[Comparison of chemical components of essential oils in needles of Pinus massoniana Lamb and Pinus elliottottii Engelm from Guangxi].

PubMed

Shen, Changmao; Duan, Wengui; Cen, Bo; Tan, Jianhui

2006-11-01

Essential oils were extracted by steam distillation from the needles of Pinus massoniana Lamb and Pinus elliottottii Engelm grown in Guangxi. Various factors such as pine needle dosage and extraction time which may influence the oil yield were investigated. The optimum conditions were found to be as follows: pine needle dosage 700 g, extraction time 5 h. The essential oil yields from the needles of Pinus massoniana Lamb and Pinus elliottottii Engelm were 0.45% and 0.19%, respectively. Moreover, the chemical compositions of the essential oils were analyzed by gas chromatography (GC) and gas chromatography-mass spectrometry (GC-MS). Sixty four components in the essential oil from needle of Pinus massoniana Lamb were separated and twenty of them (98.59%) were identified while seventy three components in the essential oil from needle of Pinus elliottottii Engelm were separated and twenty nine of them (94.23%) were identified. Generally, the compositions of the essential oils from needles of the two varieties were similar but the contents of some compounds differed greatly. Especially, the content of alpha-pinene in the essential oils from Pinus massoniana Lamb needles was 2.6 times as that from Pinus elliottottii Engelm needles, but the content of beta-pinene was less than the latter. Mono- and sesquiterpenes were the main composition of the essential oils from Pinus massoniana Lamb and Pinus elliottottii Engelm needles.

Comparative mapping in Pinus: sugar pine (Pinus lambertiana Dougl.) and loblolly pine (Pinus taeda L.).Tree Genet Genomes 7:457-468

Treesearch

Kathleen D. Jermstad; Andrew J. Eckert; Jill L. Wegrzyn; Annette Delfino-Mix; Dean A Davis; Deems C. Burton; David B. Neale

2011-01-01

The majority of genomic research in conifers has been conducted in the Pinus subgenus Pinus mostly due to the high economic importance of the species within this taxon. Genetic maps have been constructed for several of these pines and comparative mapping analyses have consistently revealed notable synteny. In contrast,...

Fundamental studies on a novel die concept for round-point shear-clinching

NASA Astrophysics Data System (ADS)

Hörhold, Réjane; Müller, Martin; Merklein, Marion; Meschut, Gerson

2016-10-01

A newly-developed round-point shear-clinching technology could increase the use of different materials like well formable aluminium and hardly formable ultra-high-strength steels (UHSS). This innovative technology joins in a single-stage process without any pilot-hole, surface pre-treatment or auxiliary joining part. The combination of an inner and outer punch realises an indirect cutting operation of the die-sided material, whereas the punch-sided material remains unharmed. The current die-sided tool set acts as a cutting die and enables a radial extrusion of the punch-sided material after being drawn though the created hole in the UHSS. The die has a fixed die depth. After ejecting the joined components, the slug has to be removed from the top of the spring-loaded anvil. The novel die concept investigated in this paper offers the possibility to push the slug continuously through the die in the joining direction. The removed slugs remain inside the die, so manual removal is unnecessary. The one-parted tool is supposed to be more robust than the multi-parted one that is currently used. This paper represents the task to evaluate the geometry of a useful shear-clinching die concept. To reduce the experimental effort, FEM should assist the development of the most promising approach. To quantify the success, conventional shear-clinching with opening die acts as a reference. The results show the high potential and the raison d'être of shear-clinching technologies as a mechanical joining technology for future multimaterial applications especially for UHSS.

Height growth determinants in pines: A case study of Pinus contorta and Pinus monticola

Treesearch

Isabelle Chuine; Gerald E. Rehfeldt; Sally N. Aitken

2006-01-01

In this study we aimed to compare and explain the height growth performance of two contrasting pine species: lodgepole pine (Pinus contorta Dougl. ex. Loud) and western white pine (Pinus monticola Dougl. ex D. Don.). We compiled measurements of total height growth at different ages and shoot elongation phenology realized in several...

Using among-year variation to assess maternal effects in Pinus aristata and Pinus flexilis

Treesearch

Erin M. Borgman; Anna W. Schoettle; Amy L. Angert

2014-01-01

Maternal effects, the effect of the maternal environment during development on offspring growth, can complicate the interpretation of common garden studies. Growing one or more generations in a common environment can help minimize maternal effects, but is often not practical with long-lived species. In Pinus aristata Engelm. and Pinus flexilis James, we assessed...

Natural loblolly and shortleaf pine productivity through 53 years of management under four reproduction cutting methods

Treesearch

Michael D. Cain; Michael G. Shelton

2001-01-01

A study was initiated in 1943 to evaluate the long-term productivity of loblolly (Pinus taeda L.) and shortleaf pines (P. echinata Mill.) when managed under four reproduction cutting methods—clearcut, heavy seedtree, diameter-limit, and selection—on the Upper Coastal Plain of southeastern Arkansas. Early volume production...

Forest mortality in high-elevation whitebark pine (Pinus albicaulis) forests of eastern California, USA; influence of environmental context, bark beetles, climatic water deficit, and warming

Treesearch

Constance I. Millar; Robert D. Westfall; Diane L. Delany; Matthew J. Bokach; Alan L. Flint; Lorraine E. Flint

2012-01-01

Whitebark pine (Pinus albicaulis Engelm.) in subalpine zones of eastern California experienced significant mortality from 2007 to 2010. Dying stands were dense (mean basal area 47.5 m2/ha), young (mean 176 years), and even-age; mean stand mortality was 70%. Stands were at low elevations (mean 2993 m), on northerly aspects, and...

Performance of Slash Pine Bare-Root Seedlings and Containerized Rooted Cuttings Planted on Five Dates in Louisiana

Treesearch

Alper Akgul; Michael G. Messina; Alan Wilson; Joe Weber

2004-01-01

Landowners are interested in extending the normal planting season, as well as the comparative field performance, of nursery bare-root seedlings and containerized rooted cuttings. The effect of seasonal planting dates on field performance of two stock types of slash pine (Pinus elliottii Engelm.) was examined. Slash pine bare-root seedlings (BRS) and...

Regional vegetation die-off in response to global-change-type drought

USGS Publications Warehouse

Breshears, D.D.; Cobb, N.S.; Rich, P.M.; Price, K.P.; Allen, Craig D.; Balice, R.G.; Romme, W.H.; Kastens, J.H.; Floyd, M. Lisa; Belnap, J.; Anderson, J.J.; Myers, O.B.; Meyer, Clifton W.

2005-01-01

Future drought is projected to occur under warmer temperature conditions as climate change progresses, referred to here as global-change-type drought, yet quantitative assessments of the triggers and potential extent of drought-induced vegetation die-off remain pivotal uncertainties in assessing climate-change impacts. Of particular concern is regional-scale mortality of overstory trees, which rapidly alters ecosystem type, associated ecosystem properties, and land surface conditions for decades. Here, we quantify regional-scale vegetation die-off across southwestern North American woodlands in 2002-2003 in response to drought and associated bark beetle infestations. At an intensively studied site within the region, we quantified that after 15 months of depleted soil water content, >90% of the dominant, overstory tree species (Pinus edulis, a piñon) died. The die-off was reflected in changes in a remotely sensed index of vegetation greenness (Normalized Difference Vegetation Index), not only at the intensively studied site but also across the region, extending over 12,000 km2 or more; aerial and field surveys confirmed the general extent of the die-off. Notably, the recent drought was warmer than the previous subcontinental drought of the 1950s. The limited, available observations suggest that die-off from the recent drought was more extensive than that from the previous drought, extending into wetter sites within the tree species' distribution. Our results quantify a trigger leading to rapid, drought-induced die-off of overstory woody plants at subcontinental scale and highlight the potential for such die-off to be more severe and extensive for future global-change-type drought under warmer conditions.

Regional vegetation die-off in response to global-change-type drought

PubMed Central

Breshears, David D.; Cobb, Neil S.; Rich, Paul M.; Price, Kevin P.; Allen, Craig D.; Balice, Randy G.; Romme, William H.; Kastens, Jude H.; Floyd, M. Lisa; Belnap, Jayne; Anderson, Jesse J.; Myers, Orrin B.; Meyer, Clifton W.

2005-01-01

Future drought is projected to occur under warmer temperature conditions as climate change progresses, referred to here as global-change-type drought, yet quantitative assessments of the triggers and potential extent of drought-induced vegetation die-off remain pivotal uncertainties in assessing climate-change impacts. Of particular concern is regional-scale mortality of overstory trees, which rapidly alters ecosystem type, associated ecosystem properties, and land surface conditions for decades. Here, we quantify regional-scale vegetation die-off across southwestern North American woodlands in 2002-2003 in response to drought and associated bark beetle infestations. At an intensively studied site within the region, we quantified that after 15 months of depleted soil water content, >90% of the dominant, overstory tree species (Pinus edulis, a piñon) died. The die-off was reflected in changes in a remotely sensed index of vegetation greenness (Normalized Difference Vegetation Index), not only at the intensively studied site but also across the region, extending over 12,000 km2 or more; aerial and field surveys confirmed the general extent of the die-off. Notably, the recent drought was warmer than the previous subcontinental drought of the 1950s. The limited, available observations suggest that die-off from the recent drought was more extensive than that from the previous drought, extending into wetter sites within the tree species' distribution. Our results quantify a trigger leading to rapid, drought-induced die-off of overstory woody plants at subcontinental scale and highlight the potential for such die-off to be more severe and extensive for future global-change-type drought under warmer conditions. PMID:16217022

Mineral Analysis of Pine Nuts (Pinus spp.) Grown in New Zealand

PubMed Central

Vanhanen, Leo P.; Savage, Geoffrey P.

2013-01-01

Mineral analysis of seven Pinus species grown in different regions of New Zealand; Armand pine (Pinus armandii Franch), Swiss stone pine (Pinus cembra L.), Mexican pinyon (Pinus cembroides Zucc. var. bicolor Little), Coulter pine (Pinus coulteri D. Don), Johann’s pine (Pinus johannis M.F. Robert), Italian stone pine (Pinus pinea L.) and Torrey pine (Pinus torreyana Parry ex Carrière), was carried out using an inductively coupled plasma optical emission spectrophotometer (ICP-OES) analysis. Fourteen different minerals (Al, B, Ca, Cr, Cu, Fe, K, Mg, Mn, Na, Ni, P, S and Zn) were identified in all seven varieties, except that no Al or Na was found in Pinus coulteri D. Don. New Zealand grown pine nuts are a good source of Cu, Mg, Mn, P and Zn, meeting or exceeding the recommended RDI for these minerals (based on an intake of 50 g nuts/day) while they supplied between 39%–89% of the New Zealand RDI for Fe. Compared to other commonly eaten tree-nuts New Zealand grown pine nuts are an excellent source of essential minerals. PMID:28239104

Mineral Analysis of Pine Nuts (Pinus spp.) Grown in New Zealand.

PubMed

Vanhanen, Leo P; Savage, Geoffrey P

2013-04-03

Mineral analysis of seven Pinus species grown in different regions of New Zealand; Armand pine ( Pinus armandii Franch), Swiss stone pine ( Pinus cembra L.), Mexican pinyon ( Pinus cembroides Zucc. var. bicolor Little), Coulter pine ( Pinus coulteri D. Don), Johann's pine ( Pinus johannis M.F. Robert), Italian stone pine ( Pinus pinea L.) and Torrey pine ( Pinus torreyana Parry ex Carrière), was carried out using an inductively coupled plasma optical emission spectrophotometer (ICP-OES) analysis. Fourteen different minerals (Al, B, Ca, Cr, Cu, Fe, K, Mg, Mn, Na, Ni, P, S and Zn) were identified in all seven varieties, except that no Al or Na was found in Pinus coulteri D. Don. New Zealand grown pine nuts are a good source of Cu, Mg, Mn, P and Zn, meeting or exceeding the recommended RDI for these minerals (based on an intake of 50 g nuts/day) while they supplied between 39%-89% of the New Zealand RDI for Fe. Compared to other commonly eaten tree-nuts New Zealand grown pine nuts are an excellent source of essential minerals.

Chloroplast DNA Diversity among Trees, Populations and Species in the California Closed-Cone Pines (Pinus Radiata, Pinus Muricata and Pinus Attenuata)

PubMed Central

Hong, Y. P.; Hipkins, V. D.; Strauss, S. H.

1993-01-01

The amount, distribution and mutational nature of chloroplast DNA polymorphisms were studied via analysis of restriction fragment length polymorphisms in three closely related species of conifers, the California closed-cone pines-knobcone pine: Pinus attenuata Lemm.; bishop pine: Pinus muricata D. Don; and Monterey pine: Pinus radiata D. Don. Genomic DNA from 384 trees representing 19 populations were digested with 9-20 restriction enzymes and probed with cloned cpDNA fragments from Douglas-fir [Pseudotsuga menziesii (Mirb.) Franco] that comprise 82% of the chloroplast genome. Up to 313 restriction sites were surveyed, and 25 of these were observed to be polymorphic among or within species. Differences among species accounted for the majority of genetic (haplotypic) diversity observed [G(st) = 84(+/-13)%]; nucleotide diversity among species was estimated to be 0.3(+/-0.1)%. Knobcone pine and Monterey pine displayed almost no genetic variation within or among populations. Bishop pine also showed little variability within populations, but did display strong population differences [G(st) = 87(+/-8)%] that were a result of three distinct geographic groups. Mean nucleotide diversity within populations was 0.003(+/-0.002)%; intrapopulation polymorphisms were found in only five populations. This pattern of genetic variation contrasts strongly with findings from study of nuclear genes (allozymes) in the group, where most genetic diversity resides within populations rather than among populations or species. Regions of the genome subject to frequent length mutations were identified; estimates of subdivision based on length variant frequencies in one region differed strikingly from those based on site mutations or allozymes. Two trees were identified with a major chloroplast DNA inversion that closely resembled one documented between Pinus and Pseudotsuga. PMID:7905846

Volatile constituents of Pinus roxburghii from Nepal.

PubMed

Satyal, Prabodh; Paudel, Prajwal; Raut, Josna; Deo, Akash; Dosoky, Noura S; Setzer, William N

2013-01-01

Pinus roxburghii Sarg. Is one of 3 species of pine found in Nepal, the oil of which is traditionally used to treat cuts, wounds, boils, and blisters. To obtain, analyze, and examine the anti-microbial and cytotoxic activities of the essential oils of P. roxburghii. Three plant parts (cone, needle, and bark) of Pinus roxburghii were collected in Biratnagar, Nepal. The essential oils were obtained by hydrodistillation, and the chemical compositions were determined by GC-MS. The needle and cone essential oils were screened for anti-microbial activity against Bacillus cereus, Staphylococcus aureus, Pseudomonas aeruginosa, Escherichia coli, and Aspergillus niger; brine shrimp (Artemia salina) lethality; and in-vitro cytotoxicity against MCF-7 cells. GC-MS analysis for the cone oil revealed 81 compounds with 78 components being identified (95.5% of the oil) while 98.3% of needle oil was identified to contain 68 components and 98.6% of the bark oil (38 components) was identified. The 3 essential oils were dominated by sesquiterpenes, particularly (E)-caryophyllene (26.8%-34.5%) and α-humulene (5.0%-7.3%) as well as monoterpene alcohols terpinen-4-ol (4.1%-30.1%) and α-terpineol(2.8%-5.0%). The monoterpene δ-3-carene was present only in needle and cone essential oils (2.3% and 6.8%, respectively). Bio-activity assays of the cone essential oil of P. roxburghii showed remarkable cytotoxic activity (100% killing of MCF-7 cells at 100 μg/mL) along with notable brine shrimp lethality (LC50 =11.8 μg/mL). The cone essential oil did not show anti-bacterial activity, but it did exhibit anti-fungal activity against Aspergillus niger (MIC=39 μg/mL). The bioactivity of P. roxburghii essential oil is consistent with its traditional medicinal use.

Volatile constituents of Pinus roxburghii from Nepal

PubMed Central

Satyal, Prabodh; Paudel, Prajwal; Raut, Josna; Deo, Akash; Dosoky, Noura S.; Setzer, William N.

2013-01-01

Background: Pinus roxburghii Sarg. Is one of 3 species of pine found in Nepal, the oil of which is traditionally used to treat cuts, wounds, boils, and blisters. Objective: To obtain, analyze, and examine the anti-microbial and cytotoxic activities of the essential oils of P. roxburghii. Materials and Methods: Three plant parts (cone, needle, and bark) of Pinus roxburghii were collected in Biratnagar, Nepal. The essential oils were obtained by hydrodistillation, and the chemical compositions were determined by GC-MS. The needle and cone essential oils were screened for anti-microbial activity against Bacillus cereus, Staphylococcus aureus, Pseudomonas aeruginosa, Escherichia coli, and Aspergillus niger; brine shrimp (Artemia salina) lethality; and in-vitro cytotoxicity against MCF-7 cells. Results: GC-MS analysis for the cone oil revealed 81 compounds with 78 components being identified (95.5% of the oil) while 98.3% of needle oil was identified to contain 68 components and 98.6% of the bark oil (38 components) was identified. The 3 essential oils were dominated by sesquiterpenes, particularly (E)-caryophyllene (26.8%-34.5%) and α-humulene (5.0%-7.3%) as well as monoterpene alcohols terpinen-4-ol (4.1%-30.1%) and α-terpineol(2.8%-5.0%). The monoterpene δ-3-carene was present only in needle and cone essential oils (2.3% and 6.8%, respectively). Bio-activity assays of the cone essential oil of P. roxburghii showed remarkable cytotoxic activity (100% killing of MCF-7 cells at 100 μg/mL) along with notable brine shrimp lethality (LC50 =11.8 μg/mL). The cone essential oil did not show anti-bacterial activity, but it did exhibit anti-fungal activity against Aspergillus niger (MIC=39 μg/mL). Conclusion: The bioactivity of P. roxburghii essential oil is consistent with its traditional medicinal use. PMID:23598924

Effects of reproduction cutting method and hardwood retention on shortleaf pine seed production in natural stands of the Ouachita Mountains

Treesearch

Robert F. Wittwer; Micahel G. Shelton; James M. Guldin

2003-01-01

Shortleaf pine (Pinus echinata Mill.) seed production was monitored for 4 yr in stands harvested by a range of even- and uneven-aged reproduction cutting methods. The fifty-two 35–40 ac stands were distributed throughout the Ouachita Mountains from central Arkansas to eastern Oklahoma. Seed crops were characterized as good, poor, poor, and bumper,...

Shrub-Steppe Early Succession Following Juniper Cutting and Prescribed Fire

NASA Astrophysics Data System (ADS)

Bates, Jonathan D.; Davies, Kirk W.; Sharp, Robert N.

2011-03-01

Pinus- Juniperus L. (Piñon-juniper) woodlands of the western United States have expanded in area nearly 10-fold since the late 1800's. Juniperus occidentalis ssp. occidentalis Hook. (western juniper) dominance in sagebrush steppe has several negative consequences, including reductions in herbaceous production and diversity, decreased wildlife habitat, and higher erosion and runoff potentials. Prescribed fire and mechanical tree removal are the main methods used to control J. occidentalis and restore sagebrush steppe. However, mature woodlands become difficult to prescribe burn because of the lack of understory fuels. We evaluated partial cutting of the woodlands (cutting 25-50% of the trees) to increase surface fuels, followed by prescribed fire treatments in late successional J. occidentalis woodlands of southwest Idaho to assess understory recovery. The study was conducted in two different plant associations and evaluated what percentage of the woodland required preparatory cutting to eliminate remaining J. occidentalis by prescribed fire, determined the impacts of fire to understory species, and examined early post-fire successional dynamics. The study demonstrated that late successional J. occidentalis woodlands can be burned after pre-cutting only a portion of the trees. Early succession in the cut-and-burn treatments were dominated by native annual and perennial forbs, in part due to high mortality of perennial bunchgrasses. By the third year after fire the number of establishing perennial grass seedlings indicated that both associations would achieve full herbaceous recovery. Cutting-prescribed fire combinations are an effective means for controlling encroaching late successional J. occidentalis and restoring herbaceous plant communities. However, land managers should recognize that there are potential problems associated with cutting-prescribed fire applications when invasive weeds are present.

Shrub-steppe early succession following juniper cutting and prescribed fire.

PubMed

Bates, Jonathan D; Davies, Kirk W; Sharp, Robert N

2011-03-01

Pinus-Juniperus L. (Piñon-juniper) woodlands of the western United States have expanded in area nearly 10-fold since the late 1800's. Juniperus occidentalis ssp. occidentalis Hook. (western juniper) dominance in sagebrush steppe has several negative consequences, including reductions in herbaceous production and diversity, decreased wildlife habitat, and higher erosion and runoff potentials. Prescribed fire and mechanical tree removal are the main methods used to control J. occidentalis and restore sagebrush steppe. However, mature woodlands become difficult to prescribe burn because of the lack of understory fuels. We evaluated partial cutting of the woodlands (cutting 25-50% of the trees) to increase surface fuels, followed by prescribed fire treatments in late successional J. occidentalis woodlands of southwest Idaho to assess understory recovery. The study was conducted in two different plant associations and evaluated what percentage of the woodland required preparatory cutting to eliminate remaining J. occidentalis by prescribed fire, determined the impacts of fire to understory species, and examined early post-fire successional dynamics. The study demonstrated that late successional J. occidentalis woodlands can be burned after pre-cutting only a portion of the trees. Early succession in the cut-and-burn treatments were dominated by native annual and perennial forbs, in part due to high mortality of perennial bunchgrasses. By the third year after fire the number of establishing perennial grass seedlings indicated that both associations would achieve full herbaceous recovery. Cutting-prescribed fire combinations are an effective means for controlling encroaching late successional J. occidentalis and restoring herbaceous plant communities. However, land managers should recognize that there are potential problems associated with cutting-prescribed fire applications when invasive weeds are present.

Regeneration of Rocky Mountain bristlecone pine (Pinus aristata) and limber pine (Pinus flexilis) three decades after stand-replacing fires

Treesearch

Jonathan D. Coop; Anna W. Schoettle

2009-01-01

Rocky Mountain bristlecone pine (Pinus aristata) and limber pine (Pinus flexilis) are important highelevation pines of the southern Rockies that are forecast to decline due to the recent spread of white pine blister rust (Cronartium ribicola) into this region. Proactive management strategies to promote the evolution of rust resistance and maintain ecosystem function...

Fatty acids of Pinus elliottii tissues.

NASA Technical Reports Server (NTRS)

Laseter, J. L.; Lawler, G. C.; Walkinshaw, C. H.; Weete, J. D.

1973-01-01

The total fatty constituents of slash pine (Pinus elliottii) tissue cultures, seeds, and seedlings were examined by GLC and MS. Qualitatively, the fatty acid composition of these tissues was found to be very similar to that reported for other pine species. The fatty acid contents of the tissue cultures resembled that of the seedling tissues. The branched-chain C(sub 17) acid reported for several other Pinus species was confirmed as the anteiso isomer.

Bio-engineering traits of Pinus radiata D.Don

NASA Astrophysics Data System (ADS)

Giadrossich, Filippo; Marden, Michael; Marrosu, Roberto; Schwarz, Massimiliano; Phillips, Chris John; Cohen, Denis; Niedda, Marcello

2017-04-01

Pinus radiata is widely cultivated in New Zealand. Due to steep slopes and intense rainfall, the silviculture of Pinus radiata forests is important to control erosion and slope stability. Bio-engineering traits such as root distribution and root tensile strength are fundamental to understand the effectiveness of Pinus radiata. This information is needed to use the state of the art root reinforcement model (the Root Bundle Model) and the physically-based slope stability model SOSlope. Yet, little is known about root distribution and tensile strength for this specie. We measured soil moisture and carried out 30 field tensile tests on roots of Pinus radiata. We also measured root distribution data from 5 plants, digging arc of circles 0.6 radian around the trees in four opposite directions. We fully excavated the root system of two trees. Using the Root Bundle Model, results of our measurements allow estimation of root reinforcement. With the slope stability model SOSlope, information on the intensity and frequency of harvesting and on the development of weak zones that can be supported by a stand of Pinus radiata in relation to slope stability can be calculated. An added value is that the collected data allow us to make inferences between number and sizes of roots, and growth direction.

Reference karyotype and cytomolecular map for loblolly pine (Pinus taeda L.)

Treesearch

M. Nurul Islam-faridi; C. Dana Nelson; Thomas L. Kubisiak

2007-01-01

A reference karyotype is presented for loblolly pine (Pinus taeda L., subgenus Pinus , section Pinus, subsection Australes), based on fluorescent in situ hybridization (FISH), using 18s-28s rDNA, 5s rDNA, and Arabidopsis-type telomere repeat sequence (A-type TRS). Well...

Using silvicultural practices to regulate competition, resource availability, and growing conditions for Pinus palustris seedlings underplanted in Pinus taeda forests

Treesearch

Benjamin O. Knapp; G. Geoff Wang; Joan L. Walker; Huifeng Hu

2016-01-01

In the southeastern United States, many forest managers are interested in restoring longleaf pine (Pinus palustris Mill.) to upland sites that currently support loblolly pine (Pinus taeda L.). We quantified the effects of four canopy treatments (uncut Control; MedBA, harvest to 9 m2·ha−1...

Late Eocene white pines (Pinus subgenus Strobus) from southern China.

PubMed

Xu, Qingqing; Zhou, Wenjun; Kodrul, Tatiana M; Naugolnykh, Serge V; Jin, Jianhua

2015-11-09

Fossil records indicate that the genus Pinus L. split into two subgenera by the Late Cretaceous, although subgenus Strobus (D. Don) Lemmon is less well documented than subgenus Pinus L., especially in eastern Asia. In this paper, Pinus maomingensis sp. nov. is established based on a compressed seed cone from the upper Eocene of the Maoming Basin of southern China. This species is attributed to genus Pinus, subgenus Strobus, section Quinquefoliae Duhamel, subsection Strobus Loudon based on the combination of morphological characters obtained from the cone scales, specifically from the terminal umbo, rhombic apophysis, and cuticle structure. Associated fascicles of needle leaves with deciduous sheaths and bulbous bases are recognized as Pinus sp. and also represent Pinus subgenus Strobus. This new discovery from the Maoming Basin constitutes the first megafossil record of subgenus Strobus from southern China and implies that the members of this subgenus arrived in the southern region of China by the late Eocene. The extant species of subgenus Strobus are mainly distributed in northern temperate and tropical to subtropical mountainous regions. We propose that the Maoming Basin was adjacent to a mountainous region during the late Eocene.

Late Eocene white pines (Pinus subgenus Strobus) from southern China

PubMed Central

Xu, Qingqing; Zhou, Wenjun; Kodrul, Tatiana M.; Naugolnykh, Serge V.; Jin, Jianhua

2015-01-01

Fossil records indicate that the genus Pinus L. split into two subgenera by the Late Cretaceous, although subgenus Strobus (D. Don) Lemmon is less well documented than subgenus Pinus L., especially in eastern Asia. In this paper, Pinus maomingensis sp. nov. is established based on a compressed seed cone from the upper Eocene of the Maoming Basin of southern China. This species is attributed to genus Pinus, subgenus Strobus, section Quinquefoliae Duhamel, subsection Strobus Loudon based on the combination of morphological characters obtained from the cone scales, specifically from the terminal umbo, rhombic apophysis, and cuticle structure. Associated fascicles of needle leaves with deciduous sheaths and bulbous bases are recognized as Pinus sp. and also represent Pinus subgenus Strobus. This new discovery from the Maoming Basin constitutes the first megafossil record of subgenus Strobus from southern China and implies that the members of this subgenus arrived in the southern region of China by the late Eocene. The extant species of subgenus Strobus are mainly distributed in northern temperate and tropical to subtropical mountainous regions. We propose that the Maoming Basin was adjacent to a mountainous region during the late Eocene. PMID:26548658

Evaluating the role of cutting treatments, fire and soil seed banks in an experimental framework in ponderosa pine forests of the Black Hills, South Dakota

Treesearch

Cody L. Wienk; Carolyn Hull Sieg; Guy R. McPherson

2004-01-01

Pinus ponderosa Laws. (ponderosa pine) forests have changed considerably during the past century, partly because recurrent fires have been absent for a century or more. A number of studies have explored the influence of timber harvest or burning on understory production in ponderosa pine forests, but study designs incorporating cutting and prescribed...

Precipitation thresholds and drought-induced tree die-off: Insights from patterns of Pinus edulis mortality along an environmental stress gradient

Treesearch

Michael J. Clifford; Patrick D. Royer; Neil S. Cobb; David D. Breshears; Paulette L. Ford

2013-01-01

Recent regional tree die-off events appear to have been triggered by a combination of drought and heat - referred to as 'global-change-type drought'. To complement experiments focused on resolving mechanisms of drought-induced tree mortality, an evaluation of how patterns of tree die-off relate to highly spatially variable precipitation is needed....

[Vertical distribution of fuels in Pinus yunnanensis forest and related affecting factors].

PubMed

Wang, San; Niu, Shu-Kui; Li, De; Wang, Jing-Hua; Chen, Feng; Sun, Wu

2013-02-01

In order to understand the effects of fuel loadings spatial distribution on forest fire kinds and behaviors, the canopy fuels and floor fuels of Pinus yunnanensis forests with different canopy density, diameter at breast height (DBH), tree height, and stand age and at different altitude, slope grade, position, and aspect in Southwest China were taken as test objects, with the fuel loadings and their spatial distribution characteristics at different vertical layers compared and the fire behaviors in different stands analyzed. The relationships between the fuel loadings and the environmental factors were also analyzed by canonical correspondence analysis (CCA). In different stands, there existed significant differences in the vertical distribution of fuels. Pinus yunnanensis-Qak-Syzygium aromaticum, Pinus yunnanensis-oak, and Pinus yunnanensis forests were likely to occur floor fire but not crown fire, while Pinus yunnanensis-Platycladus orientalis, Pinus yunnanensis-Keteleeria fortune, and Keteleeria fortune-Pinus yunnanensis were not only inclined to occur floor fire, but also, the floor fire could be easily transformed into crown fire. The crown fuels were mainly affected by the stand age, altitude, DBH, and tree height, while the floor fuels were mainly by the canopy density, slope grade, altitude, and stand age.

Transcriptome characterisation of Pinus tabuliformis and evolution of genes in the Pinus phylogeny

PubMed Central

2013-01-01

Background The Chinese pine (Pinus tabuliformis) is an indigenous conifer species in northern China but is relatively underdeveloped as a genomic resource; thus, limiting gene discovery and breeding. Large-scale transcriptome data were obtained using a next-generation sequencing platform to compensate for the lack of P. tabuliformis genomic information. Results The increasing amount of transcriptome data on Pinus provides an excellent resource for multi-gene phylogenetic analysis and studies on how conserved genes and functions are maintained in the face of species divergence. The first P. tabuliformis transcriptome from a normalised cDNA library of multiple tissues and individuals was sequenced in a full 454 GS-FLX run, producing 911,302 sequencing reads. The high quality overlapping expressed sequence tags (ESTs) were assembled into 46,584 putative transcripts, and more than 700 SSRs and 92,000 SNPs/InDels were characterised. Comparative analysis of the transcriptome of six conifer species yielded 191 orthologues, from which we inferred a phylogenetic tree, evolutionary patterns and calculated rates of gene diversion. We also identified 938 fast evolving sequences that may be useful for identifying genes that perhaps evolved in response to positive selection and might be responsible for speciation in the Pinus lineage. Conclusions A large collection of high-quality ESTs was obtained, de novo assembled and characterised, which represents a dramatic expansion of the current transcript catalogues of P. tabuliformis and which will gradually be applied in breeding programs of P. tabuliformis. Furthermore, these data will facilitate future studies of the comparative genomics of P. tabuliformis and other related species. PMID:23597112

A consensus genetic map for Pinus taeda and Pinus elliottii and extent of linkage disequilibrium in two genotype-phenotype discovery populations of Pinua taeda

Treesearch

Jared W. Westbrook; Vikram E. Chhatre; Le-Shin Wu; Srikar Chamala; Leandro Gomide Neves; Patricio Munoz; Pedro J. Martinez-Garcia; David B. Neale; Matias Kirst; Keithanne Mockaitis; C. Dana Nelson; Gary F. Peter; John M. Davis; Craig S. Echt

2015-01-01

A consensus genetic map for Pinus taeda (loblolly pine) and Pinus elliottii (slash pine) was constructed by merging three previously published P. taeda maps with a map from a pseudo-backcross between P. elliottii and P. taeda. The consensus map positioned 3856 markers via...

Maintaining Low Voiding Solder Die Attach for Power Die While Minimizing Die Tilt

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hamm, Randy; Peterson, Kenneth A.

2015-10-01

This paper addresses work to minimize voiding and die tilt in solder attachment of a large power die, measuring 9.0 mm X 6.5 mm X 0.1 mm (0.354” x 0.256” x 0.004”), to a heat spreader. As demands for larger high power die continue, minimizing voiding and die tilt is of interest for improved die functionality, yield, manufacturability, and reliability. High-power die generate considerable heat, which is important to dissipate effectively through control of voiding under high thermal load areas of the die while maintaining a consistent bondline (minimizing die tilt). Voiding was measured using acoustic imaging and die tiltmore » was measured using two different optical measurement systems. 80Au-20Sn solder reflow was achieved using a batch vacuum solder system with optimized fixturing. Minimizing die tilt proved to be the more difficult of the two product requirements to meet. Process development variables included tooling, weight and solder preform thickness.« less

Composition and structure of Pinus koraiensis mixed forest respond to spatial climatic changes.

PubMed

Zhang, Jingli; Zhou, Yong; Zhou, Guangsheng; Xiao, Chunwang

2014-01-01

Although some studies have indicated that climate changes can affect Pinus koraiensis mixed forest, the responses of composition and structure of Pinus koraiensis mixed forests to climatic changes are unknown and the key climatic factors controlling the composition and structure of Pinus koraiensis mixed forest are uncertain. Field survey was conducted in the natural Pinus koraiensis mixed forests along a latitudinal gradient and an elevational gradient in Northeast China. In order to build the mathematical models for simulating the relationships of compositional and structural attributes of the Pinus koraiensis mixed forest with climatic and non-climatic factors, stepwise linear regression analyses were performed, incorporating 14 dependent variables and the linear and quadratic components of 9 factors. All the selected new models were computed under the +2°C and +10% precipitation and +4°C and +10% precipitation scenarios. The Max Temperature of Warmest Month, Mean Temperature of Warmest Quarter and Precipitation of Wettest Month were observed to be key climatic factors controlling the stand densities and total basal areas of Pinus koraiensis mixed forest. Increased summer temperatures and precipitations strongly enhanced the stand densities and total basal areas of broadleaf trees but had little effect on Pinus koraiensis under the +2°C and +10% precipitation scenario and +4°C and +10% precipitation scenario. These results show that the Max Temperature of Warmest Month, Mean Temperature of Warmest Quarter and Precipitation of Wettest Month are key climatic factors which shape the composition and structure of Pinus koraiensis mixed forest. Although the Pinus koraiensis would persist, the current forests dominated by Pinus koraiensis in the region would all shift and become broadleaf-dominated forests due to the dramatic increase of broadleaf trees under the future global warming and increased precipitation.

Partial cambial mortality in high-elevation Pinus aristata (Pinaceae)

Treesearch

Andrew J. Schauer; Anna W. Schoettle; Richard L. Boyce

2001-01-01

Partial cambial mortality is a growth form that is characteristic of Pinus aristata trees. To better elucidate their cambial death pattern, tree size and aspect of cambial death data were gathered from three Pinus aristata forests in central Colorado, USA. Stripping frequency tended to be higher for larger diameter classes. Partial cambial mortality exhibits...

Strong resilience of soil respiration components to drought-induced die-off resulting in forest secondary succession.

PubMed

Barba, Josep; Curiel Yuste, Jorge; Poyatos, Rafael; Janssens, Ivan A; Lloret, Francisco

2016-09-01

How forests cope with drought-induced perturbations and how the dependence of soil respiration on environmental and biological drivers is affected in a warming and drying context are becoming key questions. The aims of this study were to determine whether drought-induced die-off and forest succession were reflected in soil respiration and its components and to determine the influence of climate on the soil respiration components. We used the mesh exclusion method to study seasonal variations in soil respiration (R S) and its components: heterotrophic (R H) and autotrophic (R A) [further split into fine root (R R) and mycorrhizal respiration (R M)] in a mixed Mediterranean forest where Scots pine (Pinus sylvestris L.) is undergoing a drought-induced die-off and is being replaced by holm oak (Quercus ilex L.). Drought-induced pine die-off was not reflected in R S nor in its components, which denotes a high functional resilience of the plant and soil system to pine die-off. However, the succession from Scots pine to holm oak resulted in a reduction of R H and thus in an important decrease of total respiration (R S was 36 % lower in holm oaks than in non-defoliated pines). Furthermore, R S and all its components were strongly regulated by soil water content-and-temperature interaction. Since Scots pine die-off and Quercus species colonization seems to be widely occurring at the driest limit of the Scots pine distribution, the functional resilience of the soil system over die-off and the decrease of R S from Scots pine to holm oak could have direct consequences for the C balance of these ecosystems.

Germination and early seedling growth of Pinus densata Mast. provenances

Treesearch

Yulan Xu; Nianhui Cai; Bin He; Ruili Zhang; Wei Zhao; Jianfeng Mao; Anan Duan; Yue Li; Keith Woeste

2016-01-01

We studied seed germination and early seedling growth of Pinus densata to explore the range of variability within the species and to inform afforestation practices. Phenotypes were evaluated at a forest tree nursery under conditions that support Pinus yunnanensis, one of the presumed parental species of P. densata...

Accurate defect die placement and nuisance defect reduction for reticle die-to-die inspections

NASA Astrophysics Data System (ADS)

Wen, Vincent; Huang, L. R.; Lin, C. J.; Tseng, Y. N.; Huang, W. H.; Tuo, Laurent C.; Wylie, Mark; Chen, Ellison; Wang, Elvik; Glasser, Joshua; Kelkar, Amrish; Wu, David

2015-10-01

Die-to-die reticle inspections are among the simplest and most sensitive reticle inspections because of the use of an identical-design neighboring-die for the reference image. However, this inspection mode can have two key disadvantages: (1) The location of the defect is indeterminate because it is unclear to the inspector whether the test or reference image is defective; and (2) nuisance and false defects from mask manufacturing noise and tool optical variation can limit the usable sensitivity. The use of a new sequencing approach for a die-to-die inspection can resolve these issues without any additional scan time, without sacrifice in sensitivity requirement, and with a manageable increase in computation load. In this paper we explore another approach for die-to-die inspections using a new method of defect processing and sequencing. Utilizing die-to-die double arbitration during defect detection has been proven through extensive testing to generate accurate placement of the defect in the correct die to ensure efficient defect disposition at the AIMS step. The use of this method maintained the required inspection sensitivity for mask quality as verified with programmed-defectmask qualification and then further validated with production masks comparing the current inspection approach to the new method. Furthermore, this approach can significantly reduce the total number of defects that need to be reviewed by essentially eliminating the nuisance and false defects that can result from a die-to-die inspection. This "double-win" will significantly reduce the effort in classifying a die-to-die inspection result and will lead to improved cycle times.

Evolution of Genome Size and Complexity in Pinus

PubMed Central

Morse, Alison M.; Peterson, Daniel G.; Islam-Faridi, M. Nurul; Smith, Katherine E.; Magbanua, Zenaida; Garcia, Saul A.; Kubisiak, Thomas L.; Amerson, Henry V.; Carlson, John E.; Nelson, C. Dana; Davis, John M.

2009-01-01

Background Genome evolution in the gymnosperm lineage of seed plants has given rise to many of the most complex and largest plant genomes, however the elements involved are poorly understood. Methodology/Principal Findings Gymny is a previously undescribed retrotransposon family in Pinus that is related to Athila elements in Arabidopsis. Gymny elements are dispersed throughout the modern Pinus genome and occupy a physical space at least the size of the Arabidopsis thaliana genome. In contrast to previously described retroelements in Pinus, the Gymny family was amplified or introduced after the divergence of pine and spruce (Picea). If retrotransposon expansions are responsible for genome size differences within the Pinaceae, as they are in angiosperms, then they have yet to be identified. In contrast, molecular divergence of Gymny retrotransposons together with other families of retrotransposons can account for the large genome complexity of pines along with protein-coding genic DNA, as revealed by massively parallel DNA sequence analysis of Cot fractionated genomic DNA. Conclusions/Significance Most of the enormous genome complexity of pines can be explained by divergence of retrotransposons, however the elements responsible for genome size variation are yet to be identified. Genomic resources for Pinus including those reported here should assist in further defining whether and how the roles of retrotransposons differ in the evolution of angiosperm and gymnosperm genomes. PMID:19194510

Influence of seedbed, light environment, and elevated night temperature on growth and carbon allocation in pitch pine (Pinus rigida) and jack pine (Pinus banksiana) seedlings

Treesearch

Michael E. Day; Jessica L. Schedlbauer; William H. Livingston; Michael S. Greenwood; Alan S. White; John C. Brissette

2005-01-01

Jack pine (Pinus banksiana Lamb.) and pitch pine (Pinus rigida Mill.) are two autecologically similar species that occupy generally disjunct ranges in eastern North America. Jack pine is boreal in distribution, while pitch pine occurs at temperate latitudes. The two species co-occur in a small number of stands along a 'tension...

Pinus contorta X banksiana hybrids tested in northern Rocky Mountains

Treesearch

G. E. Rehfeldt; J. E. Lotan

1970-01-01

Between 1950 and 1955 hybrid progenies of lodgepole pine (Pinus contorta Dougl.) X jack pine (Pinus banksiana Lamb.) were tested to determine whether adaptation and performance in Montana and Idaho justified improvement of lodgepole pine by hybridization. Average heights, diameters, and survival rates of hybrids, of jack pines native to the Lake States, and of...

Greek Pinus essential oils: larvicidal activity and repellency against Aedes albopictus (Diptera: Culicidae).

PubMed

Koutsaviti, Katerina; Giatropoulos, Athanassios; Pitarokili, Danae; Papachristos, Dimitrios; Michaelakis, Antonios; Tzakou, Olga

2015-02-01

The needle volatiles metabolites of seven Pinus spp.: Pinus nigra (3 samples), Pinus stankewiczii, Pinus brutia, Pinus halepensis, Pinus canariensis, Pinus pinaster and Pinus strobus from Greece were determined by gas chromatography and gas chromatography-mass spectrometry. P. nigra and P. canariensis essential oils were dominated by α-pinene (24.9-28.9 % and 15 %, respectively) and germacrene D (20.3-31.9 % and 55.8 %, respectively), whereas P. brutia and P. strobus by α-pinene (20.6 % and 31.4 %, respectively) and β-pinene (31.7 % and 33.6 %, respectively). P. halepensis and P. pinaster oils were characterized by β-caryophyllene (28.5 % and 22.5 %, respectively). Finally, β-pinene (31.4 %), germacrene D (23.3 %) and α-pinene (17.5 %) were the most abundant compounds in the needle oil of P. stankewiczii. Additionally the larvicidal and repellent properties of their essential oils were evaluated against Aedes albopictus, a mosquito of great ecological and medical importance. The results of bioassays revealed that repellent abilities of the tested essential oils were more potent than their larvicidal activities. The essential oils of P. brutia, P. halepensis and P. stankewiczii presented considerable larvicidal activity (LC50 values 67.04 mgL(-1) and 70.21 mgL(-1), respectively), while the others were weak to inactive against larvae. The essential oils of P. halepensis, P. brutia, and P. stankewiczii presented a high repellent activity, even at the dose of 0.2 μL cm(-2), while in the dose of 0.4 μL cm(-2), almost all the tested EOs displayed protection against the mosquito.

Characterization of phenolic compounds in Pinus laricio needles and their responses to prescribed burnings.

PubMed

Cannac, Magali; Pasqualini, Vanina; Greff, Stéphane; Fernandez, Catherine; Ferrat, Lila

2007-07-30

Fire is a dominant ecological factor in Mediterranean-type ecosystems. Management strategies include prescribed (controlled) burning, which has been used in the management of several species, such as Pinus nigra ssp laricio var. Corsicana, a pine endemic to Corsica of great ecological and economic importance. The effects of prescribed burning on Pinus laricio have been little studied. The first aim of this study was to characterize total and simple phenolic compounds in Pinus laricio. The second aim was to understand: i) the short term (one to three months) and medium term (three years) effects of prescribed burning, and ii) the effects of periodic prescribed burning on the production of phenolic compounds in Pinus laricio. The first result of this study is the presence of total and simple phenolic compounds in the needles of Pinus laricio. 3-Vanillyl propanol is the major compound. After a prescribed burning, the synthesis of total phenolic compounds increases in Pinus laricio for a period of three months. Total phenolic compounds could be used as bioindicators for the short-term response of Pinus laricio needles to prescribed burning. Simple phenolic compounds do not seem to be good indicators of the impact of prescribed burning because prescribed burnings are low in intensity.

Changes in whole-tree water relations during ontogeny of Pinus flexilis and Pinus ponderosa in a high-elevation meadow.

PubMed

Fischer, Dylan G; Kolb, Thomas E; DeWald, Laura E

2002-07-01

We measured sap flux in Pinus ponderosa Laws. and Pinus flexilis James trees in a high-elevation meadow in northern Arizona that has been invaded by conifers over the last 150 years. Sap flux and environmental data were collected from July 1 to September 1, 2000, and used to estimate leaf specific transpiration rate (El), canopy conductance (Gc) and whole-plant hydraulic conductance (Kh). Leaf area to sapwood area ratio (LA/SA) increased with increasing tree size in P. flexilis, but decreased with increasing tree size in P. ponderosa. Both Gc and Kh decreased with increasing tree size in P. flexilis, and showed no clear trends with tree size in P. ponderosa. For both species, Gc was lower in the summer dry season than in the summer rainy season, but El did not change between wet and dry summer seasons. Midday water potential (Psi(mid)) did not change across seasons for either species, whereas predawn water potential (Psi(pre)) tracked variation in soil water content across seasons. Pinus flexilis showed greater stomatal response to vapor pressure deficit (VPD) and maintained higher Psi(mid) than P. ponderosa. Both species showed greater sensitivity to VPD at high photosynthetically active radiation (PAR; > 2500 micromol m-2 s-1) than at low PAR (< 2500 micromol m-2 s-1). We conclude that the direction of change in Gc and Kh with increasing tree size differed between co-occurring Pinus species, and was influenced by changes in LA/SA. Whole-tree water use and El were similar between wet and dry summer seasons, possibly because of tight stomatal control over water loss. 2002 Heron Publishing--Victoria, Canada

Seasonal variations in red pine (Pinus resinosa) and jack pine (Pinus banksiana) foliar physio-chemistry and their potential influence on stand-scale wildland fire behavior

Treesearch

Matt Jolly; John Hintz; Rodman L. Linn; Rachael C. Kropp; Elliot T. Conrad; Russell A. Parsons; Judith Winterkamp

2016-01-01

The 'Spring Dip' in conifer live foliar moisture content (LFMC) has been well documented but the actual drivers of these variations have not been fully investigated. Here we span this knowledge gap by measuring LFMC, foliar chemistry, foliar density and foliar flammability on new and old foliage for an entire year from both Pinus resinosa (red pine) and Pinus...

Interannual variations in needle and sapwood traits of Pinus edulis branches under an experimental drought

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guerin, Marceau; Martin-Benito, Dario; von Arx, Georg

In recent years, widespread forest mortality in response to drought has been documented worldwide (Allen, Breshears & McDowell 2015). An example of widespread and rapid increase in drought-induced mortality, or die-off, was observed for Pinus edulis Engelm. across the Southwestern USA in response to several years of reduced rainfall and high vapor pressure deficits (VPD) (Breshears et al. 2009; Allen et al. 2010; Williams et al. 2013). Although stomatal closure under drought has been hypothesized to increase mortality through carbon starvation (McDowell et al. 2008; Breshears et al. 2009), more evidences exist for mortality being caused by hydraulic failure (Plautmore » et al. 2012; McDowell et al. 2013; Sevanto et al. 2014; Garcia-Forner et al. 2016). Regardless of the mechanism of drought-induced decline, maintaining a positive supply of water to the foliage is critical for tree functioning and survival.« less

Interannual variations in needle and sapwood traits of Pinus edulis branches under an experimental drought

DOE PAGES

Guerin, Marceau; Martin-Benito, Dario; von Arx, Georg; ...

2018-01-05

In recent years, widespread forest mortality in response to drought has been documented worldwide (Allen, Breshears & McDowell 2015). An example of widespread and rapid increase in drought-induced mortality, or die-off, was observed for Pinus edulis Engelm. across the Southwestern USA in response to several years of reduced rainfall and high vapor pressure deficits (VPD) (Breshears et al. 2009; Allen et al. 2010; Williams et al. 2013). Although stomatal closure under drought has been hypothesized to increase mortality through carbon starvation (McDowell et al. 2008; Breshears et al. 2009), more evidences exist for mortality being caused by hydraulic failure (Plautmore » et al. 2012; McDowell et al. 2013; Sevanto et al. 2014; Garcia-Forner et al. 2016). Regardless of the mechanism of drought-induced decline, maintaining a positive supply of water to the foliage is critical for tree functioning and survival.« less

Method of extruding and packaging a thin sample of reactive material including forming the extrusion die

DOEpatents

Lewandowski, Edward F.; Peterson, Leroy L.

1985-01-01

This invention teaches a method of cutting a narrow slot in an extrusion die with an electrical discharge machine by first drilling spaced holes at the ends of where the slot will be, whereby the oil can flow through the holes and slot to flush the material eroded away as the slot is being cut. The invention further teaches a method of extruding a very thin ribbon of solid highly reactive material such as lithium or sodium through the die in an inert atmosphere of nitrogen, argon or the like as in a glovebox. The invention further teaches a method of stamping out sample discs from the ribbon and of packaging each disc by sandwiching it between two aluminum sheets and cold welding the sheets together along an annular seam beyond the outer periphery of the disc. This provides a sample of high purity reactive material that can have a long shelf life.

Method of extruding and packaging a thin sample of reactive material, including forming the extrusion die

DOEpatents

Lewandowski, E.F.; Peterson, L.L.

1981-11-30

This invention teaches a method of cutting a narrow slot in an extrusion die with an electrical discharge machine by first drilling spaced holes at the ends of where the slot will be, whereby the oil can flow through the holes and slot to flush the material eroded away as the slot is being cut. The invention further teaches a method of extruding a very thin ribbon of solid highly reactive material such as lithium or sodium through the die in an inert atmosphere of nitrogen, argon, or the like as in a glovebox. The invention further teaches a method of stamping out sample discs from the ribbon and of packaging each disc by sandwiching it between two aluminum sheets and cold welding the sheets together along an annular seam beyond the outer periphery of the disc. This provides a sample of high purity reactive material that can have a long shelf life.

Resistance to white pine blister rust in Pinus flexilis and P

Treesearch

Anna W. Schoettle; Richard A. Sniezko; Angelia Kegley; Jerry Hill; Kelly S. Burns

2010-01-01

The non-native fungus Cronartium ribicola, that causes white pine blister rust (WPBR), is impacting or threatening limber pine, Pinus flexilis, and Rocky Mountain bristlecone pine, Pinus aristata. In the Southern Rockies, where the rust invasion is still expanding, we have the opportunity to be proactive and prepare the landscape for invasion. Genetic...

Tree die-off in response to global change-type drought: Mortality insights from a decade of plant water potential measurements

USGS Publications Warehouse

Breshears, D.D.; Myers, O.B.; Meyer, Clifton W.; Barnes, F.J.; Zou, C.B.; Allen, Craig D.; McDowell, N.G.; Pockman, W. T.

2009-01-01

Global climate change is projected to produce warmer, longer, and more frequent droughts, referred to here as “global change-type droughts”, which have the potential to trigger widespread tree die-off. However, drought-induced tree mortality cannot be predicted with confidence, because long-term field observations of plant water stress prior to, and culminating in, mortality are rare, precluding the development and testing of mechanisms. Here, we document plant water stress in two widely distributed, co-occurring species, piñon pine (Pinus edulis) and juniper (Juniperus monosperma), over more than a decade, leading up to regional-scale die-off of piñon pine trees in response to global change-related drought. Piñon leaf water potentials remained substantially below their zero carbon assimilation point for at least 10 months prior to dying, in contrast to those of juniper, which rarely dropped below their zero-assimilation point. These data suggest that piñon mortality was driven by protracted water stress, leading to carbon starvation and associated increases in susceptibility to other disturbances (eg bark beetles), a finding that should help to improve predictions of mortality during drought.

Pinus glabra Walt. Spruce Pine

Treesearch

Susan V. Kossuth; J.L. Michael

1991-01-01

Spruce pine (Pinus glabra), also called cedar pine, Walter pine, or bottom white pine, is a medium-sized tree that grows in limited numbers in swamps, river valleys, on hummocks, and along river banks of the southern Coastal Plain. Its wood is brittle, close-grained, nondurable, and is of limited commercial importance.

Silvics of whitebark pine (Pinus albicaulis)

Treesearch

Stephen F. Arno; Raymond J. Hoff

1989-01-01

Whitebark pine (Pinus albicaulis) is a long-lived tree inhabiting the upper subalpine forest and timberline zone on high mountains of Western North America. The species' habitat, life history, growth and yield, mortality factors, special uses, and genetics are described.

How do trees die? A test of the hydraulic failure and carbon starvation hypotheses

PubMed Central

Sevanto, Sanna; Mcdowell, Nate G; Dickman, L Turin; Pangle, Robert; Pockman, William T

2014-01-01

Despite decades of research on plant drought tolerance, the physiological mechanisms by which trees succumb to drought are still under debate. We report results from an experiment designed to separate and test the current leading hypotheses of tree mortality. We show that piñon pine (Pinus edulis) trees can die of both hydraulic failure and carbon starvation, and that during drought, the loss of conductivity and carbohydrate reserves can also co-occur. Hydraulic constraints on plant carbohydrate use determined survival time: turgor loss in the phloem limited access to carbohydrate reserves, but hydraulic control of respiration prolonged survival. Our data also demonstrate that hydraulic failure may be associated with loss of adequate tissue carbohydrate content required for osmoregulation, which then promotes failure to maintain hydraulic integrity. PMID:23730972

Rust resistance in seedling families of Pinus albicaulis and Pinus strobiformis and implications for restoration

Treesearch

R. A. Sniezko; A. Kegley; R. Danchok; J. Hamlin; J. Hill; D. Conklin

2011-01-01

Infection and mortality levels from Cronartium ribicola, the fungus causing white pine blister rust, are very high in parts of the geographic range of Pinus albicaulis (whitebark pine) and P. strobiformis (Southwestern white pine). Genetic resistance to this non-native fungus will be one of the key factors in maintaining or restoring populations of these species in...

Influence of shear cutting parameters on the fatigue behavior of a dual-phase steel

NASA Astrophysics Data System (ADS)

Paetzold, I.; Dittmann, F.; Feistle, M.; Golle, R.; Haefele, P.; Hoffmann, H.; Volk, W.

2017-09-01

The influence of the edge condition of car body and chassis components made of steel sheet on fatigue behavior under dynamic loading presents a major challenge for automotive manufacturers and suppliers. The calculated lifetime is based on material data determined by the fatigue testing of specimens with polished edges. Prototype components are often manufactured by milling or laser cutting, whereby in practice, the series components are produced by shear cutting due to its cost-efficiency. Since the fatigue crack in such components usually starts from a shear cut edge, the calculated and experimental determined lifetime will vary due to the different conditions at the shear cut edges. Therefore, the material data determined with polished edges can result in a non-conservative component design. The aim of this study is to understand the relationship between the shear cutting process and the fatigue behavior of a dual-phase steel sheet. The geometry of the shear cut edge as well as the depth and degree of work hardening in the shear affected zone can be adjusted by using specific shear cutting parameters, such as die clearance and cutting edge radius. Stress-controlled fatigue tests of unnotched specimens were carried out to compare the fatigue behavior of different edge conditions. By evaluating the results of the fatigue experiments, influential shear cutting parameters on fatigue behavior were identified. It was possible to assess investigated shear cutting strategies regarding the fatigue behavior of a high-strength steel DP800.

Sexual stability in the nearly dioecious Pinus johannis (Pinaceae).

PubMed

Flores-Rentería, Lluvia; Molina-Freaner, Francisco; Whipple, Amy V; Gehring, Catherine A; Domínguez, C A

2013-03-01

Even though dioecy is a dominant sexual system among gymnosperms, little is known about its evolutionary history. Pinus johannis may represent a model system because unisexual and monoecious individuals compose its populations. The presence of unisexual individuals in other Pinus species is a consequence of sexual lability. Here we determined whether P. johannis represents the first example of a dioecious or nearly dioecious reproductive system in conifers by evaluating its sexual stability. • To assess the stability of sexual expression, we quantified the proportion of male vs. female reproductive structures produced by trees over multiple years and tested for the presence of sexual dimorphism. Sexual lability hypotheses were also examined by looking at the relationship between environmental factors and sexual expression and by comparing the reproductive behavior of P. johannis with its closest labile relative, P. edulis. • Pinus johannis is nearly dioecious: ~99% of individuals are unisexual or express a low proportion of the opposite gender with few changes in sexual expression through time. We found sexual dimorphism consistent with sexual stability. Sexual expression did not vary with tree size/age, abiotic environment, or herbivore removal, providing evidence against sexual lability. Individuals of P. johannis tended to produce only male or female strobili, whereas those of P. edulis were mainly monoecious with a gradient in the female to male strobili ratio. • This study represents the first report of a nearly stable dioecious Pinus species. The variety of sexual morphs coexisting in the same population makes P. johannis a model for studying the evolution of dioecy in gymnosperms.

Cutting

MedlinePlus

... Staying Safe Videos for Educators Search English Español Cutting KidsHealth / For Teens / Cutting What's in this article? ... Getting Help Print en español Cortarse What Is Cutting? Emma's mom first noticed the cuts when Emma ...

An analytical method on the surface residual stress for the cutting tool orientation

NASA Astrophysics Data System (ADS)

Li, Yueen; Zhao, Jun; Wang, Wei

2010-03-01

The residual stress is measured by choosing 8 kinds orientations on cutting the H13 dies steel on the HSM in the experiment of this paper. The measured data shows on that the residual stress exists periodicity for the different rake angle (β) and side rake angle (θ) parameters, further study find that the cutting tool orientations have closed relationship with the residual stresses, and for the original of the machined residual stress on the surface from the cutting force and the axial force, it can be gained the simply model of tool-workpiece force, using the model it can be deduced the residual stress model, which is feasible to calculate the size of residual stress. And for almost all the measured residual stresses are compressed stress, the compressed stress size and the direction could be confirmed by the input data for the H13 on HSM. As the result, the residual stress model is the key for optimization of rake angle (β) and side rake angle (θ) in theory, using the theory the more cutting mechanism can be expressed.

Preliminary overview of the first extensive rust resistance screening tests of Pinus flexilis and Pinus aristata

Treesearch

Anna W. Schoettle; Richard A. Sniezko; Angelia Kegley; Kelly S. Burns

2011-01-01

Limber pine ( Pinus flexilis James) and Rocky Mountain bristlecone pine (P. aristata Engelm.; hereafter referred to as bristlecone pine) are the dominant pines that occupy high elevation habitats of the southern Rockies. Bristlecone pine is primarily a subalpine and tree-line species while limber pine in the southern Rocky Mountains grows from 1600 m in the short grass...

Packaged die heater

DOEpatents

Spielberger, Richard; Ohme, Bruce Walker; Jensen, Ronald J.

2011-06-21

A heater for heating packaged die for burn-in and heat testing is described. The heater may be a ceramic-type heater with a metal filament. The heater may be incorporated into the integrated circuit package as an additional ceramic layer of the package, or may be an external heater placed in contact with the package to heat the die. Many different types of integrated circuit packages may be accommodated. The method provides increased energy efficiency for heating the die while reducing temperature stresses on testing equipment. The method allows the use of multiple heaters to heat die to different temperatures. Faulty die may be heated to weaken die attach material to facilitate removal of the die. The heater filament or a separate temperature thermistor located in the package may be used to accurately measure die temperature.

On the benefit of high resolution and low aberrations for in-die mask registration metrology

NASA Astrophysics Data System (ADS)

Beyer, Dirk; Seidel, Dirk; Heisig, Sven; Steinert, Steffen; Töpfer, Susanne; Scherübl, Thomas; Hetzler, Jochen

2014-10-01

With the introduction of complex lithography schemes like double and multi - patterning and new design principles like gridded designs with cut masks the requirements for mask to mask overlay have increased dramatically. Still, there are some good news too for the mask industry since more mask are needed and qualified. Although always confronted with throughput demands, latest writing tool developments are able to keep pace with ever increasing pattern placement specs not only for global signatures but for in-die features within the active area. Placement specs less than 3nm (max. 3 Sigma) are expected and needed in all cases in order to keep the mask contribution to the overall overlay budget at an accepted level. The qualification of these masks relies on high precision metrology tools which have to fulfill stringent metrology as well as resolution constrains at the same time. Furthermore, multi-patterning and gridded designs with pinhole type cut masks are drivers for a paradigm shift in registration metrology from classical registration crosses to in-die registration metrology on production features. These requirements result in several challenges for registration metrology tools. The resolution of the system must be sufficiently high to resolve small production features. At the same time tighter repeatability is required. Furthermore, tool induced shift (TIS) limit the accuracy of in-die measurements. This paper discusses and demonstrates the importance of low illumination wavelength together with low aberrations for best contrast imaging for in-die registration metrology. Typical effects like tool induced shift are analyzed and evaluated using the ZEISS PROVE® registration metrology tool. Additionally, we will address performance gains when going to higher resolution. The direct impact on repeatability for small features by registration measurements will be discussed as well.

Genetic transformation of Pinus palustris (longleaf pine)

Treesearch

Alex M. Diner

1999-01-01

Longleaf pine (Pinus palustris Mill.) is an important softwood species in the Southeast United States. In presettlement times, this species occupied extensive, pure stands throughout the Atlantic and Gulf Coastal Plains from southeastern Virginia to eastern Texas, as well as south...

Paleoclimatic implications of glacial and postglacial refugia for Pinus pumila in western Beringia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anderson, P M; Lozhkin, A V; Solomatkina, T B

Palynological results from Julietta Lake currently provide the most direct evidence to support the existence of a glacial refugium for Pinus pumila in mountains of southwestern Beringia. Both percentages and accumulation rates indicate the evergreen shrub survived until at least {approx}19,000 14C yr B.P. in the Upper Kolyma region. Percentage data suggest numbers dwindled into the late glaciation, whereas pollen accumulation rates point towards a more rapid demise shortly after {approx}19,000 14C yr B.P. Pinus pumila did not re-establish in any great numbers until {approx}8100 14C yr B.P., despite the local presence {approx}9800 14C yr B.P. of Larix dahurica, whichmore » shares similar summer temperature requirements. The postglacial thermal maximum (in Beringia {approx}11,000-9000 14C yr B.P.) provided Pinus pumila shrubs with equally harsh albeit different conditions for survival than those present during the LGM. Regional records indicate that in this time of maximum warmth Pinus pumila likely sheltered in a second, lower-elevation refugium. Paleoclimatic models and modern ecology suggest that shifts in the nature of seasonal transitions and not only seasonal extremes have played important roles in the history of Pinus pumila over the last {approx}21,000 14C yr B.P.« less

Belowground legacies of Pinus contorta invasion and removal result in multiple mechanisms of invasional meltdown.

PubMed

Dickie, Ian A; St John, Mark G; Yeates, Gregor W; Morse, Chris W; Bonner, Karen I; Orwin, Kate; Peltzer, Duane A

2014-01-01

Plant invasions can change soil biota and nutrients in ways that drive subsequent plant communities, particularly when co-invading with belowground mutualists such as ectomycorrhizal fungi. These effects can persist following removal of the invasive plant and, combined with effects of removal per se, influence subsequent plant communities and ecosystem functioning. We used field observations and a soil bioassay with multiple plant species to determine the belowground effects and post-removal legacy caused by invasion of the non-native tree Pinus contorta into a native plant community. Pinus facilitated ectomycorrhizal infection of the co-occurring invasive tree, Pseudotsuga menziesii, but not conspecific Pinus (which always had ectomycorrhizas) nor the native pioneer Kunzea ericoides (which never had ectomycorrhizas). Pinus also caused a major shift in soil nutrient cycling as indicated by increased bacterial dominance, NO3-N (17-fold increase) and available phosphorus (3.2-fold increase) in soils, which in turn promoted increased growth of graminoids. These results parallel field observations, where Pinus removal is associated with invasion by non-native grasses and herbs, and suggest that legacies of Pinus on soil nutrient cycling thus indirectly promote invasion of other non-native plant species. Our findings demonstrate that multi-trophic belowground legacies are an important but hitherto largely unconsidered factor in plant community reassembly following invasive plant removal. Published by Oxford University Press on behalf of the Annals of Botany Company.

Belowground legacies of Pinus contorta invasion and removal result in multiple mechanisms of invasional meltdown

PubMed Central

Dickie, Ian A.; St John, Mark G.; Yeates, Gregor W.; Morse, Chris W.; Bonner, Karen I.; Orwin, Kate; Peltzer, Duane A.

2013-01-01

Plant invasions can change soil biota and nutrients in ways that drive subsequent plant communities, particularly when co-invading with belowground mutualists such as ectomycorrhizal fungi. These effects can persist following removal of the invasive plant and, combined with effects of removal per se, influence subsequent plant communities and ecosystem functioning. We used field observations and a soil bioassay with multiple plant species to determine the belowground effects and post-removal legacy caused by invasion of the non-native tree Pinus contorta into a native plant community. Pinus facilitated ectomycorrhizal infection of the co-occurring invasive tree, Pseudotsuga menziesii, but not conspecific Pinus (which always had ectomycorrhizas) nor the native pioneer Kunzea ericoides (which never had ectomycorrhizas). Pinus also caused a major shift in soil nutrient cycling as indicated by increased bacterial dominance, NO3-N (17-fold increase) and available phosphorus (3.2-fold increase) in soils, which in turn promoted increased growth of graminoids. These results parallel field observations, where Pinus removal is associated with invasion by non-native grasses and herbs, and suggest that legacies of Pinus on soil nutrient cycling thus indirectly promote invasion of other non-native plant species. Our findings demonstrate that multi-trophic belowground legacies are an important but hitherto largely unconsidered factor in plant community reassembly following invasive plant removal. PMID:25228312

Chemical composition, antimicrobial, insecticidal, phytotoxic and antioxidant activities of Mediterranean Pinus brutia and Pinus pinea resin essential oils.

PubMed

Ulukanli, Zeynep; Karabörklü, Salih; Bozok, Fuat; Ates, Burhan; Erdogan, Selim; Cenet, Menderes; Karaaslan, Merve Göksin

2014-12-01

Essential oils of the resins of Pinus brutia and Pinus pinea were evaluated for their biological potential. Essential oils were characterized using GC-MS and GC/FID. in vitro antimicrobial, phytotoxic, antioxidant, and insecticidal activities were carried out using the direct contact and the fumigant assays, respectively. The chemical profile of the essential oils of the resins of P. pinea and P. brutia included mainly α-pinene (21.39% and 25.40%), β-pinene (9.68% and 9.69%), and caryophyllene (9.12% and 4.81%). The essential oils of P. pinea and P. brutia exerted notable antimicrobial activities on Micrococcus luteus and Bacillus subtilis, insecticidal activities on Ephestia kuehniella eggs, phytotoxic activities on Lactuca sativa, Lepidium sativum, and Portulaca oleracea, as well as antioxidant potential. Indications of the biological activities of the essential oils suggest their use in the formulation of ecofriendly and biocompatible pharmaceuticals. Copyright © 2014 China Pharmaceutical University. Published by Elsevier B.V. All rights reserved.

SPHERICAL DIE

DOEpatents

Livingston, J.P.

1959-01-27

A die is presented for pressing powdered materials into a hemispherical shape of uniforin density and wall thickness comprising a fcmale and male die element held in a stationary spaced relation with the space being equivalent to the wall thickness and defining the hemispherical shape, a pressing ring linearly moveable along the male die element, an inlet to fill the space with powdered materials, a guiding system for moving the pressing ring along the male die element so as to press the powdered material and a heating system for heating the male element so that the powdered material is heated while being pressed.

The extractives of Pinus pinaster wood

Treesearch

Richard W. Hemingway; W. E. Hillis; L. S. Lau

1973-01-01

The extractives in Pinus pinaster wood grown in South Australia were examined as part of an assessment of the suitability of this wood for manufacture of absorbent tissues from bisulphite pulps. The average petroleum solubility of the wood was 2.0% but the amount and composition of the petroleum extract varied widely depending upon the age of the...

Growth, carbon-isotope discrimination, and drought-associated mortality across a Pinus ponderosa elevational transect

USGS Publications Warehouse

McDowell, N.G.; Allen, Craig D.; Marshall, L.

2010-01-01

Drought- and insect-associated tree mortality at low-elevation ecotones is a widespread phenomenon but the underlying mechanisms are uncertain. Enhanced growth sensitivity to climate is widely observed among trees that die, indicating that a predisposing physiological mechanism(s) underlies tree mortality. We tested three, linked hypotheses regarding mortality using a ponderosa pine (Pinus ponderosa) elevation transect that experienced low-elevation mortality following prolonged drought. The hypotheses were: (1) mortality was associated with greater growth sensitivity to climate, (2) mortality was associated with greater sensitivity of gas exchange to climate, and (3) growth and gas exchange were correlated. Support for all three hypotheses would indicate that mortality results at least in part from gas exchange constraints. We assessed growth using basal area increment normalized by tree basal area [basal area increment (BAI)/basal area (BA)] to account for differences in tree size. Whole-crown gas exchange was indexed via estimates of the CO2 partial pressure difference between leaf and atmosphere (pa−pc) derived from tree ring carbon isotope ratios (δ13C), corrected for temporal trends in atmospheric CO2 and δ13C and elevation trends in pressure. Trees that survived the drought exhibited strong correlations among and between BAI, BAI/BA, pa−pc, and climate. In contrast, trees that died exhibited greater growth sensitivity to climate than trees that survived, no sensitivity of pa−pc to climate, and a steep relationship between pa−pc and BAI/BA. The pa−pc results are consistent with predictions from a theoretical hydraulic model, suggesting trees that died had a limited buffer between mean water availability during their lifespan and water availability during drought – i.e., chronic water stress. It appears that chronic water stress predisposed low-elevation trees to mortality during drought via constrained gas exchange. Continued intensification of

Die Soldering in Aluminium Die Casting

DOE Office of Scientific and Technical Information (OSTI.GOV)

Han, Q.; Kenik, E.A.; Viswanathan, S.

2000-03-15

Two types of tests, dipping tests and dip-coating tests were carried out on small steel cylinders using pure aluminum and 380 alloy to investigate the mechanism of die soldering during aluminum die casting. Optical and scanning electron microscopy were used to study the morphology and composition of the phases formed during soldering. A soldering mechanism is postulated based on experimental observations. A soldering critical temperature is postulated at which iron begins to react with aluminum to form an aluminum-rich liquid phase and solid intermetallic compounds. When the temperature at the die surface is higher than this critical temperature, the aluminum-richmore » phase is liquid and joins the die with the casting during the subsequent solidification. The paper discusses the mechanism of soldering for the case of pure aluminum and 380 alloy casting in a steel mold, the factors that promote soldering, and the strength of the bond formed when soldering occurs. conditions, an aluminum-rich soldering layer may also form over the intermetallic layer. Although a significant amount of research has been conducted on the nature of these intermetallics, little is known about the conditions under which soldering occurs.« less

Core Cutting Test with Vertical Rock Cutting Rig (VRCR)

NASA Astrophysics Data System (ADS)

Yasar, Serdar; Osman Yilmaz, Ali

2017-12-01

Roadheaders are frequently used machines in mining and tunnelling, and performance prediction of roadheaders is important for project economics and stability. Several methods were proposed so far for this purpose and, rock cutting tests are the best choice. Rock cutting tests are generally divided into two groups which are namely, full scale rock cutting tests and small scale rock cutting tests. These two tests have some superiorities and deficiencies over themselves. However, in many cases, where rock sampling becomes problematic, small scale rock cutting test (core cutting test) is preferred for performance prediction, since small block samples and core samples can be conducted to rock cutting testing. Common problem for rock cutting tests are that they can be found in very limited research centres. In this study, a new mobile rock cutting testing equipment, vertical rock cutting rig (VRCR) was introduced. Standard testing procedure was conducted on seven rock samples which were the part of a former study on cutting rocks with another small scale rock cutting test. Results showed that core cutting test can be realized successfully with VRCR with the validation of paired samples t-test.

Production of High Quality Die Steels from Large ESR Slab Ingots

NASA Astrophysics Data System (ADS)

Geng, Xin; Jiang, Zhou-hua; Li, Hua-bing; Liu, Fu-bin; Li, Xing

With the rapid development of manufacture industry in China, die steels are in great need of large slab ingot of high quality and large tonnage, such as P20, WSM718R and so on. Solidification structure and size of large slab ingots produced with conventional methods are not satisfied. However, large slab ingots manufactured by ESR process have a good solidification structure and enough section size. In the present research, the new slab ESR process was used to produce the die steels large slab ingots with the maximum size of 980×2000×3200mm. The compact and sound ingot can be manufactured by the slab ESR process. The ultra-heavy plates with the maximum thickness of 410 mm can be obtained after rolling the 49 tons ingots. Due to reducing the cogging and forging process, the ESR for large slab ingots process can increase greatly the yield and production efficiency, and evidently cut off product costs.

Influence of gap-scale disturbance on developmental and successional pathways in Quercus-Pinus stands

Treesearch

T.A. Weber; J.L. Hart; C. Schweitzer; D.C. Dey

2014-01-01

Quercus-Pinus forests of the eastern USA cover millions of hectares and span a variety of ecoregions. Understanding the influence of natural disturbance on developmental and successional pathways is important for managers that wish to sustain Pinus spp. in these mixtures. Quantifying developmental and successional patterns in this...

Crossability and relationships of Pinus muricata (Pinaceae)

Treesearch

Constance I. Millar; William B. Critchfield

1988-01-01

Crossing relationships were studies within and among the variable populations of Pinus muricata to test hypotheses about crossing barriers among certain populations. Crossability was assessed at the level of viable seed production following planned crosses. Populations north of Sea Ranch, Sonoma Co., California, crossed freely with parapatric but...

Effectiveness of mechanical thinning and prescribed burning on fire behavior in Pinus nigra forests in NE Spain.

PubMed

Piqué, Míriam; Domènech, Rut

2018-03-15

Fuel treatments can mitigate present and future impacts of climate change by reducing fire intensity and severity. In recent years, Pinus nigra forests in the Mediterranean basin have been dramatically affected by the new risk of highly intense and extreme fires and its distribution area has been reduced. New tools are necessary for assessing the management of these forests so they can adapt to the challenges to come. Our main goal was to evaluate the effects of different fuel treatments on Mediterranean Pinus nigra forests. We assessed the forest response, in terms of forest structure and fire behavior, to different intensities of low thinning treatments followed by different slash prescriptions (resulting in: light thinning and lop and scatter; light thinning and burn; heavy thinning and lop and scatter; heavy thinning and burn; and, untreated control). Treatments that used fire to decrease the resulting slash were the most effective for reducing active crown fires decreasing the rate of spread and flame length more than 89%. Low thinning had an effect on torching potential, but there was no difference between intensities of thinning. Only an outcoming crown fire could spread actively if it was sustained by a high-enough constant wind speed and enough surface fuel load. Overall, treatments reduce fire intensity and treated areas have a more homogenous fire behavior response than untreated areas. This provides opportunities to extinguish the fire and reduce the probability of trees dying from the fire. It would be helpful to include ecological principles and fire behavior criteria in silvicultural treatment guidelines in order to perform more efficient management techniques in the future. Copyright © 2017 Elsevier B.V. All rights reserved.

Evolution and biogeography of Pinus radiata, with a proposed revision of its quaternary history

Treesearch

Constance I. Millar

1999-01-01

The genus Pinus evolved about 100 million years ago, spreading from centres in eastern North America and western Europe throughout middle latitudes of the supercontinent Laurasia. Many early subsections of Pinus are recorded from fossil remains ofthis period, but it is not until the early Tertiary, when the genus was fragmented by...

Twice cutting method reduces tibial cutting error in unicompartmental knee arthroplasty.

PubMed

Inui, Hiroshi; Taketomi, Shuji; Yamagami, Ryota; Sanada, Takaki; Tanaka, Sakae

2016-01-01

Bone cutting error can be one of the causes of malalignment in unicompartmental knee arthroplasty (UKA). The amount of cutting error in total knee arthroplasty has been reported. However, none have investigated cutting error in UKA. The purpose of this study was to reveal the amount of cutting error in UKA when open cutting guide was used and clarify whether cutting the tibia horizontally twice using the same cutting guide reduced the cutting errors in UKA. We measured the alignment of the tibial cutting guides, the first-cut cutting surfaces and the second cut cutting surfaces using the navigation system in 50 UKAs. Cutting error was defined as the angular difference between the cutting guide and cutting surface. The mean absolute first-cut cutting error was 1.9° (1.1° varus) in the coronal plane and 1.1° (0.6° anterior slope) in the sagittal plane, whereas the mean absolute second-cut cutting error was 1.1° (0.6° varus) in the coronal plane and 1.1° (0.4° anterior slope) in the sagittal plane. Cutting the tibia horizontally twice reduced the cutting errors in the coronal plane significantly (P<0.05). Our study demonstrated that in UKA, cutting the tibia horizontally twice using the same cutting guide reduced cutting error in the coronal plane. Copyright © 2014 Elsevier B.V. All rights reserved.

Ecosystem carbon stocks in Pinus palustris forests

Treesearch

Lisa Samuelson; Tom Stokes; John R. Butnor; Kurt H. Johnsen; Carlos A. Gonzalez-Benecke; Pete Anderson; Jason Jackson; Lorenzo Ferrari; Tim A. Martin; Wendell P. Cropper

2014-01-01

Longleaf pine (Pinus palustris Mill.) restoration in the southeastern United States offers opportunities for carbon (C) sequestration. Ecosystem C stocks are not well understood in longleaf pine forests, which are typically of low density and maintained by prescribed fire. The objectives of this research were to develop allometric equations for...

Glacial Refugium of Pinus pumila (Pall.) Regel in Northeastern Siberia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shilo, N A; Lozhkin, A V; Anderson, P M

One of the most glowing representatives of the Kolyma flora [1], ''Pinus pumila'' (Pall.) Regel (Japanese stone pine), is a typical shrub in larch forests of the northern Okhotsk region, basins of the Kolyma and Indigirka rivers, and high-shrub tundra of the Chukchi Peninsula. It also forms a pine belt in mountains above the forest boundary, which gives way to the grass-underbrush mountain tundra and bald mountains. In the southern Chukchi Peninsula, ''Pinus pumila'' along with ''Duschekia fruticosa'' (Rupr.) Pouzar and ''Betula middendorffii'' Trautv. et C. A. Mey form trailing forests transitional between tundra and taiga [2]. Pinus pumila pollen,more » usually predominating in subfossil spore-and-pollen spectra of northeastern Siberia, is found as single grains or a subordinate component (up 2-3%, rarely 10%) in spectra of lacustrine deposits formed during the last glacial stage (isotope stage 2) in the Preboreal and Boreal times of the Holocene. Sometimes, its content increases to 15-22% in spectra of lacustrine deposits synchronous to the last glacial stage near the northern coast of the Sea of Okhotsk [3], evidently indicating the proximity of Japanese stone pine thickets.« less

HIGH PRESSURE DIES

DOEpatents

Wilson, W.B.

1960-05-31

A press was invented for subjecting specimens of bismuth, urania, yttria, or thoria to high pressures and temperatures. The press comprises die parts enclosing a space in which is placed an electric heater thermally insulated from the die parts so as not to damage them by heat. The die parts comprise two opposed inner frustoconical parts and an outer part having a double frustoconical recess receiving the inner parts. The die space decreases in size as the inner die parts move toward one another against the outer part and the inner parts, though very hard, do not fracture because of the mode of support provided by the outer part.

Influence of die geometry and material selection on the behavior of protective die covers in closed-die forging

NASA Astrophysics Data System (ADS)

Yu, Yingyan; Rosenstock, Dirk; Wolfgarten, Martin; Hirt, Gerhard

2016-10-01

Due to the fact that tooling costs make up to 30% of total costs of the final forged part, the tool life is always one main research topic in closed-die forging [1]. To improve the wear resistance of forging dies, many methods like nitriding and deposition of ceramic layers have been used. However, all these methods will lose its effect after a certain time, then tool repair or exchange is needed, which requires additional time and costs. A new method, which applies an inexpensive and changeable sheet metal on the forging die to protect it from abrasive wear, was firstly proposed in [2]. According to the first investigation, the die cover is effective for decreasing thermal and mechanical loads, but there are still several challenges to overcome in this concept, like wrinkling and thinning of the die cover. Therefore, an experimental study using different geometries and die cover materials is presented within this work. The results indicate the existence of feasible application cases of this concept, since conditions are found under which a die cover made of 22MnB5 still keeps its original shape even after 7 forging cycles.

Pinus ponderosa : A checkered past obscured four species

Treesearch

Ann Willyard; David S. Gernandt; Kevin Potter; Valerie Hipkins; Paula E. Marquardt; Mary Frances Mahalovich; Stephen K. Langer; Frank W. Telewski; Blake Cooper; Connor Douglas; Kristen Finch; Hassani H. Karemera; Julia Lefler; Payton Lea; Austin Wofford

2016-01-01

PREMISE OF THE STUDY: Molecular genetic evidence can help delineate taxa in species complexes that lack diagnostic morphological characters. Pinus ponderosa (Pinaceae; subsection Ponderosae ) is recognized as a problematic taxon: plastid phylogenies of exemplars were paraphyletic, and mitochondrial phylogeography suggested at...

Tree mortality patterns following prescribed fire for Pinus and Abies across the southwestern United States

USGS Publications Warehouse

van Mantgem, Philip J.; Nesmith, Jonathan C. B.; Keifer, MaryBeth; Brooks, Matthew

2012-01-01

The reintroduction of fire to historically fire-prone forests has been repeatedly shown to reduce understory fuels and promote resistance to high severity fire. However, there is concern that prescribed fire may also have unintended consequences, such as high rates of mortality for large trees and fire-tolerant Pinus species. To test this possibility we evaluated mortality patterns for two common genera in the western US, Pinus and Abies, using observations from a national-scale prescribed fire effects monitoring program. Our results show that mortality rates of trees >50 DBH were similar for Pinus (4.6% yr-1) and Abies (4.0% yr-1) 5 years following prescribed fires across seven sites in the southwestern US. In contrast, mortality rates of trees >50 cm DBH differed between Pinus (5.7% yr-1) and Abies (9.0% yr-1). Models of post-fire mortality probabilities suggested statistically significant differences between the genera (after including differences in bark thickness), but accounting for these differences resulted in only small improvements in model classification. Our results do not suggest unusually high post-fire mortality for large trees or for Pinus relative to the other common co-occurring genus, Abies, following prescribed fire in the southwestern US.

Fossils matter: improved estimates of divergence times in Pinus reveal older diversification.

PubMed

Saladin, Bianca; Leslie, Andrew B; Wüest, Rafael O; Litsios, Glenn; Conti, Elena; Salamin, Nicolas; Zimmermann, Niklaus E

2017-04-04

The taxonomy of pines (genus Pinus) is widely accepted and a robust gene tree based on entire plastome sequences exists. However, there is a large discrepancy in estimated divergence times of major pine clades among existing studies, mainly due to differences in fossil placement and dating methods used. We currently lack a dated molecular phylogeny that makes use of the rich pine fossil record, and this study is the first to estimate the divergence dates of pines based on a large number of fossils (21) evenly distributed across all major clades, in combination with applying both node and tip dating methods. We present a range of molecular phylogenetic trees of Pinus generated within a Bayesian framework. We find the origin of crown Pinus is likely up to 30 Myr older (Early Cretaceous) than inferred in most previous studies (Late Cretaceous) and propose generally older divergence times for major clades within Pinus than previously thought. Our age estimates vary significantly between the different dating approaches, but the results generally agree on older divergence times. We present a revised list of 21 fossils that are suitable to use in dating or comparative analyses of pines. Reliable estimates of divergence times in pines are essential if we are to link diversification processes and functional adaptation of this genus to geological events or to changing climates. In addition to older divergence times in Pinus, our results also indicate that node age estimates in pines depend on dating approaches and the specific fossil sets used, reflecting inherent differences in various dating approaches. The sets of dated phylogenetic trees of pines presented here provide a way to account for uncertainties in age estimations when applying comparative phylogenetic methods.

Silvical characteristics of pitch pine (Pinus rigida)

Treesearch

S. Little

1959-01-01

Pitch pine (Pinus rigida Mill.) grows over a wide geographical range - from central Maine to New York and extreme southeastern Ontario, south to Virginia and southern Ohio, and in the mountains to eastern Tennessee, northern Georgia, and western South Carolina. Because it grows mostly on the poorer soils, its distribution is spotty.

Whitebark pine (Pinus albicaulis) assisted migration trial

Treesearch

Sierra C. McLane; Sally N. Aitken

2011-01-01

Assisted migration - the translocation of a species into a climatically-suitable location outside of its current range - has been proposed as a means of saving vulnerable species from extinction as temperatures rise due to climate change. We explore this controversial technique using the keystone wildlife symbiote and ecosystem engineer, whitebark pine (Pinus...

Die Sonne.

NASA Astrophysics Data System (ADS)

der Time-Life Bücher, Redaktion

Contents: 1. Das Antlitz der Sonne. Ein kosmisches Kraftwerk. 2. Erforschung des Innern. Die Beobachtung des Zentralgestirns. 3. Der unstete Nachbar. Geschenke des Sonnenlichts. 4. Ein endloser Partikelstrom. Die Kraft eines solaren Sturms.

Pine seed tree growth and yield on the Crossett Experimental Forest

Treesearch

Don C. Bragg

2010-01-01

In late 2002, three small tracts of loblolly (Pinus taeda) and shortleaf (Pinus echinata) pine on the Crossett Experimental Forest in Ashley County, AR, were cut using a seed tree method. Immediately after harvest, these cutting units averaged 7.7 stems and 13.8 square feet of pine basal area per acre. By 2006, live seed tree...

Identification case of evidence in timber tracing of Pinus radiate, using high-resolution melting (HRM) analysis.

PubMed

Solano, Jaime; Anabalón, Leonardo; Encina, Francisco

2016-03-01

Fast, accurate detection of plant species and their hybrids using molecular tools will facilitate assessment and monitoring of timber tracing evidence. In this study the origin of unknown pine samples is determined for a case of timber theft in the region of Araucania southern Chile. We evaluate the utility of the trnL marker region for species identification applied to pine wood based on High Resolution Melting. This efficient tracing methods can be incorporated into forestry applications such as certification of origin. The object of this work was genotype identification using high-resolution melting (HRM) and trnL approaches for Pinus radiata (Don) in timber tracing evidence. Our results indicate that trnL is a very sensitive marker for delimiting species and HRM analysis was used successfully for genotyping Pinus samples for timber tracing purposes. Genotyping samples by HRM analysis with the trnL1 approach allowed us to differentiate two wood samples from the Pinaceae family: Pinus radiata (Don) and Pseudotsuga menziesii (Mirb.) Franco. The same approach with Pinus trnL wood was not able to discriminate between samples of Pinus radiata, indicating that the samples were genetically indistinguishable, possibly because they have the same genotype at this locus. Timber tracing with HRM analysis is expected to contribute to future forest certification schemes, control of illegal trading, and molecular traceability of Pinus spp. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Phylogenetics of Pinus (Pinaceae) based on nuclear ribosomal DNA internal transcribed spacer region sequences.

PubMed

Liston, A; Robinson, W A; Piñero, D; Alvarez-Buylla, E R

1999-02-01

A 650-bp portion of the nuclear ribosomal DNA internal transcribed spacer region was sequenced in 47 species of Pinus, representing all recognized subsections of the genus, and 2 species of Picea and Cathaya as outgroups. Parsimony analyses of these length variable sequences were conducted using a manual alignment, 13 different automated alignments, elision of the automated alignments, and exclusion of all alignment ambiguous sites. High and moderately supported clades were consistently resolved across the different analyses, while poorly supported clades were inconsistently recovered. Comparison of the topologies highlights taxa of particularly problematic placement including Pinus nelsonii and P. aristata. Within subgenus Pinus, there is moderate support for the monophyly of a narrowly circumscribed subsect. Pinus (=subsect. Sylvestres) and strong support for a clade of North and Central American hard pines. The Himalayan P. roxburghii may be sister species to these "New World hard pines," which have two well-supported subgroups, subsect. Ponderosae and a clade of the remaining five subsections. The position of subsect. Contortae conflicts with its placement in a chloroplast DNA restriction site study. Within subgenus Strobus there is consistent support for the monophyly of a broadly circumscribed subsect. Strobi (including P. krempfii and a polyphyletic subsect. Cembrae) derived from a paraphyletic grade of the remaining soft pines. Relationships among subsects. Gerardianae, Cembroides, and Balfourianae are poorly resolved. Support for the monophyly of subgenus Pinus and subgenus Strobus is not consistently obtained. Copyright 1999 Academic Press.

Die singulation method

DOEpatents

Swiler, Thomas P.; Garcia, Ernest J.; Francis, Kathryn M.

2013-06-11

A method is disclosed for singulating die from a semiconductor substrate (e.g. a semiconductor-on-insulator substrate or a bulk silicon substrate) containing an oxide layer (e.g. silicon dioxide or a silicate glass) and one or more semiconductor layers (e.g. monocrystalline or polycrystalline silicon) located above the oxide layer. The method etches trenches through the substrate and through each semiconductor layer about the die being singulated, with the trenches being offset from each other around at least a part of the die so that the oxide layer between the trenches holds the substrate and die together. The trenches can be anisotropically etched using a Deep Reactive Ion Etching (DRIE) process. After the trenches are etched, the oxide layer between the trenches can be etched away with an HF etchant to singulate the die. A release fixture can be located near one side of the substrate to receive the singulated die.

Die singulation method

DOEpatents

Swiler, Thomas P [Albuquerque, NM; Garcia, Ernest J [Albuquerque, NM; Francis, Kathryn M [Rio Rancho, NM

2014-01-07

A method is disclosed for singulating die from a semiconductor substrate (e.g. a semiconductor-on-insulator substrate or a bulk silicon substrate) containing an oxide layer (e.g. silicon dioxide or a silicate glass) and one or more semiconductor layers (e.g. monocrystalline or polycrystalline silicon) located above the oxide layer. The method etches trenches through the substrate and through each semiconductor layer about the die being singulated, with the trenches being offset from each other around at least a part of the die so that the oxide layer between the trenches holds the substrate and die together. The trenches can be anisotropically etched using a Deep Reactive Ion Etching (DRIE) process. After the trenches are etched, the oxide layer between the trenches can be etched away with a HF etchant to singulate the die. A release fixture can be located near one side of the substrate to receive the singulated die.

Testing Of Choiced Ceramics Cutting Tools At Irregular Interrupted Cut

NASA Astrophysics Data System (ADS)

Kyncl, Ladislav; Malotová, Šárka; Nováček, Pavel; Nicielnik, Henryk; Šoková, Dagmar; Hemžský, Pavel; Pitela, David; Holubjak, Jozef

2015-12-01

This article discusses the test of removable ceramic cutting inserts during machining irregular interrupted cut. Tests were performed on a lathe, with the preparation which simulated us the interrupted cut. By changing the number of plates mounted in a preparation it simulate us a regular or irregular interrupted cut. When with four plates it was regular interrupted cut, the remaining three variants were already irregular cut. It was examined whether it will have the irregular interrupted cutting effect on the insert and possibly how it will change life of inserts during irregular interrupted cut (variable delay between shocks).

Genetic diversity and gene exchange in Pinus oocarpa, a Mesoamerican Pine with resistance to the pitch canker fungus (Fusarium circinatum)

Treesearch

William S. Dvorak; Kevin M. Potter; Valerie D. Hipkins; Gary R. Hodge

2009-01-01

Eleven highly polymorphic microsatellite markers were used to determine the genetic structure and levels of diversity in 51 natural populations of Pinus oocarpa across its geographic range of 3000 km in Mesoamerica. The study also included 17 populations of Pinus patula and Pinus tecunumanii chosen for...

A Consensus Genetic Map for Pinus taeda and Pinus elliottii and Extent of Linkage Disequilibrium in Two Genotype-Phenotype Discovery Populations of Pinus taeda

PubMed Central

Westbrook, Jared W.; Chhatre, Vikram E.; Wu, Le-Shin; Chamala, Srikar; Neves, Leandro Gomide; Muñoz, Patricio; Martínez-García, Pedro J.; Neale, David B.; Kirst, Matias; Mockaitis, Keithanne; Nelson, C. Dana; Peter, Gary F.; Echt, Craig S.

2015-01-01

A consensus genetic map for Pinus taeda (loblolly pine) and Pinus elliottii (slash pine) was constructed by merging three previously published P. taeda maps with a map from a pseudo-backcross between P. elliottii and P. taeda. The consensus map positioned 3856 markers via genotyping of 1251 individuals from four pedigrees. It is the densest linkage map for a conifer to date. Average marker spacing was 0.6 cM and total map length was 2305 cM. Functional predictions of mapped genes were improved by aligning expressed sequence tags used for marker discovery to full-length P. taeda transcripts. Alignments to the P. taeda genome mapped 3305 scaffold sequences onto 12 linkage groups. The consensus genetic map was used to compare the genome-wide linkage disequilibrium in a population of distantly related P. taeda individuals (ADEPT2) used for association genetic studies and a multiple-family pedigree used for genomic selection (CCLONES). The prevalence and extent of LD was greater in CCLONES as compared to ADEPT2; however, extended LD with LGs or between LGs was rare in both populations. The average squared correlations, r2, between SNP alleles less than 1 cM apart were less than 0.05 in both populations and r2 did not decay substantially with genetic distance. The consensus map and analysis of linkage disequilibrium establish a foundation for comparative association mapping and genomic selection in P. taeda and P. elliottii. PMID:26068575

The characteristics of soil and water loss in Pinus Massoniana forest in Quaternary red soil area of south China

NASA Astrophysics Data System (ADS)

Song, Yuejun; Huang, Yanhe; Jie, Yang

2017-08-01

The soil and water loss in Pinus massoniana forests is an urgent environmental problem in the red soil region of southern China.Using the method of field monitoring, by analogy and statistical analysis, The characteristics of soil and water loss of Pinus massoniana forests in Quaternary red soil region under 30 rainfall were analyzed,the results show that the relationship models of rainfall,runoff and sediment of pure Pinus massoniana plot were slightly different from the naked control plot,were all the univariate quadratic linear regression models.the contribution of runoff and sediment in different rain types were different, and the water and soil loss in Pinus massoniana forest was most prominent under moderate rain.The merging effect of sparse Pinus massoniana forest on raindrop, aggravated the degree of soil and water loss to some extent.

The thermal fatigue resistance of H-13 Die Steel for aluminum die casting dies

NASA Technical Reports Server (NTRS)

1982-01-01

The effects of welding, five selected surface coatings, and stress relieving on the thermal fatigue resistance of H-13 Die Steel for aluminum die casting dies were studied using eleven thermal fatigue specimens. Stress relieving was conducted after each 5,000 cycle interval at 1050 F for three hours. Four thermal fatigue specimens were welded with H-13 or maraging steel welding rods at ambient and elevated temperatures and subsequently, subjected to different post-weld heat treatments. Crack patterns were examined at 5,000, 10,000, and 15,000 cycles. The thermal fatigue resistance is expressed by two crack parameters which are the average maximum crack and the average cracked area. The results indicate that a significant improvement in thermal fatigue resistance over the control was obtained from the stress-relieving treatment. Small improvements were obtained from the H-13 welded specimens and from a salt bath nitrogen and carbon-surface treatment. The other surface treatments and welded specimens either did not affect or had a detrimental influence on the thermal fatigue properties of the H-13 die steel.

Lactate clearance cut off for early mortality prediction in adult sepsis and septic shock patients

NASA Astrophysics Data System (ADS)

Sinto, R.; Widodo, D.; Pohan, H. T.

2018-03-01

Previous lactate clearance cut off for early mortality prediction in sepsis and septic shock patient was determined by consensus from small sample size-study. We investigated the best lactate clearance cut off and its ability to predict early mortality in sepsis and septic shock patients. This cohort study was conducted in Intensive Care Unit of CiptoMangunkusumo Hospital in 2013. Patients’ lactate clearance and eight other resuscitationendpoints were recorded, and theoutcome was observed during the first 120 hours. The clearance cut off was determined using receiver operating characteristic (ROC) analysis, and its ability was investigated with Cox’s proportional hazard regression analysis using other resuscitation endpoints as confounders. Total of 268 subjects was included, of whom 70 (26.11%) subjects died within the first 120 hours. The area under ROC of lactate clearance to predict early mortality was 0.78 (95% % confidence interval [CI] 0.71-0.84) with best cut off was <7.5% (sensitivity and specificity 88.99% and 81.4% respectively). Compared with group achieving lactate clearance target, group not achieving lactate clearance target had to increase early mortality risk (adjusted hazard ratio 13.42; 95%CI 7.19-25.07). In conclusion, the best lactate clearance cut off as anearly mortality predictor in sepsis and septic shock patients is 7.5%.

Fibre laser cutting stainless steel: Fluid dynamics and cut front morphology

NASA Astrophysics Data System (ADS)

Pocorni, Jetro; Powell, John; Deichsel, Eckard; Frostevarg, Jan; Kaplan, Alexander F. H.

2017-01-01

In this paper the morphology of the laser cut front generated by fibre lasers was investigated by observation of the 'frozen' cut front, additionally high speed imaging (HSI) was employed to study the fluid dynamics on the cut front while cutting. During laser cutting the morphology and flow properties of the melt film on the cut front affect cut quality parameters such as cut edge roughness and dross (residual melt attached to the bottom of the cut edge). HSI observation of melt flow down a laser cutting front using standard cutting parameters is experimentally problematic because the cut front is narrow and surrounded by the kerf walls. To compensate for this, artificial parameters are usually chosen to obtain wide cut fronts which are unrepresentative of the actual industrial process. This paper presents a new experimental cutting geometry which permits HSI of the laser cut front using standard, commercial parameters. These results suggest that the cut front produced when cutting medium section (10 mm thick) stainless steel with a fibre laser and a nitrogen assist gas is covered in humps which themselves are covered by a thin layer of liquid. HSI observation and theoretical analysis reveal that under these conditions the humps move down the cut front at an average speed of approximately 0.4 m/s while the covering liquid flows at an average speed of approximately 1.1 m/s, with an average melt depth at the bottom of the cut zone of approximately 0.17 mm.

Analysis of three microscopic characters for separating the wood of Pinus contorta and P. ponderosa

Treesearch

Alex C. Wiedenhoeft; Regis B. Miller; Terra J. Theim

2003-01-01

Three microscopic characters were evaluated for the identification of Pinus contorta and Pinus ponderosa. The tangential diameter of the resin canals, including the epithelium, was compared to the tangential diameter of the entire resin canal complex. The latter measurement was shown to give diagnostic results for these species. Data from the examination of ray...

Dimensional control of die castings

NASA Astrophysics Data System (ADS)

Karve, Aniruddha Ajit

The demand for net shape die castings, which require little or no machining, is steadily increasing. Stringent customer requirements are forcing die casters to deliver high quality castings in increasingly short lead times. Dimensional conformance to customer specifications is an inherent part of die casting quality. The dimensional attributes of a die casting are essentially dependent upon many factors--the quality of the die and the degree of control over the process variables being the two major sources of dimensional error in die castings. This study focused on investigating the nature and the causes of dimensional error in die castings. The two major components of dimensional error i.e., dimensional variability and die allowance were studied. The major effort of this study was to qualitatively and quantitatively study the effects of casting geometry and process variables on die casting dimensional variability and die allowance. This was accomplished by detailed dimensional data collection at production die casting sites. Robust feature characterization schemes were developed to describe complex casting geometry in quantitative terms. Empirical modeling was utilized to quantify the effects of the casting variables on dimensional variability and die allowance for die casting features. A number of casting geometry and process variables were found to affect dimensional variability in die castings. The dimensional variability was evaluated by comparisons with current published dimensional tolerance standards. The casting geometry was found to play a significant role in influencing the die allowance of the features measured. The predictive models developed for dimensional variability and die allowance were evaluated to test their effectiveness. Finally, the relative impact of all the components of dimensional error in die castings was put into perspective, and general guidelines for effective dimensional control in the die casting plant were laid out. The results of

Molecular response to water stress in two contrasting Mediterranean pines (Pinus pinaster and Pinus pinea).

PubMed

Perdiguero, Pedro; Barbero, María Del Carmen; Cervera, María Teresa; Collada, Carmen; Soto, Alvaro

2013-06-01

Adaptation to water stress has determined the evolution and diversification of vascular plants. Water stress is forecasted to increase drastically in the next decades in certain regions, such as in the Mediterranean basin. Consequently, a proper knowledge of the response and adaptations to drought stress is essential for the correct management of plant genetic resources. However, most of the advances in the understanding of the molecular response to water stress have been attained in angiosperms, and are not always applicable to gymnosperms. In this work we analyse the transcriptional response of two emblematic Mediterranean pines, Pinus pinaster and Pinus pinea, which show noticeable differences in their performance under water stress. Using microarray analysis, up to 113 genes have been detected as significantly induced by drought in both species. Reliability of expression patterns has been confirmed by RT-PCR. While induced genes with similar profiles in both species can be considered as general candidate genes for the study of drought response in conifers, genes with diverging expression patterns can underpin the differences displayed by these species under water stress. Most promising candidate genes for drought stress response include genes related to carbohydrate metabolism, such as glycosyltransferases or galactosidases, sugar transporters, dehydrins and transcription factors. Additionally, differences in the molecular response to drought and polyethylene-glycol-induced water stress are also discussed. Copyright © 2013 Elsevier Masson SAS. All rights reserved.

Genetic diversity and gene exchange in Pinus oocarpa, a Mesoamerican pine with resistance to the pitch canker fungus (Fusarium circinatum)

Treesearch

W.S. Dvorak; K.M. Potter

2009-01-01

Eleven highly polymorphic microsatellite markers were used to determine the genetic structure and levels of diversity in 51 natural populations of Pinus oocarpa across its geographic range of 3000 km in Mesoamerica. The study also included 17 populations of Pinus patula and Pinus tecunumanii chosen for their resistance or susceptibility to the pitch canker fungus based...

A new C-methylated flavonoid glycoside from Pinus densiflora.

PubMed

Jung, M J; Choi, J H; Chung, H Y; Jung, J H; Choi, J S

2001-12-01

A new C-methyl flavonol glycoside, 5,7,8,4'-tetrahydroxy-3-methoxy-6-methylflavone 8-O-beta-D-glucopyranoside (1), has been isolated from the needles of Pinus densiflora, together with kaempferol 3-O-beta-(6"-acetyl)-galactopyranoside.

Assisted Dying & Disability.

PubMed

Riddle, Christopher A

2017-07-01

This article explores at least two dominant critiques of assisted dying from a disability rights perspective. In spite of these critiques, I conclude that assisted dying ought to be permissible. I arrive at the conclusion that if we respect and value people with disabilities, we ought to permit assisted dying. I do so in the following manner. First, I examine recent changes in legislation that have occurred since the Royal Society of Canada Expert Panel on End-of-Life Decision-Making report, published in this journal. I suggest that these changes are likely to only strengthen opposition to assisted dying from disability rights activists and people with disabilities. Second, I focus on respect for people with disabilities and in particular, respect for their autonomy and decision-making abilities. Third, I explore the opposition to assisted dying that focuses on risk and the vulnerability of people with disabilities. Here I suggest that this risk ought not to be of special concern. Ultimately, I conclude that upholding respect for the disabled requires the legalization of assisted dying, rather than the denial of access in a misguided effort to protect people with disabilities. © 2017 John Wiley & Sons Ltd.

Micromechanical die attachment surcharge

DOEpatents

Filter, William F.; Hohimer, John P.

2002-01-01

An attachment structure is disclosed for attaching a die to a supporting substrate without the use of adhesives or solder. The attachment structure, which can be formed by micromachining, functions purely mechanically in utilizing a plurality of shaped pillars (e.g. round, square or polygonal and solid, hollow or slotted) that are formed on one of the die or supporting substrate and which can be urged into contact with various types of mating structures including other pillars, a deformable layer or a plurality of receptacles that are formed on the other of the die or supporting substrate, thereby forming a friction bond that holds the die to the supporting substrate. The attachment structure can further include an alignment structure for precise positioning of the die and supporting substrate to facilitate mounting the die to the supporting substrate. The attachment structure has applications for mounting semiconductor die containing a microelectromechanical (MEM) device, a microsensor or an integrated circuit (IC), and can be used to form a multichip module. The attachment structure is particularly useful for mounting die containing released MEM devices since these devices are fragile and can otherwise be damaged or degraded by adhesive or solder mounting.

Effects of a clear-cut harvest on soil respiration in a jack pine - Lichen woodland

USGS Publications Warehouse

Striegl, Robert G.; Wickland, K.P.

1998-01-01

Quantification of the components of ecosystem respiration is essential to understanding carbon (C) cycling of natural and disturbed landscapes. Soil respiration, which includes autotrophic and heterotrophic respiration from throughout the soil profile, is the second largest flux in the global carbon cycle. We measured soil respiration (soil CO2 emission) at an undisturbed mature jack pine (Pinus banksiana Lamb.) stand in Saskatchewan (old jack pine, OJP), and at a formerly continuous portion of the stand that was clear-cut during the previous winter (clear-cut, CC). Tree harvesting reduced soil CO2 emission from ???22.5 to ???9.1 mol CO2??m2 for the 1994 growing season. OJP was a small net sink of atmospheric CO2, while CC was a net source of CO2. Winter emissions were similar at both sites. Reduction of soil respiration was attributed to disruption of the soil surface and to the death of tree roots. Flux simulations for CC and OJP identify 40% of CO2 emission at the undisturbed OJP site as near-surface respiration, 25% as deep-soil respiration, and 35% as tree-root respiration. The near-surface component was larger than the estimated annual C input to soil, suggesting fast C turnover and no net C accumulation in these boreal uplands in 1994.

Sputtered protective coatings for die casting dies

NASA Technical Reports Server (NTRS)

Mirtich, M. J.; Nieh, C.-Y.; Wallace, J. F.

1981-01-01

Three experimental research designs investigating candidate materials and processes involved in protective die surface coating procedures by sputter deposition, using ion beam technologies, are discussed. Various pre-test results show that none of the coatings remained completely intact for 15,000 test cycles. The longest lifetime was observed for coatings such as tungsten, platinum, and molybdenum which reduced thermal fatigue, but exhibited oxidation and suppressed crack initiation only as long as the coating did not fracture. Final test results confirmed earlier findings and coatings with Pt and W proved to be the candidate materials to be used on a die surface to increase die life. In the W-coated specimens, which remained intact on the surface after thermal fatigue testing, no oxidation was found under the coating, although a few cracks formed on the surface where the coating broke down. Further research is planned.

Wedge cutting of mild steel by CO 2 laser and cut-quality assessment in relation to normal cutting

NASA Astrophysics Data System (ADS)

Yilbas, B. S.; Karatas, C.; Uslan, I.; Keles, O.; Usta, Y.; Yilbas, Z.; Ahsan, M.

2008-10-01

In some applications, laser cutting of wedge surfaces cannot be avoided in sheet metal processing and the quality of the end product defines the applicability of the laser-cutting process in such situations. In the present study, CO 2 laser cutting of the wedge surfaces as well as normal surfaces (normal to laser beam axis) is considered and the end product quality is assessed using the international standards for thermal cutting. The cut surfaces are examined by the optical microscopy and geometric features of the cut edges such as out of flatness and dross height are measured from the micrographs. A neural network is introduced to classify the striation patterns of the cut surfaces. It is found that the dross height and out of flatness are influenced significantly by the laser output power, particularly for wedge-cutting situation. Moreover, the cut quality improves at certain value of the laser power intensity.

Cytoprotective effects of essential oil of Pinus halepensis L. against aspirin-induced toxicity in IEC-6 cells.

PubMed

Bouzenna, Hafsia; Hfaiedh, Najla; Bouaziz, Mouhamed; Giroux-Metges, Marie-Agnès; Elfeki, Abdelfattah; Talarmin, Hélène

2017-12-01

Essential oils from Pinus species have been reported to have various therapeutic properties. This study was undertaken to identify the chemical composition and cytoprotective effects of the essential oil of Pinus halepensis L. against aspirin-induced damage in cells in vitro. The cytoprotection of the oil against toxicity of aspirin on the small intestine epithelial cells IEC-6 was tested. The obtained results have shown that 35 different compounds were identified. Aspirin induced a decrease in cell viability, and exhibited significant damage to their morphology and an increase in superoxide dismutase (SOD) and catalase (CAT) activities. However, the co-treatment of aspirin with the essential oil of Pinus induced a significant increase in cell viability and a decrease in SOD and CAT activities. Overall, these finding suggest that the essential oil of Pinus halepensis L. has potent cytoprotective effect against aspirin-induced toxicity in IEC-6 cells.

[Effects of selective cutting on the carbon density and net primary productivity of a mixed broadleaved-Korean pine forest in Northeast China].

PubMed

Liu, Qi; Cai, Hui-Ying; Jin, Guang-Ze

2013-10-01

To accurately quantify forest carbon density and net primary productivity (NPP) is of great significance in estimating the role of forest ecosystems in global carbon cycle. By using the forest inventory and allometry approaches, this paper measured the carbon density and NPP of the virgin broadleaved-Korean pine (Pinus koraiensis) forest and of the broadleaved-Korean pine forest after 34 years selective-cutting (the cutting intensity was 30%, and the cutting trees were in large diameter class). The total carbon density of the virgin and selective-cutting broadleaved-Korean pine forests was (397.95 +/- 93.82) and (355.61 +/- 59.37) t C x hm(-2), respectively. In the virgin forest, the carbon density of the vegetation, debris, and soil accounted for 31.0%, 3.1%, and 65.9% of the total carbon pool, respectively; in the selective-cutting forest, the corresponding values were 31.7%, 2.9%, and 65.4%, respectively. No significant differences were observed in the total carbon density and the carbon density of each component between the two forests. The total NPP of the virgin and selective-cutting forests was (36.27 +/- 0.36) and (6.35 +/- 0.70) t C x hm(-2) x a(-1), among which, the NPP of overstory, understory, and fine roots in virgin forest and selective-cutting forest accounted for 60.3%, 2.0%, and 37.7%, and 66.1%, 2.0%, and 31.2%, respectively. No significant differences were observed in the total NPP and the contribution rate of each component between the two forests. However, the ratios of the needle and broadleaf NPPs of the virgin and selective-cutting forests were 47.24:52.76 and 20.48:79.52, respectively, with a significant difference. The results indicated that the carbon density and NPP of the broadleaved-Korean pine forest after 34 years selective-cutting recovered to the levels of the virgin broadleaved-Korean pine forest.

Hydraulic architecture and tracheid allometry in mature Pinus palustris and Pinus elliottii trees.

PubMed

Gonzalez-Benecke, C A; Martin, T A; Peter, G F

2010-03-01

Pinus palustris Mill. (longleaf pine, LL) and Pinus elliottii Engelm. var. elliottii (slash pine, SL) frequently co-occur in lower coastal plain flatwoods of the USA, with LL typically inhabiting slightly higher and better-drained microsites than SL. The hydraulic architecture and tracheid dimensions of roots, trunk and branches of mature LL and SL trees were compared to understand their role in species microsite occupation. Root xylem had higher sapwood-specific hydraulic conductivity (k(s)) and was less resistant to cavitation compared with branches and trunk sapwood. Root k(s) of LL was significantly higher than SL, whereas branch and trunk k(s) did not differ between species. No differences in vulnerability to cavitation were observed in any of the organs between species. Across all organs, there was a significant but weak trade-off between water conduction efficiency and safety. Tracheid hydraulic diameter (D(h)) was strongly correlated with k(s) across all organs, explaining >73% of the variation in k(s). In contrast, tracheid length (L(t)) explained only 2.4% of the variability. Nevertheless, for trunk xylem, k(s) was 39.5% higher at 20 m compared with 1.8 m; this increase in k(s) was uncorrelated with D(h) and cell-wall thickness but was strongly correlated with the difference in L(t). Tracheid allometry markedly changed between sapwood of roots, trunks and branches, possibly reflecting different mechanical constraints. Even though vulnerability to cavitation was not different for sapwood of roots, branches or the trunks of LL and SL, higher sapwood to leaf area ratio and higher maximum sapwood-specific hydraulic conductivity in roots of LL are functional traits that may provide LL with a competitive advantage on drier soil microsites.

Modeling Tree Mortality Following Wildfire in Pinus ponderosa Forests in the Central Sierra Nevada of California

Treesearch

Jon C. Regelbrugge

1993-01-01

Abstract. We modeled tree mortality occurring two years following wildfire in Pinus ponderosa forests using data from 1275 trees in 25 stands burned during the 1987 Stanislaus Complex fires. We used logistic regression analysis to develop models relating the probability of wildfire-induced mortality with tree size and fire severity for Pinus ponderosa, Calocedrus...

Effect of Cutting Tool Properties and Depth of Cut in Rock Cutting: An Experimental Study

NASA Astrophysics Data System (ADS)

Rostamsowlat, Iman

2018-06-01

The current paper is designed to investigate the effect of worn (blunt) polycrystalline diamond compact cutter properties on both the contact stress (σ) and friction coefficient ( μ) mobilized at the wear flat-rock interface at different inclination angles of the wear flat surface and at a wide range of depths of cut. An extensive and comprehensive set of cutting experiments is carried out on two sedimentary rocks (one limestone and one sandstone) using a state-of-the-art rock cutting equipment (Wombat) and various blunt cutters. Experiments with blunt cutters are characterized by different wear flat inclination angles (β), different wear flat surface roughness (Ra), different wear flat material, and different cutting tool velocities ({\\varvec{v}}) were conducted. The experimental results show that both the contact stress and friction coefficient are predominantly affected by the wear flat roughness at all inclination angles of the wear flat; however, the cutting tool velocity has a negligible influence on both the contact stress and friction coefficient. Further investigations suggest that the contact stress is greatly affected by the depth of cut within the plastic regime of frictional contact while the contact stress is insensitive to the depth of cut within the elastic regime.

Temperature sensitivity of drought-induced tree mortality portends increased regional die-off under global-change-type drought

PubMed Central

Adams, Henry D.; Guardiola-Claramonte, Maite; Barron-Gafford, Greg A.; Villegas, Juan Camilo; Breshears, David D.; Zou, Chris B.; Troch, Peter A.; Huxman, Travis E.

2009-01-01

Large-scale biogeographical shifts in vegetation are predicted in response to the altered precipitation and temperature regimes associated with global climate change. Vegetation shifts have profound ecological impacts and are an important climate-ecosystem feedback through their alteration of carbon, water, and energy exchanges of the land surface. Of particular concern is the potential for warmer temperatures to compound the effects of increasingly severe droughts by triggering widespread vegetation shifts via woody plant mortality. The sensitivity of tree mortality to temperature is dependent on which of 2 non-mutually-exclusive mechanisms predominates—temperature-sensitive carbon starvation in response to a period of protracted water stress or temperature-insensitive sudden hydraulic failure under extreme water stress (cavitation). Here we show that experimentally induced warmer temperatures (≈4 °C) shortened the time to drought-induced mortality in Pinus edulis (piñon shortened pine) trees by nearly a third, with temperature-dependent differences in cumulative respiration costs implicating carbon starvation as the primary mechanism of mortality. Extrapolating this temperature effect to the historic frequency of water deficit in the southwestern United States predicts a 5-fold increase in the frequency of regional-scale tree die-off events for this species due to temperature alone. Projected increases in drought frequency due to changes in precipitation and increases in stress from biotic agents (e.g., bark beetles) would further exacerbate mortality. Our results demonstrate the mechanism by which warmer temperatures have exacerbated recent regional die-off events and background mortality rates. Because of pervasive projected increases in temperature, our results portend widespread increases in the extent and frequency of vegetation die-off. PMID:19365070

Maternal lineages of Pinus densata, a diploid hybrid.

PubMed

Song, Bao-Hua; Wang, Xiao-Quan; Wang, Xiao-Ru; Sun, Lan-Ju; Hong, De-Yuan; Peng, Pei-Hao

2002-06-01

Previous morphological, allozyme and chloroplast DNA data have suggested that Pinus densata originated through hybridization between P. tabuliformis and P. yunnanensis. In the present study, sequence and restriction site analyses of maternally inherited mitochondrial nad1 intron were used to detect variation patterns in 19 populations of P. tabuliformis, P. yunnanensis and P. densata. A total of three mitotypes (A, B, C) were detected. All but one of the populations of P. yunnanensis possessed mitotype B while all populations of P. tabuliformis had mitotype A. Pinus densata populations, on the other hand, harboured both mitotypes A and B, which are characteristic of P. tabuliformis and P. yunnanensis, respectively. This result gives strong additional evidence supporting the hybrid origin of this diploid pine. The distribution of mitotypes indicated very different mating compositions and evolutionary history among P. densata populations. It seems that local founder populations and backcrosses may have played important roles in the early establishment of P. densata populations. The uplift of the Tibetan Plateau had a significant impact on the distribution of maternal lineages of P. densata populations.

Impact of solar activity on growth of pine trees (Pinus cembra: 1610 - 1970; Pinus pinaster: 1910 -1989)

NASA Astrophysics Data System (ADS)

Surový, P.; Dorotovič, I.; Karlovský, V.; Rodrigues, J. C.; Rybanský, M.; Fleischer, P.

2010-12-01

In this work we have focused on the analysis of the data on the annual growth of cembra pine (Pinus cembra) grown in the Kôprová dolina Valley in the High Tatra Mountains. The database covers the period of 1406 - 1970, however, the sunspot data (minima and maxima) at the NGDC web site are only available since 1610. Moreover, reliable sunspot data are only available since 1749. The results of this analysis agree with the observation made in our previous work, i.e. there is a negative impact of high SA on the pine tree growth. However, it should be noted that statistical significance of the results is low. We also applied wavelet analysis to the data on the tree growth evolution, with the results indicating growth variations' period of about 20 years (duration of approximately two solar cycles or one magnetic cycle, respectively). A negative impact of the SA was also observed in growth of a 90 year-old maritime pine tree (Pinus pinaster) grown in northern Portugal. The width of the annual rings was smaller in the years of maximum SA; furthermore, it was found that it is the latewood growth that it is affected while the earlywood growth is not, and consequently the latewood additions also show a significative negative correlation with SA.

Newly developed primers for complete YCF1 amplification in Pinus (Pinaceae) chloroplasts with possible family-wide utility

Treesearch

Matthew Parks; Aaron Liston; Rich Cronn

2011-01-01

Primers were designed to amplify the highly variable locus ycf1 from all 11 subsections of Pinus to facilitate plastome assemblies based on short sequence reads as well as future phylogenetic and population genetic analyses. Primer design was based on alignment of 33 Pinus and four Pinaceae plastomes with...

Impacts of prescribed fire on Pinus rigida Mill

Treesearch

Nicholas J. Carlo; Heidi J. Renninger; Kenneth L. Clark; Karina V.R. Schäfer

2016-01-01

A comparative analysis of the impacts of prescribed fire on three upland forest stands in the Northeastern Atlantic Plain, NJ, USA, was conducted. Effects of prescribed fire on water use and gas exchange of overstory pines were estimated via sap-flux rates and photosynthetic measurements on Pinus rigida Mill. Each study site had two sap-flux plots...

Intraspecific variation in himalayan white pine, Pinus griffithii

Treesearch

John B. Genys

1977-01-01

Twenty-one seed sources of Himalayan white pine (Pinus griffithii McClel.) (11 from native stands and 10 from planted trees) were studied in Maryland's State Forest Tree Nursery and in 11 plantations in Maine, Maryland, Michigan, Illinois and North Carolina. In the nursery, intraspecific variations were observed in leaf lengths, time of bud-set, tendency for...

Recovery of Collembola in Pinus tabulaeformis plantations

Treesearch

Liang CHANG; Baifeng WANG; Xianghui LIU; Mac A. CALLAHAM; Feng GE

2017-01-01

Large areas of forest plantations have been developed in China. It is important to evaluate the soil fauna in plantations and the conditions needed for their recovery in view of the large areas of plantations in China. Three Pinus tabulaeformis forests, a 26-year-old plantation (P26) and a 45-year-old plantation (P45), exposed to clear-...

Herausforderungen durch die deutsche Wiedervereinigung

NASA Astrophysics Data System (ADS)

Stäglin, Reiner

Die Wiedervereinigung stellte auch die Statistik vor große Aufgaben. Die als Organ der staatlichen Planung staatsnah orientierte Statistik der DDR musste auf das zur Neutralität und wissenschaftlichen Unabhängigkeit verpflichtete System der Bundesrepublik umgestellt werden. Ebenso verlangten die Universitäten eine Neuorientierung. Die Deutsche Statistische Gesellschaft hat sich vor allem dreier Aufgaben mit großem Engagement, aber auch mit Bedachtsamkeit angenommen: Aufnahme und Integration der Statistiker aus den neuen Bundesländern in die Gesellschaft, Begleitung der Neuausrichtung des Faches Statistik an deren Hochschulen und Sicherung sowie Nutzung von Datenbeständen der ehemaligen DDR.

Genetic diversity and the mating system of a rare Mexican Piñon, Pinus pinceana, and a comparison with Pinus maximartinezii (Pinaceae)

Treesearch

F. Thomas Ledig; Miguel A. Capó-Arteaga; Paul D. Hodgskiss; Hassan Sbay; Celestino Flores-López; M. Thompson Conkle; Basilio Bermejo-Velázquez

2001-01-01

Weeping piñon (Pinus pinceana) has a restricted and fragmented range, trees are widely scattered within populations, and reproduction is limited. Nevertheless, genetic diversity was high; based on 27 isozyme loci in 18 enzyme systems, unbiased expected heterozygosity averaged 0.174. Differentiation also was high (FST = 0.152),...

Root architecture and wind-firmness of mature Pinus pinaster.

PubMed

Danjon, Frédéric; Fourcaud, Thierry; Bert, Didier

2005-11-01

This study aims to link three-dimensional coarse root architecture to tree stability in mature timber trees with an average of 1-m rooting depth. Undamaged and uprooted trees were sampled in a stand damaged by a storm. Root architecture was measured by three-dimensional (3-D) digitizing. The distribution of root volume by root type and in wind-oriented sectors was analysed. Mature Pinus pinaster root systems were organized in a rigid 'cage' composed of a taproot, the zone of rapid taper of horizontal surface roots and numerous sinkers and deep roots, imprisoning a large mass of soil and guyed by long horizontal surface roots. Key compartments for stability exhibited strong selective leeward or windward reinforcement. Uprooted trees showed a lower cage volume, a larger proportion of oblique and intermediate depth horizontal roots and less wind-oriented root reinforcement. Pinus pinaster stability on moderately deep soils is optimized through a typical rooting pattern and a considerable structural adaptation to the prevailing wind and soil profile.

Improvement of cutting performance for thick stainless steel plates by step-like cutting speed increase in high-power fiber laser cutting

NASA Astrophysics Data System (ADS)

Seon, Sangwoo; Shin, Jae Sung; Oh, Seong Yong; Park, Hyunmin; Chung, Chin-Man; Kim, Taek-Soo; Lee, Lim; Lee, Jonghwan

2018-07-01

A study was conducted to improve the cutting performance of a 60-mm thick stainless steel plate using a 6-kW fiber laser. Two techniques for improving the initial cutting performance were evaluated by preheating the work piece with a waiting time and step-like cutting speed increase. Both techniques showed improved cutting results compared to constant speed cutting. Among them, the method with a step-like cutting speed increase showed the better result in terms of cutting performance. As a result, a 60-mm thick stainless steel plate was cut at a maximum cutting speed of 72 mm/min with a preheating cutting speed of 24 mm/min. In order to confirm the effect of preheating, an additional experiment was performed to measure the temperature variation during the cutting process. Through this experiment, preheating temperature conditions were found to allow the specimen to be cut. It is expected that the results of this work will contribute to improving the cutting performance of thick metal structures in various industrial fields, as well as the dismantling of nuclear facilities using lasers in the future.

A holistic approach to genetic conservation of Pinus strobiformis

Treesearch

K.M. Waring; R. Sniezko; B.A. Goodrich; C. Wehenkel; J.J. Jacobs

2017-01-01

Pinus strobiformis (southwestern white pine) is threatened by both a rapidly changing climate and the tree disease white pine blister rust, caused by an introduced fungal pathogen, Cronartium ribicola. We began a proactive program in ~2009 to sustain P. strobiformis that includes genetic conservation, research, and management strategies. Research...

Aboveground tree biomass for Pinus ponderosa in northeastern California

Treesearch

Martin W. Ritchie; Jianwei Zhang; Todd A. Hamilton

2013-01-01

Forest managers need accurate biomass equations to plan thinning for fuel reduction or energy production. Estimates of carbon sequestration also rely upon such equations. The current allometric equations for ponderosa pine (Pinus ponderosa) commonly employed for California forests were developed elsewhere, and are often applied without consideration potential for...

Setup of a Parameterized FE Model for the Die Roll Prediction in Fine Blanking using Artificial Neural Networks

NASA Astrophysics Data System (ADS)

Stanke, J.; Trauth, D.; Feuerhack, A.; Klocke, F.

2017-09-01

Die roll is a morphological feature of fine blanked sheared edges. The die roll reduces the functional part of the sheared edge. To compensate for the die roll thicker sheet metal strips and secondary machining must be used. However, in order to avoid this, the influence of various fine blanking process parameters on the die roll has been experimentally and numerically studied, but there is still a lack of knowledge on the effects of some factors and especially factor interactions on the die roll. Recent changes in the field of artificial intelligence motivate the hybrid use of the finite element method and artificial neural networks to account for these non-considered parameters. Therefore, a set of simulations using a validated finite element model of fine blanking is firstly used to train an artificial neural network. Then the artificial neural network is trained with thousands of experimental trials. Thus, the objective of this contribution is to develop an artificial neural network that reliably predicts the die roll. Therefore, in this contribution, the setup of a fully parameterized 2D FE model is presented that will be used for batch training of an artificial neural network. The FE model enables an automatic variation of the edge radii of blank punch and die plate, the counter and blank holder force, the sheet metal thickness and part diameter, V-ring height and position, cutting velocity as well as material parameters covered by the Hensel-Spittel model for 16MnCr5 (1.7131, AISI/SAE 5115). The FE model is validated using experimental trails. The results of this contribution is a FE model suitable to perform 9.623 simulations and to pass the simulated die roll width and height automatically to an artificial neural network.

Displaced capillary dies

DOEpatents

Kalejs, Juris P.; Chalmers, Bruce; Surek, Thomas

1982-01-01

An asymmetrical shaped capillary die made exclusively of graphite is used to grow silicon ribbon which is capable of being made into solar cells that are more efficient than cells produced from ribbon made using a symmetrically shaped die.

Displaced capillary dies

DOEpatents

Kalejs, Juris P.; Chalmers, Bruce; Surek, Thomas

1984-01-01

An asymmetrical shaped capillary die made exclusively of graphite is used to grow silicon ribbon which is capable of being made into solar cells that are more efficient than cells produced from ribbon made using a symmetrically shaped die.

Portable cutting apparatus

DOEpatents

Gilmore, Richard F.

1986-01-01

A remotely operable, portable cutting apparatus detachably secured to the workpiece by laterally spaced clamp assemblies engageable with the workpiece on opposite sides of the intended line of cut. A reciprocal cutter head is mounted between the clamp assemblies and is provided with a traveling abrasive cutting wire adapted to sever the workpiece normal to the longitudinal axis thereof. Dust and debris are withdrawn from the cutting area by a vacuum force through a nozzle mounted on the cutting head.

Portable cutting apparatus

DOEpatents

Gilmore, R.F.

1984-07-17

A remotely operable, portable cutting apparatus detachably secured to the workpiece by laterally spaced clamp assemblies engagable with the workpiece on opposite sides of the intended line of cut. A reciprocal cutter head is mounted between the clamp assemblies and is provided with a traveling abrasive cutting wire adapted to sever the workpiece normal to the longitudinal axis thereof. Dust and debris are withdrawn from the cutting area by a vacuum force through a nozzle mounted on the cutting head.

Portable cutting apparatus

DOEpatents

Gilmore, Richard F.

1986-04-01

A remotely operable, portable cutting apparatus detachably secured to the workpiece by laterally spaced clamp assemblies engageable with the workpiece on opposite sides of the intended line of cut. A reciprocal cutter head is mounted between the clamp assemblies and is provided with a traveling abrasive cutting wire adapted to sever the workpiece normal to the longitudinal axis thereof. Dust and debris are withdrawn from the cutting area by a vacuum force through a nozzle mounted on the cutting head.

Phytochemical analysis of Pinus eldarica bark

PubMed Central

Iravani, S.; Zolfaghari, B.

2014-01-01

Bark extract of Pinus pinaster contains numerous phenolic compounds such as catechins, taxifolin, and phenolic acids. These compounds have received considerable attentions because of their anti-inflammatory, antimutagenic, anticarcinogenic, antimetastatic and high antioxidant activities. Although P. pinaster bark has been intensely investigated in the past; there is comparably less information available in the literature in regard to P. eldarica bark. Therefore, the aim of this study was to determine the chemical composition of P. eldarica commonly found in Iran. A reversed-phase high pressure liquid chromatography (RP-HPLC) method for the determination of catechin, caffeic acid, ferulic acid, and taxifolin in P. pinaster and P. eldarica was developed. A mixture of 0.1% formic acid in deionized water and 0.1% formic acid in acetonitrile was used as the mobile phase, and chromatographic separation was achieved on a Nova pack C18 at 280 nm. The two studied Pinus species contained high amounts of polyphenolic compounds. Among four marker compounds, the main substances identified in P. pinaster and P. eldarica were taxifolin and catechin, respectively. Furthermore, the composition of the bark oil of P. eldarica obtained by hydrodistillation was analyzed by gas chromatography/mass spectroscopy (GC/MS). Thirty-three compounds accounting for 95.1 % of the oil were identified. The oils consisted mainly of mono- and sesquiterpenoid fractions, especially α-pinene (24.6%), caryophyllene oxide (14.0%), δ-3-carene (10.7%), (E)-β-caryophyllene (7.9%), and myrtenal (3.1%). PMID:25657795

Early performance of Pinus contorta x banksiana hybrids

Treesearch

James E. Lotan

1967-01-01

Four Pinus contorta X banksiana hybrids developed in California were planted on two sites in Montana and one site in Idaho to determine whether they were suited to climate and soils of these three test locations and whether they were superior to Montana lodgepole pine. Height, diameter, crown width, number of branches per whorl, vigor, and survival were measured 5 and...

Wissenschaft, die unsere Kultur verändert. Tiefenschichten des Streits um die Evolutionstheorie

NASA Astrophysics Data System (ADS)

Patzelt, Werner J.

Die Evolutionstheorie ist eine der erfolgreichsten wissenschaftlichen Theorien. Sie erlaubt es, unsere Herkunft zu verstehen und riskante Merkmale gerade der menschlichen Spezies zu begreifen. Zugleich ist die Evolutionstheorie eine der umstrittensten Theorien. Das liegt nicht an ihrer empirischen Tragfähigkeit, sondern an ihrem Gegenstand. Sie handelt nämlich nicht nur - wie Hunderte andere wissenschaftliche Theorien - von der "Welt da draußen“, sondern vor allem auch von uns selbst und von unserem Platz in dieser Welt. Den einen gilt sie obendrein als Überwinderin religiösen Aberglaubens, den anderen als neuer Zugang zu Gott und seinem Wirken in der Welt. Ferner sehen die einen in der Evolution eine unbezweifelbare Tatsache gleich der Schwerkraft oder dem Holocaust, die anderen aber eine - noch oder dauerhaft - unbewiesene Hypothese oder gar eine falsche Schöpfungslehre. Und während die meisten Streitfragen solcher Art nach wechselseitig akzeptierten Regeln ‚normaler Wissenschaft‘ geklärt werden, wird bei der Frage nach dem Woher unserer Spezies und Kultur die intellektuelle Zuständigkeit von Wissenschaft mitunter überhaupt bezweifelt. Anscheinend geht es schon um recht tiefe Schichten unserer Kultur und nicht nur der wissenschaftlichen, wenn - wie seit 150 Jahren - um die Evolutionstheorie gestritten wird. Wie sehen diese Schichten aus?

The Ambiguous Dying Syndrome

ERIC Educational Resources Information Center

Bern-Klug, Mercedes

2004-01-01

More than one-half of the 2.4 million deaths that will occur in the United States in 2004 will be immediately preceded by a time in which the likelihood of dying can best be described as "ambiguous." Many people die without ever being considered "dying" or "at the end of life." These people may miss out on the…

The Angry Dying Patient.

PubMed

Houston, Robert E.

1999-02-01

Over 25 years ago, Kubler-Ross identified anger as a predictable part of the dying process. When the dying patient becomes angry in the clinical setting, all types of communication become strained. Physicians can help the angry dying patient through this difficult time by using 10 rules of engagement. When physicians engage and empathize with these patients, they improve the patient's response to pain and they reduce patient suffering. When physicians educate patients on their normal responses to dying and enlist them in the process of family reconciliation, they can impact the end-of-life experience in a positive way.

The Angry Dying Patient

PubMed Central

Houston, Robert E.

1999-01-01

Over 25 years ago, Kubler-Ross identified anger as a predictable part of the dying process. When the dying patient becomes angry in the clinical setting, all types of communication become strained. Physicians can help the angry dying patient through this difficult time by using 10 rules of engagement. When physicians engage and empathize with these patients, they improve the patient's response to pain and they reduce patient suffering. When physicians educate patients on their normal responses to dying and enlist them in the process of family reconciliation, they can impact the end-of-life experience in a positive way. PMID:15014699

Levels and sources of PAHs in selected sites from Portugal: biomonitoring with Pinus pinea and Pinus pinaster needles.

PubMed

Ratola, Nuno; Amigo, José Manuel; Alves, Arminda

2010-04-01

Pine needle samples from two pine species (Pinus pinaster Ait. and Pinus pinea L.) were collected at 29 sites scattered throughout Portugal, in order to biomonitor the levels and trends of 16 polycyclic aromatic hydrocarbons (PAHs). The values obtained for the sum of all PAHs ranged from 76 to 1944 ng/g [dry weight (dw)]. Despite the apparent matrix similarities between both pine species, P. pinaster needles revealed higher mean entrapment levels than P. pinea (748 and 399 ng/g (dw) per site, respectively). The urban and industrial sites have the highest average of PAH incidence [for P. pinea, 465 and 433 ng/g (dw) per site, respectively, and for P. pinaster, 1147 and 915 ng/g (dw)], followed by the rural sites [233 ng/g and 711 ng/g (dw) per site, for P. pinea and P. pinaster, respectively]. The remote sites, both from P. pinaster needles, show the least contamination, with 77 ng/g (dw) per site. A predominance of 3-ring and 4-ring PAHs was observed in most samples, with phenanthrene having 30.1% of the total. Naphthalene prevailed in remote sites. Rainfall had no influence on the PAHs levels, but there was a relationship between higher wind speeds and lower concentrations. PAH molecular ratios revealed the influence of both petrogenic and pyrogenic sources.

Resilience and vulnerability: prolonged grief in the bereaved spouses of marital partners who died of AIDS.

PubMed

Yu, Nancy Xiaonan; Chan, Cecilia L W; Zhang, Jianxin; Stewart, Sunita M

2016-01-01

Spousal bereavement is closely linked to prolonged grief, that is, significant adjustment symptoms that last for more than six months after the loss. This article focused on potential risk and protective factors that may influence bereavement outcomes. Participants in this study were surviving spouses of individuals who died of acquired immune deficiency syndrome (AIDS). These participants were themselves living with human immunodeficiency syndrome. In this cross-sectional study, 120 bereaved participants completed measures of grief, quality of dying and death of the deceased, negative conceptions of death resulting from AIDS, death attitudes, and personal resilience. The results showed that one-third (35.0%) of the bereaved participants reported grief levels above the prolonged grief cut-off scores, and can be categorized as the "prolonged grief" group. Although quality of dying and death was not associated with the intensity of grief, negative conceptions of death from AIDS, fear of death and resilience independently predicted grief symptoms in the regression models. Our findings provide insight into the grief process for the surviving spouse of AIDS victims in rural China. Since resilience is malleable, developing resilience interventions to enhance adjustment to bereavement may be a promising direction in grief counselling and therapies.

Energy Saving Melting and Revert Reduction Technology (E-SMARRT): Development of Surface Engineered Coating Systems for Aluminum Pressure Die Casting Dies: Towards a 'Smart' Die Coating

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dr. John J. Moore; Dr. Jianliang Lin,

2012-07-31

The main objective of this research program was to design and develop an optimal coating system that extends die life by minimizing premature die failure. In high-pressure aluminum die-casting, the die, core pins and inserts must withstand severe processing conditions. Many of the dies and tools in the industry are being coated to improve wear-resistance and decrease down-time for maintenance. However, thermal fatigue in metal itself can still be a major problem, especially since it often leads to catastrophic failure (i.e. die breakage) as opposed to a wear-based failure (parts begin to go out of tolerance). Tooling costs remain themore » largest portion of production costs for many of these parts, so the ability prevent catastrophic failures would be transformative for the manufacturing industry.The technology offers energy savings through reduced energy use in the die casting process from several factors, including increased life of the tools and dies, reuse of the dies and die components, reduction/elimination of lubricants, and reduced machine down time, and reduction of Al solder sticking on the die. The use of the optimized die coating system will also reduce environmental wastes and scrap parts. Current (2012) annual energy saving estimates, based on initial dissemination to the casting industry in 2010 and market penetration of 80% by 2020, is 3.1 trillion BTU's/year. The average annual estimate of CO2 reduction per year through 2020 is 0.63 Million Metric Tons of Carbon Equivalent (MM TCE).« less

Natural mycorrhizal colonization of pines on reclaimed surface mines in Virginia. [Pinus strobus; Pinus taeda; Pinus virginiana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schoenholtz, S.H.; Burger, J.A.; Torbert, J.L.

The effects of spoil type, slow-release fertilization, and weed control using glyphosate on the degree of ectomycorrhizal colonization of container-grown white (Pinus strobus L.), loblolly (P. taeda L.), and Virginia (P. virginiana Mill.) pines were studied on two strip mined sites (sandstone vs. siltstone overburden material) in southwestern Virginia. Although some seedlings were successfully colonized at both sites, the number of seedlings colonized and the proportion of short-root colonization per seedling were consistently higher on the sandstone spoil. On both sites, loblolly and Virginia pines had more ectomycorrhizal formation than white pine. Foliar P levels of all three species onmore » the sandstone spoil and of loblolly pine on the siltstone spoil were significantly correlated with ectomycorrhizal development. The degree of ectomycorrhizal formation for any of the species on either spoil was not decreased by slow-release fertilization or glyphosate applications. These results indicate that natural mycorrhizal colonization is compatible with these cultural treatments, and that colonization from indigenous fungal species may be adequate, eliminating the need for artificial inoculation.« less

Relative size and stand age determine Pinus banksiana mortality

Treesearch

Han Y. H. Chen; Songling Fu; Robert A. Monserud; Ian C. Gillies

2008-01-01

Tree mortality is a poorly understood process in the boreal forest. Whereas large disturbances reset succession by killing all or most trees, background tree mortality was hypothesized to be affected by competition, ageing, and stand composition. We tested these hypotheses on jack pine (Pinus banksiana Lamb.) mortality using data from long-term...

Neighbour-die effect on the measurement of wafer-level flip-chip LED dies in production lines

NASA Astrophysics Data System (ADS)

Chen, Tengfei; Wan, Zirui; Li, Bin

2017-11-01

The light from the side surfaces of the test flip-chip light-emitting diode (FCLED) dies is reflected, refracted or absorbed by neighbour dies during the measurement of wafer-level FCLED dies in production lines. A notable measurement deviation is caused by the neighbour-die effect, which is not considered in current industry practice. In this paper, Monte Carlo ray-tracing simulations are used to study the measurement deviations caused by the neighbour-die effect and extension ratios of the film. The simulation results show that the maximal deviation of radiant flux impinging the photodiode can reach 5.5%, if the die is tested without any neighbour dies, or is surrounded by a set of neighbour dies at an extension ratio of 1.1. Moreover, the dependence between the measurement results and neighbour cases for different extension ratios is also investigated. Then, a modified calibration method is proposed and studied. The proposed technique can be used to improve the calibration and measurement accuracy of the test equipment used for measurement of wafer-level FCLED dies in production lines.

[Acceleration of Embryonic Development of Pinus sibirica Trees with a One-Year Reproductive Cycle].

PubMed

Tret'yakova, I N; Lukina, N V

2016-01-01

The study of the formation of embryonic structures in Pinus sibirica forms with a one-year reproductive cycle showed that the acceleration of the embryonic process manifested itself as a reduction of the coenocytic stage of the female gametophyte development (1.5 months instead of 1 year). The egg was not fertilized because of the asynchronous maturation of male and female gametophytes. Seeds without embryos were formed. We assumed that the acceleration of the reproductive process in Pinus sibirica was caused by a mutation in the female generative organs.

Pinus lambertiana Dougl. Sugar Pine; Pinaceae Pine family

Treesearch

Bohun B. Kinloch Jr.; William H. Scheuner

1990-01-01

Called "the most princely of the genus" by its discoverer, David Douglas, sugar pine (Pinus lambertiana) is the tallest and largest of all pines, commonly reaching heights of 53 to 61 m (175 to 200 ft) and d.b.h. of 91 to 152 cm (36 to 60 in). Old trees occasionally exceed 500 years and, among associated species, are second only to giant...

Extrusion die and method

DOEpatents

Lipp, G. Daniel

1994-04-26

A method and die apparatus for manufacturing a honeycomb body of rhombic cell cross-section by extrusion through an extrusion die of triangular cell discharge slot configuration, the die incorporating feedholes at selected slot intersections only, such that slot segments communicating directly with the feedholes discharge web material and slot segments not so connected do not discharge web material, whereby a rhombic cell cross-section in the extruded body is provided.

Cutting roller

DOE Office of Scientific and Technical Information (OSTI.GOV)

Best, G.; Weikert, N.B.

1984-05-29

A cutting roller for a mining machine, having a substantially conical closure member arranged to face the workings and a tubular body member which has a larger diameter at the end nearer the face working face than at the discharge end. The tubular member carries at least one cutting blade, and the closure member mounts at least one cutting blade; each blade is provided at its edge region with a plurality of bit holders for the attachment of cutter bits. The outer surface of the body member merges into the substantially conical closure member in a smooth, even curve, somore » that the outside diameter of the body member in the region of the working face is substantially greater than the diameter in the region of the discharge end of the cutting roller. The roller is provided with liquid distribution channels on each cutting blade, which channels are connected to a single liquid distribution ring channel in the region of the substantially conical closure member.« less

Pest risk assessment of the importation into the United States of unprocessed Pinus logs and chips from Australia

Treesearch

John T Kliejunas; Harold H. Burdsall; Gregg A. DeNitto; Andris Eglitis; Dennis A. Haugen; Michael I. Haverty; Jessie A. Micales-Glaeser

2006-01-01

The unmitigated pest risk potential for the importation of unprocessed logs and chips of species of Pinus (Pinus radiata, P. elliottii Engelm. var. elliottii, P. taeda L., and P. caribaea var. hondurensis, principally) from Australia into the United States was assessed by estimating the likelihood and consequences of introduction of representative insects and pathogens...

Bishop pine (Pinus muricata) of inland Marin County, CA

Treesearch

Constance I. Millar

1986-01-01

The locations and characteristics of five, small, previously undescribed stands of bishop pine (Pinus muricata) in central Marin Co., California, are reported. Three stands lie on dry sites in the Kent Lake Drainage north of Mt. Tamalpais: San Geronimo Ridge, a spur ridge above Little Carson Cr., and Oat Hill. These stands are anomalous in occurring...

Portable propellant cutting assembly, and method of cutting propellant with assembly

NASA Technical Reports Server (NTRS)

Sharp, Roger A. (Inventor); Hoskins, Shawn W. (Inventor); Payne, Brett D. (Inventor)

2002-01-01

A propellant cutting assembly and method of using the assembly to cut samples of solid propellant in a repeatable and consistent manner is disclosed. The cutting assembly utilizes two parallel extension beams which are shorter than the diameter of a central bore of an annular solid propellant grain and can be loaded into the central bore. The assembly is equipped with retaining heads at its respective ends and an adjustment mechanism to position and wedge the assembly within the central bore. One end of the assembly is equipped with a cutting blade apparatus which can be extended beyond the end of the extension beams to cut into the solid propellant.

Salmonellosis in passerine birds in Maryland and West Virginia

USGS Publications Warehouse

Locke, L.N.; Shillinger, R.B.; Jareed, T.

1973-01-01

Salmonella typhimurium was responsible for a die-off of evening grosbeaks (Hesperiphona vespertina) at Elkins, West Virginia, and was isolated from a pine siskin (Spinus pinus) collected at the site of a die-off near Baltimore, Maryland.

Psychotherapy with Older Dying Persons.

ERIC Educational Resources Information Center

Dye, Carol J.

Psychotherapy with older dying patients can lead to problems of countertransference for the clinician. Working with dying patients requires flexibility to adapt basic therapeutics to the institutional setting. Goals of psychotherapy must be reconceptualized for dying clients. The problems of countertransference arise because clinicians themselves…

Pest risk assessment of the importation into the United States of unprocessed Pinus and Abies logs from Mexico

Treesearch

B. M. Tkacz; H. H. Burdsall; G. A. DeNitto; A. Eglitis; J. B. Hanson; J. T. Kliejunas; W. E. Wallner; J. G. O`Brien; E. L. Smith

1998-01-01

The unmitigated pest risk potential for the importation of Pinus and Abies logs from all states of Mexico into the United States was assessed by estimating the probability and consequences of establishment of representative insects and pathogens of concern. Twenty-two individual pest risk assessments were prepared for Pinus logs, twelve dealing with insects and ten...

Slash disposal and seedbed preparation by tractor

Treesearch

Donald T. Gordon

1956-01-01

Creating ground conditions favorable to regeneration immediately after the final harvest cutting is basic to forest management wherever advance growth is deficient. Ponderosa (Pinus ponderosa Laws) and Jeffrey pine (Pinus jeffreyi Grev. & Balf.) seeds require bare mineral soil for satisfactory germination. Pine seedlings,...

Understory plant biomass dynamics of prescribed burned Pinus palustris stands

Treesearch

C.A. Gonzalez-Benecke; L.J. Samuelson; T.A. Stokes; W.P. Cropper Jr; T.A. Martin; K.H. Johnsen

2015-01-01

Longleaf pine (Pinus palustris Mill.) forests are characterized by unusually high understory plant species diversity, but models describing understory ground cover biomass, and hence fuel load dynamics, are scarce for this fire-dependent ecosystem. Only coarse scale estimates, being restricted on accuracy and geographical extrapolation,...

Pultrusion Die Assembly

NASA Technical Reports Server (NTRS)

Wilson, Maywood L. (Inventor); Johnson, Gary S. (Inventor); Frye, Mark W. (Inventor); Stanfield, Clarence E. (Inventor)

1988-01-01

This invention relates generally to pultrusion die assemblies, and more particularly, to a pultrusion die assembly which incorporates a plurality of functions in order to produce a continuous, thin composite fiber reinforced thermoplastic material. The invention is useful for making high performance thermoplastic composite materials in sheets which can be coiled on a spool and stored for further processing.

Hydraulic redistribution of water from Pinus ponderosa trees to seedlings: evidence for an ectomycorrhizal pathway.

PubMed

Warren, Jeffrey M; Brooks, J Renée; Meinzer, Frederick C; Eberhart, Joyce L

2008-01-01

While there is strong evidence for hydraulic redistribution (HR) of soil water by trees, it is not known if common mycorrhizal networks (CMN) can facilitate HR from mature trees to seedlings under field conditions. Ponderosa pine (Pinus ponderosa) seedlings were planted into root-excluding 61-microm mesh barrier chambers buried in an old-growth pine forest. After 2 yr, several mature trees were cut and water enriched in D(2)O and acid fuchsin dye was applied to the stumps. Fine roots and mycorrhizal root tips of source trees became heavily dyed, indicating reverse sap flow in root xylem transported water from stems throughout root systems to the root hyphal mantle that interfaces with CMN. Within 3 d, D(2)O was found in mesh-chamber seedling foliage > 1 m from source trees; after 3 wk, eight of 10 mesh-chamber seedling stem samples were significantly enriched above background levels. Average mesh-chamber enrichment was 1.8 x greater than that for two seedlings for which the connections to CMN were broken by trenching before D(2)O application. Even small amounts of water provided to mycorrhizas by HR may maintain hyphal viability and facilitate nutrient uptake under drying conditions, which may provide an advantage to seedlings hydraulically linked by CMN to large trees.

Cutting assembly

DOEpatents

Racki, Daniel J.; Swenson, Clark E.; Bencloski, William A.; Wineman, Arthur L.

1984-01-01

A cutting apparatus includes a support table mounted for movement toward and away from a workpiece and carrying a mirror which directs a cutting laser beam onto the workpiece. A carrier is rotatably and pivotally mounted on the support table between the mirror and workpiece and supports a conduit discharging gas toward the point of impingement of the laser beam on the workpiece. Means are provided for rotating the carrier relative to the support table to place the gas discharging conduit in the proper positions for cuts made in different directions on the workpiece.

Influence of soil porosity on water use in Pinus taeda

Treesearch

G. Hacke; J.S. Sperry; B.E. Ewers; D.S. Ellsworth; K.V.R. Schäfer; R. Oren

2000-01-01

We analyzed the hydraulic constraints imposed on water uptake from soils of different porosities in loblolly pine (Pinus taeda L.) by comparing genetically related and even-aged plantations growing in loam versus sand soil. Water use was evaluated relative to the maximum transpiration rate (Ecrit) allowed by the soil-leaf...

Characteristics, histories, and future succession of northern Pinus pugens stands

Treesearch

Patrick Brose

2017-01-01

Pinus pungens (Table Mountain pine) stands are rare conifer-dominated communities that occur on xeric ridges and upper slopes throughout the central and southern Appalachian Mountains. At the northern end of this range, this uncommon forest community is essentially unstudied. Therefore, in 2006 I initiated a dendroecology study of three ...

[Isolation and identification of diterpenoids from Pinus koraiensis].

PubMed

Yang, Xin; Zhang, Ying-chun; Zhang, Hua; Wang, Jing

2008-01-01

To study chemical compounds from Pinus koraiensis. The constituents were isolated by chromatographic method and the structures were identified on the basis of spectral alanlysis. Eight compounds were identified as 8 (14)-podocarpen-13-on-18-oic acid (1), 15-hydroxydehydroabietic acid (2), 12-hydroxyabietic acid (3), lambertianic acid (4), dehydroabietic acid (5), sandaracopimaric acid (6), beta-sitosterol (7), daucosterol (8). Compounds 1--6 are isolated from this plant for the first time.

Cutting thread at flexible endoscopy.

PubMed

Gong, F; Swain, P; Kadirkamanathan, S; Hepworth, C; Laufer, J; Shelton, J; Mills, T

1996-12-01

New thread-cutting techniques were developed for use at flexible endoscopy. A guillotine was designed to follow and cut thread at the endoscope tip. A new method was developed for guiding suture cutters. Efficacy of Nd: YAG laser cutting of threads was studied. Experimental and clinical experience with thread-cutting methods is presented. A 2.4 mm diameter flexible thread-cutting guillotine was constructed featuring two lateral holes with sharp edges through which sutures to be cut are passed. Standard suture cutters were guided by backloading thread through the cutters extracorporeally. A snare cutter was constructed to retrieve objects sewn to tissue. Efficacy and speed of Nd: YAG laser in cutting twelve different threads were studied. The guillotine cut thread faster (p < 0.05) than standard suture cutters. Backloading thread shortened time taken to cut thread (p < 0.001) compared with free-hand cutting. Nd: YAG laser was ineffective in cutting uncolored threads and slower than mechanical cutters. Results of thread cutting in clinical studies using sewing machine (n = 77 cutting episodes in 21 patients), in-vivo experiments (n = 156), and postsurgical cases (n = 15 over 15 years) are presented. New thread-cutting methods are described and their efficacy demonstrated in experimental and clinical studies.

Hybridization and classification of the white pines (Pinus section strobus)

Treesearch

William B. Critchfield

1986-01-01

Many North American and Eurasian white pines retain their ability to hybridize even after long isolation, and about half of all white pine hybrids from controlled pollinations are inter-hemisphere crosses. Within the morphologically homogeneous and otherwise highly crossable core group of white pines, an exception in crossing behavior is Pinus lambertiana...

Impact of the eocene on the evolution of Pinus L.

Treesearch

Constance I. Millar

1993-01-01

Pinus evolved in middle latitudes of the Northern Hemisphere in the middle Mesozoic. By the late Cretaceous pines had spread east and west throughout Laurasia, attaining high diversity in eastern Asia, the eastern United States, and western Europe, but having little representation at high northern latitudes. Changing climates in the early Tertiary...

Pinus ponderosa: geographic races and subspecies based on morphological variation

Treesearch

Robert Z. Callaham

2013-01-01

Morphological variation of ponderosa pine (Pinus ponderosa Dougl. ex Laws.), growing north of Mexico, is described. A map shows distributions of five putative races that are analyzed and discussed. Characteristics of branches, shoots, and needles were measured for 10 or fewer trees growing on 147 plots located at 1,500-ft elevational intervals...

Enhanced drought-tolerance in the homoploid hybrid species Pinus densata: implication for its habitat divergence from two progenitors.

PubMed

Ma, Fei; Zhao, Changming; Milne, Richard; Ji, Mingfei; Chen, Litong; Liu, Jianquan

2010-01-01

The homoploid hybrid species Pinus densata is restricted to alpine habitats that exceed the altitude range of its two parental species, Pinus tabulaeformis and Pinus yunnanensis. Alpine habitats usually generate cold-induced water stress in plants. To understand the ecological differentiation between these three species, we examined their physiological responses to drought stress. Potted seedlings of three species were subjected to low, mild, moderate and severe water stress in an automatic-controlled glasshouse. Fifteen indicators of fitness were measured for each species in each treatment, and most of these decreased as drought increased. Pinus densata exhibited higher fitness than both parental species in terms of total dry mass production (TDM) and long-term water use efficiency (WUE(L)) across all treatments; several other ecophysiological traits were also extreme but not across every treatment, and not always in the highest stress treatment. These results indicate that extreme characters that have become well fixed in P. densata, confer a faster seedling growth rate and more efficient water use, which in turn should confer increased drought tolerance. These traits of P. densata likely promoted its ecological separation from its parental species and facilitated its successful colonization and establishment in high-altitude habitats.

[Studies on chemical constituents of Pinus armandii].

PubMed

Yang, Xin; Ding, Yi; Sun, Zhi-hao; Zhang, Dong-ming

2005-05-01

To study chemical constituents from pine cone of Pinus armandii Franch. The constituents were isolated by chromatographic method and the structures were identified on the basis of spectral analysis. Four compounds were identified as 7-oxo-12alpha, 13beta-dihydroxyabiet-8(14)-en18-oic acid (I), 7-oxo-13beta-hydroxyabiet-8 (14)-en-18-oic acid (II), 8 (14)-podocarpen-13-on-18-oic acid (III) and lambertianic acid (IV). Compound I is a new diterpenoid and compounds II, III were isolated from this plant for the first time.

Fundamentals of cutting.

PubMed

Williams, J G; Patel, Y

2016-06-06

The process of cutting is analysed in fracture mechanics terms with a view to quantifying the various parameters involved. The model used is that of orthogonal cutting with a wedge removing a layer of material or chip. The behaviour of the chip is governed by its thickness and for large radii of curvature the chip is elastic and smooth cutting occurs. For smaller thicknesses, there is a transition, first to plastic bending and then to plastic shear for small thicknesses and smooth chips are formed. The governing parameters are tool geometry, which is principally the wedge angle, and the material properties of elastic modulus, yield stress and fracture toughness. Friction can also be important. It is demonstrated that the cutting process may be quantified via these parameters, which could be useful in the study of cutting in biology.

On the Cutting Performance of Segmented Diamond Blades when Dry-Cutting Concrete

PubMed Central

Martynenko, V.; Martínez Krahmer, D.; Benítez, A.; Genovese, G.

2018-01-01

The objective of the present study is to analyze and compare the cutting performance of segmented diamond blades when dry-cutting concrete. A cutting criteria is proposed to characterize the wear of the blades by measuring the variation of the external diameter and the weight loss of the blade. The results exhibit the cutting blade SB-A, which has twice the density of diamonds and large contact area, exhibits less wear even though the material removal rate is higher compared with the other two cutting blades. Additionally, the surface topography of the different blades is evaluated to examine the impact of wear depending on the surface profile and the distribution of the diamonds in the blade’s matrix. Large number of diamonds pull-out are found in blades type SB-C, which additionally shows the worst wear resistant capability. As a conclusion, the cutting efficiency of the blade is found to be related to the density of embedded diamonds and the type of the surface profile of the cutting blade after reaching the stop criteria. PMID:29425125

On the Cutting Performance of Segmented Diamond Blades when Dry-Cutting Concrete.

PubMed

Sánchez Egea, A J; Martynenko, V; Martínez Krahmer, D; López de Lacalle, L N; Benítez, A; Genovese, G

2018-02-09

The objective of the present study is to analyze and compare the cutting performance of segmented diamond blades when dry-cutting concrete. A cutting criteria is proposed to characterize the wear of the blades by measuring the variation of the external diameter and the weight loss of the blade. The results exhibit the cutting blade SB-A, which has twice the density of diamonds and large contact area, exhibits less wear even though the material removal rate is higher compared with the other two cutting blades. Additionally, the surface topography of the different blades is evaluated to examine the impact of wear depending on the surface profile and the distribution of the diamonds in the blade's matrix. Large number of diamonds pull-out are found in blades type SB-C, which additionally shows the worst wear resistant capability. As a conclusion, the cutting efficiency of the blade is found to be related to the density of embedded diamonds and the type of the surface profile of the cutting blade after reaching the stop criteria.

Laser cutting of Kevlar laminates and thermal stress formed at cutting sections

NASA Astrophysics Data System (ADS)

Yilbas, B. S.; Akhtar, S. S.

2012-02-01

Laser cutting of Kevlar laminates is carried out and thermal stress field developed in the cutting region is predicted using the finite element code. Temperature predictions are validated through the thermocouple data. The morphological changes in the cutting section are examined by incorporating optical and scanning electron microscopes. It is found that temperature predictions agree well with the thermocouple data. High values of von Mises stress are observed at the cutting edges and at the mid-thickness of the Kevlar laminate due to thermal compression formed in this region. The laser cut edges are free from whiskers; however, striation formation and some small sideways burning is observed at the kerf edges.

X-Z-Theta cutting method

DOEpatents

Bieg, Lothar F.

1993-01-12

A method for machining a workpiece. The method includes the use of a rotary cutting tool mounted on the end of a movable arm. The arm is adapted to move in a plane perpendicular to the axis of rotation of the cutting tool. The cutting tool has cutting teeth to cut chips of material off of the workpiece in a predetermined size and shape to facilitate better removal of the chips from the workpiece. The teeth can be of different type and length to permit the tool to both rough cut and finish cut the workpiece during machining. The total depth of cut is divided by the number of tool teeth, so that the longest tool always performs the finishing cut.

Medizintechnik in der Tumororthopädie

NASA Astrophysics Data System (ADS)

Burgkart, Rainer; Gollwitzer, Hans; Holzapfel, Boris; Rudert, Maximilian; Rechl, Hans; Gradinger, Reiner

Die Behandlung der Knochentumoren unterlag in den letzten 20 Jahren einem raschen und stetigen Wandel, was zum einen auf die verbesserten Therapieerfolge durch den Einsatz von neoadjuvanten Therapieformen zurückzuführen ist, und andererseits von medizintechnischen Entwicklungen bezüglich moderner Schnittbilddiagnostik, neuer 3D Operationsplanungsverfahren wie das Rapid Prototyping und adaptiv modularer Tumorendoprothesensystemen u. a. begleitet wurde. Gerade die technischen Entwicklungen haben dazu geführt, daß im Bereich der Extremitäten und der Wirbelsäule radikalere Eingriffe durchgeführt werden können, was die lokale Tumorkontrolle wesentlich verbessert hat. In zunehmenden Maße werden deshalb nicht nur Kurzzeiterfolge sondern auch mittel- und langfristige Fortschritte bei der Behandlung der malignen Knochentumoren einschließlich der Metastasenbehandlung erreicht. Grundlage der Therapie ist dabei immer primär die Sicherung der Diagnose mittels Biopsie und die bildgebende sowie histologische Stadieneinteilung des malignen Tumors. Nach der Tumorresektion kann die Rekonstruktion biologisch oder mit Endoprothesensystemen erfolgen. Gerade die weiterentwickelten modularen Systeme führen zu guten funktionellen Ergebnissen mit langen Standzeiten und einer reduzierten Komplikationsrate. Individuell angefertigte Implantate sind vor allem im Bereich der Rekonstruktion komplexer Beckentumoren von großer klinischer Bedeutung.

Missing and dark rings associated with drought in Pinus halepensis

Treesearch

Klemen Novak; Martin De Luis; Jozica Gricar; Peter Prislan; Maks Merela; Kevin T. Smith; Katarina Cufar

2016-01-01

The responses of the vascular cambium and tracheid differentiation to extreme drought in Aleppo pine (Pinus halepensis Mill.) were investigated. The research focused on the drought year of 2005, in the primary study area at Maigmo (MAI) in southeastern Spain, with comparisons in Jarafuel (JAL) and Guardamar (GUA). The climate in this region is...

Whitebark pine (Pinus albicaulis) in Cascadia: A climate change prognosis

Treesearch

Sierra C. McLane

2011-01-01

Species distribution models (SDMs) predict that whitebark pine (Pinus albicaulis) will lose much of its current climatic range in Cascadia (the Pacific Northwest in the United States plus British Columbia, Canada) by the 2080s as the climate warms. However, the same models indicate that the species will simultaneously gain a large, climatically-favorable habitat...

Effects of Arceuthobium americanum on twig growth of Pinus contorts.

Treesearch

Nancy Broshot; Lynn Larsen; Robert. Tinnin

1986-01-01

Patterns of branch growth in Pinus contorta Dougl. ex Loud, (lodgepole pine) on the east side of the Cascade Range in Oregon were significantly altered by Arceuthobium americanum (lodgepole pine dwarf mistletoe). There were decreases in the number, length, and mass of needles, as well as in the length and mass of twigs. These...

A range-wide restoration strategy for whitebark pine (Pinus albicaulis)

Treesearch

Robert E. Keane; D. F. Tomback; C. A. Aubry; A. D. Bower; E. M. Campbell; C. L. Cripps; M. B. Jenkins; M. F. Mahalovich; M. Manning; S. T. McKinney; M. P. Murray; D. L. Perkins; D. P. Reinhart; C. Ryan; A. W. Schoettle; C. M. Smith

2012-01-01

Whitebark pine (Pinus albicaulis), an important component of western high-elevation forests, has been declining in both the United States and Canada since the early Twentieth Century from the combined effects of mountain pine beetle (Dendroctonus ponderosae) outbreaks, fire exclusion policies, and the spread of the exotic disease white pine blister rust (caused by the...

Vacuum die attach for integrated circuits

DOEpatents

Schmitt, Edward H.; Tuckerman, David B.

1991-01-01

A thin film eutectic bond for attaching an integrated circuit die to a circuit substrate is formed by coating at least one bonding surface on the die and substrate with an alloying metal, assembling the die and substrate under compression loading, and heating the assembly to an alloying temperature in a vacuum. A very thin bond, 10 microns or less, which is substantially void free, is produced. These bonds have high reliability, good heat and electrical conduction, and high temperature tolerance. The bonds are formed in a vacuum chamber, using a positioning and loading fixture to compression load the die, and an IR lamp or other heat source. For bonding a silicon die to a silicon substrate, a gold silicon alloy bond is used. Multiple dies can be bonded simultaneously. No scrubbing is required.

Device for cutting protrusions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bzorgi, Fariborz M

An apparatus for clipping a protrusion of material is provided. The protrusion may, for example, be a bolt head, a nut, a rivet, a weld bead, or a temporary assembly alignment tab protruding from a substrate surface of assembled components. The apparatus typically includes a cleaver having a cleaving edge and a cutting blade having a cutting edge. Generally, a mounting structure configured to confine the cleaver and the cutting blade and permit a range of relative movement between the cleaving edge and the cutting edge is provided. Also typically included is a power device coupled to the cutting blade.more » The power device is configured to move the cutting edge toward the cleaving edge. In some embodiments the power device is activated by a momentary switch. A retraction device is also generally provided, where the retraction device is configured to move the cutting edge away from the cleaving edge.« less

Growth and Site Relationships of Pinus caribaea Across the Caribbean Basin

Treesearch

Leon H. Liegel; [Compiler

1991-01-01

Summarizes results of growth, volume, basal area, and stand conditions for Pinus caribaea var. hondurensis in five countries. Past pine management practices are reviewed for all countries. Implications of new forestry and soils research are discussed in terms of their impact on future local reforestation and afforestation...

Multi-Season Monoterpene and Sesquiterpene Analysis of Pinus taeda Needle Tissue

EPA Science Inventory

Pinus taeda (Loblolly pine) is one of the worlds most important timber crop and accounts for a significant portion of the southeastern U.S. landcover. Biogenic voltile organic compound (BVOC) content was extracted from the tissue material of P. taeda needles and analyzed over a m...

Experimental Investigation on Cutting Characteristics in Nanometric Plunge-Cutting of BK7 and Fused Silica Glasses

PubMed Central

An, Qinglong; Ming, Weiwei; Chen, Ming

2015-01-01

Ductile cutting are most widely used in fabricating high-quality optical glass components to achieve crack-free surfaces. For ultra-precision machining of brittle glass materials, critical undeformed chip thickness (CUCT) commonly plays a pivotal role in determining the transition point from ductile cutting to brittle cutting. In this research, cutting characteristics in nanometric cutting of BK7 and fused silica glasses, including machined surface morphology, surface roughness, cutting force and specific cutting energy, were investigated with nanometric plunge-cutting experiments. The same cutting speed of 300 mm/min was used in the experiments with single-crystal diamond tool. CUCT was determined according to the mentioned cutting characteristics. The results revealed that 320 nm was found as the CUCT in BK7 cutting and 50 nm was determined as the size effect of undeformed chip thickness. A high-quality machined surface could be obtained with the undeformed chip thickness between 50 and 320 nm at ductile cutting stage. Moreover, no CUCT was identified in fused silica cutting with the current cutting conditions, and brittle-fracture mechanism was confirmed as the predominant chip-separation mode throughout the nanometric cutting operation. PMID:28788010

Experimental Investigation on Cutting Characteristics in Nanometric Plunge-Cutting of BK7 and Fused Silica Glasses.

PubMed

An, Qinglong; Ming, Weiwei; Chen, Ming

2015-03-27

Ductile cutting are most widely used in fabricating high-quality optical glass components to achieve crack-free surfaces. For ultra-precision machining of brittle glass materials, critical undeformed chip thickness (CUCT) commonly plays a pivotal role in determining the transition point from ductile cutting to brittle cutting. In this research, cutting characteristics in nanometric cutting of BK7 and fused silica glasses, including machined surface morphology, surface roughness, cutting force and specific cutting energy, were investigated with nanometric plunge-cutting experiments. The same cutting speed of 300 mm/min was used in the experiments with single-crystal diamond tool. CUCT was determined according to the mentioned cutting characteristics. The results revealed that 320 nm was found as the CUCT in BK7 cutting and 50 nm was determined as the size effect of undeformed chip thickness. A high-quality machined surface could be obtained with the undeformed chip thickness between 50 and 320 nm at ductile cutting stage. Moreover, no CUCT was identified in fused silica cutting with the current cutting conditions, and brittle-fracture mechanism was confirmed as the predominant chip-separation mode throughout the nanometric cutting operation.

The effects of fepeated prescribed burning on Pinus ponderosa growth

Treesearch

David L. Peterson; Stephen S. Sackett; Lindsay J. Robinson; Sally M. Haase

1994-01-01

The effect of repeated prescribed burning on long term growth of Pinus ponderosa in northern Arizona was examined. Fire treatments for hazard reduction were initiated in 1976,and growthwas evaluated in 1988 for fire rotations of 1, 2, 4, 6, 8, and 10 years. Dendroecological analysis shows that there were only small changes in treegrowth (compared tocontrols) in the...

[Dying and death in societal transformation].

PubMed

Heller, Andreas; Wegleitner, Klaus

2017-01-01

Dying and death in modern societies are subject to profound social, professional and cultural-religious changes. Secularization and a stronger differentiation of societies have led to a change in the way humans handle the dying process. Normatively ritualized collective behaviour has been replaced by an individual, subjectivized approach. In late modern societies there are many different views of what "successful" or "good" dying means.In the article this change is described by the following seven theses: 1. We live longer and we die longer. 2. We no longer die suddenly and unexpectedly but slowly and foreseeably. 3. Even though our biological life on earth has become longer, our life has been shortened by the loss of eternity. 4. We no longer die on the stage of ritualized relationships with our family and neighbours but behind the curtains of organizations. 5. We live and die in a society of organizations and have to get organized for the final phase of our life. 6. Living and dying are no large, state-owned enterprises but small, private enterprises. 7. The hospice movement as well as palliative medicine have created public awareness, made dying a matter of discussion and offered a new set of options.In late modernism end-of-life care requires new approaches based on individual and shared responsibility as well as cooperation between professional institutions and community-based voluntary care.A change towards community care is visible. Thus "dying" is a topic in the discussion about the future of public health and societal solidarity.

Apparatus for restraining and transporting dies

DOEpatents

Allison, James W.; LaBarre, Timothy L.

1994-01-01

Apparatus for restraining and transporting dies in punch press operations is provided. A floatation platen for supporting a die on the platen's upper surface has a plurality of recessed gas exhaust ports on the platen's lower surface. A source of pressurized gas delivers gas to a platen manifold, for delivery to orifices located in the gas exhaust ports. The flow of gas is controlled by a first valve adjacent the gas source and a second valve adjacent the manifold, with the second valve being used to control the gas flow during movement of the die. In this fashion, a die may be moved on a cushion of air from one workstation to a selected second workstation. A moveable hydraulically operated restraining fixture is also provided, for clamping the die in position during the compacting phase, and for releasing the die after completion of the compacting phase by releasing the hydraulic pressure on the restraining fixture. When pressure in the hydraulic cylinders on the restraining fixture is reversed, the restraining fixture will retract so that there is no contact between the die and the restraining fixture, thereby allowing the die to be removed from a first workstation and moved to a second selected workstation.

Vacuum die attach for integrated circuits

DOEpatents

Schmitt, E.H.; Tuckerman, D.B.

1991-09-10

A thin film eutectic bond for attaching an integrated circuit die to a circuit substrate is formed by coating at least one bonding surface on the die and substrate with an alloying metal, assembling the die and substrate under compression loading, and heating the assembly to an alloying temperature in a vacuum. A very thin bond, 10 microns or less, which is substantially void free, is produced. These bonds have high reliability, good heat and electrical conduction, and high temperature tolerance. The bonds are formed in a vacuum chamber, using a positioning and loading fixture to compression load the die, and an IR lamp or other heat source. For bonding a silicon die to a silicon substrate, a gold silicon alloy bond is used. Multiple dies can be bonded simultaneously. No scrubbing is required. 1 figure.

Reinraumtechnik für die Medizintechnik

NASA Astrophysics Data System (ADS)

Petek, Max; Jungbluth, Martin; Krampe, Erhard

Die Reinraumtechnik ist heute ein unverzichtbarer Bestandteil bei der Fertigung von Produkten der Life Sciences, den Bereichen Pharma, Lebensmittel, Kosmetik und Medizintechnik. In Anbetracht der langen Historie der Medizintechnik ist sie jedoch eine sehr junge Disziplin. Die Bedeutung von Keimen und die richtige Einschätzung ihrer Größe wurden zwar sehr früh bereits durch Paracelsus erkannt, jedoch wurden daraus noch keine speziellen oder kontinuierlich umgesetzten Hygienevorschriften abgeleitet. Die erste bekannte technische Umsetzung von Hygieneempfehlungen geht auf den Franzosen François Nicolas Appert zurück, der eine aseptische Abfüllmethode für Lebensmittel entwickelte und diese 1810 veröffentlichte [1]. Die erste dokumentierte medizinische Umsetzung stellten Hygienevorschriften für Ärzte dar, die Ignaz Philipp Semmelweis nach 1847 in der Wiener Klinik für Geburtshilfe einführte [2].

Responses of Wound-Inoculated Seedlings of Pinus elliottii var. elliottii and Pinus taeda to Mycelial Cultures Derived from Multople and Singel Basidiospores of Cronartium quercuum f. sp. fusiforme

Treesearch

T. Miller; K.P. Gramacho; R.A. Schmidt; H.V. Amerson; E.G. Kuhlman

1998-01-01

In 1991, a series of experiments was initiated to examine the effectiveness and research value of inoculating 6-week-old seedlings of slash (Pinus elliottii var. elliottii) and loblolly pine (P. raeda) with suspensions of basidiospores of Cronartium quercuum f. sp. fusiforme...

Managing succession in conifer plantations: converting young red pine (Pinus resinosa Ait.) plantations to native forest types by thinning and underplantiing

Treesearch

William C. Parker; Ken A. Elliott; Daniel C. Dey; Eric Boysen; Steven G. Newmaster

2001-01-01

The effects of thinning on growth and survival of white pine (Pinus strobus L.), white ash (Fraxinus americana L.), and red oak (Quercus rubra L.), and understory plant diversity were examined in a young red pine (Pinus resinosa Ait.) plantation. Five years after thinning, seedling diameter,...

An FMS Dynamic Production Scheduling Algorithm Considering Cutting Tool Failure and Cutting Tool Life

NASA Astrophysics Data System (ADS)

Setiawan, A.; Wangsaputra, R.; Martawirya, Y. Y.; Halim, A. H.

2016-02-01

This paper deals with Flexible Manufacturing System (FMS) production rescheduling due to unavailability of cutting tools caused either of cutting tool failure or life time limit. The FMS consists of parallel identical machines integrated with an automatic material handling system and it runs fully automatically. Each machine has a same cutting tool configuration that consists of different geometrical cutting tool types on each tool magazine. The job usually takes two stages. Each stage has sequential operations allocated to machines considering the cutting tool life. In the real situation, the cutting tool can fail before the cutting tool life is reached. The objective in this paper is to develop a dynamic scheduling algorithm when a cutting tool is broken during unmanned and a rescheduling needed. The algorithm consists of four steps. The first step is generating initial schedule, the second step is determination the cutting tool failure time, the third step is determination of system status at cutting tool failure time and the fourth step is the rescheduling for unfinished jobs. The approaches to solve the problem are complete-reactive scheduling and robust-proactive scheduling. The new schedules result differences starting time and completion time of each operations from the initial schedule.

Contoured Orifice for Silicon-Ribbon Die

NASA Technical Reports Server (NTRS)

Mackintosh, B. H.

1985-01-01

Die configuration encourages purity and stable growth. Contour of die orifice changes near ribbon edges. As result, silicon ribbon has nearly constant width and little carbon contamination. Die part of furnace being developed to produce high-quality, low-cost material for solar cells.

CAE Based Die Face Engineering Development to Contribute to the Revitalization of the Tool & Die Industry

NASA Astrophysics Data System (ADS)

Tang, Arthur; Lee, Wing C.; St. Pierre, Shawn; He, Jeanne; Liu, Kesu; Chen, Chin C.

2005-08-01

Over the past two decades, the Computer Aided Engineering (CAE) tools have emerged as one of the most important engineering tools in various industries, due to its flexibility and accuracy in prediction. Nowadays, CAE tools are widely used in the sheet metal forming industry to predict the forming feasibility of a wide variety of complex components, ranging from aerospace and automotive components to household products. As the demand of CAE based formability accelerates, the need for a robust and streamlined die face engineering tool becomes more crucial, especially in the early stage when the tooling layout is not available, but a product design decision must be made. Ability to generate blank, binder and addendum surfaces with an appropriate layout of Drawbead, Punch Opening Line, Trim Line are the primary features and functions of a CAE based die face engineering tool. Once the die face layout is ready, a formability study should be followed to verify the die face layout is adequate to produce a formable part. If successful, the established die face surface should be exported back to the CAD/CAM environment to speed up the tooling and manufacturing design process with confidence that this particular part is formable with this given die face. With a CAE tool as described above, the tool & die industry will be greatly impacted as the processes will enable the bypass of hardware try-out and shorten the overall vehicle production timing. The trend has shown that OEMs and first tiers will source to low cost producers in the world which will have a negative impact to the traditional tool & die makers in the developed countries. CAE based tool as described should be adopted, along with many other solutions, in order to maintain efficiency of producing high quality product and meeting time-to-market requirements. This paper will describe how a CAE based die face engineering (DFE) tool could be further developed to enable the traditional tool & die makers to meet the

First discovery of fossil winged seeds of Pinus L. (family Pinaceae) from the Indian Cenozoic and its palaeobiogeographic significance

NASA Astrophysics Data System (ADS)

Khan, Mahasin Ali; Bera, Subir

2017-07-01

The occurrences of Pinus L. (family Pinaceae) megafossils (cones and leaf remains) have been abundantly documented from the Cenozoic sediments of eastern Asia (Japan and China), but none has been confirmed from the Indian Cenozoic till date. Here, we describe Pinus arunachalensis Khan and Bera, sp. nov. on the basis of seed remains from the middle to late Miocene Siwalik sediments of the Dafla Formation exposed around West Kameng district in Arunachal Pradesh, eastern Himalaya. Seeds are winged, broadly oblong to oval in outline, 1.3-1.5 cm long and 0.4-0.6 cm broad (in the middle part), located basipetally and symmetrically to wing, cellular pattern of wing is seemingly undulatory and parallel with the long axis of the wing. So far, this report provides the first ever fossil record of Pinus winged seeds from India. This record suggests that Pinus was an important component of tropical-subtropical evergreen forest in the area during the Miocene and this group subsequently declined from the local vegetation probably because of the gradual intensification of MSI (monsoon index) from the Miocene to the present. We also review the historical phytogeography and highlight the phytogeographic implication of this genus.

Navigating "Assisted Dying".

PubMed

Schipper, Harvey

2016-02-01

Carter is a bellwether decision, an adjudication on a narrow point of law whose implications are vast across society, and whose impact may not be realized for years. Coupled with Quebec's Act Respecting End-of-life Care it has sharply changed the legal landscape with respect to actively ending a person's life. "Medically assisted dying" will be permitted under circumstances, and through processes, which have yet to be operationally defined. This decision carries with it moral assumptions, which mean that it will be difficult to reach a unifying consensus. For some, the decision and Act reflect a modern acknowledgement of individual autonomy. For others, allowing such acts is morally unspeakable. Having opened the Pandora's Box, the question becomes one of navigating a tolerable societal path. I believe it is possible to achieve a workable solution based on the core principle that "medically assisted dying" should be a very rarely employed last option, subject to transparent ongoing review, specifically as to why it was deemed necessary. My analysis is based on 1. The societal conditions in which have fostered demand for "assisted dying", 2. Actions in other jurisdictions, 3. Carter and Quebec Bill 52, 4. Political considerations, 5. Current medical practice. Leading to a series of recommendations regarding. 1. Legislation and regulation, 2. The role of professional regulatory agencies, 3. Medical professions education and practice, 4. Public education, 5. Health care delivery and palliative care. Given the burden of public opinion, and the legal steps already taken, a process for assisted-dying is required. However, those legal and regulatory steps should only be considered a necessary and defensive first step in a two stage process. The larger goal, the second step, is to drive the improvement of care, and thus minimize assisted-dying.

Climate-related genetic variation in a threatened tree species, Pinus albicaulis

Treesearch

Marcus V. Warwell; Ruth G. Shaw

2017-01-01

PREMISE OF THE STUDY: With ongoing climate change, understanding of intraspecific adaptive variation is critical for conservation and restoration of plant species. Such information is especially scarce for threatened and endangered tree species, such as Pinus albicaulis Engelm. Therefore, our principal aims were to assess adaptive variation and characterize its...

Assessing the gene content of the megagenome: sugar pine (Pinus lambertiana)

Treesearch

Daniel Gonzalez-Ibeas; Pedro J. Martinez-Garcia; Randi A. Famula; Annette Deflino-Mix; Kristian A. Stevens; Carol A. Loopstra; Charles H. Landley; David B. Neale; Jill L. Wegryzn

2016-01-01

Sugar pine (Pinus lambertiana Douglas) is within the subgenus Strobus with an estimated genome size of 31 Gbp. Transcriptomic resources are of particular interest in conifers due to the challenges presented in their megagenomes for gene identification. In this study, we present the first comprehensive survey of the P. lambertiana...

Western gall rust -- A threat to Pinus radiata in New Zealand

Treesearch

Tod D. Ramsfield; Darren J. Kriticos; Detlev R. Vogler; Brian W. Geils

2007-01-01

Western gall rust (Peridermium harknessii J. P. Moore (syn. Endocronartium harknessii (J. P. Moore) Y. Hiratsuka) is potentially a serious threat to exotic Pinus radiata D. Don plantations of New Zealand although the pathogen has not been recorded here. Mechanisms that may have prevented invasion of the pathogen include geographic...

Mechanical specific energy versus depth of cut in rock cutting and drilling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhou, Yaneng; Zhang, Wu; Gamwo, Isaac

The relationship between Mechanical Specific Energy (MSE) and the Rate of Penetration (ROP), or equivalently the depth of cut per revolution, provides an important measure for strategizing a drilling operation. This study explores how MSE evolves with depth of cut, and presents a concerted effort that encompasses analytical, computational and experimental approaches. A simple model for the relationship between MSE and cutting depth is first derived with consideration of the wear progression of a circular cutter. This is an extension of Detournay and Defourny's phenomenological cutting model. Wear is modeled as a flat contact area at the bottom of amore » cutter referred to as a wear flat, and that wear flat in the past is often considered to be fixed during cutting. But during a drilling operation by a full bit that consists of multiple circular cutters, the wear flat length may increase because of various wear mechanisms involved. The wear progression of cutters generally results in reduced efficiency with either increased MSE or decreased ROP. Also, an accurate estimate of removed rock volume is found important for the evaluation of MSE. The derived model is compared with experiment results from a single circular cutter, for cutting soft rock under ambient pressure with actual depth measured through a micrometer, and for cutting high strength rock under high pressure with actual cutting area measured by a confocal microscope. Lastly, the model is employed to interpret the evolution of MSE with depth of cut for a full drilling bit under confining pressure. The general form of equation of the developed model is found to describe well the experiment data and can be applied to interpret the drilling data for a full bit.« less

Mechanical specific energy versus depth of cut in rock cutting and drilling

DOE PAGES

Zhou, Yaneng; Zhang, Wu; Gamwo, Isaac; ...

2017-12-07

The relationship between Mechanical Specific Energy (MSE) and the Rate of Penetration (ROP), or equivalently the depth of cut per revolution, provides an important measure for strategizing a drilling operation. This study explores how MSE evolves with depth of cut, and presents a concerted effort that encompasses analytical, computational and experimental approaches. A simple model for the relationship between MSE and cutting depth is first derived with consideration of the wear progression of a circular cutter. This is an extension of Detournay and Defourny's phenomenological cutting model. Wear is modeled as a flat contact area at the bottom of amore » cutter referred to as a wear flat, and that wear flat in the past is often considered to be fixed during cutting. But during a drilling operation by a full bit that consists of multiple circular cutters, the wear flat length may increase because of various wear mechanisms involved. The wear progression of cutters generally results in reduced efficiency with either increased MSE or decreased ROP. Also, an accurate estimate of removed rock volume is found important for the evaluation of MSE. The derived model is compared with experiment results from a single circular cutter, for cutting soft rock under ambient pressure with actual depth measured through a micrometer, and for cutting high strength rock under high pressure with actual cutting area measured by a confocal microscope. Lastly, the model is employed to interpret the evolution of MSE with depth of cut for a full drilling bit under confining pressure. The general form of equation of the developed model is found to describe well the experiment data and can be applied to interpret the drilling data for a full bit.« less

L-connect routing of die surface pads to the die edge for stacking in a 3D array

DOEpatents

Petersen, Robert W.

2000-01-01

Integrated circuit chips and method of routing the interface pads from the face of the chip or die to one or more sidewall surfaces of the die. The interconnection is routed from the face of the die to one or more edges of the die, then routed over the edge of the die and onto the side surface. A new pad is then formed on the sidewall surface, which allows multiple die or chips to be stacked in a three-dimensional array, while enabling follow-on signal routing from the sidewall pads. The routing of the interconnects and formation of the sidewall pads can be carried out in an L-connect or L-shaped routing configuration, using a metalization process such as laser pantography.

Genic diversity, genetic structure, and biogeography of Pinus sabiniana Dougl.

Treesearch

F. Thomas Ledig

1999-01-01

Pinus sabiniana Dougl. (grey pine) forms savanna forests in the foothills surrounding California’s Great Central Valley. However, its fossil record, which dates from the late Miocene through the Pliocene and Pleistocene, is found exclusively in southern California, south of the species’ present range. A total of twenty-nine isozyme loci, representing eighteen enzyme...

Numerical simulations of fire spread in a Pinus pinaster needles fuel bed

NASA Astrophysics Data System (ADS)

Menage, D.; Chetehouna, K.; Mell, W.

2012-11-01

The main aim of this paper is to extend the cases of WFDS model validation by comparing its predictions to literature data on a ground fire spreading in a Pinus pinaster needles fuel bed. This comparison is based on the experimental results of Mendes-Lopes and co-workers. This study is performed using the same domain as in the experiments (3.0m×1.2m×0.9m) with a mesh of 49,280 cells. We investigate the influence of wind (varied between 0 and 2 m/s) and moisture content (10 and 18%) on the rate of spread. The WFDS rate of spread is determined using a cross-correlation function of ground temperature profiles. The simulated rate of spread, as well as temperature, compared favourably to experimental values and show the WFDS model capacity to predict ground fires in Pinus Pinaster fuel beds.

Improving Pathogen Reduction by Chlorine Wash Prior to Cutting in Fresh-Cut Processing

USDA-ARS?s Scientific Manuscript database

Introduction: Currently, most fresh-cut processing facilities in the United States use chlorinated water or other sanitizer solutions for microbial reduction after lettuce is cut. Freshly cut lettuce releases significant amounts of organic matter that negatively impacts the effectiveness of chlorine...

Transcriptome analysis of Pinus halepensis under drought stress and during recovery.

PubMed

Fox, Hagar; Doron-Faigenboim, Adi; Kelly, Gilor; Bourstein, Ronny; Attia, Ziv; Zhou, Jing; Moshe, Yosef; Moshelion, Menachem; David-Schwartz, Rakefet

2018-03-01

Forest trees use various strategies to cope with drought stress and these strategies involve complex molecular mechanisms. Pinus halepensis Miller (Aleppo pine) is found throughout the Mediterranean basin and is one of the most drought-tolerant pine species. In order to decipher the molecular mechanisms that P. halepensis uses to withstand drought, we performed large-scale physiological and transcriptome analyses. We selected a mature tree from a semi-arid area with suboptimal growth conditions for clonal propagation through cuttings. We then used a high-throughput experimental system to continuously monitor whole-plant transpiration rates, stomatal conductance and the vapor pressure deficit. The transcriptomes of plants were examined at six physiological stages: pre-stomatal response, partial stomatal closure, minimum transpiration, post-irrigation, partial recovery and full recovery. At each stage, data from plants exposed to the drought treatment were compared with data collected from well-irrigated control plants. A drought-stressed P. halepensis transcriptome was created using paired-end RNA-seq. In total, ~6000 differentially expressed, non-redundant transcripts were identified between drought-treated and control trees. Cluster analysis has revealed stress-induced down-regulation of transcripts related to photosynthesis, reactive oxygen species (ROS)-scavenging through the ascorbic acid (AsA)-glutathione cycle, fatty acid and cell wall biosynthesis, stomatal activity, and the biosynthesis of flavonoids and terpenoids. Up-regulated processes included chlorophyll degradation, ROS-scavenging through AsA-independent thiol-mediated pathways, abscisic acid response and accumulation of heat shock proteins, thaumatin and exordium. Recovery from drought induced strong transcription of retrotransposons, especially the retrovirus-related transposon Tnt1-94. The drought-related transcriptome illustrates this species' dynamic response to drought and recovery and unravels

Screening Pinus sylvestris grown for the production of Christmas trees for resistance to western gall rust Peridermium harknessii using different sources of aeciospores

Treesearch

Todd A. Burnes; Jennifer Juzwik; Robert A. Blanchette

1999-01-01

Results showed a moderate to high susceptibility of Pinus sylvestris to western gall rust Peridermium barknessii, from Pinna sylvestris in Michigan and Pinna banksiana in Minnesota. In general, Pinus sylvestris seed sources were more susceptible to aeciospores collected from...

Changes in plant species composition along an elevation gradient in an old-growth bottomland hardwood-Pinus taeda forest in southern Arkansas

Treesearch

Adrian G. Grell; Michael G. Shelton; Eric Heitzman

2005-01-01

Old-growth bottomland hardwood-Pinus taeda L. forests are rare in Arkansas, and the complex relationships between plant communities and environmental conditions have not been well described in these forests. To investigate these relationships, a digital elevation model was developed for a 16.2 ha old-growth bottomland hardwood-Pinus taeda forest in...

The Influence of Pinus brutia on the Water Balance of Fractured Mediterranean Mountain Environments

NASA Astrophysics Data System (ADS)

Eliades, Marinos; Bruggeman, Adriana; Lubczynski, Maciek; Christou, Andreas

2016-04-01

In dry Mediterranean environments, both rainfall and temperature vary throughout the year and frequent droughts occur. The mountainous topography is characterized by steep slopes, often leading to shallow soil layers with limited water storage capacity. While for most of the tree species, these conditions can be characterized as unfavourable, Pinus brutia trees manage to survive and thrive. The main objective of this study is to define and quantify the water balance components of a Pinus brutia forest at tree level. Our study was conducted from 30/12/2014 until 31/09/2015 in an 8966-m2 fenced area of Pinus brutia forest. The site is located on the northern foothills of Troodos mountain at 620 m elevation, in Cyprus. The slope of the site ranged between 0 and 82%. The average daily minimum temperature is 5 0C in January and the average daily maximum temperature is 35 oC in August. The mean annual rainfall is 425 mm. We measured the diameter at breast height (DBH) from a total of 122 trees. Based on the average DBH, four trees were selected for monitoring (two were above the average DBH and two were below). We measured soil depth in a 1-m grid around each of the four selected trees. We processed soil depths in ArcGIS software (ESRI) to create a soil depth map. We used a Total Station and a differential GPS for the creation of a high resolution DEM of the area covering the four selected trees. We installed soil moisture sensors at 15-cm depth at distances of 1 and 2 m from the selected trees and a second sensor at 30-cm depth when the soil was deeper than 20 cm.. We randomly installed four metric manual rain gauges under each trees' canopy to measure throughfall and for stemflow we installed a plastic tube around each tree trunk and connected it to a manual rain gauge. We used six sap flow heat ratio method instruments to determine sap flow rates of the Pinus brutia trees. Two trees had one sensor installed at 1.3 m height facing north. The remaining trees had two sap

Modeling and analysis of the chip formation and transient cutting force during elliptical vibration cutting process

NASA Astrophysics Data System (ADS)

Lin, Jieqiong; Guan, Liang; Lu, Mingming; Han, Jinguo; Kan, Yudi

2017-12-01

In traditional diamond cutting, the cutting force is usually large and it will affect tool life and machining quality. Elliptical vibration cutting (EVC) as one of the ultra-precision machining technologies has a lot of advantages, such as reduces cutting force, extend tool life and so on. It's difficult to predict the transient cutting force of EVC due to its unique elliptical motion trajectory. Study on chip formation will helpfully to predict cutting force. The geometric feature of chip has important effects on cutting force, however, few scholars have studied the chip formation. In order to investigate the time-varying cutting force of EVC, the geometric feature model of chip is established based on analysis of chip formation, and the effects of cutting parameters on the geometric feature of chip are analyzed. To predict transient force quickly and effectively, the geometric feature of chip is introduced into the cutting force model. The calculated results show that the error between the predicted cutting force in this paper and that in the literature is less than 2%, which proves its feasibility.

Extrusion die and method

DOEpatents

Lipp, G. Daniel

1994-05-03

A method and die apparatus for manufacturing a honeycomb body of triangular cell cross-section and high cell density, the die having a combination of (i) feedholes feeding slot intersections and (ii) feedholes feeding slot segments not supplied from slot intersections, whereby a reduction in feedhole count is achieved while still retaining good extrusion efficiency and extrudate uniformity.

Electrophoretic Analysis of Diversity and Phylogeny of Pinus brutia and Closely Related Taxa

Treesearch

M. T. Conkle; G. Schiller; C. Grunwald

1988-01-01

Rangewide samples from mature natural stands of Pinus brutia Ten. subsp. brutia, subsp. stankewiczii (Sukaczew) Nahal, subsp. pithyusa (Stevenson) Nahal, and subsp. eldarica (Medw.) Nahal from throughout the eastern Mediterranean display a continuum of allozyme variation for...

Potential carry-over of seeds from 11 common shrub and vine competitors of loblolly and shortleaf pines

Treesearch

Michael G. Shelton; Michael D. Cain

2002-01-01

Many of the competitors of the regeneration of loblolly and shortleaf pines (Pinus taeda, L. and Pinus echinata Mill., respectively) develop from seed disseminated on the site after reproduction cutting or from the seed bank. To evaluate the potential carry-over of the seeds from 11 shrub and vine competitors of these two...

Mortalidade em florestas de Pinus palustris causada por tempestade de raios

Treesearch

Kenneth W. Outcalt; Jorge Paladino Corrêa de Lima; Jose Américo de Mello Filho

2002-01-01

The importance of lightning as an ignition source for the fire driven Pinus palustris ecosystem is widely recognized. Lightning also impacts this system on a smaller scale by causing individual tree mortality. The objective of this study was to determine the level of mortality due to lightning activity at the Department of Energy's Savannah...

Two centuries of fire in a southwestern Virginia Pinus pungens community

Treesearch

E. K. Sutherland; H. Grissino-Mayer; C. A. Woodhouse; W. W. Covington; S. Horn; L. Huckaby; R. Kerr; J. Kush; M. Moore; T. Plumb

1995-01-01

Fire exclusion in fire-dependent forest communities can alter stand structure and composition. The objective was to construct a fire history of two Pinus pungens Lamb. communities growing in southwestern Virgina. Treering analysis of fire-scarred P. pungens specimens and a tree survey were used to determine species composition and age distributions. From 1798-1944,...

Differentiating suicide decedents who died using firearms from those who died using other methods.

PubMed

Anestis, Michael D; Khazem, Lauren R; Anestis, Joye C

2017-06-01

Studies have documented a link between gun ownership and suicide, but little is known about characteristics of those most likely to use a gun in a suicide attempt rather than alternative methods. We examined which factors differentiate suicide decedents who died using a gun from those who died by other methods. We further examined whether such findings are consistent within the subcomponent of our larger sample comprised entirely of gun owning suicide decedents. Data reflect 267 suicide decedents, with data provided by individuals who identified as having lost someone to suicide (loss survivors). Within the full sample, a higher proportion of gun-owning and male suicide decedents died by firearm. Further, individuals who had previously discussed suicide or engaged in one or more non-lethal suicide attempts were less likely to die by suicide using a gun. Within the subsample of gun owning suicide decedents, a greater proportion of decedents who stored guns at home and in unsecure locations died from self-inflected gunshot wounds. These findings add clarity to the relationship between firearm ownership and death by suicide at the individual level. Furthermore, these findings are consistent with the notion that means safety implementation may represent a vital suicide prevention tool. Copyright © 2017. Published by Elsevier B.V.

Effect of Cutting Velocity / Stem Size on the Efficiency of NRCRI Cassave Stem Cutting Machine

NASA Astrophysics Data System (ADS)

Ikejiofor, M. C.

2012-11-01

The developed NRCRI (National Root Crops Research Institute) cassava stem cutting machine was evaluated. The cassava stems from the variety TME 419 were used. The sizes of the stem used were 1.8, 2.0, 2.3 and 2.6cm. Also, different cutting velocities of 1.20, 1.23 and 1.32m/s were used. The stakes produced has length of 2.5cm. Analysis of variance in RCBD was used to evaluate the effect of the cutting velocity and the stem size on the efficiency of the cutting machine. The result of the analysis showed that the cutting velocity had very highly significant effect, while the stem size had no significant effect at 5% level on the efficiency of the cutting machine. The data obtained also showed that the highest and least cutting efficiencies of 99.42 and 94.71% were obtained with the machine cutting velocities of 1.2 and 1.32m/s respectively.

Energy Consumption of Die Casting Operations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jerald Brevick; clark Mount-Campbell; Carroll Mobley

2004-03-15

Molten metal processing is inherently energy intensive and roughly 25% of the cost of die-cast products can be traced to some form of energy consumption [1]. The obvious major energy requirements are for melting and holding molten alloy in preparation for casting. The proper selection and maintenance of melting and holding equipment are clearly important factors in minimizing energy consumption in die-casting operations [2]. In addition to energy consumption, furnace selection also influences metal loss due to oxidation, metal quality, and maintenance requirements. Other important factors influencing energy consumption in a die-casting facility include geographic location, alloy(s) cast, starting formmore » of alloy (solid or liquid), overall process flow, casting yield, scrap rate, cycle times, number of shifts per day, days of operation per month, type and size of die-casting form of alloy (solid or liquid), overall process flow, casting yield, scrap rate, cycle times, number of shifts per day, days of operation per month, type and size of die-casting machine, related equipment (robots, trim presses), and downstream processing (machining, plating, assembly, etc.). Each of these factors also may influence the casting quality and productivity of a die-casting enterprise. In a die-casting enterprise, decisions regarding these issues are made frequently and are based on a large number of factors. Therefore, it is not surprising that energy consumption can vary significantly from one die-casting enterprise to the next, and within a single enterprise as function of time.« less

Declarations on euthanasia and assisted dying.

PubMed

Inbadas, Hamilton; Zaman, Shahaduz; Whitelaw, Sandy; Clark, David

2017-10-01

Declarations on end-of-life issues are advocacy interventions that seek to influence policy, raise awareness and call others to action. Despite increasing prominence, they have attracted little attention from researchers. This study tracks the emergence, content, and purpose of declarations concerned with assisted dying and euthanasia, in the global context. The authors identified 62 assisted dying/euthanasia declarations covering 1974-2016 and analyzed them for originating organization, geographic scope, format, and stated viewpoint on assisted dying/euthanasia. The declarations emerged from diverse organizational settings and became more frequent over time. Most opposed assisted dying/euthanasia.

Declarations on euthanasia and assisted dying

PubMed Central

Inbadas, Hamilton; Zaman, Shahaduz; Whitelaw, Sandy; Clark, David

2017-01-01

ABSTRACT Declarations on end-of-life issues are advocacy interventions that seek to influence policy, raise awareness and call others to action. Despite increasing prominence, they have attracted little attention from researchers. This study tracks the emergence, content, and purpose of declarations concerned with assisted dying and euthanasia, in the global context. The authors identified 62 assisted dying/euthanasia declarations covering 1974–2016 and analyzed them for originating organization, geographic scope, format, and stated viewpoint on assisted dying/euthanasia. The declarations emerged from diverse organizational settings and became more frequent over time. Most opposed assisted dying/euthanasia. PMID:28398131

Inheritance of allozyme variants in bishop pine (Pinus muricata D.Don)

Treesearch

Constance I. Millar

1985-01-01

Isozyme phenotypes are described for 45 structural loci and I modifier locus in bishop pine (Pinus muricata D. Don,) and segregation data are presented for a subset of 31 polymorphic loci from 19 enzyme systems. All polymorphic loci had alleles that segregated within single-focus Mendelian expectations, although one pair of alleles at each of three...

Soil enzyme activities in Pinus tabuliformis (Carriere) plantations in northern China

Treesearch

Weiwei Wang; Deborah Page-Dumroese; Ruiheng Lv; Chen Xiao; Guolei Li; Yong Liu

2016-01-01

Changes in forest stand structure may alter the activity of invertase, urease, catalase and phenol oxidase after thinning Pinus tabuliformis (Carriére) plantations in Yanqing County of Beijing, China. We examined changes in these soil enzymes as influenced by time since thinning (24, 32, and 40 years since thinning) for 3 seasons (spring, summer and autumn)...

Fall nitrogen fertilization and the biology of Pinus taeda seedling development

Treesearch

Shi-Jean S. Sung; C.C. Black; T.L. Kormanik; P.A. Counce

1997-01-01

In mid-September when stems and roots of nursery-grown loblolly pine (Pinus taeda L.) seedlings are actively accumulating dry weight (DW), an extra 10, 20, or 40 kg NH4NO3 ha-1 (10N, 20N, 4ON) was applied. Seedlings receiving no extra N (0N) were the controls. The temporal patterns...

Laser circular cutting of Kevlar sheets: Analysis of thermal stress filed and assessment of cutting geometry

NASA Astrophysics Data System (ADS)

Yilbas, B. S.; Akhtar, S. S.; Karatas, C.

2017-11-01

A Kevlar laminate has negative thermal expansion coefficient, which makes it difficult to machine at room temperaures using the conventional cutting tools. Contararily, laser machining of a Kevlar laminate provides advantages over the conventional methods because of the non-mechanical contact between the cutting tool and the workpiece. In the present study, laser circular cutting of Kevlar laminate is considered. The experiment is carried out to examine and evaluate the cutting sections. Temperature and stress fields formed in the cutting section are simulated in line with the experimental study. The influence of hole diameters on temperature and stress fields are investigated incorporating two different hole diameters. It is found that the Kevlar laminate cutting section is free from large size asperities such as large scale sideways burnings and attachemnt of charred residues. The maximum temperature along the cutting circumference remains higher for the large diameter hole than that of the small diameter hole. Temperature decay is sharp around the cutting section in the region where the cutting terminates. This, in turn, results in high temperature gradients and the thermal strain in the cutting region. von Mises stress remains high in the region where temperature gradients are high. von Mises stress follows similar to the trend of temperature decay around the cutting edges.

Allozyme differentiation and biosystematics of the Californian closed-cone pines (Pinus subsect. Oocarpae)

Treesearch

Constance I. Millar; Steven H. Strauss; M. Thompson Conkle; Robert D. Westfall

1988-01-01

Allozyme differentiation at 32 loci was studied in the three Californian species of Pinus subsect. Oocarpae: P. attenuata, P. muricata, and P. radiata, and in a small sample of a Latin American species of the subsection, P. oocarpa. The Californian species...

Growth-Mortality Relationships in Piñon Pine (Pinus edulis) during Severe Droughts of the Past Century: Shifting Processes in Space and Time

PubMed Central

Macalady, Alison K.; Bugmann, Harald

2014-01-01

The processes leading to drought-associated tree mortality are poorly understood, particularly long-term predisposing factors, memory effects, and variability in mortality processes and thresholds in space and time. We use tree rings from four sites to investigate Pinus edulis mortality during two drought periods in the southwestern USA. We draw on recent sampling and archived collections to (1) analyze P. edulis growth patterns and mortality during the 1950s and 2000s droughts; (2) determine the influence of climate and competition on growth in trees that died and survived; and (3) derive regression models of growth-mortality risk and evaluate their performance across space and time. Recent growth was 53% higher in surviving vs. dying trees, with some sites exhibiting decades-long growth divergences associated with previous drought. Differential growth response to climate partly explained growth differences between live and dead trees, with responses wet/cool conditions most influencing eventual tree status. Competition constrained tree growth, and reduced trees’ ability to respond to favorable climate. The best predictors in growth-mortality models included long-term (15–30 year) average growth rate combined with a metric of growth variability and the number of abrupt growth increases over 15 and 10 years, respectively. The most parsimonious models had high discriminatory power (ROC>0.84) and correctly classified ∼70% of trees, suggesting that aspects of tree growth, especially over decades, can be powerful predictors of widespread drought-associated die-off. However, model discrimination varied across sites and drought events. Weaker growth-mortality relationships and higher growth at lower survival probabilities for some sites during the 2000s event suggest a shift in mortality processes from longer-term growth-related constraints to shorter-term processes, such as rapid metabolic decline even in vigorous trees due to acute drought stress, and

Growth-mortality relationships in piñon pine (Pinus edulis) during severe droughts of the past century: shifting processes in space and time.

PubMed

Macalady, Alison K; Bugmann, Harald

2014-01-01

The processes leading to drought-associated tree mortality are poorly understood, particularly long-term predisposing factors, memory effects, and variability in mortality processes and thresholds in space and time. We use tree rings from four sites to investigate Pinus edulis mortality during two drought periods in the southwestern USA. We draw on recent sampling and archived collections to (1) analyze P. edulis growth patterns and mortality during the 1950s and 2000s droughts; (2) determine the influence of climate and competition on growth in trees that died and survived; and (3) derive regression models of growth-mortality risk and evaluate their performance across space and time. Recent growth was 53% higher in surviving vs. dying trees, with some sites exhibiting decades-long growth divergences associated with previous drought. Differential growth response to climate partly explained growth differences between live and dead trees, with responses wet/cool conditions most influencing eventual tree status. Competition constrained tree growth, and reduced trees' ability to respond to favorable climate. The best predictors in growth-mortality models included long-term (15-30 year) average growth rate combined with a metric of growth variability and the number of abrupt growth increases over 15 and 10 years, respectively. The most parsimonious models had high discriminatory power (ROC>0.84) and correctly classified ∼ 70% of trees, suggesting that aspects of tree growth, especially over decades, can be powerful predictors of widespread drought-associated die-off. However, model discrimination varied across sites and drought events. Weaker growth-mortality relationships and higher growth at lower survival probabilities for some sites during the 2000s event suggest a shift in mortality processes from longer-term growth-related constraints to shorter-term processes, such as rapid metabolic decline even in vigorous trees due to acute drought stress, and/or increases

Short-term effects of fertilization on loblolly pine (Pinus taeda L.) physiology

Treesearch

C.M. Gough; J.R. Seiler; Chris A. Maier

2004-01-01

Fertilization commonly increases biomass production in loblolly pine (Pinus taeda L.). However, the sequence of short-term physiological adjustments allowing for the establishment of leaf area and enhanced growth is not well understood. The effects of fertilization on photosynthetic parameters, root respiration, and growth for over 200 d following...

Stand-level Allometry in Pinus taeda as Affected by Irrigation and Fertilization

Treesearch

J.S. King; T.J. Albaugh; H.L. Allen; L.W. Kress

1999-01-01

Changing environmental conditions have the potential to alter allometric relationships between plant parts, possibly leading to ecosystem-level feedbacks. We quantified allometric shifts in field-grown loblolly pine (Pinus taeda L.) in response to altered resource availability based on data from multiple harvests to correct for size-related changes...

Multiple nuclear loci reveal the distinctiveness of the threatened, Neotropical Pinus chiapensis

Treesearch

John Syring; Rafael F. del Castillo; Richard Cronn; Aaron Liston

2007-01-01

Pinus chiapensis is a threatened species of pine from southern Mexico and Guatemala. It was first described as a disjunct variety of P. strobus from the eastern United States and Canada. Subsequent morphological work indicates that P. chinpensis is a distinct species, but this interpretation is controversial. To...

Apparatus for cutting elastomeric materials

NASA Technical Reports Server (NTRS)

Corbett, A. B.

1974-01-01

Sharp thin cutting edge is held in head of milling machine designed for metal working. Controls of machine are used to position cutting edge in same plane as vibrating specimen. Controls then are operated, making blade come into contact with specimen, to cut it into shapes and sizes desired. Cut surfaces appear mirror-smooth; vibrating mechanism causes no visible striations.

Recognizing dying in terminal illness.

PubMed

Taylor, Paul M; Johnson, Miriam

2011-08-01

Recognizing dying in terminally ill patients is a complex clinical skill. This article outlines the approach to the decision, common difficulties encountered in patients with both malignant and non-malignant disease, and a simple approach to considering the question 'Is this patient dying?'

Laser cutting plastic materials

NASA Astrophysics Data System (ADS)

Vancleave, R. A.

1980-08-01

A 1000 watt CO2 laser was demonstrated as a reliable production machine tool for cutting of plastics, high strength reinforced composites, and other nonmetals. More than 40 different plastics were laser cut, and the results are tabulated. Applications for laser cutting described include fiberglass reinforced laminates, Kevlar/epoxy composites, fiberglass reinforced phenolics, nylon/epoxy laminates, ceramics, and disposal tooling made from acrylic.

Consumer evaluation of palatability characteristics of a beef value-added cut compared to common retail cuts.

PubMed

Lepper-Blilie, A N; Berg, E P; Germolus, A J; Buchanan, D S; Berg, P T

2014-01-01

The objectives of this study were to educate consumers about value-added beef cuts and evaluate their palatability responses of a value cut and three traditional cuts. Three hundred and twenty-two individuals participated in the beef value cut education seminar series presented by trained beef industry educators. Seminar participants evaluated tenderness, juiciness, flavor, and overall like of four samples, bottom round, top sirloin, ribeye, and a value cut (Delmonico or Denver), on a 9-point scale. The ribeye and the value cut were found to be similar in all four attributes and differed from the top sirloin and bottom round. Correlations and regression analysis found that flavor was the largest influencing factor for overall like for the ribeye, value cut, and top sirloin. The value cut is comparable to the ribeye and can be a less expensive replacement. © 2013.

INTERNAL CUTTING DEVICE

DOEpatents

Russell, W.H. Jr.

1959-06-30

A device is described for removing material from the interior of a hollow workpiece so as to form a true spherical internal surface in a workpiece, or to cut radial slots of an adjustable constant depth in an already established spherical internal surface. This is accomplished by a spring loaded cutting tool adapted to move axially wherein the entire force urging the tool against the workpiece is derived from the spring. Further features of importance involve the provision of a seal between the workpiece and the cutting device and a suction device for carrying away particles of removed material.

Die singulation method and package formed thereby

DOEpatents

Anderson, Robert C [Tucson, AZ; Shul, Randy J [Albuquerque, NM; Clews, Peggy J [Tijeras, NM; Baker, Michael S [Albuquerque, NM; De Boer, Maarten P [Albuquerque, NM

2012-08-07

A method is disclosed for singulating die from a substrate having a sacrificial layer and one or more device layers, with a retainer being formed in the device layer(s) and anchored to the substrate. Deep Reactive Ion Etching (DRIE) etching of a trench through the substrate from the bottom side defines a shape for each die. A handle wafer is then attached to the bottom side of the substrate, and the sacrificial layer is etched to singulate the die and to form a frame from the retainer and the substrate. The frame and handle wafer, which retain the singulated die in place, can be attached together with a clamp or a clip and to form a package for the singulated die. One or more stops can be formed from the device layer(s) to limit a sliding motion of the singulated die.

Dying: A universal human experience?

PubMed

Bregman, L

1989-03-01

This paper explores the question, "Is there a universal psychological experience suffered by all dying persons?" a question to which the popular theory of Kübler-Ross presupposes an affirmative answer. Our answer takes three steps: first, a comparison between the Kübler-Ross model of dying and that of the late medievalBook of the Craft of Dying centered upon the five Kübler-Ross "stages"; second, a philosophical critique of the terms of this comparison; and third, a revised look at the alleged similarities between the two models, providing a deeper look at the moral and spiritual assumptions behind each.

Uptake of trifluoroacetate by Pinus ponderosa via atmospheric pathway

NASA Astrophysics Data System (ADS)

Benesch, J. A.; Gustin, M. S.

Trifluoroacetate (TFA, CF 3COO -), a break down product of hydro(chloro)-fluorocarbons (HFC/HCFCs), has been suggested to contribute to forest decline syndrome. To investigate the possible effects, Pinus ponderosa was exposed to TFA applied as mist (150 and 10,000 ng l -1) to foliar surfaces. Needles accumulated TFA as a function of concentration and time. However, no adverse physiological responses, as plant morphology, photosynthetic and conductance rates, were observed at the TFA concentrations used in this study.

Pinus ponderosa: a taxonomic review with five subspecies in the United States

Treesearch

Robert Z. Callaham

2013-01-01

Various forms of Pinus ponderosa Douglas ex C. Lawson are found from British Columbia southward and eastward through 16 states and, perhaps, into Mexico. The status of many names previously associated with this species, but excluded here, has been clarified. Accumulated evidence based on variation in morphology and xylem monoterpenes,...

Force-frequency effect of Y-cut langanite and Y-cut langatate.

PubMed

Kim, Yoonkee; Ballato, Arthur

2003-12-01

Most recently, langasite and its isomorphs (LGX) have been advanced as potential substitutes for quartz, owing to their extremely high-quality (Q) factors. At least twice higher Q value of LGX than that of quartz has been reported. High Q translates into potentially greater stability. In order to make such materials practical, the environmental sensitivities must be addressed. One of such sensitivities is the force-frequency effect, which relates the sensitiveness of a resonator to shock and vibration via the third-order (non-Hookean) elastic constants. In this paper, we report measured force-frequency coefficients of a Y-cut langanite (LGN) resonator and a Y-cut langatate (LGT) resonator as a function of the azimuthal angle, which is the angle between the crystalline x-axis of a resonator plate and the direction of in-plane diametric force applied to the periphery of the resonator. It was found that the LGN and the LGT behave like AT-cut quartz in the polarity of the frequency changes and the existence of zero-coefficient angle. The maximum magnitudes of the coefficients of the LGN and the LGT are five and seven times smaller than that of stress-compensated cut (SC-cut) quartz, respectively (or, 7 and 10 times smaller comparing to AT-cut quartz). The coefficients of planar-stress, which represent the superposition of a continuous distribution of periphery stresses, also were obtained as 0.52 X 10(-15) m x s/N and 0.38 X 10(-15) m x s/N for the LGN and the LGT, respectively.

Genetic variation in basal area increment phenology and its correlation with growth rate in loblolly and slash pine families and clones

Treesearch

Veronica I. Emhart; Timothy A. Martin; Timothy L. White; Dudley A. Huber

2006-01-01

We quantified basal area increment phenology over a 2-year period in one loblolly pine (Pinus taeda L.) and four slash pine (Pinus elliottii Engelm. var. elliottii) full-sib families propagated as rooting cuttings. In 2002, basal area growth started in March and stopped in October for both species, while in 2003, initiation and cessation occurred 2...

["Good dying"--definition and current state of research].

PubMed

Hutter, Nico; Stößel, Ulrich; Meffert, Cornelia; Körner, Mirjam; Bozzaro, Claudia; Becker, Gerhild; Baumeister, Harald

2015-08-01

The advances of modern medicine did not only result in prolongation of life expectancy, but also led to a shift from dying at home to dying in public institutions. In western countries most people die at advanced age in medical facilities. Hence, the question regarding the conditions, which should be provided by society and especially medicine, to allow terminally ill people to experience "good dying" is substantial. For this purpose, an examination of patients', family members' and health care providers' understanding of the term " good dying" is required. The present paper aims at shedding light on the term "good dying" and to summarize the current state of research. Therefore, the attributes of "good dying" will be described from the perspectives of patients, family members and health care providers, which are discussed and examined in current medical-sociological research. These attributes can be illustrated on three dimensions: Quality of life at the end of life (e. g. pain relief, mental well-being), quality of dying (e. g. avoiding prolonged dying, autonomy, presence of relatives) and quality of health care at the end of life (e. g. patient-oriented health care, positive communication between health care providers and patients, availability of guidelines). Although the attributes of "good dying" are described in detail in the existing literature, further studies have to clarify the relevance and impact of these attributes as predictors of "good dying". © Georg Thieme Verlag KG Stuttgart · New York.

Bereits nach Ablauf der Halbwertszeit droht der vollständige Zerfall Die britische Atomic Scientists’ Association, die Ideologie der „objektiven” Wissenschaft und die H-Bombe

NASA Astrophysics Data System (ADS)

Laucht, Christoph

Präsident Harry Trumans Verlautbarung vom 31.1.1950, seine Regierung wolle die Entwicklung der Wasserstoffbombe vorantreiben, fand große Beachtung in den britischen Medien. Die illustrierte Zeitschrift Picture Post widmete der HBombe einen Artikel, der unter anderem kurze Stellungnahmen der britischen Atomwissenschaftler Eric Burhop, Kathleen Lonsdale, Harrie Massey, Rudolf Peierls und Maurice Pryce enthielt, die alle Mitglieder der Atomic Scientists' Association (ASA) waren.

Factors Affecting the Emission of Monoterpenes from Red Pine (Pinus densiflora)

PubMed Central

Yokouchi, Yoko; Ambe, Yoshinari

1984-01-01

The mechanism of monoterpene emission from Pinus densiflora was studied using an environmentally controlled gas cabinet. It was found that monoterpene emission rate increases exponentially with temperature and is also influenced by light. These observations were explained reasonably by a mechanism whereby monoterpene emission rate depends on the monoterpene amount in the leaf oil and its saturated vapor pressure. PMID:16663724

Forest floor depth mediates understory vigor in xeric Pinus palustris ecosystems

Treesearch

J. Kevin Hiers; Joseph J. O' Brien; Rodney E. Will; Robert J. Mitchell

2007-01-01

Longleaf pine (Pinus palustris) woodlands and savannas are among the most frequently burned ecosystems in the world with fire return intervals of 1–10 years. This fire regime has maintained high levels of biodiversity in terms of both species richness and endemism. Land use changes have reduced the area of this ecosystem by .95%, and inadequate fire...

Chapter 8 optimized test design for identification of the variation of elastic stiffness properties of Loblolly Pine (Pinus taeda) pith to bark

Treesearch

David Kretschmann; John Considine; F. Pierron

2016-01-01

This article presents the design optimization of an un-notched Iosipescu test specimen whose goal is the characterization of the material elastic stiffnesses of a Loblolly (Pinus taeda) or Lodgepole pine (Pinus contorta) sample in one single test. A series of finite element (FE) and grid simulations were conducted to determine displacement and strain fields for various...

Optimisation Of Cutting Parameters Of Composite Material Laser Cutting Process By Taguchi Method

NASA Astrophysics Data System (ADS)

Lokesh, S.; Niresh, J.; Neelakrishnan, S.; Rahul, S. P. Deepak

2018-03-01

The aim of this work is to develop a laser cutting process model that can predict the relationship between the process input parameters and resultant surface roughness, kerf width characteristics. The research conduct is based on the Design of Experiment (DOE) analysis. Response Surface Methodology (RSM) is used in this work. It is one of the most practical and most effective techniques to develop a process model. Even though RSM has been used for the optimization of the laser process, this research investigates laser cutting of materials like Composite wood (veneer)to be best circumstances of laser cutting using RSM process. The input parameters evaluated are focal length, power supply and cutting speed, the output responses being kerf width, surface roughness, temperature. To efficiently optimize and customize the kerf width and surface roughness characteristics, a machine laser cutting process model using Taguchi L9 orthogonal methodology was proposed.

The effect of cutting parameters on the performance of ZTA-MgO cutting tool

NASA Astrophysics Data System (ADS)

Ali, A. M.; Hamidon, N. E.; Zaki, N. K. M.; Mokhtar, S.; Azhar, A. Z. A.; Bahar, R.; Ahmad, Z. A.

2018-01-01

The effect of cutting parameters on the performances of ZTA-MgO ceramic cutting tool investigated. The aim of this project is to discover the effect of cutting speed and feedrate on the performance of the ZTA-MgO cutting tool via wear and surface roughness measurement. CNC turning machining performed using the cutting speed, Vc range from 354 to 471 m/min and the feed rate, f 0.1, 0.3 and 0.5 mm/rev while the depth of cut, d is kept constant at 0.2 mm. The flank wear, crater wear, and chipping were measured accordingly using optical microscope, Matlab programming and SEM. Surface roughness of machined stainless steel 316L surface were measured using the surface roughness tester (Mitutoyo MTR097-8. The result showing the increment trend of flank wear with increment of cutting speed and feed rate with the lowest value of flank wear, 0.061 mm achieved at Vc = 354 m/min and f = 0.1 mm/rev while the highest flank wear is 0.480 mm at Vc = 471 m/min and f = 0.5 mm/rev. The increasing pattern also observed in the crater wear results. The lowest area of crater wear is 2.2736 mm2 at Vc = 354 m/min and f = 0.1 mm/rev while the highest value is 4.8524 mm2 at Vc = 471 m/min and f = 0.5 mm/rev. As for the surface roughness, the higher the cutting speed, the lower the average roughness (Ra) value. Cutting speed, Vc = 471 m/min with f = 0.1 mm/rev has the lowest value of Ra which is 0.72µm.

Taxonomic Revision of Pinus fujiii (Yasui) Miki (Pinaceae) and Its Implications for the Phytogeography of the Section Trifoliae in East Asia

PubMed Central

Yamada, Toshihiro; Yamada, Mariko; Tsukagoshi, Minoru

2015-01-01

Pinus trifolia Miki 1939 (Pinaceae) was originally proposed based on seed cones from the upper Miocene of Aichi and Gifu Prefectures, central Japan. However, before the publication of P. trifolia, a different name (Pinus fujiii (Yasui) Miki) was given to a female cone with the same morphology. On the other hand, P. fujiii auct. non (Yasui) Miki has been used for seed cones with different morphologies from Yasui’s holotype, i.e., apophyses arranged in 5:8 parastichies and a perexcentromucronate slightly-pointed umbo. As a result of re-examination on the Miki and Yasui specimens, we concluded that P. trifolia was a synonym for P. fujiii and proposed here Pinus mikii sp. nov. for cones assigned to P. fujiii auct. non (Yasui) Miki. We also emended the diagnosis of P. fujiii based on these specimens. Pinus fujiii is characterized by a large female cone in which the apophyses with a centromucronate prickle-like umbo are arranged in 8:13 parastichies, and deciduous seed wings. These characters suggest that P. fujiii belongs to the section Trifoliae of the subgenus Pinus, which is now restricted to North and Central America and the Caribbean islands. Fossil data suggest that the P. fujiii lineage firstly appeared in Japan around the Eocene/Oligocene boundary. We speculate that the P. fujiii lineage might have moved southward to Japan from a refugium located elsewhere in high-latitude areas in response to the late Eocene cooling event, as occurred with other Trifoliae species in North America. PMID:26673795

Effects of fire season on vegetation in longleaf pine (Pinus palustris) forests

Treesearch

Bryan T. Mudder; G. Geoff Wang; Joan L. Walker; J. Drew Lanham; Ralph Costa

2010-01-01

Forest managers in the Southeastern United States are interested in the restoration of not only longleaf pine (Pinus palustris) trees, but also the characteristic forest structure and ground-layer vegetation of the longleaf pine ecosystem. Season of burn, fire intensity, and fire frequency are critical components of a fire regime that supports...

Influences of community composition on biogeochemistry of loblolly pine (Pinus taeda) systems

Treesearch

B.G. Lockaby; J.H. Miller; R.G. Clawson

1995-01-01

Litterfall and decomposition processes were compared among four forest plantations that were dominated by loblolly pine (Pinus taeda L) but that differed.in terms of presence or absence of deciduous and herbaceous components. Based on aboveground litterfall, the pine-only community was the most productive but had the slowest turnover of organic...

Thinning ponderosa pine (Pinus ponderosa) stands reduces mortality while maintaining stand productivity

Treesearch

Jianwei Zhang; Martin W. Ritchie; Douglas A. Maguire; William W. Oliver

2013-01-01

We analyzed 45-yr data collected from three ponderosa pine (Pinus ponderosa Lawson & C. Lawson) levels-of-growing-stock installations in Oregon (OR) and northern California (CA), USA, to determine the effect of stand density regimes on stand productivity and mortality. We found that periodic annual increment (PAI) of diameter, basal area (BA...

Growth and physiological responses to varied environments among populations of Pinus ponderosa

Treesearch

Jianwei Zhang; Bert M. Cregg

2005-01-01

We investigated population responses in physiology, morphology, and growth of mature Pinus ponderosa trees to an environmental gradient across Nebraska, USA. Ten populations from western Nebraska and eastern Wyoming were grown in three 26-year-old provenance tests from the warmest and wettest site in the east (Plattsmouth) to the intermediate site in...

Seasonal ectomycorrhizal fungal biomass development on loblolly pine (Pinus taeda L.) seedlings

Treesearch

Shi-Jean S. Sung; L.M. White; D.H. Marx; W.J. Otrosina

1995-01-01

Ergosterol, a membrane sterol found in fungi but not in plants, was used to estimate live mycelia biomass in ectomycorrhizae. Loblolly pine (Pinus taeda L.) seeds were sown in April 1993 and grown with standard nursery culture ractices. Correlations between total seedling ergosterol and visual assessment of mycorrhizal colonization were high during...

Chloroplast microsatellites reveal population genetic diversity in red pine, Pinus resinosa Ait

Treesearch

Craig S. Echt; L.L. DeVerno; M. Anzidei; G.G. Vendramin

1998-01-01

Variation in paternally inherited chloroplast microsatellite (cpSSR) DNA was used to study population genetic structure in red pine (Pinus resinosa Ait.), a species characterized by morphological uniformity, no allozyme variation, and limited RAPD variation. Using nine cpSSR loci, a total of 23 chloroplast haplotypes and 25 cpSSR alleles were were...

Transcriptome analysis of Pinus halepensis under drought stress and during recovery

PubMed Central

Fox, Hagar; Doron-Faigenboim, Adi; Kelly, Gilor; Bourstein, Ronny; Attia, Ziv; Zhou, Jing; Moshe, Yosef; Moshelion, Menachem; David-Schwartz, Rakefet

2018-01-01

Abstract Forest trees use various strategies to cope with drought stress and these strategies involve complex molecular mechanisms. Pinus halepensis Miller (Aleppo pine) is found throughout the Mediterranean basin and is one of the most drought-tolerant pine species. In order to decipher the molecular mechanisms that P. halepensis uses to withstand drought, we performed large-scale physiological and transcriptome analyses. We selected a mature tree from a semi-arid area with suboptimal growth conditions for clonal propagation through cuttings. We then used a high-throughput experimental system to continuously monitor whole-plant transpiration rates, stomatal conductance and the vapor pressure deficit. The transcriptomes of plants were examined at six physiological stages: pre-stomatal response, partial stomatal closure, minimum transpiration, post-irrigation, partial recovery and full recovery. At each stage, data from plants exposed to the drought treatment were compared with data collected from well-irrigated control plants. A drought-stressed P. halepensis transcriptome was created using paired-end RNA-seq. In total, ~6000 differentially expressed, non-redundant transcripts were identified between drought-treated and control trees. Cluster analysis has revealed stress-induced down-regulation of transcripts related to photosynthesis, reactive oxygen species (ROS)-scavenging through the ascorbic acid (AsA)-glutathione cycle, fatty acid and cell wall biosynthesis, stomatal activity, and the biosynthesis of flavonoids and terpenoids. Up-regulated processes included chlorophyll degradation, ROS-scavenging through AsA-independent thiol-mediated pathways, abscisic acid response and accumulation of heat shock proteins, thaumatin and exordium. Recovery from drought induced strong transcription of retrotransposons, especially the retrovirus-related transposon Tnt1-94. The drought-related transcriptome illustrates this species’ dynamic response to drought and recovery

Cutting process simulation of flat drill

NASA Astrophysics Data System (ADS)

Tamura, Shoichi; Matsumura, Takashi

2018-05-01

Flat drills at a point angle of 180 deg. have recently been developed for drilling of automobile parts with the inclination of the workpiece surfaces. The paper studies the cutting processes of the flat drills in the analytical simulation. A predictive force model is applied to simulation of the cutting force with the chip flow direction. The chip flow model is piled up with orthogonal cuttings in the plane containing the cutting velocities and the chip flow velocities, in which the chip flow direction is determined to minimize the cutting energy. Then, the cutting force is predicted in the determined in the chip flow model. The typical cutting force of the flat drill is discussed with comparing to that of the standard drill. The typical differences are confirmed in the cutting force change during the tool engagement and disengagement. The cutting force, then, is simulated in drilling for an inclined workpiece with a flat drill. The horizontal components in the cutting forces are simulated with changing the inclination angle of the plate. The horizontal force component in the flat drilling is stable to be controlled in terms of the machining accuracy and the tool breakage.

Laser Cutting of Thin Nickel Bellows

NASA Technical Reports Server (NTRS)

Butler, C. L.

1986-01-01

Laser cutting technique produces narrow, precise, fast, and repeatable cuts in thin nickel-allow bellows material. Laser cutting operation uses intense focused beam to melt material and assisting gas to force melted material through part thickness, creating void. When part rotated or moved longitudinally, melting and material removal continuous and creates narrow, fast, precise, and repeatable cut. Technique used to produce cuts of specified depths less than material thickness. Avoids distortion, dents, and nicks produced in delicate materials during lathe trimming operations, which require high cutting-tool pressure and holding-fixture forces.

Die Deformation Measurement System during Sheet Metal Forming

NASA Astrophysics Data System (ADS)

Funada, J.; Takahashi, S.; Fukiharu, H.

2011-08-01

In order to reduce affection to the earth environment, it is necessary to lighten the vehicles. For this purpose, high tensile steels are applied. Because of high strength, high forming force is required for producing automotive sheet metal parts. In this situation, since the dies are elastic, they are deformed during forming parts. For reducing die developing period, sheet metal forming simulation is widely applied. In the numerical simulation, rigid dies are usually used for shortening computing time. It means that the forming conditions in the actual forming and the simulation are different. It will make large errors in the results between actual forming and simulation. It can be said that if contact pressure between dies and a sheet metal in the simulation can be reproduced in the actual forming, the differences of forming results between them can also been reduced. The basic idea is to estimate die shape which can produce the same distribution as computed from simulation with rigid dies. In this study, die deformation analyses with Finite Element Method as basic technologies are evaluated. For example, simple shape and actual dies elastic contact problems were investigated. The contact width between simple shape dies was investigated. The computed solutions were in good agreement with experimental results. The one case of the actual dies in two cases was also investigated. Bending force was applied to the blank holder with a mechanical press machine. The methodology shown with applying inductive displacement sensor for measuring die deformation during applying force was also proposed.

Einführung in die Technische Chemie

NASA Astrophysics Data System (ADS)

Behr, Arno; Agar, David W.; Jörissen, Jakob

Die "Technische Chemie" ist ein Lehrfach an Universitäten und Hochschulen. Nach dem die Studierenden der Chemie in den ersten Semestern ihres Studiums ausrei chen de theoretische Kenntnisse in Allgemeiner, Anorganischer, Organischer und Physikalischer Chemie erlangt haben, soll die Technische Chemie einen Blick auf die praktische Anwendung dieser Naturwissenschaft in unserer Wirtschaft lenken. Es gibt keine "biologische Industrie", "physikalische Industrie" oder "mathematische Industrie", wohl aber seit über 150 Jahren eine "chemische Industrie", die in dieser lan gen Zeit zahlreiche chemische Prozesse entwickelt und dazu vielfältige Methoden erarbeitet hat. Das Lehrfach Technische Chemie gibt einen Überblick über diese Pro zesse und Methoden und erleichtert dadurch den Schritt von der Universität zur be ruflichen Praxis.

Short-term effects of prescribed burning on litterfall biomass in mixed stands of Pinus nigra and Pinus pinaster and pure stands of Pinus nigra in the Cuenca Mountains (Central-Eastern Spain).

PubMed

Espinosa, J; Madrigal, J; De La Cruz, A C; Guijarro, M; Jimenez, E; Hernando, C

2018-03-15

Fire severity, defined as the magnitude of fire effects in an ecosystem, is a key factor to consider in planning management strategies for protecting forests against fire. Although prescribed burning has been used as a fuel reduction tool in forest ecosystems, it is quite limited in the Mediterranean region. Furthermore, little is known about how tree crowns are affected by prescribed underburning aimed at reducing fire severity in conifer stands. As part of an ongoing study to assess the effects of prescribed burning on the tree canopy, litterfall is currently being monitored in a network of experimental plots located in mixed (Pinus nigra and Pinus pinaster) and pure (P. nigra) conifer stands in the Cuenca Mountains (Castilla La Mancha, Spain). A total of 12 study plots (30m×30m) were established in a completely randomized experimental design to determine the effect of burning, with 2 treatments: no burning (control) and burning (i.e. with three replicate plots for each treatment and site). Burning was conducted in May 2016. In each plot, 8 litterfall collectors were installed at regular intervals, according to international protocols (ICP Forests), and all biomass falling into the collectors is being monitored monthly. The specific objective of this study is to assess how prescribed burning affects the rate of generation of foliar and non-foliar litterfall biomass due to the fire. In addition, the Leaf Area Index was estimated before burning and one year later to verify possible changes in the structure of the stands. This information could be used to help minimize the negative impacts of prescribed underburning on litterfall. To our knowledge, this study represents the first attempt to evaluate the effect of prescribed burning on litterfall biomass in Europe. Copyright © 2017 Elsevier B.V. All rights reserved.

Volatile compound in cut and un-cut flowers of tetraploid Freesia hybrida.

PubMed

Ao, Man; Liu, Baofeng; Wang, Li

2013-01-01

The flower volatile compounds (FVCs) of two tetraploid Freesia hybrida (pink-yellow and yellow) cultivars and their cut flowers were analysed by headspace solid-phase microextraction combined with gas chromatography-mass spectrometry. Twelve FVCs were identified in the pink-yellow cultivar, with linalool as the major compound; 30 FVCs were identified in the yellow cultivar, with linalool and terpineol as the two major compounds. The FVCs (>1%) of the two cut flower cultivars were very similar to that of the un-cut flowers, and no significant difference was observed.

Laser cutting of various materials: Kerf width size analysis and life cycle assessment of cutting process

NASA Astrophysics Data System (ADS)

Yilbas, Bekir Sami; Shaukat, Mian Mobeen; Ashraf, Farhan

2017-08-01

Laser cutting of various materials including Ti-6Al-4V alloy, steel 304, Inconel 625, and alumina is carried out to assess the kerf width size variation along the cut section. The life cycle assessment is carried out to determine the environmental impact of the laser cutting in terms of the material waste during the cutting process. The kerf width size is formulated and predicted using the lump parameter analysis and it is measured from the experiments. The influence of laser output power and laser cutting speed on the kerf width size variation is analyzed using the analytical tools including scanning electron and optical microscopes. In the experiments, high pressure nitrogen assisting gas is used to prevent oxidation reactions in the cutting section. It is found that the kerf width size predicted from the lump parameter analysis agrees well with the experimental data. The kerf width size variation increases with increasing laser output power. However, this behavior reverses with increasing laser cutting speed. The life cycle assessment reveals that material selection for laser cutting is critical for the environmental protection point of view. Inconel 625 contributes the most to the environmental damages; however, recycling of the waste of the laser cutting reduces this contribution.

Labdane-type diterpenes active against acne from pine cones (Pinus densiflora).

PubMed

Sultan, Md Zakir; Jeon, Young-Min; Moon, Surk-Sik

2008-03-01

Bioassay-guided extraction and fractionation of the aqueous methanolic extract of the cones of Pinus densiflora (Pinaceae) afforded one new labdane-type diterpene aldehyde, 15-nor-14-oxolabda-8(17),12 E-diene-18-oic acid, along with eight known diterpenes. Their structures were elucidated using spectroscopic methods as well as by comparison with previously reported data. The isolates showed antibacterial (Propionibacterium acnes) and antifungal activities.

[Genetic variation of geographical provenance of Pinus massoniana--review and analysis].

PubMed

Li, D; Peng, S

2000-04-01

Pinus massoniana is a significant tree species constituting the subtropical forests in China. Based on morphological, physio-ecological, chromosome, and molecular levels, the genetic variation of geographical provenance of P. massoniana and its distribution were reviewed, and the methodologies on genetic diversity and the genetic variation patterns of geographical provenance of P. massoniana were synthetically analyzed. The Key problems on molecular ecology of P. massoniana were discussed.

Spatial pattern of allozyme variation in a contact zone of Pinus Ponderosa and P. arizonica (Pinaceae).

PubMed

Epperson, Bryan K; Chung, Myong Gi; Telewski, Frank W

2003-01-01

The spatial distribution of genotypes for nine polymorphic allozyme loci was examined in a contact zone between Pinus ponderosa var. scopulorum and another tree regarded as either a separate species, Pinus arizonica, or variety, Pinus ponderosa var. arizonica, in southern Arizona. Previous work had identified a steep elevational cline for a key taxonomic trait, number of leaf-needles per fascicle, on the south slope of Mt. Lemmon. The present results indicate that the taxa are not fully interbreeding in this contact zone, because allozyme genotypes are considerably more spatially structured than expected for the dispersal characteristics of pines. The amount of spatial differentiation is also much less than that observed for needle number. It appears that this is due to the lack of differentiation for allozyme gene frequencies for the two types of trees, which is further evidenced by analysis of samples from two other populations away from the contact zone. It is likely that if the two taxa were isolated in the past, it was not for long enough nor complete enough to allow mutation-drift to create substantial differentiation between them. Another possible explanation is that introgression after recontact is so advanced that any differences have been erased throughout the Santa Catalina mountain range.

ADVANCED CUTTINGS TRANSPORT STUDY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stefan Miska; Troy Reed; Ergun Kuru

2004-09-30

The Advanced Cuttings Transport Study (ACTS) was a 5-year JIP project undertaken at the University of Tulsa (TU). The project was sponsored by the U.S. Department of Energy (DOE) and JIP member companies. The objectives of the project were: (1) to develop and construct a new research facility that would allow three-phase (gas, liquid and cuttings) flow experiments under ambient and EPET (elevated pressure and temperature) conditions, and at different angle of inclinations and drill pipe rotation speeds; (2) to conduct experiments and develop a data base for the industry and academia; and (3) to develop mechanistic models for optimizationmore » of drilling hydraulics and cuttings transport. This project consisted of research studies, flow loop construction and instrumentation development. Following a one-year period for basic flow loop construction, a proposal was submitted by TU to the DOE for a five-year project that was organized in such a manner as to provide a logical progression of research experiments as well as additions to the basic flow loop. The flow loop additions and improvements included: (1) elevated temperature capability; (2) two-phase (gas and liquid, foam etc.) capability; (3) cuttings injection and removal system; (4) drill pipe rotation system; and (5) drilling section elevation system. In parallel with the flow loop construction, hydraulics and cuttings transport studies were preformed using drilling foams and aerated muds. In addition, hydraulics and rheology of synthetic drilling fluids were investigated. The studies were performed under ambient and EPET conditions. The effects of temperature and pressure on the hydraulics and cuttings transport were investigated. Mechanistic models were developed to predict frictional pressure loss and cuttings transport in horizontal and near-horizontal configurations. Model predictions were compared with the measured data. Predominantly, model predictions show satisfactory agreements with the measured

Development of a 2-stage shear-cutting-process to reduce cut-edge-sensitivity of steels

NASA Astrophysics Data System (ADS)

Gläsner, T.; Sunderkötter, C.; Hoffmann, H.; Volk, W.; Golle, R.

2017-09-01

The edge cracking sensitivity of AHSS and UHSS is a challenging factor in the cold forming process. Expanding cut holes during flanging operations is rather common in automotive components. During these flanging operations the pierced hole is stretched so that its diameter is increased. These flanging operations stretch material that has already been subjected to large amounts of plastic deformation, therefore forming problems may occur. An innovative cutting process decreases micro cracks in the cutting surface and facilitates the subsequent cold forming process. That cutting process consists of two stages, which produces close dimensional tolerance and smooth edges. As a result the hole expanding ratio was increased by nearly 100 % when using thick high strength steels for suspension components. The paper describes the mechanisms of the trimming process at the cut edge, and the positive effect of the 2-stage shear-cutting process on the hole extension capability of multiphase steels.

In vitro comparison of the cutting efficiency and temperature production of 10 different rotary cutting instruments. Part I: Turbine.

PubMed

Ercoli, Carlo; Rotella, Mario; Funkenbusch, Paul D; Russell, Scott; Feng, Changyong

2009-04-01

Standards to test the cutting efficiency of dental rotary cutting instruments are either nonexistent or inappropriate, and knowledge of the factors that affect their cutting performance is limited. Therefore, rotary cutting instruments for crown preparation are generally marketed with weak or unsupported claims of superior performance. The purpose of this study was to examine the cutting behavior of a wide selection of rotary cutting instruments under carefully controlled and reproducible conditions with an air-turbine handpiece. Ten groups of rotary cutting instruments (n=30) designed for tooth preparation were selected: 9 diamond rotary cutting instruments (7 multi-use, 2 disposable) and 1 carbide bur. One bur per group was imaged with a scanning electron microscope (SEM) at different magnifications. Macor blocks (n=75) were used as a substrate, and 4 cuts were made on each specimen, using a new rotary cutting instrument each time, for a total of 300 cuts. The cuts were performed with an air-turbine handpiece (Midwest Quiet Air). A computer-controlled, custom-made testing apparatus was used to monitor all sensors and control the cutting action. The data were analyzed to compare the correlation of rotary cutting instrument type, grit, amount of pressure, cutting rate, revolutions per minute (rpm), temperature, and type of handpiece, using 1-way ANOVA and Tukey's Studentized Range test (alpha=.05). Compared to the baseline temperature, all rotary cutting instruments showed a reduction of temperature in the simulated pulp chamber. The Great White Ultra (carbide bur) showed a significantly higher rate of advancement (0.15 mm/s) and lower applied load (106.46 g) and rpm (304,375.97). Tooth preparation with an adequate water flow does not cause harmful temperature changes in the pulp chamber, regardless of rotary cutting instrument type. The tested carbide bur showed greater cutting efficiency than all diamond rotary cutting instruments.

Plasma Cutting and Carbon-Arc Cutting. Welding Module 8. Instructor's Guide.

ERIC Educational Resources Information Center

Missouri Univ., Columbia. Instructional Materials Lab.

This guide is intended to assist vocational educators in teaching the two units of a module in operating plasma cutting and carbon-arc cutting equipment. The module is part of a welding curriculum that has been designed to be totally integrated with Missouri's Vocational Instruction Management System. The materials included in the module have been…

25 CFR 301.4 - Application of dies.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 25 Indians 2 2010-04-01 2010-04-01 false Application of dies. 301.4 Section 301.4 Indians INDIAN ARTS AND CRAFTS BOARD, DEPARTMENT OF THE INTERIOR NAVAJO, PUEBLO, AND HOPI SILVER AND TURQUOISE PRODUCTS; STANDARDS § 301.4 Application of dies. Dies are to be applied to the object with the aid of...

Spatio-temporal change in forest cover and carbon storage considering actual and potential forest cover in South Korea.

PubMed

Nam, Kijun; Lee, Woo-Kyun; Kim, Moonil; Kwak, Doo-Ahn; Byun, Woo-Hyuk; Yu, Hangnan; Kwak, Hanbin; Kwon, Taesung; Sung, Joohan; Chung, Dong-Jun; Lee, Seung-Ho

2015-07-01

This study analyzes change in carbon storage by applying forest growth models and final cutting age to actual and potential forest cover for six major tree species in South Korea. Using National Forest Inventory data, the growth models were developed to estimate mean diameter at breast height, tree height, and number of trees for Pinus densiflora, Pinus koraiensis, Pinus rigida, Larix kaempferi, Castanea crenata and Quercus spp. stands. We assumed that actual forest cover in a forest type map will change into potential forest covers according to the Hydrological and Thermal Analogy Groups model. When actual forest cover reaches the final cutting age, forest volume and carbon storage are estimated by changed forest cover and its growth model. Forest volume between 2010 and 2110 would increase from 126.73 to 157.33 m(3) hm(-2). Our results also show that forest cover, volume, and carbon storage could abruptly change by 2060. This is attributed to the fact that most forests are presumed to reach final cutting age. To avoid such dramatic change, a regeneration and yield control scheme should be prepared and implemented in a way that ensures balance in forest practice and yield.

Nursing students' experiences caring for dying patients.

PubMed

Beck, C T

1997-11-01

Since the 1960s nurse educators have been searching for the most effective approach to prepare nursing students for care of the dying. Studies investigating the effectiveness of death education programs for nursing students have reported inconsistent findings. A phenomenological study was conducted to explore the meaning of 26 undergraduate nursing students' experiences in caring for dying patients. The nursing students' written descriptions of their experiences were analyzed using Colaizzi's (1978) phenomenological method. Six themes emerged from this analysis. While caring for dying patients, nursing students experienced a gamut of emotions such as fear, sadness, frustration, and anxiety. Contemplation of the patient's life and death occurred as the students cared for their patients. In addition to providing physical, emotional, and spiritual support for dying patients, an integral part of nursing students' care involved supporting the patients' families. Helplessness was experienced by the students regarding their role as patient advocates. While caring for dying patients, nursing students' learning fluorished. Educational strategies for preparing nursing students to care for the dying are addressed based on the findings of this qualitative study.

Point of no return: experimental determination of the lethal hydraulic threshold during drought for loblolly pine (Pinus taeda)

NASA Astrophysics Data System (ADS)

Hammond, W.; Yu, K.; Wilson, L. A.; Will, R.; Anderegg, W.; Adams, H. D.

2017-12-01

The strength of the terrestrial carbon sink—dominated by forests—remains one of the greatest uncertainties in climate change modelling. How forests will respond to increased variability in temperature and precipitation is poorly understood, and experimental study to better inform global vegetation models in this area is needed. Necessary for achieving­­­­ this goal is an understanding of how increased temperatures and drought will affect landscape level distributions of plant species. Quantifying physiological thresholds representing a point of no return from drought stress, including thresholds in hydraulic function, is critical to this end. Recent theoretical, observational, and modelling research has converged upon a threshold of 60 percent loss of hydraulic conductivity at mortality (PLClethal). However, direct experimental determination of lethal points in conductivity and cavitation during drought is lacking. We quantified thresholds in hydraulic function in Loblolly pine, Pinus taeda, a commercially important timber species. In a greenhouse experiment, we exposed saplings (n = 96 total) to drought and rewatered treatment groups at variable levels of increasing water stress determined by pre-selected targets in pre-dawn water potential. Treatments also included a watered control with no drought, and drought with no rewatering. We measured physiological responses to water stress, including hydraulic conductivity, native PLC, water potential, foliar color, canopy die-back, and dark-adapted chlorophyll fluorescence. Following the rewatering treatment, we observed saplings for at least two months to determine which survived and which died. Using these data we calculated lethal physiological thresholds in water potential, directly measured PLC, and PLC inferred from water potential using a hydraulic vulnerability curve. We found that PLClethal inferred from water potential agreed with the 60% threshold suggested by previous research. However, directly

Der Einfluss der Digitalisierung auf die Organisation eines Unternehmens

NASA Astrophysics Data System (ADS)

Walter, Wolfram M.

Die Digitalisierung schreitet mit großen Schritten voran. Dies wirkt sich nicht nur auf die Gesellschaft im Grundsatz, sondern auch auf das Verhalten der Kunden aus. Neue Kommunikationswege beschleunigen die Interaktion zwischen Unternehmen und Verbraucher. Im Vergleich mit großen Internetfirmen werden etablierte Dienstleistungsunternehmen - vom Energieversorger bis zu Versicherungen - stark unter Druck gesetzt, sich noch intensiver mit dem Kundenservice auseinanderzusetzen. Dies wird nur möglich sein, wenn sich die Organisationen entsprechend positionieren und sich frühzeitig auf die Veränderungen einstellen. Hieraus ergeben sich mehr Chancen als Risiken, zumal es nicht nur neue Prozesse, sondern auch neue Berufsbilder geben wird.

Loblolly pine: the ecology and culture of loblolly pine (Pinus taeda L.)

Treesearch

Robert P. Schultz

1997-01-01

Loblolly pine ranks as a highly valuable tree for its pulp, paper, and lumber products. In the South, loblolly is planted more than any other conifer. Loblolly Pine: The Ecology and Culture of Loblolly Pine (Pinus taeda L.) adds to the technical foundations laid by Ashe (1915) and Wahlenberg (1960). Agriculture Handbook 713 encompasses genetics, tree...

Strength reduction in slash pine (Pinus elliotii) wood caused by decay fungi

Treesearch

Zhong Yang; Zhehui Jiang; Chung Y. Hse; Todd F. Shupe

2009-01-01

Small wood specimens selected from slash pine (Pinus elliotii )trees at three growth rates (fast, medium, and slow) were inoculated with brown-rot and white-rot fungi and then evaluated for work to maximum load (WML), modulus of rupture (MOR), and modulus of elasticity (MOE). The experimental variables studied included a brown-rot fungus (Gloeophyllum trabeum...

Slash Pine (Pinus Elliottii), Including South Florida Slash Pine: Nomenclature and Description

Treesearch

Elbert L. Little; Keith W. Dorman

1954-01-01

Slash pine (Pinus elliottii Engelm.), including its variation South Florida slash pine recently distinguished as a new botanical variety, has been known by several different scientific names. As a result, the common name slash pine is more precise and clearer than scientific names. The slash pine of southern Florida differs from typical slash pine in a few characters...

Numerical simulation and experiment on multilayer stagger-split die.

PubMed

Liu, Zhiwei; Li, Mingzhe; Han, Qigang; Yang, Yunfei; Wang, Bolong; Sui, Zhou

2013-05-01

A novel ultra-high pressure device, multilayer stagger-split die, has been constructed based on the principle of "dividing dies before cracking." Multilayer stagger-split die includes an encircling ring and multilayer assemblages, and the mating surfaces of the multilayer assemblages are mutually staggered between adjacent layers. In this paper, we investigated the stressing features of this structure through finite element techniques, and the results were compared with those of the belt type die and single split die. The contrast experiments were also carried out to test the bearing pressure performance of multilayer stagger-split die. It is concluded that the stress distributions are reasonable and the materials are utilized effectively for multilayer stagger-split die. And experiments indicate that the multilayer stagger-split die can bear the greatest pressure.

Euthanasia, assisted dying and the right to die in Ghana: a socio-legal analysis.

PubMed

Owusu-Dapaa, Ernest

2013-12-01

There is unanimity among states to protect the continuation of life of the individual as a safeguard against their collective extinction. The right to life is accordingly guaranteed but its antithesis, the right to die is the subject of an unending debate. The controversy over the right to die is deepened by rapid advances in medicine, creating the capability for prolongation of life beyond the span which one's natural strength can endure. Ghana's supreme law explicitly guarantees the right to life but remains ambiguous on right to die, particularly euthanasia and assisted dying. Thus, some of the other rights, such as the right to dignity and not to be tortured, can creatively be exploited to justify some instances of euthanasia. Ghana's criminal code largely proscribes euthanasia. Notwithstanding, proscription of euthanasia and assisted dying by the law, in Ghana's empirical work undertaken in some of the communities in Ghana, suggests that euthanasia is quietly practisedin health facilities and private homes, especially in the rural areas. Contrary to the popular reasons assigned in the literature of the Western world, with respect to the practice or quest for legalization of euthanasia as being a necessity for providing relief from pain or hopeless quality of life, empirical data from social and anthropological studies conducted in Ghana reveal that poverty is the motivation for informal euthanasia practice in Ghana rather than genuine desire on part of patients to die or their relatives to see to their accelerated death. Apart from poverty, traditional cultural values of African societies consider non-natural death as a taboo and ignominy to the victim and his family. Thus, any move by the government to legalize euthanasia will need to be informed by widely held consultations and a possible referendum; otherwise the law may be just a mere transplant of Western models of legislation on euthanasia without reflecting the ethos of the African people.

Soil nutrient bioavailability and nutrient content of pine trees (Pinus thunbergii) in areas impacted by acid deposition in Korea.

PubMed

Yang, Jae E; Lee, Wi-Young; Ok, Yong Sik; Skousen, Jeffrey

2009-10-01

Acid deposition has caused detrimental effects on tree growth near industrial areas of the world. Preliminary work has indicated that concentrations of NO(3-), SO(4)(2-), F( - ) and Al in soil solutions were 2 to 33 times higher in industrial areas compared to non-industrial areas in Korea. This study evaluated soil nutrient bioavailability and nutrient contents of red pine (Pinus thunbergii) needles in forest soils of industrial and non-industrial areas of Korea. Results confirm that forest soils of industrial areas have been acidified mainly by deposition of sulfate, resulting in increases of Al, Fe and Mn and decreases of Ca, Mg and K concentrations in soils and soil solutions. In soils of industrial areas, the molar ratios of Ca/Al and Mg/Al in forest soils were <2, which can lead to lower levels and availability of nutrients for tree growth. The Ca/Al molar ratio of Pinus thunbergii needles on non-industrial sites was 15, while that of industrial areas was 10. Magnesium concentrations in needles of Pinus thunbergii were lower in soils of industrial areas and the high levels of acid cations such as Al and Mn in these soils may have antagonized the uptake of base cations like Mg. Continued acidification can further reduce uptake of base cations by trees. Results show that Mg deficiency and high concentrations of Al and Mn in soil solution can be limiting factors for Pinus thunbergii growth in industrial areas of Korea.

Digital modeling of end-mill cutting tools for FEM applications from the active cutting contour

NASA Astrophysics Data System (ADS)

Salguero, Jorge; Marcos, M.; Batista, M.; Gómez, A.; Mayuet, P.; Bienvenido, R.

2012-04-01

A very current technique in the research field of machining by material removal is the use of simulations using the Finite Element Method (FEM). Nevertheless, and although is widely used in processes that allows approximations to orthogonal cutting, such as shaping, is scarcely used in more complexes processes, such as milling. This fact is due principally to the complex geometry of the cutting tools in these processes, and the need to realize the studi es in an oblique cutting configuration. This paper shows a methodology for the geometrical characterization of commercial endmill cutting tools, by the extraction of the cutting tool contour, making use of optical metrology, and using this geometry to model the active cutting zone with a 3D CAD software. This model is easily exportable to different CAD formats, such as IGES or STEP, and importable from FEM software, where is possible to study the behavior in service of the same ones.

Sheet metal stamping die design for warm forming

DOEpatents

Ghosh, Amit K.

2003-04-22

In metal stamping dies, by taking advantage of improved material flow by selectively warming the die, flat sections of the die can contribute to the flow of material throughout the workpiece. Local surface heating can be accomplished by placing a heating block in the die. Distribution of heating at the flat lower train central regions outside of the bend region allows a softer flow at a lower stress to enable material flow into the thinner, higher strain areas at the bend/s. The heating block is inserted into the die and is powered by a power supply.

Fast lichtschnell durch die Stadt: Visualisierung relativistischer Effekte

NASA Astrophysics Data System (ADS)

Kraus, Ute; Borchers, Marc P.

2005-03-01

Eine Computersimulation ermöglicht es uns, mit annähernd Lichtgeschwindigkeit durch die Tübinger Fußgängerzone zu fahren. Was wir dabei sehen, ist verblüffend: Die Häuser vor uns rücken umso weiter in die Ferne, je mehr wir beschleunigen; gleichzeitig erscheinen die Hauskanten in unserer Nähe immer stärker gekrümmt. Der Grund für diese merkwürdigen Bilder ist die so genannte Aberration: Ein und derselbe Lichtstrahl hat für den fahrenden Beobachter eine andere Richtung als für denjenigen, der am Straßenrand steht. Dieser Effekt ist im Alltag klein. Wenn wir aber in der Simulation fast lichtschnell durch die Tübinger Altstadt rasen, ist er dramatisch groß.

Fusarium spp. and Pinus strobus seedlings: root disease pathogens and taxa associated with seed

Treesearch

C. M. Ocamb; J. Juzwik; F. B. Martin

2002-01-01

Eastern white pine (Pinus strobus L .) seeds were sown in soil infested wlth Fusarium proliferatum, root necrosis developed on seedling roots, and F. proliferatum as reisolated from symptomatic roots; thus, demonstrating that F. proliferatum is pathogenic to eastern white pine seedling. Soils...

Assisted Dying in Canada.

PubMed

Schuklenk, Udo

This paper makes an affirmative ethical case in favour of the decriminalization of assisted dying in Canada. It then proceeds to defending the affirmative case against various slippery-slope arguments that are typically deployed by opponents of assisted dying. Finally, a recent case of questionable professional conduct by anti-euthanasia campaigners cum academics is flagged as a warning to all of us not to permit the quality of the professional debate to deteriorate unacceptably, despite the personal emotional investments involved on all sides of the debate.

Tubing and cable cutting tool

NASA Technical Reports Server (NTRS)

Mcsmith, D. D.; Richardson, J. I. (Inventor)

1984-01-01

A hand held hydraulic cutting tool was developed which is particularly useful in deactivating ejection seats in military aircraft rescue operations. The tool consists primarily of a hydraulic system composed of a fluid reservoir, a pumping piston, and an actuator piston. Mechanical cutting jaws are attached to the actuator piston rod. The hydraulic system is controlled by a pump handle. As the pump handle is operated the actuator piston rod is forced outward and thus the cutting jaws are forced together. The frame of the device is a flexible metal tubing which permits easy positioning of the tool cutting jaws in remote and normally inaccessible locations. Bifurcated cutting edges ensure removal of a section of the tubing or cable to thereby reduce the possibility of accidental reactivation of the tubing or cable being severed.

Exome genotyping, linkage disequilibrium and population structure in loblolly pine (Pinus taeda L.)

Treesearch

Mengmeng Lu; Konstantin V. Krutovsky; C. Dana Nelson; Tomasz E. Koralewski; Thomas D. Byram; Carol A. Loopstra

2016-01-01

Background: Loblolly pine (Pinus taeda L.) is one of the most widely planted and commercially important foresttree species in the USA and worldwide, and is an object of intense genomic research. However, whole genomeresequencing in loblolly pine is hampered by its large size and complexity and a lack of a good...

Galactoglucomannan Oligosaccharides (GGMO) from a Molasses Byproduct of Pine (Pinus taeda) Fiberboard Production

USDA-ARS?s Scientific Manuscript database

“Temulose” is the trade name for a water-soluble molasses produced on a large scale (300 - 400 tonnes per year) as a byproduct of the fiberboard industry. The feedstock for temulose is predominantly a single species of pine (Pinus taeda) grown and harvested in stands in southeastern Texas. Because...

Material properties and laser cutting of composites

NASA Astrophysics Data System (ADS)

Chen, Chia-Chieh; Cheng, Wing

Laser (Light Amplification by Stimulated Emission of Radiation) has been used successfully for many material cutting, drilling, metal welding and heat treating applications. However, laser cutting of polymer composites were attempted with varying degrees of success. Because composites are heterogeneous, the energy applied by laser could result in severe resin degradation before fibers were cut. In this study, cutting of glass, Kevlar, and graphite composites were evaluated based on their material properties and laser cutting parameters. A transient heat transfer analysis was used to determine the relative heat affected zones of these composites. Kevlar composites can be cut very well while graphite composites are difficult to cut. Though the cutting process is much more complicated in reality, the analysis provides a semi-quantitative perspective on the characteristics and limitations of laser cutting of different composites.

Influence of cutting parameters on the depth of subsurface deformed layer in nano-cutting process of single crystal copper.

PubMed

Wang, Quanlong; Bai, Qingshun; Chen, Jiaxuan; Su, Hao; Wang, Zhiguo; Xie, Wenkun

2015-12-01

Large-scale molecular dynamics simulation is performed to study the nano-cutting process of single crystal copper realized by single-point diamond cutting tool in this paper. The centro-symmetry parameter is adopted to characterize the subsurface deformed layers and the distribution and evolution of the subsurface defect structures. Three-dimensional visualization and measurement technology are used to measure the depth of the subsurface deformed layers. The influence of cutting speed, cutting depth, cutting direction, and crystallographic orientation on the depth of subsurface deformed layers is systematically investigated. The results show that a lot of defect structures are formed in the subsurface of workpiece during nano-cutting process, for instance, stair-rod dislocations, stacking fault tetrahedron, atomic clusters, vacancy defects, point defects. In the process of nano-cutting, the depth of subsurface deformed layers increases with the cutting distance at the beginning, then decreases at stable cutting process, and basically remains unchanged when the cutting distance reaches up to 24 nm. The depth of subsurface deformed layers decreases with the increase in cutting speed between 50 and 300 m/s. The depth of subsurface deformed layer increases with cutting depth, proportionally, and basically remains unchanged when the cutting depth reaches over 6 nm.

A clinical perspective on dying

PubMed Central

Janes, Robert G.

1972-01-01

There is continuing need for dissemination of already available, clinically useful knowledge concerning the psychological needs of the seriously ill and dying. Against the changing social context of dying, some of our erroneous assumptions about these patients are explored and the genuine fears and personal needs are discussed. The implications of this knowledge for medical education are recognized. PMID:5074753

36 CFR 910.57 - Curb-cut.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Curb-cut. 910.57 Section 910... DEVELOPMENT AREA Glossary of Terms § 910.57 Curb-cut. Curb-cut means that portion of the curb and sidewalk over which vehicular access is allowed. The number of access lanes for each curb-cut shall be specified...

First report of two cone and seed insects on Pinus flexilis

Treesearch

Anna Schoettle; Jose Negron

2001-01-01

Limber pine (Pinus flexilis James) ranges in latitude from 33°N to 51°N and in elevation from 870 m above sea level (asl) in North Dakota to ~3400 m asl in Colorado (Burns and Honkala 1990). In the central Rocky Mountains, limber pine co-occurs with many tree species due to its broad elevational range (Peet 1981). Limber pine seeds are large, generally...

Historical review of die drool phenomenon during plastics extrusion

NASA Astrophysics Data System (ADS)

Musil, Jan; Zatloukal, Martin

2013-04-01

Die drool phenomenon is defined as unwanted spontaneous accumulation of extruded polymer melt on open faces of extrusion die during extrusion process. Such accumulated material builds up on the die exit and frequently or continually sticks onto the extruded product and thus damages it. Since die drool appears, extrusion process must be shut down and die exit must be manually cleaned which is time and money consuming. Although die drool is complex phenomenon and its formation mechanism is not fully understood yet, variety of proposed explanations of its formation mechanism and also many ways to its elimination can be found in open literature. Our review presents in historical order breakthrough works in the field of die drool research, shows many ways to suppress it, introduces methods for its quantitative evaluation and composition analysis and summarizes theories of die drool formation mechanism which can be helpful for extrusion experts.

CUTTING AND WEDGING JACKET REMOVER

DOEpatents

Freedman, M.; Raynor, S.

1959-04-01

A tool is presented for stripping cladded jackets from fissionable fuel elements. The tool is a tube which fits closely around the jacket and which has two cutting edges at opposite sides of one end. These cutting edges are adjusted to penetrate only the jacket so that by moving the edges downward the jacket is cut into two pieces.

The Dying Role: Its Relevance to Improved Patient Care.

PubMed

Noyes, Russell; Clancy, John

2016-01-01

SOCIETY is failing to meet the obligation it has to its dying members. Persons with terminal illnesses suffer isolation and neglect in hospitals, receive overzealous treatment by physicians, and are kept in ignorance of their situation by families and medical personnel. Evidence for these statements has come from observers of the medical care system and from dying patients themselves (Kübler-Ross, 1969; Reynolds and Kalish, 1974; Sudnow, 1967). In the nineteenth century it was common for persons to die in the familiar environs of their homes, surrounded by grieving families from whom they parted in a meaningful manner (Blauner, 1966). Dying persons of today no longer fill a well-defined social role. Instead, the distinction between the roles of sick and dying persons has been lost and, in the resulting confusion, the care of dying people has suffered. The purpose of this article is to clarify the distinction between the dying and sick roles, identify the signs of existing role confusion, suggest ways in which this confusion may be corrected, and show how reestablishment of the dying role can result in improved care of dying people. The important part physicians play in defining sick and dying roles will be emphasized.

ECTOMYCORRHIZAL DIVERSITY IN A LOBLOLLY PINE (PINUS TAEDA L.) GENETICS PLANTATION: INFLUENCE OF FERTILIZATION

EPA Science Inventory

Loblolly pine (Pinus taeda L.) Has co-evolved a high dependency on ectomycorrhizal (ECM) associations most likely because its natural range includes soils of varying moisture that are P- and/or N-deficient. Because of its wide geographic distrubition, we would expect its roots t...

EFFECTS OF CARBON DIOXIDE AND OZONE ON GROWTH AND BIOMASS ALLOCATION IN PINUS PONDEROSA

EPA Science Inventory

The future productivity of forests will be affected by combinations of elevated atmospheric CO2 and O3. Because productivity of forests will, in part, be determined by growth of young trees, we evaluated shoot growth and biomass responses of Pinus ponderosa seedlings exposed to ...

Alkanes and terpenes in wood and leaves of Pinus jeffreyi and P. sabiniana

Treesearch

Robert P. Adams; Jessica W. Wright

2012-01-01

The wood oils of Pinus jeffreyi and P. sabiniana contain considerable amounts of heptane (76.6%, 92%), on a monoterpene basis. However, when entire wood extractables is considered, the amounts drop considerably (3.4%, 36.8%) with the major portion of the wood oils being diterpene acids. The leaf oil of P. jeffreyi...

Effects of air pollution on morphological and anatomical characteristics of Pinus Eldarica Wood

Treesearch

Vahidreza Safdari; Moinuddin Ahmed; Margaret S. Devall; Vilma Bayramzadeh

2012-01-01

Air pollution, including automobile exhaust pollution, can affect anatomical and morphological characteristics of wood. In order to evaluate this subject, the Pinus eldarica trees of Chitgar Park in Tehran, which extends from a crowded highway in the south (polluted site) to the semi polluted midsection and to Alborz Mountain in the north (unpolluted...

Regeneration Methods Affect Genetic Variation and Structure in Shortleaf Pine (Pinus Echinata Mill.)

Treesearch

Rajiv G. Raja; Charles G. Tauer; Robert F. Wittwer; Yinghua Huang

1998-01-01

The effects of regene ration methods on genetic diversity and structure in shortleaf pine (Pinus echinata Mill.) were examined by quantifying the changes in genetic composition of shortleaf pine stands following harvest by monitoring changes in allele number and frequency at heterozygous loci over time. The results were also compared to the genetic...

Polyamine levels during the development of zygotic and somatic embryos of Pinus radiata

Treesearch

Rakesh Minocha; Dale R. Smith; Cathie Reeves; Kevin D. Steele; Subhash C. Minocha

1999-01-01

Changes in the cellular content of three polyamines (putrescine, spermidine and spermine) were compared at different stages of development in zygotic and somatic embryos of Pinus radiata D. Don. During embryo development, both the zygotic and the somatic embryos showed a steady increase in spermidine content, with either a small decrease or no...

Laser Cutting of Multilayered Kevlar Plates

NASA Astrophysics Data System (ADS)

Yilbas, B. S.; Al-Sulaiman, F.; Karakas, C.; Ahsan, M.

2007-12-01

Laser cutting of Kevlar plates, consisting of multilayered laminates, with different thicknesses are carried out. A mathematical model is developed to predict the kerf width, thermal efficiency, and specific energy requirements during cutting. Optical microscopy and Scanning Electron Microscopy (SEM) are employed to obtain the micrographs of the cutting sections. The kerf width size is measured and compared with the predictions. A factorial analysis is carried out to assess the affecting parameters on the mean kerf width and dimensionless damage sizes. It is found that the kerf width and damage sizes changes sharply when increasing cutting speed from 0.03 to 0.08 m/s. Thermal efficiency of the cutting process increases with increasing thickness and cutting speed while specific energy reduces with increasing thickness. The main effects of cutting parameters are found to be significant on the mean kerf width and dimensionless damage sizes, which is more pronounced for the workpiece bottom surface, where locally distributed char formation and sideways burning are observed.

'Bridging worlds': meeting the emotional needs of dying patients.

PubMed

Law, Rollanda

2009-12-01

This paper is a report of a study to develop a grounded theory to explain how district nurses meet the emotional needs of dying patients in the community. There has been a policy commitment internationally to improve community services and enable people with terminal illnesses to die in their own homes. This increasing trend towards home deaths in the United Kingdom (UK) makes more demand on district nurses to provide emotional support for dying patients. A 'classic' grounded theory study was conducted in the UK between 2002 and 2005. Unstructured observations and semi-structured interviews were conducted with a purposive sample of nine district nurses, nine patients and four family carers. A further theoretical sample of five books of authors' accounts of their dying experiences and three district nurses who were advanced practitioners were selected. Five categories were identified in the data: 'outside world', 'dying world', 'entering dying world', 'maintaining connections' and the core category 'bridging worlds'. The theory of 'bridging worlds' indicated that dying patients experienced 'dying world' and 'outside world'. District nurses met dying patients' emotional needs by acting as a bridge between their two worlds, encouraging them to maintain connections with the outside world so that they did not become isolated in their dying world. District nurses should ensure that they meet both the physical and emotional needs of dying patients. Nursing education and literature need to concentrate on raising awareness of nurses' role in providing emotional support.

De-tabooing dying control - a grounded theory study

PubMed Central

2013-01-01

Background Dying is inescapable yet remains a neglected issue in modern health care. The research question in this study was “what is going on in the field of dying today?” What emerged was to eventually present a grounded theory of control of dying focusing specifically on how people react in relation to issues about euthanasia and physician-assisted suicide (PAS). Methods Classic grounded theory was used to analyze interviews with 55 laypersons and health care professionals in North America and Europe, surveys on attitudes to PAS among physicians and the Swedish general public, and scientific literature, North American discussion forum websites, and news sites. Results Open awareness of the nature and timing of a patient’s death became common in health care during the 1960s in the Western world. Open dying awareness contexts can be seen as the start of a weakening of a taboo towards controlled dying called de-tabooing. The growth of the hospice movement and palliative care, but also the legalization of euthanasia and PAS in the Benelux countries, and PAS in Montana, Oregon and Washington further represents de-tabooing dying control. An attitude positioning between the taboo of dying control and a growing taboo against questioning patient autonomy and self-determination called de-paternalizing is another aspect of de-tabooing. When confronted with a taboo, people first react emotionally based on “gut feelings” - emotional positioning. This is followed by reasoning and label wrestling using euphemisms and dysphemisms - reflective positioning. Rarely is de-tabooing unconditional but enabled by stipulated positioning as in soft laws (palliative care guidelines) and hard laws (euthanasia/PAS legislation). From a global perspective three shapes of dying control emerge. First, suboptimal palliative care in closed awareness contexts seen in Asian, Islamic and Latin cultures, called closed dying. Second, palliative care and sedation therapy, but not euthanasia

Changes in the cutting efficiency of different types of dental diamond rotary instrument with repeated cuts and disinfection.

PubMed

Bae, Jin-Hyuk; Yi, Jaeyoung; Kim, Sungtae; Shim, June-Sung; Lee, Keun-Woo

2014-01-01

Cutting efficiency is one of the most important factors to consider when a specific dental diamond rotary instrument is selected. However, the selection of a dental diamond rotary instrument is based on clinical experience rather than any scientific evidence. The purpose of this study was to identify how the cutting efficiency of different types of dental diamond rotary instrument changed with repeated cuts and disinfection. Four types of diamond rotary instrument from 2 dental manufacturers (Shofu, Jin Dental) were investigated with a high-speed air-turbine handpiece. The groups were as follows: S cham group (n=10): chamfer design from Shofu; J cham group (n=10): chamfer design from Jin Dental; S thin group (n=10): thin tapered design from Shofu; J thin group (n=10): thin tapered design from Jin Dental. Changes in the cutting efficiency of diamond rotary instruments on glass ceramic blocks were measured after repeated cuts. Changes in cutting efficiency also were measured for 30 diamond rotary instruments, the same type as those used in group J cham after disinfection with ethylene oxide gas, immersion in solution, or autoclaving. One-way ANOVA, 2-way ANOVA, and repeated-measures ANOVA were used to identify differences in cutting efficiency, in total cutting efficiency, and change trend in cutting efficiency (α=.05). The Tukey honestly significant difference method was used for the post hoc tests. The principal metal components of the diamond rotary instruments were detected with x-ray spectrometry. The mean (standard deviation [SD]) total cutting efficiency after 10 cuts in the 4 groups was in the following order: J cham group (0.210 ± 0.064 g/min) > S cham group (0.170 ± 0.064 g/min) > J thin group (0.130 ± 0.042 g/min) > S thin group (0.010 ± 0.040 g/min) (P<.05).The decrease in the cutting efficiency was greatest after the first cut. The cutting efficiency was not influenced by repeated disinfection. The cutting efficiencies of diamond rotary instruments

Net production relations of three tree species at Oak Ridge, Tennessee. [Liriodendron tulipifera; Quercus alba; Pinus echinata

DOE Office of Scientific and Technical Information (OSTI.GOV)

Whittaker, R.H.; Cohen, N.; Olson, J.S.

Measurement of productivity of forests is a difficult problem which has been variously approached. Results from an exploratory application of one approach (Whittaker 1961) to trees of three species - Liriodendron tulipifera (tulip tree or yellow poplar), Quercus alba (white oak), and Pinus echinata (shortleaf pine) - are reported here. The trees were felled in a logging operation at Oak Ridge National Laboratory in a mature second-growth, mixed oak-pine forest including also Quercus velutina, Q. coccinea, Q. falcata, Pinus virginiana, Acer rubrum, Nyssa sylvatica, Oxydendrum arboreum, and Carya ovalis. The forest grew on slopes of low hills on Knox dolomitemore » at about 300 m elevation. 22 references, 1 figure, 2 tables.« less

Diamond tool wear detection method using cutting force and its power spectrum analysis in ultra-precision fly cutting

NASA Astrophysics Data System (ADS)

Zhang, G. Q.; To, S.

2014-08-01

Cutting force and its power spectrum analysis was thought to be an effective method monitoring tool wear in many cutting processes and a significant body of research has been conducted on this research area. However, relative little similar research was found in ultra-precision fly cutting. In this paper, a group of experiments were carried out to investigate the cutting forces and its power spectrum characteristics under different tool wear stages. Result reveals that the cutting force increases with the progress of tool wear. The cutting force signals under different tool wear stages were analyzed using power spectrum analysis. The analysis indicates that a characteristic frequency does exist in the power spectrum of the cutting force, whose power spectral density increases with the increasing of tool wear level, this characteristic frequency could be adopted to monitor diamond tool wear in ultra-precision fly cutting.

ALPS yield optimization cutting program

Treesearch

P. Klinkhachorn; J.P. Franklin; Charles W. McMillin; H.A. Huber

1989-01-01

This paper reports ongoing work on a series of computer programs developed to automate hardwood lumber processing in a furniture roughmill. The program computes the placement of cuttings on lumber, based on a description of each board in terms of shape and defect location, and a cutting bill. These results are suitable for use with a high-power laser to cut the parts...

Phenolic compounds of Pinus laricio needles: a bioindicator of the effects of prescribed burning in function of season.

PubMed

Cannac, Magali; Pasqualini, Vanina; Barboni, Toussaint; Morandini, Frederic; Ferrat, Lila

2009-07-15

Fire is a dominant ecological factor in Mediterranean-type ecosystems. Forest management includes many preventive tools, in particular for fire prevention, such as mechanical treatments and prescribed burning. Prescribed burning is a commonly used method for treating fuel loads, but fuel reduction targets for reducing wildfire hazards must be balanced against fuel retention targets in order to maintain habitat and other forest functions. This approach was used on Pinus nigra ssp laricio var. Corsicana, a pine endemic to Corsica of great ecological and economic importance. Many studies of plant phenolic compounds have been carried out concerning responses to various stresses. The aim of this study was to understand i) the effects of prescribed burning 1 to 16 months later and ii) the effects of the seasonality of burning, spring or fall, on the production of phenolic compounds in Pinus laricio. After prescribed burning conducted in spring, Pinus laricio increases the synthesis of total phenolic compounds for a period of 7 months. The increase is greater after spring-burning than fall-burning. With regard to simple phenols, only dihydroferulic acid responds about 1 year after both types of prescribed burning. The causes of these increases are discussed in this paper. Total phenolic compounds could be used as a bioindicator for the short-term response of Pinus laricio needles to prescribed burning. Simple phenols may be useful for revealing the medium-term effects of prescribed burning. The results of this study include recommending forest managers to use prescribed burning in the fall rather than spring to reduce fuel loads and have less impact on the trees.

Corner-cutting mining assembly

DOEpatents

Bradley, John A.

1983-01-01

A mining assembly includes a primary rotary cutter mounted on one end of a support shaft and four secondary rotary cutters carried on the same support shaft and positioned behind the primary cutters for cutting corners in the hole cut by the latter.

Laser cutting system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dougherty, Thomas J

A workpiece cutting apparatus includes a laser source, a first suction system, and a first finger configured to guide a workpiece as it moves past the laser source. The first finger includes a first end provided adjacent a point where a laser from the laser source cuts the workpiece, and the first end of the first finger includes an aperture in fluid communication with the first suction system.

Acting to let someone die.

PubMed

McGee, Andrew

2015-02-01

This paper examines the recent prominent view in medical ethics that withdrawing life-sustaining treatment (LST) is an act of killing. I trace this view to the rejection of the traditional claim that withdrawing LST is an omission rather than an act. Although that traditional claim is not as problematic as this recent prominent view suggests, my main claim is that even if we accepted that withdrawing LST should be classified as an act rather than as an omission, it could still be classified as letting die rather than killing. Even though omissions are contrasted with acts, letting die need not be, for one can let die by means of acts. The remainder of the paper is devoted to establishing this claim and addresses certain objections to it. © 2013 John Wiley & Sons Ltd.

Computer aided system for parametric design of combination die

NASA Astrophysics Data System (ADS)

Naranje, Vishal G.; Hussein, H. M. A.; Kumar, S.

2017-09-01

In this paper, a computer aided system for parametric design of combination dies is presented. The system is developed using knowledge based system technique of artificial intelligence. The system is capable to design combination dies for production of sheet metal parts having punching and cupping operations. The system is coded in Visual Basic and interfaced with AutoCAD software. The low cost of the proposed system will help die designers of small and medium scale sheet metal industries for design of combination dies for similar type of products. The proposed system is capable to reduce design time and efforts of die designers for design of combination dies.

Automated Laser Cutting In Three Dimensions

NASA Technical Reports Server (NTRS)

Bird, Lisa T.; Yvanovich, Mark A.; Angell, Terry R.; Bishop, Patricia J.; Dai, Weimin; Dobbs, Robert D.; He, Mingli; Minardi, Antonio; Shelton, Bret A.

1995-01-01

Computer-controlled machine-tool system uses laser beam assisted by directed flow of air to cut refractory materials into complex three-dimensional shapes. Velocity, position, and angle of cut varied. In original application, materials in question were thermally insulating thick blankets and tiles used on space shuttle. System shapes tile to concave or convex contours and cuts beveled edges on blanket, without cutting through outer layer of quartz fabric part of blanket. For safety, system entirely enclosed to prevent escape of laser energy. No dust generated during cutting operation - all material vaporized; larger solid chips dislodged from workpiece easily removed later.

Composition and Bioactivity of Lipophilic Metabolites from Needles and Twigs of Korean and Siberian Pines (Pinus koraiensis Siebold & Zucc. and Pinus sibirica Du Tour).

PubMed

Shpatov, Alexander V; Popov, Sergey A; Salnikova, Olga I; Kukina, Tatyana P; Shmidt, Emma N; Um, Byung Hun

2017-02-01

Lipophilic extractive metabolites in different parts of the shoot system (needles and defoliated twigs) of Korean pine, Pinus koraiensis, and Siberian pine, Pinus sibirica, were studied by GC/MS. Korean pine needles comprised mainly bornyl p-coumarate, heterocyclic 15-O-functionalized labdane type acids (lambertianic acid), 10-nonacosanol, sterols and their esters. While Siberian pine needles contained less bornyl p-coumarate, lambertianic acid, sterols and their esters, but were richer in other 15-O-functionalized labdane type acids. The major components of the twig extract of P. koraiensis were lambertianic acid, abietane and isopimarane type acids, cembrane type alcohols, 8-O-functionalized labdanoids, sterols, sterol esters, and acylglycerols. The same extract of P. sibirica differed in larger amounts of other 15-O-functionalized labdane type acids and pinolenic acid glycerides, but in less quantities of cembranoids and 8-O-functionalized labdanoids. The labdane type pinusolic acid was detected for the first time in Korean pine. P. koraiensis was found to be unique in the genus for an ability to synthesize phyllocladane diterpenoids. The content of bound Δ 5 -unsaturated polymethylene-interrupted fatty acids in the twig extracts of the both pines was similar or superior to that in their seed oil. Among the pines' metabolites tested isocembrol was strongest in inhibition of both α-glucosidase (IC 50 2.9 μg/ml) and NO production in activated macrophages (IC 50 3.6 μg/ml). © 2017 Wiley-VHCA AG, Zurich, Switzerland.

Impact of Pinus Afforestation on Soil Chemical Attributes and Organic Matter in South Brazilian highlands

NASA Astrophysics Data System (ADS)

Pinheiro Dick, D.; Benvenuti Leite, S.; Dalmolin, R.; Almeida, H.; Knicker, H.; Martinazzo, R.

2009-04-01

The region known as Campos de Cima da Serra, located at 800 to 1400 m above sea level in the northeas of Rio Grande do Sul State, Brazil, is covered by a mosaic of natural grassland and Araucaria forest. Cattle raising, introduced by the first European settlers about 200 years ago, is the traditional economic activity in the region, occurring extensively and continuously on the natural pasture. In the last 30 years, while seeking for higher profits, local farmers have introduced agricultural crops and Pinus Taeda plantations in the original pasture lands. Pinus plantations are established in this area as dense monocultures and not as a sylvipastoral system, representing, thus, a severe threaten to the Campos' biodiversity. The soils are shallow, though very acidic (pH 4.2) and rich in exchangeable Al (28 to 47% of Al saturation), and present high contents of SOM in the surface layer (in general, higher than 4 %), which shows a low decomposition degree, as indicated by its high proportion of C-O alkyl groups (51 to 59 %). Considering that the biome sustainability of this region is being progressively affected by the change of land use and that systematic studies about exotic trees afforestation in that region are very scarce, our main objective was to investigate the impact of the introduction of Pinus on the SOM composition and chemical attributes of highland soils in 8 (Pi8) and 30 (Pi30) years old plantations, using as reference the original condition under native pasture (NP). In each studied Leptosol, soil samples were collected from three layers down to 15 cm ( 0-5 cm, 5-10 cm and 10-15 cm). Contents of exchangeable cations and of micronutrients and soil pH were determined. The SOM composition was investigated by means of elemental analyses, FTIR and fluorescence spectroscopy (three replicates). Prior to the spectroscopic analyses, samples were demineralized with 10% HF solution and organic matter loss was monitored. From the FTIR spectra, an aromaticity index

Starting Trees from Cuttings.

ERIC Educational Resources Information Center

Kramer, David C.

1983-01-01

Describes a procedure for starting tree cuttings from woody plants, explaining "lag time," recommending materials, and giving step-by-step instructions for rooting and planting. Points out species which are likely candidates for cuttings and provides tips for teachers for developing a unit. (JM)

Pinus Taeda L. response to fertilization, Herbaceous plant control, and woody plant control

Treesearch

Allan E. Tiarks; James D. Haywood

1986-01-01

On an intensively prepared site, a complete fertilizer applied at planting, and control of herbaceous and woody plants for the first 4 years, increased Pinus taeda L. volume at age 5 to 25.9 m3/ha compared to 11.8 m3/ha without the treatments. The fertilizer and competition control factors affected pine...

Comparison of Accuracy between Side-Cutting Instruments and Front-Cutting Instruments in Minimally Invasive Total Knee Arthroplasty.

PubMed

Pinsornsak, Piya; Harnroongroj, Thos

2016-11-01

The specialized instrument system used in minimally invasive surgery (MIS) has been developed for reducing soft tissue trauma in total knee arthroplasty (TKA). Compared with front-cutting MIS instruments, side-cutting quadriceps sparing MIS instruments have the advantage of creating a smaller incision and causing fewer traumas to the quadriceps tendon. However, the accuracy of side-cutting instruments concerns surgeons in prosthesis malalignment. To compare the accuracy of side-cutting quadriceps sparing instruments versus front-cutting instruments in MIS-TKA. In this prospective randomized controlled study, we compared the accuracy of side-cutting quadriceps sparing instruments versus the front-cutting instruments used in MIS-TKA. Sixty knees were included in the study, with 30 knees in each group. All the operations were performed by single surgeon. Coronal alignment (tibiofemoral angle, lateral distal femoral angle, and medial proximal tibial angle), and sagittal alignment (femoral component flexion and tibial posterior slope) were measured and compared. Tibiofemoral angle, lateral distal femoral angle, and medial proximal tibial angle, all of which are considered in the assessment of acceptable coronal radiographic alignment, were not different between groups (p = 0.353, 0.500, and 0.177, respectively). However, side-cutting quadriceps sparing instruments produced less acceptable sagittal radiographic alignment, femoral component flexion (63% vs. 93%, p = 0.005), and tibial posterior slope (73% vs. 93%, p = 0.04). Side-cutting quadriceps sparing MIS-TKA instruments had similar accuracy to front-cutting MIS-TKA instruments for coronal alignment but is less accurate for sagittal alignment.

REFRACTORY DIE FOR EXTRUDING URANIUM

DOEpatents

Creutz, E.C.

1959-08-11

A die is presented for the extrusion of metals, said die being formed of a refractory complex oxide having the composition M/sub n/O/sub m/R/sub x/O/sub y/ where M is magnesium, zinc, manganese, or iron, R is aluminum, chromic chromium, ferric iron, or manganic manganese, and m, n, x, and y are whole numbers. Specific examples are spinel, magnesium aluminate, magnetite, magnesioferrite, chromite, and franklinite.

WATER-USE ALONG A HYDROLOGICAL GRADIENT IN CENTRAL FLORIDA: A TALE OF TWO PINUS SPECIES

EPA Science Inventory

Although central Florida is relatively flat, the distribution of species on the landscape is controlled by subtle changes in elevation. Along a four-meter elevation gradient, xeric sandhill vegetation dominated by Pinus palustris (Longleaf pine) gives way to mesic pine flatwoods...

Comparative study of 0° X-cut and Y + 36°-cut lithium niobate high-voltage sensing

NASA Astrophysics Data System (ADS)

Patel, N.; Branch, D. W.; Schamiloglu, E.; Cular, S.

2015-08-01

A comparison study between Y + 36° and 0° X-cut lithium niobate (LiNbO3) was performed to evaluate the influence of crystal cut on the acoustic propagation to realize a piezoelectric high-voltage sensor. The acoustic time-of-flight for each crystal cut was measured when applying direct current (DC), alternating current (AC), and pulsed voltages. Results show that the voltage-induced shift in the acoustic wave propagation time scaled quadratically with voltage for DC and AC voltages applied to X-cut crystals. For the Y + 36° crystal, the voltage-induced shift scales linearly with DC voltages and quadratically with AC voltages. When applying 5 μs voltage pulses to both crystals, the voltage-induced shift scaled linearly with voltage. For the Y + 36° cut, the voltage-induced shift from applying DC voltages ranged from 10 to 54 ps and 35 to 778 ps for AC voltages at 640 V over the frequency range of 100 Hz-100 kHz. Using the same conditions as the Y + 36° cut, the 0° X-cut crystal sensed a shift of 10-273 ps for DC voltages and 189-813 ps for AC voltage application. For 5 μs voltage pulses, the 0° X-cut crystal sensed a voltage induced shift of 0.250-2 ns and the Y + 36°-cut crystal sensed a time shift of 0.115-1.6 ns. This suggests a frequency sensitive response to voltage where the influence of the crystal cut was not a significant contributor under DC, AC, or pulsed voltage conditions. The measured DC data were compared to a 1-D impedance matrix model where the predicted incremental length changed as a function of voltage. When the voltage source error was eliminated through physical modeling from the uncertainty budget, the combined uncertainty of the sensor (within a 95% confidence interval) decreased to 0.0033% using a Y + 36°-cut crystal and 0.0032% using an X-cut crystal for all the voltage conditions used in this experiment.

Handpiece coolant flow rates and dental cutting.

PubMed

von Fraunhofer, J A; Siegel, S C; Feldman, S

2000-01-01

High-speed handpieces incorporate water coolant sprays to remove cutting debris and minimize thermal insult to the pulp. Little data exists on optimal coolant flow rates during clinical procedures. This study compared the effect of different coolant flow rates on diamond stone cutting efficiency. Cutting studies were performed on Macor machinable ceramic using a previously developed test regimen--a KaVo high-speed handpiece at a cutting force of 91.5 g (0.9 N). Cutting was performed with round end tapered medium grit diamond stones under cooling water flow rates of 15, 20, 25, 30 and 44 ml/min, with cutting rates determined as the time to transect the 13 mm square cross-section of the Macor bar. Each bur was used for five cuts, with six burs used for each flow rate, for a total of 150 measurements. The data were analyzed by one-way ANOVA with a post hoc Scheffé test. The cutting studies indicated that diamond stone cutting rates increased with higher coolant flow rates over the range of 15-44 ml/min. The data suggest that higher coolant flow rates promote cutting efficiency.

Cutting moments and grip forces in meat cutting operations and the effect of knife sharpness.

PubMed

McGorry, Raymond W; Dowd, Peter C; Dempsey, Patrick G

2003-07-01

The force exposure associated with meat cutting operations and the effect of knife sharpness on performance and productivity have not been well documented. Specialized hardware was used to measure grip force and reactive moments with 15 professional meat cutters performing lamb shoulder boning, beef rib trimming and beef loin trim operations in a field study conducted in two meat packing plants. A system for measuring relative blade sharpness was developed for this study. Mean and peak cutting moments observed for the meat cutting operations, averaged across subjects were 4.7 and 17.2 Nm for the shoulder boning, 3.5 and 12.9 Nm for the rib trim, and 2.3 and 10.6 Nm for the loin trim, respectively. Expressed as percent of MVC, mean grip forces of 28.3% and peak grip forces of 72.6% were observed overall. Blade sharpness was found to effect grip forces, cutting moments and cutting time, with sharper blades requiring statistically significantly lower peak and mean cutting moments, and grip forces than dull knives. Efforts aimed at providing and maintaining sharp blades could have a significant impact on force exposure.

A Contingency Framework for Listening to the Dying

ERIC Educational Resources Information Center

Vora, Erika; Vora, Ariana

2008-01-01

Listening to the dying poses special challenges. This paper proposes a contingency framework for describing and assessing various circumstances when listening to the dying. It identifies current approaches to listening, applies the contingency framework toward effectively listening to the dying, and proposes a new type of listening called…

Mosaic stunting in bareroot Pinus banksiana seedlings is unrelated to colonization by mycorrhizal fungi

Treesearch

Lynette R. Potvin; Martin F. Jurgensen; R. Kasten Dumroese; Dana L. Richter; Deborah S. Page-Dumroese

2014-01-01

Mosaic stunting, the occurrence of random patches of chlorotic seedlings with reduced shoot and diameter growth amidst more robust cohorts within bareroot nurseries, is classically associated with poor colonization by mycorrhizal fungi. We examined possible relationships among soil fertility, mycorrhizas, and random patches of mosaic stunting in bareroot Pinus...

Biomass distribution and productivity of Pinus edulis-Juniperus monosperma woodlands of north-central Arizona

Treesearch

Charles C. Grier; Katherine J. Elliott; Deborah G. McCullough

1992-01-01

Above-ground biomass distribution, leaf area, above-ground net primary productivity and foliage characteristics were determined for 90- and 350-year-old Pinus edulis-Juniperus monosperma ecosystems on the Colorado Plateau of northern Arizona. These ecosystems have low biomass, leaf area and primary productivity compared with forests in wetter...

Relationships between acoustic variables and different measures of stiffness in standing Pinus taeda trees

Treesearch

Christian R. Mora; Laurence R. Schimleck; Fikret Isik; Jerry M. Mahon Jr.; Alexander Clark III; Richard F. Daniels

2009-01-01

Acoustic tools are increasingly used to estimate standing-tree (dynamic) stiffness; however, such techniques overestimate static stiffness, the standard measurement for determining modulus of elasticity (MOE) of wood. This study aimed to identify correction methods for standing-tree estimates making dynamic and static stiffness comparable. Sixty Pinus taeda L...

Enclosed Cutting-And-Polishing Apparatus

NASA Technical Reports Server (NTRS)

Rossier, R. N.; Bicknell, B.

1989-01-01

Proposed apparatus cuts and polishes specimens while preventing contamination of outside environment or of subsequent specimens processed in it. Designed for use in zero gravity but also includes features useful in cutting and polishing of toxic or otherwise hazardous materials on Earth. Includes remote manipulator for handling specimens, cutting and polishing wire, inlets for gas and liquid, and outlets for waste liquid and gas. Replaceable plastic liner surrounds working space.

Economic technology of laser cutting

NASA Astrophysics Data System (ADS)

Fedin, Alexander V.; Shilov, Igor V.; Vassiliev, Vladimir V.; Malov, Dmitri V.; Peskov, Vladimir N.

2000-02-01

The laser cutting of color metals and alloys by a thickness more than 2 mm has significant difficulties due to high reflective ability and large thermal conduction. We made it possible to raise energy efficiency and quality of laser cutting by using a laser processing system (LPS) consisting both of the YAG:Nd laser with passive Q-switching on base of LiF:F2- crystals and the CO2 laser. A distinctive feature of the LPS is that the radiation of different lasers incorporated in a coaxial beam has simultaneously high level of peak power (more than 400 kW in a TEM00 mode) and significant level of average power (up to 800 W in a TEM01 mode of the CO2 laser). The application of combined radiation for cutting of an aluminum alloy of D16 type made it possible to decrease the cutting energy threshold in 1.7 times, to increase depth of treatment from 2 up to 4 mm, and velocity from 0.015 up to 0.7 m/min, and also to eliminate application of absorptive coatings. At cutting of steels the velocity of treatment was doubled, and also an oxygen flow was eliminated from the technological process and replaced by the air. The obtained raise of energy efficiency and quality of cutting is explained by an essential size reducing of a formed penetration channel and by the shifting of a thermal cutting mode from melting to evaporation. The evaluation of interaction efficiency of a combined radiation was produced on the basis of non-stationary thermal-hydrodynamic model of a heating source moving as in the cutting direction, and also into the depth of material.

Modeling future plant distributions on the Colorado Plateau: An example using Pinus edulis

Treesearch

Kenneth L. Cole; Kirsten E. Ironside; Samantha T. Arundel; Philip Duffy; John Shaw

2008-01-01

The recent mortality of some plant species in the U.S. Southwest has been attributed to the ongoing drought conditions over the last decade. This mortality has been especially acute in populations of Pinus edulis (Colorado pinyon pine; hereafter abbreviated as pinyon), a widespread and highly visible species (Shaw 2006; Shaw et al. 2005; Mueller et...

Viability of litter-stored Pinus taeda L. seeds after simulated prescribed winter burns

Treesearch

Michael D. Cain; Michael G. Shelton

1998-01-01

Stratified loblolly pine (Pinus taeda L.) seeds were placed at three depths in a reconstructed forest floor and subjected to simulated prescribed winter burns. Within the forest floor, pine seeds were placed at the L/upper-F interface, upper-F/lower-F interface, and lower-F/mineral-soil interface. Wind was generated by electric box-fans. Seeds that...

Patterns of resistance to Cronartium ribicola in Pinus aristata, Rocky Mountain bristlecone pine

Treesearch

A. W. Schoettle; R. A. Sniezko; A. Kegley; R. Danchok; K. S. Burns

2012-01-01

The core distribution of Rocky Mountain bristlecone pine, Pinus aristata Engelm., extends from central Colorado into northern New Mexico, with a disjunct population on the San Francisco Peaks in northern Arizona. Populations are primarily at high elevations and often define the alpine treeline; however, the species can also be found in open mixed conifer stands with...

Genetic diversity in longleaf pine (Pinus palustris): influence of historical and prehistorical events

Treesearch

Ronald C. Schmidtling; V. Hipkins

1998-01-01

Genetic diversity of allozymes at 24 loci was studied in 23 populations of longleaf pine (Pinus palustris Mill.), including three seed orchard populations and an old-growth stand. Overall, the mean number of alleles per polymorphic locus was 2.9, the percentage of polymorphic loci was 92 percent, and the mean expected heterozygosity was 0.105. These...

Water availability and genetic effects on wood properties of loblolly pine (Pinus taeda)

Treesearch

C. A. Gonzalez-Benecke; T. A. Martin; Alexander Clark; G. F. Peter

2010-01-01

We studied the effect of water availability on basal area growth and wood properties of 11-year-old loblolly pine (Pinus taeda L.) trees from contrasting Florida (FL) (a mix of half-sib families) and South Carolina coastal plain (SC) (a single, half-sib family) genetic material. Increasing soil water availability via irrigation increased average wholecore specific...

Evolutionary relationships among Pinus (Pinaceae) subsections inferred from multiple low-copy nuclear loci.

Treesearch

John Syring; Ann Willyard; Richard Cronn; Aaron Liston

2005-01-01

Sequence data from nrITS and cpDNA have failed to fully resolve phylogenetic relationships among Pinus species. Four low-copy nuclear genes, developed from the screening of 73 mapped conifer anchor loci, were sequenced from 12 species representing all subsections. Individual loci do not uniformly support either the nrITS or cpDNA hypotheses and in...

Genetic conservation and management of the Californian endemic, Torrey Pine (Pinus torreyana Parry)

Treesearch

Jill A. Hamilton; Jessica W. Wright; F. Thomas Ledig

2017-01-01

Torrey pine (Pinus torreyana) is one of the rarest pine species in the world. Restricted to one mainland and one island population in California, Torrey pine is a species of conservation concern under threat due to low population sizes, lack of genetic variation, and environmental stochasticity. Previous research points to a lack of within population variation that is...

13C discriminations of Pinus sylvestris vs. Pinus ponderosa at a dry site in Brandenburg (eastern Germany): 100-year growth comparison.

PubMed

Wagner, Ralf; Insinna, Patrick A; Götz, Bernhard; Junge, Sebastian; Boettger, Tatjana

2007-06-01

The carbon isotope composition (delta(13)C, per thousand) and discrimination (Delta, per thousand) of old grown North American Pinus ponderosa Dougl. Ex P. et C. Laws. and European Pinus sylvestris L. were determined using trees grown under almost identical growing conditions in a mixed stand in Bralitz, Northeast Germany. Single-tree delta(13)C analyses of tree-ring cellulose of both species were carried out at a yearly resolution for the period 1901-2001 and the results compared with growth (basal area increment). Annual mean delta(13)C values for P. ponderosa ranged from-21.6 per thousand to-25.2 per thousand and for P. sylvestris from-21.4 per thousand to-24.4 per thousand. Accordingly, (13)C discrimination (Delta) showed higher values for P. ponderosa throughout the investigation period. Five characteristic periods of Delta were identified for both the tree species, reflecting positive and negative influences of environmental factors. Good growing conditions such as after-thinning events had a positive effect on Delta, reflecting higher values, while poor conditions like aridity and air pollution had a negative influence, reflecting lower values. The dynamics of Delta were likewise reflected in the growth (basal area increment, BAI). Higher (13)C discrimination values of P. ponderosa led to higher BAIs of P. ponderosa in comparison with P. sylvestris. Correlation function analyses confirmed that P. sylvestris was more dependent on precipitation than P. ponderosa, which showed a closer relationship with temperature. The results confirm that under predominantly dry growing conditions, P. ponderosa showed better growth performance than P. sylvestris, indicating better common intrinsic water-use efficiency and, therefore, higher rates of net photosynthesis at a given transpiration. In view of the prospect of climate change, the results are very significant for assessing both trees' physiological properties and, hence, their potential for coping with future growing

Die nuklearen Anlagen von Hanford (1943-1987) Eine Fallstudie über die Schnittstellen von Physik, Biologie und die US-amerikanische Gesellschaft zur Zeit des Kalten Krieges

NASA Astrophysics Data System (ADS)

Macuglia, Daniele

Die Geschichte des Kalten Krieges eröffnet viele Möglichkeiten, sich näher mit den Schnittstellen von Physik und Biologie während des 20. Jahrhunderts zu befassen. Nicht nur das Unglück in Tschernobyl aus dem Jahr 1986, auch das Beispiel der nuklearen Anlagen in Hanford in den Vereinigten Staaten zeigt die biologischen Folgen von nuklearer Physik.

Effects of Cutting Edge Microgeometry on Residual Stress in Orthogonal Cutting of Inconel 718 by FEM.

PubMed

Shen, Qi; Liu, Zhanqiang; Hua, Yang; Zhao, Jinfu; Lv, Woyun; Mohsan, Aziz Ul Hassan

2018-06-14

Service performance of components such as fatigue life are dramatically influenced by the machined surface and subsurface residual stresses. This paper aims at achieving a better understanding of the influence of cutting edge microgeometry on machined surface residual stresses during orthogonal dry cutting of Inconel 718. Numerical and experimental investigations have been conducted in this research. The cutting edge microgeometry factors of average cutting edge radius S¯, form-factor K , and chamfer were investigated. An increasing trend for the magnitudes of both tensile and compressive residual stresses was observed by using larger S¯ or introducing a chamfer on the cutting edges. The ploughing depth has been predicted based on the stagnation zone. The increase of ploughing depth means that more material was ironed on the workpiece subsurface, which resulted in an increase in the compressive residual stress. The thermal loads were leading factors that affected the surface tensile residual stress. For the unsymmetrical honed cutting edge with K = 2, the friction between tool and workpiece and tensile residual stress tended to be high, while for the unsymmetrical honed cutting edge with K = 0.5, the high ploughing depth led to a higher compressive residual stress. This paper provides guidance for regulating machine-induced residual stress by edge preparation.

Quantum Max-flow/Min-cut

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cui, Shawn X., E-mail: xingshan@math.ucsb.edu; Quantum Architectures and Computation Group, Microsoft Research, Redmond, Washington 98052; Freedman, Michael H., E-mail: michaelf@microsoft.com

2016-06-15

The classical max-flow min-cut theorem describes transport through certain idealized classical networks. We consider the quantum analog for tensor networks. By associating an integral capacity to each edge and a tensor to each vertex in a flow network, we can also interpret it as a tensor network and, more specifically, as a linear map from the input space to the output space. The quantum max-flow is defined to be the maximal rank of this linear map over all choices of tensors. The quantum min-cut is defined to be the minimum product of the capacities of edges over all cuts ofmore » the tensor network. We show that unlike the classical case, the quantum max-flow=min-cut conjecture is not true in general. Under certain conditions, e.g., when the capacity on each edge is some power of a fixed integer, the quantum max-flow is proved to equal the quantum min-cut. However, concrete examples are also provided where the equality does not hold. We also found connections of quantum max-flow/min-cut with entropy of entanglement and the quantum satisfiability problem. We speculate that the phenomena revealed may be of interest both in spin systems in condensed matter and in quantum gravity.« less

Quantum Max-flow/Min-cut

NASA Astrophysics Data System (ADS)

Cui, Shawn X.; Freedman, Michael H.; Sattath, Or; Stong, Richard; Minton, Greg

2016-06-01

The classical max-flow min-cut theorem describes transport through certain idealized classical networks. We consider the quantum analog for tensor networks. By associating an integral capacity to each edge and a tensor to each vertex in a flow network, we can also interpret it as a tensor network and, more specifically, as a linear map from the input space to the output space. The quantum max-flow is defined to be the maximal rank of this linear map over all choices of tensors. The quantum min-cut is defined to be the minimum product of the capacities of edges over all cuts of the tensor network. We show that unlike the classical case, the quantum max-flow=min-cut conjecture is not true in general. Under certain conditions, e.g., when the capacity on each edge is some power of a fixed integer, the quantum max-flow is proved to equal the quantum min-cut. However, concrete examples are also provided where the equality does not hold. We also found connections of quantum max-flow/min-cut with entropy of entanglement and the quantum satisfiability problem. We speculate that the phenomena revealed may be of interest both in spin systems in condensed matter and in quantum gravity.

CARBON ISOTOPE DISCRIMINATION AND GROWTH RESPONSE OF OLD PINUS PONDEROSA TREES TO STAND DENSITY REDUCTIONS

EPA Science Inventory

Stand density reductions have been proposed as a method by which old-growth ponderosa pine (Pinus ponderosa) forests of North America can be converted back to pre-1900 conditions, thereby reducing the danger of catastrophic forest fires and insect attacks while increasing product...

CO2 AND O3 ALTER PHOTOSYNTHESIS AND WATER VAPOR EXCHANGE FOR PINUS PONDEROSA NEEDLES

EPA Science Inventory

1. Effects of CO2 and O3 were determined for a key component of ecosystem carbon and water cycling: needle gas exchange (photosynthesis, conductance, transpiration and water use efficiency). The measurements were made on Pinus ponderosa seedlings grown in outdoor, sunlit, mesoc...

Geographic patterns of genetic variation and population structure in Pinus aristata, Rocky Mountain bristlecone pine

USDA-ARS?s Scientific Manuscript database

Pinus aristata Engelm., Rocky Mountain bristlecone pine, has a narrow core geographic and elevational distribution, occurs in disjunct populations and is threatened by multiple stresses, including rapid climate change, white pine blister rust, and bark beetles. Knowledge of genetic diversity and pop...

Restoring Aristida stricta to Pinus palustris ecosystems on the Atlantic Coastal Plain, U.S.A.

Treesearch

Kenneth W. Outcalt; Marcus E. Williams; Oghenekome Onokpise

1999-01-01

Aristida stricta (wiregrass), a perennial bunchgrass, quickly accumulates dead leaves, which along with the shed needles of Pinus palustris (longleaf pine) provide the fuel for frequent surface fires. Thus, historically, wiregrass played a key role in many longleaf communities where it significantly...

Cutting Class Harms Grades

ERIC Educational Resources Information Center

Taylor, Lewis A., III

2012-01-01

An accessible business school population of undergraduate students was investigated in three independent, but related studies to determine effects on grades due to cutting class and failing to take advantage of optional reviews and study quizzes. It was hypothesized that cutting classes harms exam scores, attending preexam reviews helps exam…

Sodium-cutting: a new top-down approach to cut open nanostructures on nonplanar surfaces on a large scale.

PubMed

Chen, Wei; Deng, Da

2014-11-11

We report a new, low-cost and simple top-down approach, "sodium-cutting", to cut and open nanostructures deposited on a nonplanar surface on a large scale. The feasibility of sodium-cutting was demonstrated with the successfully cutting open of ∼100% carbon nanospheres into nanobowls on a large scale from Sn@C nanospheres for the first time.

Green Synthesis of Silver Nanoparticles using Extract of Pinus merkusii Jungh & De Vriese Cone Flower

NASA Astrophysics Data System (ADS)

Azkiya, N. I.; Masruri, M.; Ulfa, S. M.

2018-01-01

The paper studies recent application of cone flower waste from Pinus merkusii Jungh & De Vriese for an environmentally unclear method for synthesis silver nanoparticle. Phytochemical characterization using iron trichloride solution showed the extract of Pinus merkusii cone flower contains of phenolic group of secondary metabolite. This group acts as both reducing and stabilizing agents. For the synthesis of silver nanoparticle, solution of silver nitrate is added to the extract at 60°C. The effect of extract concentration (5-20%) and time reaction (15-60 min) is investigated. The formation of silver nanoparticle is confirmed by the color change from yellowish to brown. Meanwhile, UV-Vis characterization of silver nanoparticle in extract 20% and 60 min reaction showed surface plasmon resonance (SPR) at 431 nm, and transmission electron microscope (TEM) revealed the particle size range in between 8 and 23 nm with a spherical in shape.

Whitebark pine diameter growth response to removal of competition

Treesearch

Robert E. Keane; Kathy L. Gray; Laura J. Dickinson

2007-01-01

Silvicultural cutting treatments may be needed to restore whitebark pine (Pinus albicaulis) forests, but little is known of the response of this species to removal of competition through prescribed burning or silvicultural cuttings. We analyzed stem cross-sections from 48 whitebark pine trees in Montana around which most of the competing vegetation...

Effects of intermediate-severity disturbance on composition and structure in mixed Pinus-hardwood stands

Treesearch

Benjamin Trammell; Justin Hart; Callie Schweitzer; Daniel C. Dey; Michael Steinberg

2017-01-01

Increasingly, forest managers intend to create or maintain mixed Pinus-hardwood stands. This stand assemblage may be driven by a variety of objectives but is often motivated by the desire to enhance native forest diversity and promote resilience to perturbations. Documenting the effects of natural disturbances on species composition and stand...

Restoration planting options for limber pine (Pinus flexilis James) in the Southern Rocky Mountains

Treesearch

A. M. A. Casper; W. R. Jacobi; Anna Schoettle; K. S. Burns

2016-01-01

Limber pine Pinus flexilis James populations in the southern Rocky Mountains are threatened by the combined impacts of mountain pine beetles and white pine blister rust. To develop restoration planting methods, six P. flexilis seedling planting trial sites were installed along a geographic gradient from southern Wyoming to southern Colorado. Experimental...

Comparison of cutting efficiency with different diamond burs and water flow rates in cutting lithium disilicate glass ceramic.

PubMed

Siegel, Sharon C; Patel, Tejas

2016-10-01

This study compared different diamond burs and different water flow rates on the cutting efficiency of sectioning through lithium disilicate glass ceramic. The authors used a standardized cutting regimen with 4 brands of diamond burs to section through lithium disilicate glass ceramic blocks. Twelve diamonds of each brand cut through the blocks in randomized order. In the first part of the study, the authors recorded sectioning rates in millimeters per minute for each diamond bur as a measure of cutting efficiency. In the second part of the study, the authors compared sectioning rates using only 1 brand of diamond bur, with 3 different water flow rates. The authors averaged and compared cutting rates of each brand of diamond bur and the cutting rates for each flow rate using an analysis of variance and determined the differences with a Tukey honest significant difference test. One diamond bur cut significantly slower than the other 3, and one diamond bur cut significantly faster than 2 of the others. The diamond bur cutting efficiency through lithium disilicate glass ceramic with a 20 mL/min water flow rate was significantly higher than 15 mL/min. There are differences in cutting efficiency between diamond burs when sectioning lithium disilicate glass ceramic. Use a minimum of 20 mL/min of water coolant flow when sectioning lithium disilicate glass ceramic with dental diamond burs to maximize cutting efficiency. Recommendations for specific diamond burs with a coarse grit and water flow rate of 20 mL/min can be made when removing or adjusting restorations made from lithium disilicate glass ceramic. Copyright © 2016 American Dental Association. Published by Elsevier Inc. All rights reserved.

Comparative study of 0° X-cut and Y + 36°-cut lithium niobate high-voltage sensing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Patel, N.; Department of Electrical and Computer Engineering, MSC01 1100, University of New Mexico, Albuquerque, New Mexico 87131-0001; Branch, D. W.

2015-08-15

A comparison study between Y + 36° and 0° X-cut lithium niobate (LiNbO{sub 3}) was performed to evaluate the influence of crystal cut on the acoustic propagation to realize a piezoelectric high-voltage sensor. The acoustic time-of-flight for each crystal cut was measured when applying direct current (DC), alternating current (AC), and pulsed voltages. Results show that the voltage-induced shift in the acoustic wave propagation time scaled quadratically with voltage for DC and AC voltages applied to X-cut crystals. For the Y + 36° crystal, the voltage-induced shift scales linearly with DC voltages and quadratically with AC voltages. When applying 5more » μs voltage pulses to both crystals, the voltage-induced shift scaled linearly with voltage. For the Y + 36° cut, the voltage-induced shift from applying DC voltages ranged from 10 to 54 ps and 35 to 778 ps for AC voltages at 640 V over the frequency range of 100 Hz–100 kHz. Using the same conditions as the Y + 36° cut, the 0° X-cut crystal sensed a shift of 10–273 ps for DC voltages and 189–813 ps for AC voltage application. For 5 μs voltage pulses, the 0° X-cut crystal sensed a voltage induced shift of 0.250–2 ns and the Y + 36°-cut crystal sensed a time shift of 0.115–1.6 ns. This suggests a frequency sensitive response to voltage where the influence of the crystal cut was not a significant contributor under DC, AC, or pulsed voltage conditions. The measured DC data were compared to a 1-D impedance matrix model where the predicted incremental length changed as a function of voltage. When the voltage source error was eliminated through physical modeling from the uncertainty budget, the combined uncertainty of the sensor (within a 95% confidence interval) decreased to 0.0033% using a Y + 36°-cut crystal and 0.0032% using an X-cut crystal for all the voltage conditions used in this experiment.« less

Comparative study of 0° X-cut and Y+36°-cut lithium niobate high-voltage sensing

DOE PAGES

Patel, N.; Branch, D. W.; Schamiloglu, E.; ...

2015-08-11

A comparison study between Y+36° and 0° X-cut lithium niobate (LiNbO 3) was performed to evaluate the influence of crystal cut on the acoustic propagation to realize a piezoelectric high-voltage sensor. The acoustic time-of-flight for each crystal cut was measured when applying direct current (DC), alternating current (AC), and pulsed voltages. Results show that the voltage-induced shift in the acoustic wave propagation time scaled quadratically with voltage for DC and AC voltages applied to X-cut crystals. For the Y+36° crystal, the voltage-induced shift scales linearly with DC voltages and quadratically with AC voltages. When applying 5 μs voltage pulses tomore » both crystals, the voltage-induced shift scaled linearly with voltage. For the Y+36° cut, the voltage-induced shift from applying DC voltages ranged from 10 to 54 ps and 35 to 778 ps for AC voltages at 640 V over the frequency range of 100 Hz–100 kHz. Using the same conditions as the Y+36° cut, the 0° X-cut crystal sensed a shift of 10–273 ps for DC voltages and 189–813 ps for AC voltage application. For 5 μs voltage pulses, the 0° X-cut crystal sensed a voltage induced shift of 0.250–2 ns and the Y+36°-cut crystal sensed a time shift of 0.115–1.6 ns. This suggests a frequency sensitive response to voltage where the influence of the crystal cut was not a significant contributor under DC, AC, or pulsed voltage conditions. The measured DC data were compared to a 1-D impedance matrix model where the predicted incremental length changed as a function of voltage. Furthermore, when the voltage source error was eliminated through physical modeling from the uncertainty budget, the combined uncertainty of the sensor (within a 95% confidence interval) decreased to 0.0033% using a Y + 36°-cut crystal and 0.0032% using an X-cut crystal for all the voltage conditions used in this experiment.« less

Drought Tolerance in Pinus halepensis Seed Sources As Identified by Distinctive Physiological and Molecular Markers

PubMed Central

Taïbi, Khaled; del Campo, Antonio D.; Vilagrosa, Alberto; Bellés, José M.; López-Gresa, María Pilar; Pla, Davinia; Calvete, Juan J.; López-Nicolás, José M.; Mulet, José M.

2017-01-01

Drought is one of the main constraints determining forest species growth, survival and productivity, and therefore one of the main limitations for reforestation or afforestation. The aim of this study is to characterize the drought response at the physiological and molecular level of different Pinus halepensis (common name Aleppo pine) seed sources, previously characterized in field trials as drought-sensitive or drought-tolerant. This approach aims to identify different traits capable of predicting the ability of formerly uncharacterized seedlings to cope with drought stress. Gas-exchange, water potential, photosynthetic pigments, soluble sugars, free amino acids, glutathione and proteomic analyses were carried out on control and drought-stressed seedlings in greenhouse conditions. Gas-exchange determinations were also assessed in field-planted seedlings in order to validate the greenhouse experimental conditions. Drought-tolerant seed sources presented higher values of photosynthetic rates, water use efficiency, photosynthetic pigments and soluble carbohydrates concentrations. We observed the same pattern of variation of photosynthesis rate and maximal efficiency of PSII in field. Interestingly drought-tolerant seed sources exhibited increased levels of glutathione, methionine and cysteine. The proteomic profile of drought tolerant seedlings identified two heat shock proteins and an enzyme related to methionine biosynthesis that were not present in drought sensitive seedlings, pointing to the synthesis of sulfur amino acids as a limiting factor for drought tolerance in Pinus halepensis. Our results established physiological and molecular traits useful as distinctive markers to predict drought tolerance in Pinus halepensis provenances that could be reliably used in reforestation programs in drought prone areas. PMID:28791030

Drought Tolerance in Pinus halepensis Seed Sources As Identified by Distinctive Physiological and Molecular Markers.

PubMed

Taïbi, Khaled; Del Campo, Antonio D; Vilagrosa, Alberto; Bellés, José M; López-Gresa, María Pilar; Pla, Davinia; Calvete, Juan J; López-Nicolás, José M; Mulet, José M

2017-01-01

Drought is one of the main constraints determining forest species growth, survival and productivity, and therefore one of the main limitations for reforestation or afforestation. The aim of this study is to characterize the drought response at the physiological and molecular level of different Pinus halepensis (common name Aleppo pine) seed sources, previously characterized in field trials as drought-sensitive or drought-tolerant. This approach aims to identify different traits capable of predicting the ability of formerly uncharacterized seedlings to cope with drought stress. Gas-exchange, water potential, photosynthetic pigments, soluble sugars, free amino acids, glutathione and proteomic analyses were carried out on control and drought-stressed seedlings in greenhouse conditions. Gas-exchange determinations were also assessed in field-planted seedlings in order to validate the greenhouse experimental conditions. Drought-tolerant seed sources presented higher values of photosynthetic rates, water use efficiency, photosynthetic pigments and soluble carbohydrates concentrations. We observed the same pattern of variation of photosynthesis rate and maximal efficiency of PSII in field. Interestingly drought-tolerant seed sources exhibited increased levels of glutathione, methionine and cysteine. The proteomic profile of drought tolerant seedlings identified two heat shock proteins and an enzyme related to methionine biosynthesis that were not present in drought sensitive seedlings, pointing to the synthesis of sulfur amino acids as a limiting factor for drought tolerance in Pinus halepensis . Our results established physiological and molecular traits useful as distinctive markers to predict drought tolerance in Pinus halepensis provenances that could be reliably used in reforestation programs in drought prone areas.

The effectiveness of cut-proof glove liners: cut and puncture resistance, dexterity, and sensibility.

PubMed

Salkin, J A; Stuchin, S A; Kummer, F J; Reininger, R

1995-11-01

Five types of commercial glove liners (within double latex gloves) were compared to single and double latex gloves for cut and puncture resistance and for relative manual dexterity and degree of sensibility. An apparatus was constructed to test glove-pseudofinger constructs in either a cutting or puncture mode. Cutting forces, cutting speed, and type of blade (serrated or scalpel blade) were varied and the time to cut-through measured by an electrical conductivity circuit. Penetration forces were similarly determined with a scalpel blade and a suture needle using a spring scale loading apparatus. Dexterity was measured with an object placement task among a group of orthopedic surgeons. Sensibility was assessed with Semmes-Weinstein monofilaments, two-point discrimination, and vibrametry using standard techniques and rating scales. A subjective evaluation was performed at the end of testing. Time to cut-through for the liners ranged from 2 to 30 seconds for a rapid oscillating scalpel and 4 to 40 seconds for a rapid oscillating serrated knife under minimal loads. When a 1 kg load was added, times to cut-through ranged from 0.4 to 1.0 second. In most cases, the liners were superior to double latex. On average, 100% more force was required to penetrate the liners with a scalpel and 50% more force was required to penetrate the liners with a suture needle compared to double latex. Object placement task times were not significantly liners compared to double latex gloves. Semmes-Weinstein monofilaments, two-point discrimination, and vibrametry showed no difference in sensibility among the various liners and double latex gloves. Subjects felt that the liners were minimally to moderately impairing. An acclimation period may be required for their effective use.

Regional ontogeny of New England salt marsh die-off.

PubMed

Coverdale, Tyler C; Bertness, Mark D; Altieri, Andrew H

2013-10-01

Coastal areas are among the world's most productive and highly affected ecosystems. Centuries of human activity on coastlines have led to overexploitation of marine predators, which in turn has led to cascading ecosystem-level effects. Human effects and approaches to mediating them, however, differ regionally due to gradients in biotic and abiotic factors. Salt marsh die-off on Cape Cod, Massachusetts (U.S.A.), triggered by a recreational-fishing-induced trophic cascade that has released herbivorous crabs from predator control, has been ongoing since 1976. Similar salt marsh die-offs have been reported in Long Island Sound and Narragansett Bay (U.S.A.), but the driving mechanism of these die-offs has not been examined. We used field experiments to assess trophic interactions and historical reconstructions of 24 New England marshes to test the hypotheses that recreational fishing and predator depletion are a regional trigger of salt marsh die-off in New England and that die-offs in Long Island Sound and Narragansett Bay are more recent than those on Cape Cod. Predator depletion was the general trigger of marsh die-off and explained differences in herbivorous crab abundance and the severity of die-off across regions. Die-offs in Long Island Sound and Narragansett Bay are following a trajectory similar to die-off on Cape Cod, but are approximately 20 years behind those on Cape Cod. As a result, die-off currently affects 31.2% (SE 2.2) of low-marsh areas in Long Island Sound and Narragansett Bay, less than half the severity of die-off on Cape Cod. Our results contribute to the growing evidence that recreational fishing is an increasing threat to coastal ecosystems and that studying the effects of human activity at regional scales can provide insight into local effects and aid in early detection and potential remediation. © 2013 Society for Conservation Biology.

Bilingual Skills Training Program. Meat Cutting. Module 3.0: Identifying and Cutting Meat and By-Products.

ERIC Educational Resources Information Center

Northern New Mexico Community Coll., El Rito.

This module on identifying and cutting of meat and by-products is the third of three (CE 028 291-293) in the meat cutting course of a bilingual skills training program. The course is designed to furnish theoretical and laboratory experience in the cutting of beef, pork, poultry, lamb, and mutton. Module objectives are for students to develop…

25 CFR 304.5 - Dies to identify tribe.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 25 Indians 2 2014-04-01 2014-04-01 false Dies to identify tribe. 304.5 Section 304.5 Indians INDIAN ARTS AND CRAFTS BOARD, DEPARTMENT OF THE INTERIOR NAVAJO, PUEBLO, AND HOPI SILVER, USE OF GOVERNMENT MARK § 304.5 Dies to identify tribe. Dies are marked with name of tribe. A Navajo stamp will be...

25 CFR 304.5 - Dies to identify tribe.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 25 Indians 2 2011-04-01 2011-04-01 false Dies to identify tribe. 304.5 Section 304.5 Indians INDIAN ARTS AND CRAFTS BOARD, DEPARTMENT OF THE INTERIOR NAVAJO, PUEBLO, AND HOPI SILVER, USE OF GOVERNMENT MARK § 304.5 Dies to identify tribe. Dies are marked with name of tribe. A Navajo stamp will be...

25 CFR 304.5 - Dies to identify tribe.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 25 Indians 2 2012-04-01 2012-04-01 false Dies to identify tribe. 304.5 Section 304.5 Indians INDIAN ARTS AND CRAFTS BOARD, DEPARTMENT OF THE INTERIOR NAVAJO, PUEBLO, AND HOPI SILVER, USE OF GOVERNMENT MARK § 304.5 Dies to identify tribe. Dies are marked with name of tribe. A Navajo stamp will be...

25 CFR 304.5 - Dies to identify tribe.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 25 Indians 2 2013-04-01 2013-04-01 false Dies to identify tribe. 304.5 Section 304.5 Indians INDIAN ARTS AND CRAFTS BOARD, DEPARTMENT OF THE INTERIOR NAVAJO, PUEBLO, AND HOPI SILVER, USE OF GOVERNMENT MARK § 304.5 Dies to identify tribe. Dies are marked with name of tribe. A Navajo stamp will be...

Exponential fertilization of Pinus monticola seedlings: nutrient uptake efficiency, leaching fractions, and early outplanting performance

Treesearch

R. Kasten Dumroese; Deborah S. Page-Dumroese; K. Francis Salifu; Douglass F. Jacobs

2005-01-01

We evaluated nutrient uptake efficiency and subsequent leaching fractions for western white pine (Pinus monticola Dougl. ex D. Don) seedlings grown with exponentially increasing or conventional (constant) fertilization in a greenhouse. Conventional fertilization was associated with higher leachate electrical conductivity and greater nutrient losses,...

Physiology of fresh-cut fruits and vegetables

USDA-ARS?s Scientific Manuscript database

The idea to pre-process fruits and vegetables in the fresh state started with fresh-cut salads and now has expanded to fresh-cut fruits and other vegetables. The fresh-cut portion of the fresh produce industry includes fruits, vegetables, sprouts, mushrooms and even herbs that are cut, cored, sliced...

21 CFR 882.4275 - Dowel cutting instrument.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Dowel cutting instrument. 882.4275 Section 882...) MEDICAL DEVICES NEUROLOGICAL DEVICES Neurological Surgical Devices § 882.4275 Dowel cutting instrument. (a) Identification. A dowel cutting instrument is a device used to cut dowels of bone for bone grafting. (b...

When Students Cut Themselves

ERIC Educational Resources Information Center

Malikow, Max

2006-01-01

Masochism, the irrational self-infliction of pain, is more easily defined than understood. Once, a teacher used the word "cutting" only reference to a student skipping class. But, in recent years, it has taken on additional meaning. Cutting, or self-injury, is a deliberate self-harming behavior but without conscious suicidal ideation. To define…

Assisted dying - should the UK change its stance?

PubMed

Gordon, Daniel; Raphael, Claire E; Vassiliou, Vassilios

2015-04-01

Along with an increasing interest in assisted dying by many European and North American countries, some of which have already modified their existing laws to accommodate this, the interest in assisted dying in the UK has increased once again following Lord Falconer's Assisted Dying for the Terminally Ill Bill. Drawing on examples from countries where similar assisted dying laws are already in place, this article analyses and contextualises the proposed bill and discusses its potential pitfalls and benefits for the UK. © The European Society of Cardiology 2015 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

Meditations on the unitary rhythm of dying-grieving.

PubMed

Malinski, Violet M

2012-07-01

When someone faces loss of a loved one, that person simultaneously grieves and dies a little, just as the one dying also grieves. The author's personal conceptualization of dying and grieving as a unitary rhythm is explored based primarily on her interpretation of Rogers' science of unitary human beings, along with selected examples from related nursing literature and from the emerging focus on continuing bonds in other disciplines. Examples from contemporary songwriters that depict such a unitary conceptualization are given along with personal examples. The author concludes with her description of the unitary rhythm of dying-grieving.

Clinal differentiation and putative hybridization in a contact zone of Pinus ponderosa and P. arizonica (Pinaceae).

PubMed

Epperson, B K; Telewski, F W; Plovanich-Jones, A E; Grimes, J E

2001-06-01

The widely distributed Pinus subsection Ponderosae is a species complex that has a transition zone among taxa in the southwestern United States. In southern Arizona and New Mexico at least two recognized taxa, Pinus ponderosa var. scopulorum and Pinus arizonica or P. ponderosa var. arizonica, are known to coexist in close proximity. In this study, we report the existence of populations where the taxa are sympatric. One of the key characteristics distinguishing taxa is the number of needles per fascicle; P. ponderosa typically has three, P. arizonica has five. We examined the spatial distribution of needle-number types in a belt transect that covers a transition zone from nearly pure three-needle types at the top of Mount Lemmon to five-needle types downslope, in the Santa Catalina Mountains, Arizona. The spatial distribution is inconsistent with there being both free interbreeding among types and selective neutrality of types. Trees with intermediate types, having combinations of three, four, and five needles and/or mean numbers of needles between 3.0 and 5.0, are spatially concentrated in the middle of the transition zone. The spatial distribution supports the occurrence of hybridization and introgression, and this is consistent with reported crossabilities of the types. The results suggest that selection is acting, either on needle number per se or on other traits of the ecotype with which it may be in linkage disequilibrium, to maintain the observed steep clinal differentiation.

Will the UK Supreme Court allow assisted dying?

PubMed

Griffith, Richard

MPs overwhelmingly voted against passing the Assisted Dying Bill into law in September 2015. The Bill was defeated by a majority of 212, despite the heartfelt pleas of many MPs to pass it into law. The size of the defeat means that it is unlikely that Parliament will consider a similar law for many years. Yet many considered the Bill their last opportunity to make assisted dying lawful. There is, however, one further possible way assisted dying could become lawful in the UK--and that would be where the Supreme Court allowed it. In this article, the author reviews the Supreme Court's decision in R (on the application of Nicklinson v Ministry of Justice [2014] and considers how likely it is that the Supreme Court will now sanction assisted dying following Parliament's refusal to enact an assisted dying law.

49 CFR 234.269 - Cut-out circuits.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 4 2011-10-01 2011-10-01 false Cut-out circuits. 234.269 Section 234.269..., Inspection, and Testing Inspections and Tests § 234.269 Cut-out circuits. Each cut-out circuit shall be... of this section, a cut-out circuit is any circuit which overrides the operation of automatic warning...

49 CFR 234.269 - Cut-out circuits.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Cut-out circuits. 234.269 Section 234.269..., Inspection, and Testing Inspections and Tests § 234.269 Cut-out circuits. Each cut-out circuit shall be... of this section, a cut-out circuit is any circuit which overrides the operation of automatic warning...

The influence of cutting speed and cutting initiation location in specimen preparation for the microtensile bond strength test.

PubMed

Abreu, Celina Wanderley; Santosb, Jarbas F; Passos, Sheila Pestana; Michida, Silvia Masae; Takahashi, Fernando Eidi; Bottino, Marco Antonio

2011-06-01

This study evaluated the effect of cutting initiation location and cutting speed on the bond strength between resin cement and feldspathic ceramic. Thirty-six blocks (6.4 x 6.4 x 4.8 mm) of ceramic (Vita VM7) were produced. The ceramic surfaces were etched with 10% hydrofluoric acid gel for 60 s and then silanized. Each ceramic block was placed in a silicon mold with the treated surface exposed. A resin cement (Variolink II) was injected into the mold over the treated surface and polymerized. The resin cement-ceramic blocks were divided into two groups according to experimental conditions: a) cutting initiation location - resin cement, ceramic and interface; and b) cutting speed - 10,000, 15,000, and 20,000 rpm. The specimens were sectioned to achieve non-trimmed bar specimens. The microtensile test was performed in a universal testing machine (1 mm/min). The failure modes were examined using an optical light microscope and SEM. Bond strength results were analyzed using one-way ANOVA and Tukey's test (α = 0.05). Significant influences of cutting speed and initiation location on bond strength (p < 0.05) were observed. The highest mean was achieved for specimens cut at 15,000 rpm at the interface (15.12 ± 5.36 MPa). The lowest means were obtained for specimens cut at the highest cutting speed in resin cement (8.50 ± 3.27 MPa), and cut at the lowest cutting speed in ceramic (8.60 ± 2.65 MPa). All groups showed mainly mixed failure (75% to 100%). The cutting speed and initiation location are important factors that should be considered during specimen preparation for microtensile bond strength testing, as both may influence the bond strength results.

Effect of body condition on consumption of pine needles (Pinus ponderosa) by beef cows

USDA-ARS?s Scientific Manuscript database

We determined if cattle in low (LBC) or high body condition (HBC) would consume different amounts of green pine needles (Pinus ponderosa). Cattle (mature; open Hereford and Hereford x Angus) were fed an adequate basal diet (alfalfa pellets) for Trials 1 and 2; during Trials 3 and 4 cows were fed hig...

Anatomical and cellular responses of Pinus monticola stem tissues to invasion by Cronartium ribicola

Treesearch

J. W. Hudgins; G. I . McDonald; P. J. Zambino; N. B. Klopfenstein; V. R. Franceschi

2005-01-01

White pine blister rust (Cronartium ribicola) causes extensive damage to white pines and their associated ecosystems across North America. The anatomical and cellular characteristics of C. ribicola colonization in Pinus monticola branch and stem tissues were studied as a basis for understanding host tree reactions that may be related to resistance. Samples examined...

Southern Pine Beetle Survival In Trees Felled By the Cut and Top-Cut and Leave Method

Treesearch

J.D. Hodges; R.C. Thatcher

1976-01-01

When the cut & top-cut & leave method was used for control of the southern pine beetle in Central Louisiana, trees were felled into the open or into shade in September, June, July, December, and January. Survival was greatest in September, moderate in July, and relatively low in June, December, and January. The cut and top treatment resulted in lower beetle...

Simulation of Escherichia coli O157:H7 behavior in fresh-cut lettuce under dynamic temperature conditions during distribution from processing to retail.

PubMed

McKellar, Robin C; LeBlanc, Denyse I; Lu, Jianbo; Delaquis, Pascal

2012-03-01

The temperature of packaged lettuce was recorded throughout a retail supply chain in Canada during the various stages of storage and shipping from the processor to retail. Temperatures were monitored in 27 cases of lettuce destined for three stores in three replicate trials conducted during the winter. A dynamic model that predicts the effect of temperature on the growth or die-off of Escherichia coli O157:H7 in packaged fresh-cut lettuce was applied to simulate the behavior of E. coli O157:H7 in the system. Simulations were carried out using distributions to account for variation in the temperature parameter and the die-off coefficient of the dynamic growth/death model. The results indicate that there was a predicted overall mean decline in cell numbers of 0.983 log cfu g⁻¹ and that the extent of cell death was proportional to the total time spent in the cold chain. Slight growth was predicted in a few instances when the dynamic temperature was above the permissive temperature of 5°C. These results suggest that generally there would be little or no growth of E. coli O157:H7 in product maintained at the proper temperature in the chain. Moreover, the predicted decline in cell numbers at refrigeration temperatures suggests that storage at 5°C or below prior to consumption would reduce populations of the pathogen in fresh-cut lettuce.

27 CFR 6.92 - Newspaper cuts.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Newspaper cuts. 6.92 Section 6.92 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY LIQUORS âTIED-HOUSEâ Exceptions § 6.92 Newspaper cuts. Newspaper cuts, mats, or...

49 CFR 236.52 - Relayed cut-section.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 4 2011-10-01 2011-10-01 false Relayed cut-section. 236.52 Section 236.52...: All Systems Track Circuits § 236.52 Relayed cut-section. Where relayed cut-section is used in... shall be open and the track circuit shunted when the track relay at such cut-section is in deenergized...

49 CFR 236.52 - Relayed cut-section.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Relayed cut-section. 236.52 Section 236.52...: All Systems Track Circuits § 236.52 Relayed cut-section. Where relayed cut-section is used in... shall be open and the track circuit shunted when the track relay at such cut-section is in deenergized...

Portable punch and die jig

DOEpatents

Lewandowski, Edward F.; Anderson, Petrus A.

1978-01-01

A portable punch and die jig includes a U-shaped jig of predetermined width having a slot of predetermined width in the base thereof extending completely across the width of the jig adapted to fit over the walls of rectangular tubes and a punch and die assembly disposed in a hole extending through the base of the jig communicating with the slot in the base of the jig for punching a hole in the walls of the rectangular tubes at precisely determined locations.

Thinning and underburning effects on ground fuels in Jeffrey pine

Treesearch

R.F. Walker; R.M. Fecko; W.B. Frederick; J.D. Murphy; D.W. Johnson; W.W. Miller

2007-01-01

Thinning with cut-to-length and whole-tree harvesting systems followed by underburning were evaluated for their impacts on downed and dead fuel loading by timelag category in eastern Sierra Nevada Jeffrey pine (Pinus jeffreyi Grev. & Balf.). Cut-to-length harvesting resulted in an approximate doubling of total fuel loading to 113829 kg ha

30 CFR 717.14 - Backfilling and grading of road cuts, mine entry area cuts, and other surface work areas.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 3 2011-07-01 2011-07-01 false Backfilling and grading of road cuts, mine entry area cuts, and other surface work areas. 717.14 Section 717.14 Mineral Resources OFFICE OF SURFACE... MINING GENERAL PERFORMANCE STANDARDS § 717.14 Backfilling and grading of road cuts, mine entry area cuts...

49 CFR 213.352 - Torch cut rail.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 4 2011-10-01 2011-10-01 false Torch cut rail. 213.352 Section 213.352... Torch cut rail. (a) Except as a temporary repair in emergency situations no rail having a torch cut end shall be used. When a rail end with a torch cut is used in emergency situations, train speed over that...

49 CFR 213.352 - Torch cut rail.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Torch cut rail. 213.352 Section 213.352... Torch cut rail. (a) Except as a temporary repair in emergency situations no rail having a torch cut end shall be used. When a rail end with a torch cut is used in emergency situations, train speed over that...

Improvement of Die Corner Filling in Box-shape Stepped Tubes Hydroforming

NASA Astrophysics Data System (ADS)

Hosseini-Farrash, S. H.; Elyasi, M.; Bakhshi-Jooybari, M.; Gorji, A.

2011-01-01

A new die design to improve the die corner filling in the hydroforming of square-sectional stepped tubes is presented. The proposed die-set contains two additional bushes, compared to the common tube hydroforming dies. First, the tube is placed into the die, filled with liquid, and sealed with the punches. Then, by increasing the internal pressure, the tube is bulged and contacts the die walls (bulging stage). By maintaining the internal pressure, the two upper and lower bushes move until the die cavity is filled completely (calibration stage). The proposed die was simulated and the results show that sharp corners of the part and relatively complete filling of the die cavity can be obtained by using this die set. In order to verify the results, some experiments have been carried out. The experimental results verified the results obtained from the simulations. The thickness distribution of the part is also investigated and it is shown that fairly uniform thickness distribution can be obtained by using the proposed die set.

LEAF AREA INDEX (LAI) CHANGE DETECTION ANALYSIS ON LOBLOLLY PINE (PINUS TAEDA) FOLLOWING COMPLETE UNDERSTORY REMOVAL

EPA Science Inventory

The confounding effect of understory vegetation contributions to satellite-derived estimates of leaf area index (LAI) was investigated on two loblolly pine (Pinus taeda) forest stands located in Virginia and North Carolina. In order to separate NDVI contributions of the dominantc...

Budget cuts.

PubMed

1996-05-31

The House of Representatives approved a Federal budget for fiscal 1997. The budget calls for cutting $1.5 billion from the current $23 billion budget for the Department of Health and Human Services (DHHS). Only half of the DHHS money goes to the National Institutes of Health, whose research programs were expected to remain intact. DHHS programs, such as the Ryan White CARE Act and prevention programs run by the Centers for Disease Control and Prevention (CDC) are likely to bear the brunt of the cuts. The House Veterans Affairs/Housing and Urban Development appropriations bill will be reviewed during the week of June 3, 1996. The Senate envisions a $1.5 billion reduction in DHHS programs, although the action is not final.

Laser cutting of sodium silicate glasses

NASA Astrophysics Data System (ADS)

Buchanov, V. V.; Kazarian, M. A.; Kustov, M. E.; Mashir, Yu. I.; Murav'ev, E. N.; Revenko, V. I.; Solinov, E. F.

2018-04-01

The problems of through laser cutting of sodium silicate glasses by laser-controlled thermal cleavage are considered. A wide variety of obtained end face shapes is demonstrated. It is shown that the strength of glass samples cut by the laser is about two times higher than that of samples cut by a glass cutter.

Robot based deposition of WC-Co HVOF coatings on HSS cutting tools as a substitution for solid cemented carbide cutting tools

NASA Astrophysics Data System (ADS)

Tillmann, W.; Schaak, C.; Biermann, D.; Aßmuth, R.; Goeke, S.

2017-03-01

Cemented carbide (hard metal) cutting tools are the first choice to machine hard materials or to conduct high performance cutting processes. Main advantages of cemented carbide cutting tools are their high wear resistance (hardness) and good high temperature strength. In contrast, cemented carbide cutting tools are characterized by a low toughness and generate higher production costs, especially due to limited resources. Usually, cemented carbide cutting tools are produced by means of powder metallurgical processes. Compared to conventional manufacturing routes, these processes are more expensive and only a limited number of geometries can be realized. Furthermore, post-processing and preparing the cutting edges in order to achieve high performance tools is often required. In the present paper, an alternative method to substitute solid cemented carbide cutting tools is presented. Cutting tools made of conventional high speed steels (HSS) were coated with thick WC-Co (88/12) layers by means of thermal spraying (HVOF). The challenge is to obtain a dense, homogenous, and near-net-shape coating on the flanks and the cutting edge. For this purpose, different coating strategies were realized using an industrial robot. The coating properties were subsequently investigated. After this initial step, the surfaces of the cutting tools were ground and selected cutting edges were prepared by means of wet abrasive jet machining to achieve a smooth and round micro shape. Machining tests were conducted with these coated, ground and prepared cutting tools. The occurring wear phenomena were analyzed and compared to conventional HSS cutting tools. Overall, the results of the experiments proved that the coating withstands mechanical stresses during machining. In the conducted experiments, the coated cutting tools showed less wear than conventional HSS cutting tools. With respect to the initial wear resistance, additional benefits can be obtained by preparing the cutting edge by means

Vector Analysis Identify Loblolly Pine (Pinus taeda L.) Phosphorus Deficiency on a Beauregard Soil

Treesearch

A. Bekele; W.H. Hundall; A.E. Tiarks

1999-01-01

We studied the response of densely stocked one-year-old loblolly pine (Pinus taeda L.) to N and P fertilizers on a Beauregard silt loam (fine silty, siliceous, thermic, Plinthaquic Paleudults). A continuous function" experimental design with three replications was used. Each replication consisted of 12 m X 12 m plots, with three trees planted...

Accelerated Growth and Initial Flowering of S2 Pinus Banksiana Selected for Precocious Flowering

Treesearch

Hyun Kang; Robert A. Cecich

1999-01-01

An accelerated growth protocol was applied in a greenhouse to hasten flowering in 13 S2 lines of jack pine (Pinus banksiana Lamb.) selected for precocious flowering. Seeds were sown on October 1. After the artificial "summer, fall, winter, and spring," seedlings were placed outdoors between June 20 and November 1. Ovulate strobili were...

Are the same tapes really the same? Ultrasound study of laser-cut and mechanically cut TVT-O post-operative behavior.

PubMed

Rusavy, Zdenek; Masata, Jaromir; Svabik, Kamil; Hubka, Petr; Zvara, Karel; Martan, Alois

2017-11-25

TVT-O production has been modified to laser cutting from mechanical cutting. We compared the behavior of laser and mechanically cut tension-free vaginal tape-obturator (TVT-O) using ultrasound at various time points after surgery. This is a retrospective analysis of clinical and ultrasound data from two previously reported randomized controlled trials with TVT-O. Behavior of mechanically cut TVT-O implanted in January 2007 to November 2009 and laser-cut TVT-O implanted in May 2010 to May 2012 was assessed by ultrasound at day 1, the 2nd week, the 3rd month, and the 1st and 2nd years post-operatively. Bladder neck and tape margins positions were described by coordinates in the orthogonal system calculated from polar coordinates. Tape mobility was measured as a change in the upper and lower tape margin position from rest to maximal Valsalva. Comparison of 2-year subjective and objective surgery outcomes was also performed. In total, 68 mechanically cut and 50 laser-cut TVT-Os were implanted. Follow-up data were available from 49 and 45 women respectively. No differences in any baseline characteristics or bladder neck mobility were observed. Significantly lower tape mobility was observed on day 1 and week 2 after mechanically cut TVT-O, although subsequent mobility was comparable to laser-cut TVT-O. The subjective and objective surgery outcomes were comparable. Although without clinical significance, early postoperative behavior of the mechanically cut and laser-cut TVT-O tapes differs. The less stiff, mechanically-cut TVT-O loosens within 2 weeks of implantation, whereas the stiffer, laser-cut TVT-O keeps its tension.

Chemical composition and antimicrobial activity of essential oil from cones of Pinus koraiensis.

PubMed

Lee, Jeong-Ho; Yang, Hye-Young; Lee, Hong-Sub; Hong, Soon-Kwang

2008-03-01

The essential oil from the cones of Pinus koraiensis was prepared after removing the seeds, and its chemical composition analyzed using gas chromatography-mass spectrometry (GC-MS). Hydrodistillation of the P. koraiensis cones yielded 1.07% (v/w) of essential oil, which was almost three times the amount of essential oil extracted from the needles of the same plant. Moreover, the antimicrobial activities of the oil against the growth of Gram-positive bacteria, Gram-negative bacteria, and fungi were evaluated using the agar disc diffusion method and broth microdilution method. Eighty-seven components, comprising about 96.8% of the total oil, were identified. The most abundant oil components were limonene (27.90%), alpha-pinene (23.89%), beta-pinene (12.02%), 3-carene (4.95%), beta-myrcene (4.53%), isolongifolene (3.35%), (-)-bornyl acetate (2.02%), caryophyllene (1.71%), and camphene (1.54%). The essential oil was confirmed to have significant antimicrobial activities, especially against pathogenic fungal strains such as Candida glabrata YFCC 062 and Cryptococcus neoformans B 42419. Therefore, the present results indicate that the essential oil from the cones of Pinus koraiensis can be used in various ways as a nontoxic and environmentally friendly disinfectant.

Optimization of Composition and Heat Treating of Die Steels for Extended Lifetime

DOE Office of Scientific and Technical Information (OSTI.GOV)

David Schwam; John F. Wallace; Quanyou Zhou

2002-01-30

An ''average'' die casting die costs fifty thousand dollars. A die used in making die cast aluminum engine blocks can cost well over one million dollars. These costs provide a strong incentive for extension of die life. While vacuum quenched Premium Grade H13 dies have become the most widely used in the United States, tool makers and die casters are constantly searching for new steels and heat treating procedures to extend die life. This project was undertaken to investigate the effects of composition and heat treating on die life and optimize these parameters.

Teaching Budget Cuts to Third Graders

ERIC Educational Resources Information Center

Weiss, Dale

2011-01-01

As a teacher in the Milwaukee Public Schools (MPS) for the past 16 years, this author has grown used to dismal budget cut news arriving each February. Although cuts are always frustrating and their results burdensome, his school has been able to "hang on" reasonably well. This year, however, the budget cuts were extreme. The school's…

27 CFR 6.92 - Newspaper cuts.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2011-04-01 2011-04-01 false Newspaper cuts. 6.92 Section 6.92 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY LIQUORS âTIED-HOUSEâ Exceptions § 6.92 Newspaper cuts. Newspaper cuts, mats, or engraved blocks for use in retailers' advertisements...

Cutting tool form compensation system and method

DOEpatents

Barkman, W.E.; Babelay, E.F. Jr.; Klages, E.J.

1993-10-19

A compensation system for a computer-controlled machining apparatus having a controller and including a cutting tool and a workpiece holder which are movable relative to one another along a preprogrammed path during a machining operation utilizes a camera and a vision computer for gathering information at a preselected stage of a machining operation relating to the actual shape and size of the cutting edge of the cutting tool and for altering the preprogrammed path in accordance with detected variations between the actual size and shape of the cutting edge and an assumed size and shape of the cutting edge. The camera obtains an image of the cutting tool against a background so that the cutting tool and background possess contrasting light intensities, and the vision computer utilizes the contrasting light intensities of the image to locate points therein which correspond to points along the actual cutting edge. Following a series of computations involving the determining of a tool center from the points identified along the tool edge, the results of the computations are fed to the controller where the preprogrammed path is altered as aforedescribed. 9 figures.

Cutting tool form compensaton system and method

DOEpatents

Barkman, William E.; Babelay, Jr., Edwin F.; Klages, Edward J.

1993-01-01

A compensation system for a computer-controlled machining apparatus having a controller and including a cutting tool and a workpiece holder which are movable relative to one another along a preprogrammed path during a machining operation utilizes a camera and a vision computer for gathering information at a preselected stage of a machining operation relating to the actual shape and size of the cutting edge of the cutting tool and for altering the preprogrammed path in accordance with detected variations between the actual size and shape of the cutting edge and an assumed size and shape of the cutting edge. The camera obtains an image of the cutting tool against a background so that the cutting tool and background possess contrasting light intensities, and the vision computer utilizes the contrasting light intensities of the image to locate points therein which correspond to points along the actual cutting edge. Following a series of computations involving the determining of a tool center from the points identified along the tool edge, the results of the computations are fed to the controller where the preprogrammed path is altered as aforedescribed.

Microwave-assisted extraction and ultrasonic extraction to determine polycyclic aromatic hydrocarbons in needles and bark of Pinus pinaster Ait. and Pinus pinea L. by GC-MS.

PubMed

Ratola, Nuno; Lacorte, Sílvia; Barceló, Damià; Alves, Arminda

2009-01-15

Two different extraction strategies (microwave-assisted extraction (MAE) and ultrasonic extraction (USE)) were tested in the extraction of the 16 US Environmental Protection Agency (EPA) polycyclic aromatic hydrocarbons (PAHs) from pine trees. Extraction of needles and bark from two pine species common in the Iberian Peninsula (Pinus pinaster Ait. and Pinus pinea L.) was optimized using two amounts of sample (1g and 5 g) and two PAHs spiking levels (20 ng/g and 100 ng/g). In all cases, the clean-up procedure following extraction consisted in solid-phase extraction (SPE) with alumina cartridges. Quantification was done by gas chromatography (GC) with mass spectrometry (MS), using five deuterated PAH surrogate standards as internal standards. Limits of detection were globally below 0.2 ng/g. The method was robust for the matrices studied regardless of the extraction procedures. Recovery values between 70 and 130% were reached in most cases, except for high molecular weight PAHs (indeno[1,2,3-cd]pyrene, dibenzo[a,h]anthracene and benzo[ghi]perylene). A field study with naturally contaminated samples from eight sites (four in Portugal and four in Catalonia, Spain) showed that needles are more suitable biomonitors for PAHs, yielding concentrations from 2 to 17 times higher than those found in bark. The levels varied according to the sampling site, with the sum of the individual PAH concentrations between 213 and 1773 ng/g (dry weight). Phenanthrene was the most abundant PAH, followed by fluoranthene, naphthalene and pyrene.

Fungal endophytes in woody roots of Douglas-fir (Pseudotsuga menziesii) and ponderosa pine (Pinus ponderosa)

Treesearch

J. A. Hoff; Ned B. Klopfenstein; Geral I. McDonald; Jonalea R. Tonn; Mee-Sook Kim; Paul J. Zambino; Paul F. Hessburg; J. D. Rodgers; T. L. Peever; L. M. Carris

2004-01-01

The fungal community inhabiting large woody roots of healthy conifers has not been well documented. To provide more information about such communities, a survey was conducted using increment cores from the woody roots of symptomless Douglas-fir (Pseudotsuga menziesii) and ponderosa pine (Pinus ponderosa) growing in dry forests...

Ostryopsis davidiana seedlings inoculated with ectomycorrhizal fungi facilitate formation of mycorrhizae on Pinus tabulaeformis seedlings

Treesearch

Shu-Lan Bai; Guo-Lei Li; Yong Liu; R. Kasten Dumroese; Rui-Heng Lv

2009-01-01

Reforestation in China is important for reversing anthropogenic activities that degrade the environment. Pinus tabulaeformis is desired for these activities, but survival and growth of seedlings can be hampered by lack of ectomycorrhizae. When outplanted in association with Ostryopsis davidiana plants on reforestation sites, P. tabulaeformis seedlings become...

The effects of seed source health on whitebark pine (Pinus albicaulis) regeneration density after wildfire

Treesearch

Signe B. Leirfallom; Robert E. Keane; Diana F. Tomback; Solomon Z. Dobrowski

2015-01-01

Whitebark pine (Pinus albicaulis Engelm.) populations are declining nearly rangewide from a combination of factors, including mountain pine beetle (Dendroctonus ponderosae Hopkins, 1902) outbreaks, the exotic pathogen Cronartium ribicola J.C. Fisch. 1872, which causes the disease white pine blister rust, and successional replacement due to historical fire...

Dying in the age of choice.

PubMed

Black, Kathy; Csikai, Ellen L

2015-01-01

Due to the unprecedented increase in the United States aging demographics, many more people are living longer and reaching older ages than ever before. However, a longer life is not necessarily a better life, as the vast majority will face a period of prolonged deteriorating health prior to death. Although notable efforts have been underway that are designed to improve the end-of-life experience, increasing numbers of individuals express a desire and/or act upon an intent to end their lives precipitously. Though still limited, the options to actively participate in their own deaths are growing. Requests for a hastened death can occur among people of all ages and includes those with advanced illness as well as others wanting to die due to unbearable suffering. This article provides an overview of the ongoing discourse about the experience of dying faced by many older adults, including aspects frequently associated with "a good death." The limitations of established practices which seek to provide a "better" dying experience are identified followed by discussion of the growing availability of alternative options. Reflective considerations are presented to guide practice vis-à-vis the changing landscape surrounding options in dying.

Cutting Head for Ultrasonic Lithotripsy

NASA Technical Reports Server (NTRS)

Angulo, E. D.; Goodfriend, R.

1987-01-01

Kidney stones lodged in urinary tract disintegrated with increased safety and efficiency by cutting head attached to end of vibrated wire probe. Aligns probe with stone and enables probe to vibrate long enough to disintegrate stone. Design of cutting head reduces risk of metal-fatigue-induced breakage of probe tip leaving metal fragments in urinary tract. Teeth of cutting head both seat and fragment kidney stone, while extension of collar into catheter lessens mechanical strain in probe wire, increasing probe life and lessening danger of in situ probe breakage.

Experimental Investigations to evaluate the effects of cutting parameters on cutting temperature and residual stresses during milling process of the AISI 1045

NASA Astrophysics Data System (ADS)

Abdelkrim, M.; Brabie, G.; Belloufi, A.; Catalin, T.; Chirita, B.

2017-08-01

Today major metal cutting companies in industrial countries, looking to gain time and reduce manufacturing costs while respecting the environment. There are many phenomena which affect the quality and production costs of the product, including cutting efforts, cutting temperature, residual stresses, etc. A better understanding of these phenomena will reduce production costs and maximize productivity. The aim of this work is to analyze the effect of machining conditions (cutting speed, feed speed and cutting depth) on cutting temperature and residual stresses, during the milling operations using the response surface method. A good accuracy between predicted and measured values of the cutting temperature was found, the cutting speed and the depth of cut are parameters whose effect is most sensitive to the residual stresses and the cutting temperature.However, little influence has been registered in the case of an increase of the feed rate. The percentage of error is 4.57%, indicating that the numerical approach can accurately predict the cutting temperature of the AISI 1045.

Influence of Procerum Root Disease on the Water Relations of Eastern White Pine (Pinus strobus L.)

Treesearch

J.R. Butnor; J.R. Seiler; J.A. Gray

2000-01-01

Procerum root disease (PRD) is caused by the deuteromycete fungus Leptogruphium procerum (Kendr.) Wingf, formerly Verticic ladiella procera (Kendr.) and is most commonly isolated from Pinus sp. L., though the fungus has been isolated from other conifer species including Fraser fir (Abies fraseri...

Restoring table mountain pine (Pinus pungens Lamb.) communities with prescribed fire: an overview of current research

Treesearch

Nicole Turrill Welch; Thomas A. Waldrop

2001-01-01

Table mountain pine (Pinus pungens Lamb.) communities of the Southern Appalachian Mountains have been maintained historically by lightning- and human-caused fires. Characteristic stands have a table mountain pine overstory, a chestnut oak (Quercus prinus L.), scarlet oak (Q. coccinea Muenchh.), and blackgum (

Growth of five families of Pinus taeda L. during three years of ozone exposure

Treesearch

M.B. Adams; J.M. Kelly; G.E. Taylor; N.T. Edwards

1990-01-01

Loblolly pine (Pinus taeda L.) seedlings of five half-sib families were grown for 3 yr in the field in open-top chambers. The seedlings were fumigated during the growing seasons (approximately April-October) with ozone at the following target levels: subambient (CF), ambient (AMB), and ambient+ 60 ppb (AMB+). At the end of the three growing seasons...

Carry-Over Effects of Water and Nutrient Supply on Water Use of Pinus Taeda

Treesearch

Brent E. Ewers; Ram Oren; Timothy J. Albaugh; Phillip M. Dougherty

1999-01-01

Abstract. A study of the effects of nutrients and water supply (2 X 2 factorial experiment) was conducted in a 12-yr-old stand of loblolly pine (Pinus taeda L.) during a period in which soil moisture was not augmented by irrigation because of frequent rain events. Information on the responses of sapwood-to-leaf area ratio and...

Inheritance of the bark reaction resistance mechanism in Pinus monticola infected by Cronartium ribicola

Treesearch

Ray J. Hoff

1986-01-01

Necrotic reactions in branch or main stems of western white pine (Pinus monticola Dougl.) caused by infection by the blister rust fungus (Cronartium ribicola J. C. Fisch. ex Rabenh.) are a major mechanism of resistance. Overall, 26 percent of the seedlings eliminated the fungus via this defense system. Heritability based upon crossing family groups averaged 33 percent...

The genetics of shortleaf pine (Pinus echinata mill.) with implications for restoration and management

Treesearch

John F. Stewart; Rodney E. Will; Barbara S. Crane; C. Dana Nelson

2016-01-01

Shortleaf pine (Pinus echinata Mill.) is an important commercial timber resource and forest ecosystem component in the southeastern USA. The species occurs in mainly drier sites as an early- to mid-successional species, is fireadapted, and it plays an important role in the fire ecology of the region. However, shortleaf pine genetics are not well-studied, especially in...

Raise cutting diameters for increased returns

Treesearch

H. Clay Smith; G. R., Jr. Trimble; Paul S. DeBald

1979-01-01

Diameter-limit cutting is widely used to harvest logs in eastern hardwoods. Studies show that cutting limits are often set so low that they sacrifice financial returns. The value of lumber cut from logs is largely dependent on the diameter, grade, and tree species. As tree size increases so does the proportion of higher grade lumber, and this is reflected in improved...

Cutting Tool For Shaving Weld Beads

NASA Technical Reports Server (NTRS)

Hoffman, David S.; Mcferrin, David C.; Daniel, Ronald L., Jr.; Coby, John B., Jr.; Dawson, Sidney G.

1995-01-01

Cutting tool proposed for use in shaving weld beads flush with adjacent surfaces of weldments. Modified version of commercial pneumatically driven rotary cutting tool, cutting wheel of which turns at speeds sufficient for machining nickel alloys, titanium, and stainless steels. Equipped with forward-mounted handle and rear-mounted skid plate to maximize control and reduce dependence on skill of technician.

Hardwood Regeneration After Seed Tree Cutting

Treesearch

Robert L. Johnson; R. M. Krinard

1976-01-01

Seed trees left at two sites did not appear to influence the establishment or development of reproduction . Seed trees were mainly sweetgum and red oaks. Most reproduction was from sprouting of the stumps and roots of cut trees or from advanced seedlings present in the understory at the time of cutting. Eighteen years after cutting, dominant trees of the reproduction...

The effects of cutting parameters on cutting forces and heat generation when drilling animal bone and biomechanical test materials.

PubMed

Cseke, Akos; Heinemann, Robert

2018-01-01

The research presented in this paper investigated the effects of spindle speed and feed rate on the resultant cutting forces (thrust force and torque) and temperatures while drilling SawBones ® biomechanical test materials and cadaveric cortical bone (bovine and porcine femur) specimens. It also investigated cortical bone anisotropy on the cutting forces, when drilling in axial and radial directions. The cutting forces are only affected by the feed rate, whereas the cutting temperature in contrast is affected by both spindle speed and feed rate. The temperature distribution indicates friction as the primary heat source, which is caused by the rubbing of the tool margins and the already cut chips over the borehole wall. Cutting forces were considerably higher when drilling animal cortical bone, in comparison to cortical test material. Drilling direction, and therewith anisotropy, appears to have a negligible effect on the cutting forces. The results suggest that this can be attributed to the osteons being cut at an angle rather than in purely axial or radial direction, as a result of a twist drill's point angle. Copyright © 2017 IPEM. Published by Elsevier Ltd. All rights reserved.

Interactive effects of juvenile defoliation, light conditions, and interspecific competition on growth and ectomycorrhizal colonization of Fagus sylvatica and Pinus sylvestris seedlings.

PubMed

Trocha, Lidia K; Weiser, Ewa; Robakowski, Piotr

2016-01-01

Seedlings of forest tree species are exposed to a number of abiotic (organ loss or damage, light shortage) and biotic (interspecific competition) stress factors, which may lead to an inhibition of growth and reproduction and, eventually, to plant death. Growth of the host and its mycorrhizal symbiont is often closely linked, and hence, host damage may negatively affect the symbiont. We designed a pot experiment to study the response of light-demanding Pinus sylvestris and shade-tolerant Fagus sylvatica seedlings to a set of abiotic and biotic stresses and subsequent effects on ectomycorrhizal (ECM) root tip colonization, seedling biomass, and leaf nitrogen content. The light regime had a more pronounced effect on ECM colonization than did juvenile damage. The interspecific competition resulted in higher ECM root tip abundance for Pinus, but this effect was insignificant in Fagus. Low light and interspecific competition resulted in lower seedling biomass compared to high light, and the effect of the latter was partially masked by high light. Leaf nitrogen responded differently in Fagus and Pinus when they grew in interspecific competition. Our results indicated that for both light-demanding (Pinus) and shade-tolerant (Fagus) species, the light environment was a major factor affecting seedling growth and ECM root tip abundance. The light conditions favorable for the growth of seedlings may to some extent compensate for the harmful effects of juvenile organ loss or damage and interspecific competition.

Gas chromatography-mass spectrometry study of sterols from Pinus elliotti tissues.

NASA Technical Reports Server (NTRS)

Laseter, J. L.; Evans, R.; Weete, J. D.; Walkinshaw, C. H.

1973-01-01

A comparative study of the sterol components of slash pine (Pinus elliotti) callus tissue cultures, seeds, and seedlings was carried out using GC-MS techniques. Cholesterol, desmosterol, campesterol, stigmasterol, sitosterol and cycloeucalenol were identified in all tissues while lophenol and 24-methylenelophenol were identified in only the seed and seedlings. 24-Ethylidenelophenol was detected in trace concentrations in only the seedlings. Sitosterol was the predominant sterol component, i.e., 80.8, 38.1 and 47.8% of the tissue culture, seed and seedling sterols, respectively.

Darwin als Sehhilfe für die Psychologie - Evolutionspsychologie

NASA Astrophysics Data System (ADS)

Schwab, Frank

Im Folgenden geht es um Einäugige, stereoskopisches Sehen, weite und enge Horizonte, Monokel und Sonnenbrillen. Der Beitrag versucht die Metapher des Sehens und der Sehhilfen anzuwenden, um so zu verdeutlichen, welchen Gewinn die herkömmliche Psychologie durch die Verwendung einer Darwin'schen Brille erlangen kann.

Low Temperature Consolidation of Micro/Nanosilver Die-Attach Preforms

NASA Astrophysics Data System (ADS)

McCoppin, Jared; Reitz, Thomas L.; Miller, Ryan; Vijwani, Hema; Mukhopadhyay, Sharmila; Young, Daniel

2014-09-01

Organically passivated silver nanopowder paste-based sintering is considered a promising solution for die-attach in high temperature power and sensing electronic devices. However, oxygen requirements during burnout and inherently high shrinkage rates limit their use to small die sizes. This work reports an alternative fabrication method that resolves decomposition and shrinkage issues of the die-attach by utilizing a prestressed optimized tape cast mixture of micro- and nanosilver particles with a polypropylene carbonate binder. The effects of prestressing, micro/nanosilver bimodal distribution, and polymer content on resulting microstructure and shear strength were investigated. Prior to application as a die-attach, uniaxial compression of the tape was found to significantly decrease shrinkage and improve green strength. This pre-stressing strategy allows for a decoupling of the resulting die-attach materials properties from the pressure applied during assembly. Bimodal mixtures consisting of 1-3 μm spherical powders with nanosilver resulted in shear strengths comparable to those of pure nanosilver. Shear strength decreased as bimodal particle size increased above 5 μm. A polymer content of ˜10 wt.% polypropylene carbonate combined with prestressing was identified as optimal for maximizing die-attach shear strength while still maintaining pliability and formability. Tape casts that were prestressed to 212 MPa by uniaxially compression and formulated with 10 wt.% of polypropylene carbonate resulted in a die-attach material with a shear strength of 54 MPa when sintered. These materials were used to demonstrate void-free 25-mm2 die-attach assemblies, suggesting that tape cast micro/nanosilver materials may be a promising die-attach method for high temperature and large-area electronics devices.

Digitalisierung und Energie 4.0 - Wie schaffen wir die digitale Energiewende?

NASA Astrophysics Data System (ADS)

Irlbeck, Maximilian

Die digitale Energiewende verändert nachhaltig die Systeme der "alten" Energiewelt. Ein Zusammenwachsen verschiedener Domänen im Energiesystem, die durch digitale Technologie möglich wird, birgt enorme Herausforderungen, ist aber notwendig, um die Energiewende und ihre Ziele zu meistern. Dieser Beitrag beschreibt die Wirkung der Digitalisierung auf das Energiesystem, listet Charakteristika der digitalen Energiewende auf und schildert für verschiedene Domänen mögliche Zielvorstellungen, die durch digitale Technologie umsetzbar sind. Am Ende erläutert der Beitrag Handlungsschritte, die auf dem Weg zu einem erneuerbaren Energiesystem gegangen werden sollten und zeigt Probleme und Risiken einer Fehlentwicklung auf.

Complete chloroplast genome sequence and comparative analysis of loblolly pine (Pinus taeda L.) with related species

PubMed Central

Khan, Abdul Latif; Khan, Muhammad Aaqil; Shahzad, Raheem; Lubna; Kang, Sang Mo; Al-Harrasi, Ahmed; Al-Rawahi, Ahmed; Lee, In-Jung

2018-01-01

Pinaceae, the largest family of conifers, has a diversified organization of chloroplast (cp) genomes with two typical highly reduced inverted repeats (IRs). In the current study, we determined the complete sequence of the cp genome of an economically and ecologically important conifer tree, the loblolly pine (Pinus taeda L.), using Illumina paired-end sequencing and compared the sequence with those of other pine species. The results revealed a genome size of 121,531 base pairs (bp) containing a pair of 830-bp IR regions, distinguished by a small single copy (42,258 bp) and large single copy (77,614 bp) region. The chloroplast genome of P. taeda encodes 120 genes, comprising 81 protein-coding genes, four ribosomal RNA genes, and 35 tRNA genes, with 151 randomly distributed microsatellites. Approximately 6 palindromic, 34 forward, and 22 tandem repeats were found in the P. taeda cp genome. Whole cp genome comparison with those of other Pinus species exhibited an overall high degree of sequence similarity, with some divergence in intergenic spacers. Higher and lower numbers of indels and single-nucleotide polymorphism substitutions were observed relative to P. contorta and P. monophylla, respectively. Phylogenomic analyses based on the complete genome sequence revealed that 60 shared genes generated trees with the same topologies, and P. taeda was closely related to P. contorta in the subgenus Pinus. Thus, the complete P. taeda genome provided valuable resources for population and evolutionary studies of gymnosperms and can be used to identify related species. PMID:29596414

Fine-scale genetic structure of whitebark pine (Pinus albicaulis) associations with watershed and growth form

Treesearch

Deborah L. Rogers; Constance I. Millar; Robert D. Westfall

1999-01-01

The fine-scale genetic structure of a subalpine conifer, whitebark pine (Pinus albicaulis Engelm.), was studied at nested geographic levels from watershed to adjacent stems in the eastern Sierra Nevada Range of California. A combination of several characteristics contributed to unpredicted genetic structure in this species. This includes being one of...

Geographic patterns of genetic variation and population structure in Pinus aristata, Rocky Mountain bristlecone pine

Treesearch

Anna W. Schoettle; Betsy A. Goodrich; Valerie Hipkins; Christopher Richards; Julie Kray

2012-01-01

Pinus aristata Engelm., Rocky Mountain bristlecone pine, has a narrow core geographic and elevational distribution, occurs in disjunct populations, and is threatened by rapid climate change, white pine blister rust, and bark beetles. Knowledge of genetic diversity and population structure will help guide gene conservation strategies for this species. Sixteen sites...

The effect of mid-rotation fertilization on the wood properties of loblolly pine (Pinus taeda)

Treesearch

Finto Antony; Lewis Jordan; Laurence R. Schimleck; Richard F. Daniels; Alexander Clark III

2009-01-01

Mid-rotation fertilization is a common practice in the management of loblolly pine (Pinus taeda L.) plantations, typically providing large improvements in growth. However, concerns exist about the quality of wood produced following fertilization. The objective of this study was to develop an understanding of wood property changes following fertilization. Wood...

Trade-Offs between Growth Rate, Tree Size and Lifespan of Mountain Pine (Pinus montana) in the Swiss National Park

PubMed Central

Bigler, Christof

2016-01-01

A within-species trade-off between growth rates and lifespan has been observed across different taxa of trees, however, there is some uncertainty whether this trade-off also applies to shade-intolerant tree species. The main objective of this study was to investigate the relationships between radial growth, tree size and lifespan of shade-intolerant mountain pines. For 200 dead standing mountain pines (Pinus montana) located along gradients of aspect, slope steepness and elevation in the Swiss National Park, radial annual growth rates and lifespan were reconstructed. While early growth (i.e. mean tree-ring width over the first 50 years) correlated positively with diameter at the time of tree death, a negative correlation resulted with lifespan, i.e. rapidly growing mountain pines face a trade-off between reaching a large diameter at the cost of early tree death. Slowly growing mountain pines may reach a large diameter and a long lifespan, but risk to die young at a small size. Early growth was not correlated with temperature or precipitation over the growing period. Variability in lifespan was further contingent on aspect, slope steepness and elevation. The shade-intolerant mountain pines follow diverging growth trajectories that are imposed by extrinsic environmental influences. The resulting trade-offs between growth rate, tree size and lifespan advance our understanding of tree population dynamics, which may ultimately improve projections of forest dynamics under changing environmental conditions. PMID:26930294

Paraffin tissue microarrays constructed with a cutting board and cutting board arrayer.

PubMed

Vogel, Ulrich Felix

2010-05-01

Paraffin tissue microarrays (PTMAs) are blocks of paraffin containing up to 1300 paraffin tissue core biopsies (PTCBs). Normally, these PTCBs are punched from routine paraffin tissue blocks, which contain tissues of differing thicknesses. Therefore, the PTCBs are of different lengths. In consequence, the sections of the deeper portions of the PTMA do not contain all of the desired PTCBs. To overcome this drawback, cutting boards were constructed from panels of plastic with a thickness of 4 mm. Holes were drilled into the plastic and filled completely with at least one PTCB per hole. After being trimmed to a uniform length of 4 mm, these PTCBs were pushed from the cutting board into corresponding holes in a recipient block by means of a plate with steel pins. Up to 1000 sections per PTMA were cut without any significant loss of PTCBs, thereby increasing the efficacy of the PTMA technique.

Changing cultural attitudes towards female genital cutting.

PubMed

Vogt, Sonja; Mohmmed Zaid, Nadia Ahmed; El Fadil Ahmed, Hilal; Fehr, Ernst; Efferson, Charles

2016-10-27

As globalization brings people with incompatible attitudes into contact, cultural conflicts inevitably arise. Little is known about how to mitigate conflict and about how the conflicts that occur can shape the cultural evolution of the groups involved. Female genital cutting is a prominent example. Governments and international agencies have promoted the abandonment of cutting for decades, but the practice remains widespread with associated health risks for millions of girls and women. In their efforts to end cutting, international agents have often adopted the view that cutting is locally pervasive and entrenched. This implies the need to introduce values and expectations from outside the local culture. Members of the target society may view such interventions as unwelcome intrusions, and campaigns promoting abandonment have sometimes led to backlash as they struggle to reconcile cultural tolerance with the conviction that cutting violates universal human rights. Cutting, however, is not necessarily locally pervasive and entrenched. We designed experiments on cultural change that exploited the existence of conflicting attitudes within cutting societies. We produced four entertaining movies that served as experimental treatments in two experiments in Sudan, and we developed an implicit association test to unobtrusively measure attitudes about cutting. The movies depart from the view that cutting is locally pervasive by dramatizing members of an extended family as they confront each other with divergent views about whether the family should continue cutting. The movies significantly improved attitudes towards girls who remain uncut, with one in particular having a relatively persistent effect. These results show that using entertainment to dramatize locally discordant views can provide a basis for applied cultural evolution without accentuating intercultural divisions.

Identification of the critical depth-of-cut through a 2D image of the cutting region resulting from taper cutting of brittle materials

NASA Astrophysics Data System (ADS)

Gu, Wen; Zhu, Zhiwei; Zhu, Wu-Le; Lu, Leyao; To, Suet; Xiao, Gaobo

2018-05-01

An automatic identification method for obtaining the critical depth-of-cut (DoC) of brittle materials with nanometric accuracy and sub-nanometric uncertainty is proposed in this paper. With this method, a two-dimensional (2D) microscopic image of the taper cutting region is captured and further processed by image analysis to extract the margin of generated micro-cracks in the imaging plane. Meanwhile, an analytical model is formulated to describe the theoretical curve of the projected cutting points on the imaging plane with respect to a specified DoC during the whole cutting process. By adopting differential evolution algorithm-based minimization, the critical DoC can be identified by minimizing the deviation between the extracted margin and the theoretical curve. The proposed method is demonstrated through both numerical simulation and experimental analysis. Compared with conventional 2D- and 3D-microscopic-image-based methods, determination of the critical DoC in this study uses the envelope profile rather than the onset point of the generated cracks, providing a more objective approach with smaller uncertainty.

Craterlike structures on the laser cut surface

NASA Astrophysics Data System (ADS)

Shulyatyev, V. B.; Orishich, A. M.

2017-10-01

Analysis of the laser cut surface morphology remain topical. It is related with the fact that the surface roughness is the main index of the cut quality. The present paper deals with the experimental study of the relatively unstudied type of defects on the laser cut surface, dimples, or craters. According to the measurement results, amount of craters per unit of the laser cut surface area rises as the sheet thickness rises. The crater diameter rises together with the sheet thickness and distance from the upper sheet edge. The obtained data permit concluding that the defects like craters are observed predominantly in the case of thick sheets. The results agree with the hypothesis of crater formation as impact structures resulting from the melt drops getting on the cut channel walls upon separation from the cut front by the gas flow.

Cryogenic ribbon-cutting

NASA Image and Video Library

2011-03-30

NASA cut the ribbon on a new cryogenics control center at John C. Stennis Space Center on March 30. The new facility is part of a project to strengthen Stennis facilities to withstand the impacts of future storms like hurricane Katrina in 2005. Participants in the ribbon-cutting included (l to r): Jason Zuckerman, director of project management for The McDonnel Group; Keith Brock, director of the NASA Project Directorate at Stennis; Stennis Deputy Director Rick Gilbrech; Steve Jackson of Jacobs Technology; and Troy Frisbie, Cryo Control Center Construction project manager for NASA Center Operations at Stennis.

Soil moisture and its role in growth-climate relationships across an aridity gradient in semiarid Pinus halepensis forests.

PubMed

Manrique-Alba, Àngela; Ruiz-Yanetti, Samantha; Moutahir, Hassane; Novak, Klemen; De Luis, Martin; Bellot, Juan

2017-01-01

In Mediterranean areas with limited availability of water, an accurate knowledge of growth response to hydrological variables could contribute to improving management and stability of forest resources. The main goal of this study is to assess the temporal dynamic of soil moisture to better understand the water-growth relationship of Pinus halepensis forests in semiarid areas. The estimates of modelled soil moisture and measured tree growth were used at four sites dominated by afforested Pinus halepensis Mill. in south-eastern Spain with 300 to 609mm mean annual precipitation. Firstly, dendrochronological samples were extracted and the widths of annual tree rings were measured to compute basal area increments (BAI). Secondly, soil moisture was estimated over 20 hydrological years (1992-2012) by means of the HYDROBAL ecohydrological model. Finally, the tree growth was linked, to mean monthly and seasonal temperature, precipitation and soil moisture. Results depict the effect of soil moisture on growth (BAI) and explain 69-73% of the variance in semiarid forests, but only 51% in the subhumid forests. This highlights the fact that that soil moisture is a suitable and promising variable to explain growth variations of afforested Pinus halepensis in semiarid conditions and useful for guiding adaptation plans to respond pro-actively to water-related global challenges. Copyright © 2016 Elsevier B.V. All rights reserved.

Improvement Cut

Treesearch

J. W. Johnson

1950-01-01

Early, effects of partial cutting on diameter growth in bottomland hardwood forests have been measured recently near Vance, Mississippi, according to a report by J. W. Johnson of the Southern Forest Experiment Station, New Orleans, LA.

The Gesso Cut for Printmaking

ERIC Educational Resources Information Center

Kelly, Perry; Sarvis, Alva

1969-01-01

Directions are given for the preparation, cutting, and printing of a gesso board. A gesso cut is defined as a board coated with gesso into which a design has been impressed. The process is similar to the woodcut, but offers greater textural possibilities. (BF)

Killing, letting die and euthanasia.

PubMed Central

Husak, D N

1979-01-01

Medical ethicists debate whether or not the moral assessment of cases of euthanasia should depend on whether the patient is 'killed' or 'allowed to die'. The usual presupposition is that a clear distinction between killing and letting die can be drawn so that this substantive question is not begged. I contend that the categorisation of cases of instances of killing rather than as instances of letting die depends in part on a prior moral assessment of the case. Hence is it trivially rather than substantively true that the distinction has moral significance. But even if a morally neutral (ie non-question begging) distinction could be drawn, its application to the euthanasia controversy is problematic. I illustrate the difficulties of employing this distinction to reach moral conclusions by critically discussing Philippa Foot's recent treatment of euthanasia. I conclude that even if an act of euthanasia is an instance of killing, and there exists a prima facie moral duty not to kill, and no more stringent duty overrides this duty, one still cannot determine such an act to be morally impermissible. PMID:541821

Killing, letting die and euthanasia.

PubMed

Husak, D N

1979-12-01

Medical ethicists debate whether or not the moral assessment of cases of euthanasia should depend on whether the patient is 'killed' or 'allowed to die'. The usual presupposition is that a clear distinction between killing and letting die can be drawn so that this substantive question is not begged. I contend that the categorisation of cases of instances of killing rather than as instances of letting die depends in part on a prior moral assessment of the case. Hence is it trivially rather than substantively true that the distinction has moral significance. But even if a morally neutral (ie non-question begging) distinction could be drawn, its application to the euthanasia controversy is problematic. I illustrate the difficulties of employing this distinction to reach moral conclusions by critically discussing Philippa Foot's recent treatment of euthanasia. I conclude that even if an act of euthanasia is an instance of killing, and there exists a prima facie moral duty not to kill, and no more stringent duty overrides this duty, one still cannot determine such an act to be morally impermissible.

Death and Dying: Issues for Educational Gerontologists.

ERIC Educational Resources Information Center

Wass, Hannelore, Myers, Jane E.

1984-01-01

Reviews research on death orientations, the dying process, and bereavement, with a major focus on the elderly. Suggests that relevant knowledge about death and dying are important for gerontological practitioners and proposes that death-related content be systematically integrated into academic curricula at the preservice and inservice levels.…

Investigation of Cutting Quality of Remote DOE Laser Cutting in 0.5 mm Stainless Steel

NASA Astrophysics Data System (ADS)

Villumsen, Sigurd Lazic; Kristiansen, Morten

It has previously been shown that the stability of the remote fusion cutting (RFC) process can be increased by modifying the intensity profile of the laser by means of a diffractive optical element (DOE). This paper investigates the quality of remote DOE cutting (RDC) conducted with a 3 kW single mode fiber laser in 0.5 mm stainless steel. An automatic measurement system is used to investigate how the travel speed, focus offset and angle of incidence effect the kerf width and kerf variance. The study shows that the RDC process has a very low kerf width variance, and that the kerf width decreases with cutting speed. Furthermore, selected etched samples show a significant increase in the perpendicularity of the cuts when compared to RFC. Also, on average, the depth of the layer of molten material for RFC is 83% deeper than for RDC.

Kundenfokus: Startpunkt für die digitale Transformation bei Stadtwerken

NASA Astrophysics Data System (ADS)

Fett, Perry; Küller, Philipp

Big Data, Internet der Dinge, Mobile Computing und soziale Medien - die modernen Informationstechnologien durchdringen den Alltag der meisten Menschen und lösen hierdurch eine digitale Transformation aus. Im Unternehmenskontext manifestiert sich die Digitalisierung durch eine neue Qualität der wissensbasierten Entscheidungsunterstützung und der Automatisierung bzw. Autonomisierung der Geschäftsprozesse. Für Stadtwerke gilt es nun, die Chancen der Digitalisierung zu ihren Gunsten zu nutzen. Ein Startpunkt könnte hierbei sein, wie Stadtwerke zukünftig mit ihren Kunden interagieren. Ausgelöst durch die Liberalisierung der Märkte rückt der Kunde heute stärker in den Mittelpunkt - die Energiewirtschaft steht nun vor der Herausforderung, dem Wettbewerb einen Schritt voraus zu sein und dem Kunden ein absolut positives Kundenerlebnis (Customer Experience) sowohl als Maßnahme zur Kundenbindung als auch zum Kundenaufbau zu bieten. Das vorliegende Kapitel zeigt hierfür die Erfolgskriterien für die gelungene Etablierung des Kundenfokus im eigenen Unternehmen auf. Mit dem Customer-Focus-Cycle-Modell von Fujitsu, angelehnt an den Deming-Kreislauf, wird ein allgemeingültiger Ansatz für ein mögliches Vorgehen beim Aufbau des Kundenfokus vorgestellt. Die sechs Phasen werden dabei anhand praktischer Beispiele erläutert und geben zudem Hinweise zu Methoden und Tools. Aus dem vorgestellten "Werkzeugkasten" wird ferner die Customer-Journey-Methode im Detail erläutert. Weiter soll das präsentierte Reifegradmodell Unternehmen dabei unterstützen, den eigenen Status quo festzustellen und die persönlichen Ziele auf dem Weg zur kundenzentrierten Organisation festzulegen.

Finding minimum-quotient cuts in planar graphs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Park, J.K.; Phillips, C.A.

Given a graph G = (V, E) where each vertex v {element_of} V is assigned a weight w(v) and each edge e {element_of} E is assigned a cost c(e), the quotient of a cut partitioning the vertices of V into sets S and {bar S} is c(S, {bar S})/min{l_brace}w(S), w(S){r_brace}, where c(S, {bar S}) is the sum of the costs of the edges crossing the cut and w(S) and w({bar S}) are the sum of the weights of the vertices in S and {bar S}, respectively. The problem of finding a cut whose quotient is minimum for a graph hasmore » in recent years attracted considerable attention, due in large part to the work of Rao and Leighton and Rao. They have shown that an algorithm (exact or approximation) for the minimum-quotient-cut problem can be used to obtain an approximation algorithm for the more famous minimumb-balanced-cut problem, which requires finding a cut (S,{bar S}) minimizing c(S,{bar S}) subject to the constraint bW {le} w(S) {le} (1 {minus} b)W, where W is the total vertex weight and b is some fixed balance in the range 0 < b {le} {1/2}. Unfortunately, the minimum-quotient-cut problem is strongly NP-hard for general graphs, and the best polynomial-time approximation algorithm known for the general problem guarantees only a cut whose quotient is at mostO(lg n) times optimal, where n is the size of the graph. However, for planar graphs, the minimum-quotient-cut problem appears more tractable, as Rao has developed several efficient approximation algorithms for the planar version of the problem capable of finding a cut whose quotient is at most some constant times optimal. In this paper, we improve Rao`s algorithms, both in terms of accuracy and speed. As our first result, we present two pseudopolynomial-time exact algorithms for the planar minimum-quotient-cut problem. As Rao`s most accurate approximation algorithm for the problem -- also a pseudopolynomial-time algorithm -- guarantees only a 1.5-times-optimal cut, our algorithms represent a significant advance.« less

Finding minimum-quotient cuts in planar graphs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Park, J.K.; Phillips, C.A.

Given a graph G = (V, E) where each vertex v [element of] V is assigned a weight w(v) and each edge e [element of] E is assigned a cost c(e), the quotient of a cut partitioning the vertices of V into sets S and [bar S] is c(S, [bar S])/min[l brace]w(S), w(S)[r brace], where c(S, [bar S]) is the sum of the costs of the edges crossing the cut and w(S) and w([bar S]) are the sum of the weights of the vertices in S and [bar S], respectively. The problem of finding a cut whose quotient is minimummore » for a graph has in recent years attracted considerable attention, due in large part to the work of Rao and Leighton and Rao. They have shown that an algorithm (exact or approximation) for the minimum-quotient-cut problem can be used to obtain an approximation algorithm for the more famous minimumb-balanced-cut problem, which requires finding a cut (S,[bar S]) minimizing c(S,[bar S]) subject to the constraint bW [le] w(S) [le] (1 [minus] b)W, where W is the total vertex weight and b is some fixed balance in the range 0 < b [le] [1/2]. Unfortunately, the minimum-quotient-cut problem is strongly NP-hard for general graphs, and the best polynomial-time approximation algorithm known for the general problem guarantees only a cut whose quotient is at mostO(lg n) times optimal, where n is the size of the graph. However, for planar graphs, the minimum-quotient-cut problem appears more tractable, as Rao has developed several efficient approximation algorithms for the planar version of the problem capable of finding a cut whose quotient is at most some constant times optimal. In this paper, we improve Rao's algorithms, both in terms of accuracy and speed. As our first result, we present two pseudopolynomial-time exact algorithms for the planar minimum-quotient-cut problem. As Rao's most accurate approximation algorithm for the problem -- also a pseudopolynomial-time algorithm -- guarantees only a 1.5-times-optimal cut, our algorithms represent a significant advance.« less

Vee-notch tool cuts specimens

NASA Technical Reports Server (NTRS)

Spier, R. A.

1970-01-01

Triangular cutting tool uses carbide tips for notching heat-treated or abrasive materials, and alloys subjected to high structural stresses. The tool is rigidly mounted in a slot of mating contour to prevent deflection during cutting of tensile specimens. No other expensive machine equipment is required.

Indications of vigor loss after fire in Caribbean pine (Pinus caribaea) from electrical resistance measurements

Treesearch

T.E. Paysen; A.L. Koonce; E. Taylor; M.O. Rodriquez

2006-01-01

In May 1993, electrical resistance measurements were performed on trees in burned and unburned stands of Caribbean pine (Pinus caribaea Mor.) in north-eastern Nicaragua to determine whether tree vigor was affected by fire. An Osmose model OZ-67 Shigometer with digital readout was used to collect the sample electrical resistance data. Computer-...

Interrelationships among light, photosynthesis and nitrogen in the crown of mature Pinus contorta ssp. latifolia

Treesearch

A. W. Schoettle; W. K. Smith

1999-01-01

Scaling leaf-level measurements to estimate carbon gain of entire leaf crowns or canopies requires an understanding of the distribution of photosynthetic capacity and corresponding light microenvironments within a crown. We have compared changes in the photosynthetic light response and nitrogen (N) content (per unit leaf area) of Pinus contorta Dougl. ssp. latifolia...

Why do older people oppose physician-assisted dying? A qualitative study.

PubMed

Malpas, Phillipa J; Wilson, Maria K R; Rae, Nicola; Johnson, Malcolm

2014-04-01

Physician-assisted dying at the end of life has become a significant issue of public discussion. While legally available in a number of countries and jurisdictions, it remains controversial and illegal in New Zealand. The study aimed to explore the reasons some healthy older New Zealanders oppose physician-assisted dying in order to inform current debate. Recorded interviews were transcribed and analysed by the authors after some edits had been made by respondents. In all, 11 older participants (over 65 years) who responded to advertisements placed in Grey Power magazines and a University of Auckland email list were interviewed for around 1 h and asked a number of open-ended questions. Four central themes opposing physician-assisted dying were identified from the interviews: one's personal experience with health care and dying and death, religious reasoning and beliefs, slippery slope worries and concern about potential abuses if physician-assisted dying were legalised. An important finding of the study suggests that how some older individuals think about physician-assisted dying is strongly influenced by their past experiences of dying and death. While some participants had witnessed good, well-managed dying and death experiences which confirmed for them the view that physician-assisted dying was unnecessary, those who had witnessed poor dying and death experiences opposed physician-assisted dying on the grounds that such practices could come to be abused by others.

Modern laser technologies used for cutting textile materials

NASA Astrophysics Data System (ADS)

Isarie, Claudiu; Dragan, Anca; Isarie, Laura; Nastase, Dan

2006-02-01

With modern laser technologies we can cut multiple layers at once, yielding high production levels and short setup times between cutting runs. One example could be the operation of cutting the material named Nylon 66, used to manufacture automobile airbags. With laser, up to seven layers of Nylon 66 can be cut in one pass, that means high production rates on a single machine. Airbags must be precisely crafted piece of critical safety equipment that is built to very high levels of precision in a mass production environment. Of course, synthetic material, used for airbags, can be cut also by a conventional fixed blade system, but for a high production rates and a long term low-maintenance, laser cutting is most suitable. Most systems, are equipped with two material handling systems, which can cut on one half of he table while the finished product is being removed from the other half and the new stock material laid out. The laser system is reliable and adaptable to any flatbed-cutting task. Computer controlled industrial cutting and plotting machines are the latest offerings from a well established and experienced industrial engineering company that is dedicated to reduce cutting costs and boosting productivity in today's competitive industrial machine tool market. In this way, just one machine can carry out a multitude of production tasks. Authors have studied the cutting parameters for different textile materials, to reach the maximum output of the process.

Death and help expected from nurses when dying.

PubMed

Shih, Fu-Jin; Gau, Meei-Ling; Lin, Yaw-Sheng; Pong, Suang-Jing; Lin, Hung-Ru

2006-07-01

This project was undertaken to ascertain the perceptions of a group of Taiwan's fourth-year bachelor of science in nursing (BSN) students regarding death and help expected from nurses during the dying process. Within the Chinese culture, death is one of the most important life issues. However, in many Chinese societies it is difficult for people to reveal their deepest feelings to their significant others or loved ones. It was in this context that this project was developed because little is known about how Taiwan's nursing students perceive death and the dying process. Using an open-ended, self-report questionnaire, 110 senior BSN students recorded their thoughts on: (1) their fears before physical death; (2) afterlife destinations; and (3) the help they would expect from nurses when dying. The data were analyzed using a three-layer qualitative thematic analysis. The students' reported needs during the dying process were directed towards three main goals: (1) help in reaching the 'triple targets of individual life'; (2) help in facilitating in-depth support so that both the dying person and significant others can experience a blessed farewell; and (3) help in reaching a destination in the afterlife. The results support the belief of dying as a transition occurring when life weans itself from the mortal world and prepares for an afterlife.

Photodiode-based cutting interruption sensor for near-infrared lasers.

PubMed

Adelmann, B; Schleier, M; Neumeier, B; Hellmann, R

2016-03-01

We report on a photodiode-based sensor system to detect cutting interruptions during laser cutting with a fiber laser. An InGaAs diode records the thermal radiation from the process zone with a ring mirror and optical filter arrangement mounted between a collimation unit and a cutting head. The photodiode current is digitalized with a sample rate of 20 kHz and filtered with a Chebyshev Type I filter. From the measured signal during the piercing, a threshold value is calculated. When the diode signal exceeds this threshold during cutting, a cutting interruption is indicated. This method is applied to sensor signals from cutting mild steel, stainless steel, and aluminum, as well as different material thicknesses and also laser flame cutting, showing the possibility to detect cutting interruptions in a broad variety of applications. In a series of 83 incomplete cuts, every cutting interruption is successfully detected (alpha error of 0%), while no cutting interruption is reported in 266 complete cuts (beta error of 0%). With this remarkable high detection rate and low error rate, the possibility to work with different materials and thicknesses in combination with the easy mounting of the sensor unit also to existing cutting machines highlight the enormous potential for this sensor system in industrial applications.

Resin in bisulfite pulp from Pinus radiata wood and its relationship to pitch troubles

Treesearch

P.J. Nelson; Richard W. Hemingway

1971-01-01

The resin content of bisulfite pulp from Pinus radiata D. Don was determined at various stages in its manufacture and the changes in the composition of the resin studied. About 50% of the resin present in the wood was removed during cooking, an additional 11% by blowpit washing, and a further 8% by screening. Resin acids and fatty acids were...

Effect of plantation density on kraft pulp production from red pine (Pinus resinosa Ait.)

Treesearch

J.Y. Zhu; G.C. Myers

2006-01-01

Red pine (Pinus resinosa Ait.) butt logs from 38 year old research plots were used to study the effect of plantation stand density on kraft pulp production. Results indicate that plantation stand density can affect pulp yield, unrefined pulp mean fibre length, and the response of pulp fibre length to pulp refining. However, the effect of plantation stand density on...

Predicting age-age genetic correlations in tree-breeding programs: a case study of Pinus taeda L.

Treesearch

D.P. Gwaze; F.E. Bridgwater; T.D. Byram; J.A. Woolliams; C.G. Williams

2000-01-01

A meta-analysis of 520 parents and 51,439 individuals was used to develop two equations for predicting age-age genetic correlations in Pinus taeda L. Genetic and phenotypic family mean correlations and heritabilities were estimated for ages ranging from 2 to 25 years on 31...

Adjustments in hydraulic architecture of Pinus palustris maintain similar stomatal conductance in xerix and mesic habitats

Treesearch

R.N. Addington; L.A. Donovan; R.J. Mitchell; J.M. Vose; S.D. Pecot; S.B. Jack; U.G. Hacke; J.S. Sperry; R. Oren

2006-01-01

We investigated relationships between whole-tree hydranlic architecture and stomatal conductance in Pinus palustris Mill. (longleaf pine) across habitats that differed in soil properties and habitat structure. Trees occupying a xeric habitat (characterized by sandy, well-drained soils, higher nitrogen availability and lower overstory tree density)...

A Genetic Linkage Map of Longleaf Pine (Pinus palustris Mill.) Based on Random Amplified Polymorphic DNAs

Treesearch

C.D. Nelson; Thomas L. Kubisiak; M. Stine; W.L. Nance

1994-01-01

Eight megagametophyte DNA samples from a single longleaf pine (Pinus palustris Mill.) tree were used to screen 576 oligonucleotide primers for random amplified polymorphic DNA (RAPD) fragments. Primers amplifying repeatable polymorphic fragments were further characterized within a sample of 72 megagametophytes from the same tree. Fragments...

Nuclear genetic variation across the range of ponderosa pine (Pinus ponderosa): Phylogeographic, taxonomic and conservation implications

Treesearch

Kevin M. Potter; Valerie D. Hipkins; Mary F. Mahalovich; Robert E. Means

2015-01-01

Ponderosa pine (Pinus ponderosa) is among the most broadly distributed conifer species of western North America, where it possesses considerable ecological, esthetic, and commercial value. It exhibits complicated patterns of morphological and genetic variation, suggesting that it may be in the process of differentiating into distinct regional...

Plywood Inlays Thourgh CO2 Laser Cutting

NASA Astrophysics Data System (ADS)

Pires, Margarida C.; Araujo, J. L.; Teixeira, M. Ribau; Rodrigues, F. Carvalho

1989-07-01

Furniture with inlays is rather expensive. This is so on two accounts: Firstly, furniture with inlays is generally manufactured with solid wood.Secondly,wood carving and figure cutting are both time consuming and they produce a high rate of rejections. To add to it all the cutting and carving of minute figures requires an outstanding craftmanship. In fact the craftman is in most instance the artist and also the manufacturer. While desiring that the high artistic level is maintained in the industry the search for new method to produce inlays for furniture in not son expensive materials and to produce them in a repetitive and flexible way laser cutting of plywood was found to be quite suitable. This paper presents the charts for CO2 laser cutting of both positive and negatives in several types of plywood. The main problem is not so much the cutting of the positive and negatives pieces but to be able to cut the piece in a way that the fitting is done without any problems caused by the ever present charring effect, which takes palce at the edges of the cut pieces. To minimise this aspect positive and negative pieces have to be cut under stringent focusing conditions and with slight different scales. The condittions for our machine are presented.

Cascaded die mountings with spring-loaded contact-bond options

DOEpatents

Hsu, John S.; Adams, Donald J.; Su, Gui-Jia; Marlino, Laura D.; Ayers, Curtis W.; Coomer, Chester

2005-08-16

A cascaded die mounting device and method using spring contacts for die attachment, with or without metallic bonds between the contacts and the dies, is disclosed. One embodiment is for the direct refrigerant cooling of an inverter/converter carrying higher power levels than most of the low power circuits previously taught, and does not require using a heat sink.

Linking nonstructural carbohydrate dynamics to gas exchange and leaf hydraulic behavior in Pinus edulis and Juniperus monosperma

Treesearch

David R. Woodruff; Frederick C. Meinzer; Danielle E. Marias; Sanna Sevanto; Michael W. Jenkins; Nate G. McDowell

2014-01-01

Leaf hydraulics, gas exchange and carbon storage in Pinus edulis and Juniperus monosperma, two tree species on opposite ends of the isohydry–anisohydry spectrum, were analyzed to examine relationships between hydraulic function and carbohydrate dynamics.Leaf hydraulic vulnerability,...

Dominus for cut flower production

USDA-ARS?s Scientific Manuscript database

Fumigation with methyl bromide was the principal method of soilborne pest control in cut flower production. Many cut flower growers in Florida have ceased production, but those that remain are restricted in the fumigants that they are able to utilize due to proximity to potable water sources and oc...

Comparison of blood loss between using non central part cutting knee prosthesis and distal central part cutting.

PubMed

Malairungsakul, Anan

2014-12-01

Patients who undergo knee replacement surgery may need to receive a blood transfusion due to blood loss during the operation. Therefore it was important to improve the design of knee implant operative procedures in an attempt to reduce the rate of blood loss. The present study aimed to compare the blood loss between two types of knee replacement surgery. This is a retrospective study in which 78 patients received cemented knee replacements in Phayao Hospital between October 2010 and March 2012. There were two types of surgical procedure: 1) using an implant position covering the end of the femoral bone without cutting into the central part of the distal femoral, 2) using an implant position covering the end of the femoral bone cutting the central part of the distal femoral. Blood loss, blood transfusion, hemoglobin and hematocrit were recorded preoperatively, immediately postsurgery and 48 hours after surgery. Findings revealed that the knee replacement surgery using the implant position covering the end of the femoral bone without cutting the central part of the distal femoral significantly lowered the rate of blood loss when compared to using the implant position covering the end of the femoral bone with central cutting of the distal femor. The average blood loss during the operation without cutting at the central part of distal femoral was 49.50 ± 11.11 mL; whereas the operation cutting the central part of the distal femoral was 58.50 ± 11.69 mL. As regards blood loss, the knee replacement surgery using the implant position covering the end ofthefemoral bone without cutting the central part of distal femor was better than using the implant position covering the end of the femoral bone cutting at the central part of the distal femor.

25 CFR 301.3 - Specifications of dies.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 25 Indians 2 2010-04-01 2010-04-01 false Specifications of dies. 301.3 Section 301.3 Indians INDIAN ARTS AND CRAFTS BOARD, DEPARTMENT OF THE INTERIOR NAVAJO, PUEBLO, AND HOPI SILVER AND TURQUOISE... more mechanical than hand tools and vise. Dies shall contain only a single element of the design. ...

Commissioning a hobby cutting device for radiochromic film preparation.

PubMed

Zolfaghari, Somayeh; Francis, Kirby E; Kairn, Tanya; Crowe, Scott B

2017-06-01

In addition to a high spatial resolution and well characterised dose response, one of the major advantages of radiochromic film as a dosimeter is that sheets of film can be cut into pieces suitable for use as calibration films, and for in vivo and phantom measurements. The cutting of film is typically done using scissors or a guillotine, and this process can be time-consuming, limited in precision, requires extensive handling and does not allow holes to be cut from the film without cutting from an existing edge. This study investigated the use of a Brother ScanNCut hobby cutting system for EBT3 film preparation. The optimal operating parameters (blade size, pressure, speed) that resulted in precise cuts with minimal delamination at cut edges were identified using test cutting patterns. These parameters were then used to cut a large film insert for a stereotactic head phantom for comparison against an insert cut with scissors. While the hobby cutting system caused a wider region of delamination at the film edge (1.8 mm) compared to scissors (1 mm), the hobby cutting system was found to be able to produce reproducible cuts more efficiently and more accurately than scissors. The use of the hobby cutting system is recommended for complex phantom inserts (containing sharp corners or holes for alignment rods) or in situations where large numbers of film pieces need to be prepared.

Presettlement Pinus taeda in the Mississippi Valley Alluvial Plain of the Monroe County, Arkansas area

Treesearch

Don C. Bragg

2005-01-01

Loblolly pine (Pinus taeda) is the most dominant conifer in the southeastern United States (Baker and Langdon, 1990). However, loblolly pine was conspicuously absent from virtually the entire Mississippi Valley Alluvial Plain during presettlement times. A map (Fig. 1) of the native distribution of loblolly from Baker and Langdon (1990) identifies 2 exceptions to this...

Comparative genetic responses to climate in the varieties of Pinus ponderosa and Pseudotsuga menziesii: reforestation

Treesearch

Gerald E. Rehfeldt; Barry C. Jaquish; Cuauhtemoc Saenz-Romero; Dennis G. Joyce; Laura P. Leites; J. Bradley St Clair; Javier Lopez-Upton

2014-01-01

Impacts of climate change on the climatic niche of the sub-specific varieties of Pinus ponderosa and Pseudotsuga menziesii and on the adaptedness of their populations are considered from the viewpoint of reforestation. In using climate projections from an ensemble of 17 general circulation models targeting the decade surrounding 2060, our analyses suggest that a...

Hydraulic redistribution of water from Pinus ponderosa trees to seedlings: evidence for an ectomycorrhizal pathway.

Treesearch

Jeffrey M. Warren; J. Renee Brooks; Frederick C. Meinzer; Joyce L. Eberhart

2008-01-01

Although there is strong evidence for hydraulic redistribution (HR) of soil water by trees, it is not known if common myconhizal networks (CMN) can facilitate HR from mature trees to seedlings under field conditions. Ponderosa pine (Pinus ponderosa) seedlings were planted into root-excluding 61-micron mesh barrier chambers buried in an old-growth...

Growth in relation to canopy light interception in a red pine (Pinus resinosa) thinning study

Treesearch

Beverly E. Law; Kurt H. Riitters; Lewis F. Ohmann

1992-01-01

Growth data from the most recent 5 years of a 40-year thinning study in an even-aged red pine (Pinus resinosa) forest in cutfoot sioux experimental forest, Minnesota, were used with intercepted photosynthetically active radiation (IPAR) data to determine the relationship between light interception and growth for a range ofstand densities. Stand basal...