexandrite ring laser in the millijoule regime, which is longitudinally pumped by laser diode bar modules in the red spectral range. As a first step, a linear resonator was designed and characterized in qcw operation as well as in Q-switched operation. Based on these investigations, two separate linear cavities were set up, each with one Alexandrite crystal longitudinally pumped by one diode module. The two cavities are fused together and form a ring cavity which yields up to 6 mJ pulse burst energy in the qcw regime at 770 nm.

  6. Development and optimization of a diode laser for photodynamic therapy

    PubMed Central

    Lim, Hyun Soo

    2011-01-01

    Background and Aims: This study demonstrated the development of a laser system for cancer treatment with photodynamic therapy (PDT) based on a 635 nm laser diode. In order to optimize efficacy in PDT, the ideal laser system should deliver a homogeneous nondivergent light energy with a variable spot size and specific wavelength at a stable output power. Materials and Methods: We developed a digital laser beam controller using the constant current method to protect the laser diode resonator from the current spikes and other fluctuations, and electrical faults. To improve the PDT effects, the laser system should deliver stable laser energy in continuous wave (CW), burst mode and super burst mode, with variable irradiation times depending on the tumor type and condition. Results and Comments: The experimental results showed the diode laser system described herein was eminently suitable for PDT. The laser beam was homogeneous without diverging and the output power increased stably and in a linear manner from 10 mW to 1500 mW according to the increasing input current. Variation between the set and delivered output was less than 7%. Conclusions: The diode laser system developed by the author for use in PDT was compact, user-friendly, and delivered a stable and easily adjustable output power at a specific wavelength and user-set emission modes. PMID:24155529

  7. Reliability of high power laser diodes with external optical feedback

    NASA Astrophysics Data System (ADS)

    Bonsendorf, Dennis; Schneider, Stephan; Meinschien, Jens; Tomm, Jens W.

    2016-03-01

    Direct diode laser systems gain importance in the fields of material processing and solid-state laser pumping. With increased output power, also the influence of strong optical feedback has to be considered. Uncontrolled optical feedback is known for its spectral and power fluctuation effects, as well as potential emitter damage. We found that even intended feedback by use of volume Bragg gratings (VBG) for spectral stabilization may result in emitter lifetime reduction. To provide stable and reliable laser systems design, guidelines and maximum feedback ratings have to be found. We present a model to estimate the optical feedback power coupled back into the laser diode waveguide. It includes several origins of optical feedback and wide range of optical elements. The failure thresholds of InGaAs and AlGaAs bars have been determined not only at standard operation mode but at various working points. The influence of several feedback levels to laser diode lifetime is investigated up to 4000h. The analysis of the semiconductor itself leads to a better understanding of the degradation process by defect spread. Facet microscopy, LBIC- and electroluminescence measurements deliver detailed information about semiconductor defects before and after aging tests. Laser diode protection systems can monitor optical feedback. With this improved understanding, the emergency shutdown threshold can be set low enough to ensure laser diode reliability but also high enough to provide better machine usability avoiding false alarms.

  8. Wavelength-Agile External-Cavity Diode Laser for DWDM

    NASA Technical Reports Server (NTRS)

    Pilgrim, Jeffrey S.; Bomse, David S.

    2006-01-01

    A prototype external-cavity diode laser (ECDL) has been developed for communication systems utilizing dense wavelength- division multiplexing (DWDM). This ECDL is an updated version of the ECDL reported in Wavelength-Agile External- Cavity Diode Laser (LEW-17090), NASA Tech Briefs, Vol. 25, No. 11 (November 2001), page 14a. To recapitulate: The wavelength-agile ECDL combines the stability of an external-cavity laser with the wavelength agility of a diode laser. Wavelength is modulated by modulating the injection current of the diode-laser gain element. The external cavity is a Littman-Metcalf resonator, in which the zeroth-order output from a diffraction grating is used as the laser output and the first-order-diffracted light is retro-reflected by a cavity feedback mirror, which establishes one end of the resonator. The other end of the resonator is the output surface of a Fabry-Perot resonator that constitutes the diode-laser gain element. Wavelength is selected by choosing the angle of the diffracted return beam, as determined by position of the feedback mirror. The present wavelength-agile ECDL is distinguished by design details that enable coverage of all 60 channels, separated by 100-GHz frequency intervals, that are specified in DWDM standards.

  9. VBG controlled narrow bandwidth diode laser arrays

    NASA Astrophysics Data System (ADS)

    Levy, Joseph; Feeler, Ryan; Junghans, Jeremy

    2012-03-01

    Northrop Grumman Cutting Edge Optronics has developed large kilowatt class lensed laser diode arrays with subnanometer spectral width using Volume Bragg Grating (VBG) reflectors. Using these CW arrays with 100W bars at 885nm, excellent absorption in Nd:YAG is achieved, with lower thermal aberration than can be attained with 808nm pumps. The additional cost of the VBG reflectors and their alignment is partially offset by the much broader wavelength tolerance that is allowed in the unlocked array enhancing bar yield. Furthermore, the center wavelength of the arrays exhibit lower temperature sensitivity allowing the arrays to be operated over a wider current or temperature range than arrays without wavelength control. While there is an efficiency penalty associated with the addition of VBGs of 5-8%, it is more than compensated for by enhanced absorption, especially when used with narrowband absorption lines, such as 885nm in Nd:YAG. An overview of the design and manufacturing issues for arrays that are wavelength-locked with VBGs is presented along with the effect of post-construction hard UV exposure.

  10. Laser diode arrays for naval reconnaissance

    NASA Astrophysics Data System (ADS)

    Holloway, John H., Jr.; Crosby, Frank J.; Petee, Danny A.; Suiter, Harold R.; Witherspoon, Ned H.

    2003-09-01

    The Airborne Littoral Reconnaissance Technologies (ALRT) Project has demonstrated a nighttime operational minefield detection capability using commercial off-the-shelf high-power Laser Diode Arrays (LDAs). Historically, optical aerial detection of minefields has primarily been limited to daytime operations but LDAs promise compact and efficient lighting to allow for enhanced reconnaissance operations for future mine detection systems. When combined with high-resolution intensified imaging systems, LDAs can illuminate otherwise unseen areas. Future wavelength options will open the way for active multispectral imaging with LDAs. The Coastal Systems Station working for the Office of Naval Research on the ALRT project has designed, developed, integrated, and tested both prototype and commercial arrays from a Cessna airborne platform. Detailed test results show the ability to detect several targets of interest in a variety of background conditions. Initial testing of the prototype arrays, reported on last year, was completed and further investigations of the commercial versions were performed. Polarization-state detection studies were performed, and advantageous properties of the source-target-sensor geometry noted. Current project plans are to expand the field-of-view coverage for Naval exercises in the summer of 2003. This paper describes the test collection, data library products, array information, on-going test analysis results, and future planned testing of the LDAs.

  11. Airborne tunable diode laser measurements of formaldehyde

    NASA Astrophysics Data System (ADS)

    Fried, Alan; Wert, Bryan P.; Henry, Bruce; Drummond, James R.

    1999-09-01

    Accurate measurements of formaldehyde (CH 2O) in the atmosphere are essential to further our understanding of various atmospheric cycles involving hydrogen and carbon-containing species. Comparisons among independent measurements of this gas and between measurements and model calculations have raised numerous questions regarding the veracity of both endeavors. The present paper describes a long-term effort by our group to develop and employ tunable diode laser absorption spectroscopy (TDLAS) for highly accurate measurements of this gas on both ground-based and aircraft platforms. A highly sensitive and selective TDLAS system, which has successfully flown on three different aircraft campaigns, will be described. Many new hardware and software features, which have been implemented, now make it possible to detect ambient CH 2O concentrations as low as 55 parts-per-trillion employing a 20-s integration time. This paper will also discuss the many aspects associated with high accuracy and its verification, including a brief discussion of our aircraft sampling system and inlet surface effects.

  12. Optical communication with semiconductor laser diodes

    NASA Technical Reports Server (NTRS)

    Davidson, F.

    1987-01-01

    A 25 megabit/sec direct detection optical communication system that used Q=4 PPM signalling was constructed and its performance measured under laboratory conditions. The system used a single-mode AlGaAs laser diode transmitter and low noise silicon avalanche photodiode (APD) photodetector. Comparison of measured performance with the theoretical revealed that modeling the APD output as a Gaussian process under conditions of negligible background radiation and low (less than 10 to the -12 power A) APD bulk leakage currents leads to substantial underestimates of optimal APD gain to use and overestimates of system bit error probability. A procedure is given to numerically compute system performance which uses the more accurate Webb's Approximation of the exact Conradi distribution for the APD ouput signal that does not require excessive amounts of computer time (a few minutes of VAX 8600 CPU time per system operating point). Examples are given which illustrate the breakdown of the Gaussian approximation in assessing system performance. This system achieved a bit error probability of 10 to the -6 power at a received signal energy corresponding to an average of 60 absorbed photons/bit and optimal APD gain of 700.

  13. Optical communication with semiconductor laser diodes

    NASA Technical Reports Server (NTRS)

    Davidson, F.

    1988-01-01

    Slot timing recovery in a direct detection optical PPM communication system can be achieved by processing the photodetector waveform with a nonlinear device whose output forms the input to a phase lock group. The choice of a simple transition detector as the nonlinearity is shown to give satisfactory synchronization performance. The rms phase error of the recovered slot clock and the effect of slot timing jitter on the bit error probability were directly measured. The experimental system consisted of an AlGaAs laser diode (lambda = 834 nm) and a silicon avalanche photodiode (APD) photodetector and used Q=4 PPM signaling operated at a source data rate of 25 megabits/second. The mathematical model developed to characterize system performance is shown to be in good agreement with actual performance measurements. The use of the recovered slot clock in the receiver resulted in no degradation in receiver sensitivity compared to a system with perfect slot timing. The system achieved a bit error probability of 10 to the minus 6 power at received signal energies corresponding to an average of less than 60 detected photons per information bit.

  14. Diode-Pumped, Q-Switched, Frequency-Doubling Laser

    NASA Technical Reports Server (NTRS)

    Hemmati, Hamid; Lesh, James R.

    1993-01-01

    Experimental Q-switched, diode-pumped, intracavity-frequency-doubling laser generates pulses of radiation at wavelength of 532 nm from excitation at 810 nm. Principal innovative feature distinguishing laser from others of its type: pulsed operation of laser at pulse-repetition frequencies higher than reported previously. Folded resonator keeps most of second-harmonic radiation away from Q-switcher, laser crystal, and laser diodes. Folding mirror highly reflective at fundamental laser wavelength and highly transmissive at second-harmonic laser wavelength. By virtue of difference of about 0.6 percent between reflectivities in two polarizations at fundamental wavelength, folding mirror favors polarized oscillation at fundamental wavelength. This characteristic desirable for doubling of frequency in some intracavity crystals.

  15. 1047 nm laser diode master oscillator Nd:YLF power amplifier laser system

    NASA Technical Reports Server (NTRS)

    Yu, A. W.; Krainak, M. A.; Unger, G. L.

    1993-01-01

    A master oscillator power amplifier (MOPA) laser transmitter system at 1047 nm wavelength using a semiconductor laser diode and a diode pumped solid state (Nd:YLF) laser (DPSSL) amplifier is described. A small signal gain of 23 dB, a near diffraction limited beam, 1 Gbit/s modulation rates and greater than 0.6 W average power are achieved. This MOPA laser has the advantage of amplifying the modulation signal from the laser diode master oscillator (MO) with no signal degradation.

  16. Broad-Area Laser Diode With Fiber-Optic Injection

    NASA Technical Reports Server (NTRS)

    Hazel, Geoffrey; Mead, Patricia; Davis, Christopher; Cornwell, Donald

    1992-01-01

    Fiber-optic injection-locked broad-area laser diode features single-mode output via fiber-optic injection and serves as compact, rugged, high-power near-infrared source. Useful in free-space and fiber-optic communication links, as communication-receiver preamplifier, and pump source for solid-state lasers.

  17. Diode-pumped laser with improved pumping system

    DOEpatents

    Chang, Jim J.

    2004-03-09

    A laser wherein pump radiation from laser diodes is delivered to a pump chamber and into the lasing medium by quasi-three-dimensional compound parabolic concentrator light channels. The light channels have reflective side walls with a curved surface and reflective end walls with a curved surface. A flow tube between the lasing medium and the light channel has a roughened surface.

  18. High average power diode pumped solid state lasers for CALIOPE

    SciTech Connect

    Comaskey, B.; Halpin, J.; Moran, B.

    1994-07-01

    Diode pumping of solid state media offers the opportunity for very low maintenance, high efficiency, and compact laser systems. For remote sensing, such lasers may be used to pump tunable non-linear sources, or if tunable themselves, act directly or through harmonic crystals as the probe. The needs of long range remote sensing missions require laser performance in the several watts to kilowatts range. At these power performance levels, more advanced thermal management technologies are required for the diode pumps. The solid state laser design must now address a variety of issues arising from the thermal loads, including fracture limits, induced lensing and aberrations, induced birefringence, and laser cavity optical component performance degradation with average power loading. In order to highlight the design trade-offs involved in addressing the above issues, a variety of existing average power laser systems are briefly described. Included are two systems based on Spectra Diode Laboratory`s water impingement cooled diode packages: a two times diffraction limited, 200 watt average power, 200 Hz multi-rod laser/amplifier by Fibertek, and TRW`s 100 watt, 100 Hz, phase conjugated amplifier. The authors also present two laser systems built at Lawrence Livermore National Laboratory (LLNL) based on their more aggressive diode bar cooling package, which uses microchannel cooler technology capable of 100% duty factor operation. They then present the design of LLNL`s first generation OPO pump laser for remote sensing. This system is specified to run at 100 Hz, 20 nsec pulses each with 300 mJ, less than two times diffraction limited, and with a stable single longitudinal mode. The performance of the first testbed version will be presented. The authors conclude with directions their group is pursuing to advance average power lasers. This includes average power electro-optics, low heat load lasing media, and heat capacity lasers.

  19. Novel diode laser-based sensors for gas sensing applications

    NASA Technical Reports Server (NTRS)

    Tittel, F. K.; Lancaster, D. G.; Richter, D.

    2000-01-01

    The development of compact spectroscopic gas sensors and their applications to environmental sensing will be described. These sensors employ mid-infrared difference-frequency generation (DFG) in periodically poled lithium niobate (PPLN) crystals pumped by two single-frequency solid state lasers such as diode lasers, diode-pumped solid state, and fiber lasers. Ultrasensitive, highly selective, and real-time measurements of several important atmospheric trace gases, including carbon monoxide, nitrous oxide, carbon dioxide, formaldehyde [correction of formaldehye], and methane, have been demonstrated.

  20. Computer Processing Of Tunable-Diode-Laser Spectra

    NASA Technical Reports Server (NTRS)

    May, Randy D.

    1991-01-01

    Tunable-diode-laser spectrometer measuring transmission spectrum of gas operates under control of computer, which also processes measurement data. Measurements in three channels processed into spectra. Computer controls current supplied to tunable diode laser, stepping it through small increments of wavelength while processing spectral measurements at each step. Program includes library of routines for general manipulation and plotting of spectra, least-squares fitting of direct-transmission and harmonic-absorption spectra, and deconvolution for determination of laser linewidth and for removal of instrumental broadening of spectral lines.

  1. Light polarization experiments with a diode laser pointer

    NASA Astrophysics Data System (ADS)

    Benenson, Raymond E.

    2000-01-01

    Polarized light has many uses: glare reduction, stress analysis, microscope image enhancement, thin-film characterization, astronomy, saccharimetry, and atomic spectroscopy. Here we discuss introductory polarized light measurements in which a diode laser pointer replaces the more frequently used polarized He-Ne laser. A diode laser has been used in introductory optics experiments, and in a more advanced polarization-reflection experiment. Its strong collimated beam is completely polarized and, being free of infrared radiation, it permits Polaroid sheets to be used successfully with semiconductor detectors.

  2. Diode-pumped solid state laser for inertial fusion energy

    SciTech Connect

    Payne, S.A.; Krupke, W.F.; Orth, C.D.

    1994-11-01

    The authors evaluate the prospect for development of a diode-pumped solid-state-laser driver in an inertial fusion energy power plant. Using a computer code, they predict that their 1 GWe design will offer electricity at 8.6 cents/kW {center_dot} hr with the laser operating at 8.6% efficiency and the recycled power level at 31%. The results of their initial subscale experimental testbed of a diode-pumped solid state laser are encouraging, demonstrating good efficiencies and robustness.

  3. Management of chronic generalized periodontitis using diode laser

    PubMed Central

    Dixit, Santosh; Doshi, Yogesh; Shah, Mona Udayan; Dabholkar, Charuta Sadanand

    2016-01-01

    The aim of this study was to evaluate the effect of a diode laser with nonsurgical periodontal therapy on chronic periodontitis. The patient, a 37-year-old female, with chronic periodontitis reported to the private dental clinic. Her health history indicated that she had good general health. The periodontal examination included a gingival index and complete periodontal probing depth with William's graduated probe. She was treated with 940 nm diode laser and scaling and root planning. Assessment was done after 6 months following laser therapy; the probing depths improved; gain in clinical attachment levels; no inflammation; the tissue tone was good, showing increased stippling. PMID:27041846

  4. Narrow spectral width laser diode for metastable argon atoms pumping

    NASA Astrophysics Data System (ADS)

    Gao, Jun; Li, Bin; Wang, Xinbing; Zuo, Duluo

    2016-03-01

    Diode laser pump source with narrow emitting spectrum for optically pumped metastable rare gas laser (OPRGL) of argon was achieved by employing a complex external cavity coupled with volume Bragg grating (VBG). A commercially available c-mount laser diode with rated power of 6 W was used and studied in both the free running mode and VBG external cavity. The maximum output power of 3.9 W with FWHM less than 25 pm and peak wavelength locked around 811.53 nm was obtained from the VBG external cavity laser diode. Precise control of VBG temperature enabled fine tuning of the emission wavelength over a range of 450 pm. Future researches on OPRGL of argon will benefit from it.

  5. Thermally widely tunable laser diodes with distributed feedback

    SciTech Connect

    Todt, R.; Jacke, T.; Meyer, R.; Amann, M.-C.

    2005-07-11

    A thermally widely tunable buried heterostructure laser diode with distributed feedback (DFB) is demonstrated. This device requires only two tuning currents for wide quasicontinuous wavelength tuning, thereby facilitating easy and fast device calibration and control. Furthermore, being based on regular DFB laser fabrication technology, it is readily manufacturable. By using window structures instead of cleaved facets plus antireflection coatings, a regular tuning behavior has been achieved for a DFB-like widely tunable laser diode with only two tuning currents. The laser diode covers the wavelength range between 1552 and 1602 nm. Requiring side-mode suppression ratio and output power above 30 dB and 10 mW, respectively, a wavelength range of 43 nm is accessible.

  6. Photoporation and cell transfection using a violet diode laser

    NASA Astrophysics Data System (ADS)

    Paterson, L.; Agate, B.; Comrie, M.; Ferguson, R.; Lake, T. K.; Morris, J. E.; Carruthers, A. E.; Brown, C. T. A.; Sibbett, W.; Bryant, P. E.; Gunn-Moore, F.; Riches, A. C.; Dholakia, Kishan

    2005-01-01

    The introduction and subsequent expression of foreign DNA inside living mammalian cells (transfection) is achieved by photoporation with a violet diode laser. We direct a compact 405 nm laser diode source into an inverted optical microscope configuration and expose cells to 0.3 mW for 40 ms. The localized optical power density of ~1200 MW/m2 is six orders of magnitude lower than that used in femtosecond photoporation (~104 TW/m2). The beam perforates the cell plasma membrane to allow uptake of plasmid DNA containing an antibiotic resistant gene as well as the green fluorescent protein (GFP) gene. Successfully transfected cells then expand into clonal groups which are used to create stable cell lines. The use of the violet diode laser offers a new and simple poration technique compatible with standard microscopes and is the simplest method of laser-assisted cell poration reported to date.

  7. Thermal Regime of High-power Laser Diodes

    NASA Astrophysics Data System (ADS)

    Bezotosnyi, V. V.; Krokhin, O. N.; Oleshchenko, V. A.; Pevtsov, V. F.; Popov, Yu. M.; Cheshev, E. A.

    We discuss the design and application perspectives of different crystal, ceramic and composite-type submounts with thermo-compensating properties as well as submounts from materials with high thermal conductivity for overcoming thermal problem in high-power laser diodes (LD) and improving thermal management of other high-power optoelectronic and electronic semiconductor devices. Thermal fields in high-power laser diodes were calculated in 3 D thermal model at CW operation for some heatsink designs taking into account the experimental dependence of laser total efficiency against pumping current in order to extend the range of reliable operation up to thermal loads 20-30 W and corresponding output optical power up to 15-20 W for 100 μm stripe laser diodes.

  8. Despeckling fly's eye homogenizer for single mode laser diodes.

    PubMed

    Mizuyama, Yosuke; Harrison, Nathan; Leto, Riccardo

    2013-04-01

    A novel fly's eye homogenizer for single mode laser diodes is presented. This technology overcomes the speckle problem that has been unavoidable for fly's eye homogenizers used with coherent light sources such as single mode laser diodes. Temporal and spatial coherence are reduced simultaneously by introducing short pulse driving of the injection current and a staircase element. Speckle has been dramatically reduced to 5% from 87% compared to a conventional system and a uniform laser line illumination was obtained by the proposed fly's eye homogenizer with a single mode UV-blue laser diode for the first time. A new spatial coherence function was mathematically formulated to model the proposed system and was applied to a partially coherent intensity formula that was newly developed in this study from Wolf's theory to account for the results. PMID:23571997

  9. A Direct Diode Laser System Using a Planar Lightwave Circuit

    NASA Astrophysics Data System (ADS)

    Hasegawa, Kazuo; Matsubara, Hiroyuki; Ichikawa, Tadashi; Maeda, Mitsutoshi; Ito, Hiroshi

    2008-08-01

    In this paper we propose a direct diode laser (DDL) system consisting of laser diode (LD) bars, a planar lightwave circuit (PLC), and an optical fiber. We have developed a PLC as an optical power combiner and an LD mounting technology that is suitable for coupling to the PLC. A DDL system is presented that consists of six LD-PLC optical modules for the laser-welding of highly heat-resistant plastics. The total output power is in the 200 W class, with a spot diameter of 5.52 mm for the major axis and 5.00 mm for the minor axis at a focal length of 50 mm. The total output efficiency is 60.9% from the laser diode to the welding torch.

  10. Feasibility of supersonic diode pumped alkali lasers: Model calculations

    SciTech Connect

    Barmashenko, B. D.; Rosenwaks, S.

    2013-04-08

    The feasibility of supersonic operation of diode pumped alkali lasers (DPALs) is studied for Cs and K atoms applying model calculations, based on a semi-analytical model previously used for studying static and subsonic flow DPALs. The operation of supersonic lasers is compared with that measured and modeled in subsonic lasers. The maximum power of supersonic Cs and K lasers is found to be higher than that of subsonic lasers with the same resonator and alkali density at the laser inlet by 25% and 70%, respectively. These results indicate that for scaling-up the power of DPALs, supersonic expansion should be considered.

  11. Advancement of High Power Quasi-CW Laser Diode Arrays For Space-based Laser Instruments

    NASA Technical Reports Server (NTRS)

    Amzajerdian, Farzin; Meadows, Byron L.; Baker, nathaniel R.; Baggott, Renee S.; Singh, Upendra N.; Kavaya, Michael J.

    2004-01-01

    Space-based laser and lidar instruments play an important role in NASA s plans for meeting its objectives in both Earth Science and Space Exploration areas. Almost all the lidar instrument concepts being considered by NASA scientist utilize moderate to high power diode-pumped solid state lasers as their transmitter source. Perhaps the most critical component of any solid state laser system is its pump laser diode array which essentially dictates instrument efficiency, reliability and lifetime. For this reason, premature failures and rapid degradation of high power laser diode arrays that have been experienced by laser system designers are of major concern to NASA. This work addresses these reliability and lifetime issues by attempting to eliminate the causes of failures and developing methods for screening laser diode arrays and qualifying them for operation in space.

  12. Diode pumped alkali vapor lasers for high power applications

    NASA Astrophysics Data System (ADS)

    Zweiback, J.; Krupke, B.; Komashko, A.

    2008-02-01

    General Atomics has been engaged in the development of diode pumped alkali vapor lasers. We have been examining the design space looking for designs that are both efficient and easily scalable to high powers. Computationally, we have looked at the effect of pump bandwidth on laser performance. We have also looked at different lasing species. We have used an alexandrite laser to study the relative merits of different designs. We report on the results of our experimental and computational studies.

  13. Direct pumping of ultrashort Ti:sapphire lasers by a frequency doubled diode laser

    NASA Astrophysics Data System (ADS)

    Müller, André; Jensen, Ole B.; Unterhuber, Angelika; Le, Tuan; Stingl, Andreas; Hasler, Karl-Heinz; Sumpf, Bernd; Erbert, Götz; Andersen, Peter E.; Petersen, Paul M.

    2011-12-01

    A simple and robust diode laser system emitting 1.28 W of green light suitable for pumping an ultrafast Ti:sapphire laser is presented. To classify our results, the diode laser is compared to a standard, commercially available diode pumped solid-state (DPSS) laser system pumping the same oscillator. When using our diode laser system, the optical conversion efficiencies from green to near-infrared light reduces to 75 % of the values achieved with the commercial pump laser. Despite this reduction the overall efficiency of the Ti:sapphire laser is still increased by a factor > 2 due to the superior electro-optical efficiency of the diode laser. Autocorrelation measurements show that pulse widths of less than 20 fs can be expected with an average power of 52 mW when using our laser. These results indicate the high potential of direct diode laser pumped Ti:sapphire lasers to be used in applications like retinal optical coherence tomography (OCT) or pumping of photonic crystal fibers for CARS (coherent anti-stokes Raman spectroscopy) microscopy.

  14. Thermal compensator for closed-cycle helium refrigerator. [assuring constant temperature for an infrared laser diode

    NASA Technical Reports Server (NTRS)

    Jennings, D. E.; Hillman, J. J. (Inventor)

    1979-01-01

    The wave length of an infrared, semiconductor laser diode having an output frequency that is dependent on the diode temperature is maintained substantially constant by maintaining the diode temperature constant. The diode is carried by a cold tip of a closed cycle helium refrigerator. The refrigerator has a tendency to cause the temperature of the cold tip to oscillate. A heater diode and a sensor diode are placed on a thermal heat sink that is the only highly conductive thermal path between the laser diode and the cold tip. The heat sink has a small volume and low thermal capacitance so that the sensing diode is at substantially the same temperature as the heater diode and substantially no thermal lag exists between them. The sensor diode is connected in a negative feedback circuit with the heater diode so that the tendency of the laser diode to thermally oscillate is virtually eliminated.

  15. A simplified 461-nm laser system using blue laser diodes and a hollow cathode lamp for laser cooling of Sr

    PubMed Central

    Shimada, Yosuke; Chida, Yuko; Ohtsubo, Nozomi; Aoki, Takatoshi; Takeuchi, Makoto; Kuga, Takahiro; Torii, Yoshio

    2013-01-01

    We develop a simplified light source at 461 nm for laser cooling of Sr without frequency-doubling crystals but with blue laser diodes. An anti-reflection coated blue laser diode in an external cavity (Littrow) configuration provides an output power of 40 mW at 461 nm. Another blue laser diode is used to amplify the laser power up to 110 mW by injection locking. For frequency stabilization, we demonstrate modulation-free polarization spectroscopy of Sr in a hollow cathode lamp. The simplification of the laser system achieved in this work is of great importance for the construction of transportable optical lattice clocks. PMID:23822327

  16. Reliability of High Power Laser Diode Arrays Operating in Long Pulse Mode

    NASA Technical Reports Server (NTRS)

    Amzajerdian, Farzin; Meadows, Byron L.; Barnes, Bruce W.; Lockard, George E.; Singh, Upendra N.; Kavaya, Michael J.; Baker, Nathaniel R.

    2006-01-01

    Reliability and lifetime of quasi-CW laser diode arrays are greatly influenced by their thermal characteristics. This paper examines the thermal properties of laser diode arrays operating in long pulse duration regime.

  17. Materials processing with a high power diode laser

    SciTech Connect

    Li, L.; Lawrence, J.; Spencer, J.T.

    1996-12-31

    This paper reports on work exploring the feasibility of a range of materials processing applications using a Diomed 60W diode laser delivered through a 600{mu}m diameter optical fibre to a 3 axis CNC workstation. The applications studied include: marking/engraving natural stones (marble and granite), marking ceramic tiles, sealing tile grouts, cutting and marking glass, marking/engraving wood, stripping paint and lacquer, and welding metallic wires. The study shows that even at the present limited power level of diode lasers, many materials processing applications can be accomplished with satisfactory results. Through the study an initial understanding of interaction of high power diode laser (HPDL) beam with various materials has been gained. Also, within the paper basic beam characteristics, and current R&D activities in HPDL technology and materials processing applications are reviewed.

  18. Microchannel heatsinks for high average power laser diode arrays

    SciTech Connect

    Beach, R.; Benett, B.; Freitas, B.; Ciarlo, D.; Sperry, V.; Comaskey, B.; Emanuel, M.; Solarz, R.; Mundinger, D.

    1992-01-01

    Detailed performance results and fabrication techniques for an efficient and low thermal impedance laser diode array heatsink are presented. High duty factor or even CW operation of fully filled laser diode arrays is enabled at high average power. Low thermal impedance is achieved using a liquid coolant and laminar flow through microchannels. The microchannels are fabricated in silicon using a photolithographic pattern definition procedure followed by anisotropic chemical etching. A modular rack-and-stack architecture is adopted for the heatsink design allowing arbitrarily large two-dimensional arrays to be fabricated and easily maintained. The excellent thermal control of the microchannel cooled heatsinks is ideally suited to pump array requirements for high average power crystalline lasers because of the stringent temperature demands that result from coupling the diode light to several nanometers wide absorption features characteristic of leasing ions in crystals.

  19. Overview on new diode lasers for defense applications

    NASA Astrophysics Data System (ADS)

    Neukum, Joerg

    2012-11-01

    Diode lasers have a broad wavelength range, from the visible to beyond 2.2μm. This allows for various applications in the defense sector, ranging from classic pumping of DPSSL in range finders or target designators, up to pumping directed energy weapons in the 50+ kW range. Also direct diode applications for illumination above 1.55μm, or direct IR countermeasures are of interest. Here an overview is given on some new wavelengths and applications which are recently under discussion. In this overview the following aspects are reviewed: • High Power CW pumps at 808 / 880 / 940nm • Pumps for DPAL - Diode Pumped Alkali Lasers • High Power Diode Lasers in the range < 1.0 μm • Scalable Mini-Bar concept for high brightness fiber coupled modules • The Light Weight Fiber Coupled module based on the Mini-Bar concept Overall, High Power Diode Lasers offer many ways to be used in new applications in the defense market.

  20. Comparative hazard evaluation of near-infrared diode lasers.

    PubMed

    Marshall, W J

    1994-05-01

    Hazard evaluation methods from various laser protection standards differ when applied to extended-source, near-infrared lasers. By way of example, various hazard analyses are applied to laser training systems, which incorporate diode lasers, specifically those that assist in training military or law enforcement personnel in the proper use of weapons by simulating actual firing by the substitution of a beam of near-infrared energy for bullets. A correct hazard evaluation of these lasers is necessary since simulators are designed to be directed toward personnel during normal use. The differences among laser standards are most apparent when determining the hazard class of a laser. Hazard classification is based on a comparison of the potential exposures with the maximum permissible exposures in the 1986 and 1993 versions of the American National Standard for the Safe Use of Lasers, Z136.1, and the accessible emission limits of the federal laser product performance standard. Necessary safety design features of a particular system depend on the hazard class. The ANSI Z136.1-1993 standard provides a simpler and more accurate hazard assessment of low-power, near-infrared, diode laser systems than the 1986 ANSI standard. Although a specific system is evaluated, the techniques described can be readily applied to other near-infrared lasers or laser training systems. PMID:8175359

  1. High duty cycle hard soldered kilowatt laser diode arrays

    NASA Astrophysics Data System (ADS)

    Klumel, Genady; Karni, Yoram; Oppenheim, Jacob; Berk, Yuri; Shamay, Moshe; Tessler, Renana; Cohen, Shalom

    2010-02-01

    High-brightness laser diode arrays operating at a duty cycle of 10% - 20% are in ever-increasing demand for the optical pumping of solid state lasers and directed energy applications. Under high duty-cycle operation at 10% - 20%, passive (conductive) cooling is of limited use, while micro-coolers using de-ionized cooling water can considerably degrade device reliability. When designing and developing actively-cooled collimated laser diode arrays for high duty cycle operation, three main problems should be carefully addressed: an effective local and total heat removal, a minimization of packaging-induced and operational stresses, and high-precision fast axis collimation. In this paper, we present a novel laser diode array incorporating a built-in tap water cooling system, all-hard-solder bonded assembly, facet-passivated high-power 940 nm laser bars and tight fast axis collimation. By employing an appropriate layout of water cooling channels, careful choice of packaging materials, proper design of critical parts, and active optics alignment, we have demonstrated actively-cooled collimated laser diode arrays with extended lifetime and reliability, without compromising their efficiency, optical power density, brightness or compactness. Among the key performance benchmarks achieved are: 150 W/bar optical peak power at 10% duty cycle, >50% wallplug efficiency and <1° collimated fast axis divergence. A lifetime of >0.5 Ghots with <2% degradation has been experimentally proven. The laser diode arrays have also been successfully tested under harsh environmental conditions, including thermal cycling between -20°C and 40°C and mechanical shocks at 500g acceleration. The results of both performance and reliability testing bear out the effectiveness and robustness of the manufacturing technology for high duty-cycle laser arrays.

  2. Blue laser diode (LD) and light emitting diode (LED) applications

    NASA Astrophysics Data System (ADS)

    Bergh, Arpad A.

    2004-09-01

    The family of blue LEDs, edge emitting and surface emitting lasers, enable a number of applications. Blue lasers are used in digital applications such as optical storage in high density DVDs. The resolution of the spot size and hence the storage density is diffraction limited and is inversely proportional to the square of the wavelength of the laser. Other applications include printing, optical scanners, and high-resolution photo-lithography.As light emitters, blue LEDs are used for signaling and in direct view large area emissive displays. They are also making inroads into signage and LCD back-lighting, mobile platforms, and decorative accent lighting in curtains, furniture, etc.Blue LEDs produce white light either with phosphor wavelength converters or in combination with red and green LEDs. The full potential of LED light sources will require three devices to enable complete control over color and intensity.Sensing and medical/bio applications have a major impact on home security, on monitoring the environment, and on health care. New emerging diagnostic and therapeutic applications will improve the quality and reduce the cost of health care.

  3. A portable lidar using a diode-pumped YAG laser

    NASA Technical Reports Server (NTRS)

    Takeuchi, N.; Okumura, H.; Sugita, T.; Matsumoto, H.; Yamaguchi, S.

    1992-01-01

    A Mie lidar system is technically established and is used for monitoring air pollution, stratospheric and boundary layer aerosol distribution, plume dispersion, visibility, and the study of atmospheric structure and cloud physics. However, a lidar system is not widely used because of its cumbersome handling and unwieldy portability. Although the author developed a laser diode lidar system based on RM-CW technique, it has a limit of measurement distance. Here we report the development of an all solid Mie lidar system using a diode-pumped Nd:YAG laser and a Si-APD detector. This was constructed as a prototype of a handy lidar system.

  4. Arrangement for damping the resonance in a laser diode

    NASA Technical Reports Server (NTRS)

    Katz, J.; Yariv, A.; Margalit, S. (Inventor)

    1985-01-01

    An arrangement for damping the resonance in a laser diode is described. This arrangement includes an additional layer which together with the conventional laser diode form a structure (35) of a bipolar transistor. Therein, the additional layer serves as the collector, the cladding layer next to it as the base, and the active region and the other cladding layer as the emitter. A capacitor is connected across the base and the collector. It is chosen so that at any frequency above a certain selected frequency which is far below the resonance frequency the capacitor impedance is very low, effectively shorting the base to the collector.

  5. Comparison of violet diode laser with CO II laser in surgical performance of soft tissues

    NASA Astrophysics Data System (ADS)

    Hatayama, H.; Kato, J.; Inoue, A.; Akashi, G.; Hirai, Y.

    2007-02-01

    The violet diode laser (405nm) has recently begun to be studied for surgical use and authors reported the soft tissue could be effectively incised by irradiation power of even less than 1W. The wavelength of this laser is highly absorbed by hemoglobin, myoglobin or melanin pigment. Cutting or ablating soft tissues by lower irradiation power might be preferable for wound healing. The CO II laser is known to be preferable for low invasive treatment of soft tissues and widely used. The CO II laser light (10.6μm) is highly absorbed by water and proper for effective ablation of soft tissues. In this paper, we report the comparison of the violet diode laser with the CO II laser in surgical performance of soft tissues. Tuna tissue was used as an experimental sample. In the case of the violet diode laser, extensive vaporization of tissue was observed after the expansion of coagulation. Carbonization of tissue was observed after the explosion. On the other hand, consecutive vaporization and carbonization were observed immediately after irradiation in the case of CO II laser. The violet diode laser could ablate tissue equivalently with the CO II laser and coagulate larger area than the CO II laser. Therefore the violet diode laser might be expectable as a surgical tool which has excellent hemostatis.

  6. High-efficiency side diode pumped breech mount laser ignition

    NASA Astrophysics Data System (ADS)

    Hardy, Christopher R.; Guo, Baoping; Myers, Michael J.; Myers, John D.

    2007-09-01

    Breech Mounted Lasers (BMLs) have been successfully used to demonstrate laser ignition of howitzer propellant charges including bag, stick, and the Modular Artillery Charge System (MACS). BMLs have been integrated and tested on many artillery systems, including the US Army's M109A6 Paladin, M198, M777 Light Weight, Crusader, and Non-Line-of-Sight Cannon (NLOS-C). Until now, these lasers have been relatively large and inefficient systems based on a flashlamp pumped Nd:YAG laser design. Modern vehicle platforms will require smaller, more efficient lasers that can operate under increased shock and vibration loads. Kigre's new DPSS (Diode Pumped Solid State) lasers appear to meet these requirements. In this work we provide an evaluation of HESP (High Efficiency Side Pumped) DPSS laser design and performance with regard to its application as a practical artillery laser ignition system.

  7. Diode Laser Velocity Measurements by Modulated Filtered Rayleigh Scattering

    NASA Technical Reports Server (NTRS)

    Mach, J. J.; Varghese, P. L.; Jagodzinski, J. J.

    1999-01-01

    The ability of solid-state lasers to be tuned in operating frequency at MHz rates by input current modulation, while maintaining a relatively narrow line-width, has made them useful for spectroscopic measurements. Their other advantages include low cost, reliability, durability, compact size, and modest power requirements, making them a good choice for a laser source in micro-gravity experiments in drop-towers and in flight. For their size, they are also very bright. In a filtered Rayleigh scattering (FRS) experiment, a diode laser can be used to scan across an atomic or molecular absorption line, generating large changes in transmission at the resonances for very small changes in frequency. The hyperfine structure components of atomic lines of alkali metal vapors are closely spaced and very strong, which makes such atomic filters excellent candidates for sensitive Doppler shift detection and therefore for high-resolution velocimetry. In the work we describe here we use a Rubidium vapor filter, and work with the strong D(sub 2) transitions at 780 nm that are conveniently accessed by near infrared diode lasers. The low power output of infrared laser diodes is their primary drawback relative to other laser systems commonly used for velocimetry. However, the capability to modulate the laser frequency rapidly and continuously helps mitigate this. Using modulation spectroscopy and a heterodyne detection scheme with a lock-in amplifier, one can extract sub-microvolt signals occurring at a specific frequency from a background that is orders of magnitude stronger. The diode laser modulation is simply achieved by adding a small current modulation to the laser bias current. It may also be swept repetitively in wavelength using an additional lower frequency current ramp.

  8. Characterization and development of an extended cavity tunable laser diode

    NASA Astrophysics Data System (ADS)

    Traptilisa, Fnu

    A laser diode emits a narrow range of frequencies. However, drifts in frequency occur over time due to many factors like changes in laser temperature, current, mechanical vibrations in the apparatus, etc. These frequency drifts make the laser unsuitable for experiments that require high frequency stability. We have used an atomic transition in rubidium as a frequency reference and used Doppler free saturated spectroscopy to observe the reference peak. We have designed an electronic locking circuit that operates the diode laser at a specific frequency. It keeps the laser at that frequency for a long period of time with very few or no drifts. We have constructed and characterized an extended cavity diode laser that costs significantly less than a commercial unit. It is much more compact with performance comparable to that of a commercial unit. It can be used in undergraduate and graduate optics laboratories where commercial units are cost prohibitive. The various components of the set-up are discussed, and the basic principles behind the function and operation of this versatile device are explained. We designed a servo loop filter circuit, which is used to stabilize the frequency of the laser to an atomic reference frequency. We also generated an error signal using a technique similar to the Pound Hall Drever technique and then feedback the error signal in the loop filter circuit.

  9. Method and system for homogenizing diode laser pump arrays

    DOEpatents

    Bayramian, Andy J

    2013-10-01

    An optical amplifier system includes a diode pump array including a plurality of semiconductor diode laser bars disposed in an array configuration and characterized by a periodic distance between adjacent semiconductor diode laser bars. The periodic distance is measured in a first direction perpendicular to each of the plurality of semiconductor diode laser bars. The diode pump array provides a pump output propagating along an optical path and characterized by a first intensity profile measured as a function of the first direction and having a variation greater than 10%. The optical amplifier system also includes a diffractive optic disposed along the optical path. The diffractive optic includes a photo-thermo-refractive glass member. The optical amplifier system further includes an amplifier slab having an input face and position along the optical path and separated from the diffractive optic by a predetermined distance. A second intensity profile measured at the input face of the amplifier slab as a function of the first direction has a variation less than 10%.

  10. Method and system for homogenizing diode laser pump arrays

    DOEpatents

    Bayramian, Andrew James

    2016-05-03

    An optical amplifier system includes a diode pump array including a plurality of semiconductor diode laser bars disposed in an array configuration and characterized by a periodic distance between adjacent semiconductor diode laser bars. The periodic distance is measured in a first direction perpendicular to each of the plurality of semiconductor diode laser bars. The diode pump array provides a pump output propagating along an optical path and characterized by a first intensity profile measured as a function of the first direction and having a variation greater than 10%. The optical amplifier system also includes a diffractive optic disposed along the optical path. The diffractive optic includes a photo-thermo-refractive glass member. The optical amplifier system further includes an amplifier slab having an input face and position along the optical path and separated from the diffractive optic by a predetermined distance. A second intensity profile measured at the input face of the amplifier slab as a function of the first direction has a variation less than 10%.

  11. Dual-Wavelength Internal-Optically-Pumped Semiconductor Laser Diodes

    NASA Astrophysics Data System (ADS)

    Green, Benjamin

    Dual-wavelength laser sources have various existing and potential applications in wavelength division multiplexing, differential techniques in spectroscopy for chemical sensing, multiple-wavelength interferometry, terahertz-wave generation, microelectromechanical systems, and microfluidic lab-on-chip systems. In the drive for ever smaller and increasingly mobile electronic devices, dual-wavelength coherent light output from a single semiconductor laser diode would enable further advances and deployment of these technologies. The output of conventional laser diodes is however limited to a single wavelength band with a few subsequent lasing modes depending on the device design. This thesis investigates a novel semiconductor laser device design with a single cavity waveguide capable of dual-wavelength laser output with large spectral separation. The novel dual-wavelength semiconductor laser diode uses two shorter- and longer-wavelength active regions that have separate electron and hole quasi-Fermi energy levels and carrier distributions. The shorter-wavelength active region is based on electrical injection as in conventional laser diodes, and the longer-wavelength active region is then pumped optically by the internal optical field of the shorter-wavelength laser mode, resulting in stable dual-wavelength laser emission at two different wavelengths quite far apart. Different designs of the device are studied using a theoretical model developed in this work to describe the internal optical pumping scheme. The carrier transport and separation of the quasi-Fermi distributions are then modeled using a software package that solves Poisson's equation and the continuity equations to simulate semiconductor devices. Three different designs are grown using molecular beam epitaxy, and broad-area-contact laser diodes are processed using conventional methods. The modeling and experimental results of the first generation design indicate that the optical confinement factor of the

  12. Discretely tunable single-frequency fibre Bragg grating diode laser

    SciTech Connect

    Duraev, V P; Lutts, G B; Nedelin, E T; Sumarokov, M A; Medvedkov, O I; Vasil'ev, S A

    2007-12-31

    The results of the development of discretely tunable single-frequency semiconductor lasers with the external cavity based on fibre Bragg gratings (FBGs) written in a single-mode fibre are presented. It is shown, in particular, that, by using an external cavity semiconductor laser with the output mirror representing a superposition of several FBGs with different resonance wavelengths, it is possible to obtain lasing at one or several wavelengths simultaneously by varying the injection current and (or) the temperature of the active area of the laser diode. (lasers)

  13. Diode laser treatment for osteal and osteoarticular panaritium

    NASA Astrophysics Data System (ADS)

    Privalov, Valery A.; Krochek, Ivan V.; Lappa, Alexander V.; Poltavsky, Andrew N.; Antonov, Andrew A.

    2005-08-01

    Laser osteoperforation method, initially developed for treatment of osteomyelitis, was successfully applied to 66 patients with osteal and osteoarticular panaritium. The procedure consisted in perforation of the affected phalanx with diode laser radiation (wavelength 970nm; average power 10-12W; pulse mode 100/50 ms), delivered through quartz monofiber. Additional laser induced thermotherapy (power 2-3W; continuous mode) was fulfilled for persistent fistulas. In comparison with conventional surgery, laser osteoperforation provided faster pain relieve, edema dissipation, wound and fistula closure; good functional results; decreasing of disability cases number.

  14. High brightness diode-pumped organic solid-state laser

    NASA Astrophysics Data System (ADS)

    Zhao, Zhuang; Mhibik, Oussama; Nafa, Malik; Chénais, Sébastien; Forget, Sébastien

    2015-02-01

    High-power, diffraction-limited organic solid-state laser operation has been achieved in a vertical external cavity surface-emitting organic laser (VECSOL), pumped by a low-cost compact blue laser diode. The diode-pumped VECSOLs were demonstrated with various dyes in a polymer matrix, leading to laser emissions from 540 nm to 660 nm. Optimization of both the pump pulse duration and output coupling leads to a pump slope efficiency of 11% for a DCM based VECSOLs. We report output pulse energy up to 280 nJ with 100 ns long pump pulses, leading to a peak power of 3.5 W in a circularly symmetric, diffraction-limited beam.

  15. AlGaAs diode pumped tunable chromium lasers

    DOEpatents

    Krupke, William F.; Payne, Stephen A.

    1992-01-01

    An all-solid-state laser system is disclosed wherein the laser is pumped in the longwave wing of the pump absorption band. By utilizing a laser material that will accept unusually high dopant concentrations without deleterious effects on the crystal lattice one is able to compensate for the decreased cross section in the wing of the absorption band, and the number of pump sources which can be used with such a material increases correspondingly. In a particular embodiment a chromium doped colquiriite-structure crystal such as Cr:LiSrAlF.sub.6 is the laser material. The invention avoids the problems associated with using AlGaInP diodes by doping the Cr:LiSrAlF.sub.6 heavily to enable efficient pumping in the longwave wing of the absorption band with more practical AlGaAs diodes.

  16. High brightness diode-pumped organic solid-state laser

    SciTech Connect

    Zhao, Zhuang; Mhibik, Oussama; Nafa, Malik; Chénais, Sébastien; Forget, Sébastien

    2015-02-02

    High-power, diffraction-limited organic solid-state laser operation has been achieved in a vertical external cavity surface-emitting organic laser (VECSOL), pumped by a low-cost compact blue laser diode. The diode-pumped VECSOLs were demonstrated with various dyes in a polymer matrix, leading to laser emissions from 540 nm to 660 nm. Optimization of both the pump pulse duration and output coupling leads to a pump slope efficiency of 11% for a DCM based VECSOLs. We report output pulse energy up to 280 nJ with 100 ns long pump pulses, leading to a peak power of 3.5 W in a circularly symmetric, diffraction-limited beam.

  17. Polarization/Spatial Combining of Laser-Diode Pump Beams

    NASA Technical Reports Server (NTRS)

    Gelsinger, Paul; Liu, Duncan

    2008-01-01

    A breadboard version of an optical beam combiner is depicted which make it possible to use the outputs of any or all of four multimode laser diodes to pump a non-planar ring oscillator (NPRO) laser. The output of each laser diode has a single-mode profile in the meridional plane containing an axis denoted the 'fast' axis and a narrower multimode profile in the orthogonal meridional plane, which contains an axis denoted the 'slow' axis and a narrower multimode profile in the orthogonal meridional plane, which contains an axis denoted the 'slow' axis. One of the purposes served by the beam-combining optics is to reduce the fast-axis numerical aperture (NA) of the laser-diode output to match the NA of the optical fiber. Along the slow axis, the unmodified laser-diode NA is already well matched to the fiber optic NA, so no further slow-axis beam shaping is needed. In this beam combiner, the laser-diode outputs are collimated by aspherical lenses, then half-wave plates and polarizing beam splitters are used to combine the four collimated beams into two beams. Spatial combination of the two beams and coupling into the optical fiber is effected by use of anamorphic prisms, mirrors, and a focusing lens. The anamorphic prisms are critical elements in the NA-matching scheme, in that they reduce the fast-axis beam width to 1/6 of its original values. Inasmuch as no slow-axis beam shaping is needed, the collimating and focusing lenses are matched for 1:1 iumaging. Because these lenses are well corrected for infinite conjugates the combiner offers diffraction-limited performance along both the fast and slow axes.

  18. Monolithic laser diode structure for microwave generation

    SciTech Connect

    Goldberg, L.; Weller, J.F.

    1990-03-06

    This patent describes an apparatus. It comprises: a semiconductor substrate; a semiconductor master laser and first and second semiconductor slave lasers fabricated adjacent to each other on the semiconductor substrate. The master laser generating an optical output at a frequency f{sub 0} and sidebands at multiples of {Delta}f, the first and second slave lasers being tuned to approximately coincide with first and second preselected sidebands of the master laser; and means for respectively injection-locking the first and second slave lasers to the first and second preselected sidebands.

  19. Inner retinal damage after exposure to green diode laser during a laser show

    PubMed Central

    Jeon, Sohee; Lee, Won Ki

    2014-01-01

    Here we report two cases of retinal damage after exposure to a 510 nm laser diode during a laser show. The first patient was a 20-year-old female who presented with decreased visual acuity in her right eye after visiting a dance party with a diode laser show (wavelength 510 nm, power 2 mW), although she did not directly see the light. Retinal examination revealed a sub-internal limiting membrane hemorrhage and a small laser burn. The second patient was a 20-year-old female who visited for decreased vision in her left eye. She described similar events as the first patient. An exposure to green diode laser can result in retinal damage. It is strongly recommended that certified personnel operate laser devices used in indoor laser shows under strict regulation. PMID:25506208

  20. Injection locking of a high power ultraviolet laser diode for laser cooling of ytterbium atoms

    SciTech Connect

    Hosoya, Toshiyuki; Miranda, Martin; Inoue, Ryotaro; Kozuma, Mikio

    2015-07-15

    We developed a high-power laser system at a wavelength of 399 nm for laser cooling of ytterbium atoms with ultraviolet laser diodes. The system is composed of an external cavity laser diode providing frequency stabilized output at a power of 40 mW and another laser diode for amplifying the laser power up to 220 mW by injection locking. The systematic method for optimization of our injection locking can also be applied to high power light sources at any other wavelengths. Our system does not depend on complex nonlinear frequency-doubling and can be made compact, which will be useful for providing light sources for laser cooling experiments including transportable optical lattice clocks.

  1. Near-ultraviolet laser diodes for brilliant ultraviolet fluorophore excitation.

    PubMed

    Telford, William G

    2015-12-01

    Although multiple lasers are now standard equipment on most modern flow cytometers, ultraviolet (UV) lasers (325-365 nm) remain an uncommon excitation source for cytometry. Nd:YVO4 frequency-tripled diode pumped solid-state lasers emitting at 355 nm are now the primary means of providing UV excitation on multilaser flow cytometers. Although a number of UV excited fluorochromes are available for flow cytometry, the cost of solid-state UV lasers remains prohibitively high, limiting their use to all but the most sophisticated multilaser instruments. The recent introduction of the brilliant ultraviolet (BUV) series of fluorochromes for cell surface marker detection and their importance in increasing the number of simultaneous parameters for high-dimensional analysis has increased the urgency of including UV sources in cytometer designs; however, these lasers remain expensive. Near-UV laser diodes (NUVLDs), a direct diode laser source emitting in the 370-380 nm range, have been previously validated for flow cytometric analysis of most UV-excited probes, including quantum nanocrystals, the Hoechst dyes, and 4',6-diamidino-2-phenylindole. However, they remain a little-used laser source for cytometry, despite their significantly lower cost. In this study, the ability of NUVLDs to excite the BUV dyes was assessed, along with their compatibility with simultaneous brilliant violet (BV) labeling. A NUVLD emitting at 375 nm was found to excite most of the available BUV dyes at least as well as a UV 355 nm source. This slightly longer wavelength did produce some unwanted excitation of BV dyes, but at sufficiently low levels to require minimal additional compensation. NUVLDs are compact, relatively inexpensive lasers that have higher power levels than the newest generation of small 355 nm lasers. They can, therefore, make a useful, cost-effective substitute for traditional UV lasers in multicolor analysis involving the BUV and BV dyes. PMID:25930008

  2. Investigation of the light field of a semiconductor diode laser.

    PubMed

    Ankudinov, A V; Yanul, M L; Slipchenko, S O; Shelaev, A V; Dorozhkin, P S; Podoskin, A A; Tarasov, I S

    2014-10-20

    Scanning near-field optical microscopy was applied to study, with sub-wavelength spatial resolution, the near- and the far-field distributions of propagating modes from a high-power laser diode. Simple modeling was also performed and compared with experimental results. The simulated distributions were consistent with the experiment and permitted clarification of the configuration of the transverse modes of the laser. PMID:25401675

  3. Electrically injected visible vertical cavity surface emitting laser diodes

    DOEpatents

    Schneider, R.P.; Lott, J.A.

    1994-09-27

    Visible laser light output from an electrically injected vertical cavity surface emitting laser (VSCEL) diode is enabled by the addition of phase-matching spacer layers on either side of the active region to form the optical cavity. The spacer layers comprise InAlP which act as charge carrier confinement means. Distributed Bragg reflector layers are formed on either side of the optical cavity to act as mirrors. 5 figs.

  4. Even Illumination from Fiber-Optic-Coupled Laser Diodes

    NASA Technical Reports Server (NTRS)

    Howard, Richard T.

    2006-01-01

    A method of equipping fiber-optic-coupled laser diodes to evenly illuminate specified fields of view has been proposed. The essence of the method is to shape the tips of the optical fibers into suitably designed diffractive optical elements. One of the main benefits afforded by the method would be more nearly complete utilization of the available light. Diffractive optics is a relatively new field of optics in which laser beams are shaped by use of diffraction instead of refraction.

  5. Fiber Coupled Laser Diodes with Even Illumination Pattern

    NASA Technical Reports Server (NTRS)

    Howard, Richard T. (Inventor)

    2007-01-01

    An optical fiber for evenly illuminating a target. The optical fiber is coupled to a laser emitting diode and receives laser light. The la ser light travels through the fiber optic and exits at an exit end. T he exit end has a diffractive optical pattern formed thereon via etch ing, molding or cutting, to reduce the Gaussian profile present in co nventional fiber optic cables The reduction of the Gaussian provides an even illumination from the fiber optic cable.

  6. Electrically injected visible vertical cavity surface emitting laser diodes

    SciTech Connect

    Schneider, Richard P.; Lott, James A.

    1994-01-01

    Visible laser light output from an electrically injected vertical cavity surface emitting laser (VSCEL) diode is enabled by the addition of phase-matching spacer layers on either side of the active region to form the optical cavity. The spacer layers comprise InAlP which act as charge carrier confinement means. Distributed Bragg reflector layers are formed on either side of the optical cavity to act as mirrors.

  7. Diode laser osteoperforation and its application to osteomyelitis treatment

    NASA Astrophysics Data System (ADS)

    Privalov, Valeriy A.; Krochek, Igor V.; Lappa, Alexander V.

    2001-10-01

    Laser osteoperforation, previously studied in experiment in rabbits at treatment for acute purulent osteomyelitis (Privalov V. et.al., SPIE Proc., v.3565., pp. 72-79), was applied in clinic to 36 patients with chronic purulent osteomyelitis and to 6 patients (children) with acute haematogenic osteomyelitis. Diode lasers of 805 and 980 nm wavelength were used. There was achieved full recovery in all acute cases, and stable remission in chronic cases during all the observation period (1 - 2.5 years).

  8. Unstable-Resonator Oscillator/Amplifier Diode Laser

    NASA Technical Reports Server (NTRS)

    Lang, Robert J.; Mittelstein, Michael; Tiberio, Richard C.; Forouhar, Siamak; Crawford, Deborah

    1994-01-01

    Fabricated as single-chip integrated circuit. Device based partly on concept proved in commercial solid-state lasers: using unstable-resonator oscillator to define electromagnetic mode and, following oscillator, traveling-wave amplifier to generate high power. Mode-definition and power-amplification functions optimized separately. Hyperbolic-grating, unstable-resonator oscillator/amplifier diode laser produces single-longitudinal-mode, broad, laterally coherent, diffraction-limited, high-power beam.

  9. SPECTRAL MEASUREMENTS OF GASEOUS SULFURIC ACID USING TUNABLE DIODE LASERS

    EPA Science Inventory

    Using a tunable diode laser spectrometer with a spectral resolution of about 10 to the -4 power/cm, the important central portions of the two infrared absorption bands of H2SO4 at 8.2 micrometers (1222/cm) and 11.3 micrometers (880/cm) have been scanned at low pressure (approxima...

  10. Diode-laser-based lidars: the next generation

    NASA Astrophysics Data System (ADS)

    Vujkovic-Cvijin, Pajo; Cooper, David E.; Van der Laan, Jan E.; Warren, Russell E.

    1999-10-01

    The work on the development of compact diode laser-based lidar systems at SRI International is reviewed. Two systems, a pseudorandom modulation lidar, and a mobile remote sensor for natural gas pipeline leak detection are described in detail, and experimental results are presented. Methods to enhance signal detection by digital filtering are also reviewed.

  11. Molecular oxygen detection using frequency modulation diode laser spectroscopy

    NASA Technical Reports Server (NTRS)

    Wang, Liang-Guo; Sachse, Glen

    1990-01-01

    A high-sensitivity spectroscopic measurement of O2 using two-tone frequency modulation spectroscopy with a GaAlAs diode laser is presented. An oxygen sensor based on this technique would be non-intrusive, compact and possess high sensitivity and fast time response.

  12. Diode laser arrays for dynamic infrared scene projection

    NASA Astrophysics Data System (ADS)

    Beasley, D. Brett; Cooper, John B.

    1993-08-01

    A novel concept for dynamic IR scene projection using IR diode lasers has been developed. This technology offers significant cost and performance advantages over other currently available projector technologies. Performance advantages include high dynamic range, multiple wavebands, and high frame rates. A projector system which utilizes a 16-element linear array has been developed and integrated into the millimeter wave/infrared (MMW/IR) hardware-in-the-loop (HWIL) facility at the US Army Missile Command's (USAMICOM's) Research, Development, and Engineering Center (RDEC). This projector has demonstrated dynamic range in excess of 105, apparent temperatures greater than 2500 degree(s)C, and nanosecond response times. Performance characteristics for this projector system are presented in the paper. Designs for projectors to test other IR sensor configurations, including FPAs, have been developed and are presented as well. The FPA design consists of a linear array of diode lasers scanned by a polygon mirror. This low-cost projector offers high resolution, high contrast 2-D scenes at up to 10 KHz frame rates. Simulation of active IR countermeasures is another promising application of diode laser projector systems. The diode laser is capable of simulating flares or virtually any IR jammer waveform.

  13. A TUNABLE DIODE LASER STACK MONITOR FOR SULFURIC ACID VAPOR

    EPA Science Inventory

    A field prototype instrument for continuous in-situ monitoring of sulfuric acid vapor in industrial smoke stacks has been developed. The method of detection is dual wavelength differential absorption in the infrared. Two tunable diode lasers are locked to two specific frequencies...

  14. Fiber-optic interferometer using frequency-modulated laser diodes

    NASA Technical Reports Server (NTRS)

    Beheim, G.

    1986-01-01

    This paper describes an electrically passive fiber-optic interferometer which uses dual frequency-modulated laser diodes. Experimental results show that this type of interferometer can attain a displacement range of 100 micron with subnanometer resolution. This technique can serve as the basis for a number of high-precision fiber-optic sensors.

  15. 946 nm Diode Pumped Laser Produces 100mJ

    NASA Technical Reports Server (NTRS)

    Axenson, Theresa J.; Barnes, Norman P.; Reichle, Donald J., Jr.

    2000-01-01

    An innovative approach to obtaining high energy at 946 nm has yielded 101 mJ of laser energy with an optical-to-optical slope efficiency of 24.5%. A single gain module resonator was evaluated, yielding a maximum output energy of 50 mJ. In order to obtain higher energy a second gain module was incorporated into the resonator. This innovative approach produced un-surprised output energy of 101 mJ. This is of utmost importance since it demonstrates that the laser output energy scales directly with the number of gain modules. Therefore, higher energies can be realized by simply increasing the number of gain modules within the laser oscillator. The laser resonator incorporates two gain modules into a folded "M-shaped" resonator, allowing a quadruple pass gain within each rod. Each of these modules consists of a diode (stack of 30 microlensed 100 Watt diode array bars, each with its own fiber lens) end-pumping a Nd:YAG laser rod. The diode output is collected by a lens duct, which focuses the energy into a 2 mm diameter flat to flat octagonal pump area of the laser crystal. Special coatings have been developed to mitigate energy storage problems, including parasitic lasing and amplified spontaneous emission (ASE), and encourage the resonator to operate at the lower gain transition at 946 nm.

  16. Chirped microlens arrays for diode laser circularization and beam expansion

    NASA Astrophysics Data System (ADS)

    Schreiber, Peter; Dannberg, Peter; Hoefer, Bernd; Beckert, Erik

    2005-08-01

    Single-mode diode lasers are well-established light sources for a huge number of applications but suffer from astigmatism, beam ellipticity and large manufacturing tolerances of beam parameters. To compensate for these shortcomings, various approaches like anamorphic prism pairs and cylindrical telescopes for circularization as well as variable beam expanders based on zoomed telescopes for precise adjustment of output beam parameters have been employed in the past. The presented new approach for both beam circularization and expansion is based on the use of microlens arrays with chirped focal length: Selection of lenslets of crossed cylindrical microlens arrays as part of an anamorphic telescope enables circularization, astigmatism correction and divergence tolerance compensation of diode lasers simultaneously. Another promising application of chirped spherical lens array telescopes is stepwise variable beam expansion for circular laser beams of fiber or solid-state lasers. In this article we describe design and manufacturing of beam shaping systems with chirped microlens arrays fabricated by polymer-on-glass replication of reflow lenses. A miniaturized diode laser module with beam circularization and astigmatism correction assembled on a structured ceramics motherboard and a modulated RGB laser-source for photofinishing applications equipped with both cylindrical and spherical chirped lens arrays demonstrate the feasibility of the proposed system design approach.

  17. LASERS: Low-threshold short-cavity diode laser for a miniature atomic clock

    NASA Astrophysics Data System (ADS)

    Kargapol'tsev, Sergei V.; Velichansky, Vladimir L.; Vasil'ev, V. V.; Kobyakova, M. Sh; Morozyuk, A. V.; Shiryaeva, N. V.; Konyaev, V. P.

    2009-06-01

    Short-cavity diode lasers (SCDLs) emitting at the 894-nm D1 line of caesium are developed. Low threshold currents and power consumption will make it possible to use these lasers in chip-size atomic clocks (CSACs) and magnetometers. The SCDL parameters are comparable with the parameters of surface-emitting lasers.

  18. In-volume heating using high-power laser diodes

    NASA Astrophysics Data System (ADS)

    Denisenkov, Valentin S.; Kiyko, Vadim V.; Vdovin, Gleb V.

    2015-03-01

    High-power lasers are useful instruments suitable for applications in various fields; the most common industrial applications include cutting and welding. We propose a new application of high-power laser diodes as in-bulk heating source for food industry. Current heating processes use surface heating with different approaches to make the heat distribution more uniform and the process more efficient. High-power lasers can in theory provide in-bulk heating which can sufficiently increase the uniformity of heat distribution thus making the process more efficient. We chose two media (vegetable fat and glucose) for feasibility experiments. First, we checked if the media have necessary absorption coefficients on the wavelengths of commercially available laser diodes (940-980 nm). This was done using spectrophotometer at 700-1100 nm which provided the dependences of transmission from the wavelength. The results indicate that vegetable fat has noticeable transmission dip around 925 nm and glucose has sufficient dip at 990 nm. Then, after the feasibility check, we did numerical simulation of the heat distribution in bulk using finite elements method. Based on the results, optimal laser wavelength and illuminator configuration were selected. Finally, we carried out several pilot experiments with high-power diodes heating the chosen media.

  19. Small core fiber coupled 60-W laser diode

    NASA Astrophysics Data System (ADS)

    Fernie, Douglas P.; Mannonen, Ilkka; Raven, Anthony L.

    1995-05-01

    Semiconductor laser diodes are compact, efficient and reliable sources of laser light and 25 W fiber coupled systems developed by Diomed have been in clinical use for over three years. For certain applications, particularly in the treatment of benign prostatic hyperplasia and flexible endoscopy, higher powers are desirable. In these applications the use of flexible optical fibers of no more than 600 micrometers core diameter is essential for compatibility with most commercial delivery fibers and instrumentation. A high power 60 W diode laser system for driving these small core fibers has been developed. The design requirements for medical applications are analyzed and system performance and results of use in gastroenterology and urology with small core fibers will be presented.

  20. Compact laser diode drivers for military rangefinder applications

    NASA Astrophysics Data System (ADS)

    Giorgi, D.; Philippbar, J.

    2010-04-01

    Compact and high current laser diode drivers for pumping solid-state lasers have been developed and tested. Designed to operate from a single DL123 battery or equivalent, the OptiSwitch PLDD-150-1-1 delivers 150 A of peak current for 300 μs to a laser diode bar at a 1 Hz repetition rate. Measuring only 2.1 × 0.75 × 0.78 inches and weighing 15.2 g, the unit is suited for man-portable target designation, rangefinding, illumination, and remote sensing applications. This paper will discuss the design philosophy behind this class of drivers which offer peak currents up to 200 A plus lifetime testing of eight drivers all operating at elevated input voltage and temperature at 4.5 Hz for 10M shots without a single failure or degradation in performance. Lastly, temperature testing down to -40 degC will be discussed.

  1. Utilization of pulsed diode lasers to lidar remote sensing

    NASA Astrophysics Data System (ADS)

    Penchev, S.; Pencheva, Vasilka H.; Naboko, Vassily N.; Naboko, Sergei V.; Simeonov, P.

    2001-04-01

    Investigation of new aspects of application of pulsed quantum well (In)GaAs/AlGaAs diode lasers to atmospheric spectroscopy and lidar remote sensing is reported. The presented method utilizing these powerful multichipstack diode lasers of broad radiation line is approved theoretically and experimentally for monitoring of atmospheric humidity. Molecular absorption of gas species in the investigated spectral band 0.85 - 0.9 micrometer implemented by laser technology initiates further development of prospective DIAL analysis. A mobile lidar system is realized, employing optimal photodetection based on computer-operated boxcar and adaptive digital filter processing of the lidar signal in the analytical system. Aerosol profile exhibiting cloud strata in open atmosphere by testing of the sensor is demonstrative of the efficiency and high sensitivity of long-range sounding.

  2. High current, high bandwidth laser diode current driver

    NASA Technical Reports Server (NTRS)

    Copeland, David J.; Zimmerman, Robert K., Jr.

    1991-01-01

    A laser diode current driver has been developed for free space laser communications. The driver provides 300 mA peak modulation current and exhibits an optical risetime of less than 400 ps. The current and optical pulses are well behaved and show minimal ringing. The driver is well suited for QPPM modulation at data rates up to 440 Mbit/s. Much previous work has championed current steering circuits; in contrast, the present driver is a single-ended on/off switch. This results in twice the power efficiency as a current steering driver. The driver electrical efficiency for QPPM data is 34 percent. The high speed switch is realized with a Ku-band GaAsFET transistor, with a suitable pre-drive circuit, on a hybrid microcircuit adjacent to the laser diode.

  3. Research and development for improved lead-salt diode lasers

    NASA Technical Reports Server (NTRS)

    Butler, J. F.

    1976-01-01

    A substantial increase in output power levels for lead-salt diode lasers, through the development of improved fabrication methods, as demonstrated. The goal of 1 mW of CW, single-mode, single-ended power output, was achieved, with exceptional devices exhibiting values greater than 8 mW. It was found that the current tuning rate could be controlled by adjusting the p-n junction depth, allowing the tuning rate to be optimized for particular applications. An unexpected phenomenon was encountered when crystal composition was observed to be significantly altered by annealing at temperatures as low as 600 C; the composition was changed by transport of material through the vapor phase. This effect caused problems in obtaining diode lasers with the desired operating characteristics. It was discovered that the present packaging method introduces gross damaging effects in the laser crystal through pressure applied by the C-bend.

  4. Electrical and optical study of semiconductor laser diodes and materials

    NASA Technical Reports Server (NTRS)

    Albin, Sacharia

    1987-01-01

    The characterization of a 2-D diode laser array from McDonald Douglas has been completed. The array consisted of 8 linear arrays of approximately 11 mm x 0.18 mm. Each array has between 7 and 8 diodes per mm. The threshold current is approximately 15 amps. The power output vs drive current (above threshold) of the array was measured. A peak power of 50 W was obtained at a drive current of 26 amps. Its far field pattern has a double lobe.

  5. Quantity change in collagen following 830-nm diode laser welding

    NASA Astrophysics Data System (ADS)

    Tang, Jing; O'Callaghan, David; Rouy, Simone; Godlewski, Guilhem; Prudhomme, Michel

    1996-12-01

    The actual mechanism for production of laser welding of tissue is presently unknown, but collagen plays an important role is tissue welded after laser irradiance. The quantity change in collagen extracted from the abdominal aorta of Wistar rats after tissue welding using an 830 nm diode laser was investigated. The collagen contents following repeated pepsin digestion after acetic acid extraction were determined with Sircol collagen assay. Compared with untreated aorta, the collagen content of the treated vessel was obvious decreased immediately after laser irradiation and following an initial increase on day 3, there was a peak at day 10. The results suggest that a part of collagen molecules is denatured by the heat of laser. There is an effect of stimulating collagen synthesis after laser welding with parameters used in this study.

  6. Thermally tunable integrated planar Bragg-grating stabilized diode laser

    NASA Astrophysics Data System (ADS)

    Lynch, S. G.; Gates, J. C.; Berry, S. A.; Holmes, C.; Smith, P. G. R.

    2015-03-01

    A pair of external cavity diode lasers are fabricated using an integrated planar Bragg grating. The planar waveguide and Bragg reflector is UV-written within a glass-on-silicon chip. Intensity isolated, continuous wavelength tuning at > 1kHz modulation rate is acheived using micro-heating elements fabricated directly over the Bragg grating. Low RIN (<140dB) and low linewidth (δν ~ 200 kHz) operation is found using a heterodyne measurement. We demonstrate the lasers operating in phase-locked loop configuration where one laser is frequency-offset locked to the other.

  7. Polarization control in ridge-waveguide-laser diodes

    SciTech Connect

    Amann, M.

    1987-04-20

    The polarization dependence of the gain/current relation and threshold current of quasi-index-guided laser diodes is analyzed for the case of lambda = 1.3 ..mu..m InGaAsP-InP ridge-waveguide lasers. Thereby it is shown that three different regimes for the stripe width and the lateral effective index discontinuity can be distinguished where one modal polarization (TE or TM) predominates. The significance of this finding on laser design and polarization control is discussed, and a comparison is performed on experimental results.

  8. Infrared laser diode with visible illuminator for biomedical stimulation

    NASA Astrophysics Data System (ADS)

    Strek, Wieslaw; Podbielska, Halina; Szafranski, C.; Kuzmin, Andrei N.; Ges, J. A.; Ryabtsev, Gennadii I.

    1995-02-01

    The special laser diode device (LDD) leasing in the near infrared region (IR) with two wavelengths: (lambda) 1 equals 850 nm and (lambda) 2 equals 1000 nm, designed for laser therapy, is presented. This device is characterized by a unique feature, namely a separate built-in illuminator, operating in 670 nm. The special construction of LDD and the illuminator enables the user to visualize exactly the surface irradiated by IR radiation. The exposure time and the output of laser power are also controlled and can be displayed on the LED monitor at the front panel. This new device, described here, is compact, low cost, and user friendly.

  9. Treatment of Gingival Hyperpigmentation by Diode Laser for Esthetical Purposes

    PubMed Central

    El Shenawy, Hanaa M.; Nasry, Sherine A.; Zaky, Ahmed A.; Quriba, Mohamed A. A.

    2015-01-01

    BACKGROUND: Gingival hyperpigmentation is a common esthetical concern in patients with gummy smile or excessive gingival display. Laser ablation has been recognized recently as the most effective, pleasant and reliable technique. It has the advantage of easy handling, short treatment time, hemostasis, decontamination, and sterilization effect. AIM: In the present study we wanted to explore the efficacy of a 980 nm wavelength diode laser in gingival depigmentation clinically by using both VAS and digital imaging method as means of assessment. METHODS: Diode laser ablation was done for 15 patients who requested cosmetic therapy for melanin pigmented gums. The laser beam delivered by fiberoptic with a diameter of 320 µm, the diode laser system has 980 nm wave lengths and 3 W irradiation powers, in a continuous contact mode in all cases, the entire surface of each pigmented maxillary and mandibular gingiva that required treatment was irradiated in a single session. Clinical examination and digital image analysis were done and the patients were followed up for 3 successive months. RESULTS: There was a statistically significant change in prevalence of bleeding after treatment, as none of the cases showed any signs of bleeding 1 week, 1 month and 3 months after ablation. No statistically significant change was observed in the prevalence of swelling after treatment The VAS evaluation demonstrated that only 4 patients complained of mild pain immediately after the procedure. No pain was perceived from the patients in the rest of the follow up period. There was no statistically significant change in prevalence of pain immediately after treatment compared to pain during treatment. There was a decrease in cases with mild pain after 1 week, 1 month as well as 3 months compared to pain during treatment and immediately after treatment. CONCLUSION: Within the limitations of this study, the use of diode laser was shown to be a safe and effective treatment modality that provides

  10. Two-Pass, Diode-Pumped Nd:YAG Slab Laser Head

    NASA Technical Reports Server (NTRS)

    Coyle, D. Barry

    1992-01-01

    Neodymium/yttrium aluminum garnet (Nd:YAG) ring-laser head designed for compactness, simplicity, and increased efficiency for side pumping by diode lasers. Laser head includes two linear arrays of diode lasers, two fused-silica collimating rods, and Nd:YAG slab. Slab mounted on finned copper block, providing good thermal dissipation.

  11. Finite element analysis of laser-diode heat emission and design of PI fuzzy cooling system

    NASA Astrophysics Data System (ADS)

    Yu, Fusheng; Shen, Xiaoqin; Leng, Changlin; Li, Zhi

    2005-01-01

    In order to realize the coupling of the crystal spectrum line, the wavelength output by the laser-diode must be adjusted to be accordant with the peak value absorbed by laser crystal in the solid laser of the laser-diode pump. In this paper, the finite element analysis (FEA) of the heat emission of the to-3 encapsulated laser-diode was researched and an accurate PI+Fuzzy temperature control system was developed. The refrigeration and the accurate temperature control of the high-power laser-diode was realized by the semiconductor refrigerator. Combined with fussy control and PI control, a full solid refrigerator of the laser-diode was developed. AT89C51 MCU and CRI[1] fussy control arithmetic were used in this system. So the system has high temperature control precision and little chatting. The rate of change of the optical power peak value output by the laser-diode was less than 1%.

  12. Integration of mode-locked diode lasers

    NASA Astrophysics Data System (ADS)

    Coleman, A. Catrina; Hou, Lianping; Marsh, John H.

    2016-03-01

    Monolithic mode-locked semiconductor lasers are attractive sources of short optical pulses with advantages over more conventional sources in compactness, robustness, performance stability, power consumption, and cost savings. The use of quantum well intermixing (QWI) to integrate passive sections and surface etched distributed Bragg reflectors (DBR) into monolithic laser cavity will be described. The performance of the devices will be presented.

  13. Diode laser: In treatment of recurrent verrucous leukoplakia

    PubMed Central

    Giri, Debanti; Agarwal, Nitin; Sinha, Abhishek; Srivastava, Sunita; Mishra, Anuj

    2016-01-01

    Laser first came into light in 1960 and had been used extensively in various fields of medicine. Laser has been experimented in the various dental field, and its utility is being recognized and established well in the dentistry. Lasers are widely used for a number of procedures such as cavity preparation, scaling, and root planning, surgical procedures like excision of soft tissue growths, etc., Improved healing, hemostasis, and sutureless excisions are some of the many advantages of laser over conventional treatment modalities. It is because of these advantages that laser is becoming more and more popular as a treatment option in various aspects of dentistry. We hereby present a case report, where we have used diode laser for surgical management of a proliferative verrucous leukoplakia (PVL), because of its many advantages over conventional methods. It presents very specific characteristics, mainly a more aggressive biological behavior than other forms of leukoplakia expressed by: A tendency toward multifocality (field cancerization); a high prospect of recurrence; and a high rate of malignant transformation, which can range between 40% and 100% in a follow-up period of 4.4–11.6 years. In this case, we evaluated the advantages of diode laser for the treatment of verrucous leukoplakia, where the results that we obtained were excellent. The patient had come for evaluation till the time of complete healing. PMID:27307679

  14. Diode laser: In treatment of recurrent verrucous leukoplakia.

    PubMed

    Giri, Debanti; Agarwal, Nitin; Sinha, Abhishek; Srivastava, Sunita; Mishra, Anuj

    2016-01-01

    Laser first came into light in 1960 and had been used extensively in various fields of medicine. Laser has been experimented in the various dental field, and its utility is being recognized and established well in the dentistry. Lasers are widely used for a number of procedures such as cavity preparation, scaling, and root planning, surgical procedures like excision of soft tissue growths, etc., Improved healing, hemostasis, and sutureless excisions are some of the many advantages of laser over conventional treatment modalities. It is because of these advantages that laser is becoming more and more popular as a treatment option in various aspects of dentistry. We hereby present a case report, where we have used diode laser for surgical management of a proliferative verrucous leukoplakia (PVL), because of its many advantages over conventional methods. It presents very specific characteristics, mainly a more aggressive biological behavior than other forms of leukoplakia expressed by: A tendency toward multifocality (field cancerization); a high prospect of recurrence; and a high rate of malignant transformation, which can range between 40% and 100% in a follow-up period of 4.4-11.6 years. In this case, we evaluated the advantages of diode laser for the treatment of verrucous leukoplakia, where the results that we obtained were excellent. The patient had come for evaluation till the time of complete healing. PMID:27307679

  15. Ruggedized microchannel-cooled laser diode array with self-aligned microlens

    DOEpatents

    Freitas, Barry L.; Skidmore, Jay A.

    2003-11-11

    A microchannel-cooled, optically corrected, laser diode array is fabricated by mounting laser diode bars onto Si surfaces. This approach allows for the highest thermal impedance, in a ruggedized, low-cost assembly that includes passive microlens attachment without the need for lens frames. The microlensed laser diode array is usable in all solid-state laser systems that require efficient, directional, narrow bandwidth, high optical power density pump sources.

  16. Diode Lasers used in Plastic Welding and Selective Laser Soldering - Applications and Products

    NASA Astrophysics Data System (ADS)

    Reinl, S.

    Aside from conventional welding methods, laser welding of plastics has established itself as a proven bonding method. The component-conserving and clean process offers numerous advantages and enables welding of sensitive assemblies in automotive, electronic, medical, human care, food packaging and consumer electronics markets. Diode lasers are established since years within plastic welding applications. Also, soft soldering using laser radiation is becoming more and more significant in the field of direct diode laser applications. Fast power controllability combined with a contactless temperature measurement to minimize thermal damage make the diode laser an ideal tool for this application. These advantages come in to full effect when soldering of increasingly small parts in temperature sensitive environments is necessary.

  17. Diode laser ignition of explosive and pyrotechnic components

    SciTech Connect

    Jungst, R.G.; Salas, F.J.

    1990-01-01

    The Laser Diode Ignition (LDI) program at Sandia Laboratories has as its objective the development of optically ignited analogs to the presently used low energy, hot wire igniters, DDT detonators, and actuators. In our concept, optical energy would be transmitted from a diode laser to the explosive or pyrotechnic power via a fiber optic. The laser energy is coupled to the energetic powder through a hermetically sealed optical feedthrough in the charge cavity. Optical ignition has many advantages, most of which are related to the removal of electrical leads to the powder interface. This eliminates concerns such as sensitivity to electrostatic discharge and electromagnetic radiation, conductance after fire, and isolation resistance. The optical interface would also not have the corrosion tendency that has occasionally been a problem with bridgewires. Another convenient property of diode laser sources is that the current and voltage needed to drive them are quite similar to those now applied to bridgewires for hot wire ignition. Therefore LDI devices would have an overall electrical requirement which is nearly identical to that of the hot wire components they are replacing.

  18. Extended ultrahigh-Q-cavity diode laser.

    PubMed

    Xie, Zhenda; Liang, Wei; Savchenkov, Anatoliy A; Lim, Jinkang; Burkhart, Jan; McDonald, Mickey; Zelevinsky, Tanya; Ilchenko, Vladimir S; Matsko, Andrey B; Maleki, Lute; Wong, Chee Wei

    2015-06-01

    We report on a study of a 698 nm extended cavity semiconductor laser with intracavity narrowband optical feedback from a whispering gallery mode resonator. This laser comprises an ultrahigh-Q (>10(10)) resonator supporting stimulated Rayleigh scattering, a diffraction grating wavelength preselector, and a reflective semiconductor amplifier. Single longitudinal mode lasing is characterized with sub-kilohertz linewidth and a 9 nm coarse tuning range. The laser has a potential application for integration with the 1S0-3P0 strontium transition to create compact precision atomic clocks. PMID:26030566

  19. Optomechanical design of the grating laser beam combiner (GLBC) laser diode header

    NASA Technical Reports Server (NTRS)

    Rall, Jonathan A. R.; Spadin, Paul L.

    1989-01-01

    A laser diode header has been fabricated for a grating laser beam combiner (GLBC). The laser diode header provides the thermal control, the drive electronics, and the optical system necessary for proper operation of the beam combiner. The diode header is required to provide diffraction limited optical performance while providing correction for worst case defocus aberration, 0.6 mrad excess divergence, and worst case decenter aberration, 1.0 mrad pointing error. The design of the header considered the mechanical design and the optical design together resulting in a small, self-contained header with 0.7 mrad range for focus correction and +/- 2.5 mrad of beam steering. The complete diode header is currently undergoing optical and mechanical performance testing.

  20. Progress in high-energy-class diode laser pump sources

    NASA Astrophysics Data System (ADS)

    Crump, P.; Frevert, C.; Bugge, F.; Knigge, S.; Erbert, G.; Tränkle, G.; Pietrzak, A.; Hüslewede, R.; Zorn, M.; Sebastian, J.; Lotz, J.; Fassbender, W.; Neukum, J.; Körner, J.; Hein, J.; Töpfer, T.

    2015-03-01

    A new generation of diode-pumped high-energy-class solid-state laser facilities is in development that generate multijoule pulse energies at around 10 Hz. Currently deployed quasi-continuous-wave (QCW) diode lasers deliver average inpulse pump powers of around 300 W per bar. Increased power-per-bar helps to reduce the system size, complexity and cost per Joule and the increased pump brilliance also enables more efficient operation of the solid state laser itself. It has been shown in recent studies, that optimized QCW diode laser bars centered at 940…980 nm can operate with an average in-pulse power of > 1000 W per bar, triple that of commercial sources. When operated at pulsed condition of 1 ms, 10 Hz, this corresponds to > 1 J/bar. We review here the status of these high-energy-class pump sources, showing how the highest powers are enabled by using long resonators (4…6 mm) for improved cooling and robustly passivated output facets for high reliability. Results are presented for prototype passively-cooled single bar assemblies and monolithic stacked QCW arrays. We confirm that 1 J/bar is sustained for fast-axis collimated stacks with a bar pitch of 1.7 mm, with narrow lateral far field angle (< 12° with 95% power) and spectral width (< 12 nm with 95% power). Such stacks are anticipated to enable Joule/bar pump densities to be used near-term in commercial high power diode laser systems. Finally, we briefly summarize the latest status of research into bars with higher efficiencies, including studies into operation at sub-zero temperatures (-70°C), which also enables higher powers and narrower far field and spectra.

  1. Packaging of hard solder 500W QCW diode laser array

    NASA Astrophysics Data System (ADS)

    Li, Xiaoning; Wang, Jingwei; Hou, Dong; Nie, Zhiqiang; Liu, Xingsheng

    2016-03-01

    The package structure critically influences the major characteristics of diode laser, such as thermal behavior, output power, wavelength and smile effect. In this work, a novel micro channel cooler (MCC) for stack array laser with good heat dissipation capability and high reliability is presented. Numerical simulations of thermal management with different MCC structure are conducted and analyzed. Based on this new MCC packaging structure, a series of QCW 500W high power laser arrays with hard solder packaging technology has been fabricated. The performances of the laser arrays are characterized. A narrow spectrum of 3.12 nm and an excellent smile value are obtained. The lifetime of the laser array is more than 1.38×109 shots and still ongoing.

  2. Frequency noise characterisation of narrow linewidth diode lasers

    NASA Astrophysics Data System (ADS)

    Turner, L. D.; Weber, K. P.; Hawthorn, C. J.; Scholten, R. E.

    2002-01-01

    We examine several approaches to laser frequency noise measurement in the frequency and time domains. Commonly employed methods such as optical frequency discrimination and the Allan variance are found to be complex, expensive, time-consuming, or incomplete. We describe a practical method of demodulating a laser beat note to measure a frequency noise spectrum, using a phase-locked loop frequency discriminator based on a single low-cost integrated circuit. This method measures the frequency noise spectrum of a laser directly and in detail and is insensitive to intensity fluctuations. The advantages of this scheme are demonstrated through measurement of the frequency noise spectrum for two external cavity diode lasers (ECDL), clearly distinguishing several common noise sources. These are isolated and removed, reducing the individual laser rms linewidth from 2 MHz to 450 kHz. The spectrum is used to calculate the Allan variance, which shows almost none of the important information.

  3. Diode-Pumped Dye Laser Using a Tapered Optical Fiber

    NASA Astrophysics Data System (ADS)

    Patterson, Brian; Stofel, James; Myers, Elliot; Knize, Randy

    2015-05-01

    We describe the construction of a simple dye laser based on a single-mode optical fiber. Light from a 120-mW laser diode (λ = 520 nm) is launched into the fiber. The fiber is tapered to a diameter of approximately 1 μm and placed in Rhodamine 6G laser dye. The pump light interacts with the gain medium through the evanescent field outside the fiber causing stimulated emission, which couples back into the fiber. Mirrors on each end of the fiber provide the necessary feedback for lasing, and a grating is used to narrow the spectral output. We characterize the lasing threshold and output spectrum of the laser. This has been a good project for undergraduate students to learn about lasers and optics.

  4. Preliminary experiences on diode laser welding of skin

    NASA Astrophysics Data System (ADS)

    Reali, Umberto M.; Borgognoni, L.; Martini, L.; Chiarugi, C.; Gori, F.; Pini, Roberto; Toncelli, F.; Vanni, U.

    1994-12-01

    Dye enhanced laser welding has been recently proposed for skin closures to exploit the advantages of laser procedure (possible reduction of scar formation, no inflammatory reaction). In this preliminary study we used the diode laser-assisted technique to perform welding of rats' skin. In the pilot phase of the study we investigated the effect of the interaction between diode laser radiation and 20 full thickness skin wounds, performed on the shaved backs of 10 Wistar rats, using laser power in the range of 200 - 150 mW and, as the photoenhancing chromophore, Indocyanine Cardio-green (ICG) dye saturated solution in plasma. Ten wounds were sutured with 4.0 nylon thread, to provide a comparison with the traditional procedure. Wounds' samples were explanted on day 3 and 7 after the treatment, for histological evaluation. Clinical examination on the same days showed a high percentage of wounds dehiscence and presence of scales and crusts. Histologic examination demonstrated evidence of thermal injury and a heightened inflammation, superior to that of suture closures. In the second phase of the study, a lower laser power (150 - 80 mW), ICG-plasma-non saturated solution (ICG-sol) and ICG-plasma-saturated-sodium hyaluronate gel (ICG-gel), were used. Six wounds were filled with ICG-sol and six with ICG-gel, then irradiated at 150, 120 and 80 mW. Postoperative explants were performed on day 3 and 7. Clinical and histological results from this group were satisfactory: we recorded only one case of dehiscence, well healed wounds, no epidermal necrosis and a mild inflammatory reaction, reduced respect to that of traditional closure. We characterized the optimum range of parameters of diode laser-assisted technique to achieve an effective skin welding and the corresponding clinical and histologic pattern was described.

  5. Compact, efficient, scalable neodymium laser co-doped with activator ions and pumped by visible laser diodes

    NASA Astrophysics Data System (ADS)

    Scheps, Richard

    1994-02-01

    Efficient, low threshold laser emission from a laser crystal doped with chromium and neodymium ions is obtained when pumped by visible laser diodes in the range of 610 nm to 680 nm. A typical laser Cr,Nd:GSGG crystal having an extraordinarily broad absorption bandwidth allows high pump efficiencies when using visible laser diodes, particularly in comparison to the Nd:YAG laser. The broad absorption bandwidth tolerance of the Cr,Nd:GSGG crystal to the pumping wavelengths allows visible diode pumping of the neodymium transition without regard to the wavelength of the visible diodes. Longitudinal or end-pumping to take advantage of the emission properties of the visible laser diodes, a nearly hemispherical laser resonator configuration and other co-doped Cr,Nd laser host materials are disclosed.

  6. Diode laser photocoagulation in PHACES syndrome hemangiomas: a case series

    NASA Astrophysics Data System (ADS)

    Romeo, U.; Russo, N.; Polimeni, A.; Favia, G.; Lacaita, M. G.; Limongelli, L.; Franco, S.

    2014-01-01

    PHACES syndrome is a pediatric syndrome with cutaneous and extra-cutaneous manifestations, such as Posterior fossa defects, Hemangiomas, Arterial lesions, Cardiac abnormalities/aortic coarctation, Eye abnormalities and Sternal cleft. Facial hemangiomas affect the 75% of patients and may arise on the oral mucosa or perioral cutaneous regions. In this study we treated 26 Intraoral Haemangiomas (IH) and 15 Perioral Haemangiomas (PH) with diode laser photocoagulation using a laser of 800+/-10nm of wavelength. For IH treatment an optical fiber of 320 μm was used, and the laser power was set ted at 4 W (t-on 200 ms / t-off 400ms; fluence: 995 J/cm2). For PH treatment an optical fiber of 400 μm at the power of 5 W was used (t-on 100 ms / t-off 300 ms; fluence: 398 J/cm2). IH healed after one session (31%), the other (69%) after two sessions of Laser therapy. In each session, only a limited area of the PH was treated, obtaining a progressive improvement of the lesion. Diode laser photocoagulation is an effective option of treatment for IH and PH in patients affected by PHACE because of its minimal invasiveness. Moreover laser photocoagulation doesn't have side effects and can be performed repeatedly without cumulative toxicity. Nevertheless, more studies are required to evaluate the effectiveness of the therapy in mid and long time period.

  7. Highly reliable contacts for lead-salt diode lasers

    NASA Astrophysics Data System (ADS)

    Lo, W.

    1981-02-01

    In order to improve the long term reliability of lead-salt diode lasers, ohmic contacts of multilayer, thin-film structures consisting of In plus Au, Pt, Ni, and Pd have been studied. Diode lasers of PbSnTe fabricated with a variety of contacts were tested during room-temperature storage and during accelerated aging tests. The results show that contact reliability can be improved when multiple overlapping films are used. After 4500 h of baking at 60 C, lasers with In-Au-Pd-Au contacts on both sides showed the least resistance increase (10%). For lasers with In-Au-Pt-Au contacts, 1 h of baking at 60 C is equivalent to 2 d storage at room temperature. Extrapolating these results, a 70% increase in contact resistance is expected for this type of laser after 9000 d of storage at room temperature. The data also suggests that a smaller increase in contact resistance can be expected for lasers fabricated with In-Au-Ni and In-Au-Pd-Au contacts.

  8. High power, high efficiency diode pumped Raman fiber laser

    NASA Astrophysics Data System (ADS)

    Glick, Yaakov; Fromzel, Viktor; Zhang, Jun; Dahan, Asaf; Ter-Gabrielyan, Nikolay; Pattnaik, Radha K.; Dubinskii, Mark

    2016-06-01

    We demonstrate a high power high efficiency Raman fiber laser pumped directly by a laser diode module at 976 nm. 80 Watts of CW power were obtained at a wavelength of 1020 nm with an optical-to-optical efficiency of 53%. When working quasi-CW, at a duty cycle of 30%, 85 W of peak power was produced with an efficiency of 60%. A commercial graded-index (GRIN) core fiber acts as the Raman fiber in a power oscillator configuration, which includes spectral selection to prevent generation of the 2nd Stokes. In addition, significant brightness enhancement of the pump beam is attained due to the Raman gain distribution profile in the GRIN fiber. To the best of our knowledge, this is the highest power Raman fiber laser directly pumped by laser diodes, which also exhibits a record efficiency for such a laser. In addition, it is the highest power Raman fiber laser (regardless of pumping source) demonstrated based on a GRIN fiber.

  9. Polarization competition in quasi-index-guided laser diodes

    SciTech Connect

    Amann, M.; Stegmueller, B.

    1988-03-15

    The mechanism of polarization competition in laser diodes with a lateral quasi-index-guiding (QIG) structure is analyzed generally by way of the effective index approximation using a simplified QIG laser model. The influence of the relevant waveguide parameters on the polarization-dependent threshold current of QIG laser diodes is investigated in detail by example of lambda = 1.3-..mu..m ridge-waveguide lasers. Thereby, it is found that for intermediate values of the effective index step, the TM mode exhibits a higher gain and lower threshold current, whereas for pure gain guiding or strong index guiding, the TE mode prevails. This behavior, which compares excellently to published experimental results, is proven as a basic feature of the two-dimensional waveguiding mechanism in QIG devices. Accordingly, the effect of stress-induced anisotropy of the optical gain has been found to be of minor importance as the origin for TM-polarized QIG lasers made from lattice-matched heterostructures. It is further demonstrated that, for certain device parameters, the QIG lasers with a small effective index step exhibit somewhat higher threshold currents than the purely gain-guided devices of identical geometry.

  10. 980nm diode laser pump modules operating at high temperature

    NASA Astrophysics Data System (ADS)

    Campbell, Jenna; Semenic, Tadej; Leisher, Paul; Bhunia, Avijit; Mashanovitch, Milan; Renner, Daniel

    2016-03-01

    Existing thermal management technologies for diode laser pumps place a significant load on the size, weight and power consumption of High Power Solid State and Fiber Laser systems, thus making current laser systems very large, heavy, and inefficient in many important practical applications. This problem is being addressed by the team formed by Freedom Photonics and Teledyne Scientific through the development of novel high power laser chip array architectures that can operate with high efficiency when cooled with coolants at temperatures higher than 50 degrees Celsius and also the development of an advanced thermal management system for efficient heat extraction from the laser chip array. This paper will present experimental results for the optical, electrical and thermal characteristics of 980 nm diode laser pump modules operating effectively with liquid coolant at temperatures above 50 degrees Celsius, showing a very small change in performance as the operating temperature increases from 20 to 50 degrees Celsius. These pump modules can achieve output power of many Watts per array lasing element with an operating Wall-Plug-Efficiency (WPE) of >55% at elevated coolant temperatures. The paper will also discuss the technical approach that has enabled this high level of pump module performance and opportunities for further improvement.

  11. Diode laser vaporisation of the prostate vs. diode laser under cold irrigation: A randomised control trial

    PubMed Central

    Pillai, Ravisankar G.; Al Naieb, Ziad; Angamuthu, Stephen; Mundackal, Tintu

    2014-01-01

    Objective To compare the perioperative morbidity and early follow-up after diode laser vaporisation of the prostate (LVP) and its modification, diode laser under cold irrigation (LUCI) in patients with symptomatic benign prostatic hyperplasia, as the main disadvantages of LVP are the postoperative pain, dysuria and storage urinary symptoms. Patients and methods This was a single-centre prospective randomised control trial in which 100 patients were randomised to receive LVP (50) or LUCI (50) from June 2011 until July 2012. LUCI is similar to LVP except that it is done under normal irrigation with saline at 4 °C instead of saline at room temperature. The primary outcome measures were the International Prostate Symptom Score (IPSS), IPSS-Dysuria, a pain scale (PS), maximum flow rate (Qmax), a quality-of-life (QoL) score and the postvoid residual urine volume (PVR) after 1 month, then the IPSS, Qmax, QoL, and PVR at 3 and 12 months. Secondary outcomes included intraoperative surgical variables, e.g., the decline in core temperature, bleeding, peri- and postoperative morbidity. Results The baseline characteristics of both groups were similar. For the primary outcome measures, there was a statistically significant difference between the groups in all variables except Qmax after 1 month, in favour of LUCI. The mean (SD) IPSS at 1 month in the LVP group was 8.97 (1.68), statistically significantly different from that after LUCI, of 6.89 (1.5) (P < 0.05). The mean IPSS-Dysuria at 1 month was also significantly, at −2.32 (0.91) for LVP and 3.54 (1.07) for LUCI (P < 0.05). The respective mean PS at 1 month was 7.84 (2.92) and 5.7 (2.1) (P < 0.05). The QoL and PVR at 1 month were also significantly different. Within the first month 17% of patients in the LVP group and 4% in the LUCI group complained of transient urgency or stress incontinence, and this difference was statistically significant (P < 0.05). There was no significant bleeding in either group

  12. Optimization of beam transformation system for laser-diode bars.

    PubMed

    Yu, Junhong; Guo, Linhui; Wu, Hualing; Wang, Zhao; Gao, Songxin; Wu, Deyong

    2016-08-22

    An optimized beam transformation system (BTS) is proposed to improve the beam quality of laser-diode bars. Through this optimized design, the deterioration of beam quality after the BTS can be significantly reduced. Both the simulation and experimental results demonstrate that the optimized system enables the beam quality of a mini-bar (9 emitters) approximately equal to 5.0 mm × 3.6 mrad in the fast-axis and slow-axis. After beam shaping by the optimized BTS, the laser-diode beam can be coupled into a 100 μm core, 0.15 numerical aperture (NA) fiber with an output power of over 100 W and an electric-optical efficiency of 46.8%. PMID:27557249

  13. Laser diode self-mixing technique for liquid velocimetry

    NASA Astrophysics Data System (ADS)

    Alexandrova, A.; Welsch, C. P.

    2016-09-01

    Using the self-mixing technique, or optical feedback interferometry, fluid velocity measurements of water seeded with titanium dioxide have been performed using a laser diode to measure the effect of the seeding particle concentration and also the pump speed of the flow. The velocimeter utilises commercially available laser diodes with a built-in photodiode for detection of the self-mixing effect. The device has demonstrated an accuracy better than 10% for liquid flow velocities up to 1.5 m/s with a concentration of scattering particles in the range of 0.8-0.03%. This is an improvement of one order of magnitude compared to previous experiments. The proposed velocimeter is to be developed further for application in gas-jet measurements.

  14. Diode laser contact transscleral retinal photocoagulation: a clinical study.

    PubMed Central

    McHugh, D A; Schwartz, S; Dowler, J G; Ulbig, M; Blach, R K; Hamilton, P A

    1995-01-01

    AIM--To examine the clinical efficacy of contact transscleral retinal photocoagulation with a diode laser. METHODS--Transscleral retinal photocoagulation was performed on 36 eyes. The conditions treated included peripheral retinal breaks associated with retinal detachments (30 eyes) and giant retinal tears (six eyes). Of the 30 eyes with retinal detachments, 28 underwent transscleral photocoagulation to the site of drainage of subretinal fluid in an attempt to reduce the risk of hemorrhage. RESULTS--Threshold lesions were obtained with irradiances of between 95.4 W/cm2 and 191 W/cm2. Satisfactory chorioretinal adhesion was achieved in all eyes with retinal breaks and giant retinal tears. The only significant complications of treatment encountered were punctate choroidal haemorrhages (three eyes). Drainage related choroidal haemorrhage following earlier photocoagulation occurred in two of 28 eyes. CONCLUSIONS--This study confirms the clinical potential of transscleral diode laser photocoagulation in the therapy of surgical retinal conditions. Images PMID:8562540

  15. Airborne tunable diode laser measurements of trace atmospheric gases

    NASA Astrophysics Data System (ADS)

    Fried, Alan; Wert, Bryan P.; Henry, Bruce E.; Drummond, James R.

    1998-05-01

    Highly sensitive and accurate measurements of numerous trace gases are required to further our understanding of atmospheric processes. Tunable diode laser systems, which offer many advantages in this regard, can be designed for reliable field measurements on both ground-based and aircraft platforms. The present paper describes the long term effort at the National Center for Atmospheric Research (NCAR) to develop, employ, and validate a highly sensitive tunable diode laser absorption spectrometer for the measurement of various trace gases, including formaldehyde and carbon monoxide. This system was successfully employed on three recent aircraft campaigns. The present paper describes the aircraft instrument along with hardware and software features incorporated for high sensitivity, with particular emphasis on major modifications to the NCAR aircraft system over the past year.

  16. Laser-diode-based joint transform correlator for fingerprint identification

    NASA Astrophysics Data System (ADS)

    Lal, Amit K.; Zang, De Yu; Millerd, James E.

    1999-01-01

    A laser-diode-based joint transform correlator (JTC) is reported here for the identification and discrimination of fingerprints. The system employs compact and inexpensive laser diodes as the light sources and a bacteriorhodopsin (BR) film in the Fourier plane, which can record the joint power spectrum without the need for expensive spatial light modulators or CCD cameras. The BR film also introduces nonlinearities in the Fourier plane which can improve JTC performance. In addition, real-time, all-optical programmable spatial filtering is demonstrated to improve the discrimination of the system. We present computer modeling and experimental results of this optical correlator, which shows excellent potential for the identification and discrimination of fingerprints.

  17. Diode laser for excisional biopsy of peripheral ossifying fibroma

    PubMed Central

    Chawla, Kirti; Lamba, Arundeep Kaur; Faraz, Farrukh; Tandon, Shruti; Ahad, Abdul

    2014-01-01

    Peripheral Ossifying Fibroma is one of the commonest occurring reactive lesions on gingiva. It is associated with local irritational factors and often interferes with speech, mastication and maintenance of oral hygiene, in addition to being aesthetically unpleasant. It is usually treated with surgical excision using scalpel and removal of irritational factors, often resulting in mucogingival defect. Other modalities such as radiosurgery and electrocautery have also been used for its management, but they cause changes in microarchitecture of biopsy specimen, altering the histologic picture for true diagnosis. We are presenting a case of excisional biopsy of this lesion in an adult female using a diode laser with excellent post-operative results, without affecting microarchitecture of biopsy specimen. The patient is being followed for last 1 year and no sign of recurrence has been found. A diode laser may offer a good alternative modality for management of such cases. PMID:25225570

  18. Diode laser based water vapor DIAL using modulated pulse technique

    NASA Astrophysics Data System (ADS)

    Pham, Phong Le Hoai; Abo, Makoto

    2014-11-01

    In this paper, we propose a diode laser based differential absorption lidar (DIAL) for measuring lower-tropospheric water vapor profile using the modulated pulse technique. The transmitter is based on single-mode diode laser and tapered semiconductor optical amplifier with a peak power of 10W around 800nm absorption band, and the receiver telescope diameter is 35cm. The selected wavelengths are compared to referenced wavelengths in terms of random error and systematic errors. The key component of modulated pulse technique, a macropulse, is generated with a repetition rate of 10 kHz, and the modulation within the macropulse is coded according to a pseudorandom sequence with 100ns chip width. As a result, we evaluate both single pulse modulation and pseudorandom coded pulse modulation technique. The water vapor profiles conducted from these modulation techniques are compared to the real observation data in summer in Japan.

  19. Measuring Young's modulus using a self-mixing laser diode

    NASA Astrophysics Data System (ADS)

    Lin, Ke; Yu, Yanguang; Xi, Jiangtao; Fan, Yuanlong; Li, Huijun

    2014-03-01

    This paper presents a novel approach for determining the Young's modulus by using a self-mixing laser diode (SMLD). An SMLD system consists of a laser diode (LD), a microlens and an external target. With a small portion of light backscatterd or reflected by the target re-entering the LD inside cavity, both the amplitude and frequency of the LD power are modulated. This modulated LD power is referred as a self-mixing signal (SMS) which is detected by the photodiode (PD) packaged in the rear of the LD. The external target is the tested sample which is in damping vibration excited by a singular elastic strike with an impulse tool. The vibration information from the tested sample is carried in the SMS. Advanced data processing in frequency-domain is applied on the SMS, from which the resonant frequency of the vibration can be retrieved, and hence Young's modulus is calculated. The proposed method has been verified by simulations.

  20. Tunable diode laser spectroscopy as a technique for combustion diagnostics

    NASA Astrophysics Data System (ADS)

    Bolshov, M. A.; Kuritsyn, Yu. A.; Romanovskii, Yu. V.

    2015-04-01

    Tunable diode laser absorption spectroscopy (TDLAS) has become a proven method of rapid gas diagnostics. In the present review an overview of the state of the art of TDL-based sensors and their applications for measurements of temperature, pressure, and species concentrations of gas components in harsh environments is given. In particular, the contemporary tunable diode laser systems, various methods of absorption detection (direct absorption measurements, wavelength modulation based phase sensitive detection), and relevant algorithms for data processing that improve accuracy and accelerate the diagnostics cycle are discussed in detail. The paper demonstrates how the recent developments of these methods and algorithms made it possible to extend the functionality of TDLAS in the tomographic imaging of combustion processes. Some prominent examples of applications of TDL-based sensors in a wide range of practical combustion aggregates, including scramjet engines and facilities, internal combustion engines, pulse detonation combustors, and coal gasifiers, are given in the final part of the review.

  1. Use of laser diodes in cavity ring-down spectroscopy

    SciTech Connect

    Zare, R.N.; Paldus, B.A.; Ma, Y.; Xie, J.

    1997-12-31

    We have demonstrated that cavity ring-down spectroscopy (CRDS), a highly sensitive absorption technique, is versatile enough to serve as a complete diagnostic for materials process control. In particular, we have used CRDS in the ultraviolet to determine the concentration profile of methyl radicals in a hot-filament diamond reactor; we have applied CRDS in the mid-infrared to detect 50 ppb of methane in a N{sub 2} environment; and, we have extended CRDS so that we can use continuous-wave diode laser sources. Using a laser diode at 810 nm, we were able to achieve a sensitivity of 2 x 10{sup -8} cm{sup -1}. Thus, CRDS can be used not only as an in situ diagnostic for investigating the chemistry of diamond film deposition, but it can also be used as a gas purity diagnostic for any chemical vapor deposition system.

  2. V-shaped resonators for addition of broad-area laser diode arrays

    DOEpatents

    Liu, Bo; Liu, Yun; Braiman, Yehuda Y.

    2012-12-25

    A system and method for addition of broad-area semiconductor laser diode arrays are described. The system can include an array of laser diodes, a V-shaped external cavity, and grating systems to provide feedback for phase-locking of the laser diode array. A V-shaped mirror used to couple the laser diode emissions along two optical paths can be a V-shaped prism mirror, a V-shaped stepped mirror or include multiple V-shaped micro-mirrors. The V-shaped external cavity can be a ring cavity. The system can include an external injection laser to further improve coherence and phase-locking.

  3. ND laser with co-doped ion(s) pumped by visible laser diodes

    NASA Astrophysics Data System (ADS)

    Scheps, Richard

    1993-04-01

    The 1.06 microns Nd transition in a co-doped Cr,Nd:Gd3Sc2Ga3O12 (Cr,Nd:GSGG) gain element is obtained by diode pumping Cr(3+) at 670 run and produces efficient, low threshold laser operation. Although co-doped Cr,Nd:GSGG was developed for more efficient flashlamp pumping, it has the desirable property of having an extraordinarily broad absorption to allow for efficient diode pumping relative to the ND:YAG laser. The consequent broad bandwidth tolerance of the Cr,Nd:GSGG for the diode pumping radiation allows diode pumping of the 1.06 microns transition without regard to the wavelength of the visible diodes which has the potential for reducing the cost of the semiconductor pump and also demonstrates the extended versatility of these diodes which previously had been restricted to pump the Cr(3+) tunable vibronic lasers. CW and long pulse diode pumping provided pump power levels as high as 300 mW CW and 1 W pulsed. The lowest threshold power was measured at 938 micron W and the highest output power was obtained at 43 mW CW and 173 mW pulsed. The best slope efficiency obtained was 42.1%, 78% of the theoretical maximum. Loss measurements indicate a value of 0.4%/cm.

  4. Optimization of rod diameter in solid state lasers side pumped with multiple laser diode arrays

    NASA Technical Reports Server (NTRS)

    Sims, Newton, Jr.; Chamblee, Christyl M.; Barnes, Norman P.; Lockard, George E.; Cross, Patricia L.

    1992-01-01

    Results of a study to determine the optimum laser rod diameter for maximum output energy in a solid state neodymium laser transversely pumped with multiple laser diode arrays are reported here. Experiments were performed with 1.0 mm, 1.5 mm and 2.0 mm rod radii of both neodymium doped Y3Al5O12 (Nd:YAG) and La2Be2O5 (Nd:BeL) pumped with laser diode arrays having a maximum combined energy of 10.5 mJ. Equations were derived which predict the optimum rod radius and corresponding output mirror reflectivity for a given laser material and total pump energy. Predictions of the equations agreed well with the experiments for each of the laser materials which possessed significantly different laser properties from one another.

  5. Suppression of beam steering in an injection-locked laser diode array

    SciTech Connect

    Brewer, L.R. )

    1991-12-09

    Experimental measurements were made to demonstrate that the degree of beam steering in an injection-locked laser diode array is related to the divergence of the master laser beam. For a collimated master laser beam the beam steering was suppressed. The injection-locked laser diode array beam steers with the master laser wavelength because only a portion of the divergent master laser beam satisfies the round trip mode condition.

  6. Diode-pumped Nd:YAG laser for precision laser machining

    SciTech Connect

    Machan, J.; Valley, M.; Holleman, G.; Mitchell, M.; Burchman, D.; Zamel, J.; Harpole, G.; Injeyan, H.; Marabella, L.

    1996-10-01

    Results are presented on a high power, diode-pumped, pulsed Nd:YAG laser for precision laser machining. The laser is an unstable resonator with a graded reflectivity outcouplers, generating a beam with excellent beam quality. The gain medium is a single zig-zag slab, pumped symmetrically by diode arrays. The use of diode arrays minimizes the thermal loading on the slab, and the zig-zag path averages thermal distortions in the zig-zag dimension. Measurements of beam divergence as a function of diode duty-cycle will be presented. Available pulse formats will also be discussed. To date, the laser has produced 720 W at 20% diode duty-cycle with a stable cavity and 550 W at 20% duty cycle with an unstable cavity in close agreement with model predictions. The beam divergence has been measured to be 1.7 times diffraction-limited at 20% duty cycle. The laser has been operated with pulse lengths from 20 {micro}s to 1 ms and is being used to obtain laser processing data, with some results shown.

  7. Analysis of steady-state characteristics of bistable laser diodes

    SciTech Connect

    Zhong Lichen; Guo Yili

    1987-05-01

    In this paper we analyze the steady-state characteristics of bistable semiconductor laser diode (BILD). A simple model for optical output of BILD is obtained using nonlinear rate equations for electron and photon densities. This model emphasizes the physical mechanisms and parameters responsible for the bistability, gives the state equation and explains the main features of BILD. Bistability with a very large hysteresis in P/sub 0/-P/sub 4/ characteristics is a distinctive feature of BILD.

  8. Passively cooled diode laser for high-power applications

    NASA Astrophysics Data System (ADS)

    Bonati, Guido F.; Hennig, Petra; Schmidt, Karsten

    2004-06-01

    For the usage of diode lasers in industrial applications, customers ask today for expected lifetimes of more then 30.000 hours. To match the request for low costs per Watt as well, the output power has to be as high as possible. To achieve a maximum power out of a diode laser bar, heat removal must be extremely efficient. Today, micro channel heatsinks (MCHS) are the only way to achieve the high power level of 50W. But due to erosion/corrosion effects the lifetime of MCHS is limited at 15000...20.000 hours today. Finally we have to determine that for selected semiconductor materials not the semiconductor but the heatsink is limiting the expected lifetime of high power diode lasers today. Passive heat sinks based on solid copper are not limiting lifetime expectations in any way. But as cooling efficiency is lower, the power has to be reduced to a level of 30...40W. The first time ever, the JENOPTIK Laserdiode can present today a cooling technique that combines the passive cooling of a diode laser bar with the optical output a power of a bar, mounted on a MCHS. Using a special heat exchanger called DCB (patent pending) we were able to increase the power to 50W per bar while looking forward to extend the expected lifetime to more than 30.000 hours for selected materials. Restrictions on the quality of the water by means of deionization grade or PH- level are no longer necessary. The device is operating with regular water. The flow rate is as low as on MCHS, the pressure drop over the DCB is comparable. Additionally, the measurements will show an even lower thermal resistance compared to MCHS. The second generationof engineering samples is built up for pumping rows. A vertical stack design will be available for evaluating purposes soon. All these efforts are part of the JENOPTIK Laserdiode's LongLifeTechnology.

  9. Computer holography by means of the laser diodes

    NASA Astrophysics Data System (ADS)

    Borodin, Arthur N.; Ilchenko, Volodymyr; Malov, Alexander N.; Sychevskiy, Alexey V.

    2007-02-01

    A computer holography is the optical hologram recording on the CCD-matrix with digital reconstruction of the 2Dimages for the different volume object cross-sections. The possibility to use compact semiconductor laser diodes in the computer holography for 3D-scene registration is experimentally proved in the D. Gabor's scheme. For off axis hologram recording the S. Benton's scheme for holography using is suggested.

  10. Monolithically Peltier-cooled laser diodes

    SciTech Connect

    Hava, S.; Hunsperger, R.G.; Sequeira, H.B.

    1984-04-01

    A new method of cooling a GaAs/GaAlAs laser in an optical integrated circuit or on a discrete chip, by adding an integral thermoelectric (Peltier) cooling and heat spreading device to the laser, is presented. This cooling both reduces and stabilizes the laser junction temperature to minimize such deleterious effects as wavelength drift due to heating. A unified description of the electrical and thermal properties of a monolithic semiconductor mesa structure is given. Here it is shown that an improvement in thermal characteristics is obtained by depositing a relatively thick metallic layer, and by using this layer as a part of an active Peltier structure. Experimental results reveal a 14-percent increase in emitted power (external quantum efficiency) due to passive heat spreading and a further 8-percent if its Peltier cooler is operated. Fabrication techniques used to obtain devices exhibiting the above performance characteristics are given. 21 references.

  11. DFB laser diode operation at 77 K

    NASA Astrophysics Data System (ADS)

    Hopkinson, D. A.; Cornish, S. L.; Edwards, N. H.; Baird, P. E. G.; Cockburn, A.; Cameron, K.

    1996-05-01

    The low-temperature operation of distributed feedback semiconductor lasers in the vicinity of 0957-0233/7/5/011/img9 is investigated. The room temperature properties of a sample DFB laser are given and its power and frequency characteristics at 77 K are compared. In this way, the linearity of the temperature against frequency relation down to liquid nitrogen temperature is confirmed and a reduction in the threshold current to near zero is also shown. For spectroscopic purposes, it was found that stabilization of the laser temperature at 77 K is possible to within 50 mK over a range of about 77 - 87 K. This corresponds to a frequency change of about 120 GHz. The Schawlow - Townes relation predicts a reduction in linewidth with temperature; some evidence for this is given.

  12. The study of laser beam riding guided system based on 980nm diode laser

    NASA Astrophysics Data System (ADS)

    Qu, Zhou; Xu, Haifeng; Sui, Xin; Yang, Kun

    2015-10-01

    With the development of science and technology, precision-strike weapons has been considered to be important for winning victory in military field. Laser guidance is a major method to execute precision-strike in modern warfare. At present, the problems of primary stage of Laser guidance has been solved with endeavors of countries. Several technical aspects of laser-beam riding guided system have been mature, such as atmosphere penetration of laser beam, clutter inhibition on ground, laser irradiator, encoding and decoding of laser beam. Further, laser beam quality, equal output power and atmospheric transmission properties are qualified for warfare situation. Riding guidance instrument is a crucial element of Laser-beam riding guided system, and is also a vital element of airborne, vehicle-mounted and individual weapon. The optical system mainly consist of sighting module and laser-beam guided module. Photoelectric detector is the most important sensing device of seeker, and also the key to acquire the coordinate information of target space. Currently, in consideration of the 1.06 u m of wavelength applied in all the semi-active laser guided weapons systems, lithium drifting silicon photodiode which is sensitive to 1.06 u m of wavelength is used in photoelectric detector. Compared to Solid and gas laser, diode laser has many merits such as small volume, simple construction, light weight, long life, low lost and easy modulation. This article introduced the composition and operating principle of Laser-beam riding guided system based on 980 nm diode laser, and made a analysis of key technology; for instance, laser irradiator, modulating disk of component, laser zooming system. Through the use of laser diode, Laser-beam riding guided system is likely to have smaller shape and very light.

  13. Broadly tunable, longitudinally diode-pumped Alexandrite laser

    NASA Astrophysics Data System (ADS)

    Strotkamp, M.; Witte, U.; Munk, A.; Hartung, A.; Gausmann, S.; Hengesbach, S.; Traub, M.; Hoffmann, H.-D.; Hoeffner, J.; Jungbluth, B.

    2014-02-01

    We present design and first performance data of a broadly tunable Alexandrite laser longitudinally pumped by a newly developed high brightness single emitter diode laser module with output in the red spectral range. Replacing the flashlamps, which are usually used for pumping Alexandrite, will increase the efficiency and maintenance interval of the laser. The pump module is designed as an optical stack of seven single-emitter laser diodes. We selected an optomechanical concept for the tight overlay of the radiation using a minimal number of optical components for collimation, e.g. a FAC and a SAC lens, and focusing. The module provides optical output power of more than 14 W (peak pulse output in the focus) with a beam quality of M2 = 41 in the fast axis and M2 = 39 in the slow axis. The Alexandrite crystal is pumped from one end at a repetition rate of 35 Hz and 200μs long pump pulses. The temperature of the laser crystal can be tuned to between 30 °C and 190 °C using a thermostat. The diode-pumped Alexandrite laser reaches a maximum optical-optical efficiency of 20 % and a slope efficiency of more than 30 % in fundamental-mode operation (M2 < 1.10). When a Findlay-Clay analysis with four different output couplers is conducted, the round-trip loss of the cavity is determined to be around 1 %. The wavelength is tunable to between 755 and 788 nm via crystal temperature or between 745 and 805 nm via an additional Brewster prism.

  14. High power, high efficiency, 2D laser diode arrays for pumping solid state lasers

    SciTech Connect

    Rosenberg, A.; McShea, J.C.; Bogdan, A.R.; Petheram, J.C.; Rosen, A.

    1987-11-01

    This document reports the current performance of 2D laser diode arrays operating at 770 nm and 808 nm for pumping promethium and neodymium solid state lasers, respectively. Typical power densities are in excess of 2kw/cm/sup 2/ with overall efficiencies greater than 30%.

  15. Cs laser with unstable cavity transversely pumped by multiple diode lasers.

    PubMed

    Zhdanov, B V; Shaffer, M K; Knize, R J

    2009-08-17

    We have demonstrated a Cs vapor laser with an unstable resonator transversely pumped by 15 narrowband laser diode arrays. A slope efficiency of 43%, a total optical efficiency of 31% and a maximum output power 49 W were obtained with a pump power of 157 Watts. PMID:19687954

  16. Four-Pass Coupler for Laser-Diode-Pumped Solid-State Laser

    NASA Technical Reports Server (NTRS)

    Coyle, Donald B.

    2008-01-01

    A four-pass optical coupler affords increased (in comparison with related prior two-pass optical couplers) utilization of light generated by a laser diode in side pumping of a solid-state laser slab. The original application for which this coupler was conceived involves a neodymium-doped yttrium aluminum garnet (Nd:YAG) crystal slab, which, when pumped by a row of laser diodes at a wavelength of 809 nm, lases at a wavelength of 1,064 nm. Heretofore, typically, a thin laser slab has been pumped in two passes, the second pass occurring by virtue of reflection of pump light from a highly reflective thin film on the side opposite the side through which the pump light enters. In two-pass pumping, a Nd:YAG slab having a thickness of 2 mm (which is typical) absorbs about 84 percent of the 809-nm pump light power, leaving about 16 percent of the pump light power to travel back toward the laser diodes. This unused power can cause localized heating of the laser diodes, thereby reducing their lifetimes. Moreover, if the slab is thinner than 2 mm, then even more unused power travels back toward the laser diodes. The four-pass optical coupler captures most of this unused pump light and sends it back to the laser slab for two more passes. As a result, the slab absorbs more pump light, as though it were twice as thick. The gain and laser cavity beam quality of a smaller laser slab in conjunction with this optical coupler can thus be made comparable to those of a larger two-pass-pumped laser slab.

  17. Improving Lifetime of Quasi-CW Laser Diode Arrays for Pumping 2-Micron Solid State Lasers

    NASA Technical Reports Server (NTRS)

    Amzajerdian, Farzin; Meadows, Byron L.; Baker, Nathaniel R.; Barnes, Bruce W.; Singh, Upendra N.; Kavaya, Michael J.

    2007-01-01

    Operating high power laser diode arrays in long pulse regime of about 1 msec, which is required for pumping 2-micron thulium and holmium-based lasers, greatly limits their useful lifetime. This paper describes performance of laser diode arrays operating in long pulse mode and presents experimental data on the active region temperature and pulse-to-pulse thermal cycling that are the primary cause of their premature failure and rapid degradation. This paper will then offer a viable approach for determining the optimum design and operational parameters leading to the maximum attainable lifetime.

  18. Fast mode-hop-free acousto-optically tuned laser with a simple laser diode.

    PubMed

    Bösel, André; Salewski, Klaus-Dieter; Kinder, Thomas

    2007-07-01

    A mode-hop-free tunable external-cavity Littrow diode laser with intracavity acousto-optic modulators (AOMs) has been built. The modes of the red laser diode without a special antireflection coating are shifted by varying the injection current. The external resonator modes and the grating selectivity are independently electrically alterable by two AOMs. Thus, a tuning of the external resonator over up to 1900 GHz is possible. A precise computer control of laser diode and AOMs allowed a single-mode tuning of the whole laser with a tuning range of 225 GHz in 250 s. Additionally, we demonstrated fast tuning over 90 GHz in 190 micros and a repetition rate of 2.5 kHz. PMID:17603626

  19. Ion-implanted planar-buried-heterostructure diode laser

    DOEpatents

    Brennan, Thomas M.; Hammons, Burrell E.; Myers, David R.; Vawter, Gregory A.

    1991-01-01

    A Planar-Buried-Heterostructure, Graded-Index, Separate-Confinement-Heterostructure semiconductor diode laser 10 includes a single quantum well or multi-quantum well active stripe 12 disposed between a p-type compositionally graded Group III-V cladding layer 14 and an n-type compositionally graded Group III-V cladding layer 16. The laser 10 includes an ion implanted n-type region 28 within the p-type cladding layer 14 and further includes an ion implanted p-type region 26 within the n-type cladding layer 16. The ion implanted regions are disposed for defining a lateral extent of the active stripe.

  20. Wave optics simulation of diode pumped alkali laser (DPAL)

    NASA Astrophysics Data System (ADS)

    Endo, Masamori; Nagaoka, Ryuji; Nagaoka, Hiroki; Nagai, Toru; Wani, Fumio

    2016-03-01

    A numerical simulation code for a diode pumped alkali laser (DPAL) was developed. The code employs the Fresnel- Kirchhoff diffraction integral for both laser mode and pump light propagations. A three-dimensional rate equation set was developed to determine the local gain. The spectral divergence of the pump beam was represented by a series of monochromatic beams with different wavelengths. The calculated results showed an excellent agreements with relevant experimental results. It was found that the main channel of the pump power drain is the spontaneous emission from the upper level of the lasing transition.

  1. External cavity diode laser with very-low frequency drift

    NASA Astrophysics Data System (ADS)

    Takamizawa, Akifumi; Yanagimachi, Shinya; Ikegami, Takeshi

    2016-03-01

    An external cavity diode laser with significant mechanical robustness was installed in a housing that was sealed from outside for eliminating variations in the refractive index of air. Using the feedback signal for a frequency lock, it was found that the variation in the laser frequency under free running was suppressed to 275 MHz over one month and depended on the room temperature. Moreover, the upper limit of the linear frequency drift rate was evaluated as intrinsically 40 Hz/s. The frequency lock is expected to be sustainable for more than 110 days with temperature-controlled housing.

  2. Monolithically integrated twin ring diode lasers for rotation sensing applications

    NASA Astrophysics Data System (ADS)

    Osiński, Marek; Cao, Hongjun; Liu, Chiyu; Eliseev, Petr G.

    2006-02-01

    Design, fabrication, and characterization of monolithically integrated ring diode lasers (RDLs) with relatively large size are reported. Fully functional optoelectronic integrated circuits containing integrated unidirectional RDLs, photodetectors, and coupling waveguides are demonstrated. Multiple switching of lasing direction is observed in RDL with quantum-well active regions, and an S-section or spiral absorbers are used to suppress directional switching and to obtain a more stable unidirectional operation. Unidirectionality of the RDL operation is greatly improved in lasers with quantum-dot active regions.

  3. Quasi-stadium laser diodes with an unstable resonator condition.

    PubMed

    Fukushima, Takehiro; Harayama, Takahisa; Davis, Peter; Vaccaro, Pablo O; Nishimura, Takehiro; Aida, Tahito

    2003-03-15

    We have observed lasing in a complicated eigenmode of a quasi-stadium laser diode with an unstable resonator consisting of two curved end mirrors obeying an unstable resonator condition and two straight sidewall mirrors. The laser was fabricated by application of a reactive-ion-etching technique to a molecular beam epitaxy-grown graded-index separate-confinement heterostructure single-quantum-well GaAs/AlGaAs structure. The far-field pattern shows that the lasing mode corresponds to the complicated lowest-loss mode obtained numerically by an extended Fox-Li method. PMID:12659262

  4. Generation of turquoise light by sum frequency mixing of a diode-pumped solid-state laser and a laser diode in periodically poled KTP

    NASA Astrophysics Data System (ADS)

    Johansson, Sandra; Spiekermann, Stefan; Wang, Shunhua; Pasiskevicius, Valdas; Laurell, Fredrik; Ekvall, Katrin

    2004-10-01

    We report a simple and efficient method to achieve visible light by sum-frequency mixing radiation from a diode-pumped solid-state laser and a laser diode in a periodically poled KTiOPO4 crystal. Since high-power laser diodes are available at a wide range of wavelengths, it is thereby possible to obtain essentially any wavelength in the visible spectrum by appropriate choice of lasers. For demonstration we choose to construct a light source in the blue-green region. A turquoise output power of 4.0 mW was achieved.

  5. High power diode lasers: technology and application in Europe

    NASA Astrophysics Data System (ADS)

    Behringer, Martin; Eberhard, Franz; Herrmann, Gerhard; Luft, Johann; Maric, J.; Morgott, Stefan; Philippens, Marc; Teich, W.

    2003-03-01

    The application field of high power semiconductor lasers is growing rapidly and covers e.g. solid state laser pumping, metal and plastic welding, hard and soft soldering, suface treatment and others. Preferably those applications are attractive, which do not require extremely high beam quality. We have investigated high power diode-laser bars from 808 nm to 980 nm. The scope of this presentation is on focusability and beam quality. For better beam shaping structures with reduced fill factor of 25% to 30% were developed. They were operated in continuous wave operation at power levels of up to 55 W. Tests indicate extrapolated lifetimes of more than 100,000 hours at 40 W at 980 nm cw and about 10,000 hours at 45 W - 50 W at 940 nm and 808 nm. Monolithically stacked NonostacksR were investigated. Operation up to 100°C with excellent lifetimes could be demonstrated. New concepts and applications for low mode number high power diode lasers like tapered laser bars are presented. Examples for various current areas of interest in European research facilities will be given.

  6. Tunable, diode side-pumped Er: YAG laser

    DOEpatents

    Hamilton, Charles E.; Furu, Laurence H.

    1997-01-01

    A discrete-element Er:YAG laser, side pumped by a 220 Watt peak-power InGaAs diode array, generates >500 mWatts at 2.94 .mu.m, and is tunable over a 6 nm range near about 2.936 .mu.m. The oscillator is a plano-concave resonator consisting of a concave high reflector, a flat output coupler, a Er:YAG crystal and a YAG intracavity etalon, which serves as the tuning element. The cavity length is variable from 3 cm to 4 cm. The oscillator uses total internal reflection in the Er:YAG crystal to allow efficient coupling of the diode emission into the resonating modes of the oscillator. With the tuning element removed, the oscillator produces up to 1.3 Watts of average power at 2.94 .mu.m. The duty factor of the laser is 6.5% and the repetition rate is variable up to 1 kHz. This laser is useful for tuning to an atmospheric transmission window at 2.935 .mu.m (air wavelength). The laser is also useful as a spectroscopic tool because it can access several infrared water vapor transitions, as well as transitions in organic compounds. Other uses include medical applications (e.g., for tissue ablation and uses with fiber optic laser scalpels) and as part of industrial effluent monitoring systems.

  7. Tunable, diode side-pumped Er:YAG laser

    DOEpatents

    Hamilton, C.E.; Furu, L.H.

    1997-04-22

    A discrete-element Er:YAG laser, side pumped by a 220 Watt peak-power InGaAs diode array, generates >500 mWatts at 2.94 {micro}m, and is tunable over a 6 nm range near about 2.936 {micro}m. The oscillator is a plano-concave resonator consisting of a concave high reflector, a flat output coupler, a Er:YAG crystal and a YAG intracavity etalon, which serves as the tuning element. The cavity length is variable from 3 cm to 4 cm. The oscillator uses total internal reflection in the Er:YAG crystal to allow efficient coupling of the diode emission into the resonating modes of the oscillator. With the tuning element removed, the oscillator produces up to 1.3 Watts of average power at 2.94 {micro}m. The duty factor of the laser is 6.5% and the repetition rate is variable up to 1 kHz. This laser is useful for tuning to an atmospheric transmission window at 2.935 {micro}m (air wavelength). The laser is also useful as a spectroscopic tool because it can access several infrared water vapor transitions, as well as transitions in organic compounds. Other uses include medical applications (e.g., for tissue ablation and uses with fiber optic laser scalpels) and as part of industrial effluent monitoring systems. 4 figs.

  8. Transient transfection of mammalian cells using a violet diode laser

    NASA Astrophysics Data System (ADS)

    Torres-Mapa, Maria Leilani; Angus, Liselotte; Ploschner, Martin; Dholakia, Kishan; Gunn-Moore, Frank J.

    2010-07-01

    We demonstrate the first use of the violet diode laser for transient mammalian cell transfection. In contrast to previous studies, which showed the generation of stable cell lines over a few weeks, we develop a methodology to transiently transfect cells with an efficiency of up to ~40%. Chinese hamster ovary (CHO-K1) and human embryonic kidney (HEK293) cells are exposed to a tightly focused 405-nm laser in the presence of plasmid DNA encoding for a mitochondrial targeted red fluorescent protein. We report transfection efficiencies as a function of laser power and exposure time for our system. We also show, for the first time, that a continuous wave laser source can be successfully applied to selective gene silencing experiments using small interfering RNA. This work is a major step towards an inexpensive and portable phototransfection system.

  9. The reliability of /AlGa/As CW laser diodes

    NASA Astrophysics Data System (ADS)

    Ettenberg, M.; Kressel, H.

    1980-02-01

    Major factors bearing on the reliability of (AlGa)As CW laser diodes are reviewed with attention given to the degradation modes of facet mirror damage, contact degradation, and internal damage. Detailed results are provided for the oxide-defined stripe-contact double-heterojunction lasers operated for more than 40,000 h with extrapolations indicating a median time to failure between 100,000 and 1,000,000. Facet damage and contact degradation appear to be under control, and internal damage remains the dominant failure mechanism. Most of the data deals with threshold current increase; however, shifts in far-field pattern and changes in laser modulation characteristics, including self-sustained oscillations, may affect laser performance in real systems.

  10. Characterization of High-power Quasi-cw Laser Diode Arrays

    NASA Technical Reports Server (NTRS)

    Stephen, Mark A.; Vasilyev, Aleksey; Troupaki, Elisavet; Allan, Graham R.; Kashem, Nasir B.

    2005-01-01

    NASA s requirements for high reliability, high performance satellite laser instruments have driven the investigation of many critical components; specifically, 808 nm laser diode array (LDA) pump devices. Performance and comprehensive characterization data of Quasi-CW, High-power, laser diode arrays is presented.

  11. Precision UV laser scribing for cleaving mirror facets of GaN-based laser diodes

    NASA Astrophysics Data System (ADS)

    Krüger, O.; Kang, J.-H.; Spevak, M.; Zeimer, U.; Einfeldt, S.

    2016-04-01

    Laser scribing with a nanosecond-pulsed UV laser operating at 355 nm was used to create precise perforation for die separation of GaN-based laser diodes. Machining depth of single- and multiple-pass scribing was investigated. For pulse energies between 1 and 45 µJ at a pulse repetition frequency of 20 kHz and single scan at 100 mm/min, scribe depths from 15 to 180 µm were obtained. Processing parameters were adjusted to minimize the formation of microcracks due to laser-induced local heating. By using the laser skip-and-scribe technique, the propagation of the cleavage plane could be controlled, irregular breaking could be minimized, and die yield could be improved. Smooth mirror facets with low density of terraces were formed by cleaving. In the vicinity of the laser-treated zone, no detrimental effects on the crystal quality of the multi-quantum wells could be detected by cathodoluminescence. The electro-optical characteristics of broad-area laser diodes fabricated by the laser-assisted process were similar to the ones fabricated using the conventional diamond-tip edge-scribing technique that suffers from low die yield. Our results demonstrate that nanosecond-pulsed UV laser scribing followed by cleaving is a powerful technique for the formation of mirror facets of GaN-based laser diodes.

  12. Evaluation of a satellite laser ranging technique using pseudonoise code modulated laser diodes

    NASA Technical Reports Server (NTRS)

    Ball, Carolyn Kay

    1987-01-01

    Several types of Satellite Laser Ranging systems exist, operating with pulsed, high-energy lasers. The distance between a ground point and an orbiting satellite can be determined to within a few centimeters. A new technique substitutes pseudonoise code modulated laser diodes, which are much more compact, reliable and less costly, for the lasers now used. Since laser diode technology is only now achieving sufficiently powerful lasers, the capabilities of the new technique are investigated. Also examined are the effects of using an avalanche photodiode detector instead of a photomultiplier tube. The influence of noise terms (including background radiation, detector dark and thermal noise and speckle) that limit the system range and performance is evaluated.

  13. Nd:GdVO4 ring laser pumped by laser diodes

    NASA Astrophysics Data System (ADS)

    Hao, E. J.; Li, T.; Wang, Z. D.; Zhang, Y.

    2013-02-01

    The design and operation of a laser diode-pumped Nd:GdVO4 ring laser is described. A composite crystal (Nd:GdVO4/YVO4) with undoped ends is single-end pumped by a fiber-coupled laser diode (LD) at 808 nm. A four-mirror ring cavity is designed to keep the laser operating unidirectionally, which eliminates spatial hole burning in the standing-wave cavity. This laser can operate either as continuous wave (CW) or Q-switched. The single-frequency power obtained was 9.1 W at 1063 nm. Q-switched operation produced 0.23 mJ/pulse at 20 kHz in the fundamental laser.

  14. Diode-laser-pumped Nd:YAG laser injection seeding system

    SciTech Connect

    Schmitt, R.L.; Rahn, L.A.

    1986-03-01

    We have designed and tested a compact injection seeding system consisting of a diode-laser-pumped Nd:YAG master oscillator and a permanent-magnet Faraday isolator. With active resonator frequency stabilization, this system permits highly reliable single-axial-mode operation of a Q-switched Nd:YAG laser over a period of hours. The system is capable of injection seeding both stable and unstable resonator designs and is suitable for injection seeding commercial lasers with only minor modifications.

  15. Case studies of industrial applications of high-power diode laser in Finland

    NASA Astrophysics Data System (ADS)

    Hovikorpi, Jari; Jansson, Anssi; Salminen, Antti

    2003-06-01

    The high power diode laser is a new industrial tool. It has several advantages and disadvantages compared to the conventional industrially used CO2 and Nd:YAG laser. The most promising areas of application of diode laser have been considered to be thin sheet welding and hardening. Quite a few feasibility studies of the use of diode laser have been carried out in Finland. So far there has been some application in which diode laser is the most suitable laser. Typically, the HPDL is integrated to an industrial robot. The welding of stainless steel housing, car door lock and catalytic converters are typical examples of applications in which diode laser has technological as well as economical advantages over the conventional laser and welding techniques. The welding of these products requires good control over the heat input, short through put time and low investment. The weld cross-section of a diode laser weld is, because of conduction limited welding process, more suitable for these applications than the keyhole welding. Hardening of a large gear wheel presents also a good example of an application in which the diode laser makes it possible to economically produce structures that have not earlier been possible. Hardening requires a special form of heat delivery in order to ensure evenly hardened zone and acceptable quality. The application was performed with two high power diode lasers. The case studies of these four applications are presented and discussed in details in this paper.

  16. Selection strategy and reliability assessment for SILEX-communication laser diodes

    NASA Astrophysics Data System (ADS)

    Loeffler, Roland; Menke, Bodo

    1991-03-01

    Steps involved in the search for suitable laser diodes for Semiconductor laser Intersatellite Link EXperiment (SILEX) and evaluation of their capabilities in meeting qualification requirements are discussed. A baseline of the laser diode functional specifications is identified by synthesizing the SILEX system requirements and thereby predicting the desired diode characteristics. Samples of approximately 20 different laser diode types are submitted to comprehensive measurements of their characteristics, spectral widths, mode hopping behavior, far field patterns, wave front errors and astigmatisms under modulation. An evaluation program consisting of a conventional three temperature aging test and sensitivity and environmental tests is defined.

  17. Simple mathematical model for designing laser diode focusing optics with a large numerical aperture

    NASA Astrophysics Data System (ADS)

    Sun, Haiyin

    2014-10-01

    A simple mathematical model is derived for conveniently designing laser diode focusing optics with a large numerical aperture. The astigmatism of laser diode beams and the lens truncation effects are considered in the model. The linearly polarized nature of laser diode beams is also included. Two design examples using this model are presented. Design results show that the lens truncation will increase the size of the focused spot and the value of the M2 factor, and the lens truncation caused a focal shift, which is not enough to correct laser diode beam astigmatism.

  18. Research and Development of Laser Diode Based Instruments for Applications in Space

    NASA Technical Reports Server (NTRS)

    Krainak, Michael; Abshire, James; Cornwell, Donald; Dragic, Peter; Duerksen, Gary; Switzer, Gregg

    1999-01-01

    Laser diode technology continues to advance at a very rapid rate due to commercial applications such as telecommunications and data storage. The advantages of laser diodes include, wide diversity of wavelengths, high efficiency, small size and weight and high reliability. Semiconductor and fiber optical-amplifiers permit efficient, high power master oscillator power amplifier (MOPA) transmitter systems. Laser diode systems which incorporate monolithic or discrete (fiber optic) gratings permit single frequency operation. We describe experimental and theoretical results of laser diode based instruments currently under development at NASA Goddard Space Flight Center including miniature lidars for measuring clouds and aerosols, water vapor and wind for Earth and planetary (Mars Lander) use.

  19. Effect of interface layer on the performance of high power diode laser arrays

    NASA Astrophysics Data System (ADS)

    Zhang, Pu; Wang, Jingwei; Xiong, Lingling; Li, Xiaoning; Hou, Dong; Liu, Xingsheng

    2015-02-01

    Packaging is an important part of high power diode laser (HPLD) development and has become one of the key factors affecting the performance of high power diode lasers. In the package structure of HPLD, the interface layer of die bonding has significant effects on the thermal behavior of high power diode laser packages and most degradations and failures in high power diode laser packages are directly related to the interface layer. In this work, the effects of interface layer on the performance of high power diode laser array were studied numerically by modeling and experimentally. Firstly, numerical simulations using finite element method (FEM) were conducted to analyze the effects of voids in the interface layer on the temperature rise in active region of diode laser array. The correlation between junction temperature rise and voids was analyzed. According to the numerical simulation results, it was found that the local temperature rise of active region originated from the voids in the solder layer will lead to wavelength shift of some emitters. Secondly, the effects of solder interface layer on the spectrum properties of high power diode laser array were studied. It showed that the spectrum shape of diode laser array appeared "right shoulder" or "multi-peaks", which were related to the voids in the solder interface layer. Finally, "void-free" techniques were developed to minimize the voids in the solder interface layer and achieve high power diode lasers with better optical-electrical performances.

  20. Development of Advanced Laser Diode Sources

    NASA Technical Reports Server (NTRS)

    Coleman, J. J.; Papen, G. C.

    1998-01-01

    The design and operation of InGaAs-GaAs-AlGaAs asymmetric cladding ridge waveguide distributed Bragg reflector lasers is presented. Targeted for the remote sensing of water vapor with absorption lines in the lambda approximately 930 nm region, these devices operate CW with threshold currents as low as 11 MA and slope efficiencies as high as 0.37 W/A. Tbey also operate with over 30-dB side-mode suppression, and the typical CW characteristic temperature, T(sub o), is 95 K.

  1. Viability and Regeneration of Chondrocytes after Laser Cartilage Reshaping Using 1,460 nm Diode Laser

    PubMed Central

    Mo, Ji-Hun; Kim, Ji-Sun; Lee, Jae-Wook; Chung, Phil-Sang

    2013-01-01

    Objectives Cartilage reshaping by laser irradiation is used to correct septal and auricular cartilage deformities. Chondrocyte viability following laser irradiation and reshaping has been well established. However, the regeneration process of chondrocyte after laser irradiation has not been revealed yet. The aims of this study were to determine the mechanism of cartilaginous thermal injury and the regenerative process of damaged cartilage following laser irradiation. Methods Laser irradiation was performed on human septal cartilage and rabbit auricular cartilage using a 1,460-nm diode laser. We observed change in the shape of cartilage and evaluated the extent of cartilage injury using live/dead cell assay via confocal microscopy. Hoechst and propidium iodide (PI) staining was used to evaluate the mechanism of chondrocyte injury after laser irradiation. To evaluate the regeneration of cartilage, laser irradiated cartilages were reimplanted into a subperichondrial pocket and were harvested at 1, 2, and 4 weeks after reimplantation for viability assessment and histologic examination. Results Laser irradiation using a 1,460-nm diode laser produced a marked shape change in both human septal and rabbit auricular cartilages. Thermal damage on cartilage was correlated with the exposure time and the laser power. Hoechst and PI staining showed that chondrocyte death by laser irradiation was due to mainly necrosis, rather than apoptosis. In lower power treatment group (0.3 W and 0.5 W), all the chondrocytes regenerated within 4 weeks, however, in 1 W treatment group, chondrocytes could not regenerate until 4 weeks. Conclusion Reshaping of cartilage using 1,460 nm diode laser was attained concurrently with the thermal injury to the chondrocytes. The extent of thermal damage on chondrocytes was dependent on the exposure time and the laser power and the damaged chondrocytes irradiated with lower level of laser power could be regenerated after reimplantation into

  2. High density, optically corrected, micro-channel cooled, v-groove monolithic laser diode array

    DOEpatents

    Freitas, Barry L.

    1998-01-01

    An optically corrected, micro-channel cooled, high density laser diode array achieves stacking pitches to 33 bars/cm by mounting laser diodes into V-shaped grooves. This design will deliver>4kW/cm2 of directional pulsed laser power. This optically corrected, micro-channel cooled, high density laser is usable in all solid state laser systems which require efficient, directional, narrow bandwidth, high optical power density pump sources.

  3. High density, optically corrected, micro-channel cooled, v-groove monolithic laser diode array

    DOEpatents

    Freitas, B.L.

    1998-10-27

    An optically corrected, micro-channel cooled, high density laser diode array achieves stacking pitches to 33 bars/cm by mounting laser diodes into V-shaped grooves. This design will deliver > 4kW/cm{sup 2} of directional pulsed laser power. This optically corrected, micro-channel cooled, high density laser is usable in all solid state laser systems which require efficient, directional, narrow bandwidth, high optical power density pump sources. 13 figs.

  4. Diode-Laser-Based Spectrometer for Sensing Gases

    NASA Technical Reports Server (NTRS)

    Silver, Joel A.

    2005-01-01

    A diode-laser-based spectrometer has been developed for measuring concentrations of gases and is intended particularly for use in analyzing and monitoring combustion processes under microgravitational conditions in a drop tower or a spacecraft. This instrument is also well suited for use on Earth in combustion experiments and for such related purposes as fire-safety monitoring and monitoring toxic and flammable gases in industrial settings. Of the gas-sensing spectrometers available prior to the development of this instrument, those that were sensitive enough for measuring the combustion gases of interest were too large, required critical optical alignments, used far too much electrical power, and were insufficiently rugged for use under the severe conditions of spacecraft launch and space flight. In contrast, the present instrument is compact, consumes relatively little power, and is rugged enough to withstand launch vibrations and space flight. In addition, this instrument is characterized by long-term stability, accuracy, and reliability. The diode laser in this spectrometer is operated in a wavelength-modulation mode. Different gases to be measured can be selected by changing modular laser units. The operation of the laser is controlled by customized, low-power electronic circuitry built around a digital signal-processor board. This customized circuitry also performs acquisition and analysis of data, controls communications, and manages errors.

  5. Two photon absorption in high power broad area laser diodes

    NASA Astrophysics Data System (ADS)

    Dogan, Mehmet; Michael, Christopher P.; Zheng, Yan; Zhu, Lin; Jacob, Jonah H.

    2014-03-01

    Recent advances in thermal management and improvements in fabrication and facet passivation enabled extracting unprecedented optical powers from laser diodes (LDs). However, even in the absence of thermal roll-over or catastrophic optical damage (COD), the maximum achievable power is limited by optical non-linear effects. Due to its non-linear nature, two-photon absorption (TPA) becomes one of the dominant factors that limit efficient extraction of laser power from LDs. In this paper, theoretical and experimental analysis of TPA in high-power broad area laser diodes (BALD) is presented. A phenomenological optical extraction model that incorporates TPA explains the reduction in optical extraction efficiency at high intensities in BALD bars with 100μm-wide emitters. The model includes two contributions associated with TPA: the straightforward absorption of laser photons and the subsequent single photon absorption by the holes and electrons generated by the TPA process. TPA is a fundamental limitation since it is inherent to the LD semiconductor material. Therefore scaling the LDs to high power requires designs that reduce the optical intensity by increasing the mode size.

  6. Tunable laser diode system for noninvasive blood glucose measurements.

    PubMed

    Olesberg, Jonathon T; Arnold, Mark A; Mermelstein, Carmen; Schmitz, Johannes; Wagner, Joachim

    2005-12-01

    Optical sensing of glucose would allow more frequent monitoring and tighter glucose control for people with diabetes. The key to a successful optical noninvasive measurement of glucose is the collection of an optical spectrum with a very high signal-to-noise ratio in a spectral region with significant glucose absorption. Unfortunately, the optical throughput of skin is low due to absorption and scattering. To overcome these difficulties, we have developed a high-brightness tunable laser system for measurements in the 2.0-2.5 microm wavelength range. The system is based on a 2.3 microm wavelength, strained quantum-well laser diode incorporating GaInAsSb wells and AlGaAsSb barrier and cladding layers. Wavelength control is provided by coupling the laser diode to an external cavity that includes an acousto-optic tunable filter. Tuning ranges of greater than 110 nm have been obtained. Because the tunable filter has no moving parts, scans can be completed very quickly, typically in less than 10 ms. We describe the performance of the present laser system and avenues for extending the tuning range beyond 400 nm. PMID:16390586

  7. Development of diode laser-ignited pyrotechnic and explosive components

    SciTech Connect

    Jungst, R.G.; Salas, F.J.; Watkins, R.D.; Kovacic, L.

    1990-01-01

    Studies are described which have led to the development of prototype diode laser-ignited pyrotechnic and explosive devices. These are of interest because they eliminate some concerns associated with ignition from hot wires such as conductance after firing, sensitivity to electromagnetic radiation and electrostatic discharge, and bridgewire corrosion. The availability of high power diode lasers is a key feature for the success of this concept. A pyrotechnic, Ti/KClO{sub 4}, and the deflagration-to-detonation transition (DDT) explosive CP have been evaluated and found suitable for use in LDI components. Doping with materials such as carbon black to increase light absorption near 800 nm is a major factor in reducing the laser power required to ignite CP, but does not strongly affect the ignition of Ti/KClO{sub 4}. Other material and laser input parameters were also studied to determine their influence on ignition thresholds. Even though they contain different energetic materials, the energy-power relationship of these optical igniters was generally similar in shape to those of other thermal ignition devices such as stable and electric igniters. Prototype, hermetically sealed, optical headers have been fabricated, loaded, and test fired with CP and Ti/KClO{sub 4}. Glass to metal sealing technology has been developed to insert sapphire windows or optical fiber segments in these fixtures. Devices containing fiber segments demonstrated superior performance in threshold tests. 8 refs., 12 figs., 3 tabs.

  8. Perovskite Materials for Light-Emitting Diodes and Lasers.

    PubMed

    Veldhuis, Sjoerd A; Boix, Pablo P; Yantara, Natalia; Li, Mingjie; Sum, Tze Chien; Mathews, Nripan; Mhaisalkar, Subodh G

    2016-08-01

    Organic-inorganic hybrid perovskites have cemented their position as an exceptional class of optoelectronic materials thanks to record photovoltaic efficiencies of 22.1%, as well as promising demonstrations of light-emitting diodes, lasers, and light-emitting transistors. Perovskite materials with photoluminescence quantum yields close to 100% and perovskite light-emitting diodes with external quantum efficiencies of 8% and current efficiencies of 43 cd A(-1) have been achieved. Although perovskite light-emitting devices are yet to become industrially relevant, in merely two years these devices have achieved the brightness and efficiencies that organic light-emitting diodes accomplished in two decades. Further advances will rely decisively on the multitude of compositional, structural variants that enable the formation of lower-dimensionality layered and three-dimensional perovskites, nanostructures, charge-transport materials, and device processing with architectural innovations. Here, the rapid advancements in perovskite light-emitting devices and lasers are reviewed. The key challenges in materials development, device fabrication, operational stability are addressed, and an outlook is presented that will address market viability of perovskite light-emitting devices. PMID:27214091

  9. Construction of a Visible Diode Laser Source for Free Radical Photochemistry and Spectroscopy Experiments

    NASA Technical Reports Server (NTRS)

    Newman, Bronjelyn; Halpern, Joshua B.

    1997-01-01

    Tunable diode lasers are reliable sources of narrow-band light and comparatively cheap. Optical feedback simplifies frequency tuning of the laser diodes. We are building an inexpensive diode laser system incorporating optical feedback from a diffraction grating. The external optical cavity can be used with lasers that emit between 2 and 100 mW, and will also work if they are pulsed, although this will significantly degrade the bandwidth. The diode laser output power and bandwidth are comparable to CW dye lasers used in kinetics and dynamics experiments. However, their cost and maintenance will be much less as will alignment time. We intend to use the diode lasers to investigate CN and C2 kinetics as well as to study dissociation dynamics of atmospherically important molecules.

  10. Efficient femtosecond Yb:YAG laser pumped by a single-mode laser diode

    NASA Astrophysics Data System (ADS)

    Agnesi, Antonio; Greborio, Alessandro; Pirzio, Federico; Reali, Giancarlo

    2011-08-01

    Single-mode diodes enable a particularly simple, compact and effective pumping of solid-state laser devices for many specialized applications. We investigated a single-mode, 300-mW laser diode for pumping at 935 nm a Yb:YAG laser passively mode-locked by a semiconductor saturable absorber. Relatively short pulse generation (156 fs), tunable across 1033-1059 nm has been demonstrated. An optical-to-optical efficiency of about 28% has been obtained with 320 fs long pulses. Therefore, contrarily to what previously believed, compact diode-pumped ultrafast Yb:YAG oscillators can reliably and efficiently deliver pulses in the range of ≈ 100-200 fs with few tens of mW, which are very appealing for bio-diagnostics and amplifier seeding applications.

  11. Developments in laser joining and welding of plastics using high-power laser diodes

    NASA Astrophysics Data System (ADS)

    Hoult, Tony; Ong, Raymond

    2002-02-01

    Diode lasers are now being employed in industry for a range of applications, in particular they are starting to be used as alternatives to conventional techniques for thermal joining of plastics. This is being assisted by the use of improved reliability aluminum-free diodes and diode laser systems, partly due to a better understanding of failure mechanisms. The laser welding and related techniques are dependent on transmission of part of an infra-red beam through the upper layer of a joint and semi-quantitative assessment of this is required for specific applications. The technique is applicable not only to high average powers, but also to very low average power, in this regime delicate thin-walled components may be joined. Recent developments using derivatives of this technique have shown that a wide range of similar and dissimilar material combinations may be joined.

  12. Coherent communication link using diode-pumped lasers

    NASA Technical Reports Server (NTRS)

    Kane, Thomas J.; Wallace, Richard W.

    1989-01-01

    Work toward developing a diffraction limited, single frequency, modulated transmitter suitable for coherent optical communication or direct detection communication is discussed. Diode pumped, monolithic Nd:YAG nonplanar ring oscillators were used as the carrier beam. An external modulation technique which can handle high optical powers, has moderate modulation voltage, and which can reach modulation rates of 1 GHz was invented. Semiconductor laser pumped solid-state lasers which have high output power (0.5 Watt) and which oscillate at a single frequency, in a diffraction limited beam, at the wavelength of 1.06 microns were built. A technique for phase modulating the laser output by 180 degrees with a 40-volt peak to peak driving voltage is demonstrated. This technique can be adapted for amplitude modulation of 100 percent with the same voltage. This technique makes use of a resonant bulk modulator, so it does not have the power handling limitations of guided wave modulators.

  13. Microarterial anastomoses using the diode laser: long term morphological results

    NASA Astrophysics Data System (ADS)

    Tang, Jing; Prudhomme, Michel; Rouy, Simone; Godlewski, Guilhem; Ovtchinikoff, Serge; Delacretaz, Guy P.; Salathe, Rene-Paul

    1996-01-01

    In a series of 70 Wistar rats submitted to a noncontact diode laser-assisted carotid end-to-end anastomosis (LAMA) versus controlateral manual suture microanastomosis (CMA), contrast angiography and scanning electron microscopy were performed in a group of 18 animals at a long-term follow up to 7 months after operation. The investigation of angiography realized by means of a CGR General Electric DG 200 with a 512 digital matrix gave precise images of vessel wall repair and vessel patency. It permitted a simultaneous comparison between laser and manual anastomosis. Patency rate was 83% in LAMA and 78% in CMA. Nonlethal complications such as 1 stenosis, 2 thromboses in LAMA and 1 stenosis, 2 thromboses, and 1 pseudoaneurysm in CMA were observed. The results could be correlated to scanning electron microscopy findings and confirmed the morphological superiority of the laser technique.

  14. Diode-Pumped Mode-Locked LiSAF Laser

    SciTech Connect

    1996-02-01

    Under this contract we have developed Cr{sup 3+}:LiSrAlF{sub 6} (Cr:LiSAF, LiSAF) mode-locked lasers suitable for generation of polarized electrons for CEBAF. As 670 nm is an excellent wavelength for optical pumping of Cr:LiSAF, we have used a LIGHTWAVE developed 670 nm diode pump module that combines the output of ten diode lasers and yields approximately 2 Watts of optical power. By the use of a diffraction limited pump beam however, it is possible to maintain a small mode size through the length of the crystal and hence extract more power from Cr:LiSAF laser. For this purpose we have developed a 1 Watt, red 660nm laser (LIGHTWAVE model 240R) which serves as an ideal pump for Cr:LiSAF and is a potential replacement of costly and less robust krypton laser. This new system is to compliment LIGHTWAVE Series 240, and is currently being considered for commercialization. Partially developed under this contract is LIGHTWAVEs product model 240 which has already been in our production lines for a few months and is commercially available. This laser produces 2 Watts of output at 532 nm using some of the same technology developed for production of the 660nm red system. It is a potential replacement for argon ion lasers and has better current and cooling requirements and is an excellent pump source for Ti:Al{sub 2}O{sub 3}. Also, as a direct result of this contract we now have the capability of commercially developing a mode-locked 100MHz Cr:LiSAF system. Such a laser could be added to our 100 MHz LIGHTWAVE Series 131. The Series 131 lasers provide pico second pulses and were originally developed under another DOE SBIR. Both models of LIGHTWAVE Series 240 lasers, the fiber coupled pump module and the 100MHz LiSAF laser of Series 131 have been partially developed under this contract, and are commercially competitive products.

  15. Diode laser supported partial nephrectomy in laparoscopic surgery: preliminary results

    NASA Astrophysics Data System (ADS)

    Sroka, Ronald; Hennig, Georg; Zillinberg, Katja; Khoder, Wael Y.

    2011-07-01

    Introduction: Warm ischemia and bleeding during laparoscopic partial nephrectomy place technical constraints on surgeons. Therefore it was the aim to develop a safe and effective laser assisted partial nephrectomy technique without need for ischemia. Patients and methods: A diode laser emitting light at 1318nm in cw mode was coupled into a bare fibre (core diameter 600 μm) thus able to transfer up to 100W to the tissue. After dry lab experience, a total of 8 patients suffering from kidney malformations underwent laparoscopic/retroperitoneoscopic partial nephrectomy. Clinically, postoperative renal function and serum c-reactive protein (CRP) were monitored. Laser induced coagulation depth and effects on resection margins were evaluated. Demographic, clinical and follow-up data are presented. Results: Overall interventions, the mean operative time was 116,5 minutes (range 60-175min) with mean blood loss of 238ml (range 50-600ml) while laser assisted resection of the kidney tissue took max 15min. After extirpation of the tumours all patients showed clinical favourable outcome during follow up period. The tumour size was measured to be 1.8 to 5cm. With respect to clinical safety and due to blood loos, two warm ischemia (19 and 24min) must be performed. Immediate postoperative serum creatinine and CRP were elevated within 0.1 to 0.6 mg/dl (mean 0.18 mg/dl) and 2.1-10 mg/dl (mean 6.24 mg/dl), respectively. The depth of the coagulation on the removed tissue ranged between <1 to 2mm without effect on histopathological evaluation of tumours or resection margin. As the surface of the remaining kidney surface was laser assisted coagulated after removal. The sealing of the surface was induced by a slightly larger coagulation margin, but could not measured so far. Conclusion: This prospective in-vivo feasibility study shows that 1318nm-diode laser assisted partial nephrectomy seems to be a safe and promising medical technique which could be provided either during open surgery

  16. Preliminary Study on Generating Condition of Laser Sustained Plasma using 1 kW CW Diode Laser

    NASA Astrophysics Data System (ADS)

    Nishimoto, Koji; Kumita, Mamoru; Matsui, Makoto

    2015-09-01

    In the laser sustained plasma of conventional laser driven plasma wind tunnel, CO2 laser have been used. However, the efficiency of is about 10%. Recently, the development of diode laser is remarkable and the energy efficiency of it reaches nearly 80% in laboratory stage. Therefore, in our research group, the generation of laser sustained plasma using diode laser is being tried. In this study, the generation threshold of it was numerically calculated. Assuming that focused laser diameter is 200 um, in the condition of the pressure of 0.1-1 MPa, it was deduced that the threshold of laser power is about 500 W.

  17. High power diode laser stack development using gold-tin bonding technology

    NASA Astrophysics Data System (ADS)

    Hou, Dong; Wang, Jingwei; Zhang, Pu; Cai, Lei; Dai, Ye; Li, Yingjie; Liu, Xingsheng

    2015-02-01

    High power diode lasers have increased application in many fields. In this work, a sophisticated high power and high performance conduction cooled diode laser stack has been developed for long pulse duration and high duty cycle using gold-tin (AuSn) bonding technology. The transient thermal behavior and optical simulation of the laser diode stack module are investigated to optimize the laser device structure. CTE-matched submount and AuSn hard solder are used for bonding the laser diode bar to achieve higher reliability and longer lifetime. Guided by the numerical simulation and analytical results, conduction cooled diode laser stack with high power, long pulse duration and high duty cycle is fabricated and characterized. Compared with the conventional indium bonding technology, the new design is a promising approach to obtain improved performance with high reliability and long lifetime.

  18. Thin planar package for cooling an array of edge-emitting laser diodes

    DOEpatents

    Mundinger, David C.; Benett, William J.

    1992-01-01

    A laser diode array is disclosed that includes a plurality of planar assemblies and active cooling of each assembly. The laser diode array may be operated in a long duty cycle, or in continuous operation. A laser diode bar and a microchannel heat sink are thermally coupled in a compact, thin planar assembly having the laser diode bar located proximate to one edge. In an array, a number of such thin planar assemblies are secured together in a stacked configuration, in close proximity so that the laser diodes are spaced closely. The cooling means includes a microchannel heat sink proximate to the laser diode bar to absorb heat generated by laser operation. To provide the coolant to the microchannels, each thin planar assembly comprises passageways that connect the microchannels to inlet and outlet corridors. Each inlet passageway may comprise a narrow slot that directs coolant into the microchannels and increases the velocity of flow therethrough. The corridors comprises holes extending through each of the assemblies in the array. The inlet and outlet corridors are connected to a conventional coolant circulation system. The laser diode array with active cooling has applications as an optical pump for high power solid state lasers, or by mating the diodes with fiber optic lenses. Further, the arrays can be useful in applications having space constraints and energy limitations, and in military and space applications. The arrays can be incorporated in equipment such as communications devices and active sensors.

  19. Treatment of Dentine Hypersensitivity by Diode Laser: A Clinical Study

    PubMed Central

    Umberto, Romeo; Claudia, Russo; Gaspare, Palaia; Gianluca, Tenore; Alessandro, Del Vecchio

    2012-01-01

    Introduction. Dentine hypersensitivity (DH) is characterized by pain after stimuli that usually provoke no symptoms. This study compared the effectiveness of GaAlAs diode laser alone and with topical sodium fluoride gel (NaF). Materials and Methods. The study was conducted on 10 patients (8 F/2 M, age 25–60) and 115 teeth with DH assessed by air and tactile stimuli measured by Numeric Rating Scale (NRS). Teeth were randomly divided into G1 (34 teeth) treated by 1.25% NaF; G2 (33 teeth) lased at 0.5 W PW (T on 100 m and T off 100 ms), fluence 62.2 J/cm2 in defocused mode with a 320 μ fiber. Each tooth received three 1′ applications; G3 (48 teeth) received NaF gel plus laser at same G2 parameters. NRS was checked at each control. Results. Significant pain reduction was showed. The NRS reduction percentages were calculated, and there was a concrete decrease of DH above all in G3 than G2 and G1. Conclusion. Diode laser is a useful device for DH treatment if used alone and mainly if used with NaF gel. PMID:22792109

  20. Performance of commercial laser diodes in fluorimetric detection

    NASA Astrophysics Data System (ADS)

    Wersig, C.; Finke, W.; Handler, E.; Josel, Hans-Peter; Schmidt, Elmar

    1993-05-01

    We have developed a compact and sensitive detection system based on the fluorescence excitation by commercial laser diodes in the VIS and NIR. The system comprises separate excitation, sample, and detection chambers and shows the potential of quantitatively determining immunological and other parameters with small and rugged instruments. Our examinations specifically addressed technical aspects of laser diodes which are responsible for the quality of fluorescence excitation, such as the characterization of the mode structure, the temperature and current dependency of the optical power emission, and the selection and adjustment of the laser wavelengths for optimal overlap with the fluorophors' absorption maxima (namely rhodamine 800, indocyanine green IR-125, and latex-bound dyes). Signal-to- noise level ratios of about 1:1 are reached at sub-nanomolar concentrations in an illuminated sample of 20 (mu) l using a standard photomultiplier tube in analog mode as the detector. Different arrangements of optical filters (e.g., interference, colored-glass type, and polarizing filters) have been optimized with regard to the excitation and detection paths. Furthermore, measures toward an internal calibration of the system have been investigated.

  1. Blue diode laser: a new approach in oral surgery?

    NASA Astrophysics Data System (ADS)

    Fornaini, Carlo; Merigo, Elisabetta; Selleri, Stefano; Cucinotta, Annamaria

    2016-02-01

    The introduction of diode lasers in dentistry had several advantages, principally consisting on the reduced size, reduced cost and possibility to beam delivering by optical fibbers. Up today two diode wavelengths, 810 and 980 nm, were the most utilized in oral surgery but recently a new wavelength emitting in the blue had been proposed. The aim of this ex vivo study was to compare the efficacy of five laser wavelengths (450, 532, 808, 1064 and 1340 nm) for the ablation of soft tissues. Specimens were surgically collected from the dorsal surface of four bovine tongues and irradiated by the five different wavelengths. Thermal increase was measured by two thermocouples, the first at a depth of 0.5 mm, and the second at a depth of 2 mm while initial and final surface temperatures were recorded by IR thermometer. The quality of the incision was histologically evaluated by a pathologist by giving a score from 0 to 5. The time necessary to perform the excision varied between 215 seconds (1340 nm, 5W) and 292 seconds (808 nm, 3W). Surface temperature increase was highest for 1340 nm, 5W and lowest for 405 nm, 4 W. The most significant deep temperature increase was recorded by 1340 nm, 5 W and the lowest by 450 nm, 2 W. The quality of incision was better and the thermal elevation lower in the specimens obtained with shortest laser wavelength (450 nm).

  2. High-power diode lasers in spray process diagnostics

    NASA Astrophysics Data System (ADS)

    Larjo, Jussi

    2005-03-01

    Spray processes are commonly employed in many kinds of surface treatment applications, most prominently in medical, material processing and manufacturing industries. While spraying is a well established technology, we still lack complete understanding of all interactions within a given spray process. This is because the physical models of many subprocesses, like turbulent gas flow, particle formation and gas-particle interaction, are limited and often provide only qualitative predictions on the real process. Imaging measurements are essential in gaining better understanding of a spray process. They offer a way to measure properties of both the complete spray plume and individual droplets. A spray analysis system typically requires a high-power stroboscopic light source; Xe flashlamps and Q-switched solid state lasers have been the most common choice until recently. The development of high-power diode lasers has provided a versatile, low-cost and easy to use light source for the analysis of spray processes. We present a real-time diode laser based imaging system to measure droplet density, size and velocity distributions in a spray, together with the spray plume geometry.

  3. Comprehensive Welding of Thermoplastics by a Diode Laser

    NASA Astrophysics Data System (ADS)

    Sato, Kimitoshi; Saito, Takushi; Kurosaki, Yasuo

    This paper deals with a development of “comprehensive" laser welding of thermoplastics with versatility in color and shape of products. Overlap welding of thermoplastics is one of the features of application of diode lasers. Most of thermoplastics are transparent to diode lasers; therefore it is need to weld plastic article with colorant. The influence of absorptance and transmittance of overlapping colored plastics were studied. Various colored plastics with infrared-transparent pigments were tested as the welding material. The appropriate absorptance and transmittance of overlapping colored plastic were examined. The feasibility of the technique of welding of transparent plastics using infrared-absorbing layer was also investigated. The temperature distribution within the plastics was calculated by numerical simulation in order to estimate the validity of the proposing experimental systems. It was confirmed by the experiments that the 35μm film, which shows only 10% in absorptance is enough to weld a pair of transparent articles as infrared-absorbing layer.

  4. Diode-laser-based ultraviolet absorption sensor for nitric oxide

    NASA Astrophysics Data System (ADS)

    Hanna, S. F.; Barron-Jimenez, R.; Anderson, T. N.; Lucht, R. P.; Caton, J. A.; Walther, T.

    2002-07-01

    An all-solid-state continuous-wave laser system for ultraviolet absorption measurements of the nitric oxide (NO) molecule has been developed and demonstrated. The single-mode, tunable output of a 10-mW, 395-nm external-cavity diode laser (ECDL) is sum-frequency-mixed with the output of a 115-mW, frequency-doubled, diode-pumped Nd:YAG laser in a beta-barium-borate crystal to produce 40 nW of tunable radiation at 226.8 nm. The wavelength of the 395-nm ECDL is then scanned over NO absorption lines to produce fully resolved absorption spectra. Initial results from mixtures of NO in nitrogen in a room-temperature gas cell are discussed. The estimated NO detection limit of the system for a demonstrated absorption sensitivity of 2×10-3 is 0.2 ppm per meter of path length for 300 K gas. The estimated accuracy of the measurements is ±10%.

  5. Temperature control during diode laser welding in a human cornea

    NASA Astrophysics Data System (ADS)

    Rossi, Francesca; Matteini, Paolo; Pini, Roberto; Menabuoni, Luca

    2007-07-01

    Diode laser welding is a technique proposed in ophthalmic surgery to induce immediate sealing of clear corneal wounds. The welding effect is achieved irradiating the area, previously treated with a chromophore, by the use of a low power diode laser: the resulting thermal effect induces structural modifications in the stromal collagen, that welds upon cooling. We present a study on the temperature dynamics developing during welding in a human eye. An infrared thermocamera was used to measure the temperature variations on the surface of the cornea during clinical penetrating keratoplasty (corneal transplant). The experimental data were used as a starting point for a theoretical investigation of the temperature rising inside the ocular structures: we developed a mathematical model based on the bio-heat equation and solved by the use of the Finite Element Method (FEM). The predictive accuracy was verified by comparing the temperature post-processing description with the results obtained from the thermographic data. The model was then used to study the temperature rise and heat propagation inside the eye. Experimental results and model analysis indicated the occurrence of heat confinement during the treatment procedure and a modest enhancement of the temperature (reaching about 55°C inside the laser treated wound), thus evidencing the safety of the procedure in clinical applications.

  6. Coagulative and ablative characteristics of a novel diode laser system (1470nm) for endonasal applications

    NASA Astrophysics Data System (ADS)

    Betz, C. S.; Havel, M.; Janda, P.; Leunig, A.; Sroka, R.

    2008-02-01

    Introduction: Being practical, efficient and inexpensive, fibre guided diode laser systems are preferable over others for endonasal applications. A new medical 1470 nm diode laser system is expected to offer good ablative and coagulative tissue effects. Methods: The new 1470 nm diode laser system was compared to a conventional 940 nm system with regards to laser tissue effects (ablation, coagulation, carbonization zones) in an ex vivo setup using fresh liver and muscle tissue. The laser fibres were fixed to a computer controlled stepper motor, and the light was applied using comparable power settings and a reproducible procedure under constant conditions. Clinical efficacy and postoperative morbidity was evaluated in two groups of 10 patients undergoing laser coagulation therapy of hyperplastic nasal turbinates. Results: In the experimental setup, the 1470 nm laser diode system proved to be more efficient in inducing tissue effects with an energy factor of 2-3 for highly perfused hepatic tissue to 30 for muscular tissue. In the clinical case series, the higher efficacy of the 1470 nm diode laser system led to reduced energy settings as compared to the conventional system with comparable clinical results. Postoperative crusting was less pronounced in the 1470 nm laser group. Conclusion: The 1470 nm diode laser system offers a highly efficient alternative to conventional diode laser systems for the coagulation of hyperplastic nasal turbinates. According to the experimental results it can be furthermore expected that it disposes of an excellent surgical potential with regards to its cutting abilities.

  7. Generation of 369.4 nm Radiation by Efficient Doubling of a Diode Laser

    NASA Technical Reports Server (NTRS)

    Williams, A.; Seidel, D. J.; Maleki, J.

    1993-01-01

    A resonant cavity second harmonic generation system has been developed to produce 369.4 nm radiation from a 738.8 nm diode laser with 10 mW nominal output power. This system utilizes a polarization technique to lock the cavity to the laser frequency. In this paper we report on an evaluation of the system using a Titanium:Sapphire laser as the input source, and preliminary results with a diode laser source. To our knowledge, this is the deepest uv light ever produced by frequency-doubling a diode laser.

  8. Diode laser excited optogalvanic spectroscopy of glow discharges

    SciTech Connect

    Barshick, C.M.; Shaw, R.W.; Post-Zwicker, A., Young, J.P.; Ramsey, J.M.

    1996-10-01

    The development of diode-laser-excited isotopically-selective optogalvanic spectroscopy (OGS) of uranium metal, oxide and fluoride in a glow discharge (GD) is presented. The technique is useful for determining isotopic ratios of {sup 235}U/({sup 235}U + {sup 238}U) in the above samples. The precision and accuracy of this determination is evaluated, and a study of experimental parameters pertaining to optimization of he measurement is discussed. Application of the GD-OGS to other f-transition elements is also described.

  9. Record-brightness laser-diode bars for fiber coupling

    NASA Astrophysics Data System (ADS)

    Dogan, M.; Pathak, R.; Ellison, S.; Eppich, H.; Campbell, G.; Vignati, J.; Jacob, J. H.; Lang, K. D.; Chin, R. H.; Knapczyk, M. T.; Sun, W.; Fulghum, S. F.; Chin, A. K.

    2012-03-01

    High brightness, laser-diode bars are required for efficient coupling into small-core optical-fibers. Record power and brightness results were achieved using 20% fill-factor, 980nm, 1cm-wide, 4mm cavity-length bars. Lifetimes of single bars, operated CW at 200W and 20°C, exceed 1000hr. Due to superb thermal management, the power conversion efficiency (PCE) exceeds 60% at 200W output power. Similar lifetime and PCE were obtained for a 3-bar stack emitting 600W output power.

  10. Edge-emitting diode lasers with narrow circular beam output

    NASA Astrophysics Data System (ADS)

    Wang, Lijie; Tong, Cunzhu; Zeng, Yugang; Ning, Yongqiang; Wang, Lijun

    2015-05-01

    We report near circular beam output from 808 nm edge-emitting diode lasers based on Bragg reflection waveguide design. Increasing quantum well number combined with reducing defect layer index and thickness was used to achieve high power output and extremely low vertical far field divergence. The TQW-BRLs achieve the lowest vertical divergence of 4.91° (full width at half maximum) and 9.8° (95% power). The maximum power of 4.6 W was achieved in the mounted DQW-BRL device under continuous-wave operation, being limited by thermal rollover.

  11. Early fire sensing using near-IR diode laser spectroscopy

    NASA Astrophysics Data System (ADS)

    Bomse, David S.; Hovde, D. Christian; Chen, Shin-Juh; Silver, Joel A.

    2002-09-01

    We describe research leading to a trace gas detection system based on optical absorption using near-IR diode lasers that is intended to provide early warning of incipient fires. Applications include "high loss" structures such as office buildings, hospitals, hotels and shopping malls as well as airplanes and manned spacecraft where convention smoke detectors generate unacceptably high false alarm rates. Simultaneous or near-simultaneous detection of several gases (typically carbon dioxide, carbon monoxide, acetylene and hydrogen cyanide) provides high sensitivity while reducing the chance of false alarms. Continuous measurement of carbon dioxide concentrations also provides an internal check of instrument performance because ambient levels will not drop below ~350 ppm.

  12. Stable isotope analysis using tunable diode laser spectroscopy

    NASA Technical Reports Server (NTRS)

    Becker, Joseph F.; Sauke, Todd B.; Loewenstein, Max

    1992-01-01

    Ratios of C-12/C-13 in CO2 have been measured using a tunable diode laser (TDL) spectrometer to an accuracy of better than 0.4 percent. These results were made possible by the use of state-of-the-art high-temperature TDLs, an etalon and wavenumber calibration technique, high-speed assembly language controlled data acquisition, and the ratioing of absorbances from simultaneously acquired sample and reference data scans. The dual beam spectrometer that is employed uses the sweep integration technique in a spectral region where adjacent spectral lines are of approximately equal absorbance at the expected isotopic abundances.

  13. Diode-laser frequency stabilization based on the resonant Faraday effect

    NASA Technical Reports Server (NTRS)

    Wanninger, P.; Valdez, E. C.; Shay, T. M.

    1992-01-01

    The authors present the results of a method for frequency stabilizing laser diodes based on the resonant Faraday effects. A Faraday cell in conjunction with a polarizer crossed with respect to the polarization of the laser diode comprises the intracavity frequency selective element. In this arrangement, a laser pull-in range of 9 A was measured, and the laser operated at a single frequency with a linewidth less than 6 MHz.

  14. Laser diode pumped high efficiency Yb:YAG crystalline fiber waveguide lasers

    NASA Astrophysics Data System (ADS)

    Mu, Xiaodong; Meissner, Stephanie; Meissner, Helmuth

    2015-02-01

    Single-clad and double-clad Yb:YAG crystalline fiber waveguides (CFWs) have been prepared with Adhesive-Free Bonding (AFB®) technology. By using a fiber coupled laser diode as pump source, a single-mode laser with near diffraction limited beam quality M2=1.02 has been demonstrated in a double-clad CFW. The laser output power and efficiency are 13.2 W and 34%, respectively. In a single-clad CFW, core pumping was used. The laser output has top-hat beam profile. An output power of 28 W and a slope efficiency of 78% have been achieved respectively.

  15. Laser diode end-pumped ND:YAG laser. Memorandum report

    SciTech Connect

    Elder, I.F.

    1992-01-01

    100 Hz operation of a Nd:YAG laser longitudinally pumped by a 1 W peak power quasi-cw laser diode was investigated theoretically and experimentally. An optical-to-optical slope efficiency of 33%, indicating a wall-plug efficiency of 7%, was exhibited, but the threshold optical power of 330 mW was high due to poor antireflection coatings on the laser rod giving a round-trip intracavity loss of 3.1 %. The 1.064 micrometer output was observed to be diffraction-limited. The theoretical modelling of the laser's input/ output characteristics agreed well with the experimentally obtained results.

  16. Laser diode pumped 1μ Nd;YAG and Nd:BEL lasers

    NASA Astrophysics Data System (ADS)

    Scheps, R.; Poirier, P.; Myers, J. F.; Heller, D. F.

    1989-10-01

    Peformance data for laser diode-pumped cw Nd:YAG and Nd:BEL lasers are presented. Two single stripe laser diodes are used as the pump source, each emitting 1 W in the pump band. The heat sink for the lasers is temperature controlled to allow for wavelength tunability. The resonator is based on a hemispherical design. Output and pump threshold measurements were made and gain and loss for Nd in both hosts were measured. The output power from the Nd:YAG rod was in excess of 870 mW with a slope efficiency of 58% and an overall electrical efficiency of 13%. In Nd:BEL, the output power was in excess of 635 mW with a slope efficiency of 49% and an electrical efficiency of 9.5%.

  17. Tunable diode laser development and spectroscopy applications; Proceedings of the Meeting, San Diego, CA, August 25, 26, 1983

    NASA Astrophysics Data System (ADS)

    Lo, W.

    1983-01-01

    Aspects of tunable diode laser development are discussed, taking into account tunable diode lasers for 3-30 micron infrared operation, Cd-diffused lead salt diode lasers and their application in multicomponent gas analysis systems, heterojunction stripe geometry lead salt diode lasers grown by molecular beam epitaxy, Pb(1-x)Sn(x)Te lasers with high efficiencies, lasing characteristics of PbSnSeTe-PbSeTe lattice-matched double heterostructure laser diodes, and the development of ion-implantation confined shallow mesa stripe (Pb,Sn)Te/Pb(Te/Se) DH laser diodes. Other topics considered are related to industrial applications, applications for tunable diode laser instrumentation, and molecular spectroscopy applications. Attention is given to tunable diode laser applications to cigarette smoke analysis, automated tunable diode laser monitoring systems, a review of progress in remote sensing by tunable diode laser heterodyne spectroscopy, tunable diode laser optogalvanic spectroscopy of molecules, tunable diode laser spectroscopy of molecules in solids and on surfaces, and measurements of CO in engine exhaust.

  18. Study on frequency control method for DBR laser diode based on FPGA

    NASA Astrophysics Data System (ADS)

    Hao, Jiepeng; Hong, Jintao; Chen, Linlin; Lei, Guanqun; Zhou, Binquan

    2015-10-01

    In recent years, the distributed Bragg reflector (DBR) laser diode (LD) has advantages of its small size, high efficiency, low power consumption and so on, so it has been widely used in precision measurement, optical information processing, quantum research and other fields. There is a strict requirement for the output frequency of the DBR laser diode in precision measurement technology. Therefore, controlling the frequency of the laser accurately is of great significance for precision measurement. Currently, there are a lot of frequency control scheme for laser diode, mainly through the external system to stabilize the frequency of laser diode, the drawback of which is that it is not conducive to system integration. Therefore, this paper proposes a method based on FPGA for controlling the output frequency of the laser diode. The main purpose of the control is to study the frequency characteristics of the laser diode. In this paper, the FPGA chip is used as a micro controller, and combined with PID control algorithm constitute a closed loop control circuit. At the same time, the control algorithm is programmed into the FPGA device, which can maximize the operating speed of control system. For different frequency of the laser, it is only required to modify the control parameters simply, which can be realized the steady control of the light source. Through the test, near the operating temperature of the laser diode, temperature stability is better than +/-0.01°C. As a result, the laser frequency stability can be controlled to 0.1%.

  19. QUANTITATIVE DETECTION OF ENVIRONMENTALLY IMPORTANT DYES USING DIODE LASER/FIBER-OPTIC RAMAN

    EPA Science Inventory

    A compact diode laser/fiber-optic Raman spectrometer is used for quantitative detection of environmentally important dyes. This system is based on diode laser excitation at 782 mm, fiber optic probe technology, an imaging spectrometer, and state-of-the-art scientific CCD camera. ...

  20. Efficient laser performance of a cryogenic Yb:YAG laser pumped by fiber coupled 940 and 969 nm laser diodes

    NASA Astrophysics Data System (ADS)

    Jambunathan, V.; Miura, T.; Těsnohlídková, L.; Lucianetti, A.; Mocek, T.

    2015-01-01

    Laser performance of Yb:YAG at different cryogenic temperatures pumped by a fiber coupled diode laser emitting at 940 and 969 nm were presented. The pump laser diode bandwidth, absorption bandwidth as well as absorption of the laser material at cryogenic temperatures play a vital role on laser performance. The laser threshold decreases and the output power and slope efficiency increase when cooled to cryogenic temperatures.

  1. Efficient high-brightness diode laser modules offer new industrial applications

    NASA Astrophysics Data System (ADS)

    Revermann, Markus; Timmermann, Andre; Meinschien, Jens; Bruns, Peter

    2007-02-01

    We present new developed high power diode laser modules which are performing at outstanding brightness and their applications. The combination of recently designed laser diode bars on passive heat sinks and optimized micro-optics results to laser modules up to 50W out of a 100μm fibre with a 0.22 NA at one single wavelength based on broad area laser bars (BALB) and up to 50W out of 50μm fibre with a 0.22 NA based on single-mode emitter array laser (SEAL) bars. The fibre coupled systems are based on diode lasers with a collimated beam of superior beam data, namely < 10 mm x 10 mm beam diameter (FW1/e2) and < 2mrad x 2mrad divergence (FW1/e2). Such free beam diode lasers deliver 30 W or 60 W output power. The applications for such laser diode modules varies from direct marking, cutting and welding of metals and other materials up to pumping of fibre lasers and amplifiers. Marking speed with up to 30mm/s on stainless steel was observed with 20W laser power and 50μm fibre with a conventional marking setup. Cutting speed of about 1m/min of 0.2mm Kovar sheet was shown with a diode laser module with 50W laser power from a 100μm fibre.

  2. 635nm diode laser biostimulation on cutaneous wounds

    NASA Astrophysics Data System (ADS)

    Solmaz, Hakan; Gülsoy, Murat; Ülgen, Yekta

    2014-05-01

    Biostimulation is still a controversial subject in wound healing studies. The effect of laser depends of not only laser parameters applied but also the physiological state of the target tissue. The aim of this project is to investigate the biostimulation effects of 635nm laser irradiation on the healing processes of cutaneous wounds by means of morphological and histological examinations. 3-4 months old male Wistar Albino rats weighing 330 to 350 gr were used throughout this study. Low-level laser therapy was applied through local irradiation of red light on open skin excision wounds of 5mm in diameter prepared via punch biopsy. Each animal had three identical wounds on their right dorsal part, at which two of them were irradiated with continuous diode laser of 635nm in wavelength, 30mW of power output and two different energy densities of 1 J/cm2 and 3 J/cm2. The third wound was kept as control group and had no irradiation. In order to find out the biostimulation consequences during each step of wound healing, which are inflammation, proliferation and remodeling, wound tissues removed at days 3, 7, 10 and 14 following the laser irradiation are morphologically examined and than prepared for histological examination. Fragments of skin including the margin and neighboring healthy tissue were embedded in paraffin and 6 to 9 um thick sections cut are stained with hematoxylin and eosin. Histological examinations show that 635nm laser irradiation accelerated the healing process of cutaneous wounds while considering the changes of tissue morphology, inflammatory reaction, proliferation of newly formed fibroblasts and formation and deposition of collagen fibers. The data obtained gives rise to examine the effects of two distinct power densities of low-level laser irradiation and compare both with the non-treatment groups at different stages of healing process.

  3. LASER BIOLOGY AND MEDICINE: Medical instruments based on high-power diode and fibre lasers

    NASA Astrophysics Data System (ADS)

    Gapontsev, V. P.; Minaev, V. P.; Savin, V. I.; Samartsev, I. E.

    2002-11-01

    The characteristics and possible applications of scalpels based on diode and fibre lasers emitting at 0.97, 1.06, 1.56, and 1.9 μm, which are produced and developed by the IRE-Polyus Co., are presented. The advantages of such devices and the possibilities for increasing their output power and extending their spectral range are shown.

  4. Portable multiwavelength laser diode source for handheld photoacoustic devices

    NASA Astrophysics Data System (ADS)

    Canal, Celine; Laugustin, Arnaud; Kohl, Andreas; Rabot, Olivier

    2016-04-01

    The ageing population faces today an increase of chronic diseases such as rheumatism/arthritis, cancer and cardio vascular diseases for which appropriate treatments based on a diagnosis at an early-stage of the disease are required. Some imaging techniques are already available in order to get structural information. Within the non-invasive group, ultrasound images are common in these fields of medicine. However, there is a need for a point-of-care device for imaging smaller structures such as blood vessels that cannot be observed with purely ultrasound based devices. Photoacoustics proved to be an attractive candidate. This novel imaging technique combines pulsed laser light for excitation of tissues and an ultrasound transducer as a receptor. Introduction of this technique into the clinic requires to drastically shrink the size and cost of the expensive and bulky nanosecond lasers generally used for light emission. In that context, demonstration of ultra-short pulse emission with highly efficient laser diodes in the near-infrared range has been performed by Quantel, France. A multi-wavelength laser source as small as a hand emitted more than 1 mJ per wavelength with four different wavelengths available in pulses of about 90 ns. Such a laser source can be integrated into high sensitivity photoacoustic handheld systems due to their outstanding electrical-to-optical efficiency of about 25 %. Further work continues to decrease the pulse length as low as 40 ns while increasing the pulse energy to 2 mJ.

  5. Near-infrared laser diodes in monitoring applications

    NASA Astrophysics Data System (ADS)

    Patonay, Gabor; Zen, Jyh-Myng; Czuppon, Tibor

    1992-05-01

    Absorption and fluorescence spectroscopy has proven to be a valuable analytical tool for environmental and process monitoring. Several publications have addressed different spectroscopic applications related to process monitoring. Since most chemicals absorb in the UVIVis part of the spectrum, the majority of laser applications utilize this shorter wavelength region. Nevertheless, the utilization of the longer wavelength part of the electromagnetic spectrum may be advantageous due to its relatively low interference. The environmental and process monitoring applications of this spectral region may be especially advantageous if semiconductor lasers are utilized as light sources. Laser diodes have all the properties of other types of lasers with the added benefits of compactness, low power consumption, low cost and long lifetime. However, to utilize this spectral region for environmental or process monitoring applications, appropriate near-infrared (NIR) absorbing probe molecules need to be employed. These probes may be used to determine analytical properties important for environmental or process monitoring applications, e.g., pH, oxygen concentration, metal ion determinations, solvent hydrophobicity, just to mention a few. These NIR probes may be incorporated into polymers to form a stable probe arrangement for convenient monitoring using semiconductor lasers. The utility can be further enhanced using fiber optics. In this paper the use of MR absorption and fluorescence spectroscopy for monitoring applications will be demonstrated.

  6. Food monitoring based on diode laser gas spectroscopy

    NASA Astrophysics Data System (ADS)

    Lewander, M.; Guan, Z. G.; Persson, L.; Olsson, A.; Svanberg, S.

    2008-11-01

    Food is frequently packed in a controlled environment of gas, in order to extend shelf life. It is of great importance to be able to monitor the status of the packed food to ensure quality. We demonstrate a technique to monitor the gas inside packages non-intrusively by using a laser spectroscopic method in scattering solid materials. The technique named GASMAS (GAs in Scattering Media Absorption Spectroscopy) is based on tunable diode laser absorption spectroscopy and relies on the fact that free gas inside solid materials absorbs much sharper spectrally than the bulk material. Results from time dependent measurements of molecular oxygen and water vapour in packages of minced meat, bake-off bread, and the headspace of a milk carton are presented. We show that the technique allows gas measurements inside the food through the package, and assessment of the integrity of the package.

  7. Side diode pumped ultra-compact Er:glass laser

    NASA Astrophysics Data System (ADS)

    Vitkin, Vladimir V.; Polyakov, Vadim M.; Kharitonov, Artem A.; Buchenkov, Vyacheslav A.; Rodionov, Andrey Y.

    2015-07-01

    We demonstrate side pumped ultra-compact Q-switched Er:glass laser for rangefinding with 1.4 mJ energy at 1.54 um. Laser diode with 75 W power and 5 ms pulse duration was used. Active medium was enveloped with diffuse reflector. Output pulse energy in free-running mode was 27 mJ with a slope efficiency of 12%. Transparent glass-ceramics containing Co2+:MgAl2O4 nanocrystals were used as a passive gate to ensure Q-switching in an operation temperature range and transverse mode selection. The Q-switch mode had steady operation at 1 Hz repetition rate with thermal effects playing no visible role.

  8. Multiple Isotope Magneto Optical Trap from a single diode laser

    NASA Astrophysics Data System (ADS)

    Gomez, Eduardo; Valenzuela, Victor; Hamzeloui, Saeed; Gutierrez, Monica

    2013-05-01

    We present a simple design for a Dual Isotope Magneto Optical Trap. The system requires a single diode laser, a fiber modulator and a tapered amplifier to trap and completely control both 85Rb and 87Rb. We generate all the frequencies needed for trapping both species using the fiber intensity modulator. All the frequencies are amplified simultaneously with the tapered amplifier. The position and power of each frequency is now controlled independently on the RF rather than on the optical side. This introduces an enormous simplification for laser cooling that often requires an acousto-optic modulator for each frequency. The range of frequency changes is much bigger than what is available with acousto-optic modulators since in our case is determined by the modulator bandwidth (10 GHz). Additional isotopes can be simply added by including additional RF frequencies to the modulator and extra beams for other uses can be produced the same way. Support from CONACYT, PROMEP and UASLP.

  9. Gain lever characterization in monolithically integrated diode lasers

    NASA Astrophysics Data System (ADS)

    Pocha, Michael; Bond, Tiziana; Welty, Rebecca; Vernon, Stephen; Kallman, Jeffrey; Behymer, Elaine

    2005-04-01

    Gain Lever, an effect for enhancing amplitude modulation (AM) efficiency in multisection laser diodes1, has been characterized in InGaAs DQW edge emitting lasers that are integrated with passive waveguides. Specifically designed structures which give a range of split ratios from 1:1 to 9:1 have been fabricated and measured to fully characterize the parameter space for operation in the gain lever mode. Additionally the experimental results are compared to a hybrid 3-D simulation involving effective index method (EIM) reduction to 2-D. Gains greater than 6 dB in the AM efficiency can be achieved within the appropriate operating range, but this gain drops rapidly as the parameter range is exceeded. High speed RF modulation with significant gain is, in principle, possible if proper biasing and modulation conditions are used. This phenomenon can also be useful for high-speed digital information transmission.

  10. Discretely tunable multiwavelength diode-pumped Nd:YALO laser

    NASA Astrophysics Data System (ADS)

    Poirier, P.; Hanson, F.

    1996-01-01

    Operation of a moderate-to-high repetition-rate Q-switched quadrupled diode-pumped Nd:YALO laser discretely tunable between 266 and 275 nm is reported. Intracavity frequency doubling of the fundamental yielded 5.4 and 4.4 mJ at 532 and 550 nm, respectively, at a 600-Hz repetition rate. The laser radiation was frequency quadrupled to the UV external to the cavity with an output of 0.28 and 0.24 mJ at 266 and 275 nm, respectively. Astigmatic focal lengths that are due to thermal lensing effects of the Nd:YALO rod in the side-pumping geometry are presented.

  11. Tissue Necrosis Following Diode Laser-Assisted Transcanalicular Dacryocystorhinostomy

    PubMed Central

    McClintic, Scott M.; Yoon, Michael K.; Bidar, Maziar; Dutton, Jonathan J.; Vagefi, M. Reza; Kersten, Robert C.

    2012-01-01

    Advantages of transcanalicular laser-assisted dacryocystorhinostomy (TCDCR) over conventional external and endonasal dacryocystorhinostomy (DCR) have been purported to include decreased operating time, reduced morbidity, enhanced cosmesis, avoidance of general anesthesia, and a shorter recovery time. However, one case of skin necrosis has recently been reported to have occurred following diode laser-assisted TCDCR, and we now report three additional cases that were evaluated by the Ophthalmic Plastic Surgery services at the University of North Carolina and the University of California, San Francisco. Three patients developed full-thickness tissue necrosis over the medial canthus following TCDCR, and two of these patients experienced persistent tissue breakdown at the site following reconstructive repair. PMID:24807803

  12. High power visible diode laser for the treatment of eye diseases by laser coagulation

    NASA Astrophysics Data System (ADS)

    Heinrich, Arne; Hagen, Clemens; Harlander, Maximilian; Nussbaumer, Bernhard

    2015-03-01

    We present a high power visible diode laser enabling a low-cost treatment of eye diseases by laser coagulation, including the two leading causes of blindness worldwide (diabetic retinopathy, age-related macular degeneration) as well as retinopathy of prematurely born children, intraocular tumors and retinal detachment. Laser coagulation requires the exposure of the eye to visible laser light and relies on the high absorption of the retina. The need for treatment is constantly increasing, due to the demographic trend, the increasing average life expectancy and medical care demand in developing countries. The World Health Organization reacts to this demand with global programs like the VISION 2020 "The right to sight" and the following Universal Eye Health within their Global Action Plan (2014-2019). One major point is to motivate companies and research institutes to make eye treatment cheaper and easily accessible. Therefore it becomes capital providing the ophthalmology market with cost competitive, simple and reliable technologies. Our laser is based on the direct second harmonic generation of the light emitted from a tapered laser diode and has already shown reliable optical performance. All components are produced in wafer scale processes and the resulting strong economy of scale results in a price competitive laser. In a broader perspective the technology behind our laser has a huge potential in non-medical applications like welding, cutting, marking and finally laser-illuminated projection.

  13. Multicomponent gas analyzers based on tunable diode lasers

    SciTech Connect

    Stepanov, E.V.; Zyrianov, P.V.; Khusnutdinov, A.N.; Kouznetsov, A.I.; Ponurovskii, Y.Ya.

    1996-12-31

    A family of multicomponent gas analyzers based on tunable diode lasers (TDL) are presented including: an open optical path 3-component gas analyzer for monitoring atmosphere pollution; a 4-gas component analyzer with a multipass cell, a multichannel TDL system with multipass cell and MIR fiber optics delivery, and a multichannel TDL analyzer for breath content gas analysis. A4B6 tunable diode lasers of different spectral region from 4 to 12 micron were used in every channel of the analyzers to obtain atmospheric transmission spectra and to measure concentration of studied gases. Main gaseous atmospheric pollutants like CO, NO, NH{sub 3}, CH{sub 4}, SO{sub 2}, etc. and some of breath gases could be measured at ppb concentration level in real time with these systems depending on customers requirements. The analyzers are driven by IBM compatible PC. The first results on field monitoring tests as well as on their application to human exhalation content analysis and human exposure monitoring are presented.

  14. TOPICAL REVIEW: InGaN-based violet laser diodes

    NASA Astrophysics Data System (ADS)

    Nakamura, S.

    1999-06-01

    High-efficiency light-emitting diodes emitting amber, green, blue and ultraviolet light have been obtained through the use of InGaN active layers instead of GaN active layers. The localized energy states caused by In composition fluctuation in the InGaN active layer seem to be related to the high efficiency of the InGaN-based emitting devices. Long-lifetime violet InGaN multi-quantum-well/GaN/AlGaN separate-confinement heterostructure laser diodes (LDs) were successfully fabricated using epitaxially laterally overgrown GaN by reducing a large number of threading dislocations originating from the interface between GaN and sapphire substrate. The threading dislocations shorten the lifetime of the LDs through an increase of the threshold current density. The LDs with cleaved mirror facets showed an output power as high as 30 mW under room-temperature continuous-wave (CW) operation with a stable fundamental transverse mode. The lifetime of the LDs at a constant output power of 5 mW was estimated to be approximately 3000 h under CW operation at an ambient temperature of 50 °C. These results indicate that these LDs already can be used for many real applications, such as digital versatile disks, laser printers, sensors and exciting light sources as a commercial product with a high output power and a high reliability.

  15. Laser-induced electron source in a vacuum diode

    NASA Astrophysics Data System (ADS)

    Ghera, U.; Boxman, R. L.; Kleinman, H.; Ruschin, S.

    1989-11-01

    Experiments were conducted in which a high-power CO2 TEA laser interacted with metallic cathode in a high-vacuum (10 to the -8th Torr) diode. For power densities lower than 5 x 10 to the 7th W/sq cm, no current was detected. For power densities in the range of 5 x 10 to the 7th to 5 x 10 to the 8th W/sq cm, the Cu cathode emitted a maximum current of 40 mA. At a higher power density level, a circuit-limited current of 8 A was detected. The jump of a few orders of magnitude in the current is attributed to breakdown of the diode gap. The experimental results are similar to those of a triggered vacuum gap, and a thorough comparison is presented in this paper. The influence of the pressure in the vacuum chamber on the current magnitude shows the active role that adsorbed gas molecules have in the initial breakdown. When the cathode material was changed from metal to metal oxide, much lower laser power densities were required to reach the breakdown current region.

  16. Gas analysis of human exhalation by tunable diode laser spectroscopy

    NASA Astrophysics Data System (ADS)

    Stepanov, Eugene V.; Moskalenko, Konstantin L.

    1993-02-01

    Results of the application of a tunable diode laser (TDL) to determining the trace gas components of human exhalation are presented. The analyzer is specially developed to measure both carbon oxides (CO and CO2) in expired air. A few results illuminating possible applications of TDLs in high-sensitivity medical diagnostics have been obtained. For nonsmokers, expired concentrations of CO are slightly higher than those in inhaled air. The specific surplus value seems to be independent of the ambient atmospheric CO content. The surplus CO content increases by more than an order of magnitude just after intensive exercises, e.g., jogging. For smokers, the pharmacokinetic of abundant CO removal from the organism could be investigated by this technique, which provides quick and reliable measurements of smoking status. Breath-holding synchronous measurements of CO and CO2 in exhalation demonstrate behavior that is different with breath-holding time. The method seems useful for the investigation of phenomena such as molecular pulmonary diffusion through the alveolar-capillary membrane and an organism's adaptation to oxygen shortage. Prospects for the development and application of diode laser spectroscopy to trace gas analysis in medicine are also discussed.

  17. New Submount Requirement of Conductively Cooled Laser Diodes for Lidar Applications

    NASA Technical Reports Server (NTRS)

    Mo, S. Y.; Cutler, A. D.; Choi, S. H.; Lee, M. H.; Singh, U. N.

    2000-01-01

    New submount technology is essential for the development of conductively cooled high power diode laser. The simulation and experimental results indicate that thermal conductivity of submount for high power laser-diode must be at least 600 W/m/k or higher for stable operation. We have simulated several theoretical thermal model based on new submount designs and characterized high power diode lasers to determine temperature effects on the performances of laser diodes. The characterization system measures the beam power, output beam profile, temperature distribution, and spectroscopic property of high power diode laser. The characterization system is composed of four main parts: an infrared imaging camera, a CCD camera, a monochromator, and a power meter. Thermal characteristics of two commercial-grade CW 20-W diode laser bars with open heat-sink type were determined with respect to the line shift of emission spectra and beam power stability. The center wavelength of laser emission has a tendency to shift toward longer wavelength as the driving current and heat sink temperature are increased. The increase of heat sink temperature decreases the output power of the laser bar too. Such results lay the guidelines for the design of new submount for high power laser-diodes.

  18. Laser Boronizing of Stainless Steel with Direct Diode Laser

    NASA Astrophysics Data System (ADS)

    Kusuhara, Takayoshi; Morimoto, Junji; Abe, Nobuyuki; Tsukamoto, Masahiro

    Boronizing is a thermo-chemical surface treatment in which boron atoms are diffused into the surface of a work piece to form borides with the base material. When applied to the metallic materials, boronizing provides wear and abrasion resistance comparable to sintered carbides. However conventional boronizing is carried out at temperatures ranging from 800°C to 1050°C and takes from one to several hours. The structure and properties of the base material is influenced considerably by the high temperature and long treatment time. In order to avoid these drawbacks of conventional boronizing, laser-assisted boronizing is investigated which activates the conventional boronizing material and the work piece with a high density laser power. In this study, effect of laser characteristics was examined on the laser boronizing of stainless steel. After laser boronizing, the microstructure of the boride layer was analyzed with an optical microscope, electron probe micro analyser(EPMA) and X-ray diffractometer (XRD). The mechanical properties of borided layer were evaluated using Vickers hardness tester and sand erosion tester. Results showed that the boride layer was composed of NiB, CrB, FeB and Fe2B, and get wear resistance.

  19. Combining femtosecond laser ablation and diode laser welding in lamellar and endothelial corneal transplants

    NASA Astrophysics Data System (ADS)

    Pini, Roberto; Rossi, Francesca; Matteini, Paolo; Ratto, Fulvio; Menabuoni, Luca; Lenzetti, Ivo; Yoo, Sonia H.; Parel, Jean-Marie

    2008-02-01

    Based on our previous clinical experiences in minimally invasive diode laser-induced welding of corneal tissue in penetrating keratoplasty (PK), i.e. full-thickness transplant of the cornea, we combined this technique with the use of a femtosecond laser for applications in lamellar (LK) and endothelial (EK) keratoplasty. In LK, the femtosecond laser was used to prepare donor button and recipient corneal bed; the wound edges were stained with a water solution of Indocyanine Green (ICG) and then irradiated with a diode laser emitting in CW mode to induce stromal welding. Intraoperatory observations and follow-up results up to 6 months indicated the formation of a smooth stromal interface, total absence of edema as well as inflammation, and reduction of post-operative astigmatism, as compared with conventional suturing procedures. In EK the femtosecond laser was used for the preparation of a 100 μm thick, 8.5mm diameter donor corneal endothelium flap. The flap stromal side was stained with ICG. After stripping the recipient Descemet's membrane and endothelium, the donor flap was positioned in the anterior chamber on the inner face of the cornea by an air bubble and secured to the recipient cornea by diode laser pulses delivered by means of a fiberoptic contact probe introduced in the anterior chamber, which produced welding spots of 200 μm diameter. Femtosecond laser sculpturing of the donor cornea provided lamellar and endothelial flaps of preset and constant thickness. Diode laserinduced welding showed a unique potential to permanently secure the donor flap in place, avoiding postoperative displacement and inflammation reaction.

  20. Fiber optic coupling of a microlens conditioned, stacked semiconductor laser diode array

    DOEpatents

    Beach, Raymond J.; Benett, William J.; Mills, Steven T.

    1997-01-01

    The output radiation from the two-dimensional aperture of a semiconductor laser diode array is efficiently coupled into an optical fiber. The two-dimensional aperture is formed by stacking individual laser diode bars on top of another in a "rack and stack" configuration. Coupling into the fiber is then accomplished using individual microlenses to condition the output radiation of the laser diode bars. A lens that matches the divergence properties and wavefront characteristics of the laser light to the fiber optic is used to focus this conditioned radiation into the fiber.

  1. Fiber optic coupling of a microlens conditioned, stacked semiconductor laser diode array

    DOEpatents

    Beach, R.J.; Benett, W.J.; Mills, S.T.

    1997-04-01

    The output radiation from the two-dimensional aperture of a semiconductor laser diode array is efficiently coupled into an optical fiber. The two-dimensional aperture is formed by stacking individual laser diode bars on top of another in a ``rack and stack`` configuration. Coupling into the fiber is then accomplished using individual microlenses to condition the output radiation of the laser diode bars. A lens that matches the divergence properties and wavefront characteristics of the laser light to the fiber optic is used to focus this conditioned radiation into the fiber. 3 figs.

  2. AlGaInN laser diode technology and systems for defence and security applications

    NASA Astrophysics Data System (ADS)

    Najda, Stephen P.; Perlin, Piotr; Suski, Tadek; Marona, Lucja; Boćkowski, Mike; Leszczyński, Mike; Wisniewski, Przemek; Czernecki, Robert; Kucharski, Robert; Targowski, Grzegorz; Watson, Scott; Kelly, Antony E.

    2015-05-01

    The latest developments in AlGaInN laser diode technology are reviewed for defence and security applications such as underwater communications. The AlGaInN material system allows for laser diodes to be fabricated over a very wide range of wavelengths from u.v., ~380nm, to the visible ~530nm, by tuning the indium content of the laser GaInN quantum well. Thus AlGaInN laser diode technology is a key enabler for the development of new disruptive system level applications in displays, telecom, defence and other industries.

  3. Shifted excitation Raman difference spectroscopy using a dual-wavelength DBR diode laser at 785 nm

    NASA Astrophysics Data System (ADS)

    Maiwald, M.; Eppich, B.; Fricke, J.; Ginolas, A.; Bugge, F.; Klehr, A.; Sumpf, B.; Erbert, G.; Tränkle, G.

    2015-03-01

    The application of shifted excitation Raman difference spectroscopy (SERDS) using a dual wavelength distributed Bragg reflector (DBR) diode laser at 785 nm will be presented. Both excitation wavelengths necessary for SERDS provide an optical power of more than 160 mW in continuous wave operation. Raman experiments are carried out and demonstrate the suitability of the excitation light source for SERDS. Moreover, a dual-wavelength master-oscillator power amplifier diode laser system is presented. The diode laser system reaches optical powers larger 750 mW while the spectral properties of the dual-wavelength laser remain unchanged.

  4. Hydrazine Detection with a Tunable Diode Laser Spectrometer

    NASA Technical Reports Server (NTRS)

    Houseman, John; Webster, C. R.; May, R. D.; Anderson, M. S.; Margolis, J. S.; Jackson, Julie R.; Brown, Pamela R.

    1999-01-01

    Several instruments have been developed to measure low concentrations of hydrazine but none completely meet the sensitivity requirements while satisfying additional criteria such as quick response, stable calibration, interference free operation, online operation, reasonable cost, etc. A brief review is presented of the current technology including the electrochemical cell, the ion mobility spectrometer, the mass spectrometer, and the gas chromatograph. A review of the advantages and disadvantages of these instruments are presented here. The review also includes commercially unavailable technology such as the electronic nose and the Tunable Diode Laser (TDL) IR Spectrometer. It was found that the TDL could meet the majority of these criteria including fast response, minimum maintenance, portability, and reasonable cost. An experiment was conducted to demonstrate the feasibility of such a system using an existing (non-portable) instrument. A lead-salt tunable diode laser, cooled to 85 degrees Kelvin was used to record direct absorption and second-derivative spectra of Hydrazine at several pressures to study the sensitivity to low levels of Hydrazine. Spectra of NH3 and CO2 were used for wavelength identification of the scanned region. With a pathlength of 80 m, detection sensitivities of about 1 ppb were achieved for hydrazine in dry nitrogen at a cell pressure of 100 mbar. For spectroscopic detection of Hydrazine, spectral regions including strong Ammonia or Carbon Dioxide lines must be avoided. Strong Hydrazine absorption features were identified at 940/cm showing minimal contribution from Ammonia interferences as suitable candidates for Hydrazine gas detection. For the studies reported here, the particular laser diode could only cover the narrow regions near 962/cm and 965/cm where strong Ammonia interferences were expected. However, the high resolution (0.001/cm) of the TDL spectrometer allowed individual lines of Hydrazine to be identified away from

  5. High-power diode lasers for optical communications applications

    NASA Technical Reports Server (NTRS)

    Carlin, D. B.; Goldstein, B.; Channin, D. J.

    1985-01-01

    High-power, single-mode, double-heterojunction AlGaAs diode lasers are being developed to meet source requirements for both fiber optic local area network and free space communications systems. An individual device, based on the channeled-substrate-planar (CSP) structure, has yielded single spatial and longitudinal mode outputs of up to 90 mW CW, and has maintained a single spatial mode to 150 mW CW. Phase-locked arrays of closely spaced index-guided lasers have been designed and fabricated with the aim of multiplying the outputs of the individual devices to even higher power levels in a stable, single-lobe, anastigmatic beam. The optical modes of the lasers in such arrays can couple together in such a way that they appear to be emanating from a single source, and can therefore be efficiently coupled into optical communications systems. This paper will review the state of high-power laser technology and discuss the communication system implications of these devices.

  6. Interference comparator for laser diode wavelength and wavelength instability measurement

    NASA Astrophysics Data System (ADS)

    Dobosz, Marek; KoŻuchowski, Mariusz

    2016-04-01

    Method and construction of a setup, which allows measuring the wavelength and wavelength instability of the light emitted by a laser diode (or a laser light source with a limited time coherence in general), is presented. The system is based on Twyman-Green interferometer configuration. Proportions of phases of the tested and reference laser's interference fringe obtained for a set optical path difference are a measure of the unknown wavelength. Optical path difference in interferometer is stabilized. The interferometric comparison is performed in vacuum chamber. The techniques of accurate fringe phase measurements are proposed. The obtained relative standard uncertainty of wavelength evaluation in the tested setup is about 2.5 ṡ 10-8. Uncertainty of wavelength instability measurement is an order of magnitude better. Measurement range of the current setup is from 500 nm to 650 nm. The proposed technique allows high accuracy wavelength measurement of middle or low coherence sources of light. In case of the enlarged and complex frequency distribution of the laser, the evaluated wavelength can act as the length master in interferometer for displacement measurement.

  7. Interference comparator for laser diode wavelength and wavelength instability measurement.

    PubMed

    Dobosz, Marek; Kożuchowski, Mariusz

    2016-04-01

    Method and construction of a setup, which allows measuring the wavelength and wavelength instability of the light emitted by a laser diode (or a laser light source with a limited time coherence in general), is presented. The system is based on Twyman-Green interferometer configuration. Proportions of phases of the tested and reference laser's interference fringe obtained for a set optical path difference are a measure of the unknown wavelength. Optical path difference in interferometer is stabilized. The interferometric comparison is performed in vacuum chamber. The techniques of accurate fringe phase measurements are proposed. The obtained relative standard uncertainty of wavelength evaluation in the tested setup is about 2.5 ⋅ 10(-8). Uncertainty of wavelength instability measurement is an order of magnitude better. Measurement range of the current setup is from 500 nm to 650 nm. The proposed technique allows high accuracy wavelength measurement of middle or low coherence sources of light. In case of the enlarged and complex frequency distribution of the laser, the evaluated wavelength can act as the length master in interferometer for displacement measurement. PMID:27131662

  8. Low-threshold short-cavity diode laser for a miniature atomic clock

    SciTech Connect

    Kargapol'tsev, Sergei V; Velichansky, Vladimir L; Vasil'ev, V V; Kobyakova, M Sh; Morozyuk, A V; Shiryaeva, N V; Konyaev, V P

    2009-06-30

    Short-cavity diode lasers (SCDLs) emitting at the 894-nm D{sub 1} line of caesium are developed. Low threshold currents and power consumption will make it possible to use these lasers in chip-size atomic clocks (CSACs) and magnetometers. The SCDL parameters are comparable with the parameters of surface-emitting lasers. (lasers)

  9. High power 2 {mu}m diode-pumped Tm:YAG laser

    SciTech Connect

    Beach, R.J.; Sutton, S.B.; Honea, E.C.; Skidmore, J.A.; Emanuel, M.A.

    1996-01-01

    Using a scaleable diode end-pumping technology developed at LLNL, we have demonstrated a compact Tm:YAG laser capable of generating more than 50 W of cw 2 {mu}m laser output power. The design and operational characteristics of this laser, which was built originally for use in assessing laser surgical techniques, are discussed.

  10. Functional possibilities for forming different inverse population distributions in diode-side-pumped laser heads

    SciTech Connect

    Grechin, S G; Nikolaev, P P; Sharandin, E A

    2014-10-31

    The functional possibilities of diode-side-pumped laser heads of solid-state lasers for forming inverse population distributions of different types are analysed. The invariants determining the relationship between the laser head parameters upon scaling are found. The results of comparative experimental studies are presented. (lasers)

  11. Laser-diode pumped 40-W Yb:YAG ceramic laser.

    PubMed

    Hao, Qiang; Li, Wenxue; Pan, Haifeng; Zhang, Xiaoyi; Jiang, Benxue; Pan, Yubai; Zeng, Heping

    2009-09-28

    We demonstrated a high-power continuous-wave (CW) polycrystalline Yb:YAG ceramic laser pumped by fiber-pigtailed laser diode at 968 nm with 400 mum fiber core. The Yb:YAG ceramic laser performance was compared for different Yb(3+) ion concentrations in the ceramics by using a conventional end-pump laser cavity consisting of two flat mirrors with output couplers of different transmissions. A CW laser output of 40 W average power with M(2) factor of 5.8 was obtained with 5 mol% Yb concentration under 120 W incident pump power. This is to the best of our knowledge the highest output power in end-pumped bulk Yb:YAG ceramic laser. PMID:19907559

  12. Multi-kW cw fiber oscillator pumped by wavelength stabilized fiber coupled diode lasers

    NASA Astrophysics Data System (ADS)

    Becker, Frank; Neumann, Benjamin; Winkelmann, Lutz; Belke, Steffen; Ruppik, Stefan; Hefter, Ulrich; Köhler, Bernd; Wolf, Paul; Biesenbach, Jens

    2013-02-01

    High power Yb doped fiber laser sources are beside CO2- and disk lasers one of the working horses of industrial laser applications. Due to their inherently given robustness, scalability and high efficiency, fiber laser sources are best suited to fulfill the requirements of modern industrial laser applications in terms of power and beam quality. Pumping Yb doped single-mode fiber lasers at 976nm is very efficient. Thus, high power levels can be realized avoiding limiting nonlinear effects like SRS. However the absorption band of Yb doped glass around 976nm is very narrow. Therefore, one has to consider the wavelength shift of the diode lasers used for pumping. The output spectrum of passively cooled diode lasers is mainly defined by the applied current and by the heat sink temperature. Furthermore the overall emission line width of a high power pump source is dominated by the large number of needed diode laser emitters, each producing an individual spectrum. Even though it is possible to operate multi-kW cw single-mode fiber lasers with free running diode laser pumps, wavelength stabilizing techniques for diode lasers (e.g. volume holographic gratings, VHG) can be utilized in future fiber laser sources to increase the output power level while keeping the energy consumption constant. To clarify the benefits of wavelength stabilized diode lasers with integrated VHG for wavelength locking the performance of a dual side pumped fiber oscillator is discussed in this article. For comparison, different pumping configurations consisting of stabilized and free-running diode lasers are presented.

  13. Diode-laser-pumped Nd:YAG laser injection seeding system.

    PubMed

    Schmitt, R L; Rahn, L A

    1986-03-01

    We have designed and tested a compact injection seeding system consisting of a diode-laser-pumped Nd:YAG master oscillator and a permanent-magnet Faraday isolator. With active resonator frequency stabilization, this system permits highly reliable single-axial-mode operation of a Q-switched Nd:YAG laser over a period of hours. The system is capable of injection seeding both stable and unstable resonator designs and is suitable for injection seeding commercial lasers with only minor modifications. PMID:18231224

  14. The Effect of Diode Laser With Different Parameters on Root Fracture During Irrigation Procedure.

    PubMed

    Karataş, Ertuğrul; Arslan, Hakan; Topçuoğlu, Hüseyin Sinan; Yılmaz, Cenk Burak; Yeter, Kübra Yesildal; Ayrancı, Leyla Benan

    2016-06-01

    The aim of this study is to compare the effect of a single diode laser application and agitation of EDTA with diode laser with different parameters at different time intervals on root fracture. Ninety mandibular incisors were instrumented except the negative control group. The specimens were divided randomly into 10 groups according to final irrigation procedure: (G1) non-instrumented; (G2) distilled water; (G3) 15% EDTA; (G4) ultrasonically agitated EDTA; (G5) single 1.5W/100 Hz Diode laser; (G6) single 3W/100 Hz Diode laser; (G7) 1.5W/100 Hz Diode laser agitation of EDTA for 20 s; (G8) 1.5W/100 Hz Diode laser agitation of EDTA for 40 s; (G9) 3W/100 Hz Diode laser agitation of EDTA for 20 s; and (G10) 3W/100 Hz Diode laser agitation of EDTA for 40 s. The specimens were filled, mounted in acrylic resin, and compression strength test was performed on each specimen. Statistical analysis was carried out using one way ANOVA and Tukey's post hoc tests (P = 0.05). The statistical analysis revealed that there were statistically significant differences among the groups (P < 0.05). Laser-agitated irrigation with a 3W/100 Hz Diode laser for both 20 s and 40 s decreased the fracture resistance of teeth. PMID:26582280

  15. Ultralow detection limits for an organic dye determined by fluorescence spectroscopy with laser diode excitation

    SciTech Connect

    Johnson, P.A.; Barber, T.E.; Smith, B.W.; Winefordner, J.D. )

    1989-04-15

    Fluorescence of IR-140, a laser dye in methanol solution, is excited by a semiconductor laser diode. Analytical figures of merit are compared for three different instrumental configurations, with the dye measured in a cuvette, a liquid jet, and a compact instrument. The best limit of detection, 46,000 molecules, was achieved with a liquid jet. Linear dynamic range was 6 orders of magnitude. The laser diode operates in the near-infrared region, resulting in low background fluorescence.

  16. An experimental study of low-frequency amplitude noise in a fibre Bragg grating laser diode

    SciTech Connect

    Zholnerov, V S; Ivanov, A V; Kurnosov, V D; Kurnosov, K V; Romantsevich, V I; Chernov, R V

    2013-09-30

    We have studied the amplitude noise in a fibre Bragg grating laser diode. It has been shown that discontinuities in noise characteristics correlate with those in the power – current and spectral characteristics of the laser diode, whereas the noise characteristics of the pump source have no such discontinuities. The highest noise level has been observed at pump currents corresponding to concurrent generation of two longitudinal modes. (lasers)

  17. Wide-aperture laser diode array in the external V-shaped cavity

    SciTech Connect

    Svetikov, V V; Nurligareev, D Kh

    2014-09-30

    The operation of a wide-aperture laser diode array with the radiation wavelength 980 nm in external V-shaped symmetric and asymmetric cavities is experimentally studied. The regimes of stable oscillation are studied as functions of the feedback beam direction. The spectra and the intensity distribution of radiation in the far zone are presented for the laser diode in symmetric and asymmetric cavities. Tuning of the radiation wavelength is demonstrated using the Littman geometry in the asymmetric cavity. (lasers)

  18. Mode locking of diode- and flashlamp-pumped Nd:YAG lasers using semiconductor saturable absorbers

    NASA Astrophysics Data System (ADS)

    Dombrovsky, Andrej; Kubecek, Vaclav; Zvonicek, K.; Diels, Jean-Claude M.; Stintz, Andreas

    2003-07-01

    Operation of laser diode and flash lamp pumped Nd:YAG lasers mode locked with two different types of semiconductor saturable absorbers is reported. In the first type that is used mainly in diode pumped systems the absorber layers are integrated on highly reflective Bragg mirror. The second type is for use in transmission mode inside the resonator. Different design of semiconductor elements, pumping geometries and resonator configurations were investigated and characteristics of laser operation in mode-locked regime are presented.

  19. Unveiling laser diode "fossil" and the dynamic analysis for heliotropic growth of catastrophic optical damage in high power laser diodes.

    PubMed

    Zhang, Qiang; Xiong, Yihan; An, Haiyan; Boucke, Konstantin; Treusch, Georg

    2016-01-01

    Taking advantage of robust facet passivation, we unveil a laser "fossil" buried within a broad area laser diode (LD) cavity when the LD was damaged by applying a high current. For the first time, novel physical phenomena have been observed at these dramatically elevated energy densities within the nanoscale LD waveguide. The observation of the laser "fossil" is interpreted with different mechanisms, including: the origination of bulk catastrophic optical damage (COD) due to locally high energy densities, heliotropic COD growth, solid-liquid-gas phase transformations, strong longitudinal phonon cooling effect on the molten COD wave front, and the formation of patterns due to laser lateral modes. For the first time the COD propagation is analyzed temporally by an acoustic phonon bouncing model and the COD velocity is extrapolated to be exponentially decreasing from more than 800 μm/μs to a few μm/μs within a 20 μs time period as the energy density dissipates. PMID:26740303

  20. High Power Diode Pumped 1.06 Micron Solid State Laser

    NASA Astrophysics Data System (ADS)

    Arvind, Mukundarajan A.; Martin, Dan W.; Osterhage, R. J.

    1989-07-01

    Diode pumped solid state lasers have been attracting significant interest in recent years due to advances in high power semiconductor diode lasers. They offer considerable advantages over flashlamp pumped lasers such as compact size, high efficiency, lower heat dissipation and solid-state reliability. In this paper, we report on the results of a Nd:YAG laser, transverse pumped by diode laser arrays. We have measured an output power of 1.14 Watts at 1.06 microns with a laser diode power consumption of 40 Watts. This represents the highest reported electrical efficiency (2.85%) for a transverse pumped, CW, TEM00 laser. The diode arrays were selected and tuned to emit at wavelengths close to the peak neodymium absorption line at 0.808 microns with Peltier coolers. Two diode laser bars side pumped a 20 mm long, 1.5 mm diameter Nd:YAG laser rod. The optical cavity is 13.8 cm long consisting of a high reflectivity mirror and a 95% reflectivity output mirror. The output beam divergence was measured to be near diffraction limited at 1.4 milliradians, and the beam diameter was 1 mm.

  1. Improved performance of high average power semiconductor arrays for applications in diode pumped solid state lasers

    SciTech Connect

    Beach, R.; Emanuel, M.; Benett, W.; Freitas, B.; Ciarlo, D.; Carlson, N.; Sutton, S.; Skidmore, J.; Solarz, R.

    1994-01-01

    The average power performance capability of semiconductor diode laser arrays has improved dramatically over the past several years. These performance improvements, combined with cost reductions pursued by LLNL and others in the fabrication and packaging of diode lasers, have continued to reduce the price per average watt of laser diode radiation. Presently, we are at the point where the manufacturers of commercial high average power solid state laser systems used in material processing applications can now seriously consider the replacement of their flashlamp pumps with laser diode pump sources. Additionally, a low cost technique developed and demonstrated at LLNL for optically conditioning the output radiation of diode laser arrays has enabled a new and scalable average power diode-end-pumping architecture that can be simply implemented in diode pumped solid state laser systems (DPSSL`s). This development allows the high average power DPSSL designer to look beyond the Nd ion for the first time. Along with high average power DPSSL`s which are appropriate for material processing applications, low and intermediate average power DPSSL`s are now realizable at low enough costs to be attractive for use in many medical, electronic, and lithographic applications.

  2. High peak power diode stacks for high energy lasers

    NASA Astrophysics Data System (ADS)

    Negoita, Viorel C.; Vethake, Thilo; Jiang, John; Roff, Robert; Shih, Ming; Duck, Richard; Bauer, Marc; Mite, Roberto; Boucke, Konstantin; Treusch, Georg

    2015-02-01

    High energy solid state lasers are being developed for fusion experiments and other research applications where high energy per pulse is required but the repetition rate is rather low, around 10Hz. We report our results on high peak power diode laser stacks used as optical pumps for these lasers. The stacks are based on 10 mm bars with 4 mm cavity length and 55% fill factor, with peak power exceeding 500 W per bar. These bars are stacked and mounted on a cooler which provides backside cooling and electrical insulation. Currently we mount 25 bars per cooler for a nominal peak power of 12.5 kW, but in principle the mounting scheme can be scaled to a different number of devices depending on the application. Pretesting of these bars before soldering on the cooler enables us to select devices with similar wavelength and thus we maintain tight control of the spectral width (FWHM less than 6 nm). Fine adjustments of the centroid wavelength can be done by means of temperature of the cooling fluid or bias current. The available wavelength range spans from 880 nm to 1000 nm, and the wavelength of the entire assembly of stacks can be controlled to within 0.5 nm of the target value, which makes these stacks suitable for pumping a variety of gain media. The devices are fast axis collimated, with over 95% power being collimated in 6 mrad (full angle). The slow axis divergence is 9° (full angle) for 95% power content.

  3. Aluminium surface treatment with ceramic phases using diode laser

    NASA Astrophysics Data System (ADS)

    Labisz, K.; Tański, T.; Brytan, Z.; Pakieła, W.; Wiśniowski, M.

    2016-07-01

    Ceramic particles powder feeding into surface layer of engineering metal alloy is a well-known and widely used technique. New approach into the topic is to obtain finely distributed nano-sized particles involved in the aluminium matrix using the traditional laser technology. In this paper are presented results of microstructure investigation of cast aluminium-silicon-copper alloys surface layer after heat treatment and alloying with ceramic carbides of WC and ZrO2 using high-power diode laser. The surface layer was specially prepared for the reason of reducing the reflectivity, which is the main problem in the up-to-date metal matrix composites production. With scanning electron microscopy, it was possible to determine the deformation process and distribution of WC and ZrO2 ceramic powder phase. Structure of the surface after laser treatment changes, revealing three zones—remelting zone, heat-affected zone and transition zone placed over the Al substrate. The structural changes of ceramic powder, its distribution and morphology as well as microstructure of the matrix material influence on functional properties, especially wear resistance and hardness of the achieved layer, were investigated.

  4. Ash characteristics in controlled diode laser pyrolysis of chlorinated rubber

    NASA Astrophysics Data System (ADS)

    Peligrad, A. A.; Schmidt, M. J. J.; Li, L.; Spencer, J. T.

    2000-02-01

    This paper describes the effects of 60 W High Power Diode Laser (HPDL) beams on the removal of chlorinated rubber (CR) paint from concrete surfaces and the ash particles generated from this process. The physical characteristics, including shape and size distribution of the removed and collected airborne CR particles, down to a size of around 1 μm in diameter, were determined using optical microscopy and image analysis. The shape of the particles observed was highly irregular, displaying no symmetry. The size distribution of the collected particles was found to range between 1-2000 μm, with the maximum concentration being found between 29 and 60 μm. The chemical characteristics of the CR ash particles were investigated by means of ESEM and EDX techniques. From a comparative analysis, it was found that the concentration of chlorine within the CR material was significantly reduced after HPDL treatment. This, together with DTA/TGA results indicated a combustive degradation of the CR polymer through the interaction with the process gas, oxygen, and the laser irradiation. Also, a strong correlation between laser power and average particle sizes has been found, with higher powers generally producing larger particle sizes. Opposite effects have been found by changing the oxygen flow rate, with higher oxygen flow producing, on average, smaller particles. An interpretation of the combustion process, as well as a brief discussion on operational safety and environmental impact of the products is attempted.

  5. Posthaste Outgrow of Lip Pyogenic Granuloma after Diode Laser Removal

    PubMed Central

    Asnaashari, Mohammad; Bigom-Taheri, Jamile; Mehdipoor, Maesoome; Bakhshi, Mahin

    2014-01-01

    Introduction: Pyogenic granuloma (PG) is one of the inflammatory hyperplasia seen in the oral cavity. It is a reactional response to minor trauma or chronic irritation and also might be related to hormonal changes. Rarely, PG occurs extragingivally.The most common treatment of PG is surgical excision but alternative approaches such as laser excision have also been proposed. Case report: Herein, we present a case of lip pyogenic granuloma in a 15-year-old male whom had been under orthodontic treatment. The lesion was first excised with diode laser as a conservative method, but the lesion had immediately recurred and was excised with surgical blade as the traditional method. No recurrence or scarring was observed in 6 months follow-up. Results and conclusion: Although the use of laser as modern medicine offers a new tool for treatment of oral lesions, scalpel (blade) surgical excision still seems to be the successful treatment of choice in minimizing the recurrence of lesion especially when exacerbating factors such as hormonal imbalances exist. PMID:25653806

  6. High-average-power diode-pumped Yb: YAG lasers

    SciTech Connect

    Avizonis, P V; Beach, R; Bibeau, C M; Emanuel, M A; Harris, D G; Honea, E C; Monroe, R S; Payne, S A; Skidmore, J A; Sutton, S B

    1999-10-01

    A scaleable diode end-pumping technology for high-average-power slab and rod lasers has been under development for the past several years at Lawrence Livermore National Laboratory (LLNL). This technology has particular application to high average power Yb:YAG lasers that utilize a rod configured gain element. Previously, this rod configured approach has achieved average output powers in a single 5 cm long by 2 mm diameter Yb:YAG rod of 430 W cw and 280 W q-switched. High beam quality (M{sup 2} = 2.4) q-switched operation has also been demonstrated at over 180 W of average output power. More recently, using a dual rod configuration consisting of two, 5 cm long by 2 mm diameter laser rods with birefringence compensation, we have achieved 1080 W of cw output with an M{sup 2} value of 13.5 at an optical-to-optical conversion efficiency of 27.5%. With the same dual rod laser operated in a q-switched mode, we have also demonstrated 532 W of average power with an M{sup 2} < 2.5 at 17% optical-to-optical conversion efficiency. These q-switched results were obtained at a 10 kHz repetition rate and resulted in 77 nsec pulse durations. These improved levels of operational performance have been achieved as a result of technology advancements made in several areas that will be covered in this manuscript. These enhancements to our architecture include: (1) Hollow lens ducts that enable the use of advanced cavity architectures permitting birefringence compensation and the ability to run in large aperture-filling near-diffraction-limited modes. (2) Compound laser rods with flanged-nonabsorbing-endcaps fabricated by diffusion bonding. (3) Techniques for suppressing amplified spontaneous emission (ASE) and parasitics in the polished barrel rods.

  7. Temperature issues with white laser diodes, calculation and approach for new packages

    NASA Astrophysics Data System (ADS)

    Lachmayer, Roland; Kloppenburg, Gerolf; Stephan, Serge

    2015-01-01

    Bright white light sources are of significant importance for automotive front lighting systems. Today's upper class systems mainly use HID or LED light sources. As a further step laser diode based systems offer a high luminance, efficiency and allow the realization of new dynamic and adaptive light functions and styling concepts. The use of white laser diode systems in automotive applications is still limited to laboratories and prototypes even though announcements of laser based front lighting systems have been made. But the environment conditions for vehicles and other industry sectors differ from laboratory conditions. Therefor a model of the system's thermal behavior is set up. The power loss of a laser diode is transported as thermal flux from the junction layer to the diode's case and on to the environment. Therefor its optical power is limited by the maximum junction temperature (for blue diodes typically 125 - 150 °C), the environment temperature and the diode's packaging with its thermal resistances. In a car's headlamp the environment temperature can reach up to 80 °C. While the difference between allowed case temperature and environment temperature is getting small or negative the relevant heat flux also becomes small or negative. In early stages of LED development similar challenges had to be solved. Adapting LED packages to the conditions in a vehicle environment lead to today's efficient and bright headlights. In this paper the need to transfer these results to laser diodes is shown by calculating the diodes lifetimes based on the presented model.

  8. Optical leak detection of oxygen using IR-laser diodes

    NASA Technical Reports Server (NTRS)

    Disimile, P. J.; Fox, C.; Toy, N.

    1991-01-01

    The ability to accurately measure the concentration of gaseous oxygen and its corresponding flow rate is becoming of greater importance. The technique being presented is based on the principal of light attenuation due to the absorption of radiation by the A-band of oxygen which is located in the 759-770 nm wavelength range. With an ability to measure the change in the light transmission to 0.05 percent, a sensitive optical leak detection system which has a rapid time response is possible. In this research program, the application of laser diode technology and its ability to be temperature tuned to a selected oxygen absorption spectral peak has allowed oxygen concentrations as low as 16,000 ppm to be detected.

  9. Tunable Diode Laser Applications To Cigarette Smoke Analysis

    NASA Astrophysics Data System (ADS)

    Vilcins, Gunars; Harward, Charles N.; Parrish, Milton E.; Forrest, Gary T.

    1983-11-01

    High resolution infrared tunable diode laser spectroscopy (TDL) has been applied to the study of cigarette smoke for qualitative and quantitative determinations involved in tobacco blend and cigarette filter developments. As examples of the different types of application of this work, several TDL studies are presented. The measurements of smoke components on a puff-by-puff basis in confined sample chambers and flowing streams were used to study the smoke component deliveries and the effects of filter dilution. The study of isotopes generated during combustion of chemically treated tobaccos was another application of the TDL system to complex gas mixtures without prior separation of compo-nents. The application of the TDL to the study of cigarette filters and smoke delivery simultaneously was demonstrated by using two well resolved absorption lines of two different gases which occur on a single TDL wavelength scan.

  10. Measurements of Trace Gases Using a Tunable Diode Laser

    NASA Technical Reports Server (NTRS)

    Jost, Hans-Juerg

    2005-01-01

    This report is the final report for "Measurements of Trace Gases Using a Tunable Diode Laser." The tasks outlined in the proposal are listed below with a brief comment. The publications and the conference presentations are listed. Finally, the important publications are attached. The Cooperative Agreement made possible a research effort to produce high- precision and high-accuracy in-situ measurements of carbon monoxide, methane and nitrous oxide on the WB-57 during the CRYSTAL-FACE and pre-AVE field campaigns and to analyze these measurements. These measurements of CO and CH4 were of utmost importance to studies of the radiative effects of clouds. Some important results of the CRYSTAL-FACE program were contained in two scientific papers (attached). This Cooperative Agreement allowed the participation of the Argus instrument in the program and the analysis of the data.

  11. Laser diode with thermal conducting, current confining film

    NASA Technical Reports Server (NTRS)

    Hawrylo, Frank Z. (Inventor)

    1980-01-01

    A laser diode formed of a rectangular parallelopiped body of single crystalline semiconductor material includes regions of opposite conductivity type indium phosphide extending to opposite surfaces of the body. Within the body is a PN junction at which light can be generated. A stripe of a conductive material is on the surface of the body to which the P type region extends and forms an ohmic contact with the P type region. The stripe is spaced from the side surfaces of the body and extends to the end surfaces of the body. A film of germanium is on the portions of the surface of the P type region which is not covered by the conductive stripe. The germanium film serves to conduct heat from the body and forms a blocking junction with the P type region so as to confine the current through the body, across the light generating PN junction, away from the side surfaces of the body.

  12. Microgravity Diode Laser Spectroscopy Measurements in a Reacting Vortex Ring

    NASA Technical Reports Server (NTRS)

    Chen, Shin-Juh; Dahm, Werner J. A.; Silver, Joel A.; Piltch, Nancy D.; VanderWal, R. (Technical Monitor)

    2001-01-01

    The technique of Diode Laser Spectroscopy (DLS) with wavelength modulation is utilized to measure the concentration of methane in reacting vortex rings under microgravity conditions. From the measured concentration of methane, other major species such as water, carbon dioxide, nitrogen, and oxygen can be easily computed under the assumption of equilibrium chemistry with an iterative method called ITAC (Iterative Temperature with Assumed Chemistry). The conserved scalar approach in modelling the coupling between fluid dynamics and combustion is utilized to represent the unknown variables in terms of the mixture fraction and scalar dissipation rate in conjunction with ITAC. Post-processing of the DLS and the method used to compute the species concentration are discussed. From the flame luminosity results, ring circulation appears to increase the fuel consumption rate inside the reacting vortex ring and the flame height for cases with similar fuel volumes but different ring circulations. The concentrations of methane, water, and carbon dioxide agree well with available results from numerical simulations.

  13. Linear laser diode arrays for improvement in optical disk recording

    NASA Technical Reports Server (NTRS)

    Alphonse, G. A.; Carlin, D. B.; Connolly, J. C.

    1990-01-01

    The development of individually addressable laser diode arrays for multitrack magneto-optic recorders for space stations is discussed. Three multi-element channeled substrate planar (CSP) arrays with output power greater than 30 mW with linear light vs current characteristics and stable single mode spectra were delivered to NASA. These devices have been used to demonstrate for the first time the simultaneous recording of eight data tracks on a 14-inch magneto-optic erasable disk. The yield of these devices is low, mainly due to non-uniformities inherent to the LPE growth that was used to fabricate them. The authors have recently developed the inverted CSP, based on the much more uniform MOCVD growth techniques, and have made low threshold quantum well arrays requiring about three times less current than the CSP to deliver 30 mW CW in a single spatial mode. The inverted CSP is very promising for use in space flight recorder applications.

  14. Manufacturing experience in reducing environmental induced failures of laser diodes

    SciTech Connect

    Jollay, D.

    1996-12-31

    Packaged life testing of laser diodes revealed a dramatic degradation of product lifetime. Failure analysis revealed the presence of carbon based compounds deposited on the emission region causing catastrophic failure. This phenomenon was limited to packaged product. Testing was begun to identify the source, understand the mechanism, and initiate corrective action. Analysis revealed that the epoxy used in assembly was the dominate source of carbon. Contaminated epoxy had been introduced into production by a material batch change at the vendor. It was also learned that deposition only occured in the dry, oxygen free atmosphere of a hermetically sealed package. It was necessary to develop incoming test procedures and process monitoring to ensure that material of acceptable quality was used. This paper will discuss test methods and results obtained in controlling this failure mechanism.

  15. Liquid metal heat sink for high-power laser diodes

    NASA Astrophysics Data System (ADS)

    Vetrovec, John; Litt, Amardeep S.; Copeland, Drew A.; Junghans, Jeremy; Durkee, Roger

    2013-02-01

    We report on the development of a novel, ultra-low thermal resistance active heat sink (AHS) for thermal management of high-power laser diodes (HPLD) and other electronic and photonic components. AHS uses a liquid metal coolant flowing at high speed in a miniature closed and sealed loop. The liquid metal coolant receives waste heat from an HPLD at high flux and transfers it at much reduced flux to environment, primary coolant fluid, heat pipe, or structure. Liquid metal flow is maintained electromagnetically without any moving parts. Velocity of liquid metal flow can be controlled electronically, thus allowing for temperature control of HPLD wavelength. This feature also enables operation at a stable wavelength over a broad range of ambient conditions. Results from testing an HPLD cooled by AHS are presented.

  16. Laser remelting of Ti6AL4V using high power diode laser

    NASA Astrophysics Data System (ADS)

    Amaya-Vázquez, M. R.; Sánchez-Amaya, J. M.; Boukha, Z.; El Amrani, K.; Botana, F. J.

    2012-04-01

    Titanium alloys present excellent mechanical and corrosion properties, being widely employed in different industries such as medical, aerospace, automotive, petrochemical, nuclear and power generation, etc. Ti6Al4V is the α-β alloy most employed in industry. The modification of its properties can be achieved with convectional heat treatments and/or with laser processing. Laser remelting (LR) is a technology applied to Ti6Al4V by other authors with excimer and Nd-Yag laser with pure argon shielding gas to prevent risk of oxidation. In the present contribution, laser remelting has been applied for the first time to Ti6Al4V with a high power diode laser (with pure argon as shielding gas). Results showed that remelted samples (with medium energy densities) have higher microhardness and better corrosion resistance than Ti6Al4V base metal.

  17. High-performance monolithic surface emitting GaAs/AlGaAs laser diode arrays

    NASA Astrophysics Data System (ADS)

    Groussin, Bernard; Pitard, Francois; Volluet, Gerard; Carriere, Claude

    1994-09-01

    This paper describes recent progress in the development of more advance laser diode pump source: 'Monolithic Surface Emitting Laser Diode' (MOSEL). In this structure, the linear bar arrays are epitaxially grown on an engraved substrate between etched deflection mirrors adjacent to the laser facets. The laser diode structure grown by MOCVD technique is a single quantum well graded index active region (SQW/GRINSCH). A specific process has been designed to have cleaved laser diode facets. Monolithic elements of 0.1 cm(superscript 2) have been designed and mounted. The quasi-CW operation gives over 100 W of optical power or a QCW power density of 1 KW/cm(superscript 2). A compact assembly of 10 similar elements gives an optical power of 1 KW QCW. CW operation have been also tested up to 150 W CW/cm(superscript 2).

  18. Optical phase dynamics in mutually coupled diode laser systems exhibiting power synchronization

    NASA Astrophysics Data System (ADS)

    Pal, Vishwa; Prasad, Awadhesh; Ghosh, R.

    2011-12-01

    We probe the physical mechanism behind the known phenomenon of power synchronization of two diode lasers that are mutually coupled via their delayed optical fields. In a diode laser, the amplitude and the phase of the optical field are coupled by the so-called linewidth enhancement factor, α. In this work, we explore the role of optical phases of the electric fields in amplitude (and hence power) synchronization through α in such mutually delay-coupled diode laser systems. Our numerical results show that the synchronization of optical phases drives the powers of lasers to synchronized death regimes. We also find that as α varies for different diode lasers, the system goes through a sequence of in-phase amplitude-death states. Within the windows between successive amplitude-death regions, the cross-correlation between the field amplitudes exhibits a universal power-law behaviour with respect to α.

  19. ACTIVE MEDIA. LASERS: Study of a Nd3+:KGW crystal laser transversely pumped by laser diode bars

    NASA Astrophysics Data System (ADS)

    Abazadze, Aleksandr Yu; Zverev, Georgii M.; Kolbatskov, Yurii M.; Ustimenko, N. S.

    2004-01-01

    A Nd3+:KGW crystal laser transversely pumped by laser diode bars is studied experimentally. The optimisation of the laser parameters provided the maximum slope efficiency of ~50 % at 1.067 μm in the free running regime. Using the SRS self-conversion in a Nd3+: KWG laser, lasing was obtained in the eye-safe spectral region at 1.538 nm with the energy up to 5 mJ and a pulse repetition rate up to 20 Hz.

  20. Remote sensing of atmospheric trace gases by diode laser spectroscopy

    NASA Astrophysics Data System (ADS)

    Liu, Jianguo; Kan, Ruifeng; He, Yabai; He, Ying; Zhang, Yujun; Xie, Pinhua; liu, Wenqing

    2016-04-01

    Gaseous ammonia is the most abundant alkaline trace gas in the atmosphere. In order to study its role in acid deposition and aerosol formation, as well as its influence on the regional air quality and atmospheric visibility, several instruments has been developed based on TDLAS (Tunable Diode Laser Absorption Spectroscopy) techniques. In this paper, a long open path TDLAS system and a continuous-wave CRDS (Cavity-Ring down Spectroscopy) system are presented. The long open path system has been developed for NH3 in-situ monitoring by combining wavelength modulation with harmonic detection techniques to obtain the necessary detection sensitivity. The prototype instrument has been used to monitor atmospheric NH3 concentration at an urban site near Beijing National Stadium during Beijing Olympics in 2008, and recently used to measure the fluxes of NH3 from farm fields by flux-gradient method. The detection limit for ammonia is proved approximately 3ppb for a total path length of 456m. The continuous-wave, rapidly swept CRDS system has been developed for localized atmospheric sensing of trace gases at remote sites. Passive open-path optical sensor units could be coupled by optical fiber over distances of >1 km to a single transmitter/receiver console incorporating a photodetector and a swept-frequency diode laser tuned to molecule-specific near-infrared wavelengths. A noise-limited minimum detectable mixing ratio of ~11 ppbv is attained for ammonia at atmospheric pressure. The developed instruments are deployable in agricultural, industrial, and natural atmospheric environments.

  1. Noninvasive blood glucose measurement using multiple laser diodes

    NASA Astrophysics Data System (ADS)

    Ooi, E. T.; Zhang, X. Q.; Chen, J. H.; Soh, P. H.; Ng, K.; Yeo, J. H.

    2007-02-01

    In the event of diabetes clinicians have advocated that frequent monitoring of a diabetic's blood glucose level is the key to avoid future complications (kidney failure, blindness, amputations, premature death, etc.,) associated with the disease. While the test-strip glucose meters available in current consumer markets allow for frequent monitoring, a more convenient technique that is accurate, painless and sample-free is preferable in a diabetic's daily routine. This paper presents a non-invasive blood glucose measurement technique using diffuse reflectance near infrared (NIR) signals. This technique uses a set of laser diodes, each operating at fixed wavelengths in the first overtone region. The NIR signals from the laser diodes are channeled to the measurement site viz., the nail-bed by means of optical fibers. A series of in vivo experiments have been performed on eight normal human subjects using a standard Oral Glucose Tolerance Test (OGTT) protocol. The reflected NIR signals are inputs to a Partial Least Squares (PLS) algorithm for calibration and future predictions. The calibration models used are developed using in vivo datasets and are unique to a particular individual. The 1218 paired points collected from the eight test subjects plotted on the Clarke Error Grid, revealed that 87.3% of these points fall within the A zone while the remainder, within the B zone, both of which, are clinically accepted. The standard error of prediction was +/-13.14mg/dL for the best calibration model. A Bland-Altman analysis of the 1218 paired points yields a 76.3% confidence level for a measurement accuracy of +/-20mg/dL. These results demonstrate the initial potential of the technique for non-invasive blood glucose measurements in vivo.

  2. Passively cooled diode lasers in the cw power range of 120 to 200W

    NASA Astrophysics Data System (ADS)

    Lorenzen, Dirk; Meusel, Jens; Schröder, Dominic; Hennig, Petra

    2008-02-01

    Improvements of laser diode bar efficiency and mounting technology have boosted output powers of passively cooled diode lasers beyond the 100W cw limit. After an introduction about reliablity statements and reliability assessment, the performance increase by technology improvements is documented in current-step failure discrimination tests. Electro-optical parameters of improved diode lasers are subsequently presented in detail as well as the results of lifetime tests at different powers and in different operation modes - steady-state and repetitive/intermittent ("hard pulse") cw operation.

  3. Influence of laser diode red beams on germination rate of tomato seeds

    NASA Astrophysics Data System (ADS)

    Niculita, P.; Danaila-Guidea, Silvana; Livadariu, Oana; Popa, M.; Ristici, M.; Ristici, Esofina

    2007-08-01

    Laser diodes are lighting devices in which the light is generated by stimulated emission rather than spontaneous emission, with high generation efficiency. A device using 20 red laser diodes is presented. Emission wavelengths are in the 650-670 nm range. Emission power for each laser diode is about 4 mW. This device is used to irradiate the tomato seeds with three different irradiating doses. There were three Petri vessels for each dose having 25 seeds each of them. Results show that the germination rate increases for irradiated seeds. The red light has a positive effect for vegetable cultivated in protected area.

  4. Optical bistability in erbium-doped yttrium aluminum garnet crystal combined with a laser diode.

    PubMed

    Maeda, Y

    1994-01-10

    Optical bistability was observed in a simple structure of an injection laser diode combined with an erbium-doped yttrium aluminum garnet crystal. Since a hysteresis characteristic exists in the relationship between the wavelength and the injection current of a laser diode, an optical memory function capable of holding the output status is confirmed. In addition, an optical signal inversion was caused by the decrease of transmission of the erbium-doped yttrium aluminum garnet crystal against the red shift (principally mode hopping) of the laser diode. It is suggested that the switching time of this phenomenon is the time necessary for a mode hopping by current injection. PMID:20862016

  5. Frequency-comb-assisted broadband precision spectroscopy with cascaded diode lasers.

    PubMed

    Liu, Junqiu; Brasch, Victor; Pfeiffer, Martin H P; Kordts, Arne; Kamel, Ayman N; Guo, Hairun; Geiselmann, Michael; Kippenberg, Tobias J

    2016-07-01

    Frequency-comb-assisted diode laser spectroscopy, employing both the accuracy of an optical frequency comb and the broad wavelength tuning range of a tunable diode laser, has been widely used in many applications. In this Letter, we present a novel method using cascaded frequency agile diode lasers, which allows us to extend the measurement bandwidth to 37.4 THz (1355-1630 nm) at megahertz resolution with scanning speeds above 1 THz/s. It is demonstrated as a useful tool to characterize a broadband spectrum for molecular spectroscopy, and in particular it enables us to characterize the dispersion of integrated microresonators up to the 4th-order. PMID:27367120

  6. Computerized diode laser system for CO content investigation in human expiration

    NASA Astrophysics Data System (ADS)

    Kouznetsov, Andrian I.; Logachev, A. P.; Stepanov, Eugene V.

    1990-07-01

    First results of diode laser spectroscopy methods applications for diagnosing the gas content of expired air are presented. Carbon monoxide (CO) contents of expirations of a sportsman and a smoker were subjected to analysis by using a computerized diode laser system. In the first case there was detected a considerable growth of CO concentration after an intensive exercise. In the second one there were revealed and measured three time constants - characteristics of CO removal from the organism. Promising trends of development and applications of diode laser spectroscopy in medicine are at issue.

  7. Quantitative Detection of Combustion Species using Ultra-Violet Diode Lasers

    NASA Technical Reports Server (NTRS)

    Pilgrim, J. S.; Peterson, K. A.

    2001-01-01

    Southwest Sciences is developing a new microgravity combustion diagnostic based on UV diode lasers. The instrument will allow absolute concentration measurements of combustion species on a variety of microgravity combustion platforms including the Space Station. Our approach uses newly available room temperature UV diode lasers, thereby keeping the instrument compact, rugged and energy efficient. The feasibility of the technique was demonstrated by measurement of CH radicals in laboratory flames. Further progress in fabrication technology of UV diode lasers at shorter wavelengths and higher power will result in detection of transient species in the deeper UV. High sensitivity detection of combustion radicals is provided with wavelength modulation absorption spectroscopy.

  8. Advances in high-power 9XXnm laser diodes for pumping fiber lasers

    NASA Astrophysics Data System (ADS)

    Skidmore, Jay; Peters, Matthew; Rossin, Victor; Guo, James; Xiao, Yan; Cheng, Jane; Shieh, Allen; Srinivasan, Raman; Singh, Jaspreet; Wei, Cailin; Duesterberg, Richard; Morehead, James J.; Zucker, Erik

    2016-03-01

    A multi-mode 9XXnm-wavelength laser diode was developed to optimize the divergence angle and reliable ex-facet power. Lasers diodes were assembled into a multi-emitter pump package that is fiber coupled via spatial and polarization multiplexing. The pump package has a 135μm diameter output fiber that leverages the same optical train and mechanical design qualified previously. Up to ~ 270W CW power at 22A is achieved at a case temperature ~ 30ºC. Power conversion efficiency is 60% (peak) that drops to 53% at 22A with little thermal roll over. Greater than 90% of the light is collected at < 0.12NA at 16A drive current that produces 3.0W/(mm-mr)2 radiance from the output fiber.

  9. Effect of thermal processes on critical operation conditions of high-power laser diodes

    SciTech Connect

    Parashchuk, V V; Vu Doan Mien

    2013-10-31

    Using numerical and analytical techniques in a threedimensional approximation, we have modelled the effect of spatial thermoelastic stress nonuniformity in a laser diode – heat sink system on the output characteristics of the device in different operation modes. We have studied the influence of the pulse duration, the geometry of the laser system and its thermophysical parameters on the critical pump current density, in particular for state-of-the-art heat conductive substrate materials. The proposed approach has been used to optimise the laser diode assembly process in terms of the quality of laser crystal positioning (bonding) on a heat sink. (lasers)

  10. Compact and smart laser diode systems for cancer treatment

    NASA Astrophysics Data System (ADS)

    Svirin, Viatcheslav N.; Sokolov, Victor V.; Solovieva, Tatiana I.

    2003-04-01

    To win the cancer is one of the most important mankind task to be decided in III Millenium. New technology of treatment is to recognize and kill cancer cells with the laser light not by surgery operation, but by soft painless therapy. Even though from the beginning of the 80s of the last century this technology, so-called photodynamic therapy (PDT) has received acceptance in America, Europe and Asia it is still considered in the medical circles to be a new method with the little-known approaches of cancer treatment. Recently the next step was done, and the unique method of PDT combined with laser-induced thermotherapy (LITT) was developed. Compact and smart diode laser apparatus "Modul-GF" for its realization was designed. In this report the concept of this method, experimental materials on clinical trials and ways of optimization of technical decisions and software of apparatus "Modul-GF", including the autotuning of laser power dependently on tissue temperature measured with thermosensors are discussed. The special instruments such as fiber cables and special sensors are described to permit application of "Modul-GF" for the treatment of the tumors of the different localizations, both surface and deeply located with using of the endoscopy method. The examples of the oncological and nononcological pathologies" treatment by the developed method and apparatus in urology, gynecology, gastroenterology, dermatology, cosmetology, bronchology, pulmonology are observed. The results of clinical approval the developed combination of PDT&LITT realized with "Modul-GF" leads to essentially increasing of the treatment effectiveness.

  11. Supersonic diode pumped alkali lasers: Computational fluid dynamics modeling

    NASA Astrophysics Data System (ADS)

    Rosenwaks, Salman; Yacoby, Eyal; Waichman, Karol; Sadot, Oren; Barmashenko, Boris D.

    2015-10-01

    We report on recent progress on our three-dimensional computational fluid dynamics (3D CFD) modeling of supersonic diode pumped alkali lasers (DPALs), taking into account fluid dynamics and kinetic processes in the lasing medium. For a supersonic Cs DPAL with laser section geometry and resonator parameters similar to those of the 1-kW flowing-gas subsonic Cs DPAL [A.V. Bogachev et al., Quantum Electron. 42, 95 (2012)] the maximum achievable output power, ~ 7 kW, is 25% higher than that achievable in the subsonic case. Comparison between semi-analytical and 3D CFD models for Cs shows that the latter predicts much higher maximum achievable output power than the former. Optimization of the laser parameters using 3D CFD modeling shows that very high power and optical-to-optical efficiency, 35 kW and 82%, respectively, can be achieved in a Cs supersonic device pumped by a collimated cylindrical (0.5 cm diameter) beam. Application of end- or transverse-pumping by collimated rectangular (large cross section ~ 2 - 4 cm2) beam makes it possible to obtain even higher output power, > 250 kW, for ~ 350 kW pumping power. The main processes limiting the power of Cs supersonic DPAL are saturation of the D2 transition and large ~ 40% losses of alkali atoms due to ionization, whereas the influence of gas heating is negligibly small. For supersonic K DPAL both gas heating and ionization effects are shown to be unimportant and the maximum achievable power, ~ 40 kW and 350 kW, for pumping by ~ 100 kW cylindrical and ~ 700 kW rectangular beam, respectively, are higher than those achievable in the Cs supersonic laser. The power achieved in the supersonic K DPAL is two times higher than for the subsonic version with the same resonator and K density at the gas inlet, the maximum optical-to-optical efficiency being 82%.

  12. Tunable frequency stabilized diode-laser-pumped Tm,Ho:YLiF4 laser at room temperature

    NASA Technical Reports Server (NTRS)

    Mcguckin, Brendan T.; Menzies, Robert T.; Esproles, Carlos

    1993-01-01

    A diode-laser-pumped single-frequency thulium holmium yttrium lithium fluoride laser that exhibits a closed-loop stability of a few megahertz and a continuous single-mode tuning range of 800 MHz is described. The laser output power is 25 mW, and is tunable over about 8/cm at 25 C.

  13. Low-Cost, Single-Frequency Sources for Spectroscopy Using Conventional Fabry-Perot Diode Lasers

    NASA Technical Reports Server (NTRS)

    Krainak, Michael A.; Duerksen, Gary L.

    1999-01-01

    Commercial (uncoated) Fabry-Perot laser diodes are converted to single-frequency spectroscopy sources by passively locking the laser frequency to the band edge of a fiber Bragg grating, which phase-locks the laser oscillations through self-injection seeding.

  14. Low-Cost, Single-Frequency Sources for Spectroscopy using Conventional Fabry-Perot Diode Lasers

    NASA Technical Reports Server (NTRS)

    Duerksen, Gary L.; Krainak, Michael A.

    1999-01-01

    Commercial (uncoated) Fabry-Perot laser diodes are converted to single-frequency spectroscopy sources by passively locking the laser frequency to the band edge of a fiber Bragg grating, which phase-locks the laser oscillations through self-injection seeding.

  15. Efficient emission at 1908 nm in a diode-pumped Tm:YLF laser

    SciTech Connect

    Zakharov, N G; Antipov, Oleg L; Savikin, A P; Sharkov, V V; Eremeikin, O N; Frolov, Yu N; Mishchenko, G M; Velikanov, S D

    2009-05-31

    Emission parameters at 1908 nm in a longitudinally-diode-pumped Tm:YLF laser are studied. The laser parameters are optimised to obtain the maximal power of high-quality cw radiation. The output power of {approx}27 W is obtained at the slope efficiency of {approx}50% and total optical pump conversion efficiency of {approx}41%. (lasers and amplifiers)

  16. New class of compact diode pumped sub 10-fs lasers for biomedical applications

    NASA Astrophysics Data System (ADS)

    Le, T.; Müller, A.; Sumpf, B.; Jensen, O. B.; Hansen, A. K.; Andersen, P. E.

    2016-03-01

    Diode-pumping Ti:sapphire lasers promises a new approach to low-cost femtosecond light sources. Thus in recent years much effort has been taken just to overcome the quite low power and low beam qualities of available green diodes to obtain output powers of several hundred milliwatts from a fs-laser. In this work we present an alternative method by deploying frequency-doubled IR diodes with good beam qualities to pump fs-lasers. The revolutionary approach allows choosing any pump wavelengths in the green region and avoids complicated relay optics for the diodes. For the first time we show results of a diode-pumped 10 fs-laser and how a single diode setup can be integrated into a 30 x 30 cm2 fs-laser system generating sub 20 fs laser pulses with output power towards half a Watt. This technology paves the way for a new class of very compact and cost-efficient fs-lasers for life science and industrial applications.

  17. High-power pulsed laser diodes emitting in the range 1.5 – 1.6 μm

    SciTech Connect

    Gorlachuk, P V; Ryaboshtan, Yu L; Ladugin, M A; Padalitsa, A A; Marmalyuk, A A; Kurnosov, V D; Kurnosov, K V; Zhuravleva, O V; Romantsevich, V I; Chernov, R V; Ivanov, A V; Simakov, V A

    2013-09-30

    This paper examines approaches for increasing the output pulse power of laser diodes based on MOVPE InGaAs/AlGaInAs/InP heterostructures and emitting in the range 1.5 – 1.6 μm. We demonstrate that optimising waveguide layer parameters may ensure an increase in the quantum efficiency of the laser diodes and a reduction in their internal optical loss. Characterisation results are presented for laser diodes based on the proposed heterostructures. (lasers)

  18. Monitoring of catalyst performance in CO2 lasers using frequency modulation spectroscopy with diode lasers

    NASA Technical Reports Server (NTRS)

    Wang, Liang-Guo; Sachse, Glen

    1990-01-01

    Closed-cycle CO2 laser operation with removal of O2 and regeneration of CO2 can be achieved by catalytic CO-O2 recombination. Both parametric studies of the optimum catalyst formulation and long-term performance tests require on line monitoring of CO, O2 and CO2 concentrations. There are several existing methods for molecular oxygen detection. These methods are either intrusive (such as electrochemical method or mass spectrometry) or very expensive (such as CARS, UV laser absorption). Researchers demonstrated a high-sensitivity spectroscopic measurement of O2 using the two-tone frequency modulation spectroscopy (FMS) technique with a near infrared GaAlAs diode laser. Besides its inexpensive cost, fast response time, nonintrusive measurements and high sensitivity, this technique may also be used to differentiate between isotopes due to its high spectroscopic resolution. This frequency modulation spectroscopy technique could also be applied for the on-line monitoring of CO and CO2 using InGaAsP diode lasers operation in the 1.55 microns region and H2O in the 1.3 microns region. The existence of single mode optical fibers at the near infrared region makes it possible to combine FMS with optical fiber technology. Optical fiber FMS is particularly suitable for making point-measurements at one or more locations in the CO2 laser/catalyst system.

  19. Chlorine analysis by diode laser atomic absorption spectrometry.

    PubMed

    Koch, J; Zybin, A; Niemax, K

    2000-04-01

    The general characteristics of Diode Laser Absorption Spectrometry (DLAAS) in low pressure plasmas particularly with respect to the detection of non-metals are comprehensively recapitulated and discussed. Furthermore, a detector, which is based on DLAAS in a microwave-induced low pressure plasma as an alternative technique for halogene-specific analysis of volatile compounds and polymeric matrices is described. The analytical capability of the technique is demonstrated on the chlorine-specific analysis of ablated polymer fragments as well as gas chromatographically separated hydrocarbons. Since the measurements were carried out by means of a balanced-heterodyne detection scheme, different technical noise contributions, such as laser excess and RAM noise could efficiently be suppressed and the registered absorption was limited only by the principal shot noise. Thus, in the case of the polymer analysis a chlorine-specific absolute detection limit of 10 pg could be achieved. Furthermore, fundamental investigations concerning the influence of hydrocarbons on the dissociation capability of the microwave induced plasma were performed. For this purpose, the carbon-, chlorine- and hydrogen-specific stoichiometry of the compounds were empirically determined. Deviations from the expected proportions were found to be insignificant, implying the possibility of internal standardization relative to the response of a reference sample. PMID:12953476

  20. High-brightness 9xxnm fiber coupled diode lasers

    NASA Astrophysics Data System (ADS)

    Liu, Rui; Jiang, Xiaochen; Yang, Thomas; He, Xiaoguang; Gao, Yanyan; Zhu, Jing; Zhang, Tujia; Guo, Weirong; Wang, Baohua; Guo, Zhijie; Zhang, Luyan; Chen, Louisa

    2015-03-01

    We developed a high brightness fiber coupled diode laser module providing more than 140W output power from a 105μm NA 0.15 fiber at the wavelength of 915nm.The high brightness module has an electrical to optical efficiency better than 45% and power enclosure more than 90% within NA 0.13. It is based on multi-single emitters using optical and polarization beam combining and fiber coupling technique. With the similar technology, over 100W of optical power into a 105μm NA 0.15 fiber at 976nm is also achieved which can be compatible with the volume Bragg gratings to receive narrow and stabilized spectral linewidth. The light within NA 0.12 is approximately 92%. The reliability test data of single and multiple single emitter laser module under high optical load are also presented and analyzed using a reliability model with an emitting aperture optimized for coupling into 105μm core fiber. The total MTTF shows exceeding 100,000 hours within 60% confidence level. The packaging processes and optical design are ready for commercial volume production.

  1. Histopathology of diode and argon laser lesions in rabbit retina. A comparative study

    SciTech Connect

    Brancato, R.; Pratesi, R.; Leoni, G.; Trabucchi, G.; Vanni, U.

    1989-07-01

    Argon lasers are the most frequently used laser source for retinal photocoagulation. These are expensive, bulky and low-efficiency devices. In contrast, diode semiconductor lasers have a number of characteristics that make them attractive for medical application: compact size, high electrical-to-optical efficiency, and long operating lifetime. Comparable irradiance lesions (about 120 Wcm2), ophthalmoscopically similar to those obtained therapeutically in humans, were obtained by a diode and an argon laser. Twenty-four hours after the treatment, a study of these lesions was made by light and electron microscopy. Argon irradiations resulted in damage to both the inner and the outer retinal layers, while the diode laser radiation produced damage to the outer retina and choroid. A sufficient diode laser light passed into the choroid to induce small vessel occlusions and/or edema. The histological characteristics of the lesions produced by the two lasers suggest the use of the diode lasers, as well as argon lasers, in the treatment of retinal and subretinal pathologies.

  2. AlGaInN laser diode technology and systems for defence and security applications

    NASA Astrophysics Data System (ADS)

    Najda, Stephen P.; Perlin, Piotr; Suski, Tadek; Marona, Lujca; Boćkowski, Mike; Leszczyński, Mike; Wisniewski, Przemek; Czernecki, Robert; Kucharski, Robert; Targowski, Grzegorz; Watson, Scott; Kelly, Antony E.

    2015-10-01

    AlGaInN laser diodes is an emerging technology for defence and security applications such as underwater communications and sensing, atomic clocks and quantum information. The AlGaInN material system allows for laser diodes to be fabricated over a very wide range of wavelengths from u.v., ~380nm, to the visible ~530nm, by tuning the indium content of the laser GaInN quantum well. Thus AlGaInN laser diode technology is a key enabler for the development of new disruptive system level applications in displays, telecom, defence and other industries. Ridge waveguide laser diodes are fabricated to achieve single mode operation with optical powers up to 100mW with the 400-440nm wavelength range with high reliability. Visible free-space and underwater communication at frequencies up to 2.5GHz is reported using a directly modulated 422nm GaN laser diode. Low defectivity and highly uniform GaN substrates allow arrays and bars to be fabricated. High power operation operation of AlGaInN laser bars with up to 20 emitters have been demonstrated at optical powers up to 4W in a CS package with common contact configuration. An alternative package configuration for AlGaInN laser arrays allows for each individual laser to be individually addressable allowing complex free-space or optical fibre system integration with a very small form-factor.

  3. Cr-doped solid state lasers pumped by visible laser diodes

    NASA Astrophysics Data System (ADS)

    Scheps, Richard

    1992-01-01

    Operation of Cr 3+-doped solid state lasers pumped by visible laser diodes is discussed, with performance of three of the highest efficiency devices reported in detail. Cr:LiCaAlF 6 (Cr:LiCAF), Cr:LiSrAlF 6 (Cr:LiSAF) and Cr,Nd: Gd 3Sc 2Ga 3O 12 (Cr,Nd: GSGG) have all demonstrated low threshold and high slope efficiency when pumped with diodide power as high as 1 W. Laser emission levels have approached 200 mW while slope efficiencies as high as 50% were measured. Optical characterization 3ata for each laser resonator are presented and prospects for near-term power scaling are discussed.

  4. Laser-diode pumped glass-clad Ti:sapphire crystal fiber laser.

    PubMed

    Wang, Shih-Chang; Hsu, Chun-Yang; Yang, Tzu-Te; Jheng, Dong-Yo; Yang, Teng-I; Ho, Tuan-Shu; Huang, Sheng-Lung

    2016-07-15

    Efficient glass-clad crystal fiber (CF) lasers were demonstrated using a Ti:sapphire crystalline core as the gain medium. With a core diameter of 18 μm, the laser diode (LD) pump source can be effectively coupled and guided throughout the crystal fiber for a low threshold and high slope efficiency laser operation. The advantage of high heat dissipation efficiency of the fiber structure can be derived from the low core temperature rising measurement (i.e., 17 K/W) with passive cooling. At an output transmittance of 23%, the lowest absorbed threshold of 118.2 mW and highest slope efficiency of 29.6% were achieved, with linear laser polarization. PMID:27420499

  5. 954 nm Raman fiber laser with multimode laser diode pumping

    NASA Astrophysics Data System (ADS)

    Zlobina, E. A.; Kablukov, S. I.; Skvortsov, M. I.; Nemov, I. N.; Babin, S. A.

    2016-03-01

    CW Raman fiber laser emitting at 954 nm under direct pumping by a high-power multimode laser diode at 915 nm is demonstrated. A cavity of the laser is formed with 2.5 km-long multimode graded-index fiber and two mirrors: highly reflective fiber Bragg grating (FBG) at one side and normally cleaved fiber end at the other side. The laser generates low-index transverse modes at the Stokes wavelength with output power above 4 W at a slope efficiency above 40%. It is shown that utilization of a narrowband FBG mirror with low reflectivity instead of the cleaved fiber end with Fresnel reflection leads to stronger spectral mode selection, but the generated power is reduced in this case.

  6. High power diode laser array development using completely indium free packaging technology with narrow spectrum

    NASA Astrophysics Data System (ADS)

    Hou, Dong; Wang, Jingwei; Gao, Lijun; Liang, Xuejie; Li, Xiaoning; Liu, Xingsheng

    2016-03-01

    The high power diode lasers have been widely used in many fields. In this work, a sophisticated high power and high performance horizontal array of diode laser stacks have been developed and fabricated with high duty cycle using hard solder bonding technology. CTE-matched submount and Gold Tin (AuSn) hard solder are used for bonding the diode laser bar to achieve the performances of anti-thermal fatigue, higher reliability and longer lifetime. This array consists of 30 bars with the expected optical output peak power of 6000W. By means of numerical simulation and analytical results, the diode laser bars are aligned on suitable positions along the water cooled cooler in order to achieve the uniform wavelength with narrow spectrum and accurate central wavelength. The performance of the horizontal array, such as output power, spectrum, thermal resistance, life time, etc., is characterized and analyzed.

  7. 100  J-level nanosecond pulsed diode pumped solid state laser.

    PubMed

    Banerjee, Saumyabrata; Mason, Paul D; Ertel, Klaus; Jonathan Phillips, P; De Vido, Mariastefania; Chekhlov, Oleg; Divoky, Martin; Pilar, Jan; Smith, Jodie; Butcher, Thomas; Lintern, Andrew; Tomlinson, Steph; Shaikh, Waseem; Hooker, Chris; Lucianetti, Antonio; Hernandez-Gomez, Cristina; Mocek, Tomas; Edwards, Chris; Collier, John L

    2016-05-01

    We report on the successful demonstration of a 100 J-level, diode pumped solid state laser based on cryogenic gas cooled, multi-slab ceramic Yb:YAG amplifier technology. When operated at 175 K, the system delivered a pulse energy of 107 J at a 1 Hz repetition rate and 10 ns pulse duration, pumped by 506 J of diode energy at 940 nm, corresponding to an optical-to-optical efficiency of 21%. To the best of our knowledge, this represents the highest energy obtained from a nanosecond pulsed diode pumped solid state laser. This demonstration confirms the energy scalability of the diode pumped optical laser for experiments laser architecture. PMID:27128081

  8. MEASUREMENT OF AMMONIA EMISSIONS FROM MECHANICALLY VENTILATED POULTRY HOUSES USING MULTIPATH TUNABLE DIODE LASER SPECTROSCOPY

    EPA Science Inventory

    Ammonia emissions from mechanically ventilated poultry operations are an important environmental concern. Open Path Tunable Diode Laser Absorption Spectroscopy has emerged as a robust real-time method for gas phase measurement of ammonia concentrations in agricultural settings. ...

  9. Output characteristics of a semiconductor laser diode with two circular ring resonators

    NASA Astrophysics Data System (ADS)

    Shih, Ming Chang; Kao, Yi Hsiang; How Lan, Wen

    2016-04-01

    Here, we present the output characteristics of a semiconductor laser diode with two circular ring resonators. The material of the laser diode is a metal organic chemical vapor deposition (MOCVD)-grown InGaAlP multiple-quantum-well (MQW) structure. The current injection of the laser diode is confined by the ridge waveguide of two circular ring resonators connected by two directional couplers. The confined light output through the nonwaveguide region of the substrate was observed. Measurements of light-current (L-I) and spectral characteristics at each output terminal were presented. These measurements showed asymmetric output characteristics of emission from two directional coupling terminals. In addition, output characteristics of a laser diode device with larger diameter ring resonators showed shifting of the lasing emission wavelength from a different side of the output coupling terminal.

  10. High-power narrow-vertical-divergence photonic band crystal laser diodes with optimized epitaxial structure

    SciTech Connect

    Liu, Lei; Qu, Hongwei; Liu, Yun; Zhang, Yejin; Zheng, Wanhua; Wang, Yufei; Qi, Aiyi

    2014-12-08

    900 nm longitudinal photonic band crystal (PBC) laser diodes with optimized epitaxial structure are fabricated. With a same calculated fundamental-mode divergence, stronger mode discrimination is achieved by a quasi-periodic index modulation in the PBC waveguide than a periodic one. Experiments show that the introduction of over 5.5 μm-thick PBC waveguide contributes to only 10% increment of the internal loss for the laser diodes. For broad area PBC lasers, output powers of 5.75 W under continuous wave test and over 10 W under quasi-continuous wave test are reported. The vertical divergence angles are 10.5° at full width at half maximum and 21.3° with 95% power content, in conformity with the simulated angles. Such device shows a prospect for high-power narrow-vertical-divergence laser emission from single diode laser and laser bar.

  11. Ultra high brightness laser diode arrays for pumping of compact solid state lasers and direct applications

    NASA Astrophysics Data System (ADS)

    Kohl, Andreas; Fillardet, Thierry; Laugustin, Arnaud; Rabot, Olivier

    2012-10-01

    High Power Laser Diodes (HPLD) are increasingly used in different fields of applications such as Industry, Medicine and Defense. Our significant improvements of performances (especially in power and efficiency) and a reproducible manufacturing process have led to reliable, highly robust components. For defense and security applications these devices are used predominantly for pumping of solid state lasers (ranging, designation, countermeasures, and sensors). Due to the drastically falling price per watt they are more and more replacing flash lamps as pump sources. By collimating the laser beam even with a bar to bar pitch of only 400μm. cutting edge brightness of our stacks.is achieved Due the extremely high brightness and high power density these stacks are an enabling technology for the development of compact highly efficient portable solid state lasers for applications as telemeters and designators on small platforms such as small UAVs and handheld devices. In combination with beam homogenizing optics their compact size and high efficiency makes these devices perfectly suited as illuminators for portable active imaging systems. For gated active imaging systems a very short pulse at high PRF operation is required. For this application we have developed a diode driver board with an efficiency several times higher than that of a standard driver. As a consequence this laser source has very low power consumption and low waste heat dissipation. In combination with its compact size and the integrated beam homogenizing optics it is therefore ideally suited for use in portable gated active imaging systems. The kWatt peak power enables a range of several hundred meters. The devices described in this paper mostly operate at wavelength between 800 nm and 980nm. Results from diodes operating between 1300 nm and 1550 nm are presented as well.

  12. Enhanced Type-I Polarization-Entangled Photons Using CW-Diode Laser

    NASA Astrophysics Data System (ADS)

    Hegazi, Salem; Mansour, Mohy S.; El Nadi, Lotfia

    2013-03-01

    We used two type-I BBO crystals pumped by violet cw-diode laser of relatively wide bandwidth to produce entangled photons of considerable degree of purity. While diode laser serves the mobility and the low-cost of the entangled photons source, suitable temporal compensation is required in this case to recover the purity of the state. We studied also effect of tilting the two-crystal set on overlapping of the SPDC cones.

  13. High-efficiency diode-pumped femtosecond Yb:YAG ceramic laser.

    PubMed

    Zhou, Binbin; Wei, Zhiyi; Zou, Yuwan; Zhang, Yongdong; Zhong, Xin; Bourdet, G L; Wang, Junli

    2010-02-01

    A highly efficient diode-end-pumped femtosecond Yb:yttrium aluminum garnet (YAG) ceramic laser was demonstrated. Pumped by a 968 nm fiber-coupled diode laser, 1.9 W mode-locked output power at a repetition rate of 64.27 MHz was obtained with 3.5 W absorbed pump power, corresponding to a slope efficiency of 76%. Our measurement showed that the pulse duration was 418 fs with the central wavelength of 1048 nm. PMID:20125697

  14. Proceedings of the 5th International Symposium on Blue Laser and Light Emitting Diodes (ISBLLED-2004)

    NASA Astrophysics Data System (ADS)

    Suh, Eun-Kyung; Yoon, Euijoon; Lee, Hyung Jae

    2004-09-01

    The 5th International Symposium on Blue Laser and Light Emitting Diodes (ISBLLED-2004) was held in Gyeongju, Korea, 15-19 March 2004. The purpose of the symposium was to provide a forum for scientists and engineers to discuss recent progress and future trends in the rapidly advancing wide band gap semiconductor science and technologies and their applications in blue laser and light emitting diodes.

  15. High-sensitivity sensor of gases based on IR tunable diode lasers for human exhalation monitoring

    NASA Astrophysics Data System (ADS)

    Moskalenko, Konstantin L.; Nadezhdinskii, Alexander I.; Stepanov, Eugene V.

    1991-06-01

    Results on tunable diode laser spectroscopy applications in analysis of human expiration are presented. Carbon monoxide concentrations in exhaled air of several non-smoking adults were measured with high sensitivity. Obtained CO contents slightly exceed atmosphere level and correlate with it. Simultaneous measurements of carbon monoxide and carbon dioxide were carried out using single diode laser generated at 4.7 microns. Dependences of their concentration in exhaled air on breath-holding time were investigated.

  16. Two-wavelength laser-diode heterodyne interferometry with one phasemeter

    NASA Astrophysics Data System (ADS)

    Onodera, Ribun; Ishii, Yukihiro

    1995-12-01

    A two-wavelength laser-diode interferometer that is based on heterodyne detection with one phasemeter has been constructed. Two laser diodes are frequency modulated by mutually inverted sawtooth currents on an unbalanced interferometer. One can measure the tested phase at a synthetic wavelength from the sum of the interference beat signals by synchronizing them with the modulation frequency. The experimental result presented shows a phase-measurement range with a 4.7- mu m synthetic wavelength.

  17. Diode end pumped laser and harmonic generator using same

    NASA Technical Reports Server (NTRS)

    Byer, Robert L. (Inventor); Dixon, George J. (Inventor); Kane, Thomas J. (Inventor)

    1988-01-01

    A second harmonic, optical generator is disclosed in which a laser diode produces an output pumping beam which is focused by means of a graded, refractive index rod lens into a rod of lasant material, such as Nd:YAG, disposed within an optical resonator to pump the lasant material and to excite the optical resonator at a fundamental wavelength. A non-linear electro-optic material such as MgO:LiNbO.sub.3 is coupled to the excited, fundamental mode of the optical resonator to produce a non-linear interaction with the fundamental wavelength producing a harmonic. In one embodiment, the gain medium and the non-linear material are disposed within an optical resonator defined by a pair of reflectors, one of which is formed on a face of the gain medium and the second of which is formed on a face of the non-linear medium. In another embodiment, the non-linear, electro-optic material is doped with the lasant ion such that the gain medium and the non-linear doubling material are co-extensive in volume. In another embodiment, a non-linear, doubling material is disposed in an optical resonator external of the laser gai medium for improved stability of the second harmonic generation process. In another embodiment, the laser gain medium andthe non-linear material are bonded together by means of an optically transparent cement to form a mechanically stable, monolithic structure. In another embodiment, the non-linear material has reflective faces formed thereon to define a ring resonator to decouple reflections from the non-linear medium back to the gain medium for improved stability.

  18. High-brightness 800nm fiber-coupled laser diodes

    NASA Astrophysics Data System (ADS)

    Berk, Yuri; Levy, Moshe; Rappaport, Noam; Tessler, Renana; Peleg, Ophir; Shamay, Moshe; Yanson, Dan; Klumel, Genadi; Dahan, Nir; Baskin, Ilya; Shkedi, Lior

    2014-03-01

    Fiber-coupled laser diodes have become essential sources for fiber laser pumping and direct energy applications. Single emitters offer reliable multi-watt output power from a 100 m lateral emission aperture. By their combination and fiber coupling, pump powers up to 100 W can be achieved from a low-NA fiber pigtail. Whilst in the 9xx nm spectral range the single emitter technology is very mature with <10W output per chip, at 800nm the reliable output power from a single emitter is limited to 4 W - 5 W. Consequently, commercially available fiber coupled modules only deliver 5W - 15W at around 800nm, almost an order of magnitude down from the 9xx range pumps. To bridge this gap, we report our advancement in the brightness and reliability of 800nm single emitters. By optimizing the wafer structure, laser cavity and facet passivation process we have demonstrated QCW device operation up to 19W limited by catastrophic optical damage to the 100 μm aperture. In CW operation, the devices reach 14 W output followed by a reversible thermal rollover and a complete device shutdown at high currents, with the performance fully rebounded after cooling. We also report the beam properties of our 800nm single emitters and provide a comparative analysis with the 9xx nm single emitter family. Pump modules integrating several of these emitters with a 105 μm / 0.15 NA delivery fiber reach 35W in CW at 808 nm. We discuss the key opto-mechanical parameters that will enable further brightness scaling of multi-emitter pump modules.

  19. AlGaInN laser diode technology for defence, security and sensing applications

    NASA Astrophysics Data System (ADS)

    Najda, Stephen P.; Perlin, Piotr; Suski, Tadek; Marona, Lucja; Boćkowski, Mike; Leszczyński, Mike; Wisniewski, Przemek; Czernecki, Robert; Kucharski, Robert; Targowski, Grzegorz; Watson, Scott; Kelly, Antony E.

    2014-10-01

    The latest developments in AlGaInN laser diode technology are reviewed for defence, security and sensing applications. The AlGaInN material system allows for laser diodes to be fabricated over a very wide range of wavelengths from u.v., i.e, 380nm, to the visible, i.e., 530nm, by tuning the indium content of the laser GaInN quantum well. Advantages of using Plasma assisted MBE (PAMBE) compared to more conventional MOCVD epitaxy to grow AlGaInN laser structures are highlighted. Ridge waveguide laser diode structures are fabricated to achieve single mode operation with optical powers of <100mW in the 400-420nm wavelength range that are suitable for telecom applications. Visible light communications at high frequency (up to 2.5 Gbit/s) using a directly modulated 422nm Gallium-nitride (GaN) blue laser diode is reported. High power operation of AlGaInN laser diodes is demonstrated with a single chip, AlGaInN laser diode `mini-array' with a common p-contact configuration at powers up to 2.5W cw at 410nm. Low defectivity and highly uniform GaN substrates allow arrays and bars of nitride lasers to be fabricated. GaN laser bars of up to 5mm with 20 emitters, mounted in a CS mount package, give optical powers up to 4W cw at ~410nm with a common contact configuration. An alternative package configuration for AlGaInN laser arrays allows for each individual laser to be individually addressable allowing complex free-space and/or fibre optic system integration within a very small form-factor.or.

  20. High-Efficiency 894-nm Laser Emission of Laser-Diode-Bar-Pumped Cesium-Vapor Laser

    NASA Astrophysics Data System (ADS)

    Zheng, Yujin; Niigaki, Minoru; Miyajima, Hirofumi; Hiruma, Teruo; Kan, Hirofumi

    2009-03-01

    We report a high-efficiency cesium-vapor laser with a high-gas-pressure (˜3-atm helium and 0.49-atm ethane) cell pumped by a high-power external-cavity laser-diode bar. Peak laser power of 12.1 W at 894 nm was obtained, when the absorbed peak pump power was 23.1 W. The achieved slope efficiencies with the incident pump power and the absorbed pump power were 33 and 81.7%, respectively.

  1. Promoting Robust Design of Diode Lasers for Space: A National Initiative

    NASA Technical Reports Server (NTRS)

    Tratt, David M.; Amzajerdian, Farzin; Kashem, Nasir B.; Shapiro, Andrew A.; Mense, Allan T.

    2007-01-01

    The Diode-laser Array Working Group (DAWG) is a national-level consumer/provider forum for discussion of engineering and manufacturing issues which influence the reliability and survivability of high-power broad-area laser diode devices in space, with an emphasis on laser diode arrays (LDAs) for optical pumping of solid-state laser media. The goals of the group are to formulate and validate standardized test and qualification protocols, operational control recommendations, and consensus manufacturing and certification standards. The group is using reliability and lifetime data collected by laser diode manufacturers and the user community to develop a set of standardized guidelines for specifying and qualifying laser diodes for long-duration operation in space, the ultimate goal being to promote an informed U.S. Government investment and procurement strategy for assuring the availability and durability of space-qualified LDAs. The group is also working to establish effective implementation of statistical design techniques at the supplier design, development, and manufacturing levels to help reduce product performance variability and improve product reliability for diodes employed in space applications

  2. Design of diode-pumped solid-state laser applied in laser fuses

    NASA Astrophysics Data System (ADS)

    Deng, FangLin; Zhang, YiFei

    2005-04-01

    The function of laser fuzes which are parts of certain weapon systems is to control the blasting height of warheads. Commonly the battle environment these weapon systems are confronted with is very complicated and the tactical demand for them is very rigor, so laser fuzes equipped for them must fulfill some special technical requirements, such as high repetition rate, long ranging scope, etc. Lasers are one of key components which constitute fuze systems. Whether designed lasers are advanced and reasonable will determine whether laser fuzes can be applied in these weapon systems or not. So we adopt the novel technology of diode-pumped solid-state laser (DPSSL) to design lasers applied in fuzes. Nd:YVO4 crystal is accepted as gain material, which has wide absorption band and large absorption efficient for 808nm pumping laser. As warhead's temperature is usually very high, wider absorption band is beneficial to reduce the influence of temperature fluctuation. Passive Q-switching with Cr4+:YAG is used to reduce the power consumption farthest. Design the end-pumped microchip sandwich-architecture to decrease lasers' size and increase the reliability, further it's advantageous to produce short pulses and increase peak power of lasers. The designed DPSSL features small size and weight, high repetition rate and peak power, robustness, etc. The repetition rate is expected to reach 1 kHz; peak power will exceed 300 kW; pulse width is only 5 ns; and divergence angle of laser beams is less than 5 mrad. So DPSSL is suitable for laser fuzes as an emitter.

  3. High power diode lasers emitting from 639 nm to 690 nm

    NASA Astrophysics Data System (ADS)

    Bao, L.; Grimshaw, M.; DeVito, M.; Kanskar, M.; Dong, W.; Guan, X.; Zhang, S.; Patterson, J.; Dickerson, P.; Kennedy, K.; Li, S.; Haden, J.; Martinsen, R.

    2014-03-01

    There is increasing market demand for high power reliable red lasers for display and cinema applications. Due to the fundamental material system limit at this wavelength range, red diode lasers have lower efficiency and are more temperature sensitive, compared to 790-980 nm diode lasers. In terms of reliability, red lasers are also more sensitive to catastrophic optical mirror damage (COMD) due to the higher photon energy. Thus developing higher power-reliable red lasers is very challenging. This paper will present nLIGHT's released red products from 639 nm to 690nm, with established high performance and long-term reliability. These single emitter diode lasers can work as stand-alone singleemitter units or efficiently integrate into our compact, passively-cooled Pearl™ fiber-coupled module architectures for higher output power and improved reliability. In order to further improve power and reliability, new chip optimizations have been focused on improving epitaxial design/growth, chip configuration/processing and optical facet passivation. Initial optimization has demonstrated promising results for 639 nm diode lasers to be reliably rated at 1.5 W and 690nm diode lasers to be reliably rated at 4.0 W. Accelerated life-test has started and further design optimization are underway.

  4. Efficacy of Diode Laser for the Management of Potentially Malignant Disorders

    PubMed Central

    Reddy Kundoor, Vinay Kumar; Patimeedi, Ashwini; Roohi, Shameena; Maloth, Kotya Naik; Kesidi, Sunitha; Masabattula, Geetha Kumari

    2015-01-01

    Introduction: Laser dentistry is a one of the upcoming advanced treatment modality for oral mucosal lesions. Diode laser is a soft tissue laser that has found much acceptance in all branches of dentistry. Available compact size and feasibility has render diode laser an enhanced tool for today’s clinical practice. The aim of this study is to determine the efficacy and safety of diode laser for the management of white lesions such as oral leukoplakia (OL) and oral lichen planus (OLP). Methods: The study was conducted by using diode laser 980 nm on 10 patients with white lesions (5 OL and 5 OLP) aged between 35 to 65 years. Results: Of the 10 patients (5 OL and 5 OLP), 3 patients (30%) complained of moderate pain and 7 patients (70%) complained of mild pain, for first 3 days after laser irradiation, and pain disappeared at end of first week. There was no recurrence of the lesion during the 6-month follow up. Conclusion: Diode lasers provide acceptable clinical improvement of potentially malignant lesions with minimal side effects. It can be considered one of the best alternative treatment modality for oral mucosal lesions. PMID:26464779

  5. Laser assisted die bending: a new application of high power diode lasers

    NASA Astrophysics Data System (ADS)

    Schuöcker, D.; Schumi, T.; Spitzer, O.; Bammer, F.; Schuöcker, G.; Sperrer, G.

    2015-02-01

    Nowadays high power lasers are mainly used for cutting of sheet metals, for welding, hardening and rapid prototyping. In the forming of sheet metals as bending or deep drawing lasers are not used. Nevertheless a few years ago a new application of high power lasers has been invented, where bending of materials that break at room temperature becomes possible by heating them along the bending edge with high power lasers thus allowing their treatment without cracks and rupture. For this purpose a large number of diode lasers are arranged in the bottom tool of a bending machine (a V-shaped die) which heat up the initially flat sheet metal during the bending process what is performed by pressing it into the die with a knife shaped upper tool where due to the laser heating the material is softened and thus cracks are avoided. For the technical realization of the new process of laser assisted die bending, modules equipped with numerous laser diodes and a total beam power of 2,5 kW are used. The light emitted by these modules enters a tool with a length of 15cm and is deflected towards the workpiece. By using ten of these modules with adjacent dies and by integrating those in a bending press a bending edge of sheet metals with a length of 1500mm can be realized. Such a bending press with laser assistance also needs energization with a power of practically 50kW, a respective water flow, a heat exchanger system and also a control for all functions of this system. Special measures have also been developed to avoid radiating of those tools that are not covered by a workpiece in the case of bending edges shorter than the full length of the bending tools whereas individual short circuiting of diode modules can be performed. Specific measures to ensure a safe operation without any harm to the operational person have been realized. Exploitation of the bending process has been carried out for titanium, where material thicknesses up to 3mm have been bent successfully.

  6. High-power AlGaAs channeled substrate planar diode lasers for spaceborne communications

    NASA Technical Reports Server (NTRS)

    Connolly, J. C.; Goldstein, B.; Pultz, G. N.; Slavin, S. E.; Carlin, D. B.; Ettenberg, M.

    1988-01-01

    A high power channeled substrate planar AlGaAs diode laser with an emission wavelength of 8600 to 8800 A was developed. The optoelectronic behavior (power current, single spatial and spectral behavior, far field characteristics, modulation, and astigmatism properties) and results of computer modeling studies on the performance of the laser are discussed. Lifetest data on these devices at high output power levels is also included. In addition, a new type of channeled substrate planar laser utilizing a Bragg grating to stabilize the longitudinal mode was demonstrated. The fabrication procedures and optoelectronic properties of this new diode laser are described.

  7. External cavity diode laser based upon an FBG in an integrated optical fiber platform.

    PubMed

    Lynch, Stephen G; Holmes, Christopher; Berry, Sam A; Gates, James C; Jantzen, Alexander; Ferreiro, Teresa I; Smith, Peter G R

    2016-04-18

    An external cavity diode laser is demonstrated using a Bragg grating written into a novel integrated optical fiber platform as the external cavity. The cavity is fabricated using flame-hydrolysis deposition to bond a photosensitive fiber to a silica-on-silicon wafer, and a grating written using direct UV-writing. The laser operates on a single mode at the acetylene P13 line (1532.83 nm) with 9 mW output power. The noise properties of the laser are characterized demonstrating low linewidth operation (< 14 kHz) and superior relative intensity noise characteristics when compared to a commercial tunable external cavity diode laser. PMID:27137276

  8. DIAL monitoring of atmospheric climate-determining gases employing high-power pulsed laser diodes

    NASA Astrophysics Data System (ADS)

    Penchev, Stoyan P.; Naboko, Sergei V.; Naboko, Vassily N.; Pencheva, Vasilka H.; Donchev, T.; Pavlov, Lyubomir Y.; Simeonov, P.

    2003-11-01

    High-power pulsed laser diodes are employed for determining atmospheric humidity and methane. The proposed DIAL method optimizes the spectral properties of laser radiation within the molecular absorption bands of 0.86 - 0.9 μm of these major greenhouse gases. The explicit absorption spectrum is explored by computational convolution method based on reference data on spectral linestrengths modulated by the characteristic broad laser line of the selected laser diodes. The lidar scheme is ultimately compact, of low-energy consumption and suggests a large potential for ecological monitoring.

  9. Effect of thermal processes on critical operation conditions of high-power laser diodes

    NASA Astrophysics Data System (ADS)

    Parashchuk, V. V.; Doan Mien, Vu

    2013-10-01

    Using numerical and analytical techniques in a threedimensional approximation, we have modelled the effect of spatial thermoelastic stress nonuniformity in a laser diode - heat sink system on the output characteristics of the device in different operation modes. We have studied the influence of the pulse duration, the geometry of the laser system and its thermophysical parameters on the critical pump current density, in particular for state-of-the-art heat conductive substrate materials. The proposed approach has been used to optimise the laser diode assembly process in terms of the quality of laser crystal positioning (bonding) on a heat sink.

  10. Use of the 810 nm diode laser: soft tissue management and orthodontic applications of innovative technology.

    PubMed

    Sarver, David M

    2006-10-01

    Innovative technologies such as the diode laser have provided considerable benefit to dental patients and professionals. Facilitating efficient cutting of tissue and subsequent coagulation, the soft tissue laser enhances tissue healing and can reduce postsurgical complications. Due to the conservative nature of treatment accomplished with the laser this technology is very useful in orthodontic procedures. The diode laser is utilized in both esthetic enhancement of the smile, and treatment management of soft tissue issues that impede efficient orthodontic treatment. Its clinical application will be illustrated in a series of orthodontic cases. PMID:17139948

  11. Spatial Combining of Laser-Diode Beams for Pumping an NPRO

    NASA Technical Reports Server (NTRS)

    Gelsinger, Paul; Liu, Duncan; Mulder, Jerry; Aguayo, Francisco

    2008-01-01

    A free-space optical beam combiner now undergoing development makes it possible to use the outputs of multiple multimode laser diodes to pump a neodymium-doped yttrium aluminum garnet (Nd:YAG) non-planar ring oscillator (NPRO) laser while ensuring that the laser operates at only a single desired frequency. Heretofore, a Nd:YAG NPRO like the present one has been pumped by a single multimode laser-diode beam delivered via an optical fiber. It would be desirable to use multiple pump laser diodes to increase reliability beyond that obtainable from a single pump laser diode. However, as explained in this article, simplistically coupling multiple multimode laser-diode beams through a fiber-optic combiner would entail a significant reduction in coupling efficiency, and lasing would occur at one or more other frequencies in addition to the single desired frequency. To minimize coupling loss, one must ensure that the NA (approximately equal to 0.3) of the combined laser-diode beams is less than the NA of the fiber. The A(Omega) of the laser-diode beam in the slow-axis plane is 1/1.3 as large as that of the fiber. This A(Omega) is small enough to enable efficient coupling of light into the optical fiber, but too large for combining of beams in the slow-axis plane. Therefore, a pair of cylindrical lenses is used to cancel the slow-axis plane magnification introduced by the on-cylindrical lenses used to effect magnification in the fast-axis plane.

  12. Diode Laser Sensors for Arc-Jet Characterization

    NASA Technical Reports Server (NTRS)

    Hanson, Ronald K.

    2005-01-01

    The development and application of tunable diode laser (TDL) absorption sensors to monitor the health and operating conditions in the large-scale 60 MW arc-heated- plasma wind-tunnel at NASA Ames Research Center is reported. The interactive heating facility (THF) produces re-entry flow conditions by expanding the gas heated in a constricted plasma arc-heater to flow at high velocity over a model located in a test cabin. This facility provides the conditions needed to test thermal protective systems for spacecraft re-entering the earth s atmosphere. TDL sensors are developed to monitor gas flows in both the high-temperature constricted flow and the supersonic expansion flow into test cabin. These sensors utilize wavelength-tuned diode lasers to measure absorption transitions of atomic oxygen near 777.2 nm, atomic nitrogen near 856.8 nm, and atomic copper near 793.3 nm. The oxygen and nitrogen sensors measure the population density in exited electronic states of these atoms. The measurements combined with the assumption of local thermal and chemical equilibrium yield gas temperature (typically near 7,000K). The nitrogen and oxygen population temperatures are redundant, and their close agreement provides an important test of the local thermal equilibrium assumption. These temperature sensors provide time-resolved monitors of the operating conditions of the arc-heater and can be used to verify and control the test conditions. An additional TDL sensor was developed to monitor the copper concentration in the arc-heater flow yielding values as high as 13 ppm. Measurements of copper in the flow can identify flow conditions with unacceptably rapid electrode erosion, and hence this sensor provides valuable information needed to schedule maintenance to avoid costly arc-heater failure. TDL sensors were also developed for measurements in the test cabin, where absorption measurements of the populations of argon and molecular nitrogen in excited metastable electronic states

  13. GaAs Substrates for High-Power Diode Lasers

    NASA Astrophysics Data System (ADS)

    Mueller, Georg; Berwian, Patrick; Buhrig, Eberhard; Weinert, Berndt

    GaAs substrate crystals with low dislocation density (Etch-Pit Density (EPD) < 500,^-2) and Si-doping ( ~10^18,^-3) are required for the epitaxial production of high-power diode-lasers. Large-size wafers (= 3 mathrm{in} -> >=3,) are needed for reducing the manufacturing costs. These requirements can be fulfilled by the Vertical Bridgman (VB) and Vertical Gradient Freeze (VGF) techniques. For that purpose we have developed proper VB/VGF furnaces and optimized the thermal as well as the physico-chemical process conditions. This was strongly supported by extensive numerical process simulation. The modeling of the VGF furnaces and processes was made by using a new computer code called CrysVUN++, which was recently developed in the Crystal Growth Laboratory in Erlangen.GaAs crystals with diameters of 2 and 3in were grown in pyrolytic Boron Nitride (pBN) crucibles having a small-diameter seed section and a conical part. Boric oxide was used to fully encapsulate the crystal and the melt. An initial silicon content in the GaAs melt of c (melt) = 3 x10^19,^-3 has to be used in order to achieve a carrier concentration of n = (0.8- 2) x10^18,^-3, which is the substrate specification of the device manufacturer of the diode-laser. The EPD could be reduced to values between 500,^-2 and 50,^-2 with a Si-doping level of 8 x10^17 to 1 x10^18,^-3. Even the 3in wafers have rather large dislocation-free areas. The lowest EPDs ( <100,^-2) are achieved for long seed wells of the crucible.

  14. Diffractive Combiner of Single-Mode Pump Laser-Diode Beams

    NASA Technical Reports Server (NTRS)

    Liu, Duncan; Wilson, Daniel; Qiu, Yueming; Forouhar, Siamak

    2007-01-01

    An optical beam combiner now under development would make it possible to use the outputs of multiple single-mode laser diodes to pump a neodymium: yttrium aluminum garnet (Nd:YAG) nonplanar ring oscillator (NPRO) laser while ensuring that the laser operates at only a single desired frequency. Heretofore, an Nd:YAG NPRO like the present one has been pumped by a single multimode laser-diode beam delivered via an optical fiber. It would be desirable to use multiple pump laser diodes to increase reliability beyond that obtainable from a single pump laser diode. However, as explained below, simplistically coupling multiple multimode laser-diode beams through a fiber-optic combiner would entail a significant reduction in coupling efficiency, and lasing would occur at one or more other frequencies in addition to the single desired frequency. Figure 1 schematically illustrates the principle of operation of a laser-diode-pumped Nd:YAG NPRO. The laser beam path is confined in a Nd:YAG crystal by means of total internal reflections on the three back facets and a partial-reflection coating on the front facet. The wavelength of the pump beam - 808 nm - is the wavelength most strongly absorbed by the Nd:YAG crystal. The crystal can lase at a wavelength of either 1,064 nm or 1,319 nm - which one depending on the optical coating on the front facet. A thermal lens effect induced by the pump beam enables stable lasing in the lowest-order transverse electromagnetic mode (the TEM00 mode). The frequency of this laser is very stable because of the mechanical stability of the laser crystal and the unidirectional nature of the lasing. The unidirectionality is a result of the combined effects of (1) a Faraday rotation induced by an externally applied magnetic field and (2) polarization associated with non-normal incidence and reflection on the front facet.

  15. Diode-pumped Q-switched Nd{sup 3+} : YAG laser operating in a wide temperature range without thermal stabilisation of pump diodes

    SciTech Connect

    Vainshenker, A E; Vilenskiy, A V; Kazakov, A A; Lysoy, B G; Mikhailov, L K; Pashkov, V A

    2013-02-28

    A model sample of a compact low-power-consumption Nd{sup 3+} : YAG laser emitting 20-mJ pulses with a pulse repetition rate up to 20 Hz (in cyclic duty) at a wavelength of 1064 nm is developed and studied. The laser is designed for operating at external temperatures from -40 to +50 deg C. This was achieved by using quasi-end diode pumping without thermal stabilisation of pump diodes. (laser optics 2012)

  16. Optical coherence tomography-guided laser microsurgery for blood coagulation with continuous-wave laser diode

    NASA Astrophysics Data System (ADS)

    Chang, Feng-Yu; Tsai, Meng-Tsan; Wang, Zu-Yi; Chi, Chun-Kai; Lee, Cheng-Kuang; Yang, Chih-Hsun; Chan, Ming-Che; Lee, Ya-Ju

    2015-11-01

    Blood coagulation is the clotting and subsequent dissolution of the clot following repair to the damaged tissue. However, inducing blood coagulation is difficult for some patients with homeostasis dysfunction or during surgery. In this study, we proposed a method to develop an integrated system that combines optical coherence tomography (OCT) and laser microsurgery for blood coagulation. Also, an algorithm for positioning of the treatment location from OCT images was developed. With OCT scanning, 2D/3D OCT images and angiography of tissue can be obtained simultaneously, enabling to noninvasively reconstruct the morphological and microvascular structures for real-time monitoring of changes in biological tissues during laser microsurgery. Instead of high-cost pulsed lasers, continuous-wave laser diodes (CW-LDs) with the central wavelengths of 450 nm and 532 nm are used for blood coagulation, corresponding to higher absorption coefficients of oxyhemoglobin and deoxyhemoglobin. Experimental results showed that the location of laser exposure can be accurately controlled with the proposed approach of imaging-based feedback positioning. Moreover, blood coagulation can be efficiently induced by CW-LDs and the coagulation process can be monitored in real-time with OCT. This technology enables to potentially provide accurate positioning for laser microsurgery and control the laser exposure to avoid extra damage by real-time OCT imaging.

  17. Laser-diode-pumped, erbium-doped, solid-state laser with high slope efficiency

    SciTech Connect

    Esterowitz, L.; Allen, R.; Kintz, G.

    1989-10-31

    A laser and method for producing a laser emission at a wavelength of substantially 2.8 microns is disclosed. In a preferred embodiment of the invention, the laser comprises laser diode means for emitting a pump beam at a preselected wavelength; and a crystal having a preselected host material doped with a predetermined percent concentration of erbium activator ions sufficient to produce a laser emission at substantially 2.8 microns at a slope efficiency of at least 5 percent, but preferrably 10 percent, when the crystal is pumped by the pump beam. It is well known that the human body is comprised of approximately 70% water, with various human tissues containing about 60% to 90% of water, and bone and cartilage containing about 30% to 40% of water. Since the 2.8 micron wavelength has a substantially maximum absorption in water, this 2.8 micron wavelength is the ideal wavelength to use for a large variety of medical laser applications on the human body. A 2.8 micron wavelength laser could be used for precise surgery in such exemplary applications as brain surgery, neurosurgery, eye surgery, plastic surgery, burn treatment and the removal of malignancies.

  18. Optical coherence tomography-guided laser microsurgery for blood coagulation with continuous-wave laser diode

    PubMed Central

    Chang, Feng-Yu; Tsai, Meng-Tsan; Wang, Zu-Yi; Chi, Chun-Kai; Lee, Cheng-Kuang; Yang, Chih-Hsun; Chan, Ming-Che; Lee, Ya-Ju

    2015-01-01

    Blood coagulation is the clotting and subsequent dissolution of the clot following repair to the damaged tissue. However, inducing blood coagulation is difficult for some patients with homeostasis dysfunction or during surgery. In this study, we proposed a method to develop an integrated system that combines optical coherence tomography (OCT) and laser microsurgery for blood coagulation. Also, an algorithm for positioning of the treatment location from OCT images was developed. With OCT scanning, 2D/3D OCT images and angiography of tissue can be obtained simultaneously, enabling to noninvasively reconstruct the morphological and microvascular structures for real-time monitoring of changes in biological tissues during laser microsurgery. Instead of high-cost pulsed lasers, continuous-wave laser diodes (CW-LDs) with the central wavelengths of 450 nm and 532 nm are used for blood coagulation, corresponding to higher absorption coefficients of oxyhemoglobin and deoxyhemoglobin. Experimental results showed that the location of laser exposure can be accurately controlled with the proposed approach of imaging-based feedback positioning. Moreover, blood coagulation can be efficiently induced by CW-LDs and the coagulation process can be monitored in real-time with OCT. This technology enables to potentially provide accurate positioning for laser microsurgery and control the laser exposure to avoid extra damage by real-time OCT imaging. PMID:26568136

  19. Laser diode pumped, erbium-doped, solid state laser with high slope efficiency

    NASA Astrophysics Data System (ADS)

    Esterowitz, Leon; Allen, R.; Kintz, G.

    1989-10-01

    A laser and method for producing a laser emission at a wavelength of substantially 2.8 microns is disclosed. In a preferred embodiment of the invention, the laser comprises laser diode means for emitting a pump beam at a preselected wavelength; and a crystal having a preselected host material doped with a predetermined percent concentration of erbium activator ions sufficient to produce a laser emission at substantially 2.8 microns at a slope efficiency of at least 5 percent, but preferrably 10 percent, when the crystal is pumped by the pump beam. It is well known that the human body is comprised of approximately 70 percent water, with various human tissues containing about 60 to 90 percent of water, and bone and cartilage containing about 30 to 40 percent of water. Since the 2.8 micron wavelength has a substantially maximum absorption in water, this 2.8 micron wavelength is the ideal wavelength to use for a large variety of medical laser applications on the human body. A 2.8 micron wavelength laser could be used for precise surgery in such exemplary applications as brain surgery, neurosurgery, eye surgery, plastic surgery, burn treatment, and the removal of malignancies.

  20. Temperature evaluation of dental implant surface irradiated with high-power diode laser.

    PubMed

    Rios, F G; Viana, E R; Ribeiro, G M; González, J C; Abelenda, A; Peruzzo, D C

    2016-09-01

    The prevalence of peri-implantitis and the absence of a standard approach for decontamination of the dental implant surface have led to searches for effective therapies. Since the source of diode lasers is portable, has reduced cost, and does not cause damage to the titanium surface of the implant, high-power diode lasers have been used for this purpose. The effect of laser irradiation on the implants is the elevation of the temperature surface. If this elevation exceeds 47 °C, the bone tissue is irreversibly damaged, so for a safety therapy, the laser parameters should be controlled. In this study, a diode laser of GaAsAl was used to irradiate titanium dental implants, for powers 1.32 to 2.64 W (real) or 2.00 to 4.00 W (nominal), in continuous/pulsed mode DC/AC, with exposure time of 5/10 s, with/without air flow for cooling. The elevation of the temperature was monitored in real time in two positions: cervical and apical. The best results for decontamination using a 968-nm diode laser were obtained for a power of 1.65 and 1.98 W (real) for 10 s, in DC or AC mode, with an air flow of 2.5 l/min. In our perspective in this article, we determine a suggested approach for decontamination of the dental implant surface using a 968-nm diode laser. PMID:27365109

  1. Generation of high-power nanosecond pulses from laser diode-pumped Nd:YAG lasers

    NASA Technical Reports Server (NTRS)

    Chan, Kinpui

    1988-01-01

    Simulation results are used to compare the pulse energy levels and pulse energy widths that can be achieved with LD-pumped Nd:YAG lasers for both the pulse-transmission mode (PTM) and pulse-reflection mode (PRM) Q-switching methods for pulse energy levels up to hundreds of microjoules and pulse widths as short as 1 ns. It is shown that high-power pulses with pulse widths as short as 1 ns can be generated with PTM Q-switched in LD-pumped Nd:YAG lasers. With the PRM Q-switching method, pulse widths as short as 2 ns and pulse energy at the level of a few hundred microjoules can also be achieved but require pumping with 8-10-mJ AlGaAs laser diode arrays.

  2. Tm,Ho:YLF laser end-pumped by a semiconductor diode laser array

    NASA Technical Reports Server (NTRS)

    Hemmati, Hamid (Inventor)

    1990-01-01

    An Ho:YLF crystal including Tm as sensitizers for the activator Ho, is optically pumped with a semiconductor diode laser array to generate 2.1 micron radiation with a pump power to output power of efficiency as high as 68 percent. The prior-art dual sensitizer system of Er and Tm requires cooling, such as by LN2, but by using Tm alone and decreasing the concentrations of Tm and Ho, and decreasing the length of the laser rod to about 1 cm, it has been demonstrated that laser operation can be obtained from a temperature of 77 K with an efficiency as high as 68 percent up to ambient room temperature with an efficiency at that temperature as high as 9 percent.

  3. Continuously tunable single-frequency 1.52-{mu}m diode laser for gas analysis

    SciTech Connect

    Gladyshev, A V; Belovolov, M I; Vasil'ev, Sergei A; Medvedkov, O I; Duraev, V P; Nedelin, E T; Nadezhdinskii, Aleksandr I; Ponurovskii, Ya Ya

    2005-03-31

    A single-frequency continuously tunable diode laser with a hybrid fibre Bragg grating resonator (hybrid laser) is built for recording the absorption line of ammonia. The continuous tuning within 40 GHz (1.33 cm{sup -1}) was achieved for the first time for a hybrid laser emitting 5 mW in the line of width {delta}{nu} {<=} 15 MHz (0.0005 cm{sup -1}) with the side-mode suppression exceeding 20 dB. (lasers)

  4. In Vitro Study of Dentin Hypersensitivity Treated by 980-nm Diode Laser

    PubMed Central

    Liu, Ying; Gao, Jie; Gao, Yan; XU, Shuaimei; Zhan, Xueling; Wu, Buling

    2013-01-01

    Introduction: To investigate the ultrastructural changes of dentin irradiated with 980-nm diode laser under different parameters and to observe the morphological alterations of odontoblasts and pulp tissue to determine the safety parameters of 980-nm diode laser in the treatment of dentin hypersensitivity (DH). Methods: Twenty extracted human third molars were selected to prepare dentin discs. Each dentin disc was divided into four areas and was irradiated by 980-nm diode laser under different parameters: Group A: control group, 0 J/cm2; Group B: 2 W/CW (continuous mode), 166 J/cm2; Group C: 3W/CW, 250 J/cm2; and Group D: 4W/CW, 333 J/cm2. Ten additional extracted human third molars were selected to prepare dentin discs. Each dentin disc was divided into two areas and was irradiated by 980-nm diode laser: Group E: control group, 0 J/cm2; and Group F: 2.0 W/CW, 166 J/cm2. The morphological alterations of the dentin surfaces and odontoblasts were examined with scanning electron microscopy (SEM), and the morphological alterations of the dental pulp tissue irradiated by laser were observed with an upright microscope. Results: The study demonstrated that dentinal tubules can be entirely blocked after irradiation by 980-nm diode laser, regardless of the parameter setting. Diode laser with settings of 2.0 W and 980-nm sealed exposed dentin tubules effectively, and no significant morphological alterations of the pulp and odontoblasts were observed after irradiation. Conclusions: Irradiation with 980-nm diode laser could be effective for routine clinical treatment of DH, and 2.0W/CW (166 J/cm2) was a suitable energy parameter due to its rapid sealing of the exposed dentin tubules and its safety to the odontoblasts and pulp tissue. PMID:25606318

  5. Space certification and qualification programs for laser diode modules on the NASA ICESat-2 Mission

    NASA Astrophysics Data System (ADS)

    Sawruk, Nicholas W.; Stephen, Mark A.; Bruce, Kevin; Eltringham, Thomas F.; Nash, Franklin R.; Piccirilli, Alfonso B.; Slusark, Walter J.; Hovis, Floyd E.

    2013-09-01

    A laser diode module (LDM) space certification and qualification program was developed for NASA's Ice, Cloud and Land Elevation Satellite-2, ICESat-2 mission. The ICESat-2 laser transmitter is a high performance diode-pumped solid state laser that requires high reliability, high efficiency and high brightness fiber coupled LDMs, capable of supporting a 27,000 hour mission life. The test centric LDM space certification and qualification programs consisted of several key phases including a technology plausibility study, laser diode and LDM pedigree reviews, environmental acceptance and qualification testing, and extensive life testing. The intent of the plausibility study was to analytically and experimentally demonstrate that a commercial-off-the-shelf (COTS) LDM design was capable of being space-certified. A pedigree review of the laser diode population was conducted to reject out-of-family laser diodes from the population. The laser diode pedigree review was a statistical analysis of several laser diode performance metrics (efficiency, operating current, etc.) with outliers being rejected. All LDMs underwent environmental acceptance testing including vibration, thermal cycling and an extended burn-in. The primary purpose of the acceptance testing was to highlight internal workmanship issues. The pedigree review of the acceptance tested LDMs was conducted to reject out-of-family LDMs in statistical analysis of several performance metrics (operating current, coupling efficiency, etc.). A sub-set of the flight-certified LDMs will be exposed to environmental qualification testing and will subsequently be tested to failure to determine the LDM capability. Multiple LDMs are being life tested under flight-like conditions and show no signs of degradation with run times of 22,000 hours, which is over 80% of the mission life. Details of the LDMs space certification and qualification programs are presented.

  6. Management of Chronic Periodontitis Using Chlorhexidine Chip and Diode Laser-A Clinical Study

    PubMed Central

    Ambooken, Majo; Mathew, Jayan Jacob; Issac, Annie Valayil; Kunju, Ajithkumar Parachalil; Parameshwaran, Renjith Athirkandathil

    2016-01-01

    Introduction The use of adjuncts like chlorhexidine local delivery and diode laser decontamination have been found to improve the clinical outcomes of scaling and root planing in non-surgical periodontal therapy in patients with chronic periodontitis. Aim To evaluate the effects of diode laser and chlorhexidine chip as adjuncts to scaling and root planing in the management of chronic periodontitis. The objective is to evaluate the outcome of chlorhexidine chip and diode laser as adjuncts to scaling and root planing on clinical parameters like Plaque Index, Gingival Index, probing pocket depth and clinical attachment level. Study and Design Department of Periodontics. Randomized clinical trial with split mouth design. Materials and Methods Fifteen chronic periodontitis patients having a probing pocket depth of 5mm-7mm on at least one interproximal site in each quadrant of the mouth were included in the study. After initial treatment, four sites in each patient were randomly subjected to scaling and root planing (control), chlorhexidine chip application (CHX chip group), diode laser (810 nm) decontamination (Diode laser group) or combination of both (Diode laser and chip group). Plaque Index (PI), Gingival Index (GI), probing pocket depth (PPD) and clinical attachment level (CAL) were assessed at baseline, one month and three months. Statistical analysis Results were statistically analysed using paired T test, one-way ANOVA, Tukey’s HSD test and repeated measure ANOVA. Results Post-treatment, the test and control sites showed a statistically significant reduction in PI, GI, PPD, and CAL. After three months, a mean PPD reduction of 1.47±0.52 mm in control group, 1.40±0.83 mm in diode laser group, 2.67±0.62 mm in CHX group, and 2.80± 0.77 mm in combination group was seen. The mean gain in CAL were 1.47±0.52 mm in the control group, 1.40±0.83 mm in diode laser group, 2.67± 0.49 mm in CHX group and 2.67± 0.82 mm in combination group respectively. The

  7. Multi-kW high-brightness fiber coupled diode laser based on two dimensional stacked tailored diode bars

    NASA Astrophysics Data System (ADS)

    Bayer, Andreas; Unger, Andreas; Köhler, Bernd; Küster, Matthias; Dürsch, Sascha; Kissel, Heiko; Irwin, David A.; Bodem, Christian; Plappert, Nora; Kersten, Maik; Biesenbach, Jens

    2016-03-01

    The demand for high brightness fiber coupled diode laser devices in the multi kW power region is mainly driven by industrial applications for materials processing, like brazing, cladding and metal welding, which require a beam quality better than 30 mm x mrad and power levels above 3kW. Reliability, modularity, and cost effectiveness are key factors for success in the market. We have developed a scalable and modular diode laser architecture that fulfills these requirements through use of a simple beam shaping concept based on two dimensional stacking of tailored diode bars mounted on specially designed, tap water cooled heat sinks. The base element of the concept is a tailored diode laser bar with an epitaxial and lateral structure designed such that the desired beam quality in slow-axis direction can be realized without using sophisticated beam shaping optics. The optical design concept is based on fast-axis collimator (FAC) and slow-axis collimator (SAC) lenses followed by only one additional focusing optic for efficient coupling into a 400 μm fiber with a numerical aperture (NA) of 0.12. To fulfill the requirements of scalability and modularity, four tailored bars are populated on a reduced size, tap water cooled heat sink. The diodes on these building blocks are collimated simply via FAC and SAC. The building blocks can be stacked vertically resulting in a two-dimensional diode stack, which enables a compact design of the laser source with minimum beam path length. For a single wavelength, up to eight of these building blocks, implying a total of 32 tailored bars, can be stacked into a submodule, polarization multiplexed, and coupled into a 400 μm, 0.12NA fiber. Scalability into the multi kW region is realized by wavelength combining of replaceable submodules in the spectral range from 900 - 1100 nm. We present results of a laser source based on this architecture with an output power of more than 4 kW and a beam quality of 25 mm x mrad.

  8. Laparoscopic Partial Nephrectomy with Diode Laser: A Promising Technique

    PubMed Central

    Knezevic, Nikola; Maric, Marjan; Grkovic, Marija Topalovic; Krhen, Ivan; Kastelan, Zeljko

    2014-01-01

    Abstract Objective: The aim of this study was to evaluate application of diode laser in laparoscopic partial nephrectomy (LPN), and to question this technique in terms of ease of tumor excision and reduction of warm ischemia time (WIT). Background data: LPN is the standard operative method for small renal masses. The benefits of LPN are numerous, including preserving renal function and prolonging overall survival. However, reduction of WIT remains main challenge in this operation. In order to shorten WIT, many techniques have been developed, with variable results. Patients and methods: We performed a prospective collection and analysis of health records for patients who were operated on between March 2011 and August 2012. Inclusion criteria were single tumor ≤4 cm, predominant exophytic growth and intraparenchymal depth ≤1.5 cm, with a minimum distance of 5 mm from the urinary collecting system. Results: We operated on 17 patients. Median operative time was 170 min. In all but two patients, we had to perform hilar clamping. Median duration of WIT was 16 min. Pathohistological evaluation revealed clear cell renal cancer and confirmed margins negative for tumor in all cases. Median size of the tumor was 3 cm. Median postoperative hospitalization was 5 days. Average follow up was 11.5 months. There were no intraoperative complications. One postoperative complication was noted: perirenal hematoma. Conclusions: Laser LPN is feasible, and offers the benefit of shorter WIT, with effective tissue coagulation and hemostasis. With operative experience and technical advances, WIT will be reduced or even eliminated, and a solution to some technical difficulties, such as significant smoke production, will be found. PMID:24460067

  9. High-density pulsed laser diode arrays for SSL pumping

    NASA Astrophysics Data System (ADS)

    Feeler, Ryan; Stephens, Edward

    2010-04-01

    Northrop Grumman Cutting Edge Optronics has developed a new laser diode array package with minimal bar-to-bar spacing. These High Density Stack (HDS) packages allow for a power density increase on the order of ~ 2.5x when compared to industry-standard arrays. This work contains an overview of the manufacturing process, as well as representative data for 5-, 10-, and 20-bar arrays. Near-field and power vs. current data is presented in each case. Power densities approaching 15 kW/cm2 are presented. In addition, power and wavelength are presented as a function of pulse width in order to determine the acceptable operational parameters for this type of array. In the low repetition rate Nd:YAG pumping regime, all devices are shown to operate with relatively low junction temperatures. A discussion of future work is also presented, with a focus on extending the HDS architecture to reliable operation at 300W per bar. This will enable power densities of approximately 25 kW/cm2.

  10. Microgravity Diode Laser Spectroscopy Measurements in a Reacting Vortex Ring

    NASA Technical Reports Server (NTRS)

    Chen, Shin-Juh; Dahm, Werner J. A.; Silver, Joel A.; Piltch, Nancy D.

    2001-01-01

    The technique of Diode Laser Spectroscopy (DLS) with wavelength modulation is utilized to measure the concentration of methane in reacting vortex rings under microgravity conditions. From the measured concentration of methane, other major species such as water, carbon dioxide, nitrogen, and oxygen can be easily computed under the assumption of equilibrium chemistry with the method of Interactive Temperature with Assumed Chemistry (ITAC). The conserved scalar approach in modelling the coupling between fluid dynamics and combustion is utilized to represent the unknown variables in terms of the mixture fraction and scalar dissipation rate in conjunction with ITAC. Post-processing of the DLS measurements and the method of ITAC used in computing the species concentration are discussed. From the flame luminosity results, the increase in ring circulation appears to increase the fuel consumption rate inside the reacting vortex ring and the flame height for cases with similar fuel volumes. Preliminary results and application of ITAC show some potential capabilities of ITAC in DLS. The measured concentration of methane, and computed concentrations of water and carbon dioxide agree well with available results from numerical simulations.

  11. Brightness and average power as driver for advancements in diode lasers and their applications

    NASA Astrophysics Data System (ADS)

    Hengesbach, Stefan; Poprawe, Reinhart; Hoffmann, Dieter; Traub, Martin; Schwarz, Thomas; Holly, Carlo; Eibl, Florian; Weisheit, Andreas; Vogt, Sabrina; Britten, Simon; Ungers, Michael; Thombansen, Ulrich; Engelmann, Christoph; Mamuschkin, Viktor; Lott, Philipp

    2015-03-01

    Spatial and spectral emission characteristics and efficiency of high-power diode laser (HPDL) based pump sources enable and define the performance of the fundamental solid state laser concepts like disk, fiber and slab lasers. HPDL are also established as a versatile tool for direct materials processing substituting other laser types like CO2 lasers and lamp pumped solid state lasers and are starting to substitute even some of the diode pumped solid state lasers. Both, pumping and direct applications will benefit from the further improvement of the brightness and control of the output spectrum of HPDL. While edge emitting diodes are already established, a new generation of vertical emitting diode lasers (VCSELs) made significant progress and provides easy scalable output power in the kW range. Beneficial properties are simplified beam shaping, flexible control of the temporal and spatial emission, compact design and low current operation. Other characteristics like efficiency and brightness of VCSELs are still lagging behind the edge emitter performance. Examples of direct applications like surface treatment, soldering, welding, additive manufacturing, cutting and their requirements on the HPDL performance are presented. Furthermore, an overview on process requirements and available as well as perspective performance of laser sources is derived.

  12. Diode-Pumped Alkali Atom Lasers 03-LW-024 Final Report

    SciTech Connect

    Page, R H; Beach, R J

    2005-02-16

    The recent work at LLNL on alkali-atom lasers has been remarkably successful and productive. Three main phases (so far) can be identified. First, the concept and demonstration of red lasers using (Ti:sapphire pumping) took place; during this time, Rubidium and Cesium resonance-line lasers were tested, and theoretical models were developed and shown to describe experimental results very reliably. Work done during this first phase has been well documented, and the models from that period are still in use for their predictions and for designing power-scaled lasers. [1 - 3] Second, attempts were made to produce a blue alkali-vapor laser using sequentially-resonant two-step pumping (again, using Ti:sapphire lasers.) Although a blue laser did not result, the physical limitations of our approach are now better-defined. Third, diode-pumped operation of a red laser (Rubidium) was attempted, and we eventually succeeded in demonstrating the world's first diode-pumped gas laser. [4] Because we have a defensible concept for producing an efficient, compact, lightweight, power-scaled laser (tens of kW,) we are in a position to secure outside funding, and would like to find a sponsor. For descriptions of work done during the ''first phase,'' see References [1 - 3] ''Phase two'' work is briefly described in the section ''Blue laser,'' and ''phase three'' work is presented in the section entitled ''Diode-pumped red laser.''

  13. Direct diode lasers and their advantages for materials processing and other applications

    NASA Astrophysics Data System (ADS)

    Fritsche, Haro; Ferrario, Fabio; Koch, Ralf; Kruschke, Bastian; Pahl, Ulrich; Pflueger, Silke; Grohe, Andreas; Gries, Wolfgang; Eibl, Florian; Kohl, Stefanie; Dobler, Michael

    2015-03-01

    The brightness of diode lasers is improving continuously and has recently started to approach the level of some solid state lasers. The main technology drivers over the last decade were improvements of the diode laser output power and divergence, enhanced optical stacking techniques and system design, and most recently dense spectral combining. Power densities at the work piece exceed 1 MW/cm2 with commercially available industrial focus optics. These power densities are sufficient for cutting and welding as well as ablation. Single emitter based diode laser systems further offer the advantage of fast current modulation due their lower drive current compared to diode bars. Direct diode lasers may not be able to compete with other technologies as fiber or CO2-lasers in terms of maximum power or beam quality. But diode lasers offer a range of features that are not possible to implement in a classical laser. We present an overview of those features that will make the direct diode laser a very valuable addition in the near future, especially for the materials processing market. As the brightness of diode lasers is constantly improving, BPP of less than 5mm*mrad have been reported with multikW output power. Especially single emitter-based diode lasers further offer the advantage of very fast current modulation due to their low drive current and therefore low drive voltage. State of the art diode drivers are already demonstrated with pulse durations of <10μs and repetition rates can be adjusted continuously from several kHz up to cw mode while addressing power levels from 0-100%. By combining trigger signals with analog modulations nearly any kind of pulse form can be realized. Diode lasers also offer a wide, adaptable range of wavelengths, and wavelength stabilization. We report a line width of less than 0.1nm while the wavelength stability is in the range of MHz which is comparable to solid state lasers. In terms of applications, especially our (broad) wavelength

  14. In Vitro Comparison of the Effects of Diode Laser and CO2 Laser on Topical Fluoride Uptake in Primary Teeth

    PubMed Central

    Bahrololoomi, Zahra; Sorouri, Milad

    2015-01-01

    Objectives: Fluoride therapy is important for control and prevention of dental caries. Laser irradiation can increase fluoride uptake especially when combined with topical fluoride application. The objective of this study was to compare the effects of CO2 and diode lasers on enamel fluoride uptake in primary teeth. Materials and Methods: Forty human primary molars were randomly assigned to four groups (n=10). The roots were removed and the crowns were sectioned mesiodistally into buccal and lingual halves as the experimental and control groups. All samples were treated with 5% sodium fluoride (NaF) varnish. The experimental samples in the four groups were irradiated with 5 or 7W diode or 1 or 2W CO2 laser for 15 seconds and were compared with the controls in terms of fluoride uptake, which was determined using an ion selective electrode after acid dissolution of the specimens. Data were analyzed by SPSS version 16 using ANOVA treating the control measurements as covariates. Results: The estimated amount of fluoride uptake was 59.5± 16.31 ppm, 66.5± 14.9 ppm, 78.6± 12.43 ppm and 90.4± 11.51 ppm for 5W and 7 W diode and 1W and 2 W CO2 lasers, respectively, which were significantly greater than the values in the conventional topical fluoridation group (P<0.005). There were no significant differences between 7W diode laser and 1W CO2 laser, 5W and 7W diode laser, or 1W and 2W CO2 laser in this regard. Conclusion: The results showed that enamel surface irradiation by CO2 and diode lasers increases the fluoride uptake. PMID:27123018

  15. High-Power Broad-Area Diode Lasers and Laser Bars

    NASA Astrophysics Data System (ADS)

    Erbert, Goetz; Baerwolff, Arthur; Sebastian, Juergen; Tomm, Jens

    This review presents the basic ideas and some examples of the chip technology of high-power diode lasers ( λ= 650,-1060,) in connection with the achievements of mounted single-stripe emitters in recent years.In the first section the optimization of the epitaxial layer structure for a low facet load and high conversion efficiency is discussed. The so-called broadened waveguide Large Optical Cavity (LOC) concept is described and also some advantages and disadvantages of Al-free material. The next section deals with the processing steps of epitaxial wafers to make single emitters and bars. Several possibilities to realize contact windows (implantation, insulators, and wet chemical oxidation) and laser mirrors are presented. The impact of heating in the CW regime and some aspects of reliability are the following topics. The calculation of thermal distributions in diode lasers, which shows the need for sophisticated mounting, will be given. In the last part the current state-of-the-art of single-stripe emitters will be reviewed.

  16. 1064 nm laser emission of highly doped Nd: Yttrium aluminum garnet under 885 nm diode laser pumping

    NASA Astrophysics Data System (ADS)

    Lupei, V.; Pavel, N.; Taira, T.

    2002-06-01

    Highly efficient 1064 nm continuous-wave laser emission under 885 nm diode pumping in concentrated Nd: Yttrium aluminum garnet (YAG) crystals (up to 3.5 at. % Nd) and ceramics (up to 3.8 at. % Nd) is reported. A highly doped (2.4 at. %) Nd:YAG laser, passively Q switched by a Cr4+:YAG saturable absorber, is demonstrated.

  17. Simple gain form of 1.5 µm multimode laser diode incorporating band filling and intrinsic gain saturation effects

    NASA Astrophysics Data System (ADS)

    Wada, Kenji; Matsuyama, Tetsuya; Horinaka, Hiromichi

    2015-03-01

    The gain form of a 1.5 µm multimode laser diode was derived by phenomenologically adding an intrinsic gain saturation term to the linearized gain form described in our previous report. Although the proposed gain form was simple, it almost perfectly matched the complex laser diode gain in a direct transition model implicitly incorporating both band filling and intrinsic gain saturation effects. Using laser diode rate equations including the proposed gain form, the characteristic power spectrum of a gain-switched pulse from a 1.5 µm multimode laser diode was successfully simulated.

  18. Watt-level red-emitting diode lasers and modules for display applications

    NASA Astrophysics Data System (ADS)

    Paschke, Katrin; Blume, Gunnar; Feise, David; Pohl, Johannes; Sumpf, Bernd

    2016-02-01

    Red-emitting lasers for display applications require high output powers and a high visibility. We demonstrate diode lasers and modules in the red spectral range based on AlGaInP with optical output powers up to 1 W and a nearly diffraction limited beam. These high-luminance light sources based on tapered lasers are well suited for laser TVs and projectors for virtual reality simulators based on the flying spot technology. Additionally, we developed diode lasers with internal distributed Bragg reflector (DBR) surface gratings. These DBR tapered lasers and master-oscillator power-amplifiers based on DBR ridge-waveguide lasers and tapered amplifiers feature high power, single mode emission with coherence lengths up to several meters, which are suitable for the next-generation 3D displays based on holography.

  19. Construction and Characterization of External Cavity Diode Lasers for Atomic Physics

    PubMed Central

    Hardman, Kyle S.; Bennetts, Shayne; Debs, John E.; Kuhn, Carlos C. N.; McDonald, Gordon D.; Robins, Nick

    2014-01-01

    Since their development in the late 1980s, cheap, reliable external cavity diode lasers (ECDLs) have replaced complex and expensive traditional dye and Titanium Sapphire lasers as the workhorse laser of atomic physics labs1,2. Their versatility and prolific use throughout atomic physics in applications such as absorption spectroscopy and laser cooling1,2 makes it imperative for incoming students to gain a firm practical understanding of these lasers. This publication builds upon the seminal work by Wieman3, updating components, and providing a video tutorial. The setup, frequency locking and performance characterization of an ECDL will be described. Discussion of component selection and proper mounting of both diodes and gratings, the factors affecting mode selection within the cavity, proper alignment for optimal external feedback, optics setup for coarse and fine frequency sensitive measurements, a brief overview of laser locking techniques, and laser linewidth measurements are included. PMID:24796259

  20. Construction and characterization of external cavity diode lasers for atomic physics.

    PubMed

    Hardman, Kyle S; Bennetts, Shayne; Debs, John E; Kuhn, Carlos C N; McDonald, Gordon D; Robins, Nick

    2014-01-01

    Since their development in the late 1980s, cheap, reliable external cavity diode lasers (ECDLs) have replaced complex and expensive traditional dye and Titanium Sapphire lasers as the workhorse laser of atomic physics labs. Their versatility and prolific use throughout atomic physics in applications such as absorption spectroscopy and laser cooling makes it imperative for incoming students to gain a firm practical understanding of these lasers. This publication builds upon the seminal work by Wieman, updating components, and providing a video tutorial. The setup, frequency locking and performance characterization of an ECDL will be described. Discussion of component selection and proper mounting of both diodes and gratings, the factors affecting mode selection within the cavity, proper alignment for optimal external feedback, optics setup for coarse and fine frequency sensitive measurements, a brief overview of laser locking techniques, and laser linewidth measurements are included. PMID:24796259

  1. Injection locking of a low cost high power laser diode at 461 nm.

    PubMed

    Pagett, C J H; Moriya, P H; Celistrino Teixeira, R; Shiozaki, R F; Hemmerling, M; Courteille, Ph W

    2016-05-01

    Stable laser sources at 461 nm are important for optical cooling of strontium atoms. In most existing experiments, this wavelength is obtained by frequency doubling infrared lasers, since blue laser diodes either have low power or large emission bandwidths. Here, we show that injecting less than 10 mW of monomode laser radiation into a blue multimode 500 mW high power laser diode is capable of slaving at least 50% of the power to the desired frequency. We verify the emission bandwidth reduction by saturation spectroscopy on a strontium gas cell and by direct beating of the slave with the master laser. We also demonstrate that the laser can efficiently be used within the Zeeman slower for optical cooling of a strontium atomic beam. PMID:27250390

  2. Injection locking of a low cost high power laser diode at 461 nm

    NASA Astrophysics Data System (ADS)

    Pagett, C. J. H.; Moriya, P. H.; Celistrino Teixeira, R.; Shiozaki, R. F.; Hemmerling, M.; Courteille, Ph. W.

    2016-05-01

    Stable laser sources at 461 nm are important for optical cooling of strontium atoms. In most existing experiments, this wavelength is obtained by frequency doubling infrared lasers, since blue laser diodes either have low power or large emission bandwidths. Here, we show that injecting less than 10 mW of monomode laser radiation into a blue multimode 500 mW high power laser diode is capable of slaving at least 50% of the power to the desired frequency. We verify the emission bandwidth reduction by saturation spectroscopy on a strontium gas cell and by direct beating of the slave with the master laser. We also demonstrate that the laser can efficiently be used within the Zeeman slower for optical cooling of a strontium atomic beam.

  3. Effect of Diode Laser Irradiation Combined with Topical Fluoride on Enamel Microhardness of Primary Teeth

    PubMed Central

    Bahrololoomi, Zahra; Lotfian, Malihe

    2015-01-01

    Objectives: Laser irradiation has been suggested as an adjunct to traditional caries prevention methods. But little is known about the cariostatic effect of diode laser and most studies available are on permanent teeth.The purpose of the present study was to investigate the effect of diode laser irradiation combined with topical fluoride on enamel surface microhardness. Materials and Methods: Forty-five primary teeth were used in this in vitro study. The teeth were sectioned to produce 90 slabs. The baseline Vickers microhardness number of each enamel surface was determined. The samples were randomly divided into 3 groups. Group 1: 5% NaF varnish, group 2: NaF varnish+ diode laser at 5 W power and group 3: NaF varnish+ diode laser at 7 W power. Then, the final microhardness number of each surface was again determined. The data were statistically analyzed by repeated measures ANOVA at 0.05 level of significance. Results: In all 3 groups, microhardness number increased significantly after surface treatment (P<0.05). However, Microhardness change after treatment was not significantly different among groups (P >0.05). Conclusion: The combined application of diode laser and topical fluoride varnish on enamel surface did not show any significant additional effect on enamel resistance to caries. PMID:26056517

  4. Triggering GaAs lock-on switches with laser diode arrays

    SciTech Connect

    Loubriel, G.M.; Buttram, M.T.; Helgeson, W.D.; McLaughlin, D.L.; O'Malley, M.W.; Zutavern, F.J. ); Rosen, A.; Stabile, P.J. )

    1990-01-01

    Laser diode arrays have been used to trigger GaAs Photoconducting Semiconductor Switches (PCSS) charged to voltages of up to 60 kV and conducting currents of 580 A. The driving forces behind the use of laser diode arrays are compactness, elimination of complicated optics, and the ability to run at high repetition rates. Laser diode arrays are compactness, elimination of complicated optics, and the ability to run at high repetition rates. Laser diode arrays can trigger GaAs at high fields as the result of a new switching mode (lock-on) with very high carrier number gain. We have achieved switching of up to 10 MW in a 60 {Omega} system, with a pulse rise time of 500 ps. At 1.2 MW we have achieved repetition rates of 1 kHz with switch rise time of 500 ps for 10{sup 5} shots. The laser diode array used for these experiments delivers a 166 W pulse. In a single shot mode we have switched 4 kA with a flash lamp pumped laser and 600 A with the 166 W array. 7 refs., 5 figs.

  5. The LUCIA project: a high average power ytterbium diode pumped solid state laser chain

    NASA Astrophysics Data System (ADS)

    Bourdet, Gilbert L.; Chanteloup, Jean-Christophe; Fulop, A.; Julien, Y.; Migus, Arnold

    2004-04-01

    With the goal to set up a high average power Diode Pumped Solid State Laser (100 Joules/10 Hz/10 ns), the Laboratory for Use of Intense Laser (LULI) is now studying various solutions concerning the amplifier medium, the cooling, the pumping and the extraction architectures. In this paper, we present the last states of these developments and the solutions already chosen.

  6. Evaluation of the Diode laser (810nm,980nm) on dentin tubule diameter following internal bleaching

    PubMed Central

    Kiomarsi, Nazanin; Salim, Soheil; Sarraf, Pegah; Javad-Kharazifard, Mohammad

    2016-01-01

    Background The aim of this study was to evaluate the effect of diode laser irradiation and bleaching materials on the dentinal tubule diameter after laser bleaching. Material and Methods The dentin discs of 40 extracted third molar were used in this experiment. Each disc surface was divided into two halves by grooving. Half of samples were laser bleached at different wavelengths with two different concentrations of hydrogen peroxide. Other half of each disc with no laser bleaching remained as a negative control. Dentin discs were assigned randomly into four groups (n=10) with following hydrogen peroxide and diode laser wavelength specifications; Group 1 (30% - 810 nm), group 2 (30% - 980 nm), group 3 (46% - 810 nm) and group 4 (46% - 980 nm). All specimens were sent for scanning electron microscopic (SEM) analysis in order to measure tubular diameter in laser treated and control halves. Data were analyzed by ANOVA and Tukey test (p<0.05). Results A significant reduction in dentin tubule diameter was observed in groups 1, 2 and 4. There was no significant difference between groups 1 and 2 and between groups 3 and 4 after bleaching. Conclusions The SEM results showed that diode laser was able to reduce dentin tubule diameter and its effect on dentin was dependent on chemical action of bleaching material. Key words:Laser, diode, dentin, tubule, diameter. PMID:27398172

  7. Diode laser threshold current density and lasing wavelength as functions of active region thickness

    SciTech Connect

    Streifer, W.; Scifres, D.R.; Burnham, R.D.

    1983-03-01

    Based on a simple model of the band-to-band absorption of a diode laser active region, we formulatean expression for modal gain as a function of pumping current. Using this result yields expressions for threshold current density and lasing photon energy which depend on device parameters including active region thickness, laser length, internal losses, facet reflectivity, etc.

  8. Using a diode laser to uncover dental implants in second-stage surgery.

    PubMed

    Yeh, Sam; Jain, Kamlesh; Andreana, Sebastiano

    2005-01-01

    A soft tissue diode laser offers an alternative technique for uncovering dental implants. This article presents two cases in which four dental implants were uncovered using a soft tissue laser. This technique provides an efficient and patient-friendly method to perform second-stage implant surgery, safely allowing a faster rehabilitative phase. PMID:16366049

  9. Diode-pumped self-frequency-doubled neodymium yttrium aluminum borate (NYAB) laser

    NASA Technical Reports Server (NTRS)

    Hemmati, Hamid

    1992-01-01

    Over 50 mW of the fundamental-mode 531-nm laser output was obtained with approximately 4 percent optical-to-optical conversion efficiency from a self-frequency-doubling NYAB crystal when pumped with two 1-W diode lasers. The prospect of higher conversion efficiency is discussed.

  10. Mercury and Beyond: Diode-Pumped Solid-State Lasers for Inertial Fusion Energy

    SciTech Connect

    Bibeau, C.; Beach, R.J.; Bayramian, A.; Chanteloup, J.C.; Ebbers, C.A.; Emanuel, M.A.; Orth, C.D.; Rothenberg, J.E.; Schaffers, K.I.; Skidmore, J.A.; Sutton, S.B.; Zapata, L.E.; Payne, S.A.; Powell, H.T.

    1999-10-19

    We have begun building the ''Mercury'' laser system as the first in a series of new generation diode-pumped solid-state lasers for inertial fusion research. Mercury will integrate three key technologies: diodes, crystals, and gas cooling, within a unique laser architecture that is scalable to kilojoule energy levels for fusion energy applications. The primary performance goals include 10% electrical efficiencies at 10 Hz and 100 J with a 2-10 ns pulse length at 1.047 pm wavelength. When completed, Mercury will allow rep-rated target experiments with multiple target chambers for high energy density physics research.

  11. Cooling of cesium atomic beam with light from spectrally broadened diode lasers

    NASA Astrophysics Data System (ADS)

    Chan, Yat; Bhaskar, Natarajan D.

    1995-12-01

    We have used spectrally broadened counterpropagating radiation from tunable diode lasers to cool an atomic beam of cesium. This produces a continuous beam of cold atoms. The injection current to the single-mode diode laser is modulated at 10 MHz, resulting in spectrally broadened light for atomic cooling and optical pumping. The atomic beam is probed with a weak single-mode laser. This is a simple and relatively inexpensive method for producing a continuous supply of cold atoms. Copyright (c) 1995 Optical Society of America

  12. Improving Reliability of High Power Quasi-CW Laser Diode Arrays Operating in Long Pulse Mode

    NASA Technical Reports Server (NTRS)

    Amzajerdian, Farzin; Meadows, Byron L.; Barnes, Bruce W.; Lockard, George E.; Singh, Upendra N.; Kavaya, Michael J.; Baker, Nathaniel R.

    2006-01-01

    Operating high power laser diode arrays in long pulse regime of about 1 msec, which is required for pumping 2-micron thulium and holmium-based lasers, greatly limits their useful lifetime. This paper describes performance of laser diode arrays operating in long pulse mode and presents experimental data of the active region temperature and pulse-to-pulse thermal cycling that are the primary cause of their premature failure and rapid degradation. This paper will then offer a viable approach for determining the optimum design and operational parameters leading to the maximum attainable lifetime.

  13. Bistable optical devices with laser diodes coupled to absorbers of narrow spectral bandwidth.

    PubMed

    Maeda, Y

    1994-06-20

    An optical signal inverter was demonstrated with a combination of the following two effects: One is the decrease of the transmission of an Er-doped YAG crystal with increasing red shift of a laser diode resulting from an increase in the injection current, and the other is a negative nonlinear absorption in which the transmission decreases inversely with increasing laser intensity. Because a hysteresis characteristic exists in the relationship between the wavelength and the injection current of the laser diode, an optical bistability was observed in this system. PMID:20935754

  14. Negative-T{sub 0} InGaN laser diodes and their degradation

    SciTech Connect

    Bojarska, Agata; Suski, Tadeusz

    2015-04-27

    We studied the InGaN laser diode, emitting in the blue region of the spectrum and characterized by a negative characteristic temperature T{sub 0}. The corresponding decrease in the threshold current with the increase in temperature for this device is caused by the increased distance between the electron-blocking layer and the quantum wells. Because of the non-monotonic temperature dependence of laser parameters, we can demonstrate a correlation of the degradation rate with nonradiative part of the total device current. This result indicates the potential importance of the recombination processes occurring outside of the active region for the reliability of InGaN laser diodes.

  15. Wavelength tunable, 264 J laser diode array for 10 Hz/1ms Yb:YAG pumping

    NASA Astrophysics Data System (ADS)

    Chanteloup, J.-C.; Albach, D.; Assémat, F.; Bahbah, S.; Bourdet, G.; Piatti, P.; Pluvinage, M.; Vincent, B.; LeTouzé, G.; Mattern, T.; Biesenbach, J.; Müntz, H.; Noeske, A.; Venohr, R.

    2008-05-01

    The Lucia [1,2] Laser program, under development at the LULI laboratory, aims at delivering a 1030 nm, 100J, 10 Hz, 10 ns pulse train. The two laser heads used in the amplification stage relies on water-cooled mm-thick Yb:YAG disks, each of them pumped by a 34×13 cm2 Laser Diode Array (LDA). For each LDA, the 88 QCW diodes stacks manufactured by DILAS GmbH will be tiled in an 8×11 arrangement. Fine wavelength tuning is performed through bias current adjustment, water temperature control and conductivity adjustment. Wavelength homogeneity experimental verification has been validated.

  16. Open-path atmospheric transmission for a diode-pumped cesium laser.

    PubMed

    Rice, Christopher A; Lott, Gordon E; Perram, Glen P

    2012-12-01

    A tunable diode laser absorption spectroscopy device was developed to study atmospheric propagation for emerging high-energy laser weapons. The cesium diode-pumped alkali laser operates near 895 nm in the vicinity of several water-vapor absorption lines. Temperature, pressure, and water vapor concentration were determined for 150 m and 1 km open paths with statistical errors of ∼0.2%. Comparison with meteorological instruments yields agreement for the 1 km path to within 0.6% for temperature, 3.7% for pressure, and 2.4% for concentration. PMID:23207380

  17. Monitoring Temperature in High Enthalpy Arc-heated Plasma Flows using Tunable Diode Laser Absorption Spectroscopy

    NASA Technical Reports Server (NTRS)

    Martin, Marcel Nations; Chang, Leyen S.; Jeffries, Jay B.; Hanson, Ronald K.; Nawaz, Anuscheh; Taunk, Jaswinder S.; Driver, David M.; Raiche, George

    2013-01-01

    A tunable diode laser sensor was designed for in situ monitoring of temperature in the arc heater of the NASA Ames IHF arcjet facility (60 MW). An external cavity diode laser was used to generate light at 777.2 nm and laser absorption used to monitor the population of electronically excited oxygen atoms in an air plasma flow. Under the assumption of thermochemical equilibrium, time-resolved temperature measurements were obtained on four lines-of-sight, which enabled evaluation of the temperature uniformity in the plasma column for different arcjet operating conditions.

  18. Selective isotope determination of lanthanum by diode-laser-initiated resonance-ionization mass spectrometry

    NASA Astrophysics Data System (ADS)

    Young, J. P.; Shaw, R. W.

    1995-08-01

    A diode-laser step has been incorporated into a resonance-ionization mass spectrometry optical excitation process to enhance the isotopic selectivity of the technique. Lanthanum isotope ratio enhancements as high as 103 were achieved by use of a single-frequency cw diode laser tuned to excite the first step of a three-step excitation-ionization optical process; the subsequent steps were excited by use of a pulsed dye laser. Applying the same optical technique, we measured atomic hyperfine constants for the high-lying even-parity 4D5/2 state of lanthanum at 30354 cm-1 . The general utility of this spectral approach is discussed.

  19. All-fiber based amplification of 40 ps pulses from a gain-switched laser diode.

    PubMed

    Kanzelmeyer, Sebastian; Sayinc, Hakan; Theeg, Thomas; Frede, Maik; Neumann, Joerg; Kracht, Dietmar

    2011-01-31

    Amplification of a gain-switched laser diode is demonstrated in an all-fiber based setup. The amplified spontaneous emission between two consecutive pulses was investigated quantitatively in the time domain. A maximum pulse energy of 13 µJ at a repetition rate of 1 MHz and a pulse duration of 40 ps was extracted, corresponding to a peak power of 270 KW. To the best of our knowledge, this is the highest extracted pulse energy from a laser system seeded by a gain-switched laser diode. Temporal pulse deformation due to intrapulse Raman scattering was observed in the reported system. PMID:21369000

  20. Tunable diode-laser heterodyne spectrometer for remote observations near 8 microns

    NASA Technical Reports Server (NTRS)

    Glenar, D.; Kostiuk, T.; Jennings, D. E.; Buhl, D.; Mumma, M. J.

    1982-01-01

    A diode-laser-based, ultrahigh resolution IR heterodyne spectrometer for laboratory and field use has been developed for operation between 7.5 and 8.5 microns. The local oscillator is a PbSe tunable diode laser kept continuously at operating temperatures of 12-60 K using a closed-cycle cooler. The laser output frequency is controlled and stabilized using a high-precision diode current supply, constant temperature controller, and a shock isolator mounted between the refrigerator cold tip and the diode mount. The system largely employs reflecting optics to minimize losses from internal reflection and absorption and to eliminate chromatic effects. Spectral analysis of the diode-laser output between 0 and 1 GHz reveals excess noise at many diode current settings, which limits the IR spectral regions over which useful heterodyne operation can be achieved. Observations have been made of atmospheric N2O, O3, and CH4 between 1170 and 1200/cm, using both a single-frequency swept IF channel and a 64-channel RF spectral line receiver with a total IF coverage of 1600 MHz.