Science.gov

Sample records for ii simultaneous addition

  1. H-point standard addition method for simultaneous spectrophotometric determination of Co(II) and Ni(II) by 1-(2-pyridylazo)2-naphthol in micellar media.

    PubMed

    Afkhami, Abbas; Bahram, Morteza

    2004-01-01

    A very simple and selective spectrophotometric method for simultaneous determination of Co(II) and Ni(II) by 1-(2-pyridylazo) 2-naphthol (PAN), in micellar media, using H-point standard addition method (HPSAM) is described. The ligand and its metal complexes (Co(II)-PAN and Ni(II)-PAN) were made water-soluble by the neutral surfactant Triton X-100, and therefore, no extraction with organic solvents was required. Formation of both the complexes was complete within 10 min at pH 9 (adjusted by ammonia buffer). The linear range was 0.10-2.00 microg ml(-1) for Co(II) and 0.05-1.50 microg ml(-1) for Ni(II). The relative standard deviation (R.S.D.) for the simultaneous determination of 0.50 microg ml(-1) each of Co(II) and Ni(II) was 2.32 and 3.13%, respectively. Interference effects of common anions and cations were studied and the method was applied to simultaneous determination of Co(II) and Ni(II) in alloy samples. The method was compared with derivative spectrophotometric method. PMID:14670476

  2. Shaping frequency response of a vibrating plate for passive and active control applications by simultaneous optimization of arrangement of additional masses and ribs. Part II: Optimization

    NASA Astrophysics Data System (ADS)

    Wrona, Stanislaw; Pawelczyk, Marek

    2016-03-01

    It was shown in Part I that an ability to shape frequency response of a vibrating plate according to precisely defined demands has a very high practical potential. It can be used to improve acoustic radiation of the plate for required frequencies or enhance acoustic isolation of noise barriers and device casings. It can be used for both passive and active control. The proposed method is based on mounting several additional ribs and masses (passive and/or active) to the plate surface at locations followed from an optimisation process. In Part I a relevant model of such structure, as a function of arrangement of the additional elements was derived and validated. The model allows calculating natural frequencies and mode-shapes of the whole structure. The aim of this companion paper, Part II, is to present the second stage of the method. This is an optimization process that results in arrangement of the elements guaranteeing desired plate frequency response, and enhancement of controllability and observability measures. For that purpose appropriate cost functions, and constraints followed from technological feasibility are defined. Then, a memetic algorithm is employed to obtain a numerical solution with parameters of the arrangement. The optimization results are initially presented for simple cases to validate the method. Then, more complex scenarios are analysed with very special demands concerning the frequency response to present the full potential of the method. Subsequently, a laboratory experiment is presented and discussed. Finally, other areas of applications of the proposed method are shown and conclusions for future research are drawn.

  3. AGNs with composite spectra. II. Additional data

    NASA Astrophysics Data System (ADS)

    Gonçalves, A. C.; Véron-Cetty, M.-P.; Véron, P.

    1999-03-01

    In a previous paper \\cite[(Véron et al. 1997)]{ver97} we presented medium resolution (3.4 Angstroms FWHM) spectroscopic observations of 15 ``transition objects'', selected for having an ambiguous location in the \\cite[Veilleux & Osterbrock (1987)]{vei87} diagnostic diagrams, and showed that most of them were in fact ``composite'', this being due to the simultaneous presence on the slit of both a Seyfert or Liner nucleus and a H Ii region. Here, we report new spectroscopic observations of 53 emission-line galaxies with a ``transition'' spectrum, bringing up to 61 the total number of observed objects in an unbiased sample of 88 ``transition objects''. Almost all of the observed galaxies have a ``composite" nature, confirming the finding that true ``transition'' spectra may not exist at all. By eliminating ``composite objects'' from the diagnostic diagrams, a clear separation between the different classes of nuclear emission-line regions (Seyfert 2s, Liners and H Ii regions) becomes apparent; by restricting the volume occupied by the different line-emitting regions in the 3-dimensional diagnostic diagrams, we are also restricting the range of possible physical parameters in these regions. There seems to be no continuity between Seyfert 2s and Liners, the two classes occupying distinct volumes in the 3-dimensional space defined by lambda 6300/Hα ii, lambda 6583/Hα , and lambda 6300/Hα . Based on observations collected at the Observatoire de Haute-Provence (CNRS), France, and Hubble Space Telescope (HST) data obtained from the Space Telescope European Coordinating Facility (ST-ECF) archive. Tables 5 and 6 are also available in electronic form at the CDS via anonymous ftp to cdsarc.u-strasbg.fr (130.79.128.5) or via http://cdsweb.u-strasbg.fr/Abstract.html

  4. Sensitive electrochemical sensor using a graphene-polyaniline nanocomposite for simultaneous detection of Zn(II), Cd(II), and Pb(II).

    PubMed

    Ruecha, Nipapan; Rodthongkum, Nadnudda; Cate, David M; Volckens, John; Chailapakul, Orawon; Henry, Charles S

    2015-05-18

    This work describes the development of an electrochemical sensor for simultaneous detection of Zn(II), Cd(II), and Pb(II) using a graphene-polyaniline (G/PANI) nanocomposite electrode prepared by reverse-phase polymerization in the presence of polyvinylpyrrolidone (PVP). Two substrate materials (plastic film and filter paper) and two nanocomposite deposition methods (drop-casting and electrospraying) were investigated. Square-wave anodic stripping voltammetry currents were higher for plastic vs. paper substrates. Performance of the G/PANI nanocomposites was characterized by scanning electron microscopy (SEM) and cyclic voltammetry. The G/PANI-modified electrode exhibited high electrochemical conductivity, producing a three-fold increase in anodic peak current (vs. the unmodified electrode). The G/PANI-modified electrode also showed evidence of increased surface area under SEM. Square-wave anodic stripping voltammetry was used to measure Zn(II), Cd(II), and Pb(II) in the presence of Bi(III). A linear working range of 1-300 μg L(-1) was established between anodic current and metal ion concentration with detection limits (S/N=3) of 1.0 μg L(-1) for Zn(II), and 0.1 μg L(-1) for both Cd(II) and Pb(II). The G/PANI-modified electrode allowed selective determination of the target metals in the presence of common metal interferences including Mn(II), Cu(II), Fe(III), Fe(II), Co(III), and Ni(II). Repeat assays on the same device demonstrated good reproducibility (%RSD<11) over 10 serial runs. Finally, this system was utilized for determining Zn(II), Cd(II), and Pb(II) in human serum using the standard addition method. PMID:25910444

  5. H-point standard additions method for simultaneous determination of sulfamethoxazole and trimethoprim in pharmaceutical formulations and biological fluids with simultaneous addition of two analytes

    NASA Astrophysics Data System (ADS)

    Givianrad, M. H.; Saber-Tehrani, M.; Aberoomand-Azar, P.; Mohagheghian, M.

    2011-03-01

    The applicability of H-point standard additions method (HPSAM) to the resolving of overlapping spectra corresponding to the sulfamethoxazole and trimethoprim is verified by UV-vis spectrophotometry. The results show that the H-point standard additions method with simultaneous addition of both analytes is suitable for the simultaneous determination of sulfamethoxazole and trimethoprim in aqueous media. The results of applying the H-point standard additions method showed that the two drugs could be determined simultaneously with the concentration ratios of sulfamethoxazole to trimethoprim varying from 1:18 to 16:1 in the mixed samples. Also, the limits of detections were 0.58 and 0.37 μmol L -1 for sulfamethoxazole and trimethoprim, respectively. In addition the means of the calculated RSD (%) were 1.63 and 2.01 for SMX and TMP, respectively in synthetic mixtures. The proposed method has been successfully applied to the simultaneous determination of sulfamethoxazole and trimethoprim in some synthetic, pharmaceutical formulation and biological fluid samples.

  6. Simultaneous Femtosecond X-ray Spectroscopy and Diffraction of Photosystem II at Room Temperature

    PubMed Central

    Kern, Jan; Alonso-Mori, Roberto; Tran, Rosalie; Hattne, Johan; Gildea, Richard J.; Echols, Nathaniel; Glöckner, Carina; Hellmich, Julia; Laksmono, Hartawan; Sierra, Raymond G.; Lassalle-Kaiser, Benedikt; Koroidov, Sergey; Lampe, Alyssa; Han, Guangye; Gul, Sheraz; DiFiore, Dörte; Milathianaki, Despina; Fry, Alan R.; Miahnahri, Alan; Schafer, Donald W.; Messerschmidt, Marc; Seibert, M. Marvin; Koglin, Jason E.; Sokaras, Dimosthenis; Weng, Tsu-Chien; Sellberg, Jonas; Latimer, Matthew J.; Grosse-Kunstleve, Ralf W.; Zwart, Petrus H.; White, William E.; Glatzel, Pieter; Adams, Paul D.; Bogan, Michael J.; Williams, Garth J.; Boutet, Sébastien; Messinger, Johannes; Zouni, Athina; Sauter, Nicholas K.; Yachandra, Vittal K.; Bergmann, Uwe; Yano, Junko

    2013-01-01

    Intense femtosecond X-ray pulses produced at the Linac Coherent Light Source (LCLS) were used for simultaneous X-ray diffraction (XRD) and X-ray emission spectroscopy (XES) of microcrystals of Photosystem II (PS II) at room temperature. This method probes the overall protein structure and the electronic structure of the Mn4CaO5 cluster in the oxygen-evolving complex of PS II. XRD data are presented from both the dark state (S1) and the first illuminated state (S2) of PS II. Our simultaneous XRD/XES study shows that the PS II crystals are intact during our measurements at the LCLS, not only with respect to the structure of PS II, but also with regard to the electronic structure of the highly radiation sensitive Mn4CaO5 cluster, opening new directions for future dynamics studies. PMID:23413188

  7. [Simultaneous determination of six food additives in meat products by high performance liquid chromatography].

    PubMed

    Li, Xiuqin; Zhang, Qinghe; Yang, Zong

    2010-12-01

    A novel method was proposed for the simultaneous separation and determination of six food additives, benzoic acid, sorbic acid, saccharin sodium, acesulfame potassium, ponceau 4R and allura red AC, by high performance liquid chromatography (HPLC). After optimized the separation conditions of HPLC, the separation can be completed within 18 min by using a ZORBAX Eclipse Plus C18 column (150 mm x 4.6 mm, 5 microm) with 20 mmol/L ammonium acetate (pH 6.9) and methanol as the mobile phases. The gradient elution was performed by 8% methanol (0-2 min), 8%-50% methanol (2-3 min), 50% methanol (3-9 min), 50%-8% methanol (9-12 min) and 8% methanol (12-18 min). The detection wavelength was set at 235 nm. This method has been successfully applied to the analysis of meat products and the average recoveries ranged from 80.7% to 94.4% at high and low spiked levels. The relative standard deviations (RSDs, n=3) were between 2.0% and 7.1%. The method is simple, rapid, accurate and suitable for the simultaneous determination of the six food additives in meat products. PMID:21438379

  8. Simultaneous determination of iron (II) and ascorbic acid in pharmaceuticas based on flow sandwich technique.

    PubMed

    Vakh, Christina; Freze, Elena; Pochivalov, Alexsey; Evdokimova, Ekaterina; Kamencev, Mihail; Moskvin, Leonid; Bulatov, Andrey

    2015-01-01

    The simple and easy performed flow system based on sandwich technique has been developed for the simultaneous separate determination of iron (II) and ascorbic acid in pharmaceuticals. The implementation of sandwich technique assumed the injection of sample solution between two selective reagents and allowed the carrying out in reaction coil two chemical reactions simultaneously: iron (II) with 1,10-phenanthroline and ascorbic acid with sodium 2,6-dichlorophenolindophenol. For achieving of excellent repeatability and considerable reagent saving the various parameters such as flow rate, sample and reagent volumes, reaction coil length were also optimized. The limits of detection (LODs) obtained by using the developed flow sandwich-type approach were 0.2 mg L(-1) for iron (II) and 0.7 mg L(-1) for ascorbic acid. The suggested approach was validated according to the following parameters: linearity and sensitivity, precision, recoveries and accuracy. The sampling frequency was 41 h(-1). PMID:25862995

  9. Simultaneous determination of Fluticasone propionate and Azelastine hydrochloride in the presence of pharmaceutical dosage form additives

    NASA Astrophysics Data System (ADS)

    Merey, Hanan A.; El-Mosallamy, Sally S.; Hassan, Nagiba Y.; El-Zeany, Badr A.

    2016-05-01

    Fluticasone propionate (FLU) and Azelastine hydrochloride (AZE) are co-formulated with phenylethyl alcohol (PEA) and Benzalkonium chloride (BENZ) (as preservatives) in pharmaceutical dosage form for treatment of seasonal allergies. Different spectrophotometric methods were used for the simultaneous determination of cited drugs in the dosage form. Direct spectrophotometric method was used for determining of AZE, while Derivative of double divisor of ratio spectra (DD-RS), Ratio subtraction coupled with ratio difference method (RS-RD) and Mean centering of the ratio spectra (MCR) are used for the determination of FLU. The linearity of the proposed methods was investigated in the range of 5.00-40.00 and 5.00-80.00 μg/mL for FLU and AZE, respectively. The specificity of the developed methods was investigated by analyzing laboratory prepared mixtures containing different ratios of cited drugs in addition to PEA and their pharmaceutical dosage form. The validity of the proposed methods was assessed using the standard addition technique. The obtained results were statistically compared with those obtained by official or the reported method for FLU or AZE, respectively showing no significant difference with respect to accuracy and precision at p = 0.05.

  10. Simultaneous determination of Fluticasone propionate and Azelastine hydrochloride in the presence of pharmaceutical dosage form additives.

    PubMed

    Merey, Hanan A; El-Mosallamy, Sally S; Hassan, Nagiba Y; El-Zeany, Badr A

    2016-05-01

    Fluticasone propionate (FLU) and Azelastine hydrochloride (AZE) are co-formulated with phenylethyl alcohol (PEA) and Benzalkonium chloride (BENZ) (as preservatives) in pharmaceutical dosage form for treatment of seasonal allergies. Different spectrophotometric methods were used for the simultaneous determination of cited drugs in the dosage form. Direct spectrophotometric method was used for determining of AZE, while Derivative of double divisor of ratio spectra (DD-RS), Ratio subtraction coupled with ratio difference method (RS-RD) and Mean centering of the ratio spectra (MCR) are used for the determination of FLU. The linearity of the proposed methods was investigated in the range of 5.00-40.00 and 5.00-80.00μg/mL for FLU and AZE, respectively. The specificity of the developed methods was investigated by analyzing laboratory prepared mixtures containing different ratios of cited drugs in addition to PEA and their pharmaceutical dosage form. The validity of the proposed methods was assessed using the standard addition technique. The obtained results were statistically compared with those obtained by official or the reported method for FLU or AZE, respectively showing no significant difference with respect to accuracy and precision at p=0.05. PMID:26921606

  11. [Simultaneous determination of various food additives by high performance liquid chromatography].

    PubMed

    Chen, Q C; Yu, W L; Wang, J

    2001-03-01

    A novel method is proposed for the simultaneous separation and determination of eight food additives, acesulfame potassium (AK), aspartame (ASP), benzoic acid (BA), caffeine (CA), saccharin sodium (SA), sorbic acid (SOR), theobromine (TB) and theophylline (TP) by reversed-phase high performance liquid chromatography. The separation was achieved within 23 min by using an Alltech Econosphere C18 column with 10 mmol/L NaH2PO4(pH 4.00)-acetonitrile (90:10, V/V) as mobile phase. The qualification and quantitation were accomplished by using a photodiode array detector. The detection limits (S/N = 3) for all analytes were below mg/L level. Under the experimental conditions, other common food additives and organic acids such as cyclamate, citric acid, malic acid, tartaric acid and ascorbic acid, did not interfere with the determination. The method has been successfully applied to the analysis of various foods as well as pharmaceutical preparation, and the average recoveries for real samples ranged from 78.5% to 107.2%. PMID:12541649

  12. Phase II Study of Preoperative Helical Tomotherapy With a Simultaneous Integrated Boost for Rectal Cancer

    SciTech Connect

    Engels, Benedikt; Tournel, Koen; Everaert, Hendrik; Hoorens, Anne; Sermeus, Alexandra; Christian, Nicolas; Storme, Guy; Verellen, Dirk; De Ridder, Mark

    2012-05-01

    Purpose: The addition of concomitant chemotherapy to preoperative radiotherapy is considered the standard of care for patients with cT3-4 rectal cancer. The combined treatment modality increases the complete response rate and local control (LC), but has no impact on survival or the incidence of distant metastases. In addition, it is associated with considerable toxicity. As an alternative strategy, we explored prospectively, preoperative helical tomotherapy with a simultaneous integrated boost (SIB). Methods and Materials: A total of 108 patients were treated with intensity-modulated and image-guided radiotherapy using the Tomotherapy Hi-Art II system. A dose of 46 Gy, in daily fractions of 2 Gy, was delivered to the mesorectum and draining lymph nodes, without concomitant chemotherapy. Patients with an anticipated circumferential resection margin (CRM) of less than 2 mm, based on magnetic resonance imaging, received a SIB to the tumor up to a total dose of 55.2 Gy. Acute and late side effects were scored using the National Cancer Institute Common Terminology Criteria for Adverse Events version 3.0. Results: A total of 102 patients presented with cT3-4 tumors; 57 patients entered the boost group and 51 the no-boost group. One patient in the no-boost group developed a radio-hypersensitivity reaction, resulting in a complete tumor remission, a Grade 3 acute and Grade 5 late enteritis. No other Grade {>=}3 acute toxicities occurred. With a median follow-up of 32 months, Grade {>=}3 late gastrointestinal and urinary toxicity were observed in 6% and 4% of the patients, respectively. The actuarial 2-year LC, progression-free survival and overall survival were 98%, 79%, and 93%. Conclusions: Preoperative helical tomotherapy displays a favorable acute toxicity profile in patients with cT3-4 rectal cancer. A SIB can be safely administered in patients with a narrow CRM and resulted in a promising LC.

  13. Simultaneous Estimation of Additive and Mutational Genetic Variance in an Outbred Population of Drosophila serrata.

    PubMed

    McGuigan, Katrina; Aguirre, J David; Blows, Mark W

    2015-11-01

    How new mutations contribute to genetic variation is a key question in biology. Although the evolutionary fate of an allele is largely determined by its heterozygous effect, most estimates of mutational variance and mutational effects derive from highly inbred lines, where new mutations are present in homozygous form. In an attempt to overcome this limitation, middle-class neighborhood (MCN) experiments have been used to assess the fitness effect of new mutations in heterozygous form. However, because MCN populations harbor substantial standing genetic variance, estimates of mutational variance have not typically been available from such experiments. Here we employ a modification of the animal model to analyze data from 22 generations of Drosophila serrata bred in an MCN design. Mutational heritability, measured for eight cuticular hydrocarbons, 10 wing-shape traits, and wing size in this outbred genetic background, ranged from 0.0006 to 0.006 (with one exception), a similar range to that reported from studies employing inbred lines. Simultaneously partitioning the additive and mutational variance in the same outbred population allowed us to quantitatively test the ability of mutation-selection balance models to explain the observed levels of additive and mutational genetic variance. The Gaussian allelic approximation and house-of-cards models, which assume real stabilizing selection on single traits, both overestimated the genetic variance maintained at equilibrium, but the house-of-cards model was a closer fit to the data. This analytical approach has the potential to be broadly applied, expanding our understanding of the dynamics of genetic variance in natural populations. PMID:26384357

  14. [Simultaneous determination of platinum (IV) and palladium (II) using spectrophotometry method].

    PubMed

    Ma, Dong-Lan; Wang, Yun; Ma, Kuang-Biao; Wang, Jin-Ye

    2009-10-01

    The N-(m-methylphenyl)-N'-(sodium p-aminobenzenesulfonate)-thiourea (MMPT) was good reagent of water solubility. In the medium of an HAc-NaAc buffer solution and hexadecyltrimethylammonium bromide (CTMAB), MMPT can react with platinum (IV) and palladium (II) to form green and brown soluble complex. The maximum absorbance of the complex was at lambdaPt(max) = 754.4 nm and lambdaPD(max) = 304.6 nm. Beer's law was obeyed with the concentration in the range of 0-32.0 microg Pt(IV)/25 mL and 0-25.0 microg Pd(II)/25 mL for platinum (IV) and palladium(II) respectively. The correlated coefficient was r754.4 = 0.999 5 for platinum (IV); and r304.6 = 0.999 9 for palladium (II). Their molar absorption coefficients were epsilonPT(754.4 = 8.6 x 10(4) L x mol(-1) x cm(-1) and epsilonPd(304.6) = 7.4 x 10(4) L x mol(-1) x cm(-1) respectively. The contents of platinum (IV) and palladium (II) were converted by determination of the absorbency of mix solution of platinum (IV) and palladium (II) at 754.4 and 304.6 nm. Only Cu2+ and Co2+ interfered with the determination of palladium (II) among 50 coexistent ions, so the selectivity was good. It can be used for the determination of content of synthesis samples. The relative standard deviation (RSD) was less than 2.0%, and the recovery (%) was in the range of 96%-104%. The results are satisfactory. Because the reagent reacts with platinum (IV) and palladium (II) to form water soluble complex and does not require pre-separation for simultaneous determination of platinum (IV) and palladium (II), the method is easy to operate, rapid and environment-friendly. PMID:20038071

  15. Insulin receptor isoform A and insulin-like growth factor II as additional treatment targets in human osteosarcoma.

    PubMed

    Avnet, Sofia; Sciacca, Laura; Salerno, Manuela; Gancitano, Giovanni; Cassarino, Maria Francesca; Longhi, Alessandra; Zakikhani, Mahvash; Carboni, Joan M; Gottardis, Marco; Giunti, Armando; Pollak, Michael; Vigneri, Riccardo; Baldini, Nicola

    2009-03-15

    Despite the frequent presence of an insulin-like growth factor I receptor (IGFIR)-mediated autocrine loop in osteosarcoma (OS), interfering with this target was only moderately effective in preclinical studies. Here, we considered other members of the IGF system that might be involved in the molecular pathology of OS. We found that, among 45 patients with OS, IGF-I and IGFBP-3 serum levels were significantly lower, and IGF-II serum levels significantly higher, than healthy controls. Increased IGF-II values were associated with a decreased disease-free survival. After tumor removal, both IGF-I and IGF-II levels returned to normal values. In 23 of 45 patients, we obtained tissue specimens and found that all expressed high mRNA level of IGF-II and >IGF-I. Also, isoform A of the insulin receptor (IR-A) was expressed at high level in addition to IGFIR and IR-A/IGFIR hybrids receptors (HR(A)). These receptors were also expressed in OS cell lines, and simultaneous impairment of IGFIR, IR, and Hybrid-Rs by monoclonal antibodies, siRNA, or the tyrosine kinase inhibitor BMS-536924, which blocks both IGFIR and IR, was more effective than selective anti-IGFIR strategies. Also, anti-IGF-II-siRNA treatment in low-serum conditions significantly inhibited MG-63 OS cells that have an autocrine circuit for IGF-II. In summary, IGF-II rather than IGF-I is the predominant growth factor produced by OS cells, and three different receptors (IR-A, HR(A), and IGFIR) act complementarily for an IGF-II-mediated constitutive autocrine loop, in addition to the previously shown IGFIR/IGF-I circuit. Cotargeting IGFIR and IR-A is more effective than targeting IGF-IR alone in inhibiting OS growth. PMID:19258511

  16. STATISTICAL PROPERTIES OF THE DISK COUNTERPARTS OF TYPE II SPICULES FROM SIMULTANEOUS OBSERVATIONS OF RAPID BLUESHIFTED EXCURSIONS IN Ca II 8542 AND H{alpha}

    SciTech Connect

    Sekse, D. H.; Rouppe van der Voort, L.; De Pontieu, B.

    2012-06-20

    Spicules were recently found to exist as two different types when a new class of so-called type II spicules was discovered at the solar limb with the Solar Optical Telescope on board the Hinode spacecraft. These type II spicules have been linked with on-disk observations of rapid blueshifted excursions (RBEs) in the H{alpha} and Ca II 8542 lines. Here we analyze observations optimized for the detection of RBEs in both H{alpha} and Ca II 8542 lines simultaneously at a high temporal cadence taken with the Crisp Imaging Spectropolarimeter at the Swedish Solar Telescope on La Palma. In this study, we used a high-quality time sequence for RBEs at different blueshifts and employed an automated detection routine to detect a large number of RBEs in order to expand on the statistics of RBEs. We find that the number of detected RBEs is strongly dependent on the associated Doppler velocity of the images on which the search is performed. Automatic detection of RBEs at lower velocities increases the estimated number of RBEs to the same order of magnitude expected from limb spicules. This shows that RBEs and type II spicules are indeed exponents of the same phenomenon. Furthermore, we provide solid evidence that Ca II 8542 RBEs are connected to H{alpha} RBEs and are located closer to the network regions with the H{alpha} RBEs being a continuation of the Ca II 8542 RBEs. Our results show that RBEs have an average lifetime of 83.9 s when observed in both spectral lines and that the Doppler velocities of RBEs range from 10 to 25 km s{sup -1} in Ca II 8542 and 30 to 50 km s{sup -1} in H{alpha}. In addition, we automatically determine the transverse motion of a much larger sample of RBEs than previous studies, and find that, just like type II spicules, RBEs undergo significant transverse motions of the order of 5-10 km s{sup -1}. Finally, we find that the intergranular jets discovered at Big Bear Solar Observatory are a subset of RBEs.

  17. Crown ether-modified electrodes for the simultaneous stripping voltammetric determination of Cd(II), Pb(II) and Cu(II).

    PubMed

    Serrano, Núria; González-Calabuig, Andreu; del Valle, Manel

    2015-06-01

    This work describes the immobilization of 4-carboxybenzo-18-crown-6 (CB-18-crown-6) and 4-carboxybenzo-15-crown-5 (CB-15-crown-5) assisted by lysine on aryl diazonium salt monolayers anchored to the surface of graphite-epoxy composite electrodes (GEC), and their use for the simultaneous determination of Cd(II), Pb(II) and Cu(II) by differential pulse anodic stripping voltammetry (DPASV). These modified electrodes display a good repeatability and reproducibility with detection and quantification limits at levels of µg L(-1) (ppb), confirming their suitability for the determination of Cd(II), Pb(II) and Cu(II) ions in environmental samples. The overlapped nature of the multimetal stripping measurements was resolved by employing the two-sensor array CB-15-crown-5-GEC and CB-18-crown-6-GEC, since the metal complex selectivity exhibited by the considered ligands could add some discrimination power. For the processing of the voltammograms, Discrete Wavelet Transform and Causal Index were selected as preprocessing tools for data compression coupled with an artificial neural network for the modeling of the obtained responses, allowing the resolution of mixtures of these metals with good prediction of their concentrations (correlation with expected values for an external test subset better than 0.942). PMID:25863381

  18. An Analytical Chemistry Experiment in Simultaneous Spectrophotometric Determination of Fe(III) and Cu(II) with Hexacyanoruthenate(II) Reagent.

    ERIC Educational Resources Information Center

    Mehra, M. C.; Rioux, J.

    1982-01-01

    Experimental procedures, typical observations, and results for the simultaneous analysis of Fe(III) and Cu(II) in a solution are discussed. The method is based on selective interaction between the two ions and potassium hexacyanoruthenate(II) in acid solution involving no preliminary sample preparations. (Author/JN)

  19. Single peak parameters technique for simultaneous measurements: Spectrophotometric sequential injection determination of Fe(II) and Fe(III).

    PubMed

    Kozak, J; Paluch, J; Węgrzecka, A; Kozak, M; Wieczorek, M; Kochana, J; Kościelniak, P

    2016-02-01

    Spectrophotometric sequential injection system (SI) is proposed to automate the method of simultaneous determination of Fe(II) and Fe(III) on the basis of parameters of a single peak. In the developed SI system, sample and mixture of reagents (1,10-phenanthroline and sulfosalicylic acid) are introduced into a vessel, where in an acid environment (pH≅3) appropriate compounds of Fe(II) and Fe(III) with 1,10-phenanthroline and sulfosalicylic acid are formed, respectively. Then, in turn, air, sample, EDTA and sample again, are introduced into a holding coil. After the flow reversal, a segment of air is removed from the system by an additional valve and as EDTA replaces sulfosalicylic acid forming a more stable colorless compound with Fe(III), a complex signal is registered. Measurements are performed at wavelength 530 nm. The absorbance measured at minimum of the negative peak and the area or the absorbance measured at maximum of the signal can be used as measures corresponding to Fe(II) and Fe(III) concentrations, respectively. The time of the peak registration is about 2 min. Two-component calibration has been applied to analysis. Fe(II) and Fe(III) can be determined within the concentration ranges of 0.04-4.00 and 0.1-5.00 mg L(-1), with precision less than 2.8% and 1.7% (RSD), respectively and accuracy better than 7% (RE). The detection limit is 0.04 and 0.09 mg L(-1) for Fe(II) and Fe(III), respectively. The method was applied to analysis of artesian water samples. PMID:26653493

  20. Simultaneous trace-levels determination of Hg(II) and Pb(II) ions in various samples using a modified carbon paste electrode based on multi-walled carbon nanotubes and a new synthesized Schiff base.

    PubMed

    Afkhami, Abbas; Bagheri, Hasan; Khoshsafar, Hosein; Saber-Tehrani, Mohammad; Tabatabaee, Masoumeh; Shirzadmehr, Ali

    2012-10-01

    A modified carbon paste electrode based on multi-walled carbon nanotubes (MWCNTs) and 3-(4-methoxybenzylideneamino)-2-thioxothiazolodin-4-one as a new synthesized Schiff base was constructed for the simultaneous determination of trace amounts of Hg(II) and Pb(II) by square wave anodic stripping voltammetry. The modified electrode showed an excellent selectivity and stability for Hg(II) and Pb(II) determinations and for accelerated electron transfer between the electrode and the analytes. The electrochemical properties and applications of the modified electrode were studied. Operational parameters such as pH, deposition potential and deposition time were optimized for the purpose of determination of traces of metal ions at pH 3.0. Under optimal conditions the limits of detection, based on three times the background noise, were 9.0×10(-4) and 6.0×10(-4) μmol L(-1) for Hg(II) and Pb(II) with a 90 s preconcentration, respectively. In addition, the modified electrode displayed a good reproducibility and selectivity, making it suitable for the simultaneous determination of Hg(II) and Pb(II) in real samples such as sea water, waste water, tobacco, marine and human teeth samples. PMID:22975186

  1. Reevaluation of stratospheric ozone trends from SAGE II data using a simultaneous temporal and spatial analysis

    NASA Astrophysics Data System (ADS)

    Damadeo, R. P.; Zawodny, J. M.; Thomason, L. W.

    2014-12-01

    This paper details a new method of regression for sparsely sampled data sets for use with time-series analysis, in particular the Stratospheric Aerosol and Gas Experiment (SAGE) II ozone data set. Non-uniform spatial, temporal, and diurnal sampling present in the data set result in biased values for the long-term trend if not accounted for. This new method is performed close to the native resolution of measurements and is a simultaneous temporal and spatial analysis that accounts for potential diurnal ozone variation. Results show biases, introduced by the way data are prepared for use with traditional methods, can be as high as 10%. Derived long-term changes show declines in ozone similar to other studies but very different trends in the presumed recovery period, with differences up to 2% per decade. The regression model allows for a variable turnaround time and reveals a hemispheric asymmetry in derived trends in the middle to upper stratosphere. Similar methodology is also applied to SAGE II aerosol optical depth data to create a new volcanic proxy that covers the SAGE II mission period. Ultimately this technique may be extensible towards the inclusion of multiple data sets without the need for homogenization.

  2. Reevaluation of stratospheric ozone trends from SAGE II data using a simultaneous temporal and spatial analysis

    NASA Astrophysics Data System (ADS)

    Damadeo, R. P.; Zawodny, J. M.; Thomason, L. W.

    2014-07-01

    This paper details a new method of regression for sparsely sampled data sets for use with time-series analysis, in particular the Stratospheric Aerosol and Gas Experiment (SAGE) II ozone data set. Non-uniform spatial, temporal, and diurnal sampling present in the data set result in biased values for the long-term trend if not accounted for. This new method is performed close to the native resolution of measurements and is a simultaneous temporal and spatial analysis that accounts for any potential diurnal variation. Results show declines in ozone similar to other studies but very different trends in the recovery period. The regression model allows for a variable turnaround time and reveals a~hemispheric asymmetry in the middle to upper stratosphere. Similar methodology is also applied to SAGE II aerosol optical depth data to create a new volcanic proxy that covers the SAGE II mission period. Ultimately this technique may be extensible towards the inclusion of multiple data sets without the need for homogenization.

  3. Reevaluation of Stratospheric Ozone Trends From SAGE II Data Using a Simultaneous Temporal and Spatial Analysis

    NASA Technical Reports Server (NTRS)

    Damadeo, R. P.; Zawodny, J. M.; Thomason, L. W.

    2014-01-01

    This paper details a new method of regression for sparsely sampled data sets for use with time-series analysis, in particular the Stratospheric Aerosol and Gas Experiment (SAGE) II ozone data set. Non-uniform spatial, temporal, and diurnal sampling present in the data set result in biased values for the long-term trend if not accounted for. This new method is performed close to the native resolution of measurements and is a simultaneous temporal and spatial analysis that accounts for potential diurnal ozone variation. Results show biases, introduced by the way data is prepared for use with traditional methods, can be as high as 10%. Derived long-term changes show declines in ozone similar to other studies but very different trends in the presumed recovery period, with differences up to 2% per decade. The regression model allows for a variable turnaround time and reveals a hemispheric asymmetry in derived trends in the middle to upper stratosphere. Similar methodology is also applied to SAGE II aerosol optical depth data to create a new volcanic proxy that covers the SAGE II mission period. Ultimately this technique may be extensible towards the inclusion of multiple data sets without the need for homogenization.

  4. Addition of simultaneous heat and solute transport and variable fluid viscosity to SEAWAT

    USGS Publications Warehouse

    Thorne, D.; Langevin, C.D.; Sukop, M.C.

    2006-01-01

    SEAWAT is a finite-difference computer code designed to simulate coupled variable-density ground water flow and solute transport. This paper describes a new version of SEAWAT that adds the ability to simultaneously model energy and solute transport. This is necessary for simulating the transport of heat and salinity in coastal aquifers for example. This work extends the equation of state for fluid density to vary as a function of temperature and/or solute concentration. The program has also been modified to represent the effects of variable fluid viscosity as a function of temperature and/or concentration. The viscosity mechanism is verified against an analytical solution, and a test of temperature-dependent viscosity is provided. Finally, the classic Henry-Hilleke problem is solved with the new code. ?? 2006 Elsevier Ltd. All rights reserved.

  5. Scanning thermal microscopy probe capable of simultaneous electrical imaging and the addition of diamond tip

    NASA Astrophysics Data System (ADS)

    Brown, E.; Hao, L.; Cox, D. C.; Gallop, J. C.

    2008-03-01

    Scanning Thermal Microscopy (SThM) is a scanning probe technique that allows the mapping of the thermal properties and/or temperature of a substrate. Developments in this scanning probe technique are of great importance to further the study of thermal transport at the micron and at the nano scale, for instance to better the understanding of heat transport in nano-electronic devices or energy transfer in biological systems. Here we describe: 1) the scanning technique developed to acquire simultaneous images of the topography, the thermal and electrical properties of the substrate using a commercially available Veeco SThM probe; 2) how the SThM probe was modified by mounting a micron-sized diamond pyramid on its tip in order to improve the probe's lateral resolution and the topography resolution tests on the performance of the modified probe.

  6. Simultaneous spectrophotometric determination of chromium(VI) and iron (III) by H-point standard addition method

    NASA Astrophysics Data System (ADS)

    Larionova, E. V.; Bulygina, K. A.

    2016-02-01

    In this work the possibility of simultaneous spectrophotometric determination of chromium (VI) and iron (III) in alloys with help of the mixed organic reagent (diphenylcarbazide and 1,10-phenanthroline) is studied. We have applied H-point standard addition method to determine concentrations of chromium (VI) and iron (III) from the mixture. The pure signals of complexes of chromium (VI) with diphenylcarbazide and iron (III) with the 1,10-phenanthroline and their calibration plots are previously carried out. We established the possibility of simultaneous determination of chromium (VI) and iron (III) in the different concentration ranges by H-point standard addition method. Correctness of determination of concentration by means of the offered technique is proved by "added-found" method for a series of mixtures with different ratios of concentration of chromium (VI) and iron (III). It is founded that the error of determination of concentration doesn't exceed 33%.

  7. A solar type II radio burst from coronal mass ejection-coronal ray interaction: Simultaneous radio and extreme ultraviolet imaging

    SciTech Connect

    Chen, Yao; Du, Guohui; Feng, Shiwei; Kong, Xiangliang; Wang, Bing; Feng, Li; Guo, Fan; Li, Gang

    2014-05-20

    Simultaneous radio and extreme ultraviolet (EUV)/white-light imaging data are examined for a solar type II radio burst occurring on 2010 March 18 to deduce its source location. Using a bow-shock model, we reconstruct the three-dimensional EUV wave front (presumably the type-II-emitting shock) based on the imaging data of the two Solar TErrestrial RElations Observatory spacecraft. It is then combined with the Nançay radio imaging data to infer the three-dimensional position of the type II source. It is found that the type II source coincides with the interface between the coronal mass ejection (CME) EUV wave front and a nearby coronal ray structure, providing evidence that the type II emission is physically related to the CME-ray interaction. This result, consistent with those of previous studies, is based on simultaneous radio and EUV imaging data for the first time.

  8. Dependency of simultaneous Cr(VI), Cu(II) and Cd(II) reduction on the cathodes of microbial electrolysis cells self-driven by microbial fuel cells

    NASA Astrophysics Data System (ADS)

    Zhang, Yong; Yu, Lihua; Wu, Dan; Huang, Liping; Zhou, Peng; Quan, Xie; Chen, Guohua

    2015-01-01

    Microbial fuel cells (MFCs) using either Cr(VI) (MFCsCr) or Cu(II) (MFCsCu) as a final electron acceptor, are stacked to self-drive microbial electrolysis cells (MECs) using Cd(II) (MECsCd) as an electron acceptor for simultaneous reduction of Cr(VI) in MFCsCr, Cu(II) in MFCsCu and Cd(II) in MECsCd with no external energy consumption. Titanium sheet (TS) and carbon rod (CR) as the cathodes of MECsCd are assessed for efficient system performance. MFCsCr and MFCsCu in series is superior to the parallel configuration, and higher Cd(II) reduction along with simultaneous Cr(VI) and Cu(II) reduction supports TS function as a good cathode material. Conversely, CR can not entirely proceed Cd(II) reduction in MECsCd despite of more Cr(VI) and Cu(II) reduction in the same serial configuration than either system alone. While a decrease in cathode volume in both MFCsCr and MFCsCu with serial connection benefits to reduction of Cr(VI) in MFCsCr and Cu(II) in MFCsCu, Cd(II) reduction in MECsCd is substantially enhanced under a decrease in cathode volume in individual MFCsCr and serially connected with volume-unchanged MFCsCu. This study demonstrates simultaneous Cr(VI), Cu(II) and Cd(II) recovery from MFCsCr-MFCsCu-MECsCd self-driven system is feasible, and TS as the cathodes of MECsCd is critical for efficient system performance.

  9. Simultaneous absorption of NO and SO2 into hexamminecobalt(II)/iodide solution.

    PubMed

    Long, Xiang-Li; Xiao, Wen-De; Yuan, Wei-kang

    2005-05-01

    An innovative catalyst system has been developed to simultaneously remove NO and SO2 from combustion flue gas. Such catalyst system may be introduced to the scrubbing solution using ammonia solution to accomplish sequential absorption and catalytic oxidation of both NO and SO2 in the same reactor. When the catalyst system is utilized for removing NO and SO2 from the flue gas, Co(NH3)(6)2+ ions act as the catalyst and I- as the co-catalyst. Dissolved oxygen, in equilibrium with the residual oxygen in the flue gas, is the oxidant. The overall removal process is further enhanced by UV irradiation at 365 nm. More than 95% of NO is removed at a feed concentration of 250-900 ppm, and nearly 100% of SO2 is removed at a feed concentration of 800-2500 ppm. The sulfur dioxide co-existing in the flue gas is beneficial to NO absorption into hexamminecobalt(II)/iodide solution. NO and SO2 can be converted to ammonium sulfate and ammonium nitrate that can be used as fertilizer materials. The process described here demonstrates the feasibility of removing SO2 and NO simultaneously only by retrofitting the existing wet ammonia flue-gas-desulfurization (FGD) scrubbers. PMID:15811409

  10. Simultaneous determination of Cd(II), Cu(II), Pb(II), and Zn(II) in citrus essential oils by derivative potentiometric stripping analysis.

    PubMed

    La Pera, Lara; Saitta, Marcello; Di Bella, Giuseppa; Dugo, Giacomo

    2003-02-26

    Citrus essential oils are widely used in the food, cosmetics, and pharmaceutical industries, so the determination of heavy metals content is of great importance to guarantee their quality. The present work deals with the quantification of Cd(II), Cu(II), Pb(II), and Zn(II) in different varieties of citrus essential oils, using derivative potentiometric stripping analysis. Two different metals extraction procedures, involving concentrated hydrochloric acid treatment and acid-alcoholic dissolution, are tested on lemon, mandarin, sweet orange, and bergamot essential oils, and they give very similar results. Cd(II), Cu(II), Pb(II), and Zn(II) recovery tests spanned from 95 to 100.50%, providing evidence that metals quantification remained unaffected by the cleanup steps of the two procedures. The repeatability of the hydrochloric acid extraction method, applied on different varieties of essential oils, is >95.00% for Cd(II), Cu(II), Pb(II), and Zn(II), whereas the repeatability of the acid-alcoholic dissolution method is >93.00% for Cu and Cd only in lemon oil. Detection limits obtained for the four analytes, using both procedures, ranged from 0.10 to 0.98 ng g(-)(1) in lemon, mandarin, sweet orange, and bergamot essential oils. PMID:12590445

  11. Enhancement of mercury capture by the simultaneous addition of hydrogen bromide (HBr) and fly ashes in a slipstream facility.

    PubMed

    Cao, Yan; Wang, Quan-Hai; Li, Jun; Cheng, Jen-Chieh; Chan, Chia-Chun; Cohron, Marten; Pan, Wei-Ping

    2009-04-15

    Low halogen content in tested Powder River Basin (PRB) coals and low loss of ignition content (LOI) in PRB-derived fly ash were likely responsible for higher elemental mercury content (averaging about 75%) in the flue gas and also lower mercury capture efficiency by electrostatic precipitator (ESP) and wet-FGD. To develop a cost-effective approach to mercury capture in a full-scale coal-fired utility boiler burning PRB coal, experiments were conducted adding hydrogen bromide (HBr) or simultaneously adding HBr and selected fly ashes in a slipstream reactor (0.152 x 0.152 m) under real flue gas conditions. The residence time of the flue gas inside the reactorwas about 1.4 s. The average temperature of the slipstream reactor was controlled at about 155 degrees C. Tests were organized into two phases. In Phase 1, only HBr was added to the slipstream reactor, and in Phase 2, HBr and selected fly ash were added simultaneously. HBr injection was effective (>90%) for mercury oxidation at a low temperature (155 degrees C) with an HBr addition concentration of about 4 ppm in the flue gas. Additionally, injected HBr enhanced mercury capture by PRB fly ash in the low-temperature range. The mercury capture efficiency, attesting conditions of the slipstream reactor, reached about 50% at an HBr injection concentration of 4 ppm in the flue gas. Compared to only the addition of HBr, simultaneously adding bituminous-derived fly ash in a minimum amount (30 lb/MMacf), together with HBr injection at 4 ppm, could increase mercury capture efficiency by 30%. Injection of lignite-derived fly ash at 30 lb/MMacf could achieve even higher mercury removal efficiency (an additional 35% mercury capture efficiency compared to HBr addition alone). PMID:19475955

  12. Enhancement of mercury capture by the simultaneous addition of hydrogen bromide (HBr) and fly ashes in a slipstream facility

    SciTech Connect

    Yan Cao; Quan-Hai Wang; Jun Li; Jen-Chieh Cheng; Chia-Chun Chan; Marten Cohron; Wei-Ping Pan

    2009-04-15

    Low halogen content in tested Powder River Basin (PRB) coals and low loss of ignition content (LOI) in PRB-derived fly ash were likely responsible for higher elemental mercury content (averaging about 75%) in the flue gas and also lower mercury capture efficiency by electrostatic precipitator (ESP) and wet-FGD. To develop a cost-effective approach to mercury capture in a full-scale coal-fired utility boiler burning PRB coal, experiments were conducted adding hydrogen bromide (HBr) or simultaneously adding HBr and selected fly ashes in a slipstream reactor (0.152 x 0.152 m) under real flue gas conditions. The residence time of the flue gas inside the reactor was about 1.4 s. The average temperature of the slipstream reactor was controlled at about 155{sup o}C. Tests were organized into two phases. In Phase 1, only HBr was added to the slipstream reactor, and in Phase 2, HBr and selected fly ash were added simultaneously. HBr injection was effective (>90%) for mercury oxidation at a low temperature (155{sup o}C) with an HBr addition concentration of about 4 ppm in the flue gas. Additionally, injected HBr enhanced mercury capture by PRB fly ash in the low-temperature range. The mercury capture efficiency, at testing conditions of the slipstream reactor, reached about 50% at an HBr injection concentration of 4 ppm in the flue gas. Compared to only the addition of HBr, simultaneously adding bituminous-derived fly ash in a minimum amount (30 lb/MMacf), together with HBr injection at 4 ppm, could increase mercury capture efficiency by 30%. Injection of lignite-derived fly ash at 30 lb/MMacf could achieve even higher mercury removal efficiency (an additional 35% mercury capture efficiency compared to HBR addition alone). 25 refs., 5 figs., 1 tab.

  13. Immobilization of Cu(II), Pb(II) and Cd(II) by the addition of rice straw derived biochar to a simulated polluted Ultisol.

    PubMed

    Jiang, Jun; Xu, Ren-kou; Jiang, Tian-yu; Li, Zhuo

    2012-08-30

    To develop new remediation methods for acidic soils polluted by heavy metals, the chemical fractions of Cu(II), Pb(II) and Cd(II) in an Ultisol with and without rice straw biochar were compared and the effect of biochar incorporation on the mobility and bioavailability of these metals was investigated. In light of the decreasing zeta potential and increasing CEC, the incorporation of biochar made the negative soil surface charge more negative. Additionally, the soil pH increased markedly after the addition of biochar. These changes in soil properties were advantageous for heavy metal immobilization in the bulk soil. The acid soluble Cu(II) and Pb(II) decreased by 19.7-100.0% and 18.8-77.0%, respectively, as the amount of biochar added increased. The descending range of acid soluble Cd(II) was 5.6-14.1%, which was much lower than that of Cu(II) and Pb(II). When 5.0 mmol/kg of these heavy metals was added, the reducible Pb(II) for treatments containing 3% and 5% biochar was 2.0 and 3.0 times higher than that of samples without biochar, while the reducible Cu(II) increased by 61.6% and 132.6% for the corresponding treatments, respectively. When 3% and 5% biochar was added, the oxidizable portion of Pb(II) increased by 1.18 and 1.94 times, respectively, while the oxidizable portion of Cu(II) increased by 8.13 and 7.16 times, respectively, primarily due to the high adsorption affinity of functional groups of biochar to Cu(II). The residual heavy metal contents were low and changed little with the incorporation of biochar. PMID:22704774

  14. Method for simultaneous use of a single additive for coal flotation, dewatering, and reconstitution

    DOEpatents

    Wen, Wu-Wey; Gray, McMahan L.; Champagne, Kenneth J.

    1995-01-01

    A single dose of additive contributes to three consecutive fine coal unit operations, i.e., flotation, dewatering and reconstitution, whereby the fine coal is first combined with water in a predetermined proportion so as to formulate a slurry. The slurry is then mixed with a heavy hydrocarbon-based emulsion in a second predetermined proportion and at a first predetermined mixing speed and for a predetermined period of time. The conditioned slurry is then cleaned by a froth flotation method to form a clean coal froth and then the froth is dewatered by vacuum filtration or a centrifugation process to form reconstituted products that are dried to dust-less clumps prior to combustion.

  15. Method for simultaneous use of a single additive for coal flotation, dewatering and reconstitution

    SciTech Connect

    Wen, Wu-Wey; Gray, M.L.; Champagne, K.J.

    1993-11-09

    A single dose of additive contributes to three consecutive fine coal unit operations, i.e., flotation, dewatering and reconstitution, whereby the fine coal is first combined with water in a predetermined proportion so as to formulate a slurry. The slurry is then mixed with a heavy hydrocarbon-based emulsion in a second predetermined proportion and at a first predetermined mixing speed and for a predetermined period of time. The conditioned slurry is then cleaned by a froth flotation method to form a clean coal froth and then the froth is dewatered by vacuum filtration or a centrifugation process to form reconstituted products that are dried to dust-less clumps prior to combustion.

  16. Simultaneous Addition of Shikonin and Its Derivatives with Lipopolysaccharide Induces Rapid Macrophage Death.

    PubMed

    Koike, Atsushi; Shibano, Makio; Mori, Hideya; Kohama, Kiyoko; Fujimori, Ko; Amano, Fumio

    2016-01-01

    Macrophages play pivotal roles in inflammatory responses. Previous studies showed that various natural products exert antiinflammatory effects by regulating macrophage activation. Recent studies have shown that shikonin (SHK) and its derivatives (β-hydroxyisovalerylshikonin, acetylshikonin, and isobutylshikonin), which are 1,4-naphthoquinone pigments extracted from the roots of Lithospermum erythrorhizon, have various pharmacological, including antiinflammatory and antitumor, effects. Even though there have been many studies on the antiinflammatory activities of SHK derivatives, only a few have described their direct effects on macrophages. We investigated the effects of SHK derivatives on lipopolysaccharide (LPS)-treated macrophages. Low doses of SHK derivatives induced significant macrophage cytotoxicity (mouse macrophage-like J774.1/JA-4 cells and mouse peritoneal macrophages) in the presence of LPS. SHK activated caspases-3 and -7, which led to DNA fragmentation, but this cytotoxicity was prevented through a pan-caspase inhibitor in LPS-treated JA-4 cells. Maximal cytotoxic effects were achieved when SHK was added immediately before LPS addition. These results indicate that SHK derivatives induce caspase-dependent apoptotic cell death of LPS-treated macrophages and suggest that SHK acts during an early stage of LPS signaling. PMID:27251498

  17. Generalized net analyte signal standard addition as a novel method for simultaneous determination: application in spectrophotometric determination of some pesticides.

    PubMed

    Asadpour-Zeynali, Karim; Saeb, Elhameh; Vallipour, Javad; Bamorowat, Mehdi

    2014-01-01

    Simultaneous spectrophotometric determination of three neonicotinoid insecticides (acetamiprid, imidacloprid, and thiamethoxam) by a novel method named generalized net analyte signal standard addition method (GNASSAM) in some binary and ternary synthetic mixtures was investigated. For this purpose, standard addition was performed using a single standard solution consisting of a mixture of standards of all analytes. Savings in time and amount of used materials are some of the advantages of this method. All determinations showed appropriate applicability of this method with less than 5% error. This method may be applied for linearly dependent data in the presence of known interferents. The GNASSAM combines the advantages of both the generalized standard addition method and net analyte signal; therefore, it may be a proper alternative for some other multivariate methods. PMID:24672886

  18. Simultaneous control of acid gases and PAHs using a spray dryer combined with a fabric filter using different additives.

    PubMed

    Liu, Zhen Shu; Wey, Ming Yen; Lin, Chiou Liang

    2002-04-26

    The purpose of this research was to simultaneously evaluate the removal efficiency of acid gases and PAHs from the flue gas emitted by a laboratory incinerator. This flue gas contained dust, acid gases, organics and heavy metals. A spray dryer combined with a fabric filter was used as the air pollution control device (APCD) in this study. The operating conditions investigated included different feedstock additives (polyvinyl chloride (PVC) and NaCl) and spray dryer additives (SiO2, CaCl2 and NaHCO3). The removal efficiency for SO2 could be enhanced by adding inorganic additives, such as SiO2, CaCl2 and NaHCO3. The presence of PVC in the incinerator feedstock also increased the removal efficiency of SO2in the spray dryer. The improved removal of PAHs could be attributed to the addition of feedstock additives (PVC and NaCl) and spray dryer additives (SiO2, CaCl2 and NaHCO3). PMID:11900910

  19. Simultaneous type I and type II Čerenkov-phase matched second-harmonic generation in disordered nonlinear photonic structures.

    PubMed

    Ayoub, Mousa; Paßlick, Markus; Imbrock, Jörg; Denz, Cornelia

    2015-11-01

    We observe simultaneous type I and II Čerenkov-phase matched second-harmonic generation in a disordered nonlinear photonic crystal. The mean width of the disordered ferroelectric domains and the laser beam width are adjusted to be on the same length scale. We analyze the polarization properties, emission angles and intensities of each process. PMID:26561107

  20. Cu(II) removal by Anoxybacillus flavithermus-iron oxide composites during the addition of Fe(II)aq

    NASA Astrophysics Data System (ADS)

    Franzblau, Rachel E.; Daughney, Christopher J.; Swedlund, Peter J.; Weisener, Christopher G.; Moreau, Magali; Johannessen, Bernt; Harmer, Sarah L.

    2016-01-01

    There is currently poor understanding of metal removal by composites of bacteria and iron oxide minerals, even though they commonly co-occur and are among the most important sorbents in near-surface fluid-rock environments. This study evaluated Cu removal by composites of Anoxybacillus flavithermus and iron oxide over time during the addition, oxidation, and hydrolysis of Fe(II)aq and precipitation of the mineral, in comparison to Cu removal in the two single-sorbent end-member systems. In the absence of iron oxide, Cu removal by A. flavithermus was well described by a previously published surface complexation model, after inclusion of additional reactions describing aqueous complexation by exudate ligands released by the bacteria. In the absence of bacterial cells, Cu removal by iron oxide synthesized in the presence of the bacterial exudate ligands demonstrated the formation of ternary surface complexes. Removal of Cu by the A. flavithermus-iron oxide composites was ca. 20% greater than the prediction based on assumption of additivity in the two end-member systems. This non-additive behavior was attributed to (1) progressive physical blockage of bacterial surface sites by the iron oxide particles, (2) physical blockage of adsorption sites as a result of self-aggregation of the iron oxide particles, and (3) the reduction of Cu(II) to Cu(I) at the bacterial cell surface, as demonstrated by X-ray absorption spectroscopy. The extent of reduction of Cu(II) to Cu(I) was proportional to the concentration of solid phase Fe(II), suggesting that iron oxidation and copper reduction are linked. This study has shown that Cu removal by bacteria-iron oxide composites is greatly affected by redox processes such as Cu(II) reduction on the cell surface both by other bacterial surface ligands and the oxidation of sorbed Fe(II), as well as Fe(II) redox interactions, and aging effects of the mineral (i.e. surface site masking).

  1. Pd(II)-Catalyzed Asymmetric Addition of Arylboronic Acids to Isatin-Derived Ketimines.

    PubMed

    He, Qun; Wu, Liang; Kou, Xuezhen; Butt, Nicholas; Yang, Guoqiang; Zhang, Wanbin

    2016-01-15

    A Pd(II)/Pyrox-catalyzed enantioselecitve addition of arylboronic acids to 3-ketimino oxindoles was developed, providing chiral 3-amino-2-oxindoles with a quaternary stereocenter in high yields and with good enantioselectivities. A variety of functionalized 3-ketimino oxindoles can be used, and the method tolerates some variation in arylboronic acid scope. This asymmetric arylation provides an alternative efficient catalytic method for the preparation of chiral 3-aryl-3-amino-2-oxindoles, which also represents the first example of a Pd(II)-catalyzed addition of arylborons to exocyclic ketimines. PMID:26720106

  2. Additives

    NASA Technical Reports Server (NTRS)

    Smalheer, C. V.

    1973-01-01

    The chemistry of lubricant additives is discussed to show what the additives are chemically and what functions they perform in the lubrication of various kinds of equipment. Current theories regarding the mode of action of lubricant additives are presented. The additive groups discussed include the following: (1) detergents and dispersants, (2) corrosion inhibitors, (3) antioxidants, (4) viscosity index improvers, (5) pour point depressants, and (6) antifouling agents.

  3. Spectrophotometric Determination of Iron(II) and Cobalt(II) by Direct, Derivative, and Simultaneous Methods Using 2-Hydroxy-1-Naphthaldehyde-p-Hydroxybenzoichydrazone

    PubMed Central

    Devi, V. S. Anusuya; Reddy, V. Krishna

    2012-01-01

    Optimized and validated spectrophotometric methods have been proposed for the determination of iron and cobalt individually and simultaneously. 2-hydroxy-1-naphthaldehyde-p-hydroxybenzoichydrazone (HNAHBH) reacts with iron(II) and cobalt(II) to form reddish-brown and yellow-coloured [Fe(II)-HNAHBH] and [Co(II)-HNAHBH] complexes, respectively. The maximum absorbance of these complexes was found at 405 nm and 425 nm, respectively. For [Fe(II)-HNAHBH], Beer's law is obeyed over the concentration range of 0.055–1.373 μg mL−1 with a detection limit of 0.095 μg mL−1 and molar absorptivity ɛ, 5.6 × 104 L mol−1 cm−1. [Co(II)-HNAHBH] complex obeys Beer's law in 0.118–3.534 μg mL−1 range with a detection limit of 0.04 μg mL−1 and molar absorptivity, ɛ of 2.3 × 104 L mol−1 cm−1. Highly sensitive and selective first-, second- and third-order derivative methods are described for the determination of iron and cobalt. A simultaneous second-order derivative spectrophotometric method is proposed for the determination of these metals. All the proposed methods are successfully employed in the analysis of various biological, water, and alloy samples for the determination of iron and cobalt content. PMID:22505925

  4. Development and Validation of HPLC Method for the Simultaneous Determination of Five Food Additives and Caffeine in Soft Drinks

    PubMed Central

    Aşçı, Bürge; Dinç Zor, Şule; Aksu Dönmez, Özlem

    2016-01-01

    Box-Behnken design was applied to optimize high performance liquid chromatography (HPLC) conditions for the simultaneous determination of potassium sorbate, sodium benzoate, carmoisine, allura red, ponceau 4R, and caffeine in commercial soft drinks. The experimental variables chosen were pH (6.0–7.0), flow rate (1.0–1.4 mL/min), and mobile phase ratio (85–95% acetate buffer). Resolution values of all peak pairs were used as a response. Stationary phase was Inertsil OctaDecylSilane- (ODS-) 3V reverse phase column (250 × 4.6 mm, 5 μm) dimensions. The detection was performed at 230 nm. Optimal values were found 6.0 pH, 1.0 mL/min flow rate, and 95% mobile phase ratio for the method which was validated by calculating the linearity (r2 > 0.9962), accuracy (recoveries ≥ 95.75%), precision (intraday variation ≤ 1.923%, interday variation ≤ 1.950%), limits of detection (LODs), and limits of quantification (LOQs) parameters. LODs and LOQs for analytes were in the range of 0.10–0.19 μg/mL and 0.33–0.63 μg/mL, respectively. The proposed method was applied successfully for the simultaneous determination of the mixtures of five food additives and caffeine in soft drinks. PMID:26989415

  5. Development and Validation of HPLC Method for the Simultaneous Determination of Five Food Additives and Caffeine in Soft Drinks.

    PubMed

    Aşçı, Bürge; Dinç Zor, Şule; Aksu Dönmez, Özlem

    2016-01-01

    Box-Behnken design was applied to optimize high performance liquid chromatography (HPLC) conditions for the simultaneous determination of potassium sorbate, sodium benzoate, carmoisine, allura red, ponceau 4R, and caffeine in commercial soft drinks. The experimental variables chosen were pH (6.0-7.0), flow rate (1.0-1.4 mL/min), and mobile phase ratio (85-95% acetate buffer). Resolution values of all peak pairs were used as a response. Stationary phase was Inertsil OctaDecylSilane- (ODS-) 3V reverse phase column (250 × 4.6 mm, 5 μm) dimensions. The detection was performed at 230 nm. Optimal values were found 6.0 pH, 1.0 mL/min flow rate, and 95% mobile phase ratio for the method which was validated by calculating the linearity (r (2) > 0.9962), accuracy (recoveries ≥ 95.75%), precision (intraday variation ≤ 1.923%, interday variation ≤ 1.950%), limits of detection (LODs), and limits of quantification (LOQs) parameters. LODs and LOQs for analytes were in the range of 0.10-0.19 μg/mL and 0.33-0.63 μg/mL, respectively. The proposed method was applied successfully for the simultaneous determination of the mixtures of five food additives and caffeine in soft drinks. PMID:26989415

  6. Phase I-II Study of Hypofractionated Simultaneous Integrated Boost With Tomotherapy for Prostate Cancer

    SciTech Connect

    Di Muzio, Nadia Fiorino, Claudio; Cozzarini, Cesare; Alongi, Filippo; Broggi, Sara; Mangili, Paola; Guazzoni, Giorgio; Valdagni, Riccardo; Calandrino, Riccardo; Fazio, Ferruccio

    2009-06-01

    Purpose: To report planning and acute toxicity data of the first 60 patients treated within a Phase I-II study with moderate hypofractionation by image-guided helical tomotherapy. Methods and Materials: Various clinical target volumes (CTVs) were defined: CTV1-pelvic nodes; CTV2-upper portion of seminal vesicles; CTV3-lower portion of SV; CTV4-prostate; overlap between planning target volume (PTV) 4 and rectum. Different doses to each PTV were simultaneously delivered in 28 fractions. For 31 low-risk patients: 56.0, 61.6, and 71.4 Gy for PTV2-4, respectively; for 20 intermediate-risk patients: 51.8, 61.6, 65.5, and 74.2 Gy for PTV1-4, respectively; for 9 high-risk patients: 51.8 and 65.5 Gy for PTV1-2 and 74.2 Gy for PTV3-4. For all patients, the dose to overlap was 65.5 Gy. Results: The mean fraction of rectum receiving more than 65 Gy (V65) and rectal Dmax were 10% and 70.8 Gy respectively. In cases of pelvic node irradiation, the intestinal cavity (outside PTV) receiving > 45 and 50 Gy was 86 and 12 cc, respectively. A homogeneous dose distribution within each PTV was guaranteed. Acute genitourinary toxicity according to RTOG scoring system was as follows: 21/60 (35%) Grade 1, 12/60 (20%) Grade 2, 2/60 (3%) Grade 3. Acute rectal toxicities were: 18/60 (30%) Grade 1. Twelve (20%) patients showed Grade 1 upper intestinal toxicity (uGI). No patients experienced {>=} Grade 2 acute rectal or uGI side effects. Conclusions: This study shows excellent results with regard to acute toxicity. Further research is necessary to assess definitive late toxicity and tumor control outcome.

  7. Radiation graft modification of ethylene-propylene rubber—II. Effect of additives

    NASA Astrophysics Data System (ADS)

    Haddadi-Asl, V.; Burford, R. P.; Garnett, J. L.

    1995-02-01

    The effect of multifunctional acrylic additives including TMPTA, PEGDA and PGTA on the radiation grafting of hydrophilic vinyl monomers onto ethylene—propylene elastomer (EPM rubbers) was studied. This work centres upon gamma irradiation-induced grafting of acrylamide (AAm), N-vinyl-2-pyrrolidone (NVP), 2-hydroxyethyl methacrylate (HEMA) and acrylonitrile (AN) onto EPM rubber by the simultaneous method. Water proved to be an effective solvent but methanol lowered grafting. Sulphuric acid was detrimental to both homopolymerisation and grafting, a result consistent with the theory proposed for the role of this additive in polymer grafting systems.

  8. Simultaneous separation of acidic and basic proteins using gemini pyrrolidinium surfactants and hexafluoroisopropanol as dynamic coating additives in capillary electrophoresis.

    PubMed

    Tian, Yu; Li, Yunfang; Mei, Jie; Cai, Bo; Dong, Jinfeng; Shi, Zhiguo; Xiao, Yuxiu

    2015-09-18

    The separation of acidic and basic proteins using CE has been limited in part due to the adsorption of proteins onto the capillary wall. In this work, the efficient control of EOF and the simultaneous separation of acidic and basic proteins are achieved by use of C18-4-C18PB as a dynamic coating additive, which is a representative surfactant for 1,1'-(butane-1,s-alkyl)bis(1-alkylpyrrolidinium) bromide (Cn-4-CnPB, n=10, 12, 14, 16 and 18). C18-4-C18PB exhibits a powerful capability in the reversal of EOF, and a low concentration even less than 0.001 mM is sufficient to reverse EOF at the tested pH values (3.0-9.0). Baseline separation of eight proteins with sharp peaks and high efficiencies (54,000-297,000 plates/m) is obtained with 30 mM NaH2PO4 buffer (pH 5.0) containing 4 mM C18-4-C18PB. At the same buffer condition, the Cn-4-CnPB with shorter alkyl chain (n=10, 12, 14, 16) cannot achieve the same effective protein separation as C18-4-C18PB. However, the combined use of small amounts (≤0.5%, v/v) of hexafluoroisopropanol (HFIP) and Cn-4-CnPB (n=10, 12, 14, 16) as additives can completely separate all eight proteins with high efficiencies of 81,000-318,000 plates/m. The RSDs of migration time are less than 0.80% and 5.84% for run-to-run and day-to-day assays (n=5), respectively, and the protein recoveries are larger than 90.15%. To the best of our knowledge, this is the first report on the simultaneous separation of acidic and basic proteins using Cn-4-CnPB surfactants or Cn-4-CnPB surfactants combined with HFIP as dynamic coating additives. PMID:26300480

  9. Addition of hydrogen peroxide for the simultaneous control of bromate and odor during advanced drinking water treatment using ozone.

    PubMed

    Wang, Yongjing; Yu, Jianwei; Zhang, Dong; Yang, Min

    2014-03-01

    Complete removal of the characteristic septic/swampy odor from Huangpu River source water could only be achieved under an ozone dose as high as 4.0 mg/L in an ozone-biological activated carbon (O3-BAC) process, which would lead to the production of high concentrations of carcinogenic bromate due to the high bromide content. This study investigated the possibility of simultaneous control of bromate and the septic/swampy odor by adding H2O2 prior to the O3-BAC process for the treatment of Huangpu River water. H2O2 addition could reduce the bromate concentration effectively at an H2O2/O3 (g/g) ratio of 0.5 or higher. At the same time, the septic/swampy odor removal was enhanced by the addition of H2O2, although optimization of the H2O2/O3 ratio was required for each ozone dose. At an ozone dose of 2.0 mg/L, the odor was removed completely at an H2O2/O3 ratio of 0.5. The results indicated that H2O2 application at a suitable dose could enhance the removal of the septic/swampy odor while suppressing the formation of bromate during ozonation of Huangpu River source water. PMID:25079267

  10. Net analyte signal standard addition method for simultaneous determination of sulphadiazine and trimethoprim in bovine milk and veterinary medicines.

    PubMed

    Hajian, Reza; Mousavi, Esmat; Shams, Nafiseh

    2013-06-01

    Net analyte signal standard addition method has been used for the simultaneous determination of sulphadiazine and trimethoprim by spectrophotometry in some bovine milk and veterinary medicines. The method combines the advantages of standard addition method with the net analyte signal concept which enables the extraction of information concerning a certain analyte from spectra of multi-component mixtures. This method has some advantages such as the use of a full spectrum realisation, therefore it does not require calibration and prediction step and only a few measurements require for the determination. Cloud point extraction based on the phenomenon of solubilisation used for extraction of sulphadiazine and trimethoprim in bovine milk. It is based on the induction of micellar organised media by using Triton X-100 as an extraction solvent. At the optimum conditions, the norm of NAS vectors increased linearly with concentrations in the range of 1.0-150.0 μmolL(-1) for both sulphadiazine and trimethoprim. The limits of detection (LOD) for sulphadiazine and trimethoprim were 0.86 and 0.92 μmolL(-1), respectively. PMID:23411170

  11. Kinetic spectrophotometric determination of Fe(II) in the presence of Fe(III) by H-point standard addition method in mixed micellar medium.

    PubMed

    Hasani, Masoumeh; Rezaei, Alireza; Abdollahi, Hamid

    2007-11-01

    The H-point standard addition method was applied to kinetic data for simultaneous determination of Fe(II) and Fe(III) or selective determination of Fe(II) in the presence of Fe(III). The method is based on the difference in the rate of complex formation between iron in two different oxidation states and methylthymol blue (MTB) at pH 3.5 in mixed cetyltrimethylammonium bromide (CTAB) and Triton X-100 micellar medium. Fe(II) can be determined in the range 0.25-2.5 microg ml(-1) with satisfactory accuracy and precision in the presence of excess Fe(III) and other metal ions that rapidly form complexes with MTB under working condition. The proposed method was successfully applied to the simultaneous determination of Fe(II) and Fe(III) or selective determination of Fe(II) in the presence of Fe(III) in spiked real environmental and synthetic samples with complex composition. PMID:17329160

  12. Net analyte signal standard addition method (NASSAM) as a novel spectrofluorimetric and spectrophotometric technique for simultaneous determination, application to assay of melatonin and pyridoxine

    NASA Astrophysics Data System (ADS)

    Asadpour-Zeynali, Karim; Bastami, Mohammad

    2010-02-01

    In this work a new modification of the standard addition method called "net analyte signal standard addition method (NASSAM)" is presented for the simultaneous spectrofluorimetric and spectrophotometric analysis. The proposed method combines the advantages of standard addition method with those of net analyte signal concept. The method can be applied for the determination of analyte in the presence of known interferents. The accuracy of the predictions against H-point standard addition method is not dependent on the shape of the analyte and interferent spectra. The method was successfully applied to simultaneous spectrofluorimetric and spectrophotometric determination of pyridoxine (PY) and melatonin (MT) in synthetic mixtures and in a pharmaceutical formulation.

  13. Evaluation of thiosemicarbazone derivative as chelating agent for the simultaneous removal and trace determination of Cd(II) and Pb(II) in food and water samples.

    PubMed

    Koduru, Janardhan Reddy; Lee, Kap Duk

    2014-05-01

    In the present investigation, prepared N-ethyl-3-carbazolecarbaxaldehyde-3-thiosemicarbazone (ECCT) and employed for the simultaneous removal and determination of trace amounts of Cd(II) and Pb(II) from food and water samples. Cd(II) and Pb(II) gave yellow and orange colored complexes with ECCT in acetate buffer at pH 6.0 with λmax, 380 and 440nm, respectively. Both complexes were easily extractable into kerosene at 1:1(M:L) composition. It was in accordance with Beer's law in the range of 0.0-12.0 and 0.0-10.0μgmL(-1) with 0.999 and 0.997 correlation coefficient for Cd(II) and Pb(II) complexes, respectively, indicated a good linearity between the two variables. The molar absorptivity and Sandell's sensitivity were found to be 0.740×10(4)Lmol(-1)cm(-1), 1.52×10(-3)μgcm(-2) for Cd(II) and 1.809×10(4)L mol(-1)cm(-1), 1.15×10(-3)μgcm(-2) for Pb(II). The precision and accuracy of the method was checked for both metal ions by finding the relative standard deviations (n=8), which were 0.689% and 0.443%, with detection limits of 0.00151μgL(-1) and 0.00264μgL(-1) for Cd(II) and Pb(II), respectively. Further validation using certified reference material, NIST 1568b, resulted in determined concentrations of 0.028±0.253μgg(-1) for Cd(II) and 0.046±0.325μgg(-1) for Pb(II). These determined values agree well with the certified values in the reference materials. The interfering effects of various cations and anions were also studied. The proposed method performance was also evaluated in terms of Student 'T' test and Variance 'F' test, which indicated the significance of the present method parameters, as an inter comparison of the experimental values using ICP-OES. PMID:24360411

  14. Additive Anti-Tumor Effects of Lovastatin and Everolimus In Vitro through Simultaneous Inhibition of Signaling Pathways

    PubMed Central

    Nölting, Svenja; Maurer, Julian; Spöttl, Gerald; Aristizabal Prada, Elke Tatjana; Reuther, Clemens; Young, Karen; Korbonits, Márta; Göke, Burkhard; Grossman, Ashley; Auernhammer, Christoph J.

    2015-01-01

    Background The mTORC1-inhibitor everolimus shows limited efficacy in treating patients with gastro-entero-pancreatic or pulmonary neuroendocrine tumors (NETs), and poor outcome in patients with malignant pheochromocytoma or hepatic carcinoma. We speculated that any effect may be enhanced by antogonising other signaling pathways. Methods Therefore, we tested the effect of lovastatin—known to inhibit both ERK and AKT signaling—and everolimus, separately and in combination, on cell viability and signaling pathways in human midgut (GOT), pancreatic (BON1), and pulmonary (H727) NET, hepatocellular carcinoma (HepG2, Huh7), and mouse pheochromocytoma (MPC, MTT) cell lines. Results Lovastatin and everolimus separately significantly reduced cell viability in H727, HepG2, Huh7, MPC and MTT cells at clinically relevant doses (P ≤ 0.05). However, high doses of lovastatin were necessary to affect GOT or BON1 cell viability. Clinically relevant doses of both drugs showed additive anti-tumor effects in H727, HepG2, Huh7, MPC and MTT cells (P ≤ 0.05), but not in BON1 or GOT cells. In all cell lines investigated, lovastatin inhibited EGFR and AKT signaling. Subsequently, combination treatment more strongly inhibited EGFR and AKT signaling than everolimus alone, or at least attenuated everolimus-induced EGFR or AKT activation. Vice versa, everolimus constantly decreased pp70S6K and combination treatment more strongly decreased pp70S6K than lovastatin alone, or attenuated lovastatin-induced p70S6K activation: in BON1 cells lovastatin-induced EGFR inhibition was least pronounced, possibly explaining the low efficacy and consequent absent additive effect. Conclusion In summary, clinically relevant doses of lovastatin and everolimus were effective separately and showed additive effects in 5 out of 7 cell lines. Our findings emphasize the importance of targeting several interacting signaling pathways simultaneously when attempting to attenuate tumor growth. However, the variable

  15. Relationship between target antigens and major histocompatibility complex (MHC) class II genes in producing two pathogenic antibodies simultaneously

    PubMed Central

    Zakka, L R; Keskin, D B; Reche, P; Ahmed, A R

    2010-01-01

    In this report, we present 15 patients with histological and immunopathologically proven pemphigus vulgaris (PV). After a mean of 80 months since the onset of disease, when evaluated serologically, they had antibodies typical of PV and pemphigoid (Pg). Similarly, 18 patients with bullous pemphigoid (BP) and mucous membrane pemphigoid (MMP) were diagnosed on the basis of histology and immunopathology. After a mean of 60 months since the onset of disease, when their sera were evaluated they were found to have Pg and PV autoantibodies. In both groups of patients the diseases were characterized by a chronic course, which included several relapses and recurrences and were non-responsive to conventional therapy. The major histocompatibility complex class II (MHC II) genes were studied in both groups of patients and phenotypes associated typically with them were observed. Hence, in 33 patients, two different pathogenic autoantibodies were detected simultaneously. The authors provide a computer model to show that each MHC II gene has relevant epitopes that recognize the antigens associated with both diseases. Using the databases in these computer models, the authors present the hypothesis that these two autoantibodies are produced simultaneously due to the phenomena of epitope spreading. PMID:21069937

  16. Evidence for dose-additive effects of a type II pyrethroid mixture. In vitro assessment.

    PubMed

    Romero, A; Ares, I; Ramos, E; Castellano, V; Martínez, M; Martínez-Larrañaga, M R; Anadón, A; Martínez, M A

    2015-04-01

    Despite the widespread use of pyrethroid insecticides that led to common exposure in the population, few studies have been conducted to quantitatively assess dose-additive effects of pyrethroids using a funcional measure involved in the common toxic mode of action. The aim of this study was to evaluate the potency and efficacy of 6 Type II pyretroids (α-cypermethrin, cyfluthrin, λ-cyhalothrin, deltamethrin, cyphenothrin and esfenvalerate) to evoke induction of both nitric oxide and lipid peroxides levels measured as malondialdehyde in three in vitro models (SH-SY5Y, HepG2 and Caco-2 human cells) as well as to test the hypothesis of dose additivity for mixtures of these same 6 pyrethroids. Concentration-responses for 6 pyrethroids were determined as well as the response to mixtures of all 6 pyrethroids. Additivity was tested assuming a dose-additive model. The human neuroblastoma SH-SY5Y cell line was the most sensitive in vitro model. The rank order of potency for cell SH-SY5Y viability MTT assay was deltamethrin>cyphenothrin>λ-cyhalothrin>cyfluthrin>esfenvalerate>α-cypermethrin. When 6 pyrethroids were present in the mixture at an equitoxic mixing ratio, the action on nitric oxide (NO) and lipid peroxides measured as malondialdehyde (MDA) production was consistent with a dose-additive model. The results of the present study are consistent with previous reports of additivity of pyrethroids in vivo e in vitro. PMID:25688004

  17. Features of quasistable laminar flows of He II and an additional dissipative process

    NASA Astrophysics Data System (ADS)

    Gritsenko, I. A.; Klokol, K. A.; Sokolov, S. S.; Sheshin, G. A.

    2016-03-01

    Quasistable laminar flow of He II at a temperature of 140 mK is studied experimentally. The liquid flow was excited by a vibrating quartz tuning fork with a resonance frequency of about 24 kHz. It was found that for velocities of the tuning fork oscillations from 0.046 to 0.16 m/s, the He II flow can be both quasistable laminar and turbulent. Transitions between these flow regimes were observed. When the velocity of the tuning fork oscillations increases more rapidly, the velocity at which the quasistable flow becomes unstable and undergoes a transition to a turbulent flow is higher. Mechanisms for the dissipation of the energy of the oscillating tines of the tuning fork in the quasistable laminar flow regime are analyzed. It is found that there is an additional mechanism for dissipation of the energy of the oscillating tuning fork beyond internal friction in the quartz. This mechanism is associated with mutual friction owing to scattering of thermal excitations of He II on quantized vortices and leads to a cubic dependence of the exciting force on the fluid velocity.

  18. Proton and Electron Additions to Iron (II) Dinitrogen Complexes Containing Pendant Amines

    SciTech Connect

    Heiden, Zachariah M.; Chen, Shentan; Labios, Liezel AN; Bullock, R. Morris; Walter, Eric D.; Tyson, Elizabeth L.; Mock, Michael T.

    2014-03-10

    We describe a single site cis-(H)FeII-N2 complex, generated by the protonation of an iron-carbon bond of a "reduced" iron complex, that models key aspects of proposed protonated intermediates of the E4 state of nitrogenase. The influence on N2 binding from the addition of protons to the pendant amine sites in the second coordination sphere is described. Furthermore, the addition of electrons to the protonated complexes results in H2 loss. The mechanism of H2 loss is explored to draw a parallel to the origin of H2 loss (homolytic or heterolytic) and the nature of N2 coordination in intermediates of the E4 state of nitrogenase.

  19. Highly efficient simultaneous ultrasonic-assisted adsorption of Pb(II), Cd(II), Ni(II) and Cu (II) ions from aqueous solutions by graphene oxide modified with 2,2'-dipyridylamine: Central composite design optimization.

    PubMed

    Zare-Dorabei, Rouholah; Ferdowsi, Somayeh Moazen; Barzin, Ahmad; Tadjarodi, Azadeh

    2016-09-01

    In present work, a graphene oxide chemically modified with 2,2'-dipyridylamine (GO-DPA), was synthesized by simple, fast and low-cost process for the simultaneous adsorption of four toxic heavy metals, Pb(II), Cd(II), Ni(II) and Cu(II), from aqueous solutions. The synthesized adsorbent was characterized by FT-IR, XRD, XPS, SEM and AFM measurements. The effects of variables such as pH solution, initial ion concentrations, adsorbent dosage and sonicating time were investigated on adsorption efficiency by rotatable central composite design. The optimum conditions, specified as 8mg of adsorbent, 20mgL(-1) of each ion at pH 5 and short time of 4min led to the achievement of a high adsorption capacities. Ultrasonic power had important role in shortening the adsorption time of ions by enhancing the dispersion of adsorbent in solution. The adsorption kinetic studies and equilibrium isotherms for evaluating the mechanism of adsorption process showed a good fit to the pseudo-second order and Langmuir model, respectively. The maximum adsorption capacities (Qm) of this adsorbent were 369.749, 257.201, 180.893 and 358.824mgg(-1) for lead, cadmium, nickel and copper ions, respectively. The removal performance of adsorbent on the real wastewater samples also showed the feasibility of adsorbent for applying in industrial purposes. PMID:27150770

  20. Simultaneous extraction of Cr(VI) and Cu(II) from humic acid with new synthesized EDTA derivatives.

    PubMed

    Zhang, Tao; Wu, Ying-Xin; Huang, Xiong-Fei; Liu, Jun-Min; Xia, Bing; Zhang, Wei-Hua; Qiu, Rong-Liang

    2012-07-01

    Soil washing is one of the few permanent treatment alternatives for removing metal contaminants. Ethylenediaminetetraacetic acid and its salts (EDTA) is very effective at removing cationic metals and has been utilized globally. However it is ineffective for anionic metal contaminants or metals bound to soil organic matter. The simultaneous removal of cationic and anionic metal contaminants by soil washing is difficult due to differences in their properties. The present study evaluated the potential of a washing process using two synthesized EDTA-derivatives, C(6)HEDTA (2,2'-((2-((carboxymethyl)(2-(hexanoyloxy)ethyl)amino)ethyl)azanediyl)diacetic acid) and C(12)HEDTA (2,2'-((2-((carboxymethyl) (2-(dodecanoyloxy)ethyl)amino)ethyl)azanediyl)diacetic acid), which consist of a hydrophilic polycarboxylic moiety and a hydrophobic moiety with a monoalkyl ester group. A series of equilibrium batch experiments at room temperature were conducted to investigate the efficacy of C(6)HEDTA and C(12)HEDTA as extractants for both oxyanion Cr(VI) and cationic Cu(II). Results showed that either C(6)HEDTA or C(12)HEDTA can extract both Cr(VI) and Cu(II) from humic acid simultaneously. However, C(6)HEDTA was less effective for Cr(VI) probably because it has no surface activities to increase solubility of humic acid, like C(12)HEDTA. Extraction of Cr(VI) was mainly attributed to the decreased surface tension and enhanced solubility of organic matter. Extraction of Cu(II) was attributed to both the Cu(II) chelation and enhanced solubility of humic acid. It was demonstrated that the hydrophilic polycarboxylic moiety of C(12)HEDTA chelates cations while the monoalkyl ester group produces surface active properties that enhance the solubility of humic acid. PMID:22555067

  1. Acute and additive toxicity of ten photosystem-II herbicides to seagrass.

    PubMed

    Wilkinson, Adam D; Collier, Catherine J; Flores, Florita; Negri, Andrew P

    2015-01-01

    Photosystem II herbicides are transported to inshore marine waters, including those of the Great Barrier Reef, and are usually detected in complex mixtures. These herbicides inhibit photosynthesis, which can deplete energy reserves and reduce growth in seagrass, but the toxicity of some of these herbicides to seagrass is unknown and combined effects of multiple herbicides on seagrass has not been tested. Here we assessed the acute phytotoxicity of 10 PSII herbicides to the seagrass Halophila ovalis over 24 and/or 48 h. Individual herbicides exhibited a broad range of toxicities with inhibition of photosynthetic activity (∆F/F(m)') by 50% at concentrations ranging from 3.5 μg l(-1) (ametryn) to 132 μg l(-1) (fluometuron). We assessed potential additivity using the Concentration Addition model of joint action for binary mixtures of diuron and atrazine as well as complex mixtures of all 10 herbicides. The effects of both mixture types were largely additive, validating the application of additive effects models for calculating the risk posed by multiple PSII herbicides to seagrasses. This study extends seagrass ecotoxicological data to ametryn, metribuzin, bromacil, prometryn and fluometuron and demonstrates that low concentrations of PSII herbicide mixtures have the potential to impact ecologically relevant endpoints in seagrass, including ∆F/F(m)'. PMID:26616444

  2. Acute and additive toxicity of ten photosystem-II herbicides to seagrass

    PubMed Central

    Wilkinson, Adam D.; Collier, Catherine J.; Flores, Florita; Negri, Andrew P.

    2015-01-01

    Photosystem II herbicides are transported to inshore marine waters, including those of the Great Barrier Reef, and are usually detected in complex mixtures. These herbicides inhibit photosynthesis, which can deplete energy reserves and reduce growth in seagrass, but the toxicity of some of these herbicides to seagrass is unknown and combined effects of multiple herbicides on seagrass has not been tested. Here we assessed the acute phytotoxicity of 10 PSII herbicides to the seagrass Halophila ovalis over 24 and/or 48 h. Individual herbicides exhibited a broad range of toxicities with inhibition of photosynthetic activity (∆F/Fm′) by 50% at concentrations ranging from 3.5 μg l−1 (ametryn) to 132 μg l−1 (fluometuron). We assessed potential additivity using the Concentration Addition model of joint action for binary mixtures of diuron and atrazine as well as complex mixtures of all 10 herbicides. The effects of both mixture types were largely additive, validating the application of additive effects models for calculating the risk posed by multiple PSII herbicides to seagrasses. This study extends seagrass ecotoxicological data to ametryn, metribuzin, bromacil, prometryn and fluometuron and demonstrates that low concentrations of PSII herbicide mixtures have the potential to impact ecologically relevant endpoints in seagrass, including ∆F/Fm′. PMID:26616444

  3. Acute and additive toxicity of ten photosystem-II herbicides to seagrass

    NASA Astrophysics Data System (ADS)

    Wilkinson, Adam D.; Collier, Catherine J.; Flores, Florita; Negri, Andrew P.

    2015-11-01

    Photosystem II herbicides are transported to inshore marine waters, including those of the Great Barrier Reef, and are usually detected in complex mixtures. These herbicides inhibit photosynthesis, which can deplete energy reserves and reduce growth in seagrass, but the toxicity of some of these herbicides to seagrass is unknown and combined effects of multiple herbicides on seagrass has not been tested. Here we assessed the acute phytotoxicity of 10 PSII herbicides to the seagrass Halophila ovalis over 24 and/or 48 h. Individual herbicides exhibited a broad range of toxicities with inhibition of photosynthetic activity (∆F/Fm‧) by 50% at concentrations ranging from 3.5 μg l-1 (ametryn) to 132 μg l-1 (fluometuron). We assessed potential additivity using the Concentration Addition model of joint action for binary mixtures of diuron and atrazine as well as complex mixtures of all 10 herbicides. The effects of both mixture types were largely additive, validating the application of additive effects models for calculating the risk posed by multiple PSII herbicides to seagrasses. This study extends seagrass ecotoxicological data to ametryn, metribuzin, bromacil, prometryn and fluometuron and demonstrates that low concentrations of PSII herbicide mixtures have the potential to impact ecologically relevant endpoints in seagrass, including ∆F/Fm‧.

  4. Simultaneous Radio and EUV Imaging of a Multi-lane Coronal Type II Radio Burst

    NASA Astrophysics Data System (ADS)

    Feng, S. W.; Du, G. H.; Chen, Y.; Kong, X. L.; Li, G.; Guo, F.

    2015-04-01

    A multi-lane solar type II radio burst was observed by several solar spectrographs on 16 February 2011. The event was also recorded by the Nançay Radioheliograph (NRH) at several metric wavelengths, by the Atmospheric Imaging Assembly (AIA) onboard the Solar Dynamics Observatory (SDO), and by the Extreme Ultraviolet Imager (EUVI) onboard the Solar TErrestrial Relations Observatory (STEREO) in a number of EUV passbands. These multi-wavelength data provide a rare opportunity to reveal the emission source of the multiple type II lanes. Our study shows that all lanes are associated with a single EUV wave, presumably the radio-emitting shock. The EUV wave was driven by a coronal mass ejection (CME) associated with an M1.6 flare and a filament eruption. With the NRH data and the three-dimensional (3D) bow-shock reconstruction that we built using the multi-viewpoint data of the EUV wave, we are able to deduce the 3D coordinates of the radio sources. We conclude that all the three type II lanes originated from the western flank of the shock, with two of them from closely adjacent locations on the southern part, the other one from a distinct location on the northern part. This case study demonstrates how the type II origin can be pinpointed by combining analyses of different data sets.

  5. Simultaneous determination of chromium(III), aluminum(III), and iron(II) in tannery sludge acid extracts by reversed-phase high-performance liquid chromatography

    SciTech Connect

    Lopez, A.; Passino, R.; Tiravanti, G. ); Rotunno, T.; Palmisano, F.; Zambonin, P.G. )

    1991-07-01

    A new chromatographic method for the simultaneous determination of Cu(II), Zn(II), Cr(III), Al(III), and Fe(III) or Fe(II) has been developed. The method is based on precolumn formation of stable metal-8-hydroxyquinoline chelates, their separation on a C-18 reversed-phase column by HPLC, and their UV-vis detection at 400 nm. The experimental conditions giving the highest chelate yields resulted: pH 4.2; T = 90C; reaction time 30 min; reaction mixture composition methanol (66.7%)/acetonitrile (13.3%)/water (20%) (v/v/v) plus 10 mM 8-hydroxyquinoline. The mobile-phase composition giving the best resolution of Cr(III)- and Al(III)-8-hydroxyquinoline chromatographic peaks has been optimized by the simplex algorithm: acetonitrile (13.5%)/methanol (29%)/0.1 acetate buffer pH 6.8 (13.5%) (v/v/v) plus 100 mM 8-hydroxyquinoline. The method has been applied to synthetic solutions as well as, after sample pretreatment on XAD-7 resin, to real sulfuric acid extracts of tannery sludges. As for this latter matrix, additional information on Cr and Fe oxidation states has been obtained, combining the proposed method with atomic absorption spectroscopy and ion chromatography.

  6. Simultaneous measurement of thermal diffusivity and optical absorption coefficient using photothermal radiometry. II Multilayered solids

    NASA Astrophysics Data System (ADS)

    Salazar, Agustín; Fuente, Raquel; Apiñaniz, Estibaliz; Mendioroz, Arantza; Celorrio, R.

    2011-08-01

    The aim of this work is to analyze the ability of modulated photothermal radiometry to retrieve the thermal diffusivity and the optical absorption coefficient of layered materials simultaneously. First, we extend the thermal quadrupole method to calculate the surface temperature of semitransparent multilayered materials. Then, this matrix method is used to evaluate the influence of heat losses by convection and radiation, the influence of the use of thin paint layers on the accuracy of thermal diffusivity measurements, and the effect of lateral heat diffusion due to the use of Gaussian laser beams. Finally, we apply the quadrupole method to retrieve (a) the thermal contact resistance in glass stacks and (b) the thermal diffusivity and optical absorption coefficient depth profiles in heterogeneous materials with continuously varying physical properties, as is the case of functionally graded materials and partially cured dental resins.

  7. Simultaneous and differential fronto-orbital and midface distraction osteogenesis for syndromic craniosynostosis using rigid external distractor II.

    PubMed

    Medra, Ahmed Mohamed; Marei, Ahmed Gaber; Shehata, Ehab Ali; McGurk, Mark; Habib, Ahmed

    2012-09-01

    In syndromic craniosynostosis, the relation between the supraorbital area and the frontal bone is not good, and it is not possible to reform this area with 1-block advancement. To avoid this problem, the frontal bone is separated from the fronto-orbital bandeau, each is reshaped and remodeled separately, and then both are reattached. The retrusion of the midface, especially in syndromic craniosynostosis, is usually greater than that of cranial bones, so the technique usually separating the midface from the cranium is Le Fort III osteotomy, which allows differential distraction of each part. In this procedure, the cranial and midfacial bones are advanced simultaneously and differentially, both to the planned extent, in a single-stage operation, using rigid external distractor II, correcting exorbitism, respiratory embarrassment, and cranial structures and avoiding eye complications in the future. This procedure was used, with a follow-up, in 10 patients with syndromic craniosynostosis from 2 to 5 years. PMID:22976628

  8. A Fully Nonmetallic Gas Turbine Engine Enabled by Additive Manufacturing, Part II: Additive Manufacturing and Characterization of Polymer Composites

    NASA Technical Reports Server (NTRS)

    Chuang, Kathy C.; Grady, Joseph E.; Arnold, Steven M.; Draper, Robert D.; Shin, Eugene; Patterson, Clark; Santelle, Tom; Lao, Chao; Rhein, Morgan; Mehl, Jeremy

    2015-01-01

    This publication is the second part of the three part report of the project entitled "A Fully Nonmetallic Gas Turbine Engine Enabled by Additive Manufacturing" funded by NASA Aeronautics Research Institute (NARI). The objective of this project was to conduct additive manufacturing to produce aircraft engine components by Fused Deposition Modeling (FDM), using commercially available polyetherimides-Ultem 9085 and experimental Ultem 1000 mixed with 10% chopped carbon fiber. A property comparison between FDM-printed and injection molded coupons for Ultem 9085, Ultem 1000 resin and the fiber-filled composite Ultem 1000 was carried out. Furthermore, an acoustic liner was printed from Ultem 9085 simulating conventional honeycomb structured liners and tested in a wind tunnel. Composite compressor inlet guide vanes were also printed using fiber-filled Ultem 1000 filaments and tested in a cascade rig. The fiber-filled Ultem 1000 filaments and composite vanes were characterized by scanning electron microscope (SEM) and acid digestion to determine the porosity of FDM-printed articles which ranged from 25 to 31%. Coupons of Ultem 9085, experimental Ultem 1000 composites and XH6050 resin were tested at room temperature and 400F to evaluate their corresponding mechanical properties. A preliminary modeling was also initiated to predict the mechanical properties of FDM-printed Ultem 9085 coupons in relation to varied raster angles and void contents, using the GRC-developed MAC/GMC program.

  9. NEAR-SIMULTANEOUS OBSERVATIONS OF X-RAY PLASMA EJECTION, CORONAL MASS EJECTION, AND TYPE II RADIO BURST

    SciTech Connect

    Kim, Yeon-Han; Bong, Su-Chan; Park, Y.-D.; Cho, K.-S.; Moon, Y.-J.

    2009-11-10

    We report the first simultaneous observation of X-ray plasma ejection (XPE), coronal mass ejection (CME), and type II solar radio burst on 1999 October 26. First, an XPE was observed from 21:12 UT to 21:24 UT in the Yohkoh SXT field of view (1.1 to 1.4 R{sub sun}). The XPE was accelerated with a speed range from 190 to 410 km s{sup -1} and its average speed is about 290 km s{sup -1}. Second, the associated CME was observed by the Mauna Loa Mk4 coronameter (1.1-2.8 R{sub sun}) from 21:16 UT. The CME front was clearly identified at 21:26 UT and propagated with a deceleration of about -110 m s{sup -2}. Its average speed is about 360 km s{sup -1}. At the type II burst start time (21:25 UT), the height of the CME front is around 1.7 R{sub sun} and its speed is about 470 km s{sup -1}. Third, a type II solar radio burst was observed from 21:25 UT to 21:43 UT by the Culgoora solar radio spectrograph. The burst shows three emission patches during this observing period and the emission heights of the burst are estimated to be about 1.3 R{sub sun} (21:25 UT), 1.4 R{sub sun} (21:30 UT), and 1.8 R{sub sun} (21:40 UT). By comparing these three phenomena, we find that: (1) kinematically, while the XPE shows acceleration, the associated CME front shows deceleration; (2) there is an obvious height difference (0.3 R {sub sun}) between the CME front and the XPE front around 21:24 UT and the formation height of the type II burst is close to the trajectory extrapolated from the XPE front; (3) both speeds of the XPE and the CME are comparable with each other around the starting time of the type II burst. Considering the formation height and the speed of the type II burst, we suggest that its first emission is due to the coronal shock generated by the XPE and the other two emissions are driven by the CME flank interacting with the high-density streamer.

  10. The First measurement of the top quark mass at CDF II in the lepton+jets and dilepton channels simultaneously

    SciTech Connect

    Aaltonen, T.; Adelman, J.; Akimoto, T.; Albrow, Michael G.; Alvarez Gonzalez, B.; Amerio, S.; Amidei, Dante E.; Anastassov, A.; Annovi, Alberto; Antos, J.; Apollinari, G.; /Fermilab /Purdue U.

    2008-09-01

    The authors present a measurement of the mass of the top quark using data corresponding to an integrated luminosity of 1.9 fb{sup -1} of p{bar p} collisions collected at {radical}s = 1.96 TeV with the CDF II detector at Fermilab's Tevatron. This is the first measurement of the top quark mass using top-antitop pair candidate events in the lepton + jets and dilepton decay channels simultaneously. They reconstruct two observables in each channel and use a non-parametric kernel density estimation technique to derive two-dimensional probability density functions from simulated signal and background samples. The observables are the top quark mass and the invariant mass of two jets from the W decay in the lepton + jets channel, and the top quark mass and the scalar sum of transverse energy of the event in the diletpon channel. They perform a simultaneous fit for the top quark mass and the jet energy scale, which is constrained in situ by the hadronic W boson mass. using 332 lepton + jets candidate events and 144 diletpon candidate events, they measure the top quark mass to be m{sub top} = 171.9 {+-} 1.7 (stat. + JES) {+-} 1.1 (other sys.) GeV/c{sup 2} = 171.9 {+-} 2.0 GeV/c{sup 2}.

  11. Appropriate Fe (II) Addition Significantly Enhances Anaerobic Ammonium Oxidation (Anammox) Activity through Improving the Bacterial Growth Rate

    PubMed Central

    Liu, Yiwen; Ni, Bing-Jie

    2015-01-01

    The application of anaerobic ammonium oxidation (Anammox) process is often limited by the slow growth rate of Anammox bacteria. As the essential substrate element that required for culturing Anammox sludge, Fe (II) is expected to affect Anammox bacterial growth. This work systematically studied the effects of Fe (II) addition on Anammox activity based on the kinetic analysis of specific growth rate using data from batch tests with an enriched Anammox sludge at different dosing levels. Results clearly demonstrated that appropriate Fe (II) dosing (i.e., 0.09 mM) significantly enhanced the specific Anammox growth rate up to 0.172 d−1 compared to 0.118 d−1 at regular Fe (II) level (0.03 mM). The relationship between Fe (II) concentration and specific Anammox growth rate was found to be well described by typical substrate inhibition kinetics, which was integrated into currently well-established Anammox model to describe the enhanced Anammox growth with Fe (II) addition. The validity of the integrated Anammox model was verified using long-term experimental data from three independent Anammox reactors with different Fe (II) dosing levels. This Fe (II)-based approach could be potentially implemented to enhance the process rate for possible mainstream application of Anammox technology, in order for an energy autarchic wastewater treatment. PMID:25644239

  12. Appropriate Fe (II) Addition Significantly Enhances Anaerobic Ammonium Oxidation (Anammox) Activity through Improving the Bacterial Growth Rate

    NASA Astrophysics Data System (ADS)

    Liu, Yiwen; Ni, Bing-Jie

    2015-02-01

    The application of anaerobic ammonium oxidation (Anammox) process is often limited by the slow growth rate of Anammox bacteria. As the essential substrate element that required for culturing Anammox sludge, Fe (II) is expected to affect Anammox bacterial growth. This work systematically studied the effects of Fe (II) addition on Anammox activity based on the kinetic analysis of specific growth rate using data from batch tests with an enriched Anammox sludge at different dosing levels. Results clearly demonstrated that appropriate Fe (II) dosing (i.e., 0.09 mM) significantly enhanced the specific Anammox growth rate up to 0.172 d-1 compared to 0.118 d-1 at regular Fe (II) level (0.03 mM). The relationship between Fe (II) concentration and specific Anammox growth rate was found to be well described by typical substrate inhibition kinetics, which was integrated into currently well-established Anammox model to describe the enhanced Anammox growth with Fe (II) addition. The validity of the integrated Anammox model was verified using long-term experimental data from three independent Anammox reactors with different Fe (II) dosing levels. This Fe (II)-based approach could be potentially implemented to enhance the process rate for possible mainstream application of Anammox technology, in order for an energy autarchic wastewater treatment.

  13. Improved sensing using simultaneous deep-UV Raman and fluorescence detection-II

    NASA Astrophysics Data System (ADS)

    Hug, W. F.; Bhartia, R.; Sijapati, K.; Beegle, L. W.; Reid, R. D.

    2014-05-01

    Photon Systems in collaboration with JPL is continuing development of a new technology robot-mounted or hand-held sensor for reagentless, short-range, standoff detection and identification of trace levels chemical, biological, and explosive (CBE) materials on surfaces. This deep ultraviolet CBE sensor is the result of Army STTR and DTRA programs. The evolving 10 to 15 lb, 20 W, sensor can discriminate CBE from background clutter materials using a fusion of deep UV excited resonance Raman (RR) and laser induced native fluorescence (LINF) emissions collected is less than 1 ms. RR is a method that provides information about molecular bonds, while LINF spectroscopy is a much more sensitive method that provides information regarding the electronic configuration of target molecules. Standoff excitation of suspicious packages, vehicles, persons, and other objects that may contain hazardous materials is accomplished using excitation in the deep UV where there are four main advantages compared to near-UV, visible or near-IR counterparts. 1) Excited between 220 and 250 nm, Raman emission occur within a fluorescence-free region of the spectrum, eliminating obscuration of weak Raman signals by fluorescence from target or surrounding materials. 2) Because Raman and fluorescence occupy separate spectral regions, detection can be done simultaneously, providing an orthogonal set of information to improve both sensitivity and lower false alarm rates. 3) Rayleigh law and resonance effects increase Raman signal strength and sensitivity of detection. 4) Penetration depth into target in the deep UV is short, providing spatial/spectral separation of a target material from its background or substrate. 5) Detection in the deep UV eliminates ambient light background and enable daylight detection.

  14. 40 CFR 82.18 - Availability of production in addition to baseline production allowances for class II controlled...

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ....20 in order to produce with the additional production allowances. (2) Trade from a Party—Information... 40 Protection of Environment 17 2010-07-01 2010-07-01 false Availability of production in addition to baseline production allowances for class II controlled substances. 82.18 Section 82.18...

  15. Structure of microbial communities performing the simultaneous reduction of Fe(II)EDTA.NO2- and Fe(III)EDTA -.

    PubMed

    Kumaraswamy, Rajkumari; Kuenen, J Gijs; Kleerebezem, Robbert; van Loosdrecht, Mark C M; Muyzer, Gerard

    2006-12-01

    BioDeNOx is a combined physicochemical and biological process for the removal of nitrogen oxides (NOx) from flue gas. In the present study, two anaerobic bioreactors performing BioDeNOx were run consecutively (RUN-1 and RUN-2) at a dilution rate of 0.01 h(-1) with Fe(II)EDTA.NO(2-) and Fe(III)EDTA(-) as electron acceptors and ethanol as electron donor. The measured protein concentration of the reactor biomass of both runs was 120 mg/l. Different molecular methods were used to determine the identity and abundance of the bacterial populations in both bioreactors. Bacillus azotoformans strain KT-1 was recognized as a key player in Fe(II)EDTA.NO(2-) reduction. PCR-denaturing gradient gel electrophoresis analysis of the reactor biomass showed a greater diversity in RUN-2 than in RUN-1. Enrichments of Fe(II)EDTA.NO(2-) and Fe(III)EDTA(-) reducers and activity assays were conducted using the biomass from RUN-2 as an inoculum. The results on substrate turnover, overall microbial diversity, and enrichments and finally activity assays confirmed that ethanol was used as electron donor for Fe(II)EDTA.NO(2-) reduction. In addition, the Fe(III)EDTA(-) reduction rate of the microbial community proved to be feasible enough to run the bioreactors, ruling out the chemical reduction of Fe(III)EDTA(-) with sulfide as was proposed by other researchers. PMID:16957895

  16. Effects of Silica Nanoparticle Supported Ionic Liquid as Additive on Thermal Reversibility of Human Carbonic Anhydrase II

    PubMed Central

    Fallahbagheri, Azadeh; Saboury, Ali Akbar; Ma'mani, Leila; Taghizadeh, Mohammad; Khodarahmi, Reza; Ranjbar, Samira; Bohlooli, Mousa; Shafiee, Abbas; Foroumadi, Alireza; Sheibani, Nader; Moosavi-Movahedi, Ali Akbar

    2013-01-01

    Silica nanoparticle supported imidazolium ionic liquid [SNImIL] was synthesized and utilized as a biocompatible additive for studying the thermal reversibility of human carbonic anhydrase II (HCA II). For this purpose, we prepared additive by modification of nanoparticles through the grafting of ionic liquids on the surface of nanoparticles (SNImIL). The SNImIL were fully characterized by Fourier Transform Infrared spectroscopy, scanning electron microscopy and thermo gravimetric analysis. The characterization of HCA II was investigated by various techniques including UV–Vis and ANS fluorescence spectrophotometry, differential scanning calorimetry, and docking study. SNImIL induced disaggregation, enhanced protein stability and increased thermal reversibility of HCA II by up to 42% at pH 7.75. PMID:22829053

  17. Effect of the simultaneous addition of beta-cyclodextrin and the herbicide norflurazon on its adsorption and movement in soils.

    PubMed

    Villaverde, Jaime; Maqueda, Celia; Morillo, Esmeralda

    2006-06-28

    The effects of beta-cyclodextrin (BCD) on the sorption-desorption and transport processes of the herbicide norflurazon (NFL) in soils of different characteristics when both are applied simultaneously have been investigated. Adsorption-desorption studies of NFL on six soils of very different characteristics in the presence of BCD have been performed using a batch equilibration method and correlated to its mobility in homogeneous hand-packed soil columns. NFL determinations were undertaken by HPLC equipped with a diode array detector at a wavelength of 220 nm. BCD was also analyzed by HPLC with fluorimetric detection using a postcolumn reaction. The interaction of NFL with BCD yielded the formation of an inclusion complex in solution. When this complex is applied to soils, a large decrease in NFL adsorption capacity and an increase in its desorption were observed, due to the higher tendency of NFL-BCD complexes to remain in solution. The results obtained in adsorption and soil column experiments indicated that the influence of BCD on NFL mobility and availability depends on the different affinities of BCD to be sorbed on soils of different characteristics and on the concentration of BCD used. The lower the concentration of BCD added, the more tenaciously it adheres to the soil, and most of the BCD molecules would be adsorbed, providing a coating to soil particles that acts as a bridge between NFL and the soil surface, acting as an adsorbent and retarding the mobility of the herbicide. At higher concentrations of BCD, or in soils where its adsorption is very low, most of the BCD molecules are in the aqueous phase and NFL molecules tend to be complexed with BCD in solution, acting then as a solubilizing agent. PMID:16787026

  18. Simultaneous Oxidization of NOx and SO2 by a New Non-thermal Plasma Reactor Enhanced by Catalyst and Additive

    NASA Astrophysics Data System (ADS)

    Kim, Heejoon; Jun, Han; Sakaguchi, Yuhei; Minami, Wataru

    2008-02-01

    The non-thermal plasma as one of the most promising technologies for removing NOx and SO2 has attracted much attention. In this study, a new plasma reactor combined with catalyst and additive was developed to effectively oxidize and remove NOx and SO2 in the flue gas. The experimental results showed that TiO2 could improve the oxidation efficiency of SO2 in the case of applying plasma while having a negative effect on the oxidation process of NO and NOx. With the addition of NH3, the oxidation rates of NOx, NO and SO2 were slightly increased. However, the effect of adding NH3 on NOx oxidation was negative when the temperature was above 200°C.

  19. Radiation dose escalation by simultaneous modulated accelerated radiotherapy combined with chemotherapy for esophageal cancer: a phase II study

    PubMed Central

    Zhai, Tiantian; Chang, Daniel; Chen, Zhijian; Huang, Ruihong; Zhang, Wuzhe; Lin, Kun; Guo, Longjia; Zhou, Mingzhen; Li, Dongsheng; Li, Derui; Chen, Chuangzhen

    2016-01-01

    The outcomes for patients with esophageal cancer (EC) underwent standard-dose radical radiotherapy were still disappointing. This phase II study investigated the feasibility, safety and efficacy of radiation dose escalation using simultaneous modulated accelerated radiotherapy (SMART) combined with chemotherapy in 60 EC patients. Radiotherapy consisted of 66Gy at 2.2 Gy/fraction to the gross tumor and 54Gy at 1.8 Gy/fraction to subclinical diseases simultaneously. Chemotherapy including cisplatin and 5fluorouracil were administered to all patients during and after radiotherapy. The data showed that the majority of patients (98.3%) completed the whole course of radiotherapy and concurrent chemotherapy. The most common ≥ grade 3 acute toxicities were neutropenia (16.7%), followed by esophagitis (6.7%) and thrombopenia (5.0%). With a median follow-up of 24 months (5-38) for all patients and 30 months (18-38) for those still alive, 11 patients (18.3%) developed ≥ Grade 3 late toxicities and 2 (3.3%) of them died subsequently due to esophageal hemorrhage. The 1- and 2-year local-regional control, distant metastasis-free survival, disease-free survival and overall survival rates were 87.6% and 78.6%, 86.0% and 80.5%, 75.6% and 64.4%, 86.7% and 72.7%, respectively. SMART combined with concurrent chemotherapy is feasible in EC patients with tolerable acute toxicities. They showed a trend of significant improvements in local-regional control and overall survival. Further follow-up is needed to evaluate the late toxicities. PMID:26992206

  20. [Simultaneous rapid determination of eight food additives in foods by reversed-phase high performance liquid chromatography].

    PubMed

    Zhang, X Y

    2000-11-01

    A simple and rapid method for the determination of eight food additives by RP-HPLC is described. They were saccharin, aspartame, benzoic acid, sorbic acid, vanillin, caffeine, carmine and sunset yellow. The experiments were carried on Shim-pack CLC-ODS (150 mm x 6.0 mm i.d.) with methanol-20 mmol/L NH4Ac (44:56, V/V; pH 7.0) as the eluent at a flow rate of 1.0 mL/min. The UV detection wavelength was fixed at 220 nm. The food samples, after precipitation of the impurities with Carrez reagent, were injected directly into the HPLC system. The average recoveries of all the eight additives were between 91.9%-108.5%, and the RSDs were lower than 4% (n = 5). The analysis of a single sample required only 8 min. This method has been successfully applied to the routine analysis of these additives in foods. PMID:12541745

  1. Evidence from simultaneous intracellular- and surface-pH transients that carbonic anhydrase II enhances CO2 fluxes across Xenopus oocyte plasma membranes

    PubMed Central

    Occhipinti, Rossana; Boron, Walter F.

    2014-01-01

    The α-carbonic anhydrases (CAs) are zinc-containing enzymes that catalyze the interconversion of CO2 and HCO3−. Here, we focus on human CA II (CA II), a ubiquitous cytoplasmic enzyme. In the second paper in this series, we examine CA IV at the extracellular surface. After microinjecting recombinant CA II in a Tris solution (or just Tris) into oocytes, we expose oocytes to 1.5% CO2/10 mM HCO3−/pH 7.50 while using microelectrodes to monitor intracellular pH (pHi) and surface pH (pHS). CO2 influx causes the familiar sustained pHi fall as well as a transient pHS rise; CO2 efflux does the opposite. Both during CO2 addition and removal, CA II increases the magnitudes of the maximal rate of pHi change, (dpHi/dt)max, and the maximal change in pHS, ΔpHS. Preincubating oocytes with the inhibitor ethoxzolamide eliminates the effects of CA II. Compared with pHS, pHi begins to change only after a delay of ∼9 s and its relaxation has a larger (i.e., slower) time constant (τpHi > τpHS). Simultaneous measurements with two pHi electrodes, one superficial and one deep, suggest that impalement depth contributes to pHi delay and higher τpHi. Using higher CO2/HCO3− levels, i.e., 5%/33 mM HCO3− or 10%/66 mM HCO3−, increases (dpHi/dt)max and ΔpHS, though not in proportion to the increase in [CO2]. A reaction-diffusion mathematical model (described in the third paper in this series) accounts for the above general features and supports the conclusion that cytosolic CA—consuming entering CO2 or replenishing exiting CO2—increases CO2 fluxes across the cell membrane. PMID:24965587

  2. Fast and simultaneous determination of eleven synthetic color additives in flour and meat products by liquid chromatography coupled with diode-array detector and tandem mass spectrometry.

    PubMed

    Qi, Ping; Lin, Zi-hao; Chen, Gui-yun; Xiao, Jian; Liang, Zhi-an; Luo, Li-ni; Zhou, Jun; Zhang, Xue-wu

    2015-08-15

    In this study, an efficient, fast and sensitive method for the simultaneous determination of eleven synthetic color additives (Allura red, Amaranth, Azo rubine, Brilliant blue, Erythrosine, Indigotine, Ponceau 4R, New red, Sunset yellow, Quinoline yellow and Tartrazine) in flour and meat foodstuffs is developed and validated using HPLC coupled with DAD and MS/MS. The color additives were extracted with ammonia-methanol and was further purified with SPE procedure using Strata-AW column in order to reduce matrix interference. This HPLC-DAD method is intended for a comprehensive survey of color additives in foods. HPLC-MS/MS method was used as the further confirmation and identification. Validation data showed the good recoveries in the range of 75.2-113.8%, with relative standard deviations less than 15%. These methods are suitable for the routine monitoring analysis of eleven synthetic color additives due to its sensitivity, reasonable time and cost. PMID:25794727

  3. Simultaneous extraction of flavonoids from Chamaecyparis obtusa using deep eutectic solvents as additives of conventional extractions solvents.

    PubMed

    Tang, Baokun; Park, Ha Eun; Row, Kyung Ho

    2015-01-01

    Three flavones (quercetin, myricetin and amentoflavone) were extracted from Chamaecyparis obtusa leaves using deep eutectic solvents (DESs) as additives to conventional extractions solvents. Sixteen DESs were synthesized from different salts and hydrogen bond donors. In addition, C. obtusa was extracted under optimal conditions of methanol as the solvent in the heating process (60°C) for 120 min at a solid/liquid ratio of 80%. Under these optimal conditions, a good linear relationship was observed at analyte concentrations ranging from 5.0 to 200.0 μg/mL (R(2) > 0.999). The extraction recovery ranged from 96.7 to 103.3% with the inter- and intraday relative standard deviations of <4.97%. Under the optimal conditions, from C. obtusa, the quantities of quercetin, myricetin and amentoflavone extracted were 325.90, 8.66 and 50.34 µg/mL, respectively. Overall, DESs are expected to have a wide range of applications. PMID:25228687

  4. Effectively simultaneous naked-eye detection of Cu(II), Pb(II), Al(III) and Fe(III) using cyanidin extracted from red cabbage as chelating agent

    NASA Astrophysics Data System (ADS)

    Khaodee, Warangkhana; Aeungmaitrepirom, Wanlapa; Tuntulani, Thawatchai

    Simultaneous determination of Cu(II), Pb(II), Al(III) and Fe(III) using cyanidin as a chelating agent was investigated in terms of both quantitative and qualitative detections. Cyanidin was extracted and purified from red cabbage which is a local plant in Thailand. The selectivity of this method was examined by regulating the pH of cyanidin solution operated together with masking agents. It was found that Cu(II), Pb(II), Al(III) and Fe(III) simultaneously responded with the color change at pH 7, pH 6, pH 5 and pH 4, respectively. KF, DMG and the mixture of KF and DMG were used as masking agents for the determination of Fe(III), Al(III) and Pb(II), respectively. Results from naked-eye detection were evaluated by comparing with those of inductively coupled plasma (ICP), and there was no significant difference noticed. Cyanidin using as a multianalyte reagent could be employed for simultaneous determination of Cu(II), Pb(II), Al(III) and Fe(III) at the lowest concentration at 50, 80, 50 and 200 μM, respectively, by slightly varying pHs. Moreover, the proposed method could be potentially applied for real water samples with simplicity, rapidity, low cost and environmental safety.

  5. 40 CFR 82.18 - Availability of production in addition to baseline production allowances for class II controlled...

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 18 2013-07-01 2013-07-01 false Availability of production in addition to baseline production allowances for class II controlled substances. 82.18 Section 82.18 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) PROTECTION OF STRATOSPHERIC OZONE Production and...

  6. 40 CFR 82.18 - Availability of production in addition to baseline production allowances for class II controlled...

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 18 2012-07-01 2012-07-01 false Availability of production in addition to baseline production allowances for class II controlled substances. 82.18 Section 82.18 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) PROTECTION OF STRATOSPHERIC OZONE Production and...

  7. Influence of the simultaneous addition of bentonite and cellulose fibers on the mechanical and barrier properties of starch composite-films.

    PubMed

    de Moraes, J Oliveira; Müller, C M O; Laurindo, J B

    2012-02-01

    The addition of nanoclay or cellulose fibers has been presented in the literature as a suitable alternative for reinforcing starch films. The aim of the present work was to evaluate the effect of the simultaneous incorporation of nanoclay (bentonite) and cellulose fibers on the mechanical and water barrier properties of the resultant composite-films. Films were prepared by casting with 3% in weight of cassava starch, using glycerol as plasticizer (0.30 g per g of starch), cellulose fibers at a concentration of 0.30 g of fibers per g of starch and nanoclay (0.05 g clay per g starch and 0.10 g clay per g starch). The addition of cellulose fibers and nanoclay increased the tensile strength of the films 8.5 times and the Young modulus 24 times but reduced the elongation capacity 14 times. The water barrier properties of the composite-films to which bentonite and cellulose fibers were added were approximately 60% inferior to those of starch films. Diffractograms showed that the nanoclay was intercalated in the polymeric matrix. These results indicate that the simultaneous addition of bentonite and cellulose fibers is a suitable alternative to increase the tensile strength of the films and decrease their water vapor permeabilities. PMID:22049161

  8. An Experimental Evaluation of Hyperactivity and Food Additives. 1977-Phase II.

    ERIC Educational Resources Information Center

    Harley, J. Preston; And Others

    Phase II of a study on the effectiveness of B. Feingold's recommended diet for hyperactive children involved the nine children (mean age 9 years) who had shown the "best" response to diet manipulation in Phase I. Each child served as his own control and was challenged with specified amounts of placebo and artificial color containing food items…

  9. Influence of polymer additives on turbulence in von Karman swirling flow between two disks. II

    NASA Astrophysics Data System (ADS)

    Burnishev, Yuri; Steinberg, Victor

    2016-03-01

    We present the experimental studies of the influence of polymer additives on the statistical and scaling properties of the fully developed turbulent regime in a von Karman swirling flow driven either by the smooth or bladed disks using only the global measurements of torque Γ and pressure p fluctuations in water- and water-sugar-based solutions of different viscosities, or elasticity El, and different polymer concentrations ϕ as a function of Re in the same apparatus. There are three highlights achieved and reported in the paper: (i) An observation of turbulent drag reduction (TDR) at both the inertial and viscous flow forcing, in a contradiction to a currently accepted opinion that only the viscous forcing leads to TDR, and the unexpected drastic difference in the transition to the fully developed turbulent and TDR regimes in von Karman swirling flow of water-based polymer solutions depending on the way of the forcing; (ii) a continuous transition to TDR in both the normalized torque drop and the rms pressure fluctuations drop and universality in scaling behavior of Cf in an agreement with theoretical predictions; and (iii) the dramatic differences in the appearance of the frequency power spectra of Γ and in particular p due to the different ways of the forcing are also observed. We discuss and summarize further the results in accordance with these three main achievements. The main message of these studies is that both the inertial forcing and viscous forcing of von Karman swirling flow between two counter-rotating disks lead to TDR in the sharp contrast to the currently accepted opinion [O. Cadot et al., "Turbulent drag reduction in a closed flow system: Boundary layer versus bulk effects," Phys. Fluids 10, 426 (1998); D. Bonn et al., "From scale scales to large scales in three-dimensional turbulence: The effect of diluted polymers," Phys. Rev. E 47, R28 (1993); and D. Bonn et al., "Turbulent drag reduction by polymers," J. Phys.: Condens. Matter 17, S1195

  10. Treatment of nasopharyngeal carcinoma using simultaneous modulated accelerated radiation therapy via helical tomotherapy: a phase II study

    PubMed Central

    Du, Lei; Zhang, Xin Xin; Feng, Lin Chun; Chen, Jing; Yang, Jun; Liu, Hai Xia; Xu, Shou Ping; Xie, Chuan Bin

    2016-01-01

    Abstract Background The aim of the study was to evaluate short-term safety and efficacy of simultaneous modulated accelerated radiation therapy (SMART) delivered via helical tomotherapy in patients with nasopharyngeal carcinoma (NPC). Methods Between August 2011 and September 2013, 132 newly diagnosed NPC patients were enrolled for a prospective phase II study. The prescription doses delivered to the gross tumor volume (pGTVnx) and positive lymph nodes (pGTVnd), the high risk planning target volume (PTV1), and the low risk planning target volume (PTV2), were 67.5 Gy (2.25 Gy/F), 60 Gy (2.0 Gy/F), and 54 Gy (1.8 Gy/F), in 30 fractions, respectively. Acute toxicities were evaluated according to the established RTOG/EORTC criteria. This group of patients was compared with the 190 patients in the retrospective P70 study, who were treated between September 2004 and August 2009 with helical tomotherapy, with a dose of 70-74 Gy/33F/6.5W delivered to pGTVnx and pGTVnd. Results The median follow-up was 23.7 (12–38) months. Acute radiation related side-effects were mainly problems graded as 1 or 2. Only a small number of patients suffered from grade 4 leucopenia (4.5%) or thrombocytopenia (2.3%). The local relapse-free survival (LRFS), nodal relapse-free survival (NRFS), local-nodal relapse-free survival (LNRFS), distant metastasis-free survival (DMFS) and overall survival (OS) were 96.7%, 95.5%, 92.2%, 92.7% and 93.2%, at 2 years, respectively, with no significant difference compared with the P70 study. Conclusions Smart delivered via the helical tomotherapy technique appears to be associated with an acceptable acute toxicity profile and favorable short-term outcomes for patients with NPC. Long-term toxicities and patient outcomes are under investigation. PMID:27247555

  11. A clinical comparative study of Cadiax Compact II and intraoral records using wax and addition silicone.

    PubMed

    Torabi, Kianoosh; Pour, Sasan Rasaei; Ahangari, Ahmad Hassan; Ghodsi, Safoura

    2014-01-01

    Evaluation of mandibular movements is necessary to form the occlusal anatomical contour, analyze the temporomandibular joint status, and evaluate the patient's occlusion. This clinical study was conducted to compare the mandibular recording device Cadiax Compact II with routine intraoral records for measuring condylar inclinations. The results showed that the differences between Cadiax and intraoral records were statistically significant for all measurements. Cadiax measurements had a stronger correlation with silicone records. The quantities of recorded Bennett angles were lower and the values of sagittal condylar inclination were higher with Cadiax than with routine intraoral records. PMID:25390868

  12. Simultaneous determination of five common additives in insulating mineral oils by high-performance liquid chromatography with ultraviolet and coulometric detection.

    PubMed

    Bruzzoniti, Maria Concetta; Sarzanini, Corrado; Rivoira, Luca; Tumiatti, Vander; Maina, Riccardo

    2016-08-01

    Dielectric mineral oils are used to impregnate power transformers and large electrical apparatus, acting as both liquid insulation and heat dissipation media. Antioxidants and passivators are frequently added to mineral oils to enhance oxidation stability and reduce the electrostatic charging tendency, respectively. Since existing standard test methods only allow analysis of individual additives, new approaches are needed for the detection of mixtures. For the first time we investigate and discuss the performance of analytical methods, which require or do not require extraction as sample pretreatment, for the simultaneous reversed-phase high-performance liquid chromatography determination of passivators (benzotriazole, Irgamet(®) 39) and antioxidants (N-phenyl-1-naphtylamine, 2,6-di-tert-butylphenol, 2,6-di-tert-butyl-p-cresol), chosen for their presence in marketed oils. Quick easy, cheap, effective, rugged and safe and solid phase extractions were evaluated as sample pretreatments. Direct sample-injection was also studied. Ultraviolet spectrophotometry and direct-current coulometry detection were explored. As less prone to additive concentrations variability, the direct-injection high-performance liquid chromatography with ultraviolet and coulometric detection method was validated through comparison with Standard Method IEC 60666 and through an ASTM interlaboratory proficiency test. Obtained detection limits are (mg kg(-1) ): benzotriazole (2.8), Irgamet(®) 39 (13.8), N-phenyl-1-naphtylamine (11.9), 2,6-di-tert-butylphenol (13.1), 2,6-di-tert-butyl-p-cresol (10.2). Simultaneous determination of selected additives was possible both in unused and used oils, with good precision and accuracy. PMID:27279638

  13. Acquisition of Mn(II) in Addition to Fe(II) Is Required for Full Virulence of Salmonella enterica Serovar Typhimurium

    PubMed Central

    Boyer, E.; Bergevin, I.; Malo, D.; Gros, P.; Cellier, M. F. M.

    2002-01-01

    The roles of the genes feoB (ABC ferrous iron transporter), mntH (proton-dependent manganese transporter), and sitABCD (putative ABC iron and/or manganese transporter) in Salmonella pathogenicity were investigated by using mutant strains deficient in one, two, or three transporters. Our results indicated that sitABCD encodes an important transporter of Mn(II) and Fe(II) which is required for full virulence in susceptible animals (Nramp1−/−) and for replication inside Nramp1−/− macrophages in vitro. The mntH sitABCD double mutant (mutant MS) showed minimal Mn(II) uptake and increased sensitivity to H2O2 and to the divalent metal chelator 2,2′-dipyridyl (DP) and was defective for replication in macrophages. In vivo MS appeared to be as virulent as the sitABCD mutant in Nramp1−/− animals. The ferrous iron transporter Feo was required for full virulence in 129/Sv Nramp1−/− mice, and infection with multiple mutants lacking FeoB was not fatal. The sitABCD feoB mutant (mutant SF) and the mntH sitABCD feoB mutant (mutant MSF) showed minimal Fe(II) uptake and were slightly impaired for replication in susceptible macrophages. MSF showed reduced growth in minimal medium deficient in divalent cations. The role of the mntH gene, which is homologous to mammalian Nramp genes, was also investigated after overexpression in the double mutant MS. MntH preferred Mn(II) over Fe(II) and could suppress MS sensitivity to H2O2 and to DP, and it also improved the intracellular survival in Nramp1−/− macrophages. This study indicates that acquisition of Mn(II), in addition to Fe(II), is required for intracellular survival and replication of Salmonella enterica serovar Typhimurium in macrophages in vitro and for virulence in vivo. PMID:12379679

  14. Bioavailability of zinc oxide added to corn tortilla is similar to that of zinc sulfate and is not affected by simultaneous addition of iron

    PubMed Central

    Rosado, Jorge L.; Díaz, Margarita; Muñoz, Elsa; Westcott, Jamie L.; González, Karla E.; Krebs, Nancy F.; Caamaño, María C.; Hambidge, Michael

    2013-01-01

    Background Corn tortilla is the staple food of Mexico and its fortification with zinc, iron, and other micronutrients is intended to reduce micronutrient deficiencies. However, no studies have been performed to determine the relative amount of zinc absorbed from the fortified product and whether zinc absorption is affected by the simultaneous addition of iron. Objective To compare zinc absorption from corn tortilla fortified with zinc oxide versus zinc sulfate and to determine the effect of simultaneous addition of two doses of iron on zinc bioavailability. Methods A randomized, double-blind, crossover design was carried out in two phases. In the first phase, 10 adult women received corn tortillas with either 20 mg/kg of zinc oxide added, 20 mg/kg of zinc sulfate added, or no zinc added. In the second phase, 10 adult women received corn tortilla with 20 mg/kg of zinc oxide added and either with no iron added or with iron added at one of two different levels. Zinc absorption was measured by the stable isotope method. Results The mean (± SEM) fractional zinc absorption from unfortified tortilla, tortilla fortified with zinc oxide, and tortilla fortified with zinc sulfate did not differ among treatments: 0.35 ± 0.07, 0.36 ± 0.05, and 0.37 ± 0.07, respectively. The three treatment groups with 0, 30, and 60 mg/kg of added iron had similar fractional zinc absorption (0.32 ± 0.04, 0.33 ± 0.02, and 0.32 ± 0.05, respectively) and similar amounts of zinc absorbed (4.8 ± 0.7, 4.5 ± 0.3, and 4.8 ± 0.7 mg/day, respectively). Conclusions Since zinc oxide is more stable and less expensive and was absorbed equally as well as zinc sulfate, we suggest its use for corn tortilla fortification. Simultaneous addition of zinc and iron to corn tortilla does not modify zinc bioavailability at iron doses of 30 and 60 mg/kg of corn flour. PMID:23424892

  15. Kinetic spectrophotometric H-point standard addition method for the simultaneous determination of diloxanide furoate and metronidazole in binary mixtures and biological fluids

    NASA Astrophysics Data System (ADS)

    Issa, Mahmoud Mohamed; Nejem, R.'afat Mahmoud; Shanab, Alaa Mohamed Abu; Shaat, Nahed Talab

    2013-10-01

    Simple, reliable, and sensitive kinetic spectrophotometric method has been developed for the simultaneous determination of diloxanide furoate and metronidazole using H-point standard addition method (HPSAM). The method is based on the oxidation rate difference of diloxanide and metronidazole by potassium permanganate in basic medium. A green color has been developed and measured at 610 nm. Different experimental parameters were carefully optimized. The limiting logarithmic and the initial-rate methods were adopted for the construction of the calibration curve of each individual reaction with potassium permanganate. Under the optimum conditions, Beer's law was obeyed in the range of 1.0-20.0 and 5.0-25.0 μg ml-1 for diloxanide furoate and metronidazole, respectively. The detection limits were 0.22 μg ml-1 for diloxanide furoate and 0.83 μg ml-1 for metronidazole. Correlation coefficients of the regression equations were greater than 0.9970 in all cases. The precision of the method was satisfactory; the maximum value of relative standard deviation did not exceed 1.06% (n = 5). The accuracy, expressed as recovery was between 99.4% and 101.4% with relative error of 0.12 and 0.14 for diloxanide furoate and metronidazole, respectively. The proposed method was successfully applied for the simultaneous determination of both drugs in pharmaceutical dosage forms and human urine samples and compared with alternative HPLC method.

  16. HUMAN HEALTH DAMAGES FROM MOBILE SOURCE AIR POLLUTION: ADDITIONAL DELPHI DATA ANALYSIS. VOLUME II

    EPA Science Inventory

    The report contains the results of additional analyses of the data generated by a panel of medical experts for a study of Human Health Damages from Mobile Source Air Pollution (hereafter referred to as HHD) conducted by the California Air Resources Board in 1973-75 for the U.S. E...

  17. The Modern U.S. High School Astronomy Course, Its Status and Makeup II: Additional Results

    ERIC Educational Resources Information Center

    Krumenaker, Larry

    2009-01-01

    A postal survey of high school astronomy teachers strongly confirms many results of an earlier electronic survey. Additional and new results include a measure of the level of inquiry (more structured inquiry and teacher-led) in the classroom as well as data showing that more emphasis is given to traditional topics than to contemporary astronomy…

  18. A New Chelating Reagent: Its Synthesis/Characterization and Application for the Determination of Cd(II) and Ni(II) in Various Food and Make-Up Product Samples by FAAS Using Simultaneous Microextraction Sampling.

    PubMed

    Saçmacı, Şerife; Saçmacı, Mustafa

    2016-07-01

    A new and simple dispersive liquid-liquid simultaneous microextraction procedure was developed for the rapid separation and simultaneous extraction/preconcentration of Cd(II) and Ni(II) at ultratrace amounts. Microextraction of the analytes was carried out in the presence of 2-methyl-5-[(Z)-pyridin-4-yldiazenyl]quinolin-8-ol as the chelating reagent. Chloroform and ethanol were used as the extraction and dispersive solvents. Various parameters that influence the microextraction procedure's efficiency-such as pH, centrifugation rate and time, reagent concentration, and sampling volume on the recovery of analytes-were examined. The calibration curves were linear in the range of 0.01-1.25 and 0.075-5 mg/L with LODs of 0.25 and 0.84 μg/L, and with a preconcentration factor of 94, for Cd(II) and Ni(II), respectively. Precision was >1.0%. The accuracy of the method was confirmed by analyzing the Certified Standard Reference Material (CWW-TMD: Certified wastewater-Trace metals, wastewater). The results show that the dispersive liquid-liquid simultaneous microextraction pretreatment is a sensitive, rapid, simple, green, and safe method for the separation/preconcentration of cadmium and nickel. PMID:27301349

  19. Simultaneous Adsorption and Degradation of Cr(VI) and Cd(II) Ions from Aqueous Solution by Silica-Coated Fe0 Nanoparticles

    PubMed Central

    Ma, Hongpu; Ren, Bozhi; Li, Tielong

    2013-01-01

    Core-shell silica-coated Fe0 nanoparticles (Fe@SiO2) were prepared in one-step synthesis by aqueous reduction combined with modified Stöber method. The as-prepared Fe@SiO2 were then used for simultaneous removal of Cr(VI) and Cd(II) from aqueous solution. Batch tests indicated that Fe@SiO2 exhibited high removal capacity toward Cr(VI) and Cd(II). Cr(VI) was removed by Fe@SiO2 through reduction rather than adsorption, while Cd(II) removal was mainly through adsorption. The removal rate increased with increasing initial Fe NPs dose and decreased with increasing initial Cr(VI) and Cd(II) concentrations. Cd(II) adsorption was also strengthened by Cr(VI) reduction with the release of OH−. The removals of Cr(VI) and Cd(II) were weakened in the presence of cations or humic acid, as a result of aggregation and less active site of Fe@SiO2. Overall, the simply prepared Fe@SiO2 were potential material for the heavy metals removed from water. PMID:24455425

  20. Effect of complete extraction and re-addition of manganese on thermoluminescence of pea Photosystem II preparations.

    PubMed

    Klimov, V V; Allakhverdiev, S I; Shafiev, M A; Demeter, S

    1985-10-01

    Thermoluminescence of Photosystem II particles isolated from pea chloroplasts using digitonin and Triton X-100 was measured after 1 min illumination at a certain temperature (T(ex)) followed by illumination during cooling (40 Cdeg/min) to a lower temperature. Glow curves of the particles are characteristic of the photosynthetic oxygen-evolving material studied earlier. Complete (more than 95%) removal of Mn from the Photosystem II particles abolishes thermoluminescence bands around 0° C, related to the oxygen-evolving system, but the thermoluminescence bands peaking around -30°C (TL(-30)), -55°C (TL_ (-55)) and between-68 and -85° C, depending on Tex(TLv), remain unaltered. The bands are characterized by different dependence on T,x. The TL(-30), TL(-55) and TL v bands can also be observed in the glow curve of isolated pea and spinach chloroplasts. Re-addition of MnCI (2) (2 μM, corresponding to nearly 4 Mn atoms per reaction center of Photosystem II) to the Mn-depleted particles does not reactivate the thermoluminescence bands around 0° C. However, it does lead to suppression of TL(-30) accompanied by parallel activation of TL(-55), revealing competition of the TL (-30) and TL(-55) for charges generated by the reaction center. These data, as well as the results on the effect of inhibitors and electron donors to Photosystem II, show that positive charges contributing to the TL(-30), TL (-55) and TL v thermoluminescence bands are located on secondary electron donors of Photosystem II which do not require Mn and are located closer to the reaction center than the Mn-containing, water-oxidizing enzyme. PMID:22860268

  1. Simultaneous removal of methylene blue and copper(II) ions by photoelectron catalytic oxidation using stannic oxide modified iron(III) oxide composite electrodes.

    PubMed

    Qi, Jinqiu; Li, Xiaochen; Zheng, Hao; Li, Peiqiang; Wang, Huying

    2015-08-15

    Stannic oxide modified Fe(III) oxide composite electrodes (SnO2/Fe2O3) were synthesized for simultaneously removing methylene blue (MB) and Cu(II) from wastewater using photoelectron catalytic oxidation (PEO). The SnO2/Fe2O3 electrodes were characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD), and photoelectrochemical techniques. The removal of MB and Cu(II) by PEO using the SnO2/Fe2O3 composite electrodes was studied in terms of reaction time, electric current density, and pH of the electrolyte. The kinetics of the reactions were investigated using batch assays. The optimal reaction time, pH, and electric current density of the PEO process were determined to be 30 min, 6.0, and 10 mA/cm(2), respectively. The removal rates of MB from wastewater treated by PEO and electron catalytic oxidation process were 84.87% and 70.64%, respectively, while the recovery rates of Cu(II) were 91.75% and 96.78%, respectively. The results suggest that PEO is an effective method for the simultaneous removal of MB and Cu(II) from wastewater, and the PEO process exhibits a much higher removal rate for MB and Cu(II) compared to the electron catalytic oxidation process. Furthermore, the removal of MB was found to follow the Langmuir-Freundlich-Hinshelwood kinetic model, whereas the removal of Cu(II) fitted well to the first-order reaction model. PMID:25855567

  2. Simultaneous determination of some food additives in soft drinks and other liquid foods by flow injection on-line dialysis coupled to high performance liquid chromatography.

    PubMed

    Kritsunankul, Orawan; Jakmunee, Jaroon

    2011-06-15

    Flow injection on-line dialysis was developed for sample pretreatment prior to the simultaneous determination of some food additives by high performance liquid chromatography (FID-HPLC). A liquid sample or mixed standard solution (900 μL) was injected into a donor stream (5%, w/v, sucrose) of FID system and was pushed further through a dialysis cell, while an acceptor solution (0.025 mol L(-1) phosphate buffer, pH 3.75) was held in the opposite side of the dialysis membrane. The dialysate was then flowed to an injection loop of the HPLC valve, where it was further injected into the HPLC system and analyzed under isocratic reverse-phase HPLC conditions and UV detection (230 nm). The order of elution of five food additives was acesulfame-K, saccharin, caffeine, benzoic acid and sorbic acid, respectively, with the analysis time of 14 min. On-line dialysis and HPLC analysis could be performed in parallel, providing sample throughput of 4.3h(-1). Dialysis efficiencies of five food additives were in ranges of 5-11%. Linear calibration graphs were in ranges of 10-100 mg L(-1) for acesulfame-K and saccharin, 10-250 mg L(-1) for benzoic acid and 10-500 mg L(-1) for caffeine and sorbic acid. Good precisions (RSD<5%) for all the additives were obtained. The proposed system was applied to soft drink and other liquid food samples. Acceptable percentage recoveries could be obtained by appropriate dilution of the sample before injecting into the system. The developed system has advantages of high degrees of automation for sample pretreatment, i.e., on-line sample separation and dilution and low consumption of chemicals and materials. PMID:21641449

  3. Impact of high microwave power on hydrogen impurity trapping in nanocrystalline diamond films grown with simultaneous nitrogen and oxygen addition into methane/hydrogen plasma

    NASA Astrophysics Data System (ADS)

    Tang, C. J.; Fernandes, A. J. S.; Jiang, X. F.; Pinto, J. L.; Ye, H.

    2016-01-01

    In this work, we study for the first time the influence of microwave power higher than 2.0 kW on bonded hydrogen impurity incorporation (form and content) in nanocrystalline diamond (NCD) films grown in a 5 kW MPCVD reactor. The NCD samples of different thickness ranging from 25 to 205 μm were obtained through a small amount of simultaneous nitrogen and oxygen addition into conventional about 4% methane in hydrogen reactants by keeping the other operating parameters in the same range as that typically used for the growth of large-grained polycrystalline diamond films. Specific hydrogen point defect in the NCD films is analyzed by using Fourier-transform infrared (FTIR) spectroscopy. When the other operating parameters are kept constant (mainly the input gases), with increasing of microwave power from 2.0 to 3.2 kW (the pressure was increased slightly in order to stabilize the plasma ball of the same size), which simultaneously resulting in the rise of substrate temperature more than 100 °C, the growth rate of the NCD films increases one order of magnitude from 0.3 to 3.0 μm/h, while the content of hydrogen impurity trapped in the NCD films during the growth process decreases with power. It has also been found that a new H related infrared absorption peak appears at 2834 cm-1 in the NCD films grown with a small amount of nitrogen and oxygen addition at power higher than 2.0 kW and increases with power higher than 3.0 kW. According to these new experimental results, the role of high microwave power on diamond growth and hydrogen impurity incorporation is discussed based on the standard growth mechanism of CVD diamonds using CH4/H2 gas mixtures. Our current experimental findings shed light into the incorporation mechanism of hydrogen impurity in NCD films grown with a small amount of nitrogen and oxygen addition into methane/hydrogen plasma.

  4. Assessment of Nano Cellulose from Peach Palm Residue as Potential Food Additive: Part II: Preliminary Studies.

    PubMed

    Andrade, Dayanne Regina Mendes; Mendonça, Márcia Helena; Helm, Cristiane Vieira; Magalhães, Washington L E; de Muniz, Graciela Ines Bonzon; Kestur, Satyanarayana G

    2015-09-01

    High consumption of dietary fibers in the diet is related to the reduction of the risk of non-transmitting of chronic diseases, prevention of the constipation etc. Rich diets in dietary fibers promote beneficial effects for the metabolism. Considering the above and recognizing the multifaceted advantages of nano materials, there have been many attempts in recent times to use the nano materials in the food sector including as food additive. However, whenever new product for human and animal consumption is developed, it has to be tested for their effectiveness regarding improvement in the health of consumers, safety aspects and side effects. However, before it is tried with human beings, normally such materials would be assessed through biological tests on a living organism to understand its effect on health condition of the consumer. Accordingly, based on the authors' finding reported in a previous paper, this paper presents body weight, biochemical (glucose, cholesterol and lipid profile in blood, analysis of feces) and histological tests carried out with biomass based cellulose nano fibrils prepared by the authors for its possible use as food additive. Preliminary results of the study with mice have clearly brought out potential of these fibers for the said purpose. PMID:26344977

  5. A novel ion-pairing chromatographic method for the simultaneous determination of both nicarbazin components in feed additives: chemometric tools for improving the optimization and validation.

    PubMed

    De Zan, María M; Teglia, Carla M; Robles, Juan C; Goicoechea, Héctor C

    2011-07-15

    The development, optimization and validation of an ion-pairing high performance liquid chromatography method for the simultaneous determination of both nicarbazin (NIC) components: 4,4'-dinitrocarbanilide (DNC) and 2-hydroxy-4,6-dimethylpyrimidine (HDP) in bulk materials and feed additives are described. An experimental design was used for the optimization of the chromatographic system. Four variables, including mobile phase composition and oven temperature, were analyzed through a central composite design exploring their contribution to analyte separation. Five responses: peak resolutions, HDP capacity factor, HDP tailing and analysis time, were modelled by using the response surface methodology and were optimized simultaneously by implementing the desirability function. The optimum conditions resulted in a mobile phase consisting of 10.0 mmol L(-1) of 1-heptanesulfonate, 20.0 mmol L(-1) of sodium acetate, pH=3.30 buffer and acetonitrile in a gradient system at a flow rate of 1.00 mL min(-1). Column was an INERSTIL ODS-3 (4.6 mm×150 mm, 5 μm particle size) at 40.0°C. Detection was performed at 300 nm by a diode array detector. The validation results of the method indicated a high selectivity and good precision characteristics, with RSD less than 1.0% for both components, both in intra and inter-assay precision studies. Linearity was proved for a range of 32.0-50.0 μg mL(-1) of NIC in sample solution. The recovery, studied at three different fortification levels, varied from 98.0 to 101.4 for HDP and from 99.1 to 100.2 for DNC. The applicability of the method was demonstrated by determining DNC and HDP content in raw materials and commercial formulations used for coccidiosis prevention. Assays results on real samples showed that considerable differences in molecular ratio DNC:HDP exist among them. PMID:21645683

  6. [THE TECHNIQUE OF HIGH-PERFORMANCE LIQUID CHROMATOGRAPHY FOR SIMULTANEOUS DIAGNOSTIC OF INHERENT HYPERPLASIA OF ADRENAL GLANDS TYPE I AND II].

    PubMed

    Dutov, A A; Nikitin, D A; Lukyanova, Yu L; Shemiakina, N A

    2016-01-01

    The article considers the technique of high-performance liquid chromatography making it possible simultaneously detect cortisol, cortisone and secondary steroids in serum for consequent analysis of common reversed-phase high-performance liquid chromatography with ultraviolet under 240 nm. The liquid-liquid extraction from alkaline medium in diethyl ether The separation using column of 150x4.6 size ODS 3.5 mkm in isocratic mode. The eluent acetonitrile--0.02 M phosphate buffer pH 8.0--isopropanol (40:60:1). The application of proposed technique managed to separate cortisol, cortisone, dexamethasone, corticosterone, 11-desoxicortisol, testosterone, desoxicorticosterone, 17α-gidroxiprogesterone and androstendion in 20 minutes. The simplicity, reproducibility and sufficient selectivity and sensitivity of technique permit implement it in clinical practice for simultaneous diagnostic of inherent hyperplasia of adrenal glands type I and II. PMID:27183726

  7. Multiresidue method for the simultaneous determination of veterinary medicinal products, feed additives and illegal dyes in eggs using liquid chromatography-tandem mass spectrometry.

    PubMed

    Piatkowska, Marta; Jedziniak, Piotr; Zmudzki, Jan

    2016-04-15

    A multiclass method was developed for the simultaneous determination of 120 analytes in fresh eggs. The method covers the analytes from the groups of tetracyclines (6), fluoroquinolones (11), sulphonamides (17), nitroimidazoles (9), amphenicols (2), cephalosporins (7), penicillins (8), macrolides (8), benzimidazoles (20), coccidiostats (14), insecticides (3), dyes (12) and others (3). Samples were extracted using 0.1% formic acid in acetonitrile:water (8:2) with the addition of EDTA and cleaned using solid phase extraction with Hybrid SPE cartridges. The chromatographic separation was achieved on C8 column using mobile phase consisting of (A) methanol:acetonitrile (8:2) - (B) 0.1% formic acid in a gradient mode. Validation results according to the Commission Decision 2002/657/EC are as follows: linearity (r⩾0.99), recovery (75-108%), repeatability (CV 1.60-15.9%), reproducibility (CV 2.60-15%), decision limit (CCα 2.25-1156 μg/kg) and detection capability (CCβ 2.04-1316 μg/kg). The presented method was used for analysis of 150 real eggs samples taken from monitoring control program. PMID:26616990

  8. Flow-injection simultaneous determination of iron(III) and copper(II) and of iron(III) and palladium(II) based on photochemical reactions of thiocyanato-complexes.

    PubMed

    Oguma, Koichi; Yoshioka, Osamu

    2002-12-01

    The flow injection analysis systems have been developed for the simultaneous determination of iron(III) and copper(II) and of iron(III) and palladium(II) based on the photochemical reactions of their thiocyanato-complexes. In the first system, a sample solution was injected in to nitric acid solution and mixed with ammonium thiocyanate solution, followed by spectrophotometric monitoring of the thiocyanato-complexes formed. Another aliquot of the same sample solution was injected and the thiocyanato-complexes formed in the same way were irradiated by UV light before spectrophotometric monitoring. In another system, the absorbance of thiocyanato-complexes formed by each sample injection was monitored with two flow cells aligned with the same optical path before and after UV irradiation. The difference in the extent of photochemical decomposition of the thiocyanato-complexes enabled simultaneous determinations of iron(III) and copper(II) and of iron(III) and palladium(II) at levels of several mugml(-1) to some tens mugml(-1) in their admixtures. Sample throughputs are 40 and 20 h(-1) by the former and latter systems, respectively. PMID:18968842

  9. Heterogeneous versus homogeneous copper(II) catalysis in enantioselective conjugate-addition reactions of boron in water.

    PubMed

    Kitanosono, Taku; Xu, Pengyu; Kobayashi, Shū

    2014-01-01

    We have developed Cu(II)-catalyzed enantioselective conjugate-addition reactions of boron to α,β-unsaturated carbonyl compounds and α,β,γ,δ-unsaturated carbonyl compounds in water. In contrast to the previously reported Cu(I) catalysis that required organic solvents, chiral Cu(II) catalysis was found to proceed efficiently in water. Three catalyst systems have been exploited: cat. 1: Cu(OH)2 with chiral ligand L1; cat. 2: Cu(OH)2 and acetic acid with ligand L1; and cat. 3: Cu(OAc)2 with ligand L1. Whereas cat. 1 is a heterogeneous system, cat. 2 and cat. 3 are homogeneous systems. We tested 27 α,β-unsaturated carbonyl compounds and an α,β-unsaturated nitrile compound, including acyclic and cyclic α,β-unsaturated ketones, acyclic and cyclic β,β-disubstituted enones, acyclic and cyclic α,β-unsaturated esters (including their β,β-disubstituted forms), and acyclic α,β-unsaturated amides (including their β,β-disubstituted forms). We found that cat. 2 and cat. 3 showed high yields and enantioselectivities for almost all substrates. Notably, no catalysts that can tolerate all of these substrates with high yields and high enantioselectivities have been reported for the conjugate addition of boron. Heterogeneous cat. 1 also gave high yields and enantioselectivities with some substrates and also gave the highest TOF (43,200 h(-1) ) for an asymmetric conjugate-addition reaction of boron. In addition, the catalyst systems were also applicable to the conjugate addition of boron to α,β,γ,δ-unsaturated carbonyl compounds, although such reactions have previously been very limited in the literature, even in organic solvents. 1,4-Addition products were obtained in high yields and enantioselectivities in the reactions of acyclic α,β,γ,δ-unsaturated carbonyl compounds with diboron 2 by using cat. 1, cat. 2, or cat. 3. On the other hand, in the reactions of cyclic α,β,γ,δ-unsaturated carbonyl compounds with compound 2, whereas 1,4-addition products

  10. BUTANOL PRODUCTION FROM WHEAT STRAW BY SIMULTANEOUS SACCHARIFICATION AND FERMENTATION USING CLOSTRIDIUM BEIJERINCKII: PART II - FED-BATCH FERMENTATION

    Technology Transfer Automated Retrieval System (TEKTRAN)

    In these studies, Clostridium beijerinckii P260 was used to produce butanol (acetone butanol ethanol, or ABE) from wheat straw (WS) hydrolyzate in a fed-batch reactor. It has been demonstrated that simultaneous hydrolysis of WS to achieve 100% hydrolysis to simple sugars (to the extent achievable u...

  11. Lipoamide Acts as an Indirect Antioxidant by Simultaneously Stimulating Mitochondrial Biogenesis and Phase II Antioxidant Enzyme Systems in ARPE-19 Cells.

    PubMed

    Zhao, Lin; Liu, Zhongbo; Jia, Haiqun; Feng, Zhihui; Liu, Jiankang; Li, Xuesen

    2015-01-01

    In our previous study, we found that pretreatment with lipoamide (LM) more effectively than alpha-lipoic acid (LA) protected retinal pigment epithelial (RPE) cells from the acrolein-induced damage. However, the reasons and mechanisms for the greater effect of LM than LA are unclear. We hypothesize that LM, rather than the more direct antioxidant LA, may act more as an indirect antioxidant. In the present study, we treated ARPE-19 cells with LA and LM and compared their effects on activation of mitochondrial biogenesis and induction of phase II enzyme systems. It is found that LM is more effective than LA on increasing mitochondrial biogenesis and inducing the expression of nuclear factor erythroid 2-related factor 2 (Nrf2) and its translocation to the nucleus, leading to an increase in expression or activity of phase II antioxidant enzymes (NQO-1, GST, GCL, catalase and Cu/Zn SOD). Further study demonstrated that mitochondrial biogenesis and phase II enzyme induction are closely coupled via energy requirements. These results suggest that LM, compared with the direct antioxidant LA, plays its protective effect on oxidative damage more as an indirect antioxidant to simultaneously stimulate mitochondrial biogenesis and induction of phase II antioxidant enzymes. PMID:26030919

  12. Lipoamide Acts as an Indirect Antioxidant by Simultaneously Stimulating Mitochondrial Biogenesis and Phase II Antioxidant Enzyme Systems in ARPE-19 Cells

    PubMed Central

    Zhao, Lin; Liu, Zhongbo; Jia, Haiqun; Feng, Zhihui; Liu, Jiankang; Li, Xuesen

    2015-01-01

    In our previous study, we found that pretreatment with lipoamide (LM) more effectively than alpha-lipoic acid (LA) protected retinal pigment epithelial (RPE) cells from the acrolein-induced damage. However, the reasons and mechanisms for the greater effect of LM than LA are unclear. We hypothesize that LM, rather than the more direct antioxidant LA, may act more as an indirect antioxidant. In the present study, we treated ARPE-19 cells with LA and LM and compared their effects on activation of mitochondrial biogenesis and induction of phase II enzyme systems. It is found that LM is more effective than LA on increasing mitochondrial biogenesis and inducing the expression of nuclear factor erythroid 2-related factor 2 (Nrf2) and its translocation to the nucleus, leading to an increase in expression or activity of phase II antioxidant enzymes (NQO-1, GST, GCL, catalase and Cu/Zn SOD). Further study demonstrated that mitochondrial biogenesis and phase II enzyme induction are closely coupled via energy requirements. These results suggest that LM, compared with the direct antioxidant LA, plays its protective effect on oxidative damage more as an indirect antioxidant to simultaneously stimulate mitochondrial biogenesis and induction of phase II antioxidant enzymes. PMID:26030919

  13. A double addition of Ln-H to a carbon-carbon triple bond and competitive oxidation of ytterbium(II) and hydrido centers.

    PubMed

    Basalov, Ivan V; Lyubov, Dmitry M; Fukin, Georgy K; Shavyrin, Andrei S; Trifonov, Alexander A

    2012-04-01

    Addition of two Ln-H bonds of an Yb(II) hydrido complex supported by bulky amidinate ligand to a C≡C bond lead to the formation of 1,2-dianionic bibenzyl fragment. Both Yb(II) and hydrido centers are oxidized under the reaction conditions. The resulting Yb(II)-η(6) -arene interaction is surprisingly robust: the arene cannot be replaced from the metal coordination sphere when treated with Lewis bases. PMID:22374856

  14. Concise Enantioselective Synthesis of Oxygenated Steroids via Sequential Copper(II)-Catalyzed Michael Addition/Intramolecular Aldol Cyclization Reactions

    PubMed Central

    Cichowicz, Nathan R.; Kaplan, Will; Khomutnyk, Yaroslav; Bhattarai, Bijay; Sun, Zhankui; Nagorny, Pavel

    2015-01-01

    A new scalable enantioselective approach to functionalized oxygenated steroids is described. This strategy is based on chiral bis(oxazoline) copper(II) complex-catalyzed enantioselective and diastereoselective Michael reactions of cyclic ketoesters and enones to install vicinal quaternary and tertiary stereocenters. In addition, the utility of copper(II) salts as highly active catalysts for the Michael reactions of traditionally unreactive ββ′-enones and substituted ββ′-ketoesters that results in unprecedented Michael adducts containing vicinal all-carbon quaternary centers is also demonstrated. The Michael adducts subsequently undergo base-promoted diastereoselective aldol cascade reactions resulting in the natural or unnatural steroid skeletons. The experimental and computational studies suggest that the torsional strain effects arising from the presence of the Δ5-unsaturation are key controling elements for the formation of the natural cardenolide scaffold. The described method enables expedient generation of polycyclic molecules including modified steroidal scaffolds as well as challenging-to-synthesize Hajos-Parrish and Wieland-Miescher ketones. PMID:26491886

  15. An Insoluble Copper(II) Acetylacetonate-Chiral Bipyridine Complex that Catalyzes Asymmetric Silyl Conjugate Addition in Water.

    PubMed

    Kitanosono, Taku; Zhu, Lei; Liu, Chang; Xu, Pengyu; Kobayashi, Shū

    2015-12-16

    Acicular purplish crystals were obtained from Cu(acac)2 and a chiral bipyridine ligand. Although the crystals were not soluble, they nevertheless catalyzed asymmetric silyl conjugate addition of lipophilic substrates in water. Indeed, the reactions proceeded efficiently only in water; they did not proceed well either in organic solvents or in mixed water/organic solvents in which the catalyst/substrates were soluble. This is in pronounced contrast to conventional organic reactions wherein the catalyst/substrates tend to be in solution. Several advantages of the chiral Cu(II) catalysis in water over previously reported catalyst systems have been demonstrated. Water is expected to play a prominent role in constructing and stabilizing sterically confined transition states and accelerating subsequent protonation to achieve high yields and enantioselectivities. PMID:26646601

  16. Pairwise additivity of energy components in protein-ligand binding: the HIV II protease-Indinavir case.

    PubMed

    Ucisik, Melek N; Dashti, Danial S; Faver, John C; Merz, Kenneth M

    2011-08-28

    An energy expansion (binding energy decomposition into n-body interaction terms for n ≥ 2) to express the receptor-ligand binding energy for the fragmented HIV II protease-Indinavir system is described to address the role of cooperativity in ligand binding. The outcome of this energy expansion is compared to the total receptor-ligand binding energy at the Hartree-Fock, density functional theory, and semiempirical levels of theory. We find that the sum of the pairwise interaction energies approximates the total binding energy to ∼82% for HF and to >95% for both the M06-L density functional and PM6-DH2 semiempirical method. The contribution of the three-body interactions amounts to 18.7%, 3.8%, and 1.4% for HF, M06-L, and PM6-DH2, respectively. We find that the expansion can be safely truncated after n=3. That is, the contribution of the interactions involving more than three parties to the total binding energy of Indinavir to the HIV II protease receptor is negligible. Overall, we find that the two-body terms represent a good approximation to the total binding energy of the system, which points to pairwise additivity in the present case. This basic principle of pairwise additivity is utilized in fragment-based drug design approaches and our results support its continued use. The present results can also aid in the validation of non-bonded terms contained within common force fields and in the correction of systematic errors in physics-based score functions. PMID:21895219

  17. Ion exchange equilibria in simultaneous extraction of platinum(II, IV) and rhodium(III) from hydrochloric solutions

    NASA Astrophysics Data System (ADS)

    Mel'nikov, A. M.; Kononova, O. N.; Pavlenko, N. I.; Krylov, A. S.

    2012-06-01

    Regularities of sorption extraction of platinum(II, IV) and rhodium(III) by anion exchangers of various physical and chemical structure in the presence of hydrochloric media were studied. It is established that AM-2B, Purolite A 500, and Purolite S 985 ionites adsorb complex anions of platinum metals employing mixed mechanism. A high affinity of the studied anionites for the studied complex anions of platinum and rhodium is established.

  18. Novel process for simultaneous removal of NO(x) and SO2 from simulated flue gas by using a sustainable Ag(I)/Ag(II) redox mediator.

    PubMed

    Raju, Thasan; Chung, Sang Joon; Moon, Il Shik

    2008-10-01

    The objective of this work is to develop a sustainable process for simultaneous removal of waste gases such as NO, NO2, and SO2 by an electrochemically generated Ag(I)/Ag(II) redox mediator system. High removal efficiency was achieved for NO and SO2 by the wet scrubbing method at room temperature and atmospheric pressure. This removal is achieved through oxidation and absorption by contacting the gaseous stream with redox mediator ions that offer specific or selective solubility for the solute gases to be recovered in a wet scrubber. The process parameters such as gas velocity, liquid velocity, Ag(I) concentration, and HNO3 concentration were investigated to explore the possibility of complete removal of waste gases. The Ag(I)/Ag(II)-based mediated electrochemical oxidation process proved to be quite effective for simultaneous removal of NO, NO(x), and SO2 from the simulated flue gas mixtures containing NO and SO2 over a wide concentration range of 100-400 ppm. Studies were carried out with individual gas components for the mixture, and the effect of input NO and input SO2 concentrations on the NO(x) and SO2 removal efficiencies at 20 degrees C was examined. Complete oxidation of NO to NO2 with 100% NO removal efficiency and 92% NO(x) removal efficiency was achieved along with 100% SO2 removal efficiency, highlighting a potentially far greater efficiency of the Ag(I)/Ag(II)-based system in functionality and selectivity. Active research work in this direction is anticipated in the near future. PMID:18939587

  19. Simultaneous determination and pharmacokinetic study of Atractylenolide I, II and III in rat plasma after intragastric administration of Baizhufuling extract and Atractylodis extract by UPLC-MS/MS.

    PubMed

    Yan, Han; Sun, Yuanyuan; Zhang, Qili; Yang, Mingjing; Wang, Xiaorui; Wang, Yang; Yu, Zhiguo; Zhao, Yunli

    2015-07-01

    A simple and rapid ultra high performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) method was developed for the simultaneous determination of Atractylenolide I, II and III in rat plasma. Plasma samples were processed by liquid-liquid extraction with ethyl acetate, using schisandrin as internal standard (IS). Chromatographic separation was accomplished on a Thermo Hypersil GOLD C18 column (2.1mm×50mm, 1.9μm) with mobile phase consisting of acetonitrile and 0.1% formic acid-water (50:50, v/v). The detection was carried out by ESI-MS (positive ionization mode) and low-energy collision dissociation tandem mass spectrometric analyses using the multiple-reaction monitoring (MRM) scan mode. The quantification was performed using the transitions of the protonated molecule→product ion at m/z 231.0→185.1 for Atractylenolide I, at m/z 233.1→187.1 for Atractylenolide II and at m/z 249.1→231.1 for Atractylenolide III, respectively. Method validation revealed excellent linearity over investigated range together with satisfactory intra- and inter-day precision, accuracy, matrix effects and extraction recoveries. This method was successfully applied to the comparative pharmacokinetic study of Atractylenolide I, II and III in rat plasma after intragastric administration of Baizhufuling extract and Atractylodis extract. PMID:26001909

  20. Investigation of simultaneous biosorption of copper(II) and chromium(VI) on dried Chlorella vulgaris from binary metal mixtures: Application of multicomponent adsorption isotherms

    SciTech Connect

    Aksu, Z.; Acikel, U.; Kutsal, T.

    1999-02-01

    Although the biosorption of single metal ions to various kinds of microorganisms has been extensively studied and the adsorption isotherms have been developed for only the single metal ion situation, very little attention has been given to the bioremoval and expression of adsorption isotherms of multimetal ions systems. In this study the simultaneous biosorption of copper(II) and chromium(VI) to Chlorella vulgaris from a binary metal mixture was studied and compared with the single metal ion situation in a batch stirred system. The effects of pH and single- and dual-metal ion concentrations on the equilibrium uptakes were investigated. In previous studies the optimum biosorption pH had been determined as 4.0 for copper(II) and as 2.0 for chromium(VI). Multimetal ion biosorption studies were performed at these two pH values. It was observed that the equilibrium uptakes of copper(II) or chromium(VI) ions were changed due to the biosorption pH and the presence of other metal ions. Adsorption isotherms were developed for both single- and dual-metal ions systems at these two pH values, and expressed by the mono- and multicomponent Langmuir and Freundlich adsorption models. Model parameters were estimated by nonlinear regression. It was seen that the adsorption equilibrium data fitted very well to the competitive Freundlich model in the concentration ranges studied.

  1. Fourier transform spectrometer observations of solar carbon monoxide. II - Simultaneous cospatial measurements of the fundamental and first-overtone bands, and Ca II K, in quiet and active regions

    NASA Technical Reports Server (NTRS)

    Ayres, T. R.; Testerman, L.; Brault, J. W.

    1986-01-01

    Fourier transform spectrometry has yielded simultaneous cospatial measurements of important diagnostics of thermal structure in the high solar photosphere and low chromosphere. It is noted that the anomalous behavior of the fundamental bands of CO in quiet areas near the limb is accentuated in an active region plage observed close to the limb. The difference between the core temperatures of the CO fundamental bands in a plage and a nearby quiet region at the limb is larger than the corresponding brightness temperature differences in the inner wings of the Ca II line measured in a quiet region and several plages closer to the disk center. Numerical simulations indicate that the disparate behavior of the CO bands with respect to Ca II K cannot be reconciled with existing single component thermal structure models; a two-component atmosphere is required.

  2. Simultaneous active intracellular delivery of doxorubicin and C6-ceramide shifts the additive/antagonistic drug interaction of non-encapsulated combination.

    PubMed

    Fonseca, Nuno A; Gomes-da-Silva, Lígia C; Moura, Vera; Simões, Sérgio; Moreira, João Nuno

    2014-12-28

    Drug resistance remains the Achilles tendon undermining the success of chemotherapy. It has been recognized that success requires the identification of compounds that, when combined, lead to synergistic tumor inhibition while simultaneously minimizing systemic toxicity. However, in vivo application of such protocols is dependent on the ability to deliver the appropriate drug ratio at the tumor level. In this respect, nanotechnology-based delivery platforms, like liposomes, offer an elegant solution for the in vivo translation of such strategy. In this work, we propose the active intracellular delivery of combinations of doxorubicin and the pro-apoptotic sphingolipid, C6-ceramide, using our previously described cytosolic triggered release-enabling liposomes, targeting nucleolin with the F3 peptide. Combination of doxorubicin (DXR):C6-ceramide (C6-Cer) at 1:2 molar ratio interacted synergistically against drug resistant/triple negative MDA-MB-231 breast cancer cells, as well as drug sensitive MDA-MB-435S melanoma cells. Cell viability studies indicated that F3-targeted liposomes encapsulating DXR:C6-Cer 1:2 molar ratio (p[F3]DC12) performed similarly as targeted liposomal DXR (p[F3]SL), encapsulating twice the amount of DXR, at the IC50, for an incubation time of 24 h. Importantly, F3-targeted liposomes encapsulating DXR:C6-Cer 1:2 molar ratio (p[F3]DC12) enabled a cell death above 90% at 24 h of treatment against both DXR-resistant and sensitive cells, unattainable by the F3-targeted liposomal doxorubicin. Furthermore, a F3-targeted formulation encapsulating a mildly additive/antagonistic DXR:C6-Cer 1:1 molar ratio (p[F3]DC11) enabled an effect above 90% for an incubation period as short as 4 h, suggesting that the delivery route at the cell level may shift the nature of drug interaction. Such activity, including the one for p[F3]DC12, induced a marked cell and nucleus swelling at similar extent, consistent with necrotic cell death. Overall, these results

  3. Research Papers Sponsored by the Commission on Private Philanthropy and Public Needs. Volume II: Philanthropic Fields of Interest, Part II-Additional Perspectives.

    ERIC Educational Resources Information Center

    Department of the Treasury, Washington, DC.

    Twelve papers discuss future changes and trends in philanthropic giving and activities. The report is Volume II, Part II of a five volume series examining the relationship between nonprofit institutions and their donors. The opening paper reviews the needs for better definition of the government's role in contracting and grant making, and for…

  4. Type 1 Diabetes in the Spanish Population: additional factors to Class II HLA-DR3 and -DR4

    PubMed Central

    Urcelay, Elena; Santiago, José L; de la Calle, Hermenegildo; Martínez, Alfonso; Méndez, Julián; Ibarra, José M; Maluenda, Carlos; Fernández-Arquero, Miguel; de la Concha, Emilio G

    2005-01-01

    Background The Major Histocompatibility Complex is the main genetic contributor to susceptibility to type 1 diabetes (T1D); genome-wide scans have consistently mapped increased predisposition to this region. The highest disease risk has been associated with HLA-DR3 and HLA-DR4. In particular, the DR3-positive ancestral haplotype 18.2 was reported as highly diabetogenic. We aimed to corroborate whether this haplotype increases the susceptibility conferred by the DQ2-DR3 alleles in a Mediterranean population. We also searched for additional susceptibility factors to the classic DQ2-DR3 and DQ8-DR4. Results Genetic MHC markers were analysed in a case-control study with 302 T1D patients and 529 ethnically matched controls. DR3-TNFa1b5 carrier rate was significantly higher in DR3-positive heterozygous T1D patients than in DR3-positive heterozygous controls (p = 0.0019; odds ratio OR [95% confidence interval CI] = 2.26 [1.3–3.93]). This data was confirmed analysing the allelic frequency, which includes the information corresponding to the DR3-homozygous individuals (p = 0.001; OR = 2.09) and by using the Arlequin software to check the DR3-positive haplotypes (p = 0.004;OR = 1.93). The present results provide strong evidence of a second susceptibility region in the ancestral haplotype 18.2 in the Spanish population. Moreover, we searched for T1D susceptibility factors in addition to the MHC classical ones, within the DR2-DQ6/DR3-DQ2/DR4-DQ8 negative population. Several genetic markers in both MHC class II (DQA1*0101-DQB1*0501 [p = 0.007;OR = 2.81], DQA1*0201-DQB1*0202 [p = 0.03; OR = 2.35]) and III (TNFa2b1 [p = 0.01 OR = 2.74], BAT-2*2 [p = 0.004; OR = 3.19]) were found. These different alleles associated with T1D were not independent and we observed linkage disequilibrium among them leading us to describe two new risk haplotypes (DQA1*0101-DQB1*0501-TNFa2b1 and DQA1*0201-DQB1*0202- BAT-2*2). Finally, we studied a T1D susceptibility/protection marker located in

  5. Simultaneous detection of a large flare in the X-ray and optical regions on the RS CVn-type star II Peg

    NASA Astrophysics Data System (ADS)

    Doyle, J. G.; Kellett, B. J.; Byrne, P. B.; Avgoloupis, S.; Mavridis, L. N.; Seiradakis, J. H.; Bromage, G. E.; Tsuru, T.; Makishima, K.; Makishima, K.; McHardy, I. M.

    1991-02-01

    Results are presented for a large flare detected simultaneously on the RS CVn star II Peg by the X-ray satellite GINGA and from ground-based Johnson U-band measurements. The total U-band flare energy is estimated to be at least 6.6 x 10 to the 34th erg. This compares with at least 4.6 x 10 to 34th erg in the 1-10 keV energy range. These values are lower limits to the true radiative output, since the U-band data relates only to the rise phase of the flare, while the X-ray data were obtained during part of the decay phase. Using a 'smooth-burst model', the combined U-band plus X-ray radiative output is estimated to be about 3 x 10 to the 34th erg.

  6. Simultaneous separation and determination of trace amounts of Cd(II) and Cu(II) in environmental samples using novel diphenylcarbazide modified nanoporous silica.

    PubMed

    Bagheri, Akbar; Behbahani, Mohammad; Amini, Mostafa M; Sadeghi, Omid; Taghizade, Mohsen; Baghayi, Lida; Salarian, Mani

    2012-01-30

    A novel sorbent for simultaneous separation of cadmium and copper was prepared by functionalizing SBA-15 nanoporous silica with diphenylcarbazide. A solid-phase extraction method using the above sorbent has been developed to separate and concentrate trace amount of cadmium and copper ions from environmental samples by flame atomic absorption spectrophotometry measurements. The optimum experimental conditions such as pH, flow rates, type and the smallest amount of eluent for elution of cadmium and copper ions, break through volume and effect of coexisting ions on the separation and determination of cadmium and copper ions were evaluated. The extraction efficiency for cadmium and copper ions were greater than 98% and limit of detection (LOD) was 0.15 and 0.45 ng mL(-1) for cadmium and copper, respectively. The preconcentration factor was 294 and 291 for cadmium and copper, respectively, and the relative standard deviation (RSD) of the method was <4% for 10 separate column experiments for the determination of 5.0 μg cadmium and copper ions. The adsorption capacity of the nanoporous silica was 198 mg g(-1) for cadmium and 105 mg g(-1) for copper on functionalized SBA-15 nanoporous silica. Validation of the outlined method was performed by analyzing certified reference materials (Soil (NCS DC 73323) and ore polymetallic gold Zidarovo-PMZrZ (206 BG 326)). The practical applicability of the developed sorbent was examined using real samples such as sea water, fish and sediment samples. PMID:22284517

  7. Comparison of reactivity of Pt(II) center in the mononuclear and binuclear organometallic diimineplatinum complexes toward oxidative addition of methyl iodide

    NASA Astrophysics Data System (ADS)

    Hashemi, Majid

    2016-01-01

    The reactivities of Pt(II) center in a series of organometallic mononuclear Pt(II), binuclear Pt(II) and binuclear mixed-valence Pt(II)-Pt(IV) complexes toward oxidative addition of MeI have been compared from a theoretical point of view. The nucleophilicity index and electron-donation power were calculated for each of these complexes. The energies of HOMO and dZ2 orbital were determined for these complexes. Very good correlations were found between logk2 (k2 is the experimentally determined second order rate constant for the oxidative addition of MeI on these complexes) and nucleophilicity index or electron-donation power for these complexes. The correlation between logk2 and the energy of HOMO or the energy of dZ2 orbital were also very good. The condensed-to-atom Fukui functions for electrophilic attack on these complexes showed that the Pt(II) center is the preferred site for the oxidative addition of MeI. All of these observations are in agreement with the proposed SN2 type mechanism in the oxidative addition of MeI on the Pt(II) center in these complexes.

  8. Highly effective and stable Ag3PO4-WO3/MWCNTs photocatalysts for simultaneous Cr(VI) reduction and orange II degradation under visible light irradiation

    NASA Astrophysics Data System (ADS)

    Cai, Li; Xiong, Xiaoli; Liang, Ninggang; Long, Qiyi

    2015-10-01

    A series of high-performance photocatalysts of Ag3PO4-WO3/multi-walled carbon nanotubes (MWCNTs) were fabricated through a deposition-precipitation method. Their structures and physical properties were characterized by means of scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), transmission electron microscope (TEM), specific surface analyzer, X-ray diffraction (XRD), UV-vis absorption spectra, photoluminescence spectra (PL) and X-ray photo-electron spectroscopy (XPS). SEM, EDS and TEM analyses verified that Ag3PO4-WO3/MWCNTs composites have been successfully prepared. PL analysis illustrated that Ag3PO4-WO3/MWCNTs have the lower emission peak intensities, compared with Ag3PO4 and WO3. By using simultaneous decontaminations of Cr(VI) and orange II as model reactions, the photocatalytic efficiencies of Ag3PO4, WO3 and Ag3PO4-WO3/MWCNTs were evaluated. The reaction results showed that Ag3PO4-WO3/MWCNTs have strong photocatalytic activities. The effect of Ag3PO4:WO3 ratio on the photocatalytic activity was systemically studied. The catalyst AWM7/3 was found to exhibit the highest photocatalytic activity and excellent chemical stability in repeated and long-term applications. The improvement of photocatalytic activity and stability was mainly attributed to the highly effective separation of photo-generated electron-hole pairs and special transfer pathway of electrons and holes in Ag3PO4-WO3/MWCNTs composites. Therefore, the prepared Ag3PO4-WO3/MWCNTs could act as a high-performance catalyst for the simultaneous decontaminations of Cr(VI) and orange II, and also suggested the promising applications.

  9. Preliminary results of a phase I/II study of simultaneous modulated accelerated radiotherapy for nondisseminated nasopharyngeal carcinoma

    SciTech Connect

    Lee, Sang-wook . E-mail: lsw@amc.seoul.kr; Back, Geum Mun; Yi, Byong Yong; Choi, Eun Kyung; Ahn, Seung Do; Shin, Seong Soo; Kim, Jung-hun; Kim, Sang Yoon; Lee, Bong-Jae; Nam, Soon Yuhl; Choi, Seung-Ho; Kim, Seung-Bae; Park, Jin-hong; Lee, Kang Kyoo; Park, Sung Ho; Kim, Jong Hoon

    2006-05-01

    Purpose: To present preliminary results of intensity-modulated radiotherapy (IMRT) with the simultaneous modulated accelerated radiotherapy (SMART) boost technique in patients with nasopharyngeal carcinoma (NPC). Methods and Materials: Twenty patients who underwent IMRT for nondisseminated NPC at the Asan Medical Center between September 2001 and December 2003 were prospectively evaluated. Intensity-modulated radiotherapy was delivered with the 'step and shoot' SMART technique at prescribed doses of 72 Gy (2.4 Gy/day) to the gross tumor volume, 60 Gy (2 Gy/day) to the clinical target volume and metastatic nodal station, and 46 Gy (2 Gy/day) to the clinically negative neck region. Eighteen patients also received cisplatin once per week. Results: The median follow-up period was 27 months. Nineteen patients completed the treatment without interruption; the remaining patient interrupted treatment for 2 weeks owing to severe pharyngitis and malnutrition. Five patients (25%) had Radiation Therapy Oncology Group Grade 3 mucositis, whereas 9 (45%) had Grade 3 pharyngitis. Seven patients (35%) lost more than 10% of their pretreatment weight, whereas 11 (55%) required intravenous fluids and/or tube feeding. There was no Grade 3 or 4 xerostomia. All patients showed complete response. Two patients had distant metastases and locoregional recurrence, respectively. Conclusion: Intensity-modulated radiotherapy with the SMART boost technique allows parotid sparing, as shown clinically and by dosimetry, and might also be more effective biologically. A larger population of patients and a longer follow-up period are needed to evaluate ultimate tumor control and late toxicity.

  10. Colorimetric Strategy for Highly Sensitive and Selective Simultaneous Detection of Histidine and Cysteine Based on G-Quadruplex-Cu(II) Metalloenzyme.

    PubMed

    Wu, Changtong; Fan, Daoqing; Zhou, Chunyang; Liu, Yaqing; Wang, Erkang

    2016-03-01

    In this present work, we proposed a colorimetric strategy for simultaneous detection of histidine and cysteine based on G-quadruplex-Cu(II) metalloenzyme for the first time. Because of the adding of histidine or cysteine, the formation of G-quadruplex-Cu(II) metalloenzyme will be disturbed, thus the catalytic activity to TMB-H2O2 reaction is inversely proportional to the concentration of histidine or cysteine. With this strategy, the limit of detection in experimental measurement for histidine and cysteine is 10 nM and 5 nM, respectively, which are both lower than previous colorimetric arrays. With the help of NEM, cysteine is alkylated and the reaction between Cu(2+) is inhibited, so the selectivity can also be guaranteed. The cost is quite low since the developed array is label free and enzyme free by using low-cost DNA and Cu(2+). More importantly, the colorimetric detection operation is very simple without any further modification process. PMID:26832965

  11. SeO II addition on PVA-based photopolymer for improving photostorage stabilities and diffraction efficiencies

    NASA Astrophysics Data System (ADS)

    Kim, Daeheum; Nam, Seungwoong; Yeo, Seungbyung; Lim, Jiyun

    2006-08-01

    Polyvinyl alcohol/Acrylamide(PVA/AA)based photopolymer systems modified with SeO II crystals were prepared and photostorage characteristics mainly including diffraction efficiencies were examined and compared with pure PVA/AA films using green laser light (532nm). The photosensitive films were composed of polymeric film-forming binder (PVA), monomer (acrylamide, AA), photoinitiator (triethanol amine, TEA), photosensitizer (Eosin YR), and SeO II crystals. The best optical recording characteristics were observed at the composition of: polymer binder (PVA) : AA : TEA : SeO II : Eosin Y = 1.0 : 0.3 : 0.225 : 0.1 : 0.0015. Diffraction efficiencies as high as 85% with energetic sensitivity of 0.5 mW/cm2 have been obtained in the photopolymer film, and the photopolymer film with SeO II showed higher diffraction efficiencies and lower initial sensitivity than the photopolymer film without SeO II. The morphology of SeO II was expected to be nano crystals since they didn't scatter optical lights and didn't show any peaks in X-ray diffraction spectra.

  12. The effects of simultaneous RNAi suppression of PsbO and PsbP protein expression in photosystem II of Arabidopsis.

    PubMed

    Yi, Xiaoping; Hargett, Stefan R; Frankel, Laurie K; Bricker, Terry M

    2008-01-01

    Interfering RNA was used to suppress simultaneously the expression of the four genes which encode the PsbO and PsbP proteins of Photosystem II in Arabidopsis (PsbO: At5g66570, At3g50820 and PsbP: At1g06680, At2g30790). A phenotypic series of transgenic plants was obtained that expressed variable amounts of the PsbO proteins and undetectable amounts of the PsbP proteins. Immunological studies indicated that the loss of PsbP expression was correlated with the loss of expression of the PsbQ, D2, and CP47 proteins, while the loss of PsbO expression was correlated with the loss of expression of the D1 and CP43 proteins. Q(A)(-) reoxidation kinetics in the absence of DCMU indicated that the slowing of electron transfer from Q(A)(-) to Q(B) was correlated with the loss of the PsbP protein. Q(A)(-) reoxidation kinetics in the presence of DCMU indicated that charge recombination between Q(A)(-) and donor side components of the photosystem was retarded in all of the mutants. Decreasing amounts of the PsbO protein in the absence of the PsbP component also led to a progressive loss of variable fluorescence yield (F(V)/F(M)). During fluorescence induction, the loss of PsbP was correlated with a more rapid O to J transition and a loss of the J to I transition. These results indicate that the losses of the PsbO and PsbP proteins differentially affect separate protein components and different PS II functions and can do so, apparently, in the same plant. PMID:18791808

  13. Simultaneous and sensitive analysis of aliphatic carboxylic acids by ion-chromatography using on-line complexation with copper(II) ion.

    PubMed

    Kemmei, Tomoko; Kodama, Shuji; Yamamoto, Atsushi; Inoue, Yoshinori; Hayakawa, Kazuichi

    2015-01-01

    A new approach to ion chromatography is proposed to improve the UV detection of aliphatic carboxylic acids separated by anion-exchange chromatography. When copper(II) ion added to the mobile phase, it forms complexes with carboxylic acids that can be detected at 240 nm. The absorbance was found to increase with increasing copper(II) ion concentration. The retention times of α-hydroxy acids were also found to depend on the copper(II) ion concentration. Addition of acetonitrile to the mobile phase improved the separation of aliphatic carboxylic acids. The detection limits of the examined carboxylic acids (formate, glycolate, acetate, lactate, propionate, 3-hydroxypropionate, n-butyrate, isobutyrate, n-valerate, isovalerate, n-caproate) calculated at S/N=3 ranged from 0.06 to 3 μM. The detector signal was linear over three orders of magnitude of carboxylic acid concentration. The proposed method was successfully applied to analyze aliphatic carboxylic acids in rainwater and bread. PMID:25523885

  14. Shaping frequency response of a vibrating plate for passive and active control applications by simultaneous optimization of arrangement of additional masses and ribs. Part I: Modeling

    NASA Astrophysics Data System (ADS)

    Wrona, Stanislaw; Pawelczyk, Marek

    2016-03-01

    An ability to shape frequency response of a vibrating plate according to precisely defined demands has a very high practical potential. It can be applied to improve acoustic radiation of the plate for required frequencies or enhance acoustic isolation of noise barriers and device casings by using both passive and active control. The proposed method is based on mounting severaladditional ribs and masses (passive and/or active) to the plate surface at locations followed from an optimization process. This paper, Part I, concerns derivation of a mathematical model of the plate with attached elements in the function of their shape and placement. The model is validated by means of simulations and laboratory experiments, and compared with models known from the literature. This paper is followed by a companion paper, Part II, where the optimization process is described. It includes arrangement of passive elements as well as actuators and sensors to improve controllability and observability measures, if active control is concerned.

  15. Modification of the Structure of Ti-Bearing Mold Flux by the Simultaneous Addition of B2O3 and Na2O

    NASA Astrophysics Data System (ADS)

    Li, Zhongmin; Sun, Yongqi; Liu, Lili; Zhang, Zuotai

    2016-03-01

    The present paper mainly focused on how B2O3 and Na2O additions influenced the structure of the Ti-bearing fluoride-free mold flux and investigated how the boron-related units were affected by Na2O. Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, 11B magic angle spinning-nuclear magnetic resonance (MAS-NMR), and X-ray photoelectron spectroscopy (XPS) were utilized to identify different structural units and to analyze the overall modification of the network by additives. It was found that BO3 was more abundant than BO4 in the flux. In addition, the addition of B2O3 and Na2O was proved to promote conversion from non-ring BO3 to tetrahedral BO4, and this was confirmed by FTIR and 11B MAS NMR analysis. BO3 was a two-dimensional structure unit and contributed to construct a less stable network. With increasing B2O3 content, degree of polymerization of the flux was increased as confirmed by increased fraction of Q 3 in Raman spectra and non-bridging oxygen in XPS. By contrast, the addition of Na2O, which is a strong network breaker, brought about more non-bridging oxygen by breaking the Si-O-Si linkage which was verified by XPS results. Consequently, a less polymerized network was observed by decreasing content of Q 3 from Raman spectra.

  16. Mechanism of Action of the Novel Nickel(II) Complex in Simultaneous Reactivation of the Apoptotic Signaling Networks Against Human Colon Cancer Cells

    PubMed Central

    Samie, Nima; Haerian, Batoul Sadat; Muniandy, Sekaran; Marlina, Anita; Kanthimathi, M. S.; Abdullah, Norbani B.; Ahmadian, Gholamreza; Aziddin, Raja E. R.

    2016-01-01

    The aim of this study was to evaluate the cytotoxic potential of a novel nickel(II) complex (NTC) against WiDr and HT-29 human colon cancer cells by determining the IC50 using the standard MTT assay. The NTC displayed a strong suppressive effect on colon cancer cells with an IC50 value of 6.07 ± 0.22 μM and 6.26 ± 0.13 μM against WiDr and HT-29 respectively, after 24 h of treatment. Substantial reduction in the mitochondrial membrane potential and increase in the release of cytochrome c from the mitochondria directed the induction of the intrinsic apoptosis pathway by the NTC. Activation of this pathway was further evidenced by significant activation of caspase 3/7 and 9. The NTC was also shown to activate the extrinsic pathway of apoptosis via activation of caspase-8 which is linked to the suppression of NF-κB translocation to the nucleus. Cell cycle arrest in the G1 phase was confirmed by flow cytometry and up-regulation of glutathione reductase expression was quantified by qPCR. Results of the current work indicates that NTC possess a potent cancer cell abolishing activity by simultaneous induction of intrinsic and extrinsic pathways of apoptosis in colon cancer cell lines. PMID:26858642

  17. Simultaneous removal of Ni(II), As(III), and Sb(III) from spiked mine effluent with metakaolin and blast-furnace-slag geopolymers.

    PubMed

    Luukkonen, Tero; Runtti, Hanna; Niskanen, Mikko; Tolonen, Emma-Tuulia; Sarkkinen, Minna; Kemppainen, Kimmo; Rämö, Jaakko; Lassi, Ulla

    2016-01-15

    The mining industry is a major contributor of various toxic metals and metalloids to the aquatic environment. Efficient and economical water treatment methods are therefore of paramount importance. The application of natural or low-cost sorbents has attracted a great deal of interest due to the simplicity of its process and its potential effectiveness. Geopolymers represent an emerging group of sorbents. In this study, blast-furnace-slag and metakaolin geopolymers and their raw materials were tested for simultaneous removal of Ni(II), As(III) and Sb(III) from spiked mine effluent. Blast-furnace-slag geopolymer proved to be the most efficient of the studied materials: the experimental maximum sorption capacities for Ni, As and, Sb were 3.74 mg/g, 0.52 mg/g, and 0.34 mg/g, respectively. Although the capacities were relatively low due to the difficult water matrix, 90-100% removal of Ni, As, and Sb was achieved when the dose of sorbent was increased appropriately. Removal kinetics fitted well with the pseudo-second-order model. Our results indicate that geopolymer technology could offer a simple and effective way to turn blast-furnace slag to an effective sorbent with a specific utilization prospect in the mining industry. PMID:26598283

  18. Flux Transfer Events Simultaneously Observed by Polar and Cluster: Flux Rope in the Subsolar Region and Flux Tube Addition to the Polar Cusp

    NASA Technical Reports Server (NTRS)

    Le, G.; Zheng, Y.; Russell, C. T.; Pfaff, R. F.; Lin, N.; Slavin, J. A.; Parks, G.; Wilber, M.; Petrinec, S. M.; Lucek, E. A.; Reme, H.

    2007-01-01

    The phenomenon called flux transfer events (FTEs) is widely accepted as the manifestation of time-dependent reconnection. In this paper, we present observational evidence of a flux transfer event observed simultaneously at low-latitude by Polar and at high-latitude by Cluster. This event occurs on March 21, 2002, when both Cluster and Polar are located near local noon but with a large latitudinal separation. During the event, Cluster is moving outbound from the polar cusp to the magnetosheath, and Polar is in the magnetosheath near the equatorial magnetopause. The observations show that a flux transfer event occurs between the equator and the northern cusp. Polar and Cluster observe the FTE s two open flux tubes: Polar encounters the southward moving flux tube near the equator; and Cluster the northward moving flux tube at high latitude. The low latitude FTE appears to be a flux rope with helical magnetic field lines as it has a strong core field and the magnetic field component in the boundary normal direction exhibits a strong bi-polar variation. Unlike the low-latitude FTE, the high-latitude FTE observed by Cluster does not exhibit the characteristic bi-polar perturbation in the magnetic field. But the plasma data clearly reveal its open flux tube configuration. It shows that the magnetic field lines have straightened inside the FTE and become more aligned to the neighboring flux tubes as it moves to the cusp. Enhanced electrostatic fluctuations have been observed within the FTE core, both at low- and high-latitudes. This event provides a unique opportunity to understand high-latitude FTE signatures and the nature of time-varying reconnection.

  19. Enhancement of antimicrobial activities of whole and sub-fractionated white tea by addition of copper (II) sulphate and vitamin C against Staphylococcus aureus; a mechanistic approach

    PubMed Central

    2011-01-01

    Background Enhancement of antimicrobial plant products e.g. pomegranate extract by copper (II) sulphate is known. Such combinations have applications in various settings, including the identification of novel compositions to study, treat and control infection. Methods A combination of white tea (WT) (made allowing 10 minutes infusion time at 100°C) was combined with 4.8 mM copper (II) sulphate and tested for antimicrobial effect on the viability of Staphylococcus aureus NCTC 06571. Comparisons were made with green (GT) and black (BT) teas. A WT sub-fraction (WTF < 1000 Da) was tested with copper (II) sulphate and 4.8 mM vitamin C. pH measurements of samples were taken for controls and to observe any changes due to tea/agent interaction. Catalase was used to investigate hydrogen peroxide release. UV-vis. was used to compare WT and WTF. Results A 30 minute incubation at room temperature of copper (II) sulphate alone and combined with WT reduced the viability of S. aureus NCTC 06571 by c.a 1 log10 cfu mL-1. GT and BT with copper (II) sulphate negated activity to buffer values. Combined with copper (II) sulphate, vitamin C, WTF and, vitamin C plus WTF all reduced the viability of S. aureus NCTC 06571 by c.a. 3.5 log10 cfu mL-1. Independent experiments showed the results were not due to pH effects. Adding WT or WTF to copper (II) sulphate resulted in increased acidity. Copper (II) sulphate alone and combined with WT required c.a 300 μg mL-1 (final concentration) catalase to restore S. aureus viability, WTF with copper (II) sulphate and added vitamin C required c.a 600 μg mL-1. WT and WTF UV-visible spectra were similar. Conclusions WT showed no efficacy in the combinations tested. WTF was enhanced with copper (II) sulphate and further with vitamin C. WT and WTF increased acidity of copper (II) sulphate possibly via the formation of chemical complexes. The difference in WT/WTF absorbance possibly represented substances less concentrated or absent in WTF

  20. Modeling and simulation of NO{sub x}/SO{sub 2} removal in an aqueous scrubber system using the additive fE(ii)*EDTA

    SciTech Connect

    Li, W.; Mendelsohn, M.; Harkness, J.B.L.; Livengood, C.D.

    1996-02-01

    Addition of the metal chelate anion Fe(II)*EDTA{sup 2+} has been shown to increase the amount of gaseous NO{sub x} absorbed from a gas stream containing SO{sub 2}, where an aqueous scrubbing process is used to treat the gas. Recently, we published and presented data on improved systems for NO{sub x} removal that incorporate an antioxidant and/or reducing agent in the process, together with the Fe(II)*EDTA. In this paper, a mathematical model describing NO{sub x} removal as a function of the square root of Fe(II)*EDTA concentration in the solution and of the operating conditions is derived and validated.

  1. Simultaneous determination of antioxidants, preservatives and sweetener additives in food and cosmetics by flow injection analysis coupled to a monolithic column.

    PubMed

    García-Jiménez, J F; Valencia, M C; Capitán-Vallvey, L F

    2007-07-01

    Today it is common to find samples with various additives from several families. This is the case of sweeteners, preservatives and antioxidants. We have selected a set of additives broadly used in foods and cosmetics with an ample variety of polarities, namely: aspartame (AS), acesulfame (AK)/saccharin (SA), methylparaben (MP), ethylparaben (EP), propylparaben (PP), butylparaben (BP), propylgallate (PG) and butylhydroxyanisole (BA). The monolithic column used as separative system is a 5 mm commercial precolumn of silica C18 coupled to a flow injection manifold working with a peristaltic pump. The mixture was separated in only 400 s with resolution factors greater than 1.1 in all cases. To achieve the separation in the FIA system we used two carriers: first, a mixture of ACN/water buffered with 10 mM pH 6.0 phosphate buffer and second, a methanol:water mixture to improve the carrier strength and speed up the more apolar analytes at 3.5 mL min(-1). Detection is accomplished by means of a diode array spectrometer at the respective wavelength of each compound. The comparison of the analytical parameters obtained for this procedure with a standard HPLC method validates our new method, obtaining a method that is quick, with high repeatability and reproducibility and with good resolution between analytes. We have successfully applied the method to real food and cosmetics samples. PMID:17586119

  2. C-selective and diastereoselective alkyl addition to β,γ-alkynyl-α-imino esters with zinc(II)ate complexes.

    PubMed

    Hatano, Manabu; Yamashita, Kenji; Mizuno, Mai; Ito, Orie; Ishihara, Kazuaki

    2015-02-23

    Since umpolung α-imino esters contain three electrophilic centers, regioselective alkyl addition with traditional organometallic reagents has been a serious problem in the practical synthesis of versatile chiral α-amino acid derivatives. An unusual C-alkyl addition to α-imino esters using a Grignard reagent (RMgX)-derived zinc(II)ate was developed. Zinc(II)ate complexes consist of a Lewis acidic [MgX](+) moiety, a nucleophilic [R3 Zn](-) moiety, and 2 [MgX2 ]. Therefore, the ionically separated [R3 Zn](-) selectively attacks the imino carbon atom ,which is most strongly activated by chelation of [MgX](+) . In particular, chiral β,γ-alkynyl-α-imino esters can strongly promote highly regio- and diastereoselective C-alkylation because of structural considerations, and the corresponding optically active α-quaternary amino acid derivatives are obtained within 5 minutes in high to excellent yields. PMID:25598353

  3. Ionic liquid as a mobile phase additive in high-performance liquid chromatography for the simultaneous determination of eleven fluorescent whitening agents in paper materials.

    PubMed

    Wang, Qing; Chen, Xianbo; Qiu, Bin; Zhou, Liang; Zhang, Hui; Xie, Juan; Luo, Yan; Wang, Bin

    2016-04-01

    In the present study, 11 4,4'-diaminostilbene-2,2'-disulfonic acid based fluorescent whitening agents with different numbers of sulfonic acid groups were separated by using an ionic liquid as a mobile phase additive in high-performance liquid chromatography with fluorescence detection. The effects of ionic liquid concentration, pH of mobile phase B, and composition of mobile phase A on the separation of fluorescent whitening agents were systematically investigated. The ionic liquid tetrabutylammonium tetrafluoroborate is superior to tetrabutylammomnium bromide for the separation of the fluorescent whitening agents. The optimal separation conditions were an ionic liquid concentration at 8 mM and the pH of mobile phase B at 8.5 with methanol as mobile phase A. The established method exhibited low limits of detection (0.04-0.07 ng/mL) and wide linearity ranges (0.30-20 ng/mL) with high linear correlation coefficients from 0.9994 to 0.9998. The optimized procedure was applied to analyze target analytes in paper samples with satisfactory results. Eleven target analytes were quantified, and the recoveries of spiked paper samples were in the range of 85-105% with the relative standard deviations from 2.1 to 5.1%. The obtained results indicated that the method was efficient for detection of 11 fluorescent whitening agents. PMID:26843408

  4. Simultaneous determination of fangchinoline and tetrandrine in Stephania tetrandra S. Moore by using 1-alkyl-3-methylimidazolium-based ionic liquids as the RP-HPLC mobile phase additives.

    PubMed

    Tang, Yan; Sun, Ailing; Liu, Renmin; Zhang, Yongqing

    2013-03-12

    A reversed phase high performance liquid chromatography (RP-HPLC) method for simultaneous determination of fangchinoline (FAN) and tetrandrine (TET) in Stephania tetrandra S. Moore was established by using 1-hexyl-3-methylimidazolium tetrafluoroborate as the mobile phase additives in this paper. Four types of 1-alkyl-3-methylimidazolium-based ionic liquids (ILs) were used as additives of the mobile phase to separate FAN and TET by RP-HPLC. The effects of the length of the alkyl group on the imidazolium ring and its counterion, the concentrations of IL and the pH of the mobile phase, which influenced the chromatographic behaviors of FAN and TET, were investigated in detail. The linearity, sensitivity, accuracy and repeatability of the proposed method were also investigated. The probable mechanism of the separation with ILs as the mobile phase additives was explored and discussed. PMID:23452799

  5. Indole synthesis by conjugate addition of anilines to activated acetylenes and an unusual ligand-free copper(II)-mediated intramolecular cross-coupling.

    PubMed

    Gao, Detian; Back, Thomas G

    2012-11-12

    A versatile new synthesis of indoles was achieved by the conjugate addition of N-formyl-2-haloanilines to acetylenic sulfones, ketones, and esters followed by a copper-catalyzed intramolecular C-arylation. The conjugate addition step was conducted under exceptionally mild conditions at room temperature in basic, aqueous DMF. Surprisingly, the C-arylation was performed most effectively by employing copper(II) acetate as the catalyst in the absence of external ligands, without the need for protection from air or water. An unusual feature of this process, for the case of acetylenic ketones, is the ability of the initial conjugate-addition product to serve as a ligand for the catalyst, which enables it to participate in the catalysis of its further transformation to the final indole product. Mechanistic studies, including EPR experiments, indicated that copper(II) is reduced to the active copper(I) species by the formate ion that is produced by the base-catalyzed hydrolysis of DMF. This process also served to recycle any copper(II) that was produced by the adventitious oxidation of copper(I), thereby preventing deactivation of the catalyst. Several examples of reactions involving acetylenic sulfones attached to a modified Merrifield resin demonstrated the feasibility of solid-phase synthesis of indoles by using this protocol, and tricyclic products were obtained in one pot by employing acetylenic sulfones that contain chloroalkyl substituents. PMID:23019064

  6. 78 FR 32224 - Availability of Version 3.1.2 of the Connect America Fund Phase II Cost Model; Additional...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-05-29

    ... as part of the Model Design PN, 77 FR 38804, June 29, 2012, of the possible significant economic...). See Electronic Filing of Documents in Rulemaking Proceedings, 63 FR 24121, May 1, 1998. Electronic...; Additional Discussion Topics in Connect America Cost Model Virtual Workshop AGENCY: Federal...

  7. Effects of chemical mechanical planarization slurry additives on the agglomeration of alumina nanoparticles II: aggregation rate analysis.

    PubMed

    Brahma, Neil; Talbot, Jan B

    2014-04-01

    The aggregation rate and mechanism of 150 nm alumina particles in 1mM KNO3 with various additives used in chemical mechanical planarization of copper were investigated. The pH of each suspension was ∼8 such that the aggregation rate was slow enough to be measured and analyzed over ∼120 min. In general, an initial exponential growth was observed for most suspensions indicating reaction-limited aggregation. After aggregate sizes increase to >500 nm, the rate followed a power law suggesting diffusion-limited aggregation. Stability ratios and fractal dimension numbers were also calculated to further elucidate the aggregation mechanism. PMID:24491325

  8. EXPERIMENTAL EPIDEMIOLOGY : II. EFFECT OF THE ADDITION OF HEALTHY MICE TO A POPULATION SUFFERING FROM MOUSE TYPHOID.

    PubMed

    Amoss, H L

    1922-06-30

    1. A kind of mouse village was set up into which was introduced a small number of mice fed on a culture of so called mouse typhoid (Bacillus pestis cavice of the Bacillus paratyphosus B group) bacillus. The spread of the infection so induced to the cages, or "homes," of the other mice was left to accident through the attendant who fed the animals and cleaned the cages. That this means was likely to be sufficient was deduced from the epidemic reported by Lynch. A spot map was kept throughout the experiments which extended from 1919 into 1922. 2. The first effect of the exposure of normal mice to a much smaller number of mice fed on the culture is to set up a sporadic, not an epidemic outbreak of mouse typhoid. This is the regularly recurring incident of the experiment as shown by low mortality and low cage attack rate. Such a sporadic prevalence is self-limited in time. 3. The introduction of fresh, normal mice into a community in which sporadic deaths are occurring leads regularly, not to the further extension of the sporadic deaths, but to an epidemic spread, as shown by high mortality and high cage attack rate. The epidemic begins with deaths among the new mice, but extends to the old mice which succumb later. The spread ceases and the wave subsides before all the mice have succumbed. A state of equilibrium between the infecting bacillus and the surviving mice is reached; no more deaths occur. The epidemic outbreak, therefore, is also self-limited in time. 4. If, now, another new addition of normal mice is brought into the potentially infected community, the events are reenacted; deaths occur among the new, another epidemic wave sweeps through the population, again claiming victims among the previous survivors. Through the replacement of the destroyed mice with fresh, normal mice, epidemic wave after wave is produced, until certain groups of old survivors are entirely wiped out. There seems to be no limit to this process, as there will always be survivors at

  9. Simultaneous XMM-Newton and HST-COS observation of 1H 0419-577. II. Broadband spectral modeling of a variable Seyfert galaxy

    NASA Astrophysics Data System (ADS)

    Di Gesu, L.; Costantini, E.; Piconcelli, E.; Ebrero, J.; Mehdipour, M.; Kaastra, J. S.

    2014-03-01

    In this paper, we present the longest exposed (97 ks) XMM-Newton EPIC-pn spectrum ever obtained for the Seyfert 1.5 galaxy1H 0419-577. With the aim of explaining the broadband emission of this source, we took advantage of the simultaneous coverage in the optical/UV that was provided in the present case by the XMM-Newton Optical Monitor and by a HST-COS observation. Archival FUSE flux measurements in the far-ultraviolet were also used for the present analysis. We successfully modeled the X-ray spectrum and the optical/UV fluxes data points using a Comptonization model. We found that a blackbody temperature of T ~ 56 eV accounts for the optical/UV emission originating in the accretion disk. This temperature serves as an input for the Comptonized components that model the X-ray continuum. Both a warm (Twc ~ 0.7 keV, τwc ~ 7) and a hot corona (Thc ~ 160 keV, τhc ~ 0.5) intervene to upscatter the disk photons to X-ray wavelengths. With the addition of a partially covering (Cv ~ 50%) cold absorber with a variable opacity ( NH~ [1019-1022] cm-2), this model can also explain the historical spectral variability of this source, with the present dataset presenting the lowest one ( NH~1019 cm-2). We discuss a scenario where the variable absorber becomes less opaque in the highest flux states because it gets ionized in response to the variations of the X-ray continuum. The lower limit for the absorber density derived in this scenario is typical for the broad line region clouds. We infer that1H 0419-577may be viewed from an intermediate inclination angle i ≥ 54°, and, on this basis, we speculate that the X-ray obscuration may be associated with the innermost dust-free region of the obscuring torus. Finally, we critically compare this scenario with all the different models (e.g., disk reflection) that have been used in the past to explain the variability of this source.

  10. Simultaneous determination of nickel and copper by H-point standard addition method-first-order derivative spectrophotometry in plant samples after separation and preconcentration on modified natural clinoptilolite as a new sorbent.

    PubMed

    Roohparvar, Rasool; Taher, Mohammad Ali; Mohadesi, Alireza

    2008-01-01

    For the simultaneous determination of nickel(ll) and copper(ll) in plant samples, a rapid and accurate method was developed. In this method, solid-phase extraction (SPE) and first-order derivative spectrophotometry (FDS) are combined, and the result is coupled with the H-point standard addition method (HPSAM). Compared with normal spectrophotometry, derivative spectrophotometry offers the advantages of increased selectivity and sensitivity. As there is no need for carrying out any pretreatment of the sample, the spectrophotometry method is easy, but because of a high detection limit, it is not so practical. In order to decrease the detection limit, it is suggested to combine spectrophotometry with a preconcentration method such as SPE. In the present work, after separation and preconcentration of Ni(ll) and Cu(ll) on modified clinoptilolite zeolite that is loaded with 2-[1-(2-hydroxy-5-sulforphenyl)-3-phenyl-5-formaza-no]-benzoic acid monosodium salt (zincon) as a selective chromogenic reagent, FDS-HPSAM, which is a simple and selective spectrophotometric method, has been applied for simultaneous determination of these ions. With optimum conditions, the detection limit in original solutions is 0.7 and 0.5 ng/mL, respectively, for nickel and copper. The linear concentration ranges in the proposed method for nickel and copper ions in original solutions are 1.1 to 3.0 x 10(3) and 0.9 to 2.0 x 10(3) ng/mL, respectively. The recommended procedure is applied to successful determination of Cu(ll) and Ni(ll) in standard and real samples. PMID:18567311

  11. Rotational modulation and flares on RS Canum Venaqticorum and BY Draconis stars. XII - Near-to-simultaneous high resolution UV and optical observations of II Pegasi during July 1984

    NASA Astrophysics Data System (ADS)

    Byrne, P. B.; Panagi, P.; Doyle, J. G.; Englebrecht, C. A.; McMahan, R.; Marang, F.; Wegner, G.

    1989-04-01

    Nearly simultaneous high resolution ground-based optical and IUE satellite UV spectroscopy and an optical light curve of the RS CVn star II Peg are presented. It is shown that the chromospheric and transition region radiative losses of the star in July 1984 are lower than previously recorded means. The flux in the Lyman-alpha line is estimated and evidence is given for variability in all of the emission lines. This variability appears to be correlated with the optical spots. Line profiles at two rotational phases for the principal UV emission lines show an excess broadening over and above the combined instrumental plus Doppler broadening.

  12. Simultaneous Measurements of Lower E-region Nighttime Electrodynamics Gathered with Rockets at the Altair Radar During the EQUIS II Campaign at Kwajalein Atoll

    NASA Astrophysics Data System (ADS)

    Pfaff, R.; Rowland, D.; Acuna, M.; Freudenreich, H.; Kudeki, E.; Larsen, M.; Clemmons, J.; Bishop, R.; Steigies, C.; Chau, J.; Sarango, M.

    2005-05-01

    In order to investigate the complex electrodynamics and neutral-plasma coupling inherent to the unstable nighttime E-region near the earth's magnetic equator, a series of rocket/radar experiments were conducted at Kwajalein Atoll (9.4 deg N, 167.5 deg E) near 5 degrees magnetic latitude in September, 2004, as part of the NASA EQUIS II Campaign. The rocket experiments consisted of two identical, instrumented payloads launched on separate nights with limited apogees so that the payloads "hovered" in the E region below 120 km. Each payload included vector DC and AC electric field detectors, a flux-gate DC magnetometer, a combined Langmuir probe/impedance probe to measure the absolute plasma density and its variations, multi-sensor ionization gauges to measure the neutral density and its variations, and spaced-electric field receivers to measure the wavelength and phase velocity of the unstable plasma waves. Separate rockets launched in conjunction with the instrumented rockets released TMA trails on the upleg and downleg between roughly 90-160 km that revealed the neutral wind and its velocity shear. These payloads also included a beacon experiment that provided an independent measure of the plasma density. In addition to the rocket experiments, coherent and incoherent scatter radar measurements at 160 MHz and 422 MHz were gathered with the fully steerable Altair radar and detected layers of backscatter echoes near 105 km that were both intense and sporadic in their appearance. The layers were narrow in their altitude extent, spatially modulated, and typically lasted for about 30 minutes. The payloads were launched into unstable layers on two nights, one prior to the pre-reversal enhancement (LT 20:00:45) and one near midnight (LT 23:43:53). The initial electric field and plasma density data reveal well-defined layers of waves between 95-105 km altitude with predominant wavelengths of 10's of meters and longer within regions that contained weak to moderate gradients

  13. Non-ionic surfactant modified ligand exchange chromatography using copper (II) complex of N,N-dimethyl-L-phenylalanine as the chiral additive for enantioselective amino acids separation.

    PubMed

    Dimitrova, Pepa; Bart, Hans-Jörg

    2010-03-17

    The influence of non-ionic surfactants on the selectivity and retention in the ligand exchange chromatography for the enantioselective separation of racemic mixtures of the amino acids dl-methionine, dl-leucine, dl-valine and dl-tyrosine applying chiral mobile phases was investigated, whereas five different surfactants were tested as modifiers. The experiments were carried out using a commercially available non-chiral RP-C8 column and the copper (II) complex of N,N-dimethyl-l-phenylalanine as the chiral additive. Varying the surfactant concentrations the retention factors and the selectivity could be controlled and in general no negative influence on the separation (due to surfactant adsorption on the non-chiral stationary phase) occurred. Changing the temperature the van't Hoff plots were obtained and the thermodynamic parameters calculated. Temperature had influence on the selectivity for each surfactant and lowered the retention times as expected. PMID:20172105

  14. Localization of eight additional genes in the human major histocompatibility complex, including the gene encoding the casein kinase II {beta} subunit (CSNK2B)

    SciTech Connect

    Albertella, M.R.; Jones, H.; Thomson, W.

    1996-09-01

    A wide range of autoimmune and other diseases are known to be associated with the major histocompatibility complex. Many of these diseases are linked to the genes encoding the polymorphic histocompatibility complex. Many of these diseases are linked to the genes encoding the polymorphic histocompatibility antigens in the class I and class II regions, but some appear to be more strongly associated with genes in the central 1100-kb class III region, making it important to characterize this region fully for the presence of novel genes. An {approximately}220-kb segment of DNA in the class III region separating the Hsp70 (HSPA1L) and BAT1 (D6S8IE) genes, which was previously known to contain 14 genes. Genomic DNA fragments spanning the gaps between the known genes were used as probes to isolate cDNAs corresponding to five new genes within this region. Evidence from Northern blot analysis and exon trapping experiments that suggested the presence of at least two more new genes was also obtained. Partial cDNA and complete exonic genomic sequencing of one of the new genes has identified it as the casein kinase II{beta} subunit (CSNK2B). Two of the other novel genes lie within a region syntenic to that implicated in susceptibility to experimental allergic orchitis in the mouse, an autoimmune disease of the testis, and represent additional candidates for the Orch-1 locus associated with this disease. In addition, characterization of the 13-kb intergenic gap separating the RD (D6545) and G11 (D6S60E) genes has revealed the presence of a gene encoding a 1246-amino-acid polypeptide that shows significant sequence similarity to the yeast anti-viral Ski2p gene product. 49 refs., 8 figs.

  15. Halogen-free ionic liquid as an additive in zinc(II)-selective electrode: surface analyses as correlated to the membrane activity.

    PubMed

    Al-Asousi, Maryam F; Shoukry, Adel F; Bu-Olayan, Abdul Hadi

    2012-05-30

    Two conventional Zn(II) polyvinyl chloride (PVC) membrane electrodes have been prepared and characterized. They were based on dibenzo-24-crown-8 (DBC) as a neutral carrier, dioctyl phthalate (DOP) as a plasticizer, and potassium tetrakis (p-chlorophenyl) borate, KTpClPB or the halogen-free ionic liquid, tetraoctylammonium dodecylbenzene sulfonate [TOA][DBS] as an additive. The use of ionic liquid has been found to enhance the selectivity of the sensor. For each electrode, the surfaces of two membranes were investigated using X-ray photoelectron, ion-scattering spectroscopy and atomic force microscopy. One of the two membranes was conditioned by soaking it for 24 h in a 1.0×10(-3) M Zn(NO(3))(2) solution and the second was soaked in bi-distilled water for the same interval (24 h). Comparing the two surfaces indicated the following: (a) the high selectivity in case of using [TOA][DBS] as an additive is due to the extra mediation caused by the ionic liquid and (b) the working mechanism of the electrode is based on phase equilibrium at the surface of the membrane associated with ion transport through the bulk of the membrane. PMID:22608433

  16. Addition of niclosamide to palladium(II) saccharinate complex of terpyridine results in enhanced cytotoxic activity inducing apoptosis on cancer stem cells of breast cancer.

    PubMed

    Karakas, Didem; Cevatemre, Buse; Aztopal, Nazlihan; Ari, Ferda; Yilmaz, Veysel Turan; Ulukaya, Engin

    2015-09-01

    Wnt signaling is one of the core signaling pathways of cancer stem cells (CSCs). It is re-activated in CSCs and plays essential role in the survival, self-renewal and proliferation of these cells. Therefore, we aimed to evaluate the cytotoxic effects of palladium(II) complex which is formulated as [PdCl(terpy)](sac)2H2O and its combination with niclosamide which is an inhibitor of Wnt signaling pathway associated with breast cancer stem cells. Characteristic cell surface markers (CD44(+)/CD24(-)) were determined by flow cytometry in CSCs. ATP viability assay was used to determine the cytotoxic activity. The mode of cell death was evaluated morphologically using fluorescence microscopy and biochemically using M30 ELISA assay as well as performing qPCR. Our study demonstrated that the combination of niclosamide (1.5 μM) and Pd(II) complex (12.5, 25 and 50 μM) at 48 h has enhanced cytotoxic activity resulted from the induction of apoptosis (indicated by the presence of pyknotic nuclei, increments in M30 and over expression of proapoptotic genes of TNFRSF10A and FAS). Importantly, the addition of niclosamide resulted in the suppression of autophagy (proved by the decrease in ATG5 gene levels) that might have contributed to the enhanced cytotoxicity. In conclusion, the application of this combination may be regarded as a novel and effective approach for the treatment of breast cancer due to its promising cytotoxic effect on cancer stem cells that cause recurrence of the disease. PMID:26234907

  17. Simultaneous existence of cinnamomin (a type II RIP) and small amount of its free A- and B-chain in mature seeds of camphor tree.

    PubMed

    Hou, Fa-Jian; Xu, Hong; Liu, Wang-Yi

    2003-04-01

    Cinnamomin, a type II ribosome-inactivating protein (RIP), was isolated from the mature seeds of camphor tree (Cinnamomum camphora). In this paper, small amount of free A- and B-chain of cinnamomin were found to be present in the mature seed cell of C. camphora besides the intact cinnamomin. Our results demonstrated that camphorin, a type I RIP previously reported to coexist with cinnamomin in the seeds of C. camphora, actually was the A-chain of cinnamomin. The percentage of free A- and B-chain in the total cinnamomin was 2.6-2.8% in the seed extract. Of these free A- and B-chain approximate 80% already existed in the seed cell, only about 20% were produced during the purification operation. As the enzymatic activity to reduce disulfide bond of cinnamomin in the seed extract of C. camphora was detected, we proposed that the free A- and B-chain were derived from the enzymatic reduction of the interchain disulfide bond of cinnamomin. It was demonstrated that the endogenous type II RIPs of several plant species, such as Cinnamomum porrectum, Cinnamomum bodinieri and Ricinus communis, could be enzymatically reduced into the free A- and B-chain in their respective seed cells. The function of the free A-chain in the seed cell and the possibility that metabolic enzymes might be involved in the reduction of the interchain disulfide bond of type II RIPs in vivo are discussed. PMID:12565707

  18. Simultaneous Observation of Melt Flow and Motion of Equiaxed Crystals During Solidification Using a Dual Phase Particle Image Velocimetry Technique. Part II: Relative Velocities

    NASA Astrophysics Data System (ADS)

    Kharicha, Abdellah; Stefan-Kharicha, Mihaela; Ludwig, Andreas; Wu, Menghuai

    2013-02-01

    A two-camera Particle Image Velocimetry (PIV) technique is applied to study the flow pattern and the equiaxed crystal motion during an equiaxed/columnar solidification process of Ammonium Chloride in a die cast cell. This technique is able to measure simultaneously the liquid and the equiaxed grain velocity pattern as already shown in Part I of this paper. The interaction between the equiaxed grains and the melt flow was explored by means of relative velocities. In single isolated configurations, the settling velocity of equiaxed crystal was found to be 41 times smaller than spheres of equivalent size. The coupling between the fluid flow and the equiaxed crystals was found to be important in areas of high crystal density. Chaotic and turbulent behaviors are found to be damped in regions of high equiaxed crystal density.

  19. Radioprotective effectiveness and toxicity of ATP, AET and serotonin applied individually or simultaneously to mice. II. Dose depending protection by single agents.

    PubMed

    Benova, D

    1976-03-01

    The work reported was done as a part of a detailed study on the antiradiation effects of three chemical agents-ATP, AET and serotonin-given individually or simultaneously, the ultimate aim being the identification of an optimally effective and non-toxic dose ratio for the triple combination of protectants. Individual PD50 (protectant dose ensuring 50% survival after lethal irradiation) values were found to be 166 mg/kg and 37 mg/kg for AET and serotonin, respectively. ATP was most effective (45% of 30-day-survival) at 1200 mg/kg in face of a level of X-irradiation above the minimum lethal dose. Some sex differences were observed in protection provided by everyone of the three agents, females being more susceptible to the protective action. PMID:1258098

  20. Short-term climate variability and atmospheric teleconnections from satellite-observed outgoing longwave radiation. I Simultaneous relationships. II - Lagged correlations

    NASA Technical Reports Server (NTRS)

    Lau, K.-M.; Chan, P. H.

    1983-01-01

    Attention is given to the low-frequency variability of outgoing longwave radiation (OLR) fluctuations, their possible correlations over different parts of the globe, and their relationships with teleconnections obtained from other meteorological parameters, for example, geopotential and temperature fields. Simultaneous relationships with respect to the Southern Oscillation (Namais, 1978; Barnett, 1981) signal and the reference OLR fluctuation over the equatorial central Pacific are investigated. Emphasis is placed on the relative importance of the Southern Oscillation (SO) signal over preferred regions. Using lag cross-correlation statistics, possible lagged relationships between the tropics and midlatitudes and their relationships with the SO are then investigated. Only features that are consistent with present knowledge of the dynamics of the system are emphasized. Certain features which may not meet rigorous statistical significance tests but yet are either expected a priori from independent observations or are predicted from dynamical theories are also explored.

  1. Effects of silver and group II fluoride solid lubricant additions to plasma-sprayed chromium carbide coatings for foil gas bearings to 650 C

    NASA Technical Reports Server (NTRS)

    Wagner, R. C.; Sliney, Harold E.

    1986-01-01

    A new self-lubricating coating composition of nickel aluminide-bonded chromium carbide formulated with silver and Group II fluorides was developed in a research program on high temperature solid lubricants. One of the proposed applications for this new coating composition is as a wide temperature spectrum solid lubricant for complaint foil gas bearings. Friction and wear properties were obtained using a foil gas bearing start-stop apparatus at temperatures from 25 to 650 C. The journals were Inconel 748. Some were coated with the plasma sprayed experimental coating, others with unmodified nickel aluminide/chromium carbide as a baseline for comparison. The additional components were provided to assist in achieving low friction over the temperature range of interest. Uncoated, preoxidized Inconel X-750 foil bearings were operated against these surfaces. The foils were subjected to repeated start/stop cycles under a 14-kPa (2-Psi) bearing unit loading. Sliding contact occurred during lift-off and coastdown at surface velocities less than 6 m/s (3000 rPm). Testing continued until 9000 start/stop cycles were accumulated or until a rise in starting torque indicated the journal/bearing had failed. Comparison in coating performance as well as discussions of their properties and methods of application are given.

  2. A pre-clinical pharmacokinetic study in rats of three naturally occurring iridoid glycosides, Picroside-I, II and III, using a validated simultaneous HPLC-MS/MS assay.

    PubMed

    Zhu, Jianwei; Xue, Bingyang; Ma, Bo; Zhang, Qi; Liu, Ming; Liu, Lei; Yao, Di; Qi, Huanhuan; Wang, Yonglu; Ying, Hanjie; Wu, Zimei

    2015-07-01

    A selective and sensitive high-performance liquid chromatography-electro-spray ionization tandem mass spectrometry (LC-ESI-MS/MS) method was developed for the simultaneous quantitative determination of Picroside-I, II, and III in rat plasma and tissue homogenate to aid the pre-clinical studies. The chromatographic separation was performed on a Hypersil GOLD AQ C18 column using a gradient elution program with a mobile phase consisting of 2mM ammonium acetate and acetonitrile. The detection was achieved using a triple quadrupole tandem MS in negative ionization multiple reaction monitoring (MRM) mode. One-step protein precipitation was selected for plasma and tissue sample preparation while liquid-liquid extraction failed to achieve satisfactory recoveries. The calibration curves of all three analytes in either plasma or tissue homogenate showed good linearity over the concentration range of 0.5-500ng/mL with a limit of quantitation at 0.5ng/mL. Both the intra- and inter-day accuracy and precision were within ±10%. The extraction recoveries were >70%, and the relative matrix effect ranged from 80.4% to 107.4% in all the biological samples. All the analytes were stable in matrices for at least 24h at room temperature, or 21 days in frozen. Three freeze/thaw cycles did not cause degradation. The method was successfully applied for quantification of the three iridoid glycosides in the collected plasma and various tissues following intravenous administration in rats. Picroside-I, II, and III were all eliminated rapidly with large volume of distribution. Among the three glycosides, Picroside-II showed the highest liver uptake, and only Picroside-I and II were found to get across the blood brain barrier (BBB). These results were consistent with their hepatoprotective or neuroprotective effects reported clinically. With the aid of the efficient and reliable simultaneous LC-ESI-MS/MS assay this pharmacokinetic study provided insights into their therapeutic targets of these

  3. Short course radiotherapy with simultaneous integrated boost for stage I-II breast cancer, early toxicities of a randomized clinical trial

    PubMed Central

    2012-01-01

    Background TomoBreast is a unicenter, non-blinded randomized trial comparing conventional radiotherapy (CR) vs. hypofractionated Tomotherapy (TT) for post-operative treatment of breast cancer. The purpose of the trial is to compare whether TT can reduce heart and pulmonary toxicity. We evaluate early toxicities. Methods The trial started inclusion in May 2007 and reached its recruitment in August 2011. Women with stage T1-3N0M0 or T1-2N1M0 breast cancer completely resected by tumorectomy (BCS) or by mastectomy (MA) who consented to participate were randomized, according to a prescribed computer-generated randomization schedule, between control arm of CR 25x2 Gy/5 weeks by tangential fields on breast/chest wall, plus supraclavicular-axillary field if node-positive, and sequential boost 8x2 Gy/2 weeks if BCS (cumulative dose 66 Gy/7 weeks), versus experimental TT arm of 15x2.8 Gy/3 weeks, including nodal areas if node-positive and simultaneous integrated boost of 0.6 Gy if BCS (cumulative dose 51 Gy/3 weeks). Outcomes evaluated were the pulmonary and heart function. Comparison of proportions used one-sided Fisher's exact test. Results By May 2010, 70 patients were randomized and had more than 1 year of follow-up. Out of 69 evaluable cases, 32 were assigned to CR (21 BCS, 11 MA), 37 to TT (20 BCS, 17 MA). Skin toxicity of grade ≥1 at 2 years was 60% in CR, vs. 30% in TT arm. Heart function showed no significant difference for left ventricular ejection fraction at 2 years, CR 4.8% vs. TT 4.6%. Pulmonary function tests at 2 years showed grade ≥1 decline of FEV1 in 21% of CR, vs. 15% of TT and decline of DLco in 29% of CR, vs. 7% of TT (P = 0.05). Conclusions There were no unexpected severe toxicities. Short course radiotherapy of the breast with simultaneous integrated boost over 3 weeks proved feasible without excess toxicities. Pulmonary tests showed a slight trend in favor of Tomotherapy, which will need confirmation with longer

  4. Proposed Modifications to the Conceptual Model of Coaching Efficacy and Additional Validity Evidence for the Coaching Efficacy Scale II-High School Teams

    ERIC Educational Resources Information Center

    Myers, Nicholas; Feltz, Deborah; Chase, Melissa

    2011-01-01

    The purpose of this study was to determine whether theoretically relevant sources of coaching efficacy could predict the measures derived from the Coaching Efficacy Scale II-High School Teams (CES II-HST). Data were collected from head coaches of high school teams in the United States (N = 799). The analytic framework was a multiple-group…

  5. Systematic approach for simultaneously correcting the band-gap andp-dseparation errors of common cation III-V or II-VI binaries in density functional theory calculations within a local density approximation

    DOE PAGESBeta

    Wang, Jianwei; Zhang, Yong; Wang, Lin-Wang

    2015-07-31

    We propose a systematic approach that can empirically correct three major errors typically found in a density functional theory (DFT) calculation within the local density approximation (LDA) simultaneously for a set of common cation binary semiconductors, such as III-V compounds, (Ga or In)X with X = N,P,As,Sb, and II-VI compounds, (Zn or Cd)X, with X = O,S,Se,Te. By correcting (1) the binary band gaps at high-symmetry points , L, X, (2) the separation of p-and d-orbital-derived valence bands, and (3) conduction band effective masses to experimental values and doing so simultaneously for common cation binaries, the resulting DFT-LDA-based quasi-first-principles methodmore » can be used to predict the electronic structure of complex materials involving multiple binaries with comparable accuracy but much less computational cost than a GW level theory. This approach provides an efficient way to evaluate the electronic structures and other material properties of complex systems, much needed for material discovery and design.« less

  6. Combination therapy of angiotensin II receptor blocker and calcium channel blocker exerts pleiotropic therapeutic effects in addition to blood pressure lowering: amlodipine and candesartan trial in Yokohama (ACTY).

    PubMed

    Maeda, Akinobu; Tamura, Kouichi; Kanaoka, Tomohiko; Ohsawa, Masato; Haku, Sona; Azushima, Kengo; Dejima, Toru; Wakui, Hiromichi; Yanagi, Mai; Okano, Yasuko; Fujikawa, Tetsuya; Toya, Yoshiyuki; Mizushima, Shunsaku; Tochikubo, Osamu; Umemura, Satoshi

    2012-01-01

    Recent guidelines recommend combination antihypertensive therapy to achieve the target blood pressure (BP) and to suppress target organ damage. This study aimed to examine the beneficial effects of combination therapy with candesartan and amlodipine on BP control and markers of target organ function in Japanese essential hypertensive patients (N = 20) who did not achieve the target BP level during the monotherapy period with either candesartan or amlodipine. After the monotherapy period, for patients already being treated with amlodipine, a once-daily 8 mg dose of candesartan was added on during the combination therapy period (angiotensin II receptor blocker [ARB] add-on group, N = 10), and a once-daily 5 mg dose of amlodipine was added on for those already being treated with candesartan (calcium channel blocker [CCB] add-on group, N = 10). Combination therapy with candesartan and amlodipine for 12 weeks significantly decreased clinic and home systolic blood pressure (SBP) and diastolic blood pressure (DBP). In addition, the combination therapy was able to significantly reduce urine albumin excretion without decrease in estimated glomerular filtration ratio and resulted in significant improvements in brachial-ankle pulse wave velocity, central SBP, and insulin sensitivity. Furthermore, the CCB add-on group showed a significantly greater decrease in clinic and home DBP than the ARB add-on group. The calcium channel blocker add-on group also exhibited better improvements in vascular functional parameters than the ARB add-on group. These results suggest that combination therapy with candesartan and amlodipine is an efficient therapeutic strategy for hypertension with pleiotropic benefits. PMID:22571446

  7. Easy oxidative addition of the carbon-halogen bond by dimethylplatinum(II) complexes containing a related series of diimine ligands: Synthesis, spectral characterization and crystal structure

    NASA Astrophysics Data System (ADS)

    Momeni, Badri Z.; Fathi, Nastaran; Mohagheghi, Arezoo

    2015-01-01

    Dimethylplatinum(II) complexes [PtMe2(NN)] {NN = 4,4‧-Me2bpy (4,4‧-dimethyl-2,2‧-bipyridine); 5,5‧-Me2bpy (5,5‧-dimethyl-2,2‧-bipyridine)} were reacted with alkyl halides (RX = EtI, EtBr) to yield the organoplatinum(IV) complexes [PtMe2RX(NN)]. On the basis of NMR data, the platinum(IV) product of each reaction contains almost exclusively the trans isomer but small traces of the cis isomers are also observed. On the other hand, the reaction of [PtMe2(NN)] {NN = bu2bpy (4,4‧-di-tert-butyl-2,2‧-bipyridine); 4,4‧-Me2bpy; 5,5‧-Me2bpy} with CH2Br2 gave a mixture of cis and trans-[PtMe2(CH2Br)Br(NN)] formed by the oxidative addition of one of the C-Br bonds. The formation of the cis isomer increases in the order of 5,5‧-Me2bpy > bu2bpy > 4,4‧-Me2bpy. The reaction of [PtMe2(NN)] {NN = bpy (2,2‧-bipyridine), phen (1,10-phenanthroline)} with 1,8-dibromooctane or 1,9-dibromononane afforded the mononuclear complexes [PtMe2{(CH2)nBr}Br(NN)] (n = 8-9). The products were fully characterized by elemental analysis, 1H, 13C, HH COSY, HMQC, DEPT and DEPTQ-135 NMR spectroscopy. The crystal structure of [PtMe2EtI(4,4‧-Me2bpy)] reveals that Pt(IV) atom is six-coordinated in a slightly distorted octahedral geometry with the ethyl group trans to iodide.

  8. Simultaneous quantification of buprenorphine, naloxone and phase I and II metabolites in plasma and breastmilk by liquid chromatography-tandem mass spectrometry.

    PubMed

    Swortwood, Madeleine J; Scheidweiler, Karl B; Barnes, Allan J; Jansson, Lauren M; Huestis, Marilyn A

    2016-05-13

    Opioid abuse during pregnancy is associated with fetal growth restriction, placental abruption, preterm labor, fetal death, and Neonatal Abstinence Syndrome. Current guidelines for medication-assisted opioid addiction treatment during pregnancy are methadone or buprenorphine monotherapy. Buprenorphine/naloxone combination therapy (Suboxone(®)) has not been thoroughly evaluated during pregnancy and insufficient naloxone safety data exist. While methadone- and buprenorphine-treated mothers are encouraged to breastfeed, no studies to date investigated naloxone concentrations during breastfeeding following Suboxone administration. For this reason, we developed and fully validated a liquid chromatography-tandem mass spectrometry method for the simultaneous quantification of buprenorphine, buprenorphine-glucuronide, norbuprenorphine, norbuprenorphine-glucuronide, naloxone, naloxone-glucuronide and naloxone-N-oxide in 100μL human plasma and breastmilk in a single injection following protein precipitation and solid-phase extraction. Lowest limits of quantification were 0.1-2μg/L with 20-100μg/L upper limits of linearity. Bias and imprecision were <±16%. Matrix effects ranged from -57.9 to 11.2 and -84.6 to 29.3% in plasma and breastmilk, respectively. All analytes were stable (within ±20% change from baseline) under all tested conditions (24h room temperature, 72h at 4°C, 3 freeze/thaw cycles at -20°C, and in the autosampler for 72h at 4°C). For proof of concept, buprenorphine and its metabolites were successfully quantified in authentic positive maternal and infant plasma and paired breastmilk specimens. This comprehensive, highly sensitive and specific method detects multiple buprenorphine markers in a small specimen volume. PMID:27083254

  9. Simultaneous determination of hydrazine and phenyl hydrazine using 4′-(4-carboxyphenyl)-2,2′:6′,2″ terpyridine diacetonitrile triphenylphosphine ruthenium(II) tetrafluoroborate complex functionalized multiwalled carbon nanotubes modified electrode

    SciTech Connect

    Tiwari, Ida; Gupta, Mandakini; Sinha, Preeti; Banks, Craig E.

    2014-12-15

    Highlights: • A nanocomposite of ruthenium(II) terpyridine, triphenylphosphine based complex and multiwalled carbon nanotubes have been used first time for simultaneous detection of hydrazine and phenyl hydrazine. • The detection limit reported is lower as compared to other reported works. • The paper also focuses towards effect of ligand variation attached to ruthenium(II) terpyridine based complexes complex for the hydrazine and phenyl hydrazine detection. • Nanocomposite does not involve any biological entity hence high stability. - Abstract: A nanocomposite based on the incorporation of the complex 4′-(4-carboxyphenyl)-2,2′:6′,2″ terpyridine triphenylphosphine diacetonitrile ruthenium(II) tetrafluoroborate with multiwalled carbon nanotubes and ionomer supported upon a glassy carbon electrode substrate is reported and characterized with scanning electron microscopy, transmission electron microscopy and infrared spectroscopy. The electrochemical behavior and stability of the composite electrode was investigated via cyclic voltammetry. The modified electrode exhibits an electro-catalytic activity towards the oxidation of both hydrazine and phenyl hydrazine in 0.1 M phosphate buffer solution (PBS, pH 7.4). The oxidation of hydrazine and phenyl hydrazine occurs at 0.81 V and 0.32 V with limit of detection found to be 3.7 × 10{sup −7} M and 1.15 × 10{sup −7} M and having a linear range from 5 × 10{sup −6} M to 6.5 × 10{sup −3} M, and 5 × 10{sup −6} M to 0.2 × 10{sup −3} M, respectively.

  10. Loss in CD4 T-cell responses to multiple epitopes in influenza due to expression of one additional MHC class II molecule in the host

    PubMed Central

    Nayak, Jennifer L; Sant, Andrea J

    2012-01-01

    An understanding of factors controlling CD4 T-cell immunodominance is needed to pursue CD4 T-cell epitope-driven vaccine design, yet our understanding of this in humans is limited by the complexity of potential MHC class II molecule expression. In the studies described here, we took advantage of genetically restricted, well-defined mouse strains to better understand the effect of increasing MHC class II molecule diversity on the CD4 T-cell repertoire and the resulting anti-influenza immunodominance hierarchy. Interferon-γ ELISPOT assays were implemented to directly quantify CD4 T-cell responses to I-Ab and I-As restricted peptide epitopes following primary influenza virus infection in parental and F1 hybrid strains. We found striking and asymmetric declines in the magnitude of many peptide-specific responses in F1 animals. These declines could not be accounted for by the lower surface density of MHC class II on the cell or by antigen-presenting cells failing to stimulate T cells with lower avidity T-cell receptors. Given the large diversity of MHC class II expressed in humans, these findings have important implications for the rational design of peptide-based vaccines that are based on the premise that CD4 T-cell epitope specificity can be predicted by a simple cataloguing of an individual’s MHC class II genotype. PMID:22747522

  11. Assessment of function and quality of life in a phase II multi-institutional clinical trial of fractionated simultaneous in-field boost radiotherapy for patients with 1-3 metastases.

    PubMed

    Bauman, Glenn; Yartsev, Slav; Roberge, David; MacRae, Robert; Roa, Wilson; Panet-Raymond, Valerie; Masucci, Laura; Yaremko, Brian; D'Souza, David; Palma, David; Sexton, Tracy; Yu, Edward; Pantarotto, Jason R; Ahmad, Belal; Fisher, Barbara; Dar, A Rashid; Lambert, Carole; Pond, Gregory; Stitt, Larry; Tay, Keng Yeow; Rodrigues, George

    2016-07-01

    We examined functional outcomes and quality of life of whole brain radiotherapy (WBRT) with integrated fractionated stereotactic radiotherapy boost (FSRT) for brain metastases treatment. Eighty seven people with 1-3 brain metastases (54/87 lung primary, 42/87 single brain metastases) were enrolled on this Phase II trial of WBRT (30 Gy/10) + simultaneous FSRT, (60 Gy/10). Median overall follow-up and survival was 5.4 months, 6 month actuarial intra-lesional control was 78 %; only 1 patient exhibited grade 4 toxicity (worsened seizures); most treatment related toxicity was grade 1 or 2; 2/87 patients demonstrated asymptomatic radiation necrosis on follow-up imaging. Mean (Min-Max) baseline KPS, Mini Mental Status Exam (MMSE) and FACT-BR quality of life were 83 (70-100), 28 (21-30) and 143 (98-153). Lower baseline MMSE (but not KPS or FACT-Br) was associated with worse survival after adjusting for age, number of metastases, primary and extra-cranial disease status. Crude rates of deterioration (>10 points decrease from baseline for KPS and FACT-Br, MMSE fall to <27) ranged from 26 to 38 % for KPS, 32-59 % for FACT-Br and 0-16 % for MMSE depending on the time-point assessed with higher rates generally noted at earlier time points (≤6 months post-treatment). Using a linear mixed models analysis, significant declines from baseline were noted for KPS and FACT-Br (largest effects at 6 weeks to 3 months) with no significant change in MMSE. The effects on function and quality of life of this integrated treatment of WBRT + simultaneous FSRT were similar to other published series combining WBRT + radiosurgery. PMID:27084705

  12. Addition of Individual Chromosomes of Maize Inbreds B73 and Mo17 to Oat Cultivars Starter and SunII: Maize Chromosome Retention, Transmission, and Plant Phenotype

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Oat-maize addition (OMA) lines with one, or occasionally more, chromosomes of maize (Zea mays L., 2n = 2x = 20) added to an oat (Avena sativa L., 2n = 6x = 42) genomic background can be produced from sexual crosses of oat x maize. Self-fertile disomic addition lines for maize chromosomes 1, 2, 3, 4,...

  13. Gallium(III)- and calcium(II)-catalyzed Meyer-Schuster rearrangements followed by intramolecular aldol condensation or endo-Michael addition.

    PubMed

    Presset, M; Michelet, B; Guillot, R; Bour, C; Bezzenine-Lafollée, S; Gandon, V

    2015-03-28

    The first gallium- and calcium-catalyzed Meyer-Schuster rearrangements are described. Under substrate control, the incipient conjugated ketones can be trapped intramolecularly by β-keto esters or amides to yield cyclic products after aldol condensation or endo-Michael addition. An interesting additive effect that promotes the latter tandem process with calcium has been found. PMID:25503868

  14. Detonation of highly dilute porous explosives; II: Influence of inert additives on the structure of the front, the parameters, and the reaction time

    SciTech Connect

    Shvedov, K.K.; Aniskin, A.I.; Dremin, A.N.; Il'in, A.N.

    1982-06-01

    For the detonation of porous explosives with inert additives, as for the detonation of individual porous explosives, the basic postulates and conclusions of the modern gasdynamic theory of detonation are valid. The influence of solid, refractory inert additives on the decomposition mechanism of porous explosives depends on the individual properties of the explosives and mainly on the dispersity of the additives. With the elimination of pronounced heating of the additives in mixtures with TNT, a certain positive influence on the appearance of decomposition sources and the total reaction time is observed. In cases with hexogen, no such influence is observed, which is evidently the result of physical inhomogeneity of the porous structure of the charge and the sufficiently high detonation pressures of the mixtures. The basic influence of inert additives on the critical diameter, front structure, detonation parameters, and reaction time of porous explosives is exerted through processes of energy absorption in the reaction region and factors leading to energy losses may lead to ambiguity of the detonation conditions in a system with specified chemical potential energy. The state of the additive in the reaction region must be taken into account for reliable theoretical description of the detonation conditions of porous explosives with a large content of inert additives.

  15. Application of a new version of GA-RBF neural network for simultaneous spectrophotometric determination of Zn(II), Fe(II), Co(II) and Cu(II) in real samples: An exploratory study of their complexation abilities toward MTB.

    PubMed

    Rasouli, Zolaikha; Hassanzadeh, Zeinabe; Ghavami, Raouf

    2016-11-01

    The current study for the first time is devoted to the application of whole space genetic algorithm-radial basis function network (wsGA-RBFN) method to determine the content micro minerals of Zn(2+), Fe(2+), Co(2+) and Cu(2+) based on their complexes formation with methylthymol blue (MTB) spectrophotometrically in various pharmaceutical products and vegetable samples. Advantage of wsGA-RBFN compared to GA-RBFN is that centers can be located in any point of the samples spaces. Initially, the parameters controlling behavior of the system were investigated and optimum conditions were selected. Then, an exploratory analysis of complex systems was carried out by chemometrics approaches such as SVD, EFA, MCR-ALS and RAFA. The optimal parameters and conditions for constructing the proposed model of wsGA-RBFN were obtained from processing the data set of synthetic samples. Finally, wsGA-RBFN was successfully applied to the simultaneous determination of Zn(2+), Fe(2+), Co(2+) and Cu(2+) in tomato, white cabbage, red cabbage and lettuce and pharmaceutical products included iron, zinc, multi complete and B12 ampoule. PMID:27591591

  16. Modelling Cu(II) adsorption to ferrihydrite and ferrihydrite-bacteria composites: Deviation from additive adsorption in the composite sorption system

    NASA Astrophysics Data System (ADS)

    Moon, Ellen M.; Peacock, Caroline L.

    2013-03-01

    Bacterially associated iron (hydr)oxides are widespread in natural environments and are potent scavengers of dissolved metal ions. However, it is unclear whether metal sorption on these composites adheres to the additivity principle, and thus whether metal concentrations in environments where these composites comprise a significant proportion of the reactive iron phases can be modelled assuming component additivity. Here we address this issue for Cu adsorption on ferrihydrite-Bacillus subtilis composites. We precipitated pure ferrihydrite and ferrihydrite composites with different ferrihydrite:bacteria mass ratios, and measured Cu adsorption as a function of pH, Cu adsorbed concentration and composite mass ratio. We develop a molecular-level surface complexation model for Cu adsorption on pure ferrihydrite. We then combine our end-member models for Cu adsorption on B. subtilis (Moon and Peacock, 2011) and ferrihydrite to model the observed Cu adsorption on the composites, adopting a component linear additivity approach. By comparing observed Cu adsorption to that predicted by our composite model, constrained to the exact best fitting end-member stability constants, we find that Cu adsorption behaviour on ferrihydrite-B. subtilis composites deviates from additivity. Specifically, Cu adsorption on composites composed mainly of ferrihydrite is enhanced across the adsorption pH edge (pH ˜3-6), while on our composite composed mainly of bacteria adsorption is enhanced at mid-high pH (pH ˜5-6) but diminished at mid-low pH (pH ˜5-3), compared to additivity. In current surface complexation modelling constructs, Cu adsorption on composites composed mainly of ferrihydrite can be modelled in a component additivity approach, by optimising the stability constants for Cu adsorption on the ferrihydrite and bacteria fractions to values that are within the uncertainty on the end-member stability constant values. The deviation from additivity of these composites, apparent when

  17. Acquisition, Renovation, and Construction of an Addition to a Building to Serve as a Sheltered Workshop for Handicapped Adults. Maxi II Practicum.

    ERIC Educational Resources Information Center

    Zoino, John E.

    Presented is the final report of a project to acquire, renovate, and construct a building addition to house a sheltered workshop and provide instruction in basic life skills, social skills, simple production work skills, and life oriented academics for moderately retarded adults. Sections are provided on the following aspects of the project…

  18. The role of additives in moderating the influence of Fe(III) and Cu(II) on the radiochemical yield of [⁶⁸Ga(DOTATATE)].

    PubMed

    Oehlke, Elisabeth; Lengkeek, Nigel A; Le, Van So; Pellegrini, Paul A; Greguric, Ivan; Weiner, Ron

    2016-01-01

    [(68)Ga(DOTATATE)] has demonstrated its clinical usefulness. Both Fe(3+) and Cu(2+), potential contaminants in Gallium-68 generator eluent, substantially reduce the radiochemical (RC) yield of [(68)Ga(DOTATATE)] if the metal/ligand ratio of 1:1 is exceeded. A variety of compounds were examined for their potential ability to reduce this effect. Most had no effect on RC yield. However, addition of phosphate diminished the influence of Fe(3+) by likely forming an insoluble iron salt. Addition of ascorbic acid reduced Cu(2+) and Fe(3+) to Cu(+) and Fe(2+) respectively, both of which have limited impact on RC yields. At low ligand amounts (5 nmol DOTATATE), the addition of 30 nmol phosphate (0.19 mM) increased the tolerance of Fe(3+) from 4 nmol to 10 nmol (0.06 mM), while the addition of ascorbic acid allowed high RC yields (>95%) in the presence of 40 nmol Fe(3+) (0.25 mM) and 100 nmol Cu(2+) (0.63 mM). The effect of ascorbic acid was highly pH-dependant, and gave optimal results at pH 3. PMID:26405839

  19. Irreversible Wash Aid Additive for Cesium Mitigation: Phase II. Selection and/or Modification of COTS Field Portable Waste Water Systems

    SciTech Connect

    Kaminski, Michael; Mertz, Carol; Kivenas, Nadia; Magnuson, Matthew

    2015-01-01

    After an accidental or malicious release of radioactivity, large urban areas may be contaminated, compromising response efforts by first responders and law enforcement officials. In addition, some public services (e.g., drinking water and wastewater treatment, electrical power distribution, etc.) may be disrupted. In such an event, it may be important to deploy mitigation efforts in certain areas to restore response activities and public services (Fig. S-1). This report explores the state-of-the-art approach for a system to rapidly return critical infrastructure components to service following a cesium-137 (Cs-137) radiological dispersal device (RDD) release while avoiding the spread of Cs-137 beyond its original deposition area and minimizing the amount of Cs-137-contaminated wastewater. Specifically, we describe a wash system consisting of chemical additives added to fire hydrant water and irreversible solid sequestering agents added as the water is collected and treated for recycle in situ. The wash system is intended to be a rapidly deployable, cost-effective means of mitigating an urban setting for the purpose of restoring critical infrastructure and operational activities after a radiological release.

  20. Ru(II)-Catalyzed C-H Activation: Amide-Directed 1,4-Addition of the Ortho C-H Bond to Maleimides.

    PubMed

    Keshri, Puspam; Bettadapur, Kiran R; Lanke, Veeranjaneyulu; Prabhu, Kandikere Ramaiah

    2016-07-15

    Maleimide has been used as a selective coupling partner to generate conjugate addition products exclusively. The typical Heck-type oxidative coupling that occurs when alkenes are used is avoided by choosing maleimide as an alkene, which cannot undergo β-hydride elimination due to the unavailability of a syn-periplanar β-hydrogen atom. The amide nitrogen, which is notorious for undergoing tandem reactions to generate spirocyclic or annulation products under cross-coupling conditions, remains innocent in this report. Along with the substrate scope, a robustness screen has been performed to analyze the performance of amide as a directing group in the presence of other directing groups and also to examine the tolerance of the reaction conditions for other frequently encountered functional groups. PMID:27314834

  1. Reducing Dangerous Effects of Unsymmetrical Dimethyl Hydrazine as a Liquid Propellant by Addition of Hydroxyethylhydrazine, Part II, Performance with Several Oxidizers

    NASA Astrophysics Data System (ADS)

    Keshavarz, Mohammad Hossein; Ramadan, Alireza; Mousaviazar, Ali; Zali, Abbas; Shokrollahi, Arash

    2011-07-01

    This work continues the study of suitable binary liquid mixtures of unsymmetrical dimethylhydrazine (UDMH) and hydroxyethylhydrazine (HEH) to reduce the harmful effects of pure UDMH. The synthesized HEH was mixed with UDMH up to 40 wt% of HEH to study the performance and properties of binary liquid mixtures of UDMH/HEH. The existence of strong hydrogen bonding between HEH and UDMH provides low-volatile mixtures of these hydrazine derivatives. The addition of HEH significantly reduces the vapor pressure of UDMH, thus reducing the known UDMH health risk to inhalation exposure. Specific impulse was used to study performance of binary mixture UDMH/HEH with respect to pure UDMH. A binary mixture of UDMH/HEH reacts spontaneously in contact with nitrogen tetroxide, red fuming nitric acid (RFNA), and inhibited red fuming nitric acid (IRFNA).

  2. Complete reversal of muscle wasting in experimental cancer cachexia: Additive effects of activin type II receptor inhibition and β-2 agonist.

    PubMed

    Toledo, Míriam; Busquets, Sílvia; Penna, Fabio; Zhou, Xiaolan; Marmonti, Enrica; Betancourt, Angelica; Massa, David; López-Soriano, Francisco J; Han, H Q; Argilés, Josep M

    2016-04-15

    Formoterol is a highly potent β2-adrenoceptor-selective agonist, which is a muscle growth promoter in many animal species. Myostatin/activin inhibition reverses skeletal muscle loss and prolongs survival of tumor-bearing animals. The aim of this investigation was to evaluate the effects of a combination of the soluble myostatin receptor ActRIIB (sActRIIB) and the β2-agonist formoterol in the cachectic Lewis lung carcinoma model. The combination of formoterol and sActRIIB was extremely effective in reversing muscle wasting associated with experimental cancer cachexia in mice. Muscle weights from tumor-bearing animals were completely recovered following treatment and this was also reflected in the measured grip strength. This combination increased food intake in both control and tumor-bearing animals. The double treatment also prolonged survival significantly without affecting the weight and growth of the primary tumor. In addition, it significantly reduced the number of metastasis. Concerning the mechanisms for the preservation of muscle mass during cachexia, the effects of formoterol and sActRIIB seemed to be additive, since formoterol reduced the rate of protein degradation (as measured in vitro as tyrosine release, using incubated isolated individual muscles) while sActRIIB only affected protein synthesis (as measured in vivo using tritiated phenylalanine). Formoterol also increased the rate of protein synthesis and this seemed to be favored by the presence of sActRIIB. Combining formoterol and sActRIIB seemed to be a very promising treatment for experimental cancer cachexia. Further studies in human patients are necessary and may lead to a highly effective treatment option for muscle wasting associated with cancer. PMID:26595367

  3. Phase I-II study of hypofractionated simultaneous integrated boost using volumetric modulated arc therapy for adjuvant radiation therapy in breast cancer patients: a report of feasibility and early toxicity results in the first 50 treatments

    PubMed Central

    2012-01-01

    Background To report results in terms of feasibility and early toxicity of hypofractionated simultaneous integrated boost (SIB) approach with Volumetric Modulated Arc Therapy (VMAT) as adjuvant treatment after breast-conserving surgery. Methods Between September 2010 and May 2011, 50 consecutive patients presenting early-stage breast cancer were submitted to adjuvant radiotherapy with SIB-VMAT approach using RapidArc in our Institution (Istituto Clinico Humanitas ICH). Three out of 50 patients were irradiated bilaterally (53 tumours in 50 patients). All patients were enrolled in a phase I-II trial approved by the ICH ethical committee. All 50 patients enrolled in the study underwent VMAT-SIB technique to irradiate the whole breast with concomitant boost irradiation of the tumor bed. Doses to whole breast and surgical bed were 40.5 Gy and 48 Gy respectively, delivered in 15 fractions over 3 weeks. Skin toxicities were recorded during and after treatment according to RTOG acute radiation morbidity scoring criteria with a median follow-up of 12 months (range 8–16). Cosmetic outcomes were assessed as excellent/good or fair/poor. Results The median age of the population was 68 years (range 36–88). According to AJCC staging system, 38 breast lesions were classified as pT1, and 15 as pT2; 49 cases were assessed as N0 and 4 as N1. The maximum acute skin toxicity by the end of treatment was Grade 0 in 20/50 patients, Grade 1 in 32/50, Grade 2 in 0 and Grade 3 in 1/50 (one of the 3 cases of bilateral breast irradiation). No Grade 4 toxicities were observed. All Grade 1 toxicities had resolved within 3 weeks. No significant differences in cosmetic scores on baseline assessment vs. 3 months and 6 months after the treatment were observed: all patients were scored as excellent/good (50/50) compared with baseline; no fair/poor judgment was recorded. No other toxicities or local failures were recorded during follow-up. Conclusions The 3-week course of

  4. Food additives

    MedlinePlus

    Food additives are substances that become part of a food product when they are added during the processing or making of that food. "Direct" food additives are often added during processing to: Add nutrients ...

  5. Oxidative addition of allylic halides to ruthenium(II) compounds. Preparation, reactions, and X-ray crystallographic structure of ruthenium(IV)-allyl complexes

    SciTech Connect

    Nagashima, Hideo; Mukai, Katsunori; Shiota, Yusuke; Yamaguchi, Keitaro; Ara, Kenichi; Fukahori, Takahiko; Itoh, Kenji ); Suzuki, Hiroharu; Akita, Munetaka; Moro-oka, Yoshihiko )

    1990-03-01

    The oxidative addition of allylic halides to (C{sub 5}R{sub 5})RuL{sub 2}X (R = H, Me; L = CO, PPh{sub 3}) gave new Ru(IV)-{eta}{sup 3}-allyl complexes, (C{sub 5}R{sub 5})RuX{sub 2}({eta}{sup 3}-allyl). An X-ray structure determination was carried out on (C{sub 5}Me{sub 5})RuBr{sub 2}({eta}{sup 3}-C{sub 3}H{sub 5}), indicating a pseudo-piano-stool structure having two Br atoms and two terminal carbons of the endo-{eta}{sup 3}-allyl ligand located at the basal positions. There is a crystal mirror plane bisecting the pentamethylcyclopentadienyl and the {pi}-allyl ligands. Crystal data: orthorhombic, space group P2{sub 1}2{sub 1}2{sub 1}, a = 22.738 (1) {angstrom}, b = 13.367 (7) {angstrom}, c = 9.383 (1) {angstrom}, Z = 4., data refined to R = 0.0695. Its {sup 1}H and {sup 13}C NMR spectra showed symmetric allyl signals, supporting that the above-described piano-stool structure is maintained even in solution.

  6. Improvement of Resistance to Slag Penetration in Magnesia-Based Refractory with Colloidal Alumina Addition II by Means of a Proper Particle Size Distribution of MgO

    NASA Astrophysics Data System (ADS)

    Wang, Huijun; Sichen, Du

    2016-06-01

    By addition of colloidal alumina, three different particle sizes of dead burnt MgO were employed as raw materials to prepare MgO-based spinel substrates at 1773 K (1500 °C). It was found that the particle size of MgO, as well as its size distribution, had substantial impact on the resistance of the refractory to the slag penetration at 1873 K (1600 °C). Using relatively small particles of MgO (<0.5 mm) can efficiently limit the slag penetration, due to the formation of solid phases (CaO·Al2O3 and CaO-MgO-Al2O3) at the grain boundaries. A particularly significant improvement against the slag penetration was found on MgO substrates with a proper particle size distribution in a size range of 0-1 mm. The improvement could be mainly related to the higher density and distribution of spinel phase in the MgO matrix, which is mostly located at the borders of large MgO particles.

  7. Food additives

    PubMed Central

    Spencer, Michael

    1974-01-01

    Food additives are discussed from the food technology point of view. The reasons for their use are summarized: (1) to protect food from chemical and microbiological attack; (2) to even out seasonal supplies; (3) to improve their eating quality; (4) to improve their nutritional value. The various types of food additives are considered, e.g. colours, flavours, emulsifiers, bread and flour additives, preservatives, and nutritional additives. The paper concludes with consideration of those circumstances in which the use of additives is (a) justified and (b) unjustified. PMID:4467857

  8. Theoretical and kinetic study of the reaction of ethyl methyl ketone with HO2 for T = 600-1600 K. Part II: addition reaction channels.

    PubMed

    Zhou, Chong-Wen; Mendes, Jorge; Curran, Henry J

    2013-06-01

    The temperature and pressure dependence of the addition reaction of ethyl methyl ketone (EMK) with HO2 radical has been calculated using the master equation method employing conventional transition state theory estimates for the microcanonical rate coefficients in the temperature range of 600-1600 K. Geometries, frequencies, and hindrance potentials were obtained at the B3LYP/6-311G(d,p) level of theory. A modified G3(MP2,CC) method has been used to calculate accurate electronic energies for all of the species involved in the reactions. The rigid-rotor harmonic oscillator approximation has been used for all of the vibrations except for the torsional degrees of freedom which are being treated as 1D hindered rotors. Asymmetric Eckart barriers were used to model tunneling effect in a one-dimensional reaction coordinate through saddle points. Our calculated results show that the four reaction channels forming 1-buten-2-ol + HO2 radical (R5), 2-buten-2-ol + HO2 radical (R10), acetic acid + ethylene + OH radical (R13), and 2-methyl-2-oxetanol + OH radical (R15) are the dominant channels. When the temperature is below 1000 K, the reaction R15 forming the cyclic ether, 2-methyl-2-oxetanol, is dominant while the reaction R13 forming acetic acid + ethylene + OH radical becomes increasingly dominant at temperatures above 1000 K. The other two channels forming 1-buten-2-ol, 2-buten-2-ol, and HO2 radical are not dominant but are still important product channels over the whole temperature range investigated here. No pressure dependence has been found for the reaction channels forming 2-methyl-2-oxetanol + OH radical and acetic acid + ethylene + OH radical. A slightly negative pressure dependence has been found for the reaction channels producing the two butenols. Rate constants for the four important reaction channels at 1 atm (in cm(3) mol(-1) s(-1)) are k(R5) = 2.67 × 10(15) × T(-1.32)exp(-16637/T), k(R10) = 1.62 × 10(8) × T(0.57)exp(-13142/T), k(R13) = 2.29 × 10(17) × T

  9. Feasibility, tolerability, and efficacy of the concurrent addition of erlotinib to thoracic radiotherapy in locally advanced unresectable non-small-cell lung cancer: a Phase II trial

    PubMed Central

    Martínez, Enrique; Martínez, Maite; Rico, Mikel; Hernández, Berta; Casas, Francesc; Viñolas, Nuria; Pérez-Casas, Ana; Dómine, Manuel; Mínguez, Julián

    2016-01-01

    Purpose Although many studies have confirmed the synergic effects of combining chemotherapy (CT) and radiotherapy (RT), clinical data evaluating safety and efficacy of erlotinib in combination with RT in locally advanced non-small-cell lung cancer (NSCLC) are limited. The aim of this study was to determine the feasibility, tolerability, and efficacy of the concurrent addition of erlotinib to the standard three-dimensional conformal thoracic RT in patients with unresectable or locally advanced NSCLC who are not candidates for receiving standard CT. Patients and methods Feasibility and tolerability, assessed by evaluating adverse events (AEs), and effectiveness, by calculating progression-free survival (PFS), overall survival (OS), cancer-specific survival (CSS), and objective response rate (ORR), were analyzed in 30 patients receiving RT alone and 60 receiving RT and erlotinib. Results Erlotinib with RT showed an extended CSS and a higher rate of complete responses compared with RT alone. No differences between groups were found regarding OS, PFS, and ORR. AEs were significantly higher in the combined treatment, which mainly included cutaneous toxicity, dyspnea, fatigue, hyporexia, diarrhea, and infection. Erlotinib did not increase the toxicity produced by RT. Conclusion The combination of erlotinib with RT produced, in our study, a scarce clinical benefit in the treatment of unresectable or locally advanced NSCLC, limited to complete responses and longer CSS rate compared with RT alone. Increased toxicity events were associated with combined therapy, which mainly included cutaneous toxicity. In our opinion, further studies in molecularly unselected lung cancer patients treated with EGFR TKIs and RT are not indicated. The use of biomarkers for the identification of patients that are most likely to benefit from this treatment is an essential next step in the research of this condition. PMID:27042098

  10. An Automated Software Package for the KISS Objective-Prism Survey for Emission-Line Galaxies. II. Recent Additions and Project Status

    NASA Astrophysics Data System (ADS)

    Frattare, L. M.; Salzer, J. J.

    1996-05-01

    We present an update on the KPNO International Spectroscopic Survey (KISS) project. KISS is a wide-field survey for extragalactic emission-line objects being carried out with the Burrell Schmidt at Kitt Peak. While we are utilizing the classical objective-prism technique to find strong-lined star-forming galaxies and AGNs, the use of CCD detectors and automated reduction software promise to make KISS a powerful tool for the study of activity in galaxies. We are currently completing our first survey strip (100 square degrees). The data consist of deep (to B = 20) objective-prism images, deep direct images in both B and V, and small-format photometric calibration images of each field. The KISS reduction package was designed to run under the IRAF image processing environment, and will eventually grow to be a complete IRAF package. Tasks added to the package over the past year include precise astrometry and photometry modules. The astrometry routines utilize the HST Guide Star Catalog to perform a full plate solution on the direct image of each Schmidt field, and then assign accurate equatorial coordinates to each object in the field. The photometry module performs aperture photometry on the direct images for all objects in the KISS database catalog, and provides routines to transfer the photometry calibration from the small-format images taken under photometric conditions to the large-format survey images. Extensive tests and modifications have also been carried out on the pre-existing software described by Herrero & Salzer (1995) in order to better fine-tune the reduction procedures and parameter settings. In addition to presenting a complete description of the new software, we describe the current status of the survey and present some preliminary characteristics of the sample. Other members of the KISS project include V. Lipovetsky & A. Kniazev (S.A.O.), T. Boroson (NOAO/USGP), T. Thuan (U. Virginia), J. Moody (BYU), Y. Izotov (Ukrainian Acad. Sci.), and J. Herrero

  11. Additive effects of cilnidipine, an L-/N-type calcium channel blocker, and an angiotensin II receptor blocker on reducing cardiorenal damage in Otsuka Long-Evans Tokushima Fatty rats with type 2 diabetes mellitus.

    PubMed

    Mori, Yutaka; Aritomi, Shizuka; Niinuma, Kazumi; Nakamura, Tarou; Matsuura, Kenichi; Yokoyama, Junichi; Utsunomiya, Kazunori

    2014-01-01

    Cilnidipine (Cil), which is an L-/N-type calcium channel blocker (CCB), has been known to provide renal protection by decreasing the activity of the sympathetic nervous system (SNS) and the renin-angiotensin system. In this study, we compared the effects of the combination of Cil and amlodipine (Aml), which is an L-type CCB, with an angiotensin (Ang) II receptor blocker on diabetic cardiorenal damage in spontaneously type 2 diabetic rats. Seventeen-week-old Otsuka Long-Evans Tokushima Fatty rats were randomly assigned to receive Cil, Aml, valsartan (Val), Cil + Val, Aml + Val, or a vehicle (eight rats per group) for 22 weeks. Antihypertensive potencies were nearly equal among the CCB monotherapy groups and the combination therapy groups. The lowering of blood pressure by either treatment did not significantly affect the glycemic variables. However, exacerbations of renal and heart failure were significantly suppressed in rats administered Cil or Val, and additional suppression was observed in those administered Cil + Val. Although Val increased the renin-Ang system, Aml + Val treatment resulted in additional increases in these parameters, while Cil + Val did not show such effects. Furthermore, Cil increased the ratio of Ang-(1-7) to Ang-I, despite the fact that Val and Aml + Val decreased the Ang-(1-7) levels. These actions of Cil + Val might be due to their synergistic inhibitory effect on the activity of the SNS, and on aldosterone secretion through N-type calcium channel antagonism and Ang II receptor type 1 antagonism. Thus, Cil may inhibit the progression of cardiorenal disease in type 2 diabetes patients by acting as an N-type CCB and inhibiting the aldosterone secretion and SNS activation when these drugs were administered in combination with an Ang II receptor blocker. PMID:24970998

  12. Phase II Study of the Addition of Bevacizumab to Standard Chemoradiation for Loco-regionally Advanced Nasopharyngeal Carcinoma: Radiation Therapy Oncology Group (RTOG) Trial 0615

    PubMed Central

    Lee, Nancy Y.; Zhang, Ed; Pfister, David. G.; Kim, John; Garden, Adam. S.; Mechalakos, James; Hu, Kenneth; Le, Quynh T.; Colevas, A. Dimitrios; Glisson, Bonnie S.; Chan, Anthony T.C.; Ang, K. Kian

    2016-01-01

    Purpose We sought to improve the outcomes for loco-regionally advanced nasopharyngeal carcinoma (NPC) by testing the feasibility/safety of adding bevacizumab to chemoradiation. Patients/Methods Eligible patients with ≥T2b and/or positive node(s) were prescribed 3 cycles of bevacizumab (15 mg/kg) and cisplatin (100 mg/m2) both given on days 1, 22, and 43 of radiation (70 Gy) using IMRT delivered over 33 days on a daily basis, Monday through Friday. This is followed by 3 cycles of bevacizumab (15 mg/kg), cisplatin (80 mg/m2) both were given on days 64, 85, and 106 and fluorouracil (1000 mg/m2/d) on days 64–67, 85–88, 106–109 after radiation. The primary endpoint was to evaluate the safety of the addition of bevacizumab to chemoradiation, specifically looking at treatment-related Grade 4 hemorrhage and/or any Grade 5 adverse event in the first year. Toxicity during and after treatment were collected along with tumor control endpoints. The analysis was done per protocol. This protocol has completed its target accrual. Results There were a total of 46 patients enrolled in this study of whom 44 patients were eligible for analysis. No grade 3–4 hemorrhage or grade 5 adverse events were observed; 9 patients (20.5%) experienced grade 1–2 hemorrhage. Grade 4 adverse events were experienced by the following numbers of patients: leukopenia NOS – 6; lymphopenia – 5; neutrophil count – 5; pharyngolaryngeal pain – 2; hemoglobin – 1; infection with grade 3–4 neutrophils (blood) – 1; infection with grade 3–4 neutrophils [skin (cellulitis)] – 1; tinnitus – 1; thrombosis – 1; radiation mucositis – 1. The most common grade 3 adverse events were radiation mucositis – 33; dysphagia – 25; and mucositis/stomatitis (clinical exam) (pharynx) – 15. Two patients experienced late grade 3 xerostomia. Other late grade 3 adverse events were: dysphagia – 5; hearing impaired – 3; neuralgia NOS – 2; constitutional symptoms (other) – 1; dehydration

  13. Solar Type II Radio Bursts and IP Type II Events

    NASA Technical Reports Server (NTRS)

    Cane, H. V.; Erickson, W. C.

    2005-01-01

    We have examined radio data from the WAVES experiment on the Wind spacecraft in conjunction with ground-based data in order to investigate the relationship between the shocks responsible for metric type II radio bursts and the shocks in front of coronal mass ejections (CMEs). The bow shocks of fast, large CMEs are strong interplanetary (IP) shocks, and the associated radio emissions often consist of single broad bands starting below approx. 4 MHz; such emissions were previously called IP type II events. In contrast, metric type II bursts are usually narrowbanded and display two harmonically related bands. In addition to displaying complete dynamic spectra for a number of events, we also analyze the 135 WAVES 1 - 14 MHz slow-drift time periods in 2001-2003. We find that most of the periods contain multiple phenomena, which we divide into three groups: metric type II extensions, IP type II events, and blobs and bands. About half of the WAVES listings include probable extensions of metric type II radio bursts, but in more than half of these events, there were also other slow-drift features. In the 3 yr study period, there were 31 IP type II events; these were associated with the very fastest CMEs. The most common form of activity in the WAVES events, blobs and bands in the frequency range between 1 and 8 MHz, fall below an envelope consistent with the early signatures of an IP type II event. However, most of this activity lasts only a few tens of minutes, whereas IP type II events last for many hours. In this study we find many examples in the radio data of two shock-like phenomena with different characteristics that occur simultaneously in the metric and decametric/hectometric bands, and no clear example of a metric type II burst that extends continuously down in frequency to become an IP type II event. The simplest interpretation is that metric type II bursts, unlike IP type II events, are not caused by shocks driven in front of CMEs.

  14. Food additives.

    PubMed

    Berglund, F

    1978-01-01

    The use of additives to food fulfils many purposes, as shown by the index issued by the Codex Committee on Food Additives: Acids, bases and salts; Preservatives, Antioxidants and antioxidant synergists; Anticaking agents; Colours; Emulfifiers; Thickening agents; Flour-treatment agents; Extraction solvents; Carrier solvents; Flavours (synthetic); Flavour enhancers; Non-nutritive sweeteners; Processing aids; Enzyme preparations. Many additives occur naturally in foods, but this does not exclude toxicity at higher levels. Some food additives are nutrients, or even essential nutritents, e.g. NaCl. Examples are known of food additives causing toxicity in man even when used according to regulations, e.g. cobalt in beer. In other instances, poisoning has been due to carry-over, e.g. by nitrate in cheese whey - when used for artificial feed for infants. Poisonings also occur as the result of the permitted substance being added at too high levels, by accident or carelessness, e.g. nitrite in fish. Finally, there are examples of hypersensitivity to food additives, e.g. to tartrazine and other food colours. The toxicological evaluation, based on animal feeding studies, may be complicated by impurities, e.g. orthotoluene-sulfonamide in saccharin; by transformation or disappearance of the additive in food processing in storage, e.g. bisulfite in raisins; by reaction products with food constituents, e.g. formation of ethylurethane from diethyl pyrocarbonate; by metabolic transformation products, e.g. formation in the gut of cyclohexylamine from cyclamate. Metabolic end products may differ in experimental animals and in man: guanylic acid and inosinic acid are metabolized to allantoin in the rat but to uric acid in man. The magnitude of the safety margin in man of the Acceptable Daily Intake (ADI) is not identical to the "safety factor" used when calculating the ADI. The symptoms of Chinese Restaurant Syndrome, although not hazardous, furthermore illustrate that the whole ADI

  15. Direct catalytic oxyamination of benzene to aniline over Cu(II) nanoclusters supported on CuCr2O4 spinel nanoparticles via simultaneous activation of C-H and N-H bonds.

    PubMed

    Acharyya, Shankha S; Ghosh, Shilpi; Bal, Rajaram

    2014-11-11

    We report the facile synthesis of a highly efficient, reusable catalyst comprising Cu(II) nanoclusters supported on CuCr2O4 spinel nanoparticles for the oxyamination of benzene to aniline (H2O2 + NH3) under mild aqueous reaction conditions. The synergy between the Cu(II) nanoclusters and CuCr2O4 spinel nanoparticles plays the most vital role towards its high catalytic activity. PMID:24990186

  16. Aromatic C-nitrosation by a copper(II)-nitrosyl complex.

    PubMed

    Rout, Kanhu Charan; Mondal, Biplab

    2015-01-28

    Copper(II) complex of 4-amino-3-hydroxy-1-sulphonic acid was synthesized and characterized. Upon addition of nitric oxide, the copper(II) center of the complex in methanol was found to undergo reduction through an unstable copper(II)-nitrosyl intermediate. The formation of the intermediate was confirmed by UV-visible and FT-IR spectroscopy. The reduction of the copper(II) center was accompanied with a simultaneous C-nitrosation of the aromatic ring of the ligand. The C-nitrosation product was isolated and characterized by various spectroscopic analyses. PMID:25476484

  17. Phosphazene additives

    SciTech Connect

    Harrup, Mason K; Rollins, Harry W

    2013-11-26

    An additive comprising a phosphazene compound that has at least two reactive functional groups and at least one capping functional group bonded to phosphorus atoms of the phosphazene compound. One of the at least two reactive functional groups is configured to react with cellulose and the other of the at least two reactive functional groups is configured to react with a resin, such as an amine resin of a polycarboxylic acid resin. The at least one capping functional group is selected from the group consisting of a short chain ether group, an alkoxy group, or an aryloxy group. Also disclosed are an additive-resin admixture, a method of treating a wood product, and a wood product.

  18. Potlining Additives

    SciTech Connect

    Rudolf Keller

    2004-08-10

    In this project, a concept to improve the performance of aluminum production cells by introducing potlining additives was examined and tested. Boron oxide was added to cathode blocks, and titanium was dissolved in the metal pool; this resulted in the formation of titanium diboride and caused the molten aluminum to wet the carbonaceous cathode surface. Such wetting reportedly leads to operational improvements and extended cell life. In addition, boron oxide suppresses cyanide formation. This final report presents and discusses the results of this project. Substantial economic benefits for the practical implementation of the technology are projected, especially for modern cells with graphitized blocks. For example, with an energy savings of about 5% and an increase in pot life from 1500 to 2500 days, a cost savings of $ 0.023 per pound of aluminum produced is projected for a 200 kA pot.

  19. Type II universal spacetimes

    NASA Astrophysics Data System (ADS)

    Hervik, S.; Málek, T.; Pravda, V.; Pravdová, A.

    2015-12-01

    We study type II universal metrics of the Lorentzian signature. These metrics simultaneously solve vacuum field equations of all theories of gravitation with the Lagrangian being a polynomial curvature invariant constructed from the metric, the Riemann tensor and its covariant derivatives of an arbitrary order. We provide examples of type II universal metrics for all composite number dimensions. On the other hand, we have no examples for prime number dimensions and we prove the non-existence of type II universal spacetimes in five dimensions. We also present type II vacuum solutions of selected classes of gravitational theories, such as Lovelock, quadratic and L({{Riemann}}) gravities.

  20. Determination of Free Acid by Standard Addition with Potassium Thiocyanate as Complexant

    SciTech Connect

    Baumann, E.W.

    2001-05-29

    A method is described for determination of free acid in solutions containing the hydrolyzable ions Al (III), Cr(III), Fe(III), Hg(II), Ni(II), Th(IV), and U(VI). The concentration of the sample is calculated either by solving three simultaneous Nernst equations, by the Gran plot procedure, or by means of a microprocessor pH meter. Molar concentrations of metal ion up to 2.5 times that of the acid can be tolerated. The method has been applied to analysis of nuclear processing solutions that contain Pu(III), in addition to the ions listed above.

  1. Simultaneity, relativity and conventionality

    NASA Astrophysics Data System (ADS)

    Janis, Allen I.

    2008-01-01

    The view of simultaneity presented by Max Jammer is almost breathtaking, encompassing, as the book's subtitle suggests, the period from antiquity to the 21st century. Many interesting things are to be found along the way. For example, what Jammer (p. 49) says "may well be regarded as probably the earliest recorded example of an operational definition of distant simultaneity" is due to St. Augustine (in his Confessions, written in 397 A.D.; for a modern translation, see Augustine, 2006). He was arguing against astrology by presenting the story of two women, one rich and one poor, who gave birth simultaneously. Although the two children thus had precisely the same horoscopes, their lives followed quite different courses. And how was it determined that the births were simultaneous? A messenger went from each birth site to the other, leaving the instant the child was born (and, presumably, traveling with equal speeds). Since the messengers met at the midpoint between the locations of the two births, the births must have been simultaneous. This is, of course, quite analogous to Albert Einstein's definition of simultaneity (given more than 1500 years later), which will be discussed in Section 2.1.

  2. Phase II Study Evaluating the Addition of Cetuximab to the Concurrent Delivery of Weekly Carboplatin, Paclitaxel, and Daily Radiotherapy for Patients With Locally Advanced Squamous Cell Carcinomas of the Head and Neck

    SciTech Connect

    Suntharalingam, Mohan; Kwok, Young; Goloubeva, Olga; Parekh, Arti; Taylor, Rodney; Wolf, Jeffrey; Zimrin, Ann; Strome, Scott; Ord, Robert; Cullen, Kevin J.

    2012-04-01

    Purpose: To report the mature data of a prospective Phase II trial designed to evaluate the efficacy of an epidermal growth factor receptor inhibitor cetuximab (CTX) added to the concurrent therapy of weekly paclitaxel/carboplatin (PC) and daily radiation therapy (RT). Methods and Materials: From 2005 to 2009, a total of 43 patients were enrolled in the study. The median follow-up was 31 months (range, 9-59 months). All patients had Stage III/IV disease at presentation, and 67% had oropharyngeal primaries. The weekly IV dose schedules were CTX 250 mg/m{sup 2} (400 mg/m{sup 2} IV loading dose 1 week before RT), paclitaxel 40 mg/m{sup 2}, and carboplatin AUC 2. RT was given at 1.8 Gy per day to 70.2 Gy. Intensity-modulated RTwas used in 70% of cases. Results: All patients completed the planned RT dose, 74% without any treatment breaks. The planned CTX and PC cycles were completed in 70% (91% with at least seven of planned nine cycles) and 56% (93% with at least seven of planned eight cycles) of patients, respectively. Toxicity included Grade 3 mucositis (79%), rash (9%), leucopenia (19%), neutropenia (19%), and RT dermatitis (16%). The complete response (CR) rate at the completion of therapy was 84%. The estimated 3-year local regional control rate was 72%. Six patients with an initial CR subsequently experienced a local recurrence, 10 patients experienced distant progression. The median overall survival and disease-free survivals have not been reached. The 3-year actuarial overall survival and disease-free survival were 59% and 58%, respectively. Conclusions: The addition of CTX to weekly PC and daily RT was well tolerated and resulted in encouraging local control and survival rates.

  3. Evaluating Simultaneous Integrals

    ERIC Educational Resources Information Center

    Kwong, Harris

    2012-01-01

    Many integrals require two successive applications of integration by parts. During the process, another integral of similar type is often invoked. We propose a method which can integrate these two integrals simultaneously. All we need is to solve a linear system of equations.

  4. Orchestrating Simultaneous Renewal.

    ERIC Educational Resources Information Center

    Theobald, Paul; Rochon, Ronald

    1999-01-01

    Orchestrating simultaneous renewal of schools and teacher education is possible in the presence of appropriate leadership, reformer diversity, program audits, accurate assessments, and a focus on the big picture. Public education is the glue that holds society together, not just a place where job skills are acquired. (MLH)

  5. Determination of chlorinated pesticide residues in foods. II. Simultaneous analysis of chlorinated pesticide and phthalate ester residues by using AgNO3-coated Florisil column chromatography for cleanup of various samples.

    PubMed

    Suzuki, T; Ishikawa, K; Sato, N; Sakai, K I

    1979-05-01

    A simplified method suitable for simultaneous analysis of chlorinated pesticide and phthalate ester residues in various foods was developed. Chemical residues were quantitatively extracted from fatty and vegetable samples with acetonitrile as follows: Chemical standard in 0.5 mL ethanol solution was added to 10 g homogenized sample. After 3 hr, pork and beef were extracted 3 times with 20 mL portions of acetonitrile. The acetonitrile layers were diluted with water and extracted with n-hexane. Rice samples were combined with 10 mL water, 5 mL acetonitrile and 1 mL ethanol and extracted 3 times with 20 mL portions of n-hexane. The n-hexane concentrate from each sample was submitted to AgNO3-coated Florisil column chromatography. The AgNO3 coating adequately adsorbed interfering coextractives. Extracts of fish and vegetable samples were separated into 2 fractions by the above column chromatography. Supplemental cleanup procedures were also developed to accurately determine phthalate esters eluted in the second fraction. Satisfactory gas chromatograms were obtained for most samples. PMID:479097

  6. Systematic approach for simultaneously correcting the band-gap andp-dseparation errors of common cation III-V or II-VI binaries in density functional theory calculations within a local density approximation

    SciTech Connect

    Wang, Jianwei; Zhang, Yong; Wang, Lin-Wang

    2015-07-31

    We propose a systematic approach that can empirically correct three major errors typically found in a density functional theory (DFT) calculation within the local density approximation (LDA) simultaneously for a set of common cation binary semiconductors, such as III-V compounds, (Ga or In)X with X = N,P,As,Sb, and II-VI compounds, (Zn or Cd)X, with X = O,S,Se,Te. By correcting (1) the binary band gaps at high-symmetry points , L, X, (2) the separation of p-and d-orbital-derived valence bands, and (3) conduction band effective masses to experimental values and doing so simultaneously for common cation binaries, the resulting DFT-LDA-based quasi-first-principles method can be used to predict the electronic structure of complex materials involving multiple binaries with comparable accuracy but much less computational cost than a GW level theory. This approach provides an efficient way to evaluate the electronic structures and other material properties of complex systems, much needed for material discovery and design.

  7. SIMULTANEOUS DIFFERENTIAL EQUATION COMPUTER

    DOEpatents

    Collier, D.M.; Meeks, L.A.; Palmer, J.P.

    1960-05-10

    A description is given for an electronic simulator for a system of simultaneous differential equations, including nonlinear equations. As a specific example, a homogeneous nuclear reactor system including a reactor fluid, heat exchanger, and a steam boiler may be simulated, with the nonlinearity resulting from a consideration of temperature effects taken into account. The simulator includes three operational amplifiers, a multiplier, appropriate potential sources, and interconnecting R-C networks.

  8. Electrochemical sensors for the simultaneous determination of zinc, cadmium and lead using a Nafion/ionic liquid/graphene composite modified screen-printed carbon electrode.

    PubMed

    Chaiyo, Sudkate; Mehmeti, Eda; Žagar, Kristina; Siangproh, Weena; Chailapakul, Orawon; Kalcher, Kurt

    2016-04-28

    A simple, low cost, and highly sensitive electrochemical sensor, based on a Nafion/ionic liquid/graphene composite modified screen-printed carbon electrode (N/IL/G/SPCE) was developed to determine zinc (Zn(II)), cadmium (Cd(II)), and lead (Pb(II)) simultaneously. This disposable electrode shows excellent conductivity and fast electron transfer kinetics. By in situ plating with a bismuth film (BiF), the developed electrode exhibited well-defined and separate peaks for Zn(II), Cd(II), and Pb(II) by square wave anodic stripping voltammetry (SWASV). Analytical characteristics of the BiF/N/IL/G/SPCE were explored with calibration curves which were found to be linear for Zn(II), Cd(II), and Pb(II) concentrations over the range from 0.1 to 100.0 ng L(-1). With an accumulation period of 120 s detection limits of 0.09 ng mL(-1), 0.06 ng L(-1) and 0.08 ng L(-1) were obtained for Zn(II), Cd(II) and Pb(II), respectively using the BiF/N/IL/G/SPCE sensor, calculated as 3σ value of the blank. In addition, the developed electrode displayed a good repeatability and reproducibility. The interference from other common ions associated with Zn(II), Cd(II) and Pb(II) detection could be effectively avoided. Finally, the proposed analytical procedure was applied to detect the trace metal ions in drinking water samples with satisfactory results which demonstrates the suitability of the BiF/N/IL/G/SPCE to detect heavy metals in water samples and the results agreed well with those obtained by inductively coupled plasma mass spectrometry. PMID:27046207

  9. Simultaneous VLBA polarimetric observations of the v={1,2} J=1-0 and v=1, J=2-1 SiO maser emission toward VY CMa II: component-level polarization analysis.

    NASA Astrophysics Data System (ADS)

    Richter, L.; Kemball, A.; Jonas, J.

    2016-06-01

    This paper presents a component-level comparison of the polarized v=1 J =1-0, v=2 J=1-0 and v=1 J=2-1 SiO maser emission towards the supergiant star VY CMa at milliarcsecond-scale, as observed using the VLBA at λ = 7mm and λ = 3mm. An earlier paper considered overall maser morphology and constraints on SiO maser excitation and pumping derived from these data. The goal of the current paper is to use the measured polarization properties of individual co-spatial components detected across multiple transitions to provide constraints on several competing theories for the transport of polarized maser emission. This approach minimizes the significant effects of spatial blending. We present several diagnostic tests designed to distinguish key features of competing theoretical models for maser polarization. The number of coincident features is limited by sensitivity however, particularly in the v=1 J=2-1 transition at 86 GHz, and deeper observations are needed. Preliminary conclusions based on the current data provide some support for: i) spin-independent solutions for linear polarization; ii) the influence of geometry on the distribution of fractional linear polarization with intensity; and, iii) π/2 rotations in linear polarization position angle arising from transitions across the Van Vleck angle (sin 2θ = 2/3) between the maser line-of-sight and magnetic field. There is weaker evidence for several enumerated non-Zeeman explanations for circular polarization. The expected 2:1 ratio in circular polarization between J=1-0 and J=2-1 predicted by standard Zeeman theory cannot unfortunately be tested conclusively due to insufficient coincident components.

  10. Simultaneous VLBA polarimetric observations of the v = {1,2} J = 1-0 and v = 1, J = 2-1 SiO maser emission towards VY CMa II: component-level polarization analysis

    NASA Astrophysics Data System (ADS)

    Richter, L.; Kemball, A.; Jonas, J.

    2016-09-01

    This paper presents a component-level comparison of the polarized v = 1 J = 1-0, v = 2 J = 1-0 and v = 1 J = 2-1 SiO maser emission towards the supergiant star VY CMa at milliarcsecond-scale, as observed using the Very Long Baseline Array at λ = 7 and 3 mm. An earlier paper considered overall maser morphology and constraints on SiO maser excitation and pumping derived from these data. The goal of the current paper is to use the measured polarization properties of individual co-spatial components detected across multiple transitions to provide constraints on several competing theories for the transport of polarized maser emission. This approach minimizes the significant effects of spatial blending. We present several diagnostic tests designed to distinguish key features of competing theoretical models for maser polarization. The number of coincident features is limited by sensitivity however, particularly in the v = 1 J = 2-1 transition at 86 GHz, and deeper observations are needed. Preliminary conclusions based on the current data provide some support for: (i) spin-independent solutions for linear polarization; (ii) the influence of geometry on the distribution of fractional linear polarization with intensity; and, (iii) π/2 rotations in linear polarization position angle arising from transitions across the Van Vleck angle (sin 2θ = 2/3) between the maser line of sight and magnetic field. There is weaker evidence for several enumerated non-Zeeman explanations for circular polarization. The expected 2:1 ratio in circular polarization between J = 1-0 and J = 2-1 predicted by standard Zeeman theory cannot unfortunately be tested conclusively due to insufficient coincident components.

  11. Simultaneous shoulder and elbow dislocation

    PubMed Central

    Çobanoğlu, Mutlu; Yumrukcal, Feridun; Karataş, Cengiz; Duygun, Fatih

    2014-01-01

    Ipsilateral shoulder and elbow dislocation is very rare and only six articles are present in the literature mentioning this kind of a complex injury. With this presentation we aim to emphasise the importance of assessing the adjacent joints in patients with trauma in order not to miss any accompanying pathologies. We report a case of a 43-year-old female patient with ipsilateral right shoulder and elbow dislocation treated conservatively. The patient reported elbow pain when first admitted to emergency service but she was diagnosed with simultaneous ipsilateral shoulder and elbow injury and treated conservatively. As a more painful pathology may mask the additional ones, one should hasten to help before performing a complete evaluation. Any harm caused to the patient due to this reason would not be a complication but a malpractice. PMID:24859563

  12. Performance Boosting Additive

    NASA Technical Reports Server (NTRS)

    1999-01-01

    Mainstream Engineering Corporation was awarded Phase I and Phase II contracts from Goddard Space Flight Center's Small Business Innovation Research (SBIR) program in early 1990. With support from the SBIR program, Mainstream Engineering Corporation has developed a unique low cost additive, QwikBoost (TM), that increases the performance of air conditioners, heat pumps, refrigerators, and freezers. Because of the energy and environmental benefits of QwikBoost, Mainstream received the Tibbetts Award at a White House Ceremony on October 16, 1997. QwikBoost was introduced at the 1998 International Air Conditioning, Heating, and Refrigeration Exposition. QwikBoost is packaged in a handy 3-ounce can (pressurized with R-134a) and will be available for automotive air conditioning systems in summer 1998.

  13. Simultaneous SERS detection of copper and cobalt at ultratrace levels

    NASA Astrophysics Data System (ADS)

    Tsoutsi, Dionysia; Guerrini, Luca; Hermida-Ramon, Jose Manuel; Giannini, Vincenzo; Liz-Marzán, Luis M.; Wei, Alexander; Alvarez-Puebla, Ramon A.

    2013-06-01

    We report a SERS-based method for the simultaneous and independent determination of two environmental metallic pollutants, Cu(ii) and Co(ii). This was achieved by exploiting the coordination-sensitive Raman bands of a terpyridine (TPY) derivative for detecting transition metal ions. Changes in the vibrational SERS spectra of dithiocarbamate anchored terpyridine (TPY-DTC) were correlated as a function of each metal ion concentration, with limits of detection comparable to those of several conventional analytical methods. Simultaneous detection of ultratrace levels of Co(ii) in the presence of high Cu(ii) concentration was also demonstrated, supporting the potential of this sensing strategy for monitoring potable water supplies.

  14. Note on Magnetism and Simultaneity

    ERIC Educational Resources Information Center

    Huggins, Elisha

    2009-01-01

    The paper on "Magnetism and Simultaneity" by Adler provides an excellent new thought experiment involving the lack of simultaneity in Einstein's special relativity. Adler uses the lack of simultaneity rather than the Lorentz contraction to derive the formula for the magnetic force on a moving charged particle. Advantages of his derivation are that…

  15. Effects of adsorbents and copper(II) on activated sludge microorganisms and sequencing batch reactor treatment process.

    PubMed

    Ong, S A; Lim, P E; Seng, C E

    2003-10-31

    Wastewater treatment systems employing simultaneous adsorption and biodegradation processes have proven to be effective in treating toxic pollutants present in industrial wastewater. The objective of this study is to evaluate the effect of Cu(II) and the efficacy of the powdered activated carbon (PAC) and activated rice husk (ARH) in reducing the toxic effect of Cu(II) on the activated sludge microorganisms. The ARH was prepared by treatment with concentrated nitric acid for 15 h at 60-65 degrees C. The sequencing batch reactor (SBR) systems were operated with FILL, REACT, SETTLE, DRAW and IDLE modes in the ratio of 0.5:3.5:1:0.75:0.25 for a cycle time of 6 h. The Cu(II) and COD removal efficiency were 90 and 85%, respectively, in the SBR system containing 10 mg/l Cu(II) with the addition of 143 mg/l PAC or 1.0 g PAC per cycle. In the case of 715 mg/l ARH or 5.0 g ARH per cycle addition, the Cu(II) and COD removal efficiency were 85 and 92%, respectively. ARH can be used as an alternate adsorbent to PAC in the simultaneous adsorption and biodegradation wastewater treatment process for the removal of Cu(II). The specific oxygen uptake rate (SOUR) and kinetic studies show that the addition of PAC and ARH reduce the toxic effect of Cu(II) on the activated sludge microorganisms. PMID:14573344

  16. Reactivity of Fe(II) species associated with clay minerals.

    PubMed

    Hofstetter, Thomas B; Schwarzenbach, René P; Haderlein, Stefan B

    2003-02-01

    Mineral-bound Fe(II) species represent important natural reductants of pollutants in the anaerobic subsurface. At clay minerals, three types of Fe(II) species in fundamentally different chemical environments may be present simultaneously, i.e., structural Fe(II), Fe(II) complexed by surface hydroxyl groups, and Fe(II) bound by ion exchange. We investigated the accessibility and reactivity of these three types of Fe(II) species in suspensions of two different clay minerals containing either ferrous iron-bearing nontronite or iron-free hectorite. Nitroaromatic compounds (NACs) exhibiting different sorption behavior on clays were used to probe the reactivity of the various types of reduced iron species. The clay treatment allowed for a preparation of nontronite and hectorite surfaces with Fe(II) adsorbed by surface hydroxyl groups at the edge surfaces. Furthermore, hectorite suspensions with additional Fe(II) bound to the ion exchange sites at the basal siloxane surfaces were set up. We found that both structural Fe(II) and Fe(II) complexed by surface hydroxyl groups of nontronite reduced the NACs to anilines. An electron balance revealed that more than 10% of the total iron in nontronite was reactive Fe(II). Fe(II) bound by ion exchange did not contribute to the observed reduction of NACs. Reversible adsorption of the NACs at the basal siloxane surface of the clays strongly retarded NAC reduction, even in the presence of high concentrations of Fe(II) bound by ion exchange to the basal siloxane surfaces. Our work shows that in natural systems a fraction of the total Fe(II) present on clays may contribute to the pool of highly reactive Fe(II) species in the subsurface. Furthermore, this work may help to distinguish between Fe(II) species of different reactivity regarding pollutant reduction. Although structural iron in clays represents only a small fraction of the total iron pool in soils and aquifers, reactive Fe(II) species originating from the reduction of

  17. BORE II

    SciTech Connect

    2015-08-01

    Bore II, co-developed by Berkeley Lab researchers Frank Hale, Chin-Fu Tsang, and Christine Doughty, provides vital information for solving water quality and supply problems and for improving remediation of contaminated sites. Termed "hydrophysical logging," this technology is based on the concept of measuring repeated depth profiles of fluid electric conductivity in a borehole that is pumping. As fluid enters the wellbore, its distinct electric conductivity causes peaks in the conductivity log that grow and migrate upward with time. Analysis of the evolution of the peaks enables characterization of groundwater flow distribution more quickly, more cost effectively, and with higher resolution than ever before. Combining the unique interpretation software Bore II with advanced downhole instrumentation (the hydrophysical logging tool), the method quantifies inflow and outflow locations, their associated flow rates, and the basic water quality parameters of the associated formation waters (e.g., pH, oxidation-reduction potential, temperature). In addition, when applied in conjunction with downhole fluid sampling, Bore II makes possible a complete assessment of contaminant concentration within groundwater.

  18. BORE II

    Energy Science and Technology Software Center (ESTSC)

    2015-08-01

    Bore II, co-developed by Berkeley Lab researchers Frank Hale, Chin-Fu Tsang, and Christine Doughty, provides vital information for solving water quality and supply problems and for improving remediation of contaminated sites. Termed "hydrophysical logging," this technology is based on the concept of measuring repeated depth profiles of fluid electric conductivity in a borehole that is pumping. As fluid enters the wellbore, its distinct electric conductivity causes peaks in the conductivity log that grow and migratemore » upward with time. Analysis of the evolution of the peaks enables characterization of groundwater flow distribution more quickly, more cost effectively, and with higher resolution than ever before. Combining the unique interpretation software Bore II with advanced downhole instrumentation (the hydrophysical logging tool), the method quantifies inflow and outflow locations, their associated flow rates, and the basic water quality parameters of the associated formation waters (e.g., pH, oxidation-reduction potential, temperature). In addition, when applied in conjunction with downhole fluid sampling, Bore II makes possible a complete assessment of contaminant concentration within groundwater.« less

  19. Simultaneous Immersion Mirau Interferometry

    NASA Astrophysics Data System (ADS)

    Lyulko, Oleksandra

    acquisition challenging. This problem was resolved by integration of polarization optics into the optics of the attachment to enable simultaneous creation and spatial separation of two interferograms, which, combined with the background image, are used to reconstruct the intensity map of the specimen. Giving the name Simultaneous Immersion Mirau Interferometry to this approach, simultaneous acquisition of all interferograms per image has eliminated the issue of vibrations. The designed compound microscope attachment has been manufactured and tested; the system produces images of quality, sufficient to perform targeted cellular irradiation experiments.

  20. Simultaneous analysis and design

    NASA Technical Reports Server (NTRS)

    Haftka, R. T.

    1984-01-01

    Optimization techniques are increasingly being used for performing nonlinear structural analysis. The development of element by element (EBE) preconditioned conjugate gradient (CG) techniques is expected to extend this trend to linear analysis. Under these circumstances the structural design problem can be viewed as a nested optimization problem. There are computational benefits to treating this nested problem as a large single optimization problem. The response variables (such as displacements) and the structural parameters are all treated as design variables in a unified formulation which performs simultaneously the design and analysis. Two examples are used for demonstration. A seventy-two bar truss is optimized subject to linear stress constraints and a wing box structure is optimized subject to nonlinear collapse constraints. Both examples show substantial computational savings with the unified approach as compared to the traditional nested approach.

  1. Simultaneous Quantum Duel

    NASA Astrophysics Data System (ADS)

    Balthazar, Wagner F.; Huguenin, José A. O.; Schmidt, Alexandre G. M.

    2015-12-01

    We quantize the classical game of simultaneous two-person duel. In this game, the players Alice and Bob, have a two level system, for example, a spin 1/2 particle, which models alive and dead states. Through physical considerations we write up the unitary operator which represents the classical action of firing, which quantum mechanically is represented by flipping the opponent's spin and test its classical limits. We study three representative special cases of such duel where players start the duel: both alive; in a Bell state; and when one of them has her skills decreasing along the duel. We also present a proposal of experimental realization of this quantum game using twin photons produced by spontaneous parametric down conversion.

  2. World War II Homefront.

    ERIC Educational Resources Information Center

    Garcia, Rachel

    2002-01-01

    Presents an annotated bibliography that provides Web sites focusing on the U.S. homefront during World War II. Covers various topics such as the homefront, Japanese Americans, women during World War II, posters, and African Americans. Includes lesson plan sources and a list of additional resources. (CMK)

  3. The expression and role of insulin-like growth factor II in malignant hemangiopericytomas.

    PubMed

    Pavelić, K; Spaventi, S; Gluncić, V; Matejcić, A; Pavicić, D; Karapandza, N; Kusić, Z; Lukac, J; Dohoczky, C; Cabrijan, T; Pavelić, J

    1999-12-01

    Hemangiopericytoma is a rare soft tissue tumor originating from contractile pericapillary pericytes. To address the issue of molecular genetic events that participate in genesis and progression of hemangiopericytoma we analyzed insulin-like growth factor (IGF) II and IGF I receptor in 29 tumors collected from a human tumor bank network. Seven of these tumors were associated with severe hypoglycemia; six were retroperitoneal and one was located in the leg. Of 22 tumors tested 12 (54.5%) exhibited IGF II mRNA, while almost 90% (17 of 19) of hemangiopericytomas exhibited IGF I receptor mRNA. Sera from some patients whose tumors expressed IGF II mRNA contained elevated levels of IGF II. Removal of the tumor eliminated most of the IGF II immunoreactivity from the sera. The potential role of IGF II as a growth-promoting factor was examined on three malignant primary hemangiopericytoma cell cultures. Extracellular addition of IGF II significantly enhanced cell proliferation in a dose-dependent manner. Antisense oligodeoxynucleotides that specifically inhibit IGF II mRNA, at a concentration of 40 or 80 micrograms/ml, inhibited the growth of hemangiopericytoma cells significantly, by 40%. Simultaneous administration of antisense deoxyoligonucleotides to both IGF II and IGF I receptor inhibited tumor cell proliferation by even 80%. Our data suggest that tumor cells produce IGF II, and that this in turn stimulates their proliferation by autocrine mechanisms. PMID:10682323

  4. Simultaneous bilateral spontaneous pneumothorax.

    PubMed

    Graf-Deuel, E; Knoblauch, A

    1994-04-01

    We describe 12 patients with simultaneous bilateral spontaneous pneumothorax (SBSP). They represent 4 percent of patients with spontaneous pneumothorax seen at our hospital from 1971 to 1990. Five of the 12 had no underlying lung disease. In the seven remaining patients, SBSP was secondary to histiocytosis X, lymphangioleiomyomatosis, osteogenic sarcoma with pleural and pulmonary metastases, Hodgkin's disease, mesothelioma, cystic fibrosis, or miliary tuberculosis. Nineteen of the 56 patients with SBSP (34 percent) described in the literature (this series included) had pulmonary disease related to disorders of cells of mesenchymal origin. Emphysema and bullous lung disease were not associated with SBSP. Long-term prognosis was a function of pulmonary status. Four of the patients described herein died during the period reviewed. All suffered from severe underlying disease. In no case was SBSP the main cause of death. With timely treatment, the short-term prognosis is benign even for patients with underlying lung disease. Surgical pleurectomy should be attempted early, especially in SBSP secondary to underlying lung disease. PMID:8162740

  5. Analysis of simultaneous Skylab and ground based flare observations

    NASA Technical Reports Server (NTRS)

    Kulander, J. L.

    1976-01-01

    HeI and HeII resonance line data from Skylab were reduced, analyzed and compared with HeI D3 line intensities taken simultaneously from the Lockheed Rye Canyon Solar Observatory. Computer codes were developed for the calculation of total He line intensities and line profiles from model flare regions. These codes incorporate simultaneous solution of the line and continuum transport equations as needed together with the statistical equilibrium equations for a 30 level HeI, HeII, HeIII system. The energy level model consists of all terms through principal quantum number four. Interpretation of the observed data in terms of these parametric solutions and with simultaneous solution of the transport equations are discussed.

  6. A Demonstration of Simultaneous Electrochemiluminescence

    ERIC Educational Resources Information Center

    Ibanez, Jorge G.; Zavala-Araiza, Daniel; Sotomayor-Martinez Barranco, Biaani; Torres-Perez, Jonatan; Camacho-Zuniga, Claudia; Bohrmann-Linde, Claudia; Tausch, Michael W.

    2013-01-01

    Paired (simultaneous) electrochemical processes can increase energy savings in selected cases by using the reactions at both electrodes of an electrochemical cell to perform a desired process, as is the case in the commercially successful chlor-alkali process. In the demonstration described herein, simultaneous blue electrochemiluminescence (ECL)…

  7. A Phase II Study of Additional Four-Week Chemotherapy With Capecitabine During the Resting Periods After Six-Week Neoadjuvant Chemoradiotherapy in Patients With Locally Advanced Rectal Cancer

    PubMed Central

    Lee, Kyung Ha; Song, Min Sang; Park, Jun Boem; Kim, Jin Soo; Kang, Dae Young

    2013-01-01

    Purpose The aim of this study is to evaluate the efficacy and the safety of additional 4-week chemotherapy with capecitabine during the resting periods after a 6-week neoadjuvant chemoradiotherapy (NCRT) in patients with locally advanced rectal cancer. Methods Radiotherapy was delivered to the whole pelvis at a total dose of 50.4 Gy for 6 weeks. Oral capecitabine was administered at a dose of 825 mg/m2 twice daily for 10 weeks. Surgery was performed 2-4 weeks following the completion of chemotherapy. Results Between January 2010 and September 2011, 44 patients were enrolled. Forty-three patients underwent surgery, and 41 patients completed the scheduled treatment. Pathologic complete remission (pCR) was noted in 9 patients (20.9%). T down-staging and N down-staging were observed in 32 patients (74.4%) and 33 patients (76.7%), respectively. Grade 3 to 5 toxicity was noted in 5 patients (11.4%). The pCR rate was similar with the pCR rates obtained after conventional NCRT at our institute and at other institutes. Conclusion This study showed that additional 4-week chemotherapy with capecitabine during the resting periods after 6-week NCRT was safe, but it was no more effective than conventional NCRT. PMID:24278857

  8. Use of anodic stripping voltammetry to determine zinc(II), lead(II), and copper(II) in foods

    SciTech Connect

    Maksimkina, L.M.; Gus'kova, V.P.

    1988-01-20

    The existing standard procedure for the polarographic determination of Zn, Pb, and Cu, based on the cathodic polarization of a dropping mercury electrode, is laborious and time-consuming and allows one to determine the above-mentioned trace elements only when they are separated beforehand. We consider the possibility of using anodic stripping voltammetry with a mercury film electrode for the simultaneous determination of Zn(II), Pb(II), and Cu(II) in foods.

  9. Part I: Reverse-docking studies of a squaramide-catalyzed conjugate addition of a diketone to a nitro-olefin Part II: The development of ChemSort: an education game for organic chemistry

    NASA Astrophysics Data System (ADS)

    Granger, Jenna Christine

    Part 1: Reverse-docking studies of a squaramide-catalyzed conjugate addition of a diketone to a nitro-olefin. Asymmetric organocatalysis, the catalysis of asymmetric reactions by small organic molecules, is a rapidly growing field within organic synthesis. The ability to rationally design organocatalysts is therefore of increasing interest to organic chemists. Computational chemistry is quickly proving to be an extremely successful method for understanding and predicting the roles of organocatalysts, and therefore is certain to be of use in the rational design of such catalysts. A methodology for reverse-docking flexible organocatalysts to rigid transition state models of asymmetric reactions has been previously developed by the Deslongchamps group. The investigation of Rawal's squaramide-based organocatalyst for the addition of a diketone to a nitro-olefin is described, and the results of the reverse docking of Rawal's catalyst to the geometry optimized transition state models of the uncatalyzed reaction for both the R and S-product enantiomers are presented. The results of this study indicate a preference for binding of the organocatalyst to the R-enantiomer transition state model with a predicted enantiomeric excess of 99%, which is consistent with the experimental results. A plausible geometric model of the transition state for the catalyzed reaction is also presented. The success of this study demonstrates the credibility of using reverse docking methods for the rational design of asymmetric organocatalysts. Part 2: The development of ChemSort: an educational game for organic chemistry. With the advent of the millennial learner, we need to rethink traditional classroom approaches to science learning in terms of goals, approaches, and assessments. Digital simulations and games hold much promise in support of this educational shift. Although the idea of using games for education is not a new one, well-designed computer-based "serious games" are only beginning to

  10. Rapid extraction and reverse phase-liquid chromatographic separation of mercury(II) and methylmercury in fish samples with inductively coupled plasma mass spectrometric detection applying oxygen addition into plasma.

    PubMed

    Döker, Serhat; Boşgelmez, İffet İpek

    2015-10-01

    A simple and sensitive procedure was developed for extraction and speciation of mercury in fish. Species separation was accomplished with reverse phase-high performance liquid chromatography (HPLC) hyphenated to inductively coupled plasma mass spectrometry (ICP-MS). Oxygen addition into plasma allowed use of organic-rich mobile phase, achieving species separation in 4 min. Mercury species extraction was achieved by microwave exposure for 2 min at mild conditions (60°C, pH 2.0), avoiding necessity of neutralizing sample prior to injection in HPLC, and reducing number of sample preparation steps, analytical source of errors and inter conversion of species. Limit of detection for entire procedure was found to be 0.2 and 0.1 ng g(-1) for mercuric ion and methylmercury, respectively. The method was applied to certified reference materials (TORT-2 and DORM-2) and commercialized fish samples (Mullus barbatus, Sparus aurata, Trachurus mediterraneus, Mugil soiuy, Dicentrarchus labrax, and Pomatomus saltatrix) from Black Sea. PMID:25872437

  11. Effect of Inert Gas Additive Species on Cl(2) High Density Plasma Etching of Compound Semiconductors: Part II. InP, InSb, InGaP and InGaAs

    SciTech Connect

    Abernathy, C.R.; Cho, H.; Hahn, Y.B.; Hays, D.C.; Jung, K.B.; Pearton, S.J.; Shul, R.J.

    1998-12-17

    The effects of the additive noble gases He, Ar and Xe on chlorine-based Inductively Coupled Plasma etching of InP, InSb, InGaP and InGaAs were studied as a function of source power, chuck power and discharge composition. The etch rates of all materials with C12/He and C12/Xe are greater than with C12/Ar. Etch rates in excess of 4.8 pndmin for InP and InSb with C12/He or C12/Xe, 0.9 pndmin for InGaP with C12/Xe, and 3.8 prdmin for InGaAs with Clz/Xe were obtained at 750 W ICP power, 250 W rf power, - 1570 C12 and 5 mTorr. All three plasma chemistries produced smooth morphologies for the etched InGaP surfaces, while the etched surface of InP showed rough morphology under all conditions.

  12. REVIEW OF THE NEGOTIATION OF THE MODEL PROTOCOL ADDITIONAL TO THE AGREEMENT(S) BETWEEN STATE(S) AND THE INTERNATIONAL ATOMIC ENERGY AGENCY FOR THE APPLICATION OF SAFEGUARDS, INFCIRC/540 (Corrected) VOLUME II/III IAEA COMMITTEE 24, Major Issues Underlying the Model Additional Protocol (1996-1997).

    SciTech Connect

    Rosenthal, M.D.; Saum-Manning, L.; Houck, F.

    2010-01-01

    Volume I of this Review traces the origins of the Model Additional Protocol. It covers the period from 1991, when events in Iraq triggered an intensive review of the safeguards system, until 1996, when the IAEA Board of Governors established Committee 24 to negotiate a new protocol to safeguards agreement. The period from 1991-1996 set the stage for this negotiation and shaped its outcome in important ways. During this 5-year period, many proposals for strengthening safeguards were suggested and reviewed. Some proposals were dropped, for example, the suggestion by the IAEA Secretariat to verify certain imports, and others were refined. A rough consensus was established about the directions in which the international community wanted to go, and this was reflected in the draft of an additional protocol that was submitted to the IAEA Board of Governors on May 6, 1996 in document GOV/2863, Strengthening the Effectiveness and Improving the Efficiency of the Safeguards System - Proposals For Implementation Under Complementary Legal Authority, A Report by the Director General. This document ended with a recommendation that, 'the Board, through an appropriate mechanism, finalize the required legal instrument taking as a basis the draft protocol proposed by the Secretariat and the explanation of the measures contained in this document.'

  13. Approximating incompatible von Neumann measurements simultaneously

    SciTech Connect

    Heinosaari, Teiko; Jivulescu, Maria Anastasia; Reitzner, Daniel; Ziman, Mario

    2010-09-15

    We study the problem of performing orthogonal qubit measurements simultaneously. Since these measurements are incompatible, one has to accept additional imprecision. An optimal joint measurement is the one with the least possible imprecision. All earlier considerations of this problem have concerned only joint measurability of observables, while in this work we also take into account conditional state transformations (i.e., instruments). We characterize the optimal joint instrument for two orthogonal von Neumann instruments as being the Lueders instrument of the optimal joint observable.

  14. Simultaneous update of priority structures

    SciTech Connect

    Biswas, J.; Browne, J.C.

    1987-01-01

    To avoid centralized bottlenecks, data structures for multiple computer systems must be simultaneously updatable and yet must have some coherent and consistent state. This can be achieved through judicious partitioning of system data structures and control of access to them in such a manner that (1) either different processes operate upon disjoint segments of a given structure; or (2) processes operate upon the same datum object, in a controlled manner. Partitioning of data structures can be by structure or content. It can also occur at multiple times. In this paper we demonstrate content partitioning of a k-ary tree data structure at runtime, to realize a simultaneously updatable priority queue. The tree algorithms are then generalized to banyan data structures and shown to possess attractive properties of simultaneous update and throughput.

  15. Comparative studies of aerosol extinction measurements made by the SAM II and SAGE II satellite experiments

    NASA Technical Reports Server (NTRS)

    Yue, Glenn K.; Mccormick, M. P.; Chu, W. P.; Wang, P.; Osborn, M. T.

    1989-01-01

    Results from the Stratospheric Aerosol Measurement (SAM) II and Stratospheric Aerosol and Gas Experiment (SAGE) II are compared for measurement locations which are coincident in time and space. At 1.0 micron, the SAM II and SAGE II aerosol extinction profiles are similar within their measurement errors. In addition, sunrise and sunset aerosol extinction data at four different wavelengths are compared for occasions when the SAGE II and SAM II measurements are nearly coincident in space and about 12 hours apart.

  16. Belle II production system

    NASA Astrophysics Data System (ADS)

    Miyake, Hideki; Grzymkowski, Rafal; Ludacka, Radek; Schram, Malachi

    2015-12-01

    The Belle II experiment will record a similar quantity of data to LHC experiments and will acquire it at similar rates. This requires considerable computing, storage and network resources to handle not only data created by the experiment but also considerable amounts of simulated data. Consequently Belle II employs a distributed computing system to provide the resources coordinated by the the DIRAC interware. DIRAC is a general software framework that provides a unified interface among heterogeneous computing resources. In addition to the well proven DIRAC software stack, Belle II is developing its own extension called BelleDIRAC. BelleDIRAC provides a transparent user experience for the Belle II analysis framework (basf2) on various environments and gives access to file information managed by LFC and AMGA metadata catalog. By unifying DIRAC and BelleDIRAC functionalities, Belle II plans to operate an automated mass data processing framework named a “production system”. The Belle II production system enables large-scale raw data transfer from experimental site to raw data centers, followed by massive data processing, and smart data delivery to each remote site. The production system is also utilized for simulated data production and data analysis. Although development of the production system is still on-going, recently Belle II has prepared prototype version and evaluated it with a large scale simulated data production. In this presentation we will report the evaluation of the prototype system and future development plans.

  17. Simultaneous stabilization using genetic algorithms

    SciTech Connect

    Benson, R.W.; Schmitendorf, W.E. . Dept. of Mechanical Engineering)

    1991-01-01

    This paper considers the problem of simultaneously stabilizing a set of plants using full state feedback. The problem is converted to a simple optimization problem which is solved by a genetic algorithm. Several examples demonstrate the utility of this method. 14 refs., 8 figs.

  18. Combining Simultaneous with Temporal Masking

    ERIC Educational Resources Information Center

    Hermens, Frouke; Herzog, Michael H.; Francis, Gregory

    2009-01-01

    Simultaneous and temporal masking are two frequently used techniques in psychology and vision science. Although there are many studies and theories related to each masking technique, there are no systematic investigations of their mutual relationship, even though both techniques are often applied together. Here, the authors show that temporal…

  19. Envisioning Curriculum as Six Simultaneities

    ERIC Educational Resources Information Center

    Hussain, Hanin; Conner, Lindsey; Mayo, Elaine

    2014-01-01

    This paper uses the discourse of complexity thinking to envision curriculum as six partial and coupled facets that exist simultaneously: curriculum as structure, curriculum as process, curriculum as content, curriculum as teaching, curriculum as learning and curriculum as activity. Such a curriculum is emergent and self-organising. It is emergent…

  20. Best Practices and Simultaneous Compliance

    EPA Science Inventory

    This wrap-up presentation to the workshop covers several topics concerning how lead and copper compliance under the Lead and Copper Rule should be integrated into an overall “simultaneous compliance” framework with other organizations. The LCR requires “optimization” of lead leve...

  1. Juno II

    NASA Technical Reports Server (NTRS)

    1959-01-01

    The Juno II launch vehicle, shown here, was a modified Jupiter Intermediate-Range Ballistic missionile, developed by Dr. Wernher von Braun and the rocket team at Redstone Arsenal in Huntsville, Alabama. Between December 1958 and April 1961, the Juno II launched space probes Pioneer III and IV, as well as Explorer satellites VII, VIII and XI.

  2. Impact of the Addition of Carboplatin and/or Bevacizumab to Neoadjuvant Once-per-Week Paclitaxel Followed by Dose-Dense Doxorubicin and Cyclophosphamide on Pathologic Complete Response Rates in Stage II to III Triple-Negative Breast Cancer: CALGB 40603 (Alliance)

    PubMed Central

    Sikov, William M.; Berry, Donald A.; Perou, Charles M.; Singh, Baljit; Cirrincione, Constance T.; Tolaney, Sara M.; Kuzma, Charles S.; Pluard, Timothy J.; Somlo, George; Port, Elisa R.; Golshan, Mehra; Bellon, Jennifer R.; Collyar, Deborah; Hahn, Olwen M.; Carey, Lisa A.; Hudis, Clifford A.; Winer, Eric P.

    2015-01-01

    Purpose One third of patients with triple-negative breast cancer (TNBC) achieve pathologic complete response (pCR) with standard neoadjuvant chemotherapy (NACT). CALGB 40603 (Alliance), a 2 × 2 factorial, open-label, randomized phase II trial, evaluated the impact of adding carboplatin and/or bevacizumab. Patients and Methods Patients (N = 443) with stage II to III TNBC received paclitaxel 80 mg/m2 once per week (wP) for 12 weeks, followed by doxorubicin plus cyclophosphamide once every 2 weeks (ddAC) for four cycles, and were randomly assigned to concurrent carboplatin (area under curve 6) once every 3 weeks for four cycles and/or bevacizumab 10 mg/kg once every 2 weeks for nine cycles. Effects of adding these agents on pCR breast (ypT0/is), pCR breast/axilla (ypT0/isN0), treatment delivery, and toxicities were analyzed. Results Patients assigned to either carboplatin or bevacizumab were less likely to complete wP and ddAC without skipped doses, dose modification, or early discontinuation resulting from toxicity. Grade ≥ 3 neutropenia and thrombocytopenia were more common with carboplatin, as were hypertension, infection, thromboembolic events, bleeding, and postoperative complications with bevacizumab. Employing one-sided P values, addition of either carboplatin (60% v 44%; P = .0018) or bevacizumab (59% v 48%; P = .0089) significantly increased pCR breast, whereas only carboplatin (54% v 41%; P = .0029) significantly raised pCR breast/axilla. More-than-additive interactions between the two agents could not be demonstrated. Conclusion In stage II to III TNBC, addition of either carboplatin or bevacizumab to NACT increased pCR rates, but whether this will improve relapse-free or overall survival is unknown. Given results from recently reported adjuvant trials, further investigation of bevacizumab in this setting is unlikely, but the role of carboplatin could be evaluated in definitive studies, ideally limited to biologically defined patient subsets most likely

  3. 78 FR 76789 - Additional Connect America Fund Phase II Issues

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-12-19

    ... Support Disbursements. In the USF/ICC Transformation Order, 76 FR 73830, November 29, 2011, the Commission... Transformation Order and FNPRM, 76 FR 73830, November 29, 2011 and 76 FR 78384, December 16, 2011, included...

  4. Siloxane containing addition polyimides. II - Acetylene terminated polyimides

    NASA Technical Reports Server (NTRS)

    Maudgal, S.; St. Clair, T. L.

    1984-01-01

    Acetylene terminated polyimide oligomers having a range of molecular weights have been synthesized by reacting bis (gamma-aminopropyl) tetramethyldisiloxane, aminophenylacetylene and 3, 3', 4, 4' benzophenonetetracarboxylic dianhydride in different molar ratios. The prepolymers were isolated and characterized for melt flow and cure properties. They show promise as adhesives for bonding titanium to titanium and as matrix resins for graphite cloth reinforced composites. The most promising system has been blended in varying proportions with Thermid 600, a commercially available acetylene terminated polyimide oligomer, and the mixtures have been tested for application as composite matrix resins.

  5. Polyimide processing additives

    NASA Technical Reports Server (NTRS)

    Pratt, J. R.; St. Clair, T. L.; Burks, H. D.; Stoakley, D. M.

    1987-01-01

    A method has been found for enhancing the melt flow of thermoplastic polyimides during processing. A high molecular weight 422 copoly(amic acid) or copolyimide was fused with approximately 0.05 to 5 pct by weight of a low molecular weight amic acid or imide additive, and this melt was studied by capillary rheometry. Excellent flow and improved composite properties on graphite resulted from the addition of a PMDA-aniline additive to LARC-TPI. Solution viscosity studies imply that amic acid additives temporarily lower molecular weight and, hence, enlarge the processing window. Thus, compositions containing the additive have a lower melt viscosity for a longer time than those unmodified.

  6. [Food additives and healthiness].

    PubMed

    Heinonen, Marina

    2014-01-01

    Additives are used for improving food structure or preventing its spoilage, for example. Many substances used as additives are also naturally present in food. The safety of additives is evaluated according to commonly agreed principles. If high concentrations of an additive cause adverse health effects for humans, a limit of acceptable daily intake (ADI) is set for it. An additive is a risk only when ADI is exceeded. The healthiness of food is measured on the basis of nutrient density and scientifically proven effects. PMID:24772784

  7. New Insight into GO, Cadmium(II), Phosphate Interaction and Its Role in GO Colloidal Behavior.

    PubMed

    Ren, Xuemei; Wu, Qunyan; Xu, Huan; Shao, Dadong; Tan, Xiaoli; Shi, Weiqun; Chen, Changlun; Li, Jiaxing; Chai, Zhifang; Hayat, Tasawar; Wang, Xiangke

    2016-09-01

    This study establishes the relationship between the graphene oxide (GO) colloidal behavior and the co-adsorption of Cd(II) and phosphate (P(V)) on GO. Results reveal that the interactions among GO, Cd(II), and P(V) exhibit a significant dependence on solution chemistry and addition sequences and that these interactions subsequently affect the GO colloidal behavior. The GO aggregation is pH-dependent at pH < 4.0 and depends apparently on the binding ability of Cd(II) to GO at pH > 4.0. When the components were added simultaneously, the presence of P(V) enhances the GO binding capacity toward Cd(II), confirmed by theoretical calculation, resulting in the greater destabilizing influence of Cd(II) + P(V) on GO than Cd(II) at pH 3.0-9.5, while the formation of Cd3(PO4)2 precipitate leads to a lower destabilizing influence of Cd(II) + P(V) on GO than Cd(II) at pH > 9.5. Both pH and addition sequence affect the destabilizing ability of Cd(II) + P(V). These new insights are expected to provide valuable information not only for the application of GO as a potential adsorbent in multicomponent systems for heavy metal ion and oxyanion co-removal but also for the fate and risk assessment of GO after serving as heavy metal ion and oxyanion carrier. PMID:27479690

  8. Simultaneous observation of a hot explosion by NST and IRIS

    NASA Astrophysics Data System (ADS)

    Kim, Yeon-Han; Yurchyshyn, Vasyl; Bong, Su-Chan; Cho, Il-Hyun; Cho, Kyung-Suk; Lee, Jaejin; Lim, Eun-Kyung; Park, Young-Deuk; Yang, Heesu; Ahn, Kwangsu; Goode, Philip R.; Jang, Bi-Ho

    2015-09-01

    We present the first simultaneous observations of so-called “hot explosions” in the cool atmosphere of the Sun made by the New Solar Telescope (NST) of Big Bear Solar Observatory and the Interface Region Imaging Spectrograph (IRIS) in space. The data were obtained during the joint IRIS-NST observations on 2014 July 30. The explosion of interest started around 19:20 UT and lasted for about 10 minutes. Our findings are as follows: (1) the IRIS brightening was observed in three channels of slit-jaw images, which cover the temperature range from 4000 to 80,000 K; (2) during the brightening, the Si iv emission profile showed a double-peaked shape with highly blue and redshifted components (-40 and 80 km s-1) (3) wing brightening occurred in Hα and Ca ii 8542 Å bands and related surges were observed in both bands of the NST Fast Imaging Solar Spectrograph (FISS) instrument; (4) the elongated granule, seen in NST TiO data, is clear evidence of the emergence of positive flux to trigger the hot explosion; (5) the brightening in Solar Dynamics Observatory/Atmospheric Imaging Assembly 1600 Å images is quite consistent with the IRIS brightening. These observations suggest that our event is a hot explosion that occurred in the cool atmosphere of the Sun. In addition, our event appeared as an Ellerman bomb (EB) in the wing of Hα, although its intensity is weak and the vertical extent of the brightening seems to be relatively high compared with the typical EBs.

  9. Simultaneous saccharification and fermentation of hemicellulose to butanol by a non-sporulating Clostridium species.

    PubMed

    Li, Tinggang; He, Jianzhong

    2016-11-01

    Production of lignocellulosic butanol has drawn increasing attention. However, currently few microorganisms can produce biofuels, particularly butanol, from lignocellulosic biomass via simultaneous saccharification and fermentation. Here we report discovery of a wild-type, mesophilic Clostridium sp. strain MF28 that ferments xylan to produce butanol (up to 3.2g/L) without the addition of saccharolytic enzymes and without any chemical pretreatments. Application of selective pressure from 2-deoxy-d-glucose facilitated isolation of strain MF28, which exhibits inactivation of genes (gid and ccp genes) responsible for carbon catabolite repression, thus allowing strain MF28 to simultaneously ferment a combination of glucose (30g/L), xylose (15g/L), and arabinose (15g/L) to produce 11.9g/L of butanol. Strain MF28 possesses several unique features: (i) non-sporulating, (ii) no acetone/ethanol, (iii) complete hemicellulose-binding enzymatic domain, and (iv) absence of carbon catabolite repression. These unique characteristics demonstrate the industrial potential of strain MF28 for cost-effective biofuel generation from lignocellulosic biomass. PMID:27513648

  10. Photosystem II

    ScienceCinema

    James Barber

    2010-09-01

    James Barber, Ernst Chain Professor of Biochemistry at Imperial College, London, gives a BSA Distinguished Lecture titled, "The Structure and Function of Photosystem II: The Water-Splitting Enzyme of Photosynthesis."