Power Plant Bromide Discharges and Downstream Drinking Water Systems in Pennsylvania.

PubMed

Good, Kelly D; VanBriesen, Jeanne M

2017-10-17

Coal-fired power plants equipped with wet flue gas desulfurization (FGD) systems have been implicated in increasing bromide levels and subsequent increases in disinfection byproducts at downstream drinking water plants. Bromide was not included as a regulated constituent in the recent steam electric effluent limitations guidelines and standards (ELGs) since the U.S. EPA analysis suggested few drinking water facilities would be affected by bromide discharges from power plants. The present analysis uses a watershed approach to identify Pennsylvania drinking water intakes downstream of wet FGD discharges and to assess the potential for bromide discharge effects. Twenty-two (22) public drinking water systems serving 2.5 million people were identified as being downstream of at least one wet FGD discharge. During mean August conditions (generally low-flow, minimal dilution) in receiving rivers, the median predicted bromide concentrations contributed by wet FGD at Pennsylvania intake locations ranged from 5.2 to 62 μg/L for the Base scenario (including only natural bromide in coal) and from 16 to 190 μg/L for the Bromide Addition scenario (natural plus added bromide for mercury control); ranges depend on bromide loads and receiving stream dilution capacity.

Validation of an automated fluorescein method for determining bromide in water

USGS Publications Warehouse

Fishman, M. J.; Schroder, L.J.; Friedman, L.C.

1985-01-01

Surface, atmospheric precipitation and deionized water samples were spiked with ??g l-1 concentrations of bromide, and the solutions stored in polyethylene and polytetrafluoroethylene bottles. Bromide was determined periodically for 30 days. Automated fluorescein and ion chromatography methods were used to determine bromide in these prepared samples. Analysis of the data by the paired t-test indicates that the two methods are not significantly different at a probability of 95% for samples containing from 0.015 to 0.5 mg l-1 of bromide. The correlation coefficient for the same sets of paired data is 0.9987. Recovery data, except for the surface water samples to which 0.005 mg l-1 of bromide was added, range from 89 to 112%. There appears to be no loss of bromide from solution in either type of container.Surface, atmospheric precipitation and deionized water samples were spiked with mu g l** minus **1 concentrations of bromide, and the solutions stored in polyethylene and polytetrafluoroethylene bottles. Bromide was determined periodically for 30 days. Automated fluorescein and ion chromatography methods were used to determine bromide in these prepared samples. Analysis of the data by the paired t-test indicates that the two methods are not significantly different at a probability of 95% for samples containing from 0. 015 to 0. 5 mg l** minus **1 of bromide. The correlation coefficient for the same sets of paired data is 0. 9987. Recovery data, except for the surface water samples to which 0. 005 mg l** minus **1 of bromide was added, range from 89 to 112%. Refs.

Methyl bromide: effective pest management tool and environmental threat.

PubMed

Thomas, W B

1996-12-01

Methyl bromide is used extensively on a global basis as a pesticide against nematodes, weeds, insects, fungi, bacteria, and rodents. As a soil fumigant, it is used in significant quantities in the production of strawberry and tomato, as well as other agriculture commodities. Grain, fresh fruit, forestry products, and other materials are fumigated with methyl bromide to control pest infestations during transport and storage. Structures also are treated with this chemical to control wood-destroying insects and rodents. However, methyl bromide has been identified as a significant ozone-depleting substance, resulting in regulatory actions being taken by the U.S. Environmental Protection Agency and the United Nations Environment Program (Montreal Protocol). The science linking methyl bromide to ozone depletion is strong and was reinforced by the 1994 UNEP Montreal Protocol Science Assessment on Ozone Depletion, which states, "Methyl bromide continues to be viewed as a significant ozone-depleting compound." Identifying efficacious and viable alternatives in the near term is critical.

The physicochemical properties of the low-temperature ionic liquid silver bromide-1-butyl-3-methylimidazolium bromide

NASA Astrophysics Data System (ADS)

Grishina, E. P.; Ramenskaya, L. M.; Pimenova, A. M.

2009-11-01

The physicochemical properties of the low-temperature ionic liquid based on 1-butyl-3-methylimidazolium bromide (BMImBr) and silver bromide were studied. Differential scanning calorimetry, Fourier transform IR spectroscopy, densimetry, viscometry, and conductometry measurements were performed to determine the dependences of the parameters under study on the concentration of AgBr. It was shown that the temperature and concentration behavior of the physicochemical properties of BMImBr-AgBr melts characterized the interaction between the system components with the formation of complex particles.

Comparison of Heat and Bromide as Ground Water Tracers Near Streams

USGS Publications Warehouse

Constantz, J.; Cox, M.H.; Su, G.W.

2003-01-01

Heat and bromide were compared as tracers for examining stream/ground water exchanges along the middle reaches of the Santa Clara River, California, during a 10-hour surface water sodium bromide injection test. Three cross sections that comprise six shallow (<1 m) piezometers were installed at the upper, middle, and lower sections of a 17 km long study reach, to monitor temperatures and bromide concentrations in the shallow ground water beneath the stream. A heat and ground water transport simulation model and a closely related solute and ground water transport simulation model were matched up for comparison of simulated and observed temperatures and bromide concentrations in the streambed. Vertical, one-dimensional simulations of sediment temperature were fitted to observed temperature results, to yield apparent streambed hydraulic conductivities in each cross section. The temperature-based hydraulic conductivities were assigned to a solute and ground water transport model to predict sediment bromide concentrations, during the sodium bromide injection test. Vertical, one-dimensional simulations of bromide concentrations in the sediments yielded a good match to the observed bromide concentrations, without adjustment of any model parameters except solute dispersivities. This indicates that, for the spatial and temporal scales examined on the Santa Clara River, the use of heat and bromide as tracers provide comparable information with respect to apparent hydraulic conductivities and fluxes for sediments near streams. In other settings, caution should be used due to differences in the nature of conservative (bromide) versus nonconservative (heat) tracers, particularly when preferential flowpaths are present.

Pyridostigmine bromide protection against acetylcholinesterase inhibition by pesticides.

PubMed

Henderson, John D; Glucksman, Gabriela; Leong, Bryan; Tigyi, Andras; Ankirskaia, Anna; Siddique, Imteaz; Lam, Helen; DePeters, Ed; Wilson, Barry W

2012-01-01

Pyridostigmine bromide (PB) has been used to protect soldiers from the toxic effects of soman, a chemical warfare agent. Recent research shows that pyridostigmine bromide protects a significant percentage of acetylcholinesterase in isolated human intercostal muscle. Findings presented here indicate that red blood cell acetylcholinesterase is similarly protected by pyridostigmine bromide from the action of diisopropyl fluorophosphate and several organophosphate pesticides including chlorpyrifos-oxon, diazinon-oxon, and paraoxon, but not malaoxon, using the bovine red blood cell as a subject. These findings suggest that pretreatment with PB may protect growers, farmworkers, first responders, and the public, in general, from the effects of selected pesticides. Copyright © 2011 Wiley Periodicals, Inc.

A practical comparison of Copper Bromide Laser for the treatment of vascular lesions.

PubMed

Lee, SunWoo; Lee, TaeBum; Kim, HoYoun; Kim, JungSoo; Eun, HyeJun; Kim, RyunKyung

2013-01-01

The recent rapid growth in demand for aesthetic non-invasive laser treatments such as unwanted skin rejuvenation, removal of age-related vascular blemishes has led to a boom in the medical devices to treat these conditions. Among diverse laser for skin treatment, copper bromide laser is a very effective, safe, and well tolerated treatment for facial telangiectasia at various energy levels and the most important thing of the copper bromide laser device is that the stability of the energy. However there is no evidence about effective copper bromide laser's energy level for the treatment of vascular lesions. We compared energy stability and treatment performance between two energy levels in 2 W and 8 W which commonly use in laser treatment for the vascular lesions. 8 W copper bromide laser was more stable compared than 2 W copper bromide laser. Also, 8 W copper bromide laser was effectively superior to 2 W copper bromide laser in treatment of vascular legion. Consequently, 8 W copper bromide laser treatment for vascular lesion might be more suitable than 2 W copper bromide laser.

Selective oxidation of bromide in wastewater brines from hydraulic fracturing.

PubMed

Sun, Mei; Lowry, Gregory V; Gregory, Kelvin B

2013-07-01

Brines generated from oil and natural gas production, including flowback water and produced water from hydraulic fracturing of shale gas, may contain elevated concentrations of bromide (~1 g/L). Bromide is a broad concern due to the potential for forming brominated disinfection byproducts (DBPs) during drinking water treatment. Conventional treatment processes for bromide removal is costly and not specific. Selective bromide removal is technically challenging due to the presence of other ions in the brine, especially chloride as high as 30-200 g/L. This study evaluates the ability of solid graphite electrodes to selectively oxidize bromide to bromine in flowback water and produced water from a shale gas operation in Southwestern PA. The bromine can then be outgassed from the solution and recovered, as a process well understood in the bromine industry. This study revealed that bromide may be selectively and rapidly removed from oil and gas brines (~10 h(-1) m(-2) for produced water and ~60 h(-1) m(-2) for flowback water). The electrolysis occurs with a current efficiency between 60 and 90%, and the estimated energy cost is ~6 kJ/g Br. These data are similar to those for the chlor-alkali process that is commonly used for chlorine gas and sodium hydroxide production. The results demonstrate that bromide may be selectively removed from oil and gas brines to create an opportunity for environmental protection and resource recovery. Copyright © 2013 Elsevier Ltd. All rights reserved.

Bromide's effect on DBP formation, speciation, and control; Part 1: Ozonation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shukairy, H.M.; Summers, R.S.; Miltner, R.J.

1994-06-01

The effect of variable ozone dosage and bromide concentration on the formation of organic disinfection by-products (DBPs) and bromate were evaluated. Low ozone dosages resulted in oxidation of organic precursors, yielding decreases in the formation potential for total trihalomethanes (THMs), six haloacetic acids (HAAs), and total organic halide (TOX). Increasing the ozone dosage oxidized bromide to bromate, decreasing the bromide for incorporation into DBPs. Bromate concentrations were linearly correlated with ozone residuals. Changes in the bromine incorporation factors n and n[prime] reflected differences in the resulting speciation of THMs and HAAs, respectively. Because TOX measurements based on chloride equivalence maymore » underestimate the halogenated DBP yield for high-bromide waters, a procedure is described whereby bromide and bromate concentrations were used to correct the TOX measurement.« less

Methyl bromide as a microbicidal fumigant for tree nuts.

PubMed Central

Schade, J E; King, A D

1977-01-01

Methyl bromide (MeBr) has broad microbicidal activity, but its use as a disinfectant for food is limited by the resulting bromide residues. Increasing the MeBr concentration, exposure temperature, or exposure period of a treatment tended to increase both the microbicidal efficacy of MeBr and the bromide residues. Its sporicidal activity was less at high than at low relative humidity within the range of 20 to 99%. Both the efficacy and the resulting residues of a MeBr treatment varied inversely with the load of product in a fumigation chamber due to sorption of the fumigant. Fumigation tests with almond kernels inoculated with Escherichia coli or Salmonella typhimurium indicated that MeBr can be used to disinfect whole nut kernels without resulting in excessive bromide residues, although the MeBr level necessary is higher than that normally used for insect control. PMID:406844

40 CFR 180.519 - Bromide ion and residual bromine; tolerances for residues.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Bromide ion and residual bromine... Tolerances § 180.519 Bromide ion and residual bromine; tolerances for residues. (a) General. The food additives, bromide ion and residual bromine, may be present in water, potable in accordance with the...

40 CFR 180.519 - Bromide ion and residual bromine; tolerances for residues.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 24 2011-07-01 2011-07-01 false Bromide ion and residual bromine... Tolerances § 180.519 Bromide ion and residual bromine; tolerances for residues. (a) General. The food additives, bromide ion and residual bromine, may be present in water, potable in accordance with the...

BROMIDE-OXIDANT INTERACTIONS AND THM (TRIHALOMETHANE) FORMATION: A LITERATURE REVIEW

EPA Science Inventory

The review focuses on the interactions, not only of bromide and chlorine, but also of bromide and two common oxidation alternatives to chlorine--chlorine dioxide and monochloramine. The data evaluations include discussions of reaction products, potentials for trihalomethane (THM)...

[Bioequivalence of pyridostigmine bromide dispersible tablets in rabbits].

PubMed

Wang, Hong; Wang, Hong; Tan, Qun-you; Zhang, Li; Cheng, Xun-guan; Zhang, Jing-qing

2011-10-01

To compare the pharmacokinetic parameters of pyridostigmine bromide dispersible tablets and common tablets in rabbits. Twelve rabbits were given an oral dose (60 mg) of pyridostigmine bromide dispersible tablets or common tablets in a randomized crossover study. The plasma concentration of pyridostigmine bromide was determined by reversed-phase ion pair chromatography. The pharmacokinetic parameters were calculated using DAS2.1.1 software. The pharmacokinetic parameters showed no significant differences in rabbit plasma between pyridostigmine bromide dispersible tablets and common tablets. The two tablets had a C(max) of 1.83∓0.08 mg·L(-1) and 1.68∓0.03 mg·L(-1), tmax of 2.33∓0.41 h and 2.58∓0.20 h, AUC(0-24) of 15.50∓0.62 mg·h·L(-1) and 15.14∓0.30 mg·h·L(-1), AUC(0-∞) of 15.82∓0.70 mg·h·L(-1) and 15.57∓0.32 mg·h·L(-1), respectively. The relative bioavailability F(0-24) was 102.38% and F(0-∞) was 101.61% for the dispersible tablets. The two tablets are bioequivalent in rabbits.

EFFECT OF BROMIDE ION IN WATER TREATMENT. 2. A LITERATURE REVIEW OF OZONE AND BROMIDE ION INTERACTIONS AND THE FORMATION OF ORGANIC BROMINE COMPOUNDS

EPA Science Inventory

Where bromide ion is found in water used as a source of drinking water, and chlorination is used for disinfection, bromide ion is oxidized to bromine and can result in the formation of organic bromine compounds. There are presently no treatment techniques available for economic r...

Thallium bromide radiation detectors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shah, K.S.; Lund, J.C.; Olschner, F.

1989-02-01

Radiation detectors have been fabricated from crystals of the semiconductor material thallium bromide (TlBr) and the performance of these detectors as room temperature photon spectrometers has been measured. These detectors exhibit improved energy resolution over previously reported TlBr detectors. These results indicate that TlBr is a very promising radiation detector material.

Automated determination of bromide in waters by ion chromatography with an amperometric detector

USGS Publications Warehouse

Pyen, G.S.; Erdmann, D.E.

1983-01-01

An automated ion chromatograph, including a program controller, an automatic sampler, an integrator, and an amperometric detector, was used to develop a procedure for the determination of bromide in rain water and many ground waters. Approximately 10 min is required to obtain a chromatogram. The detection limit for bromide is 0.01 mg l-1 and the relative standard deivation is <5% for bromide concentrations between 0.05 and 0.5 mg l-1. Chloride interferes if the chloride-to-bromide ratio is greater than 1 000:1 for a range of 0.01-0.1 mg l-1 bromide; similarly, chloride interferes in the 0.1-1.0 mg l-1 range if the ratio is greater than 5 000:1. In the latter case, a maximum of 2 000 mg l-1 of chloride can be tolerated. Recoveries of known concentrations of bromide added to several samples, ranged from 97 to 110%. ?? 1983.

The distribution of bromide in water in the Floridan aquifer system, Duval County, northeastern Florida

USGS Publications Warehouse

German, E.R.; Taylor, G.F.

1995-01-01

Although Duval County, Florida, has ample ground-water resources for public supply, the potential exists for a problem with excessive disinfectant by-products. These disinfectant by-products result from the treatment of raw water containing low concentrations of bromide and naturally occurring organic compounds. Because of this potential problem, the relation of bromide concentrations to aquifer tapped, well location and depth, and chemical characteristics of water in the Floridan aquifer system underlying Duval County were studied to determine if these relations could be applied to delineate water with low-bromide concentrations for future supplies. In 1992, water samples from 106 wells that tap the Floridan aquifer system were analyzed for bromide and major dissolved constituents. A comparison of bromide concentrations from the 1992 sampling with data from earlier studies (1979-80) indicates that higher bromide concentrations were detected during the earlier studies. The difference between the old and new data is probably because of a change in analytical methodology in the analysis of samples. Bromide concentrations exceeded the detection limit (0.10 milligrams per liter) in water from 28 of the 106 wells (26 percent) sampled in 1992. The maximum concentration was 0.56 milligrams per liter. There were no relations between bromide and major dissolved constituents, well depth, or aquifer tapped that would be useful for determining bromide concentrations. Areal patterns of bromide occurrence are not clearly defined, but areas with relatively high bromide concentrations tend to be located in a triangular area near the community of Sunbeam, Florida, and along the St. Johns River throughout Duval County.

An Ill Wind: Methyl Bromide Use Near California Schools, 1998.

ERIC Educational Resources Information Center

Ross, Zev; Walker, Bill

A California study investigates the use of the toxic pesticide methyl bromide near the state's public schools, explains why proposed safety rules have failed to protect children and others from exposure, and examines regions at particular exposure risk. Study results show an increasing exposure to methyl bromide near schools already at risk while…

Determination of methyl bromide in air samples by headspace gas chromatography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Woodrow, J.E.; McChesney, M.M.; Seiber, J.N.

1988-03-01

Methyl bromide is extensively used in agriculture (4 x 10/sup 6/ kg for 1985 in California alone as a fumigant to control nematodes, weeds, and fungi in soil and insect pests in harvested grains and nuts. Given its low boiling point (3.8/sup 0/C) and high vapor pressure (approx. 1400 Torr at 20/sup 0/C), methyl bromide will readily diffuse if not rigorously contained. Methods for determining methyl bromide and other halocarbons in air vary widely. A common practice is to trap the material from air on an adsorbent, such as polymeric resins, followed by thermal desorption either directly into the analyticalmore » instrumentation or after intermediary cryofocusing. While in some cases analytical detection limits were reasonable (parts per million range), many of the published methods were labor intensive and required special handling techniques that precluded high sample throughput. They describe here a method for the sampling and analysis of airborne methyl bromide that was designed to handle large numbers of samples through automating some critical steps of the analysis. The result was a method that allowed around-the-clock operation with a minimum of operator attention. Furthermore, the method was not specific to methyl bromide and could be used to determine other halocarbons in air.« less

Mepenzolate bromide promotes diabetic wound healing by modulating inflammation and oxidative stress

PubMed Central

Zheng, Yongjun; Wang, Xingtong; Ji, Shizhao; Tian, Song; Wu, Haibin; Luo, Pengfei; Fang, He; Wang, Li; Wu, Guosheng; Xiao, Shichu; Xia, Zhaofan

2016-01-01

Diabetic wounds are characterized by persistent inflammation and the excessive production of reactive oxygen species, thus resulting in impaired wound healing. Mepenzolate bromide, which was originally used to treat gastrointestinal disorders in clinical settings, has recently been shown to display beneficial effects in chronic obstructive pulmonary disease and pulmonary fibrosis of a mouse model by inhibiting inflammatory responses and reducing oxidative stress. However,the role of mepenzolate bromide in diabetic wound healing is still unclear. In this study, full-thickness excisional skin wounds were created on the backs of db/db mice, and mepenzolate bromide was topically applied to the wound bed. We found that mepenzolate bromide significantly promoted diabetic wound healing by measuring wound closure rate and histomorphometric analyses. Further studies showed that inflammation was inhibited by assessing the number of macrophages and levels of pro-inflammatory cytokines and pro-healing cytokines in the wounds. Furthermore, oxidative stress was reduced by monitoring the levels of MDA and H2O2 and the activities of glutathione peroxidase and catalase in the wounds. These results demonstrated the potential application of mepenzolate bromide for treating diabetic ulcers and other chronic wounds in clinics. PMID:27398156

Effectiveness of methyl bromide as a cargo fumigant for brown treesnakes

USGS Publications Warehouse

Savarie, P.J.; Wood, W.S.; Rodda, G.H.; Bruggers, R.L.; Engeman, R.M.

2005-01-01

The effectiveness of methyl bromide as a fumigant for brown treesnake (Boiga irregularis) management was evaluated on Guam. Eighteen snakes in secured cloth bags were randomly positioned in a 47.7-m3 tarpaulin-covered cargo container for each fumigation treatment. Methyl bromide treatments tested were: 24 g m−3 and and 12 g m−3, both for 2-h and 1-h exposures. All treatments, except for 12 g m−3 for 1 h, resulted in 100% mortality. Two-hour exposures to methyl bromide at 24 and 12 g m−3 appear to be effective in killing brown treesnakes within reasonable time-frames for shippers under Guam field conditions.

Comparison of the efficacy of preservative free ipratropium bromide and Atrovent nebuliser solution.

PubMed Central

Rafferty, P; Beasley, R; Holgate, S T

1988-01-01

The paradoxical bronchoconstriction observed with commercially available isotonic ipratropium bromide nebuliser solution (Atrovent) in patients with asthma results from an adverse reaction to the preservatives, benzalkonium chloride and ethylenediaminetetra-acetic acid (EDTA). The airway response to inhaled Atrovent and preservative free ipratropium bromide nebuliser solutions has been examined in a double blind study. On separate occasions 30 asthmatic subjects inhaled 2 ml of the solutions and airway calibre was measured in terms of FEV1 for 45 minutes. Atrovent nebuliser solution provoked a greater than 20% fall in FEV1 in five of the 30 subjects, whereas this did not occur after preservative free ipratropium bromide. Inhalation of the preservative free solution resulted in more rapid and greater overall bronchodilatation than Atrovent, with mean maximum increases in FEV1 of 29.2% and 18.5% respectively. It is concluded that the risk of paradoxical bronchoconstriction with ipratropium bromide is considerably reduced by removal of benzalkonium chloride and EDTA and that preservative free ipratropium bromide is a more potent bronchodilator than the currently available Atrovent solution. PMID:2971274

Chloride/bromide ratios in leachate derived from farm-animal waste.

PubMed

Hudak, Paul F

2003-01-01

Ratios of conservative chemicals have been used to identify sources of groundwater contamination. While chloride/bromide ratios have been reported for several common sources of groundwater contamination, little work has been done on leachate derived from farm-animal waste. In this study, chloride/bromide ratios were measured in leachate derived from longhorn-cattle, quarterhorse, and pygme-goat waste at a farm in Abilene, Texas, USA. (Minimum, median, and maximum) chloride/bromide ratios of (66.5, 85.6, and 167), (119, 146, and 156), and (35.4, 57.8, and 165) were observed for cattle, horses, and goats, respectively. These ratios are below typical values for domestic wastewater and within the range commonly observed for oilfield brine. Results of this study have important implications for identifying sources of contaminated groundwater in settings with significant livestock and/or oil production.

Subsurface drip application of alternative fumigants to methyl bromide for controlling nematodes in replanted grapevines.

PubMed

Cabrera, J Alfonso; Wang, Dong; Schneider, Sally M; Hanson, Bradley D

2012-05-01

Many California grape growers use preplant fumigation to ensure uniform and healthy grapevine establishment in replant situations. A field study was conducted to evaluate the performance of subsurface drip-applied chemical alternatives to methyl bromide on plant-parasitic nematodes, plant vigor and fruit yield during the 6 year period following replanting. Subsurface drip fumigation with 1,3-dichloropropene plus chloropicrin and with iodomethane plus chloropicrin had generally similar nematicide activity as methyl bromide in three grape types, while sodium azide was less effective. The combination of 1,3-dichloropropene plus chloropicrin enhanced vine vigor similarly to methyl bromide. However, all plots treated with alternative fumigants produced less fruit yield than methyl bromide over the 4 years of evaluation. Subsurface drip fumigation with alternative chemicals to methyl bromide generally provided adequate management of plant-parasitic nematodes during the vine establishment period. However, further research is required to increase the performance of alternative chemicals against other components of the replant problem, as grape yield in vines grown in the alternative treatments was lower than in methyl bromide. Copyright © 2011 Society of Chemical Industry.

Destruction of methyl bromide sorbed to activated carbon by thiosulfate and electrolysis

USDA-ARS?s Scientific Manuscript database

Methyl bromide is widely used as a fumigant for post-harvest and quarantine uses at port facilities due to the low treatment times required, but it is vented to the atmosphere after its use. Due to the potential contributions of methyl bromide to stratospheric ozone depletion, technologies for the c...

49 CFR 173.193 - Bromoacetone, methyl bromide, chloropicrin and methyl bromide or methyl chloride mixtures, etc.

Code of Federal Regulations, 2012 CFR

2012-10-01

... packaged as follows in wooden boxes (4C1, 4C2, 4D or 4F) with inner glass receptacles or tubes in... material. Total amount of liquid in the outer box must not exceed 11 kg (24 pounds). Packagings must... bromide mixtures containing up to 2% chloropicrin must be packaged in 4G fiberboard boxes with inside...

49 CFR 173.193 - Bromoacetone, methyl bromide, chloropicrin and methyl bromide or methyl chloride mixtures, etc.

Code of Federal Regulations, 2011 CFR

2011-10-01

... packaged as follows in wooden boxes (4C1, 4C2, 4D or 4F) with inner glass receptacles or tubes in... material. Total amount of liquid in the outer box must not exceed 11 kg (24 pounds). Packagings must... bromide mixtures containing up to 2% chloropicrin must be packaged in 4G fiberboard boxes with inside...

Stabilized thallium bromide radiation detectors and methods of making the same

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leao, Cedric Rocha; Lordi, Vincenzo

According to one embodiment, a crystal includes thallium bromide (TlBr), one or more positively charged dopants, and one or more negatively charged dopants. According to another embodiment, a system includes a monolithic crystal including thallium bromide (TlBr), one or more positively charged dopants, and one or more negatively charged dopants; and a detector configured to detect a signal response of the crystal.

Effects of ipratropium bromide and fenoterol aerosols in pulmonary emphysema.

PubMed Central

Hughes, J A; Tobin, M J; Bellamy, D; Hutchison, D C

1982-01-01

In patients with radiological evidence of pulmonary emphysema the bronchodilator drugs fenoterol and ipratropium bromide produced a considerable increase in vital capacity and reduction in residual volume. The response to fenoterol was virtually complete 15 minutes after administration, but after ipratropium bromide vital capacity was still increasing at 60 minutes. The change in vital capacity was slightly greater with a combination of the two drugs than with either used alone. Changes in FEV1 and peak flow rate were small. Images PMID:6218647

SYBR safeTM efficiently replaces ethidium bromide in Aspergillus fumigatus gene disruption.

PubMed

Canela, H M S; Takami, L A; Ferreira, M E S

2017-02-08

Invasive aspergillosis is a disease responsible for high mortality rates, caused mainly by Aspergillus fumigatus. The available drugs are limited and this disease continues to occur at an unacceptable frequency. Gene disruption is essential in the search for new drug targets. An efficient protocol for A. fumigatus gene disruption was described but it requires ethidium bromide, a genotoxic agent, for DNA staining. Therefore, the present study tested SYBR safe TM , a non-genotoxic DNA stain, in A. fumigatus gene disruption protocol. The chosen gene was cipC, which has already been disrupted successfully in our laboratory. A deletion cassette was constructed in Saccharomyces cerevisiae and used in A. fumigatus transformation. There was no statistical difference between the tested DNA stains. The success rate of S. cerevisiae transformation was 63.3% for ethidium bromide and 70% for SYBR safe TM . For A. fumigatus gene disruption, the success rate for ethidium bromide was 100 and 97% for SYBR safe TM . In conclusion, SYBR safe TM efficiently replaced ethidium bromide, making this dye a safe and efficient alternative for DNA staining in A. fumigatus gene disruption.

Effect of perfluorocarbon (perfluorooctyl bromide) vapor on tidal volume measurement during partial liquid ventilation.

PubMed

Davies, Mark W; Dunster, Kimble R

2002-05-01

To compare measured tidal volumes with and without perfluorocarbon (perfluorooctyl bromide) vapor, by using tidal volumes in the range suitable for neonates ventilated with partial liquid ventilation. We also aimed to determine the correction factor needed to calculate tidal volumes measured in the presence of perfluorooctyl bromide vapor. Prospective, experimental study. Neonatal research laboratory. Reproducible tidal volumes from 5 to 30 mL were produced with a rodent ventilator and drawn from humidifier chambers immersed in a water bath at 37 degrees C. Control tidal volumes were drawn from a chamber containing oxygen and water vapor, and the perfluorocarbon tidal volumes were drawn from a chamber containing oxygen, water vapor, and perfluorooctyl bromide vapor. Tidal volumes were measured by a VenTrak respiratory mechanics monitor with a neonatal flow sensor and a Dräger pneumotachometer attached to a Dräger neonatal ventilator. All tidal volumes measured with perfluorooctyl bromide vapor were increased compared with control. The VenTrak-measured tidal volumes increased by 1.8% to 3.5% (an overall increase of 2.2%). The increase was greater with the Dräger hot-wire anemometer: from 2.4% to 6.1% (an overall increase of 5.9%). Regression equations for mean control tidal volumes (response, Y) vs. mean perfluorooctyl bromide tidal volumes (predictor, X) are as follows: for the VenTrak, Y = -0.026 + (0.978 x X), r =.9999, p <.0001; and for the Dräger, Y = 0.251 + (0.944 x X), r =.9996, p <.0001. The presence of perfluorooctyl bromide vapor in the gas flowing through pneumotachometers gives falsely high tidal volume measurements. An estimate of the true tidal volume allowing for the presence of perfluorooctyl bromide vapor can be made from regression equations. Any calculation of lung mechanics must take into account the effect of perfluorooctyl bromide vapor on the measurement of tidal volume.

Effect of increasing bromide concentration on toxicity in treated drinking water.

PubMed

Sawade, Emma; Fabris, Rolando; Humpage, Andrew; Drikas, Mary

2016-04-01

Research is increasingly indicating the potential chronic health effects of brominated disinfection by-products (DBPs). This is likely to increase with elevated bromide concentrations resulting from the impacts of climate change, projected to include extended periods of drought and the sudden onset of water quality changes. This will demand more rigorous monitoring throughout distribution systems and improved water quality management at water treatment plants (WTPs). In this work the impact of increased bromide concentration on formation of DBPs following conventional treatment and chlorination was assessed for two water sources. Bioanalytical tests were utilised to determine cytotoxicity of the water post disinfection. Coagulation was shown to significantly reduce the cytotoxicity of the water, indicating that removal of natural organic matter DBP precursors continues to be an important factor in drinking water treatment. Most toxic species appear to form within the first half hour following disinfectant addition. Increasing bromide concentration across the two waters was shown to increase the formation of trihalomethanes and shifted the haloacetic acid species distribution from chlorinated to those with greater bromine substitution. This correlated with increasing cytotoxicity. This work demonstrates the challenges faced by WTPs and the possible effects increasing levels of bromide in source waters could have on public health.

Seeded Growth of Monodisperse Gold Nanorods Using Bromide-Free Surfactant Mixtures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ye, XC; Gao, YZ; Chen, J

We demonstrate for the first time that monodisperse gold nanorods (NRs) with broadly tunable dimensions and longitudinal surface plasmon resonances can be synthesized using a bromide-free surfactant mixture composed of alkyltrimethylammonium chloride and sodium oleate. It is found that uniform gold NRs can be obtained even with an iodide concentration approaching 100 mu M in the growth solution. In contrast to conventional wisdom, our results provide conclusive evidence that neither bromide as the surfactant counterion nor a high concentration of bromide ions in the growth solution is essential for gold NR formation. Correlated electron microscopy study of three-dimensional structures ofmore » gold NRs reveals a previously unprecedented octagonal prismatic structure enclosed predominantly by high index {310} crystal planes. These findings should have profound implications for a comprehensive mechanistic understanding of seeded growth of anisotropic metal nanocrystals.« less

Spectrophotometric estimation of bromide ion in excess chloride media.

PubMed

Adimurthy, S; Susarla, V R K S; Reddy, M P; Ramachandraiah, G

2005-10-31

The redox reaction between bromate and chloride ions in the presence and the absence of two or less equivalents of bromide ion ascertaining the formation of bromine chloride species of type BrCl and BrCl(2)(-) in subsequent reactions in 4% H(2)SO(4), has been studied by spectrophotometry. Calibration graphs for the bromide ion estimation in 0.1% KBrO(3)-4% H(2)SO(4) medium are determined separately in the presence of known amounts of NaCl. The effect of Cl(-) ion percentage on the determination of Br(-) ion is studied and reported herewith a suitable equation for a precise, reliable and quick spectrophotometric estimation.

Solid phase microextraction for active or passive sampling of methyl bromide during fumigations

USDA-ARS?s Scientific Manuscript database

The high diffusivity and volatility of methyl bromide make it an ideal compound for Solid Phase Micro Extraction (SPME)-based sampling of air prior to gas-chromatographic quantifications. SPME fibers can be used as active methyl bromide samplers, with high capacities and an equilibrium time of 1-2 m...

77 FR 35295 - Methyl Bromide; Pesticide Tolerances

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-13

.... SUMMARY: This regulation establishes a tolerance for residues of methyl bromide in or on cotton... on cotton, undelinted seed at 150 parts per million (ppm). EPA issued a proposed rule that explained... were accurate. According to USDA, drought conditions in Texas have reduced cotton production by 13...

Rocuronium Bromide Inhibits Inflammation and Pain by Suppressing Nitric Oxide Production and Enhancing Prostaglandin E2 Synthesis in Endothelial Cells.

PubMed

Baek, Sang Bin; Shin, Mal Soon; Han, Jin Hee; Moon, Sang Woong; Chang, Boksoon; Jeon, Jung Won; Yi, Jae Woo; Chung, Jun Young

2016-12-01

Rocuronium bromide is a nondepolarizing neuromuscular blocking drug and has been used as an adjunct for relaxation or paralysis of the skeletal muscles, facilitation of endotracheal intubation, and improving surgical conditions during general anesthesia. However, intravenous injection of rocuronium bromide induces injection pain or withdrawal movement. The exact mechanism of rocuronium bromide-induced injection pain or withdrawal movement is not yet understood. We investigated whether rocuronium bromide treatment is involved in the induction of inflammation and pain in vascular endothelial cells. For this study, calf pulmonary artery endothelial (CPAE) cells were used, and 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide assay, Western blot, nitric oxide detection, and prostaglandin E 2 immunoassay were conducted. Rocuronium bromide treatment inhibited endothelial nitric oxide synthase and suppressed nitric oxide production in CPAE cells. Rocuronium bromide activated cyclooxygenase-2, inducible nitric oxide synthase and increased prostaglandin E 2 synthesis in CPAE cells. Rocuronium bromide induced inflammation and pain in CPAE cells. Suppressing nitric oxide production and enhancing prostaglandin E 2 synthesis might be associated with rocuronium bromide-induced injection pain or withdrawal movement.

Comparison of phenobarbital with bromide as a first-choice antiepileptic drug for treatment of epilepsy in dogs.

PubMed

Boothe, Dawn Merton; Dewey, Curtis; Carpenter, David Mark

2012-05-01

To compare efficacy and safety of treatment with phenobarbital or bromide as the first-choice antiepileptic drug (AED) in dogs. Double-blinded, randomized, parallel, clinical trial. 46 AED-naïve dogs with naturally occurring epilepsy. Study inclusion was based on age, history, findings on physical and neurologic examinations, and clinicopathologic test results. For either phenobarbital treatment (21 dogs) or bromide treatment (25), a 7-day loading dose period was initiated along with a maintenance dose, which was adjusted on the basis of monthly monitoring. Efficacy and safety outcomes were compared between times (baseline and study end [generally 6 months]) and between drugs. Phenobarbital treatment resulted in eradication of seizures (17/20 [85%]) significantly more often than did bromide (12/23 [52%]); phenobarbital treatment also resulted in a greater percentage decrease in seizure duration (88 ± 34%), compared with bromide (49 ± 75%). Seizure activity worsened in 3 bromide-treated dogs only. In dogs with seizure eradication, mean ± SD serum phenobarbital concentration was 25 ± 6 μg/mL (phenobarbital dosage, 4.1 ± 1.1 mg/kg [1.9 ± 0.5 mg/lb], p.o., q 12 h) and mean serum bromide concentration was 1.8 ± 0.6 mg/mL (bromide dosage, 31 ± 11 mg/kg [14 ± 5 mg/lb], p.o., q 12 h). Ataxia, lethargy, and polydipsia were greater at 1 month for phenobarbital-treated dogs; vomiting was greater for bromide-treated dogs at 1 month and study end. Both phenobarbital and bromide were reasonable first-choice AEDs for dogs, but phenobarbital was more effective and better tolerated during the first 6 months of treatment.

Methyl Bromide Commodity Fumigation Buffer Zone Lookup Tables

EPA Pesticide Factsheets

Product labels for methyl bromide used in commodity and structural fumigation include requirements for buffer zones around treated areas. The information on this page will allow you to find the appropriate buffer zone for your planned application.

78 FR 32646 - Protection of Stratospheric Ozone: Request for Methyl Bromide Critical Use Exemption Applications...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-31

... being treated/produced. List how many mills have been fumigated with methyl bromide over the last three... facilities. Dried Cured Pork Applicants must list how many facilities have been fumigated with methyl bromide...

Residential proximity to methyl bromide use and birth outcomes in an agricultural population in California.

PubMed

Gemmill, Alison; Gunier, Robert B; Bradman, Asa; Eskenazi, Brenda; Harley, Kim G

2013-06-01

Methyl bromide, a fungicide often used in strawberry cultivation, is of concern for residents who live near agricultural applications because of its toxicity and potential for drift. Little is known about the effects of methyl bromide exposure during pregnancy. We investigated the relationship between residential proximity to methyl bromide use and birth outcomes. Participants were from the CHAMACOS (Center for the Health Assessment of Mothers and Children of Salinas) study (n = 442), a longitudinal cohort study examining the health effects of environmental exposures on pregnant women and their children in an agricultural community in northern California. Using data from the California Pesticide Use Reporting system, we employed a geographic information system to estimate the amount of methyl bromide applied within 5 km of a woman's residence during pregnancy. Multiple linear regression models were used to estimate associations between trimester-specific proximity to use and birth weight, length, head circumference, and gestational age. High methyl bromide use (vs. no use) within 5 km of the home during the second trimester was negatively associated with birth weight (β = -113.1 g; CI: -218.1, -8.1), birth length (β = -0.85 cm; CI: -1.44, -0.27), and head circumference (β = -0.33 cm; CI: -0.67, 0.01). These outcomes were also associated with moderate methyl bromide use during the second trimester. Negative associations with fetal growth parameters were stronger when larger (5 km and 8 km) versus smaller (1 km and 3 km) buffer zones were used to estimate exposure. Residential proximity to methyl bromide use during the second trimester was associated with markers of restricted fetal growth in our study.

Spectral characteristics of the bentonite loaded with benzyldimethyloctadecylammonium chloride, hexadecyltrimethylammonium bromide and dimethyldioctadecylammonium bromide

NASA Astrophysics Data System (ADS)

Majdan, Marek; Maryuk, Oksana; Gładysz-Płaska, Agnieszka; Pikus, Stanisław; Kwiatkowski, Ryszard

2008-02-01

The spectral characterization, including the FTIR, DRIFT (diffusive reflectance), SWAXS (small and wide angle X-ray scattering) spectra comparison of the sodium bentonite modified by BDMODA-Cl (benzyldimethyloctadecylammonium chloride), HDTMA-Br (hexadecyltrimethylammonium bromide), DDA-Br (dimethyldioctadecylammonium bromide) is presented in the paper. The FTIR spectra show the shift of C-H stretching vibrations: νsym(CH2), νasym(CH2) of surfactants methylene chains toward lower frequencies (from 2855 to 2851 cm -1 for νsym(CH2) and from 2927 to 2918 cm -1 for νansym(CH2) with the surfactant concentration in bentonite phase. The bending vibrations δH-O-H in water molecules change their positions in the direction of higher frequencies (from 1634 to 1647 cm -1) with the surfactant concentration for bentonite-BDMODA and bentonite-DDA contrary to bentonite-HDTMA, where the constant position δH-O-H is explained as the consequence of the lower concentration of the hydrogen bonded water in bentonite-HDTMA phase when compared with the remaining forms of bentonite. The DRIFT spectra reveal dramatic shift of the νSi-O stretching vibration toward higher frequencies upon intercalation of the sodium bentonite with the surfactant cations. The SWAXS spectra and SEM images of the bentonite are the evidence of somewhat different sorption mechanism of DDA-Br when compared with the BDMODA-Cl and HDTMA-Br, including remarkable external surface sorption contribution in the overall sorption.

76 FR 34700 - Protection of Stratospheric Ozone: Request for Methyl Bromide Critical Use Exemption Applications...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-14

... pest control methods. List how many mills have been fumigated with methyl bromide over the last three... been fumigated with methyl bromide over the last three years, rate, volume and target CT of methyl...

Formation of NDMA and halogenated DBPs by chloramination of tertiary amines: the influence of bromide ion.

PubMed

Le Roux, Julien; Gallard, Hervé; Croué, Jean-Philippe

2012-02-07

The formation of NDMA and other DBPs (including THMs, HANs, and HKs) has been investigated by chloramination of several tertiary amines in the absence and presence of bromide ion. NDMA formation from the most reactive tertiary amines (e.g., dimethylaminomethylfurfuryl alcohol or DMP30) was enhanced in the presence of bromide due to the formation of brominated oxidant species such as bromochloramine (NHBrCl) and the hypothetical UDMH-Br as an intermediate. The formation of NDMA by chloramination of less reactive model compounds was inhibited in the presence of bromide. This can be explained by competitive reactions leading to the production of brominated DBPs (i.e., THMs). In the presence of bromide, the formation of brominated THMs during chloramination can be attributed to the presence of small amounts of HOBr produced by the decomposition of chloramines and bromamines. The results are of particular interest to understand NDMA formation mechanisms, especially during chloramination of wastewaters impacted by anthropogenic tertiary amines and containing bromide ion.

Methyl bromide fumigation and delayed mortality: safe trade of live pests?

PubMed

Phillips, C B; Iline, I I; Novoselov, M; McNeill, M R; Richards, N K; van Koten, C; Stephenson, B P

Live organisms intercepted from treated commodities during phytosanitary inspections usually arouse suspicions of treatment failure, sub-standard treatment application, or post-treatment infestation. The additional possibility that some treatments could kill slowly, meaning commodities might be inspected before pests have succumbed, is seldom considered for treatments other than irradiation. We used a novel biochemical viability assay to measure delays between methyl bromide fumigation and mortality of dipteran eggs, and evaluated the correspondence between egg viability and egg morphological features. Our experimental conditions simulated shipping of rock melons from Australia to New Zealand by sea and air. No eggs survived fumigation, but they took 3-20 days to die, whereas phytosanitary inspections of rock melons occur within 2-7 days. Delays were not influenced by methyl bromide concentration, but were significantly lengthened by cooler storage temperatures. Methyl bromide's preservative effects delayed degradation of egg morphology, so the biochemical assay detected mortality long before morphological signs of egg death appeared. The results show that commodities subjected to effective methyl bromide treatments are at risk of being inspected before all pests have either died, or started to exhibit morphological signs of death. This could cause commodities to be unnecessarily rejected by quarantine authorities. Better methods than inspection for live pests are needed to assist authorities to gain assurance that treated commodities have been effectively disinfested. These could be developed by exploiting biochemical responses of pests and commodities to treatments.

Iron bromide vapor laser

NASA Astrophysics Data System (ADS)

Sukhanov, V. B.; Shiyanov, D. V.; Trigub, M. V.; Dimaki, V. A.; Evtushenko, G. S.

2016-03-01

We have studied the characteristics of a pulsed gas-discharge laser on iron bromide vapor generating radiation with a wavelength of 452.9 nm at a pulse repetition frequency (PRF) of 5-30 kHz. The maximum output power amounted to 10 mW at a PRF within 5-15 kHz for a voltage of 20-25 kV applied to electrodes of the discharge tube. Addition of HBr to the medium produced leveling of the radial profile of emission. Initial weak lasing at a wavelength of 868.9 nm was observed for the first time, which ceased with buildup of the main 452.9-nm line.

Evaluation of propargyl bromide for control of barnyardgrass and Fusarium oxysporum in three soils.

PubMed

Ma, Q; Gan, J; Becker, J O; Papiernik, S K; Yates, S R

2001-09-01

With the scheduled phasing out of methyl bromide, there is an urgent need for alternatives. We evaluated the efficacy of propargyl bromide as a potential replacement for methyl bromide for the control of barnyardgrass (Echinochloa crus-galli) and Fusarium oxysporum in an Arlington sandy loam, a Carsitas loamy sand and a Florida muck soil. Soil was mixed with barnyardgrass seeds or F oxysporum colonized on millet seeds, and treated with propargyl bromide at a range of concentrations. The mortality of the fungi and weed seeds was determined after 24 h of exposure at 30 degrees C. The concentrations required to inhibit 50% barnyard seed germination (LC50) were 2.8, 2.4 and 48.5 micrograms g-1 in the sandy loam, loamy sand and muck soil, respectively. In contrast, the LC50 values for F oxysporum were 11.2, 10.8 and 182.1 micrograms g-1 in the sandy loam, loamy sand and muck soil, respectively. The low efficacy of propargyl bromide in the muck soil was a result of the rapid degradation and high adsorption of the compound in the soil. The degradation half-life (t1/2) was only 7 h in the muck soil at an initial concentration of 6.8 micrograms g-1, compared to 60 and 67 h in the sandy loam and loamy sand, respectively. The adsorption coefficients (Kd) were 0.96, 0.87 and 5.6 cm3 g-1 in the sandy loam, loamy sand and muck soil, respectively. These results suggest that registration agencies should consider site-specific properties in recommending application rates for propargyl bromide.

Data for methyl bromide decon testing

EPA Pesticide Factsheets

Spreadsheets containing data for recovery of spores from different materials. Data on the fumigation parameters are also included.This dataset is associated with the following publication:Wood , J., M. Wendling, W. Richter, A. Lastivka, and L. Mickelsen. Evaluation of the Efficacy of Methyl Bromide in the Decontamination of Building and Interior Materials Contaminated with Bacillus anthracis Spores. APPLIED AND ENVIRONMENTAL MICROBIOLOGY. American Society for Microbiology, Washington, DC, USA, 1-28, (2016).

Prostate cancer and toxicity from critical use exemptions of methyl bromide: Environmental protection helps protect against human health risks

PubMed Central

2012-01-01

Background Although ozone-depleting methyl bromide was destined for phase-out by 2005, it is still widely applied as a consequence of various critical-use-exemptions and mandatory international regulations aiming to restrict the spread of pests and alien species (e.g. in globalized transport and storage). The withdrawal of methyl bromide because of its environmental risk could fortuitously help in the containment of its human toxicity. Methods We performed a systematic review of the literature, including in vitro toxicological and epidemiological studies of occupational and community exposure to the halogenated hydrocarbon pesticide methyl bromide. We focused on toxic (especially chronic) or carcinogenic effects from the use of methyl bromide, on biomonitoring data and reference values. Eligible epidemiological studies were subjected to meta-analysis. Results Out of the 542 peer reviewed publications between 1990-2011, we found only 91 referring to toxicity of methyl bromide and 29 using the term "carcinogenic", "neoplastic" or "mutagenic". Several studies provide new additional data pertaining to the mechanistic aspects of methyl bromide toxicity. Few studies have performed a detailed exposure assessment including biomonitoring. Three evaluated epidemiological studies assessed a possible association between cancer and methyl bromide. Overall, exposure to methyl bromide is associated with an increased risk of prostate cancer OR, 1.21; 95% CI (0,98-1.49), P = 0.076. Two epidemiological studies have analyzed environmental, non-occupational exposure to methyl bromide providing evidence for its health risk to the general public. None of the epidemiological studies addressed its use as a fumigant in freight containers, although recent field and case reports do refer to its toxic effects associated with its use in shipping and storage. Conclusions Both the epidemiological evidence and toxicological data suggest a possible link between methyl bromide exposure and serious

7 CFR 305.6 - Methyl bromide fumigation treatment schedules.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., fumigation with methyl bromide for sapote fruit fly. Regulated citrus fruits originating inside an area quarantined for sapote fruit fly that are to be moved outside the quarantined area may be treated with methyl...

Hydrogen bonding Part 53. Correlation of differential scanning calorimetric data with IR and dissociation vapor pressure studies of transitions of hexamethonium chloride and bromide dihydrates and hexamethonium bromide monohydrate

NASA Astrophysics Data System (ADS)

Snider, Barbara L.; Harmon, Kenneth M.

1994-03-01

Differential scanning calorimetry of hexamethonium chloride dihydrate shows an endothermic transition of 2.70 kcal mol -1 at 36.81°C. This correlates well with the temperatures observed by IR spectra (36°C) and equilibrium dissociation vapor pressure studies (37°C) for the transition between Type I planar cluster and Type II extended linear HOH⋯Cl - hydrogen bonding, and with the value of 2.77 kcal mol -1 for this transition derived by Hess' law treatment of dissociation vapor pressure data. Differential scanning calorimetry of hexamethonium bromide shows a rapid endothermic transition of 2.38 kcal mol -1 at 35.15°C and a very slow endothermic transition of about 12-13 kcal mol -1 centered near 50°C. This latter endotherm corresponds to the transition between Type I and Type II HOH⋯Br - hydrogen bonding observed by IR and vapor pressure studies at 49°C. The nature of the 35.15°C endotherm is not known. Hexamethonium bromide also shows a third endotherm at 142.91°C, which presumably results from melting of hydrate in the sealed DSC cell. Combined analysis of differential scanning calorimetry and dissociation vapor pressure data predicts a value of about -13 kcal mol -1 for an exothermic disproportionation at 52°C of two hexamethonium bromide monohydrate to Type II dihydrate and anhydrous bromide.

Nitroethylation of Vinyl Triflates and Bromides

PubMed Central

Padilla–Salinas, Rosaura; Walvoord, Ryan R.; Tcyrulnikov, Sergei

2013-01-01

A two-carbon homologation of vinyl triflates and bromides for the synthesis of homoallylic nitro products is described. This palladium-catalyzed double coupling of nitromethane exploits the anion stabilizing and leaving group properties of nitromethane, generating the homo allyl nitro products via a tandem cross-coupling/π-allylation sequence. The resultant process provides a mild and convenient entry of nitroethylated products, which are versatile precursors to β,γ-unsaturated carbonyls, homoallylic amines, and nitrile oxides. PMID:23885976

Bromide, Chloride, and Sulfate Concentrations, and Specific Conductance, Lake Texoma, Texas and Oklahoma, 2007-08

USGS Publications Warehouse

Baldys, Stanley

2009-01-01

The U.S. Geological Survey, in cooperation with the City of Dallas Water Utilities Division, collected water-quality data from 11 sites on Lake Texoma, a reservoir on the Texas-Oklahoma border, during April 2007-September 2008. At 10 of the sites, physical properties (depth, specific conductance, pH, temperature, dissolved oxygen, and alkalinity) were measured and samples were collected for analysis of selected dissolved constituents (bromide, calcium, magnesium, potassium, sodium, carbonate, bicarbonate, chloride, and sulfate); at one site, only physical properties were measured. The primary constituent of interest was bromide. Bromate can form when ozone is used to disinfect raw water containing bromide, and bromate is a suspected human carcinogen. Chloride and sulfate were of secondary interest. Only the analytical results for bromide, chloride, sulfate, and measured specific conductance are discussed in this report. Median dissolved bromide concentrations ranged from 0.28 to 0.60 milligrams per liter. The largest median dissolved bromide concentration (0.60 milligram per liter at site 11) was from the Red River arm of Lake Texoma. Dissolved bromide concentrations generally were larger in the Red River arm of Lake Texoma than in the Washita arm of the lake. Median dissolved chloride concentrations were largest in the Red River arm of Lake Texoma at site 11 (431 milligrams per liter) and smallest at site 8 (122 milligrams per liter) in the Washita arm. At site 11 in the Red River arm, the mean and median chloride concentrations exceeded the secondary maximum contaminant level of 300 milligrams per liter for chloride established by the 'Texas Surface Water Quality Standards' for surface-water bodies designated for the public water supply use. Median dissolved sulfate concentrations ranged from 182 milligrams per liter at site 4 in the Big Mineral arm to 246 milligrams per liter at site 11 in the Red River arm. None of the mean or median sulfate concentrations

[Preparation and quality control of pyridostigmine bromide orally disintegrating tablet].

PubMed

Zhang, Li; Tan, Qun-you; Cheng, Xun-guan; Wang, Hong; Hu, Ni-ni; Zhang, Jing-qing

2012-05-01

To prepare orally disintegrating tablets containing pyridostigmine bromide and optimize formulations. Solid dispersion was prepared using solvent evaporation-deposition method. The formulation was optimized by central composite design-response surface methodology (RSM plus CCD) with disintegration time as a reference parameter. The orally disintegrating tablets showed integrity and were smooth with desirable taste and feel in mouth. The disintegration time was less than 30 s. The cumulative drug dissolution was around 8.5% (around 2.5 mg which was less than bitterness threshold of pyridostigmine bromide of 3 mg) within 5 min in water while the cumulative drug dissolution was higher than 95% within 2 min in 0.1 N HCl. The orally disintegrating tablets are reasonable in formulation, feasible in technology and patient-friendly.

Active Control of Interface Shape During the Crystal Growth of Lead Bromide

NASA Technical Reports Server (NTRS)

Duval, W. M. B.; Batur, C.; Singh, N. B.

2003-01-01

A thermal model for predicting and designing the furnace temperature profile was developed and used for the crystal growth of lead bromide. The model gives the ampoule temperature as a function of the furnace temperature, thermal conductivity, heat transfer coefficients, and ampoule dimensions as variable parameters. Crystal interface curvature was derived from the model and it was compared with the predicted curvature for a particular furnace temperature and growth parameters. Large crystals of lead bromide were grown and it was observed that interface shape was in agreement with the shape predicted by this model.

Breakdown of ionic character of molecular alkali bromides in inner-valence photoionization

NASA Astrophysics Data System (ADS)

Karpenko, A.; Iablonskyi, D.; Urpelainen, S.; Kettunen, J. A.; Cao, W.; Huttula, M.; Aksela, H.

2014-05-01

The inner-valence region of alkali bromide XBr (X=Li, Na, K, Rb) vapours has been studied experimentally by means of synchrotron radiation excited photoelectron spectroscopy. Experimental spectra were analyzed by comparing them with available theoretical results and previous experiments. Ionic character of alkali bromides is seen to change in the inner-valence region with increasing atomic number of the alkali atom. A mechanism involving mixing between Br 4s and Rb 4p orbitals has been suggested to account for the fine structure observed in inner-valence ionization region of RbBr.

Pyridostigmine bromide versus fludrocortisone in the treatment of orthostatic hypotension in Parkinson's disease - a randomized controlled trial.

PubMed

Schreglmann, S R; Büchele, F; Sommerauer, M; Epprecht, L; Kägi, G; Hägele-Link, S; Götze, O; Zimmerli, L; Waldvogel, D; Baumann, C R

2017-04-01

Evidence for effective treatment options for orthostatic hypotension (OH) in Parkinson's disease (PD) is scarce. Elevation of cholinergic tone with pyridostigmine bromide has been reported as a way to improve blood pressure (bp) regulation in neurogenic hypotension without causing supine hypertension. This was a double-centre, double-blind, randomized, active-control, crossover, phase II non-inferiority trial of pyridostigmine bromide for OH in PD (clinicaltrials.gov NCT01993680). Patients with confirmed OH were randomized to 14 days 3 × 60 mg/day pyridostigmine bromide or 1 × 0.2 mg/day fludrocortisone before crossover. Outcome was measured by peripheral and central bp monitoring during the Schellong manoeuvre and questionnaires. Thirteen participants were enrolled between April 2013 and April 2015 with nine participants completing each trial arm. Repeated measures comparison showed a significant 37% improvement with fludrocortisone for the primary outcome diastolic bp drop on orthostatic challenge (baseline 22.9 ± 13.6 vs. pyridostigmine bromide 22.1 ± 17.0 vs. fludrocortisone 14.0 ± 12.6 mmHg; P = 0.04), whilst pyridostigmine bromide had no effect. Fludrocortisone caused an 11% peripheral systolic supine bp rise (baseline 128.4 ± 12.8 vs. pyridostigmine bromide 130.4 ± 18.3 vs. fludrocortisone 143.2 ± 10.1 mmHg; P = 0.01) but no central mean arterial supine bp rise (baseline 107.2 ± 7.8 vs. pyridostigmine bromide 97.0 ± 12.0 vs. fludrocortisone 107.3 ± 6.3 mmHg; P = 0.047). Subjective OH severity, motor score and quality of life remained unchanged by both study interventions. Pyridostigmine bromide is inferior to fludrocortisone in the treatment of OH in PD. This trial provides first objective evidence of the efficacy of 0.2 mg/day fludrocortisone for OH in PD, causing minor peripheral but no central supine hypertension. In addition to peripheral bp, future trials should include central bp measurements, known to correlate more closely with

A novel explicit approach to model bromide and pesticide transport in soils containing macropores

NASA Astrophysics Data System (ADS)

Klaus, J.; Zehe, E.

2011-01-01

The present study tests whether an explicit treatment of worm burrows is feasible for simulating water flow, bromide and pesticide transport in structured heterogeneous soils. The essence is to represent worm burrows as morphologically connected paths of low flow resistance in the spatially highly resolved model domain. A recent Monte Carlo study (Klaus and Zehe, 2010) revealed that this approach allowed successful reproduction of tile drain event discharge recorded during an irrigation experiment at a tile drained field site. However, several "hillslope architectures" that were all consistent with the available extensive data base allowed a good reproduction of tile drain flow response. Our second objective was thus to find out whether this "equifinality" in spatial model setups may be reduced when including bromide tracer data in the model falsification process. We thus simulated transport of bromide and Isoproturon (IPU) for the 13 spatial model setups, which performed best with respect to reproduce tile drain event discharge, without any further calibration. All model setups allowed a very good prediction of the temporal dynamics of cumulated bromide leaching into the tile drain, while only four of them matched the accumulated water balance and accumulated bromide loss into the tile drain. The number of behavioural model architectures could thus be reduced to four. One of those setups was used for simulating transport of IPU, using different parameter combinations to characterise adsorption according to the Footprint data base. Simulations could, however, only reproduce the observed leaching behaviour, when we allowed for retardation coefficients that were very close to one.

Detection of water contamination from hydraulic fracturing wastewater: a μPAD for bromide analysis in natural waters.

PubMed

Loh, Leslie J; Bandara, Gayan C; Weber, Genevieve L; Remcho, Vincent T

2015-08-21

Due to the rapid expansion in hydraulic fracturing (fracking), there is a need for robust, portable and specific water analysis techniques. Early detection of contamination is crucial for the prevention of lasting environmental damage. Bromide can potentially function as an early indicator of water contamination by fracking waste, because there is a high concentration of bromide ions in fracking wastewaters. To facilitate this, a microfluidic paper-based analytical device (μPAD) has been developed and optimized for the quantitative colorimetric detection of bromide in water using a smartphone. A paper microfluidic platform offers the advantages of inexpensive fabrication, elimination of unstable wet reagents, portability and high adaptability for widespread distribution. These features make this assay an attractive option for a new field test for on-site determination of bromide.

Chemical alternatives to methyl bromide for Florida ornamental production

USDA-ARS?s Scientific Manuscript database

This project is a cooperative effort among USDA, ARS and University of Florida researchers, Florida in-ground ornamental producers, and fumigant industry representatives. Funding is provided through the USDA-ARS Area-wide Pest Management Program for Alternatives to Methyl Bromide. The ornamental i...

A comparison between the gastric and salivary concentration of iodide, pertechnetate, and bromide in man

PubMed Central

Harden, R. McG.; Alexander, W. D.; Shimmins, J.; Chisholm, D.

1969-01-01

The concentration of iodide (I−) and pertechnetate (TcO4−) and bromide (Br−) has been measured simultaneously in gastric juice and parotid saliva. The combined gastric and salivary clearance for iodide and pertechnetate is more than twice the clearance of these ions by the thyroid gland. The concentration of the ions was in the order I−>TcO4−>Br− in both gastric juice and saliva. Differences exist between the secretion of iodide, pertechnetate, and bromide. Bromide, in contrast to iodide and pertechnetate, was found to be more concentrated in gastric juice than in saliva. The ratio of the iodide to pertechnetate clearance was greater in gastric juice than in saliva. PMID:5358585

Ease of intubation: A randomized, double-blind study to compare two doses of rocuronium bromide for endotracheal intubation.

PubMed

Shukla, Aparna; Misra, Shilpi

2016-01-01

Clinical need for a nondepolarizing agent with a rapid onset time and a brief duration of action has led to the development of rocuronium bromide. The aim of this study was to evaluate optimal dose of rocuronium bromide for intubation and to compare the onset time, duration of action, intubating conditions, and hemodynamic effects of two doses of rocuronium bromide. A prospective, randomized, double-blind study. All the patients were divided in a randomized, double-blind fashion into two groups of twenty patients each. Group I patients received rocuronium bromide 0.6 mg/kg intravenously and intubated at 60 s, Group II patients received rocuronium bromide 0.9 mg/kg and intubated at 60 s. The neuromuscular block was assessed using single twitch stimulation of 0.1 Hz at adductor pollicis muscle of hand at every 10 s. The results were compiled and analyzed statistically using Chi-square test for qualitative data and Student's t -test for quantitative data. Time of onset was significantly shorter ( P < 0.01) and duration of action was prolonged ( P < 0.001) for Group II as compared to Group I. The intubating conditions were (excellent + good) in 100% patients of Group II and (excellent + good) in 80% of Group I. There was no significant change in pulse rate and mean arterial pressure from the baseline value after the administration of muscle relaxants in either of the two groups. Rocuronium bromide 0.9 mg/kg is a safer alternative to rocuronium bromide 0.6 mg/kg for endotracheal intubation with shorter time of onset and better intubating conditions.

Bromidotetra-kis-(2-ethyl-1H-imidazole-κN (3))copper(II) bromide.

PubMed

Godlewska, Sylwia; Kelm, Harald; Krüger, Hans-Jörg; Dołęga, Anna

2012-12-01

The Cu(II) ion in the title mol-ecular salt, [CuBr(C5H8N2)4]Br, is coordinated in a square-pyramidal geometry by four N atoms of imidazole ligands and one bromide anion in the apical position. In the crystal, the ions are linked by N-H⋯Br hydrogen bonds involving both the coordinating and the free bromide species as acceptors. A C-H⋯Br inter-action is also observed. Overall, a three-dimensional network results.

Thermal decomposition mechanism of 1-ethyl-3-methylimidazolium bromide ionic liquid.

PubMed

Chambreau, Steven D; Boatz, Jerry A; Vaghjiani, Ghanshyam L; Koh, Christine; Kostko, Oleg; Golan, Amir; Leone, Stephen R

2012-06-21

In order to better understand the volatilization process for ionic liquids, the vapor evolved from heating the ionic liquid 1-ethyl-3-methylimidazolium bromide (EMIM(+)Br(-)) was analyzed via tunable vacuum ultraviolet photoionization time-of-flight mass spectrometry (VUV-PI-TOFMS) and thermogravimetric analysis mass spectrometry (TGA-MS). For this ionic liquid, the experimental results indicate that vaporization takes place via the evolution of alkyl bromides and alkylimidazoles, presumably through alkyl abstraction via an S(N)2 type mechanism, and that vaporization of intact ion pairs or the formation of carbenes is negligible. Activation enthalpies for the formation of the methyl and ethyl bromides were evaluated experimentally, ΔH(‡)(CH(3)Br) = 116.1 ± 6.6 kJ/mol and ΔH(‡)(CH(3)CH(2)Br) = 122.9 ± 7.2 kJ/mol, and the results are found to be in agreement with calculated values for the S(N)2 reactions. Comparisons of product photoionization efficiency (PIE) curves with literature data are in good agreement, and ab initio thermodynamics calculations are presented as further evidence for the proposed thermal decomposition mechanism. Estimates for the enthalpy of vaporization of EMIM(+)Br(-) and, by comparison, 1-butyl-3-methylimidazolium bromide (BMIM(+)Br(-)) from molecular dynamics calculations and their gas phase enthalpies of formation obtained by G4 calculations yield estimates for the ionic liquids' enthalpies of formation in the liquid phase: ΔH(vap)(298 K) (EMIM(+)Br(-)) = 168 ± 20 kJ/mol, ΔH(f, gas)(298 K) (EMIM(+)Br(-)) = 38.4 ± 10 kJ/mol, ΔH(f, liq)(298 K) (EMIM(+)Br(-)) = -130 ± 22 kJ/mol, ΔH(f, gas)(298 K) (BMIM(+)Br(-)) = -5.6 ± 10 kJ/mol, and ΔH(f, liq)(298 K) (BMIM(+)Br(-)) = -180 ± 20 kJ/mol.

A novel explicit approach to model bromide and pesticide transport in connected soil structures

NASA Astrophysics Data System (ADS)

Klaus, J.; Zehe, E.

2011-07-01

The present study tests whether an explicit treatment of worm burrows and tile drains as connected structures is feasible for simulating water flow, bromide and pesticide transport in structured heterogeneous soils at hillslope scale. The essence is to represent worm burrows as morphologically connected paths of low flow resistance in a hillslope model. A recent Monte Carlo study (Klaus and Zehe, 2010, Hydrological Processes, 24, p. 1595-1609) revealed that this approach allowed successful reproduction of tile drain event discharge recorded during an irrigation experiment at a tile drained field site. However, several "hillslope architectures" that were all consistent with the available extensive data base allowed a good reproduction of tile drain flow response. Our second objective was thus to find out whether this "equifinality" in spatial model setups may be reduced when including bromide tracer data in the model falsification process. We thus simulated transport of bromide for the 13 spatial model setups that performed best with respect to reproduce tile drain event discharge, without any further calibration. All model setups allowed a very good prediction of the temporal dynamics of cumulated bromide leaching into the tile drain, while only four of them matched the accumulated water balance and accumulated bromide loss into the tile drain. The number of behavioural model architectures could thus be reduced to four. One of those setups was used for simulating transport of Isoproturon, using different parameter combinations to characterise adsorption according to the Footprint data base. Simulations could, however, only reproduce the observed leaching behaviour, when we allowed for retardation coefficients that were very close to one.

Phase behavior of gemini surfactant hexylene-1,6-bis(dodecyldimethylammonium bromide) and polyelectrolyte NaPAA.

PubMed

Pi, Yingying; Shang, Yazhuo; Peng, Changjun; Liu, Honglai; Hu, Ying; Jiang, Jianwen

2006-07-01

The phase behavior of aqueous mixtures of gemini surfactant hexylene-1,6-bis(dodecyldimethylammonium bromide) (12-6-12) and oppositely charged polyelectrolyte sodium polyacrylate (NaPAA) has been studied experimentally. Compared to the mixtures of the traditional surfactant dodecyltrimethylammonium bromide (DTAB) and NaPAA, the gel phase region in the 12-6-12/NaPAA solution is larger. Element analysis reveals that NaPAA in the gel phase tends to replace the counterions of surfactant micelle and to release its own counterions. Spherical aggregates are observed in either top or bottom gel phase as detected by transmission electron microscopy. The addition of sodium bromide (NaBr) leads to a decrease in the gel phase region and the occurrence of a new cream phase.

Aluminum electroplating on steel from a fused bromide electrolyte

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prabhat K. Tripathy; Laura A. Wurth; Eric J. Dufek

A quaternary bromide bath (LiBr–KBr–CsBr–AlBr3) was used to electro-coat aluminum on steel substrates. The electrolytewas prepared by the addition of AlBr3 into the eutectic LiBr–KBr–CsBr melt. A smooth, thick, adherent and shiny aluminum coating could be obtained with 80 wt.% AlBr3 in the ternary melt. The SEM photographs of the coated surfaces suggest the formation of thick and dense coatings with good aluminum coverage. Both salt immersion and open circuit potential measurement suggested that the coatings did display a good corrosionresistance behavior. Annealing of the coated surfaces, prior to corrosion tests, suggested the robustness of the metallic aluminum coating inmore » preventing the corrosion of the steel surfaces. Studies also indicated that the quaternary bromide plating bath can potentially provide a better aluminumcoating on both ferrous and non-ferrous metals, including complex surfaces/geometries.« less

Aluminium Electroplating on Steel from a Fused Bromide Electrolyte

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prabhat Tripathy; Laura Wurth; Eric Dufek

A quaternary bromide bath (LiBr-KBr-CsBr-AlBr3) was used to electro-coat aluminium on steel substrates. The electrolyte was prepared by the addition of AlBr3 into the eutectic LiBr-KBr-CsBr melt. A smooth, thick, adherent and shiny aluminium coating could be obtained with 80 wt.% AlBr3 in the ternary melt. The SEM photographs of the coated surfaces suggest the formation of thick and dense coatings with good aluminium coverage. Both salt immersion and open circuit potential measurement suggest that the coatings did display good corrosion-resistance behavior. Annealing of the coated surfaces, prior to corrosion tests, suggested the robustness of the metallic aluminium coating inmore » preventing the corrosion of the steel surfaces. Studies also indicated that the quaternary bromide plating bath can potentially provide a better aluminium coating on both ferrous and non-ferrous metals, including complex surfaces/geometries.« less

Removal of bromide and iodide anions from drinking water by silver-activated carbon aerogels.

PubMed

Sánchez-Polo, M; Rivera-Utrilla, J; Salhi, E; von Gunten, U

2006-08-01

The aim of this study is to analyze the use of Ag-doped activated carbon aerogels for bromide and iodide removal from drinking water and to study how the activation of Ag-doped aerogels affects their behavior. It has been observed that the carbonization treatment and activation process of Ag-doped aerogels increased the surface area value ( [Formula: see text] ), whereas the volume of meso-(V(2)) and macropores (V(3)) decreased slightly. Chemical characterization of the materials revealed that carbonization and especially activation process considerably increased the surface basicity of the sample. Original sample (A) presented acidic surface properties (pH(PZC)=4.5) with 21% surface oxygen, whereas the sample that underwent activation showed mainly basic surface chemical properties (pH(PZC)=9.5) with only 6% of surface oxygen. Carbonization and especially, activation process considerable increased the adsorption capacity of bromide and iodide ions. This would mainly be produced by (i) an increase in the microporosity of the sample, which increases Ag-adsorption sites available to halide anions, and (ii) a rise of the basicity of the sample, which produces an increase in attractive electrostatic interactions between the aerogel surface, positively charged at the working pH (pH(solution)bromide and iodide was studied under dynamic conditions using waters from Lake Zurich. Results obtained showed that the carbonization and activation processes increased the adsorptive capacity of the aerogel sample. However, results showed that the adsorption capacity of the aerogel samples studied was considerably lower in water from Lake Zurich. Results showed X(0.02) (amount adsorbed to initial breakthrough) values of 0.1 and 4.3 mg/g for chloride anion and dissolved organic carbon (DOC), respectively, during bromide adsorption process in water from Lake Zurich

Methyl bromide phase out could affect future reforestation efforts

USDA-ARS?s Scientific Manuscript database

Methyl bromide has long been an integral component in producing healthy tree seedlings in forest nurseries of California, Idaho, Montana, Oregon and Washington. The fumigant was supposed to be completely phased out of use in the United States of America by 2005, but many forest nurseries continue to...

Utility of bromide and heat tracers for aquifer characterization affected by highly transient flow conditions

NASA Astrophysics Data System (ADS)

Ma, Rui; Zheng, Chunmiao; Zachara, John M.; Tonkin, Matthew

2012-08-01

A tracer test using both bromide and heat tracers conducted at the Integrated Field Research Challenge site in Hanford 300 Area (300A), Washington, provided an instrument for evaluating the utility of bromide and heat tracers for aquifer characterization. The bromide tracer data were critical to improving the calibration of the flow model complicated by the highly dynamic nature of the flow field. However, most bromide concentrations were obtained from fully screened observation wells, lacking depth-specific resolution for vertical characterization. On the other hand, depth-specific temperature data were relatively simple and inexpensive to acquire. However, temperature-driven fluid density effects influenced heat plume movement. Moreover, the temperature data contained "noise" caused by heating during fluid injection and sampling events. Using the hydraulic conductivity distribution obtained from the calibration of the bromide transport model, the temperature depth profiles and arrival times of temperature peaks simulated by the heat transport model were in reasonable agreement with observations. This suggested that heat can be used as a cost-effective proxy for solute tracers for calibration of the hydraulic conductivity distribution, especially in the vertical direction. However, a heat tracer test must be carefully designed and executed to minimize fluid density effects and sources of noise in temperature data. A sensitivity analysis also revealed that heat transport was most sensitive to hydraulic conductivity and porosity, less sensitive to thermal distribution factor, and least sensitive to thermal dispersion and heat conduction. This indicated that the hydraulic conductivity remains the primary calibration parameter for heat transport.

Utility of Bromide and Heat Tracers for Aquifer Characterization Affected by Highly Transient Flow Conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ma, Rui; Zheng, Chunmiao; Zachara, John M.

A tracer test using both bromide and heat tracers conducted at the Integrated Field Research Challenge site in Hanford 300 Area (300A), Washington, provided an instrument for evaluating the utility of bromide and heat tracers for aquifer characterization. The bromide tracer data were critical to improving the calibration of the flow model complicated by the highly dynamic nature of the flow field. However, most bromide concentrations were obtained from fully screened observation wells, lacking depth-specific resolution for vertical characterization. On the other hand, depth-specific temperature data were relatively simple and inexpensive to acquire. However, temperature-driven fluid density effects influenced heatmore » plume movement. Moreover, the temperature data contained “noise” caused by heating during fluid injection and sampling events. Using the hydraulic conductivity distribution obtained from the calibration of the bromide transport model, the temperature depth profiles and arrival times of temperature peaks simulated by the heat transport model were in reasonable agreement with observations. This suggested that heat can be used as a cost-effective proxy for solute tracers for calibration of the hydraulic conductivity distribution, especially in the vertical direction. However, a heat tracer test must be carefully designed and executed to minimize fluid density effects and sources of noise in temperature data. A sensitivity analysis also revealed that heat transport was most sensitive to hydraulic conductivity and porosity, less sensitive to thermal distribution factor, and least sensitive to thermal dispersion and heat conduction. This indicated that the hydraulic conductivity remains the primary calibration parameter for heat transport.« less

Influence of bromide on the performance of the amphipod Hyalella azteca in reconstituted waters

USGS Publications Warehouse

Ivey, Chris D.; Ingersoll, Christopher G.

2016-01-01

Poor performance of the amphipod Hyalella azteca has been observed in exposures using reconstituted waters. Previous studies have reported success in H. azteca water-only exposures with the addition of relatively high concentrations of bromide. The present study evaluated the influence of lower environmentally representative concentrations of bromide on the response ofH. azteca in 42-d water-only exposures. Improved performance of H. azteca was observed in reconstituted waters with >0.02 mg Br/L.

Effect of Methyl Bromide on Mycorrhizae and Growth of Sweetgum Seedlings

Treesearch

T. H. Filer; E. R. Toole

1968-01-01

Fumigation of nursery beds with methyl bromide improved sweetgum, growth by reducing the population of soil-inhabiting pathogens . Although mycorrhizal fungi were reduced, sufficient inoculum survived for rapid mycorrhizal development

The effects of pyridostigmine bromide and permethrin, alone or in combination, on response acquisition in male and female rats.

PubMed

Van Haaren, F; Cody, B; Hoy, J B; Karlix, J L; Schmidt, C J; Tebbett, I R; Wielbo, D

2000-08-01

It has been hypothesized that concurrent exposure to pyridostigmine bromide and permethrin may have contributed to the development of neurocognitive symptoms in Gulf War veterans. The present experiment was designed to investigate the effects of pyridostigmine bromide and permethrin alone, or in combination, on the acquisition of a novel response, one measure of normal cognitive functioning. Male and female Sprague-Dawley rats were treated with pyridostigmine bromide (1.5 mg/kg/day, by gavage in a volume of 5 ml/kg) or its vehicle for 7 consecutive days. They then also received an intraperitoneal injection of permethrin (0, 15, or 60 mg/kg) before they were exposed to an experimental session during which they could earn food by pressing a lever in an operant chamber. Serum permethrin levels increased as a function of its dose, and were higher in rats treated with pyridostigmine bromide. Sex differences were observed as permethrin levels were higher in female rats than in male rats following the highest dose. Pyridostigmine bromide delayed response acquisition in male and female rats, and resulted in higher response rates on the inactive lever in female rats than in male rats. Although permethrin levels were higher in subjects treated with pyridostigmine bromide than in those treated with vehicle, there were no differences in the behavioral effects of permethrin. Whether or not these behavioral effects of pyridostigmine bromide are of central or peripheral origin will need to be determined in future studies, as its effects on motor activity and/or gastro-intestinal motility may have affected response acquisition.

Examining the interrelationship between DOC, bromide and chlorine dose on DBP formation in drinking water--a case study.

PubMed

Bond, Tom; Huang, Jin; Graham, Nigel J D; Templeton, Michael R

2014-02-01

During drinking water treatment aqueous chlorine and bromine compete to react with natural organic matter (NOM). Among the products of these reactions are potentially harmful halogenated disinfection by-products, notably four trihalomethanes (THM4) and nine haloacetic acids (HAAs). Previous research has concentrated on the role of bromide in chlorination reactions under conditions of a given NOM type and/or concentration. In this study different concentrations of dissolved organic carbon (DOC) from U.K. lowland water were reacted with varying amounts of bromide and chlorine in order to examine the interrelationship between the three reactants in the formation of THM4, dihaloacetic acids (DHAAs) and trihaloacetic acids (THAAs). Results showed that, in general, molar yields of THM4 increased with DOC, bromide and chlorine concentrations, although yields did fluctuate versus chlorine dose. In contrast both DHAA and THAA yields were mainly independent of changes in bromide and chlorine dose at low DOC (1 mg·L(-1)), but increased with chlorine dose at higher DOC concentrations (4 mg·L(-1)). Bromine substitution factors reached maxima of 0.80, 0.67 and 0.65 for the THM4, DHAAs and THAAs, respectively, at the highest bromide/chlorine ratio studied. These results suggest that THM4 formation kinetics depend on both oxidation and halogenation steps, whereas for DHAAs and THAAs oxidation steps are more important. Furthermore, they indicate that high bromide waters may prove more problematic for water utilities with respect to THM4 formation than for THAAs or DHAAs. While mass concentrations of all three groups increased in response to increased bromide incorporation, only the THMs also showed an increase in molar yield. Overall, the formation behaviour of DHAA and THAA was more similar than that of THM4 and THAA. © 2013.

syn-Selective crotylation of aldehydes using bismuth-crotyl bromide-(1-butyl-3-methylimidazolium bromide) combination: some synthetic applications.

PubMed

Goswami, Dibakar; Koli, Mrunesh R; Chatterjee, Sucheta; Chattopadhyay, Subrata; Sharma, Anubha

2017-05-03

The Bi-[bmim][Br] combination has been found to offer high syn-selectivity in the crotylation of aldehydes with crotyl bromide using practically stoichiometric amounts of the reagents. The room temperature ionic liquid (RTIL), [bmim][Br], activated Bi metal in the presence of oxygen to produce crotylbismuthdibromide, which reacted with the aldehydes at room temperature. The major anti-syn diastereomeric product obtained from the crotylation of (R)-cyclohexylideneglyceraldehyde was utilized for the synthesis of dictyostatin and cryptophycin segments, and (+)-cis-aerangis lactone, using standard synthetic protocols.

REVIEW OF CONTROL OPTIONS FOR METHYL BROMIDE IN COMMODITY TREATMENT

EPA Science Inventory

The report describes recent developments in the control of methyl bromide (MeBr) and discusses technical considerations and requirements for and economic feasibility of recovery. (NOTE: MeBr, fumigant for agricultural commodities, is an ozone depleting chemical. The U.S. EPA has ...

Atmospheric volatilization of methyl bromide, 1,3-dichloropropene, and propargyl bromide through two plastic films: transfer coefficient and temperature effect

NASA Astrophysics Data System (ADS)

Wang, D.; Yates, S. R.; Gan, J.; Knuteson, J. A.

Atmospheric emission of methyl bromide (MeBr) and its potential alternative chemicals such as 1,3-dichloropropene (1,3-D) and propargyl bromide (PrBr) can contribute to air pollution and ozone depletion (for MeBr). One of the main sources of these chemicals is from agricultural soil fumigation. To understand the volatilization dynamics, emission of MeBr, 1,3-D, and PrBr through a polyethylene-based high-barrier film (HBF) and a virtually impermeable film (VIF) was measured using an air flow and sampling system that produced >90% mass balance. The experiment was conducted outdoors and was subjected to ambient daily temperature variations. The HBF film was found to be very permeable to 1,3-D and PrBr, but somewhat less permeable to MeBr. The VIF film was very impermeable to 1,3-D, PrBr, or MeBr. Measured volatilization flux, in general, exhibited strong diurnal variations which were controlled by film temperature. Unlike the HBF film, a time lag (˜12 h) was observed between high-temperatures and high-emission flux values for the VIF film. An impermeable film may be used as an effective means of controlling the atmospheric emission of MeBr and its alternative chemicals.

75 FR 5582 - Methyl Bromide; Amendments to Terminate Uses

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-03

... Table 2 to amend to terminate post-harvest methyl bromide uses in or on alfalfa hay and cottonseed for... registered for use on alfalfa hay and cotton seed in the United States. In the September 30, 2009 notice, EPA... distribution by the registrant of existing stocks labeled for post-harvest alfalfa hay and post-harvest...

40 CFR 180.123a - Inorganic bromide residues in peanut hay and peanut hulls; statement of policy.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 24 2011-07-01 2011-07-01 false Inorganic bromide residues in peanut hay and peanut hulls; statement of policy. 180.123a Section 180.123a Protection of Environment... RESIDUES IN FOOD Specific Tolerances § 180.123a Inorganic bromide residues in peanut hay and peanut hulls...

Effect of preconditioning on silver leaching and bromide removal properties of silver-impregnated activated carbon (SIAC).

PubMed

Rajaeian, Babak; Allard, Sébastien; Joll, Cynthia; Heitz, Anna

2018-07-01

Silver impregnated activated carbon (SIAC) has been found to be effective in mitigating the formation of brominated-disinfection by products during drinking water treatment. However, there are still uncertainties regarding its silver leaching properties, and strategies for the prevention of silver leaching have remained elusive. This study focused on the evaluation of one type of commercially available SIAC for its ability to remove bromide while minimising silver leaching from the material. Both synthetic and real water matrices were tested. Depending on solution pH, it was found that changing the surface charge properties of SIAC, as measured by the point of zero charge pH, can result in additional bromide removal while minimising the extent of silver leaching. To better understand the mechanism of silver leaching from the SIAC, eight preconditioning environments, i.e. variable pH and ionic strength were tested for a fixed amount of SIAC and two preconditioning environments were selected for a more detailed investigation. Experiments carried out in synthetic water showed that preconditioning at pH 10.4 did not deteriorate the capacity of SIAC to remove bromide, but significantly decreased the release of silver in the form of ionic silver (Ag + ), silver bromide (AgBr) and silver chloride (AgCl) from 40% for the pristine to 3% for the treated SIAC. This was confirmed using a groundwater sample. These results suggest that preconditioned SIAC has the potential to be an effective method for bromide removal with minimised silver leaching in a long-term field application for drinking water production. Copyright © 2018 Elsevier Ltd. All rights reserved.

Temperature Dependence of Mineral Solubility in Water. Part 2. Alkaline and Alkaline Earth Bromides

NASA Astrophysics Data System (ADS)

Krumgalz, B. S.

2018-03-01

Databases of alkaline and alkaline earth bromide solubilities in water at various temperatures were created using experimental data from publications over about the last two centuries. Statistical critical evaluation of the created databases was produced since there were enough independent data sources to justify such evaluation. The reliable experimental data were adequately described by polynomial expressions over various temperature ranges. Using the Pitzer approach for ionic activity and osmotic coefficients, the thermodynamic solubility products for the discussed bromide minerals have been calculated at various temperature intervals and also represented by polynomial expressions.

Cardiovascular effects of pancuronium bromide in mongrel dogs.

PubMed

Reitan, J A; Warpinski, M A

1975-09-01

The cardiovascular effects of a new nondepolarizing muscle relaxant, pancuronium bromide, were studied in mongrel dogs. Small, but significant, increases in mean arterial blood pressure were observed after each of 2 intravenous doses (0.01 mg/kg and 0.1 mg/kg) were given. Heart rate increased significantly in dogs administered the larger dosage, and indexes of ventricular functions demonstrated a trend toward positive cardiac inotrophy after either the large or the small dose.

BROMIDE'S EFFECT ON DBP FORMATION, SPECIATION, AND CONTROL: PART 1, OZONATION

EPA Science Inventory

The effect of variable ozone dosage and bromide concentration on the formation of organic disinfection byproducts (DBPs) and bromate were evaluated. Low ozone dosages resulted in oxidation of organic precursors, yielding decreases in the formation potential for total trihalometha...

Leisingera methylohalidivorans gen. nov., sp. nov., a marine methylotroph that grows on methyl bromide

USGS Publications Warehouse

Schaefer, J.K.; Goodwin, K.D.; McDonald, I.R.; Murrell, J.C.; Oremland, R.S.

2002-01-01

A marine methylotroph, designated strain MB2T, was isolated for its ability to grow on methyl bromide as a sole carbon and energy source. Methyl chloride and methyl iodide also supported growth, as did methionine and glycine betaine. A limited amount of growth was observed with dimethyl sulfide. Growth was also noted with unidentified components of the complex media marine broth 2216, yeast extract and Casamino acids. No growth was observed on methylated amines, methanol, formate, acetate, glucose or a variety of other substrates. Growth on methyl bromide and methyl iodide resulted in their oxidation to CO2 with stoichiometric release of bromide and iodide, respectively. Strain MB2T exhibited growth optima at NaCl and Mg2+ concentrations similar to that of seawater. Phylogenetic analysis of the 16S rDNA sequence placed this strain in the ??-Proteobacteria in proximity to the genera Ruegeria and Roseobacter. It is proposed that strain MB2T (= ATCC BAA-92T = DSM 14336T) be designated Leisingera methylohalidivorans gen. nov., sp. nov.

Study of the antibacterial and antifungal activities of synthetic benzyl bromides, ketones, and corresponding chalcone derivatives.

PubMed

Shakhatreh, Muhamad Ali K; Al-Smadi, Mousa L; Khabour, Omar F; Shuaibu, Fatima A; Hussein, Emad I; Alzoubi, Karem H

2016-01-01

Several applications of chalcones and their derivatives encouraged researchers to increase their synthesis as an alternative for the treatment of pathogenic bacterial and fungal infections. In the present study, chalcone derivatives were synthesized through cross aldol condensation reaction between 4-( N , N -dimethylamino)benzaldehyde and multiarm aromatic ketones. The multiarm aromatic ketones were synthesized through nucleophilic substitution reaction between 4-hydroxy acetophenone and benzyl bromides. The benzyl bromides, multiarm aromatic ketones, and corresponding chalcone derivatives were evaluated for their activities against eleven clinical pathogenic Gram-positive, Gram-negative bacteria, and three pathogenic fungi by the disk diffusion method. The minimum inhibitory concentration was determined by the microbroth dilution technique. The results of the present study demonstrated that benzyl bromide derivatives have strong antibacterial and antifungal properties as compared to synthetic chalcone derivatives and ketones. Benzyl bromides (1a and 1c) showed high ester activity against Gram-positive bacteria and fungi but moderate activity against Gram-negative bacteria. Therefore, these compounds may be considered as good antibacterial and antifungal drug discovery. However, substituted ketones (2a-b) as well as chalcone derivatives (3a-c) showed no activity against all the tested strains except for ketone (2c), which showed moderate activity against Candida albicans .

Study of the antibacterial and antifungal activities of synthetic benzyl bromides, ketones, and corresponding chalcone derivatives

PubMed Central

Shakhatreh, Muhamad Ali K; Al-Smadi, Mousa L; Khabour, Omar F; Shuaibu, Fatima A; Hussein, Emad I; Alzoubi, Karem H

2016-01-01

Several applications of chalcones and their derivatives encouraged researchers to increase their synthesis as an alternative for the treatment of pathogenic bacterial and fungal infections. In the present study, chalcone derivatives were synthesized through cross aldol condensation reaction between 4-(N,N-dimethylamino)benzaldehyde and multiarm aromatic ketones. The multiarm aromatic ketones were synthesized through nucleophilic substitution reaction between 4-hydroxy acetophenone and benzyl bromides. The benzyl bromides, multiarm aromatic ketones, and corresponding chalcone derivatives were evaluated for their activities against eleven clinical pathogenic Gram-positive, Gram-negative bacteria, and three pathogenic fungi by the disk diffusion method. The minimum inhibitory concentration was determined by the microbroth dilution technique. The results of the present study demonstrated that benzyl bromide derivatives have strong antibacterial and antifungal properties as compared to synthetic chalcone derivatives and ketones. Benzyl bromides (1a and 1c) showed high ester activity against Gram-positive bacteria and fungi but moderate activity against Gram-negative bacteria. Therefore, these compounds may be considered as good antibacterial and antifungal drug discovery. However, substituted ketones (2a–b) as well as chalcone derivatives (3a–c) showed no activity against all the tested strains except for ketone (2c), which showed moderate activity against Candida albicans. PMID:27877017

Reactive films for mitigating methyl bromide emissions from fumigated soil

USDA-ARS?s Scientific Manuscript database

Emissions of methyl bromide (MeBr) from agricultural fumigation can lead to depletion of the stratospheric ozone layer, and so its use is being phased out. However, as MeBr is still widely used under Critical Use Exemptions, strategies are still required to control such emissions. In this work, nove...

The oxidation of reduced nicotinamide nucleotides by hydrogen peroxide in the presence of lactoperoxidase and thiocyanate, iodide or bromide

PubMed Central

McC. Hogg, D.; Jago, G. R.

1970-01-01

Lactoperoxidase (EC 1.11.1.7) catalysed the oxidation of NADH by hydrogen peroxide in the presence of either thiocyanate, iodide or bromide. In the presence of thiocyanate, net oxidation of thiocyanate occurred simultaneously with the oxidation of NADH, but in the presence of iodide or bromide, only the oxidation of NADH occurred to a significant extent. In the presence of thiocyanate or bromide, NADH was oxidized to NAD+ but in the presence of iodide, an oxidation product with spectral and chemical properties distinct from NAD+ was formed. Thiocyanate, iodide and bromide appeared to function in the oxidation of NADH by themselves being oxidized to products which in turn oxidized NADH, rather than by activating the enzyme. Iodine, which oxidized NADH non-enzymically, appeared to be an intermediate in the oxidation of NADH in the presence of iodide. NADPH was oxidized similarly under the same conditions. An assessment was made of the rates of these oxidation reactions, together with the rates of other lactoperoxidase-catalysed reactions, at physiological concentrations of thiocyanate, iodide and bromide. The results indicated that in milk and saliva the oxidation of thiocyanate to a bacterial inhibitor was likely to predominate over the oxidation of NADH. PMID:4317722

Bromidotetra­kis­(2-ethyl-1H-imidazole-κN 3)copper(II) bromide

PubMed Central

Godlewska, Sylwia; Kelm, Harald; Krüger, Hans-Jörg; Dołęga, Anna

2012-01-01

The CuII ion in the title mol­ecular salt, [CuBr(C5H8N2)4]Br, is coordinated in a square-pyramidal geometry by four N atoms of imidazole ligands and one bromide anion in the apical position. In the crystal, the ions are linked by N—H⋯Br hydrogen bonds involving both the coordinating and the free bromide species as acceptors. A C—H⋯Br inter­action is also observed. Overall, a three-dimensional network results. PMID:23468738

Chromatographic method for the determination of diazepam, pyridostigmine bromide, and their metabolites in rat plasma and urine.

PubMed

Abu-Qare, A W; Abou-Donia, M B

2001-04-25

This study describes a chromatographic method for the determination of diazepam, an anxiolytic drug that is also used as an antidote against nerve agent seizures, its metabolites N-desmethyldiazepam, and temazepam, the anti-nerve agent drug pyridostigmine bromide (PB; 3-dimethylaminocarbonyloxy-N-methyl pyridinium bromide) and its metabolite N-methyl-3-hydroxypyridinium bromide in rat plasma and urine. The compounds were extracted using C18 Sep-Pak Vac 3cc (500 mg) cartridges and separated using isocratic mobile phase of methanol, acetonitrile and water (pH 3.2) (10:40:50) at a flow-rate of 0.5 ml/min in a period of 12 min, and UV detection ranging between 240 and 280 nm. The limits of detection for all analytes ranged between 20 and 50 ng/ml, while limits of quantitation were 100 ng/ml. Average percentage extraction recoveries of five spiked plasma samples were 79.1+/-7.7, 83.5+/-6.4, 83.9+/-5.9, 71.3+/-6.0 and 77.7+/-5.6, and from urine 79.4+/-7.9, 83.1+/-6.9, 73.6+/-7.7, 74.3+/-7.1 and 77.6+/-5.9 for diazepam, N-desmethyldiazepam, temazepam, pyridostigmine bromide, and N-methyl-3-hydroxypyridinium bromide, respectively. The relationship between peak areas and concentration was linear over the range between 100 and 1000 ng/ml. This method was applied to determine the above analytes following a single oral administration in rats as a tool to study the pharmacokinetic profile of each compound, alone and in combination.

Aerodynamic measurements of methyl bromide volatilization from tarped and nontarped fields

USGS Publications Warehouse

Majewski, M.S.; McChesney, M.M.; Woodrow, J.E.; Prueger, J.H.; Seiber, J.N.

1995-01-01

Methyl bromide (MeBr) is used extensively in agriculture as a soil fumigant and there is growing concern over the role it may play in the depletion of stratospheric ozone. Methyl bromide is applied using various techniques and very little is known about how much of the applied fumigant volatilizes into the atmosphere after the application. This held study was designed to estimate the post-application methyl bromide volatilization loss rates from two different application practices. The fields were approximately 6 km apart in Monterey County, California, and were treated in conformity with local practices as of 1992. The MeBr was injected at a depth of 25 to 30 cm. One field was covered simultaneously with a high-barrier plastic film tarp during the application, and the other was left uncovered, but the furrows made by the injection shanks were bedded over. Volatilization fluxes were estimated using an aerodynamic-gradient technique immediately following the completion of the application process and continued for 9 d for the tarped held and 6 d for the nontarped field. The cumulative volatilization losses from the tarped field were 22% of the nominal application within the first 5 d of the experiment and about 32% of the nominal application within 9 d including the one day after the tarp was removed on Day 8 after application. In contrast, the nontarped field lost 89% of the nominal application by volatilization in 5 d. The volatilization rate from the tarped field was shown to he significantly lower than the nontarped field at a 95% confidence level.

Carbene-catalysed reductive coupling of nitrobenzyl bromides and activated ketones or imines via single-electron-transfer process

PubMed Central

Li, Bao-Sheng; Wang, Yuhuang; Proctor, Rupert S. J.; Zhang, Yuexia; Webster, Richard D.; Yang, Song; Song, Baoan; Chi, Yonggui Robin

2016-01-01

Benzyl bromides and related molecules are among the most common substrates in organic synthesis. They are typically used as electrophiles in nucleophilic substitution reactions. These molecules can also be activated via single-electron-transfer (SET) process for radical reactions. Representative recent progress includes α-carbon benzylation of ketones and aldehydes via photoredox catalysis. Here we disclose the generation of (nitro)benzyl radicals via N-heterocyclic carbene (NHC) catalysis under reductive conditions. The radical intermediates generated via NHC catalysis undergo formal 1,2-addition with ketones to eventually afford tertiary alcohol products. The overall process constitutes a formal polarity-inversion of benzyl bromide, allowing a direct coupling of two initially electrophilic carbons. Our study provides a new carbene-catalysed reaction mode that should enable unconventional transformation of (nitro)benzyl bromides under mild organocatalytic conditions. PMID:27671606

Carbene-catalysed reductive coupling of nitrobenzyl bromides and activated ketones or imines via single-electron-transfer process

NASA Astrophysics Data System (ADS)

Li, Bao-Sheng; Wang, Yuhuang; Proctor, Rupert S. J.; Zhang, Yuexia; Webster, Richard D.; Yang, Song; Song, Baoan; Chi, Yonggui Robin

2016-09-01

Benzyl bromides and related molecules are among the most common substrates in organic synthesis. They are typically used as electrophiles in nucleophilic substitution reactions. These molecules can also be activated via single-electron-transfer (SET) process for radical reactions. Representative recent progress includes α-carbon benzylation of ketones and aldehydes via photoredox catalysis. Here we disclose the generation of (nitro)benzyl radicals via N-heterocyclic carbene (NHC) catalysis under reductive conditions. The radical intermediates generated via NHC catalysis undergo formal 1,2-addition with ketones to eventually afford tertiary alcohol products. The overall process constitutes a formal polarity-inversion of benzyl bromide, allowing a direct coupling of two initially electrophilic carbons. Our study provides a new carbene-catalysed reaction mode that should enable unconventional transformation of (nitro)benzyl bromides under mild organocatalytic conditions.

Physicochemical and in vitro deposition properties of salbutamol sulphate/ipratropium bromide and salbutamol sulphate/excipient spray dried mixtures for use in dry powder inhalers.

PubMed

Corrigan, Deirdre O; Corrigan, Owen I; Healy, Anne Marie

2006-09-28

The physicochemical and aerodynamic properties of spray dried powders of the drug/drug mixture salbutamol sulphate/ipratropium bromide were investigated. The in vitro deposition properties of spray dried salbutamol sulphate and the spray dried drug/excipient mixtures salbutamol sulphate/lactose and salbutamol sulphate/PEG were also determined. Spray drying ipratropium bromide monohydrate resulted in a crystalline material from both aqueous and ethanolic solution. The product spray dried from aqueous solution consisted mainly of ipratropium bromide anhydrous. There was evidence of the presence of another polymorphic form of ipratropium bromide. When spray dried from ethanolic solution the physicochemical characterisation suggested the presence of an ipratropium bromide solvate with some anhydrous ipratropium bromide. Co-spray drying salbutamol sulphate with ipratropium bromide resulted in amorphous composites, regardless of solvent used. Particles were spherical and of a size suitable for inhalation. Twin impinger studies showed an increase in the fine particle fraction (FPF) of spray dried salbutamol sulphate compared to micronised salbutamol sulphate. Co-spray dried salbutamol sulphate:ipratropium bromide 10:1 and 5:1 systems also showed an increase in FPF compared to micronised salbutamol sulphate. Most co-spray dried salbutamol sulphate/excipient systems investigated demonstrated FPFs greater than that of micronised drug alone. The exceptions to this were systems containing PEG 4000 20% or PEG 20,000 40% both of which had FPFs not significantly different from micronised salbutamol sulphate. These two systems were crystalline unlike most of the other spray dried composites examined which were amorphous in nature.

Pharmacodynamic Comparison of Rocuronium Bromide between Patients from the Plateau Area and from the Plain Area.

PubMed

Xie, Min; Huang, Jianxin; Li, Peng; Ou, Zhiyan; Hou, Jing

2016-06-23

We aimed to conduct a pharmacodynamic comparison of rocuronium bromide between patients from the plateau area and from the plain area. A total of 104 patients who received laparoscopic cholecystectomy in Sichuan Provincial People's Hospital and Aba Autonomous Prefecture People's Hospital from October 2015 to December 2015 were included in this study. Among them, 46 patients were from the plateau area and 58 were from the plain area. Both groups received total intravenous anesthesia (TIVA) with a dose of 0.6mg/kg rocuronium bromide during induction. In the meantime, neuromuscular block was monitored using a train-of-four (TOF) stimulation mode. The onset time (time to achieve the lowest TOF value after the injection of rocuronium bromide), duration of maximal neuromuscular block (duration of lowest T1 value), time to 25% recovery, time to 75% recovery, recovery index (time from 25% recovery to 75% recovery), time to extubation, length of stay in Post Anesthesia Care Unit (PACU) and muscle strength upon PACU discharge were all recorded. The onset time, time to 25% recovery, time to 75% recovery and time to extubation were all significantly prolonged in patients from the plateau area after receiving one single dose of rocuronium bromide (P<0.05). However, both groups didn't show any significant difference in maximal neuromuscular block, recovery index (time from 25% recovery to 75% recovery), length of stay in PACU or muscle strength upon PACU discharge (P>0.05). Compared to patients from the plain area, patients from the plateau area showed prolonged onset time of rocuronium bromide, reduced metabolic capabilities and longer duration of muscular relaxation. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Metabolism of proposed nerve agent pretreatment, pyridostigmine bromide. Final report, December 1995-December 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leo, K.U.

A reverse phase High Pressure Liquid Chromatography (HPLC) method was developed to separate pyridostigmine bromide from four potential metabolites. Using male and female microsomes from both rat and human, our data suggest that pyridostigmine bromide is not metabolized by the human live microsomes or DNA expressed human CYP-450s via direct observation of no metabolites being formed for incubations up to 90 minutes. Indirect evidence that pyridostigmine metabolism is not via the major human hepatic CYP-450s involved in drug metabolism, 1A2, 2C9, 2E1, 2D6, and 3A4, was observed by failure to inhibit these isozymes while co-incubated with substrates specific for thosemore » isozymes at concentrations of 2-3 times Km. The following CYP-450 substrates were co-incubated with pyridostigmine: phenacetin, tolbutamide, chlorzoxazone, bufuralol, and testosterone. Using unlabelled and 14C-pyridostigmine, metabolite formation was not observed in both male and female rat and human subcellular fractions, specifically cytosol and S9, or under conditions favoring human FMO activity (pH 8.3). These findings indicate the metabolism of pyridostigmine bromide is unlikely to be under any component of sexual dimorphism.« less

Toxic impact of bromide and iodide on drinking water disinfected with chlorine or chloramines.

PubMed

Yang, Yang; Komaki, Yukako; Kimura, Susana Y; Hu, Hong-Ying; Wagner, Elizabeth D; Mariñas, Benito J; Plewa, Michael J

2014-10-21

Disinfectants inactivate pathogens in source water; however, they also react with organic matter and bromide/iodide to form disinfection byproducts (DBPs). Although only a few DBP classes have been systematically analyzed for toxicity, iodinated and brominated DBPs tend to be the most toxic. The objectives of this research were (1) to determine if monochloramine (NH2Cl) disinfection generated drinking water with less toxicity than water disinfected with free chlorine (HOCl) and (2) to determine the impact of added bromide and iodide in conjunction with HOCl or NH2Cl disinfection on mammalian cell cytotoxicity and genomic DNA damage induction. Water disinfected with chlorine was less cytotoxic but more genotoxic than water disinfected with chloramine. For both disinfectants, the addition of Br(-) and I(-) increased cytotoxicity and genotoxicity with a greater response observed with NH2Cl disinfection. Both cytotoxicity and genotoxicity were highly correlated with TOBr and TOI. However, toxicity was weakly and inversely correlated with TOCl. Thus, the forcing agents for cytotoxicity and genotoxicity were the generation of brominated and iodinated DBPs rather than the formation of chlorinated DBPs. Disinfection practices need careful consideration especially when using source waters containing elevated bromide and iodide.

Maintaining Flatness of a Large Aperture Potassium Bromide Beamsplitter Through Mounting and Vibration

NASA Technical Reports Server (NTRS)

Losch, Patricia; Lyons, James J., III; Morell, Armando; Heaney, Jim

1998-01-01

The Composite Infrared Spectrometer (CIRS) instrument on the Cassini Mission launched in October of 1997. The CIRS instrument contains a mid-infrared (MIR) and a far-infrared interferometer (FIR) and operates at 170 Kelvin. The MIR is a Michelson Fourier transform spectrometer utilizing a 76 mm (3 inch) diameter potassium bromide beamsplitter and compensator pair. The potassium bromide elements were tested to verify effects of cooldown and vibration prior to integration into the instrument. The instrument was then aligned at ambient temperatures, tested cryogenically and re-verified after vibration. 'Me stringent design optical figure requirements for the beamsplitter and compensator included fabrication errors, mounting stresses and vibration load effects. This paper describes the challenges encountered in mounting the elements to minimize distortion and to survive vibration.

Maintaining Flatness of a Large Aperture Potassium Bromide Beamsplitter through Mounting and Vibration

NASA Technical Reports Server (NTRS)

Losch, Patricia; Lyons, James, III; Morell, Armando; Heaney, Jim

1998-01-01

The Composite Infrared Spectrometer (CIRS) instrument on the Cassini Mission launched in October of 1997. The CIRS instrument contains a mid-infrared and a far-infrared interferometer and operates at 170 Kelvin. The mid-infrared interferometer is a Michelson- type Fourier transform spectrometer utilizing a 3 inch diameter potassium bromide beamsplitter/compensator pair. The potassium bromide elements were tested to verify effects of cooldown and vibration prior to integration into the instrument. The instrument was then aligned at ambient temperatures, tested cryogenically and re-verified after vibration. The stringent design optical figure requirements for the beamsplitter and compensator included fabrication errors, mounting stresses and vibration load effects. This paper describes the challenges encountered in mounting the elements to minimize distortion and to survive vibration.

Current Pyridostigmine Bromide and Huperzine A Studies and Future Cholinesterase Screening Using the WRAIR Whole Blood Cholinesterase Assay

DTIC Science & Technology

2004-11-15

1 CURRENT PYRIDOSTIGMINE BROMIDE AND HUPERZINE A STUDIES AND FUTURE CHOLINESTERASE SCREENING USING THE WRAIR WHOLE BLOOD...selective (e.g. Huperzine A ) and non-selective (carbamate) inhibitors (e.g. pyridostigmine bromide, PB). We found that volunteers given pyridostigmine...profile of healthy elderly volunteers receiving Huperzine A . 52.7 ± 1.5% inhibition was observed at the end of an increasing dose regimen (final dose

Trends in bromide wet deposition concentrations in the contiguous United States, 2001-2016.

PubMed

Wetherbee, Gregory A; Lehmann, Christopher M B; Kerschner, Brian M; Ludtke, Amy S; Green, Lee A; Rhodes, Mark F

2018-02-01

Bromide (Br - ) and other solute concentration data from wet deposition samples collected and analyzed by the National Atmospheric Deposition Program (NADP) from 2001 to 2016, were statistically analyzed for trends both geographically and temporally by precipitation type. Analysis was limited to NADP sites in the contiguous 48 United States. The Br - concentrations for this time period had a high number of values censored at the detection limits with greater than 86 percent of sample concentrations below analytical detection. Bromide was more frequently detected at NADP sites in coastal regions. Analysis using specialized statistical techniques for censored data revealed that Br - concentrations varied by precipitation type with higher concentrations usually observed in liquid versus precipitation containing snow. Negative temporal trends in Br - wet deposition concentrations were observed at a majority of NADP sites; approximately 25 percent of these trend values were statistically significant at less than 0.05 to 0.10 significance levels. Potential causes for the negative trends were explored, including annual and seasonal changes in precipitation depth, reduced emissions of methyl bromide (CH 3 Br) from coastal wetlands, and declining industrial use of bromine compounds. The results indicate that Br - in non-coastal wet-deposition comes mainly from long-range transport, not local sources. Correlations between Br - , chloride, and nitrate concentrations also were evaluated. Published by Elsevier Ltd.

Pyridostimine Bromide 30mg Stability in Extended Storage Conditions

DTIC Science & Technology

2017-12-03

limit 100 words): Pyridostigmine bromide 30mg is approved by the Federal Drug Administration (FDA) as a pre -treatment of nerve gas exposure. The...under controlled temperatu,re and humidity. The tablets will be tested at 0, 3, 4, 5, and 6 months after removal from refrigerator when stored at both...Guidance definitions of storage conditions required for stability testing to obtain new drug approval in different climate zones in the world. At

Mechanism of HERG potassium channel inhibition by tetra-n-octylammonium bromide and benzethonium chloride

DOE Office of Scientific and Technical Information (OSTI.GOV)

Long, Yan; Lin, Zuoxian; Xia, Menghang

Tetra-n-octylammonium bromide and benzethonium chloride are synthetic quaternary ammonium salts that are widely used in hospitals and industries for the disinfection and surface treatment and as the preservative agent. Recently, the activities of HERG channel inhibition by these compounds have been found to have potential risks to induce the long QT syndrome and cardiac arrhythmia, although the mechanism of action is still elusive. This study was conducted to investigate the mechanism of HERG channel inhibition by these compounds by using whole-cell patch clamp experiments in a CHO cell line stably expressing HERG channels. Tetra-n-octylammonium bromide and benzethonium chloride exhibited concentration-dependentmore » inhibitions of HERG channel currents with IC{sub 50} values of 4 nM and 17 nM, respectively, which were also voltage-dependent and use-dependent. Both compounds shifted the channel activation I–V curves in a hyperpolarized direction for 10–15 mV and accelerated channel activation and inactivation processes by 2-fold. In addition, tetra-n-octylammonium bromide shifted the inactivation I–V curve in a hyperpolarized direction for 24.4 mV and slowed the rate of channel deactivation by 2-fold, whereas benzethonium chloride did not. The results indicate that tetra-n-octylammonium bromide and benzethonium chloride are open-channel blockers that inhibit HERG channels in the voltage-dependent, use-dependent and state-dependent manners. - Highlights: ► Tetra-n-octylammonium and benzethonium are potent HERG channel inhibitors. ► Channel activation and inactivation processes are accelerated by the two compounds. ► Both compounds are the open-channel blockers to HERG channels. ► HERG channel inhibition by both compounds is use-, voltage- and state dependent. ► The in vivo risk of QT prolongation needs to be studied for the two compounds.« less

Impact of bromide on halogen incorporation into organic moieties in chlorinated drinking water treatment and distribution systems.

PubMed

Tan, J; Allard, S; Gruchlik, Y; McDonald, S; Joll, C A; Heitz, A

2016-01-15

The impact of elevated bromide concentrations (399 to 750 μg/L) on the formation of halogenated disinfection by-products (DBPs), namely trihalomethanes, haloacetic acids, haloacetonitriles, and adsorbable organic halogen (AOX), in two drinking water systems was investigated. Bromine was the main halogen incorporated into all of the DBP classes and into organic carbon, even though chlorine was present in large excess to maintain a disinfectant residual. Due to the higher reactivity of bromine compared to chlorine, brominated DBPs were rapidly formed, followed by a slower increase in chlorinated DBPs. Higher bromine substitution and incorporation factors for individual DBP classes were observed for the chlorinated water from the groundwater source (lower concentration of dissolved organic carbon (DOC)), which contained a higher concentration of bromide, than for the surface water source (higher DOC). The molar distribution of adsorbable organic bromine to chlorine (AOBr/AOCl) for AOX in the groundwater distribution system was 1.5:1 and almost 1:1 for the surface water system. The measured (regulated) DBPs only accounted for 16 to 33% of the total organic halogen, demonstrating that AOX measurements are essential to provide a full understanding of the formation of halogenated DBPs in drinking waters. In addition, the study demonstrated that a significant proportion (up to 94%) of the bromide in source waters can be converted AOBr. An evaluation of AOBr and AOCl through a second groundwater treatment plant that uses conventional treatment processes for DOC removal produced 70% of AOX as AOBr, with 69% of the initial source water bromide converted to AOBr. Exposure to organobromine compounds is suspected to result in greater adverse health consequences than their chlorinated analogues. Therefore, this study highlights the need for improved methods to selectively reduce the bromide content in source waters. Copyright © 2015 Elsevier B.V. All rights reserved.

Sodium bromide additive improved film morphology and performance in perovskite light-emitting diodes

NASA Astrophysics Data System (ADS)

Li, Jinghai; Cai, Feilong; Yang, Liyan; Ye, Fanghao; Zhang, Jinghui; Gurney, Robert S.; Liu, Dan; Wang, Tao

2017-07-01

Organometal halide perovskite is a promising material to fabricate light-emitting diodes (LEDs) via solution processing due to its exceptional optoelectronic properties. However, incomplete precursor conversion and various defect states in the perovskite light-emitting layer lead to low luminance and external quantum efficiency of perovskite LEDs. We show here the addition of an optimum amount of sodium bromide in the methylammonium lead bromide (MAPbBr3) precursor during a one-step perovskite solution casting process can effectively improve the film coverage, enhance the crystallinity, and passivate ionic defects on the surface of MAPbBr3 crystal grains, resulting in LEDs with a reduced turn-on voltage from 2.8 to 2.3 V and an enhanced maximum luminance from 1059 to 6942 Cd/m2 when comparing with the pristine perovskite-based device.

Interaction of ozone and carbon dioxide with polycrystalline potassium bromide and its atmospheric implication

NASA Astrophysics Data System (ADS)

Levanov, Alexander V.; Isaikina, Oksana Ya.; Maksimov, Ivan B.; Lunin, Valerii V.

2017-03-01

It has been discovered for the first time that gaseous ozone in the presence of carbon dioxide and water vapor interacts with crystalline potassium bromide giving gaseous Br2 and solid salts KHCO3 and KBrO3. Molecular bromine and hydrocarbonate ion are the products of one and the same reaction described by the stoichiometric equation 2KBr(cr.) + O3(gas) + 2CO2(gas) + H2O(gas) → 2KHCO3(cr.) + Br2(gas) + O2(gas). The dependencies of Br2, KHCO3 and KBrO3 formation rates on the concentrations of O3 and CO2, humidity of initial gas mixture, and temperature have been investigated. A kinetic scheme has been proposed that explains the experimental regularities found in this work on the quantitative level. According to the scheme, the formation of molecular bromine and hydrocarbonate is due to the reaction between hypobromite BrO-, the primary product of bromide oxidation by ozone, with carbon dioxide and water; bromate results from consecutive oxidation of bromide ion by ozone Br- → +O3 , -O2 BrO- → +O3 , -O2 BrO2- → +O3, -O2 BrO3- .

A case report of QT prolongation with glycopyrronium bromide in a patient with chronic tamoxifen use.

PubMed

Chiu, Michael H; Al-Majed, Nawaf S; Stubbins, Ryan; Pollmann, Dylan; Sandhu, Roopinder K

2016-06-14

Glycopyrronium bromide has recently been approved as a once daily maintenance inhalation therapy for moderate to severe chronic obstructive pulmonary disease (COPD). Efficacy and safety trial data have found rare cases of significant QT prolongation. To our knowledge, we describe the first case report of QT prolongation >600 ms with initiation of glycopyrronium bromide in a real world setting. A 78-year-old female with moderate COPD recently started on glycopyrronium bromide, presented to Emergency Department (ED) with syncope. Her past medical history was significant for a left total mastectomy and she had been on Tamoxifen for 9 months. One day prior to her presentation, she had visited a naturopathic clinic for a vitamin infusion resulting in emesis. The following day she continued to feel dizzy and had a witnessed syncopal episode without any reported cardiac or neurological symptoms preceding the event or after regaining consciousness. In the emergency department, she reported dizziness and was found to be hypotensive. Her symptoms completely resolved with intravenous fluids. Lab work was normal however her electrocardiogram (ECG) demonstrated a QTc interval of 603 and 631 ms (Friderica and Bazett's respectively) with a normal QT interval on her baseline ECG prior to initiating Tamoxifen. She was admitted to the Cardiology service for further work-up of QT prolongation. Her syncope was felt to be due to orthostatic hypotension and the QT prolongation secondary to medications, which were both discontinued during her admission. After 2 days, her QT interval normalized consistent with the half-life of Glycopyrronium bromide (13-57 h) compared to Tamoxifen (8-14 days). Glycopyrronium bromide is guideline recommended as first line therapy for prevention of exacerbation in moderate to severe COPD however safety data had been limited to select populations. This case report highlights the need for future studies to identify high-risk populations at potential

Determination of bromide in aqueous solutions via the TlBr molecule using high-resolution continuum source graphite furnace molecular absorption spectrometry

NASA Astrophysics Data System (ADS)

Cacho, Frantisek; Machynak, Lubomir; Nemecek, Martin; Beinrohr, Ernest

2018-06-01

The paper describes the determination of bromide by evaluating the molecular absorption of thallium mono-bromide (TlBr) at the rotational line at 342.9815 nm by making use a high-resolution continuum source graphite furnace atomic absorption spectrometer. The effects of variables such as the wavelength, graphite furnace program, amount of Tl and the use of a modifier were investigated and optimized. Various chemical modifiers have been studied, such as Pd, Mg, Ag and a mixture of Pd/Mg. It was found that best results were obtained by using Ag which prevents losses of bromide during pyrolysis step through precipitation of bromide as AgBr. In this way, a maximum pyrolysis temperature of 400 °C could be used. The optimum molecule forming temperature was found to be 900 °C. Bromide concentrations in various water samples (CRM, bottled drinking water and tap water) were determined. The quantification was made by both linear calibration and standard addition techniques. The results were matched well those of the reference method. The calibration curve was linear in the range between 1 and 1000 ng Br with a correlation coefficient R = 0.999. The limit of detection and characteristic mass of the method were 0.3 ng and 4.4 ng of Br.

Replacing Conventional Carbon Nucleophiles with Electrophiles: Nickel-Catalyzed Reductive Alkylation of Aryl Bromides and Chlorides

PubMed Central

2012-01-01

A general method is presented for the synthesis of alkylated arenes by the chemoselective combination of two electrophilic carbons. Under the optimized conditions, a variety of aryl and vinyl bromides are reductively coupled with alkyl bromides in high yields. Under similar conditions, activated aryl chlorides can also be coupled with bromoalkanes. The protocols are highly functional-group tolerant (−OH, −NHTs, −OAc, −OTs, −OTf, −COMe, −NHBoc, −NHCbz, −CN, −SO2Me), and the reactions are assembled on the benchtop with no special precautions to exclude air or moisture. The reaction displays different chemoselectivity than conventional cross-coupling reactions, such as the Suzuki–Miyaura, Stille, and Hiyama–Denmark reactions. Substrates bearing both an electrophilic and nucleophilic carbon result in selective coupling at the electrophilic carbon (R–X) and no reaction at the nucleophilic carbon (R–[M]) for organoboron (−Bpin), organotin (−SnMe3), and organosilicon (−SiMe2OH) containing organic halides (X–R–[M]). A Hammett study showed a linear correlation of σ and σ(−) parameters with the relative rate of reaction of substituted aryl bromides with bromoalkanes. The small ρ values for these correlations (1.2–1.7) indicate that oxidative addition of the bromoarene is not the turnover-frequency determining step. The rate of reaction has a positive dependence on the concentration of alkyl bromide and catalyst, no dependence upon the amount of zinc (reducing agent), and an inverse dependence upon aryl halide concentration. These results and studies with an organic reductant (TDAE) argue against the intermediacy of organozinc reagents. PMID:22463689

40 CFR 721.4090 - Ethanaminium, N-[bis(diethylamino)-methylene]-N-ethyl-, bromide.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Ethanaminium, N-[bis(diethylamino)-methylene]-N-ethyl-, bromide. 721.4090 Section 721.4090 Protection of Environment ENVIRONMENTAL PROTECTION... New Uses for Specific Chemical Substances § 721.4090 Ethanaminium, N-[bis(diethylamino)-methylene]-N...

40 CFR 721.4090 - Ethanaminium, N-[bis(diethylamino)-methylene]-N-ethyl-, bromide.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Ethanaminium, N-[bis(diethylamino)-methylene]-N-ethyl-, bromide. 721.4090 Section 721.4090 Protection of Environment ENVIRONMENTAL PROTECTION... New Uses for Specific Chemical Substances § 721.4090 Ethanaminium, N-[bis(diethylamino)-methylene]-N...

Palladium-Catalyzed Conversion of Aryl and Vinyl Triflates to Bromides and Chlorides

PubMed Central

Shen, Xiaoqiang; Hyde, Alan M.; Buchwald, Stephen L.

2010-01-01

The palladium-catalyzed conversion of aryl and vinyl triflates to aryl and vinyl halides (bromides and chlorides) has been developed using dialkylbiaryl phosphine ligands. A variety of aryl, heteroaryl and vinyl halides can be prepared via this method in good to excellent yields. PMID:20857936

Granular Activated Carbon Treatment May Result in Higher Predicted Genotoxicity in the Presence of Bromide.

PubMed

Krasner, Stuart W; Lee, Tiffany Chih Fen; Westerhoff, Paul; Fischer, Natalia; Hanigan, David; Karanfil, Tanju; Beita-Sandí, Wilson; Taylor-Edmonds, Liz; Andrews, Robert C

2016-09-06

Certain unregulated disinfection byproducts (DBPs) are more of a health concern than regulated DBPs. Brominated species are typically more cytotoxic and genotoxic than their chlorinated analogs. The impact of granular activated carbon (GAC) on controlling the formation of regulated and selected unregulated DBPs following chlorine disinfection was evaluated. The predicted cyto- and genotoxicity of DBPs was calculated using published potencies based on the comet assay for Chinese hamster ovary cells (assesses the level of DNA strand breaks). Additionally, genotoxicity was measured using the SOS-Chromotest (detects DNA-damaging agents). The class sum concentrations of trihalomethanes, haloacetic acids, and unregulated DBPs, and the SOS genotoxicity followed the breakthrough of dissolved organic carbon (DOC), however the formation of brominated species did not. The bromide/DOC ratio was higher than the influent through much of the breakthrough curve (GAC does not remove bromide), which resulted in elevated brominated DBP concentrations in the effluent. Based on the potency of the haloacetonitriles and halonitromethanes, these nitrogen-containing DBPs were the driving agents of the predicted genotoxicity. GAC treatment of drinking or reclaimed waters with appreciable levels of bromide and dissolved organic nitrogen may not control the formation of unregulated DBPs with higher genotoxicity potencies.

Use of normal propyl bromide solvents for extraction and recovery of asphalt cements

DOT National Transportation Integrated Search

2000-11-01

Four normal propyl bromide (nPB) solvents were evaluated for use as chlorinated solvent replacements in typical hot mix asphalt (HMA) extraction and recovery processes. The experimental design included one method of extraction (centrifuge), one metho...

Room temperature synthesis of silver nanowires from tabular silver bromide crystals in the presence of gelatin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu Suwen; Wehmschulte, Rudolf J.; Lian Guoda

2006-03-15

Long silver nanowires were synthesized at room temperature by a simple and fast process derived from the development of photographic films. A film consisting of an emulsion of tabular silver bromide grains in gelatin was treated with a photographic developer (4-(methylamino)phenol sulfate (metol), citric acid) in the presence of additional aqueous silver nitrate. The silver nanowires have lengths of more than 50 {mu}m, some even more than 100 {mu}m, and average diameters of about 80 nm. Approximately, 70% of the metallic silver formed in the reduction consists of silver nanowires. Selected area electron diffraction (SAED) results indicate that the silvermore » nanowires grow along the [111] direction. It was found that the presence of gelatin, tabular silver bromide crystals and silver ions in solution are essential for the formation of the silver nanowires. The nanowires appear to originate from the edges of the silver bromide crystals. They were characterized by transmission electron microscopy (TEM), SAED, scanning electron microscopy (SEM), and powder X-ray diffraction (XRD)« less

Room temperature synthesis of silver nanowires from tabular silver bromide crystals in the presence of gelatin

NASA Astrophysics Data System (ADS)

Liu, Suwen; Wehmschulte, Rudolf J.; Lian, Guoda; Burba, Christopher M.

2006-03-01

Long silver nanowires were synthesized at room temperature by a simple and fast process derived from the development of photographic films. A film consisting of an emulsion of tabular silver bromide grains in gelatin was treated with a photographic developer (4-(methylamino)phenol sulfate (metol), citric acid) in the presence of additional aqueous silver nitrate. The silver nanowires have lengths of more than 50 μm, some even more than 100 μm, and average diameters of about 80 nm. Approximately, 70% of the metallic silver formed in the reduction consists of silver nanowires. Selected area electron diffraction (SAED) results indicate that the silver nanowires grow along the [111] direction. It was found that the presence of gelatin, tabular silver bromide crystals and silver ions in solution are essential for the formation of the silver nanowires. The nanowires appear to originate from the edges of the silver bromide crystals. They were characterized by transmission electron microscopy (TEM), SAED, scanning electron microscopy (SEM), and powder X-ray diffraction (XRD).

United States Department of Agriculture-Agricultural Research Service research on alternatives to methyl bromide: pre-plant and post-harvest.

PubMed

Schneider, Sally M; Rosskopf, Erin N; Leesch, James G; Chellemi, Daniel O; Bull, Carolee T; Mazzola, Mark

2003-01-01

Methyl bromide is a widely used fumigant for both pre-plant and post-harvest pest and pathogen control. The Montreal Protocol and the US Clean Air Act mandate a phase-out of the import and manufacture of methyl bromide, beginning in 2001 and culminating with a complete ban, except for quarantine and certain pre-shipment uses and exempted critical uses, in January 2005. In 1995, ARS built on its existing programs in soil-borne plant pathology and post-harvest entomology and plant pathology to initiate a national research program to develop alternatives to methyl bromide. The focus has been on strawberry, pepper, tomato, perennial and nursery cropping systems for pre-plant methyl bromide use and fresh and durable commodities for post-harvest use. Recently the program has been expanded to include research on alternatives for the ornamental and cut flower cropping systems. An overview of the national research program is presented. Results from four specific research trials are presented, ranging from organic to conventional systems. Good progress on short-term alternatives is being made. These will be used as the foundation of integrated management systems which begin with pre-plant management decisions and continue through post-harvest processing.

Thallium Bromide Deposited Using Spray Coating

NASA Astrophysics Data System (ADS)

Ferreira, E. S.; Mulato, M.

2012-08-01

Spray coating was used to produce thallium bromide samples on glass substrates. The influence of several fabrication parameters on the final structural properties of the samples was investigated. Substrate position, substrate temperature, solution concentration, carrying gas, and solution flow were varied systematically, the physical deposition mechanism involved in each case being discussed. Total deposition time of about 3.5 h can lead to 62-μm-thick films, comprising completely packed micrometer-sized crystalline grains. X-ray diffraction and scanning electron microscopy were used to characterize the samples. On the basis of the experimental data, the optimum fabrication conditions were identified. The technique offers an alternative method for fast, cheap fabrication of large-area devices for the detection of high-energy radiation, i.e., X-rays and γ-rays, in medical imaging.

Steam disinfestation as a methyl bromide alternative in California cut flower nurseries

USDA-ARS?s Scientific Manuscript database

Steam may be an effective alternative to methyl bromide in cut flower production in California. Advantages of steam include broad spectrum pest control and a zero hour re-entry interval. The principle disadvantage of sheet steaming is cost effectiveness due to current energy prices and application...

Hydrology and Water Quality near Bromide Pavilion in Chickasaw National Recreation Area, Murray County, Oklahoma, 2000

USGS Publications Warehouse

Andrews, William J.; Burrough, Steven P.

2002-01-01

The Bromide Pavilion in Chickasaw National Recreation Area drew many thousands of people annually to drink the mineral-rich waters piped from nearby Bromide and Medicine Springs. Periodic detection of fecal coliform bacteria in water piped to the pavilion from the springs, low yields of the springs, or flooding by adjacent Rock Creek prompted National Park Service officials to discontinue piping of the springs to the pavilion in the 1970s. Park officials would like to resume piping mineralized spring water to the pavilion to restore it as a visitor attraction, but they are concerned about the ability of the springs to provide sufficient quantities of potable water. Pumping and sampling of Bromide and Medicine Springs and Rock Creek six times during 2000 indicate that these springs may not provide sufficient water for Bromide Pavilion to supply large numbers of visitors. A potential problem with piping water from Medicine Spring is the presence of an undercut, overhanging cliff composed of conglomerate, which may collapse. Evidence of intermittent inundation of the springs by Rock Creek and seepage of surface water into the spring vaults from the adjoining creek pose a threat of contamination of the springs. Escherichia coli, fecal coliform, and fecal streptococcal bacteria were detected in some samples from the springs, indicating possible fecal contamination. Cysts of Giardia lamblia and oocysts of Cryptosporidium parvum protozoa were not detected in the creek or the springs. Total culturable enteric viruses were detected in only one water sample taken from Rock Creek.

Preparation and optical characteristics of layered perovskite-type lead-bromide-incorporated azobenzene chromophores

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sasai, Ryo, E-mail: rsasai@riko.shimane-u.ac.jp; Shinomura, Hisashi

Lead bromide-based layered perovskite powders with azobenzene derivatives were prepared by a homogeneous precipitation method. From the diffuse reflectance (DR) and photoluminescence (PL) spectra of the hybrid powder materials, the present hybrids exhibited sharp absorption and PL peaks originating from excitons produced in the PbBr{sub 4}{sup 2-} layer. When the present hybrid powder was irradiated with UV light at 350 nm, the absorption band from the trans-azobenzene chromophore, observed around 350 nm, decreased, while the absorption band from the cis-azobenzene chromophore, observed around 450 nm, increased. These results indicate that azobenzene chromophores in the present hybrid materials exhibit reversible photoisomerization.more » Moreover, it was found that the PL intensity from the exciton also varied due to photoisomerization of the azobenzene chromophores in the present hybrid. Thus, for the first time we succeeded in preparing the azobenzene derivative lead-bromide-based layered perovskite with photochromism before and after UV light irradiation. - Graphical abstract: For the first time, we succeeded in preparing the azobenzene derivative lead-bromide-based layered perovskite with photochromism before and after UV light irradiation. Highlights: Black-Right-Pointing-Pointer PbBr-based layered perovskite with azobenezene derivatives could be synthesized by a homogeneous precipitation method. Black-Right-Pointing-Pointer Azobenzene derivatives incorporated the present hybrid that exhibited reversible photoisomerization under UV and/or visible light irradiation. Black-Right-Pointing-Pointer PL property of the present hybrid could also be varied by photoisomerization.« less

Eradicating European pine shoot moth on ornamental pines with methyl bromide.

Treesearch

V.M. Carolin; W.H. Klein; R.M. Thompson

1962-01-01

The recent introduction of the European pine shoot moth into this region poses a serious threat to natural pine stands. To combat this threat, quarantines were invoked and eradication programs undertaken. Destruction of infested trees has been used tentatively as an eradication technique. In the meantime, fumigation with methyl bromide was tested over the period of a...

Vibrational and reorientationl relaxation in liquid tert-butyl bromide and tert-butyl bromide- d9

NASA Astrophysics Data System (ADS)

Szostak, R.; Hawranek, J. P.

1992-12-01

The vibrational and reorientational correlation functions of the ν s(CBr) mode in liquid tert-butyl bromide (TBBr) and in its deuterated analogue (TBBr- d9) were determined from Raman bandshapes. The Kubo product δτ m obtained by fitting the Rothschild equation to experimental data amounts to 0.36-0.45 for the studied bands, which indicates a fairly fast modulation regime in these systems. The approximation of experimental rotational correlation functions with the help of the J-diffusion model yields values of 0.11-0.12ps for the angular momentum correlation time. The second-order rotational correlation times (1.7-2.0ps) agree well with the NMR results of D.W. Aksnes, K. Ramstad and O.P. Björlykke, Magn. Reson. Chem., 25 (1987) 1063. Selected bandshape parameters for δ(CCC) in both compounds, ϱ(CH 3) in TBBr and ν s(CC) in TBBR- d9 were also quoted.

Single ion dynamics in molten sodium bromide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alcaraz, O.; Trullas, J.; Demmel, F.

We present a study on the single ion dynamics in the molten alkali halide NaBr. Quasielastic neutron scattering was employed to extract the self-diffusion coefficient of the sodium ions at three temperatures. Molecular dynamics simulations using rigid and polarizable ion models have been performed in parallel to extract the sodium and bromide single dynamics and ionic conductivities. Two methods have been employed to derive the ion diffusion, calculating the mean squared displacements and the velocity autocorrelation functions, as well as analysing the increase of the line widths of the self-dynamic structure factors. The sodium diffusion coefficients show a remarkable goodmore » agreement between experiment and simulation utilising the polarisable potential.« less

Methyl bromide release from activated carbon and the soil/water/carbon interface

USDA-ARS?s Scientific Manuscript database

Methyl Bromide (MB) is a major source of stratospheric bromine radical, a known depletor of ozone. The use of ozone-depleting chemicals, including MB, is regulated by the Montreal Protocol. Critical uses of MB are permitted, such as when postharvest fumigation is mandated by an importing country. Fo...

EVALUATION OF CONTAINMENT AND CONTROL OPTIONS FOR METHYL BROMIDE IN COMMODITY TREATMENT

EPA Science Inventory

The report gives results of an investigation of means for methyl bromide (MeBr) recovery, reuse, and destruction to prevent atmospheric emissions if its limited use were still allowed. (NOTE: MeBr is an ozone-depleting chemical scheduled to be phased out by the Clean Air Act by t...

Simultaneous removal of dissolved organic matter and bromide from drinking water source by anion exchange resins for controlling disinfection by-products.

PubMed

Phetrak, Athit; Lohwacharin, Jenyuk; Sakai, Hiroshi; Murakami, Michio; Oguma, Kumiko; Takizawa, Satoshi

2014-06-01

Anion exchange resins (AERs) with different properties were evaluated for their ability to remove dissolved organic matter (DOM) and bromide, and to reduce disinfection by-product (DBP) formation potentials of water collected from a eutrophic surface water source in Japan. DOM and bromide were simultaneously removed by all selected AERs in batch adsorption experiments. A polyacrylic magnetic ion exchange resin (MIEX®) showed faster dissolved organic carbon (DOC) removal than other AERs because it had the smallest resin bead size. Aromatic DOM fractions with molecular weight larger than 1600 Da and fluorescent organic fractions of fulvic acid- and humic acid-like compounds were efficiently removed by all AERs. Polystyrene AERs were more effective in bromide removal than polyacrylic AERs. This result implied that the properties of AERs, i.e. material and resin size, influenced not only DOM removal but also bromide removal efficiency. MIEX® showed significant chlorinated DBP removal because it had the highest DOC removal within 30 min, whereas polystyrene AERs efficiently removed brominated DBPs, especially brominated trihalomethane species. The results suggested that, depending on source water DOM and bromide concentration, selecting a suitable AER is a key factor in effective control of chlorinated and brominated DBPs in drinking water. Copyright © 2014 The Research Centre for Eco-Environmental Sciences, Chinese Academy of Sciences. Published by Elsevier B.V. All rights reserved.

Ice Wedge Polygon Bromide Tracer Experiment in Subsurface Flow, Barrow, Alaska, 2015-2016

DOE Data Explorer

Nathan Wales

2018-02-15

Time series of bromide tracer concentrations at several points within a low-centered polygon and a high-centered polygon. Concentration values were obtained from the analysis of water samples via ion chromatography with an accuracy of 0.01 mg/l.

The speciation of aqueous zinc(II) bromide solutions to 500 °C and 900 MPa determined using Raman spectroscopy

USGS Publications Warehouse

Mibe, Kenji; Chou, I-Ming; Anderson, Alan J.; Mayanovic, Robert A.; Bassett, William A.

2009-01-01

A Raman spectral study was carried out on 3 solutions of varying concentration and bromide/zinc ratios. Spectra were collected at 11 different temperature-pressure conditions ranging from ambient to 500????C-0.9??GPa. Raman band assignments for zinc(II) bromide species reported in previous studies were used to determine the relative concentrations of ZnBr42-, ZnBr3-, ZnBr2, and ZnBr+ species at various temperatures and pressures. Our results are in close agreement with X-ray absorption spectroscopic (XAS) data, and confirm that the tetrabromo zinc(II) complex, ZnBr42-, is the predominant species up to 500????C in solutions having high Zn concentrations (1??m) and high bromide/zinc molar ratios ([Br]/[Zn] = 8). In agreement with previous solubility and Raman spectroscopic experiments, our measurements indicate that species with a lower number of halide ligands and charge are favored with increasing temperature in dilute solutions, and solutions with low bromide/zinc ratios ([Br]/[Zn] < 2.5). The Raman technique provides an independent experimental means of evaluating the quality of XAS analyses of data obtained from high temperature disordered systems. The combination of these two techniques provides complementary data on speciation and the structure of zinc(II) bromide complexes. The preponderance of the ZnBr42- species in highly saline brines at high temperature is consistent with the predominance of ZnCl42- in chloride-rich brines reported in previous XAS studies. Knowledge of Zn complexing in metal-rich highly saline brines is important for numerical models of ore deposition in high temperature systems such as skarns and porphyry-type deposits. ?? 2008 Elsevier B.V.

Bromate formation from the oxidation of bromide in the UV/chlorine process with low pressure and medium pressure UV lamps.

PubMed

Fang, Jingyun; Zhao, Quan; Fan, Chihhao; Shang, Chii; Fu, Yun; Zhang, Xiangru

2017-09-01

When a bromide-containing water is treated by the ultraviolet (UV)/chlorine process, hydroxyl radicals (HO) and halogen radicals such as Cl or Br are formed due to the UV photolysis of free halogens. These reactive species may induce the formation of bromate, which is a probable human carcinogen. Bromate formation in the UV/chlorine process using low pressure (LP) and medium pressure (MP) lamps in the presence of bromide was investigated in the present study. The UV/chlorine process significantly enhanced bromate formation as compared to dark chlorination. The bromate formation was elevated with increasing UV fluence, bromide concentration, and pH values under both LP and MP UV irradiations. It was significantly enhanced at pH 9 compared to those at pH 6 and 7 with MP UV irradiation, while it was slightly enhanced at pH 9 with LP UV. The formation by UV/chlorine process started with the formation of free bromine (HOBr/OBr - ) through the reaction of chlorine and bromide, followed by a subsequent oxidation of free bromine and formation of BrO and bromate by reacting with radicals. Copyright © 2017 Elsevier Ltd. All rights reserved.

Evaluation of bromide mass discharge in a sandy aquifer at Vandenberg AFB, CA

NASA Astrophysics Data System (ADS)

Mackay, D. M.; Rasa, E.; Einarson, M.; Kaiser, P.; Chakraborty, I.; Scow, K. M.

2009-12-01

Side-by-side experiments were conducted by UC Davis research team at a former fuel station at Vandenberg Air Force Base (AFB) to evaluate the rate of transformation of methyl tert-butyl ether (MTBE) to tert-butyl alcohol (TBA) impacted by ethanol and to investigate evidence of TBA degradation under sulfate reducing conditions. On one side we injected groundwater amended with ethanol and MTBE. In the other lane we injected groundwater amended with TBA. On both sides, injected ground water was spiked with bromide tracer to provide estimates of groundwater flow direction variations, flow velocity, dispersion, and mobile mass loss resulting from diffusive sequestration into aquitards. 162 monitoring wells were aligned into seven transects located downgradient of the injection wells. The mass discharge approach was used to evaluate the natural attenuation of the injected constituents. In this talk we will focus on calculations of mass discharge of the bromide tracer at each of the seven monitoring well transects. The amount of bromide mass discharged through each transect was calculated for any sampling time using field measurements of break through curves. Cumulative mass discharges were estimated and, by iteration based on mass balance, the flow properties of the aquifer were estimated. The calibration process resulted in subtle but quantitatively important changes in our assumptions regarding key physical properties of the aquifer (thickness, porosity) which could be only approximately estimated by standard methods (coring, CPT, etc.). On the basis of this calibration, a more robust approach was devised for evaluating the source and fate of TBA in the aquifer.

On the stereochemical course of palladium-catalyzed cross-coupling of allylic silanolate salts with aromatic bromides.

PubMed

Denmark, Scott E; Werner, Nathan S

2010-03-17

The stereochemical course of palladium-catalyzed cross-coupling reactions of an enantioenriched, alpha-substituted, allylic silanolate salt with aromatic bromides has been investigated. The allylic silanolate salt was prepared in high geometrical (Z/E, 94:6) and high enantiomeric (94:6 er) purity by a copper-catalyzed S(N)2' reaction of a resolved allylic carbamate. Eight different aromatic bromides underwent cross-coupling with excellent constitutional site-selectivity and excellent stereospecificity. Stereochemical correlation established that the transmetalation event proceeds through a syn S(E)' mechanism which is interpreted in terms of an intramolecular delivery of the arylpalladium electrophile through a key intermediate that contains a discrete Si-O-Pd linkage.

Ninety-Day Subchronic Oral Toxicity Study of Pyridostigmine Bromide in Rats. Volume 1

DTIC Science & Technology

1990-05-01

myasthenia gravis because of its relative lack of untoward effects in comparison with other anticholinesterases (2). This relative lack of clinical...treatment of myasthenia gravis . Objecrive of Study The objective of this study was to determine the 90-day subchronic toxicity of pyridostigmine bromide in

Potassium bromide, KBr/ ε: New Force Field

NASA Astrophysics Data System (ADS)

Fuentes-Azcatl, Raúl; Barbosa, Marcia C.

2018-02-01

We propose a new force field for the Potassium Bromide, the KBr/ ε. The crystal density and structure, as well as, the density, the viscosity and the dielectric constant of the solution in water were computed and compared with the experiments and other atomistic models. Next, the transferability of the KBr/ ε and of the NaCl/ ε models is verified by creating the KCl/ ε and the NaBr/ ε models. The strategy was to employ the same parameters obtained for the NaCl/ ε and for the KBr/ ε force fields for the building up of the KCl/ ε and the NaBr/ ε models . The thermodynamic and dynamic properties of these two new models were compared with the experimental

Neuropsychological Functioning in Gulf War Veterans Exposed to Pesticides and Pyridostigmine Bromide

DTIC Science & Technology

2008-02-01

processing speed and mood and sequelae from overt poisoning from organophosphate pesticides can result in lasting deficits in the domains of visuomotor...R. G., O’Malley, M., Chrislip, D., & Russo, J. (1994). Chronic neurological sequelae to organophosphate pesticide poisoning . American...War Veterans Exposed to Pesticides and Pyridostigmine Bromide PRINCIPAL INVESTIGATOR: Maxine Krengel, Ph.D

Mononuclear bromide complexes of Sb(V): crystal structures and thermal behaviour

NASA Astrophysics Data System (ADS)

Adonin, Sergey A.; Bondarenko, Mikhail A.; Samsonenko, Denis G.; Semitut, Evgeniy Yu; Sokolov, Maxim N.; Fedin, Vladimir P.

2018-05-01

Reactions of Sb2O3 dissolved in HBr/Br2 and bromides of pyridinium-derived cations result in mononuclear complexes of Sb(V) - (cation)[SbBr6] (cation = 2-chloropyridinium (1), 2-bromopyridinium (2)). Thermal behaviour of 1 and 2, as well as similar previously reported complexes Et4N [SbBr6] (3) and (N-EtPy)[SbBr6] (4), was studied and discussed.

Interaction of pyridostigmine bromide and N,N-diethyl-m-toluamide alone and in combination with P-glycoprotein expressed in Escherichia coli leaky mutant.

PubMed

El-Masry, Eman M; Abou-Donia, Mohamed B

2006-05-01

P-glycoprotein (P-gp), the most extensively studied ATP-binding transporter, functions as a biological barrier by extruding toxic substances and xenobiotics out of the cell. This study was carried out to determine the effect of N,N-diethyl-m-toluamide (DEET) and pyridostigmine bromide (PB), alone and in combination, on P-gp expression using Escherichia coli leaky mutant transformed with Mdr1 gene (pT5-7/mdr1), which codes for P-gp or lactose permease (pT5-7/lacY) as negative control. Also, daunomycin (a known P-gp sustrate) was used as a positive control and reserpine (a known P-gp inhibitor) served as a negative control. An in vitro cell-resistant assay was used to monitor the potential of test compounds to interact with P-gp. Following exposure of the cells to pyridostigmine bromide or daunomycin, P-gp conferred significant resistance against both compounds, while reserpine and DEET significantly inhibited the glycoprotein. Cells were grown in the presence of noncytotoxic concentrations of daunomycin, pyridostigmine bromide, reserpine, or DEET, and membrane fractions were examined by Western immunoblotting for expression of P-gp. Daunomycin induced P-gp expression quantitatively more than pyridostigmine bromide, while reserpine and DEET significantly inhibited P-gp expression in cells harboring mdr1. Photoaffinity labeling experiment performed with the P-gp ligand [125I]iodoarylazidoprazosin demonstrated that compounds that induced or inhibited P-gp transport activity also bound to P-gp. DEET was also found to be a potent inhibitor of P-gp-mediated ATPase activity, whereas pyridostigmine bromide increased P-gp ATPase activity. Cells expressing P-gp or lac permease were exposed to pyridostigmine bromide and DEET, alone and in combination. Noncytotoxic concentrations of DEET significantly inhibited P-gp-mediated resistance against pyridostigmine bromide, resulting in a reduction of the number of effective drug interactions with biological targets. An explanation of

Aclidinium bromide plus formoterol for the treatment of chronic obstructive pulmonary disease.

PubMed

Lal, Chitra; Strange, Charlie

2015-02-01

Drugs that target dynamic hyperinflation such as long-acting β-2 agonists and long-acting antimuscarinic antagonists form a cornerstone of chronic obstructive pulmonary disease (COPD) management. The idea of combining these two medications in a single formulation, which may potentially improve patient compliance, is novel and attractive. The pharmacologic profiles of aclidinium bromide and formoterol fumarate are discussed. However, studies to define drug interactions and alterations in the pharmacodynamics and pharmacokinetics of the fixed dose combination (FDC) of aclidinium bromide/formoterol fumarate in large populations remain unpublished. Results of Phase II and two Phase III pivotal trials, ACLIFORM/COPD and AUGMENT COPD, evaluating the FDC are discussed. Initial data for the aclidinium/formoterol inhaler appears to be promising for impacting the lung function. To define if this benefit translates into improved long-term outcomes of decreased exacerbation frequency, improved quality of life and decreased disease-specific mortality are important. The introduction of this combination will likely have a significant impact on the prescribing habits of physicians across the world.

Molecular structure of the dioctadecyldimethylammonium bromide (DODAB) bilayer.

PubMed

Jamróz, Dorota; Kepczynski, Mariusz; Nowakowska, Maria

2010-10-05

Dioctadecyldimethylammonium bromide (DODAB) is a double-chained quaternary ammonium surfactant that assembles in water into bilayer structures. This letter reports the molecular dynamics (MD) computer simulations of the DODAB bilayer at 25 °C. The simulations show that the surfactant membrane arranges spontaneously into the rippled phase (P(β)(')) at that temperature. The ordering within the chain fragment closest to the hydrophilic head (carbon atoms 1-5) is relatively low. It grows significantly for the carbon atoms located in the center of the membrane (atoms 6-17). The C6-C17 chain fragments are well aligned and tilted by ca. 15° with respect to the bilayer normal.

A Systematic Study on the Mesomorphic Behavior of Asymmetrical 1-Alkyl-3-dodecylimidazolium Bromides

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Mei; Mallick, Bert; Mudring, Anja-Verena

2014-04-02

To determine the essential parameters for mesophase formation in imidazolium-based ionic liquids (ILs), a library of 1-alkyl-3-dodecylimidazolium bromides was synthesized, abbreviated as CnC12, where 0 ≤ n ≤ 13, as the general notion is that a dodecyl side chain would guarantee the formation of an ionic liquid crystal (ILC). All salts were fully characterized by NMR spectroscopy and mass spectrometry. Their thermal properties were recorded, and mesophase formation was assessed. An odd–even effect is observed for 5 ≤ n ≤ 10 in the temperatures of melting transitions. While the majority of this series, as expected, formed mesophases, surprisingly compounds C2C12more » and C6C12 could not be classified as ILCs, the latter being a room temperature IL, while C2C12 is a crystalline solid with melting point at 37 °C. The single crystal structure of compound 1-ethyl-3-dodecylimidazolium bromide (C2C12) was successfully obtained. Remarkably, the arrangement of imidazolium cores in the structure is very complicated due to multiple nonclassical hydrogen bonds between bromide anions and imidazolium head groups. In this arrangement, neighboring imidazolium rings are forced by hydrogen bonds to form a “face-to-face” conformation. This seems to be responsible for the elimination of a mesophase. To conclude, the general view of a dodecyl chain being a functional group to generate a mesophase is not entirely valid.« less

Preparation and optical characteristics of layered perovskite-type lead-bromide-incorporated azobenzene chromophores

NASA Astrophysics Data System (ADS)

Sasai, Ryo; Shinomura, Hisashi

2013-02-01

Lead bromide-based layered perovskite powders with azobenzene derivatives were prepared by a homogeneous precipitation method. From the diffuse reflectance (DR) and photoluminescence (PL) spectra of the hybrid powder materials, the present hybrids exhibited sharp absorption and PL peaks originating from excitons produced in the PbBr42- layer. When the present hybrid powder was irradiated with UV light at 350 nm, the absorption band from the trans-azobenzene chromophore, observed around 350 nm, decreased, while the absorption band from the cis-azobenzene chromophore, observed around 450 nm, increased. These results indicate that azobenzene chromophores in the present hybrid materials exhibit reversible photoisomerization. Moreover, it was found that the PL intensity from the exciton also varied due to photoisomerization of the azobenzene chromophores in the present hybrid. Thus, for the first time we succeeded in preparing the azobenzene derivative lead-bromide-based layered perovskite with photochromism before and after UV light irradiation.

IDENTIFICATION OF NEW DRINKING WATER DISINFECTION BY-PRODUCTS FORMED IN THE PRESENCE OF BROMIDE

EPA Science Inventory

Using a combination of mass spectrometry and infrared spectroscopy, disinfection by-products (DBPs) were identified in ozonated drinking water containing elevated bromide levels, and in ozonated water treated with secondary chlorine or chloramine. Only one brominated by-product-d...

Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Treatment 8 Hours or Less

EPA Pesticide Factsheets

This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Treatment Longer than 8 Hours

EPA Pesticide Factsheets

This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

Analysis of genotoxic activity of ketamine and rocuronium bromide using the somatic mutation and recombination test in Drosophila melanogaster.

PubMed

Koksal, Pakize Muge; Gürbüzel, Mehmet

2015-03-01

The present study evaluated the mutagenic and recombinogenic effects of two commonly used anesthetic agents, ketamine and rocuronium bromide, in medicine using the wing somatic mutation and recombination test (SMART) in Drosophila. The standard (ST) cross and the high-bioactivation (HB) cross with high sensitivity to procarcinogens and promutagens were used. The SMART test is based on the loss of heterozygosity, which occurs via various mechanisms, such as chromosome loss and deletion, half-translocation, mitotic recombination, mutation, and non-disjunction. Genetic alterations occurring in the somatic cells of the wing's imaginal discs result in mutant clones in the wing blade. Three-day-old trans-heterozygous larvae with two recessive markers, multiple wing hairs (mwh) and flare (flr(3)), were treated with ketamine and rocuronium bromide. Analysis of the ST cross indicated that ketamine exhibited genotoxicity activity and that this activity was particularly dependent on homologous mitotic recombination at concentrations of 250 μg/ml and above. Rocuronium bromide did not exert mutagenic and/or recombinogenic effects. In the HB cross, ketamine at a concentration of 1000 μg/ml and rocuronium bromide at all concentrations, with the exception of 250 μg/ml (inconclusive), exerted genotoxic effects, which could also be associated with the increase in mitotic recombination. Copyright © 2015 Elsevier B.V. All rights reserved.

Comments on alternatives to methyl bromide for quarantine purposes in forest nurseries

Treesearch

David B. South

2008-01-01

Viewpoints will vary in regards to the best alternative to methyl bromide (CH3Br) fumigation. In some cases, crop value will determine the best alternative. As the value of the crop increases, the rate (and cost) of the "best" treatment might increase as well. In addition, the recommendation will depend on if the individual has a "...

Evaluating equilibrium and non-equilibrium transport of bromide and isoproturon in disturbed and undisturbed soil columns.

PubMed

Dousset, S; Thevenot, M; Pot, V; Simunek, J; Andreux, F

2007-12-07

In this study, displacement experiments of isoproturon were conducted in disturbed and undisturbed columns of a silty clay loam soil under similar rainfall intensities. Solute transport occurred under saturated conditions in the undisturbed soil and under unsaturated conditions in the sieved soil because of a greater bulk density of the compacted undisturbed soil compared to the sieved soil. The objective of this work was to determine transport characteristics of isoproturon relative to bromide tracer. Triplicate column experiments were performed with sieved (structure partially destroyed to simulate conventional tillage) and undisturbed (structure preserved) soils. Bromide experimental breakthrough curves were analyzed using convective-dispersive and dual-permeability (DP) models (HYDRUS-1D). Isoproturon breakthrough curves (BTCs) were analyzed using the DP model that considered either chemical equilibrium or non-equilibrium transport. The DP model described the bromide elution curves of the sieved soil columns well, whereas it overestimated the tailing of the bromide BTCs of the undisturbed soil columns. A higher degree of physical non-equilibrium was found in the undisturbed soil, where 56% of total water was contained in the slow-flow matrix, compared to 26% in the sieved soil. Isoproturon BTCs were best described in both sieved and undisturbed soil columns using the DP model combined with the chemical non-equilibrium. Higher degradation rates were obtained in the transport experiments than in batch studies, for both soils. This was likely caused by hysteresis in sorption of isoproturon. However, it cannot be ruled out that higher degradation rates were due, at least in part, to the adopted first-order model. Results showed that for similar rainfall intensity, physical and chemical non-equilibrium were greater in the saturated undisturbed soil than in the unsaturated sieved soil. Results also suggested faster transport of isoproturon in the undisturbed soil due

Evaluating equilibrium and non-equilibrium transport of bromide and isoproturon in disturbed and undisturbed soil columns

NASA Astrophysics Data System (ADS)

Dousset, S.; Thevenot, M.; Pot, V.; Šimunek, J.; Andreux, F.

2007-12-01

In this study, displacement experiments of isoproturon were conducted in disturbed and undisturbed columns of a silty clay loam soil under similar rainfall intensities. Solute transport occurred under saturated conditions in the undisturbed soil and under unsaturated conditions in the sieved soil because of a greater bulk density of the compacted undisturbed soil compared to the sieved soil. The objective of this work was to determine transport characteristics of isoproturon relative to bromide tracer. Triplicate column experiments were performed with sieved (structure partially destroyed to simulate conventional tillage) and undisturbed (structure preserved) soils. Bromide experimental breakthrough curves were analyzed using convective-dispersive and dual-permeability (DP) models (HYDRUS-1D). Isoproturon breakthrough curves (BTCs) were analyzed using the DP model that considered either chemical equilibrium or non-equilibrium transport. The DP model described the bromide elution curves of the sieved soil columns well, whereas it overestimated the tailing of the bromide BTCs of the undisturbed soil columns. A higher degree of physical non-equilibrium was found in the undisturbed soil, where 56% of total water was contained in the slow-flow matrix, compared to 26% in the sieved soil. Isoproturon BTCs were best described in both sieved and undisturbed soil columns using the DP model combined with the chemical non-equilibrium. Higher degradation rates were obtained in the transport experiments than in batch studies, for both soils. This was likely caused by hysteresis in sorption of isoproturon. However, it cannot be ruled out that higher degradation rates were due, at least in part, to the adopted first-order model. Results showed that for similar rainfall intensity, physical and chemical non-equilibrium were greater in the saturated undisturbed soil than in the unsaturated sieved soil. Results also suggested faster transport of isoproturon in the undisturbed soil due

Synthesis and characterization of [BMIM]bromide using microwave-assisted organic synthesis method and its application for dissolution of palm empty fruit bunch

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arianie, Lucy, E-mail: lucy205@yahoo.com; Wahyuningrum, Deana, E-mail: deana@chem.itb.ac.id; Nurrachman, Zeily, E-mail: deana@chem.itb.ac.id

The decrease of cellulose crystallinity index of palm empty fruit bunch is crucial for the next application of cellulose as raw material for various biofuel and its derivatives. The aim of this research is to decrease the cellulose crystallinity index of palm empty fruit bunch using 1-butyl-3-methylimidazoliumbromide or [BMIM] bromide which has been synthesized using Microwave-Assisted Organic Synthesis (MAOS) method. Conventional reaction method has also been carried out to synthesize [BMIM]bromide for comparison as well. The characterization of synthesized product using FTIR, {sup 1}H-NMR, {sup 13}C-NMR and LC-MS showed that these reactions have been carried out successfully. The results showedmore » that MAOS method is up to 90% faster in producing [BMIM]bromide compare to the conventional method. The application of [BMIM]bromide for dissolution of palm empty fruit bunch showed that cellulose and lignin could be extracted using stirring process for 20 hours. The decrease of cellulose crystallinity index and its morphology changes were identified using FTIR and Scanning Electron Microscope.« less

Synthesis and characterization of [BMIM]bromide using microwave-assisted organic synthesis method and its application for dissolution of palm empty fruit bunch

NASA Astrophysics Data System (ADS)

Arianie, Lucy; Wahyuningrum, Deana; Nurrachman, Zeily; Natalia, Dessy

2014-03-01

The decrease of cellulose crystallinity index of palm empty fruit bunch is crucial for the next application of cellulose as raw material for various biofuel and its derivatives. The aim of this research is to decrease the cellulose crystallinity index of palm empty fruit bunch using 1-butyl-3-methylimidazoliumbromide or [BMIM] bromide which has been synthesized using Microwave-Assisted Organic Synthesis (MAOS) method. Conventional reaction method has also been carried out to synthesize [BMIM]bromide for comparison as well. The characterization of synthesized product using FTIR, 1H-NMR, 13C-NMR and LC-MS showed that these reactions have been carried out successfully. The results showed that MAOS method is up to 90% faster in producing [BMIM]bromide compare to the conventional method. The application of [BMIM]bromide for dissolution of palm empty fruit bunch showed that cellulose and lignin could be extracted using stirring process for 20 hours. The decrease of cellulose crystallinity index and its morphology changes were identified using FTIR and Scanning Electron Microscope.

The discovery and development of aclidinium bromide for the treatment of chronic obstructive pulmonary disease.

PubMed

Malerba, Mario; Radaeli, Alessandro; Santini, Giuseppe; Morjaria, Jaymin; Mores, Nadia; Mondino, Chiara; Macis, Giuseppe; Montuschi, Paolo

2018-06-01

Bronchodilators, including long-acting muscarinic receptor antagonists (LAMAs), are a mainstay of the pharmacological treatment of chronic obstructive pulmonary disease (COPD). LAMAs act as bronchodilators principally by antagonizing airway smooth muscle cells M 3 muscarinic receptors. Aclidinium bromide is a twice-daily LAMA which was developed to improve on the efficacy and/or safety of previous LAMAs. Area covered: Herein, the authors present the pharmacotherapeutic role of aclidinium in COPD and point out unmet need in this research area. The following aspects are covered: a) the discovery and medicinal chemistry of aclidinium bromide; b) an overview of the market; c) its mechanism of action; d) its pharmacokinetic/pharmacodynamic profile derived from pre-clinical studies; e) the clinical studies which led to its licensing; f) the evidence from meta-analyses; g) the aclidinium/formoterol fixed dose combination for COPD and h) priorities in this area of research. Expert opinion: Aclidinium bromide has the pharmacological properties, safety and efficacy profile and inhaler characteristics which makes it a valuable therapeutic option for pharmacological management of patients with COPD. Due to its rapid biotransformation into inactive metabolites, aclidinium is potentially one of the safest LAMAs. Further head-to-head randomized clinical trials are required to define efficacy and safety of aclidinium when compared to once-daily LAMAs. The clinical relevance of airway anti-remodeling effects of aclidinium has to be defined.

Deswelling kinetics of polyacrylate gels in solutions of cetyltrimethylammonium bromide.

PubMed

Nilsson, Peter; Hansson, Per

2007-08-23

The deswelling kinetics of single sodium polyacrylate gel beads (radius 40-160 microm) in aqueous solutions of cetyltrimethylammonium bromide under conditions of forced convection are investigated using micromanipulator assisted light microscopy. The purpose of the study is to further evaluate a previously published model (J. Phys. Chem. B 2003, 107, 9203) using a higher homolog surfactant. For gels with expected fast deswelling (small gel size/low surfactant concentration) and/or in low electrolyte concentration, the model is found to correctly predict the deswelling characteristics of the gel beads. However, for some gels with expected slow deswelling, especially in high electrolyte concentration (10 mM NaBr), the model widely underestimates the required deswelling time. The reason for this is argued to be the longer time frame and high bromide concentration allowing the formation of a denser, more ordered structure in the surface phase, which resists the deformation and reorganization of material necessary for deswelling. Unexpectedly long lag times before the start of deswelling are also found for gels in low surfactant concentration, indicating that a relatively high surfactant concentration in the gel, greatly exceeding the critical aggregation concentration, is needed to start formation of a collapsed surface phase. This critical surfactant concentration is found to be dependent on initial gel radius, as small gels require a relatively higher concentration to initiate collapse.

CHLORPYRIFOS TRANSFORMATION BY AQUEOUS CHLORINE IN THE PRESENCE OF BROMIDE AND NATURAL ORGANIC MATTER

EPA Science Inventory

The aqueous chlorination of chlorpyrifos (CP) was investigated in the presence of bromide and natural organic matter (NOM), which were identified as naturally occurring aqueous constituents that could impact CP transformation rates to the toxic product chlorpyrifos oxon (CPO). Br...

Iron-catalyzed cross-coupling of N-heterocyclic chlorides and bromides with arylmagnesium reagents.

PubMed

Kuzmina, Olesya M; Steib, Andreas K; Flubacher, Dietmar; Knochel, Paul

2012-09-21

A simple, practical iron salt catalyzed procedure allows fast cross-couplings of N-heterocyclic chlorides and bromides with various electron-rich and -poor arylmagnesium reagents. A solvent mixture of THF and tBuOMe is found to be essential for achieving high yields mainly by avoiding homocoupling side reactions.

High-performance liquid chromatographic determination of pyridostigmine bromide, nicotine, and their metabolites in rat plasma and urine.

PubMed

Abu-Qare, A W; Abou-Donia, M B

2001-07-01

This study reports on the development of a rapid and simple method for the determination of the antinerve agent drug pyridostigmine bromide (3-dimethylaminocarbonyloxy-N-methyl pyridinium bromide) (PB), its metabolite N-methyl-3-hydroxypyridinium bromide, nicotine (S-1-methyl-5-(3-pyridyl)-2-pyrrolidine), and its metabolites nornicotine (2-(3-pyridyl)pyrrolidine) and cotinine (S-1-methyl-5-(3-pyridyl)-2-pyrrolidone) in rat plasma and urine. The compounds are extracted and eluted by methanol and acetonitrile using C18 Sep-Pak cartridges and separated using high-performance liquid chromatography by a gradient of methanol, acetonitrile, and water (pH 3.2) at a flow rate of 0.8 mL/min in a period of 14 min. UV detection was at 260 nm for nicotine and its metabolites and at 280 nm for PB and its metabolite. The limits of detection ranged between 20 and 70 ng/mL, and the limits of quantitation were 50-100 ng/mL. The average percent recovery of five spiked plasma samples were 85.7 +/- 7.3%, 80.4 +/- 5.8%, 78.9 +/- 5.4%, 76.7 +/- 6.4%, and 79.7 +/- 5.7% and for urine were 85.9 +/- 5.9%, 75.5 +/- 6.9%, 82.6 +/- 7.9%, 73.6 +/- 5.9%, and 77.7 +/- 6.3% for nicotine, nornicotine, cotinine, PB, and N-methyl-3-hydroxypyridinium bromide, respectively. The calibration curves for standard solutions of the compounds of peak areas and concentration are linear for a range between 100 and 1,000 ng/mL. This method is applied in order to analyze the previously mentioned chemicals and metabolites following their oral administration in rats.

Estimating groundwater recharge in Hebei Plain, China under varying land use practices using tritium and bromide tracers

NASA Astrophysics Data System (ADS)

Wang, Bingguo; Jin, Menggui; Nimmo, John R.; Yang, Lei; Wang, Wenfeng

2008-07-01

SummaryTritium and bromide were used as applied tracers to determine groundwater recharge in Hebei Plain, North China, to evaluate the impacts of different soil types, land use, irrigation, and crop cultivation practice on recharge. Additional objectives were to evaluate temporal variability of recharge and the effect on results of the particular tracer used. Thirty-nine profiles at representative locations were chosen for investigation. Average recharge rates and recharge coefficient determined by tritium and bromide tracing for different sites were 0.00-1.05 mm/d and 0.0-42.5%, respectively. The results showed relative recharge rates for the following paired influences (items within each pair are listed with the influence producing greater recharge first): flood-irrigated cropland and non-irrigated non-cultivation land, flood irrigation (0.42-0.58 mm/d) and sprinkling irrigation (0.17-0.23 mm/d), no stalk mulch (0.56-0.80 mm/d) and stalk mulch (0.44-0.60 mm/d), vegetable (e.g. Chinese cabbage and garlic, 0.70 mm/d) and wheat-maize (0.38 mm/d), peanut (0.51 mm/d) and peach (0.43 mm/d). The results also showed greater recharge for the first year of tracer travel than for the second. Because total precipitation and irrigation were greater in the first year than in the second, this may reflect temporal variability of recharge. The method may not be applicable where the water table is shallow (less than 3 m). A comparison of the near-ideal tritium tracer with the more common but less ideal bromide showed that bromide moved approximately 23% faster than tritiated water, perhaps because of anion exclusion.

Estimating groundwater recharge in Hebei Plain, China under varying land use practices using tritium and bromide tracers

USGS Publications Warehouse

Wang, B.; Jin, M.; Nimmo, J.R.; Yang, L.; Wang, W.

2008-01-01

Tritium and bromide were used as applied tracers to determine groundwater recharge in Hebei Plain, North China, to evaluate the impacts of different soil types, land use, irrigation, and crop cultivation practice on recharge. Additional objectives were to evaluate temporal variability of recharge and the effect on results of the particular tracer used. Thirty-nine profiles at representative locations were chosen for investigation. Average recharge rates and recharge coefficient determined by tritium and bromide tracing for different sites were 0.00-1.05 mm/d and 0.0-42.5%, respectively. The results showed relative recharge rates for the following paired influences (items within each pair are listed with the influence producing greater recharge first): flood-irrigated cropland and non-irrigated non-cultivation land, flood irrigation (0.42-0.58 mm/d) and sprinkling irrigation (0.17-0.23 mm/d), no stalk mulch (0.56-0.80 mm/d) and stalk mulch (0.44-0.60 mm/d), vegetable (e.g. Chinese cabbage and garlic, 0.70 mm/d) and wheat-maize (0.38 mm/d), peanut (0.51 mm/d) and peach (0.43 mm/d). The results also showed greater recharge for the first year of tracer travel than for the second. Because total precipitation and irrigation were greater in the first year than in the second, this may reflect temporal variability of recharge. The method may not be applicable where the water table is shallow (less than 3 m). A comparison of the near-ideal tritium tracer with the more common but less ideal bromide showed that bromide moved approximately 23% faster than tritiated water, perhaps because of anion exclusion. ?? 2008 Elsevier B.V.

Ni-catalyzed reductive homocoupling of unactivated alkyl bromides at room temperature and its synthetic application.

PubMed

Peng, Yu; Luo, Long; Yan, Chang-Song; Zhang, Jian-Jian; Wang, Ya-Wen

2013-11-01

A room-temperature Ni-catalyzed reductive approach to homocoupling of unactivated primary, secondary, and tertiary alkyl bromides is described. The catalytic system can be easily generated from air-stable and cheap materials and demonstrates broad functional group tolerance, thus allowing facile access to useful dimeric triterpene and lignan-like molecules. Moreover, the dimerization of tertiary bromide 6 efficiently establishes sterically hindered vicinal quaternary carbons (C3a and C3a'), which is a key linkage of intriguing bispyrrolo[2,3-b]indoline alkaloids, thereby enabling us to complete the total syntheses of racemic chimonanthine (9) and folicanthine (10). In addition, this dimerization method can be expanded to the highly stereoselective synthesis of bisperhydrofuro[2,3-b]furan (5a) and the dimeric spiroketal 5b, signifying the involvement of possible radical species.

Evaluation of non-fumigant pesticides as methyl bromide alternatives for managing weeds in vegetables

USDA-ARS?s Scientific Manuscript database

The phase out of methyl bromide challenged vegetable growers’ abilities to control weeds in low-density polyethylene (LDPE) mulch production systems. The herbicides halosulfuron, fomesafen, s-metolachlor, and clomazone are needed as part of the pesticide program in LDP vegetable production to contr...

Bromidotetra-kis-(2-isopropyl-1H-imidazole-κN)copper(II) bromide.

PubMed

Godlewska, Sylwia; Socha, Joanna; Baranowska, Katarzyna; Dołęga, Anna

2011-10-01

The Cu(II) atom in the title salt, [CuBr(C(6)H(10)N(2))(4)]Br, is coordinated in a square-pyramidal geometry by four imidazole N atoms and one bromide anion that is located at the apex of the pyramid. The cations and the anions form a two-dimensional network parallel to (001) through N-H⋯Br hydrogen bonds.

Determination of depleted uranium, pyridostigmine bromide and its metabolite in plasma and urine following combined administration in rats.

PubMed

Abu-Qare, A W; Abou-Donia, M B

2001-09-01

A simple and reliable method was developed for the quantification of depleted uranium, the anti nerve agent drug pyridostigmine bromide (PB;3-dimethylaminocarbonyloxy-N-methyl pyridinium bromide) and its metabolite N-methyl-3-hydroxypyridinium bromide in rat plasma and urine. The method involved using solid phase extraction and spectrophotometric determination of uranium, and high performance liquid chromatography (HPLC) with reversed phase C(18) column, and UV detection at 280 nm for PB and its metabolite. Uranium was derivatized using dibenzoylmethane (DBM) then the absorbance was measured at 405 nm. PB and its metabolite were separated using a gradient of 1--40% acetonitrile in 0.1% triflouroacetic acid water solution (pH 3.2) at a flow rate of 0.8 ml/min in a period of 14 min. Limits of detection were 2 ng/ml for uranium and 50 ng/ml for PB and its metabolite. Limits of quantitation were between 10 and 100 ng/ml for uranium and the other two analytes, respectively. Average percentage recovery of five spiked plasma samples were 83.7+/-8.6, 76.8+/-6.7, 79.1+/-7.1, and from urine 82.7+/-8.6, 79.3+/-9.5 and 78.0+/-6.2, for depleted uranium, PB and N-methyl-3-hydroxypyridinium bromide, respectively. The relationship between peak areas and concentration was linear for standards between 100 and 1000 ng/ml for all three analytes. This method was applied to analyze the above chemicals and metabolites following combined administration in rats.

Treatment of Dysphagia with pyridostigmine bromide in a patient with the pharyngeal-cervical-brachial variant of guillain-barré syndrome.

PubMed

Lee, Kwang Lae; Lim, Oh Kyung; Lee, Ju Kang; Park, Ki Deok

2012-02-01

A 24-year-old male developed bulbar palsy, ophthalmoplegia, ptosis, and shoulder weakness bilaterally 2 weeks after he had experienced an upper respiratory infection. The electrodiagnostic study demonstrated axonal polyradiculoneuropathy. The repetitive nerve stimulation study (RNS) showed no significant decrement of the compound muscle action potentials (CMAPs). The videofluoroscopic swallowing study (VFSS) showed severe impairment of the pharyngeal phase of swallowing. He was diagnosed as having the pharyngeal-cervical-brachial variant of Guillain-Barré syndrome. The patient's dysphagia was not improved for 3 months. A follow up RNS showed a significant decrement of the CMAPs. Pyridostigmine bromide was tried to improve the dysphagia. The patient showed immediate improvement of his dysphagia on the VFSS after the trial with pyridostigmine bromide. Pyridostigmine bromide was given before each meal for 8 days and he showed continuous improvement of his dysphagia. The follow up VFSS after 3 months showed complete recovery of dysphagia.

[Cetyltrimethylammonium bromide for fluorescence enhancement of anhydrotetracycline hydrochloride and iso-tetracycline].

PubMed

Zha, Jian-peng; Lin, Ying; Yang, Xing-hui; Hou, Hai-ni; Wei, Tie-jun; Chen, Xing-li

2002-06-01

Fluorescence enhancement of anhydrotetracycline hydrochloride and iso-tetracycline has been described. The fluorescence intensities of anhydrotetracycline hydrochloride and iso-tetracycline with cetyltrimethylammonium bromide (CTMAB) enhanced by micellar solution have been examined. It is found that fluorescence enhancement of anhydrotetracycline hydrochloride and iso-tetracycline depends on the concentration of CTMAB and pH of the solution. It can be used to develop sensitive methods for the determination of tetracycline hydrochloride and its decomposition product.

Chlorination of bromide-containing waters: enhanced bromate formation in the presence of synthetic metal oxides and deposits formed in drinking water distribution systems.

PubMed

Liu, Chao; von Gunten, Urs; Croué, Jean-Philippe

2013-09-15

Bromate formation from the reaction between chlorine and bromide in homogeneous solution is a slow process. The present study investigated metal oxides enhanced bromate formation during chlorination of bromide-containing waters. Selected metal oxides enhanced the decay of hypobromous acid (HOBr), a requisite intermediate during the oxidation of bromide to bromate, via (i) disproportionation to bromate in the presence of nickel oxide (NiO) and cupric oxide (CuO), (ii) oxidation of a metal to a higher valence state in the presence of cuprous oxide (Cu2O) and (iii) oxygen formation by NiO and CuO. Goethite (α-FeOOH) did not enhance either of these pathways. Non-charged species of metal oxides seem to be responsible for the catalytic disproportionation which shows its highest rate in the pH range near the pKa of HOBr. Due to the ability to catalyze HOBr disproportionation, bromate was formed during chlorination of bromide-containing waters in the presence of CuO and NiO, whereas no bromate was detected in the presence of Cu2O and α-FeOOH for analogous conditions. The inhibition ability of coexisting anions on bromate formation at pH 8.6 follows the sequence of phosphate > sulfate > bicarbonate/carbonate. A black deposit in a water pipe harvested from a drinking water distribution system exerted significant residual oxidant decay and bromate formation during chlorination of bromide-containing waters. Energy dispersive spectroscopy (EDS) analyses showed that the black deposit contained copper (14%, atomic percentage) and nickel (1.8%, atomic percentage). Cupric oxide was further confirmed by X-ray diffraction (XRD). These results indicate that bromate formation may be of concern during chlorination of bromide-containing waters in distribution systems containing CuO and/or NiO. Copyright © 2013 Elsevier Ltd. All rights reserved.

Dual role of allylsamarium bromide as a Grignard reagent and a single electron transfer reagent in the one-pot synthesis of terminal olefins.

PubMed

Li, Ying; Hu, Yuan-Yuan; Zhang, Song-Lin

2013-11-21

The utility of allylsamarium bromide, both as a nucleophilic reagent and a single-electron transfer reagent, in the reaction of carbonyl compounds with allylsamarium bromide in the presence of diethyl phosphate is reported in this communication. From a synthetic point of view, a simple one-pot method for the preparation of terminal olefins is developed.

Mild copper-catalyzed vinylation reactions of azoles and phenols with vinyl bromides.

PubMed

Taillefer, Marc; Ouali, Armelle; Renard, Brice; Spindler, Jean-Francis

2006-07-05

An efficient and straightforward copper-catalyzed method allowing vinylation of N- or O-nucleophiles with di- or trisubstituted vinyl bromides is reported. The procedure is applicable to a broad range of substrates since N-vinylation of mono-, di-, and triazoles as well as O-vinylation of phenol derivatives can be performed with catalytic amounts of copper iodide and inexpensive nitrogen ligands 3 or 8. In the case of more hindered vinyl bromides, the use of the original bidentate chelator 8 was shown to be more efficient to promote the coupling reactions than our key tetradentate ligand 3. The corresponding N-(1-alkenyl)azoles and alkenyl aryl ethers are obtained in high yields and selectivities under very mild temperature conditions (35-110 degrees C for N-vinylation reactions and 50-80 degrees C for O-vinylation reactions). Moreover, to our knowledge, this method is the first example of a copper-catalyzed vinylation of various azoles. Finally, this protocol, practical on a laboratory scale and easily adaptable to an industrial scale, is very competitive compared to the existing methods that allow the synthesis of such compounds.

The use of agricultural by-products to capture methyl bromide following post-harvest fumigation

USDA-ARS?s Scientific Manuscript database

Activated carbons were prepared from plum and peach stone as well as almond and walnut shell and comparatively evaluated as sorbents to minimize the atmospheric emission of methyl bromide following postharvest fumigations. A variety of methods were used to make the activated carbons and each is desc...

Volatilization Mechanism of 1-Ethyl-3-methylimidazolium Bromide Ionic Liquid (Briefing Charts)

DTIC Science & Technology

2012-04-01

bromides and alkylimidazoles, presumably through alkyl abstraction via an SN2 type mechanism, and that vaporization of intact ion pairs or the formation...116.1±6.6 kJ/mol and H.‡(CH3CH2Br) = 122.9±7.2 kJ/mol, and the results are found to be in agreement with calculated values for the SN2 reactions

Degradation of methyl bromide in anaerobic sediments

USGS Publications Warehouse

Oremland, R.S.; Miller, L.G.; Strohmaler, F.E.

1994-01-01

Methyl bromide (MeBr) was anaerobically degraded in saltmarsh sediments after reaction with sulfide. The product of this nucleophilic substitution reaction was methanethiol, which underwent further chemical and bacterial reactions to form dimethyl sulfide. These two gases appeared transiently during sediment incubations because they were metabolized by methanogenic and sulfate-reducing bacteria. A second, less significant reaction of MeBr was the exchange with chloride, forming methyl chloride, which was also susceptible to attack by sulfide. Incubation of 14C-labeled methyl iodide as an analogue of MeBr resulted in the formation of 14CH4 and 14CO2 and also indicated that sulfate-reducing bacteria as well as methanogens metabolized the methylated sulfur intermediates. These results suggest that exposed sediments with abundant free sulfide, such as coastal salt-marshes, may constitute a sink for atmospheric MeBr.

Bromide-free TEMPO-mediated oxidation of primary alcohol groups in starch and methyl alpha-D-glucopyranoside.

PubMed

Bragd, P L; Besemer, A C; van Bekkum, H

2000-09-22

TEMPO (2,2,6,6-tetramethylpiperidine-1-oxyl)-mediated oxidation of potato starch and methyl alpha-D-glucopyranoside (MGP) was performed in the absence of sodium bromide (NaBr) as co-catalyst, solely using sodium hypochlorite (NaOCl) as the primary oxidant. The low reaction rate associated with a bromide-free process was increased by performing the oxidation at increased temperatures. The reaction proceeded stoichiometrically and with high selectivity and with only minor depolymerisation, provided that temperature and pH were kept < or = 20 degrees C and < 9.0, respectively. At 20 degrees C and pH 8.5, the reaction rate was comparable to that of a corresponding oxidation catalysed by NaBr at 2 degrees C. Consequently, this is a simple approach to raise the TEMPO/NaOCl reaction rate under bromide-free conditions while still maintaining good product properties. At higher oxidation temperatures (> or = 25 degrees C) and under more alkaline conditions (pH > or = 9.0) degradation of the starch skeleton occurred. Simultaneously, side-reactions of the nitrosonium ion lowered the yield of the oxidation. Despite the absence of the NaBr catalyst, the reaction rate-controlling step was found to be the oxidation of the primary hydroxyl groups with the nitrosonium ion. The reaction was first-order in MGP and in TEMPO.

Treatment of Dysphagia with Pyridostigmine Bromide in a Patient with the Pharyngeal-Cervical-Brachial Variant of Guillain-Barré Syndrome

PubMed Central

Lee, Kwang Lae; Lim, Oh Kyung; Park, Ki Deok

2012-01-01

A 24-year-old male developed bulbar palsy, ophthalmoplegia, ptosis, and shoulder weakness bilaterally 2 weeks after he had experienced an upper respiratory infection. The electrodiagnostic study demonstrated axonal polyradiculoneuropathy. The repetitive nerve stimulation study (RNS) showed no significant decrement of the compound muscle action potentials (CMAPs). The videofluoroscopic swallowing study (VFSS) showed severe impairment of the pharyngeal phase of swallowing. He was diagnosed as having the pharyngeal-cervical-brachial variant of Guillain-Barré syndrome. The patient's dysphagia was not improved for 3 months. A follow up RNS showed a significant decrement of the CMAPs. Pyridostigmine bromide was tried to improve the dysphagia. The patient showed immediate improvement of his dysphagia on the VFSS after the trial with pyridostigmine bromide. Pyridostigmine bromide was given before each meal for 8 days and he showed continuous improvement of his dysphagia. The follow up VFSS after 3 months showed complete recovery of dysphagia. PMID:22506249

77 FR 31564 - Notice of Availability of a Treatment Evaluation Document; Methyl Bromide Fumigation of Cottonseed

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-29

... significant impacts on U.S. cotton production. They are currently found only in Australia. Fumigation with methyl bromide was the only approved treatment for FOV VCG 01111 and 01112, so when the Environmental...

The history and future of methyl bromide alternatives in the southern United States

Treesearch

Tom E. Starkey

2012-01-01

This article gives a brief history of the efforts of the Southern Forest Nursery Management Cooperative (SFNMC) in testing methyl bromide (MBr) alternatives for soil fumigation. In the southeastern United States, fumigation with MBr has been the most commonly used method for producing high quality, pest-free forest seedlings in an environment that is conducive for soil...

Effect of chronic administration of phenobarbital, or bromide, on pharmacokinetics of levetiracetam in dogs with epilepsy.

PubMed

Muñana, K R; Nettifee-Osborne, J A; Papich, M G

2015-01-01

Levetiracetam (LEV) is a common add-on antiepileptic drug (AED) in dogs with refractory seizures. Concurrent phenobarbital administration alters the disposition of LEV in healthy dogs. To evaluate the pharmacokinetics of LEV in dogs with epilepsy when administered concurrently with conventional AEDs. Eighteen client-owned dogs on maintenance treatment with LEV and phenobarbital (PB group, n = 6), LEV and bromide (BR group, n = 6) or LEV, phenobarbital and bromide (PB-BR group, n = 6). Prospective pharmacokinetic study. Blood samples were collected at 0, 1, 2, 4, and 6 hours after LEV administration. Plasma LEV concentrations were determined by high-pressure liquid chromatography. To account for dose differences among dogs, LEV concentrations were normalized to the mean study dose (26.4 mg/kg). Pharmacokinetic analysis was performed on adjusted concentrations, using a noncompartmental method, and area-under-the-curve (AUC) calculated to the last measured time point. Compared to the PB and PB-BR groups, the BR group had significantly higher peak concentration (Cmax ) (73.4 ± 24.0 versus 37.5 ± 13.7 and 26.5 ± 8.96 μg/mL, respectively, P < .001) and AUC (329 ± 114 versus 140 ± 64.7 and 98.7 ± 42.2 h*μg/mL, respectively, P < .001), and significantly lower clearance (CL/F) (71.8 ± 22.1 versus 187 ± 81.9 and 269 ± 127 mL/h/kg, respectively, P = .028). Concurrent administration of PB alone or in combination with bromide increases LEV clearance in epileptic dogs compared to concurrent administration of bromide alone. Dosage increases might be indicated when utilizing LEV as add-on treatment with phenobarbital in dogs. Copyright © 2015 by the American College of Veterinary Internal Medicine.

Four groups of new aromatic halogenated disinfection byproducts: effect of bromide concentration on their formation and speciation in chlorinated drinking water.

PubMed

Pan, Yang; Zhang, Xiangru

2013-02-05

Bromide is naturally present in source waters worldwide. Chlorination of drinking water can generate a variety of chlorinated and brominated disinfection byproducts (DBPs). Although substantial efforts have been made to examine the effect of bromide concentration on the formation and speciation of halogenated DBPs, almost all previous studies have focused on trihalomethanes and haloacetic acids. Given that about 50% of total organic halogen formed in chlorination remains unknown, it is still unclear how bromide concentration affects the formation and speciation of the new/unknown halogenated DBPs. In this study, chlorinated drinking water samples with different bromide concentrations were prepared, and a novel approach-precursor ion scan using ultra performance liquid chromatography/electrospray ionization-triple quadrupole mass spectrometry-was adopted for the detection and identification of polar halogenated DBPs in these water samples. With this approach, 11 new putative aromatic halogenated DBPs were identified, and they were classified into four groups: dihalo-4-hydroxybenzaldehydes, dihalo-4-hydroxybenzoic acids, dihalo-salicylic acids, and trihalo-phenols. A mechanism for the formation of the four groups of new aromatic halogenated DBPs was proposed. It was found that increasing the bromide concentration shifted the entire polar halogenated DBPs as well as the four groups of new DBPs from being less brominated to being more brominated; these new aromatic halogenated DBPs might be important intermediate DBPs formed in drinking water chlorination. Moreover, the speciation of the four groups of new DBPs was modeled: the speciation patterns of the four groups of new DBPs well matched those determined from the model equations, and the reactivity differences between HOBr and HOCl in reactions forming the four groups of new DBPs were larger than those in reactions forming trihalomethanes and haloacetic acids.

Natural Oxidation of Bromide to Bromine in Evaporated Dead Sea Brines

NASA Astrophysics Data System (ADS)

Gavrieli, Ittai; Golan, Rotem; Lazar, Boaz; Baer, Gidi; Zakon, Yevgeni; Ganor, Jiwchar

2016-04-01

Highly evaporated Dead Sea brines are found in isolated sinkholes along the Dead Sea. Many of these brines reach densities of over 1.3 kg/L and pH<5 and are the product of evaporation of Dead Sea brine that drain into the sinkholes. The low pH and the reddish to brownish hue of these brines were an enigma until recently. Despite the rather high total alkalinity (TA) of the Dead Sea (3.826 mmol/kg) the pH of the Dead Sea brine is known to be slightly acidic with a value of ~6.3. In comparison, seawater with the same alkalinity would have a pH value well above 8.3, meaning that H+ activity is 100 fold lower than that of Dead Sea brine. In the present work we assess the apparent dissociation constant value of boric acid (K`B) for the Dead Sea brine and use it to explain the brine's low pH value. We then show that pH decreases further as the brine evaporates and salinity increases. Finally we explain the reddish hue of the hypersaline brines in the sinkholes as due to the presence of dissolved bromine. The latter is the product of oxidation of dissolved bromide, a process that is enabled by the low pH of the hypersaline brines and their high bromide concentration.

Temperature dependence of chloride, bromide, iodide, thiocyanate and salicylate transport in human red cells

PubMed Central

Dalmark, Mads; Wieth, Jens Otto

1972-01-01

1. The temperature dependence of the steady-state self-exchange of chloride between human red cells and a plasma-like electrolyte medium has been studied by measuring the rate of 36Cl- efflux from radioactively labelled cells. Between 0 and 10° C the rate increased by a factor of eight corresponding to an Arrhenius activation energy of 33 kcal/mole. 2. The rate of chloride exchange decreased significantly in experiments where 95% of the chloride ions in cells and medium were replaced by other monovalent anions of a lyotropic series. The rate of chloride self-exchange was increasingly reduced by bromide, bicarbonate, nitrate, iodide, thiocyanate, and salicylate. The latter aromatic anion was by far the most potent inhibitor, reducing the rate of chloride self-exchange to 0·2% of the value found in a chloride medium. 3. The temperature sensitivity of the chloride self-exchange was not affected significantly by the anionic inhibitors. The Arrhenius activation energies of chloride exchange were between 30 and 40 kcal/mole in the presence of the six inhibitory anions mentioned above. 4. The rate of self-exchange of bromide, thiocyanate, and iodide between human red cells and media was determined after washing and labelling cells in media containing 120 mM bromide, thiocyanate, or iodide respectively. The rate of self-exchange of the three anions were 12, 3, and 0·4% of the rate of chloride self-exchange found in the chloride medium. 5. The Arrhenius activation energies of the self-exchange of bromide, iodide, and thiocyanate were all between 29 and 37 kcal/mole, the same magnitude as found for the self-exchange of chloride. 6. Although approximately 40% of the intracellular iodide and salicylate ions appeared to be adsorbed to intracellular proteins, the rate of tracer anion efflux followed first order kinetics until at least 98% of the intracellular anions had been exchanged. 7. The self-exchange of salicylate across the human red cell membrane occurred by a

77 FR 48153 - Protection of Stratospheric Ozone: Request for Methyl Bromide Critical Use Exemption Applications...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-13

... ENVIRONMENTAL PROTECTION AGENCY [EPA-HQ-OAR-2012-0375, FRL-9715-7] Protection of Stratospheric Ozone: Request for Methyl Bromide Critical Use Exemption Applications for 2015, Deadline Extension... Stratospheric Ozone Information Hotline, 1-800-296-1996; also http://www.epa.gov/ozone/mbr . Technical...

Re-manufacture of cobalt-manganese-bromide as a liquid catalyst from spent catalyst containing cobalt generated from petrochemical processes via hydrometallurgy.

PubMed

Joo, Sung-Ho; Shin, Dong Ju; Oh, Chang Hyun; Wang, Jei-Pil; Shin, Shun Myung

2016-11-15

Cobalt and manganese have been the subject of individual separation studies because their fields of application are different. However, this study shows that high-value products can be manufactured in the form of a cobalt-manganese-bromide (CMB) liquid catalyst by simultaneously recovering cobalt and manganese. Na-bis-(2,4,4-tri-methyl-pentyl)phosphinic acid was employed in order to manufacture the CMB liquid catalyst from the spent catalyst generated from petroleum chemistry processes. The pH-isotherm, degree of saponification of solvent and separation factor values were investigated. ΔpH50 and separation factor values show that Co and Mn can be separated from impurities such as Mg and Ca. Further, the extraction stages and organic/aqueous ratio isotherms were investigated using counter-current simulation extraction batch tests. To prepare CMB from a loaded organic phase obtained in a stripping study using hydrogen bromide, the Co and Mn were completely stripped and concentrated by a factor of 6 using a 2M hydrogen bromide solution. When compared with manufactured and commercial CMB, the CMB liquid catalyst could be produced by supplying a shortage of Mn in the form of manganese bromide. Finally, the method of manufacture of CMB was subjected to a real pilot plant test. Copyright © 2016. Published by Elsevier B.V.

Characterization of Stress in Thallium Bromide Devices

NASA Astrophysics Data System (ADS)

Datta, Amlan; Motakef, Shariar

2015-04-01

Thallium bromide (TlBr) is a wide bandgap, compound semiconductor with high gamma-ray stopping power and promising physical properties. Several surface modification techniques have been demonstrated to increase the lifetime of TlBr devices at room temperature. However, absence of reproducibility in the performance of TlBr detectors (even with low ionic conduction at -20°C) suggests presence of unexplored bulk phenomena. Stress in the TlBr crystal due to various intrinsic (e.g. grain boundaries and dislocations networks) in conjunction with external factors such as thermal, mechanical, and electrical loadings explains detector-to-detector variations. Photoelasticity and opto-electrical techniques were applied to visualize and qualitatively correlate the device performance with stress. Changes in stress patterns with variations in ambient temperature were clearly demonstrated. Electric field fluctuations in TlBr detectors with time were for the first time observed using the Pockels effect.

Cathode Degradation in Thallium Bromide Devices

NASA Astrophysics Data System (ADS)

Datta, Amlan; Motakef, Shariar

2015-06-01

Thallium bromide (TlBr) is a wide bandgap, compound semiconductor with high gamma-ray stopping power and promising physical properties. However, performance degradation and the eventual irreversible failure of TlBr devices can occur rapidly at room temperature, due to “polarization”, caused by the electromigration of Tl+ and Br- ions to the electrical contacts across the device. Using the Accelerated Device Degradation (ADD) experiment, the degradation phenomena in TlBr devices have been visualized and recorded. This paper focuses on “ageing” of the device cathode at various temperatures. ADD is a fast and reliable direct characterization technique that can be used to identify the effects of various growth and post-growth process modifications on device degradation. Using this technique we have identified cathode degradation with the migration of Br- ions and an associated generation and growth of Thallium-rich fractal “ferns” from the cathode. Its effect on the radiation response of the device has also been discussed in this paper. The chemical changes in the cathode were characterized using Energy-dispersive X-ray spectroscopy.

Comparative mobility of sulfonamides and bromide tracer in three soils

USGS Publications Warehouse

Kurwadkar, S.T.; Adams, C.D.; Meyer, M.T.; Kolpin, D.W.

2011-01-01

In animal agriculture, sulfonamides are one of the routinely used groups of antimicrobials for therapeutic and sub-therapeutic purposes. It is observed that, the animals when administered the antimicrobials, often do not completely metabolize them; and excrete the partially metabolized forms into the environment. Due to the continued use of antimicrobials and disposal of untreated waste, widespread occurrence of partially metabolized antimicrobials in aquatic and terrestrial environments has been reported in various scientific journals. In this research, the mobility of two sulfonamides - sulfamethazine (SMN), sulfathiazole (STZ) and a conservative bromide tracer was investigated in three soils collected from regions in the United States with large number of concentrated animal-feed operations. Results of a series of column studies indicate that the mobility of these two sulfonamides was dependent on pH, soil charge density, and contact time. At low pH and high charge density, substantial retention of sulfonamides was observed in all three soils investigated, due to the increased fraction of cationic and neutral forms of the sulfonamides. Conversely, enhanced mobility was observed at high pH, where the sulfonamides are predominantly in the anionic form. The results indicate that when both SMN and STZ are predominantly in anionic forms, their mobility approximates the mobility of a conservative bromide tracer. This observation is consistent for the mobility of both SMN and STZ individually, and also in the presence of several other antimicrobials in all three soils investigated. Higher contact time indicates lower mobility due to increased interaction with soil material. ?? 2011.

Thermal Decomposition Mechanism of 1-ethyl-3-methylimidazolium Bromide Ionic Liquid (Preprint)

DTIC Science & Technology

2011-09-14

TetraethylammoniumTrifluoromentanesulfonate Ionic Liquid and Neutralized Nafion 117 for High-Temperature Fuel Cells J. Am. Chem. Soc. 2010, 132, 2183-2195. (7) Kim, S. Y.; Kim, S...bromide 5b. GRANT NUMBER ionic liquid (Preprint) 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Steven D. Chambreau, Jerry A. Boatz, Ghanshyam L. Vaaghjiani...In order to better understand the volatilization process for ionic liquids , the vapor evolved from heating the ionic liquid 1-ethyl-3

Emission characteristics of plasma based on xenon-rubidium bromide mixture

NASA Astrophysics Data System (ADS)

Heneral, A. A.; Avtaeva, S. V.

2017-10-01

Luminescence spectra of a longitudinal pulse-periodic discharge in xenon mixture with rubidium bromide vapors (Xe-RbBr) are studied experimentally at low pressures. The conditions leading to the appearance of intense bands of ultraviolet radiation of exciplex XeBr* molecules in the spectral interval between 200 and 400 nm are found. The highest yield of UV radiation of XeBr* molecules is achieved when the temperature of discharge-tube walls is equal to 750°C. A maximum power of UV radiation from the entire plasma volume as high as 4.8 W is obtained.

Impact of Wildfire Emissions on Chloride and Bromide Depletion in Marine Aerosol Particles.

PubMed

Braun, Rachel A; Dadashazar, Hossein; MacDonald, Alexander B; Aldhaif, Abdulamonam M; Maudlin, Lindsay C; Crosbie, Ewan; Aghdam, Mojtaba Azadi; Hossein Mardi, Ali; Sorooshian, Armin

2017-08-15

This work examines particulate chloride (Cl - ) and bromide (Br - ) depletion in marine aerosol particles influenced by wildfires at a coastal California site in the summers of 2013 and 2016. Chloride exhibited a dominant coarse mode due to sea salt influence, with substantially diminished concentrations during fire periods as compared to nonfire periods. Bromide exhibited a peak in the submicrometer range during fire and nonfire periods, with an additional supermicrometer peak in the latter periods. Chloride and Br - depletions were enhanced during fire periods as compared to nonfire periods. The highest observed %Cl - depletion occurred in the submicrometer range, with maximum values of 98.9% (0.32-0.56 μm) and 85.6% (0.56-1 μm) during fire and nonfire periods, respectively. The highest %Br - depletion occurred in the supermicrometer range during fire and nonfire periods with peak depletion between 1.8-3.2 μm (78.8% and 58.6%, respectively). When accounting for the neutralization of sulfate by ammonium, organic acid particles showed the greatest influence on Cl - depletion in the submicrometer range. These results have implications for aerosol hygroscopicity and radiative forcing in areas with wildfire influence owing to depletion effects on composition.

Prolonged release matrix tablet of pyridostigmine bromide: formulation and optimization using statistical methods.

PubMed

Bolourchian, Noushin; Rangchian, Maryam; Foroutan, Seyed Mohsen

2012-07-01

The aim of this study was to design and optimize a prolonged release matrix formulation of pyridostigmine bromide, an effective drug in myasthenia gravis and poisoning with nerve gas, using hydrophilic - hydrophobic polymers via D-optimal experimental design. HPMC and carnauba wax as retarding agents as well as tricalcium phosphate were used in matrix formulation and considered as independent variables. Tablets were prepared by wet granulation technique and the percentage of drug released at 1 (Y(1)), 4 (Y(2)) and 8 (Y(3)) hours were considered as dependent variables (responses) in this investigation. These experimental responses were best fitted for the cubic, cubic and linear models, respectively. The optimal formulation obtained in this study, consisted of 12.8 % HPMC, 24.4 % carnauba wax and 26.7 % tricalcium phosphate, had a suitable prolonged release behavior followed by Higuchi model in which observed and predicted values were very close. The study revealed that D-optimal design could facilitate the optimization of prolonged release matrix tablet containing pyridostigmine bromide. Accelerated stability studies confirmed that the optimized formulation remains unchanged after exposing in stability conditions for six months.

Minimization of corrosion using activated sodium bromide in a medium-size cooling tower

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nalepa, C.J.; Moore, R.M.; Golson, G.L.

1996-07-01

The cooling tower at the Albermarle Process Development Center in Baton Rouge, Louisiana, historically used chlorine as a biocide in combination with phosphorus-based corrosion/scale inhibitors. Although this regimen provided biocontrol, sludge and iron buildup was a problem in low-velocity, small cross-sectional areas of piping. A general cleanup of the system was performed in April 1995. This cleanup was followed with a switch to a two-component corrosion inhibitor/dispersant package. Alternate biocides were evaluated at this time. Activated sodium bromide was found to be particularly effective in this tower, which operates at pH {approximately}8.4. Relative to chlorine, the use of activated sodiummore » bromide led to a decrease in general and pitting corrosion on mild steel. The reduced corrosion appears to be due to a combination of both chemical (less attack on passivated metal surfaces) and biological factors (better control of heterotrophic and sessile bacteria). These conclusions are supported by chemical analyses, corrosion meter and coupon data, dip slides, biological activity reaction tests, and visual observations of the tower sump and heat exchanger surfaces.« less

OZONATION BYPRODUCTS: IDENTIFICATION OF BROMOHYDRINS FROM THE OZONATION OF NATURAL WATERS WITH ENHANCED BROMIDE LEVELS

EPA Science Inventory

When ozone is used in the treatment of drinking water, it reacts with both inorganic and organic compounds to form byproducts. f bromide is present, it may be oxidized to hydrobromous acid, which may than react with natural organic matter to form brominated organic compounds. he ...

75 FR 41177 - Protection of Stratospheric Ozone: Request for Methyl Bromide Critical Use Exemption Applications...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-15

... this will be the state's agriculture or environmental protection agency) to receive information about.... Government (through EPA, Department of State, U.S. Department of Agriculture, and other interested Federal... baseline year, the U.S. consumption was approximately 25,500 metric tons of methyl bromide. In 2010, the...

A reconnaissance analysis of groundwater quality in the Eagle Ford shale region reveals two distinct bromide/chloride populations.

PubMed

Hildenbrand, Zacariah L; Carlton, Doug D; Meik, Jesse M; Taylor, Josh T; Fontenot, Brian E; Walton, Jayme L; Henderson, Drew; Thacker, Jonathan B; Korlie, Stephanie; Whyte, Colin J; Hudak, Paul F; Schug, Kevin A

2017-01-01

The extraction of oil and natural gas from unconventional shale formations has prompted a series of investigations to examine the quality of the groundwater in the overlying aquifers. Here we present a reconnaissance analysis of groundwater quality in the Eagle Ford region of southern Texas. These data reveal two distinct sample populations that are differentiable by bromide/chloride ratios. Elevated levels of fluoride, nitrate, sulfate, various metal ions, and the detection of exotic volatile organic compounds highlight a high bromide group of samples, which is geographically clustered, while encompassing multiple hydrogeological strata. Samples with bromide/chloride ratios representative of connate water displayed elevated levels of total organic carbon, while revealing the detection of alcohols and chlorinated compounds. These findings suggest that groundwater quality in the Western Gulf Basin is, for the most part, controlled by a series of natural processes; however, there is also evidence of episodic contamination events potentially attributed to unconventional oil and gas development or other anthropogenic activities. Collectively, this characterization of natural groundwater constituents and exogenous compounds will guide targeted remediation efforts and provides insight for agricultural entities, industrial operators, and rural communities that rely on groundwater in southern Texas. Copyright © 2016 Elsevier B.V. All rights reserved.

TRIBROMOPYRROLE, BROMINATED ACIDS, AND OTHER DISINFECTION BYPRODUCTS PRODUCED BY DISINFECTION OF DRINKING WATER RICH IN BROMIDE

EPA Science Inventory

Using gas chromatography/mass spectrometry (GC/MS), we investigated the formation of disinfection byproducts (DBPs) from high bromide waters (2 mg/L) treated with chlorine or chlorine dioxide used in combination with chlorine and chloramines. This study represents the first comp...

Copper(I)-catalyzed aryl bromides to form intermolecular and intramolecular carbon-oxygen bonds.

PubMed

Niu, Jiajia; Guo, Pengran; Kang, Juntao; Li, Zhigang; Xu, Jingwei; Hu, Shaojing

2009-07-17

A highly efficient Cu-catalyzed C-O bond-forming reaction of alcohol and aryl bromides has been developed. This transformation was realized through the use of copper(I) iodide as a catalyst, 8-hydroxyquinoline as a ligand, and K(3)PO(4) as a base. A variety of functionalized substrates were found to react under these reaction conditions to provide products in good to excellent yields.

Chloride, bromide and iodide scintillators with europium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhuravleva, Mariya; Yang, Kan

A halide scintillator material is disclosed where the halide may comprise chloride, bromide or iodide. The material is single-crystalline and has a composition of the general formula ABX.sub.3 where A is an alkali, B is an alkali earth and X is a halide which general composition was investigated. In particular, crystals of the formula ACa.sub.1-yEu.sub.yI.sub.3 where A=K, Rb and Cs were formed as well as crystals of the formula CsA.sub.1-yEu.sub.yX.sub.3 (where A=Ca, Sr, Ba, or a combination thereof and X=Cl, Br or I or a combination thereof) with divalent Europium doping where 0.ltoreq.y.ltoreq.1, and more particularly Eu doping has beenmore » studied at one to ten mol %. The disclosed scintillator materials are suitable for making scintillation detectors used in applications such as medical imaging and homeland security.« less

78 FR 36507 - Notice of Availability of a Treatment Evaluation Document; Methyl Bromide Fumigation of Blueberries

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-18

...] Notice of Availability of a Treatment Evaluation Document; Methyl Bromide Fumigation of Blueberries... blueberries for Mediterranean fruit fly and South American fruit fly. We have prepared a treatment evaluation... at neutralizing these fruit flies. We are making the treatment evaluation document available to the...

Adsorption Isotherm Studies of Methyl Bromide on MgO

NASA Astrophysics Data System (ADS)

Burns, Teresa; Larese, John

2003-11-01

The adsorption of methyl bromine onto highly-uniform magnesium oxide powder was studied using a high-precision computer-controlled gas adsorption system. Methyl bromide was condensed onto the MgO substrate at temperatures between 165 K and 180 K. The layering behavior, iosthermal compressibility, and isosteric heat of adsorption were determined. Isotherms will be presented and future work discussed. TEB research sponsored by the Department of Energy EPSCOR Grant No. DE-FG02-01ER45895. JZL research sponsored by start-up funds from the University of Tennessee - Knoxville and by the Division of Materials Sciences, Office of Basic Energy Sciences, U.S. Department of Energy, under contract No. DE-AC05-00OR22725 with Oak Ridge National Laboratory, managed and operated by UT-Battelle, LLC.

Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Horizontal Stacks, 8 Hours or Less

EPA Pesticide Factsheets

This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, No Stack, More than 8 Hours

EPA Pesticide Factsheets

This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, No Stack, 8 Hours or Less

EPA Pesticide Factsheets

This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

40 CFR 721.10115 - 1-Hexadecanaminium, N,N-dibutyl-N-(2-hydroxyethyl)-, bromide (1:1).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false 1-Hexadecanaminium, N,N-dibutyl-N-(2... New Uses for Specific Chemical Substances § 721.10115 1-Hexadecanaminium, N,N-dibutyl-N-(2... chemical substance identified as 1-hexadecanaminium, N,N-dibutyl-N-(2-hydroxyethyl)-, bromide (1:1) (PMN P...

40 CFR 721.10115 - 1-Hexadecanaminium, N,N-dibutyl-N-(2-hydroxyethyl)-, bromide (1:1).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false 1-Hexadecanaminium, N,N-dibutyl-N-(2... New Uses for Specific Chemical Substances § 721.10115 1-Hexadecanaminium, N,N-dibutyl-N-(2... chemical substance identified as 1-hexadecanaminium, N,N-dibutyl-N-(2-hydroxyethyl)-, bromide (1:1) (PMN P...

Metal cluster's effect on the optical properties of cesium bromide thin films

NASA Astrophysics Data System (ADS)

Kumar, Kuldeep; Arun, P.; Ravi Kant, Chhaya; Juluri, Bala Krishna

2012-06-01

Cesium bromide (CsBr) films grown on glass substrates by thermal evaporation showed prominent absorption peaks in the UV-visible region. Interestingly, these absorption spectra showed peaks which red shifted over time in ambient exposure. Structural and morphological studies suggested decrease in particle size overtime which was unusual. Electron micrographs show the formation of "daughter" cesium nanorods from parent CsBr particles. Theoretical calculations show the optical behavior observed to be due to localized surface plasmon resonance resulting from cesium nanorods.

Phytoremediation potentials of selected tropical plants for ethidium bromide.

PubMed

Uera, Raynato B; Paz-Alberto, Annie Melinda; Sigua, Gilbert C

2007-11-01

Research and development has its own benefits and inconveniences. One of the inconveniences is the generation of enormous quantity of diverse toxic and hazardous wastes and its eventual contamination to soil and groundwater resources. Ethidium bromide (EtBr) is one of the commonly used substances in molecular biology experiments. It is highly mutagenic and moderately toxic substance used in DNA-staining during electrophoresis. Interest in phytoremediation as a method to solve chemical contamination has been growing rapidly in recent years. The technology has been utilized to clean up soil and groundwater from heavy metals and other toxic organic compounds in many countries like the United States, Russia, and most of European countries. Phytoremediation requires somewhat limited resources and very useful in treating wide variety of environmental contaminants. This study aimed to assess the potential of selected tropical plants as phytoremediators of EtBr. This study used tomato (Solanum lycopersicum), mustard (Brassica alba), vetivergrass (Vetiveria zizanioedes), cogongrass (Imperata cylindrica), carabaograss (Paspalum conjugatum), and talahib (Saccharum spontaneum) to remove EtBr from laboratory wastes. The six tropical plants were planted in individual plastic bags containing soil and 10% EtBr-stained agarose gel. The plants were allowed to establish and grow in soil for 30 days. Ethidium bromide content of the test plants and the soil were analyzed before and after soil treatment. Ethidium bromide contents of the plants and soils were analyzed using an UV VIS spectrophotometer. Results showed a highly significant (p< or =0.001) difference in the ability of the tropical plants to absorb EtBr from soils. Mustard registered the highest absorption of EtBr (1.4+/-0.12 microg kg(-1)) followed by tomato and vetivergrass with average uptake of 1.0+/-0.23 and 0.7+/-0.17 microg kg(-1) EtBr, respectively. Cogongrass, talahib, and carabaograss had the least amount of Et

Estimating Potential Increased Bladder Cancer Risk Due to Increased Bromide Concentrations in Sources of Disinfected Drinking Waters

EPA Science Inventory

Public water systems are increasingly facing higher bromide levels in their source waters from anthropogenic contamination through coal-fired power plants, conventional oil and gas extraction, and hydraulic fracturing. Climate change is likely to exacerbate this in coming years. ...

Efficient Sky-Blue Perovskite Light-Emitting Devices Based on Ethylammonium Bromide Induced Layered Perovskites.

PubMed

Wang, Qi; Ren, Jie; Peng, Xue-Feng; Ji, Xia-Xia; Yang, Xiao-Hui

2017-09-06

Low-dimensional organometallic halide perovskites are actively studied for the light-emitting applications due to their properties such as solution processability, high luminescence quantum yield, large exciton binding energy, and tunable band gap. Introduction of large-group ammonium halides not only serves as a convenient and versatile method to obtain layered perovskites but also allows the exploitation of the energy-funneling process to achieve a high-efficiency light emission. Herein, we investigate the influence of the addition of ethylammonium bromide on the morphology, crystallite structure, and optical properties of the resultant perovskite materials and report that the phase transition from bulk to layered perovskite occurs in the presence of excess ethylammonium bromide. On the basis of this strategy, we report green perovskite light-emitting devices with the maximum external quantum efficiency of ca. 3% and power efficiency of 9.3 lm/W. Notably, blue layered perovskite light-emitting devices with the Commission Internationale de I'Eclairage coordinates of (0.16, 0.23) exhibit the maximum external quantum efficiency of 2.6% and power efficiency of 1 lm/W at 100 cd/m 2 , representing a large improvement over the previously reported analogous devices.

Identification of a BrOOO- intermediate species in the ozonolysis of bromide at the liquid/vapor interface from liquid jet XPS

NASA Astrophysics Data System (ADS)

Chen, Shuzhen; Artiglia, Luca; Orlando, Fabrizio; Corral-Arroyo, Pablo; Edebeli, Jacinta; Ammann, Markus

2017-04-01

Oxidation of bromide by gas phase ozone (O3) in the absence of photochemistry is believed to be one of the important dark reactions to produce HOBr as the starting point of the multiphase cycling reaction mechanisms that release bromide out of sea water, sea spray or marine aerosols from aqueous solution that later drive O3 depleting chemistry in the troposphere [1]. The reaction of bromide with O3 occurs through an acid catalyzed mechanism involving a BrOOO- complex as an intermediate [2]. Slow oxidation of bromide by O3 in the bulk aqueous phase is of limited relevance; previous kinetic experiments have suspected the reaction to be enhanced at the surface of aqueous solutions. Thus, identifying BrOOO- at the interface would be a major step to understanding the multiphase oxidation of bromide with O3. Here, we provide a direct experimental evidence for the formation of a BrOOO- reaction intermediate at the surface by investigating the reaction of aqueous solutions NaBr with gas phase O3 after millisecond time scale exposure using the surface sensitive in situ liquid jet X-ray photoelectron spectroscopy (XPS) at the Swiss Light Source (SLS). We acquired Br 3d core level spectra of 0.125 M NaBr solution in presence and absence of ozone in the gas phase. We found a new feature with a peak position shifted towards higher binding energy (by ˜0.7 eV) compared to Br-, which was clearly different from the Br 3d core levels spectra of hypobromite and bromate measured with reference solutions. Our results suggest the appearance of the formation of the BrOOO- reaction intermediate as a new component, in agreement with theoretical calculations of the Br- ozonolysis mechanism [3]. Additionally, by varying the photoelectron kinetic energy and thus probe depth via variation of the probing photon energy, the new feature appears to be present near the liquid/vapor interface. Besides, kinetic experiments for the reaction of O3 with bromide are ongoing to investigate the dependence

Integration of Bromine and Cyanogen Bromide Generators for the Continuous-Flow Synthesis of Cyclic Guanidines.

PubMed

Glotz, Gabriel; Lebl, René; Dallinger, Doris; Kappe, C Oliver

2017-10-23

A continuous-flow process for the in situ on-demand generation of cyanogen bromide (BrCN) from bromine and potassium cyanide that makes use of membrane-separation technology is described. In order to circumvent the handling, storage, and transportation of elemental bromine, a continuous bromine generator using bromate-bromide synproportionation can optionally be attached upstream. Monitoring and quantification of BrCN generation was enabled through the implementation of in-line FTIR technology. With the Br 2 and BrCN generators connected in series, 0.2 mmol BrCN per minute was produced, which corresponds to a 0.8 m solution of BrCN in dichloromethane. The modular Br 2 /BrCN generator was employed for the synthesis of a diverse set of biologically relevant five- and six-membered cyclic amidines and guanidines. The set-up can either be operated in a fully integrated continuous format or, where reactive crystallization is beneficial, in semi-batch mode. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

76 FR 7200 - Methyl Bromide; Notice of Receipt of Requests To Voluntarily Amend Registrations To Terminate...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-09

... Receipt of Requests To Voluntarily Amend Registrations To Terminate Certain Soil Uses AGENCY... terminate or delete one or more soil uses. The requests would delete all methyl bromide soil uses that do... application'' with the exception of the following uses: (1) Soils to be planted with caneberries (use allowed...

Laboratory Evaluation of Drop-in Solvent Alternatives to n-Propyl Bromide for Vapor Degreasing

NASA Technical Reports Server (NTRS)

Mitchell, Mark A.; Lowrey, Nikki M.

2012-01-01

Based on this limited laboratory study, solvent blends of trans-1,2 dichloroethylene with HFEs, HFCs, or PFCs appear to be viable alternatives to n-propyl bromide for vapor degreasing. The lower boiling points of these blends may lead to greater solvent loss during use. Additional factors must be considered when selecting a solvent substitute, including stability over time, VOC, GWP, toxicity, and business considerations.

Charge carrier transport properties in thallium bromide crystalls used as radiation detectors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Olschner, F.; Toledo-Quinones, M.; Shah, K.S.

1990-06-01

Thallium bromide (TlBr) is an attractive material for use in radiation detectors because of its wide bandgap (2.68 eV) and very high atomic number. Usefulness as a semiconductor detector material, however, also requires good charge carrier transport properties in order to maximize the magnitude of the signal from the detector. The authors report on measurements of the two most important transport parameters; the mobility {mu} and the mean trapping time {tau} for electrons and holes in TlBr crystals prepared in the laboratory.

Recent Progress in Thallium Bromide Gamma-Ray Spectrometer Development

NASA Astrophysics Data System (ADS)

Kim, Hadong; Kargar, Alireza; Cirignano, Leonard; Churilov, Alexei; Ciampi, Guido; Higgins, William; Olschner, Fred; Shah, Kanai

2012-02-01

In recent years, progress in processing and crystal growth methods have led to a significant increase in the mobility-lifetime product of electrons in thallium bromide (TlBr). This has enabled single carrier collection devices with thickness greater than 1-cm to be fabricated. In this paper we report on our latest results from pixellated devices with depth correction as well as our initial results with Frisch collar devices. After applying depth corrections, energy resolution of approximately 2% (FWHM at 662 keV) was obtained from a 13-mm thick TlBr array operated at -18°C and under continuous bias and irradiation for more than one month. Energy resolution of 2.4% was obtained at room temperature with an 8.4-mm thick TlBr Frisch collar device.

Interaction between dimethyldioctadecylammonium bromide-modified PLGA microspheres and hyaluronic acid

NASA Astrophysics Data System (ADS)

Mulia, Kamarza; Devi, Krisanti, Elsa

2017-02-01

In application of intravitreal injection, an extended drug delivery system is desired so that the frequency of injection to treat diabetic retinopathy may be reduced. Poly(lactic-co-glycolic acid) polymer (PLGA) was used to encapsulate a model drug in the form of microspheres. The zeta potential of dimethyldioctadecylammonium bromide (DDAB)-modified PLGA microspheres in water was proportional to the DDAB concentration used in the preparation step, up to +57.8 mV. The scanning electron microscope pictures and the zeta potential data (SEM) confirmed that the surface of the PLGA has been modified by the cationic surfactant and that electrostatic interaction between the positively charged microspheres and the negatively charged vitreous were present.

Introducing the New Class of N-Phosphoryl Ynamides via Cu(I)-Catalyzed Amidations of Alkynyl Bromides

PubMed Central

Walton, Mary C.; North, Troy D.

2011-01-01

We describe here the first synthesis of N-phosphoryl ynamides featuring C- and P-chirality via copper(I)-catalyzed amidative cross-couplings between phosphoramidates and phosphordiamidates with alkynyl bromides. Also featured is a tandem aza-Claisen–hetero-[2+2] cycloaddition for the synthesis of N-phosphoryl azetidin-2-imines. PMID:21848304

Evaluation of the mydriatic effects of topical administration of rocuronium bromide in Hispaniolan Amazon parrots (Amazona ventralis).

PubMed

Petritz, Olivia A; Guzman, David Sanchez-Migallon; Gustavsen, Kate; Wiggans, K Tomo; Kass, Philip H; Houck, Emma; Murphy, Christopher J; Paul-Murphy, Joanne

2016-01-01

OBJECTIVE :To determine the mydriatic effects of topical rocuronium bromide administration in Hispaniolan Amazon parrots (Amazona ventralis) and to identify any adverse effects associated with treatment. Randomized crossover study. 8 healthy adult Hispaniolan Amazon parrots. Rocuronium bromide (20 μL/eye; 10 mg/mL) or saline (20 μL/eye; 0.9% NaCl) solution was administered in both eyes of each bird with a 26-day washout period. The birds were manually restrained in lateral recumbency with the apex of the cornea positioned upward for 2 minutes following administration in each eye. Infrared pupillometry and direct pupillary light reflex measurements were used to evaluate the mydriatic effects. Pupillary measurements were recorded prior to administration and every 20 minutes for 2 hours after administration, then hourly for a total of 7 hours. A brief physical examination was performed, direct pupillary light reflex was tested, and fluorescein staining was performed on each eye of each bird 24 hours after administration. A significant difference in pupillary diameter for the active versus control treatment group was noted from 20 to 360 minutes after drug administration, but not at 420 minutes. Minimal adverse effects were noted. Three birds had transient inferior eyelid paresis noted in both eyes after receiving rocuronium; 24 hours after the treatment, no differences in ocular measurements existed between the active and control treatments. Results suggested that topical rocuronium bromide administration may be safely used for pupillary dilation in Hispaniolan Amazon parrots and could be used for clinical evaluation, fundus imaging, and surgical interventions involving the lens and posterior segment in this species.

Ethidium bromide stimulated hyper laccase production from bird's nest fungus Cyathus bulleri.

PubMed

Dhawan, S; Lal, R; Kuhad, R C

2003-01-01

Effect of ethidium bromide, a DNA intercalating agent, on laccase production from Cyathus bulleri was studied. The bird's nest fungus, Cyathus bulleri was grown on 2% (w/v) malt extract agar (MEA) supplemented with 1.5 microg ml(-1) of the phenanthridine dye ethidium bromide (EtBr) for 7 d and when grown subsequently in malt extract broth (MEB), produced a 4.2-fold increase in laccase production as compared to the untreated fungus. The fungal cultures following a single EtBr treatment, when regrown on MEA devoid of EtBr, produced a sixfold increase in laccase in MEB. However, on subsequent culturing on MEA in the absence of EtBr, only a 2.5-fold increase in laccase production could be maintained. In another attempt, the initial EtBr-treated cultures, when subjected to a second EtBr treatment (1.5 microg ml(-1)) on MEA for 7 d, produced a 1.4-fold increase in laccase production in MEB. The white-rot fungus Cyathus bulleri, when treated with EtBr at a concentration of 1.5 microg ml(-1) and regrown on MEA devoid of EtBr, produced a sixfold increase in laccase production in MEB. The variable form of C. bulleri capable of hyper laccase production can improve the economic feasibility of environmentally benign processes involving use of fungal laccases in cosmetics (including hair dyes), food and beverages, clinical diagnostics, pulp and paper industry, industrial effluent treatment, animal biotechnology and biotransformations.

Estimating Potential Increased Bladder Cancer Risk Due to Increased Bromide Concentrations in Sources of Disinfected Drinking Waters - slides

EPA Science Inventory

Public water systems are increasingly facing higher bromide levels in their source waters from anthropogenic contamination through coal-fired powerplants, conventional oil and gas extraction, and hydraulic fracturing. Climate change is likely to exacerbate this in coming years. W...

Chloride, bromide and iodide scintillators with europium doping

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhuravleva, Mariya; Yang, Kan

A halide scintillator material is disclosed where the halide may comprise chloride, bromide or iodide. The material is single-crystalline and has a composition of the general formula ABX.sub.3 where A is an alkali, B is an alkali earth and X is a halide which general composition was investigated. In particular, crystals of the formula ACa.sub.1-yEu.sub.yI.sub.3 where A=K, Rb and Cs were formed as well as crystals of the formula CsA.sub.1-yEu.sub.yX.sub.3 (where A=Ca, Sr, Ba, or a combination thereof and X=Cl, Br or I or a combination thereof) with divalent Europium doping where 0.ltoreq.y.ltoreq.1, and more particularly Eu doping has beenmore » studied at one to ten mol %. The disclosed scintillator materials are suitable for making scintillation detectors used in applications such as medical imaging and homeland security.« less

Fabrication of double-sided thallium bromide strip detectors

NASA Astrophysics Data System (ADS)

Hitomi, Keitaro; Nagano, Nobumichi; Onodera, Toshiyuki; Kim, Seong-Yun; Ito, Tatsuya; Ishii, Keizo

2016-07-01

Double-sided strip detectors were fabricated from thallium bromide (TlBr) crystals grown by the traveling-molten zone method using zone-purified materials. The detectors had three 3.4-mm-long strips with 1-mm widths and a surrounding electrode placed orthogonally on opposite surfaces of the crystals at approximately 6.5×6.5 mm2 in area and 5 mm in thickness. Excellent charge transport properties for both electrons and holes were observed from the TlBr crystals. The mobility-lifetime products for electrons and holes in the detector were measured to be ~3×10-3 cm2/V and ~1×10-3 cm2/V, respectively. The 137Cs spectra corresponding to the gamma-ray interaction position were obtained from the detector. An energy resolution of 3.4% of full width at half maximum for 662-keV gamma rays was obtained from one "pixel" (an intersection of the strips) of the detector at room temperature.

Location of Bromide Ions in Tetragonal Lysozyme Crystals

NASA Technical Reports Server (NTRS)

Lim, Kap; Nadarajah, Arunan; Forsythe, Elizabeth L.; Pusey, Marc L.

1998-01-01

Anions have been shown to play a dominant role in the crystallization of chicken egg white lysozyme from salt solutions. Previous studies employing X-ray crystallography had found one chloride ion binding site in the tetragonal crystal form of the protein and four nitrate ion binding sites in the monoclinic form. In this study the anion positions in the tetragonal form were determined from the difference Fourier map obtained from lysozyme crystal grown in bromide and chloride solutions. Five possible anion binding sites were found in this manner. Some of these sites were in pockets containing basic residues while others were near neutral, but polar, residues. The sole chloride ion binding site found in previous studies was confirmed, while four of these sites corresponded to four binding sites found for nitrate ions in monoclinic crystals. The study suggests that most of the anion binding sites in lysozyme remain unchanged, even when different anions and different crystal forms of lysozyme are employed.

Locations of Bromide Ions in Tetragonal Lysozyme Crystals

NASA Technical Reports Server (NTRS)

Lim, Kap; Nadarajah, Arunan; Forsythe, Elizabeth L.; Pusey, Marc L.

1998-01-01

Anions have been shown to play a dominant role in the crystallization of chicken egg-white lysozyme from salt solutions. Previous studies employing X-ray crystallography have found one chloride ion binding site in the tetragonal crystal form of the protein and four nitrate ion binding sites in the monoclinic form. In this study the anion positions in the tetragonal form were determined from the difference Fourier map obtained from lysozyme crystals grown in bromide and chloride solutions. Five possible anion-binding sites were found in this manner. Some of these sites were in pockets containing basic residues while others were near neutral, but polar, residues. The sole chloride ion binding site found in previous studies was confirmed, while four further sites were found which corresponded to the four binding sites found for nitrate ions in monoclinic crystals. The study suggests that most of the anion-binding sites in lysozyme remain unchanged even when different anions and different crystal forms of lysozyme are employed.

Highly Reactive, General and Long-Lived Catalysts for Palladium-Catalyzed Amination of Heteroaryl and Aryl Chlorides, Bromides and Iodides: Scope and Structure-Activity Relationships

PubMed Central

Shen, Qilong; Ogata, Tokutaro; Hartwig, John F.

2010-01-01

We describe a systematic study of the scope and relationship between ligand structure and activity for a highly efficient and selective class of catalysts for the amination of heteroaryl and aryl chlorides, bromides and iodides containing sterically hindered chelating alkylphosphines. In the presence of this catalyst, aryl and heteroaryl chlorides, bromides and iodides react with many primary amines in high yields with part-per-million quantities of palladium precursor and ligand. Many reactions of primary amines with both heteroaryl and aryl chlorides, bromides and iodides occur to completion with 0.0005-0.05 mol % catalysts. A comparison of the reactivity of this catalyst for coupling of primary amines at these loadings is made with catalysts generated from hindered monophosphines and carbenes, and these data illustrate the benefits of chelation. Thus, these complexes constitute a fourth-generation catalyst for the amination of aryl halides, whose activity complements catalysts based on monophosphines and carbenes. PMID:18444639

Fumigation of Jute Bags with Ethylene Oxide and Methyl Bromide to Eradicate Potato Ring Rot Bacteria1

PubMed Central

Richardson, L. T.; Monro, H. A. U.

1962-01-01

In a series of full-scale tests, the effectiveness of various fumigant treatments for the eradication of potato ring rot bacteria from bulk lots of contaminated jute bags was evaluated. Survival of these bacteria on infested sample fibers located at various positions within and around a tightly wired bale was determined quantitatively from the growth lag in a liquid medium as indicated by the rate of turbidity development. Ethylene oxide, though highly toxic to Corynebacterium sepedonicum in laboratory tests, failed to penetrate the jute sufficiently to be effective in the interior of a bale. Methyl bromide showed better penetration, but was not sufficiently toxic at practical dosage levels. A mixture of 5% ethylene oxide and 10% methyl bromide achieved complete eradication throughout a bale in an 18-hr exposure period. On the basis of these results, eradication of ring rot bacteria from contaminated jute bags by fumigation with a combination of these two gases would appear to be feasible under commercial conditions. PMID:13982125

Scenario Analysis of the Impact on Drinking Water Intakes from Bromide in the Discharge of Treated Oil and Gas Wastewater

EPA Pesticide Factsheets

EPA scientists created different scenarios for conventional commercial wastewater treatment plants that treat oil and gas wastewaters to evaluate the impact from bromide in discharges by the CWTP plants.

[Efficacy of glycopyrronium bromide and scopolamine hydrobromide in patients with death rattle: a randomized controlled study].

PubMed

Likar, Rudolf; Rupacher, Ernst; Kager, Hans; Molnar, Mario; Pipam, Wofgang; Sittl, Reinhard

2008-01-01

Death rattle is an extremely distressing symptom for the dying patient and for his environment. The aim of this study was to assess the efficacy of glycopyrronium bromide as compared with scopolamine hydrobromide in alleviating death rattle in terminal cancer patients with cognitive impairment. In a randomized, controlled study design patients were allocated in two groups. Group A received scopolamine hydrobromide in a dose of 0.5 mg intravenously every 6 hours for a period of 12 hours, group B received glycopyrronium bromide 0.4 mg every 6 hours for a period of 12 hours. In addition, standardized sedatives were administered as required and the analgesic therapy continued either orally or, if necessary, subcutaneously or intravenously in equipotent doses. Every 2 hours death rattle was assessed and rated on a scale of 1 to 5 (1 = audible breathing noises, 5 = very severe rattling noises). In addition, restlessness and expressions of pain were assessed and rated on a scale of 1 to 3 (1 = mild, 2 = moderate, 3 = severe). 13 patients were included in the study, 7 patients were allocated to group A and 6 patients to group B. There were no significant differences in demographic data, age, weight and diagnosis distribution between the two groups. Group B demonstrated a significant reduction of death rattle in the first 12 hours (p = 0.029) in comparison to group A. There were no significant differences concerning the side effects (restlessness, expressions of pain) in both groups. Glycopyrronium bromide given in a dose of 0,4 mg every six hours demonstrated a significant reduction of death rattle compared to scopolamine hydrobromide. Concerning side effects (restlessness, expressions of pain) there was no difference between both substances.

Moving away from methyl bromide: political economy of pesticide transition for California strawberries since 2004.

PubMed

Mayfield, Erin N; Norman, Catherine Shelley

2012-09-15

We examine the progress of the phaseout of the use of the pesticide methyl bromide in the production of California field strawberries. This phaseout is required under the Montreal Protocol and has been contentious in this sector, which receives exemptions from the schedule initially agreed under the treaty, and in international negotiations over the future of the Protocol. We examine the various ex-ante predictions of the impacts on growers, consumers and trade patterns in light of several years of declining allocations under the Critical Use provisions of the Protocol and the 2010 approval of iodomethane for use in California and subsequent 2012 withdrawal of this alternative from the US market. We find that, contrary to ex-ante industry claims, the years of declining methyl bromide use have been years of rising yields, acreage, exports, revenues and market share for California growers, even when faced with a global recession and increased imports from Mexican growers who retain the right to use the chemical under the Protocol. This has implications for the Protocol as a whole and for the remainder of the US phaseout of this chemical in particular. Copyright © 2012 Elsevier Ltd. All rights reserved.

Crystal growth and scintillation properties of potassium strontium bromide

NASA Astrophysics Data System (ADS)

Stand, L.; Zhuravleva, M.; Wei, H.; Melcher, C. L.

2015-08-01

In this work, potassium strontium bromide activated with divalent europium, (KSr2Br5:Eu) has been studied. It has a monoclinic crystal structure and a density of 3.98 g/cm3. Two single crystals of KSr2Br5 doped with 5% Eu2+, with diameters of 13 mm and 22 mm, were grown in a two zone transparent furnace via the Bridgman technique. The X-ray excited emission spectrum consisted of a single peak at ∼427 nm due to the 5d-4f transition in Eu2+. The measured light yield and energy resolution at 662 keV was 75,000 ph/MeV and 3.5%. At low energies KSr2Br5:Eu 5% also displays good energy resolution, 6.7% at 122 keV and 7.9% at 59.5 keV.

Use of bromide:Chloride ratios to differentiate potential sources of chloride in a shallow, unconfined aquifer affected by brackish-water intrusion

USGS Publications Warehouse

Andreasen, D.C.; Fleck, W.B.

1997-01-01

Brackish water from Chesapeake Bay and its tributaries has entered the Aquia aquifer in east-central Anne Arundel County, Maryland, USA. This determination was made based on chloride analyses of water samples collected in wells screened in the Aquia aquifer between October 1988 and May 1989. The Aquia aquifer, which is composed of fine- to medium-grained sand, is a shallow, unconfined aquifer in this area. Land use is primarily urban, consisting of a mixture of residential and light commercial areas. Associated with the urban setting is the potential for chloride contamination to enter the Aquia aquifer from anthropogenic sources, such as residential septic-tank effluent, leaky public sewer lines, road-deicing salt, stormwater infiltration basins, and domestic water-conditioning recharge effluent. In order to map the distribution of bay-water intrusion in the Aquia aquifer, chloride derived from Chesapeake Bay was differentiated from chloride derived from anthropogenic sources by comparing the ratio of dissolved bromide to dissolved chloride (bromide:chloride) in groundwater to the distinctive ratio in Chesapeake Bay water. Two additional factors considered in determining the source of the chloride were nitrogen concentrations and well-screen positions of sampled wells in relation to the estimated depth of the fresh-water/brackish-water interface. Of 36 Aquia-aquifer water samples with chloride concentrations greater than 30 mg/L, 22 had bromide:chloride ratios similar to the ratio in Chesapeake Bay water, an indication that bay water is the primary source of the chloride. Of the other 14 samples with bromide:chloride ratios dissimilar to the ratio in Chesapeake Bay water, seven were from wells where screen positions were substantially above the estimated fresh-water/brackish-water interface. Three of these samples had nitrogen concentrations (as nitrite plus nitrate) greater than 3.0 mg/L, an indication that chloride in these groundwater samples comes from

Optimizing postharvest methyl bromide treatments to control spotted wing drosophila, Drosophila suzukii, in sweet cherries from Western USA

USDA-ARS?s Scientific Manuscript database

Methyl bromide (MB) chamber fumigations were evaluated for postharvest control of spotted wing drosophila (SWD), Drosophila suzukii (Matsumura) (Diptera: Drosophilidae), in fresh sweet cherry exports from Western USA. Sweet cherries were infested with SWD, incubated to maximize numbers of the most M...

Bromidotetra­kis­(2-isopropyl-1H-imidazole-κN 3)copper(II) bromide

PubMed Central

Godlewska, Sylwia; Socha, Joanna; Baranowska, Katarzyna; Dołęga, Anna

2011-01-01

The CuII atom in the title salt, [CuBr(C6H10N2)4]Br, is coordinated in a square-pyramidal geometry by four imidazole N atoms and one bromide anion that is located at the apex of the pyramid. The cations and the anions form a two-dimensional network parallel to (001) through N—H⋯Br hydrogen bonds. PMID:22064905

Self-made silver-bromide-based emulsions for users in holography: manufacturing, processing, and application

NASA Astrophysics Data System (ADS)

Duenkel, Lothar; Eichler, Juergen; Ackermann, Gerhard; Schneeweiss, Claudia

2004-06-01

Holography is the most fascinating technology for three-dimensional imaging. But despite of many decades of research, the seek for an ideal recording material has never been given up. From all ultra-fine materials, silver bromide emulsions with very small grain sizes have the highest sensitivity. In recent years however, many traditional manufacturers discontinued their production. Meanwhile, newcomers succeeded in manufacturing emulsions which are very suitable for holography, concerning extremely high resolution, brigthness and sensitivity1. But two problems may still linger: First, the deficient market situation for production and application on this field. Second, the reputation of the system of being extremely complicated for laboratory preparation. In such a crucial situation, the authors have succeeded in presenting a laboratory procedure for making do-it-yourself materials available to any expert who is well versed in holography, and who disposes of normal darkroom equipment2. The methodology is based on precipitation using the traditional double-jet method according to Thiry and predecessors3. But sensitization is carried out by a diffusion process according to the procedure as proposed by Blyth et al.4 Thus, precipitation and coating on one side and sensitization on the other one are separated strictly from one another. Efficient desaltation is an important process too, warranting the high opto-mechanical quality of the layer. The material has been sensitzed for HeNe-Laser radiation (632,8 nm) only up to now. The mean diameter of the silver bromide grains is about 15 nm, as determined by transmission electron microscopy (TEM). Phillips-Bjelkhagen Ultimate (PBU) or Fe3+ rehalogenation bleach are applied successfully5-6. In final result, a new generation of holograms with ultra-high resolution, proper contrast, excellent sharpness and light brightness has been obtained. Holography belongs to an advancing technology where the search for an ideal recording

Effect of phytosanitary irradiation and methyl bromide fumigation on the physical, sensory, and microbiological quality of blueberries and sweet cherries.

PubMed

Thang, Karen; Au, Kimberlee; Rakovski, Cyril; Prakash, Anuradha

2016-10-01

The objective of this study was to determine whether irradiation could serve as a suitable phytosanitary treatment alternative to methyl bromide (MB) fumigation for blueberries and sweet cherry and also to determine the effect of phytosanitary irradiation treatment on survival of Salmonella spp. and Listeria monocytogenes on these fruit. 'Bluecrop' blueberries (Vaccinium corymbosum) and 'Sweetheart' cherries (Prunus avium) were irradiated at 0.4 kGy or fumigated with methyl bromide and evaluated for quality attributes during storage. Irradiation caused an immediate decrease in firmness of both fruit without further significant change during storage. Fumigated fruit, in contrast, softened by 11-14% during storage. Irradiation did not adversely affect blueberry and cherry shelf-life. MB fumigation did not impact blueberry and cherry quality attributes initially; however, fumigated fruit exhibited greater damage and mold growth than the control and irradiated samples during storage. Irradiation at 400 Gy resulted in a ∼1 log CFU g(-1) reduction in Salmonella spp. and Listeria monocytogenes counts, indicating that this treatment cannot significantly enhance safety. This study indicates that irradiation at a target dose of 0.4 kGy for phytosanitary treatment does not negatively impact blueberry and cherry quality and can serve as an alternative to methyl bromide fumigation. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Simultaneous determination of pyridostigmine bromide, N,N-diethyl-m-toluamide, permethrin, and their metabolites in rat plasma and urine by high-performance liquid chromatography.

PubMed

Abu-Qare, A W; Abou-Donia, M B

2000-12-01

A rapid and simple method was developed for the separation and quantification of the anti nerve agent drug pyridostignmine bromide (PB; 3-dimethylaminocarbonyloxy-N-methyl pyridinium bromide) its metabolite N-methyl-3-hydroxypyridinium bromide, the insect repellent DEET (N,N-diethyl-m-toluamide), its metabolites m-toluamide and m-toluic acid, the insecticide permethrin (3-(2,2-dichloro-ethenyl)-2,2-dimethylcyclopropanecarboxylic acid(3-phenoxyphenyl)methylester), and two of its metabolites m-phenoxybenzyl alcohol, and m-phenoxybenzoic acid in rat plasma and urine. The method is based on using C18 Sep-Pak cartridges for solid-phase extraction (SPE) and high-performance liquid chromatography (HPLC) with reversed-phase C18 column, and gradient UV detection ranging between 208 and 230 nm. The compounds were separated using gradient of 1 to 99% acetonitrile in water (pH 3.20) at a flow-rate ranging between 0.5 and 1.7 ml/min in a period of 17 min. The retention times ranged from 5.7 to 14.5 min. The limits of detection were ranged between 20 and 100 ng/ml, while limits of quantitation were 150-200 ng/ml. Average percentage recovery of five spiked plasma samples were 51.4+/-10.6, 71.1+/-11.0, 82.3+/-6.7, 60.4+/-11.8, 63.6+/-10.1, 69.3+/-8.5, 68.3+/-12.0, 82.6+/-8.1, and from urine 55.9+/-9.8, 60.3+/-7.4, 77.9+/-9.1, 61.7+/-13.5, 68.6+/-8.9, 62.0+/-9.5, 72.9+/-9.1, and 72.1+/-8.0, for pyridostigmine bromide, DEET, permethrin, N-methyl-3-hydroxypyridinium bromide, m-toluamide, m-toluic acid, m-phenoxybenzyl alcohol and m-phenoxybenzoic acid, respectively. The relationship between peak areas and concentration was linear over the range between 100 and 5000 ng/ml. This method was applied to analyze the above chemicals and metabolites following their administration in rats.

Synthesis and characterization of new N-heterocyclic carbene ligands: 1,3-Bis(acetamide)imidazol-3-ium bromide and 3-(acetamide)-1-(3-aminopropyl)-1H-imidazol-3-ium bromide

NASA Astrophysics Data System (ADS)

Turkyilmaz, Murat; Uluçam, Gühergül; Aktaş, Şaban; Okan, S. Erol

2017-05-01

Two new pincer type N-heterocyclic carbene ligands were synthesized. The compounds were characterized by FTIR, NMR (1H, 13C) GC-MS and elemental analyses. They were also both modelled by DFT calculations as the crystal structure of 1,3-bis(acetamide)imidazol-3-ium bromide was determined by XRD which is an orthorhombic system with space group P21212. The structural analyses in gas phase were realized by comparing the experimental NMR and IR spectra with those of the theoretical calculations. In vitro biological activities of the molecules were determined and found that one of them exhibits significant cytotoxic activity.

40 CFR 180.123a - Inorganic bromide residues in peanut hay and peanut hulls; statement of policy.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Inorganic bromide residues in peanut hay and peanut hulls; statement of policy. 180.123a Section 180.123a Protection of Environment... combines and leave the hay on the ground to be incorporated into the soil, some growers follow the practice...

Classifying the Basic Parameters of Ultraviolet Copper Bromide Laser

NASA Astrophysics Data System (ADS)

Gocheva-Ilieva, S. G.; Iliev, I. P.; Temelkov, K. A.; Vuchkov, N. K.; Sabotinov, N. V.

2009-10-01

The performance of deep ultraviolet copper bromide lasers is of great importance because of their applications in medicine, microbiology, high-precision processing of new materials, high-resolution laser lithography in microelectronics, high-density optical recording of information, laser-induced fluorescence in plasma and wide-gap semiconductors and more. In this paper we present a statistical study on the classification of 12 basic lasing parameters, by using different agglomerative methods of cluster analysis. The results are based on a big amount of experimental data for UV Cu+ Ne-CuBr laser with wavelengths 248.6 nm, 252.9 nm, 260.0 nm and 270.3 nm, obtained in Georgi Nadjakov Institute of Solid State Physics, Bulgarian Academy of Sciences. The relevant influence of parameters on laser generation is also evaluated. The results are applicable in computer modeling and planning the experiments and further laser development with improved output characteristics.

Adsorption Isotherm Studies of Methyl Bromide on MgO

NASA Astrophysics Data System (ADS)

Burns, Teresa; Larese, John

2004-03-01

The adsorption of methyl bromine onto highly-uniform magnesium oxide powder was studied. Methyl bromide was condensed onto the MgO substrate at temperatures between 164 K and 179 K. The layering behavior of the gas molecules was studied by a series of vapor pressure isotherms, using a high-accuracy, computer-controller system. The isotherms clearly show first layer formation at all temperatures, with second layer formation at higher temperatures; the 2D compressibility and isosteric heat of adsorption were determined. TEB sponsored by the Department of Energy EPSCOR Grant No. DE-FG02-01ER45895. JZL sponsored by start-up funds from the University of Tennessee - Knoxville and by the Division of Materials Sciences, Office of Basic Energy Sciences, U.S. Department of Energy, under contract No. DE-AC05-00OR22725 with Oak Ridge National Laboratory, managed and operated by UT-Battelle, LLC.

Stepwise cycloaddition reaction of N-phenacylbenzothiazolium bromides and nitroalkenes for tetrahydro-, dihydro- and benzo[d]pyrrolo[2,1-b]thiazoles

NASA Astrophysics Data System (ADS)

Jin, Gong; Sun, Jing; Yang, Ren-Yin; Yan, Chao-Guo

2017-04-01

The triethylamine promoted stepwise 1,3-dipolar cycloaddition reaction of N-phenacylbenzothiazolium bromides with nitroalkenes in ethanol resulted in a mixture of two isomeric tetrahydrobenzo[d]pyrrolo[2,1-b]thiazoles with cis/trans/cis- and all-trans-configurations. More importantly, the corresponding dihydrobenzo[d]pyrrolo[2,1-b]thiazoles can be selectively prepared in refluxing ethanol and the benzo[d]pyrrolo[2,1-b]thiazoles can be obtained in satisfactory yields by sequential dehydrogenation with DDQ as oxidizer. On the other hand, the similar cycloaddition reaction of N-phenacylbenzothiazolium bromides with 1-methy-1-nitroalkenes in refluxing ethanol afforded benzo[d]pyrrolo[2,1-b]thiazoles with splitting out of nitro group. The stereochemistry of the spiro compounds was clearly elucidated on the basis of NMR spectra and sixteen single crystal structures.

Architecture of the hydrophobic and hydrophilic layers as found from crystal structure analysis of N-benzyl-N,N-dimethylalkylammonium bromides.

PubMed

Hodorowicz, Maciej; Stadnicka, Katarzyna; Czapkiewicz, Jan

2005-10-01

The molecular and crystal structures of N-benzyl-N,N-dimethylalkylammonium bromides monohydrates with chain length n=8-10 have been determined. The crystals are isostructural with the N-benzyl-N,N-dimethyldodecylammonium bromide monohydrate. The structures consist of alternated hydrophobic and hydrophilic layers perpendicular to [001]. The attraction between N+ of the cation head-groups and Br- anions is achieved through weak C_H...Br interactions. The water molecules incorporated into ionic layers are donors for two O_H...Br hydrogen bonds and serve as the acceptors in two weak interactions of C_H...O type. The methylene chains, with the slightly curved general shape, have the extended all-trans conformation. The mutual packing of the chains in the hydrophobic layers is governed by weak C_H...pi interactions.

Bis(2,2'-bipyridyl-κN,N')(carbonato-κO,O')cobalt(III) bromide trihydrate.

PubMed

Ma, Peng-Tao; Wang, Yu-Xia; Zhang, Guo-Qian; Li, Ming-Xue

2007-12-06

The title complex, [Co(CO(3))(C(10)H(8)N(2))(2)]Br·3H(2)O, is isostructural with the chloride analogue. The six-coordinated octahedral [Co(2,2'-bipy)(2)CO(3)](+) cation (2,2'-bipy is 2,2'-bipyrid-yl), bromide ion and water mol-ecules are linked together via O-H⋯Br and O-H⋯O hydrogen bonds, generating a one-dimensional chain.

A clean start to productive orchards and vineyards: recent research on methyl bromide alternatives for perennial crop nurseries

USDA-ARS?s Scientific Manuscript database

Methyl bromide (MB) is an important pest management tool in open field perennial crop nurseries in California for control of many soil borne pests including plant parasitic nematodes, pathogens, and weeds. Because MB is being phased out under the provisions of the Montreal Protocol, alternatives are...

Rejection of Bromide and Bromate Ions by a Ceramic Membrane.

PubMed

Moslemi, Mohammadreza; Davies, Simon H; Masten, Susan J

2012-12-01

Effects of pH and the addition of calcium chloride (CaCl(2)) on bromate (BrO(3) (-)) and bromide (Br(-)) rejection by a ceramic membrane were investigated. Rejection of both ions increased with pH. At pH 8, the rejection of BrO(3) (-) and Br(-) was 68% and 63%, respectively. Donnan exclusion appears to play an important role in determining rejection of BrO(3) (-) and Br(-). In the presence of CaCl(2), rejection of BrO(3) (-) and Br(-) ions was greatly reduced, confirming the importance of electrostatic interactions in determining rejection of BrO(3) (-) and Br(-). The effect of Ca(2+) is so pronounced that in most natural waters, rejection of both BrO(3) (-) and Br(-) by the membrane would be extremely small.

Iodide, bromide, and ammonium in hydraulic fracturing and oil and gas wastewaters: environmental implications.

PubMed

Harkness, Jennifer S; Dwyer, Gary S; Warner, Nathaniel R; Parker, Kimberly M; Mitch, William A; Vengosh, Avner

2015-02-03

The expansion of unconventional shale gas and hydraulic fracturing has increased the volume of the oil and gas wastewater (OGW) generated in the U.S. Here we demonstrate that OGW from Marcellus and Fayetteville hydraulic fracturing flowback fluids and Appalachian conventional produced waters is characterized by high chloride, bromide, iodide (up to 56 mg/L), and ammonium (up to 420 mg/L). Br/Cl ratios were consistent for all Appalachian brines, which reflect an origin from a common parent brine, while the I/Cl and NH4/Cl ratios varied among brines from different geological formations, reflecting geogenic processes. There were no differences in halides and ammonium concentrations between OGW originating from hydraulic fracturing and conventional oil and gas operations. Analysis of discharged effluents from three brine treatment sites in Pennsylvania and a spill site in West Virginia show elevated levels of halides (iodide up to 28 mg/L) and ammonium (12 to 106 mg/L) that mimic the composition of OGW and mix conservatively in downstream surface waters. Bromide, iodide, and ammonium in surface waters can impact stream ecosystems and promote the formation of toxic brominated-, iodinated-, and nitrogen disinfection byproducts during chlorination at downstream drinking water treatment plants. Our findings indicate that discharge and accidental spills of OGW to waterways pose risks to both human health and the environment.

The Acetyl Bromide Method Is Faster, Simpler and Presents Best Recovery of Lignin in Different Herbaceous Tissues than Klason and Thioglycolic Acid Methods

PubMed Central

Moreira-Vilar, Flavia Carolina; Siqueira-Soares, Rita de Cássia; Finger-Teixeira, Aline; de Oliveira, Dyoni Matias; Ferro, Ana Paula; da Rocha, George Jackson; Ferrarese, Maria de Lourdes L.; dos Santos, Wanderley Dantas; Ferrarese-Filho, Osvaldo

2014-01-01

We compared the amount of lignin as determined by the three most traditional methods for lignin measurement in three tissues (sugarcane bagasse, soybean roots and soybean seed coat) contrasting for lignin amount and composition. Although all methods presented high reproducibility, major inconsistencies among them were found. The amount of lignin determined by thioglycolic acid method was severely lower than that provided by the other methods (up to 95%) in all tissues analyzed. Klason method was quite similar to acetyl bromide in tissues containing higher amounts of lignin, but presented lower recovery of lignin in the less lignified tissue. To investigate the causes of the inconsistencies observed, we determined the monomer composition of all plant materials, but found no correlation. We found that the low recovery of lignin presented by the thioglycolic acid method were due losses of lignin in the residues disposed throughout the procedures. The production of furfurals by acetyl bromide method does not explain the differences observed. The acetyl bromide method is the simplest and fastest among the methods evaluated presenting similar or best recovery of lignin in all the tissues assessed. PMID:25330077

Pyridostigmine bromide and the long-term subjective health status of a sample of female reserve component Gulf War veterans: a brief report.

PubMed

Schumm, W R; Reppert, E J; Jurich, A P; Bollman, S R; Castelo, C; Sanders, D; Webb, F J

2001-02-01

The role of pyridostigmine bromide (PB) pills in explaining the long-term subjective health status of a sample of over 100 female Reserve Component Gulf War veterans was examined through regression analysis. Results fell just short of significance (p < .06) for the prediction of subjective health approximately six years after the war and were clearly not significant for the prediction of subjective health at previous times. Results parallel Golomb's 1999 RAND report, which found suggestive but not conclusive evidence for the possible adverse effects of Gulf War veterans' consumption of pyridostigmine bromide pills. Our data suggest that use of more than 10 pills may have been especially risky with respect to long-term subjective health.

Enhancement of frequency domain indices of heart rate variability by cholinergic stimulation with pyridostigmine bromide.

PubMed

Zarei, Ali Asghar; Foroutan, Seyyed Abbas; Foroutan, Seyyed Mohsen; Erfanian Omidvar, Abbas

2011-01-01

Pyridostigmine bromide (PB) is a reversible cholinesterase inhibitor. The aim of this study was to determine the effect of orally administration of single dose sustained-released tablet of pyridostigmine bromide (PBSR) on the frequency domain indices of heart rate variability (HRV). Thirty-two healthy young men were participated in this study. They were divided into 2 groups; the pyridostigmine group (n = 22) and the placebo group (n = 10). Electrocardiogram (ECG) was recorded at 10, 30, 60, 90, 120, 150, 180, 210, 240, 300 and 420 min after PBSR administration. At each time, simultaneously, a blood sample was prepared and PB plasma concentration was measured by high-performance liquid chromatography (HPLC) method. Statistical analysis showed that in different indices of HRV, there is a significant increase in low frequency (LF) band at 300 min, but no difference in high frequency band (HF). It also showed significant decreases in normalized high frequency band (Hfnu), normalized low frequency band (Lfnu) and LF/HF ratio at 120, 240 and 300 min after PBSR administration. Maximum plasma concentration of PB was 150 min after the administration. In conclusion, administration of a single dose PBSR can enhance the frequency domains indices of HRV and improvesympathovagal balance.

Enhancement of Frequency Domain Indices of Heart Rate Variability by Cholinergic Stimulation with Pyridostigmine Bromide

PubMed Central

Zarei, Ali Asghar; Foroutan, Seyyed Abbas; Foroutan, Seyyed Mohsen; Erfanian Omidvar, Abbas

2011-01-01

Pyridostigmine bromide (PB) is a reversible cholinesterase inhibitor. The aim of this study was to determine the effect of orally administration of single dose sustained-released tablet of pyridostigmine bromide (PBSR) on the frequency domain indices of heart rate variability (HRV). Thirty-two healthy young men were participated in this study. They were divided into 2 groups; the pyridostigmine group (n = 22) and the placebo group (n = 10). Electrocardiogram (ECG) was recorded at 10, 30, 60, 90, 120, 150, 180, 210, 240, 300 and 420 min after PBSR administration. At each time, simultaneously, a blood sample was prepared and PB plasma concentration was measured by high-performance liquid chromatography (HPLC) method. Statistical analysis showed that in different indices of HRV, there is a significant increase in low frequency (LF) band at 300 min, but no difference in high frequency band (HF). It also showed significant decreases in normalized high frequency band (Hfnu), normalized low frequency band (Lfnu) and LF/HF ratio at 120, 240 and 300 min after PBSR administration. Maximum plasma concentration of PB was 150 min after the administration. In conclusion, administration of a single dose PBSR can enhance the frequency domains indices of HRV and improvesympathovagal balance. PMID:24250427

Case study: Minimization of corrosion using activated sodium bromide in a medium-size cooling tower

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nalepa, C.J.; Moore, R.M.; Golson, G.L.

1996-10-01

The process loop cooling tower at the Albemarle Process Development Center in Baton Rouge, LA has historically used chlorine as the biocide together with industry accepted phosphorus-based corrosion/scale inhibitors. Although this regimen provided biocontrol, sludge and iron build-up was a recurring problem, especially in low-velocity, small cross-sectional areas of piping. A general clean-up of the system was performed in April, 1995. This clean-up was followed with a switch to a two-component corrosion inhibitor/dispersant package. It was decided to study alternate biocides as well at this time. Activated sodium bromide was found to be particularly effective in this tower, which operatesmore » at pH {approximately}8.4. Relative to chlorine, the use of activated sodium bromide led to a decrease in general and pitting corrosion on mild steel while maintaining prior performance on admiralty brass. The reduced corrosion appears to be due to a combination of both chemical (less attack on passivated metal surfaces) and biological factors (better control of heterotrophic and sessile bacteria). These conclusions are supported by chemical analyses, corrosion meter and coupon data, dip slides, BART (biological activity reaction test) tests, and visual observations of the tower sump and heat exchanger surfaces.« less

Palladium-Catalyzed Coupling of Ammonia with Aryl Chlorides, Bromides, Iodides and Sulfonates: A General Method for the Preparation of Primary Arylamines

PubMed Central

Vo, Giang D.

2010-01-01

We report that the complex generated from Pd[P(o-tol)3]2 and the alkylbisphosphine CyPF-t-Bu is a highly active and selective catalyst for the coupling of ammonia with aryl chlorides, bromides, iodides, and sulfonates. The couplings of ammonia with this catalyst conducted with a solution of ammonia in dioxane form primary arylamines from a variety of aryl electrophiles in high yields. Catalyst loadings as low as 0.1 mol % were sufficient for reactions of many aryl chlorides and bromides. In the presence of this catalyst, aryl sulfonates also coupled with ammonia for the first time in high yields. A comparison of reactions in the presence of this catalyst versus those in the presence of existing copper and palladium systems revealed a complementary, if not broader substrate scope. The utility of this method to generate amides, imides and carbamates is illustrated by a one-pot synthesis of a small library of these carbonyl compounds from aryl bromides and chlorides. Mechanistic studies show that Pd[P(o-tol)3]2 and CyPF-t-Bu generate a more active and general catalyst than that generated from CyPF-t-Bu and palladiun(II) precursors because of the low concentration of active catalyst that is generated from the combination of palladium(II), ammonia and base. PMID:19591470

A validated HPLC method for the determination of pyridostigmine bromide, acetaminophen, acetylsalicylic acid and caffeine in rat plasma and urine.

PubMed

Abu-Qare, A W; Abou-Donia, M B

2001-12-01

A method was developed for the separation and quantification of the anti-nerve agent pyridostigmine bromide (PB; 3-dimethylaminocarbonyloxy-N-methyl pyridinium bromide), the analgesic drugs acetaminophen and acetylsalicylic acid, and the stimulant caffeine (3,7-dihydro-1,3,7-trimethyl-1-H-purine-2,6-dione) in rat plasma and urine. The compounds were extracted using C(18) Sep-Pak(R) cartridges then analyzed by high performance liquid chromatography (HPLC) with reversed phase C18 column, and UV detection at 280 nm. The compounds were separated using gradient of 1-85% acetonitrile in water (pH 3.0) at a flow rate ranging between 1 and 1.5 ml/min in a period of 14 min. The retention times ranged from 8.8 to 11.5 min. The limits of detection were ranged between 100 and 200 ng/ml, while limits of quantitation were 150-200 ng/ml. Average percentage recovery of five spiked plasma samples were 70.9+/-9.5, 73.7+/-9.8, 88.6+/-9.3, 83.9+/-7.8, and from urine 69.1+/-8.5, 74.5+/-8.7, 85.9+/-9.8, 83.2+/-9.3, for pyridostigmine bromide, acetaminophen, acetylsalicylic acid and caffeine, respectively. The relationship between peak areas and concentration was linear over range between 100 and 1000 ng/ml. The resulting chromatograms showed no interfering peaks from endogenous plasma or urine components. This method was applied to analyze these compounds following oral administration in rats.

[Affinity between CrIII and purified DNA, studied by competition with an intercalating agent: ethidium bromide].

PubMed

Vecchio, D; Balbi, C; Russo, P; Parodi, S; Santi, L

1981-05-30

The affinity between CrIII and purified calf- thymus DNA was studied at neutral pH by competition with ethidium bromide. Competition results indicated an affinity between CrIII and DNA of the order of 10(5) 1/mole. These results are in good agreement with previous results CrIII - DNA affinity was studied by the independent method of equilibrium dialysis and chromium dosage by atomic spectrometry.

Adsorption Isotherm Studies of Methyl Bromide on MgO

NASA Astrophysics Data System (ADS)

Harper, Tj; Burns, Te; Larese, Jz

2003-03-01

This research involves the adsorption of methyl bromine and methane onto highly-uniform magnesium oxide powder. Methyl bromide was condensed onto the MgO substrate at temperatures between 175 K and 179 K. The layering behavior of the gas molecules was studied by a series of vapor pressure isotherms, using a high-accuracy, computer-controlled system. The isotherms clearly show first layer formation at all temperatures, followed by a continuous layer growth to saturation. Isotherms will be presented and future work discussed. TJH and TEB research sponsored by the Department of Energy EPSCOR Grant No. DE-FG02-01ER45895. JZL research sponsored by start-up funds from the University of Tennessee - Knoxville and by the Division of Materials Sciences, Office of Basic Energy Sciences, U.S. Department of Energy, under contract No. DE-AC05-00OR22725 with Oak Ridge National Laboratory, managed and operated by UT-Battelle, LLC.

The toxic chemistry of methyl bromide.

PubMed

Bulathsinghala, A T; Shaw, I C

2014-01-01

Methyl bromide (MeBr) is a chemically reactive compound that has found use as a fire retardant and fumigant used for wood, soil, fruits and grains. Its use is banned in many countries because of its ozone-depleting properties. Despite this ban, the use of MeBr persists in some parts of the world (e.g. New Zealand) due to its important role in maintaining strict biosecurity of exported and imported products. Its high chemical reactivity leads to a broad toxicological profile ranging from acute respiratory toxicity following inhalation exposure, through carcinogenicity to neurotoxicty. In this article, we discuss the chemistry of MeBr in the context of its mechanisms of toxicity. The chemical reactivity of MeBr clearly underlies its toxicity. Bromine (Br) is electronegative and a good leaving group; the δ+ carbon thus facilitates electrophilic methylation of biological molecules including glutathione (GSH) via its δ- sulphur atom, leading to downstream effects due to GSH depletion. DNA alkylation, either directly by MeBr or indirectly due to reduction in GSH-mediated detoxification of reactive alkylating chemical species, might explain the carcinogenicity of MeBr. The neurotoxicity of MeBr is much more difficult to understand, but we speculate that methyl phosphates formed in cells might contribute to its neurone-specific toxicity via cholinesterase inhibition. Finally, evidence reviewed shows that it is unlikely for Br⁻ liberated by the metabolism of MeBr to have any toxicological effect because the Br⁻ dose is very low.

Effect of Urea on the Thermodynamics of Hexadecyltrimethylammonium Bromide Micelle Formation in Aqueous Solutions

NASA Astrophysics Data System (ADS)

Velikov, A. A.

2018-02-01

The effect of urea on the thermodynamics of hexadecyltrimethylammonium bromide (CTAB) micelle formation in aqueous urea solutions was studied by isothermal titration microcalorimetry. The thermodynamic functions of Δ H, Δ G, and Δ S of CTAB micelle formation were calculated. The critical micelle concentrations (CMC) were determined. The addition of urea to the solution decreased the micelle formation entropy. This was attributed to the "lowering" of the structural temperature of the solution, which led to an increased number of hydrogen bonds and structure formation of water.

Rejection of Bromide and Bromate Ions by a Ceramic Membrane

PubMed Central

Moslemi, Mohammadreza; Davies, Simon H.; Masten, Susan J.

2012-01-01

Abstract Effects of pH and the addition of calcium chloride (CaCl2) on bromate (BrO3−) and bromide (Br−) rejection by a ceramic membrane were investigated. Rejection of both ions increased with pH. At pH 8, the rejection of BrO3− and Br− was 68% and 63%, respectively. Donnan exclusion appears to play an important role in determining rejection of BrO3− and Br−. In the presence of CaCl2, rejection of BrO3− and Br− ions was greatly reduced, confirming the importance of electrostatic interactions in determining rejection of BrO3− and Br−. The effect of Ca2+ is so pronounced that in most natural waters, rejection of both BrO3− and Br− by the membrane would be extremely small. PMID:23236251

Large-scale, on-site confirmatory, and varietal testing of a methyl bromide quarantine treatment to control codling moth (Lepidoptera: Tortricidae) in nectarines exported to Japan.

PubMed

Yokoyama, V Y; Miller, G T; Hartsell, P L; Leesch, J G

2000-06-01

In total, 30,491 codling moth, Cydia pomonella (L.), 1-d-old eggs on May Grand nectarines in two large-scale tests, and 17,410 eggs on Royal Giant nectarines in four on-site confirmatory tests were controlled with 100% mortality after fumigation with a methyl bromide quarantine treatment (48 g3 for 2 h at > or = 21 degrees C and 50% volume chamber load) on fruit in shipping containers for export to Japan. Ranges (mean +/- SEM) were for percentage sorption 34.7 +/- 6.2 to 46.5 +/- 2.5, and for concentration multiplied by time products 54.3 +/- 0.9 to 74.5 +/- 0.6 g.h/m3 in all tests. In large-scale tests with May Grand nectarines, inorganic bromide residues 48 h after fumigation ranged from 6.8 +/- 0.7 to 6.9 +/- 0.5 ppm, which were below the U.S. Environmental Protection Agency tolerance of 20 ppm; and, organic bromide residues were < 0.01 ppm after 1 d and < 0.001 ppm after 3 d in storage at 0-1 degree C. After completion of larger-scale and on-site confirmatory test requirements, fumigation of 10 nectarine cultivars in shipping containers for export to Japan was approved in 1995. Comparison of LD50s developed for methyl bromide on 1-d-old codling moth eggs on May Grand and Summer Grand nectarines in 1997 versus those developed for nine cultivars in the previous 11 yr showed no significant differences in codling moth response among the cultivars.

To compare the effect of camylofin dihydrochloride (anafortin) with combination of valethamate bromide (epidosin) and hyoscine butyl-N-bormide (buscopan) on cervical dilation.

PubMed

Sarbhjit, Kaur; S K, Bajwa; Parmjit, Kaur; Surinder, Bhupal

2013-09-01

Various drugs have been tried to hasten cervical dilatation so that problems and hazards of prolonged labour both for the mother and fetus are minimised without increasing maternal or perinatal mortality and morbidity. To compare the effect of camylofin dihydrochloride with combination of valethemate bromide (epidosin) & hyoscine N butyl bromide (buscopan) on cervical dilatation, evaluate the incidence of side effects and to look for neonatal outcome. Two hundred cases were included of primigravidae or multigravidae with gestational age of 37 to 40 weeks with full term with single foetus,vertex presentation and no major antenatal complication of women in labour, admitted to labour room of gynaecology Department, Government Medical College, Patiala, India, was studied and divided into 2 groups Group A-100 Cases - labour accelerated by camylofin dihydro chloride and Group B-100 Cases-labour accelerated by valethemate bromide (epidosin) and hyoscine N butyl bromide. The mean age, parity and period of gestation in Anafortan group was 24.13 ± 3.60 years, 49% primigravidae and 51% multigravidae and 38.81 ± 1.09 weeks, while that in Epidosin + Buscopan group was 24.43 ± 3.42 years, 45% primigravidae and 51% multigravidae and 38.94 ± 1.09 weeks respectively. The difference was insignificant and both the groups were comparable. Mean duration of Active phase of 1st stage of labor was 141.40 ± 55.41 minutes in Anafortan group and 181.46 ± 75.58 minutes in Epidosin + Buscopan group. Mean rate of cervical dilatation according to active phase of first stage was 3.33 ± 1.03 cm/hours in Anafortan group and 2.69 ± 1.03 cm/hr in Epidosin + Buscopan group. The difference between the two groups is highly significant (p < 0.01) thus it is concluded that Anafortan hastened the rate of cervical dilatation.

Controlling First-Row Catalysts: Amination of Aryl and Heteroaryl Chlorides and Bromides with Primary Aliphatic Amines Catalyzed by a BINAP-Ligated Single-Component Ni(0) Complex

PubMed Central

2015-01-01

First-row metal complexes often undergo undesirable one-electron redox processes during two-electron steps of catalytic cycles. We report the amination of aryl chlorides and bromides with primary aliphatic amines catalyzed by a well-defined, single-component nickel precursor (BINAP)Ni(η2-NC-Ph) (BINAP = 2,2′-bis(biphenylphosphino)-1,1′-binaphthalene) that minimizes the formation of Ni(I) species and (BINAP)2Ni. The scope of the reaction encompasses electronically varied aryl chlorides and nitrogen-containing heteroaryl chlorides, including pyridine, quinoline, and isoquinoline derivatives. Mechanistic studies support the catalytic cycle involving a Ni(0)/Ni(II) couple for this nickel-catalyzed amination and are inconsistent with a Ni(I) halide intermediate. Monitoring the reaction mixture by 31P NMR spectroscopy identified (BINAP)Ni(η2-NC-Ph) as the resting state of the catalyst in the amination of both aryl chlorides and bromides. Kinetic studies showed that the amination of aryl chlorides and bromides is first order in both catalyst and aryl halide and zero order in base and amine. The reaction of a representative aryl chloride is inverse first order in PhCN, but the reaction of a representative aryl bromide is zero order in PhCN. This difference in the order of the reaction in PhCN indicates that the aryl chloride reacts with (BINAP)Ni(0), formed by dissociation PhCN from (BINAP)Ni(η2-NC-Ph), but the aryl bromide directly reacts with (BINAP)Ni(η2-NC-Ph). The overall kinetic behavior is consistent with turnover-limiting oxidative addition of the aryl halide to Ni(0). Several pathways for catalyst decomposition were identified, such as the formation of the catalytically inactive bis(amine)-ligated arylnickel(II) chloride, (BINAP)2Ni(0), and the Ni(I) species [(BINAP)Ni(μ-Cl)]2. By using a well-defined nickel complex as catalyst, the formation of (BINAP)2Ni(0) is avoided and the formation of the Ni(I) species [(BINAP)Ni(μ-Cl)]2 is minimized. PMID:24397570

Development of a high-performance liquid chromatographic method for the quantification of chlorpyrifos, pyridostigmine bromide, N,N-diethyl-m-toluamide and their metabolites in rat plasma and urine.

PubMed

Abu-Qare, A W; Abou-Donia, M B

2001-04-25

A method was developed for the separation and quantification of the insecticide chlorpyrifos (O,O-diethyl-O[3,5,6-trichloro-2-pyridinyl] phosphorothioate), its metabolites chlorpyrifos-oxon (O,O-diethyl-O[3,5,6-trichloro-2-pyridinyl] phosphate) and TCP (3,5,6-trichloro-2-pyridinol), the anti-nerve agent drug pyridostigmine bromide (PB; 3-dimethylaminocarbonyloxy-N-methyl pyridinium bromide), its metabolite N-methyl-3-hydroxypyridinium bromide, the insect repellent DEET (N,N-diethyl-m-toluamide), and its metabolites m-toluamide and m-toluic acid in rat plasma and urine. The method is based on using solid-phase extraction and high-performance liquid chromatography (HPLC) with reversed-phase C18 column, and gradient UV detection ranging between 210 and 280 nm. The compounds were separated using a gradient of 1-85% acetonitrile in water (pH 3.20) at a flow-rate ranging between 1 and 1.7 ml/min over a period of 15 min. The retention times ranged from 5.4 to 13.2 min. The limits of detection ranged between 20 and 150 ng/ml, while the limits of quantitation were between 150 and 200 ng/ml. Average percentage recovery of five spiked plasma samples was 80.2+/-7.9, 74.9+/-8.5, 81.7+/-6.9, 73.1+/-7.8, 74.3+/-8.3, 80.8+/-6.6, 81.6+/-7.3 and 81.4+/-6.5, and from urine 79.4+/-6.9, 77.8+/-8.4, 83.3+/-6.6, 72.8+/-9.0, 76.3+/-7.7, 83.4+/-7.9, 81.6+/-7.9 and 81.8+/-6.8 for chlorpyrifos, chlorpyrifos-oxon, TCP, pyridostigmine bromide, N-methyl-3-hydroxypyridinium bromide, DEET, m-toluamide and m-toluic acid, respectively. The relationship between peak areas and concentration was linear over a range between 200 and 2000 ng/ml.

Nanosized sustained-release pyridostigmine bromide microcapsules: process optimization and evaluation of characteristics

PubMed Central

Tan, Qunyou; Jiang, Rong; Xu, Meiling; Liu, Guodong; Li, Songlin; Zhang, Jingqing

2013-01-01

Background Pyridostigmine bromide (3-[[(dimethylamino)-carbonyl]oxy]-1-methylpyridinium bromide), a reversible inhibitor of cholinesterase, is given orally in tablet form, and a treatment schedule of multiple daily doses is recommended for adult patients. Nanotechnology was used in this study to develop an alternative sustained-release delivery system for pyridostigmine, a synthetic drug with high solubility and poor oral bioavailability, hence a Class III drug according to the Biopharmaceutics Classification System. Novel nanosized pyridostigmine-poly(lactic acid) microcapsules (PPNMCs) were expected to have a longer duration of action than free pyridostigmine and previously reported sustained-release formulations of pyridostigmine. Methods The PPNMCs were prepared using a double emulsion-solvent evaporation method to achieve sustained-release characteristics for pyridostigmine. The preparation process for the PPNMCs was optimized by single-factor experiments. The size distribution, zeta potential, and sustained-release behavior were evaluated in different types of release medium. Results The optimal volume ratio of inner phase to external phase, poly(lactic acid) concentration, polyvinyl alcohol concentration, and amount of pyridostigmine were 1:10, 6%, 3% and 40 mg, respectively. The negatively charged PPNMCs had an average particle size of 937.9 nm. Compared with free pyridostigmine, PPNMCs showed an initial burst release and a subsequent very slow release in vitro. The release profiles for the PPNMCs in four different types of dissolution medium were fitted to the Ritger-Peppas and Weibull models. The similarity between pairs of dissolution profiles for the PPNMCs in different types of medium was statistically significant, and the difference between the release curves for PPNMCs and free pyridostigmine was also statistically significant. Conclusion PPNMCs prepared by the optimized protocol described here were in the nanometer range and had good uniformity

Nanosized sustained-release pyridostigmine bromide microcapsules: process optimization and evaluation of characteristics.

PubMed

Tan, Qunyou; Jiang, Rong; Xu, Meiling; Liu, Guodong; Li, Songlin; Zhang, Jingqing

2013-01-01

Pyridostigmine bromide (3-[[(dimethylamino)-carbonyl]oxy]-1-methylpyridinium bromide), a reversible inhibitor of cholinesterase, is given orally in tablet form, and a treatment schedule of multiple daily doses is recommended for adult patients. Nanotechnology was used in this study to develop an alternative sustained-release delivery system for pyridostigmine, a synthetic drug with high solubility and poor oral bioavailability, hence a Class III drug according to the Biopharmaceutics Classification System. Novel nanosized pyridostigmine-poly(lactic acid) microcapsules (PPNMCs) were expected to have a longer duration of action than free pyridostigmine and previously reported sustained-release formulations of pyridostigmine. The PPNMCs were prepared using a double emulsion-solvent evaporation method to achieve sustained-release characteristics for pyridostigmine. The preparation process for the PPNMCs was optimized by single-factor experiments. The size distribution, zeta potential, and sustained-release behavior were evaluated in different types of release medium. The optimal volume ratio of inner phase to external phase, poly(lactic acid) concentration, polyvinyl alcohol concentration, and amount of pyridostigmine were 1:10, 6%, 3% and 40 mg, respectively. The negatively charged PPNMCs had an average particle size of 937.9 nm. Compared with free pyridostigmine, PPNMCs showed an initial burst release and a subsequent very slow release in vitro. The release profiles for the PPNMCs in four different types of dissolution medium were fitted to the Ritger-Peppas and Weibull models. The similarity between pairs of dissolution profiles for the PPNMCs in different types of medium was statistically significant, and the difference between the release curves for PPNMCs and free pyridostigmine was also statistically significant. PPNMCs prepared by the optimized protocol described here were in the nanometer range and had good uniformity, with significantly slower pyridostigmine

Reactivity of BrCl, Br₂, BrOCl, Br₂O, and HOBr toward dimethenamid in solutions of bromide + aqueous free chlorine.

PubMed

Sivey, John D; Arey, J Samuel; Tentscher, Peter R; Roberts, A Lynn

2013-02-05

HOBr, formed via oxidation of bromide by free available chlorine (FAC), is frequently assumed to be the sole species responsible for generating brominated disinfection byproducts (DBPs). Our studies reveal that BrCl, Br(2), BrOCl, and Br(2)O can also serve as brominating agents of the herbicide dimethenamid in solutions of bromide to which FAC was added. Conditions affecting bromine speciation (pH, total free bromine concentration ([HOBr](T)), [Cl(-)], and [FAC](o)) were systematically varied, and rates of dimethenamid bromination were measured. Reaction orders in [HOBr](T) ranged from 1.09 (±0.17) to 1.67 (±0.16), reaching a maximum near the pK(a) of HOBr. This complex dependence on [HOBr](T) implicates Br(2)O as an active brominating agent. That bromination rates increased with increasing [Cl(-)], [FAC](o) (at constant [HOBr](T)), and excess bromide (where [Br(-)](o)>[FAC](o)) implicate BrCl, BrOCl, and Br(2), respectively, as brominating agents. As equilibrium constants for the formation of Br(2)O and BrOCl (aq) have not been previously reported, we have calculated these values (and their gas-phase analogues) using benchmark-quality quantum chemical methods [CCSD(T) up to CCSDTQ calculations plus solvation effects]. The results allow us to compute bromine speciation and hence second-order rate constants. Intrinsic brominating reactivity increased in the order: HOBr ≪ Br(2)O < BrOCl ≈ Br(2) < BrCl. Our results indicate that species other than HOBr can influence bromination rates under conditions typical of drinking water and wastewater chlorination.

Bi{sub 6}(SeO{sub 3}){sub 3}O{sub 5}Br{sub 2}: A new bismuth oxo-selenite bromide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berdonosov, Peter S., E-mail: berdonosov@inorg.chem.msu.ru; Olenev, Andrei V.; Kirsanova, Maria A.

2012-12-15

A new bismuth oxo-selenite bromide Bi{sub 6}(SeO{sub 3}){sub 3}O{sub 5}Br{sub 2} was synthesized and structurally characterized. The crystal structure belongs to the triclinic system (space group P1-bar , Z=2, a=7.1253(7) A, b=10.972(1) A, c=12.117(1) A, {alpha}=67.765(7) Degree-Sign , {beta}=82.188(8) Degree-Sign , {gamma}=78.445(7) Degree-Sign ) and is unrelated to those of other known oxo-selenite halides. It can be considered as an open framework composed of BiO{sub x} or BiO{sub y}Br{sub z} polyhedrons forming channels running along [1 0 0] direction which contain the selenium atoms in pyramidal shape oxygen coordination (SeO{sub 3}E). The spectroscopic properties and thermal stability were studied. Themore » new compound is stable up to 400 Degree-Sign C. - graphical abstract: New bismuth oxo-selenite bromide with new open framework structure. Highlights: Black-Right-Pointing-Pointer New bismuth oxo-selenite bromide was found and structurally characterized. Black-Right-Pointing-Pointer Bi{sub 6}(SeO{sub 3}){sub 3}O{sub 5}Br{sub 2} exhibit a new open framework structure type. Black-Right-Pointing-Pointer BiO{sub x} or BiO{sub y}Br{sub z} polyhedrons form channels in the structure which are decorated by [SeO{sub 3}E] groups.« less

Palladium-catalyzed coupling of ammonia with aryl chlorides, bromides, iodides, and sulfonates: a general method for the preparation of primary arylamines.

PubMed

Vo, Giang D; Hartwig, John F

2009-08-12

We report that the complex generated from Pd[P(o-tol)(3)](2) and the alkylbisphosphine CyPF-t-Bu is a highly active and selective catalyst for the coupling of ammonia with aryl chlorides, bromides, iodides, and sulfonates. The couplings of ammonia with this catalyst conducted with a solution of ammonia in dioxane form primary arylamines from a variety of aryl electrophiles in high yields. Catalyst loadings as low as 0.1 mol % were sufficient for reactions of many aryl chlorides and bromides. In the presence of this catalyst, aryl sulfonates also coupled with ammonia for the first time in high yields. A comparison of reactions in the presence of this catalyst versus those in the presence of existing copper and palladium systems revealed a complementary, if not broader, substrate scope. The utility of this method to generate amides, imides, and carbamates is illustrated by a one-pot synthesis of a small library of these carbonyl compounds from aryl bromides and chlorides, ammonia, and acid chlorides or anhydrides. Mechanistic studies show that reactions conducted with the combination of Pd[P(o-tol)(3)](2) and CyPF-t-Bu as catalyst occur with faster rates and higher yields than those conducted with CyPF-t-Bu and palladiun(II) as catalyst precursors because of the low concentration of active catalyst that is generated from the combination of palladium(II), ammonia, and base.

Preparation and evaluation of a novel hybrid monolithic column based on pentafluorobenzyl imidazolium bromide ionic liquid.

PubMed

Shan, Yuanhong; Qiao, Lizhen; Shi, Xianzhe; Xu, Guowang

2015-01-02

To develop a novel hybrid monolithic column based on pentafluorobenzyl imidazolium bromide ionic liquid, a new ionic liquid monomer was synthesized from 1-vinylimidazole and pentafluorobenzyl bromide. By employing a facile one-step copolymerization of polyhedral-oligomeric-silsesquioxane-type (POSS) cross-linking agent and the home-made ionic liquid monomer, the hybrid monolithic columns were in situ fabricated in fused-silica capillary. The morphology of monolithic column was characterized by scanning electron microscope (SEM) and the chemical composition was confirmed by Fourier-transform infrared spectroscopy (FT-IR) and elemental analysis. Excellent mechanical stability and slight swelling propensity were exhibited which was ascribed to the rigid hybrid monolithic skeleton. Reproducibility results of run-to-run, column-to-column, batch-to-batch and day-to-day were investigated and the RSDs were less than 0.46%, 1.84%, 3.96% and 3.17%, respectively. The mixed-mode retention mechanism with hydrophobic interaction, π-π stacking, ion-exchange, electrostatic interaction and dipole-dipole interaction was explored systematically using analytes with different structure types. Satisfied separation capability and column efficiency were achieved for the analysis of small molecular compounds such as alkylbenzenes, polycyclic aromatic hydrocarbons, nucleosides and halogenated compounds. Copyright © 2014 Elsevier B.V. All rights reserved.

Multimetallic Catalysis Enabled Cross-Coupling of Aryl Bromides with Aryl Triflates

PubMed Central

Ackerman, Laura K.G.; Lovell, Matthew M.

2015-01-01

Transition metal-catalyzed strategies for the formation of new C-C bonds have revolutionized the field of organic chemistry, enabling the efficient synthesis of ligands, materials, and biologically active molecules.1–3 In cases where a single metal fails to promote a selective or efficient transformation, the synergistic cooperation4 of two distinct catalysts – multimetallic catalysis – can be employed instead. Many important reactions rely on multimetallic catalysis,5 including the Wacker oxidation of olefins6–8 and the Sonogashira coupling of alkynes with aryl halides.9–10 However, the application of this strategy, even in recently developed methods11, has largely been limited to the use of metals with distinct reactivities, with only one metal catalyst undergoing an oxidative addition.12 In this manuscript, we demonstrate that cooperativity between two d10 metal catalysts, (bipyridine)nickel and (1,3-bis(diphenylphosphino)propane)palladium, enables a general cross-Ullman reaction.13–15 Our method couples aryl bromides with aryl triflates directly, eliminating the use of arylmetal reagents and avoiding the challenge of differentiating between multiple C–H bonds that is required for many C–H activation methods.16–17 The selectivity does not require an excess of either substrate and originates from the orthogonal activity of the two catalysts and the relative stability of the two arylmetal intermediates. While (dppp)Pd reacts preferentially with aryl triflates to afford a persistent intermediate, (bpy)Ni reacts preferentially with aryl bromides to form a transient, reactive intermediate. Although each catalyst forms less than 5% cross product in isolation, together they are able to achieve up to 94% yield. Our results reveal a new, general method for the synthesis of biaryls, heteroaryls, and dienes, as well as a new mechanism for selective transmetalation between two catalysts. We anticipate that this reaction will simplify the synthesis of

Methyl bromide and the Montreal Protocol: An update on the critical use exemption and quarantine pre-shipment process

Treesearch

Scott Enebak

2007-01-01

Over the past 50 years, methyl bromide (MBr) has proven to be a consistently reliable pesticide that enhances seedling production and suppresses soilborne pests. It is the industry standard and an essential component of virtually every pest management program in southern forest tree nurseries. Due to the listing of MBr as a ozone depleting substance, the U.S....

Protection of human muscle acetylcholinesterase from soman by pyridostigmine bromide.

PubMed

Maselli, Ricardo A; Henderson, John D; Ng, Jarae; Follette, David; Graves, Gregory; Wilson, Barry W

2011-04-01

Pretreatment with pyridostigmine bromide (PB) of human intercostal muscle fibers exposed to the irreversible acetylcholinesterase (AChE) inhibitor soman was investigated. Muscles were pretreated with 3 × 10(-6) M PB or saline for 20 minutes, then exposed to 10(-7) M soman for 10 minutes. AChE of muscles treated with soman alone was inhibited >95%. In contrast, PB pretreatment of soman-exposed bundles protected 20% of AChE activity. AChE of bundles exposed to PB alone recovered after 4 hours, but bundles exposed to both PB and soman did not. Soman-induced reduction of resting membrane potentials and increment of amplitudes and decay times of miniature endplate potentials (MEPPs) were partially corrected by PB pretreatment. In vitro pretreatment of human muscles with PB protected up to 20% of muscle AChE and ameliorated some deleterious effects on endplate physiology induced by soman. Copyright © 2011 Wiley Periodicals, Inc.

Corrosion of carbon steels, stainless steels, and titanium in aqueous lithium bromide solution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guinon, J.L.; Garcia-Anton, J.; Perez-Herranz, V.

1994-03-01

Effects of lithium bromide (LiBr) concentration, pH, temperature, exposure time, and the action of some inhibitors on corrosion of several carbon (C) steels, stainless steels (SS), and a titanium (Ti) alloy were studied. Corrosion rates were determined by the polarization resistance method and compared to rates determined by weight-loss measurements. Pitting potentials (E[sub p]) were evaluated in neutral LiBr solution and with different inhibitors. Pit density and average pit depth depended on the metal tested, with lowest values for Ti, the next lowest values for type 316 SS (UNS S31600), and the highest values for UNS G41350 tempered steel.

Preparation and in vitro evaluation of pyridostigmine bromide microparticles.

PubMed

Hegazy, Nahed; Demirel, Müzeyyen; Yazan, Yasemin

2002-08-21

Pyridostigmine bromide (PB) is an anticholinesterase agent whose aqueous solubility is high and which has a short elimination half-life. Its dosage rate in the treatment of myastenia gravis is frequent due to the short half-life and it exhibits side effects. Microparticles designed to deliver a pharmaceutical active ingredient efficiently at the minimum dose and also to enhance stability, reduce side effects and modify drug release were prepared in this study using an acrylic polymer (Eudragit) as the vehicle by the spray-drying technique. The drug was either dissolved or dispersed in the polymeric solution and following the preparation of microparticles using different ratios of ingredients, characterization studies including the determination of shape, particle size distribution, amount loaded, release and stability of PB were performed. The results obtained were compared to those of pure PB. Drug release from microparticles could be modified and was found to depend on the shapes of the microparticles. In vitro evaluation results indicate that the frequent dosage and side effects of pure PB may be reduced with the formulation of microparticles.

Factors affecting a cyanogen bromide-based assay of thiamin.

PubMed

Wyatt, D T; Lee, M; Hillman, R E

1989-11-01

We analyzed extensively a modified thiochrome method for thiamin analysis. Acid phosphatase (EC 3.1.3.2) from potato was superior to either alpha-amylase or acid phosphatase from wheat germ as a dephosphorylating agent. Timing of cyanogen bromide exposure was important, but the assay had good precision and accuracy. The standard curve was linear from 10 to 3000 nmol/L. The within-run and between-run coefficients of variation for total thiamin in whole blood were 3.6% and 7.4%, respectively. Analytical recoveries for low, intermediate, and high additions of thiamin to whole blood were 93-109%. Sample yield was increased by 41% (+/- 29% SD) with pre-assay freezing. Samples were stable for two days at room temperature, for seven days when refrigerated, and for two years when frozen. Previously unreported interference was seen with penicillin derivatives, and with several commonly used diuretic and antiepileptic medications. This assay may be suitable for population screening; 200 samples could be analyzed weekly at a cost of +0.20 per sample.

[Treatment of cetyltrimethyl ammonium bromide wastewater by potassium ferrate].

PubMed

Yang, Wei-hua; Wang, Hong-hui; Zeng, Xiao-xu; Huang, Ting-ting

2009-08-15

A novel oxidant potassium ferrate (K2FeO4) was used to remove cetyltrimethyl ammonium bromide (CTAB) at room temperature. The effects of various conditions on the removal ratio, such as reaction time, dosing quantity of K2FeO4 and initial pH, were investigated. The experiments results show that the removal ratio reaches 79.4% when the reaction time is 30 min, the dosing quantity of K2FeO4 to CTAB is 1:1, the initial pH of the solution is 7. In the reaction progress, the oxidation of K2FeO4 and the flocculation of the reduction product have synergistic effect on the removal of CTAB. In addition, infrared spectra of CTAB before and after being treated with K2FeO4 were further studied. The results indicate that the degradation process involves the interruption of chain and the subsequent mineralization to inorganic molecules. Furthermore, the reaction of K2FeO4 and CTAB follows second order kinetics law.

[Neuromuscular blocking effects of Org 9426 (rocuronium bromide); a comparative study with vecuronium bromide in Japanese patients].

PubMed

Shingu, Koh; Masuzawa, Munehiro; Omote, Keiichi; Namiki, Akiyoshi; Kikuchi, Hirosato; Kawamada, Miwako; Sato, Shigehito; Kimura, Tomomasa; Hatano, Norio; Nakatsuka, Hideki; Morita, Kiyoshi; Hara, Tetsuya; Kanmura, Yuichi; Takeda, Junzo

2006-09-01

Efficacy and safety of Org 9426 were compared with those of vecuronium bromide in Japanese patients. We studied 88 Japanese patients undergoing surgery requiring general anesthesia. Patients were allocated randomly to receive intubation dose of 0.6 mg x kg(-1), 0.9 mg x kg(-1) of Org 9426 or 0.1mg x kg(-1) of vecuronium. Following an intubation dose, patients received maintenance doses of 0.1, 0.15 or 0.2 mg x kg(-1) of Org 9426 or 0.025 mg x kg(-1) of vecuronium. The neuromuscular block was monitored with acceleromyography using TOF stimuli. Sevoflurane was administered to all treatment groups after intubation. The onset times of the 0.6 and 0.9 mg x kg(-1) of Org 9426 groups were 84.6 and 77.1 sec respectively, which showed statistical difference between the onset time of 0.1 mg x kg(-1) of vecuronium, 125.7 sec. The intubation condition was similar among three treatment groups. The clinical durations of 0.6 and 0.9 mg x kg(-1) of Org 9426 and 0.1 mg x kg(-1) of vecuronium were 53.4, 73.4 and 59.9 min, respectively. Clinical duration and spontaneous recovery time of maintenance dose of 0.15 mg x kg(-1) of Org 9426 were similar to those of 0.025 mg x kg(-1) of vecuronium. Org 9426 showed more rapid onset time than that of vecuronium and similar clinical duration and recovery times to those of vecuronium in Japanese patients.

Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Attached Vertical Stacks, More than 8 hours, 10 Foot Stack Height

EPA Pesticide Factsheets

This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Attached Vertical Stacks , 8 Hours or Less, 10 Foot Stack Height

EPA Pesticide Factsheets

This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Attached Vertical Stacks, 8 Hours or Less, 50 Foot Stack Height

EPA Pesticide Factsheets

This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Attached Vertical Stacks , 8 Hours or Less, 25 Foot Stack Height

EPA Pesticide Factsheets

This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Attached Vertical Stacks, More than 8 hours, 25 Foot Stack Height

EPA Pesticide Factsheets

This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Attached Vertical Stacks, More than 8 hours, 50 Foot Stack Height

EPA Pesticide Factsheets

This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

Studies on nitrile rubber degradation in zinc bromide completion fluid and its prevention by surface fluorination

NASA Astrophysics Data System (ADS)

Vega-Cantu, Yadira Itzel

Poly(acrylonitrile-co-butadiene) or nitrile-butadiene rubber (NBR) is frequently used as an O-ring material in the oil extraction industry due to its excellent chemical properties and resistance to oil. However, degradation of NBR gaskets is known to occur during the well completion and oil extraction process where packers are exposed to completion fluids such as ZnBr2 brine. Under these conditions NBR exhibits accelerated chemical degradation resulting in embrittlement and cracking. Samples of NBR, poly(acrylonitrile) (PAN) and poly(butadiene) (PB) have been exposed to ZnBr2 based completion fluid, and analyzed by ATR and diffuse reflectance IR. Analysis shows the ZnBr2 based completion fluid promotes hydrolysis of the nitrile group to form amides and carboxylic groups. Analysis also shows that carbon-carbon double bonds in NBR are unaffected after short exposure to zinc bromide based completion fluid, but are quickly hydrolyzed in acidic bromide mixtures. Although fluoropolymers have excellent chemical resistance, their strength is less than nitrile rubber and replacing the usual gasket materials with fluoroelastomers is expensive. However, a fluoropolymer surface on a nitrile elastomer can provide the needed chemical resistance while retaining their strength. In this study, we have shown that this can be achieved by direct fluorination, a rather easy and inexpensive process. Samples of NBR O-rings have been fluorinated by exposure to F2 and F2/HF mixtures at various temperatures. Fluorination with F 2 produces the desired fluoropolymer layer; however, fluorination by F2/HF mixtures gave a smoother fluorinated layer at lower temperatures and shorter times. Fluorinated samples were exposed to ZnBr2 drilling fluid and solvents. Elemental analysis shows that the fluorinated layer eliminates ZnBr2 diffusion into the NBR polymeric matrix. It was also found that surface fluorination significantly retards the loss of mechanical properties such as elasticity, tensile

Oxidation of Bromide to Bromine by Ruthenium(II) Bipyridine-Type Complexes Using the Flash-Quench Technique.

PubMed

Tsai, Kelvin Yun-Da; Chang, I-Jy

2017-07-17

Six ruthenium complexes, [Ru(bpy) 3 ] 2+ (1), [Ru(bpy) 2 (deeb)] 2+ (2), [Ru(deeb) 2 (dmbpy)] 2+ (3), [Ru(deeb) 2 (bpy)] 2+ (4), [Ru(deeb) 3 ] 2+ (5), and [Ru(deeb) 2 (bpz)] 2+ (6) (bpy: 2,2'-bipyridine; deeb: 4,4'-diethylester-2,2'-bipyridine; dmbpy: 4,4'-dimethyl-2,2'-bipyridine, bpz: 2,2'-bipyrazine), have been employed to sensitize photochemical oxidation of bromide to bromine. The oxidation potential for complexes 1-6 are 1.26, 1.36, 1.42, 1.46, 1.56, and 1.66 V vs SCE, respectively. The bimolecular rate constants for the quenching of complexes 1-6 by ArN 2 + (bromobenzenediazonium) are determined as 1.1 × 10 9 , 1.6 × 10 8 , 1.4 × 10 8 , 1.2 × 10 8 , 6.4 × 10 7 , and 8.9 × 10 6 M -1 s -1 , respectively. Transient kinetics indicated that Br - reacted with photogenerated Ru(III) species at different rates. Bimolecular rate constants for the oxidation of Br - by the Ru(III) species derived from complexes 1-5 are observed as 1.2 × 10 8 , 1.3 × 10 9 , 4.0 × 10 9 , 4.8 × 10 9 , and 1.1 × 10 10 , M -1 s -1 , respectively. The last reaction kinetics observed in the three-component system consisting of a Ru sensitizer, quencher, and bromide is shown to be independent of the Ru sensitizer. The final product was identified as bromine by its reaction with hexene. The last reaction kinetics is assigned to the disproportionation reaction of Br 2 -• ions, for which the rate constant is determined as 5 × 10 9 M -1 s -1 . Though complex 6 has the highest oxidation potential in the Ru(II)/Ru(III) couple, its excited state fails to react with ArN 2 + sufficiently for subsequent reactions. The Ru(III) species derived from complex 1 reacts with Br - at the slowest rate. Complexes 2-5 are excellent photosensitizers to drive photooxidation of bromide to bromine.

Effect of bromide in a surface water intake on the formation of brominated trihalomethanes at a public water system treatment plant

EPA Science Inventory

This project is a collaborative drinking water research study. EPA is evaluating water samples collected by PWS operators in order to investigate relationships between bromide in source water and the formation of brominated DBPs in finished drinking water. This study will includ...

Formation of Worm-Like Micelles in Mixed N-Hexadecyl-N-Methylpyrrolidinium Bromide-Based Cationic Surfactant and Anionic Surfactant Systems

PubMed Central

Dai, Caili; Yan, Zhihu; You, Qing; Du, Mingyong; Zhao, Mingwei

2014-01-01

Through the descriptive and rheological characterization of worm-like micelles formed by N-hexadecyl-N-methylpyrrolidinium bromide and sodium laurate, the formation and properties of the worm-like micelles were affected by the concentrations of sodium laurate and temperature. Additionally, cryogenic transmission electron microscopy images further validated the formation of worm-like micelles. PMID:25019152

The Aerobic Oxidation of Bromide to Dibromine Catalyzed by Homogeneous Oxidation Catalysts and Initiated by Nitrate in Acetic Acid

DOE Office of Scientific and Technical Information (OSTI.GOV)

Partenheimer, Walt; Fulton, John L.; Sorensen, Christina M.

A small amount of nitrate, ~0.002 molal, initiates the Co/Mn catalyzed aerobic oxidation of bromide compounds (HBr,NaBr,LiBr) to dibromine in acetic acid at room temperature. At temperatures 40oC or less , the reaction is autocatalytic. Co(II) and Mn(II) themselves and mixed with ionic bromide are known homogeneous oxidation catalysts. The reaction was discovered serendipitously when a Co/Br and Co/Mn/Br catalyst solution was prepared for the aerobic oxidation of methyaromatic compounds and the Co acetate contained a small amount of impurity i.e. nitrate. The reaction was characterized by IR, UV-VIS, MALDI and EXAFS spectroscopies and the coordination chemistry is described. Themore » reaction is inhibited by water and its rate changed by pH. The change in these variables, as well as others, are identical to those observed during homogeneous, aerobic oxidation of akylaromatics. A mechanism is proposed. Accidental addition of a small amount of nitrate compound into a Co/Mn/Br/acetic acid mixture in a large, commercial feedtank is potentially dangerous.« less

Cetyltrimethyl Ammonium Bromide as Corrosion Inhibitor for Zinc Used in Hydrochloric Acid

NASA Astrophysics Data System (ADS)

Sun, C. X.; Du, J. J.; Ma, Z. W.; Huang, C. S.; Wu, J. Y.

2018-05-01

A compound inhibitor composed of cetyltrimethyl ammonium bromide (CTAB) and bromohexadecyl pyridine was tested as corrosion inhibitor for zinc in hydrochloric acid. The results of static coupon test show that the compound inhibitor can effectively protect zinc from corrosion and the best concentration ratio is CTAB 50 mg/L and bromohexadecyl pyridine 200 mg/L. The polarization results show that the compound inhibitor will cause a negative shift of E0 of zinc in hydrochloric acid. The EIS (electrchemical impedance spectra) results show that the inhibitor leads to a bigger radius and has one time constant. SEM results show that the CTAB and bromohexadecyl pyridine form a uniform and compact membrane on the surface of zinc that can protect zinc from corroding effectively.

Copper bromide vapour laser with an output pulse duration of up to 320 ns

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gubarev, F A; Fedorov, K V; Evtushenko, G S

We report the development of a copper bromide vapour laser with an output pulse duration of up to 320 ns. To lengthen the pulse, the discharge current was limited using a compound switch comprising a pulsed hydrogen thyratron and a tacitron. This technique permits limiting the excitation of the working levels at the initial stage of the discharge development to lengthen the inversion lifetime. The longest duration of a laser pulse was reached in tubes 25 and 50 mm in diameter for a pulse repetition rate of 2 – 4 kHz. (lasers and laser beams)

Phase diagram of tetradecyltrimethylammonium bromide (TTAB) + water + octanol system with application of mechanical deformation

NASA Astrophysics Data System (ADS)

Yavuz, Aykut Evren; Masalci, Özgür; Kazanci, Nadide

2014-11-01

Morphological properties of tetradecyltrimethylammonium bromide (TTAB) + water + octanol system in different concentrations have been studied. In the process, isotropic phase (L1) and nematic calamitic (NC), nematic discotic (ND), hexagonal E and lamellar D anizotropic mesophases have been determined by polarizing microscopy method and partial ternary phase diagram of the system set up. Textural properties of the anisotropic mesophases of the system have been discussed and their birefringence values measured. Mechanical deformation has been applied to the mesophases. The textural properties and the birefringence values have been observed to be changed by the deformation, after and before which changes have been compared.

Determination of pyridostigmine bromide and its metabolites in biological samples.

PubMed

Zhao, Bin; Moochhala, Shabbir M; Lu, Jia; Tan, Donna; Lai, Mui Hoon

2006-01-01

Pyridostigmine bromide (PB) is a quartenary ammonium compound that inhibits the hydrolysis of acetylcholine by competitive reversible binding to acetylcholinesterase. PB is used for the symptomatic treatment of myasthenia gravis and has been applied as a prophylaxis against nerve agents. Many studies on PB have involved the reliance on techniques that extract and quantify PB in biological samples. This article presents an overview of the currently applied methodologies for the determination of PB and its metabolites in various biological samples. Articles published from January 1975 to the July 2005 were taken into consideration for the discussion of the metabolism and analytical method of PB. HPLC and GC methods have been used and discussed in most of the references cited in this review. Other methods such as RIA and CE that have been recently reported are also mentioned in this article. Basic information about the type of sample used for analysis, sample preparation, chromatographic column, mobile phase, detection mode and validation data are summarized in a table.

To Compare the Effect of Camylofin Dihydrochloride (Anafortin) with Combination of Valethamate Bromide (Epidosin) and Hyoscine Butyl-N-Bormide (Buscopan) on Cervical Dilation

PubMed Central

Sarbhjit, Kaur; S.K., Bajwa; Parmjit, Kaur; Surinder, Bhupal

2013-01-01

Background: Various drugs have been tried to hasten cervical dilatation so that problems and hazards of prolonged labour both for the mother and fetus are minimised without increasing maternal or perinatal mortality and morbidity. Aims and Objectives: To compare the effect of camylofin dihydrochloride with combination of valethemate bromide (epidosin) & hyoscine N butyl bromide (buscopan) on cervical dilatation, evaluate the incidence of side effects and to look for neonatal outcome. Material and Methods: Two hundred cases were included of primigravidae or multigravidae with gestational age of 37 to 40 weeks with full term with single foetus,vertex presentation and no major antenatal complication of women in labour, admitted to labour room of gynaecology Department, Government Medical College, Patiala, India, was studied and divided into 2 groups Group A–100 Cases – labour accelerated by camylofin dihydro chloride and Group B–100 Cases–labour accelerated by valethemate bromide (epidosin) and hyoscine N butyl bromide. Observations: The mean age, parity and period of gestation in Anafortan group was 24.13 ± 3.60 years, 49% primigravidae and 51% multigravidae and 38.81 ± 1.09 weeks, while that in Epidosin + Buscopan group was 24.43 ± 3.42 years, 45% primigravidae and 51% multigravidae and 38.94 ± 1.09 weeks respectively. The difference was insignificant and both the groups were comparable. Results: Mean duration of Active phase of 1st stage of labor was 141.40 ± 55.41 minutes in Anafortan group and 181.46 ± 75.58 minutes in Epidosin + Buscopan group. Mean rate of cervical dilatation according to active phase of first stage was 3.33 ± 1.03 cm/hours in Anafortan group and 2.69 ± 1.03 cm/hr in Epidosin + Buscopan group. The difference between the two groups is highly significant (p < 0.01) thus it is concluded that Anafortan hastened the rate of cervical dilatation. PMID:24179892

The Efficacy and Safety of Topical Rocuronium Bromide to Induce Bilateral Mydriasis in Hispaniolan Amazon Parrots ( Amazona ventralis ).

PubMed

Baine, Katherine; Hendrix, Diane V H; Kuhn, Sonia E; Souza, Marcy J; Jones, Michael P

2016-03-01

The efficacy and safety of topically applied rocuronium in Hispaniolan Amazon parrots ( Amazona ventralis ) was assessed in a group of 10 adult birds. A complete ophthalmic examination (including Schirmer tear test, ocular reflexes, applanation tonometry, fluorescein staining, and slit-lamp biomicroscopy) was performed, and rocuronium bromide (0.15 mg in both eyes) was administered. Pupillary light reflex (PLR) and pupillary diameter were recorded in a darkened room at the following time points: 0, 10, 20, 30, 40, 50, 60, 80, 100, 120, 140, 160, 180, 200, 220, 240, 300, and 360 minutes, and 24 hours. Fluorescein staining in both eyes was performed at 24 hours. By 10 minutes, PLR was absent in all birds (at 5 minutes, 8 birds; at 10 minutes, remaining 2 birds). Pupil diameter differed significantly from baseline at all time points. Additionally, PLR was decreased in 7/10 birds at 360 minutes and normal in all birds at 24 hours. Superficial corneal ulceration was observed at 24 hours in the left eye of 2/10 of the birds after fluorescein stain application. This study demonstrated that rocuronium bromide was an effective mydriatic agent in Hispaniolan Amazon parrots with rapid onset and prolonged duration of action.

Pentafluorobenzyl bromide-A versatile derivatization agent in chromatography and mass spectrometry: I. Analysis of inorganic anions and organophosphates.

PubMed

Tsikas, Dimitrios

2017-02-01

Pentafluorobenzyl bromide (PFB-Br) is a versatile derivatization agent. It is widely used in chromatography and mass spectrometry since several decades. The bromide atom is largely the single leaving group of PFB-Br. It is substituted by wide a spectrum of nucleophiles in aqueous and non-aqueous systems to form electrically neutral, in most organic solvents soluble, generally thermally stable, volatile, strongly electron-capturing and ultraviolet light-absorbing derivatives. Because of these greatly favoured physicochemical properties, PFB-Br emerged an ideal derivatization agent for highly sensitive analysis of endogenous and exogenous substances including various inorganic and organic anions by electron capture detection or after electron-capture negative-ion chemical ionization in GC-MS. The present article attempts an appraisal of the utility of PFB-Br in analytical chemistry. It reviews and discusses papers dealing with the use of PFB-Br as the derivatization reagent in the qualitative and quantitative analysis of endogenous and exogenous inorganic anions in various biological samples, notably plasma, urine and saliva. These analytes include nitrite, nitrate, cyanide and dialkyl organophosphates. Special emphasis is given to mass spectrometry-based approaches and stable-isotope dilution techniques. Copyright © 2016 Elsevier B.V. All rights reserved.

Bioreactors for removing methyl bromide following contained fumigations

USGS Publications Warehouse

Miller, L.G.; Baesman, S.M.; Oremland, R.S.

2003-01-01

Use of methyl bromide (MeBr) as a quarantine, commodity, or structural fumigant is under scrutiny because its release to the atmosphere contributes to the depletion of stratospheric ozone. A closed-system bioreactor consisting of 0.5 L of a growing culture of a previously described bacterium, strain IMB-1, removed MeBr (> 110 ??mol L-1) from recirculating air. Strain IMB-1 grew slowly to high cell densities in the bioreactor using MeBr as its sole carbon and energy source. Bacterial oxidation of MeBr produced CO2 and hydrobromic acid (HBr), which required continuous neutralization with NaOH for the system to operate effectively. Strain IMB-1 was capable of sustained oxidation of large amounts of MeBr (170 mmol in 46 d). In an open-system bioreactor (10-L fermenter), strain IMB-1 oxidized a continuous supply of MeBr (220 ??mol L-1 in air). Growth was continuous, and 0.5 mol of MeBr was removed from the air supply in 14 d. The specific rate of MeBr oxidation was 7 ?? 10-16 mol cell-1 h-1. Bioreactors such as these can therefore be used to remove large quantities of contaminant MeBr, which opens the possibility of biodegradation as a practical means for its disposal.

WRAIR Protocols for Soldier Status and Readiness to Organophosphate Exposure: Unprocessed Whole Blood Cholinesterase and Pyridostigmine Bromide Quantification

DTIC Science & Technology

2003-07-01

blood in the presence and absence of selective ( huperzine - a and Iso-OMPA), and non-selective (pyridostigmine bromide) cholinesterase inhibitors...cholinesterases after exposure to CWAs such as GD and pharmaceuticals such as huperzine - a and pyridostigmine have been determined in animals and man...activity. Since urban terrorism is on the rise, Federal,State, and local authorities need a reliable, fast, inexpensive method for confirming such an

The influence of water on the physicochemical characteristics of 1-butyl-3-methylimidazolium bromide ionic liquid

NASA Astrophysics Data System (ADS)

Ramenskaya, L. M.; Grishina, E. P.; Pimenova, A. M.; Gruzdev, M. S.

2008-07-01

A modified synthesis of 1-butyl-3-methylimidazolium bromide (BMImBr) was suggested and performed, and some physicochemical properties of the product containing 0.64 13.6 wt % water were determined. Water increased the electrical conductivity and decreased the viscosity and melting point of the substance but weakly influenced its density. Water in amounts of 5 8 wt % (45 50 mol %) caused structural changes. The BMImBr · 0.5H2O crystal hydrate was found to be stable thermodynamically.

Comparison of percent hatch and fungal infestation in channel catfish eggs after copper sulfate, diquat bromide, formalin, and hydrogen peroxide treatment

USDA-ARS?s Scientific Manuscript database

Reduced survival is often a result of fungal (Saprolegnia spp.) infestation of fish eggs. However, timely chemical treatments often limit these infestations and increase survival. The effect of copper sulfate pentahydrate (CSP - 10 mg/L), diquat bromide (25 mg/L diquat cation), formalin (433 mg/L)...

Effects of Fumigant Alternatives to Methyl Bromide on Pest Control in Open Field Nursery Production of Perennial Fruit and Nut Plants

USDA-ARS?s Scientific Manuscript database

Producers of deciduous fruit and nut trees and vines rely on preplant fumigation to meet regulatory requirements designed to ensure nematode free planting stock. In the past, preplant treatments with methyl bromide or high rates of 1,3-dichloropropene were the preferred treatments. However, the ph...

Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Open Area Vertical Stacks, More than 8 Hours, 25 Foot Stack Height

EPA Pesticide Factsheets

This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Open Area Vertical Stacks , 8 Hours or Less, 5 Foot Stack Height

EPA Pesticide Factsheets

This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Open Area Vertical Stacks, More than 8 Hours, 5 Foot Stack Height

EPA Pesticide Factsheets

This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Open Area Vertical Stacks, 8 Hours or Less, 10 Foot Stack Height

EPA Pesticide Factsheets

This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Open Area Vertical Stacks, 8 Hours or Less, 50 Foot Stack Height

EPA Pesticide Factsheets

This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Open Area Vertical Stacks, 8 Hours or Less, 25 Foot Stack Height

EPA Pesticide Factsheets

This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Open Area Vertical Stacks, More than 8 Hours, 50 Foot Stack Height

EPA Pesticide Factsheets

This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

Methyl Bromide Buffer Zone Distances for Commodity and Structural Fumigation: Active Aeration, Open Area Vertical Stacks, More than 8 Hours, 10 Foot Stack Height

EPA Pesticide Factsheets

This document contains buffer zone tables required by certain methyl bromide commodity fumigant product labels that refer to Buffer Zone Lookup Tables located at epa.gov/pesticide-registration/mbcommoditybuffer on the label.

Successful treatment of migrating partial seizures in Wolf-Hirschhorn syndrome with bromide.

PubMed

Itakura, Ayako; Saito, Yoshiaki; Nishimura, Yoko; Okazaki, Tetsuya; Ohno, Koyo; Sejima, Hitoshi; Yamamoto, Toshiyuki; Maegaki, Yoshihiro

2016-08-01

A girl with mild psychomotor developmental delay developed right or left hemiclonic convulsion at 10months of age. One month later, clusters of hemiclonic or bilateral tonic seizures with eyelid twitching emerged, resulting in status epilepticus. Treatment with phenobarbital and potassium bromide completely terminated the seizures within 10days. Ictal electroencephalography revealed a migrating focus of rhythmic 3-4Hz waves from the right temporal to right frontal regions and then to the left frontal regions. Genetic analysis was conducted based on the characteristic facial appearance of the patient, which identified a 2.1-Mb terminal deletion on chromosome 4p. This is the first case of Wolf-Hirschhorn syndrome complicated by epilepsy with migrating partial seizures. Copyright © 2016 The Japanese Society of Child Neurology. Published by Elsevier B.V. All rights reserved.

Characterization of the major cyanogen bromide fragment of alpha-A crystallin

NASA Technical Reports Server (NTRS)

Ifeanyi, F.; Takemoto, L.; Spooner, B. S. (Principal Investigator)

1991-01-01

Alpha crystallin from the bovine lens has been digested with cyanogen bromide, and the major fragment (CB-1) has been purified using reverse phase HPLC. Characterization of this fragment by Edman degradation and antisera to synthetic peptides indicates that it originates from alpha-A crystallin, but lacks the N-terminal methionine and the last 35 amino acids from the C-terminus of the molecule. The purified CB-1 fragment binds as well as native alpha crystallin to lens membrane, but is unable to self-assemble into the correct size of high molecular weight oligomeric complexes characteristic of the intact alpha-A chain. Together, these results demonstrate that the alpha-A chain is comprised of at least two functional domains, one of which is involved in binding of alpha-A crystallin to lens membrane, and another which is necessary for correct self-assembly of the molecule into high molecular weight oligomers.

Characteristics of molecular weight distribution of dissolved organic matter in bromide-containing water and disinfection by-product formation properties during treatment processes.

PubMed

Zhang, Ying; Zhang, Ning; Zhao, Peng; Niu, Zhiguang

2018-03-01

The characteristics of dissolved organic matter (DOM) and bromide ion concentration have a significant influence on the formation of disinfection by-products (DBPs). In order to identify the main DBP precursors, DOM was divided into five fractions based on molecular weight (MW), trihalomethane formation potential and haloacetic acid formation potential were determined for fractions, and the change in contents of different fractions and total DBPs during treatment processes (pre-chlorination, coagulation, sand filtration, disinfection) were studied. Moreover, the relationship between bromide concentration and DBP generation characteristics in processes was also analyzed. The results showed that the main DBP precursors were the fraction with MW <1kDa and fraction with MW 3-10kDa, and the DBP's generation ability of lower molecular weight DOM (<10kDa) was higher than that of higher molecular weight DOM. During different processes, pre-chlorination and disinfection had limited effect on removing organics but could alter the MW distribution, and coagulation and filtration could effectively remove organics with higher MW. For DBPs, trihalomethanes (THMs) were mainly generated in pre-chlorination and disinfection, while haloacetic acids (HAAs) were mostly generated during pre-chlorination; coagulation and sand filtration had little effect on THMs but resulted in a slight removal of HAAs. In addition, the results of ANOVA tests suggested that molecular sizes and treatment processes have significant influence on DBP formation. With increasing bromide concentration, the brominated DBPs significantly increased, but the bromine incorporation factor in the processes was basically consistent at each concentration. Copyright © 2017. Published by Elsevier B.V.

Direct Observation of Halide Migration and its Effect on the Photoluminescence of Methylammonium Lead Bromide Perovskite Single Crystals.

PubMed

Luo, Yanqi; Khoram, Parisa; Brittman, Sarah; Zhu, Zhuoying; Lai, Barry; Ong, Shyue Ping; Garnett, Erik C; Fenning, David P

2017-11-01

Optoelectronic devices based on hybrid perovskites have demonstrated outstanding performance within a few years of intense study. However, commercialization of these devices requires barriers to their development to be overcome, such as their chemical instability under operating conditions. To investigate this instability and its consequences, the electric field applied to single crystals of methylammonium lead bromide (CH 3 NH 3 PbBr 3 ) is varied, and changes are mapped in both their elemental composition and photoluminescence. Synchrotron-based nanoprobe X-ray fluorescence (nano-XRF) with 250 nm resolution reveals quasi-reversible field-assisted halide migration, with corresponding changes in photoluminescence. It is observed that higher local bromide concentration is correlated to superior optoelectronic performance in CH 3 NH 3 PbBr 3 . A lower limit on the electromigration rate is calculated from these experiments and the motion is interpreted as vacancy-mediated migration based on nudged elastic band density functional theory (DFT) simulations. The XRF mapping data provide direct evidence of field-assisted ionic migration in a model hybrid-perovskite thin single crystal, while the link with photoluminescence proves that the halide stoichiometry plays a key role in the optoelectronic properties of the perovskite. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Use of lignin extracted from different plant sources as standards in the spectrophotometric acetyl bromide lignin method.

PubMed

Fukushima, Romualdo S; Kerley, Monty S

2011-04-27

A nongravimetric acetyl bromide lignin (ABL) method was evaluated to quantify lignin concentration in a variety of plant materials. The traditional approach to lignin quantification required extraction of lignin with acidic dioxane and its isolation from each plant sample to construct a standard curve via spectrophotometric analysis. Lignin concentration was then measured in pre-extracted plant cell walls. However, this presented a methodological complexity because extraction and isolation procedures are lengthy and tedious, particularly if there are many samples involved. This work was targeted to simplify lignin quantification. Our hypothesis was that any lignin, regardless of its botanical origin, could be used to construct a standard curve for the purpose of determining lignin concentration in a variety of plants. To test our hypothesis, lignins were isolated from a range of diverse plants and, along with three commercial lignins, standard curves were built and compared among them. Slopes and intercepts derived from these standard curves were close enough to allow utilization of a mean extinction coefficient in the regression equation to estimate lignin concentration in any plant, independent of its botanical origin. Lignin quantification by use of a common regression equation obviates the steps of lignin extraction, isolation, and standard curve construction, which substantially expedites the ABL method. Acetyl bromide lignin method is a fast, convenient analytical procedure that may routinely be used to quantify lignin.

Advanced crystal growth techniques for thallium bromide semiconductor radiation detectors

NASA Astrophysics Data System (ADS)

Datta, Amlan; Becla, Piotr; Guguschev, Christo; Motakef, Shariar

2018-02-01

Thallium Bromide (TlBr) is a promising room-temperature radiation detector candidate with excellent charge transport properties. Currently, Travelling Molten Zone (TMZ) technique is widely used for growth of semiconductor-grade TlBr crystals. However, there are several challenges associated with this type of crystal growth process including lower yield, high thermal stress, and low crystal uniformity. To overcome these shortcomings of the current technique, several different crystal growth techniques have been implemented in this study. These include: Vertical Bridgman (VB), Physical Vapor Transport (PVT), Edge-defined Film-fed Growth (EFG), and Czochralski Growth (Cz). Techniques based on melt pulling (EFG and Cz) were demonstrated for the first time for semiconductor grade TlBr material. The viability of each process along with the associated challenges for TlBr growth has been discussed. The purity of the TlBr crystals along with its crystalline and electronic properties were analyzed and correlated with the growth techniques. Uncorrected 662 keV energy resolutions around 2% were obtained from 5 mm x 5 mm x 10 mm TlBr devices with virtual Frisch-grid configuration.

Pyridostigmine bromide and the long-term subjective health status of a sample of over 700 male Reserve Component Gulf War era veterans.

PubMed

Schumm, Walter R; Reppert, Earl J; Jurich, Anthony P; Bollman, Stephan R; Webb, Farrell J; Castelo, Carlos S; Stever, James C; Kaufman, Mark; Deng, Liang-Yu; Krehbiel, Michelle; Owens, Barbara L; Hall, Carolyn A; Brown, Beverlyn F Cay; Lash, Jeanne F; Fink, Carol J; Crow, Janet R; Bonjour, Gabriele N

2002-06-01

Data from a 1996-1997 survey of approximately 700 Reserve Component male veterans indicate that the consumption of pyridostigmine bromide pills, used as a pretreatment for potential exposure to the nerve agent Soman, was a significant predictor of declines in reported subjective health status after the war, even after controlling for a number of other possible factors. Reported reactions to vaccines and other medications also predicted declines in subjective health. While higher military rank generally predicted better health during and after the war, educational attainment, minority status, number of days in theater, and age generally did not predict changes in subjective health. Although servicemembers were directed to take three pills a day, veterans reported a range of compliance--less than a fourth (24%) followed the medical instructions compared to 61% who took fewer than three pills daily and 6% who took six or more pills a day. Implications for use of pyridostigmine bromide are discussed.

Role of physical heterogeneity in the interpretation of small-scale laboratory and field observations of bacteria, microbial-sized microsphere, and bromide transport through aquifer sediments

USGS Publications Warehouse

Harvey, Ronald W.; Kinner, Nancy E.; MacDonald, Dan; Metge, David W.; Bunn, Amoret

1993-01-01

The effect of physical variability upon the relative transport behavior of microbial-sized microspheres, indigenous bacteria, and bromide was examined in field and flow-through column studies for a layered, but relatively well sorted, sandy glaciofluvial aquifer. These investigations involved repacked, sieved, and undisturbed aquifer sediments. In the field, peak abundance of labeled bacteria traveling laterally with groundwater flow 6 m downgradient from point of injection was coincident with the retarded peak of carboxylated microspheres (retardation factor, RF = 1.7) at the 8.8 m depth, but preceded the bromide peak and the retarded microsphere peak (RF = 1.5) at the 9.0 m depth. At the 9.5 m depth, the bacterial peak was coincident with both the bromide and the microsphere peaks. Although sorption appeared to be a predominant mechanism responsible for immobilization of microbial-sized microspheres in the aquifer, straining appeared to be primarily responsible for their removal in 0.6-m-long columns of repacked, unsieved aquifer sediments. The manner in which the columns were packed also affected optimal size for microsphere transport, which in one experiment was near the size of the small (∼2 μm) groundwater protozoa (flagellates). These data suggest that variability in aquifer sediment structure can be important in interpretation of both small-scale field and laboratory experiments examining microbial transport behavior.

Observation of Dihalide Elimination Upon Electron Attachment to Oxalyl Chloride and Oxalyl Bromide, 300-550 K

DTIC Science & Technology

2006-05-10

fragment CC120 and bromine The positive ion chemistry of oxalyl chloride has been analog CBrO. Total energies, enthalpies, and zero-point energy ( ZPE ...that Ar+ reacting with oxalyl bromide produced System G3a G2 b 70% CBrO+ and 30% Br+. trants-C2C1202(C2h, Ag) ZPE 0.019 93 0.019 93 COMPUTATIONAL...secondary ZPE 0.01708 0.01708 ions were carried out using the G3 compound method, pri- Total energy (0 K) -1146.717 00 -1145.904 66 marily in order to

Copper sulfate-pentahydrate-1,10-phenanthroline catalyzed amidations of alkynyl bromides. Synthesis of heteroaromatic amine substituted ynamides.

PubMed

Zhang, Yanshi; Hsung, Richard P; Tracey, Michael R; Kurtz, Kimberly C M; Vera, Eymi L

2004-04-01

A practical cross-coupling of amides with alkynyl bromides using catalytic CuSO(4).5H(2)O and 1,10-phenanthroline is described here. This catalytic protocol is more environmentally friendly than the use of CuCN or copper halides and provides a general entry for syntheses of ynamides including various new sulfonyl and heteroaromatic amine substituted ynamides. Given the interest in ynamides, this N-alkynylation of amides should be significant for the future of ynamides in organic synthesis.

Movement and fate of atrazine and bromide in central Kansas croplands

USGS Publications Warehouse

Sophocleous, M.; Townsend, M.A.; Whittemore, Donald O.

1990-01-01

Two flooding experiments were conducted at two sites with different soils to study the transport and fate of the commonly used herbicide atrazine and inorganic chemicals in the Great Bend Prairie croplands of south-central Kansas. The instantaneous profile method supplemented by the use of an organic (atrazine) and an inorganic (bromide) tracer chemical was used to characterize in situ the hydraulic and chemical properties of the appropriately instrumented field sites. Atrazine readily degraded to hydroxyatrazine and biodegradation by-products and was not detected deeper in the soil profile and underlying shallow aquifer. The classical processes of chemical movement based on porous media-equilibrium-diffuse flow did not fit the data well at either site. Incompletely mixed, slug flow appeared to predominate at one of the sites and preferential flow at the other. The slug movement caused 'piston-type' displacement of more saline solutions in the soil profile to the shallow water table. Recommendations for conducting related field studies based on our sampling experience are given. ?? 1990.

Development of an activated carbon-based electrode for the capture and rapid electrolytic reductive debromination of methyl bromide from post-harvest fumigations

USDA-ARS?s Scientific Manuscript database

Due to concerns surrounding its ozone depletion potential, there is a need for technologies to capture and destroy methyl bromide (CH3Br) emissions from post-harvest fumigations applied to control agricultural pests. Previously we described a system in which CH3Br fumes vented from fumigation chambe...

Modeling bromide effects on yields and speciation of dihaloacetonitriles formed in chlorinated drinking water.

PubMed

Roccaro, Paolo; Chang, Hyun-shik; Vagliasindi, Federico G A; Korshin, Gregory V

2013-10-15

This study examined effects of bromide on yields and speciation of dihaloacetonitrile (DHAN) species that included dichloro-, bromochloro- and dibromoacetonitriles generated in chlorinated water. Experimental data obtained using two water sources, varying concentrations and characters of Natural Organic Matter (NOM), bromide concentrations, reaction times, chlorine doses, temperatures and pHs were interpreted using a semi-phenomenological model that assumed the presence of three kinetically distinct sites in NOM (denoted as sites S1, S2 and S3) and the occurrence of sequential incorporation of bromine and chlorine into them. One site was found to react very fast with the chlorine and bromine but its contribution in the DHAN generation was very low. The site with the highest contribution to the yield of DHAN (>70%) has the lowest reaction rates. The model introduced dimensionless coefficients (denoted as φ1(DHAN), φ2(DHAN) and φ3(DHAN)) applicable to the initial DHAN generation sites and their monochlorinated and monobrominated products, respectively. These parameters were used to quantify the kinetic preference to bromine incorporation over that of chlorine. Values of these coefficients optimized for DHAN formation were indicative of the strongly preferential incorporation of bromine into the engaged NOM sites. The same set of φ(i)(DHAN) coefficients could be used to model the speciation of DHAN released from their kinetically different precursors. The dimensionless speciation coefficients φ(i)(DHAN) were determined to be site specific and dependent on the NOM content and character as well as pH. The presented model of DHAN formation and speciation can help quantify in more detail the generation of DHAN and provide more insight necessary for further assessment of their potential health effects. Copyright © 2013 Elsevier Ltd. All rights reserved.

The history and future of methyl bromide alternatives used in the production of forest seedlings in the southern United States

Treesearch

Scott A. Enebak

2013-01-01

This paper gives a brief history of the Southern Forest Nursery Management Cooperative’s (SFNMC) efforts in testing methyl bromide (MBr) alternatives for soil fumigation. In the southeastern United States, fumigation with MBr has been the most commonly used method for producing high quality, pest-free forest-tree seedlings in an environment that is conducive for soil-...

BAG PASSOUT SEALER FOR WATER-SHIELDED CAVE FACILITY (Engineering Materials)

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1963-10-31

The water-shielded cave facility is used in processing irradiated slugs for recovery of americium, curium, berkelium, californium, einsteinium, and fermium. The remotely operated, plastic-bag passout sealer is used in removing isotopic fractions for storage in the rear or for removing radioactive waste for placement in the waste storage containers. The unit is accessible by both the primary inclosure master-slaves and the service area master-slaves. (F.L.S.)

Bromidotetra-kis-(1H-2-ethyl-5-methyl-imidazole-κN)copper(II) bromide.

PubMed

Godlewska, Sylwia; Baranowska, Katarzyna; Socha, Joanna; Dołęga, Anna

2011-12-01

The Cu(II) ion in the title compound, [CuBr(C(6)H(10)N(2))(4)]Br, is coordinated in a square-based-pyramidal geometry by the N atoms of four imidazole ligands and a bromide anion in the apical site. Both the Cu(II) and Br(-) atoms lie on a crystallographic fourfold axis. In the crystal, the [CuBr(C(6)H(10)N(2))(4)](+) complex cations are linked to the uncoordinated Br(-) anions (site symmetry [Formula: see text]) by N-H⋯Br hydrogen bonds, generating a three-dimensional network. The ethyl group of the imidazole ligand was modelled as disordered over two orientations with occupancies of 0.620 (8) and 0.380 (8).

Assessment of the Mutagenic Potential of Carbon Disulfide, Carbon Tetrachloride, Dichloromethane, Ethylene Dichloride, and Methyl Bromide: A Comparative Analysis in Relation to Ethylene Dibromide

EPA Science Inventory

The document provides an evaluation of the mutagenic potential of five alternative fumigants to ethylene dibromide(EDB). These include carbon disulfide(CS2), carbon tetrachloride(CCl4), dichloromethane(DCM), ethylene dichloride(EDC), and methyl bromide (MB). Of the five proposed ...

A comparison between a combination of ipratropium bromide plus fenoterol in a single metered dose inhaler (Duovent) and salbutamol in asthma.

PubMed Central

Flint, K. C.; Hockley, B.; Johnson, N. M.

1983-01-01

The efficacy of a single metered dose inhaler containing a combination of fenoterol (100 micrograms/puff) and ipratropium bromide (40 micrograms/puff) has been assessed in 12 asthmatics. We conclude that the bronchodilator effect of 2 puffs of the combination inhaler was significantly greater than that achieved by 2 puffs of salbutamol (100 micrograms/puff). PMID:6227877

Bis(2,2′-bipyridyl-κ2 N,N′)(carbonato-κ2 O,O′)cobalt(III) bromide trihydrate

PubMed Central

Ma, Peng-Tao; Wang, Yu-Xia; Zhang, Guo-Qian; Li, Ming-Xue

2008-01-01

The title complex, [Co(CO3)(C10H8N2)2]Br·3H2O, is isostructural with the chloride analogue. The six-coordinated octahedral [Co(2,2′-bipy)2CO3]+ cation (2,2′-bipy is 2,2′-bipyrid­yl), bromide ion and water mol­ecules are linked together via O—H⋯Br and O—H⋯O hydrogen bonds, generating a one-dimensional chain. PMID:21200495

Bacterial oxidation of methyl bromide in Mono Lake, California

USGS Publications Warehouse

Connell, T.L.; Joye, S.B.; Miller, L.G.; Oremland, R.S.

1997-01-01

The oxidation of methyl bromide (MeBr) in the water column of Mono Lake, CA, was studied by measuring the formation of H14CO3 from [14C]MeBr. Potential oxidation was detected throughout the water column, with highest rates occurring in the epilimnion (5-12 m depth). The oxidation of MeBr was eliminated by filter-sterilization, thereby demonstrating the involvement of bacteria. Vertical profiles of MeBr activity differed from those obtained for nitrification and methane oxidation, indicating that MeBr oxidation is not simply a co-oxidation process by either nitrifiers or methanotrophs. Furthermore, specific inhibitors of methane oxidation and/or nitrification (e.g., methyl fluoride, acetylene, allyl sulfide) had no effect upon the rate of MeBr oxidation in live samples. Of a variety of potential electron donors added to Mono Lake water, only trimethylamine resulted in the stimulation of MeBr oxidation. Cumulatively, these results suggest that the oxidation of MeBr in Mono Lake waters is attributable to trimethylamine-degrading methylotrophs. Neither methyl chloride nor methanol inhibited the oxidation of [14C]MeBr in live samples, indicating that these bacteria directly oxidized MeBr rather than the products of MeBr nucleophilic substitution reactions.

Pharmacological and non-pharmacological interventions for reducing rocuronium bromide induced pain on injection in children and adults.

PubMed

Prabhakar, Hemanshu; Singh, Gyaninder Pal; Ali, Zulfiqar; Kalaivani, Mani; Smith, Martha A

2016-02-12

Rocuronium bromide is a routinely used muscle relaxant in anaesthetic practice. Its use, however, is associated with intense pain on injection. While it is well established that rocuronium bromide injection causes pain in awake patients, anaesthetized patients also tend to show withdrawal movements of the limbs when this muscle relaxant is administered. Various strategies, both pharmacological and non-pharmacological, have been studied to reduce the incidence and severity of pain on rocuronium bromide injection. We wanted to find out which of the existing modalities was best to reduce pain on rocuronium injection. The objectives of this review were to assess the ability of both pharmacological and non-pharmacological interventions to reduce or eliminate the pain that accompanies rocuronium bromide administration. We searched the Cochrane Central Register of Controlled Trials (CENTRAL 2013, Issue 7), MEDLINE via Ovid SP (1966 to July 2013) and EMBASE via Ovid SP (1980 to July 2013). We also searched specific websites. We reran the searches in February 2015 and will deal with the 11 studies of interest found through this search when we update the review. We included all randomized controlled trials (RCTs) that compared the use of any drug or a non-pharmacological method with control patients, or those receiving no treatment to reduce the severity of pain with rocuronium injection. Our primary outcome was pain on rocuronium bromide injection measured by a pain score assessment. Our secondary outcomes were rise in heart rate and blood pressure following administration of rocuronium and adverse events related to the interventions. We used the standardized methods for conducting a systematic review as described in the Cochrane Handbook for Systematic Reviews of Interventions. Two authors independently extracted details of trial methodology and outcome data from reports of all trials considered eligible for inclusion. We made all analyses on an intention-to-treat basis

Effect on Ammonium Bromide in dielectric behavior based Alginate Solid Biopolymer electrolytes

NASA Astrophysics Data System (ADS)

Fuzlin, A. F.; Rasali, N. M. J.; Samsudin, A. S.

2018-04-01

This paper present the development of solid biopolymer electrolytes (SBEs) system which has been accomplished by incorporating various composition of ionic dopant namely ammonium bromide (NH4Br) with alginate solution casting method. The prepared sample of SBEs has been analyzed via electrical impedance spectroscopy (EIS) showed that the ionic conductivity at room temperature was increased from 4.67 x 10-7 S cm-1 for un-doped sample to optimum value at 4.41 x 10-5 S cm-1 for composition of 20 wt. % NH4Br. The SBEs system was found to obey the Arrhenius characteristics with R2~1where all sample is thermally activated when increasing temperature. The dielectric behavior of the alginate-NH4Br SBEs system were measured using complex permittivity (ε*) and complex electrical modulus (M*) and shown the non-debye behavior where no single relaxation was found for present SBEs system.

Potential impacts of imposing methyl bromide phaseout on US strawberry growers: a case study of a nomination for a critical use exemption under the Montreal Protocol.

PubMed

Norman, Catherine S

2005-04-01

The Montreal Protocol on Substances that Deplete the Ozone Layer requires developed countries to phaseout methyl bromide production and non-quarantine uses by 2005 and developing countries to do the same by 2015. Exemptions to phaseout have been significant in slowing the process of abatement; many countries have applied for exemptions for some uses, partly on grounds that phaseout is economically infeasible. Data on the US strawberry market are used to investigate grower costs arising from substitution away from methyl bromide, the impact of trends in and characteristics of the demand for fresh strawberries, and characteristics of trade with countries not yet required to eliminate use of the compound. It appears that actual net costs to growers will be much smaller than the simple increase in production costs cited in the US nomination for exemption.

Bromide, Chloride, and Sulfate Concentrations and Loads at U.S. Geological Survey Streamflow-Gaging Stations 07331600 Red River at Denison Dam, 07335500 Red River at Arthur City, and 07336820 Red River near DeKalb, Texas, 2007-09

USGS Publications Warehouse

Baldys, Stanley; Churchill, Christopher J.; Mobley, Craig A.; Coffman, David K.

2010-01-01

The U.S. Geological Survey, in cooperation with the City of Dallas Water Utilities Division, did a study to characterize bromide, chloride, and sulfate concentrations and loads at three U.S. Geological Survey streamflow-gaging stations on the reach of the Red River from Denison Dam, which impounds Lake Texoma, to the U.S. Highway 259 bridge near DeKalb, Texas. Bromide, chloride, and sulfate concentrations and loads were computed for streamflow-gaging stations on the study reach of the Red River. Continuous streamflow and specific conductance data and discrete samples for bromide, chloride, sulfate, and specific conductance were collected at three main-stem streamflow-gaging stations on the Red River: 07331600 Red River at Denison Dam near Denison, Texas (Denison Dam gage), 07335500 Red River at Arthur City, Texas (Arthur City gage), and 07336820 Red River near DeKalb, Texas (DeKalb gage). At each of these streamflow-gaging stations, discrete water-quality data were collected during January 2007-February 2009; continuous water-quality data were collected during March 2007-February 2009. Two periods of high flow resulted from floods during the study; floods during June-July 2007 resulted in elevated flow during June-September 2007 and smaller floods during March-April 2008 resulted in elevated flow during March-April 2008. Bromide, chloride, and sulfate concentrations in samples collected at the three gages decreased downstream. Median bromide concentrations ranged from 0.32 milligram per liter at the Denison Dam gage to 0.19 milligram per liter at the DeKalb gage. Median chloride concentrations ranged from 176 milligrams per liter at the Denison Dam gage to 108 milligrams per liter at the DeKalb gage, less than the 300-milligrams per liter secondary maximum contaminant level established by the Texas Commission on Environmental Quality. Median sulfate concentrations ranged from 213 milligrams per liter at the Denison Dam gage to 117 milligrams per liter at the De

Process analysis and economics of drinking water production from coastal aquifers containing chromophoric dissolved organic matter and bromide using nanofiltration and ozonation.

PubMed

Sobhani, R; McVicker, R; Spangenberg, C; Rosso, D

2012-01-01

In regions characterized by water scarcity, such as coastal Southern California, groundwater containing chromophoric dissolved organic matter is a viable source of water supply. In the coastal aquifer of Orange County in California, seawater intrusion driven by coastal groundwater pumping increased the concentration of bromide in extracted groundwater from 0.4 mg l⁻¹ in 2000 to over 0.8 mg l⁻¹ in 2004. Bromide, a precursor to bromate formation is regulated by USEPA and the California Department of Health as a potential carcinogen and therefore must be reduced to a level below 10 μg l⁻¹. This paper compares two processes for treatment of highly coloured groundwater: nanofiltration and ozone injection coupled with biologically activated carbon. The requirement for bromate removal decreased the water production in the ozonation process to compensate for increased maintenance requirements, and required the adoption of catalytic carbon with associated increase in capital and operating costs per unit volume. However, due to the absence of oxidant addition in nanofiltration processes, this process is not affected by bromide. We performed a process analysis and a comparative economic analysis of capital and operating costs for both technologies. Our results show that for the case studied in coastal Southern California, nanofiltration has higher throughput and lower specific capital and operating cost, when compared to ozone injection with biologically activate carbon. Ozone injection with biologically activated carbon, compared to nanofiltration, has 14% higher capital cost and 12% higher operating costs per unit water produced while operating at the initial throughput. Due to reduced ozone concentration required to accommodate for bromate reduction, the ozonation process throughput is reduced and the actual cost increase (per unit water produced) is 68% higher for capital cost and 30% higher for operations. Copyright © 2011 Elsevier Ltd. All rights reserved.

Competition between organics and bromide at the aqueous solution-air interface as seen from ozone uptake kinetics and X-ray photoelectron spectroscopy.

PubMed

Lee, Ming-Tao; Brown, Matthew A; Kato, Shunsuke; Kleibert, Armin; Türler, Andreas; Ammann, Markus

2015-05-14

A more detailed understanding of the heterogeneous chemistry of halogenated species in the marine boundary layer is required. Here, we studied the reaction of ozone (O3) with NaBr solutions in the presence and absence of citric acid (C6H8O7) under ambient conditions. Citric acid is used as a proxy for oxidized organic material present at the ocean surface or in sea spray aerosol. On neat NaBr solutions, the observed kinetics is consistent with bulk reaction-limited uptake, and a second-order rate constant for the reaction of O3 + Br(-) is 57 ± 10 M(-1) s(-1). On mixed NaBr-citric acid aqueous solutions, the uptake kinetics was faster than that predicted by bulk reaction-limited uptake and also faster than expected based on an acid-catalyzed mechanism. X-ray photoelectron spectroscopy (XPS) on a liquid microjet of the same solutions at 1.0 × 10(-3)-1.0 × 10(-4) mbar was used to obtain quantitative insight into the interfacial composition relative to that of the bulk solutions. It revealed that the bromide anion becomes depleted by 30 ± 10% while the sodium cation gets enhanced by 40 ± 20% at the aqueous solution-air interface of a 0.12 M NaBr solution mixed with 2.5 M citric acid in the bulk, attributed to the role of citric acid as a weak surfactant. Therefore, the enhanced reactivity of bromide solutions observed in the presence of citric acid is not necessarily attributable to a surface reaction but could also result from an increased solubility of ozone at higher citric acid concentrations. Whether the acid-catalyzed chemistry may have a larger effect on the surface than in the bulk to offset the effect of bromide depletion also remains open.

Performance limiting processes in room temperature thallium bromide radiation detectors

NASA Astrophysics Data System (ADS)

Datta, Amlan; Becla, Piotr; Moed, Demi; Motakef, Shariar

2015-09-01

Thallium Bromide (TlBr) is a promising room-temperature radiation detector candidate with excellent charge transport properties. However, several critical issues are needed to be addressed before deployment of this material for long-term field applications. In this paper, the relevance and, scientific and technological progress made towards solving these challenges for TlBr have been discussed. The possible research pathways to mitigate the concerns related to this material have been analyzed and clearly established. Findings from novel experiments performed at CapeSym have revealed that the most significant factors for achieving long-term performance stability for TlBr devices involve physical and chemical conditions of the surface, residual stress, and choice of metal contacts. Palladium electrodes on TlBr devices resulted in a 20-fold improvement in the device lifetime when compared to its Br-etched Pt counterpart. Electron and hole contributions towards the spectroscopic response of the TlBr detector significantly depend on the interaction position of the incoming radiation and was clearly observed in this study. TlBr device fabrication techniques need significant improvement in order to attain reliable, repeatable, and stable, long-term performance.

Nanocapsules of perfluorooctyl bromide for theranostics: from formulation to targeting

NASA Astrophysics Data System (ADS)

Diou, O.; Fattal, E.; Payen, T.; Bridal, S. L.; Valette, J.; Tsapis, N.

2014-03-01

The need to detect cancer at its early stages, as well as, to deliver chemotherapy to targeted site motivates many researchers to build theranostic platforms which combine diagnostic and therapy. Among imaging modalities, ultrasonography and Magnetic Resonance Imaging (MRI) are widely available, non invasive and complement each other. Both techniques often require the use of contrast agents. We have developed nanocapsules of perfluorooctyl bromide as dual contrast agent for both imaging modalities. The soft, amorphous polymer shell provides echogenicity, while the high-density perfluorinated liquid core allows detection by 19F MRI. We have used a shell of poly(lactide-co-glycolide) (PLGA) since this polymer is biodegradable, biocompatible and can be loaded with drugs. These capsules were shown to be efficient in vitro as contrast agents for both 19F MRI and ultrasonography. In addition, for in vivo applications a poly(ethyleneglycol) (PEG) coating promotes stability and prolonged circulation. Being stealth, nanocapsule can accumulate passively into implanted tumors by the EPR effect. We will present nanocapsule formulation and characterization, and will show promising in vivo results obtained for both ultrasonography and 19F MRI.

Charge trapping in detector grade thallium bromide and cadmium zinc telluride: Measurement and theory

NASA Astrophysics Data System (ADS)

Elshazly, Ezzat S.; Tepper, Gary; Burger, Arnold

2010-08-01

Carrier trapping times were measured in detector grade thallium bromide (TlBr) and cadmium zinc telluride (CZT) from 300 to 110 K and the experimental data were analyzed using a trapping model. In CZT, because the majority carrier concentration is close to the intrinsic carrier concentration, the trapping time increases exponentially as the temperature decreases below about 160 K. In TlBr, the majority carrier concentration is many orders of magnitude greater than the intrinsic carrier concentration and the trapping time followed a (1/ T) 1/2 temperature dependence over the range of temperatures studied. The results of the model suggest that a moderately deep compensation center could be used to significantly increase the room temperature trapping time in TlBr.

Growth and characterization of Cadmium Thiosemicarbazide Bromide crystals for antibacterial and nonlinear optical applications

NASA Astrophysics Data System (ADS)

Thomas Joseph Prakash, J.; Martin Sam Gnanaraj, J.

2015-01-01

Semiorganic nonlinear optical crystals of Cadmium Thiosemicarbazide Bromide was grown by slow evaporation solution growth technique. The unit cell parameters were estimated by subjecting the crystals to single crystal X-ray diffraction. The grown crystals were subjected to Powder X-ray diffraction for analyzing the crystalline nature of the sample. FTIR studies reveal the functional groups and the optical characters were analyzed by UV-Vis spectral studies. Mechanical stability of the sample was assessed by Vicker's micro hardness test. The presence of surface dislocations was identified by chemical etching technique. Antibacterial study was carried out against ACDP declared harmful pathogens. SHG efficiency of CTSB crystal was tested using Nd: YAG laser and it was found to be ∼1.8 times that of potassium dihydrogen phosphate.

MAPbI2.9-xBrxCl0.1 hybrid halide perovskites: Shedding light on the effect of chloride and bromide ions on structural and photoluminescence properties

NASA Astrophysics Data System (ADS)

Atourki, Lahoucine; Vega, Erika; Marí, Bernabé; Mollar, Miguel; Ait Ahsaine, Hassan; Bouabid, Khalid; Ihlal, Ahmed

2016-12-01

The optical and structural properties of CH3NH3PbI3 can be adjusted by introducing other extrinsic ions such as chloride and bromide. In this work, mixed bromide iodide lead perovskites with a 10% fraction of chloride were prepared from methylamine, lead nitrate and the corresponding hydro acid (X = I, Br, Cl). The effect of bromide and chloride incorporation on different properties of perovskite thin film was investigated. The Pawley fit method indicates the formation of the iodide halide MAPbI3 Pm-3 m cubic phase for x = 0 and the tetragonal P4/mmm phase for x ≥ 0.3. All deposited films showed a strong absorbance in the UV-vis range. The band gap values were estimated from absorbance measurements. It was found that the onset of the absorption edge for MAPbI2.9-xBrxCl0.1 thin film perovskites ranges between 1.60 and 1.80 eV. Moreover, it was found that both Cl and Br affect the PL emission of the mixed halide lead perovskite, the MAPbI2.9-xBrxCl0.1 films displayed intermediate values from 730 nm (MAPbI2.2Br0.7Cl0.1) to 770 nm (MAPbI2.6Br0.3Cl0.1).

Analysis of Te and TeO 2 on CdZnTe Nuclear Detectors Treated with Hydrogen Bromide and Ammonium-Based Solutions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Drabo, Mebougna L.; Egarievwe, Stephen U.; Okwechime, Ifechukwude O.

Surface defects caused during cutting and polishing in the fabrication of cadmium zinc telluride (CdZnTe) nuclear detectors limit their spectral performance. Chemical treatments are often used to remove surface damages and defects. In this paper, we present the analysis of Te and TeO 2 species on the surfaces of CdZnTe nuclear detectors treated with hydrogen bromide and ammonium-based solutions. The CdZnTe wafers were chemo-mechanically polished in a mixture of hydrogen bromide in hydrogen peroxide and ethylene glycol, followed by a chemical passivation in a mixture of ammonium fluoride and hydrogen peroxide solution. X-ray photoelectron spectroscopy showed significant conversion of Temore » to TeO 2, thus producing a more chemically stable surface. The resistivity of the CdZnTe samples is in the order of 1010 ohms-cm. The current for a given applied voltage increased following the passivation and decreased after a 3-hour period. Results from spectral response measurements showed that the 59.5-keV gamma-peak of Am-241 was stable under the same channel for the surface treatment processes.« less

Interfacial concentrations of chloride and bromide in zwitterionic micelles with opposite dipoles: experimental determination by chemical trapping and a theoretical description.

PubMed

de Souza, Tereza Pereira; Chaimovich, Hernan; Fahr, Alfred; Schweitzer, Bianca; Agostinho Neto, Augusto; Cuccovia, Iolanda Midea

2012-04-01

Interfacial concentrations of chloride and bromide ions, with Li(+), Na(+), K(+), Rb(+), Cs(+), trimethylammonium (TMA(+)), Ca(2+), and Mg(2+) as counterions, were determined by chemical trapping in micelles formed by two zwitterionic surfactants, namely N-hexadecyl-N,N-dimethyl-3-ammonio-1-propanesulfonate (HPS) and hexadecylphosphorylcholine (HDPC) micelles. Appropriate standard curves for the chemical trapping method were obtained by measuring the product yields of chloride and bromide salts with 2,4,6-trimethyl-benzenediazonium (BF(4)) in the presence of low molecular analogs (N,N,N-trimethyl-propane sulfonate and methyl-phosphorylcholine) of the employed surfactants. The experimentally determined values for the local Br(-) (Cl(-)) concentrations were modeled by fully integrated non-linear Poisson Boltzmann equations. The best fits to all experimental data were obtained by considering that ions at the interface are not fixed at an adsorption site but are free to move in the interfacial plane. In addition, the calculation of ion distribution allowed the estimation of the degree of ion coverage by using standard chemical potential differences accounting for ion specificity. Copyright © 2012 Elsevier Inc. All rights reserved.

Analysis of Te and TeO 2 on CdZnTe Nuclear Detectors Treated with Hydrogen Bromide and Ammonium-Based Solutions

DOE PAGES

Drabo, Mebougna L.; Egarievwe, Stephen U.; Okwechime, Ifechukwude O.; ...

2017-04-30

Surface defects caused during cutting and polishing in the fabrication of cadmium zinc telluride (CdZnTe) nuclear detectors limit their spectral performance. Chemical treatments are often used to remove surface damages and defects. In this paper, we present the analysis of Te and TeO 2 species on the surfaces of CdZnTe nuclear detectors treated with hydrogen bromide and ammonium-based solutions. The CdZnTe wafers were chemo-mechanically polished in a mixture of hydrogen bromide in hydrogen peroxide and ethylene glycol, followed by a chemical passivation in a mixture of ammonium fluoride and hydrogen peroxide solution. X-ray photoelectron spectroscopy showed significant conversion of Temore » to TeO 2, thus producing a more chemically stable surface. The resistivity of the CdZnTe samples is in the order of 1010 ohms-cm. The current for a given applied voltage increased following the passivation and decreased after a 3-hour period. Results from spectral response measurements showed that the 59.5-keV gamma-peak of Am-241 was stable under the same channel for the surface treatment processes.« less

Experimental and theoretical characterization of organic salt: 2-((4-bromophenyl)amino) pyrido[1,2-a] quinoxalin-11-ium bromide monohydrate synthesized via oxidative cyclization

NASA Astrophysics Data System (ADS)

Faizi, Md. Serajul Haque; Alam, Mohammad Jane; Haque, Ashanul; Ahmad, Shabbir; Shahid, M.; Ahmad, Musheer

2018-03-01

Quinoxalines are nitrogen-embedded heterocyclic compounds that possess unique and versatile pharmacological applications. The present article describes synthesis and characterization of organic salt 2-((4-bromophenyl)amino)pyrido [1,2-a]quinoxalin-11-ium bromide (BAPQ), an oxidative cyclized product of N-phenyl-N-(pyridine-2-ylmethylene)benzene-1,4-diamine (PPMD). The structure of the synthesized product was extensively characterized by 1H NMR, 2D-COSY NMR, MS, IR, UV-vis, X-ray techniques and elemental analysis. The electronic and structural properties of BAPQ was well complemented by performing extensive computational studies (B3LYP/6-311G (d,p) basis sets). Metal-free, mild reaction condition, easy work-up and excellent yield with high purity are main features of this work and thus holds promise for the generation of new compounds of this class. Analytical results indicated ionic nature of the compound with bromide as counterion. DFT calculation showed low kinetic stability and high reactivity of the compound.

Ion transport properties of magnesium bromide/dimethyl sulfoxide non-aqueous liquid electrolyte

PubMed Central

Sheha, E.

2015-01-01

Nonaqueous liquid electrolyte system based dimethyl sulfoxide DMSO and magnesium bromide (MgBr2) is synthesized via ‘Solvent-in-Salt’ method for the application in magnesium battery. Optimized composition of MgBr2/DMSO electrolyte exhibits high ionic conductivity of 10−2 S/cm at ambient temperature. This study discusses different concentrations from 0 to 5.4 M of magnesium salt, representing low, intermediate and high concentrations of magnesium salt which are examined in frequency dependence conductivity studies. The temperature dependent conductivity measurements have also been carried out to compute activation energy (Ea) by least square linear fitting of Arrhenius plot: ‘log σ − 1/T. The transport number of Mg2+ ion determined by means of a combination of d.c. and a.c. techniques is ∼0.7. A prototype cell was constructed using nonaqueous liquid electrolyte with Mg anode and graphite cathode. The Mg/graphite cell shows promising cycling. PMID:26843967

An effective method for thallium bromide purification and research on crystal properties

NASA Astrophysics Data System (ADS)

Zheng, Zhiping; Meng, Fang; Gong, Shuping; Quan, Lin; Wang, Jing; Zhou, Dongxiang

2012-06-01

Thallium bromide (TlBr) is a promising candidate for room-temperature X- and gamma-ray detectors in view of its excellent intrinsic features. However, material purity and crystal quality concerns still limit the use of TlBr crystals as detectors. In this work, a combination of hydrothermal recrystallization (HR) and vacuum distillation (VD) methods were applied to purify TlBr salts prior to crystal growth. Trace impurities at the ppb/ppm level were determined by inductively coupled plasma mass spectroscopy (ICP-MS). The results showed that the impurity concentrations of the TlBr salt decreased significantly after HR and VD purification, and high performance of the resultant TlBr crystal in areas such as electrical and optical properties was achieved. The combination of HR and VD methods could fabricate purer material, with an order of magnitude higher resistivity and better optical quality, than HR or VD method used separately. The possible technological considerations affecting the parameters of the crystals are investigated.

Continued development of thallium bromide and related compounds for gamma-ray spectrometers

NASA Astrophysics Data System (ADS)

Kim, H.; Churilov, A.; Ciampi, G.; Cirignano, L.; Higgins, W.; Kim, S.; O'Dougherty, P.; Olschner, F.; Shah, Kanai

2011-02-01

Thallium bromide (TlBr) and related ternary compounds, TlBrI and TlBrCl, have been under development for room temperature gamma-ray spectroscopy due to high density, high Z and wide bandgap of the material. Low melting point and cubic crystal structure of selected compositions of these compounds facilitate crystal growth by melt techniques. Recent advances in material purification, crystal growth, and device processing have led to mobility-lifetime products of electrons in the mid 10 -3 cm 2/V range enabling working detectors of greater than 15 mm thickness to be fabricated. In this paper we report on our recent progress on TlBr detector development and first results from TlBr xCl 1- x devices. Pulse height spectra will be presented from TlBr arrays as thick as 18 mm. Depth corrected spectra will also be presented. For a 5 mm thick TlBr array, energy resolution of less than 1% (FWHM at 662 keV) was obtained after depth correction.

Resonance light scattering technique for the determination of protein with rutin and cetylpyridine bromide system.

PubMed

Liu, Yang; Yang, Jinghe; Liu, Shufang; Wu, Xia; Su, Benyu; Wu, Tao

2005-02-01

A new resonance light scattering (RLS) assay of protein is presented. In Tris-NaOH (pH = 10.93) buffer, the RLS of rutin-cetylpyridine bromide (CPB) system can be greatly enhanced by protein, including bovine serum albumin (BSA) and human serum albumin (HSA). The enhanced RLS intensities are in proportion to the concentration of proteins in the range of 5 x 10(-9) to 2.5 x 10(-6) g ml(-1) for BSA and 2.5 x 10(-8) to 3.5 x 10(-6) g ml(-1) for HSA. The detection limits (S/N = 3) are 3.0 ng ml(-1) for BSA and 10.0 ng ml(-1) for HSA. Samples are determined satisfactorily.

Selenium containing imidazolium salt in designing single source precursors for silver bromide and selenide nano-particles.

PubMed

Joshi, Hemant; Sharma, Kamal Nayan; Singh, Ved Vati; Singh, Pradhumn; Singh, Ajai Kumar

2013-02-21

The AgBr and Ag(2)Se nanoparticles (NPs) have been synthesized for the first time from two single source precursors ([Ag(2)(L)(2)Br(2)] (1) and [Ag(L-HBr)(2)]BF(4) (2) respectively) designed using the same ligand 3-benzyl-1-(2-phenylselanyl-ethyl)-3H-imidazolium bromide (L). The ODE-ODA-OA (1 : 1 : 2) and TOP-OA (1 : 2) are most suitable solvents for thermolysis of 1 and 2 respectively, resulting in the NPs. The composition of the solvent used in thermolysis affects the purity of NPs. The bonding of L in 1 is unique, as it has a pre-carbene site intact.

The effect of silver on the optical, spectral-luminescent, and crystallization properties of bromide photo-thermo-refractive glasses

NASA Astrophysics Data System (ADS)

Oreshkina, K. V.; Dubrovin, V. D.; Ignat'ev, A. I.; Nikonorov, N. V.

2017-10-01

The effect of silver on the optical, spectral-luminescent, and crystallization properties of bromide photo-thermo-refractive glasses is studied. Multicomponent photosensitive glasses of the Na2O-ZnO-Al2O3-SiO2 system with photosensitizing agents (cerium, antimony, silver) and halogenides (fluorine and bromine) are synthesized. Ultraviolet irradiation and thermal treatment below the glass-transition temperature of the glasses cause the formation of silver molecular clusters, which exhibit luminescence in the visible and infrared regions. UV irradiation and thermal treatment of glasses above the glass-transition temperature lead to the growth of silver nanoparticles with plasmon resonance peak in the region of 420 nm. Further thermal treatment of glasses above the glass-transition temperature shifts the plasmon-resonance maximum by 70 nm to longer wavelengths, which is related to the growth of a crystalline shell consisting of mixed silver and sodium bromides on nanoparticles. This formation of a crystalline phase on colloidal centers results in a local increase in the refractive index of the irradiated region by +Δ n 900 ppm compared to the nonirradiated region. Photo-thermo-refractive glasses with increased silver concentration are promising photosensitive materials for creating holographic optical elements and devices for line narrowing and stabilizing filters, spectral beam combiners, and filters for increasing the spectral brightness of laser diodes. A positive change in the refractive index of Photo-thermo-refractive glasses provides the possibility of recording in them 3D waveguide and integrated-optical structures.

Inhalable Ipratropium Bromide Particle Engineering with Multicriteria Optimization.

PubMed

Vinjamuri, Bhavani Prasad; Haware, Rahul V; Stagner, William C

2017-08-01

Spray-dried ipratropium bromide (IPB) microspheres for oral inhalation were engineered using Quality by Design. The interrogation of material properties, process parameters, and critical product quality attributes interplay enabled rational product design. A 2 7-3 screening design exhibited the Maillard reaction between L-leucine (LL) and lactose at studied outlet temperatures (OT) >130°C. A response surface custom design was used in conjunction with multicriteria optimization to determine the operating design space to achieve inhalable microparticles. Statistically significant predictive models were developed for volume median diameter (p = 0.0001, adjusted R 2   = 0.9938), span (p = 0.0278, adjusted R 2   = 0.7912), yield (p = 0.0020, adjusted R 2   = 0.9320), and OT (p = 0.0082, adjusted R 2   = 0.8768). An independent verification batch confirmed the model's predictive capability. The prediction and actual values were in good agreement. Particle size and span were 3.32 ± 0.09 μm and 1.71 ± 0.18, which were 4.7 and 5.3% higher than the predicted values. The process yield was 50.3%, compared to the predicted value of 65.3%. The OT was 100°C versus the predicted value of 105°C. The label strength of IPB microparticles was 99.0 to 105.9% w/w suggesting that enrichment occurred during the spray-drying process. The present study can be utilized to initiate the design of the first commercial IPB dry powder inhaler.

Stable room-temperature thallium bromide semiconductor radiation detectors

NASA Astrophysics Data System (ADS)

Datta, A.; Fiala, J.; Becla, P.; Motakef, Shariar

2017-10-01

Thallium bromide (TlBr) is a highly efficient ionic semiconductor with excellent radiation detection properties. However, at room temperature, TlBr devices polarize under an applied electric field. This phenomenon not only degrades the charge collection efficiency of the detectors but also promotes chemical reaction of the metal electrodes with bromine, resulting in an unstable electric field and premature failure of the device. This drawback has been crippling the TlBr semiconductor radiation detector technology over the past few decades. In this exhaustive study, this polarization phenomenon has been counteracted using innovative bias polarity switching schemes. Here the highly mobile Br- species, with an estimated electro-diffusion velocity of 10-8 cm/s, face opposing electro-migration forces during every polarity switch. This minimizes the device polarization and availability of Br- ions near the metal electrode. Our results indicate that it is possible to achieve longer device lifetimes spanning more than 17 000 h (five years of 8 × 7 operation) for planar and pixelated radiation detectors using this technique. On the other hand, at constant bias, 2500 h is the longest reported lifetime with most devices less than 1000 h. After testing several biasing switching schemes, it is concluded that the critical bias switching frequency at an applied bias of 1000 V/cm is about 17 μHz. Using this groundbreaking result, it will now be possible to deploy this highly efficient room temperature semiconductor material for field applications in homeland security, medical imaging, and physics research.

Ammonia-hydrogen bromide and ammonia-hydrogen iodide complexes: anion photoelectron and ab initio studies.

PubMed

Eustis, S N; Whiteside, A; Wang, D; Gutowski, M; Bowen, K H

2010-01-28

The ammonia-hydrogen bromide and ammonia-hydrogen iodide, anionic heterodimers were studied by anion photoelectron spectroscopy. In complementary studies, these anions and their neutral counterparts were also investigated via ab initio theory at the coupled cluster level. In both systems, neutral NH(3)...HX dimers were predicted to be linear, hydrogen-bonded complexes, whereas their anionic dimers were found to be proton-transferred species of the form, (NH(4)(+)X(-))(-). Both experimentally measured and theoretically predicted vertical detachment energies (VDE) are in excellent agreement for both systems, with values for (NH(4)(+)Br(-))(-) being 0.65 and 0.67 eV, respectively, and values for (NH(4)(+)I(-))(-) being 0.77 and 0.81 eV, respectively. These systems are discussed in terms of our previous study of (NH(4)(+)Cl(-))(-).

Characterization of potassium bromide crystals grown in the aqueous solution of picric acid

NASA Astrophysics Data System (ADS)

Maheswari, J. Uma; Krishnan, C.; Kalyanaraman, S.; Selvarajan, P.

2016-12-01

Potassium bromide crystals were grown in the aqueous solution of picric acid by slow evaporation technique at room temperature. X-ray Diffraction (XRD) analysis ensures that the grown sample is in Fm3m space group and FCC structure. Energy Dispersive X-ray Spectroscopy (EDX) reveals the presence of elements in the title compound. UV-Vis-NIR spectrum reveals that the grown sample is a promising nonlinear optical (NLO) material. FTIR analysis confirms the functional groups present in the sample. The thermogravimetric (TG) and differential thermogravimetric (DTA) analyses ensure that the sample material is thermally stable up to 160 °C. The second harmonic efficiency of the sample is 1.3 times greater than that of standard KDP. The mechanical strength of the grown sample is estimated by Vickers microhardness tester. The electrical properties were investigated by impedance analysis and the results of various studies of the grown crystals are discussed.

Effect of Sodium Dodecyl Sulphate and Sodium Bromide Additives on Ni–W Nanocoatings.

PubMed

Das, Malay Kumar; Qin, Jiaqian; Zhang, Xinyu; Li, Rongxia; Thueploy, Adisak; Limpanart, Sarintorn; Boonyongmaneerat, Yuttanat; Ma, Mingzhen; Liu, Riping

2017-02-01

Nickel-tungsten (Ni–W) coatings were fabricated by electrodeposition method with varying quantities of sodium dodecyl sulphate and sodium bromide to examine the effects of the aforesaid additives on the coatings. The obtained nanocoatings were studied by X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy, and hardness tester. The hardness, tungsten content and grain size attained a maximum value at current density of 0.15 A/cm²,0.1 A/cm² and 0.1 A/cm², respectively. There was a pronounced impact of both the additives on the microstructure and morphology of the coatings. According to results, there are considerable difference in terms of the impact caused by the additives to the tungsten content, hardness and grain size of the coatings. The obtained results suggest that hardness of coatings is mainly contributed by W content in the deposits.

Handbook of Basic Atomic Spectroscopic Data

National Institute of Standards and Technology Data Gateway

SRD 108 Handbook of Basic Atomic Spectroscopic Data (Web, free access)   This handbook provides a selection of the most important and frequently used atomic spectroscopic data. The compilation includes data for the neutral and singly-ionized atoms of all elements hydrogen through einsteinium (Z = 1-99). The wavelengths, intensities, and spectrum assignments are given for each element, and the data for the approximately 12,000 lines of all elements are also collected into a single table.

Activated carbons from end-products of tree nut and tree fruit production as sorbents for removing methyl bromide in ventilation effluent from postharvest chamber fumigation

USDA-ARS?s Scientific Manuscript database

End-products of tree nuts and tree fruits grown in California, USA were evaluated for the ability to remove methyl bromide from the ventilation effluent of postharvest chamber fumigations. Activated carbon sorbents from walnut and almond shells as well as peach and prune pits were prepared using dif...

A combined solid-state NMR and X-ray crystallography study of the bromide ion environments in triphenylphosphonium bromides.

PubMed

Burgess, Kevin M N; Korobkov, Ilia; Bryce, David L

2012-04-27

Multinuclear ((31)P and (79/81)Br), multifield (9.4, 11.75, and 21.1 T) solid-state nuclear magnetic resonance experiments are performed for seven phosphonium bromides bearing the triphenylphosphonium cation, a molecular scaffold found in many applications in chemistry. This is undertaken to fully characterise their bromine electric field gradient (EFG) tensors, as well as the chemical shift (CS) tensors of both the halogen and the phosphorus nuclei, providing a rare and novel insight into the local electronic environments surrounding them. New crystal structures, obtained from single-crystal X-ray diffraction, are reported for six compounds to aid in the interpretation of the NMR data. Among them is a new structure of BrPPh(4), because the previously reported one was inconsistent with our magnetic resonance data, thereby demonstrating how NMR data of non-standard nuclei can correct or improve X-ray diffraction data. Our results indicate that, despite sizable quadrupolar interactions, (79/81)Br magnetic resonance spectroscopy is a powerful characterisation tool that allows for the differentiation between chemically similar bromine sites, as shown through the range in the characteristic NMR parameters. (35/37)Cl solid-state NMR data, obtained for an analogous phosphonium chloride sample, provide insight into the relationship between unit cell volume, nuclear quadrupolar coupling constants, and Sternheimer antishielding factors. The experimental findings are complemented by gauge-including projector-augmented wave (GIPAW) DFT calculations, which substantiate our experimentally determined strong dependence of the largest component of the bromine CS tensor, δ(11), on the shortest Br-P distance in the crystal structure, a finding that has possible application in the field of NMR crystallography. This trend is explained in terms of Ramsey's theory on paramagnetic shielding. Overall, this work demonstrates how careful NMR studies of underexploited exotic nuclides, such

Bromide supplementation exacerbated the renal dysfunction, injury and fibrosis in a mouse model of Alport syndrome.

PubMed

Yokota, Tsubasa; Omachi, Kohei; Suico, Mary Ann; Kojima, Haruka; Kamura, Misato; Teramoto, Keisuke; Kaseda, Shota; Kuwazuru, Jun; Shuto, Tsuyoshi; Kai, Hirofumi

2017-01-01

A seminal study recently demonstrated that bromide (Br-) has a critical function in the assembly of type IV collagen in basement membrane (BM), and suggested that Br- supplementation has therapeutic potential for BM diseases. Because salts of bromide (KBr and NaBr) have been used as antiepileptic drugs for several decades, repositioning of Br- for BM diseases is probable. However, the effects of Br- on glomerular basement membrane (GBM) disease such as Alport syndrome (AS) and its impact on the kidney are still unknown. In this study, we administered daily for 16 weeks 75 mg/kg or 250 mg/kg (within clinical dosage) NaBr or NaCl (control) via drinking water to 6-week-old AS mice (mouse model of X-linked AS). Treatment with 75 mg/kg NaBr had no effect on AS progression. Surprisingly, compared with 250 mg/kg NaCl, 250 mg/kg NaBr exacerbated the progressive proteinuria and increased the serum creatinine and blood urea nitrogen in AS mice. Histological analysis revealed that glomerular injury, renal inflammation and fibrosis were exacerbated in mice treated with 250 mg/kg NaBr compared with NaCl. The expressions of renal injury markers (Lcn2, Lysozyme), matrix metalloproteinase (Mmp-12), pro-inflammatory cytokines (Il-6, Il-8, Tnf-α, Il-1β) and pro-fibrotic genes (Tgf-β, Col1a1, α-Sma) were also exacerbated by 250 mg/kg NaBr treatment. Notably, the exacerbating effects of Br- were not observed in wild-type mice. These findings suggest that Br- supplementation needs to be carefully evaluated for real positive health benefits and for the absence of adverse side effects especially in GBM diseases such as AS.

RNA extraction from various recalcitrant plant tissues with a cethyltrimethylammonium bromide-containing buffer followed by an acid guanidium thiocyanate-phenol-chloroform treatment.

PubMed

Suzuki, Yuji; Mae, Tadahiko; Makino, Amane

2008-07-01

High-quality total RNA was extracted using a cethyltrimethylammonium bromide-containing buffer followed by an acid guanidium thiocyanate-phenol-chloroform treatment from recalcitrant plant tissues such as tree leaves (pine, Norway spruce, ginkgo, Japanese cedar, rose), flowers (rose, Lotus japonicus) and storage tissues (seeds of Lotus japonicus and rice, sweet potato tuber, banana fruit). This protocol greatly reduced the time required for RNA extraction.

The effects of cetyltrimethylammonium bromide surfactant on alumina modified zinc oxides

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gac, Wojciech, E-mail: wojciech.gac@umcs.lublin.pl; Zawadzki, Witold; Słowik, Grzegorz

Highlights: • Synthesis of novel ZnO−Al{sub 2}O{sub 3} oxides in the presence of CTAB surfactant. • Determination of the structural, surface and optical properties. • Nanocrystalline, high-surface area ZnO−Al{sub 2}O{sub 3} oxides. • ZnO-Al{sub 2}O{sub 3} materials of different gap energy. - Abstract: Novel alumina modified zinc oxide materials were prepared by co-precipitation method in the presence of different amounts of cetyltrimethylammonium bromide (CTAB) surfactant. X-ray diffraction, {sup 27}Al magic-angle spinning Nuclear Magnetic Resonance Spectroscopy, and transmission electron microscopy studies evidenced formation of 10–15 nm zinc oxide nanoparticles in the presence of the small amounts of surfactant. Amorphous alumina andmore » zinc aluminate phases of different coordination environment of Al sites were identified. An increase of surfactant concentration led to the elongation of nanoparticles and changes of the nature of hydroxyl groups. Precipitation in the high CTAB concentration conditions facilitated formation of mesoporous materials of high specific surface area. The materials were composed of very small (2–3 nm) zinc aluminate spinel nanoparticles. High concentration of CTAB induced widening of band gap energy.« less

Low-Dimensional Organic Tin Bromide Perovskites and Their Photoinduced Structural Transformation.

PubMed

Zhou, Chenkun; Tian, Yu; Wang, Mingchao; Rose, Alyssa; Besara, Tiglet; Doyle, Nicholas K; Yuan, Zhao; Wang, Jamie C; Clark, Ronald; Hu, Yanyan; Siegrist, Theo; Lin, Shangchao; Ma, Biwu

2017-07-24

Hybrid organic-inorganic metal halide perovskites possess exceptional structural tunability, with three- (3D), two- (2D), one- (1D), and zero-dimensional (0D) structures on the molecular level all possible. While remarkable progress has been realized in perovskite research in recent years, the focus has been mainly on 3D and 2D structures, with 1D and 0D structures significantly underexplored. The synthesis and characterization of a series of low-dimensional organic tin bromide perovskites with 1D and 0D structures is reported. Using the same organic and inorganic components, but at different ratios and reaction conditions, both 1D (C 4 N 2 H 14 )SnBr 4 and 0D (C 4 N 2 H 14 Br) 4 SnBr 6 can be prepared in high yields. Moreover, photoinduced structural transformation from 1D to 0D was investigated experimentally and theoretically in which photodissociation of 1D metal halide chains followed by structural reorganization leads to the formation of a more thermodynamically stable 0D structure. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Influence of pyridostigmine bromide on human thermoregulation during cold-water immersion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cadarette, B.S.; Prusaczyk, W.K.; Sawka, M.N.

1991-03-11

This study examined the effects of an oral 30 mg dose of pyridostigmine bromide (PYR) on thermoregulatory and physiological responses during cold stress. Six men were immersed in chilled stirred water for up to 180 minutes; once 2 hours following ingestion of PYR and once 2 hours following ingestion of a placebo (CON). With PYR, mean ({plus minus} SD) red blood cell cholinesterase inhibition was 33 ({plus minus}12)% at 110 minutes post-ingestion. Cholinesterase inhibition was negatively related to lean body mass. Abdominal discomfort caused termination in 3 of 6 PYR experiments ({bar X} immersion time = 117 min) but inmore » no CON experiments ({bar X} immersion time = 142 min, p > 0.05). During immersion, metabolic rate increased significantly over pre-immersion levels, and increased with duration of immersion, but did not differ between conditions. PYR had no significant effect on rectal temperature, mean body temperature, thermal sensation, heart rate, or plasma cortisol concentration. It was concluded that a 30 mg dose of PYR does not increase susceptibility to hypothermia in humans immersed in cold-water; however, in combination with cold-stress, PYR may result in marked abdominal cramping and limit cold tolerance.« less

Reversible air-induced optical and electrical modulation of methylammonium lead bromide (MAPbBr3) single crystals

NASA Astrophysics Data System (ADS)

Zhang, Huotian; Liu, Yiting; Lu, Haizhou; Deng, Wan; Yang, Kang; Deng, Zunyi; Zhang, Xingmin; Yuan, Sijian; Wang, Jiao; Niu, Jiaxin; Zhang, Xiaolei; Jin, Qingyuan; Feng, Hongjian; Zhan, Yiqiang; Zheng, Lirong

2017-09-01

The photoluminescence (PL) variations of organic-inorganic hybrid lead halide perovskites in different atmospheres are well documented, while the fundamental mechanism still lacks comprehensive understandings. This study reports the reversible optical and electrical properties of methylammonium lead bromide (MAPbBr3 or CH3NH3PbBr3) single crystals caused by air infiltration. With the change in the surrounding atmosphere from air to vacuum, the PL intensity of perovskite single crystals decreases, while the conductivity increases. By means of first-principles computational studies, the shallow trap states are considered as key elements in PL and conductivity changes. These results have important implications for the characterization and application of organic-inorganic hybrid lead halide perovskites in vacuum.

Morphological and functional manifestations of rat adrenal-cortex response to sodium bromide administration under hypodynamic stress

NASA Technical Reports Server (NTRS)

Kirichek, L. T.; Zholudeva, V. I.

1979-01-01

Functional and morphological manifestations of adrenal cortex response to hypodynamia (2-hr immobilization on an operating table) under the influence of bromine preparations were studied. The sodium bromide was administered intraperitoneally in 100, 250, and 500 mg/kg doses once and repeatedly during ten days. The adrenal gland was evaluated functionally by ascorbic acid and cholesterol content and morphologically by coloring it with hematoxylin-eosin and Sudans for lipid revealing at freezing. Results are displayed in two tables and microphotographs. They are summarized as follows: the bromine weakens the functional state of the adrenal cortex in intact rats, causing changes similar to those under stress. During immobilization combined with preliminary bromine administration, a less pronounced stress reaction is noticeable.

Methyl bromide determination in selected foods by headspace technique.

PubMed

Daft, J L

1993-01-01

A headspace method used earlier for determining methyl bromide (MB) in assorted nuts and peanut butters has been successfully applied to other foods that could potentially contain traces of this toxic fumigant. The foods tested include 63 off-the-shelf spices and seasonings, 83 table-ready items (grain-based, dried, or highly seasoned), 30 dried fruits and trail mixes, and 38 oil-based items (oil-seeds, cooking oils, or spicy oil-based dressings). Sample headspace gas is produced by blending < or = 50 g sample in 250 +/- 50 mL aqueous solution in a sealed 1000 mL blender cup. After equilibration at 25 degrees C, the headspace is sampled with a gas-tight syringe and injected into a dual column-dual detector gas chromatograph. One determination is made with a 20% OV-101 packed column and a 63Ni electron capture detector (ECD), the other with a GS-Q wide-bore capillary column and a Hall electrolytic conductivity detector (HECD). Of the approximately 200 samples tested, none contained detectable MB residue at a quantitation limit < 100 ng/g sample. All fortified samples yielded MB recovery. Samples were fortified at levels ranging from 78 to 3250 ng MB/g. Recoveries ranged from a mean high of 56% for spices and seasonings to a mean low of 30% for oil-based foods. The overall recovery and CV, including the results from assorted nuts and peanut butters, were 46 and 33%, respectively.

Benefits from sustained-release pyridostigmine bromide in myasthenia gravis: results of a prospective multicenter open-label trial.

PubMed

Sieb, Jörn Peter; Köhler, Wolfgang

2010-11-01

For more than 50 years the acetylcholinesterase inhibitor pyridostigmine bromide has been the drug of choice in the symptomatic therapy for myasthenia gravis. The sustained-release dosage form of pyridostigmine (SR-Pyr) is only available in a limited number of countries (e.g. in the United States and Germany). Astonishingly, the therapeutic usefulness of SR-Pyr has not yet been evaluated. In this non-interventional prospective open-label trial, 72 patients with stable myasthenia gravis were switched from instant-release dosage forms of pyridostigmine bromide to SR-Pyr. The results from the 37 patients younger than 60 years were separately analyzed. The initial daily dose of SR-Pyr was 288.1 ± 171.0mg. The drug switch was unproblematic in all patients. The number of daily doses was significantly reduced from 4.3 to 3.6 (p=0.011). The switch to SR-Pyr ameliorated the total quantified myasthenia gravis (QMG) score from 0.9 ± 0.5 to 0.6 ± 0.4 (p<0.001) in all patients and in the younger subgroup. This was accompanied by a significant improvement in the quality of life parameters. The health status valued by EuroQoL questionnaire improved from 0.626 ± 0.286 to 0.782 ± 0.186 (p<0.001). After switching to SR-Pyr, 28 adverse reactions disappeared and 24 adverse reactions occurred less frequent or weaker, however, 17 new adverse reactions were documented. Our results support the usefulness of SR-Pyr in an individualized therapeutic regimen to improve quality of life regardless of the patient's age in myasthenia gravis. Copyright © 2010 Elsevier B.V. All rights reserved.

Evaporation for Lithium Bromide Aqueous Solution in a Falling Film Heater under Reduced Pressures

NASA Astrophysics Data System (ADS)

Matsuda, Akira; Ide, Tetsuo; Yukino, Keiji

Experiments on evaporation for water and lithium bromide (LiBr) aqueous solution were made in a externally heated wetted-wall column under reduced pressures. For water, evaporation rate increased slightly as feed rate decreased. The heat transfer coefficients of falling film agreed with those for filmwise condensation. For LiBr solution, evaporation rate decreased and outlet temperature of LiBr solution increased as feed rate decreased. The equations of continuity, diffusion and energy which assume that only water moves to the surface and LiBr doesn't move through falling film of LiBr solution were solved numerically. Calculated values of evaporation rate and outlet temperature of solution agreed with experimental results. The results of this work were compared with pool boiling data reported previously, and it was shown that falling film heater is superior to pool boiling heater concerning heat transfer.

Mammography film processor replenishment rate: bromide level monitoring.

PubMed

Kimme-Smith, C; Wuelfing, P; Kitts, E L; Cagnon, C; Basic, M; Bassett, L

1997-03-01

The effects of the mammography film processing replenishment rate on contrast and speed are studied sensitometrically. Two experiments studied decreasing replenishment rates in the Kodak RP developer and quantified changes in the developer by measuring bromide ion concentrations. First, values of NaBr concentration from 1.7 to 8.4 g/L, achieved by reducing the replenishment rate, were tested with sensitometry strips. Second, the developer replenishment rate of a high volume dedicated mammography processor was reduced by one-third, to 20 cm3/1560 cm2, so that the NaBr concentration rose from 2.0 to 12.36. Sensitometric results for four film types and patient films were tested for changes from standard values as NaBr concentration was restored to 3.31 g/L. Fifty-five clinical images obtained at 7.3-9.3 NaBr g/L were compared to their matching previous films, with NaBr levels of 2-3 g/L, for contrast and visibility of the skin line. For the range of the NaBr ion from 1.7 to 7 g/L, no significant sensitometric differences were found. Above 7 g/L, different film types had different sensitometric results. From 7.3 to 9.3 NaBr g/L, 47.5% of the clinical films reviewed by four radiologists had less contrast compared to previous films. Dedicated mammography processors with high film volume (i.e., those that do not have excessive oxidation or foreign dye problems) can operate at lower replenishment rates than are currently employed. All common mammography film types are stable at these lower replenishment rates up to 7.0 NaBr g/L.

Membrane electrodes for the determination of pyridostigmine bromide.

PubMed

El-Kosasy, Amira M; Salem, Maissa Y; El-Bardicy, Mohamed G; Abd El-Rahman, Mohamed K

2009-01-01

Two pyridostigmine bromide (PB) selective electrodes were investigated with 2-nitrophenyl octyl ether as a plasticizer in a polymeric matrix of carboxylated polyvinyl chloride (PVC-COOH), based on the interaction between the drug solution and the dissociated COOH groups in the PVC-COOH. One of the sensors was fabricated by using PVC-COOH only as anionic site without incorporation of an ionophore (sensor 1). The second sensor was constructed by using 2-hydroxy propyl beta-cyclodextrin as an ionophore (sensor 2). Linear responses of PB within a concentration range of 10(-3)-10(-2) and 10(-5)-10(-2) M, with slopes of 51.9 +/- 0.31 and 56.7 +/- 0.40 mV/decade over pH range of 5-10 were obtained using sensors 2 and 1, respectively. The proposed method displayed useful analytical characteristics for determination of PB in tablets with average recoveries of 100.22 +/- 0.62, and 100.15 +/- 0.72, and in plasma with average recoveries of 99.14 +/- 1.19 and 99.79 +/- 0.72, for sensors 2 and 1, respectively. The utility of 2-hydroxy propyl beta-cyclodextrin as an ionophore has a significant influence on increasing both membrane sensitivity and selectivity of sensor 2 in comparison with sensor 1. The methods were also used to determine the intact drug in the presence of its degradate, and thus could be used as stability-indicating methods. The results obtained by the proposed procedures were statistically analyzed and compared with those obtained by the U.S. Pharmacopeia method. No significant difference for either accuracy or precision was observed.

Removal of bromide and bromate from drinking water using granular activated carbon.

PubMed

Zhang, Yong-Qing; Wu, Qing-Ping; Zhang, Ju-Mei; Yang, Xiu-Hua

2015-03-01

Granular activated carbon (GAC) was used to remove bromide (Br⁻) and bromate (BrO(3)(-)) from drinking water in both bench- and pilot-scale experiments. The present study aims to minimize BrO(3)(-) formation and eliminate BrO(3)(-) generated during the ozonation of drinking water, particularly in packaged drinking water. Results show that the Br⁻ and BrO(3)(-) levels in GAC-treated water decreased in both bench- and pilot-scale experiments. In the bench-scale experiments, when the empty bed contact time (EBCT) was 5 min, the highest reduction rates of Br(-) in the mineral and ultrapure water were found to be 74.9% and 91.2%, respectively, and those of BrO(3)(-) were 94.4% and 98.8%, respectively. The GAC capacity for Br⁻ and BrO(3)(-) removal increased with the increase in EBCT. Reduction efficiency was better in ultrapure water than in mineral water. In the pilot-scale experiments, the minimum reduction rates of Br⁻ and BrO(3)(-) were 38.5% and 73.2%, respectively.

Manganese-Doped One-Dimensional Organic Lead Bromide Perovskites with Bright White Emissions.

PubMed

Zhou, Chenkun; Tian, Yu; Khabou, Oussama; Worku, Michael; Zhou, Yan; Hurley, Joseph; Lin, Haoran; Ma, Biwu

2017-11-22

Single-component white-emitting phosphors are highly promising to simplify the fabrication of optically pumped white light-emitting diodes. To achieve white emission, precise control of the excited state dynamics is required for a single-component system to generate emissions with different energies in the steady state. Here, we report a new class of white phosphors based on manganese (Mn)-doped one-dimensional (1D) organic lead bromide perovskites. The bright white emission is the combination of broadband blue emission from the self-trapped excited states of the 1D perovskites and red emission from the doped Mn 2+ ions. Because of the indirect nature of the self-trapped excited states in 1D perovskites, there is no energy transfer from these states to the Mn 2+ ions, resulting in an efficient dual emission. As compared to the pristine 1D perovskites with bluish-white emission, these Mn-doped 1D perovskites exhibit much higher color rendering index of up to 87 and photoluminescence quantum efficiency of up to 28%.

Methyl chloride and methyl bromide emissions from baking: an unrecognized anthropogenic source.

PubMed

Thornton, Brett F; Horst, Axel; Carrizo, Daniel; Holmstrand, Henry

2016-05-01

Methyl chloride and methyl bromide (CH3Cl and CH3Br) are the largest natural sources of chlorine and bromine, respectively, to the stratosphere, where they contribute to ozone depletion. We report the anthropogenic production of CH3Cl and CH3Br during breadbaking, and suggest this production is an abiotic process involving the methyl ester functional groups in pectin and lignin structural polymers of plant cells. Wide variations in baking styles allow only rough estimates of this flux of methyl halides on a global basis. A simple model suggests that CH3Br emissions from breadbaking likely peaked circa 1990 at approximately 200tonnes per year (about 0.3% of industrial production), prior to restrictions on the dough conditioner potassium bromate. In contrast, CH3Cl emissions from breadbaking may be of similar magnitude as acknowledged present-day CH3Cl industrial emissions. Because the mechanisms involve functional groups and compounds widely found in plant materials, this type of methyl halide production may occur in other cooking techniques as well. Copyright © 2016 Elsevier B.V. All rights reserved.

Experimental studies of Debye-like process and structural relaxation in mixtures of 2-ethyl-1-hexanol and 2-ethyl-1-hexyl bromide

NASA Astrophysics Data System (ADS)

Preuß, M.; Gainaru, C.; Hecksher, T.; Bauer, S.; Dyre, J. C.; Richert, R.; Böhmer, R.

2012-10-01

Binary solutions of 2-ethyl-1-hexanol (2E1H) with 2-ethyl-1-hexyl bromide (2E1Br) are investigated by means of dielectric, shear mechanical, near-infrared, and solvation spectroscopy as well as dielectrically monitored physical aging. For moderately diluted 2E1H the slow Debye-like process, which dominates the dielectric spectra of the neat monohydroxy alcohol, separates significantly from the α-relaxation. For example, the separation in equimolar mixtures amounts to four decades in frequency. This situation of highly resolved processes allows one to demonstrate unambiguously that physical aging is governed by the α-process, but even under these ideal conditions the Debye process remains undetectable in shear mechanical experiments. Furthermore, the solvation experiments show that under constant charge conditions the microscopic polarization fluctuations take place on the time scale of the structural process. The hydrogen-bond populations monitored via near-infrared spectroscopy indicate the presence of a critical alcohol concentration, xc ≈ 0.5-0.6, thereby confirming the dielectric data. In the pure bromide a slow dielectric process of reduced intensity is present in addition to the main relaxation. This is taken as a sign of intermolecular cooperativity probably mediated via halogen bonds.

Molecular cloning of the plasma membrane H(+)-ATPase from Kluyveromyces lactis: a single nucleotide substitution in the gene confers ethidium bromide resistance and deficiency in K+ uptake.

PubMed Central

Miranda, M; Ramírez, J; Peña, A; Coria, R

1995-01-01

A Kluyveromyces lactis strain resistant to ethidium bromide and deficient in potassium uptake was isolated. Studies on the proton-pumping activity of the mutant strain showed that a decreased H(+)-ATPase specific activity was responsible for the observed phenotypes. The putative K. lactis PMA1 gene encoding the plasma membrane H(+)-ATPase was cloned by its ability to relieve the potassium transport defect of this mutant and by reversing its resistance to ethidium bromide. Its deduced amino acid sequence predicts a protein 899 residues long that is structurally colinear in its full length to H(+)-ATPases cloned from different yeasts, except for the presence of a variable N-terminal domain. By PCR-mediated amplification, we identified a transition from G to A that rendered the substitution of the fully conserved methionine at position 699 by isoleucine. We attribute to this amino acid change the low capacity of the mutant H(+)-ATPase to pump out protons. PMID:7730265

Behavioral, cellular and molecular maladaptations covary with exposure to pyridostigmine bromide in a rat model of gulf war illness pain.

PubMed

Cooper, B Y; Flunker, L D; Johnson, R D; Nutter, T J

2018-08-01

Many veterans of Operation Desert Storm (ODS) struggle with the chronic pain of Gulf War Illness (GWI). Exposure to insecticides and pyridostigmine bromide (PB) have been implicated in the etiology of this multisymptom disease. We examined the influence of 3 (DEET (N,N-diethyl-meta-toluamide), permethrin, chlorpyrifos) or 4 GW agents (DEET, permethrin, chlorpyrifos, pyridostigmine bromide (PB)) on the post-exposure ambulatory and resting behaviors of rats. In three independent studies, rats that were exposed to all 4 agents consistently developed both immediate and delayed ambulatory deficits that persisted at least 16 weeks after exposures had ceased. Rats exposed to a 3 agent protocol (PB excluded) did not develop any ambulatory deficits. Cellular and molecular studies on nociceptors harvested from 16WP (weeks post-exposure) rats indicated that vascular nociceptor Na v 1.9 mediated currents were chronically potentiated following the 4 agent protocol but not following the 3 agent protocol. Muscarinic linkages to muscle nociceptor TRPA1 were also potentiated in the 4 agent but not the 3 agent, PB excluded, protocol. Although K v 7 activity changes diverged from the behavioral data, a K v 7 opener, retigabine, transiently reversed ambulation deficits. We concluded that PB played a critical role in the development of pain-like signs in a GWI rat model and that shifts in Na v 1.9 and TRPA1 activity were critical to the expression of these pain behaviors. Copyright © 2018 Elsevier Inc. All rights reserved.

Molecular mechanism of NDMA formation from N,N-dimethylsulfamide during ozonation: quantum chemical insights into a bromide-catalyzed pathway.

PubMed

Trogolo, Daniela; Mishra, Brijesh Kumar; Heeb, Michèle B; von Gunten, Urs; Arey, J Samuel

2015-04-07

During ozonation of drinking water, the fungicide metabolite N,N-dimethylsulfamide (DMS) can be transformed into a highly toxic product, N-nitrosodimethylamine (NDMA). We used quantum chemical computations and stopped-flow experiments to evaluate a chemical mechanism proposed previously to describe this transformation. Stopped-flow experiments indicate a pK(a) = 10.4 for DMS. Experiments show that hypobromous acid (HOBr), generated by ozone oxidation of naturally occurring bromide, brominates the deprotonated DMS(-) anion with a near-diffusion controlled rate constant (7.1 ± 0.6 × 10(8) M(-1) s(-1)), forming Br-DMS(-) anion. According to quantum chemical calculations, Br-DMS has a pK(a) ∼ 9.0 and thus remains partially deprotonated at neutral pH. The anionic Br-DMS(-) bromamine can react with ozone with a high rate constant (10(5 ± 2.5) M(-1) s(-1)), forming the reaction intermediate (BrNO)(SO2)N(CH3)2(-). This intermediate resembles a loosely bound complex between an electrophilic nitrosyl bromide (BrNO) molecule and an electron-rich dimethylaminosulfinate ((SO2)N(CH3)2(-)) fragment, based on inspection of computed natural charges and geometric parameters. This fragile complex undergoes immediate (10(10 ± 2.5) s(-1)) reaction by two branches: an exothermic channel that produces NDMA, and an entropy-driven channel giving non-NDMA products. Computational results bring new insights into the electronic nature, chemical equilibria, and kinetics of the elementary reactions of this pathway, enabled by computed energies of structures that are not possible to access experimentally.

Bromination of aromatic compounds by residual bromide in sodium chloride matrix modifier salt during heated headspace GC/MS analysis.

PubMed

Fine, Dennis D; Ko, Saebom; Huling, Scott

2013-12-15

Analytical artifacts attributed to the bromination of toluene, xylenes, and trimethylbenzenes were found during the heated headspace gas chromatography/mass spectrometry (GC/MS) analysis of aqueous samples. The aqueous samples were produced from Fenton-like chemical oxidation reactions and contained aromatic compounds, hydrogen peroxide (H2O2), and ferric sulfate. Prior to GC/MS headspace analysis, the samples were acidified (pH<2), and sodium chloride was amended to the headspace vial as a matrix modifier. The brominated artifacts were generated during heated headspace analysis. Further, when samples were spiked with a mixture of volatile chlorinated and aromatic compounds (50 µg/L), poor spike recoveries of toluene and xylenes occurred, and in some cases complete loss of trimethylbenzenes and naphthalene resulted. Where poor recovery of aromatic spike compounds occurred, brominated aromatic compounds were found. The only significant source of bromine in the reaction scheme is the bromide typically present (<0.01% w/w) in the sodium chloride amended to the samples. Conversely, brominated artifacts were absent when a buffered salt mixture composed of sodium chloride and potassium phosphate dibasic/monobasic was used as a matrix modifier and raised the sample pH (pH~6). This indicated that the brominated artifacts resulted from the reaction of the aromatic compounds with BrCl, which was formed by the reaction of H2O2, chloride, and bromide under acidic conditions. An alternative matrix modifier salt is recommended that prevents the bromination reaction and avoids these deleterious effects on sample integrity during headspace analysis. Published by Elsevier B.V.

Room temperature X- and gamma-ray detectors using thallium bromide crystals

NASA Astrophysics Data System (ADS)

Hitomi, K.; Muroi, O.; Shoji, T.; Suehiro, T.; Hiratate, Y.

1999-10-01

Thallium bromide (TlBr) is a compound semiconductor with wide band gap (2.68eV) and high X- and γ-ray stopping power. The TlBr crystals were grown by the horizontal travelling molten zone (TMZ) method using purified material. Two types of room temperature X- and γ-ray detectors were fabricated from the TlBr crystals: TlBr detectors with high detection efficiency for positron annihilation γ-ray (511keV) detection and TlBr detectors with high-energy resolution for low-energy X-ray detection. The detector of the former type demonstrated energy resolution of 56keV FWHM (11%) for 511keV γ-rays. Energy resolution of 1.81keV FWHM for 5.9keV was obtained from the detector of the latter type. In order to analyze noise characteristics of the detector-preamplifier assembly, the equivalent noise charge (ENC) was measured as a function of the amplifier shaping time for the high-resolution detector. This analysis shows that parallel white noise and /1/f noise were dominant noise sources in the detector system. Current-voltage characteristics of the TlBr detector with a small Peltier cooler were also measured. Significant reduction of the detector leakage current was observed for the cooled detectors.

Single nucleotide polymorphism discrimination with and without an ethidium bromide intercalator.

PubMed

Fenati, Renzo A; Connolly, Ashley R; Ellis, Amanda V

2017-02-15

Single nucleotide polymorphism (SNP) genotyping is an important aspect in understanding genetic variations. Here, we discriminate SNPs using toe-hold mediated displacement reactions. The biological target is an 80 nucleotide long double-stranded-DNA from the mtDNA HV1 region, associated with maternal ancestry. This target has been specially designed with a pendant toehold and a cationic fluorophore, ATTO 647N, as a reporter, produced in a polymerase chain reaction. Rates of reaction for the toehold-polymerase chain reaction products (TPPs) with their corresponding complementary displacing sequences, labelled with a Black Hole Quencher 1, followed the order TPP-Cytosine > TPP-Thymine > TPP-Adenine ≥ TPP-Guanine. Non-complementary rates were the slowest with mismatches involving cytosine. These reactions, operating in a static/or contact mode, gave averaged readouts between SNPs within 15 min (with 80-90% quenching), compared to 25-30 min in previous studies involving fluorescence resonance energy transfer. Addition of an intercalating agent, ethidium bromide, retarded the rate of reaction in which cytosine was involved, presumably through stabilization of the base pairing, which resulted in markedly improved discrimination of cytosine containing SNPs. Copyright © 2016 Elsevier B.V. All rights reserved.

Description of toluene inhibition of methyl bromide biodegradation in seawater and isolation of a marine toluene oxidizer that degrades methyl bromide.

PubMed

Goodwin, Kelly D; Tokarczyk, Ryszard; Stephens, F Carol; Saltzman, Eric S

2005-07-01

Methyl bromide (CH3Br) and methyl chloride (CH3Cl) are important precursors for destruction of stratospheric ozone, and oceanic uptake is an important component of the biogeochemical cycle of these methyl halides. In an effort to identify and characterize the organisms mediating halocarbon biodegradation, we surveyed the effect of potential cometabolic substrates on CH3Br biodegradation using a 13CH3Br incubation technique. Toluene (160 to 200 nM) clearly inhibited CH3Br and CH3Cl degradation in seawater samples from the North Atlantic, North Pacific, and Southern Oceans. Furthermore, a marine bacterium able to co-oxidize CH3Br while growing on toluene was isolated from subtropical Western Atlantic seawater. The bacterium, Oxy6, was also able to oxidize o-xylene and the xylene monooxygenase (XMO) pathway intermediate 3-methylcatechol. Patterns of substrate oxidation, lack of acetylene inhibition, and the inability of the toluene 4-monooxygenase (T4MO)-containing bacterium Pseudomonas mendocina KR1 to degrade CH3Br ruled out participation of the T4MO pathway in Oxy6. Oxy6 also oxidized a variety of toluene (TOL) pathway intermediates such as benzyl alcohol, benzylaldehyde, benzoate, and catechol, but the inability of Pseudomonas putida mt-2 to degrade CH3Br suggested that the TOL pathway might not be responsible for CH3Br biodegradation. Molecular phylogenetic analysis identified Oxy6 to be a member of the family Sphingomonadaceae related to species within the Porphyrobacter genus. Although some Sphingomonadaceae can degrade a variety of xenobiotic compounds, this appears to be the first report of CH3Br degradation for this class of organism. The widespread inhibitory effect of toluene on natural seawater samples and the metabolic capabilities of Oxy6 indicate a possible link between aromatic hydrocarbon utilization and the biogeochemical cycle of methyl halides.

Characterization of Jamaican agro-industrial wastes. Part II, fatty acid profiling using HPLC: precolumn derivatization with phenacyl bromide.

PubMed

Bailey-Shaw, Y A; Golden, K D; Pearson, A G M; Porter, R B R

2012-09-01

This paper describes the determination of fatty acid composition of coffee, citrus and rum distillery wastes using reversed-phase high-performance liquid chromatography (RP-HPLC). Lipid extracts of the waste samples are derivatized with phenacyl bromide and their phenacyl esters are separated on a C8 reversed-phase column by using continuous gradient elution with water and acetonitrile. The presence of saturated and unsaturated fatty acids in quantifiable amounts in the examined wastes, as well as the high percentage recoveries, are clear indications that these wastes have potential value as inexpensive sources of lipids. The HPLC procedures described here could be adopted for further analysis of materials of this nature.

Effects of choline 2:6-xylyl ether bromide upon the suprarenal medulla of the rat

PubMed Central

Coupland, R. E.; Exley, K. A.

1957-01-01

The administration of choline 2:6-xylyl ether bromide (TM 10) daily to rats for two weeks depletes the suprarenals of about one-half their normal content of adrenaline and noradrenaline. This depletion has been demonstrated histologically and by colorimetric and biological estimation of the amines present in extracts of the glands. Treatment with TM 10 causes similar histological signs of depletion in autografts of adrenal chromaffin tissue in the rat iris. Restoration of catechol amines in rat suprarenals, previously depleted by TM 10, occurs slowly and appears to be complete 14 days after withdrawing the drug. These results, considered in conjunction with the estimated rate of turnover of catechol amines in the rat suprarenal, lend support to the view that TM 10 may interfere with the biosynthesis of these amines. ImagesFIG. 1FIG. 2FIG. 3FIG. 4 PMID:13460235

(Carbonato-κO,O')bis-(di-2-pyridyl-amine-κN,N')cobalt(III) bromide.

PubMed

Czapik, Agnieszka; Papadopoulos, Christos; Lalia-Kantouri, Maria; Gdaniec, Maria

2011-04-01

In the title compound, [Co(CO(3))(C(10)H(9)N(3))(2)]Br, a distorted octa-hedral coordination of the Co(III) atom is completed by four N atoms of the two chelating di-2-pyridyl-amine ligands and two O atoms of the chelating carbonate anion. The di-2-pyridyl-amine ligands are nonplanar and the dihedral angles between the 2-pyridyl groups are 29.11 (9) and 37.15 (12)°. The coordination cation, which has approximate C(2) symmetry, is connected to the bromide ion via an N-H⋯Br(-) hydrogen bond. The ionic pair thus formed is further assembled into a dimer via N-H⋯O inter-actions about an inversion centre. A set of weaker C-H⋯O and C-H⋯Br(-) inter-actions connect the dimers into a three-dimensional network.

Removal of hexavalent chromium by using red mud activated with cetyltrimethylammonium bromide.

PubMed

Li, Deliang; Ding, Ying; Li, Lingling; Chang, Zhixian; Rao, Zhengyong; Lu, Ling

2015-01-01

The removal of hexavalent chromium [Cr(VI)] from aqueous solution by using red mud activated with cetyltrimethylammonium bromide (CTAB) was studied. The optimum operation parameters, such as CTAB concentration, pH values, contact time, and initial Cr(VI) concentration, were investigated. The best concentration of CTAB for modifying red mud was found to be 0.50% (mCTAB/VHCl,0.6 mol/L). The lower pH (<2) was found to be much more favourable for the removal of Cr(VI). Red mud activated with CTAB can greatly improve the removal ratio of Cr(VI) as high as four times than that of original red mud. Adsorption equilibrium was reached within 30 min under the initial Cr(VI) concentration of 100 mg L(-1). The isotherm data were analysed using Langmuir and Freundlich models. The adsorption of Cr(VI) on activated red mud fitted well to the Langmuir isotherm model, and the maximum adsorption capacity was estimated as 22.20 mg g(-1) (Cr/red mud). The adsorption process could be well described using the pseudo-second-order model. The result shows that activated red mud is a promising agent for low-cost water treatment.

Prediction of strontium bromide laser efficiency using cluster and decision tree analysis

NASA Astrophysics Data System (ADS)

Iliev, Iliycho; Gocheva-Ilieva, Snezhana; Kulin, Chavdar

2018-01-01

Subject of investigation is a new high-powered strontium bromide (SrBr2) vapor laser emitting in multiline region of wavelengths. The laser is an alternative to the atom strontium lasers and electron free lasers, especially at the line 6.45 μm which line is used in surgery for medical processing of biological tissues and bones with minimal damage. In this paper the experimental data from measurements of operational and output characteristics of the laser are statistically processed by means of cluster analysis and tree-based regression techniques. The aim is to extract the more important relationships and dependences from the available data which influence the increase of the overall laser efficiency. There are constructed and analyzed a set of cluster models. It is shown by using different cluster methods that the seven investigated operational characteristics (laser tube diameter, length, supplied electrical power, and others) and laser efficiency are combined in 2 clusters. By the built regression tree models using Classification and Regression Trees (CART) technique there are obtained dependences to predict the values of efficiency, and especially the maximum efficiency with over 95% accuracy.

Mitochondrial nucleoid clusters protect newly synthesized mtDNA during Doxorubicin- and Ethidium Bromide-induced mitochondrial stress

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alán, Lukáš, E-mail: lukas.alan@fgu.cas.cz; Špaček

Mitochondrial DNA (mtDNA) is compacted in ribonucleoprotein complexes called nucleoids, which can divide or move within the mitochondrial network. Mitochondrial nucleoids are able to aggregate into clusters upon reaction with intercalators such as the mtDNA depletion agent Ethidium Bromide (EB) or anticancer drug Doxorobicin (DXR). However, the exact mechanism of nucleoid clusters formation remains unknown. Resolving these processes may help to elucidate the mechanisms of DXR-induced cardiotoxicity. Therefore, we addressed the role of two key nucleoid proteins; mitochondrial transcription factor A (TFAM) and mitochondrial single-stranded binding protein (mtSSB); in the formation of mitochondrial nucleoid clusters during the action of intercalators.more » We found that both intercalators cause numerous aberrations due to perturbing their native status. By blocking mtDNA replication, both agents also prevented mtDNA association with TFAM, consequently causing nucleoid aggregation into large nucleoid clusters enriched with TFAM, co-existing with the normal nucleoid population. In the later stages of intercalation (> 48 h), TFAM levels were reduced to 25%. In contrast, mtSSB was released from mtDNA and freely distributed within the mitochondrial network. Nucleoid clusters mostly contained nucleoids with newly replicated mtDNA, however the nucleoid population which was not in replication mode remained outside the clusters. Moreover, the nucleoid clusters were enriched with p53, an anti-oncogenic gatekeeper. We suggest that mitochondrial nucleoid clustering is a mechanism for protecting nucleoids with newly replicated DNA against intercalators mediating genotoxic stress. These results provide new insight into the common mitochondrial response to mtDNA stress and can be implied also on DXR-induced mitochondrial cytotoxicity. - Highlights: • The mechanism for mitochondrial nucleoid clustering is proposed. • DNA intercalators (Doxorubicin or Ethidium Bromide) prevent

Improved delivery of fenoterol plus ipratropium bromide using Respimat compared with a conventional metered dose inhaler.

PubMed

Goldberg, J; Freund, E; Beckers, B; Hinzmann, R

2001-02-01

Asthma can be effectively treated by the use of bronchodilator therapies administered by inhalation. The objective of this study was to describe the dose-response relationship of combined doses of fenoterol hydrobromide (F) and ipratropium bromide (I) (F/I) delivered via Respimat, a soft mist inhaler, and to establish the Respimat dose which is as efficacious and as safe as the standard marketed dose of F/I (100/40 microg) which is delivered via a conventional metered dose inhaler (MDI). In a double-blind (within device) cross-over study with a balanced incomplete block design, 62 patients with stable bronchial asthma (mean forced expiratory volume in one second (FEV1) 63% predicted) were randomized at five study centres to receive five out of eight possible treatments: placebo, F/I 12.5/5, 25/10, 50/20, 100/40 or 200/80 microg delivered via Respimat; F/I 50/20 or 100/40 microg delivered via MDI. Pulmonary function results were based on the per-protocol dataset, comprising 47 patients. All F/I doses produced greater increases in FEV1 than placebo. A log-linear dose-response was obtained for the average increase in FEV1 up to 6 h (AUC0-6 h) and peak FEV1 across the dose range administered by Respimat. Statistically, therapeutic equivalence was not demonstrated between any F/I dose administered by Respimat compared with the MDI. However 12.5/5 and 25/10 microg F/I administered via Respimat were closest (slightly superior) to the F/I dose of 100/40 microg delivered via MDI. Pharmacokinetic data from 34 patients indicated a two-fold greater systemic availability of both drugs following inhalation by Respimat compared to MDI. In general, the active treatments were well tolerated and safe with regard to vital signs, electrocardiography, laboratory parameters and adverse events. In conclusion, combined administration of fenoterol hydrobromide and ipratropium bromide via Respimat, is as effective and as safe as higher doses given via a metered dose inhaler.

Phosphorescent quantum dots/ethidium bromide nanohybrids based on photoinduced electron transfer for DNA detection.

PubMed

Bi, Lin; Yu, Yuan-Hua

2015-04-05

Mercaptopropionic acid-capped Mn-doped ZnS quantum dots/ethidium bromide (EB) nanohybrids were constructed for photoinduced electron transfer (PIET) and then used as a room-temperature phosphorescence (RTP) probe for DNA detection. EB could quench the RTP of Mn-doped ZnS QDs by PIET, thereby forming Mn-doped ZnS QDs/EB nanohybrids and storing RTP. Meanwhile, EB could be inserted into DNA and EB could be competitively desorbed from the surface of Mn-doped ZnS QDs by DNA, thereby releasing the RTP of Mn-doped ZnS QDs. Based on this mechanism, a RTP sensor for DNA detection was developed. Under optimal conditions, the detection limit for DNA was 0.045 mg L(-1), the relative standard deviation was 1.7%, and the method linear ranged from 0.2 to 20 mg L(-1). The proposed method was applied to biological fluids, in which satisfactory results were obtained. Copyright © 2015 Elsevier B.V. All rights reserved.

Reduction of bromate to bromide coupled to acetate oxidation by anaerobic mixed microbial cultures.

PubMed

van Ginkel, C G; van Haperen, A M; van der Togt, B

2005-01-01

Bromate, a weakly mutagenic oxidizing agent, exists in surface waters. The biodegradation of bromate was investigated by assessing the ability of mixed cultures of micro-organisms for utilization of bromate as electron acceptor and acetate as electron donor. Reduction of bromate was only observed at relatively low concentrations (<3.0 mM) in the absence of molecular oxygen. Under these conditions bromate was reduced stoichiometrically to bromide. Unadapted sludge from an activated sludge treatment plant and a digester reduced bromate without lag period at a constant rate. Using an enrichment culture adapted to bromate, it was demonstrated that bromate was a terminal electron acceptor for anaerobic growth. Approximately 50% of the acetate was utilized for growth with bromate by the enrichment culture. A doubling of 20 h was estimated from a logarithmic growth curve. Other electron acceptors, like perchlorate, chlorate and nitrate, were not reduced or at negligible rates by bromate-utilizing microorganisms.

The behavior of gain and saturation characteristics versus temperature in a copper bromide laser

NASA Astrophysics Data System (ADS)

Mohammadpour Lima, S.; Behrouzinia, S.; Salem, M. K.; Elahei, M.; Khorasani, K.; Dorranian, D.

2017-05-01

A pair of copper bromide lasers in an oscillator-amplifier configuration was used to investigate the temperature dependence of the small-signal gain, saturation intensity, and output power of the laser. The observations were explained in terms of the electron temperature and energy levels of transition. An optimum electrical input power of 1.6 kW and a corresponding operational temperature of 510 °C were determined for the maximum values of these parameters. The balance between the microscopic parameters, such as stimulated emission cross-section, laser upper-level lifetime, and population inversion, which determine the behavior of the amplifying parameters and laser output power with respect to the operational temperature, has been investigated. We used the steady-state rate equation from the Hargrove model to determine the amplifying parameters, instead of the Frantz-Nodvik formula. The power extracted from the amplifier exceeds that achieved with the same device as the oscillator by more than 60%.

1-Pentamethylbenzyl-3-(n)buthylbenzimidazolesilver(I)bromide complex: synthesis, characterization and DFT calculations.

PubMed

Kunduracıoğlu, Ahmet; Tamer, Ömer; Avcı, Davut; Kani, Ibrahim; Atalay, Yusuf; Cetinkaya, Bekir

2014-01-01

A novel NHC complex of silver(I) ion, 1-pentamethylbenzyl-3-(n)buthylbenzimidazolesilver(I)bromide, was prepared and fully characterized by single crystal X-ray structure determination. FT-IR, NMR and UV-vis spectroscopies were employed to investigate the electronic transition behaviors of the complex. Additionally, the molecular geometry, vibrational frequencies, gauge including atomic orbital (GIAO) (1)H and (13)C chemical shift and electronic transition values of silver(I) complex were calculated by using density functional theory levels (B3LYP and PBE1PBE) with LANL2DZ basis set. Also, the vibrational frequencies were supported on the basis of the potential energy distribution (PED) analysis calculated for PBE1PBE level. We were also investigated total static dipole moment (μ), the mean polarizability (〈α〉), the anisotropy of the polarizability (Δα), the mean first-order hyperpolarizability (〈β〉) of the title complex. Natural bond orbital (NBO) analysis was performed to determine the presence of hyperconjugative interactions, and charge distributions. Copyright © 2013 Elsevier B.V. All rights reserved.

Highly stereoselective three-component reactions of phenylselenomagnesium bromide, acetylenic sulfones, and saturated aldehydes/ketones or alpha,beta-unsaturated enals or enones.

PubMed

Huang, Xian; Xie, Meihua

2002-12-13

beta-Phenylseleno-alpha-tolylsulfonyl-substituted alkenes were synthesized via the three-component conjugate-nucleophilic addition of acetylenic sulfones, phenylselenomagnesium bromide, and carbonyl compounds, such as aldehydes, aliphatic ketones, or alpha,beta-unsaturated enals or enones. The reaction is highly regio- and stereoselective with moderate to good yields. Functionalized allylic alcohols were obtained in the case of aldehydes and aliphatic ketones. In the case of alpha,beta-unsaturated enones, functionalized allylic alcohols or functionalized gamma,delta-unsaturated ketones were obtained, depending on the structures of the ketones.

Eudragit RS PO nanoparticles for sustained release of pyridostigmine bromide

NASA Astrophysics Data System (ADS)

Hoobakht, Fatemeh; Ganji, Fariba; Vasheghani-Farahani, Ebrahim; Mousavi, Seyyed Mohammad

2013-09-01

Pyridostigmine bromide (PB) is an inhibitor of cholinesterase, which is used in the treatment of myasthenia gravis and administered for protection against exposure to toxic nerve agents. Tests were done to investigate prolonging the half-life of PB and improving its release behavior. PB was loaded in nanoparticles (NPs) of Eudragit RS PO (Eu-RS) prepared using the technique of quasi emulsion solvent diffusion. Variables of output power of the sonicator, bath temperature and mixing time, were chosen as the optimization factors to obtain the minimum sized NPs. In addition, emulsions were tested at different ratios of drug-to-polymer by dynamic light scattering to determine size and zeta potential of NPs. UV-spectroscopy was used to determine PB content of the NPs. Drug-loaded NPs were characterized by scanning electron microscopy, X-ray diffraction, and Fourier transform infrared spectra. Results determined that mixing time had a significant impact on the size of Eu-RS NPs, but power output of sonicator and bath temperature had no significant effect. The particle size obtained at the optimum condition (power output of 70 W, bath temperature of 33 °C, and mixing time of 7 min) was less than 200 nm (optimum sizes were 138.9 and 179.5 nm for Eu-RS and PB-loaded Eu-RS NPs, respectively). The optimum PB-loaded Eu-RS NPs at the PB to Eu-RS weight ratio of 1-4 and 20 % of loaded PB released from the nanocarriers within 100 h.

Effect of hexadecyltrimethylammonium bromide-based microemulsions on the rate of decomposition of the beta-lactam antibiotic cephaclor.

PubMed

De Oliveira, A G; Scarpa, M V; Chaimovich, H

1997-05-01

Microemulsions of hexadecyltrimethylammonium bromide (HTAB)/n-butanol/hexadecane/water catalyze the intramolecular degradation of cephaclor. The rate increase is a sensitive function of the microemulsion volume fraction and salt concentration. The effects of microemulsions, analyzed quantitatively using a pseudophase ion-exchange model, assumed that the extent of ion dissociation from the microemulsions varies with volume fraction. Comparison of micellar and microemulsion effects on the same reaction shows that microemulsions are less effective catalysts. Acceleration decreased significantly by increasing the relative proportion of n-butanol ratio in microemulsions and by addition of n-butanol in HTAB micelles. Comparison of the activation parameters of the reaction in aqueous solution, microemulsions, and micelles suggests that catalysis by both aggregates is driven mainly by entropic contributions.

Microextraction in a tetrabutylammonium bromide/ammonium sulfate aqueous two-phase system and electrohydrodynamic generation of a micro-droplet.

PubMed

Song, Young Soo; Choi, Young Hoon; Kim, Do Hyun

2007-08-31

Microextraction of methyl orange in the aqueous two-phase system (ATPS) formed by dissolving tetrabutylammonium bromide (TBAB) and ammonium sulfate (AS) is reported. Methyl orange was transported from the AS-rich phase to TBAB-rich phase across the interface of the two immiscible phases. The electrohydrodynamic effect on the shape of the interface of two immiscible flows was also observed by applying dc voltage at the T-junction of the microchannel and the generation of a droplet of AS-rich phase was observed when the potential difference between positive and negative electrodes exceeds a threshold voltage. The minimum voltage necessary for the droplet generation depends on pH due to the degree of dissociation and charge accumulation.

Bromidotetra­kis­(1H-2-ethyl-5-methyl­imidazole-κN 3)copper(II) bromide

PubMed Central

Godlewska, Sylwia; Baranowska, Katarzyna; Socha, Joanna; Dołęga, Anna

2011-01-01

The CuII ion in the title compound, [CuBr(C6H10N2)4]Br, is coordinated in a square-based-pyramidal geometry by the N atoms of four imidazole ligands and a bromide anion in the apical site. Both the CuII and Br− atoms lie on a crystallographic fourfold axis. In the crystal, the [CuBr(C6H10N2)4]+ complex cations are linked to the uncoordinated Br− anions (site symmetry ) by N—H⋯Br hydrogen bonds, generating a three-dimensional network. The ethyl group of the imidazole ligand was modelled as disordered over two orientations with occupancies of 0.620 (8) and 0.380 (8). PMID:22199662

Pyridostigmine bromide does not alter thermoregulation during exercise in cold air

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roberts, D.E.; Sawka, M.N.; Young, A.J.

1994-12-31

This study examined the effects of acute and chronic pyridostigmine bromide (PB) administration on thermoregulatory and metabolic responses to exercise in cold air (5 C). Seven healthy men completed two 7-day trials in a double-blind, crossover experimental design: during one trial they received PB (30 mg three times daily) and during the other trial they received placebo. For each trial, subjects attempted four (3 h) exercise tests: low-intensity exercise (25% Vo2max) and moderate- intensity exercise (-50% Vo2max), on days 2 and 3 and again on days 6 and 7. Metabolic rate, body temperatures, and venous blood samples were obtained beforemore » and during exercise. Red blood cell acerylcholinesterase inhibition induced by PB increased (p < 0.05) from 34% on day I to 43% on days 3-7 Metabolic rate, body temperatures, and regional heat conductance responses were not different between trials. Plasma glucose, glycerol, free fatty acid, lactate, sodium, and potassium concentrations were not different between trials. In addition. differences were not found between acute and chronic experiments for any thermoregulatory or metabolic responses. These findings demonstrate that the PB dosage used by military personnel, as a pharmacological defense against nerve-agent poisoning. should not cause any adverse thermoregulatory or metabolic effects during moderate activity in cold climates.« less

A General, Efficient and Functional-Group-Tolerant Catalyst System for the Palladium-Catalyzed Thioetherification of Aryl Bromides and Iodides

PubMed Central

Fernández-Rodríguez, Manuel A.; Hartwig, John F.

2010-01-01

The cross-coupling reaction of aryl bromides and iodides with aliphatic and aromatic thiols catalyzed by palladium complexes of the bisphosphine ligand CyPF-tBu (1) is reported. Reactions occur in excellent yields, broad scope, high tolerance of functional groups and with turnover numbers that exceed those of previous catalysts by two or three orders of magnitude. These couplings of bromo- and iodoarenes are more efficient than the corresponding reactions of chloroarenes and could be conducted with less catalyst loading and/or milder reaction conditions. Consequently, limitations regarding scope and functional group tolerance previously reported in the coupling of aryl chlorides are now overcome. PMID:19154131

Syntheses and crystal structures of the rare-earth metal(III) bromide ortho-oxidotungstates(VI) with the formula REBr[WO4] (RE = Y, Gd-Yb)

NASA Astrophysics Data System (ADS)

Schustereit, Tanja; Schleid, Thomas; Hartenbach, Ingo

2015-10-01

The rare-earth metal(III) bromide ortho-oxidotungstates(VI) with the formula REBr[WO4] crystallize triclinically in space group P 1 bar (a = 689-693, b = 715-728, c = 1074-1107 pm, α = 103-106, β ≈ 108 and γ = 93-95°, Z = 4) for RE = Y, Gd-Yb. Their crystal structure is isotypic with the most examples of the formally analogous lanthanoid(III) bromide oxidomolybdates(VI) REBr[MoO4] with RE = Y, Pr, Nd, Sm, Gd-Lu. It contains two crystallographically different rare-earth metal(III) cations with coordination numbers of seven plus one for (RE1)3+ and seven for (RE2)3+. The (RE1)3+ cations are surrounded by three Br- and four plus one O2- anions forming distorted trigonal dodecahedra, while the (RE2)3+ cations exhibit a coordination environment of one Br- and six O2- anions in the shape of a monocapped trigonal prism. Furthermore, the structure contains two crystallographically independent, isolated tetrahedral [WO4]2- units. All these polyhedra are fused together to form 1 ∞ {REBr[WO4]} chains running along [012]. Since the title compounds, synthesized by solid-state reactions from the underlying binaries, emerge as pure phases according to X-ray powder diffractometry, spectroscopic and magnetic measurements were performed.

Systematization of actinides using cluster analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kopyrin, A.A.; Terent`eva, T.N.; Khramov, N.N.

1994-11-01

A representation of the actinides in multidimensional property space is proposed for systematization of these elements using cluster analysis. Literature data for their atomic properties are used. Owing to the wide variation of published ionization potentials, medians are used to estimate them. Vertical dendograms are used for classification on the basis of distances between the actinides in atomic-property space. The properties of actinium and lawrencium are furthest removed from the main group. Thorium and mendelevium exhibit individualized properties. A cluster based on the einsteinium-fermium pair is joined by californium.

Reactions of guanine with methyl chloride and methyl bromide: O6-methylation versus charge transfer complex formation

NASA Astrophysics Data System (ADS)

Shukla, P. K.; Mishra, P. C.; Suhai, S.

Density functional theory (DFT) at the B3LYP/6-31+G* and B3LYP/AUG-cc-pVDZ levels was employed to study O6-methylation of guanine due to its reactions with methyl chloride and methyl bromide and to obtain explanation as to why the methyl halides cause genotoxicity and possess mutagenic and carcinogenic properties. Geometries of the various isolated species involved in the reactions, reactant complexes (RCs), and product complexes (PCs) were optimized in gas phase. Transition states connecting the reactant complexes with the product complexes were also optimized in gas phase at the same levels of theory. The reactant complexes, product complexes, and transition states were solvated in aqueous media using the polarizable continuum model (PCM) of the self-consistent reaction field theory. Zero-point energy (ZPE) correction to total energy and the corresponding thermal energy correction to enthalpy were made in each case. The reactant complexes of the keto form of guanine with methyl chloride and methyl bromide in water are appreciably more stable than the corresponding complexes involving the enol form of guanine. The nature of binding in the product complexes was found to be of the charge transfer type (O6mG+ · X-, X dbond Cl, Br). Binding of HCl, HBr, and H2O molecules to the PCs obtained with the keto form of guanine did not alter the positions of the halide anions in the PCs, and the charge transfer character of the PCs was also not modified due to this binding. Further, the complexes obtained due to the binding of HCl, HBr, and H2O molecules to the PCs had greater stability than the isolated PCs. The reaction barriers involved in the formation of PCs were found to be quite high (?50 kcal/mol). Mechanisms of genotoxicity, mutagenesis and carcinogenesis caused by the methyl halides appear to involve charge transfer-type complex formation. Thus the mechanisms of these processes involving the methyl halides appear to be quite different from those that involve the

Effects of Cholinergic Stimulation with Pyridostigmine Bromide on Chronic Chagasic Cardiomyopathic Mice

PubMed Central

de Cuba, Marília Beatriz; Ribeiro Machado, Marcus Paulo; Farnesi, Thais Soares; Alves, Angelica Cristina; Martins, Livia Alves; de Oliveira, Lucas Felipe; Capitelli, Caroline Santos; Leite, Camila Ferreira; Vinícius Silva, Marcos; Machado, Juliana Reis; Kappel, Henrique Borges; Sales de Campos, Helioswilton; Paiva, Luciano; da Silva Gomes, Natália Lins; Guimarães Faleiros, Ana Carolina; Britto, Constança Felicia de Paoli de Carvalho; Savino, Wilson; Moreira, Otacílio Cruz; Rodrigues Jr., Virmondes; Montano, Nicola; Lages-Silva, Eliane; Ramirez, Luis Eduardo; Dias da Silva, Valdo Jose

2014-01-01

The aim of the present study was to assess the effects of an anticholinesterase agent, pyridostigmine bromide (Pyrido), on experimental chronic Chagas heart disease in mice. To this end, male C57BL/6J mice noninfected (control:Con) or chronically infected (5 months) with Trypanosoma cruzi (chagasic:Chg) were treated or not (NT) with Pyrido for one month. At the end of this period, electrocardiogram (ECG); cardiac autonomic function; heart histopathology; serum cytokines; and the presence of blood and tissue parasites by means of immunohistochemistry and PCR were assessed. In NT-Chg mice, significant changes in the electrocardiographic, autonomic, and cardiac histopathological profiles were observed confirming a chronic inflammatory response. Treatment with Pyrido in Chagasic mice caused a significant reduction of myocardial inflammatory infiltration, fibrosis, and hypertrophy, which was accompanied by a decrease in serum levels of IFNγ with no change in IL-10 levels, suggesting a shift of immune response toward an anti-inflammatory profile. Lower nondifferent numbers of parasite DNA copies were observed in both treated and nontreated chagasic mice. In conclusion, our findings confirm the marked neuroimmunomodulatory role played by the parasympathetic autonomic nervous system in the evolution of the inflammatory-immune response to T. cruzi during experimental chronic Chagas heart disease in mice. PMID:25221388

Effects of cholinergic stimulation with pyridostigmine bromide on chronic chagasic cardiomyopathic mice.

PubMed

de Cuba, Marília Beatriz; Machado, Marcus Paulo Ribeiro; Farnesi, Thais Soares; Alves, Angelica Cristina; Martins, Livia Alves; de Oliveira, Lucas Felipe; Capitelli, Caroline Santos; Leite, Camila Ferreira; Silva, Marcos Vinícius; Machado, Juliana Reis; Kappel, Henrique Borges; de Campos, Helioswilton Sales; Paiva, Luciano; Gomes, Natália Lins da Silva; Faleiros, Ana Carolina Guimarães; Britto, Constança Felicia de Paoli de Carvalho; Savino, Wilson; Moreira, Otacílio Cruz; Rodrigues, Virmondes; Montano, Nicola; Lages-Silva, Eliane; Ramirez, Luis Eduardo; da Silva, Valdo Jose Dias

2014-01-01

The aim of the present study was to assess the effects of an anticholinesterase agent, pyridostigmine bromide (Pyrido), on experimental chronic Chagas heart disease in mice. To this end, male C57BL/6J mice noninfected (control:Con) or chronically infected (5 months) with Trypanosoma cruzi (chagasic:Chg) were treated or not (NT) with Pyrido for one month. At the end of this period, electrocardiogram (ECG); cardiac autonomic function; heart histopathology; serum cytokines; and the presence of blood and tissue parasites by means of immunohistochemistry and PCR were assessed. In NT-Chg mice, significant changes in the electrocardiographic, autonomic, and cardiac histopathological profiles were observed confirming a chronic inflammatory response. Treatment with Pyrido in Chagasic mice caused a significant reduction of myocardial inflammatory infiltration, fibrosis, and hypertrophy, which was accompanied by a decrease in serum levels of IFNγ with no change in IL-10 levels, suggesting a shift of immune response toward an anti-inflammatory profile. Lower nondifferent numbers of parasite DNA copies were observed in both treated and nontreated chagasic mice. In conclusion, our findings confirm the marked neuroimmunomodulatory role played by the parasympathetic autonomic nervous system in the evolution of the inflammatory-immune response to T. cruzi during experimental chronic Chagas heart disease in mice.

Modification of Montmorillonite with Cetyl Trimethylammonium Bromide and Tetra Ethyl Ortho Silicate

NASA Astrophysics Data System (ADS)

Widjonarko, D. M.; Mayasari, O. D.; Wahyuningsih, S.; Nugrahaningtyas, K. D.

2018-03-01

Modification of montmorillonite (MMt) with cetyltrimethylammonium bromide (CTAB) and tetraethyl ortosilicate (TEOS) has been done. The aim of the research is to study the effect of TEOS and CTAB into MMt. This research is a preliminary step to invent material that can be modified with other functional materials. The study was conducted by recting TEOS with MMt and varying CTAB concentration on MMt previously modified with TEOS. The TEOS concentration was 4.72 M while CTAB concentration was 0.25; 0.5; 2; 3.5; and 5 mmol/g in MMt which has been reacted with TEOS. Material characterization was done by X-Ray Diffraction (XRD), Fourrier Transform Infra-Red Spectrophotometer (FTIR) and Scanning Electron Microscope (SEM). Cation exchange capacity (CEC) of materials was analyzed by titration method. The results show that TEOS and CTAB successfully modified. TEOS adsorbed onto MMt. It was identified from increased basal spacing, specific group and also by its elemental composition, originally having basal spacing 16 Å. After modification with CTAB, basal spacing increased to 28.45 Å or 77.64%. This indicates that CTAB is intercalated within the MMt layers. The CEC of new material is 0.93 meq/g, increase from 0.83 meq/g.

Physics of lithium bromide (LiBr) solution dewatering through vapor venting membranes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Isfahani, RN; Fazeli, A; Bigham, S

2014-01-01

The physics of water desorption from a lithium bromide (LiBr) solution flow through an array of microchannels capped by a porous membrane is studied. The membrane allows the vapor to exit the flow and retains the liquid. Effects of different parameters such as wall temperature, solution and vapor pressures, and solution mass flux on the desorption rate were studied. Two different mechanisms of desorption are analyzed. These mechanisms consisted of: (1) direct diffusion of water molecules out of the solution and their subsequent flow through the membrane and (2) formation of water vapor bubbles within the solution and their ventingmore » through the membrane. Direct diffusion was the dominant desorption mode at low surface temperatures and its magnitude was directly related to the vapor pressure, the solution concentration, and the heated wall temperature. Desorption at the boiling regime was predominantly controlled by the solution flow pressure and mass flux. Microscale visualization studies suggested that at a critical mass flux, some bubbles are carried out of the desorber through the solution microchannels rather than being vented through the membrane. Overall, an order of magnitude higher desorption rate compare to a previous study on a membrane-based desorber was achieved. Published by Elsevier Ltd.« less

Ethidium bromide as a marker of mtDNA replication in living cells

NASA Astrophysics Data System (ADS)

Villa, Anna Maria; Fusi, Paola; Pastori, Valentina; Amicarelli, Giulia; Pozzi, Chiara; Adlerstein, Daniel; Doglia, Silvia Maria

2012-04-01

Mitochondrial DNA (mtDNA) in tumor cells was found to play an important role in maintaining the malignant phenotype. Using laser scanning confocal fluorescence microscopy (LSCFM) in a recent work, we reported a variable fluorescence intensity of ethidium bromide (EB) in mitochondria nucleoids of living carcinoma cells. Since when EB is bound to nucleic acids its fluorescence is intensified; a higher EB fluorescence intensity could reflect a higher DNA accessibility to EB, suggesting a higher mtDNA replication activity. To prove this hypothesis, in the present work we studied, by LSCFM, the EB fluorescence in mitochondria nucleoids of living neuroblastoma cells, a model system in which differentiation affects the level of mtDNA replication. A drastic decrease of fluorescence was observed after differentiation. To correlate EB fluorescence intensity to the mtDNA replication state, we evaluated the mtDNA nascent strands content by ligation-mediated real-time PCR, and we found a halved amount of replicating mtDNA molecules in differentiating cells. A similar result was obtained by BrdU incorporation. These results indicate that the low EB fluorescence of nucleoids in differentiated cells is correlated to a low content of replicating mtDNA, suggesting that EB may be used as a marker of mtDNA replication in living cells.

Clinical potential of aclidinium bromide in chronic obstructive pulmonary disease.

PubMed

Jones, Paul W

2015-01-01

Three long-acting muscarinic antagonists (LAMAs) are now available in Europe, providing clinicians and patients with a choice of interventions, which is important in COPD, which is clinically a heterogeneous disease. The first LAMA, tiotropium, has been widely used over the last decade as a once-daily maintenance therapy in stable COPD to improve patients' health-related quality of life and to reduce the risk of exacerbations. Administered via the HandiHaler(®) device, it is safe and well tolerated. Another new once-daily LAMA, glycopyrronium, has also been shown to improve health status and reduce exacerbations, and is well tolerated. The subject of this review is a third LAMA, aclidinium bromide, which was approved as a twice-daily maintenance bronchodilator treatment. In the pivotal Phase III clinical trials, patients receiving aclidinium achieved significantly greater improvements in lung function, reductions in breathlessness, and improvements in health status compared with placebo, for up to 24 weeks. In continuation studies, these improvements were sustained for up to 52 weeks. Pooled data showed exacerbation frequency was significantly reduced with aclidinium versus placebo. Preclinical and pharmacological studies demonstrating low systemic bioavailability and a low propensity to induce cardiac arrhythmias were translated into a favorable tolerability profile in the clinical trial program - the adverse event profile of aclidinium was similar to placebo, with a low incidence of anticholinergic and cardiac adverse events. While additional studies are needed to evaluate its full clinical potential, aclidinium is an important part of this recent expansion of LAMA therapeutic options, providing clinicians and patients with an effective and well-tolerated COPD treatment.

Depleting methyl bromide residues in soil by reaction with bases.

PubMed

Xuan, Richeng; Ashworth, Daniel J; Luo, Lifang; Wang, Haizhen; Yates, Scott R

2010-12-01

Despite generally being considered the most effective soil fumigant, methyl bromide (MeBr) use is being phased out because its emissions from soil can lead to stratospheric ozone depletion. However, a large amount is still currently used due to Critical Use Exemptions. As strategies for reducing the postfumigation emissions of MeBr from soil, Ca(OH)(2), K(2)CO(3), and NH(3) were assessed as means of promoting MeBr degradation. Ammonia aqueous solution (NH(4)OH) was the most effective, because MeBr can be degraded by both hydrolysis and ammonolysis. At 20 °C, the half-lives (t(1/2)) of MeBr were 18.0, 2.5, and 1.3 h in 0.1, 1.0, and 2.0 M NH(4)OH, respectively. In 1.0 M NH(4)OH, increasing the solution temperature to 40 °C reduced the half-life of MeBr to 0.23 h. Ammonia amendment to moist soil also promoted MeBr transformation, and the MeBr degradation rate increased with increasing soil temperature. NH(4)OH (30%, 16 M) very effectively reacted with MeBr that was contained under plastic film. Under Hytibar (a virtually impermeable film, VIF), over 99.5% of the MeBr could be destroyed by 30% NH(4)OH in 8 h at 20 °C. On the basis of these results, good management practices (i.e., VIF plus NH(4)OH) could be developed for continued use of MeBr as a soil fumigant under Critical Use Exemptions, without significant emissions.

Dicationic Alkylammonium Bromide Gemini Surfactants. Membrane Perturbation and Skin Irritation

PubMed Central

Almeida, João A. S.; Faneca, Henrique; Carvalho, Rui A.; Marques, Eduardo F.; Pais, Alberto A. C. C.

2011-01-01

Dicationic alkylammonium bromide gemini surfactants represent a class of amphiphiles potentially effective as skin permeation enhancers. However, only a limited number of studies has been dedicated to the evaluation of the respective cytotoxicity, and none directed to skin irritation endpoints. Supported on a cell viability study, the cytotoxicity of gemini surfactants of variable tail and spacer length was assessed. For this purpose, keratinocyte cells from human skin (NCTC 2544 cell line), frequently used as a model for skin irritation, were employed. The impact of the different gemini surfactants on the permeability and morphology of model vesicles was additionally investigated by measuring the leakage of calcein fluorescent dye and analyzing the NMR spectra of 31P, respectively. Detail on the interaction of gemini molecules with model membranes was also provided by a systematic differential scanning calorimetry (DSC) and molecular dynamics (MD) simulation. An irreversible impact on the viability of the NCTC 2544 cell line was observed for gemini concentrations higher than 25 mM, while no cytotoxicity was found for any of the surfactants in a concentration range up to 10 mM. A higher cytotoxicity was also found for gemini surfactants presenting longer spacer and shorter tails. The same trend was obtained in the calorimetric and permeability studies, with the gemini of longest spacer promoting the highest degree of membrane destabilization. Additional structural and dynamical characterization of the various systems, obtained by 31P NMR and MD, provide some insight on the relationship between the architecture of gemini surfactants and the respective perturbation mechanism. PMID:22102870

Bacterial oxidation of methyl bromide in fumigated agricultural soils

USGS Publications Warehouse

Miller, L.G.; Connell, T.L.; Guidetti, J.R.; Oremland, R.S.

1997-01-01

The oxidation of [14C]methyl bromide ([14C]MeBr) to 14CO2 was measured in field experiments with soils collected from two strawberry plots fumigated with mixtures of MeBr and chloropicrin (CCI3NO2). Although these fumigants are considered potent biocides, we found that the highest rates of MeBr oxidation occurred 1 to 2 days after injection when the fields were tarped, rather than before or several days after injection. No oxidation of MeBr occurred in heat-killed soils, indicating that microbes were the causative agents of the oxidation. Degradation of MeBr by chemical and/or biological processes accounted for 20 to 50% of the loss of MeBr during fumigation, with evasion to the atmosphere inferred to comprise the remainder. In laboratory incubations, complete removal of [14C]MeBr occurred within a few days, with 47 to 67% of the added MeBr oxidized to 14CO2 and the remainder of counts associated with the solid phase. Chloropicrin inhibited the oxidation of MeBr, implying that use of this substance constrains the extent of microbial degradation of MeBr during fumigation. Oxidation was by direct bacterial attack of MeBr and not of methanol, a product of the chemical hydrolysis of MeBr. Neither nitrifying nor methane-oxidizing bacteria were sufficiently active in these soils to account for the observed oxidation of MeBr, nor could the microbial degradation of MeBr be linked to cooxidation with exogenously supplied electron donors. However, repeated addition of MeBr to live soils resulted in higher rates of its removal, suggesting that soil bacteria used MeBr as an electron donor for growth. To support this interpretation, we isolated a gram-negative, aerobic bacterium from these soils which grew with MeBr as a sole source of carbon and energy.

Ultraviolet quantum detection efficiency of potassium bromide as an opaque photocathode applied to microchannel plates

NASA Technical Reports Server (NTRS)

Siegmund, Oswald H. W.; Everman, E.; Vallerga, J. V.; Sokolowski, J.; Lampton, M.

1987-01-01

The quantum detection efficiency (QDE) of potassium bromide as a photocathode applied directly to the surface of a microchannel plate over the 250-1600 A wavelength range has been measured. The contributions of the photocathode material in the channels and on the interchannel web to the QDE have been determined. Two broad peaks in the QDE centered at about 450 and about 1050 A are apparent, the former with about 50 percent peak QDE and the latter with about 40 percent peak QDE. The photoelectric threshold is observed at about 1600 A, and there is a narrow QDE minimum at about 750 A which correlates with 2X the band gap energy for KBr. The angular variation of the QDE from 0 to 40 deg to the channnel axis has also been examined. The stability of Kbr with time is shown to be good with no significant degradation of QDE at wavelengths below 1216 A over a 15-day period in air.

Permanganate-bromide-silver nanoparticles as a new chemiluminescence system and its application to captopril determination.

PubMed

Amjadi, Mohammad; Manzoori, Jamshid L; Hassanzadeh, Javad; Sorouraddin, Mohammad H

2013-10-15

A novel chemiluminescence (CL) system based on the oxidation of bromide by permanganate in sulfuric acid medium is introduced. The enhancing effect of silver nanoparticles (NPs), synthesized by chemical reduction method, on this reaction was studied. It was demonstrated that spherical silver nanoparticles with average size of 18 nm had a most remarkable catalytic effect on this reaction. CL emission wavelengths and UV-vis spectra were used to characterize the system and propose a possible mechanism. Furthermore, it was found that captopril inhibits the action of NPs and decreases the intensity of CL. Based on this phenomenon, a new CL method was developed for the determination of captopril in the 3.0 × 10(-10) to 1.0 × 10(-7) mol L(-1) concentration range with a detection limit (3s) of 0.12 nmol L(-1). The method was successfully applied to the determination of captopril in pharmaceutical formulations, human urine and serum samples. Copyright © 2013 Elsevier B.V. All rights reserved.

Enhancement of methylbenzene adsorption capacity through cetyl trimethyl ammonium bromide-modified activated carbon derived from Astragalus residue

NASA Astrophysics Data System (ADS)

Feng, Ningchuan; Zhang, Yumei; Fan, Wei; Zhu, Meilin

2018-02-01

Activated carbon was prepared from astragalus residue by KOH and then treated with cetyl trimethyl ammonium bromide (CTAB) and used for the removal of methylbenzene from aqueous solution. The samples were characterized by FTIR, XRD, SEM and Boehm titration. The results showed that CTAB changed the physicochemical properties of activated carbon significantly. The isotherm adsorption studies of methylbenzene onto the astragalus residue activated carbon (ASC) and CTAB-modified astragalus residue activated carbon (ASCCTAB) were examined by using batch techniques and agreed well with the Langmuir model. The maximum adsorption capacity of ASC and ASC-CTAB for methylbenzene determined from the Langmuir model was183.56 mg/g and 235.18 mg/g, respectively. The results indicated that using CTAB as a modifier for ASC modification could markedly enhance the methylbenzene removal from water.

Side effects of low-dose pyridostigmine bromide are not related to cholinesterase inhibition.

PubMed

Cook, M R; Gerkovich, M M; Sastre, A; Graham, C

2001-12-01

Pretreatment with pyridostigmine bromide (PB) has become part of standard military procedures for protection against the effects of possible chemical warfare attack. The purpose of the work reported here was to quantify the type, intensity and frequency of side effects of low-dose PB, and to examine factors that predict the intensity and frequency of side effects. A double-blind, cross-over, placebo (PL)-controlled design was used. Of the 67 subjects, 33 received 30 mg PB every 8 h for 13 doses, and 34 received 60 mg on the same schedule. Order of PB and PL administration was counterbalanced. Overall, side effects were mild, even at the 60-mg dose level. More side effects were reported when volunteers were taking PB than when they were taking placebo. Women reported more symptoms than men. Neither cholinesterase inhibition nor plasma levels of PB predicted side effect scores during the PB week; the best predictor of side effect scores during the PB week was side effect scores during the PL week. PB is well tolerated by healthy young people, even when twice the recommended military dose is administered.

Characterization of Thallium Bromide Detectors Made From Material Purified by the Filter Method

NASA Astrophysics Data System (ADS)

Onodera, Toshiyuki; Hitomi, Keitaro; Tada, Tsutomu; Shoji, Tadayoshi; Mochizuki, Katsumi

2013-10-01

Thallium bromide (TlBr) has been regarded as candidate detector materials for the gamma-ray spectrometers operating at room temperature. In this study, a simple and rapid method, the filter method, was performed to purify a raw TlBr material used for fabrication of TlBr detectors. The material was loaded on shards of crashed quartz and installed in a Pyrex tube, and was melted using a furnace. A purified material passing through interspaces of the shards of quartz was collected in a quartz ampoule located at the outlet of the Pyrex tube. After the purification, impurities colored black extracted from the raw material remained. TlBr crystals were then grown by the travelling molten zone method both from the raw material and the purified material. TlBr detectors were fabricated from the grown crystals, and were characterized by measuring mobility-lifetime products (μτ) for carriers and gamma-ray spectra ( 137Cs) at room temperature. μτ for electrons of a TlBr detector fabricated from the purified material was around 5 times higher than that of a detector fabricated from the raw material.

The blocking action of choline 2:6-xylyl ether bromide on adrenergic nerves

PubMed Central

Exley, K. A.

1957-01-01

Choline 2:6-xylyl ether bromide (TM 10), given systemically to cats in doses of 5 to 15 mg./kg., abolishes the effects of adrenergic nerve stimulation whilst leaving the reactions of the effector organs to adrenaline unimpaired. The effects of a single dose may take up to one hour to become fully established and last for more than twenty-four hours. Apart from transitory ganglionic blockade, cholinergic autonomic nerves are unaffected even by large doses of TM 10. Doses of TM 10 which produce effective blockade do not impair conduction along adrenergic nerve trunks; the drug must, therefore, act at, or close to, the nerve terminals. TM 10 prevents the output of noradrenaline from the spleen on stimulating the splenic nerves; but, in acute experiments, it does not influence the liberation of pressor amines from the stimulated suprarenals. Examination of some ethers related to TM 10 revealed no correlation between TM 10-like adrenergic blocking activity and local anaesthetic activity. The action of TM 10 on adrenergic nerves does not, therefore, seem to be accounted for by axonal block. ImagesFIG. 8 PMID:13460234

Determination of residual nonsteroidal anti-inflammatory drugs in aqueous sample using magnetic nanoparticles modified with cetyltrimethylammonium bromide by high performance liquid chromatography.

PubMed

Khoeini Sharifabadi, Malihe; Saber-Tehrani, Mohammad; Waqif Husain, Syed; Mehdinia, Ali; Aberoomand-Azar, Parviz

2014-01-01

A simple and sensitive solid-phase extraction method for separation and preconcentration of trace amount of four nonsteroidal anti-inflammatory drugs (naproxen, indomethacin, diclofenac, and ibuprofen) using Fe3O4 magnetic nanoparticles modified with cetyltrimethylammonium bromide has been developed. For this purpose, the surface of MNPs was modified with cetyltrimethylammonium bromide (CTAB) as a cationic surfactant. Effects of different parameters influencing the extraction efficiency of drugs including the pH, amount of salt, shaking time, eluent type, the volume of solvent, amount of adsorbent, sample volume, and the time of desorption were investigated and optimized. Methanol has been used as desorption solvent and the extracts were analysed on a reversed-phase octadecyl silica column using 0.02 M phosphate-buffer (pH = 6.02) acetonitrile (65 : 35 v/v) as the mobile phase and the effluents were measured at 202 nm with ultraviolet detector. The relative standard deviation (RSD%) of the method was investigated at three concentrations (25, 50, and 200 ng/mL) and was in the range of 3.98-9.83% (n = 6) for 50 ng/mL. The calibration curves obtained for studied drugs show reasonable linearity (R (2) > 0.99) and the limit of detection (LODs) ranged between 2 and 7 ng/mL. Finally, the proposed method has been effectively employed in extraction and determination of the drugs in biological and environmental samples.

Micellar and analytical implications of a new potentiometric PVC sensor based on neutral ion-pair complexes of dodecylmethylimidazolium bromide-sodium dodecylsulfate.

PubMed

Sanan, Reshu; Mahajan, Rakesh Kumar

2013-03-15

With an aim to characterize the micellar aggregates of imidazolium based ionic liquids, a new potentiometric PVC sensor based on neutral ion-pair complexes of dodecylmethylimidazolium bromide-sodium dodecylsulfate (C12MeIm(+)DS(-)) has been developed. The electrode exhibited a linear response for the concentration range of 7.9×10(-5)-9.8×10(-3) M with a super-Nernstian slope of 92.94 mV/decade, a response time of 5 s and critical micellar concentration (cmc) of 10.09 mM for C12MeImBr. The performance of the electrode in investigating the cmc of C12MeImBr in the presence of two drugs [promazine hydrochloride (PMZ) and promethazine hydrochloride (PMT)] and three triblock copolymers (P123, L64 and F68) has been found to be satisfactory on comparison with conductivity measurements. Various micellar parameters have been evaluated for the binary mixtures of C12MeImBr with drugs and triblock copolymers using Clint's, Rubingh's, and Motomura's approach. Thus the electrode offers a simple, straightforward and relatively fast technique for the characterization of micellar aggregates of C12MeImBr, complementing existing conventional techniques. Further, the analytical importance of proposed C12MeIm(+)-ISE as end point indicator in potentiometric titrations and for direct determination of cationic surfactants [cetylpyridinium chloride (CPC), tetradecyltrimethylammonium bromide (TTAB), benzalkonium chloride (BC)] in some commercial products was judged by comparing statistically with classical two-phase titration methods. Copyright © 2013 Elsevier Inc. All rights reserved.

Persistent modification of Na{sub v}1.9 following chronic exposure to insecticides and pyridostigmine bromide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nutter, Thomas J., E-mail: tnutter@dental.ufl.edu; Cooper, Brian Y., E-mail: bcooper@dental.ufl.edu

Many veterans of the 1991 Gulf War (GW) returned from that conflict with a widespread chronic pain affecting deep tissues. Recently, we have shown that a 60 day exposure to the insecticides permethrin, chlorpyrifos, and pyridostigmine bromide (NTPB) had little influence on nociceptor action potential forming Na{sub v}1.8, but increased K{sub v}7 mediated inhibitory currents 8 weeks after treatment. Using the same exposure regimen, we used whole cell patch methods to examine whether the influences of NTPB could be observed on Na{sub v}1.9 expressed in muscle and vascular nociceptors. During a 60 day exposure to NTPB, rats exhibited lowered musclemore » pain thresholds and increased rest periods, but these measures subsequently returned to normal levels. Eight and 12 weeks after treatments ceased, DRG neurons were excised from the sensory ganglia. Whole cell patch studies revealed little change in voltage dependent activation and deactivation of Na{sub v}1.9, but significant increases in the amplitude of Na{sub v}1.9 were observed 8 weeks after exposure. Cellular studies, at the 8 week delay, revealed that NTPB also significantly prolonged action potential duration and afterhyperpolarization (22 °C). Acute application of permethrin (10 μM) also increased the amplitude of Na{sub v}1.9 in skin, muscle and vascular nociceptors. In conclusion, chronic exposure to Gulf War agents produced long term changes in the amplitude of Na{sub v}1.9 expressed in muscle and vascular nociceptors. The reported increases in K{sub v}7 amplitude may have been an adaptive response to increased Na{sub v}1.9, and effectively suppressed behavioral pain measures in the post treatment period. Factors that alter the balance between Na{sub v}1.9 and K{sub v}7 could release spontaneous discharge and produce chronic deep tissue pain. - Highlights: • Rats were treated 60 days with permethrin, chlorpyrifos and pyridostigmine bromide. • 8 weeks after treatments, Nav1.9 activation and

Effects of aquatic exercises in a rat model of brainstem demyelination with ethidium bromide on the beam walking test.

PubMed

Nassar, Cíntia Cristina Souza; Bondan, Eduardo Fernandes; Alouche, Sandra Regina

2009-09-01

Multiple sclerosis is a demyelinating disease of the central nervous system associated with varied levels of disability. The impact of early physiotherapeutic interventions in the disease progression is unknown. We used an experimental model of demyelination with the gliotoxic agent ethidium bromide and early aquatic exercises to evaluate the motor performance of the animals. We quantified the number of footsteps and errors during the beam walking test. The demyelinated animals walked fewer steps with a greater number of errors than the control group. The demyelinated animals that performed aquatic exercises presented a better motor performance than those that did not exercise. Therefore aquatic exercising was beneficial to the motor performance of rats in this experimental model of demyelination.

Intranasal ipratropium bromide for the common cold.

PubMed

AlBalawi, Zaina H; Othman, Sahar S; Alfaleh, Khalid

2013-06-19

The common cold is one of the most common illnesses in humans and constitutes an economic burden both in terms of productivity and expenditure for treatment. There is no proven cure for the common cold and symptomatic relief is the mainstay of treatment. The use of intranasal ipratropium bromide (IB) has been addressed in several studies and might prove an effective treatment for the common cold. To determine the effect of IB versus placebo or no treatment on severity of rhinorrhoea and nasal congestion in children and adults with the common cold. Subjective overall improvement was another primary outcome and side effects (for example, dry mucous membranes, epistaxis and systemic anticholinergic effects) were reported as a secondary outcome. In this updated review we searched CENTRAL 2013, Issue 3, MEDLINE (1950 to March week 4, 2013), MEDLINE in-process and other non-indexed citations (8 April 2013), EMBASE (1974 to April 2013), AMED (1985 to April 2013), Biosis (1974 to February 2011) and LILACS (1985 to April 2013). Randomised controlled trials (RCTs) comparing IB to placebo or no treatment in children and adults with the common cold. Two review authors independently extracted data and assessed trial quality. We used a standardised form to extract relevant data and we contacted trial authors for additional information. Seven trials with a total of 2144 participants were included. Four studies (1959 participants) addressed subjective change in severity of rhinorrhoea. All studies were consistent in reporting statistically significant changes in favour of IB. Nasal congestion was reported in four studies and was found to have no significant change between the two groups. Two studies found a positive response in the IB group for the global assessment of overall improvement. Side effects were more frequent in the IB group, odds ratio (OR) 2.09 (95% confidence interval (CI) 1.40 to 3.11). Commonly encountered side effects included nasal dryness, blood tinged mucus

Intranasal ipratropium bromide for the common cold.

PubMed

Albalawi, Zaina H; Othman, Sahar S; Alfaleh, Khalid

2011-07-06

The common cold is one of the most common illnesses in humans and constitutes an economic burden both in terms of productivity and expenditure for treatment. There is no proven cure for the common cold and symptomatic relief is the mainstay of treatment. The use of intranasal ipratropium bromide (IB) has been addressed in several studies and might prove an effective treatment for the common cold. To determine the effect of IB versus placebo or no treatment on severity of rhinorrhoea and nasal congestion in children and adults with the common cold. Subjective overall improvement was another primary outcome and side effects were reported as a secondary outcome. We searched the Cochrane Central Register of Controlled Trials (CENTRAL 2011, Issue 1) which contains the Acute Respiratory Infections Group's Specialised Register, MEDLINE (1950 to January week 4, 2011), MEDLINE in-process and other non-indexed citations (February 2011), EMBASE (1974 to February 2011), AMED (1985 to February 2011), Biosis (1974 to February 2011) and LILACS (1985 to February 2011). Randomised controlled trials (RCTs) comparing IB to placebo or no treatment in children and adults with the common cold. Two review authors independently extracted data and assessed trial quality. We used a standardised form to extract relevant data and we contacted trial authors for additional information. Seven trials with a total of 2144 participants were included. Four studies (1959 participants) addressed subjective change in severity of rhinorrhoea. All studies were consistent in reporting statistically significant changes in favour of IB. Nasal congestion was reported in four studies and was found to have no significant change between the two groups. Two studies found a positive response in the IB group for the global assessment of overall improvement. Side effects were more frequent in the IB group, odds ratio (OR) 2.09 (95% confidence interval (CI) 1.40 to 3.11). Commonly encountered side effects included

Stable bromine isotopic composition of methyl bromide released from plant matter

NASA Astrophysics Data System (ADS)

Horst, Axel; Holmstrand, Henry; Andersson, Per; Thornton, Brett F.; Wishkerman, Asher; Keppler, Frank; Gustafsson, Örjan

2014-01-01

Methyl bromide (CH3Br) emitted from plants constitutes a natural source of bromine to the atmosphere, and is a component in the currently unbalanced global CH3Br budget. In the stratosphere, CH3Br contributes to ozone loss processes. Studies of stable isotope composition may reduce uncertainties in the atmospheric CH3Br budget, but require well-constrained isotope fingerprints of the source end members. Here we report the first measurements of stable bromine isotopes (δ81Br) in CH3Br from abiotic plant emissions. Incubations of both KBr-fortified pectin, a ubiquitous cell-stabilizing macromolecule, and of a natural halophyte (Salicornia fruticosa), yielded an enrichment factor (ε) of -2.00 ± 0.23‰ (1σ, n = 8) for pectin and -1.82 ± 0.02‰ (1σ, n = 4) for Salicornia (the relative amount of the heavier 81Br was decreased in CH3Br compared to the substrate salt). For short incubations, and up to 10% consumption of the salt substrate, this isotope effect was similar for temperatures from 30 up to 300 °C. For longer incubations of up to 90 h at 180 °C the δ81Br values increased from -2‰ to 0‰ for pectin and to -1‰ for Salicornia. These δ81Br source signatures of CH3Br formation from plant matter combine with similar data for carbon isotopes to facilitate multidimensional isotope diagnostics of the CH3Br budget.

Effects of cetyltriethylammonium bromide on the replication of Bombyx mori nucleopolyhedrovirus.

PubMed

Zhou, Yajing; Zhang, Zhifang; He, Jialu; Zhang, Yuanxing

2002-05-01

An experimental study was undertaken to quantify the effects of cetyltriethylammonium bromide (CTAB) on the replication of Bombyx mori nucleopolyhedrovirus (BmNPV) and the transcriptionalactivity of BmNPV ie-1 promoter. The results demonstrated that the budded virus (BV) titer rose about 3.7-fold by adding CTAB to the culture media up to 0.1 mu g ml(-1) in infected Bm-N cells with a wild-type BmNPV. The transient expression level of luciferase driven by BmNPV ie-1 promoter was enhanced by more than 3-fold in the presence of 0.1 mu g ml(-1) of CTAB in uninfected insect cells via a transient expression system. Contrary to the rise in BV titer, the polyhedra inside the nucleus of infected cells dropped linearly from 4.0 x 10(6) ml(-1) down to 2.1 x 10(6) ml(-1) with in a range of CTAB concentrations from 0 to 0.25 mu g ml(-1). The same trend in expression level of beta -galactosidase or phytase was given when the Bm-N cells or fifth-instar silkworm larvae infected with a recombinant BmNPV containing the beta -galactosidase or phytase reporter gene driven by the polyhedrin promoter. We deduced that CTAB appeared to affect the virus bi-phasic life cycle stages and production pathways, resulting in an enhancement in BV production and a suppression of occluded virus (OV) production and expression of foreign genes controlled by the polyhedrin promoter.

Study of the Formation and Solution Properties of Worm-Like Micelles Formed Using Both N-Hexadecyl-N-Methylpiperidinium Bromide-Based Cationic Surfactant and Anionic Surfactant

PubMed Central

Yan, Zhihu; Dai, Caili; Feng, Haishun; Liu, Yifei; Wang, Shilu

2014-01-01

The viscoelastic properties of worm-like micelles formed by mixing the cationic surfactant N-hexadecyl-N-methylpiperidinium bromide (C16MDB) with the anionic surfactant sodium laurate (SL) in aqueous solutions were investigated using rheological measurements. The effects of sodium laurate and temperature on the worm-like micelles and the mechanism of the observed shear thinning phenomenon and pseudoplastic behavior were systematically investigated. Additionally, cryogenic transmission electron microscopy images further ascertained existence of entangled worm-like micelles. PMID:25296131

Antibacterial Effect and Tensile Bond Strength of Self-etching Adhesive Resins with and without Methacryloyloxydodecylpyridinium Bromide: An in vitro Study.

PubMed

Krishnamurthy, Madhuram; Kumar, V Naveen; Leburu, Ashok; Dhanavel, Chakravarthy; Selvendran, Kasiswamy E; Praveen, Nehrudhas

2018-04-01

Aim: The aim of the present study was to compare the antibacterial activity of a self-etching primer containing antibacterial monomer methacryloyloxydodecylpyridinium bromide (MDPB) (Clearfil protect bond) with a conventional self-etching primer without MDPB (Clearfil SE bond) against Streptococcus mutans and the effect of incorporation of MDPB on the tensile bond strength of the experimental self-etching primer (Clearfil protect bond). Materials and methods: The antibacterial activity of the self-etching primers was assessed using agar disk diffusion method and the diameters of the zones of inhibition were measured and ranked. For tensile bond strength testing, 20 noncarious human molars were selected and randomly divided into two groups comprising 10 teeth in each group. Group I specimens were treated with Clearfil SE bond (without MDPB). Group II specimens were treated with Clearfil protect bond (with MDPB). Composite material was placed incrementally and cured for 40 seconds in all the specimens. Tensile bond strength was estimated using the Instron Universal testing machine at a crosshead speed of 1 mm/min. Results: The addition of MDPB into a self-etching primer exerts potential antibacterial effect against S. mutans. The tensile bond strength of MDPB containing self-etching primer was slightly lower than that of the conventional self-etching Clearfil protect bond primer, but the difference was not statistically significant. Conclusion: Thus, a self-etching primer containing MDPB will be a boon to adhesive dentistry as it has bactericidal property with adequate tensile bond strength. Clinical significance: The concept of prevention of extension in adhesive dentistry would result in micro/nanoleakage due to the presence of residual bacteria in the cavity. Self-etching primers with MDPB would improve the longevity of such restorations by providing adequate antibacterial activity without compromising the bond strength. Keywords: Antibacterial property

Efficacy and safety of methantheline bromide (Vagantin(®) ) in axillary and palmar hyperhidrosis: results from a multicenter, randomized, placebo-controlled trial.

PubMed

Müller, C; Berensmeier, A; Hamm, H; Dirschka, T; Reich, K; Fischer, T; Rzany, B

2013-10-01

Focal hyperhidrosis can severely affect quality of life. So far, knowledge on the effect of systemic therapy of focal hyperhidrosis is limited. To assess the efficacy and safety of methantheline bromide (MB) in the treatment of axillary and palmar-axillary hyperhidrosis. A multicenter controlled randomized double-blind clinical trial was conducted in patients with axillary or palmar-axillary hyperhidrosis defined by a sweat production >50 mg/5 min. Patients received 3 × 50 mg MB daily or placebo over a period of 28 ± 1 days. Main outcome criterion was the reduction of sweat as measured by gravimetry on day 28 ± 1. Quality of life was assessed by Dermatology Life Quality Index (DLQI) and Hyperhidrosis Disease Severity Score (HDSS). A total of 339 patients were randomly assigned to receive MB or placebo. On day 28 ± 1, the mean axillary sweat production was 99 mg for MB and 130 mg for placebo compared with 168 mg and 161 mg respectively at baseline (P = 0.004). Patient's HDSS score decreased in the MB group from 3.2 to 2.4 compared with 3.2 to 2.7 for placebo (P = 0.002). Similar results could be obtained for the DLQI with 9.7 for MB and 12.2 for placebo, which decreased from 16.4 or 17 respectively (P = 0.003). Tolerability was good for both groups. The most frequent adverse event was dry mouth. Fifty milligrams methantheline bromide three times a day is an effective and safe treatment of axillary hyperhidrosis. © 2012 The Authors. Journal of the European Academy of Dermatology and Venereology © 2012 European Academy of Dermatology and Venereology.

Extracellular biosynthesis of silver nanoparticles: effects of shape-directing cetyltrimethylammonium bromide, pH, sunlight and additives.

PubMed

Hussain, Shokit; Akrema; Rahisuddin; Khan, Zaheer

2014-05-01

The work reported in this paper describes the preparation, morphology, stability and sensitivity of Ag-nanoparticles towards sunlight using Allium sativum, garlic extract for the first time. The synthesized silver particles show an intense surface plasmon resonance band in the visible region at 410 nm. The position of the wavelength maxima, blue and red shift, strongly depends on the sunlight and pH. TEM analysis revealed the presence of spherical, different size (from 5.0 to 30 nm) and garlic constituents bio-conjugated, stabilized and/or layered silver nanoparticles. The concentrations of garlic extract, cetyltrimethylammonium bromide, Ag(+) ions and reaction time play vital roles for nucleus formation and the growth processes. Sulfur-containing biomolecules of extract, especially cysteine, are responsible for the reduction of Ag(+) ions into metallic Ag(0). The agglomeration number of the silver nanoparticles (N Ag) and the average number of free electrons per particle (n fe) are calculated and discussed.

Reverse osmosis membrane composition, structure and performance modification by bisulphite, iron(III), bromide and chlorite exposure.

PubMed

Ferrer, O; Gibert, O; Cortina, J L

2016-10-15

Reverse osmosis (RO) membrane exposure to bisulphite, chlorite, bromide and iron(III) was assessed in terms of membrane composition, structure and performance. Membrane composition was determined by Rutherford backscattering spectrometry (RBS) and membrane performance was assessed by water and chloride permeation, using a modified version of the solution-diffusion model. Iron(III) dosage in presence of bisulphite led to an autooxidation of the latter, probably generating free radicals which damaged the membrane. It comprised a significant raise in chloride passage (chloride permeation coefficient increased 5.3-5.1 fold compared to the virgin membrane under the conditions studied) rapidly. No major differences in terms of water permeability and membrane composition were observed. Nevertheless, an increase in the size of the network pores, and a raise in the fraction of aggregate pores of the polyamide (PA) layer were identified, but no amide bond cleavage was observed. These structural changes were therefore, in accordance with the transport properties observed. Copyright © 2016 Elsevier Ltd. All rights reserved.

Strain IMB-1, a novel bacterium for the removal of methyl bromide in fumigated agricultural soils

USGS Publications Warehouse

Connell, Hancock T.L.; Costello, A.M.; Lidstrom, M.E.; Oremland, R.S.

1998-01-01

A facultatively methylotrophic bacterium, strain IMB-1, that has been isolated from agricultural soil grows on methyl bromide (MeBr), methyl iodide, methyl chloride, and methylated amines, as well as on glucose, pyruvate, or acetate. Phylogenetic analysis of its 16S rRNA gene sequence indicates that strain IMB-1 classes in the alpha subgroup of the class Proteobacteria and is closely related to members of the genus Rhizobium. The ability of strain IMB-1 to oxidize MeBr to CO2 is constitutive in cells regardless of the growth substrate. Addition of cell suspensions of strain IMB-1 to soils greatly accelerates the oxidation of MeBr, as does pretreatment of soils with low concentrations of methyl iodide. These results suggest that soil treatment strategies can be devised whereby bacteria can effectively consume MeBr during field fumigations, which would diminish or eliminate the outward flux of MeBr to the atmosphere.

Behavior of lanthanum containing barium stannate nanoparticles synthesized by cetyltriammonium bromide assisted wet chemistry route

NASA Astrophysics Data System (ADS)

Kumar, Astakala Anil; Kumar, Ashok; Quamara, J. K.

2018-02-01

In present study, we report dielectric, ferroelectric and pyroelectric behavior of pristine and La3+ containing barium stannate nanoparticles synthesized via wet chemical route involving cetyltriammonium bromide assisted thermal decomposition of binary precursors. The X-ray diffraction patterns of pristine and La3+ (2, 4 and 6 at%) doped BaSnO3 nanoparticles showed the formation of cubic perovskite phase. On substitution of Ba2+ lattice sites by La3+ at the La content of 6 at%, the sample exhibited fourfold increase in conductivity in comparison to pristine BaSnO3. Polarization hysteresis (P-E) curves of La containing barium stannate nanoparticles showed anti-ferroelectric behavior. The pyroelectric coefficient of pristine and La (2, 4 and 6 at%) containing BaSnO3 nanoparticles at 473 K were found to be 7.8, 11.6, 14.1 and 17.2 μCm-2K-1, respectively. Further, the responsivity and detectivity values were higher in comparison to the materials, such as AlN, GaN, CdS and ZnO.

A facile electrochemical sensor for nonylphenol determination based on the enhancement effect of cetyltrimethylammonium bromide.

PubMed

Lu, Qing; Zhang, Weina; Wang, Zhihui; Yu, Guangxia; Yuan, Yuan; Zhou, Yikai

2013-01-07

A facile electrochemical sensor for the determination of nonylphenol (NP) was fabricated in this work. Cetyltrimethylammonium bromide (CTAB), which formed a bilayer on the surface of the carbon paste (CP) electrode, displayed a remarkable enhancement effect for the electrochemical oxidation of NP. Moreover, the oxidation peak current of NP at the CTAB/CP electrode demonstrated a linear relationship with NP concentration, which could be applied in the direct determination of NP. Some experimental parameters were investigated, such as external solution pH, mode and time of accumulation, concentration and modification time of CTAB and so on. Under optimized conditions, a wide linear range from 1.0 × 10(-7) mol·L(-1) to 2.5 × 10(-5) mol·L(-1) was obtained for the sensor, with a low limit of detection at 1.0 × 10(-8) mol·L(-1). Several distinguishing advantages of the as-prepared sensor, including facile fabrication, easy operation, low cost and so on, suggest a great potential for its practical applications.

Synthesis, characterization and antibacterial properties of dihydroxy quaternary ammonium salts with long chain alkyl bromides.

PubMed

Liu, Wen-Shuai; Wang, Chun-Hua; Sun, Ju-Feng; Hou, Gui-Ge; Wang, Yu-Peng; Qu, Rong-Jun

2015-01-01

Five N-methyl-N-R-N,N-bis(2-hydroxyethyl) ammonium bromides (R = -benzyl (chloride, BNQAS), -dodecyl (C12QAS), -tetradecyl (C14QAS), -hexadecyl (C16QAS), -octadecyl (C18QAS)) were prepared based on N-methyldiethanolamine (MDEA) and halohydrocarbon. Five QAS were characterized by FTIR, NMR, and MS. BNQAS, C12QAS, C14QAS, and C16QAS were confirmed by X-ray single-crystal diffraction. Their antibacterial properties indicated good antibacterial abilities against E. coli, S. aureus, B. subtilis, especially C12QAS with the best antibacterial ability (100% to E. coli, 95.65% to S. aureus, and 91.41% to B. subtilis). In addition, C12QAS also displayed the best antifungal activities than BNQAS and C18QAS against Cytospora mandshurica, Botryosphaeria ribis, Physalospora piricola, and Glomerella cingulata with the ratio of full marks. The strategy provides a facile way to design and develop new types of antibacterial drugs for application in preventing the fruit rot, especially apple. © 2014 John Wiley & Sons A/S.

Photocontrol of Voltage-Gated Ion Channel Activity by Azobenzene Trimethylammonium Bromide in Neonatal Rat Cardiomyocytes

PubMed Central

Frolova, Sheyda R.; Gaiko, Olga; Tsvelaya, Valeriya A.; Pimenov, Oleg Y.; Agladze, Konstantin I.

2016-01-01

The ability of azobenzene trimethylammonium bromide (azoTAB) to sensitize cardiac tissue excitability to light was recently reported. The dark, thermally relaxed trans- isomer of azoTAB suppressed spontaneous activity and excitation propagation speed, whereas the cis- isomer had no detectable effect on the electrical properties of cardiomyocyte monolayers. As the membrane potential of cardiac cells is mainly controlled by activity of voltage-gated ion channels, this study examined whether the sensitization effect of azoTAB was exerted primarily via the modulation of voltage-gated ion channel activity. The effects of trans- and cis- isomers of azoTAB on voltage-dependent sodium (INav), calcium (ICav), and potassium (IKv) currents in isolated neonatal rat cardiomyocytes were investigated using the whole-cell patch-clamp technique. The experiments showed that azoTAB modulated ion currents, causing suppression of sodium (Na+) and calcium (Ca2+) currents and potentiation of net potassium (K+) currents. This finding confirms that azoTAB-effect on cardiac tissue excitability do indeed result from modulation of voltage-gated ion channels responsible for action potential. PMID:27015602

Effects of Nonhydrostatic Stress on Structural and Optoelectronic Properties of Methylammonium Lead Bromide Perovskite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Rong; Cai, Weizhao; Bi, Tiange

We report synchrotron X-ray diffraction, photoconductivity, and photoluminescence investigations of methylammonium-lead-bromide (MAPbBr3) under various stress conditions, supported by density-functional-theory (DFT) calculations. The properties of MAPbBr3 show substantial dependence on the hydrostatic conditions. While nonhydrostatic compression of MAPbBr3 leads to amorphization above 2.4 GPa, under quasi-hydrostatic (Ar) and hydrostatic (He) pressure, the sample remains in crystalline phases. A sequence of phase transitions between two cubic phases and orthorhombic Pnma phase is observed when using Ar, or no pressure-transmitting-medium (PTM). In helium-PTM only transitions between the two cubic structures and a new isostructural phase transition with a large volume collapse to amore » third cubic-phase at 2.7 GPa was observed. The photoluminescence measurements indicate a pressure-induced band gap-narrowing in the cubic phase I, and a blue-shift in the orthorhombic structure. DFT calculations illustrate that the dynamics of the organic molecules and the inorganic lattice, coupled via the N–H···Br hydrogen-bonding interactions, affect the Pb–Br distance and the bandgap evolution under pressure.« less

Colorimetric susceptibility testing for Aspergillus fumigatus: comparison of menadione-augmented 3-(4,5-dimethyl-2-thiazolyl)-2,5-diphenyl-2H-tetrazolium bromide and Alamar blue tests.

PubMed Central

Jahn, B; Stüben, A; Bhakdi, S

1996-01-01

Two colorimetric methods that use Alamar Blue or 3-(4,5-dimethyl-2-thiazolyl)-2,5-diphenyl-2H-tetrazolium bromide (MTT) for assaying the in vitro activities of antifungal agents have been described. We report that both tests performed similarly when the antifungal activity of amphotericin B against Candida albicans was determined. However, only the MTT test generated interpretable data when Aspergillus fumigatus was used. PMID:8818910

Transport of atrazine versus bromide and δO18 in sand

USGS Publications Warehouse

Tindall, James A.; Friedel, Michael J.

2016-01-01

The objective of this research was to determine the process of atrazine transport compared to bromide and δO18 transport in sands near Denver. Three 1.5 × 2 × 1.5-m plots were installed and allowed to equilibrate for 2 years before research initiation and were instrumented with 1.5 × 2-m zero-tension pan lysimeters installed at 1.5-m depths. Additionally, each plot was instrumented with suction lysimeters, tensiometers, time domain reflectometry (TDR) moisture probes, and thermocouples (to measure soil temperature) at 15-cm depth increments. All plots were enclosed with a raised frame (of 8-cm height) to prevent surface runoff. During the 2-year period before research began, all suction and pan lysimeters were purged monthly and were sampled for fluids immediately prior to atrazine and KBr application to obtain background concentrations. Atrazine illustrated little movement until after a significant rainfall event, which peaked concentrations at depths of about 90 to 135 cm. Both Br− and δO18 moved rapidly through the soil, probably owing to soil porosity and anion exclusion for Br−. Concentrations of atrazine exceeding 5.0 μL−1 were observed with depth (90 to 150 cm) after several months. It appears that significant rainfall events were a key factor in the movement of atrazine in the sand, which allowed the chemicals to move to greater depths and thus avoid generally found biodegradation processes.

Influence of surface roughness on cetyltrimethylammonium bromide adsorption from aqueous solution.

PubMed

Wu, Shuqing; Shi, Liu; Garfield, Lucas B; Tabor, Rico F; Striolo, Alberto; Grady, Brian P

2011-05-17

The influence of surface roughness on surfactant adsorption was studied using a quartz crystal microbalance with dissipation (QCM-D). The sensors employed had root-mean-square (R) roughness values of 2.3, 3.1, and 5.8 nm, corresponding to fractal-calculated surface area ratios (actual/nominal) of 1.13, 1.73, and 2.53, respectively. Adsorption isotherms measured at 25 °C showed that adsorbed mass of cetyltrimethylammonium bromide per unit of actual surface area below 0.8 cmc, or above 1.2 cmc, decreases as the surface roughness increases. At the cmc, both the measured adsorbed amount and the measured dissipation increased dramatically on the rougher surfaces. These results are consistent with the presence of impurities, suggesting that roughness exacerbates well-known phenomena reported in the literature of peak impurity-related adsorption at the cmc. The magnitude of the increase, especially in dissipation, suggests that changes in adsorbed amount may not be the only reason for the observed results, as aggregates at the cmc on rougher surfaces are more flexible and likely contain larger amounts of solvent. Differences in adsorption kinetics were also found as a function of surface roughness, with data showing a second, slower adsorption rate after rapid initial adsorption. A two-rate Langmuir model was used to further examine this effect. Although adsorption completes faster on the smoother surfaces, initial adsorption at zero surface coverage is faster on the rougher surfaces, suggesting the presence of more high-energy sites on the rougher surfaces.

The ocean in near equilibrium with atmospheric methyl bromide

NASA Astrophysics Data System (ADS)

Hu, Lei; Yvon-Lewis, Shari; Liu, Yina; Bianchi, Thomas S.

2012-09-01

Saturation-anomaly measurements of methyl bromide (CH3Br) were made in the eastern Pacific (3/30-4/27, 2010) and the eastern Atlantic (10/25-11/26, 2010) to assess the oceanic saturation state as the phaseout of fumigation - non-Quarantine and Pre-Shipment (non-QPS) uses of CH3Br nears completion and atmospheric concentrations continue to decline. These cruises occurred 16 years after the Bromine Latitudinal Air-Sea Transect (BLAST) cruises, which were conducted in the same regions and first established a global oceanic net sink of -12.6 Gg yr-1 for atmospheric CH3Br in 1994. Results from this study suggest saturation anomalies of CH3Br in the surface ocean have become less negative than those observed 16 years ago as the atmospheric burden has declined over the past decade. The global net sea-to-air flux was estimated at 0 to 3 Gg yr-1 in 2010, suggesting that the ocean may become a net small source to atmospheric CH3Br. There are no significant differences between this study and previous studies for measured biological loss rate constants and calculated annual production rates, suggesting that annual production rates and biological degradation rate constants for CH3Br in the surface ocean have likely remained relatively constant over the past 16 years. When including the biological loss rate constants from this study and all previous studies, the mean global biological loss rate constant is constrained to 0.05 ± 0.01 d-1 (at a 95% confidence level). Combining chemical and eddy degradation rate constants, and using an updated gas transfer velocity, we estimate the CH3Br partial atmospheric lifetime with respect to oceanic loss to be 3.1 (2.3 to 5.0) years. Although the new partial atmospheric lifetime is about 1.3 years longer than the best prior estimate, it does not change the overall atmospheric lifetime of CH3Br, 0.8 (0.7-0.9) years.

A Zero-Dimensional Organic Seesaw-Shaped Tin Bromide with Highly Efficient Strongly Stokes-Shifted Deep-Red Emission

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhou, Chenkun; Lin, Haoran; Shi, Hongliang

The synthesis and characterization is reported of (C 9NH 20) 2SnBr 4, a novel organic metal halide hybrid with a zero-dimensional (0D) structure, in which individual seesaw-shaped tin (II) bromide anions (SnBr 4 2-) are co-crystallized with 1-butyl-1-methylpyrrolidinium cations (C 9NH 20 +). Upon photoexcitation, the bulk crystals exhibit a highly efficient broadband deep-red emission peaked at 695 nm, with a large Stokes shift of 332 nm and a high quantum efficiency of around 46 %. Furthermore, the unique photophysical properties of this hybrid material are attributed to two major factors: 1) the 0D structure allowing the bulk crystals tomore » exhibit the intrinsic properties of individual SnBr 4 2- species, and 2) the seesaw structure then enables a pronounced excited state structural deformation as confirmed by density functional theory (DFT) calculations.« less

pH-Dependent reversible crystal transformation of 1-carboxymethyl-1-methyl-pyrrolidinium bromides and their spectroscopic fingerprint

NASA Astrophysics Data System (ADS)

Tong, Ya-yan; Zhang, Heng; Chang, Liang-liang; Xuan, Xiao-peng

2018-03-01

In this work, two 1-carboxymethyl-1-methyl-pyrrolidinium bromides (N-methylpyrrolidine betaine hydrobromides) with the stoichiometry of betaine:hydrobromic acid as 1:1 and 2:1, denoted as CMPRHBr-I and CMPRHBr-II, respectively, were prepared and crystallographically determined. The large difference in these two structures is the type of hydrogen bonds, resulting in the different thermal stability. A strong Osbnd H ⋯ Br hydrogen bond was observed in CMPRHBr-I, whereas O ⋯ H ⋯ O hydrogen bond in CMPRHBr-II. Both these two crystals can mutually transform by changing the pH value of the aqueous solution. Vibrational spectroscopic studies shows that these two structures can be easily distinguished by the characteristic bands such as νCdbnd O stretching vibration and the D-type bands. Our studies indicate that it should be cautious of the structural change as this type of organic salts was purified and recrystallized.

Long-duration high-efficiency operation of a continuously pulsed copper laser utilizing copper bromide as a lasant

NASA Technical Reports Server (NTRS)

Chen, C. J.; Bhanji, A. M.; Russell, G. R.

1978-01-01

A copper laser utilizing copper bromide as a lasant and neon as the buffer gas has been operated at an average laser power of between 16 and 19.5 W for a period of 68 h. Lasing was attained at a pulsing rate of 16.7 kHz in a quartz discharge tube 2.5-cm in diameter with an electrode separation of 200 cm. The laser energy/pulse and peak power/pulse corresponding to an average power of 19.5 W are 1.2 mJ and 30 kW, respectively. The ratio of laser power at 510.6 and 578.2 nm varied from 3.9 to 1.1 corresponding to a total average laser power of 4 and 18 W, respectively. The highest wall plug and capacitor efficiency measured during 68 h of operation were 0.7 and 1.1%, respectively.

Copper(II)-catalyzed amidations of alkynyl bromides as a general synthesis of ynamides and Z-enamides. An intramolecular amidation for the synthesis of macrocyclic ynamides.

PubMed

Zhang, Xuejun; Zhang, Yanshi; Huang, Jian; Hsung, Richard P; Kurtz, Kimberly C M; Oppenheimer, Jossian; Petersen, Matthew E; Sagamanova, Irina K; Shen, Lichun; Tracey, Michael R

2006-05-26

A general and efficient method for the coupling of a wide range of amides with alkynyl bromides is described here. This novel amidation reaction involves a catalytic protocol using copper(II) sulfate-pentahydrate and 1,10-phenanthroline to direct the sp-C-N bond formation, leading to a structurally diverse array of ynamides including macrocyclic ynamides via an intramolecular amidation. Given the surging interest in ynamide chemistry, this atom economical synthesis of ynamides should invoke further attention from the synthetic organic community.

Synthesis and characterization of Ni(II) complex with 5,5,7,12,12,14-hexamethyl-1,4,8,11-tetraazacyclotetradeca-7,14-dienium bromide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yusoff, Latifah M.; Yusoff, Siti Fairus M.; Ismail, Wafiuddin

Nickel(II) complex have been synthesized by treating a 14-membered ring tetraaza macrocyclic compound, 5,5,7,12,12,14-hexamethyl-1,4,8,11-tetraazacyclotetradeca-7,14-dienium, bromide (Me{sub 6}N{sub 4}H{sub 4})Br{sub 2} with nickel acetate in metanol. The complex was characterized using elemental analysis, Fourier Transform Infrared (FTIR), Ultraviolet-Visible (UV-Vis), and single crystal diffraction (X-ray). The nickel atom coordinates through four nitrogen atoms in the ligand. Square planar geometry has been proposed for this complex.

Excitons in Potassium Bromide: A Study using Embedded Time-dependent Density Functional Theory and Equation-of-Motion Coupled Cluster Methods

DOE Office of Scientific and Technical Information (OSTI.GOV)

Govind, Niranjan; Sushko, Petr V.; Hess, Wayne P.

2009-03-05

We present a study of the electronic excitations in insulating materials using an embedded- cluster method. The excited states of the embedded cluster are studied systematically using time-dependent density functional theory (TDDFT) and high-level equation-of-motion coupled cluster (EOMCC) methods. In particular, we have used EOMCC models with singles and doubles (EOMCCSD) and two approaches which account for the e®ect of triply excited con¯gurations in non-iterative and iterative fashions. We present calculations of the lowest surface excitations of the well-studied potassium bromide (KBr) system and compare our results with experiment. The bulk-surface exciton shift is also calculated at the TDDFT levelmore » and compared with experiment.« less

Development and validation of a liquid chromatography-tandem mass spectrometry method for the determination of pyridostigmine bromide from guinea pig plasma.

PubMed

Needham, Shane R; Ye, Binying; Smith, J Richard; Korte, William D

2003-11-05

An HPLC/MS/MS method was validated for the low level analysis of pyridostigmine bromide (PB) from guinea pig plasma. An advantage of this strong-cation exchange HPLC/MS/MS method was the enhancement of the ESI-MS signal by providing good retention and good peak shape of PB with a mobile phase of 70% acetonitrile. In addition, the use of 70% acetonitrile in the mobile phase allowed the direct injection of the supernant from the protein precipitated extracted sample. The assay was linear from the range of 0.1 to 50 ng/ml using only 25 microl of sample. The precision and accuracy of the assay was better than 9.1 and 113%, respectively.

van der Waals three-body force shell model (VTSM) for the lattice dynamical studies of thallous bromide

NASA Astrophysics Data System (ADS)

Tiwari, Sarvesh K.; Pandey, L. K.; Shukla, Lal Ji; Upadhyaya, K. S.

2009-12-01

The van der Waals three-body force shell model (VTSM) has been developed by modifying the three-body force shell model (TSM) for the lattice dynamics of ionic crystals with cesium chloride (CsCl) structure. This new model incorporates van der Waals interactions along with long-range Coulomb interactions, three-body interactions and short-range second neighbour interactions in the framework of a rigid shell model (RSM). In the present paper, VTSM has been used to study the lattice dynamics of thallous bromide (TlBr), from which adequacy of VTSM has been established. A comparative study of the dynamical behaviour of TlBr has also been done between the present model and TSM, the model over which modification has been made to obtain the present model VTSM. Good agreement has been observed between the theoretical and experimental results, which give confidence that it is an appropriate model for the complete description of ionic crystals with CsCl structure.

XRD, TEM, and thermal analysis of Arizona Ca-montmorillonites modified with didodecyldimethylammonium bromide.

PubMed

Sun, Zhiming; Park, Yuri; Zheng, Shuilin; Ayoko, Godwin A; Frost, Ray L

2013-10-15

An Arizona SAz-2 calcium montmorillonite was modified by a typical dialkyl cationic surfactant (didodecyldimethylammonium bromide, abbreviated to DDDMA) through direct ion exchange. The obtained organoclays were characterized by X-ray diffraction (XRD), high-resolution transmission electron microscopy (HR-TEM), high-resolution thermogravimetric analysis (HR-TG), and infrared emission spectroscopy (IES). The intercalation of surfactants greatly increased the basal spacing of the interlayers and the conformation arrangement of the loaded surfactant were assessed based on the XRD and TEM measurements. This work shows that the dialkyl surfactant can be directly intercalated into the montmorillonite without first undergoing Na(+) exchange. Moreover, the thermal stability of organoclays and the different arrangements of the surfactant molecules intercalated in the SAz-2 Ca-montmorillonite were determined by a combination of TG and IES techniques. The detailed conformational ordering of different intercalated surfactants under different conditions was also studied. The surfactant molecule DDDMA has proved to be thermally stable even at 400°C which indicates that the prepared organoclay is stable to significantly high temperatures. This study offers new insights into the structure and thermal stabilities of SAz-2 Ca-montmorillonite modified with DDDMA. The experimental results also confirm the potential applications of organic SAz-2 Ca-montmorillonites as adsorbents and polymer-clay nanocomposites. Copyright © 2013 Elsevier Inc. All rights reserved.

Pinaverium Bromide: Development and Validation of Spectrophotometric Methods for Assay and Dissolution Studies.

PubMed

Martins, Danielly da Fonte Carvalho; Florindo, Lorena Coimbra; Machado, Anna Karolina Mouzer da Silva; Todeschini, Vítor; Sangoi, Maximiliano da Silva

2017-11-01

This study presents the development and validation of UV spectrophotometric methods for the determination of pinaverium bromide (PB) in tablet assay and dissolution studies. The methods were satisfactorily validated according to International Conference on Harmonization guidelines. The response was linear (r2 > 0.99) in the concentration ranges of 2-14 μg/mL at 213 nm and 10-70 μg/mL at 243 nm. The LOD and LOQ were 0.39 and 1.31 μg/mL, respectively, at 213 nm. For the 243 nm method, the LOD and LOQ were 2.93 and 9.77 μg/mL, respectively. Precision was evaluated by RSD, and the obtained results were lower than 2%. Adequate accuracy was also obtained. The methods proved to be robust using a full factorial design evaluation. For PB dissolution studies, the best conditions were achieved using a United States Pharmacopeia Dissolution Apparatus 2 (paddle) at 50 rpm and with 900 mL 0.1 M hydrochloric acid as the dissolution medium, presenting satisfactory results during the validation tests. In addition, the kinetic parameters of drug release were investigated using model-dependent methods, and the dissolution profiles were best described by the first-order model. Therefore, the proposed methods were successfully applied for the assay and dissolution analysis of PB in commercial tablets.

Potential impurities in drug substances: Compound-specific toxicology limits for 20 synthetic reagents and by-products, and a class-specific toxicology limit for alkyl bromides.

PubMed

Bercu, J P; Galloway, S M; Parris, P; Teasdale, A; Masuda-Herrera, M; Dobo, K; Heard, P; Kenyon, M; Nicolette, J; Vock, E; Ku, W; Harvey, J; White, A; Glowienke, S; Martin, E A; Custer, L; Jolly, R A; Thybaud, V

2018-04-01

This paper provides compound-specific toxicology limits for 20 widely used synthetic reagents and common by-products that are potential impurities in drug substances. In addition, a 15 μg/day class-specific limit was developed for monofunctional alkyl bromides, aligning this with the class-specific limit previously defined for monofunctional alkyl chlorides. Both the compound- and class-specific toxicology limits assume a lifetime chronic exposure for the general population (including sensitive subpopulations) by all routes of exposure for pharmaceuticals. Inhalation-specific toxicology limits were also derived for acrolein, formaldehyde, and methyl bromide because of their localized toxicity via that route. Mode of action was an important consideration for a compound-specific toxicology limit. Acceptable intake (AI) calculations for certain mutagenic carcinogens assumed a linear dose-response for tumor induction, and permissible daily exposure (PDE) determination assumed a non-linear dose-response. Several compounds evaluated have been previously incorrectly assumed to be mutagenic, or to be mutagenic carcinogens, but the evidence reported here for such compounds indicates a lack of mutagenicity, and a non-mutagenic mode of action for tumor induction. For non-mutagens with insufficient data to develop a toxicology limit, the ICH Q3A qualification thresholds are recommended. The compound- and class-specific toxicology limits described here may be adjusted for an individual drug substance based on treatment duration, dosing schedule, severity of the disease and therapeutic indication. Copyright © 2018. Published by Elsevier Inc.

Biofilm formation by Staphylococcus aureus and Salmonella spp. under mono and dual-species conditions and their sensitivity to cetrimonium bromide, peracetic acid and sodium hypochlorite.

PubMed

Iñiguez-Moreno, Maricarmen; Gutiérrez-Lomelí, Melesio; Guerrero-Medina, Pedro Javier; Avila-Novoa, María Guadalupe

The aim of this study was evaluated the biofilm formation by Staphylococcus aureus 4E and Salmonella spp. under mono and dual-species biofilms, onto stainless steel 316 (SS) and polypropylene B (PP), and their sensitivity to cetrimonium bromide, peracetic acid and sodium hypochlorite. The biofilms were developed by immersion of the surfaces in TSB by 10 d at 37°C. The results showed that in monospecies biofilms the type of surface not affected the cellular density (p>0.05). However, in dual-species biofilms on PP the adhesion of Salmonella spp. was favored, 7.61±0.13Log 10 CFU/cm 2 , compared with monospecies biofilms onto the same surface, 5.91±0.44Log 10 CFU/cm 2 (p<0.05). The mono and dual-species biofilms were subjected to disinfection treatments; and the most effective disinfectant was peracetic acid (3500ppm), reducing by more than 5Log 10 CFU/cm 2 , while the least effective was cetrimonium bromide. In addition, S. aureus 4E and Salmonella spp. were more resistant to the disinfectants in mono than in dual-species biofilms (p<0.05). Therefore, the interspecies interactions between S. aureus 4E and Salmonella spp. had a negative effect on the antimicrobial resistance of each microorganism, compared with the monospecies biofilms. Copyright © 2017 Sociedade Brasileira de Microbiologia. Published by Elsevier Editora Ltda. All rights reserved.

Allyl triphenyl phosphonium bromide based DES-functionalized carbon nanotubes for the removal of mercury from water.

PubMed

AlOmar, Mohamed Khalid; Alsaadi, Mohammed Abdulhakim; Hayyan, Maan; Akib, Shatirah; Ibrahim, Muhammad; Hashim, Mohd Ali

2017-01-01

Recently, deep eutectic solvents (DESs) have shown their new and interesting ability for chemistry through their involvement in variety of applications. This study introduces carbon nanotubes (CNTs) functionalized with DES as a novel adsorbent for Hg 2+ from water. Allyl triphenyl phosphonium bromide (ATPB) was combined with glycerol as the hydrogen bond donor (HBD) to form DES, which can act as a novel CNTs functionalization agent. The novel adsorbent was characterized using Raman, FTIR, XRD, FESEM, EDX, BET surface area, TGA, TEM and Zeta potential. Response surface methodology was used to optimize the removal conditions for Hg 2+ . The optimum removal conditions were found to be pH 5.5, contact time 28 min, and an adsorbent dosage of 5 mg. Freundlich isotherm model described the adsorption isotherm of the novel adsorbent, and the maximum adsorption capacity obtained from the experimental data was 186.97 mg g -1 . Pseudo-second order kinetics describes the adsorption rate order. Copyright © 2016 Elsevier Ltd. All rights reserved.

Studies of interaction of emodin and DNA in the presence of ethidium bromide by spectroscopic method

NASA Astrophysics Data System (ADS)

Bi, Shuyun; Zhang, Hanqi; Qiao, Chunyu; Sun, Ying; Liu, Chunming

2008-01-01

Emodin interacting with deoxyribonucleic acid (DNA) has been studied by different spectroscopic techniques, such as fluorescence, ultraviolet and visible (UV-vis), and fourier transform infared (FT-IR) spectroscopies, using ethidium bromide (EB) as a fluorescence probe of DNA. The decrease in the fluorescence of DNA-EB system on addition of emodin shows that the fluorescence quenching of DNA-EB complex by emodin occurs. The binding constants of emodin with DNA in the presence of EB are 6.02 × 10 4, 9.20 × 10 4 and 1.17 × 10 5 L mol -1 at 20, 35 and 50 °C, respectively. FT-IR spectrum further suggests that both the phosphate groups and the bases of DNA react with emodin. The reaction of DNA with emodin in the presence of EB is affected by ionic strength and temperature. The values of melting temperature ( Tm) of DNA-EB complex and emodin-DNA-EB complexes were determined, respectively. From the experiment evidences, the major binding mode of emodin with DNA should be the groove binding.

Advances in crystal growth, device fabrication and characterization of thallium bromide detectors for room temperature applications

NASA Astrophysics Data System (ADS)

Datta, Amlan; Moed, Demi; Becla, Piotr; Overholt, Matthew; Motakef, Shariar

2016-10-01

Thallium bromide (TlBr) is a promising room-temperature radiation detector candidate with excellent charge transport properties. However, several critical issues need to be addressed before deployment of this material for long-term field applications can be realized. In this paper, progress made towards solving some of these challenges is discussed. The most significant factors for achieving long-term performance stability for TlBr devices include residual stress as generated during crystal growth and fabrication processes, surface conditions, and the choice of contact metal. Modifications to the commonly used traveling molten zone growth technique for TlBr crystals can significantly minimize the stresses generated by large temperature gradients near the melt-solid interface of the growing crystal. Plasma processing techniques were introduced for the first time to modify the Br-etched TlBr surfaces, which resulted in improvements to the surface conditions, and consequently the spectroscopic response of the detectors. Palladium electrodes resulted a 20-fold improvement in the room-temperature device lifetime when compared to its Br-etched Pt counterpart.

Comparison of gadopentetic acid (Gd-DTPA) and bromide in a dual-tracer field experiment

NASA Astrophysics Data System (ADS)

Dulski, Peter; Möller, Peter; Pekdeger, Asaf

2011-06-01

At a test site consisting of a storage pond and connected artificial aquifer, the long-time behaviour of gadopentetic acid (Gd-DTPA) was compared with the classic tracer bromide (Br-) in a 70-day dual-tracer experiment. The mixed tracer solution was injected into the oligotrophic pond, which is separated from the aquifer by an infiltration bank. The water drained from the aquifer was returned to the pond together with additional fresh groundwater, causing reduced concentrations of Gd-DTPA and Br- in the system. Transmetallation of Gd-DTPA by rare earth elements and yttrium was negligible but Cu2+ and Ni2+ might have played a role. Adsorption and/or biodegradation of Gd-DTPA were negligible. The decline of Gd-DTPA/Br ratios by 18% in the pond over 68 days was caused by reversible sorption of Br- in the aquifer, which caused variation of Br- background. Thus, Br- behaves less conservatively than Gd-DTPA in the aquifer. Comparison of both proves the suitability of Gd-chelates as tracers in hydrological studies. The advantage of Gd-DTPA as a tracer is that natural Gd3+ in water can continuously be monitored by analysing the suite of naturally occurring rare-earth elements. Thus, stable organic Gd-chelates are determinable with high precision at very low concentrations.

Oxidative precipitation of ruthenium oxide for supercapacitors: Enhanced capacitive performances by adding cetyltrimethylammonium bromide

NASA Astrophysics Data System (ADS)

Chen, I.-Li; Wei, Yu-Chen; Chen, Tsan-Yao; Hu, Chi-Chang; Lin, Tsang-Lang

2014-12-01

Thermally stable and porous RuO2·xH2O with superior rate-retention capability is prepared by the H2O2-oxidative precipitation method modified with the cetyltrimethylammonium bromide (CTAB) template. The specific capacitance and rate-retention of RuO2·xH2O are considerably enhanced by the CTAB modification and annealing at 200 °C because of extremely localized crystallization and pore opening of slightly sintered RuO2·xH2O nanoparticles trapped with CTAB. This unique structure, confirmed by the X-ray absorption spectroscopic (XAS), Raman spectroscopic, and transmission electron microscopic (TEM) analyses, favors the utilization of RuO2·xH2O nanocrystals and increases the electrolyte accessibility in comparing with RuO2·xH2O without CTAB modification. The preferential orientation growth along the {101} facet of RuO2 nanocrystals in some local regions is acquired by the CTAB modification and annealing in air at temperatures ≥350 °C. Such preferential orientation growth of RuO2 crystallites is attributable to the oxidation of trapped surfactants during the thermal annealing process, which adsorb on the high surface energy planes of RuO2.

Enhanced removal of bisphenol-AF by activated carbon-alginate beads with cetyltrimethyl ammonium bromide.

PubMed

Tang, Zheng; Peng, Sha; Hu, Shuya; Hong, Song

2017-06-01

Adsorption removal of bisphenol-AF (BPAF) from aqueous solutions by synthesized activated carbon-alginate beads (AC-AB) with cetyltrimethyl ammonium bromide (CTAB) has been studied using two ways. The traditional method (two-step) first synthesized CTAB-modified AC-AB (AC-AB-CTAB), then used it to remove BPAF by adsorption. And one-step method dispersed AC-AB and CTAB in wastewater, followed by the removal of BPAF accompanied with the synthesis of AC-AB-CTAB. The one-step method showed a better performance than the two-step method, achieving a maximum removal of BPAF with 284.6mg/g. Kinetic studies and adsorption isotherms indicated that adsorption process of BPAF on AC-AB by the one-step method could be expressed by a pseudo-second-order model and a Dubinin-Ashtakhov (D-A) isotherm, respectively. The effects of pH, ionic strength, and inorganic ions on BPAF adsorption were also investigated. Furthermore, hydrophobic interactions, hydrogen bonds, and π-π electron donor-acceptor (EDA) interactions were discussed to explain the enhanced adsorption behavior of BPAF on AC-AB with CTAB. The findings verified the effectiveness of AC-AB for the removal of BPAF from wastewater and its high stability within five regeneration cycles. Copyright © 2017 Elsevier Inc. All rights reserved.

Efficient capture of SO2 by a binary mixture of caprolactam tetrabutyl ammonium bromide ionic liquid and water.

PubMed

Duan, Erhong; Guo, Bin; Zhang, Miaomiao; Guan, Yanan; Sun, Hua; Han, Jing

2011-10-30

The solubility of SO(2) in a binary mixture of water and caprolactam tetrabutyl ammonium bromide ionic liquid (CPL-TBAB IL) was investigated. Though the ionic liquid and water were fully miscible, a phase separation occurred when SO(2) was introduced into the mixture. The SO(2) concentrated in the lower layer, and it could be released by heating the solution under reduced pressure (382.2K, 10.1 kPa). After desorption, the mixture could be reused to absorb SO(2). It was found that SO(2) acts as a switch to cause the water and CPL-TBAB IL to phase separate, and the mechanics of this phase separation process was studied by gas chromatography-mass spectrometry, fourier transform-infrared spectroscopy and Karl-Fisher titration. The absorption and desorption of SO(2) in the CPL-TBAB/water mixtures were reversible. Copyright © 2011 Elsevier B.V. All rights reserved.

Factors affecting the stability and performance of ipratropium bromide; fenoterol hydrobromide pressurized-metered dose inhalers.

PubMed

Ninbovorl, Jenjira; Sawatdee, Somchai; Srichana, Teerapol

2013-12-01

The aim of the study was to investigate the factors affecting the stability and performance of ipratropium bromide and fenoterol hydrobromide in a pressurized-metered dose inhaler (pMDI). A factorial design was applied to investigate the effects of three parameters (propellant, water, and ethanol) on the performance of 27 designed formulations of a solution-based pMDI. The formulations that contained a hydrofluoroalkane (HFA) propellant lower than 72% v/v and an ethanol concentration higher than 27% v/v remained as clear solutions. Nine formulations that contained the HFA propellant higher than 74% v/v precipitated. The results indicated that it was not only the HFA propellant content of the formulations that was related to the formulation instability but also ethanol content. Only six formulations from the 18 formulations, that did not precipitate, produced drug contents that were within the acceptable range (80-120%). These six formulations generated aerosols with mass median aerodynamic diameters (MMAD) of approximately 2 μm with a fine particle fraction (FPF; particle size, <6.4 μm) between 45% and 52%. The MMAD and FPF did not change significantly after 6 months of storage (P > 0.05).

Synthesis of tetraaza bromide macrocyclic and studies of its effect on poly(methyl methacrylate) grafted natural rubber (MG49) - lithium tertrafluoroborate (LiBF{sub 4}) films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mariam, Siti Nor; Yamin, Bohari M.; Ahmad, Azizan

2013-11-27

Good Poly(Methyl Methacrylate) Grafted natural Rubber (MG49) films with homogeneous and smooth surface were obtained in the presence of Lithium Tertrafluoroborate (LiBF{sub 4}) and 5,5,7,12,12,14-hexamethyl-1,4,8,11-tetraazacyclotetradeca-7,14-dienium bromide, (Me{sub 6}N{sub 4}H{sub 4})Br{sub 2} as dopants. The conductivity was found to be 3.63×10{sup −6} S/cm an increase by seven fold compare to the undoped MG49.

Ex situ generation of stoichiometric HCN and its application in the Pd-catalysed cyanation of aryl bromides: evidence for a transmetallation step between two oxidative addition Pd-complexes.

PubMed

Kristensen, Steffan K; Eikeland, Espen Z; Taarning, Esben; Lindhardt, Anders T; Skrydstrup, Troels

2017-12-01

A protocol for the Pd-catalysed cyanation of aryl bromides using near stoichiometric and gaseous hydrogen cyanide is reported for the first time. A two-chamber reactor was adopted for the safe liberation of ex situ generated HCN in a closed environment, which proved highly efficient in the Ni-catalysed hydrocyanation as the test reaction. Subsequently, this setup was exploited for converting a range of aryl and heteroaryl bromides (28 examples) directly into the corresponding benzonitriles in high yields, without the need for cyanide salts. Cyanation was achieved employing the Pd(0) precatalyst, P( t Bu) 3 -Pd-G3 and a weak base, potassium acetate, in a dioxane-water solvent mixture. The methodology was also suitable for the synthesis of 13 C-labelled benzonitriles with ex situ generated 13 C-hydrogen cyanide. Stoichiometric studies with the metal complexes were undertaken to delineate the mechanism for this catalytic transformation. Treatment of Pd(P( t Bu) 3 ) 2 with H 13 CN in THF provided two Pd-hydride complexes, (P( t Bu) 3 ) 2 Pd(H)( 13 CN), and [(P( t Bu) 3 )Pd(H)] 2 Pd( 13 CN) 4 , both of which were isolated and characterised by NMR spectroscopy and X-ray crystal structure analysis. When the same reaction was performed in a THF : water mixture in the presence of KOAc, only (P( t Bu) 3 ) 2 Pd(H)( 13 CN) was formed. Subjection of this cyano hydride metal complex with the oxidative addition complex (P( t Bu) 3 )Pd(Ph)(Br) in a 1 : 1 ratio in THF led to a transmetallation step with the formation of (P( t Bu) 3 ) 2 Pd(H)(Br) and 13 C-benzonitrile from a reductive elimination step. These experiments suggest the possibility of a catalytic cycle involving initially the formation of two Pd(ii)-species from the oxidative addition of L n Pd(0) into HCN and an aryl bromide followed by a transmetallation step to L n Pd(Ar)(CN) and L n Pd(H)(Br), which both reductively eliminate, the latter in the presence of KOAc, to generate the benzonitrile and L n Pd(0).

Extraction and Chromatographic Determination of Shikimic Acid in Chinese Conifer Needles with 1-Benzyl-3-methylimidazolium Bromide Ionic Liquid Aqueous Solutions

PubMed Central

Chen, Fengli; Hou, Kexin; Li, Shuangyang; Zu, Yuangang; Yang, Lei

2014-01-01

An ionic liquids-based ultrasound-assisted extraction (ILUAE) method was successfully developed for extracting shikimic acid from conifer needles. Eleven 1-alkyl-3-methylimidazolium ionic liquids with different cations and anions were investigated and 1-benzyl-3-methylimidazolium bromide solution was selected as the solvent. The conditions for ILUAE, including the ionic liquid concentration, ultrasound power, ultrasound time, and liquid-solid ratio, were optimized. The proposed method had good recovery (99.37%–100.11%) and reproducibility (RSD, n = 6; 3.6%). ILUAE was an efficient, rapid, and simple sample preparation technique that showed high reproducibility. Based on the results, a number of plant species, namely, Picea koraiensis, Picea meyeri, Pinus elliottii, and Pinus banksiana, were identified as among the best resources of shikimic acid. PMID:24782942

(Carbonato-κ2 O,O′)bis­(di-2-pyridyl­amine-κ2 N,N′)cobalt(III) bromide

PubMed Central

Czapik, Agnieszka; Papadopoulos, Christos; Lalia-Kantouri, Maria; Gdaniec, Maria

2011-01-01

In the title compound, [Co(CO3)(C10H9N3)2]Br, a distorted octa­hedral coordination of the CoIII atom is completed by four N atoms of the two chelating di-2-pyridyl­amine ligands and two O atoms of the chelating carbonate anion. The di-2-pyridyl­amine ligands are nonplanar and the dihedral angles between the 2-pyridyl groups are 29.11 (9) and 37.15 (12)°. The coordination cation, which has approximate C 2 symmetry, is connected to the bromide ion via an N—H⋯Br− hydrogen bond. The ionic pair thus formed is further assembled into a dimer via N—H⋯O inter­actions about an inversion centre. A set of weaker C—H⋯O and C—H⋯Br− inter­actions connect the dimers into a three-dimensional network. PMID:21753946

Effects of Ultrasonic Vibration on Heat Transfer Characteristics of Lithium Bromide Aqueous Solution under the Reduced Pressure

NASA Astrophysics Data System (ADS)

Yamashiro, Hikaru; Nakashima, Ryou

The effects of ultrasonic vibration on heat transfer characteristics of lithium bromide aqueous solution under the reduced pressures are studied experimentally. Pool boiling curves on horizontal smooth tube are obtained using distilled water and 50 % LiBr aqueous solution as test liquids. The system pressure p is varied from 12 to 101 kPa and the liquid subcooling ΔTsub ranges from 0 to 70 K. The frequency of ultrasonic vibration vi s set at 24 and 44 kHz, and the power input to the vibrator P is varied from 0 to 35 W. The wall superheat at the boiling incipience is found to decrease with increasing P, and the nucleate boiling curve shifts toward the lower wall temperature region. However, the effect of P is not found to be very significant in the high heat flux region, especially in the case of small liquid subcooling. Ultrasonic vibration is also found to improve the nucleate boiling heat transfer coefficient by up to a maximum of 3.5 times and to prevent crystallization of the solution and precipitation of additives.

Preparation and characterization of poly(lactic acid) nanoparticles for sustained release of pyridostigmine bromide.

PubMed

Tan, Q Y; Xu, M L; Wu, J Y; Yin, H F; Zhang, J Q

2012-04-01

A novel pyridostigmine bromide poly (lactic acid) nanoparticles (PBPNPs) was prepared to obtain sustained release characteristics of PB. A central composite design approach was employed for process optimization. The in vitro release studies were carried out by dialysis method and conducted using four different dissolution media. Similar factor method was investigated for dissolution profile comparison. Multiple linear regression analysis for process optimization revealed that the optimal PBPNPs were obtained where the values of the amount of PB (X1, mg), PLA concentration (X2, % w:v), and PVA concentration (X3, % w:v) were 49.20 mg, 3.31% and 3.41%, respectively. The average particle size and zeta potential of PBPNPs with the optimized formulation were 722.9 +/- 4.3 nm, and -25.12 +/- 1.2 mV, respectively. PBPNPs provided an initial burst of drug release followed by a very slow release over an extended period of time (72 h). Compared with free PB, PBPNPs had a significantly lower release rate of PB in vitro. The in vitro release profile of the PBPNPs could be described by Weibull models, regardless of type of dissolution medium. Statistical significance of similarity between every two dissolution profiles of PBPNPs in different dissolution media was found, and the difference between the curves of PBPNPs and pure PB was statistically significant.

Modification of carbon nanotube's dispersion using cetyltrimethyl ammonium bromide (CTAB) as cancer drug delivery

NASA Astrophysics Data System (ADS)

Wulan, Praswati PDK.; Wulandari, Hanifia; Ulwan, Sekar H.; Purwanto, Widodo W.; Mulia, Kamarza

2018-02-01

Cancer is a disease that causes many deaths globally. Cancer treatments have side effects that can danger the human body. Carbon nanotube (CNT) becomes drug (anti-cancer) delivery towards cancer cells that have been targeted. Yet, CNT tends to aggregate. It could be overcome by functionalization (modification) of CNT using Cetyltrimethyl Ammonium Bromide (CTAB). The variations we use were CNT-CTAB with a dose of CNT 100 mg and CTAB varied between 80, 90, 100, 110, and 120 mg. There were several stages of CNT modification process: dispersion, filtration, washing, and drying. The optimum condition obtained was on CNT-110 mg CTAB because it could be dispersed up to 70 hours better than pure CNT, Zeta Potential (ZP) ≥16 mV, and absorbance Uv-vis 1.05. Both the ZP value and the absorbance of Uv-vis showed the CNT dispersion modified to be better than the pure CNT. Furthermore, SEM-EDX did not produce structural damage to CNT modified surfaces, the percentage of the mass of Oxygen (O) elements as characteristic of increased hydrophilic properties, and Ni elements as toxic impurities become reduced. FTIR spectrum results showed the highest intensity occurred at CTAB CNT-110mg at 1221 m-1. This strong C-N vibration interaction suggests that CNTs CNT modification become readily dispersed in water.

Increasing Fe0-mediated HMX destruction in highly contaminated soil with didecyldimethylammonium bromide surfactant.

PubMed

Park, Jeong; Comfort, Steve D; Shea, Patrick J; Kim, Jong Sung

2005-12-15

Mixtures of energetic compounds pose a remediation problem for munitions-contaminated soil. Although treatment with zerovalent iron (Fe0) can be effective, RDX and TNT are more readily destroyed than HMX. Adding didecyldimethylammonium bromide (didecyl) at 2% w/v with 3% (w/v) Fe0 to a 20% slurry of Los Alamos National Laboratory soil containing solid-phase HMX (45 000 mg/kg) resulted in >80% destruction within 6 days. Because the HMX concentration did not increase in solution and the didecyl equilibrium concentration was well below the critical micelle concentration, we conclude thatthe solution primarily contained didecyl monomers. The adsorption isotherm for didecyl on iron is consistent with electrostatic adsorption of monomers and some hydrophobic partitioning at low equilibrium concentrations. Fe0 pretreated with didecyl was superior to Fe0 alone or mixed with didecyl in removing HMX from solution, but it was less effective than Fe0 + didecyl when solid-phase HMX was present. Reseeding HMX to mimic dissolution indicated an initial high reactivity of didecyl-pretreated Fe0, but the reaction slowed with each HMX addition. In contrast, reaction rates were lower but reactivity was maintained when Fe0 and didecyl were added together and didecyl was included in fresh HMX solutions. Destruction of solid-phase HMX requires low didecyl concentrations in solution so that hydrophobic patches are maintained on the iron surface.

1-(3-aminopropyl)-3-butylimidazolium bromide for carboxyl group derivatization: potential applications in high sensitivity peptide identification by mass spectrometry.

PubMed

Qiao, Xiaoqiang; Zhou, Yuan; Hou, Chunyan; Zhang, Xiaodan; Yang, Kaiguang; Zhang, Lihua; Zhang, Yukui

2013-03-01

The cationic reagent 1-(3-aminopropyl)-3-butylimidazolium bromide (BAPI) was exploited for the derivatization of carboxyl groups on peptides. Nearly 100% derivatization efficiency was achieved with the synthetic peptide RVYVHPI (RI-7). Furthermore, the peptide derivative was stable in a 0.1% TFA/water solution or a 0.1% (v/v) TFA/acetonitrile/water solution for at least one week. The effect of BAPI derivatization on the ionization of the peptide RI-7 was further investigated, and the detection sensitivity was improved >42-fold via matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS), thus outperforming the commercial piperazine derivatization approach. Moreover, the charge states of the peptide were largely increased via BAPI derivatization by electrospray ionization (ESI) MS. The results indicate the potential merits of BAPI derivatization for high sensitivity peptide analysis by MS.

Determination of nitrite, nitrate, bromide, and iodide in seawater by ion chromatography with UV detection using dilauryldimethylammonium-coated monolithic ODS columns and sodium chloride as an eluent.

PubMed

Ito, Kazuaki; Nomura, Ryosuke; Fujii, Takuya; Tanaka, Masahito; Tsumura, Tomoaki; Shibata, Hiroyuki; Hirokawa, Takeshi

2012-11-01

A method was developed for determination of inorganic anions, including nitrite (NO(2)(-)), nitrate (NO(3)(-)), bromide (Br(-)), and iodide (I(-)), in seawater by ion chromatography (IC). The IC system used two dilauryldimethylammonium bromide (DDAB)-coated monolithic ODS columns (50 × 4.6 mm i.d. and 100 × 4.6 mm i.d.) connected in series for separation of the ions. Aqueous NaCl (0.5 mol/L; flow rate, 3 mL/min) containing 5 mmol/L phosphate buffer (pH 5) was used as the eluent, and detection was with a UV detector at 225 nm. The monolithic ODS columns were coated and equilibrated with a 1-mmol/L DDAB solution (in H(2)O/methanol, 90:10 v/v). The hydrophilic ions (NO(2)(-), NO(3)(-), and Br(-)) were separated within 3 min and the retention time of I(-) was 16 min. No interferences from matrix ions, such as chloride and sulfate ions, were observed in 35 ‰ artificial seawater. The detection limits were 0.6 μg/L for NO(2)(-), 1.1 μg/L for NO(3)(-), 70 μg/L for Br(-), and 1.6 μg/L for I(-) with a 200-μL sample injection. The performance of the coated columns was maintained without addition of DDAB in the eluent. The IC system was successfully applied to real seawater samples with recovery rates of 94-108 % for all ions.

Effects of Fructose and Temperature on the Micellization of a Cationic Gemini Surfactant, Pentanediyl-1,5-bis(dimethylcetylammonium) Bromide in Aqueous Solutions

NASA Astrophysics Data System (ADS)

Alam, Md. Sayem; Mohammed Siddiq, A.; Mandal, Asit Baran

2017-12-01

By the conductivity measurements the effects of fructose and temperature (293-308 K) on the micellization of a cationic gemini surfactant (GS), pentanediyl-1,5-bis(dimethylcetylammonium) bromide in aqueous solutions have been investigated. The critical micelle concentration (CMC) of GS was measured at the different temperatures and fructose concentrations. An increasing trend of the CMC values is with addition of fructose. With increasing temperature, the CMC values are in a similar increasing trend. The CMC of GS by dye solubilization method at room temperature have been determined. The standard Gibbs energy, enthalpy and entropy of GS micellization have been evaluated. From these thermodynamic parameters, it was found that in presence of fructose, the stability of the GS aqueous solutions decreases.

The microwave assisted synthesis of 1-alkyl-3-methylimidazolium bromide as potential corrosion inhibitor toward carbon steel in 1 M HCl solution saturated with carbon dioxide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pasasa, Norman Vincent A., E-mail: npasasa@gmail.com; Bundjali, Bunbun; Wahyuningrum, Deana

Injection of corrosion inhibitor into the fluid current of oil and gas pipelines is an effective way to mitigate corrosion rate on the inner-surface parts of pipelines, especially carbon steel pipelines. In this research, two alkylimidazolium ionic liquids, 1-decyl-3-methylimidazolium bromide (IL1) and 1-dodecyl-3-methylimidazolium bromide (IL2) have been synthesized and studied as a potential corrosion inhibitor towards carbon steel in 1 M HCl solution saturated with carbon dioxide. IL1 and IL2 were synthesized using microwave assisted organic synthesis (MAOS) method. Mass Spectrometry analysis of IL1 and IL2 showed molecular mass [M-H+] peak at 223.2166 and 251.2484, respectively. The FTIR,{sup 1}H-NMR andmore » {sup 13}C-NMR spectra confirmed that IL1 and IL2 were successfully synthesized. Corrosion inhibition activity of IL1 and IL2 were determined using weight loss method. The results showed that IL1 and IL2 have the potential as good corrosion inhibitors with corrosion inhibition efficiency of IL1 and IL2 are 96.00% at 100 ppm (343 K) and 95.60% at 50 ppm (343 K), respectively. The increase in the concentration of IL1 and IL2 tends to improve their corrosion inhibition activities. Analysis of the data obtained from the weight loss method shows that the adsorption of IL1 and IL2 on carbon steel is classified into chemisorption which obeys Langmuir’s adsorption isotherm.« less

Determination of emodin by hexadecyl trimethyl ammonium bromide sensitized fluorescence quenching method of the derivatives of calix[4]arene

NASA Astrophysics Data System (ADS)

Ma, Lina; Zhu, Xiashi

2012-09-01

The fluorescence quenching effect of emodin (EMO) on the derivatives of p-tert-butyl-calix[4]arene with o-phenanthroline (TBCP) in 1.0% hexadecyl trimethyl ammonium bromide (CTAB) medium was investigated. The fluorescence of TBCP was quenched by EMO due to the formation of the weak fluorescent inclusion complex (EOM-TBCP), and the fluorescence quenching (ΔF = FTBCP-FEMO-TBCP) was sensitized in CTAB. Under the optimal conditions, the linear range of calibration curve for the determination of EMO was 1.17-23.40 μg/mL. The detection limit estimated and RSD was 0.34 μg/mL, 3.63% (n = 3, c = 4.74 μg/mL). The quantum yield Yu of TBCP was approximately 2.0 times higher in the presence of CTAB than that in the absence of CTAB. The method has been applied for the determination of EMO in samples with satisfactory results.

Effect of chronic pyridostigmine bromide treatment on cardiovascular and behavioral parameters in mice.

PubMed

Bernatova, Iveta; Dubovicky, Michal; Price, William A; Grubbs, Robert D; Lucot, James B; Morris, Mariana

2003-03-01

Experiments were performed to determine the effect of chronic low-dose pyridostigmine bromide (PB) treatment on blood acetylcholinesterase (AChE), cardiovascular (CV) function, and behavior in C57BL/6J male mice. Chronic carotid arterial catheters were used for long-term CV measurements and for collection of blood samples. Separate groups of mice were used for behavioral open field tests. PB was administered subcutaneously using osmotic minipumps at 1 and 3 mg/kg/day for 7 days. Blood pressure and heart rate (HR) were measured continuously for 24 h before treatment and on Days 3 and 7 after minipump insertion. Blood samples were collected on the same days. Mean arterial pressure (MAP) of the control group was 108+/-2 and 104+/-2 mm Hg during the dark and light periods, respectively. HR was 510+/-18 and 493+/-19 beats/min during the dark and light periods, respectively. PB treatment had no effect on MAP or HR in either dark or light period. Basal AChE activity was 0.42+/-0.1 micromol/min/ml, with no changes observed with PB at 1 mg/kg/day. The higher PB dose (3 mg/kg/day) decreased blood AChE activity by 85% on Day 7. Despite the reduction in blood AChE activity, there were no alterations in open field behaviors (locomotor activity, rearing, distance traveled, rest time, number of entries, and pokes). In conclusion, chronic low-dose PB exposure decreased blood AChE activity but had no effect on CV function or behavior in mice.

Use of cetyltrimethylammonium bromide as a simple probe for rapid determination of emodin by resonance light scattering technique

NASA Astrophysics Data System (ADS)

Xiang, Haiyan; Luo, Qizhi; Dai, Kaijin; Duan, Wenjun; Fan, Yinzhou; Xie, Yang

2012-10-01

A new resonance light scattering (RLS) method for emodin determination with cationic surfactant cetyltrimethylammonium bromide (CTAB) as probe has been developed. In Britton-Robinson buffer (pH 6.5) medium, emodin reacted with cationic surfactant CTAB and formed the emodin-CTAB complex. The complex aggregated together through hydrophobic forces and causing great enhancement of RLS signals with the maximum peak located at about 350 nm. The enhanced RLS intensities were found to be proportional to the concentration of emodin in the range of 0.54-9.72 μg ml-1 with the detection limit (3σ) of 10.3 ng ml-1. In this work, the characteristics of RLS, absorption, fluorescence spectra of the system were studied. The optimum reaction condition and the influencing factors on the RLS signal were investigated in detail. The proposed method was applied to the analysis of emodin in synthetic samples and human urine with satisfactory results. Furthermore, the forms of the substances under the experimental condition and the mechanism of the reaction were discussed in detail.

Lead bromide-based layered perovskite Langmuir-Blodgett films having π-conjugated molecules as organic layer prepared by using squeezed out technique

NASA Astrophysics Data System (ADS)

Era, Masanao; Shironita, Yu; Soda, Koichi

2018-03-01

Using the squeezed out technique, we successfully prepared PbBr-based layered perovskite Langmuir-Blodgett (LB) films, which have π-conjugated materials as an organic layer (i.e., a phenylenevinylene oligomer, a dithienylethene derivative, and a π-conjugated polyfluorene derivative). The mixed monolayers of π-conjugated materials and octadecylammonium bromide were spread on an aqueous subphase containing saturated PbBr2. During pressing, octadecylammonium molecules were squeezed from the mixed monolayer, and the squeezed ammonium molecules formed the PbBr-based layered perovskite structure at the air-aqueous subphase interface. The monolayers with the PbBr-based layered perovskite structure could be deposited on fused quartz substrates by the LB technique. In addition to the preparation procedure, the structural and optical properties of the layered perovskite LB films and their formation mechanism are reported in this paper.

Determination of chemical purity and isotopic composition of natural and carbon-13-labeled arsenobetaine bromide standards by quantitative(1)H-NMR.

PubMed

Le, Phuong-Mai; Ding, Jianfu; Leek, Donald M; Mester, Zoltan; Robertson, Gilles; Windust, Anthony; Meija, Juris

2016-10-01

In this study, we report the characterization of three arsenobetaine-certified reference materials by quantitative NMR. We have synthesized an arsenobetaine bromide high-purity standard of natural isotopic composition (ABET-1) and two carbon-13-labeled isotopic standards (BBET-1 and CBET-1). Assignments of the chemical purity and isotopic composition are not trivial in the case of arsenobetaine, and in this study we utilized quantitative(1)H-NMR techniques for the determination of the mass fractions (chemical purity). The isotopic purity of all three standards was also assessed by NMR from the carbon-13 satellite signals. The standards are non-hygroscopic, high-purity (ca. 0.99 g/g), and the carbon-13 enrichment for both isotopic standards is x((13)C)≈0.99. These standards are designed for use as primary calibrators for mass spectrometric determination of arsenobetaine in environmental samples.

Selective Cleavage of the Aryl Ether Bonds in Lignin for Depolymerization by Acidic Lithium Bromide Molten Salt Hydrate under Mild Conditions.

PubMed

Yang, Xiaohui; Li, Ning; Lin, Xuliang; Pan, Xuejun; Zhou, Yonghong

2016-11-09

The present study demonstrates that the concentrated lithium bromide (LiBr) solution with acid as catalyst was able to selectively cleave the β-O-4 aryl ether bond and lead to lignin depolymerization under mild conditions (e.g., in 60% LiBr with 0.3 M HCl at 110 °C for 2 h). Four industrial lignins from different pulping and biorefining processes, including softwood kraft lignin (SKL), hardwood kraft lignin (HKL), softwood ethanol organosolv lignin (EOL), and acid corncob lignin (ACL), were treated in the LiBr solution. The molecular weight, functional group, and interunit linkages of the lignins were characterized using GPC, FTIR, and NMR. The results indicated that the β-O-4 aryl ether bonds of the lignins were selectively cleaved, and both LiBr and HCl played crucial roles in catalyzing the cleavage of the ether bonds.

Grain Size Modulation and Interfacial Engineering of CH3 NH3 PbBr3 Emitter Films through Incorporation of Tetraethylammonium Bromide.

PubMed

Jamaludin, Nur Fadilah; Yantara, Natalia; Ng, Yan Fong; Li, Mingjie; Goh, Teck Wee; Thirumal, Krishnamoorthy; Sum, Tze Chien; Mathews, Nripan; Soci, Cesare; Mhaisalkar, Subodh

2018-05-07

Metal halide perovskites have demonstrated breakthrough performances as absorber and emitter materials for photovoltaic and display applications respectively. However, despite the low manufacturing cost associated with solution-based processing, the propensity for defect formation with this technique has led to an increasing need for defect passivation. Here, we present an inexpensive and facile method to remedy surface defects through a postdeposition treatment process using branched alkylammonium cation species. The simultaneous realignment of interfacial energy levels upon incorporation of tetraethylammonium bromide onto the surface of CH 3 NH 3 PbBr 3 films contributes favorably toward the enhancement in overall light-emitting diode characteristics, achieving maximum luminance, current efficiency, and external quantum efficiency values of 11 000 cd m -2 , 0.68 cd A -1 , and 0.16 %, respectively. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Aqueous photochemical reactions of chloride, bromide, and iodide ions in a diode-array spectrophotometer. Autoinhibition in the photolysis of iodide ions.

PubMed

Kalmár, József; Dóka, Éva; Lente, Gábor; Fábián, István

2014-03-28

The aqueous photoreactions of three halide ions (chloride, bromide and iodide) were studied using a diode array spectrophotometer to drive and detect the process at the same time. The concentration and pH dependences of the halogen formation rates were studied in detail. The experimental data were interpreted by improving earlier models where the cage complex of a halogen atom and an electron has a central role. The triiodide ion was shown to exert a strong inhibiting effect on the reaction sequence leading to its own formation. An assumed chemical reaction between the triiodide ion and the cage complex interpreted the strong autoinhibition effect. It is shown that there is a real danger of unwanted interference from the photoreactions of halide ions when halide salts are used as supporting electrolytes in spectrophotometric experiments using a relatively high intensity UV light source.

Dynamic Impact of Electrode Materials on Interface of Single-Crystalline Methylammonium Lead Bromide Perovskite

DOE PAGES

Tisdale, Jeremy T.; Muckley, Eric; Ahmadi, Mahshid; ...

2018-06-19

One of the current challenges in methylammonium lead halide (MAPbX 3) perovskite application research is understanding contact formation and interfacial phenomena for highly efficient and stable device performance. For semiconductors, development of contact formation is inseparable from device performance and stability. Single–crystalline MAPbX3 has become of great interest for perovskite devices in photodetectors, light–emitting diodes, and more recently in high–energy radiation detection. Deeper research is required to understand interfacial interactions in single–crystalline MAPbX 3. This article focuses on the dynamic impact of electrode metal (Au and Cr) on methylammonium lead bromide (MAPbBr 3) single crystals. It is studied how chargemore » transport properties of single crystal MAPbBr 3 can be tuned via electrode material selection at the metal/MAPbBr 3 interface to improve device performance with proper contact formation. The ability to create an ohmic–like or nonohmic contact by switching the electrode metal from Cr to Au, respectively, is demonstrated. It is observed that the interfacial charge transfer resistance (recombination resistance) of the Cr/MAPbBr 3 interface is 1.79 × 10 9 Ω, compared to 1.32 × 10 7 Ω for the Au/MAPbBr 3. Cr contacts can reduce hysteretic behavior by reducing interfacial recombination and interfacial polarization. Furthermore, these studies provide insight to metal/MAPbX 3 interfacial interactions toward device engineering for hole transport layer–free MAPbX 3 device structures.« less

Dynamic Impact of Electrode Materials on Interface of Single-Crystalline Methylammonium Lead Bromide Perovskite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tisdale, Jeremy T.; Muckley, Eric; Ahmadi, Mahshid

One of the current challenges in methylammonium lead halide (MAPbX 3) perovskite application research is understanding contact formation and interfacial phenomena for highly efficient and stable device performance. For semiconductors, development of contact formation is inseparable from device performance and stability. Single–crystalline MAPbX3 has become of great interest for perovskite devices in photodetectors, light–emitting diodes, and more recently in high–energy radiation detection. Deeper research is required to understand interfacial interactions in single–crystalline MAPbX 3. This article focuses on the dynamic impact of electrode metal (Au and Cr) on methylammonium lead bromide (MAPbBr 3) single crystals. It is studied how chargemore » transport properties of single crystal MAPbBr 3 can be tuned via electrode material selection at the metal/MAPbBr 3 interface to improve device performance with proper contact formation. The ability to create an ohmic–like or nonohmic contact by switching the electrode metal from Cr to Au, respectively, is demonstrated. It is observed that the interfacial charge transfer resistance (recombination resistance) of the Cr/MAPbBr 3 interface is 1.79 × 10 9 Ω, compared to 1.32 × 10 7 Ω for the Au/MAPbBr 3. Cr contacts can reduce hysteretic behavior by reducing interfacial recombination and interfacial polarization. Furthermore, these studies provide insight to metal/MAPbX 3 interfacial interactions toward device engineering for hole transport layer–free MAPbX 3 device structures.« less

Role of a novel pyridostigmine bromide-phospholipid nanocomplex in improving oral bioavailability.

PubMed

Tan, Qun-you; Hu, Ni-ni; Liu, Guo-dong; Yin, Hua-feng; Zhang, Li; Wang, Hong; Lu, Lu-yang; Zhang, Jing-qing

2012-03-01

A novel pyridostigmine bromide (PB)-phospholipid nanocomplex (PBPLC) was prepared to increase the bioavailability of PB. A central composite design approach was employed for process optimization. The physicochemical properties of PBPLC were investigated by means of differential scanning calorimetry, ultraviolet spectroscopy, Fourier transformed infrared spectroscopy and the n-octano/water partition coefficient. The intestinal permeability of PBPLC was observed via a single pass intestinal perfusion in rats. After oral administration of PBPLC, the concentrations of PB at predetermined time points were determined by HPLC, and the pharmacokinetic parameters were computed by DAS 2.1.1 software. Multiple linear regression analysis for process optimization revealed that the optimal PBPLC was obtained when the values of X(1), X(2), and X(3) were 8, 40°C, and 4 mg/mL, respectively. The average particle size and zeta potential of PBPLC with the optimized formulation were 204.60 nm and -25.12 mV, respectively. Non-covalent interactions between PB and phospholipids were found in the PBPLC. The n-octanol/water partition coefficient of PBPLC was substantially increased. PBPLC had better intestinal permeability in comparison with free PB. Mean plasma drug concentration-time curves of PBPLC and free PB after oral administration were both in accordance with the two-compartment open model. The values of pharmacokinetic parameters of PBPLC and free PB were the peak time (T(max)) 2 h vs 2 h, the maximum concentration (C(max)) 22.79 μg/mL vs 6.00 μg/mL, and the value of the area under the concentration vs time curve (AUC(0-∞)) 7128.21 μg·min/mL vs 1772.36 μg·min/mL, respectively. In conclusion, compared with free PB, PBPLC remarkably improves the oral bioavailability of PB, which is likely due to its higher lipophilicity and permeability.

Synthesis of silver nano-materials from Grevillea robusta A Cunn (Silver-oak tree) leaves extract and shape directing role of cetyltrimethylammonium bromide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ahmad, Rabia; Faisal, Qamer; Hussain, Sajjad

Grevillea robusta (Silver-oak tree) tree is a medicinal tree. Conventional UV-visible spectrophotometric and transmission electron microscopic technique were used to determine the morphology of silver nanoplates (AgNP) using Grevillea robusta (Silver-oak tree) aqueous leaves extract for the first time. The visible spectra showed the presence of three well defined surface plasmon absorption (SPR) bands at 500, 550 and 675 nm which was attributed to the anisotropic growth of Ag-nanoplates. Transmission electron microscopic (TEM) analysis of AgNP showed formation of truncated triangular, polyhedral with some irregular shapes nanoplates in the size range 8-20 nm. Cetyltrimethylammonium bromide (CTAB) has no significant effect on themore » shape of the spectra, position of SPR bands, size and size distribution of AgNP.« less