Science.gov

Sample records for explosion physique des

  1. Etudes physiques des mélanges eau-cryoprotecteurs

    NASA Astrophysics Data System (ADS)

    Vassoille, R.; Perez, J.

    The aim of the following review is to present the most important studies concerning the physical properties of water-solutes mixtures used in cryobiology. Cryobiology is a branch of biology which deals with the very low temperature behaviour of cells. This technique is developed today in several directions. The creation of banks of cells and perhaps in a short time of small organs, is the purpose of much research in this domain. Before freezing, living cells are generally put in a solution containing one or more solutes. The role of these solutes is to protect the cells against damage due to crystallization of water (cryoprotectors). The mechanisms of cryoprotection are not well known ; nevertheless the vitreous state formation during cooling is often invoked. So, it is possible to avoid crystallization damage such as mechanical strain (due to an increase of volume of about 10 %) and salt effects (due to osmotic pressure). The conditions in which the vitreous state is obtained, maintained during cooling, storage at low temperature and rewarming can be defined by physical studies presented in the following review. Le présent travail est essentiellement une revue bibliographique des principales études physiques qui ont été réalisées avec des solutions de composés habituellement employés en cryobiologie. La cryobiologie est une branche de la biologie qui s'intéresse au comportement des cellules à basse température. Cette discipline est actuellement en plein développement dans des domaines très divers. Son principal but est la création de banques de cellules de plus en plus complexes avec comme perspective la conservation des organes. Les cellules vivantes sont généralement placées avant congélation dans une solution contenant divers composés dont le rôle est de protéger les cellules contre les effets de la cristallisation de l'eau. L'action protectrice de ces cryoprotecteurs est encore mal connue; cependant, la formation d'un état vitreux lors du

  2. Une vie saine et active : des directives en matière d’activité physique chez les enfants et les adolescents

    PubMed Central

    Lipnowski, Stan; LeBlanc, Claire MA

    2012-01-01

    RÉSUMÉ L’épidémie d’obésité juvénile augmente partout dans le monde. Même si les facteurs de risque d’obésité sont multifactoriels, bon nombre sont liés au mode de vie et se prêtent à une intervention. Ces facteurs incluent le comportement sédentaire et la thermogenèse sans activité physique, de même que la fréquence, l’intensité, la quantité et le type d’activité physique. Les dispensateurs de soins de première ligne sont en position idéale pour surveiller le taux d’activité physique des enfants, des adolescents et de leur famille, évaluer les choix liés au mode de vie et offrir des conseils pertinents. Le présent document de principes contient des directives visant à réduire le comportement sédentaire et à accroître le taux d’activité physique au sein de la population pédiatrique. Des recommandations d’activités physiques adaptées au développement et visant les nourrissons, les tout-petits, les enfants d’âge préscolaire, les enfants et les adolescents sont présentées. Des stratégies de promotion d’une vie saine et active sur les scènes locale, municipale, provinciale, territoriale et fédérale sont proposées.

  3. Dépistage des maladies cardiovasculaires chez des étudiants de l'Université de Douala et influence des activités physiques et sportives

    PubMed Central

    Ewane, Marielle Epacka; Mandengue, Samuel Honoré; Priso, Eugene Belle; Tamba, Stéphane Moumbe; Ahmadou; Fouda, André Bita

    2012-01-01

    Introduction Les maladies cardiovasculaires (MCV) constituent l'une des principales causes de mortalité dans les pays en développement. Le dépistage de ces dernières chez des jeunes est un défi dans la lutte contre leur expansion. Le but de cette étude était de dépister ces maladies au sein d'une population jeunes d’étudiants camerounais. Methodes Deux mille six cent cinquante-huit étudiants de l'Université de Douala (23,6 ± 2,9 ans, sex-ratio H/F = 0,9) ont en Avril - Mai 2011 participé à une campagne de dépistage gratuit du diabète, de l'hypertension artérielle (HTA) et de l'obésité. Ils ont également été soumis à une d'enquête évaluant leur niveau en activités physiques et sportives (APS). Resultats 12,7% des participants avaient une pression artérielle (PA) ≥ 140/90 mmHg, 3,6% étaient obèses et 0,9% avaient une glycémie ≥1,26 g/L. Des corrélations ont été trouvées entre certains facteurs de risque (diabète, hypertension et obésité) et le niveau académique d'une part (r =0,366; p < 0,0001) et le temps passé devant la télévision d'autres part (r = 0,411; p < 0,0001). L‘APS était inversement corrélée à l‘âge (r =-0,015; p < 0,0001) et au temps passé devant la télévision (r = -0,059; p = 0,002). Conclusion La présence des MCV et leurs facteurs de risque mis en évidence dans cette étude réalisée en milieu estudiantin camerounais interpelle à une prévention et une éducation dans la lutte contre ces dernières. PMID:22655111

  4. Traitements didactiques preventifs d'un type de conceptions erronees en sciences physiques chez des eleves du secondaire

    NASA Astrophysics Data System (ADS)

    Blondin, Andre

    Dans un contexte constructiviste, les connaissances anterieures d'un individu sont essentielles a la construction de nouvelles connaissances. Quelle qu'en soit la source (certaines de ces connaissances ont ete elaborees en classe, d'autres ont ete elaborees par interaction personnelle de l'individu avec son environnement physique et social), ces connaissances, une fois acquises, constituent les matieres premieres de l'elaboration des nouvelles conceptions de cet individu. Generalement, cette influence est consideree comme positive. Cependant, dans un milieu scolaire ou l'apprentissage de certaines conceptions enchassees dans un programme d'etudes et enterinees par l'ensemble d'une communaute est obligatoire, certaines connaissances anterieures peuvent entraver la construction des conceptions exigees par la communaute. La litterature abonde de tels exemples. Cependant, certaines connaissances anterieures, en soi tout a fait conformes a l'Heritage, peuvent aussi, parce qu'utilisees de facon non pertinente, entraver la construction d'une conception exigee par la communaute. Ici, la litterature nous donne peu d'exemples de ce type, mais nous en fournirons quelques-uns dans le cadre theorique, et ce sera un d'entre eux qui servira de base a nos propos. En effet, une grande proportion d'eleves inscrits a un cours de sciences physiques de la quatrieme secondaire, en reponse a un probleme deja solutionne durant l'annee et redonne lors d'un examen sommatif, "Pourquoi la Lune nous montre-t-elle toujours la meme face?", attribue principalement la cause de ce phenomene a la rotation de la Terre sur son axe. En tant que responsable de l'enseignement de ce programme d'etudes, plusieurs questions nous sont venues a l'esprit, entre autres, comment, dans un contexte constructiviste, est-il possible de reduire chez un eleve, l'impact de cette connaissance anterieure dans l'elaboration de la solution et ainsi prevenir la construction d'une conception erronee? Nous avons teste nos

  5. Origine physique du contraste entre activité électrique au dessus des terres et des océans

    NASA Astrophysics Data System (ADS)

    Williams, Earle; Stanfill, Sharon

    2002-12-01

    New tests and older ideas are explored to understand the origin of the pronounced contrast in lightning between land and sea. The behavior of islands as miniature continents with variable area supports the traditional thermal hypothesis over the aerosol hypothesis for lightning control. The substantial land-ocean contrast in updraft strength is supported globally by TRMM (Tropical Rainfall Measuring Mission) radar comparisons of mixed phase radar reflectivity. The land-ocean updraft contrast is grossly inconsistent with the land-ocean contrast in CAPE (Convective Available Potential Energy), from the standpoint of parcel theory. This inconsistency is resolved by the scaling of buoyant parcel size with cloud base height, as suggested by earlier investigators. Strongly electrified continental convection is then favored by a larger surface Bowen ratio, and by larger, more strongly buoyant boundary layer parcels which more efficiently transform CAPE to kinetic energy of the updraft in the moist stage of conditional instability. To cite this article: E. Williams, S. Stanfill, C. R. Physique 3 (2002) 1277-1292.

  6. La physique des tas de sable Description phénoménologique de la propagation des contraintes dans les matériaux granulaires

    NASA Astrophysics Data System (ADS)

    Claudin, Ph.

    This work deals with the stress distribution in dry granular media such as sand. As a matter of fact, the granular family is amazingly wide: raw materials used in building, chemical or food industries are made of little grains. Predicting how forces propagate and fluctuate into granular media is then a real and concrete challenge. This goal is not easy to reach. One reason is that the stress distribution is strongly inhomogeneous: the forces applied on a granular system will be supported almost entirely by a fraction of the grains which form chains, or arches. As a consequence, the stress profile beneath a sandpile depends on the way that the pile was built. In order to describe quantitatively these effects, we proposed a phenomenological friction relation between arches. The differential equations which come out from this modelling are of hyperbolic type, which means that there exists particular lines for propagation called characteristics. We managed to match these characteristics with arches. These models fit well with experimental data, and can explain for example the dip of pressure observed beneath the apex of a pile made with a hopper. They also significantly improve Janssen's predictions for the silo. We also looked at stress fluctuations, and showed that granular material are intrinsically fragile when subjected to changing external forces or perturbations. This property has been particulary studied within a scalar arching model with which we were able to visualize changes of stress paths and subsequent changes of the stress distribution. Ce travail porte sur la description de la manière dont les forces se propagent dans les milieux granulaires comme le sable. Cette catégorie de matériaux est en fait très vaste, et pouvoir prédire de manière satisfaisante la répartition des contraintes au sein d'un système granulaire est un enjeu industriel réel et concret. Or ceci est difficile. Une des raisons en est que cette répartition est très inhomog

  7. Obésité, activité physique et temps de sédentarité chez des adolescents scolarisés, âgés de 15 à 18 ans de la ville de Sfax (Tunisie)

    PubMed Central

    Regaieg, Sofien; Charfi, Nadia; Elleuch, Mouna; Mnif, Fatma; Marrakchi, Rim; Yaich, Sourour; Jammousi, Kamel; Damak, Jamel; Abid, Mohamed

    2015-01-01

    Introduction Le but de notre étude était d’évaluer la prévalence du surpoids et de l'obésité chez des adolescents scolarisés dans la ville de Sfax mais aussi, d’étudier son association avec le temps de sédentarité et l'activité physique (AP). Méthodes La population étudiée était composée de 1695 adolescents âgés de 15-18 ans. Tous les participants avait rempli un questionnaire porté sur leurs activités physiques et temps de sédentarité, donné lors d'un entretien direct. Le niveau d'AP était évalué avec l'International Physical Activity Questionnaire (IPAQ) version courte. Résultats Notre étude comportait 43,7% de garçons et 56,3% de filles. L’âge moyen était de 16,78 ± 1, 1 an. Dans notre échantillon, 23,4% des adolescents étaient en surpoids ou obèses. Le score de l'IPAQ nous a montré que le niveau d'AP de nos participants était faible dans 6,4%, modéré dans 65,4% et élevé dans 28,2% des cas. Nos résultats avaient démontré que l'augmentation du temps de sédentarité (plus de 2 h / jour) est associée à une augmentation significative de l'indice de masse corporelle (IMC) et du tour de taille (TT) (P <0,001). Alors qu'un niveau d'AP élevé et/ou la participation aux séances d'AP structurées dans le cadre scolaire et hors scolaire est accompagnée par une diminution significative de l'IMC et du TT (P <0,001). Conclusion Nos résultats apportent une preuve supplémentaire sur la nécessité de promouvoir la vie active chez les jeunes Tunisiens. PMID:27022430

  8. Fibrillation auriculaire et activité physique

    PubMed Central

    Bosomworth, N. John

    2015-01-01

    Résumé Objectif Examiner les données probantes portant sur les effets de divers niveaux d’activité physique sur l’incidence de fibrillation auriculaire (FA) dans la population générale et chez les athlètes d’endurance. Sources des données Une recherche a initialement été menée sur PubMed à l’aide des titres MeSH ou des mots-de-texte anglais (avec descripteur de zone de recherche TIAB [title and abstract]) atrial fibrillation et exercise ou physical activity ou athlet* ou sport*, sans filtre additionnel. Le système GRADE (grading of recommendations, assessment, development, and evaluation) a été utilisé pour tirer les conclusions au sujet de la qualité et du niveau de preuve. Sélection des études Aucune étude d’intervention n’est ressortie de la recherche. Les études d’observation ont alors été jugées acceptables et, bien que des études prospectives de cohortes à long terme de plus grande envergure auraient été préférables, des essais cas-témoins ou transversaux ont aussi été inclus dans cette révision. Synthèse Les données disponibles laissent croire à un lien proportionnel à la dose entre l’exercice plus intense et l’incidence réduite de FA chez les femmes. Il en va de même pour les hommes dont le niveau d’activité physique est de faible à modéré. Chez les hommes seulement, l’activité intense est associée à un risque accru de FA et ce, dans la plupart des études, mais pas la totalité d’entre elles. Ce risque est modéré, le rapport de risque instantané étant de 1,29 dans l’une des études de meilleure qualité. Le risque de FA chez la plupart des personnes régulièrement actives est plus faible que le risque observé dans la population sédentaire appariée. Conclusion La fibrillation auriculaire est probablement moins fréquente à mesure que le niveau d’activité physique augmente, la relation dose-réponse étant démontrable. À toutes les intensités, l’exercice doit être

  9. La physique des bulles de champagne Une première approche des processus physico-chimiques liés à l'effervescence des vins de Champagne

    NASA Astrophysics Data System (ADS)

    Liger-Belair, G.

    2002-07-01

    bubbles collapsing at a free surface. But, to the best of our knowledge, and surprising as it may seem, no results concerning the collateral effects on adjoining bubbles of bubbles collapsing in a bubble monolayer have been reported up to now. Actually, effervescence in a glass of champagne ideally lends to a preliminary work with bubbles collapsing in a bubble monolayer. For a few seconds after pouring, the free surface is completely covered with a monolayer composed of quite monodisperse millimetric bubbles collapsing close to each others. We took high-speed photographs of the situation which immediately follows the rupture of a bubble cap in a bubble monolayer. Adjoining bubbles were found to be literally sucked and strongly stretched toward the lowest part of the cavity left by the bursting bubble, leading to unexpected and short-lived flower-shaped structures. Stresses in distorted bubbles (petals of the flower-shaped structure) were evaluated and found to be, at least, one order of magnitude higher than stresses numerically calculated in the boundary layer around an isolated single millimetric collapsing bubble. This is a brand-new and slightly counter-intuitive result. While absorbing the energy released during collapse, as an air-bag would do, adjoining bubble caps store this energy into their thin liquid film, leading finally to stresses much higher than those observed in the boundary layer around single millimetric collapsing bubbles. Further investigation should be conducted now, and especially numerically, in order to better understand the relative influence of each pertinent parameters (bubble size, liquid density and viscosity, effect of surfactant...) on bubble deformation. L'objectif général de cet ouvrage consacré à l'étude des processus physico- chimiques de l'effervescence des vins de Champagne était de décortiquer les différentes étapes de la vie d'une bulle de champagne en conditions réelles de consommation, dans une flûte. Nous r

  10. U Modele pour L'enregistrement et L'interpretation Physique D'images Tridimensionnelles EN Couleur

    NASA Astrophysics Data System (ADS)

    Baribeau, Rejean

    Le modele propose dans cette these repose sur l'utilisation d'un capteur de vision tridimensionnelle, couple a un laser RGB, pour la saisie des coordonnees surfaciques d'un objet de meme que des couleurs associees. Une calibration du capteur et l'exploitation des donnees 3D permettent la recuperation des facteurs de reflectance spectrale des elements de surface. On montre que la performance du systeme est limitee par le speckle, et une analyse quantitative du phenomene est proposee. Divers modeles de reflexion sont ensuite etablis puis appliques a l'extraction des parametres physiques intrinseques d'objets dans des scenes 3D en couleur. Une telle modelisation physique facilite la tache d'interpretation et permet plus de souplesse dans la manipulation des objets sous forme de realites virtuelles.

  11. Evaluation du niveau d'activité physique dans un service Marocain d'hémodialyse chronique

    PubMed Central

    Karimi, Ilham; Benabdellah, Nawal; Bentata, Yassamine; Yacoubi, Hicham; Haddiya, Intissar

    2013-01-01

    Introduction L'activité physique est souvent réduite chez le patient hémodialysé chronique. Plusieurs études ont montré l'intérêt du maintien ou de la reprise d'une activité physique sur l’état de santé des patients. Le but de notre travail est d'analyser le niveau d'activité physique chez nos patients hémodialysé chronique. Méthodes Nous avons réalisé une étude transversale au centre d'hémodialyse de l'hôpital Al Farabi d'Oujda. Nous avons évalué l'activité physique de nos patients à l'aide du Questionnaire de Baecke traduit en dialectal Marocain et adapté au contexte socioculturel Marocain. Nous avons relevé les paramètres démographiques et clinico-biologiques ainsi que le niveau d'activité physique. L'analyse statistique est réalisée par le logiciel SPSS 11.5. Résultats Notre étude a inclus 83 patients. L’âge moyen était de 47,3±13,2 ans, avec une prédominance masculine. 15,6% déclarent n'avoir aucune activité physique. 68% des patients rapportent des difficultés à effectuer des efforts physiques importants (courir, soulever un objet lourd). 16,4% des patients déclarent avoir une activité physique et sportive régulière (marche, foot-ball etc..). La diminution de l'activité physique est corrélée de façon significative à l’âge avancée, l'indice de masse corporelle bas, l'ancienneté en hémodialyse et les affections cardio-vasculaires. Conclusion Un programme d'activité physique adapté à notre population d'hémodialysés et élaboré en concertation pluridisciplinaire (cardiologues, orthopédistes, rhumatologues, kinésithérapeutes) paraît intéressant dans le cadre d'une prise en charge globale du patient hémodialysé chronique. PMID:24198881

  12. Contractions Graduees D'algebres de Lie et Applications EN Physique

    NASA Astrophysics Data System (ADS)

    de Montigny, Marc

    1992-01-01

    La theorie des contractions d'algebres de Lie constitue une methode formelle par laquelle sont relies les groupes (algebres) de Lie de differents systemes physiques. Elles consistent en une procedure limite qui implique une relation analogue entre les systemes (ou theories) physiques consideres, et comblent ainsi notre tendance naturelle a unifier notre comprehension de la Nature. Une introduction historique, de meme qu'un bref survol du corps de la these, constituent le premier chapitre. Le chapitre 2 consiste en l'article essentiel de la these: la description des contractions graduees d'algebres de Lie. Cette methode s'applique a toute algebre (ou superalgebre) de Lie de dimension finie ou infinie. La methode associee de contraction de representations n'est pas contenue integralement dans le present texte, mais expliquee brievement dans l'introduction (Chapitre 1), puisque sa formulation originale est due a R. V. Moody et J. Patera. Le chapitre 3 contient un article decrivant un programme developpe pour faire generer et resoudre par ordinateur les equations determinantes des contractions d'algebres de Lie et de leurs representations. Avec le quatrieme chapitre, nous commencons a appliquer a la physique la methode decrite precedemment. Il s'agit d'un article dans <=uel certains resultats contenus dans la litterature sont reformules dans le contexte des contractions graduees. Plus precisement, les groupes cinematiques de la Nature sont obtenus en contractant les groupes de de Sitter, tout en preservant une graduation generee par les automorphismes de changement de parite et de renversement du temps. Le chapitre 5 contient une etude systematique des contractions graduees de l'algebre de Lie simple complexe B_2, la complexification des algebres de Lie des groupes de de Sitter. Le chapitre 6 ne concerne pas directement les contractions graduees, mais se veut une parenthese sur la theorie des representations des groupes de de Sitter. On y calcule les signatures des

  13. Preadolescent male perceptions of action figure physiques.

    PubMed

    Baghurst, Timothy; Carlston, David; Wood, Julie; Wyatt, Frank B

    2007-12-01

    This study investigated the preference and reasoning of 176 preadolescent and adolescent males when presented with original and current action figures that had statistically different physiques. Current action figures were perceived as significantly more muscular and healthier. Participants also preferred to resemble current action figures citing muscularity and size for their preference. PMID:18023792

  14. Highly explosive eruption of the monogenetic 8.6 ka BP La Vache et Lassolas scoria cone complex (Chaîne des Puys, France)

    NASA Astrophysics Data System (ADS)

    Jordan, S. C.; Le Pennec, J.-L.; Gurioli, L.; Roche, O.; Boivin, P.

    2016-03-01

    The eruption of the trachy-basaltic La Vache and Lassolas cone complex was the youngest eruption (ca. 8.6 ka BP) and one of the most violent in the Chaîne des Puys, France. Here we present field data and results of grain size, componentry and clast density measurements of different layers of the widespread tephra deposit that is associated with this cone-forming eruption. Our data indicates five main eruption phases comprising a vent-opening phase, a second sustained highly explosive phase, a third and fourth violent Strombolian phase and a fifth dominantly effusive phase. The layer formed by the opening phase is rich in lithic material, which was previously considered to be the result of phreatomagmatic activity. The data presented here on the componentry and textures of the pyroclastic material contradict this hypothesis. We propose instead that the material of the basal layer results from fragmentation caused by the explosion of a first arriving gas-dominated phase. The variations in eruption intensity during the main eruption phases are interpreted here to be the result of gas segregation within the plumbing system and fluxes in the magma ascent rate during the eruption. Significant amount of gas segregation is indicated by the deposition of both gas-poor and gas-rich material and by the presence of plate tephra. This is also supported by the simultaneous ejection of tephra and lava from both cones during most of the explosive activity. We suggest that gas segregation occurred within shallow intrusions and that fresh ascending material in the main conduit mixed with degassed material that flow back into the conduit from the intrusion before fragmentation. The interaction of the ascending magma and the opening of intrusions may have controlled the evolution and explosivity of the eruption. The high explosivity at the beginning of the eruption and the wide dispersal area, demonstrate that scoria cone eruptions in monogenetic fields can impose a major threat to

  15. L’explosion intravésicale au cours des procédures de résection endoscopique: Un incident dangereux qui peut être évité

    PubMed Central

    Anzaoui, Jihad El; Abakka, Najib; El harrech, Younes; Ghoundale, Omar; Touiti, Driss; Lahkim, Mohammed; Fihri, Jawad Fassi; Bakzaza, Walid; Mejdane, Abdelhadi

    2013-01-01

    Résumé Les explosions survenant au cours des manœuvres endoscopiques urologiques sont rares et dangereuses. Elles sont dues à une production d’hydrogène par hydrolyse de l’eau lors des procédés de coagulation et de section. L’hydrogène devient très combustible une fois mélangé avec l’oxygène ambiant. Nous rapportons un cas d’explosion intravésicale au cours d’une résection transurethrale d’une tumeur de la vessie et nous exposons, par une revue de littérature, les différentes théories physiopathologiques et les moyens de prévention. PMID:23914274

  16. Explosives tester

    DOEpatents

    Haas, Jeffrey S.; Howard, Douglas E.; Eckels, Joel D.; Nunes, Peter J.

    2011-01-11

    An explosives tester that can be used anywhere as a screening tool by non-technical personnel to determine whether a surface contains explosives. First and second explosives detecting reagent holders and dispensers are provided. A heater is provided for receiving the first and second explosives detecting reagent holders and dispensers.

  17. Partager : des technologies de pointe au service de la société

    ScienceCinema

    None

    2011-10-06

    Médecine, climatologie, métrologie et informatique, les techniques utilisées par le LHC trouvent déjà des répercussions dans d?autres domaines scientifiques. Utilisant des techniques inédites, la physique des particules en fait bénéficier la société toute entière.

  18. Accidental explosions

    SciTech Connect

    Medard, L.A.

    1989-01-01

    This book presents a survey of accidental explosions, their nature and their causes. It covers the physical and chemical conditions governing accidental explosions, whether in the gas phase, or in the liquid or solid state. The theoretical background of the kinetics and thermochemistry of explosions is outlined, followed by a detailed study of the explosion and detonation properties of both gas and condensed explosives. The author surveys a wide variety of substances in daily use in industry which can give rise to accidental explosions. Their properties and hazards are spelt out in detail, the discussion drawing on a long history of sometimes catastrophic accidents. Includes case studies, tables of physical and chemical data.

  19. Influence of players' physique on rugby football injuries.

    PubMed Central

    Lee, A J; Myers, J L; Garraway, W M

    1997-01-01

    OBJECTIVES: To determine whether there is an association between a player's physique and injuries incurred while playing rugby football. METHODS: A cohort study was carried out involving all senior rugby clubs in the Scottish Borders during the 1993-1994 rugby season. Somatotype estimates were determined for 1152 (95%) of the 1216 eligible players. Body mass index (BMI), chest to waist ratio, and the ponderal index (PI) were used to classify players' physique as endomorphic (obese), mesomorphic (muscular), and ectomorphic (linear). RESULTS: A strong association was found between physique and age (chi 2 test: chi 2 = 317.2, df = 10, P < 0.0001). More younger players were ectomorphs. Older players were more often endomorphic. The physiques of forwards and backs were significantly different (chi 2 test: chi 2 = 58.6, df = 2, P < 0.0001), with forwards being of a heavier build than three-quarters, even after adjustment for age. Endomorphic players were more likely than ectomorphs to be injured in a match after adjustment for age (age-adjusted mean BMI for players who were injured in a match was 25.4 compared with 24.6 for players who were not injured in a match, P < 0.0001; adjusted chest to waist ratio means were 1.136 and 1.125 respectively, P = 0.0307; adjusted PI means were 0.414 and 0.417 respectively, P = 0.0056). Increased risk of injury may occur when players play out of position, since one fifth of all injuries occurred in this circumstance. CONCLUSIONS: Further research needs to be conducted using a more objective method of measuring somatotype on a further cohort of players so that the risk of injury for different body types can be examined more closely and related to other potential confounding factors. The level of increased risk for individuals playing out of their usual playing position needs to be established with a greater degree of certainty. PMID:9192128

  20. Social physique anxiety and disordered eating: what's the connection?

    PubMed

    Diehl, N S; Johnson, C E; Rogers, R L; Petrie, T A

    1998-01-01

    Social physique anxiety (SPA) is highly correlated with other body image measures that have been considered to be important in understanding eating disorders. However, SPA has not been directly studied with respect to eating disorders. Thus, the purpose of this investigation was to examine the link between SPA and measures of eating disorder symptomatology to determine if SPA should be considered as an additional risk factor in the prediction of eating disturbances. One hundred and sixty female undergraduates completed questionnaires measuring body mass index (BMI), social physique anxiety (SPAS), anorexic symptoms (EAT), bulimic symptoms (BULIT-R), depression (CES-D), self-esteem (SES) and obligatory exercise (OEQ). Regression analyses revealed that SPA and depression were the psychological correlates that predicted bulimic symptomatology and that SPA, depression, and obligatory exercise predicted anorexic symptomatology; all variables were positively related to eating disorder symptoms. Overall, the results indicate that social physique anxiety appears to be a useful construct for understanding eating disorder symptoms in female undergraduates. PMID:9468735

  1. Insensitive explosive

    SciTech Connect

    Lee, Kien-yin; Storm, C.B.

    1991-12-31

    This invention relates to the field of chemistry and, more particularly, to explosives. This invention is the result of a contract with the Department of Energy (Contract No. W-7405-ENG-36). It is desirable to use explosives in weapons and other applications which are less sensitive than the common explosives RDX, TNT, and HMX, since there have been catastrophic explosions of munitions which use these compounds. In preliminary characterization and sensitivity testing, it has been found that 3-amino-5-nitro-1,2,4-triazole (ANTA) is a promising insensitive high explosive. This report details the safety, production, and physical properties of ANTA.

  2. Physique and Body Composition in Soccer Players across Adolescence

    PubMed Central

    Nikolaidis, Pantelis Theodoros; Vassilios Karydis, Nikos

    2011-01-01

    Purpose Although the contribution of physique and body composition in soccer performance was recognized, these parameters of physical fitness were not well-studied in adolescent players. Aim of this study was to investigate physique and body composition across adolescence. Methods Male adolescents (N=297 aged 12.01–20.98 y), classified into nine one-year age-groups, child (control group, N=16 aged 7.34–11.97 y) and adult players (control group, N=29 aged 21.01–31.59 y), all members of competitive soccer clubs, performed a series of anthropometric measures (body mass, height, skinfolds, circumferences and girths), from which body mass index (BMI), percentage of body fat (BF%), fat mass (FM), fat free mass (FFM) and somatotype (Heath-Carter method) were calculated. Results Age had a positive association with FM (r=0.2, P<0.001) and FFM (r=0.68, P<0.001), and a negative association with BF (r=−0.12, P=0.047). Somatotype components changed across adolescence as well; age was linked to endomorphy (r=−0.17, P=0.005), mesomorphy (r=0.14, P=0.019) and ectomorphy (r=−0.17, P=0.004). Compared with age-matched general population, participants exhibited equal body mass, higher stature, lower body mass index and lower BF. Conclusion During adolescence, soccer players presented significant differences in terms of body composition and physique. Thus, these findings could be employed by coaches and fitness trainers engaged in soccer training in the context of physical fitness assessment and talent identification. PMID:22375222

  3. Social Physique Anxiety, Obligation to Exercise, and Exercise Choices among College Students

    ERIC Educational Resources Information Center

    Chu, Hui-Wen; Bushman, Barbara A.; Woodard, Rebecca J.

    2008-01-01

    Objective: The authors examined relationships among social physique anxiety, obligation to exercise, and exercise choices. Participants and Methods: College students (N = 337; 200 women, 137 men) volunteered to complete 3 questionnaires: the Social Physique Anxiety Scale (SPAS), Obligatory Exercise Questionnaire (OEQ), and Physical Activity…

  4. Does Body Mass Index Influence Behavioral Regulations, Dispositional Flow and Social Physique Anxiety in Exercise Setting?

    PubMed Central

    Ersöz, Gözde; Altiparmak, Ersin; Aşçı, F. Hülya

    2016-01-01

    The purpose of this study was to examine differences in behavioral regulations, dispositional flow, social physique anxiety of exercisers in terms of body mass index (BMI). 782 university students participated in this study. Dispositional Flow State Scale-2, Behavioral Regulations in Exercise Questionnaire-2, Social Physique Anxiety Scale and Physical Activity Stages of Change Questionnaire were administered to participants. After controlling for gender, analysis indicated significant differences in behavioral regulations, dispositional flow and social physique anxiety of exercise participants with regards to BMI. In summary, the findings demonstrate that normal weighted participants exercise for internal reasons while underweighted participants are amotivated for exercise participation. Additionally, participants who are underweight had higher dispositional flow and lower social physique anxiety scores than other BMI classification. Key points Normal weighted participants exercise for internal reasons. Underweighted participants are amotivated for exercise participation. Underweighted participants had higher dispositional flow. Underweighted participants have lower social physique anxiety scores than normal weighted, overweight and obese participants. PMID:27274667

  5. The perioperative changes in physical function and physique of patients with gastrointestinal cancer

    PubMed Central

    Hara, Tsuyoshi; Kubo, Akira

    2015-01-01

    [Purpose] The purpose of this study was to observe the long-term change in physical function and physique from perioperative to discharge of patients with gastrointestinal cancer. [Subjects and Methods] Subjects were 47 perioperative patients with gastrointestinal cancer [25 men and 22 women aged 61.3 ± 11.0 years (mean ± SD)]. Six-minute walk distance was measured for physical function and body mass index and calf circumference were measured for physique. These items were evaluated at three time points: before surgery, after surgery, and after discharge. [Results] Significant declines in physical function and physique were observed temporarily after surgery. Physical function improved equally before surgery in after discharge. On the other hand, postoperative physique was significantly lower than that observed pre-operatively. [Conclusion] These results suggest that the perioperative changes in physical function and physique follow different courses in patients with gastrointestinal cancer. PMID:25931710

  6. Un fusible de méthane pour l'explosion cambrienne : les cycles du carbone et dérive des pôles

    NASA Astrophysics Data System (ADS)

    Kirschvink, Joseph L.; Raub, Timothy D.

    2003-01-01

    The dramatic diversification of animal groups known as the Cambrian Explosion (evolution's 'Big Bang') remains an unsolved puzzle in Earth Science. The Vendian-Cambrian interval is characterized by anomalously high rates of apparent plate motion, interpreted as True Polar Wander (TPW), and by more than a dozen large, high-frequency perturbations in carbon isotopes that dwarf all others observed through the past 65 million years. We suggest that these biological, tectonic, and geochemical events are intimately related in the following fashion. First, tropical continental margins and shelf-slopes which formed during fragmentation of the supercontinent Rodinia accumulated massive quantities of isotopically-light organic carbon during Late Neoproterozoic time, as indicated by strikingly heavy isotope ratios in inorganic carbon during interglacial intervals. Second, an initial phase of Vendian TPW moved these organic-rich deposits to high latitude, where conditions favored trapping biogenic methane in layers of gas hydrate and perhaps permafrost. Continued sedimentation during Late Vendian time added additional hydrate/gas storage volume and stabilized underlying units until the geothermal gradient moved them out of the clathrate stability field, building up deep reservoirs of highly pressurized methane. Finally, a burst of TPW brought these deposits back to the Tropics, where they gradually warmed and were subjected to regional-scale thermohaline eddy variation and related sedimentation regime changes. Responding to the stochastic character of such changes, each reservoir reached a critical failure point independently at times throughout the Cambrian. By analogy with the Late Paleocene Thermal Maximum event, these methane deposits yield transient, greenhouse-induced pulses of global warming when they erupt. Temperature correlates powerfully with biodiversity; the biochemical kinetics of metabolism at higher temperature decrease generation time and maintain relatively

  7. Explosive Entrances

    NASA Technical Reports Server (NTRS)

    1976-01-01

    Explosive Technology, Inc. manufactured explosives first used by NASA to separate stages of the Gemini launch vehicle. When firemen need to get into a burning building or chop a hole to provide ventilation, axes can be devastatingly slow. Controlled explosives developed to separate manned upper stages of space rockets in case of mishap have been adapted to cutting emergency exits and demolishing unsafe buildings and bridges. Detonation cuts through thick steel girders or other materials more cleanly than torches or saws. This device can also cut emergency holes in airplanes and trains so surviving passengers can escape.

  8. The influence of exercise identity and social physique anxiety on exercise dependence

    PubMed Central

    Cook, Brian; Karr, Trisha M.; Zunker, Christie; Mitchell, James E.; Thompson, Ron; Sherman, Roberta; Erickson, Ann; Cao, Li; Crosby, Ross D.

    2015-01-01

    Background Previous research has identified exercise identity and social physique anxiety as two independent factors that are associated with exercise dependence. Aims The purpose of our study was to investigate the unique and interactive effect of these two known correlates of exercise dependence in a sample of 1,766 female runners. Methods Regression analyses tested the main effects of exercise identity and social physique anxiety on exercise dependence. An interaction term was calculated to examine the potential moderating effect of social physique anxiety on the exercise identity and exercise dependence relationship. Results Results indicate a main effect for exercise identity and social physique anxiety on exercise dependence; and the interaction of these factors explained exercise dependence scores beyond the independent effects. Thus, social physique anxiety acted as a moderator in the exercise identity and exercise dependence relationship. Discussion Our results indicate that individuals who strongly identify themselves as an exerciser and also endorse a high degree of social physique anxiety may be at risk for developing exercise dependence. Conclusions Our study supports previous research which has examined factors that may contribute to the development of exercise dependence and also suggests a previously unknown moderating relationship for social physique anxiety on exercise dependence. PMID:26551910

  9. An Orientation to Explosive Safety.

    ERIC Educational Resources Information Center

    Harris, Betty W.

    1987-01-01

    Provides an overview of various types of explosives. Classifies and describes explosives as initiating or primary explosives, low explosives, and high (secondary explosives). Discusses detonating devices, domestic explosive systems, the sensitivity of explosives, explosive reactions, and emergency responses. (TW)

  10. Reticulation des fibres lignocellulosiques

    NASA Astrophysics Data System (ADS)

    Landrevy, Christel

    Pour faire face à la crise économique la conception de papier à valeur ajoutée est développée par les industries papetières. Le but de se projet est l'amélioration des techniques actuelles de réticulation des fibres lignocellulosiques de la pâte à papier visant à produire un papier plus résistant. En effet, lors des réactions de réticulation traditionnelles, de nombreuses liaisons intra-fibres se forment ce qui affecte négativement l'amélioration anticipée des propriétés physiques du papier ou du matériau produit. Pour éviter la formation de ces liaisons intra-fibres, un greffage sur les fibres de groupements ne pouvant pas réagir entre eux est nécessaire. La réticulation des fibres par une réaction de « click chemistry » appelée cycloaddition de Huisgen entre un azide et un alcyne vrai, catalysée par du cuivre (CuAAC) a été l'une des solutions trouvée pour remédier à ce problème. De plus, une adaptation de cette réaction en milieux aqueux pourrait favoriser son utilisation en milieu industriel. L'étude que nous désirons entreprendre lors de ce projet vise à optimiser la réaction de CuAAC et les réactions intermédiaires (propargylation, tosylation et azidation) sur la pâte kraft, en milieu aqueux. Pour cela, les réactions ont été adaptées en milieu aqueux sur la cellulose microcristalline afin de vérifier sa faisabilité, puis transférée à la pâte kraft et l'influence de différents paramètres comme le temps de réaction ou la quantité de réactifs utilisée a été étudiée. Dans un second temps, une étude des différentes propriétés conférées au papier par les réactions a été réalisée à partir d'une série de tests papetiers optiques et physiques. Mots Clés Click chemistry, Huisgen, CuAAC, propargylation, tosylation, azidation, cellulose, pâte kraft, milieu aqueux, papier.

  11. Nanoengineered explosives

    DOEpatents

    Makowiecki, D.M.

    1996-04-09

    A complex modulated structure is described for reactive elements that have the capability of considerably more heat than organic explosives while generating a working fluid or gas. The explosive and method of fabricating same involves a plurality of very thin, stacked, multilayer structures, each composed of reactive components, such as aluminum, separated from a less reactive element, such as copper oxide, by a separator material, such as carbon. The separator material not only separates the reactive materials, but it reacts therewith when detonated to generate higher temperatures. The various layers of material, thickness of 10 to 10,000 angstroms, can be deposited by magnetron sputter deposition. The explosive detonates and combusts a high velocity generating a gas, such as CO, and high temperatures. 2 figs.

  12. Nanoengineered explosives

    DOEpatents

    Makowiecki, Daniel M.

    1996-01-01

    A complex modulated structure of reactive elements that have the capability of considerably more heat than organic explosives while generating a working fluid or gas. The explosive and method of fabricating same involves a plurality of very thin, stacked, multilayer structures, each composed of reactive components, such as aluminum, separated from a less reactive element, such as copper oxide, by a separator material, such as carbon. The separator material not only separates the reactive materials, but it reacts therewith when detonated to generate higher temperatures. The various layers of material, thickness of 10 to 10,000 angstroms, can be deposited by magnetron sputter deposition. The explosive detonates and combusts a high velocity generating a gas, such as CO, and high temperatures.

  13. Explosive laser

    DOEpatents

    Robinson, C.P.; Jensen, R.J.; Davis, W.C.; Sullivan, J.A.

    1975-09-01

    This patent relates to a laser system wherein reaction products from the detonation of a condensed explosive expand to form a gaseous medium with low translational temperature but high vibration population. Thermal pumping of the upper laser level and de-excitation of the lower laser level occur during the expansion, resulting in a population inversion. The expansion may be free or through a nozzle as in a gas-dynamic configuration. In one preferred embodiment, the explosive is such that its reaction products are CO$sub 2$ and other species that are beneficial or at least benign to CO$sub 2$ lasing. (auth)

  14. Hans Bethe : Des etoiles a la bombe

    NASA Astrophysics Data System (ADS)

    Bonnet-Bidaud, J. M.

    1996-06-01

    Il comprit le premier comment brillent les etoiles. Il fut aussi de cette poignee de scientifiques qui, dans le secret de Los Alamos, mirent au point la tristement celebre bombe atomique. Hans Bethe est l'un des derniers geants qui auront marque la physique de ce siecle d'une empreinte indelebile. C'est dans le bureau 01 du prestigieux laboratoire Kellog de l'institut Caltech qu'il a bien voulu retracer pour nous son impressionnante carriere, et revenir sur les motivations qui ont guide ses pas.

  15. Explosive complexes

    DOEpatents

    Huynh, My Hang V.

    2009-09-22

    Lead-free primary explosives of the formula [M.sup.II(A).sub.R(B.sup.X).sub.S](C.sup.Y).sub.T, where A is 1,5-diaminotetrazole, and syntheses thereof are described. Substantially stoichiometric equivalents of the reactants lead to high yields of pure compositions thereby avoiding dangerous purification steps.

  16. Explosive complexes

    DOEpatents

    Huynh, My Hang V.

    2011-08-16

    Lead-free primary explosives of the formula [M.sup.II(A).sub.R(B.sup.X).sub.S](C.sup.Y).sub.T, where A is 1,5-diaminotetrazole, and syntheses thereof are described. Substantially stoichiometric equivalents of the reactants lead to high yields of pure compositions thereby avoiding dangerous purification steps.

  17. Explosive cord

    NASA Technical Reports Server (NTRS)

    1972-01-01

    Device, jetcord, is metal-clad linear explosive of sufficient flexibility to allow forming into intricate shapes. Total effect is termed ''cutting'' with jetcord consistently ''cutting'' a target of greater thickness than can be penetrated. Applications include sheet metal working, pipe cutting and fire-fighting.

  18. Role of Physique on Probability of Injury to the Neck

    NASA Astrophysics Data System (ADS)

    Shaibani, Saami J.

    2007-03-01

    The primary emphasis in governmental regulation for the prevention and mitigation of automotive trauma tends to be restricted to just a few human surrogates; for example, most Federal Motor Vehicle Safety Standards in the United States involve a 50th-percentile male. This practice is known to conflict with real life, and it can lead to the problem of having safety equipment that is designed to protect some people but can kill or seriously injure others. The influence of physique on neck injury potential is best determined by isolating it as the sole variable in an insult, a constraint satisfied only when there are isokinetic and isogeometric conditions. The latter require there to be pairs of same-vehicle occupants, which are much less common than those relating to the effect of other parameters for impact[1] and environment[2]. Among a possible 60 or so such pairs in the large patient cohort assembled for this study, various subsets were identified as being suitable for detailed research on neck injury and the results of this are reported here. [1] Bull Am Phys Soc, 45, 1018 (2000);[2] Bull Am Phys Soc, 51, 1524 (2006).

  19. Stabilite magnetohydrodynamique des cuves d'electrolyse: Aspects physiques et idees nouvelles

    NASA Astrophysics Data System (ADS)

    Munger, David

    Industrial production of primary aluminum by means of electrolysis of alumina through the Hall--Heroult process raises magnetohydrodynamic (MHD) stability problems in physics. In aluminum reduction cells, a thin layer of electrolytic bath lies on top of a liquid aluminum layer. Magnetic forces acting on the liquids tend to amplify motions of the aluminum--electrolyte interface, thus limiting the process stability and efficiency. We review and comment the established understanding of the MHD of reduction cells, with a particular focus on the metal pad roll instability. Next, we discuss from a physical standpoint a few specific aspects such as the factors that determine the electric current distribution and how a horizontal gradient of the vertical magnetic field affects already known instabilities. We describe the numerical method that we devised to simulate instabilities in reduction cells, and thus uncover a new MHD instability caused by the large eddies generally observed in operating cells. We explain how power supplied by the magnetic force is converted to radial wave motion through the action of centrifugal and Coriolis forces. We finally study different control scenarios for the electrolysis current supplied to the cell by the anodes and thus show that the intensity of the current deflection inside the cell can be considerably reduced by varying the electric potential in such a way as to limit the current fluctuations at the anodes, which allows to slow down the development of MHD instabilities. Keywords. magnetohydrodynamics, waves, instabilities, linearization, numerical simulation, Saint-Venant, magnetostatics, electric current, aluminum reduction.

  20. Explosive Joining

    NASA Technical Reports Server (NTRS)

    1989-01-01

    Laurence J. Bement of Langley Research Center invented a technique to permit metal joining operations under hazardous or inaccessible conditions. The process, which provides a joint with double the strength of the parent metal, involves the use of very small quantities of ribbon explosive to create hermetically sealed joints. When the metal plates are slammed together by the explosion's force, joining is accomplished. The collision causes a skin deep melt and ejection of oxide films on the surfaces, allowing a linkup of electrons that produce superstrong, uniform joints. The technique can be used to join metals that otherwise would not join and offers advantages over mechanical fasteners and adhesives. With Langley assistance, Demex International Ltd. refined and commercialized the technology. Applications include plugging leaking tubes in feedwater heaters. Demex produces the small plugs, associated sleeves and detonators. The technology allows faster plugging, reduces downtime, cuts plugging costs and increases reliability.

  1. Demonstration Explosion

    NASA Astrophysics Data System (ADS)

    Lee, Charles "Skip"

    1998-05-01

    Last week I did a demonstration that produced a serious explosion. After putting methanol in a big glass carboy and rotating the carboy to build up some methanol vapor, I lit the mouth of the carboy. What normally happens is a "jet engine" effect out of the mouth of the carboy. In my case, the carboy exploded. Two polycarbonate blast shields were shattered and glass was blown as far as 15 feet away. I was not seriously cut and bruised, but had I not been using the two blast shields, I would have been severely injured. At this time, I am not sure what caused the explosion. I have done this demonstration around one hundred times with no problem using the exact same amount of methanol and technique. I think it is important to get the word out that this demonstration may be more dangerous than previously thought. I would also welcome any hypotheses concerning what caused the carboy to explode.

  2. Explosive simulants for testing explosive detection systems

    DOEpatents

    Kury, John W.; Anderson, Brian L.

    1999-09-28

    Explosives simulants that include non-explosive components are disclosed that facilitate testing of equipment designed to remotely detect explosives. The simulants are non-explosive, non-hazardous materials that can be safely handled without any significant precautions. The simulants imitate real explosives in terms of mass density, effective atomic number, x-ray transmission properties, and physical form, including moldable plastics and emulsions/gels.

  3. Chaotic explosions

    NASA Astrophysics Data System (ADS)

    Altmann, Eduardo G.; Portela, Jefferson S. E.; Tél, Tamás

    2015-02-01

    We investigate chaotic dynamical systems for which the intensity of trajectories might grow unlimited in time. We show that i) the intensity grows exponentially in time and is distributed spatially according to a fractal measure with an information dimension smaller than that of the phase space, ii) such exploding cases can be described by an operator formalism similar to the one applied to chaotic systems with absorption (decaying intensities), but iii) the invariant quantities characterizing explosion and absorption are typically not directly related to each other, e.g., the decay rate and fractal dimensions of absorbing maps typically differ from the ones computed in the corresponding inverse (exploding) maps. We illustrate our general results through numerical simulation in the cardioid billiard mimicking a lasing optical cavity, and through analytical calculations in the baker map.

  4. Developmental and Contextual Risks of Social Physique Anxiety among Female Athletes

    ERIC Educational Resources Information Center

    Gay, Jennifer L.; Monsma, Eva V.; Torres-McGehee, Toni M.

    2011-01-01

    In the present study, we examined developmental and contextual factors that may increase the odds of reporting higher social physique anxiety (SPA) among 404 adolescent athletes 11 to 16 years old. Findings showed older, later maturing athletes past peak height velocity and with greater body mass index (BMI) reported higher SPA. Individual…

  5. A Polytomous Item Response Theory Analysis of Social Physique Anxiety Scale

    ERIC Educational Resources Information Center

    Fletcher, Richard B.; Crocker, Peter

    2014-01-01

    The present study investigated the social physique anxiety scale's factor structure and item properties using confirmatory factor analysis and item response theory. An additional aim was to identify differences in response patterns between groups (gender). A large sample of high school students aged 11-15 years (N = 1,529) consisting of n =…

  6. Les Annales de Réadaptation et de Médecine Physique publication in 2008.

    PubMed

    Thevenon, A

    2009-03-01

    In 2008 the European Society of Physical and Rehabilitation Medicine (ESPRM) established a network of European journal and promoted collaboration among the European Physical and Rehabilitation Medicine (PRM) journals. In this connection, the authors present here the articles published in the Annales de Réadaptation et Médecine Physique in 2008. In the same time, the European Journal presents in the Annales de Réadaptation et Médecine Physique its main articles of year 2008. The papers published in the Annales de Réadaptation et Médecine Physique in 2008 were reviewed, classified by topics and discussed. Sixty-four papers are described, with a coverage of all the fields of PRM, from childhood to elderly, from basic science to clinical research, from case studies to epidemiological works. The aim of this paper was to provide physiatrists with some articles of the Annales de Réadaptation et Médecine Physique related to their working condition. Next year, the name of our journal will become Annals of Physical and Rehabilitation Medicine, as most of the articles will be published in French and in English, with the hope that more and more European authors and readers will find it more convenient. PMID:19293754

  7. Examining Combinations of Social Physique Anxiety and Motivation Regulations Using Latent Profile Analysis

    ERIC Educational Resources Information Center

    Ullrich-French, Sarah; Cox, Anne E.; Cooper, Brittany Rhoades

    2016-01-01

    Previous research has used cluster analysis to examine how social physique anxiety (SPA) combines with motivation in physical education. This study utilized a more advanced analytic approach, latent profile analysis (LPA), to identify profiles of SPA and motivation regulations. Students in grades 9-12 (N = 298) completed questionnaires at two time…

  8. Effects of Exposure to Physique Slides on the Emotional Responses of Men and Women.

    ERIC Educational Resources Information Center

    Hausenblas, Heather A.; Janelle, Christopher M.; Gardner, Rebecca Ellis; Hagan, Amy L.

    2002-01-01

    Examined high and low body dissatisfied (BD) men's and women's in-task emotional responses to acute exposure to sex-specific physique slides of the aesthetic ideal and of themselves. Participating college students reported their immediate in-task emotional responses to viewing the slides. Men and women, as well as high and low BD groups, reported…

  9. Etude theorique des fluctuations structurales dans les composes organiques a dimensionnalite reduite

    NASA Astrophysics Data System (ADS)

    Dumoulin, Benoit

    Les systemes a dimensionnalite reduite constituent maintenant une branche entiere de la physique de la matiere condensee. Cette derniere s'est developpee rapidement au cours des dernieres annees, avec la decouverte des materiaux organiques qui presentent, justement, des proprietes physiques fortement anisotropes. Cette these presente une etude en trois parties de plusieurs composes organiques qui, bien que tres differents du point de vue de leurs compositions chimiques et de leurs proprietes physiques a haute temperature, subissent tous une instabilite structurale a tres basse temperature. De plus, dans chacun des cas, l'instabilite structurale est precedee d'un important regime fluctuatif a partir duquel les proprietes physiques changent de maniere significative. Notre etude suit un ordre chronologique inverse puisque nous nous attardons en premier lieu au cas de composes recemment decouverts: les composes de la famille des (BCPTTF)2X (X = PF6 , AsF6). Ces derniers sont des isolants magnetiques a la temperature ambiante et subissent une instabilite structurale de type spin-Peierls a une temperature appelee TSP. En particulier, nous nous interessons a l'etude des proprietes physiques de ces systemes dans le regime fluctuatif, qui precede cette instabilite. Notre etude theorique nous permet de comprendre en detail comment ces systemes s'approchent de l'instabilite struturale. Dans la seconde partie de cette these, nous etudions le regime fluctuatif (pre-transitionnel) observe experimentalement dans le compose de (TMTTF)2PF6. Ce compose organique, dont la structure s'apparente aux sels de Bechgaard, subit une instabilite de type spin-Peierls a une temperature T SP = 19K. Bien que ce compose possede la particularite d'etre un bon conducteur a la temperature ambiante, il subit une transition de type Mott-Hubbard a une temperature Trho ≈ 220K et devient alors un isolant magnetique, analogue aux composes de la famille des (BCPTTF)2X. Le regime fluctuatif precedant l

  10. Chromospheric explosions

    NASA Technical Reports Server (NTRS)

    Doschek, G. A.; theory. (3) Resolved: Most chromospheric h; theory. (3) Resolved: Most chromospheric h

    1986-01-01

    Three issues relative to chromospheric explosions were debated. (1) Resolved: The blue-shifted components of x-ray spectral lines are signatures of chromospheric evaporation. It was concluded that the plasma rising with the corona is indeed the primary source of thermal plasma observed in the corona during flares. (2) Resolved: The excess line broading of UV and X-ray lines is accounted for by a convective velocity distribution in evaporation. It is concluded that the hypothesis that convective evaporation produces the observed X-ray line widths in flares is no more than a hypothesis. It is not supported by any self-consistent physical theory. (3) Resolved: Most chromospheric heating is driven by electron beams. Although it is possible to cast doubt on many lines of evidence for electron beams in the chromosphere, a balanced view that debaters on both sides of the question might agree to is that electron beams probably heat the low corona and upper chromosphere, but their direct impact on evaporating the chromosphere is energetically unimportant when compared to conduction. This represents a major departure from the thick-target flare models that were popular before the Workshop.

  11. Extrusion cast explosive

    DOEpatents

    Scribner, Kenneth J.

    1985-01-01

    Improved, multiphase, high performance, high energy, extrusion cast explosive compositions, comprising, a crystalline explosive material; an energetic liquid plasticizer; a urethane prepolymer, comprising a blend of polyvinyl formal, and polycaprolactone; a polyfunctional isocyanate; and a catalyst are disclosed. These new explosive compositions exhibit higher explosive content, a smooth detonation front, excellent stability over long periods of storage, and lower sensitivity to mechanical stimulants.

  12. Optically detonated explosive device

    NASA Technical Reports Server (NTRS)

    Yang, L. C.; Menichelli, V. J. (Inventor)

    1974-01-01

    A technique and apparatus for optically detonating insensitive high explosives, is disclosed. An explosive device is formed by containing high explosive material in a house having a transparent window. A thin metallic film is provided on the interior surface of the window and maintained in contact with the high explosive. A laser pulse provided by a Q-switched laser is focussed on the window to vaporize the metallic film and thereby create a shock wave which detonates the high explosive. Explosive devices may be concurrently or sequentially detonated by employing a fiber optic bundle to transmit the laser pulse to each of the several individual explosive devices.

  13. Ammonium nitrate explosive systems

    SciTech Connect

    Coburn, M.D.; Stinecipher, M.M.

    1981-11-17

    Novel explosives which comprise mixtures of ammonium nitrate and an ammonium salt of a nitroazole in desired ratios are disclosed. A preferred nitroazole is 3,5-dinitro-1,2,4-triazole. The explosive and physical properties of these explosives may readily be varied by the addition of other explosives and oxidizers. Certain of these mixtures have been found to act as ideal explosives.

  14. Ammonium nitrate explosive systems

    DOEpatents

    Stinecipher, Mary M.; Coburn, Michael D.

    1981-01-01

    Novel explosives which comprise mixtures of ammonium nitrate and an ammonium salt of a nitroazole in desired ratios are disclosed. A preferred nitroazole is 3,5-dinitro-1,2,4-triazole. The explosive and physical properties of these explosives may readily be varied by the addition of other explosives and oxidizers. Certain of these mixtures have been found to act as ideal explosives.

  15. Bioremediation of high explosives

    SciTech Connect

    Kitts, C.L.; Alvarez, M.A.; Hanners, J.L.; Ogden, K.L.; Vanderberg-Twary, L.; Unkefer, P.J.

    1995-09-01

    Manufacture and use of high explosives has resulted in contamination of ground water and soils throughout the world. The use of biological methods for remediation of high explosives contamination has received considerable attention in recent years. Biodegradation is most easily studied using organisms in liquid cultures. Thus, the amount of explosive that can be degraded in liquid culture is quite small. However, these experiments are useful for gathering basic information about the biochemical pathways of biodegradation, identifying appropriate organisms and obtaining rates of degradation. The authors` laboratory has investigated all three major areas of explosives bioremediation: explosives in solution, explosives in soil, and the disposal of bulk explosives from demilitarization operations. They investigated the three explosives most commonly used in modern high explosive formulations: 2,4,6-trinitrotoluene (TNT), hexahydro 1,3,5-trinitro-1,3,5-triazine (RDX) and octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX).

  16. Des Vents et des Jets Astrophysiques

    NASA Astrophysics Data System (ADS)

    Sauty, C.

    well expected result from the theory. Although, collimation may be conical, paraboloidal or cylindrical (Part 4), cylindrical collimation is the more likely to occur. The shape of outflows may then be used as a tool to predict physical conditions on the flows or on their source. L'éjection continue de plasma autour d'objets massifs est un phénomène largement répandu en astrophysique, que ce soit sous la forme du vent solaire, de vents stellaires, de jets d'étoiles en formation, de jets stellaires autour d'objets compacts ou de jets extra-galactiques. Cette zoologie diversifiée fait pourtant l'objet d'un commun effort de modélisation. Le but de cette revue est d'abord de présenter qualitativement le développement, depuis leur origine, des diverses théories de vents (Partie 1) et l'inter disciplinarité dans ce domaine. Il s'agit d'une énumération, plus ou moins exhaustive, des idées proposées pour expliquer l'accélération et la morphologie des vents et des jets, accompagnée d'une présentation sommaire des aspects observationnels. Cette partie s'abstient de tout aspect faisant appel au formalisme mathématique. Ces écoulements peuvent être décrits, au moins partiellement, en résolvant les équations magnétohydrodynamiques, axisymétriques et stationnaires. Ce formalisme, à la base de la plupart des théories, est exposé dans la Partie 2. Il permet d'introduire quantitativement les intégrales premières qu'un tel système possède. Ces dernières sont amenées à jouer un rôle important dans la compréhension des phénomènes d'accélération ou de collimation, en particulier le taux de perte de masse, le taux de perte de moment angulaire ou l'énergie du rotateur magnétique. La difficulté de modélisation réside dans l'existence de points critiques, propres aux équations non linéaires, qu'il faut franchir. La nature physique et la localisation de ces points critiques fait l'objet d'un débat important car ils sont la clef de voute de la r

  17. What's in a Surname? Physique, Aptitude, and Sports Type Comparisons between Tailors and Smiths.

    PubMed

    Voracek, Martin; Rieder, Stephan; Stieger, Stefan; Swami, Viren

    2015-01-01

    Combined heredity of surnames and physique, coupled with past marriage patterns and trade-specific physical aptitude and selection factors, may have led to differential assortment of bodily characteristics among present-day men with specific trade-reflecting surnames (Tailor vs. Smith). Two studies reported here were partially consistent with this genetic-social hypothesis, first proposed by Bäumler (1980). Study 1 (N = 224) indicated significantly higher self-rated physical aptitude for prototypically strength-related activities (professions, sports, hobbies) in a random sample of Smiths. The counterpart effect (higher aptitude for dexterity-related activities among Tailors) was directionally correct, but not significant, and Tailor-Smith differences in basic physique variables were nil. Study 2 examined two large total-population-of-interest datasets (Austria/Germany combined, and UK: N = 7001 and 20,532) of men's national high-score lists for track-and-field events requiring different physiques. In both datasets, proportions of Smiths significantly increased from light-stature over medium-stature to heavy-stature sports categories. The predicted counterpart effect (decreasing prevalences of Tailors along these categories) was not supported. Related prior findings, the viability of possible alternative interpretations of the evidence (differential positive selection for trades and occupations, differential endogamy and assortative mating patterns, implicit egotism effects), and directions for further inquiry are discussed in conclusion. PMID:26161803

  18. Impact of the difference in surgical site on the physique in gastrointestinal tract cancer patients

    PubMed Central

    Hara, Tsuyoshi; Kubo, Akira; Kogure, Eisuke; Ishii, Takaya

    2016-01-01

    [Purpose] The purpose of the present study was to observe physical function, physique (only BMI), and nutrition status (evaluated by serum albumin levels) from before surgery to after discharge among perioperative patients with gastrointestinal tract cancer and to examine the effect of difference in surgical site (i.e., stomach, colon, and rectum) in these patients. [Subjects and Methods] The study subjects were 70 patients who underwent surgical treatment for gastrointestinal tract cancer [36 males and 34 females, aged 59.3 ± 11.4 years (mean ± SD)]. The subjects were classified into three levels according to surgical site (stomach, colon, and rectum). We evaluated patients’ physical function, physique, and nutrition status in the three points: before surgery, after surgery, and after discharge. The 6-minute walk distance was measured for physical function. Body mass index was measured for physique. The serum albumin level was measured for nutrition status. [Results] Significant declines in 6-minute walk distance, body mass index, and serum albumin were observed after surgery among the study subjects. In addition, a significant decline in body mass index was observed after discharge compared with before surgery. Regarding body mass index, a significant interaction between surgical site and evaluation times was observed for ANOVA. [Conclusion] These results suggest that BMI after discharge is significantly less than that before surgery and that body mass index changes from before surgery to after surgery are efficacy the difference of surgical site in patients who undergo surgical treatment for gastrointestinal tract cancer. PMID:26957730

  19. What’s in a Surname? Physique, Aptitude, and Sports Type Comparisons between Tailors and Smiths

    PubMed Central

    Voracek, Martin; Rieder, Stephan; Stieger, Stefan; Swami, Viren

    2015-01-01

    Combined heredity of surnames and physique, coupled with past marriage patterns and trade-specific physical aptitude and selection factors, may have led to differential assortment of bodily characteristics among present-day men with specific trade-reflecting surnames (Tailor vs. Smith). Two studies reported here were partially consistent with this genetic-social hypothesis, first proposed by Bäumler (1980). Study 1 (N = 224) indicated significantly higher self-rated physical aptitude for prototypically strength-related activities (professions, sports, hobbies) in a random sample of Smiths. The counterpart effect (higher aptitude for dexterity-related activities among Tailors) was directionally correct, but not significant, and Tailor-Smith differences in basic physique variables were nil. Study 2 examined two large total-population-of-interest datasets (Austria/Germany combined, and UK: N = 7001 and 20532) of men’s national high-score lists for track-and-field events requiring different physiques. In both datasets, proportions of Smiths significantly increased from light-stature over medium-stature to heavy-stature sports categories. The predicted counterpart effect (decreasing prevalences of Tailors along these categories) was not supported. Related prior findings, the viability of possible alternative interpretations of the evidence (differential positive selection for trades and occupations, differential endogamy and assortative mating patterns, implicit egotism effects), and directions for further inquiry are discussed in conclusion. PMID:26161803

  20. Totally confined explosive welding

    NASA Technical Reports Server (NTRS)

    Bement, L. J. (Inventor)

    1978-01-01

    The undesirable by-products of explosive welding are confined and the association noise is reduced by the use of a simple enclosure into which the explosive is placed and in which the explosion occurs. An infrangible enclosure is removably attached to one of the members to be bonded at the point directly opposite the bond area. An explosive is completely confined within the enclosure at a point in close proximity to the member to be bonded and a detonating means is attached to the explosive. The balance of the enclosure, not occupied by explosive, is filled with a shaped material which directs the explosive pressure toward the bond area. A detonator adaptor controls the expansion of the enclosure by the explosive force so that the enclosure at no point experiences a discontinuity in expansion which causes rupture. The use of the technique is practical in the restricted area of a space station.

  1. Extrusion cast explosive

    DOEpatents

    Scribner, K.J.

    1985-11-26

    Disclosed is an improved, multiphase, high performance, high energy, extrusion cast explosive compositions, comprising, a crystalline explosive material; an energetic liquid plasticizer; a urethane prepolymer, comprising a blend of polyvinyl formal, and polycaprolactone; a polyfunctional isocyanate; and a catalyst. These new explosive compositions exhibit higher explosive content, a smooth detonation front, excellent stability over long periods of storage, and lower sensitivity to mechanical stimulants. 1 fig.

  2. Extrusion cast explosive

    DOEpatents

    Scribner, K.J.

    1985-01-29

    Improved, multiphase, high performance, high energy, extrusion cast explosive compositions, comprising, a crystalline explosive material; an energetic liquid plasticizer; a urethane prepolymer, comprising a blend of polyvinyl formal, and polycaprolactone; a polyfunctional isocyanate; and a catalyst are disclosed. These new explosive compositions exhibit higher explosive content, a smooth detonation front, excellent stability over long periods of storage, and lower sensitivity to mechanical stimulants. 1 fig.

  3. Inspection tester for explosives

    DOEpatents

    Haas, Jeffrey S.; Simpson, Randall L.; Satcher, Joe H.

    2007-11-13

    An inspection tester that can be used anywhere as a primary screening tool by non-technical personnel to determine whether a surface contains explosives. It includes a body with a sample pad. First and second explosives detecting reagent holders and dispensers are operatively connected to the body and the sample pad. The first and second explosives detecting reagent holders and dispensers are positioned to deliver the explosives detecting reagents to the sample pad. A is heater operatively connected to the sample pad.

  4. Inspection tester for explosives

    DOEpatents

    Haas, Jeffrey S.; Simpson, Randall L.; Satcher, Joe H.

    2010-10-05

    An inspection tester that can be used anywhere as a primary screening tool by non-technical personnel to determine whether a surface contains explosives. It includes a body with a sample pad. First and second explosives detecting reagent holders and dispensers are operatively connected to the body and the sample pad. The first and second explosives detecting reagent holders and dispensers are positioned to deliver the explosives detecting reagents to the sample pad. A is heater operatively connected to the sample pad.

  5. Hazards of explosives dusts

    NASA Astrophysics Data System (ADS)

    The Bureau of Mines has investigated the hazards of military explosives dispersed as dust clouds in a 20-L test chamber. For purposes of personnel safety, the spark ignitability of the explosives in the form of unconfined dust layers was also studied. The 20-L data show that most of the explosive dusts were capable of sustaining explosions as dust clouds dispersed in air and some dusts were even capable of sustaining explosions when dispersed in nitrogen. The finest sizes of explosive dusts were less reactive than the larger sizes; this is opposite to the particle size effect observed previously for the pure fuel dusts. The data for the explosive dusts were compared to those for pure fuel dusts.

  6. Que peut-on voir avec des neutrons? Une introduction pour des non spécialistes

    NASA Astrophysics Data System (ADS)

    Schweizer, J.

    2005-11-01

    Le neutron est une particule élémentaire qui a été découverte en 1932 par James Chadwick. Ses caractéristiques principales sont résumées dans le tableau I. Il a été utilisé pour la première fois par Clifford Shull en 1946 comme outil pour des expériences de diffusion. Cette technique s'est depuis constamment développée pour concerner tous les aspects de la matière condensée: physique, chimie, matériaux, biologie. Il s'agit d'un outil tout à fait exceptionnel car le neutron possède des propriétés uniques et particulièrement adaptées pour ces études.

  7. New Mix Explosives for Explosive Welding

    NASA Astrophysics Data System (ADS)

    Andreevskikh, Leonid

    2011-06-01

    Suggested and tested were some mix explosives--powder mixtures of a brisant high explosive (HE = RDX, PETN) and an inert diluent (baking soda)--for use in explosive welding. RDX and PETN were selected in view of their high throwing ability and low critical diameter. Since the decomposition of baking soda yields a huge amount of gaseous products, its presence ensures (even at a low HE percentage) a throwing speed that is sufficient for realization of explosive welding, at a reduced brisant action of charge. Mix chargers containing 30-70 wt % HE (the rest baking soda) have been tested experimentally and optimized. For study of possibility to reduce critical diameter of HE mixture, the mixture was prepared where HE crystal sizes did not exceed 10 μm. The tests, which were performed with this HE, revealed that the mixture detonated stably with the velocity D ~ 2 km/s, if the layer thickness was d = 2 mm. The above explosives afford to markedly diminish deformations within the oblique impact zone and thus to carry out explosive welding of hollow items and thin metallic foils.

  8. Regles de fusion en theorie des champs conformes

    NASA Astrophysics Data System (ADS)

    Begin, Luc

    1999-10-01

    Les théories de champs conformes constituent un domaine de recherche très actif avec de nombreuses applications en physique statistique, en matière condensée, en théorie des cordes, en mathématiques, etc. Nous analysons ici le calcul des règles de fusion dans les modèles Wess- Zumino-Witten par des méthodes positives. Les règles de fusion sont des quantités importantes puisqu'elles indiquent comment se combinent les champs primaires de la théorie. L'approche présentée est basée sur l'hypothèse que les règles de fusion sont décrites par un système d'inéquations linéaire et homogène et mène au concept original de «base de fusion». Cette approche simple et générale permet d'utiliser les méthodes combinatoires et de programmation linéaire pour construire les fonctions génératrices et les bases de fusion. Cette méthode permet d'obtenir des résultats originaux et explicites pour les algèbres su (3), su (4) et sp (4).

  9. Explosives tester with heater

    DOEpatents

    Del Eckels, Joel; Nunes, Peter J.; Simpson, Randall L.; Whipple, Richard E.; Carter, J. Chance; Reynolds, John G.

    2010-08-10

    An inspection tester system for testing for explosives. The tester includes a body and a swab unit adapted to be removeably connected to the body. At least one reagent holder and dispenser is operatively connected to the body. The reagent holder and dispenser contains an explosives detecting reagent and is positioned to deliver the explosives detecting reagent to the swab unit. A heater is operatively connected to the body and the swab unit is adapted to be operatively connected to the heater.

  10. Free radical explosive composition

    DOEpatents

    Walker, Franklin E.; Wasley, Richard J.

    1979-01-01

    An improved explosive composition is disclosed and comprises a major portion of an explosive having a detonation velocity between about 1500 and 10,000 meters per second and a minor amount of a getter additive comprising a compound or mixture of compounds capable of capturing or deactivating free radicals or ions under mechanical or electrical shock conditions and which is not an explosive. Exemplary getter additives are isocyanates, olefins and iodine.

  11. Los Alamos explosives performance data

    SciTech Connect

    Mader, C.L.; Crane, S.L.; Johnson, J.N.

    1983-01-01

    This book provides explosives performances, as measured by plate acceleration data, aquarium data, and detonation velocity data. It includes some 800 pages of data and is for explosives scientists more than engineers. (This is a companion volume to the 1980 ''LASL Explosive Property Data'' which covered only pure explosives and well-characterized explosive formulations).

  12. Lung function in children in relation to ethnicity, physique and socioeconomic factors.

    PubMed

    Lum, Sooky; Bountziouka, Vassiliki; Sonnappa, Samatha; Wade, Angie; Cole, Tim J; Harding, Seeromanie; Wells, Jonathan C K; Griffiths, Chris; Treleaven, Philip; Bonner, Rachel; Kirkby, Jane; Lee, Simon; Raywood, Emma; Legg, Sarah; Sears, Dave; Cottam, Philippa; Feyeraband, Colin; Stocks, Janet

    2015-12-01

    Can ethnic differences in spirometry be attributed to differences in physique and socioeconomic factors?Assessments were undertaken in 2171 London primary schoolchildren on two occasions 1 year apart, whenever possible, as part of the Size and Lung function In Children (SLIC) study. Measurements included spirometry, detailed anthropometry, three-dimensional photonic scanning for regional body shape, body composition, information on ethnic ancestry, birth and respiratory history, socioeconomic circumstances, and tobacco smoke exposure.Technically acceptable spirometry was obtained from 1901 children (mean (range) age 8.3 (5.2-11.8) years, 46% boys, 35% White, 29% Black-African origin, 24% South-Asian, 12% Other/mixed) on 2767 test occasions. After adjusting for sex, age and height, forced expiratory volume in 1 s was 1.32, 0.89 and 0.51 z-score units lower in Black-African origin, South-Asian and Other/mixed ethnicity children, respectively, when compared with White children, with similar decrements for forced vital capacity (p<0.001 for all). Although further adjustment for sitting height and chest width reduced differences attributable to ethnicity by up to 16%, significant differences persisted after adjusting for all potential determinants, including socioeconomic circumstances.Ethnic differences in spirometric lung function persist despite adjusting for a wide range of potential determinants, including body physique and socioeconomic circumstances, emphasising the need to use ethnic-specific equations when interpreting results. PMID:26493801

  13. Explosively pumped laser light

    DOEpatents

    Piltch, Martin S.; Michelotti, Roy A.

    1991-01-01

    A single shot laser pumped by detonation of an explosive in a shell casing. The shock wave from detonation of the explosive causes a rare gas to luminesce. The high intensity light from the gas enters a lasing medium, which thereafter outputs a pulse of laser light to disable optical sensors and personnel.

  14. Explosives simulants: Preliminary report

    SciTech Connect

    Moody, G.L.; Pruneda, C.O.; Simpson, R.L.

    1992-03-04

    Two TNT high explosives simulants have been developed. Small scale testing has shown them to be insensitive to: impact, spark, friction, temperature, and shock. The materials have been scaled to 0.5 kg quantities and samples given to the Protective Services Department for field evaluation using explosives detecting canines.

  15. Cell phone explosion.

    PubMed

    Atreya, Alok; Kanchan, Tanuj; Nepal, Samata; Pandey, Bhuwan Raj

    2016-03-01

    Cell phone explosions and resultant burn injuries are rarely reported in the scientific literature. We report a case of cell phone explosion that occurred when a young male was listening to music while the mobile was plugged in for charging. PMID:26427492

  16. Explosively pumped laser light

    SciTech Connect

    Piltch, M.S.; Michelott, R.A.

    1991-09-24

    This patent describes a single shot laser pumped by detonation of an explosive in a shell casing. The shock wave from detonation of the explosive causes a rare gas to luminesce. The high intensity light from the gas enters a lasing medium, which thereafter outputs a pulse of laser light to disable optical sensors and personnel.

  17. Le traitement familial des enfants et des adolescents anorexiques : Des lignes directrices pour le médecin communautaire

    PubMed Central

    Findlay, S; Pinzon, J; Taddeo, D; Katzman, DK

    2010-01-01

    L’anorexie mentale (AM) est une maladie grave qui met la vie en danger et qui fait généralement son apparition pendant l’adolescence. Les données probantes au sujet du traitement optimal de l’AM chez les enfants et les adolescents sont en croissance, mais il reste beaucoup à apprendre. Même si les démarches thérapeutiques actuelles varient au Canada et ailleurs, les données jusqu’à présent indiquent que le traitement familial (TF) est le plus efficace pour les enfants et les adolescents anorexiques. Un élément essentiel du modèle de TF, c’est que les parents sont investis de la responsabilité de rétablir la santé physique de leur enfant et de s’assurer de la reprise complète de son poids. Le médecin qui comprend les principes fondamentaux et la philosophie du TF peut mettre en place les éléments de cette intervention fondée sur des faits probants auprès des jeunes patients anorexiques et de leur famille.

  18. Non-detonable explosive simulators

    DOEpatents

    Simpson, R.L.; Pruneda, C.O.

    1994-11-01

    A simulator which is chemically equivalent to an explosive, but is not detonable. The simulator has particular use in the training of explosives detecting dogs and calibrating sensitive analytical instruments. The explosive simulants may be fabricated by different techniques, a first involves the use of standard slurry coatings to produce a material with a very high binder to explosive ratio without masking the explosive vapor, and the second involves coating inert beads with thin layers of explosive molecules. 5 figs.

  19. Non-detonable explosive simulators

    DOEpatents

    Simpson, Randall L.; Pruneda, Cesar O.

    1994-01-01

    A simulator which is chemically equivalent to an explosive, but is not detonable. The simulator has particular use in the training of explosives detecting dogs and calibrating sensitive analytical instruments. The explosive simulants may be fabricated by different techniques, a first involves the use of standard slurry coatings to produce a material with a very high binder to explosive ratio without masking the explosive vapor, and the second involves coating inert beads with thin layers of explosive molecules.

  20. Research topics in explosives - a look at explosives behaviors

    NASA Astrophysics Data System (ADS)

    Maienschein, J. L.

    2014-05-01

    The behaviors of explosives under many conditions - e.g., sensitivity to inadvertent reactions, explosion, detonation - are controlled by the chemical and physical properties of the explosive materials. Several properties are considered for a range of improvised and conventional explosives. Here I compare these properties across a wide range of explosives to develop an understanding of explosive behaviors. For improvised explosives, which are generally heterogeneous mixtures of ingredients, a range of studies is identified as needed to more fully understand their behavior and properties. For conventional explosives, which are generally comprised of crystalline explosive molecules held together with a binder, I identify key material properties that determine overall sensitivity, including the extremely safe behavior of Insensitive High Explosives, and discuss an approach to predicting the sensitivity or insensitivity of an explosive.

  1. The Social Physique Anxiety Scale: An Example of the Potential Consequence of Negatively Worded Items in Factorial Validity Studies.

    ERIC Educational Resources Information Center

    Motl, Robert W.; Conroy, David E.; Horan, Patrick M.

    2000-01-01

    Used confirmatory factor analysis to examine whether the two-factor solution to the Social Physique Anxiety Scale (E. Hart, M. Leary, and W. Rejeski, 1989) was meaningful. Results for 4 samples of data for college students, high school students, and athletes (n=1,053) from previous studies support the existence of a single substantive factor…

  2. Examining the Moderating Effect of Appearance Impression Motivation on the Relationship between Perceived Physical Appearance and Social Physique Anxiety

    ERIC Educational Resources Information Center

    Amorose, Anthony J.; Hollembeak, Jill

    2005-01-01

    Despite the conceptual importance of impression motivation in predicting social anxiety (Leary & Kowalski, 1995; Schlenker & Leary, 1982), no research has tested the link between impression motivation specifically regarding one's physical appearance (appearance impression motivation, or AIM) and social physique anxiety (SPA). The purpose of this…

  3. Examining the Stability of the 7-Item Social Physique Anxiety Scale Using a Test-Retest Method

    ERIC Educational Resources Information Center

    Scott, Lisa A.; Burke, Kevin L.; Joyner, A. Barry; Brand, Jennifer S.

    2004-01-01

    This study examined the stability of the 7-item Social Physique Anxiety Scale (SPAS-7) using a test-retest method. Collegiate, undergraduate (N = 201) students completed two administrations of the SPAS-7, with a 14-day separation between the administrations. The scale was administered either at the beginning or end of the physical activity class.…

  4. Development of Chinese reference man deformable surface phantom and its application to the influence of physique on electromagnetic dosimetry.

    PubMed

    Yu, D; Wang, M; Liu, Q

    2015-09-01

    A reference man is a theoretical individual that represents the average anatomical structure and physiological and metabolic features of a specific group of people and has been widely used in radiation safety research. With the help of an advantage in deformation, the present work proposed a Chinese reference man adult-male polygon-mesh surface phantom based on the Visible Chinese Human segment image dataset by surface rendering and deforming. To investigate the influence of physique on electromagnetic dosimetry in humans, a series of human phantoms with 10th, 50th and 90th body mass index and body circumference percentile physiques for Chinese adult males were further constructed by deforming the Chinese reference man surface phantom. All the surface phantoms were then voxelized to perform electromagnetic field simulation in a frequency range of 20 MHz to 3 GHz using the finite-difference time-domain method and evaluate the whole-body average and organ average specific absorption rate and the ratios of absorbed energy in skin, fat and muscle to the whole body. The results indicate thinner physique leads to higher WBSAR and the volume of subcutaneous fat, the penetration depth of the electromagnetic field in tissues and standing-wave occurrence may be the influence factors of physique on electromagnetic dosimetry. PMID:26301501

  5. Give or Take a Few? Comparing Measured and Self-Reported Height and Weight as Correlates of Social Physique Anxiety

    ERIC Educational Resources Information Center

    Gay, Jennifer; Monsma, Eva V.; Torres-McGehee, Toni

    2009-01-01

    Statistically controlling for physical size is common practice, especially in self-perception studies uncovering the etiology of maladaptive behaviors, such as eating disorders. For example, social physique anxiety (SPA)--apprehension about social evaluations while presenting oneself in front of others (Leary, 1992)--is a prominent correlate of…

  6. Development of Chinese reference man deformable surface phantom and its application to the influence of physique on electromagnetic dosimetry

    NASA Astrophysics Data System (ADS)

    Yu, D.; Wang, M.; Liu, Q.

    2015-09-01

    A reference man is a theoretical individual that represents the average anatomical structure and physiological and metabolic features of a specific group of people and has been widely used in radiation safety research. With the help of an advantage in deformation, the present work proposed a Chinese reference man adult-male polygon-mesh surface phantom based on the Visible Chinese Human segment image dataset by surface rendering and deforming. To investigate the influence of physique on electromagnetic dosimetry in humans, a series of human phantoms with 10th, 50th and 90th body mass index and body circumference percentile physiques for Chinese adult males were further constructed by deforming the Chinese reference man surface phantom. All the surface phantoms were then voxelized to perform electromagnetic field simulation in a frequency range of 20 MHz to 3 GHz using the finite-difference time-domain method and evaluate the whole-body average and organ average specific absorption rate and the ratios of absorbed energy in skin, fat and muscle to the whole body. The results indicate thinner physique leads to higher WBSAR and the volume of subcutaneous fat, the penetration depth of the electromagnetic field in tissues and standing-wave occurrence may be the influence factors of physique on electromagnetic dosimetry.

  7. Optically measured explosive impulse

    NASA Astrophysics Data System (ADS)

    Biss, Matthew M.; McNesby, Kevin L.

    2014-06-01

    An experimental technique is investigated to optically measure the explosive impulse produced by laboratory-scale spherical charges detonated in air. Explosive impulse has historically been calculated from temporal pressure measurements obtained via piezoelectric transducers. The presented technique instead combines schlieren flow visualization and high-speed digital imaging to optically measure explosive impulse. Prior to an explosive event, schlieren system calibration is performed using known light-ray refractions and resulting digital image intensities. Explosive charges are detonated in the test section of a schlieren system and imaged by a high-speed digital camera in pseudo-streak mode. Spatiotemporal schlieren intensity maps are converted using an Abel deconvolution, Rankine-Hugoniot jump equations, ideal gas law, triangular temperature decay profile, and Schardin's standard photometric technique to yield spatiotemporal pressure maps. Temporal integration of individual pixel pressure profiles over the positive pressure duration of the shock wave yields the explosive impulse generated for a given radial standoff. Calculated explosive impulses are shown to exhibit good agreement between optically derived values and pencil gage pressure transducers.

  8. Lithium niobate explosion monitor

    DOEpatents

    Bundy, C.H.; Graham, R.A.; Kuehn, S.F.; Precit, R.R.; Rogers, M.S.

    1990-01-09

    Monitoring explosive devices is accomplished with a substantially z-cut lithium niobate crystal in abutment with the explosive device. Upon impact by a shock wave from detonation of the explosive device, the crystal emits a current pulse prior to destruction of the crystal. The current pulse is detected by a current viewing transformer and recorded as a function of time in nanoseconds. In order to self-check the crystal, the crystal has a chromium film resistor deposited thereon which may be heated by a current pulse prior to detonation. This generates a charge which is detected by a charge amplifier. 8 figs.

  9. Lithium niobate explosion monitor

    DOEpatents

    Bundy, Charles H.; Graham, Robert A.; Kuehn, Stephen F.; Precit, Richard R.; Rogers, Michael S.

    1990-01-01

    Monitoring explosive devices is accomplished with a substantially z-cut lithium niobate crystal in abutment with the explosive device. Upon impact by a shock wave from detonation of the explosive device, the crystal emits a current pulse prior to destruction of the crystal. The current pulse is detected by a current viewing transformer and recorded as a function of time in nanoseconds. In order to self-check the crystal, the crystal has a chromium film resistor deposited thereon which may be heated by a current pulse prior to detonation. This generates a charge which is detected by a charge amplifier.

  10. Liquid explosives detection

    NASA Astrophysics Data System (ADS)

    Burnett, Lowell J.

    1994-03-01

    A Liquid Explosives Screening System capable of scanning unopened bottles for liquid explosives has been developed. The system can be operated to detect specific explosives directly, or to verify the labeled or bar-coded contents of the container. In this system nuclear magnetic resonance (NMR) is used to interrogate the liquid. NMR produces an extremely rich data set and many parameters of the NMR response can be determined simultaneously. As a result, multiple NMR signatures may be defined for any given set of liquids, and the signature complexity then selected according to the level of threat.

  11. Des Moines.

    ERIC Educational Resources Information Center

    Gore, Deborah, Ed.

    1988-01-01

    This document, intended for elementary students, contains articles and activities designed to acquaint young people with the history of Des Moines, Iowa. The articles are short, and new or difficult words are highlighted and defined for young readers. "The Raccoon River Indian Agency" discusses the archeological exploration of the indian…

  12. Individual variability in the core interthreshold zone as related to body physique, somatotype, and physical constitution.

    PubMed

    Kakitsuba, Naoshi; Mekjavic, Igor B; Katsuura, Tetsuo

    2009-11-01

    For evaluating the effect of body physique, somatotype, and physical constitution on individual variability in the core interthreshold zone (CIZ), data from 22 healthy young Japanese male subjects were examined. The experiment was carried out in a climatic chamber in which air temperature was maintained at 20-24 degrees C. The subjects' body physique and the maximum work load were measured. Somatotype was predicted from the Heath-Carter Somatotype method. In addition, factors reflecting physical constitution, for example, susceptibility to heat and cold, and quality of sleep were obtained by questionnaire. The subjects wore a water-perfused suit which was perfused with water at a temperature of 25 degrees C and at a rate of 600 cc/min, and exercised on an ergometer at 50% of their maximum work rate for 10-15 min until their sweating rate increased. They then remained continuously seated without exercise until shivering increased. Rectal temperature (T(re)) and skin temperatures at four sites were monitored by thermistors, and sweating rate was measured at the forehead with a sweat rate monitor. Oxygen uptake was monitored with a gas analyzer. The results showed individual variability in the CIZ. According to the reciprocal cross-inhibition (RCI) theory, thermoafferent information from peripheral and core sensors is activated by T(re), mean skin temperature (T(sk)), and their changes. Since T(sk) was relatively unchanged, the data were selected to eliminate the influence of the core cooling rate on the sensor-to-effector pathway before RCI, and the relationship between the CIZ and the various factors was then analyzed. The results revealed that susceptibility to heat showed a good correlation with the CIZ, indicating that individual awareness of heat may change the CIZ due to thermoregulatory behavior. PMID:20009375

  13. Explosion suppression system

    DOEpatents

    Sapko, Michael J.; Cortese, Robert A.

    1992-01-01

    An explosion suppression system and triggering apparatus therefor are provided for quenching gas and dust explosions. An electrically actuated suppression mechanism which dispenses an extinguishing agent into the path ahead of the propagating flame is actuated by a triggering device which is light powered. This triggering device is located upstream of the propagating flame and converts light from the flame to an electrical actuation signal. A pressure arming device electrically connects the triggering device to the suppression device only when the explosion is sensed by a further characteristic thereof beside the flame such as the pioneer pressure wave. The light powered triggering device includes a solar panel which is disposed in the path of the explosion and oriented between horizontally downward and vertical. Testing mechanisms are also preferably provided to test the operation of the solar panel and detonator as well as the pressure arming mechanism.

  14. Saturn's Hot Plasma Explosions

    NASA Video Gallery

    This animation based on data obtained by NASA's Cassini Spacecraft shows how the "explosions" of hot plasma on the night side (orange and white) periodically inflate Saturn's magnetic field (white ...

  15. Idaho Explosive Detection System

    SciTech Connect

    Klinger, Jeff

    2011-01-01

    Learn how INL researchers are making the world safer by developing an explosives detection system that can inspect cargo. For more information about INL security research, visit http://www.facebook.com/idahonationallaboratory

  16. Idaho Explosives Detection System

    SciTech Connect

    Edward L. Reber; Larry G. Blackwood; Andrew J. Edwards; J. Keith Jewell; Kenneth W. Rohde; Edward H. Seabury; Jeffery B. Klinger

    2005-12-01

    The Idaho Explosives Detection System was developed at the Idaho National Laboratory (INL) to respond to threats imposed by delivery trucks potentially carrying explosives into military bases. A full-scale prototype system has been built and is currently undergoing testing. The system consists of two racks, one on each side of a subject vehicle. Each rack includes a neutron generator and an array of NaI detectors. The two neutron generators are pulsed and synchronized. A laptop computer controls the entire system. The control software is easily operable by minimally trained staff. The system was developed to detect explosives in a medium size truck within a 5-min measurement time. System performance was successfully demonstrated with explosives at the INL in June 2004 and at Andrews Air Force Base in July 2004.

  17. Modeling nuclear explosion

    NASA Astrophysics Data System (ADS)

    Redd, Jeremy; Panin, Alexander

    2012-10-01

    As a result of the Nuclear Test Ban Treaty, no nuclear explosion tests have been performed by the US since 1992. This appreciably limits valuable experimental data needed for improvement of existing weapons and development of new ones, as well as for use of nuclear devices in non-military applications (such as making underground oil reservoirs or compressed air energy storages). This in turn increases the value of numerical modeling of nuclear explosions and of their effects on the environment. We develop numerical codes simulating fission chain reactions in a supercritical U and Pu core and the dynamics of the subsequent expansion of generated hot plasma in order to better understand the impact of such explosions on their surroundings. The results of our simulations (of both above ground and underground explosions) of various energy yields are presented.

  18. Polymeric binder for explosives

    NASA Technical Reports Server (NTRS)

    Bissell, E. R.

    1972-01-01

    Chemical reaction for producing a polymer which can be mixed with explosives to produce a rigid material is discussed. Physical and chemical properties of polymers are described and chemical structure of the polymer is illustrated.

  19. Idaho Explosive Detection System

    ScienceCinema

    Klinger, Jeff

    2013-05-28

    Learn how INL researchers are making the world safer by developing an explosives detection system that can inspect cargo. For more information about INL security research, visit http://www.facebook.com/idahonationallaboratory

  20. Parametric Explosion Spectral Model

    SciTech Connect

    Ford, S R; Walter, W R

    2012-01-19

    Small underground nuclear explosions need to be confidently detected, identified, and characterized in regions of the world where they have never before occurred. We develop a parametric model of the nuclear explosion seismic source spectrum derived from regional phases that is compatible with earthquake-based geometrical spreading and attenuation. Earthquake spectra are fit with a generalized version of the Brune spectrum, which is a three-parameter model that describes the long-period level, corner-frequency, and spectral slope at high-frequencies. Explosion spectra can be fit with similar spectral models whose parameters are then correlated with near-source geology and containment conditions. We observe a correlation of high gas-porosity (low-strength) with increased spectral slope. The relationship between the parametric equations and the geologic and containment conditions will assist in our physical understanding of the nuclear explosion source.

  1. Chemical Explosion Database

    NASA Astrophysics Data System (ADS)

    Johansson, Peder; Brachet, Nicolas

    2010-05-01

    A database containing information on chemical explosions, recorded and located by the International Data Center (IDC) of the CTBTO, should be established in the IDC prior to entry into force of the CTBT. Nearly all of the large chemical explosions occur in connection with mining activity. As a first step towards the establishment of this database, a survey of presumed mining areas where sufficiently large explosions are conducted has been done. This is dominated by the large coal mining areas like the Powder River (U.S.), Kuznetsk (Russia), Bowen (Australia) and Ekibastuz (Kazakhstan) basins. There are also several other smaller mining areas, in e.g. Scandinavia, Poland, Kazakhstan and Australia, with large enough explosions for detection. Events in the Reviewed Event Bulletin (REB) of the IDC that are located in or close to these mining areas, and which therefore are candidates for inclusion in the database, have been investigated. Comparison with a database of infrasound events has been done as many mining blasts generate strong infrasound signals and therefore also are included in the infrasound database. Currently there are 66 such REB events in 18 mining areas in the infrasound database. On a yearly basis several hundreds of events in mining areas have been recorded and included in the REB. Establishment of the database of chemical explosions requires confirmation and ground truth information from the States Parties regarding these events. For an explosion reported in the REB, the appropriate authority in whose country the explosion occurred is encouraged, on a voluntary basis, to seek out information on the explosion and communicate this information to the IDC.

  2. Explosive Welding and Cladding

    NASA Astrophysics Data System (ADS)

    Meuken, D.; Carton, E. P.

    2004-07-01

    Explosive welding or cladding is usually performed on relative thick plates by means of a large scale parallel plate set-up. At TNO-PML several of the explosive welding configurations that were developed mainly in the nineteen sixties and seventies are being investigated for their potential use in modern industrial applications. Configurations for explosive cladding of curved surfaces such as tubes and rods are also being examined. This can be used to make special bimetallic heat exchanger tubes, or for the protection of electrodes that are used in electrolysis. Explosive line and seam welding are important bonding techniques that allow the welding of both similar and dissimilar metal plates and sheets. Here, bonding occurs over a small overlapping fraction of the two surfaces. This requires only a small amount of explosive (e.g. 5 g/m for line welds in thin ductile sheets). Explosive foil cladding can be used as an alternative coating technique. Plates that are clad with a foil on one or both sides were fabricated in one process step. They can be further machined or deformed using conventional techniques, due to the ductility of the bond and clad material.

  3. Nuclear explosive safety study process

    SciTech Connect

    1997-01-01

    Nuclear explosives by their design and intended use require collocation of high explosives and fissile material. The design agencies are responsible for designing safety into the nuclear explosive and processes involving the nuclear explosive. The methodology for ensuring safety consists of independent review processes that include the national laboratories, Operations Offices, Headquarters, and responsible Area Offices and operating contractors with expertise in nuclear explosive safety. A NES Study is an evaluation of the adequacy of positive measures to minimize the possibility of an inadvertent or deliberate unauthorized nuclear detonation, high explosive detonation or deflagration, fire, or fissile material dispersal from the pit. The Nuclear Explosive Safety Study Group (NESSG) evaluates nuclear explosive operations against the Nuclear Explosive Safety Standards specified in DOE O 452.2 using systematic evaluation techniques. These Safety Standards must be satisfied for nuclear explosive operations.

  4. Non-detonable and non-explosive explosive simulators

    DOEpatents

    Simpson, Randall L.; Pruneda, Cesar O.

    1997-01-01

    A simulator which is chemically equivalent to an explosive, but is not detonable or explodable. The simulator is a combination of an explosive material with an inert material, either in a matrix or as a coating, where the explosive has a high surface ratio but small volume ratio. The simulator has particular use in the training of explosives detecting dogs, calibrating analytical instruments which are sensitive to either vapor or elemental composition, or other applications where the hazards associated with explosives is undesirable but where chemical and/or elemental equivalence is required. The explosive simulants may be fabricated by different techniques. A first method involves the use of standard slurry coatings to produce a material with a very high binder to explosive ratio without masking the explosive vapor, and a second method involves coating inert substrates with thin layers of explosive.

  5. Non-detonable and non-explosive explosive simulators

    DOEpatents

    Simpson, R.L.; Pruneda, C.O.

    1997-07-15

    A simulator which is chemically equivalent to an explosive, but is not detonable or explodable is disclosed. The simulator is a combination of an explosive material with an inert material, either in a matrix or as a coating, where the explosive has a high surface ratio but small volume ratio. The simulator has particular use in the training of explosives detecting dogs, calibrating analytical instruments which are sensitive to either vapor or elemental composition, or other applications where the hazards associated with explosives is undesirable but where chemical and/or elemental equivalence is required. The explosive simulants may be fabricated by different techniques. A first method involves the use of standard slurry coatings to produce a material with a very high binder to explosive ratio without masking the explosive vapor, and a second method involves coating inert substrates with thin layers of explosive. 11 figs.

  6. 49 CFR 172.522 - EXPLOSIVES 1.1, EXPLOSIVES 1.2 and EXPLOSIVES 1.3 placards.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 2 2013-10-01 2013-10-01 false EXPLOSIVES 1.1, EXPLOSIVES 1.2 and EXPLOSIVES 1.3... INFORMATION, TRAINING REQUIREMENTS, AND SECURITY PLANS Placarding § 172.522 EXPLOSIVES 1.1, EXPLOSIVES 1.2 and EXPLOSIVES 1.3 placards. (a) Except for size and color, the EXPLOSIVES 1.1, EXPLOSIVES 1.2 and EXPLOSIVES...

  7. 49 CFR 172.522 - EXPLOSIVES 1.1, EXPLOSIVES 1.2 and EXPLOSIVES 1.3 placards.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 2 2011-10-01 2011-10-01 false EXPLOSIVES 1.1, EXPLOSIVES 1.2 and EXPLOSIVES 1.3... INFORMATION, TRAINING REQUIREMENTS, AND SECURITY PLANS Placarding § 172.522 EXPLOSIVES 1.1, EXPLOSIVES 1.2 and EXPLOSIVES 1.3 placards. (a) Except for size and color, the EXPLOSIVES 1.1, EXPLOSIVES 1.2 and EXPLOSIVES...

  8. 49 CFR 172.522 - EXPLOSIVES 1.1, EXPLOSIVES 1.2 and EXPLOSIVES 1.3 placards.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false EXPLOSIVES 1.1, EXPLOSIVES 1.2 and EXPLOSIVES 1.3... INFORMATION, TRAINING REQUIREMENTS, AND SECURITY PLANS Placarding § 172.522 EXPLOSIVES 1.1, EXPLOSIVES 1.2 and EXPLOSIVES 1.3 placards. (a) Except for size and color, the EXPLOSIVES 1.1, EXPLOSIVES 1.2 and EXPLOSIVES...

  9. 49 CFR 172.522 - EXPLOSIVES 1.1, EXPLOSIVES 1.2 and EXPLOSIVES 1.3 placards.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 2 2014-10-01 2014-10-01 false EXPLOSIVES 1.1, EXPLOSIVES 1.2 and EXPLOSIVES 1.3... INFORMATION, TRAINING REQUIREMENTS, AND SECURITY PLANS Placarding § 172.522 EXPLOSIVES 1.1, EXPLOSIVES 1.2 and EXPLOSIVES 1.3 placards. (a) Except for size and color, the EXPLOSIVES 1.1, EXPLOSIVES 1.2 and EXPLOSIVES...

  10. Explosively separable casing

    DOEpatents

    Jacobson, Albin K.; Rychnovsky, Raymond E.; Visbeck, Cornelius N.

    1985-01-01

    An explosively separable casing including a cylindrical afterbody and a circular cover for one end of the afterbody is disclosed. The afterbody has a cylindrical tongue extending longitudinally from one end which is matingly received in a corresponding groove in the cover. The groove is sized to provide a pocket between the end of the tongue and the remainder of the groove so that an explosive can be located therein. A seal is also provided between the tongue and the groove for sealing the pocket from the atmosphere. A frangible holding device is utilized to hold the cover to the afterbody. When the explosive is ignited, the increase in pressure in the pocket causes the cover to be accelerated away from the afterbody. Preferably, the inner wall of the afterbody is in the same plane as the inner wall of the tongue to provide a maximum space for storage in the afterbody and the side wall of the cover is thicker than the side wall of the afterbody so as to provide a sufficiently strong surrounding portion for the pocket in which the explosion takes place. The detonator for the explosive is also located on the cover and is carried away with the cover during separation. The seal is preferably located at the longitudinal end of the tongue and has a chevron cross section.

  11. Explosion containment device

    DOEpatents

    Benedick, William B.; Daniel, Charles J.

    1977-01-01

    The disclosure relates to an explosives storage container for absorbing and containing the blast, fragments and detonation products from a possible detonation of a contained explosive. The container comprises a layer of distended material having sufficient thickness to convert a portion of the kinetic energy of the explosion into thermal energy therein. A continuous wall of steel sufficiently thick to absorb most of the remaining kinetic energy by stretching and expanding, thereby reducing the momentum of detonation products and high velocity fragments, surrounds the layer of distended material. A crushable layer surrounds the continuous steel wall and accommodates the stretching and expanding thereof, transmitting a moderate load to the outer enclosure. These layers reduce the forces of the explosion and the momentum of the products thereof to zero. The outer enclosure comprises a continuous pressure wall enclosing all of the layers. In one embodiment, detonation of the contained explosive causes the outer enclosure to expand which indicates to a visual observer that a detonation has occurred.

  12. Explosively separable casing

    DOEpatents

    Jacobson, A.K.; Rychnovsky, R.E.; Visbeck, C.N.

    An explosively separable casing including a cylindrical afterbody and a circular cover for one end of the afterbody is disclosed. The afterbody has a cylindrical tongue extending longitudinally from one end which is matingly received in a corresponding groove in the cover. The groove is sized to provide a picket between the end of the tongue and the remainder of the groove so that an explosive can be located therein. A seal is also provided between the tongue and the groove for sealing the pocket from the atmosphere. A frangible holding device is utilized to hold the cover to the afterbody. When the explosive is ignited, the increase in pressure in the pocket causes the cover to be accelerated away from the afterbody. Preferably, the inner wall of the afterbody is in the same plane as the inner wall of the tongue to provide a maximum space for storage in the afterbody and the side wall of the cover is thicker than the side wall of the afterbody so as to provide a sufficiently strong surrounding portion for the pocket in which the explosion takes place. The detonator for the explosive is also located on the cover and is carried away with the cover during separation. The seal is preferably located at the longitudinal end of the tongue and has a chevron cross section.

  13. Novel high explosive compositions

    DOEpatents

    Perry, D.D.; Fein, M.M.; Schoenfelder, C.W.

    1968-04-16

    This is a technique of preparing explosive compositions by the in-situ reaction of polynitroaliphatic compounds with one or more carboranes or carborane derivatives. One or more polynitroaliphatic reactants are combined with one or more carborane reactants in a suitable container and mixed to a homogeneous reaction mixture using a stream of inert gas or conventional mixing means. Ordinarily the container is a fissure, crack, or crevice in which the explosive is to be implanted. The ratio of reactants will determine not only the stoichiometry of the system, but will effect the quality and quantity of combustion products, the explosive force obtained as well as the impact sensitivity. The test values can shift with even relatively slight changes or modifications in the reaction conditions. Eighteen illustrative examples accompany the disclosure. (46 claims)

  14. Destruction of peroxide explosives.

    PubMed

    Oxley, Jimmie C; Smith, James L; Huang, Jiaorong; Luo, Wei

    2009-09-01

    Chemicals containing multiple peroxide functionalities, such as triacetone triperoxide (TATP), diacetone diperoxide (DADP), or hexamethylene triperoxide diamine (HMTD), can be explosive. They are impractical and are not used by legitimate military groups because they are shock and heat sensitive compared to military explosives. They are attractive to terrorists because synthesis is straightforward, requiring only a few easily obtained ingredients. Physical removal of these synthesis products is highly hazardous. This paper discusses methods to degrade peroxide explosives chemically, at room temperature. A number of mixtures containing metals (e.g., zinc, copper) and metal salts (e.g., zinc sulfate, copper chloride) were found effective, some capable of destroying TATP solutions in a few hours. Strong acids proved useful against solid peroxide materials; however, on a 1 g scale, addition of concentrated sulfuric acid caused TATP to detonate. Thus, this technique should only be used to destroy small-laboratory quantities. PMID:19737243

  15. Continuous steam explosion

    SciTech Connect

    Taylor, J.D.; Yu, E.K.C.

    1995-02-01

    StakeTech has focused on developing steam explosion on a commercial basis. The company essentially a biomass conversion company dealing with cellulosic biomass such as wood, crop residues and, more recently, wastepaper and municipal solid waste (MSW). They are faced with a tremendous opportunity to develop uses for the 50% of biomass that is currently wasted. The StakeTech steam explosion process is able to break the bonds using only high-pressure steam with no chemical additives. The continuous StakeTech System now has been installed in five countries and has proved effective in processing a wide variety of raw materials including wood chips, straw, sugarcane bagasse, and waste paper. End-use applications range from specialty chemicals to large-volume agricultural products. The increase of development activities in steam explosion should lead to expanded end-use applications, and acceptance of the technology by industry should accelerate in the years to come.

  16. Explosive synchronization is discontinuous

    NASA Astrophysics Data System (ADS)

    Vlasov, Vladimir; Zou, Yong; Pereira, Tiago

    2015-07-01

    Spontaneous explosive is an abrupt transition to collective behavior taking place in heterogeneous networks when the frequencies of the nodes are positively correlated with the node degree. This explosive transition was conjectured to be discontinuous. Indeed, numerical investigations reveal a hysteresis behavior associated with the transition. Here, we analyze explosive synchronization in star graphs. We show that in the thermodynamic limit the transition to (and out of) collective behavior is indeed discontinuous. The discontinuous nature of the transition is related to the nonlinear behavior of the order parameter, which in the thermodynamic limit exhibits multiple fixed points. Moreover, we unravel the hysteresis behavior in terms of the graph parameters. Our numerical results show that finite-size graphs are well described by our predictions.

  17. Black hole explosions

    NASA Astrophysics Data System (ADS)

    Sciama, D. W.

    A physical account of the processes of black hole explosions is presented. Black holes form when the degeneracy pressure in a neutron star can no longer balance gravitational forces because the mass of the star is too large. Although black holes absorb surrounding matter through the action of a gravitational field, quantum fluctuations have been theoretically demonstrated to occur in the vacuum, and feature a thermal character. The temperature field decreases outwards, in accordance with the nonuniformity of the gravitational field, but does allow thermal radiation, i.e., Hawking radiation, to escape the black hole. The time scale for the radiation shortens as the mass of the black hole decreases, until a time scale is reached which is short enough for the process to be called an explosion. Observations of electron-positron Hawking radiation are suggested to offer proof of a black hole explosion.

  18. Brontides: natural explosive noises.

    PubMed

    Gold, T; Soter, S

    1979-04-27

    Episodes of explosive noises of natural origin, or brontides, have been well documented, often in association with seismic activity and in a few cases as precursors to major earthquakes. Ground-to-air acoustic transmission from shallow earthquakes can account for many of these episodes, but not for all, and other causes, such as the sudden eruption of gas from high-pressure sources in the ground may at times have been responsible. Confusion with distant thunder or artillery at times of anomalous sound propagation complicates the analysis, and more recently the greatly increased frequency of artificial explosive noises and sonic booms has tended to mask the recognition of natural brontides. PMID:17757998

  19. Microcantilever detector for explosives

    DOEpatents

    Thundat, Thomas G.

    1999-01-01

    Methods and apparatus for detecting the presence of explosives by analyzing a vapor sample from the suspect vicinity utilize at least one microcantilever. Explosive gas molecules which have been adsorbed onto the microcantilever are subsequently heated to cause combustion. Heat, along with momentum transfer from combustion, causes bending and a transient resonance response of the microcantilever which may be detected by a laser diode which is focused on the microcantilever and a photodetector which detects deflection of the reflected laser beam caused by heat-induced deflection and resonance response of the microcantilever.

  20. Microcantilever detector for explosives

    DOEpatents

    Thundat, T.G.

    1999-06-29

    Methods and apparatus for detecting the presence of explosives by analyzing a vapor sample from the suspect vicinity utilize at least one microcantilever. Explosive gas molecules which have been adsorbed onto the microcantilever are subsequently heated to cause combustion. Heat, along with momentum transfer from combustion, causes bending and a transient resonance response of the microcantilever which may be detected by a laser diode which is focused on the microcantilever and a photodetector which detects deflection of the reflected laser beam caused by heat-induced deflection and resonance response of the microcantilever. 2 figs.

  1. High-nitrogen explosives

    SciTech Connect

    Naud, D.; Hiskey, M. A.; Kramer, J. F.; Bishop, R. L.; Harry, H. H.; Son, S. F.; Sullivan, G. K.

    2002-01-01

    The syntheses and characterization of various tetrazine and furazan compounds offer a different approach to explosives development. Traditional explosives - such as TNT or RDX - rely on the oxidation of the carbon and hydrogen atoms by the oxygen carrying nitro group to produce the explosive energy. High-nitrogen compounds rely instead on large positive heats of formation for that energy. Some of these high-nitrogen compounds have been shown to be less sensitive to initiation (e.g. by impact) when compared to traditional nitro-containing explosives of similar performances. Using the precursor, 3,6-bis-(3,5-dimethylpyrazol-1-yl)-s-tetrazine (BDT), several useful energetic compounds based on the s-tetrazine system have been synthesized and studied. The compound, 3,3{prime}-azobis(6-amino-s-tetrazine) or DAAT, detonates as a half inch rate stick despite having no oxygen in the molecule. Using perfluoroacetic acid, DAAT can be oxidized to give mixtures of N-oxide isomers (DAAT03.5) with an average oxygen content of about 3.5. This energetic mixture burns at extremely high rates and with low dependency on pressure. Another tetrazine compound of interest is 3,6-diguanidino-s-tetrazine(DGT) and its dinitrate and diperchlorate salts. DGT is easily synthesized by reacting BDT with guanidine in methanol. Using Caro's acid, DGT can be further oxidized to give 3,6-diguanidino-s-tetrazine-1,4-di-N-oxide (DGT-DO). Like DGT, the di-N-oxide can react with nitric acid or perchloric acid to give the dinitrate and the diperchlorate salts. The compounds, 4,4{prime}-diamino-3,3{prime}-azoxyfurazan (DAAF) and 4,4{prime}-diamino-3,3{prime}-azofurazan (DAAzF), may have important future roles in insensitive explosive applications. Neither DAAF nor DAAzF can be initiated by laboratory impact drop tests, yet both have in some aspects better explosive performances than 1,3,5-triamino-2,4,6-trinitrobenzene TATB - the standard of insensitive high explosives. The thermal stability of DAAzF is

  2. Caracterisation du coefficient de retrodiffusion radar des surfaces d'hydrocarbure: Modelisation et interpretation

    NASA Astrophysics Data System (ADS)

    Charbonneau, Francois

    La surveillance maritime est un domaine d'applications ou l'interet politique et scientifique croit constamment au Canada. Un des outils privilegies pour la surveillance maritime est l'acquisition de donnees radars, par des systemes aeroportes ou spatio-portes (ERS-2, RADARSAT et Envisat). Par leur grande couverture spatiale, ainsi que leur sensibilite a la geometrie de surface, les donnees radars permettent, en autres, la detection de cibles ponctuelles (bateaux), estimation des vents, detection des glaces de mer, ainsi que la detection de deversement d'hydrocarbure. Les limites et les avantages de la detection d'hydrocarbure par acquisitions de donnees radars sont bien connus, mais il reste encore des lacunes au niveau de l'extraction des parametres physiques d'une surface d'hydrocarbure. Ce projet a pour objectif de caracteriser le coefficient de retrodiffusion radar associe a une surface d'hydrocarbure en milieu oceanique, par l'introduction d'un modele thermodynamique d'attenuation de la surface, au modele theorique radar IEM. Le modele global permet de simuler le comportement de sigma° en fonction des proprietes visco-elastiques, ainsi que de l'epaisseur de la couche d'hydrocarbure et en fonction des parametres d'acquisition radar. Le modele developpe fut valide a partir des donnees SIR-C acquises lors d'experimentations controlees. A partir des informations environnementales et du type d'hydrocarbure, notre modele a permis d'estime le contraste d'intensite avec une precision de 1 a 1,5 dB, a la bande C. Alors qu'a la bande L, l'erreur sur le contraste est d'environ 1,5 a 2 dB sur l'ensemble des mesures. Ce qui est excellant considerant l'heterogeneite des surfaces analysees. Egalement, nous effectuons des analyses multi-polarisees et polarimetriques avec les donnees SIR-C acquises au-dessus de sites experimentaux. II en ressort que le ratio de polarisation VV/HH, ainsi que le facteur d'anisotropie sont des pistes de recherche prometteuses qu'il faudra

  3. 78 FR 64246 - Commerce in Explosives; List of Explosives Materials

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-10-28

    ... supersedes the List of Explosives Materials dated September 20, 2012 (Docket No. ATF 47N, 77 FR 58410... Department further seeks to clarify that ``black powder substitutes'' are explosives; and have, therefore..., ``Black powder substitutes'' that will appear after ``Black powder based explosive mixtures'' on the...

  4. The combustion of explosives

    SciTech Connect

    Son, S. F.

    2001-01-01

    The safe use of energetic materials has been scientifically studied for over 100 years. Even with this long history of scientific inquiry, the level of understanding of the important deflagration phenomena in accidental initiations of high explosives remains inadequate to predict the response to possible thermal and mechanical (impact) scenarios. The! search also continues for more well behaved explosives and propellants that perform well, yet are insensitive. Once ignition occurs in an explosive, the question then becomes what the resulting violence will be. The classical view is that simple wave propagation proceeds from the ignition point. Recently, several experiments have elucidated the importance of reactive cracks involved in reaction violence in both thermally ignited experiments and impacted explosives, in contrast to classical assumptions, This work presents a viiw of reaction violence, in both thermal and mechanical insults, that argues for the importance of reactive cracks, rather than simple wave propagation processes. Recent work in this area will be reviewed and presented. Initial results involving novel energetic materials will also be discussed.

  5. 75 FR 5545 - Explosives

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-02-03

    ... its Explosives and Blasting Agents Standard at 29 CFR 1910.109 (36 FR 10553-10562). OSHA based the... revisions to the standard (37 FR 6577, 57 FR 6356, and 63 FR 33450). On July 29, 2002, the Institute of... revision (72 FR 18792). On July 17, 2007, however, OSHA closed the comment period, stating that it...

  6. Ecotoxicology of Explosives

    SciTech Connect

    Efroymson, Rebecca Ann; Giffen, Neil R; Morrill, Valerie; Jenkins, Thomas

    2009-04-01

    Managing sites contaminated with munitions constituents is an international challenge. Although the choice of approach and the use of Ecological Risk Assessment (ERA) tools may vary from country to country, the assurance of quality and the direction of ecotoxicological research are universally recognized as shared concerns. Drawing on a multidisciplinary team of contributors, 'Ecotoxicology of Explosives' provides comprehensive and critical reviews available to date on fate, transport, and effects of explosives. The book delineates the state of the science of the ecotoxicology of explosives, past, present, and recently developed. It reviews the accessible fate and ecotoxicological data for energetic materials (EMs) and the methods for their development. The chapters characterize the fate of explosives in the environment, then provide information on their ecological effects in key environmental media, including aquatic, sedimentary, and terrestrial habitats. The book also discusses approaches for assembling these lines of evidence for risk assessment purposes. The chapter authors have critically examined the peer-reviewed literature to identify and prioritize the knowledge gaps and to recommend future areas of research. The editors include a review of the genotoxic effects of the EMs and the cellular and molecular mechanisms underlying the toxicity of these chemicals. They also discuss the transport, transformation, and degradation pathways of these chemicals in the environment that underlie the potential hazardous impact and bioaccumulation of EMs in different terrestrial and aquatic ecological receptors. This information translates into practical applications for the environmental risk assessment of EM-contaminated sites and into recommendations for the sustainable use of defense installations.

  7. Managing the data explosion

    USGS Publications Warehouse

    Hooper, Richard P.; Aulenbach, Brent T.

    1993-01-01

    The 'data explosion' brought on by electronic sensors and automatic samplers can strain the capabilities of existing water-quality data-management systems just when they're needed most to process the information. The U.S. Geological Survey has responded to the problem by setting up an innovative system that allows rapid data analysis.

  8. Portable raman explosives detection

    SciTech Connect

    Moore, David Steven; Scharff, Robert J

    2008-01-01

    Recent advances in portable Raman instruments have dramatically increased their application to emergency response and forensics, as well as homeland defense. This paper reviews the relevant attributes and disadvantages of portable Raman spectroscopy, both essentially and instrumentally, to the task of explosives detection in the field.

  9. Formation et Evolution des Quasars et Contraintes cosmologiques

    NASA Astrophysics Data System (ADS)

    Hatziminaoglou, Evanthia

    2000-06-01

    Cette thèse porte sur l'étude de l'évolution des quasars. Elle en aborde certains aspects théoriques et observationnels, ainsi que la construction des grands échantillons de quasars dans le but à long terme de combiner le tout dans un test cosmologique géométrique pour déterminer les valeurs des paramètres cosmologiques Omega et Lambda. Les paramètres cosmologiques Omegaspan>et Lambdaspan>décrivent la géométrie globale de l'Univers. En faisant des hypothèses raisonnables sur la distribution spatiale et l'évolution des objets astrophysiques (galaxies, amas des galaxies, quasars), on peut déterminer les valeurs de ces paramètres qui sont cohérentes avec ces hypothèses. Les tests cosmologiques traditionnels ont besoin de ''chandelles standards'', objets dont les propriétés intrinsèques sont indépendantes des distances. De tels objets sont probablement fictifs. Néanmoins, certains de ces tests cosmologiques peuvent être adaptés si l'évolution individuelle, ou au moins l'évolution statistique d'une population d'objets est connue. La question de la nature de l'évolution des quasars a très vite été posée et des réponses ''phénoménologiques'' ont d'abord été données. Ces réponses ne faisaient que donner une forme mathématique à l'évolution mais n'expliquaient rien de la physique duphénomène. Les premières tentatives de construction d'un modèle physique, liées au processus d'accrétion sur un trou noir et à la théorie de la formation de l'Univers ont commencé à la fin des années 80. Depuis, des dizaines de modèles tentent d'expliquer les observations, qui sont les résultats de l'étude d'objets de plus en plus nombreux. Au cours de cette thèse, le test V/Vmax a été appliqué sur l'échantillon du Large Bright Quasar Survey en montrant 1) que l'échantillon était biaisé à cause des critères de sélection et 2) que la (simple) loi de Pure Evolution en Luminosité n'était pas une bonne approximation à tout

  10. Influence of metabolic, mechanical and physique variables on middle distance running.

    PubMed

    Brandon, L J; Boileau, R A

    1992-03-01

    The purpose of this study was to determine the variables that most limit middle distance run performance e.g. 800, 1500 and 3000 meters. A predictive research design was employed as 56 runners ran each of the three distances and were evaluated for VO2max, running mechanics, physique variables, ventilatory threshold, and anaerobic capacity and power. The data were analyzed by correlation procedures and stepwise regression analysis. The variables that most limited 1500 and 3000 meter (m) run performance were identical. Maximal oxygen uptake was the most important, but stride length and anaerobic capacity and power also contributed significantly. Run performance at 800 m was influenced by a considerably different set of variables. Peak velocity was most important, but VO2max, % fat and thigh length also contributed significantly. These data indicate that 1500 and 3000 m runners can compete favorably at either distance, while 800 m runners have a different profile and would experience difficulty competing at 1500 and 3000 meters. PMID:1405567

  11. New explosive seam welding concepts

    NASA Technical Reports Server (NTRS)

    Bement, L. J.

    1973-01-01

    Recently developed techniques provide totally-confined linear explosive seam welding and produce scarf joint with linear explosive seam welding. Linear ribbon explosives are utilized in making narrow, continuous, airtight joints in variety of aluminum alloys, titanium, copper, brass, and stainless steel.

  12. Big Explosives Experimental Facility - BEEF

    SciTech Connect

    2014-10-31

    The Big Explosives Experimental Facility or BEEF is a ten acre fenced high explosive testing facility that provides data to support stockpile stewardship and other national security programs. At BEEF conventional high explosives experiments are safely conducted providing sophisticated diagnostics such as high speed optics and x-ray radiography.

  13. Hand held explosives detection system

    DOEpatents

    Conrad, Frank J.

    1992-01-01

    The present invention is directed to a sensitive hand-held explosives detection device capable of detecting the presence of extremely low quantities of high explosives molecules, and which is applicable to sampling vapors from personnel, baggage, cargo, etc., as part of an explosives detection system.

  14. Big Explosives Experimental Facility - BEEF

    ScienceCinema

    None

    2015-01-07

    The Big Explosives Experimental Facility or BEEF is a ten acre fenced high explosive testing facility that provides data to support stockpile stewardship and other national security programs. At BEEF conventional high explosives experiments are safely conducted providing sophisticated diagnostics such as high speed optics and x-ray radiography.

  15. Vapor phase explosions: elementary detonations?

    PubMed

    Fowles, G R

    1979-04-13

    Although liquid-vapor explosions are widely observed, there is no established explanation for their initiation and propagation. Thermodynamics admits the possibility that superheated liquids can support detonations analogous to those that occur in chemical explosives. For liquid methane superheated 50 K above its boiling point at 1 atmosphere, the energy of explosion is 2 to 3 percent of that of TNT. PMID:17738085

  16. Explosive welding of pipes

    NASA Astrophysics Data System (ADS)

    Drennov, O.; Burtseva, O.; Kitin, A.

    2006-08-01

    For connection by welding it is suggested to use the explosive welding method. This method is rather new. Nevertheless, it has become commonly used among the technological developments. This method can be advantageous (saving material and physical resources) comparing to its statical analogs (electron-beam welding, argon-arc welding, plasma welding, gas welding, etc.), in particular, in hard-to-reach areas due to their geographic and climatic conditions. The suggestion is to use water as filler. The principle of non-compressibility of liquid under quasi-dynamic loading is used. In one-dimensional gasdynamic and elastic-plastic calculations we determined non-deformed mass of water. Model experiments with pipes having radii R = 57 mm confirmed results of the calculations and the possibility in principle to weld pipes by explosion with use of water as filler.

  17. Explosive bulk charge

    DOEpatents

    Miller, Jacob Lee

    2015-04-21

    An explosive bulk charge, including: a first contact surface configured to be selectively disposed substantially adjacent to a structure or material; a second end surface configured to selectively receive a detonator; and a curvilinear side surface joining the first contact surface and the second end surface. The first contact surface, the second end surface, and the curvilinear side surface form a bi-truncated hemispherical structure. The first contact surface, the second end surface, and the curvilinear side surface are formed from an explosive material. Optionally, the first contact surface and the second end surface each have a substantially circular shape. Optionally, the first contact surface and the second end surface consist of planar structures that are aligned substantially parallel or slightly tilted with respect to one another. The curvilinear side surface has one of a smooth curved geometry, an elliptical geometry, and a parabolic geometry.

  18. High explosive compound

    DOEpatents

    Crawford, Theodore C.

    1976-01-01

    1. A low detonation velocity explosive consisting essentially of a particulate mixture of ortho-boric acid and trinitrotoluene, said mixture containing from about 25 percent to about 65 percent by weight of ortho-boric acid, said ortho-boric acid comprised of from 60 percent to 90 percent of spherical particles having a mean particle size of about 275 microns and 10 percent to 40 percent of spherical particles having a particle size less than about 44 microns.

  19. [Explosive "Roman find"].

    PubMed

    Stiel, Michael; Dettmeyer, Reinhard; Madea, Burkhard

    2006-01-01

    A case of a 40-year-old hobby archeologist is presented who searched for remains from Roman times. After finding an oblong, cylindrical object, he opened it with a saw to examine it, which triggered an explosion killing the man. The technical investigation of the remains showed that the find was actually a grenade from the 2nd World War. The autopsy findings and the results of the criminological investigation are presented. PMID:16529179

  20. Explosive Welding of Pipes

    NASA Astrophysics Data System (ADS)

    Burtseva, Olga

    2007-06-01

    For connection by welding it is suggested to use the explosive welding method. This method is rather new. Nevertheless, it has become commonly used among the technological developments. This method can be advantageous (saving material and physical resources) comparing to its statical analogs (electron-beam welding, argon-arc welding, plasma welding, gas welding, etc.), in particular, in hard-to-reach areas due to their geographic and climatic conditions. The suggestion is to use water as filler. The principle of non-compressibility of liquid under quasi-dynamic loading is used. In one-dimensional gasdynamic and elastic-plastic calculations we determined non-deformed mass of water (perturbations, which are moving in the axial direction with sound velocity, should not reach the layer end boundaries for 5-7 circulations of shock waves in the radial direction). Linear dimension of the water layer from the zone of pipe coupling along axis in each direction is >= 2R, where R is the internal radius of pipe. Model experiments with pipes having radii R = 57 mm confirmed results of the calculations and the possibility in principle to weld pipes by explosion with use of water as filler. Reduction of pipe diameter after dynamic loading and explosive welding was ˜2%.

  1. Dust cluster explosion

    SciTech Connect

    Saxena, Vikrant; Avinash, K.; Sen, A.

    2012-09-15

    A model for the dust cluster explosion where micron/sub-micron sized particles are accelerated at the expense of plasma thermal energy, in the afterglow phase of a complex plasma discharge is proposed. The model is tested by molecular dynamics simulations of dust particles in a confining potential. The nature of the explosion (caused by switching off the discharge) and the concomitant dust acceleration is found to depend critically on the pressure of the background neutral gas. At low gas pressure, the explosion is due to unshielded Coulomb repulsion between dust particles and yields maximum acceleration, while in the high pressure regime it is due to shielded Yukawa repulsion and yields much feebler acceleration. These results are in agreement with experimental findings. Our simulations also confirm a recently proposed electrostatic (ES) isothermal scaling relation, P{sub E}{proportional_to}V{sub d}{sup -2} (where P{sub E} is the ES pressure of the dust particles and V{sub d} is the confining volume).

  2. Explosives signatures and analysis

    NASA Astrophysics Data System (ADS)

    Fountain, Augustus Way, III; Oyler, Jonathan M.; Ostazeski, Stanley A.

    2008-04-01

    The challenge of sampling explosive materials for various high threat military and civilian operational scenarios requires the community to identify and exploit other chemical compounds within the mixtures that may be available to support stand-off detection techniques. While limited surface and vapor phase characterization of IEDs exist, they are insufficient to guide the future development and evaluation of field deployable explosives detection (proximity and standoff) capabilities. ECBC has conducted a limited investigation of three artillery ammunition types to determine what chemical vapors, if any, are available for sensing; the relative composition of the vapors which includes the more volatile compounds in munitions, i.e., plastersizers and binders; and the sensitivity needed detect these vapors at stand-off. Also in partnership with MIT-Lincoln Laboratory, we performed a background measurement campaign at the National Training Center to determine the baseline ambient amounts and variability of nitrates and nitro-ester compounds as vapors, particulates, and on surfaces; as well as other chemical compounds related to non-energetic explosive additives. Environmental persistence studies in contexts relevant to counter-IED sensing operations, such as surface residues, are still necessary.

  3. Explosive Welding of Pipes

    NASA Astrophysics Data System (ADS)

    Drennov, Oleg; Drennov, Andrey; Burtseva, Olga

    2013-06-01

    For connection by welding it is suggested to use the explosive welding method. This method is rather new. Nevertheless, it has become commonly used among the technological developments. This method can be advantageous (saving material and physical resources) comparing to its statical analogs (electron-beam welding, argon-arc welding, plasma welding, gas welding, etc.), in particular, in hard-to-reach areas due to their geographic and climatic conditions. Explosive welding of cylindrical surfaces is performed by launching of welded layer along longitudinal axis of construction. During this procedure, it is required to provide reliable resistance against radial convergent strains. The traditional method is application of fillers of pipe cavity, which are dense cylindrical objects having special designs. However, when connecting pipes consecutively in pipelines by explosive welding, removal of the fillers becomes difficult and sometimes impossible. The suggestion is to use water as filler. The principle of non-compressibility of liquid under quasi-dynamic loading is used. In one-dimensional gasdynamic and elastic-plastic calculations we determined non-deformed mass of water (perturbations, which are moving in the axial direction with sound velocity, should not reach the layer end boundaries for 5-7 circulations of shock waves in the radial direction). Linear dimension of the water layer from the zone of pipe coupling along axis in each direction is >= 2R, where R is the internal radius of pipe.

  4. Powdery Emulsion Explosive: A New Excellent Industrial Explosive

    NASA Astrophysics Data System (ADS)

    Ni, Ouqi; Zhang, Kaiming; Yu, Zhengquan; Tang, Shujuan

    2012-07-01

    Powdery emulsion explosive (PEE), a new powdery industrial explosive with perfect properties, has been made using an emulsification-spray drying technique. PEE is composed of 91-92.5 wt% ammonium nitrate (AN), 4.5-6 wt% organic fuels, and 1.5-1.8 wt% water. Due to its microstructure as a water-in-oil (W/O) emulsion and low water content, it has excellent detonation performance, outstanding water resistance, reliable safety, and good application compared with other industrial explosives, such as ammonite, emulsion explosives, and ANFO.

  5. Prévalence des cervicalgies et douleurs des membres supérieures chez les utilisateurs d'ordinateur en milieu professionnel à Casablanca (Maroc)

    PubMed Central

    Seknaji, Nawal; Rachidi, Wafaa; Hassoune, Samira; Janani, Saadia; Nani, Samira; Maaroufi, Abderrahmane; Mkinsi, Ouafaa

    2013-01-01

    Introduction Les cervicalgies et douleurs du membre supérieur (CDMS) affectent des millions d'utilisateurs d'ordinateurs dans les pays développés. L'objectif de ce travail était de déterminer la prévalence des cervicalgies et douleurs du membre supérieur (CDMS) à Casablanca et identifier les différents facteurs de risque qui y sont impliqués, afin de définir les sous-groupes à haut risque, et d’établir des plans d'intervention efficaces. Méthodes Il s'agit d'une étude transversale, menée chez 118 employés de bureau francophones et utilisant l'ordinateur, à Casablanca. Les données ont été collectées de Décembre 2011 à Juin 2012, en utilisant la version française d'un questionnaire validé: Maastricht-Upper-extremity-Questionnaire. Résultats 118 utilisateurs d'ordinateur en milieu professionnel ont été recrutés. Parmi les employés enquêtés, 93% ont rapporté des CDMS localisées au moins à un site. Les plaintes les plus fréquemment rapportées étaient les douleurs des épaules et les cervicalgies (48,3% et 46,6% respectivement). Nous n'avons pas remarqué de différence significative des fréquences des douleurs selon le genre. Nos résultats concordent avec les données de la littérature où il existe un certain consensus quant à l'impact des mauvaises conditions ergonomiques sur les troubles musculo-squelettiques du membre supérieur en milieu professionnel. De même, les études récentes examinant les effets combinés et/ou interactifs tant des facteurs biomécaniques/physiques que de facteurs psychosociaux professionnels vont de pair avec nos résultats. Conclusion Il en ressort que les stratégies d'intervention visant à réduire les CDMS doivent agir essentiellement sur 3 volets, le premier correspond à l'amélioration et la sensibilisation quant au respect des conditions ergonomiques, le second concerne l'amélioration des conditions psychosociales. Enfin le troisième volet vise la rationalisant de la demande de

  6. Une recension des écrits concernant la réalité psychoaffective des femmes ayant une vulvodynie : Difficultés rencontrées et stratégies développées

    PubMed Central

    Cantin-Drouin, Maude; Damant, Dominique; Turcotte, Daniel

    2008-01-01

    HISTORIQUE : Au cours des trois dernières décennies, une attention grandissante a été portée à l’étude du syndrome de vulvodynie, soit un inconfort vulvaire chronique inexpliqué, éprouvé en l’absence de pathologie précisée. En plus d’avoir des répercussions physiques, l’expérience de la vulvodynie comporte une dimension psychosociale. OBJECTIF : Cet article vise à faire une recension des écrits sur la réalité psychoaffective des femmes qui éprouvent une vulvodynie. MÉTHODE : Une recherche documentaire basée sur une exploration systématique de textes présentant des résultats de recherche et recensés dans les principales banques de données en sciences sociales, dont Dissertation Abstracts, Current Contents et PsycINFO, a été réalisée. RÉSULTATS : Cette recension des écrits révèle, malgré la présence de certains résultats divergents, que les femmes ayant une vulvodynie affrontent souvent des difficultés identitaires et psychologiques, qui sont influencées notamment par les normes sociales de sexualité et de féminité. Pour composer avec ces difficultés, les femmes développent différentes stratégies visant à diminuer le stress occasionné par la douleur et à améliorer leur bien-être psychologique. CONCLUSION : Les difficultés relationnelles et psychologiques vécues par les femmes ayant une vulvodynie ne découlent pas seulement de la douleur physique, mais aussi du sens qu’elles lui accordent, souvent influencé par les discours sociaux sur l’hétérosexualité et la féminité. Il importe donc d’intervenir auprès des femmes en tenant compte de l’influence du contexte social tout en poursuivant le développement des connaissances sur les aspects psychosociaux de cette expérience. PMID:18592063

  7. Explosive turbulent magnetic reconnection.

    PubMed

    Higashimori, K; Yokoi, N; Hoshino, M

    2013-06-21

    We report simulation results for turbulent magnetic reconnection obtained using a newly developed Reynolds-averaged magnetohydrodynamics model. We find that the initial Harris current sheet develops in three ways, depending on the strength of turbulence: laminar reconnection, turbulent reconnection, and turbulent diffusion. The turbulent reconnection explosively converts the magnetic field energy into both kinetic and thermal energy of plasmas, and generates open fast reconnection jets. This fast turbulent reconnection is achieved by the localization of turbulent diffusion. Additionally, localized structure forms through the interaction of the mean field and turbulence. PMID:23829741

  8. Explosions on the Sun

    NASA Astrophysics Data System (ADS)

    Harra, Louise K.

    2005-10-01

    I describe two of the most dynamic and highly energetic phenomena in the Solar System - these are the eruptions and flaring that occur on the Sun. They can release as much energy as 10 million volcanoes, and throw out material into the solar system with similar mass to Mount Everest! The theories of what can produce such an explosion are based around the magnetic field that confines the gas. These events can produce emission right across the electromagnetic spectrum. The status of our ability to predict these events is discussed.

  9. Gasdynamics of explosions today.

    NASA Technical Reports Server (NTRS)

    Brode, H. L.; Glass, I. I.; Oppenheim, A. K.

    1971-01-01

    A brief review is given of blast and detonation wave phenomena and some of their uses in war and peace. It is concluded that great strides have been made over the last three decades toward the physical understanding, the analytical-numerical solution, and the measurement of dynamic and thermodynamic quantities, also taking into consideration severe environments and extremely short durations. Questions of internal ballistics are discussed together with hypervelocity launchers and shock tubes, collapsing cylindrical drivers, spherical implosions, explosive weapons, dynamic response, and equation of state data.

  10. Des recommandations probantes pour surveiller l’innocuité des antipsychotiques de deuxième génération chez les enfants et les adolescents

    PubMed Central

    Pringsheim, Tamara; Panagiotopoulos, Constadina; Davidson, Jana; Ho, Josephine

    2012-01-01

    HISTORIQUE : Au Canada, l’utilisation d’antipsychotiques, notamment les antipsychotiques de deuxième génération (ADG), a augmenté de façon considérable depuis cinq ans chez les enfants ayant des troubles de santé mentale. Ces médicaments ont le potentiel de causer de graves complications métaboliques et neurologiques lorsqu’on les utilise de manière chronique. OBJECTIF : Synthétiser les données probantes relatives aux effets secondaires métaboliques et neurologiques précis associés à l’usage d’ADG chez les enfants et fournir des recommandations probantes sur la surveillance de ces effets secondaires. MÉTHODOLOGIE : Les auteurs ont procédé à une analyse systématique des essais cliniques contrôlés des ADG auprès d’enfants. Ils ont fait des recommandations à l’égard de la surveillance de l’innocuité des ADG d’après un modèle de classification fondé sur le système GRADE (système de notation de l’évaluation et de l’élaboration des recommandations). Lorsque les données probantes n’étaient pas suffisantes, ils fondaient leurs recommandations sur le consensus et l’avis d’experts. Un groupe consensuel multidisciplinaire a analysé toutes les données probantes pertinentes et est parvenu à un consensus à l’égard des recommandations. RÉSULTATS : Les recommandations probantes portant sur la surveillance de l’innocuité des ADG figurent dans les présentes lignes directrices. Les auteurs indiquent la qualité des recommandations relatives à des examens physiques et tests de laboratoire précis à l’égard de chaque ADG à des moments déterminés. CONCLUSION : De multiples essais aléatoires et contrôlés ont permis d’évaluer l’efficacité de bon nombre des ADG utilisés pour traiter les troubles de santé mentale en pédiatrie. Toutefois, leurs avantages ne sont pas sans risques : on observe à la fois des effets secondaires métaboliques et neurologiques chez les enfants traités au moyen d

  11. Introduction to gasdynamics of explosions

    NASA Technical Reports Server (NTRS)

    Oppenheim, A. K.

    1973-01-01

    Questions concerning the genesis and sustenance of an explosion are investigated, giving attention to the mechanics of explosions, the gasdynamics of explosions, aspects of technological significance, and future prospects. The dynamics of exothermic processes is discussed together with the most prominent effects of explosions. Blast waves are considered, taking into account conservation principles, blast wave transformation, conservative equations in nondimensional form, the equation of state, Eulerian space profiles, Eulerian time profiles, Lagrangian time profiles, boundary conditions and integral relations, and self-similar flow fields.

  12. Low voltage nonprimary explosive detonator

    DOEpatents

    Dinegar, Robert H.; Kirkham, John

    1982-01-01

    A low voltage, electrically actuated, nonprimary explosive detonator is disclosed wherein said detonation is achieved by means of an explosive train in which a deflagration-to-detonation transition is made to occur. The explosive train is confined within a cylindrical body and positioned adjacent to low voltage ignition means have electrical leads extending outwardly from the cylindrical confining body. Application of a low voltage current to the electrical leads ignites a self-sustained deflagration in a donor portion of the explosive train which then is made to undergo a transition to detonation further down the train.

  13. Explosive scabbling of structural materials

    DOEpatents

    Bickes, Jr., Robert W.; Bonzon, Lloyd L.

    2002-01-01

    A new approach to scabbling of surfaces of structural materials is disclosed. A layer of mildly energetic explosive composition is applied to the surface to be scabbled. The explosive composition is then detonated, rubbleizing the surface. Explosive compositions used must sustain a detonation front along the surface to which it is applied and conform closely to the surface being scabbled. Suitable explosive compositions exist which are stable under handling, easy to apply, easy to transport, have limited toxicity, and can be reliably detonated using conventional techniques.

  14. Zirconium hydride containing explosive composition

    DOEpatents

    Walker, Franklin E.; Wasley, Richard J.

    1981-01-01

    An improved explosive composition is disclosed and comprises a major portion of an explosive having a detonation velocity between about 1500 and 10,000 meters per second and a minor amount of a donor additive comprising a non-explosive compound or mixture of non-explosive compounds which when subjected to an energy fluence of 1000 calories/cm.sup.2 or less is capable of releasing free radicals each having a molecular weight between 1 and 120. Exemplary donor additives are dibasic acids, polyamines and metal hydrides.

  15. Neutrino Leakage and Supernova Explosion

    NASA Astrophysics Data System (ADS)

    Liao, Dao-Bing; Zhang, Miao-Jing; Li, Yan; Pan, Jiang-Hong; Chen, Xiu

    2015-04-01

    In the process of supernova explosion the leakage of neutrinos is very important. Adopting an one-dimensional spherically symmetrical model, and under the different neutrino leakage modes, the explosion processes of type II supernovae with masses of 12 M⊙, 14 M⊙, and 15 M⊙ are simulated numerically. The results indicate that all these different neutrino leakage modes have influences on the supernova collapse, shock propagation, and supernova explosion. The best values of the related parameters which are propitious for the type II supernova explosion are given. In addition, the impacts of the equation of state and the compression modulus on the simulated results are discussed.

  16. What factors control the superficial lava dome explosivity?

    NASA Astrophysics Data System (ADS)

    Boudon, Georges; Balcone-Boissard, Hélène; Villemant, Benoit; Morgan, Daniel J.

    2015-04-01

    Dome-forming eruption is a frequent eruptive style; lava domes result from intermittent, slow extrusion of viscous lava. Most dome-forming eruptions produce highly microcrystallized and highly- to almost totally-degassed magmas which have a low explosive potential. During lava dome growth, recurrent collapses of unstable parts are the main destructive process of the lava dome, generating concentrated pyroclastic density currents (C-PDC) channelized in valleys. These C-PDC have a high, but localized, damage potential that largely depends on the collapsed volume. Sometimes, a dilute ash cloud surge develops at the top of the concentrated flow with an increased destructive effect because it may overflow ridges and affect larger areas. In some cases, large lava dome collapses can induce a depressurization of the magma within the conduit, leading to vulcanian explosions. By contrast, violent, laterally directed, explosions may occur at the base of a growing lava dome: this activity generates dilute and turbulent, highly-destructive, pyroclastic density currents (D-PDC), with a high velocity and propagation poorly dependent on the topography. Numerous studies on lava dome behaviors exist, but the triggering of lava dome explosions is poorly understood. Here, seven dome-forming eruptions are investigated: in the Lesser Antilles arc: Montagne Pelée, Martinique (1902-1905, 1929-1932 and 650 y. BP eruptions), Soufrière Hills, Montserrat; in Guatemala, Santiaguito (1929 eruption); in La Chaîne des Puys, France (Puy de Dome and Puy Chopine eruptions). We propose a new model of superficial lava-dome explosivity based upon a textural and geochemical study (vesicularity, microcrystallinity, cristobalite distribution, residual water contents, crystal transit times) of clasts produced by these key eruptions. Superficial explosion of a growing lava dome may be promoted through porosity reduction caused by both vesicle flattening due to gas escape and syn-eruptive cristobalite

  17. Controlled by Distant Explosions

    NASA Astrophysics Data System (ADS)

    2007-03-01

    VLT Automatically Takes Detailed Spectra of Gamma-Ray Burst Afterglows Only Minutes After Discovery A time-series of high-resolution spectra in the optical and ultraviolet has twice been obtained just a few minutes after the detection of a gamma-ray bust explosion in a distant galaxy. The international team of astronomers responsible for these observations derived new conclusive evidence about the nature of the surroundings of these powerful explosions linked to the death of massive stars. At 11:08 pm on 17 April 2006, an alarm rang in the Control Room of ESO's Very Large Telescope on Paranal, Chile. Fortunately, it did not announce any catastrophe on the mountain, nor with one of the world's largest telescopes. Instead, it signalled the doom of a massive star, 9.3 billion light-years away, whose final scream of agony - a powerful burst of gamma rays - had been recorded by the Swift satellite only two minutes earlier. The alarm was triggered by the activation of the VLT Rapid Response Mode, a novel system that allows for robotic observations without any human intervention, except for the alignment of the spectrograph slit. ESO PR Photo 17a/07 ESO PR Photo 17a/07 Triggered by an Explosion Starting less than 10 minutes after the Swift detection, a series of spectra of increasing integration times (3, 5, 10, 20, 40 and 80 minutes) were taken with the Ultraviolet and Visual Echelle Spectrograph (UVES), mounted on Kueyen, the second Unit Telescope of the VLT. "With the Rapid Response Mode, the VLT is directly controlled by a distant explosion," said ESO astronomer Paul Vreeswijk, who requested the observations and is lead-author of the paper reporting the results. "All I really had to do, once I was informed of the gamma-ray burst detection, was to phone the staff astronomers at the Paranal Observatory, Stefano Bagnulo and Stan Stefl, to check that everything was fine." The first spectrum of this time series was the quickest ever taken of a gamma-ray burst afterglow

  18. Tenderizing Meat with Explosives

    NASA Astrophysics Data System (ADS)

    Gustavson, Paul K.; Lee, Richard J.; Chambers, George P.; Solomon, Morse B.; Berry, Brad W.

    2001-06-01

    Investigators at the Food Technology and Safety Laboratory have had success tenderizing meat by explosively shock loading samples submerged in water. This technique, referred to as the Hydrodynamic Pressure (HDP) Process, is being developed to improve the efficiency and reproducibility of the beef tenderization processing over conventional aging techniques. Once optimized, the process should overcome variability in tenderization currently plaguing the beef industry. Additional benefits include marketing lower quality grades of meat, which have not been commercially viable due to a low propensity to tenderization. The simplest and most successful arrangement of these tests has meat samples (50 to 75 mm thick) placed on a steel plate at the bottom of a plastic water vessel. Reported here are tests which were instrumented by Indian Head investigators. Carbon-composite resistor-gauges were used to quantify the shock profile delivered to the surface of the meat. PVDF and resistor gauges (used later in lieu of PVDF) provided data on the pressure-time history at the meat/steel interface. Resulting changes in tenderization were correlated with increasing shock duration, which were provided by various explosives.

  19. Explosive cyclogenesis program planned

    NASA Astrophysics Data System (ADS)

    Hadlock, Ron

    A research program to study explosive cyclogenesis of Atlantic winter storms is being planned by the Office of Naval Research (ONR; Washington, D.C.) and a team of investigators from universities and other meteorological and oceanographic institutions. The goals of the Experiment on Rapidly Intensifying Cyclones in the Atlantic (ERICA) are to develop an understanding of the fundamental physical processes in the atmosphere that lead to explosive cyclogenesis at sea,to identify measurable precursors that can be used for accurate operational dynamical meteorological forecast model predictions, andto determine the minimum set of these observations that is necessary for accurate forecasts of intense cyclogenesis at sea.The multiyear program efforts, including numerical modeling research, will benefit from the related Genesis of Atlantic Lows Experiment (GALE) and Canadian Atlantic Storms Program (CASP) field measurement episodes, which were recently completed (January-March 1986). ERICA's phase of intensive measurements in the field is scheduled for January-March 1989 in the North Atlantic, centered at approximately 40°N and 60°W.

  20. Laser machining of explosives

    DOEpatents

    Perry, Michael D.; Stuart, Brent C.; Banks, Paul S.; Myers, Booth R.; Sefcik, Joseph A.

    2000-01-01

    The invention consists of a method for machining (cutting, drilling, sculpting) of explosives (e.g., TNT, TATB, PETN, RDX, etc.). By using pulses of a duration in the range of 5 femtoseconds to 50 picoseconds, extremely precise and rapid machining can be achieved with essentially no heat or shock affected zone. In this method, material is removed by a nonthermal mechanism. A combination of multiphoton and collisional ionization creates a critical density plasma in a time scale much shorter than electron kinetic energy is transferred to the lattice. The resulting plasma is far from thermal equilibrium. The material is in essence converted from its initial solid-state directly into a fully ionized plasma on a time scale too short for thermal equilibrium to be established with the lattice. As a result, there is negligible heat conduction beyond the region removed resulting in negligible thermal stress or shock to the material beyond a few microns from the laser machined surface. Hydrodynamic expansion of the plasma eliminates the need for any ancillary techniques to remove material and produces extremely high quality machined surfaces. There is no detonation or deflagration of the explosive in the process and the material which is removed is rendered inert.

  1. Explosive components facility certification tests

    SciTech Connect

    Dorrell, L.; Johnson, D.

    1995-08-01

    Sandia National Laboratories has recently completed construction of a new Explosive Components Facility (ECF) that will be used for the research and development of advanced explosives technology. The ECF includes nine indoor firing pads for detonating explosives and monitoring the detonations. Department of Energy requirements for certification of this facility include detonation of explosive levels up to 125 percent of the rated firing pad capacity with no visual structural degradation resulting from the explosion. The Explosives Projects and Diagnostics Department at Sandia decided to expand this certification process to include vibration and acoustic monitoring at various locations throughout the building during these explosive events. This information could then be used to help determine the best locations for noise and vibration sensitive equipment (e.g. scanning electron microscopes) used for analysis throughout the building. This facility has many unique isolation features built into the explosive chamber and laboratory areas of the building that allow normal operation of other building activities during explosive tests. This paper discusses the design of this facility and the various types of explosive testing performed by the Explosives Projects and Diagnostics Department at Sandia. However, the primary focus of the paper is directed at the vibration and acoustic data acquired during the certification process. This includes the vibration test setup and data acquisition parameters, as well as analysis methods used for generating peak acceleration levels and spectral information. Concerns over instrumentation issues such as the choice of transducers (appropriate ranges, resonant frequencies, etc.) and measurements with long cable lengths (500 feet) are also discussed.

  2. Des proprietes de l'etat normal du modele de Hubbard bidimensionnel

    NASA Astrophysics Data System (ADS)

    Lemay, Francois

    Depuis leur decouverte, les etudes experimentales ont demontre que les supra-conducteurs a haute temperature ont une phase normale tres etrange. Les proprietes de ces materiaux ne sont pas bien decrites par la theorie du liquide de Fermi. Le modele de Hubbard bidimensionnel, bien qu'il ne soit pas encore resolu, est toujours considere comme un candidat pour expliquer la physique de ces composes. Dans cet ouvrage, nous mettons en evidence plusieurs proprietes electroniques du modele qui sont incompatibles avec l'existence de quasi-particules. Nous montrons notamment que la susceptibilite des electrons libres sur reseau contient des singularites logarithmiques qui influencent de facon determinante les proprietes de la self-energie a basse frequence. Ces singularites sont responsables de la destruction des quasi-particules. En l'absence de fluctuations antiferromagnetiques, elles sont aussi responsables de l'existence d'un petit pseudogap dans le poids spectral au niveau de Fermi. Les proprietes du modele sont egalement etudiees pour une surface de Fermi similaire a celle des supraconducteurs a haute temperature. Un parallele est etabli entre certaines caracteristiques du modele et celles de ces materiaux.

  3. Lidar Detection of Explosives Traces

    NASA Astrophysics Data System (ADS)

    Bobrovnikov, Sergei M.; Gorlov, Evgeny V.; Zharkov, Victor I.; Panchenko, Yury N.

    2016-06-01

    The possibility of remote detection of traces of explosives using laser fragmentation/laser-induced fluorescence (LF/LIF) is studied. Experimental data on the remote visualization of traces of trinitrotoluene (TNT), hexogen (RDX), trotyl-hexogen (Comp B), octogen (HMX), and tetryl with a scanning lidar detector of traces of nitrogen-containing explosives at a distance of 5 m are presented.

  4. Les perceptions des femmes tunisiennes selon le modèle des croyances liées à la santé et leurs pratiques relativement à l'ostéoporose

    PubMed Central

    Belgacem, Amina; Nouira, Amel; Soussi, Sonia

    2016-01-01

    Introduction L'étude a pour objectif de décrire les croyances des femmes et leurs pratiques liées à la santé et à l'ostéoporose, afin d'élaborer des interventions efficaces et ciblées pour la prévention de cette maladie dans le contexte tunisien. Méthodes Une étude descriptive transversale a été effectuée auprès de 100 femmes tunisiennes, âgées de 45 ans et plus, qui consultent au centre de santé de base d'une zone périurbaine de la région de Sousse (Tunisie). La collecte de l'information a été réalisée à l'aide de « l'échelle des croyances relatives à la santé sur l'ostéoporose» développée par Kim et ses collègues traduit en arabe et validé en Tunisie et le questionnaire de «Calcul des apports calciques quotidiens» développé par Fardellone Patrice. L'interprétation des résultants s'est basée sur le «Health Belief Model ». Résultats La perception des participantes pourrait être considérée comme au dessus de la moyenne pour la vulnérabilité de l'ostéoporose (58%), la gravité de la maladie, les avantages de la pratique de l'activité physique, les avantages de l'apport en calcium et la motivation à la santé; par contre, elle pourrait être considérée comme modérée concernant les obstacles à la prévention. Cependant, les pratiques exposant au risque de la maladie sont relativement fréquentes et ceci essentiellement en rapport avec des facteurs socio-économiques et culturels. Conclusion Les programmes de promotion doivent viser la création d'un environnement physique et social favorable à l'adoption des comportements à moindre risque et viser l'éducation ciblée de la population. PMID:27217868

  5. The Scaled Thermal Explosion Experiment

    SciTech Connect

    Wardell, J F; Maienschein, J L

    2002-07-05

    We have developed the Scaled Thermal Explosion Experiment (STEX) to provide a database of reaction violence from thermal explosion for explosives of interest. Such data are needed to develop, calibrate, and validate predictive capability for thermal explosions using simulation computer codes. A cylinder of explosive 25, 50 or 100 mm in diameter, is confined in a steel cylinder with heavy end caps, and heated under controlled conditions until reaction. Reaction violence is quantified through non-contact micropower impulse radar measurements of the cylinder wall velocity and by strain gauge data at reaction onset. Here we describe the test concept, design and diagnostic recording, and report results with HMX- and RDX-based energetic materials.

  6. Trace Explosive Detection Using Nanosensors

    SciTech Connect

    Senesac, Larry R; Thundat, Thomas George

    2008-01-01

    Selective and sensitive detection of explosives is very important in countering terrorist threats. Detecting trace explosives has become a very complex and expensive endeavor because of a number of factors, such as the wide variety of materials that can be used as explosives, the lack of easily detectable signatures, the vast number of avenues by which these weapons can be deployed, and the lack of inexpensive sensors with high sensitivity and selectivity. High sensitivity and selectivity, combined with the ability to lower the deployment cost of sensors using mass production, is essential in winning the war on explosives-based terrorism. Nanosensors have the potential to satisfy all the requirements for an effective platform for the trace detection of explosives.

  7. Mixing in explosions

    SciTech Connect

    Kuhl, A.L.

    1993-12-01

    Explosions always contain embedded turbulent mixing regions, for example: boundary layers, shear layers, wall jets, and unstable interfaces. Described here is one particular example of the latter, namely, the turbulent mixing occurring in the fireball of an HE-driven blast wave. The evolution of the turbulent mixing was studied via two-dimensional numerical simulations of the convective mixing processes on an adaptive mesh. Vorticity was generated on the fireball interface by baroclinic effects. The interface was unstable, and rapidly evolved into a turbulent mixing layer. Four phases of mixing were observed: (1) a strong blast wave phase; (2) and implosion phase; (3) a reshocking phase; and (4) an asymptotic mixing phase. The flowfield was azimuthally averaged to evaluate the mean and r.m.s. fluctuation profiles across the mixing layer. The vorticity decayed due to a cascade process. This caused the corresponding enstrophy parameter to increase linearly with time -- in agreement with homogeneous turbulence calculations of G.K. Batchelor.

  8. The Interaction of Explosively Generated Plasma with Explosives

    NASA Astrophysics Data System (ADS)

    Tasker, Douglas; LANL Team

    2015-06-01

    It has been shown that the temperature of explosively generated plasma (EGP) is of the order of 1 eV and plasma ejecta can be focused to achieve velocities as high as 25 km/s. These high velocity plasma can readily penetrate a wide range of materials including metals. Proof-of-principle tests were performed to determine if EGP could be used for explosive ordnance demolition and other applications. The test goals were: to benignly disable ordnance containing relatively sensitive high performance explosives (PBX-9501); and to investigate the possibility of interrupting an ongoing detonation in a powerful high explosive (again PBX-9501) with EGP. Experiments were performed to establish the optimum sizes of plasma generators for the benign deactivation of high explosives, i.e., the destruction of the ordnance without initiating a detonation or comparable violent event. These experiments were followed by attempts to interrupt an ongoing detonation by the destruction of the unreacted explosive in its path. The results were encouraging. First, it was demonstrated that high explosives could be destroyed without the initiation of a detonation or high order reaction. Second, ongoing detonations were successfully interrupted with EGP. LA-UR-15-20612.

  9. On the violence of thermal explosion in solid explosives

    SciTech Connect

    Chidester, S.K.; Tarver, C.M.; Green, L.G.; Urtiew, P.A.

    1997-07-01

    Heavily confined cylinders of octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX) and triaminotrinitrobenzene (TATB) were heated at rates varying from 2 C/min to 3.3 C/h. Fourteen of the cylinders were hollow, and inner metallic liners with small heaters attached were used to produce uniform temperatures just prior to explosion. A complex thermocouple pattern was used to measure the temperature history throughout the charge and to determine the approximate location where the runaway exothermic reaction first occurred. The violence of the resulting explosion was measured using velocity pin arrays placed inside and outside of the metal confinement cylinders, flash x-rays, overpressure gauges, and fragment collection techniques. Five cylinders were intentionally detonated for violence comparisons. The measured temperature histories, times to explosion, and the locations of first reaction agreed closely with those calculated by a two-dimensional heat transfer code using multistep chemical decomposition models. The acceleration of the confining metal cylinders by the explosion process was accurately simulated using a two-dimensional pressure dependent deflagration reactive flow hydrodynamic mode. The most violent HMX thermal explosions gradually accelerated their outer cases to velocities approaching those of intentional detonations approximately 120 {micro}m after the onset of explosion. The measured inner cylinder collapse velocities from thermal explosions were considerably lower than those produced by detonations. In contrast to the HMX thermal reactions, no violent thermal explosions were produced by the TATB-based explosive LX-17. A heavily confined, slowly heated LX-17 test produced sufficient pressure to cause a 0.1 cm bend in a 2 cm thick steel plate.

  10. The Examination of the Correlation between Social Physique Anxiety Levels and Narcissism Levels of the Students Who Studied at the SPES

    ERIC Educational Resources Information Center

    Gezer, Engin

    2014-01-01

    The aim of the study was to discover the correlation between social physique anxiety levels and narcissism levels of the students of the school of the physical education and sports. A total of 308 students who studied at different academic departments of the school of the physical education and sports of Mustafa Kemal University participated in…

  11. Optical detection of explosives: spectral signatures for the explosive bouquet

    NASA Astrophysics Data System (ADS)

    Osborn, Tabetha; Kaimal, Sindhu; Causey, Jason; Burns, William; Reeve, Scott

    2009-05-01

    Research with canines suggests that sniffer dogs alert not on the odor from a pure explosive, but rather on a set of far more volatile species present in an explosive as impurities. Following the explosive trained canine example, we have begun examining the vapor signatures for many of these volatile impurities utilizing high resolution spectroscopic techniques in several molecular fingerprint regions. Here we will describe some of these high resolution measurements and discuss strategies for selecting useful spectral signature regions for individual molecular markers of interest.

  12. Detection of explosives in soils

    DOEpatents

    Chambers, William B.; Rodacy, Philip J.; Phelan, James M.; Woodfin, Ronald L.

    2002-01-01

    An apparatus and method for detecting explosive-indicating compounds in subsurface soil. The apparatus has a probe with an adsorbent material on some portion of its surface that can be placed into soil beneath the ground surface, where the adsorbent material can adsorb at least one explosive-indicating compound. The apparatus additional has the capability to desorb the explosive-indicating compound through heating or solvent extraction. A diagnostic instrument attached to the probe detects the desorbed explosive-indicating compound. In the method for detecting explosive-indicating compounds in soil, the sampling probe with an adsorbent material on at least some portion of a surface of the sampling probe is inserted into the soil to contact the adsorbent material with the soil. The explosive-indicating compounds are then desorbed and transferred as either a liquid or gas sample to a diagnostic tool for analysis. The resulting gas or liquid sample is analyzed using at least one diagnostic tool selected from the group consisting of an ion-mobility spectrometer, a gas chromatograph, a high performance liquid chromatograph, a capillary electrophoresis chromatograph, a mass spectrometer, a Fourier-transform infrared spectrometer and a Raman spectrometer to detect the presence of explosive-indicating compounds.

  13. Discriminating between explosions and earthquakes

    NASA Astrophysics Data System (ADS)

    Cho, Kwang-Hyun

    2014-12-01

    Earthquake, explosion, and a nuclear test data are compared with forward modeling and band-pass filtered surface wave amplitude data for exploring methodologies to improve earthquake-explosion discrimination. The proposed discrimination method is based on the solutions of a double integral transformation in the wavenumber and frequency domains. Recorded explosion data on June 26, 2001 (39.212°N, 125.383°E) and October 30, 2001 (38.748°N, 125.267°E), a nuclear test on October 9, 2006 (41.275°N, 129.095°E), and two earthquakes on April 14, 2002 (39.207°N, 125.686°E) and June 7, 2002 (38.703°N, 125.638°E), all in North Korea, are used to discriminate between explosions and earthquakes by seismic wave analysis and numerical modeling. The explosion signal is characterized by first P waves with higher energy than that of S waves. Rg waves are clearly dominant at 0.05-0.5 Hz in the explosion data but not in the earthquake data. This feature is attributed to the dominant P waves in the explosion and their coupling with the SH components.

  14. Shock desensitizing of solid explosives

    SciTech Connect

    Davis, William C

    2010-01-01

    Solid explosive can be desensitized by a shockwave too weak to initiate it promptly, and desensitized explosive does not react although its chemical composition is almost unchanged. A strong second shock does not cause reaction until it overtakes the first shock. The first shock, if it is strong enough, accelerates very slowly at first, and then more rapidly as detonation approaches. These facts suggest that there are two competing reactions. One is the usual explosive goes to products with the release of energy, and the other is explosive goes to dead explosive with no chemical change and no energy release. The first reaction rate is very sensitive to the local state, and the second is only weakly so. At low pressure very little energy is released and the change to dead explosive dominates. At high pressure, quite the other way, most of the explosive goes to products. Numerous experiments in both the initiation and the full detonation regimes are discussed and compared in support of these ideas.

  15. Shock desensitizing of solid explosive

    SciTech Connect

    Davis, William C

    2010-01-01

    Solid explosive can be desensitized by a shock wave too weak to initiate it promptly, and desensitized explosive does not react although its chemical composition is almost unchanged. A strong second shock does not cause reaction until it overtakes the first shock. The first shock, if it is strong enough, accelerates very slowly at first, and then more rapidly as detonation approaches. These facts suggest that there are two competing reactions. One is the usual explosive goes to products with the release of energy, and the other is explosive goes to dead explosive with no chemical change and no energy release. The first reaction rate is very sensitive to the local state, and the second is only weakly so. At low pressure very little energy is released and the change to dead explosive dominates. At high pressure, quite the other way, most of the explosive goes to products. Numerous experiments in both the initiation and the full detonation regimes are discussed and compared in testing these ideas.

  16. Radiologic diagnosis of explosion casualties.

    PubMed

    Eastridge, Brian J; Blackbourne, Lorne; Wade, Charles E; Holcomb, John B

    2008-01-01

    The threat of terrorist events on domestic soil remains an ever-present risk. Despite the notoriety of unconventional weapons, the mainstay in the armament of the terrorist organization is the conventional explosive. Conventional explosives are easily weaponized and readily obtainable, and the recipes are widely available over the Internet. According to the US Department of State and the Federal Bureau of Investigation, over one half of the global terrorist events involve explosions, averaging two explosive events per day worldwide in 2005 (Terrorism Research Center. Available at www.terrorism.com. Accessed April 1, 2007). The Future of Emergency Care in the United States Health System: Emergency Medical Services at the Crossroads, published by the Institute of Medicine, states that explosions were the most common cause of injuries associated with terrorism (Institute of Medicine Report: The Future of Emergency Care in the United States Health System: Emergency Medical Services at the Crossroads. Washington DC: National Academic Press, 2007). Explosive events have the potential to inflict numerous casualties with multiple injuries. The complexity of this scenario is exacerbated by the fact that few providers or medical facilities have experience with mass casualty events in which human and material resources can be rapidly overwhelmed. Care of explosive-related injury is based on same principles as that of standard trauma management paradigms. The basic difference between explosion-related injury and other injury mechanisms are the number of patients and multiplicity of injuries, which require a higher allocation of resources. With this caveat, the appropriate utilization of radiology resources has the potential to impact in-hospital diagnosis and triage and is an essential element in optimizing the management of the explosive-injured patients. PMID:19069034

  17. Explosive signatures: Pre & post blast

    NASA Astrophysics Data System (ADS)

    Bernier, Evan Thomas

    Manuscripts 1 and 2 of this dissertation both involve the pre-blast detection of trace explosive material. The first manuscript explores the analysis of human hair as an indicator of exposure to explosives. Field analysis of hair for trace explosives is quick and non-invasive, and could prove to be a powerful linkage to physical evidence in the form of bulk explosive material. Individuals tested were involved in studies which required handling or close proximity to bulk high explosives such as TNT, PETN, and RDX. The second manuscript reports the results of research in the design and application of canine training aids for non-traditional, peroxide-based explosives. Organic peroxides such as triacetonetriperoxide (TATP) and hexamethylenetriperoxidediamine (HMTD) can be synthesized relatively easily with store-bought ingredients and have become popular improvised explosives with many terrorist groups. Due to the hazards of handling such sensitive compounds, this research established methods for preparing training aids which contained safe quantities of TATP and HMTD for use in imprinting canines with their characteristic odor. Manuscripts 3 and 4 of this dissertation focus on research conducted to characterize pipe bombs during and after an explosion (post-blast). Pipe bombs represent a large percentage of domestic devices encountered by law enforcement. The current project has involved the preparation and controlled explosion of over 90 pipe bombs of different configurations in order to obtain data on fragmentation patterns, fragment velocity, blast overpressure, and fragmentation distance. Physical data recorded from the collected fragments, such as mass, size, and thickness, was correlated with the relative power of the initial device. Manuscript 4 explores the microstructural analysis of select pipe bomb fragments. Shock-loading of the pipe steel led to plastic deformation and work hardening in the steel grain structure as evidenced by optical microscopy and

  18. Explosive percolation in thresholded networks

    NASA Astrophysics Data System (ADS)

    Hayasaka, Satoru

    2016-06-01

    Explosive percolation in a network is a phase transition where a large portion of nodes becomes connected with an addition of a small number of edges. Although extensively studied in random network models and reconstructed real networks, explosive percolation has not been observed in a more realistic scenario where a network is generated by thresholding a similarity matrix describing between-node associations. In this report, I examine construction schemes of such thresholded networks, and demonstrate that explosive percolation can be observed by introducing edges in a particular order.

  19. Light metal explosives and propellants

    DOEpatents

    Wood, Lowell L.; Ishikawa, Muriel Y.; Nuckolls, John H.; Pagoria, Phillip F.; Viecelli, James A.

    2005-04-05

    Disclosed herein are light metal explosives, pyrotechnics and propellants (LME&Ps) comprising a light metal component such as Li, B, Be or their hydrides or intermetallic compounds and alloys containing them and an oxidizer component containing a classic explosive, such as CL-20, or a non-explosive oxidizer, such as lithium perchlorate, or combinations thereof. LME&P formulations may have light metal particles and oxidizer particles ranging in size from 0.01 .mu.m to 1000 .mu.m.

  20. High Explosive Radio Telemetry System

    SciTech Connect

    Bracht, R.R.; Crawford, T.R.; Johnson, R.L.; Mclaughlin, B.M.

    1998-11-04

    This paper overviews the High Explosive Radio Telemetry (HERT) system, under co-development by Los Alamos National Laboratories and Allied Signal Federal Manufacturing & Technologies. This telemetry system is designed to measure the initial performance of an explosive package under flight environment conditions, transmitting data from up to 64 sensors. It features high speed, accurate time resolution (10 ns) and has the ability to complete transmission of data before the system is destroyed by the explosion. In order to affect the resources and performance of a flight delivery vehicle as little as possible, the system is designed such that physical size, power requirements, and antenna demands are as small as possible.

  1. Noise From Shallow Underwater Explosions

    NASA Astrophysics Data System (ADS)

    Soloway, Alexander G.

    Naval activities such as ordnance disposal, demolition and requisite training, can involve detonation of small explosive charges in shallow water that have the potential to harm nearby marine life. Measurements of the underwater sound generated by sub-surface explosions were collected as part of a naval training exercise. In this thesis the noise levels from these explosions will be investigated using peak pressure, sound exposure level and energy spectral density. Measurements of very-low frequency Scholte interface waves will also be presented and used to investigate elastic parameters in the sediment.

  2. Donor free radical explosive composition

    DOEpatents

    Walker, Franklin E. [15 Way Points Rd., Danville, CA 94526; Wasley, Richard J. [4290 Colgate Way, Livermore, CA 94550

    1980-04-01

    An improved explosive composition is disclosed and comprises a major portion of an explosive having a detonation velocity between about 1500 and 10,000 meters per second and a minor amount of a donor additive comprising an organic compound or mixture of organic compounds capable of releasing low molecular weight free radicals or ions under mechanical or electrical shock conditions and which is not an explosive, or an inorganic compound or mixture of inorganic compounds capable of releasing low molecular weight free radicals or ions under mechanical or electrical shock conditions and selected from ammonium or alkali metal persulfates.

  3. Evulvalution: the portrayal of women's external genitalia and physique across time and the current barbie doll ideals.

    PubMed

    Schick, Vanessa R; Rima, Brandi N; Calabrese, Sarah K

    2011-01-01

    Media images of the female body commonly represent reigning appearance ideals of the era in which they are published. To date, limited documentation of the genital appearance ideals in mainstream media exists. Analysis 1 sought to describe genital appearance ideals (i.e., mons pubis and labia majora visibility, labia minora size and color, and pubic hair style) and general physique ideals (i.e., hip, waist, and bust size, height, weight, and body mass index [BMI]) across time based on 647 Playboy Magazine centerfolds published between 1953 and 2007. Analysis 2 focused exclusively on the genital appearance ideals embodied by models in 185 Playboy photographs published between 2007 and 2008. Taken together, results suggest the perpetuation of a "Barbie Doll" ideal characterized by a low BMI, narrow hips, a prominent bust, and hairless, undefined genitalia resembling those of a prepubescent female. PMID:19916105

  4. Explosive Microsphere Particle Standards for Trace Explosive Detection Instruments

    NASA Astrophysics Data System (ADS)

    Staymates, Matthew; Fletcher, Robert; Gillen, Greg

    2007-11-01

    Increases in Homeland Security measures have led to a substantial deployment of trace explosive detection systems within the United States and US embassies around the world. One such system is a walk-through portal which aerodynamically screens people for trace explosive particles. Another system is a benchtop instrument that can detect explosives from swipes used to collect explosive particles from surfaces of luggage and clothing. The National Institute of Standards and Technology is involved in a chemical metrology program to support the operational deployment and effective utilization of trace explosive and narcotic detection devices and is working to develop a measurement infrastructure to optimize, calibrate and standardize these instruments. Well characterized test materials are essential for validating the performance of these systems. Particle size, chemical composition, and detector response are particularly important. Here, we describe one method for producing monodisperse polymer microspheres encapsulating trace explosives, simulants, and narcotics using a sonicated co-flow Berkland nozzle. The nozzle creates uniform droplets that undergo an oil/water emulsion process and cure to form hardened microspheres containing the desired analyte. Issues such as particle size, particle uniformity and levels of analyte composition will be discussed.

  5. Explosive Contagion in Networks

    NASA Astrophysics Data System (ADS)

    Gómez-Gardeñes, J.; Lotero, L.; Taraskin, S. N.; Pérez-Reche, F. J.

    2016-01-01

    The spread of social phenomena such as behaviors, ideas or products is an ubiquitous but remarkably complex phenomenon. A successful avenue to study the spread of social phenomena relies on epidemic models by establishing analogies between the transmission of social phenomena and infectious diseases. Such models typically assume simple social interactions restricted to pairs of individuals; effects of the context are often neglected. Here we show that local synergistic effects associated with acquaintances of pairs of individuals can have striking consequences on the spread of social phenomena at large scales. The most interesting predictions are found for a scenario in which the contagion ability of a spreader decreases with the number of ignorant individuals surrounding the target ignorant. This mechanism mimics ubiquitous situations in which the willingness of individuals to adopt a new product depends not only on the intrinsic value of the product but also on whether his acquaintances will adopt this product or not. In these situations, we show that the typically smooth (second order) transitions towards large social contagion become explosive (first order). The proposed synergistic mechanisms therefore explain why ideas, rumours or products can suddenly and sometimes unexpectedly catch on.

  6. Explosive actuated valve

    DOEpatents

    Byrne, Kenneth G.

    1983-01-01

    1. A device of the character described comprising the combination of a housing having an elongate bore and including a shoulder extending inwardly into said bore, a single elongate movable plunger disposed in said bore including an outwardly extending flange adjacent one end thereof overlying said shoulder, normally open conduit means having an inlet and an outlet perpendicularly piercing said housing intermediate said shoulder and said flange and including an intermediate portion intersecting and normally openly communicating with said bore at said shoulder, normally closed conduit means piercing said housing and intersecting said bore at a location spaced from said normally open conduit means, said elongate plunger including a shearing edge adjacent the other end thereof normally disposed intermediate both of said conduit means and overlying a portion of said normally closed conduit means, a deformable member carried by said plunger intermediate said flange and said shoulder and normally spaced from and overlying the intermediate portion of said normally open conduit means, and means on the housing communicating with the bore to retain an explosive actuator for moving said plunger to force the deformable member against the shoulder and extrude a portion of the deformable member out of said bore into portions of the normally open conduit means for plugging the same and to effect the opening of said normally closed conduit means by the plunger shearing edge substantially concomitantly with the plugging of the normally open conduit means.

  7. The Cambrian explosion.

    PubMed

    Briggs, Derek E G

    2015-10-01

    The sudden appearance of fossils that marks the so-called 'Cambrian explosion' has intrigued and exercised biologists since Darwin's time. In On the Origin of Species, Darwin made it clear that he believed that ancestral forms 'lived long before' their first fossil representatives. While he considered such an invisible record necessary to explain the level of complexity already seen in the fossils of early trilobites, Darwin was at a loss to explain why there were no corresponding fossils of these earlier forms. In chapter 9 of the Origin, entitled 'On the imperfection of the geological record', he emphasized the 'poorness of our palaeontological collections' and stated categorically that 'no organism wholly soft can be preserved'. Fortunately much has been discovered in the last 150 years, not least multiple examples of Cambrian and Precambrian soft-bodied fossils. We now know that the sudden appearance of fossils in the Cambrian (541-485 million years ago) is real and not an artefact of an imperfect fossil record: rapid diversification of animals coincided with the evolution of biomineralized shells. And although fossils in earlier rocks are rare, they are not absent: their rarity reflects the low diversity of life at this time, as well as the low preservation potential of Precambrian organisms (see Primer by Butterfield, in this issue). PMID:26439348

  8. Explosive actuated valves

    DOEpatents

    Cobb, Jr., Lawrence L.

    1983-01-01

    1. A device of the character described comprising the combination of a generally tubular housing having an end portion forming a chamber to receive the sensitive portion of an explosive squib, a plunger within said housing having an end portion exposed to said chamber, squib retaining means for engaging said housing and a said squib to releasably maintain the squib in close proximity to said plunger end portion including a retaining ring of fusible material spaced outwardly from and encircling at least part of a said squib and part of its sensitive portion for reception of heat from an external source prior to appreciable reception thereof by the sensitive portion of the squib, an annular compression spring bearing at one end against said housing for urging at least a portion of the squib retaining means and a said squib away from said housing and from said plunger end portion upon subjection of the fusible material to heat sufficient to melt at least a portion thereof, and guide means for said spring to maintain even expansion thereof as a said squib is being urged away from said housing.

  9. Explosive Contagion in Networks

    PubMed Central

    Gómez-Gardeñes, J.; Lotero, L.; Taraskin, S. N.; Pérez-Reche, F. J.

    2016-01-01

    The spread of social phenomena such as behaviors, ideas or products is an ubiquitous but remarkably complex phenomenon. A successful avenue to study the spread of social phenomena relies on epidemic models by establishing analogies between the transmission of social phenomena and infectious diseases. Such models typically assume simple social interactions restricted to pairs of individuals; effects of the context are often neglected. Here we show that local synergistic effects associated with acquaintances of pairs of individuals can have striking consequences on the spread of social phenomena at large scales. The most interesting predictions are found for a scenario in which the contagion ability of a spreader decreases with the number of ignorant individuals surrounding the target ignorant. This mechanism mimics ubiquitous situations in which the willingness of individuals to adopt a new product depends not only on the intrinsic value of the product but also on whether his acquaintances will adopt this product or not. In these situations, we show that the typically smooth (second order) transitions towards large social contagion become explosive (first order). The proposed synergistic mechanisms therefore explain why ideas, rumours or products can suddenly and sometimes unexpectedly catch on. PMID:26819191

  10. Disaster management following explosion.

    PubMed

    Sharma, B R

    2008-01-01

    Explosions and bombings remain the most common deliberate cause of disasters involving large numbers of casualties, especially as instruments of terrorism. These attacks are virtually always directed against the untrained and unsuspecting civilian population. Unlike the military, civilians are poorly equipped or prepared to handle the severe emotional, logistical, and medical burdens of a sudden large casualty load, and thus are completely vulnerable to terrorist aims. To address the problem to the maximum benefit of mass disaster victims, we must develop collective forethought and a broad-based consensus on triage and these decisions must reach beyond the hospital emergency department. It needs to be realized that physicians should never be placed in a position of individually deciding to deny treatment to patients without the guidance of a policy or protocol. Emergency physicians, however, may easily find themselves in a situation in which the demand for resources clearly exceeds supply and for this reason, emergency care providers, personnel, hospital administrators, religious leaders, and medical ethics committees need to engage in bioethical decision-making. PMID:18522253

  11. Furball Explosive Breakout Test

    SciTech Connect

    Carroll, Joshua David

    2015-08-05

    For more than 30 years the Onionskin test has been the primary way to study the surface breakout of a detonation wave. Currently the Onionskin test allows for only a small, one dimensional, slice of the explosive in question to be observed. Asymmetrical features are not observable with the Onionskin test and its one dimensional view. As a result, in 2011, preliminary designs for the Hairball and Furball were developed then tested. The Hairball used shorting pins connected to an oscilloscope to determine the arrival time at 24 discrete points. This limited number of data points, caused by the limited number of oscilloscope channels, ultimately led to the Hairball’s demise. Following this, the Furball was developed to increase the number of data points collected. Instead of shorting pins the Furball uses fiber optics imaged by a streak camera to determine the detonation wave arrival time for each point. The original design was able to capture the detonation wave’s arrival time at 205 discrete points with the ability to increase the number of data points if necessary.

  12. Explosive Contagion in Networks.

    PubMed

    Gómez-Gardeñes, J; Lotero, L; Taraskin, S N; Pérez-Reche, F J

    2016-01-01

    The spread of social phenomena such as behaviors, ideas or products is an ubiquitous but remarkably complex phenomenon. A successful avenue to study the spread of social phenomena relies on epidemic models by establishing analogies between the transmission of social phenomena and infectious diseases. Such models typically assume simple social interactions restricted to pairs of individuals; effects of the context are often neglected. Here we show that local synergistic effects associated with acquaintances of pairs of individuals can have striking consequences on the spread of social phenomena at large scales. The most interesting predictions are found for a scenario in which the contagion ability of a spreader decreases with the number of ignorant individuals surrounding the target ignorant. This mechanism mimics ubiquitous situations in which the willingness of individuals to adopt a new product depends not only on the intrinsic value of the product but also on whether his acquaintances will adopt this product or not. In these situations, we show that the typically smooth (second order) transitions towards large social contagion become explosive (first order). The proposed synergistic mechanisms therefore explain why ideas, rumours or products can suddenly and sometimes unexpectedly catch on. PMID:26819191

  13. The challenge of improvised explosives

    DOE PAGESBeta

    Maienschein, Jon L.

    2012-06-14

    Energetic materials have been developed for decades, and indeed centuries, with a common set of goals in mind. Performance (as a detonating explosive, a propellant, or a pyrotechnic) has always been key, equally important have been the attributes of safety, stability, and reproducibility. Research and development with those goals has led to the set of energetic materials commonly used today. In the past few decades, the adoption and use of improvised explosives in attacks by terrorists or third-world parties has led to many questions about these materials, e.g., how they may be made, what threat they pose to the intendedmore » target, how to handle them safely, and how to detect them. The unfortunate advent of improvised explosives has opened the door for research into these materials, and there are active programs in many countries. I will discuss issues and opportunities facing research into improvised explosives.« less

  14. Explosive plane-wave lens

    DOEpatents

    Marsh, Stanley P.

    1988-01-01

    An explosive plane-wave air lens which enables a spherical wave form to be converted to a planar wave without the need to specially machine or shape explosive materials is described. A disc-shaped impactor having a greater thickness at its center than around its periphery is used to convert the spherical wave into a plane wave. When the wave reaches the impactor, the center of the impactor moves first because the spherical wave reaches the center of the impactor first. The wave strikes the impactor later in time as one moves radially along the impactor. Because the impactor is thinner as one moves radially outward, the velocity of the impactor is greater at the periphery than at the center. An acceptor explosive is positioned so that the impactor strikes the acceptor simultaneously. Consequently, a plane detonation wave is propagated through the acceptor explosive.

  15. Explosive plane-wave lens

    DOEpatents

    Marsh, S.P.

    1988-03-08

    An explosive plane-wave air lens which enables a spherical wave form to be converted to a planar wave without the need to specially machine or shape explosive materials is described. A disc-shaped impactor having a greater thickness at its center than around its periphery is used to convert the spherical wave into a plane wave. When the wave reaches the impactor, the center of the impactor moves first because the spherical wave reaches the center of the impactor first. The wave strikes the impactor later in time as one moves radially along the impactor. Because the impactor is thinner as one moves radially outward, the velocity of the impactor is greater at the periphery than at the center. An acceptor explosive is positioned so that the impactor strikes the acceptor simultaneously. Consequently, a plane detonation wave is propagated through the acceptor explosive. 4 figs.

  16. Explosive plane-wave lens

    DOEpatents

    Marsh, S.P.

    1987-03-12

    An explosive plane-wave air lens which enables a spherical wave form to be converted to a planar wave without the need to specially machine or shape explosive materials is described. A disc-shaped impactor having a greater thickness at its center than around its periphery is used to convert the spherical wave into a plane wave. When the wave reaches the impactor, the center of the impactor moves first because the spherical wave reaches the center of the impactor first. The wave strikes the impactor later in time as one moves radially along the impactor. Because the impactor is thinner as one moves radially outward, the velocity of the impactor is greater at the periphery than at the center. An acceptor explosive is positioned so that the impactor strikes the acceptor simultaneously. Consequently, a plane detonation wave is propagated through the acceptor explosive. 3 figs., 3 tabs.

  17. Nuclear explosives for peaceful purposes

    SciTech Connect

    Borg, I.Y.

    1986-11-01

    The US Plowshare program, designed to develop peaceful uses of nuclear explosives, was vigorous between 1957-73 and was of concern during US and USSR nuclear treaty negotiations within that period. In order to accommodate possible future applications, the Peaceful Nuclear Explosions Treaty was signed in 1976. The US program explored the phenomenology of nuclear explosions and tested their use in industrial applications. Due to waning industrial interest and public concern over environmental issues, the US program was terminated in 1977. The Soviet counterpart to the Plowshare program, which has involved more than 100 experiments throughout the USSR, continued until the self-imposed moratorium in 1985. As any peaceful use of nuclear explosives has the potential of furthering weapons research, the US takes the position that all such experiments would have to be banned in a comprehensive test ban treaty. 24 refs.

  18. Explosive Spot Joining of Metals

    NASA Technical Reports Server (NTRS)

    Bement, Laurence J. (Inventor); Perry, Ronnie B. (Inventor)

    1997-01-01

    The invention is an apparatus and method for wire splicing using an explosive joining process. The apparatus consists of a prebend, U-shaped strap of metal that slides over prepositioned wires. A standoff means separates the wires from the strap before joining. An adhesive means holds two ribbon explosives in position centered over the U-shaped strap. A detonating means connects to the ribbon explosives. The process involves spreading strands of each wire to be joined into a flat plane. The process then requires alternating each strand in alignment to form a mesh-like arrangement with an overlapped area. The strap slides over the strands of the wires. and the standoff means is positioned between the two surfaces. The detonating means then initiates the ribbon explosives that drive the strap to accomplish a high velocity. angular collision between the mating surfaces. This collision creates surface melts and collision bonding resulting in electron-sharing linkups.

  19. The challenge of improvised explosives

    SciTech Connect

    Maienschein, Jon L.

    2012-06-14

    Energetic materials have been developed for decades, and indeed centuries, with a common set of goals in mind. Performance (as a detonating explosive, a propellant, or a pyrotechnic) has always been key, equally important have been the attributes of safety, stability, and reproducibility. Research and development with those goals has led to the set of energetic materials commonly used today. In the past few decades, the adoption and use of improvised explosives in attacks by terrorists or third-world parties has led to many questions about these materials, e.g., how they may be made, what threat they pose to the intended target, how to handle them safely, and how to detect them. The unfortunate advent of improvised explosives has opened the door for research into these materials, and there are active programs in many countries. I will discuss issues and opportunities facing research into improvised explosives.

  20. Explosion modelling for complex geometries

    NASA Astrophysics Data System (ADS)

    Nehzat, Naser

    A literature review suggested that the combined effects of fuel reactivity, obstacle density, ignition strength, and confinement result in flame acceleration and subsequent pressure build-up during a vapour cloud explosion (VCE). Models for the prediction of propagating flames in hazardous areas, such as coal mines, oil platforms, storage and process chemical areas etc. fall into two classes. One class involves use of Computation Fluid Dynamics (CFD). This approach has been utilised by several researchers. The other approach relies upon a lumped parameter approach as developed by Baker (1983). The former approach is restricted by the appropriateness of sub-models and numerical stability requirements inherent in the computational solution. The latter approach raises significant questions regarding the validity of the simplification involved in representing the complexities of a propagating explosion. This study was conducted to investigate and improve the Computational Fluid Dynamic (CFD) code EXPLODE which has been developed by Green et al., (1993) for use on practical gas explosion hazard assessments. The code employs a numerical method for solving partial differential equations by using finite volume techniques. Verification exercises, involving comparison with analytical solutions for the classical shock-tube and with experimental (small-scale, medium and large-scale) results, demonstrate the accuracy of the code and the new combustion models but also identify differences between predictions and the experimental results. The project has resulted in a developed version of the code (EXPLODE2) with new combustion models for simulating gas explosions. Additional features of this program include the physical models necessary to simulate the combustion process using alternative combustion models, improvement to the numerical accuracy and robustness of the code, and special input for simulation of different gas explosions. The present code has the capability of

  1. 36 CFR 1002.38 - Explosives.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 36 Parks, Forests, and Public Property 3 2012-07-01 2012-07-01 false Explosives. 1002.38 Section... RECREATION § 1002.38 Explosives. (a) Using, possessing, storing, or transporting explosives, blasting agents or explosive materials is prohibited, except pursuant to the terms and conditions of a permit....

  2. 30 CFR 77.1301 - Explosives; magazines.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Explosives; magazines. 77.1301 Section 77.1301... MANDATORY SAFETY STANDARDS, SURFACE COAL MINES AND SURFACE WORK AREAS OF UNDERGROUND COAL MINES Explosives and Blasting § 77.1301 Explosives; magazines. (a) Detonators and explosives other than blasting...

  3. 36 CFR 2.38 - Explosives.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 36 Parks, Forests, and Public Property 1 2012-07-01 2012-07-01 false Explosives. 2.38 Section 2.38... PROTECTION, PUBLIC USE AND RECREATION § 2.38 Explosives. (a) Using, possessing, storing, or transporting explosives, blasting agents or explosive materials is prohibited, except pursuant to the terms and...

  4. 32 CFR 234.9 - Explosives.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 32 National Defense 2 2012-07-01 2012-07-01 false Explosives. 234.9 Section 234.9 National Defense... PENTAGON RESERVATION § 234.9 Explosives. (a) Using, possessing, storing, or transporting explosives, blasting agents or explosive materials is prohibited, except pursuant to the terms and conditions of...

  5. 14 CFR 420.63 - Explosive siting.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 14 Aeronautics and Space 4 2013-01-01 2013-01-01 false Explosive siting. 420.63 Section 420.63... TRANSPORTATION LICENSING LICENSE TO OPERATE A LAUNCH SITE Responsibilities of a Licensee § 420.63 Explosive... configuration of the launch site follows its explosive site plan, and the licensee's explosive site...

  6. 32 CFR 234.9 - Explosives.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 2 2010-07-01 2010-07-01 false Explosives. 234.9 Section 234.9 National Defense... PENTAGON RESERVATION § 234.9 Explosives. (a) Using, possessing, storing, or transporting explosives, blasting agents or explosive materials is prohibited, except pursuant to the terms and conditions of...

  7. 36 CFR 2.38 - Explosives.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 36 Parks, Forests, and Public Property 1 2011-07-01 2011-07-01 false Explosives. 2.38 Section 2.38... PROTECTION, PUBLIC USE AND RECREATION § 2.38 Explosives. (a) Using, possessing, storing, or transporting explosives, blasting agents or explosive materials is prohibited, except pursuant to the terms and...

  8. 36 CFR 1002.38 - Explosives.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 36 Parks, Forests, and Public Property 3 2011-07-01 2011-07-01 false Explosives. 1002.38 Section... RECREATION § 1002.38 Explosives. (a) Using, possessing, storing, or transporting explosives, blasting agents or explosive materials is prohibited, except pursuant to the terms and conditions of a permit....

  9. 36 CFR 1002.38 - Explosives.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 36 Parks, Forests, and Public Property 3 2013-07-01 2012-07-01 true Explosives. 1002.38 Section... RECREATION § 1002.38 Explosives. (a) Using, possessing, storing, or transporting explosives, blasting agents or explosive materials is prohibited, except pursuant to the terms and conditions of a permit....

  10. 36 CFR 2.38 - Explosives.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 36 Parks, Forests, and Public Property 1 2010-07-01 2010-07-01 false Explosives. 2.38 Section 2.38... PROTECTION, PUBLIC USE AND RECREATION § 2.38 Explosives. (a) Using, possessing, storing, or transporting explosives, blasting agents or explosive materials is prohibited, except pursuant to the terms and...

  11. 30 CFR 77.1301 - Explosives; magazines.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Explosives; magazines. 77.1301 Section 77.1301... MANDATORY SAFETY STANDARDS, SURFACE COAL MINES AND SURFACE WORK AREAS OF UNDERGROUND COAL MINES Explosives and Blasting § 77.1301 Explosives; magazines. (a) Detonators and explosives other than blasting...

  12. 30 CFR 77.1301 - Explosives; magazines.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Explosives; magazines. 77.1301 Section 77.1301... MANDATORY SAFETY STANDARDS, SURFACE COAL MINES AND SURFACE WORK AREAS OF UNDERGROUND COAL MINES Explosives and Blasting § 77.1301 Explosives; magazines. (a) Detonators and explosives other than blasting...

  13. 36 CFR 1002.38 - Explosives.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Explosives. 1002.38 Section... RECREATION § 1002.38 Explosives. (a) Using, possessing, storing, or transporting explosives, blasting agents or explosive materials is prohibited, except pursuant to the terms and conditions of a permit....

  14. 36 CFR 2.38 - Explosives.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 36 Parks, Forests, and Public Property 1 2013-07-01 2013-07-01 false Explosives. 2.38 Section 2.38... PROTECTION, PUBLIC USE AND RECREATION § 2.38 Explosives. (a) Using, possessing, storing, or transporting explosives, blasting agents or explosive materials is prohibited, except pursuant to the terms and...

  15. 32 CFR 234.9 - Explosives.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 32 National Defense 2 2013-07-01 2013-07-01 false Explosives. 234.9 Section 234.9 National Defense... PENTAGON RESERVATION § 234.9 Explosives. (a) Using, possessing, storing, or transporting explosives, blasting agents or explosive materials is prohibited, except pursuant to the terms and conditions of...

  16. 32 CFR 234.9 - Explosives.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 32 National Defense 2 2011-07-01 2011-07-01 false Explosives. 234.9 Section 234.9 National Defense... PENTAGON RESERVATION § 234.9 Explosives. (a) Using, possessing, storing, or transporting explosives, blasting agents or explosive materials is prohibited, except pursuant to the terms and conditions of...

  17. 30 CFR 77.1301 - Explosives; magazines.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Explosives; magazines. 77.1301 Section 77.1301... MANDATORY SAFETY STANDARDS, SURFACE COAL MINES AND SURFACE WORK AREAS OF UNDERGROUND COAL MINES Explosives and Blasting § 77.1301 Explosives; magazines. (a) Detonators and explosives other than blasting...

  18. 30 CFR 77.1301 - Explosives; magazines.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Explosives; magazines. 77.1301 Section 77.1301... MANDATORY SAFETY STANDARDS, SURFACE COAL MINES AND SURFACE WORK AREAS OF UNDERGROUND COAL MINES Explosives and Blasting § 77.1301 Explosives; magazines. (a) Detonators and explosives other than blasting...

  19. 36 CFR 1002.38 - Explosives.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 36 Parks, Forests, and Public Property 3 2014-07-01 2014-07-01 false Explosives. 1002.38 Section... RECREATION § 1002.38 Explosives. (a) Using, possessing, storing, or transporting explosives, blasting agents or explosive materials is prohibited, except pursuant to the terms and conditions of a permit....

  20. 14 CFR 420.63 - Explosive siting.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 14 Aeronautics and Space 4 2014-01-01 2014-01-01 false Explosive siting. 420.63 Section 420.63... TRANSPORTATION LICENSING LICENSE TO OPERATE A LAUNCH SITE Responsibilities of a Licensee § 420.63 Explosive... configuration of the launch site follows its explosive site plan, and the licensee's explosive site...

  1. 36 CFR 2.38 - Explosives.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 36 Parks, Forests, and Public Property 1 2014-07-01 2014-07-01 false Explosives. 2.38 Section 2.38... PROTECTION, PUBLIC USE AND RECREATION § 2.38 Explosives. (a) Using, possessing, storing, or transporting explosives, blasting agents or explosive materials is prohibited, except pursuant to the terms and...

  2. 32 CFR 234.9 - Explosives.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 32 National Defense 2 2014-07-01 2014-07-01 false Explosives. 234.9 Section 234.9 National Defense... PENTAGON RESERVATION § 234.9 Explosives. (a) Using, possessing, storing, or transporting explosives, blasting agents or explosive materials is prohibited, except pursuant to the terms and conditions of...

  3. 30 CFR 7.306 - Explosion tests.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Explosion tests. 7.306 Section 7.306 Mineral... MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY Electric Motor Assemblies § 7.306 Explosion tests. (a) The following shall be used for conducting an explosion test: (1) An explosion test chamber...

  4. 30 CFR 7.306 - Explosion tests.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Explosion tests. 7.306 Section 7.306 Mineral... MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY Electric Motor Assemblies § 7.306 Explosion tests. (a) The following shall be used for conducting an explosion test: (1) An explosion test chamber...

  5. 30 CFR 7.306 - Explosion tests.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Explosion tests. 7.306 Section 7.306 Mineral... MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY Electric Motor Assemblies § 7.306 Explosion tests. (a) The following shall be used for conducting an explosion test: (1) An explosion test chamber...

  6. System for analysis of explosives

    DOEpatents

    Haas, Jeffrey S.

    2010-06-29

    A system for analysis of explosives. Samples are spotted on a thin layer chromatography plate. Multi-component explosives standards are spotted on the thin layer chromatography plate. The thin layer chromatography plate is dipped in a solvent mixture and chromatography is allowed to proceed. The thin layer chromatography plate is dipped in reagent 1. The thin layer chromatography plate is heated. The thin layer chromatography plate is dipped in reagent 2.

  7. Quantitative understanding of explosive stimulus transfer

    NASA Technical Reports Server (NTRS)

    Schimmel, M. L.

    1973-01-01

    The mechanisms of detonation transfer across hermetically sealed interfaces created by necessary interruptions in high explosive trains, such as at detonators to explosive columns, field joints in explosive columns, and components of munitions fuse trains are demostrated. Reliability of detonation transfer is limited by minimizing explosive quantities, the use of intensitive explosives for safety, and requirements to propagate across gaps and angles dictated by installation and production restraints. The major detonation transfer variables studied were: explosive quanity, sensitivity, and thickness, and the separation distances between donor and acceptor explosives.

  8. The characterization and evaluation of accidental explosions

    NASA Technical Reports Server (NTRS)

    Strehlow, R. A.; Baker, W. E.

    1975-01-01

    Accidental explosions are discussed from a number of viewpoints. First, all accidental explosions, intentional explosions and natural explosions are characterized by type. Second, the nature of the blast wave produced by an ideal (point source or HE) explosion is discussed to form a basis for describing how other explosion processes yield deviations from ideal blast wave behavior. The current status blast damage mechanism evaluation is also discussed. Third, the current status of our understanding of each different category of accidental explosions is discussed in some detail.

  9. The Explosion of Cassiopeia A

    NASA Astrophysics Data System (ADS)

    Hwang, Una

    2005-10-01

    The 330 year old Galactic supernova remnant Cassiopeia A offers a uniquely detailed look at the supernova ejecta formed during its explosion through current X-ray and optical observations, including a deep 1Ms observation with the Chandra Observatory. The explosively synthesized ejecta are distributed in small-scale knots and filaments with an overall bipolar symmetry and X-ray spectra dominated by emission lines of Si, S, Ar, and Ca, with some Fe, except in Fe-rich regions of the remnant where the Fe lines are very strong. The displacement of the compact stellar remnant relative to the optically determined explosion center indicates that the birth kick of the neutron star had a component perpendicular to the polar axis of the ejecta. From modelling the X-ray spectra, we learn that the explosion energy was distributed aspherically, that the progenitor underwent substantial mass loss, and that the ejecta along the polar axes originated as ``jets'' during the explosion rather than being shaped by the progenitor's pre-supernova mass loss. The energetics of Cas A's explosion indicates that it was probably formed as a slightly energetic supernova.

  10. Microbial remediation of explosive waste.

    PubMed

    Singh, Baljinder; Kaur, Jagdeep; Singh, Kashmir

    2012-05-01

    Explosives are synthesized globally mainly for military munitions. Nitrate esters, such as GTN and PETN, nitroaromatics like TNP and TNT and nitramines with RDX, HMX and CL20, are the main class of explosives used. Their use has resulted in severe contamination of environment and strategies are now being developed to clean these substances in an economical and eco-friendly manner. The incredible versatility inherited in microbes has rendered these explosives as a part of the biogeochemical cycle. Several microbes catalyze mineralization and/or nonspecific transformation of explosive waste either by aerobic or anaerobic processes. It is likely that ongoing genetic adaptation, with the recruitment of silent sequences into functional catabolic routes and evolution of substrate range by mutations in structural genes, will further enhance the catabolic potential of bacteria toward explosives and ultimately contribute to cleansing the environment of these toxic and recalcitrant chemicals. This review summarizes information on the biodegradation and biotransformation pathways of several important explosives. Isolation, characterization, utilization and manipulation of the major detoxifying enzymes and the molecular basis of degradation are also discussed. This may be useful in developing safer and economic microbiological methods for clean up of soil and water contaminated with such compounds. The necessity of further investigations concerning the microbial metabolism of these substances is also discussed. PMID:22497284

  11. Explosive Characteristics of Carbonaceous Nanoparticles

    NASA Astrophysics Data System (ADS)

    Turkevich, Leonid; Fernback, Joseph; Dastidar, Ashok

    2013-03-01

    Explosion testing has been performed on 20 codes of carbonaceous particles. These include SWCNTs (single-walled carbon nanotubes), MWCNTs (multi-walled carbon nanotubes), CNFs (carbon nanofibers), graphene, diamond, fullerene, carbon blacks and graphites. Explosion screening was performed in a 20 L explosion chamber (ASTM E1226-10 protocol), at a (dilute) concentration of 500 g/m3, using a 5 kJ ignition source. Time traces of overpressure were recorded. Samples exhibited overpressures of 5-7 bar, and deflagration index KSt = V1/3 (dp/pt)max ~ 10 - 80 bar-m/s, which places these materials in European Dust Explosion Class St-1 (similar to cotton and wood dust). There was minimal variation between these different materials. The explosive characteristics of these carbonaceous powders are uncorrelated with particle size (BET specific surface area). Additional tests were performed on selected materials to identify minimum explosive concentration [MEC]. These materials exhibit MEC ~ 101 -102 g/m3 (lower than the MEC for coals). The concentration scans confirm that the earlier screening was performed under fuel-rich conditions (i.e. the maximum over-pressure and deflagration index exceed the screening values); e.g. the true fullerene KSt ~ 200 bar-m/s, placing it borderline St-1/St-2. Work supported through the NIOSH Nanotechnology Research Center (NTRC)

  12. Ensemble des troubles causés par l'alcoolisation fœtale : lignes directrices canadiennes concernant le diagnostic

    PubMed Central

    Chudley, Albert E.; Conry, Julianne; Cook, Jocelynn L.; Loock, Christine; Rosales, Ted; LeBlanc, Nicole

    2005-01-01

    Résumé LE DIAGNOSTIC DE L'ENSEMBLE DES TROUBLES CAUSÉS PAR L'ALCOOLISATION FÉTALE (ETCAF) est complexe et l'élaboration de lignes directrices concernant le diagnostic est justifiée. Un sous-comité du Comité consultatif national de l'Agence de santé publique du Canada sur l'Ensemble des troubles causés par l'alcoolisation fœtale a examiné, analysé et intégré les méthodes de diagnostic actuelles afin de parvenir à une méthode de diagnostic normalisée faisant le consensus au Canada. L'objet du présent document est d'examiner et de clarifier l'utilisation des systèmes de diagnostic actuels et de formuler des recommandations quant à leur application pour le diagnostic des déficiences liées à l'ETCAF chez des individus de tous les âges. Les lignes directrices sont fondées sur un vaste consensus de praticiens et d'autres intervenants spécialisés dans le domaine. Ces lignes directrices ont été organisées en sept catégories, soit le dépistage et l'orientation vers les spécialistes, l'examen physique et le diagnostic différentiel, l'évaluation du comportement neurologique, le traitement et le suivi, les antécédents de consommation d'alcool de la mère pendant la grossesse, les critères du diagnostic pour le syndrome d'alcoolisation fœtale (SAF), SAF partiel et troubles neurologiques du développement liés à l'alcool, l'harmonisation de l'Institute of Medicine (IOM) et des approches du Code diagnostique à 4 chiffres. Le diagnostic exige une évaluation complète des antécédents, ainsi qu'un examen physique et du comportement neurologique, tout en recourant à une approche multidisciplinaire. Les présentes lignes directrices pour le diagnostic du syndrome d'alcoolisation fœtale et des déficiences qui y sont associées sont les premières à avoir été élaborées au Canada et elles sont fondées sur la consultation d'un grand éventail de spécialistes du diagnostic.

  13. The Quiet Explosion

    NASA Astrophysics Data System (ADS)

    2008-07-01

    A European-led team of astronomers are providing hints that a recent supernova may not be as normal as initially thought. Instead, the star that exploded is now understood to have collapsed into a black hole, producing a weak jet, typical of much more violent events, the so-called gamma-ray bursts. The object, SN 2008D, is thus probably among the weakest explosions that produce very fast moving jets. This discovery represents a crucial milestone in the understanding of the most violent phenomena observed in the Universe. Black Hole ESO PR Photo 23a/08 A Galaxy and two Supernovae These striking results, partly based on observations with ESO's Very Large Telescope, will appear tomorrow in Science Express, the online version of Science. Stars that were at birth more massive than about 8 times the mass of our Sun end their relatively short life in a cosmic, cataclysmic firework lighting up the Universe. The outcome is the formation of the densest objects that exist, neutron stars and black holes. When exploding, some of the most massive stars emit a short cry of agony, in the form of a burst of very energetic light, X- or gamma-rays. In the early afternoon (in Europe) of 9 January 2008, the NASA/STFC/ASI Swift telescope discovered serendipitously a 5-minute long burst of X-rays coming from within the spiral galaxy NGC 2770, located 90 million light-years away towards the Lynx constellation. The Swift satellite was studying a supernova that had exploded the previous year in the same galaxy, but the burst of X-rays came from another location, and was soon shown to arise from a different supernova, named SN 2008D. Researchers at the Italian National Institute for Astrophysics (INAF), the Max-Planck Institute for Astrophysics (MPA), ESO, and at various other institutions have observed the supernova at great length. The team is led by Paolo Mazzali of INAF's Padova Observatory and MPA. "What made this event very interesting," says Mazzali, "is that the X-ray signal was very

  14. La physique des bulles de champagne Une première approche des processus physico-chimiques liés à l'effervescence des vins de Champagne

    NASA Astrophysics Data System (ADS)

    Liger-Belair, G.

    2002-07-01

    People have long been fascinated by bubbles and foams dynamics, and since the pioneering work of Leonardo da Vinci in the early 16th century, this subject has generated a huge bibliography. However, only very recently, much interest was devoted to bubbles in Champagne wines. Small bubbles rising through the liquid, as well as a bubble ring (the so-called collar) at the periphery of a flute poured with champagne are the hallmark of this traditionally festive wine, and even there is no scientific evidence yet to connect the quality of a champagne with its effervescence, people nevertheless often make a connection between them. Therefore, since the last few years, a better understanding of the numerous parameters involved in the bubbling process has become an important stake in the champagne research area. Otherwise, in addition to these strictly enological reasons, we also feel that the area of bubble dynamics could benefit from the simple but close observation of a glass poured with champagne. In this study, our first results concerning the close observation of the three main steps of a champagne bubble's life are presented, that is, the bubble nucleation on tiny particles stuck on the glass wall (Chap. 2), the bubble ascent through the liquid (Chap. 3), and the bursting of bubbles at the free surface, which constitutes the most intriguing and visually appealing step (Chap. 4). Our results were obtained in real consuming conditions, that is, in a classical crystal flute poured with a standard commercial champagne wine. Champagne bubble nucleation proved to be a fantastic everyday example to illustrate the non-classical heterogeneous bubble nucleation process in a weakly supersaturated liquid. Contrary to a generally accepted idea, nucleation sites are not located on irregularities of the glass itself. Most of nucleation sites are located on tiny hollow and roughly cylindrical exogenous fibres coming from the surrounding air or remaining from the wiping process. Because of their geometry and hydrophobic properties, such particles are able to entrap gas pockets during the filling of a flute and to start up the bubble production process. Such particles are responsible for the clockwork and repetitive production of bubbles that rise in-line into the form of elegant bubble trains. This cycle of bubble production at a given nucleation site is characterised by its bubbling frequency. The time needed to reach the moment of bubble detachment depends on the kinetics of the CO2 molecules transfer from the champagne to the gas pocket, but also on the geometrical properties of the given nucleation site. Now, since a collection of particle shapes and sizes exists on the glass wall, the bubbling frequency may also vary from one site to another. Three minutes after pouring, we measured bubbling frequencies ranging from less than 1 Hz up to almost 30 Hz, which means that the most active nucleation sites emit up to 30 bubbles per second. After their detachment from nucleation sites, champagne bubbles rise in-line through the liquid into the form of elegant bubble trains. Since they collect dissolved carbon dioxide molecules, champagne bubbles expand during ascent and therefore constitute an original tool to investigate the dynamics of rising and expanding bubbles. Hydrodynamically speaking, champagne bubbles were found to reach a quasi-stationary stage intermediate between that of a rigid and that a fluid sphere (but nevertheless closer to that of a fluid sphere). This result drastically differs from the result classically observed with bubbles of fixed radii rising in surfactant solutions. Since surfactants progressively adsorb at the bubble surface during the rise, the drag coefficient of a rising bubble of fixed radius progressively increases, and finally reaches the rigid sphere limit when the bubble interface gets completely contaminated. In the case of champagne, since a bubble expands during its rise through the supersaturated liquid, the bubble interface continuously increases and therefore continuously offers newly created surface

  15. Recycled ejecta modulating Strombolian explosions

    NASA Astrophysics Data System (ADS)

    Capponi, Antonio; Taddeucci, Jacopo; Scarlato, Piergiorgio; Palladino, Danilo M.

    2016-02-01

    Two main end-members of eruptive regimes are identified from analyses of high-speed videos collected at Stromboli volcano (Italy), based on vent conditions: one where the vent is completely clogged by debris, and a second where the vent is open, without any cover. By detailing the vent processes for each regime, we provide the first account of how the presence of a cover affects eruptive dynamics compared to open-vent explosions. For clogged vents, explosion dynamics are controlled by the amount and grain size of the debris. Fine-grained covers are entirely removed by explosions, favouring the generation of fine ash plumes, while coarse-grained covers are only partially removed by the explosions, involving minor amounts of ash. In both fine- and coarse-grained cases, in-vent ground deformation of the debris reflect variations in the volumetric expansion of gas in the conduit, with rates of change of the deformation comparable to ground inflation related to pre-burst conduit pressurization. Eruptions involve the ejection of relatively slow and cold bombs and lapilli, and debris is observed to both fall back into the vent after each explosion and to gravitationally accumulate between explosions by rolling down the inner crater flanks to produce the cover itself. Part of this material may also contribute to the formation of a more degassed, crystallized and viscous magma layer at the top of the conduit. Conversely, open-vent explosions erupt with hotter pyroclasts, with higher exit velocity and with minor or no ash phase involved.

  16. Shock Initiation of Heterogeneous Explosives

    SciTech Connect

    Reaugh, J E

    2004-05-10

    The fundamental picture that shock initiation in heterogeneous explosives is caused by the linking of hot spots formed at inhomogeneities was put forward by several researchers in the 1950's and 1960's, and more recently. Our work uses the computer hardware and software developed in the Advanced Simulation and Computing (ASC) program of the U.S. Department of Energy to explicitly include heterogeneities at the scale of the explosive grains and to calculate the consequences of realistic although approximate models of explosive behavior. Our simulations are performed with ALE-3D, a three-dimensional, elastic-plastic-hydrodynamic Arbitrary Lagrange-Euler finite-difference program, which includes chemical kinetics and heat transfer, and which is under development at this laboratory. We developed the parameter values for a reactive-flow model to describe the non-ideal detonation behavior of an HMX-based explosive from the results of grain-scale simulations. In doing so, we reduced the number of free parameters that are inferred from comparison with experiment to a single one - the characteristic defect dimension. We also performed simulations of the run to detonation in small volumes of explosive. These simulations illustrate the development of the reaction zone and the acceleration of the shock front as the flame fronts start from hot spots, grow, and interact behind the shock front. In this way, our grain-scale simulations can also connect to continuum experiments directly.

  17. Thermodynamic States in Explosion Fields

    SciTech Connect

    Kuhl, A L

    2009-10-16

    Here we investigate the thermodynamic states occurring in explosion fields from the detonation of condensed explosives in air. In typical applications, the pressure of expanded detonation products gases is modeled by a Jones-Wilkins-Lee (JWL) function: P{sub JWL} = f(v,s{sub CJ}); constants in that function are fit to cylinder test data. This function provides a specification of pressure as a function of specific volume, v, along the expansion isentrope (s = constant = s{sub CJ}) starting at the Chapman-Jouguet (CJ) state. However, the JWL function is not a fundamental equation of thermodynamics, and therefore gives an incomplete specification of states. For example, explosions inherently involve shock reflections from surfaces; this changes the entropy of the products, and in such situations the JWL function provides no information on the products states. In addition, most explosives are not oxygen balanced, so if hot detonation products mix with air, they after-burn, releasing the heat of reaction via a turbulent combustion process. This raises the temperature of explosion products cloud to the adiabatic flame temperature ({approx}3,000K). Again, the JWL function provides no information on the combustion products states.

  18. La physique à l'échelle du TeV

    NASA Astrophysics Data System (ADS)

    Chiappetta, P.

    We first stress that very energetic hadronic colliders (LHC/SSC) have to be built in order to clarify the mechanism of electroweak symmetry breaking. We show that discovery of a fundamental Higgs scalar is possible in the range 130 ≤ MH ≤ 800 GeV and the importance of an e+e- collider to discover a Higgs in the range 90 < MH ≤ 200 GeV. Then we will discuss the potentialities of LHC/SSC for discovery of supersymmetric partners up to the crucial TeV scale. Ways to find a strongly interacting Higgs sector (without existence of a fundamental Higgs) are finally given. On souligne tout d'abord la nécessité de construire des accélérateurs hadroniques (LHC/SSC) très énergétiques pour clarifier le mécanisme de brisure de la symétrie électrofaible. On montre que la découverte d'un scalaire de Higgs fondamental est possible dans le domaine 130 ≤ M H ≤ 800 GeV et l'intérêt d'un collisionneur e+e - pour observer un Higgs dans le domaine 90 GeV ≤ M H ≤ 200 GeV On passera ensuite en revue les potentialités du LHC/SSC concernant la découverte de partenaires supersymétriques jusqu'à l'échelle cruciale du TeV Les moyens d'observer un secteur de Higgs fortement interagissant (cas où un Higgs fondamental n'existe pas) sont enfin indiqués.

  19. Des ballons pour demain

    NASA Astrophysics Data System (ADS)

    Régipa, R.

    A partir d'une théorie sur la détermination des formes et des contraintes globales d'un ballon de révolution, ou s'en rapprochant, une nouvelle famille de ballons a été définie. Les ballons actuels, dits de ``forme naturelle'', sont calculés en général pour une tension circonférencielle nulle. Ainsi, pour une mission donnée, la tension longitudinale et la forme de l'enveloppe sont strictement imposées. Les ballons de la nouvelle génération sont globalement cylindriques et leurs pôles sont réunis par un câble axial, chargé de transmettre une partie des efforts depuis le crochet (pôle inférieur), directement au pôle supérieur. De plus, la zone latérale cylindrique est soumise à un faible champ de tensions circonférencielles. Ainsi, deux paramètres permettent de faire évoluer la distribution des tensions et la forme de l'enveloppe: - la tension du câble de liaison entre pôles (ou la longueur de ce câble) - la tension circonférencielle moyenne désirée (ou le rayon du ballon). On peut donc calculer et réaliser: - soit des ballons de forme adaptée, comme les ballons à fond plat pour le bon fonctionnement des montgolfières infrarouge (projet MIR); - soit des ballons optimisés pour une bonne répartition des contraintes et une meilleure utilisation des matériaux d'enveloppe, pour l'ensemble des programmes stratosphériques. Il s'ensuit une économie sensible des coûts de fabrication, une fiabilité accrue du fonctionnement de ces ballons et une rendement opérationnel bien supérieur, permettant entre autres, d'envisager des vols à très haute altitude en matériaux très légers.

  20. The vapor pressures of explosives

    SciTech Connect

    Ewing, Robert G.; Waltman, Melanie J.; Atkinson, David A.; Grate, Jay W.; Hotchkiss, Peter

    2013-01-05

    The vapor pressures of many explosive compounds are extremely low and thus determining accurate values proves difficult. Many researchers, using a variety of methods, have measured and reported the vapor pressures of explosives compounds at single temperatures, or as a function of temperature using vapor pressure equations. There are large variations in reported vapor pressures for many of these compounds, and some errors exist within individual papers. This article provides a review of explosive vapor pressures and describes the methods used to determine them. We have compiled primary vapor pressure relationships traceable to the original citations and include the temperature ranges for which they have been determined. Corrected values are reported as needed and described in the text. In addition, after critically examining the available data, we calculate and tabulate vapor pressures at 25 °C.

  1. Permeability enhancement using explosive techniques

    SciTech Connect

    Adams, T.F.; Schmidt, S.C.; Carter, W.J.

    1980-01-01

    In situ recovery methods for many of our hydrocarbon and mineral resources depend on the ability to create or enhance permeability in the resource bed to allow uniform and predictable flow. To meet this need, a new branch of geomechanics devoted to computer prediction of explosive rock breakage and permeability enhancement has developed. The computer is used to solve the nonlinear equations of compressible flow, with the explosive behavior and constitutive properties of the medium providing the initial/boundary conditions and material response. Once the resulting computational tool has been verified and calibrated with appropriate large-scale field tests, it can be used to develop and optimize commercially useful explosive techniques for in situ resource recovery.

  2. Explosive evaporation in solar flares

    NASA Technical Reports Server (NTRS)

    Fisher, George H.

    1987-01-01

    This paper develops a simple analytical model for the phenomenon of 'explosive evaporation' driven by nonthermal electron heating in solar flares. The model relates the electron energy flux and spectrum, plus details of the preflare atmosphere, to the time scale for explosive evaporation to occur, the maximum pressure and temperature to be reached, rough estimates for the UV pulse emission flux and duration, and the evolution of the blueshifted component of the soft X-ray lines. An expression is given for the time scale for buildup to maximum pressures and the onset of rapid motion of the explosively evaporating plasma. This evaporation can excite a rapid response of UV line and continuum emission. The emission lines formed in the plasma approach a given emissivity-weighted blueshift speed.

  3. Optimal dynamic detection of explosives

    SciTech Connect

    Moore, David Steven; Mcgrane, Shawn D; Greenfield, Margo T; Scharff, R J; Rabitz, Herschel A; Roslund, J

    2009-01-01

    The detection of explosives is a notoriously difficult problem, especially at stand-off distances, due to their (generally) low vapor pressure, environmental and matrix interferences, and packaging. We are exploring optimal dynamic detection to exploit the best capabilities of recent advances in laser technology and recent discoveries in optimal shaping of laser pulses for control of molecular processes to significantly enhance the standoff detection of explosives. The core of the ODD-Ex technique is the introduction of optimally shaped laser pulses to simultaneously enhance sensitivity of explosives signatures while reducing the influence of noise and the signals from background interferents in the field (increase selectivity). These goals are being addressed by operating in an optimal nonlinear fashion, typically with a single shaped laser pulse inherently containing within it coherently locked control and probe sub-pulses. With sufficient bandwidth, the technique is capable of intrinsically providing orthogonal broad spectral information for data fusion, all from a single optimal pulse.

  4. Seismic coupling of nuclear explosions

    SciTech Connect

    Larson, D.B. )

    1989-01-01

    The new Giant Magnet Experimental Facility employing digital recording of explosion induced motion has been constructed and successfully tested. Particle velocity and piezoresistance gage responses can be measured simultaneously thus providing the capability for determining the multi-component stress-strain history in the test material. This capability provides the information necessary for validation of computer models used in simulation of nuclear underground testing, chemical explosion testing, dynamic structural response, earth penetration response, and etc. This report discusses fully coupled and cavity decoupled explosions of the same energy (0.622 kJ) were carried out as experiments to study wave propagation and attenuation in polymethylmethacrylate (PMMA). These experiments produced particle velocity time histories at strains from 2 [times] 10[sup [minus]3] to as low as 5.8 [times] 10[sup [minus]6]. Other experiments in PMMA, reported recently by Stout and Larson[sup 8] provide additional particle velocity data to strains of 10[sup [minus]1].

  5. Laser synchronization of a thermal explosion

    NASA Astrophysics Data System (ADS)

    Smilowitz, L.; Henson, B. F.; Sandstrom, M. M.; Romero, J. J.; Asay, B. W.

    2007-06-01

    The authors describe a method by which prompt ignition of thermal explosions is achieved. A convergent heating geometry is applied to a solid cylindrical explosive generating spatial temperature gradients which define a thermal ignition volume. A laser pulse is introduced via an optical fiber to apply a nonshock temperature perturbation in this volume seconds prior the normal ignition time. Explosion occurs hundreds of microseconds subsequent to this perturbation. They show that the subsequent explosive response is identical to that of a normal thermal explosion. This synchronization method enables fast radiographic imaging of nonlinear thermal explosion.

  6. Insensitive fuze train for high explosives

    DOEpatents

    Cutting, Jack L.; Lee, Ronald S.; Von Holle, William G.

    1994-01-01

    A generic insensitive fuze train to initiate insensitive high explosives, such as PBXW-124. The insensitive fuze train uses a slapper foil to initiate sub-gram quantities of an explosive, such as HNS-IV or PETN. This small amount of explosive drives a larger metal slapper onto a booster charge of an insensitive explosive, such as UF-TATB. The booster charge initiates a larger charge of an explosive, such as LX-17, which in turn, initiates the insensitive high explosive, such as PBXW-124.

  7. Insensitive fuze train for high explosives

    DOEpatents

    Cutting, J.L.; Lee, R.S.; Von Holle, W.G.

    1994-01-04

    A generic insensitive fuze train to initiate insensitive high explosives, such as PBXW-124 is described. The insensitive fuze train uses a slapper foil to initiate sub-gram quantities of an explosive, such as HNS-IV or PETN. This small amount of explosive drives a larger metal slapper onto a booster charge of an insensitive explosive, such as UF-TATB. The booster charge initiates a larger charge of an explosive, such as LX-17, which in turn, initiates the insensitive high explosive, such as PBXW-124. 3 figures.

  8. Etude des parametres physiques en vue d'applications medicales de l'actionnement magnetique de dispositifs medicaux par un systeme d'imagerie par resonance magnetique

    NASA Astrophysics Data System (ADS)

    Mathieu, Jean-Baptiste

    An actuation and control method for medical devices based on the magnetic gradient coils of a Magnetic Resonance Imaging (MRI) was proposed for the first time in 2002 by NanoRobotics Laboratory [1]. The work undertaken in the present thesis began in the context of demonstrating the concept of automatic navigation of a magnetic bead in vivo. From the point of view of actuation, models and experimental data correlate. A maximum velocity of 13cm/s was measured for a 1.5mm diameter chrome steel bead in the carotid artery of a living swine. The bead was under the influence of magnetic gradients applied by a clinical MRI system without any hardware modification. In light of these results, the aim of this thesis is the study of the physical parameters involved in the development of a first medical application: the steering of magnetic particles in MRI in the context of drug targeting. It was demonstrated that an MRI system equipped with a set of magnetic gradient coils with enhanced amplitude was able to apply a high enough actuation force to act upon magnetic microparticles suspended in a liquid. General rules for MRI actuation were identified. First of all, increasing the amplitude of the main magnetic field of the MRI leads to the increase of the actuation force amplitude only until the ferromagnetic body reaches its saturation magnetization. Moreover, soft ferromagnetic bodies appear to be better candidates for MRI based magnetic actuation because they can reach high saturation magnetizations. Magnetic gradient amplitude appears as a foremost factor to increase the amplitude of the magnetic force. Clinical MRI systems do not provide gradients with high enough amplitude for the applications studied here. Theoretical models developed in this thesis predict that a one order of magnitude increase in gradient amplitude would be required. Implementing actuation dedicated gradient coils is therefore suggested. Finally, a larger ferromagnetic body will lead to higher magnetophoretic velocities for magnetic particles. In the context of magnetic microparticle targeting for cancer treatment through embolisation, the scaling laws bridging from the preliminary works with millimeter sized beads to magnetic microparticles suspensions were studied. Magnetic microparticles suspensions injected through branching channels were guided in MRI under the influence of magnetic gradients. The goal of these experiments was to maximize the amount of particles flowing through one of the outlets of the channel. The outcome of the experiments was quantified using an optical set-up as well as by analyzing the suspension at each outlet of the channels. The most important parameters that were identified are the magnetic force amplitude, the interactions and aggregation between magnetic particles of the suspension, the size, geometry and density of the particles or aggregates driven, the dimensions of the channel and the intensity of the flow. Mathematical models based on analyses of particle trajectories and on non dimensionalization of the experimental parameters were proposed. The model predicts steering efficiencies in the order of what was recorded experimentally. Nevertheless, some parameters that remain to be quantified more precisely like the effects of magnetic aggregation and friction forces cause discrepancies between theoretical and experimental data. Despite these differences, the knowledge gained in the field of magnetic suspension steering appears to be sufficient to envision in vivo experiments lead in parallel with improving the theoretical predictions. Hence, an experimental set-up and an experimental protocol are being designed to adapt the steering methods to interventional procedures and animal subjects. Finally, the same principles used for microparticle steering can be applied for magnetic catheter navigation. Hence, on the side of the main subject of this thesis, the deflection of magnetic catheters by MRI was also studied as a second medical application. Using magnetic catheter and guide wires could facilitate the placement of medical instruments and accelerate medical procedures. The recorded deflections are lower than the ones measured with other magnetic guidance systems. The parameters and performances obtained are functions of the amplitude of the applied magnetic force and material strength properties of the catheters or guide wires. Hence, deflection could be enhanced by adapting the mechanical properties of the devices, by increasing the amplitude of the magnetic gradient or the volume and magnetization of the magnetic tip. These latter results are the object of an upcoming patent application. Hence, the paper relating them could not be submitted prior to the submission date of this thesis. For this reason, this paper's manuscript is presented as an annex of the present document

  9. Modelisation numerique des phenomenes physiques du soudage par friction-malaxage et comportement en fatigue de joints soudes en aluminium 7075-T6

    NASA Astrophysics Data System (ADS)

    Gemme, Frederic

    The aim of the present research project is to increase the amount of fundamental knowledge regarding the process by getting a better understanding of the physical phenomena involved in friction stir welding (FSW). Such knowledge is required to improve the process in the context of industrial applications. In order to do so, the first part of the project is dedicated to a theoretical study of the process, while the microstructure and the mechanical properties of welded joints obtained in different welding conditions are measured and analyzed in the second part. The combination of the tool rotating and translating movements induces plastic deformation and heat generation of the welded material. The material thermomechanical history is responsible for metallurgical phenomena occurring during FSW such as recrystallization and precipitate dissolution and coarsening. Process modelling is used to reproduce this thermomechanical history in order to predict the influence of welding on the material microstructure. It is helpful to study heat generation and heat conduction mechanisms and to understand how joint properties are related to them. In the current work, a finite element numerical model based on solid mechanics has been developed to compute the thermomechanical history of the welded material. The computation results were compared to reference experimental data in order to validate the model and to calibrate unknown physical parameters. The model was used to study the effect of the friction coefficient on the thermomechanical history. Results showed that contact conditions at the workpiece/tool interface have a strong effect on relative amounts of heat generated by friction and by plastic deformation. The comparison with the experimental torque applied by the tool for different rotational speeds has shown that the friction coefficient decreases when the rotational speed increases. Consequently, heat generation is far more important near the material/tool interface and the material deformation is shallower, increasing the lack of penetration probability. The variation of thermomechanical conditions with regards to the rotational speed is responsible for the variation of the nugget shape, as recrystallization conditions are not reached in the same volume of material. The second part of the research project was dedicated to a characterization of the welded joints microstructure and mechanical properties. Sound joints were obtained by using a manufacturing procedure involving process parameters optimization and quality control of the joint integrity. Five different combinations of rotational and advancing speeds were studied. Microstructure observations have shown that the rotational speed has an effect on recrystallization conditions because of the variation of the contact conditions at the material/tool interface. On the other hand, the advancing speed has a strong effect on the precipitation state in the heat affected zone (HAZ). The heat input increases when the advancing speed decreases. The material softening in the HAZ is then more pronounced. Mechanical testing of the welded joints showed that the fatigue resistance increases when the rotational speed increases and the advancing speed decreases. The fatigue resistance of FSW joints mainly depends on the ratio of the advancing speed on the rotational speed, called the welding pitch k. When the welding pitch is high (k ≥ 0,66 mm/rev), the fatigue resistance depends on crack initiation at the root of circular grooves left by the tool on the weld surface. The size of these grooves is directly related to the welding pitch. When the welding pitch is low (k ≤ 0,2 mm/rev), the heat input is high and the fatigue resistance is limited by the HAZ softening. The fatigue resistance is optimized when k stands in the 0,25-0,30 mm/rev range. Outside that range, the presence of small lateral lips is critical. The results of the characterization part of the project showed that the effects of the applied vertical force on the formation of lateral lips should be submitted to further investigations. The elimination of the lateral lip, which could be achieved with a more precise adjustment of the vertical force, could lead to an improved fatigue resistance. The elimination of lateral lips, but also the circular grooves left by the tool, may be obtained by developing an appropriate surfacing technique and could lead to an improved fatigue resistance without reducing the advancing speed. (Abstract shortened by UMI.)

  10. Lightning Protection for Explosive Facilities

    SciTech Connect

    Ong, M

    2001-12-01

    Lawrence Livermore National Laboratory funds construction of lightning protection systems to protect explosive processing and storage facilities. This paper provides an intuitive understanding of the lighting risks and types of lightning protection available. Managers can use this information to decide if limited funds should be spent constructing a lightning protection system for their own facilities. This paper answers the following questions: (1) Why do you need lightning protection systems? (2) How do lightning protection systems work? and (3) Why are there no documented cases of lightning problems at existing explosive facilities?

  11. Explosive coalescence of magnetic islands

    NASA Technical Reports Server (NTRS)

    Tajima, T.; Sakai, J.-I.

    1986-01-01

    Simulation results from both the EM collisionless particle code and the MHD particle code reveal an explosive reconnection process associated with nonlinear evolution of the coalescence instability. The explosive coalescence is a self-similar process of magnetic collapse, and ensuing amplitude oscillations in the magnetic and electrostatic energies and temperatures are modeled by an equation of motion for the scale factor in the Sagdeev potential. This phenomenon may explain the rapid energy release of a certain class of solar flares during their impulsive phase.

  12. Intravesical explosion during transurethral electrosurgery.

    PubMed

    Georgios, Kallinikas; Evangelos, Boulinakis; Helai, Habib; Ioannis, Gerzelis

    2015-05-01

    Intravesical explosion is a very rare complication of transurethral resection of prostate and transurethral resection of bladder tumour operations. In vitro studies have shown that the gases produced during the procedure could result in a blast once they are mixed with air from the atmosphere. A 79-year-old male experienced an explosion in his bladder while undergoing a transurethral resection of bladder tumour. The case is presented as well as the way that it was treated as an emergency. Precautions of such events are finally suggested. PMID:25680867

  13. Nonequilibrium detonation of composite explosives

    SciTech Connect

    Nichols III, A.L.

    1997-07-01

    The effect of nonequilibrium diffusional flow on detonation velocities in composite explosives is examined. Detonation conditions are derived for complete equilibrium, temperature and pressure equilibrium, and two forms of pressure equilibrium. Partial equilibria are associated with systems which have not had sufficient time for transport to smooth out the gradients between spatially separate regions. The nonequilibrium detonation conditions are implemented in the CHEQ equation of state code. We show that the detonation velocity decreases as the non-chemical degrees of freedom of the explosive are allowed to equilibrate. It is only when the chemical degrees of freedom are allowed to equilibrate that the detonation velocity increases.

  14. Amputation des quatre membres

    PubMed Central

    Feruzi, Maruis Kitembo; Milindi, Cédrick Sangwa; Zabibu, Mireille Kakinga; Mulefu, Jules Panda; Katombe, Francois Tshilombo

    2014-01-01

    Les auteurs présentent les cas d'amputation des quatre membres réalisée chez trois patients différents. Ce sont des amputations réalisées pour chaque patient au cours d'une seule hospitalisation et en un seul temps opératoire. Deux patients pour gangrène sèche infectée et un pour amputation traumatique des quatre membres. L'amputation d'urgence a été pratiquée en premier temps suivie de remodelage des moignons d'amputation en second temps. L’évolution de tous les patients a été bonne. PMID:25469177

  15. A follow-up study on the physique, body composition, physical fitness, and isokinetic strength of female collegiate Taekwondo athletes

    PubMed Central

    Kim, Hyun-Bae; Jung, Hyun-Chul; Song, Jong-Kook; Chai, Joo-Hee; Lee, Eun-Jae

    2015-01-01

    The purpose of the study was to analyze changes in physique, body composition, physical fitness, and isokinetic strength in female collegiate taekwondo athletes. The study included 14 subjects, of whom 8 were followed up throughout the study. Anthropometric characteristics included body weight, height, sitting height, circumferences, and bone width. Physical fitness parameters included flexibility, agility, muscle strength, muscular endurance, power, speed, and cardiorespiratory endurance. Peak torque, mean power, and H/Q ratio were analyzed by using Cybex 770. All data were analyzed by using the SAS statistical program. Paired t test was performed, with 0.05 as the significance level. The results indicated significant changes in body weight, and upper arm and flexed upper arm circumferences during the experimental period. Test scores for plate tapping, and sit and reach significantly increased, but that for power decreased. In addition, the peak power of right flexion at 180°/sec was significantly increased, as well as the mean power of right and left flexion, and the H/Q ratio at 180°/sec. PMID:25830145

  16. Prompt detonation of secondary explosives by laser

    SciTech Connect

    Paisley, D.L.

    1989-01-01

    Secondary high explosives have been promptly detonated by directing a laser beam of various wavelengths from 266 nanometers to 1.06 micron on the surface of the explosives. For this paper ''prompt'' means the excess transit time through an explosive charge is /approximately/250 nanoseconds (or less) less than the accepted full detonation velocity time. Timing between laser pulse, explosive initiation and detonation velocity and function time have been recorded. The laser parameters studied include: wavelength, pulse length, energy and power density, and beam diameter (spot size). Explosives evaluated include: PETN, HNS, HMX, and graphited PETN, HNS, and HMX. Explosive parameters that have been correlated with optical parameters include: density, surface area, critical diameter (spot size), spectral characteristics and enhance absorption. Some explosives have been promptly detonated over the entire range of wavelengths, possibly by two competing initiating mechanisms. Other explosives could not be detonated at any of the wavelengths or power densities tested. 8 refs., 12 figs., 1 tab.

  17. 49 CFR 173.54 - Forbidden explosives.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... loaded firearm (except as provided in 49 CFR 1544.219). (g) Fireworks that combine an explosive and a..., black antimony (antimony sulfide), and sulfur, if the weight of the explosive material in the...

  18. 49 CFR 173.54 - Forbidden explosives.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... loaded firearm (except as provided in 49 CFR 1544.219). (g) Fireworks that combine an explosive and a..., black antimony (antimony sulfide), and sulfur, if the weight of the explosive material in the...

  19. 49 CFR 173.54 - Forbidden explosives.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... loaded firearm (except as provided in 49 CFR 1544.219). (g) Fireworks that combine an explosive and a..., black antimony (antimony sulfide), and sulfur, if the weight of the explosive material in the...

  20. Detonation wave profiles in HMX based explosives

    SciTech Connect

    Gustavsen, R.L.; Sheffield, S.A.; Alcon, R.R.

    1997-11-01

    Detonation wave profiles have been measured in several HMX based plastic bonded explosives including PBX9404, PBX9501, and EDC-37, as well as two HMX powders (coarse and fine) pressed to 65% of crystal density. The powders had 120 and 10 {micro}m average grain sizes, respectively. Planar detonations were produced by impacting the explosive with projectiles launched in a 72-mm bore gas gun. Impactors, impact velocity, and explosive thickness were chosen so that the run distance to detonation was always less than half the explosive thickness. For the high density plastic bonded explosives, particle velocity wave profiles were measured at an explosive/window interface using two VISAR interferometers. PMMA windows with vapor deposited aluminum mirrors were used for all experiments. Wave profiles for the powdered explosives were measured using magnetic particle velocity gauges. Estimates of the reaction zone parameters were obtained from the profiles using Hugoniots of the explosive and window.

  1. Sandia Explosive Inventory and Information System

    SciTech Connect

    Clements, D.A.

    1994-08-01

    The Explosive Inventory and Information System (EIS) is being developed and implemented by Sandia National Laboratories (SNL) to incorporate a cradle to grave structure for all explosives and explosive containing devices and assemblies at SNL from acquisition through use, storage, reapplication, transfer or disposal. The system does more than track all material inventories. It provides information on material composition, characteristics, shipping requirements; life cycle cost information, plan of use; and duration of ownership. The system also provides for following the processes of explosive development; storage review; justification for retention; Resource, Recovery and Disposition Account (RRDA); disassembly and assembly; and job description, hazard analysis and training requirements for all locations and employees involved with explosive operations. In addition, other information systems will be provided through the system such as the Department of Energy (DOE) and SNL Explosive Safety manuals, the Navy`s Department of Defense (DoD) Explosive information system, and the Lawrence Livermore National Laboratories (LLNL) Handbook of Explosives.

  2. Risperidone and Explosive Aggressive Autism.

    ERIC Educational Resources Information Center

    Horrigan, Joseph P.; Barnhill, L. Jarrett

    1997-01-01

    In this study, 11 males with autism and mental retardation were administered risperidone. Substantial clinical improvement was noted almost immediately; patients with aggression, self-injury, explosivity, and poor sleep hygiene were most improved. The modal dose for optimal response was 0.5 mg bid. Weight gain was a significant side effect.…

  3. Mound calorimetry for explosive surveillance

    SciTech Connect

    Shockey, G.C.; Rodenburg, W.W.

    1985-01-01

    Heat of reaction determinations of pyrotechnics and explosives is made at MRC-Mound by bomb calorimetry. Energy releases from ten calories to 94 kilocalories have been measured accurately using four different calorimeter systems. Each system is described and some heat of reaction results are given. 3 figs., 4 tabs.

  4. Measuring explosive non-ideality

    SciTech Connect

    Souers, P C

    1999-02-17

    The sonic reaction zone length may be measured by four methods: (1) size effect, (2) detonation front curvature, (3) crystal interface velocity and (4) in-situ gauges. The amount of data decreases exponentially from (1) to (4) with there being almost no gauge data for prompt detonation at steady state. The ease and clarity of obtaining the reaction zone length increases from (1) to (4). The method of getting the reaction zone length, , is described for the four methods. A measure of non-ideality is proposed: the reaction zone length divided by the cylinder radius. N = /R{sub o}. N = 0 for true ideality. It also decreases with increasing radius as it should. For N < 0.10, an equilibrium EOS like the JWL may be used. For N > 0.10, a time-dependent description is essential. The crystal experiment, which measures the particle velocity of an explosive-transparent material interface, is presently rising in importance. We examine the data from three experiments and apply: (1) an impedance correction that transfers the explosive C-J particle velocity to the corresponding value for the interface, and (2) multiplies the interface time by 3/4 to simulate the explosive speed of sound. The result is a reaction zone length comparable to those obtained by other means. A few explosives have reaction zones so small that the change of slope in the particle velocity is easily seen.

  5. Lead-free primary explosives

    DOEpatents

    Huynh, My Hang V.

    2010-06-22

    Lead-free primary explosives of the formula (cat).sub.Y[M.sup.II(T).sub.X(H.sub.2O).sub.6-X].sub.Z, where T is 5-nitrotetrazolate, and syntheses thereof are described. Substantially stoichiometric equivalents of the reactants lead to high yields of pure compositions thereby avoiding dangerous purification steps.

  6. Turbulent Combustion in SDF Explosions

    SciTech Connect

    Kuhl, A L; Bell, J B; Beckner, V E

    2009-11-12

    A heterogeneous continuum model is proposed to describe the dispersion and combustion of an aluminum particle cloud in an explosion. It combines the gas-dynamic conservation laws for the gas phase with a continuum model for the dispersed phase, as formulated by Nigmatulin. Inter-phase mass, momentum and energy exchange are prescribed by phenomenological models. It incorporates a combustion model based on the mass conservation laws for fuel, air and products; source/sink terms are treated in the fast-chemistry limit appropriate for such gasdynamic fields, along with a model for mass transfer from the particle phase to the gas. The model takes into account both the afterburning of the detonation products of the C-4 booster with air, and the combustion of the Al particles with air. The model equations were integrated by high-order Godunov schemes for both the gas and particle phases. Numerical simulations of the explosion fields from 1.5-g Shock-Dispersed-Fuel (SDF) charge in a 6.6 liter calorimeter were used to validate the combustion model. Then the model was applied to 10-kg Al-SDF explosions in a an unconfined height-of-burst explosion. Computed pressure histories are compared with measured waveforms. Differences are caused by physical-chemical kinetic effects of particle combustion which induce ignition delays in the initial reactive blast wave and quenching of reactions at late times. Current simulations give initial insights into such modeling issues.

  7. Numerical Simulations of Thermobaric Explosions

    SciTech Connect

    Kuhl, A L; Bell, J B; Beckner, V E; Khasainov, B

    2007-05-04

    A Model of the energy evolution in thermobaric explosions is presented. It is based on the two-phase formulation: conservation laws for the gas and particle phases along with inter-phase interaction terms. It incorporates a Combustion Model based on the mass conservation laws for fuel, air and products; source/sink terms are treated in the fast-chemistry limit appropriate for such gas dynamic fields. The Model takes into account both the afterburning of the detonation products of the booster with air, and the combustion of the fuel (Al or TNT detonation products) with air. Numerical simulations were performed for 1.5-g thermobaric explosions in five different chambers (volumes ranging from 6.6 to 40 liters and length-to-diameter ratios from 1 to 12.5). Computed pressure waveforms were very similar to measured waveforms in all cases - thereby proving that the Model correctly predicts the energy evolution in such explosions. The computed global fuel consumption {mu}(t) behaved as an exponential life function. Its derivative {dot {mu}}(t) represents the global rate of fuel consumption. It depends on the rate of turbulent mixing which controls the rate of energy release in thermobaric explosions.

  8. Anomalous electrodynamic explosions in liquids

    SciTech Connect

    Aspden, H.

    1986-06-01

    The recently reported Graneau experiments on electrodynamic explosions in liquids, which reveal anomalous longitudinal electrodynamic forces of the order of 10/sup 4/ times greater than expected, verify the need for a term in the law of electrodynamics that corresponds to the ion/electron mass ratio. This confirms an earlier theoretical interpretation of the anomalous cathode reaction forces found in the vacuum arc.

  9. Explosion welding and cutting in aerospace engineering

    NASA Astrophysics Data System (ADS)

    Volgin, L. A.; Koroteev, A. Ia.; Malakovich, A. P.; Petushkov, V. G.; Sitalo, V. G.; Novikov, V. K.

    The paper presents the results of works of the E.O. Paton Electric Welding Institute and other Soviet organizations on the development of technology for explosion-welding of multilayer transition pieces and pipes used in the manufacture of aerospace products. Equipment and accessories used for this technology are described; in particular, a powerful explosion chamber of a tubular structure for up to 200 kg of explosives is presented. Information is also given about linear explosion separation devices.

  10. Shock response of several plastic bonded explosives

    SciTech Connect

    Sutherland, G.T.; Ashwell, K.D.; OConnor, J.H.; Baker, R.N.; Lemar, E.R.

    1996-05-01

    Multiple {ital in situ} manganin gauge experiments were performed on explosive compositions IRX-1, IRX-3A, PBXN-111 (PBXW-115), and PBXN-110 (PBXW-113). For most explosives, stress-time profiles show substantial reaction. These profiles are compared to those measured in other explosives and plans are discussed for future reactive rate modeling involving these explosives. {copyright} {ital 1996 American Institute of Physics.}

  11. Explosives for Lunar Seismic Profiling Experiment (LSPE)

    NASA Technical Reports Server (NTRS)

    1973-01-01

    Explosive charges of various sizes were investigated for use in lunar seismic studies. Program logistics, and the specifications for procurement of bulk explosives are described. The differential analysis, thermal properties, and detonation velocity measurements on HNS/Teflon 7C 90/10 are reported along with the field tests of the hardware. It is concluded that nearly all large explosive charges crack after fabrication, from aging or thermal shock. The cracks do not affect the safety, or reliability of the explosives.

  12. 77 FR 58410 - Commerce in Explosives; List of Explosive Materials (2012R-10T)

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-09-20

    ..., 76 FR 64974). Notice of List of Explosive Materials Pursuant to 18 U.S.C. 841(d) and 27 CFR 555.23, I... of Alcohol, Tobacco, Firearms, and Explosives Commerce in Explosives; List of Explosive Materials.... Display fireworks. DNPA . DNPD . Dynamite. E EDDN . EDNA . Ednatol. EDNP . EGDN . Erythritol...

  13. 75 FR 70291 - Commerce in Explosives; List of Explosive Materials (2010R-27T)

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-11-17

    ..., 75 FR 1085). Notice of List of Explosive Materials Pursuant to 18 U.S.C. 841(d) and 27 CFR 555.23, I... of Alcohol, Tobacco, Firearms and Explosives Commerce in Explosives; List of Explosive Materials.... Display fireworks. DNPA . DNPD . Dynamite. E EDDN . EDNA . Ednatol. EDNP . EGDN . Erythritol...

  14. 76 FR 64974 - Commerce in Explosives; List of Explosive Materials (2011R-18T)

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-10-19

    ... Explosive Materials dated November 17, 2010 (Docket No. ATF 42N, 75 FR 70291). Notice of List of Explosive.... BEAF . Black powder. Black powder based explosive mixtures. * Blasting agents, nitro-carbo-nitrates... powder. BTNEC . BTNEN . BTTN . Bulk salutes. Butyl tetryl. C Calcium nitrate explosive mixture....

  15. Transuranic drum hydrogen explosion tests

    SciTech Connect

    Dykes, K.L.; Meyer, M.L.

    1991-06-01

    Radiolysis of transuranic (TRU) waste can produce flammable ({gt}4%) mixtures of hydrogen gas in 55 gallon vented waste storage drums. Explosion testing was conducted at the E. I. duPont Explosion Hazards Laboratory to determine the minimum concentration at which a drum lid removal occurs. A secondary objective was to investigate the maximum pressure and rate of pressure rise as a function of hydrogen concentration. Prior to beginning any drum explosion tests, small-scale pressure vessel tests and drum mixing tests were completed. The pressure vessel tests established a relationship between hydrogen concentration and the maximum pressure and pressure rise. These small-scale tests were used to establish the concentration range over which a drum lid removal might occur. Mixing tests were also conducted to determine the equilibration times for two different hydrogen-air mixtures in a TRU drum. Nine successful drum explosion tests were conducted over a hydrogen concentration range of 13--36% (v/v), test results suggest total integrity failure via drum lid removal will not occur below 15% (v/v). Controlled small-scale pressure vessel tests were conducted over a range of 5--50% (v/v) to determine the pressure and pressure rise as a function of hydrogen concentration. No similar relationship could be established for the drum explosion tests due to the variability in drum lid sealing and retaining ring closure. Mixing tests conducted at 5% and 25% (v/v) indicate adding pure hydrogen to the middle of a drum causes some initial stratification along the drum length, but the air and hydrogen become well-mixed after 50 minutes. 4 refs., 11 figs., 2 tabs.

  16. 46 CFR 153.921 - Explosives.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 5 2012-10-01 2012-10-01 false Explosives. 153.921 Section 153.921 Shipping COAST GUARD....921 Explosives. No person may load, off-load, or carry a cargo listed in this part on board a vessel that carries explosives unless he has the prior written permission of the Commandant (CG-ENG)....

  17. 14 CFR 420.63 - Explosive siting.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 14 Aeronautics and Space 4 2012-01-01 2012-01-01 false Explosive siting. 420.63 Section 420.63... TRANSPORTATION LICENSING LICENSE TO OPERATE A LAUNCH SITE Responsibilities of a Licensee § 420.63 Explosive... the configuration of the launch site is in accordance with an explosive site plan, and that...

  18. 46 CFR 188.10-25 - Explosive.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... release of gas and heat. Explosives are discussed in more detail in 49 CFR parts 171-179. ... 46 Shipping 7 2012-10-01 2012-10-01 false Explosive. 188.10-25 Section 188.10-25 Shipping COAST... Definition of Terms Used in This Subchapter § 188.10-25 Explosive. This term means a chemical compound...

  19. 33 CFR 401.67 - Explosive vessels.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 33 Navigation and Navigable Waters 3 2012-07-01 2012-07-01 false Explosive vessels. 401.67 Section... TRANSPORTATION SEAWAY REGULATIONS AND RULES Regulations Dangerous Cargo § 401.67 Explosive vessels. A vessel carrying explosives, either Government or commercial, as defined in the Dangerous Cargo Act of the...

  20. Analysis of Picattiny Sample for Trace Explosives

    SciTech Connect

    Klunder, G; Whipple, R; Carman, L; Spackman, P E; Reynolds, J; Alcaraz, A

    2008-05-23

    The sample received from Picatinny Arsenal was analyzed for trace amounts of high explosives (HE). A complete wash of the surface was performed, concentrated, and analyzed using two sensitive analysis techniques that are capable of detecting numerous types of explosives. No explosives were detected with either test.

  1. Explosive detection program at Sandia National Laboratories

    SciTech Connect

    Conrad, F.J.

    1983-01-01

    A brief, general description of the Explosive Detection Program at Sandia National Laboratories is given. The six major topics of the program are: (1) Coated or Uncoated Metallic Preconcentrators; (2) a Derivatization Study; (3) a Portable Ion Mobility Spectrometer; (4) an Explosive Screening Portal; (5) Mass Spectrometer Development; and (6) an Explosive Vapor Generator.

  2. 46 CFR 153.921 - Explosives.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 5 2013-10-01 2013-10-01 false Explosives. 153.921 Section 153.921 Shipping COAST GUARD....921 Explosives. No person may load, off-load, or carry a cargo listed in this part on board a vessel that carries explosives unless he has the prior written permission of the Commandant (CG-ENG)....

  3. 46 CFR 188.10-25 - Explosive.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... release of gas and heat. Explosives are discussed in more detail in 49 CFR parts 171-179. ... 46 Shipping 7 2011-10-01 2011-10-01 false Explosive. 188.10-25 Section 188.10-25 Shipping COAST... Definition of Terms Used in This Subchapter § 188.10-25 Explosive. This term means a chemical compound...

  4. 46 CFR 188.10-25 - Explosive.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... release of gas and heat. Explosives are discussed in more detail in 49 CFR parts 171-179. ... 46 Shipping 7 2013-10-01 2013-10-01 false Explosive. 188.10-25 Section 188.10-25 Shipping COAST... Definition of Terms Used in This Subchapter § 188.10-25 Explosive. This term means a chemical compound...

  5. 33 CFR 401.67 - Explosive vessels.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Explosive vessels. 401.67 Section... TRANSPORTATION SEAWAY REGULATIONS AND RULES Regulations Dangerous Cargo § 401.67 Explosive vessels. A vessel carrying explosives, either Government or commercial, as defined in the Dangerous Cargo Act of the...

  6. 46 CFR 153.921 - Explosives.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 5 2011-10-01 2011-10-01 false Explosives. 153.921 Section 153.921 Shipping COAST GUARD....921 Explosives. No person may load, off-load, or carry a cargo listed in this part on board a vessel that carries explosives unless he has the prior written permission of the Commandant (CG-522)....

  7. 14 CFR 420.63 - Explosive siting.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 4 2011-01-01 2011-01-01 false Explosive siting. 420.63 Section 420.63... TRANSPORTATION LICENSING LICENSE TO OPERATE A LAUNCH SITE Responsibilities of a Licensee § 420.63 Explosive... the configuration of the launch site is in accordance with an explosive site plan, and that...

  8. 33 CFR 401.67 - Explosive vessels.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 33 Navigation and Navigable Waters 3 2013-07-01 2013-07-01 false Explosive vessels. 401.67 Section... TRANSPORTATION SEAWAY REGULATIONS AND RULES Regulations Dangerous Cargo § 401.67 Explosive vessels. A vessel carrying explosives, either Government or commercial, as defined in the Dangerous Cargo Act of the...

  9. 14 CFR 420.63 - Explosive siting.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Explosive siting. 420.63 Section 420.63... TRANSPORTATION LICENSING LICENSE TO OPERATE A LAUNCH SITE Responsibilities of a Licensee § 420.63 Explosive... the configuration of the launch site is in accordance with an explosive site plan, and that...

  10. 46 CFR 188.10-25 - Explosive.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... release of gas and heat. Explosives are discussed in more detail in 49 CFR parts 171-179. ... 46 Shipping 7 2010-10-01 2010-10-01 false Explosive. 188.10-25 Section 188.10-25 Shipping COAST... Definition of Terms Used in This Subchapter § 188.10-25 Explosive. This term means a chemical compound...

  11. 33 CFR 401.67 - Explosive vessels.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 33 Navigation and Navigable Waters 3 2011-07-01 2011-07-01 false Explosive vessels. 401.67 Section... TRANSPORTATION SEAWAY REGULATIONS AND RULES Regulations Dangerous Cargo § 401.67 Explosive vessels. A vessel carrying explosives, either Government or commercial, as defined in the Dangerous Cargo Act of the...

  12. 46 CFR 153.921 - Explosives.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Explosives. 153.921 Section 153.921 Shipping COAST GUARD....921 Explosives. No person may load, off-load, or carry a cargo listed in this part on board a vessel that carries explosives unless he has the prior written permission of the Commandant (CG-522)....

  13. 33 CFR 401.67 - Explosive vessels.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 33 Navigation and Navigable Waters 3 2014-07-01 2014-07-01 false Explosive vessels. 401.67 Section... TRANSPORTATION SEAWAY REGULATIONS AND RULES Regulations Dangerous Cargo § 401.67 Explosive vessels. A vessel carrying explosives, either Government or commercial, as defined in the Dangerous Cargo Act of the...

  14. 46 CFR 188.10-25 - Explosive.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... release of gas and heat. Explosives are discussed in more detail in 49 CFR parts 171-179. ... 46 Shipping 7 2014-10-01 2014-10-01 false Explosive. 188.10-25 Section 188.10-25 Shipping COAST... Definition of Terms Used in This Subchapter § 188.10-25 Explosive. This term means a chemical compound...

  15. 46 CFR 153.921 - Explosives.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 5 2014-10-01 2014-10-01 false Explosives. 153.921 Section 153.921 Shipping COAST GUARD....921 Explosives. No person may load, off-load, or carry a cargo listed in this part on board a vessel that carries explosives unless he has the prior written permission of the Commandant (CG-ENG)....

  16. Thermally stable, plastic-bonded explosives

    DOEpatents

    Benziger, Theodore M.

    1979-01-01

    By use of an appropriate thermoplastic rubber as the binder, the thermal stability and thermal stress characteristics of plastic-bonded explosives may be greatly improved. In particular, an HMX-based explosive composition using an oil-extended styrene-ethylenebutylene-styrene block copolymer as the binder exhibits high explosive energy and thermal stability and good handling safety and physical properties.

  17. Doping explosive materials for neutron radiographic enhancement.

    NASA Technical Reports Server (NTRS)

    Golliher, K. G.

    1971-01-01

    Discussion of studies relating to the selection of doping materials of high neutron absorption usable for enhancing the neutron radiographic imaging of explosive mixtures, without interfering with the proper chemical reaction of the explosives. The results of the studies show that gadolinium oxide is an excellent material for doping explosive mixtures to enhance the neutron radiographic image.

  18. Restauration fonctionnelle du rachis : effet du niveau initial de douleur sur les performances des sujets lombalgiques chroniques

    PubMed Central

    Caby, Isabelle; Olivier, N; Mendelek, F; Kheir, R Bou; Vanvelcenaher, J; Pelayo, P

    2014-01-01

    HISTORIQUE : La lombalgie chronique est une douleur lombaire persistante d’origine multifactorielle. Le niveau de douleur initial reste faiblement utilisé pour analyser et comparer les réponses des patients lombalgiques au programme de reconditionnement. OBJECTIFS : Apprécier et évaluer les réponses des sujets lombalgiques chroniques très douloureux à une prise en charge dynamique et intensive. MÉTHODOLOGIE : 144 sujets atteints de lombalgie chronique ont été inclus dans un programme de restauration fonctionnelle du rachis de 5 semaines. Les sujets ont été classés en deux groupes de niveau de douleur: un groupe atteint de douleur sévère (n = 28) et un groupe atteint de douleur légère à modérée (n = 106). L’ensemble des sujets ont bénéficié d’une prise en charge identique comprenant principalement de la kinésithérapie, de l’ergothérapie, du reconditionnement musculaire et cardio-vasculaire ainsi qu’un suivi psychologique. Les paramètres physiques (flexibilité, force musculaire) et psychologiques (qualité de vie) ont été mesurés avant (T0) et après le programme (T5sem). RÉSULTATS : L’ensemble des performances physiques et fonctionnelles des sujets très douloureux sont moins bonnes et le retentissement de la lombalgie sur la qualité de vie, pour ces mêmes sujets, est majoré à T0. Toutes les différences significatives constatées à T0 entre les deux groupes s’effacent à T5sem. CONCLUSIONS : Les sujets lombalgiques chroniques très douloureux répondent favorablement au programme dynamique et intensif. L’intensité douloureuse de la lombalgie n’aurait pas d’effet sur les réponses au programme. La restauration fonctionnelle du rachis apporterait aux sujets la possibilité de mieux gérer leur douleur quel que soit son niveau. PMID:25299476

  19. 27 CFR 555.205 - Movement of explosive materials.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2012-04-01 2010-04-01 true Movement of explosive..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Storage § 555.205 Movement of explosive materials. All explosive materials must be kept in locked magazines meeting...

  20. 27 CFR 555.109 - Identification of explosive materials.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2012-04-01 2010-04-01 true Identification of explosive..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Conduct of Business or Operations § 555.109 Identification of explosive materials. (a) General. Explosive materials,...

  1. 27 CFR 555.32 - Special explosive devices.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2012-04-01 2010-04-01 true Special explosive devices..., AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Administrative and Miscellaneous Provisions § 555.32 Special explosive devices. The Director may exempt certain explosive...

  2. 27 CFR 555.109 - Identification of explosive materials.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2011-04-01 2010-04-01 true Identification of explosive..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Conduct of Business or Operations § 555.109 Identification of explosive materials. (a) General. Explosive materials,...

  3. 27 CFR 555.205 - Movement of explosive materials.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2011-04-01 2010-04-01 true Movement of explosive..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Storage § 555.205 Movement of explosive materials. All explosive materials must be kept in locked magazines meeting...

  4. 27 CFR 555.205 - Movement of explosive materials.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2010-04-01 2010-04-01 false Movement of explosive..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Storage § 555.205 Movement of explosive materials. All explosive materials must be kept in locked magazines meeting...

  5. 27 CFR 555.32 - Special explosive devices.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2010-04-01 2010-04-01 false Special explosive devices..., AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Administrative and Miscellaneous Provisions § 555.32 Special explosive devices. The Director may exempt certain explosive...

  6. 27 CFR 555.109 - Identification of explosive materials.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... explosive materials. 555.109 Section 555.109 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Conduct of Business or Operations § 555.109 Identification of explosive materials. (a) General. Explosive...

  7. 27 CFR 555.205 - Movement of explosive materials.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2013-04-01 2013-04-01 false Movement of explosive..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Storage § 555.205 Movement of explosive materials. All explosive materials must be kept in locked magazines meeting...

  8. 27 CFR 555.32 - Special explosive devices.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2013-04-01 2013-04-01 false Special explosive devices..., AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Administrative and Miscellaneous Provisions § 555.32 Special explosive devices. The Director may exempt certain explosive...

  9. 27 CFR 555.32 - Special explosive devices.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2011-04-01 2010-04-01 true Special explosive devices..., AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Administrative and Miscellaneous Provisions § 555.32 Special explosive devices. The Director may exempt certain explosive...

  10. 27 CFR 555.32 - Special explosive devices.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2014-04-01 2014-04-01 false Special explosive devices..., AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Administrative and Miscellaneous Provisions § 555.32 Special explosive devices. The Director may exempt certain explosive...

  11. 27 CFR 555.109 - Identification of explosive materials.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... explosive materials. 555.109 Section 555.109 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Conduct of Business or Operations § 555.109 Identification of explosive materials. (a) General. Explosive...

  12. 27 CFR 555.205 - Movement of explosive materials.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2014-04-01 2014-04-01 false Movement of explosive..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Storage § 555.205 Movement of explosive materials. All explosive materials must be kept in locked magazines meeting...

  13. Modélisation des charges d'espace dans les isolants solides par une analyse spectrale

    NASA Astrophysics Data System (ADS)

    Haas, V.; Scouarnec, Ch.; Franceschi, J. L.

    1998-01-01

    A mathematical method based on spectral algebra is developped for the thermal modulation method. These methods permit to measure the space charge distribution in solid insulators. The modelling presented permits to evaluate the performances and the limitations of the measurement method. Une linéarisation par l'algèbre spectrale a été développée dans une méthode de modulation thermique pour mesurer la distribution des charges électriques dans les isolants solides. La modélisation présentée permet d'évaluer les performances et les limites tant numériques que physiques de la méthode de mesure.

  14. Explosive events on the Sun.

    PubMed

    Harra, Louise K

    2002-12-15

    I describe two of the most dynamic and highly energetic phenomena in the Solar System--the explosive flares that can occur when plasma is confined by magnetic fields and the large-scale ejections of material known as 'coronal mass ejections'. These explosive events are poorly understood and yet occur in a variety of contexts in the Universe, ranging from planetary magnetospheres to active galactic nuclei. Understanding why flares and coronal mass ejections occur is a major goal across a wide range of space physics and astrophysics. Although explosive events from the Sun have dramatic effects on Earth, flares in other stars, for example, can be vastly more energetic and have an even more profound effect on their environment. We are now in the unprecedented position of having access to a number of space observatories dedicated to the Sun: the Yohkoh spacecraft, the Solar and Heliospheric Observatory, the Transition Region and Coronal Explorer and the Ramaty High Energy Solar Spectroscopic Imager. These cover a wide wavelength range from white light to gamma rays with both spectroscopy and imaging, and allow huge progress to be made in understanding the processes involved in such large explosions. The high-resolution data show dramatic and complex explosions of material on all spatial scales on the Sun. They have revealed that the Sun is constantly changing everywhere on its surface--something that was never imagined before. One of the mechanisms that has been proposed to account for the large energy release is magnetic reconnection. Recent observations from space increasingly support this view. This article will discuss those observations that support this model and also those that suggest different processes. The current space missions have given us an excellent insight into the actual explosive processes in the Sun. However, they have provided us with only a tantalizing glimpse of what causes the elusive trigger. Future missions such as Solar-B (the follow-on to

  15. Explosive shocks in air (2nd edition)

    NASA Astrophysics Data System (ADS)

    Kinney, G. F.; Graham, K. J.

    After an initial qualitative characterization of the properties of explosions in the atmosphere and their blast and shock propagation effects, attention is given to the underlying quantitative principles of explosive energy release, including the scaling laws for explosions and internal blast effects from confined explosions. The dynamic loads that blast waves impose on representative structures are then characterized, with attention to resulting structural damage. A major feature of the present treatment is the use of the dimensionless Mach number in all shock equations; a further simplification is furnished by first developing mathematical equations for shock in steady flow, and then applying these equations to explosive shock by simple transformation of coordinates.

  16. Methodes non perturbatives en mecanique quantique et en theorie des champs quantiques

    NASA Astrophysics Data System (ADS)

    Jirari, Hamza

    2001-10-01

    Nous construisons un hamiltonien effectif à partir de l'intégrale de chemin via la méthode Monte-Carlo. Cet hamiltonien décrit les phénomènes physiques dans le domaine de basse énergie. Nous déterminons le spectre d'énergie et les fonctions d'ondes de plusieurs systèmes quantiques. Les résultats obtenus montrent que cette nouvelle approche Monte-Carlo hamiltonienne fonctionne. En mécanique quantique, nous suggérons une expression analytique de l'intégrale de chemin en introduisant une action quantique avec des paramètres renormalisés. Nous présentons des résultats numériques pour quelques potentiels locaux. Cette action quantique offre la possibilité de comparer l'évolution classique et quantique et permet de quantifier les instantons classiques et éventuellement le chaos classique. Nous investiguons la QCD sur un réseau bidimensionnel en utilisant une version améliorée des fermions de Wilson. Nous montrons que la théorie améliorée conduit à une réduction significative des erreurs dues à la valeur finie du pas du réseau. Nous calculons le condensat chiral et la masse de l'état lié quark-antiquark. Nous aboutissons à une bonne concordance entre nos résultats numériques et les résultats analytiques du modèle dans le continu.

  17. Hazards of explosives dusts: Particle size effects

    SciTech Connect

    Cashdollar, K L; Hertzberg, M; Green, G M

    1992-02-01

    At the request of the Department of Energy, the Bureau of Mines has investigated the hazards of military explosives dispersed as dust clouds in a 20-L test chamber. In this report, the effect of particle size for HMX, HNS, RDX, TATB, and TNT explosives dusts is studied in detail. The explosibility data for these dusts are also compared to those for pure fuel dusts. The data show that all of the sizes of the explosives dusts that were studied were capable of sustaining explosions as dust clouds dispersed in air. The finest sizes (<10 [mu]m) of explosives dusts were less reactive than the intermediate sizes (20 to 60 [mu]m); this is opposite to the particle size effect observed previously for the pure fuel dusts. At the largest sizes studied, the explosives dusts become somewhat less reactive as dispersed dust clouds. The six sizes of the HMX dust were also studied as dust clouds dispersed in nitrogen.

  18. Spot test kit for explosives detection

    DOEpatents

    Pagoria, Philip F; Whipple, Richard E; Nunes, Peter J; Eckels, Joel Del; Reynolds, John G; Miles, Robin R; Chiarappa-Zucca, Marina L

    2014-03-11

    An explosion tester system comprising a body, a lateral flow membrane swab unit adapted to be removeably connected to the body, a first explosives detecting reagent, a first reagent holder and dispenser operatively connected to the body, the first reagent holder and dispenser containing the first explosives detecting reagent and positioned to deliver the first explosives detecting reagent to the lateral flow membrane swab unit when the lateral flow membrane swab unit is connected to the body, a second explosives detecting reagent, and a second reagent holder and dispenser operatively connected to the body, the second reagent holder and dispenser containing the second explosives detecting reagent and positioned to deliver the second explosives detecting reagent to the lateral flow membrane swab unit when the lateral flow membrane swab unit is connected to the body.

  19. Explosives detection system and method

    DOEpatents

    Reber, Edward L.; Jewell, James K.; Rohde, Kenneth W.; Seabury, Edward H.; Blackwood, Larry G.; Edwards, Andrew J.; Derr, Kurt W.

    2007-12-11

    A method of detecting explosives in a vehicle includes providing a first rack on one side of the vehicle, the rack including a neutron generator and a plurality of gamma ray detectors; providing a second rack on another side of the vehicle, the second rack including a neutron generator and a plurality of gamma ray detectors; providing a control system, remote from the first and second racks, coupled to the neutron generators and gamma ray detectors; using the control system, causing the neutron generators to generate neutrons; and performing gamma ray spectroscopy on spectra read by the gamma ray detectors to look for a signature indicative of presence of an explosive. Various apparatus and other methods are also provided.

  20. Applying NASA's explosive seam welding

    NASA Technical Reports Server (NTRS)

    Bement, Laurence J.

    1991-01-01

    The status of an explosive seam welding process, which was developed and evaluated for a wide range of metal joining opportunities, is summarized. The process employs very small quantities of explosive in a ribbon configuration to accelerate a long-length, narrow area of sheet stock into a high-velocity, angular impact against a second sheet. At impact, the oxide films of both surface are broken up and ejected by the closing angle to allow atoms to bond through the sharing of valence electrons. This cold-working process produces joints having parent metal properties, allowing a variety of joints to be fabricated that achieve full strength of the metals employed. Successful joining was accomplished in all aluminum alloys, a wide variety of iron and steel alloys, copper, brass, titanium, tantalum, zirconium, niobium, telerium, and columbium. Safety issues were addressed and are as manageable as many currently accepted joining processes.

  1. Printable sensors for explosive detonation

    SciTech Connect

    Griffith, Matthew J. Cooling, Nathan A.; Elkington, Daniel C.; Belcher, Warwick J.; Dastoor, Paul C.; Muller, Elmar

    2014-10-06

    Here, we report the development of an organic thin film transistor (OTFT) based on printable solution processed polymers and employing a quantum tunnelling composite material as a sensor to convert the pressure wave output from detonation transmission tubing (shock tube) into an inherently amplified electronic signal for explosives initiation. The organic electronic detector allows detection of the signal in a low voltage operating range, an essential feature for sites employing live ordinances that is not provided by conventional electronic devices. We show that a 30-fold change in detector response is possible using the presented detector assembly. Degradation of the OTFT response with both time and repeated voltage scans was characterised, and device lifetime is shown to be consistent with the requirements for on-site printing and usage. The integration of a low cost organic electronic detector with inexpensive shock tube transmission fuse presents attractive avenues for the development of cheap and simple assemblies for precisely timed initiation of explosive chains.

  2. Waves from an underground explosion

    NASA Astrophysics Data System (ADS)

    Krymskii, A. V.; Lyakhov, G. M.

    1984-05-01

    The problem of the propagation of a spherical detonation wave in water-saturated soil was solved in [1, 2] by using a model of a liquid porous multicomponent medium with bulk viscosity. Experiments show that soils which are not water saturated are solid porous multicomponent media having a viscosity, nonlinear bulk compression limit diagrams, and irreversible deformations. Taking account of these properties, and using the model in [2], we have solved the problem of the propagation of a spherical detonation wave from an underground explosion. The solution was obtained by computer, using the finite difference method [3]. The basic wave parameters were determined at various distances from the site of the explosion. The values obtained are in good agreement with experiment. Models of soils as viscous media which take account of the dependence of deformations on the rate of loading were proposed in [4 7] also. In [8] a model was proposed corresponding to a liquid multicomponent medium with a variable viscosity.

  3. Liquids and homemade explosive detection

    NASA Astrophysics Data System (ADS)

    Ellenbogen, Michael; Bijjani, Richard

    2009-05-01

    Excerpt from the US Transportation Security Agency website: "The ban on liquids, aerosols and gels was implemented on August 10 after a terrorist plot was foiled. Since then, experts from around the government, including the FBI and our national labs have analyzed the information we now have and have conducted extensive explosives testing to get a better understanding of this specific threat." In order to lift the ban and ease the burden on the flying public, Reveal began an extensive effort in close collaboration with the US and several other governments to help identify these threats. This effort resulted in the successful development and testing of an automated explosive detection system capable of resolving these threats with a high probability of detection and a low false alarm rate. We will present here some of the methodology and approach we took to address this problem.

  4. Elasticity of crystalline molecular explosives

    DOE PAGESBeta

    Hooks, Daniel E.; Ramos, Kyle J.; Bolme, C. A.; Cawkwell, Marc J.

    2015-04-14

    Crystalline molecular explosives are key components of engineered explosive formulations. In precision applications a high degree of consistency and predictability is desired under a range of conditions to a variety of stimuli. Prediction of behaviors from mechanical response and failure to detonation initiation and detonation performance of the material is linked to accurate knowledge of the material structure and first stage of deformation: elasticity. The elastic response of pentaerythritol tetranitrate (PETN), cyclotrimethylene trinitramine (RDX), and cyclotetramethylene tetranitramine (HMX), including aspects of material and measurement variability, and computational methods are described in detail. Experimental determinations of elastic tensors are compared, andmore » an evaluation of sources of error is presented. Furthermore, computed elastic constants are also compared for these materials and for triaminotrinitrobenzene (TATB), for which there are no measurements.« less

  5. Elasticity of crystalline molecular explosives

    SciTech Connect

    Hooks, Daniel E.; Ramos, Kyle J.; Bolme, C. A.; Cawkwell, Marc J.

    2015-04-14

    Crystalline molecular explosives are key components of engineered explosive formulations. In precision applications a high degree of consistency and predictability is desired under a range of conditions to a variety of stimuli. Prediction of behaviors from mechanical response and failure to detonation initiation and detonation performance of the material is linked to accurate knowledge of the material structure and first stage of deformation: elasticity. The elastic response of pentaerythritol tetranitrate (PETN), cyclotrimethylene trinitramine (RDX), and cyclotetramethylene tetranitramine (HMX), including aspects of material and measurement variability, and computational methods are described in detail. Experimental determinations of elastic tensors are compared, and an evaluation of sources of error is presented. Furthermore, computed elastic constants are also compared for these materials and for triaminotrinitrobenzene (TATB), for which there are no measurements.

  6. Stellar explosions, instabilities, and turbulence

    SciTech Connect

    Drake, R. P.; Kuranz, C. C.; Miles, A. R.; Muthsam, H. J.; Plewa, T.

    2009-04-15

    It has become very clear that the evolution of structure during supernovae is centrally dependent on the pre-existing structure in the star. Modeling of the pre-existing structure has advanced significantly, leading to improved understanding and to a physically based assessment of the structure that will be present when a star explodes. It remains an open question whether low-mode asymmetries in the explosion process can produce the observed effects or whether the explosion mechanism somehow produces jets of material. In any event, the workhorse processes that produce structure in an exploding star are blast-wave driven instabilities. Laboratory experiments have explored these blast-wave-driven instabilities and specifically their dependence on initial conditions. Theoretical work has shown that the relative importance of Richtmyer-Meshkov and Rayleigh-Taylor instabilities varies with the initial conditions and does so in ways that can make sense of a range of astrophysical observations.

  7. Photographic laboratory studies of explosions.

    NASA Technical Reports Server (NTRS)

    Kamel, M. M.; Oppenheim, A. K.

    1973-01-01

    Description of a series of cinematographic studies of explosions made with a high-speed rotating-mirror streak camera which uses a high-frequency stroboscopic ruby laser as the light source. The results obtained mainly concern explosions initiated by focused laser irradiation from a pulsed neodymium laser in a detonating gas consisting essentially of an equimolar mixture of acetylene and oxygen at an initial pressure of 100 torr at room temperature. Among the most significant observations were observations of a spherical blast wave preceded by a Chapman-Jouguet detonation which is stabilized immediately after initiation, the merging of a spherical flame with a shock front of the blast wave in which the flame is propagating, the division of a spherical detonation front into a shock wave and flame, and the generation of shock waves by a network of spherical flames.

  8. The entropy in supernova explosions

    SciTech Connect

    Colgate, S.A.

    1990-12-06

    The explosion of a supernova forms because of the collapse to a neutron star. In addition an explosion requires that a region of relatively high entropy be in contact with the neutron star and persisting for a relatively protracted period of time. The high entropy region ensures that the maximum temperature in contact with the neutron star and in hydrostatic equilibrium is less than some maximum. This temperature must be low enough such that neutrino emission cooling is small, otherwise the equilibrium atmosphere will collapse adding a large accretion mass to the neutron star. A so-called normal explosion shock that must reverse the accretion flow corresponding to a typical stellar collapse must have sufficient strength or pressure to reverse this flow and eject the matter with 10{sup 51} ergs for a typical type II supernova. Surprisingly the matter behind such a shock wave has a relatively low entropy low enough such that neutrino cooling would be orders of magnitude faster than the expansion rate. The resulting accretion low would be inside the Bondi radius and result in free-fall accretion inside the expanding rarefaction wave. The accreted mass or reimplosion mass unless stopped by a high entropy bubble could than exceed that of bound neutron star models. In addition the explosion shock would be overtaken by the rarefaction wave and either disappear or at least weaken. Hence, a hot, high entropy bubble is required to support an equilibrium atmosphere in contact with a relatively cold neutron star. Subsequently during the expansion of the high entropy bubble that drives or pushes on the shocked matter, mixing of the matter of the high entropy bubble and lower entropy shock-ejected matter is ensured. The mixing is driven by the negative entropy gradient between the high entropy bubble accelerating the shocked matter and the lower entropy of the matter behind the shock.

  9. Preventing large-battery explosions

    NASA Astrophysics Data System (ADS)

    Cummins, D.; Pangeri, S. F.

    1980-08-01

    This information circular presents a brief history of the lead-acid battery and describes ways to prevent serious injury from battery explosions when servicing and charging lead-acid batteries, particularly in the surface mining industry. The Mining Safety and Health Administration (MSHA), U.S. Consumer Product Safety Commission, battery maufacturers, and the mining industry have all contributed information as well as recommendations for injury-free handling for this report.

  10. Splicing Wires Permanently With Explosives

    NASA Technical Reports Server (NTRS)

    Bement, Laurence J.; Kushnick, Anne C.

    1990-01-01

    Explosive joining process developed to splice wires by enclosing and metallurgically bonding wires within copper sheets. Joints exhibit many desirable characteristics, 100-percent conductivity and strength, no heat-induced annealing, no susceptibility to corrosion in contacts between dissimilar metals, and stability at high temperature. Used to join wires to terminals, as well as to splice wires. Applicable to telecommunications industry, in which millions of small wires spliced annually.

  11. Explosive Formulation Code Naming SOP

    SciTech Connect

    Martz, H. E.

    2014-09-19

    The purpose of this SOP is to provide a procedure for giving individual HME formulations code names. A code name for an individual HME formulation consists of an explosive family code, given by the classified guide, followed by a dash, -, and a number. If the formulation requires preparation such as packing or aging, these add additional groups of symbols to the X-ray specimen name.

  12. Dynamics of Relativistic Magnetized Explosions

    NASA Astrophysics Data System (ADS)

    Lyutikov, M.

    2001-11-01

    The dynamics of (i) relativistic blast waves propagating through magnetized medium, (ii) magnetic explosions (when most energy is released in a form of toroidal magnetic field) is considered taking into account possible inhomogeneities of density and external magnetic field and additional energy supply. Self-similar solutions for the internal structure in the bulk flow and in the strongly magnetized sheath near contact discontinuity are found.

  13. Fish kill from underwater explosions

    USGS Publications Warehouse

    Stuart, David J.

    1962-01-01

    The U.S. Geological Survey has used 23 different shotpoints during two seasons of field work in our seismic study of crustal structure in western United States. Without exception, it has been found that under-water shotpoints result in a more efficient conversion of explosive energy into seismic energy than do drilled-hole shotpoints. This experience, together with elimination of drilling costs, has led to the use of underwater shotpoints wherever possible. Three of the 23 shotpoints were in the Pacific Ocean, and for these we have no detailed information on the fish kill. Another six shotpoints were located in inland bodies of water. These are: * Soda Lake near Fallon, Nevada * Mono Lake near Lee Vining, California * Lake Mead near Boulder City, Nevada * Shasta Lake near Redding, California * C.J. Strike Reservoir near Bruneau, Idaho * Lucky Peak Reservoir near Boise, Idaho The 22 high-explosive charges, weighing a total of 95,100 pounds, that were fired in lakes containing fish life resulted in the known death of 2,413 game fish with a total weight of 759 pounds. The average mortality was 110 game fish or 34.5 pounds of game fish killed per average shot of 4,325 pounds of high-explosives.

  14. Thermodynamic States in Explosion Fields

    SciTech Connect

    Kuhl, A L

    2010-03-12

    We investigate the thermodynamic states occurring in explosion fields from condensed explosive charges. These states are often modeled with a Jones-Wilkins-Lee (JWL) function. However, the JWL function is not a Fundamental Equation of Thermodynamics, and therefore cannot give a complete specification of such states. We use the Cheetah code of Fried to study the loci of states of the expanded detonation products gases from C-4 charges, and their combustion products air. In the Le Chatelier Plane of specific-internal-energy versus temperature, these loci are fit with a Quadratic Model function u(T), which has been shown to be valid for T < 3,000 K and p < 1k-bar. This model is used to derive a Fundamental Equation u(v,s) for C-4. Given u(v,s), one can use Maxwell's Relations to derive all other thermodynamic functions, such as temperature: T(v,s), pressure: p(v,s), enthalpy: h(v,s), Gibbs free energy: g(v,s) and Helmholz free energy: f(v,s); these loci are displayed in figures for C-4. Such complete equations of state are needed for numerical simulations of blast waves from explosive charges, and their reflections from surfaces.

  15. Energy transfer in solid explosives

    SciTech Connect

    Tarver, C.M.; Fried, L.E.; Ruggiero, A.J.; Calef, D.F.

    1993-07-01

    The nonequilibrium Zeldovich-von Neumann-Doring theory of detonation in solid explosives is extended to include recent nanosecond and picosecond experimental and theoretical results on each of the four main regions of the reaction zone. The first region is the three-dimensional, Mach stem dominated leading shock front which excites the phonon modes of the explosive molecules in less than a picosecond. The second region is the multiphonon up-pumping process in which the excited phonons anharmonically couple to the low frequency (doorway) vibrational modes which in turn equilibrate with the higher frequency modes by internal vibrational redistribution. This process may require on the order of tens of picoseconds. The third region is the chemical reconstitution region in which the vibrationally equilibrated transition state decomposes in a series of chain reaction steps into highly vibrationally excited diatomic and triatomic molecules in approximately one nanosecond. The fourth region is dominated by vibrational deexcitation and solid species formation as chemical and thermal equilibrium is approached. This is the region measured by current nanosecond resolution techniques and can last from nanoseconds to microseconds depending on the oxygen balance of the solid explosive.

  16. Determination of Nanogram Microparticles from Explosives after Real Open-Air Explosions by Confocal Raman Microscopy.

    PubMed

    Zapata, Félix; García-Ruiz, Carmen

    2016-07-01

    Explosives are increasingly being used for terrorist attacks to cause devastating explosions. The detection of their postblast residues after an explosion is a high challenge, which has been barely investigated, particularly using spectroscopic techniques. In this research, a novel methodology using confocal Raman microscopy has been developed for the analysis of postblast residues from 10 open-air explosions caused by 10 different explosives (TNT, RDX, PETN, TATP, HMTD, dynamite, black powder, ANFO, chloratite, and ammonal) commonly used in improvised explosive devices. The methodology for the determination of postblast particles from explosives consisted of examining the samples surfaces with both the naked eye, first, and microscopically (10× and 50×), immediately afterward; and finally, analyzing the selected residues by confocal Raman spectroscopy in order to identify the postblast particles from explosives. Interestingly, confocal Raman microscopy has demonstrated to be highly suitable to rapidly, selectively, and noninvasively analyze postblast microscopic particles from explosives up to the nanogram range. PMID:27281604

  17. Etude théorique des paramètres principaux réglant la sensibilité des capteurs d'accélération à cristal de quartz

    NASA Astrophysics Data System (ADS)

    Delaite, R.; Aïch, Y.

    1994-10-01

    A theoretical analysis of quartz accelerometers is performed to determine their optimal mechanical and sensitivity performances. A general analytical model is used to investigate the parameters and their effects on the sensitivity of these sensors. The analysis of physical characteristics shows that feasibility and performances depend on three factors such as dimensions of the quartz plate, quantity of holders located at the crystal edge and location of these holders with respect to the crystal's crystallographic reference. This study is applied to various design sensors with different supporting quartz crystal. The conditions on parameters are given to achieve optimum performances. Une étude théorique de la sensibilité des capteurs d'accélération à cristal de quartz est présentée. Son but est d'optimiser les performances mécaniques et métrologiques de ces capteurs. Les paramètres sensibles sont mis en évidence. L'analyse des caractéristiques physiques démontre que la faisabilité et les performances des accéléromètres à quartz dépendent, pour une coupe donnée du cristal, de trois facteurs : les dimensions de la lame de quartz, le nombre de liaisons à la périphérie du cristal et la position de ces liaisons par rapport à la référence cristallographique. L'étude est appliquée aux cas des capteurs bipodes, multipodes et monopodes. Pour chaque type de capteur, les valeurs des paramètres sensibles correspondant aux performances optimales sont précisées.

  18. Data base of chemical explosions in Kazakhstan

    SciTech Connect

    Demin, V.N.; Malahova, M.N.; Martysevich, P.N.; Mihaylova, N.N.; Nurmagambetov, A.; Kopnichev, Yu.F. D.; Edomin, V.I.

    1996-12-01

    Within the bounds of this report, the following works were done: (1) Information about explosion quarries, located in Southern, Eastern and Northern Kasakstan was summarized. (2) The general information about seismicity of areas of location of explosion quarries was adduced. (3) The system of observation and seismic apparatus, recording the local earthquakes and quarry explosions at the territory of Kazakstan were described. (4) Data base of quarry explosions, that were carried out in Southern, Eastern and Northern Kazakstan during 1995 and first half of 1996 year was adduced. (5) Upon the data of registration of explosions in Southern Kazakstan the correlative dependences between power class of explosions and summary weight of charge were constructed. (6) Seismic records of quarry explosions were adduced. It is necessary to note, that the collection of data about quarry explosions in Kazakstan in present time is very difficult task. Organizations, that makes these explosions, are always suffering reorganizations and sometimes it is actually impossible to receive all the necessary information. Some quarries are situated in remote, almost inaccessible regions, and within the bounds of supplier financing not the every quarry was in success to visit. So the present data base upon the chemical explosions for 1995 is not full and in further it`s expansion is possible.

  19. Intravesical explosions during transurethral endoscopic procedures.

    PubMed

    Khan, A; Masood, J; Ghei, M; Kasmani, Z; Ball, A J; Miller, R

    2007-01-01

    Every Urologist, during the course of fulguration treatment of bladder tumours, has at some time or another experienced small intravesical explosions usually manifesting as a "pop". Major intravesical explosions are rare but potentially devastating complications of transurethral endoscopic resections. The damage to the bladder can range from small mucosal tears to bladder rupture, which can either be intraperitoneal (requiring laparotomy and open bladder repair) or extraperitoneal. We review the literature on intravesical explosions to determine the aetiology of these explosions and suggest strategies to prevent these. A comprehensive literature search was performed using Medline and Ovid to obtain information using search terms: intravesical explosions, transurethral procedures, endoscopic procedures, diathermyIntravesical explosions occur due to the production of explosive gases during use of diathermy on human tissues. The most dangerous combination is hydrogen and oxygen. Hydrogen alone is not explosive and it only becomes explosive when admixed with oxygen. Oxygen is not produced in sufficient quantity during diathermy to cause explosions but can enter into the bladder from the atmosphere during endoscopic procedures. Careful operative technique (correct use of the Ellick evacuator bulb and reducing the frequency of manual irrigations of the bladder) with minimisation of the operative time and using the coagulation current at moderate power as well as judicious coagulation of tissues can reduce the risk of this dangerous complication arising. PMID:17171415

  20. Hydrodynamics of explosion: models and software for modeling explosions and estimation of their consequences

    NASA Astrophysics Data System (ADS)

    Stepanov, K. L.; Stankevich, Y. A.; Smetannikov, A. S.

    2012-11-01

    Physical and hydrodynamic processes accompanying explosions of condensed explosives and fuel-air mixtures have been considered. Wide-range equations of state of explosion products and air have been used. A physical model and a program code based on the gas dynamics equations in the Lagrangian form have been developed for modeling one-dimensional hydrodynamic processes in the near zone of explosion. This firmware forms the basis for estimation of explosion consequences. The described model has shown its working efficiency within a wide range of explosion energies and environmental conditions.

  1. Explosive response model evaluation using the explosive H6

    NASA Astrophysics Data System (ADS)

    Sutherland, Gerrit T.; Burns, Joseph

    2000-04-01

    Reactive rate model parameters for a two term Lee Tarver [simplified ignition and growth (SIG)] model were obtained for the explosive H6 from modified gap test data. These model was used to perform simulations of the underwater sensitivity test (UST) using the CTH hydrocode. Reaction was predicted in the simulations for the same water gaps that reaction was observed in the UST. The expansions observed for the UST samples were not simulated correctly, and this is attributed to the density equilibrium conditions imposed between unreacted and reacted components in CTH for the Lee-Tarver model.

  2. Thermal explosion in oscillating ambient conditions

    NASA Astrophysics Data System (ADS)

    Novozhilov, Vasily

    2016-07-01

    Thermal explosion problem for a medium with oscillating ambient temperature at its boundaries is considered. This is a new problem in thermal explosion theory, not previously considered in a distributed system formulation, but important for combustion and fire science. It describes autoignition of wide range of fires (such as but not limited to piles of biosolids and other organic matter; storages of munitions, explosives, propellants) subjected to temperature variations, such as seasonal or day/night variation. The problem is considered in formulation adopted in classical studies of thermal explosion. Critical conditions are determined by frequency and amplitude of ambient temperature oscillations, as well as by a number of other parameters. Effects of all the parameters on critical conditions are quantified. Results are presented for the case of planar symmetry. Development of thermal explosion in time is also considered, and a new type of unsteady thermal explosion development is discovered where thermal runaway occurs after several periods of temperature oscillations within the medium.

  3. Explosive Surface Hardening of Austenitic Stainless Steel

    NASA Astrophysics Data System (ADS)

    Kovacs-Coskun, T.

    2016-04-01

    In this study, the effects of explosion hardening on the microstructure and the hardness of austenitic stainless steel have been studied. The optimum explosion hardening technology of austenitic stainless steel was researched. In case of the explosive hardening used new idea mean indirect hardening setup. Austenitic stainless steels have high plasticity and can be easily cold formed. However, during cold processing the hardening phenomena always occurs. Upon the explosion impact, the deformation mechanism indicates a plastic deformation and this deformation induces a phase transformation (martensite). The explosion hardening enhances the mechanical properties of the material, includes the wear resistance and hardness. In case of indirect hardening as function of the setup parameters specifically the flayer plate position the hardening increased differently. It was find a relationship between the explosion hardening setup and the hardening level.

  4. Explosives Detection: Exploitation of the Physical Signatures

    NASA Astrophysics Data System (ADS)

    Atkinson, David

    2010-10-01

    Explosives based terrorism is an ongoing threat that is evolving with respect to implementation, configuration and materials used. There are a variety of devices designed to detect explosive devices, however, each technology has limitations and operational constraints. A full understanding of the signatures available for detection coupled with the array of detection choices can be used to develop a conceptual model of an explosives screening operation. Physics based sensors provide a robust approach to explosives detection, typically through the identification of anomalies, and are currently used for screening in airports around the world. The next generation of detectors for explosives detection will need to be more sensitive and selective, as well as integrate seamlessly with devices focused on chemical signatures. An appreciation for the details of the physical signature exploitation in cluttered environments with time, space, and privacy constraints is necessary for effective explosives screening of people, luggage, cargo, and vehicles.

  5. Eigenvalue Detonation of Combined Effects Aluminized Explosives

    NASA Astrophysics Data System (ADS)

    Capellos, Christos; Baker, Ernest; Balas, Wendy; Nicolich, Steven; Stiel, Leonard

    2007-06-01

    This paper reports on the development of theory and performance for recently developed combined effects aluminized explosives. Traditional high energy explosives used for metal pushing incorporate high loading percentages of HMX or RDX, whereas blast explosives incorporate some percentage of aluminum. However, the high blast explosives produce increased blast energies, with reduced metal pushing capability due to late time aluminum reaction. Metal pushing capability refers to the early volume expansion work produced during the first few volume expansions associated with cylinder wall velocities and Gurney energies. Our Recently developed combined effects aluminized explosives (PAX-29C, PAX-30, PAX-42) are capable of achieving excellent metal pushing and high blast energies. Traditional Chapman-Jouguet detonation theory does not explain the observed detonation states achieved by these combined effects explosives. This work demonstrates, with the use of cylinder expansion data and thermochemical code calculations (JAGUAR and CHEETAH), that eigenvalue detonation theory explains the observed behavior.

  6. Stellar Explosions: Hydrodynamics and Nucleosynthesis

    NASA Astrophysics Data System (ADS)

    José, Jordi

    2015-12-01

    Stars are the main factories of element production in the universe through a suite of complex and intertwined physical processes. Such stellar alchemy is driven by multiple nuclear interactions that through eons have transformed the pristine, metal-poor ashes leftover by the Big Bang into a cosmos with 100 distinct chemical species. The products of stellar nucleosynthesis frequently get mixed inside stars by convective transport or through hydrodynamic instabilities, and a fraction of them is eventually ejected into the interstellar medium, thus polluting the cosmos with gas and dust. The study of the physics of the stars and their role as nucleosynthesis factories owes much to cross-fertilization of different, somehow disconnected fields, ranging from observational astronomy, computational astrophysics, and cosmochemistry to experimental and theoretical nuclear physics. Few books have simultaneously addressed the multidisciplinary nature of this field in an engaging way suitable for students and young scientists. Providing the required multidisciplinary background in a coherent way has been the driving force for Stellar Explosions: Hydrodynamics and Nucleosynthesis. Written by a specialist in stellar astrophysics, this book presents a rigorous but accessible treatment of the physics of stellar explosions from a multidisciplinary perspective at the crossroads of computational astrophysics, observational astronomy, cosmochemistry, and nuclear physics. Basic concepts from all these different fields are applied to the study of classical and recurrent novae, type I and II supernovae, X-ray bursts and superbursts, and stellar mergers. The book shows how a multidisciplinary approach has been instrumental in our understanding of nucleosynthesis in stars, particularly during explosive events.

  7. Explosion Welding for Hermetic Containerization

    NASA Technical Reports Server (NTRS)

    Dolgin, Benjamin; Sanok, Joseph

    2003-01-01

    A container designed for storing samples of hazardous material features a double wall, part of which is sacrificed during an explosion-welding process in which the container is sealed and transferred to a clean environment. The major advantage of this container sealing process is that once the samples have been sealed inside, the outer wall of what remains of the container is a clean surface that has not come into contact with the environment from which the samples were taken. Thus, there is no need to devise a decontamination process capable of mitigating all hazards that might be posed by unanticipated radioactive, chemical, and/or biological contamination of the outside of the container. The container sealing method was originally intended to be used to return samples from Mars to Earth, but it could also be used to store samples of hazardous materials, without the need to decontaminate its outer surface. The process stages are shown. In its initial double-wall form, the volume between the walls is isolated from the environment; in other words, the outer wall (which is later sacrificed) initially serves to protect the inner container from contamination. The sample is placed inside the container through an opening at one end, then the container is placed into a transfer dock/lid. The surfaces that will be welded together under the explosive have been coated with a soft metallic sacrificial layer. During the explosion, the sacrificial layer is ejected, and the container walls are welded together, creating a strong metallic seal. The inner container is released during the same event and enters the clean environment.

  8. Shock Initiation of Damaged Explosives

    SciTech Connect

    Chidester, S K; Vandersall, K S; Tarver, C M

    2009-10-22

    Explosive and propellant charges are subjected to various mechanical and thermal insults that can increase their sensitivity over the course of their lifetimes. To quantify this effect, shock initiation experiments were performed on mechanically and thermally damaged LX-04 (85% HMX, 15% Viton by weight) and PBX 9502 (95% TATB, 5% Kel-F by weight) to obtain in-situ manganin pressure gauge data and run distances to detonation at various shock pressures. We report the behavior of the HMX-based explosive LX-04 that was damaged mechanically by applying a compressive load of 600 psi for 20,000 cycles, thus creating many small narrow cracks, or by cutting wedge shaped parts that were then loosely reassembled, thus creating a few large cracks. The thermally damaged LX-04 charges were heated to 190 C for long enough for the beta to delta solid - solid phase transition to occur, and then cooled to ambient temperature. Mechanically damaged LX-04 exhibited only slightly increased shock sensitivity, while thermally damaged LX-04 was much more shock sensitive. Similarly, the insensitive explosive PBX 9502 was mechanically damaged using the same two techniques. Since PBX 9502 does not undergo a solid - solid phase transition but does undergo irreversible or 'rachet' growth when thermally cycled, thermal damage to PBX 9502 was induced by this procedure. As for LX-04, the thermally damaged PBX 9502 demonstrated a greater shock sensitivity than mechanically damaged PBX 9502. The Ignition and Growth reactive flow model calculated the increased sensitivities by igniting more damaged LX-04 and PBX 9502 near the shock front based on the measured densities (porosities) of the damaged charges.

  9. Air Activation Following an Atmospheric Explosion

    SciTech Connect

    Lowrey, Justin D.; McIntyre, Justin I.; Prichard, Andrew W.; Gesh, Christopher J.

    2013-03-13

    In addition to thermal radiation and fission products, nuclear explosions result in a very high flux of unfissioned neutrons. Within an atmospheric nuclear explosion, these neutrons can activate the various elemental components of natural air, potentially adding to the radioactive signature of the event as a whole. The goal of this work is to make an order-of-magnitude estimate of the total amount of air activation products that can result from an atmospheric nuclear explosion.

  10. Wireless sensor for detecting explosive material

    SciTech Connect

    Lamberti, Vincent E; Howell, Jr., Layton N; Mee, David K; Sepaniak, Michael J

    2014-10-28

    Disclosed is a sensor for detecting explosive devices. The sensor includes a ferromagnetic metal and a molecular recognition reagent coupled to the ferromagnetic metal. The molecular recognition reagent is operable to expand upon absorption of vapor from an explosive material such that the molecular recognition reagent changes a tensile stress upon the ferromagnetic metal. The explosive device is detected based on changes in the magnetic switching characteristics of the ferromagnetic metal caused by the tensile stress.

  11. On the geophysical fingerprint of Vulcanian explosions

    NASA Astrophysics Data System (ADS)

    Gottsmann, J.; De Angelis, S.; Fournier, N.; Van Camp, M.; Sacks, S.; Linde, A.; Ripepe, M.

    2011-06-01

    Extrusion of viscous magma and the subsequent formation of a lava dome is often interspersed by short-lived vigorous (Vulcanian) explosions. The causes for and the timing of the transition from effusive to explosive activity during dome formation are poorly understood and forecasting this transition remains a challenge. Here, we describe and interpret a robust and unique multi-parameter data set documenting the subsurface processes associated with Vulcanian explosions at Soufrière Hills Volcano, Montserrat (W.I.) in July and December 2008. We quantify explosion priming by processes in either the shallow (< 2 km depth) or the deep magmatic system and quantify syn-eruptive processes. The July 29 explosion has a signature related exclusively to shallow dynamics including conduit destabilisation, syn-eruptive decompression and magma fragmentation, conduit emptying and expulsion of juvenile pumice. In contrast, the December 3 explosion was triggered by unprecedented sudden pressurisation of the entire plumbing system from depths of about 10 km (including the magma chambers) resulting in surficial dome carapace failure, a violent cannon-like explosion, propagation of pressure waves and pronounced ballistic ejection of dome fragments. With timescales for explosion priming on the order of a few minutes, the precursory geophysical signatures are indicative of the nature of ensuing Vulcanian explosions. The short precursory phases characterise Vulcanian explosions as freak events triggered by abrupt rather than gradual changes in subsurface dynamics. Our findings provide important constraints for theoretical and experimental investigations of the effusive to explosive transition, forecasting of Vulcanian explosions and volcanic risk mitigation.

  12. Supernova Explosions Stay In Shape

    NASA Astrophysics Data System (ADS)

    2009-12-01

    At a very early age, children learn how to classify objects according to their shape. Now, new research suggests studying the shape of the aftermath of supernovas may allow astronomers to do the same. A new study of images from NASA's Chandra X-ray Observatory on supernova remnants - the debris from exploded stars - shows that the symmetry of the remnants, or lack thereof, reveals how the star exploded. This is an important discovery because it shows that the remnants retain information about how the star exploded even though hundreds or thousands of years have passed. "It's almost like the supernova remnants have a 'memory' of the original explosion," said Laura Lopez of the University of California at Santa Cruz, who led the study. "This is the first time anyone has systematically compared the shape of these remnants in X-rays in this way." Astronomers sort supernovas into several categories, or "types", based on properties observed days after the explosion and which reflect very different physical mechanisms that cause stars to explode. But, since observed remnants of supernovas are leftover from explosions that occurred long ago, other methods are needed to accurately classify the original supernovas. Lopez and colleagues focused on the relatively young supernova remnants that exhibited strong X-ray emission from silicon ejected by the explosion so as to rule out the effects of interstellar matter surrounding the explosion. Their analysis showed that the X-ray images of the ejecta can be used to identify the way the star exploded. The team studied 17 supernova remnants both in the Milky Way galaxy and a neighboring galaxy, the Large Magellanic Cloud. For each of these remnants there is independent information about the type of supernova involved, based not on the shape of the remnant but, for example, on the elements observed in it. The researchers found that one type of supernova explosion - the so-called Type Ia - left behind relatively symmetric, circular

  13. Evaluation of surface storage facilities for explosives, blasting agents and other explosive materials

    NASA Astrophysics Data System (ADS)

    Roth, J.

    1983-06-01

    The histories of recent and past magazine explosions were reviewed; present explosive storage conditions and practices were observed; and existing Federal regulations on explosive storage were examined. A recent increase in magazine explosion frequency must be attributed to a large increase in deliberate explosions; fires of various origins account for the remaining explosions of the past decade. During 1884-1926 several lightning generated explosions occurred in nonmetal magazines. It appears that the contents of a well constructed metal magazine are immune to direct lightning strikes, regardless of whether the magazine is grounded or not. Grounding a metal magazine cannot be harmful, but it maywell be superfluous. Mine Safety and Health Administration and Bureau of Alcohol, Tobacco and Firearms standards on explosive storage appear to cover safety aspects adequately. Certain revisions are recommended to clarify some of the standards and to reduce inconsistencies in their enforcement.

  14. The Safety Aspects of Handling Primary Explosives

    NASA Astrophysics Data System (ADS)

    Mehta, Neha; Oyler, Karl; Cheng, Gartung

    2013-06-01

    Primary Explosives, unlike secondary explosives, show a very rapid transition from deflagration to detonation and are considerably sensitive to small stimuli, such as impact,friction, electrostatic discharge, and heat. Primary explosives generate either a large amount of heat or a shockwave which makes the transfer of the detonation to a less sensitive propellant or secondary explosive possible. Primary explosives are key components in detonators and primers, which are the initiating elements to many military items such as small, medium and large caliber munitions, mortars, artilleries, warheads, etc. The two most common military primary explosives are lead azide and lead styphnate. Lead based compounds such as these are well-established hazards to health and the environment. To overcome these concerns, we are seeking to replace lead azide in common U.S. Army detonators and primers with DBX-1. Further, in order to minimize the dangers to personnel and equipment associated with synthesizing and handling primary explosives, we have developed a dedicated, remote-operated facility for the synthesis and testing of primary explosives. This paper will present the characterization capabilities and testing methods of primary explosives safe, along with the automation process developed.

  15. Momentum transfer in indirect explosive drive

    SciTech Connect

    Kennedy, J.E.; Warnes, R.H.; Cherry, C.R.; Cherry, C.R. Jr.; Fischer, S.H.

    1996-07-01

    Material which is not in direct contact with detonating explosives may still be driven by the explosion through impact by driven material or by attachment to driven material. In such circumstances the assumption of inelastic collision permits estimation of the final velocity of an assemblage. Examples of the utility of this assumption are demonstrated through use of Gurney equations. The inelastic collision calculation may also be used for metal parts which are driven by explosives partially covering the metal. We offer a new discounting angle to account for side energy losses from laterally unconfined explosive charges in cases where the detonation wave travels parallel to the surface which is driven.

  16. Method and apparatus for detecting explosives

    DOEpatents

    Moore, David Steven

    2011-05-10

    A method and apparatus is provided for detecting explosives by thermal imaging. The explosive material is subjected to a high energy wave which can be either a sound wave or an electromagnetic wave which will initiate a chemical reaction in the explosive material which chemical reaction will produce heat. The heat is then sensed by a thermal imaging device which will provide a signal to a computing device which will alert a user of the apparatus to the possibility of an explosive device being present.

  17. Probing the Cassiopeia A Supernova Explosion

    SciTech Connect

    Hwang, Una; Laming, J. Martin

    2007-08-02

    X-ray observations of the Cassiopeia A supernova remnant reveal explosive nucleosynthesis products such as Si and Fe, and thus provide a unique window into the core-collapse explosion that formed the remnant 330 years ago. We review current progress using X-ray spectra extracted on arcsecond angular scales from a 106 s Chandra observation of Cas A, in conjunction with models that follow the remnant's hydrodynamical evolution and treat the relevant plasma microphysics. We address questions related to the explosion such as the degree of explosion asymmetry, the nature of the jets, the nature of the circumstellar environment, and extent of radial mixing of the Fe ejecta.

  18. Overall characterization of cork dust explosion.

    PubMed

    Pilão, R; Ramalho, E; Pinho, C

    2006-05-20

    Explosibility and ignitability studies of air/cork dust mixtures were conducted in a near-spherical 22.7 L explosibility test chamber using pyrotechnic ignitors and in a furnace of 1.23 L. The suspension dust burned as air-dispersed dust clouds and the uniformity of the dispersion inside the chamber was evaluated through optical dust probes. The range of tested particle sizes went from a mass median diameter of 47.4 to 438.3 microm and the covered dust cloud concentration was up to 700-800 g/m(3). Measured explosion parameters included minimum explosible concentration, maximum explosion pressure, maximum rate of pressure rise and minimum autoignition temperature. The effect of dust particle size on flammability was evaluated and it was found that the minimum explosible concentration is around 40 g/m(3) and it is relatively independent of particle size below 180 microm. Maximum explosion pressure of 7.2 bar and maximum rate of pressure rise of 179 bar/s were detected for the smallest tested sizes. The limitations on the rates of devolatilization of the solid particles became rate controlling at high burning velocities, at high dust loadings and for large particle sizes. The effect of initial pressure on the characteristic parameters of the explosion was studied by varying the initial absolute pressure from 0.9 bar to 2.2 bar, and it was found that as initial pressure increases, there is a proportional increase of minimum explosion limit, maximum explosion pressure, and maximum rate of pressure rise. The influence of the intensity of the ignition energy on the development of the explosion was evaluated using ignition energies of 1000 J, 2500 J and 5000 J, and the experimental data showed that the value of 2500 J is the most convenient to use in the determination of minimum explosion concentration. The behavior of the cork dust explosion in hybrid methane air mixtures was studied for atmospheres with 2% and 3.5% (v/v) of methane. The effect of methane content on the

  19. Developpement D'un Modele Climatique Regional: Fizr Simulation des Conditions de Janvier de la Cote Ouest Nord Americaine

    NASA Astrophysics Data System (ADS)

    Goyette, Stephane

    1995-11-01

    . Cette nouvelle gamme de modeles-interpolateurs imbriques qualifies d'"intelligents" fait partie de la famille des modeles dits "pilotes". L'hypothese directrice de notre etude est fondee sur la supposition que le climat de fine echelle est souvent gouverne par des forcages provenant de la surface plutot que par des transports atmospheriques de grande echelle spatiale. La technique que nous proposons vise donc a guider FIZR par la Dynamique echantillonnee d'un MCG et de la forcer par la Physique du MCG ainsi que par un forcage orographique de meso-echelle, en chacun des noeuds de la grille fine de calculs. Afin de valider la robustesse et la justesse de notre modele climatique regional, nous avons choisi la region de la Cote Ouest du continent nord americain. Elle est notamment caracterisee par une distribution geographique des precipitations et des temperatures fortement influencee par le relief sous-jacent. Les resultats d'une simulation d'un mois de janvier avec FIZR demontrent que nous pouvons simuler des champs de precipitations et de temperatures au niveau de l'abri beaucoup plus pres des observations climatiques comparativement a ceux simules a partir d'un MCG. Ces performances sont manifestement attribuees au forcage orographique de meso-echelle de meme qu'aux caracteristiques de surface determinees a fine echelle. Un modele similaire a FIZR peut, en principe, etre implante sur l'importe quel MCG, donc, tout organisme de recherche implique en modelisation numerique mondiale de grande echelle pourra se doter d'un el outil de regionalisation.

  20. 27 CFR 555.63 - Explosives magazine changes.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2012-04-01 2010-04-01 true Explosives magazine changes..., AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Licenses and Permits § 555.63 Explosives magazine changes. (a) General. (1) The requirements of this section are applicable to...

  1. 27 CFR 555.23 - List of explosive materials.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2012-04-01 2010-04-01 true List of explosive materials..., AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Administrative and Miscellaneous Provisions § 555.23 List of explosive materials. The Director shall compile a list of...

  2. 27 CFR 555.28 - Stolen explosive materials.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2012-04-01 2010-04-01 true Stolen explosive materials..., AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Administrative and Miscellaneous Provisions § 555.28 Stolen explosive materials. No person shall receive, conceal, transport,...

  3. 30 CFR 75.1310 - Explosives and blasting equipment.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Explosives and blasting equipment. 75.1310... SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Explosives and Blasting § 75.1310 Explosives and blasting equipment. (a) Only permissible explosives, approved sheathed explosive units,...

  4. 30 CFR 75.1310 - Explosives and blasting equipment.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Explosives and blasting equipment. 75.1310... SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Explosives and Blasting § 75.1310 Explosives and blasting equipment. (a) Only permissible explosives, approved sheathed explosive units,...

  5. 27 CFR 555.63 - Explosives magazine changes.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2013-04-01 2013-04-01 false Explosives magazine..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Licenses and Permits § 555.63 Explosives magazine changes. (a) General. (1) The requirements of this section are...

  6. 27 CFR 555.63 - Explosives magazine changes.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2010-04-01 2010-04-01 false Explosives magazine..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Licenses and Permits § 555.63 Explosives magazine changes. (a) General. (1) The requirements of this section are...

  7. 30 CFR 75.1310 - Explosives and blasting equipment.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Explosives and blasting equipment. 75.1310... SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Explosives and Blasting § 75.1310 Explosives and blasting equipment. (a) Only permissible explosives, approved sheathed explosive units,...

  8. 27 CFR 555.28 - Stolen explosive materials.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2011-04-01 2010-04-01 true Stolen explosive materials..., AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Administrative and Miscellaneous Provisions § 555.28 Stolen explosive materials. No person shall receive, conceal, transport,...

  9. 27 CFR 555.23 - List of explosive materials.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2011-04-01 2010-04-01 true List of explosive materials..., AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Administrative and Miscellaneous Provisions § 555.23 List of explosive materials. The Director shall compile a list of...

  10. 30 CFR 75.1310 - Explosives and blasting equipment.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Explosives and blasting equipment. 75.1310... SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Explosives and Blasting § 75.1310 Explosives and blasting equipment. (a) Only permissible explosives, approved sheathed explosive units,...

  11. 27 CFR 555.23 - List of explosive materials.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2013-04-01 2013-04-01 false List of explosive..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Administrative and Miscellaneous Provisions § 555.23 List of explosive materials. The Director shall compile a list of...

  12. 27 CFR 555.63 - Explosives magazine changes.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2011-04-01 2010-04-01 true Explosives magazine changes..., AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Licenses and Permits § 555.63 Explosives magazine changes. (a) General. (1) The requirements of this section are applicable to...

  13. 27 CFR 555.28 - Stolen explosive materials.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2013-04-01 2013-04-01 false Stolen explosive materials..., AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Administrative and Miscellaneous Provisions § 555.28 Stolen explosive materials. No person shall receive, conceal, transport,...

  14. 27 CFR 555.23 - List of explosive materials.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2010-04-01 2010-04-01 false List of explosive..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Administrative and Miscellaneous Provisions § 555.23 List of explosive materials. The Director shall compile a list of...

  15. 27 CFR 555.28 - Stolen explosive materials.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2010-04-01 2010-04-01 false Stolen explosive materials..., AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Administrative and Miscellaneous Provisions § 555.28 Stolen explosive materials. No person shall receive, conceal, transport,...

  16. 27 CFR 555.63 - Explosives magazine changes.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2014-04-01 2014-04-01 false Explosives magazine..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Licenses and Permits § 555.63 Explosives magazine changes. (a) General. (1) The requirements of this section are...

  17. 30 CFR 75.1310 - Explosives and blasting equipment.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Explosives and blasting equipment. 75.1310... SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Explosives and Blasting § 75.1310 Explosives and blasting equipment. (a) Only permissible explosives, approved sheathed explosive units,...

  18. 27 CFR 555.23 - List of explosive materials.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2014-04-01 2014-04-01 false List of explosive..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Administrative and Miscellaneous Provisions § 555.23 List of explosive materials. The Director shall compile a list of...

  19. 27 CFR 555.28 - Stolen explosive materials.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2014-04-01 2014-04-01 false Stolen explosive materials..., AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Administrative and Miscellaneous Provisions § 555.28 Stolen explosive materials. No person shall receive, conceal, transport,...

  20. 27 CFR 70.445 - Commerce in explosives.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... Cartridges, and Explosives § 70.445 Commerce in explosives. Part 55 of title 27 CFR contains the regulations... 27 Alcohol, Tobacco Products and Firearms 2 2010-04-01 2010-04-01 false Commerce in explosives. 70..., explosives, (b) Permits for users who buy or transport explosives in interstate or foreign commerce,...

  1. 27 CFR 555.181 - Reporting of plastic explosives.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2012-04-01 2010-04-01 true Reporting of plastic..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Marking of Plastic Explosives § 555.181 Reporting of plastic explosives. All persons, other than an agency of the United...

  2. 27 CFR 555.181 - Reporting of plastic explosives.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2014-04-01 2014-04-01 false Reporting of plastic..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Marking of Plastic Explosives § 555.181 Reporting of plastic explosives. All persons, other than an agency of the United...

  3. 27 CFR 555.181 - Reporting of plastic explosives.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2010-04-01 2010-04-01 false Reporting of plastic..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Marking of Plastic Explosives § 555.181 Reporting of plastic explosives. All persons, other than an agency of the United...

  4. 27 CFR 555.181 - Reporting of plastic explosives.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2013-04-01 2013-04-01 false Reporting of plastic..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Marking of Plastic Explosives § 555.181 Reporting of plastic explosives. All persons, other than an agency of the United...

  5. 27 CFR 555.181 - Reporting of plastic explosives.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2011-04-01 2010-04-01 true Reporting of plastic..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Marking of Plastic Explosives § 555.181 Reporting of plastic explosives. All persons, other than an agency of the United...

  6. 27 CFR 70.445 - Commerce in explosives.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... Cartridges, and Explosives § 70.445 Commerce in explosives. Part 555 of title 27 CFR contains the regulations... 27 Alcohol, Tobacco Products and Firearms 2 2011-04-01 2011-04-01 false Commerce in explosives. 70..., explosives, (b) Permits for users who buy or transport explosives in interstate or foreign commerce,...

  7. 29 CFR 1926.903 - Underground transportation of explosives.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 29 Labor 8 2011-07-01 2011-07-01 false Underground transportation of explosives. 1926.903 Section... Explosives § 1926.903 Underground transportation of explosives. (a) All explosives or blasting agents in...) Trucks used for the transportation of explosives underground shall have the electrical system...

  8. 29 CFR 1926.903 - Underground transportation of explosives.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 29 Labor 8 2013-07-01 2013-07-01 false Underground transportation of explosives. 1926.903 Section... Explosives § 1926.903 Underground transportation of explosives. (a) All explosives or blasting agents in...) Trucks used for the transportation of explosives underground shall have the electrical system...

  9. 29 CFR 1926.903 - Underground transportation of explosives.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 29 Labor 8 2014-07-01 2014-07-01 false Underground transportation of explosives. 1926.903 Section... Explosives § 1926.903 Underground transportation of explosives. (a) All explosives or blasting agents in...) Trucks used for the transportation of explosives underground shall have the electrical system...

  10. 29 CFR 1926.903 - Underground transportation of explosives.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 29 Labor 8 2012-07-01 2012-07-01 false Underground transportation of explosives. 1926.903 Section... Explosives § 1926.903 Underground transportation of explosives. (a) All explosives or blasting agents in...) Trucks used for the transportation of explosives underground shall have the electrical system...

  11. 29 CFR 1926.903 - Underground transportation of explosives.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 29 Labor 8 2010-07-01 2010-07-01 false Underground transportation of explosives. 1926.903 Section... Explosives § 1926.903 Underground transportation of explosives. (a) All explosives or blasting agents in...) Trucks used for the transportation of explosives underground shall have the electrical system...

  12. Analyse chronometrique intersexes de la resolution de la tache d'horizontalite des liquides

    NASA Astrophysics Data System (ADS)

    Berthiaume, Francois

    D'abondantes recherches ont demontre que la reussite a la tache d'horizontalite des liquides est en moyenne plus elevee chez les individus de sexe masculin que chez ceux de sexe feminin. Deux facteurs principaux ont ete proposes: il s'agit de la connaissance du principe physique de l'invariance de l'orientation des liquides et de certaines habiletes perceptives d'ordre visuel. Le but de la presente recherche est d'etablir la duree detaillee de la resolution de la tache d'horizontalite des liquides chez 185 filles et 180 garcons, ages de 15 a 19 ans et repartis en 8 groupes. Dans une version informatisee, le premier groupe trace la position de la surface de l'eau a l'interieur d'un contenant dans diverses inclinaisons et le deuxieme evalue si l'orientation d'une ligne y represente bien cette position; le troisieme groupe trace une horizontale dans un rectangle et le quatrieme juge si la ligne illustree y est bien horizontale. Quatre autres groupes executent respectivement les memes taches dans la version classique papier-crayon. Le temps accorde a la reflexion avant de commencer le trace, le temps de tracage comme tel et le temps de verification du trace complete sont calcules. Chez les groupes qui evaluent l'orientation d'une ligne sur support informatique, le temps requis pour y parvenir est note. Enfin, un questionnaire estime si les participants connaissent ou non le principe physique d'invariance de l'orientation de la surface d'un liquide. Les resultats revelent que cette connaissance est plus frequente chez les garcons dans l'ensemble des groupes. Dans le cas ou les sujets ont a tracer une ligne, les filles reussissent moins d'essais que les garcons s'il faut, sur support informatique, tracer la surface de l'eau dans un contenant incline ou a l'horizontale. Il en va de meme s'il faut, sur support papier, tracer une horizontale dans un contenant incline. Le trace de la surface de l'eau est plus exact chez les sujets connaissant le principe d'invariance et l

  13. Estimation of explosive charge mass used for explosions on concrete surface for the forensic purpose.

    PubMed

    Bjelovuk, Ivana D; Jaramaz, Slobodan; Mickovic, Dejan

    2012-03-01

    The method of choice used by most terrorists for achieving political goals remains the utilization of explosive devices and there is always visible evidence at a crime scene after the deployment of such devices. Given favorable circumstances, forensic analysis can determine the cause of the explosion - the type of the explosive device, the means of detonation, the type and mass of the explosive charge that has been used and perhaps provide information to lead to the identity of the individual who may have constructed or deployed the explosive device, etc. Evidence of an explosion may take the form of a crater or other damage which may provide some information facilitating and estimating the mass of explosive material used. This paper reports the findings obtained by performing experimental explosions of known charges on a concrete surface, in order to establish the correlation between the charge weight and the effects of the explosion. Known masses of explosives were fired and the dimensions of craters made by explosions were measured. Five empirical equations for estimation of the explosive charge mass from crater dimensions were used. PMID:22325907

  14. 75 FR 1085 - Commerce in Explosives; List of Explosive Materials (2009R-18T)

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-01-08

    ... 31, 2008 (Docket No. ATF 28N, 73 FR 80428). Notice of List of Explosive Materials Pursuant to 18 U.S... powder. Black powder based explosive mixtures. *Blasting agents, nitro-carbo-nitrates, including non-cap sensitive slurry and water gel explosives. Blasting caps. Blasting gelatin. Blasting powder. BTNEC ....

  15. The locations of cosmic explosions

    NASA Technical Reports Server (NTRS)

    Fruchter, A. S.; Levan, A. J.; Strolger, L.; Vreeswijk, P. M.; Bersier, D.; Burud, I.; Castro-Ceron, J. M.; Consclice, C.; Dahlen, T.; Strolger, L.

    2005-01-01

    When massive stars exhaust their fuel they collapse and often produce the extraordinarily bright explosions known as core-collapse supernovae. Recently, it has become apparent that stellar collapse can power the even more brilliant relativistic explosions known as long-duration gamma-ray bursts. In some cases, a gamma-ray burst and a supernova have been observed from the same event. One would thus expect that gamma-ray bursts and supernovae should be found in similar environments. Here we show that this expectation is wrong. Using Hubble Space Telescope imaging of the host galaxies of long-duration gamma-ray bursts and core-collapse supernovae, we demonstrate that while the distribution of the supernovae in their hosts traces the blue light of young stars, the gamma-ray bursts are much more concentrated on the very brightest regions of their hosts. Furthermore, the host galaxies of the gamma-ray bursts are significantly fainter and more irregular than the hosts of the supernovae. Together these results suggest that long-duration gamma-ray bursts are associated with the very most massive stars and may be restricted to galaxies of limited chemical evolution. Our results directly imply that long-duration gamma-ray bursts are relatively rare in galaxies such as our own Milky Way.

  16. Explosive double salts and preparation

    DOEpatents

    Cady, Howard H.; Lee, Kien-yin

    1984-01-01

    Applicants have discovered a new composition of matter which is an explosive addition compound of ammonium nitrate (AN) and diethylenetriamine trinitrate (DETN) in a 50:50 molar ratio. The compound is stable over extended periods of time only at temperatures higher than 46.degree. C., decomposing to a fine-grained eutectic mixture (which is also believed to be new) of AN and DETN at temperatures lower than 46.degree. C. The compound of the invention has an x-ray density of 1.61 g/cm.sup.3, explodes to form essentially only gaseous products, has higher detonation properties (i.e., detonation velocity and pressure) than those of any mechanical mixture having the same density and composition as the compound of the invention, is a quite insensitive explosive material, can be cast at temperatures attainable by high pressure steam, and is prepared from inexpensive ingredients. Methods of preparing the compound of the invention and the fine-grained eutectic composition of the invention are given.

  17. High temperature two component explosive

    DOEpatents

    Mars, James E.; Poole, Donald R.; Schmidt, Eckart W.; Wang, Charles

    1981-01-01

    A two component, high temperature, thermally stable explosive composition comprises a liquid or low melting oxidizer and a liquid or low melting organic fuel. The oxidizer and fuel in admixture are incapable of substantial spontaneous exothermic reaction at temperatures on the order of 475.degree. K. At temperatures on the order of 475.degree. K., the oxidizer and fuel in admixture have an activation energy of at least about 40 kcal/mol. As a result of the high activation energy, the preferred explosive compositions are nondetonable as solids at ambient temperature, and become detonable only when heated beyond the melting point. Preferable oxidizers are selected from alkali or alkaline earth metal nitrates, nitrites, perchlorates, and/or mixtures thereof. Preferred fuels are organic compounds having polar hydrophilic groups. The most preferred fuels are guanidinium nitrate, acetamide and mixtures of the two. Most preferred oxidizers are eutectic mixtures of lithium nitrate, potassium nitrate and sodium nitrate, of sodium nitrite, sodium nitrate and potassium nitrate, and of potassium nitrate, calcium nitrate and sodium nitrate.

  18. Subsurface Explosions in Granular Media

    NASA Astrophysics Data System (ADS)

    Lai, Shuyue; Houim, Ryan; Oran, Elaine

    2015-11-01

    Numerical simulations of coupled gas-granular flows are used to study properties of shock formation and propagation in media, such as sand or regolith on the moon, asteroids, or comets. The simulations were performed with a multidimensional fully compressible model, GRAF, which solves two sets of coupled Navier-Stokes equations, one for the gas and one for the granular medium. The specific case discussed here is for a subsurface explosion in a granular medium initiated by an equivalent of 200g of TNT in depths ranging from 0.1m to 3m. The background conditions of 100K, 10 Pa and loose initial particle volume fraction of 25% are consistent with an event on a comet. The initial blast creates a cavity as a granular shock expands outwards. Since the gas-phase shock propagates faster than the granular shock in loose, granular material, some gas and particles are ejected before the granular shock arrives. When the granular shock reaches the surface, a cap-like structure forms. This cap breaks and may fall back on the surface and in this process, relatively dense particle clusters form. At lower temperatures, the explosion timescales are increased and entrained particles are more densely packed.

  19. [Update: blast and explosion trauma].

    PubMed

    van de Weyer, P S; Praetorius, M; Tisch, M

    2011-08-01

    In recent decades, acoustic shock and explosion traumas have increased in frequency in the general population. Beside the use of fireworks and firearms, airbag ignitions and explosions caused by terror or suicidal acts are also relevant. Depending on duration and strength of the sound pressure affecting the human ear, isolated inner ear damage or additional ear drum perforation and interruption of the middle ear ossicle chain can result. By means of otoscopy, pure tone audiometry, measurement of otoacoustic emissions, and other neurootological examinations, the severity of the trauma can be determined. With prompt and adequate therapy, permanent hearing loss can be minimized. In particular, the measurement of otoacoustic emissions allows conclusions to be made on the functionality of the outer hair cells which are damaged first in most cases. Histological investigations on noise-exposed cochleas show extensive damage to the outer hair cells in the frequency range between 1.0 and 4.0 kHz, which correlates well with audiometric measurements. PMID:21769579

  20. Cosmic Explosions in Three Dimensions

    NASA Astrophysics Data System (ADS)

    Höflich, Peter; Kumar, Pawan; Wheeler, J. Craig

    2011-08-01

    Introduction: 3-D Explosions: a meditation on rotation (and magnetic fields) J. C. Wheeler; Part I. Supernovae: Observations Today: 1. Supernova explosions: lessons from spectropolarimetry L. Wang; 2. Spectropolarimetric observations of Supernovae A. Filippenko and D. C. Leonard; 3. Observed and physical properties of type II plateau supernovae M. Hamuy; 4. SN1997B and the different types of Type Ic Supernovae A. Clocchiatti, B. Leibundgut, J. Spyromilio, S. Benetti, E. Cappelaro, M. Turatto and M. Phillips; 5. Near-infrared spectroscopy of stripped-envelope Supernovae C. L. Gerardy, R. A. Fesen, G. H. Marion, P. Hoeflich and J. C. Wheeler; 6. Morphology of Supernovae remnants R. Fesen; 7. The evolution of Supernova remnants in the winds of massive stars V. Dwarkadas; 8. Types for the galactic Supernovae B. E. Schaefer; Part II. Theory of Thermonuclear Supernovae: 9. Semi-steady burning evolutionary sequences for CAL 83 and CAL 87: supersoft X-ray binaries are Supernovae Ia progenitors S. Starrfield, F. X. Timmes, W. R. Hix, E. M. Sion, W. M. Sparks and S. Dwyer; 10. Type Ia Supernovae progenitors: effects of the spin-up of the white dwarfs S.-C. Yoon and N. Langer; 11. Terrestrial combustion: feedback to the stars E. S. Oran; 12. Non-spherical delayed detonations E. Livne; 13. Numerical simulations of Type Ia Supernovae: deflagrations and detonations V. N. Gamezo, A. M. Khokhlov and E. S. Oran; 14. Type Ia Supernovae: spectroscopic surprises D. Branch; 15. Aspherity effects in Supernovae P. Hoeflich, C. Gerardy and R. Quimby; 16. Broad light curve SneIa: asphericity or something else? A. Howell and P. Nugent; 17. Synthetic spectrum methods for 3-D SN models R. Thomas; 18. A hole in Ia' spectroscopic and polarimetric signatures of SN Ia asymmetry due to a companion star D. Kasen; 19. Hunting for the signatures of 3-D explosions with 1-D synthetic spectra E. Lentz, E. Baron and P. H. Hauschildt; 20. On the variation of the peak luminosity of Type Ia J. W. Truran, E

  1. Cosmic Explosions in Three Dimensions

    NASA Astrophysics Data System (ADS)

    Höflich, Peter; Kumar, Pawan; Wheeler, J. Craig

    2004-12-01

    Introduction: 3-D Explosions: a meditation on rotation (and magnetic fields) J. C. Wheeler; Part I. Supernovae: Observations Today: 1. Supernova explosions: lessons from spectropolarimetry L. Wang; 2. Spectropolarimetric observations of Supernovae A. Filippenko and D. C. Leonard; 3. Observed and physical properties of type II plateau supernovae M. Hamuy; 4. SN1997B and the different types of Type Ic Supernovae A. Clocchiatti, B. Leibundgut, J. Spyromilio, S. Benetti, E. Cappelaro, M. Turatto and M. Phillips; 5. Near-infrared spectroscopy of stripped-envelope Supernovae C. L. Gerardy, R. A. Fesen, G. H. Marion, P. Hoeflich and J. C. Wheeler; 6. Morphology of Supernovae remnants R. Fesen; 7. The evolution of Supernova remnants in the winds of massive stars V. Dwarkadas; 8. Types for the galactic Supernovae B. E. Schaefer; Part II. Theory of Thermonuclear Supernovae: 9. Semi-steady burning evolutionary sequences for CAL 83 and CAL 87: supersoft X-ray binaries are Supernovae Ia progenitors S. Starrfield, F. X. Timmes, W. R. Hix, E. M. Sion, W. M. Sparks and S. Dwyer; 10. Type Ia Supernovae progenitors: effects of the spin-up of the white dwarfs S.-C. Yoon and N. Langer; 11. Terrestrial combustion: feedback to the stars E. S. Oran; 12. Non-spherical delayed detonations E. Livne; 13. Numerical simulations of Type Ia Supernovae: deflagrations and detonations V. N. Gamezo, A. M. Khokhlov and E. S. Oran; 14. Type Ia Supernovae: spectroscopic surprises D. Branch; 15. Aspherity effects in Supernovae P. Hoeflich, C. Gerardy and R. Quimby; 16. Broad light curve SneIa: asphericity or something else? A. Howell and P. Nugent; 17. Synthetic spectrum methods for 3-D SN models R. Thomas; 18. A hole in Ia' spectroscopic and polarimetric signatures of SN Ia asymmetry due to a companion star D. Kasen; 19. Hunting for the signatures of 3-D explosions with 1-D synthetic spectra E. Lentz, E. Baron and P. H. Hauschildt; 20. On the variation of the peak luminosity of Type Ia J. W. Truran, E

  2. Low Frequency Electromagnetic Pulse and Explosions

    SciTech Connect

    Sweeney, J J

    2011-02-01

    This paper reviews and summarizes prior work related to low frequency (< 100 Hz) EMP (ElectroMagnetic Pulse) observed from explosions. It focuses on how EMP signals might, or might not, be useful in monitoring underground nuclear tests, based on the limits of detection, and physical understanding of these signals. In summary: (1) Both chemical and nuclear explosions produce an EMP. (2) The amplitude of the EMP from underground explosions is at least two orders of magnitude lower than from above ground explosions and higher frequency components of the signal are rapidly attenuated due to ground conductivity. (3) In general, in the near field, that is distances (r) of less than 10s of kilometers from the source, the amplitude of the EMP decays approximately as 1/r{sup 3}, which practically limits EMP applications to very close (<{approx}1km) distances. (4) One computational model suggests that the EMP from a decoupled nuclear explosion may be enhanced over the fully coupled case. This has not been validated with laboratory or field data. (5) The magnitude of the EMP from an underground nuclear explosion is about two orders of magnitude larger than that from a chemical explosion, and has a larger component of higher frequencies. In principle these differences might be used to discriminate a nuclear from a chemical explosion using sensors at very close (<{approx}1 km) distances. (6) Arming and firing systems (e.g. detonators, exploding bridge wires) can also produce an EMP from any type of explosion. (7) To develop the understanding needed to apply low frequency EMP to nuclear explosion monitoring, it is recommended to carry out a series of controlled underground chemical explosions with a variety of sizes, emplacements (e.g. fully coupled and decoupled), and arming and firing systems.

  3. Les Sciences Physiques À L'école Maternelle: Un Cadre Sociocognitif Pour La Construction Des Connaissances ET/OU LE Développement Des Activités Didactiques

    NASA Astrophysics Data System (ADS)

    Ravanis, Konstantinos

    2005-05-01

    NATURAL SCIENCES IN KINDERGARTEN: A SOCIO-COGNITIVE FRAMEWORK FOR LEARNING AND TEACHING - The present study presents a socio-cognitive framework for the construction of the scientific knowledge of natural phenomena among pre-school children and for the development of science activities at kindergarten. It involves elements from theories of social interaction; social psychology of development and cognitive functioning; and research in natural-science teaching methods which acknowledge the importance and fundamental role of social interaction in the development of cognitive operations and learning. The study also presents some of the more significant results of the research carried out on different aspects of this topic. The discussion unfolded here supports the hypothesis that the construction of natural-scientific knowledge at the pre-school age and corresponding scholastic activities are necessary and effective.

  4. Teenage Nutrition and Physique.

    ERIC Educational Resources Information Center

    Huenemann, Ruth L.; And Others

    Body size, composition, and conformation in a teen-age population, and associated factors were studied to obtain useful data for planning programs in public health nutrition. This book describes the purpose, methods, and findings of this four-year longitudinal and cross-sectional study conducted in Berkeley, California, during the years 1961 to…

  5. Advancing Explosives Detection Capabilities: Vapor Detection

    ScienceCinema

    Atkinson, David

    2014-07-24

    A new, PNNL-developed method provides direct, real-time detection of trace amounts of explosives such as RDX, PETN and C-4. The method selectively ionizes a sample before passing the sample through a mass spectrometer to detect explosive vapors. The method could be used at airports to improve aviation security.

  6. Detection and dispersal of explosives by ants

    NASA Astrophysics Data System (ADS)

    McFee, John E.; Achal, Steve; Faust, Anthony A.; Puckrin, Eldon; House, Andrew; Reynolds, Damon; McDougall, William; Asquini, Adam

    2009-05-01

    The ability of animals to detect explosives is well documented. Mammalian systems, insects and even single celled organisms have all been studied and in a few cases employed to detect explosives. This paper will describe the potential ability of ants to detect, disperse and possibly neutralize bulk explosives. In spring 2008 a team of DRDC and Itres scientists conducted experiments on detecting surface-laid and buried landmines, improvised explosive devices (IEDs) and their components. Measurements were made using state-of-the-art short wave and thermal infrared hyperspectral imagers mounted on a personnel lift. During one of the early morning measurement sessions, a wispy, long linear trail was seen to emanate several meters from piles of explosives that were situated on the ground. Upon close visual inspection, it was observed that ants had found the piles of explosives and were carrying it to their ant hill, a distance of almost 20 meters from the piles. Initial analysis of the hyperspectral images clearly revealed the trail to the ant hill of explosives, despite being present in quantities not visible to the unaided eye. This paper details these observations and discusses them in the context of landmine and IED detection and neutralization. Possible reasons for such behaviour are presented. A number of questions regarding the behaviour, many pertinent to the use of ants in a counter-landmine/IED role, are presented and possible methods of answering them are discussed. Anecdotal evidence from deminers of detection and destruction of explosives by ants are presented.

  7. Explosion prevention in dry dust collection systems

    NASA Astrophysics Data System (ADS)

    Hokanson, J. C.; Magott, R. J.; Tranbarger, O.; Petino, G.; Seals, W. O.

    1983-01-01

    To reduce the risk of dust explosions in propellant and explosive manufacturing plants, dust is captured as it is generated and transported through ducts to filters, separators, or collectors. However, the dust collection systems may potentially contribute to the accident potential within the plant. A series of site visits was made to measure the electrostatic potential buildup and the dust concentration levels in ducting actually present during normal plant operations. These data provide a base of plant operating conditions upon which one may evaluate the safety of dry dust collection systems. A survey was conducted to determine if off-the-shelf instrumentation exists which will measure dust concentrations dynamically at levels within the explosive range. Most dust explosive characterizations are conducted using the Hartmann apparatus. This instrument is useful for evaluating relative characteristics of dusts. However, it has been shown that this instrument underpredicts both the peak pressure and the pressure rise rate for full-scale explosions. In designing explosion venting or explosion-resistant structures, data obtained in larger chambers are needed to allow the prediction of full-scale trends. A series of experiments was conducted using 40 and 1000 liter vessels to characterize the peak pressure and pressure rise rate for several explosive dusts.

  8. Advancing Explosives Detection Capabilities: Vapor Detection

    SciTech Connect

    Atkinson, David

    2012-10-15

    A new, PNNL-developed method provides direct, real-time detection of trace amounts of explosives such as RDX, PETN and C-4. The method selectively ionizes a sample before passing the sample through a mass spectrometer to detect explosive vapors. The method could be used at airports to improve aviation security.

  9. Explosive Joining for Nuclear-Reactor Repair

    NASA Technical Reports Server (NTRS)

    Bement, L. J.; Bailey, J. W.

    1983-01-01

    In explosive joining technique, adapter flange from fuel channel machined to incorporate a V-notch interface. Ribbon explosive, 1/2 inch (1.3 cm) in width, drives V-notched wall of adapter into bellows assembly, producing atomic-level metallurgical bond. Ribbon charge yields joint with double parent metal strength.

  10. Surface waves generated by shallow underwater explosions

    NASA Technical Reports Server (NTRS)

    Falade, A.; Holt, M.

    1978-01-01

    Surface water waves generated by surface and near surface point explosions are calculated. Taking the impulse distribution imparted at the water surface by the explosion as the overriding mechanism for transferring energy of the explosive to surface wave motion, the linearized theory of Kranzer and Keller is used to obtain the wave displacement in the far field. The impulse distribution is obtained by integrating the pressure wave over an appropriate time interval on a horizontal surface just beneath the undisturbed water surface. For surface explosions, a modified form of the similarity method first used by Collins and Holt is used to obtain the flow field. In the case of submerged explosions, the flow field is estimated by making necessary modifications to Sedov's similarity solution to account for the venting that accompanies the interaction of the leading (blast) wave with the ocean surface. Surface waves generated by a charge at six depths of placement (0.15 m, 0.30 m, 0.61 m, 0.91 m, 1.37 m, 3.05 m) are considered in addition to surface explosions. The results seem to support the existence of an upper critical depth phenomenon (of the type already established for chemical explosions) for point (nuclear) explosions.

  11. Explosive laser light initiation of propellants

    DOEpatents

    Piltch, M.S.

    1993-05-18

    A improved initiator for artillery shell using an explosively generated laser light to uniformly initiate the propellent. A small quantity of a high explosive, when detonated, creates a high pressure and temperature, causing the surrounding noble gas to fluoresce. This fluorescence is directed into a lasing material, which lases, and directs laser light into a cavity in the propellant, uniformly initiating the propellant.

  12. Redundant, Confined-Explosive Severance Device

    NASA Technical Reports Server (NTRS)

    Bement, Laurence J.; Schimmel, Morry L.

    1990-01-01

    Noncontaminating, long, explosive joint with highly reliable separation capability invented for such applications as separation of rocket-motor stages of spacecraft from rockets or Space Shuttle. Two explosive cords housed in tubes held in place by two notched doublers and commercially available fasteners. When either cord fired, its tube expands, bending doublers and causing fracture at adjacent notch.

  13. High-explosive driven crowbar switch

    DOEpatents

    Dike, Robert S.; Kewish, Jr., Ralph W.

    1976-01-13

    The disclosure relates to a compact explosive driven switch for use as a low resistance, low inductance crowbar switch. A high-explosive charge extrudes a deformable conductive metallic plate through a polyethylene insulating layer to achieve a hard current contact with a supportive annular conductor.

  14. Method for laser machining explosives and ordnance

    DOEpatents

    Muenchausen, Ross E.; Rivera, Thomas; Sanchez, John A.

    2003-05-06

    Method for laser machining explosives and related articles. A laser beam is directed at a surface portion of a mass of high explosive to melt and/or vaporize the surface portion while directing a flow of gas at the melted and/or vaporized surface portion. The gas flow sends the melted and/or vaporized explosive away from the charge of explosive that remains. The method also involves splitting the casing of a munition having an encased explosive. The method includes rotating a munition while directing a laser beam to a surface portion of the casing of an article of ordnance. While the beam melts and/or vaporizes the surface portion, a flow of gas directed at the melted and/or vaporized surface portion sends it away from the remaining portion of ordnance. After cutting through the casing, the beam then melts and/or vaporizes portions of the encased explosive and the gas stream sends the melted/vaporized explosive away from the ordnance. The beam is continued until it splits the article, after which the encased explosive, now accessible, can be removed safely for recycle or disposal.

  15. 30 CFR 7.306 - Explosion tests.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Explosion tests. 7.306 Section 7.306 Mineral... MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY Electric Motor Assemblies § 7.306 Explosion tests. (a... hydrocarbons, with the remainder being inert. At least 80 percent by volume of the gas shall be methane....

  16. 30 CFR 7.306 - Explosion tests.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Explosion tests. 7.306 Section 7.306 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY Electric Motor Assemblies § 7.306 Explosion tests. (a) The following shall be used...

  17. 30 CFR 7.100 - Explosion tests.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Explosion tests. 7.100 Section 7.100 Mineral... Underground Coal Mines Where Permissible Electric Equipment is Required § 7.100 Explosion tests. (a) Test procedures. (1) Prepare to test the diesel power package as follows: (i) Perform a detailed check of...

  18. Fire and explosion hazards of oil shale

    SciTech Connect

    Not Available

    1989-01-01

    The US Bureau of Mines publication presents the results of investigations into the fire and explosion hazards of oil shale rocks and dust. Three areas have been examined: the explosibility and ignitability of oil shale dust clouds, the fire hazards of oil shale dust layers on hot surfaces, and the ignitability and extinguishment of oil shale rubble piles. 10 refs., 54 figs., 29 tabs.

  19. 46 CFR 147.95 - Explosives.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 5 2014-10-01 2014-10-01 false Explosives. 147.95 Section 147.95 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) DANGEROUS CARGOES HAZARDOUS SHIPS' STORES Stowage and Other Special Requirements for Particular Materials § 147.95 Explosives. (a) Explosives—general. Except as provided for elsewhere in this...

  20. 30 CFR 7.100 - Explosion tests.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Explosion tests. 7.100 Section 7.100 Mineral... Underground Coal Mines Where Permissible Electric Equipment is Required § 7.100 Explosion tests. (a) Test procedures. (1) Prepare to test the diesel power package as follows: (i) Perform a detailed check of...

  1. 30 CFR 7.100 - Explosion tests.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Explosion tests. 7.100 Section 7.100 Mineral... Underground Coal Mines Where Permissible Electric Equipment is Required § 7.100 Explosion tests. (a) Test procedures. (1) Prepare to test the diesel power package as follows: (i) Perform a detailed check of...

  2. Glass produced by underground nuclear explosions. [Rainier

    SciTech Connect

    Schwartz, L.; Piwinskii, A.; Ryerson, F.; Tewes, H.; Beiriger, W.

    1983-01-01

    Detonation of an underground nuclear explosive produces a strong shock wave which propagates spherically outward, vaporizing the explosive and nearby rock and melting, the surrounding rock. The vaporized material expands adiabatically, forming a cavity. As the energy is dissipated during the cavity formation process, the explosive and rock debris condense and mix with the melted rock. The melt flows to the bottom of the cavity where it is quenched by fractured rock fragments falling from above as the cavity collapses. Measurements indicate that about 740 tonnes of rock and/or soil are melted for every kiloton (10/sup 12/ calories) of explosive energy, or about 25% of the explosive energy goes to melting rock. The resulting glass composition reflects the composition of the unaltered rock with explosive debris. The appearance ranges from white pumice to dense, dark lava. The bulk composition and color vary with the amount of explosive iron incorporated into the glass. The refractory explosion products are mixed with the solidified melt, although the degree of mixing is variable. Electron microprobe studies of glasses produced by Rainier in welded tuff have produced the following results: glasses are dehydrated relative to the host media, glasses are extremely heterogeneous on a 20 ..mu..m scale, a ubiquitous feature is the presence of dark marble-cake regions in the glass, which were locally enriched in iron and may be related to the debris, optically amorphous regions provide evidence of shock melting, only limited major element redistribution and homogenization occur within the cavity.

  3. Explosive laser light initiation of propellants

    DOEpatents

    Piltch, Martin S.

    1993-01-01

    A improved initiator for artillery shell using an explosively generated laser light to uniformly initiate the propellent. A small quantity of a high explosive, when detonated, creates a high pressure and temperature, causing the surrounding noble gas to fluoresce. This fluorescence is directed into a lasing material, which lases, and directs laser light into a cavity in the propellant, uniformly initiating the propellant.

  4. Sensitivity of solid explosives: Minimum energy of a dangerous impact

    NASA Technical Reports Server (NTRS)

    Afanasyev, G. T.

    1986-01-01

    A method which uses initiating explosives for determining the sensitivity of solid explosives is described. The energy index of sensitivity is determined by the mechanical properties of the explosives. The results of the calculations are discussed.

  5. Explosive stimulation of a geothermal well at the Geysers

    SciTech Connect

    Hanold, R.J.

    1980-01-01

    The use of an explosive in a vapor-dominated reservoir is discussed. The explosive and the present experimental plan are described. The explosive is HITEX II and some of its properties are listed. (MHR)

  6. Scaled experiments of explosions in cavities

    NASA Astrophysics Data System (ADS)

    Grun, J.; Cranch, G. A.; Lunsford, R.; Compton, S.; Walton, O. R.; Weaver, J.; Dunlop, W.; Fournier, K. B.

    2016-05-01

    Consequences of an explosion inside an air-filled cavity under the earth's surface are partly duplicated in a laboratory experiment on spatial scales 1000 smaller. The experiment measures shock pressures coupled into a block of material by an explosion inside a gas-filled cavity therein. The explosion is generated by suddenly heating a thin foil that is located near the cavity center with a short laser pulse, which turns the foil into expanding plasma, most of whose energy drives a blast wave in the cavity gas. Variables in the experiment are the cavity radius and explosion energy. Measurements and GEODYN code simulations show that shock pressures measured in the block exhibit a weak dependence on scaled cavity radius up to ˜25 m/kt1/3, above which they decrease rapidly. Possible mechanisms giving rise to this behavior are described. The applicability of this work to validating codes used to simulate full-scale cavity explosions is discussed.

  7. Explosive Vapor Detection Using Microcantilever Sensors

    SciTech Connect

    Pinnaduwage, Lal A

    2004-01-01

    MEMS-based microcantilever platforms have been used to develop extremely sensitive explosive vapour sensors. Two unique approaches of detecting of explosive vapours are demonstrated. In the first approach a cantilever beam coated with a selective layer undergoes bending and resonance frequency variation due to explosive vapour adsorption. The resonance frequency variation is due to mass loading while adsorption-induced cantilever bending is due to a differential stress due molecular adsorption. In the second approach that does not utilize selective coatings for speciation, detection is achieved by deflagration of adsorbed explosive molecules. Deflagration of adsorbed explosive molecules causes the cantilever to bend due to released heat while its resonance frequency decreases due to mass unloading.

  8. Morphomechanical Innovation Drives Explosive Seed Dispersal.

    PubMed

    Hofhuis, Hugo; Moulton, Derek; Lessinnes, Thomas; Routier-Kierzkowska, Anne-Lise; Bomphrey, Richard J; Mosca, Gabriella; Reinhardt, Hagen; Sarchet, Penny; Gan, Xiangchao; Tsiantis, Miltos; Ventikos, Yiannis; Walker, Simon; Goriely, Alain; Smith, Richard; Hay, Angela

    2016-06-30

    How mechanical and biological processes are coordinated across cells, tissues, and organs to produce complex traits is a key question in biology. Cardamine hirsuta, a relative of Arabidopsis thaliana, uses an explosive mechanism to disperse its seeds. We show that this trait evolved through morphomechanical innovations at different spatial scales. At the organ scale, tension within the fruit wall generates the elastic energy required for explosion. This tension is produced by differential contraction of fruit wall tissues through an active mechanism involving turgor pressure, cell geometry, and wall properties of the epidermis. Explosive release of this tension is controlled at the cellular scale by asymmetric lignin deposition within endocarp b cells-a striking pattern that is strictly associated with explosive pod shatter across the Brassicaceae plant family. By bridging these different scales, we present an integrated mechanism for explosive seed dispersal that links evolutionary novelty with complex trait innovation. VIDEO ABSTRACT. PMID:27264605

  9. Detonation in shocked homogeneous high explosives

    SciTech Connect

    Yoo, C.S.; Holmes, N.C.; Souers, P.C.

    1995-11-01

    We have studied shock-induced changes in homogeneous high explosives including nitromethane, tetranitromethane, and single crystals of pentaerythritol tetranitrate (PETN) by using fast time-resolved emission and Raman spectroscopy at a two-stage light-gas gun. The results reveal three distinct steps during which the homogeneous explosives chemically evolve to final detonation products. These are (1) the initiation of shock compressed high explosives after an induction period, (2) thermal explosion of shock-compressed and/or reacting materials, and (3) a decay to a steady-state representing a transition to the detonation of uncompressed high explosives. Based on a gray-body approximation, we have obtained the CJ temperatures: 3800 K for nitromethane, 2950 K for tetranitromethane, and 4100 K for PETN. We compare the data with various thermochemical equilibrium calculations. In this paper we will also show a preliminary result of single-shot time-resolved Raman spectroscopy applied to shock-compressed nitromethane.

  10. Independence day explosion on lovers key.

    PubMed

    Harding, Brett A; Wolf, Barbara C

    2007-09-01

    The display of fireworks is a popular holiday celebration in the United States. Because injuries due to recreational fireworks-related explosions among private consumers are relatively common, the sale of fireworks is regulated by the federal government and is also limited by state and local laws. In contrast, because fireworks display companies are under tight safety regulations, explosions in the professional pyrotechnics industry are uncommon occurrences, and the literature contains rare reports of injuries and fatalities resulting from such explosions. We report the 2003 Fourth of July commercial fireworks explosion on Lovers Key in southwest Florida that resulted in five fatalities. Events occurring during the investigation of the scene of this explosion illustrate the unique considerations and hazards for medicolegal death investigators, law enforcement and other investigative agencies. Additionally, this case demonstrates unusual aspects of the postmortem examinations performed on victims of fireworks-related incidents. PMID:17767662

  11. Explosives remain preferred methods for platform abandonment

    SciTech Connect

    Pulsipher, A.; Daniel, W. IV; Kiesler, J.E.; Mackey, V. III

    1996-05-06

    Economics and safety concerns indicate that methods involving explosives remain the most practical and cost-effective means for abandoning oil and gas structures in the Gulf of Mexico. A decade has passed since 51 dead sea turtles, many endangered Kemp`s Ridleys, washed ashore on the Texas coast shortly after explosives helped remove several offshore platforms. Although no relationship between the explosions and the dead turtles was ever established, in response to widespread public concern, the US Minerals Management Service (MMS) and National Marine Fisheries Service (NMFS) implemented regulations limiting the size and timing of explosive charges. Also, more importantly, they required that operators pay for observers to survey waters surrounding platforms scheduled for removal for 48 hr before any detonations. If observers spot sea turtles or marine mammals within the danger zone, the platform abandonment is delayed until the turtles leave or are removed. However, concern about the effects of explosives on marine life remains.

  12. [Explosion injuries - prehospital care and management].

    PubMed

    Holsträter, Thorsten; Holsträter, Susanne; Rein, Daniela; Helm, Matthias; Hossfeld, Björn

    2013-11-01

    Explosion injuries are not restricted to war-like military conflicts or terrorist attacks. The emergency physician may also encounter such injuries in the private or industrial fields, injuries caused by fireworks or gas explosions. In such cases the injury patterns are especially complex and may consist of blunt and penetrating injuries as well as thermal damage. Emergency medical personnel must be prepared to cope with explosion trauma not only in individual cases but also in major casualty incidents (MCI). This necessitates a sound knowledge about the mechanisms and processes of an explosion as well as the particular pathophysiological relationships of explosion injuries in order to be able to initiate the best possible, guideline-conform trauma therapy. PMID:24343140

  13. Understanding ultrafine nanodiamond formation using nanostructured explosives

    PubMed Central

    Pichot, Vincent; Risse, Benedikt; Schnell, Fabien; Mory, Julien; Spitzer, Denis

    2013-01-01

    The detonation process is able to build new materials with a bottom-up approach. Diamond, the hardest material on earth, can be synthesized in this way. This unconventional synthesis route is possible due to the presence of carbon inside the high-explosive molecules: firing high-explosive mixtures with a negative oxygen balance in a non-oxidative environment leads to the formation of nanodiamond particles. Trinitrotoluene (TNT) and hexogen (RDX) are the explosives primarily used to synthesize nanodiamonds. Here we show that the use of nanostructured explosive charges leads to the formation of smaller detonation nanodiamonds, and it also provides new understanding of nanodiamond formation-mechanisms. The discontinuity of the explosive at the nanoscale level plays the key role in modifying the diamond particle size, and therefore varying the size with microstructured charges is impossible. PMID:23831716

  14. Prise en charge en soins primaires des troubles liés à l’usage d’alcool et de la consommation à risque

    PubMed Central

    Spithoff, Sheryl; Kahan, Meldon

    2015-01-01

    Résumé Objectif Fournir aux médecins de soins primaires de l’information et des conseils fondés sur des données probantes sur le dépistage et l’évaluation de la consommation d’alcool à risque et des troubles liés à l’usage d’alcool (TUA). Sources des données Nous avons effectué une recherche documentaire non systématique en utilisant des expressions de recherche portant sur les soins primaires, les TUA, la dépendance à l’alcool, l’abus d’alcool, l’usage abusif d’alcool, la consommation d’alcool néfaste pour la santé, ainsi que le dépistage, la détermination et l’évaluation dans le contexte des soins primaires. Principaux messages Les médecins de famille devraient faire passer un test validé de dépistage de l’abus d’alcool à tous les patients, au moins une fois par année. Dépister les patients qui se présentent avec des problèmes médicaux ou psychosociaux pouvant être reliés à l’usage d’alcool. Déterminer si les patients qui obtiennent des résultats positifs lors du dépistage sont des consommateurs d’alcool à risque ou s’ils ont des TUA. Si les patients ont des TUA, déterminer si les troubles sont légers, modérés ou sévères en utilisant les critères de la 5e édition du Manuel diagnostique et statistique des troubles mentaux. Communiquer le diagnostic aux patients et leur offrir de l’aide. Effectuer une évaluation plus approfondie des patients ayant des TUA. Procéder à un dépistage de la consommation d’autres substances, des troubles concomitants et des traumatismes. Déterminer s’il est nécessaire de rapporter le cas aux services de protection de l’enfance ou au ministère des Transports. Déterminer les besoins en matière de prise en charge médicale du sevrage alcoolique. Effectuer un bref examen physique et prescrire l’exécution de tests de laboratoire pour évaluer la formule sanguine complète et les taux de transaminases hépatiques, comprenant les

  15. L’opinion des étudiants en médecine de Québec sur les punitions corporelles

    PubMed Central

    Labbé, Jean; Laflamme, Nathalie; Makosso-Kallyth, Sun

    2012-01-01

    OBJECTIF : L’objectif de la présente étude est de décrire l’opinion des étudiants en médecine de l’Université Laval sur le sujet controversé des punitions corporelles envers les enfants. MÉTHODOLOGIE : Un sondage a été réalisé auprès des étudiants en quatrième année de médecine de l’Université Laval pendant cinq années consécutives, soit de l’année scolaire 2006–2007 jusqu’à celle de 2010–2011 inclusivement, à l’occasion d’un séminaire portant sur la maltraitance envers les enfants. RÉSULTATS : Sur les 712 étudiants interrogés, 74 % étaient de sexe féminin et 91 % étaient âgés de moins de 30 ans. Concernant les punitions corporelles envers les enfants, 22 % des répondants s’y sont déclarés favorables. Plus de garçons que de filles se sont prononcés en faveur de cette pratique disciplinaire, soit 31 % des garçons par rapport à 18 % des filles respectivement (RC rajusté = 2,2, IC 95 % :1,4 à 3,4; p=0,0003). Près de 36 % des étudiants ayant eu des punitions corporelles y étaient favorables, comparativement à seulement 4 % de ceux qui n’avaient pas connu cette forme de discipline (RC rajusté = 16,5, IC 95 % :8,6 à 31,4; p<0,0001). Parmi ceux qui ont mentionné avoir été victimes d’abus physique, 25 % se sont déclarés en faveur de cette pratique, ce qui est similaire au 21 % observés chez ceux qui n’en ont pas été victimes (p=0,52). CONCLUSION : Alors que plusieurs organismes médicaux se sont prononcés contre l’utilisation des punitions corporelles, plus d’un futur médecin sur cinq à Québec se déclare favorable à cette méthode disciplinaire et pourrait influencer la conduite des parents en ce sens. PMID:24179417

  16. Method for fabricating non-detonable explosive simulants

    DOEpatents

    Simpson, Randall L.; Pruneda, Cesar O.

    1995-01-01

    A simulator which is chemically equivalent to an explosive, but is not detonable. The simulator has particular use in the training of explosives detecting dogs and calibrating sensitive analytical instruments. The explosive simulants may be fabricated by different techniques, a first involves the use of standard slurry coatings to produce a material with a very high binder to explosive ratio without masking the explosive vapor, and the second involves coating inert beads with thin layers of explosive molecules.

  17. Method for fabricating non-detonable explosive simulants

    DOEpatents

    Simpson, R.L.; Pruneda, C.O.

    1995-05-09

    A simulator is disclosed which is chemically equivalent to an explosive, but is not detonable. The simulator has particular use in the training of explosives detecting dogs and calibrating sensitive analytical instruments. The explosive simulants may be fabricated by different techniques, a first involves the use of standard slurry coatings to produce a material with a very high binder to explosive ratio without masking the explosive vapor, and the second involves coating inert beads with thin layers of explosive molecules. 5 figs.

  18. Biodegradation and biotransformation of explosives.

    PubMed

    Rylott, Elizabeth L; Lorenz, Astrid; Bruce, Neil C

    2011-06-01

    Explosives now contaminate millions of hectares of land in the US alone, with global levels of contamination difficult to fully assess. Understanding the biology behind the metabolism of these toxic compounds by microorganisms and plants is imperative for managing these pollutants in the environment. Towards this aim, recent studies have identified, and are now characterizing, plant genes involved in 2,4,6-trinitrotoluene detoxification and the biochemical pathways of nitramine degradation in microorganisms. A key scientific goal continues to be identification of enzymes capable of degrading 2,4,6-trinitrotoluene and this still remains elusive, although recent reports give insights into the origin of nitrite released during biotransformation of this major contaminant. Promising phytoremediation research using transgenic model plant systems has now been transferred to poplar, a species with field applicability. PMID:21094036

  19. Nuclear explosives testing readiness evaluation

    SciTech Connect

    Valk, T.C.

    1993-09-01

    This readiness evaluation considers hole selection and characterization, verification, containment issues, nuclear explosive safety studies, test authorities, event operations planning, canister-rack preparation, site preparation, diagnostic equipment setup, device assembly facilities and processes, device delivery and insertion, emplacement, stemming, control room activities, readiness briefing, arming and firing, test execution, emergency response and reentry, and post event analysis to include device diagnostics, nuclear chemistry, and containment. This survey concludes that the LLNL program and its supporting contractors could execute an event within six months of notification, and a second event within the following six months, given the NET group`s evaluation and the following three restraints: (1) FY94 (and subsequent year) funding is essentially constant with FY93, (2) Preliminary work for the initial event is completed to the historical sic months status, (3) Critical personnel, currently working in dual use technologies, would be recallable as needed.

  20. Ionospheric effects of supernova explosions

    NASA Astrophysics Data System (ADS)

    Edwards, P. J.

    Possible ionospheric effects of supernova explosions are considered, with special attention given to those of SN 1987a. Results are presented on the calculations of anticipated X-ray/UV flare parameters, including the shock temperature, the minimum flare duration, the average photon energy, and the shock-front travel time for a range of stellar radii bracketing SK 202-69, which was identified by White Malin (1987) as the progenitor star for SN 1987a. It is shown that the characteristics of the X-ray/UV flare are strongly influenced by the radius of the shock wave breakout, so that the flare from SN 1987a can be anticipated to have characteristics intermediate between those attributed to compact stars and stars with extended envelopes.

  1. Explosion probability of unexploded ordnance: expert beliefs.

    PubMed

    MacDonald, Jacqueline Anne; Small, Mitchell J; Morgan, M G

    2008-08-01

    This article reports on a study to quantify expert beliefs about the explosion probability of unexploded ordnance (UXO). Some 1,976 sites at closed military bases in the United States are contaminated with UXO and are slated for cleanup, at an estimated cost of $15-140 billion. Because no available technology can guarantee 100% removal of UXO, information about explosion probability is needed to assess the residual risks of civilian reuse of closed military bases and to make decisions about how much to invest in cleanup. This study elicited probability distributions for the chance of UXO explosion from 25 experts in explosive ordnance disposal, all of whom have had field experience in UXO identification and deactivation. The study considered six different scenarios: three different types of UXO handled in two different ways (one involving children and the other involving construction workers). We also asked the experts to rank by sensitivity to explosion 20 different kinds of UXO found at a case study site at Fort Ord, California. We found that the experts do not agree about the probability of UXO explosion, with significant differences among experts in their mean estimates of explosion probabilities and in the amount of uncertainty that they express in their estimates. In three of the six scenarios, the divergence was so great that the average of all the expert probability distributions was statistically indistinguishable from a uniform (0, 1) distribution-suggesting that the sum of expert opinion provides no information at all about the explosion risk. The experts' opinions on the relative sensitivity to explosion of the 20 UXO items also diverged. The average correlation between rankings of any pair of experts was 0.41, which, statistically, is barely significant (p= 0.049) at the 95% confidence level. Thus, one expert's rankings provide little predictive information about another's rankings. The lack of consensus among experts suggests that empirical studies

  2. Probabilistic modeling of propagating explosions

    SciTech Connect

    Luck, L.B.; Eisenhawer, S.W.; Bott, T.F.

    1996-03-01

    Weapons containing significant quantities of high explosives (HE) are sometimes located in close proximity to one another. If an explosion occurs in a weapon, the possibility of propagation to one or more additional weapons may exist, with severe consequences possibly resulting. In the general case, a system of concern consists of multiple weapons and various other objects in a complex, three-dimensional geometry. In each weapon, HE is enclosed by (casing) materials that function as protection in the event of a neighbor detonation but become a source of fragments if the HE is initiated. The protection afforded by the casing means that only high-momentum fragments, which occur rarely, are of concern. These fragments, generated in an initial donor weapon are transported to other weapons either directly or by ricochet. Interaction of a fragment with an acceptor weapon can produce a reaction in the acceptor HE and result in a second detonation. In this paper we describe a comprehensive methodology to estimate the probability of various consequences for fragment-induced propagating detonations in arrays of weapons containing HE. Analysis of this problem requires an approach that can both define the circumstances under which rare events can occur and calculate the probability of such occurrences. Our approach is based on combining process tree methodology with Monte Carlo transport simulation. Our Monte Carlo technique very effectively captures important features of these differences. Process tree methodology is described and its use is discussed for a simplified problem and to illustrate the power of Monte Carlo simulation in estimating fragment-induced detonation of an acceptor weapon.

  3. Ignition dynamics of high explosives

    SciTech Connect

    Ali, A.N.; Son, S.F.; Sander, R.K.; Asay, B.W.

    1998-12-31

    Mechanical insults of granular high explosives (HE) can result in localized areas of elevated temperature, or hot spots. The evolution of these hot spots is a central issue of HE science. Because of the complexity involved, it is worthwhile to study mechanical and reaction processes in isolation. Mechanical processes are isolated and studied using inert materials or weak insults where reaction may be minimal. Likewise, purely thermal processes can be considered to isolate HE reaction response. In this work the authors study the radiant ignition of various HEs of interest, including HMX (C{sub 4}H{sub 8}N{sub 8}O{sub 8}), PBX 9501 (95% HMX, 2.5% Estane, 2.5% BDNPA/BDNPF), RDX (C{sub 3}H{sub 6}N{sub 6}O{sub 6}), TATB (C{sub 6}H{sub 6}N{sub 6}O{sub 6}), and PBX 9502 (95% TATB, 5% Kel-F) and aged PBX 9502. Initial work has included unconfined samples at ambient pressure in air. Diagnostics have included photodiodes to record first light emission, high speed photography, microthermocouple and IR emission measurement to obtain surface temperature, IR emission of gases above the pellet, and a novel nonlinear optical technique to characterize the dynamic {beta}-{delta} solid phase transformation and the formation of a liquid layer. The authors find that ignition delays at various power levels is very similar for HMX and RDX; except that the minimum radiant flux needed for RDX ignition is higher. The addition of only 5% binder (PBX 9501) causes significantly longer ignition delays at lower heat fluxes compared with HMX alone. TATB and TATB-based explosives exhibit much longer ignition delays than HMX. In contrast to HMX, however, no measurable difference is observed in TATB by the addition of a binder (PBX 9502, aged or pristine).

  4. Ignition dynamics of high explosives

    SciTech Connect

    Ali, A.N.; Son, S.F.; Sander, R.K.; Asay, B.W.; Brewster, M.Q.

    1999-04-01

    The laser ignition of the explosives HMX (octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine, C{sub 4}H{sub 8}N{sub 8}O{sub 8}), {delta}-phase HMX, PBX 9501 (95% HMX, 2.5% Estane, 2.5% BDNPA/BDNPF), TATB (1,3,5-triamino-2,4,6-trinitrobenzene, C{sub 6}H{sub 6}N{sub 6}O{sub 6}), and PBX 9502 (95% TATB, 5% Kel-F) and aged PBX 9502 has been conducted with the intent to compare the relative sensitivities of those explosives and to investigate the effect of beam profile, binder addition, and porosity. It has been found that there was little difference between a gaussian beam and a top hat profile on the laser ignition of HMX. The authors observe that the addition of binder in the amounts present in PBX 9501 resulted in longer ignition delays than that of HMX. In contrast to HMX, the addition of binder to TATB in PBX 9502 shows no measurable effect. Porosity effects were considered by comparing the ignition of granular HMX and pressed HMX pellets. Porosity appears to increase ignition delay due to an increased effective absorption scale and increased convective heat loss. This porosity effect also resulted in longer ignition delays for {delta}-phase HMX than for {beta}-phase HMX. In order to simulate ignition in voids or cracks, the standard ignition experiment was modified to include a NaCl window placed at variable distances above the sample surface. When ignition experiments were performed at 29 W/cm{sup 2} and 38 W/cm{sup 2} a critical gap distance was observed of 6 {+-} 0.4 mm below which ignition was severely inhibited. This result underscores the importance of gas phase processes in ignition and illustrates that conditions can exist where simple ignition criteria such as surface temperature is inadequate.

  5. Chemical analysis kit for the presence of explosives

    SciTech Connect

    Eckels, Joel Del; Nunes; Peter J.; Alcaraz, Armando; Whipple, Richard E.

    2011-05-10

    A tester for testing for explosives associated with a test location comprising a first explosives detecting reagent; a first reagent holder, the first reagent holder containing the first explosives detecting reagent; a second explosives detecting reagent; a second reagent holder, the second reagent holder containing the second explosives detecting reagent; a sample collection unit for exposure to the test location, exposure to the first explosives detecting reagent, and exposure to the second explosives detecting reagent; and a body unit containing a heater for heating the sample collection unit for testing the test location for the explosives.

  6. 27 CFR 555.109 - Identification of explosive materials.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... Business or Operations § 555.109 Identification of explosive materials. (a) General. Explosive materials... in the English language, using Roman letters and Arabic numerals. (3) Licensed manufacturers...

  7. Study on metal foil explosion using high current

    NASA Astrophysics Data System (ADS)

    Mihara, Takayuki; Matsuo, N.; Otsuka, M.; Itoh, S.

    2009-12-01

    In the high energy processing using explosive, there are variety of application examples which is explosion welding of differential metallic plate and powder compaction of diamond. However a rule legal to explosives is severe and needs many efforts for handling qualification acquisition, maintenance, and security. In this research, the metallic foil explosion using high current is paid my attention to the method to obtain linear or planate explosive initiation easily, and the main evaluation of metallic foil explosion was conducted. The explosion power was evaluated by observing optically the underwater shock wave generated from the metallic foil explosion.

  8. Study on metal foil explosion using high current

    NASA Astrophysics Data System (ADS)

    Mihara, Takayuki; Matsuo, N.; Otsuka, M.; Itoh, S.

    2010-03-01

    In the high energy processing using explosive, there are variety of application examples which is explosion welding of differential metallic plate and powder compaction of diamond. However a rule legal to explosives is severe and needs many efforts for handling qualification acquisition, maintenance, and security. In this research, the metallic foil explosion using high current is paid my attention to the method to obtain linear or planate explosive initiation easily, and the main evaluation of metallic foil explosion was conducted. The explosion power was evaluated by observing optically the underwater shock wave generated from the metallic foil explosion.

  9. Pixelated diffraction signatures for explosive detection

    NASA Astrophysics Data System (ADS)

    O'Flynn, Daniel; Reid, Caroline; Christodoulou, Christiana; Wilson, Matt; Veale, Matthew C.; Seller, Paul; Speller, Robert

    2012-06-01

    Energy dispersive X-ray diffraction (EDXRD) is a technique which can be used to improve the detection and characterisation of explosive materials. This study has performed EDXRD measurements of various explosive compounds using a novel, X-ray sensitive, pixelated, energy resolving detector developed at the Rutherford Appleton Laboratory, UK (RAL). EDXRD measurements are normally performed at a fixed scattering angle, but the 80×80 pixel detector makes it possible to collect both spatially resolved and energy resolved data simultaneously. The detector material used is Cadmium Telluride (CdTe), which can be utilised at room temperature and gives excellent spectral resolution. The setup uses characteristics from both energy dispersive and angular dispersive scattering techniques to optimise specificity and speed. The purpose of the study is to develop X-ray pattern "footprints" of explosive materials based on spatial and energy resolved diffraction data, which can then be used for the identification of such materials hidden inside packages or baggage. The RAL detector is the first energy resolving pixelated detector capable of providing an energy resolution of 1.0-1.5% at energies up to 150 keV. The benefit of using this device in a baggage scanner would be the provision of highly specific signatures to a range of explosive materials. We have measured diffraction profiles of five explosives and other compounds used to make explosive materials. High resolution spectra have been obtained. Results are presented to show the specificity of the technique in finding explosives within baggage.

  10. Simulating Thermal Explosion of Octahydrotetranitrotetrazine-based explosives: Model Comparison with Experiment

    SciTech Connect

    Yoh, J J; McClelland, M A; Maienschein, J L; Nichols, A L; Tarver, C M

    2006-02-07

    The authors compare two-dimensional model results with measurements for the thermal, chemical and mechanical behavior in a thermal explosion experiment. Confined high explosives are heated at a rate of 1 C per hour until an explosion is observed. The heating, ignition, and deflagration phases are modeled using an Arbitrarily Lagrangian-Eulerian code (ALE3D) that can handle a wide range of time scales that vary from a structural to a dynamic hydro time scale. During the pre-ignition phase, quasi-static mechanics and diffusive thermal transfer from a heat source to the HE are coupled with the finite chemical reactions that include both endothermic and exothermic processes. Once the HE ignites, a hydro dynamic calculation is performed as a burn front propagates through the HE. Two octahydrotetranitrotetrazine (HMX)-based explosives, LX-04 and LX-10, are considered, whose chemical-thermal-mechanical models are constructed based on measurements of thermal and mechanical properties along with small scale thermal explosion measurements. The present HMX modeling work shows very first violence calculations with thermal predictions associated with a confined thermal explosion test. The simulated dynamic response of HE confinement during the explosive phase is compared to measurements in larger scale thermal explosion tests. The explosion temperatures for both HE's are predicted to within 1 C. Calculated and measured wall strains provide an indication of vessel pressurization during the heating phase and violence during the explosive phase.

  11. Identification des risques professionnels dans l'industrie textile en République Démocratique du Congo

    PubMed Central

    Kitronza, Panda Lukongo

    2014-01-01

    Introduction Le but de cette étude est de mettre en évidence les facteurs de risques professionnels liés aux conditions de travail. Méthodes Cette étude qualitative basée sur les entretiens de groupe a été réalisée par une équipe pluridisciplinaire dans l'industrie textile de la région du Est de la RDC; comprenant un médecin de travail, un médecin de santé publique, un toxicologue, deux infirmiers du centre hospitalier de l'usine, un représentant du comité d'hygiène et un technicien de prévention. La démarche méthodologique a consisté en des entretiens en groupe, des observations et visites guidées de lieux de travail de l'entreprise. Résultats Dans la culture du coton, les effets d'une forte exposition aux pesticides peuvent entraîner des intoxications aiguës, chroniques et voire le décès. Les autres risques sont les accidents de travail, les maladies professionnelles, les troubles psychologiques. Dans l'industrie, les travailleurs sont exposés aux risques liés à l'empoussiérage des fibres de coton, aux facteurs des risques traumatiques, physiques (bruits, vibration) et chimiques (acides forts, bases fortes, solvants et colorants minéraux), ainsi qu'aux risques psychosociaux. La pollution de l'environnement et l’écotoxicité inhérente à ces activités restent l'effet de l'usage des grandes quantités d'intrants agricoles, engrais et produits phytosanitaires. Conclusion Cette étude a permis de mettre en évidence les différents facteurs de risques auxquelles sont soumis les travailleurs textiles; ainsi que les risques environnementaux liés à cette activité. Cela est de nature à permettre la mise sur pied d'une stratégie efficace de prévention et de protection des travailleurs. PMID:25977736

  12. Concussive brain injury from explosive blast

    PubMed Central

    de Lanerolle, Nihal C; Hamid, Hamada; Kulas, Joseph; Pan, Jullie W; Czlapinski, Rebecca; Rinaldi, Anthony; Ling, Geoffrey; Bandak, Faris A; Hetherington, Hoby P

    2014-01-01

    Objective Explosive blast mild traumatic brain injury (mTBI) is associated with a variety of symptoms including memory impairment and posttraumatic stress disorder (PTSD). Explosive shock waves can cause hippocampal injury in a large animal model. We recently reported a method for detecting brain injury in soldiers with explosive blast mTBI using magnetic resonance spectroscopic imaging (MRSI). This method is applied in the study of veterans exposed to blast. Methods The hippocampus of 25 veterans with explosive blast mTBI, 20 controls, and 12 subjects with PTSD but without exposure to explosive blast were studied using MRSI at 7 Tesla. Psychiatric and cognitive assessments were administered to characterize the neuropsychiatric deficits and compare with findings from MRSI. Results Significant reductions in the ratio of N-acetyl aspartate to choline (NAA/Ch) and N-acetyl aspartate to creatine (NAA/Cr) (P < 0.05) were found in the anterior portions of the hippocampus with explosive blast mTBI in comparison to control subjects and were more pronounced in the right hippocampus, which was 15% smaller in volume (P < 0.05). Decreased NAA/Ch and NAA/Cr were not influenced by comorbidities – PTSD, depression, or anxiety. Subjects with PTSD without blast had lesser injury, which tended to be in the posterior hippocampus. Explosive blast mTBI subjects had a reduction in visual memory compared to PTSD without blast. Interpretation The region of the hippocampus injured differentiates explosive blast mTBI from PTSD. MRSI is quite sensitive in detecting and localizing regions of neuronal injury from explosive blast associated with memory impairment. PMID:25493283

  13. Etude des aspects cliniques, échographiques et nutritionnels du syndrome des ovaires micropolykystiques (SOMPK) à Mbuji-Mayi, RD du Congo

    PubMed Central

    Kalenda, Louis Mbuyamba Ntobo; Mikenji, Justin Biayi; Nkoy, Albert Mwembo-Tambwe; Kayamba, Prosper Kalenga Muenze

    2014-01-01

    Introduction Le Syndrome des Ovaires Micropolykystiques (SOMPK) est polymorphe. L'objectif de cette étude était de déterminer la prévalence et rechercher les facteurs nutritionnels éventuellement associés. Méthodes Chez 300 patientes atteintes de SOMPK faisant l'objet de cette étude, les données anamnestiques, cliniques et échographiques, et les habitudes alimentaires ont été analysées. Les statistiques usuelles et les mesures d'association ont été utilisées pour analyser les résultats. Résultats La prévalence de SOMPK était de 23,6%. L’âge moyen des patientes avec SOMPK était 24 ± 7 ans et chez celles sans SOMPK 36 ± 7 ans (P < 0,05). Le risque de développer le SOMPK en présence d'un niveau de vie élevé était de 2,03 (RR = 2,03; IC à 95%: 1,73-2,38; P = 0,00). Le risque de développer le SOMPK en exerçant une activité légère est de 2,15 (RR = 2,15; IC à 95%: 1,87-2,87; P= 0,00). La proportion des patientes avec SOMPK ayant accumulé plus de 2400 kcal était de 59% vs 36% (P < 0,05) et le risque de développer le SOMPK lorsque l’énergie accumulée était supérieure à 2400 kcal était de 1,57 (RR = 1,57; IC à 95%: 1,33-1,85; P= 0,00). Conclusion Dans notre milieu la prévalence de SOMPK était de 23,6%. Les facteurs associés au SOMPK étaient l’âge, l’énergie accumulée de plus de 2400 Kcal, le niveau socio-économique élevé et l'activité physique légère. Des études analytiques plus poussées sont nécessaires, pour évaluer la force du risque que représentent ces différents facteurs étudiés. PMID:25870722

  14. The nucleation mechanism of wire explosion

    NASA Astrophysics Data System (ADS)

    Tkachenko, S. I.; Vorob'ev, V. S.; Malyshenko, S. P.

    2004-02-01

    This study deals with the nucleation mechanism of electric explosion of wires allowing estimation of wire parameters at the start of the explosion for a wide range of experimental conditions. We analyse the dependence of the limit value of the energy deposited during the initial resistive phase of heating of the wire on the parameters of the wire and circuit as well as the size distribution of metal particles formed on electrical explosion of the wire. We discuss the correspondence of these results with previously published experimental data.

  15. Electrical effects generated by experimental volcanic explosions

    SciTech Connect

    Buettner, R.; Roeder, H.; Zimanowski, B.

    1997-04-01

    We report on the experimental study of electrical phenomena during explosive volcanic eruptions, which provides qualitative and quantitative insight into different fragmentation and eruption mechanisms of magmatic melt. The experiments show that air friction and surface enlargement by hydro- and/or aerodynamic magma fragmentation are only minor contributors to electrical charging of erupted particle clouds in comparison to thermo-hydraulic fracturing of magma by explosive magma/water interaction. This process has the potency to explain the frequently observed occurrence of lightning in eruption clouds of explosive volcanic events. {copyright} {ital 1997 American Institute of Physics.}

  16. On the Violence of High Explosive Reactions

    SciTech Connect

    Tarver, C M; Chidester, S K

    2004-02-09

    High explosive reactions can be caused by three general energy deposition processes: impact ignition by frictional and/or shear heating; bulk thermal heating; and shock compression. The violence of the subsequent reaction varies from benign slow combustion to catastrophic detonation of the entire charge. The degree of violence depends on many variables, including the rate of energy delivery, the physical and chemical properties of the explosive, and the strength of the confinement surrounding the explosive charge. The current state of experimental and computer modeling research on the violence of impact, thermal, and shock-induced reactions is reviewed.

  17. Explosives detection: a challenge for physical chemistry.

    PubMed

    Steinfeld, J I; Wormhoudt, J

    1998-01-01

    The detection of explosives, energetic materials, and their associated compounds for security screening, demining, detection of unexploded ordnance, and pollution monitoring is an active area of research. A wide variety of detection methods and an even wider range of physical chemistry issues are involved in this very challenging area. This review focuses on techniques such as optical and mass spectrometry and chromatography for detection of trace amounts of explosives with short response times. We also review techniques for detecting the decomposition fragments of these materials. Molecular data for explosive compounds are reviewed where available. PMID:15012428

  18. Explosive fragmentation of orbiting propellant tanks

    NASA Technical Reports Server (NTRS)

    Benz, F. J.; Kays, R. L.; Bishop, C. V.; Eck, M. B.

    1989-01-01

    An examination is made of the in-orbit explosive characteristics of the Delta second stage and Ariane third stage, with a view to the vehicle breakups of the Ariane SPOT third-stage fuel tank in November, 1986, and of two Delta second stage tanks. Attention is given to the possible role of residual propellants in these breakups. After reviewing orbital data and comparing predicted fragment velocities with observed fragment velocities in debris patterns, a comparison has been made of total debris energy with total calculated explosion energy. Both physical and chemical explosions are deemed possible.

  19. Simulation of collisional fragmentation with explosives

    NASA Technical Reports Server (NTRS)

    Housen, Kevin

    1993-01-01

    For practical reasons, experimental studies of collisional fragmentation must at times rely on explosives to fragment a target body. For example, Housen et al., described experiments in which spheres were fragmented in a pressurized atmosphere. Explosives were used because impacts could not be performed in the pressure chamber. Explosives can also be used to study targets much larger than those which can be disrupted by conventional light-gas guns, thereby allowing size- and rate-effects to be investigated. The purpose of this study is to determine the charge burial depth required to simulate various aspects of collisions.

  20. Simplified Explosive Joining of Tubes to Fittings

    NASA Technical Reports Server (NTRS)

    Bement, L. J.; Bailey, J. W.; Perry, R.; Finch, M. S.

    1987-01-01

    Technique simplifies tube-to-fitting joining, as compared to fusion welding, and provides improvement on standard procedures used to join tubes explosively to tube fittings. Special tool inserted into tube to be joined. Tool allows strip of ribbon explosive to be placed right at joint. Ribbon explosive and mild detonating fuse allows use of smaller charge. Assembled tool storable, and process amenable to automation. Assembly of components, insertion of tool into weld site, and joining operation mechanized without human contact. Used to assemble components in nuclear reactors or in other environments hostile to humans.

  1. Explosion Shear Wave Generation and Scattering

    NASA Astrophysics Data System (ADS)

    Baker, G. E.; Stevens, J. L.; Xu, H.

    2004-12-01

    We use observations of explosion-generated Lg together with three separate types of numerical models to determine how underground nuclear explosions generate shear wave phases. This question is fundamental to how Lg phases are interpreted for use in explosion yield estimation and earthquake/explosion discrimination. A simple point explosion in a uniform medium generates no shear waves, so the Lg phase is generated entirely by non-spherical components of the source and conversions through reflections and scattering. Our results indicate that the most important sources of high frequency explosion shear waves are P to S conversions at the free surface and S waves generated directly by a realistic distributed explosion source including nonlinear effects due to the free surface and gravity. In addition, Rg scattering may contribute to lower frequency Lg. Near source S is observed on both radial and tangential component records from a diverse set of explosion data. The data sets include 1) Degelen Mountain explosions recorded at distances less than 100 km and corresponding recordings at Borovoye (BOR) at 650 km; 2) recordings from Russian deep seismic sounding experiments; 3) Nevada Test Site (NTS) explosion sources including the Nonproliferation Experiment (NPE) and nuclear tests covering a range of source depths and media properties. We model the overburied NPE, and underburied and overburied Degelen explosions, using point sources and two-dimensional nonlinear finite difference calculations to quantify the source effects. We use energy conservation to determine an upper bound on Rg to Lg scattering. Results indicate that Rg to Lg scattering may be important at frequencies less than 1 Hz, and in Lg coda, but is less than Lg generated directly by the explosion at higher frequencies. We use 2D and 3D finite difference calculations, using the known topography and velocity structure at Degelen Mt. and lateral heterogeneities within the crust, to estimate the effect of

  2. Cosmological explosions from cold dark matter perturbations

    NASA Technical Reports Server (NTRS)

    Scherrer, Robert J.

    1992-01-01

    The cosmological-explosion model is examined for a universe dominated by cold dark matter in which explosion seeds are produced from the growth of initial density perturbations of a given form. Fragmentation of the exploding shells is dominated by the dark-matter potential wells rather than the self-gravity of the shells, and particular conditions are required for the explosions to bootstrap up to very large scales. The final distribution of dark matter is strongly correlated with the baryons on small scales, but uncorrelated on large scales.

  3. Explosive Detection and Identification by PGNAA

    SciTech Connect

    E.H. Seabury; A.J. Caffrey

    2004-11-01

    The goal of this project was to determine the feasibility of using field-portable prompt gamma-ray neutron activation analysis (PGNAA) to detect and identify explosives in improvised nuclear devices (INDs). The studies were carried out using the Monte Carlo N-Particle (MCNP) code developed at Los Alamos National Laboratory. The model results were tested experimentally using explosive simulants and the PINS PGNAA system developed at Idaho National Engineering and Environmental Laboratory (INEEL). The results of the MCNP calculations and PINS measurements are presented in this report. The calculations and measurements were in good agreement and indicate that most explosives are readily distinguishable from one another.

  4. Thermodynamic Model of Afterburning in Explosions

    SciTech Connect

    Kuhl, A L; Howard, M; Fried, L

    2003-04-23

    Thermodynamic states encountered during afterburning of explosion products gases in air were analyzed with the Cheetah code. Results are displayed in the form of Le Chatelier diagrams: the locus of states of specific internal energy versus temperature, for six different condensed explosives charges. Accuracy of the results was confirmed by comparing the fuel and products curves with the heats of detonation and combustion, and species composition as measured in bomb calorimeter experiments. Results were fit with analytic functions u = f ( T ) suitable for specifying the thermodynamic properties required for gas-dynamic models of afterburning in explosions.

  5. Explosive propulsion applications. [to future unmanned missions

    NASA Technical Reports Server (NTRS)

    Nakamura, Y.; Varsi, G.; Back, L. H.

    1974-01-01

    The feasibility and application of an explosive propulsion concept capable of supporting future unmanned missions in the post-1980 era were examined and recommendations made for advanced technology development tasks. The Venus large lander mission was selected as the first in which the explosive propulsion concept can find application. A conceptual design was generated and its performance, weight, costs, and interaction effects determined. Comparisons were made with conventional propulsion alternatives. The feasibility of the explosive propulsion system was verified for planetology experiments within the dense atmosphere of Venus as well as the outer planets. Additionally, it was determined that the Venus large lander mission could be augmented ballistically with a significant delivery margin.

  6. Eigenvalue Detonation of Combined Effects Aluminized Explosives

    NASA Astrophysics Data System (ADS)

    Capellos, C.; Baker, E. L.; Nicolich, S.; Balas, W.; Pincay, J.; Stiel, L. I.

    2007-12-01

    Theory and performance for recently developed combined—effects aluminized explosives are presented. Our recently developed combined-effects aluminized explosives (PAX-29C, PAX-30, PAX-42) are capable of achieving excellent metal pushing, as well as high blast energies. Metal pushing capability refers to the early volume expansion work produced during the first few volume expansions associated with cylinder and wall velocities and Gurney energies. Eigenvalue detonation explains the observed detonation states achieved by these combined effects explosives. Cylinder expansion data and thermochemical calculations (JAGUAR and CHEETAH) verify the eigenvalue detonation behavior.

  7. Influence of explosive density on mechanical properties of high manganese steel explosion hardened

    NASA Astrophysics Data System (ADS)

    Hu, Xiaoyan; Shen, Zhaowu; Liu, Yingbin; Liu, Tiansheng; Wang, Fengying

    2013-12-01

    The explosion hardening tests of high manganese steel were carried out by using two kinds of explosives of the same composition but different density, respectively. The detonation velocities were tested and the relevant mechanical properties were studied. The results show that the stronger single impulse acting on the specimen, the more hardness of surface increases and the more impact toughness decreases. Compared with the explosive of 1.48 g/cm3 density, the hardness, elongation rate, and impact toughness of the sample for triple explosion with explosive of 1.38 g/cm3 density are larger at the same hardening depth. In addition, the tensile strength of the sample for triple explosion with density of 1.38 g/cm3 is higher from the surface to 15 mm below the surface hardened.

  8. Rotationally resolved infrared spectra of the explosive bouquet compounds associated with C-4 explosives

    NASA Astrophysics Data System (ADS)

    Clasp, Trocia N.; Johnson, Tiffani; Sullivan, Michael N.; Reeve, Scott W.

    2011-05-01

    The explosive material known as Composition C4, or simply C4, is an RDX based military grade explosive. RDX itself possesses a negligible vapor pressure at room temperature suggesting it is not a good target for conventional instruments designed to detect vapor phase chemical compounds. Recent research with canines has indicated that a better approach for detecting explosive vapors such as C4 is to focus on a characteristic mixture of impurities associated with the material. These characteristic mixtures of impurity vapors are referred to by canine researchers as the explosive bouquet and are fairly unique to the specific energetic material. In this paper, we will examine and report rotationally resolved infrared spectral signatures for the known compounds comprising the explosive bouquet for C4 based explosives including isobutylene, 2-ethyl-1-hexanol and cyclohexanone.

  9. Chemical-decomposition models for the thermal explosion of confined HMX, TATB, RDX, and TNT explosives

    SciTech Connect

    McGuire, R.R.; Tarver, C.M.

    1981-03-26

    Chemical decomposition models have been deduced from the available chemical kinetic data on the thermal decomposition of HMX, TATB, RDX, and TNT. A thermal conduction model is used in which the thermal conductivity of the reacting explosive decreases linearly with the mass fraction reacted to that of the gaseous products. These reactive heat flow models are used to predict the time to explosion versus reciprocal temperature curves from several heavily confined explosive tests. Good agreement is obtained between experimental and calculated explosion times for the pure explosives HMX, TATB, RDX, and TNT, mixtures such as RX-26-AF (HMX/TATB), Octol (HMX/TNT), and Comp B (RDX/TNT), and for PBX 9404, an HMX-based explosive containing an energetic nitrocellulose binder.

  10. Supernova neutrinos and explosive nucleosynthesis

    NASA Astrophysics Data System (ADS)

    Kajino, T.; Aoki, W.; Cheoun, M.-K.; Hayakawa, T.; Hidaka, J.; Hirai, Y.; Mathews, G. J.; Nakamura, K.; Shibagaki, S.; Suzuki, T.

    2014-05-01

    Core-collapse supernovae eject huge amount of flux of energetic neutrinos. We studied the explosive nucleosyn-thesis in supernovae and found that several isotopes 7Li, 11B, 92Nb, 138La and 180Ta as well as r-process nuclei are affected by the neutrino interactions. The abundance of these isotopes therefore depends strongly on the neutrino flavor oscillation due to the Mikheyev-Smirnov-Wolfenstein (MSW) effect. We discuss first how to determine the neutrino temperatures in order to explain the observed solar system abundances of these isotopes, combined with Galactic chemical evolution of the light nuclei and the heavy r-process elements. We then study the effects of neutrino oscillation on their abundances, and propose a novel method to determine the still unknown neutrino oscillation parameters, mass hierarchy and θ13, simultaneously. There is recent evidence that SiC X grains from the Murchison meteorite may contain supernova-produced light elements 11B and 7Li encapsulated in the presolar grains. Combining the recent experimental constraints on θ13, we show that our method sug-gests at a marginal preference for an inverted neutrino mass hierarchy. Finally, we discuss supernova relic neutrinos that may indicate the softness of the equation of state (EoS) of nuclear matter as well as adiabatic conditions of the neutrino oscillation.

  11. Transforming explosive art into science

    SciTech Connect

    Heller, A.

    1997-06-01

    Livermore researchers have studied and synthesized high explosives for decades because they are an integral element of every nuclear weapon. Today their work encompasses a wide range of basic research and programmatic activities. Researchers are combining breakthrough computer simulation codes, state-of-the-art experimental diagnostics, and a culture in which theoretical, synthesis, and experimental chemists and physicists work alongside each other. At the same time, they are working more closely with their partners in the energetic-materials community. Lawrence Livermore chemists are synthesizing new compounds that yield more energy, are safer to store and handle, and are less expensive and more environmentally friendly to produce. They also are designing new paths to synthesizing existing energetic molecules that are cheaper and easier on the environment. In a parallel effort, experiments are being done to better understand the fundamental physics and chemistry of energetic materials, particularly with regard to their stability, sensitivity, and performance. Livermore chemists are also working to improve efficiencies in the production of these materials.

  12. Explosive and pyrotechnic aging demonstration

    NASA Technical Reports Server (NTRS)

    Rouch, L. L., Jr.; Maycock, J. N.

    1976-01-01

    The survivability was experimentally verified of fine selected explosive and pyrotechnic propellant materials when subjected to sterilization, and prolonged exposure to space environments. This verification included thermal characterization, sterilization heat cycling, sublimation measurements, isothermal decomposition measurements, and accelerated aging at a preselected elevated temperature. Temperatures chosen for sublimation and isothermal decomposition measurements were those in which the decomposition processess occurring would be the same as those taking place in real-time aging. The elevated temperature selected (84 C) for accelerated aging was based upon the parameters calculated from the kinetic data obtained in the isothermal measurement tests and was such that one month of accelerated aging in the laboratory approximated one year of real-time aging at 66 C. Results indicate that HNS-IIA, pure PbN6, KDNBF, and Zr/KC10 are capable of withstanding sterilization. The accelerated aging tests indicated that unsterilized HNS-IIA and Zr/KC104 can withstand the 10 year, elevated temperature exposure, pure PbN6 and KDNBF exhibit small weight losses (less than 2 percent) and B/KC104 exhibits significant changes in its thermal characteristics. Accelerated aging tests after sterilization indicated that only HNS-IIA exhibited high stability.

  13. Supernova neutrinos and explosive nucleosynthesis

    SciTech Connect

    Kajino, T.; Aoki, W.; Cheoun, M.-K.; Hayakawa, T.; Hidaka, J.; Hirai, Y.; Shibagaki, S.; Mathews, G. J.; Nakamura, K.; Suzuki, T.

    2014-05-09

    Core-collapse supernovae eject huge amount of flux of energetic neutrinos. We studied the explosive nucleosyn-thesis in supernovae and found that several isotopes {sup 7}Li, {sup 11}B, {sup 92}Nb, {sup 138}La and {sup 180}Ta as well as r-process nuclei are affected by the neutrino interactions. The abundance of these isotopes therefore depends strongly on the neutrino flavor oscillation due to the Mikheyev-Smirnov-Wolfenstein (MSW) effect. We discuss first how to determine the neutrino temperatures in order to explain the observed solar system abundances of these isotopes, combined with Galactic chemical evolution of the light nuclei and the heavy r-process elements. We then study the effects of neutrino oscillation on their abundances, and propose a novel method to determine the still unknown neutrino oscillation parameters, mass hierarchy and θ{sub 13}, simultaneously. There is recent evidence that SiC X grains from the Murchison meteorite may contain supernova-produced light elements {sup 11}B and {sup 7}Li encapsulated in the presolar grains. Combining the recent experimental constraints on θ{sub 13}, we show that our method sug-gests at a marginal preference for an inverted neutrino mass hierarchy. Finally, we discuss supernova relic neutrinos that may indicate the softness of the equation of state (EoS) of nuclear matter as well as adiabatic conditions of the neutrino oscillation.

  14. Supernova explosions in the Universe.

    PubMed

    Burrows, A

    2000-02-17

    During the lifetime of our Milky Way galaxy, there have been something like 100 million supernova explosions, which have enriched the Galaxy with the oxygen we breathe, the iron in our cars, the calcium in our bones and the silicon in the rocks beneath our feet. These exploding stars also influence the birth of new stars and are the source of the energetic cosmic rays that irradiate us on the Earth. The prodigious amount of energy (approximately 10(51), or approximately 2.5 x 10(28) megatonnes of TNT equivalent) and momentum associated with each supernova may even have helped to shape galaxies as they formed in the early Universe. Supernovae are now being used to measure the geometry of the Universe, and have recently been implicated in the decades-old mystery of the origin of the gamma-ray bursts. Together with major conceptual advances in our theoretical understanding of supernovae, these developments have made supernovae the centre of attention in astrophysics. PMID:10693794

  15. Suppressing explosive synchronization by contrarians

    NASA Astrophysics Data System (ADS)

    Zhang, Xiyun; Guan, Shuguang; Zou, Yong; Chen, Xiaosong; Liu, Zonghua

    2016-01-01

    Explosive synchronization (ES) has recently received increasing attention and studies have mainly focused on the conditions of its onset so far. However, its inverse problem, i.e. the suppression of ES, has not been systematically studied so far. As ES is usually considered to be harmful in certain circumstances such as the cascading failure of power grids and epileptic seizure, etc., its suppression is definitely important and deserves to be studied. We here study this inverse problem by presenting an efficient approach to suppress ES from a first-order to second-order transition, without changing the intrinsic network structure. We find that ES can be suppressed by only changing a small fraction of oscillators into contrarians with negative couplings and the critical fraction for the transition from the first order to the second order increases with both the network size and the average degree. A brief theory is presented to explain the underlying mechanism. This finding underlines the importance of our method to improve the understanding of neural interactions underlying cognitive processes.

  16. Explosion protection methods for the power generation industry. Evaluating the hazard and reviewing explosion protection methods

    SciTech Connect

    Nixon, C.I.

    1998-07-01

    Handling carbonaceous fuels such as coal presents explosion hazards to the Power Generation Industry. This paper discusses the nature of explosions. It also provides a basis for hazard evaluation and discusses the various methods available for explosion protection. These methods include deflagration relief venting, deflagration suppression, deflagration isolation, containment and inerting. Process equipment protected by these methods include mills, cyclones, silos, hoppers and dust collectors.

  17. Explosive bonding of metal-matrix composites

    NASA Technical Reports Server (NTRS)

    Reece, O. Y.

    1969-01-01

    Explosive bonding process produces sheet composites of aluminum alloy reinforced by high-strength stainless steel wires. The bonds are excellent metallurgically, no external heat is required, various metals can be bonded, and the process is inexpensive.

  18. EXPLOSIVE MEANS TO SEPARATE CASING MEMBERS

    DOEpatents

    Botsford, N.B.

    1962-05-01

    This patent relates to a case having separable sections with intermediate interfitting tongue and groove portions. An explosive or gas generator between the tongue and groove forces them apart, when actuated, and serves to separate the case sections. (AEC)

  19. Explosive stimulation of a geothermal well: GEOFRAC

    SciTech Connect

    Mumma, D.M. )

    1982-07-01

    This paper describes the first known explosive stimulation successfully conducted in a geothermal well. Two tests were performed in a 2690-meter-(8826-ft.) deep Union Oil well at the Geysers field in Northern California in December 1981. The heat-resistant process, called GEOFRAC, uses a new unique, explosive HITEX 2, which is a nondetonable solid at room temperature. Upon melting at a temperature of 177[degrees]C (350[degrees]F), the HITEX 2 liquid becomes an explosive that can be safely heated to temperatures greater than 260[degrees]C (500[degrees]F). These unique properties of the explosive were exploited in the GEOFRAC process through the cooperative efforts of Physics International Company (PI), Rocket Research Company (RRC), Union oil Company (UO), and the university of California Los Alamos National Laboratories (LANL).

  20. Explosives detection by nuclear quadrupole resonance (NQR)

    NASA Astrophysics Data System (ADS)

    Garroway, Allen N.; Buess, Michael L.; Yesinowski, James P.; Miller, Joel B.; Krauss, Ronald A.

    1994-10-01

    Pure nuclear quadrupole resonance (NQR) of 14N nuclei is quite promising as a method for detecting explosives such as RDX and contraband narcotics such as cocaine and heroin in quantities of interest. Pure NQR is conducted without an external applied magnetic field, so potential concerns about damage to magnetically encoded data or exposure of personnel to large magnetic fields are not relevant. Because NQR frequencies of different compounds are quite distinct, we do not encounter false alarms from the NQR signals of other benign materials. We have constructed a laboratory prototype NQR explosives detector which interrogates a volume of 300 liters (10 ft3). This paper presents abbreviated results from a demonstration of the laboratory prototype NQR explosives detector conducted at the Federal Aviation Administration Technical Center in May 1994 on RDX-based explosives.

  1. Isolator fragmentation and explosive initiation tests

    SciTech Connect

    Dickson, Peter; Rae, Philip John; Foley, Timothy J.; Novak, Alan M.; Armstrong, Christopher Lee; Baca, Eva V.; Gunderson, Jake Alfred

    2015-09-30

    Three tests were conducted to evaluate the effects of firing an isolator in proximity to a barrier or explosive charge. The tests with explosive were conducted without barrier, on the basis that since any barrier will reduce the shock transmitted to the explosive, bare explosive represents the worst-case from an inadvertent initiation perspective. No reaction was observed. The shock caused by the impact of a representative plastic material on both bare and cased PBX9501 is calculated in the worst-case, 1-D limit, and the known shock response of the HE is used to estimate minimum run-to-detonation lengths. The estimates demonstrate that even 1-D impacts would not be of concern and that, accordingly, the divergent shocks due to isolator fragment impact are of no concern as initiating stimuli.

  2. High explosives skid impact initiation study

    SciTech Connect

    Vigil, A.S.; Bunch, J.M.; Jaeger, D.L.; Smith, P.D.; Abeyta, E.E.

    1990-06-01

    The objective of this study was to develop a better quantitative understanding of explosive behavior under skid impact conditions. We evaluated the effects of sample weight, impact velocity, contact surface area at impact, target surface roughness, and target material on the skid impact HE ignition threshold. We also quantified the effects of two parameters that had never been fully investigated in the standard skid impact sensitivity test: explosive sample size and angle of incidence. These parameters were studied experimentally by conducting a series of tests, and analytical, with a number of one-, two-, and three-dimensional computer models. This study is the first phase in a program to measure the transient heat produced in the ignition of a high explosive sample as it impacts an infrared (IR) transmissive target. We will use the experimentally derived data to enhance our ability to predict the onset of ignition in impact-heated high explosives. 12 refs., 9 figs., 2 tabs.

  3. Unreacted Hugoniots for porous and liquid explosives

    SciTech Connect

    Gustavsen, R.L.; Sheffield, S.A.

    1993-08-01

    Numerous authors have measured the Hugoniots of a variety of granular explosives pressed to different densities. Each explosive at each density was typically then treated as a unique material having its own Hugoniot. By combining methods used by Hayes, Sheffield and Mitchell (for describing the Hugoniot of HNS at various densities) with Hermann`s P-{alpha} model, it is only necessary to know some thermodynamic constants or the Hugoniot of the initially solid material and the porous material sound speed to obtain accurate unreacted Hugoniots for the porous explosive. We discuss application of this method to several materials including HMX, PETN, TNT, and Tetryl, as well as HNS. We also show that the ``Universal Liquid Hugoniot`` can be used to calculate the unreacted Hugoniot for liquid explosives. With this method only the ambient pressure sound speed and density are needed to predict the Hugoniot. Applications presented include nitromethane and liquid TNT.

  4. 49 CFR 173.54 - Forbidden explosives.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ..., including a salt of a weak base and a strong acid. (c) A leaking or damaged package or article containing an... loaded firearm (except as provided in 49 CFR 1544.219). (g) Fireworks that combine an explosive and...

  5. Detonation Properties Measurements for Inorganic Explosives

    NASA Astrophysics Data System (ADS)

    Morgan, Brent A.; Lopez, Angel

    2005-03-01

    Many commonly available explosive materials have never been quantitatively or theoretically characterized in a manner suitable for use in analytical models. This includes inorganic explosive materials used in spacecraft ordnance, such as zirconium potassium perchlorate (ZPP). Lack of empirical information about these materials impedes the development of computational techniques. We have applied high fidelity measurement techniques to experimentally determine the pressure and velocity characteristics of ZPP, a previously uncharacterized explosive material. Advances in measurement technology now permit the use of very small quantities of material, thus yielding a significant reduction in the cost of conducting these experiments. An empirical determination of the explosive behavior of ZPP derived a Hugoniot for ZPP with an approximate particle velocity (uo) of 1.0 km/s. This result compares favorably with the numerical calculations from the CHEETAH thermochemical code, which predicts uo of approximately 1.2 km/s under ideal conditions.

  6. Explosives Detection and Identification by PGNAA

    SciTech Connect

    E. H. Seabury; A. J. Caffrey

    2006-04-01

    The feasibility of using field-portable prompt gamma-ray neutron activation analysis (PGNAA) to detect and identify explosives in improvised nuclear devices has been studied computationally, using the Monte Carlo N-Particle (MCNP) code developed at Los Alamos National Laboratory. The Monte Carlo results, in turn were tested experimentally using explosive simulants and the PINS PGNAA system developed at Idaho National Laboratory (INL). The results of the MCNP calculations and PINS measurements have been previously reported. In this report we describe measurements performed on actual explosives and compare the results with calculations. The calculations and measurements were in good agreement and indicate that most explosives are readily distinguishable from one another by PGNAA

  7. Corona-discharge-initiated mine explosions

    SciTech Connect

    Sacks, H.K.; Novak, T.

    2005-10-01

    Strong circumstantial evidence suggests that lightning has initiated methane explosions in abandoned and sealed areas of underground coal mines. The Mine Safety and Health Administration (MSHA) investigated several of these occurrences within recent years. The investigated explosions occurred at significant depths, ranging from 700 to 1200 ft. Data from the National Lightning Detection Network indicated a strong correlation between the times and locations of the explosions with those of specific lightning strikes. This paper proposes that corona discharge from a steel borehole casing is the most likely mechanism responsible for these ignitions. A recently investigated mine explosion and fire at a depth greater than 1000 ft was selected for this study. Computer simulations were performed, using data collected at the mine site. CDEGS software from Safe Engineering Services & Technologies, Ltd. and MaxwellSV from Ansoft Corporation were used for the simulations.

  8. ORNL Radioactive Beams for Stellar Explosion Studies

    NASA Astrophysics Data System (ADS)

    Smith, Michael S.

    2008-05-01

    Thermonuclear reactions on unstable nuclei generate the energy that power nova explosions and X-ray bursts. In these explosions and others such as supernovae, these reactions serve to synthesize nuclei that (via their decay) can serve as tracers of the explosion mechanism. A powerful approach to improve our understanding of these explosions is to utilize beams of radioactive nuclei for direct and indirect measurements of these reactions. We are pursuing this approach at the Holifield Radioactive Ion Beam Facility (HRIBF) at Oak Ridge National Laboratory (ORNL) to study reactions in the rp-process (with beams of 17,18F) and the r-process (with beams of 82Ge, 84Se 130,132Sn, 134Te). These measurements are combined with synergistic data evaluations and element synthesis calculations. Highlights of recent results are presented.

  9. Differential Spectroscopic Imaging of Particulate Explosives Residue

    SciTech Connect

    Bernacki, Bruce E.; Ho, Nicolas

    2008-04-01

    We present experimental results showing transmission and reflection imaging of approximately 100 microgram quantities of particulate explosives residue using a commercial uncooled microbolometer infrared camera and CO2 laser differential wavelength illumination.

  10. Traumatic corneal endothelial rings from homemade explosives.

    PubMed

    Ng, Soo Khai; Rudkin, Adam K; Galanopoulos, Anna

    2013-08-01

    Traumatic corneal endothelial rings are remarkably rare ocular findings that may result from blast injury. We present a unique case of bilateral traumatic corneal endothelial rings secondary to blast injury from homemade explosives. PMID:23474743

  11. 30 CFR 77.1302 - Vehicles used to transport explosives.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Vehicles used to transport explosives. 77.1302... COAL MINES Explosives and Blasting § 77.1302 Vehicles used to transport explosives. (a) Vehicles used to transport explosives, other than blasting agents, shall have substantially constructed bodies,...

  12. 30 CFR 56.6903 - Burning explosive material.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Burning explosive material. 56.6903 Section 56... MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Explosives General Requirements § 56.6903 Burning explosive material. If explosive material is suspected of burning at the...

  13. 30 CFR 57.6903 - Burning explosive material.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Burning explosive material. 57.6903 Section 57... MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Explosives General Requirements-Surface and Underground § 57.6903 Burning explosive material. If explosive...

  14. 27 CFR 70.445 - Commerce in explosives.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... Relating to Alcohol, Tobacco, Firearms, and Explosives Provisions Relating to Firearms, Shells and Cartridges, and Explosives § 70.445 Commerce in explosives. Part 555 of title 27 CFR contains the regulations... 27 Alcohol, Tobacco Products and Firearms 2 2012-04-01 2011-04-01 true Commerce in explosives....

  15. 30 CFR 56.6305 - Unused explosive material.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Unused explosive material. 56.6305 Section 56... MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Explosives Use § 56.6305 Unused explosive material. Unused explosive material shall be moved to a protected location...

  16. 30 CFR 57.6130 - Explosive material storage facilities.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Explosive material storage facilities. 57.6130... NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Explosives Storage-Surface Only § 57.6130 Explosive material storage facilities. (a) Detonators and explosives...

  17. 30 CFR 56.6130 - Explosive material storage facilities.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Explosive material storage facilities. 56.6130... NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Explosives Storage § 56.6130 Explosive material storage facilities. (a) Detonators and explosives shall be stored...

  18. 30 CFR 56.6905 - Protection of explosive material.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Protection of explosive material. 56.6905... NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Explosives General Requirements § 56.6905 Protection of explosive material. (a) Explosive material shall be...

  19. 33 CFR 401.68 - Explosives Permission Letter.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 33 Navigation and Navigable Waters 3 2012-07-01 2012-07-01 false Explosives Permission Letter. 401..., DEPARTMENT OF TRANSPORTATION SEAWAY REGULATIONS AND RULES Regulations Dangerous Cargo § 401.68 Explosives Permission Letter. (a) A Seaway Explosives Permission Letter is required for an explosive vessel in...

  20. 30 CFR 77.1300 - Explosives and blasting.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Explosives and blasting. 77.1300 Section 77... Explosives and Blasting § 77.1300 Explosives and blasting. (a) No explosives, blasting agent, detonator, or... accordance with the provisions of §§ 77.1301 through 77.1304, inclusive. (b) The term “explosives” as used...