Ore Deposits of the Jerome and Bradshaw Mountains Quadrangles, Arizona

USGS Publications Warehouse

Lindgren, Waldemar; Heikes, V.C.

1926-01-01

In the summer of 1922, at the request of the Director of the United States Geological Survey, I undertook an examination of the ore deposits in the Jerome and Bradshaw Mountains quadrangles, Ariz. (See fig. 1.) The object of this work was not a detailed investigation of each deposit but rather a coordination and classification of the occurrences and an attempt to ascertain their origin and economic importance. Almost all the deposits occur in pre-Cambrian rocks or in rocks that are not readily differentiated from the pre-Cambrian. In the northern part of the Jerome quadrangle there are large areas of almost horizontal Paleozoic beds, and in both quadrangles there are also large areas of lava flows of Tertiary age. Finally there are wide spaces occupied by Tertiary tuff and limestone, or by Tertiary and Quaternary wash filling the valleys between the mountain ranges. But all these rocks except the pre-Cambrian are practically barren of ore deposits, and the problem therefore narrowed itself to an examination of the pre-Cambrian areas. This task was greatly facilitated by the careful work of Jaggar and Palache, set forth in the Bradshaw Mountains folio,l in which the southern quadrangle of the two under present consideration is mapped geologically and described, and which also includes a comprehensive though brief discussion of the mineral deposits. There is no published geologic map of the Jerome quadrangle, but I had the opportunity through the courtesy of Dr. G. M. Butler, Director of the Arizona Bureau of Mines, to use a manuscript map of this area prepared for the State by Mr. L. E. Reber, jr., and Mr. Olaf Jenkins.

Ore microscopy of the Paoli silver-copper deposit, Oklahoma

USGS Publications Warehouse

Thomas, C.A.; Hagni, R.D.; Berendsen, P.

1991-01-01

The Paoli silver-copper deposit is located in south-central Oklahoma, 56 km south-southeast from Norman, Oklahoma. It was mined for high-grade silver-copper near the beginning of this century, and intensive exploratory drilling during the early 1970's delineated unmined portions of the deposit. A collaborative study between the U.S.G.S., the Kansas Geological Survey, and the University of Missouri-Rolla was undertaken to provide new information on the character of red bed copper deposits of the Midcontinent region. The Paoli deposit has been interpreted to occur as a roll-front type of deposit. The silver and copper mineralization occurs within paleochannels in the Permian Wellington Formation. The silver-copper interfaces appear to be controlled by oxidation-reduction interfaces that are marked by grey to red color changes in the host sandstone. Ore microscopic examinations of polished thin sections show that unoxidized ore consists of chalcocite, digenite, chalcopyrite, covellite and pyrite; and oxidized ores are characterized by covellite, bornite, hematite and goethite. In sandstone-hosted ores, chalcocite and digenite replace dolomite and border clastic quartz grains. In siltstone-hosted ores, the copper sulfide grains have varied shapes; most are irregular in shape and 5-25 ??m across, others have euhedral shapes suggestive of pyrite crystal replacements, and some are crudely spherical and are 120-200 ??m across. Chalcopyrite is the predominant copper sulfide at depth. Covellite and malachite replace chalcocite and digenite near the surface. Silver only occurs as native silver; most as irregularly shaped grains 40-80 ??m across, but some as cruciform crystals that are up to 3.5 mm across. The native silver has been deposited after copper sulfides, and locally replaces chalcocite. Surficial nodules of pyrite, malachite and hematite locally are present in outcrops at the oxidation-reduction fronts. Polished sections of the nodules show that malachite forms a

The Gas Hills uranium district and some probable controls for ore deposition

USGS Publications Warehouse

Zeller, Howard Davis

1957-01-01

Uranium deposits occur in the upper coarse-grained facies of the Wind River formation of Eocene age in the Gas Hills district of the southern part of the Wind River Basin. Some of the principal deposits lie below the water table in the unoxidized zone and consist of uraninite and coffinite occurring as interstitial fillings in irregular blanket-like bodies. In the near-surface deposits that lie above the water table, the common yellow uranium minerals consist of uranium phosphates, silicates, and hydrous oxides. The black unoxidized uraninite -coffinite ores show enrichment of molybdenum, arsenic, and selenium when compared to the barren sandstone. Probable geologic controls for ore deposits include: 1) permeable sediments that allowed passage of ore-bearing solutions; 2) numerous faults that acted as impermeable barriers impounding the ore -bearing solutions; 3) locally abundant pyrite, carbonaceous material, and natuial gas containing hydrogen sulfide that might provide a favorable environment for precipitation of uranium. Field and laboratory evidence indicate that the uranium deposits in the Gas Hills district are very young and related to the post-Miocene to Pleistocene regional tilting to the south associated with the collapse of the Granite Mountains fault block. This may have stopped or reversed ground water movement from a northward (basinward) direction and alkaline ground water rich in carbonate could have carried the uranium into the favorable environment that induced precipitation.

Mixing from below in hydrothermal ore deposits

NASA Astrophysics Data System (ADS)

Bons, Paul D.; Gomez-Rivas, Enrique; Markl, Gregor; Walter, Bejamin

2014-05-01

Unconformity-related hydrothermal ore deposits typically show indications of mixing of two end-member fluids: (a) hot, deep, rock-buffered basement brines and (b) colder fluids derived from the surface or overlying sediments. The hydromechanics of bringing these fluids together from above and below remain unclear. Classical percolative Darcy-flow models are inconsistent with (1) fluid overpressure indicated by fracturing and brecciation, (2) fast fluid flow indicated by thermal disequilibrium, and (3) strong fluid composition variations on the mm-scale, indicated by fluid inclusion analyses (Bons et al. 2012; Fusswinkel et al. 2013). We propose that fluids first descend, sucked down by desiccation reactions in exhumed basement. Oldest fluids reach greatest depths, where long residence times and elevated temperatures allow them the extensively equilibrate with their host rock, reach high salinity and scavenge metals, if present. Youngest fluids can only penetrate to shallower depths and can (partially) retain signatures from their origin, for example high Cl/Br ratios from the dissolution of evaporitic halite horizons. When fluids are released from all levels of the crustal column, these fluids mix during rapid ascent to form hydrothermal ore deposits. Mixing from below provides a viable hydromechanical mechanism to explain the common phenomenon of mixed shallow and deep fluids in hydrothermal ore deposits. Bons, P.D., Elburg, M.A., Gomez-Rivas, E. 2012. A review of the formation of tectonic veins and their microstructures. J. Struct. Geol. doi:10.1016/j.jsg.2012.07.005 Fusswinkel, T., Wagner, T., Wälle, M., Wenzel, T., Heinrich, C.A., Markl, M. 2013. Fluid mixing forms basement-hosted Pb-Zn deposits: Insight from metal and halogen geochemistry of individual fluid inclusions. Geology. doi:10.1130/G34092.1

Application of natural analog studies to exploration for ore deposits

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gustafson, D.L.

1995-09-01

Natural analogs are viewed as similarities in nature and are routinely utilized by exploration geologists in their search for economic mineral deposits. Ore deposit modeling is undertaken by geologists to direct their exploration activities toward favorable geologic environments and, therefore, successful programs. Two types of modeling are presented: (i) empirical model development based on the study of known ore deposit characteristics, and (ii) concept model development based on theoretical considerations and field observations that suggest a new deposit type, not known to exist in nature, may exist and justifies an exploration program. Key elements that are important in empirical modelmore » development are described, and examples of successful applications of these natural analogs to exploration are presented. A classical example of successful concept model development, the discovery of the McLaughlin gold mine in California, is presented. The utilization of natural analogs is an important facet of mineral exploration. Natural analogs guide explorationists in their search for new discoveries, increase the probability of success, and may decrease overall exploration expenditure.« less

Evolution of Ore Deposits and Technology Transfer Project: Isotope and Chemical Methods in Support of the U.S. Geological Survey Science Strategy, 2003-2008

USGS Publications Warehouse

Rye, Robert O.; Johnson, Craig A.; Landis, Gary P.; Hofstra, Albert H.; Emsbo, Poul; Stricker, Craig A.; Hunt, Andrew G.; Rusk, Brian G.

2010-01-01

Principal functions of the U.S. Geological Survey (USGS) Mineral Resources Program are providing assessments of the location, quantity, and quality of undiscovered mineral deposits, and predicting the environmental impacts of exploration and mine development. The mineral and environmental assessments of domestic deposits are used by planners and decisionmakers to improve the stewardship of public lands and public resources. Assessments of undiscovered mineral deposits on a global scale reveal the potential availability of minerals to the United States and other countries that manufacture goods imported to the United States. These resources are of fundamental relevance to national and international economic and security policy in our globalized world economy. Performing mineral and environmental assessments requires that predictions be made of the likelihood of undiscovered deposits. The predictions are based on geologic and geoenvironmental models that are constructed for the diverse types of mineral deposits from detailed descriptions of actual deposits and detailed understanding of the processes that formed them. Over the past three decades the understanding of ore-forming processes has benefited greatly from the integration of laboratory-based geochemical tools with field observations and other data sources. Under the aegis of the Evolution of Ore Deposits and Technology Transfer Project (referred to hereinafter as the Project), a 5-year effort that terminated in 2008, the Mineral Resources Program provided state-of-the-art analytical capabilities to support applications of several related geochemical tools to ore-deposit-related studies. The analytical capabilities and scientific approaches developed within the Project have wide applicability within Earth-system science. For this reason the Project Laboratories represent a valuable catalyst for interdisciplinary collaborations of the type that should be formed in the coming years for the United States to meet

Use of structural geology in exploration for and mining of sedimentary rock-hosted Au deposits

USGS Publications Warehouse

Peters, Stephen G.

2001-01-01

Structural geology is an important component in regional-, district- and orebody-scale exploration and development of sedimentary rock-hosted Au deposits.Identification of timing of important structural events in an ore district allows analysis and classification of fluid conduits and construction of genetic models for ore formation.The most practical uses of structural geology deal with measurement and definition of various elements that comprise orebodies, which can then be directly applied to ore-reserve estimation,ground control,grade control, safety issues,and mine planning.District- and regional-scale structural studies are directly applicable to long-term strategic planning,economic analysis,and land ownership. Orebodies in sedimentary rock-hosted Au deposits are discrete, hypogene, epigenetic masses usually hosted in a fault zone,breccia mass, or lithologic bed or unit. These attributes allow structural geology to be directly applied to the mining and exploration of sedimentary rock-hosted Au deposits. Internal constituents in orebodies reflect unique episodes relating to ore formation.The main internal constituents in orebodies are ore minerals, gangue, and alteration minerals that usually are mixed with one another in complex patterns, the relations among which may be used to interpret the processes of orebody formation and control.Controls of orebody location and shape usually are due to structural dilatant zones caused by changes in attitude, splays, lithologic contacts,and intersections of the host conduit or unit.In addition,conceptual parameters such as district fabric,predictable distances, and stacking also are used to understand the geometry of orebodies.Controls in ore districts and location and geometry of orebodies in ore districts can be predicted to various degrees by using a number of qualitative concepts such as internal and external orebody plunges,district plunge, district stacking, conduit classification, geochemical, geobarometric and

Mineralogical and geochemical characteristics of the Noamundi-Koira basin iron ore deposits (India)

NASA Astrophysics Data System (ADS)

Mirza, Azimuddin; Alvi, Shabbar Habib; Ilbeyli, Nurdane

2015-04-01

India is one of the richest sources of iron ore deposits in the world; and one of them is located in the Noamundi-Koira basin, Singhbhum-Orissa craton. The geological comparative studies of banded iron formation (BIF) and associated iron ores of Noamundi-Koira iron ore deposits, belonging to the iron ore group in eastern India, focus on the study of mineralogy and major elemental compositions along with the geological evaluation of different iron ores. The basement of the Singhbhum-Orissa craton is metasedimentary rocks which can be traced in a broadly elliptical pattern of granitoids, surrounded by metasediments and metavolcanics of Greenstone Belt association. The Singhbhum granitoid is intrusive into these old rocks and to younger, mid Archaean metasediments, including iron formations, schists and metaquartzites and siliciclastics of the Precambrian Iron Ore Group (Saha et al., 1994; Sharma, 1994). The iron ore of Noamundi-Koira can be divided into seven categories (Van Schalkwyk and Beukes 1986). They are massive, hard laminated, soft laminated, martite-goethite, powdery blue dust and lateritic ore. Although it is more or less accepted that the parent rock of iron ore is banded hematite jasper (BHJ), the presence of disseminated martite in BHJ suggests that the magnetite of protore was converted to martite. In the study area, possible genesis of high-grade hematite ore could have occurred in two steps. In the first stage, shallow, meteoric fluids affect primary, unaltered BIF by simultaneously oxidizing magnetite to martite and replacing quartz with hydrous iron oxides. In the second stage of supergene processes, deep burial upgrades the hydrous iron oxides to microplaty hematite. Removal of silica from BIF and successive precipitation of iron resulted in the formation of martite- goethite ore. Soft laminated ores were formed where precipitation of iron was partial or absent. The leached out space remains with time and the interstitial space is generally filled

Ores and Climate Change - Primary Shareholders

NASA Astrophysics Data System (ADS)

Stein, Holly J.; Hannah, Judith L.

2015-04-01

Many in the economic geology community concern themselves with details of ore formation at the deposit scale, whether tallying fluid inclusion data to get at changes in ore-forming fluids or defining structures that aid and abet mineralization. These compilations are generally aimed at interpretation of events at the site of ore formation, with the goal being assignment of the deposit to a sanctioned ore deposit model. While providing useful data, this approach is incomplete and does not, by itself, serve present-day requirements for true interdisciplinary science. The ore-forming environment is one of chaos and disequilibrium at nearly all scales (Stein, 2014). Chaos and complexity are documented by variably altered rocks, veins or disseminated mineralization with multi-generational fluid histories, erratic and unusual textures in host rocks, and the bitumen or other hydrocarbon products entwined within many ore deposits. This should give pause to our drive for more data as a means to find "the answer". The answer lies in the kind of data collected and more importantly, in the way we interpret those data. Rather than constructing an ever-increasing catalog of descriptive mutations on sanctioned ore deposit models (e.g., IOGC or Iron-Oxide Copper Gold deposits), the way forward is to link source and transport of metals, sulfur, and organic material with regional and ultimately whole Earth chemical evolution. Important experimental work provides chemical constraints in controlled and behaved environments. To these data, we add imagination and interpretation, always tying back to field observations. In this paper, several key points are made by way of ore deposit examples: (1) many IOCG deposits are outcomes of profound changes in the chemistry of the Earth's surface, in the interplay of the atmosphere, hydrosphere, biosphere, and lithosphere; (2) the redox history of Fe in deep earth may be ultimately expressed in the ore-forming sequence; and (3) the formation of

Geology, ore facies and sulfur isotopes geochemistry of the Nudeh Besshi-type volcanogenic massive sulfide deposit, southwest Sabzevar basin, Iran

NASA Astrophysics Data System (ADS)

Maghfouri, Sajjad; Rastad, Ebrahim; Mousivand, Fardin; Lin, Ye; Zaw, Khin

2016-08-01

The southwest Sabzevar basin is placed in the southwestern part of a crustal domain known as the Sabzevar zone, at the north of Central Iranian microcontinent. This basin hosts abundant mineral deposits; particularly of the Mn exhalative and Cu-Zn volcanogenic massive sulfide (VMS) types. The evolution of this basin is governed by the Neo-tethys oceanic crust subduction beneath the Central Iranian microcontinent and by the resulting continental arc (Sanandaj-Sirjan) and back-arc (Sabzevar-Naien). This evolution followed two major sequences: (I) Lower Late Cretaceous Volcano-Sedimentary Sequence (LLCVSS), which is indicated by fine-grained siliciclastic sediments, gray basic coarse-grained different pyroclastic rocks and bimodal volcanism. During this stage, tuff-hosted stratiform, exhalative Mn deposits (Nudeh, Benesbourd, Ferizy and Goft), oxide Cu deposits (Garab and Ferizy) and Cu-Zn VMS (Nudeh, Chun and Lala) deposits formed. (II) Upper Late Cretaceous Sedimentary Dominated Sequence (ULCSS), including pelagic limestone, marly tuff, silty limestone and marl with minor andesitic tuff rocks. The economically most important Mn (Zakeri and Cheshmeh-sefid) deposits of Sabzevar zone occur within the marly tuff of this sequence. The Nudeh Cu-Zn volcanogenic massive sulfide (VMS) deposit is situated in the LLCVSS. The host-rock of deposits consists of alkali olivine basalt flow and tuffaceous silty sandstone. Mineralization occurs as stratiform blanket-like and tabular orebodies. Based on ore body structure, mineralogy, and ore fabric, we recognize three different ore facies in the Nudeh deposit: (1) a stringer zone, consisting of a discordant mineralization of sulfides forming a stockwork of sulfide-bearing quartz veins cutting the footwall volcano-sedimentary rocks; (2) a massive ore, consisting of massive replacement pyrite, chalcopyrite, sphalerite and Friedrichite with magnetite; (3) bedded ore, with laminated to disseminated pyrite, and chalcopyrite

Geological controls on refractory ore in an orogenic gold deposit, Macraes mine, New Zealand

NASA Astrophysics Data System (ADS)

Petrie, B. S.; Craw, D.; Ryan, C. G.

2005-07-01

The Macraes mine is hosted in an orogenic (mesothermal) gold deposit in metasedimentary rocks of the Otago Schist belt. Much gold occurs within altered schist with minimal silica-addition, and this study focuses on altered schist ore types. The unmineralized host schists are chemically and mineralogically uniform in composition, but include two end-member rock types: feldspathic schist and micaceous schist. Both rock types have undergone hydrothermal alteration along a shallow-dipping foliation-parallel shear zone, but their different rheological properties have affected the style of mineralisation. Micaceous schist has been extensively recrystallized and hydrothermally altered during ductile deformation, to form ores characterized by abundant, disseminated millimetre-scale pyrite cubes (typically 1 2 wt% S) and minor silicification. The earliest pyrite contained Ni and/or As in solid solution and no gold was imaged in these pyrites or later arsenopyrite grains. The ore type is refractory and gold recovery by cyanide leaching is less than 50%, with lowest recovery in rocks that have been less affected by later brittle deformation. In contrast, hydrothermally altered feldspathic schist is characterized by mineralised black microshears and veinlets formed during shear-zone related brittle deformation. Microsheared ore has relatively low sulphur content (<0.7 wt%) and muscovite has been illitised during hydrothermal alteration. Pyrite and arsenopyrite in microshears are fractured and deformed, and contain 1 10 μm blebs of gold. Later pyrite veinlets also contain micron- to submicron-scale inclusions of sphalerite, chalcopyrite, galena, and gold (≤10 microns). Gold in microsheared ore is more readily recoverable than in the refractory ore, although encapsulation of the fine gold grains inhibits cyanidation. Both microsheared ore and disseminated pyritic ore pass laterally into mineralised black shears, which contain hydrothermal graphite and late-stage cataclastic

Geology of the pitchblende ores of Colorado

USGS Publications Warehouse

Bastin, Edson S.

1915-01-01

The large amount of public interest that has recently been manifested in radium because of the apparent cures of cancer effected by certain of its emanations makes it desirable to place before the public as promptly as possible all available information in regard to the occurrence of the minerals from which radium may be derived. The following account of the mode of occurrence of pitchblende at Quartz Hill, in Gilpin County, Colo., is therefore published in advance of a much larger report on the same region in which many other types of ore deposits will be considered. The field studies were made.in the fall of 1912. As the geologic relations at Quartz Hill differ in important particulars from those at foreign localities, a summary of the genetically important features of the principal European occurrences is included for purposes of comparison.

Geological and geochemical studies of the Shujiadian porphyry Cu deposit, Anhui Province, Eastern China: Implications for ore genesis

NASA Astrophysics Data System (ADS)

Wang, Shiwei; Zhou, Taofa; Yuan, Feng; Fan, Yu; White, Noel C.; Lin, Fengjie

2015-05-01

Most porphyry deposits in the world occur in magmatic arc settings and are related to subduction of oceanic plates. A small proportion of porphyry deposits occur in intracontinental settings, however they are still poorly understood. Shujiadian, a newly-discovered porphyry Cu deposit, is located in the Middle-Lower Yangtze River Valley metallogenic belt and belongs to the intracontinental class. The deposit has classic alteration zones defined by a core of potassic alteration and local Ca-silicate alteration, which is overprinted by a feldspar-destructive alteration zone and cut by veins containing epidote and chlorite. Wallrocks of the deposit are unreactive quartz-rich sedimentary rocks. Three main paragenetic stages have been recognized based on petrographic observations; silicate stage, quartz-sulfide stage, and sulfide-carbonate stage. Quartz + pyrite + chalcopyrite ± molybdenite veins, and quartz + chalcopyrite + pyrite veins of the quartz-sulfide stage contribute most of the copper, and chalcopyrite + chlorite ± pyrite ± pyrrhotite ± quartz ± illite veins of the sulfide-carbonate stage also contribute part of the copper; all the mineralized veins are associated with feldspar-destructive alteration. Investigations on the fluid inclusions in Shujiadian indicate that the ore-forming fluids had four evolutionary episodes: immiscibility and overpressure in the silicate stage, boiling in the quartz-sulfide stage and mixing with meteoric water in the sulfide-carbonate stage. Sulfur and strontium isotope studies suggest that ore metals were mainly derived from magmatic-hydrothermal fluids, and combined with our study of fluid inclusions, we infer that decompression, changes in oxygen fugacity and sulfur content were the main factors that caused Cu precipitation. Compared with porphyry deposits in magmatic arc settings, there are some differences in the ore-bearing rock, alteration, and the composition of ore-forming fluids.

Geological and geochemical aspects of uranium deposits: a selected, annotated bibliography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas, J.M.; Brock, M.L.; Garland, P.A.

1978-06-01

A compilation of 490 references is presented which is the second in a series compiled from the National Uranium Resource Evaluation (NURE) Bibliographic Data Base. This data base is one of six created by the Ecological Sciences Information Center, Oak Ridge National Laboratory, for the Grand Junction Office of the Department of Energy. Major emphasis for this volume has been placed on uranium geology, encompassing deposition, genesis of ore deposits, and ore controls; and prospecting techniques, including geochemistry and aerial reconnaissance. The following indexes are provided to aid the user in locating references of interest: author, geographic location, quadrangel name,more » geoformational feature, taxonomic name, and keyword.« less

Computer finds ore

NASA Astrophysics Data System (ADS)

Bell, Peter M.

Artificial intelligence techniques are being used for the first time to evaluate geophysical, geochemical, and geologic data and theory in order to locate ore deposits. After several years of development, an intelligent computer code has been formulated and applied to the Mount Tolman area in Washington state. In a project funded by the United States Geological Survey and the National Science Foundation a set of computer programs, under the general title Prospector, was used successfully to locate a previously unknown ore-grade porphyry molybdenum deposit in the vicinity of Mount Tolman (Science, Sept. 3, 1982).The general area of the deposit had been known to contain exposures of porphyry mineralization. Between 1964 and 1978, exploration surveys had been run by the Bear Creek Mining Company, and later exploration was done in the area by the Amax Corporation. Some of the geophysical data and geochemical and other prospecting surveys were incorporated into the programs, and mine exploration specialists contributed to a set of rules for Prospector. The rules were encoded as ‘inference networks’ to form the ‘expert system’ on which the artificial intelligence codes were based. The molybdenum ore deposit discovered by the test is large, located subsurface, and has an areal extent of more than 18 km2.

GEOLOGY, SULFUR ISOTOPES AND THE ORIGIN OF THE HEATH STEELE ORE DEPOSITS, NEWCASTLE, N.B., CANADA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dechow, E.

The Heath Steele mine is located 35 miles northwest of Newcastle, New Brunswick, Canada. Middle Ordovician Tetagouche Group rocks, consisting of siliceous and basic volcanic rocks, and fine-grained quartz sericite schists and porphyry, have been folded into a steeply plunging recumbent anticline. The ore deposits of zinc, lead, and copper are associated with minor folding and/or sheared dilatent zones at or near the contact between porphyry and fine-grained senicitic schist. Mineralogically the sulfide bodies consist of early, euhedral arsenopyrite, magnetite, and pyrite, followed by interstitial pyrrhotite, sphalerite, chalcopyrite and galena. Minor minerals are ternantite-tetrahedrite, bismuthinite, marcasite, hematite, and some graphite.more » Supergene minerals consist of chalcocite, covellite, and marcasite with a little native silver. Little hypogene replacement has taken place between the minerals, which show a "porphyritic" texture. Sulfur isotope ratios were determined for over 150 sulfide and sulfate specimens from five of the seven ore bodies, and from granite, acid and basic volcanics, porphyry, and sediments. The results indicate that there is no detectable fractionation either during hypogene mineralization or supergene enrichment. The spread (21.82 to 22.02) covered by the ratios is narrow, and suggestive of a well homogenized source of mineral solutions. The enrichment of S/sup 34/ in the ore sulfides and the presence of graphite, evident from mineralographic studies and mass spectrometric analysis, suggests reduction of original sulfates (known to be enriched in S/sup 34/) by organic carbon at temperatures in excess of 500 deg C. A calculation based on the isotopic exchange reaction between sulfide and sulfate under equilibrium conditions and the spread of the ratios indicates a temperature of 700 to 800 deg C for the source. Finally the ratios determined for sulfides in a gneissic granite close to Heath Steele have the same ratio as the ore

Geology, geochemistry, and genesis of the Greens Creek massive sulfide deposit, Admiralty Island, southeastern Alaska

USGS Publications Warehouse

Taylor, Cliff D.; Johnson, Craig A.

2010-01-01

In 1996, a memorandum of understanding was signed by representatives of the U.S. Geological Survey and Kennecott Greens Creek Mining Company to initiate a cooperative applied research project focused on the Greens Creek massive sulfide deposit in southeastern Alaska. The goals of the project were consistent with the mandate of the U.S. Geological Survey Mineral Resources Program to maintain a leading role in national mineral deposits research and with the need of Kennecott Greens Creek Mining Company to further development of the Greens Creek deposit and similar deposits in Alaska and elsewhere. The memorandum enumerated four main research priorities: (1) characterization of protoliths for the wall rocks, and elucidation of their alteration histories, (2) determination of the ore mineralogy and paragenesis, including metal residences and metal zonation within the deposit, (3) determination of the ages of events important to ore formation using both geochronology and paleontology, and (4) development of computer models that would allow the deposit and its host rocks to be examined in detail in three dimensions. The work was carried out by numerous scientists of diverse expertise over a period of several years. The written results, which are contained in this Professional Paper, are presented by 21 authors: 13 from the U.S. Geological Survey, 4 from Kennecott Greens Creek Mining Company, 2 from academia, and 2 from consultants. The Greens Creek deposit (global resource of 24.2 million tons at an average grade of 13.9 percent zinc, 5.1 percent lead, 0.15 troy ounce per ton gold, and 19.2 troy ounces per ton silver at zero cutoff) formed in latest Triassic time during a brief period of rifting of the Alexander terrane. The deposit exhibits a range of syngenetic, diagenetic, and epigenetic features that are typical of volcanogenic (VMS), sedimentary exhalative (SEDEX), and Mississippi Valley-type (MVT) genetic models. In the earliest stages of rifting, formation of

The coupled geochemistry of Au and As in pyrite from hydrothermal ore deposits

NASA Astrophysics Data System (ADS)

Deditius, Artur P.; Reich, Martin; Kesler, Stephen E.; Utsunomiya, Satoshi; Chryssoulis, Stephen L.; Walshe, John; Ewing, Rodney C.

2014-09-01

The ubiquity of Au-bearing arsenian pyrite in hydrothermal ore deposits suggests that the coupled geochemical behaviour of Au and As in this sulfide occurs under a wide range of physico-chemical conditions. Despite significant advances in the last 20 years, fundamental factors controlling Au and As ratios in pyrite from ore deposits remain poorly known. Here we explore these constraints using new and previously published EMPA, LA-ICP-MS, SIMS, and μ-PIXE analyses of As and Au in pyrite from Carlin-type Au, epithermal Au, porphyry Cu, Cu-Au, and orogenic Au deposits, volcanogenic massive sulfide (VHMS), Witwatersrand Au, iron oxide copper gold (IOCG), and coal deposits. Pyrite included in the data compilation formed under temperatures from ∼30 to ∼600 °C and in a wide variety of geological environments. The pyrite Au-As data form a wedge-shaped zone in compositional space, and the fact that most data points plot below the solid solubility limit defined by Reich et al. (2005) indicate that Au1+ is the dominant form of Au in arsenian pyrite and that Au-bearing ore fluids that deposit this sulfide are mostly undersaturated with respect to native Au. The analytical data also show that the solid solubility limit of Au in arsenian pyrite defined by an Au/As ratio of 0.02 is independent of the geochemical environment of pyrite formation and rather depends on the crystal-chemical properties of pyrite and post-depositional alteration. Compilation of Au-As concentrations and formation temperatures for pyrite indicates that Au and As solubility in pyrite is retrograde; Au and As contents decrease as a function of increasing temperature from ∼200 to ∼500 °C. Based on these results, two major Au-As trends for Au-bearing arsenian pyrite from ore deposits are defined. One trend is formed by pyrites from Carlin-type and orogenic Au deposits where compositions are largely controlled by fluid-rock interactions and/or can be highly perturbed by changes in temperature and

Origin of high-grade gold ore, source of ore fluid components, and genesis of the Meikle and neighboring Carlin-type deposits, Northern Carlin Trend, Nevada

USGS Publications Warehouse

Emsbo, P.; Hofstra, A.H.; Lauha, E.A.; Griffin, G.L.; Hutchinson, R.W.

2003-01-01

The Meikle mine exploits one of the world's highest grade Carlin-type gold deposits with reserves of ca. 220 t gold at an average grade of 24.7 g/t. Locally, gold grades exceed 400 g/t. Several geologic events converged at Meikle to create these spectacular gold grades. Prior to mineralization, a Devonian hydrothermal system altered the Bootstrap limestone to Fe-rich dolomite. Subsequently the rocks were brecciated by faulting and Late Jurassic intrusive activity. The resulting permeability focused flow of late Eocene Carlin-type ore fluids and allowed them to react with the Fe-rich dolomite. Fluid inclusion data and mineral assemblages indicate that these fluids were hot (ca. 220??C),of moderate salinity (400 g/t. Petrographic observations, geochemical data, and stable isotope results from the Meikle mine and other deposits at the Goldstrike mine place important constraints on genetic models for Meikle and other Carlin-type gold deposits on the northern Carlin trend. The ore fluids were meteoric water (??D = -135???, ??18O = -5???) that interacted with sedimentary rocks at a water/rock ratio of ca. 1 and temperatures of ca. 220??C. The absence of significant silicification suggests that there was little cooling of the ore fluids during mineralization. These two observations strongly suggest that ore fluids were not derived from deep sources but instead flowed parallel to isotherms. The gold was transported by H2S (??34S = 9???), which was derived from Paleozoic sedimentary rocks. The presence of auriferous sedimentary exhalative mineralization in the local stratigraphic sequence raises the possibility that preexisting concentrations of gold contributed to the Carlin-type deposits. Taken together our observations suggest that meteoric water evolved to become an ore fluid by shallow circulation through previously gold- and sulfur-enriched rocks. Carlin-type gold deposits formed where these fluids encountered permeable, reactive Fe-rich rocks.

Application of LANDSAT satellite imagery for iron ore prospecting in the western desert of Egypt

NASA Technical Reports Server (NTRS)

Elshazly, E. M.; Abdel-Hady, M. A.; Elghawaby, M. A.; Khawasik, S. M. (Principal Investigator)

1977-01-01

The author has identified the following significant results. The delineation of the geological units and geological structures through image interpretation, corroborated by field observations and structural analysis, led to the discovery of new iron ore deposits. A new locality for iron ore deposition, namely Gebel Qalamun, was discovered, as well as new occurrences within the already known iron ore region of Bahariya Oasis.

Physical-chemical conditions of ore deposition

USGS Publications Warehouse

Barton, P.B.

1981-01-01

Ore deposits form under a wide range of physical and chemical conditions, but those precipitating from hot, aqueous fluids-i.e. the hydrothermal deposits-form generally below 700??C and at pressures of only 1 or 2 kbar or less. Natural aqueous fluids in rocks may extract metal and sulfur from a variety of rock types or may acquire them as a residual heritage from a crystallizing silicate magma. Ore-forming hydrothermal fluids never appear as hot springs (except in deep, submarine situations) because they boil, mix with surface waters, and cool, thereby losing their ore-bearing ability before reaching the surface. Mineral systems function as chemical buffers and indicators just as buffers and indicators function in a chemical laboratory. By reading the record written in the buffer/indicator assemblages of minerals one can reconstruct many aspects of the former chemical environment. By studying the record of changing conditions one may deduce information regarding the processes functioning to create the succession of chemical environments and the ore deposits they represent. The example of the OH vein at Creede, Colorado, shows a pH buffered by the K-feldspar + muscovite + quartz assemblage and the covariation of S2 and O2 buffered by the assemblage chlorite + pyrite + quartz. Boiling of the ore fluid led to its oxidation to hematite-bearing assemblages and simultaneously produced an intensely altered, sericitic capping over the vein in response to the condensation of vapors bearing acidic components. The solubility of metals as calculated from experimental and theoretical studies of mineral solubility appears too low by at least one or two powers of ten to explain the mineralization at Creede. In contrast to Creede where the mineral stabilities all point to a relatively consistent chemistry, the Mississippi Valley type deposits present a puzzle of conflicting chemical clues that are impossible to reconcile with any single equilibrium situation. Thus we must

Geology of the manganese deposits of Cuba

USGS Publications Warehouse

Simons, Frank S.; Straczek, John A.

1958-01-01

Deposits of manganese ore have been found in five of the six provinces of Cuba and have been reported from the sixth.  Only Oriente and Pinar del Rio provinces have more than a few known deposits and only the deposits of Oriente have yielded any appreciable amount of ore.

Investigation of LANDSAT imagery on correlations between ore deposits and major shield structures in Finland

NASA Technical Reports Server (NTRS)

Tuominen, H. V. (Principal Investigator); Kuosmanen, V.

1977-01-01

The author has identified the following significant results. Several regional lineaments appear to correlate with the distribution of ore deposits and showings. Combined study of LANDSAT summer and winter mosaics and color composites of geological, geomorphological, and geophysical maps makes the correlation more perceptible. The revealed pattern of significant lineaments in northern Finland is fairly regular. The most significant lineaments seen in LANDSAT mosaics are not detectable in single images.

Volcanogenic Uranium Deposits: Geology, Geochemical Processes, and Criteria for Resource Assessment

USGS Publications Warehouse

Nash, J. Thomas

2010-01-01

Felsic volcanic rocks have long been considered a primary source of uranium for many kinds of uranium deposits, but volcanogenic uranium deposits themselves have generally not been important resources. Until the past few years, resource summaries for the United States or the world generally include volcanogenic in the broad category of 'other deposits' because they comprised less than 0.5 percent of past production or estimated resources. Exploration in the United States from the 1940s through 1982 discovered hundreds of prospects in volcanic rocks, of which fewer than 20 had some recorded production. Intensive exploration in the late 1970s found some large deposits, but low grades (less than about 0.10 percent U3O8) discouraged economic development. A few deposits in the world, drilled in the 1980s and 1990s, are now known to contain large resources (>20,000 tonnes U3O8). However, research on ore-forming processes and exploration for volcanogenic deposits has lagged behind other kinds of uranium deposits and has not utilized advances in understanding of geology, geochemistry, and paleohydrology of ore deposits in general and epithermal deposits in particular. This review outlines new ways to explore and assess for volcanogenic deposits, using new concepts of convection, fluid mixing, and high heat flow to mobilize uranium from volcanic source rocks and form deposits that are postulated to be large. Much can also be learned from studies of epithermal metal deposits, such as the important roles of extensional tectonics, bimodal volcanism, and fracture-flow systems related to resurgent calderas. Regional resource assessment is helped by genetic concepts, but hampered by limited information on frontier areas and undiscovered districts. Diagnostic data used to define ore deposit genesis, such as stable isotopic data, are rarely available for frontier areas. A volcanic environment classification, with three classes (proximal, distal, and pre-volcanic structures

RELATIONSHIP OF URANIUM ORE DEPOSITS TO PETROLEUM AND GAS-BEARING STRUCTURES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Russell, R.T.

eposits are located on producing or breached oil and gas structures, or in the immediate vicinity of such structures. Individual deposits associated with these structures contain ore reserves which may exceed one million tons. Data derived from a study of the known deposits should be useful in evaluating the potentiality of other areas where similar structural relations and abnormal radioactivity are known to exist. Uranium deposits located in producing oil or gas fields include a deposit of more than one million tons of uranium ore on a single salt dome in Texas, and uranium deposits in the Poison Basin, Wyoming,more » which are situated over a producing naturalgas structure, having a potential of 100,000 to 200,000 tons. Important uranium mining districts are also located near producing oil fields or near structures which may have contained oil at some time in the past. The Gas Hills district to Wyoming is on the flanks of a breached anticline and within one mile of natural-gas seeps. Deposits in the Brown's Park formation near Maybell, Colorado, are witin 10 miles of producing oil wells and natural-gas seeps are known within one mile of some of the uranium mines; and at Morrison, Colorado, uranium ore is associated with tar seeps. On th Colorado Plateau, large ore bodies with total reserves of at least 30 million tons of 0.3% U/sub 3/O/sub 8/ ore in the Ambrosia Lake district near Grants, New Mexico, and produce ore associated with asphaltite.'' The uraniferous asphaltite'' ore at Temple Mountain, Utah has been known for nearly 50 years. At both Circle Cliffs and the Inter- River area in Utah, uranium ore is associated with asphaltic material on anticlinal structures. Many other deposits are on breached strucIn Wyoming, uranium deposits in Tertiary sandstone and arkose generally lack carbon trash, but are located near oil or gas structures that contain hydrocarbons and natural gases capable of precititating uranium. Also, many uranium deposits on the Colorado

Mineralogy and fluid inclusions study of carbonate-hosted Mississippi valley-type Ain Allega Pb-Zn-Sr-Ba ore deposit, Northern Tunisia

NASA Astrophysics Data System (ADS)

Abidi, R.; Slim-Shimi, N.; Somarin, A.; Henchiri, M.

2010-05-01

The Ain Allega Pb-Zn-Sr-Ba ore deposit is located in the flysch zone on the Eastern edge of the Triassic diapir of Jebel Hamra. It is part of the extrusive Triassic evaporate formation along the Ghardimaou-Cape Serrat faults. The ore body consists of argilic-dolomite breccias surrounded by argilo-gypsum Triassic formation, which forms the hanging wall of the deposit, and rimmed by the Paleocene marls. The ore minerals show a cap-rock type mineralization with different styles particularly impregnation in dolomite, cement of breccias, replacement ore and open space filling in the dissolution cavities and fractures. Ore minerals include sphalerite, galena, marcasite and pyrite. Principal gangue minerals are composed of barite, celestite, calcite, dolomite and quartz. The ore minerals are hosted by the Triassic carbonate rocks which show hydrothermal alteration, dissolution and brecciation. X-ray - crystallographic study of barite-celestite mineral series shows that pure barite and celestite are the abundant species, whereas strontianiferous barite (85-96.5% BaSO 4) and barian-celestite (95% SrSO 4) are minor. Primary and secondary mono-phase (liquid only) fluid inclusions are common in celestite. Microthermometric analyses in two-phases (liquid and vapour) fluid inclusions suggest that gangue and ore minerals were precipitated by a low-temperature (180 °C) saline (16.37 wt.% NaCl equivalent) solution originated possibly from a basinal brine with some input from magmatic or metamorphic fluid. Based on geology, mineralogy, texture and fluid characteristics, the Ain Allega deposit is classified as a carbonate-hosted Mississippi valley-type deposit.

Geological and Geochemical Characteristics of Skarn Type Lead-Zinc Deposit in Baoshan Block, Yunnan Province

NASA Astrophysics Data System (ADS)

Yao, Xue; Wang, Peng

2017-11-01

Baoshan block is an important Pb-Zn-Fe-Cu polymetallic ore-concentration area which is located in southern of the Sanjiang metallogenic belt in western Yunnan. The article is studying about the geological and geochemical characteristics of the skarn type lead-zinc deposit in Baoshan block. The skarn-type lead-zinc deposit Baoshan block is characterized by skarn and skarn marble, and the orebodies are layered, or bedded along the interlayer fault, which are significantly controlled by structure. The research about Stable isotope S, H and O indicates that the ore-forming fluids are mainly derived from magmatic water, partly mixed with parts of metamorphic water and atmospheric precipitation. The initial Sr isotopic Sr87/Sr86 ratio suggests that the ore-forming materials derived from deep concealed magmatic rock, age of Rb-Sr mineralization is similar to that of Yanshanian granite. In conclusion, the Yanshanian tectonic-magmatic-fluid coupling mineralization of Yanshan formation is the main reason for the skarn-type lead-zinc deposit in the Baoshan block.

Blasting preparation for selective mining of complex structured ore deposition

NASA Astrophysics Data System (ADS)

Marinin, M. A.; Dolzhikov, V. V.

2017-10-01

Technological features of ore mining in the open pit development for processing of complex structured ore deposit of steeply falling occurrence have been considered. The technological schemes of ore bodies mining under different conditions of occurrence, consistency and capacity have been considered and offered in the paper. These technologies permit to reduce losses and dilution, but to increase the completeness and quality of mined ore. A method of subsequent selective excavation of ore bodies has been proposed. The method is based on the complex use of buffer-blasting technology for the muck mass and the principle of trim blasting at ore-rock junctions.

Geology, Geochemistry and Geophysics of Sedimentary Rock-Hosted Au Deposits in P.R. China

USGS Publications Warehouse

Peters, Stephen G.

2002-01-01

This is the second report concerning results of a joint project between the U.S. Geological Survey and the Tianjin Geological Academy to study sedimentary rock-hosted Au deposits in P.R. China. Since the 1980s, Chinese geologists have devoted a large-scale exploration and research effort to the deposits. As a result, there are more than 20 million oz of proven Au reserves in sedimentary rock-hosted Au deposits in P.R. China. Additional estimated and inferred resources are present in over 160 deposits and occurrences, which are undergoing exploration. This makes China second to Nevada in contained ounces of Au in Carlin-type deposits. It is likely that many of the Carlin-type Au ore districts in China, when fully developed, could have resource potential comparable to the multi-1,000-tonne Au resource in northern Nevada. The six chapters of this report describe sedimentary rock-hosted Au deposits that were visited during the project. Chapters 1 and 2 provide an overview of sedimentary rock-hosted Au deposits and Carlin-type Au deposits and also provide a working classification for the sedimentary rock-hosted Au deposits. Chapters 3, 4, and 5 provide descriptions that were compiled from the literature in China in three main areas: the Dian-Qian-Gui, the Qinling fold belt, and Middle-Lower Yangtze River areas. Chapter 6 contains a weights-of-evidence (WofE), GIS-based mineral assessment of sedimentary rock-hosted Au deposits in the Qinling fold belt and Dian-Qian-Gui areas. Appendices contain scanned aeromagnetic (Appendix I) and gravity (Appendix II) geophysical maps of south and central China. Data tables of the deposits (Appendix III) also are available in the first report as an interactive database at http://geopubs.wr.usgs.gov/open-file/of98-466/. Geochemical analysis of ore samples from the deposits visited are contained in Appendix IV.

Sedimentary carbonate-hosted giant Bayan Obo REE-Fe-Nb ore deposit of Inner Mongolia, China; a cornerstone example for giant polymetallic ore deposits of hydrothermal origin

USGS Publications Warehouse

Chao, E.C.T.; Back, J.M.; Minkin, J.A.; Tatsumoto, M.; Junwen, Wang; Conrad, J.E.; McKee, E.H.; Zonglin, Hou; Qingrun, Meng; Shengguang, Huang

1997-01-01

Detailed, integrative field and laboratory studies of the textures, structures, chemical characteristics, and isotopically determined ages and signatures of mineralization of the Bayan Obo deposit provided evidence for the origin and characteristics favorable for its formation and parameters necessary for defining giant polymetallic deposits of hydrothermal origin. Bayan Obo is an epigenetic, metasomatic, hydrothermal rare earth element (REE)-Fe-Nb ore deposit that is hosted in the metasedimentary H8 dolostone marble of the Middle Proterozoic Bayan Obo Group. The metasedimentary sequence was deposited on the northern continental slope of the North China craton. The mine area is about 100 km south of the suture marking Caledonian subduction of the Mongolian oceanic plate from the north beneath the North China craton. The mineralogy of the deposit is very complex, consisting of more than 120 different minerals, some of which are epigenetic minerals introduced by hydrothermal solutions, and some of which are primary and secondary metamorphic minerals. The major REE minerals are monazite and bastnaesite, whereas magnetite and hematite are the dominant Fe-ore minerals, and columbite is the most abundant Nb mineral. Dolomite, alkali amphibole, fluorite, barite, aegirine augite, apatite, phlogopite, albite, and microcline are the most widespread gangue minerals. Three general types of ores occur at Bayan Obo: disseminated, banded, and massive ores. Broad zoning of these ore types occurs in the Main and East Orebodies. Disseminated ores are in the outermost zone, banded ores are in the intermediate zone, and massive ores are in the cores of the orebodies. On the basis of field relations, host rocks, textures, structures, and mineral assemblages, many varieties of these three types of ores have been recognized and mapped. Isotopic dating of monazite, bastnaesite, aeschynite, and metamorphic and metasomatic alkali amphiboles associated with the deposit provides constraints

Geologic characteristics of sediment- and volcanic-hosted disseminated gold deposits - Search for an occurrence model

USGS Publications Warehouse

White, Donald E.; Fournier, Robert O.; Rytuba, James J.; Rye, Robert O.; Cunningham, Charles G.; Berger, Byron R.; Silberman, Miles L.; Bonham, Harold F.; Strachan, Donald G.; Birak, Donald J.; Hawkins, Robert J.; Tooker, Edwin W.; Tooker, Edwin W.

1985-01-01

The current expansion of resource information, particularly on "disseminated" gold, and the improved technologies now available for resource investigations should place us in an enhanced position for developing a better predictive methodology for meeting one of the important responsibilities of the U.S. Geological Survey-to examine and assess the mineral resources of the geologic terranes composing the public (and privately owned) lands of the United States. The first step is systematic organization of these data. Geologic-occurrence models are an effective systematic method by which to organize large amounts of resource information into a logical sequence facilitating its use more effectively in meeting several industry and Survey objectives, which include the exploration for resources and the assessment of resource potential for land-use decisions. Such models also provide a scientific basis for metallogenesis research, which considers the observable features or attributes of ore occurrence and their "fit" into the Earth's resource puzzle. The use of models in making resource assessments/appraisals was addressed by Shawe (1981), who reported the results of a workshop on methods for resource appraisal of Wilderness and Conterminous United States Mineral Appraisal Program (CUSMAP; 1:250,000-scale quadrangles) areas. The Survey's main objective in the 1982 workshop was to evaluate the status of knowledge about disseminated or very fine grained gold deposits and, if possible, to develop an occurrence model(s).This report on the workshop proceedings has three main objectives: (1) Education through the publication of a summary review and presentation of new thinking and observations about the scientific bases for those geologic processes and environments that foster disseminated gold-ore formation; (2) systematic organization of available geologic, geochemical, and geophysical information for a range of typical disseminated gold deposits (including recognition of gaps

Ore genesis of the Wusihe carbonate-hosted Zn-Pb deposit in the Dadu River Valley district, Yangtze Block, SW China: evidence from ore geology, S-Pb isotopes, and sphalerite Rb-Sr dating

NASA Astrophysics Data System (ADS)

Xiong, Suo-Fei; Gong, Yong-Jun; Jiang, Shao-Yong; Zhang, Xiao-Jing; Li, Qian; Zeng, Guo-Ping

2018-01-01

The Wusihe carbonate-hosted Zn-Pb deposit (3.7 Mt. Zn + Pb at a grade of 8.6% Zn and 2.0% Pb) is the largest deposit in the Dadu River Valley district of the Sichuan-Yunnan-Guizhou metallogenic province of southwest China. Three types of orebodies occur: (1) stratiform, banded and lamellar, within dolomite of the Neoproterozoic Dengying Formation; (2) vein type; and (3) breccia type. Four stages of mineralization are distinguished: (i) pyrite stage, (ii) pyrite-pyrrhotite-galena-sphalerite-bitumen stage, (iii) sphalerite-galena stage, and (iv) bitumen-calcite stage. Sphalerite and galena from stages II and III show δ34S ranges from +7.1 to +9.7‰ and +9.1 to +13.1‰, respectively. High-precision in situ lead isotope analyses of sulfides show 208Pb/204Pb, 207Pb/204Pb, and 206Pb/204Pb ratios of 37.938 to 38.336, 15.579 to 15.682, and 17.951 to 18.195, respectively, which suggest a mixing of lead from the basement and the host rocks. Rb-Sr isotope analyses for six sphalerite samples of stage II yielded an isochron age of 411 ± 10 Ma (MSWD = 1.4). Combining all available ore geology and geochemical data, together with fluid inclusion data reported previously, we suggest that the Wusihe deposit is a Mississippi Valley-type (MVT) deposit.

Geology and geochemistry of Carlin-type gold deposits in China

USGS Publications Warehouse

Rui-Zhong, H.; Wen-Chao, S.; Xian-Wu, B.; Guang-Zhi, T.; Hofstra, A.H.

2002-01-01

The Carlin-type gold deposits in China lie mostly near the margins of the Proterozoic Yangtze and Aba cratons. Submicron-sized gold in micron-sized arsenian pyrite is disseminated in fractured Cambrian through Triassic carbonaceous shale and carbonate rocks, and is associated with anomalous Hg, Sb, As, U, and Tl. Alteration typically includes silicification, argilization, and sulfidation. Aqueous fluid inclusions contain CO2, have relatively low temperatures of homogenization (250-150 ??C), and salinities (8-2 wt% equiv. NaCl) that typically decrease from early to later stages. The indicated pressures of 105-330x105 Pa correspond to depths in excess of 1.0 to 3.0 km, assuming hydrostatic conditions. The ??D values of fluid inclusions (-87 to -47%) and the calculated ??18 values for water in ore fluids (-2.1 to 16.2%) reflect interactions between meteoric water and sedimentary rocks. The ??13C values of calcite (-9 to 2%) and ??34S values of sulfides (-24 to 17%) suggest that C and S were derived from marine carbonate (and organic carbon) and diagenetic sulfides (and organic sulfur) in the vicinity of the deposits. Geologic relationships and geochronologic evidence indicate the deposits formed during a late phase of the Yanshanian orogeny (140-75 Ma). These gold deposits share much in common with the Carlin-type gold deposits in Nevada, USA. Both occur in carbonaceous, pyritic, sedimentary rocks deposited on extended margins of Precambrian cratons. The smaller Chinese deposits are generally in more siliceous rocks and the larger Nevada deposits in more calcareous rocks. In both countries, the host rocks prior to mineralization were affected by contractional deformation that produced many of the ore-controlling structures and the deposits do not show consistent spatial or genetic relationships with epizonal plutons. However, the Nevada deposits show broad spatial and temporal relationships with shifting patterns of calc-alkaline magmatism. The ore and alteration

Prospecting For Magnetite Ore Deposits With A Innovative Sensor's of Unique Fundamentally New Magnetometer.

NASA Astrophysics Data System (ADS)

Emelianenko, T. I.; Tachaytdinov, R. S.; Sarichev, V. F.; Kotov, B. V.; Susoeva, G. N.

erosional truncation level determination(Patent for invention N 2148844 dated 10.05.2000,M.,2000). Emelianenko T.I.,Tachaytdinov R.S.,Sarichev V.F.,Kotov B.V.,Susoeva G.N.2000.Fundamentally new magnetometer -locator for search magnetite ores (Abstracts of 31 International Geological Congress -Rio-de-Janeiro Brasil)at http www:// 31.igc.org. Emel ianenko T.I.,Matveev A.A. 2000.New geochemical method of quantity estimation of magnetite deposits(Abstracts of 31 International Geological Congress in Rio de Janeiro Brasil)at htt :www.31.igc.org. Emelianenko T.I.,Matveev A.A.2001.Fundamentally new geochemical method of quantitative of magnetite ore deposits(Abstracts of 20 International Geochemical Exploration Simposium,Santiago de Chile)at http ://aeg.org. Emelianenko T.I.,Matveev A.A.2001.Fundamentally new geochemical method of hypsometrical level of magnetite deposits ore zone.(Abstracts of 20 International Geochemical Exploration Symposium Santiago de Chile).at http:www.aeg.org. Nikitskiye V.E.,Glebovskiye J.S..Magnitoprospecting.M.N.1980. Nikitskiye V.E.,Glebovskiye J.S. Magnitoprospecting.M.,N.,1990. .Grinevitch G.I.Magnitoprospecting.M.,N.,1974.

A synthesis of mineralization styles and geodynamic settings of the Paleozoic and Mesozoic metallic ore deposits in the Altay Mountains, NW China

NASA Astrophysics Data System (ADS)

Yang, Fuquan; Geng, Xinxia; Wang, Rui; Zhang, Zhixin; Guo, Xuji

2018-06-01

The Altay Mountains within the Xinjiang region of northwestern China hosts major metallic ore deposits. Here we review the geological characteristics, metallogenic features and tectonic settings of these deposits. The metallic ore deposits in the Altay Mountains occur mainly within four regions: North Altay, Central Altay, South Altay and Erqis. We recognize seven types of metallic ore deposits in the Altay Mountains: VMS, submarine volcanogenic iron, magmatic, skarn, pegmatite, hydrothermal vein (Cu-Zn, Fe) and orogenic gold. Among these types, the VMS, pegmatite, orogenic gold and skarn deposits are the most common. Most of the rare metal pegmatite deposits are distributed in Central Altay, with only a few in South Altay. The VMS, submarine volcanogenic type iron and skarn-type deposits are distributed in South Altay, whereas the orogenic-type gold deposits are distributed in the Erqis Fault belt. The hydrothermal vein-type deposits occur in the Erqis Fault belt and Chonghu'er Basin in South Altay. Magmatic-type deposits are mostly in the Erqis Fault belt and Central Altay. Based on isotopic age data, the VMS, submarine volcanogenic-type Fe and skarn-type Cu, Pb, Zn, Fe mineralization occurred during Early-Middle Devonian (∼410-377 Ma), orogenic-type Au, magmatic-type Cu-Ni, and a small number of skarn-type Fe, hydrothermal vein-type Cu-Zn, pegmatite-type rare-metal deposits in Early-Middle Permian (293-261 Ma), pegmatite-type rare-metal deposits, few skarn-type Fe deposit in Early-Middle Triassic (248-232 Ma), and dominantly represented by pegmatite-type rare-metal deposits in Late Triassic-Early Jurassic (223-180 Ma). The metallic ore deposits in the Altay Mountains formed in various tectonic settings, such as the Early-Middle Devonian continental arc and oceanic island arc, Early-Middle Permian post-collisional extensional setting, and Triassic-Early Jurassic intracontinental setting.

Geological and geochemical aspects of uranium deposits: a selected, annotated bibliography. Vol. 2, Rev. 1. [490 references

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas, J.M.; Brock, M.L.; Garland, P.A.

1979-07-01

This bibliography, a compilation of 490 references, is the second in a series compiled from the National Uranium Resource Evaluation (NURE) Bibliographic Data Base. This data base is one of six data bases created by the Ecological Sciences Information Center, Oak Ridge National Laboratory, for the Grand Junction Office of the Department of Energy. Major emphasis for this volume has been placed on uranium geology, encompassing deposition, genesis of ore deposits, and ore controls; and prospecting techniques, including geochemistry and aerial reconnaissance. The following indexes are provided to aid the user in locating references of interest: author, geographic location, quadranglemore » name, geoformational feature, taxonomic name, and keyword.« less

Automated recognition of stratigraphic marker shales from geophysical logs in iron ore deposits

NASA Astrophysics Data System (ADS)

Silversides, Katherine; Melkumyan, Arman; Wyman, Derek; Hatherly, Peter

2015-04-01

The mining of stratiform ore deposits requires a means of determining the location of stratigraphic boundaries. A variety of geophysical logs may provide the required data but, in the case of banded iron formation hosted iron ore deposits in the Hamersley Ranges of Western Australia, only one geophysical log type (natural gamma) is collected for this purpose. The information from these logs is currently processed by slow manual interpretation. In this paper we present an alternative method of automatically identifying recurring stratigraphic markers in natural gamma logs from multiple drill holes. Our approach is demonstrated using natural gamma geophysical logs that contain features corresponding to the presence of stratigraphically important marker shales. The host stratigraphic sequence is highly consistent throughout the Hamersley and the marker shales can therefore be used to identify the stratigraphic location of the banded iron formation (BIF) or BIF hosted ore. The marker shales are identified using Gaussian Processes (GP) trained by either manual or active learning methods and the results are compared to the existing geological interpretation. The manual method involves the user selecting the signatures for improving the library, whereas the active learning method uses the measure of uncertainty provided by the GP to select specific examples for the user to consider for addition. The results demonstrate that both GP methods can identify a feature, but the active learning approach has several benefits over the manual method. These benefits include greater accuracy in the identified signatures, faster library building, and an objective approach for selecting signatures that includes the full range of signatures across a deposit in the library. When using the active learning method, it was found that the current manual interpretation could be replaced in 78.4% of the holes with an accuracy of 95.7%.

Difference in rockburst hazard in ore and coal mines

NASA Astrophysics Data System (ADS)

Lovchikov, AV

2018-03-01

In the Russian mining and engineering literature, in most cases, there is no difference in the assessment of the rockburst hazards in metal and coal mines. Nevertheless, it exists, in view of the difference in geological and geotechnical conditions of coal and ore deposits. Since ore deposits occur in the solid magmatic or metamorphic rock masses, the strongest induced earthquakes are much more powerful in ore mines than in coal mines. The main difference of rockbursting lies in the difference of natural stress state: gravity stress state in the coal fields and gravity-and-tectonic stress state in ore mines. The actual stresses are mostly vertical in the first case and horizontal in the second case, which conditions the difference in rockburst hazard in coal and ore mines.

Mineral deposits of Central America, with a section on manganese deposits of Panama

USGS Publications Warehouse

Roberts, Ralph Jackson; Irving, Earl Montgomery; Simons, F.S.

1957-01-01

The mineral deposits of Central America were studied between 1942 and 1945, in cooperation with the United States Department of State and the Foreign Economic Administration. Emphasis was originally placed on the study of strategic-mineral deposits, especially of antimony, chromite, manganese, quartz, and mica, but deposits of other minerals that offered promise of significant future production were also studied. A brief appraisal of the base-metal deposits was made, and deposits of iron ore in Honduras and of lead and zinc ores in Guatemala were mapped. In addition, studies were made of the regional geology of some areas, data were collected from many sources, and a new map of the geology of Central America was compiled.

The "chessboard" classification scheme of mineral deposits: Mineralogy and geology from aluminum to zirconium

NASA Astrophysics Data System (ADS)

Dill, Harald G.

2010-06-01

Economic geology is a mixtum compositum of all geoscientific disciplines focused on one goal, finding new mineral depsosits and enhancing their exploitation. The keystones of this mixtum compositum are geology and mineralogy whose studies are centered around the emplacement of the ore body and the development of its minerals and rocks. In the present study, mineralogy and geology act as x- and y-coordinates of a classification chart of mineral resources called the "chessboard" (or "spreadsheet") classification scheme. Magmatic and sedimentary lithologies together with tectonic structures (1 -D/pipes, 2 -D/veins) are plotted along the x-axis in the header of the spreadsheet diagram representing the columns in this chart diagram. 63 commodity groups, encompassing minerals and elements are plotted along the y-axis, forming the lines of the spreadsheet. These commodities are subjected to a tripartite subdivision into ore minerals, industrial minerals/rocks and gemstones/ornamental stones. Further information on the various types of mineral deposits, as to the major ore and gangue minerals, the current models and the mode of formation or when and in which geodynamic setting these deposits mainly formed throughout the geological past may be obtained from the text by simply using the code of each deposit in the chart. This code can be created by combining the commodity (lines) shown by numbers plus lower caps with the host rocks or structure (columns) given by capital letters. Each commodity has a small preface on the mineralogy and chemistry and ends up with an outlook into its final use and the supply situation of the raw material on a global basis, which may be updated by the user through a direct link to databases available on the internet. In this case the study has been linked to the commodity database of the US Geological Survey. The internal subdivision of each commodity section corresponds to the common host rock lithologies (magmatic, sedimentary, and

Antimony ore in the Fairbanks district, Alaska

USGS Publications Warehouse

Killeen, Pemberton Lewis; Mertie, John B.

1951-01-01

Antimony-bearing ores in the Fairbanks district, Alaska, are found principally in two areas, the extremities of which are at points 10 miles west and 23 miles northeast of Fairbanks; and one of two minor areas lies along this same trend 30 miles farther to the northeast. These areas are probably only local manifestations of mineralization that affected a much broader area and formed antimony-bearing deposits in neighboring districts, the closest of which is 50 miles away. The ores were exposed largely as a result of lode gold mining, but at two periods in the past, high prices for antimony ore warranted an independent production and about 2500 tons of stibnite ore was shipped. The sulfide deposits occupy the same fractures along which a gold-quartz mineralization of greater economic importance occurred; and both are probably genetically related to igneous rocks which intrude the schistose country rock. The sulfide is in part contemporaneous with some late-stage quartz in which it occurs as disseminated crystals; and in part the latest filling in the mineralized zones where it forms kidney-shaped masses of essentially solid sulfide. One extremely long mass must have contained nearly 100 tons of ore, but the average of the larger kidneys is closer to several tons. Much of the ore is stibnite, with quartz as a minor impurity, and assays show the tenor to vary from 40 to 65 percent antimony. Sulphantimonites are less abundant but likewise occur as disseminated crystals and as kidney-shaped bodies. Antimony oxides appear on the weathered surface and along fractures within the sulfide ore. Deposits containing either stibnite or sulphantimonite are known at more than 50 localities, but only eighteen have produced ore and the bulk of this came from the mines. The geology of the deposit, and the nature, extent, and period of the workings are covered in the detailed descriptions of individual occurrences. Several geologic and economic factors, which greatly affect

Ore-fluid evolution at the Getchell Carlin-type gold deposit, Nevada, USA

USGS Publications Warehouse

Cline, J.S.; Hofstra, A.A.

2000-01-01

Minerals and fluid-inclusion populations were examined using petrography, microthermometry, quadrupole mass-spectrometer gas analyses and stable-isotope studies to characterize fluids responsible for gold mineralization at the Getchell Carlin-type gold deposit. The gold-ore assemblage at Getchell is superimposed on quartz-pyrite vein mineralization associated with a Late-Cretaceous granodiorite stock that intruded Lower-Paleozoic sedimentary rocks. The ore assemblage, of mid-Tertiary age, consists of disseminated arsenian pyrite that contains submicrometer gold, jasperoid quartz, and later fluorite and orpiment that fill fractures and vugs. Late ore-stage realgar and calcite enclose ore-stage minerals. Pre-ore quartz trapped fluids with a wide range of salinities (1 to 21 wt.% NaCl equivalent), gas compositions (H2O, CO2, and CH4), and temperatures (120 to >360??C). Oxygen- and hydrogen-isotope ratios indicate that pre-ore fluids likely had a magmatic source, and were associated with intrusion of the granodiorite stock and related dikes. Ore-stage jasperoid contains moderate salinity, aqueous fluid inclusions trapped at 180 to 220??C. Ore fluids contain minor CO2 and trace H2S that allowed the fluid to react with limestone host rocks and transport gold, respectively. Aqueous inclusions in fluorite indicate that fluid temperatures declined to ~175??C by the end of ore-stage mineralization. As the hydrothermal system collapsed, fluid temperatures declined to 155 to 115??C and realgar and calcite precipitated. Inclusion fluids in ore-stage minerals have high ??D(H2O) and ??18O(H2O) values that indicate that the fluid had a deep source, and had a metamorphic or magmatic origin, or both. Late ore-stage fluids extend to lower ??D(H2O) values, and have a wider range of ??18O(H2O) values suggesting dilution by variably exchanged meteoric waters. Results show that deeply sourced ore fluids rose along the Getchell fault system, where they dissolved carbonate wall rocks and

Robotic complex for the development of thick steeply-inclined coal seams and ore deposits

NASA Astrophysics Data System (ADS)

Nikitenko, M. S.; Malakhov, Yu V.; Neogi, Biswarup; Chakraborty, Pritam; Banerjee, Dipesu

2017-09-01

Proposal for the formulation of robotic complexes for steeply inclined coal seams as a basis of the supportive-enclosing walking module and power support with a controlled outlet for mining industry has been represented in this literature. In mining industry, the available resource base reserves and mineral deposits are concentrated deep down the earth crust leading towards a complicated geological condition i.e. abrupt ore bedding and steeply inclined strata with the high gas content and fire hazard of thick coal stratum, heading against an unfavorable and sometimes human labor life risk during subversive mining. Prevailing towards the development of effective robotic complexes based on the means of “unmanned technologies” for extraction of minerals from hard-to-reach deposits and make sure the safety of underground staff during sublevel mining technology.

The origin of Cu/Au ratios in porphyry-type ore deposits.

PubMed

Halter, Werner E; Pettke, Thomas; Heinrich, Christoph A

2002-06-07

Microanalysis of major and trace elements in sulfide and silicate melt inclusions by laser-ablation inductively coupled plasma mass spectrometry indicates a direct link between a magmatic sulfide liquid and the composition of porphyry-type ore deposits. Copper (Cu), gold (Au), and iron (Fe) are first concentrated in a sulfide melt during magmatic evolution and then released to an ore-forming hydrothermal fluid exsolved late in the history of a magma chamber. The composition of sulfide liquids depends on the initial composition and source of the magma, but it also changes during the evolution of the magma in the crust. Magmatic sulfide melts may exert the dominant direct control on the economic metal ratios of porphyry-type ore deposits.

Ore deposits in Africa and their relation to the underlying mantle

NASA Technical Reports Server (NTRS)

Liu, H.-S.

1981-01-01

African magmatism is largely related to the tensional stress regimes of the crust which are induced by the hotter upwelling mantle rocks. These mantle rocks may provide emanating forces and thermal energy for the upward movements of primary ore bodies with fluid inclusions in the tensional stress regimes of the crust. In this paper, the Goddard Earth Gravity Model is used to calculate a detailed subcrustal stress system exerted by mantle convection under Africa. The resulting system is found to be correlated with the African metallogenic provinces. Recognition of the full spectrum of ore deposits in Africa that may be associated with the hotter upwelling mantle rocks has provided an independent evidence to support the hypothesis of mantle-derived heat source for ore deposits.

Analysis of variance in investigations on anisotropy of Cu ore deposits

NASA Astrophysics Data System (ADS)

Namysłowska-Wilczyńska, B.

1986-10-01

The problem of variability of copper grades and ore thickness in the Lubin copper ore deposit in southwestern Poland is presented. Results of statistical analysis of variations of ledge parameters carried out for three exploited regions of the mine, representing different types of lithological profile show considerable differences. Variability of copper grades occurs in vertical profiles, as well as on extension of field (the copper-bearing series). Against the background of a complex, well-substantiated description of the spatial variability in the Lubin deposit, a methodology is presented that has been applied for the determination of homogeneous ore blocks. The method is a two-factorial (cross) analysis of variance with the special tests of Tukey, Scheffe and Duncan. Blocks of homogeneous sandstone ore have dimensions of up to 160,000 m2 and 60,000 m2 in the case of the Cu content parameter and 200,000 m2 and 10,000 m2 for the thickness parameter.

Rock-magnetism and ore microscopy of the magnetite-apatite ore deposit from Cerro de Mercado, Mexico

NASA Astrophysics Data System (ADS)

Alva-Valdivia, L. M.; Goguitchaichvili, A.; Urrutia-Fucugauchi, J.; Caballero-Miranda, C.; Vivallo, W.

2001-03-01

Rock-magnetic and microscopic studies of the iron ores and associated igneous rocks in the Cerro de Mercado, Mexico, were carried out to determine the magnetic mineralogy and origin of natural remanent magnetization (NRM), related to the thermo-chemical processes due to hydrothermalism. Chemical remanent magnetization (CRM) seems to be present in most of investigated ore and wall rock samples, replacing completely or partially an original thermoremanent magnetization (TRM). Magnetite (or Ti-poor titanomagnetite) and hematite are commonly found in the ores. Although hematite may carry a stable CRM, no secondary components are detected above 580°, which probably attests that oxidation occurred soon enough after the extrusion and cooling of the ore-bearing magma. NRM polarities for most of the studied units are reverse. There is some scatter in the cleaned remanence directions of the ores, which may result from physical movement of the ores during faulting or mining, or from perturbation of the ambient field during remanence acquisition by inhomogeneous internal fields within these strongly magnetic ore deposits. The microscopy study under reflected light shows that the magnetic carriers are mainly titanomagnetite, with significant amounts of ilmenite-hematite minerals, and goethite-limonite resulting from alteration processes. Magmatic titanomagnetites, which are found in igneous rocks, show trellis, sandwich, and composite textures, which are compatible with high temperature (deuteric) oxy-exsolution processes. Hydrothermal alteration in ore deposits is mainly indicated by martitization in oxide minerals. Grain sizes range from a few microns to >100 mm, and possible magnetic state from single to multidomain, in agreement with hysteresis measurements. Thermal spectra, continuous susceptibility measurements, and IRM (isothermal remanent magnetization) acquisition suggest a predominance of spinels as magnetic carriers, most probably titanomagnetites with low

The brown iron ores of west-middle Tennessee: Chapter D in Contributions to economic geology (short papers and preliminary reports), 1927: Part I - Metals and nonmetals except fuels

USGS Publications Warehouse

Burchard, E.F.

1927-01-01

A study of the brown iron ore deposits of west-middle Tennessee has been carried on recently under a cooperative agreement between the Tennessee State Geological Survey and the United States Geological Survey. A detailed report on the subject was submitted in the spring of 1925 to the State Survey for publication as a bulletin, and the writing of the present report was completed in March, 1926. The field work was done mainly between October 22 and November 2, 1921, and April 26 and July 18, 1923; but in October, 1924, a visit was made to the mine at Napier. The writer was assisted in the field in 1921 by. R. W. Smith, assistant geologist, and in 1923 by C. C. Anderson, topographer, both of the Tennessee Survey. Mr. Wilbur A. Nelson, State geologist at the time the work was in progress, visited several mines with the writer and on these occasions as well as many times during the preparation of the report rendered helpful suggestions and guidance. Mr. H. D. Miser, of the United States Geological Survey, State geologist from September 1, 1925, to July 1, 1926, who is especially familiar with the southern part of this area, also cooperated heartily in the preparation of this report; and Mr. H. W. Davis, of the United States Bureau of Mines, compiled the statistical data on iron ore and pig iron. To all these gentlemen the writer desires to express his appreciation. Acknowledgments are also due to the officials and employees of the iron mining and manufacturing companies and to people living in the vicinity of inactive mining properties for their courteous attention and for the large amount of information furnished.In the present paper the general features of the region and of the iron-ore deposits are delineated, but only a few typical ore deposits in each county are described, as the State bulletin will contain detailed descriptions of all properties.

A geologic assessment of potential lunar ores

NASA Technical Reports Server (NTRS)

Mckay, D. S.; Williams, R. J.

1979-01-01

Although bulk lunar soil is not a suitable feedstock for extracting metals, certain minerals such as anorthite and ilmenite can be separated and concentrated. These minerals can be considered as potential ores of aluminum, silicon, titanium, andiron. A separation and metal extraction plant could also extract large amounts of oxygen and perhaps hydrogen from these minerals. Anorthie containing 19 percent aluminum and 20 percent silicon can be concentrated from some highland soils where it is present in amounts up to 60 percent. Ilmenite containing 32 percent titanium and 37 percent iron can be concentrated from some mare soils where it is present in amounts up to 10 percent. The ideal mining site would be located at the boundary between a high-titanium mare and a high-aluminum highlands. Such area may exist around the rims of some eastern maria, particularly Tranquilitatis. A location on Earth with raw materials as described above would be considered an economically valuable ore deposit if conventional terrestrial resources were not available.

The role of magmas in the formation of hydrothermal ore deposits

USGS Publications Warehouse

Hedenquist, Jeffrey W.; Lowenstern, Jacob B.

1994-01-01

Magmatic fluids, both vapour and hypersaline liquid, are a primary source of many components in hydrothermal ore deposits formed in volcanic arcs. These components, including metals and their ligands, become concentrated in magmas in various ways from various sources, including subducted oceanic crust. Leaching of rocks also contributes components to the hydrothermal fluid—a process enhanced where acid magmatic vapours are absorbed by deeply circulating meteoric waters. Advances in understanding the hydrothermal systems that formed these ore deposits have come from the study of their active equivalents, represented at the surface by hot springs and volcanic fumaroles.

Possible lunar ores

NASA Technical Reports Server (NTRS)

Gillett, Stephen L.

1991-01-01

Despite the conventional wisdom that there are no lunar ores, geochemical considerations suggest that local concentrations of useful rare elements exist on the Moon in spite of its extreme dryness. The Moon underwent protracted igneous activity in its history, and certain magmatic processes can concentrate incompatible elements even if anhydrous. Such processes include: (1) separation of a magma into immiscible liquid phases (depending on composition, these could be silicate-silicate, silicate-oxide, silicate-sulfide, or silicate-salt); (2) cumulate deposits in layered igneous intrusions; and (3) concentrations of rare, refractory, lithophile elements (e.g., Be, Li, Zr) in highly differentiated, silica-rich magmas, as in the lunar granites. Terrestrial mining experience indicates that the single most important characteristic of a potential ore is its concentration of the desire element. The utility of a planet as a resource base is that the welter of interacting processes over geologic time can concentrate rare element automatically. This advantage is squandered if adequate exploration for ores is not first carried out.

Lead-isotopic, sulphur-isotopic, and trace-element studies of galena from the Silesian-Cracow Zn-Pb ores, polymetallic veins from the Gory Swietokrzyskie MTS, and the Myszkow porphyry copper deposit, Poland

USGS Publications Warehouse

Church, S.E.; Vaughn, R.B.; Gent, C.A.; Hopkins, R.T.

1996-01-01

Lead-isotopic data on galena samples collected from a paragenetically constrained suite of samples from the Silesian-Cracow ore district show no regional or paragenetically controlled lead-isotopic trends within the analytical reproducibility of the measurements. Furthermore, the new lead-isotopic data agree with previously reported lead-isotopic results (R. E. Zartman et al., 1979). Sulfur-isotopic analyses of ores from the Silesian-Cracow district as well as from vein ore from the Gory Swietokrzyskie Mts. and the Myszkow porphyry copper deposit, when coupled with trace-element data from the galena samples, clearly discriminate different hydrothermal ore-forming events. Lead-isotopic data from the Permian and Miocene evaporite deposits in Poland indicate that neither of these evaporite deposits were a source of metals for the Silesian-Cracow district ores. Furthermore, lead-isotopic data from these evaporite deposits and the shale residues from the Miocene halite samples indicate that the crustal evolution of lead in the central and western European platform in southern Poland followed normal crustal lead-isotopic growth, and that the isotopic composition of crustal lead had progressed beyond the lead-isotopic composition of lead in the Silesian-Cracow ores by Permian time. Thus, Mesozoic and Tertiary sedimentary flysch rocks can be eliminated as viable source rocks for the metals in the Silesian-Cracow Mississippi Valley-type (MVT) deposits. The uniformity of the isotopic composition of lead in the Silesian-Cracow ores, when coupled with the geologic evidence that mineralization must post-date Late Jurassic faulting (E. Gorecka, 1991), constrains the geochemical nature of the source region. The source of the metals is probably a well-mixed, multi-cycle molasse sequence of sedimentary rocks that contains little if any Precambrian metamorphic or granitic clasts (S. E. Church, R. B. Vaughn, 1992). If ore deposition was post Late Jurassic (about 150 m. y.) or later

CO2-rich and CO2-poor ore-forming fluids of porphyry molybdenum systems in two contrasting geologic setting: evidence from Shapinggou and Zhilingtou Mo deposits, South China

NASA Astrophysics Data System (ADS)

Ni, P.

2017-12-01

Porphyry deposits are the world most important source of Mo, accounting for more than 95% of world Mo production. Porphyry Mo deposits have been classified into Climax type and Endako type. The Climax type was generally formed in an intra-continental setting, and contain high contents of Mo (0.15-0.45 wt.%) and F (0.5-5 wt.%). In contrast, the Endako type was generated in a continental arc setting and featured by low concentrations of Mo (0.05-0.15 wt.%) and F (0.05-0.15 wt.%). The systematic comparison of ore fluids in two contrasting tectonic environments is still poorly constrained. In this study, the Shapinggou and Zhilingtou Mo deposits in South China were selected to present the contrasting ore-forming fluid features. The fluid inclusion study of Shapinggou Mo deposit suggest: Early barren quartz veins contain fluid inclusions with salinities of 7.9-16.9 wt% NaCl equiv . CO2 contents are high enough to be detected by Raman. Later molybdenite-quartz veins contain vapor-type fluid inclusions with lower salinities (0.1-7.4 wt% NaCl equiv) but higher CO2-contents, coexisting with brine inclusions with 32.9-50.9 wt% NaCl equiv. The fluid inclusion study on Zhilintou Mo deposit suggest : Early barren quartz veins contain mostly intermediate density fluid inclusions with salinities of 5.3-14.1 wt% NaCl equiv, whereas main-stage quartz-molybdenite veins contain vapor-rich fluid inclusions of 0.5-6.2 wt% NaClequiv coexisting with brine inclusions of 38.6-44.8 wt% NaCl equiv. In contrast to the Shapinggou Mo deposit, the fluid inclusions at Shizitou contain only minor amounts of CO2. This study suggests the two porphyry molybdenum deposits experienced a similar fluid evolution trend, from single-phase fluids at the premineralization stage to two-phase fluids at the mineralization stage. Fluid boiling occurred during the ore stage and probably promoted a rapid precipitation of molybdenite. Intensive phyllic alteration, CO2-poor ore-forming fluids, and continental arc

Sedimentary exhalative (sedex) zinc-lead-silver deposit model

USGS Publications Warehouse

Emsbo, Poul; Seal, Robert R.; Breit, George N.; Diehl, Sharon F.; Shah, Anjana K.

2016-10-28

This report draws on previous syntheses and basic research studies of sedimentary exhalative (sedex) deposits to arrive at the defining criteria, both descriptive and genetic, for sedex-type deposits. Studies of the tectonic, sedimentary, and fluid evolution of modern and ancient sedimentary basins have also been used to select defining criteria. The focus here is on the geologic characteristics of sedex deposit-hosting basins that contain greater than 10 million metric tons of zinc and lead. The enormous size of sedex deposits strongly suggests that basin-scale geologic processes are involved in their formation. It follows that mass balance constraints of basinal processes can provide a conceptual underpinning for the evaluation of potential ore-forming mechanisms and the identification of geologic indicators for ore potential in specific sedimentary basins. Empirical data and a genetic understanding of the physicochemical, geologic, and mass balance conditions required for each of these elements are used to establish a hierarchy of quantifiable geologic criteria that can be used in U.S. Geological Survey national assessments.  In addition, this report also provides a comprehensive evaluation of environmental considerations associated with the mining of sedex deposits.

Porphyry-Style Petropavlovskoe Gold Deposit, the Polar Urals: Geological Position, Mineralogy, and Formation Conditions

NASA Astrophysics Data System (ADS)

Vikentyev, I. V.; Mansurov, R. Kh.; Ivanova, Yu. N.; Tyukova, E. E.; Sobolev, I. D.; Abramova, V. D.; Vykhristenko, R. I.; Trofimov, A. P.; Khubanov, V. B.; Groznova, E. O.; Dvurechenskaya, S. S.; Kryazhev, S. G.

2017-11-01

Geological and structural conditions of localization, hydrothermal metasomatic alteration, and mineralization of the Petropavlovskoe gold deposit (Novogodnenskoe ore field) situated in the northern part of the Lesser Ural volcanic-plutonic belt, which is a constituent of the Middle Paleozoic island-arc system of the Polar Urals, are discussed. The porphyritic diorite bodies pertaining to the late phase of the intrusive Sob Complex play an ore-controlling role. The large-volume orebodies are related to the upper parts of these intrusions. Two types of stringer-disseminated ores have been revealed: (1) predominant gold-sulfide and (2) superimposed low-sulfide-gold-quartz ore markedly enriched in Au. Taken together, they make up complicated flattened isometric orebodies transitory to linear stockworks. The gold potential of the deposit is controlled by pyrite-(chlorite)-albite metasomatic rock of the main productive stage, which mainly develops in a volcanic-sedimentary sequence especially close to the contacts with porphyritic diorite. The relationships between intrusive and subvolcanic bodies and dating of individual zircon crystals corroborate a multistage evolution of the ore field, which predetermines its complex hydrothermal history. Magmatic activity of mature island-arc plagiogranite of the Sob Complex and monzonite of the Kongor Complex initiated development of skarn and beresite alterations accompanied by crystallization of hydrothermal sulfides. In the Early Devonian, due to emplacement of the Sob Complex at a depth of approximately 2 km, skarn magnetite ore with subordinate sulfides was formed. At the onset of the Middle Devonian, the large-volume gold porphyry Au-Ag-Te-W ± Mo,Cu stockworks related to quartz diorite porphyry—the final phase of the Sob Complex— were formed. In the Late Devonian, a part of sulfide mineralization was redistributed with the formation of linear low-sulfide quartz vein zones. Isotopic geochemical study has shown that the

Discrimination of iron ore deposits of granulite terrain of Southern Peninsular India using ASTER data

NASA Astrophysics Data System (ADS)

Rajendran, Sankaran; Thirunavukkarasu, A.; Balamurugan, G.; Shankar, K.

2011-04-01

This work describes a new image processing technique for discriminating iron ores (magnetite quartzite deposits) and associated lithology in high-grade granulite region of Salem, Southern Peninsular India using visible, near-infrared and short wave infrared reflectance data of Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER). Image spectra show that the magnetite quartzite and associated lithology of garnetiferrous pyroxene granulite, hornblende biotite gneiss, amphibolite, dunite, and pegmatite have absorption features around spectral bands 1, 3, 5, and 7. ASTER band ratios ((1 + 3)/2, (3 + 5)/4, (5 + 7)/6) in RGB are constructed by summing the bands representing the shoulders of absorption features as a numerator, and the band located nearest the absorption feature as a denominator to map iron ores and band ratios ((2 + 4)/3, (5 + 7)/6, (7 + 9)/8) in RGB for associated lithology. The results show that ASTER band ratios ((1 + 3)/2, (3 + 5)/4, (5 + 7)/6) in a Red-Green-Blue (RGB) color combination identifies the iron ores much better than previously published ASTER band ratios analysis. A Principal Component Analysis (PCA) is applied to reduce redundant information in highly correlated bands. PCA (3, 2, and 1 for iron ores and 5, 4, 2 for granulite rock) in RGB enabled the discrimination between the iron ores and garnetiferrous pyroxene granulite rock. Thus, this image processing technique is very much suitable for discriminating the different types of rocks of granulite region. As outcome of the present work, the geology map of Salem region is provided based on the interpretation of ASTER image results and field verification work. It is recommended that the proposed methods have great potential for mapping of iron ores and associated lithology of granulite region with similar rock units of granulite regions of Southern Peninsular India. This work also demonstrates the ability of ASTER's to provide information on iron ores, which is valuable

Bio-mineralization and potential biogeochemical processes in bauxite deposits: genetic and ore quality significance

NASA Astrophysics Data System (ADS)

Laskou, Magdalini; Economou-Eliopoulos, Maria

2013-08-01

The Parnassos-Ghiona bauxite deposit in Greece of karst type is the 11th largest bauxite producer in the world. The mineralogical, major and trace-element contents and δ18O, δ12C, δ34S isotopic compositions of bauxite ores from this deposit and associated limestone provide valuable evidence for their origin and biogeochemical processes resulting in the beneficiation of low grade bauxite ores. The organic matter as thin coal layers, overlying the bauxite deposits, within limestone itself (negative δ12C isotopic values) and the negative δ34S values in sulfides within bauxite ores point to the existence of the appropriate circumstances for Fe bio-leaching and bio-mineralization. Furthermore, a consortium of microorganisms of varying morphological forms (filament-like and spherical to lenticular at an average size of 2 μm), either as fossils or presently living and producing enzymes, is a powerful factor to catalyze the redox reactions, expedite the rates of metal extraction and provide alternative pathways for metal leaching processes resulting in the beneficiation of bauxite ore.

Geology Exchange Program

NASA Astrophysics Data System (ADS)

Because geology professors cannot bring ore deposits from around the globe into their classrooms, the next best thing is to take their students to the deposits, according to David Norman, an associate professor of geochemistry at New Mexico Tech and Angus Moore of the Royal School of Mines. They organized a new exchange program between the New Mexico Institute of Mining and Technology in Socorro, N.M., and the Royal School of Mines in London, England. In May, 14 students from England toured deposits in New Mexico, Arizona, Utah, and Colorado; in the photograph, Norman (on the right) describes a rock from a New Mexico ore deposit to some of the visitors from England. In early June a contingency from New Mexico Tech began studying deposits in England, Spain, and Portugal. Norman and Moore say that the exchange program may be expanded next year.

A new model for tabular-type uranium deposits

USGS Publications Warehouse

Sanford, R.F.

1992-01-01

Tabular-type uranium deposits occur as tabular, originally subhorizontal bodies entirely within reduced fluvial sandstones of Late Silurian age or younger. This paper proposes that belts of tabular-type uranium deposits formed in areas of mixed local and regional groundwater discharge shortly after deposition of the host sediments. The general characteristics of tabular-type uranium deposits indicate that their essential feature was the formation at a density-stratified ground-water interface in areas of local and regional ground-water discharge. Reconstruction of the paleohydrogeology is the key to understanding the formation of these deposits. Geologic ground-water controls that favor discharge, such as the pinch-out of major aquifers, are also favorable for uranium ore. The combination of topographic and geologic features that both cause discharge is most favorable for ore deposition. -from Author

Massive deep-sea sulphide ore deposits discovered on the East Pacific Rise

USGS Publications Warehouse

Francheteau, Jean; Needham, H.D.; Choukroune, P.; Juteau, Tierre; Seguret, M.; Ballard, Richard D.; Fox, P.J.; Normark, William; Carranza, A.; Cordoba, D.; Guerrero, J.; Rangin, C.; Bougault, H.; Cambon, P.; Hekinian, R.

1979-01-01

Massive ore-grade zinc, copper and iron sulphide deposits have been found at the axis of the East Pacific Rise. Although their presence on the deep ocean-floor had been predicted there was no supporting observational evidence. The East Pacific Rise deposits represent a modern analogue of Cyprus-type sulphide ores associated with ophiolitic rocks on land. They contain at least 29% zinc metal and 6% metallic copper. Their discovery will provide a new focus for deep-sea exploration, leading to new assessments of the concentration of metals in the upper layers of the oceanic crust. ?? 1979 Nature Publishing Group.

Alfred E. Bergeat (1866-1924): a distinguished volcanologist and ore deposit researching scientist at the mining academies of Freiberg (Saxony) and Clausthal (Harz mountains) in Germany

NASA Astrophysics Data System (ADS)

Pfaffl, Fritz A.

2010-06-01

Alfred E. Bergeat, originated from a family, who produced gold-glance in a factory (porcelain painting), studied mineralogy and geology at the University of Munich from 1886 to 1892. Due to the results of his habilitation work on the volcanism of island arcs, especially of the Stromboli volcanic island in the Tyrrhenian Sea, he became a recognized volcanologist and specialist in volcanic petrography. He further became an explorer of syngenetic, epigenetic and deuterogenic ore deposits at the mining academies (Bergakademien) of Freiberg (Saxony) and Clausthal (Harz mountains). He described these ore deposits in a two-volume manual (1904-1906) which was summarized again in 1913. After his early death in 1924, the two manuals “Die Vulkane” (1925) and “Vulkankunde” (1927) were posthumously published by his colleague and friend Karl Sapper (1866-1945).

Chemical and Sr isotopic characterization of North America uranium ores: Nuclear forensic applications

DOE PAGES

Balboni, Enrica; Jones, Nina; Spano, Tyler; ...

2016-08-31

This study reports major, minor, and trace element data and Sr isotope ratios for 11 uranium ore (uraninite, UO 2+x) samples and one processed uranium ore concentrate (UOC) from various U.S. deposits. The uraninite investigated represent ores formed via different modes of mineralization (e.g., high- and low-temperature) and within various geological contexts, which include magmatic pegmatites, metamorphic rocks, sandstone-hosted, and roll front deposits. In situ trace element data obtained by laser ablation-ICP-MS and bulk sample Sr isotopic ratios for uraninite samples investigated here indicate distinct signatures that are highly dependent on the mode of mineralization and host rock geology. Relativemore » to their high-temperature counterparts, low-temperature uranium ores record high U/Th ratios (>1000), low total rare earth element (REE) abundances (<1 wt%), high contents (>300 ppm) of first row transition metals (Sc, Ti, V, Cr, Mn, Co, Ni), and radiogenic 87Sr/ 86Sr ratios (>0.7200). Comparison of chondrite normalized REE patterns between uraninite and corresponding processed UOC from the same locality indicates identical patterns at different absolute concentrations. Lastly, this result ultimately confirms the importance of establishing geochemical signatures of raw, uranium ore materials for attribution purposes in the forensic analysis of intercepted nuclear materials.« less

Chemical and Sr isotopic characterization of North America uranium ores: Nuclear forensic applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Balboni, Enrica; Jones, Nina; Spano, Tyler

This study reports major, minor, and trace element data and Sr isotope ratios for 11 uranium ore (uraninite, UO 2+x) samples and one processed uranium ore concentrate (UOC) from various U.S. deposits. The uraninite investigated represent ores formed via different modes of mineralization (e.g., high- and low-temperature) and within various geological contexts, which include magmatic pegmatites, metamorphic rocks, sandstone-hosted, and roll front deposits. In situ trace element data obtained by laser ablation-ICP-MS and bulk sample Sr isotopic ratios for uraninite samples investigated here indicate distinct signatures that are highly dependent on the mode of mineralization and host rock geology. Relativemore » to their high-temperature counterparts, low-temperature uranium ores record high U/Th ratios (>1000), low total rare earth element (REE) abundances (<1 wt%), high contents (>300 ppm) of first row transition metals (Sc, Ti, V, Cr, Mn, Co, Ni), and radiogenic 87Sr/ 86Sr ratios (>0.7200). Comparison of chondrite normalized REE patterns between uraninite and corresponding processed UOC from the same locality indicates identical patterns at different absolute concentrations. Lastly, this result ultimately confirms the importance of establishing geochemical signatures of raw, uranium ore materials for attribution purposes in the forensic analysis of intercepted nuclear materials.« less

Precipitation of lead-zinc ores in the Mississippi Valley-type deposit at Treves, Cevennes region of southern France

USGS Publications Warehouse

Leach, D.; Macquar, J.-C.; Lagneau, V.; Leventhal, J.; Emsbo, P.; Premo, W.

2006-01-01

The Trèves zinc–lead deposit is one of several Mississippi Valley-type (MVT) deposits in the Cévennes region of southern France. Fluid inclusion studies show that the ore was deposited at temperatures between approximately 80 and 150°C from a brine that derived its salinity mainly from the evaporation of seawater past halite saturation. Lead isotope studies suggest that the metals were extracted from local basement rocks. Sulfur isotope data and studies of organic matter indicate that the reduced sulfur in the ores was derived from the reduction of Mesozoic marine sulfate by thermochemical sulfate reduction or bacterially mediated processes at a different time or place from ore deposition. The large range of δ34S values determined for the minerals in the deposit (12.2–19.2‰ for barite, 3.8–13.8‰ for sphalerite and galena, and 8.7 to −21.2‰ for pyrite), are best explained by the mixing of fluids containing different sources of sulfur. Geochemical reaction path calculations, based on quantitative fluid inclusion data and constrained by field observations, were used to evaluate possible precipitation mechanisms. The most important precipitation mechanism was probably the mixing of fluids containing different metal and reduced sulfur contents. Cooling, dilution, and changes in pH of the ore fluid probably played a minor role in the precipitation of ores. The optimum results that produced the most metal sulfide deposition with the least amount of fluid was the mixing of a fluid containing low amounts of reduced sulfur with a sulfur-rich, metal poor fluid. In this scenario, large amounts of sphalerite and galena are precipitated, together with smaller quantities of pyrite precipitated and dolomite dissolved. The relative amounts of metal precipitated and dolomite dissolved in this scenario agree with field observations that show only minor dolomite dissolution during ore deposition. The modeling results demonstrate the important control of the reduced

Biogenic non-crystalline U(IV) revealed as major component in uranium ore deposits

NASA Astrophysics Data System (ADS)

Bhattacharyya, Amrita; Campbell, Kate M.; Kelly, Shelly D.; Roebbert, Yvonne; Weyer, Stefan; Bernier-Latmani, Rizlan; Borch, Thomas

2017-06-01

Historically, it is believed that crystalline uraninite, produced via the abiotic reduction of hexavalent uranium (U(VI)) is the dominant reduced U species formed in low-temperature uranium roll-front ore deposits. Here we show that non-crystalline U(IV) generated through biologically mediated U(VI) reduction is the predominant U(IV) species in an undisturbed U roll-front ore deposit in Wyoming, USA. Characterization of U species revealed that the majority (~58-89%) of U is bound as U(IV) to C-containing organic functional groups or inorganic carbonate, while uraninite and U(VI) represent only minor components. The uranium deposit exhibited mostly 238U-enriched isotope signatures, consistent with largely biotic reduction of U(VI) to U(IV). This finding implies that biogenic processes are more important to uranium ore genesis than previously understood. The predominance of a relatively labile form of U(IV) also provides an opportunity for a more economical and environmentally benign mining process, as well as the design of more effective post-mining restoration strategies and human health-risk assessment.

Biogenic non-crystalline U(IV) revealed as major component in uranium ore deposits

PubMed Central

Bhattacharyya, Amrita; Campbell, Kate M.; Kelly, Shelly D.; Roebbert, Yvonne; Weyer, Stefan; Bernier-Latmani, Rizlan; Borch, Thomas

2017-01-01

Historically, it is believed that crystalline uraninite, produced via the abiotic reduction of hexavalent uranium (U(VI)) is the dominant reduced U species formed in low-temperature uranium roll-front ore deposits. Here we show that non-crystalline U(IV) generated through biologically mediated U(VI) reduction is the predominant U(IV) species in an undisturbed U roll-front ore deposit in Wyoming, USA. Characterization of U species revealed that the majority (∼58-89%) of U is bound as U(IV) to C-containing organic functional groups or inorganic carbonate, while uraninite and U(VI) represent only minor components. The uranium deposit exhibited mostly 238U-enriched isotope signatures, consistent with largely biotic reduction of U(VI) to U(IV). This finding implies that biogenic processes are more important to uranium ore genesis than previously understood. The predominance of a relatively labile form of U(IV) also provides an opportunity for a more economical and environmentally benign mining process, as well as the design of more effective post-mining restoration strategies and human health-risk assessment. PMID:28569759

Biogenic non-crystalline U (IV) revealed as major component in uranium ore deposits

DOE PAGES

Bhattacharyya, Amrita; Campbell, Kate M.; Kelly, Shelly D.; ...

2017-06-01

Historically, it is believed that crystalline uraninite, produced via the abiotic reduction of hexavalent uranium (U (VI)) is the dominant reduced U species formed in low-temperature uranium roll-front ore deposits. Here we show that non-crystalline U (IV) generated through biologically mediated U (VI) reduction is the predominant U (IV) species in an undisturbed U roll-front ore deposit in Wyoming, USA. Characterization of U species revealed that the majority (~58-89%) of U is bound as U (IV) to C-containing organic functional groups or inorganic carbonate, while uraninite and U (VI) represent only minor components. The uranium deposit exhibited mostly 238U-enriched isotopemore » signatures, consistent with largely biotic reduction of U (VI) to U (IV). This finding implies that biogenic processes are more important to uranium ore genesis than previously understood. The predominance of a relatively labile form of U (IV) also provides an opportunity for a more economical and environmentally benign mining process, as well as the design of more effective post-mining restoration strategies and human health-risk assessment.« less

Biogenic non-crystalline U(IV) revealed as major component in uranium ore deposits.

PubMed

Bhattacharyya, Amrita; Campbell, Kate M; Kelly, Shelly D; Roebbert, Yvonne; Weyer, Stefan; Bernier-Latmani, Rizlan; Borch, Thomas

2017-06-01

Historically, it is believed that crystalline uraninite, produced via the abiotic reduction of hexavalent uranium (U (VI) ) is the dominant reduced U species formed in low-temperature uranium roll-front ore deposits. Here we show that non-crystalline U (IV)  generated through biologically mediated U (VI)  reduction is the predominant U (IV)  species in an undisturbed U roll-front ore deposit in Wyoming, USA. Characterization of U species revealed that the majority (∼58-89%) of U is bound as U (IV) to C-containing organic functional groups or inorganic carbonate, while uraninite and U (VI) represent only minor components. The uranium deposit exhibited mostly 238 U-enriched isotope signatures, consistent with largely biotic reduction of U (VI) to U (IV) . This finding implies that biogenic processes are more important to uranium ore genesis than previously understood. The predominance of a relatively labile form of U (IV) also provides an opportunity for a more economical and environmentally benign mining process, as well as the design of more effective post-mining restoration strategies and human health-risk assessment.

Biogenic non-crystalline U (IV) revealed as major component in uranium ore deposits

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bhattacharyya, Amrita; Campbell, Kate M.; Kelly, Shelly D.

Historically, it is believed that crystalline uraninite, produced via the abiotic reduction of hexavalent uranium (U (VI)) is the dominant reduced U species formed in low-temperature uranium roll-front ore deposits. Here we show that non-crystalline U (IV) generated through biologically mediated U (VI) reduction is the predominant U (IV) species in an undisturbed U roll-front ore deposit in Wyoming, USA. Characterization of U species revealed that the majority (~58-89%) of U is bound as U (IV) to C-containing organic functional groups or inorganic carbonate, while uraninite and U (VI) represent only minor components. The uranium deposit exhibited mostly 238U-enriched isotopemore » signatures, consistent with largely biotic reduction of U (VI) to U (IV). This finding implies that biogenic processes are more important to uranium ore genesis than previously understood. The predominance of a relatively labile form of U (IV) also provides an opportunity for a more economical and environmentally benign mining process, as well as the design of more effective post-mining restoration strategies and human health-risk assessment.« less

Geodynamic simulation of ore-bearing geological structural units by the example of the Strel'tsovka uranium ore field

NASA Astrophysics Data System (ADS)

Petrov, V. A.; Leksin, A. B.; Pogorelov, V. V.; Rebetsky, Yu. L.; San'kov, V. A.; Ashurkov, S. V.; Rasskazov, I. Yu.

2017-05-01

Information on designing a 3D integrated model of the deflected mode (DM) of rock massif near the Strel'tsovka uranium ore field (SUOF) in the southeastern Transbaikal region is presented in the paper. This information is based on the contemporary stresses estimated by geostructural and tectonophysical techniques and by studying the seismotectonic deformation of the Earth's surface using the data on earthquake source mechanisms and GPS geodesy focused on the recognition of active faults. A combination of the results of geostructural, geophysical, geotectonic, and petrophysical research, as well as original maps of faulting and the arrangement of seismic dislocations and seismotectonic regimes (stress tensors), allowed us to design models of the structure, properties, and rheological links of the medium and to determine the boundary conditions for numerical tectonophysical simulation using the method of terminal elements. The computed 2D and 3D models of the state of the rock massif have been integrated into 3D GIS created on the basis of the ArcGIS 10 platform with an ArcGIS 3D-Analyst module. The simulation results have been corroborated by in situ observations on a regional scale (the Klichka seismodislocation, active from the middle Pliocene to date) and on a local scale (heterogeneously strained rock massif at the Antei uranium deposit). The development of a regional geodynamic model of geological structural units makes it possible to carry out procedures to ensure the safety of mining operations under complex geomechanical conditions that can expose the operating mines and mines under construction, by the Argun Mining and Chemical Production Association (PAO PPGKhO) on a common methodical and geoinformational platform, to the hazards of explosions, as well as to use the simulation results aimed at finding new orebodies to assess the flanks and deep levels of the ore field.

Application of the Geo-Anomaly Unit Concept in Quantitative Delineation and Assessment of Gold Ore Targets in Western Shandong Uplift Terrain, Eastern China

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen Yongqing, E-mail: ydonglai@mail.cgs.gov.cn; Zhao Pengda; Chen Jianguo

2001-03-15

A number of large and giant ore deposits have been discovered within the relatively small areas of lithospheric structure anomalies, including various boundary zones of tectonic plates. The regions have become the well-known intercontinental ore-forming belts, such as the circum-Pacific gold-copper, copper-molybdenum, and tungsten-tin metallogenic belts. These belts are typical geological anomalous areas. An investigation into the hydrothermal ore deposits in different regions in the former Soviet Union illustrated that the geologic structures of ore fields of almost all major commercial deposits have distinct features compared with the neighboring areas. These areas with distinct features are defined as geo-anomalies. Amore » geo-anomaly refers to such a geologic body or a combination of bodies that their composition, texture-structure, and genesis are significantly different from those of their surroundings. A geo-anomaly unit (GU) is an area containing distinct features that can be delineated with integrated ore-forming information using computer techniques on the basis of the geo-anomaly concept. Herein, the GU concept is illustrated by a case study of delineating the gold ore targets in the western Shandong uplift terrain, eastern China. It includes: (1) analyses of gold ore-forming factors; (2) compilation of normalized regional geochemical map and extraction of geochemical anomalies; (3) compilation of gravitational and aeromagnetic tectonic skeleton map and extraction of gravitational and aeromagnetic anomalies; (4) extraction of circular and linear anomalies from remote-sensing Landsat TM images; (5) establishment of a geo-anomaly conceptual model associated with known gold mineralization; (6) establishment of gold ore-forming favorability by computing techniques; and (7) delineation and assessment of ore-forming units. The units with high favorability are suggested as ore targets.« less

Geology of the Barite Hill gold-silver deposit in the southern Carolina slate belt

USGS Publications Warehouse

Clark, S.H.B.; Gray, K.J.; Back, J.M.

1999-01-01

Barite Hill is a stratiform gold-silver deposit associated with base metal sulfides and barite in greenschist facies rocks. The deposit, southernmost of four recently mined gold deposits in the Carolina slate belt, is located in the Lincolnton-McCormick district of Georgia and South Carolina, which includes several known gold-silver and base metal deposits in a Kuroko-type geological setting along with deposits of kyanite and manganese. Approximately 1,835,000 g of gold was produced mainly from oxidized ores in the Main and Rainsford pits from 1990 until their closing in 1994. Ore is hosted by sericitically altered felsic metavolcanic and metasedimentary rocks of the Late Proterozoic Persimmon Fork Formation. The deposit is stratigraphically below an overturned contact between upper and lower pyroclastic units, which overlie the Lincolnton metarhyolite, an intrusive unit. Gold-silver-rich zones in the Main pit are partly coincident with lenses of siliceous barite rock, but not confined to them, and occur more commonly in pyrite-quartz-altered fragmental rock. The Main pit ore is stratigraphically overlain by a zone of base metal and barite enrichment, which is, in turn, overlain by a talc-tremolite alteration zone locally. Siliceous barite zones are absent in the Rainsford pit, and gold-silver minerals are associated with silicified rocks and chert. The Barite Hill deposit is interpreted to be the result of Kuroko-type, volcanogenic, base metal sulfide mineralization, followed by gold-silver mineralization under epithermal conditions with the following stages of evolution: (1) massive sulfides, barite, and fine-grained siliceous exhalites were deposited during Late Proterozoic to Cambrian submarine volcanism, which was related to plate convergence and subduction in a microcontinental or island-arc setting distant from the North American continental plate; (2) Au-Ag-Te and base and precious metal Te-Se-Bi minerals were deposited either during waning stages of

Fluid inclusion characteristics and geological significance of the Dajinshan W-Sn polymetallic deposit in Yunfu, Guangdong Province

NASA Astrophysics Data System (ADS)

Yu, Zhangfa; Chen, Maohong; Zhao, Haijie

2015-05-01

The Dajinshan tungsten-tin polymetallic deposit is a quartz-vein-type ore deposit located in Western Guangdong Province. The ore bodies show a fairly simple shape and mainly occur as tungsten-tin polymetallic-bearing sulfide quartz veins, including quartz vein, quartz-greisens, and sulfide quartz veins, and their distribution is spatially related to Dajinshan granitoids. The formation of the deposit experienced three stages: a wolframite-molybdenite-quartz stage, a wolframite-cassiterite-sulfide-quartz stage, and a fluorite-calcite-carbonate stage. Based on detailed petrographic observations, we conducted microthermometric and Raman microspectroscopic studies of fluid inclusions formed at different ore-forming stages in the Dajinshan tungsten-tin polymetallic deposit, identifying four dominant types of fluid inclusions: aqueous two-phase inclusions, CO2-bearing inclusions, solid or daughter mineral-bearing inclusions, and gas-rich inclusions. The gas compositions of ore-forming fluids in the Dajinshan tungsten-tin polymetallic deposit are mostly CO2, CH4, and H2O. The hydrogen, oxygen, and sulfur isotopic data imply that the ore-forming fluids in the Dajinshan tungsten-tin polymetallic deposit were mainly derived from magmatic fluids, mixed with meteoric water in the ore-formation process. These results indicate that the fluid mixing and boiling led to the decomposition of the metal complex in ore-forming fluids and ore deposition.

Regional Crustal Structures and Their Relationship to the Distribution of Ore Deposits in the Western United States, Based on Magnetic and Gravity Data

USGS Publications Warehouse

Hildenbrand, T.G.; Berger, B.; Jachens, R.C.; Ludington, S.

2000-01-01

Upgraded gravity and magnetic databases and associated filtered-anomaly maps of western United States define regional crustal fractures or faults that may have guided the emplacement of plutonic rocks and large metallic ore deposits. Fractures, igneous intrusions, and hydrothermal circulation tend to be localized along boundaries of crustal blocks, with geophysical expressions that are enhanced here by wavelength filtering. In particular, we explore the utility of regional gravity and magnetic data to aid in understanding the distribution of large Mesozoic and Cenozoic ore deposits, primarily epithermal and porphyry precious and base metal deposits and sediment-hosted gold deposits in the western United States cordillera. On the broadest scale, most ore deposits lie within areas characterized by low magnetic properties. The Mesozoic Mother Lodge gold belt displays characteristic geophysical signatures (regional gravity high, regional low-to-moderate background magnetic field anomaly, and long curvilinear magnetic highs) that might serve as an exploration guide. Geophysical lineaments characterize the Idaho-Montana porphyry belt and the La Caridad-Mineral Park belt (from northern Mexico to western Arizona) and thus indicate a deep-seated control for these mineral belts. Large metal accumulations represented by the giant Bingham porphyry copper and the Butte polymetallic vein and porphyry copper systems lie at intersections of several geophysical lineaments. At a more local scale, geophysical data define deep-rooted faults and magmatic zones that correspond to patterns of epithermal precious metal deposits in western and northern Nevada. Of particular interest is an interpreted dense crustal block with a shape that resembles the elliptical deposit pattern partly formed by the Carlin trend and the Battle Mountain-Eureka mineral belt. We support previous studies, which on a local scale, conclude that structural elements work together to localize mineral deposits within

Biogenic non-crystalline U(IV) revealed as major component in uranium ore deposits

USGS Publications Warehouse

Bhattacharyya, Amrita; Campbell, Kate M.; Kelly, Shelly; Roebbert, Yvonne; Weyer, Stefan; Bernier-Latmani, Rizlan; Borch, Thomas

2017-01-01

Historically, it is believed that crystalline uraninite, produced via the abiotic reduction of hexavalent uranium (U(VI)) is the dominant reduced U species formed in low-temperature uranium roll-front ore deposits. Here we show that non-crystalline U(IV) generated through biologically mediated U(VI) reduction is the predominant U(IV) species in an undisturbed U roll-front ore deposit in Wyoming, USA. Characterization of U species revealed that the majority (∼58-89%) of U is bound as U(IV)to C-containing organic functional groups or inorganic carbonate, while uraninite and U(VI) represent only minor components. The uranium deposit exhibited mostly 238U-enriched isotope signatures, consistent with largely biotic reduction of U(VI) to U(IV). This finding implies that biogenic processes are more important to uranium ore genesis than previously understood. The predominance of a relatively labile form of U(IV) also provides an opportunity for a more economical and environmentally benign mining process, as well as the design of more effective post-mining restoration strategies and human health-risk assessment.

Significance of the precambrian basement and late Cretaceous thrust nappes on the location of tertiary ore deposits in the Oquirrh Mountains, Utah

USGS Publications Warehouse

Tooker, Edwin W.

2005-01-01

The Oquirrh Mountains are located in north central Utah, in the easternmost part of the Basin and Range physiographic province, immediately south of the Great Salt Lake. The range consists of a northerly trending alignment of peaks 56 km long. Tooele and Rush Valleys flank the Oquirrh Mountains on the western side and Salt Lake and Cedar Valleys lie on the eastern side. The world class Bingham mine in the central part of the range hosts disseminated copper-bearing porphyry, skarn, base-and precious-metal vein and replacement ore deposits. The district includes the outlying Barneys Canyon disseminated-gold deposits. Disseminated gold in the Mercur mining district in the southern part of the range has become exhausted. The Ophir and Stockton base- and precious-metal mining districts in the range north of Mercur also are inactive. A geologic map of the range (Tooker and Roberts, 1998), available at a scale of 1:50,000, is a summation of U.S. Geological Survey (USGS) studies. Information about the range and its mining areas is scattered. This report summarizes map locations, new stratigraphic and structural data, and reexamined data from an extensive published record. Unresolved controversial geological interpretations are considered, and, for the first time, the complete geological evidence provides a consistent regional basis for the location of the ore deposits in the range. The geological setting and the siting of mineral deposits in the Oquirrh Mountains began with the formation of a Precambrian craton. Exposures of folded Proterozoic basement rocks of the craton, in the Wasatch Mountains east of Salt Lake City, were accreted and folded onto an Archean crystalline rock terrane. The accretion suture lies along the north flank of the Uinta Mountains. The western part of the accreted block was offset to northern Utah along a north-trending fault lying approximately along the Wasatch Front (Nelson and others, 2002), thereby creating a prominant basement barrier or

Geology and Fluorspar Deposits of the Levias-Keystone and Dike-Eaton Areas, Crittenden County, Kentucky

USGS Publications Warehouse

Trace, Robert Denny

1962-01-01

The fault systems of the Levias-Keystone and Dike-Eaton areas, in the Kentucky-Illinois fiuorspar district, are a complex northeastward-trending sys- tem and a simple northwestward-trending system of steeply dipping normal faults, associated in part with a lamprophyre dike. Fluorspar mining started in the area about 1900 and, as of 1945, more than 200,000 tons of crude ore probably has been mined; most of the ore was from the Levias-Keystone area. A small quantity of zinc and lead ore also is present in the Dike-Eaton area. The deposits are localized along faults that displace fiat-lying or low-dipping limestones, sandstones, and shales of the Meramec and Chester series of Missis- sippian age. Movement along most of the faults was principally vertical, with displacement as much as 600 feet. Some horizontal movement occurred along at least one fault. Geologic mapping of the surface and data from underground workings have revealed 13 faults in an area of four-fifths of a square mile. Only a few of these faults are known to contain economically important deposits of fiuorspar. The most abundant vein minerals are calcite and fiuorite with subordinate quantities of sphalerite, galena, barite, and quartz. Some weathering products of sphalerite and galena are present also. The veins are dominantly calcite that contains fiuorite lenses but in places are mainly fiuorite having lesser quantities of calcite. Sphalerite- and galena-bearing deposits are present in the Dike-Eaton area. The ore bodies mainly are the result of fissure filling and replacement of calcite by fiuorite; in addition a small amount of limestone wallrock probably has been replaced. Residual concentrations of high-grade fluorspar in the overburden above faults have yielded some so-called gravel fiuorspar. The position of the veins within the faults may be related to one or more factors such as type of wallrock, change in dip of the fault, and amount of displacement.

Geology and ore deposits of the Mahd Adh Dhahab District, Kingdom of Saudi Arabia

USGS Publications Warehouse

Luce, Robert W.; Bagdady, Abdulaziz; Roberts, Ralph Jackson

1976-01-01

The principal ore minerals are pyrite, chalcopyrite, sphalerite, galena, and minor tetrahedrite, argentite, and native gold and silver. The gold and silver occurs finely disseminated in the veins and in the altered selvages of the veins. Widespread potassic and propylitic alteration accompanied the ore-forming processes. Potassium feldspar was introduced during an early stage of vein formation. Isotopic analyses of lead in vein potassium feldspar and galena yield a model age of about 900-1050 million years with the possibility of the original lead source having been remobilized about 600 million years ago. Chlorite and carbonate are also prominent vein minerals.

Petrographic and Geochemical Characterization of Ore-Bearing Intrusions of the Noril'sk type, Siberia; With Discussion of Their Origin, Including Additional Datasets and Core Logs

USGS Publications Warehouse

Czamanske, Gerald K.

2002-01-01

The Noril'sk I, Talnakh, and Kharaelakh intrusions of the Noril'sk district host one of the outstanding metal concentrations in the world; contained Cu-Ni resources are comparable to the deposits at Sudbury, Ontario and the platinum group element (PGE) resource is second only to that of the Bushveld Complex. Our opportunity to cooperatively sample and study this district in Siberian Russia arose in 1990 through a memorandum of understanding between the U.S. Geological Survey and the former Ministry of Geology of the U.S.S.R. The world-class significance of these deposits and the possibility that understanding their geologic context, including construction of a credible 'ore-deposit model,' will lead to discovery of similar deposits elsewhere, inspired extensive studies of the ores, the mafic-intrusions which host them, and associated flood basalts.

The role of metasomatism in the balance of halogens in ore-forming process at porphyry Cu-Mo deposits

NASA Astrophysics Data System (ADS)

Berzina, A. N.

2009-04-01

Volatile components play an important role in the evolution of ore-magmatic systems and their ore potential. Of special interest are fluorine and chlorine compounds that principally control the transportation of ore elements by the fluid in a magmatic process and under high-temperature hydrothermal conditions. Study of the evolution of fluorine-chlorine activity in the ore-forming process and their source is usually based on analysis of their magmatic history, whereas the additional source of fluorine and chlorine released during metasomatic alteration of rocks hosting mineralization is poorly discussed in the existing literature. Based on microprobe data on Cl and F abundances in halogen-containing minerals (biotite, amphibole, apatite, titanite) in intrusive rocks and their hydrothermally altered varieties, the role of metasomatic processes in the balance of volatiles in the ore-forming system is discussed by the example of porphyry Cu-Mo deposits of Siberia (Russia) and Mongolia. Two groups of the deposits are considered: copper-molybdenum (Erdenetiin Ovoo, Mongolia and Aksug, Russia) with prevailing propylitic and phyllic alteration and molybdenum-copper (Sora, Russia), with predominant potassic alteration. All types of hydrothermal alterations have led to drastic decrease in Cl contents in metasomatic minerals as compared with halogen-containing magmatic minerals. All studied deposits (particularly those where propylitic and phyllic alteration were developed) show a nearly complete chlorine removal from altered halogen-containing rock-forming minerals (biotite and amphibole). The Cl content in amphibole decreases several times at the stage of replacement with actinolite in the process of propylitization. In the later chlorites (ripidolite and brunsvigite) that replace amphibole, actinolite, and biotite, chlorine is not detected by microprobe (detection limit 0.01-0.02% Cl). Chlorine was also not detected in white micas (muscovite-phengite series) in quartz

Fluid evolution and ore genesis of the Dalingshang deposit, Dahutang W-Cu ore field, northern Jiangxi Province, South China

NASA Astrophysics Data System (ADS)

Peng, Ning-Jun; Jiang, Shao-Yong; Xiong, Suo-Fei; Pi, Dao-Hui

2018-02-01

The Dalingshang W-Cu deposit is located in the North section of the Dahutang ore field, northern Jiangxi Province, South China. Vein- and breccia-style tungsten-copper mineralization is genetically associated with Mesozoic S-type granitic rocks. Infrared and conventional microthermometric studies of both gangue and ore minerals show that the homogenization temperatures for primary fluid inclusions in wolframite ( 340 °C) are similar to those in scheelite ( 330 °C), but about 40 °C higher than those of apatite ( 300 °C) and generally 70 °C higher than those in coexisting quartz ( 270 °C). Laser Raman analysis identifies CH4 and N2 without CO2 in fluid inclusions in scheelite and coexisting quartz, while fluid inclusions in quartz of the sulfide stage have variable CO2 content. The ore-forming fluids overall are characterized by high- to medium-temperature, low-salinity, CH4, N2, and/or CO2-bearing aqueous fluids. Chalcopyrite, muscovite, and sphalerite are the most abundant solids recognized in fluid inclusions from different ores. The H-O-S-Pb isotope compositions favor a dominantly magmatic origin for ores and fluids, while some depleted δ34S values (- 14.4 to - 0.9‰) of sulfides from the sulfide stage are most likely produced by an increase of oxygen fugacity, possibly caused by inflow of oxidized meteoric waters. The microthermometric data also indicate that a simple cooling process formed early scheelite and wolframite. However, increasing involvement of meteoric waters and fluid mixing may trigger a successive deposition of base metal sulfides. Fluid-rock interaction was critical for scheelite mineralization as indicated by in-situ LA-ICP-MS analysis of trace elements in scheelite.

Environment of ore deposition in the Creede mining district, San Juan Mountains, Colorado: Part VI. Maximum duration for mineralization of the OH vein

USGS Publications Warehouse

Campbell, W.R.; Barton, P.B.

2005-01-01

The rate at which ore deposits form is one of the least well established parameters in all of economic geology. However, increased detail in sampling, improved technology of dating, and sophistication in modeling are reducing the uncertainties and establishing that ore formation, at least for the porphyry copper-skarn-epithermal base and precious metals deposit package, may take place in surprisingly brief intervals. This contribution applies another approach to examine the duration of mineralization. The degree to which compositional gradients within single crystals has flattened through solid-state diffusion offers a measure of the thermal dose (that is temperature combined with time) that the crystals have been subjected to since deposition. Here we examine the steepness of gradients in iron content within individual single sphalerite crystals from the epithermal silver-lead-zinc deposit in the OH vein at Creede, Colorado. Two initial textures are considered: growth-banded crystals and compositionally contrasting overgrowths that succeed crosscutting dissolution or fractured surfaces. The model used estimates the maximum possible time by assuming a perfectly sharp original compositional step, and it asks how long it would take at a known temperature for the gradient measured today to have formed. Applying the experimentally determined diffusion rates of Mizuta (1988a) to compositional gradients (ranging from 0.4-2.2 mol % FeS/??m) measured by the electron microprobe in 2-??m steps on banded sphalerite formed early in the paragenetic history yields a maximum duration of less than ???10,000 yr. Sphalerite from a solution unconformity in a position midway through the paragenetic sequence is indistinguishable from instantaneous deposition, supporting the conclusion of rapid ore formation. While this formation interval seems very brief, it is consistent with less well constrained estimates using entirely different criteria. ?? 2005 Society of Economic Geologists, Inc.

The formation of ore mineral deposits on the Moon: A feasibility study

NASA Technical Reports Server (NTRS)

Taylor, Lawrence A.; Lu, Fengxiang

1992-01-01

Most of the ore deposits on Earth are the direct result of formation by hydrothermal solutions. Analogous mineral concentrations do not occur on the Moon, however, because of the absence of water. Stratified ore deposits form in layered instrusives on Earth due to fractional crystallization of magma and crystal settling of high-density minerals, particularly chromium in the mineral chromite. We have evaluated the possibility of such mineral deposition on the Moon, based upon considerations of 'particle settling velocities' in lunar vs. terrestrial magmas. A first approximation of Stoke's Law would seem to indicate that the lower lunar gravity (1/6 terrestrial) would result in slower crystal settling on the Moon. However, the viscosity of the silicate melt is the most important factor affecting the settling velocity. The viscosities of typical lunar basaltic melts are 10-100 times less than their terrestrial analogs. These lower viscosities result from two factors: (1) lunar basaltic melts are typically higher in FeO and lower in Al2O3, Na2O, and K2O than terrestrial melts; and (2) lunar igneous melts and phase equilibria tend to be 100-150 C higher than terrestrial, largely because of the general paucity of water and other volatile phases on the Moon. Therefore, particle settling velocities on the Moon are 5-10 times greater than those on Earth. It is highly probable that stratiform ore deposits similar to those on Earth exist on the Moon. The most likely ore minerals involved are chromite, ilmenite, and native FeNi metal. In addition, the greater settling velocities of periodotite in lunar magmas indicate that the buoyancy effects of the melt are less than on Earth. Consequently, the possibility is considerably less than on Earth of deep-seated volcanism transporting upper mantle/lower crustal xenoliths to the surface of the Moon, such as occurs in kimberlites on Earth.

Analytical fingerprint for tantalum ores from African deposits

NASA Astrophysics Data System (ADS)

Melcher, F.; Graupner, T.; Sitnikova, M.; Oberthür, T.; Henjes-Kunst, F.; Gäbler, E.; Rantitsch, G.

2009-04-01

Kibaran age either show flat patterns for most tantalites, rising values from the LREE to the HREE, or trough-like patterns. Eu anomalies are strongly negative in columbite-tantalite from the Alto Ligonha Province in Mozambique, from the Namaqualand Province (Namibia, South Africa), and from Zimbabwe. Four main age populations of coltan deposits in Africa were revealed: (1) Archean (>2.5 Ga), (2) Paleoproterozoic (2.1-1.9 Ga), (3) early Neoproterozoic ("Kibaran", 1.0-0.9 Ga), and (4) late Neoproterozoic to early Paleozoic (Pan-African; ca. 0.6-0.4 Ga). Currently, we focus on the resolution of the fingerprinting system from region via ore province down to deposit scale, establishing a large and high-quality analytical data base, and developing fast-screening and low-cost methods. Analytical flow-charts and identification schemes for coltan ores will be presented at the Conference. The analytical results obtained so far indicate that a certification scheme including fingerprinting of sources of coltan ores is feasible. The methodology developed is capable to assist in the establishment of a control instrument in an envisaged certification of the production and trade chain of coltan.

Krasnotur'insk Skarn copper ore field, Northern Urals: The U-Pb age of ore-controlling diorites and their place in the regional metallogeny

NASA Astrophysics Data System (ADS)

Grabezhev, A. I.; Ronkin, Yu. L.; Puchkov, V. N.; Gerdes, A.; Rovnushkin, M. Yu.

2014-06-01

The Krasnotur'insk skarn copper ore field known from the theoretical works of Academician K.S. Korzhinskii is located in the western part of the Tagil volcanic zone (in the area of the town of Krasnotur'insk). The ore field is composed of layered Devonian (Emsian) volcanosedimentary rocks intruded by small plutons of quartz diorites, diorites, and gabbrodiorites. Widespread pre-ore and intra-ore dikes of similar composition control the abundance of the andradite skarns formed after limestones and the magnetitesulfide and sulfide ore bodies formed after skarns. The LA-ICP-MS U-Pb concordant age of zircon from the quartz diorite of the Vasil'evsko-Moskalevskii pluton calculated by 16 analyses (16 crystals) is 407.7 ± 1.6 Ma (MSWD = 1.5). Taking into account the geological and petrogeochemical similarity of diorites of small plutons and intra-ore dikes, it is assumed that this age corresponds to the period of formation of the ore-magmatic system of the Krasnotur'insk skarn copper ore field. It was probably formed somewhat earlier than the Auerbakh montzonitic pluton and the accompanying skarn magnetite deposits in the south.

Reactive flow models of the Anarraaq Zn-Pb-Ag deposit, Red Dog district, Alaska

USGS Publications Warehouse

Schardt, C.; Garven, G.; Kelley, K.D.; Leach, D.L.

2008-01-01

The Red Dog ore deposit district in the Brooks Range of northern Alaska is host to several high-grade, shale-hosted Zn + Pb deposits. Due to the complex history and deformation of these ore deposits, the geological and hydrological conditions at the time of formation are poorly understood. Using geological observations and fluid inclusion data as constraints, numerical heat and fluid flow simulations of the Anarraaq ore deposit environment and coupled reactive flow simulations of a section of the ore body were conducted to gain more insight into the conditions of ore body formation. Results suggest that the ore body and associated base metal zonation may have formed by the mixing of oxidized, saline, metal-bearing hydrothermal fluids (<200??C) with reducing, HS-rich pore fluids within radiolarite-rich host rocks. Sphalerite and galena concentrations and base metal sulfide distribution are primarily controlled by the nature of the pore fluids, i.e., the extent and duration of the HS- source. Forward modeling results also predict the distribution of pyrite and quartz in agreement with field observations and indicate a reaction front moving from the initial mixing interface into the radiolarite rocks. Heuristic mass calculations suggest that ore grades and base metal accumulation comparable to those found in the field (18% Zn, 5% Pb) are predicted to be reached after about 0.3 My for initial conditions (30 ppm Zn, 3 ppm Pb; 20% deposition efficiency). ?? Springer-Verlag 2008.

A unique ore-placer cluster with high-Hg gold mineralization in the Amur region (Russia)

NASA Astrophysics Data System (ADS)

Stepanov, V. A.; Moyseenko, V. G.; Melnikov, A. V.

2017-02-01

This work presents the geological structure and a description of gold-ore manifestations and gold placers in the Un'ya-Bom ore-placer cluster of the Amur gold-bearing province. The host rocks are Late Paleozoic and Mesozoic black-shale formations. Intrusive formations are rare. The sublatitudinal Un'ya thrust fault, along which Paleozoic sandstones overlap Mesozoic flyschoid deposits, is regarded as an orecontrolling structure. Gold-quartz and low-sulfide ores are confined to quartz-vein zones. Ore minerals are arsenopyrite, scheelite, ferberite, galena, and native gold. Gold-ore manifestations and placers contain high-Hg native gold. The high Hg content in native gold is explained by the occurrence of the eroded frontal part of the gold-ore pipe in the ore cluster, a source of native gold.

A unique ore-placer area of the Amur region with high-Hg gold

NASA Astrophysics Data System (ADS)

Melnikov, A. V.; Stepanov, V. A.; Moiseenko, V. G.

2017-10-01

This work presents the geological structure and a description of the gold-ore occurrences and gold placers of the Un'ya-Bom ore-placer cluster of the Amur gold-bearing province. The host rocks are Late Paleozoic and Mesozoic black shales. Intrusive formations occur rarely. The sublatitudinal Un'ya Thrust is the principal ore-controlling structure. Paleozoic sandstones are thrust over Mesozoic flysch deposits along the Un'ya Thrust. The gold-ore occurrences are represented by quartz-vein zones. The ores are gold-quartz, low-sulfide. Ore minerals are arsenopyrite, scheelite, ferberite, galena, and native gold. High-Hg native gold was revealed in the ore occurrences and placers. The high Hg content in native gold is explained by the presence of the frontal part of the gold-bearing column located within the cluster; the rich placers were formed due to crushing of this column.

Resource potential for commodities in addition to Uranium in sandstone-hosted deposits: Chapter 13

USGS Publications Warehouse

Breit, George N.

2016-01-01

Sandstone-hosted deposits mined primarily for their uranium content also have been a source of vanadium and modest amounts of copper. Processing of these ores has also recovered small amounts of molybdenum, rhenium, rare earth elements, scandium, and selenium. These deposits share a generally common origin, but variations in the source of metals, composition of ore-forming solutions, and geologic history result in complex variability in deposit composition. This heterogeneity is evident regionally within the same host rock, as well as within districts. Future recovery of elements associated with uranium in these deposits will be strongly dependent on mining and ore-processing methods.

Alunite in the Pascua-Lama high-sulfidation deposit: Constraints on alteration and ore deposition using stable isotope geochemistry

USGS Publications Warehouse

Deyell, C.L.; Leonardson, R.; Rye, R.O.; Thompson, J.F.H.; Bissig, T.; Cooke, D.R.

2005-01-01

The Pascua-Lama high-sulfidation system, located in the El Indio-Pascua belt of Chile and Argentina, contains over 16 million ounces (Moz) Au and 585 Moz Ag. The deposit is hosted primarily in granite rocks of Triassic age with mineralization occurring in several discrete Miocene-age phreatomagmatic breccias and related fracture networks. The largest of these areas is Brecha Central, which is dominated by a mineralizing assemblage of alunite-pyrite-enargite and precious metals. Several stages of hydrothermal alteration related to mineralization are recognized, including all types of alunite-bearing advanced argillic assemblages (magmatic-hydrothermal, steam-heated, magmatic steam, and supergene). The occurrence of alunite throughout the paragenesis of this epithermal system is unusual and detailed radiometric, mineralogical, and stable isotope studies provide constraints on the timing and nature of alteration and mineralization of the alunite-pyiite-enargite assemblage in the deposit. Early (preore) alteration occurred prior to ca. 9 Ma and consists of intense silicic and advanced argillic assemblages with peripheral argillic and widespread propylitic zones. Alunite of this stage occurs as fine intergrowths of alunite-quartz ?? kaolinite, dickite, and pyrophyllite that selectively replaced feldspars in the host rock. Stable isotope systematics suggest a magmatic-hydrothermal origin with a dominantly magmatic fluid source. Alunite is coeval with the main stage of Au-Ag-Cu mineralization (alunite-pyrite-enargite assemblage ore), which has been dated at approximately 8.8 Ma. Ore-stage alunite has an isotopic signature similar to preore alunite, and ?? 34Salun-py data indicate depositional temperatures of 245?? to 305??C. The ??D and ?? 18O data exclude significant involvement of meteoric water during mineralization and indicate that the assemblage formed from H2S-dominated magmatic fluids. Thick steam-heated alteration zones are preserved at the highest elevations in

Physical and chemical controls on ore shoots - insights from 3D modeling of an orogenic gold deposit

NASA Astrophysics Data System (ADS)

Vollgger, S. A.; Tomkins, A. G.; Micklethwaite, S.; Cruden, A. R.; Wilson, C. J. L.

2016-12-01

Many ore deposits have irregular grade distributions with localized elongate and well-mineralized rock volumes commonly referred to as ore shoots. The chemical and physical processes that control ore shoot formation are rarely understood, although transient episodes of elevated permeability are thought to be important within the brittle and brittle-ductile crust, due to faulting and fracturing associated with earthquake-aftershock sequences or earthquake swarms. We present data from an orogenic gold deposit in Australia where the bulk of the gold is contained in abundant fine arsenopyrite crystals associated with a fault-vein network within tight upright folds. The deposit-scale fault network is connected to a deeper network of thrust faults (tens of kilometers long). Using 3D implicit modeling of geochemical data, based on radial basis functions, gold grades and gold-arsenic element ratios were interpolated and related to major faults, vein networks and late intrusions. Additionally, downhole bedding measurements were used to model first order (mine-scale) fold structures. The results show that ore shoot plunges are not parallel with mine-scale or regional fold plunges, and that bedding parallel faults related to flexural slip folding play a pivotal role on ore shoot attitudes. 3D fault slip and dilation tendency analysis indicate that fault reactivation and formation of linking faults are associated with large volumes of high-grade ore. We suggest slip events on the large-scale thrust network allowed mineralizing fluids to rapidly migrate over large distances and become supersaturated in elements such as gold, promoting widespread precipitation and high nucleation densities of arsenopyrite upon fluid-rock interaction at trap sites within the deposit.

Geochemical Peculiarities of Galena and Sphalerite from Polymetallic Deposits of the Dal'negorskii Ore Region (Primorsky Krai, Russia)

NASA Astrophysics Data System (ADS)

Rogulina, L. I.; Moiseenko, V. G.; Ponomarchuk, V. A.

2018-04-01

New data on the composition of the major minerals from the skarn and vein polymetallic deposits of the Dal'negorskii ore region are reported. Analysis of galena and sphalerite was carried out by the X-ray fluorescent energy-dispersive method of synchrotron radiation for the first time. It is shown that the minor elements in major minerals of different deposits are typomorphic. Among these elements are Fe, Cu, Ni, Cd, Ag, Sn, and Sb, as well as In in sphalerite and Te in galena. The high concentrations of Ag, Cu, Te, Cd, and In in the extracted minerals indicate the complex character of mineralization. The compositional patterns of ore minerals characterize the sequence of mineral formation from the skarn to vein ores, and the sequence of deposits from the mesothermal to epithermal conditions. This provides geochemical evidence for the stage model of the formation of mineralization in the Dal'negorskii ore region.

Geology and geochemistry of three sedimentary-rock-hosted disseminated gold deposits in Guizhou Province, People's Republic of China

USGS Publications Warehouse

Ashley, R.P.; Cunningham, C.G.; Bostick, N.H.; Dean, W.E.; Chou, I.-Ming

1991-01-01

Five sedimentary-rock-hosted disseminated gold deposits have been discovered since 1980 in southwestern Guizhou Province (PRC). Submicron-sized gold is disseminated in silty carbonate and carbonaceous shale host rocks of Permian and Triassic age. Arsenic, antimony, mercury, and thallium accompany the gold. Associated hydrothermal alteration resulted in decarbonatization of limestone, silicification, and argillization, and depletion of base metals, barium, and many other elements. Organic material occurs in most host rocks and ores. It was apparently devolatilized during a regional heating event that preceded hydrothermal activity, and thus was not mobilized during mineralization, and did not affect gold deposition. The geologic setting of the Guizhou deposits includes many features that are similar to those of sedimentary-rock-hosted deposits of the Great Basin, western United States. The heavy-element suite that accompanies gold is the same, but base metals are even scarcer in the Guizhou deposits than they are in U.S. deposits. The Guizhou deposits discovered to date are smaller than most U.S. deposits and have no known spatially associated igneous rocks. ?? 1991.

A deposit model for Mississippi Valley-Type lead-zinc ores: Chapter A in Mineral deposit models for resource assessment

USGS Publications Warehouse

Leach, David L.; Taylor, Ryan D.; Fey, David L.; Diehl, Sharon F.; Saltus, Richard W.

2010-01-01

This report also describes the geoenvironmental characteristic of MVT deposits. The response of MVT ores in the supergene environment is buffered by their placement in carbonate host rocks which commonly results in near-neutral associated drainage water. The geoenvironmental features and anthropogenic mining effects presented in this report illustrates this important environmental aspect of MVT deposits which separates them from other deposit types (especially coal, VHMS, Cu-porphyry, SEDEX, acid-sulfate polymetallic vein).

[Iron ore, economic geology and networks of experts between Wisconsin and the state of Minas Gerais, 1881-1914].

PubMed

Fischer, Georg

2014-01-01

This article deals with the "discovery" of Brazilian iron ore from two perspectives. The first examines the increasing emphasis of the geosciences and their practical application and global reach since the second half of the nineteenth century. While in Brazil economic geology was integrated step by step into state institutions, at the global level it experienced its moment of triumph with the 11th International Geological Congress in 1910. The second deals with a specific social network with a decisive role in the race for Brazilian iron ore: with transnational experts juggling between the logic of the market and that of the academy. The article reveals the importance of local negotiations in the incorporation of the subsoil of Minas Gerais into the global space of mining.

Evolution of volcanic and tectonic features in caldera settings and their importance in the localization of ore deposits

USGS Publications Warehouse

Rytuba, J.J.

1994-01-01

Many calderas are located along regionally important fault zones that are intermittently active before and after the caldera cycle. In mineralized calderas, the ore deposits are controlled by structures developed during caldera formation and by regional faults which intersect and reactivate the caldera-related structures. The paper discusses the importance of the different stages of caldera formation in connection with the localization of ore deposits. -from Author

Magmatic ore deposits in layered intrusions - Descriptive model for reef-type PGE and contact-type Cu-Ni-PGE deposits

USGS Publications Warehouse

Zientek, Michael L.

2012-01-01

Layered, ultramafic to mafic intrusions are uncommon in the geologic record, but host magmatic ore deposits containing most of the world's economic concentrations of platinum-group elements (PGE) (figs. 1 and 2). These deposits are mined primarily for their platinum, palladium, and rhodium contents (table 1). Magmatic ore deposits are derived from accumulations of crystals of metallic oxides, or immiscible sulfide, or oxide liquids that formed during the cooling and crystallization of magma, typically with mafic to ultramafic compositions. "PGE reefs" are stratabound PGE-enriched lode mineralization in mafic to ultramafic layered intrusions. The term "reef" is derived from Australian and South African literature for this style of mineralization and used to refer to (1) the rock layer that is mineralized and has distinctive texture or mineralogy (Naldrett, 2004), or (2) the PGE-enriched sulfide mineralization that occurs within the rock layer. For example, Viljoen (1999) broadly defined the Merensky Reef as "a mineralized zone within or closely associated with an unconformity surface in the ultramafic cumulate at the base of the Merensky Cyclic Unit." In this report, we will use the term PGE reef to refer to the PGE-enriched mineralization, not the host rock layer. Within a layered igneous intrusion, reef-type mineralization is laterally persistent along strike, extending for the length of the intrusion, typically tens to hundreds of kilometers. However, the mineralized interval is thin, generally centimeters to meters thick, relative to the stratigraphic thickness of layers in an intrusion that vary from hundreds to thousands of meters. PGE-enriched sulfide mineralization is also found near the contacts or margins of layered mafic to ultramafic intrusions (Iljina and Lee, 2005). This contact-type mineralization consists of disseminated to massive concentrations of iron-copper-nickel-PGE-enriched sulfide mineral concentrations in zones that can be tens to hundreds

The late cretaceous Donlin Creek gold deposit, Southwestern Alaska: Controls on epizonal ore formation

USGS Publications Warehouse

Goldfarb, R.J.; Ayuso, R.; Miller, M.L.; Ebert, S.W.; Marsh, E.E.; Petsel, S.A.; Miller, L.D.; Bradley, D.; Johnson, Chad; McClelland, W.

2004-01-01

-10 per mil, with the sulfur derived from diagenetic pyrite and organic matter within ihe flysch basin. A smaller group of ??34S measurements, which shows values as depleted as -27 per mil, suggests a different local sulfur reservoir in the basin for the later hydrothermal episode dominated by stibnite. Initial ENd of -8.7 to -3.1 and 87Sr/86Sr measurements of 0.706 to 0.709 for the ore-hosting dikes also indicate a crustal reservoir for some of the Late Cretaceous magmatism. Overlapping lead isotope data for these intrusive rocks and for sulfide minerals suggest a crustal contribution for the lead in both. Copper- and gold-bearing stockwork veinlets in hornfels occur at Dome, a prospect located at the northern end of the Donlin Creek deposit. These stockworks are cut by the younger auriferous gold veins that define the main Donlin Creek gold mineralization. Highly saline, gas-rich, heterogeneously trapped fluids deposited the stockworks at temperatures approximately 100??C hotter than those of the main gold-forming event at Donlin Creek. The genetic relationship of the Dome prospect to the main Donlin Creek gold resource is equivocal. The epizonal Donlin Creek deposit shows affinities to the gold systems interpreted by various workers as orogenic or intrusion related; it shows important differences from typical epithermal and Carlin-like deposits. The ore-forming fluids were derived by either broad-scale metamorphic devolatilization above rising mantle melts or exsolution from a magma that was dominated by a significant flysch melt component. ??2004 by Economic Geology.

Geology of the Hamm Canyon quadrangle, Colorado

USGS Publications Warehouse

Cater, Fred W.

1953-01-01

The Hamm Canyon quadrangle is on eof eighteen 7 1/2-minute quadrangles covering the principal carnotite-producing area of southwestern Colorado. The geology of these quadrangles was mapped by the U.S. Geological Survey for the Atomic Energy Commission as part of a comprehensive study of carnotite deposits. The rocks exposed in the eighteen quadrangles consist of crystalline rocks of pre-Cambrian age and sedimentary rocks that range in age from late Paleozoic to Quaternary. Over much of the area the sedimentary rocks are flat lying, but in places the rocks are disrupted by high-angle faults, and northwest-trending folds. Conspicuous among the folds are large anticlines having cores of intrusive salt and gypsum. Most of the carnotite deposits are confined to the Salt Wash sandstone member of the Jurassic Morrison formation. Within this sandstone, most of the deposits are spottily distributed through an arcuate zone known as the "Uravan Mineral Belt". Individual deposits range in size from irregular masses containing only a few tons of ore to large, tabular masses containing many thousands of tons. The ore consists largely of sandstone selectively impregnated and in part replaced by uranium and vanadium minerals. Most of the deposits appear to be related to certain sedimentary structures in sandstones of favorable composition.

Geology of the Davis Mesa quadrangle, Colorado

USGS Publications Warehouse

Cater, Fred W.; Bryner, Leonid

1953-01-01

The Davis Mesa quadrangle is one of eighteen 7 1/2-minute quadrangles covering the principal carnotite-producing area of southwestern Colorado. The geology of these quadrangles was mapped by the U.S. Geological Survey for the Atomic Energy Commission as part of a comprehensive study of carnotite deposits. The rocks exposed in the eighteen quadrangles consist of crystalline rocks of pre-Cambrian age and sedimentary rocks that range in age from late Paleozoic to Quaternary. Over much of the area the sedimentary rocks are flat lying, but in places the rocks are disrupted by hih-angle faults, and northwest-trending folds. Conspicuous among the folds are large anticlines having cores of intrusive salt and gypsum. Most of the carnotite deposits are confined to the Salt Wash sandstone member of Jurassic Morrison formation. Within this sandstone, most of the deposits are spottily distributed through an arcuate zone known as "Uruvan Mineral Belt". Individual deposits range in size from irregular masses containing only a few tons of ore to large, tabular masses containing many thousands of tons. The ore consists largely of sandstone selectively impregnated and in part replaced by uranium and vanadium minerals. Most of the deposits appear to be related to certain sedimentary structures in sandstones of favorable composition.

Geology of the Gateway quadrangle, Mesa county Colorado

USGS Publications Warehouse

Cater, Fred W.

1953-01-01

The Gateway quadrangle is one of eighteen 7 1/2-minute quadrangles covering the principal carnotite-producing area of southwestern Colorado. The geology of these quadrangles was mapped by the U.S. Geological Survey for the Atomic Energy Commission as part of a comprehensive study of carnotite deposits. The rocks exposed in the eighteen quadrangles consist of crystalline rocks of pre-Cambrian age and sedimentary rocks that range in age from late Paleozoic to Quaternary. Over much of the area the sedimentary rocks are flat lying, but in places the rocks are disrupted by hih-angle faults, and northwest-trending folds. Conspicuous among the folds are large anticlines having cores of intrusive salt and gypsum. Most of the carnotite deposits are confined to the Salt Wash sandstone member of Jurassic Morrison formation. Within this sandstone, most of the deposits are spottily distributed through an arcuate zone known as "Uruvan Mineral Belt". Individual deposits range in size from irregular masses containing only a few tons of ore to large, tabular masses containing many thousands of tons. The ore consists largely of sandstone selectively impregnated and in part replaced by uranium and vanadium minerals. Most of the deposits appear to be related to certain sedimentary structures in sandstones of favorable composition.

Geology of the Horse Range Mesa quadrangle, Colorado

USGS Publications Warehouse

Cater, Fred W.; Bush, A.L.; Bell, Henry; Withington, C.F.

1953-01-01

The Horse Range Mesa quadrangle is one of eighteen 7 1/2-minute quadrangles covering the principal carnotite-producing area of southwestern Colorado. The geology of the quadrangles was mapped by the U.S. Geological Survey for the Atomic Energy Commission as part of a comprehensive study of carnotite deposits. The rocks exposed in the eighteen quadrangles consist of crystalline rocks of pre-Cambrian age and sedimentary rocks that range in age from late Paleozoic to Quaternary. Over much of the area the sedimentary rocks are flat lying, but in places the rocks are disrupted by high-angle faults, and northwest-trending folds. Conspicuous among the folds are large anticlines having cores of intrusive salt and gypsum. Most of the carnotite deposits are confined to the Salt Wash sandstone member of the Jurassic Morrison formation. Within this sandstone, most of the deposits are spottily distributed through an arcuate zone known as the "Uravan Mineral Belt". Individual deposits range in size from irregular masses containing only a few tons of ore to large, tabular masses containing many thousands of tons. The ore consists largely of sandstone selectively impregnated and in part replaced by uranium and vanadium minerals. Most of the deposits appear to be related to certain sedimentary strictures in sandstones of favorable composition.

Geology of the Uravan quadrangle, Montrose county, Colorado

USGS Publications Warehouse

Cater, Fred W.; Butler, A.P.; McKay, E.J.; Boardman, Robert L.

1954-01-01

The Uravan quadrangle is one of eighteen 7 1/2-minute quadrangles covering the principal carnotite-producing area of the southwestern Colorado. The geology of these quadrangles was mapped by the U.S. Geological Survey for the Atomic Energy Commission as part of a comprehensive study of carnotite deposits. The rocks exposed in the eighteen quadrangles consist of crystalline rocks of pre-Cambrian age and sedimentary rocks that range in age from late Paleozoic to Quaternary. Over much of the area the sedimentary rocks are flat lying, but in places the rocks are disrupted by high-angle faults, and northwest-trending folds. Conspicuous among the folds are large anticlines having cores of intrusive salt and gypsum. Most of the carnotite deposits are confined to the Salt Wash sandstone member of the Jurassic Morrison formation. Within this sandstone, most of the deposits are spottily distributed through an arcuate zone known as the "Uravan Mineral Belt". Individual deposits range in size from irregular masses containing only a few tons of ore to large, tabular masses containing many thousands of tons. The ore consists largely of sandstone selectively impregnated and in part replaced by uranium and vanadium minerals. Most of the deposits appear to the related to certain sedimentary structures in sandstones of favorable composition.

Genesis of Silica-Carbonate Type Mercury Ore Deposits in Coast Range California from Mantle Derived Fluids

NASA Astrophysics Data System (ADS)

Rytuba, J. J.; Kirby, S. H.; Kellner, C. R.

2016-12-01

In the Coast Range of California 51 major mercury (Hg) deposits and numerous smaller Hg occurrences began forming when subduction transitioned to the transpressive continental-transform kinematics of the San Andreas Fault System. The Hg deposits become progressively younger to the north reflecting the change in tectonic environment as the Mendocino Triple Junction moved 400 km northward since the Miocene to its present location in northern California. The silica-carbonate mercury deposits are vein and replacement ore bodies developed within and adjacent to serpentinite that was emplaced along regional faults and altered to an assemblage of silica and carbonate minerals. The initial alteration process consists of the addition of carbonate to the serpentinite followed by introduction of silica into the central core. The peripheral zone of calcite-dolomite veining may extend for several kilometers outward from a mercury deposit. The large Hg deposits formed in structural traps, such as antiformal structures, and the ores locally extend into adjacent clastic metasedimentary rocks. The mineralogy of the primary ores is simple consisting of cinnabar, metacinnabar and elemental Hg. The deposits formed from low-temperature, <120oC, CO2-CH4-H2S-rich fluids. The hydrothermal fluids are consistent with a mantle source water derived from the former forearc during subduction and after the transition to transpressive continental-transform boundary as proposed by Kirby et al. (EPS, 2014). Some of the silica-carbonate Hg deposits are overprinted by younger hot spring type Hg mineralization associated temporally with volcanic vents. These Hg deposits have distinctly different types of alteration and geochemistry and formed in the near surface from meteoric waters.

Isotopic composition of Pb in ore deposits of the Betic Cordillera, Spain; origin and relationship to other European deposits

USGS Publications Warehouse

Arribas , Antonio; Tosdal, Richard M.

1994-01-01

The Betic Cordillera in southern Spain is a complex Alpine fold belt that resulted from the Cretaceous through Cenozoic collision of Africa with Europe. The region is illustrative of one of the characteristics of the Alpine-Mediterranean orogen: the occurrence over a limited area of mineral deposits with a wide variety of host rocks, mineralization ages, and styles. The metamorphic basement in the Betic zone is characterized by a nappe structure of superimposed tectonostratigraphic units and consists of lower Paleozoic to Lower Triassic clastic metasedimentary rocks. This is overlain by Middle to Upper Triassic platform carbonate rocks with abundant strata-bound F-Pb-Zn-(Ba) deposits (e.g., Sierra de Gador, Sierra Alhamilla). Cretaceous to Paleogene subduction-related compression in southeastern Spain was followed by Miocene postcollisional extension and resulted in the formation of the Almeria-Cartagena volcanic belt and widespread hydrothermal activity and associated polymetallic mineralization. Typical Miocene hydrothermal deposits include volcanic-hosted Au (e.g., Rodalquilar) and Ag-rich base metal (e.g., Cabo de Gata, Mazarron) deposits as well as complex polymetallic veins, mantos, and irregular replacement bodies which are hosted by Paleozoic and Mesozoic metamorphic rocks and Neogene sedimentary and volcanic rocks (e.g., Cartagena, Sierra Almagrera, Sierra del Aguilon, Loma de Bas).Lead isotope compositions were measured on sulfide samples from nine ore districts and from representative fresh samples of volcanic and basement rock types of the region. The results have been used to evaluate ore-forming processes in southeastern Spain with emphasis on the sources of metals. During a Late Triassic mineralizing event, Pb was leached from Paleozoic clastic metasedimentary rocks and incorporated in galena in strata-bound F-Pb-Zn-(Ba) deposits ( 206 Pb/ 204 Pb = 18.332 + or - 12, 207Pb/ 204 Pb = 15.672 + or - 12, 208 Pb/ 204 Pb = 38.523 + or - 46). The second

Hydrothermal ore-forming processes in the light of studies in rock- buffered systems: II. Some general geologic applications

USGS Publications Warehouse

Hemley, J.J.; Hunt, J.P.

1992-01-01

The experimental metal solubilities for rock-buffered hydrothermal systems provide important insights into the acquisition, transport, and deposition of metals in real hydrothermal systems that produced base metal ore deposits. Water-rock reactions that determine pH, together with total chloride and changes in temperature and fluid pressure, play significant roles in controlling the solubility of metals and determining where metals are fixed to form ore deposits. Deposition of metals in hydrothermal systems occurs where changes such as cooling, pH increase due to rock alteration, boiling, or fluid mixing cause the aqueous metal concentration to exceed saturation. Metal zoning results from deposition occurring at successive saturation surfaces. Zoning is not a reflection simply of relative solubility but of the manner of intersection of transport concentration paths with those surfaces. Saturation surfaces will tend to migrate outward and inward in prograde and retrograde time, respectively, controlled by either temperature or chemical variables. -from Authors

Contrasting hydrological processes of meteoric water incursion during magmatic-hydrothermal ore deposition: An oxygen isotope study by ion microprobe

NASA Astrophysics Data System (ADS)

Fekete, Szandra; Weis, Philipp; Driesner, Thomas; Bouvier, Anne-Sophie; Baumgartner, Lukas; Heinrich, Christoph A.

2016-10-01

Meteoric water convection has long been recognized as an efficient means to cool magmatic intrusions in the Earth's upper crust. This interplay between magmatic and hydrothermal activity thus exerts a primary control on the structure and evolution of volcanic, geothermal and ore-forming systems. Incursion of meteoric water into magmatic-hydrothermal systems has been linked to tin ore deposition in granitic plutons. In contrast, evidence from porphyry copper ore deposits suggests that crystallizing subvolcanic magma bodies are only affected by meteoric water incursion in peripheral zones and during late post-ore stages. We apply high-resolution secondary ion mass spectrometry (SIMS) to analyze oxygen isotope ratios of individual growth zones in vein quartz crystals, imaged by cathodo-luminescence microscopy (SEM-CL). Existing microthermometric information from fluid inclusions enables calculation of the oxygen isotope composition of the fluid from which the quartz precipitated, constraining the relative timing of meteoric water input into these two different settings. Our results confirm that incursion of meteoric water directly contributes to cooling of shallow granitic plutons and plays a key role in concurrent tin mineralization. By contrast, data from two porphyry copper deposits suggest that downward circulating meteoric water is counteracted by up-flowing hot magmatic fluids. Our data show that porphyry copper ore deposition occurs close to a magmatic-meteoric water interface, rather than in a purely magmatic fluid plume, confirming recent hydrological modeling. On a larger scale, the expulsion of magmatic fluids against the meteoric water interface can shield plutons from rapid convective cooling, which may aid the build-up of large magma chambers required for porphyry copper ore formation.

Some concepts of favorability for world-class-type uranium deposits in the northeastern United States

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adler, H.H.

1981-03-01

An account is given of concepts of favorability of geologic environments in the eastern United States for uranium deposits of several major types existing elsewhere in the world. The purpose is to convey some initial ideas about the interrelationships of the geology of the eastern United States and the geologic settings of certain of these world-class deposits. The study and report include consideration of uranium deposits other than those generally manifesting the geologic, geochemical and genetic characteristics associated with the conventional sandstone-type ores of the western United States.

Mineralogy and ore fluid chemistry of the Roc Blanc Ag deposit, Jebilet Hercynian massif, Morocco

NASA Astrophysics Data System (ADS)

Essarraj, Samira; Boiron, Marie-Christine; Cathelineau, Michel; Tarantola, Alexandre; Leisen, Mathieu; Hibti, Mohamed

2017-03-01

The Roc Blanc Ag deposit is located about 20 km north of Marrakesh city (Morocco) in the Jebilet Hercynian massif. The ore bodies consist of N-S to NE-SW quartz (±carbonates) veins hosted by the Sarhlef marine sediments. These series, deposited in a Devonian-Carboniferous rift basin context, were deformed during the Hercynian orogeny, and submitted to low-grade regional metamorphism. Two major stages of fluid circulation and metal deposition are distinguished on the basis of mineralogical and paleo-fluid studies carried out on quartz and dolomite (microthermometry, Raman spectroscopy, LA-ICP-MS on individual inclusions, and O, H stable isotope data): (i) an early Fe-As stage, characterized by the circulation of metamorphic aqueous-carbonic fluids, under P-T conditions lower than 200 MPa ± 20 MPa and 400 °C respectively, along N-S structures; (ii) the ore stage, characterized by the circulation of a Na-Mg-K ± Ca high salinity brine, poor in gas but rich in metals such as Fe, Sr, Ba, Zn, Pb, ± Cu (salinity ranging from 19.6 wt% to likely more than 30 wt% NaCl equiv.) and the deposition of a sphalerite/dolomite-calcite assemblage; such a fluid likely evolved to a Na-K-(Ca-Mg)-Ag brine, with significant Pb and Sb concentrations and lower Sr, Ba and Zn concentrations than in the preceding fluid (salinity up to 19.4 wt% NaCl equiv.). The Ag content of the second mineralizing brine ranges from 0.9 mmol/kg to 9.4 mmol/kg solution (100 ppm-1000 ppm), whereas the base metal brine is generally Ag poor (up to 1.3 mmol/kg solution: 140 ppm). Dilution of the Ag brine by low salinity fluids (<6 wt% NaCl equiv., and Th from 130° to 230 °C) seems to be the main driving mechanism for the Ag ore deposition at Roc Blanc, with a possible involvement of cooling and reduction reactions in black schists. Base metal and Ag fluids may have circulated at average temperatures around 200 ± 30 °C or slightly higher and under hydrostatic pressures, along dominant E-W structures. The ore

Four magnetite generations in the Precambrian Varena Iron Ore deposit, SE Lithuania, as a result of rock-fluid interactions

NASA Astrophysics Data System (ADS)

Skridlaite, Grazina; Prusinskiene, Sabina; Siliauskas, Laurynas

2017-04-01

Iron ores in Precambrian crystalline basement of the Varena area, SE Lithuania, were discovered during the detail geological-geophysical exploration in 1982-1992. They are covered with 210-500 m thick sediments. The Varena Iron Ore deposit (VIOD) may yield from 71 to 219.6 million tons of iron ore according to different economic evaluations (Marfin, 1996). They were assumed to be of metasomatic and hydrothermal origin, however several other hypotheses explaining the VIOZ origin, e.g. as a layered mafic or carbonatite intrusions were also suggested. Magnetites of the VIOD were thoroughly investigated by the Cameca SX100 microprobe at the Warsaw University and by the Quanta 250 Energy Dispersive Spectroscopy (EDS) at the Nature Research Centre in Vilnius, Lithuania. Four generations of magnetite were distinguished in the studied serpentine-magnetite ores (D8 drilling) and were compared with the earlier studied and reference magnetites. The earliest, spinel inclusion-rich magnetite cores (Mag-1) have the highest trace element contents (in wt%): Si (0.032), Al (0.167-0.248), Mg (0.340-0.405), Ti (0.215-0.254), V (0.090-0.138) etc. They might have formed during an early metamorphism and/or related skarn formation. Voluminous second magnetite (Mag-2) replacing olivine, pyroxenes, spinel and other skarn minerals at c. 540o C (Magnetite-Ilmenite geothermometer) has much lower trace element abundances, probably washed out by hydrothermal fluids. The latest magnetites (Mag-3 and Mag-4) overgrow the earlier ones and occur near or within the sulfide veins (Mag-4). As was observed from microtextures, the Mag-3 and Mag-4 have originated from the late thermal reworking by dissolution-reprecipitation processes. To imply an origin of the studied magnetites, they were compared to the earlier studied magmatic-metamorphic (1058 drilling), presumably skarn (982 drilling) magnetites from the studied area and plotted in the major magnetite ore type fields according to Dupuis and Beaudoin

Geology of the Naturita NW quadrangle, Colorado

USGS Publications Warehouse

Cater, Fred W.; Vogel, J.D.

1953-01-01

The Naturita NW quadrangle is one of eighteen 7 1/2-minute quadrangles covering the principal carnotite-producing area of southwestern Colorado. The geology of these quadrangles were mapped by the U.S. Geological Survey on behalf of the U.S. Atomic Energy Commission as part of a comprehensive study of carnotite deposits. The rocks exposed in the eighteen quadrangles consist of crystalline rocks of pre-Cambrian age and sedimentary rocks that range in age from late Paleozoic to Quaternary. Over much of the area the sedimentary rocks are flat lying, but in places the rocks are disrupted by high-angle faults, and northwest-trending folds. Conspicuous among the folds are large anticlines having cores of intrusive salt and gypsum. Most of the carnotite deposits are confined to the Salt Wash sandstone member of the Jurassic Morrison formation. Within this sandstone, most of the deposits are spottily distributed through an arcuate zone known as the "Uravan Mineral Belt". Individual deposits range in size from irregular masses containing only a few tons of ore to large, tabular masses containing many thousands of tons. The ore consists largely of sandstone selectively impregnated and in part replaced by uranium and vanadium minerals. Most of the deposits appear ro be related to certain sedimentary structures in sandstones of favorable composition.

Sediment-hosted Pb-Zn Deposits: a global perspective

USGS Publications Warehouse

Leach, David L.; Sangster, Donald F.; Kelley, Karen D.; Large, R; Garven, G.; Allen, Craig R.

2005-01-01

Sediment-hosted Pb-Zn deposits contain the world's greatest lead and zinc resources and dominate world production of these metals. They are a chverse group of ore deposits hosted by a wide variety of carbonate and siliciclastic roch that have no obviolls genetic association with igneous activity. A nmge of ore-fortl1ing processes in a vmiety of geologic and tectonic environments created these deposits over at least two billion years of Earth history. The metals were precipitated by basinal brines in synsedimentary and early diagenetic to low-grade metamorphic environments. The deposits display a broad range of relationships to enclosing host rocks that includes stratiform, strata-bound, and discordant ores. These ores are divided into two broad subt)1Jes: Mississippi Valley-type (MVT) and sedimentmy exhalative (SEDEX), Despite the "exhalative" component inherent in the term "SEDEX," in this manusclipt, direct evidence of an exhalite in the ore or alteration component is not essential for a deposit to be classified as SEDEX. The presence of laminated sulfides parallel to bedding is assumed to be permissive evidence for exhalative ores. The chstinction between some SEDEX and MVT depOSits can be quite subjective because some SEDEX ores replaced carbonate, whereas some MVT depOSits formed in an early diagenetic environment and display laminated ore textures. Geologic and resource information are presented for 248 depositS that provide a framework to describe ,mel compare these deposits. Nine of tlle 10 largest sediment-hosted Pb-Zn deposits are SEDEX, Of the deposits that contain at least 2.5 million metric tons (Mt), there are 35 SEDEX (excluding Broken Hill-type) deposits and 15 MVT (excluding Iris-type) deposits. Despite the skewed distribution of the deposit size, the two deposits types have an excellent correlation between total tonnage and tonnage of contained metal (Pb + Zn), with a fairly consistent ratio of about lO/l, regardless of the size of the deposit or

Petrogenesis of Ore-Bearing and Ore-Barren Intermediate-Acid Intrusive Rocks from Jilongshan Au-Cu Skarn Deposit , the Middle-Lower Yangtze River Metallogenic Belt, Eastern China and their Geological Implications

NASA Astrophysics Data System (ADS)

Zhan, X.; Wei, J.; Chen, M.; Zhao, X.

2017-12-01

Jilongshan Au-Cu skarn deposit in Edong-Jiurui ore district , Middle-Lower Yangtze River Metallogenic Belt(MLYRB) , eastern China ,contains 44 t gold and 32 Mt of copper ores. The mineralization is dominated by massive skarn ores, most of which occurs along the contact zone between the lower Triassic dolomitic limestones and Jilongshan granodioritic intrusion. However, Baiguoshu pluton, no more than 1 km western, has been not found any mineralized occurrence with the same strata. The ore-bearing and ore-barren intrusive rocks are granodiorite porphyries, could not be identified by petrographic characters. Besides, Zircon U-Pb dating results demonstrate that Jilongshan and Baiguoshu intrusion emplaced at 140 ± 1Ma and 141 ± 1 Ma respectively, coeval with the Early Cretaceous magmatism in Edong-Jiurui area. Elements geochemistry present that they are both characterized by high Al2O3, rich Na2O (Na2O/K2O>1.0), enrichment of LILE (Rb, Ba, K, Sr) and depletion of HFSE (Nb, Ta), and weak negative Eu anomalies, which suggest they may be originated from partial melting of enriched mantle and associated with crust-mantle interaction ,evidenced by the Sr-Nd-Hf isotopic composition as well. Although the two are partly geochemically similar with each other, they have some obvious differences. The former have higher K2O and Y, Yb ,lower MgO, and Cr, Ni contents, and more obvious differentiation degree between light and heavy REEs with (La/Yb)N=10.55-15.95 than the latter with (La/Yb)N=8.67-10.47. It is indicated that the magmas of the Jilongshan intrusive rocks were probably derived from deeper source than that of the Baiguoshu, also supported by mineralogical data of biotite. In addition, Jilongshan intrusive rocks have a relatively higher initial Nd (ɛNd (t) = -8.2 - -9.4) and Sr ((87Sr/86Sr)i=0.70822-0.70897) isotopic composition than Baiguoshu (-9.2 - -9.7 and 0.70855-0.70881), as same as Lu-Hf isotopic composition. Therefore, combined with previous studies, we suggest

General geology and mines of the East Tintic mining district, Utah and Juab counties, Utah, with sections on the geology of the Burgin mine and the geology of the Trixie mine

USGS Publications Warehouse

Morris, H.T.; Lovering, Thomas Seward; Mogensen, A.P.; Shepard, W.M.; Perry, L.I.; Smith, S.M.

1979-01-01

This report is a study of the rocks, geologic structures, and mines of a highly productive silver, gold, and base-metal mining district in the east-central Great Basin. The East Tintic mining district is in the east-central part of the East Tintic Mountains, near the east margin of the Basin and Range province in Utah and Juab Counties, Utah. The district occupies the northeastern part of the Eureka quadrangle and is about 5 mi (8 km) wide and 6 mi (9.7 km) long. Officially it is within the designated boundaries of the Tintic mining district, but it generally though erroneously has been regarded as a separate district since the late 1800's.Prospecting was first undertaken in East Tintic in 1870; although small quantities of ore were produced in 1899 and from 1909 to 1913, the district first achieved prominence in 1916 with the discovery of the totally concealed Central ore body of the Tintic Standard mine. Within a few years of this discovery, the Tintic Standard became one of the most productive silver mines in the world. Additional discoveries of important concealed ore deposits have continued to be made in the district, including the North Lily mine in 1927, the Eureka Lilly and Eureka Standard mines in 1928, the Burgin mine in 1958, and the Trixie mine in 1969.To December 31, 1975, the East Tintic mining district has yielded approximately 4.83 million short tons (4.38 million tonnes) of silver, gold, and base-metal ores, largely from concealed deposits overlain by many hundreds of feet of barren rocks. These ores have a gross valuation of approximately $231 million. The district first achieved prominence in 1916 with the discovery of the ore bodies of the Tintic Standard mine, which for a time was the world's richest silver producer (Lindgren, 1933, p. 588). By 1946 this deposit and a number of other deposits discovered and developed nearby had been exhausted, and the district became dormant. A dramatic revival of, mining activities in the East Tintic district

Lead and zinc dust depositions from ore trains characterised using lead isotopic compositions.

PubMed

Kristensen, L J; Taylor, M P; Morrison, A L

2015-03-01

This study investigates an unusual source of environmental lead contamination - the emission and deposition of lead and zinc concentrates along train lines into and out of Australia's oldest silver-lead-zinc mine at Broken Hill, Australia. Transport of lead and zinc ore concentrates from the Broken Hill mines has occurred for more than 125 years, during which time the majority was moved in uncovered rail wagons. A significant amount of ore was lost to the adjoining environments, resulting in soil immediately adjacent to train lines elevated with concentrations of lead (695 mg kg(-1)) and zinc (2230 mg kg(-1)). Concentrations of lead and zinc decreased away from the train line and also with depth shown in soil profiles. Lead isotopic compositions demonstrated the soil lead contained Broken Hill ore in increasing percentages closer to the train line, with up to 97% apportioned to the mined Broken Hill ore body. SEM examination showed ceiling dusts collected from houses along the train line were composed of unweathered galena particles, characteristic of the concentrate transported in the rail wagons. The loss of ore from the uncovered wagons has significantly extended the environmental footprint of contamination from local mining operations over an area extending hundreds of kilometres along each of the three train lines.

Geology of the Pine Mountain quadrangle, Mesa county, Colorado

USGS Publications Warehouse

Cater, Fred W.

1953-01-01

The Pine Mountain quadrangle is one of eighteen 7 1/2-minute quadrangles covering the principal carnotite-producing area of southwestern Colorado. The geology of these quadrangles was mapped by the U.S. Geological Survey for the Atomic Energy Commission as part of a comprehensive study of carnotite deposits. The rocks exposed in the eighteen quadrangles consist of crystalline rocks of pre-Cambrian age and sedimentary rocks that range in age from Paleozoic to Quaternary. Over mush of the area the sedimentary rocks are flat lying, but in places the rocks are disrupted by high-angle faults, and northwest-trending folds. Conspicuous among the folds are large anticlines having cores of intrusive salt and gypsum. Most of the carnotite deposits are confines to the Salt Wash sandstone member of the Jurassic Morrison formation. Within this sandstone, most of the deposits are spottily distributed through an arcuate zone known as the "Uravan Mineral Belt". Individual deposits range in sizer from irregular masses containing only a few ton of ore to large, tabular masses containing many thousands of tons. The ore consists largely of sandstone selectively impregnated and in part replaced by uranium and vanadium minerals. Most of the deposits appear to be related to certain sedimentary structures in sandstones of favorable composition.

Geology of the Calamity Mesa quadrangle, Mesa county, Colorado

USGS Publications Warehouse

Cater, Fred W.; Stager, Harold K.

1953-01-01

The Calamity Mesa quadrangle is one of eighteen 7 1/2-minute quadrangles covering the principal carnotite-producing area of southwestern Colorado. The geology of these quadrangles was mapped by the U.S. Geological Survey for the Atomic Energy Commission as part of a comprehensive study of carnotite deposits. The rocks exposed in the eighteen quadrangles consist of crystalline rocks of pre-Cambrian age and sedimentary rocks the range in age from late Paleozoic to Quaternary. Over much of the area the sedimentary rocks are flat lying, but in places the rocks are disrupted by high-angle faults, and northwest-trending folds. Conspicuous among the folds are large anticlines having cores of intrusive salt and gypsum. Most of the carnotite deposits are confined to the Salt Wash sandstone member of the Jurassic Morrison formation. Within this sandstone, most of the deposits are spottily distributed through an arcuate zone known as the "Uravan Mineral Belt". Individual deposits range in size from irregular masses containing only a few tons of ore to large tabular masses containing many thousands of tons. The ore consists largely of sandstone selectively impregnated and in part replaced by uranium and vanadium minerals. Most of the deposits appear to be related to certain sedimentary structures in sandstones of favorable composition.

Paragenetic and minor- and trace-element studies of Mississippi Valley-type ore deposits of the Silesian-Cracow district, Poland

USGS Publications Warehouse

Viets, J.G.; Leach, D.L.; Lichte, F.E.; Hopkins, R.T.; Gent, C.A.; Powell, J.W.

1996-01-01

Paragenetic and minor- and trace-element studies were conducted on samples of epigenetic ore and gangue minerals collected from mines and drill core in the Silesian-Cracow (S-C) district of southern Poland. Four discrete mineral suites representing four mineralizing stages can be identified throughout the district. The earliest epigenetic minerals deposited during stage 1 consist of a late dolomite cement together with minor pyrite and marcasite. Stage 2 was the first ore-forming stage and included repetitive deposition of sphalerite and galena in a variety of morphologies. Stage 3 abruptly followed the first ore stage and deposited marcasite and pyrite with variable amounts of late sphalerite and galena. In the samples studied, minerals deposited during stage 3 are predominately marcasite-pyrite with minor sphalerite and galena in the Pomorzany and Olkusz mines, whereas, at the Trzebionka mine, stage 3 mineralization deposited mostly galena and sphalerite with little marcasite or pyrite. Stage 4 minerals include contains barite, followed by calcite, with very minor pyrite and a rare, late granular sphalerite. Compared to other major Mississippi Valley-type (MVT) districts of the world, the Silesian-Cracow district contains sphalerite with the second largest range in Ag concentrations and the largest range in Fe and Cd concentrations of any district. Unlike in other districts, very wide ranges in minor- and trace-element concentrations are also observed in paragenetically equivalent samples collected throughout the district. This wide range indicates that the minor- and trace-element content of the ore-forming environment was highly variable, both spatially and temporally, and suggests that the hydrologic system that the ore fluids traversed from their basinal source was very complex. Throughout the district, a significant increase in Tl, Ge, and As concentrations is accompanied by a lightening of sulfur isotopes between stage 2 and stage 3 minerals. This change

Testing ore deposit models using in situ U-Pb geochronology of hydrothermal monazite: Paleoproterozoic gold mineralization in northern Australia

NASA Astrophysics Data System (ADS)

Rasmussen, Birger; Sheppard, Stephen; Fletcher, Ian R.

2006-02-01

The inability to establish absolute ages for gold deposition in the Pine Creek orogen of northern Australia has led to conflicting ore deposit models, ranging from intrusion related, which predict that gold mineralization was synchronous with granite magmatism (ca. 1835 1820 Ma), to orogenic, which place ore deposition nearly 100 m.y. later. Here we present ion microprobe U-Pb geochronology for a mineralized quartz reef from Tom's Gully mine, Mount Bundey, Northern Territory, Australia, and nearby granitic rocks and associated contact aureoles. Isotopic dating of zircon and monazite indicates that intrusion and contact metamorphism occurred ca. 1825 Ma, whereas hydrothermal monazite from the auriferous quartz reef gives a mean 207Pb/206Pb age of 1780 ± 10 Ma, interpreted as the time of gold mineralization. Mineralization therefore postdated intrusion by ˜45 m.y. and preceded a postulated ca. 1740 1730 Ma cratonwide orogenic gold event by ˜50 m.y. Hence, neither the intrusion-related model nor the recently proposed orogenic model is applicable. Combined with a reevaluation of age data from the nearby Goodall gold deposit, our data suggest that mineralization coincides with, and may be related to, an episode of regional low-grade metamorphism, deformation, and fluid circulation (Shoobridge event). Our results demonstrate the importance of high-precision in situ geochronology and detailed petrography for deciphering age relationships in ore deposits, and of testing the veracity of models for ore formation.

Late Miocene Debris-Avalanche Deposit At The Gutai Shield Volcano, NW Romania. Re- Evaluation Of Geological Mapping And Mineral Deposits

NASA Astrophysics Data System (ADS)

Seghedi, I.; Fülöp, A.

2009-05-01

The recent identification of debris avalanche deposits (DADs) originating from the southern edge of the Ignis peak (1306m, highest of the Gutai Mts.) has important implications for understanding its genesis in the geological context of the broader area, rich in hydrothermal intrusive-related base metal and gold-silver deposits closely connected to the Dragos Voda - Bogdan Voda strike-slip fault system. Pyroxene andesite lavas are exposed below the Ignis peak followed by hornblende and pyroxene andesites the only ones found in the DAD. The flank failure event has left an E-W-oriented horseshoe shaped scar with an estimated volume of material removed of at least 0.35 km3 and an estimated area covered by DADs of 4,345 km2 as a minimum. The deposit is a mega breccia with a variable amount of coarse matrix with jigsaw-fractured blocks, large boulders, and several southward-elongated hummocks up to 1.8 km distance from the scar. Between 720-850 m altitude the DADs contain megablocks of 5-12 m thick and up to 100 m long of layered fine-grained poorly consolidated pyroclastic materials of interlayered ash and lapillistone of fallout origin, and clay beds rich in vegetation remnants(known as the 'Chiuzbaia flora' of similar age as the surrounding lava flows, i.e. ca. 10-7 Ma) and diatoms. These megablocks found in various positions, suggest a lithological discontinuity likely representing the detachment surface of the gravity-driven instability phenomenon and the deep excavation of the volcano flank by the sector collapse event. The clayey material of these blocks acted probably as an efficient barrier to water infiltration and helped destabilization of the overlying rock mass. Since no explosive products have been observed to follow the DAD, it is possible that the sliding was triggered by pressure release of hydrothermal system along an E-W fault parallel to the Dragos Voda-Bogdan Voda fault system, with related high-grade ore deposits. This suggests the possible presence

Geology and mineral deposits of the Minnie Moore and Bullion mineralized areas, Blaine County, Idaho

USGS Publications Warehouse

Link, Paul Karl; Worl, Ronald G.

2001-01-01

In the early 1880?s the discovery of rich ores in the Minnie Moore and Bullion mineralized areas sparked a rush to settle and develop the Wood River valley. Silver and lead discoveries in these areas spurred the boom in mining after completion of the Oregon Short Line Railroad to Hailey in 1883. In both areas the ore comprises galena, sphalerite, and tetrahedrite in a gangue of siderite, calcite, or quartz. Minor goldbearing quartz veins are also present. The ore is in fissure and replacement veins along fracture systems that formed in Late Cretaceous time, after intrusion of nearby granodiorite or quartz diorite stocks. The ore formed under mesothermal conditions and heat was supplied by the nearby plutons. In the Minnie Moore area, the mineralized veins are cut by low-angle normal faults that are of probable Eocene age. In the Minnie Moore mineralized area, the host rock is the middle part of the Devonian Milligen Formation, (the informal Lucky Coin limestone and Triumph argillite), which is the same stratigraphic level as the host ore in the rich Triumph mine northeast of Hailey. In the Bullion mineralized area, the ore is hosted by the lower member of the Middle Pennsylvanian to Lower Permian Dollarhide Formation. Rich ore was mined in several tunnels that reached the Mayflower vein, a northwest-striking mineralized shear zone. The deposits are thought to be mainly mesothermal veins that formed in association with Cretaceous magmatism. The syngenetic stratiform model of ore formation has often been applied to these deposits, however, no evidence of syngenetic mineralization was found in this study. Faulting has displaced most of the major orebodies and thus has made mining these deposits a challenge.

The geology, mineralogy and paragenesis of the Castrovirreyna lead-zinc-silver deposits, Peru

USGS Publications Warehouse

Lewis, Richard Wheatley

1964-01-01

The Castrovirreyna mining district lies in the Andean Cordillera of South Central Peru, and has been worked sporadically since its discovery in 1591. Supergene silver ores were first mined. Currently the district produces about 20,000 tons of lead-zinc ore and 5000 tons of silver ore annually. The district is underlain by Tertiary andesitic rocks interbedded with basalts and intruded by small bodies of quartz latite porphyry. The terrane reflects recent glaciation and is largely covered by glacial debris. The ore deposits are steeply dipping veins that strike N. 60? E. to S. 50? E., and average 60 centimeters wide and 300 meters long. The principal veins are grouped around three centers, lying 5 kilometers apart along a line striking N. 55? E. They are, from east to west: San Genaro, Caudalosa, and La Virreyna. A less important set of veins, similarly aligned, lies 2 kilometers to the north. Most of the veins were worked to depths of about 30 meters, the limit of supergene enrichment; but in the larger veins hypogene ores have been worked to depths of over 150 meters. Galena, sphalerite, chalcopyrite, and tetrahedrite are common to all veins, but are most abundant in the westernmost veins at La Virreyna. In the center of the district, around Caudalosa, land sulfantimonides are the commonest ore minerals, and at the eastern end, around San Genaro and Astohuaraca, silver sulfosalts predominate. Supergene enrichment of silver is found at shallow depths in all deposits. Silver at San Genaro, however, was concentrated towards the surface by migration along hypogene physico-chemical gradients in time and space, as vein material was reworked by mineralizing fluids. The pattern of wallrock alteration throughout the district grades from silicification and scricitization adjacent to the veins, through argillization and propylitization, to widespread chloritization farther away. Mineralization can be divided into three stages: 1) Preparatory stage, characterized by

Ore controls in the Charters Towers goldfield, NE Australia: Constraints from geological, geophysical and numerical analyses

USGS Publications Warehouse

Kreuzer, O.P.; Blenkinsop, T.G.; Morrison, R.J.; Peters, S.G.

2007-01-01

The approach taken in this paper, namely synthesising a wealth of previous information with new data and a genetic model, in combination with integrated numerical analyses, led to new insights into the geological controls on the localisation of auriferous veins and residual prospectivity of the Charters Towers goldfield, NE Australia. The method also has implications for the assessment of other "mature" goldfields worldwide. Despite a number of different ore controls having operated within the Charters Towers goldfield, the controlling factors can be linked to a single genetic model for orogenic, granitoid-hosted lode-gold mineralisation in a brittle deformation regime (D4) of NE-SW to NNE-SSW shortening, under conditions of supralithostatic fluid pressure and low stress difference. Spatial autocorrelation results suggest district-scale alignment of the auriferous veins parallel to and overlapping with the ESE-WNW- to E-W-striking Charters Towers-Ravenswood lineament, a major crustal boundary in the basement to the Ravenswood batholith. At the camp-scale, auriferous veins have abundance and proximity relationships with NW-SE-, NNW-SSE-, NE-SW- and ENE-WSW-oriented lineaments, suggesting that structures that controlled gold deposition in one camp did not necessarily control mineralisation in other camps. Fractal dimensions obtained with the box-counting method range from 1.02 to 1.10, whereas veins in the Charters Towers City camp are characterised by a significantly higher fractal dimension of 1.28. This discrepancy may be taken to imply that most or all outcropping and near-surface deposits within the Charters Towers City camp have been found and that new discoveries are more likely to occur at greater levels of depth, or outside the boundaries of this camp. The new understanding has implications for the assessment of the residual prospectivity of the Charters Towers goldfield, where large areas of prospective rock types and structures (e.g., approximately 40% of

Hybrid gravity survey to search for submarine ore deposit

NASA Astrophysics Data System (ADS)

Araya, A.; Kanazawa, T.; Fujimoto, H.; Shinohara, M.; Yamada, T.; Mochizuki, K.; Iizasa, K.; Ishihara, T.; Omika, S.

2011-12-01

Along with seismic surveys, gravity survey is a useful method to profile the underground density structure. We propose a hybrid gravity survey using gravimeters and gravity gradiometers to detect submarine ore deposits as density anomalies by towing the instruments using an AUV (Autonomous Underwater Vehicle) or an ROV (Remotely Operated Vehicle). Gravimeters measure the regional density structure below the seafloor, whereas gravity gradiometers are sensitive to localized mass distribution. A gravity gradiometer comprises two accelerometers arranged with a vertical separation, and a gravity gradient can be obtained from the acceleration difference. Compared to gravimeters, gravity gradiometers are insensitive to common disturbances such as parallel acceleration, thermal drift, and apparent gravity effect (Eötvös effect). We made two accelerometers using astatic pendulums, and obtained common acceleration reduction more than two orders of magnitude. With these pendulums of 500-mm separation, resolution of 7E (=7x10^{-9}(1/s^2)), enough to detect a typical ore deposit buried 50m below the seafloor, was evaluated. During measurements using a submersible mobile object, instrument orientation is required to be controlled to keep verticality and to reduce centrifugal force associated with rotation of the instrument. Using a gyro and a tiltmeter, angular rotation was shown to be controlled within 0.001deg/s which corresponds to 0.3E in effective gravity gradient due to the centrifugal force. In this paper, target of this research, details of the instruments and their performance, and development for the submarine gravity survey using an AUV will be presented.

REE Mineralization in Kiruna-type Magnetite-Apatite Ore Deposits: Magmatism and Metasomatism

NASA Astrophysics Data System (ADS)

Harlov, D. E.

2015-12-01

,K)Cl) fluids originating in the surrounding country rock or as fluids associated with metamorphic events such as regional albitization or actinolization. The abundance of (Y+REE)-bearing minerals in these deposits suggests that in addition to being mined for their Fe ore, they could also be economically mined for (Y+REE) as well.

Variscan ore formation and metamorphism at the Felbertal scheelite deposit (Austria): constraining tungsten mineralisation from Re-Os dating of molybdenite

NASA Astrophysics Data System (ADS)

Raith, Johann G.; Stein, Holly J.

2006-10-01

The Felbertal scheelite deposit in the Eastern Alps has been regarded as the type locality for stratabound scheelite deposits. It is hosted by a Cambro-Ordovician metavolcanic arc sequence with minor Variscan granitoids (˜ 340 Ma) in the central Tauern Window. Re-Os model ages for molybdenite from the Felbertal tungsten deposit range between ˜ 358 and ˜ 336 Ma and record several pulses of magmatic-hydrothermal-metamorphic molybdenite formation. Molybdenite ages from the K2 orebody, a scheelite-rich quartz mylonite in the Western ore field, indicate that both mineralisation and mylonite are Variscan in age and suggest that the shear zone was active for ˜ 20 million years. Early stage tungsten mineralisation ( Scheelite 1) in quartzitic ores in the Eastern ore field, which is free of molybdenite, yielded very low to near blank levels of Re and Os and thus could not be dated. However, molybdenite from scheelite-quartz stringers, previously interpreted as a feeder stockwork to quartzitic scheelite ore of presumed Cambrian age, yielded Variscan Re-Os ages of ˜ 342 and ˜ 337 Ma. Dating of molybdenite contained in scheelite ores thus far provides no indication of a Cambrian component to the tungsten mineralisation. Our data are consistent with a model of either granite intrusion-related ore formation and coeval metamorphic overprint during the Early Carboniferous or, alternatively, molybdenite formation may be exclusively attributed to Variscan metamorphism (see Stein 2006).

Identifying potential disaster zones around the Verkhnekamskoye potash deposit (Russia) using advanced information technology (IT)

NASA Astrophysics Data System (ADS)

Royer, J. J.; Filippov, L. O.

2017-07-01

This work aims at improving the exploitation of the K, Mg, salts ore of the Verkhnekamskoye deposit using advanced information technology (IT) such as 3D geostatistical modeling techniques together with high performance flotation. It is expected to provide a more profitable exploitation of the actual deposit avoiding the formation of dramatic sinkholes by a better knowledge of the deposit. The GeoChron modelling method for sedimentary formations (Mallet, 2014) was used to improve the knowledge of the Verkhnekamskoye potash deposit, Perm region, Russia. After a short introduction on the modern theory of mathematical modelling applied to mineral resources exploitation and geology, new results are presented on the sedimentary architecture of the ore deposit. They enlighten the structural geology and the fault orientations, a key point for avoiding catastrophic water inflows recharging zone during exploitation. These results are important for avoiding catastrophic sinkholes during exploitation.

First find of platinum group metals in the ore of Kirganik copper-porphyry deposit (Kamchatka)

NASA Astrophysics Data System (ADS)

Sidorov, E. G.; Ignatyev, E. K.; Chubarov, V. M.

2017-08-01

The Kirganik copper-porphyry deposit is situated in the central part of the Sredinnyi Mountain Range of Kamchatka and is confined to fields of development of potassic orthoclase metasomatite and hypabyssal intrusions of shonkinite. Platinum group metals (PGMs), such as merenskyite, kotulskite, keithconnite, and temagamite, were discovered in the chalcopyrite-bornite and chalcopyrite-bornite-chalcosine ore of the deposit for the first time.

High REE and Y concentrations in Co-Cu-Au ores of the Blackbird district, Idaho

USGS Publications Warehouse

Slack, J.F.

2006-01-01

Analysis of 11 samples of strata-bound Co-Cu-Au ore from the Blackbird district in Idaho shows previously unknown high concentrations of rare earth elements (REE) and Y, averaging 0.53 wt percent ???REE + Y oxides. Scanning electron microscopy indicates REE and Y residence in monazite, xenotime, and allanite that form complex intergrowths with cobaltite, suggesting coeval Co and REE + Y mineralization during the Mesoproterozoic. Occurrence of high REE and Y concentrations in the Blackbird ores, together with previously documented saline-rich fluid inclusions and Cl-rich biotite, suggest that these are not volcanogenic massive sulfide or sedimentary exhalative deposits but instead are iron oxide-copper-gold (IOCG) deposits. Other strata-bound Co deposits of Proterozoic age in the North American Cordillera and elsewhere in the world may have potential for REE and Y resources. IOCG deposits with abundant light REE should also be evaluated for possible unrecognized heavy REE and Y mineralization. ?? 2006 by Economic Geology.

Stratigraphy of Upper Cretaceous and Cenozoic deposits of the Bakchar iron ore deposit (southwestern Siberia): New data

NASA Astrophysics Data System (ADS)

Lebedeva, N. K.; Kuzmina, O. B.; Sobolev, E. S.; Khazina, I. V.

2017-01-01

The results of complex palynological and microfaunistic studies of Upper Cretaceous and Cenozoic deposits of the Bakchar iron ore deposit are presented. Geochronologically, the age of the deposits varies from Campanian to Quaternary. It was established that the Slavgorod, Gan'kino, and Jurki (?) formations contain four biostratons in the rank of beds with dinocysts and three biostratons in the rank of beds with spores and pollen. The Cenozoic continental deposits contain four biostratons in the rank of beds, containing spores and pollen. As a result of the study, a large stratigraphic gap in the Cretaceous-Paleogene boundary deposits, covering a significant part of the Maastrichtian, Paleocene, Ypresian, and Lutetian stages of the Eocene, was established. The remnants of a new morphotype of heteromorphic ammonites of genus Baculites were first described in deposits of the Slavgorod Formation (preliminarily, upper Campanian). The distribution features of the different palynomorph groups in the Upper Cretaceous-Cenozoic deposits in the area of study due to transgressive-regressive cycles and climate fluctuations were revealed.

Economic geology of the Bingham mining district, Utah, with a section on areal geology, and an introduction on general geology

USGS Publications Warehouse

Boutwell, J.M.; Keith, Arthur; Emmons, S.F.

1905-01-01

The field work of which this report represents the final results was first undertaken in the summer of the year 1900. This district had long been selected by the writer as worthy of special economic investigation, as well on account of the importance of its products as because of its geological structure and the peculiar relations of its ore deposits. It was not, however, until the summer mentioned above that the means at the disposal of the Survey, both pecuniary and scientific, justified its undertaking. As originally planned, the areal or surface geology was to have been worked out by Mr. Keith, who had already spent many years in unraveling the complicated geological structure of the Appalachian province, while Mr. Boutwell, who had more recently become attached to the Survey, was to have charge of the underground geology, or a study of the ore deposits, under the immediate supervision of the writer. When the time came for actually taking the field, it was found that the pressure of other work would not permit Mr. Keith to carry out fully the part allotted to him, and in consequence a part of his field work has fallen to Mr. Boutwell. Field work was commenced by the writer and Mr. Boutwell early in July, 1900. Mr. Keith joined the party on August 10, but was obliged to leave for other duties early in September. Mr. Boutwell carried on his field work continuously from July until December, taking up underground work after the snowfall had rendered work on the surface geology impracticable. The geological structure had proved to be unexpectedly intricate and complicated, so that, on the opening of the field season of 1901, it was found necessary to make further study in the light of results already worked out, and Mr. Boutwell spent some weeks in the district in the early summer of 1901. His field work that year, partly in California and partly in Arizona, as assistant to Mr. Waldemar Lindgren, lasted through the summer and winter and well into the spring of 1902

Geology and ore deposits of the McDermitt Caldera, Nevada-Oregon

USGS Publications Warehouse

Rytuba, James J.

1976-01-01

The McDermitt caldera is a Miocene collapse structure along the Nevada-Oregon border. The oval-shaped caldera is bounded by arcuate normal faults on the north and south and by rhyolite ring domes on the west. Precollapse ash-flow tuffs exposed within the south caldera rim consist of three cooling units and are peralkaline in composition. Refractive indexes of nonhydrated glasses from basal vitrophyres of the. units range from 1.493 to 1.503 and are typical of comendites. Post-collapse intracaldera rocks consist of tuffaceous lake sediments, rhyolite flows and domes, and ash-flow tuffs. Within the caldera are the mercury mines of Bretz, Cordero, McDermitt, Opalite, and Ruja and the Moonlight uranium mine. The mercury mines are adjacent to ring fracture faults, and the uranium mine and other uranium occurrences are located within rhyolite ring domes. Fluid inclusions in quartz indicate a deposition temperature of 340?C for the uranium deposit and 200?C for the mercury deposits. The mercury deposits formed at shallow depth by replacement of lakebed sediments and volcanic rocks.

Copper Deposits in Sedimentary and Volcanogenic Rocks

USGS Publications Warehouse

Tourtelot, Elizabeth B.; Vine, James David

1976-01-01

Copper deposits occur in sedimentary and volcanogenic rocks within a wide variety of geologic environments where there may be little or no evidence of hydrothermal alteration. Some deposits may be hypogene and have a deep-seated source for the ore fluids, but because of rapid cooling and dilution during syngenetic deposition on the ocean floor, the resulting deposits are not associated with hydrothermal alteration. Many of these deposits are formed at or near major tectonic features on the Earth's crust, including plate boundaries, rift valleys, and island arcs. The resulting ore bodies may be stratabound and either massive or disseminated. Other deposits form in rocks deposited in shallow-marine, deltaic, and nonmarine environments by the movement and reaction of interstratal brines whose metal content is derived from buried sedimentary and volcanic rocks. Some of the world's largest copper deposits were probably formed in this manner. This process we regard as diagenetic, but some would regard it as syngenetic, if the ore metals are derived from disseminated metal in the host-rock sequence, and others would regard the process as epigenetic, if there is demonstrable evidence of ore cutting across bedding. Because the oxidation associated with diagenetic red beds releases copper to ground-water solutions, red rocks and copper deposits are commonly associated. However, the ultimate size, shape, and mineral zoning of a deposit result from local conditions at the site of deposition - a logjam in fluvial channel sandstone may result in an irregular tabular body of limited size; a petroleum-water interface in an oil pool may result in a copper deposit limited by the size and shape of the petroleum reservoir; a persistent thin bed of black shale may result in a copper deposit the size and shape of that single bed. The process of supergene enrichment has been largely overlooked in descriptions of copper deposits in sedimentary rocks. However, supergene processes may be

Stable Te isotope fractionation in tellurium-bearing minerals from precious metal hydrothermal ore deposits

NASA Astrophysics Data System (ADS)

Fornadel, Andrew P.; Spry, Paul G.; Haghnegahdar, Mojhgan A.; Schauble, Edwin A.; Jackson, Simon E.; Mills, Stuart J.

2017-04-01

reduced vapor to a solid is necessary to form the common tellurides and native tellurium in ore-forming systems. Our data suggest that these sorts of reactions during mineralization may account for a ∼3‰ range of δ130/125Te values. Based on the data ranges for Te minerals from various ore deposits, the underpinning geologic processes responsible for mineralization seem to have primary control on the magnitude of fractionation, with tellurides in epithermal gold deposits showing a narrower range of isotope values than those in orogenic gold and volcanogenic massive sulfide deposits.

Extraction of reduced alteration information based on Aster data: a case study of the Bashibulake uranium ore district

NASA Astrophysics Data System (ADS)

Ye, Fa-wang; Liu, De-chang

2008-12-01

Practices of sandstone-type uranium exploration in recent years in China indicate that the uranium mineralization alteration information is of great importance for selecting a new uranium target or prospecting in outer area of the known uranium ore district. Taking a case study of BASHIBULAKE uranium ore district, this paper mainly presents the technical minds and methods of extracting the reduced alteration information by oil and gas in BASHIBULAKE ore district using ASTER data. First, the regional geological setting and study status in BASHIBULAKE uranium ore district are introduced in brief. Then, the spectral characteristics of altered sandstone and un-altered sandstone in BASHIBULAKE ore district are analyzed deeply. Based on the spectral analysis, two technical minds to extract the remote sensing reduced alteration information are proposed, and the un-mixing method is introduced to process ASTER data to extract the reduced alteration information in BASHIBULAKE ore district. From the enhanced images, three remote sensing anomaly zones are discovered, and their geological and prospecting significances are further made sure by taking the advantages of multi-bands in SWIR of ASTER data. Finally, the distribution and intensity of the reduced alteration information in Cretaceous system and its relationship with the genesis of uranium deposit are discussed, the specific suggestions for uranium prospecting orientation in outer of BASHIBULAKE ore district are also proposed.

Advances in understanding the tectonic evolution of the Santa Rosalia Basin and its stratiform ore deposits: Results of the Baja Basins Research Experience for Undergraduates

NASA Astrophysics Data System (ADS)

Niemi, T. M.; Busby, C.; Murowchick, J. B.; Martinez Gutierrez, G.; Antinao Rojas, J. L.; Graettinger, A.; Dorsey, R. J.

2017-12-01

Studies conducted during the three years of the Baja Basins REU program made progress toward solving a number of geologic questions in the Santa Rosalía Basin (SRB) of central Baja California. Geochemistry and 40Ar/39Ar geochronology on volcanic rocks within the SRB record the transition from subduction (13.32-9.95 Ma) to rifting (younger than 9.42 Ma) prior to deposition of the upper Miocene Boleo Formation. In contrast, magnesian andesite lavas and intrusions on the south margin of the SRB are dated at 6.1 +/- 0.3 Ma, and may have provided the heat engine for Boleo basin mineralization, which occurs in stratabound layers called "mantos". Mineralizing fluids in the Boleo Fm had near-neutral pH, evolved from a low Eh to more oxidizing conditions, were relatively low-temperature (near ambient T during manto ore deposition), and likely derived the Cu, Zn, Co, and Mn by leaching of mafic minerals in the volcanic rocks underlying the basin. Deposition of the ores was driven by oxidation as warm spring fluids vented to subaerial or near-shore marine environments, producing blankets of precipitated oxides interlayered with detrital fine to very coarse clastic beds. Integration of geologic map and fault data with detailed sedimentology and stratigraphic analysis provides evidence for syn-basinal tilting in two orthogonal directions during deposition of the Boleo Formation and Plio-Quaternary Tirabuzón, Infierno, and Santa Rosalia formations. Pronounced tilting toward the SE is revealed by southeastward thickening and coarsening of deposits in the Boleo Formation, and was synchronous with northeastward tilting and thickening due to slip on a network of NW-striking oblique normal faults. We hypothesize that the basin formed, subsided, and deformed as a pull-apart basin in a releasing step-over between two propagating transform faults that opened the late Miocene Gulf of California. The neotectonic evolution and uplift history of the SRB is documented through mapping of

Geologic setting and genesis of the Mule Canyon low-sulfidation epithermal gold-silver deposit, north-central Nevada

USGS Publications Warehouse

John, D.A.; Hofstra, A.H.; Fleck, R.J.; Brummer, J.E.; Saderholm, E.C.

2003-01-01

The Mule Canyon mine exploited shallow, low-sulfidation, epithermal Au-Ag deposits that lie near the west side of the Northern Nevada rift in northern Lander County, Nevada. Mule Canyon consists of six small deposits that contained premining reserves of about 8.2 Mt at an average grade of 3.81 g Au/tonne. It is an uncommon mafic end member of low-sulfidation Au-Ag deposits associated with tholeiitic bimodal basalt-rhyolite magmatism. The ore is hosted by a basalt-andesite eruptive center that formed between about 16.4 to 15.8 Ma during early mafic eruptions related to regionally extensive bimodal magmatism. Hydrothermal alteration and Au-Ag ores formed at about 15.6 Ma and were tightly controlled by north-northwest- to north-striking high-angle fault and breccia zones developed during rifting, emplacement of mafic dikes, and eruption of mafic lava flows. Hydrothermal alteration assemblages are zoned outward from fluid conduits in the sequence silica-adularia, adularia-smectite, smectite (intermediate argillic), and smectite-carbonate (propylitic). All alteration types contain abundant pyrite and/or marcasite ?? arsenopyrite. Field relations indicate that silica-adularia alteration is superimposed on argillic and propylitic alteration. Little or no steam-heated acid-sulfate alteration is present, probably the result of a near-surface water table during hydrothermal alteration and ore deposition. Two distinct ore types are present at Mule Canyon: early replacement and later open-space filling. Replacement ores consist of disseminated and vesicle-filling pyrite, marcasite, and arsenopyrite in argillically altered or weakly silicified rocks. Ore minerals consist of Au-bearing arsenopyrite and arsenian pyrite overgrowths on earlier-formed pyrite and marcasite. Open-space filling ores include narrow stockwork quartz-adularia veins, banded and crustiform opaline and chalcedonic silica-adularia veins, silica-adularia cemented breccias, and sparse carbonate-pyrite and

Geology of the Egnar quadrangle, Dolores and San Miguel counties, Colorado

USGS Publications Warehouse

Cater, Fred W.; Bush, A.L.; Bell, Henry

1954-01-01

The Egnar quadrangle is one of eighteen 7 1/2-minute quadrangles covering the principal carnotite-producing area of southwestern Colorado. The geology of these quadrangles was mapped by the U.S. Geological Survey for the Atomic Energy Commission as part of a comprehensive study of carnotite deposits. The rocks exposed in the eighteen quadrangles consist of crystalline rocks of pre-Cambrian age and sedimentary rocks that range in age from late Paleozoic to Quaternary. Over much of the area the sedimentary rocks are flat lying, but in places the rocks are disrupted by hih-angle faults, and northwest-trending folds. Conspicuous among the folds are large anticlines having cores of intrusive salt and gypsum. Most of the carnotite deposits are confined to the Salt Wash sandstone member of Jurassic Morrison formation. Within this sandstone, most of the deposits are spottily distributed through an arcuate zone known as "Uruvan Mineral Belt". Individual deposits range in size from irregular masses containing only a few tons of ore to large, tabular masses containing many thousands of tons. The ore consists largely of sandstone selectively impregnated and in part replaced by uranium and vanadium minerals. Most of the deposits appear to be related to certain sedimentary structures in sandstones of favorable composition.

Sulfur isotope and trace element data from ore sulfides in the Noranda district (Abitibi, Canada): implications for volcanogenic massive sulfide deposit genesis

NASA Astrophysics Data System (ADS)

Sharman, Elizabeth R.; Taylor, Bruce E.; Minarik, William G.; Dubé, Benoît; Wing, Boswell A.

2015-06-01

We examine models for volcanogenic massive sulfide (VMS) mineralization in the ~2.7-Ga Noranda camp, Abitibi subprovince, Superior Province, Canada, using a combination of multiple sulfur isotope and trace element data from ore sulfide minerals. The Noranda camp is a well-preserved, VMS deposit-rich area that is thought to represent a collapsed volcanic caldera. Due to its economic value, the camp has been studied extensively, providing a robust geological framework within which to assess the new data presented in this study. We explore previously proposed controls on mineralization within the Noranda camp and, in particular, the exceptional Au-rich Horne and Quemont deposits. We present multiple sulfur isotope and trace element compositional data for sulfide separates representing 25 different VMS deposits and "showings" within the Noranda camp. Multiple sulfur isotope data for this study have δ34SV-CDT values of between -1.9 and +2.5 ‰, and Δ33SV-CDT values of between -0.59 and -0.03 ‰. We interpret the negative Δ33S values to be due to a contribution of sulfur that originated as seawater sulfate to form the ore sulfides of the Noranda camp VMS deposits. The contribution of seawater sulfate increased with the collapse and subsequent evolution of the Noranda caldera, an inference supported by select trace and major element analyses. In particular, higher concentrations of Se occur in samples with Δ33S values closer to 0 ‰, as well as lower Fe/Zn ratios in sphalerite, suggesting lower pressures and temperatures of formation. We also report a relationship between average Au grade and Δ33S values within Au-rich VMS deposits of the Noranda camp, whereby higher gold grades are associated with near-zero Δ33S values. From this, we infer a dominance of igneous sulfur in the gold-rich deposits, either leached from the volcanic pile and/or directly degassed from an associated intrusion.

Mississippi Valley-type lead-zinc deposits through geological time: Implications from recent age-dating research

USGS Publications Warehouse

Leach, D.L.; Bradley, D.; Lewchuk, Michael T.; Symons, David T. A.; De Marsily, G.; Brannon, J.

2001-01-01

Remarkable advances in age dating Mississippi Valley-type (MVT) lead-zinc deposits provide a new opportunity to understand how and where these deposits form in the Earth's crust. These dates are summarized and examined in a framework of global tectonics, paleogeography, fluid migration, and paleoclimate. Nineteen districts have been dated by paleomagnetic and/or radiometric methods. Of the districts that have both paleomagnetic and radiometric dates, only the Pine Point and East Tennessee districts have significant disagreements. This broad agreement between paleomagnetic and radiometric dates provides added confidence in the dating techniques used. The new dates confirm the direct connection between the genesis of MVT lead-zinc ores with global-scale tectonic events. The dates show that MVT deposits formed mainly during large contractional tectonic events at restricted times in the history of the Earth. Only the deposits in the Lennard Shelf of Australia and Nanisivik in Canada have dates that correspond to extensional tectonic events. The most important period for MVT genesis was the Devonian to Permian time, which corresponds to a series of intense tectonic events during the assimilation of Pangea. The second most important period for MVT genesis was Cretaceous to Tertiary time when microplate assimilation affected the western margin of North America and Africa-Eurasia. There is a notable paucity of MVT lead-zinc ore formation following the breakup of Rodinia and Pangea. Of the five MVT deposits hosted in Proterozoic rocks, only the Nanisivik deposit has been dated as Proterozoic. The contrast in abundance between SEDEX and MVT lead-zinc deposits in the Proterozoic questions the frequently suggested notion that the two types of ores share similar genetic paths. The ages of MVT deposits, when viewed with respect to the orogenic cycle in the adjacent orogen suggest that no single hydrologic model can be universally applied to the migration of the ore fluids

Regularities of spatial association of major endogenous uranium deposits and kimberlitic dykes in the uranium ore regions of the Ukrainian Shield

NASA Astrophysics Data System (ADS)

Kalashnyk, Anna

2015-04-01

During exploration works we discovered the spatial association and proximity time formation of kimberlite dykes (ages are 1,815 and 1,900 Ga for phlogopite) and major industrial uranium deposits in carbonate-sodium metasomatites (age of the main uranium ore of an albititic formation is 1,85-1,70 Ga according to U-Pb method) in Kirovogradsky, Krivorozhsky and Alekseevsko-Lysogorskiy uranium ore regions of the Ukrainian Shield (UkrSh) [1]. In kimberlites of Kirovogradsky ore region uranium content reaches 18-20 g/t. Carbon dioxide is a major component in the formation of hydrothermal uranium deposits and the formation of the sodium in the process of generating the spectrum of alkaline ultrabasic magmas in the range from picritic to kimberlite and this is the connection between these disparate geochemical processes. For industrial uranium deposits in carbonate-sodium metasomatitics of the Kirovogradsky and Krivorozhsky uranium ore regions are characteristic of uranyl carbonate introduction of uranium, which causes correlation between CO2 content and U in range of "poor - ordinary - rich" uranium ore. In productive areas of uranium-ore fields of the Kirovogradsky ore region for phlogopite-carbonate veinlets of uranium ore albitites deep δ13C values (from -7.9 to -6.9o/oo) are characteristic. Isotope-geochemical investigation of albitites from Novokonstantynovskoe, Dokuchaevskoe, Partyzanskoe uranium deposits allowed obtaining direct evidence of the involvement of mantle material during formation of uranium albitites in Kirovogradsky ore region [2]. Petrological characteristics of kimberlites from uranium ore regions of the UkrSh (presence of nodules of dunite and harzburgite garnet in kimberlites, diamonds of peridotite paragenesis, chemical composition of indicator minerals of kimberlite, in particular Gruzskoy areas pyropes (Cr2O3 = 6,1-7,1%, MgO = 19,33-20,01%, CaO = 4,14-4,38 %, the content of knorringite component of most grains > 50mol%), chromites (Cr2O3 = 45

Geology of the Eymir iron mine, Edremit, Turkey

USGS Publications Warehouse

Jacobson, Herbert Samuel; Turet, Erdogan

1972-01-01

The Eymir mine near Edremit on Turkey's Aegean coast (long 27?30'E.,1at 39?36'N.) was investigated as part of the Maden Tetkik ve Arama Enstitutsu (MTA)-U. S. Geological Survey (USGS) mineral exploration and training project, for the purpose of increasing the known mineral reserves. Geologic mapping of the mine area indicates that hematite is restricted to argillized, silicified, and pyritized dacite and possibly andesite. Hematite is present as massive replacements, impregnations, disseminations, and fracture fillings. Most of the upper part of the iron deposit consists of a breccia composed mostly of silicifiled dacite fragments in a hematite matrix. The iron deposit was apparently formed in three steps: 1. Argillation, silicification, and pyritization of the andesitic lava and dacite units as a result of a regional intrusion. 2. Intrusion of the Dere Oren dacite stock, with associated faulting, fracturing, and breccia formation at the surface. 3. Deposition of hematite by oxidation of pyrite, and transfer of iron via fractures and faults by hydrothermal or meteoric fluids. The Eymir iron deposit is a blanketlike deposit on the crest of the Sivritepe-Eymir ridge. It is 1300 meters long, 80 to 450 meters wide, and has an average thickness of 18.6 meters. Drill holes in the deposit show the iron content to range from 32.0 to 57.6 percent, and to average 46.5 percent. Most of the gangue is silica, and an arsenic impurity averaging 0.39 percent is present. Most of the deposit cannot be utilized as iron ore because of low iron content, high silica content, and high arsenic content. Ore-dressing tests have shown that it is feasible to concentrate the low-grade material, producing a concentrate having increased iron content and reduced silica content. Tests have shown also that the arsenic content of the ore can be reduced substantially by sintering. Further tests and economic feasibility studies are necessary to determine whether an economic marketable iron ore can be

Using marine magnetic survey data to identify a gold ore-controlling fault: a case study in Sanshandao fault, eastern China

NASA Astrophysics Data System (ADS)

Yan, Jiayong; Wang, Zhihui; Wang, Jinhui; Song, Jianhua

2018-06-01

The Jiaodong Peninsula has the greatest concentration of gold ore in China and is characterized by altered tectonite-type gold ore deposits. This type of gold deposit is mainly formed in fracture zones and is strictly controlled by faults. Three major ore-controlling faults occur in the Jiaodong Peninsula—the Jiaojia, Zhaoping and Sanshandao faults; the former two are located on land and the latter is located near Sanshandao and its adjacent offshore area. The discovery of the world’s largest marine gold deposit in northeastern Sanshandao indicates that the shallow offshore area has great potential for gold prospecting. However, as two ends of the Sanshandao fault extend to the Bohai Sea, conventional geological survey methods cannot determine the distribution of the fault and this is constraining the discovery of new gold deposits. To explore the southwestward extension of the Sanshandao fault, we performed a 1:25 000 scale marine magnetic survey in this region and obtained high-quality magnetic survey data covering 170 km2. Multi-scale edge detection and three-dimensional inversion of magnetic anomalies identify the characteristics of the southwestward extension of the Sanshandao fault and the three-dimensional distribution of the main lithologies, providing significant evidence for the deployment of marine gold deposit prospecting in the southern segment of the Sanshandao fault. Moreover, three other faults were identified in the study area and faults F2 and F4 are inferred as ore-controlling faults: there may exist other altered tectonite-type gold ore deposits along these two faults.

The Balmat-Edwards zinc-lead deposits-synsedimentary ore from Mississippi valley-type fluids.

USGS Publications Warehouse

Whelan, J.F.; Rye, R.O.; Delorraine, W.

1984-01-01

The Balmat-Edwards Zn-Pb district in New York is in Mid-Proterozoic Grenville marbles. Tabular to podiform, generally conformable massive sphalerite-galena orebodies occur at various horizons in the approx 1 km-thick marbles. Metamorphism obscured or obliterated most primary characteristics, whose reconstruction is attempted through detailed S, C, and O isotope studies of the Fowler orebody, and trace element and S isotope studies of sphalerite concentrates and composite ore samples from 22 orebodies. Sulphur isotope data reflect equilibration at near peak metamorphism with some indication of re-equilibration during retrograde metamorphism. The carbon and oxygen isotope composition of gangue carbonates suggests derivation from the host marbles. The oxygen isotope composition of gangue quartz is compatible with a chert origin or metamorphism-equilibration with other minerals. Sulphur and lead isotopes and sulphide mineralogy suggests that the ore fluids were evolved basin brines, chemically like those responsible for Mississippi Valley-type deposits. The large stratigraphic span (> 600 m) of the Balmat orebodies may be due to basin dewatering of million-year intervals. Stratigraphically increasing 34S values of evaporite-anhydrite are postulated to record hydrothermal events and to imply bacterial sulphate reduction on an unusually large scale. Such a stratigraphic increase may be a general exploration guide where sediment-hosted exhalative deposits or Mississippi Valley-type deposits occur.-G.J.N.

The Kharapeh orogenic gold deposit: Geological, structural, and geochemical controls on epizonal ore formation in West Azerbaijan Province, Northwestern Iran

USGS Publications Warehouse

Niroomand, Shojaeddin; Goldfarb, Richard J.; Moore, Farib; Mohajjel, Mohammad; Marsh, Erin E.

2011-01-01

The Kharapeh gold deposit is located along the northwestern margin of the Sanandaj–Sirjan Zone (SSZ) in the West Azerbaijan province, Iran. It is an epizonal orogenic gold deposit formed within the deformed zone between central Iran and the Arabian plate during the Cretaceous–Tertiary Zagros orogeny. The deposit area is underlain by Cretaceous schist and marble, as well as altered andesite and dacite dikes. Structural analysis indicates that the rocks underwent tight to isoclinal recumbent folding and were subsequently co-axially refolded to upright open folds during a second deformation. Late- to post-tectonic Cenozoic granites and granodiorites occur northeast of the deposit area. Mineralization mainly is recognized within NW-trending extensional structures as veins and breccia zones. Normal faults, intermediate dikes, and quartz veins, oriented subparallel to the axial surface of the Kharapeh antiform, indicate synchronous extension perpendicular to the fold axis during the second folding event. The gold-bearing quartz veins are >1 km in length and average about 6 m in width; breccia zones are 10–50 m in length and ≤1 m in width. Hydrothermal alteration mainly consists of silicification, sulfidation, chloritization, sericitization, and carbonatization. Paragenetic relationships indicate three distinct stages—replacement and silicification, brecciation and fracture filling, and cataclastic brecciation—with the latter two being gold-rich. Fluid inclusion data suggest mineral deposition at temperatures of at least 220–255°C and depths of at least 1.4–1.8 km, from a H2O–CO2±CH4 fluid of relatively high salinity (12–14 wt.% NaCl equiv.), which may reflect metamorphism of passive margin carbonate sequences. Ore fluid δ18O values between about 7‰ and 9‰ suggest no significant meteoric water input, despite gold deposition in a relatively shallow epizonal environment. Similarities to other deposits in the SSZ suggest that the deposit formed as

New insight into the origin of manganese oxide ore deposits in the Appalachian Valley and Ridge of northeastern Tennessee and northern Virginia, USA

USGS Publications Warehouse

Carmichael, Sarah K.; Doctor, Daniel H.; Wilson, Crystal G.; Feierstein, Joshua; McAleer, Ryan J.

2017-01-01

Manganese oxide deposits have long been observed in association with carbonates within the Appalachian Mountains, but their origin has remained enigmatic for well over a century. Ore deposits of Mn oxides from several productive sites located in eastern Tennessee and northern Virginia display morphologies that include botryoidal and branching forms, massive nodules, breccia matrix cements, and fracture fills. The primary ore minerals include hollandite, cryptomelane, and romanèchite. Samples of Mn oxides from multiple localities in these regions were analyzed using electron microscopy, X-ray analysis, Fourier transform infrared spectroscopy, and trace and rare earth element (REE) geochemistry. The samples from eastern Tennessee have biological morphologies, contain residual biopolymers, and exhibit REE signatures that suggest the ore formation was due to supergene enrichment (likely coupled with microbial activity). In contrast, several northern Virginia ores hosted within quartz-sandstone breccias exhibit petrographic relations, mineral morphologies, and REE signatures indicating inorganic precipitation, and a likely hydrothermal origin with supergene overprinting. Nodular accumulations of Mn oxides within weathered alluvial deposits that occur close to breccia-hosted Mn deposits in Virginia show geochemical signatures that are distinct from the breccia matrices and appear to reflect remobilization of earlier-emplaced Mn and concentration within supergene traps. Based on the proximity of all of the productive ore deposits to mapped faults or other zones of deformation, we suggest that the primary source of all of the Mn may have been deep seated, and that Mn oxides with supergene and/or biological characteristics resulted from the local remobilization and concentration of this primary Mn.

Geology of Bull Canyon quadrangle, Montrose and San Miguel counties, Colorado

USGS Publications Warehouse

Cater, Fred W.

1953-01-01

The Bull Canyon quadrangle is one of eighteen 7 1/2-minute quadrangles covering the principal carnotite-producing area of southwestern Colorado. The geology of these quadrangles was mapped by the U.S. Geological Survey for the Atomic Energy Commission as part of a comprehensive study of carnotite depots. The rocks exposed in the eighteen quadrangles consist of crystalline rocks of pre-Cambrian age and sedimentary rocks that range in age from late Paleozoic to Quaternary. Over much of the area the sedimentary rocks are flat lying, but in places the rocks are disrupted by high-angle faults and northwest-trending folds. Conspicuous among the folds are large anticlines having cores of intrusive salt and gypsum. Most of the carnotite deposits are confined to the Salt Wash sandstone member of the Jurassic Morrison formation. Within this sandstone, most of the deposits are spottily distributed through an arcuate zone known as the "Uravan Mineral Belt". Individual deposits range in size from irregular masses containing only a few tons of ore to large, tabular masses containing many thousands of tones. The ore consists largely of sandstone selectively impregnated and in part replaced by uranium and vanadium minerals. Most of the deposits appear to be related to certain sedimentary structures in sandstones of favorable composition.

The Krásná Hora, Milešov, and Příčovy Sb-Au ore deposits, Bohemian Massif: mineralogy, fluid inclusions, and stable isotope constraints on the deposit formation

NASA Astrophysics Data System (ADS)

Němec, Matěj; Zachariáš, Jiří

2018-02-01

The Krásná Hora-Milešov and Příčovy districts (Czech Republic) are the unique examples of Sb-Au subtype orogenic gold deposits in the Bohemian Massif. They are represented by quartz-stibnite veins and massive stibnite lenses grading into low-grade, disseminated ores in altered host rocks. Gold postdates the stibnite and is often replaced by aurostibite. The ore zones are hosted by hydrothermally altered dikes of lamprophyres (Krásná Hora-Milešov) or are associated with local strike-slip faults (Příčovy). Formation of Sb-Au deposits probably occurred shortly after the main gold-bearing event (348-338 Ma; Au-only deposits) in the central part of the Bohemian Massif. Fluid inclusion analyses suggest that stibnite precipitated at 250 to 130 °C and gold at 200 to 130 °C from low-salinity aqueous fluids. The main quartz gangue hosting the ore precipitated from the same type of fluid at about 300 °C. Early quartz-arsenopyrite veins are not associated with the Sb-Au deposition and formed from low-salinity, aqueous-carbonic fluid at higher pressure and temperature ( 250 MPa, 400 °C). The estimated oxygen isotope composition of the ore-bearing fluid (4 ± 1‰ SMOW; based on post-ore calcite) suggests its metamorphic or mixed magmatic-metamorphic origin and excludes the involvement of meteoric water. Rapid cooling of warm hydrothermal fluids reacting with "cold" host rock was probably the most important factor in the formation of both stibnite and gold.

A conceptual model of the copper-porphyry ore formation based on joint analysis of deep 3D geophysical models: Sorskoe complex (Russia) case study

NASA Astrophysics Data System (ADS)

Spichak, Viacheslav V.; Goidina, Alexandra G.

2017-12-01

Joint analysis of deep three-dimensional models of the electrical resistivity, seismic velocity, and density of the complex hosting the Sorskoe Cu-Mo deposit (Russia) is carried out aimed at finding geophysical markers characterizing the areas of ore generation, transportation and deposition. The three-dimensional lithology model of the study area is built based on the empirical relationship between the silica content of the rocks and seismic velocities. It is in agreement with geological and geochemical studies provided in this area earlier and could be used as a basis for forecasting locations of the copper-molybdenum ore deposits at depth. A conceptual model of the copper-porphyry complex explaining the mechanisms of ore generation, transportation from the lower to the upper crust and deposition in the upper crust is suggested. In particular, it is supposed that post-magmatic supercritical gas-water ore-bearing fluids are upwelling through the plastic crust due to the sliding of the fluid films along the cleavage planes of the foliated rocks while at the depths of the brittle upper crust this mechanism could be changed by volumetric fluid transportation along the network of large pores and cracks.

Application of plurigaussian simulation to delineate the layout of alteration domains in Sungun copper deposit

NASA Astrophysics Data System (ADS)

Talebi, Hassan; Asghari, Omid; Emery, Xavier

2013-12-01

An accurate estimation of mineral grades in ore deposits with heterogeneous spatial variations requires defining geological domains that differentiate the types of mineralogy, alteration and lithology. Deterministic models define the layout of the domains based on the interpretation of the drill holes and do not take into account the uncertainty in areas with fewer data. Plurigaussian simulation (PGS) can be an alternative to generate multiple numerical models of the ore body, with the aim of assessing the uncertainty in the domain boundaries and improving the geological controls in the characterization of quantitative attributes. This study addresses the application of PGS to Sungun porphyry copper deposit (Iran), in order to simulate the layout of four hypogene alteration zones: potassic, phyllic, propylitic and argillic. The aim of this study is to construct numerical models in which the alteration structures reflect the evolution observed in the geology.

An Analysis of the Published Mineral Resource Estimates of the Haji-Gak Iron Deposit, Afghanistan

USGS Publications Warehouse

Sutphin, D.M.; Renaud, K.M.; Drew, L.J.

2011-01-01

The Haji-Gak iron deposit of eastern Bamyan Province, eastern Afghanistan, was studied extensively and resource calculations were made in the 1960s by Afghan and Russian geologists. Recalculation of the resource estimates verifies the original estimates for categories A (in-place resources known in detail), B (in-place resources known in moderate detail), and C 1 (in-place resources estimated on sparse data), totaling 110. 8 Mt, or about 6% of the resources as being supportable for the methods used in the 1960s. C 2 (based on a loose exploration grid with little data) resources are based on one ore grade from one drill hole, and P 2 (prognosis) resources are based on field observations, field measurements, and an ore grade derived from averaging grades from three better sampled ore bodies. C 2 and P 2 resources are 1,659. 1 Mt or about 94% of the total resources in the deposit. The vast P 2 resources have not been drilled or sampled to confirm their extent or quality. The purpose of this article is to independently evaluate the resources of the Haji-Gak iron deposit by using the available geologic and mineral resource information including geologic maps and cross sections, sampling data, and the analog-estimating techniques of the 1960s to determine the size and tenor of the deposit. ?? 2011 International Association for Mathematical Geology (outside the USA).

A deposit model for magmatic iron-titanium-oxide deposits related to Proterozoic massif anorthosite plutonic suites

USGS Publications Warehouse

Woodruff, Laurel G.; Nicholson, Suzanne W.; Fey, David L.

2013-01-01

This descriptive model for magmatic iron-titanium-oxide (Fe-Ti-oxide) deposits hosted by Proterozoic age massif-type anorthosite and related rock types presents their geological, mineralogical, geochemical, and geoenvironmental attributes. Although these Proterozoic rocks are found worldwide, the majority of known deposits are found within exposed rocks of the Grenville Province, stretching from southwestern United States through eastern Canada; its extension into Norway is termed the Rogaland Anorthosite Province. This type of Fe-Ti-oxide deposit dominated by ilmenite rarely contains more than 300 million tons of ore, with between 10- to 45-percent titanium dioxide (TiO2), 32- to 45-percent iron oxide (FeO), and less than 0.2-percent vanadium (V). The origin of these typically discordant ore deposits remains as enigmatic as the magmatic evolution of their host rocks. The deposits clearly have a magmatic origin, hosted by an age-constrained unique suite of rocks that likely are the consequence of a particular combination of tectonic circumstances, rather than any a priori temporal control. Principal ore minerals are ilmenite and hemo-ilmenite (ilmenite with extensive hematite exsolution lamellae); occurrences of titanomagnetite, magnetite, and apatite that are related to this deposit type are currently of less economic importance. Ore-mineral paragenesis is somewhat obscured by complicated solid solution and oxidation behavior within the Fe-Ti-oxide system. Anorthosite suites hosting these deposits require an extensive history of voluminous plagioclase crystallization to develop plagioclase-melt diapirs with entrained Fe-Ti-rich melt rising from the base of the lithosphere to mid- and upper-crustal levels. Timing and style of oxide mineralization are related to magmatic and dynamic evolution of these diapiric systems and to development and movement of oxide cumulates and related melts. Active mines have developed large open pits with extensive waste-rock piles, but

Geological and geochemical aspects of uranium deposits. A selected, annotated bibliography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Garland, P.A.; Thomas, J.M.; Brock, M.L.

1980-06-01

A bibliography of 479 references encompassing the fields of uranium and thorium geochemistry and mineralogy, geology of uranium deposits, uranium mining, and uranium exploration techniques has been compiled by the Ecological Sciences Information Center of Oak Ridge National Laboratory. The bibliography was produced for the National Uranium Resource Evaluation Program, which is funded by the Grand Junction Office of the Department of Energy. The references contained in the bibliography have been divided into the following eight subject categories: (1) geology of deposits, (2) geochemistry, (3) genesis O deposits, (4) exploration, (5) mineralogy, (6) uranium industry, (7) reserves and resources, andmore » (8) geology of potential uranium-bearing areas. All categories specifically refer to uranium and thorium; the last category contains basic geologic information concerning areas which the Grand Junction Office feels are particularly favorable for uranium deposition. The references are indexed by author, geographic location, quadrangle name, geoformational feature, taxonomic name, and keyword.« less

Geology of the Joe Davis Hill quadrangle, Dolores and San Miguel counties, Colorado

USGS Publications Warehouse

Cater, Fred W.; Bell, Henry

1953-01-01

The Joe Davis Hill quadrangle is one of eighteen 7 1/2-minute quadrangles covering the principal carnotite-producing area of southwestern Colorado. The geology of these quadrangles was mapped by the U.S. Geological Survey for the Atomic Energy Commission as part of a comprehensive study of carnotite deposits. The rocks exposed in the eighteen quadrangles consist of crystalline rocks of pre-Cambrian age and sedimentary rocks that range in age from late Paleozoic to Quaternary. Over much of the area the sedimentary rocks are flat lying, but in places the rocks are disrupted by hih-angle faults, and northwest-trending folds. Conspicuous among the folds are large anticlines having cores of intrusive salt and gypsum. Most of the carnotite deposits are confined to Salt Wash sandstone member of the Jurassic Morrison formation. Within this sandstone, most of the deposits are spottily distributed through an arcuate zone known as the "Uravan Mineral Belt". Individual deposits range in size from irregular masses containing only a few tons of ore to large, tabular masses containing many thousands of tons. The ore consists largely of sandstone selectively impregnated and in part replaced by uranium and vanadium minerals. Most of the deposits appear to be related to certain sedimentary structures in sandstones of favorable composition.

Beyond the obvious limits of ore deposits: The use of mineralogical, geochemical, and biological features for the remote detection of mineralization

USGS Publications Warehouse

Kelley, D.L.; Kelley, K.D.; Coker, W.B.; Caughlin, B.; Doherty, M.E.

2006-01-01

Far field features of ore deposits include mineralogical, geochemical, or biological attributes that can be recognized beyond the obvious limits of the deposits. They can be primary, if formed in association with mineralization or alteration processes, or secondary, if formed from the interaction of ore deposits with the hydrosphere and biosphere. This paper examines a variety of far field features of different ore deposit types and considers novel applications to exploration and discovery. Primary far field features include mineral and rock chemistry, isotopic or element halos, fluid pathways and thermal anomalies in host-rock sequences. Examples include the use of apatite chemistry to distinguish intrusive rocks permissive for iron oxide copper gold (IOCG) and porphyry deposits; resistate mineral (e.g., rutile, tourmaline) chemistry in exploration for volcanogenic massive sulfide (VMS), orogenic gold, and porphyry deposits; and pyrite chemistry to vector toward sedimentary exhalative (sedex) deposits. Distinctive whole-rock geochemical signatures also can be recognized as a far field feature of porphyry deposits. For example, unique Sr/Y ratios in whole-rock samples, used to distinguish barren versus fertile magmas for Cu mineralization, result from the differentiation of oxidized hydrous melts. Anomalous concentrations of halogen elements (Cl, Br, and I) have been found for distances of up to 200 m away from some mineralized centers. Variations in isotopic composition between ore-bearing and barren intrusions and/or systematic vertical and lateral zonation in sulfur, carbon, or oxygen isotope values have been documented for some deposit types. Owing to the thermal aureole that extends beyond the area of mineralization for some deposits, detection of paleothermal effects through methods such as conodont alteration indices, vitrinite or bitumen reflectance, illite crystallinity, and apatite or zircon thermochronology studies also can be valuable, particularly for

New geologic, fluid inclusion and stable isotope studies on the controversial Igarapé Bahia Cu-Au deposit, Carajás Province, Brazil

NASA Astrophysics Data System (ADS)

Dreher, Ana M.; Xavier, Roberto P.; Taylor, Bruce E.; Martini, Sérgio L.

2008-02-01

contribution of reduced and oxydized sulfur is also evident. Oxygen isotopic ratios in magnetite, quartz, and siderite yield calculated temperatures of ˜400°C and δ18O-enriched compositions (5 to 16.5 per mil) for the ore-forming fluids that suggest a magmatic input and/or an interaction with 18O-rich, probably sedimentary rocks. The late veins of the Igarapé Bahia deposit area were formed from saline aqueous fluids (2 to 60 wt% NaCl + CaCl2 equiv) with δ18Ofluid compositions around 0 per mil that indicate contribution from meteoric fluids. With respect to geological features, Igarapé Bahia bears similarity with syngenetic, volcanic-hosted massive sulfide (VHMS)-type deposits, as indicated by the volcano-sedimentary geological context, stratabound character, and association with submarine volcanic flows, hyaloclastite, and exhalative beds such as BIF and chert. On the other hand, the highly saline ore fluids and the mineral assemblage, dominated by magnetite and chalcopyrite, with associated gold, U- and LREE-minerals and scarce pyrite, indicate that Igarapé Bahia belongs to the Fe oxide Cu-Au (IOCG) group of deposits. The available geochronologic data used to attest syngenetic or epigenetic origins for the mineralization are either imprecise or may not represent the main mineralization episode but a later, superimposed event. The C, S, and O isotopic results obtained in this study do not clearly discriminate between fluid sources. However, recent B isotope data obtained on tourmaline from the matrix of the fragmental rock ore unit (Xavier, Wiedenbeck, Dreher, Rhede, Monteiro, Araújo, Chemical and boron isotopic composition of tourmaline from Archean and Paleoproterozoic Cu-Au deposits in the Carajás Mineral Province, 1° Simpósio Brasileiro de Metalogenia, Gramado, Brazil, extended abstracts, CD-ROM, 2005) provide strong evidence of the involvement of a marine evaporitic source in the hydrothermal system of Igarapé Bahia. Evaporite-derived fluids may explain the

Variations in the uranium isotopic compositions of uranium ores from different types of uranium deposits

NASA Astrophysics Data System (ADS)

Uvarova, Yulia A.; Kyser, T. Kurt; Geagea, Majdi Lahd; Chipley, Don

2014-12-01

Variations in 238U/235U and 234U/238U ratios were measured in uranium minerals from a spectrum of uranium deposit types, as well as diagenetic phosphates in uranium-rich basins and peraluminous rhyolites and associated autunite mineralisation from Macusani Meseta, Peru. Mean δ238U values of uranium minerals relative to NBL CRM 112-A are 0.02‰ for metasomatic deposits, 0.16‰ for intrusive, 0.18‰ for calcrete, 0.18‰ for volcanic, 0.29‰ for quartz-pebble conglomerate, 0.29‰ for sandstone-hosted, 0.44‰ for unconformity-type, and 0.56‰ for vein, with a total range in δ238U values from -0.30‰ to 1.52‰. Uranium mineralisation associated with igneous systems, including low-temperature calcretes that are sourced from U-rich minerals in igneous systems, have low δ238U values of ca. 0.1‰, near those of their igneous sources, whereas uranium minerals in basin-hosted deposits have higher and more variable values. High-grade unconformity-related deposits have δ238U values around 0.2‰, whereas lower grade unconformity-type deposits in the Athabasca, Kombolgie and Otish basins have higher δ238U values. The δ234U values for most samples are around 0‰, in secular equilibrium, but some samples have δ234U values much lower or higher than 0‰ associated with addition or removal of 234U during the past 2.5 Ma. These δ238U and δ234U values suggest that there are at least two different mechanisms responsible for 238U/235U and 234U/238U variations. The 234U/238U disequilibria ratios indicate recent fluid interaction with the uranium minerals and preferential migration of 234U. Fractionation between 235U and 238U is a result of nuclear-field effects with enrichment of 238U in the reduced insoluble species (mostly UO2) and 235U in oxidised mobile species as uranyl ion, UO22+, and its complexes. Therefore, isotopic fractionation effects should be reflected in 238U/235U ratios in uranium ore minerals formed either by reduction of uranium to UO2 or chemical

Book review: Economic geology: Principles and practice: Metals, minerals, coal and hydrocarbons—Introduction to formation and sustainable exploitation of mineral deposits

USGS Publications Warehouse

Anderson, Eric

2013-01-01

This volume, available in both hardcover and paperback, is an English translation of the fifth edition of the German language text Mineralische und Energie-Rohstoffe. The book provides an extensive overview of natural resources and societal issues associated with extracting raw materials. The comprehensive list of raw materials discussed includes metals, industrial minerals, coal, and hydrocarbons. The book is divided into four parts: (1) “Metalliferous ore deposits,” (2) “Nonmetallic minerals and rocks,” (3) “Practice of economic geology,” and (4) “Fossil energy raw materials—coal, oil, and gas.” These sections are bound by a brief introduction and an extensive list of up-to-date references as well as an index. Each chapter begins with a concise synopsis and concludes with a summary that contains useful suggestions for additional reading. All figures are grayscale images and line drawings; however, several have been grouped together and reproduced as color plates. Also included is a companion website (www.wiley.com/go/pohl/geology) that contains additional resources, such as digital copies of figures, tables, and an expanded index, all available for download in easy-to-use formats.Economic Geology: Principles and Practice: Metals, Minerals, Coal and Hydrocarbons—Introduction to Formation and Sustainable Exploitation of Mineral Deposits. Walter l. Pohl. 2011. Wiley-Blackwell. Pp. 663. ISBN 978-1-4443-3663-4 (paperback).

Exploratory drilling in the Prairie du Chien group of the Wisconsin zinc-lead districts by the U.S. Geological Survey in 1949-1950

USGS Publications Warehouse

Heyl, Allen Van; Lyons, Erwin J.; Agnew, Allen F.

1951-01-01

The U. S. Geological Survey in cooperation with the Wisconsin Geological and Natural History Survey explored the Prairie du Chien group in the main productive area of the Wisconsin zinc-lead district during 1949-50. Eight properties--Crow Branch diggings, Leix, Harris, Spitzbarth, Kennedy, James, Raisbeck and Vinegar Hill Roaster--were explored using both diamond and churn drills. Twenty holes were drilled that totaled 8,582 feet in depth. The objectives of the exploration were to determine if the Prairie du Chien and other formations below the principal ore-bearing strata (Galena, Decorah, and Platteville formations) of the district are favorable for ore deposits, and to determine the type of ore deposits, if present. Lean deposits of sphalerite, marcasite, and pyrite were found in the Prairie du Chien on five properties--Crow Branch, Leix, Harris, Spitzbarth, and Vinegar Hill 1%ouster-and also in the Franconia sandstone on the Leix property. In the drilled area the sulfides in the Prairie du Chien group occur in certain more brittle or soluble dolomite beds that contain cavities formed by brecciation or solution.

Chemical Equilibrium of the Dissolved Uranium in Groundwaters From a Spanish Uranium-Ore Deposit

DOE Office of Scientific and Technical Information (OSTI.GOV)

Garralon, Antonio; Gomez, Paloma; Turrero, Maria Jesus

2007-07-01

The main objectives of this work are to determine the hydrogeochemical evolution of an uranium ore and identify the main water/rock interaction processes that control the dissolved uranium content. The Mina Fe uranium-ore deposit is the most important and biggest mine worked in Spain. Sageras area is located at the north part of the Mina Fe, over the same ore deposit. The uranium deposit was not mined in Sageras and was only perturbed by the exploration activities performed 20 years ago. The studied area is located 10 Km northeast of Ciudad Rodrigo (Salamanca) at an altitude over 650 m.a.s.l. Themore » uranium mineralization is related to faults affecting the metasediments of the Upper Proterozoic to Lower Cambrian schist-graywacke complex (CEG), located in the Centro-Iberian Zone of the Hesperian Massif . The primary uranium minerals are uraninite and coffinite but numerous secondary uranium minerals have been formed as a result of the weathering processes: yellow gummite, autunite, meta-autunite, torbernite, saleeite, uranotile, ianthinite and uranopilite. The water flow at regional scale is controlled by the topography. Recharge takes place mainly in the surrounding mountains (Sierra Pena de Francia) and discharge at fluvial courses, mainly Agueda and Yeltes rivers, boundaries S-NW and NE of the area, respectively. Deep flows (lower than 100 m depth) should be upwards due to the river vicinity, with flow directions towards the W, NW or N. In Sageras-Mina Fe there are more than 100 boreholes drilled to investigate the mineral resources of the deposit. 35 boreholes were selected in order to analyze the chemical composition of groundwaters based on their depth and situation around the uranium ore. Groundwater samples come from 50 to 150 m depth. The waters are classified as calcium-bicarbonate type waters, with a redox potential that indicates they are slightly reduced (values vary between 50 to -350 mV). The TOC varies between <0.1 and 4.0 mgC/L and the

Development of Technology for Enrichment of Silver Containing Ores

NASA Astrophysics Data System (ADS)

Shekiladze, Asmati; Kavtelashvili, Otari; Bagnashvili, Mamuka

2016-10-01

The progress of Georgian economics is substantially associated with a development of new deposits of mineral resources. Among them is the David-Gareji deposit where at present the intensive searching geological works are performed. The work goal involves the elaboration of the technology for processing of silver-containing quartz-barite ores. Without its development the mining of more valuable gold-polymetallic ores is impossible. Because of ore complexity silver and barite are considered in a common technological aspect. The investigations were carried out on the representative samples of quartz-barite ores containing 78-88 g/ton of silver and 27-29 % of silver is a nugget in the form of the simple sulphides and chlorides. The ore is characterized by fine coalescence of barite and ore-generating minerals. Non-ferrous metals haven't any industrial value because of their very low content. Therefore, for the processing of the ores under study the direct selective scheme of flotation enrichment was chosen and the formula of optimal reagent regime was elaborated. Potassium xanthogenate is used as a collector for flotation of silver minerals and pine oil- as a foaming agent. The effect of the pulp - pH and medium temperature on silver flotation was studied. It was established that the silver is actively floats in neutral medium. For barite flotation the various collectors were tested: sulfidezid cotton oil-soap stock, soaps of fatty acids and alkyl sulphates of C12 - C16 row, among the “Baritol” is the most efficient one. Depression of the barren rock was carried out by liquid glass in alkaline medium. The effect of pulp pH on barite flotation has been investigated. The best results were obtained at pH=8.5. The increase of the pulp alkalinity has no essential effect on the indexes of the barite enrichment. Conditional concentrate of the barite is obtained by two fold purification of the main flotation concentrate by the addition of the liquid glass to the re

Fractals in geology and geophysics

NASA Technical Reports Server (NTRS)

Turcotte, Donald L.

1989-01-01

The definition of a fractal distribution is that the number of objects N with a characteristic size greater than r scales with the relation N of about r exp -D. The frequency-size distributions for islands, earthquakes, fragments, ore deposits, and oil fields often satisfy this relation. This application illustrates a fundamental aspect of fractal distributions, scale invariance. The requirement of an object to define a scale in photograhs of many geological features is one indication of the wide applicability of scale invariance to geological problems; scale invariance can lead to fractal clustering. Geophysical spectra can also be related to fractals; these are self-affine fractals rather than self-similar fractals. Examples include the earth's topography and geoid.

Analysis of borehole geophysical information across a uranium deposit in the Jackson Group, Karnes County, Texas

USGS Publications Warehouse

Daniels, Jeffrey J.; Scott, James Henry; Smith, Bruce D.

1979-01-01

Borehole geophysical studies across a uranium deposit in the Jackson Group, South Texas, show the three geochemical environments often associated with uranium roll-type deposits: an altered (oxidized) zone, an ore zone, and an unaltered (reduced) zone. Mineralogic analysis of the total sulfides contained in the drill core shows only slight changes in the total sulfide content among the three geochemical regimes. However, induced polarization measurements on the core samples indicate that samples obtained from the reduced side of the ore zone are more electrically polarizable than those from the oxidized side of the ore zone, and therefore probably contain more pyrite. Analysis of the clay-size fraction in core samples indicates that montmorillonite is the dominant clay mineral. High resistivity values within the ore zone indicate the presence of calcite cement concentrations that are higher than those seen outside of the ore zone. Between-hole resistivity and induced polarization measurements show the presence of an extensive zone of calcite cement within the ore zone, and electrical polarizable material (such as pyrite) within and on the reduced side of the ore zone. A quantitative analysis of the between-hole resistivity data, using a layered-earth model, and a qualitative analysis of the between-hole induced polarization measurements showed that mineralogic variations among the three geochemical environments were more pronounced than were indicated by the geophysical and geologic well logs. Uranium exploration in the South Texas Coastal Plain area has focused chiefly in three geologic units: the Oakville Sandstone, the Catahoula Tuff, and the Jackson Group. The Oakville Sandstone and the Catahoula Tuff are of Miocene age, and the Jackson Group is of Eocene age (Eargle and others, 1971). Most of the uranium mineralization in these formations is low grade (often less than 0.02 percent U3O8) and occurs in shallow deposits that are found by concentrated exploratory

Sources of Matter and Ore-Producing Fluid of the Tamunyer Gold-Sulfide Deposit (Northern Urals): Isotope Results

NASA Astrophysics Data System (ADS)

Zamyatina, D. A.; Murzin, V. V.

2018-02-01

The Tamunyer deposit is a typical example of gold-sulfide mineralization located in the lower lithologic-stratigraphic unit (S2-D1) of the Auerbach volcanic-plutonic belt. The latter comprises island-arc andesitic volcano-sediments, volcanics, and comagmatic intrusive formations. Carbonates have demonstrated intermediate values of δ13C between marine limestone and mantle. The quartz δ18O is in the range of 15.3-17.2‰. The δ34S of sulfides from the beresitized volcano-sedimentary rocks and ores varies widely from -7.5 to 12‰. The calculated isotope compositions of H2O, CO2, and H2S of the ore-bearing fluid imply two major sources of matter contributing to ore genesis: local rocks and foreign fluid. The ore-bearing fluid was formed by interaction and isotope equilibration between a deep magmatic fluid and marine carbonates (W/R 1), with the contribution of sulfur from the volcano-sedimentary rocks.

Geology and recognition criteria for sandstone uranium deposits in mixed fluvial-shallow marine sedimentary sequences, South Texas. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adams, S.S.; Smith, R.B.

1981-01-01

Uranium deposits in the South Texas Uranium Region are classical roll-type deposits that formed at the margin of tongues of altered sandstone by the encroachment of oxidizing, uraniferous solutions into reduced aquifers containing pyrite and, in a few cases, carbonaceous plant material. Many of the uranium deposits in South Texas are dissimilar from the roll fronts of the Wyoming basins. The host sands for many of the deposits contain essentially no carbonaceous plant material, only abundant disseminated pyrite. Many of the deposits do not occur at the margin of altered (ferric oxide-bearing) sandstone tongues but rather occur entirely within reduced,more » pyurite-bearing sandstone. The abundance of pyrite within the sands probably reflects the introduction of H/sub 2/S up along faults from hydrocarbon accumulations at depth. Such introductions before ore formation prepared the sands for roll-front development, whereas post-ore introductions produced re-reduction of portions of the altered tongue, leaving the deposit suspended in reduced sandstone. Evidence from three deposits suggests that ore formation was not accompanied by the introduction of significant amounts of H/sub 2/S.« less

Geology and structural evolution of the Muruntau gold deposit, Kyzylkum desert, Uzbekistan

USGS Publications Warehouse

Drew, L.J.; Berger, B.R.; Kurbanov, N.K.

1996-01-01

The Muruntau gold deposit in the Kyzylkum desert of Uzbekistan is the largest single deposit (??? 1100 tonnes of gold) of the class of low-sulfide syndeformation/synigenous gold deposits formed in the brittle/ductile transition zone of the crust within transpressional shear zones. Hosted by the Cambrian to Ordovician Besopan Suite, the ores were deposited in pre-existing thrust-fault- and metamorphism-related permeabilities and in synmineralization dilational zones created in a large fault-related fold. The Besopan Suite is a 5,000-m-thick sequence of turbiditic siltstones, shales and sandstones. The ore is primarily localized at the base of the Besopan-3 unit, which is a 2,000-m-thick series of carbonaceous shales, siltstones, sandstones and cherts. Initial gold deposition took place within the Sangruntau-Tamdytau shear zone, which was developed along the stratigraphic contact between the Besopan-3 and Besopan-4 units. During the mineralization process, folding of the Besopan Suite and a left-step adjustment in the Sangruntau-Tamdytau shear zone were caused by two concurrent events: (1) the activation of the left-lateral Muruntau-Daugyztau shear zone that developed at nearly a 90?? angle to the preceding shear zone and (2) the intrusion of granitoid plutons. These structural events also resulted in the refocusing of hydrothermal fluid flow into new zones of permeability.

Geology and geochemistry of the Reocín zinc-lead deposit, Basque-Cantabrian Basin, Northern Spain

USGS Publications Warehouse

Velasco, Francisco; Herrero, Jose Miguel; Yusta, Inaki; Alonso, Jose Antonio; Seebold, Ignacio; Leach, David

2003-01-01

The Reoci??n Zn-Pb deposit, 30 km southwest of Santander, Spain, occurs within Lower Cretaceous dolomitized Urgonian limestones on the southern flank of the Santillana syncline. The Reoci??n deposit is one of the largest known strata-bound, carbonate-hosted, zinc-lead deposits in Europe. The total metal endowment of the deposit, including past production and remaining reserves, is 62 Mt of ore grading 8.7 percent Zn and 1.0 percent Pb. The epigenetic mineralization consists of sphalerite and galena, with lesser marcasite and trace pyrite with dolomite as gangue. Microprobe analyses of different generations of dolomite revealed nonstoichiometric compositions with various amounts of iron (up to 14 mol % of FeCO3). Replacement of host dolomite, open-space filling of fractures, and cementation of breccias derived from dissolution collapse are the principal types of ore occurrence. Detailed cross-section mapping indicates a stratigraphic and structural control on the deposit. A stratiform morphology is present in the western part of the orebody (Capa Sur), whereas mineralization in the eastern part is highly discordant but strata bound (Barrendera). Stratigraphic studies demonstrate that synsedimentary tectonic activity, related to the rifting of the North Atlantic (Bay of Biscay), was responsible for variation in sedimentation, presence of unconformities (including paleokarsts), local platform emergence and dolomitization along the N60 fault trend. In the Reoci??n area, two stages of dolomitization are recognized. The first stage is a pervasive dolomitization of the limestone country rocks that was controlled by faulting and locally affected the upper part of the Aptian and the complete Albian sequence. The second dolomitization event occurred after erosion and was controlled by karstic cavities. This later dolomitization was accompanied by ore deposition and, locally, filling of dolomite sands and clastic sediments in karstic cavities. The circulation of hydrothermal

Numerical Approaches about the Morphological Description Parameters for the Manganese Deposits on the Magnesite Ore Surface

NASA Astrophysics Data System (ADS)

Bayirli, Mehmet; Ozbey, Tuba

2013-07-01

Black deposits usually found at the surface of magnesite ore or limestone as well as red deposits in quartz veins are named as natural manganese dendrites. According to their geometrical structures, they may take variable fractal shapes. The characteristic origins of these morphologies have rarely been studied by means of numerical analyses. Hence, digital images of magnesite ore are taken from its surface with a scanner. These images are then converted to binary images in the form of 8 bits, bitmap format. As a next step, the morphological description parameters of manganese dendrites are computed by the way of scaling methods such as occupied fractions, fractal dimensions, divergent ratios, and critical exponents of scaling. The fractal dimension and the scaling range are made dependent on the fraction of the particles. Morphological description parameters can be determined according to the geometrical evaluation of the natural manganese dendrites which are formed independently from the process. The formation of manganese dendrites may also explain the stochastic selected process in the nature. These results therefore may be useful to understand the deposits in quartz vein parameters in geophysics.

Tourmaline as a recorder of ore-forming processes

USGS Publications Warehouse

Slack, John F.; Trumbull, Robert B.

2011-01-01

Tourmaline occurs in diverse types of hydrothermal mineral deposits and can be used to constrain the nature and evolution of ore-forming fl uids. Because of its broad range in composition and retention of chemical and isotopic signatures, tourmaline may be the only robust recorder of original mineralizing processes in some deposits. Microtextures and in situ analysis of compositional and isotopic variations in ore-related tourmaline provide valuable insights into hydrothermal systems in seafl oor, sedimentary, magmatic, and metamorphic environments. Deciphering the hydrothermal record in tourmaline also holds promise for aiding exploration programs in the search for new ore deposits.

Spatial evolution of Zn-Fe-Pb isotopes of sphalerite within a single ore body: A case study from the Dongshengmiao ore deposit, Inner Mongolia, China

NASA Astrophysics Data System (ADS)

Gao, Zhaofu; Zhu, Xiangkun; Sun, Jian; Luo, Zhaohua; Bao, Chuang; Tang, Chao; Ma, Jianxiong

2018-01-01

Analyses of sphalerite minerals from the characteristic brecciated Zn-Pb ores of the main ore body in the giant Dongshengmiao deposit have revealed variations in δ66Zn from 0.17 to 0.40‰ and in δ56Fe from -1.78 to -0.35‰. Further, the investigated pyrrhotite samples have iron that is isotopically similar to that of associated sphalerite minerals. The most distinctive pattern revealed by the zinc and iron isotope data is the lateral trend of increasing δ66Zn and δ56Fe values from southwest to northeast within the main ore body. The lead isotopic homogeneity of ore sulfides from the main ore body suggests that there is only one significant source for metal, thus precluding the mixing of multiple metal sources as the key factor controlling spatial variations of zinc and iron isotopes. The most likely control on spatial variations is Rayleigh fractionation during hydrothermal fluid flow, with lighter Zn and Fe isotopes preferentially incorporated into the earliest sulfides to precipitate from fluids. Precipitations of sphalerite and pyrrhotite have played vital roles in the Zn and Fe isotopic variations, respectively, of the ore-forming system. Accordingly, the larger isotopic variability for Fe than Zn within the same hydrothermal system perhaps resulted from a larger proportion of precipitation for pyrrhotite than for sphalerite. The lateral trend pattern revealed by the zinc and iron isotope data is consistent with the occurrence of a cystic-shaped breccia zone, which is characterized by marked elevation in Cu. The results further confirm that Zn and Fe isotopes can be used as a vectoring tool for mineral prospecting.

Fluid inclusion, rare earth element geochemistry, and isotopic characteristics of the eastern ore zone of the Baiyangping polymetallic Ore district, northwestern Yunnan Province, China

NASA Astrophysics Data System (ADS)

Feng, Caixia; Bi, Xianwu; Liu, Shen; Hu, Ruizhong

2014-05-01

The Baiyangping Cu-Ag polymetallic ore district is located in the northern part of the Lanping-Simao foreland fold belt, which lies between the Jinshajiang-Ailaoshan and Lancangjiang faults in western Yunnan Province, China. The source of ore-forming fluids and materials within the eastern ore zone were investigated using fluid inclusion, rare earth element (REE), and isotopic (C, O, and S) analyses undertaken on sulfides, gangue minerals, wall rocks, and ores formed during the hydrothermal stage of mineralization. These analyses indicate: (1) The presence of five types of fluid inclusion, which contain various combinations of liquid (l) and vapor (v) phases at room temperature: (a) H2O (l), (b) H2O (l) + H2O (v), (c) H2O (v), (d) CmHn (v), and (e) H2O (l) + CO2 (l), sometimes with CO2 (v). These inclusions have salinities of 1.4-19.9 wt.% NaCl equivalents, with two modes at approximately 5-10 and 16-21 wt.% NaCl equivalent, and homogenization temperatures between 101 °C and 295 °C. Five components were identified in fluid inclusions using Raman microspectrometry: H2O, dolomite, calcite, CH4, and N2. (2) Calcite, dolomitized limestone, and dolomite contain total REE concentrations of 3.10-38.93 ppm, whereas wall rocks and ores contain REE concentrations of 1.21-196 ppm. Dolomitized limestone, dolomite, wall rock, and ore samples have similar chondrite-normalized REE patterns, with ores in the Huachangshan, Xiaquwu, and Dongzhiyan ore blocks having large negative δCe and δEu anomalies, which may be indicative of a change in redox conditions during fluid ascent, migration, and/or cooling. (3) δ34S values for sphalerite, galena, pyrite, and tetrahedrite sulfide samples range from -7.3‰ to 2.1‰, a wide range that indicates multiple sulfur sources. The basin contains numerous sources of S, and deriving S from a mixture of these sources could have yielded these near-zero values, either by mixing of S from different sources, or by changes in the geological

Geology of the Ralston Buttes district, Jefferson County, Colorado: a preliminary report

USGS Publications Warehouse

Sheridan, Douglas M.; Maxwell, Charles H.; Albee, Arden L.; Van Horn, Richard

1956-01-01

The Ralston Buttes district in Jefferson County is one of the most significant new uranium districts located east of the Continental Divide in Colorado. The district is east of the Colorado Front Range mineral belt, along the east front of the range. From November 1953 through October 1956, about 10,000 tons of uranium ore, much of which was high-grade pitchblende-bearing vein material, was shipped from the district. The ore occurs in deposits that range in size from bodies containing less than 50 tons to ore shoots containing over 1,000 tons. The only other mining activity in the area has been a sporadic production of beryl, feldspar, and scrap mica from Precambrian pegmatites, and quarrying of dimension stone, limestone, and clay from sedimentary rocks. Most of the Ralston Buttes district consists of complexly folded Precambrian metamorphic and igneous rocks - gneiss, schist, quartzite, amphibolite, and granodiorite. Paleozoic and Mesozoic sedimentary rocks crop out in the northeastern part of the district. These rocks are cut by northwesterly-trending fault systems of Laramide age and by small bodies of intrusive rocks that are Tertiary in age. The typical uranium deposits in the district are hydrothermal veins occupying openings in Laramide fault breccias or related fractures that cut the Precambrian rocks. Pitchblende and lesser amounts of secondary uranium minerals are associated with sparse base-mental sulfides in a gangue of carbonate minerals, potash feldspar, and, more rarely, quartz. Less common types of deposits consist of pitchblende and secondary uranium minerals that occupy fractures cutting pegmatites and quartz veins. The uranium deposits are concentrated in two areas, the Ralston Creek area and the Golden Gate Canyon area. The deposits in the Ralston Creek area are located along the Rogers fault system, and the deposits in the Golden Gate Canyon area are along the Hurricane Hill fault system. Two geologic factors were important to the localization

Geology and timing of mineralization at the Cangshang gold deposit, north-western Jiaodong Peninsula, China

USGS Publications Warehouse

Zhang, X.; Cawood, Peter A.; Wilde, S.A.; Liu, R.; Song, H.; Li, W.; Snee, L.W.

2003-01-01

The Cangshang gold deposit of the northwestern Jiaodong Peninsula contains reserves of greater than 50 tonnes (t) and is developed by the largest open pit gold mine in China. This deposit is a Jiaojia-style (i.e. disseminated-and-veinlet) deposit. It is controlled by the San-Cang fault zone, which trends ???040?? and dips 40-75??SE at the mine site. The main (no. 1) orebody lies between a hanging wall of Precambrian metamorphic rocks (mainly amphibolite) of the Fenzishan Group and a footwall composed of the Mesozoic Linglong granitoid. The ore zone is mainly composed of pyritized, sericitized and silicified granitoid, which has undergone variable degrees of cataclasis. SHRIMP U-Pb dating of zircon indicates that the protolith of the hanging wall amphibolite was formed at 2530 ?? 17 Ma and underwent metamorphism at 1852 ?? 37 Ma. The footwall granodiorite has been dated at 166 ?? 4 Ma, whereas zircons from the ore zone yield a younger age of 154 ?? 5 Ma. Cathodoluminescence images of zircons from the granodiorite and ore zone show oscillatory zonation indicative of an igneous origin for both and the ages of these zircons, therefore, are all interpreted to be representative of magmatic crystallization. Dating of sericite by 40Ar-39Ar has been used to directly determine the timing of formation of the Cangshang deposit, providing the first time absolute age on formation of the Jiaojia-style gold deposits. The well-defined age of 121.3 ?? 0.2 Ma provides the precise timing of gold mineralization at the Cangshang deposit. This age is consistent with those of Linglong-style (vein type) gold mineralization, also from the north-western Jiaodong Peninsula, at between 126 and 120 Ma. Therefore, our work indicates that both styles of gold deposits in the Jiaodong Peninsula were formed during the same mineralization event.

New data on the substantial composition of Kalba rare metal deposits

NASA Astrophysics Data System (ADS)

Oitseva, T. A.; Dyachkov, B. A.; Vladimirov, A. G.; Kuzmina, O. N.; Ageeva, O. V.

2017-12-01

Geotectonic position, features of the geological structure and rare metal specialization of the Kalba-Narym granitoid belt formed in the Hercynian cycle in the postcollision (orogenic) geodynamic situation are considered. A geological-genetic model for the formation of the leading type of rare-metal pegmatite deposits (Ta, Nb, Be, Li, etc.) is presented. They are spatially and genetically related mainly to the granitoids of the 1st phase of the Kalba complex, P1 (Bakennoye, Jubilee, Belaya Gora, etc.). The rhythmically pulsating orientation of the process of pegmatite formation with the introduction of ore-bearing fluids (H2O, F, B, Cl, Ta, Nb, Be, etc.) is emphasized from the intracamera focus of a semi-closed magmatic system. The preferred location of ore pegmatite veins in granitoids of moderate basicity occupying an intermediate position in the petrochemical composition between normal granites and granodiorites geochemically specialized in Li, Rb, Cs, Sn, Nb, Ta. The leading ore-controlling role of the latitudinal deep faults of the ancient site in the distribution of rare-metal ore fields and deposits (Ognevsk-Bakennoye, Asubulak, Belogorsk, etc.) is determined. There is a zonal structure of pegmatite veins, a gradual development of mineral complexes from the graphic and oligoclase-microcline (non-ore) to microcline-albite and color albite-spodumene (ore). The mineralization of pegmatite veins is determined by the degree of intensity of the manifestation in them of metasomatic processes (microclinization, alibitization, greisenization, spodumenization, tourmalinization, etc.) and the identification of the main ore minerals (tantalite-columbite, cassiterite, spodumene and beryl). The diversity of the material composition of rare-metal pegmatites containing many unique minerals (cleavelandite, lepidolite, ambligonite, color tourmaline, spodumene, pollucite, etc.) is reflected, which brings them closer to the pegmatite deposits of foreign countries (Koktogai

Water quality data at selected sites in the Mississippi Valley-type Zn-Pb ore district of upper Silesia, Poland, 1995-97

USGS Publications Warehouse

Wirt, Laurie; Motyka, Jacek; Leach, David; Sass-Gustkiewicz, Maria; Szuwarzynski, Marek; Adamczyk, Zbigniew; Briggs, Paul; Meiers, Al

2003-01-01

The water chemistry of aquifers and streams in the Upper Silesia Ore District, Poland are affected by their proximity to zinc, lead, and silver ores and by ongoing mining activities that date back to the 11th century. This report presents hydrologic and water-quality data collected as part of a collaborative research effort of the U.S. Geological Survey and the University of Mining and Metallurgy in Cracow, Poland to study Mississippi-Valley-Type lead-zinc deposits. MVT deposits in the Upper Silesia Ore District (Fig. 1) were selected for detailed study because the Polish mining industry allowed access to collect samples from underground mines and mine-land property. Water-quality samples were collected from streams, springs, wells, underground mine seeps and drains; and mine-tailings ponds. Data include field measurements of specific conductance, pH, water temperature, and dissolved oxygen and laboratory analyses of major and minor inorganic constituents and selected trace-element constituents.

Host-rock controlled epigenetic, hydrothermal metasomatic origin of the Bayan Obo REEFe-Nb ore deposit, Inner Mongolia, P.R.C.

USGS Publications Warehouse

Chao, E.C.T.; Back, J.M.; Minkin, J.A.; Yinchen, R.

1992-01-01

Bayan Obo, a complex rare earth element (REE)FeNb ore deposit, located in Inner Mongolia, P.R.C. is the world's largest known REE deposit. The deposit is chiefly in a marble unit (H8), but extends into an overlying unit of black shale, slate and schist unit (H9), both of which are in the upper part of the Middle Proterozoic Bayan Obo Group. Based on sedimentary structures, the presence of detrital quartz and algal fossil remains, and the 16-km long geographic extent, the H8 marble is a sedimentary deposit, and not a carbonatite of magmatic origin, as proposed by some previous investigators. The unit was weakly regionally metamorphosed (most probably the lower part of the green schist facies) into marble and quartzite prior to mineralization. Tectonically, the deposit is located on the northern flank of the Sino-Korean craton. Many hypotheses have been proposed for the origin of the Bayan Obo deposit; the studies reported here support an epigenetic, hydrothermal, metasomatic origin. Such an origin is supported by field and laboratory textural evidence; 232Th/208Pb internal isochron mineral ages of selected monazite and bastnaesite samples; 40Ar/39Ar incremental heating minimum mineral ages of selected alkali amphiboles; chemical compositions of different generations of both REE ore minerals and alkali amphiboles; and evidence of host-rock influence on the various types of Bayan Obo ores. The internal isochron ages of the REE minerals indicate Caledonian ages for various episodes of REE and Fe mineralization. No evidence was found to indicate a genetic relation between the extensive biotite granitic rocks of Hercynian age in the mine region and the Bayan Obo are deposit, as suggested by previous workers. ?? 1992.

Deep Ore-controlling Role Beneath the Collision-related Deposit Zone in South Tibetan Plateau, Preliminary Results Revealed by Magnetotelluric Data

NASA Astrophysics Data System (ADS)

Xie, C.; Jin, S.; Wei, W.; Ye, G.; Fang, Y.; Zhang, L.; Dong, H.; Yin, Y.

2017-12-01

The Tibetan plateau is the largest and most recent plateau orogenic belt in the world, and the south part is expected as the ongoing India-Eurasia continental collision zone. The collision-related deposit zones which are distributed in south plateau could be roughly divided into three parts: the porphyry deposit in the Gangdese magmatic belt, the chromite deposit along the Yarlung-Zangbo suture (YZS) and the prospective deposit along the gneiss domes in the Tethys Himalayan. The deep ore-controlling role of those deposit zones is still remain controversial. Previous magnetotelluric (MT) data deployed from Himalayan to Gangdese terrane were inverted using a three dimensional (3D) MT inversion algorithm ModEM. The results show that the resistivity cover layers above -10 km are distributed along the whole profiles, whereas small and sporadic conductors could be also imaged. The middle to lower crust beneath -25 km is imaged as large scale but discontinuous conductive zones which have a central resistivity less than 10 ohm·m. We suggest the middle to lower crustal conductors could be interpreted as partial melting. This hypothesis is supported by some previous geological and geochemical studies. The Metallogenesis and partial melting play an important role in promoting each other. For the metallogenesis, the high water content is one of the prominent factors, and could be released on breakdown of amphibole in eclogite and garnet amphibolite during melting. On the other hand, the increasing of the water content would probably advance partial melting. The results indicate that the deep process and magmatism beneath different deposit zones are probably varying. We studied the rheological characteristics from the perspective of subsurface electrical structures. We hope by comparative analysis, the process of `origins - migration -formation' for the system of deep `magma - rheology - deposition' would be better understood.

Sedimentary exhalative nickel-molybdenum ores in south China

USGS Publications Warehouse

Lott, D.A.; Coveney, R.M.; Murowchick, J.B.; Grauch, R.I.

1999-01-01

Unique bedded Ni-Mo ores hosted by black shales were discovered in localized paleobasins along the Yangzte platform of southern China in 1971. Textural evidence and radiometric dates imply ore formation during sedimentation of black shales that grade into readily combustible beds, termed stone coals, which contain 10 to 15 percent organic carbon. Studies of 427 fluid inclusions indicate extreme variation in hydrothermal brine salinities that were contained by Proterozoic dolostones underlying the ore zone in Hunan and Guizhou. Variations of fluid inclusion salinities, which range from 0.1 to 21.6 wt percent NaCl equiv, are attributed to differences in the compositions of brines in strata underlying the ore bed, complicated by the presence of seawater and dilute fluids that represent condensates of vapors generated by boiling of mineralizing fluids or Cambrian meteoric water. The complex processes of ore deposition led to scattered homogenization temperatures ranging from 100??to 187??C within the Hunan ore zone and from 65??to 183??C within the Guizhou ore zone. While living organisms probably did not directly accumulate metals in situ in sufficient amounts to explain the unusually high grades of the deposits, sulfur isotope ratios indicate that bacteria, now preserved as abundant microfossils, provided sufficient sulfide for the ores by reduction of seawater sulfate. Such microbiota may have depended on vent fluids and transported organic matter for key nutrients and are consistent with a sedex origin for the ores. Vent fluids interacted with organic remains, including rounded fragments of microbial mats that were likely transported to the site of ore deposition by the action of waves and bottom currents prior to replacement by ore minerals.

Geology and mineral deposits of the Hekimhan-Hasancelebi iron district, Turkey

USGS Publications Warehouse

Jacobson, Herbert S.; Kendiro'glu, Zeki; ,; Celil, Bogaz; ,; Onder, Osman; Gurel, Nafis

1972-01-01

An area of 210 sq km was investigated in the Hekimhan-Hasancelebi district. of central Turkey as part of the Maden Tetkik ve Arama Institusu(MTA)-U. S. Geological Survey(USGS) mineral exploration and training project to explore for iron deposits and to provide on-.the-job training for MTA geologists. The rocks of the area are Cretaceous and Tertiary sedimentary and volcanic rocks intruded by syenite and a serpentinized mafic and ultramafic complex and overlain unconformably by late .Tertiary basalt. The base of the section is a thick mafic volcanic-sedimentary sequence with diverse rocks that include conglomerate, sandstone, shale, tuff, limestone, and basalt. The upper part of the sequence is metasomatized near syenite contacts. The sequence is conformably overlain by trachyte and unconformably overlain by massive limestone. Overlying the limestone is a Tertiary sedimentary sequence which is dominantly conglomerate and sandstone with local limestone and volcanic rocks. This series is in turn overlain by olivine basalt. Mineral deposits are associated with the two types of intrusive rocks. Hematite-magnetite in the Karakuz mine area and in the Bahcedami-Hasancelebi area is related to the syenite, and siderite in the Deveci mine area is possibly related to the mafic-ultramafic rocks. Significant iron resources are found, only in the Karakuz and Deveci areas. In the Karakuz area disseminations, veins, and replacements consisting of hematite and magnetite are present. Most of the material is low grade. In the Deveci mine area a large deposit of siderite apparently is a replacement of carbonate beds adjacent to serpentinized igneous rock. The upper part of the siderite deposit is weathered and enriched to a mixture of iron and manganese oxides of direct shipping ore grade. Additional investigation of both the Karakuz and .Deveci mine areas is recommended including: 1. A detailed gravity and magnetic survey of part of the Karakuz area. 2. Diamond drilling at both the

Prediction of ore fluid metal concentrations from solid solution concentrations in ore-stage calcite: Application to the Illinois-Kentucky and Central Tennessee Mississippi Valley-type districts

NASA Astrophysics Data System (ADS)

Smith-Schmitz, Sarah E.; Appold, Martin S.

2018-03-01

, which like Pb also have a divalent ionic radius larger than that of Ca2+ and form carbonate minerals with the aragonite structure, did not consistently agree well with known concentrations of Sr and Ba in fluid inclusions. The ore fluid Zn concentrations predicted in the present study lie within the range of Zn concentrations typical of modern sedimentary brines and are high enough to allow deposition of the observed amounts of Zn in the Illinois-Kentucky and Central Tennessee districts within ranges of geologically reasonable times and ore fluid flow velocities. If the pH of the Illinois-Kentucky and Central pH ore fluids was as low as current evidence suggests to be possible, then these ore fluids could simultaneously have transported enough sulfide with their Zn to account for the observed amounts of sphalerite in the districts.

Isotope and Chemical Methods in Support of the U.S. Geological Survey Science Strategy, 2003-2008

USGS Publications Warehouse

Rye, R.O.; Johnson, C.A.; Landis, G.P.; Hofstra, A.H.; Emsbo, P.; Stricker, C.A.; Hunt, A.G.; Rusk, B.G.

2008-01-01

Principal functions of the Mineral Resources Program are providing information to decision-makers related to mineral deposits on federal lands and predicting the environmental consequences of the mining or natural weathering of those deposits. Performing these functions requires that predictions be made of the likelihood of undiscovered deposits. The predictions are based on geologic and geoenvironmental models that are constructed for the various types of mineral deposits from detailed descriptions of actual deposits and detailed understanding of the processes that formed them. Over the past three decades the understanding of ore-forming processes has benefitted greatly from the integration of laboratory-based geochemical tools with field observations and other data sources. Under the aegis of the Evolution of Ore Deposits and Technology Transfer Project (EODTTP), a five-year effort that terminated in 2008, the Mineral Resources Program provided state-of-the-art analytical capabilities to support applications of several related geochemical tools.

Rhenium in ores of the Mikheevskoe porphyry Cu-Mo deposit, South Urals

NASA Astrophysics Data System (ADS)

Plotinskaya, O. Yu.; Grabezhev, A. I.; Seltmann, R.

2015-03-01

The distribution of Re in ores of the Mikheevskoe Mo-Cu deposit in the South Urals is studied. It is established that the grade of Re in the ores usually does not exceed 0.5 g/t. A positive correlation between concentrations of Re and Mo (correlation coefficient 0.94), and Re and Cu (correlation coefficient 0.52) is found. EMPA of individual flakes of molybdenite showed that a Re content higher than the detection limit has been measured in most flakes studied, as a rule as high as 0.4-0.5 wt %, but occasionally reaching 1.34 wt %. Re within flakes of molybdenite is irregularly distributed. Patchy, linear, and concentric-zoned patterns of zones with elevated Re content (usually 0.5-1 wt % Re, sometimes higher) are found against the lower content (up to 0.2 wt % Re) that is regularly distributed within the flake. Later hydrothermal processes and mechanical deformation of flakes result in epigenetic Re redistribution in molybdenite that leads to homogenization of molybdenite composition and smoothing of primary pattern, or removal of Re from molybdenite.

Zircon U-Pb and molybdenite Re-Os geochronology and geological significance of the Baoshan porphyry Cu polymetallic deposit in Jiangxi province

NASA Astrophysics Data System (ADS)

Jia, Liqiong; Wang, Liang

2017-10-01

Baoshan porphyry Cu polymetallic deposit belongs to Jiujiang-Ruichang Cu-Au ore field, which is a component part of the Middle-Lower Yangtze River Cu-Au metallogenic belt. The U-Pb LA-MC-TCP MS dating of the zircons from Baoshan granodiorite porphyry yields an age of 147.81±0.48Ma (MSWD=1.07). Six molybdenite samples separated from Baoshan deposit are used for Re-Os dating and obtained the weighted average age of 147.42±0.84Ma and an isochron age of 147.7±1.2Ma. These ages suggest that the mineralization in the Baoshan deposit is genetically associated to the granodiorite porphyry, and the process of rock-and ore-forming is continuous. These data indicate that ages of intrusion and ore-body from Baoshan deposit are almost identical to other typical magmatic intrusion and deposits in Jiujiang-Ruichang metallogenic district. Tt is inferred that the Baoshan deposit was formed in the transition from EW-striking Tndosinian tectonic domain to NE-striking Paleo-Pacific tectonic domain.

The copper-cobalt deposits of the Quartzburg district, Grant County, Oregon

USGS Publications Warehouse

Vhay, John Stewart

1960-01-01

The copper- and cobalt-bearing veins of part of the Quartzburg district are in fracture zones trending about N. 70 degrees E. in folded Permian (?) metavolcanic rocks on the southwest side of a quartz diorite stock. Along many of the veins fine-grained tourmaline and quartz have replaced the country rock. The primary ore minerals are chalcopyrite, glaucodot, safflorite, and cobaltite. The copper- and cobalt-rich parts of the deposits appear to be in separate ore shoots. Gold content is generally higher in the cobalt-bearing parts of the veins than in the copper-rich parts. The Standard mine has developed part of one vein zone. Several other vein zones that crop out may contain as much copper as the Standard vein zone. Further bulldozing and diamond drilling on the surface, and more geologic mapping, sampling, and diamond drilling underground are suggested as means to explore for more ore deposits.

Chromite deposits of the north-central Zambales Range, Luzon, Philippines

USGS Publications Warehouse

Rossman, D.L.

1970-01-01

of ores, association of chromite with dunite as gangue and as halos, and the transecting nature of the layering, foliation, and lineation in relation to chromite, are similar in all deposits regardless of composition of the chromite mineral itself. Textures in chromite ores, and structural relationships between chromite deposits and country rocks, show that layering and related foliation and lineation were formed or modified by flowage. Gabbro is believed to form the upper part of the Complex in general. Geophysical methods have been rather unsuccessful in finding chromite in the Zambales Complex. Gravity surveys, in order to be successful, must correct for all features influencing gravity except for the chromite itself. Too often the uncertainties in position of rock units and in knowledge of rock densities or position of hidden geologic features (dikes, zones of alteration) preclude the possibility of making adequate corrections. Magnetic surveys have failed to reveal any magnetic patterns attributable to the presence of chromite. Exploration for chromite should be guided by the knowledge that chromite occurs only in certain geologic environments. Thus because nearly all known chromite deposits in the Zambales Complex lie in peridotite near the gabbro contact, search for chromite should be concentrated there. Likewise it is evident from structural evidence presented here that there is little relation between layering and distribution of either major rock units or chromite deposits. Thus one is not justified in using the layered structure to predict either the position or attitude of major rock unit contacts, or presence or position of chromite deposits. In such a productive complex it is geologically certain that unknown deposits still remain undiscovered. The most promising areas for exploration are near known groups of large deposits like Acoje and Chromite Reservation No. 1. Underground drilling has been very successful in finding buried tabular

Intriguing Connections Between Economic Geology, the Environment, Human Health, and Disasters: Observations from my Career(s) in Transdisciplinary Science

NASA Astrophysics Data System (ADS)

Plumlee, G. S.

2015-12-01

I have been fortunate to be able to follow a varied career path from economic geology, to environmental geochemistry, to geochemistry and human health, to environmental disasters. I have been privileged to collaborate with many exceptional scientists from across and well beyond the earth sciences (e.g., public heath, engineering, economics, emergency response, microbiology). Much of this transdisciplinary work has intriguing links back to economic geology/geochemistry. Geological characteristics of different ore deposit types predictably influence the environmental and health impacts of mining, and so can help anticipate and prevent adverse impacts before they occur. Geologic maps showing potential for natural occurrences of asbestos or erionite are analogous to permissive tract maps used for mineral-resource assessments, and can be correlated with epidemiological data to help understand whether living on or near such rocks poses a risk for developing asbestos-related diseases. Mineral particles that are taken up by the human body along inhalation or incidental ingestion exposure routes are "weathered" by reactions with diverse body fluids that differ greatly in composition between and along the different exposure routes. These in vivo chemical reactions (e.g., dissolution, alteration, metal complexation, oxidation/reduction, reprecipitation) are in ways analogous to processes of ore deposit formation and weathering, and some can be shown (in collaboration with toxicologists) to play a role in toxicity. Concepts of ore petrography and paragenesis can be applied to interpret (in collaboration with pathologists) the origin, physiological implications, and toxicity effects of mineral matter in human tissue samples obtained by biopsy, transplant or autopsy. Some disaster materials can originate from mining- or mineral-processing sources, and methods originally developed to study ore deposits or mining-environmental issues can also be applied to understand many disaster

Geostatistical Approach to Estimating the Gold Ore Characteristics and Gold Reserves: A Case Study Daksa Area, Quang Nam Province, Viet Nam

NASA Astrophysics Data System (ADS)

Luan Truong, Xuan; Luong Le, Van; Quang Truong, Xuan

2015-04-01

Daksa gold deposit is the biggest gold deposits in Vietnam. The Daksa geological structure complicated, distributed mainly metamorphosed sedimentary NuiVu formation (PR3-?1nv2). The sulfide gold ore bodies distributed in quartz schist, quartz - biotite related to faut and distribution wing anticline. The gold ore bodies form circuits, network circuits, circuits lenses; fill the cup surface layer of the developing northeast - southwest; is the less than or west longitude north - SE. The results show that, Au and accompanying elements (Ag, Pb and Zn) have correlated pretty closely. All of its consistent with the logarithmic distribution standard, in accordance with the law of distribution of content mineral rare. The structure functions have nugget effect and spherical models with show that Au and accompanying elements special variation are changes. Au contents shown local anisotropy, no clearly anisotropy (K=1,17) and weakly anisotropy (K=1,4). Intensity mineralization of the ore bodies are quite high with demand spherical conversion coefficient ranging from 0.49 to 0.75 and from 0.66 to 0.97 (for other body). With nugget effects, ore bodies shown that it is consistent with mineralization in the ore bodies study, ore erasable, micro vein, infilling fractures in quartz vein. All of variogram presents local anisotropy, indicated gold mineralization at study area has least two-mineralization stages, consistent with the analysis of mineralography samples. By the results of the structure function study, the authors present the system optimization for exploration deposit and used to evaluate gold reserves by Ordinary Kriging. High accuracy of Kriging estimation results are expressed in the minimum Kriging variance, by compare the results calculated by some other methods (such as distance inverse weighting method, ..) and specially compare to the results of a some blocks have been exploited. Key words: Geostat and gold deposits VN. Daksa and gold mineralization. Geostat

Understanding Cu release into environment from Kure massive sulfide ore deposits, Kastamonu, NW Turkey

NASA Astrophysics Data System (ADS)

Demirel, Cansu; Sonmez, Seref; Balci, Nurgul

2014-05-01

Covering a wide range on the earth's crust, oxidation of metal sulfide minerals have vital environmental impacts on the aquatic environment, causing one of the major environmental problems known as acid mine drainage (AMD). Located in the Kastamonu province of the Western Black Sea region, Kure district is one of the major copper mining sites in Turkey. Mining activities in the area heads back to ancient times, such that operation is thought to be started with the Roman Empire. Currently, only the underground mining tunnels of Bakibaba and Asikoy are being operated. Thus, mining heaps and ores of those pyritic deposits have been exposed to the oxidative conditions for so long. As a result of weathering processes of past and recent heaps of the Kure volcanic massive sulfide deposits in addition to the main ore mineral (chalcopyrite), significant amount of metals, especially Cu, are being released into the environment creating undesirable environmental conditions. In order to elucidate Cu release mechanisms from Kure pyritic ore deposits and mining wastes, field and laboratory approaches were used. Surface water and sediment samples from the streams around the mining and waste sites were collected. Groundwater samples from the active underground mining site were also collected. Physical parameters (pH, Eh, T°C, and EC) of water samples were determined in situ and in the laboratory using probes (WTW pH 3110, WTW Multi 9310 and CRISON CM 35). Metal and ion concentrations of the water samples were analysed using ICP-MS and DR 2800 spectrophotometer, respectively. High Cu, Co, Zn and Fe concentrations were determined in the water samples with pH values ranging from 2.9- 4. Cu concentrions ranges from 345 ppm to 36 ppm in the water samples. Consistent with the water samples, high Cu, Fe, Zn and Co were also determined in the sediment samples. Laboratory chalcopyrite oxidation experiments under the conditions representing the field site were set up as biological and

Fluid mixing and ore deposition during the geodynamic evolution of the Sierra Almagrera (Betics, Spain)

NASA Astrophysics Data System (ADS)

Dyja, Vanessa; Tarantola, Alexandre; Hibsch, Christian; Boiron, Marie-Christine; Cathelineau, Michel

2013-04-01

Marine and continental intramountaineous basins developed during the Neogene orographic evolution of the Betico-rifan orogenic wedge, as well as the related uplifted ranges within the Sierra Almagrera Metamorphic Core Complexes (MCC). The NNE-SSW striking trans-Alboran transcurrent fault system crosscuts the MCC post-dating the extensional exhumation stages recorded in the metamorphic fabric. Iron ores (± Pb, Cu, Zn) are encountered either as stratabound ore deposits in the Neogene basins or as vein networks crosscutting the metamorphic fabric of graphitic phyllites from the Sierra Almagrera. These Late Miocene ore deposits are related to the activity of the N-S striking Palomares fault segment of the Trans-Alboran fault system. Three sets of quartz veins (Vα, Vαβ and Vβ) and one set of mineralized vein (Vγ, siderite, barite) are distinguished. The Vα and Vαβ respectively are totally or partially transposed into the foliation. The Vβ and Vγ veins are discordant to the foliation. The problem addressed in this study concerns the nature of the fluids involved in the metal deposits and their relationships with the main reservoir fluids, e.g. the deep metamorphic fluids, the basinal fluids, and eventually the recharge meteoric fluids. This study focuses thus on the evolution of the fluids at different stages of ductile-brittle exhumation of the metamorphic ranges (Sierras) and their role during the exhumation and later on in relation with the hydrothermalism and metal deposition at a regional scale. Paleofluids were studied as inclusions in quartz, siderite and barite from veins by microthermometry and Raman spectroscopy, and a stable isotope study is in progress. Earliest fluids recorded in (Vαβ) quartz veins are H2O- NaCl + CaCl2 (17 wt. %) - (traces of CO2, CH4, N2) metamorphic brines trapped at the ductile brittle transition at a minimum trapping temperatures (Th) of 340 °C. Older metamorphic fluids in (Vα) veins were lost during the complete

Volcanogenic massive sulphide and orogenic gold deposits of northern southeast Alaska

USGS Publications Warehouse

Sack, Patrick J; Karl, Susan M.; Steeves, Nathan; Gemmell, J Bruce

2016-01-01

This five-day field trip visits the most significant mineral deposits in northern southeast Alaska. The trip begins and ends with regional transects in the interior Intermontane terranes around Whitehorse, Yukon, and the Insular terranes along the northern Chatham Strait region of southeast Alaska (Fig. A-1 and Fig. A-2; Plate-1). To put the deposits in a regional tectonic framework, the guidebook begins with an introduction to northern Cordilleran geology, tectonics and metallogeny. The foci of the deposit portion of the field trip are Late Triassic volcanogenic massive sulphide (VMS) deposits of the Alexander Triassic metallogenic belt and Paleogene orogenic gold deposits of the Juneau gold belt. Details of the local geology are further elaborated in each segment of the guide book (Days 1-5). The data that provide the basis for the VMS deposit interpretations come from a series of PhD and MSc studies by the Centre of Excellence in Ore Deposit Research (CODES) at the University of Tasmania and the University of Ottawa. These deposit-scale studies are complimented by a long history of regional mapping and research by the U.S. Geological Survey (USGS).

Application of a feedforward neural network in the search for kuroko deposits in the Hokuroku District, Japan

USGS Publications Warehouse

Singer, Donald A.; Kouda, Ryoichi

1996-01-01

A feedforward neural network with one hidden layer and five neurons was trained to recognize the distance to kuroko mineral deposits. Average amounts per hole of pyrite, sericite, and gypsum plus anhydrite as measured by X-rays in 69 drillholes were used to train the net. Drillholes near and between the Fukazawa, Furutobe, and Shakanai mines were used. The training data were selected carefully to represent well-explored areas where some confidence of the distance to ore was assured. A logarithmic transform was applied to remove the skewness of distance and each variable was scaled and centered by subtracting the median and dividing by the interquartile range. The learning algorithm of annealing plus conjugate gradients was used to minimize the mean squared error of the scaled distance to ore. The trained network then was applied to all of the 152 drillholes that had measured gypsum, sericite, and pyrite. A contour plot of the neural net predicted distance to ore shows fairly wide areas of 1 km or less to ore; each of the known deposit groups is within the 1 km contour. The high and low distances on the margins of the contoured distance plot are in part the result of boundary effects of the contouring algorithm. For example, the short distances to ore predicted west of the Shakanai (Hanaoka) deposits are in basement. However, the short distances to ore predicted northeast of Furotobe, just off the figure, coincide with the location of the Nurukawa kuroko deposit and the Omaki deposit, south of the Shakanai-Hanaoka deposits, seems to be on an extension of short distance to ore contour, but is beyond the 3 km limit from drillholes. Also of interest are some areas only a few kilometers from the Fukazawa and Shakanai groups of deposits that are estimated to be many kilometers from ore, apparently reflecting the network's recognition of the extreme local variability of the geology near some deposits.

Geochemical contrasts between Late Triassic ore-bearing and barren intrusions in the Weibao Cu-Pb-Zn deposit, East Kunlun Mountains, NW China: constraints from accessory minerals (zircon and apatite)

NASA Astrophysics Data System (ADS)

Zhong, Shihua; Feng, Chengyou; Seltmann, Reimar; Li, Daxin; Dai, Zhihui

2017-12-01

The Weibao copper-lead-zinc skarn deposit is located in the northern East Kunlun terrane, NW China. Igneous intrusions in this deposit consist of barren diorite porphyry (U-Pb zircon age of 232.0 ± 2.0 Ma) and ore-bearing quartz diorite and pyroxene diorite (U-Pb zircon ages of 223.3 ± 1.5 and 224.6 ± 2.9 Ma, respectively). Whole-rock major and trace element and accessory mineral (zircon and apatite) composition from these intrusions are studied to examine the different geochemical characteristics of ore-bearing and barren intrusions. Compared to the barren diorite porphyry, the ore-bearing intrusions have higher Ce4+/Ce3+ ratios of zircon and lower Mn contents of apatite, indicating higher oxidation state. Besides, apatite from the ore-bearing intrusions shows higher Cl contents and lower F/Cl ratios. These characteristics collectively suggest the higher productivity of ore-bearing quartz diorite and pyroxene diorite. When compared with ore-bearing intrusions from global porphyry Cu deposits, those from Cu-Pb-Zn skarn deposits display lower Ce4+/Ce3+ and EuN/EuN* ratios of zircon and lower Cl and higher F/Cl ratios of apatite. We conclude that these differences reflect a general geochemical feature, and that zircon and apatite composition is a sensitive tool to infer economic potential of magmas and the resulting mineralization types in intrusion-related exploration targets.

Simulation of geochemical processes responsible for the formation of the Zhezqazghan deposit

NASA Astrophysics Data System (ADS)

Ryzhenko, B. N.; Cherkasova, E. V.

2014-05-01

Physicochemical computer simulation of water-rock systems at a temperature of 25-150°C and under a pressure of up to 600 bar has been carried out for quantitative description of the mineralization formation conditions at sandstone- and shale-hosted copper deposits. The simulation is based on geological and geochemical information concerning the Zhezqazghan deposit and considers (i) a source of ore matter, (ii) composition of the fluid that transfers ore matter to the ore formation zone, and (iii) factors of ore concentration. It has been shown that extraction of copper from minerals of rocks and its accumulation in aqueous solution are optimal at a high mass ratio of rock to water (R/W > 10), Eh of +200 to -100 mV, and an obligatory content of chloride ions in the aqueous phase. The averaged ore-bearing fluid Cl95SO44//Ca50(Na + K)30Mg19 (eq %), pH ˜ 4, mineralization of up to 400 g/L, is formed by the interaction of red sandstone beds with a sedimentogenic brine (a product of metamorphism of seawater in carbonate rocks enriched in organic matter). The ore concentration proceeds in the course of cooling from 150 to 50°C during filtration of ore-bearing fluid through red sandstone beds in the rock-water system thermodynamically opened with respect to the reductive components.

Ore deposits and epithermal evidences associated with intra-magmatic faults at Aïn El Araâr-Oued Belif ring structure (NW of Tunisia)

NASA Astrophysics Data System (ADS)

Aissa, Wiem Ben; Aissa, Lassaâd Ben; Amara, Abdesslem Ben Haj; Tlig, Said; Alouani, Rabah

2017-03-01

Hydrothermal ore deposits at Aïn El Araâr-Oued Belif location are classified as epithermal deposits type. The ore bodies are hosted by upper Turonian (8-9 M.y) volcanic rhyodacitic complex. Polymetallic sulfide orebodies are mainly concentrated within intra-magmatic faults. Petrographic, XRD, and TEM-STEM investigations revealed that ore minerals are essentially, arsenopyrite, pyrite, chalcopyrite, pyrrhotite, hematite, goethite and magnetite with Au, Ag and Pt trace metals. Gangue minerals are mainly adularia, quartz, sericite, alunite, tridymite, chlorite, phlogopite and smectite. Epithermal alteration is well zoned with four successive characteristic zones: (1) zone of quartz-adularia-sericite and rare alunite; (2) zone of kaolinite and plagioclase albitization; (3) intermediate zone of illite-sericite; (4) sapropelic alteration type zone of chlorite-smectite and rare illite. This can be interpreted as a telescoping of two different acidity epithermal phases; low sulfidation (adularia-sericite) and high sulfidation (quartz-alunite), separated in time or due to a gradual increase of fluids acidity and oxicity within the same mineralization phase. Brecciated macroscopic facies with fragments hosting quartz-adularia-sericite minerals (low-sulfidation phase) without alunite, support the last hypothesis. Geodynamic context and mineral alteration patterns are closely similar to those of Maria Josefa gold mine at SE of Spain which exhibit a volcanic-hosted epithermal ore deposit in a similar vein system, within rhyolitic ignimbrites, altered to an argillic assemblage (illite-sericite abundant and subordinate kaolinite) that grades outwards into propylitic alteration (Sanger-von Oepen et al. (1990)). Mineralogical and lithologic study undertaken in the volcanic host rock at Aïn El Araâr-Oued Belif reveals a typical epithermal low-sulfidation and high-sulfidation ore deposits with dominance of low-sulfidation. Host rocks in these systems range from silicic to

Geologic map of the Haji-Gak iron deposit, Bamyan Province, Afghanistan, modified from the 1965 original map compilation of M.S. Smirnov and I.K. Kusov

USGS Publications Warehouse

Renaud, Karine M.; Tucker, Robert D.; Peters, Stephen G.; Stettner, Will R.; Masonic, Linda M.; Moran, Thomas W.

2011-01-01

This map is a modified version of Geological-structural map of Hajigak iron-ore deposit, scale 1:10,000, which was compiled by M.S. Smirnov and I.K. Kusov in 1965. (Refer to the References Cited section in the Map PDF for complete citations of the original map and a related report.) USGS scientists, in cooperation with the Afghan Geological Survey and the Task Force for Business and Stability Operations of the U.S. Department of Defense, studied the original documents and also visited the field area in November 2009. This modified map illustrates the geological structure of the Haji-Gak iron deposit and includes cross sections of the same area. The map reproduces the topology (contacts, faults, and so forth) of the original Soviet map and cross sections and includes modifications based on our examination of these documents. Elevations on the cross sections are derived from the original Soviet topography and may not match the newer topography used on the current map. We have attempted to translate the original Russian terminology and rock classification into modern English geologic usage as literally as possible without changing any genetic or process-oriented implications in the original descriptions. We also use the age designations from the original map. The unit colors on the map and cross sections differ from the colors shown on the original version. The units are colored according to the color and pattern scheme of the Commission for the Geological Map of the World (CGMW) (http://www.ccgm.org).

Joint Interpretation of Geological, Magnetic, AMT, and ERT Data for Mineral Exploration in the Northeast of Inner Mongolia, China

NASA Astrophysics Data System (ADS)

Zhang, Gang; Lü, Qing-Tian; Zhang, Gui-Bin; Lin, Ping-Rong; Jia, Zheng-Yuan; Suo, Kui

2018-03-01

The integrated interpretation of data from various technologies has the potential to obtain a more accurate estimate of subterranean earth properties. In this paper, we implement the joint interpretation of geological and geophysical data for mineral exploration in the northeastern region of Inner Mongolia, China. The joint application of several methodologies reduces the exploration risk. We first determined an approximate and large potential area for mineral exploration with geological data and magnetic data interpretation in Gaoerqi. Results from the two types of data analysis show that the ore deposit strikes roughly east in the northern part of the Gaoerqi mining area. Next, we employed the audio-magnetotelluric (AMT) method to study the subterranean electrical resistivity distribution and divide the earth into four layers. Inverted resistivity sections from the AMT data illustrate that the ore deposits are likely developed in the low-resistivity zone of the survey area from the land surface to 300-m depth. Finally, the high-resolution borehole-to-surface electrical resistivity tomography (ERT) method was employed for further investigation of the location and attitude of the potential ore deposits. Inverted resistivity sections from the ERT data show that two prospective areas for mineral exploration were observed in the west of the survey area and that the eastern portion of the survey area warrants further investigation.

Geology of the Anderson Mesa quadrangle, Colorado

USGS Publications Warehouse

Cater, Fred W.; Withington, C.F.

1953-01-01

The Anderson Mesa quadrangle is one of the eighteen 7 1/2-minute quadrangles covering the principal carnotite-producing area of the southwestern Colorado. The geology of these quadrangles was mapped by the U.S. Geological Survey for the Atomic Energy Commission as part of a comprehensive study of carnotite deposits. The rocks exposed in the eighteenth quadrangles consist of crystalline rocks of pre-Cambrian age and sedimentary rocks that range in age from late Paleozoic to Quarternary. Over much of the area the sedimentary rocks are flat lying, but in places the rocks are disrupted by high-angle faults, and northwest-tending folds. Conspicuous among the folds are large anticlines having cores of intrusive slat and gypsum. Most of the carnotite deposits are confined to the Salt Wash sandstone member of the Jurassic Morrison formation. Within this sandstone, most of the deposits are spottily distributed through an arcuate zone known as the "Uravan Mineral Belt". Individual deposits range in size from irregular masses containing many thousands of tons. The ore consists of largely of sandstone selectively impregnated and in part replaced by uranium and vanadium minerals. Most of the deposits appear to be related to certain sedimentary structures in sandstones of favorable composition.

Geology of the Gypsum Gap quadrangle, Colorado

USGS Publications Warehouse

Cater, Fred W.

1953-01-01

The Gypsum Gap quadrangle is one eighteen 7 1/2-minute quadrangles covering the principal carnotite-producing area of southwestern Colorado. The geology of these quadrangles was mapped by the U.S. Geological Survey for the Atomic Energy Commission as part of a comparative study of carnotite deposits. The rocks exposed in the eighteen quadrangles consist of crystalline rocks of pre-Cambrian age and sedimentary rocks that range in age from late Paleozoic to Quaternary. Over much of the area the sedimentary rocks are flat lying, but in places the rocks are disrupted by high-angle faults, and northwest-trending folds. Conspicuous among the folds are large anticlines having cores of intrusive salt and gypsum. Most of the carnotite deposits are confined to the Salt Wash sandstone member of the Jurassic Morrison formation. Within this sandstone, most of the deposits are spottily distributed through a arcuate zone known as the "Uravan Mineral Belt". Individual deposits range in size from irregular masses containing only a few tons of ore to large, tabular masses containing many thousands of tons. The core consists largely of sandstone selectively impregnated and in part replaced by uranium and vanadium minerals. Most of the deposits appear to be related to certain sedimentary structures in sandstones of favorable composition.

Iron isotope fractionation during hydrothermal ore deposition and alteration

NASA Astrophysics Data System (ADS)

Markl, Gregor; von Blanckenburg, Friedhelm; Wagner, Thomas

2006-06-01

Iron isotopes fractionate during hydrothermal processes. Therefore, the Fe isotope composition of ore-forming minerals characterizes either iron sources or fluid histories. The former potentially serves to distinguish between sedimentary, magmatic or metamorphic iron sources, and the latter allows the reconstruction of precipitation and redox processes. These processes take place during ore formation or alteration. The aim of this contribution is to investigate the suitability of this new isotope method as a probe of ore-related processes. For this purpose 51 samples of iron ores and iron mineral separates from the Schwarzwald region, southwest Germany, were analyzed for their iron isotope composition using multicollector ICP-MS. Further, the ore-forming and ore-altering processes were quantitatively modeled using reaction path calculations. The Schwarzwald mining district hosts mineralizations that formed discontinuously over almost 300 Ma of hydrothermal activity. Primary hematite, siderite and sulfides formed from mixing of meteoric fluids with deeper crustal brines. Later, these minerals were partly dissolved and oxidized, and secondary hematite, goethite and iron arsenates were precipitated. Two types of alteration products formed: (1) primary and high-temperature secondary Fe minerals formed between 120 and 300 °C, and (2) low-temperature secondary Fe minerals formed under supergene conditions (<100 °C). Measured iron isotope compositions are variable and cover a range in δ56Fe between -2.3‰ and +1.3‰. Primary hematite ( δ56Fe: -0.5‰ to +0.5‰) precipitated by mixing oxidizing surface waters with a hydrothermal fluid that contained moderately light Fe ( δ56Fe: -0.5‰) leached from the crystalline basement. Occasional input of CO 2-rich waters resulted in precipitation of isotopically light siderite ( δ56Fe: -1.4 to -0.7‰). The difference between hematite and siderite is compatible with published Fe isotope fractionation factors. The observed

Two types of ore-bearing mafic complexes of the Early Proterozoic East-Scandinavian LIP and their ore potential

NASA Astrophysics Data System (ADS)

Mitrofanov, Felix; Zhirov, Dmitry; Bayanova, Tamara; Korchagin, Alexey; Chaschin, Victor

2015-04-01

Two types of the ore-bearing mafic complexes are allotted in the East-Scandinavian large igneous province (LIP). They differ in geodynamic setting, structure, isotope geochemistry, petrology and mineralogy. The PGE-bearing mafic-ultramafic layered intrusions are associated with the first complex. They have been formed at an initial (pre-rift) stage of LIP. Features of origin of this complex are: 1) large-scale, protracted, and multiple episodes of deep mantle plume or asthenosphere upwelling; 2) the vast non-subduction-type basaltic magma in an intraplate continental setting; 3) low-sulfide Pt-Pd (with Ni, Cu, Au, Co and Rh) mineralization in different geological setting (reef- and contact type etc.); 4) anomalously high concentrations of PGEs in the bulk sulfides, inferred platinum distribution coefficient between silicate and sulfide melts of >100000. Deep mantle magma source is enriched in ore components (fertile source) and lithophile elements. It is reflected in the isotope indicators such as ɛNd(T) from -1 to -3, ISr(87Sr/86Sr) from 0.702 to 0.704, 3Не/4Не = (10 ^-5 ÷ 10 ^-6). Magma and ore sources differ from those of Mid-Ocean Ridge basalts (MORB), subduction-related magma but are similar to EM-I. Ore-bearing mafic complexes formed during a long period of time and by different episodes (2490±10 Ma; 2470±10 Ma; 2450±10 Ma; 2400±10 Ma), and by mixing between the boninitic an anorthositic magmas. It is known about 10 deposits and occurrences in Kola region with total reserves and resources about 2000 tons in palladium equivalent (with an average content ≥2-3 ppm). Intrusions with the rich sulfide Ni-Cu ore (with Co and poor PGE) are associated with the second mafic complex. Ore-controlling mafic-ultramafic intrusions are formed at a final stage of the intracontinental rifting of the Transitional period (2200-1980 Ma). Initial magma is depleted and similar to the MORB in terms of rare earths distribution. Enriched ferropicritic Fe-Ti derivatives of

A precise 232Th-208Pb chronology of fine-grained monazite: Age of the Bayan Obo REE-Fe-Nb ore deposit, China

USGS Publications Warehouse

Wang, Jingyuan; Tatsumoto, M.; Li, X.; Premo, W.R.; Chao, E.C.T.

1994-01-01

We have obtained precise Th-Pb internal isochron ages on monazite and bastnaesite for the world's largest known rare earth elements (REE)-Fe-Nb ore deposit, the Bayan Obo of Inner Mongolia, China. The monazite samples, collected from the carbonate-hosted ore zone, contain extremely small amounts of uranium (less than 10 ppm) but up to 0.7% ThO2. Previous estimates of the age of mineralization ranged from 1.8 to 0.255 Ga. Magnetic fractions of monazite and bastnaesite samples (<60-??m size) showed large ranges in 232Th 204Pb values (900-400,000) and provided precise Th-Pb internal isochron ages for paragenetic monazite mineralization ranging from 555 to 398 Ma within a few percent error (0.8% for two samples). These results are the first indication that REE mineralization within the giant Bayan Obo ore deposit occurred over a long period of time. The initial lead isotopic compositions (low 206Pb 204Pb and high 208Pb 204Pb) and large negative ??{lunate}Nd values for Bayan Obo ore minerals indicate that the main source(s) for the ores was the lower crust which was depleted in uranium, but enriched in thorium and light rare earth elements for a long period of time. Zircon from a quartz monzonite, located 50 km south of the ore complex and thought to be related to Caledonian subduction, gave an age of 451 Ma, within the range of monazite ages. Textural relations together with the mineral ages favor an epigenetic rather than a syngenetic origin for the orebodies. REE mineralization started around 555 Ma (disseminated monazite in the West, the Main, and south of the East Orebody), but the main mineralization (banded ores) was related to the Caledonian subduction event ca. 474-400 Ma. ?? 1994.

Method and apparatus for drilling horizontal holes in geological structures from a vertical bore

DOEpatents

Summers, David A.; Barker, Clark R.; Keith, H. Dean

1982-01-01

This invention is directed to a method and apparatus for drilling horizontal holes in geological strata from a vertical position. The geological structures intended to be penetrated in this fashion are coal seams, as for in situ gasification or methane drainage, or in oil-bearing strata for increasing the flow rate from a pre-existing well. Other possible uses for this device might be for use in the leaching of uranium ore from underground deposits or for introducing horizontal channels for water and steam injections.

Geological modelling of mineral deposits for prediction in mining

NASA Astrophysics Data System (ADS)

Sides, E. J.

Accurate prediction of the shape, location, size and properties of the solid rock materials to be extracted during mining is essential for reliable technical and financial planning. This is achieved through geological modelling of the three-dimensional (3D) shape and properties of the materials present in mineral deposits, and the presentation of results in a form which is accessible to mine planning engineers. In recent years the application of interactive graphics software, offering 3D database handling, modelling and visualisation, has greatly enhanced the options available for predicting the subsurface limits and characteristics of mineral deposits. A review of conventional 3D geological interpretation methods, and the model struc- tures and modelling methods used in reserve estimation and mine planning software packages, illustrates the importance of such approaches in the modern mining industry. Despite the widespread introduction and acceptance of computer hardware and software in mining applications, in recent years, there has been little fundamental change in the way in which geology is used in orebody modelling for predictive purposes. Selected areas of current research, aimed at tackling issues such as the use of orientation data, quantification of morphological differences, incorporation of geological age relationships, multi-resolution models and the application of virtual reality hardware and software, are discussed.

Geology and deposits of the lunar Nectaris basin

NASA Technical Reports Server (NTRS)

Spudis, P. D.; Hawke, B. R.; Lucey, P. G.

1989-01-01

The geology and composition of Nectaris basin deposits have been investigated in order to provide information on the lunar basin-forming process and the regional geologic setting of the Apollo 16 landing site. Several outcrops of nearly pure anorthosite were noted in locations such as the walls of Kant crater, an inner ring of the basin, and the crater Bohnenberger F. The results suggest that the impact can be modeled as a proportional-growth crater, and that the Nectaris excavation cavity was about 470 km in diameter and as deep as 55 km.

Geology and deposits of the lunar Nectaris basin

NASA Astrophysics Data System (ADS)

Spudis, P. D.; Hawke, B. R.; Lucey, P. G.

The geology and composition of Nectaris basin deposits have been investigated in order to provide information on the lunar basin-forming process and the regional geologic setting of the Apollo 16 landing site. Several outcrops of nearly pure anorthosite were noted in locations such as the walls of Kant crater, an inner ring of the basin, and the crater Bohnenberger F. The results suggest that the impact can be modeled as a proportional-growth crater, and that the Nectaris excavation cavity was about 470 km in diameter and as deep as 55 km.

Constraints on the composition of ore fluids and implications for mineralising events at the Cleo gold deposit, Eastern Goldfields Province, Western Australia

USGS Publications Warehouse

Brown, S.M.; Johnson, C.A.; Watling, R.J.; Premo, W.R.

2003-01-01

The Cleo gold deposit, 55 km south of Laverton in the Eastern Goldfields Province of Western Australia, is characterised by banded iron-formation (BIF)-hosted ore zones in the gently dipping Sunrise Shear Zone and high-grade vein-hosted ore in the Western Lodes. There is evidence that gold mineralisation in the Western Lodes (which occurred at ca 2655 Ma) post-dates the majority of displacement along the Sunrise Shear Zone, but it remains uncertain if the ore in both structures formed simultaneously or separately. Overall, the Pb, Nd, Sr, C. O and S isotopic compositions of ore-related minerals from both the Western Lodes and ore zones in the Sunrise Shear Zone are similar. Early low-salinity aqueous-carbonic fluids and late high-salinity fluids with similar characteristics are trapped in inclusions in quartz veins from both the Sunrise Shear Zone and the Western Lodes. The early CO2, CO2-H2O, and H2O- dominant inclusions are interpreted as being related to ore formation, and to have formed from a single low-salinity aqueous-carbonic fluid as a result of intermittent fluid immiscibility. Homogenisation temperatures indicate that these inclusions were trapped at approximately 280??C and at approximately 4 km depth, in the deeper epizonal range. Differences between the ore zones are detected in the trace-element composition of gold samples, with gold from the Sunrise Shear Zone enriched in Ni, Pb, Sn, Te and Zn, and depleted In As, Bi, Cd, Cu and Sb, relative to gold from the Western Lodes. Although there are differences in gold composition between the Sunrise Shear Zone and Western Lodes, and hence the metal content of ore fluids may have varied slightly between the different ore zones, no other systematic fluid or solute differences are detected between the ore zones. Given the fact that the ore fluids in each zone have very similar bulk properties, the considerable differences in gold grade, sulfide mineral abundance, and ore textures between the two ore zones

The first large geological map of Central and Eastern Europe (1815)

NASA Astrophysics Data System (ADS)

Grigelis, Algimantas; Wójcik, Zbigniew; Narębski, Wojciech; Gelumbauskaitė, Leonora Živilė; Kozák, Jan; Czarniecki, Stanisław

2008-01-01

The first large geological map of Central and Eastern Europe was compiled by Stanisław Staszic in the early 19th century. The map is based on the geological survey that Staszic performed in different parts of Poland and adjacent areas. In 1814, Staszic presented his ideas on the geology and mineral sources of Poland and Lithuania. In 1815, he completed the book-length descriptive analysis O ziemorodztwie Karpatów i innych gór i równin Polski przez Stanisława Staszica, which was published in Warsaw and complemented by a large geological map of Central and Eastern Europe. His later studies were compiled in a historico-philosophical treatise titled Ród ludzki (1819-1820). The complete edition of Staszic's works, Dzieła, which also included these publications, appeared over 1816-1820. The geological field survey that he performed over several years, and his study of social-economic problems enabled Staszic to draw in great detail a geological map of the Carpathians, the Central Polish Highlands, Volhynia (modern Ukraine) and the Eastern Alps, as well as the areas of the Polish-Lithuanian Lowlands, the southern coast of the Baltic Sea, Polesye (modern Belarus), Moldova, Transylvania, and Hungary. Staszic was interested in the exploration of mineral deposits, particularly in Poland, which had rock salt, copper and iron ores, and coal. In his monograph and map, he adopted a stratigraphic subdivision based on types of rock contents and organic fossils, which was a slightly modified version of Werner's classification system. The lithological legend sets five classes and 135 different types of rock, and 15 types of ore deposits, using the French names for these. In general, Staszic was an advocate of Werner's paradigm; however, he did not follow exactly the ideas of the German geologist. Staszic's fundamental work recapitulates his views on geological history of Central and Eastern Europe, and brings to an end the Enlightment period in the geology of that part of

Spatial-temporal and genetic relationships between gold and antimony mineralization at gold-sulfide deposits of the Ob-Zaisan folded zone

NASA Astrophysics Data System (ADS)

Kalinin, Yu. A.; Naumov, E. A.; Borisenko, A. S.; Kovalev, K. R.; Antropova, A. I.

2015-05-01

The Ob-Zaisan folded zone is a fragment of a single structure composed of Paleozoic sedimentary and volcanogenic rocks (mainly black shale), which was formed at the margin of the Siberian continent and features a common set of magmatic complexes and mineral systems. However, there are some differences that determine the specific geological and metallogenic features of the Irtysh-Zaisan and Kolyvan-Tomsk fragments of the Ob-Zaisan folded zone. In the gold deposits of the West Kalba and Kolyvan-Tomsk auriferous belt, the main gold-sulfide mineralization is controlled by zones of shearing and dynamic metamorphism in carbonaceous carbonate-terrigenous rocks. This type of mineralization was formed in tectonic blocks in a compressional setting. Antimony mineralization is characterized by brecciated textures and the vein-like morphology of ore bodies, reflecting extensional tectonics. At some deposits (Zherek, Mirazh, Dalny), Sb mineralization is spatially separated from the main gold-sulfide ores and shows cross-cutting relations to the principal ore-controlling structures. In other gold deposits, stibnite is spatially associated with disseminated gold-sulfide ores and forms mineral assemblages with Ni, Co, Au, Pb, and Fe (Alimbet, Zhanan, Legostaevskoe, Semiluzhenskoe, and Kamenskoe deposits). This study reveals no direct correlation between Au and Sb in gold-sulfide ores of these deposits. SEM analysis indicated the absence of free gold in stibnite veins. However, atomic absorption and electron microprobe analysis indicated the presence of "invisible gold" from a few ppm to several tens of ppm in the stibnite. High gold contents in the gold-sulfide ores overprinted by antimony mineralization (Suzdalskoe, Zhanan, and Legostaevskoe deposits) can be explained by the processes of regeneration and redeposition. The results of microstructural observations, isotope geochronology, studies of mineral assemblages and fluid inclusions in the ores from gold deposits of the Ob

Co-Cu-Au deposits in metasedimentary rocks-A preliminary report

USGS Publications Warehouse

Slack, J.F.; Causey, J.D.; Eppinger, R.G.; Gray, J.E.; Johnson, C.A.; Lund, K.I.; Schulz, K.J.

2010-01-01

A compilation of data on global Co-Cu-Au deposits in metasedimentary rocks refines previous descriptive models for their occurrence and provides important information for mineral resource assessments and exploration programs. This compilation forms the basis for a new classification of such deposits, which is speculative at this early stage of research. As defined herein, the Co-Cu-Au deposits contain 0.1 percent or more by weight of Co in ore or mineralized rock, comprising disseminated to semi-massive Co-bearing sulfide minerals with associated Fe- and Cu-bearing sulfides, and local gold, concentrated predominantly within rift-related, siliciclastic metasedimentary rocks of Proterozoic age. Some deposits have appreciable Ag ? Bi ? W ? Ni ? Y ? rare earth elements ? U. Deposit geometry includes stratabound and stratiform layers, lenses, and veins, and (or) discordant veins and breccias. The geometry of most deposits is controlled by stratigraphic layering, folds, axial-plane cleavage, shear zones, breccias, or faults. Ore minerals are mainly cobaltite, skutterudite, glaucodot, and chalcopyrite, with minor gold, arsenopyrite, pyrite, pyrrhotite, bismuthinite, and bismuth; some deposits have appreciable tetrahedrite, uraninite, monazite, allanite, xenotime, apatite, scheelite, or molybdenite. Magnetite can be abundant in breccias, veins, or stratabound lenses within ore or surrounding country rocks. Common gangue minerals include quartz, biotite, muscovite, K-feldspar, albite, chlorite, and scapolite; many deposits contain minor to major amounts of tourmaline. Altered wall rocks generally have abundant biotite or albite. Mesoproterozoic metasedimentary successions constitute the predominant geologic setting. Felsic and (or) mafic plutons are spatially associated with many deposits and at some localities may be contemporaneous with, and involved in, ore formation. Geoenvironmental data for the Blackbird mining district in central Idaho indicate that weathering of

Metallogenic specialization of supercontinent cycles: A case study of silver deposits

NASA Astrophysics Data System (ADS)

Tkachev, A. V.; Rundqvist, D. V.; Vishnevskaya, N. A.

2017-07-01

The distribution of integrated resources of large and superlarge mineral deposits (LSLDs) of silver, where the main part of industrially recoverable silver reserves is concentrated, is compared with the existing model of supercontinent cyclicity over the geological history of the Earth. It is found that each supercontinent cycle (Kenoran, Columbian, Rodinian, Pangean, and Amasian) is particularly expressed in the silver metallogeny. The significant intercycle variations in the numbers of LSLDs, diversity of types of these deposits, accumulated resources, mean tenors of silver in ores, and some other numerically expressible characteristics are revealed. These variations correlate with a number of geohistorical changes in the conditions under which endogenous and exogenous geological processes run.

Geologic map of the western Haji-Gak iron deposit, Bamyan Province, Afghanistan, modified from the 1965 original map compilation of V.V. Reshetniak and I.K. Kusov

USGS Publications Warehouse

Renaud, Karine M.; Tucker, Robert D.; Peters, Stephen G.; Stettner, Will R.; Masonic, Linda M.; Moran, Thomas W.

2011-01-01

This map is a modified version of Geologic-prospecting plan of western area of Hajigak iron-ore deposit, scale 1:2,000, which was compiled by V.V. Reshetniak and I.K. Kusov in 1965. (Refer to the References Cited section in the Map PDF for complete citations of the original map and related reports.) USGS scientists, in cooperation with the Afghan Geological Survey and the Task Force for Business and Stability Operations of the U.S. Department of Defense, studied the original documents and also visited the field area in November 2009. This modified map illustrates the geological structure of the western Haji-Gak iron deposit and includes cross sections of the same area. The map reproduces the topology (contacts, faults, and so forth) of the original Soviet map and includes modifications based on our examination of that document. We constructed the cross sections from data derived from the original map. Elevations on the cross sections are derived from the original Soviet topography and may not match the newer topography used on the current map. We have attempted to translate the original Russian terminology and rock classification into modern English geologic usage as literally as possible without changing any genetic or process-oriented implications in the original descriptions. We also use the age designations from the original map. The unit colors on the map and cross sections differ from the colors shown on the original version. The units are colored according to the color and pattern scheme of the Commission for the Geological Map of the World (CGMW) (http://www.ccgm.org).

Geology of the Shinarump No. 1 uranium mine, Seven Mile Canyon area, Grand County, Utah

USGS Publications Warehouse

Finch, Warren Irvin

1954-01-01

The geology of the Shinarump No. 1 uranium mine, located about 12 miles northwest of Moab, Utah, in the Seven Mile Canyon area, Grand County, Utah, was studied to determine the habits, ore controls, and possible origin of the deposit. Rocks of Permian, Triassic, and Jurassic age crop out in the area mapped, and uranium deposits are found in three zones in the lower 25 feet of the Chinle formation of Late Triassic age. The Shinarump No. 1 mine, which is in the lowermost zone, is located on the west flank of the Moab anticline near the Moab fault. The Shinarump No. 1 uranium deposit consists of discontinuous lenticular layers of mineralized rock, irregular in outline, that, in general, follow the bedding. Ore minerals, mainly uraninite, impregnate the rock. High-grade ore seams of uraninite and chalcocite occur along bedding planes. Uraninite formed later than, or simultaneous with, most sulfides, and the chalcocite may be of two ages, with some being later than uraninite. Uraninite and chalcocite are concentrated in the more poorly sorted parts of siltstones. In the Seven Mile Canyon area guides to ore inferred from the study of the Shinarump No. 1 deposit are the presence of bleached siltstone, carbonaceous matter, and copper sulfides. Results of spectrographic analysis indicate that the mineralizing solutions contained important amounts of barium, vanadium, uranium, and copper, as well as lesser amounts of strontium, chromium, boron, yttrium, lead, and zinc. The origin of the Shinarump No. 1 deposit is thought to be hydrothermal.

Chapter C: Hydrothermal Enrichment of Gallium in Zones of Advanced Argillic Alteration-Examples from the Paradise Peak and McDermitt Ore Deposits, Nevada

USGS Publications Warehouse

Rytuba, James J.; John, David A.; Foster, Andrea; Ludington, Steven D.; Kotlyar, Boris

2003-01-01

Gallium is produced as a byproduct from bauxite and zinc sulfide ores and rarely from primary Ga ores. High Ga contents (>60 ppm) can occur in zones of advanced argillic alteration consisting of alunite+kaolinite+quartz associated with quartz-alunite (high sulfidation Au-Ag) deposits. In a magmatic-hydrothermal environment, the zones of advanced argillic alteration associated with quartz-alunite (high sulfidation) Au-Ag deposits have the highest Ga contents (max 120 ppm). In these Au deposits, Ga is enriched in the zone of alunite+kaolinite alteration and depleted in the zone of quartz-rich alteration within acid-leached rocks. Peripheral zones of argillic alteration have Ga contents and Al/Ga ratios similar to those in unaltered volcanic rocks. The zones of advanced argillic alteration that formed in a steam-heated environment in association with hot-spring-type Hg-Au deposits are not Ga enriched, and residual silicified zones have very low Ga contents. The McDermitt Hg and Paradise Peak Au-Hg deposits, Nev., have zones of advanced argillic alteration that are Ga enriched. At the Paradise Peak Au-Hg deposits, Ga is enriched in the zone of alunite+jarosite alteration that formed in a magmatic-hydrothermal environment. Ga is depleted in the zone of opal+alunite alteration formed in a steam-heated environment, in residual silicified zones formed in a magmatic-hydrothermal environment, and in zones of supergene jarosite alteration. At the McDermitt Hg deposit, Ga is enriched in the zone of alunite+kaolinite alteration below the zone of adularia-quartz alteration that coincides with the Hg ore body. The spatial relation of Ga enrichment to alunite-kaolinite alteration suggests that formation in a magmatic-hydrothermal environment. X-ray-absorption spectra of Ga-enriched samples from the McDermitt Hg deposit are similar to that of gallium sulfate and support the association of Ga enrichment with alunite alteration.

Stratiform chromite deposit model

USGS Publications Warehouse

Schulte, Ruth F.; Taylor, Ryan D.; Piatak, Nadine M.; Seal, Robert R.

2010-01-01

Stratiform chromite deposits are of great economic importance, yet their origin and evolution remain highly debated. Layered igneous intrusions such as the Bushveld, Great Dyke, Kemi, and Stillwater Complexes, provide opportunities for studying magmatic differentiation processes and assimilation within the crust, as well as related ore-deposit formation. Chromite-rich seams within layered intrusions host the majority of the world's chromium reserves and may contain significant platinum-group-element (PGE) mineralization. This model of stratiform chromite deposits is part of an effort by the U.S. Geological Survey's Mineral Resources Program to update existing models and develop new descriptive mineral deposit models to supplement previously published models for use in mineral-resource and mineral-environmental assessments. The model focuses on features that may be common to all stratiform chromite deposits as a way to gain insight into the processes that gave rise to their emplacement and to the significant economic resources contained in them.

Paleomagnetic Constraints on the age of the Lisheen Zn-Pb Deposit, Ireland: A Pre- Variscan Metamorphosed "MVT" Versus an Epigenetic Variscan Model for Ore Genesis

NASA Astrophysics Data System (ADS)

Pannalal, S. J.; Symons, D. T.; Sangster, D. F.

2009-05-01

Lower Carboniferous carbonate units in the Irish Midlands host major Zn-Pb ore deposits in two units, the Navan Group and the Waulsortian Limestone. The age and, therefore, the genesis of these ore deposits remains controversial because of the lack of absolute geochronological constraints. In addition, the effect of the Early Permian Variscan thermal episode, observed by elevated conodont color alteration indices in all Carboniferous strata in Ireland, on the Zn-Pb ore deposits is not clearly understood. This paleomagnetic study was undertaken to date and, thereby, constrain the genesis of the Waulsortian Limestone-hosted Lisheen Zn- Pb ore deposit. Specimens (432) from 12 sites in ore mineralization and 10 sites in host rocks at Lisheen were subjected to alternating-field and thermal step demagnetization protocols. Analysis of these specimens isolated a well-defined stable shallow and southerly-up paleomagnetic characteristic remanent magnetization (ChRM) direction. Saturation remanence tests, thermal decay data, and a paleomagnetic tilt test indicate a post-folding ChRM that is carried dominantly by single-domain magnetite. The ChRM directions from 8 host rock and 11 Zn-Pb mineralized sites are indistinguishable at 95% confidence, and give a mean paleopole at 41.6° S, 18.8° W (dp = 1.7°, dm = 3.3° ) with a paleomagnetic age of 277 ± 7 (2 σ) Ma on the apparent polar wander path for Laurentia in European coordinates. This Early Permian magnetization postdates peak-Variscan orogenic heating to ˜ 350° C in the surrounding region, suggesting two basic genetic models for Lisheen's Zn-Pb mineralization i.e. Variscan and metamorphosed pre-Variscan. The Variscan model, our preferred interpretation, suggests that the Zn-Pb mineralizing event occurred at 277 Ma during cooling from the regional Variscan thermal episode. This model, in conjunction with other thermal data, supports an entirely epigenetic origin that invokes a topographically-driven fluid flow, either

The indirect electrochemical refining of lunar ores

NASA Technical Reports Server (NTRS)

Semkow, Krystyna W.; Sammells, Anthony F.

1987-01-01

Recent work performed on an electrolytic cell is reported which addresses the implicit limitations in various approaches to refining lunar ores. The cell uses an oxygen vacancy conducting stabilized zirconia solid electrolyte to effect separation between a molten salt catholyte compartment where alkali metals are deposited, and an oxygen-evolving anode of composition La(0.89)Sr(0.1)MnO3. The cell configuration is shown and discussed along with a polarization curve and a steady-state current-voltage curve. In a practical cell, cathodically deposited liquid lithium would be continuously removed from the electrolytic cell and used as a valuable reducing agent for ore refining under lunar conditions. Oxygen would be indirectly electrochemically extracted from lunar ores for breathing purposes.

Re-Os sulfide geochronology of the Red Dog sediment-hosted Zn-Pb-Ag deposit, Brooks Range, Alaska

USGS Publications Warehouse

Morelli, R.M.; Creaser, R.A.; Selby, D.; Kelley, K.D.; Leach, D.L.; King, A.R.

2004-01-01

The Red Dog sediment-hosted deposit in the De Long Mountains of northern Alaska is the largest Zn producer in the world. Main stage mineralization is characterized by massive sulfide ore and crosscutting subvertical veins. Although the vein mineralization is clearly younger than the massive ore, the exact temporal relationship between the two is unclear. Re-Os geochronology of pyrite is used to determine the absolute age of main stage ore at Red Dog. A 10-point isochron on both massive and vein pyrite yields an age of 338.3 ?? 5.8 Ma and is interpreted to represent the age of main stage ore. The Re-Os data indicate that both massive and vein ore types are coeval within the resolution of the technique. Formation of the Red Dog deposit was associated with extension along a passive continental margin, and therefore the Re-Os age of main stage ore constrains the timing of rifting as well as the age of the host sedimentary rocks. Sphalerite from both massive and vein ore yields imprecise ages and shows a high degree of scatter compared to pyrite. We suggest that the Re-Os systematics of sphalerite can be disturbed and that this mineral is not reliable for Re-Os geochronology. ?? 2004 by Economic Geology.

Lead isotope studies of the Guerrero composite terrane, west-central Mexico: implications for ore genesis

NASA Astrophysics Data System (ADS)

Potra, Adriana; Macfarlane, Andrew W.

2014-01-01

New thermal ionization mass spectrometry and multi-collector inductively coupled plasma mass spectrometry Pb isotope analyses of three Cenozoic ores from the La Verde porphyry copper deposit located in the Zihuatanejo-Huetamo subterrane of the Guerrero composite terrane are presented and the metal sources are evaluated. Lead isotope ratios of 3 Cenozoic ores from the El Malacate and La Esmeralda porphyry copper deposits located in the Zihuatanejo-Huetamo subterrane and of 14 ores from the Zimapan and La Negra skarn deposits from the adjoining Sierra Madre terrane are also presented to look for systematic differences in the lead isotope trends and ore metal sources among the proposed exotic tectonostratigraphic terranes of southern Mexico. Comparison among the isotopic signatures of ores from the Sierra Madre terrane and distinct subterranes of the Guerrero terrane supports the idea that there is no direct correlation between the distinct suspect terranes of Mexico and the isotopic signatures of the associated Cenozoic ores. Rather, these Pb isotope patterns are interpreted to reflect increasing crustal contribution to mantle-derived magmas as the arc advanced eastward onto a progressively thicker continental crust. The lead isotope trend observed in Cenozoic ores is not recognized in the ores from Mesozoic volcanogenic massive sulfide and sedimentary exhalative deposits. The Mesozoic ores formed prior to the amalgamation of the Guerrero composite terrane to the continental margin, which took place during the Late Cretaceous, in intraoceanic island arc and intracontinental marginal basin settings, while the Tertiary deposits formed after this event in a continental arc setting. Lead isotope ratios of the Mesozoic and Cenozoic ores appear to reflect these differences in tectonic setting of ore formation. Most Pb isotope values of ores from the La Verde deposit (206Pb/204Pb = 18.674-18.719) are less radiogenic than those of the host igneous rocks, but plot within the

Exploration for uranium deposits in the Atkinson Mesa area, Montrose County, Colorado

USGS Publications Warehouse

Brew, Daniel Allen

1954-01-01

The U.S. Geological Survey explored the Atkinson Mesa area for uranium- and vanadium-bearing deposits from July 2, 1951, to June 18, 1953, with 397 diamond-drill holes that totaled 261,251 feet. Sedimentary rocks of Mesozoic age are exposed in the Atkinson Mesa area. They are: the Brushy Basin member of the Upper Jurassic Morrison formation, the Lower Cretaceous Burro Canyon formation, and the Upper and Lower Cretaceous Dakota sandstone. All of the large uranium-vanadium deposits discovered by Geological Survey drilling are in a series of sandstone lenses in the upper part of the Salt Wash member of the Jurassic Morrison formation. The deposits are mainly tabular and blanket-like, but some elongate pod-shaped masses, locally called "rolls" may be present. The mineralized material consists of sandstone impregnated with a uranium mineral which is probably coffinite, spme carnotite, and vanadium minerals, thought to be mainly corvusite and montroseite. In addition,, some mudstone and carbonaceous material is similarly impregnated. Near masses of mineralized material the sandstone is light gray or light brown, is generally over 40 feet thick, and usually contains some carbonaceous material and abundant disseminated pyrite or limonite stain. Similarly, the mudstone in contact with the ore-bearing sandstone near bodies of mineralized rock is commonly blue gray, as compared to its dominant red color away from ore deposits. Presence and degree of these features are useful guides in exploring for new deposits.

Geologic Mapping of Ejecta Deposits in Oppia Quadrangle, Asteroid (4) Vesta

NASA Technical Reports Server (NTRS)

Garry, W. Brent; Williams, David A.; Yingst, R. Aileen; Mest, Scott C.; Buczkowski, Debra L.; Tosi, Federico; Schafer, Michael; LeCorre, Lucille; Reddy, Vishnu; Jaumann, Ralf;

The role of the U.S. Geological Survey in the lithium industry

USGS Publications Warehouse

Vine, J.D.

1978-01-01

The U.S. Geological Survey has responsibility in the U.S. Department of the Interior to assess the nation's energy and mineral resources. The evaluation of reserves and resources of a commodity such as lithium should be a continuing process in the light of advancing technology and ever-growing knowledge of its geologic occurrence and geochemical behavior. Although reserves of lithium vary with market demand because of the investment required to find, develop, and appraise an ore body, total resources are a function of the geologic occurrence and geochemical behavior of lithium. By studying known deposits and publishing data on their origin and occurrence, the U.S. Geological Survey can aid in the discovery of new deposits and improve the resource base. Resource data are used both by the government and the private sector. Government funding for research on energy-related technologies such as electric vehicle batteries and fusion power requires assurance that there will be enough lithium available in time for commercialization. Questions of availability for all mineral commodities must be answered by the U.S. Geological Survey so that intelligent decisions can be made. ?? 1978.

Origin of the Lengshuigou porphyry-skarn Cu deposit in the Zha-Shan district, South Qinling, central China, and implications for differences between porphyry Cu and Mo deposits

NASA Astrophysics Data System (ADS)

Xie, Guiqing; Mao, Jingwen; Wang, Ruiting; Meng, Deming; Sun, Jia; Dai, Junzhi; Ren, Tao; Li, Jianbi; Zhao, Haijie

2017-04-01

Porphyry Cu and Mo deposits are two economically important types of metal deposits worldwide, but factors controlling their difference remain enigmatic. Compared with the well-studied large porphyry Mo province in the south margin of the North China Block (S-NCB), the origin of newly discovered porphyry Cu deposits in the South Qinling (SQB) is poorly constrained. Integrated zircon LA-ICPMS U-Pb and molybdenite Re-Os ages and geological evidence indicate three stages of magmatism at Lengshuigou: (1) late Neoproterozoic (718 to 704 Ma) quartz diorite + albitite + granite association during the pre-ore stage, (2) 146 to 145 Ma granodiorite porphyry during the syn-ore stage, and (3) 145 Ma granite porphyry during the post-ore stage. Elemental and Sr-Nd isotopic evidence provide important constraints on their magma source. Pre-ore Neoproterozoic quartz diorite + albitite + granite was derived by re-melting of a mixture of crustal and juvenile mantle materials, and stronger fractional crystallization was involved in these ore-hosting intrusions than in contemporary granitoids hosted in the Douling Group. Syn-ore granodiorite porphyry was derived from mantle-derived magma with contributions from different proportions of crustal components. Post-ore granite porphyry was derived mainly from a crustal source. Nearly contemporaneous porphyry Cu and Mo systems were identified in Qinling Province, including the 147-139 Ma porphyry Mo systems in the S-NCB and 150-146 Ma porphyry Cu systems in the SQB. Granitic stocks related to porphyry Cu systems in the SQB are characterized by moderate SiO2 contents (58.01-69.07 %) and less radiogenic Nd-Hf isotopes (ɛNd(t) = -3.8 to -6.3, ɛHf(t) = -4.5 to +1.6), whereas the granitic stocks related to porphyry Mo deposits in the S-NCB have high SiO2 concentrations (64.00-76.00 %) and more radiogenic Nd-Hf isotopes (ɛNd(t) = -18.0 to -11.6, ɛHf(t) = -26.3 to -13.5). In addition, molybdenite from the Chigou and Lengshuigou porphyry Cu

Application of LANDSAT satellite imagery for iron ore prospecting in the Western Desert of Egypt

NASA Technical Reports Server (NTRS)

Elshazly, E. M.; Abdelhady, M. A.; Elghawaby, M. A.; Khawasik, S. M.

1977-01-01

Prospecting for iron ore occurrences was conducted by the Remote Sensing Center in Bahariya Oasis-El Faiyum area covering some 100,000 km squared in the Western Desert of Egypt. LANDSAT-1 satellite images were utilized as the main tool in the regional prospecting of the iron ores. The delineation of the geological units and geological structure through the interpretation of the images corroborated by field observations and structural analysis led to the discovery of new iron ore occurrences in the area of investigation.

Positive feedback between strain localization and fluid flow at the ductile-brittle transition leading to Pb-Zn-Fe-Cu-Ag ore deposits in Lavrion (Greece)

NASA Astrophysics Data System (ADS)

Scheffer, Christophe; Tarantola, Alexandre; Vanderhaeghe, Olivier

2016-04-01

At the crustal scale, the ductile-brittle transition (DBT) might correspond to a physical barrier that separates a deep reservoir of metamorphic and magmatic fluids from a shallow reservoir of surficial fluids. Rock rheology, and thus the location of the DBT, is mainly governed by lithology, temperature and the presence/absence of fluids. Accordingly, the position of the DBT potentially evolves during orogenic evolution owing to thermal evolution and fluid circulation. In turn rocks are transferred across it during burial and exhumation. These processes induce connections between fluid reservoirs which might play a role on ore deposition. In this contribution, we discuss the impact of lithological heterogeneities on deformation, fluid flow and ore deposition based on the example of the Lavrion low-angle top-to-the-SSW detachment accommodating gravitational collapse of the Hellenides orogenic belt in Greece. The Lavrion peninsula, localized along the western boundary of the Attic-Cycladic Metamorphic Core Complex, is characterized by Pb-Zn-Fe-Cu-Ag ore mineralization mainly concentrated along a lithological contact (marble/schists) below and within a detachment shear zone. The mylonitic marble below the detachment shear zone is composed of white layers of pure marble alternating with blue layers containing impurities (SiO2, Al2O3, organic matter…). Development of the mylonitic fabric in competent impure blue marble is associated with its preferred dolomitization related to focused fluid infiltration. This mylonitic marble is cross-cut by several cataclastic horizons preferentially developed within the more competent impure blue marble and newly-crystallized dolomitic horizon. These cataclasites are invaded by fluorite and calcite gangue minerals showing locally Mn, Pb, Zn, Fe oxides and/or hydroxides, sphalerite, Ag-galena, Ag-sulfur and native Ag. Oxygen and carbon stable isotopes performed on marble sections point out decarbonation with magmatic contribution and

Origin of stratiform sediment-hosted manganese carbonate ore deposits: Examples from Molango, Mexico, and TaoJiang, China

USGS Publications Warehouse

Okita, P.M.; Shanks, Wayne C.

1992-01-01

Carbonate and sulfide minerals from the Molango, Mexico, and TaoJiang, China, Mn deposits display similar and distinctive ??34S and ??13C patterns in intervals of manganese carbonate mineralization. ??13C-values for Mn-bearing carbonate range from -17.8 to +0.5??? (PDB), with the most negative values occurring in high-grade ore zones that are composed predominantly of rhodochrosite. In contrast, calcite from below, within and above Mn-carbonate zones at Molango has ??13C???0??? (PDB). Markedly negative ??13C data indicate that a large proportion of the carbon in Mn-carbonates was derived from organic matter oxidation. Diagenetic reactions using MnO2 and SO2-4 to oxidize sedimentary organic matter were the principle causes of such 12C enrichment. Pyrite content and sulfide ?? 34S-values also show distinctive variations. In unmineralized rocks, very negative ??34S-values (avg. < -21??? CDT) and abundant pyrite content suggest that pyrite formed from diagenetic, bacteriogenic sulfate reduction. In contrast, Mn-bearing horizons typically contain only trace amounts of pyrite (e.g., <0.5 wt% S with ??34S-values 34S-enriched, in some cases to nearly the value for contemporaneous seawater. 34S-enriched pyrite from the Mn-carbonate intervals indicates sulfide precipitation in an environment that underwent extensive SO2-4 reduction, and was largely a closed system with regard to exchange of sulfate and dissolved sulfide with normal seawater. The occasional occurrence of 34S-depleted pyrite within Mn-carbonate zones dominated by 34S-enriched pyrite is evidence that closed-system conditions were intermittent and limited to local pore waters and did not involve entire sedimentary basins. Mn-carbonate precipitation may have occluded porosity in the surficial sediments, thus establishing an effective barrier to SO2-4 exchange with overlying seawater. Similar isotopic and mineralogic characteristics from both the Molango and TaoJiang deposits, widely separated in geologic time and

Ore genesis dating: implication of Sm-Nd method using sulfide minerals for mafic-ultramafic layered intrusions of Fennoscandian Shield

NASA Astrophysics Data System (ADS)

Serov, Pavel; Bayanova, Tamara; Steshenko, Ekaterina; Ekimova, Nadezhda

2015-04-01

and brecciform ores of the following objects - Pilguyarvi Cu-Ni deposits, Pechenga (1965±87 Ma); impregnated (2433±83 Ma) and redeposited (1903±24 Ma) ores of Ahmavaara intrusion (Finland); Kolvitsa massif metagabbro (1990±92 Ma, which reflect the age of Sm-Nd system closure in sulfide minerals); olivine orthopyroxenites of Sopcha 'Ore bed' (2442±59 Ma); ore gabbronorites of Penikat PGE-bearing layered intrusion (2426±38 Ma (Ekimova et.al., 2011); Pt-Pd gabbro-pegmatite ores (2476± 41 Ma, which agrees well with the U-Pb zircon age - 2470±9 Ma (Bayanova, 2004) and gabbronorites (2483±86 Ma) of PGE Kievey deposit and Fedorova Tundra metagabbroids (2494±54 Ma); Monchetundra gabbronorites - 2489±49 Ma. All investigations are devoted to memory of academician RAS, professor F. Mitrofanov (Russia), he was a leader of scientific school for geology, geochemistry and metallogenesis of ore deposits. The studies were supported by the RFBR 13-05-00493, OFI-M 13-05-12055, Department of Earth Sciences RAS (programs 2 and 4), IGCP-599.

Iron-ore resources of the United States including Alaska and Puerto Rico, 1955

USGS Publications Warehouse

Carr, Martha S.; Dutton, Carl E.

1959-01-01

The importance of iron ore, the basic raw material of steel, as a fundamental mineral, resource is shown by the fact that about 100 million long tons of steel is used annually in the economy of the United States, as compared with a combined total of about 5 million long tons of copper, lead, zinc, and aluminum. Satisfying this annual demand for steel requires about 110 million tons of iron ore and 70 million tons of scrap iron and steel. The average annual consumption of iron ore in the United States from 1951 to 1955, inclusive, was about 110 million long tons, which is about twice the annual average from 1900 to 1930. Production of iron ore in the United States in this 5-year period averaged approximately 100 million long tons annually, divided by regions as follows (in percent): Lake Superior, 84.1; southeastern, 6.7; western, 6.7; northeastern, 1.4; and central and gulf, 1.1. Mining of iron ore began in the American Colonies about 1619, and for 225 years it was limited to eastern United States where fuel and markets were readily available. Production of iron ore from the Lake Superior region began in 1846; the region became the leading domestic source by 1890, and the Mesabi range in Minnesota has been the world's most productive area since 1896. Proximity of raw materials, water transportation, and markets has resulted in centralization of the country's iron and steel industry in the lower Great Lakes area. Increased imports of iron ore being delivered to eastern United States as well as demands for steel in nearby markets have given impetus to expansion in the steel-making capacity in this area. The four chief iron-ore minerals - hematite, liminite, magnetite, and siderite - are widely distributed but only locally form deposits of sufficient tonnage and grade to be commercially valuable at the present time. The iron content of these minerals, of which hematite is the most important, ranges from 48 percent in siderite to 72 percent in magnetite, but as these

Barite-polymetallic mineralization of Zmeinogorsk ore district and some genetic aspects of its formation

NASA Astrophysics Data System (ADS)

Bestemianova, K. V.; Grinev, O. M.

2017-12-01

Zmeinogorsky ore district is located in the northwest part of Ore Altai megatrough, which has long-lasting history of its development and complicated geological structure. Within the ore district, which is the northwest part of the devonian Zmeinogorsk-Bystrushinsky trough, ore mineralization is associated with the system of northwest border faults and cross branch faults. There were four main stages and five phases of minerogenesis. The first stage is the stage of oregenesis beginning and quartz-chlorite-sericite wall-rock alteration rocks formation. Ore deposition and intense tectonics took place during the second stage. The third stage is the most longstanding and productive ore formation stage. There are five distinct minerogenesis phases within this stage. The fourth stage expressed in erosion development and supergene alteration of already formed ore bodies with oxidation zone formation. Main ore minerals are pyrite, chalcopyrite, sphalerite and galena. Minor minerals are tetrahedrite, bornite, tennantite and chalcocite. Precious metals minerals are acanthite, gold, electrum, gold and silver amalgams. Barren minerals are barite, quartz, calcite, gypsum. According to obtained data average isotopic composition of third stage sulphides is: pyrite -0,2‰, chalcopyrite 0‰, galena +0,5‰, sphalerite -1,2‰ for the first complex; chalcopyrite -1,9‰, galena -3,4‰, sphalerite -2,3‰, tetrahedrite -3,7‰ for the second complex; tennantite -12,8‰, bornite -8,9‰ for the third complex. Sulfur isotopic compoisiton variations indicate source inhomogeneity. Thus, there was dominant source change from mantle one in the beginning to crustal one in the end. Main oregenesis stages took place in the range of temperatures between 170 and 210°С and in the mineral-forming solutions salinity range between 3 and 10 wt % NaCl equiv.

Geology and uranium deposits of the Cochetopa and Marshall Pass districts, Saguache and Gunnison counties, Colorado

USGS Publications Warehouse

Olson, Jerry C.

1988-01-01

The Cochetopa and Marshall Pass uranium districts are in Saguache and Gunnison Counties, south-central Colorado. Geologic mapping of both districts has shown that their structural history and geologic relationships have a bearing on the distribution and origin of their uranium deposits. In both districts, the principal uranium deposits are situated at the intersection of major faults with Tertiary erosion surfaces. These surfaces were buried by early Tertiary siliceous tuffs-- a likely source of the uranium. That uranium deposits are related to such unconformities in various parts of the world has been suggested by many other authors. The purpose of this study is to understand the geology of the two districts and to define a genetic model for uranium deposits that may be useful in the discovery and evaluation of uranium deposits in these and other similar geologic settings. The Cochetopa and Marshall Pass uranium districts produced nearly 1,200 metric tons of uranium oxide from 1956 to 1963. Several workings at the Los Ochos mine in the Cochetopa district, and the Pitch mine in the Marshall Pass district, accounted for about 97 percent of this production, but numerous other occurrences of uranium are known in the two districts. As a result of exploration of the Pitch deposit in the 1970's, a large open-pit mining operation began in 1978. Proterozoic rocks in both districts comprise metavolcanic, metasedimentary, and igneous units. Granitic rocks, predominantly quartz monzonitic in composition, occupy large areas. In the northwestern part of the Cochetopa district, metavolcanic and related metasedimentary rocks are of low grade (lower amphibolite facies). In the Marshall Pass district, layered metamorphic rocks are predominantly metasedimentary and are of higher (sillimanite subfacies) grade than the Cochetopa rocks. Paleozoic sedimentary rocks in the Marshall Pass district range from Late Cambrian to Pennsylvanian in age and are 700 m thick. The Paleozoic rocks

Understanding the residence of Co in ore minerals - towards the development of novel Co extraction strategies for laterite deposits

NASA Astrophysics Data System (ADS)

Dybowska, Agnieszka; Norman, Rachel; Schofield, Paul; Herrington, Richard

2017-04-01

Cobalt has unique properties highly valued for many applications essential to the green economy. It has been classified as a critical raw material due to the particularly high risk of supply shortage and its importance for the value chain. Despite low crustal abundance (25ppm), Co is concentrated by various geological processes to concentrations suitable for mining, however the majority of Co is recovered as a by-product of Cu and Ni processing in three principal geological settings: hydrothermal, magmatic and lateritic. Cobalt-rich laterites, which provide 20% of the world's Co, are mainly processed using energy-inefficient pyrometallurgical techniques or high-pressure acid leaching technologies often optimised for extraction of other elements, which can leave between 50 and 80% of the Co unrecovered. In order to develop more efficient Co extraction strategies, understanding the residence of Co in ore minerals is essential. To this end, we are undertaking a detailed mineralogical, chemical and atomistic-scale characterization of Co in samples from a range of laterite deposits. Bulk samples representative of the average ore material were sourced from a variety of undeveloped laterite deposits: Shevchenko (Kazakhstan), Acoje (Philippines), Nkamouna (Cameroon) and Piauí (Brazil). Bulk chemical and mineralogical characterisation was undertaken with ICP-OES/MS and XRD, followed by spatially resolved chemical and mineralogical imaging at the micron scale using µXRD, EPMA, SEM and synchrotron-based µXRF. The chemical state and local environment of Co were determined using X ray spectroscopy (μXANES and μEXAFS). The total concentrations of Co ranged from 630 to 2780 mg/kg. The ore mineral assemblage in the various samples includes goethite, maghemite, hematite, quartz, talc, serpentines, chlorites, smectites, kaolinite and chromites. Manganese oxide minerals are present but, due to their poor crystallinity and low concentration, are not routinely detectable with bulk

Economic Geology (Metals)

ERIC Educational Resources Information Center

Gair, Jacob E.

1972-01-01

Reviews metalliferous ore-deposit research reported in 1971. Research was dominated by isotopic studies, and worldwide metals exploration was marked by announcements of important new discoveries of base metals, iron ore, nickel, titanium, and uranium. (Author/PR)

Geologic Criteria for the Assessment of Sedimentary Exhalative (Sedex) Zn-Pb-Ag Deposits

USGS Publications Warehouse

Emsbo, Poul

2009-01-01

Sedex deposits account for more than 50 percent of the world's zinc and lead reserves and furnish more than 25 percent of the world's production of these two metals. This report draws on previous syntheses as well as on topical studies of deposits in sedex basins to determine the characteristics and processes that produced sedex deposits. This analysis also uses studies of the tectonic, sedimentary, and fluid evolution of modern and ancient sedimentary basins and mass balance constraints to identify the hydrothermal processes that are required to produce sedex deposits. This report demonstrates how a genetic model can be translated into geologic criteria that can be used in the U.S. Geological Survey National Assessments for sedex zinc-lead-silver deposits to define permissive tracts, assess the relative prospectivity of permissive tracts, and map favorability within permissive tracts.

New observations on the Ni-Co ores of the southern Arburese Variscan district (SW Sardinia, Italy)

NASA Astrophysics Data System (ADS)

Naitza, Stefano; Secchi, Francesco; Oggiano, Giacomo; Cuccuru, Stefano

2015-04-01

Among the European Variscan regions, the Arburese district, located in the Paleozoic basement of SW Sardinia (Italy) is remarkable for its metallogenic complexity, and offers good opportunities to investigate time/space and genetic links between post-collisional Variscan intrusive magmatism and mineral deposits. The district hosts a large variety of mineral deposits and occurrences, which include the Pb-Zn (Cu, Ag) mesothermal veins of the Montevecchio Lode System, one of the largest and richest Variscan hydrothermal ore deposit of Europe, now exhausted. Ore deposits are genetically related to the emplacement of the Late Variscan (304±1 Ma) Arbus Pluton, a granitoid composite intrusion ranging from monzogabbroic to granodioritic and to peraluminous leucogranitic rock-types. After more than a century of geological studies in the area, several metallogenic issues are still unresolved; among them, the occurrence in the southern sectors of little known polymetallic Ni-Co-(Pb-Zn-Cu-Ag-Bi) veins, a kind of mineralization quite unusual for the Sardinian basement. These hydrothermal deposits are hosted by very low-grade metamorphic rocks at short distance from the intrusion, where contact effect generate also hornfels. Spatial, structural and textural characters of the hydrothermal system are coherent and in apparent continuity with those of the Montevecchio Lode System. Ni-Co ores are hosted by a system of parallel, 1-2 m thick high-angle veins that discontinuously follow the southwestern and southern contacts of the Arbus Pluton for about 7 km. They constantly dip SSW, sideways with respect to the pluton contact, and show a prevalence of fracture infilling (banded and brecciated) textures, with alternating quartz and siderite bands, cockades and frequent inclusions of wallrock fragments. Wallrocks are usually silicified, bleached and/or sericitized. Systematic studies of ore textures and parageneses from different veins along the system have been performed by standard

Geochronology, petrogenesis and tectonic settings of pre- and syn-ore granites from the W-Mo deposits (East Kounrad, Zhanet and Akshatau), Central Kazakhstan

NASA Astrophysics Data System (ADS)

Li, GuangMing; Cao, MingJian; Qin, KeZhang; Evans, Noreen J.; Hollings, Pete; Seitmuratova, Eleonora Yusupovha

2016-05-01

There is significant debate regarding the mineralization ages of the East Kounrad, Zhanet and Akshatau W-Mo deposits of Central Kazakhstan, and the petrogenesis and tectono-magmatic evolution of the granites associated with these deposits. To address these issues, we present molybdenite Re-Os dating, zircon U-Pb dating, whole rock geochemistry as well as Sr-Nd-Pb and zircon O-Hf isotopic analyses on the pre-mineralization and ore-forming granites. U-Pb dating of zircons from pre-mineralization granitic rocks yield Late Carboniferous ages of 320-309 Ma, whereas ore-forming granites have Early Permian ages of 298-285 Ma. Molybdenite Re-Os isotopic data indicate a mineralization age of 296 Ma at East Kounrad, 294 Ma at Akshatau and 285 Ma at Zhanet. The pre-ore and ore-forming granites are high-K calc-alkaline, metaluminous to slightly peraluminous I-type granites. The pre-mineralization granites are relatively unfractionated, whereas the ore-forming granites are highly fractionated. The fractionating mineral phases are probably K-feldspar, apatite, Ti-bearing phases and minor plagioclase. The pre-mineralization and ore-forming rocks are characterized by similar Sr-Nd-Pb-Hf-O isotopic compositions ((87Sr/86Sr)i = 0.70308-0.70501, εNd (t) = - 0.5 to + 2.8, 207Pb/204Pb = 15.60-15.82, zircon εHf (t) = + 1.2 to + 15.6 and δ18O = + 4.6 to + 10.3‰), whole rock TDMC (Nd) (840-1120 Ma) and zircon TDMC (Hf) (320-1240 Ma). The isotopic characteristics are consistent with a hybrid magma source caused by 10-30% assimilation of ancient crust by juvenile lower crust. The geochronology and geochemistry of these granites show that the Late Carboniferous pre-mineralization granitic rocks formed during subduction, whereas the Early Permian ore-forming, highly fractionated granite probably underwent significant fractionation with a restite assemblage of K-feldspar, apatite, Ti-bearing phases and minor plagioclase and developed during collision between the Yili and Kazakhstan

Geology and mineral deposits of Churchill County, Nevada

USGS Publications Warehouse

Willden, Ronald; Speed, Robert C.

1974-01-01

Churchill County, in west-central Nevada, is an area of varied topography and geology that has had a rather small total mineral production. The western part of the county is dominated by the broad low valley of the Carson Sink, which is underlain by deposits of Lake Lahontan. The bordering mountain ranges to the west and south are of low relief and underlain largely by Tertiary volcanic and sedimentary units. Pre-Tertiary rocks are extensively exposed east of the Carson Sink in the Stillwater Range, Clan Alpine Mountains, Augusta Mountains, and New Pass Mountains. The eastern valleys are underlain by Quaternary alluvial and lacustrine deposits contemporaneous with the western deposits of Lake Lahontan. The eastern mountain ranges are more rugged than the western ranges and have higher relief; the eastern valleys are generally narrower.

Global Tsunami Database: Adding Geologic Deposits, Proxies, and Tools

NASA Astrophysics Data System (ADS)

Brocko, V. R.; Varner, J.

2007-12-01

A result of collaboration between NOAA's National Geophysical Data Center (NGDC) and the Cooperative Institute for Research in the Environmental Sciences (CIRES), the Global Tsunami Database includes instrumental records, human observations, and now, information inferred from the geologic record. Deep Ocean Assessment and Reporting of Tsunamis (DART) data, historical reports, and information gleaned from published tsunami deposit research build a multi-faceted view of tsunami hazards and their history around the world. Tsunami history provides clues to what might happen in the future, including frequency of occurrence and maximum wave heights. However, instrumental and written records commonly span too little time to reveal the full range of a region's tsunami hazard. The sedimentary deposits of tsunamis, identified with the aid of modern analogs, increasingly complement instrumental and human observations. By adding the component of tsunamis inferred from the geologic record, the Global Tsunami Database extends the record of tsunamis backward in time. Deposit locations, their estimated age and descriptions of the deposits themselves fill in the tsunami record. Tsunamis inferred from proxies, such as evidence for coseismic subsidence, are included to estimate recurrence intervals, but are flagged to highlight the absence of a physical deposit. Authors may submit their own descriptions and upload digital versions of publications. Users may sort by any populated field, including event, location, region, age of deposit, author, publication type (extract information from peer reviewed publications only, if you wish), grain size, composition, presence/absence of plant material. Users may find tsunami deposit references for a given location, event or author; search for particular properties of tsunami deposits; and even identify potential collaborators. Users may also download public-domain documents. Data and information may be viewed using tools designed to extract and

Aeromagnetometry of the El Papalote H12A-13 Chart Northwestern Sonora, México: Relationships to Regional Geology and Mineral Deposits

NASA Astrophysics Data System (ADS)

Martinez-Retama, S.; Pérez-Segura, E.; Vega-Granillo, R.

2014-12-01

This study is focused in obtaining a geophysical-geological characterization of magnetic anomalies associated with outcropping or buried rock bodies and its possible relation to ore deposits. To do this, total field aeromagnetic data from the Mexican Geological Survey were processed. Reduction to pole and residual anomaly maps show two main elongated dipolar high-amplitude anomalies, a first NE-SW directed, which is located in the NW portion of the card, and a second corresponding to a belt with NW-SE direction that is located SW of the chart, near the eastern region of the "El Elegante" volcano. Above structures have not been mapped in the surface; however, the well-defined magnetic anomalies indicate its existence below Quaternary sediments. The geology of the chart is only partially known. The outcropping units, mostly in the Sierra de Los Tanques, are Paleoproterozoic igneous and metamorphic rocks; Permian-Triassic granitoids; and Jurassic and Tertiary volcanic and volcanosedimentary rocks. About 50% of the card is covered by Quaternary sediments, there the interest of these geophysical studies. The NW-SE oriented deep magnetic anomaly follows the same direction as the Sierra San Francisco (SSF) located south of Los Norteños chart H12A-2. This mountain is composed of Paleoproterozoic metamorphic rocks intruded by Upper Cretaceous granitoids. Numerous mineral manifestations of orogenic gold type occurred in that range. This anomaly can be interpreted in 2 ways: first: as a NW extension of a landform similar to the SSF, which dips to NW or that is more erosionated; or; second: as an extension of the SSF to the NW displaced by a normal fault oriented ~N60E, roughly following the Palo Fierro creek indicated on the map. Either of the two possible interpretations, the magnetic anomaly indicates an interesting target in the search of orogenic gold deposits that could be buried in the area.

Geology and geochemistry of Summitville, Colorado: an epithermal acid sulfate deposit in a volcanic dome

USGS Publications Warehouse

Gray, J.E.; Coolbaugh, M.F.

1994-01-01

Geologic studies during recent open-pit mining at Summitville, Colorado, have provided new information on an epithermal acid sulfate Au-Ag-Cu deposit formed in a volcanic dome. Geologic mapping, geochemical studies of whole-rock samples from blast holes, and geologic and geochemical traverse studies refine the details of the evolution of the Summitville deposit. Six distinct events followed emplacement of the quartz latite volcanic dome and define the development of the Summitville deposit: 1) an early stage of acid sulfate alteration, 2) subsequent Cu sulfide and gold mineralization, 3) widespread hydrothermal brecciation, 4) volumetrically minor, base metal sulfide-bearing barite veining, 5) volumetrically minor, kaolinite matrix brecciation, and finally, 6) supergene oxidation. -from Authors

Characterization and timing of the different types of fluids present in the barren and ore-veins of the W-Sn deposit of Panasqueira, Central Portugal

NASA Astrophysics Data System (ADS)

Noronha, F.; Doria, A.; Dubessy, J.; Charoy, B.

1992-01-01

The Panasqueira W-Sn deposit is the largest quartz-vein type deposit of the Iberian Peninsula and the most important wolframite deposit in Western Europe. The ore-veins are almost exclusively sub-horizontal. Besides ore-bearing sub-horizontal veins, the Panasqueira mine also contains barren quartz veins. There are essentially two generations of barren quartz: quartz, contemporaneous with the earliest regional metamorphism (QI), and recrystallized quartz, contemporaneous with the thermal metamorphism related to the granite intrusion (QII). Fluid inclusion studies (microthermometry and Raman) were undertaken in order to distinguish fluids contemporaneous with the barren quartz from those contemporaneous with the ore-bearing quartz (QIII). Fluid inclusion data indicate that the barren and ore-bearing quartz fluids are dominantly aqueous (93 to 98 mol% H2O), with a nearly constant bulk salinity (8 to 12 wt% eq. NaCl), with the quantity of volatile component (determined by Raman spectrometry) higher in QIII, but never greater than 5 mol%. However, the CO2/CH4 + N2 ratio is different for each type of quartz. Volatiles are dominated by CH4 (10 to 96 mol% ZCH4 and/or N2 (3 to 87 mol% ZN2) in the barren quartz and by CO2 (60 to 73 mol% ZCO2) in ore-bearing quartz. The bulk chemical composition of the fluids in QIII is comparable to that found commonly in hydrothermal fluids associated with wolframite mineralization, where Na>K>Ca and HCO3>Cl>SO4. A dispersion in TH (226 to 350 °C) found in QIII, together with a variation in the degree of filling (0.5 to 0.7) and with the consequent variation of fluid densities (0.70 to 0.79), may result from changes in the fluid pressure regime below lithostatic pressure, suggesting vein filling related to tectonic events.

The composition of fluid inclusions in ore and gangue minerals from the Silesian-Cracow Mississippi Valley-type Zn-Pb deposits Poland: Genetic and environmental implications

USGS Publications Warehouse

Viets, J.G.; Hofstra, A.H.; Emsbo, P.; Kozlowski, A.

1996-01-01

The composition of fluids extracted from ore and gangue sulfide minerals that span most of the paragenesis of the Silesian-Cracow district was determined using a newly developed ion chromatographic (IC) technique. Ionic species determined were Na+, NH+4, Ca2+, Mg2+, K+, Rb+, Sr2+, Ba2+, Cl-, Br-, F-, I-, PO3-4, CO2-3, HS-, S2O2-3, SO2-4, NO-3, and acetate. Mineral samples included six from the Pomorzany mine and one from the Trzebionka mine which are hosted in the Triassic Muschelkalk Formation, and two samples of drill core from mineralized Upper Devonian strata. Nine paragenetically identifiable sulfide minerals occur throughout the Silesian-Cracow district. These include from earliest to latest: early iron sulfides, granular sphalerite, early galena, light-banded sphalerite, galena, dark-banded sphalerite, iron sulfides, late dark-banded sphalerite with late galena, and late iron sulfides. Seven of the minerals were sampled for fluid inclusion analysis in this study. Only the early iron sulfides and the last galena stage were not sampled. Although the number of analyses are limited to nine samples and two replicates and there is uncertainty about the characteristics of the fluid inclusions analyzed, the data show clear temporal trends in the composition of the fluids that deposited these minerals. Fluid inclusions in minerals deposited later in the paragenesis have significantly more K+, Br-, NH+4, and acetate but less Sr2+ than those deposited earlier in the paragenesis. The later minerals are also characterized by isotopically lighter sulfur and significantly more Tl and As in the solid minerals. The change in ore-fluid chemistry is interpreted to reflect a major change in the hydrologic regime of the district. Apparently, the migrational paths of ore fluids from the Upper Silesian basin changed during ore deposition and the fluids which deposited early minerals reacted with aquifers with very different geochemical characteristics than those that deposited

New approaches in geological studies of tsunami deposits

NASA Astrophysics Data System (ADS)

Szczucinski, Witold

2017-04-01

During the last dozen of years tsunamis have appeared to be the most disastrous natural process worldwide. The dramatic, large tsunamis on Boxing Day, 2004 in the Indian Ocean and on March 11, 2011 offshore Japan caused catastrophes listed as the worst in terms of the number of victims and the economic losses, respectively. In the aftermath, they have become a topic of high public and scientific interest. The record of past tsunamis, mainly in form of tsunami deposits, is often the only way to identify tsunami risk at a particular coast due to relatively low frequency of their occurrence. The identification of paleotsunami deposits is often difficult mainly because the tsunami deposits are represented by various sediment types, may be similar to storm deposits or altered by post-depositional processes. There is no simple universal diagnostic set of criteria that can be applied to interpret tsunami deposits with certainty. Thus, there is a need to develop new methods, which would enhance 'classical', mainly sedimentological and stratigraphic approach. The objective of the present contribution is to show recent progress and application of new approaches including geochemistry (Chagué-Goff et al. 2017) and paleogenetics (Szczuciński et al. 2016) in studies of geological impacts of recent tsunamis from various geographical regions, namely in monsoonal-tropical, temperate and polar zones. It is mainly based on own studies of coastal zones affected by 2004 Indian Ocean Tsunami in Thailand, 2011 Tohoku-oki tsunami and older paleotsunamis in Japan, catastrophic saltwater inundations at the coasts of Baltic Sea and 2000 landslide-generated tsunami in Vaigat Strait (west Greenland). The study was partly funded by Polish National Science Centre grant No. 2011/01/B/ST10/01553. Chagué-Goff C., Szczuciński W., Shinozaki T., 2017. Applications of geochemistry in tsunami research: A review. Earth-Science Reviews 165: 203-244. Szczuciński W., Pawłowska J., Lejzerowicz F

Map showing potential metal-mine drainage hazards in Colorado, based on mineral-deposit geology

USGS Publications Warehouse

Plumlee, Geoffrey S.; Streufert, Randall K.; Smith, Kathleen S.; Smith, Steven M.; Wallace, Alan R.; Toth, Margo I.; Nash, J. Thomas; Robinson, Rob A.; Ficklin, Walter H.; Lee, Gregory K.

1995-01-01

This map, compiled by the U.S. Geological Survey (USGS) in cooperation with the Colorado Geological Survey (CGS) and the U. S. Bureau of Land Management (BLM), shows potential mine-drainage hazards that may exist in Colorado metal-mining districts, as indicated by the geologic characteristics of the mineral deposits that occur in the respective districts. It was designed to demonstrate how geologic and geochemical information can be used on a regional scale to help assess the potential for mining-related and natural drainage problems in mining districts, unmined mineralized areas, and surrounding watersheds. The map also provides information on the distribution of different mineral deposit types across Colorado. A GIS (Geographic Information System) format was used to integrate geologic, geochemical, water-quality, climate, landuse, and ecological data from diverse sources. Likely mine-drainage signatures were defined for each mining district based on: (1) a review of the geologic characteristics of the mining district, including mineralogy, trace-element content, host-rock lithology, and wallrock alteration, and; (2) results of site specific studies on the geologic controls on mine-drainage composition.

International Project - Atlas of Geological Maps of Central Asia and Adjacent Territories 1:2 500 000 Scale - the Status and the Development Prospects

NASA Astrophysics Data System (ADS)

Leonov, Y.; Petrov, O. V.; Dong, S.; Morozov, A.; Shokalsky, S.; Pospelov, I.; Erinchek, Y.; Milshteyn, E.

2011-12-01

This project is launched by geological surveys of Russia, China, Mongolia, Kazakhstan and the Republic of Korea with participation of National Academies of Sciences under the aegis of the Commission for the Geological Map of the World since 2004. The project goal is the compilation and subsequent monitoring of the set of digital geological maps for the large part of the Asian continent (20 million km2). Each country finances its own part of the project while all the issues concerning methods and technologies are discussed collectively during annual meetings and joint filed excursions. At the 33d IGC, were shown 4 digital maps of the Atlas at 1: 2,5M - geological, tectonic, metallogenic and energy resources. Geological and energy resources maps were compiled and published by the Chinese part while tectonic and metallogenic maps by Russian side (VSEGEI, Saint-Petersburg). The geological map was also used as the base for the compilation of the other maps of the Atlas. On the tectonic map colours indicate several stages of the continental crust consolidation within fold belts, their tectonic reworking and rifting. The map also shows rock complexes-indicators of geodynamic settings. In the platform areas, the colour reflects the time of beginning of the sedimentary cover formation while its shades reflect the thickness of the sediments. The metallogenic map of the Atlas depicts 1380 objects of metallogenic zoning (from super-provinces to ore clusters) and is accompanied with a database (more than 5000 ore deposits). The map of energy resources with the database contains information on the of coal- and oil-and-gas-bearing basins and main coal and hydrocarbon deposits. In 2009 the study area was extended to the North, East and South in order to embrace bigger territory with ore-bearing Mesozoic-Cenozoic volcanic belts of the Asian continent's Pacific margin. According to nearest plans, discussed with the head of Rosnedra Dr. Anatoliy Ledovskikh and the director of the

Relation of ERTS-1 detected geologic structure to known economic ore deposits

NASA Technical Reports Server (NTRS)

Rich, E. I.

1973-01-01

A preliminary analysis of ERTS-1 imagery of the Northern Coast Ranges and Sacramento Valley, California, has disclosed a potentially important fracture system which may be one of the controlling factors in the location of known mercury deposits in the Coast Ranges and which appears to be associated with some of the oil and gas fields within the Sacramento Valley. Recognition of this fracture system may prove to be an extremely useful exploration tool, hence careful analysis of subsequent ERTS imagery might delineate areas for field evaluation.

First discovery of high-mercury silver in ores of the Rogovik gold-silver deposit (Northeastern Russia)

NASA Astrophysics Data System (ADS)

Makshakov, A. S.; Kravtsova, R. G.; Goryachev, N. A.; Pal'yanova, G. A.; Pavlova, L. A.

2017-09-01

New data on mercurial mineralization are presented, and a detailed characteristic is given for the first discovery of mercurous silver in ores of the Rogovik gold-silver deposit (the Omsukchan trough, Northeastern Russia). It was found that native silver in the examined ores occurs as finely-dispersed inclusions in quartz filling microcracks and interstitions. It also occurs in associations with kustelite, Ag sulfosalts and selenides, selenitic acanthite, and argyrodite. The mercury admixture varies from "not detected" in the central parts of grains to 0.22-1.70 wt % along the edges, or, in independent grains, to the appearance of Ag amalgams containing 10.20-24.61 wt % of Hg. The xenomorph form of grains of 50 μm or less in size prevails. It is assumed that the appearance of mercurial mineralization is caused by the superposition of products of the young Hg-bearing Dogda-Erikit belt upon the more ancient Ag-bearing Omsukchan trough.

The Influences of Geologic Depositional Environments on Sand Boil Development, Tara Wildlife Lodge Area in Mississippi

DTIC Science & Technology

2016-03-01

ER D C/ G SL T R- 16 -7 The Influences of Geologic Depositional Environments on Sand Boil Development, Tara Wildlife Lodge Area in...client/default. ERDC/GSL TR-16-7 March 2016 The Influences of Geologic Depositional Environments on Sand Boil Development, Tara Wildlife Lodge...Army Corps of Engineers Washington, DC 20314-1000 ERDC/GSL TR-16-7 ii Abstract A comprehensive study of the subsurface geology in the Tara Wildlife

Probabilistic estimates of number of undiscovered deposits and their total tonnages in permissive tracts using deposit densities

USGS Publications Warehouse

Singer, Donald A.; Kouda, Ryoichi

2011-01-01

Empirical evidence indicates that processes affecting number and quantity of resources in geologic settings are very general across deposit types. Sizes of permissive tracts that geologically could contain the deposits are excellent predictors of numbers of deposits. In addition, total ore tonnage of mineral deposits of a particular type in a tract is proportional to the type’s median tonnage in a tract. Regressions using size of permissive tracts and median tonnage allow estimation of number of deposits and of total tonnage of mineralization. These powerful estimators, based on 10 different deposit types from 109 permissive worldwide control tracts, generalize across deposit types. Estimates of number of deposits and of total tonnage of mineral deposits are made by regressing permissive area, and mean (in logs) tons in deposits of the type, against number of deposits and total tonnage of deposits in the tract for the 50th percentile estimates. The regression equations (R2 = 0.91 and 0.95) can be used for all deposit types just by inserting logarithmic values of permissive area in square kilometers, and mean tons in deposits in millions of metric tons. The regression equations provide estimates at the 50th percentile, and other equations are provided for 90% confidence limits for lower estimates and 10% confidence limits for upper estimates of number of deposits and total tonnage. Equations for these percentile estimates along with expected value estimates are presented here along with comparisons with independent expert estimates. Also provided are the equations for correcting for the known well-explored deposits in a tract. These deposit-density models require internally consistent grade and tonnage models and delineations for arriving at unbiased estimates.

Numerical Modeling of Multiphase Fluid Flow in Ore-Forming Hydrothermal Systems

NASA Astrophysics Data System (ADS)

Weis, P.; Driesner, T.; Coumou, D.; Heinrich, C. A.

2007-12-01

Two coexisting fluid phases - a variably saline liquid and a vapor phase - are ubiquitous in ore-forming and other hydrothermal systems. Understanding the dynamics of phase separation and the distinct physical and chemical evolution of the two fluids probably plays a key role in generating different ore deposit types, e.g. porphyry type, high and low sulfidation Cu-Mo-Au deposits. To this end, processes within hydrothermal systems have been studied with a refined numerical model describing fluid flow in transient porous media (CSP~5.0). The model is formulated on a mass, energy and momentum conserving finite-element-finite-volume (FEFV) scheme and is capable of simulating multiphase flow of NaCl-H20 fluids. Fluid properties are computed from an improved equation of state (SOWAT~2.0). It covers conditions with temperatures of up to 1000 degrees~C, pressures of up to 500 MPa, and fluid salinities of 0~to 100%~NaCl. In particular, the new set-up allows for a more accurate description of fluid phase separation during boiling of hydrothermal fluids into a vapor and a brine phase. The geometric flexibility of the FEFV-meshes allows for investigations of a large variety of geological settings, ranging from ore-forming processes in magmatic hydrothermal system to the dynamics of black smokers at mid-ocean ridges. Simulations demonstrated that hydrothermal convection patterns above cooling plutons are primarily controlled by the system-scale permeability structure. In porphyry systems, high fluid pressures develop in a stock rising from the magma chamber which can lead to rock failure and, eventually, an increase in permeability due to hydrofracturing. Comparisons of the thermal evolution as inferred from modeling studies with data from fluid inclusion studies of the Pb-Zn deposits of Madan, Bulgaria are in a strikingly good agreement. This indicates that cross-comparisons of field observations, analytical data and numerical simulations will become a powerful tool towards a

Geology and geochemistry of jasperoids from the Gold Bar district, Nevada

USGS Publications Warehouse

Yigit, O.; Hofstra, A.H.; Hitzman, M.W.; Nelson, E.P.

2006-01-01

Gold Bar is one of several Carlin-type gold mining districts located in the Battle Mountain-Eureka trend, Nevada. It is composed of one main deposit, Gold Bar; five satellite deposits; and four resources that contain 1.6 Moz (50 t) of gold. All of the deposits and resources occur at the intersection of north-northwest- and northeast-trending high-angle faults in slope facies limestones of the Devonian Nevada Group exposed in windows through Ordovician basin facies siliciclastic rocks of the Roberts Mountains allochthon. Igneous intrusions and magnetic anomalies are notably absent. The Gold Bar district contains a variety of discordant and stratabound jasperoid bodies, especially along the Wall Fault zone, that were mapped and studied in some detail to identify the attributes of those most closely associated with gold ore and to constrain genetic models. Four types of jasperoids, J0, J1, J2, and J3, were distinguished on the basis of their geologic and structural settings and appearance. Field relations suggest that J0 formed during an early event. Petrographic observations, geochemistry, and ??18O values of quartz suggest it was overprinted by the hydrothermal event that produced ore-related J1, J2, and J3 jasperoids and associated gold deposits. The greater amount of siliciclastic detritus present in J0 jasperoids caused them to have higher ??18O values than J1,2,3 jasperoids hosted in underlying limestones. Ore-related jasperoids are composed of main-ore-stage replacements and late-ore-stage open-space filling quartz with variable geochemistry and an enormous range of ??18O values (24.5 and -3.7???). Jasperoids hosted in limestones with the most anomalous Au, Ag, Hg, ??(As, Sb, Tl) concentrations and the highest ??18O values are associated with the largest deposits. The 28??? range of jasperoid ??18O values is best explained by mixing between an 18O-enriched fluid and an 18O-depleted fluid. The positive correlation between the sizes of gold deposits and the ??18O

Raman Spectroscopic Characterisation of Australian Banded Iron Formation and Iron Ore

NASA Astrophysics Data System (ADS)

Wells, M. A.; Ramanaidou, E. R.

2012-04-01

In Australia and world-wide over the past 5-10 years, declining reserves of premium, high-grade (>64% Fe), low-P bearing iron ore, have seen iron ore producers increase their utilisation of lower Fe-grade, higher P/Al/Si ore. In Australia, the channel iron deposits (CID), bedded iron deposits (BID) and, more recently, BIF-derived magnetite iron deposits (MID) have seen increased usage driven mainly by the increased demand from Chinese steel mills (Ramanaidou and Wells, 2011). Efficient exploitation and processing of these lower-grade iron ores requires a detailed understanding of their iron oxide and gangue mineralogy and geochemistry. The common Fe-bearing minerals (e.g., hematite, magnetite, goethite and kenomagnetite) in these deposits, as well as gangue minerals such as quartz and carbonates, are all strongly Raman active (e.g., de Faria et al., 1997). Their distinct Raman spectra enable them to be easily detected and mapped in situ in either unprepared material or samples prepared as polished blocks. In this paper, using representative examples of Australian CID ore, martite-goethite bedded iron deposit (BID) ore and banded iron formation (BIF) examined as polished blocks, we present a range of Raman spectra of the key iron ore minerals, and discuss how Raman spectroscopy can be applied to characterising iron ore mineralogy. Raman imaging micrographs, obtained using a StreamLine Plus Raman imaging system, clearly identified the main Fe-oxide and gangue components in the CID, BID and BIF samples when compared to optical micrographs. Raman analysis enabled the unequivocal identification of diamond in the CID ore as a contaminant from the polishing paste used to prepare the sample, and confirmed the presence of hematite in the BID ore in the form of martite, which can be morphologically similar to magnetite and, thus, difficult to otherwise distinguish. Image analysis of Raman mineral maps could be used to quantify mineral abundance based on the number of 'pixels

Genesis of iron-apatite ores in Posht-e-Badam Block (Central Iran) using REE geochemistry

NASA Astrophysics Data System (ADS)

Mokhtari, Mir Ali Asghar; Zadeh, Ghader Hossein; Emami, Mohamad Hashem

2013-06-01

Rare earth elements in apatites of different ore types show characteristic patterns which are related to different modes of formation of the ores. Most of the apatite-bearing iron ores are associated with alkaline magmas with LREE/HREE fractionation varying from moderate to steep. Iron-apatite deposits in Posht-e-Badam Block (Central Iran) have a high concentration of REE (more than 1000 ppm up to 2.5%), and show a strong LREE/HREE ratio with a pronounced negative Eu anomaly. This REE pattern is typical of magmatic apatite and quiet distinct from sedimentary apatites (phosphorites) which have a low REE contents and Ce negative anomalies. On the other hand, they are comparable to the REE patterns of apatites in Kiruna-type iron ores in different parts of the world. The REE patterns of apatites, iron-apatite ores and iron ores are similar and only have different REE contents. This similarity indicates a genetic relation for these rocks. Most of the iron-apatite deposits in Central Iran have similar REE patterns too, which in turn show a genetic relation for all of these deposits. This similarity indicates a similar origin and processes in their genesis. There are some small intrusions around some of the iron-apatite deposits that are petrographically identified as syenite and gabbro. These intrusions also have REE patterns similar to that of iron-apatite ores. This demonstrates a genetic relation between these intrusions and iron-apatite ores. The REE patterns of apatites in different deposits of Posht-e-Badam Block iron-apatite ores show an affinity to alkaline to sub-alkaline magmas and rifting environment. The alkaline host rocks of Central Iran iron-apatite ores are clearly related to an extensional setting where rifting was important (SSE-NNW fault lines). A probable source for this large scale ore forming processes is relatively low partial melting of mantle rocks. The ores have originated by magmatic differentiation as a late phase in the volcanic cycle

Geology and origin of epigenetic lode gold deposits, Tintina Gold Province, Alaska and Yukon: Chapter A in Recent U.S. Geological Survey studies in the Tintina Gold Province, Alaska, United States, and Yukon, Canada--results of a 5-year project

USGS Publications Warehouse

Goldfarb, Richard J.; Marsh, Erin E.; Hart, Craig J.R.; Mair, John L.; Miller, Marti L.; Johnson, Craig; Gough, Larry P.; Day, Warren C.

2007-01-01

-rich and 18O-rich crustal fluids, most commonly of low salinity. The older group of ores includes the low-grade intrusion-related gold systems at Fort Knox near Fairbanks and those in Yukon, with fluids exsolved from fractionating melts at depths of 3 to 9 kilometers and forming a zoned sequence of auriferous mineralization styles extending outward to the surrounding metasedimentary country rocks. The causative plutons are products of potassic mafic magmas generated in the subcontinental lithospheric mantle that interacted with overlying lower to middle crust to generate the more felsic ore-related intrusions. In addition, the older ores include spatially associated, high-grade, shear-zonerelated orogenic gold deposits formed at the same depths from upward-migrating metamorphic fluids; the Pogo deposit is a relatively deep-seated example of such. The younger gold ores, restricted to southwestern Alaska, formed in unmetamorphosed sedimentary rocks of the Kuskokwim basin within 1 to 2 kilometers of the surface. Most of these deposits formed via fluid exsolution from shallowly emplaced, highly evolved igneous complexes generated mainly as mantle melts. However, the giant Donlin Creek orogenic gold deposit is a product of either metamorphic devolatilization deep in the basin or of a gold-bearing fluid released from a flysch-melt igneous body.

SEDIMENT-HOSTED PRECIOUS METAL DEPOSITS.

USGS Publications Warehouse

Bagby, W.C.; Pickthorn, W.J.; Goldfarb, R.; Hill, R.A.

1984-01-01

The Dee mine is a sediment-hosted, disseminated gold deposit in the Roberts Mountains allochthon of north central Nevada. Soil samples were collected from the C-horizon in undisturbed areas over the deposit in order to investigate the usefulness of soil geochemistry in identifying this type of deposit. Each sample was sieved to minus 80 mesh and analyzed quantitatively for Au, Ag, As, Sb, Hg, Tl and semi-quantitative data for an additional 31 elements. Rank sum analysis is successful for the Au, Ag, As, Sb, Hg, Tl suite, even though bedrock geology is disregarded. This method involves data transformation into a total element signature by ranking the data in ascending order and summing the element ranks for each sample. The rank sums are then divided into percentile groups and plotted. The rank sum plot for the Dee soils unequivocally identifies three of four known ore zones.

Geology of the Shinarump No. 1 uranium mine, Seven Mile Canyon area, Grand County, Utah

USGS Publications Warehouse

Finch, Warren Irvin

1953-01-01

The Shinarump No. 1 uranium mine is located about 12 miles northwest of Moab, Utah, in the Seven Mile Canyon area, Grand County, Utah. A study was made of the geology of the Shinarump No. 1 mine in order to determine the habits, ore controls, and possible origin of the deposit. Rocks of Permain, Triassic, and Jurassic age crop out in the area mapped. Uranium deposits are found in three zones in the lower 25 feet of the Upper Triassic Chinle formation. The Shinarump No. 1 mine, which is in the lowermost zone, is located on the west flank of the Moab anticline near the Moab fault. The Shinarump No. 1 uranium deposit consists of discontinuous lenticular layers of mineralized rock, irregular in outline, that, in general, follow the bedding. Ore minerals, mainly uranite, impregnate the rock. High-grade seams of uranite and chalcocite occur along bedding planes. Formation of unraninite is later than or simultaneous with most sulfides. Chalcocite may be of two ages, with some being later than uraninite. Uraninite and chalcocite are concentrated in the poorer sorted parts of siltstones. Guides to ore in the Seven Mile Canyon area inferred from the study of the Shinarump No. 1 deposit are the presence of bleached siltstone, copper sulfides, and carbonaceous matter. Results of spectrographic analysis indicated that the mineralizing solutions contained important amounts of barium, vanadium, uranium, and copper as well as lesser amounts of strontium, chromium, boron, yttrium, lead, and zinc. The origin of the Shinarump No. 1 deposit is thought to be hydrothermal, dated as later or early.

Magnetite as the indicator of ore genesis for the Huangshaping polymetallic deposit, southern Hunan Province, China

NASA Astrophysics Data System (ADS)

Ding, T.; Ma, D.; Lu, J.; Zhang, R.

2017-12-01

Huangshaping polymetallic deposit, located in southern Hunan Province, China, hosts abundant W-Mo-Pb-Zn mineralization which linked with the skarn system located between late Mesozoic high-K calc-alkaline to shoshonitic granitoids and the Carboniferous carbonate in this deposit. In this study, concentrations of trace and minor elements of the magnetites from different skarn stages are obtained by in situ LA-ICP-MS analysis, in order to further understand the polymetallic mineralization processes within this deposit. The generally high concentrations of spinel elements, including Mg, Al, Ti, Mn, V, Cr, Co, Ni, Ga, Ge, and Sn, in all magnetites from this deposit suggest that these elements are incorporated into magnetite lattice by substituting Fe3+ and/or Fe2+. However, the various concentrations of Na, Si, K, Ca, and W elements in magnetites, combining the abnormal time-resolved analytical signals of LA-ICP-MS analyses, suggest that these elements are significantly affected by the fluid inclusions in magnetites. Two groups of magnetites can be further distinguished based on their trace and minor elements concentrations: Group-1 magnetites, including those in medium grain garnets and calcite, have obvious lower Na, Si, K, Ca, Sn, W, but higher Mg, Al, Ti, V, Co, Ni, Zn concentrations compared with Group-2 magnetites, which including those in coarse grain garnets, tremolite, and bulk magnetite ores. This suggests that the hydrothermal fluids where Group-2 magnetites precipitated are evolved magmatic fluids which have undergone the crystal fractionation during the early skarn stages (eg. Garnet and tremolite), the high Na, Si, K, and Ca in the hydrothermal fluids probably result from the dissolution of the host rocks, such as limestone, sandstone, and evaporite horizons in this deposit. However, the Group-1 magnetites probably precipitated in the hydrothermal fluids with low salinity, which result the low Na, Si, K, and Ca in these magnitites. Furthermore, these

Geophysical model of the Cu-Mo porphyry ore deposit at Copper Flat Mine, Hillsboro, Sierra County, New Mexico

NASA Astrophysics Data System (ADS)

Gutierrez, Adrian Emmanuel Gutierrez

A 3D gravity model of the Copper Flat Mine was performed as part of the exploration of new resources in at the mine. The project is located in the Las Animas Mining District in Sierra County, New Mexico. The mine has been producing ore since 1877 and is currently owned by the New Mexico Copper Corporation, which plans o bringing the closed copper mine back into production with innovation and a sustainable approach to mining development. The Project is located on the Eastern side of the Arizona-Sonora-New Mexico porphyry copper Belt of Cretaceous age. Copper Flat is predominantly a Cretaceous age stratovolcano composed mostly of quartz monzonite. The quartz monzonite was intruded by a block of andesite alter which a series of latite dikes creating veining along the topography where the majority of the deposit. The Copper Flat deposit is mineralized along a breccia pipe where the breccia is the result of auto-brecciation due to the pore pressure. There have been a number of geophysical studies conducted at the site. The most recent survey was a gravity profile on the area. The purpose of the new study is the reinterpretation of the IP Survey and emphasizes the practical use of the gravity geophysical method in evaluating the validity of the previous survey results. The primary method used to identify the deposit is gravity in which four Talwani models were created in order to created a 3D model of the ore body. The Talwani models have numerical integration approaches that were used to divide every model into polygons. The profiles were sectioned into polygons; each polygon was assigning a specific density depending on the body being drawn. Three different gridding techniques with three different filtering methods were used producing ten maps prior to the modeling, these maps were created to establish the best map to fit the models. The calculation of the polygons used an exact formula instead of the numerical integration of the profile made with a Talwani approach. A

The geologic relationships of industrial mineral deposits and asbestos in the western united states

USGS Publications Warehouse

VanGosen, B.S.

2009-01-01

In recent years, U.S. regulatory agencies have placed emphasis on identifying and regulating asbestos dust exposures in the mining environment, with a particular focus upon industrial mineral deposits in which asbestos occurs as an accessory mineral. Because asbestos minerals form in specific geologic environments, only certain predictable types of industrial mineral deposits can potentially host asbestos mineralization. By applying a basic knowledge of asbestos geology, the costly and time consuming efforts of asbestos monitoring and analyses can be directed towards those mineral deposit types most likely to contain asbestos mineralogy, while saving efforts on the mineral deposits that are unlikely to contain asbestos. While the vast majority of industrial mineral deposits in the Western United States are asbestos-free, there are several types that can, in some instances, host asbestos mineralization, or be closely associated with it. These industrial mineral deposits include a few types of aggregate, dimension, and decorative stone, and some deposits of chromite-nickel, magnesite, nepheline syenite, olivine, rare earth elements, talc, vermiculite, and wollastonite.

Boron isotope evidence for the involvement of non-marine evaporites in the origin of the Broken Hill ore deposits

USGS Publications Warehouse

Slack, J.F.; Palmer, M.R.; Stevens, B.P.J.

1989-01-01

IDENTIFYING the palaeogeographic setting and mode of origin of stratabound ore deposits can be difficult in high-grade metamorphic terranes, where the effects of metamorphism may obscure the nature of the protoliths. Here we report boron isotope data for tourmalines from the early Proterozoic Broken Hill block, in Australia, which hosts giant lead-zinc-silver sulphide deposits. With one exception the 11B/10B ratios are lower than those for all other tourmalines from massive sulphide deposits and tour-malinites elsewhere in the world. We propose that these low ratios reflect leaching of boron from non-marine evaporitic borates by convecting hydrothermal fluids associated with early Proterozoic continental rifting. A possible modern analogue is the Salton Sea geothermal field in California. ?? 1989 Nature Publishing Group.

The 16th International Geological Congress, Washington, 1933

USGS Publications Warehouse

Nelson, C.M.

2009-01-01

In 1933, the International Geological Congress (IGC) returned to the United States of America (USA) for its sixteenth meeting, forty-two years after the 5th IGC convened in Washington. The Geological Society of America and the U.S. Geological Survey (USGS) supplied the major part of the required extra-registration funding after the effects of the Great Depression influenced the 72th U.S. Congress not to do so. A reported 1, 182 persons or organizations, representing fifty-four countries, registered for the 16 th IGC and thirty-four countries sent 141 official delegates. Of the total number of registrants, 665 actually attended the meeting; 500 came from the USA; and fifteen had participated in the 5th IGC. The 16 th Meeting convened in the U.S. Chamber of Commerce Building from 22 to 29 July. The eighteen half-day scientific sections-orogenesis (four), major divisions of the Paleozoic (three), miscellaneous (three), batholiths and related intrusives (two), arid-region geomorphic processes and products (one), fossil man and contemporary faunas (one), geology of copper and other ore deposits (one), geology of petroleum (one), measuring geologic time (one), and zonal relations of metalliferous deposits (one)-included 166 papers, of which fifty (including several of the key contributions) appeared only by title. The Geological Society of Washington, the National Academy of Sciences, and the U.S. Bureau of Mines hosted or contributed to evening presentations or receptions. Twenty-eight of the 16th IGC's thirty new guidebooks and one new USGS Bulletin aided eight pre-meeting, seven during-meeting, and four post-meeting field trips of local, regional, or national scope. The remaining two new guidebooks outlined the USA's structural geology and its stratigraphic nomenclature. The 16th IGC published a two-volume monograph on the world's copper resources (1935) and a two-volume report of its proceedings (1936).

3&4D Geomodeling Applied to Mineral Resources Exploration - A New Tool for Targeting Deposits.

NASA Astrophysics Data System (ADS)

Royer, Jean-Jacques; Mejia, Pablo; Caumon, Guillaume; Collon-Drouaillet, Pauline

2013-04-01

3 & 4D geomodeling, a computer method for reconstituting the past deformation history of geological formations, has been used in oil and gas exploration for more than a decade for reconstituting fluid migration. It begins nowadays to be applied for exploring with new eyes old mature mining fields and new prospects. We describe shortly the 3&4D geomodeling basic notions, concepts, and methodology when applied to mineral resources assessment and modeling ore deposits, pointing out the advantages, recommendations and limitations, together with new challenges they rise. Several 3D GeoModels of mining explorations selected across Europe will be presented as illustrative case studies which have been achieved during the EU FP7 ProMine research project. It includes: (i) the Cu-Au porphyry deposits in the Hellenic Belt (Greece); (ii) the VMS in the Iberian Pyrite Belt including the Neves Corvo deposit (Portugal) and (iii) the sediment-hosted polymetallic Cu-Ag (Au, PGE) Kupferschiefer ore deposit in the Foresudetic Belt (Poland). In each case full 3D models using surfaces and regular grid (Sgrid) were built from all dataset available from exploration and exploitation including geological primary maps, 2D seismic cross-sections, and boreholes. The level of knowledge may differ from one site to another however those 3D resulting models were used to pilot additional field and exploration works. In the case of the Kupferschiefer, a sequential restoration-decompaction (4D geomodeling) from the Upper Permian to Cenozoic was conducted in the Lubin- Sieroszowice district of Poland. The results help in better understanding the various superimposed mineralization events which occurred through time in this copper deposit. A hydro-fracturing index was then calculated from the estimated overpressures during a Late Cretaceous-Early Paleocene up-lifting, and seems to correlate with the copper content distribution in the ore-series. These results are in agreement with an Early Paleocene

Late-kinematic timing of orogenic gold deposits and significance for computer-based exploration techniques with emphasis on the Yilgarn Block, Western Australia

USGS Publications Warehouse

Groves, D.I.; Goldfarb, R.J.; Knox-Robinson, C. M.; Ojala, J.; Gardoll, S.; Yun, G.Y.; Holyland, P.

2000-01-01

Orogenic gold deposits are a widespread coherent group of epigenetic ore deposits that are sited in accretionary or collisional orogens. They formed over a large crustal-depth range from deep-seated low-salinity H2O-CO2 + CH4 + N2 ore fluids and with Au transported as thio-complexes. Regional structures provide the main control on deposit distribution. In many terranes, first-order faults or shear zones appear to have controlled regional fluid flow, with greatest ore-fluid fluxes in, and adjacent to, lower-order faults, shear zones and/or large folds. Highly competent and/or chemically reactive rocks are the most common hosts to the larger deposits. Focusing of supralithostatic ore fluids into dilatant zones appears to occur late during the evolutionary history of the host terranes, normally within D3 or D4 in a D1-D4 deformation sequence. Reactivation of suitably oriented pre-existing structures during a change in far-field stress orientation is a factor common to many deposits, and repeated reactivation may account for multiple mineralization episodes in some larger deposits. Absolute robust ages of mineralization support their late-kinematic timing, and, in general, suggest that deposits formed diachronously towards the end of the 100 to 200 m.y. long evolutionary history of hosting orogens. For example, in the Yilgarn Block, a region specifically emphasised in this study, orogenic gold deposits formed in the time interval between 40 and 90 m.y., with most about 60 to 70 m.y., after the youngest widespread basic-ultrabasic volcanism and towards the end of felsic magmatism. The late timing of orogenic gold deposits is pivotal to geologically-based exploration methodologies. This is because the present structural geometries of: (i) the deposits, (ii) the hosting goldfields, and (iii) the enclosing terranes are all essentially similar to those during gold mineralization, at least in their relative position to each other. Thus, interpretation of geological maps and

Structural evolution of the Chugach-Prince William terrane at the hinge of the orocline in Prince William Sound, and implications for ore deposits: A section in Geologic studies in Alaska by the U.S. Geological Survey, 1992

USGS Publications Warehouse

Haeussler, Peter J.; Nelson, Steven W.

1993-01-01

The Chugach-Prince William terrane is a Mesozoic through Tertiary accretionary complex that lies along coastal southern and southeastern Alaska. In Prince William Sound, the regional structural fabric bends about 90°, forming an orocline. Rocks at the hinge of the orocline consist of turbidites, conglomerate, and minor volcanic rocks and limestone. The structural geology in the hinge region defines a number of domains (each >15 km2) consisting of kilometer-scale tight folds. Adjacent domains may have up to a 90° difference in the strike of bedding and trend of fold axes. Four granite to tonalitic or gabbro plutons are dated or inferred to be about 35 Main age, and all were emplaced after regional folding. Base-metal sulfide mineral occurrences, barren quartz veins, and strikeslip late faults locally cut the plutons and generally strike north-south. The mineral occurrences often have a dendritic network of quartz veinlets adjacent to the mineralized zone and brecciated wall rock within the zone. Oroclinal bending, in the style of bending a bar, is consistent with the origin of the complicated domainal geometry of the structures. The Contact fault, thought by some workers to juxtapose two parts of the accretionary prism, truncates one of these 35-Ma plutons with strike-slip offset, but previous reverse motion cannot be ruled out. A magmatic source for the ore-forming fluids is consistent with the structural and mineralogical data. The north-south orientation of mineralized zones suggests that east-west extension occurred possibly during release of fluids from the plutons, which locally hydrofractured the wall rocks and allowed migration of ore-forming fluids along preexisting fractures.

Lead Isotope Geochemistry of Mississippi Valley-Type Pb-Zn Deposits of the Ozark Region, U.S. Midcontinent: Constraints on the Origin of Ore Metals

NASA Astrophysics Data System (ADS)

Potra, A.

2015-12-01

The Ozark region of the U.S. midcontinent is one of the world's most important provinces of MVT mineralization, hosting world-class ore deposits. The ores in the Tri-State (TS) and Northern Arkansas (NA) districts, dominated by sphalerite, are mainly hosted by platform carbonate rocks and vary in age from Ordovician and Mississippian for NA and Mississippian for TS. The deposits are considered to have formed from a regional hydrothermal flow system consisting of sedimentary brines discharged from the Arkoma basin and adjacent platform during the Late Pennsylvanian to Early Permian Ouachita orogeny. New MC-ICP-MS Pb isotope analyses of sphalerites are presented in order to compare and contrast the isotopic signature of ores from the NA and TS districts with those from other MVT districts from central and eastern US and trace metal sources. The Pb isotope ratios of ores from the TS District (208Pb/204Pb between 40.7443 and 41.2626; 207Pb/204Pb between 15.8633 and 15.9571; 206Pb/204Pb between 21.8373 and 22.1956) plot in an area that is superimposed on the Pb isotope field defined by samples from the Central Missouri District, suggesting similar metal sources. The sphalerites are less radiogenic than samples from the Upper Mississippi Valley District, but more radiogenic than samples from any other MVT district. Sphalerites from the NA District have lower Pb isotope values (208Pb/204Pb between 39.4633 and 40.8863; 207Pb/204Pb between 15.8216 and 15.9176; 206Pb/204Pb between 20.2396 and 21.6438) than the TS District ores; they plot below the field defined by samples from the Illinois-Kentucky district and overlap the field defined by ores from the Southeast Missouri (Viburnum and Old Lead Belt) district, implying similar metal sources. Current data suggest that basement of Grenvillian age (1 - 1.2 by), thought to be present in Arkansas, to the south of the Viburnum Trend, may be a likely source of the radiogenic Pb component. Pb data from ores in the NA and the

Groundwater in geologic processes, 2nd edition

USGS Publications Warehouse

Ingebritsen, Steven E.; Sanford, Ward E.; Neuzil, Christopher E.

2006-01-01

Interest in the role of Groundwater in Geologic Processes has increased steadily over the past few decades. Hydrogeologists and geologists are now actively exploring the role of groundwater and other subsurface fluids in such fundamental geologic processes as crustal heat transfer, ore deposition, hydrocarbon migration, earthquakes, tectonic deformation, diagenesis, and metamorphism.Groundwater in Geologic Processes is the first comprehensive treatment of this body of inquiry. Chapters 1 to 4 develop the basic theories of groundwater motion, hydromechanics, solute transport, and heat transport. Chapter 5 applies these theories to regional groundwater flow systems in a generic sense, and Chapters 6 to 13 focus on particular geologic processes and environments. Relative to the first edition of Groundwater in Geologic Processes , this second edition includes a much more comprehensive treatment of hydromechanics (the coupling of groundwater flow and deformation). It also includes new chapters on "compaction and diagenesis," "metamorphism," and "subsea hydrogeology." Finally, it takes advantage of the substantial body of published research that has appeared since the first edition in 1998. The systematic presentation of theory and application, and the problem sets that conclude each chapter, make this book ideal for undergraduate- and graduate-level geology courses (assuming that the students have some background in calculus and introductory chemistry). It also serves as an invaluable reference for researchers and other professionals in the field

Comparison of the Ores of Swambo and Kalongwe with Shinkolobwe; LES GITES DE SWAMBO ET DE KALONGWE COMPARES A SHINKOLOBWE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Derriks, J.J.; Oosterbosch, R.

1959-10-31

Swambo is a small uraniferous deposit discovered recently to the east of Shimkolobwe. The mineralization found is localized in the breccia and the epontes'' of a transverse fault affecting a layer of the ore series. This layer is part of an anticline alignment which can be followed from Shinkolobwe to Kalongwe and the length of which is level with the schisto-dolomitric stratum. The discovery of the ore deposit was made hy the application of radiometric methods. A prelimiary series of borings showed that the usable mineralization extends 125 m under the surface. The development by mining has gone to themore » hydrostatic level. From a genetic viewpoint, the ore deposit is similar to that of Shinkolobwe, but it is less important. Kalongwe is a cupro-cobaltic ore deposit lying to the southeast of Kolwezi. The deposit is principally localized in a fault which intersects a small layer of the ore series. The greso-dolomitic stratum at the base of this series is impregnated with powdered black uranium oxides in the neighhorhood of the fault. The mineralization extends to 80 m of depth. The ore deposit was developed by mining to a depth of 42 m. The genesis of the deposit is comparable to that of Shinkolobwe, hat the Kalongwe ores are distinguished by the relative abundance of copper and the absence of nickel. (tr- auth)« less

[NIR and XRD analysis of drill-hole samples from Zhamuaobao iron-graphite deposit, Inner Mongolia].

PubMed

Li, Ying-kui; Cao, Jian-jin; Wu, Zheng-quan; Dai, Dong-le; Lin, Zu-xu

2015-01-01

The author analyzed the 4202 drill-hole samples from Zhamuaobao iron-graphite deposit by using near infrared spectroscopy(NIR) and X-ray diffraction(XRD) measuring and testing techniques, and then compared and summarized the results of two kinds of testing technology. The results indicate that some difference of the mineral composition exists among different layers, the lithology from upper to deeper is the clay gravel layer of tertiary and quaternary, mudstone, mica quartz schist, quartz actinolite scarn, skarnization marble, iron ore deposits, graphite deposits and mica quartz schist. The petrogenesis in different depth also shows difference, which may indicate the geological characteristic to some extent. The samples had mainly undergone such processes as oxidization, carbonation, chloritization and skarn alteration. The research results can not only improve the geological feature of the mining area, but also have great importance in ore exploration, mining, mineral processing and so on. What's more, as XRD can provide preliminary information about the mineral composition, NIR can make further judgement on the existence of the minerals. The research integrated the advantages of both NIR and XRD measuring and testing techniques, put forward a method with two kinds of modern testing technology combined with each other, which may improve the accuracy of the mineral composition identification. In the meantime, the NIR will be more wildly used in geography on the basis of mineral spectroscopy.

The geology and ore deposits of Upper Mayflower Gulch, Summit County, Colorado

USGS Publications Warehouse

Randall, John Alexander

1958-01-01

Upper Mayflower Gulch is on the highly glaciated western side of the Tenmile Range near Kokomo in central Colorado. Somewhat less than $500,000 in silver and gold has been produced from the area since the first mining in the 1880' s. In the mapped area high grade regional metamorphism has produced two varieties of gneiss and a granulite. Total thickness of the rocks is about 5,000 feet. Relict bedding is preserved in compositional banding which strikes north to N. 20 ? E. and dips 70 ? to 80 ? southeast. No significant folding was observed. Normal faulting has occurred since the Precambrian; two major sets of faults are recognizable: (1) a set striking N. 70 ? to 85 ? E. and dipping 75?-85 ? NW; and (2) a set striking N. 70?-50 ? W. and dipping 50?-60 ? SW. Tabular bodies of pegmatite and retrogressively metamorphosed schist along many faults indicate Precambrian movement. The Mayflower fault, a 90 to 300 foot wide zone of siltification and shattered rock, strikes about N. 40 ? W. It extends the entire length of the gulch and appears to form the northern terminus for the northeast trending Mosquito Fault. The Mayflower fault shows repeated movement since the Precambrian, totaling about 3,000 feet of apparent dip slip and 640 feet of apparent strike slip. Faulting during the Tertiary includes both additional movement along Precambrian faults and development of shears trending N. to N. 20 ? E. The shears served as channels for the intrusion of two varieties of quartz latite porphyry dikes. Specular hematite and base-metal sulfide mineralization followed intrusion of the porphyry dikes; the minerals were deposited in open fault zones by high temperature solutions in a low pressure environment. The principal metallic minerals in order of deposition are: hematite, pyrite, chalcopyrite, sphalerite, galena, and rarer argentite. The major mines are the Gold Crest, Payrock, Nova Scotia Boy, and Bird's Nest.

Statistical sampling of the distribution of uranium deposits using geologic/geographic clusters

USGS Publications Warehouse

Finch, W.I.; Grundy, W.D.; Pierson, C.T.

1992-01-01

The concept of geologic/geographic clusters was developed particularly to study grade and tonnage models for sandstone-type uranium deposits. A cluster is a grouping of mined as well as unmined uranium occurrences within an arbitrary area about 8 km across. A cluster is a statistical sample that will reflect accurately the distribution of uranium in large regions relative to various geologic and geographic features. The example of the Colorado Plateau Uranium Province reveals that only 3 percent of the total number of clusters is in the largest tonnage-size category, greater than 10,000 short tons U3O8, and that 80 percent of the clusters are hosted by Triassic and Jurassic rocks. The distributions of grade and tonnage for clusters in the Powder River Basin show a wide variation; the grade distribution is highly variable, reflecting a difference between roll-front deposits and concretionary deposits, and the Basin contains about half the number in the greater-than-10,000 tonnage-size class as does the Colorado Plateau, even though it is much smaller. The grade and tonnage models should prove useful in finding the richest and largest uranium deposits. ?? 1992 Oxford University Press.

Regional stratigraphy and subsurface geology of Cenozoic deposits, Gulf Coastal Plain, south-central United States

USGS Publications Warehouse

Hosman, R.L.

1991-01-01

Although Cenozoic deposits are not uniformly differentiated, interstate correlations of major Paleocene and Eocene units are generally established throughout the area. Younger deposits are not as well differentiated. Some stratigraphic designations made at surface exposures cannot be extended into the sub-surface, and the scarcity of distinct geologic horizons has hampered differentiation on a regional scale. The complexities of facies development in Oligocene and younger coastal deposits preclude the development of extensive recognizable horizons needed for stratigraphic applications. Coastal deposits are a heterogeneous assemblage of deltaic, lagoonal, lacustrine, palustrine, eolian, and fluvial clastic facies and local calcareous reef facies. Even major time boundaries, as between geologic series, are not fully resolved. Surficial Quaternary deposits overlie the truncated subcrops of Tertiary strata and generally are distinguishable, although some contacts between Pleistocene and underlying Pliocene deposits have been a ?lstoncal source of controversy. Glacially related terraces are characteristic of the Pleistocene Epoch, and alluvium of aggrading streams typifies the Holocene. 

Statistical analysis of soil geochemical data to identify pathfinders associated with mineral deposits: An example from the Coles Hill uranium deposit, Virginia, USA

USGS Publications Warehouse

Levitan, Denise M.; Zipper, Carl E.; Donovan, Patricia; Schreiber, Madeline E.; Seal, Robert; Engle, Mark A.; Chermak, John A.; Bodnar, Robert J.; Johnson, Daniel K.; Aylor, Joseph G.

2015-01-01

Soil geochemical anomalies can be used to identify pathfinders in exploration for ore deposits. In this study, compositional data analysis is used with multivariate statistical methods to analyse soil geochemical data collected from the Coles Hill uranium deposit, Virginia, USA, to identify pathfinders associated with this deposit. Elemental compositions and relationships were compared between the collected Coles Hill soil and reference soil samples extracted from a regional subset of a national-scale geochemical survey. Results show that pathfinders for the Coles Hill deposit include light rare earth elements (La and Ce), which, when normalised by their Al content, are correlated with U/Al, and elevated Th/Al values, which are not correlated with U/Al, supporting decoupling of U from Th during soil generation. These results can be used in genetic and weathering models of the Coles Hill deposit, and can also be applied to future prospecting for similar U deposits in the eastern United States, and in regions with similar geological/climatic conditions.

Compilation of Mineral Resource Data for Mississippi Valley-Type and Clastic-Dominated Sediment-Hosted Lead-Zinc Deposits

USGS Publications Warehouse

Taylor, Ryan D.; Leach, David L.; Bradley, Dwight C.; Pisarevsky, Sergei A.

2009-01-01

districts, the resource data are presented in appendix table A2. In addition, numerous figures (appendix figures B1-B9) displaying important grade-tonnage and geologic features are included. These mineral deposit resource data are important for exploration targeting and mineral resource assessments. There is significant variability in the resource data for these deposit types, and ore controls vary from one region to another. Therefore, grade-tonnage estimations are best evaluated as subsets of the data in appendix table A1 where local mineralization styles and ore controls characterize the region being evaluated for grade-tonnage relations. Furthermore, consideration should also be given to the tendency for MVT resources to occur in large mineralized regions.

Carbonatites of the World, Explored Deposits of Nb and REE - Database and Grade and Tonnage Models

USGS Publications Warehouse

Berger, Vladimir I.; Singer, Donald A.; Orris, Greta J.

2009-01-01

This report is based on published tonnage and grade data on 58 Nb- and rare-earth-element (REE)-bearing carbonatite deposits that are mostly well explored and are partially mined or contain resources of these elements. The deposits represent only a part of the known 527 carbonatites around the world, but they are characterized by reliable quantitative data on ore tonnages and grades of niobium and REE. Grade and tonnage models are an important component of mineral resource assessments. Carbonatites present one of the main natural sources of niobium and rare-earth elements, the economic importance of which grows consistently. A purpose of this report is to update earlier publications. New information about known deposits, as well as data on new deposits published during the last decade, are incorporated in the present paper. The compiled database (appendix 1; linked to right) contains 60 explored Nb- and REE-bearing carbonatite deposits - resources of 55 of these deposits are taken from publications. In the present updated grade-tonnage model we have added 24 deposits comparing with the previous model of Singer (1998). Resources of most deposits are residuum ores in the upper part of carbonatite bodies. Mineral-deposit models are important in exploration planning and quantitative resource assessments for two reasons: (1) grades and tonnages among deposit types vary significantly, and (2) deposits of different types are present in distinct geologic settings that can be identified from geologic maps. Mineral-deposit models combine the diverse geoscience information on geology, mineral occurrences, geophysics, and geochemistry used in resource assessments and mineral exploration. Globally based deposit models allow recognition of important features and demonstrate how common different features are. Well-designed deposit models allow geologists to deduce possible mineral-deposit types in a given geologic environment, and the grade and tonnage models allow economists to

Metallogeny of Mesoproterozoic Sedimentary Rocks in Idaho and Montana - Studies by the Mineral Resources Program, U.S. Geological Survey, 2004-2007

USGS Publications Warehouse

O'Neill, J. Michael

2007-01-01

Preface By J.Michael O'Neill The major emphasis of this project was to extend and refine the known Mesoproterozoic geologic and metallogenic framework of the region along and adjacent to the Idaho-Montana boundary north of the Snake River Plain. The Mesoproterozoic metasedimentary rocks in this part of east-central Idaho host important Cu-Co-Au stratabound mineral resources as well as younger, epigenetic hydrothermal, sulfide base-metal mineral deposits. Two tasks of this study were to more accurately understand and portray the character and origin of cobalt-copper-gold deposits that compose the Idaho cobalt belt and specifically to analyze ore mineralogy and metallogenesis within the Blackbird mining district in the central part of the belt. Inasmuch as the cobalt belt is confined to the Mesoproterozoic Lemhi Group strata of east-central Idaho, geologic investigations were also undertaken to determine the relationship between strata of the Lemhi Group and the more extensive, noncobalt-bearing, Belt-Purcell Supergroup strata to the north and northwest. Abrupt lateral differences in the character and thickness of stratigraphic units in the Mesoproterozoic Lemhi Basin may indicate differential sedimentation in contemporaneous fault-bounded subbasins. It is suggested that northeast-trending basement faults of the Great Falls tectonic zone controlled development of the subbasins. O'Neill and others (chapter A, this volume) document a second major basement fault in this area, the newly recognized northwest-striking Great Divide megashear, a zone 1-2 km wide of left-lateral strike-slip faults active during Mesoproterozoic sedimentation and bounding the Cu-Co belt on the northwest. The megashear is a crustal-scale tectonic feature that separates Lemhi Group strata from roughly coeval Belt-Purcell strata to the north and northwest in Montana and northern Idaho. The results of numerous geologic investigations of the Cu- and Co-bearing Mesoproterozoic rocks of east

Effects of simulated deposition of acid mist and iron ore particulate matter on photosynthesis and the generation of oxidative stress in Schinus terebinthifolius Radii and Sophora tomentosa L.

PubMed

Kuki, Kacilda Naomi; Oliva, Marco Antônio; Pereira, Eduardo Gusmão; Costa, Alan Carlos; Cambraia, José

2008-09-15

Particulate matter is a natural occurrence in the environment, but some industries, such as the iron ore sector, can raise the total amount of particles in the atmosphere. This industry is primarily a source of iron and sulfur dioxide particulates. The effects of the pollutants from the iron ore industries on representatives of restinga vegetation in a Brazilian coastal ecosystem were investigated using physiological and biochemical measures. Two species, Schinus terebinthifolius and Sophora tomentosa, were exposed to simulated deposition of acid mist and iron ore particulate matter in acrylic chambers in a greenhouse. Parameters such as gas exchange, fluorescence emission, chlorophyll content, total iron content, antioxidant enzyme activity and malondialdehyde content were assessed in order to evaluate the responses of the two species. Neither treatment was capable of inducing oxidative stress in S. terebinthifolius. Nevertheless, the deposition of iron ore particulates on this species increased chlorophyll content, the maximum quantum efficiency of photosystem II and the electron transport rate, while iron content was unaltered. On the other hand, S. tomentosa showed a greater sensitivity to the treatments. Plants of S. tomentosa that were exposed to acid mist had a decrease in photosynthesis, while the deposition of iron particulate matter led to an increase in iron content and membrane permeability of the leaves. The activities of antioxidant enzymes, such as catalases and superoxide dismutase, were enhanced by both treatments. The results suggested that the two restinga species use different strategies to overcome the stressful conditions created by the deposition of particulate matter, either solid or wet. It seems that while S. terebinthifolius avoided stress, S. tomentosa used antioxidant enzyme systems to partially neutralize oxidative stress. The findings also point to the potential use of S. tomentosa as a biomarker species under field conditions.

Evidence for microbial activity in the formation of carbonate-hosted Zn-Pb deposits

NASA Astrophysics Data System (ADS)

Kucha, H.; Raith, J.

2009-04-01

*Kucha H **Raith J *University of Mining and Metallurgy, Faculty of Geology, Geophysics and Environmental Protection, Mickiewicza 30, PL-30-059 Krakow, Poland. ** University of Leoben, Department of Applied Geosciences and Geophysics, A-8700 Leoben, Peter Tunner Str. 5, Austria Evidence for microbial activity in the formation of carbonate-hosted Zn-Pb deposits To date evaluation of bacterial processes in the formation of carbonate-hosted Zn-Pb deposits is largely based on sulphur isotope evidence. However, during a past few years, textural criteria, have been established, which support the bacterial origin of many of these deposits. This has received a strong support from micro-, and nano-textures of naturally growing bacterial films in a flooded tunnel within carbonates that host the Piquette Zn-Pb deposit (Druschel et al., 2002). Bacterial textures, micro- and nano textures found in carbonate-hosted Zn-Pb deposits are: i)wavy bacterial films up to a few mm thick to up to a few cm long composed of peloids, ii)semimassive agglomeration of peloids in the carbonate matrix, and iii)solitary peloids dispersed in the carbonate matrix. Peloids are usually composed of a distinct 50-90um core most often made up of Zn-bearing calcite surrounded by 30-60um thick dentate rim composed of ZnS. Etching of Zn-carbonate cores reveals 1 - 2um ZnS filaments, and numerous 15 to 90nm large ZnS nano-spheres (Kucha et al., 2005). In massive ore composite Zn-calcite - sphalerite peloids are entirely replaced by zinc sulphide, and form peloids ghosts within banded sulphide layers. Bacterially derived micro- and nano-textures have been observed in the following carbonate-hosted Zn-Pb deposits: 1)Irish-type Zn-Pb deposits. In the Navan deposit the basic sulphur is isotopically light bacteriogenic S (Fallick at al., 2001). This is corroborated by semimassive agglomerations of composite peloids (Zn-calcite-ZnS corona or ZnS core-melnikovite corona). Etching of Zn-calcite core reveals globular

Early Jurassic mafic dykes from the Aigao uranium ore deposit in South China: Geochronology, petrogenesis and relationship with uranium mineralization

NASA Astrophysics Data System (ADS)

Zhang, Di; Zhao, Kui-Dong; Chen, Wei; Jiang, Shao-Yong

2018-05-01

Mafic dykes are abundant and widely distributed in many granite-hosted uranium ore deposits in South China. However, their geochronology, petrogenesis and relationship with uranium mineralization were poorly constrained. In this study, apatite U-Pb dating, whole-rock major and trace element and Sr-Nd-Pb isotope analysis were conducted for the dolerite dykes from the Aigao uranium ore deposit. Apatite U-Pb isotopic data indicate that the mafic dykes were emplaced at Early Jurassic (189 ± 4 Ma), which provides new evidence for the rarely identified Early Jurassic magmatism in South China. Pyroxene from the dykes is mainly augite, and plagioclase belongs to albite. The dolerite samples have relatively low SiO2 contents (45.33-46.79 wt%), relatively high total alkali contents (K2O + Na2O = 4.11-4.58 wt%) and Al2O3 contents (13.39-13.80 wt%), and medium MgO contents (4.29-5.16 wt%). They are enriched in Nb, Ta, Ti, rare earth elements and depleted in Rb, K, Sr, Th, showing the typical OIB-like geochemical affinity. All the dolerite samples show homogeneous Sr-Nd-Pb isotopic compositions, with (87Sr/86Sr)i varying from 0.706049 to 0.707137, εNd(t) from +4.6 to +5.2, 206Pb/204Pb from 19.032 to 19.126 and 207Pb/204Pb from 15.641 to 15.653. The mafic dykes in the Aigao deposit should be derived from the partial melting of the asthenospheric mantle and formed in a within-plate extensional environment. The emplacement age of the mafic dykes is older than the uranium mineralization age. Therefore, CO2 in ore-forming fluids couldn't originate from the basaltic magma as suggested by previous studies. The dolerite dykes might only provide a favorable reducing environment to promote the precipitation of uraninite from oxidize hydrothermal fluids.

Composition and origin of Early Cambrian Tiantaishan phosphorite-Mn carbonate ores, Shaanxi Province, China

USGS Publications Warehouse

Hein, J.R.; Fan, D.; Ye, J.; Liu, T.; Yeh, H.-W.

1999-01-01

The Tiantaishan phosphorite-Mn carbonate ores occur in the Early Cambrian Tananpo Formation in complexly folded and faulted rocks located in southern Shaanxi Province. About 65 x 106 tonnes of 17% P2O5 ore reserves exist and Mn-ore reserves are about 8.3 x 106 tonnes of +18% Mn. The stratigraphic sequence in ascending order consists of black phyllite, black to gray phosphorite ore, black phyllite, rhodochrostone ore, Mn mixed-carbonates, and dolostone. Data are presented from microprobe mineral chemistry, whole-rock chemistry, stable isotopes of carbonates, X-ray mineralogy, petrographic and SEM observations, and statistical analysis of chemical data. The dominant ore-forming minerals are hydroxy- and carbonate fluorapatite and Ca rhodochrosite, with Mg kutnahorite and dolomite comprising the Mn mixed-carbonate section. Pyrite occurs in all rock types and alabandite (MnS) occurs throughout the rhodochrostone section. The mean P2O5 content of phosphorite is 31% and argillaceous phosphorite is 16%, while the mean MnO content of rhodochrostone ore is 37%. Phosphorite ores are massive, spheroidal, laminated, and banded, while rhodochrostone ores have oolitic, spheroidal, and granular fabrics. The most distinguishing characteristics of the ores are high total organic carbon (TOC) contents (mean 8.4%) in the phosphorite and high P2O5 contents (mean 2.7%) in the rhodochrostone ore. The atypically high TOC contents in the Tiantaishan phosphorite probably result from very strong productivity leading to high sedimentation rates accompanied by weak reworking of sediments; poor utilization of the organic matter by bacteria; and/or partial replacement of bacterial or algal mats by the apatite. The depositional setting of the ores was the margin of an epicontinental seaway created as a direct consequence of global processes that included break-up of a supercontinent, formation of narrow seaways, creation of extensive continental shelves, overturn of stagnant, metal-rich deep

Some limitations on the possible composition of the ore-forming fluid

USGS Publications Warehouse

Barton, Paul B.

1956-01-01

The activity rations of various important anions (S, CO3, SO4, OH, F, and Cl) in hydrothermal solutions at the time of deposition are evaluated using a simple thermodynamic technique. The rations are interpreted in the light of the mineralogy of ore deposits and limites are placed on the variability of each ratio in hydrothermal solutions. All of the calculations are made for 25°C and cautious extrapolation to higher temperatures seems justified; however, additional data for elevated temperatures and pressures are needed before more than approximate values may be assigned to these ratios in the ore-forming fluid. The calculated partial pressure of CO2 in the ore fluid is generally less than one atmosphere, which suggests that a dense CO2 phase cannot be considered an importatn ore fluid for most deposits. The partial pressure of H2S is usually less than 10-4 atmospheres which makes it extremely difficult to defend the heory that metals (other than the easily complexible mercury, arsenic, antimony, and perhaps fols and silver) are transported in quantity as complex sulfide and hydrosulfides. The sulfate to sulfide ration is such that the oxidation potential at the time of deposition is defined by the following equation: Eh (in volts) = 0.22 ± 0.04 - 0.059 pH.

Characteristics of some silver-, and base metal-bearing, epithermal deposits of Mexico and Peru

USGS Publications Warehouse

Foley, Nora K.

1984-01-01

Although many characteristics of the geology and geochemistry of this type of deposit were considered, the most important criterion for choosing these deposits was that they have substantial quantities of precious- and base-metal mineralization. Additional criteria for selecting the deposits were that they be hosted primarily by calc-alkaline volcanic rocks of intermediate to silicic composition and that they be younger than Tertiary in age. Many deposits in Mexico and Peru and other parts of Central and South America were excluded because the literature describing the districts is not readily available. Furthermore, many districts have not been examined in detail or the information available is of limited geological scope. The four districts that are compiled in this report were chosen because they are described in abundant literature dating from early mining reports on the general geology and mineralogy to very recent data on detailed geochemical and mineralogical studies. They were chosen as being fairly typical, classic examples of near-surface, low-temperature vein deposits as described by Lindgren (1928) in his treatise on ore deposits (Mineral deposits, McGraw-Hill, 1049 p.). These deposits are similar in aspects of their geology and geochemistry to many of the famous, epithermal silver mining districts in Colorado and Nevada including Creede, Colorado, Tonapah, Nevada, and the Sunnyside Mine of the Eureka district, Colorado, and, in the special case of Julcani, to Summitville, Colorado, and Goldfield, Nevada. The characteristics that distinguish them include overall size, production and alteration assemblage. The information documented in each summary will be used in a forthcoming series of papers on the comparative anatomy of precious and base metal deposits in North and South America.

ASTER, ALI and Hyperion sensors data for lithological mapping and ore minerals exploration.

PubMed

Beiranvand Pour, Amin; Hashim, Mazlan

2014-01-01

This paper provides a review of the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER), Advanced Land Imager (ALI), and Hyperion data and applications of the data as a tool for ore minerals exploration, lithological and structural mapping. Spectral information extraction from ASTER, ALI, and Hyperion data has great ability to assist geologists in all disciplines to map the distribution and detect the rock units exposed at the earth's surface. The near coincidence of Earth Observing System (EOS)/Terra and Earth Observing One (EO-1) platforms allows acquiring ASTER, ALI, and Hyperion imagery of the same ground areas, resulting accurate information for geological mapping applications especially in the reconnaissance stages of hydrothermal copper and gold exploration, chromite, magnetite, massive sulfide and uranium ore deposits, mineral components of soils and structural interpretation at both regional and district scales. Shortwave length infrared and thermal infrared bands of ASTER have sufficient spectral resolution to map fundamental absorptions of hydroxyl mineral groups and silica and carbonate minerals for regional mapping purposes. Ferric-iron bearing minerals can be discriminated using six unique wavelength bands of ALI spanning the visible and near infrared. Hyperion visible and near infrared bands (0.4 to 1.0 μm) and shortwave infrared bands (0.9 to 2.5 μm) allowed to produce image maps of iron oxide minerals, hydroxyl-bearing minerals, sulfates and carbonates in association with hydrothermal alteration assemblages, respectively. The techniques and achievements reviewed in the present paper can further introduce the efficacy of ASTER, ALI, and Hyperion data for future mineral and lithological mapping and exploration of the porphyry copper, epithermal gold, chromite, magnetite, massive sulfide and uranium ore deposits especially in arid and semi-arid territory.

Distribution of radioactive isotopes in rock and ore of Arkhangelskaya pipe from the Arkhangelsk diamond province

NASA Astrophysics Data System (ADS)

Kiselev, G. P.; Yakovlev, E. Yu.; Druzhinin, S. V.; Galkin, A. S.

2017-09-01

The contents of radioactive elements and the uranium isotopic composition of kimberlite in the Arkhangelskaya pipe at the M.V. Lomonosov deposit and of nearby country rocks have been studied. A surplus of 234U isotope has been established in rocks from the near-pipe space. The high γ = 234U/238U ratio is controlled by the geological structure of the near-pipe space. A nonequilibrium uranium halo reaches two pipe diameters in size and can be regarded as a local ore guide for kimberlite discovery. The rocks in the nearpipe space are also characterized by elevated or anomalous U, Th, and K contents with respect to the background.

Geological and geochemical aspects of uranium deposits: a selected, annotated bibliography. [474 references

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas, J.M.; Garland, P.A.; White, M.B.

This bibliography, a compilation of 474 references, is the fourth in a series compiled from the National Uranium Resource Evaluation (NURE) Bibliographic Data Base. This data base was created for the Grand Junction Office of the Department of Energy's National Uranium Resource Evaluation Project by the Ecological Sciences Information Center, Oak Ridge National Laboratory. The references in the bibliography are arranged by subject category: (1) geochemistry, (2) exploration, (3) mineralogy, (4) genesis of deposits, (5) geology of deposits, (6) uranium industry, (7) geology of potential uranium-bearing areas, and (8) reserves and resources. The references are indexed by author, geographic location,more » quadrangle name, geoformational feature, and keyword.« less

Silicophosphate Sorbents, Based on Ore-Processing Plants' Waste in Kazakhstan

ERIC Educational Resources Information Center

Kubekova, Sholpan N.; Kapralova, Viktoria I.; Telkov, Shamil A.

2016-01-01

The problem of ore-processing plants' waste and man-made mineral formations (MMF) disposal is very important for the Republic of Kazakhstan. The research of various ore types (gold, polymetallic, iron-bearing) MMF from a number of Kazakhstan's deposits using a complex physical and chemical methods showed, that the waste's main components are…

Evidence for a Hematite Ore Body on Mars

NASA Technical Reports Server (NTRS)

Morris, Richard V.; Lane, M. D.; Christensen, P. R.

2000-01-01

The Mars Global Surveyor (MGS) spacecraft was launched from Cape Kennedy in November 1996. MGS was put into orbit around Mars in September of 1997 and has since been sending back data from a suite of instruments, including the Thermal Emission Spectrometer (TES). The TES instrument is an interferometric spectrometer designed to map the surface mineralogy of Mars by measuring the midinfrared emitted radiation over the spectral region of about 1600 to 200 cm(exp -1) (about 6 to 50 microns). This mineralogically sensitive technique utilizes the characteristic intra- and inter-molecular vibrations of minerals that are manifested in the midinfrared spectra. These spectral "fingerprints" are unique because they are dependent upon chemical composition, crystal structure, crystal orientation, and other factors. Midinfrared spectral data received from the MGS-TES instrument have indicated the presence of a large deposit of hematite (alpha-Fe2O3) in Sinus Meridiani, Mars. This hematite ore body, that is accompanied by basalt, is really extensive, encompassing an area about 350 by 500 km. To better understand the geologic context of this large deposit, a detailed laboratory spectroscopic investigation was conducted using more than 20 hematite samples so that their spectra could be compared to the martian spectra. The samples included red and gray polycrystaline hand samples, gray single-crystal hand samples, and red and gray fine- and coarse-grained particulates. The laboratory analyses provided thermal emissivity spectra that, when compared to the hematite emissivity spectra from Mars, suggest the Sinus Meridiani hematite is possibly an exposure of oriented hematite grains. These grains are likely coarser that 10 microns (and may be much larger) and gray in color. The characteristic of oriented grains is suggested by the apparent crystal axis-dependence of the energy emitted from the surface of Mars. The strong degree of crystal alignment exhibited in the emissivity spectra

Evidence for a Hematite Ore Body on Mars

NASA Technical Reports Server (NTRS)

Lane, M. D.; Christensen, P. R.

2000-01-01

The Mars Global Surveyor (MGS) spacecraft was launched from Cape Kennedy in November 1996. MGS was put into orbit around Mars in September of 1997 and has since been sending back data from a suite of instruments, including the Thermal Emission Spectrometer (TES). The TES instrument is an interferometric spectrometer designed to map the surface mineralogy of Mars by measuring the midinfrared emitted radiation over the spectral region of approximately 1600 to 200 per centimeter (appjroximately 6 to 50 microns). This mineralogically sensitive technique utilizes the characteristic intra- and inter-molecular vibrations of minerals that are manifested in the midinfrared spectra. These spectral "fingerprints" are unique because they are dependent upon chemical composition, crystal structure, crystal orientation, and other factors. Midinfrared spectral data received from the MGS-TES instrument have indicated the presence of a large deposit of hematite (alpha-Fe2O3) in Sinus Meridiani, Mars. This hematite ore body, that is accompanied by basalt, is areally extensive, encompassing and area approximately 350 by 500 km. To better understand the geologic context of this large deposit, a detailed laboratory spectroscopic investigation was conducted using more than 20 hematite samples so that their spectra could be compared to the martian spectra. The samples included red and gray polycrystaline hand samples, gray single-crystal hand samples, and red and gray fine- and coarse-grained particulates. The laboratory analyses provided thermal emissivity spectra that, when compared to the hematite emissivity spectra from Mars, suggest the Sinus Meridiani hematite is possibly an exposure of oriented hematite grains. These grains are likely coarser that 10 microns (and may be much larger) and gray in color The characteristic of oriented grains is suggested by the apparent crystal axis-dependence of the energy emitted from the surface of Mars. The strong degree of crystal alignment

The volcanic-sedimentary sequence of the Lousal deposit, Iberian Pyrite Belt (Portugal)

NASA Astrophysics Data System (ADS)

Rosa, Carlos; Rosa, Diogo; Matos, Joao; Relvas, Jorge

2010-05-01

dominant fragmentation mechanism. Unlike many locations of the IPB, fiamme-rich pyroclastic units were not identified at Lousal. The ore deposits occur in close proximity with this volcanic centre that may have driven hydrothermal circulation that led to ore formation. The volcanic rocks show intense chloritic alteration, indicating that the mineralizing event occurred after most of the rhyolitic units have emplaced. The massive sulfides show abundant sedimentary structures which is not typical in the massive sulfide deposits of the IPB. The Lousal 50 Mt massive sulfide deposit consists of at least 11 ore bodies and was exploited until 1988 mainly for pyrite. The ores mined averaged 0.7% Cu, 0.8%Pb e 1.4%Zn (Strauss, 1971). These relatively low base metal grades led to an evaluation of the contents and distribution of high-tech element in the ore bodies, which would improve the economic viability of mining the deposit. This evaluation is currently focusing on the distribution and mineralogy of selenium, as ores mined in the past were known to be rich in this element. This work benefits from research projects INCA (PTDC/CTE-GIN/67027/2006; Characterization of crucial mineral resources for the development of renewable energy technologies: The Iberian Pyrite Belt ores as a source of indium and other high-technology elements) and project ARCHYMEDES II (POCTI/CTA/45873/2002), both funded by the Fundação para a Ciência e Tecnologia. REFERENCES Strauss, G.K., 1970. Sobre la geologia de la provincia piritifera del Suroeste de la Peninsula Iberica y sus yacimientos, en especial sobre la mina de pirita de Lousal (Portugal): Memoria del IGME 77, 1-266. Tornos, F., 2006. Environment of formation and styles of volcanogenic massive sulfides: The Iberian Pyrite Belt. Ore Geology Reviews 28, 259-307.

Geologic, hydrologic, and geochemical interpretations of mineral deposits as analogs for understanding transport of environmental contaminants

USGS Publications Warehouse

Wanty, R.B.; Berger, B.R.

2006-01-01

Base- and precious-metal mineral deposits comprise anomalous concentrations of metals and associated elements, which may be useful subjects for study as analogs for migration of environmental contaminants. In the geologic past, hydrothermal mineral deposits formed at the intersection of favorable geologic, hydrologic and geochemical gradients. In the present, weathering of these sulfide-rich deposits occurs as a result of the interplay between rates of oxygen supply versus rates of ground or surface-water flow. Transport and spatial dispersion of elements from a mineral deposit occurs as a function of competing rates of water flow versus rates of attenuation mechanisms such as adsorption, dilution, or (co)precipitation. In this paper we present several case studies from mineralized and altered sedimentary and crystalline aquifers in the western United States to illustrate the geologic control of ground-water flow and solute transport, and to demonstrate how this combined approach leads to a more complete understanding of the systems under study as well as facilitating some capability to predict major flow directions in aquifers.

Occurrence model for volcanogenic beryllium deposits: Chapter F in Mineral deposit models for resource assessment

USGS Publications Warehouse

Foley, Nora K.; Hofstra, Albert H.; Lindsey, David A.; Seal, Robert R.; Jaskula, Brian W.; Piatak, Nadine M.

2012-01-01

Current global and domestic mineral resources of beryllium (Be) for industrial uses are dominated by ores produced from deposits of the volcanogenic Be type. Beryllium deposits of this type can form where hydrothermal fluids interact with fluorine and lithophile-element (uranium, thorium, rubidium, lithium, beryllium, cesium, tantalum, rare earth elements, and tin) enriched volcanic rocks that contain a highly reactive lithic component, such as carbonate clasts. Volcanic and hypabyssal high-silica biotite-bearing topaz rhyolite constitutes the most well-recognized igneous suite associated with such Be deposits. The exemplar setting is an extensional tectonic environment, such as that characterized by the Basin and Range Province, where younger topaz-bearing igneous rock sequences overlie older dolomite, quartzite, shale, and limestone sequences. Mined deposits and related mineralized rocks at Spor Mountain, Utah, make up a unique economic deposit of volcanogenic Be having extensive production and proven and probable reserves. Proven reserves in Utah, as reported by the U.S. Geological Survey National Mineral Information Center, total about 15,900 tons of Be that are present in the mineral bertrandite (Be4Si2O7(OH)2). At the type locality for volcanogenic Be, Spor Mountain, the tuffaceous breccias and stratified tuffs that host the Be ore formed as a result of explosive volcanism that brought carbonate and other lithic fragments to the surface through vent structures that cut the underlying dolomitic Paleozoic sedimentary rock sequences. The tuffaceous sediments and lithic clasts are thought to make up phreatomagmatic base surge deposits. Hydrothermal fluids leached Be from volcanic glass in the tuff and redeposited the Be as bertrandite upon reaction of the hydrothermal fluid with carbonate clasts in lithic-rich sections of tuff. The localization of the deposits in tuff above fluorite-mineralized faults in carbonate rocks, together with isotopic evidence for the

Hydrothermal alteration, ore fluid characteristics, and gold depositional processes along a trondhjemite-komatiite contact at Tarmoola, Western Australia

USGS Publications Warehouse

Duuring, P.; Hagemann, S.G.; Cassidy, K.F.; Johnson, C.A.

2004-01-01

Tarmoola is a structurally controlled Archean orogenic gold deposit hosted in greenschist facies metamorphosed komatiite and trondhjemite in the Leonora district of the Eastern Goldfields province, Yilgarn craton. High-grade (>1 g/t Au) orebodies are located in komatiite wall rock adjacent to the eastern and northeastern margins of the asymmetrical, north-south-striking, Tarmoola trondhjemite intrusion. Gold-bearing veins post-date trondhjemite emplacement (ca. 2700 Ma), quartz diorite dikes (ca. 2667 Ma), and regional greenschist facies metamorphism. Textures and crosscutting relationships in gold-bearing veins indicate two stages of hydrothermal fluid infiltration associated with a single gold-related hydrothermal event: a volumetrically dominant, but gold-poor, stage I fluid and a gold-rich stage II fluid. Gold-bearing veins contain stage I milky quartz and pyrite that are overprinted by stage II quartz-ankerite-muscovite-chalcopyrite-sphalerite-galena-gold-tellurides ?? albite ?? chlorite ?? fuchsite ?? epidote ?? scheelite. Stage I hydrothermal alteration assemblages are different in trondhjemite and komatiite due to contrasting reactions between a common ore fluid and disparate wall-rock chemistry. Stage II fluid-wall rock interaction was minor compared to stage I and is indicated by the overprinting of stage I mineral assemblages by stage II microveins. Wall-rock alteration proximal to veins in trondhjemite is characterized by replacement of igneous plagioclase, amphibole, biotite, and metamorphic chlorite by hydrothermal quartz, muscovite, ankerite, calcite, pyrite, chalcopyrite, sphalerite, galena, tellurides, and gold, whereas in proximal alteration in komatiite, metamorphic chlorite and talc are replaced by ankerite, quartz, muscovite, albite, chlorite, fuchsite, pyrite, chalcopyrite, sphalerite, galena, tellurides, and gold. The stage II fluid was enriched in H2O, CO2, Si, Ca, K, Na, S, Au, Ag, Cu, Pb, W, Bi, As, Mo, Zn, and Te. Based on fluid inclusion

Study of iron deposit using seismic refraction and resistivity in Carajás Mineral Province, Brazil

NASA Astrophysics Data System (ADS)

Nogueira, Pedro Vencovsky; Rocha, Marcelo Peres; Borges, Welitom Rodrigues; Silva, Adalene Moreira; Assis, Luciano Mozer de

2016-10-01

This work comprises the acquisition, processing and interpretation of 2D seismic shallow refraction (P-wave) and resistivity profiles located in the iron ore deposit of N4WS, Carajás Mineral Province (CMP), northern Brazil. The geophysical methods were used to identify the boundaries of the iron ore deposit. Another objective was to evaluate the potentiality of these geophysical methods in that geological context. In order to validate the results, the geophysical lines were located to match a geological borehole line. For the seismic refraction, we used 120 channels, spaced by 10 m, in a line of 1190 m, with seven shot points. The resistivity method used in the acquisition was the electrical resistivity imaging, with pole-pole array, in order to reach greater depths. The resistivity line had a length of 1430 m, with 10 m spacing between electrodes. The seismic results produced a model with two distinct layers. Based on the velocities values, the first layer was interpreted as altered rocks, and the second layer as more preserved rocks. It was not possible to discriminate different lithologies with the seismic method inside each layer. From the resistivity results, a zone of higher resistivity (> 3937 Ω·m) was interpreted as iron ore, and a region of intermediate resistivity (from 816 to 2330 Ω·m) as altered rocks. These two regions represent the first seismic layer. On the second seismic layer, an area with intermediated resistivity values (from 483 to 2330 Ω·m) was interpreted as mafic rocks, and the area with lower resistivity (< 483 Ω·m) as jaspilite. Our results were compared with geological boreholes and show reasonable correlation, suggesting that the geophysical anomalies correspond to the main variations in composition and physical properties of rocks.

Chemistry of Selected Core Samples, Concentrate, Tailings, and Tailings Pond Waters: Pea Ridge Iron (-Lanthanide-Gold) Deposit, Washington County, Missouri

USGS Publications Warehouse

Grauch, Richard I.; Verplanck, Philip L.; Seeger, Cheryl M.; Budahn, James R.; Van Gosen, Bradley S.

2010-01-01

The Minerals at Risk and for Emerging Technologies Project of the U.S. Geological Survey (USGS) Mineral Resources Program is examining potential sources of lanthanide elements (rare earth elements) as part of its objective to provide up-to-date geologic information regarding mineral commodities likely to have increased demand in the near term. As part of the examination effort, a short visit was made to the Pea Ridge iron (-lanthanide-gold) deposit, Washington County, Missouri in October 2008. The deposit, currently owned by Wings Enterprises, Inc. of St. Louis, Missouri (Wings), contains concentrations of lanthanides that may be economic as a primary product or as a byproduct of iron ore production. This report tabulates the results of chemical analyses of the Pea Ridge samples and compares rare earth elements contents for world class lanthanide deposits with those of the Pea Ridge deposit. The data presented for the Pea Ridge deposit are preliminary and include some company data that have not been verified by the USGS or by the Missouri Department of Natural Resources, Division of Geology and Land Survey (DGLS), Geological Survey Program (MGS). The inclusion of company data is for comparative purposes only and does not imply an endorsement by either the USGS or MGS.

Sulfide minerals as new Sm-Nd geochronometers for ore genesis dating of mafic-ultramafic layered intrusions

NASA Astrophysics Data System (ADS)

Serov, Pavel; Ekimova, Nadezhda; Bayanova, Tamara

2014-05-01

The main method of dating the ore process was the Re-Os method of sulfides (Luck, Allegre, 1983; Walker et. al., 1991). However, studies of Re-Os systematics of sulfide minerals do not always give the correct ages and showing the disturbances of the Re-Os systematics. At the same time, Sm-Nd age of sulfides in good agreement with the U-Pb dating on zircon and baddeleyite and suggests that the Sm-Nd system of sulfides is more resistant to secondary alteration processes. Our studies have shown that along with rock-forming, ore minerals (sulfides) can be used to determine the ore genesis time of industrially important geological sites, since exactly with the sulfides the industry Pt-Pd mineralization is closely connected. The Sm-Nd investigations steadily employ new minerals-geochronometers. Of these, sulfides of PGE-bearing layered intrusions are quite important in terms of dating the process of ore origin. Studying the REE distribution in the sulfides of MOR hydrothermal sources has shown possible REE presence in the sulfide lattice (Rimskaya-Korsakova et. al., 2003). These are difficult to carry out because the concentrations of Sm and Nd isotopes in sulfides are much lower than chondrites (Rimskaya-Korsakova et. al., 2003). For the first time in Russia with sulfide and rock-forming minerals and WR in Sm-Nd method have been dated impregnated and brecciform ores of the following objects: Pilguyarvi Cu-Ni deposits, Pechenga (1965±87 Ma); impregnated (2433±83 Ma) and redeposited (1903±24 Ma) ores of Ahmavaara intrusion (Finland); ore gabbronorites of Penikat PGE-bearing layered intrusion (2426±38 Ma (Ekimova et.al., 2011); Pt-Pd gabbro-pegmatite ores (2476± 41 Ma, which agrees with the U-Pb zircon age - 2470±9 Ma (Bayanova, 2004) and gabbronorites (2483±86 Ma) of PGE Kievei deposit and Fedorova Tundra metagabbroids (2494±54 Ma); Monchetundra gabbronorites - 2489±49 Ma. In (Kong et. al., 2000) sulfides from two metamorphosed chondrites studied by instrumental

Structural evolution of the Mount Wall region in the Hamersley province, Western Australia and its control on hydrothermal alteration and formation of high-grade iron deposits

NASA Astrophysics Data System (ADS)

Dalstra, Hilke J.

2014-10-01

The discovery of two relatively small but high-grade iron ore deposits near Mt Wall, an intensely faulted part of the southwestern Hamersley province provides unique insights into the structural control on ore formation in this region. The deposits have many geological features typical of the high grade microplaty hematite group which also contains the much larger Mt Tom Price, Paraburdoo and Mt Whaleback deposits. The deposits are structurally controlled along early normal faults and contain abundant microplaty hematite and martite, and are largely confined to the Dales Gorge member of the Brockman Iron Formation. In addition to the microplaty hematite-martite ore, there are martite-goethite ores and rare magnetite-goethite or magnetite-hematite ores. Below the modern weathering surface, hydrothermally altered zones in wallrock BIF from the Lower Dales Gorge member contain magnetite, hematite and carbonate/talc bearing mineral assemblages. A staged ore genesis model involving early extension and fluid circulation along normal faults, hypogene silica leaching and carbonate alteration, followed by deep meteoric oxidation with microplaty hematite formation and finally weathering can explain most features of the Mt Wall deposits. The role of deformation was to provide pathways for mineralising fluids and initiate the seed points for the mineralised systems. High grade iron in the Wellthandalthaluna deposit is situated between the NW to NNW trending Boolgeeda Creek fault and a synthetic joining splay, the Northern fault. Both are high angle normal faults and formed during early extension in this part of the province. Faults are characterised by localised small scale deformation and brecciation, deep carbonate alteration and oxidation. Recent weathering has penetrated deeply into the fault zones, converting the carbonate-rich assemblages into goethite. Mineralisation in the Arochar deposit is situated in the overlap or relay zone between two segments of the Mt Wall

Nature of parent rocks, mineralization styles and ore genesis of regolith-hosted REE deposits in South China: An integrated genetic model

NASA Astrophysics Data System (ADS)

Li, Yan Hei Martin; Zhao, Wen Winston; Zhou, Mei-Fu

2017-10-01

Regolith-hosted rare earth element (REE) deposits, also called ion-adsorption or weathered crust elution-deposited REE deposits are distributed over Jiangxi, Guangdong, Fujian, Hunan, Guangxi and Yunnan provinces in South China. In general, these deposits can be categorized into the HREE-dominated type, for example the famous Zudong deposit in southern Jiangxi province and the LREE-dominated type, such as the Heling and Dingnan deposits in southern Jiangxi province. Most of these deposits form from weathering of biotite and muscovite granites, syenites, monzogranites, granodiorites, granite porphyries, and rhyolitic tuffs. The parent rocks are generally peraluminous, siliceous, alkaline and contain a variety of REE-bearing minerals. Mostly, REE patterns of regolith are inherited from the parent rocks, and therefore, characteristics of the parent rocks impose a significant control on the ore formation. Data compilation shows that autometasomatism during the latest stage of granite crystallization is likely essential in forming the HREE-enriched granites, whereas LREE-enriched granites could form through magmatic differentiation. These deposits are normally two- to three-fold, but could be up to ten-fold enrichment in REE compared to the parent granites, where the maximum enrichment usually occurs from the lower B to the upper C horizon. Ce shows different behavior with the other REEs. Strongly positive Ce anomalies commonly occur at the upper part of weathering profiles, likely due to oxidation of Ce3+ to Ce4+ and removal of Ce from soil solutions through precipitation of cerianite. Vertical pH and redox gradients in weathering crusts facilitate dissolution of REE-bearing minerals at shallow level and fixation of REE at depth through either adsorption on clay minerals or precipitation of secondary minerals. At the same time, mass removal of major elements plays an important role in concentrating REE in regolith. Combination of mass removal and eluviation

A New Occurrence Model for National Assessment of Undiscovered Volcanogenic Massive Sulfide Deposits

USGS Publications Warehouse

Shanks, W.C. Pat; Dusel-Bacon, Cynthia; Koski, Randolph; Morgan, Lisa A.; Mosier, Dan; Piatak, Nadine M.; Ridley, Ian; Seal, Robert R.; Schulz, Klaus J.; Slack, John F.; Thurston, Roland

2009-01-01

Volcanogenic massive sulfide (VMS) deposits are very significant current and historical resources of Cu-Pb-Zn-Au-Ag, are active exploration targets in several areas of the United States and potentially have significant environmental effects. This new USGS VMS deposit model provides a comprehensive review of deposit occurrence and ore genesis, and fully integrates recent advances in the understanding of active seafloor VMS-forming environments, and integrates consideration of geoenvironmental consequences of mining VMS deposits. Because VMS deposits exhibit a broad range of geological and geochemical characteristics, a suitable classification system is required to incorporate these variations into the mineral deposit model. We classify VMS deposits based on compositional variations in volcanic and sedimentary host rocks. The advantage of the classification method is that it provides a closer linkage between tectonic setting and lithostratigraphic assemblages, and an increased predictive capability during field-based studies.

Genesis of the Datuanshan stratabound skarn Cu(-Mo) deposit, Middle-Lower Yangtze Valley, Eastern China: constraints from geology, Re-Os geochronology, mineralogy, and sulfur isotopes

NASA Astrophysics Data System (ADS)

Cao, Yi; Gao, Fuping; Du, Yangsong; Du, Yilun; Pang, Zhenshan

2017-03-01

Stratabound deposits are the most abundant and economically significant ore type in the Middle-Lower Yangtze River Valley, one of the most important metallogenic belts in China. The Datuanshan deposit is one of the largest and most representative stratabound Cu(-Mo) deposits in the Tongling district of the Middle-Lower Yangtze River metallogenic belt. All the orebodies of the Datuanshan deposit occur around Mesozoic quartz monzodiorite and are tabular or semi-tabular bodies along bedding-parallel faults within upper Permian to Lower Triassic strata. However, discordant and crosscutting relationships (e.g., the host rocks crosscut by skarn- and quartz-sulfide veins, with alteration halos around the veins) have also been found, especially along the skarn-host contact and orebody-host contact, indicating that skarnitization and mineralization postdated the deposition of the host sediments. The skarn consists mainly of prograde garnet and pyroxene and retrograde alteration assemblages of amphibole, epidote, and chlorite, as well as quartz and sulfides. Electron microprobe analyses show that the garnets and pyroxenes are grossular-andradite and hedenbergite-diopside series, respectively, and all samples plot in the field of typical skarn copper deposits worldwide. Molybdenite samples from stratiform copper ores yield Re-Os model ages of 138.2-139.9 Ma with a weighted mean age of 139.2 ± 0.9 Ma. This is reasonably consistent with the ages of the stratiform Mo ores (138.0-140.8 Ma) and genetically related quartz monzodiorite (135.2-139.3 Ma) in the Datuanshan deposit, indicating that the stratiform Cu and Mo mineralization was contemporaneous with emplacement of the quartz monzodiorite magmas in the Early Cretaceous. Fifteen δ34S values for sulfides range from -1.8 to +4.7 ‰, with a mean of 0.5 ‰, indicating that the sulfur was derived mainly from a magmatic source. Moreover, the sulfur isotope values of the ores are consistent with those of Mesozoic intermediate

Tellurium, a guide to mineral deposits

USGS Publications Warehouse

Watterson, J.R.; Gott, G.B.; Neuerburg, G.J.; Lakin, H.W.; Cathrall, J.B.

1977-01-01

Te dispersion patterns are useful in exploring for different types of mineral deposits and in providing additional information about known ore deposits. The Te content of rocks is given for five mining districts in the western United States: Coeur d'Alene, Idaho; Robinson, near Ely, Nevada; Montezuma, Colorado; Crater Creek area, Colorado; Cripple Creek, Colorado. Many of the analyses were obtained by use of a new analytical method sensitive to 0.001 ppm Te. The principal ore deposits in the Coeur d'Alene district, Idaho, are Pb-Zn-Ag replacement veins in Precambrian rocks of the Belt Supergroup. Te dispersion patterns show the outlines of the original mineral belts, the effects of intrusive events, the location of ore deposits, the displacements caused by post-ore faulting, and the borders of the 780-km2 district. The disseminated porphyry Cu deposits of the Robinson mining district, Nevada, are associated with Cretaceous quartz monzonite stocks that have intruded Palaeozoic carbonate rocks. Te is present in rock samples in concentrations as high as 10,000 ppm and forms a halo around the areas containing the Cu deposits. The alteration zones in the porphyry Mo district near Montezuma, Colorado, are developed around several small Tertiary intrusions occurring along a regional shear zone. Te haloes reflect the locations of porphyry intrusives, individual deposits and their ore shoots, and the pattern and intensity of adjacent alteration. The Te content of soils over the Montezuma stock is higher than, and varies independently from, the Te content of adjacent outcrops. Soils generally contain more Te than adjacent outcropping rocks. Soil may collect gaseous Te compounds from mineral deposits. The Crater Creek area is a northwestern extension of the Summitville mining district, Colorado. Te dispersion patterns radiate out from exposed Cu-Pb-Zn veins, from an outcrop of molybdenite stockwork veins and from associated iron-stained altered rock. Te haloes intensify

3D inversion of SPECTREM and ZTEM airborne electromagnetic data from the Pebble Cu-Au-Mo porphyry deposit, Alaska

NASA Astrophysics Data System (ADS)

Pare, Pascal; Gribenko, Alexander V.; Cox, Leif H.; Čuma, Martin; Wilson, Glenn A.; Zhdanov, Michael S.; Legault, Jean; Smit, Jaco; Polome, Louis

2012-04-01

Geological, geochemical, and geophysical surveys have been conducted in the area of the Pebble Cu-Au-Mo porphyry deposit in south-west Alaska since 1985. This case study compares three-dimensional (3D) inversion results from Anglo American's proprietary SPECTREM 2000 fixed-wing time-domain airborne electromagnetic (AEM) and Geotech's ZTEM airborne audio-frequency magnetics (AFMAG) systems flown over the Pebble deposit. Within the commonality of their physics, 3D inversions of both SPECTREM and ZTEM recover conductivity models consistent with each other and the known geology. Both 3D inversions recover conductors coincident with alteration associated with both Pebble East and Pebble West. The high grade CuEqn 0.6% ore shell is not consistently following the high conductive trend, suggesting that the SPECTREM and ZTEM responses correspond in part to the sulphide distribution, but not directly with the ore mineralization. As in any exploration project, interpretation of both surveys has yielded an improved understanding of the geology, alteration and mineralization of the Pebble system and this will serve well for on-going exploration activities. There are distinct practical advantages to the use of both SPECTREM and ZTEM, so we draw no recommendation for either system. We can conclude however, that 3D inversion of both AEM and ZTEM surveys is now a practical consideration and that it has added value to exploration at Pebble.

Gold in the Black Hills, South Dakota, and how new deposits might be found

USGS Publications Warehouse

Norton, James Jennings

1974-01-01

metamorphic rocks of a grade just above the garnet isograd, in a zone where the principal iron-magnesium mineral of the iron-formation changes from a carbonate (sideroplesite) to a silicate (cummingtonite). This metamorphic reaction would release carbon dioxide to the fluid that presumably formed the ore bodies. In short, three controls over localization of the ore have been identified: (1) the cross folds; (2) the so-called Homestake Formation, which passes beneath Paleozoic rocks north of Lead and has not been proved to reappear anywhere else in the Black Hills (Other units of iron-formation less enriched in gold might locally become more like the Homestake Formation beneath the cover of Paleozoic rocks.}; (3} proximity to the garnet isograd--nearly all the exposed Precambrian rocks in the Black Hills are at a metamorphic grade higher than this isograd--and occurrence of this isograd zone mostly beneath Paleozoic rocks. In searching for new deposits, one can guess from existing data where Precambrian rocks of suitable nature may be concealed. The usefulness of such guesses can be increased if they are made with information about the distribution of gold in younger rocks. Gold in the Deadwood basal conglomerate would be the simplest indicator of a deposit once exposed on the pre-Deadwood surface. Tertiary replacement deposits in the Deadwood or other rocks, which obtained their gold from Precambrian sources that may be nearby or far away, can also be helpful; they, like anomalies found by geochemical sampling, at least outline the regions of mineralizing activity. A suitable approach to exploration is to make a thorough study of the stratigraphy, the structure, and the metals geochemistry of the Deadwood Formation and associated rocks, chiefly in the northern Black Hills but to a lesser extent elsewhere in localities where the Precambrian geology seems promising and where gold has been found nearby. Such a program, even if it does not yield

Geology of the Midnite uranium mine, Stevens County, Washington; a preliminary report

USGS Publications Warehouse

Nash, J. Thomas; Lehrman, Norman J.

1975-01-01

The Midnite mine is one of only two mines in the United States currently producing uranium from discordant deposits in crystalline host rocks. Ore bodies are in metamorphosed steeply dipping Precambrian pelitic and calcareous rocks of a roof pendant adjacent to a Cretaceous(?) porphyritic quartz monzonite pluton. Production during 14 years, of operation has been about 8 million pounds of U3O8 from oxidized and reduced ores averaging 0.23 percent U3O8. Uranium deposits are generally tabular in form and dimensions range up to 380 m long, 210 m wide, and 50 m thick. Deposits are bounded on at least one side by unmineralized intrusive ribs of granitic rock, and thickest mineralized zones invariably occur at depressions in the intrusive contact. Upper limits of some deposits are nearly horizontal, and upper elevations of adjacent mineralized zones separated by ribs of granite are similar. Near surface ore is predominantly autunite, but ore at depth consists of pitchblende and coffinite with abundant pyrite and marcasite. Uranium minerals occur as .disseminations along foliation, replacements, and stockwork fracture-fillings. No stratigraphic controls on ore deposition are recognized. Rather, mineralized zones cut across lithologic boundaries if permeability is adequate. Most ore is in muscovite schist and mica phyllite, but important deposits occur in calc-silicate hornfels. Amphibolite sills and mid-Tertiary dacite dikes locally, carry ore where intensely fractured. High content of iron and sulfur, contained chiefly in FeS2, appear to be an important feature of favorable host rocks. Geometry of deposits, structural, and geochemical features suggest that uranium minerals were deposited over a span of time from late Cretaceous to late Tertiary. Ore occurs in but is not offset by a shear zone that displaces mid-Tertiary rocks.. Economic zones of uranium are interpreted to have been secondarily enriched in late Tertiary time by downward and lateral migration of uranium

An occurrence model for the national assessment of volcanogenic beryllium deposits

USGS Publications Warehouse

Foley, Nora K.; Seal, Robert R.; Piatak, Nadine M.; Hetland, Brianna

2010-01-01

The general occurrence model summarized here is intended to provide a descriptive basis for the identification and assessment of undiscovered beryllium deposits of a type and style similar to those found at Spor Mountain, Juab County, Utah. The assessment model is restricted in its application in order to provide a coherent basis for assessing the probability of the occurrence of similar economic deposits using the current U.S. Geological Survey methodology. The model is intended to be used to identify tracts of land where volcanogenic epithermal replacement-type beryllium deposits hosted by metaluminous to peraluminous rhyolite are most likely to occur. Only a limited number of deposits or districts of this type are known, and only the ores of the Spor Mountain district have been studied in detail. The model highlights those distinctive aspects and features of volcanogenic epithermal beryllium deposits that pertain to the development of assessment criteria and puts forward a baseline analysis of the geoenvironmental consequences of mining deposits of this type.

Control of Rock Mechanics in Underground Ore Mining

NASA Astrophysics Data System (ADS)

Golik, V. I.; Efremenkov, A. B.

2017-07-01

Performance indicators in underground mining of thick iron fields can be insufficient since geo-mechanic specifics of ore-hosting fields might be considered inadequately, as a consequence, critical deformations and even earth’s surface destruction are possible, lowering the indicators of full subsurface use, this way. The reason for it is the available approach to estimating the performance of mining according to ore excavation costs, without assessing losses of valuable components and damage to the environment. The experimental approach to the problem is based on a combination of methods to justify technical capability and performance of mining technology improvement with regard to geomechanical factors. The main idea of decisions to be taken is turning geo-materials into the condition of triaxial compression via developing the support constructions of blocked up structural rock block. The study was carried out according to an integrated approach based on the analysis of concepts, field observations, and simulation with the photo-elastic materials in conditions of North Caucasus deposits. A database containing information on the deposit can be developed with the help of industrial experiments and performance indicators of the field can be also improved using the ability of ore-hosting fields to develop support constructions, keeping the geo-mechanical stability of the system at lower cost, avoiding ore contamination at the processing stage. The proposed model is a specific one because an adjustment coefficient of natural and anthropogenic stresses is used and can be adopted for local conditions. The relation of natural to anthropogenic factors can make more precise the standards of developed, prepared and ready to excavation ore reserves relying on computational methods. It is possible to minimize critical stresses and corresponding deformations due to dividing the ore field into sectors safe from the standpoint of geo-mechanics, and using less cost

Magnetic properties of the Bled El Hadba phosphate-bearing formation (Djebel Onk, Algeria): Consequences of the enrichment of the phosphate ore deposit

NASA Astrophysics Data System (ADS)

Bezzi, Nacer; Aïfa, Tahar; Merabet, Djoudi; Pivan, Jean-Yves

2008-02-01

To improve the enrichment of the Thanetian marine phosphate ore deposit from the quarry of Bled El Hadba (Djebel Onk, Algeria) before its exploitation, we first conducted a joint study using different techniques for comparison. These studies reveal that magnetic minerals play a significant role within the matrix of the central productive unit which is squeezed between two other units. Magnetic separation procedures show that there are some positive correlations between magnetic susceptibility and grain size fraction (80-250 μm). These dolomite-rich fractions are more clearly separated. Different tools were used to characterize the magnetic minerals (X-ray, microprobe, differential scanning calorimetry, thermogravimetric and thermomagnetic analyses). They show correlations between magnetic phases and the presence of associated magnetic minerals within the matrix or included in the phosphate ore deposit. They enabled us to distinguish a series of magnetic minerals (magnetite, hematite, maghemite, goethite, ilmenite, pyrite, iron-titanium oxide and titanium oxide sulphate) and to determine that Fe and Ti are prevalent in the separated fractions, following the same variation as Mg. The phosphorous (phosphate) rate is higher in the non-magnetic material, especially in the layers that are rich in dolomitic carbonates (upper and lower units), which could be trapped within the dolomitic matrix, while Magnesium (dolomite) is more important in the magnetic fraction. The separation of phosphate elements and dolomite carbonates is effective and therefore the ore can be enriched through magnetic procedures. Comparison between products enriched by magnetic separation, flotation and calcination showed important differences, chemically, economically and technically speaking.

Sustainable rehabilitation of mining waste and acid mine drainage using geochemistry, mine type, mineralogy, texture, ore extraction and climate knowledge.

PubMed

Anawar, Hossain Md

2015-08-01

The oxidative dissolution of sulfidic minerals releases the extremely acidic leachate, sulfate and potentially toxic elements e.g., As, Ag, Cd, Cr, Cu, Hg, Ni, Pb, Sb, Th, U, Zn, etc. from different mine tailings and waste dumps. For the sustainable rehabilitation and disposal of mining waste, the sources and mechanisms of contaminant generation, fate and transport of contaminants should be clearly understood. Therefore, this study has provided a critical review on (1) recent insights in mechanisms of oxidation of sulfidic minerals, (2) environmental contamination by mining waste, and (3) remediation and rehabilitation techniques, and (4) then developed the GEMTEC conceptual model/guide [(bio)-geochemistry-mine type-mineralogy- geological texture-ore extraction process-climatic knowledge)] to provide the new scientific approach and knowledge for remediation of mining wastes and acid mine drainage. This study has suggested the pre-mining geological, geochemical, mineralogical and microtextural characterization of different mineral deposits, and post-mining studies of ore extraction processes, physical, geochemical, mineralogical and microbial reactions, natural attenuation and effect of climate change for sustainable rehabilitation of mining waste. All components of this model should be considered for effective and integrated management of mining waste and acid mine drainage. Copyright © 2015 Elsevier Ltd. All rights reserved.

Stratabound copper-silver deposits of the Mesoproterozoic Revett formation, Montana and Idaho

USGS Publications Warehouse

Boleneus, David E.; Appelgate, Larry M.; Stewart, John H.; Zientek, Michael L.

2005-01-01

The western Montana copper belt in western Montana and northern Idaho contains several large stratabound copper-silver deposits in fine- to medium-grained quartzite beds of the Revett Formation of the Mesoproterozoic (1,470-1,401 Ma) Belt Supergroup. Production from the deposits at the Troy Mine and lesser production from the Snowstorm Mine has yielded 222,237 tons Cu and 1,657.4 tons Ag. Estimates of undeveloped resources, mostly from the world-class Rock Creek-Montanore deposits, as well as lesser amounts at the Troy Mine, total more than 2.9 million tons Cu and 2,600 tons Ag in 406 million tons of ore.The Rock Creek-Montanore and Troy deposits, which are currently the most significant undeveloped resources identified in the copper belt, are also among the largest stratabound copper-silver deposits in North America and contain about 15 percent of the copper in such deposits in North America. Worldwide, stratabound copper-silver deposits contain 23 percent of all copper resources and are the second-most important global source of the metal after porphyry copper deposits.The Revett Formation, which consists of subequal amounts of argillite, siltite, and quartzite, is informally divided into lower, middle, and upper members on the basis of the proportions of the dominant rock types. The unit thickness increases from north to south, from 1,700 ft near the Troy Mine, 55 mi north of Wallace, Idaho, to more than 5,300 ft at Wallace, Idaho, in the Coeur d'Alene Trough south of the Osburn Fault, a major right-lateral strike-slip fault.Mineral deposits in the Revett Formation occur mostly in the A-D beds of the lower member and in the middle quartzite of the upper member. The deposits are concentrated along a preore pyrite/hematite interface in relatively coarse grained, thick quartzite beds that acted as paleoaquifers for ore fluids. The deposits are characterized by mineral zones (alteration-mineral assemblages) that are a useful guide to the locations of mineral

Te-Rich argyrodite occurrence in Roşia Montană ore deposit, Apuseni Mountains, Romania

NASA Astrophysics Data System (ADS)

Bailly, Laurent; Tămaş, Călin-Gabriel; Minuţ, Adrian

2005-06-01

A new argyrodite occurrence has been discovered in the Roşia Montană ore deposit located in the South Apuseni Mountains, Romania. Argyrodite is associated with common base metal sulfides and sulfosalts (galena, sphalerite, chalcopyrite, tetrahedrite ± alabandite, pyrite, and marcasite), tellurides (hessite, altaite, sylvanite) and rare electrum grains in the Ag-rich Cârnicel vein hosted by an extracraterial phreatomagmatic breccia within the Cârnic massif. SEM and EPMA analyses revealed that this argyrodite is Te-rich and a mean Ag 8.04Ge 0.9Te 2.07S 3.77 formula was calculated. This phase could be the germaniferous equivalent of the previously-described Te-rich canfieldite. To cite this article: L. Bailly et al., C. R. Geoscience 337 (2005).

2D Inversion of DCR and Time Domain IP data: an example from ore exploration

NASA Astrophysics Data System (ADS)

Adrian, J.; Tezkan, B.

2015-12-01

Ore deposits often appear as disseminated sulfidic materials. Exploring these deposits with the Direct Current Resistivity (DCR) method alone is challenging because the resistivity signatures caused by disseminated material is often hard to detect. The Time-domain Induced Polarization (TDIP) method, on the other hand, is qualified to detect areas with disseminated sulfidic ores due to large electrode polarization effects which result in large chargeability anomalies. By employing both methods we gain information about both, the resistivity and the chargeability distribution of the subsurface.On the poster we present the current state of the development of a 2D smoothness constraint inversion algorithm for DCR and TDIP data. The implemented forward algorithm uses a Finite Element approach with an unstructured mesh. The model parameters resistivity and chargeability are connected by either a simple conductivity pertubation approach or a complex conductivity approach.As a case study, the 2D inversion results of DCR/TDIP and RMT data obtained during a survey on a sulfidic copper ore deposit in Turkey are presented. The presence of an ore deposit is indicated by areas with low resistivity and significantly high chargeability in the inversion models.This work is part of the BMBF/TUEBITAK funded project ``Two-dimensional joint interpretation of Radiomagnetotellurics (RMT), Direct Current Resistivity (DCR) and Induced Polarization (IP) data: an example from ore exploration''.

The physical hydrology of magmatic-hydrothermal systems: High-resolution 18O records of magmatic-meteoric water interaction from the Yankee Lode tin deposit (Mole Granite, Australia)

NASA Astrophysics Data System (ADS)

Fekete, Szandra; Weis, Philipp; Driesner, Thomas; Heinrich, Christoph A.; Baumgartner, Lukas; Bouvier, Anne-Sophie

2016-04-01

apparent discrepancy can be explained by the presence of a fluid of meteoric origin that was isotopically equilibrated with a hot, but already solidified and fractured granitic intrusion under rock-dominated conditions prior their transfer to the cold ore deposition site (Heinrich, 1990). Conversely, in porphyry copper systems meteoric fluid incursion has been assumed to participate in formation of peripheral or post-mineralization processes (Bowman et al., 1987; Sillitoe, 2010; Williams-Jones and Migdisov, 2014). However, recent numerical simulations of porphyry copper systems identify a significant role of meteoric fluids for the enrichment process, providing a cooling mechanism for metal-rich fluids expelled from an upper crustal magma chamber (Weis et al. 2012, Weis 2015). Furthermore, new petrographic and fluid inclusion work of ore-mineralized quartz veins (Landtwing et al., 2010; Stefanova et al., 2014) indicates lower (˜ 450r{ }C) than magmatic fluid temperatures for copper precipitation. Given that the Yankee Lode study validated the capability of high resolution, in situ δ 18O analysis to trace meteoric water incursion, we will apply this method to hydrothermal quartz samples from two significant porphyry copper deposits (Bingham Canyon, USA and Elatsite, Bulgaria). By this we intend to better constrain a potential role of meteoric water incursion in porphyry copper ore precipitation. REFERENCES Audétat, A., Günther, D., Heinrich, C. A. 1998: Formation of a Magmatic-Hydrothermal Ore Deposit: Insights with LA-ICP-MS Analysis of Fluid Inclusions: Science, 279, 2091-2094. Audétat, A. 1999: The magmatic-hydrothermal evolution of the Sn/W-mineralized Mole Granite (Eastern Australia): PhD Thesis, 211. Bowman, J. R., Parry, W. T., Kropp, W. P., and Kruer, S. A., 1987: Chemical and isotopic evolution of hydrothermal solutions at Bingham, Utah: Economic Geology, 82, 395-428. Heinrich, C.A. 1990: The Chemistry of Hydrothermal Tin(-Tungsten) Ore Deposition: Economic

Sulphur isotope constraints on formation conditions of the Luiswishi ore deposit, Democratic Republic of Congo (DRC)

NASA Astrophysics Data System (ADS)

Lerouge, C.; Cailteux, J.; Kampunzu, A. B.; Milesi, J. P.; Fléhoc, C.

2005-07-01

Luiswishi is a Congo-type Neoproterozoic sediment-hosted stratiform Cu-Co ore deposit of the Central Africa Copperbelt, located northwest of Lubumbashi (DRC). The ores form two main Cu-Co orebodies hosted by the Mines Subgroup, one in the lower part of the Kamoto Formation and the other at the base of the Dolomitic Shales Formation. Sulphides occur essentially as early parallel layers of chalcopyrite and carrolite, and secondarily as late stockwork sulphides cross-cutting the bedding and the early sulphide generation. Both types of stratiform and stockwork chalcopyrite and carrolite were systematically analyzed for sulphur isotopes, along the lithostratigraphic succession of the Mine Series. The quite similar δ 34S values of stratiform sulphides and late stockwork sulphides suggest an in situ recrystallization or a slight remobilization of stockwork sulphides without attainment of isotopic equilibrium between different sulphide phases (chalcopyrite and carrolite). The distribution of δ 34S values (-14.4‰ to +17.5‰) combined with the lithology indicates a strong stratigraphic control of the sulphur isotope signature, supporting bacterial sulphate reduction during early diagenesis of the host sediments, in a shallow marine to lacustrine environment. Petrological features combined with sulphur isotopic data of sulphides at Luiswishi and previous results on nodules of anhydrite in the Mine Series indicate a dominant seawater/lacustrine origin for sulphates, precluding a possible hydrothermal participation. The high positive δ 34S values of sulphides in the lower orebody at Luiswishi, hosted in massive chloritic-dolomitic siltite (known as Grey R.A.T.), fine-grained stratified dolostone (D.Strat.) and silicified-stromatolitic dolomites alternating with chloritic-dolomitic silty beds (R.S.F.), suggest that they were probably deposited during a period of regression in a basin cut off from seawater. The variations of δ 34S values (i.e. the decrease of δ 34S values

Did the Kiruna iron ores form as a result of a metasomatic or igneous process? New U-Pb and Nd data for the iron oxide apatite ores and their host rocks in the Norrbotten region of northern Sweden

NASA Astrophysics Data System (ADS)

Westhues, A.; Hanchar, J. M.; Whitehouse, M. J.; Fisher, C. M.

2012-12-01

A number of iron deposits near Kiruna in the Norrbotten region of northern Sweden are of the iron oxide apatite (IOA) type of deposits; also referred to as Kiruna-type deposits. They are commonly considered a subgroup or end-member of iron oxide copper gold (IOCG) deposits, containing no economic grades of copper or gold. Both IOCG and IOA deposits are characterized by abundant low-Ti Fe oxides, an enrichment in REE, and intense sodium and potassium wall-rock alteration adjacent to the ores. Deposits of these types are of a great economic importance, not only for iron, but also for other elements such as rare earth elements (REE) or uranium. Kiruna, the type locality of the IOA type of mineral deposits, is the focus of this study. Despite a century-long mining history and 2500 Mt of iron ore produced in the region to date (with grades of 30 to 70 wt.% Fe), the genesis of these deposits is poorly understood: theories of a magmatic vs. a hydrothermal or metasomatic origin have been debated, and the timing of mineralization of the ores in the Norbotten region has never been directly dated. The results anticipated from this study will provide a better understanding of the nature of the IOA type of mineral deposits and their relation to IOCG deposits such as Olympic Dam in Australia. An array of geochemical methods is used in order to gain insights on the emplacement history of the host rocks, their subsequent alteration, and the ore genesis of these deposits. This includes in situ U/Pb geochronology of zircon, monazite, and titanite to constrain the timing between host rock emplacement, alteration and mineralization. Isotopic data from whole rocks and in situ at mineral scale will provide constraints on the involvement of hydrothermal fluids and their possible sources, as well as on the sources of Fe, U, and the REE. Newly obtained Sm-Nd isotopic data points to distinct source differences between host rocks, ore and alteration related samples. Preliminary in situ U

Precambrian Sulphide Deposits

NASA Astrophysics Data System (ADS)

Doe, Bruce R.

1984-04-01

This book is dedicated to Howard S. Robinson, who was born and educated in the United States, but who spent his professional career in Canada with McIntyre Porcupine Mines, concentrating on Precambrian mineral deposits. Although his career in mineral exploration was distinguished, his major contribution to earth science was probably as one of the founders of the Geological Association of Canada, an institution to which he made a bequest in his will. With this background, the strong emphasis on Canadian Precambrian mineral deposits should come as no surprise; of the 23 papers in this book, 21 are solely or primarily devoted to Canadian deposits. The two exceptions—those describing the Balmat, N.Y., zinc mines (at times the largest zinc producer in the United States) and the Crandon, Wisconsin, volcanogenic zinc-copper massive-sulfide deposit (the largest deposit of its kind found in the 1970s)—are each within a couple of hundred kilometers of the Canadian border. Although the title of the book is more expansive than the actual topics discussed, Canada is rich in Precambrian rocks and ore bodies, and Canadian scientists have been especially alert to tectonic influences in the formation of mineral deposits. These features, plus the fact that the country contains a very well exposed expanse of Archean rocks which is the largest in the world, facilitate the study of early crustal evolution and make the book of particular interest to geophysicists.

Use of the high-resolution satellite images for detection of fractures related to the ore deposits

NASA Astrophysics Data System (ADS)

Cruz-Mondaca, M.; Soto-Pinto, C. A.; Arellano-Baeza, A. A.

2012-12-01

The Aster and GeoEye satellite high-resolution images were used to detect the structures related to the fracturing of the upper crust in the North of Chile. In particular, lineament analysis has been applied to detect the presence of epithermal fluids of low sulfurization associated with the Paleozoic ore deposits. These results have been compared with the location of the minerals altered by the presence of geothermal fluids detected using the spectral libraries. Later, the presence of fractures has been corroborated during recognition of fractures in situ and the geochemical analysis of samples of minerals altered by the presence of fluids. It was shown that the results obtained are relevant for the gold vein detection.

Data set of world phosphate mines, deposits, and occurrences: Part A. geologic data; Part B. location and mineral economic data

USGS Publications Warehouse

Chernoff, Carlotta B.; Orris, G.J.

2002-01-01

An inventory of more than 1,600 world phosphate mines, deposits, and occurrences was compiled from smaller data sets collected as part of multiple research efforts by Carlotta Chernoff, University of Arizona, and Greta Orris, U.S. Geological Survey. These data have been utilized during studies of black shale depositional environments and to construct phosphate deposit models. The compiled data have been edited for consistency and additional location information has been added where possible. The database of compiled phosphate information is being released in two sections; the geologic data in one section and the location and mineral economic data in the second. This report, U.S. Geological Survey Open-File Report 02–156–A, contains the geologic data and is best used with the complimentary data contained in Open-File Report 02–156–B. U.S. Geological Survey Open-File Report 02–156–B contains commodity data, location and analytical data, a variety of mineral economic data, reference information, and pointers to related records in the U.S. Geological Survey National mineral databases—MASMILS and MRDS.

Summary of the mineralogy of the Colorado Plateau uranium ores

USGS Publications Warehouse

Weeks, Alice D.; Coleman, Robert Griffin; Thompson, Mary E.

1956-01-01

In the Colorado Plateau uranium has been produced chiefly from very shallow mines in carnotite ores (oxidized vanadiferous uranium ores) until recent deeper mining penetrated black unoxidized ores in water-saturated rocks and extensive exploration has discovered many deposits of low to nonvanadiferous ores. The uranium ores include a wide range from highly vanadiferous and from as much as one percent to a trace of copper, and contain a small amount of iron and traces of lead, zinc, molybdenum, cobalt, nickel, silver, manganese, and other metals. Recent investigation indicates that the carnotite ores have been derived by progressive oxidation of primary (unoxidized) black ores that contain low-valent uranium and vanadium oxides and silicates. The uranium minerals, uraninite and coffinite, are associated with coalified wood or other carbonaceous material. The vanadium minerals, chiefly montroseite, roscoelite, and other vanadium silicates, occur in the interstices of the sandstone and in siltstone and clay pellets as well as associated with fossil wood. Calcite, dolomite, barite and minor amounts of sulfides, arsenides, and selenides occur in the unoxidized ore. Partially oxidized vanadiferous ore is blue black, purplish brown, or greenish black in contrast to the black or dark gray unoxidized ore. Vanadium combines with uranium to form rauvite. The excess vanadium is present in corvusite, fernandinite, melanovanadite and many other quadrivalent and quinquevalent vanadium minerals as well as in vanadium silicates. Pyrite and part or all of the calcite are replaced by iron oxides and gypsum. In oxidized vanadiferous uranium ores the uranium is fixed in the relatively insoluble minerals carnotite and tyuyamunite, and the excess vanadium commonly combines with one or more of the following: calcium, sodium, potassium, magnesium, aluminum, iron, copper, manganese, or barium, or rarely it forms the hydrated pentoxide. The relatively stable vanadium silicates are little

Geology and recognition criteria for veinlike uranium deposits of the lower to middle Proterozoic unconformity and strata-related types. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dahlkamp, F.J.; Adams, S.S.

1981-01-01

The discovery of the Rabbit Lake deposit, Saskatchewan, in 1968 and the East Alligator Rivers district, Northern Territory, Australia, in 1970 established the Lower-Middle Proterozoic veinlike-type deposits as one of the major types of uranium deposits. The term veinlike is used in order to distinguish it from the classical magmatic-hydrothermal vein or veintype deposits. The veinlike deposits account for between a quarter and a third of the Western World's proven uranium reserves. Lower-Middle Proterozoic veinlike deposits, as discussed in this report include several subtypes of deposits, which have some significantly different geologic characteristics. These various subtypes appear to have formedmore » from various combinations of geologic processes ranging from synsedimentary uranium precipitation through some combination of diagenesis, metamorphism, metasomatism, weathering, and deep burial diagenesis. Some of the deposit subtypes are based on only one or two incompletely described examples; hence, even the classification presented in this report may be expected to change. Geologic characteristics of the deposits differ significantly between most districts and in some cases even between deposits within districts. Emphasis in this report is placed on deposit descriptions and the interpretations of the observers.« less

Luminescence dating of quaternary deposits in geology in Brazil.

PubMed

Tatumi, Sonia Hatsue; Gozzi, Giuliano; Yee, Márcio; de Oliveira, Victor Inácio; Sallun, Alethéa Ernandes Martins; Suguio, Kenitiro

2006-01-01

In the present work, systematic dating by luminescence methods has been done on 50 Quaternary geological samples within the study area of São Paulo State, Brazil. Bleaching experiments showed that residual TL intensity of 375 degrees C peak, of the quartz, was obtained after 10 h of sunlight exposition. Intensities decays of the 325 and 375 degrees C TL peaks can be fitted using second order exponential equation. Paleodose values were evaluated using regeneration methods with multiple aliquots. Samples dated indicate preliminary ages varying from 9 +/- 1 to 935 +/- 130 ka for colluvio-elluvial deposits, and from 17 +/- 2 to 215 +/- 30 ka for alluvial deposits of the study area. They cover four peneplained surfaces shaped during the Quaternary: I (1000-400 ka), II (400-120 ka), III (120-10 ka) and IV (10 ka until today), in decreasing order.

Long-Term Planning for Open Pits for Mining Sulphide-Oxide Ores in Order to Achieve Maximum Profit

NASA Astrophysics Data System (ADS)

Kržanović, Daniel; Conić, Vesna; Stevanović, Dejan; Kolonja, Božo; Vaduvesković, Jovan

2017-12-01

Profitable exploitation of mineralised material from the earth's crust is a complex and difficult task that depends on a comprehensive planning process. Answering the question of how to plan production depends on the geometry of the deposit, as well as the concentration, distribution, and type of minerals in it. The complex nature of mineral deposits largely determines the method of exploitation and profitability of mining operations. In addition to unit operating costs and metal prices, the optimal recovery of and achievement of maximum profit from deposits of sulphide-oxide ores also depend, to a significant extent, on the level of technological recovery achieved in the ore processing procedure. Therefore, in defining a long-term development strategy for open pits, special attention must be paid to the selection of an optimal procedure for ore processing in order to achieve the main objective: maximising the Net Present Value (NPV). The effect of using two different processes, flotation processing and hydrometallurgical methods (bioleaching acid leaching), on determining the ultimate pit is shown in the case of the Kraku Bugaresku-Cementacija sulphide-oxide ore deposit in eastern Serbia. Analysis shows that the application of hydrometallurgical methods of processing sulphide-oxide ore achieved an increase in NPV of 20.42%.

Mercury from mineral deposits and potential environmental impact

USGS Publications Warehouse

Rytuba, J.J.

2003-01-01

Mercury deposits are globally distributed in 26 mercury mineral belts. Three types of mercury deposits occur in these belts: silica-carbonate, hot-spring, and Almaden. Mercury is also produced as a by-product from several types of gold-silver and massive sulfide deposits, which account for 5% of the world's production. Other types of mineral deposits can be enriched in mercury and mercury phases present are dependent on deposit type. During processing of mercury ores, secondary mercury phases form and accumulate in mine wastes. These phases are more soluble than cinnabar, the primary ore mineral, and cause mercury deposits to impact the environment more so than other types of ore deposits enriched in mercury. Release and transport of mercury from mine wastes occur primarily as mercury-enriched particles and colloids. Production from mercury deposits has decreased because of environmental concerns, but by-product production from other mercury-enriched mineral deposits remains important.

Statistical studies of selected trace elements with reference to geology and genesis of the Carlin gold deposit, Nevada

USGS Publications Warehouse

Harris, Michael; Radtke, Arthur S.

1976-01-01

Linear regression and discriminant analyses techniques were applied to gold, mercury, arsenic, antimony, barium, copper, molybdenum, lead, zinc, boron, tellurium, selenium, and tungsten analyses from drill holes into unoxidized gold ore at the Carlin gold mine near Carlin, Nev. The statistical treatments employed were used to judge proposed hypotheses on the origin and geochemical paragenesis of this disseminated gold deposit.

Interpreting geologic maps for engineering purposes: Hollidaysburg quadrangle, Pennsylvania

USGS Publications Warehouse

,

1953-01-01

This set of maps has been prepared to show the kinds of information, useful to engineers, that can be derived from ordinary geologic maps. A few additional bits of information, drawn from other sources, are mentioned below. Some of the uses of such maps are well known; they are indispensable tools in the modern search for oil or ore deposits; they are the first essential step in unraveling the story of the earth we live on. Less well known, perhaps, is the fact that topographic and geologic maps contain many of the basic data needed for planning any engineering construction job, big or little. Any structure built by man must fit into the topographic and geologic environment shown on such maps. Moreover, most if not all construction jobs must be based on knowledge of the soils and waters, which also are intimately related to this same environment. The topographic map shows the shape of the land the hills and valleys, the streams and swamps, the man-made features such as roads, railroads, and towns. The geologic map shows the kinds and shapes of the rock bodies that form the land surface and that lie beneath it. These are the facts around which the engineer must build.

The formation age of ores from the Pebble Cu-Au-Mo giant deposit (Alaska, United States)

NASA Astrophysics Data System (ADS)

Kremenetskii, A. A.; Popov, V. S.; Gromalova, N. A.

2012-02-01

Zircons from the porphyry-like quartz-diorite boss of the Pebble Cu-Au-Mo deposit (southwest Alaska) have been examined. By their appearance and internal structure (cathode luminescence and electron probing), the zircons have been subdivided into four genetic groups: (1) xenogenic detrital (mainly rounded); (2) magmatogene (protolith crystal in the center and growth zone at the edge); (3) hydrothermally altered (with new-formed regeneration edges in growth zones); (4) metamict-altered (unconsolidated center of the crystal and sectoring in growth zones). Based on SHRIMP U-Pb dating for the principal heterogeneous elements in every group, the following stages of ore formation have been identified for the Pebble deposit: (a) crystallization of quartz diorite-porphyry bosses (95-92 Ma, the concordant age is 94.7 ± 1.5 Ma); (b) late magmatic metasomatic alterations with copper-molybdenum mineralization (92-85 Ma, the concordant age is 90.15 ± 0.78 Ma); (c) postmagmatic argillization with epithermal gold-sulfide mineralization (82-80 Ma, the concordant age is 82.9 ± 2.7 Ma).

Database for geologic maps of pyroclastic-flow and related deposits of the 1980 eruptions of Mount St. Helens, Washington

USGS Publications Warehouse

Furze, Andrew J.; Bard, Joseph A.; Robinson, Joel; Ramsey, David W.; Kuntz, Mel A.; Rowley, Peter D.; MacLeod, Norman S.

2017-10-31

This publication releases digital versions of the geologic maps in U.S. Geological Survey Miscellaneous Investigations Map 1950 (USGS I-1950), “Geologic maps of pyroclastic-flow and related deposits of the 1980 eruptions of Mount St. Helens, Washington” (Kuntz, Rowley, and MacLeod, 1990) (https://pubs.er.usgs.gov/publication/i1950). The 1980 Mount St. Helens eruptions on May 18, May 25, June 12, July 22, August 7, and October 16–18 produced pyroclastic-flow and related deposits. The distribution and morphology of these deposits, as determined from extensive field studies and examination of vertical aerial photographs, are shown on four maps in I-1950 (maps A–D) on two map sheets. Map A shows the May 18, May 25, and June 12 deposits; map B shows the July 22 deposits; map C shows the August 7 deposits; and map D shows the October 16–18 deposits. No digital geospatial versions of the geologic data were made available at the time of publication of the original maps. This data release consists of attributed vector features, data tables, and the cropped and georeferenced scans from which the features were digitized, in order to enable visualization and analysis of these data in GIS software. This data release enables users to digitally re-create the maps and description of map units of USGS I-1950; map sheet 1 includes text sections (Introduction, Physiography of Mount St. Helens at the time of the 1980 eruptions, Processes of the 1980 eruptions, Deposits of the 1980 eruptions, Limitations of the maps, Preparation of the maps, and References cited) and associated tables and figures that are not included in this data release.

Linking geological and health sciences to assess childhood lead poisoning from artisanal gold mining in Nigeria.

PubMed

Plumlee, Geoffrey S; Durant, James T; Morman, Suzette A; Neri, Antonio; Wolf, Ruth E; Dooyema, Carrie A; Hageman, Philip L; Lowers, Heather A; Fernette, Gregory L; Meeker, Gregory P; Benzel, William M; Driscoll, Rhonda L; Berry, Cyrus J; Crock, James G; Goldstein, Harland L; Adams, Monique; Bartrem, Casey L; Tirima, Simba; Behbod, Behrooz; von Lindern, Ian; Brown, Mary Jean

2013-06-01

In 2010, Médecins Sans Frontières discovered a lead poisoning outbreak linked to artisanal gold processing in northwestern Nigeria. The outbreak has killed approximately 400 young children and affected thousands more. Our aim was to undertake an interdisciplinary geological- and health-science assessment to clarify lead sources and exposure pathways, identify additional toxicants of concern and populations at risk, and examine potential for similar lead poisoning globally. We applied diverse analytical methods to ore samples, soil and sweep samples from villages and family compounds, and plant foodstuff samples. Natural weathering of lead-rich gold ores before mining formed abundant, highly gastric-bioaccessible lead carbonates. The same fingerprint of lead minerals found in all sample types confirms that ore processing caused extreme contamination, with up to 185,000 ppm lead in soils/sweep samples and up to 145 ppm lead in plant foodstuffs. Incidental ingestion of soils via hand-to-mouth transmission and of dusts cleared from the respiratory tract is the dominant exposure pathway. Consumption of water and foodstuffs contaminated by the processing is likely lesser, but these are still significant exposure pathways. Although young children suffered the most immediate and severe consequences, results indicate that older children, adult workers, pregnant women, and breastfed infants are also at risk for lead poisoning. Mercury, arsenic, manganese, antimony, and crystalline silica exposures pose additional health threats. Results inform ongoing efforts in Nigeria to assess lead contamination and poisoning, treat victims, mitigate exposures, and remediate contamination. Ore deposit geology, pre-mining weathering, and burgeoning artisanal mining may combine to cause similar lead poisoning disasters elsewhere globally.

Linking Geological and Health Sciences to Assess Childhood Lead Poisoning from Artisanal Gold Mining in Nigeria

PubMed Central

Durant, James T.; Morman, Suzette A.; Neri, Antonio; Wolf, Ruth E.; Dooyema, Carrie A.; Hageman, Philip L.; Lowers, Heather A.; Fernette, Gregory L.; Meeker, Gregory P.; Benzel, William M.; Driscoll, Rhonda L.; Berry, Cyrus J.; Crock, James G.; Goldstein, Harland L.; Adams, Monique; Bartrem, Casey L.; Tirima, Simba; Behbod, Behrooz; von Lindern, Ian; Brown, Mary Jean

2013-01-01

Background: In 2010, Médecins Sans Frontières discovered a lead poisoning outbreak linked to artisanal gold processing in northwestern Nigeria. The outbreak has killed approximately 400 young children and affected thousands more. Objectives: Our aim was to undertake an interdisciplinary geological- and health-science assessment to clarify lead sources and exposure pathways, identify additional toxicants of concern and populations at risk, and examine potential for similar lead poisoning globally. Methods: We applied diverse analytical methods to ore samples, soil and sweep samples from villages and family compounds, and plant foodstuff samples. Results: Natural weathering of lead-rich gold ores before mining formed abundant, highly gastric-bioaccessible lead carbonates. The same fingerprint of lead minerals found in all sample types confirms that ore processing caused extreme contamination, with up to 185,000 ppm lead in soils/sweep samples and up to 145 ppm lead in plant foodstuffs. Incidental ingestion of soils via hand-to-mouth transmission and of dusts cleared from the respiratory tract is the dominant exposure pathway. Consumption of water and foodstuffs contaminated by the processing is likely lesser, but these are still significant exposure pathways. Although young children suffered the most immediate and severe consequences, results indicate that older children, adult workers, pregnant women, and breastfed infants are also at risk for lead poisoning. Mercury, arsenic, manganese, antimony, and crystalline silica exposures pose additional health threats. Conclusions: Results inform ongoing efforts in Nigeria to assess lead contamination and poisoning, treat victims, mitigate exposures, and remediate contamination. Ore deposit geology, pre-mining weathering, and burgeoning artisanal mining may combine to cause similar lead poisoning disasters elsewhere globally. PMID:23524139

Linking geology and health sciences to assess childhood lead poisoning from artisanal gold mining in Nigeria

USGS Publications Warehouse

Plumlee, Geoffrey S.; Durant, James T.; Morman, Suzette A.; Neri, Antonio; Wolf, Ruth E.; Dooyema, Carrie A.; Hageman, Philip L.; Lowers, Heather; Fernette, Gregory L.; Meeker, Gregory P.; Benzel, William M.; Driscoll, Rhonda L.; Berry, Cyrus J.; Crock, James G.; Goldstein, Harland L.; Adams, Monique; Bartrem, Casey L.; Tirima, Simba; Behrooz, Behbod; von Lindern, Ian; Brown, Mary Jean

2013-01-01

Background: In 2010, Médecins Sans Frontières discovered a lead poisoning outbreak linked to artisanal gold processing in northwestern Nigeria. The outbreak has killed approximately 400 young children and affected thousands more. Objectives: Our aim was to undertake an interdisciplinary geological- and health-science assessment to clarify lead sources and exposure pathways, identify additional toxicants of concern and populations at risk, and examine potential for similar lead poisoning globally. Methods: We applied diverse analytical methods to ore samples, soil and sweep samples from villages and family compounds, and plant foodstuff samples. Results: Natural weathering of lead-rich gold ores before mining formed abundant, highly gastric-bioaccessible lead carbonates. The same fingerprint of lead minerals found in all sample types confirms that ore processing caused extreme contamination, with up to 185,000 ppm lead in soils/sweep samples and up to 145 ppm lead in plant foodstuffs. Incidental ingestion of soils via hand-to-mouth transmission and of dusts cleared from the respiratory tract is the dominant exposure pathway. Consumption of water and foodstuffs contaminated by the processing is likely lesser, but these are still significant exposure pathways. Although young children suffered the most immediate and severe consequences, results indicate that older children, adult workers, pregnant women, and breastfed infants are also at risk for lead poisoning. Mercury, arsenic, manganese, antimony, and crystalline silica exposures pose additional health threats. Conclusions: Results inform ongoing efforts in Nigeria to assess lead contamination and poisoning, treat victims, mitigate exposures, and remediate contamination. Ore deposit geology, pre-mining weathering, and burgeoning artisanal mining may combine to cause similar lead poisoning disasters elsewhere globally.

Gold deposits of the Carolina Slate Belt, southeastern United States--Age and origin of the major gold producers

USGS Publications Warehouse

Foley, Nora K.; Ayuso, Robert A.

2012-01-01

Gold- and iron sulfide-bearing deposits of the southeastern United States have distinctive mineralogical and geochemical features that provide a basis for constructing models of ore genesis for exploration and assessment of gold resources. The largest (historic) deposits, in approximate million ounces of gold (Moz Au), include those in the Haile (~ 4.2 Moz Au), Ridgeway (~1.5 Moz Au), Brewer (~0.25 Moz Au), and Barite Hill (0.6 Moz Au) mines. Host rocks are Late Proterozoic to early Paleozoic (~553 million years old) metaigneous and metasedimentary rocks of the Carolina Slate Belt that share a geologic affinity with the classic Avalonian tectonic zone. The inferred syngenetic and epithermal-subvolcanic quartz-porphyry settings occur stratigraphically between sequences of metavolcanic rocks of the Persimmon Fork and Uwharrie Formations and overlying volcanic and epiclastic rocks of the Tillery and Richtex Formations (and regional equivalents). The Carolina Slate Belt is highly prospective for many types of gold ore hosted within quartz-sericite-pyrite altered volcanic rocks, juvenile metasedimentary rocks, and in associated shear zones. For example, sheared and deformed auriferous volcanogenic massive sulfide deposits at Barite Hill, South Carolina, and in the Gold Hill trend, North Carolina, are hosted primarily by laminated mudstone and felsic volcanic to volcaniclastic rocks. The high-sulfidation epithermal style of gold mineralization at Brewer and low-sulfidation gold ores of the Champion pit at Haile occur in breccias associated with subvolcanic quartz porphyry and within crystal-rich tuffs, ash flows, and subvolcanic rhyolite. The Ridgeway and Haile deposits are primarily epithermal replacements and feeder zones within (now) metamorphosed crystal-rich tuffs, volcaniclastic sediments, and siltstones originally deposited in a marine volcanic-arc basinal setting. Recent discoveries in the region include (1) extensions of known deposits, such as at Haile where

Progress on geoenvironmental models for selected mineral deposit types, edited by R. R. Seal, II and N. K. Foley

USGS Publications Warehouse

Seal, Robert R.; Foley, Nora K.

2002-01-01

Since the beginning of economic geology as a subdiscipline of the geological sciences, economic geologists have tended to classify mineral deposits on the basis of geological, mineralogical, and geochemical criteria, in efforts to systematize our understanding of mineral deposits as an aid to exploration. These efforts have led to classifications based on commodity, geologic setting (Cox and Singer, 1986), inferred temperatures and pressures of ore formation (Lindgren, 1933), and genetic setting (Park and MacDiarmid, 1975; Jensen and Bateman, 1979). None of these classification schemes is mutually exclusive; instead, there is considerable overlap among all of these classifications. A natural outcome of efforts to classify mineral deposits is the development of “mineral deposit models.” A mineral deposit model is a systematically arranged body of information that describes some or all of the essential characteristics of a selected group of mineral deposits; it presents a concept within which essential attributes may be distinguished and from which extraneous, coincidental features may be recognized and excluded (Barton, 1993). Barton (1993) noted that the grouping of deposits on the basis of common characteristics forms the basis for a classification, but the specification of the characteristics required for belonging to the group is the basis for a model. Models range from purely descriptive to genetic. A genetic model is superior to a descriptive model because it provides a basis to distinguish essential from extraneous attributes, and it has flexibility to accommodate variability in sources, processes, and local controls. In general, a descriptive model is a necessary prerequisite to a genetic model.

Mercury contamination in agricultural soils from abandoned metal mines classified by geology and mineralization.

PubMed

Kim, Han Sik; Jung, Myung Chae

2012-01-01

This survey aimed to compare mercury concentrations in soils related to geology and mineralization types of mines. A total of 16,386 surface soils (0~15 cm in depth) were taken from agricultural lands near 343 abandoned mines (within 2 km from each mine) and analyzed for Hg by AAS with a hydride-generation device. To meaningfully compare mercury levels in soils with geology and mineralization types, three subclassification criteria were adapted: (1) five mineralization types, (2) four valuable ore mineral types, and (3) four parent rock types. The average concentration of Hg in all soils was 0.204 mg kg(-1) with a range of 0.002-24.07 mg kg(-1). Based on the mineralization types, average Hg concentrations (mg kg(-1)) in the soils decreased in the order of pegmatite (0.250) > hydrothermal vein (0.208) > hydrothermal replacement (0.166) > skarn (0.121) > sedimentary deposits (0.045). In terms of the valuable ore mineral types, the concentrations decreased in the order of Au-Ag-base metal mines ≈ base metal mines > Au-Ag mines > Sn-W-Mo-Fe-Mn mines. For parent rock types, similar concentrations were found in the soils derived from sedimentary rocks and metamorphic rocks followed by heterogeneous rocks with igneous and metamorphic processes. Furthermore, farmland soils contained relatively higher Hg levels than paddy soils. Therefore, it can be concluded that soils in Au, Ag, and base metal mines derived from a hydrothermal vein type of metamorphic rocks and pegmatite deposits contained relatively higher concentrations of mercury in the surface environment.

Geology and recognition criteria for uranium deposits of the quartz-pebble conglomerate type. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Button, A.; Adams, S.S.

1981-03-01

This report is concerned with Precambrian uraniferous conglomerates. This class of deposit has been estimated to contain between approximately 16 and 35 percent of the global uranium reserve in two rather small areas, one in Canada, the other in South Africa. Similar conglomerates, which are often gold-bearing, are, however, rather widespread, being found in parts of most Precambrian shield areas. Data have been synthesized on the geologic habitat and character of this deposit type. The primary objective has been to provide the most relevant geologic observations in a structural fashion to allow resource studies and exploration to focus on themore » most prospective targets in the shortest possible time.« less

Ordovician reef-hosted Jiaodingshan Mn-Co deposit and Dawashan Mn deposit, Sichuan Province, China

USGS Publications Warehouse

Fan, Delian; Hein, James R.; Ye, Jie

1999-01-01

The Jiaodingshan Mn-Co and Dawashan Mn deposits are located in the approximately 2-m thick Daduhe unit of the Wufengian strata of Late Ordovician (Ashgill) age. Paleogeographic reconstruction places the deposits at the time of their formation in a gulf between Chengdu submarine rise and the Kangdian continent. The Jiaodingshan and Dawashan deposits occur in algal-reef facies, the former in an atoll-like structure and the latter in a pinnacle reef. Ores are mainly composed of rhodochrosite, kutnahorite, hausmannite, braunite, manganosite, and bementite. Dark red, yellowish-pink, brown, green-gray, and black ores are massive, banded, laminated, spheroidal, and cryptalgal (oncolite, stromatolite, algal filaments) boundstones. Blue, green, and red algal fossils show in situ growth positions. Samples of high-grade Jiaodingshan and Dawashan ores assay as much as 66.7% MnO. Jiaodingshan Mn carbonate ores have mean contents of Ba, Co, and Pb somewhat higher than in Dawashan ores. Cobalt is widely distributed and strongly enriched in all rock types as compared to its crustal mean content. Cobalt is correlated with Cu, Ni, and MgO in both deposits and additionally with Ba and Zn in the Dawashan deposit. The δ13C(PDB) values of Mn carbonate ores (-7.8 to -16.3‰) indicate contributions of carbon from both seawater bicarbonate and the bacterial degradation of organic matter, the latter being 33% to 68%, assuming about -24‰ for the δ13C(PDB) of the organic matter. Host limestones derived carbon predominantly from seawater bicarbonate δ1313C(PDB) of +0.2 to -7‰). NW-trending fault zones controlled development of lithofacies, whereas NE-trending fault zones provided pathways for movement of fluids. The source of Co, Ni, and Cu was mainly from weathering of mafic and ultramafic rocks on the Kangdian continent, whereas contemporaneous volcanic eruptions were of secondary importance. The reefs were likely mineralized during early diagenesis under shallow burial. The reefs

Characterization of geologic deposits in the vicinity of US Ecology, Amargosa Basin, southern Nevada

USGS Publications Warehouse

Taylor, Emily M.

2010-01-01

Multiple approaches have been applied to better understand the characteristics of geologic units exposed at the surface and buried at depth in the vicinity of US Ecology (USE), a low-level commercial waste site in the northern Amargosa Desert, Nevada. Techniques include surficial geologic mapping and interpretation of the subsurface using borehole data. Dated deposits at depth were used to estimate rates of sediment accumulation. The subsurface lithologies have been modeled in three dimensions. Lithologic cross sections have been created from the three-dimensional model and have been compared to resistivity data at the same location. Where deposits appear offset, a fault was suspected. Global Positioning System elevation transects were measured and trenches were excavated to locate a strand of the Carrara Fault. The presence of the fault helps to better understand the shape of the potentiometric surface. These data will be used to better understand the hydrologic parameters controlling the containment of the waste at US Ecology.Quaternary geologic units exposed at the surface, in the vicinity of US Ecology, are derived from the alluvium shed off the adjacent range front and the Amargosa River. These deposits vary from modern to early Pleistocene in age. At depth, heterogeneous sands and gravel occur. Observed in deep trenches and boreholes, the subsurface deposits are characterized as fining-upward sequence of sediment from 5- to 8-meters thick. No volcanic units or fine-grained playa deposits were described in the boreholes to a depth of 200 meters. Based on Infrared Stimulated Luminescence dated core samples, short-term rates of sediment accumulation (<70,000 years) are an average of 2.7 millimeters per year, however, long-term rates (<3,900,000 years) are orders of magnitude less. Resistivity data, when compared to lithologic cross sections, generally are consistent with lithology grain size and probable soil carbonate accumulations. Surface resistivity displays

Using Copulas in the Estimation of the Economic Project Value in the Mining Industry, Including Geological Variability

NASA Astrophysics Data System (ADS)

Krysa, Zbigniew; Pactwa, Katarzyna; Wozniak, Justyna; Dudek, Michal

2017-12-01

Geological variability is one of the main factors that has an influence on the viability of mining investment projects and on the technical risk of geology projects. In the current scenario, analyses of economic viability of new extraction fields have been performed for the KGHM Polska Miedź S.A. underground copper mine at Fore Sudetic Monocline with the assumption of constant averaged content of useful elements. Research presented in this article is aimed at verifying the value of production from copper and silver ore for the same economic background with the use of variable cash flows resulting from the local variability of useful elements. Furthermore, the ore economic model is investigated for a significant difference in model value estimated with the use of linear correlation between useful elements content and the height of mine face, and the approach in which model parameters correlation is based upon the copula best matched information capacity criterion. The use of copula allows the simulation to take into account the multi variable dependencies at the same time, thereby giving a better reflection of the dependency structure, which linear correlation does not take into account. Calculation results of the economic model used for deposit value estimation indicate that the correlation between copper and silver estimated with the use of copula generates higher variation of possible project value, as compared to modelling correlation based upon linear correlation. Average deposit value remains unchanged.

Leach of the weathering crust elution-deposited rare earth ore for low environmental pollution with a combination of (NH4)2SO4 and EDTA.

PubMed

Tang, Jie; Qiao, Jiyang; Xue, Qiang; Liu, Fei; Chen, Honghan; Zhang, Guochen

2018-05-01

High concentration of ammonium sulfate, a typical leaching agent, was often used in the mining process of the weathering crust elution-deposited rare earth ore. After mining, a lot of ammonia nitrogen and labile heavy metal fractions were residual in tailings, which may result in a huge potential risk to the environment. In this study, in order to achieve the maximum extraction of rare earth elements and reduce the labile heavy metal, extraction effect and fraction changes of lanthanum (La) and lead (Pb) in the weathering crust elution-deposited rare earth ore were studied by using a compound agent of (NH 4 ) 2 SO 4 -EDTA. The extraction efficiency of La was more than 90% by using 0.2% (NH 4 ) 2 SO 4 -0.005 M EDTA, which was almost same with that by using 2.0% (NH 4 ) 2 SO 4 solution. In contrast, the extraction efficiency of Pb was 62.3% when use 0.2% (NH 4 ) 2 SO 4 -0.005 M EDTA, which is much higher than that (16.16%) achieved by using 2.0% (NH 4 ) 2 SO 4 solution. The released Pb fractions were mainly acid extractable and reducible fractions, and the content of reducible fraction being leached accounted for 70.45% of the total reducible fraction. Therefore, the use of 0.2% (NH 4 ) 2 SO 4 -0.005 M EDTA can not only reduce the amount of (NH 4 ) 2 SO 4 , but also decrease the labile heavy metal residues in soil, which provides a new way for efficient La extraction with effective preventing and controlling environmental pollution in the process of mining the weathering crust elution-deposited rare earth ore. Copyright © 2018 Elsevier Ltd. All rights reserved.

Porphyry copper deposit tract definition - A global analysis comparing geologic map scales

USGS Publications Warehouse

Raines, G.L.; Connors, K.A.; Chorlton, L.B.

2007-01-01

Geologic maps are a fundamental data source used to define mineral-resource potential tracts for the first step of a mineral resource assessment. Further, it is generally believed that the scale of the geologic map is a critical consideration. Previously published research has demonstrated that the U.S. Geological Survey porphyry tracts identified for the United States, which are based on 1:500,000-scale geology and larger scale data and published at 1:1,000,000 scale, can be approximated using a more generalized 1:2,500,000-scale geologic map. Comparison of the USGS porphyry tracts for the United States with weights-of-evidence models made using a 1:10,000,000-scale geologic map, which was made for petroleum applications, and a 1:35,000,000-scale geologic map, which was created as context for the distribution of porphyry deposits, demonstrates that, again, the USGS US porphyry tracts identified are similar to tracts defined on features from these small scale maps. In fact, the results using the 1:35,000,000-scale map show a slightly higher correlation with the USGS US tract definition, probably because the conceptual context for this small-scale map is more appropriate for porphyry tract definition than either of the other maps. This finding demonstrates that geologic maps are conceptual maps. The map information shown in each map is selected and generalized for the map to display the concepts deemed important for the map maker's purpose. Some geologic maps of small scale prove to be useful for regional mineral-resource tract definition, despite the decrease in spatial accuracy with decreasing scale. The utility of a particular geologic map for a particular application is critically dependent on the alignment of the intention of the map maker with the application. ?? International Association for Mathematical Geology 2007.

Textural, compositional, and sulfur isotope variations of sulfide minerals in the Red Dog Zn-Pb-Ag deposits, Brooks Range, Alaska: Implications for Ore Formation

USGS Publications Warehouse

Kelley, K.D.; Leach, D.L.; Johnson, C.A.; Clark, J.L.; Fayek, M.; Slack, J.F.; Anderson, V.M.; Ayuso, R.A.; Ridley, W.I.

2004-01-01

of yellow-brown sphalerite during subsea-floor hydrothermal recrystallization and coarsening of preexisting barite; (3) open-space deposition of barite, red-brown sphalerite and other sulfides in veins and coeval replacement of barite; and (4) postore sulfide deposition, including the formation of late tan sphalerite breccias. Stage 1 mineralization took place in a low-temperature environment where fluids rich in Ba mixed with pore water or water-column sulfate to form barite, and metals combined with H2S derived from bacterial sulfate reduction to form sulfides. Higher temperatures and salinities and relatively oxidized ore-stage fluids (stages 2 and 3) compared with stage 1 were probably important controls on the abundances and relative amounts of metals in the fluids and the resulting sulfide chemistry. Textural observations and isotopic data show that preexisting barite was reductively dissolved, providing a source of H2S for sulfide mineral formation. In stage 3, the continued flow of hydrothermal fluids caused thermal alteration of organic-rich mudstones and a build-up of methane that led to fluid overpressuring, hydrofracturing, and vein formation. Barite, red-brown sphalerite, and other sulfides were deposited in the veins, and preexisting barite was pervasively replaced by red-brown sphalerite. Hydrothermal activity ceased until Jurassic time when thrusting and large-scale fluid flow related to the Brookian orogeny remobilized and formed late tan sphalerite in tectonic breccias. ?? 2004 by Economic Geology.

Geochemical studies of rare earth elements in the Portuguese pyrite belt, and geologic and geochemical controls on gold distribution

USGS Publications Warehouse

Grimes, David J.; Earhart, Robert L.; de Carvalho, Delfim; Oliveira, Vitor; Oliveira, Jose T.; Castro, Paulo

1998-01-01

This report describes geochemical and geological studies which were conducted by the U.S. Geological Survey (USGS) and the Servicos Geologicos de Portugal (SPG) in the Portuguese pyrite belt (PPB) in southern Portugal. The studies included rare earth element (REE) distributions and geological and geochemical controls on the distribution of gold. Rare earth element distributions were determined in representative samples of the volcanic rocks from five west-trending sub-belts of the PPB in order to test the usefulness of REE as a tool for the correlation of volcanic events, and to determine their mobility and application as hydrothermal tracers. REE distributions in felsic volcanic rocks show increases in the relative abundances of heavy REE and a decrease in La/Yb ratios from north to south in the Portuguese pyrite belt. Anomalous amounts of gold are distributed in and near massive and disseminated sulfide deposits in the PPB. Gold is closely associated with copper in the middle and lower parts of the deposits. Weakly anomalous concentrations of gold were noted in exhalative sedimentary rocks that are stratigraphically above massive sulfide deposits in a distal manganiferous facies, whereas anomalously low concentrations were detected in the barite-rich, proximal-facies exhalites. Altered and pyritic felsic volcanic rocks locally contain highly anomalous concentrations of gold, suggesting that disseminated sulfide deposits and the non-ore parts of massive sulfide deposits should be evaluated for their gold potential.

Thallium-rich pyrite ores from the Apuan Alps, Tuscany, Italy:constraints for their origin and environmental concerns

NASA Astrophysics Data System (ADS)

D'Orazio, Massimo; Biagioni, Cristian; Dini, Andrea; Vezzoni, Simone

2017-06-01

The southern sector of the Apuan Alps (AA) massif, Tuscany, Italy, is characterized by the occurrence of a series of baryte-pyrite-iron oxide orebodies whose Tl-rich nature was recognized only recently. The geochemistry of the pyrite ore was investigated through inductively coupled plasma mass spectrometry. In addition, lead isotope data for selected pyrite ores from AA were collected. Pyrite ores are characterized by a complex geochemistry, with high concentrations of Tl (up to 1100 μg/g) coupled with high As and Sb contents; the Co/Ni ratio is always <1. Geochemical data of pyrite and marcasite ore samples from other mining districts of Tuscany have been collected in order to compare them with those from the AA. These samples usually have very low Tl content (less than 2 μg/g) and high to very high Co/Ni and As/Sb ratios. Only some samples from the Sb-Hg ore deposits showed very high Tl concentrations (up to 3900 μg/g). Another difference is related to the lead isotope composition, with pyrite ores from AA markedly less radiogenic than those from the other deposits from Tuscany. Geochemical data of pyrite ores from AA give new insights on the genesis of the baryte-pyrite-iron oxide orebodies, relating their formation to low-temperature hydrothermal systems active during early Paleozoic; in addition, these data play a fundamental role in assessing the environmental impact of these deposits.

The dilemma of the Jiaodong gold deposits: Are they unique?

USGS Publications Warehouse

Goldfarb, Richard J.; Santosh, M.

2013-01-01

The ca. 126–120 Ma Au deposits of the Jiaodong Peninsula, eastern China, define the country's largest gold province with an overall endowment estimated as >3000 t Au. The vein and disseminated ores are hosted by NE- to NNE-trending brittle normal faults that parallel the margins of ca. 165–150 Ma, deeply emplaced, lower crustal melt granites. The deposits are sited along the faults for many tens of kilometers and the larger orebodies are associated with dilatational jogs. Country rocks to the granites are Precambrian high-grade metamorphic rocks located on both sides of a Triassic suture between the North and South China blocks. During early Mesozoic convergent deformation, the ore-hosting structures developed as ductile thrust faults that were subsequently reactivated during Early Cretaceous “Yanshanian” intracontinental extensional deformation and associated gold formation.Classification of the gold deposits remains problematic. Many features resemble those typical of orogenic Au including the linear structural distribution of the deposits, mineralization style, ore and alteration assemblages, and ore fluid chemistry. However, Phanerozoic orogenic Au deposits are formed by prograde metamorphism of accreted oceanic rocks in Cordilleran-style orogens. The Jiaodong deposits, in contrast, formed within two Precambrian blocks approximately 2 billion years after devolatilization of the country rocks, and thus require a model that involves alternative fluid and metal sources for the ores. A widespread suite of ca. 130–123 Ma granodiorites overlaps temporally with the ores, but shows a poor spatial association with the deposits. Furthermore, the deposit distribution and mineralization style is atypical of ores formed from nearby magmas. The ore concentration requires fluid focusing during some type of sub-crustal thermal event, which could be broadly related to a combination of coeval lithospheric thinning, asthenospheric upwelling, paleo-Pacific plate

Porphyry-copper ore shells form at stable pressure-temperature fronts within dynamic fluid plumes.

PubMed

Weis, P; Driesner, T; Heinrich, C A

2012-12-21

Porphyry-type ore deposits are major resources of copper and gold, precipitated from fluids expelled by crustal magma chambers. The metals are typically concentrated in confined ore shells within vertically extensive vein networks, formed through hydraulic fracturing of rock by ascending fluids. Numerical modeling shows that dynamic permeability responses to magmatic fluid expulsion can stabilize a front of metal precipitation at the boundary between lithostatically pressured up-flow of hot magmatic fluids and hydrostatically pressured convection of cooler meteoric fluids. The balance between focused heat advection and lateral cooling controls the most important economic characteristics, including size, shape, and ore grade. This self-sustaining process may extend to epithermal gold deposits, venting at active volcanoes, and regions with the potential for geothermal energy production.

Porphyry-Copper Ore Shells Form at Stable Pressure-Temperature Fronts Within Dynamic Fluid Plumes

NASA Astrophysics Data System (ADS)

Weis, P.; Driesner, T.; Heinrich, C. A.

2012-12-01

Porphyry-type ore deposits are major resources of copper and gold, precipitated from fluids expelled by crustal magma chambers. The metals are typically concentrated in confined ore shells within vertically extensive vein networks, formed through hydraulic fracturing of rock by ascending fluids. Numerical modeling shows that dynamic permeability responses to magmatic fluid expulsion can stabilize a front of metal precipitation at the boundary between lithostatically pressured up-flow of hot magmatic fluids and hydrostatically pressured convection of cooler meteoric fluids. The balance between focused heat advection and lateral cooling controls the most important economic characteristics, including size, shape, and ore grade. This self-sustaining process may extend to epithermal gold deposits, venting at active volcanoes, and regions with the potential for geothermal energy production.

Technical Report on the Behavior of Trace Elements, Stable Isotopes, and Radiogenic Isotopes During the Processing of Uranium Ore to Uranium Ore Concentrate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marks, N. E.; Borg, L. E.; Eppich, G. R.

2015-07-09

The goals of this SP-1 effort were to understand how isotopic and elemental signatures behave during mining, milling, and concentration and to identify analytes that might preserve geologic signatures of the protolith ores. The impurities that are preserved through the concentration process could provide useful forensic signatures and perhaps prove diagnostic of sample origin.

ERTS-A data as a teaching and research tool in the Department of Geology

NASA Technical Reports Server (NTRS)

Grybeck, D. (Principal Investigator)

1973-01-01

The author has identified the following significant results. ERTS-1 prints have been used extensively in a geology of Alaska class to give a basic framework of the geology of the state. In addition, they have been intermittantly used in such diverse classes as: (1) Economic Geology (e.g. the Sn-bearing granites of the Seward Peninsula are particularly noticeable due to their wide contact metamorphic aureoles.) (2) A canned geology of Alaska lecture which has been given to two different introductory geology courses. (3) Structural Geology (e.g. the Fairweather and Denali faults are striking obvious). It was found most convenient for larger classes to prepare 35mm slides of the ERTS-1 prints that are used in conjunction with slides of the topographic and geologic maps at about the same scale. Thus the emphasis has been in integration of the ERTS-1 material into existing courses. As such, the ERTS-1 data has provided a unique and striking viewpoint that never fails to initiate favorable comment. In addition, prints have been examined by numerous researchers to develop a regional, integrated overview of such varied topics as regional geology to a background for local geologic mapping to studies of ore deposits and to the definition of a formation to be studied in detail at its type locality.

Magnetite-apatite mineralization in Khanlogh iron deposit, northwest of Neyshaboor, NE Iran

NASA Astrophysics Data System (ADS)

Najafzadeh Tehrani, Parvin; Asghar Calagari, Ali; Velasco Roldan, Francisco; Simmonds, Vartan; Siahcheshm, Kamal

2016-04-01

fluids. The high fluorine content of the apatite at Khanlogh may testify to the presence of Ti-fluoride complex in the fluids. Formation of apatite crystals was concurrent with development of titanium lamellae in magnetite. The apatite possesses high REE content which is possibly associated with monazite inclusions. The SEM studies better show these inclusions are occasionally present at the margin of apatite crystals and veins. Based upon field relations, microscopic examinations, and the results of XRD analyses, sodic (albite), propylitic (epidote, chlorite, calcite), and argillic (montmorillonite) alterations are developed in the study area. The principal minerals in these alteration zones are albite, epidote, sericite, chlorite, quartz, calcite, and montmorllonite. Mineralogy, alteration, geochemistry, structure, and texture of the ores at Khanlogh indicate that the magnetite and apatite were chiefly formed by hydrothermal solutions which were enriched in iron mainly transported by F- and Cl- rich fluids. Reference Hou,,T., Zhaochong, Z., Timothy, K., (2011). Gushan magnetite-apatite deposit in the Ningwu basin, Lower Yangtze River Valley, SE China: Hydrothermal or Kiruna-type? Ore geology review, 43, 333-346. Purtov, V.K., Kotelnikova, A.L. (1993). Solubility of titanium in chloride and fluoride hydrothermal solution. International Geology Review 35, 274 -287.

Matrix Effects Originating from Coexisting Minerals and Accurate Determination of Stable Silver Isotopes in Silver Deposits.

PubMed

Guo, Qi; Wei, Hai-Zhen; Jiang, Shao-Yong; Hohl, Simon; Lin, Yi-Bo; Wang, Yi-Jing; Li, Yin-Chuan

2017-12-19

Except for extensive studies in core formation and volatile-element depletion processes using radiogenic Ag isotopes (i.e., the Pd-Ag chronometer), recent research has revealed that the mass fractionation of silver isotopes is in principle controlled by physicochemical processes (e.g., evaporation, diffusion, chemical exchange, etc.) during magmatic emplacement and hydrothermal alteration. As these geologic processes only produce very minor variations of δ 109 Ag from -0.5 to +1.1‰, more accurate and precise measurements are required. In this work, a robust linear relationship between instrumental mass discrimination of Ag and Pd isotopes was obtained at the Ag/Pd molar ratio of 1:20. In Au-Ag ore deposits, silver minerals have complex paragenetic relationships with other minerals (e.g., chalcopyrite, sphalerite, galena, pyrite, etc.). It is difficult to remove such abundant impurities completely because the other metals are tens to thousands of times richer than silver. Both quantitative evaluation of matrix effects and modification of chemical chromatography were carried out to deal with the problems. Isobaric inferences (e.g., 65 Cu 40 Ar + to 105 Pd, 208 Pb 2+ to 104 Pd, and 67 Zn 40 Ar + to 107 Ag + ) and space charge effects dramatically shift the measured δ 109 Ag values. The selection of alternative Pd isotope pairs is effective in eliminating spectral matrix effects so as to ensure accurate analysis under the largest possible ranges for metal impurities, which are Cu/Ag ≤ 50:1, Fe/Ag ≤ 600:1, Pb/Ag ≤ 10:1, and Zn/Ag ≤ 1:1, respectively. With the modified procedure, we reported silver isotope compositions (δ 109 Ag) in geological standard materials and typical Au-Ag ore deposit samples varying from -0.029 to +0.689 ‰ with external reproducibility of ±0.009-0.084 ‰. A systemic survey of δ 109 Ag (or ε 109 Ag) variations in rocks, ore deposits, and environmental materials in nature is discussed.

Geology and mineral deposits of the Carlile quadrangle, Crook County, Wyoming

USGS Publications Warehouse

Bergendahl, M.H.; Davis, R.E.; Izett, G.A.

1961-01-01

thickness among all the Fall River units, with the exception of the upper unit. Petrographic studies on selected samples of units from both formations show differences in composition between Lakota and Fall River rocks.The Carlile quadrangle lies immediately east of the monocline that marks the outer limit of the Black Hills uplift, and the rocks in this area have a regional dip of less than 2° outward from the center of the uplift. Superimposed upon the regional uplift are many subordinate structural features anticlines, synclines, domes, basins, and terraces which locally modify the regional features. The most pronounced of these subordinate structural features are the doubly-plunging Pine Ridge, Oil Butte, and Dakota Divide anticlines, and the Eggie Creek syncline. Stress throughout the area was relieved almost entirely through folding; only a few small nearly vertical normal faults were found within the quadrangle.Uranium has been mined from the Carlile deposit, owned by the Homestake Mining Co. The ore minerals, carnotite and tyuyamnuite occur in a sandstone lens that is enclosed within relatively impermeable clayey beds in the mudstone unit of the Lakota formation. The ore also includes unidentified black vanadium minerals and possibly coffinite. Uranium minerals are more abundant in and adjacent to thicker carbonaceous and silty seams in the sandstone lens. A mixture of fine-grained calcium carbonate and calcium sulfate fills the interstices between detrital quartz grains in mineralized sandstone. Selenium and arsenic are more abundant in samples that are high in uranium. Drilling on Thorn Divide about 1 mile west of the Carlile mine has roughly outlined concentrations of a sooty black uranium mineral associated with pyrite In two stratigraphic intervals of the Lakota formation. One is in the same sandstone lens that contains the ore at the Carlile mine; the other is in conglomeratic sandstone near the base of the Lakota. These deposits are relatively deep, and no

New insight on the paleoproterozoic evolution of the São Francisco Craton: Reinterpretation of the geology, the suture zones and the thicknesses of the crustal blocks using geophysical and geological data

NASA Astrophysics Data System (ADS)

Sampaio, Edson E. S.; Barbosa, Johildo S. F.; Correa-Gomes, Luiz C.

2017-07-01

The Archean-Paleoproterozoic Jequié (JB) and Itabuna-Salvador-Curaçá (ISCB) blocks and their tectonic transition zone in the Valença region, Bahia, Brazil are potentially important for ore deposits, but the geological knowledge of the area is still meager. The paucity of geological information restricts the knowledge of the position and of the field characteristics of the tectonic suture zone between these two crustal segments JB and ISCB. Therefore, interpretation of geophysical data is necessary to supplement the regional structural and petrological knowledge of the area as well as to assist mining exploration programs. The analysis of the airborne radiometric and magnetic data of the region has established, respectively, five radiometric domains and five magnetic zones. Modeling of a gravity profile has defined the major density contrasts of the deep structures. The integrated interpretation of the geophysical data fitted to the known geological information substantially improved the suture zone (lower plate JB versus upper plate ISCB) delimitation, the geological map of the area and allowed to estimate the thicknesses of these two blocks, and raised key questions about the São Francisco Craton tectonic evolution.

Granite-related Yangjiashan tungsten deposit, southern China

NASA Astrophysics Data System (ADS)

Xie, Guiqing; Mao, Jingwen; Li, Wei; Fu, Bin; Zhang, Zhiyuan

2018-04-01

The Yangjiashan scheelite-bearing deposit (38,663 metric tons of WO3 with an average ore grade of 0.70% WO3) is hosted in quartz veins in a biotite monzogranite intrusion and surrounding slate in the Xiangzhong Metallogenic Province of southern China. The monzogranite has a zircon SHRIMP U-Pb age of 406.6 ± 2.8 Ma (2σ, n = 20, MSWD = 1.4). Cassiterite coexisting with scheelite yields a weighted mean 206Pb/238U age of 409.8 ± 5.9 Ma (2σ, n = 30, MSWD = 0.20), and molybdenite intergrown with scheelite yields a weighted mean Re-Os age of 404.2 ± 3.2 Ma (2σ, n = 3, MSWD = 0.10). These results suggest that the Yangjiashan tungsten deposit is temporally related to the Devonian intrusion. The δD and calculated δ18OH2O values of quartz intergrown with scheelite range from - 87 to - 68‰, and - 1.2 to 3.4‰, respectively. Sulfides have a narrow range of δ34S values of - 2.9 to - 0.7‰ with an average value of - 1.6‰ (n = 16). The integration of geological, stable isotope, and geochronological data, combined with the quartz-muscovite greisen style of ore, supports a magmatic-hydrothermal origin for the tungsten mineralization. Compared to the more common tungsten skarn, quartz-wolframite vein, and porphyry tungsten deposits, as well as orogenic gold deposits worldwide, the Yangjiashan tungsten deposit is an unusual example of a granite-related, gold-poor, scheelite-bearing quartz vein type of deposit. The calcium needed for the formation of scheelite is derived from the sericitization of calcic plagioclase in the monzogranite and Ca-bearing psammitic country rocks, and the relatively high pH, reduced and Ca-rich mineralizing fluid may be the main reasons for the formation of scheelite rather than wolframite at Yangjiashan.

The Myszkow porphyry copper-molybdenum deposit, Poland

USGS Publications Warehouse

Chaffee, M.A.; Eppinger, R.G.; Lason, K.; Slosarz, J.; Podemski, M.

1994-01-01

The porphyry copper-molybdenum deposit at Myszkow, south-central Poland, lies in the Cracow-Silesian orogenic belt, in the vicinity of a Paleozoic boundary between two tectonic plates. The deposit is hosted in a complex that includes early Paleozoic metasedimentary rocks intruded in the late Paleozoic by a predominantly granodioritic pluton. This deposit exhibits many features that are typical of porphyry copper deposits associated with calc-alkaline intrusive rocks, including ore- and alteration-mineral suites, zoning of ore and alteration minerals, fluid-inclusion chemistry, tectonic setting, and structural style of veining. Unusual features of the Myszkow deposit include high concentrations of tungsten and the late Paleozoic (Variscan) age. -Authors

In situ strontium and sulfur isotope investigation of the Ni-Cu-(PGE) sulfide ore-bearing Kevitsa intrusion, northern Finland

NASA Astrophysics Data System (ADS)

Luolavirta, Kirsi; Hanski, Eero; Maier, Wolfgang; Lahaye, Yann; O'Brien, Hugh; Santaguida, Frank

2018-01-01

The 2.06-Ga Kevitsa mafic-ultramafic intrusion in northern Finland hosts a large disseminated Ni-Cu-PGE deposit. The deposit occurs in the ultramafic olivine-pyroxene cumulates and shows a range in Ni tenors varying from 4-7 wt% (regular ore) to > 10 wt% (Ni-PGE ore). There are also a metal-poor sulfide mineralization (false ore) and contact mineralization that are uneconomic (Ni tenor < 4 wt%). The obtained 87Sr/86Sr(i) values of the Kevitsa ultramafic cumulates are highly radiogenic (> 0.7045) in comparison to the estimated depleted mantle Sr isotope ratio of 0.702 at 2.06 Ga. The sulfur δ 34S values are generally higher than + 2‰, which together with the Sr isotope data imply involvement of crustal material in the genesis of the Kevitsa intrusion and its ores. The 87Sr/86Sr(i) values obtained from the ore-bearing domain of the intrusion show stratigraphic variation and exceed 0.7050, with the maximum value reaching up to 0.7109. In contrast, in rocks around the ore domain, the initial Sr isotope compositions remain more or less constant (0.7047-0.7060) throughout the intrusive stratigraphy. The isotope data suggest that the ore-bearing domain of the intrusion represents a dynamic site with multiple injections of variably contaminated magma, whereas the surrounding part of the intrusion experienced a less vigorous emplacement history. No correlation is observed between the strontium and sulfur isotope compositions. This is explained by bulk assimilation of the silicate magma in a deeper staging magma chamber and variable assimilation of sulfur during magma transport into the Kevitsa magma chamber. The low level of metals in false ore and the Ni-depleted nature of its olivine suggest that some sulfides may have precipitated and deposited in the feeder conduit during the initial stage of magma emplacement. Cannibalization of early-formed sulfides by later magma injections may have been important in the formation of the economic ore deposit.

Radioactive rare-earth deposit at Scrub Oaks mine, Morris County, New Jersey

USGS Publications Warehouse

Klemic, Harry; Heyl, A.V.; Taylor, Audrey R.; Stone, Jerome

1959-01-01

A deposit of rare-earth minerals in the Scrub Oaks iron mine, Morris County, N. J., was mapped and sampled in 1955. The rare-earth minerals are mainly in coarse-grained magnetite ore and in pegmatite adjacent to it. Discrete bodies of rare-earth-bearing magnetite ore apparently follow the plunge of the main magnetite ore body at the north end of the mine. Radioactivity of the ore containing rare earths is about 0.2 to 0.6 mllliroentgens per hour. The principal minerals of the deposit are quartz, magnetite, hematite, albiteoligoclase, perthite and antiperthite. Xenotime and doverite aggregates and bastnaesite with intermixed leucoxene are the most abundant rare-earth minerals, and zircon, sphene, chevkinite, apatite, and monazite are of minor abundance in the ore. The rare-earth elements are partly differentiated into cerium-rich bastnaesite, chevkinite, and monazite, and yttrium-rich xenotime and doverite. Apatite, zircon, and sphene contain both cerium and yttrium group earths. Eleven samples of radioactive ore and rock average 0.009 percent uranium, 0.062 percent thorium, 1.51 percent combined rare-earth oxides including yttrium oxide and 24.8 percent iron. Scatter diagrams of sample data show a direct correlation between equivalent uranium, uranium, thorium, and combined rare^ earth oxides. Both cerium- and yttrium-group earths are abundant in the rare-earth minerals. Radioactive magnetite ore containing rare-earth minerals probably formed as a variant of the magnetite mineralization that produced the main iron ore of the Scrub Oaks deposit. The rare-earth minerals and the iron ore were deposited contemporaneously. Zircon crystals, probably deposited at the same time, have been determined by the Larsen method to be about 550 to 600 million years old (late Precambrian age). Uranium, thorium, and rare-earth elements are potential byproducts of iron in the coarse-grained magnetite ore.

Modeling the formation of porphyry-copper ores

USGS Publications Warehouse

Ingebritsen, Steven E.

2012-01-01

Porphyry-copper ore systems, the source of much of the world's copper and molybdenum, form when metal-bearing fluids are expelled from shallow, degassing magmas. On page 1613 of this issue, Weis et al. (1) demonstrate that self-organizing processes focus metal deposition. Specifically, their simulation studies indicate that ores develop as consequences of dynamic variations in rock permeability driven by injection of volatile species from rising magmas. Scenarios with a static permeability structure could not reproduce key field observations, whereas dynamic permeability responses to magmatic-fluid injection localized a metal-precipitation front where enrichment by a factor of 103 could be achieved [for an overview of their numerical-simulation model CSMP++, see (2)].

Comparison of the mineralogy of the Boss-Bixby, Missouri copper-iron deposit, and the Olympic Dam copper-uranium-gold deposit, South Australia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brandom, R.T.; Hagni, R.D.; Allen, C.R.

1985-01-01

An ore microscopic examination of 80 polished sections prepared from selected drill core specimens from the Boss-Bixby, Missouri copper-iron deposit has shown that its mineral assemblage is similar to that of the Olympic Dam (Roxby Downs) copper-uranium-gold deposit in South Australia. A comparison with the mineralogy reported for Olympic Dam shows that both deposits contain: 1) the principal minerals, magnetite, hematite, chalcopyrite, and bornite, 2) the cobalt-bearing phases, carrollite and cobaltian pyrite, 3) the titanium oxides, rutile and anatase, 4) smaller amounts of martite, covellite, and electrum, 5) fluorite and carbonates, and 6) some alteration minerals. The deposits also aremore » similar with regard to the sequence of mineral deposition: 1) early oxides, 2) then sulfide minerals, and 3) a final oxide generation. The deposits, however, are dissimilar with regard to their host rock lithologies and structural settings. The Boss-Bixby ores occupy breccia zones within a hydrothermally altered basic intrusive and intruded silicic volcanics, whereas the Olympic Dam ores are contained in sedimentary breccias in a graben or trough. Also, some minerals have been found thus far to occur at only one of the deposits. The similarity of mineralogy in these deposits suggests that they were formed from ore fluids that had some similarities in character and that the St. Francois terrane of Missouri is an important region for further exploration for deposits with this mineral assemblage.« less

A geochemical assessment of possible lunar ore formation

NASA Technical Reports Server (NTRS)

Haskin, Larry A.; Colson, Russell O.; Vaniman, David

1991-01-01

The Moon apparently formed without appreciable water or other relatively volatile materials. Interior concentrations of water or other volatile substances appear to be extremely low. On Earth, water is important to the genesis of nearly all types of ores. Thus, some have reasoned that only abundant elements would occur in ore concentrations. The definition and recognition of ores on the Moon challenge the imaginations and the terrestrial perceptions of ore bodies. Lunar ores included solar-wind soaked soils, which contain abundant but dilute H, C, N, and noble gases (including He-3). Oxygen must be mined; soils contain approximately 45 percent (wt). Mainstream processes of rock formation concentrated Si, Mg, Al, Fe, and Ca, and possibly Ti and Cr. The highland surface contains approximately 70 percent (wt) feldspar (mainly CaAl2Si2O8), which can be separated from some highland soils. Small fragments of dunite were collected; dunite may occur in walls and central peaks of some craters. Theoretical extensions of observations of lunar samples suggest that the Moon may have produced ores of trace elements. Some small fragments have trace-element concentrations 10(exp 4) times higher than the lunar average, indicating that effective geochemical separations occurred; processes included fractional crystallization, silicate immiscibility, vaporization and condensation, and sulfide metamorphism. Operations of these processes acting on indigenous materials and on meteoritic material in the regolith could have produced ores. Infalling carbonaceous meteorites and comets have added water and hydrocarbons that may have been cold-trapped. Vesicles in basalts, pyroclastic beads, and reported transient events suggest gag emission from the lunar interior; such gas might concentrate and transport rare elements. Large impacts may disperse ores or produce them through deposition of heat at depth and by vaporization and subsequent condensation. The main problem in assessing lunar