Science.gov

Sample records for infrared laser radiation

  1. Prophylaxis and treatment of acute radiation ulcers in rats with low-power infrared laser radiation

    NASA Astrophysics Data System (ADS)

    Kursova, Larisa V.; Kaplan, Michael A.; Nikitina, Rosa G.; Maligina, Antonina I.

    1999-12-01

    Exposure of radiation ulcers in rats to low-power infrared laser radiation (LPLR) (wavelength--890 nm, pulse power--6 W, frequency--150 and 300 Hz, irradiation time--10 min) noticeably accelerates their healing, reduces exudative processes, increases number of specialized cells in wound. Application of LPLR prior to radiation damage decreases ulcer dimensions.

  2. Laser welding of plastics transparent to near-infrared radiation

    NASA Astrophysics Data System (ADS)

    Sato, Kimitoshi; Kurosaki, Yasuo; Saito, Takushi; Satoh, Isao

    2002-06-01

    This paper deals with a development of laser welding of colored plastics. Welding of thermoplastics using near-IR lasers has been seen in wide industrial application. Most of thermoplastics are transparent to near-IR laser. Particular characteristic of near-IR laser radiation has the ability to heat the interface between the transparent part and absorbent one colored with pigments. However, it is difficult to weld a pair of transparent materials by a laser beam, since there is no absorption region within them. In this paper, the influence of near-IR transparent plastics on the yield strength of their weldments has been studied: various colored plastics transparent to diode laser radiation were tested as the welding material. The heat transfer within a welding system was also analyzed and assessed the appropriate absorptivity and transmittance of overlapping colored plastic.

  3. Photochemical synthesis of disilane from silane with infrared laser radiation

    SciTech Connect

    Zavelovich, J. ); Lyman, J.L. )

    1989-07-27

    The authors report the clean and efficient conversion of silane to disilane by CO{sub 2} laser irradiation. The direct irradiation of pure silane at high pressures (from 75 to 1,700 Torr) converts silane to disilane with high selectivity and with efficient use of the absorbed laser radiation. Hydrogen is the only other major volatile product, and the production of solid products is minimal. The proposed mechanism of the photochemical reaction includes (1) collisionally enhanced absorption of the laser radiation by silane, (2) collisional deexcitation of the vibrationally excited silane, (3) concurrent decomposition to SiH{sub 2} and H{sub 2}, (4) production of vibrationally excited disilane by SiH{sub 2} insertion into a silane Si-H bond, (5) collisional quenching of the excited disilane, and (6) rapid cooling of the irradiated gas by thermal expansion. They support the proposed mechanism by additional experiments and model calculations.

  4. Photoblepharokeratoconjunctivitis caused by invisible infrared radiation emitted from a green laser pointer.

    PubMed

    Khedr, Yahya A H; Khedr, Abdulla H

    2014-01-01

    There are a wide variety of laser pointers sold to the general public. Among those are the high-powered diode-pumped solid-state lasers (>5 mW), which do not follow the laser safety regulations for packing, and are sold as regular lasers without the infrared (IR) filters. In this case report, we encountered a patient with photoblepharokeratoconjunctivitis caused by the invisible IR radiations emitted from a green laser pointer. Owing to the thermal effect of the invisible IR rays led to the disease. PMID:24618868

  5. Pulsed mid-infrared radiation from spectral broadening in laser wakefield simulations

    SciTech Connect

    Zhu, W.; Palastro, J. P.; Antonsen, T. M.

    2013-07-15

    Spectral red-shifting of high power laser pulses propagating through underdense plasma can be a source of ultrashort mid-infrared (MIR) radiation. During propagation, a high power laser pulse drives large amplitude plasma waves, depleting the pulse energy. At the same time, the large amplitude plasma wave provides a dynamic dielectric response that leads to spectral shifting. The loss of laser pulse energy and the approximate conservation of laser pulse action imply that spectral red-shifts accompany the depletion. In this paper, we investigate, through simulation, the parametric dependence of MIR generation on pulse energy, initial pulse duration, and plasma density.

  6. Microprocessing of human hard tooth tissues surface by mid-infrared erbium lasers radiation

    NASA Astrophysics Data System (ADS)

    Belikov, Andrey V.; Shatilova, Ksenia V.; Skrypnik, Alexei V.

    2015-03-01

    A new method of hard tooth tissues laser treatment is described. The method consists in formation of regular microdefects on tissue surface by mid-infrared erbium laser radiation with propagation ratio M2<2 (Er-laser microprocessing). Proposed method was used for preparation of hard tooth tissues surface before filling for improvement of bond strength between tissues surface and restorative materials, microleakage reduction between tissues surface and restorative materials, and for caries prevention as a result of increasing microhardness and acid resistance of tooth enamel.

  7. Melanin and the cellular effects of ultrashort-pulse, near-infrared laser radiation

    NASA Astrophysics Data System (ADS)

    Glickman, Randolph D.; Kumar, Neeru; Rockwell, Benjamin A.; Noojin, Gary D.; Denton, Michael L.; Stolarski, David J.

    2003-07-01

    Our research into laser bioeffects has increasingly focused on cytotoxic mechanisms affecting genomic expression and programmed cellular stress responses. In the context of DNA damage, we previously reported that more DNA strand breaks were produced in cultured retinal pigment epithelium (RPE) cells exposed to ultrashort pulse, than to CW, near-infrared (NIR) laser radiation. To test the hypothesis that RPE melanin was the cellular chromophore responsible for mediating this damage, the experiments were repeated with a line of human-derived RPE cells that could be grown in culture expressing varying levels of pigmentation. Lightly-pigmented cells were either unexposed, or exposed to the output of a Ti:Sapphire laser producing 810 nm light in mode-locked pulses (48-fsec at 80 MHz), or as CW radiation. Cells were irradiated at 160 W/cm2 or 80 W/cm2 (the estimated ED50 or half-ED50 for a retinal lesion). Immediately following the laser exposure, cells were processed for the comet assay. Longer "comet" tails and larger "comet" areas indicated more DNA strand breaks. In lightly-pigmented RPE cells, the overall comet assay differences among the laser-exposed groups were smaller than those observed in our earlier experiments which utilized highly pigmented primary cells. The comet tail lengths of cells exposed to the mode-locked pulses at the ED50, however, were significantly longer than those of the controls or the CW-exposed cells. The other comet assay parameters examined (tail moment, comet area) did not show consistent differences among the groups. While these results support the involvement of melanin in the ultrashort pulse laser-induced damage to DNA, they do not exclude the involvement of other cellular chromophores. Some preliminary experiments describing other measures of cellular stress responses to laser-induced oxidative stress are described.

  8. Infrared Lasers in Chemistry.

    ERIC Educational Resources Information Center

    John, Phillip

    1982-01-01

    Selected infrared laser chemistry topics are discussed including carbon dioxide lasers, infrared quanta and molecules, laser-induced chemistry, structural isomerization (laser purification, sensitized reactions, and dielectric breakdown), and fundamental principles of laser isotope separation, focusing on uranium isotope separation. (JN)

  9. Q-switching of mid-infrared Er:YAG laser and its radiation delivery system

    NASA Astrophysics Data System (ADS)

    Jelinkova, Helena; Koranda, Petr; Nemec, Michal; Sulc, Jan; Cech, Miroslav; Miyagi, Mitsunobu; Shi, Yi-Wei; Matsuura, Yuji

    2004-09-01

    Q-switching of mid-infrared Er:YAG laser was obtained with an electro-optical shutter. For that the LiNbO3 Pockels cell was used in transversal quarter-wave arrangement with the Brewster angle cut faces used as a polarizer. Parameters and dependences of this Q-switched system were investigated, i.e. a pulse length and generated pulse energy, delay between switching of flashlamp and Q-switch circuit, high voltage applied on Pockels cell were measured and optimized. The resulted giant pulse length and energy was 60 ns and 55 mJ, respectively. This generated pulse was obtained for the applied voltage around 1.4 kV and for the optimum delay value 450 us. Problem of mid-infrared giant pulse delivery, which is needed for various technological applications, was solved by a specially designed cyclic olefin polymer coated silver hollow glass (COP/Ag) waveguide. Parameters of this waveguide were: diameter 700/850 um and length 1 m. The measured transmission was 74 % which corresponded to delivered intensity 86 MW/cm2. Q-switched Er:YAG laser radiation in connection with this special delivery system gives a possibility of the surgical treatment in many medicine branches, for example ophthalmology, urology or dentistry.

  10. Stable 1.25 watts CW far infrared laser radiation at the 119 micron methanol line

    NASA Technical Reports Server (NTRS)

    Farhoomand, Jam; Pickett, Herbert M.

    1987-01-01

    Far-infrared CW radiation of 1.25 watts has been obtained at the 119 micron methanol line with a CO2 pump power of 125 watts, and the maximum frequency fluctuation of the free running laser is measured to be less than + or - 100 kHz per hour. Reflecting optics have been used, when possible, to minimize CO2 degradation, and the frequency stability is ensured by cooling the input and output couplers. The input and output assemblies within the lasing medium are enclosed to minimize the external effects on the cavity length and to eliminate the mechanical instabilities associated with the use of bellows. The vibrational bottle-neck is broken by cooling the resonator wall to 5 deg and adding He as the buffer gas.

  11. Effects of Infrared Laser Radiation on the In Vitro Isomerization of All-Trans Retinal to 11-Cis Retinal

    PubMed Central

    Liegner, J.; Taboada, J.; Tsin, A. T. C.

    2015-01-01

    The in vitro effect of infrared laser light on the isomerization of all-trans retinal dissolved in an ether/hexane and also an ethanol solvent was studied. Pulsed laser energy at 1064 nm was used to drive the molecular reconfiguration of all-trans retinal to 11-cis retinal. High pressure liquid chromatography (HPLC) was used to quantify the conversion. Overall isomerization was minimal (0.2 percent to 1.0 percent), yet, a significant difference in isomerization due to pulsed infrared laser energy over non-modulated monochromatic laser light was detected (up to 168 percent difference). Potentially, pulsed laser radiation tuned to the ethylenic stretch frequency of the C11=C12 bond of retinal may induce rotational changes to the chromophore. PMID:26321787

  12. Generation of acoustic waves by focused infrared neodymium-laser radiation

    NASA Astrophysics Data System (ADS)

    Ward, Barry

    1991-02-01

    When the radiation from a sufficiently powerful pulsed laser is focused into the transparent gaseous, liquid or solid media, dielectric breakdown may occur around the beam waist giving rise to a short-lived high-temperature plasma which quickly heats the surrounding material. As a consequence of various energy-coupling mechanisms, this phenomenon causes the emission of one or more high-frequency ultrasonic acoustic waves whose speeds of propagation are dependent upon the physical properties of the host medium. In the high-speed photographic studies described, the 1.06 micron near-infrared radiation from an 8-ns, 10-mJ Q-switched Nd:YAG laser is focused in or onto a variety of fluid and solid materials. The rapid variations in density around the resulting plasma events are visualized using a Mach-Zehnder interferometer with a sub-nanosecond dye-laser light source and a video-imaging system. Calculations of the corresponding transient pressure distributions are then enacted from the digitally-recorded interferograms using a semi-automatic procedure under the control of a personal computer. Measurements of position, displacement, and velocity are also carried out using the same optical apparatus in schlieren and focused shadowgraph high-speed photographic measurements. The experimental work outlined in the following chapters is divided into three broad fields of interest. In the first of these, a study of the laser-generation of spherical shock waves in atmospheric air is carried out. In the second, the neodymium-laser beam is focused onto different solid-fluid interfaces resulting in the formation of bulk longitudinal and shear waves and surface acoustic waves. The interactions of these waves with various obstacles and defects are investigated with reference to their application to non-destructive testing. In the third and most important field, a detailed study of the dynamics of laser-induced cavitation bubbles in water is carried out. With regard to the associated

  13. Application and possible mechanisms of combining LLLT (low level laser therapy), infrared hyperthermia and ionizing radiation in the treatment of cancer

    NASA Astrophysics Data System (ADS)

    Abraham, Edward H.; Woo, Van H.; Harlin-Jones, Cheryl; Heselich, Anja; Frohns, Florian

    2014-02-01

    Benefit of concomitant infrared hyperthermia and low level laser therapy and ionizing radiation is evaluated in this study. The purpose/objectives: presentation with locally advanced bulky superficial tumors is clinically challenging. To enhance the efficacy of chemotherapy and IMRT (intensity-modulated radiation therapy) and/or electron beam therapy we have developed an inexpensive and clinically effective infrared hyperthermia approach that combines black-body infrared radiation with halogen spectrum radiation and discrete wave length infrared clinical lasers LLLT. The goal is to produce a composite spectrum extending from the far infrared to near infrared and portions of the visible spectrum with discrete penetrating wavelengths generated by the clinical infrared lasers with frequencies of 810 nm and/or 830 nm. The composite spectrum from these sources is applied before and after radiation therapy. We monitor the surface and in some cases deeper temperatures with thermal probes, but use an array of surface probes as the limiting safe thermal constraint in patient treatment while at the same time maximizing infrared entry to deeper tissue layers. Fever-grade infrared hyperthermia is produced in the first centimeters while non-thermal infrared effects act at deeper tissue layers. The combination of these effects with ionizing radiation leads to improved tumor control in many cancers.

  14. Coherent infrared radiation from the ALS generated via femtosecond laser modulation of the electron beam

    SciTech Connect

    Byrd, J.M.; Hao, Z.; Martin, M.C.; Robin, D.S.; Sannibale, F.; Schoenlein, R.W.; Venturini, M.; Zholents, A.A.; Zolotorev, M.S.

    2004-07-01

    Interaction of an electron beam with a femtosecond laser pulse co-propagating through a wiggler at the ALS produces large modulation of the electron energies within a short {approx}100 fs slice of the electron bunch. Propagating around the storage ring, this bunch develops a longitudinal density perturbation due to the dispersion of electron trajectories. The length of the perturbation evolves with a distance from the wiggler but is much shorter than the electron bunch length. This perturbation causes the electron bunch to emit short pulses of temporally and spatially coherent infrared light which are automatically synchronized to the modulating laser. The intensity and spectra of the infrared light were measured in two storage ring locations for a nominal ALS lattice and for an experimental lattice with the higher momentum compaction factor. The onset of instability stimulated by laser e-beam interaction had been discovered. The infrared signal is now routinely used as a sensitive monitor for a fine tuning of the laser beam alignment during data accumulation in the experiments with femtosecond x-ray pulses.

  15. Infrared radiation and inversion population of CO2 laser levels in Venusian and Martian atmospheres

    NASA Technical Reports Server (NTRS)

    Gordiyets, B. F.; Panchenko, V. Y.

    1983-01-01

    Formation mechanisms of nonequilibrium 10 micron CO2 molecule radiation and the possible existence of a natural laser effect in the upper atmospheres of Venus and Mars are theoretically studied. An analysis is made of the excitation process of CO2 molecule vibrational-band levels (with natural isotropic content) induced by direct solar radiation in bands 10.6, 9.4, 4.3, 2.7 and 2.0 microns. The model of partial vibrational-band temperatures was used in the case. The problem of IR radiation transfer in vibrational-rotational bands was solved in the radiation escape approximation.

  16. Infrared laser system

    DOEpatents

    Cantrell, Cyrus D.; Carbone, Robert J.; Cooper, Ralph

    1982-01-01

    An infrared laser system and method for isotope separation may comprise a molecular gas laser oscillator to produce a laser beam at a first wavelength, Raman spin flip means for shifting the laser to a second wavelength, a molecular gas laser amplifier to amplify said second wavelength laser beam to high power, and optical means for directing the second wavelength, high power laser beam against a desired isotope for selective excitation thereof in a mixture with other isotopes. The optical means may include a medium which shifts the second wavelength high power laser beam to a third wavelength, high power laser beam at a wavelength coincidental with a corresponding vibrational state of said isotope and which is different from vibrational states of other isotopes in the gas mixture.

  17. Infrared laser system

    DOEpatents

    Cantrell, Cyrus D.; Carbone, Robert J.; Cooper, Ralph S.

    1977-01-01

    An infrared laser system and method for isotope separation may comprise a molecular gas laser oscillator to produce a laser beam at a first wavelength, Raman spin flip means for shifting the laser to a second wavelength, a molecular gas laser amplifier to amplify said second wavelength laser beam to high power, and optical means for directing the second wavelength, high power laser beam against a desired isotope for selective excitation thereof in a mixture with other isotopes. The optical means may include a medium which shifts the second wavelength high power laser beam to a third wavelength, high power laser beam at a wavelength coincidental with a corresponding vibrational state of said isotope and which is different from vibrational states of other isotopes in the gas mixture.

  18. SiC absorption of near-infrared laser radiation at high temperatures

    NASA Astrophysics Data System (ADS)

    Adelmann, B.; Hellmann, R.

    2016-07-01

    We report on a theoretical and experimental investigation of the temperature-dependent optical absorption of nitrogen-doped 4H-SiC for a temperature range between room temperature and the decomposition point. The theoretical model is based on free carrier absorption including the temperature dependence of the electron mobility. With respect to laser material processing of silicon carbide, the analysis focusses on a near-infrared wavelength range. At room temperature, the calculated absorption is in excellent agreement to transmission and reflection measurements. For the experimental study of the absorption at higher temperatures induced by intense 1070-nm laser irradiation, a two-color pyrometer is employed with the thermal emission of the laser interaction zone being collected coaxial to the impinging laser. Exemplarily, the simulated temperature-dependent absorption is used to determine the heating of a 0.4-mm-thick 4H-SiC specimen during laser irradiation and compared to the experimentally determined temperature. In an initial time domain of the irradiation with an attained temperature below 1350 K, the simulated and measured temperatures are in good agreement. Above 1350 K, however, the measured temperature reveals a sharp and fast increase up to 2100 K which is not predicted by the model. This discrepancy is attributed to a strong additional absorption mechanism caused by carbonization at the surface which is confirmed by EDX analysis.

  19. Analgesic effect of simultaneous exposure to infrared laser radiation and μT magnetic field in rats

    NASA Astrophysics Data System (ADS)

    Cieslar, Grzegorz; Mrowiec, Janina; Kasperczyk, Slawomir; Sieron-Stoltny, Karolina; Sieron, Aleksander

    2008-03-01

    The aim of the experiment was to estimate the effect of repeated simultaneous exposures to infrared laser radiation and μT variable magnetic field used in magnetostimulation on pain perception in rats, as well as the involvement of endogenous opioid system in the mechanism of this effect. In experimental group clean-shaven scull of male Wistar rats placed individually in a specially designed plastic chamber were simultaneously exposed to infrared laser radiation (wavelength - 855 nm, mean power - 4,1 mW, energy density - 30 J/cm2) and variable magnetic field of saw-like shape of impulse, at a frequency of basic impulse 180-195 Hz and mean induction value of 120 μT generated by magneto-laser applicator of device for magnetostimulation Viofor JPS (Med & Life, Poland) 12 minutes daily for 2 periods of 5 consecutive days, with 2 days-lasting break between them, while control animals were sham-exposed. The pain perception was determined by means of "hot plate" test on the basis of calculated analgesic index. As a result of repeated exposures a significant increase in analgesic index persisting also till 14 th day after the end of a cycle of exposures was observed. This analgesic effect was inhibited by prior i.p. injection of opioid antagonist - Naloxone.

  20. Infrared absorption change in single-walled carbon nanotubes observed by combination spectroscopy of synchrotron radiation and laser.

    PubMed

    Azuma, Junpei; Itoh, Minoru; Koike, Masahiro; Kamada, Masao; Endo, Morinobu

    2006-11-01

    The Drude tail due to photo-excited carriers in single-walled carbon nanotubes (SWNTs) has been observed in the mid-infrared region by using combination spectroscopy of synchrotron radiation and Ti:sapphire laser. It is found that the density of photo-excited carriers increases as the sample temperature is raised from 12 to 300 K, and their lifetime is of the order of minutes at 300 K. These facts suggest that the movement of photo-excited carriers is largely affected by some extrinsic defect, thus resulting in the long-lasting Drude reflection in SWNTs. PMID:17057323

  1. Spatial temperature distribution in human hairy and glabrous skin after infrared CO2 laser radiation

    PubMed Central

    2010-01-01

    Background CO2 lasers have been used for several decades as an experimental non-touching pain stimulator. The laser energy is absorbed by the water content in the most superficial layers of the skin. The deeper located nociceptors are activated by passive conduction of heat from superficial to deeper skin layers. Methods In the current study, a 2D axial finite element model was developed and validated to describe the spatial temperature distribution in the skin after infrared CO2 laser stimulation. The geometry of the model was based on high resolution ultrasound scans. The simulations were compared to the subjective pain intensity ratings from 16 subjects and to the surface skin temperature distributions measured by an infrared camera. Results The stimulations were sensed significantly slower and less intense in glabrous skin than they were in hairy skin (MANOVA, p < 0.001). The model simulations of superficial temperature correlated with the measured skin surface temperature (r > 0.90, p < 0.001). Of the 16 subjects tested; eight subjects reported pricking pain in the hairy skin following a stimulus of 0.6 J/cm2 (5 W, 0.12 s, d1/e2 = 11.4 mm) only two reported pain to glabrous skin stimulation using the same stimulus intensity. The temperature at the epidermal-dermal junction (depth 50 μm in hairy and depth 133 μm in glabrous skin) was estimated to 46°C for hairy skin stimulation and 39°C for glabrous skin stimulation. Conclusions As compared to previous one dimensional heat distribution models, the current two dimensional model provides new possibilities for detailed studies regarding CO2 laser stimulation intensity, temperature levels and nociceptor activation. PMID:21059226

  2. Generating Tunable Far-Infrared Laser Sidebands

    NASA Technical Reports Server (NTRS)

    Pickett, H. M.; Farhoomand, J.

    1986-01-01

    New tunable source extends infrared spectroscopy into far infrared wavelengths. Frequency-Tunable far-infrared radiation produced by mixing of fixed-frequency far-infrared laser beam with output of frequency-tunable klystron. By sweeping klystron frequency in synchronism with video display of detector output, one obtains direct presentation of absorption-cell spectrum. Immediate applications are local oscillator for heterodyne systems and tunable source for spectroscopy.

  3. Infrared laser bone ablation

    SciTech Connect

    Nuss, R.C.; Fabian, R.L.; Sarkar, R.; Puliafito, C.A.

    1988-01-01

    The bone ablation characteristics of five infrared lasers, including three pulsed lasers (Nd:YAG, lambda = 1064 micron; Hol:YSGG, lambda = 2.10 micron; and Erb:YAG, lambda = 2.94 micron) and two continuous-wave lasers (Nd:YAG, lambda = 1.064 micron; and CO/sub 2/, lambda = 10.6 micron), were studied. All laser ablations were performed in vitro, using moist, freshly dissected calvarium of guinea pig skulls. Quantitative etch rates of the three pulsed lasers were calculated. Light microscopy of histologic sections of ablated bone revealed a zone of tissue damage of 10 to 15 micron adjacent to the lesion edge in the case of the pulsed Nd:YAG and the Erb:YAG lasers, from 20 to 90 micron zone of tissue damage for bone ablated by the Hol:YSGG laser, and 60 to 135 micron zone of tissue damage in the case of the two continuous-wave lasers. Possible mechanisms of bone ablation and tissue damage are discussed.

  4. The Berkeley tunable far infrared laser spectrometers

    NASA Technical Reports Server (NTRS)

    Blake, G. A.; Laughlin, K. B.; Cohen, R. C.; Busarow, K. L.; Gwo, D.-H.

    1991-01-01

    A detailed description is presented for a tunable far infrared laser spectrometer based on frequency mixing of an optically pumped molecular gas laser with tunable microwave radiation in a Schottky point contact diode. The system has been operated on over 30 laser lines in the range 10-100/cm and exhibits a maximum absorption sensitivity near one part in a million. Each laser line can be tuned by + or - 110 GHz with first-order sidebands.

  5. Dysprosium thiogallate laser: source of mid-infrared radiation at 2.4, 4.3, and 5.4 µm

    NASA Astrophysics Data System (ADS)

    Jelinkova, H.; Doroshenko, M. E.; Osiko, V. V.; Jelínek, M.; Šulc, J.; Němec, M.; Vyhlídal, D.; Badikov, V. V.; Badikov, D. V.

    2016-08-01

    Various Dy:PbGa2S4 laser-active material energy transitions originating from the 6H9/2 + 6F11/2 or 6H11/2 energy level were investigated, and the mid-infrared radiation generation has been demonstrated. The Dy:PbGa2S4 laser was pumped by a 1.32-µm free-running Nd:YAG laser or laser diode radiation corresponding to the Dy:PbGa2S4 absorption peak. The Dy:PbGa2S4 crystal was placed in the stable optical resonator with the mirrors chosen according to the required generated wavelength. New laser wavelengths of 2.4 and 5.4 µm were generated from the Dy:PbGa2S4 laser at room temperature. Laser output characteristics at 4.3 µm are also presented.

  6. Delivery of midinfrared (6 to 7-microm) laser radiation in a liquid environment using infrared-transmitting optical fibers.

    PubMed

    Mackanos, Mark A; Jansen, E Duco; Shaw, Brandon L; Sanghera, Jas S; Aggarwal, Ishwar; Katzir, Abraham

    2003-10-01

    Ablation at wavelengths near lambda = 6.45 microm results in tissue ablation with minimal collateral damage (< 40 microm) yet yields a high ablation rate that is useful for human surgery. However, delivery of this wavelength has been limited to that in air and thus to applications in which the target tissue can be readily exposed. The goal of this study is to investigate the potential of a pulsed infrared laser at lambda = 6.45 microm for noncontact ablation in a liquid environment. To this end we investigated fiber delivery in combination with the use of infrared transparent liquids. Transmission characteristics and damage thresholds for two types of fiber materials (silver halide and arsenic sulfide), for high-power pulsed laser radiation were determined using the Mark III free electron laser. Both fibers had comparable bulk losses (0.54 dB/m and 0.62 dB/m, respectively) while the arsenic sulfide fibers showed more coupling losses (37 versus 27%). Damage thresholds were higher in arsenic sulfide fibers than in silver halide fibers (1.12 GW/cm2 versus 0.54 GW/cm2), but both fibers were sufficient to deliver radiant exposures well above the ablation threshold in tissue. Seven different perfluorocarbon liquids (PFCLs), known for their transparency at lambda = 2.94 microm, were investigated and their optical transmission was determined using Fourier transform infrared and direct Beer's law measurements. All of the PFCLs tested had similar values for an absorption coefficient mu(a) at a given wavelength (mu(a) = 0.05 mm(-1) at lambda = 2.94 microm and mu(a) is approximately 3 mm(-1) at lambda = 6.45 microm). Pump-probe imaging showed the ablation sequence (lambda = 6.45 microm) at the fiber tip in a water environment, which revealed a fast expanding and collapsing bubble. In contrast, the volatile PF-5060 showed no fast bubble expansion and collapse, but rather formation of nontransient gas bubbles. Perfluorodecalin did not show any bubble formation at the radiant

  7. Retinal thermal damage threshold dependence on exposure duration for the transitional near-infrared laser radiation at 1319 nm.

    PubMed

    Wang, Jiarui; Jiao, Luguang; Jing, Xiaomin; Chen, Hongxia; Hu, Xiangjun; Yang, Zaifu

    2016-05-01

    The retinal damage effects induced by transitional near-infrared (NIR) lasers have been investigated for years. However, the damage threshold dependence on exposure duration has not been revealed. In this paper, the in-vivo retinal damage ED50 thresholds were determined in chinchilla grey rabbits for 1319 nm laser radiation for exposure durations from 0.1 s to 10 s. The incident corneal irradiance diameter was fixed at 5 mm. The ED50 thresholds given in terms of the total intraocular energy (TIE) for exposure durations of 0.1, 1 and 10 s were 1.36, 6.33 and 28.6 J respectively. The ED50 thresholds were correlated by a power law equation, ED50 = 6.31t (0.66) [J] where t is time [s], with correlation coefficient R = 0.9999. There exists a sufficient safety margin (factor of 28~60) between the human ED50 thresholds derived from the rabbit and the maximum permissible exposure (MPE) values in the current laser safety standards. PMID:27231639

  8. Retinal thermal damage threshold dependence on exposure duration for the transitional near-infrared laser radiation at 1319 nm

    PubMed Central

    Wang, Jiarui; Jiao, Luguang; Jing, Xiaomin; Chen, Hongxia; Hu, Xiangjun; Yang, Zaifu

    2016-01-01

    The retinal damage effects induced by transitional near-infrared (NIR) lasers have been investigated for years. However, the damage threshold dependence on exposure duration has not been revealed. In this paper, the in-vivo retinal damage ED50 thresholds were determined in chinchilla grey rabbits for 1319 nm laser radiation for exposure durations from 0.1 s to 10 s. The incident corneal irradiance diameter was fixed at 5 mm. The ED50 thresholds given in terms of the total intraocular energy (TIE) for exposure durations of 0.1, 1 and 10 s were 1.36, 6.33 and 28.6 J respectively. The ED50 thresholds were correlated by a power law equation, ED50 = 6.31t0.66 [J] where t is time [s], with correlation coefficient R = 0.9999. There exists a sufficient safety margin (factor of 28~60) between the human ED50 thresholds derived from the rabbit and the maximum permissible exposure (MPE) values in the current laser safety standards. PMID:27231639

  9. Corneal thermal damage threshold dependence on the exposure duration for near-infrared laser radiation at 1319 nm

    NASA Astrophysics Data System (ADS)

    Wang, Jiarui; Jiao, Luguang; Chen, Hongxia; Yang, Zaifu; Hu, Xiangjun

    2016-01-01

    The corneal damage effects induced by 1319-nm transitional near-infrared laser have been investigated for years. However, the damage threshold dependence on exposure duration has not been revealed. The in vivo corneal damage thresholds (ED50s) were determined in New Zealand rabbits for 1319-nm laser radiation for exposure durations from 75 ms to 10 s. An additional corneal ED50 was determined at 1338 nm for a 5-ms exposure. The incident corneal irradiance diameter was fixed at 2 mm for all exposure conditions to avoid the influence of spot size on threshold. The ED50s given in terms of the corneal radiant exposure for exposure durations of 5 ms, 75 ms, 0.35 s, 2 s, and 10 s were 39.4, 51.5, 87.2, 156.3, and 311.1 J/cm2, respectively. The 39.4 J/cm2 was derived from the ED50 for 1338 nm (27.0 J/cm2). The ED50s for exposure durations of 75 ms to 10 s were correlated by a power law equation, ED50=128.9t0.36 in J/cm2, where t was the input in the unit of second, with correlation coefficient (R) of 0.997. Enough safe margins existed between the ED50s and the maximum permitted exposures from current laser safety standard.

  10. Generation of Widely Tunable Fourier-Transform Pulsed Terahertz Radiation Using Narrowband Near-Infrared Laser Radiation

    NASA Astrophysics Data System (ADS)

    Liu, Jinjun; Haase, Christa; Merkt, Frédéric

    2009-06-01

    Widely tunable, Fourier-transform-limited pulses of terahertz (THz) radiation have been generated by optical frequency deference using (i) crystals of the highly nonlinear organic salt 4-N,N-dimethylamino-4^'-N^'-methyl stilbazolium tosylate (DAST), (ii) zinc telluride (ZnTe) crystals, and (iii) gallium phosphide (GaP) crystals. Outputs from two narrowband (Δν<1 MHz, λ˜800 nm) cw titanium-doped sapphire (Ti:Sa) ring lasers with a well-controlled frequency difference were shaped into pulses using acousto-optic modulators, coupled into an optical fiber, pulse amplified in Nd:YAG-pumped Ti:Sa crystals and used as optical sources to pump the THz nonlinear crystals. The THz radiation was detected over a broad frequency range and its bandwidth was determined to be ˜10 MHz. Absorption spectra of gas phase molecules including HF and OCS using the THz source will be presented.

  11. [Improved results of the trachea scar stenosis treatment by inclusion in the complex therapy of combined application diprospan and low-intensity infrared laser radiation].

    PubMed

    Israfilova, S B; Gasymov, É M

    2013-09-01

    The experience of treating 61 patients over the rumen of stenosis of the trachea was summarizes. To improve the results suggested inclusion complex diprospan treatment in combination with low intensity infrared laser radiation. The advantages of the proposed method of treatment of tracheal stenosis scarring are reduced severity of chronic inflammation, reducing the proliferation of granulation tissue. PMID:24501929

  12. Infrared laser hemotherapy in cerebral ischemia modeling

    NASA Astrophysics Data System (ADS)

    Musienko, Julia I.; Nechipurenko, Natalia I.

    2003-10-01

    Use of intravenous laser irradiation of blood (ILIB) is considered to be the most effective method of laser therapy and its application is expedient pathogenetically in the ischemic disturbances. The aim of this study is to investigate ILIB influence with infrared laser (IL) with 860 nm wavelength on hemostasis, acid-base status (ABS) of blood in normal rabbits and after modeling of local ischemia of brain (LIB). Experimental cerebral ischemia is characterized by development of hypercoagulation syndrom and metabolic acidosis. ILIB with infrared radiation of 2.0 mW power provokes hypocoagulation in intact animals. Application of ILIB in rabbits after LIB contributes for hemostasis and acid-base status normalizing compared to operated animals. IL radiation with 8,5 mW power results in marked hemostatic activation in all animals. Therefore, beneficial effect of low power laser radiation (LPLR) manifests in narrow power diapason in experimental brain ischemia.

  13. A review of laser-pumped infrared lasers

    NASA Technical Reports Server (NTRS)

    Chen, K. Y.

    1985-01-01

    The lasing mechanisms are reviewed of molecules that have demonstrated laser action in the laboratories with laser emissions in the spectral range from 3 to 35 microns. A list of lasants and laser mechanisms are defined. The pumping sources for these lasers are mainly infrared lasers; however, the case in which excitation of bromine atoms at 2.71 microns by a flashlamp as energy input is also included in the review. A conceptual drawing of lasing mechanisms is shown. Three pumping mechanisms are shown, the first being the direct-pumped system in which the lasant molecule absorbs the infrared radiation from pump laser directly, and it is excited into the upper laser level from the ground state. The second system is the indirect-pumped system where the infrared-pump laser first excites an absorbing molecule which stores its vibrational energy. Through collision this energy is transferred to the lasant molecule, populating the upper laser level. In the third system, i.e., in a Br2-CO2 mixture, a flashlamp replaces the infrared laser as the pump source for the absorbing molecule.

  14. STRONG FIELD PHYSICS WITH MID INFRARED LASERS.

    SciTech Connect

    POGORELSKY,I.V.

    2001-08-27

    Mid-infrared gas laser technology promises to become a unique tool for research in strong-field relativistic physics. The degree to which physics is relativistic is determined by a ponderomotive potential. At a given intensity, a 10 {micro}m wavelength CO{sub 2} laser reaches a 100 times higher ponderomotive potential than the 1 {micro}m wavelength solid state lasers. Thus, we can expect a proportional increase in the throughput of such processes as laser acceleration, x-ray production, etc. These arguments have been confirmed in proof-of-principle Thomson scattering and laser acceleration experiments conducted at BNL and UCLA where the first terawatt-class CO{sub 2} lasers are in operation. Further more, proposals for the 100 TW, 100 fs CO{sub 2} lasers based on frequency-chirped pulse amplification have been conceived. Such lasers can produce physical effects equivalent to a hypothetical multi-petawatt solid state laser. Ultra-fast mid-infrared lasers will open new routes to the next generation electron and ion accelerators, ultra-bright monochromatic femtosecond x-ray and gamma sources, allow to attempt the study of Hawking-Unruh radiation, and explore relativistic aspects of laser-matter interactions. We review the present status and experiments with terawatt-class CO{sub 2} lasers, sub-petawatt projects, and prospective applications in strong-field science.

  15. Pollution Encrustation Removal by Means of Combined Ultraviolet and Infrared Laser Radiation: The Application of this Innovative Methodology on the Surface of the Parthenon West Frieze

    NASA Astrophysics Data System (ADS)

    Pouli, P.; Frantzikinaki, K.; Papakonstantinou, E.; Zafiropulos, V.; Fotakis, C.

    This study refers to the innovative laser cleaning methodology developed at FORTH IESL on the combination of ultraviolet and infrared laser radiation emitted from a Q-switched Nd:YAG laser for the successful removal of pollution encrustation from marble substrates. The above-mentioned methodology is presented as regards its successful application on the fragile and demanding surface of the Parthenon West Frieze in collaboration with the Committee for the Preservation of the Acropolis Monuments. The aim of this intervention was to remove encrustation, accumulated on the stone due to the atmospheric pollution, without any discoloration or structural alteration to the original surface. The preliminary experiments on all the possible substrates and encrustations present on the surface of the Acropolis monuments and the laser cleaning parameters are presented in detail.

  16. Coherent tunable far infrared radiation

    NASA Technical Reports Server (NTRS)

    Jennings, D. A.

    1989-01-01

    Tunable, CW, FIR radiation has been generated by nonlinear mixing of radiation from two CO2 lasers in a metal-insulator-metal (MIM) diode. The FIR difference-frequency power was radiated from the MIM diode antenna to a calibrated InSb bolometer. FIR power of 200 nW was generated by 250 mW from each of the CO2 lasers. Using the combination of lines from a waveguide CO2 laser, with its larger tuning range, with lines from CO2, N2O, and CO2-isotope lasers promises complete coverage of the entire FIR band with stepwise-tunable CW radiation.

  17. Near infrared laser ocular bioeffects

    SciTech Connect

    Lund, D.J.; Beatrice, E.S.

    1989-05-01

    Thresholds for laser chorioretinal injury in the red end of the visible spectrum and the near-infrared (IR-A) spectral regions are presented. An unpredicted wavelength dependence of the injury threshold for single Q-switched pulses is demonstrated. Four lasers were used to determine thresholds at 40 wavelengths between 532 nm and 1064 nm: a ruby laser, a neodymium:YAG-pumped dye laser, an erbium:YLF laser and an alexandrite laser. Despite many careful and repeated efforts to determine a cause for the variation due to possible variations in the lasers or other aspects of the experimental technique and due to biological absorption properties of the eye, there is no complete or obvious explanation for the significant variations of threshold with small changes in wavelength. The implications of these findings for laser safety standards are presented.

  18. Infrared Radiation and Planetary Temperature

    NASA Astrophysics Data System (ADS)

    Pierrehumbert, Raymond T.

    2011-11-01

    Infrared radiative transfer theory, one of the most productive physical theories of the past century, has unlocked myriad secrets of the universe including that of planetary temperature and the connection between global warming and greenhouse gases.

  19. Effects of near-infrared laser radiation on the survival and inflammatory potential of Candida spp. involved in the pathogenesis of chemotherapy-induced oral mucositis.

    PubMed

    Clemente, A M; Rizzetto, L; Castronovo, G; Perissi, E; Tanturli, M; Cozzolino, F; Cavalieri, D; Fusi, F; Cialdai, F; Vignali, L; Torcia, M G; Monici, M

    2015-10-01

    Candida spp. usually colonize ulcerative lesions of atrophic mucosa in patients with chemotherapy-induced oral mucositis inducing severe inflammation. The spread of antifungal-resistant strains strongly encouraged the search of complementary or alternative therapeutic strategies to cure inflamed mucosa. In this paper, we studied the effects of a near-infrared (NIR) laser system with dual-wavelength emission (808 nm + 904 nm) on the survival and inflammatory potential of C. albicans, C. glabrata, and C. parapsilosis. Laser treatment was performed with a Multiwave Locked System laser. Survival and apoptosis of fungal strains were evaluated by colony-forming units (CFU) counting and annexin V staining. Cytokine production was evaluated by ImmunoPlex array. Laser treatment significantly affected the survival of Candida spp. by inducing apoptosis and induced a lower production of inflammatory cytokines by dendritic cells compared to untreated fungi. No differences in the survival and inflammatory potential were recorded in treated or untreated Saccharomyces cerevisiae cells, used as the control non-pathogenic microorganism. Laser treatment altered the survival and inflammatory potential of pathogenic Candida spp. These data provide experimental support to the use of NIR laser radiation as a co-adjuvant of antifungal therapy in patients with oral mucositis (OM) complicated by Candida infections. PMID:26173694

  20. Optical and infrared lasers

    NASA Technical Reports Server (NTRS)

    Javan, A.

    1978-01-01

    Quantum mechanical predictions for the gain of an optically pumped CW FIR laser are presented for cases in which one or both of the pump and FIR transitions are pressure or Doppler broadened. The results are compared to those based on the rate equation model. Some of the quantum mechanical predictions are verified in CH3OH.

  1. Advanced infrared laser modulator development

    NASA Technical Reports Server (NTRS)

    Cheo, P. K.; Wagner, R.; Gilden, M.

    1984-01-01

    A parametric study was conducted to develop an electrooptic waveguide modulator for generating continuous tunable sideband power from an infrared CO2 laser. Parameters included were the waveguide configurations, microstrip dimensions device impedance, and effective dielectric constants. An optimum infrared laser modulator was established and was fabricated. This modulator represents the state-of-the-art integrated optical device, which has a three-dimensional topology to accommodate three lambda/4 step transformers for microwave impedance matching at both the input and output terminals. A flat frequency response of the device over 20 HGz or = 3 dB) was achieved. Maximum single sideband to carrier power greater than 1.2% for 20 W microwave input power at optical carrier wavelength of 10.6 microns was obtained.

  2. Banana Dehydration Utilizing Infrared Radiation

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The enzyme of polyphenol oxidase (PPO) has been found to be the main cause of browning in bananas. Infrared radiation (IR) drying could be used to minimize biochemical degradation hence eliminating the need for pre-treatments. This study was to investigate quality characteristics of bananas dried ...

  3. Transient Infrared Measurement of Laser Absorption Properties of Porous Materials

    NASA Astrophysics Data System (ADS)

    Marynowicz, Andrzej

    2016-06-01

    The infrared thermography measurements of porous building materials have become more frequent in recent years. Many accompanying techniques for the thermal field generation have been developed, including one based on laser radiation. This work presents a simple optimization technique for estimation of the laser beam absorption for selected porous building materials, namely clinker brick and cement mortar. The transient temperature measurements were performed with the use of infrared camera during laser-induced heating-up of the samples' surfaces. As the results, the absorbed fractions of the incident laser beam together with its shape parameter are reported.

  4. Synthesis of materials with infrared and ultraviolet lasers

    SciTech Connect

    Lyman, J.L.

    1988-01-01

    This paper discusses three divergent examples of synthesis of materials with lasers. The three techniques are: (1) infrared (CO/sub 2/) laser synthesis of silane (SiH/sub 4/) from disilane (Si/sub 2/H/sub 6/); (2) excimer (ArF) laser production of fine silicon powders from methyl- and chloro-substituted silanes; and, (3) excimer (KrF) laser production of fine metallic powders by laser ablation. The mechanism for each process is discussed along with some conclusions about the features of the laser radiation that enable each application. 19 refs., 12 figs., 2 tabs.

  5. Parametric infrared tunable laser system

    NASA Technical Reports Server (NTRS)

    Garbuny, M.; Henningsen, T.; Sutter, J. R.

    1980-01-01

    A parametric tunable infrared laser system was built to serve as transmitter for the remote detection and density measurement of pollutant, poisonous, or trace gases in the atmosphere. The system operates with a YAG:Nd laser oscillator amplifier chain which pumps a parametric tunable frequency converter. The completed system produced pulse energies of up to 30 mJ. The output is tunable from 1.5 to 3.6 micrometers at linewidths of 0.2-0.5 /cm (FWHM), although the limits of the tuning range and the narrower line crystals presently in the parametric converter by samples of the higher quality already demonstrated is expected to improve the system performance further.

  6. Mid-infrared laser filaments in the atmosphere

    PubMed Central

    Mitrofanov, A. V.; Voronin, A. A.; Sidorov-Biryukov, D. A.; Pugžlys, A.; Stepanov, E. A.; Andriukaitis, G.; Flöry, T.; Ališauskas, S.; Fedotov, A. B.; Baltuška, A.; Zheltikov, A. M.

    2015-01-01

    Filamentation of ultrashort laser pulses in the atmosphere offers unique opportunities for long-range transmission of high-power laser radiation and standoff detection. With the critical power of self-focusing scaling as the laser wavelength squared, the quest for longer-wavelength drivers, which would radically increase the peak power and, hence, the laser energy in a single filament, has been ongoing over two decades, during which time the available laser sources limited filamentation experiments in the atmosphere to the near-infrared and visible ranges. Here, we demonstrate filamentation of ultrashort mid-infrared pulses in the atmosphere for the first time. We show that, with the spectrum of a femtosecond laser driver centered at 3.9 μm, right at the edge of the atmospheric transmission window, radiation energies above 20 mJ and peak powers in excess of 200 GW can be transmitted through the atmosphere in a single filament. Our studies reveal unique properties of mid-infrared filaments, where the generation of powerful mid-infrared supercontinuum is accompanied by unusual scenarios of optical harmonic generation, giving rise to remarkably broad radiation spectra, stretching from the visible to the mid-infrared. PMID:25687621

  7. Diffuse Cosmic Infrared Background Radiation

    NASA Technical Reports Server (NTRS)

    Dwek, Eli

    2002-01-01

    The diffuse cosmic infrared background (CIB) consists of the cumulative radiant energy released in the processes of structure formation that have occurred since the decoupling of matter and radiation following the Big Bang. In this lecture I will review the observational data that provided the first detections and limits on the CIB, and the theoretical studies explaining the origin of this background. Finally, I will also discuss the relevance of this background to the universe as seen in high energy gamma-rays.

  8. An infrared search for extraterrestrial laser signals

    NASA Technical Reports Server (NTRS)

    Betz, A.

    1986-01-01

    The focus of project SETI is on microwave frequencies, where receivers fundamentally have the best sensitivity for the detection of narrow band signals. Such receivers, when coupled to existing radio telescopes, form an optimum system for broad area searches over the sky. Detection of narrow band infrared signals is best done with a laser heterodyne reciever similar in function to a microwave spectral line receiver. A receiver was built for astrophysical observations at 30 THz (10 microns) and the spectrometer is being adapted for SETI work. The receiver uses a small CO2 laser as the local oscillator, a HgCdTe diode as the photomixer, and a multichannel intermediate frequency (IF) filterbank. An advanced multichannel IF processor is now being built to detect infrared line radiation in 1000 spectral channels each 1 MHz wide. When completed this processor will be used with a ground based telescope next year for a survey of several hundred selected stars for narrow band CO2 laser signals at 30 THz.

  9. Infrared Radiative Properties of Food Materials

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Precisely, infrared radiation is electromagnetic radiation whose wavelength is longer than that of visible light, but shorter than that of terahertz radiation and microwaves. The infrared portion of the electromagnetic spectrum spans roughly three orders of magnitude (750 nm to 100 µm) and has been...

  10. Strong-field physics with mid-infrared lasers

    NASA Astrophysics Data System (ADS)

    Pogorelsky, I. V.

    2002-04-01

    Mid-infrared gas laser technology promises to become a unique tool for research in strong-field relativistic physics. The degree to which physics is relativistic is determined by a ponderomotive potential. At a given intensity, a 10 μm wavelength CO2 laser reaches a 100 times higher ponderomotive potential than the 1 μm wavelength solid state lasers. Thus, we can expect a proportional increase in the throughput of such processes as laser acceleration, x-ray production, etc. These arguments have been confirmed in proof-of-principle Thomson scattering and laser acceleration experiments conducted at BNL and UCLA where the first terawatt-class CO2 lasers are in operation. Further more, proposals for the 100 TW, 100 fs CO2 lasers based on frequency-chirped pulse amplification have been conceived. Such lasers can produce physical effects equivalent to a hypothetical multi-petawatt solid state laser. Ultra-fast mid-infrared lasers will open new routes to the next generation electron and ion accelerators, ultra-bright monochromatic femtosecond x-ray and gamma sources, allow to attempt the study of Hawking-Unruh radiation, and explore relativistic aspects of laser-matter interactions. We review the present status and experiments with terawatt-class CO2 lasers, sub-petawatt projects, and prospective applications in strong-field science. .

  11. Laser radiation bracket debonding

    NASA Astrophysics Data System (ADS)

    Dostálová, Tat'jana; Jelínková, Helena; Šulc, Jan; Koranda, Petr; Nemec, Michal; Racek, Jaroslav; Miyagi, Mitsunobu

    2008-02-01

    Ceramic brackets are an aesthetic substitute for conventional stainless steel brackets in orthodontic patients. However, ceramic brackets are more brittle and have higher bond strengths, which can lead to bracket breakage and enamel damage during classical type of debonding. This study examined the possibility of laser radiation ceramic brackets removing as well as the possible damage of a surface structure of hard dental tissue after this procedure. Two types of lasers were used for the experiments - a laser diode LIMO HLU20F400 generating a wavelength of 808 nm with the maximum output power 20W at the end of the fiber (core diameter 400 μm, numerical aperture 0.22). As a second source, a diode-pumped Tm:YAP laser system generating a wavelength of 1.9 μm, with up to 3.8 W maximum output power was chosen. For the investigation, extracted incisors with ceramic brackets were used. In both cases, laser radiation was applied for 0.5 minute at a maximum power of 1 W. Temperature changes of the irradiated tissue was registered by camera Electrophysics PV320. After the interaction experiment, the photo-documentation was prepared by the stereomicroscope Nikon SMZ 2T, Japan. The surface tissue analysis was processed in "low vacuum" (30 Pa) regime without desiccation. This technique was used to record back-scattered electron images. Selecting the appropriate laser, resin, and bracket combination can minimize risks of enamel degradation and make debonding more safe.

  12. Subsurface optical stimulation of the rat prostate nerves using continuous-wave near-infrared laser radiation

    NASA Astrophysics Data System (ADS)

    Tozburun, Serhat; Lagoda, Gwen A.; Burnett, Arthur L.; Fried, Nathaniel M.

    2012-02-01

    Successful identification and preservation of the cavernous nerves (CN), which are responsible for sexual function, during prostate cancer surgery, will require subsurface detection of the CN beneath a thin fascia layer. This study explores optical nerve stimulation (ONS) in the rat with a fascia layer placed over the CN. Two near-IR diode lasers (1455 nm and 1550 nm lasers) were used to stimulate the CN in CW mode with a 1-mm-diameter spot in 8 rats. The 1455 nm wavelength provides an optical penetration depth (OPD) of ~350 μm, while 1550 nm provides an OPD of ~1000 μm (~3 times deeper than 1455 nm and 1870 nm wavelengths previously tested). Fascia layers with thicknesses of 85 - 600 μm were placed over the CN. Successful ONS was confirmed by an intracavernous pressure (ICP) response in the rat penis at 1455 nm through fascia 110 μm thick and at 1550 nm through fascia 450 μm thick. Higher incident laser power was necessary and weaker and slower ICP responses were observed as fascia thickness was increased. Subsurface ONS of the rat CN at a depth of 450 μm using a 1550 nm laser is feasible.

  13. Models for infrared atmospheric radiation

    NASA Technical Reports Server (NTRS)

    Tiwari, S. N.

    1976-01-01

    Line and band models for infrared spectral absorption are discussed. Radiative transmittance and integrated absorptance of Lorentz, Doppler, and voigt line profiles were compared for a range of parameters. It was found that, for the intermediate path lengths, the combined Lorentz-Doppler (Voigt) profile is essential in calculating the atmospheric transmittance. Narrow band model relations for absorptance were used to develop exact formulations for total absorption by four wide band models. Several continuous correlations for the absorption of a wide band model were compared with the numerical solutions of the wide band models. By employing the line-by-line and quasi-random band model formulations, computational procedures were developed for evaluating transmittance and upwelling atmospheric radiance. Homogeneous path transmittances were calculated for selected bands of CO, CO2, and N2O and compared with experimental measurements. The upwelling radiance and signal change in the wave number interval of the CO fundamental band were also calculated.

  14. Ultra-broadband hybrid infrared laser system

    NASA Astrophysics Data System (ADS)

    Budilova, O. V.; Ionin, A. A.; Kinyaevskiy, I. O.; Klimachev, Yu. M.; Kotkov, A. A.; Kozlov, A. Yu.

    2016-03-01

    A hybrid IR laser system consisting of molecular gas lasers with frequency conversion of laser radiation in a solid-state converter (nonlinear crystal) was developed. One of these gas lasers is a carbon monoxide laser operating in multi-line or single-line mode. Another one is a carbon dioxide laser operating in multi-line mode. The two lasers operate under Q-switching with a joint rotating mirror. Due to sum- and difference-frequency generation in nonlinear crystals, the laser system emits within wavelength range from 2.5 to 16.6 μm. The laser system emitting radiation over such an extremely wide wavelength range (2.7 octaves) is of interest for remote sensing and other applications connected with laser beam propagation in the atmosphere.

  15. Experimental characterization of the saturating, near infrared, self-amplified spontaneous emission free electron laser: Analysis of radiation properties and electron beam dynamics

    NASA Astrophysics Data System (ADS)

    Murokh, Alex

    2002-01-01

    In this work, the main results of the VISA experiment (Visible to Infrared SASE Amplifier) are presented and analyzed. The purpose of the experiment was to build a state-of-the-art single pass self-amplified spontaneous emission (SASE) free electron laser (FEL) based on a high brightness electron beam, and characterize its operation, including saturation, in the near infrared spectral region. This experiment was hosted by Accelerator Test Facility (ATF) at Brookhaven National Laboratory, which is a users facility that provides high brightness relativistic electron beams generated with the photoinjector. During the experiment, SASE FEL performance was studied in two regimes: a long bunch, lower gain operation; and a short bunch high gain regime. The transition between the two conditions was possible due to a novel bunch compression mechanism, which was discovered in the course of the experiment. This compression allowed the variation of peak current in the electron beam before it was launched into the 4-m VISA undulator. In the long bunch regime, a SASE FEL power gain length of 29 cm was obtained, and the generated radiation spectral and statistical properties were characterized. In the short bunch regime, a power gain length of under 18 cm was achieved at 842 nm, which is at least a factor of two shorter than ever previously achieved in this spectral range. Further, FEL saturation was obtained before the undulator exit. The FEL system's performance was measured along the length of the VISA undulator, and in the final state. Statistical, spectral and angular properties of the short bunch SASE radiation have been measured in the exponential gain regime, and at saturation. One of the most important aspects of the data analysis presented in this thesis was the development and use of start-to-end numerical simulations of the experiment. The dynamics of the ATF electron beam was modeled starting from the photocathode, through acceleration, transport, and inside the VISA

  16. MIDIR (Mid-Infrared) laser, phase 1

    NASA Astrophysics Data System (ADS)

    Tanimoto, Douglas; Jeffers, William; Shellan, Jeffrey

    1988-04-01

    Advances in sensor technology have led to a proliferation of electro-optical systems operating in the mid-infrared (3 to 5 micron). Examples are search and track sets, missile seekers, laser designators, and high energy lasers. To counter enemy use of such systems, jamming and collecting systems which employ lasers of modest power operating within the spectral pass-band of the threat are required. A modulated, wavelength agile, compact, mid-infrared laser of moderate average output powers is extremely attractive for infrared countermeasures and OPTINT collections applications. A unique electric discharge gain generator design has been investigated which promises significant improvements in efficiency, compactness and reliability for pulsed gas laser systems with high peak power and moderate average power outputs.

  17. Solar and Infrared Radiation Station (SIRS) Handbook

    SciTech Connect

    Stoffel, T

    2005-07-01

    The Solar Infrared Radiation Station (SIRS) provides continuous measurements of broadband shortwave (solar) and longwave (atmospheric or infrared) irradiances for downwelling and upwelling components. The following six irradiance measurements are collected from a network of stations to help determine the total radiative flux exchange within the Atmospheric Radiation Measurement (ARM) Southern Great Plains (SGP) Climate Research Facility: • Direct normal shortwave (solar beam) • Diffuse horizontal shortwave (sky) • Global horizontal shortwave (total hemispheric) • Upwelling shortwave (reflected) • Downwelling longwave (atmospheric infrared) • Upwelling longwave (surface infrared)

  18. Generating Far-Infrared Radiation By Two-Wave Mixing

    NASA Technical Reports Server (NTRS)

    Borenstain, Shmuel

    1992-01-01

    Far-infrared radiation 1 to 6 GHz generated by two-wave mixing in asymmetrically grown GaAs/AlxGa1-xAs multiple-quantum-well devices. Two near-infrared semiconductor diode lasers phase-locked. Outputs amplified, then combined in semiconductor nonlinear multiple-quantum-well planar waveguide. Necessary to optimize design of device with respect to three factors: high degree of confinement of electromagnetic field in nonlinear medium to maximize power density, phase matching to extend length of zone of interaction between laser beams in non-linear medium, and nonlinear susceptibility. Devices used as tunable local oscillators in heterodyne-detection radiometers.

  19. Stimulated radiative laser cooling

    NASA Astrophysics Data System (ADS)

    Muys, P.

    2008-04-01

    Building a refrigerator based on the conversion of heat into optical energy is an ongoing engineering challenge. Under well-defined conditions, spontaneous anti-Stokes fluorescence of a dopant material in a host matrix is capable of lowering the host temperature. The fluorescence is conveying away a part of the thermal energy stored in the vibrational oscillations of the host lattice. In particular, applying this principle to the cooling of (solid-state) lasers opens up many potential device applications, especially in the domain of high-power lasers. In this paper, an alternative optical cooling scheme is outlined, leading to the radiative cooling of solid-state lasers. It is based on converting the thermal energy stored in the host into optical energy by means of a stimulated nonlinear process, rather than a spontaneous process. This should lead to better cooling efficiencies and a higher potential of applying the principle for device applications.

  20. Infrared Laser Spectroscopy, 1980-1983

    NASA Astrophysics Data System (ADS)

    McDowell, Robin S.

    1983-11-01

    The text for the Short Course on Infrared Laser Spectroscopy given at the Los Alamos Conference on Optics '83 is R. S. McDowell, "Vibrational Spectroscopy Using Tunable Lasers," in Vibrational Spectra and Structure, J. R. Durig, ed. (Elsevier, Amsterdam, 1981) 10, 1-151, which includes references through 1979. The present paper summarizes progress in this field from 1980 to early 1983.

  1. Infrared laser stimulation of retinal and vestibular neurons

    NASA Astrophysics Data System (ADS)

    Bardin, Fabrice; Bec, Jean-Michel; Albert, Emmanuelle S.; Hamel, Christian; Dupeyron, Gérard; Chabbert, Christian; Marc, Isabelle; Dumas, Michel

    2011-03-01

    The study of laser-neuron interaction has gained interest over the last few years not only for understanding of fundamental mechanisms but also for medical applications such as prosthesis because of the non-invasive characteristic of the laser stimulation. Several authors have shown that near infrared lasers are able to stimulate neurons. It is suggested that a thermal gradient induced by the absorption of the laser radiation on cells is the primary effect but the exact mechanism remains unclear. We show in this work that infrared laser radiations provide a possible way for stimulating retinal and vestibular ganglion cells. We describe relevant physical characteristics allowing safe and reproducible neuron stimulations by single infrared pulses. Calcium fluorescence imaging and electrophysiological recordings have been used to measure ionic exchanges at the neuron membrane. The stimulation system is based on a pulsed laser diode beam of a few mW. Effects of three different wavelengths (from 1470 to 1875 nm) and stimulation durations have been investigated. Variations of the stimulation energy thresholds suggest that the main physical parameter is the water optical absorption. Measurements of the temperature at the cell membrane show that a constant temperature rise is required to stimulate neurons, suggesting a photothermal process.

  2. Infrared laser diode with visible illuminator for biomedical stimulation

    NASA Astrophysics Data System (ADS)

    Strek, Wieslaw; Podbielska, Halina; Szafranski, C.; Kuzmin, Andrei N.; Ges, J. A.; Ryabtsev, Gennadii I.

    1995-02-01

    The special laser diode device (LDD) leasing in the near infrared region (IR) with two wavelengths: (lambda) 1 equals 850 nm and (lambda) 2 equals 1000 nm, designed for laser therapy, is presented. This device is characterized by a unique feature, namely a separate built-in illuminator, operating in 670 nm. The special construction of LDD and the illuminator enables the user to visualize exactly the surface irradiated by IR radiation. The exposure time and the output of laser power are also controlled and can be displayed on the LED monitor at the front panel. This new device, described here, is compact, low cost, and user friendly.

  3. Infrared Laser Generation Of Heterogeneous Catalysts And Laser-Induced Reactions At Catalytic Surfaces

    NASA Astrophysics Data System (ADS)

    Danen, Wayne C.; Cheng, , Sheng-San; Iyer, Pradeep K.; Chiou, Shane-Jaw

    1984-05-01

    It has been demonstrated that continuous wave infrared CO2 laser radiation can be util-ized to rapidly produce active catalysts from inert precursors. The activity and selectiv-ity of Ca0 produced from Ca(OH)2 for the isomerization of 1-butene to cis- and trans-2-but-ene is discussed. Variation of the laser irradiation time produces catalytic activity and selectivity qualitatively similar to that resulting from conventional calcination at different temperatures. Pulsed infrared laser-induced reactions at catalytic surfaces are also discussed with emphasis on the dehydrobromination of 2-bromopropane and ethylene elimination from glycine ethyl ester hydrochloride at BaSO4 , A1PO4, and similar surfaces. Correlations are made of the extent of reaction with various experimental parameters including nature of the catalyst, laser frequency, laser fluence, number of laser pulses, and reagent-catalyst ratio.

  4. Characterizing Far-infrared Laser Emissions and the Measurement of Their Frequencies.

    PubMed

    Jackson, Michael; Zink, Lyndon R

    2015-01-01

    The generation and subsequent measurement of far-infrared radiation has found numerous applications in high-resolution spectroscopy, radio astronomy, and Terahertz imaging. For about 45 years, the generation of coherent, far-infrared radiation has been accomplished using the optically pumped molecular laser. Once far-infrared laser radiation is detected, the frequencies of these laser emissions are measured using a three-laser heterodyne technique. With this technique, the unknown frequency from the optically pumped molecular laser is mixed with the difference frequency between two stabilized, infrared reference frequencies. These reference frequencies are generated by independent carbon dioxide lasers, each stabilized using the fluorescence signal from an external, low pressure reference cell. The resulting beat between the known and unknown laser frequencies is monitored by a metal-insulator-metal point contact diode detector whose output is observed on a spectrum analyzer. The beat frequency between these laser emissions is subsequently measured and combined with the known reference frequencies to extrapolate the unknown far-infrared laser frequency. The resulting one-sigma fractional uncertainty for laser frequencies measured with this technique is ± 5 parts in 10(7). Accurately determining the frequency of far-infrared laser emissions is critical as they are often used as a reference for other measurements, as in the high-resolution spectroscopic investigations of free radicals using laser magnetic resonance. As part of this investigation, difluoromethane, CH2F2, was used as the far-infrared laser medium. In all, eight far-infrared laser frequencies were measured for the first time with frequencies ranging from 0.359 to 1.273 THz. Three of these laser emissions were discovered during this investigation and are reported with their optimal operating pressure, polarization with respect to the CO2 pump laser, and strength. PMID:26709957

  5. Novel materials as potential infrared laser hosts

    NASA Astrophysics Data System (ADS)

    Sarkies, Julian Richard

    The work presented in this thesis has concentrated on an assessment and characterisation of potential laser host media which will only support low phonon or vibrational modes. This is a necessary criterion if systems in which the active ions are lanthanides are to be made to lase in the mid-infrared, as in conventional host media non- radiative processes dominate transitions in this region. Research has concentrated upon two main areas. Firstly a spectroscopic study of lanthanide doped PBr3/AlBr3/SbBr3 was undertaken. A detailed investigation and characterisation of the stable solution formation region was carried out. The doping levels achievable were seen to vary across the lanthanide series from a maximum 0.24mol% for praesodymium to a minimum 0.15mol% for ytterbium. Energies of the characteristic 4 f absorptions of the trivalent lanthanides were measured, along with their oscillator strengths. Judd-Ofelt parameters were found for several rare earths. Stimulated emission cross sections were found to be higher than in conventional glass hosts for certain transitions, such as 6.83 × 10 -20 cm2 for the 4F3/2 --> 4I11/2 transition in the Nd3+ doped liquid. This was verified both experimentally and by the Ladenburg-Fuchtbauer relation when compared to a standard silicate glass. The behaviour, both spectroscopic and physical, of the doped solutions was seen to change dramatically upon heating. Heating the solutions gave rise to higher crystallisation rates, but lower non-radiative relaxation rates. Waveguide and laser experiments were attempted in both bulk and capillary geometries, however material factors such as crystallisation and thermal lensing prevented laser action. Secondly, rare earth doped planar waveguides of zinc sulphide were prepared. A full characterisation of the way in which waveguide loss was affected by factors such as deposition rate, doping level and waveguide masking during evaporation was performed. Waveguide losses as low as 1.5dB/cm at 980nm

  6. Mid-infrared Laser System Development for Dielectric Laser Accelerators

    NASA Astrophysics Data System (ADS)

    Jovanovic, Igor; Xu, Guibao; Wandel, Scott

    Laser-driven particle accelerators based on dielectric laser acceleration are under development and exhibit unique and challenging pump requirements. Operation in the mid-infrared (5 μm) range with short pulses (<1 ps FWHM), high pulse energy (>500 μJ) and good beam quality is required. We present our progress on the design and development of a novel two- stage source of mid-infrared pulses for this application, which is based on optical parametric amplification. Beta barium borate and zinc germanium phosphide crystals are used, and are pumped by a Ti:sapphire ultrashort laser and seeded by self-phase modulation and parametric generation-based sources.

  7. Mid-infrared solid-state lasers and laser materials

    NASA Technical Reports Server (NTRS)

    Barnes, Norman P.; Byvik, Charles E.

    1988-01-01

    An account is given of NASA-Langley's objectives for the development of advanced lasers and laser materials systems applicable to remote sensing in the mid-IR range. Prominent among current concerns are fiber-optic spectroscopy, eye-safe solid-state lasers for both Doppler sensing and mid-IR wavelength-generation laser pumping, and nonlinear optics generating tunable mid-IR radiation. Ho:YAG lasers are noted to exhibit intrinsic advantages for the desired applications, and are pumpable by GaAlAs laser diodes with a quantum efficiency approaching 2.

  8. Infrared Absorption Spectroscopy Measurement of SOx using Tunable Infrared Laser

    NASA Astrophysics Data System (ADS)

    Fukuchi, Tetsuo

    The absorption characteristics of sulfur dioxide (SO2) and sulfur trioxide (SO3) in the infrared region were measured using a quantum cascade laser and an absorption cell of length 1 m heated to 150°C. The laser was scanned over the wavelength range 6.9-7.4 μm, which included the absorption bands of SO2 and SO3. Measurement results showed that the absorption bands of SO2 and SO3 partially overlapped, with peaks at 7.28 μm and 7.35 μm for SO2 and 7.14 μm and 7.25 μm for SO3. These results showed the possbility of using infrared laser absorption spectroscopy for measurement of sulfur oxides (SOx) in flue gas. For SO3 measurement, infrared absorption spectroscopy was shown to be more suitable than ultraviolet absorption spectroscopy. The absorption characteristics of open air in the same wavelength region showed that the interference due to water vapor must be efficiently removed to perform SOx measurement in flue gas.

  9. Improved source of infrared radiation for spectroscopy

    NASA Technical Reports Server (NTRS)

    Burkhard, D. G.; Rao, K. N.

    1971-01-01

    Radiation from a crimped V-groove in the electrically heated metallic element of a high-resolution infrared spectrometer is more intense than that from plane areas adjacent to the element. Radiation from the vee and the flat was compared by alternately focusing on the entrance slit of a spectrograph.

  10. Infrared absorption of fs-laser textured CVD diamond

    NASA Astrophysics Data System (ADS)

    Calvani, P.; Bellucci, A.; Girolami, M.; Orlando, S.; Valentini, V.; Polini, R.; Mezzetti, A.; Di Fonzo, F.; Trucchi, D. M.

    2016-03-01

    Nanoscale periodic texturing on polycrystalline CVD diamond surface was performed to obtain a significant increase in optical absorptance to visible and near-infrared radiation. Surface texturing, obtained by the use of fs-laser ultrashort pulses, has been demonstrated to induce a controlled periodicity of ripples of about 170 nm and length of several µm, able to drastically increase the diamond capability of interacting with solar radiation from its intrinsic visible blindness. Ultraviolet and visible Raman spectroscopy has been used to confirm the absence of non-diamond phases resulting from the process for the fs-laser-textured sample. Moreover, here we investigate the optical properties in the range 200 nm-25 µm. Absorbance of fs-laser-textured CVD diamond is considerably higher than the untreated one at every wavelength, resulting in a remarkable increase in the emittance: It points out the need for an optimization of process parameters to enhance the selective absorption capability.

  11. Two color far infrared laser interferometer

    SciTech Connect

    Kawahata, K.; Akiyama, T.; Pavlichenko, R.; Tanaka, K.; Tokuzawa, T.; Ito, Y.; Okajima, S.; Nakayama, K.; Wood, K.

    2006-10-15

    Two color interferometer using a short wavelength far infrared laser has been developed for high performance plasmas on large helical device and for future fusion devices such as ITER. High power laser lines simultaneously oscillating at 57.2 and 47.6 {mu}m were achieved in a CO{sub 2}-laser-pumped CH{sub 3}OD laser. By introducing Ge:Ga photoconductive detectors operating at liquid He temperature, we have successfully detected two color beat signals (0.55 and 1.2 MHz) with excellent signal-to-noise ratio ({approx}40 dB). These beat signals were fed into phase comparators for phase measurement after passing through intermediate frequency bandpass filters. Two color far infraned laser interferometer work was successful in the demonstration of mechanical vibration compensation.

  12. Low Level Laser Therapy: laser radiation absorption in biological tissues

    NASA Astrophysics Data System (ADS)

    Di Giacomo, Paola; Orlando, Stefano; Dell'Ariccia, Marco; Brandimarte, Bruno

    2013-07-01

    In this paper we report the results of an experimental study in which we have measured the transmitted laser radiation through dead biological tissues of various animals (chicken, adult and young bovine, pig) in order to evaluate the maximum thickness through which the power density could still produce a reparative cellular effect. In our experiments we have utilized a pulsed laser IRL1 ISO model (based on an infrared diode GaAs, λ=904 nm) produced by BIOMEDICA s.r.l. commonly used in Low Level Laser Therapy. Some of the laser characteristics have been accurately studied and reported in this paper. The transmission results suggest that even with tissue thicknesses of several centimeters the power density is still sufficient to produce a cell reparative effect.

  13. Infrared laser spectroscopic trace gas sensing

    NASA Astrophysics Data System (ADS)

    Sigrist, Markus

    2016-04-01

    Chemical sensing and analyses of gas samples by laser spectroscopic methods are attractive owing to several advantages such as high sensitivity and specificity, large dynamic range, multi-component capability, and lack of pretreatment or preconcentration procedures. The preferred wavelength range comprises the fundamental molecular absorption range in the mid-infared between 3 and 15 μm, whereas the near-infrared range covers the (10-100 times weaker) higher harmonics and combination bands. The availability of near-infrared and, particularly, of broadly tunable mid-infrared sources like external cavity quantum cascade lasers (EC-QCLs), interband cascade lasers (ICLs), difference frequency generation (DFG), optical parametric oscillators (OPOs), recent developments of diode-pumped lead salt semiconductor lasers, of supercontinuum sources or of frequency combs have eased the implementation of laser-based sensing devices. Sensitive techniques for molecular absorption measurements include multipass absorption, various configurations of cavity-enhanced techniques such as cavity ringdown (CRD), or of photoacoustic spectroscopy (PAS) including quartz-enhanced (QEPAS) or cantilever-enhanced (CEPAS) techniques. The application requirements finally determine the optimum selection of laser source and detection scheme. In this tutorial talk I shall discuss the basic principles, present various experimental setups and illustrate the performance of selected systems for chemical sensing of selected key atmospheric species. Applications include an early example of continuous vehicle emission measurements with a mobile CO2-laser PAS system [1]. The fast analysis of C1-C4 alkanes at sub-ppm concentrations in gas mixtures is of great interest for the petrochemical industry and was recently achieved with a new type of mid-infrared diode-pumped piezoelectrically tuned lead salt vertical external cavity surface emitting laser (VECSEL) [2]. Another example concerns measurements on short

  14. Transition undulator radiation as bright infrared sources

    SciTech Connect

    Kim, K.J.

    1995-02-01

    Undulator radiation contains, in addition to the usual component with narrow spectral features, a broad-band component in the low frequency region emitted in the near forward direction, peaked at an angle 1/{gamma}, where {gamma} is the relativistic factor. This component is referred to as the transition undulator radiation, as it is caused by the sudden change in the electron`s longitudinal velocity as it enters and leaves the undulator. The characteristic of the transition undulator radiation are analyzed and compared with the infrared radiation from the usual undulator harmonics and from bending magnets.

  15. Porcine skin damage thresholds for 0.6 to 9.5 cm beam diameters from 1070-nm continuous-wave infrared laser radiation.

    PubMed

    Vincelette, Rebecca; Noojin, Gary D; Harbert, Corey A; Schuster, Kurt J; Shingledecker, Aurora D; Stolarski, Dave; Kumru, Semih S; Oliver, Jeffrey W

    2014-03-01

    There is an increasing use of high-power fiber lasers in manufacturing and telecommunications industries operating in the infrared spectrum between 1000 and 2000 nm, which are advertised to provide as much as 10 kW continuous output power at 1070 nm. Safety standards have traditionally been based on experimental and modeling investigations with scant data available for these wavelengths. A series of studies using 1070-nm infrared lasers to determine the minimum visible lesion damage thresholds in skin using the Yucatan miniature pig (Sus scrofa domestica) for a range of beam diameters (0.6, 1.1, 1.9, 2.4, 4.7, and 9.5 cm) and a range of exposure durations (10 ms to 10 s) is presented. Experimental peak temperatures associated with each damage threshold were measured using thermal imaging. Peak temperatures at damage threshold for the 10-s exposures were ∼10°C lower than those at shorter exposures. The lowest and highest experimental minimum visible lesion damage thresholds were found to have peak radiant exposures of 19 and 432  J/cm2 for the beam diameter-exposure duration pairs of 2.4 cm, 25 ms and 0.6 cm, 10 s, respectively. Thresholds for beam diameters >2.5  cm had a weak to no effect on threshold radiant exposure levels for exposure times ≤0.25  s, but may have a larger effect on thresholds for exposures ≥10  s. PMID:24658776

  16. Use of powerful infrared pulsed Nd-YAG laser for treating osteogenic sarcoma

    NASA Astrophysics Data System (ADS)

    Biser, Vladimir A.; Kaplan, Michael A.; Kursova, Larisa V.; Neborak, Yuri T.

    1996-01-01

    Powerful infra-red laser radiation may induce necrosis of a malignant tumor located in a human bone without destructing skin cover. A superficial irradiation of the osteogenic sarcoma with an Nd-YAG laser (pulse power no less than 10 MW, average power 100 - 300 mW, time of exposure 10 - 90 min) has resulted in a severe damage of the tumor (more than 90% of the tumor mass) in 57% of cases. A combined laser/gamma irradiation showed a severe damage in 83% of cases. The results obtained suggest that laser radiation with the above parameters combined with gamma radiation may be used in treatment of osteogenic sarcoma.

  17. Oxide glasses for mid-infrared lasers

    NASA Astrophysics Data System (ADS)

    Richards, Billy D. O.; Jha, Animesh; Jose, Gin; Jiang, Xin

    2011-06-01

    We present an overview of rare-earth doped heavy metal oxide and oxy-fluoride glasses which show promise as host materials for lasers operating in the 2-5 μm spectral region for medical, military and sensing applications. By engineering glass composition and purity, tellurite and germanate glasses can support transmission up to and beyond 5 μm and can have favourable thermal, mechanical and environmental stability compared to fluoride glasses. We discuss techniques for glass purification and water removal for enhanced infrared transmission. By comparing the material properties of the glass, and spectroscopic performance of selected rare-earth dopant ions we can identify promising compositions for fibre and bulk lasers in the mid-infrared. Tellurite glass has recently been demonstrated to be a suitable host material for efficient and compact lasers in the {2 μm spectral region in fibre and bulk form and the next challenge is to extend the operating range further into the infrared region where silica fibre is not sufficiently transparent, and provide an alternative to fluoride glass and fibre.

  18. Lageos orbit decay due to infrared radiation from Earth

    NASA Technical Reports Server (NTRS)

    Rubincam, David Parry

    1987-01-01

    Infrared radiation from the Earth may be the principal reason for the decay of Lageos' orbit. The radiation heats up the laser retroreflectors embedded in Lageos' aluminum surface. This creates a north-south temperature gradient on the satellite. The gradient in turn causes a force to be exerted on Lageos because of recoil from photons leaving its surface. The delayed heating of the retroreflectors due to their thermal inertia gives the force a net along-track component which always acts like drag. A simple thermal model for the retroreflectors indicates that this thermal drag accounts for about half the observed average along-track acceleration of -3.3 x 10 to the -10 power m/sec squared. The contribution from the aluminum surface to this effect is negligible. The infrared effect cannot explain the large observed fluctuations in drag which occur mainly when the orbit intersects the Earth's shadow.

  19. Lageos orbit decay due to infrared radiation from earth

    NASA Technical Reports Server (NTRS)

    Rubincam, David Parry

    1987-01-01

    Infrared radiation from the earth may be the principal reason for the decay of Lageos' orbit. The radiation heats up the laser retroreflectors embedded in Lageos' aluminum surface. This creates a north-south temperature gradient on the satellite. The gradient in turn causes a force to be exerted on Lageos because of recoil from photons leaving its surface. The delayed heating of the retroreflectors due to their thermal inertia gives the force a net along-track component which always acts like drag. A simple thermal model for the retroreflectors indicates that this thermal drag accounts for about half the observed average along-track acceleration of -3.3 x 10 to the -10th power m/sec squared. The contribution from the aluminum surface to this effect is negligible. The infrared effect cannot explain the large observed fluctuations in drag which occur mainly when the orbit intersects the earth's shadow.

  20. Electro-optic detection of continuous-wave mid-infrared radiation

    NASA Astrophysics Data System (ADS)

    Cao, Hua; Nahata, Ajay

    2002-10-01

    We demonstrate coherent detection of continuous-wave mid-infrared radiation. This radiation is produced by use of conventional difference-frequency mixing and detected via the linear electro-optic effect. The detection process allows for the simultaneous measurement of the amplitude and phase properties of the infrared field. Both processes require an amplitude-modulated optical beam that is derived from the superimposed output of two single-frequency lasers. With appropriate choice of lasers and nonlinear optical crystals, the technique may be applied to any wavelength throughout the far and mid infrared.

  1. Mid-Infrared Laser Orbital Septal Tightening

    PubMed Central

    Chu, Eugene A.; Li, Michael; Lazarow, Frances B.; Wong, Brian J. F.

    2014-01-01

    IMPORTANCE Blepharoplasty is one of the most commonly performed facial aesthetic surgeries. While myriad techniques exist to improve the appearance of the lower eyelids, there is no clear consensus on the optimal management of the orbital septum. OBJECTIVES To evaluate the safety and feasibility of the use of the holmium:yttrium aluminum garnet (Ho:YAG) laser for orbital septal tightening, and to determine whether modest use of this laser would provide some degree of clinical efficacy. DESIGN, SETTING, AND PARTICIPANTS Direct laser irradiation of ex vivo bovine tissue was used to determine appropriate laser dosimetry using infrared thermal imaging and optical coherence tomography before conducting a pilot clinical study in 5 patients. Laser irradiation of the lower eyelid orbital septum was performed through a transconjunctival approach. Standardized preoperative and postoperative photographs were taken for each patient and evaluated by 6 unbiased aesthetic surgeons. EXPOSURE Use of the Ho:YAG laser for orbital septal tightening. MAIN OUTCOME AND MEASURE To determine appropriate laser dosimetry, infrared thermal imaging and optical coherence tomography were used to monitor temperature and tissue shape changes of ex vivo bovine tissue that was subjected to direct laser irradiation. For the clinical study, preoperative and postoperative photographs were evaluated by 6 surgeons on a 10-point Likert scale. RESULTS Optical coherence tomography demonstrated that laser irradiation of bovine tissue to a temperature range of 60°C to 80°C resulted in an increase in thickness of up to 2-fold. There were no complications or adverse cosmetic outcomes in the patient study. Patient satisfaction with the results of surgery averaged 7 on a 10-point Likert scale. For 3 patients, 3 (50%) of the evaluators believed there was a mild improvement in appearance of the lower eyelids after surgery. The remaining patients were thought to have no significant changes. CONCLUSIONS AND

  2. Ultraviolet radiation induced discharge laser

    DOEpatents

    Gilson, Verle A.; Schriever, Richard L.; Shearer, James W.

    1978-01-01

    An ultraviolet radiation source associated with a suitable cathode-anode electrode structure, disposed in a gas-filled cavity of a high pressure pulsed laser, such as a transverse electric atmosphere (TEA) laser, to achieve free electron production in the gas by photoelectric interaction between ultraviolet radiation and the cathode prior to the gas-exciting cathode-to-anode electrical discharge, thereby providing volume ionization of the gas. The ultraviolet radiation is produced by a light source or by a spark discharge.

  3. A tunable mid-infrared laser source for remote sensing

    NASA Technical Reports Server (NTRS)

    Barnes, Norman P.

    1991-01-01

    Many remote sensing needs can be effectively addressed with a tunable laser source in the mid infrared. One potential laser source is an optical parametric oscillator and amplifier system pumped by a near infrared solid state laser. Advantages of such a system and progress made at NASA Langley Research Center to date on such a system are described.

  4. Mid - infrared solid state lasers for spectroscopic applications

    NASA Astrophysics Data System (ADS)

    Terekhov, Yuri

    This work is devoted to study of novel high power middle-infrared (Mid-IR) laser sources enabling development of portable platform for sensing of organic molecules with the use of recently discovered Quartz Enhanced Photo Acoustic Spectroscopy (QEPAS). The ability to detect small concentrations is beneficial to monitor atmosphere pollution as well for biomedical applications such as analysis of human breath to detect earlier stages of cancer or virus activities. A QEPAS technique using a quartz tuning fork (QTF) as a detector enables a strong enhancement of measured signal when pump laser is modulated with a frequency coinciding with a natural frequency of a QTF. It is known that the detectability of acousto-optics based sensors is proportional to the square root of the laser intensity used for detection of analyte. That is the reason why commercially available semiconductor Mid-IR lasers having small output power limit sensitivity of modern QEPAS based sensors. The lack of high power broadly tunable lasers operating with a modulation frequency of quartz forks (~ 32.768 kHz) is the major motivation of this study. Commercially available Mid-IR (2-3.3 microm), single frequency, continuous wave (CW) fiber pumped lasers based on transition metal doped chalcogenides (e.g. Cr:ZnSe) prove to be efficient laser sources for organic molecules detection. However, their direct modulation is limited to several kHz, and cannot be directly used in combination with QEPAS. Hence, one objective of this work is to study and develop fiber laser pumped Ho:YAG (Er:YAG)/Cr:ZnSe tandem laser system/s. Ho (Holmium) and/or Er (Erbium) ions having long radiation lifetime (~ 10 ms) can effectively accumulate population inversion under CW fiber laser excitation. Utilization of acousto-optic (AO) modulators in the cavity of Ho:YAG (Er:YAG) laser will enable effective Q-Switching with repetition rate easily reaching the resonance frequency of a QTF. It is expected that utilization of Ho:YAG (Er

  5. Infrared microspectroscopy with synchrotron radiation

    SciTech Connect

    Carr, G.L.; Williams, G.P.

    1997-09-01

    Infrared microspectroscopy with a high brightness synchrotron source can achieve a spatial resolution approaching the diffraction limit. However, in order to realize this intrinsic source brightness at the specimen location, some care must be taken in designing the optical system. Also, when operating in diffraction limited conditions, the effective spatial resolution is no longer controlled by the apertures typically used for a conventional (geometrically defined) measurement. Instead, the spatial resolution depends on the wavelength of light and the effective apertures of the microscope`s Schwarzchild objectives. The authors have modeled the optical system from the synchrotron source up to the sample location and determined the diffraction-limited spatial distribution of light. Effects due to the dependence of the synchrotron source`s numerical aperture on wavelength, as well as the difference between transmission and reflection measurement modes, are also addressed. Lastly, they examine the benefits (when using a high brightness source) of an extrinsic germanium photoconductive detector with cone optics as a replacement for the standard MCT detector.

  6. Tunable infrared laser sources and applications

    NASA Astrophysics Data System (ADS)

    Libatique, Nathaniel Joseph C.

    diode-pumped tunable mid-infrared (3 mum) fiber laser. (5) New electronically-controlled continuously wavelength-tunable near-infrared sources based on advanced electro-optic scanners fabricated from poled LiTaO3 crystals. (6) The development of continuously tunable electronically-controlled FBG-referenced near infrared sources suitable for trace gas spectroscopy.

  7. Study on laser and infrared attenuation performance of carbon nanotubes

    NASA Astrophysics Data System (ADS)

    Liu, Xiang-cui; Liu, Qing-hai; Dai, Meng-yan; Cheng, Xiang; Fang, Guo-feng; Zhang, Tong; Liu, Haifeng

    2014-11-01

    In recent years, the weapon systems of laser and infrared (IR) imaging guidance have been widely used in modern warfare because of their high precision and strong anti-interference. However, military smoke, a rapid and effective passive jamming method, can effectively counteract the attack of precision-guided weapons by their scattering and absorbing effects. The traditional smoke has good visible light (0.4-0.76μm) obscurant performance, but hardly any effects to other electromagnetic wave bands while the weapon systems of laser and IR imaging guidance usually work in broad band, including the near-infrared (1-3μm), middle-infrared (3-5μm), far-infrared (8-14μm), and so on. Accordingly, exploiting new effective obscurant materials has attracted tremendous interest worldwide nowadays. As is known, the nano-structured materials have lots of unique properties comparing with the traditional materials suggesting that they might be the perfect alternatives to solve the problems above. Carbon nanotubes (CNTs) are well-ordered, all-carbon hollow graphitic nano-structured materials with a high aspect ratio, lengths from several hundred nanometers to several millimeters. CNTs possess many unique intrinsic physical-chemical properties and are investigated in many areas reported by the previous studies. However, no application research about CNTs in smoke technology field is reported yet. In this paper, the attenuation performances of CNTs smoke to laser and IR were assessed in 20m3 smoke chamber. The testing wavebands employed in experiments are 1.06μm and 10.6μm laser, 3-5μm and 8-14μm IR radiation. The main parameters were obtained included the attenuation rate, transmission rate, mass extinction coefficient, etc. The experimental results suggest that CNTs smoke exhibits excellent attenuation ability to the broadband IR radiation. Their mass extinction coefficients are all above 1m2·g-1. Nevertheless, the mass extinction coefficients vary with the sampling time

  8. Near-infrared laser speckle imaging of human breast tissue

    NASA Astrophysics Data System (ADS)

    Bean, Robert Speer

    Current methods of breast cancer diagnostics (self-exam, clinical exam, x-ray mammography) fail to diagnose a significant number of cases while still in readily operable stages. This is especially true in younger women, where fibrotic tissue reduces the efficacy of x-ray mammography. Near infrared (NIR) laser photons pass diffusively through human tissue, creating a speckle pattern in a detector after transmission. The high and low intensity variations of the speckle have the appearance of random noise, but are not. The speckle pattern will have an intensity distribution that is informative about the scattering and absorption properties of the tissue that is imaged. Adaptations to the Los Alamos National Laboratory MCNP code are described that allow simulation of NIR laser transport through human tissue. A HeNe laser was used to create laser intensity patterns via transmission through homogeneous and non-homogeneous tissue phantoms. The Kolmogorov-Smirnov test was used to compare the cumulative distribution functions of the laser intensity patterns, and identify the presence of a non-homogeneity. Laser speckle techniques offer the ability to image tumors with few (<3) millimeter resolution without ionizing radiation dose.

  9. Infrared Pulse-laser Long-path Absorption Measurement of Carbon Dioxide Using a Raman-shifted Dye Laser

    NASA Technical Reports Server (NTRS)

    Minato, Atsushi; Sugimoto, Nobuo; Sasano, Yasuhiro

    1992-01-01

    A pulsed laser source is effective in infrared laser long-path absorption measurements when the optical path length is very long or the reflection from a hard target is utilized, because higher signal-to-noise ratio is obtained in the detection of weak return signals. We have investigated the performance of a pulse-laser long-path absorption system using a hydrogen Raman shifter and a tunable dye laser pumped by a Nd:YAG laser, which generates second Stokes radiation in the 2-micron region.

  10. Development of far infrared attenuation to measure electron densities in cw pin discharge lasers

    NASA Technical Reports Server (NTRS)

    Babcock, R. V.

    1977-01-01

    A two beam attenuation technique was devised to measure electron densities 10 to the 9th power to 10 to the 11th power cm/3 resolved to 1 cm, in a near atmospheric COFFEE laser discharge, using 496 micrometer and 1,220 micrometer radiations from CH3F, optically pumped by a CO2 laser. A far infrared generator was developed which was suitable except for a periodic intensity variation in FIR output deriving from frequency variation of the pump radiation.

  11. Estimating the Infrared Radiation Wavelength Emitted by a Remote Control Device Using a Digital Camera

    ERIC Educational Resources Information Center

    Catelli, Francisco; Giovannini, Odilon; Bolzan, Vicente Dall Agnol

    2011-01-01

    The interference fringes produced by a diffraction grating illuminated with radiation from a TV remote control and a red laser beam are, simultaneously, captured by a digital camera. Based on an image with two interference patterns, an estimate of the infrared radiation wavelength emitted by a TV remote control is made. (Contains 4 figures.)

  12. Explosive crystallization of PZT microstructures by femtosecond infrared radiation

    NASA Astrophysics Data System (ADS)

    Elshin, A. S.; Firsova, N. Yu; Emelianov, V. I.; Pronin, I. P.; Senkevich, S. V.; Zhigalina, O. M.; Mishina, E. D.; Sigov, A. S.

    2015-12-01

    The features of microstructure crystallization into perovskite phase in lead zirconate titanate film by femtosecond laser radiation of near-infrared range were discussed. In-situ crystallization kinetics by method of second harmonic generation (SHG) was studied. The presence of several types of crystallization was shown, including ultra-fast (explosive) crystallization occurring immediately after the start of exposure, and slow (self-sustaining) crystallization, occurring after termination of exposure. The advantage of the second-harmonic generation microscopy for the study of annealed microstructures was shown. The morphology of microstructures was investigated by transmission electron microscopy (TEM).

  13. Infrared radiation models for atmospheric methane

    NASA Technical Reports Server (NTRS)

    Cess, R. D.; Kratz, D. P.; Caldwell, J.; Kim, S. J.

    1986-01-01

    Mutually consistent line-by-line, narrow-band and broad-band infrared radiation models are presented for methane, a potentially important anthropogenic trace gas within the atmosphere. Comparisons of the modeled band absorptances with existing laboratory data produce the best agreement when, within the band models, spurious band intensities are used which are consistent with the respective laboratory data sets, but which are not consistent with current knowledge concerning the intensity of the infrared fundamental band of methane. This emphasizes the need for improved laboratory band absorptance measurements. Since, when applied to atmospheric radiation calculations, the line-by-line model does not require the use of scaling approximations, the mutual consistency of the band models provides a means of appraising the accuracy of scaling procedures. It is shown that Curtis-Godson narrow-band and Chan-Tien broad-band scaling provide accurate means of accounting for atmospheric temperature and pressure variations.

  14. Development of an infrared radiative heating model

    NASA Technical Reports Server (NTRS)

    Bergstrom, R. W.; Helmle, L. C.

    1979-01-01

    Infrared radiative transfer solution algorithms used in global circulation models were assessed. Computation techniques applicable to the Ames circulation model are identified. Transmission properties of gaseous CO2, H2O, and O3 are gathered, and a computer program is developed, using the line parameter tape and Voight profile subroutine, which computes the transmission of CO2, H2O, and O3. A computer code designed to compute atmospheric cooling rates was developed.

  15. New powerful metal vapor lasers oscillating in deep ultraviolet and middle infrared spectral ranges

    NASA Astrophysics Data System (ADS)

    Temelkov, K. A.; Vuchkov, N. K.; Sabotinov, N. V.

    2010-09-01

    Middle infrared and deep ultraviolet laser systems, which are based on high-power high-beam-quality stable-operating He-SrBr2 and Cu+ Ne-CuBr lasers excited in nanosecond pulsed longitudinal discharge, are developed, patented and studied. Optimal discharge conditions, such as active zone diameter, vapor pressure, buffer-gas pressure, electrical excitation scheme parameters, average input power, pulse repetition frequency, are found. The highest output laser parameters are obtained for the Sr atom and Cu+ lasers, respectively. These lasers equipped with optical systems for control of laser radiation parameters, such as laser beam divergence, laser intensity distribution, etc. are used in a large variety of applications, such as precise material microprocessing, including biological tissues, determination of linear optical properties of different materials newly developed, laser-induced modification of conductive polymers, laserinduced fluorescence in wide-gap semiconductors, instead of free electron and excimer lasers, respectively.

  16. Fourier transform infrared spectroscopy (FTIR) of laser-irradiated cementum

    NASA Astrophysics Data System (ADS)

    Rechmann, Peter; White, Joel M.; Cecchini, Silvia C. M.; Hennig, Thomas

    2003-06-01

    Utilizing Fourier Transform Infrared Spectroscopy (FTIR) in specular reflectance mode chemical changes of root cement surfaces due to laser radiation were investigated. A total of 18 samples of root cement were analyzed, six served as controls. In this study laser energies were set to those known for removal of calculus or for disinfection of periodontal pockets. Major changes in organic as well as inorganic components of the cementum were observed following Nd:YAG laser irradiation (wavelength 1064 nm, pulse duration 250 μs, free running, pulse repetition rate 20 Hz, fiber diameter 320 μm, contact mode; Iskra Twinlight, Fontona, Slovenia). Er:YAG laser irradiation (wavelength 2.94 μm, pulse duration 250 μs, free running, pulse repetition rate 6 Hz, focus diameter 620 μm, air water cooling 30 ml/min; Iskra Twinlight, Fontona, Slovenia) significantly reduced the Amid bands due to changes in the organic components. After irradiation with a frequency doubled Alexandrite laser (wavelength 377 nm, pulse duration 200 ns, q-switched, pulse repetition rate 20 Hz, beam diameter 800 μm, contact mode, water cooling 30 ml/min; laboratory prototype) only minimal reductions in the peak intensity of the Amide-II band were detected.

  17. Band models and correlations for infrared radiation

    NASA Technical Reports Server (NTRS)

    Tiwari, S. N.

    1975-01-01

    Absorption of infrared radiation by various line and band models are briefly reviewed. Narrow band model relations for absorptance are used to develop 'exact' formulations for total absorption by four wide band models. Application of a wide band model to a particular gas largely depends upon the spectroscopic characteristic of the absorbing-emitting molecule. Seven continuous correlations for the absorption of a wide band model are presented and each one of these is compared with the exact (numerical) solutions of the wide band models. Comparison of these results indicate the validity of a correlation for a particular radiative transfer application. In radiative transfer analyses, use of continuous correlations for total band absorptance provides flexibilities in various mathematical operations.

  18. Low-intensity infrared lasers alter actin gene expression in skin and muscle tissue

    NASA Astrophysics Data System (ADS)

    Fonseca, A. S.; Mencalha, A. L.; Campos, V. M. A.; Ferreira-Machado, S. C.; Peregrino, A. A. F.; Magalhães, L. A. G.; Geller, M.; Paoli, F.

    2013-02-01

    The biostimulative effect of low-intensity lasers is the basis for treatment of diseases in soft tissues. However, data about the influence of biostimulative lasers on gene expression are still scarce. The aim of this work was to evaluate the effects of low-intensity infrared lasers on the expression of actin mRNA in skin and muscle tissue. Skin and muscle tissue of Wistar rats was exposed to low-intensity infrared laser radiation at different fluences and frequencies. One and 24 hours after laser exposure, tissue samples were withdrawn for total RNA extraction, cDNA synthesis and evaluation of actin gene expression by quantitative polymerase chain reaction. The data obtained show that laser radiation alters the expression of actin mRNA differently in skin and muscle tissue of Wistar rats depending of the fluence, frequency and time after exposure. The results could be useful for laser dosimetry, as well as to justify the therapeutic protocols for treatment of diseases of skin and muscle tissues based on low-intensity infrared laser radiation.

  19. The Visualization of Infrared Radiation Using Thermal Sensitive Foils

    ERIC Educational Resources Information Center

    Bochnícek, Zdenek

    2013-01-01

    This paper describes a set of demonstration school experiments where infrared radiation is detected using thermal sensitive foils. The possibility of using standard glass lenses for infrared imaging is discussed in detail. It is shown that with optic components made from glass, infrared radiation up to 2.5 µm of wavelength can be detected. The…

  20. Picosecond infrared laser (PIRL): an ideal phonomicrosurgical laser?

    PubMed

    Hess, Markus; Hildebrandt, Michael Dominik; Müller, Frank; Kruber, Sebastian; Kroetz, Peter; Schumacher, Udo; Reimer, Rudolph; Kammal, Michael; Püschel, Klaus; Wöllmer, Wolfgang; Miller, Dwayne

    2013-11-01

    A comparison of tissue cutting effects in excised cadaver human vocal folds after incisions with three different instruments [scalpel, CO2 laser and the picosecond infrared laser-(PIRL)] was performed. In total, 15 larynges were taken from human cadavers shortly after death. After deep freezing and thawing for the experiment, the vocal folds suspended in the hemilarynx were incised. Histology and environmental scanning electron microscopy (ESEM) analyses were performed. Damage zones after cold instrument cuts ranged from 51 to 135 μm, as compared to 9-28 μm after cutting with the PIRL. It was shown that PIRL incision had smaller zones of tissue coagulation and tissue destruction, when compared with scalpel and CO2 laser cuts. The PIRL technology provides an (almost) atraumatic laser, which offers a quantum jump towards realistic 'micro'-phonosurgery on a factual cellular dimension, almost entirely avoiding coagulation, carbonization, or other ways of major tissue destruction in the vicinity of the intervention area. Although not available for clinical use yet, the new technique appears promising for future clinical applications, so that technical and methodological characteristics as well as tissue experiments seem worthwhile to be communicated at this stage of development. PMID:23708442

  1. Infrared microcalorimetric spectroscopy using quantum cascade lasers

    SciTech Connect

    Morales Rodriguez, Marissa E; Senesac, Larry R; Rajic, Slobodan; Lavrik, Nickolay V; Smith, Barton; Datskos, Panos G

    2013-01-01

    We have investigated an infrared (IR) microcalorimetric spectroscopy technique that can be used to detect the presence of trace amounts of target molecules. The chemical detection is accomplished by obtaining the IR photothermal spectra of molecules absorbed on the surface of uncooled thermal micromechanical detectors. IR microcalorimetric spectroscopy requires no chemical specific coatings and the chemical specificity of the presented method is a consequence of the wavelength-specific absorption of IR photons from tunable quantum cascade lasers due to vibrational spectral bands of the analyte. We have obtained IR photothermal spectra for trace concentrations of RDX and a monolayer of 2-mercaptoethanol, over the wavelength region from 6 to 10 m. We found that in this wavelength region both chemicals exhibit a number of photothermal absorption features that are in good agreement with their respective IR spectra.

  2. Low-intensity red and infrared laser effects at high fluences on Escherichia coli cultures

    PubMed Central

    Barboza, L.L.; Campos, V.M.A.; Magalhães, L.A.G.; Paoli, F.; Fonseca, A.S.

    2015-01-01

    Semiconductor laser devices are readily available and practical radiation sources providing wavelength tenability and high monochromaticity. Low-intensity red and near-infrared lasers are considered safe for use in clinical applications. However, adverse effects can occur via free radical generation, and the biological effects of these lasers from unusually high fluences or high doses have not yet been evaluated. Here, we evaluated the survival, filamentation induction and morphology of Escherichia coli cells deficient in repair of oxidative DNA lesions when exposed to low-intensity red and infrared lasers at unusually high fluences. Cultures of wild-type (AB1157), endonuclease III-deficient (JW1625-1), and endonuclease IV-deficient (JW2146-1) E. coli, in exponential and stationary growth phases, were exposed to red and infrared lasers (0, 250, 500, and 1000 J/cm2) to evaluate their survival rates, filamentation phenotype induction and cell morphologies. The results showed that low-intensity red and infrared lasers at high fluences are lethal, induce a filamentation phenotype, and alter the morphology of the E. coli cells. Low-intensity red and infrared lasers have potential to induce adverse effects on cells, whether used at unusually high fluences, or at high doses. Hence, there is a need to reinforce the importance of accurate dosimetry in therapeutic protocols. PMID:26445339

  3. Low-intensity red and infrared laser effects at high fluences on Escherichia coli cultures.

    PubMed

    Barboza, L L; Campos, V M A; Magalhães, L A G; Paoli, F; Fonseca, A S

    2015-10-01

    Semiconductor laser devices are readily available and practical radiation sources providing wavelength tenability and high monochromaticity. Low-intensity red and near-infrared lasers are considered safe for use in clinical applications. However, adverse effects can occur via free radical generation, and the biological effects of these lasers from unusually high fluences or high doses have not yet been evaluated. Here, we evaluated the survival, filamentation induction and morphology of Escherichia coli cells deficient in repair of oxidative DNA lesions when exposed to low-intensity red and infrared lasers at unusually high fluences. Cultures of wild-type (AB1157), endonuclease III-deficient (JW1625-1), and endonuclease IV-deficient (JW2146-1) E. coli, in exponential and stationary growth phases, were exposed to red and infrared lasers (0, 250, 500, and 1000 J/cm2) to evaluate their survival rates, filamentation phenotype induction and cell morphologies. The results showed that low-intensity red and infrared lasers at high fluences are lethal, induce a filamentation phenotype, and alter the morphology of the E. coli cells. Low-intensity red and infrared lasers have potential to induce adverse effects on cells, whether used at unusually high fluences, or at high doses. Hence, there is a need to reinforce the importance of accurate dosimetry in therapeutic protocols. PMID:26445339

  4. Pigments which reflect infrared radiation from fire

    DOEpatents

    Berdahl, P.H.

    1998-09-22

    Conventional paints transmit or absorb most of the intense infrared (IR) radiation emitted by fire, causing them to contribute to the spread of fire. The present invention comprises a fire retardant paint additive that reflects the thermal IR radiation emitted by fire in the 1 to 20 micrometer ({micro}m) wavelength range. The important spectral ranges for fire control are typically about 1 to about 8 {micro}m or, for cool smoky fires, about 2 {micro}m to about 16 {micro}m. The improved inventive coatings reflect adverse electromagnetic energy and slow the spread of fire. Specific IR reflective pigments include titanium dioxide (rutile) and red iron oxide pigments with diameters of about 1 {micro}m to about 2 {micro}m and thin leafing aluminum flake pigments. 4 figs.

  5. Pigments which reflect infrared radiation from fire

    DOEpatents

    Berdahl, Paul H.

    1998-01-01

    Conventional paints transmit or absorb most of the intense infrared (IR) radiation emitted by fire, causing them to contribute to the spread of fire. The present invention comprises a fire retardant paint additive that reflects the thermal IR radiation emitted by fire in the 1 to 20 micrometer (.mu.m) wavelength range. The important spectral ranges for fire control are typically about 1 to about 8 .mu.m or, for cool smoky fires, about 2 .mu.m to about 16 .mu.m. The improved inventive coatings reflect adverse electromagnetic energy and slow the spread of fire. Specific IR reflective pigments include titanium dioxide (rutile) and red iron oxide pigments with diameters of about 1 .mu.m to about 2 .mu.m and thin leafing aluminum flake pigments.

  6. Remote infrared radiation detection using piezoresistive microcantilevers

    SciTech Connect

    Datskos, P.G.; Oden, P.I.; Thundat, T.; Wachter, E.A.; Warmack, R.J.; Hunter, S.R.

    1996-11-01

    A novel micromechanical infrared (IR) radiation sensor has been developed using commercially available piezoresistive microcantilevers. Microcantilevers coated with a heat absorbing layer undergo bending due to the differential stress between the top layer (coating) and the substrate. The bending causes a change in the piezoresistance and is proportional to the amount of heat absorbed. The microcantilever IR sensor exhibits two distinct thermal responses: a fast one ({lt}ms) and a slower one ({approximately}10 ms). A noise equivalent power (at a modulation frequency of 30 Hz) was estimated to be {approximately}70 nW/Hz{sup 1/2}. This value can be further reduced by designing microcantilevers with better thermal isolation that can allow microcantilevers to be used as uncooled IR radiation detectors. {copyright} {ital 1996 American Institute of Physics.}

  7. Infrared radiation models for atmospheric ozone

    NASA Technical Reports Server (NTRS)

    Kratz, David P.; Ces, Robert D.

    1988-01-01

    A hierarchy of line-by-line, narrow-band, and broadband infrared radiation models are discussed for ozone, a radiatively important atmospheric trace gas. It is shown that the narrow-band (Malkmus) model is in near-precise agreement with the line-by-line model, thus providing a means of testing narrow-band Curtis-Godson scaling, and it is found that this scaling procedure leads to errors in atmospheric fluxes of up to 10 percent. Moreover, this is a direct consequence of the altitude dependence of the ozone mixing ratio. Somewhat greater flux errors arise with use of the broadband model, due to both a lesser accuracy of the broadband scaling procedure and to inherent errors within the broadband model, despite the fact that this model has been tuned to the line-by-line model.

  8. Infrared Thermographic Study of Laser Ignition

    SciTech Connect

    Mohler, Jonathan H.; Chow, Charles T. S.

    1986-07-01

    Pyrotechnic ignition has been studied in the past by making a limited number of discrete temperature-time observations during ignition. Present-day infrared scanning techniques make it possible to record thermal profiles, during ignition, with high spacial and temporal resolution. Data thus obtained can be used with existing theory to characterize pyrotechnic materials and to develop more precise kinetic models of the ignition process. Ignition has been studied theoretically and experimentally using various thermal methods. It has been shown that the whole process can, ideally, be divided into two stages. In the first stage, the sample pellet behaves like an inert body heated by an external heat source. The second stage is governed by the chemical reaction in the heated volume produced during the first stage. High speed thermographic recording of the temperature distribution in the test sample during laser ignition makes it possible to calculate the heat content at any instant. Thus, one can actually observe laser heating and the onset of self-sustained combustion in the pellet. The experimental apparatus used to make these observations is described. The temperature distributions recorded are shown to be in good agreement with those predicted by heat transfer theory. Heat content values calculated from the observed temperature distributions are used to calculate thermal and kinetic parameters for several samples. These values are found to be in reasonable agreement with theory.

  9. Effect of infrared radiation on the lens

    PubMed Central

    Aly, Eman Mohamed; Mohamed, Eman Saad

    2011-01-01

    Background: Infrared (IR) radiation is becoming more popular in industrial manufacturing processes and in many instruments used for diagnostic and therapeutic application to the human eye. Aim: The present study was designed to investigate the effect of IR radiation on rabbit’s crystalline lens and lens membrane. Materials and Methods: Fifteen New Zealand rabbits were used in the present work. The rabbits were classified into three groups; one of them served as control. The other two groups were exposed to IR radiation for 5 or 10 minutes. Animals from these two irradiated groups were subdivided into two subgroups; one of them was decapitated directly after IR exposure, while the other subgroup was decapitated 1 hour post exposure. IR was delivered from a General Electric Lamp model 250R 50/10, placed 20 cm from the rabbit and aimed at each eye. The activity of Na+-K+ ATPase was measured in the lens membrane. Soluble lens proteins were extracted and the following measurements were carried out: estimation of total soluble protein, sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) and Fourier transform infrared (FTIR) spectroscopy. For comparison between multiple groups, analysis of variance was used with significance level set at P < 0.001. Results: The results indicated a change in the molecular weight of different lens crystalline accompanied with changes in protein backbone structure. These changes increased for the groups exposed to IR for 10 minutes. Moreover, the activity of Na+-K+ ATPase significantly decreased for all groups. Conclusions: The protein of eye lens is very sensitive to IR radiation which is hazardous and may lead to cataract. PMID:21350278

  10. Tunable diode lasers for 3-30 micron infrared operation

    NASA Technical Reports Server (NTRS)

    Linden, K. J.

    1983-01-01

    The tunable diode laser is now widely used in high resolution infrared spectroscopy studies, taking into account laboratory and industrial applications. The present investigation is concerned with advances related to laser performance and reliability. The advances are the result of improvements in materials and device technologies. Reliability data for broad-area Pb(1-x)Sn(x)Se lasers are considered along with performance improvements in stripe-geometry lasers, laser performance at wavelengths above 25 microns, and laser performance at wavelengths below 4 microns. Attention is given to tunable Pb-salt infrared diode lasers, mesa-stripe geometry lasers of Pb(1-x)Sn(x)Se and PbS(1-x)Se(x), and long wavelength diode laser emission observed in both Pb(1-x)Sn(x)Te and Pb(1-x)Sn(x)Se.

  11. Comparative hazard evaluation of near-infrared diode lasers.

    PubMed

    Marshall, W J

    1994-05-01

    Hazard evaluation methods from various laser protection standards differ when applied to extended-source, near-infrared lasers. By way of example, various hazard analyses are applied to laser training systems, which incorporate diode lasers, specifically those that assist in training military or law enforcement personnel in the proper use of weapons by simulating actual firing by the substitution of a beam of near-infrared energy for bullets. A correct hazard evaluation of these lasers is necessary since simulators are designed to be directed toward personnel during normal use. The differences among laser standards are most apparent when determining the hazard class of a laser. Hazard classification is based on a comparison of the potential exposures with the maximum permissible exposures in the 1986 and 1993 versions of the American National Standard for the Safe Use of Lasers, Z136.1, and the accessible emission limits of the federal laser product performance standard. Necessary safety design features of a particular system depend on the hazard class. The ANSI Z136.1-1993 standard provides a simpler and more accurate hazard assessment of low-power, near-infrared, diode laser systems than the 1986 ANSI standard. Although a specific system is evaluated, the techniques described can be readily applied to other near-infrared lasers or laser training systems. PMID:8175359

  12. Radiation response issues for infrared detectors

    NASA Technical Reports Server (NTRS)

    Kalma, Arne H.

    1990-01-01

    Researchers describe the most important radiation response issues for infrared detectors. In general, the two key degradation mechanisms in infrared detectors are the noise produced by exposure to a flux of ionizing particles (e.g.; trapped electronics and protons, debris gammas and electrons, radioactive decay of neutron-activated materials) and permanent damage produced by exposure to total dose. Total-dose-induced damage is most often the result of charge trapping in insulators or at interfaces. Exposure to short pulses of ionization (e.g.; prompt x rays or gammas, delayed gammas) will cause detector upset. However, this upset is not important to a sensor unless the recovery time is too long. A few detector technologies are vulnerable to neutron-induced displacement damage, but fortunately most are not. Researchers compare the responses of the new technologies with those of the mainstream technologies of PV HgCdTe and IBC Si:As. One important reason for this comparison is to note where some of the newer technologies have the potential to provide significantly improved radiation hardness compared with that of the mainstream technologies, and thus to provide greater motivation for the pursuit of these technologies.

  13. Infrared Signature Masking by Air Plasma Radiation

    NASA Technical Reports Server (NTRS)

    Kruger, Charles H.; Laux, C. O.

    2001-01-01

    This report summarizes the results obtained during a research program on the infrared radiation of air plasmas conducted in the High Temperature Gasdynamics Laboratory at Stanford University under the direction of Professor Charles H. Kruger, with Dr. Christophe O. Laux as Associate Investigator. The goal of this research was to investigate the masking of infrared signatures by the air plasma formed behind the bow shock of high velocity missiles. To this end, spectral measurements and modeling were made of the radiation emitted between 2.4 and 5.5 micrometers by an atmospheric pressure air plasma in chemical and thermal equilibrium at a temperature of approximately 3000 K. The objective was to examine the spectral emission of air species including nitric oxide, atomic oxygen and nitrogen lines, molecular and atomic continua, as well as secondary species such as water vapor or carbon dioxide. The cold air stream injected in the plasma torch contained approximately 330 parts per million of CO2, which is the natural CO2 concentration in atmospheric air at room temperatures, and a small amount of water vapor with an estimated mole fraction of 3.8x10(exp -4).

  14. Infrared Signature Masking by Air Plasma Radiation

    NASA Technical Reports Server (NTRS)

    Kruger, C. H.; Laux, C. O.

    1998-01-01

    This report describes progress during the second year of our research program on Infrared Signature Masking by Air Plasmas at Stanford University. This program is intended to investigate the masking of infrared signatures by the air plasma formed behind the bow shock of high velocity missiles. Our previous annual report described spectral measurements and modeling of the radiation emitted between 3.2 and 5.5 microns by an atmospheric pressure air plasma in chemical and thermal equilibrium at a temperature of approximately 3100 K. One of our goals was to examine the spectral emission of secondary species such as water vapor or carbon dioxide. The cold air stream injected in the plasma torch contained approximately 330 parts per million Of CO2, which is the natural CO2 concentration in atmospheric air at room temperature, and a small amount of water vapor with an estimated mole fraction of 3.8 x 10(exp -4). As can be seen from Figure 1, it was found that the measured spectrum exhibited intense spectral features due to the fundamental rovibrational bands of NO at 4.9 - 5.5 microns and the V(3) band of CO2 (antisymmetric stretch) at 4.2-4.8 microns. These observations confirmed the well-known fact that infrared signatures between 4.15 - 5.5 microns can be masked by radiative emission in the interceptor's bow-shock. Figure I also suggested that the range 3.2 - 4.15 microns did not contain any significant emission features (lines or continuum) that could mask IR signatures. However, the signal-to-noise level, close to one in that range, precluded definite conclusions. Thus, in an effort to further investigate the spectral emission in the range of interest to signature masking problem, new measurements were made with a higher signal-to-noise ratio and an extended wavelength range.

  15. Applications of the Infrared Free Electron Laser in Nonlinear and Time-Resolved Spectroscopy

    NASA Astrophysics Data System (ADS)

    Fann, Wunshain

    1990-01-01

    Free Electron Lasers (FEL) have been envisioned as novel radiation sources tunable over a wide spectral range. In this dissertation I report two types of experiments that used the infrared FEL, Mark III, to study nonlinear optical properties of conjugated polymers and the possibility of long lived vibrational excitations in acetanilide, a hydrogen-bonded molecular crystal.

  16. Infrared Laser Desorption: Mechanisms and Applications

    NASA Astrophysics Data System (ADS)

    Maechling, Claude Ricketts

    1995-01-01

    This thesis describes the use of two-step laser mass spectrometry (L^2MS), a combination of infrared (IR) laser desorption with resonance-enhanced multiphoton ionization (REMPI) and time-of-flight (TOF) mass spectrometry, to investigate (1) the mechanism of IR laser desorption, (2) the composition of aromatic molecules in extraterrestrial samples, and (3) the measurement of compound-specific carbon isotope ratios. First, a description of the mechanism of IR laser desorption of monolayer and submonolayer coverages of molecules adsorbed to an insulator surface is presented. The vibrational and translational energy distributions of aniline-d7 molecules desorbed from single-crystal sapphire (Al_2 O_3) are recorded using L ^2MS. The energy distributions are found to be in equilibrium with each other and with the temperature of the surface at the time of desorption. The translational and angular distributions of monolayer coverages are altered by the collisions of desorbing molecules with each other. Second, spatial and chemical analyses of the carbonaceous components in chondritic meteorites are presented. A microprobe L^2MS instrument (mu L^2MS) capable of analyzing samples with a spatial resolution of 40 mu m and zeptomole (10^{-21} mole) sensitivity is described and used to investigate polycyclic aromatic hydrocarbons (PAHs) in small particles and heterogeneous samples. PAH distributions are used to distinguish between samples from different meteorite classes, and the effects of thermal processing within a given meteorite class are observed. Sliced wafers of meteorite are found to contain an inhomogeneous distribution of PAHs. muL^2MS studies of meteorite samples are coordinated with scanning electron microscopy studies, and the abundances of aromatic compounds across the surface of a sample are consistent with gross structural features but not with elemental or mineralogical features. Third, a description of a method for performing compound-specific carbon isotope

  17. Effects of radiation on laser diodes.

    SciTech Connect

    Phifer, Carol Celeste

    2004-09-01

    The effects of ionizing and neutron radiation on the characteristics and performance of laser diodes are reviewed, and the formation mechanisms for nonradiative recombination centers, the primary type of radiation damage in laser diodes, are discussed. Additional topics include the detrimental effects of aluminum in the active (lasing) volume, the transient effects of high-dose-rate pulses of ionizing radiation, and a summary of ways to improve the radiation hardness of laser diodes. Radiation effects on laser diodes emitting in the wavelength region around 808 nm are emphasized.

  18. Effect of microstructure on the coupled electromagnetic-thermo-mechanical response of cyclotrimethylenetrinitramine-estane energetic aggregates to infrared laser radiation

    SciTech Connect

    Brown, Judith A.; Zikry, M. A.

    2015-09-28

    The coupled electromagnetic (EM)-thermo-mechanical response of cyclotrimethylenetrinitramine-estane energetic aggregates under laser irradiation and high strain rate loads has been investigated for various aggregate sizes and binder volume fractions. The cyclotrimethylenetrinitramine (RDX) crystals are modeled with a dislocation density-based crystalline plasticity formulation and the estane binder is modeled with finite viscoelasticity through a nonlinear finite element approach that couples EM wave propagation with laser heat absorption, thermal conduction, and inelastic deformation. Material property and local behavior mismatch at the crystal-binder interfaces resulted in geometric scattering of the EM wave, electric field and laser heating localization, high stress gradients, dislocation density, and crystalline shear slip accumulation. Viscous sliding in the binder was another energy dissipation mechanism that reduced stresses in aggregates with thicker binder ligaments and larger binder volume fractions. This investigation indicates the complex interactions between EM waves and mechanical behavior, for accurate predictions of laser irradiation of heterogeneous materials.

  19. Tunable excitation of mid-infrared optically pumped semiconductor lasers

    NASA Astrophysics Data System (ADS)

    Olafsen, Linda J.; Kunz, Jeremy; Ongstad, Andrew P.; Kaspi, Ron

    2013-01-01

    While conventional semiconductor lasers employ electrical injection for carrier excitation, optically pumped semiconductor lasers (OPSLs) have demonstrated high output powers and high brightness in the mid-infrared. An important consideration for optically pumped lasers is efficient absorption of the pump beam, which can be achieved through increasing the number of periods in the active region, by placing the active region in a cavity with an optical thickness of twice the pump wavelength between distributed Bragg reflectors (Optical Pumping Injection Cavity), or by periodically inserting the active quantum wells into an InGaAsSb waveguide designed to absorb the pump radiation (Integrated Absorber). A tunable optical pumping technique is utilized by which threshold intensities are minimized and efficiencies are maximized. The near-IR idler output of a Nd:YAG-pumped optical parametric oscillator (10 Hz, ~4 ns) is the tunable optical pumping source in this work. Results are presented for an OPSL with a type-II W active region embedded in an integrated absorber to enhance the absorption of the optical pump beam. Emission wavelengths range from 4.64 μm at 78 K to 4.82 μm at 190 K for optical pump wavelengths ranging from 1930-1950 nm. The effect of wavelength tuning is demonstrated and compared to single wavelength pumping (1940 nm) at a higher duty cycle (20- 30%). Comparisons are also made to other OPSLs, including a discussion of the characteristic temperature and high temperature performance of these devices.

  20. Radiation effects in IRAS extrinsic infrared detectors

    NASA Technical Reports Server (NTRS)

    Varnell, L.; Langford, D. E.

    1982-01-01

    During the calibration and testing of the Infrared Astronomy Satellite (IRAS) focal plane, it was observed that the extrinsic photoconductor detectors were affected by gamma radiation at dose levels of the order of one rad. Since the flight environment will subject the focal plane to dose levels of this order from protons in single pass through the South Atlantic Anomaly, an extensive program of radiation tests was carried out to measure the radiation effects and to devise a method to counteract these effects. The effects observed after irradiation are increased responsivity, noise, and rate of spiking of the detectors after gamma-ray doses of less than 0.1 rad. The detectors can be returned almost to pre-irradiation performance by increasing the detector bias to breakdown and allowing a large current to flow for several minutes. No adverse effects on the detectors have been observed from this bias boost, and this technique will be used for IRAS with frequent calibration to ensure the accuracy of observations made with the instrument.

  1. Alteration of GABAergic Neurotransmission by Pulsed Infrared Laser Stimulation

    PubMed Central

    Feng, Hua-Jun; Kao, Chris; Gallagher, Martin J.; Jansen, E. Duco; Mahadevan-Jansen, Anita; Konrad, Peter E.; Macdonald, Robert L.

    2011-01-01

    Transient electrical impulses are conventionally used to elicit physiological responses in excitable tissues. While electrical stimulation has many advantages, it requires an electrode-tissue interface, exhibits relatively low spatial selectivity and always produces a “stimulus artifact”. Recently, it has been shown that pulsed, low-energy infrared laser light can evoke nerve, muscle and sensory responses similar to those induced by traditional electrical stimulation in a contact-free, damage-free, artifact-free and spatially selective manner. However, the effect of transient infrared laser light on neurotransmission in the CNS is still largely unknown. Here, we tested the effect of infrared laser light on GABAergic neurotransmission. We recorded spontaneous inhibitory postsynaptic currents (sIPSCs) from cultured rat cortical neurons prior to and after infrared laser stimulation. Using transient infrared laser light, we either stimulated the neuronal soma that had axonal projections to the recorded neuron or directly stimulated the axons that projected to the recorded neuron. Optical stimulation led to enhanced amplitude, decreased decay time constant and increased frequency of sIPSCs. These alterations of sIPSC properties produced by optical stimulation were specifically mediated by GABAA receptors and caused by the transient laser light per se since no exogenous substances such as caged compounds were used. These data show that optical stimulation using transient infrared laser light can alter GABAergic neurotransmission and demonstrate that it may be an alternative approach to electrical stimulation in studying GABAergic function. PMID:20654645

  2. Thermal Infrared Radiative Forcing By Atmospheric Aerosol

    NASA Astrophysics Data System (ADS)

    Adhikari, Narayan

    The work mainly focuses on the study of thermal infrared (IR) properties of atmospheric greenhouse gases and aerosols, and the estimation of the aerosol-induced direct longwave (LW) radiative forcing in the spectral region 5-20 mum at the Earth's surface (BOA; bottom of the atmosphere) and the top of the atmosphere (TOA) in cloud-free atmospheric conditions. These objectives were accomplished by conducting case studies on clear sky, smoky, and dusty conditions that took place in the Great Basin of the USA in 2013. Both the solar and thermal IR measurements and a state-of-the-science radiative transfer model, the LBLDIS, a combination of the Line-By-Line Radiative Transfer Model and the Discrete Ordinate Radiative Transfer (DISORT) solver were employed for the study. The LW aerosol forcing is often not included in climate models because the aerosol effect on the LW is often assumed to be negligible. We lack knowledge of aerosol characteristics in the LW region, and aerosol properties exhibit high variability. We have found that the LW TOA radiative forcing due to fine mode aerosols, mainly associated with small biomass burning smoke particles, is + 0.4 W/m2 which seems to be small, but it is similar to the LW radiative forcing due to increase in CO2 concentration in the Earth's atmosphere since the preindustrial era of 1750 (+ 1.6 W/m 2). The LW radiative forcing due to coarse mode aerosols, associated with large airborne mineral dust particles, was found to be as much as + 5.02 W/m2 at the surface and + 1.71 W/m2 at the TOA. All of these significant positive values of the aerosol radiative forcing both at the BOA and TOA indicate that the aerosols have a heating effect in the LW range, which contributes to counterbalancing the cooling effect associated with the aerosol radiative forcing in the shortwave (SW) spectral region. In the meantime, we have found that LW radiative forcing by aerosols is highly sensitive to particle size and complex refractive indices of

  3. Probe And Enhancement Of SBS Based Phonons In Infrared Fibers Using Waveguide Coupled External Radiation

    NASA Astrophysics Data System (ADS)

    Yu, Chung; Chong, Yat C.; Fong, Chee K.

    1989-06-01

    Interaction of GHz and MHz radiation with CO2 laser propagation in a silver halide fiber using sBs based phonon coupling is furthet investigated. The external signal serves to both probe and enhance laser generated sBs phonons in the fiber. Efficient coupling of microwave radiation into the fiber is accomplished by placing the fiber in a hollow metallic waveguide, designed and constructed to transmit the dominant mode in the 0.9-2.0 GHz band. MHz radiation is conveniently coupled into the fiber using the guided microwave radiation as carrier. Phonon emissions from the fiber under CO2 laser pumping are first established on a spectrum analyzer; low frequency generators ale then tuned to match these frequencies and their maximum interaction recorded. Such interactions are systematically studied by monitoring the amplitude and waveform of the reflected and transmitted laser pulse at various power levels and frequencies of the externally coupled radiation. A plot of reflected laser power versus incident laser power reveals a distinct sBs generated phonon threshold. Variouslaunch directions of the GHz and MHz radiation with respect to the direction of laser propagation are realized to verify theory governing sBs interactions. The MHz radiation and its associated phonons in the fiber are convenient tools for probing sBs related phenomenon in infrared fibers.

  4. Infrared radiation of thin plastic films.

    NASA Technical Reports Server (NTRS)

    Tien, C. L.; Chan, C. K.; Cunnington, G. R.

    1972-01-01

    A combined analytical and experimental study is presented for infrared radiation characteristics of thin plastic films with and without a metal substrate. On the basis of the thin-film analysis, a simple analytical technique is developed for determining band-averaged optical constants of thin plastic films from spectral normal transmittance data for two different film thicknesses. Specifically, the band-averaged optical constants of polyethylene terephthalate and polyimide were obtained from transmittance measurements of films with thicknesses in the range of 0.25 to 3 mil. The spectral normal reflectance and total normal emittance of the film side of singly aluminized films are calculated by use of optical constants; the results compare favorably with measured values.

  5. Transport of infrared radiation in cuboidal clouds

    NASA Technical Reports Server (NTRS)

    HARSHVARDHAN; Weinman, J. A.; Davies, R.

    1981-01-01

    The transport of infrared radiation in a single cuboidal cloud using a vertical two steam approximation was modeled. The emittance of the top face of the model cloud is always less than that for a plane parallel cloud of the same optical depth. The hemisphere flux escaping from the cloud top has a gradient from the center to the edges which brighten when the cloud is over warmer ground. Cooling rate calculations in the 8 to 13.6 micrometer region show that there is cooling from the sides of the cloud at all levels even when there is heating of the core from the ground below. The radiances exiting from model cuboidal clouds were computed by path integration over the source function obtained with the two stream approximation. It is suggested that the brightness temperature measured from finite clouds will overestimate the cloud top temperature.

  6. Radiative Transfer Simulations of Infrared Dark Clouds

    NASA Astrophysics Data System (ADS)

    Pavlyuchenkov, Yaroslav; Wiebe, Dmitry; Fateeva, Anna; Vasyunina, Tatiana

    2011-04-01

    The determination of prestellar core structure is often based on observations of (sub)millimeter dust continuum. However, recently the Spitzer Space Telescope provided us with IR images of many objects not only in emission but also in absorption. We developed a technique to reconstruct the density and temperature distributions of protostellar objects based on radiation transfer (RT) simulations both in mm and IR wavelengths. Best-fit model parameters are obtained with the genetic algorithm. We apply the method to two cores of Infrared Dark Clouds and show that their observations are better reproduced by a model with an embedded heating source despite the lack of 70 μm emission in one of these cores. Thus, the starless nature of massive cores can only be established with the careful case-by-case RT modeling.

  7. Infrared laser in the treatment of craniomandibular disorders, arthrogenous pain

    SciTech Connect

    Hansson, T.L.

    1989-05-01

    The fast removal of intra-articular inflammation of the temporomandibular joint in five different patients after infrared laser application is described. Parameters of clinical evaluation was maximum mouth opening and subjective pain. The application of infrared laser of 700 Hz frequency for 3 minutes during five consecutive days at the skin over the painful area of the temporomandibular joint was used. However, the importance of concomitant mandibular stabilization is stressed to achieve optimal result.

  8. Infrared radiation budget of the Harmattan haze. [West Africa

    NASA Technical Reports Server (NTRS)

    Kuhn, P. M.; Weickmann, H. K.

    1975-01-01

    Infrared in situ observations of the West African Harmaltan Haze during the 1974 GATE field phase were conducted to determine the radiative properties of the tropospheric phenomenon and to develop a calculation model for radiative transfer through the haze. Radiometric observations of the dust haze were analyzed for haze infrared transmission. Infrared and tropospheric cooling rates are given together with the haze volume absorption rate.

  9. Preliminary report of plants and processes for infrared radiation

    SciTech Connect

    Not Available

    1980-04-18

    The industrial uses and unwanted industrial occurrences of infrared radiation were discussed. The physical characteristics of infrared radiation were described. Exposure to infrared radiation was considered for the following industries: chemicals and allied products, contract construction, electrical equipment, fabricated metals, food and related products, furniture and fixtures, instruments, leather products, manufacturing, primary metals, printing and publishing, rubber and plastics, and stone, clay and glass. The extent of employee exposure to infrared radiation depended on wavelength and energy, proximity of worker to source, degree of worker protection with heat shields, clothing, and tinted goggles, and general workplace conditions. The eye was the critical organ due to its limited ability to dissipate the absorbed heat and its sensitivity to elevated intraocular temperatures. The skin was also a primary concern as it has an extensive surface area and is the initial absorber of incident infrared radiation.

  10. Method for generation of tunable far infrared radiation from two-dimensional plasmons

    NASA Technical Reports Server (NTRS)

    Katz, Joseph (Inventor)

    1989-01-01

    Tunable far infrared radiation is produced from two-dimensional plasmons in a heterostructure, which provides large inversion-layer electron densities at the heterointerface, without the need for a metallic grating to couple out the radiation. Instead, a light interference pattern is produced on the planar surface of the heterostructure using two coherent laser beams of a wavelength selected to be strongly absorbed by the heterostructure in order to penetrate through the inversion layer. The wavelength of the far infrared radiation coupled out can then be readily tuned by varying the angle between the coherent beams, or varying the wavelength of the two interfering coherent beams, thus varying the periodicity of the photoconductivity grating to vary the wavelength of the far infrared radiation being coupled out.

  11. Efficient dielectric metasurface collimating lenses for mid-infrared quantum cascade lasers.

    PubMed

    Arbabi, Amir; Briggs, Ryan M; Horie, Yu; Bagheri, Mahmood; Faraon, Andrei

    2015-12-28

    Light emitted from single-mode semiconductor lasers generally has large divergence angles, and high numerical aperture lenses are required for beam collimation. Visible and near infrared lasers are collimated using aspheric glass or plastic lenses, yet collimation of mid-infrared quantum cascade lasers typically requires more costly aspheric lenses made of germanium, chalcogenide compounds, or other infrared-transparent materials. Here we report mid-infrared dielectric metasurface flat lenses that efficiently collimate the output beam of single-mode quantum cascade lasers. The metasurface lenses are composed of amorphous silicon posts on a flat sapphire substrate and can be fabricated at low cost using a single step conventional UV binary lithography. Mid-infrared radiation from a 4.8 μm distributed-feedback quantum cascade laser is collimated using a polarization insensitive metasurface lens with 0.86 numerical aperture and 79% transmission efficiency. The collimated beam has a half divergence angle of 0.36° and beam quality factor of M2=1.02. PMID:26831996

  12. Efficient dielectric metasurface collimating lenses for mid-infrared quantum cascade lasers

    NASA Astrophysics Data System (ADS)

    Arbabi, Amir; Briggs, Ryan M.; Horie, Yu; Bagheri, Mahmood; Faraon, Andrei

    2015-12-01

    Light emitted from single-mode semiconductor lasers generally has large divergence angles, and high numerical aperture lenses are required for beam collimation. Visible and near infrared lasers are collimated using aspheric glass or plastic lenses, yet collimation of mid-infrared quantum cascade lasers typically requires more costly aspheric lenses made of germanium, chalcogenide compounds, or other infrared-transparent materials. Here we report mid-infrared dielectric metasurface flat lenses that efficiently collimate the output beam of single-mode quantum cascade lasers. The metasurface lenses are composed of amorphous silicon posts on a flat sapphire substrate and can be fabricated at low cost using a single step conventional UV binary lithography. Mid-infrared radiation from a 4.8 $\\mu$m distributed-feedback quantum cascade laser is collimated using a polarization insensitive metasurface lens with 0.86 numerical aperture and 79% transmission efficiency. The collimated beam has a half divergence angle of 0.36$^\\circ$ and beam quality factor of $M^2$=1.02.

  13. Mid-infrared laser-spectroscopic sensing of chemical species.

    PubMed

    Sigrist, Markus W

    2015-05-01

    This letter reports on mid-infrared laser-based detection and analysis of chemical species. Emphasis is put on broadly tunable laser sources and sensitive detection schemes. Selected examples from our lab illustrate the performance and potential of such systems in various areas including environmental and medical sensing. PMID:26257952

  14. Mid-infrared laser-spectroscopic sensing of chemical species

    PubMed Central

    Sigrist, Markus W.

    2014-01-01

    This letter reports on mid-infrared laser-based detection and analysis of chemical species. Emphasis is put on broadly tunable laser sources and sensitive detection schemes. Selected examples from our lab illustrate the performance and potential of such systems in various areas including environmental and medical sensing. PMID:26257952

  15. Tunable Infrared Lasers: Preparing for Expanded use in Environmental Monitoring

    NASA Technical Reports Server (NTRS)

    Menzies, R. T.; Killinger, D. K.

    1994-01-01

    The literature on the use of tunable infrared lasers, for atmospheric trace gas detection and monitoring is about 25 years of age. However, this field, whith its myriad of potential application areas, has always been driven by the available laser technology. As new or improved laser devices become available, with characteristics which lend themselves to operation in compact, nearly autonomous instruments, their application to atmospheric science and environmental measurements expands.

  16. Applications of infrared laser spectroscopy to laser chemistry and laser development

    NASA Astrophysics Data System (ADS)

    McDowell, Robin S.; Viswanath, A. K.

    The impact on infrared molecular spectroscopy of high-resolution tunable laser sources and laser-controlled Fourier-transform spectrometers is discussed, with special reference to rovibrational spectra of spherical-top molecules such as CH4, OsO4, SiF4, SF6, and UF6. The role of tunable laser spectroscopy in analyzing the CF4 laser, resulting in the precise prediction of lasing frequencies between 605 and 655/cm, is described. Studies of overtone and combination bands of SF6 enable the vibrational anharmonicity to be determined, resulting in a more detailed description of the pump transitions involved in laser photochemistry, and of higher vibrational levels and pathways to excitation and dissociation. This permits more accurate calculations of vibrational state densities for spherical-top molecules. Implications for the photochemistry of species, such as SiF4, SF6, UF6, and Ni(Co)4, are discussed.

  17. Red and infrared gas laser beam for therapy

    NASA Astrophysics Data System (ADS)

    Pascu, Mihail-Lucian; Ristici, Marin; Ristici, E.; Tivarus, Madalina-Elena

    2000-06-01

    For the low power laser therapy, the experiments show that better results are obtained when the laser beam is an overlapping of two radiations: one in the visible region of the spectrum and the other in IR region. Also, some experiments show that for good results in biostimulation it is important to have a high coherence length of laser beam; this is not the case of the laser diodes The He-Ne laser has the best coherence, being able to generate laser radiations in visible and IR. It has tow strong laser lines: 633 nm and 1.15 micrometers . Although their gains are about the same, the available power of the red radiation is 3-4 times higher because of its larger width, when they oscillate separately. Using special dichroic mirrors for simultaneous reflection of the both liens, the laser beam will consist of the two radiations, each of them having good coherence . A 420 mm active length, 1.8 mm inner diameter He-Ne laser tube and a special designed resonator has been developed. The mirrors reflect both radiations as follows: one reflects 99.9 percent and the other, the output mirror, reflects 98 percent. There is a competition between them because these lines have a common lower level. The output power of the laser beam as 6 mW for 633 nm and 4 mW for 1.15 micrometers , respectively.

  18. Transport of infrared radiation in cuboidal clouds

    NASA Technical Reports Server (NTRS)

    Harshvardhan, MR.; Weinman, J. A.; Davies, R.

    1981-01-01

    The transport of infrared radiation in a single cuboidal cloud is modeled using a variable azimuth two-stream approximation. Computations are made at 10 microns for a Deirmendjian (1969) C-1 water cloud where the single scattering albedo is equal to 0.638 and the asymmetry parameter is 0.865. The results indicate that the emittance of the top face of the model cloud is always less than that for a plane parallel cloud of the same optical depth. The hemispheric flux escaping from the cloud top possesses a gradient from the center to the edges which are warmer when the cloud is over warmer ground. Cooling rate calculations in the 8-13.6 micron region demonstrate that there is cooling out of the sides of the cloud at all levels even when there is heating of the core from the ground below. The radiances exiting from model cuboidal clouds are computed by path integration over the source function obtained with the two-stream approximation. Results indicate that the brightness temperature measured from finite clouds will overestimate the cloud-top temperature.

  19. Near infrared femtosecond laser ablation of urinary calculi in water

    NASA Astrophysics Data System (ADS)

    Qiu, Jinze; Teichman, Joel M.; Kuranov, Roman V.; McElroy, Austin B.; Wang, Tianyi; Paranjape, Amit S.; Milner, Thomas E.

    2009-02-01

    Pulsed light emitted from a near infrared (λ=800nm) femtosecond laser is capable of plasma induced photodisruption of various materials. We used femtosecond laser pulses to ablate human urinary calculi. Femtosecond pulsed laser interaction with urinary calculi was investigated with various stone compositions, different incident fluences and number of applied pulses. Spectral-domain optical coherence tomography was used to image cross sections of ablation craters on the surface of urinary calculi. Our results indicate that femtosecond laser pulses can ablate various calculi compositions. Crater diameter and depth varies from tens of microns to several hundred microns when up to 1000 pulses were applied. Future studies are required to determine if pulsed near infrared femtosecond laser pulses can be applied clinically for lithotripsy of urinary calculi.

  20. Infrared Signatures of Laser Induced Plasma in Air

    NASA Astrophysics Data System (ADS)

    Hening, Alexandru; Lu, Ryan; Ramirez, Ayax; Advanced Technology Team

    2014-03-01

    Characterization of the temporal and spatial evolution of laser generated plasma in air is necessary for the development of potential applications which range from laser induced ionized micro channels and filaments able to transfer high electric pulses over few hundreds of meters, to the generation of plasma artifacts in air, far away from the laser source. This work is focused mainly on the infrared spectrum. The influence of laser parameters (energy per pulse, pulse duration, repetition rate, wavelength and etc.) on the plasma formation and evolution has been investigated. Laser transmission losses through the air as well as through the breakdown plasma as well as their effect on infrared plasma signature are to be presented.

  1. Airborne laser systems for atmospheric sounding in the near infrared

    NASA Astrophysics Data System (ADS)

    Sabatini, Roberto; Richardson, Mark A.; Jia, Huamin; Zammit-Mangion, David

    2012-06-01

    This paper presents new techniques for atmospheric sounding using Near Infrared (NIR) laser sources, direct detection electro-optics and passive infrared imaging systems. These techniques allow a direct determination of atmospheric extinction and, through the adoption of suitable inversion algorithms, the indirect measurement of some important natural and man-made atmospheric constituents, including Carbon Dioxide (CO2). The proposed techniques are suitable for remote sensing missions performed by using aircraft, satellites, Unmanned Aerial Vehicles (UAV), parachute/gliding vehicles, Roving Surface Vehicles (RSV), or Permanent Surface Installations (PSI). The various techniques proposed offer relative advantages in different scenarios. All are based on measurements of the laser energy/power incident on target surfaces of known geometric and reflective characteristics, by means of infrared detectors and/or infrared cameras calibrated for radiance. Experimental results are presented relative to ground and flight trials performed with laser systems operating in the near infrared (NIR) at λ = 1064 nm and λ = 1550 nm. This includes ground tests performed with 10 Hz and 20 KHz PRF NIR laser systems in a variety of atmospheric conditions, and flight trials performed with a 10 Hz airborne NIR laser system installed on a TORNADO aircraft, flying up to altitudes of 22,000 ft above ground level. Future activities are planned to validate the atmospheric retrieval algorithms developed for CO2 column density measurements, with emphasis on aircraft related emissions at airports and other high air-traffic density environments.

  2. Low intensity infrared laser affects expression of oxidative DNA repair genes in mitochondria and nucleus

    NASA Astrophysics Data System (ADS)

    Fonseca, A. S.; Magalhães, L. A. G.; Mencalha, A. L.; Geller, M.; Paoli, F.

    2014-11-01

    Practical properties and physical characteristics of low intensity lasers have made possible their application to treat soft tissue diseases. Excitation of intracellular chromophores by red and infrared radiation at low energy fluences with increase of mitochondrial metabolism is the basis of the biostimulation effect but free radicals can be produced. DNA lesions induced by free radicals are repaired by the base excision repair pathway. In this work, we evaluate the expression of POLγ and APEX2 genes related to repair of mitochondrial and nuclear DNA, respectively. Skin and muscle tissue of Wistar rats were exposed to low intensity infrared laser at different fluences. One hour and 24 hours after laser exposure, tissue samples were withdrawn for total RNA extraction, cDNA synthesis, and evaluation of POLγ and APEX2 mRNA expression by real time quantitative polymerase chain reaction. Skin and muscle tissue of Wistar rats exposed to laser radiation show different expression of POLγ and APEX2 mRNA depending of the fluence and time after exposure. Our study suggests that a low intensity infrared laser affects expression of genes involved in repair of oxidative lesions in mitochondrial and nuclear DNA.

  3. Ocular hazards of tunable continuous-wave near-infrared laser sources

    NASA Astrophysics Data System (ADS)

    Lund, David J.; Edsall, Peter R.; Fuller, Douglas F.; Hoxie, Stephen W.

    1996-04-01

    Retinal damage thresholds (ED50s) were determined in Rhesus monkey eyes for 100 ms exposures to collimated radiation from a tunable Ti:Sapphire laser at several wavelengths from 700 nm to 900 nm. Prior research using 15 ns duration laser pulses showed a strong variability of ED50 with wavelength for retinal exposure in Rhesus monkeys to laser radiation in the near infrared spectrum. Current studies with the Ti:Sapphire laser show similar variability of ED50 with wavelength for 100 ms retinal exposures. Previously measured light transmission and absorption properties of ocular tissues do not provide a complete or obvious explanation for the significant variations of threshold with small changes in wavelength. Similar wavelength dependencies of ED50 for the two exposure durations in the wavelength range of 750 nm to 830 nm suggest that linear absorption is a cause of the variability. However, differences in the ED50 curves at other wavelengths show that nonlinear mechanisms also contribute.

  4. [The treatment of neurogenic hyperreflexic bladder dysfunctions in girls with low-intensity laser radiation].

    PubMed

    Kosilov, K V; Itskovich, A I; Orekhov, V R

    1995-01-01

    120 girls were investigated for the efficacy of three methods of treatment: conventional, infrared laser radiation on the projection of the bladder plus He-Ne laser radiation on biologically active points (BAP), red He-Ne laser BAP radiation. All the patients suffered from neurogenic hyperreflexic dysfunctions of the bladder, 99.8% had the diagnosis of vegetovascular dystonia, 94.9% had sympathetic-tonic or mixed patterns. The combined laser exposure brought about the greatest response rate-90.0%. PMID:7785111

  5. Near and medium infrared optical fiber lasers and emerging applications

    NASA Astrophysics Data System (ADS)

    Prudenzano, F.; Mescia, L.; Allegretti, L.; De Sario, M.; D'Orazio, A.; Di Tommaso, A.; Palmisano, T.; Petruzzelli, V.

    2010-02-01

    Laser cavities emitting in the near and medium infrared wavelength range, made of rare earth doped optical fibers and suitable pairs of integrated mirrors, are used in a large number of applications. Nowadays, the efficient employment of near and medium infrared laser beams is largely widespread in the field of m*aterial processing, surgery, directed energy, remote sensing, spectroscopy, imaging, and so on. In a lot of cases, the high conversion efficiency, the excellent beam quality, the compactness and, the good heat dissipation capability make fiber lasers competitive and attractive with respect to other light sources, such as ion-doped crystal and bulk glass lasers, optical parametric oscillators, semiconductor and gas lasers. The paper aims to recall and/or briefly illustrate a few among the numerous strategies recently followed by research laboratories and industries to obtain laser sources based on rare earth doped optical fibres. A recall on the host materials and the dopants employed for their construction, and the corresponding applications is given, too. Moreover, an example of near infrared (NIR) fiber optic laser development, by employing available on market components is illustrated by underlining the possibility to easily obtain high beam quality.

  6. Extended emission wavelength of random dye lasers by exploiting radiative and non-radiative energy transfer

    NASA Astrophysics Data System (ADS)

    Wan Ismail, Wan Zakiah; Goldys, Ewa M.; Dawes, Judith M.

    2016-02-01

    We demonstrate long-wavelength operation (>700 nm) of random dye lasers (using a methylene blue dye) with the addition of rhodamine 6G and titania, enabled by radiative and non-radiative energy transfer. The pump energy is efficiently absorbed and transferred to the acceptors, to support lasing in random dye lasers in the near infrared. The optimum random laser performance with the highest emission intensity and the lowest lasing threshold was achieved for a concentration of methylene blue as the acceptor equal to 6× the concentration of rhodamine 6G (donor). Excessive levels of methylene blue increased the lasing threshold and broadened the methylene blue emission linewidth due to dye quenching from re-absorption. This is due to competition between the donor emission and energy transfer and between absorption loss and fluorescence quenching. The radiative and non-radiative energy transfer is analyzed as a function of the acceptor concentration and pump energy density, with consideration of the spectral overlap. The dependence of the radiative and non-radiative transfer efficiency on the acceptor concentration is obtained, and the energy transfer parameters, including the radiative and non-radiative energy transfer rate constants ( K R and K NR), are investigated using Stern-Volmer analysis. The analysis indicates that radiative energy transfer is the dominant energy transfer mechanism in this system.

  7. Mid-infrared tunable laser based on the Cr:ZnSe active crystal

    NASA Astrophysics Data System (ADS)

    Koranda, Petr; Jelínková, Helena; Nemec, Michal; Šulc, Jan; Doroshenko, Maxim E.; Basiev, Tasoltan T.; Komar, Vitaly K.; Gerasimenko, Andriy S.; Puzikov, Vyacheslav M.; Badikov, V. V.; Badikov, D. V.

    2008-02-01

    Broadly tunable mid-infrared laser sources operated at room-temperature are desired in many technological and medical applications. The aim of the project was to design and construct broadly tunable powerful Cr:ZnSe laser. The investigated Cr:ZnSe various shaped bulk crystals were grown by the Bridgman method or by the floating zone method. The absorption spectrum was measured to be from 1500 to 2000 nm and the emission spectrum was from 2100 to 2800 nm. Three different lasers were utilized for coherent longitudinal pumping of Cr:ZnSe laser, namely flashlamp-pumped Er:YAP laser (generated wavelength 1660 nm), diode-pumped Tm:YLF laser (generated wavelength 1912 nm) and diode-pumped Tm:YAP laser (generated wavelength 1980 nm). The constructed Cr:ZnSe laser operated in pulsed as well as in continuous-wave regime. In the first case the Cr:ZnSe crystal grown by the floating zone method was studied. The maximal output power in continuous-wave regime was 310 mW with the slope-efficiency 73% for the Tm:YAP laser pumping. In the second case the Cr:ZnSe prism grown by the Bridgman method which served simultaneously as laser active medium and intracavity dispersive element was investigated. For the Er:YAP laser pumping the maximal output energy was 20 mJ with the slope-efficiency 36%. The output radiation was tunable in the range from 2050 nm up to 2750 nm. For the Tm:YAP laser pumping the maximal output power in continuous-wave regime was 175 mW with the slope-efficiency 24%. The output radiation was tunable in the interval from 2220 nm up to 2680 nm. The generated radiation beam spatial structure was close to TEM00.

  8. Model polyimide films: Synthesis, characterization, and deposition by resonant infrared laser ablation

    NASA Astrophysics Data System (ADS)

    Dygert, Nicole Leigh

    A new deposition technique for high performance polymer films, resonant infrared laser ablation (RIR-LA) is presented. Ultraviolet laser deposition techniques have been shown to cause decomposition and depolymerization of the deposited polymer films. We hypothesized that the infrared radiation would be a gentler technique compared to ultraviolet radiation and should leave the polymer structure intact. We proposed a technique where a solution-based polymeric precursor is frozen in liquid nitrogen, placed in vacuum chamber, and ablated by a rastered infrared laser beam. Then the ejected material is collected on a substrate forming a thin polymeric film. First we tested the technique on a 15 weight % pyromellitic dianhydride-co-4,4'-oxidianiline (PMDA-ODA) in N-methylpyrrolidinone (NMP), the polymeric precursor to polyimide. PMDA-ODA is converted to polyimide by a thermal cure near 250 °C. Fourier transform infrared spectroscopy results confirmed that the PMDA-ODA was transferred intact and without curing by RIR-LA. Molecular weight studies show that only a small portion of the original molecular weight is lost, allowing for the preservation of strength and structural properties. The technique was then tested with other polymers including polyamide imide and polyether imide. Both polymers were successfully transferred intact with no signs of curing. Polyamide imide boasts an even lower cure temperature than polyimide at only 150°C, illustrating how effective RIR-LA is at avoiding thermal transformations.

  9. Plans for a far-infrared free-electron laser in India

    SciTech Connect

    Krishnagopal, S.; Kumar, V.; Ramamurthi, S.S.

    1995-12-31

    The Centre for Advanced Technology is building the INDUS complex of synchrotron radiation sources. As part of this programme it is also proposed to build a far-infrared free-electron laser oscillator. This will use a microtron injector and a 40 period undulator made of NdFeB permanent magnets, and is designed to law around 200 microns. We discuss details of the FEL design and the present status of experimental activities on this front.

  10. Infrared heterodyne spectroscopy for astronomical purposes. [laser applications

    NASA Technical Reports Server (NTRS)

    Townes, C. H.

    1978-01-01

    Heterodyne infrared astronomy was carried out using CO2 lasers and some solid state tunable lasers. The best available detectors are mercury cadmium telluride photodiodes. Their quantum efficiencies reach values near 0.5 and in an overall system an effective quantum efficiency, taking into account optical losses and amplifier noise, of about 0.25 was demonstrated. Initial uses of 10 micron heterodyne spectroscopy were for the study of planetary molecular spectra.

  11. Advanced optic fabrication using ultrafast laser radiation

    NASA Astrophysics Data System (ADS)

    Taylor, Lauren L.; Qiao, Jun; Qiao, Jie

    2016-03-01

    Advanced fabrication and finishing techniques are desired for freeform optics and integrated photonics. Methods including grinding, polishing and magnetorheological finishing used for final figuring and polishing of such optics are time consuming, expensive, and may be unsuitable for complex surface features while common photonics fabrication techniques often limit devices to planar geometries. Laser processing has been investigated as an alternative method for optic forming, surface polishing, structure writing, and welding, as direct tuning of laser parameters and flexible beam delivery are advantageous for complex freeform or photonics elements and material-specific processing. Continuous wave and pulsed laser radiation down to the nanosecond regime have been implemented to achieve nanoscale surface finishes through localized material melting, but the temporal extent of the laser-material interaction often results in the formation of a sub-surface heat affected zone. The temporal brevity of ultrafast laser radiation can allow for the direct vaporization of rough surface asperities with minimal melting, offering the potential for smooth, final surface quality with negligible heat affected material. High intensities achieved in focused ultrafast laser radiation can easily induce phase changes in the bulk of materials for processing applications. We have experimentally tested the effectiveness of ultrafast laser radiation as an alternative laser source for surface processing of monocrystalline silicon. Simulation of material heating associated with ultrafast laser-material interaction has been performed and used to investigate optimized processing parameters including repetition rate. The parameter optimization process and results of experimental processing will be presented.

  12. Terahertz radiation from a laser plasma filament.

    PubMed

    Wu, H-C; Meyer-Ter-Vehn, J; Ruhl, H; Sheng, Z-M

    2011-03-01

    By the use of two-dimensional particle-in-cell simulations, we clarify the terahertz (THz) radiation mechanism from a plasma filament formed by an intense femtosecond laser pulse. The nonuniform plasma density of the filament leads to a net radiating current for THz radiation. This current is mainly located within the pulse and the first cycle of the wakefield. As the laser pulse propagates, a single-cycle and radially polarized THz pulse is constructively built up forward. The single-cycle shape is mainly due to radiation damping effect. PMID:21517604

  13. Low-intensity red and infrared lasers on XPA and XPC gene expression

    NASA Astrophysics Data System (ADS)

    Fonseca, A. S.; Magalhães, L. A. G.; Mencalha, A. L.; Ferreira-Machado, S. C.; Geller, M.; Paoli, F.

    2014-09-01

    Laser devices emit monochromatic, coherent, and highly collimated intense beams of light that are useful for a number of biomedical applications. However, for low-intensity lasers, possible adverse effects of laser light on DNA are still controversial. In this work, the expression of XPA and XPC genes in skin and muscle tissue exposed to low-intensity red and infrared lasers was evaluated. Skin and muscle tissue of Wistar rats were exposed to low-intensity red and infrared lasers at different fluences in continuous mode emission. Skin and muscle tissue samples were withdrawn for total RNA extraction, cDNA synthesis, and evaluation of actin gene expression by quantitative polymerase chain reaction. Data obtained show that laser radiation alters the expression of XPA and XPC mRNA differently in skin and muscle tissue of Wistar rats, depending on physical (fluence and wavelength) and biological (tissue) parameters. Laser light could modify expression of genes related to the nucleotide excision repair pathway at fluences and wavelengths used in clinical protocols.

  14. Decomposition of NO studied by infrared emission and CO laser absorption

    NASA Technical Reports Server (NTRS)

    Hanson, R. K.; Flower, W. L.; Monat, J. P.; Kruger, C. H.

    1974-01-01

    A diagnostic technique for monitoring the concentration of NO using absorption of CO laser radiation was developed and applied in a study of the decomposition kinetics of NO. Simultaneous measurements of infrared emission by NO at 5.3 microns were also made to validate the laser absorption technique. The data were obtained behind incident shocks in NO-N2O-Ar (or Kr) mixtures, with temperatures in the range 2400-4100 K. Rate constants for dominant reactions were inferred from comparisons with computer simulations of the reactive flow.

  15. Detecting radiation reaction at moderate laser intensities.

    PubMed

    Heinzl, Thomas; Harvey, Chris; Ilderton, Anton; Marklund, Mattias; Bulanov, Stepan S; Rykovanov, Sergey; Schroeder, Carl B; Esarey, Eric; Leemans, Wim P

    2015-02-01

    We propose a new method of detecting radiation reaction effects in the motion of particles subjected to laser pulses of moderate intensity and long duration. The effect becomes sizable for particles that gain almost no energy through the interaction with the laser pulse. Hence, there are regions of parameter space in which radiation reaction is actually the dominant influence on charged particle motion. PMID:25768626

  16. Laser mode complexity analysis in infrared waveguide free-electron lasers

    NASA Astrophysics Data System (ADS)

    Prazeres, Rui

    2016-06-01

    We analyze an optical phenomenon taking place in waveguide free-electron lasers, which disturbs, or forbids, operation in far infrared range. Waveguides in the optical cavity are used in far-infrared and THz ranges in order to avoid diffraction optical losses, and a hole coupling on output mirror is used for laser extraction. We show that, when the length of the waveguide exceeds a given limit, a phenomenon of "mode disorder" appears in the cavity, which makes the laser difficult, or impossible, to work properly. This phenomenon is even more important when the waveguide covers the whole length of the cavity. A numerical simulation describes this effect, which creates discontinuities of the laser power in the spectral domain. We show an example with an existing infrared Free-Electron Laser, which exhibits such discontinuities of the power, and where no convincing explanation was proposed until now.

  17. Anomalous dispersion and the pumping of far infrared (FIR) lasers

    NASA Technical Reports Server (NTRS)

    Lawandy, N. M.

    1978-01-01

    It is shown that the anomalous dispersion at the pump transition in molecular far-infrared lasers (FIR) can lead to sizable focusing and defocusing effects. Criteria for beam spreading and trapping are considered with CH2F as an example.

  18. Vital parameters related low level laser radiation

    NASA Astrophysics Data System (ADS)

    Palmieri, Beniamino; Capone, Stefania

    2011-08-01

    The first work hypotesis is that biosensors on the patient detecting heart, breath rate and skin parameters, modulate laser radiation to enhance the therapeutic outcome; in the second work hypotesis: biofeedback could be effective, when integrated in the low level laser energy release.

  19. The interaction of infrared radiation with the eye: A review of the literature

    NASA Technical Reports Server (NTRS)

    Turner, H. S.

    1972-01-01

    A compilation of data concerning the effects of infrared radiation on the eye is presented. Information in the following areas is included: (1) transmission and absorption of infrared radiation by the ocular tissues, (2) range of infrared radiation which is harmful to the ocular tissues, (3) infrared radiation thresholds of the various oscular tissues, and (4) infrared radiation transmission and absorption of current optic materials.

  20. Nd:YAG laser systems with radiation delivery by thin hollow waveguides

    NASA Astrophysics Data System (ADS)

    Nemec, Michal; Jelínková, Helena; Šulc, Jan; Miyagi, Mitsunobu; Iwai, Katsumasa; Shi, Yi-Wei; Matsuura, Yuji

    2008-04-01

    The goal of the work was the investigation of hollow waveguide utilization for near infrared laser radiation delivery. As basic delivery unit, a new thin cyclic olefin polymer coated silver hollow glass waveguide with diameters 100/190 μm or 250/360 μm and length up to 20 cm was used. Four near infrared laser sources were based on the Nd:YAG crystals. The first one - Nd:YAG laser passively Q-switched by LiF:F 2- saturable absorber - was coherently pumped by Alexandrite radiation. The system generated 1.06 μm wavelength radiation with 6 ns length of pulse and 0.7 mJ maximum output energy. The second and third laser systems were compact longitudinally diode pumped Nd:YAG lasers generating radiation at wavelength 1.06 μm and 1.44 μm. These lasers were operating in a free-running regime under pulsed pumping (pulse repetition rate 50 Hz). Mean output power 160 mW (90 mW) with pulse length 0.5 ms (1 ms) was generated at wavelength 1.06 μm (1.44 μm). The last radiation source was the Nd:YAG/V:YAG microchip laser pumped by laser diode and generating the radiation at 1.34 μm wavelength. The output power, pulse length, and repetition rate were 25 mW, 6 ns, and 250 Hz, respectively. All lasers were generating beam with gaussian TEM 00 profile. These radiations were focused into thin a waveguide and delivery radiation characteristics were investigated. It was recognized that the output spatial structure is significantly modified in all cases. However a compact delivery system can be useful for near infrared powerful radiation delivery in some special technological and medical applications.

  1. Mid-infrared spatial filter fabrication using laser chemical etching

    NASA Astrophysics Data System (ADS)

    Drouet D'Aubigny, Christian Y.; Walker, Christopher K.; Golish, Dathon R.

    2004-10-01

    Feedhorns like those commonly used in radio-telescope and radio communication equipment couple very efficiently (>98%) to the fundamental Gaussian mode (TEM00). High order modes are not propagated through a single-mode hollow metallic waveguides. It follows that a back to back feedhorn design joined with a small length of single-mode waveguide can be used as a very high throughput spatial filter. Laser micro machining provides a mean of scaling successful waveguide and quasi-optical components to far and mid infrared wavelengths. A laser micro machining system optimized for THz and far IR applications has been in operation at Steward Observatory for several years and produced devices designed to operate at λ=60μm. A new laser micromachining system capable of producing mid-infrared devices will soon be operational. These proceedings review metallic hollow waveguide spatial filtering theory, feedhorn designs as well as laser chemical etching and the design of a new high-NA UV laser etcher capable of sub-micron resolution to fabricate spatial filters for use in the mid-infrared.

  2. Optimized laser application in dermatology using infrared thermography

    NASA Astrophysics Data System (ADS)

    Thomas, Roderick A.; Donne, Kelvin E.; Clement, Marc; Kiernan, Michael N.

    2002-03-01

    Infrared thermography can be used to optimize the application of lasers in dermatology with particular reference to the treatment of certain skin disorders such as vascular lesions and depilation. The efficacy of treatment is dependent upon a number of factors including: Optimization and correct selection of laser parameters such as wavelength and spot size. Human factors, such as laser operator skill, patient's skin type and anatomical location. By observing the thermal effects of laser irradiation on the skins surface during treatment results in improved efficacy and minimizes the possible threshold to skin damage, reducing the possibility of burning and scarring. This is of particular significance for example, in the control of purpura for the treatment of vascular lesions. The optimization is validated with reference to a computer model that predicts various skin temperatures based on two different laser spot sizes.

  3. Radiation Degradation Mechanisms in Laser Diodes

    NASA Technical Reports Server (NTRS)

    Johston, A. H.; Miyahira, T. F.

    2004-01-01

    Degradation mechanisms are investigated for laser diodes fabricated with different materials and wavelengths between 660 and 1550 nm. A new approach is developed that evaluates degradation below the laser threshold to determine the radiation-induced recombination density. This allows mechanisms at high injection, such as Auger recombination, to be separated from low-injection damage. New results show that AlGaInP lasers in the visible region are nearly an order of magnitude more resistant to radiation than devices fabricated with AlGaAs or AlGaAsP at longer wavelengths.

  4. In vivo studies of ultrafast near-infrared laser tissue bonding and wound healing

    NASA Astrophysics Data System (ADS)

    Sriramoju, Vidyasagar; Alfano, Robert R.

    2015-10-01

    Femtosecond (fs) pulse lasers in the near-infrared (NIR) range exhibit very distinct properties upon their interaction with biomolecules compared to the corresponding continuous wave (CW) lasers. Ultrafast NIR laser tissue bonding (LTB) was used to fuse edges of two opposing animal tissue segments in vivo using fs laser photoexcitation of the native vibrations of chomophores. The fusion of the incised tissues was achieved in vivo at the molecular level as the result of the energy-matter interactions of NIR laser radiation with water and the structural proteins like collagen in the target tissues. Nonthermal vibrational excitation from the fs laser absorption by water and collagen induced the formation of cross-links between tissue proteins on either sides of the weld line resulting in tissue bonding. No extrinsic agents were used to facilitate tissue bonding in the fs LTB. These studies were pursued for the understanding and evaluation of the role of ultrafast NIR fs laser radiation in the LTB and consequent wound healing. The fs LTB can be used for difficult to suture structures such as blood vessels, nerves, gallbladder, liver, intestines, and other viscera. Ultrafast NIR LTB yields promising outcomes and benefits in terms of wound closure and wound healing under optimal conditions.

  5. Trace gas monitoring with infrared laser-based detection schemes

    NASA Astrophysics Data System (ADS)

    Sigrist, M. W.; Bartlome, R.; Marinov, D.; Rey, J. M.; Vogler, D. E.; Wächter, H.

    2008-02-01

    The success of laser-based trace gas sensing techniques crucially depends on the availability and performance of tunable laser sources combined with appropriate detection schemes. Besides near-infrared diode lasers, continuously tunable midinfrared quantum cascade lasers and nonlinear optical laser sources are preferentially employed today. Detection schemes are based on sensitive absorption measurements and comprise direct absorption in multi-pass cells as well as photoacoustic and cavity ringdown techniques in various configurations. We illustrate the performance of several systems implemented in our laboratory. These include time-resolved multicomponent traffic emission measurements with a mobile CO2-laser photoacoustic system, a diode-laser based cavity ringdown device for measurements of impurities in industrial process control, isotope ratio measurements with a difference frequency (DFG) laser source combined with balanced path length detection, detection of methylamines for breath analysis with both a near-IR diode laser and a DFG source, and finally, acetone measurements with a heatable multipass cell intended for vapor phase studies on doping agents in urine samples.

  6. Dichromatic laser radiation effects on DNA of Escherichia coli and plasmids

    NASA Astrophysics Data System (ADS)

    Martins, W. A.; Polignano, G. A. C.; Guimarães, O. R.; Geller, M.; Paoli, F.; Fonseca, A. S.

    2015-04-01

    Dichromatic and consecutive laser radiations have attracted increased attention for clinical applications as offering new tools for the treatment of dysfunctional tissues in situations where monochromatic radiation is not effective. This work evaluated the survival, filamentation and morphology of Escherichia coli cells, and the induction of DNA lesions, in plasmid DNA exposed to low-intensity consecutive dichromatic laser radiation. Exponential and stationary wild type and formamidopyrimidine DNA glycosylase/MutM protein deficient E. coli cultures were exposed to consecutive low-intensity dichromatic laser radiation (infrared laser immediately after red laser) to study the survival, filamentation and morphology of bacterial cells. Plasmid DNA samples were exposed to dichromatic radiation to study DNA lesions by electrophoretic profile. Dichromatic laser radiation affects the survival, filamentation and morphology of E. coli cultures depending on the growth phase and the functional repair mechanism of oxidizing lesions in DNA, but does not induce single/double strands breaks or alkali-labile DNA lesions. Results show that low-intensity consecutive dichromatic laser radiation induces biological effects that differ from those induced by monochromatic laser radiation, suggesting that other therapeutic effects could be obtained using dichromatic radiation.

  7. The design of infrared laser radar for vehicle initiative safety

    NASA Astrophysics Data System (ADS)

    Gong, Ping; Xu, Xi-ping; Li, Xiao-yu; Li, Tian-zhi; Liu, Yu-long; Wu, Jia-hui

    2013-09-01

    Laser radar for vehicle is mainly used in advanced vehicle on-board active safety systems, such as forward anti-collision systems, active collision warning systems and adaptive cruise control systems, etc. Laser radar for vehicle plays an important role in the improvement of vehicle active safety and the reduction of traffic accidents. The stability of vehicle active anti-collision system in dynamic environment is still one of the most difficult problems to break through nowadays. According to people's driving habit and the existed detecting technique of sensor, combining the infrared laser range and galvanometer scanning technique , design a 3-D infrared laser radar which can be used to assist navigation, obstacle avoidance and the vehicle's speed control for the vehicle initiative safety. The device is fixed to the head of vehicle. Then if an accident happened, the device could give an alarm to remind the driver timely to decelerate or brake down, by which way can people get the purpose of preventing the collision accidents effectively. To accomplish the design, first of all, select the core components. Then apply Zemax to design the transmitting and receiving optical system. Adopt 1550 nm infrared laser transmitter as emission unit in the device, a galvanometer scanning as laser scanning unit and an InGaAs-APD detector as laser echo signal receiving unit. Perform the construction of experimental system using FPGA and ARM as the core controller. The system designed in this paper can not only detect obstacle in front of the vehicle and make the control subsystem to execute command, but also transfer laser data to PC in real time. Lots of experiments using the infrared laser radar prototype are made, and main performance of it is under tested. The results of these experiments show that the imaging speed of the laser radar can reach up to 25 frames per second, the frame resolution of each image can reach 30×30 pixels, the horizontal angle resolution is about 6. 98

  8. Electronic modulation of infrared radiation in graphene plasmonic resonators.

    PubMed

    Brar, Victor W; Sherrott, Michelle C; Jang, Min Seok; Kim, Seyoon; Kim, Laura; Choi, Mansoo; Sweatlock, Luke A; Atwater, Harry A

    2015-01-01

    All matter at finite temperatures emits electromagnetic radiation due to the thermally induced motion of particles and quasiparticles. Dynamic control of this radiation could enable the design of novel infrared sources; however, the spectral characteristics of the radiated power are dictated by the electromagnetic energy density and emissivity, which are ordinarily fixed properties of the material and temperature. Here we experimentally demonstrate tunable electronic control of blackbody emission from graphene plasmonic resonators on a silicon nitride substrate. It is shown that the graphene resonators produce antenna-coupled blackbody radiation, which manifests as narrow spectral emission peaks in the mid-infrared. By continuously varying the nanoresonator carrier density, the frequency and intensity of these spectral features can be modulated via an electrostatic gate. This work opens the door for future devices that may control blackbody radiation at timescales beyond the limits of conventional thermo-optic modulation. PMID:25948173

  9. Laser action in chromium-activated forsterite for near-infrared excitation: Is Cr/sup 4 +/ the lasing ion

    SciTech Connect

    Petricevic, V.; Gayen, S.K.; Alfano, R.R.

    1988-12-26

    Room-temperature pulsed laser action has been obtained in chromium-activated forsterite (Cr:Mg/sub 2/SiO/sub 4/) for excitation of the near-infrared absorption band of the system by the 1064 nm radiation from a Nd:YAG laser. The characteristics of laser emission are similar to those observed for 532 nm pumping. It is suggested that the laser action is due to a ''center'' other than the trivalent chromium (Cr/sup 3 +/), presumably the tetravalent chromium (Cr/sup 4 +/).

  10. Free-electron laser - far-infrared study of Fef2:Mn. Report No. 1, January 1986-January 1987

    SciTech Connect

    Spector, J.; Kaminski, J.; Jaccarino, V.

    1987-01-01

    The first use of a free-electron laser (FEL) for condensed-matter research was made on iron fluoride:manganese with the far-infrared radiation from the UCSB FEL. The versatility of the FEL for linear and nonequilibrium spectroscopy is demonstrated in studies of the host and impurity modes.

  11. High speed infrared radiation thermometer, system, and method

    DOEpatents

    Markham, James R.

    2002-01-01

    The high-speed radiation thermometer has an infrared measurement wavelength band that is matched to the infrared wavelength band of near-blackbody emittance of ceramic components and ceramic thermal barrier coatings used in turbine engines. It is comprised of a long wavelength infrared detector, a signal amplifier, an analog-to-digital converter, an optical system to collect radiation from the target, an optical filter, and an integral reference signal to maintain a calibrated response. A megahertz range electronic data acquisition system is connected to the radiation detector to operate on raw data obtained. Because the thermometer operates optimally at 8 to 12 .mu.m, where emittance is near-blackbody for ceramics, interferences to measurements performed in turbine engines are minimized. The method and apparatus are optimized to enable mapping of surface temperatures on fast moving ceramic elements, and the thermometer can provide microsecond response, with inherent self-diagnostic and calibration-correction features.

  12. Polarimeter measures sea state characteristics using emitted infrared radiation

    NASA Technical Reports Server (NTRS)

    Egan, W. G.; Hilgeman, T.

    1977-01-01

    An infrared polarimeter, capable of operating between 1 and 12 micrometers wavelength has been used to measure the polarization of emitted radiation from the sea. The observed polarization at 10.6 micrometers from a smooth sea was found to be positive, indicating the dominance of reflected infrared sky radiation over the emitted. With the appearance of waves, the percent polarization increased, as expected, for a zenith angle well above the Brewster angle for water. This is qualitatively in accordance with a model presented to explain the behavior. Initial analyses indicate that the polarized components of the sea's emitted and reflected radiation are affected by type and direction of waves, angle of viewing, and foam. The effects of variations in these parameters require further delineation. The infrared polarimetric technique appears to be a novel new passive method for remote monitoring of waves.

  13. Shifting of infrared radiation using rotational raman resonances in diatomic molecular gases

    DOEpatents

    Kurnit, Norman A.

    1980-01-01

    A device for shifting the frequency of infrared radiation from a CO.sub.2 laser by stimulated Raman scattering in either H.sub.2 or D.sub.2. The device of the preferred embodiment comprises an H.sub.2 Raman laser having dichroic mirrors which are reflective for 16 .mu.m radiation and transmittive for 10 .mu.m, disposed at opposite ends of an interaction cell. The interaction cell contains a diatomic molecular gas, e.g., H.sub.2, D.sub.2, T.sub.2, HD, HT, DT and a capillary waveguide disposed within the cell. A liquid nitrogen jacket is provided around the capillary waveguide for the purpose of cooling. In another embodiment the input CO.sub.2 radiation is circularly polarized using a Fresnel rhomb .lambda./4 plate and applied to an interaction cell of much longer length for single pass operation.

  14. Infrared Radiation Filament And Metnod Of Manufacture

    DOEpatents

    Johnson, Edward A.

    1998-11-17

    An improved IR radiation source is provided by the invention. A radiation filament has a textured surface produced by seeded ion bombardment of a metal foil which is cut to a serpentine shape and mounted in a windowed housing. Specific ion bombardment texturing techniques tune the surface to maximize emissions in the desired wavelength range and to limit emissions outside that narrow range, particularly at longer wavelengths. A combination of filament surface texture, thickness, material, shape and power circuit feedback control produce wavelength controlled and efficient radiation at much lower power requirements than devices of the prior art.

  15. Scanning Laser Infrared Molecular Spectrometer (SLIMS)

    NASA Technical Reports Server (NTRS)

    Scott, David C.; Rickey, Kelly; Ksendzov, Alexander; George, Warren P.; Aljabri, Abdullah S.; Steinkraus, Joel M.

    2012-01-01

    This prototype innovation is a novel design that achieves very long, effective laser path lengths that are able to yield ppb (parts per billion) and sub-ppb measurements of trace gases. SLIMS can also accommodate multiple laser channels covering a wide range of wavelengths, resulting in detection of more chemicals of interest. The mechanical design of the mirror cell allows for the large effective path length within a small footprint. The same design provides a robust structure that lends itself to being immune to some of the alignment challenges that similar cells face. By taking a hollow cylinder and by cutting an elliptically or spherically curved surface into its inner wall, the basic geometry of a reflecting ring is created. If the curved, inner surface is diamond-turned and highly polished, a surface that is very highly reflective can be formed. The surface finish can be further improved by adding a thin chrome or gold film over the surface. This creates a high-quality, curved, mirrored surface. A laser beam, which can be injected from a small bore hole in the wall of the cylinder, will be able to make many low-loss bounces around the ring, creating a large optical path length. The reflecting ring operates on the same principle as the Herriott cell. The difference exists in the mirror that doesn't have to be optically aligned, and which has a relatively large, internal surface area that lends itself to either open air or evacuated spectroscopic measurements. This solid, spherical ring mirror removes the possibility of mirror misalignment caused by thermal expansion or vibrations, because there is only a single, solid reflecting surface. Benefits of the reflecting ring come into play when size constraints reduce the size of the system, especially for space missions in which mass is at a premium.

  16. Investigation of Infra-red and Nonequilibrium Air Radiation

    NASA Technical Reports Server (NTRS)

    Kruger, Charles H.; Laux, Christophe O.

    1994-01-01

    This report summarizes the results obtained during a research program on the infrared radiation of air plasmas conducted in the High Temperature Gasdynamics Laboratory at Stanford University. This program was intended to investigate the masking of infrared signatures by the air plasma formed behind the bow shock of high velocity missiles. Prior to this work, the radiative emission of air plasmas in the infrared had been the object of few experimental investigations, and although several infrared systems were already modeled in radiation codes such as NEQAIR, measurements were required to validate numerical predictions and indicate whether all transitions of importance were accounted for in the model. The program was further motivated by the fact that 9 excited states (A, B, C, D, B', F, H, and H') of NO radiate in the infrared, especially between 1 and 1.5 microns where at least 9 transitions involving can be observed. Because these IR transitions are relatively well separated from each other, excited NO states concentrations can be easily measured, thus providing essential information on excited-state chemistry for use in optical diagnostics or in electronic excitation model validation. Detailed comparisons between measured and simulated spectra are presented.

  17. Infrared radiative energy transfer in gaseous systems

    NASA Technical Reports Server (NTRS)

    Tiwari, Surendra N.

    1991-01-01

    Analyses and numerical procedures are presented to investigate the radiative interactions in various energy transfer processes in gaseous systems. Both gray and non-gray radiative formulations for absorption and emission by molecular gases are presented. The gray gas formulations are based on the Planck mean absorption coefficient and the non-gray formulations are based on the wide band model correlations for molecular absorption. Various relations for the radiative flux and divergence of radiative flux are developed. These are useful for different flow conditions and physical problems. Specific plans for obtaining extensive results for different cases are presented. The procedure developed was applied to several realistic problems. Results of selected studies are presented.

  18. Ultrafast pulses from a mid-infrared fiber laser.

    PubMed

    Hu, Tomonori; Jackson, Stuart D; Hudson, Darren D

    2015-09-15

    Ultrafast laser pulses at mid-infrared wavelengths (2-20 μm) interact strongly with molecules due to the resonance with their vibration modes. This enables their application in frequency comb-based sensing and laser tissue surgery. Fiber lasers are ideal to achieve these pulses, as they are compact, stable, and efficient. We extend the performance of these lasers with the production of 6.4 kW at a wavelength of 2.8 μm with complete electric field retrieval using frequency-resolved optical gating techniques. Contrary to the problems associated with achieving a high average power, fluoride fibers have now shown the capability of operating in the ultrafast, high-peak-power regime. PMID:26371902

  19. Near-Infrared Laser Adjuvant for Influenza Vaccine

    PubMed Central

    Kashiwagi, Satoshi; Yuan, Jianping; Forbes, Benjamin; Hibert, Mathew L.; Lee, Eugene L. Q.; Whicher, Laura; Goudie, Calum; Yang, Yuan; Chen, Tao; Edelblute, Beth; Collette, Brian; Edington, Laurel; Trussler, James; Nezivar, Jean; Leblanc, Pierre; Bronson, Roderick; Tsukada, Kosuke; Suematsu, Makoto; Dover, Jeffrey; Brauns, Timothy; Gelfand, Jeffrey; Poznansky, Mark C.

    2013-01-01

    Safe and effective immunologic adjuvants are often essential for vaccines. However, the choice of adjuvant for licensed vaccines is limited, especially for those that are administered intradermally. We show that non-tissue damaging, near-infrared (NIR) laser light given in short exposures to small areas of skin, without the use of additional chemical or biological agents, significantly increases immune responses to intradermal influenza vaccination without augmenting IgE. The NIR laser-adjuvanted vaccine confers increased protection in a murine influenza lethal challenge model as compared to unadjuvanted vaccine. We show that NIR laser treatment induces the expression of specific chemokines in the skin resulting in recruitment and activation of dendritic cells and is safe to use in both mice and humans. The NIR laser adjuvant technology provides a novel, safe, low-cost, simple-to-use, potentially broadly applicable and clinically feasible approach to enhancing vaccine efficacy as an alternative to chemical and biological adjuvants. PMID:24349390

  20. Laser synchrotron radiation and beam cooling

    SciTech Connect

    Esarey, E.; Sprangle, P.; Ting, A.

    1995-12-31

    The interaction of intense {approx_gt} 10{sup 18} W/cm{sup 2}, short pulse ({approx_lt} 1 ps) lasers with electron beams and plasmas can lead to the generation of harmonic radiation by several mechanisms. Laser synchrotron radiation may provide a practical method for generating tunable, near monochromatic, well collimated, short pulse x-rays in compact, relatively inexpensive source. The mechanism for the generation of laser synchrotron radiation is nonlinear Thomson scattering. Short wavelengths can be generated via Thomson scattering by two methods, (i) backscattering from relativistic electron beams, in which the radiation frequency is upshifted by the relativistic factor 4{gamma}{sup 2}, and (ii) harmonic scattering, in which a multitude of harmonics are generated with harmonic numbers extending out to the critical harmonic number nc{approx_equal}a{sub 0}{sup 3} {much_gt} 1, where a{sub 0} {approx_equal}10{sup -9}{lambda}I{sup 1/2}, {lambda} is the laser wavelength in {mu}m and I is the laser intensity in W/cm{sup 2}. Laser synchrotron sources are capable of generating short ({approx_lt} ps) x-ray pulses with high peak flux ({approx_gt} 10{sup 21} photons/s) and brightness ({approx_gt}{sup 19} photons/s-mm{sup 2}-mrad{sup 2} 0.1%BW. As the electron beam radiates via Thomson scattering, it can subsequently be cooled, i.e., the beam emittance and energy spread can be reduced. This cooling can occur on rapid ({approximately} ps) time scales. In addition, electron distributions with sufficiently small axial energy spreads can be used to generate coherent XUV radiation via a laser-pumped FEL mechanism.

  1. Infrared Laser System for Extended Area Monitoring of Air Pollution

    NASA Technical Reports Server (NTRS)

    Snowman, L. R.; Gillmeister, R. J.

    1971-01-01

    An atmospheric pollution monitoring system using a spectrally scanning laser has been developed by the General Electric Company. This paper will report on an evaluation of a breadboard model, and will discuss applications of the concept to various ambient air monitoring situations. The system is adaptable to other tunable lasers. Operating in the middle infrared region, the system uses retroreflectors to measure average concentrations over long paths at low, safe power levels. The concept shows promise of meeting operational needs in ambient air monitoring and providing new data for atmospheric research.

  2. Tunable Radiation Source by Coupling Laser-Plasma-Generated Electrons to a Periodic Structure

    SciTech Connect

    Jin, Z.; Chen, Z. L.; Kon, A.; Nakatsutsumi, M.; Zhuo, H. B.; Wang, H. B.; Zhang, B. H.; Gu, Y. Q.; Wu, Y. C.; Zhu, B.; Wang, L.; Yu, M. Y.; Sheng, Z. M.; Kodama, R.

    2011-12-23

    Near-infrared radiation around 1000 nm generated from the interaction of a high-density MeV electron beam, obtained by impinging an intense ultrashort laser pulse on a solid target, with a metal grating is observed experimentally. Theoretical modeling and particle-in-cell simulation suggest that the radiation is caused by the Smith-Purcell mechanism. The results here indicate that tunable terahertz radiation with tens GV/m field strength can be achieved by using appropriate grating parameters.

  3. Far infrared radiation (FIR): its biological effects and medical applications

    PubMed Central

    Vatansever, Fatma; Hamblin, Michael R.

    2013-01-01

    Far infrared (FIR) radiation (λ = 3–100 μm) is a subdivision of the electromagnetic spectrum that has been investigated for biological effects. The goal of this review is to cover the use of a further sub-division (3– 12 μm) of this waveband, that has been observed in both in vitro and in vivo studies, to stimulate cells and tissue, and is considered a promising treatment modality for certain medical conditions. Technological advances have provided new techniques for delivering FIR radiation to the human body. Specialty lamps and saunas, delivering pure FIR radiation (eliminating completely the near and mid infrared bands), have became safe, effective, and widely used sources to generate therapeutic effects. Fibers impregnated with FIR emitting ceramic nanoparticles and woven into fabrics, are being used as garments and wraps to generate FIR radiation, and attain health benefits from its effects. PMID:23833705

  4. Processing of polymer surfaces by laser radiation

    NASA Astrophysics Data System (ADS)

    Kreutz, E. W.; Frerichs, H.; Stricker, J.; Wesner, D. A.

    1995-11-01

    The processing of polymer surfaces by laser radiation is investigated as a function of laser parameters (fluence, mode of operation) and processing variables (repetition rate, pulse number). Polymers under investigation are polyamide, polymethylmethacrylate, polypropylene, polystyrene, polycarbonate, acrylonitrile-butadiene-styrene copolymer, styrene-acrylonitrile copolymer, polybutadiene terephtalate, and polyoxymethylene, which are studied in air within different processing regimes such as modification of surface properties for subsequent metallization and removal of material for structuring of surface geometry. The metallization of polymers, which are pretreated by laser irradiation, wet chemical etching or plasma etching, is performed via electroplating and physical vapour deposition as a function of surface properties. The removal of polymers including non-thermal and thermal processes is done by direct processing techniques in the demagnification mode within one processing step. The diagnosis and the modelling of physical processes involved in tailoring the surface properties of polymers with laser radiation have to be implied to improve any application of these materials.

  5. Infrared Laser Optoacoustic Detection Of Gases And Vapours

    NASA Astrophysics Data System (ADS)

    Johnson, S. A.; Cummins, P. G.; Bone, S. A.; Davies, P. B.

    1988-10-01

    Mid-infrared laser optoacoustic spectroscopy has been used to detect a variety of gases and vapours. Performance was calibrated using the signal from a known concentration of ethene, and then the method applied to the perfume alcohol geraniol. Detection limits were found to be 1 ppb for ethene and 70 ppb for geraniol on their strongest absorption lines for a few seconds measurement time.

  6. Infrared Pulsed Laser Deposition: Applications in Photonics and Biomedical Technologies

    NASA Astrophysics Data System (ADS)

    Haglund, Richard

    2006-04-01

    Resonant infrared pulsed-laser deposition (RIR-PLD) shows significant promise for synthesizing thin films of small organic molecules, thermoplastic and thermosetting polymers and biopolymers, without compromising structure or functionality. This contrasts with most attempts at UV-PLD of organic materials, which have often been accompanied by severe photochemical or photothermal degradation of the ablated material. Representative recent successes in RIR-PLD include deposition of: polymers for light emission and hole transport; functionalized polymers and nanoparticles for chemical and biological sensing; and biocompatible polymers suitable for coating medical devices or drug-delivery vehicles. Plume imaging and various other optical- and mass-spectroscopy experiments appear to confirm that polymers or organic molecules ablated by resonant infrared laser irradiation experience a high spatial and temporal density of vibrational excitation, but tend to remain in the electronic ground state. The mechanism of RIR-PLD is observed to depend on the anharmonicity of the mid-infrared absorption modes, their finite relaxation time, mode-specific nonlinear absorption, and rapid changes in polymer viscosity as a function of temperature. Many of the RIR-PLD experiments to date were carried out using a tunable, mid-infrared, picosecond free-electron laser. However, if RIR-PLD is to become a practical tool for making organic thin films, it will be necessary to develop more conventional lasers that can achieve a similar combination of high pulse intensity, low pulse energy, high pulse-repetition frequency and moderate average power. In conclusion, the prospects for developing precisely such table-top RIR-PLD systems will be discussed.

  7. Spectroscopic Study of Terahertz Generation in Mid-Infrared Quantum Cascade Lasers

    NASA Astrophysics Data System (ADS)

    Jiang, Yifan; Vijayraghavan, Karun; Jung, Seungyong; Jiang, Aiting; Kim, Jae Hyun; Demmerle, Frederic; Boehm, Gerhard; Amann, Markus C.; Belkin, Mikhail A.

    2016-02-01

    Terahertz quantum cascade laser sources based on intra-cavity difference-frequency generation are currently the only room-temperature mass-producible diode-laser-like emitters of coherent 1-6 THz radiation. Device performance has improved dramatically over the past few years to reach milliwatt-level power output and broad tuning from 1.2 to 5.9 THz, all at room-temperature. Terahertz output in these sources originates from intersubband optical nonlinearity in the laser active region. Here we report the first comprehensive spectroscopic study of the optical nonlinearity and investigate its dependence on the mid-infrared pump frequencies. Our work shows that the terahertz generation efficiency can vary by a factor of 2 or greater depending on the spectral position of the mid-infrared pumps for a fixed THz difference-frequency. We have also measured for the first time the linewidth for transitions between the lower quantum cascade laser states, which is critical for determining terahertz nonlinearity and predicting optical loss in quantum cascade laser waveguides.

  8. Spectroscopic Study of Terahertz Generation in Mid-Infrared Quantum Cascade Lasers.

    PubMed

    Jiang, Yifan; Vijayraghavan, Karun; Jung, Seungyong; Jiang, Aiting; Kim, Jae Hyun; Demmerle, Frederic; Boehm, Gerhard; Amann, Markus C; Belkin, Mikhail A

    2016-01-01

    Terahertz quantum cascade laser sources based on intra-cavity difference-frequency generation are currently the only room-temperature mass-producible diode-laser-like emitters of coherent 1-6 THz radiation. Device performance has improved dramatically over the past few years to reach milliwatt-level power output and broad tuning from 1.2 to 5.9 THz, all at room-temperature. Terahertz output in these sources originates from intersubband optical nonlinearity in the laser active region. Here we report the first comprehensive spectroscopic study of the optical nonlinearity and investigate its dependence on the mid-infrared pump frequencies. Our work shows that the terahertz generation efficiency can vary by a factor of 2 or greater depending on the spectral position of the mid-infrared pumps for a fixed THz difference-frequency. We have also measured for the first time the linewidth for transitions between the lower quantum cascade laser states, which is critical for determining terahertz nonlinearity and predicting optical loss in quantum cascade laser waveguides. PMID:26879901

  9. DNA repair gene expression in biological tissues exposed to low-intensity infrared laser.

    PubMed

    de Souza da Fonseca, Adenilson; Mencalha, Andre Luiz; Araújo de Campos, Vera Maria; Ferreira Machado, Samara Cristina; de Freitas Peregrino, Antonio Augusto; Geller, Mauro; de Paoli, Flavia

    2013-07-01

    Special properties of laser light have led to its usefulness in many applications in therapy. Excitation of endogenous chromophores in biotissues and generation of free radicals could be involved in its biological effects. DNA lesions induced by free radicals are repaired by base excision repair pathway. In this work, we evaluated the expression of APE1 and OGG1 genes related to repair of DNA lesions induced by free radicals. Skin and muscle tissues of Wistar rats were exposed to low-intensity infrared laser at different fluences and frequencies. After laser exposition of 1 and 24 h, tissue samples were withdrawn for total RNA extraction, cDNA synthesis, and evaluation of APE1 and OGG1 gene expression by quantitative polymerase chain reaction. Data obtained show that laser radiation alters the expression of APE1 and OGG1 mRNA differently in skin and muscle tissues of Wistar rats depending of the fluence, frequency, and time after exposure. Our study suggests that low-intensity infrared laser affects expression of genes involved in repair of DNA lesions by base excision repair pathway. PMID:22941447

  10. Spectroscopic Study of Terahertz Generation in Mid-Infrared Quantum Cascade Lasers

    PubMed Central

    Jiang, Yifan; Vijayraghavan, Karun; Jung, Seungyong; Jiang, Aiting; Kim, Jae Hyun; Demmerle, Frederic; Boehm, Gerhard; Amann, Markus C.; Belkin, Mikhail A.

    2016-01-01

    Terahertz quantum cascade laser sources based on intra-cavity difference-frequency generation are currently the only room-temperature mass-producible diode-laser-like emitters of coherent 1–6 THz radiation. Device performance has improved dramatically over the past few years to reach milliwatt-level power output and broad tuning from 1.2 to 5.9 THz, all at room-temperature. Terahertz output in these sources originates from intersubband optical nonlinearity in the laser active region. Here we report the first comprehensive spectroscopic study of the optical nonlinearity and investigate its dependence on the mid-infrared pump frequencies. Our work shows that the terahertz generation efficiency can vary by a factor of 2 or greater depending on the spectral position of the mid-infrared pumps for a fixed THz difference-frequency. We have also measured for the first time the linewidth for transitions between the lower quantum cascade laser states, which is critical for determining terahertz nonlinearity and predicting optical loss in quantum cascade laser waveguides. PMID:26879901

  11. Heat pump processes induced by laser radiation

    NASA Technical Reports Server (NTRS)

    Garbuny, M.; Henningsen, T.

    1980-01-01

    A carbon dioxide laser system was constructed for the demonstration of heat pump processes induced by laser radiation. The system consisted of a frequency doubling stage, a gas reaction cell with its vacuum and high purity gas supply system, and provisions to measure the temperature changes by pressure, or alternatively, by density changes. The theoretical considerations for the choice of designs and components are dicussed.

  12. Resonant Infrared Pulsed-Laser Deposition of Polymers Using a Free-Electron Laser

    NASA Astrophysics Data System (ADS)

    Johnson, Stephen; Bellmont, Ron; Bubb, Daniel; Haglund, Richard; Schriver, Ken

    2004-11-01

    Thin films of polyethylene glycol and polystyrene have been produced using resonant infrared pulsed-laser deposition (RIR-PLD). The laser used for the experiments was a tunable, high pulse-repetition rate free-electron laser operating in the mid-IR (2.9 - 3.5 im). Transfer of polymers with molecular weights up to 13,000 was accomplished at resonant vibrational frequencies without concomitant fragmentation or other photochemical degradation, in contrast to PLD techniques using ultraviolet lasers. Potential applications for this technique include drug delivery coatings and chemical and biological sensor construction.

  13. UCLA infrared free-electron laser

    NASA Astrophysics Data System (ADS)

    Dodd, James W.; Hartman, Steven C.; Park, Sanghyun; Pellegrini, Claudio; Rosenzweig, James B.; Smolin, J. A.; Barletta, W. A.; Cline, David B.; Cooper, Richard K.; Kolonko, J.; Davis, J. G.; Hairapetian, G.; Joshi, Chand J.; Luhmann, Neville C., Jr.; Ivanchenkov, S. N.; Khlebnikov, A. S.; Varfolomeev, A. A.

    1992-05-01

    A compact 20 MeV linac with an RF laser-driven electron gun will drive a high-gain (10 cm gain length), 10.6 micrometers wavelength FEL amplifier, operating in the SASE mode. FEL physics in the high-gain regime will be studied, including start-up from noise, optical guiding, sidebands, saturation, and superradiance, with emphasis on the effects important for future short wavelength operation of FEL's. The hybrid undulator, designed and built at the Kurchatov Institute of Atomic Energy in the U.S.S.R., has forty periods, each 1.5 cm long. The magnetic material is a hybrid combination of SmCo5 blocks and Nd-Fe-B blocks, with vanadium-permendur yokes. The gap distance between pole-tips is fixed at 5 mm. On axis the peak value of the completed undulator's magnetic field was measured to be 7.3 kGauss (+/- 0.25%). Measurements during the conditioning phase of the RF gun for the electron beam's peak dark-current show 6 mA without the longitudinal magnetic focusing field in the gun and 34 mA with the focusing field active. The peak current from photoemission is calculated to be 200 A.

  14. Resonant infrared pulsed laser deposition of cyclic olefin copolymer films

    SciTech Connect

    Singaravelu, Senthil R.; Klopf, John M.; Schriver, Kenneth E.; Park, HyeKyoung; Kelley, Michael J.; Haglund, Jr., Richard F.

    2013-08-01

    Barrier materials on thin-film organic optoelectronic devices inhibit the uptake of water, oxygen, or environmental contaminants, and fabricating them is a major challenge. By definition, these barrier layers must be insoluble, so the usual routes to polymer- or organic-film deposition by spin coating are not problematic. In this paper, we report comparative studies of pulsed laser deposition of cyclic olefin copolymer (COC), an excellent moisture barrier and a model system for a larger class of protective materials that are potentially useful in organic electronic devices, such as organic light-emitting diodes (OLEDs). Thin films of COC were deposited by resonant and nonresonant infrared pulsed laser ablation of solid COC targets, using a free-electron laser tuned to the 3.43 μm C–H stretch of the COC, and a high-intensity nanosecond Q-switched laser operated at 1064 nm. The ablation craters and deposited films were characterized by scanning-electron microscopy, Fourier-transform infrared spectrometry, atomic-force microscopy, high-resolution optical microscopy, and surface profilometry. Thermal-diffusion calculations were performed to determine the temperature rise induced in the film at the C–H resonant wavelength. The results show that resonant infrared pulsed laser deposition (RIR-PLD) is an effective, low-temperature thin-film deposition technique that leads to evaporation and deposition of intact molecules in homogeneous, smooth films. Nonresonant PLD, on the other hand, leads to photothermal damage, degradation of the COC polymers, and to the deposition only of particulates.

  15. Resonant infrared pulsed laser deposition of cyclic olefin copolymer films

    NASA Astrophysics Data System (ADS)

    Singaravelu, S.; Klopf, J. M.; Schriver, K. E.; Park, H. K.; Kelley, M. J.; Haglund, R. F.

    2014-03-01

    Barrier materials on thin-film organic optoelectronic devices inhibit the uptake of water, oxygen, or environmental contaminants, and fabricating them is a major challenge. By definition, these barrier layers must be insoluble, so the usual routes to polymer- or organic-film deposition by spin coating are not problematic. In this paper, we report comparative studies of pulsed laser deposition of cyclic olefin copolymer (COC), an excellent moisture barrier and a model system for a larger class of protective materials that are potentially useful in organic electronic devices, such as organic light-emitting diodes (OLEDs). Thin films of COC were deposited by resonant and nonresonant infrared pulsed laser ablation of solid COC targets, using a free-electron laser tuned to the 3.43 μm C-H stretch of the COC, and a high-intensity nanosecond Q-switched laser operated at 1064 nm. The ablation craters and deposited films were characterized by scanning-electron microscopy, Fourier-transform infrared spectrometry, atomic-force microscopy, high-resolution optical microscopy, and surface profilometry. Thermal-diffusion calculations were performed to determine the temperature rise induced in the film at the C-H resonant wavelength. The results show that resonant infrared pulsed laser deposition (RIR-PLD) is an effective, low-temperature thin-film deposition technique that leads to evaporation and deposition of intact molecules in homogeneous, smooth films. Nonresonant PLD, on the other hand, leads to photothermal damage, degradation of the COC polymers, and to the deposition only of particulates.

  16. Laser radiation effects on Mycoplasma agalactiae

    NASA Astrophysics Data System (ADS)

    Dinu, Cerasela Z.; Grigoriu, Constantin; Dinescu, Maria; Pascale, Florentina; Popovici, Adrian; Gheorghescu, Lavinia; Cismileanu, Ana; Avram, Eugenia

    2002-08-01

    The biological effects of the laser radiation emitted by the Nd:YAG laser (second harmonic, wavelength 532 nm /fluence 32 mJ/cm2/pulse duration 6 ns) on the Mycoplasma agalactiae bacterium were studied. The radiation was found to intensify the multiplication of the bacteria irradiated in TRIS buffer (0.125 M), without however affecting the proteinic composition of the cell membrane. When the bacteria were irradiated in their growth medium (PPLO broth) being later cultivated on a solid medium (PPLO agar), the exclusive presence of the atypical colonies (granular and T-like ones) was noticed.

  17. Rectenna that converts infrared radiation to electrical energy

    DOEpatents

    Davids, Paul; Peters, David W.

    2016-09-06

    Technologies pertaining to converting infrared (IR) radiation to DC energy are described herein. In a general embodiment, a rectenna comprises a conductive layer. A thin insulator layer is formed on the conductive layer, and a nanoantenna is formed on the thin insulator layer. The thin insulator layer acts as a tunnel junction of a tunnel diode.

  18. SIMULTANEOUS ROUGH RICE DRYING AND DISINFESTATION WITH INFRARED RADIATION

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The objective of this study was to investigate the drying characteristics, milling quality and disinfestation effectiveness of rough rice under infrared (IR) radiation heating. Freshly harvested medium grain rice (M202) samples with low (20.6%) and high (25.0%) moisture contents (MC) were used for ...

  19. Feasibility of Jujube peeling using novel infrared radiation heating technology

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Infrared (IR) radiation heating has a promising potential to be used as a sustainable and effective method to eliminate the use of water and chemicals in the jujube-peeling process and enhance the quality of peeled products. The objective of this study was to investigate the feasibility of use IR he...

  20. Quality Characteristics of Dried Bananas Produced with Infrared Radiation Technology

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Browning of fruits during drying is a major quality concern. The enzyme polyphenol oxidase has been found to be the main cause of browning in bananas. Infrared radiation (IR) drying could be used to minimize enzymatic browning hence eliminating the need for pre-treatments. This study was to inves...

  1. Dynamics of photoprocesses induced by femtosecond infrared radiation in free molecules and clusters of iron pentacarbonyl

    NASA Astrophysics Data System (ADS)

    Kompanets, V. O.; Lokhman, V. N.; Poydashev, D. G.; Chekalin, S. V.; Ryabov, E. A.

    2016-04-01

    The dynamics of photoprocesses induced by femtosecond infrared radiation in free Fe(CO)5 molecules and their clusters owing to the resonant excitation of vibrations of CO bonds in the 5-μm range has been studied. The technique of infrared excitation and photoionization probing (λ = 400 nm) by femtosecond pulses has been used in combination with time-of-flight mass spectrometry. It has been found that an infrared pulse selectively excites vibrations of CO bonds in free molecules, which results in a decrease in the yield of the Fe(CO)5 + molecular ion. Subsequent relaxation processes have been analyzed and the results have been interpreted. The time of the energy transfer from excited vibrations to other vibrations of the molecule owing to intramolecular relaxation has been measured. The dynamics of dissociation of [Fe(CO)5] n clusters irradiated by femtosecond infrared radiation has been studied. The time dependence of the yield of free molecules has been measured under different infrared laser excitation conditions. We have proposed a model that well describes the results of the experiment and makes it possible, in particular, to calculate the profile of variation of the temperature of clusters within the "evaporation ensemble" concept. The intramolecular and intracluster vibrational relaxation rates in [Fe(CO)5] n clusters have been estimated.

  2. Search for the Cosmic Infrared Background Radiation using COBE Data

    NASA Technical Reports Server (NTRS)

    Hauser, Michael

    2001-01-01

    This project was initiated to allow completion of the primary investigation of the Diffuse Infrared Background Experiment (DIRBE) on NASA's Cosmic Background Explorer (CORE) mission, and to study the implications of those findings. The Principal Investigator (PI) on this grant was also the Principal Investigator on the DIRBE team. The project had two specific goals: Goal 1: Seek improved limits upon, or detections of, the cosmic infrared background radiation using data from the COBE Diffuse Infrared Background Experiment (DIRBE). Goal 2: Explore the implications of the limits and measured values of the cosmic infrared background for energy releases in the Universe since the formation of the first luminous sources. Both of these goals have been successfully accomplished.

  3. Fabrication and spectral tuning of standing gold infrared antennas using single fs-laser pulses.

    PubMed

    Reininghaus, Martin; Wortmann, Dirk; Cao, Zhao; Hoffmann, Jón Mattis; Taubner, Thomas

    2013-12-30

    Upright standing gold monopole nanoantennas are fabricated by irradiation of thin gold films with single pulses of fs-laser radiation. The resulting antennas exhibit extinction resonances in the mid infrared spectral rage for p-polarized light under grazing incidence. Due to the free charge carriers in the surrounding gold film of the antenna, the resonance condition of the thin-wire monopole antenna can be explained by introducing image charges yielding an observable resonance wavelength of four times the antenna length. The antenna length is controlled coarsely by the focusing numerical aperture and fine by the pulse energy of the laser pulse producing the structure. An additional ultrafine tuning of the resonance wavelength with a sub-10 nm resolution is realized by an additional coating process subsequent to the laser structuring. PMID:24514811

  4. Bi-directional terahertz-to-infrared emission from metal-coated nanostructures upon femtosecond laser irradiation.

    PubMed

    Zhang, Liangliang; Wu, Tong; Zhao, Ji; Zhang, Cunlin; Zhang, X-C

    2015-09-21

    We report on the investigation of bi-directional terahertz-to-infrared (THz-to-IR) radiation from a metal film coated on a substrate with randomly ordered pore arrays by irradiation of femtosecond laser pulses. THz-to-IR radiation was observed both for front-side excitation (laser incident on the metal surface) and for rear-side excitation (laser incident on the substrate). In both cases, the radiation was observed both in the propagation direction of the laser beam and in the reverse direction. Considering these findings, we propose a thermal emission mechanism based on the production of surface plasmons, either delocalized (through phase-matched excitation) or localized (through surface roughness) at the air/metal and metal/substrate interfaces. PMID:26406717

  5. Thermodynamic response of soft biological tissues to pulsed infrared-laser irradiation.

    PubMed Central

    Venugopalan, V; Nishioka, N S; Mikić, B B

    1996-01-01

    The physical mechanisms that achieve tissue removal through the delivery of short pulses of high-intensity infrared laser radiation, in a process known as laser ablation, remain obscure. The thermodynamic response of biological tissue to pulsed infrared laser irradiation was investigated by measuring and analyzing the stress transients generated by Q-sw Er:YSGG (lambda = 2.79 microns) and TEA CO2 (lambda = 10.6 microns) laser irradiation of porcine dermis using thin-film piezoelectric transducers. For radiant exposures that do not produce material removal, the stress transients are consistent with thermal expansion of the tissue samples. The temporal structure of the stress transients generated at the threshold radiant exposure for ablation indicates that the onset of material removal is delayed with respect to irradiation. Once material removal is achieved, the magnitude of the peak compressive stress and its variation with radiant exposure are consistent with a model that considers this process as an explosive event occurring after the laser pulse. This mechanism is different from ArF- and KrF-excimer laser ablation where absorption of ultraviolet radiation by the collagenous tissue matrix leads to tissue decomposition during irradiation and results in material removal via rapid surface vaporization. It appears that under the conditions examined in this study, explosive boiling of tissue water is the process that mediates the ablation event. This study provides evidence that the dynamics and mechanism of tissue ablation processes can be altered by targeting tissue water rather than the tissue structural matrix. Images FIGURE 6 PMID:8744336

  6. Research of infrared laser based pavement imaging and crack detection

    NASA Astrophysics Data System (ADS)

    Hong, Hanyu; Wang, Shu; Zhang, Xiuhua; Jing, Genqiang

    2013-08-01

    Road crack detection is seriously affected by many factors in actual applications, such as some shadows, road signs, oil stains, high frequency noise and so on. Due to these factors, the current crack detection methods can not distinguish the cracks in complex scenes. In order to solve this problem, a novel method based on infrared laser pavement imaging is proposed. Firstly, single sensor laser pavement imaging system is adopted to obtain pavement images, high power laser line projector is well used to resist various shadows. Secondly, the crack extraction algorithm which has merged multiple features intelligently is proposed to extract crack information. In this step, the non-negative feature and contrast feature are used to extract the basic crack information, and circular projection based on linearity feature is applied to enhance the crack area and eliminate noise. A series of experiments have been performed to test the proposed method, which shows that the proposed automatic extraction method is effective and advanced.

  7. Investigation of jewelry powders radiating far-infrared rays and the biological effects on human skin.

    PubMed

    Yoo, B H; Park, C M; Oh, T J; Han, S H; Kang, H H; Chang, I S

    2002-01-01

    Far-infrared rays have certain kinds of effects on the human body, especially on skin, blood circulation, and skin cell vitalizing. Some jewelry powders radiate far-infrared rays. Jade has powerful far-infrared ray radiation, and tourmaline has pyroelectric and piezoelectric properties and radiated far-infrared rays. The jewelry powders (fine powdered jade and tourmaline powders) were screened by far-infrared rays for radiation properties and tested for the effects of far-infrared rays on the human skin by temperature observation using an infrared thermal analyzer. PMID:12053208

  8. Infrared Radiography: Modeling X-ray Imaging Without Harmful Radiation

    NASA Astrophysics Data System (ADS)

    Zietz, Otto; Mylott, Elliot; Widenhorn, Ralf

    2015-01-01

    Planar x-ray imaging is a ubiquitous diagnostic tool and is routinely performed to diagnose conditions as varied as bone fractures and pneumonia. The underlying principle is that the varying attenuation coefficients of air, water, tissue, bone, or metal implants within the body result in non-uniform transmission of x-ray radiation. Through the detection of transmitted radiation, the spatial organization and composition of materials in the body can be ascertained. In this paper, we describe an original apparatus that teaches these concepts by utilizing near infrared radiation and an up-converting phosphorescent screen to safely probe the contents of an opaque enclosure.

  9. Infrared

    NASA Astrophysics Data System (ADS)

    Vollmer, M.

    2013-11-01

    underlying physics. There are now at least six different disciplines that deal with infrared radiation in one form or another, and in one or several different spectral portions of the whole IR range. These are spectroscopy, astronomy, thermal imaging, detector and source development and metrology, as well the field of optical data transmission. Scientists working in these fields range from chemists and astronomers through to physicists and even photographers. This issue presents examples from some of these fields. All the papers—though some of them deal with fundamental or applied research—include interesting elements that make them directly applicable to university-level teaching at the graduate or postgraduate level. Source (e.g. quantum cascade lasers) and detector development (e.g. multispectral sensors), as well as metrology issues and optical data transmission, are omitted since they belong to fundamental research journals. Using a more-or-less arbitrary order according to wavelength range, the issue starts with a paper on the physics of near-infrared photography using consumer product cameras in the spectral range from 800 nm to 1.1 µm [1]. It is followed by a series of three papers dealing with IR imaging in spectral ranges from 3 to 14 µm [2-4]. One of them deals with laboratory courses that may help to characterize the IR camera response [2], the second discusses potential applications for nondestructive testing techniques [3] and the third gives an example of how IR thermal imaging may be used to understand cloud cover of the Earth [4], which is the prerequisite for successful climate modelling. The next two papers cover the vast field of IR spectroscopy [5, 6]. The first of these deals with Fourier transform infrared spectroscopy in the spectral range from 2.5 to 25 µm, studying e.g. ro-vibrational excitations in gases or optical phonon interactions within solids [5]. The second deals mostly with the spectroscopy of liquids such as biofuels and special

  10. Continuous-wave vs. pulsed infrared laser stimulation of the rat prostate cavernous nerves

    NASA Astrophysics Data System (ADS)

    Tozburun, Serhat; Cilip, Christopher M.; Lagoda, Gwen A.; Burnett, Arthur L.; Fried, Nathaniel M.

    2011-03-01

    Optical nerve stimulation has recently been developed as an alternative to electrical nerve stimulation. However, recent studies have focused primarily on pulsed delivery of the laser radiation and at relatively low pulse rates. The objective of this study is to demonstrate faster optical stimulation of the prostate cavernous nerves using continuouswave (CW) infrared laser radiation, for potential diagnostic applications. A Thulium fiber laser (λ = 1870 nm) was used for non-contact optical stimulation of the rat prostate cavernous nerves, in vivo. Optical nerve stimulation, as measured by an intracavernous pressure (ICP) response in the penis, was achieved with the laser operating in either CW mode, or with a 5-ms pulse duration at 10, 20, 30, 40, 50, and 100 Hz. Successful optical stimulation was observed to be primarily dependent on a threshold nerve temperature (42-45 °C), not an incident fluence, as previously reported. CW optical nerve stimulation provides a significantly faster ICP response time using a laser with lower power output than pulsed stimulation. CW optical nerve stimulation may therefore represent an alternative mode of stimulation for intra-operative diagnostic applications where a rapid response is critical, such as identification of the cavernous nerves during prostate cancer surgery.

  11. Modeling and analyzing characteristics of self-infrared radiation on airplane-skin

    NASA Astrophysics Data System (ADS)

    Li, Zhaozhao; Wu, Wenyuan; Wu, Chengguo; Yang, Yuntao; Huang, Yanhua; Sunxiaobo, Zhuan

    2016-01-01

    The characteristic of the self-infrared radiation of airplane-skin is very important for the stealth performance of airplane. Based on the theory of the airplane-skin temperature field, the distribution of the atmospheric temperature field and the principle of the black-body radiation function the self-infrared radiation model was established. In specified flight conditions, the influence of the atmospheric temperature, the speed of flight, the emissivity and the sight angle detection on the self-infrared radiation of the airplane skin were analyzed. Through the simulation of infrared radiation, some results under different flight states are obtained. The simulation results show that skin infrared radiation energy mainly concentrate on the far infrared wavebands, and various factors have different effects on the infrared radiation of skin. This conclusion can help reduce the infrared radiation and improve the stealth performance of airplane in the engineering design and the selection of flight conditions.

  12. Laser scan microscope and infrared laser scan microcope: two important tools for device testing

    NASA Astrophysics Data System (ADS)

    Ziegler, Eberhard

    1991-03-01

    The optical beam induced current (OBIC) produced in devices by a laser scan microscope (LSM) is used to localize hot spots, leakage currents, electrostatic discharge defects and weak points. The LSM also allows photoluminescence measurements with high spatial and energy resolution. Using the infrared laser scan microscope (IR LSM), defects in the metallization and latch-up sensitive region could be detected from the back of the device.

  13. A novel laser angioplasty guided hollow fiber using mid-infrared laser

    NASA Astrophysics Data System (ADS)

    Yoshihashi-Suzuki, Sachiko; Yamada, Shinya; Sato, Izuru; Awazu, Kunio

    2006-02-01

    We have proposed selective removal of cholesterol ester by infrared laser of wavelength with 5.75 μm irradiation; the wavelength of 5.75 μm correspond with the ester bond C=O stretching vibration. The flexible laser guiding line and a compact light source are required for our proposal. We used a compact mid-infrared tunable laser by difference frequency generation; DFG laser was developed for substitute light source of free electron laser. In the present work, first, we have developed hollow optical fiber with a diamond lens-tip to deliver DFG laser in the blood vessel and evaluated the transmission of DFG laser from 5.5 μm to 7.5 μm. The transmission of 5.75 μm is about 65%, the DFG beam was focused on the tip of fiber by diamond lens-tip. Secondly, we performed the selective removal experiment of cholesterol ester using the hollow optical fiber with diamond lens-tip and DFG laser. The sample used a two layer model, cholesterol oleate and gelatin. The cholesterol oleate was decomposed by 5.75 μm DFG irradiation with 3.8 W/cm2.

  14. Radiation drive in laser heated hohlraums

    SciTech Connect

    Suter, L.J.; Kauffman, R.L.; Darrow, C.B.

    1995-11-03

    Nearly 10 years of Nova experiments and analysis have lead to a relatively detailed quantitative and qualitative understanding of radiation drive in laser heated hohlraums. Our most successful quantitative modelling tool is 2D Lasnex numerical simulations. Analysis of the simulations provides us with insight into the details of the hohlraum drive. In particular we find hohlraum radiation conversion efficiency becomes quite high with longer pulses as the accumulated, high Z blow-off plasma begins to radiate. Extensive Nova experiments corroborate our quantitative and qualitative understanding.

  15. Development of Mid-Infrared Lasers for the Measurement of Trace Atmospheric Gases

    NASA Astrophysics Data System (ADS)

    Hannun, R. A.; Witinski, M. F.; Forouhar, S.; Anderson, J.

    2012-12-01

    In order to thoroughly characterize atmospheric composition at all altitudes, an unprecedented scientific and technical effort is needed. Essential to the advancement of both satellite and in situ science are improvements in continuous wave (CW) and high-power pulsed laser systems in the infrared spectral region integrated with miniaturized electronic and optical components, allowing for the deployment of single mode light sources aboard satellite and UAV platforms. Sources in the the spectral region from 2.8 μm to 3.5 μm are crucial to the sensitive and precise quantification of several atmospherically relevant species, including: OH, H2O, H218O, HDO, CH4, 13CH4, CO2, CH2O, and C2H6, all of which present strong fundamental vibrational absorptions in this mid-infrared range. Currently, however, a massive technology gap exists in both CW and pulsed laser systems within this spectral window. Recent developments include the advancement of CW tunable diode technology using new solid state materials to improve electron hole localization, and the initial integration of these lasers into miniaturized optoelectronic systems ideal for in situ deployment. In addition, high-power pulsed light sources have been produced using optical parametric generation (OPG). A single-frequency Nd:YAG pumps a nonlinear crystal, injection seeded with a diode laser to enhance efficiency and reduce the bandwidth of the output radiation, creating a light source ideal for LIDAR and other remote sensing applications.

  16. Ablation of crystalline oxides by infrared femtosecond laser pulses

    SciTech Connect

    Watanabe, Fumiya; Cahill, David G.; Gundrum, Bryan; Averback, R. S.

    2006-10-15

    We use focused laser pulses with duration of 180 fs and wavelength of 800 nm to study the interactions of high power near-infrared light with the surfaces of single-crystal transparent oxides (sapphire, LaAlO{sub 3}, SrTiO{sub 3}, yttria-stabilized ZrO{sub 2}, and MgO); the morphologies of the ablation craters are studied by atomic force microscopy and scanning electron microscopy. With the exception of LaAlO{sub 3}, the high temperature annealing of these oxide crystals produces atomically flat starting surfaces that enable studies of the morphology of ablation craters with subnanometer precision. The threshold fluence for ablation is determined directly from atomic-force microscopy images and increases approximately linearly with the band gap of the oxide. For all oxides except sapphire, the depth of the ablation crater increases approximately as the square root of the difference between the peak laser fluence and the threshold fluence for ablation. Sapphire shows unique behavior: (i) at laser fluences within 1 J/cm{sup 2} of the threshold for ablation, the depth of the ablation crater increases gradually instead of abruptly with laser fluence, and (ii) the rms roughness of the ablation crater shows a pronounced minimum of <0.2 nm at a laser fluence of 1 J/cm{sup 2} above the threshold.

  17. Near-infrared laser diodes in monitoring applications

    NASA Astrophysics Data System (ADS)

    Patonay, Gabor; Zen, Jyh-Myng; Czuppon, Tibor

    1992-05-01

    Absorption and fluorescence spectroscopy has proven to be a valuable analytical tool for environmental and process monitoring. Several publications have addressed different spectroscopic applications related to process monitoring. Since most chemicals absorb in the UVIVis part of the spectrum, the majority of laser applications utilize this shorter wavelength region. Nevertheless, the utilization of the longer wavelength part of the electromagnetic spectrum may be advantageous due to its relatively low interference. The environmental and process monitoring applications of this spectral region may be especially advantageous if semiconductor lasers are utilized as light sources. Laser diodes have all the properties of other types of lasers with the added benefits of compactness, low power consumption, low cost and long lifetime. However, to utilize this spectral region for environmental or process monitoring applications, appropriate near-infrared (NIR) absorbing probe molecules need to be employed. These probes may be used to determine analytical properties important for environmental or process monitoring applications, e.g., pH, oxygen concentration, metal ion determinations, solvent hydrophobicity, just to mention a few. These NIR probes may be incorporated into polymers to form a stable probe arrangement for convenient monitoring using semiconductor lasers. The utility can be further enhanced using fiber optics. In this paper the use of MR absorption and fluorescence spectroscopy for monitoring applications will be demonstrated.

  18. Retinal safety of near-infrared lasers in cataract surgery

    NASA Astrophysics Data System (ADS)

    Wang, Jenny; Sramek, Christopher; Paulus, Yannis M.; Lavinsky, Daniel; Schuele, Georg; Anderson, Dan; Dewey, David; Palanker, Daniel

    2012-09-01

    Femtosecond lasers have added unprecedented precision and reproducibility to cataract surgery. However, retinal safety limits for the near-infrared lasers employed in surgery are not well quantified. We determined retinal injury thresholds for scanning patterns while considering the effects of reduced blood perfusion from rising intraocular pressure and retinal protection from light scattering on bubbles and tissue fragments produced by laser cutting. We measured retinal damage thresholds of a stationary, 1030-nm, continuous-wave laser with 2.6-mm retinal spot size for 10- and 100-s exposures in rabbits to be 1.35 W (1.26 to 1.42) and 0.78 W (0.73 to 0.83), respectively, and 1.08 W (0.96 to 1.11) and 0.36 W (0.33 to 0.41) when retinal perfusion is blocked. These thresholds were input into a computational model of ocular heating to calculate damage threshold temperatures. By requiring the tissue temperature to remain below the damage threshold temperatures determined in stationary beam experiments, one can calculate conservative damage thresholds for cataract surgery patterns. Light scattering on microbubbles and tissue fragments decreased the transmitted power by 88% within a 12 deg angle, adding a significant margin for retinal safety. These results can be used for assessment of the maximum permissible exposure during laser cataract surgery under various assumptions of blood perfusion, treatment duration, and scanning patterns.

  19. Dy:PbGa2S4 laser radiation and its delivery by hollow waveguide

    NASA Astrophysics Data System (ADS)

    Jelínková, Helena; Nemec, Michal; Miyagi, Mitsunobu; Iwai, Katsumasa; Takaku, Hiroyuki; Doroshenko, Maxim; Basiev, Tasoltan T.; Badikov, Valerii V.; Badikov, Dmitri V.

    2012-01-01

    The mid-infrared radiation generated by bulk Dy:PbGa2S4 laser working at room temperature was characterized and for its delivery the special type of COP/Ag hollow waveguide was used. The optical pumping of Dy:PbGa2S4 laser was performed by flashlamp pumped Er:YLF laser at 1.73 μm wavelength. The compact 60 mm long Dy:PbGa2S4 laser oscillator worked in free-running mode with the repetition rate 1.5 Hz. The output energy was 5.1 mJ in 80 μs long pulse at 4.3 μm wavelength. The spatial beam structure was close to the Gaussian shape. The goal of the presented study was the preliminary investigation of the mid-infrared Dy:PbGa2S4 radiation delivery possibility by the cyclic olefin polymer and silver coated hollow glass waveguide. The length of the waveguide was 103 cm and the inner diameter was 700 μm. The thickness of the polymer inner layer was calculated for the optimal 4 μm radiation transmission. Mid-infrared laser radiation was coupled into the waveguide by the CaF2 lens with the focal length 55 mm. The characterization of delivered 4.3 μm radiation was provided. It was observed that the spatial structure is changing essentially, which follows from the transmission principle of the hollow waveguide. As conclude the delivery system for 4.3 μm mid-infrared Dy:PbGa2S4 laser radiation was investigated for the first time.

  20. Quantum band engineering of nitride semiconductors for infrared lasers

    NASA Astrophysics Data System (ADS)

    Malis, O.; Edmunds, C.; Li, D.; Shao, J.; Gardner, G.; Li, W.; Fay, P.; Manfra, M. J.

    2014-02-01

    The III-nitride semiconductors have been proposed as candidate materials for new quantum cascade lasers in the nearinfrared (1.5-3 μm), and far-infrared (30-60 μm), due to the large conduction-band offset between GaN and Alcontaining alloys (>1 eV), and the large longitudinal optical (LO) phonon energy (90 meV), respectively. The challenges of III-nitride intersubband devices are twofold: material and design related. Due to large electron effective mass, the nitride intersubband materials require the ability to fine-tune the atomic structure at an unprecedented sub-nanometer level. Moreover, the III-N materials exhibit built-in polarization fields that complicate the design of intersubband lasers. This paper presents recent results on c-plane nitride resonant-tunneling diodes that are important for the prospects of farinfrared nitride lasers. We also report near-infrared absorption and photocurrent measurements in nonpolar (m-plane) AlGaN/GaN superlattices.

  1. Microscopic spectral imaging using mid-infrared semiconductor lasers

    NASA Astrophysics Data System (ADS)

    Guo, Bujin-.; Wang, Yi; Peng, Chuan; Luo, Guipeng; Le, Han Q.

    2003-07-01

    Infrared micro-spectroscopy is a useful tool for basic research and biomedical applications. Conventional microspectroscopic imaging apparatuses use thermal sources for sample illumination, which have low brightness, low optical spectral intensity, and high noise. This work evaluates the system engineering advantages of using mid-infrared semiconductor lasers that offer orders-of magnitude higher brightness, spectral intensity, and lower noise. A laser-based microscopic spectral imaging system with focal plane array detectors demonstrated a high signal-to-noise ratio (>20 dB) at video frame rate for a large illuminated area. Microscopic spectral imaging with fixed-wavelength and tunable lasers of 4.6, 6, and 9.3-μm wavelength was applied to a number of representative samples that consist of biological tissues (plant and animal) and solid material (a stack of laminated polymers). Transmission spectral images with ~30-dB dynamic range were obtained with clear evidence of spectral features for different samples. The potential of more advanced systems with a wide coverage of spectral bands is discussed.

  2. Infrared Signature Masking by Air Plasma Radiation

    NASA Technical Reports Server (NTRS)

    Kruger, C. H.; Laux, C. O.

    1998-01-01

    Detailed measurements and modeling of the spectral emission of an atmospheric pressure air plasma at temperatures up to -3400 K have been made. The cold gas injected in the plasma torch contained an estimated mole fraction of water vapor of approximately 4.5 x 10(exp -3) and an estimated carbon dioxide mole fraction of approximately 3.3 x 10(exp -4). Under these conditions, the minimum level of air plasma emission is found to be between 3.9 and 4.15 microns. Outside this narrow region, significant spectral emission is detected that can be attributed to the fundamental and overtone bands of NO and OH, and to the v(sub 3) and the (v(sub 1)+v(sub 3)) bands Of CO2. Special attention was paid to the effects of ambient air absorption in the optical path between the plasma and the detector. Excellent quantitative agreement is obtained between the measured and simulated spectra, which are both on absolute intensity scales, thus lending confidence in the radiation models incorporated into NEQAIR2-IR over the course of this research program.

  3. Effects of Near-Infrared Laser on Neural Cell Activity

    NASA Astrophysics Data System (ADS)

    Mochizuki-Oda, Noriko; Kataoka, Yosky; Yamada, Hisao; Awazu, Kunio

    2004-08-01

    Near-infrared laser has been used to relieve patients from various kinds of pain caused by postherpetic neuralgesia, myofascial dysfunction, surgical and traumatic wound, cancer, and rheumatoid arthritis. Clinically, He-Ne (λ=632.8 nm, 780 nm) and Ga-Al-As (805 ± 25 nm) lasers are used to irradiate trigger points or nerve ganglion. However the precise mechanisms of such biological actions of the laser have not yet been resolved. Since laser therapy is often effective to suppress the pain caused by hyperactive excitation of sensory neurons, interactions with laser light and neural cells are suggested. As neural excitation requires large amount of energy liberated from adenosine triphosphate (ATP), we examined the effect of 830-nm laser irradiation on the energy metabolism of the rat central nervous system and isolated mitochondria from brain. The diode laser was applied for 15 min with irradiance of 4.8 W/cm2 on a 2 mm-diameter spot at the brain surface. Tissue ATP content of the irradiated area in the cerebral cortex was 19 % higher than that of the non-treated area (opposite side of the cortex), whereas the ADP content showed no significant difference. Irradiation at another wavelength (652 nm) had no effect on either ATP or ADP contents. The temperature of the brain tissue was increased 4.5 - 5.0 °C during the irradiation of both 830-nm and 652-nm laser light. Direct irradiation of the mitochondrial suspension did not show any wavelength-dependent acceleration of respiration rate nor ATP synthesis. These results suggest that the increase in tissue ATP content did not result from the thermal effect, but from specific effect of the laser operated at 830 nm. Electrophysiological studies showed the hyperpolarization of membrane potential of isolated neurons and decrease in membrane resistance with irradiation of the laser, suggesting an activation of potassium channels. Intracellular ATP is reported to regulate some kinds of potassium channels. Possible mechanisms

  4. Infrared laser sealing of porcine tissues: preliminary in vivo studies

    NASA Astrophysics Data System (ADS)

    Cilip, Christopher M.; Hutchens, Thomas C.; Kerr, Duane; Latimer, Cassandra; Rosenbury, Sarah B.; Giglio, Nicholas C.; Schweinsberger, Gino R.; Perkins, William C.; Wilson, Christopher R.; Ward, Arlen; Nau, William H.; Fried, Nathaniel M.

    2015-02-01

    We are exploring infrared (IR) lasers as an alternative energy modality to radiofrequency (RF) and ultrasonic (US) devices intended to provide rapid surgical hemostasis with minimal collateral zones of thermal damage and tissue necrosis. Previously, a 1470-nm IR laser sealed and cut ex vivo porcine renal arteries of 1-8 mm in 2 s, yielding burst pressures < 1200 mmHg (compared to normal systolic blood pressure of 120 mmHg) and thermal coagulation zones < 3 mm (including the seal). This preliminary study describes in vivo testing of a laser probe in a porcine model. A prototype, fiber optic based handheld probe with vessel/tissue clasping mechanism was tested on blood vessels < 6 mm diameter using incident 1470-nm laser power of 35 W for 1-5 s. The probe was evaluated for hemostasis after sealing isolated and bundled vasculature of abdomen and hind leg, as well as liver and lung parenchyma. Sealed vessel samples were collected for histological analysis of lateral thermal damage. Hemostasis was achieved in 57 of 73 seals (78%). The probe consistently sealed vasculature in small bowel mesentery, mesometrium, and gastro splenic and epiploic regions. Seal performance was less consistent on hind leg vasculature including saphenous arteries and bundles and femoral and iliac arteries. Collagen denaturation averaged 1.6 mm in 8 samples excised for histologic examination. A handheld laser probe sealed porcine vessels in vivo. With further improvements in probe design and laser parameter optimization, IR lasers may provide an alternative to RF and US vessel sealing devices.

  5. Flexible hollow polycarbonate fiber for endoscopic infrared laser treatment

    NASA Astrophysics Data System (ADS)

    Nakazawa, Masayuki; Shi, Yi-Wei; Iwai, Katsumasa; Matsuura, Yuji; Zhu, Xiao-Song; Miyagi, Mitsunobu

    2007-07-01

    For endoscopic application, inexpensive, safe, and extremely flexible hollow infrared optical fibers have been fabricated based on the polycarbonate (PC) capillary with silver and cyclic olefin polymer (COP) as inner coatings. By optimizing the drawing condition of PC capillary from a commercially available polycarbonate tube and inner-coating process, transmission efficiency of hollow PC fibers is shown to be equal to those of glass capillary based ones. Both Er:YAG laser light and green pilot beam were delivered through the endoscope with low losses even when it was sharply bent with a bending radius as small as 1 centimeter. Preliminary experiments were also conducted on possibility of transmitting infrared thermal image by using bundled silver-coated PC hollow fibers.

  6. Broadband infrared vibrational nano-spectroscopy using thermal blackbody radiation.

    PubMed

    O'Callahan, Brian T; Lewis, William E; Möbius, Silke; Stanley, Jared C; Muller, Eric A; Raschke, Markus B

    2015-12-14

    Infrared vibrational nano-spectroscopy based on scattering scanning near-field optical microscopy (s-SNOM) provides intrinsic chemical specificity with nanometer spatial resolution. Here we use incoherent infrared radiation from a 1400 K thermal blackbody emitter for broadband infrared (IR) nano-spectroscopy. With optimized interferometric heterodyne signal amplification we achieve few-monolayer sensitivity in phonon polariton spectroscopy and attomolar molecular vibrational spectroscopy. Near-field localization and nanoscale spatial resolution is demonstrated in imaging flakes of hexagonal boron nitride (hBN) and determination of its phonon polariton dispersion relation. The signal-to-noise ratio calculations and analysis for different samples and illumination sources provide a reference for irradiance requirements and the attainable near-field signal levels in s-SNOM in general. The use of a thermal emitter as an IR source thus opens s-SNOM for routine chemical FTIR nano-spectroscopy. PMID:26698997

  7. High field CdS detector for infrared radiation

    NASA Technical Reports Server (NTRS)

    Tyagi, R. C.; Robertson, J. B.; Boer, K. W.; Hadley, H. C., Jr. (Inventor)

    1974-01-01

    An infrared radiation detector including a cadmium sulfide platelet having a cathode formed on one of its ends and an anode formed on its other end is presented. The platelet is suitably doped such that stationary high-field domains are formed adjacent the cathode when based in the negative differential conductivity region. A negative potential is applied to the cathode such that a high-field domain is formed adjacent to the cathode. A potential measuring probe is located between the cathode and the anode at the edge of the high-field domain and means are provided for measuring the potential at the probe whereby this measurement is indicative of the infrared radiation striking the platelet.

  8. Infrared laser-induced breakdown spectroscopy emissions from energetic materials

    NASA Astrophysics Data System (ADS)

    Yang, Clayton S.; Brown, E.; Hommerich, Uwe; Trivedi, Sudhir B.; Samuels, Alan C.; Snyder, A. Peter

    2011-05-01

    Laser-induced breakdown spectroscopy (LIBS) has shown great promise for applications in chemical, biological, and explosives (CBE) sensing and has significant potential for real time standoff detection and analysis. We have studied LIBS emissions in the mid-infrared (MIR) spectral region for potential applications in CBE sensing. Detailed MIR-LIBS studies were performed for several energetic materials for the first time. In this study, the IR signature spectral region between 4 - 12 um was mined for the appearance of MIR-LIBS emissions that are directly indicative of oxygenated breakdown products as well as partially dissociated and recombination molecular species.

  9. Tunable Infrared Laser Instruments for Airborne Atmospheric Studies

    NASA Technical Reports Server (NTRS)

    Fried, A.; Diskin, G.; Weibring, P.; Richter, D.; Walega, J. G.; Sachse, G.; Slate, T.; Rana, M.; Podolske, J.

    2008-01-01

    Tunable infrared laser-based instruments on airborne platforms have provided invaluable contributions to atmospheric studies over the past several decades. This paper presents an overview of some recent studies and developments using this approach that were presented at the 2007 Field Laser Applications in Industry and Research (FLAIR, http://www.inoa.it/flair/) conference in Florence, Italy. The present overview only covers select in situ absorption-based instruments that were presented in the airborne session at this conference. In no case are comprehensive details presented. These details can be found in the numerous references given. Additional approaches based upon cavity-enhanced and photoacoustic measurements, which are also making invaluable contributions in airborne atmospheric studies, are not discussed in this brief overview.

  10. Scattering assisted injection based injectorless mid infrared quantum cascade laser

    SciTech Connect

    Singh, Siddharth Kamoua, Ridha

    2014-06-07

    An injectorless five-well mid infrared quantum cascade laser is analyzed which relies on phonon scattering injection in contrast to resonant tunneling injection, which has been previously used for injectorless designs. A Monte Carlo based self-consistent electron and photon transport simulator is used to analyze the performance of the analyzed design and compare it to existing injectorless designs. The simulation results show that the analyzed design could greatly enhance the optical gain and the characteristic temperatures of injectorless quantum cascade lasers (QCLs) which have typically been hindered by low characteristic temperatures and significant temperature related performance degradation. Simulations of the analyzed device predict threshold current densities of 0.85 kA/cm{sup 2} and 1.95 kA/cm{sup 2} at 77 K and 300 K, respectively, which are comparable to the threshold current densities of conventional injector based QCLs.

  11. Chemical analysis of surgical smoke by infrared laser spectroscopy

    NASA Astrophysics Data System (ADS)

    Gianella, Michele; Sigrist, Markus W.

    2012-11-01

    The chemical composition of surgical smoke, a gaseous by-product of some surgical devices—lasers, drills, vessel sealing devices—is of great interest due to the many toxic components that have been found to date. For the first time, surgical smoke samples collected during routine keyhole surgery were analyzed with infrared laser spectroscopy. Traces (ppm range) of methane, ethane, ethylene, carbon monoxide and sevoflurane were detected in the samples which consisted mostly of carbon dioxide and water vapor. Except for the anaesthetic sevoflurane, none of the compounds were present at dangerous concentrations. Negative effects on the health of operation room personnel can be excluded for many toxic compounds found in earlier studies, since their concentrations are below recommended exposure limits.

  12. Infrared laser welding of the rabbit cornea in vivo

    NASA Astrophysics Data System (ADS)

    Williams, John M.; Burstein, Neal L.; Nowicki, Michael J.; Zietkiewicz, Christopher J.; Jeffers, William Q.

    1995-05-01

    The hydrogen fluoride laser has been used to successfully weld corneal tissue in vivo. Previous experiments have demonstrate the success of producing watertight welds in both porcine and human cadaver corneas. Wound bursting strengths of up to three times normal intraocular pressure have been reported. In this study, an in vivo model was utilized, specifically the rabbit cornea. Twelve New Zealand white rabbits, received a 7 mm, full thickness, linear corneal incision in one eye, and stay sutures were placed. Six of the wounds were welded with a semiconductor infrared laser, and six eyes served as controls. At two and four weeks, both histologic and tensiometric studies were performed. There was a trend toward increasing wound strength when the two and four week specimens were compared. Corneal welding may prove to be an adjunct to current suturing techniques in humans. Procedures requiring the closure of corneal incisions such as cataract extraction or penetrating keratoplasty may benefit from this technique.

  13. Suggested state regulations for control fo radiation. Volume 2: Nonionizing radiation, lasers

    NASA Astrophysics Data System (ADS)

    Information is presented on classifying lasers into four classes is presented; defines what a laser product is; states requirements for medical surveillance for persons exposed to laser radiation; specifies requirements for registration of laser facilities, mobile lasers, and persons servicing lasers/systems.

  14. Investigation of infra-red and nonequilibrium air radiation

    NASA Technical Reports Server (NTRS)

    Kruger, Charles H.

    1995-01-01

    This report describes progress on the first year of a research program on the infrared radiation of air plasmas conducted in the High Temperature Gasdynamics Laboratory at Stanford University. This program is intended to investigate the masking of infrared signatures by the air plasma formed behind the bow shock of high velocity missiles. To this date, the radiative emission of air plasmas in the infrared has been the object of few experimental investigations, and although several infrared systems are already modeled in radiation codes such as NEQAIR, measurements are required to validate numerical predictions and indicate whether all transitions of importance are accounted for. The present program is motivated by the fact that 9 excited states (A, B, C, D, B', F, H, and H') of NO radiate in the infrared, especially between 1 and 1.5 microns where at least 9 transitions involving can be observed. Because these IR transitions are relatively well separated from each other, excited NO states concentrations can be easily measured, thus providing essential information on excited-state chemistry for use in optical diagnostics or in electronic excitation model validation. Developing accurate collisional-radiative models for these excited NO states is of importance as the UV-VUV transitions of NO (beta, gamma, epsilon, beta prime, gamma prime) produce a major, if not dominant, fraction of the radiation emitted by air plasmas. During the first year of the program, research has focused on the spectral range 1.0 to 1.5 microns, as detailed in Section 2 of this report. The measurements, conducted in a 50 kW radio-frequency inductively coupled plasma torch operating on air at atmospheric pressure, extend previous shock tube investigations by Wray to a wider spectral range (1.0 to 1.5 microns vs 0.9 to 1.2 microns) and higher temperatures (7600 K in the plasma torch versus 6700 K in the shock-tube). These higher temperatures in the present experiment have made it possible to

  15. Effect of helium-neon and infrared laser irradiation on wound healing in rabbits

    SciTech Connect

    Braverman, B.; McCarthy, R.J.; Ivankovich, A.D.; Forde, D.E.; Overfield, M.; Bapna, M.S.

    1989-01-01

    We examined the biostimulating effects of helium-neon laser radiation (HeNe; 632.8 nm), pulsed infrared laser radiation (IR; 904 nm), and the two combined on skin wound healing in New Zealand white rabbits. Seventy-two rabbits received either (1) no exposure, (2) 1.65 J/cm2 HeNe, (3) 8.25 J/cm2 pulsed IR, or (4) both HeNe and IR together to one of two dorsal full-thickness skin wounds, daily, for 21 days. Wound areas were measured photographically at periodic intervals. Tissue samples were analyzed for tensile strength, and histology was done to measure epidermal thickness and cross-sectional collagen area. Significant differences were found in the tensile strength of all laser-treated groups (both the irradiated and nonirradiated lesion) compared to group 1. No differences were found in the rate of wound healing or collagen area. Epidermal growth was greater in the HeNe-lased area compared to unexposed tissue, but the difference was not significant. Thus, laser irradiation at 632.8 nm and 904 nm alone or in combination increased tensile strength during wound healing and may have released tissue factors into the systemic circulation that increased tensile strength on the opposite side as well.

  16. Infrared Laser Ablation Sample Transfer for MALDI and Electrospray

    NASA Astrophysics Data System (ADS)

    Park, Sung-Gun; Murray, Kermit King

    2011-08-01

    We have used an infrared laser to ablate materials under ambient conditions that were captured in solvent droplets. The droplets were either deposited on a MALDI target for off-line analysis by MALDI time-of-flight mass spectrometry or flow-injected into a nanoelectrospray source of an ion trap mass spectrometer. An infrared optical parametric oscillator (OPO) laser system at 2.94 μm wavelength and approximately 1 mJ pulse energy was focused onto samples for ablation at atmospheric pressure. The ablated material was captured in a solvent droplet 1-2 mm in diameter that was suspended from a silica capillary a few millimeters above the sample target. Once the sample was transferred to the droplet by ablation, the droplet was deposited on a MALDI target. A saturated matrix solution was added to the deposited sample, or in some cases, the suspended capture droplet contained the matrix. Peptide and protein standards were used to assess the effects of the number of IR laser ablation shots, sample to droplet distance, capture droplet size, droplet solvent, and laser pulse energy. Droplet collected samples were also injected into a nanoelectrospray source of an ion trap mass spectrometer with a 500 nL injection loop. It is estimated that pmol quantities of material were transferred to the droplet with an efficiency of approximately 1%. The direct analysis of biological fluids for off-line MALDI and electrospray was demonstrated with blood, milk, and egg. The implications of this IR ablation sample transfer approach for ambient imaging are discussed.

  17. Infrared Laser Activation of Soluble and Membrane Protein Assemblies in the Gas Phase.

    PubMed

    Mikhailov, Victor A; Liko, Idlir; Mize, Todd H; Bush, Matthew F; Benesch, Justin L P; Robinson, Carol V

    2016-07-19

    Collision-induced dissociation (CID) is the dominant method for probing intact macromolecular complexes in the gas phase by means of mass spectrometry (MS). The energy obtained from collisional activation is dependent on the charge state of the ion and the pressures and potentials within the instrument: these factors limit CID capability. Activation by infrared (IR) laser radiation offers an attractive alternative as the radiation energy absorbed by the ions is charge-state-independent and the intensity and time scale of activation is controlled by a laser source external to the mass spectrometer. Here we implement and apply IR activation, in different irradiation regimes, to study both soluble and membrane protein assemblies. We show that IR activation using high-intensity pulsed lasers is faster than collisional and radiative cooling and requires much lower energy than continuous IR irradiation. We demonstrate that IR activation is an effective means for studying membrane protein assemblies, and liberate an intact V-type ATPase complex from detergent micelles, a result that cannot be achieved by means of CID using standard collision energies. Notably, we find that IR activation can be sufficiently soft to retain specific lipids bound to the complex. We further demonstrate that, by applying a combination of collisional activation, mass selection, and IR activation of the liberated complex, we can elucidate subunit stoichiometry and the masses of specifically bound lipids in a single MS experiment. PMID:27328020

  18. Laser hyperdoping silicon for enhanced infrared optoelectronic properties

    NASA Astrophysics Data System (ADS)

    Warrender, Jeffrey M.

    2016-09-01

    Pulsed laser melting and rapid solidification have attracted interest for decades as a method to achieve impurity concentrations in silicon orders of magnitude above the equilibrium solubility limit. The incorporation of sulfur into silicon using this technique led to the observation of strong broadband infrared absorption in the resulting material. This observation, combined with interest in impurity band optoelectronic device concepts, has resulted in renewed interest in laser techniques for achieving high impurity concentrations. In this paper, I review the literature that led to the present understanding of laser hyperdoping and provide a summary of the optical and optoelectronic measurements made on sulfur hyperdoped silicon to date. I mention recent work exploring transition metal impurities and discuss how considerations discovered in early solidification and later rapid solidification work inform our approaches to kinetically trapping such impurities. I also provide a simplified picture of how a laser hyperdoping process is typically carried out, as an entry point for an experimentalist seeking to fabricate such layers.

  19. Diode laser arrays for dynamic infrared scene projection

    NASA Astrophysics Data System (ADS)

    Beasley, D. Brett; Cooper, John B.

    1993-08-01

    A novel concept for dynamic IR scene projection using IR diode lasers has been developed. This technology offers significant cost and performance advantages over other currently available projector technologies. Performance advantages include high dynamic range, multiple wavebands, and high frame rates. A projector system which utilizes a 16-element linear array has been developed and integrated into the millimeter wave/infrared (MMW/IR) hardware-in-the-loop (HWIL) facility at the US Army Missile Command's (USAMICOM's) Research, Development, and Engineering Center (RDEC). This projector has demonstrated dynamic range in excess of 105, apparent temperatures greater than 2500 degree(s)C, and nanosecond response times. Performance characteristics for this projector system are presented in the paper. Designs for projectors to test other IR sensor configurations, including FPAs, have been developed and are presented as well. The FPA design consists of a linear array of diode lasers scanned by a polygon mirror. This low-cost projector offers high resolution, high contrast 2-D scenes at up to 10 KHz frame rates. Simulation of active IR countermeasures is another promising application of diode laser projector systems. The diode laser is capable of simulating flares or virtually any IR jammer waveform.

  20. Investigation of germanium Raman lasers for the mid-infrared.

    PubMed

    De Leonardis, Francesco; Troia, Benedetto; Soref, Richard A; Passaro, Vittorio M N

    2015-06-29

    In this paper we present a detailed theoretical investigation of integrated racetrack Raman lasers based on the germanium material system operating in the mid-infrared beyond the germanium two-photon absorption cut-off wavelength of 3.17 μm. The effective Raman gain has been estimated in waveguides based on germanium-on-silicon, germanium-on-SOI and germanium-on-Si3N4 technology platforms as a function of their crystallographic orientations. Furthermore, general design guidelines have been determined by means of a comparative analysis of Raman laser performance, i.e. the threshold power, polarization and directionality of the excited Stokes signals as a function of racetrack cavity length and directional-coupler dimensions. Finally, the emitted Raman laser power has been evaluated as a function of overall propagation losses and operative wavelengths up to 3.8 μm, while the time dynamics of Raman lasers has been simulated assuming continuous and pulse waves as input pump signals. PMID:26191733

  1. High-power continuous-wave mid-infrared radiation generated by difference frequency mixing of diode-laser-seeded fiber amplifiers and its application to dual-beam spectroscopy

    NASA Technical Reports Server (NTRS)

    Lancaster, D. G.; Richter, D.; Curl, R. F.; Tittel, F. K.; Goldberg, L.; Koplow, J.

    1999-01-01

    We report the generation of up to 0.7 mW of narrow-linewidth (<60-MHz) radiation at 3.3 micrometers by difference frequency mixing of a Nd:YAG-seeded 1.6-W Yb fiber amplifier and a 1.5-micrometers diode-laser-seeded 0.6-W Er/Yb fiber amplifier in periodically poled LiNbO3. A conversion efficiency of 0.09%/W (0.47 mWW-2 cm-1) was achieved. A room-air CH4 spectrum acquired with a compact 80-m multipass cell and a dual-beam spectroscopic configuration indicates an absorption sensitivity of +/-2.8 x 10(-5) (+/-1 sigma), corresponding to a sub-parts-in-10(9) (ppb) CH4 sensitivity (0.8 ppb).

  2. Quantitative dental measurements by use of simultaneous frequency-domain laser infrared photothermal radiometry and luminescence.

    PubMed

    Nicolaides, Lena; Feng, Chris; Mandelis, Andreas; Abrams, Stephen H

    2002-02-01

    Modulated (frequency-domain) infrared photothermal radiometry (PTR) is used as a dynamic quantitative dental inspection tool complementary to modulated luminescence (LM) to quantify sound enamel or dentin. A dynamic high-spatial-resolution experimental imaging setup, which can provide simultaneous measurements of laser-induced modulated PTR and LM signals from defects in teeth, has been developed. Following optical absorption of laser photons, the experimental setup can monitor simultaneously and independently the nonradiative (optical-to-thermal) energy conversion by infrared PTR and the radiative deexcitation by LM emission. The relaxation lifetimes (tau1, tau2) and optical absorption, scattering, and spectrally averaged infrared emission coefficients (mu(alpha), mu(s), mu(IR)) of enamel are then determined with realistic three-dimensional LM and photothermal models for turbid media followed by multiparameter fits to the data. A quantitative band of values for healthy enamel with respect to these parameters can be generated so as to provide an explicit criterion for the assessment of healthy enamel and, in a future extension, to facilitate the diagnosis of the onset of demineralization in carious enamel. PMID:11993925

  3. Radiative trapping in intense laser beams

    NASA Astrophysics Data System (ADS)

    Kirk, J. G.

    2016-08-01

    The dynamics of electrons in counter-propagating, circularly polarized laser beams are shown to exhibit attractors whose ability to trap particles depends on the ratio of the beam intensities and a single parameter describing radiation reaction. Analytical expressions are found for the underlying limit cycles and the parameter range in which they are stable. In high-intensity optical pulses, where radiation reaction strongly modifies the trajectories, the production of collimated gamma-rays and the initiation of non-linear cascades of electron–positron pairs can be optimized by a suitable choice of the intensity ratio.

  4. Features of gallstone and kidney stone fragmentation by IR-pulsed Nd:YAG laser radiation

    NASA Astrophysics Data System (ADS)

    Batishche, Sergei A.

    1995-05-01

    It is shown that infra-red ((lambda) equals 1064 nm) long pulse (approximately 100 microsecond(s) ) radiation of YAG:Nd laser, operating in free generation regime, effectively fragments gallstones, urinary calculus and kidney stones. The features of the mechanism of this process are investigated. Laser lithotripsy is nowadays a method widely used for fragmentation of gallstones, urinary calculus and kidney stones. Flashlamp pumped dye lasers of microsecond duration are most often used for such purposes. Nevertheless, there are some reports on lithotripsies with nanosecond duration laser pulses (for example, Q-switched YAG:Nd laser). The mechanism of the laser fragmentation of such stones was supposed to be the next. The laser powerful radiation, delivered through the optical fiber, is absorbed by the material of the stone. As a result of such highly localized energy absorption, dense plasma is formed, which expands. Such plasma and vapor, liquid confined, forms a cavitation bubble. This bubble grows, reaches its most dimension and then collapses on itself in some hundreds of micro seconds. Shock waves generated during the growth and the collapse of these bubbles are the origin of fragmentation of the stone. It is necessary to say that there are rather confined data on the hundreds microsecond laser pulse fragmentation especially what concerns the usage of infra-red (IR) YAG:Nd lasers with long laser pulses. Clearing this problem would result in better understanding of the fragmentation mechanism and it could favor development of simple and more reliable laser systems for lithotripsy. In this work we report about investigation of features of an effective fragmentation of gallstones, urinary calculus and kidney stones under exposure of IR ((lambda) equals 1064 nm) radiation of repetitive YAG:Nd laser working in free generation regime.

  5. Mid-infrared absorption spectroscopy using quantum cascade lasers

    NASA Astrophysics Data System (ADS)

    Haibach, Fred; Erlich, Adam; Deutsch, Erik

    2011-06-01

    Block Engineering has developed an absorption spectroscopy system based on widely tunable Quantum Cascade Lasers (QCL). The QCL spectrometer rapidly cycles through a user-selected range in the mid-infrared spectrum, between 6 to 12 μm (1667 to 833 cm-1), to detect and identify substances on surfaces based on their absorption characteristics from a standoff distance of up to 2 feet with an eye-safe laser. It can also analyze vapors and liquids in a single device. For military applications, the QCL spectrometer has demonstrated trace explosive, chemical warfare agent (CWA), and toxic industrial chemical (TIC) detection and analysis. The QCL's higher power density enables measurements from diffuse and highly absorbing materials and substrates. Other advantages over Fourier Transform Infrared (FTIR) spectroscopy include portability, ruggedness, rapid analysis, and the ability to function from a distance through free space or a fiber optic probe. This paper will discuss the basic technology behind the system and the empirical data on various safety and security applications.

  6. 3-D ice shape measurements using mid-infrared laser scanning.

    PubMed

    Gong, Xiaoliang; Bansmer, Stephan

    2015-02-23

    A general approach based on mid-infrared (MIR) laser scanning is proposed to measure the 3-D ice shape no matter whether the ice is composed of clear ice, rime ice, mixed ice, or even supercooled water droplets or films. This is possible because MIR radiation penetrates ice and water only within a depth of less than 10 micrometers. First, an MIR laser point scanning technique is implemented and verified on transparent glass and clear ice. Then, to improve efficiency, an MIR laser line scanning method is developed and validated on different models. At last, several sequential MIR laser line scans are applied to trace the 3-D shape evolution of the continuous ice accretion on an airfoil in an icing wind tunnel. The ice growth process can be well observed in the results. The MIR scan shows a good agreement with the traditional visible laser scan on a plastic replication of the final ice shape made by the mold and casting method. PMID:25836526

  7. Laser Infrared Desorption Spectroscopy to Detect Complex Organic Molecules on Icy Planetary Surfaces

    NASA Technical Reports Server (NTRS)

    Sollit, Luke S.; Beegle, Luther W.

    2008-01-01

    Laser Desorption-Infrared Spectroscopy (LD-IR) uses an IR laser pulse to desorb surface materials while a spectrometer measures the emission spectrum of the desorbed materials (Figure 1). In this example, laser desorption operates by having the incident laser energy absorbed by near surface material (10 microns in depth). This desorption produces a plume that exists in an excited state at elevated temperatures. A natural analog for this phenomenon can be observed when comets approach the sun and become active and individual molecular emission spectra can be observed in the IR [1,2,3,4,5]. When this occurs in comets, the same species that initially emit radiation down to the ground state are free to absorb it, reducing the amount of detectable emission features. The nature of our technique results in absorption not occurring, because the laser pulse could easily be moved away form the initial desorption plume, and still have better spatial resolution then reflectance spectroscopy. In reflectance spectroscopy, trace components have a relatively weak signal when compared to the entire active nature of the surface. With LDIR, the emission spectrum is used to identify and analyze surface materials.

  8. A cesium plasma TELEC device for conversion of laser radiation to electric power

    NASA Technical Reports Server (NTRS)

    Britt, E. J.; Rasor, N. S.; Lee, G.; Billman, K. W.

    1978-01-01

    Tests of the thermoelectronic laser energy converter (TELEC) concept are reported. This device has been devised as a means to convert high-average-power laser radiation into electrical energy, a crucial element in any space laser power transmission scheme using the available high-power/efficiency infrared lasers. Theoretical calculations, based upon inverse bremsstrahlung absorption in a cesium plasma, indicate internal conversion efficiency up to 50% with an overall system efficiency of 42%. The experiments reported were made with a test cell designed to confirm the theoretical model rather than demonstrate efficiency; 10.6-micron laser-beam absorption was limited to about 0.001 of the incident beam by the short absorption region. Nevertheless, confirmatory results were obtained, and the conversion of absorbed radiation to electric power is estimated to be near 10%.

  9. Effects of ionizing radiation on cryogenic infrared detectors

    NASA Technical Reports Server (NTRS)

    Moseley, S. H.; Silverberg, R. F.; Lakew, B.

    1989-01-01

    The Diffuse Infrared Background Experiment (DIRBE) is one of three experiments to be carried aboard the Cosmic Background Explorer (COBE) satellite scheduled to be launched by NASA on a Delta rocket in 1989. The DIRBE is a cryogenic absolute photometer operating in a liquid helium dewar at 1.5 K. Photometric stability is a principal requirement for achieving the scientific objectives of this experiment. The Infrared Astronomy Satellite (IRAS), launched in 1983, which used detectors similar to those in DIRBE, revealed substantial changes in detector responsivity following exposure to ionizing radiation encountered on passage through the South Atlantic Anomaly (SAA). Since the COBE will use the same 900 Km sun-synchronous orbit as IRAS, ionizing radiation-induced performance changes in the detectors were a major concern. Here, ionizing radiation tests carried out on all the DIRBE photodetectors are reported. Responsivity changes following exposure to gamma rays, protons, and alpha particle are discussed. The detector performance was monitored following a simulated entire mission life dose. In addition, the response of the detectors to individual particle interactions was measured. The InSb photovoltaic detectors and the Blocked Impurity Band (BIB) detectors revealed no significant change in responsivity following radiation exposure. The Ge:Ga detectors show large effects which were greatly reduced by proper thermal annealing.

  10. Effects of ionizing radiation on cryogenic infrared detectors

    NASA Astrophysics Data System (ADS)

    Moseley, S. H.; Silverberg, R. F.; Lakew, B.

    The Diffuse Infrared Background Experiment (DIRBE) is one of three experiments to be carried aboard the Cosmic Background Explorer (COBE) satellite scheduled to be launched by NASA on a Delta rocket in 1989. The DIRBE is a cryogenic absolute photometer operating in a liquid helium dewar at 1.5 K. Photometric stability is a principal requirement for achieving the scientific objectives of this experiment. The Infrared Astronomy Satellite (IRAS), launched in 1983, which used detectors similar to those in DIRBE, revealed substantial changes in detector responsivity following exposure to ionizing radiation encountered on passage through the South Atlantic Anomaly (SAA). Since the COBE will use the same 900 Km sun-synchronous orbit as IRAS, ionizing radiation-induced performance changes in the detectors were a major concern. Here, ionizing radiation tests carried out on all the DIRBE photodetectors are reported. Responsivity changes following exposure to gamma rays, protons, and alpha particle are discussed. The detector performance was monitored following a simulated entire mission life dose. In addition, the response of the detectors to individual particle interactions was measured. The InSb photovoltaic detectors and the Blocked Impurity Band (BIB) detectors revealed no significant change in responsivity following radiation exposure. The Ge:Ga detectors show large effects which were greatly reduced by proper thermal annealing.

  11. Effects Of Ionizing Radiation On Cryogenic Infrared Detectors

    NASA Astrophysics Data System (ADS)

    Moseley, S. H.; Lakew, B.; Silverberg, R. F.

    1988-04-01

    The Diffuse Infrared Background Experiment (DIRBE) is one of three experiments to be carried aboard the Cosmic Background Explorer (COBE) satellite scheduled to be launched by NASA on a Delta rocket in 1989. The DIRBE is a cryogenic absolute photometer operating in a liquid helium dewar at 1.5K. Photometric stability is a principal requirement for achieving the scientific objectives of this experiment. The Infrared Astronomy Satellite (IRAS), launched in 1983, which used detectors similar to those in DIRBE, revealed substantial changes in detector responsivity following exposure to ionizing radiation encountered on passage through the South Atlantic Anomaly (SAA). Since the COBE will use the same 900 Km sun-synchronous orbit as IRAS, ionizing radiation-induced performance changes in the detectors were a major concern. We report here on ionizing radiation tests carried out on all the DIRBE photodetectors. Responsivity changes following exposure to gamma rays, protons, and alpha particle are discussed. The detector performance was monitored following a simulated entire mission life dose. In addition, the response of the detectors to individual particle interactions was measured. The InSb photovoltaic detectors and the Blocked Impurity Band (BIB) detectors revealed no significant change in responsivity following radiation exposure. The Ge:Ga detectors show large effects which were greatly reduced by proper thermal annealing.

  12. Changes in mouse Leydig cell steroidogenesis following infrared and helium-neon laser irradiation.

    PubMed

    Celani, M F; Grandi, M; Gilioli, G

    1987-03-01

    The effects on mouse Leydig cell steroidogenesis of infrared (IR) laser rays, in the presence or absence of helium-neon (He-Ne) radiations, were investigated. Testosterone (T) production in response to luteinizing hormone (LH) by mouse Leydig cells exposed to IR (4.2 X 10(-3) J/cm2/min) plus He-Ne (8.0 X 10(-7) J/cm2/min) laser radiations was significantly higher than that by control Leydig cells. The Leydig cell responsiveness to LH (T delta %), as well as the secretion of cyclic AMP (cAMP) and androstenedione (A) in response to the highest dose of LH (0.5 mIU), were also significantly increased by the IR plus He-Ne irradiation. In contrast, the He-Ne irradiation (8.0 X 10(-7) J/cm2/min) in the absence of IR rays failed to affect T production by mouse Leydig cells. Similar results were obtained by adding to the He-Ne rays a low dose of IR radiation (3.4 X 10(-3) J/cm2/min), whereas higher doses of IR radiations (4.2 X 10(-3) and 5.1 X 10(-3) J/cm2/min) elicited a similar significant increase of T production by mouse interstitial cells. PMID:3595730

  13. Combination of fiber-guided pulsed erbium and holmium laser radiation for tissue ablation under water

    NASA Astrophysics Data System (ADS)

    Pratisto, Hans; Frenz, Martin; Ith, Michael; Altermatt, Hans J.; Jansen, E. Duco; Weber, Heinz P.

    1996-07-01

    Because of the high absorption of near-infrared laser radiation in biological tissue, erbium lasers and holmium lasers emitting at 3 and 2 mu m, respectively, have been proven to have optimal qualities for cutting or welding and coagulating tissue. To combine the advantages of both wavelengths, we realized a multiwavelength laser system by simultaneously guiding erbium and holmium laser radiation by means of a single zirconium fluoride (ZrF4) fiber. Laser-induced channel formation in water and poly(acrylamide) gel was investigated by the use of a time-resolved flash-photography setup, while pressure transients were recorded simultaneously with a needle hydrophone. The shapes and depths of vapor channels produced in water and in a submerged gel after single erbium and after combination erbium-holmium radiation delivered by means of a 400- mu m ZrF4 fiber were measured. Transmission measurements were performed to determine the amount of pulse energy available for tissue ablation. The effects of laser wavelength and the delay time between pulses of different wavelengths on the photomechanical and photothermal responses of meniscal tissue were evaluated in vitro by the use of histology. It was observed that the use of a short (200- mu s, 100-mJ) holmium laser pulse as a prepulse to generate a vapor bubble through which the ablating erbium laser pulse can be transmitted (delay time, 100 mu s) increases the cutting depth in meniscus from 450 to 1120 mu m as compared with the depth following a single erbium pulse. The results indicate that a combination of erbium and holmium laser radiation precisely and efficiently cuts tissue under water with 20-50- mu m collateral tissue damage. wave, cavitation, channel formation, infrared-fiber-delivery system, tissue damage, cartilage.

  14. Temperature stability improvement of a QVGA uncooled infrared radiation FPA

    NASA Astrophysics Data System (ADS)

    Ishii, Koichi; Honda, Hiroto; Fujiwara, Ikuo; Sasaki, Keita; Yagi, Hitoshi; Suzuki, Kazuhiro; Kwon, Honam; Atsuta, Masaki; Funaki, Hideyuki

    2013-06-01

    We have developed a low-cost uncooled infrared radiation focal plane array (FPA) requiring no thermoelectric cooler (TEC), which has 320 x 240 detection pixels with 22 um pitch. The silicon single-crystal series p-n junction diodes and the low-noise readout circuit on the same SOI wafer fabricated by 0.13 um CMOS technology were utilized for infrared (IR) detection. The temperature dependence in the readout circuit was eliminated by correlated double sampling (CDS) operation with reference pixel that was insensitive to infrared radiation. In order to reduce the temperature dependence, we improved the reference pixel and the readout circuit. Although the reference pixels should be completely insensitive to IR radiation, prior reference pixels showed measurable sensitivity. The improved reference pixel was formed by partially releasing with bulk-micromachining and was verified to be insensitive to IR radiation by an object of 400°C. The readout circuit had a differential amplifier instead of a singletransistor amplifier and an analog-to-digital converter (ADC). In each portion, CDS was applied to reduce temperature dependence. The first CDS operation was used for eliminating the pixel output variation and the second operation was used for canceling the variation of the differential amplifier. The output variation referred to input was reduced to 1/30 compared with that of the prior circuit. Moreover, the residual variation of output voltage was reduced by CDS operation in ADC and stable output data was obtained with ambient temperature variation. With these improvements, the sensitivity variation of the FPA was improved to 10% in the range of -30 degrees to 80 degrees and noise equivalent temperature difference (NETD) of 40 mK was achieved.

  15. Studying the mechanism of neurostimulation by infrared laser light using GCaMP6s and Rhodamine B imaging

    NASA Astrophysics Data System (ADS)

    Moreau, David; Lefort, Claire; Bardet, Sylvia M.; O'Connor, Rodney P.

    2016-03-01

    Infrared laser light radiation can be used to depolarize neurons and to stimulate neural activity. The absorption of infrared radiation and heating of biological tissue is thought to be the underlying mechanism of this phenomenon whereby local temperature increases in the plasma membrane of cells either directly influence membrane properties or act via temperature sensitive ion channels. Action potentials are typically measured electrically in neurons with microelectrodes, but they can also be observed using fluorescence microscopy techniques that use synthetic or genetically encoded calcium indicators. In this work, we studied the impact of infrared laser light on neuronal calcium signals to address the mechanism of these thermal effects. Cultured primary mouse hippocampal neurons expressing the genetically encoded calcium indicator GCaMP6s were used in combination with the temperature sensitive fluorophore Rhodamine B to measure calcium signals and temperature changes at the cellular level. Here we present our all-optical strategy for studying the influence of infrared laser light on neuronal activity.

  16. Simulate the volcanic radiation features in medium wave infrared channels

    NASA Astrophysics Data System (ADS)

    Gong, Cailan; Jiang, Shan; Liu, Fengyi; Hu, Yong

    2015-10-01

    There are different scales and intensities of the volcanic eruption in the world every year. Existing medium wave infrared (MWI) remote sensing channels are often at atmospheric window in 3-5μm, lack of water vapor and carbon dioxide(CO2) absorption channels data, such as 2.2μm, 2.7μm and so on, however the 2.7μm absorption bands can be used as volcanoes, forest fires and other hot target identification. In order to obtain the high-temperature targets (HTT)radiation features, such as volcanic eruptions and forest fires in the water vapor absorption channels, Firstly, the HTT should be identified from the existing bands based on the temperature differences between the objects and the surrounding environment. Then, the HTT radiation features were simulated, and the correlation between the radiations of different bands were established with statistical analysis method. The HTT reorganization from remote sensing data, radiation characteristics simulation in different atmospheric models were described, then the bands transformed models were set up. The volcanic HTT radiation characteristics were simulated in wavelength 2.7μm and 4.433-4.498μm (band 24 of MODIS) based on the known bands of 3.55 -3.93μm (band 3 of FengYun-3 Visible and Infrared Scanning Radiometer (VIRR)). The simulated results were tested by the volcanic HTT radiation characteristics with 4.433-4.498μm by known bands of MODIS image and the simulated 4.433-4.498μm image. The causes of errors generated were analyzed. The study methods were useful to the new remote sensor bands imaging characteristics simulation analysis.

  17. Near-infrared induced optical quenching effects on mid-infrared quantum cascade lasers

    NASA Astrophysics Data System (ADS)

    Guo, Dingkai; Cai, Hong; Talukder, Muhammad Anisuzzaman; Chen, Xing; Johnson, Anthony M.; Khurgin, Jacob B.; Choa, Fow-Sen

    2014-06-01

    In space communications, atmospheric absorption and Rayleigh scattering are the dominant channel impairments. Transmission using mid-infrared (MIR) wavelengths offers the benefits of lower loss and less scintillation effects. In this work, we report the telecom wavelengths (1.55 μm and 1.3 μm) induced optical quenching effects on MIR quantum cascade lasers (QCLs), when QCLs are operated well above their thresholds. The QCL output power can be near 100% quenched using 20 mW of near-infrared (NIR) power, and the quenching effect depends on the input NIR intensity as well as wavelength. Time resolved measurement was conducted to explore the quenching mechanism. The measured recovery time is around 14 ns, which indicates that NIR generated electron-hole pairs may play a key role in the quenching process. The photocarrier created local field and band bending can effectively deteriorate the dipole transition matrix element and quench the QCL. As a result, MIR QCLs can be used as an optical modulator and switch controlled by NIR lasers. They can also be used as "converters" to convert telecom optical signals into MIR optical signals.

  18. Near-infrared induced optical quenching effects on mid-infrared quantum cascade lasers

    SciTech Connect

    Guo, Dingkai Talukder, Muhammad Anisuzzaman; Chen, Xing; Cai, Hong; Johnson, Anthony M.; Choa, Fow-Sen; Khurgin, Jacob B.

    2014-06-23

    In space communications, atmospheric absorption and Rayleigh scattering are the dominant channel impairments. Transmission using mid-infrared (MIR) wavelengths offers the benefits of lower loss and less scintillation effects. In this work, we report the telecom wavelengths (1.55 μm and 1.3 μm) induced optical quenching effects on MIR quantum cascade lasers (QCLs), when QCLs are operated well above their thresholds. The QCL output power can be near 100% quenched using 20 mW of near-infrared (NIR) power, and the quenching effect depends on the input NIR intensity as well as wavelength. Time resolved measurement was conducted to explore the quenching mechanism. The measured recovery time is around 14 ns, which indicates that NIR generated electron-hole pairs may play a key role in the quenching process. The photocarrier created local field and band bending can effectively deteriorate the dipole transition matrix element and quench the QCL. As a result, MIR QCLs can be used as an optical modulator and switch controlled by NIR lasers. They can also be used as “converters” to convert telecom optical signals into MIR optical signals.

  19. The TIROS-N high resolution infrared radiation sounder

    NASA Technical Reports Server (NTRS)

    Koenig, E. W.

    1979-01-01

    The high-resolution infrared radiation sounder (HIRS/2) was developed and flown on the Television and Infrared Observation Satellite, N Series (TIROS-N) as one means of obtaining atmospheric vertical profile information. The HIRS/2 receives visible and infrared spectrum radiation through a single telescope and selects 20 narrow spectral channels by means of a rotating filter wheel. A passive radiant cooler provides an operating temperature of 106.7K for the HgCdTe and InSb detectors while the visible detector operates at instrument frame temperature. Low noise amplifiers and digital processing provide 13 bit data for spacecraft data multiplexing and transmission. The qualities of system performance that determine sounding capability are the dynamic range of data collection, the noise equivalent radiance of the system, the registration of the air columns sampled in each channel, and the ability to upgrade the calibration of the instrument to maintain the performance standard throughout life. The basic performance of the instrument in test is described. Early orbital information from the TIROS-N launched on October 13, 1978 are given and some observations on system quality are made.

  20. Cascaded frequency doublers for broadband laser radiation

    SciTech Connect

    Andreev, N F; Vlasova, K V; Davydov, V S; Kulikov, S M; Makarov, A I; Sukharev, Stanislav A; Freidman, Gennadii I; Shubin, S V

    2012-10-31

    A new scheme of a cascaded converter of the first harmonic of broadband cw laser radiation into the second harmonic (SH) with compensation for the group walk-off in cascades is proposed and investigated. The conditions under which high conversion coefficients of broadband ({approx}33 cm{sup -1}) single-mode fibre laser radiation with low peak power ({approx}300 W) into the SH are determined for frequency doublers based on the most promising LBO crystal. Conversion of cw radiation with an average power of 300 W and efficiency {eta} = 4.5 % into the SH is obtained in a single LBO crystal. Effect of coherent addition of SH radiation excited in different cascades is demonstrated for two- and three-stage schemes. The expected conversion efficiencies, calculated disregarding loss but taking into account real aberrations of elements, are 18 % and 38 %, respectively. The effect of pumping depletion begins to manifest itself in the third cascade of a three-stage converter; it may reduce the latter value to {approx}30 %. (nonlinear optical phenomena)

  1. Radiative efficiency of MOCVD grown QD lasers

    NASA Astrophysics Data System (ADS)

    Mawst, Luke; Tsvid, Gene; Dudley, Peter; Kirch, Jeremy; Park, J. H.; Kim, N.

    2010-02-01

    The optical spectral gain characteristics and overall radiative efficiency of MOCVD grown InGaAs quantum dot lasers have been evaluated. Single-pass, multi-segmented amplified spontaneous emission measurements are used to obtain the gain, absorption, and spontaneous emission spectra in real units. Integration of the calibrated spontaneous emission spectra then allows for determining the overall radiative efficiency, which gives important insights into the role which nonradiative recombination plays in the active region under study. We use single pass, multi-segmented edge-emitting in which electrically isolated segments allow to vary the length of a pumped region. In this study we used 8 section devices (the size of a segment is 50x300 μm) with only the first 5 segments used for varying the pump length. The remaining unpumped segments and scribed back facet minimize round trip feedback. Measured gain spectra for different pump currents allow for extraction of the peak gain vs. current density, which is fitted to a logarithmic dependence and directly compared to conventional cavity length analysis, (CLA). The extracted spontaneous emission spectrum is calibrated and integrated over all frequencies and modes to obtain total spontaneous radiation current density and radiative efficiency, ηr. We find ηr values of approximately 17% at RT for 5 stack QD active regions. By contrast, high performance InGaAs QW lasers exhibit ηr ~50% at RT.

  2. Cascaded frequency doublers for broadband laser radiation

    NASA Astrophysics Data System (ADS)

    Andreev, N. F.; Vlasova, K. V.; Davydov, V. S.; Kulikov, S. M.; Makarov, A. I.; Sukharev, Stanislav A.; Freidman, Gennadii I.; Shubin, S. V.

    2012-10-01

    A new scheme of a cascaded converter of the first harmonic of broadband cw laser radiation into the second harmonic (SH) with compensation for the group walk-off in cascades is proposed and investigated. The conditions under which high conversion coefficients of broadband (~33 cm-1) single-mode fibre laser radiation with low peak power (~300 W) into the SH are determined for frequency doublers based on the most promising LBO crystal. Conversion of cw radiation with an average power of 300 W and efficiency η = 4.5 % into the SH is obtained in a single LBO crystal. Effect of coherent addition of SH radiation excited in different cascades is demonstrated for two- and three-stage schemes. The expected conversion efficiencies, calculated disregarding loss but taking into account real aberrations of elements, are 18 % and 38 %, respectively. The effect of pumping depletion begins to manifest itself in the third cascade of a three-stage converter; it may reduce the latter value to ~30 %.

  3. Single- and multiphoton infrared laser spectroscopy of atomic negative ions

    NASA Astrophysics Data System (ADS)

    Scheer, Michael

    A pulsed, tunable infrared laser source (0.6-5.2 μm) has been developed on the basis of a commercial dye laser and non-linear optical conversion techniques. This laser source was combined with a keV negative ion beam apparatus in a crossed-beam geometry, with the aim to systematically study several atomic negative ions through a variety of single- and multiphoton detachment experiments. Photodetachment threshold spectra of 21 ionic species (B- , C-, O-, Al- , Si-, Cr-, Co- , Ni-, Cu-, Ge- , Mo-, Rh-, Pd- , Ag-, Sn-, Sb- , Te-, Cs-, Ir- , Pt-, and Bi-) have been recorded, in most cases resulting in very accurate determinations of ionic binding energies, marking substantial improvements over previous experimental values. In fact, several ionic states investigated here had not been observed previously. Different schemes for resonant multiphoton detachment of atomic negative ions were demonstrated for the first time. These studies were conducted with several anions (Si-, Sri- , Sb-, Te-, Ir- , and Pt-) providing highly accurate ionic energy level splittings and clearly demonstrating that multiphoton probes are generally applicable to negative ion structure.

  4. Infrared laser ablation atmospheric pressure photoionization mass spectrometry.

    PubMed

    Vaikkinen, Anu; Shrestha, Bindesh; Kauppila, Tiina J; Vertes, Akos; Kostiainen, Risto

    2012-02-01

    In this paper we introduce laser ablation atmospheric pressure photoionization (LAAPPI), a novel atmospheric pressure ion source for mass spectrometry. In LAAPPI the analytes are ablated from water-rich solid samples or from aqueous solutions with an infrared (IR) laser running at 2.94 μm wavelength. Approximately 12 mm above the sample surface, the ablation plume is intercepted with an orthogonal hot solvent (e.g., toluene or anisole) jet, which is generated by a heated nebulizer microchip and directed toward the mass spectrometer inlet. The ablated analytes are desolvated and ionized in the gas-phase by atmospheric pressure photoionization using a 10 eV vacuum ultraviolet krypton discharge lamp. The effect of operational parameters and spray solvent on the performance of LAAPPI is studied. LAAPPI offers ~300 μm lateral resolution comparable to, e.g., matrix-assisted laser desorption ionization. In addition to polar compounds, LAAPPI efficiently ionizes neutral and nonpolar compounds. The bioanalytical application of the method is demonstrated by the direct LAAPPI analysis of rat brain tissue sections and sour orange (Citrus aurantium) leaves. PMID:22242626

  5. Design of stabilization system for medium wave infrared laser power

    NASA Astrophysics Data System (ADS)

    Ding, Zhong-kui; Wang, Lin; Shi, Xue-shun; Xu, Jun

    2013-12-01

    The 3~5um Medium Wave Infrared(MWIR) laser has gained a lot of attention for its important application values in remote sensing, medical, military and many other fields. However, there are many technical difficulties to fabricate those kind lasers, and the performance of their output power stabilities remain to be improved. In a practical application, the MWIR's output power will be instability when the temperature changes and the current varies. So a system of reducing MWIR power fluctuation should be established. In this paper, a photoelectric system of stabilizing the output power of He-Ne laser is developed, which is designed based on the theory of feedback control. Some primary devices and technologies are presented and the functions of each module are described in detail. Among of those, an auxiliary visible light path is designed to aid to adjust WMIR optical system. A converging lens as spatial filter is employed to eliminate stray light well. Dewar temperature control equipment is also used to reduce circuit noise in IR detector. The power supply of AD conversion circuit is independently designed to avoid the crosstalk caused by the analog section and digital section. Then the system has the advantages of good controllability, stability and high precision after above designation. Finally, the measurement precision of the system is also analyzed and verified.

  6. DEVELOPMENT OF NEW MID-INFRARED ULTRAFAST LASER SOURCES FOR COMPACT COHERENT X-RAY SOURCES

    SciTech Connect

    Sterling Backus

    2012-05-14

    In this project, we proposed to develop laser based mid-infrared lasers as a potentially robust and reliable source of ultrafast pulses in the mid-infrared region of the spectrum, and to apply this light source to generating bright, coherent, femtosecond-to-attosecond x-ray beams.

  7. Electro-optic modulator for infrared laser using gallium arsenide crystal

    NASA Technical Reports Server (NTRS)

    Walsh, T. E.

    1968-01-01

    Gallium arsenide electro-optic modulator used for infrared lasers has a mica quarter-wave plate and two calcite polarizers to amplitude or phase modulate an infrared laser light source in the wavelength range from 1 to 3 microns. The large single crystal has uniformly high resistivities, is strain free, and comparable in quality to good optical glass.

  8. Argon laser treatment of radiation proctitis

    SciTech Connect

    O'Connor, J.J.

    1989-06-01

    Radiation therapy for malignant gynecologic disease and prostatic cancer has resulted in increased survival and cure rates. This modality has unfortunately produced debilitating radiation proctitis. Recently, five patients were seen with continuous rectal bleeding secondary to radiation disease of the rectum. Four of these patients were women who were being treated for cervical carcinoma and one was a man with prostatic cancer. These patients were refractory to steroid retention enemas, iron therapy, and benproperine enema therapy. Treatment was accomplished using the argon laser with a 300-micron fiber passed via flexible fiberoptic sigmoidoscope. The most proximal areas were treated first. One and a half watts at 0.5 pulses was used. Up to 50 pulses were delivered per therapy session. The fiber was placed in contact with the lesion and circumferentially for 0.5 cm surrounding each suspected area. Bleeding stopped in the four women after two sessions and in the man after four sessions.

  9. Dy{sup 3+}-doped Ga–Sb–S chalcogenide glasses for mid-infrared lasers

    SciTech Connect

    Zhang, Mingjie; Yang, Anping; Peng, Yuefeng; Zhang, Bin; Ren, He; Guo, Wei; Yang, Yan; Zhai, Chengcheng; Wang, Yuwei; Yang, Zhiyong; Tang, Dingyuan

    2015-10-15

    Highlights: • Novel Ga–Sb–S chalcogenide glasses doped with Dy{sup 3+} ions were synthesized. • The glasses show good thermal stability and excellent infrared transparency. • The glasses show low phonon energy and intense mid-infrared emissions. • The mid-infrared emissions have high quantum efficiency. • The mid-infrared emissions have large stimulated emission cross sections. - Abstract: Novel Ga–Sb–S chalcogenide glasses doped with different amount of Dy{sup 3+} ions were prepared. Their thermal stability, optical properties, and mid-infrared (MIR) emission properties were investigated. The glasses show good thermal stability, excellent infrared transparency, very low phonon energy (∼306 cm{sup −1}), and intense emissions centered at 2.95, 3.59, 4.17 and 4.40 μm. Three Judd–Ofelt intensity parameters (Ω{sub 2} = 8.51 × 10{sup −20} cm{sup 2}, Ω{sub 4} = 2.09 × 10{sup −20} cm{sup 2}, and Ω{sub 6} = 1.60 × 10{sup −20} cm{sup 2}) are obtained, and the related radiative transition properties are evaluated. The high quantum efficiencies and large stimulated emission cross sections of the MIR emissions (88.10% and 1.11 × 10{sup −20} cm{sup 2} for 2.95 μm emission, 75.90% and 0.38 × 10{sup −20} cm{sup 2} for 4.40 μm emission, respectively) in the Dy{sup 3+}-doped Ga–Sb–S glasses make them promising gain materials for the MIR lasers.

  10. Laser-plasma accelerators-based high energy radiation femtochemistry and spatio-temporal radiation biomedicine

    NASA Astrophysics Data System (ADS)

    Gauduel, Y. A.; Lundh, O.; Martin, M. T.; Malka, V.

    2012-06-01

    The innovating advent of powerful TW laser sources (~1019 W cm-z) and laser-plasma interactions providing ultra-short relativistic particle beams (electron, proton) in the MeV domain open exciting opportunities for the simultaneous development of high energy radiation femtochemistry (HERF) and ultrafast radiation biomedicine. Femtolysis experiments (Femtosecond radiolysis) of aqueous targets performed with relativistic electron bunches of 2.5-15 MeV give new insights on transient physicochemical events that take place in the prethermal regime of confined ionization tracks. Femtolysis studies emphasize the pre-eminence of ultra-fast quantum effects in the temporal range 10-14 - 10-11 s. The most promising advances of HERF concern the quantification of ultrafast sub-nanometric biomolecular damages (bond weakening and bond breaking) in the radial direction of a relativistic particle beam. Combining ultra-short relativistic particle beams and near-infrared spectroscopic configurations, laser-plasma accelerators based high energy radiation femtochemistry foreshadows the development of real-time radiation chemistry in the prethermal regime of nascent ionisation clusters. These physico-chemical advances would be very useful for future developments in biochemically relevant environments (DNA, proteins) and in more complex biological systems such as living cells. The first investigation of single and multiple irradiation shots performed at high energy level (90 MeV) and very high dose rate, typically 1013 Gy s-1, demonstrates that measurable assessments of immediate and reversible DNA damage can be explored at single cell level. Ultrafast in vivo irradiations would permit the development of bio-nanodosimetry on the time scale of molecular motions, i.e. angstrom or sub-angstrom displacements and open new perspectives in the emerging domain of ultrafast radiation biomedicine such as pulsed radiotherapy.

  11. Local changes in arterial oxygen saturation induced by visible and near-infrared light radiation.

    PubMed

    Yesman, S S; Mamilov, S O; Veligotsky, D V; Gisbrecht, A I

    2016-01-01

    In this study, we investigate the efficiency of laser radiation on oxyhemoglobin (HbO2) rate in blood vessels and its wavelength dependence. The results of in vivo experimental measurements of the laser-induced photodissociation of HbO2 in cutaneous blood vessels in the visible and near-infrared (IR) spectral range are presented. Arterial oxygen saturation (SpO2) was measured by a method of fingertip pulse oximetry, which is based on the measurement of the modulated pulse wave of the blood. The light irradiating the finger was provided by corresponding light-emitting diodes (LED) at 15 wavelengths in the 400-940 nm spectrum range. Statistical results with a value of p < 0.05 were viewed as being significant for all volunteers. The results show that there is a decrease in SpO2 in the blood under the influence of the transcutaneous laser irradiation. Three maxima in the spectral range (530, 600, and 850 nm) are revealed, wherein decrease in the relative concentration of SpO2 reaches 5 % ± 0.5 %. Near-IR radiation plays a dominant role in absorption of laser radiation by oxyhemoglobin in deeper layers of tissue blood vessels. The obtained data correlate with the processes of light propagation in biological tissue. The observed reduction in SpO2 indicates the process of photodissociation of HbO2 in vivo and may result in local increase in O2 in the tissue. Such laser-induced enrichment of tissue oxygenation can be used in phototherapy of pathologies, where the elimination of local tissue hypoxia is critical. PMID:26637304

  12. Laser radiation action on the biomedium as nonadiabatic excitation of macromolecules

    NASA Astrophysics Data System (ADS)

    Kompanets, Igor N.; Krasnov, Andrey E.; Malov, A. N.

    1996-11-01

    The extended sphere of the laser successful use at large vagueness of the gear of radiation interaction with biological and biosimilar objects is a main modern paradox in the application of low-intensity coherent radiation in biology and medicine. There are rather regularly, for example, the reasons of immateriality of such parameters as laser radiation coherency degree for biostimulation, but the replacement of semi-conductor lasers by the light diodes isn't observed in medical practice until now. there are also no convincing results on comparative analysis of biostimulated effect under coherent and noncoherent radiation. Action of coherent electromagnetic radiation of the visible and infrared spectral range causes, as appear, the same type structure-optical changes in various objects biological liquids, cells suspensions, model biomolecular solutions, cells of plan, insects and animals. The medicobiologic consequences of laser effect are extremely variable because of the complexity of biological object and sophistication of research techniques and analyses. The energy doze of radiation acting onto a bio-object, as a rule, is extremely small, and hence like the case of extremely high frequency radiation one can to name this action by the 'informative' one, i.e., initiating only biosystem reactions is produced due to its own energy. In connection with the relatively slow biosystem response to the laser radiation action, the nonlocality of this reaction at the local action and large variety of biochemical reactions caused with laser radiation one can assume the existence of uniform physical mechanism realizing the biostimulation effect of laser radiation for various biosystems.

  13. Generation of blue light by intracavity frequency mixing of the laser and pump radiation of a miniature neodymium:yttrium aluminum garnet laser

    SciTech Connect

    Risk, W.P.; Baumert, J.; Bjorklund, G.C.; Schellenberg, F.M.; Lenth, W.

    1988-01-11

    Potassium titanyl phosphate (KTiOPO/sub 4/,KTP) has been used to generate blue 459-nm radiation by intracavity sum frequency mixing of the circulating 1064-nm laser radiation of a miniature neodymium:yttrium aluminum garnet laser and the 809-nm radiation used as the pump source. A blue output power of approximately 1 mW cw was obtained using 275 mW of pump power from an infrared dye laser. Gain-switched operation leading to high 459-nm peak powers was demonstrated. Direct rapid modulation of the blue radiation was achieved by modulating the pump. In preliminary experiments a high-power laser diode was used as the pump source for the generation of blue radiation.

  14. High-power metal halide vapour lasers oscillating in deep ultraviolet, visible and middle infrared spectral ranges

    NASA Astrophysics Data System (ADS)

    Temelkov, K. A.; Slaveeva, S. I.; Kirilov, V. I.; Kostadinov, I. K.; Vuchkov, N. K.

    2012-05-01

    Middle infrared and deep ultraviolet high-power high-beam-quality stable-operating He-SrBr2 and Cu+ Ne-CuBr lasers excited in nanosecond pulsed longitudinal discharge are developed, patented and studied. Optimal discharge conditions, such as active zone diameter, vapour pressure, buffer-gas pressure, electrical excitation scheme parameters, average input power and pulse repetition frequency, are found. The highest output laser parameters are obtained for the Sr atom and Cu+ lasers, respectively. These lasers equipped with optical systems for the control of laser radiation parameters are used in a large variety of applications, such as precise material microprocessing, including biological tissues, determination of linear optical properties of different newly developed materials, laser-induced modification of conductive polymers and laser-induced fluorescence in wide-gap semiconductors, instead of free electron and excimer lasers, respectively. A master oscillator-power amplifier system, which is based on a high-beam-quality high-power CuBr vapour laser and is equipped with an optic system for laser beam control and with the X-Y stage controlled by adequate software as well, is developed and used in high-precision micromachining of samples made of nickel and tool steel.

  15. A Fast Infrared Radiative Transfer Model for Overlapping Clouds

    NASA Technical Reports Server (NTRS)

    Niu, Jianguo; Yang, Ping; Huang, Huang-Lung; Davies, James E.; Li, Jun; Baum, Bryan A.; Hu, Yong X.

    2006-01-01

    A fast infrared radiative transfer model (FIRTM2) appropriate for application to both single-layered and overlapping cloud situations is developed for simulating the outgoing infrared spectral radiance at the top of the atmosphere (TOA). In FIRTM2 a pre-computed library of cloud reflectance and transmittance values is employed to account for one or two cloud layers, whereas the background atmospheric optical thickness due to gaseous absorption can be computed from a clear-sky radiative transfer model. FIRTM2 is applicable to three atmospheric conditions: 1) clear-sky, 2) single-layered ice or water cloud, and 3) two simultaneous cloud layers in a column (e.g., ice cloud overlying water cloud). Moreover, FIRTM2 outputs the derivatives (i.e., Jacobians) of the TOA brightness temperature with respect to cloud optical thickness and effective particle size. Sensitivity analyses have been carried out to assess the performance of FIRTM2 for two spectral regions, namely the longwave (LW) band (587.3 - 1179.5/cm) and the short-to-medium wave (SMW) band (1180.1 - 2228.9/cm). The assessment is carried out in terms of brightness temperature differences (BTD) between FIRTM2 and the well-known discrete ordinates radiative transfer model (DISORT), henceforth referred to as BTD (F-D). The BTD (F-D) values for single-layered clouds are generally less than 0.8 K. For the case of two cloud layers (specifically ice cloud over water cloud), the BTD(F-D) values are also generally less than 0.8 K except for the SMW band for the case of a very high altitude (>15 km) cloud comprised of small ice particles. Note that for clear-sky atmospheres, FIRTM2 reduces to the clear-sky radiative transfer model that is incorporated into FIRTM2, and the errors in this case are essentially those of the clear-sky radiative transfer model.

  16. Atmospheric influences on infrared-laser signals used for occultation measurements between Low Earth Orbit satellites

    NASA Astrophysics Data System (ADS)

    Schweitzer, S.; Kirchengast, G.; Proschek, V.

    2011-10-01

    LEO-LEO infrared-laser occultation (LIO) is a new occultation technique between Low Earth Orbit (LEO) satellites, which applies signals in the short wave infrared spectral range (SWIR) within 2 μm to 2.5 μm. It is part of the LEO-LEO microwave and infrared-laser occultation (LMIO) method that enables to retrieve thermodynamic profiles (pressure, temperature, humidity) and altitude levels from microwave signals and profiles of greenhouse gases and further variables such as line-of-sight wind speed from simultaneously measured LIO signals. Due to the novelty of the LMIO method, detailed knowledge of atmospheric influences on LIO signals and of their suitability for accurate trace species retrieval did not yet exist. Here we discuss these influences, assessing effects from refraction, trace species absorption, aerosol extinction and Rayleigh scattering in detail, and addressing clouds, turbulence, wind, scattered solar radiation and terrestrial thermal radiation as well. We show that the influence of refractive defocusing, foreign species absorption, aerosols and turbulence is observable, but can be rendered small to negligible by use of the differential transmission principle with a close frequency spacing of LIO absorption and reference signals within 0.5%. The influences of Rayleigh scattering and terrestrial thermal radiation are found negligible. Cloud-scattered solar radiation can be observable under bright-day conditions, but this influence can be made negligible by a close time spacing (within 5 ms) of interleaved laser-pulse and background signals. Cloud extinction loss generally blocks SWIR signals, except very thin or sub-visible cirrus clouds, which can be addressed by retrieving a cloud layering profile and exploiting it in the trace species retrieval. Wind can have a small influence on the trace species absorption, which can be made negligible by using a simultaneously retrieved or a moderately accurate background wind speed profile. We conclude that

  17. Structural alterations in the cornea from exposure to infrared radiation. Final report, 1 April 1986-14 April 1988

    SciTech Connect

    Farrall, R.A.; McCally, R.L.; Bargeron, C.B.; Green, W.R.

    1989-08-01

    This report summarizes our research on the interaction of infrared radiation, especially from high-intensity CO{sub 2} TEA lasers, with the cornea. The research reported here was performed between April 1, 1986 and April 14 1988. The report discusses threshold epithelial damage from single- and multiple-pulse exposures, material ejection from the anterior corneal surface, lesion histology, and possible damage mechanisms.

  18. Frequency doubling of fiber laser radiation of large spectral bandwidths

    NASA Astrophysics Data System (ADS)

    Nyga, Sebastian; Geiger, Jens; Jungbluth, Bernd

    2010-02-01

    In this work the reduction of conversion efficiency due to spectral bandwidth of fiber laser radiation is investigated. Subsequently, compensation optics to correct the spectral phase mismatching inside the nonlinear crystal is dimensioned and tested. For the experimental study a laboratory fiber laser setup is used consisting of a seed diode and a three stage fiber amplifier. The laser delivers an average output power of up to 100 W at 1 MHz. Even below the Raman threshold the output is far away from Fourier limit, providing a nearly Lorentzian spectral shape and a temporal pulse width of 800 ps. As the bandwidth increases nearly linearly with the pump power of the third amplifier stage, this parameter could be controlled for the experiments. All conversion experiments are conducted with a moderate load of the nonlinear crystals, i.e. intensity less than 150 MW/cm2. Without compensation of the spectral phase mismatch, a maximum conversion efficiency of 15 % is attained for a Type I configuration with a 20mm long LBO crystal. Using the compensation setup 27 W of green light are obtained from 60 W infrared light at a bandwidth of 4.7 nm. Therefore the efficiency rises to 44% at the same load.

  19. Retinal safety of near infrared radiation in photovoltaic restoration of sight.

    PubMed

    Lorach, H; Wang, J; Lee, D Y; Dalal, R; Huie, P; Palanker, D

    2016-01-01

    Photovoltaic restoration of sight requires intense near-infrared light to effectively stimulate retinal neurons. We assess the retinal safety of such radiation with and without the retinal implant. Retinal damage threshold was determined in pigmented rabbits exposed to 880nm laser radiation. The 50% probability (ED50) of retinal damage during 100s exposures with 1.2mm diameter beam occurred at 175mW, corresponding to a modeled temperature rise of 12.5°C. With the implant, the same temperature was reached at 78mW, close to the experimental ED50 of 71mW. In typical use conditions, the retinal temperature rise is not expected to exceed 0.43°C, well within the safety limits for chronic use. PMID:26819813

  20. Retinal safety of near infrared radiation in photovoltaic restoration of sight

    PubMed Central

    Lorach, H.; Wang, J.; Lee, D. Y.; Dalal, R.; Huie, P.; Palanker, D.

    2015-01-01

    Photovoltaic restoration of sight requires intense near-infrared light to effectively stimulate retinal neurons. We assess the retinal safety of such radiation with and without the retinal implant. Retinal damage threshold was determined in pigmented rabbits exposed to 880nm laser radiation. The 50% probability (ED50) of retinal damage during 100s exposures with 1.2mm diameter beam occurred at 175mW, corresponding to a modeled temperature rise of 12.5°C. With the implant, the same temperature was reached at 78mW, close to the experimental ED50 of 71mW. In typical use conditions, the retinal temperature rise is not expected to exceed 0.43°C, well within the safety limits for chronic use. PMID:26819813

  1. Analytical Characterization of CFRP Laser Treated by Excimer Laser Radiation

    NASA Astrophysics Data System (ADS)

    Kreling, S.; Fischer, F.; Delmdahl, R.; Gäbler, F.; Dilger, K.

    Due to the increasing interest in lightweight structures, carbon-fiber reinforced plastics are increasingly applied, especially in the transportation industry. An interesting technology for joining these materials is adhesive bonding due to numerous advantages compared to conventional techniques like riveting. However, to achieve a strong and durable bond, surface pre-treatment is necessary to remove residues of release agents that are transferred to the surface during manufacturing. This paper describes analytical experiments, namely SEM and XPS, performed on CFRP surfaces pre-treated with 308 nm excimer laser radiation.

  2. Stratospheric aerosol properties and their effects on infrared radiation.

    NASA Technical Reports Server (NTRS)

    Remsberg, E. E.

    1973-01-01

    This paper presents a stratospheric aerosol model and infers its effects on terrestrial radiation. Composition of the aerosol is assumed to be concentrated sulfuric acid. An appropriate size distribution has been determined from available size distribution measurements of other investigators. Aerosols composed of concentrated sulfuric acid emit energy in the atmospheric window region of the infrared spectrum, 8-13 microns. Laboratory measurements of optical constant data obtained at room temperature are presented for 75 and 90% aqueous sulfuric acid. Calculations of an aerosol extinction coefficient are then performed by using the above data. Effects of changes in aerosol phase and temperature are discussed but not resolved.

  3. Ultraviolet versus infrared: Effects of ablation laser wavelength on the expansion of laser-induced plasma into one-atmosphere argon gas

    NASA Astrophysics Data System (ADS)

    Ma, Qianli; Motto-Ros, Vincent; Laye, Fabrice; Yu, Jin; Lei, Wenqi; Bai, Xueshi; Zheng, Lijuan; Zeng, Heping

    2012-03-01

    Laser-induced plasma from an aluminum target in one-atmosphere argon background has been investigated with ablation using nanosecond ultraviolet (UV: 355 nm) or infrared (IR: 1064 nm) laser pulses. Time- and space-resolved emission spectroscopy was used as a diagnostics tool to have access to the plasma parameters during its propagation into the background, such as optical emission intensity, electron density, and temperature. The specific feature of nanosecond laser ablation is that the pulse duration is significantly longer than the initiation time of the plasma. Laser-supported absorption wave due to post-ablation absorption of the laser radiation by the vapor plume and the shocked background gas plays a dominant role in the propagation and subsequently the behavior of the plasma. We demonstrate that the difference in absorption rate between UV and IR radiations leads to different propagation behaviors of the plasma produced with these radiations. The consequence is that higher electron density and temperature are observed for UV ablation. While for IR ablation, the plasma is found with lower electron density and temperature in a larger and more homogenous axial profile. The difference is also that for UV ablation, the background gas is principally evacuated by the expansion of the vapor plume as predicted by the standard piston model. While for IR ablation, the background gas is effectively mixed to the ejected vapor at least hundreds of nanoseconds after the initiation of the plasma. Our observations suggest a description by laser-supported combustion wave for the propagation of the plasma produced by UV laser, while that by laser-supported detonation wave for the propagation of the plasma produced by IR laser. Finally, practical consequences of specific expansion behavior for UV or IR ablation are discussed in terms of analytical performance promised by corresponding plasmas for application with laser-induced breakdown spectroscopy.

  4. Laser cooling by collisional redistribution of radiation.

    PubMed

    Vogl, Ulrich; Weitz, Martin

    2009-09-01

    The general idea that optical radiation may cool matter was put forward 80 years ago. Doppler cooling of dilute atomic gases is an extremely successful application of this concept. More recently, anti-Stokes cooling in multilevel systems has been explored, culminating in the optical refrigeration of solids. Collisional redistribution of radiation has been proposed as a different cooling mechanism for atomic two-level systems, although experimental investigations using moderate-density gases have not reached the cooling regime. Here we experimentally demonstrate laser cooling of an atomic gas based on collisional redistribution of radiation, using rubidium atoms in argon buffer gas at a pressure of 230 bar. The frequent collisions in the ultradense gas transiently shift a highly red-detuned laser beam (that is, one detuned to a much lower frequency) into resonance, whereas spontaneous decay occurs close to the unperturbed atomic resonance frequency. During each excitation cycle, kinetic energy of order k(B)T-that is, the thermal energy (k(B), Boltzmann's constant; T, temperature)-is extracted from the dense atomic sample. In a proof-of-principle experiment with a thermally non-isolated sample, we demonstrate relative cooling by 66 K. The cooled gas has a density more than ten orders of magnitude greater than the typical values used in Doppler-cooling experiments, and the cooling power reaches 87 mW. Future applications of the technique may include supercooling beyond the homogeneous nucleation temperature and optical chillers. PMID:19727195

  5. Mid-wave/long-wave infrared lasers and their sensing applications

    NASA Astrophysics Data System (ADS)

    Law, K. K.; Shori, R.; Miller, J. K.; Sharma, S.

    2011-06-01

    Many advances have been made recently in both solid-state and semiconductor based mid-wave infrared (MWIR) and long-wave infrared (LWIR) laser technologies, and there is an ever growing demand for these laser sources for Naval, DOD and homeland security applications. We will present various current and future programs and efforts at Naval Air Warfare Center Weapons Division (NAWCWD) on the development of high-power, broadly tunable MWIR/LWIR lasers for sensing applications.

  6. Chalcogenide fiber for mid-infrared transmission and generation of laser source

    NASA Astrophysics Data System (ADS)

    Chenard, Francois; Kuis, Robinson A.

    2010-04-01

    Chalcogenide glass fibers are the best candidates for mid-infrared transmission. Their low optical losses and high-power damage threshold are enabling numerous applications: laser power delivery, chemical sensing and imaging. Furthermore, chalcogenide glass fibers are best candidates for demonstrating rare-earth doped fiber lasers and supercontinuum sources in the mid-infrared. The latest results towards the creation of a 4.5 micron fiber laser and a broadband (2-5 micron) supercontinuum source are presented.

  7. Coherent microwave radiation from a laser induced plasma

    SciTech Connect

    Shneider, M. N.; Miles, R. B.

    2012-12-24

    We propose a method for generation of coherent monochromatic microwave/terahertz radiation from a laser-induced plasma. It is shown that small-scale plasma, located in the interaction region of two co-propagating plane-polarized laser beams, can be a source of the dipole radiation at a frequency equal to the difference between the frequencies of the lasers. This radiation is coherent and appears as a result of the so-called optical mixing in plasma.

  8. Infrared antireflection DLC films by femtosecond pulsed laser deposition

    NASA Astrophysics Data System (ADS)

    Wang, Shuyun; Guo, Yanlong; Wang, Xiaobing; Cheng, Yong; Wang, Huisheng; Liu, Xu

    2009-05-01

    Diamond-like Carbon(DLC) films are deposited by Ti:Sapphire femtosecond pulsed laser(800nm, 120fs-2ps, 3.3W, 1-1000Hz) at room temperature. The substrate is n-type Si(100), and the target is 99.999%-purity graphite. After a great lot of experiments, optimal technical parameters, which are 1000Hz repetition frequency, 120fs pulse-width, 5cm-distance between target and underlay and 1014W/cm2 power-density, were used to deposite 443nm thick DLC film. Raman spectrum measurement shows a broad peak with a center at 1550 cm-1 for all films, similar to those of typical diamond-like carbon films prepared using other methods. And sp3-bond content reaches 67% analyzed by XPS. There is no nick on the film when scraped 105 times by a RS-5600 friction test machine under the pressure of 9.8N. The infrared transmittance increases along with the oxygen pressure when between 0.03 Pa and 2 Pa. The result shows that oxygen is effective in etching sp2-bond content. The extreme infrared transmittance of Si slice deposited DLC film on single surface is higher than 64% at 3-5μm, superior to 53% when being uncoated.

  9. Deposition of polyimide precursor by resonant infrared laser ablation

    NASA Astrophysics Data System (ADS)

    Dygert, N. L.; Gies, A. P.; Schriver, K. E.; Haglund, R. F., Jr.

    2007-11-01

    We report the successful deposition of a polyimide precursor using resonant infrared laser ablation (RIR-LA). A solution of poly(amic acid) (PAA) dissolved in N-methyl-2-pyrrolidinone (NMP), the melt processable precursor to polyimide, was frozen in liquid nitrogen for use as an ablation target in a high-vacuum chamber. Fourier transform infrared spectroscopy was used to determine that the local chemical structure remained unaltered. Gel permeation chromatography demonstrated that the transferred PAA retained its molecular weight, showing that RIR-LA is able to transfer the polymer intact, with no detectable chain fragmentation. These results are in stark contrast to UV-processing which degrades the polymer. After deposition the PAA may be removed with a suitable solvent; however, once the material has undergone cyclodehydration it forms an impenetrable three-dimensional network associated with thermosetting polymers. The transfer of uncured PAA precursor supports the hypothesis that RIR-LA is intrinsically a low temperature process, because the PAA is transferred without reaching the curing temperature. The RIR-LA also effectively removes the solvent NMP from the PAA, during both the ablation and deposition phases; this is a necessary step in generating PI films.

  10. Photoacoustic-based detector for infrared laser spectroscopy

    NASA Astrophysics Data System (ADS)

    Scholz, L.; Palzer, S.

    2016-07-01

    In this contribution, we present an alternative detector technology for use in direct absorption spectroscopy setups. Instead of a semiconductor based detector, we use the photoacoustic effect to gauge the light intensity. To this end, the target gas species is hermetically sealed under excess pressure inside a miniature cell along with a MEMS microphone. Optical access to the cell is provided by a quartz window. The approach is particularly suitable for tunable diode laser spectroscopy in the mid-infrared range, where numerous molecules exhibit large absorption cross sections. Moreover, a frequency standard is integrated into the method since the number density and pressure inside the cell are constant. We demonstrate that the information extracted by our method is at least equivalent to that achieved using a semiconductor-based photon detector. As exemplary and highly relevant target gas, we have performed direct spectroscopy of methane at the R3-line of the 2v3 band at 6046.95 cm-1 using both detector technologies in parallel. The results may be transferred to other infrared-active transitions without loss of generality.

  11. Mid-infrared emission from laser-induced breakdown spectroscopy.

    PubMed

    Yang, Clayton S-C; Brown, Ei E; Hommerich, Uwe H; Trivedi, Sudhir B; Samuels, Alan C; Snyder, A Peter

    2007-03-01

    Laser-induced breakdown spectroscopy (LIBS) is a powerful analytical technique for detecting and identifying trace elemental contaminants by monitoring the visible atomic emission from small plasmas. However, mid-infrared (MIR), generally referring to the wavelength range between 2.5 to 25 microm, molecular vibrational and rotational emissions generated by a sample during a LIBS event has not been reported. The LIBS investigations reported in the literature largely involve spectral analysis in the ultraviolet-visible-near-infrared (UV-VIS-NIR) region (less than 1 microm) to probe elemental composition and profiles. Measurements were made to probe the MIR emission from a LIBS event between 3 and 5.75 microm. Oxidation of the sputtered carbon atoms and/or carbon-containing fragments from the sample and atmospheric oxygen produced CO(2) and CO vibrational emission features from 4.2 to 4.8 microm. The LIBS MIR emission has the potential to augment the conventional UV-VIS electronic emission information with that in the MIR region. PMID:17389073

  12. Infrared radiation from explosions in a spark-ignition engine

    NASA Technical Reports Server (NTRS)

    Marvin, Charles F , Jr; Caldwell, Frank R; Steele, Sydney

    1935-01-01

    This report presents the results of an investigation to determine the variations in intensity and spectral distribution of the radiant energy emitted by the flames during normal and knocking explosions in an engine. Radiation extending into the infrared was transmitted by a window of fluorite, placed either near the spark plug or over the detonation zone at opposite ends of the combustion chamber. Concave, surface-silvered mirrors focused the beam, first at the slit of a stroboscope which opened for about 2 degrees of crank angle at any desired point in the engine cycle, and then upon the target of a sensitive thermocouple for measuring radiation intensity. Spectral distribution of the radiant energy was determined by placing over the window, one at a time, a series of five filters selected with a view to identifying, as far as possible without the use of a spectrograph, the characteristic emissions of water vapor, carbon dioxide, and incandescent carbon.

  13. Fiber-delivered mid-infrared (6-7) laser ablation of retinal tissue under perfluorodecalin

    NASA Astrophysics Data System (ADS)

    Mackanos, Mark A.; Joos, Karen M.; Jansen, E. Duco

    2003-07-01

    The Er:YAG laser (l=2.94mm) is an effective tool in vitreo-retinal surgery. Pulsed mid-infrared (l=6.45 mm) radiation from the Free Electron Laser has been touted as a potentially superior cutting tool. To date, use of this laser has been limited to applications in an air environment. The goal of this study was: 1) determine feasibility of fiberoptic delivery of 6.45mm using silverhalide fibers (d=700mm); 2) use infrared transparent vitreous substitute (perfluorodecalin) to allow non-contact ablation of the retina at 6.45mm. Fiber damage threshold=7.8J/cm2 (0.54GW/cm2) while transmission loss=0.54dB/m, allowing supra-ablative radiant exposures to the target. FTIR measurements of perfluorodecalin at 6.45mm yielded ma=3mm-1. Pump-probe imaging of ablation of a tissue-phantom through perfluorodecalin showed feasibility of non-contact ablation at l=6.45mm. Ablation of the retinal membranes of enucleated pig eyes was carried out under perfluorodecalin (5 Hz, 1.3 J/cm2). Each eye was cut along its equator to expose the retina. Vitreous was replaced by perfluorodecalin and laser radiation was delivered to the retina via the silverhalide fiber. The eye was rotated (at 2 rpm) using a stepper motor (0.9o/step) to create an ablation circle around the central axis of the retina (50% spot-to-spot overlap). Histological analysis of ablation yield and collateral damage will be presented. We have shown that using l=6.45mm delivered via silver halide fibers through perfluorodecalin allowed non-contact laser ablation. Remote structures are shielded, as the radiant exposure falls below the ablation threshold owing non-negligible absorption of perfluorodecalin at 6.45mm. This may optimize efficacy and safety of laser-based vitreoretinal surgery.

  14. The influence of infrared radiation on short-term ultraviolet-radiation-induced injuries

    SciTech Connect

    Kaidbey, K.H.; Witkowski, T.A.; Kligman, A.M.

    1982-05-01

    Because heat has been reported to influence adversely short- and long-term ultraviolet (UV)-radiation-induced skin damage in animals, we investigated the short-term effects of infrared radiation on sunburn and on phototoxic reactions to topical methoxsalen and anthracene in human volunteers. Prior heating of the skin caused suppression of the phototoxic response to methoxsalen as evidenced by an increase in the threshold erythema dose. Heat administered either before or after exposure to UV radiation had no detectable influence on sunburn erythema or on phototoxic reactions provoked by anthracene.

  15. Doping of germanium and silicon crystals with non-hydrogenic acceptors for far infrared lasers

    DOEpatents

    Haller, Eugene E.; Brundermann, Erik

    2000-01-01

    A method for doping semiconductors used for far infrared lasers with non-hydrogenic acceptors having binding energies larger than the energy of the laser photons. Doping of germanium or silicon crystals with beryllium, zinc or copper. A far infrared laser comprising germanium crystals doped with double or triple acceptor dopants permitting the doped laser to be tuned continuously from 1 to 4 terahertz and to operate in continuous mode. A method for operating semiconductor hole population inversion lasers with a closed cycle refrigerator.

  16. Single frequency and wavelength stabilized near infrared laser source for water vapor DIAL remote sensing application

    NASA Astrophysics Data System (ADS)

    Chuang, Ti; Walters, Brooke; Shuman, Tim; Losee, Andrew; Schum, Tom; Puffenberger, Kent; Burnham, Ralph

    2015-02-01

    Fibertek has demonstrated a single frequency, wavelength stabilized near infrared laser transmitter for NASA airborne water vapor DIAL application. The application required a single-frequency laser transmitter operating at 935 nm near infrared (NIR) region of the water vapor absorption spectrum, capable of being wavelength seeded and locked to a reference laser source and being tuned at least 100 pm across the water absorption spectrum for DIAL on/off measurements. Fibertek is building a laser transmitter system based on the demonstrated results. The laser system will be deployed in a high altitude aircraft (ER-2 or UAV) to autonomously perform remote, long duration and high altitude water vapor measurements.

  17. Design study of a laser-cooled infrared sensor

    NASA Astrophysics Data System (ADS)

    Hehlen, Markus P.; Boncher, William L.; Love, Steven P.

    2015-03-01

    The performance of a solid-state optical refrigerator is the result of a complex interplay of numerous optical and thermal parameters. We present a first preliminary study of an optical cryocooler using ray-tracing techniques. A numerical optimization identified a non-resonant cavity with astigmatism. This geometry offered more efficient pump absorption by the YLF:10%Yb laser-cooling crystal compared to non-resonant cavities without astigmatism that have been pursued experimentally so far. Ray tracing simulations indicate that ~80% of the incident pump light can absorbed for temperatures down to ~100 K. Calculations of heat loads, cooling power, and net payload heat lift are presented. They show that it is possible to cool a payload to a range of 90-100 K while producing a net payload heat lift of 80 mW and 300 mW when pumping a YLF:10%Yb crystal with 20 W and 50 W at 1020 nm, respectively. This performance is suited to cool HgCdTe infrared detectors that are used for sensing in the 8-12 μm atmospheric window. While the detector noise would be ~6× greater at 100 K than at 77 K, the laser refrigerator would introduce no vibrations and thus eliminate sources of microphonic noise that are limiting the performance of current systems.

  18. Tunable ultrasonic phononic crystal controlled by infrared radiation

    SciTech Connect

    Walker, Ezekiel; Neogi, Arup E-mail: arup@unt.edu; Reyes, Delfino; Rojas, Miguel Mayorga; Krokhin, Arkadii; Wang, Zhiming E-mail: arup@unt.edu

    2014-10-06

    A tunable phononic crystal based ultrasonic filter was designed by stimulating the phase of the polymeric material embedded in a periodic structure using infrared radiation. The acoustic filter can be tuned remotely using thermal stimulation induced by the infrared radiation. The filter is composed of steel cylinder scatterers arranged periodically in a background of bulk poly (N-isopropylacrylamide) polymer hydrogel. The lattice structure creates forbidden bands for certain sets of mechanical waves that cause it to behave as an ultrasonic filter. Since the bandstructure is determined by not only the arrangement of the scatterers but also the physical properties of the materials composing the scatterers and background, modulating either the arrangement or physical properties will alter the effect of the crystal on propagating mechanical waves. Here, the physical properties of the filter are varied by inducing changes in the polymer hydrogel using an electromagnetic thermal stimulus. With particular focus on the k{sub 00}-wave, the transmission of ultrasonic wave changes by as much as 20 dBm, and band widths by 22% for select bands.

  19. Terahertz-to-infrared emission through laser excitation of surface plasmons in metal films with porous nanostructures.

    PubMed

    Zhang, Liangliang; Zhao, Ji; Wu, Tong; Zhang, Cunlin; Zhang, X-C

    2015-06-29

    We report on the investigation of terahertz-to-infrared (THz-to-IR) thermal emission that relies on the excitation of surface plasmons in metal films deposited on a substrate with randomly ordered nanoscale pore arrays. The THz-to-IR radiation was observed both in the direction of laser beam propagation and the reverse direction. The intensity ratio between backward and forward radiation is exponentially dependent on the nominal thickness of the porous metal films. The findings are discussed in view of the proposed generation mechanism based on propagating surface plasmon polaritons on both air/metal and metal/substrate interfaces. PMID:26191727

  20. Visible-infrared self-amplified spontaneous emission amplifier free electron laser undulator

    NASA Astrophysics Data System (ADS)

    Carr, Roger; Cornacchia, Max; Emma, Paul; Nuhn, Heinz-Dieter; Poling, Ben; Ruland, Robert; Johnson, Erik; Rakowsky, George; Skaritka, John; Lidia, Steve; Duffy, Pat; Libkind, Marcus; Frigola, Pedro; Murokh, Alex; Pellegrini, Claudio; Rosenzweig, James; Tremaine, Aaron

    2001-12-01

    The visible-infrared self-amplified spontaneous emission amplifier (VISA) free electron laser (FEL) is an experimental device designed to show self-amplified spontaneous emission (SASE) to saturation in the near infrared to visible light energy range. It generates a resonant wavelength output from 800-600 nm, so that silicon detectors may be used to characterize the optical properties of the FEL radiation. VISA is designed to show how SASE FEL theory corresponds with experiment in this wavelength range, using an electron beam with emittance close to that planned for the future Linear Coherent Light Source at SLAC. VISA comprises a 4 m pure permanent magnet undulator with four 99 cm segments, each of 55 periods, 18 mm long. The undulator has distributed focusing built into it, to reduce the average beta function of the 70-85 MeV electron beam to about 30 cm. There are four FODO cells per segment. The permanent magnet focusing lattice consists of blocks mounted on either side of the electron beam, in the undulator gap. The most important undulator error parameter for a free electron laser is the trajectory walk-off, or lack of overlap of the photon and electron beams. Using pulsed wire magnet measurements and magnet shimming, we were able to control trajectory walk-off to less than +/-50 μm per field gain length.

  1. Laser-induced reactions in a deep UV resist system: Studied with picosecond infrared spectroscopy

    SciTech Connect

    Lippert, T.; Koskelo, A.; Stoutland, P.O.

    1995-12-31

    One of the most technologically important uses of organic photochemistry is in the imaging industry where radiation-sensitive organic monomers and polymers are used in photoresists. A widely-used class of compounds for imaging applications are diazoketones; these compounds undergo a photoinduced Wolff rearrangement to form a ketene intermediate which subsequently hydrolyses to a base-soluble, carboxylic acid. Another use of organic molecules in polymer matrices is for dopant induced ablation of polymers. As part of a program to develop diagnostics for laser driven reactions in polymer matrices, we have investigated the photoinduced decomposition of 5-diazo-2,2-dimethyl-1,3-dioxane-4,6-dione (5-diazo Meldrum`s acid, DM) in a PMMA matrix using picosecond infrared spectroscopy. In particular, irradiation of DM with a 60 ps 266 nm laser pulse results in immediate bleaching of the diazo infrared band ({nu} = 2172 cm{sup -1}). Similarly, a new band appears within our instrument response at 2161 cm{sup -1} (FWHM = 29 cm{sup -1}) and is stable to greater than 6 ns.; we assign this band to the ketene photoproduct of the Wolff rearrangement. Using deconvolution techniques we estimate a limit for its rate of formation of {tau} < 20 ps. The linear dependence of the absorbance change with the pump power (266 nm) even above the threshold of ablation suggest that material ejection take place after 6ns.

  2. Laser plasma influence on the space-time structure of powerful laser radiation

    NASA Astrophysics Data System (ADS)

    Ananyin, O. B.; Bogdanov, G. S.; Vovchenko, E. D.; Gerasimov, I. A.; Kuznetsov, A. P.; Melekhov, A. P.

    2016-01-01

    This paper deals with the influence of laser plasma on the structure of the radiation field of a powerful Nd-glass laser with pulse energy up to 30 J and with the diameter of the output beam 45 mm. Laser plasma is generated by focusing the laser radiation on a low-density target such as nylon mesh and teflon or mylar films. Temporal profile of the laser pulse with a total duration of 25 ns consists of a several short pulse train. Duration of each pulse is about 2 ns. Notable smoothing of spatially non-uniform radiation structure was observed in the middle of the laser pulse.

  3. Development of a scanning near-field infrared microscope based on a free electron laser

    SciTech Connect

    Hong, M.K.; Erramilli, S.; Jeung, A.

    1995-12-31

    Infrared spectroscopy is one of the most sensitive technique available for identifying and characterizing organic materials. Most molecules exhibit a large number of well-resolved strongly absorbing spectral lines in the mid-IR region of the spectrum. In addition to our own efforts described last year, Creuzet et al have also been working on combining infrared spectroscopy with sub-micron spatial resolution imaging. Scanning Near Field Infrared Microscopy (SNIM) when combined with high brightness tunable FEL radiation, provides a powerful new research tool. We have developed two new probes for use in SNIM. The first are chalcogenide fibers capable of transmitting images in the 2-12 {mu} range. At the Stanford picosecond Free Electron Laser, we have successfully obtained images of metal surfaces and of collagen fibers on diamond at a wavelength of 5.01 {mu}, with a nominal spatial resolution of 0.5 {mu} demonstrating that near field imaging can be obtained on biological samples. At a wavelength of 6.3{mu}, we found that the chalcogenide fibers are limited in their ability to withstand high powers, most likely because of the presence of absorption bands in the polyimide coating used to sheath the brittle fibers. In collaboration with Prof J. Harrington (Rutgers University), we have also developed hollow glass capillaries with metal coated on the inside. These probes are able to withstand significantly higher powers, and can function to longer wavelengths, out into the Far IR region.

  4. 3D Finite Element Model for Writing Long-Period Fiber Gratings by CO2 Laser Radiation

    PubMed Central

    Coelho, João M. P.; Nespereira, Marta; Abreu, Manuel; Rebordão, José

    2013-01-01

    In the last years, mid-infrared radiation emitted by CO2 lasers has become increasing popular as a tool in the development of long-period fiber gratings. However, although the development and characterization of the resulting sensing devices have progressed quickly, further research is still necessary to consolidate functional models, especially regarding the interaction between laser radiation and the fiber's material. In this paper, a 3D finite element model is presented to simulate the interaction between laser radiation and an optical fiber and to determine the resulting refractive index change. Dependence with temperature of the main parameters of the optical fiber materials (with special focus on the absorption of incident laser radiation) is considered, as well as convection and radiation losses. Thermal and residual stress analyses are made for a standard single mode fiber, and experimental results are presented. PMID:23941908

  5. Radiation-Reaction Trapping of Electrons in Extreme Laser Fields

    NASA Astrophysics Data System (ADS)

    Ji, L. L.; Pukhov, A.; Kostyukov, I. Yu.; Shen, B. F.; Akli, K.

    2014-04-01

    A radiation-reaction trapping (RRT) of electrons is revealed in the near-QED regime of laser-plasma interaction. Electrons quivering in laser pulse experience radiation reaction (RR) recoil force by radiating photons. When the laser field reaches the threshold, the RR force becomes significant enough to compensate for the expelling laser ponderomotive force. Then electrons are trapped inside the laser pulse instead of being scattered off transversely and form a dense plasma bunch. The mechanism is demonstrated both by full three-dimensional particle-in-cell simulations using the QED photonic approach and numerical test-particle modeling based on the classical Landau-Lifshitz formula of RR force. Furthermore, the proposed analysis shows that the threshold of laser field amplitude for RRT is approximately the cubic root of laser wavelength over classical electron radius. Because of the pinching effect of the trapped electron bunch, the required laser intensity for RRT can be further reduced.

  6. The role of radiation transport in the thermal response of semitransparent materials to localized laser heating

    SciTech Connect

    Colvin, Jeffrey; Shestakov, Aleksei; Stolken, James; Vignes, Ryan

    2011-03-09

    Lasers are widely used to modify the internal structure of semitransparent materials for a wide variety of applications, including waveguide fabrication and laser glass damage healing. The gray diffusion approximation used in past models to describe radiation cooling is not adequate for these materials, particularly near the heated surface layer. In this paper we describe a computational model based upon solving the radiation transport equation in 1D by the Pn method with ~500 photon energy bands, and by multi-group radiationdiffusion in 2D with fourteen photon energy bands. The model accounts for the temperature-dependent absorption of infrared laser light and subsequent redistribution of the deposited heat by both radiation and conductive transport. We present representative results for fused silica irradiated with 2–12 W of 4.6 or 10.6 µm laser light for 5–10 s pulse durations in a 1 mm spot, which is small compared to the diameter and thickness of the silica slab. Furthermore, we show that, unlike the case for bulk heating, in localized infrared laser heatingradiation transport plays only a very small role in the thermal response of silica.

  7. Influence of low-power laser radiation on the activity of some membraneous and mitochondrial enzymes of hepatocytes in rats

    NASA Astrophysics Data System (ADS)

    Cieslar, Grzegorz; Adamek, Mariusz; Sieron, Aleksander; Kaminski, Marcin

    1995-01-01

    It was observed in some experiments that visible laser radiation activates the enzymatic function of mitochondria, while infrared laser radiation affects the enzymatic activity of cellular membranes. The aim of the study was to estimate the activity of some membranous as well as mitochondrial enzymes of hepatocytes in rats irradiated with infrared laser. Experimental material consisted of 38 Wistar rats divided into 2 groups -- a studied group exposed to infrared laser radiation and a control group, in which no irradiation was made. A semiconductive infrared laser (wavelength -- 904 nm, mean power -- 8.9 mW) was used. The clean-shaven skin of the right infracostal region of animals was irradiated 5 minutes daily for 15 consecutive days. After finishing the experiment in the preparations from obtained segments of the left liver lobe, the enzymatic activity of succinate dehydrogenase (SDH, EC 1.3.99.1), lactic dehydrogenase (LDH, EC 1.1.1.27), Mg2+ dependent ATP-ase (ATP-ase Mg2+, EC 3.1.3.2.) and acid phosphatase (AcP, EC 3.6.1.8.) was estimated with the use of histochemical methods. In the case of SDH and LDH the increase of enzymatic activity was observed in all 3 zones of liver cluster, especially in male rats. In the case of ATP-ase Mg2+ and AcP the increase of enzymatic activity in biliary canaliculi of hepatocytes in all zones of the liver cluster was observed. On the basis of the obtained results it was proved that infrared laser radiation activates significantly the enzymatic activity of most of the analyzed enzymes, which means that it affects not only properties of biological membranes but also activates the oxidoreductive processes of organism, as it has been observed for visible laser radiation. On the basis of the spectrum of energetic levels in macromolecules (Jablonski's diagram) the mechanisms of availed results are discussed both for enzymes possessing and not possessing chromatophores.

  8. Intense Nanosecond-Pulsed Cavity-Dumped Laser Radiation at 1.04 THz

    NASA Astrophysics Data System (ADS)

    Wilson, Thomas

    2013-03-01

    We report first results of intense far-infrared (FIR) nanosecond-pulsed laser radiation at 1.04 THz from a previously described[2] cavity-dumped, optically-pumped molecular gas laser. The gain medium, methyl fluoride, is pumped by the 9R20 line of a TEA CO2 laser[3] with a pulse energy of 200 mJ. The THz laser pulses contain of 30 kW peak power in 5 nanosecond pulse widths at a pulse repetition rate of 10 Hz. The line width, measured by a scanning metal-mesh FIR Fabry-Perot interferometer, is 100 MHz. The novel THz laser is being used in experiments to resonantly excite coherent ns-pulsed 1.04 THz longitudinal acoustic phonons in silicon doping-superlattices. The research is supported by NASA EPSCoR NNX11AM04A and AFOSR FA9550-12-1-0100 awards.

  9. Generation of widely tunable intense far-infrared radiation pulses by stimulated Raman transitions in methylfluoride gas

    SciTech Connect

    Lang, P.T.; Sessler, F.; Werling, U.; Renk, K.F. )

    1989-12-18

    We report on the generation of widely tunable intense far-infrared radiation pulses by stimulated Raman transitions in methylfluoride gas. Using a tunable high-pressure CO{sub 2} laser we achieved, by {ital P}-branch tuning of stimulated Raman transitions in {sup 12}CH{sub 3}F and {sup 13}CH{sub 3}F gases, tunable generation of radiation in a series of intervals in the spectral range from 37 to 72 cm{sup {minus}1} covering 20% of this range. Possibilities of further extension of the tuning regions are also discussed.

  10. Mid-infrared photothermal heterodyne spectroscopy in a liquid crystal using a quantum cascade laser

    PubMed Central

    Mërtiri, Alket; Jeys, Thomas; Liberman, Vladimir; Hong, M. K.; Mertz, Jerome; Altug, Hatice; Erramilli, Shyamsunder

    2012-01-01

    We report a technique to measure the mid-infrared photothermal response induced by a tunable quantum cascade laser in the neat liquid crystal 4-octyl-4′-cyanobiphenyl (8CB), without any intercalated dye. Heterodyne detection using a Ti:sapphire laser of the response in the solid, smectic, nematic and isotropic liquid crystal phases allows direct detection of a weak mid-infrared normal mode absorption using an inexpensive photodetector. At high pump power in the nematic phase, we observe an interesting peak splitting in the photothermal response. Tunable lasers that can access still stronger modes will facilitate photothermal heterodyne mid-infrared vibrational spectroscopy. PMID:22912508

  11. 3D Thermal Infrared Radiative Transfer in Mountains

    NASA Astrophysics Data System (ADS)

    Lee, W.; Liou, K.; Hall, A.

    2007-12-01

    We developed a 3D Monte Carlo photon tracing program for radiative transfer in inhomogeneous and irregular terrain coupled with the correlated k-distribution method for gaseous absorption in the atmosphere for the calculation of broadband thermal infrared (IR) fluxes at mountain surfaces. The thermal IR radiative transfer program includes emission from the atmosphere to the surface and vice versa as well as emissions between mountain surfaces. Both the atmosphere and the land surface are discretized by using finite cubic cells characterized by the spectral optical properties of molecules and background aerosols (absorption coefficient, single-scattering albedo, and scattering phase function) and terrain configuration (albedo, elevation, slope, and orientation). The emissivity of gases is parameterized in terms of the vertical optical depth of cubic cell. We selected an area of 100×100 km2 in the Tibetan Plateau near Lhasa city with a horizontal resolution of 1 km2 and used the surface temperature and albedo available from MODIS/Terra dataset for this study. We show that surface temperature is the dominating factor in radiative transfer calculations and that subgrid variability of the net surface IR flux distribution relative to a flat surface (1D) with average elevation and temperature can be as large as 50 W/m2 at cold mountain surfaces.

  12. Broadband near-field infrared spectromicroscopy using photothermal probes and synchrotron radiation.

    PubMed

    Donaldson, Paul M; Kelley, Chris S; Frogley, Mark D; Filik, Jacob; Wehbe, Katia; Cinque, Gianfelice

    2016-02-01

    In this paper, we experimentally demonstrate the use of infrared synchrotron radiation (IR-SR) as a broadband source for photothermal near-field infrared spectroscopy. We assess two methods of signal transduction; cantilever resonant thermal expansion and scanning thermal microscopy. By means of rapid mechanical chopping (50-150 kHz), we modulate the IR-SR at rates matching the contact resonance frequencies of atomic force microscope (AFM) cantilevers, allowing us to record interferograms yielding Fourier transform infrared (FT-IR) photothermal absorption spectra of polystyrene and cyanoacrylate films. Complementary offline measurements using a mechanically chopped CW IR laser confirmed that the resonant thermal expansion IR-SR measurements were below the diffraction limit, with a spatial resolution better than 500 nm achieved at a wavelength of 6 μm, i.e. λ/12 for the samples studied. Despite achieving the highest signal to noise so far for a scanning thermal microscopy measurement under conditions approaching near-field (dictated by thermal diffusion), the IR-SR resonant photothermal expansion FT-IR spectra measured were significantly higher in signal to noise in comparison with the scanning thermal data. PMID:26906764

  13. Fast Infrared Chemical Imaging with a Quantum Cascade Laser

    PubMed Central

    2015-01-01

    Infrared (IR) spectroscopic imaging systems are a powerful tool for visualizing molecular microstructure of a sample without the need for dyes or stains. Table-top Fourier transform infrared (FT-IR) imaging spectrometers, the current established technology, can record broadband spectral data efficiently but requires scanning the entire spectrum with a low throughput source. The advent of high-intensity, broadly tunable quantum cascade lasers (QCL) has now accelerated IR imaging but results in a fundamentally different type of instrument and approach, namely, discrete frequency IR (DF-IR) spectral imaging. While the higher intensity of the source provides a higher signal per channel, the absence of spectral multiplexing also provides new opportunities and challenges. Here, we couple a rapidly tunable QCL with a high performance microscope equipped with a cooled focal plane array (FPA) detector. Our optical system is conceptualized to provide optimal performance based on recent theory and design rules for high-definition (HD) IR imaging. Multiple QCL units are multiplexed together to provide spectral coverage across the fingerprint region (776.9 to 1904.4 cm–1) in our DF-IR microscope capable of broad spectral coverage, wide-field detection, and diffraction-limited spectral imaging. We demonstrate that the spectral and spatial fidelity of this system is at least as good as the best FT-IR imaging systems. Our configuration provides a speedup for equivalent spectral signal-to-noise ratio (SNR) compared to the best spectral quality from a high-performance linear array system that has 10-fold larger pixels. Compared to the fastest available HD FT-IR imaging system, we demonstrate scanning of large tissue microarrays (TMA) in 3-orders of magnitude smaller time per essential spectral frequency. These advances offer new opportunities for high throughput IR chemical imaging, especially for the measurement of cells and tissues. PMID:25474546

  14. Ultrastructural study of thyroid capillaries after IR laser radiation

    NASA Astrophysics Data System (ADS)

    Vidal, Lourdes; Perez de Vargas, I.; Carrillo, F.; Parrado, C.; Pelaez, A.

    1994-02-01

    Laser radiation causes microscopical changes in the follicular cells relative to dose intensity. So, we have observed focal degenerative phenomena, at maximal doses, and activation of cellular function similar to the ones observed after stimulation with TSH, at minimal doses. In order to evaluate the evolution of these changes we have planned an ultrastructural study of rats thyroid capillaries treated with IR laser radiation.

  15. Characterization of the backscattered radiation from petawatt laser matter interactions

    SciTech Connect

    Vernon, Edwina D.; Musgrave, Ian O.; Green, James; Heathcote, Robert; Lancaster, Kate L.; Mendes, Cedric; Hawkes, Steve J.; Hernandez-Gomez, Cristina; Pepler, Dave A

    2008-06-20

    The development of high peak power and energy laser systems require the assurance that any backscattered radiation will not lead to damage of the laser system. We present the characterization of the backscattered radiation for different target types and conditions at petawatt power levels and intensities (>10{sup 20}W/cm{sup 2}). We observe that radiation is generated between 700 and 900 nm, as well as the expected self emission and laser fundamental. The percentage of the incident light backscattered reduces as a function of the incident energy and is typically <1% for petawatt laser interactions.

  16. Intensity clamping in the filament of femtosecond laser radiation

    SciTech Connect

    Kandidov, V P; Fedorov, V Yu; Tverskoi, O V; Kosareva, O G; Chin, S L

    2011-04-30

    We have studied numerically the evolution of the light field intensity and induced refractive index of a medium upon filamentation of femtosecond laser radiation in air. It is shown that the intensity clamping results from the dynamic balance of optical powers of nonlinear lenses, induced by radiation due to the Kerr nonlinearity of air, and laser plasma produced during photoionisation. We have found the relation between the peak values of the light field intensity and the electron density in laser-produced plasma, as well as the transverse sizes of the filament and the plasma channel. (effects of laser radiation on matter)

  17. Diffraction Properties of Periodic Lattices under Free Electron Laser Radiation

    SciTech Connect

    Rajkovic, I.; Busse, G.; Hallmann, J.; More, R.; Petri, M.; Quevedo, W.; Krasniqi, F.; Rudenko, A.; Tschentscher, T.; Stojanovic, N.; Duesterer, S.; Treusch, R.; Tolkiehn, M.; Techert, S.

    2010-03-26

    In this Letter, we report the pioneering use of free electron laser radiation for the investigation of periodic crystalline structures. The diffraction properties of silver behenate single nanocrystals (5.8 nm periodicity) with the dimensions of 20 nmx20 nmx20 {mu}m and as powder with grain sizes smaller than 200 nm were investigated with 8 nm free electron laser radiation in single-shot modus with 30 fs long free electron laser pulses. This work emphasizes the possibility of using soft x-ray free electron laser radiation for these crystallographic studies on a nanometer scale.

  18. Photoablation of polyimide with IR and UV laser radiation

    NASA Astrophysics Data System (ADS)

    Braun, R.; Nowak, R.; Hess, P.; Oetzmann, H.; Schmidt, C.

    1989-12-01

    IR and UV ablation experiments were performed for freestanding polyimide foils (75 μm) and spincoated films of polyimide (6-7 μm). Compared to results reported in the literature a considerably improved etch quality was obtained with a pulsed TEA CO2 laser. Distinct interference effects were found for KrF laser radiation and CO2 laser radiation. The fluence dependence of the etch rates was studied for excimer laser light at 248 nm and IR laser light at 1082.3, 1057.3 and 970.5 cm-1. The optical absorption coefficient was determined by reflectivity and transmittance measurements.

  19. Nonlinear femtosecond near infrared laser structuring in oxide glasses

    NASA Astrophysics Data System (ADS)

    Royon, Arnaud

    Three-dimensional femtosecond laser structuring has a growing interest because of its ease of implementation and the numerous possible applications in the domain of photonic components. Structures such as waveguides, diffraction gratings, optical memories or photonic crystals can be fabricated thanks to this technique. Its use with oxide glasses is promising because of several advantages; they are resistant to flux and ageing, their chemical composition can easily be changed to fit the well-defined requirements of an application. They can already be found in Raman amplifiers, optical fibers, fiber lasers, and other devices. This thesis is based on two axes. The first axis consists in characterizing the linear and nonlinear optical properties of bulk vitreous materials in order to optimize their composition with a particular application in view. Within this context, the nonlinear optical properties, their physical origins (electronic and nuclear) as well as their characteristic response times (from a few femtoseconds to a few hundreds of picoseconds) are described within the Born-Oppenheimer approximation. Fused silica and several sodium-borophosphate glasses containing different concentrations in niobium oxide have been studied. Results show that the nonlinear optical properties of fused silica are mainly from electronic origin, whereas in the sodium-borophosphate glasses, the contribution from nuclear origin becomes predominant when the concentration of niobium oxide exceeds 30%. The second axis is based on the structuring of materials. Three commercially available fused silica samples presenting different fabrication conditions (therefore distinct impurity levels) and irradiated with a near infrared femtosecond laser have been studied. The laser induced defects have been identified by means of several spectroscopic techniques. They show the formation of color centers as well as a densification inside the irradiated area. Their linear refractive index and

  20. Far Infrared Spectrometry of the Cosmic Background Radiation

    DOE R&D Accomplishments Database

    Mather, J. C.

    1974-01-01

    I describe two experiments to measure the cosmic background radiation near 1 mm wavelength. The first was a ground-based search for spectral lines, made with a Fabry-Perot interferometer and an InSb detector. The second is a measurement of the spectrum from 3 to 18 cm{sup -1}, made with a balloon-borne Fourier transform spectrometer. It is a polarizing Michelson interferometer, cooled in liquid helium, and operated with a germanium bolometer. I give the theory of operation, construction details, and experimental results. The first experiment was successfully completed but the second suffered equipment malfunction on its first flight. I describe the theory of Fourier transformations and give a new understanding of convolutional phase correction computations. I discuss for infrared bolometer calibration procedures, and tabulate test results on nine detectors. I describe methods of improving bolometer sensitivity with immersion optics and with conductive film blackening.

  1. An infrared radiation based thermal biosensor for enzymatic biochemical reactions.

    PubMed

    Zhang, Lei; Dong, Tao; Zhao, Xinyan; Yang, Zhaochu; Pires, Nuno M M

    2012-01-01

    In this paper, a thermal biosensor based on the infrared radiation energy is proposed for calorimetric measurement of biochemical reactions. Having a good structure design combined with MEMS technology as well as employing the Si /SiGe quantum well sensing material with a high TCR and low 1/f noise, the sensor shows potentials to be high sensitive and real-time. The urea enzymatic reaction was tested to verify the performance of sensor, which demonstrates a linear detection range from 0.5mM to 150mM and a relative standard deviation less than 1%. For the sensor fabrication, wafer-level transfer bonding is a key process, which makes the integration of quantum well material and a free standing structure possible. It reduces the heat loss from the sensor to the surrounding environment. PMID:23365944

  2. Effects of flameless catalytic infrared radiation on Sitophilus oryzae (L.) life stages

    Technology Transfer Automated Retrieval System (TEKTRAN)

    A laboratory bench top flameless catalytic infrared emitter was evaluated against all life stages of the rice weevil, Sitophilus oryzae (L.), an insect species associated with stored wheat. The infrared radiation emitted was in the 3 to 7 µm range. A non-contact infrared thermometer measured grain t...

  3. Studies on suppression methodology of internal radiation for satellite-borne infrared camera

    NASA Astrophysics Data System (ADS)

    Peng, Honggang; Jin, Libing; Liu, Jianfeng; Zhou, Feng

    2015-08-01

    Infrared camera, which works on cryogenic or normal temperature, has thermal radiation inside. It is called interior radiation. In the space optical remote sensor, interior radiation will produce a lot of bad effects. Firstly, it can depress image contrast. What is more, dynamic range and integral time will be decreased. Lastly, interior radiation is one of the main factors that affect the measurement accuracy. So, restraining interior radiation is one of the key technologies to enhance the quality of infrared thermal imaging technology. In this paper, the typical technology of restraining interior radiation is summarized. At the end of the paper, blue prints for restraining interior radiation are proposed.

  4. Algorithmic vs. finite difference Jacobians for infrared atmospheric radiative transfer

    NASA Astrophysics Data System (ADS)

    Schreier, Franz; Gimeno García, Sebastián; Vasquez, Mayte; Xu, Jian

    2015-10-01

    Jacobians, i.e. partial derivatives of the radiance and transmission spectrum with respect to the atmospheric state parameters to be retrieved from remote sensing observations, are important for the iterative solution of the nonlinear inverse problem. Finite difference Jacobians are easy to implement, but computationally expensive and possibly of dubious quality; on the other hand, analytical Jacobians are accurate and efficient, but the implementation can be quite demanding. GARLIC, our "Generic Atmospheric Radiation Line-by-line Infrared Code", utilizes algorithmic differentiation (AD) techniques to implement derivatives w.r.t. atmospheric temperature and molecular concentrations. In this paper, we describe our approach for differentiation of the high resolution infrared and microwave spectra and provide an in-depth assessment of finite difference approximations using "exact" AD Jacobians as a reference. The results indicate that the "standard" two-point finite differences with 1 K and 1% perturbation for temperature and volume mixing ratio, respectively, can exhibit substantial errors, and central differences are significantly better. However, these deviations do not transfer into the truncated singular value decomposition solution of a least squares problem. Nevertheless, AD Jacobians are clearly recommended because of the superior speed and accuracy.

  5. Secure thermal infrared communications using engineered blackbody radiation

    PubMed Central

    Liang, Xiaoxin; Hu, Fangjing; Yan, Yuepeng; Lucyszyn, Stepan

    2014-01-01

    The thermal (emitted) infrared frequency bands, from 20–40 THz and 60–100 THz, are best known for applications in thermography. This underused and unregulated part of the spectral range offers opportunities for the development of secure communications. The ‘THz Torch' concept was recently presented by the authors. This technology fundamentally exploits engineered blackbody radiation, by partitioning thermally-generated spectral noise power into pre-defined frequency channels; the energy in each channel is then independently pulsed modulated and multiplexing schemes are introduced to create a robust form of short-range secure communications in the far/mid infrared. To date, octave bandwidth (25–50 THz) single-channel links have been demonstrated with 380 bps speeds. Multi-channel ‘THz Torch' frequency division multiplexing (FDM) and frequency-hopping spread-spectrum (FHSS) schemes have been proposed, but only a slow 40 bps FDM scheme has been demonstrated experimentally. Here, we report a much faster 1,280 bps FDM implementation. In addition, an experimental proof-of-concept FHSS scheme is demonstrated for the first time, having a 320 bps data rate. With both 4-channel multiplexing schemes, measured bit error rates (BERs) of < 10−6 are achieved over a distance of 2.5 cm. Our approach represents a new paradigm in the way niche secure communications can be established over short links. PMID:24912871

  6. Secure thermal infrared communications using engineered blackbody radiation

    NASA Astrophysics Data System (ADS)

    Liang, Xiaoxin; Hu, Fangjing; Yan, Yuepeng; Lucyszyn, Stepan

    2014-06-01

    The thermal (emitted) infrared frequency bands, from 20-40 THz and 60-100 THz, are best known for applications in thermography. This underused and unregulated part of the spectral range offers opportunities for the development of secure communications. The `THz Torch' concept was recently presented by the authors. This technology fundamentally exploits engineered blackbody radiation, by partitioning thermally-generated spectral noise power into pre-defined frequency channels; the energy in each channel is then independently pulsed modulated and multiplexing schemes are introduced to create a robust form of short-range secure communications in the far/mid infrared. To date, octave bandwidth (25-50 THz) single-channel links have been demonstrated with 380 bps speeds. Multi-channel `THz Torch' frequency division multiplexing (FDM) and frequency-hopping spread-spectrum (FHSS) schemes have been proposed, but only a slow 40 bps FDM scheme has been demonstrated experimentally. Here, we report a much faster 1,280 bps FDM implementation. In addition, an experimental proof-of-concept FHSS scheme is demonstrated for the first time, having a 320 bps data rate. With both 4-channel multiplexing schemes, measured bit error rates (BERs) of < 10-6 are achieved over a distance of 2.5 cm. Our approach represents a new paradigm in the way niche secure communications can be established over short links.

  7. Secure thermal infrared communications using engineered blackbody radiation.

    PubMed

    Liang, Xiaoxin; Hu, Fangjing; Yan, Yuepeng; Lucyszyn, Stepan

    2014-01-01

    The thermal (emitted) infrared frequency bands, from 20-40 THz and 60-100 THz, are best known for applications in thermography. This underused and unregulated part of the spectral range offers opportunities for the development of secure communications. The 'THz Torch' concept was recently presented by the authors. This technology fundamentally exploits engineered blackbody radiation, by partitioning thermally-generated spectral noise power into pre-defined frequency channels; the energy in each channel is then independently pulsed modulated and multiplexing schemes are introduced to create a robust form of short-range secure communications in the far/mid infrared. To date, octave bandwidth (25-50 THz) single-channel links have been demonstrated with 380 bps speeds. Multi-channel 'THz Torch' frequency division multiplexing (FDM) and frequency-hopping spread-spectrum (FHSS) schemes have been proposed, but only a slow 40 bps FDM scheme has been demonstrated experimentally. Here, we report a much faster 1,280 bps FDM implementation. In addition, an experimental proof-of-concept FHSS scheme is demonstrated for the first time, having a 320 bps data rate. With both 4-channel multiplexing schemes, measured bit error rates (BERs) of < 10(-6) are achieved over a distance of 2.5 cm. Our approach represents a new paradigm in the way niche secure communications can be established over short links. PMID:24912871

  8. Laser radiation attenuation by sparks of optical breakdown

    NASA Astrophysics Data System (ADS)

    Budnik, A. P.; Semenov, L. P.; Skripkin, A. M.; Volkovitskii, O. A.

    1989-06-01

    A breakdown generated by laser radiation in a gas contaminated by aerosol particles is known to occur at much lower radiation intensities than in case of pure gases. Laser radiation is heavily attenuated by sparks of plasma formed at breakdowns. Energy loss estimation is important at radiation propagation in the atmosphere and in laser resonators. The breakdown phenomenon may be used in diagnostics of the atmospheric aerosol contamination events. The report presents experimental data on the influence of aerosol size distribution and concentration on optical breakdown generation and other results.

  9. Laser Radiation Attenuation By Sparks Of Optical Breakdown

    NASA Astrophysics Data System (ADS)

    Budnik, A. P.; Semenov, L. P.; Skripkin, A. M.; Volkovitsky, O. A.

    1990-01-01

    A breakdown generated by laser radiation in a gas contaminated by aerosol particles is known to occur at much lower radiation intensities than in case of pure gases, Laser radiation is heavily attenuated by sparks of plasma formed at breakdowns. Energy loss estimation is important at radiation propagation in the atmosphere and in laser resonators. The breakdown phenomenon may be used in diagnostics of the atmospheric aerosol contamination events. The report presents experimental data on the influence of aerosol size distribution and concentration on optical breakdown generation and other results.

  10. A review of infrared laser energy absorption and subsequent healing in the cornea

    NASA Astrophysics Data System (ADS)

    Saunders, Latica L.; Johnson, Thomas E.; Neal, Thomas A.

    2004-07-01

    The purpose of this review is to compile information on the optical and healing properties of the cornea when exposed to infrared lasers. Our long-term goal is to optimize the treatment parameters for corneal injuries after exposure to infrared laser systems. The majority of the information currently available in the literature focuses on corneal healing after therapeutic vision correction surgery with LASIK or PRK. Only a limited amount of information is available on corneal healing after injury with an infrared laser system. In this review we will speculate on infrared photon energy absorption in corneal injury and healing to include the role of the tear layer. The aim of this review is to gain a better understanding of infrared energy absorption in the cornea and how it might impact healing.

  11. Fiber laser pumped high power mid-infrared laser with picosecond pulse bunch output.

    PubMed

    Wei, Kaihua; Chen, Tao; Jiang, Peipei; Yang, Dingzhong; Wu, Bo; Shen, Yonghang

    2013-10-21

    We report a novel quasi-synchronously pumped PPMgLN-based high power mid-infrared (MIR) laser with picosecond pulse bunch output. The pump laser is a linearly polarized MOPA structured all fiberized Yb fiber laser with picosecond pulse bunch output. The output from a mode-locked seed fiber laser was directed to pass through a FBG reflector via a circulator to narrow the pulse duration from 800 ps to less than 50 ps and the spectral FWHM from 9 nm to 0.15 nm. The narrowed pulses were further directed to pass through a novel pulse multiplier through which each pulse was made to become a pulse bunch composing of 13 sub-pulses with pulse to pulse time interval of 1.26 ns. The pulses were then amplified via two stage Yb fiber amplifiers to obtain a linearly polarized high average power output up to 85 W, which were then directed to pass through an isolator and to pump a PPMgLN-based optical parametric oscillator via quasi-synchronization pump scheme for ps pulse bunch MIR output. High MIR output with average power up to 4 W was obtained at 3.45 micron showing the feasibility of such pump scheme for ps pulse bunch MIR output. PMID:24150378

  12. Design of an infrared camera based aircraft detection system for laser guide star installations

    SciTech Connect

    Friedman, H.; Macintosh, B.

    1996-03-05

    There have been incidents in which the irradiance resulting from laser guide stars have temporarily blinded pilots or passengers of aircraft. An aircraft detection system based on passive near infrared cameras (instead of active radar) is described in this report.

  13. The correction model and error analysis of infrared radiation temperature measurement of semitransparent object

    NASA Astrophysics Data System (ADS)

    Zhao, Xiaolong; Yang, Li

    2015-10-01

    Based on the theory of infrared radiation and of the infrared thermography, the mathematical correction model of the infrared radiation temperature measurement of semitransparent object is developed taking account by the effects of the atmosphere, surroundings, radiation of transmissivity and many other factors. The effects of the emissivity, transmissivity and measurement error are analysed on temperature measurement error of the infrared thermography. The measurement error of semitransparent object are compared with that of opaque object. The countermeasures to reduce the measurement error are also discussed.

  14. Single and Multiphoton Infrared Laser Sectroscopy of Atomic Negative Ions

    NASA Astrophysics Data System (ADS)

    Bilodeau, René C.; Scheer, Michael; Brodie, Cicely A.; Haugen, Harold K.

    1998-05-01

    We have investigated several atomic negative ion species with the aid of a pulsed, tunable infrared laser source (M. Scheer, H.K. Haugen, and D.R. Beck, Phys. Rev. Lett. 79), 4104 (1997); M. Scheer et al, Phys. Rev. Lett. 80, 684 (1998).. In a comprehensive study of the carbon group negative ions (C^-, Si^-, Ge^-, Sn^-, Pb^-) a combination of single and multiphoton techniques was utilized to determine the bound terms and fine structure levels of the p^3 (ground state) configuration. The results comprise accurate electron affinities and the first experimental data on the fine structure of the ^2DJ terms in Si^-, Ge^-, and Sn^-. In addition, photodetachment threshold spectroscopy provided significantly impoved electron affinities for B, Cr, Mo, Ru, Rh, W, and Bi. The detachment cross section of B^-(^3P_J) appeared as a sequence of closely spaced thresholds which enabled the first experimental determination of the ionic fine structure. The detachment cross section of W^- indicates the presence of unexpected and previously unobserved resonances just below the W(5d^56s ^7S_3) threshold.

  15. Short infrared (IR) laser pulses can induce nanoporation

    NASA Astrophysics Data System (ADS)

    Roth, Caleb C.; Barnes, Ronald A.; Ibey, Bennett L.; Glickman, Randolph D.; Beier, Hope T.

    2016-03-01

    Short infrared (IR) laser pulses on the order of hundreds of microseconds to single milliseconds with typical wavelengths of 1800-2100 nm, have shown the capability to reversibly stimulate action potentials (AP) in neuronal cells. While the IR stimulation technique has proven successful for several applications, the exact mechanism(s) underlying the AP generation has remained elusive. To better understand how IR pulses cause AP stimulation, we determined the threshold for the formation of nanopores in the plasma membrane. Using a surrogate calcium ion, thallium, which is roughly the same shape and charge, but lacks the biological functionality of calcium, we recorded the flow of thallium ions into an exposed cell in the presence of a battery of channel antagonists. The entry of thallium into the cell indicated that the ions entered via nanopores. The data presented here demonstrate a basic understanding of the fundamental effects of IR stimulation and speculates that nanopores, formed in response to the IR exposure, play an upstream role in the generation of AP.

  16. Comparing the use of mid-infrared versus far-infrared lasers for mitigating damage growth on fused silica

    SciTech Connect

    Yang, Steven T.; Matthews, Manyalibo J.; Elhadj, Selim; Cooke, Diane; Guss, Gabriel M.; Draggoo, Vaughn G.; Wegner, Paul J.

    2010-05-10

    Laser-induced growth of optical damage can limit component lifetime and, therefore, increase operating costs of large-aperture fusion-class laser systems. While far-infrared (IR) lasers have been used previously to treat laser damage on fused silica optics and render it benign, little is known about the effectiveness of less-absorbing mid-IR lasers for this purpose. In this study, we quantitatively compare the effectiveness and efficiency of mid-IR (4.6 {mu}m) versus far-IR (10.6 {mu}m) lasers in mitigating damage growth on fused silica surfaces. The nonlinear volumetric heating due to mid-IR laser absorption is analyzed by solving the heat equation numerically, taking into account the temperature-dependent absorption coefficient {alpha}(T) at {lambda}=4.6 {mu}m, while far-IR laser heating is well described by a linear analytic approximation to the laser-driven temperature rise. In both cases, the predicted results agree well with surface temperature measurements based on IR radiometry, as well as subsurface fictive temperature measurements based on confocal Raman microscopy. Damage mitigation efficiency is assessed using a figure of merit (FOM) relating the crack healing depth to laser power required, under minimally ablative conditions. Based on our FOM, we show that, for cracks up to at least 500 {mu}m in depth, mitigation with a 4.6 {mu}m mid-IR laser is more efficient than mitigation with a 10.6 {mu}m far-IR laser. This conclusion is corroborated by direct application of each laser system to the mitigation of pulsed laser-induced damage possessing fractures up to 225 {mu}m in depth.

  17. Electric field detection of coherent synchrotron radiation in a storage ring generated using laser bunch slicing

    NASA Astrophysics Data System (ADS)

    Katayama, I.; Shimosato, H.; Bito, M.; Furusawa, K.; Adachi, M.; Shimada, M.; Zen, H.; Kimura, S.; Yamamoto, N.; Hosaka, M.; Katoh, M.; Ashida, M.

    2012-03-01

    The electric field of coherent synchrotron radiation (CSR) generated by laser bunch slicing in a storage ring has been detected by an electro-optic sampling method. The gate pulses for sampling are sent through a large-mode-area photonic-crystal fiber. The observed electric field profile of the CSR is in good agreement with the spectrum of the CSR observed using Fourier transform far-infrared spectrometry, indicating good phase stability in the CSR. The longitudinal density profiles of electrons modulated by laser pulses were evaluated from the electric field profile.

  18. Electric field detection of coherent synchrotron radiation in a storage ring generated using laser bunch slicing

    SciTech Connect

    Katayama, I.; Shimosato, H.; Bito, M.; Furusawa, K.; Adachi, M.; Zen, H.; Kimura, S.; Katoh, M.; Shimada, M.; Yamamoto, N.; Hosaka, M.; Ashida, M.

    2012-03-12

    The electric field of coherent synchrotron radiation (CSR) generated by laser bunch slicing in a storage ring has been detected by an electro-optic sampling method. The gate pulses for sampling are sent through a large-mode-area photonic-crystal fiber. The observed electric field profile of the CSR is in good agreement with the spectrum of the CSR observed using Fourier transform far-infrared spectrometry, indicating good phase stability in the CSR. The longitudinal density profiles of electrons modulated by laser pulses were evaluated from the electric field profile.

  19. Resonance transition radiation X-ray laser

    NASA Technical Reports Server (NTRS)

    Reid, Max B.; Piestrup, Melvin A.

    1991-01-01

    A free electron laser is proposed using a periodic dielectric and helical magnetic field. Periodic synchronism between the electrons and the optical wave is obtained at the period of the dielectric and not at the period of the helical magnetic field. The synchronism condition and the gain of the new device are derived. The effects on the gain from dephasing and beam expansion due to elastic scattering of the electrons in the periodic medium are included in the gain calculation. Examples of the resonance transition radiation laser and klystron are given. Operation at photon energies between 2.5 and 3.5 keV with net gain up to 12 percent is feasible using high electron-beam energies of 3 and 5 GeV. Moderate (300-MeV) beam energy allows operation between 80 to 110 eV with up to 57 percent net gain using a klystron design. In both cases, rapid foil heating may limit operation to a single electron-beam pulse.

  20. Development of mid-infrared solid state lasers for spaceborne lidar

    NASA Technical Reports Server (NTRS)

    Whitney, Donald A.; Kim, Kyong H.

    1988-01-01

    This semiannual progress report covers work performed during the period from April 13, 1988 to October 13, 1988 under NASA grant number NAG-1-877 entitled, Development of mid-infrared solid state lasers for spaceborne lidar. We have designed a flashlamp-pumped Cr3(+);GSAG laser of pulsed laser energy greater than 200 mJ and of pulse width of 1 ms FWHM to simulate a high-power laser diode in pumping mid-infrared laser crystals such as Tm3(+), Er3(+), and/or Ho3(+)-ion doped YAG, YLF or other host materials. This Cr3(+);GSAG laser will be used to determine optimum conditions for laser diode pumped mid-infrared lasers, maximum energy extraction limit with longitudinal pumping, thermal damage limit, and other problems related to high power laser diode pumping. We have completed a modification of an existing flashlamp-pumped and liquid nitrogen cooled rare earth laser system for 60 J electrical input energy and a 500 micron pulse width, and have carried out preliminary experiments with a Ho(+):Er3(+):Tm3(+):YAG crystal to test the system performance. This flashlamp-pumped rare earth laser system will be used to determine optimum Tm3(+)-ion concentration in Ho3(+):Cr3(+):Tm3(+):YAG crystal in the remaining research period.

  1. Low intensity infrared laser effects on Escherichia coli cultures and plasmid DNA

    NASA Astrophysics Data System (ADS)

    Fonseca, A. S.; Teixeira, A. F.; Presta, G. A.; Geller, M.; Valença, S. S.; Paoli, F.

    2012-10-01

    Biostimulative effect of low intensity laser in tissues has been described on a photobiological basis and clinical protocols are recommended for treatment of various diseases. The aim of this work was to evaluate effects of laser exposure on the survival of Escherichia coli cultures and plasmid topological forms. Escherichia coli cultures and plasmids were exposed to infrared laser to study bacterial survival and electrophoretic profile, respectively. Data indicate low intensity infrared laser: (i) had no effect on E. coli wild type, endonuclease IV, exonuclease III, formamidopyrimidine DNA glycosylase/MutM protein and endonuclease III deficient cultures, but decreased the survival of E. coli UvrA protein deficient cultures; (ii) there was no alteration in the electrophoretic profile of plasmids. Exposure to low intensity infrared laser decreases survival of Escherichia coli cultures deficient in nucleotide excision repair of DNA and this effect could depend on fluences, wavelength and tissues conditions.

  2. Phase-locked, erbium-fiber-laser-based frequency comb in the near infrared.

    PubMed

    Washburn, Brian R; Diddams, Scott A; Newbury, Nathan R; Nicholson, Jeffrey W; Yan, Man F; Jørgensen, Carsten G

    2004-02-01

    A phase-locked frequency comb in the near infrared is demonstrated with a mode-locked, erbium-doped, fiber laser whose output is amplified and spectrally broadened in dispersion-flattened, highly nonlinear optical fiber to span from 1100 to >2200 nm. The supercontinuum output comprises a frequency comb with a spacing set by the laser repetition rate and an offset by the carrier-envelope offset frequency, which is detected with the standard f-to-2f heterodyne technique. The comb spacing and offset frequency are phase locked to a stable rf signal with a fiber stretcher in the laser cavity and by control of the pump laser power, respectively. This infrared comb permits frequency metrology experiments in the near infrared in a compact, fiber-laser-based system. PMID:14759041

  3. A Thermal Infrared Radiation Parameterization for Atmospheric Studies

    NASA Technical Reports Server (NTRS)

    Chou, Ming-Dah; Suarez, Max J.; Liang, Xin-Zhong; Yan, Michael M.-H.; Cote, Charles (Technical Monitor)

    2001-01-01

    This technical memorandum documents the longwave radiation parameterization developed at the Climate and Radiation Branch, NASA Goddard Space Flight Center, for a wide variety of weather and climate applications. Based on the 1996-version of the Air Force Geophysical Laboratory HITRAN data, the parameterization includes the absorption due to major gaseous absorption (water vapor, CO2, O3) and most of the minor trace gases (N2O, CH4, CFCs), as well as clouds and aerosols. The thermal infrared spectrum is divided into nine bands. To achieve a high degree of accuracy and speed, various approaches of computing the transmission function are applied to different spectral bands and gases. The gaseous transmission function is computed either using the k-distribution method or the table look-up method. To include the effect of scattering due to clouds and aerosols, the optical thickness is scaled by the single-scattering albedo and asymmetry factor. The parameterization can accurately compute fluxes to within 1% of the high spectral-resolution line-by-line calculations. The cooling rate can be accurately computed in the region extending from the surface to the 0.01-hPa level.

  4. Infrared radiative transfer through a regular array of cuboidal clouds

    NASA Technical Reports Server (NTRS)

    HARSHVARDHAN; Weinman, J. A.

    1981-01-01

    Infrared radiative transfer through a regular array of cuboidal clouds is studied and the interaction of the sides of the clouds with each other and the ground is considered. The theory is developed for black clouds and is extended to scattering clouds using a variable azimuth two-stream approximation. It is shown that geometrical considerations often dominate over the microphysical aspects of radiative transfer through the clouds. For example, the difference in simulated 10 micron brightness temperature between black isothermal cubic clouds and cubic clouds of optical depth 10, is less than 2 deg for zenith angles less than 50 deg for all cloud fractions when viewed parallel to the array. The results show that serious errors are made in flux and cooling rate computations if broken clouds are modeled as planiform. Radiances computed by the usual practice of area-weighting cloudy and clear sky radiances are in error by 2 to 8 K in brightness temperature for cubic clouds over a wide range of cloud fractions and zenith angles. It is also shown that the lapse rate does not markedly affect the exiting radiances for cuboidal clouds of unit aspect ratio and optical depth 10.

  5. Evidence of Longitudinal Acoustic Phonon Generation in Si Doping Superlattices by Ge Prism-Coupled THz Laser Radiation

    NASA Astrophysics Data System (ADS)

    Wilson, T.; Kasper, E.; Oehme, M.; Schulze, J.; Korolev, K.

    2014-11-01

    We report on the direct excitation of 246 GHz longitudinal acoustic phonons in silicon doping superlattices by the resonant absorption of nanosecond-pulsed far-infrared laser radiation of the same frequency. A longitudinally polarized evanescent laser light field is coupled to the superlattice through a germanium prism providing total internal reflection at the superlattice interface. The ballistic phonon signal is detected by a superconducting aluminum bolometer. The sample is immersed in low-temperature liquid helium.

  6. Broadband mid-infrared wavelength conversion laser based on Cr2+ doped ceramic materials

    NASA Astrophysics Data System (ADS)

    Shang, Yaping; Yin, Ke; Li, Xiao; Wang, Peng; Xu, Xiaojun

    2015-10-01

    Broadband mid-infrared lasers are desirable for pretty important applications in fields of environmental protection, medical treatment, military applications, scientific, and other domains. Recently, super-continuum laser sources have achieved striking development. However, limited by the substrate materials, the output power scaling of the broadband mid-infrared fiber laser sources could not be increased drastically, especially for the long wavelength region. In this paper, we reported an experimental study about the broadband mid-infrared lasers based on Cr2+ doped II-VI ceramic materials, by using of a super-continuum laser source developed by our groups operating at 1550~2130nm with 200mW output power. The result suggested that the near-infrared spectral component of the super-continuum source was deeply absorbed by transition metal doped zinc chalcogenides ceramic materials, meanwhile the mid-infrared part, however, had been enhanced significantly by this new "power amplifier." Actually single-pass amplification efficiency was very limited. The best way to solve this problem was multi-pass amplification systems. We had shown an initial proof of this assumption by a double-pass experiments, the result was consistent with expected effect. Above all, the spectrum shaping from short wavelength to long wavelength was obtained. The innovative discovery had laid a solid foundation for high power, high efficiency, broadly tunable mid-infrared solid state lasers.

  7. Femtosecond measurements of near-infrared pulse induced mid-infrared transmission modulation of quantum cascade lasers

    SciTech Connect

    Cai, Hong; Liu, Sheng; Lalanne, Elaine; Guo, Dingkai; Chen, Xing; Choa, Fow-Sen; Wang, Xiaojun; Johnson, Anthony M.

    2014-05-26

    We temporally resolved the ultrafast mid-infrared transmission modulation of quantum cascade lasers (QCLs) using a near-infrared pump/mid-infrared probe technique at room temperature. Two different femtosecond wavelength pumps were used with photon energy above and below the quantum well (QW) bandgap. The shorter wavelength pump modulates the mid-infrared probe transmission through interband transition assisted mechanisms, resulting in a high transmission modulation depth and several nanoseconds recovery lifetime. In contrast, pumping with a photon energy below the QW bandgap induces a smaller transmission modulation depth but much faster (several picoseconds) recovery lifetime, attributed to intersubband transition assisted mechanisms. The latter ultrafast modulation (>60 GHz) could provide a potential way to realize fast QCL based free space optical communication.

  8. Low-level infrared laser modulates muscle repair and chromosome stabilization genes in myoblasts.

    PubMed

    da Silva Neto Trajano, Larissa Alexsandra; Stumbo, Ana Carolina; da Silva, Camila Luna; Mencalha, Andre Luiz; Fonseca, Adenilson S

    2016-08-01

    Infrared laser therapy is used for skeletal muscle repair based on its biostimulative effect on satellite cells. However, shortening of telomere length limits regenerative potential in satellite cells, which occurs after each cell division cycle. Also, laser therapy could be more effective on non-physiologic tissues. This study evaluated low-level infrared laser exposure effects on mRNA expression from muscle injury repair and telomere stabilization genes in myoblasts in normal and stressful conditions. Laser fluences were those used in clinical protocols. C2C12 myoblast cultures were exposed to low-level infrared laser (10, 35, and 70 J/cm(2)) in standard or normal (10 %) and reduced (2 %) fetal bovine serum concentrations; total RNA was extracted for mRNA expression evaluation from muscle injury repair (MyoD and Pax7) and chromosome stabilization (TRF1 and TRF2) genes by real time quantitative polymerization chain reaction. Data show that low-level infrared laser increases the expression of MyoD and Pax7 in 10 J/cm(2) fluence, TRF1 expression in all fluences, and TRF2 expression in 70 J/cm(2) fluence in both 10 and 2 % fetal bovine serum. Low-level infrared laser increases mRNA expression from genes related to muscle repair and telomere stabilization in myoblasts in standard or normal and stressful conditions. PMID:27220530

  9. Water-ion transmembrane transfer under the effect of low-intensity laser radiation

    NASA Astrophysics Data System (ADS)

    Anisimov, A. V.; Vorob'ev, V. N.; Silkin, N. I.

    1997-09-01

    Water-ion transmembrane transfer in maize roots under the effect of infrared laser radiation with power 2.4 mwatt was studied by NMR method. It is shown that laser radiation (LR) alters the dynamics of spin-spin relaxation and increases the rate of transmembrane water exchange and ion penetration which do not depend on the type of paramagnetic ions doped into the intercellular space. The radiation results in the increase of the effective self-diffusion coefficient of water, and it correlates with the data on the effect of LR on the velocity of cytoplasm movement. The data on the decrease of the resistance of Nernst layers in the summary membrane permeability due to 'blowing off' its outer parts by the intensive cytoplasm current are used to explain the obtained results.

  10. Design theory, materials selection, and fabrication of hollow core waveguides for infrared to THz radiation

    NASA Astrophysics Data System (ADS)

    Bowden, Bradley F.

    Hollow core waveguides (HCWs) are comprised of a central hole surrounded by a highly reflective inner wall. The core can be filled with air, inert gas, or vacuum, allowing these waveguides to transmit a broad range of wavelengths with low attenuation. HCWs are of particular interest for the transmission of infrared (IR) to THz radiation, where it is otherwise difficult to find materials that have the optical, thermal, and mechanical properties required for use in solid core optical fibers. Ray optics calculations are used to predict the attenuation of the low-loss Gaussian-like HE11 mode propagating in two types of HCWs: hollow Bragg fibers (HBFs) and metal/dielectric hollow glass waveguides (HGWs). These calculations provide guidance on the materials selection and design of HCWs optimized for CO2 (10.6 mum) IR laser radiation and CO2 pumped CH3OH (119 mum) THz laser radiation. An all-chalcogenide glass HBF is proposed for the delivery of CO 2 laser radiation. Such a fiber would combine a high refractive index contrast (ratio of the high to low refractive index) with low materials absorption, characteristics that are critical to the design of a low loss HBF. Ge 20Se80 glass (nlambda=10.6 mum = 2.46 + i9.7e-7) is identified as an excellent candidate for the low refractive index composition due to its thermal stability and relatively low refractive index among chalcogenide glasses that transmit 10.6 mum radiation. To identify a high refractive index glass to combine with Ge20Se80, several glass compositions in the Ag-As-Se glass forming system are characterized using FTIR spectroscopy, CO2 laser variable angle reflectometry, and CO2 laser calorimetry. Of the compositions investigated, Ag 25As40Se35 glass (nlambda=10.6 mum = 3.10 + i1.7e-6) has the best thermal and optical properties for this application. Ray optics calculations show that a HBF made from alternating layers of Ge20Se80 and Ag25As40Se 35 glass could have orders of magnitude lower loss than any IR

  11. Optical radiation hazards of laser welding processes. Part 1: Neodymium-YAG laser.

    PubMed

    Rockwell, R J; Moss, C E

    1983-08-01

    High power laser devices are being used for numerous metalworking processes such as welding, cutting and heat treating. Such laser devices are totally enclosed either by the manufacturer or the end-user. When this is done, the total laser system is usually certified by the manufacturer following the federal requirements of the Code of Federal Regulations (CFR) 1040.10 and 10.40.11 as a Class I laser system. Similarly, the end-user may also reclassify an enclosed high-power laser into the Class I category following the requirements of the American National Standards Institute (ANSI) Z-136.1 (1980) standard. There are, however, numerous industrial laser applications where Class IV systems are required to be used in an unenclosed manner. In such applications, there is concern for both ocular and skin hazards caused by direct and scattered laser radiation, as well as potential hazards caused by the optical radiation created by the laser beam's interaction with the metal (i.e. the plume radiation). Radiant energy measurements are reported for both the scattered laser radiation and the resultant plume radiations which were produced during typical unenclosed Class IV Neodymium-YAG laser welding processes. Evaluation of the plume radiation was done with both radiometric and spectroradiometric measurement equipment. The data obtained were compared to applicable safety standards. PMID:6688700

  12. Analysis of the selected optical parameters of filters protecting against hazardous infrared radiation

    PubMed Central

    Gralewicz, Grzegorz; Owczarek, Grzegorz

    2016-01-01

    The paper analyses the selected optical parameters of protective optic filters used for protection of the eyes against hazardous radiation within the visible (VIS) and near infrared (NIR) spectrum range. The indexes characterizing transmission and reflection of optic radiation incident on the filter are compared. As it follows from the completed analysis, the newly developed interference filters provide more effective blocking of infrared radiation in comparison with the currently used protective filters. PMID:26327153

  13. Magnetic Field Discontinuity as a New Brighter Source of Infrared Synchrotron Radiation

    NASA Astrophysics Data System (ADS)

    Mathis, Y.-L.; Roy, P.; Tremblay, B.; Nucara, A.; Lupi, S.; Calvani, P.; Gerschel, A.

    1998-02-01

    Strong emission of highly collimated infrared radiation demonstrates the presence of dipole edge emission and transient undulator radiation emission. The photon flux and spatial distribution for the Super-ACO sources (both dipole edge and wiggler) including coherence effects have been evaluated using the exact expression for the emission of a charged particle. The excellent agreement between these results and measurements performed at the SIRLOIN (Spectroscopie en Infrarouge LOINtain) beam line provides a new level of understanding of infrared synchrotron radiation.

  14. Analysis of the selected optical parameters of filters protecting against hazardous infrared radiation.

    PubMed

    Gralewicz, Grzegorz; Owczarek, Grzegorz

    2016-09-01

    The paper analyses the selected optical parameters of protective optic filters used for protection of the eyes against hazardous radiation within the visible (VIS) and near infrared (NIR) spectrum range. The indexes characterizing transmission and reflection of optic radiation incident on the filter are compared. As it follows from the completed analysis, the newly developed interference filters provide more effective blocking of infrared radiation in comparison with the currently used protective filters. PMID:26327153

  15. [Calculation and simulation on infrared radiation of hot jet from engine].

    PubMed

    Li, Jian-Xun; Tong, Zhong-Xiang; Wang, Chao-Zhe; Tong, Qi; Li, He; Zhang, Zhi-Bo

    2013-01-01

    Spectral distribution of infrared radiation from plume by the method to calculate infrared radiance of the gaze direction in small sight field was calculated. Based on numerical value and form of radiative transfer equation, infrared radiant intensity of the gaze direction was calculated using the Malkmus statistical narrow-band model and CG approach. Flow field and mole fraction distribution were simulated using a FLUENT computational fluid dynamic (CFD) software. Infrared imaging simulation model of hot jet was established. The hot jet's infrared images of liquid rocket engine were generated. The results demonstrate that the method can detect well-resolved fine structure of flow field. And the model is also applicable to calculation and simulation on infrared radiation of hot jet from engine. PMID:23586213

  16. Mid-infrared laser emission from Cr:ZnS channel waveguide fabricated by femtosecond laser helical writing.

    PubMed

    Peng, Ya-Pei; Zou, Xiao; Bai, Zhengyuan; Leng, Yuxin; Jiang, Benxue; Jiang, Xiongwei; Zhang, Long

    2015-01-01

    The operation of a mid-infrared laser at 2244 nm in a Cr:ZnS polycrystalline channel waveguide fabricated using direct femtosecond laser writing with a helical movement technique is demonstrated. A maximum power output of 78 mW and an optical-to-optical slope efficiency of 8.6% are achieved. The compact waveguide structure with 2 mm length was obtained through direct femtosecond laser writing, which was moved on a helical trajectory along the laser medium axis and parallel to the writing direction. PMID:26692268

  17. Mid-infrared laser emission from Cr:ZnS channel waveguide fabricated by femtosecond laser helical writing

    PubMed Central

    Peng, Ya-Pei; Zou, Xiao; Bai, Zhengyuan; Leng, Yuxin; Jiang, Benxue; Jiang, Xiongwei; Zhang, Long

    2015-01-01

    The operation of a mid-infrared laser at 2244 nm in a Cr:ZnS polycrystalline channel waveguide fabricated using direct femtosecond laser writing with a helical movement technique is demonstrated. A maximum power output of 78 mW and an optical-to-optical slope efficiency of 8.6% are achieved. The compact waveguide structure with 2 mm length was obtained through direct femtosecond laser writing, which was moved on a helical trajectory along the laser medium axis and parallel to the writing direction. PMID:26692268

  18. FAST TRACK COMMUNICATION: Selective inactivation of human immunodeficiency virus with subpicosecond near-infrared laser pulses

    NASA Astrophysics Data System (ADS)

    Tsen, K. T.; Tsen, Shaw-Wei D.; Hung, Chien-Fu; Wu, T.-C.; Kiang, Juliann G.

    2008-06-01

    We demonstrate for the first time that human immunodeficiency virus (HIV) can be inactivated by irradiation with subpicosecond near-infrared laser pulses at a moderate laser power density. By comparing the threshold laser power density for the inactivation of HIV with those of human red blood cells and mouse dendritic cells, we conclude that it is plausible to use the ultrashort pulsed laser to selectively inactivate blood-borne pathogens such as HIV while leaving sensitive materials like human red blood cells unharmed. This finding has important implications in the development of a new laser technology for disinfection of viral pathogens in blood products and in the clinic.

  19. Near-infrared distributed feedback solgel lasers by intensity modulation and polarization modulation.

    PubMed

    Wang, Jun; Dong, Hongxing; Fan, Jintai; Li, Rihong; Zhang, Long; Wong, King Y

    2011-11-20

    Near-infrared distributed feedback (DFB) laser actions of Oxazine 725 dye in zirconia thin films and in silica bulks were investigated. Intensity modulation and polarization modulation were used to generate the DFB lasing. Wideband tuning of the output wavelength was achieved by varying the period of the modulation generated by a nanosecond Nd:YAG laser at 532 nm. Tuning ranges were 716-778 nm and 724-813 nm for the thin film lasers and the bulk lasers, respectively. The laser output showed different polarization characteristics and threshold energy variation when the feedback mechanism was changed from intensity modulation to polarization modulation. PMID:22108883

  20. Infrared/laser multi-sensor fusion and tracking based on the multi-scale model

    NASA Astrophysics Data System (ADS)

    Wang, Bingjian; Hao, Jingya; Yi, Xiang; Wu, Feihong; Li, Min; Qin, Hanlin; Huang, Hanqiao

    2016-03-01

    The state estimation problem of targets detected by infrared/laser composite detection system with different sampling rates was studied in this paper. An effective state estimation algorithm based on data fusion is presented. Because sampling rate of infrared detection system is much higher than that of the laser detection system, the theory of multi-scale analysis is used to establish multi-scale model in this algorithm. At the fine scale, angle information provided by infrared detection system is used to estimate the target state through the unscented Kalman filter. It makes full use of the high frequency characteristic of infrared detection system to improve target state estimation accuracy. At the coarse scale, due to the sampling ratio of infrared and laser detection systems is an integer multiple, the angle information can be fused directly with the distance information of laser detection system to determine the target location. The fused information is served as observation, while the converted measurement Kalman filter (CMKF) is used to estimate the target state, which greatly reduces the complexity of filtering process and gets the optimal fusion estimation. The simulation results of tracking a target in 3-D space by infrared and laser detection systems demonstrate that the proposed algorithm in this paper is efficient and can obtain better performance than traditional algorithm.

  1. Continuous-wave violet generation at 373.5 nm by frequency-doubled power-scaled near-infrared emitting Pr:YAlO3 laser

    NASA Astrophysics Data System (ADS)

    Fibrich, Martin; Jelínková, Helena

    2013-10-01

    We report on a continuous-wave Pr:YAlO3 laser operating at a wavelength of 373.5 nm in a power-scaled resonator arrangement. Violet light generation has been achieved by intracavity frequency doubling of the near-infrared emitting Pr:YAP laser at a fundamental wavelength of 747 nm. For active medium pumping, two GaN laser diodes providing up to 1 W of output power each at 448 nm were used. By employing BBO crystal as a nonlinear medium, more than 46 mW of violet radiation has been obtained.

  2. Near-infrared laser ablation of poly tetrafluoroethylene (Teflon) sensitized by nanoenergetic materials

    SciTech Connect

    Yang Yanqiang; Wang Shufeng; Sun Zhaoyong; Dlott, Dana D.

    2004-08-30

    Laser ablation of Teflon doped with size-selected (30-250 nm) Al nanoparticles is studied. Unlike pure Teflon, which requires a vacuum-ultraviolet or femtosecond excimer laser for ablation, this sensitized Teflon can be ablated with a near-infrared laser. Using 100 ps duration pulses, near-infrared ablation thresholds are lower by about a factor of 10 from excimer ablation of pure Teflon. A mechanism is discussed that involves Teflon decomposition by spherical shock fronts originating at each irradiated nanoparticle. Studies of the distance dependence of this process as a function of particle diameter and oxide layer thickness suggest ways of optimizing the ablation process.

  3. A New Technology for Applanation Free Corneal Trephination: The Picosecond Infrared Laser (PIRL)

    PubMed Central

    Linke, Stephan J.; Frings, Andreas; Ren, Ling; Gomolka, Amadeus; Schumacher, Udo; Reimer, Rudolph; Hansen, Nils-Owe; Jowett, Nathan; Richard, Gisbert; Miller, R. J. Dwayne

    2015-01-01

    The impact of using a Femtosecond laser on final functional results of penetrating keratoplasty is low. The corneal incisions presented here result from laser ablations with ultrafast desorption by impulsive vibrational excitation (DIVE). The results of the current study are based on the first proof-of-principle experiments using a mobile, newly introduced picosecond infrared laser system, and indicate that wavelengths in the mid-infrared range centered at 3 μm are efficient for obtaining applanation-free deep cuts on porcine corneas. PMID:25781907

  4. Comparison of laser-based mitigation of fused silica surface damage using mid- versus far-infrared lasers

    SciTech Connect

    Yang, S T; Matthews, M J; Elhadj, S; Cooke, D; Guss, G M; Draggoo, V G; Wegner, P J

    2009-12-16

    Laser induced growth of optical damage can limit component lifetime and therefore operating costs of large-aperture fusion-class laser systems. While far-infrared (IR) lasers have been used previously to treat laser damage on fused silica optics and render it benign, little is known about the effectiveness of less-absorbing mid-IR lasers for this purpose. In this study, they quantitatively compare the effectiveness and efficiency of mid-IR (4.6 {micro}m) versus far-IR (10.6 {micro}m) lasers in mitigating damage growth on fused silica surfaces. The non-linear volumetric heating due to mid-IR laser absorption is analyzed by solving the heat equation numerically, taking into account the temperature-dependent absorption coefficient {alpha}(T) at {lambda} = 4.6 {micro}m, while far-IR laser heating is well-described by a linear analytic approximation to the laser-driven temperature rise. In both cases, the predicted results agree well with surface temperature measurements based on infrared radiometry, as well as sub-surface fictive temperature measurements based on confocal Raman microscopy. Damage mitigation efficiency is assessed using a figure of merit (FOM) relating the crack healing depth to laser power required, under minimally-ablative conditions. Based on their FOM, they show that for cracks up to at least 500 {micro}m in depth, mitigation with a 4.6 {micro}m mid-IR laser is more efficient than mitigation with a 10.6 {micro}m far-IR laser. This conclusion is corroborated by direct application of each laser system to the mitigation of pulsed laser-induced damage possessing fractures up to 225 {micro}m in depth.

  5. Daytime Observations with ELTs in the Thermal Infrared Using Laser Guide Star Adaptive Optics

    NASA Astrophysics Data System (ADS)

    Beckers, J. M.

    2011-09-01

    Using Magneto-Optical Filters (MOFs; also called FADOFs = Faraday Anomalous Dispersion Optical Filters) it is possible to clearly see Sodium Laser Guide Stars in the daytime sky. This makes it possible to use ELT Adaptive Optics systems for diffraction limited observations 24 hours/day. Because of the bright daytime sky this LGS AO application is only of astronomical interest in the mid-infrared wavelength region (4 - 25 microns wavelengths) where the thermal radiation of the atmosphere-telescope system dominates the scattering of sunlight thus making the day- and night- sky background comparable. Incorporating MOFs in the LGS wavefront sensor thus would more than double the ELT observing time for mid-infrared astronomy and would make sources in almost the entire sky available for observation at any time of the year. Even though the AO would increase the brightness of point-sources, it would not compete with the James Webb Space Telescope in terms of detectability. The gain with respect to the JWST lies in the 5 to 6 times better linear angular resolution. The contrast gain in brightness at near-IR wavelengths is sufficient to give sufficient natural guide stars there for tip-tilt control. MOFs have been shown to function with Na lasers in LIDAR applications (see Beckers and Cacciani, Experimental Astronomy 11, 133, 2001). The main complication associated with incorporating MOFs in ELT AO system is likely the requirement to make the telescope and its enclosure robust in the daytime environment. I refer to SPIE Proceedings 6986 (2008) for a recent reference on this topic.

  6. Backward Monte Carlo analysis on stray radiation of an infrared optical system

    NASA Astrophysics Data System (ADS)

    Chen, Xue; Sun, Chuang; Xia, Xinlin

    2013-09-01

    In an infrared optical system, the thermal radiation of high temperature components is the major noise as stray radiation that degrades the system performance. Backward Monte Carlo method based on radiation distribution factor is proposed to perform the stray radiation calculation. Theoretical deduction and some techniques are presented, considering the semitransparent element like IR window as radiation emitter. The radiation distribution factors are calculated with ray tracing from the detector to radiation sources. Propagation of stray radiation and its distribution on the detector are obtained simultaneously. It is unnecessary to implement ray tracing again to study the effect of different temperatures for a given system, expect that the geometry or radiative property is changed. An infrared system is simulated using this method. Two different situations are discussed and the analysis shows that stray radiation is mainly created by IR window and lens tube.

  7. Atmospheric influences on infrared-laser signals used for occultation measurements between Low Earth Orbit satellites

    NASA Astrophysics Data System (ADS)

    Schweitzer, S.; Kirchengast, G.; Proschek, V.

    2011-05-01

    LEO-LEO infrared-laser occultation (LIO) is a new occultation technique between Low Earth Orbit (LEO) satellites, which applies signals in the short wave infrared spectral range (SWIR) within 2 μm to 2.5 μm. It is part of the LEO-LEO microwave and infrared-laser occultation (LMIO) method, recently introduced by Kirchengast and Schweitzer (2011), that enables to retrieve thermodynamic profiles (pressure, temperature, humidity) and accurate altitude levels from microwave signals and profiles of greenhouse gases and further variables such as line-of-sight wind speed from simultaneously measured LIO signals. For enabling trace species retrieval based on differential transmission, the LIO signals are spectrally located as pairs, one in the centre of a suitable absorption line of a target species (absorption signal) and one close by but outside of any absorption lines (reference signal). Due to the novelty of the LMIO method, detailed knowledge of atmospheric influences on LIO signals and of their suitability for accurate trace species retrieval did not yet exist. Here we discuss the atmospheric influences on the transmission and differential transmission of LIO signals. Refraction effects, trace species absorption (by target species, and cross-sensitivity to foreign species), aerosol extinction and Rayleigh scattering are studied in detail. The influences of clouds, turbulence, wind, scattered solar radiation and terrestrial thermal radiation are discussed as well. We show that the influence of defocusing, foreign species absorption, aerosols and turbulence is observable, but can be rendered small to negligible by use of the differential transmission principle and by a design with close frequency spacing of absorption and reference signals within 0.5 %. The influences of Rayleigh scattering and thermal radiation on the received signal intensities are found negligible. Cloud-scattered solar radiation can be observable under bright-day conditions but this influence can

  8. [Infrared tunable difference frequency laser source]. Final technical report, September 15, 1990--September 14, 1992

    SciTech Connect

    Curl, R.F.

    1992-01-01

    Purpose of grant was to purchase equipment necessary to construct an infrared laser source based on difference frequency generation in AgGaS[sub 2]. This continuous wave, single frequency, tunable infrared source has been assembled and is being used for infrared kinetic spectroscopy of small free radicals important in combustion. Infrared spectra are given for the Q-branch of a combination band (11[sup 1]1) of N[sub 2]O, and for the transient in CO produced by flash photolysis of acetone in various vibrational states.

  9. [Infrared tunable difference frequency laser source]. Final technical report, September 15, 1990--September 14, 1992

    SciTech Connect

    Curl, R.F.

    1992-12-31

    Purpose of grant was to purchase equipment necessary to construct an infrared laser source based on difference frequency generation in AgGaS{sub 2}. This continuous wave, single frequency, tunable infrared source has been assembled and is being used for infrared kinetic spectroscopy of small free radicals important in combustion. Infrared spectra are given for the Q-branch of a combination band (11{sup 1}1) of N{sub 2}O, and for the transient in CO produced by flash photolysis of acetone in various vibrational states.

  10. Real-time quantum cascade laser-based infrared microspectroscopy in-vivo

    NASA Astrophysics Data System (ADS)

    Kröger-Lui, N.; Haase, K.; Pucci, A.; Schönhals, A.; Petrich, W.

    2016-03-01

    Infrared microscopy can be performed to observe dynamic processes on a microscopic scale. Fourier-transform infrared spectroscopy-based microscopes are bound to limitations regarding time resolution, which hampers their potential for imaging fast moving systems. In this manuscript we present a quantum cascade laser-based infrared microscope which overcomes these limitations and readily achieves standard video frame rates. The capabilities of our setup are demonstrated by observing dynamical processes at their specific time scales: fermentation, slow moving Amoeba Proteus and fast moving Caenorhabditis elegans. Mid-infrared sampling rates between 30 min and 20 ms are demonstrated.

  11. Infrared [Fe II] Emission Lines from Radiative Atomic Shocks

    NASA Astrophysics Data System (ADS)

    Koo, Bon-Chul; Raymond, John C.; Kim, Hyun-Jeong

    2016-06-01

    [Fe II] emission lines are prominent in the infrared (IR) and important as diagnostic tools for radiative atomic shocks. We investigate the emission characteristics of [Fe II] lines using a shock code developed by te{raymond1979} with updated atomic parameters. We first review general characteristics of the IR [Fe II] emission lines from shocked gas, and derive their fluxes as a function of shock speed and ambient density. We have compiled available IR [Fe II] line observations of interstellar shocks and compare them to the ratios predicted from our model. The sample includes both young and old supernova remnants in the Galaxy and the Large Magellanic Cloud and several Herbig-Haro objects. We find that the observed ratios of the IR [Fe II] lines generally fall on our grid of shock models, but the ratios of some mid-IR lines, e.g., fethreefive/fetwofive, fefive/fetwofive, and fefive/feoneseven, are significantly offset from our model grid. We discuss possible explanations and conclude that while uncertainties in the shock modeling and the observations certainly exist, the uncertainty in atomic rates appears to be the major source of discrepancy.

  12. Mathematical modeling of a photovoltaic-laser energy converter for iodine laser radiation

    NASA Technical Reports Server (NTRS)

    Walker, Gilbert H.; Heinbockel, John H.

    1987-01-01

    Space-based laser power systems will require converters to change laser radiation into electricity. Vertical junction photovoltaic converters are promising devices for this use. A promising laser for the laser power station is the t-C4F9I laser which emits radiation at a wavelength of 1.315 microns. This paper describes the results of mathematical modeling of a photovoltaic-laser energy converter for use with this laser. The material for this photovoltaic converter is Ga(53)In(47)As which has a bandgap energy of 0.94 eV, slightly below the energy of the laser photons (0.943 eV). Results of a study optimizing the converter parameters are presented. Calculated efficiency for a 1000 vertical junction converter is 42.5 percent at a power density of 1 x 10 to the 3d power w/sq cm.

  13. Biological Effects of Sunlight, Ultraviolet Radiation, Visible Light, Infrared Radiation and Vitamin D for Health.

    PubMed

    Holick, Michael F

    2016-03-01

    Humans evolved in sunlight and had depended on sunlight for its life giving properties that was appreciated by our early ancestors. However, for more than 40 years the lay press and various medical and dermatology associations have denounced sun exposure because of its association with increased risk for skin cancer. The goal of this review is to put into perspective the many health benefits that have been associated with exposure to sunlight, ultraviolet A (UVA) ultraviolet B (UVB), visible and infrared radiation. PMID:26977036

  14. Plasma lasers (a strong source of coherent radiation in astrophysics)

    NASA Technical Reports Server (NTRS)

    Papadopoulos, K.

    1981-01-01

    The generation of electromagnetic radiation from the free energy available in electron streams is discussed. The fundamental principles involved in a particular class of coherent plasma radiation sources, i.e., plasma lasers, are reviewed, focusing on three wave coupling, nonlinear parametric instabilities, and negative energy waves. The simplest case of plasma lasers, that of an unmagnetized plasma containing a finite level of density fluctuations and electrons streaming with respect to the ions, is dealt with. A much more complicated application of plasma lasers to the case of auroral kilometric radiation is then examined. The concept of free electron lasers, including the role of relativistic scattering, is elucidated. Important problems involving the escape of the excited radiation from its generation region, effects due to plasma shielding and nonlinear limits, are brought out.

  15. Studies of new media radiation induced laser

    NASA Technical Reports Server (NTRS)

    Han, K. S.; Shiu, Y. J.; Raju, S. R.; Hwang, I. H.; Tabibi, B.

    1984-01-01

    Various lasants were investigated especially, 2-iodohepafluoropropane (i-C3F7I) for the direct solar pumped lasers. Optical pumping of iodine laser was achieved using a small flashlamp. Using i-C3F7I as a laser gain medium, threshold inversion density, small signal gain, and laser performance at the elevated temperature were measured. The experimental results and analysis are presented. The iodine laser kinetics of the C3F7I and IBr system were numerically simulated. The concept of a direct solar-pumped laser amplifier using (i-C3F7I) as the laser material was evaluated and several kinetic coefficients for i-C3F7I laser system were reexamined. The results are discussed.

  16. Sub GV/cm terahertz radiation from relativistic laser-solid interactions via coherent transition radiation

    NASA Astrophysics Data System (ADS)

    Ding, W. J.; Sheng, Z. M.

    2016-06-01

    Broadband terahertz (THz) radiation with extremely high peak power, generated by the interaction of a femtosecond laser with a thin solid target, has been investigated via particle-in-cell simulations. The spatial (angular) and temporal profiles of the THz radiation reveal that it is caused by the coherent transition radiation emitted when laser-produced hot electrons pass through the front or rear surface of the target. Dependence of the THz radiation on laser and target parameters is studied; it is shown to have a strong correlation with hot electron production. The THz radiation conversion efficiency can be as high as a few times 10-3. This radiation is not only a potentially high power THz source, but may also be used as a unique diagnostic of hot electron generation and transport in relativistic laser-solid interactions.

  17. Radiative heat transport instability in a laser produced inhomogeneous plasma

    SciTech Connect

    Bychenkov, V. Yu.; Rozmus, W.

    2015-08-15

    A laser produced high-Z plasma in which an energy balance is achieved due to radiation emission and radiative heat transfer supports ion acoustic instability. A linear dispersion relation is derived, and instability is compared to the radiation cooling instability [R. G. Evans, Plasma Phys. Controlled Fusion 27, 751 (1985)]. Under conditions of indirect drive fusion experiments, the driving term for the instability is the radiative heat flux and, in particular, the density dependence of the radiative heat conductivity. A specific example of thermal Bremsstrahlung radiation source has been considered. This instability may lead to plasma jet formation and anisotropic x-ray generation, thus affecting inertial confinement fusion related experiments.

  18. Thermal effects of laser radiation in biological tissue.

    PubMed Central

    Cummins, L; Nauenberg, M

    1983-01-01

    A theoretical model is presented that simulates the thermal effects of laser radiation incident on biological tissue. The multiple scattering and absorption of the laser beam and the thermal diffusion process in the tissue are evaluated by a numerical technique that is well suited for microcomputers. Results are compared with recent empirical observations. PMID:6838985

  19. Laser therapy for severe radiation-induced rectal bleeding

    SciTech Connect

    Ahlquist, D.A.; Gostout, C.J.; Viggiano, T.R.; Pemberton, J.H.

    1986-12-01

    Four patients with chronic hematochezia and transfusion-dependent anemia from postradiation rectal vascular lesions were successfully managed by endoscopic laser coagulation. In all four patients, symptomatic, hematologic, and endoscopic improvement was evident. Laser therapy for severe radiation-induced rectal bleeding seems to be safe and efficacious and should be considered before surgical intervention.

  20. A blackbody radiation-pumped CO2 laser experiment

    NASA Astrophysics Data System (ADS)

    Christiansen, W. H.; Insuik, R. J.; Deyoung, R. J.

    1982-09-01

    Thermal radiation from a high temperature oven was used as an optical pump to achieve lasing from CO2 mixtures. Laser output as a function of blackbody temperature and gas conditions is described. This achievement represents the first blackbody cavity pumped laser and has potential for solar pumping.

  1. Laser radiation and motility patterns of human sperm

    SciTech Connect

    Lenzi, A.; Claroni, F.; Gandini, L.; Lombardo, F.; Barbieri, C.; Lino, A.; Dondero, F. )

    1989-01-01

    Human sperm were exposed in vitro to laser radiation. An increase in progressive sperm motility was associated with a faster rate of sperm ATP consumption. Computer-assisted analysis of sperm motility confirmed the positive effect of laser irradiation on velocity and linearity of sperm.

  2. New solid state lasers from the ultraviolet to the mid-infrared

    SciTech Connect

    Payne, S.A.; Krupke, W.F.; Beach, R.J.

    1995-08-15

    The authors discuss three new laser materials that offer improved access to the ultraviolet, near infrared and mid-infrared spectral regions. In order for each of these materials to have been identified, a particular hurdle needed to be overcome with respect to the fundamental laser physics impacting the material. In the case of the 280-320nm Ce:LiSAF laser, the main issue is the need to reduce the loss associated with excited state absorption, while for 1047nm Yb:S-FAP it is the ground state absorption at the laser wavelength that must be minimized. Cr:ZnSe has been down-selected from a number of potential candidates which could lase in the 2200-3000nm region, in order to mitigate the detrimental impact of nonradiative decay. In all three cases the authors discuss how appropriate consideration of fundamental concerns has led to the identification and understanding of the new laser system.

  3. Overcoming the specific power limitations of nuclear electric propulsion by laser radiators

    NASA Astrophysics Data System (ADS)

    Winterberg, F.

    1997-07-01

    It is shown that the specific power of nuclear electric propulsion can be greatly increased by replacing black body radiators with laser radiators. In black body radiators the atomic oscillators have a random phase with the emission rate for black body radiators proportional to the sum of the squared amplitudes. In laser radiators the oscillators are all in phase with the emission rate proportional to the squared sum of the amplitudes, which is the reason for the much larger emission rate of laser radiators. In a laser radiator the low entropy low temperature laser beam removes the waste heat by resonance absorption and isotropic reemission of the laser radiation into space.

  4. Viability of fibroblasts cultured under nutritional stress irradiated with red laser, infrared laser, and red light-emitting diode

    NASA Astrophysics Data System (ADS)

    Volpato, Luiz Evaristo Ricci; de Oliveira, Rodrigo Cardoso; Espinosa, Mariano Martinez; Bagnato, Vanderley Salvador; Machado, Maria A. A. M.

    2011-07-01

    Phototherapy is noninvasive, painless and has no known side effect. However, for its incorporation into clinical practice, more well-designed studies are necessary to define optimal parameters for its application. The viability of fibroblasts cultured under nutritional stress irradiated with either a red laser, an infrared laser, or a red light-emitting diode (LED) was analyzed. Irradiation parameters were: red laser (660 nm, 40 mW, 1 W/cm2), infrared laser (780 nm, 40 mW, 1 W/cm2), and red LED (637 +/- 15 nm, 40 mW, 1 W/cm2). All applications were punctual and performed with a spot with 0.4 mm2 of diameter for 4 or 8 s. The Kruskal-Wallis test and analysis of variance of the general linear model (p <= 0.05) were used for statistical analysis. After 72 h, phototherapy with low-intensity laser and LED showed no toxicity at the cellular level. It even stimulated methylthiazol tetrazolium assay (MTT) conversion and neutral red uptake of fibroblasts cultured under nutritional stress, especially in the group irradiated with infrared laser (p = 0.004 for MTT conversion and p < 0.001 for neutral red uptake). Considering the parameters and protocol of phototherapy used, it can be concluded that phototherapy stimulated the viability of fibroblasts cultured under nutritional deficit resembling those found in traumatized tissue in which cell viability is reduced.

  5. Research on radiation induced laser plasmas

    NASA Technical Reports Server (NTRS)

    Schneider, R. T.; Rowe, M. J.; Carter, B. D.; Walters, R. A.; Cox, J. D.; Liang, R.; Roxey, T.; Zapata, L.

    1979-01-01

    The development of high power nuclear pumped lasers is discussed. The excitation mechanism of continuous wave (CW) HeNe nuclear pumped lasers is studied and a CO2 nuclear pumped laser is used to demonstrate the CW output in the order of watts. The assumption that high power densities are only achievable by volume fission fragment sources is used to identify laser gases which are compatible with UF6 by excited states lifetime measurements. The examination of Xe2, XeF, and KrF under nuclear irradiation to determine if they are good candidates for nuclear-pumped lasers is described.

  6. Mid-Infrared Pumped Laser-Induced Thermal Grating Spectroscopy for Detection of Acetylene in the Visible Spectral Range.

    PubMed

    Sahlberg, Anna-Lena; Kiefer, Johannes; Aldén, Marcus; Li, Zhongshan

    2016-06-01

    We present mid-infrared laser-induced thermal grating spectroscopy (IR-LITGS) using excitation radiation around 3 µm generated by a simple broadband optical parametric oscillator (OPO). Acetylene as a typical small hydrocarbon molecule is used as an example target species. A mid-infrared broadband OPO pumped by the fundamental output of a neodymium-doped yttrium aluminum garnet (Nd:YAG) laser was used to generate the pump beams, with pulse energies of 6-10 mJ depending on the wavelength. The line width of the OPO idler beam was ∼5 cm(-1), which is large enough to cover up to six adjacent acetylene lines. The probe beam was the radiation of a 532 nm cw solid state laser with 190 mW output power. Signals were generated in atmospheric pressure gas flows of N2, air, CO2 and Ar with small admixtures of C2H2 A detection limit of less than 300 ppm was found for a point measurement of C2H2 diluted in N2 As expected, the oscillation frequency of the IR-LITGS signal was found to have a large dependency on the buffer gas, which allows determination of the speed of sound. Moreover, the results reveal a very strong collisional energy exchange between C2H2 and CO2 compared to the other gases. This manifests as significant local heating. In summary, the MIR-LITGS technique enables spectroscopy of fundamental vibrational transitions in the infrared via detection in the visible spectral range. PMID:27091904

  7. Optical radiation hazards of laser welding processes. Part II: CO2 laser.

    PubMed

    Rockwell, R J; Moss, C E

    1989-08-01

    There has been an extensive growth within the last five years in the use of high-powered lasers in various metalworking processes. The two types of lasers used most frequently for laser welding/cutting processes are the Neodymium-yttrium-aluminum-garnet (Nd:YAG) and the carbon dioxide (CO2) systems. When such lasers are operated in an open beam configuration, they are designated as a Class IV laser system. Class IV lasers are high-powered lasers that may present an eye and skin hazard under most common exposure conditions, either directly or when the beam has been diffusely scattered. Significant control measures are required for unenclosed (open beam), Class IV laser systems since workers may be exposed to scattered or reflected beams during the operation, maintenance, and service of these lasers. In addition to ocular and/or skin exposure hazards, such lasers also may present a multitude of nonlaser beam occupational concerns. Radiant energy measurements are reported for both the scattered laser radiation and the plasma-related plume radiations released during typical high-powered CO2 laser-target interactions. In addition, the application of the nominal hazard zone (NHZ) and other control measures also are discussed with special emphasis on Class IV industrial CO2 laser systems. PMID:2508455

  8. Nanosurgery of cells and chromosomes using near-infrared twelve-femtosecond laser pulses

    NASA Astrophysics Data System (ADS)

    Uchugonova, Aisada; Lessel, Matthias; Nietzsche, Sander; Zeitz, Christian; Jacobs, Karin; Lemke, Cornelius; König, Karsten

    2012-10-01

    Laser-assisted surgery based on multiphoton absorption of near-infrared laser light has great potential for high precision surgery at various depths within the cells and tissues. Clinical applications include refractive surgery (fs-LASIK). The non-contact laser method also supports contamination-free cell nanosurgery. In this paper we describe usage of an ultrashort femtosecond laser scanning microscope for sub-100 nm surgery of human cells and metaphase chromosomes. A mode-locked 85 MHz Ti:Sapphire laser with an M-shaped ultrabroad band spectrum (maxima: 770 nm/830 nm) and an in situ pulse duration at the target ranging from 12 fs up to 3 ps was employed. The effects of laser nanoprocessing in cells and chromosomes have been quantified by atomic force microscopy. These studies demonstrate the potential of extreme ultrashort femtosecond laser pulses at low mean milliwatt powers for sub-100 nm surgery of cells and cellular organelles.

  9. Development of long wavelength semiconductor diode lasers near 28 microns for use in infrared heterodyne spectrometers

    NASA Technical Reports Server (NTRS)

    Linden, K. J.

    1984-01-01

    The development of tunable diode lasers operating in the 28 micrometers spectral region for use in infrared heterodyne spectrometers is reported. A process capable of yielding lasers emitting 500 micron W of multimode power, 112 micron W in a true single mode and true single mode operation at laser currents of up to 35% above threshold was developed. Results were obtained from narrow mesastripe (20 micrometer wide) short cavity (120 micrometer length) laser configurations. Six stripe geometry lasers, with a variety of cavity widths and lengths were delivered. The techniques to fabricate such devices was obtained and the long term reliability of such lasers by reproducible electrical and optical output characteristics fabrication from lasers are demonstrated.

  10. Near-infrared femtosecond laser-induced crystallization of amorphous silicon

    SciTech Connect

    Shieh, J.-M.; Chen, Z.-H.; Dai, B.-T.; Wang, Y.-C.; Zaitsev, Alexei; Pan, C.-L.

    2004-08-16

    Amorphous silicon (a-Si) was crystallized by femtosecond laser annealing (FLA) using a near-infrared ({lambda}{approx_equal}800 nm) ultrafast Ti:sapphire laser system. The intense ultrashort laser pulses lead to efficient nonlinear photoenergy absorption and the generation of very dense photoexcited plasma in irradiated materials, enabling nonlinear melting on transparent silicon materials. We studied the structural characteristics of recrystallized films and found that FLA assisted by spatial scanning of laser strip spot constitutes superlateral epitaxy that can crystallize a-Si films with largest grains of {approx}800 nm, requiring laser fluence as low as {approx}45 mJ/cm{sup 2}, and low laser shots. Moreover, the optimal annealing conditions are observed with a significant laser-fluence window ({approx}30%)

  11. Intercomparison of three microwave/infrared high resolution line-by-line radiative transfer codes

    NASA Astrophysics Data System (ADS)

    Schreier, F.; Garcia, S. Gimeno; Milz, M.; Kottayil, A.; Höpfner, M.; von Clarmann, T.; Stiller, G.

    2013-05-01

    An intercomparison of three line-by-line (lbl) codes developed independently for atmospheric sounding - ARTS, GARLIC, and KOPRA - has been performed for a thermal infrared nadir sounding application assuming a HIRS-like (High resolution Infrared Radiation Sounder) setup. Radiances for the HIRS infrared channels and a set of 42 atmospheric profiles from the "Garand dataset" have been computed. Results of this intercomparison and a discussion of reasons of the observed differences are presented.

  12. Simulation of phase conjugation for laser radiation upon nonstationary SBS

    SciTech Connect

    Bogachev, V A; Maslov, N V; Starikov, F A

    2010-06-23

    We report the three-dimensional simulation results of phase conjugation upon nonstationary stimulated Brillouin scattering of a focused laser beam. It is shown that in the case of deep focusing of laser radiation in the SBS cell, the phase conjugation quality decreases with increasing laser power and reflection coefficient, in agreement with experimental results. In calculations, the process of Stokes radiation generation is studied in detail, the reasons for a decrease in the phase conjugation quality are explained, and a means of its improvement is proposed. (nonlinear optical phenomena)

  13. Photobiological principles of therapeutic applications of laser radiation.

    PubMed

    Vladimirov, Yu A; Osipov, A N; Klebanov, G I

    2004-01-01

    Laser therapy based on the stimulating and healing action of light of low-intensity lasers (LIL), along with laser surgery and photodynamic therapy, has been lately widely applied in the irradiation of human tissues in the absence of exogenous photosensitizers. Besides LIL, light-emitting diodes are used in phototherapy (photobiostimulation) whose action, like that of LIL, depends on the radiation wavelength, dose, and distribution of light intensity in time but, according to all available data, does not depend on the coherence of radiation. PMID:14972023

  14. QED effects and radiation generation in relativistic laser plasma

    NASA Astrophysics Data System (ADS)

    Kostyukov, I. Yu.; Nerush, E. N.; Bashmakov, V. F.

    2011-06-01

    The radiative and quantum effects in laser plasmas are discussed. The self-consistent numerical model based on particle-in-cell and Monte-Carlo methods are developed. First we analyze the spectra of Compton backscattered photons and betatron radiation in the classical and quantum regimes. Then we address an interaction between intense laser pulse and relativistic electron beam. Finally we discuss the electron-positron pair plasma production in extremely-intense laser field. It is shown that such plasma can be an efficient source of energetic gammaquanta.

  15. Satellite Infrared Radiation Measurements Prior to the Major Earthquakes

    NASA Technical Reports Server (NTRS)

    Ouzounov, Dimitar; Pulintes, S.; Bryant, N.; Taylor, Patrick; Freund, F.

    2005-01-01

    This work describes our search for a relationship between tectonic stresses and increases in mid-infrared (IR) flux as part of a possible ensemble of electromagnetic (EM) phenomena that may be related to earthquake activity. We present and &scuss observed variations in thermal transients and radiation fields prior to the earthquakes of Jan 22, 2003 Colima (M6.7) Mexico, Sept. 28 .2004 near Parkfield (M6.0) in California and Northern Sumatra (M8.5) Dec. 26,2004. Previous analysis of earthquake events has indicated the presence of an IR anomaly, where temperatures increased or did not return to its usual nighttime value. Our procedures analyze nighttime satellite data that records the general condtion of the ground after sunset. We have found from the MODIS instrument data that five days before the Colima earthquake the IR land surface nighttime temperature rose up to +4 degrees C in a 100 km radius around the epicenter. The IR transient field recorded by MODIS in the vicinity of Parkfield, also with a cloud free environment, was around +1 degree C and is significantly smaller than the IR anomaly around the Colima epicenter. Ground surface temperatures near the Parkfield epicenter four days prior to the earthquake show steady increase. However, on the night preceding the quake, a significant drop in relative humidity was indicated, process similar to those register prior to the Colima event. Recent analyses of continuous ongoing long- wavelength Earth radiation (OLR) indicate significant and anomalous variability prior to some earthquakes. The cause of these anomalies is not well understood but could be the result of a triggering by an interaction between the lithosphere-hydrosphere and atmospheric related to changes in the near surface electrical field and/or gas composition prior to the earthquake. The OLR anomaly usually covers large areas surrounding the main epicenter. We have found strong anomalies signal (two sigma) along the epicentral area signals on Dec 21

  16. Study of Banana Dehydration Using Sequential Infrared Radiation and Freeze-Drying

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The drying and quality characteristics of banana slices processed with a sequential infrared radiation and freeze-drying (SIRFD) method were investigated. To study the drying characteristics of bananas during the infrared (IR) and hot air predehydration, Cavendish bananas slices with 5 mm thickness...

  17. Application of power stabilized laser to the uncooled infrared imaging system

    NASA Astrophysics Data System (ADS)

    Liu, Ming; Zhao, Yuejin; Liu, Xiaohua; Dong, Liquan; Teng, Fei

    2008-08-01

    A new new kind of IR imaging system which is based on MEMS microcantilever has come out in recent years. The infrared radiation detection and the subsequent reconstruction of an image are based on the deflection of individual microcantilever pixels. This detection is applied in an optical way, which means there is no electrical contact to each individual pixel. This approach has drawn considerable attention due to the advantages of low cost, light weight, low power consumption, high reliability and no back-ground electrothermal noise. Firstly the incoming IR light is blocked and an image of the microcantilever array is captured by a camera as a background image before an optical readout process. Then the IR light is let in and the difference between the background image and the current image captured is calculated and exported as an IR video signal. This process has a critical demand on light power stability. A CCD of 12 bit resolution is used to achieve a high signal to noise ratio. Its resolution is 4096 which means it can detect a light power changing of 1/4096 or 0.02% theoretically. The instability of common lasers is a few percent and the long time instability of LED light sources can be about 1%. These instabilities are all larger than 1/4096. The power variation can be detected by the CCD if these lasers or LEDs are used as the light source in the system. This power variation will affect the signal to noise ratio of an output IR signal. We have done some experiments in this paper. The laser power stabilizer consists of an electro-optical modulator and an optical feedback system. The peak-to-peak instability of the laser output power reaches within 0.1% in a few minutes. The stabilized laser beam is applied to the optical readout process. The experiment shows that the output IR image is much more stable than before. The drift of light power is almost eliminated. The NETD of the whole system reaches about 2 K.

  18. Infrared Aerosol Radiative Forcing at the Surface and the Top of the Atmosphere

    NASA Technical Reports Server (NTRS)

    Markowicz, Krzysztof M.; Flatau, Piotr J.; Vogelmann, Andrew M.; Quinn, Patricia K.; Welton, Ellsworth J.

    2003-01-01

    We study the clear-sky aerosol radiative forcing at infrared wavelengths using data from the Aerosol Characterization Experiment (ACE-Asia) cruise of the NOAA R/V Ronald H. Brown. Limited number of data points is analyzed mostly from ship and collocated satellite values. An optical model is derived from chemical measurements, lidar profiles, and visible extinction measurements which is used to and estimate the infrared aerosol optical thickness and the single scattering albedo. The IR model results are compared to detailed Fourier Transform Interferometer based infrared aerosol forcing estimates, pyrgeometer based infrared downward fluxes, and against the direct solar forcing observations. This combined approach attests for the self-consistency of the optical model and allows to derive quantities such as the infrared forcing at the top of the atmosphere or the infrared optical thickness. The mean infrared aerosol optical thickness at 10 microns is 0.08 and the single scattering albedo is 0.55. The modeled infrared aerosol forcing reaches 10 W/sq m during the cruise, which is a significant contribution to the total direct aerosol forcing. The surface infrared aerosol radiative forcing is between 10 to 25% of the shortwave aerosol forcing. The infrared aerosol forcing at the top of the atmosphere can go up to 19% of the solar aerosol forcing. We show good agreement between satellite (CERES instrument) retrievals and model results at the top of the atmosphere. Over the Sea of Japan, the average infrared radiative forcing is 4.6 W/sq m in the window region at the surface and it is 1.5 W/sq m at top of the atmosphere. The top of the atmosphere IR forcing efficiency is a strong function of aerosol temperature while the surface IR forcing efficiency varies between 37 and 55 W/sq m (per infrared optical depth unit). and changes between 10 to 18 W/sq m (per infrared optical depth unit).

  19. Quantum optical signatures in strong-field laser physics: Infrared photon counting in high-order-harmonic generation

    PubMed Central

    Gonoskov, I. A.; Tsatrafyllis, N.; Kominis, I. K.; Tzallas, P.

    2016-01-01

    We analytically describe the strong-field light-electron interaction using a quantized coherent laser state with arbitrary photon number. We obtain a light-electron wave function which is a closed-form solution of the time-dependent Schrödinger equation (TDSE). This wave function provides information about the quantum optical features of the interaction not accessible by semi-classical theories. With this approach we can reveal the quantum optical properties of high harmonic generation (HHG) process in gases by measuring the photon statistics of the transmitted infrared (IR) laser radiation. This work can lead to novel experiments in high-resolution spectroscopy in extreme-ultraviolet (XUV) and attosecond science without the need to measure the XUV light, while it can pave the way for the development of intense non-classical light sources. PMID:27601191

  20. Quantum optical signatures in strong-field laser physics: Infrared photon counting in high-order-harmonic generation.

    PubMed

    Gonoskov, I A; Tsatrafyllis, N; Kominis, I K; Tzallas, P

    2016-01-01

    We analytically describe the strong-field light-electron interaction using a quantized coherent laser state with arbitrary photon number. We obtain a light-electron wave function which is a closed-form solution of the time-dependent Schrödinger equation (TDSE). This wave function provides information about the quantum optical features of the interaction not accessible by semi-classical theories. With this approach we can reveal the quantum optical properties of high harmonic generation (HHG) process in gases by measuring the photon statistics of the transmitted infrared (IR) laser radiation. This work can lead to novel experiments in high-resolution spectroscopy in extreme-ultraviolet (XUV) and attosecond science without the need to measure the XUV light, while it can pave the way for the development of intense non-classical light sources. PMID:27601191

  1. Observation of laser driven supercritical radiative shock precursors.

    PubMed

    Bouquet, S; Stéhlé, C; Koenig, M; Chièze, J-P; Benuzzi-Mounaix, A; Batani, D; Leygnac, S; Fleury, X; Merdji, H; Michaut, C; Thais, F; Grandjouan, N; Hall, T; Henry, E; Malka, V; Lafon, J-P J

    2004-06-01

    We present a supercritical radiative shock experiment performed with the LULI nanosecond laser facility. Using targets filled with xenon gas at low pressure, the propagation of a strong shock with a radiative precursor is evidenced. The main measured shock quantities (electronic density and propagation velocity) are shown to be in good agreement with theory and numerical simulations. PMID:15245230

  2. Design challenges for matrix assisted pulsed laser evaporation and infrared resonant laser evaporation equipment

    NASA Astrophysics Data System (ADS)

    Greer, James A.

    2011-11-01

    for several reasons. The first reason is that the polymer/solvent mix as well as the sample holder are both exposed to the humidity in the air which will coat the entire surface of the holder and target with water vapor. Some polymer and/or solvent materials may not react well with water vapor. Also, the layer of water vapor absorbed on the target surface may then absorb the incident laser radiation until it is removed from the surface. Thus, it may be unclear when the water vapor is fully removed from the polymer/solvent surface and the MAPLE deposition process actually occurs. This makes deposition of specific polymer thickness difficult to calculate. While it is well known that Quartz crystal microbalances do not work well for PLD of oxide materials it can be used for the deposition of MAPLE materials. However, with rastered laser beams the tooling factor becomes a dynamic number making interpretation of final thickness potentially difficult without careful pre-calibration. Another serious issue with the initial MAPLE process was related to the use of UV lasers such as an excimer operating at 193- or 248-nm or frequency tripled, Nd:YAG lasers at 355 nm. These lasers have high energy per photon (between about 6.4 to 3.5 eV) which can lead to a variety of deleterious photochemical mechanisms that can damage the polymer chains or organic structure. Such mechanisms can be direct photo-decomposition by photochemical bond breaking and photothermal effects. Alternative lasers, such as a Er:YAG laser operating at 2.9 microns produce photons with energy of ˜0.43 eV. Such longer wavelength lasers have been used for the IR-MAPLE process and may be very useful for future MAPLE systems. A third issue with the initial approach to MAPLE was that the process did not lend itself easily to growing multilayer films. Most standard pulsed laser deposition tools have "multi-target" carousels that allow for easy target changes and multilayer film growth. This is true for sputtering, MBE

  3. Optical measurement of temperature in biological cells under infrared laser light exposure (λ=800 nm)

    NASA Astrophysics Data System (ADS)

    Moreau, David; Lefort, Claire; Leveque, Philippe; O'Connor, Rod P.

    2015-07-01

    Interest in the interaction between laser light and biological samples has gained momentum in recent years, particularly in neurobiology, where there is significant potential to stimulate neurons with infrared laser light. Despite recent reports showing the application of infrared light for neurostimulation, the underlying mechanism is still unknown. The two main hypotheses are based on thermal or electrostatic mechanisms. Here, a novel optical method is presented to make temperature measurements in human neural cells under infrared laser excitation (λ=800nm) using the dye Rhodamine B (RhB). The measurement of temperature is based on the property of RhB, a fluorescent dye whose fluorescence intensity decreases linearly with increases in temperature. We present and detail the setup and measurement procedure that has temporal resolution of few milliseconds, based around a fluorescent live-cell imaging microscope used for cellular microfluorimetry experiments.

  4. Development of models for thermal infrared radiation above and within plant canopies

    NASA Technical Reports Server (NTRS)

    Paw u, Kyaw T.

    1992-01-01

    Any significant angular dependence of the emitted longwave radiation could result in errors in remotely estimated energy budgets or evapotranspiration. Empirical data and thermal infrared radiation models are reviewed in reference to anisotropic emissions from the plant canopy. The biometeorological aspects of linking longwave models with plant canopy energy budgets and micrometeorology are discussed. A new soil plant atmosphere model applied to anisotropic longwave emissions from a canopy is presented. Time variation of thermal infrared emission measurements is discussed.

  5. On the conversion of infrared radiation from fission reactor-based photon engine into parallel beam

    NASA Astrophysics Data System (ADS)

    Gulevich, Andrey V.; Levchenko, Vladislav E.; Loginov, Nicolay I.; Kukharchuk, Oleg F.; Evtodiev, Denis A.; Zrodnikov, Anatoly V.

    2002-01-01

    The efficiency of infrared radiation conversion from photon engine based on fission reactor into parallel photon beam is discussed. Two different ways of doing that are considered. One of them is to use the parabolic mirror to convert of infrared radiation into parallel photon beam. The another one is based on the use of special lattice consisting of numerous light conductors. The experimental facility and some results are described. .

  6. Moisture Diffusivity Characteristics of Rough Rice Under Infrared Radiation Heating

    Technology Transfer Automated Retrieval System (TEKTRAN)

    To design an efficient infrared (IR) dryer for rough rice, it is important to understand the drying behavior of rice grains under infrared heating. The objective of this study was to determine the moisture diffusivity and moisture diffusivity coefficient of rough rice under IR heating and cooling. ...

  7. High field CdS detector for infrared radiation

    NASA Technical Reports Server (NTRS)

    Tyagi, R. C.; Boer, K. W.; Hadley, H. C.; Robertson, J. B.

    1972-01-01

    New and highly sensitive method of detecting infrared irradiation makes possible solid state infrared detector which is more sensitive near room temperature than usual photoconductive low band gap semiconductor devices. Reconfiguration of high field domains in cadmium sulphide crystals provides basis for discovery.

  8. Resonant phenomena in laser-assisted radiative attachment or recombination

    NASA Astrophysics Data System (ADS)

    Zheltukhin, A. N.; Flegel, A. V.; Frolov, M. V.; Manakov, N. L.; Starace, Anthony F.

    2012-04-01

    Resonant enhancements are predicted in cross sections σn for laser-assisted radiative attachment or electron-ion recombination accompanied by absorption of n laser photons. These enhancements occur for incoming electron energies at which the electron can be attached or recombined by emitting μ laser photons followed by emission of a spontaneous photon upon absorbing n + μ laser photons. The close similarity between rescattering plateaus in spectra of resonant attachment/recombination and of high-order harmonic generation is shown based on a general parametrization for σn and on numerical results for e - H attachment.

  9. Radiative shocks on large scale lasers. Preliminary results

    NASA Astrophysics Data System (ADS)

    Leygnac, S.; Bouquet, S.; Stehle, C.; Barroso, P.; Batani, D.; Benuzzi, A.; Cathala, B.; Chièze, J.-P.; Fleury, X.; Grandjouan, N.; Grenier, J.; Hall, T.; Henry, E.; Koenig, M.; Lafon, J. P. J.; Malka, V.; Marchet, B.; Merdji, H.; Michaut, C.; Poles, L.; Thais, F.

    2001-05-01

    Radiative shocks, those structure is strongly influenced by the radiation field, are present in various astrophysical objects (circumstellar envelopes of variable stars, supernovae ...). Their modeling is very difficult and thus will take benefit from experimental informations. This approach is now possible using large scale lasers. Preliminary experiments have been performed with the nanosecond LULI laser at Ecole Polytechnique (France) in 2000. A radiative shock has been obtained in a low pressure xenon cell. The preparation of such experiments and their interpretation is performed using analytical calculations and numerical simulations.

  10. Biological research by optically pumped far infrared lasers

    NASA Astrophysics Data System (ADS)

    Zhengyu, Mi

    1989-05-01

    The FIR breeding for paddy rice, black bean and wheat, the chlorophyll mutation of paddy rice induced by optically pumped FIR laser, etc., are presented. The results of SDS electrophoresis analysis of soluble proteins of Drosophita melanrgaster irradiated by optically pumped FIR laser are described and discussed.

  11. Development of a pump-probe facility combining a far-infrared source with laser-like characteristics and a VUV free electron laser

    NASA Astrophysics Data System (ADS)

    Faatz, B.; Fateev, A. A.; Feldhaus, J.; Krzywinski, J.; Pflueger, J.; Rossbach, J.; Saldin, E. L.; Schneidmiller, E. A.; Yurkov, M. V.

    2001-12-01

    The TESLA Test Facility (TTF) at DESY is a facility producing sub-picosecond electron pulses for the generation of VUV or soft X-ray radiation in a free electron laser (FEL). The same electron pulses would also allow the direct production of high-power coherent radiation by passing the electron beam through an undulator. Intense, coherent far-infrared (FIR) undulator radiation can be produced from electron bunches at wavelengths longer than or equal to the bunch length. The source described in this paper provides, in the wavelength range 50- 300 μm, a train of about 1- 10 ps long radiation pulses, with about 1 mJ of optical energy per pulse radiated into the central cone. The average output power can exceed 50 W. In this conceptual design, we intend to use a conventional electromagnetic undulator with a 60 cm period length and a maximum field of 1.5 T. The FIR source will use the spent electron beam coming from the VUV FEL which allows one to significantly extend the scientific potential of the TTF without interfering with the main option of the TTF FEL operation. The pulses of the coherent FIR radiation are naturally synchronized with the VUV pulses from the main TTF FEL, enabling pump-probe techniques using either the FEL pulse as a pump or the FIR pulse as a probe, or vice versa.

  12. Particle beams in ultrastrong laser fields: direct laser acceleration and radiation reaction effects

    NASA Astrophysics Data System (ADS)

    Salamin, Yousef I.; Li, Jian-Xing; Hatsagortsyan, Karen Z.; Tamburini, Matteo; Di Piazza, Antonino; Keitel, Christoph H.

    2015-03-01

    Several aspects of the interaction of particle beams with ultrastrong laser fields are discussed. Firstly, we consider regimes when radiation reaction is not essential and it is demonstrated that employing chirped laser pulses, significant improvement of the direct acceleration of particles can be achieved. Results from single- and many-particle calculations of the particle acceleration, in vacuum, by plane-wave fields, as well as in tightly-focused laser beams, show that the mean energies and their spreads qualify them for important applications. Secondly, we investigate the effect of radiation reaction in electron-laser-beam interactions. Signatures of the quantum radiation reaction during the interaction of an electron bunch with a focused superstrong ultrashort laser pulse can be observed in a characteristic behavior of the spectral bandwidth, and the angular spread of the nonlinear Compton radiation on the laser pulse duration. Furthermore, it is shown that the radiation reaction effects can be employed to control the electron dynamics via the nonlinear interplay between the Lorentz and radiation reaction forces. In particular, it is shown that an ultrarelativistic electron bunch colliding head- on with a strong bichromatic laser pulse can be deflected in a controllable way, by changing either the relative phase or the relative amplitude between the two frequency components of the bichromatic field.

  13. Laser safety in design of near-infrared scanning LIDARs

    NASA Astrophysics Data System (ADS)

    Zhu, X.; Elgin, D.

    2015-05-01

    3D LIDARs (Light Detection and Ranging) with 1.5μm nanosecond pulse lasers have been increasingly used in different applications. The main reason for their popularity is that these LIDARs have high performance while at the same time can be made eye-safe. Because the laser hazard effect on eyes or skin at this wavelength region (<1.4μm) is mainly from the thermal effect accumulated from many individual pulses over a period of seconds, scanning can effectively reduce the laser beam hazard effect from the LIDARs. Neptec LIDARs have been used in docking to the International Space Station, military helicopter landing and industrial mining applications. We have incorporated the laser safety requirements in the LIDAR design and conducted laser safety analysis for different operational scenarios. While 1.5μm is normally said to be the eye-safe wavelength, in reality a high performance 3D LIDAR needs high pulse energy, small beam size and high pulse repetition frequency (PRF) to achieve long range, high resolution and high density images. The resulting radiant exposure of its stationary beam could be many times higher than the limit for a Class 1 laser device. Without carefully choosing laser and scanning parameters, including field-of-view, scan speed and pattern, a scanning LIDAR can't be eye- or skin-safe based only on its wavelength. This paper discusses the laser safety considerations in the design of eye-safe scanning LIDARs, including laser pulse energy, PRF, beam size and scanning parameters in two basic designs of scanning mechanisms, i.e. galvanometer based scanner and Risley prism based scanner. The laser safety is discussed in terms of device classification, nominal ocular hazard distance (NOHD) and safety glasses optical density (OD).

  14. High power mid-infrared continuous-wave optical parametric oscillator pumped by fiber lasers

    NASA Astrophysics Data System (ADS)

    Xu, Xiaojun; Li, Xiao; Liu, Lei; Shang, Yaping

    2015-02-01

    3~5μm mid-infrared laser has many important applications, such as gas detection, spectral analysis, remote sensing, medical treatment, and also in the military laser radar, infrared countermine, and so on. Optical parametric oscillator (OPO) is an efficient way to generate laser in this wavelength range, which has attracted the eyes of many people. In this paper, the recent development of mid-infrared OPO is overviewed. Meanwhile, detailed introduction on our recent work is given. Maximum idler output power of 34.2W at center wavelength of 3.35μm was obtained, to our knowledge, which is the new power record of the international public reporting for the continue-wave (CW) mid-infrared OPO. It is worth mentioning that the pump source, the quasi single-frequency (SF) narrow line width fiber laser, was also developed by our groups. According to the current status of research, some solutions is proposed in order to achieve higher power, narrower line width, and compact volume mid-infrared OPO in a wide tunable range.

  15. Infrared Imaging of {ital In Vivo} Microvasculature Following Pulsed Laser Irradiation

    SciTech Connect

    Telenkov, S.A.; Milner, T.E.; Smithies, D.J.; Nelson, J.S.; Goodman, D.M.; Tanenbaum, B.S.

    1998-10-01

    Infrared emission images of the chick chorioallantoic membrane (CAM) microvasculature following pulsed laser irradiation were recorded using a high speed infrared focal plane array camera. A three-dimensional tomographic reconstruction algorithm was applied to compute the initial space-dependent temperature increase in discrete CAM blood vessels caused by light absorption. The proposed method may provide consistent estimates of the physical dimensions of subsurface blood vessels and may be useful in understanding a variety of biomedical engineering problems involving laser{endash}tissue interaction. {copyright} {ital 1998 Society of Photo-Optical Instrumentation Engineers.}

  16. DNA repair in bacterial cultures and plasmid DNA exposed to infrared laser for treatment of pain

    NASA Astrophysics Data System (ADS)

    Canuto, K. S.; Sergio, L. P. S.; Marciano, R. S.; Guimarães, O. R.; Polignano, G. A. C.; Geller, M.; Paoli, F.; Fonseca, A. S.

    2013-06-01

    Biostimulation of tissues by low intensity lasers has been described on a photobiological basis and clinical protocols are recommended for treatment of various diseases, but their effects on DNA are controversial. The objective of this work was to evaluate effects of low intensity infrared laser exposure on survival and bacterial filamentation in Escherichia coli cultures, and induction of DNA lesions in bacterial plasmids. In E. coli cultures and plasmids exposed to an infrared laser at fluences used to treat pain, bacterial survival and filamentation and DNA lesions in plasmids were evaluated by electrophoretic profile. Data indicate that the infrared laser (i) increases survival of E. coli wild type in 24 h of stationary growth phase, (ii) induces bacterial filamentation, (iii) does not alter topological forms of plasmids and (iv) does not alter the electrophoretic profile of plasmids incubated with exonuclease III or formamidopyrimidine DNA glycosylase. A low intensity infrared laser at the therapeutic fluences used to treat pain can alter survival of E. coli wild type, induce filamentation in bacterial cells, depending on physiologic conditions and DNA repair, and induce DNA lesions other than single or double DNA strand breaks or alkali-labile sites, which are not targeted by exonuclease III or formamidopyrimidine DNA glycosylase.

  17. Survey Talk--New Laser and Optical RadiationDiagnostics

    SciTech Connect

    Leemans, W.P.

    1998-09-01

    New techniques am reported for electron beam monitoring, that rely either on the analysis of the properties of wiggler radiation (from static magnetic fields as well as from laser "undulators", also referred to as Thomson scattering) or on the non-linear mixing of laser radiation with electron beam radiation. The different techniques reviewed are capable of providing information on femtosecond time scales and micron or even sub-micron spatial scales. The laser undulator is also proposed as a useful tool for non- destructive measurement of high power electron beams. An example is given of measuring electron beam energy and energy spread through spectral filtering of spontaneous wiggler radiation [1]. A novel technique based on fluctuational characteristics of radiation is described, for single shot, nondestructive measurement of the electron beam bunch length [2,3]. Thomson scattering based beam monitoring techniques are discussed which, through analysis of the radiated beam properties, allow non-destructive detailed measurement of transverse and longitudinal distributions of relativistic electron beams [4]. Two new techniques are discussed which rely on non-linear optical mixing of laser radiation with electron bunch emission: differential optical gating (DOG) [5] and electron bunch length measurement in a storage ring based on sum-frequency generation [6].

  18. Upgrade of far-infrared laser-based Faraday rotation measurement on MST

    SciTech Connect

    Ding, W. X.; Brower, D. L.; Bergerson, W. F.; Lin, L.

    2010-10-15

    Recently, the far-infrared (FIR) laser ({lambda}{sub 0}=432 {mu}m) Faraday rotation measurement system on MST has been upgraded. The dc flowing-gas discharge CO{sub 2} pump laser is replaced by a rf-excited, sealed CO{sub 2} laser at 9.27 {mu}m (GEM select 100, Coherent Inc., Santa Clara, CA), which is subdivided equally into three parts to simultaneously pump three FIR cavities. The total infrared pump power is approximately 80 W on the 9R(20) line required to pump the formic acid molecule. Each FIR cavity produces {approx}12 mW, sufficient for 11 simultaneous chord interferometry-polarimetry operations. Three key issues [(1) conservation of circularly polarized wave, (2) colinearity of two probe waves, and (3) stability of intermediate frequencies between lasers] affecting the Faraday rotation measurement have been resolved experimentally.

  19. Studies of fullerene absorption and production using an infrared free-electron laser

    SciTech Connect

    Affatigato, M.; Haglund, R.F.; Ying, Z.C.; Compton, R.N.

    1995-12-31

    Tunable photon sources such as free-electron lasers are potentially valuable tools in spectroscopic studies of fullerenes, a new class of carbon materials with unique cage structures. We have used the infrared free-electron-laser facility at Vanderbilt University to study the infrared absorption of gas-phase fullerene molecules and also to investigate the effects of an infrared laser in the synthesis and crystallization of fullerene materials. In one experiment, fullerene vapor was created in a heat pipe through which the FEL beam was passed; the transmission of the FEL beam relative to a reference detector was measured as a function of wavelength. A large (>10%) absorption of the IR laser was observed when it passed through C{sub 60} vapor at {approximately}800{degrees}C. Due to the broad spectral width of the FEL as well as spectral congestion, no spectral peaks were seen when the laser wavelength was tuned across a T{sub 1u}C{sub 60} IR mode near 7.0 {mu}. However, it is expected that the vibrational features can be resolved experimentally by passing the transmitted beam through a monochromator. In a separate experiment, the FEL beam was focused onto a surface of graphite or graphite/metal mixture target. Various fullerene molecules, including endohedral types, were produced when the soot was recovered from the ablation chamber. The yield of the products was measured to be {approximately}0.4 g/J of the incident laser energy. However, both the yield and the product distribution are virtually, the same as those in experiments using a nanosecond Nd:YAG laser. This suggests that the laser wavelength is not a crucial parameter in making fullerenes by laser ablation. Even when the laser is at resonance with one of the vibrational modes of C{sub 60}, the fullerene production is neither substantially enhanced nor suppressed.

  20. Wavelength scaling of efficient high-order harmonic generation by two-color infrared laser fields

    SciTech Connect

    Lan Pengfei; Takahashi, Eiji J.; Midorikawa, Katsumi

    2010-06-15

    We theoretically investigate and demonstrate a better wavelength scaling of harmonic yield in a two-color infrared field. By mixing a Ti:sapphire assistant field with the infrared driving field, we show that high harmonic generation is enhanced and the harmonic yield scales as {lambda}{sup -3}-{lambda}{sup -4} in the plateau region, which falls more slowly as the increase of the driving laser wavelength {lambda} compared with {lambda}{sup -5}-{lambda}{sup -6} in a one-color infrared field.

  1. Metallic oriented nanowires films for infrared radiation manipulation

    NASA Astrophysics Data System (ADS)

    Larciprete, Maria Cristina; Centini, Marco; Voti, Roberto Li; Bertolotti, Mario; Sibilia, Concita

    2016-04-01

    We developed a numerical method to model the infrared spectral properties of metal nanowires on a flat substrate. Homogenization techniques and the transfer matrix method for birefringent layered materials are merged together so as to obtain a simple but effective tool for tailoring and optimizing the infrared properties of the resulting system. Different in-plane orientations can be investigated, ranging from randomly to perfectly aligned nanowires. Furthermore, the model allows the introduction of an off-plane tilt of the nanowires axes, thus increasing designing options. Possible applications such as broad band infrared polarizers, polarizing beam splitter and polarization rotators are discussed.

  2. The possibilities of applying infrared lasers in otolaryngology

    NASA Astrophysics Data System (ADS)

    Kukwa, Andrzej; Tulibacki, Marek P.; Wojtowicz, Piotr; Oledzka, Iwona; Obarska, Agnieszka

    2003-10-01

    The authors present their many years of experience in the area of laryngological surgery with various types of solid lasers. In our clinical practice we use Nd-YAG, Ho-YAG and Er-YAG surgical lasers. There are many reasons for applying lasers, depending on medical conditions. One of the most frequent cases are the nasal polyps, where surgical treatment is aimed at curing the results. For this type the procedures there was applied Nd-YAG laser, which has shortened the period of treatment and extended the remission. We also use this laser for mucal tissue corrections of the nasal conchs through deep coagulation effect. The above mentioned laser is also useful for the preventative treatment of granulation stenosis by removal of granulation tissue from different sections of the upper way; from the nose to the trachea.Other laser procedures in the nasal area include coagulation of Kisselbach locus, bleeding in Rendu-Osler disease, separating adhesions of the nasal concha from the nasal septum, coagulation of septal bleeding polyps, angiomas of different location, small papillomae of throat and nose, and reduction of hypertrophy nasopharyngeal mucoosa in OSAS patients, and uvolo-palato-pharyngoplasty (UPPP). Neodymium laser is also used for the management of neoplastic diseases in palliative and radical (CA. basocellulare) treatment for the resection of the premalignant changes (papilloma, leukoplakia) and early neoplastic changes of throat and larynx. Keloplasty in the area of larynx and trachea is performed with the use of Ho-YAG laser, with shallow effect, regardless of the density of tissue, enabling coagulation of vascular vessels. It enables non-traumatic resections of bone structures, such as the wall of maxillary sinus, nasal spine, or conchoplasty; the mucal tissue and the frame. Recent clinical tests are examining the possibilities of Er-YAG laser application for crushing calculus in the salivary ducts. Using lasers in laryngology enables their extensive

  3. Interaction of laser radiation with tissue

    NASA Astrophysics Data System (ADS)

    Weber, Heinz P.; Zweig, Adrian D.; Frenz, Martin; Romano, Valerio

    1990-09-01

    The iiin reason to use lasers for cutting tissue is the instant generation of a coagulated zone along the incision walls . This zone acts baertota however if it becone-s too thi it leads to undesired scar forxrtion durir the healing process. The thickness of the coagulated zone is strongly dependent on the details of the cutting rrecbanisrn that itself is determined by the laser and material pararreters. We studied the influence of laser penetration depth intensity and focal geoirtry as well as physical tissue properties on the resultir laser incisions . We iide our investigations on a ndel substance in as well as on freshly excis animal dermis . Laser pulses of 250 p. s duration and 4 Hz repetition rate were eniployed . We corrared incisions made with an laser at 2 . 94 imi to incisions from a laser. We studiI cutting for various focusing conditions . We found that often hydrodynaxnic instabilities developed within the crater and also learned how they can be avoided . The extensions of thermal damage zones depend much stronger on focusing geometry arid intensity than on the optical penetration depth of the cutting beam. Tissue material is eated liquefied and partially ejected during laser cutting. We show that the deree of thermal damage originates from the aimunt of hot material that is not ejected out of the crater of incision. Further we that tissue material is elastically displaced during laser cutting and recoils after cuttir back to exactly its initial position. In soft materials usually the incisions close at the upper end of the hole alnxst instantaneously after termination of the laser pulse . The vacancies left behind are filled with hot water vapor that condenses upon cooling leading to a strong suction process . Thus material from the surface can be pulled into the depth of the incision without being biologically deactivated. 1.

  4. Generation of broadband mid-infrared supercontinuum radiation in cascaded soft-glass fibers

    NASA Astrophysics Data System (ADS)

    Kneis, C.; Robin, T.; Cadier, B.; Brilland, Laurent; Caillaud, Celine; Troles, Johann; Manek-Hönninger, I.; Eichhorn, M.; Kieleck, C.

    2016-03-01

    The generation of mid-infrared (mid-IR) radiation, ranging from 2 - 5 μm, is getting much attention in recent years thanks to many applications it can be used for, e.g. in free space optical communication, range finding, counter measures and remote chemical sensing systems. It also plays an increasing role in medicine, for instance in optical tissue ablation or optical coherence tomography, owing to the high water absorption in that wavelength range. In this research study, a ZrF4-BaF2-LaF3-AlF3-NaF (ZBLAN) fluoride fiber is pumped by a Q-switched mode-locked (QML) thulium (Tm3+)- doped double-clad silica fiber laser, emitting at around 2 μm, to generate mid-IR supercontinuum (SC). Further spectral broadening of this SC radiation is achieved by coupling it into a chalcogenide arsenide-selenide (AsSe) photonic crystal fiber (PCF). An output power of 24 W at 2 μm has been achieved in QML operation for the Tm3+-doped fiber laser. The SC output power from the ZBLAN fiber has been 7.8 W with a spectrum extending to approximately 4.1 μm. For further wavelength broadening experiments, a long-wave-pass filter with a 3 dB edge around 3.6 μm has been implemented between the ZBLAN and the AsSe fiber to cut out the residual pump light at 2 μm and the radiation between 2 μm and 3.5 μm. The pump power was approximately 120 mW with a spectrum from 3.5 μm to 3.9 μm. First proof of principal experiments has been performed with 20 mW of averaged output power and a spectrum extending to 4.9 μm. The coupling efficiency of the SC radiation from the ZBLAN fiber into the AsSe fiber has been around 30%.

  5. Dual-frequency injection-locked continuous-wave near-infrared laser.

    PubMed

    Gavara, Trivikramarao; Ohashi, Takeru; Sasaki, Yusuke; Kawashima, Takuya; Hamano, Hiroaki; Yoshizaki, Ryo; Fujimura, Yuki; Yoshii, Kazumichi; Ohae, Chiaki; Katsuragawa, Masayuki

    2016-07-01

    We report a dual-frequency injection-locked continuous-wave near-infrared laser. The entire system consists of a Ti:sapphire ring laser as a power oscillator, two independent diode lasers employed as seed lasers, and a master cavity providing a frequency reference. Stable dual-frequency injection-locked oscillation is achieved with a maximum output power of 2.8 W. We show its single longitudinal/transverse mode characteristics and practical power stability, as fundamental performance features of this laser system. We also demonstrate arbitrary selectivity of the two frequencies and flexible control of their relative powers by simply manipulating the seed lasers, as advanced features. PMID:27367084

  6. Laser radiography forming bremsstrahlung radiation to image an object

    DOEpatents

    Perry, Michael D.; Sefcik, Joseph A.

    2004-01-13

    A method of imaging an object by generating laser pulses with a short-pulse, high-power laser. When the laser pulse strikes a conductive target, bremsstrahlung radiation is generated such that hard ballistic high-energy electrons are formed to penetrate an object. A detector on the opposite side of the object detects these electrons. Since laser pulses are used to form the hard x-rays, multiple pulses can be used to image an object in motion, such as an exploding or compressing object, by using time gated detectors. Furthermore, the laser pulses can be directed down different tubes using mirrors and filters so that each laser pulse will image a different portion of the object.

  7. Ultraviolet laser beam monitor using radiation responsive crystals

    DOEpatents

    McCann, Michael P.; Chen, Chung H.

    1988-01-01

    An apparatus and method for monitoring an ultraviolet laser beam includes disposing in the path of an ultraviolet laser beam a substantially transparent crystal that will produce a color pattern in response to ultraviolet radiation. The crystal is exposed to the ultraviolet laser beam and a color pattern is produced within the crystal corresponding to the laser beam intensity distribution therein. The crystal is then exposed to visible light, and the color pattern is observed by means of the visible light to determine the characteristics of the laser beam that passed through crystal. In this manner, a perpendicular cross sectional intensity profile and a longitudinal intensity profile of the ultraviolet laser beam may be determined. The observation of the color pattern may be made with forward or back scattered light and may be made with the naked eye or with optical systems such as microscopes and television cameras.

  8. Applications of infrared free electron lasers in picosecond and nonlinear spectroscopy

    NASA Astrophysics Data System (ADS)

    Fann, W. S.; Benson, S. V.; Madey, J. M. J.; Etemad, S.; Baker, G. L.; Rothberg, L.; Roberson, M.; Austin, R. H.

    1990-10-01

    In this paper we describe two different types of spectroscopic experiments that exploit the characteristics of the infrared FEL, Mark III, for studies of condensed matter: - the spectrum of χ(3)(-3ω; ω, ω, ω) in polyacetylene: an application of the free electron laser in nonlinear optical spectroscopy, and - a dynamical test of Davydov-like solitons in acetanilide using a picosecond free electron laser. These two studies highlight the unique contributions FELs can make to condensed-matter spectroscopy.

  9. Low-intensity infrared laser effects on zymosan-induced articular inflammatory response

    NASA Astrophysics Data System (ADS)

    Januária dos Anjos, Lúcia Mara; da Fonseca, Adenilson d. S.; Gameiro, Jacy; de Paoli, Flávia

    2015-03-01

    Low-level therapy laser is a phototherapy treatment that involves the application of low power light in the red or infrared wavelengths in various diseases such as arthritis. In this work, we investigated whether low-intensity infrared laser therapy could cause death by caspase-6 apoptosis or DNA damage pathways in cartilage cells after zymosaninduced articular inflammatory process. Inflammatory process was induced in C57BL/6 mouse by intra-articular injection of zymosan into rear tibio-tarsal joints. Thirty animals were divided in five groups: (I) control, (II) laser, (III) zymosan-induced, (IV) zymosan-induced + laser and (V). Laser exposure was performed after zymosan administration with low-intensity infrared laser (830 nm), power 10 mW, fluence 3.0 J/cm2 at continuous mode emission, in five doses. Twenty-four hours after last irradiation, the animals were sacrificed and the right joints fixed and demineralized. Morphological analysis was observed by hematoxylin and eosin stain, pro-apoptotic (caspase-6) was analyzed by immunocytochemistry and DNA fragmentation was performed by TUNEL assay in articular cartilage cells. Inflammatory process was observed in connective tissue near to articular cartilage, in IV and V groups, indicating zymosan effect. This process was decreased in both groups after laser treatment and dexamethasone. Although groups III and IV presented higher caspase-6 and DNA fragmentation percentages, statistical differences were not observed when compared to groups I and II. Our results suggest that therapies based on low-intensity infrared lasers could reduce inflammatory process and could not cause death by caspase-6 apoptosis or DNA damage pathways in cartilage cells after zymosan-induced articular inflammatory process.

  10. The improved pyroelectric detectors for far-infrared laser interferometer measuring

    NASA Astrophysics Data System (ADS)

    Xiang, Gao

    1990-05-01

    In this paper, the application of the pyroelectric detectors for Far-Infrared laser diagnostics on TOKAMAK plasma is described. We discovered experimentally that the Fabry-Perot interference could affect the performance of the pyroelectric detectors (PED). The improved pyroelectric detector (IPD) was developed for FIR laser coheront measuring. Some designing considerations about the pyroelectric detectors used in high temperature plasma conditions are mentioned.

  11. Infrared laser photolysis - A new tool for the study of prebiotic chemistry

    NASA Technical Reports Server (NTRS)

    Davis, D. D.; Smith, G. R.; Guillory, W. A.

    1980-01-01

    Infrared laser induced dielectric breakdown and multiphoton absorption experiments on CH4/NH3 'atmospheres' are described. It is found that HCN, a central intermediate in prebiotic chemistry, is a principal product. This, combined with the fact that dielectric breakdown appears to have much in common with ordinary electric sparks, suggests that the laser could be a useful tool in studies of prebiotic chemistry. Several possible experiments in this vein are suggested.

  12. DNA fragmentation and nuclear phenotype in tendons exposed to low-intensity infrared laser

    NASA Astrophysics Data System (ADS)

    de Paoli, Flavia; Ramos Cerqueira, Larissa; Martins Ramos, Mayara; Campos, Vera M.; Ferreira-Machado, Samara C.; Geller, Mauro; de Souza da Fonseca, Adenilson

    2015-03-01

    Clinical protocols are recommended in device guidelines outlined for treating many diseases on empirical basis. However, effects of low-intensity infrared lasers at fluences used in clinical protocols on DNA are controversial. Excitation of endogenous chromophores in tissues and free radicals generation could be described as a consequence of laser used. DNA lesions induced by free radicals cause changes in DNA structure, chromatin organization, ploidy degrees and cell death. In this work, we investigated whether low-intensity infrared laser therapy could alter the fibroblasts nuclei characteristics and induce DNA fragmentation. Tendons of Wistar rats were exposed to low-intensity infrared laser (830 nm), at different fluences (1, 5 and 10 J/cm2), in continuous wave (power output of 10mW, power density of 79.6 mW/cm2). Different frequencies were analyzed for the higher fluence (10 J/cm2), at pulsed emission mode (2.5, 250 and 2500 Hz), with the laser source at surface of skin. Geometric, densitometric and textural parameters obtained for Feulgen-stained nuclei by image analysis were used to define nuclear phenotypes. Significant differences were observed on the nuclear phenotype of tendons after exposure to laser, as well as, high cell death percentages was observed for all fluences and frequencies analyzed here, exception 1 J/cm2 fluence. Our results indicate that low-intensity infrared laser can alter geometric, densitometric and textural parameters in tendon fibroblasts nuclei. Laser can also induce DNA fragmentation, chromatin lost and consequently cell death, using fluences, frequencies and emission modes took out from clinical protocols.

  13. Delivery of Erbium:YAG laser radiation through side-firing germanium oxide optical fibers

    NASA Astrophysics Data System (ADS)

    Ngo, Anthony K.; Fried, Nathaniel M.

    2006-02-01

    The Erbium:YAG laser is currently being tested experimentally for endoscopic applications in urology, including more efficient laser lithotripsy and more precise incision of urethral strictures than the Holmium:YAG laser. While side-firing silica fibers are available for use with the Ho:YAG laser in urology, no such fibers exist for use with the Er:YAG laser. These applications may benefit from the availability of a side-firing, mid-infrared optical fiber capable of delivering the laser radiation at a 90-degree angle to the tissue. The objective of this study is to describe the simple construction and characterization of a side-firing germanium oxide fiber for potential use in endoscopic laser surgery. Side-firing fibers were constructed from 450-micron-core germanium oxide fibers of 1.45-m-length by polishing the distal tip at a 45-degree angle and placing a 1-cm-long protective quartz cap over the fiber tip. Er:YAG laser radiation with a wavelength of 2.94 microns, pulse duration of 300 microseconds, pulse repetition rate of 3 Hz, and pulse energies of from 5 to 550 mJ was coupled into the fibers. The fiber transmission rate and damage threshold measured 48 +/- 4 % and 149 +/- 37 mJ, respectively (n = 6 fibers). By comparison, fiber transmission through normal germanium oxide trunk fibers measured 66 +/- 3 %, with no observed damage (n = 5 fibers). Sufficient pulse energies were transmitted through the side-firing fibers for contact tissue ablation. Although these initial tests are promising, further studies will need to be conducted, focusing on assembly of more flexible, smaller diameter fibers, fiber bending transmission tests, long-term fiber reliability tests, and improvement of the fiber output spatial beam profile.

  14. Effective disinfection of rough rice using infrared radiation heating.

    PubMed

    Wang, Bei; Khir, Ragab; Pan, Zhongli; El-Mashad, Hamed; Atungulu, Griffiths G; Ma, Haile; McHugh, Tara H; Qu, Wenjuan; Wu, Bengang

    2014-09-01

    The objective of this study was to investigate the effect of infrared (IR) heating and tempering treatments on disinfection of Aspergillus flavus in freshly harvested rough rice and storage rice. Rice samples with initial moisture contents (IMCs) of 14.1 to 27.0% (wet basis) were infected with A. flavus spores before the tests. The infected samples were heated by IR radiation to 60°C in less than 1 min, and then samples were tempered at 60°C for 5, 10, 20, 30, 60, or 120 min. High heating rates and corresponding high levels of moisture removal were achieved using IR heating. The highest total moisture removal was 5.3% for the fresh rice with an IMC of 27.0% after IR heating and then 120 min of tempering. IR heating followed by tempering for 120 min resulted in 2.5- and 8.3-log reductions of A. flavus spores in rough rice with the lowest and highest IMCs, respectively. To study the effect on disinfection of rewetting dried storage rice, the surface of the dry rice was rewetted to achieve IMCs of 14.7 to 19.4% (wet basis). The rewetting process for the dry rice had a significant effect on disinfection. IR heating followed by tempering for 60 min resulted in 7.2-log reductions in A. flavus on rewetted rough rice. The log-linear plus tail model was applied to estimate the tempering time needed to achieve a 5-log reduction of A. flavus in rice of different IMCs. At least 30 and 20 min of tempering were needed for fresh rice and rewetted rice, respectively, with the highest IMCs. The recommended conditions of simultaneous disinfection and drying for fresh rice was IR heating to 60°C followed by tempering for 120 min and natural cooling, resulting in a final MC of 16.5 to 22.0%, depending on the IMC. For the rewetted dry rice with an IMC of 19.4%, the recommended condition for disinfection and drying involved only 20 min of tempering. The final MC of the sample was 13.8%, which is a safe MC for storage rice. PMID:25198845

  15. Latest Development of Infrared Radiation Heating for Food Processing

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Infrared (IR) heating could be an alternative technology for thermal and dehydration processing of food and agricultural products with many advantages, including high process and energy efficiencies, high product quality, improved food safety and reduced environmental pollution. This paper reviews ...

  16. Eye safety related to near infrared radiation exposure to biometric devices.

    PubMed

    Kourkoumelis, Nikolaos; Tzaphlidou, Margaret

    2011-01-01

    Biometrics has become an emerging field of technology due to its intrinsic security features concerning the identification of individuals by means of measurable biological characteristics. Two of the most promising biometric modalities are iris and retina recognition, which primarily use nonionizing radiation in the infrared region. Illumination of the eye is achieved by infrared light emitting diodes (LEDs). Even if few LED sources are capable of causing direct eye damage as they emit incoherent light, there is a growing concern about the possible use of LED arrays that might pose a potential threat. Exposure to intense coherent infrared radiation has been proven to have significant effects on living tissues. The purpose of this study is to explore the biological effects arising from exposing the eye to near infrared radiation with reference to international legislation. PMID:21380486

  17. Silicone rubber curing by high intensity infrared radiation

    SciTech Connect

    Huang, T.; Tsai, J.; Cherng, C.; Chen, J.

    1994-08-10

    A high-intensity (12 kW) and compact (80 cm) infrared heating oven for fast curing (12 seconds) of tube-like silicone rubber curing studies is reported. Quality inspection by DSC and DMA and results from pilot-scale curing oven all suggest that infrared heating provides a better way of vulcanization regarding to curing time, quality, cost, and spacing over conventional hot air heating. {copyright} {ital 1995} {ital American} {ital Institute} {ital of} {ital Physics}.

  18. LASERS IN MEDICINE: Structure of matrices for the transformation of laser radiation by biofractals

    NASA Astrophysics Data System (ADS)

    Angel'skii, O. V.; Ushenko, A. G.; Arkhelyuk, A. D.; Ermolenko, S. B.; Burkovets, D. N.

    1999-12-01

    The changes in the state of polarisation of laser radiation transformed by biofractal objects are examined. The orientational angular structure of the matrix elements of the operator representing the optical properties of biofractals with different morphological structures (mineralised collagen fibres and myosin bundles) is investigated. An optical model for the description of fractal laser fields under the conditions of single light scattering is proposed.

  19. Results of using low-intensity laser radiation for plumbum intoxication

    NASA Astrophysics Data System (ADS)

    Dejneka, S. Y.

    1999-11-01

    We have studied the noninvasive effect of low-intensive laser impulse radiation in the infrared spectrum region on the liver projection site in experimental lead intoxication achieved by means of intragastric administration of Pb acetate to albino rats over a period of 30 days in a dose of 30 mg/kg. We determined a number of indices in laboratory animals which characterized the state of the nervous system, immune system, muscular performance efficiency. We have also investigated the hematologic indices and the blood and urinary delta-aminolevulinic acid content as well as the plumbum levels in the blood, urine and the animals' inner organs.

  20. Influence of laser radiation on induced absorption spectra of pure quartz glass optical fibers

    NASA Astrophysics Data System (ADS)

    Dianov, Y. M.; Karpechev, V. N.; Korniyenko, L. S.; Rybaltovskiy, A. O.; Chernov, P. V.

    1986-01-01

    The influence of laser radiation on radiation color centers and their associated induced absorption in the spectra of irradiated glass optical fibers is investigated. The glass fiber specimens employed had 40 to 50 micron diameter cores made of day pure quartz glass. The optical fibers were 6 to 20 meters long, produced by chemical precipitation from the gaseous phase and clad with reflecting borosilicate glass. Spectral measurements of the induced absorption in the ultraviolet region were made using an FEU-71 photodetector and a sounding radiation source. The stimulated laser emission power in the cross section of the optical fiber was measured by a photodiode; the absorption spectra were recorded by the fragment method. Eight different types of color centers were isolated whose bands cover practically the entire observed absorption spectra. The connection found between color centers and a 340 nm absorption band, and color center with absorption in the infrared band, indicate that absorption in the ultraviolet band can have a significant influence on the amount of induced absorption in the infrared band.

  1. Design overview of a highly stable infrared free electron laser at LBL

    SciTech Connect

    Kim, K.J.; Berz, M.; Chattopadhyay, S.; Gough, R.; Kim, C.; Kung, A.H.; Xie, M. ); Edighoffer, J. ); Stein, W. )

    1990-11-01

    An infrared free electron laser (IRFEL) is being designed for the Chemical Dynamics Research Laboratory (CDRL) at LBL. The FEL is based on a 50 MeV RF linac operating in synchronization to the Advanced Light Source (ALS), and will produce intense (100 {mu}J per micropulse), narrow bandwidth (narrower than 0.1%) radiation between 3 {mu} and 50 {mu}. In the design, we pay particular attention to the FEL stability issues and require that the fluctuations in electron beam energy and in timing be less then 0.05% and 0.1 ps respectively. The FEL spectrum can then be stabilized to about 10{sup {minus}3}, or if grating is used, to 10{sup {minus}4}. We discuss various sources of fluctuations in the gun, the bunchers and the accelerator sections, as well as the feedback and feedforward schemes to reduce these fluctuations. The accelerator structure is chosen to be of the side coupled, standing wave type for easier control. The beam transport is made isochronous to avoid the coupling between the energy and the timing fluctuations. 12 refs., 1 fig.

  2. Requirements and design of a high stable infrared free electron laser at LBL

    SciTech Connect

    Kim, K.J.; Berz, M.; Chattopadhyay, S.; Gough, R.; Kim, C.; Kung, A.H.; Xie, M. ); Edighoffer, J. ); Stein, W. )

    1990-06-01

    An infrared free electron laser (IRFEL) is being designed for the Chemical Dynamics Research Laboratory (CDRL) at LBL. The FEL is based on a 50 MeV RF linac operating in synchronization to the Advanced Light Source (ALS), and will produce intense (100 {mu}J per micropulse), narrow bandwidth (narrower than 0.1%) radiation between 3 {mu} and 50 {mu}. In the design, we pay particular attention to the FEL stability issues and require that the fluctuations in electron beam energy and in timing be less than 0.05% and 0.1 ps, respectively. The FEL spectrum can then be stabilized to about 10{sup {minus}3}, or if grating is used, to 10{sup {minus}4}. We discuss various sources of fluctuations in the gun, the bunchers and the accelerator sections, as well as the feedback and feedforward schemes to reduce these fluctuations. The accelerator structure is chosen to be of the side coupled, standing wave type for easier control. The beam transport is made isochronous to avoid the coupling between the energy and the timing fluctuations. 9 refs., 2 figs.

  3. Joining titanium materials with tungsten inert gas welding, laser welding, and infrared brazing.

    PubMed

    Wang, R R; Welsch, G E

    1995-11-01

    Titanium has a number of desirable properties for dental applications that include low density, excellent biocompatibility, and corrosion resistance. However, joining titanium is one of the practical problems with the use of titanium prostheses. Dissolved oxygen and hydrogen may cause severe embrittlement in titanium materials. Therefore the conventional dental soldering methods that use oxygen flame or air torch are not indicated for joining titanium materials. This study compared laser, tungsten inert gas, and infrared radiation heating methods for joining both pure titanium and Ti-6Al-4V alloy. Original rods that were not subjected to joining procedures were used as a control method. Mechanical tests and microstructure analysis were used to evaluate joined samples. Mechanical tests included Vickers microhardness and uniaxial tensile testing of the strength of the joints and percentage elongation. Two-way analysis of variance and Duncan's multiple range test were used to compare mean values of tensile strength and elongation for significant differences (p < or = 0.05). Tensile rupture occurred in the joint region of all specimens by cohesive failure. Ti-6Al-4V samples exhibited significantly greater tensile strength than pure titanium samples. Samples prepared by the three joining methods had markedly lower tensile elongation than the control titanium and Ti-6Al-4V rods. The changes in microstructure and microhardness were studied in the heat-affected and unaffected zones. Microhardness values increased in the heat-affected zone for all the specimens tested. PMID:8809260

  4. Effect of transcranial laser infrared irradiation of the mouse brain on analgesic defense-reflex reactions

    NASA Astrophysics Data System (ADS)

    Geinits, A. V.; Avrutskii, M. Y.; Guseinov, T. Y.

    2001-04-01

    An investigation of reflectory analgesic reactions was made on the brain of white mice when it was exposed to transcranial laser radiation with the wavelength of 0.89 micrometers and the energy density of 3.12 J cm-2. These reactions were evaluated with the aid of `tail flick' and `hot plate' tests. It was found that antinociceptive reactions did not change during the experiment. However, laser radiation might produce a protective antistress effect.

  5. Delivery of 3-5 μm laser radiation by a hollow waveguide

    NASA Astrophysics Data System (ADS)

    Němec, M.; Jelínková, H.; Miyagi, M.; Iwai, K.; Doroshenko, M.

    2014-04-01

    Radiation delivery is required for various applications—mainly in medicine or industry. Due to the necessity of delivering IR, UV or powerful radiation, its transfer by hollow waveguides was investigated because standard glass fibers cause serious losses. Our special waveguide was based on a fused silica glass capillary tube with an inner silver layer and dielectric film (cyclic olefin polymer (COP)). Three lasers were designed and constructed as mid-infrared sources, namely Er:YAG (2.94 μm), Dy: PbGa2S4 (4.3 μm) and Fe:ZnSe (4.45 μm). The delivered spatial beam profile and transfer capability of 3-5 μm radiation by the COP/Ag hollow glass waveguide were characterized.

  6. An infrared free-electron laser for the Chemical Dynamics Research Laboratory

    SciTech Connect

    Vaughan, D.

    1992-04-01

    This document describes a free-electron laser (FEL) proposed as part of the Chemical Dynamics Research Laboratory (CDRL), a user facility that also incorporates several advanced lasers of conventional design and two beamlines for the ALS. The FEL itself addresses the needs of the chemical sciences community for a high-brightness, tunable source covering a broad region of the infrared spectrum -- from 3 to 50 {mu}m. All of these sources, together with a variety of sophisticated experimental stations, will be housed in a new building to be located adjacent to the ALS. The radiation sources can be synchronized to permit powerful two-color, pump-probe experiments that will further our fundamental understanding of chemical dynamics at the molecular level, especially those aspects relevant to practical issues in combustion chemistry. The technical approach adopted in this design makes use of superconducting radiofrequency (SCRF) accelerating structures. The primary motivation for adopting this approach was to meet the user requirement for wavelength stability equal to one part in 10{sup 4}. Previous studies concluded that a wavelength stability of only one part in 10{sup 3} could be achieved with currently available room-temperature technology. In addition, the superconducting design operates in a continuous-wave (cw) mode and hence offers considerably higher average optical output power. It also allows for various pulse-gating configurations that will permit simultaneous multiuser operations. A summary of the comparative performance attainable with room-temperature and superconducting designs is given. The FEL described in this report provides a continuous train of 30-ps micropulses, with 100{mu}J of optical energy per micropulse, at a repetition rate of 6.1 MHz. The device can also deliver pulses at a cw repetition rate of 12.2 MHz, with a peak power of 50 {mu}J per micropulse. 70 ref.

  7. An infrared free-electron laser for the Chemical Dynamics Research Laboratory. Design report

    SciTech Connect

    Vaughan, D.

    1992-04-01

    This document describes a free-electron laser (FEL) proposed as part of the Chemical Dynamics Research Laboratory (CDRL), a user facility that also incorporates several advanced lasers of conventional design and two beamlines for the ALS. The FEL itself addresses the needs of the chemical sciences community for a high-brightness, tunable source covering a broad region of the infrared spectrum -- from 3 to 50 {mu}m. All of these sources, together with a variety of sophisticated experimental stations, will be housed in a new building to be located adjacent to the ALS. The radiation sources can be synchronized to permit powerful two-color, pump-probe experiments that will further our fundamental understanding of chemical dynamics at the molecular level, especially those aspects relevant to practical issues in combustion chemistry. The technical approach adopted in this design makes use of superconducting radiofrequency (SCRF) accelerating structures. The primary motivation for adopting this approach was to meet the user requirement for wavelength stability equal to one part in 10{sup 4}. Previous studies concluded that a wavelength stability of only one part in 10{sup 3} could be achieved with currently available room-temperature technology. In addition, the superconducting design operates in a continuous-wave (cw) mode and hence offers considerably higher average optical output power. It also allows for various pulse-gating configurations that will permit simultaneous multiuser operations. A summary of the comparative performance attainable with room-temperature and superconducting designs is given. The FEL described in this report provides a continuous train of 30-ps micropulses, with 100{mu}J of optical energy per micropulse, at a repetition rate of 6.1 MHz. The device can also deliver pulses at a cw repetition rate of 12.2 MHz, with a peak power of 50 {mu}J per micropulse. 70 ref.

  8. Detailed in situ laser calibration of the infrared imaging video bolometer for the JT-60U tokamak

    SciTech Connect

    Parchamy, H.; Peterson, B. J.; Konoshima, S.; Hayashi, H.; Seo, D. C.; Ashikawa, N

    2006-10-15

    The infrared imaging video bolometer (IRVB) in JT-60U includes a single graphite-coated gold foil with an effective area of 9x7 cm{sup 2} and a thickness of 2.5 {mu}m. The thermal images of the foil resulting from the plasma radiation are provided by an IR camera. The calibration technique of the IRVB gives confidence in the absolute levels of the measured values of the plasma radiation. The in situ calibration is carried out in order to obtain local foil properties such as the thermal diffusivity {kappa} and the product of the thermal conductivity k and the thickness t{sub f} of the foil. These quantities are necessary for solving the two-dimensional heat diffusion equation of the foil which is used in the experiments. These parameters are determined by comparing the measured temperature profiles (for kt{sub f}) and their decays (for {kappa}) with the corresponding results of a finite element model using the measured HeNe laser power profile as a known radiation power source. The infrared camera (Indigo/Omega) is calibrated by fitting the temperature rise of a heated plate to the resulting camera data using the Stefan-Boltzmann law.

  9. Temperature stable mid-infrared GaInAsSb/GaSb Vertical Cavity Surface Emitting Lasers (VCSELs).

    PubMed

    Ikyo, A B; Marko, I P; Hild, K; Adams, A R; Arafin, S; Amann, M-C; Sweeney, S J

    2016-01-01

    GaInAsSb/GaSb based quantum well vertical cavity surface emitting lasers (VCSELs) operating in mid-infrared spectral range between 2 and 3 micrometres are of great importance for low cost gas monitoring applications. This paper discusses the efficiency and temperature sensitivity of the VCSELs emitting at 2.6 μm and the processes that must be controlled to provide temperature stable operation. We show that non-radiative Auger recombination dominates the threshold current and limits the device performance at room temperature. Critically, we demonstrate that the combined influence of non-radiative recombination and gain peak-cavity mode de-tuning determines the overall temperature sensitivity of the VCSELs. The results show that improved temperature stable operation around room temperature can only be achieved with a larger gain peak-cavity mode de-tuning, offsetting the significant effect of increasing non-radiative recombination with increasing temperature, a physical effect which must be accounted for in mid-infrared VCSEL design. PMID:26781492

  10. Temperature stable mid-infrared GaInAsSb/GaSb Vertical Cavity Surface Emitting Lasers (VCSELs)

    PubMed Central

    Ikyo, A. B.; Marko, I. P.; Hild, K.; Adams, A. R.; Arafin, S.; Amann, M.-C.; Sweeney, S. J.

    2016-01-01

    GaInAsSb/GaSb based quantum well vertical cavity surface emitting lasers (VCSELs) operating in mid-infrared spectral range between 2 and 3 micrometres are of great importance for low cost gas monitoring applications. This paper discusses the efficiency and temperature sensitivity of the VCSELs emitting at 2.6 μm and the processes that must be controlled to provide temperature stable operation. We show that non-radiative Auger recombination dominates the threshold current and limits the device performance at room temperature. Critically, we demonstrate that the combined influence of non-radiative recombination and gain peak – cavity mode de-tuning determines the overall temperature sensitivity of the VCSELs. The results show that improved temperature stable operation around room temperature can only be achieved with a larger gain peak – cavity mode de-tuning, offsetting the significant effect of increasing non-radiative recombination with increasing temperature, a physical effect which must be accounted for in mid-infrared VCSEL design. PMID:26781492

  11. Temperature stable mid-infrared GaInAsSb/GaSb Vertical Cavity Surface Emitting Lasers (VCSELs)

    NASA Astrophysics Data System (ADS)

    Ikyo, A. B.; Marko, I. P.; Hild, K.; Adams, A. R.; Arafin, S.; Amann, M.-C.; Sweeney, S. J.

    2016-01-01

    GaInAsSb/GaSb based quantum well vertical cavity surface emitting lasers (VCSELs) operating in mid-infrared spectral range between 2 and 3 micrometres are of great importance for low cost gas monitoring applications. This paper discusses the efficiency and temperature sensitivity of the VCSELs emitting at 2.6 μm and the processes that must be controlled to provide temperature stable operation. We show that non-radiative Auger recombination dominates the threshold current and limits the device performance at room temperature. Critically, we demonstrate that the combined influence of non-radiative recombination and gain peak - cavity mode de-tuning determines the overall temperature sensitivity of the VCSELs. The results show that improved temperature stable operation around room temperature can only be achieved with a larger gain peak - cavity mode de-tuning, offsetting the significant effect of increasing non-radiative recombination with increasing temperature, a physical effect which must be accounted for in mid-infrared VCSEL design.

  12. Study on the activation of styrene-based shape memory polymer by medium-infrared laser light

    SciTech Connect

    Leng Jinsong; Yu Kai; Lan Xin; Zhang Dawei; Liu Yanju

    2010-03-15

    This paper demonstrates the feasibility of shape memory polymer (SMP) activation by medium-infrared laser light. Medium-infrared light is transmitted by an optical fiber embedded in the SMP matrix, and the shape recovery process and temperature distribution are recorded by an infrared camera. Light-induced SMP exhibits potential applications in biomedicines and flexible displays.

  13. Development of a mid-infrared laser for study of infrared countermeasures techniques

    NASA Astrophysics Data System (ADS)

    Bekman, H. H. P. T.; van den Heuvel, J. C.; van Putten, F. J. M.; Schleijpen, Ric

    2004-12-01

    Countermeasures against heat seeking missiles require access to efficient laser sources, which should emit wavelengths at band I, II and IV. Efficient diode pumped solid-state lasers, combined with efficient non-linear wavelength shifters, allow the development of practical tuneable mid-IR countermeasure sources. The paper describes the requirements and the development of a tabletop laser source for study of DIRCM techniques. Jamming laser systems must be able of creating pulse sequences in the frequency range between 100 Hz and 10,000 Hz, including the capability to mix and sweep the jam frequency. A Nd:YVO4 pump laser with maximum pump power of 3 Watt and pulse length of 10 ns, and a maximum modulation frequency of 100 kHz was selected. A linear single resonant OPO cavity with 30 mm long, 1mm thick PPLN crystals was build. With the tabletop laser system we were able to generate wavelengths from 1.5 to 4 micron. In band I, at 2 micron we can generate between 400-550 mW, and in band II, from 3-4 micron we can generate 130-160 mW laser jam power. The beam quality (M2) is approximately 2.5. The power efficiency for the idler was 8.8%, while the slope power efficiency was 15%. Jam patterns are generated by use of an acousto-optic modulator.

  14. Study of Banana Dehydration using Sequential Infrared Radiation Heating and Freeze-Drying

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The drying and quality characteristics of banana slices processed with a sequential infrared radiation and freeze drying (SIRFD) method were investigated. Cavendish banana slices with 5 mm thickness were predehydrated using IR heating at each one of three radiation intensities, 3000, 4000, and 5000...

  15. Near-field imaging and nano-Fourier-transform infrared spectroscopy using broadband synchrotron radiation.

    PubMed

    Hermann, Peter; Hoehl, Arne; Patoka, Piotr; Huth, Florian; Rühl, Eckart; Ulm, Gerhard

    2013-02-11

    We demonstrate scanning near-field optical microscopy with a spatial resolution below 100 nm by using low intensity broadband synchrotron radiation in the IR regime. The use of such a broadband radiation source opens up the possibility to perform nano-Fourier-transform infrared spectroscopy over a wide spectral range. PMID:23481749

  16. Coherent-Radiation Spectroscopy of Few-Femtosecond Electron Bunches Using a Middle-Infrared Prism Spectrometer

    NASA Astrophysics Data System (ADS)

    Maxwell, T. J.; Behrens, C.; Ding, Y.; Fisher, A. S.; Frisch, J.; Huang, Z.; Loos, H.

    2013-11-01

    Modern, high-brightness electron beams such as those from plasma wakefield accelerators and free-electron laser linacs continue the drive to ever-shorter bunch durations. In low-charge operation (˜20pC), bunches shorter than 10 fs are reported at the Linac Coherent Light Source (LCLS). Though suffering from a loss of phase information, spectral diagnostics remain appealing as compact, low-cost bunch duration monitors suitable for deployment in beam dynamics studies and operations instrumentation. Progress in middle-infrared (MIR) imaging has led to the development of a single-shot, MIR prism spectrometer to characterize the corresponding LCLS coherent beam radiation power spectrum for few-femtosecond scale bunch length monitoring. In this Letter, we report on the spectrometer installation as well as the temporal reconstruction of 3 to 60 fs-long LCLS electron bunch profiles using single-shot coherent transition radiation spectra.

  17. Multi-spectral imaging with mid-infrared semiconductor lasers

    NASA Astrophysics Data System (ADS)

    Wang, Yi; Wang, Yang; Le, Han Q.

    2006-01-01

    Multi-spectral laser imaging can be a useful technology for target discrimination, classification, and identification based on object spectral signatures. The mid-IR region (~3-14 μm) is particularly rich of molecular spectroscopic fingerprints, but the technology has been under utilized. Compact, potentially inexpensive semiconductor lasers may allow more cost-effective applications. This paper describes a development of semiconductor-laser-based multi-spectral imaging for both near-IR and mid-IR, and demonstrates the potential of this technology. The near-IR study employed 7 wavelengths from 0.635-1.55 μm, and used for system engineering evaluation as well as for studying the fundamental aspects of multi-spectral laser imaging. These include issues of wavelength-dependence scattering as a function of incident and receiving angle and the polarization effects. Stokes vector imaging and degree-of-linear-polarization were shown to reveal significant information to characterize the targets. The mid-IR study employed 4 wavelengths from 3.3-9.6 μm, and was applied to diverse targets that consist of natural and man-made materials and household objects. It was shown capable to resolve and distinguish small spectral differences among various targets, thanks to the laser radiometric and spectral accuracy. Colorless objects in the visible were shown with "colorful" signatures in the mid-IR. An essential feature of the study is an advanced system architecture that employs wavelength-division-multiplexed laser beams for high spectral fidelity and resolution. In addition, unlike conventional one-transmitter and one receiver design, the system is based on a scalable CDMA network concept with multiple transmitters and receivers to allow efficient information acquisition. The results suggest that multi-spectral laser imaging in general can be a unique and powerful technology for wide ranging applications.

  18. Impact of Laser Radiation on Microhardness of a Semiconductor

    SciTech Connect

    Medvid', A.; Onufrijevs, P.; Chiradze, G.; Muktupavela, F.

    2011-12-23

    It was found that strongly absorbed Nd:YAG laser radiation leads to a non-monotonous dependence of microhardness of p- and n-type Si crystals on laser radiation. This dependence is characterized by two maxima for p-Si and one maximum for n-Si crystals. In both cases the increase of microhardness at higher laser intensity is explained by formation of mechanically compressed layer at the irradiated surface due to concentration of the interstitial atoms of Si at the surface in temperature gradient field. The decrease of the microhardness is explained by formation of nano-cones as a result of plastic deformation of the mechanically stressed layer. The additional maximum at lower laser intensity for p-Si crystal is explained by p-n type inversion of Si conductivity.

  19. Fiber based infrared lasers and their applications in medicine, spectroscopy and metrology

    NASA Astrophysics Data System (ADS)

    Alexander, Vinay Varkey

    In my thesis, I have demonstrated the development of fiber based infrared lasers and devices for applications in medicine, spectroscopy and metrology. One of the key accomplishments presented in this thesis for medical applications is the demonstration of a focused infrared laser to perform renal denervation both in vivo and in vitro. Hypertension is a significant health hazard in the US and throughout the world, and the laser based renal denervation procedure may be a potential treatment for resistant hypertension. Compared to current treatment modalities, lasers may be able to perform treatments with lesser collateral tissue damage and quicker treatment times helping to reduce patient discomfort and pain. An additional medical application demonstrated in this thesis is the use of infrared fiber lasers to damage sebaceous glands in human skin as a potential treatment for acne. Another significant work presented in this thesis is a field trial performed at the Wright Patterson Air Force Base using a Short Wave Infrared (SWIR) Supercontinuum (SC) laser as an active illumination source for long distance reflectance measurements. In this case, an SC laser developed as part of this thesis is kept on a 12 story tower and propagated through the atmosphere to a target kept 1.6 km away and used to perform spectroscopy measurements. In the future this technology may permit 24/7 surveillance based on looking for the spectral signatures of materials. Beyond applications in defense, this technology may have far reaching commercial applications as well, including areas such as oil and natural resources exploration. Beyond these major contributions to the state-of-the-art, this thesis also describes other significant studies such as power scalability of SWIR SC sources and non-invasive measurement of surface roughness.

  20. Simulation of free-electron lasers seeded with broadband radiation

    SciTech Connect

    Bajlekov, Svetoslav; Fawley, William; Schroeder, Carl; Bartolini, Riccardo; Hooker, Simon

    2011-03-10

    The longitudinal coherence of free-electron laser (FEL) radiation can be enhanced by seeding the FEL with high harmonics of an optical laser pulse. The radiation produced by high-harmonic generation (HHG), however, has a fast-varying temporal profile that can violate the slowly varying envelope approximation and limited frequency window that is employed in conventional free-electron laser simulation codes. Here we investigate the implications of violating this approximation on the accuracy of simulations. On the basis of both analytical considerations and 1D numerical studies, it is concluded that, for most realistic scenarios, conventional FEL codes are capable of accurately simulating the FEL process even when the seed radiation violates the slowly varying envelope approximation. We additionally discuss the significance of filtering the harmonic content of broadband HHG seeds.

  1. Absorption coefficients of a hydrogen plasma for laser radiation

    NASA Technical Reports Server (NTRS)

    Stallcop, J. R.

    1974-01-01

    The formalism for the calculation of the absorption of radiation by a hydrogen plasma at common laboratory conditions is summarized. The hydrogen plasma absorption coefficient for laser radiation has been computed for a wide range of electron densities and temperatures (10,000-40,000 K). The results of this computation are presented in a graphical form that permits a determination of the absorption coefficient for the following laser wavelengths: 0.176, 0.325, 0.337, 0.442, 0.488, 0.515, 0.633, 0.694, 1.06, 1.15, 2.36, 3.39, 5.40 and 10.6 microns. The application of these results and laser radiation absorption measurements to plasma diagnostics is discussed briefly.

  2. Mechanism of oxidative stress generation in cells by localized near-infrared femtosecond laser excitation

    NASA Astrophysics Data System (ADS)

    He, Hao; Chan, Kam Tai; Kong, Siu Kai; Lee, Rebecca Kit Ying

    2009-12-01

    We examined the effect of femtosecond (fs) and continuous wave (CW) lasers at near-infrared range on the creation of reactive oxygen species in a human liver cancer cell line. By controlling the mitochondria electron transport chain (ETC), it was found that a major part of the oxidative stress was generated by the laser induced thermal effect on the mitochondria while the remaining part was created by direct free electron liberation by the fs pulses, which could be observed after breaking the ETC. The study helps clarify the major effects produced on animal cells when excited by fs lasers.

  3. Use alone or in Combination of Red and Infrared Laser in Skin Wounds

    PubMed Central

    de Lima, Fernando José Camello; Barbosa, Fabiano Timbó; de Sousa-Rodrigues, Célio Fernando

    2014-01-01

    A systematic review was conducted covering the action of red laser, infrared and combination of both, with emphasis on cutaneous wound therapy, showing the different settings on parameters such as fluency, power, energy density, time of application, frequency mode and even the type of low-power lasers and their wavelengths. It was observed that in general, the lasers brings good clinical and histological results mainly, but there is not a protocol that defines a dosage of use that has predictability of therapeutic success in repairing these wounds. PMID:25653799

  4. Three-dimensional direct cell patterning in collagen hydrogels with near-infrared femtosecond laser

    PubMed Central

    Hribar, Kolin C.; Meggs, Kyle; Liu, Justin; Zhu, Wei; Qu, Xin; Chen, Shaochen

    2015-01-01

    We report a methodology for three-dimensional (3D) cell patterning in a hydrogel in situ. Gold nanorods within a cell-encapsulating collagen hydrogel absorb a focused near-infrared femtosecond laser beam, locally denaturing the collagen and forming channels, into which cells migrate, proliferate, and align in 3D. Importantly, pattern resolution is tunable based on writing speed and laser power, and high cell viability (>90%) is achieved using higher writing speeds and lower laser intensities. Overall, this patterning technique presents a flexible direct-write method that is applicable in tissue engineering systems where 3D alignment is critical (such as vascular, neural, cardiac, and muscle tissue). PMID:26603915

  5. Three-dimensional direct cell patterning in collagen hydrogels with near-infrared femtosecond laser

    NASA Astrophysics Data System (ADS)

    Hribar, Kolin C.; Meggs, Kyle; Liu, Justin; Zhu, Wei; Qu, Xin; Chen, Shaochen

    2015-11-01

    We report a methodology for three-dimensional (3D) cell patterning in a hydrogel in situ. Gold nanorods within a cell-encapsulating collagen hydrogel absorb a focused near-infrared femtosecond laser beam, locally denaturing the collagen and forming channels, into which cells migrate, proliferate, and align in 3D. Importantly, pattern resolution is tunable based on writing speed and laser power, and high cell viability (>90%) is achieved using higher writing speeds and lower laser intensities. Overall, this patterning technique presents a flexible direct-write method that is applicable in tissue engineering systems where 3D alignment is critical (such as vascular, neural, cardiac, and muscle tissue).

  6. Cell perforation mediated by plasmonic bubbles generated by a single near infrared femtosecond laser pulse.

    PubMed

    Boutopoulos, Christos; Bergeron, Eric; Meunier, Michel

    2016-01-01

    We report on transient membrane perforation of living cancer cells using plasmonic gold nanoparticles (AuNPs) enhanced single near infrared (NIR) femtosecond (fs) laser pulse. Under optimized laser energy fluence, single pulse treatment (τ = 45 fs, λ = 800 nm) resulted in 77% cell perforation efficiency and 90% cell viability. Using dark field and ultrafast imaging, we demonstrated that the generation of submicron bubbles around the AuNPs is the necessary condition for the cell membrane perforation. AuNP clustering increased drastically the bubble generation efficiency, thus enabling an effective laser treatment using low energy dose in the NIR optical therapeutical window. PMID:26199220

  7. Wavelength-tuneable liquid crystal lasers from the visible to the near-infrared

    NASA Astrophysics Data System (ADS)

    Hands, P. J. W.; Dobson, C. A.; Morris, S. M.; Qasim, M. M.; Gardiner, D. J.; Wilkinson, T. D.; Coles, H. J.

    2011-10-01

    The study of band-edge lasing from dye-doped chiral nematic liquid crystals has thus far been largely restricted to visible wavelengths. In this paper, a wide range of commercially available laser dyes are examined for their suitability as infrared emitters within a chiral nematic host. Problems such as poor solubility and reduced quantum efficiencies are overcome, and successful band-edge lasing is demonstrated within the range of 735-850 nm, using the dyes LD800, HITC-P and DOTC-P. This paper also reports on progress towards widely tuneable liquid crystal lasers, capable of emission in the region 460- 850 nm. Key to this is the use of common pump source, capable of simultaneously exciting all of the dyes (both infrared and visible) that are present within the system. Towards this aim, we successfully demonstrate near-infrared lasing (800 nm) facilitated by Förster energy transfer between the visible dye DCM, and the infra-red dye LD800, enabling pump wavelengths anywhere between 420 and 532 nm to be used. These results demonstrate that small and low-cost tuneable visible to near-infrared laser sources are achievable, using a single common pump source. Such devices are envisaged to have wide-ranging applications including medical imaging (including optical coherence tomography), point-of-care optical medical diagnostics (such as flow cytometry), telecommunications, and optical signatures for security coatings.

  8. Angle-resolved multioctave supercontinua from mid-infrared laser filaments.

    PubMed

    Mitrofanov, A V; Voronin, A A; Sidorov-Biryukov, D A; Mitryukovsky, S I; Rozhko, M V; Pugžlys, A; Fedotov, A B; Panchenko, V Ya; Baltuška, A; Zheltikov, A M

    2016-08-01

    Angle-resolved spectral analysis of a multioctave high-energy supercontinuum output of mid-infrared laser filaments is shown to provide a powerful tool for understanding intricate physical scenarios behind laser-induced filamentation in the mid-infrared. The ellipticity of the mid-infrared driver beam breaks the axial symmetry of filamentation dynamics, offering a probe for a truly (3+1)-dimensional spatiotemporal evolution of mid-IR pulses in the filamentation regime. With optical harmonics up to the 15th order contributing to supercontinuum generation in such filaments alongside Kerr-type and ionization-induced nonlinearities, the output supercontinuum spectra span over five octaves from the mid-ultraviolet deep into the mid-infrared. Full (3+1)-dimensional field evolution analysis is needed for an adequate understanding of this regime of laser filamentation. Supercomputer simulations implementing such analysis articulate the critical importance of angle-resolved measurements for both descriptive and predictive power of filamentation modeling. Strong enhancement of ionization-induced blueshift is shown to offer new approaches in filamentation-assisted pulse compression, enabling the generation of high-power few- and single-cycle pulses in the mid-infrared. PMID:27472598

  9. Near-infrared Single-photon-counting Detectors for Free-space Laser Receivers

    NASA Technical Reports Server (NTRS)

    Krainak, Michael A.; Sun, Xiaoli; Hasselbrack, William; Wu, Stewart; Waczynski, Augustyn; Miko, Laddawan

    2007-01-01

    We compare several photon-counting detector technologies for use as near-infrared timeresolved laser receivers in science instrument, communication and navigation systems. The key technologies are InGaAs(P) photocathode hybrid photomultiplier tubes and InGaAs(P) and HgCdTe avalanche photodiodes. We discuss recent experimental results and application.

  10. The Role And Character Of Resonant States In Photoionization Of Atoms By Strong Infrared Laser Field

    NASA Astrophysics Data System (ADS)

    Vucic, S.; Potvliege, R. M.

    2010-07-01

    The rate of ionization of atomic hydrogen in a strong infrared laser field is calculated in the framework of non-Hermitian Floquet theory. The high dressed excited states responsibles for the resonance enhancements in the photoionization spectrum are large-ao KH states of the high-frequency Floquet theory.

  11. Spectrally narrow mid-infrared optically pumped lasers with partial surface DBR.

    PubMed

    Yang, Chi; Kaspi, Ron; Tilton, Michael L; Chavez, Joseph R; Ongstad, Andrew P; Dente, Gregory C

    2012-05-01

    An optically pumped mid-infrared edge-emitting laser is described, in which a Distributed Bragg Reflector grating partially occupies the surface, and provides spectral narrowing in a high power device. A quasi-continuous-wave power of 3 Watts is obtained at 3.6 µm that is contained within a spectral width of 7 nm. PMID:22565707

  12. Radiation hardness by design for mixed signal infrared readout circuit applications

    NASA Astrophysics Data System (ADS)

    Gaalema, Stephen; Gates, James; Dobyns, David; Pauls, Greg; Wall, Bruce

    2013-09-01

    Readout integrated circuits (ROICs) to support space-based infrared detection applications often have severe radiation tolerance requirements. Radiation hardness-by-design (RHBD) significantly enhances the radiation tolerance of commercially available CMOS and custom radiation hardened fabrication techniques are not required. The combination of application specific design techniques, enclosed gate architecture nFETs and intrinsic thin oxide radiation hardness of 180 nm process node commercial CMOS allows realization of high performance mixed signal circuits. Black Forest Engineering has used RHBD techniques to develop ROICs with integrated A/D conversion that operate over a wide range of temperatures (40K-300K) to support infrared detection. ROIC radiation tolerance capability for 256x256 LWIR area arrays and 1x128 thermopile linear arrays is presented. The use of 130 nm CMOS for future ROIC RHBD applications is discussed.

  13. On focusing of laser radiation with an axicon

    SciTech Connect

    Malyutin, A A

    2011-02-28

    The influence of axially symmetric perturbations of the intensity and phase of the laser beam on its focusing by means of an axicon is considered. It is shown that such perturbations give rise to variations in the radiation energy density on the axicon axis with two periods, {Lambda}/{gamma} and {Lambda}{sup 2}/{lambda}, where {lambda} is the period of perturbation of the laser beam intensity, and {gamma} is the angle of convergence of the focused beam. (imaging)

  14. Highly efficient mid-infrared dysprosium fiber laser.

    PubMed

    Majewski, Matthew R; Jackson, Stuart D

    2016-05-15

    A new, highly efficient and power scalable pump scheme for 3 μm class fiber lasers is presented. Using the free-running 2.8 μm emission from an Er3+-doped fluoride fiber laser to directly excite the upper laser level of the H13/26→H15/26 transition of the Dy3+ ion, output at 3.04 μm was produced with a record slope efficiency of 51%. Using comparatively long lengths of Dy3+-doped fluoride fiber, a maximum emission wavelength of 3.26 μm was measured. PMID:27176955

  15. Infrared A radiation promotes survival of human melanocytes carrying ultraviolet radiation-induced DNA damage.

    PubMed

    Kimeswenger, Susanne; Schwarz, Agatha; Födinger, Dagmar; Müller, Susanne; Pehamberger, Hubert; Schwarz, Thomas; Jantschitsch, Christian

    2016-06-01

    The link between solar radiation and melanoma is still elusive. Although infrared radiation (IR) accounts for over 50% of terrestrial solar energy, its influence on human skin is not well explored. There is increasing evidence that IR influences the expression patterns of several molecules independently of heat. A previous in vivo study revealed that pretreatment with IR might promote the development of UVR-induced non-epithelial skin cancer and possibly of melanoma in mice. To expand on this, the aim of the present study was to evaluate the impact of IR on UVR-induced apoptosis and DNA repair in normal human epidermal melanocytes. The balance between these two effects is a key factor of malignant transformation. Human melanocytes were exposed to physiologic doses of IR and UVR. Compared to cells irradiated with UVR only, simultaneous exposure to IR significantly reduced the apoptotic rate. However, IR did not influence the repair of UVR-induced DNA damage. IR partly reversed the pro-apoptotic effects of UVR via modification of the expression and activity of proteins mainly of the extrinsic apoptotic pathway. In conclusion, IR enhances the survival of melanocytes carrying UVR-induced DNA damage and thereby might contribute to melanomagenesis. PMID:26844814

  16. Infrared glass fiber cables for CO laser medical applications

    NASA Astrophysics Data System (ADS)

    Arai, Tsunenori; Mizuno, Kyoichi; Sensaki, Koji; Kikuchi, Makoto; Watanabe, Tamishige; Utsumi, Atsushi; Takeuchi, Kiyoshi; Akai, Yoshiro

    1993-05-01

    We developed the medical fiber cables which were designed for CO laser therapy, i.e., angioplasty and endoscopic therapy. As-S chalcogenide glass fibers were used for CO laser delivery. A 230 micrometers core-diameter fiber was used for the angioplasty laser cable. The outer diameter of this cable was 600 micrometers . The total length and insertion length of the angioplasty laser cable were 2.5 m and 1.0 m, respectively. Typically, 2.0 W of fiber output was used in the animal experiment in vivo for the ablation of the model plaque which consisted of human atheromatous aorta wall. The transmission of the angioplasty laser cable was approximately 35%, because the reflection loss occurred at both ends of the fiber and window. Meanwhile, the core diameter of the energy delivery fiber for the endoscopic therapy was 450 micrometers . The outer diameter of this cable was 1.7 mm. Approximately 4.5 W of fiber output was used for clinical treatment of pneumothorax through a pneumoscope. Both types of the cables had the ultra-thin thermocouples for temperature monitoring at the tip of the cables. This temperature monitoring was extremely useful to prevent the thermal destruction of the fiber tip. Moreover, the As-S glass fibers were completely sealed by the CaF2 windows and outer tubes. Therefore, these cables were considered to have sufficient safety properties for medical applications. These laser cables were successfully used for the in vivo animal experiments and/or actual clinical therapies.

  17. Advancements in quantum cascade laser-based infrared microscopy of aqueous media.

    PubMed

    Haase, K; Kröger-Lui, N; Pucci, A; Schönhals, A; Petrich, W

    2016-06-23

    The large mid-infrared absorption coefficient of water frequently hampers the rapid, label-free infrared microscopy of biological objects in their natural aqueous environment. However, the high spectral power density of quantum cascade lasers is shifting this limitation such that mid-infrared absorbance images can be acquired in situ within signal-to-noise ratios of up to 100. Even at sample thicknesses well above 50 μm, signal-to-noise ratios above 10 are readily achieved. The quantum cascade laser-based microspectroscopy of aqueous media is exemplified by imaging an aqueous yeast solution and quantifying glucose consumption, ethanol generation as well as the production of carbon dioxide gas during fermentation. PMID:27032367

  18. Bismuth Oxide Thin Films Deposited on Silicon Through Pulsed Laser Ablation, for Infrared Detectors

    NASA Astrophysics Data System (ADS)

    Condurache-Bota, Simona; Constantinescu, Catalin; Tigau, Nicolae; Praisler, Mirela

    2016-12-01

    Infrared detectors are used in many human activities, from industry to military, telecommunications, environmental studies and even medicine. Bismuth oxide thin films have proved their potential for optoelectronic applications, but their uses as infrared sensors have not been thoroughly studied so far. In this paper, pulsed laser ablation of pure bismuth targets within a controlled oxygen atmosphere is proposed for the deposition of bismuth oxide films on Si (100) substrates. Crystalline films were obtained, whose uniformity depends on the deposition conditions (number of laser pulses and the use of a radio-frequency (RF) discharge of the oxygen inside the deposition chamber). The optical analysis proved that the refractive index of the films is higher than 3 and that their optical bandgap is around 1eV, recommending them for infrared applications.

  19. Evaluation of paint coating thickness variations based on pulsed Infrared thermography laser technique

    NASA Astrophysics Data System (ADS)

    Mezghani, S.; Perrin, E.; Vrabie, V.; Bodnar, J. L.; Marthe, J.; Cauwe, B.

    2016-05-01

    In this paper, a pulsed Infrared thermography technique using a homogeneous heat provided by a laser source is used for the non-destructive evaluation of paint coating thickness variations. Firstly, numerical simulations of the thermal response of a paint coated sample are performed. By analyzing the thermal responses as a function of thermal properties and thickness of both coating and substrate layers, optimal excitation parameters of the heating source are determined. Two characteristic parameters were studied with respect to the paint coating layer thickness variations. Results obtained using an experimental test bench based on the pulsed Infrared thermography laser technique are compared with those given by a classical Eddy current technique for paint coating variations from 5 to 130 μm. These results demonstrate the efficiency of this approach and suggest that the pulsed Infrared thermography technique presents good perspectives to characterize the heterogeneity of paint coating on large scale samples with other heating sources.

  20. Nucleotide excision repair pathway assessment in DNA exposed to low-intensity red and infrared lasers

    PubMed Central

    Fonseca, A.S.; Campos, V.M.A.; Magalhães, L.A.G.; Paoli, F.

    2015-01-01

    Low-intensity lasers are used for prevention and management of oral mucositis induced by anticancer therapy, but the effectiveness of treatment depends on the genetic characteristics of affected cells. This study evaluated the survival and induction of filamentation of Escherichia coli cells deficient in the nucleotide excision repair pathway, and the action of T4endonuclease V on plasmid DNA exposed to low-intensity red and near-infrared laser light. Cultures of wild-type (strain AB1157) E. coli and strain AB1886 (deficient in uvrA protein) were exposed to red (660 nm) and infrared (808 nm) lasers at various fluences, powers and emission modes to study bacterial survival and filamentation. Also, plasmid DNA was exposed to laser light to study DNA lesions produced in vitro by T4endonuclease V. Low-intensity lasers:i) had no effect on survival of wild-type E. coli but decreased the survival of uvrA protein-deficient cells,ii) induced bacterial filamentation, iii) did not alter the electrophoretic profile of plasmids in agarose gels, andiv) did not alter the electrophoretic profile of plasmids incubated with T4 endonuclease V. These results increase our understanding of the effects of laser light on cells with various genetic characteristics, such as xeroderma pigmentosum cells deficient in nucleotide excision pathway activity in patients with mucositis treated by low-intensity lasers. PMID:26445337

  1. Nucleotide excision repair pathway assessment in DNA exposed to low-intensity red and infrared lasers.

    PubMed

    Fonseca, A S; Campos, V M A; Magalhães, L A G; Paoli, F

    2015-10-01

    Low-intensity lasers are used for prevention and management of oral mucositis induced by anticancer therapy, but the effectiveness of treatment depends on the genetic characteristics of affected cells. This study evaluated the survival and induction of filamentation of Escherichia coli cells deficient in the nucleotide excision repair pathway, and the action of T4endonuclease V on plasmid DNA exposed to low-intensity red and near-infrared laser light. Cultures of wild-type (strain AB1157) E. coli and strain AB1886 (deficient in uvrA protein) were exposed to red (660 nm) and infrared (808 nm) lasers at various fluences, powers and emission modes to study bacterial survival and filamentation. Also, plasmid DNA was exposed to laser light to study DNA lesions produced in vitro by T4endonuclease V. Low-intensity lasers:i) had no effect on survival of wild-type E. coli but decreased the survival of uvrA protein-deficient cells,ii) induced bacterial filamentation, iii) did not alter the electrophoretic profile of plasmids in agarose gels, andiv) did not alter the electrophoretic profile of plasmids incubated with T4 endonuclease V. These results increase our understanding of the effects of laser light on cells with various genetic characteristics, such as xeroderma pigmentosum cells deficient in nucleotide excision pathway activity in patients with mucositis treated by low-intensity lasers. PMID:26445337

  2. Comparative effectiveness of light emitting diodes (LEDs) and Lasers in near infrared photoimmunotherapy.

    PubMed

    Sato, Kazuhide; Watanabe, Rira; Hanaoka, Hirofumi; Nakajima, Takahito; Choyke, Peter L; Kobayashi, Hisataka

    2016-03-22

    Near infrared photoimmunotherapy (NIR-PIT) is a new cancer treatment that combines the specificity of antibodies for targeting tumors with the toxicity induced by photosensitizers after exposure to near infrared (NIR) light. Herein we compare two NIR-light sources; light emitting diodes (LEDs) and Lasers, for their effectiveness in NIR-PIT. A photosensitizer, IRDye-700DX, conjugated to panitumumab (pan-IR700), was incubated with EGFR-expressing A431 and MDA-MB-468-luc cells. NIR-light was provided by LEDs or Lasers at the same light dose. Laser-light produced more cytotoxicity and greater reductions in IR700-fluorescence intensity than LED-light. Laser-light also produced more cytotoxicity in vivo in both cell lines. Assessment of super-enhanced permeability and retention (SUPR) effects were stronger with Laser than LED. These results suggest that Laser-light produced significantly more cytotoxic effects compared to LEDs. Although LED is less expensive, Laser-light produces superior results in NIR-PIT. PMID:26885688

  3. Comparative effectiveness of light emitting diodes (LEDs) and Lasers in near infrared photoimmunotherapy

    PubMed Central

    Sato, Kazuhide; Watanabe, Rira; Hanaoka, Hirofumi; Nakajima, Takahito; Choyke, Peter L.; Kobayashi, Hisataka

    2016-01-01

    Near infrared photoimmunotherapy (NIR-PIT) is a new cancer treatment that combines the specificity of antibodies for targeting tumors with the toxicity induced by photosensitizers after exposure to near infrared (NIR) light. Herein we compare two NIR-light sources; light emitting diodes (LEDs) and Lasers, for their effectiveness in NIR-PIT. A photosensitizer, IRDye-700DX, conjugated to panitumumab (pan-IR700), was incubated with EGFR-expressing A431 and MDA-MB-468-luc cells. NIR-light was provided by LEDs or Lasers at the same light dose. Laser-light produced more cytotoxicity and greater reductions in IR700-fluorescence intensity than LED-light. Laser-light also produced more cytotoxicity in vivo in both cell lines. Assessment of super-enhanced permeability and retention (SUPR) effects were stronger with Laser than LED. These results suggest that Laser-light produced significantly more cytotoxic effects compared to LEDs. Although LED is less expensive, Laser-light produces superior results in NIR-PIT. PMID:26885688

  4. Combination visible and infrared lasers for skin rejuvenation.

    PubMed

    Lee, Min-Wei Christine

    2002-12-01

    Noninvasive techniques for skin rejuvenation are quickly being established as a new standard in the treatment of mild rhytides and overall skin toning. Multiple laser wavelengths and modalities have been tried for this procedure with varying degrees of success. These lasers include 532 nm, 585 nm, 1064 nm, 1320 nm, 1450 nm, and 1540 nm wavelengths. This study evaluates a combination technique by using a long-pulsed 532 nm potassium titanyl phosphate (KTP) laser and a long-pulsed 1064 nm Neodynium:yttrium aluminum garnet (Nd:YAG) laser, both separately and combined, for noninvasive photorejuvenation and skin toning/collagen enhancement, and establishes efficacy and degree of success. A total of 150 patients were treated with the long-pulsed KTP 532 nm (Aura; Laserscope, San Jose, CA) and long-pulsed Nd:YAG 1064 nm (Lyra; Laserscope) lasers both separately and combined. Patients included skin types I through V. The fluences varied between 7 and 15 J/cm2 at 7 to 20 ms pulse duration with a 2-mm handpiece, and 6 to 15 J/cm2 and 30 to 50 ms with a 4-mm handpiece for KTP. The Nd:YAG fluences were set at 24 to 30 J/cm2 for a 10-mm handpiece and 30 J/cm2 for a SmartScan Plus scanner (Laserscope, San Jose, CA). These energies were delivered at 30 to 65 ms pulse durations. All patients were treated at least 3 times and at most 6 times at monthly intervals, and were observed for up to 18 months after the last treatment. All 150 patients exhibited a mild to moderate degree of improvement in the appearance of rhytides, moderate degree of improvement in skin toning and texture, and great improvement in the reduction of redness and pigmentation. The KTP used alone was superior to the Nd:YAG laser in terms of results. The KTP and Nd:YAG laser combination was superior to either laser used alone. PMID:12512652

  5. Hot spot generation in energetic materials created by long-wavelength infrared radiation

    SciTech Connect

    Chen, Ming-Wei; You, Sizhu; Suslick, Kenneth S.; Dlott, Dana D.

    2014-02-10

    Hot spots produced by long-wavelength infrared (LWIR) radiation in an energetic material, crystalline RDX (1,3,5-trinitroperhydro-1,3,5-triazine), were studied by thermal-imaging microscopy. The LWIR source was a CO{sub 2} laser operating in the 28-30 THz range. Hot spot generation was studied using relatively low intensity (∼100 W cm{sup −2}), long-duration (450 ms) LWIR pulses. The hot spots could be produced repeatedly in individual RDX crystals, to investigate the fundamental mechanisms of hot spot generation by LWIR, since the peak hot-spot temperatures were kept to ∼30 K above ambient. Hot spots were generated preferentially beneath RDX crystal planes making oblique angles with the LWIR beam. Surprisingly, hot spots were more prominent when the LWIR wavelength was tuned to be weakly absorbed (absorption depth ∼30 μm) than when the LWIR wavelength was strongly absorbed (absorption depth ∼5 μm). This unexpected effect was explained using a model that accounts for LWIR refraction and RDX thermal conduction. The weakly absorbed LWIR is slightly focused underneath the oblique crystal planes, and it penetrates the RDX crystals more deeply, increasing the likelihood of irradiating RDX defect inclusions that are able to strongly absorb or internally focus the LWIR beam.

  6. Frequency determination of visible laser light by interferometric comparison with upconverted CO(2) laser radiation.

    PubMed

    Woods, P T; Shotton, K C; Rowley, W R

    1978-04-01

    A servocontrolled 1-m plane-parallel Fabry-Perot interferometer has been developed at NPL for the precise intercomparison of laser wavelengths. This instrument has been used to measure the wavelength ratio of a 679-nm radiation and that from a 633-nm iodine-stabilized He-Ne laser, achieving an accuracy of 2.9 parts in 10(11). The 679-nm light was derived from a stabilized CO(2) laser radiation by upconversion, and the wavelength of this 9.3-microm laser radiation can be calculated from the visible wavelength result. Frequency measurements on the same CO(2) laser radiation have already been made in this laboratory, so that the experiment reported here leads to a precise value for the speed of light in vacuum and to the value of 473, 612, 380.5 +/- 0.3 MHz for the absolute frequency of the visible radiation from a He-Ne laser stabilized to component d of (127)I(2). PMID:20197930

  7. Continuous glucose determination using fiber-based tunable mid-infrared laser spectroscopy

    NASA Astrophysics Data System (ADS)

    Yu, Songlin; Li, Dachao; Chong, Hao; Sun, Changyue; Xu, Kexin

    2014-04-01

    Wavelength-tunable laser spectroscopy in combination with a small-sized fiber-optic attenuated total reflection (ATR) sensor (fiber-based evanescent field analysis, FEFA) is reported for the continuous measurement of the glucose level. We propose a method of controlling and stabilizing the wavelength and power of laser emission and present a newly developed mid-infrared wavelength-tunable laser with a broad emission spectrum band of 9.19-9.77 μm (1024-1088 cm-1). The novel small-sized flow-through fiber-optic ATR sensor with long optical sensing length was used for glucose level determination. The experimental results indicate that the noise-equivalent concentration of this laser measurement system is as low as 3.8 mg/dL, which is among the most precise glucose measurements using mid-infrared spectroscopy. The sensitivity, which is three times that of conventional Fourier transform infrared spectrometer, was acquired because of the higher laser power and higher spectral resolution. The best prediction of the glucose concentration in phosphate buffered saline solution was achieved using the five-variable partial least-squares model, yielding a root-mean-square error of prediction as small as 3.5 mg/dL. The high sensitivity, multiple tunable wavelengths and small fiber-based sensor with long optical sensing length make glucose determination possible in blood or interstitial fluid in vivo.

  8. Cirrus microphysics and infrared radiative transfer: A case study

    NASA Technical Reports Server (NTRS)

    Ackerman, Thomas P.; Heymsfield, Andrew J.; Valero, Francisco P. J.; Kinne, Stefan

    1988-01-01

    Coincident measurements of cirrus cloud microphysical properties such as particle size distribution and particle shape and morphology, and measurements of infrared intensity and flux were made. Data was acquired nearly simultaneously in space and time by a KingAir in cloud and by an ER-2 at an altitude of 19 km. Upwelling infrared intensities and fluxes measured from the ER-2 and observations of cloud particle size distributions and particle phase and morphology made from the KingAir are discussed. Broad-band flux measurements were available both in and below the cirrus layer from the KingAir.

  9. Interaction of repetitively pulsed high energy laser radiation with matter

    NASA Astrophysics Data System (ADS)

    Hugenschmidt, M.

    1986-05-01

    Laser target interaction processes and methods of improving the overall energy balance are discussed. This can be achieved with high repetition rate pulsed lasers even for initially highly reflecting materials, such as metals. Experiments were performed using a pulsed CO2 laser at mean powers up to 2 KW and repetition rates up to 100 Hz. The rates of temperature rise of aluminum for example are increased by more than a factor of 3 as compared to cw-radiation of comparable power density. Similar improvements are found for the overall absorptivities, that are increased by more than an order of magnitude.

  10. Interaction of laser radiation with metal island films

    NASA Astrophysics Data System (ADS)

    Benditskii, A. A.; Viduta, L. V.; Ostranitsa, A. P.; Tomchuk, P. M.; Iakovlev, V. A.

    1986-08-01

    The emission phenomena arising during the interaction of pulsed laser emission with island films are examined with reference to experimental results obtained for island films of gold irradiated by a CO2 laser at a wavelength of 10.6 microns. Well reproducible emission pulses that are also accompanied by light pulses are produced at intensities less than 10 to the 5th W/sq cm, with the film structure remaining unchanged. The maximum energy of the electrons emitted under the effect of laser radiation is estimated at 3 eV; the work function is 2.1 eV.

  11. Picosecond dissociation of amyloid fibrils with infrared laser: A nonequilibrium simulation study

    SciTech Connect

    Hoang Viet, Man; Roland, Christopher Sagui, Celeste; Derreumaux, Philippe; Nguyen, Phuong H.; Li, Mai Suan

    2015-10-21

    Recently, mid-infrared free-electron laser technology has been developed to dissociate amyloid fibrils. Here, we present a theoretical framework for this type of experiment based on laser-induced nonequilibrium all-atom molecular dynamics simulations. We show that the fibril is destroyed due to the strong resonance between its amide I vibrational modes and the laser field. The effects of laser irradiation are determined by a balance between fibril formation and dissociation. While the overall rearrangements of the fibril finish over short time scales, the interaction between the peptides and the solvent continues over much longer times indicating that the waters play an important role in the dissociation process. Our results thus provide new insights into amyloid fibril dissociation by laser techniques and open up new venues to investigate the complex phenomena associated with amyloidogenesis.

  12. Picosecond dissociation of amyloid fibrils with infrared laser: A nonequilibrium simulation study

    NASA Astrophysics Data System (ADS)

    Hoang Viet, Man; Derreumaux, Philippe; Li, Mai Suan; Roland, Christopher; Sagui, Celeste; Nguyen, Phuong H.

    2015-10-01

    Recently, mid-infrared free-electron laser technology has been developed to dissociate amyloid fibrils. Here, we present a theoretical framework for this type of experiment based on laser-induced nonequilibrium all-atom molecular dynamics simulations. We show that the fibril is destroyed due to the strong resonance between its amide I vibrational modes and the laser field. The effects of laser irradiation are determined by a balance between fibril formation and dissociation. While the overall rearrangements of the fibril finish over short time scales, the interaction between the peptides and the solvent continues over much longer times indicating that the waters play an important role in the dissociation process. Our results thus provide new insights into amyloid fibril dissociation by laser techniques and open up new venues to investigate the complex phenomena associated with amyloidogenesis.

  13. Mid-infrared Molecular Emission Studies from Energetic Materials using Laser-Induced Breakdown Spectroscopy

    NASA Astrophysics Data System (ADS)

    Brown, Ei; Hommerich, Uwe; Yang, Clayton; Trivedi, Sudhir; Samuels, Alan; Snyder, Peter

    2011-10-01

    Laser-induced breakdown spectroscopy (LIBS) is a powerful diagnostic tool for detection of trace elements by monitoring the atomic and ionic emission from laser-induced plasmas. The laser-induced plasma was produced by focusing a 30 mJ pulsed Nd:YAG laser (1064 nm) to dissociate, atomize, and ionize target molecules. In this work, LIBS emissions in the mid-infrared (MIR) region were studied for potential applications in chemical, biological, and explosives (CBE) sensing. We report on the observation of MIR emissions from energetic materials (e.g. ammonium compounds) due to laser-induced breakdown processes. All samples showed LIBS-triggered oxygenated breakdown products as well as partially dissociated and recombination molecular species. More detailed results of the performed MIR LIBS studies on the energetic materials will be discussed at the conference.

  14. Monolithic mid-infrared fiber lasers for the 2-4 μm spectral region

    NASA Astrophysics Data System (ADS)

    Fortin, Vincent; Bernier, Martin; Caron, Nicolas; Faucher, Dominic; El-Amraoui, Mohammed; Messaddeq, Younès.; Vallée, Réal

    2013-03-01

    A growing number of applications are calling for compact laser sources operating in the mid-infrared spectral region. A review of our recent work on monolithic fiber lasers based either on the use of rare-earth fluoride fibers or on Raman gain in both fluoride and chalcogenide glass fibers is presented. Accordingly, an erbium-doped double clad fluoride glass all-fiber laser operating in the vicinity of 3 μm is shown. In addition, we present recent results on the first demonstrations of both fluoride and chalcogenide Raman fiber lasers operating at 2.23 μm and 3.34 μm, respectively. It is shown that based on this approach, monolithic fiber lasers could be developed to cover the whole 2-4 μm spectral band.

  15. Radiative cryogenic cooler for the near infrared mapping spectrometer for the Galileo Jupiter Orbiter

    NASA Technical Reports Server (NTRS)

    Cafferty, T. T.

    1981-01-01

    Summaries of the thermal design, analysis, and testing of a radiative cooler for the Near Infrared Mapping Spectrometer (NIMS) for the Galileo Jupiter Orbiter are presented. The radiative cooler rejects approximately 120 milliwatts of heat at a temperature of 75K when operating in the worst-case thermal environment. The cooler is designed to operate against a relatively hostile thermal environment which varies over 145 deg of instrument scan angle and which includes planetary radiation, solar radiation, and emissions from warm spacecraft surfaces (some of which rotate periodically through the radiator field of view).

  16. Germ cell DNA quantification shortly after IR laser radiation.

    PubMed

    Bermúdez, D; Carrasco, F; Diaz, F; Perez-de-Vargas, I

    1991-01-01

    The immediate effect of IR laser radiation on rat germ cells was studied by cytophotometric quantification of the nuclear DNA content in testicular sections. Two different levels of radiation were studied: one according to clinical application (28.05 J/cm2) and another known to increase the germ cell number (46.80 J/cm2). The laser beam induced changes in the germ cell DNA content depending on the cell type, the cell cycle phase and the doses of radiation energy applied. Following irradiation at both doses the percentage of spermatogonia showing a 4c DNA content was increased, while the percentage of these with a 2c DNA content was decreased. Likewise, the percentages of primary spermatocytes with a DNA content equal to 4c (at 28.05 J/cm2), between 2c and 4c (at 46.80 J/cm2) and higher than 4c (at both doses) were increased. No change in the mean spermatid DNA content was observed. Nevertheless, at 46.80 J/cm2 the percentages of elongated spermatids with a c or 2c DNA content differed from the controls. Data show that, even at laser radiation doses used in therapy, the germ cell DNA content is increased shortly after IR laser radiation. PMID:1772145

  17. Design challenges for matrix assisted pulsed laser evaporation and infrared resonant laser evaporation equipment

    NASA Astrophysics Data System (ADS)

    Greer, James A.

    2011-11-01

    for several reasons. The first reason is that the polymer/solvent mix as well as the sample holder are both exposed to the humidity in the air which will coat the entire surface of the holder and target with water vapor. Some polymer and/or solvent materials may not react well with water vapor. Also, the layer of water vapor absorbed on the target surface may then absorb the incident laser radiation until it is removed from the surface. Thus, it may be unclear when the water vapor is fully removed from the polymer/solvent surface and the MAPLE deposition process actually occurs. This makes deposition of specific polymer thickness difficult to calculate. While it is well known that Quartz crystal microbalances do not work well for PLD of oxide materials it can be used for the deposition of MAPLE materials. However, with rastered laser beams the tooling factor becomes a dynamic number making interpretation of final thickness potentially difficult without careful pre-calibration. Another serious issue with the initial MAPLE process was related to the use of UV lasers such as an excimer operating at 193- or 248-nm or frequency tripled, Nd:YAG lasers at 355 nm. These lasers have high energy per photon (between about 6.4 to 3.5 eV) which can lead to a variety of deleterious photochemical mechanisms that can damage the polymer chains or organic structure. Such mechanisms can be direct photo-decomposition by photochemical bond breaking and photothermal effects. Alternative lasers, such as a Er:YAG laser operating at 2.9 microns produce photons with energy of ˜0.43 eV. Such longer wavelength lasers have been used for the IR-MAPLE process and may be very useful for future MAPLE systems. A third issue with the initial approach to MAPLE was that the process did not lend itself easily to growing multilayer films. Most standard pulsed laser deposition tools have "multi-target" carousels that allow for easy target changes and multilayer film growth. This is true for sputtering, MBE

  18. The Laser-assisted photoelectric effect of He, Ne, Ar and Xe in intense extreme ultraviolet and infrared laser fields

    NASA Astrophysics Data System (ADS)

    Hayden, P.; Dardis, J.; Hough, P.; Richardson, V.; Kennedy, E. T.; Costello, J. T.; Düsterer, S.; Redlin, H.; Feldhaus, J.; Li, W. B.; Cubaynes, D.; Meyer, M.

    2016-02-01

    In this paper, we report results on two-colour above-threshold ionisation, where extreme ultraviolet pulses of femtosecond duration were synchronised to intense infrared laser pulses of picosecond duration, in order to study the laser-assisted photoelectric effect of atomic helium, neon, krypton and xenon which leads to the appearance of characteristic sidebands in the photoelectron spectra. The observed trends are found to be well described by a simple model based on the soft-photon approximation, at least for the relatively low optical intensities of up to ? employed in these early experiments.

  19. Blue emission from Eu2+-doped high silica glass by near-infrared femtosecond laser irradiation

    NASA Astrophysics Data System (ADS)

    Qiao, Yanbo; Chen, Danping; Ren, Jinjun; Wu, Botao; Qiu, Jianrong; Akai, Tomoko

    2008-01-01

    Eu2+-doped high silica glass (HSG) is fabricated by sintering porous glass which is impregnated with europium ions. Eu2+-doped HSG is revealed to yield intense blue emission excited by ultraviolet (UV) light and near-infrared femtosecond laser. The emission profile obtained by UV excitation can be well traced by near-infrared femtosecond laser. The upconversion emission excited by 800 nm femtosecond laser is considered to be related to a two-photon absorption process from the relationship between the integrated intensity and the pump power. A tentative scheme of upconverted blue emission from Eu2+-doped HSG was also proposed. The HSG materials presented herein are expected to find applications in high density optical storage and three-dimensional color displays.

  20. Infrared and ultraviolet laser removal of crustose lichens on dolomite heritage stone

    NASA Astrophysics Data System (ADS)

    Sanz, Mikel; Oujja, Mohamed; Ascaso, Carmen; de los Ríos, Asunción; Pérez-Ortega, Sergio; Souza-Egipsy, Virginia; Wierzchos, Jacek; Speranza, Mariela; Cañamares, Maria Vega; Castillejo, Marta

    2015-08-01

    Laser removal of biodeteriogen layers warrants detailed studies due to the advantages it brings with respect to mechanical elimination or the use of biocides. We have investigated elimination of biological crusts on dolomite stones from heritage sites in central Spain. The samples were colonized by epilithic crustose lichens of different species, such as Caloplaca sp. and Verrucaria nigrescens. A comparative study was carried out by applying infrared (1064 nm) and ultraviolet (355 nm) nanosecond laser pulses and sequences pulses of the two wavelengths using a Q-switched Nd:YAG system. To detect anatomical and ultrastructural damage to the lichens, and to assess possible morphological and chemical changes on the underlying stone induced by laser irradiation, we used stereomicroscopy, scanning electron microscopy with backscattered electron imaging and Fourier transform Raman spectroscopy. The optimal conditions for removal of the colonization crust, while ensuring preservation of the lithic substrate, were obtained for dual infrared-ultraviolet sequential irradiation.