Science.gov

Sample records for innovative liquid breeder

  1. Steam generator for liquid metal fast breeder reactor

    DOEpatents

    Gillett, James E.; Garner, Daniel C.; Wineman, Arthur L.; Robey, Robert M.

    1985-01-01

    Improvements in the design of internal components of J-shaped steam generators for liquid metal fast breeder reactors. Complex design improvements have been made to the internals of J-shaped steam generators which improvements are intended to reduce tube vibration, tube jamming, flow problems in the upper portion of the steam generator, manufacturing complexities in tube spacer attachments, thermal stripping potentials and difficulties in the weld fabrication of certain components.

  2. Overview of EU activities on DEMO liquid metal breeder blanket

    SciTech Connect

    Giancarli, L.; Proust, E.

    1994-12-31

    The European test-blanket development programme, started in 1988, is aiming at the selection by 1995 of two DEMO-relevant blanket lines to be tested in ITER. At present, four lines of blanket are under development, two of them using solid and the other two liquid breeder materials. As far as liquid breeders are concerned, two lines of blankets have been selected within the European Union, the water-cooled lithium-lead (the eutectic Pb-17Li) blankets and the dual-coolant Pb-17Li blankets. Designs have been developed considering an agreed set of DEMO specifications, such as, for instance, a fusion power of 2,200 MW, a neutron wall-loading of 2MW/m{sup 2}, a life-time of 20,000 hours, and the use of martensitic steel as a structural material. Moreover, an experimental program has been set up in order to address the main critical issues for each line. The present paper gives an overview of both design and experimental activities within the European Union concerning these two lines of liquid breeder blankets.

  3. Alloys for a liquid metal fast breeder reactor

    DOEpatents

    Rowcliffe, Arthur F.; Bleiberg, Melvin L.; Diamond, Sidney; Bajaj, Ram

    1979-01-01

    An essentially gamma-prime precipitation-hardened iron-chromium-nickel alloy has been designed with emphasis on minimum nickel and chromium contents to reduce the swelling tendencies of these alloys when used in liquid metal fast breeder reactors. The precipitation-hardening components have been designed for phase stability and such residual elements as silicon and boron, also have been selected to minimize swelling. Using the properties of these alloys in one design would result in an increased breeding ratio over 20% cold worked stainless steel, a reference material, of 1.239 to 1.310 and a reduced doubling time from 15.8 to 11.4 years. The gross stoichiometry of the alloying composition comprises from about 0.04% to about 0.06% carbon, from about 0.05% to about 1.0% silicon, up to about 0.1% zirconium, up to about 0.5% vanadium, from about 24% to about 31% nickel, from 8% to about 11% chromium, from about 1.7% to about 3.5% titanium, from about 1.0% to about 1.8% aluminum, from about 0.9% to about 3.7% molybdenum, from about 0.04% to about 0.8% boron, and the balance iron with incidental impurities.

  4. Updated reference design of a liquid metal cooled tandem mirror fusion breeder

    SciTech Connect

    Berwald, D.H.; Whitley, R.H.; Garner, J.K.; Gromada, R.J.; McCarville, T.J.; Moir, R.W.; Lee, J.D.; Bandini, B.R.; Fulton, F.J.; Wong, C.P.C.; Maya, I.; Hoot, C.G.; Schultz, K.R.; Miller, L.G.; Beeston, J.M.; Harris, B.L.; Westman, R.A.; Ghoniem, N.M.; Orient, G.; Wolfer, M.; DeVan, J.H.; Torterelli, P.

    1985-09-01

    Detailed studies of key techinical issues for liquid metal cooled fusion breeder (fusion-fission hybrid blankets) have been performed during the period 1983-4. Based upon the results of these studies, the 1982 reference liquid metal cooled tandem mirror fusion breeder blanket design was updated and is described. The updated reference blankets provides increased breeding and lower technological risk in comparison with the original reference blanket. In addition to the blanket design revisions, a plant concept, cost, and fuel cycle economics assessment is provided. The fusion breeder continues to promise an economical source of fissile fuel for the indefinite future.

  5. Safety and core design of large liquid-metal cooled fast breeder reactors

    NASA Astrophysics Data System (ADS)

    Qvist, Staffan Alexander

    In light of the scientific evidence for changes in the climate caused by greenhouse-gas emissions from human activities, the world is in ever more desperate need of new, inexhaustible, safe and clean primary energy sources. A viable solution to this problem is the widespread adoption of nuclear breeder reactor technology. Innovative breeder reactor concepts using liquid-metal coolants such as sodium or lead will be able to utilize the waste produced by the current light water reactor fuel cycle to power the entire world for several centuries to come. Breed & burn (B&B) type fast reactor cores can unlock the energy potential of readily available fertile material such as depleted uranium without the need for chemical reprocessing. Using B&B technology, nuclear waste generation, uranium mining needs and proliferation concerns can be greatly reduced, and after a transitional period, enrichment facilities may no longer be needed. In this dissertation, new passively operating safety systems for fast reactors cores are presented. New analysis and optimization methods for B&B core design have been developed, along with a comprehensive computer code that couples neutronics, thermal-hydraulics and structural mechanics and enables a completely automated and optimized fast reactor core design process. In addition, an experiment that expands the knowledge-base of corrosion issues of lead-based coolants in nuclear reactors was designed and built. The motivation behind the work presented in this thesis is to help facilitate the widespread adoption of safe and efficient fast reactor technology.

  6. Corrosion-resistant fuel cladding allow for liquid metal fast breeder reactors

    DOEpatents

    Brehm, Jr., William F.; Colburn, Richard P.

    1982-01-01

    An aluminide coating for a fuel cladding tube for LMFBRs (liquid metal fast breeder reactors) such as those using liquid sodium as a heat transfer agent. The coating comprises a mixture of nickel-aluminum intermetallic phases and presents good corrosion resistance to liquid sodium at temperatures up to 700.degree. C. while additionally presenting a barrier to outward diffusion of .sup.54 Mn.

  7. Nuclear Engineering Computer Modules, Thermal-Hydraulics, TH-2: Liquid Metal Fast Breeder Reactors.

    ERIC Educational Resources Information Center

    Reihman, Thomas C.

    This learning module is concerned with the temperature field, the heat transfer rates, and the coolant pressure drop in typical liquid metal fast breeder reactor (LMFBR) fuel assemblies. As in all of the modules of this series, emphasis is placed on developing the theory and demonstrating the use with a simplified model. The heart of the module is…

  8. Measurements of thermal-hydraulic parameters in liquid-metal-cooled fast-breeder reactors

    SciTech Connect

    Sackett, J.I.

    1983-01-01

    This paper discusses instrumentation for liquid-metal-cooled fast breeder reactors (LMFBR's). Included is instrumentation to measure sodium flow, pressure, temperature, acoustic noise, sodium purity, and leakage. The paper identifies the overall instrumentation requirements for LMFBR's and those aspects of instrumentation which are unique or of special concern to LMFBR systems. It also gives an overview of the status of instrument design and performance.

  9. Multiple lead seal assembly for a liquid-metal-cooled fast-breeder nuclear reactor

    DOEpatents

    Hutter, Ernest; Pardini, John A.

    1977-03-15

    A reusable multiple lead seal assembly provides leak-free passage of stainless-steel-clad instrument leads through the cover on the primary tank of a liquid-metal-cooled fast-breeder nuclear reactor. The seal isolates radioactive argon cover gas and sodium vapor within the primary tank from the exterior atmosphere and permits reuse of the assembly and the stainless-steel-clad instrument leads. Leads are placed in flutes in a seal body, and a seal shell is then placed around the seal body. Circumferential channels in the body and inner surface of the shell are contiguous and together form a conduit which intersects each of the flutes, placing them in communication with a port through the wall of the seal shell. Liquid silicone rubber sealant is injected into the flutes through the port and conduit; the sealant fills the space in the flutes not occupied by the leads themselves and dries to a rubbery hardness. A nut, threaded onto a portion of the seal body not covered by the seal shell, jacks the body out of the shell and shears the sealant without damage to the body, shell, or leads. The leads may then be removed from the body. The sheared sealant is cleaned from the body, leads, and shell and the assembly may then be reused with the same or different leads.

  10. Decontamination of liquid-metal fast breeder reactor components for reuse; The French experience

    SciTech Connect

    Michaille, P. ); Moroni, J.C. ); Lambert, I. )

    1991-02-01

    Decontamination of stainless steel liquid-metal fast breeder reactor components for reuse in France began with the decontamination of Rapsodie components. At that time, dilute phosphoric acid was used. To cope with additional irradiated components after Phenix came into operation, an extensive study was performed, which led to the selection of a procedure involving two baths. The first bath, alkaline permanganate (AP), is applied for 3 h; the second bath, sulfo-phosphoric acid (SP), is applied for 6 h, both at 60{degrees}C. Up to three cycles are repeated until the residual dose rate is sufficiently low. Eight intermediate heat exchangers (IHXs) and two primary pumps from Phenix were decontaminated using this method. This paper reports that because SP can pickle only a limited depth ({approximately} 3{mu}m), due to the passivation effect of phosphoric acid, and because of the waste treatment problems associated with phosphates, new solutions were explored. One possibility involves improvement of the AP-SP procedure: In the SPm procedure, the AP bath is omitted and the phosphoric concentration is reduced by a factor of 4. A second approach is the use of a new formula, called SECA, a mixture of maleic and citric acid used in reducing conditions (imposed by hydrazine). Since the Phenix and Superphenix waste treatment facilities are not designed to reprocess maleic-citric acid, only the SPm procedure has been used on reactor components. A low-contaminated IHX from Rapsodie served as a test benchmark, not only for the decontamination procedure, but also for the requalification criteria, before the SPm procedure was applied to a highly contaminated IHX from Phenix. Recent results are presented.

  11. Carbon transport in a bimetallic sodium loop simulating the intermediate heat transport system of a liquid metal fast breeder reactor

    SciTech Connect

    Hampton, L.V.; Spalaris, C.N.; Roy, P.

    1980-04-01

    Carbon transport data from a bimetallic sodium loop simulating the intermediate heat transport system of a Liquid Metal Fast Breeder Reactor are discussed. The results of bulk carbon analyses after 15,000 hours' exposure indicate a pattern of carburization of Type 304 stainless steel foils which is independent of loop sodium temperature. A model based on carbon activity gradients accounting for this behavior is proposed. Data also indicate that carburization of Type 304 stainless steel is a diffusion-controlled process; however, decarburization of the ferritic 2 1/4 Cr-1Mo steel is not. It is proposed that the decarburization of the ferritic steel is controlled by the dissolution of carbides in the steel matrix. The differences in the sodium decarburization behavior of electroslag remelted and vacuum-arc remelted 2 1/4 Cr-1Mo steel are also highlighted.

  12. Theory, design, and operation of liquid metal fast breeder reactors, including operational health physics

    SciTech Connect

    Adams, S.R.

    1985-10-01

    A comprehensive evaluation was conducted of the radiation protection practices and programs at prototype LMFBRs with long operational experience. Installations evaluated were the Fast Flux Test Facility (FFTF), Richland, Washington; Experimental Breeder Reactor II (EBR-II), Idaho Falls, Idaho; Prototype Fast Reactor (PFR) Dounreay, Scotland; Phenix, Marcoule, France; and Kompakte Natriumgekuhlte Kernreak Toranlange (KNK II), Karlsruhe, Federal Republic of Germany. The evaluation included external and internal exposure control, respiratory protection procedures, radiation surveillance practices, radioactive waste management, and engineering controls for confining radiation contamination. The theory, design, and operating experience at LMFBRs is described. Aspects of LMFBR health physics different from the LWR experience in the United States are identified. Suggestions are made for modifications to the NRC Standard Review Plan based on the differences.

  13. The effect of coolant orificing on the core performance of a heterogeneous liquid-metal fast breeder reactor

    SciTech Connect

    Mamoru, K.; Shigehiro, A.; Yoshiaki, O.

    1983-04-01

    The effect of orificing on the core performance of a commercial-size heterogeneous liquid-metal fast breeder reactor was studied analytically. The thermal power output was flattened at beginning of life, and the coolant flow rate was chosen such that the maximum inner cladding temperature of a driver fuel and a blanket fuel was less than or equal to 620/sup 0/C at both beginning of equilibrium life (BOEL) and end of equilibrium life (EOEL). The difference between reactor outlet temperatures at BOEL and EOEL was then calculated for six core configurations: one homogeneous core configuration and five heterogeneous ones. The results showed that the core outlet temperature variation due to the change of the power profile of the radial heterogeneous core configurations is similar to that of the homogeneous one, even when a single type of orificing is used in each core zone, and it will not be necessary to use the more detailed orificing in each zone of a heterogeneous core configuration. The study concludes that for the present design, especially the thermal design, of some heterogeneous core configurations, it is feasible to control the change of the reactor outlet temperature with burnup, even when a single type of orificing is used in each core zone.

  14. Tritium recovery from Li17 sbnd Pb83 liquid breeder by permeation window method

    NASA Astrophysics Data System (ADS)

    Terai, T.; Suzuki, A.; Tanaka, S.

    1997-09-01

    The tritium permeation window method was demonstrated by out-pile deuterium permeation experiments. The deuterium permeation rate was measured at changing parameters such as the chemical composition of purge gas, the fluidity of Li17 sbnd Pb83, the temperature and the condition of surface oxide film to clarify the rate-determining process. The overall mass-transfer coefficient of deuterium from Li17 sbnd Pb83 to purge gas through the Nb wall was smaller by 2-5 orders in magnitude than that determined by deuterium diffusion in Nb. This is not due to deuterium diffusion in Li17 sbnd Pb83 liquid film but due to the formation of niobium oxides on the surface as a permeation barrier. The permeation rate severely decreased with the growth of surface oxide film and it became too small for an actual blanket system. Therefore, it is necessary to protect the Nb surface from oxidation or to use nobler metals instead of Nb.

  15. Fusion breeder

    SciTech Connect

    Moir, R.W.

    1982-04-20

    The fusion breeder is a fusion reactor designed with special blankets to maximize the transmutation by 14 MeV neutrons of uranium-238 to plutonium or thorium to uranium-233 for use as a fuel for fission reactors. Breeding fissile fuels has not been a goal of the US fusion energy program. This paper suggests it is time for a policy change to make the fusion breeder a goal of the US fusion program and the US nuclear energy program. The purpose of this paper is to suggest this policy change be made and tell why it should be made, and to outline specific research and development goals so that the fusion breeder will be developed in time to meet fissile fuel needs.

  16. Evaluation of the Initial Isothermal Physics Measurements at the Fast Flux Test Facility, a Prototypic Liquid Metal Fast Breeder Reactor

    SciTech Connect

    John D. Bess

    2010-03-01

    The Fast Flux Test Facility (FFTF) was a 400-MWt, sodium-cooled, low-pressure, high-temperature, fast-neutron flux, nuclear fission reactor plant designed for the irradiation testing of nuclear reactor fuels and materials for the development of liquid metal fast breeder reactors (LMFBRs). The FFTF was fueled with plutonium-uranium mixed oxide (MOX) and reflected by Inconel-600. Westinghouse Hanford Company operated the FFTF as part of the Hanford Engineering Development Laboratory (HEDL) for the U.S. Department of Energy on the Hanford Site near Richland, Washington. Although the FFTF was a testing facility not specifically designed to breed fuel or produce electricity, it did provide valuable information for LMFBR projects and base technology programs in the areas of plant system and component design, component fabrication, prototype testing, and site construction. The major objectives of the FFTF were to provide a strong, disciplined engineering base for the LMFBR program, provide fast flux testing for other U.S. programs, and contribute to the development of a viable self-sustaining competitive U.S. LMFBR industry. During its ten years of operation, the FFTF acted as a national research facility to test advanced nuclear fuels, materials, components, systems, nuclear power plant operating and maintenance procedures, and active and passive reactor safety technologies; it also produced a large number of isotopes for medical and industrial users, generated tritium for the U.S. fusion research program, and participated in cooperative, international research work. Prior to the implementation of the reactor characterization program, a series of isothermal physics measurements were performed; this acceptance testing program consisted of a series of control rod worths, critical rod positions, subcriticality measurements, maximum reactivity addition rates, shutdown margins, excess reactivity, and isothermal temperature coefficient reactivity. The results of these

  17. Breeder Reactors, Understanding the Atom Series.

    ERIC Educational Resources Information Center

    Mitchell, Walter, III; Turner, Stanley E.

    The theory of breeder reactors in relationship to a discussion of fission is presented. Different kinds of reactors are characterized by the cooling fluids used, such as liquid metal, gas, and molten salt. The historical development of breeder reactors over the past twenty-five years includes specific examples of reactors. The location and a brief…

  18. Preparation of pyrolytic carbon coating on graphite for inhibiting liquid fluoride salt and Xe135 penetration for molten salt breeder reactor

    NASA Astrophysics Data System (ADS)

    Song, Jinliang; Zhao, Yanling; He, Xiujie; Zhang, Baoliang; Xu, Li; He, Zhoutong; Zhang, DongSheng; Gao, Lina; Xia, Huihao; Zhou, Xingtai; Huai, Ping; Bai, Shuo

    2015-01-01

    A fixed-bed deposition method was used to prepare rough laminar pyrolytic carbon coating (RLPyC) on graphite for inhibiting liquid fluoride salt and Xe135 penetration during use in molten salt breeder reactor. The RLPyC coating possessed a graphitization degree of 44% and had good contact with graphite substrate. A high-pressure reactor was constructed to evaluate the molten salt infiltration in the isostatic graphite (IG-110, TOYO TANSO CO., LTD.) and RLPyC coated graphite under 1.01, 1.52, 3.04, 5.07 and 10.13 × 105 Pa for 12 h. Mercury injection and molten-salt infiltration experiments indicated the porosity and the salt-infiltration amount of 18.4% and 13.5 wt% under 1.52 × 105 Pa of IG-110, which was much less than 1.2% and 0.06 wt% under 10.13 × 105 Pa of the RLPyC, respectively. A vacuum device was constructed to evaluate the Xe135 penetration in the graphite. The helium diffusion coefficient of RLPyC coated graphite was 2.16 × 10-12 m2/s, much less than 1.21 × 10-6 m2/s of the graphite. Thermal cycle experiment indicated the coatings possessed excellent thermal stability. The coated graphite could effectively inhibit the liquid fluoride salt and Xe135 penetration.

  19. Coated ceramic breeder materials

    DOEpatents

    Tam, Shiu-Wing; Johnson, Carl E.

    1987-04-07

    A breeder material for use in a breeder blanket of a nuclear reactor is disclosed. The breeder material comprises a core material of lithium containing ceramic particles which has been coated with a neutron multiplier such as Be or BeO, which coating has a higher thermal conductivity than the core material.

  20. Breeder Reprocessing Engineering Test

    SciTech Connect

    Burgess, C.A.; Meacham, S.A.

    1984-01-01

    The Breeder Reprocessing Engineering Test (BRET) is a developmental activity of the US Department of Energy to demonstrate breeder fuel reprocessing technology while closing the fuel cycle for the Fast Flux Test Facility (FFTF). It will be installed in the existing Fuels and Materials Examination Facility (FMEF) at the Hanford Site near Richland, Washington, The major objectives of BRET are: (1) close the US breeder fuel cycle; (2) develop and demonstrate reprocessing technology and systems for breeder fuel; (3) provide an integrated test of breeder reactor fuel cycle technology - rprocessing, safeguards, and waste management. BRET is a joint effort between the Westinghouse Hanford Company and Oak Ridge National Laboratory. 3 references, 2 figures.

  1. Post-scram Liquid Metal cooled Fast Breeder Reactor (LMFBR) heat transport system dynamics and steam generator control: Figures

    NASA Astrophysics Data System (ADS)

    Brukx, J. F. L. M.

    1982-06-01

    Dynamic modeling of LMFBR heat transport system is discussed. Uncontrolled transient behavior of individual components and of the integrated heat transport system are considered. For each component, results showing specific dynamic features of the component and/or model capability were generated. Controlled dynamic behavior for alternative steam generator control systems during forced and natural sodium coolant circulation was analyzed. Combined free and forced convection of laminar and turbulent vertical pipe flow of liquid metals was investigated.

  2. Innovative Strategy on Hydrogen Evolution Reaction Utilizing Activated Liquid Water

    PubMed Central

    Hwang, Bing-Joe; Chen, Hsiao-Chien; Mai, Fu-Der; Tsai, Hui-Yen; Yang, Chih-Ping; Rick, John; Liu, Yu-Chuan

    2015-01-01

    Splitting water for hydrogen production using light, or electrical energy, is the most developed ‘green technique’. For increasing efficiency in hydrogen production, currently, the most exciting and thriving strategies are focused on efficient and inexpensive catalysts. Here, we report an innovative idea for efficient hydrogen evolution reaction (HER) utilizing plasmon-activated liquid water with reduced hydrogen-bonded structure by hot electron transfer. This strategy is effective for all HERs in acidic, basic and neutral systems, photocatalytic system with a g-C3N4 (graphite carbon nitride) electrode, as well as in an inert system with an ITO (indium tin oxide) electrode. Compared to deionized water, the efficiency of HER increases by 48% based on activated water ex situ on a Pt electrode. Increase in energy efficiency from activated water is 18% at a specific current yield of −20 mA in situ on a nanoscale-granulated Au electrode. Moreover, the onset potential of −0.023 V vs RHE was very close to the thermodynamic potential of the HER (0 V). The measured current density at the corresponding overpotential for HER in an acidic system was higher than any data previously reported in the literature. This approach establishes a new vista in clean green energy production. PMID:26541371

  3. Innovative Strategy on Hydrogen Evolution Reaction Utilizing Activated Liquid Water.

    PubMed

    Hwang, Bing-Joe; Chen, Hsiao-Chien; Mai, Fu-Der; Tsai, Hui-Yen; Yang, Chih-Ping; Rick, John; Liu, Yu-Chuan

    2015-01-01

    Splitting water for hydrogen production using light, or electrical energy, is the most developed 'green technique'. For increasing efficiency in hydrogen production, currently, the most exciting and thriving strategies are focused on efficient and inexpensive catalysts. Here, we report an innovative idea for efficient hydrogen evolution reaction (HER) utilizing plasmon-activated liquid water with reduced hydrogen-bonded structure by hot electron transfer. This strategy is effective for all HERs in acidic, basic and neutral systems, photocatalytic system with a g-C3N4 (graphite carbon nitride) electrode, as well as in an inert system with an ITO (indium tin oxide) electrode. Compared to deionized water, the efficiency of HER increases by 48% based on activated water ex situ on a Pt electrode. Increase in energy efficiency from activated water is 18% at a specific current yield of -20 mA in situ on a nanoscale-granulated Au electrode. Moreover, the onset potential of -0.023 V vs RHE was very close to the thermodynamic potential of the HER (0 V). The measured current density at the corresponding overpotential for HER in an acidic system was higher than any data previously reported in the literature. This approach establishes a new vista in clean green energy production. PMID:26541371

  4. Innovative Strategy on Hydrogen Evolution Reaction Utilizing Activated Liquid Water

    NASA Astrophysics Data System (ADS)

    Hwang, Bing-Joe; Chen, Hsiao-Chien; Mai, Fu-Der; Tsai, Hui-Yen; Yang, Chih-Ping; Rick, John; Liu, Yu-Chuan

    2015-11-01

    Splitting water for hydrogen production using light, or electrical energy, is the most developed ‘green technique’. For increasing efficiency in hydrogen production, currently, the most exciting and thriving strategies are focused on efficient and inexpensive catalysts. Here, we report an innovative idea for efficient hydrogen evolution reaction (HER) utilizing plasmon-activated liquid water with reduced hydrogen-bonded structure by hot electron transfer. This strategy is effective for all HERs in acidic, basic and neutral systems, photocatalytic system with a g-C3N4 (graphite carbon nitride) electrode, as well as in an inert system with an ITO (indium tin oxide) electrode. Compared to deionized water, the efficiency of HER increases by 48% based on activated water ex situ on a Pt electrode. Increase in energy efficiency from activated water is 18% at a specific current yield of -20 mA in situ on a nanoscale-granulated Au electrode. Moreover, the onset potential of -0.023 V vs RHE was very close to the thermodynamic potential of the HER (0 V). The measured current density at the corresponding overpotential for HER in an acidic system was higher than any data previously reported in the literature. This approach establishes a new vista in clean green energy production.

  5. Fast Breeder Reactor studies

    SciTech Connect

    Till, C.E.; Chang, Y.I.; Kittel, J.H.; Fauske, H.K.; Lineberry, M.J.; Stevenson, M.G.; Amundson, P.I.; Dance, K.D.

    1980-07-01

    This report is a compilation of Fast Breeder Reactor (FBR) resource documents prepared to provide the technical basis for the US contribution to the International Nuclear Fuel Cycle Evaluation. The eight separate parts deal with the alternative fast breeder reactor fuel cycles in terms of energy demand, resource base, technical potential and current status, safety, proliferation resistance, deployment, and nuclear safeguards. An Annex compares the cost of decommissioning light-water and fast breeder reactors. Separate abstracts are included for each of the parts.

  6. Ceramic breeder materials

    SciTech Connect

    Johnson, C.E.

    1990-01-01

    The breeding blanket is a key component of the fusion reactor because it directly involves tritium breeding and energy extraction, both of which are critical to development of fusion power. The lithium ceramics continue to show promise as candidate breeder materials. This promise was recognized by the International Thermonuclear Reactor (ITER) design team in its selection of ceramics as the first option for the ITER breeder material. Blanket design studies have indicated properties in the candidate materials data base that need further investigation. Current studies are focusing on tritium release behavior at high burnup, changes in thermophysical properties with burnup, compatibility between the ceramic breeder and beryllium multiplier, and phase changes with burnup. Laboratory and in-reactor tests, some as part of an international collaboration for development of ceramic breeder materials, are underway. 32 refs., 1 fig., 1 tab.

  7. Innovations in high-pressure liquid injection technique for gas chromatography: pressurized liquid injection system.

    PubMed

    Luong, Jim; Gras, Ronda; Tymko, Richard

    2003-01-01

    In gas chromatography (GC), highly volatile liquefied hydrocarbons are commonly injected using devices such as high-pressure syringes, piston valves, liquid rotary sampling valves, or vaporizing regulators. Although these techniques are adequate in some cases, there are known deficiencies. A new generation of sampling valve has been recently innovated and commercialized. Some of the highlights of the pressurized liquid injection system (PLIS) include compact size, the capability to directly couple to an injection port without the need for preinjection vaporization and transfer lines, and sample sizes ranging from 0.2 to 2.0 micro L. Although the valve has a specification of helium leak-free rating of 82.7 bar (1200 psig), the valve passes a hydrostatic pressure test of up to 414 bar (6000 psig). In the unheated version of PLIS, vaporization of solutes occur mainly because of the sheering effect of carrier gas in combination with thermal energy drawn from an injection port or a heated adaptor. This was found to be adequate for solutes with high to medium volatility of up to nC14 hydrocarbon. A higher molecular weight range of up to nC44 hydrocarbon can be achieved with the implementation of a heated version of PLIS, in which the channel of the shaft can be resistively heated at a rate of up to 400 degrees C/s. With its first introduction in May 2002, PLIS has gained acceptance amongst practitioners in GC because it addresses a key unarticulated need in sample introduction/enrichment and by specifically targeting many deficiencies encountered in contemporary high-pressure injection devices. In this paper, the design and performance of the various valve systems of PLIS, as well as industrial chromatographic applications, is presented. PMID:14629794

  8. Development of variable-width ribbon heating elements for liquid-metal and gas-cooled fast breeder reactor fuel-pin simulators

    SciTech Connect

    McCulloch, R.W.; Post, D.W.; Lovell, R.T.; Snyder, S.D.

    1981-04-01

    Variable-width ribbon heating elements that provide a chopped-cosine variable heat flux profile have been fabricated for fuel pin simulators used in test loops by the Breeder Reactor Program Thermal-Hydraulic Out-of-Reactor Safety test facility and the Gas-Cooled Fast Breeder Reactor-Core Flow Test Loop. Thermal, mechanical, and electrical design considerations are used to derive an analytical expression that precisely describes ribbon contour in terms of the major fabrication parameters. These parameters are used to generate numerical control tapes that control ribbon cutting and winding machines. Infrared scanning techniques are developed to determine the optimum transient thermal profile of the coils and relate this profile to that generated by the coils in completed fuel pin simulators.

  9. The fusion breeder

    NASA Astrophysics Data System (ADS)

    Moir, Ralph W.

    1982-10-01

    The fusion breeder is a fusion reactor designed with special blankets to maximize the transmutation by 14 MeV neutrons of uranium-238 to plutonium or thorium to uranium-233 for use as a fuel for fission reactors. Breeding fissile fuels has not been a goal of the U.S. fusion energy program. This paper suggests it is time for a policy change to make the fusion breeder a goal of the U.S. fusion program and the U.S. nuclear energy program. There is wide agreement that many approaches will work and will produce fuel for five equal-sized LWRs, and some approach as many as 20 LWRs at electricity costs within 20% of those at today's price of uranium (30/lb of U3O8). The blankets designed to suppress fissioning, called symbiotes, fusion fuel factories, or just fusion breeders, will have safety characteristics more like pure fusion reactors and will support as many as 15 equal power LWRs. The blankets designed to maximize fast fission of fertile material will have safety characteristics more like fission reactors and will support 5 LWRs. This author strongly recommends development of the fission suppressed blanket type, a point of view not agreed upon by everyone. There is, however, wide agreement that, to meet the market price for uranium which would result in LWR electricity within 20% of today's cost with either blanket type, fusion components can cost severalfold more than would be allowed for pure fusion to meet the goal of making electricity alone at 20% over today's fission costs. Also widely agreed is that the critical-path-item for the fusion breeder is fusion development itself; however, development of fusion breeder specific items (blankets, fuel cycle) should be started now in order to have the fusion breeder by the time the rise in uranium prices forces other more costly choices.

  10. Breeder reactors in France

    SciTech Connect

    Zaleski, C.P.

    1980-04-11

    France relies on nuclear power as an important part of her energy program. Anticipating problems with the availability of natural uranium before the year 2020, the French have been pursuing a three-stage program of development of breeder reactors. The third reactor in this program, the near-commercial plant Super Phenix Mark I, is expected to reach power operation in 1983. Although there are still some uncertainties, particularly about the date when the breeder will become competitive with other energy sources, the outlook is considered favorable and preliminary designs for commercial plants are under way.

  11. Innovative methods to stabilize liquid membranes for removal of radionuclides from groundwater

    SciTech Connect

    Lokhandwala, K.

    1997-10-01

    In this Phase I Small Business Innovation Research program, Membrane Technology Research, Inc., is developing a stable liquid membrane for extracting uranium and other radionuclides from groundwater. The improved membrane can also be applied to separation of other metal ions from aqueous streams in industrial operations.

  12. Innovative Process for Comprehensive Treatment of Liquid Radioactive Waste - 12551

    SciTech Connect

    Penzin, R.A.; Sarychev, G.A.

    2012-07-01

    This paper presents the results of research activities aimed at creation of a principally new LRW distilling treatment method. The new process is based on the instantaneous evaporation method widely used in distillation units. The main difference of the proposed process is that the vapor condensation is conducted without using heat exchangers in practically ideal mode by way of direct contacting in a vapor-liquid system. This process is conducted in a specially designed ejector unit in supersonic mode. Further recuperation of excess heat of vaporization is carried out in a standard heat exchanger. Such an arrangement of the process, together with use of the barometric height principle, allows to carry out LRW evaporation under low temperatures, which enables to use excess heat from NPS for heating initial LRW. Thermal calculations and model experiments have revealed that, in this case, the expenditure of energy for LRW treatment by distilling will not exceed 3 kilowatt-hour/m{sup 3}, which is comparable with the reverse-osmosis desalination method. Besides, the proposed devices are 4 to 5 times less metal-intensive than standard evaporation units. These devices are also characterized by versatility. Experiments have revealed that the new method can be used for evaporation of practically any types of LRW, including those containing a considerable amount of oil products. Owing to arrangement of the evaporation process at low temperatures, the new devices are not sensitive to 'scale formation'. This is why, they can be used for concentrating brines of up to 500-600 g/l. New types of such evaporating devices can be required both for LRW treatment processes at nuclear-power plants under design and for treating 'non-standard' LRW with complex physicochemical and radionuclide composition resulting from the disaster at the Fukushima I Nuclear Power Plant.) As a result of accidents at nuclear energy objects, as it has recently happened at NPP 'Fukushima-1', personnel faces

  13. Fast breeder reactor protection system

    DOEpatents

    van Erp, J.B.

    1973-10-01

    Reactor protection is provided for a liquid-metal-fast breeder reactor core by measuring the coolant outflow temperature from each of the subassemblies of the core. The outputs of the temperature sensors from a subassembly region of the core containing a plurality of subassemblies are combined in a logic circuit which develops a scram alarm if a predetermined number of the sensors indicate an over temperature condition. The coolant outflow from a single subassembly can be mixed with the coolant outflow from adjacent subassemblies prior to the temperature sensing to increase the sensitivity of the protection system to a single subassembly failure. Coherence between the sensors can be required to discriminate against noise signals. (Official Gazette)

  14. Fusion reactor breeder material safety compatibility studies

    SciTech Connect

    Jeppson, D.W.; Cohen, S.; Muhlestein, L.D.

    1983-09-01

    Tritium breeder material selection for fusion reactors is strongly influenced by the desire to minimize safety and environmental concerns. Breeder material safety compatibility studies are being conducted to identify and characterize breeder-coolant-material interactions under postulated reactor accident conditions. Recently completed scoping compatibility tests indicate the following. 1. Ternary oxides (LiAlO/sub 2/, Li/sub 2/ZrO/sub 3/, Li/sub 2/SiO/sub 3/, Li/sub 4/SiO/sub 4/, and LiTiO/sub 3/) at postulated blanket operating temperatures are chemically compatible with water coolant, while liquid lithium and Li/sub 7/Pb/sub 2/ reactions with water generate heat, aerosol, and hydrogen. 2. Lithium oxide and 17Li-83Pb alloy react mildly with water requiring special precautions to control hydrogen release. 3. Liquid lithium reacts substantially, while 17Li83Pb alloy reacts mildly with concrete to produce hydrogen. 4. Liquid lithium-air reactions may present some major safety concerns. Additional scoping tests are needed, but the ternary oxides, lithium oxide, and 17Li-83Pb have definite safety advantages over liquid lithium and Li/sub 7/Pb/sub 2/. The ternary oxides present minimal safetyrelated problems when used with water as coolant, air or concrete; but they do require neutron multipliers, which may have safety compatibility concerns with surrounding materials. The combined favorable neutronics and minor safety compatibility concerns of lithium oxide and 17Li-83Pb make them prime candidates as breeder materials. Current safety efforts are directed toward assessing the compatibility of lithium oxide and the lithium-lead alloy with coolants and other materials.

  15. US and Russian innovative technologies to process low-level liquid radioactive wastes: The Murmansk initiative

    SciTech Connect

    Dyer, R.S.; Penzin, R.; Duffey, R.B.; Sorlie, A.

    1996-12-31

    This paper documents the status of the technical design for the upgrade and expansion to the existing Low-level Liquid Radioactive Waste (LLLRW) treatment facility in Murmansk, the Russian Federation. This facility, owned by the Ministry of Transportation and operated by the Russian company RTP Atomflot in Murmansk, Russia, has been used by the Murmansk Shipping Company (MSCo) to process low-level liquid radioactive waste generated by the operation of its civilian icebreaker fleet. The purpose of the new design is to enable Russia to permanently cease the disposal at sea of LLLRW in the Arctic, and to treat liquid waste and high saline solutions from both the Civil and North Navy Fleet operations and decommissioning activities. Innovative treatments are to be used in the plant which are discussed in this paper.

  16. Ceramic breeder materials

    SciTech Connect

    Johnson, C.E.; Kummerer, K.R.; Roth, E.

    1987-01-01

    Ceramic materials are under investigation as potential breeder material in fusion reactors. This paper will review candidate materials with respect to fabrication routes and characterization, properties in as-fabricated and irradiated condition, and experimental results from laboratory and inpile investigations on tritium transport and release. Also discussed are the resources of beryllium, which is being considered as a neutron multiplier. The comparison of ceramic properties that is attempted here aims at the identification of the most-promising material for use in a tritium breeding blanket. 82 refs., 12 figs., 5 tabs.

  17. Innovative Poly(Ionic Liquid)s by the Polymerization of Deep Eutectic Monomers.

    PubMed

    Isik, Mehmet; Ruiperez, Fernando; Sardon, Haritz; Gonzalez, Alba; Zulfiqar, Sonia; Mecerreyes, David

    2016-07-01

    The incorporation of ionic liquid (IL) chemistry into functional polymers has extended the properties and applications of polyelectrolytes. However, ILs are expensive due to the presence of fluorinated anions or complicated synthetic steps which limit their technological viability. Here, we show a new family of poly(ionic liquid)s (PILs) which are based in cheap and renewable chemicals and involves facile synthetic approaches. Thus, deep eutectic monomers (DEMs) are prepared for the first time by using quaternary ammonium compounds and various hydrogen bond donors such as citric acid, terephthalic acid or an amidoxime. The deep eutectic formation is made through a simple mixing of the ingredients. Differential scanning calorimetry, nuclear magnetic resonance (NMR) and computational studies reveal the formation of the DEMs due to the ionic interactions. The resulting DEMs are liquid which facilitates their polymerization using mild photopolymerization or polycondensation strategies. Spectroscopic characterizations reveal the successful formation of the polymers. By this way, a new family of PILs can be synthesized which can be used for different applications. As an example, the polymers show promising performance as solid CO2 sorbents. Altogether the deep eutectic monomer route can lead to non-toxic, cheap and easy-to-prepare alternatives to current PILs for different applications. PMID:26954303

  18. Automated breeder fuel fabrication

    SciTech Connect

    Goldmann, L.H.; Frederickson, J.R.

    1983-09-01

    The objective of the Secure Automated Fabrication (SAF) Project is to develop remotely operated equipment for the processing and manufacturing of breeder reactor fuel pins. The SAF line will be installed in the Fuels and Materials Examination Facility (FMEF). The FMEF is presently under construction at the Department of Energy's (DOE) Hanford site near Richland, Washington, and is operated by the Westinghouse Hanford Company (WHC). The fabrication and support systems of the SAF line are designed for computer-controlled operation from a centralized control room. Remote and automated fuel fabriction operations will result in: reduced radiation exposure to workers; enhanced safeguards; improved product quality; near real-time accountability, and increased productivity. The present schedule calls for installation of SAF line equipment in the FMEF beginning in 1984, with qualifying runs starting in 1986 and production commencing in 1987. 5 figures.

  19. Utilizing FFTF: the keystone for breeder development

    SciTech Connect

    Ziff, J.J.; Arneson, S.O.

    1981-05-01

    This paper describes the role of the Fast Flux Test Facility (FFTF) in the US Department of Energy sponsored Liquid Metal Fast Breeder Reactor (LMFBR) Program. The programs that are in place to ensure that the FFTF fulfills its role as an essential key to the development of LMFBR technology are delineated. A detailed FFTF Operating Plan has been developed to present in integrated form the strategy for gaining maximum useful information from the planned FFTF operations. The three principal areas of FFTF Utilization: Plant Utilization, Irradiation Testing, and Safety, combine to form the overall FFTF Operating Plan. Primary areas where FFTF is already making major contributions to LMFBR development are described.

  20. Innovators.

    ERIC Educational Resources Information Center

    NEA Today, 2001

    2001-01-01

    Describes various innovations that have been developed to enhance education. These innovations include: helping educators help at-risk students succeed; promoting high school journalism; ensuring quality online learning experiences; developing a student performing group that uses theater to address social issues; and having students design their…

  1. EBIS charge breeder for CARIBU.

    PubMed

    Kondrashev, S; Barcikowski, A; Dickerson, C; Fischer, R; Ostroumov, P N; Vondrasek, R; Pikin, A

    2014-02-01

    A high-efficiency charge breeder based on an Electron Beam Ion Source (EBIS) is being developed by the ANL Physics Division to increase the intensity and improve the purity of accelerated radioactive ion beams. A wide variety of low-energy neutron-rich ion beams are produced by the Californium Rare Isotope Breeder Upgrade (CARIBU) for the Argonne Tandem Linac Accelerator System (ATLAS). These beams will be charge-bred by an EBIS charge breeder to a charge-to-mass ratio (q/A) ≥ 1/7 and accelerated by ATLAS to energies of about 10 MeV/u. The assembly of the CARIBU EBIS charge breeder except the injection/extraction beam lines has been completed. This summer we started electron beam commissioning of the EBIS. The first results on electron beam extraction, transport from the electron gun to a high power electron collector are presented and discussed. PMID:24593606

  2. EBIS charge breeder for CARIBU

    NASA Astrophysics Data System (ADS)

    Kondrashev, S.; Barcikowski, A.; Dickerson, C.; Fischer, R.; Ostroumov, P. N.; Vondrasek, R.; Pikin, A.

    2014-02-01

    A high-efficiency charge breeder based on an Electron Beam Ion Source (EBIS) is being developed by the ANL Physics Division to increase the intensity and improve the purity of accelerated radioactive ion beams. A wide variety of low-energy neutron-rich ion beams are produced by the Californium Rare Isotope Breeder Upgrade (CARIBU) for the Argonne Tandem Linac Accelerator System (ATLAS). These beams will be charge-bred by an EBIS charge breeder to a charge-to-mass ratio (q/A) ≥ 1/7 and accelerated by ATLAS to energies of about 10 MeV/u. The assembly of the CARIBU EBIS charge breeder except the injection/extraction beam lines has been completed. This summer we started electron beam commissioning of the EBIS. The first results on electron beam extraction, transport from the electron gun to a high power electron collector are presented and discussed.

  3. Level monitoring system with pulsating sensor—Application to online level monitoring of dashpots in a fast breeder reactor

    SciTech Connect

    Malathi, N.; Sahoo, P. Ananthanarayanan, R.; Murali, N.

    2015-02-15

    An innovative continuous type liquid level monitoring system constructed by using a new class of sensor, viz., pulsating sensor, is presented. This device is of industrial grade and it is exclusively used for level monitoring of any non conducting liquid. This instrument of unique design is suitable for high resolution online monitoring of oil level in dashpots of a sodium-cooled fast breeder reactor. The sensing probe is of capacitance type robust probe consisting of a number of rectangular mirror polished stainless steel (SS-304) plates separated with uniform gaps. The performance of this novel instrument has been thoroughly investigated. The precision, sensitivity, response time, and the lowest detection limit in measurement using this device are <0.01 mm, ∼100 Hz/mm, ∼1 s, and ∼0.03 mm, respectively. The influence of temperature on liquid level is studied and the temperature compensation is provided in the instrument. The instrument qualified all recommended tests, such as environmental, electromagnetic interference and electromagnetic compatibility, and seismic tests prior to its deployment in nuclear reactor. With the evolution of this level measurement approach, it is possible to provide dashpot oil level sensors in fast breeder reactor for the first time for continuous measurement of oil level in dashpots of Control and Safety Rod Drive Mechanism during reactor operation.

  4. Level monitoring system with pulsating sensor—Application to online level monitoring of dashpots in a fast breeder reactor

    NASA Astrophysics Data System (ADS)

    Malathi, N.; Sahoo, P.; Ananthanarayanan, R.; Murali, N.

    2015-02-01

    An innovative continuous type liquid level monitoring system constructed by using a new class of sensor, viz., pulsating sensor, is presented. This device is of industrial grade and it is exclusively used for level monitoring of any non conducting liquid. This instrument of unique design is suitable for high resolution online monitoring of oil level in dashpots of a sodium-cooled fast breeder reactor. The sensing probe is of capacitance type robust probe consisting of a number of rectangular mirror polished stainless steel (SS-304) plates separated with uniform gaps. The performance of this novel instrument has been thoroughly investigated. The precision, sensitivity, response time, and the lowest detection limit in measurement using this device are <0.01 mm, ˜100 Hz/mm, ˜1 s, and ˜0.03 mm, respectively. The influence of temperature on liquid level is studied and the temperature compensation is provided in the instrument. The instrument qualified all recommended tests, such as environmental, electromagnetic interference and electromagnetic compatibility, and seismic tests prior to its deployment in nuclear reactor. With the evolution of this level measurement approach, it is possible to provide dashpot oil level sensors in fast breeder reactor for the first time for continuous measurement of oil level in dashpots of Control & Safety Rod Drive Mechanism during reactor operation.

  5. Level monitoring system with pulsating sensor--application to online level monitoring of dashpots in a fast breeder reactor.

    PubMed

    Malathi, N; Sahoo, P; Ananthanarayanan, R; Murali, N

    2015-02-01

    An innovative continuous type liquid level monitoring system constructed by using a new class of sensor, viz., pulsating sensor, is presented. This device is of industrial grade and it is exclusively used for level monitoring of any non conducting liquid. This instrument of unique design is suitable for high resolution online monitoring of oil level in dashpots of a sodium-cooled fast breeder reactor. The sensing probe is of capacitance type robust probe consisting of a number of rectangular mirror polished stainless steel (SS-304) plates separated with uniform gaps. The performance of this novel instrument has been thoroughly investigated. The precision, sensitivity, response time, and the lowest detection limit in measurement using this device are <0.01 mm, ∼100 Hz/mm, ∼1 s, and ∼0.03 mm, respectively. The influence of temperature on liquid level is studied and the temperature compensation is provided in the instrument. The instrument qualified all recommended tests, such as environmental, electromagnetic interference and electromagnetic compatibility, and seismic tests prior to its deployment in nuclear reactor. With the evolution of this level measurement approach, it is possible to provide dashpot oil level sensors in fast breeder reactor for the first time for continuous measurement of oil level in dashpots of Control & Safety Rod Drive Mechanism during reactor operation. PMID:25725884

  6. Laser fusion driven breeder design study. Final report

    SciTech Connect

    Berwald, D.H.; Massey, J.V.

    1980-12-01

    The results of the Laser Fusion Breeder Design Study are given. This information primarily relates to the conceptual design of an inertial confinement fusion (ICF) breeder reactor (or fusion-fission hybrid) based upon the HYLIFE liquid metal wall protection concept developed at Lawrence Livermore National Laboratory. The blanket design for this breeder is optimized to both reduce fissions and maximize the production of fissile fuel for subsequent use in conventional light water reactors (LWRs). When the suppressed fission blanket is compared with its fast fission counterparts, a minimal fission rate in the blanket results in a unique reactor safety advantage for this concept with respect to reduced radioactive inventory and reduced fission product decay afterheat in the event of a loss-of-coolant-accident.

  7. Use of liquid metals in nuclear and thermonuclear engineering, and in other innovative technologies

    NASA Astrophysics Data System (ADS)

    Rachkov, V. I.; Arnol'dov, M. N.; Efanov, A. D.; Kalyakin, S. G.; Kozlov, F. A.; Loginov, N. I.; Orlov, Yu. I.; Sorokin, A. P.

    2014-05-01

    By now, a good deal of experience has been gained with using liquid metals as coolants in nuclear power installations; extensive knowledge has been gained about the physical, thermophysical, and physicochemical properties of these coolants; and the scientific principles and a set of methods and means for handling liquid metals as coolants for nuclear power installations have been elaborated. Prototype and commercialgrade sodium-cooled NPP power units have been developed, including the BOR-60, BN-350, and BN-600 power units (the Soviet Union); the Rapsodie, Phenix, and Superphenix power units (France), the EBR-II power unit (the United States); and the PFR power unit (the United Kingdom). In Russia, dedicated nuclear power installations have been constructed, including those with a lead-bismuth coolant for nuclear submarines and with sodium-potassium alloy for spacecraft (the Buk and Topol installations), which have no analogs around the world. Liquid metals (primarily lithium and its alloy with lead) hold promise for use in thermonuclear power engineering, where they can serve not only as a coolant, but also as tritium-producing medium. In this article, the physicochemical properties of liquid metal coolants, as well as practical experience gained from using them in nuclear and thermonuclear power engineering and in innovative technologies are considered, and the lines of further research works are formulated. New results obtained from investigations carried out on the Pb-Bi and Pb for the SVBR and BREST fast-neutron reactors (referred to henceforth as fast reactors) and for controlled accelerator systems are described.

  8. Probabilities of inherent shutdown of unprotected events in innovative liquid metal reactors

    SciTech Connect

    Mueller, C.J.; Wade, D.C.

    1988-01-01

    The uncertainty in predicting the effectiveness of inherent shutdown in innovative liquid metal cooled reactors with metallic fuel results from three broad contributing areas of uncertainty: (1) the inability to exactly predict the frequency of ATWS events with potential to challenge the safety systems and require inherent shutdown; (2) the approximation of representing all such events by a selected set of ''generic scenarios''; and (3) the inability to exactly calculate the core response to the selected generic scenarios. This paper discusses the work being done to address each of these contributing areas, identifies the design and research approaches being used at Argonne National Laboratory to reducing the key contributions to uncertainties in inherent shutdown, and presents results. The conditional probabilities (given ATWS initiation) of achieving temperatures capable of defeating inherent shutdown are shown to range from /approximately/0.1% to negligible for current designs.

  9. Fusion Breeder Program interim report

    SciTech Connect

    Moir, R.; Lee, J.D.; Neef, W.

    1982-06-11

    This interim report for the FY82 Fusion Breeder Program covers work performed during the scoping phase of the study, December, 1981-February 1982. The goals for the FY82 study are the identification and development of a reference blanket concept using the fission suppression concept and the definition of a development plan to further the fusion breeder application. The context of the study is the tandem mirror reactor, but emphasis is placed upon blanket engineering. A tokamak driver and blanket concept will be selected and studied in more detail during FY83.

  10. Liquid Metal Fast Breeder Reactors: a bibliography

    SciTech Connect

    Raleigh, H.D.

    1980-11-01

    This bibliogralphy includes 5465 selected citations on LMFBR development. The citations were compiled from the DOE Energy Data Base covering the period January 1978 (EDB File No. 78R1087) through August 1980 (EDB File No. 80C79142). The references are to reports from the Department of Energy and its contractors, reports from other government or private organizations, and journal articles, books, conference papers, and monographs from US originators. Report citations are arranged alphanumerically by report number; nonreport literature citations are arranged chronologically. Corporate, Personal Author, Subject, and Report Number Indexes are provided in Volume 2.

  11. Liquid Metal Fast Breeder Reactors: a bibliography

    SciTech Connect

    Raleigh, H.D.

    1980-11-01

    This bibliography includes 5465 selected citations on LMFBR development. The citations were compiled from the DOE Energy Data Base covering the period January 1978 (EDB File No. 78R1087) through August 1980 (EDB File No. 80C79142). The references are to reports from the Department of Energy and its contractors, reports from other government or private organizations, and journal articles, books, conference papers, and monographs from US originators. Report citations are arranged alphanumerically by report number; nonreport literature citations are arranged chronologically. Corporate, Personal Author, Subject, and Report Number Indexes are provided in Volume 2.

  12. NUCLEAR REACTOR FUEL-BREEDER FUEL ELEMENT

    DOEpatents

    Currier, E.L. Jr.; Nicklas, J.H.

    1962-08-14

    A fuel-breeder fuel element was developed for a nuclear reactor wherein discrete particles of fissionable material are dispersed in a matrix of fertile breeder material. The fuel element combines the advantages of a dispersion type and a breeder-type. (AEC)

  13. Thermal baffle for fast-breeder reacton

    DOEpatents

    Rylatt, John A.

    1977-01-01

    A liquid-metal-cooled fast-breeder reactor includes a bridge structure for separating hot outlet coolant from relatively cool inlet coolant consisting of an annular stainless steel baffle plate extending between the core barrel surrounding the core and the thermal liner associated with the reactor vessel and resting on ledges thereon, there being inner and outer circumferential webs on the lower surface of the baffle plate and radial webs extending between the circumferential webs, a stainless steel insulating plate completely covering the upper surface of the baffle plate and flex seals between the baffle plate and the ledges on which the baffle plate rests to prevent coolant from washing through the gaps therebetween. The baffle plate is keyed to the core barrel for movement therewith and floating with respect to the thermal liner and reactor vessel.

  14. Analyses of various options for the breeder fuel cycle in the United States

    SciTech Connect

    Burch, W.D.; Stradley, J.G.; Yook, H.R.; Lerch, R.E.

    1985-01-01

    The US Department of Energy (DOE) has established a program to develop innovative liquid metal reactor (LMR) designs to assist in developing US future reactor strategy. This paper describes studies in progress to examine various fuel cycle strategies that relate to the reactor strategy. Three potential fuel cycle options that focus on supporting an initial 1300-MWe reactor station have been defined: completion and utilization of the Breeder Reprocessing Engineering Test/Secure Automated Fabrication (BRET/SAF) in the Fuels and Materials Examination Facility (FMEF); a co-located fuel cycle facility; and delayed closure of the fuel cycle for five to ten years. It appears feasible to increase the capacity of the original BRET design and SAF in the FMEF to accommodate the projected output (up to 35 MTHM/year) from the 1300-MWe liquid-metal concepts under study. Working with the reactor manufacturers, criteria were developed for a small fuel cycle facility co-located at a utility reactor site. The requirements considered the need to be able to support as little as approximately 400 MWe to as much as 35 MTHM/year reprocessing capability. A rough order-of-magnitude capital cost estimate ($300 million) was developed. Plans developed within the US Consolidated Management Office for an initial reactor project have envisioned that a cost savings could be realized by delaying closure of the fuel cycle as long as supplies of plutonium could be obtained relatively inexpensively. This might prove to be only five to ten years, but even that period might be long enough for the fuel cycle costs to be spread over more than one reactor rather than loaded on the initial project. This concept is being explored as is the question of the future coupling of a light water reactor (LWR) reprocessing industry for plutonium supply to breeder recycle. 12 figs.

  15. Rapid comparison of a candidate biosimilar to an innovator monoclonal antibody with advanced liquid chromatography and mass spectrometry technologies.

    PubMed

    Xie, Hongwei; Chakraborty, Asish; Ahn, Joomi; Yu, Ying Qing; Dakshinamoorthy, Deepalakshmi P; Gilar, Martin; Chen, Weibin; Skilton, St John; Mazzeo, Jeffery R

    2010-01-01

    This study shows that state-of-the-art liquid chromatography (LC) and mass spectrometry (MS) can be used for rapid verification of identity and characterization of sequence variants and posttranslational modifications (PTMs) for antibody products. A candidate biosimilar IgG1 monoclonal antibody (mAb) was compared in detail to a commercially available innovator product. Intact protein mass, primary sequence, PTMs, and the micro-differences between the two mAbs were identified and quantified simultaneously. Although very similar in terms of sequences and modifications, a mass difference observed by LC-MS intact mass measurements indicated that they were not identical. Peptide mapping, performed with data independent acquisition LC-MS using an alternating low and elevated collision energy scan mode (LC-MS(E)), located the mass difference between the biosimilar and the innovator to a two amino acid residue variance in the heavy chain sequences. The peptide mapping technique was also used to comprehensively catalogue and compare the differences in PTMs of the biosimilar and innovator mAbs. Comprehensive glycosylation profiling confirmed that the proportion of individual glycans was different between the biosimilar and the innovator, although the number and identity of glycans were the same. These results demonstrate that the combination of accurate intact mass measurement, released glycan profiling, and LC-MS(E) peptide mapping provides a set of routine tools that can be used to comprehensively compare a candidate biosimilar and an innovator mAb. PMID:20458189

  16. Rapid comparison of a candidate biosimilar to an innovator monoclonal antibody with advanced liquid chromatography and mass spectrometry technologies

    PubMed Central

    Xie, Hongwei; Chakraborty, Asish; Ahn, Joomi; Yu, Ying Qing; Dakshinamoorthy, Deepalakshmi P; Gilar, Martin; Chen, Weibin; Skilton, St John

    2010-01-01

    This study shows that state-of-the-art liquid chromatography (LC) and mass spectrometry (MS) can be used for rapid verification of identity and characterization of sequence variants and posttranslational modifications (PTMs) for antibody products. A candidate biosimilar IgG1 monoclonal antibody (mAb) was compared in detail to a commercially available innovator product. Intact protein mass, primary sequence, PTMs and the micro-differences between the two mAbs were identified and quantified simultaneously. Although very similar in terms of sequences and modifications, a mass difference observed by LC-MS intact mass measurements indicated that they were not identical. Peptide mapping, performed with data independent acquisition LC-MS using an alternating low and elevated collision energy scan mode (LC-MSE), located the mass difference between the biosimilar and the innovator to a two amino acid residue variance in the heavy chain sequences. The peptide mapping technique was also used to comprehensively catalogue and compare the differences in PTMs of the biosimilar and innovator mAbs. Comprehensive glycosylation profiling confirmed that the proportion of individual glycans was different between the biosimilar and the innovator, although the number and identity of glycans were the same. These results demonstrate that the combination of accurate intact mass measurement, released glycan profiling and LC-MSE peptide mapping provides a set of routine tools that can be used to comprehensively compare a candidate biosimilar and an innovator mAb. PMID:20458189

  17. Proceedings of waste stream minimization and utilization innovative concepts: An experimental technology exchange. Volume 2, Industrial liquid waste processing, industrial gaseous waste processing

    SciTech Connect

    Lee, V.E.; Watts, R.L.

    1993-04-01

    This two-volume proceedings summarize the results of fifteen innovations that were funded through the US Department of Energy`s Innovative Concept Program. The fifteen innovations were presented at the sixth Innovative Concepts Fair, held in Austin, Texas, on April 22--23, 1993. The concepts in this year`s fair address innovations that can substantially reduce or use waste streams. Each paper describes the need for the proposed concept, the concept being proposed, and the concept`s economics and market potential, key experimental results, and future development needs. The papers are divided into two volumes: Volume 1 addresses innovations for industrial solid waste processing and municipal waste reduction/recycling, and Volume 2 addresses industrial liquid waste processing and industrial gaseous waste processing. Individual reports are indexed separately.

  18. Breeding nuclear fuels with accelerators: replacement for breeder reactors

    SciTech Connect

    Grand, P.; Takahashi, H.

    1984-01-01

    One application of high energy particle accelerators has been, and still is, the production of nuclear fuel for the nuclear energy industry; tantalizing because it would create a whole new industry. This approach to producing fissile from fertile material was first considered in the early 1950's in the context of the nuclear weapons program. A considerable development effort was expended before discovery of uranium ore in New Mexico put an end to the project. Later, US commitment to the Liquid Metal Fast Breeder Reactors (LMFBR) killed any further interest in pursuing accelerator breeder technology. Interest in the application of accelerators to breed nuclear fuels, and possibly burn nuclear wastes, revived in the late 1970's, when the LMFBR came under attack during the Carter administration. This period gave the opportunity to revisit the concept in view of the present state of the technology. This evaluation and the extensive calculational modeling of target designs that have been carried out are promising. In fact, a nuclear fuel cycle of Light Water Reactors and Accelerator Breeders is competitive to that of the LMFBR. At this time, however, the relative abundance of uranium reserves vs electricity demand and projected growth rate render this study purely academic. It will be for the next generation of accelerator builders to demonstate the competitiveness of this technology versus that of other nuclear fuel cycles, such as LMFBR's or Fusion Hybrid systems. 22 references, 1 figure, 5 tables.

  19. Innovation, Innovation, Innovation

    ERIC Educational Resources Information Center

    Schuller, Tom

    2007-01-01

    Innovation, Universities and Skills. The new title of the department offers much food for thought. The title is indeed an intriguing and important one. Bringing the idea of innovation right to the fore is, to use an overworked term, challenging. Pinning down what innovation means is not at all easy. There are three different lines of argument. The…

  20. Thermal breeder fuel enrichment zoning

    DOEpatents

    Capossela, Harry J.; Dwyer, Joseph R.; Luce, Robert G.; McCoy, Daniel F.; Merriman, Floyd C.

    1992-01-01

    A method and apparatus for improving the performance of a thermal breeder reactor having regions of higher than average moderator concentration are disclosed. The fuel modules of the reactor core contain at least two different types of fuel elements, a high enrichment fuel element and a low enrichment fuel element. The two types of fuel elements are arranged in the fuel module with the low enrichment fuel elements located between the high moderator regions and the high enrichment fuel elements. Preferably, shim rods made of a fertile material are provided in selective regions for controlling the reactivity of the reactor by movement of the shim rods into and out of the reactor core. The moderation of neutrons adjacent the high enrichment fuel elements is preferably minimized as by reducing the spacing of the high enrichment fuel elements and/or using a moderator having a reduced moderating effect.

  1. Light-Water Breeder Reactor

    DOEpatents

    Beaudoin, B. R.; Cohen, J. D.; Jones, D. H.; Marier, Jr, L. J.; Raab, H. F.

    1972-06-20

    Described is a light-water-moderated and -cooled nuclear breeder reactor of the seed-blanket type characterized by core modules comprising loosely packed blanket zones enriched with fissile fuel and axial zoning in the seed and blanket regions within each core module. Reactivity control over lifetime is achieved by axial displacement of movable seed zones without the use of poison rods in the embodiment illustrated. The seed is further characterized by a hydrogen-to-uranium-233 atom ratio in the range 10 to 200 and a uranium-233-to-thorium-232 atom ratio ranging from 0.012 to 0.200. The seed occupies from 10 to 35 percent of the core volume in the form of one or more individual islands or annuli. (NSA 26: 55130)

  2. Instrumentation and control improvements at Experimental Breeder Reactor II

    SciTech Connect

    Christensen, L.J.; Planchon, H.P.

    1993-01-01

    The purpose of this paper is to describe instrumentation and control (I C) system improvements at Experimental Breeder Reactor 11 (EBR-11). The improvements are focused on three objectives; to keep the reactor and balance of plant (BOP) I C systems at a high level of reliability, to provide diagnostic systems that can provide accurate information needed for analysis of fuel performance, and to provide systems that will be prototypic of I C systems of the next generation of liquid metal reactor (LMR) plants.

  3. Instrumentation and control improvements at Experimental Breeder Reactor II

    SciTech Connect

    Christensen, L.J.; Planchon, H.P.

    1993-03-01

    The purpose of this paper is to describe instrumentation and control (I&C) system improvements at Experimental Breeder Reactor 11 (EBR-11). The improvements are focused on three objectives; to keep the reactor and balance of plant (BOP) I&C systems at a high level of reliability, to provide diagnostic systems that can provide accurate information needed for analysis of fuel performance, and to provide systems that will be prototypic of I&C systems of the next generation of liquid metal reactor (LMR) plants.

  4. Liquid nitrogen-cooled diamond-wire concrete cutting. Innovative technology summary report

    SciTech Connect

    1998-12-01

    Liquid nitrogen-cooled diamond-wire concrete cutting can be used to cut through thick concrete walls, floors, and structures without using water to cool the cutting wire. The diamond wire is cooled with liquid nitrogen in a 0.9-m (3-ft) long by 7.6-cm (3-in.) diameter pipe housing. The nitrogen evaporates, so no contaminated liquid waste is generated. Other than the use of liquid nitrogen, the system is a conventional diamond-wire saw assembly with remote hydraulic controls. Setup of the hydraulic-powered drive wheel and the diamond wire for cutting requires a relatively short period of time using people with minimal training. Concrete dust generated during the cutting is considerable and requires control. The production rate of this improved technology is 0.78 m{sup 2}/hr (8.4 ft{sup 2}/hr). The production rates of traditional (baseline) water-cooled diamond-wire cutting and circular saw cutting technologies are 1.11 m{sup 2}/hr (12 ft{sup 2}/hr), and 0.45 m{sup 2}/hr (4.8 ft{sup 2}/hr), respectively. The liquid nitrogen-cooled system costs 189% more than conventional diamond-wire cutting if contaminated liquid wastes collection, treatment, and disposal are not accounted for with the baseline. The new technology was 310% more costly than a conventional diamond circular saw, under the conditions of this demonstration (no wastewater control). For cutting a 0.9-m x 3.7-m (3-ft x 12-ft) wall, the improved technology costs $17,000, while baseline diamond-wire cutting would cost $9,000 and baseline circular-saw cutting would cost $5,500. The improved system may cost less than the baseline technologies or may be comparable in cost if wastewater control is included.

  5. Comparison of oxide- and metal-core behavior during CRBRP (Clinch River Breeder Reactor Plant) station blackout

    SciTech Connect

    Polkinghorne, S T; Atkinson, S A

    1986-01-01

    A resurrected concept that could significantly improve the inherently safe response of Liquid-Metal cooled Reactors (LMRs) during severe undercooling transients is the use of metallic fuel. Analytical studies have been reported on for the transient behavior of metal-fuel cores in innovative, inherently safe LMR designs. This paper reports on an analysis done, instead, for the Clinch River Breeder Reactor Plant (CRBRP) design with the only innovative change being the incorporation of a metal-fuel core. The SSC-L code was used to simulate a protected station blackout accident in the CRBRP with a 943 MWt Integral Fast Reactor (IFR) metal-fuel core. The results, compared with those for the oxide-fueled CRBRP, show that the margin to boiling is greater for the IFR core. However, the cooldown transient is more severe due to the faster thermal response time of metallic fuel. Some additional calculations to assess possible LMR design improvements (reduced primary system pressure losses, extended flow coastdown) are also discussed. 8 refs., 13 figs., 2 tabs.

  6. Use of biomass for producing liquid fuel: Current state and innovations

    NASA Astrophysics Data System (ADS)

    Chernova, N. I.; Korobkova, T. P.; Kiseleva, S. V.

    2010-11-01

    Current matters relating to utilization of biomass for producing energy are discussed, including the most developed technologies of biopower engineering and innovative developments, as well as the possibilities of using nonfood raw materials as second-generation biofuel. It is shown that microalgae can be considered as prospective sources of different kinds of renewable biofuel, such as methane, biohydrogen, bioethanol, biobutanol, pyrolysis biofuel, biodiesel, and renewable diesel fuel, and can serve as an alternative to the traditional cultures used for power-generating purposes.

  7. Current applications of liquid chromatography/mass spectrometry in pharmaceutical discovery after a decade of innovation.

    PubMed

    Ackermann, Bradley L; Berna, Michael J; Eckstein, James A; Ott, Lee W; Chaudhary, Ajai K

    2008-01-01

    Current drug discovery involves a highly iterative process pertaining to three core disciplines: biology, chemistry, and drug disposition. For most pharmaceutical companies the path to a drug candidate comprises similar stages: target identification, biological screening, lead generation, lead optimization, and candidate selection. Over the past decade, the overall efficiency of drug discovery has been greatly improved by a single instrumental technique, liquid chromatography/mass spectrometry (LC/MS). Transformed by the commercial introduction of the atmospheric pressure ionization interface in the mid-1990s, LC/MS has expanded into almost every area of drug discovery. In many cases, drug discovery workflow has been changed owing to vastly improved efficiency. This review examines recent trends for these three core disciplines and presents seminal examples where LC/MS has altered the current approach to drug discovery. PMID:20636083

  8. Advanced absorber assembly design for breeder reactors

    SciTech Connect

    Pitner, A.L.; Birney, K.R.

    1980-01-01

    An advanced absorber assembly design has been developed for breeder reactor control rod applications that provides for improved in-reactor performance, longer lifetimes, and reduced fabrication costs. The design comprises 19 vented pins arranged in a circular array inside of round duct tubes. The absorber material is boron carbide; cladding and duct components are constructed from the modified Type 316 stainless steel alloy. Analyses indicate that this design will scram 30 to 40% faster than the reference FFTF absorber assembly. The basic design characteristics of this advanced FFTF absorber assembly are applicable to large core breeder reactor design concepts.

  9. Preapplication safety evaluation report for the Power Reactor Innovative Small Module (PRISM) liquid-metal reactor. Final report

    SciTech Connect

    Donoghue, J.E.; Donohew, J.N.; Golub, G.R.; Kenneally, R.M.; Moore, P.B.; Sands, S.P.; Throm, E.D.; Wetzel, B.A.

    1994-02-01

    This preapplication safety evaluation report (PSER) presents the results of the preapplication desip review for die Power Reactor Innovative Small Module (PRISM) liquid-mew (sodium)-cooled reactor, Nuclear Regulatory Commission (NRC) Project No. 674. The PRISM conceptual desip was submitted by the US Department of Energy in accordance with the NRC`s ``Statement of Policy for the Regulation of Advanced Nuclear Power Plants`` (51 Federal Register 24643). This policy provides for the early Commission review and interaction with designers and licensees. The PRISM reactor desip is a small, modular, pool-type, liquid-mew (sodium)-cooled reactor. The standard plant design consists of dim identical power blocks with a total electrical output rating of 1395 MWe- Each power block comprises three reactor modules, each with a thermal rating of 471 MWt. Each module is located in its own below-grade silo and is co to its own intermediate heat transport system and steam generator system. The reactors utilize a metallic-type fuel, a ternary alloy of U-Pu-Zr. The design includes passive reactor shutdown and passive decay heat removal features. The PSER is the NRC`s preliminary evaluation of the safety features in the PRISM design, including the projected research and development programs required to support the design and the proposed testing needs. Because the NRC review was based on a conceptual design, the PSER did not result in an approval of the design. Instead it identified certain key safety issues, provided some guidance on applicable licensing criteria, assessed the adequacy of the preapplicant`s research and development programs, and concluded that no obvious impediments to licensing the PRISM design had been identified.

  10. Carbon-supported ionic liquids as innovative adsorbents for CO₂ separation from synthetic flue-gas.

    PubMed

    Erto, Alessandro; Silvestre-Albero, Ana; Silvestre-Albero, Joaquín; Rodríguez-Reinoso, Francisco; Balsamo, Marco; Lancia, Amedeo; Montagnaro, Fabio

    2015-06-15

    Fixed-bed thermodynamic CO2 adsorption tests were performed in model flue-gas onto Filtrasorb 400 and Nuchar RGC30 activated carbons (AC) functionalized with [Hmim][BF4] and [Emim][Gly] ionic liquids (IL). A comparative analysis of the CO2 capture results and N2 porosity characterization data evidenced that the use of [Hmim][BF4], a physical solvent for carbon dioxide, ended up into a worsening of the parent AC capture performance, due to a dominating pore blocking effect at all the operating temperatures. Conversely, the less sterically-hindered and amino acid-based [Emim][Gly] IL was effective in increasing the AC capture capacity at 353 K under milder impregnation conditions, the beneficial effect being attributed to both its chemical affinity towards CO2 and low pore volume reduction. The findings derived in this work outline interesting perspectives for the application of amino acid-based IL supported onto activated carbons for CO2 separation under post-combustion conditions, and future research efforts should be focused on the search for AC characterized by optimal pore size distribution and surface properties for IL functionalization. PMID:25710387

  11. Fast Breeder Reactors in Sweden: Vision and Reality.

    PubMed

    Fjaestad, Maja

    2015-01-01

    The fast breeder is a type of nuclear reactor that aroused much attention in the 1950s and '60s. Its ability to produce more nuclear fuel than it consumes offered promises of cheap and reliable energy. Sweden had advanced plans for a nuclear breeder program, but canceled them in the middle of the 1970s with the rise of nuclear skepticism. The article investigates the nuclear breeder as a technological vision. The nuclear breeder reactor is an example of a technological future that did not meet its industrial expectations. But that does not change the fact that the breeder was an influential technology. Decisions about the contemporary reactors were taken with the idea that in a foreseeable future they would be replaced with the efficient breeder. The article argues that general themes in the history of the breeder reactor can deepen our understanding of the mechanisms behind technological change. PMID:26334698

  12. Statement of the Executive Committee of the Scientists' Institute for Public Information--Comments on the Breeder Reactor

    ERIC Educational Resources Information Center

    Environment, 1975

    1975-01-01

    Inheritance of the Atomic Energy Commission's Draft Environmental Impact Statement for the Liquid Metal Fast Breeder Reactor Program by the Energy Research and Development Administration has caused much concern among members of the Scientists' Institute for Public Information (SIPI). SIPI members are concerned about the inadequacy and economic…

  13. Alternative reproductive tactics in female striped mice: Solitary breeders have lower corticosterone levels than communal breeders.

    PubMed

    Hill, Davina L; Pillay, Neville; Schradin, Carsten

    2015-05-01

    Alternative reproductive tactics (ARTs), where members of the same sex and population show distinct reproductive phenotypes governed by decision-rules, have been well-documented in males of many species, but are less well understood in females. The relative plasticity hypothesis (RPH) predicts that switches between plastic ARTs are mediated by changes in steroid hormones. This has received much support in males, but little is known about the endocrine control of female ARTs. Here, using a free-living population of African striped mice (Rhabdomys pumilio) over five breeding seasons, we tested whether females following different tactics differed in corticosterone and testosterone levels, as reported for male striped mice using ARTs, and in progesterone and oestrogen, which are important in female reproduction. Female striped mice employ three ARTs: communal breeders give birth in a shared nest and provide alloparental care, returners leave the group temporarily to give birth, and solitary breeders leave to give birth and do not return. We expected communal breeders and returners to have higher corticosterone, owing to the social stress of group-living, and lower testosterone than solitary breeders, which must defend territories alone. Solitary breeders had lower corticosterone than returners and communal breeders, as predicted, but testosterone and progesterone did not differ between ARTs. Oestrogen levels were higher in returners (measured before leaving the group) than in communal and solitary breeders, consistent with a modulatory role. Our study demonstrates hormonal differences between females following (or about to follow) different tactics, and provides the first support for the RPH in females. PMID:25828632

  14. Current experimental activities for solid breeder development

    SciTech Connect

    Johnson, C.E.; Hollenberg, G.W.; Roux, N.; Watanabe, H.

    1988-01-01

    The current data base for ceramic breeder materials does not exhibit any negative features as regards to thermophysical, mechanical, and irradiation behavior. All candidate materials show excellent stability for irradiation testing to 3% burnup. In-situ tritium recovery tests show very low tritium inventories for all candidates. Theoretical models are being developed to accurately predict real time release rates. Fabrication of kilogram quantities of materials has been achieved and technology is available for further scale-up.

  15. Experimental Breeder Reactor I Preservation Plan

    SciTech Connect

    Julie Braun

    2006-10-01

    Experimental Breeder Reactor I (EBR I) is a National Historic Landmark located at the Idaho National Laboratory, a Department of Energy laboratory in southeastern Idaho. The facility is significant for its association and contributions to the development of nuclear reactor testing and development. This Plan includes a structural assessment of the interior and exterior of the EBR I Reactor Building from a preservation, rather than an engineering stand point and recommendations for maintenance to ensure its continued protection.

  16. BREEDER: a microcomputer program for financial analysis of a large-scale prototype breeder reactor

    SciTech Connect

    Giese, R.F.

    1984-04-01

    This report describes a microcomputer-based, single-project financial analysis program: BREEDER. BREEDER is a user-friendly model designed to facilitate frequent and rapid analyses of the financial implications associated with alternative design and financing strategies for electric generating plants and large-scale prototype breeder (LSPB) reactors in particular. The model has proved to be a useful tool in establishing cost goals for LSPB reactors. The program is available on floppy disks for use on an IBM personal computer (or IBM look-a-like) running under PC-DOS or a Kaypro II transportable computer running under CP/M (and many other CP/M machines). The report documents version 1.5 of BREEDER and contains a user's guide. The report also includes a general overview of BREEDER, a summary of hardware requirements, a definition of all required program inputs, a description of all algorithms used in performing the construction-period and operation-period analyses, and a summary of all available reports. The appendixes contain a complete source-code listing, a cross-reference table, a sample interactive session, several sample runs, and additional documentation of the net-equity program option.

  17. Do avian cooperative breeders live longer?

    PubMed Central

    Beauchamp, Guy

    2014-01-01

    Cooperative breeding is not common in birds but intriguingly over-represented in several families, suggesting that predisposing factors, similar ecological constraints or a combination of the two facilitate the evolution of this breeding strategy. The life-history hypothesis proposes that cooperative breeding is facilitated by high annual survival, which increases the local population and leads to a shortage of breeding opportunities. Clutch size in cooperative breeders is also expected to be smaller. An earlier comparative analysis in a small sample of birds supported the hypothesis but this conclusion has been controversial. Here, I extend the analysis to a larger, worldwide sample and take into account potential confounding factors that may affect estimates of a slow pace of life and clutch size. In a sample of 81 species pairs consisting of closely related cooperative and non-cooperative breeders, I did not find an association between maximum longevity and cooperative breeding, controlling for diet, body mass and sampling effort. However, in a smaller sample of 37 pairs, adult annual survival was indeed higher in the cooperative breeders, controlling for body mass. There was no association between clutch size and cooperative breeding in a sample of 93 pairs. The results support the facilitating effect of high annual survival on the evolution of cooperative breeding in birds but the effect on clutch size remains elusive. PMID:24898375

  18. Water cooled breeder program summary report (LWBR (Light Water Breeder Reactor) development program)

    SciTech Connect

    Not Available

    1987-10-01

    The purpose of the Department of Energy Water Cooled Breeder Program was to demonstrate pratical breeding in a uranium-233/thorium fueled core while producing electrical energy in a commercial water reactor generating station. A demonstration Light Water Breeder Reactor (LWBR) was successfully operated for more than 29,000 effective full power hours in the Shippingport Atomic Power Station. The reactor operated with an availability factor of 76% and had a gross electrical output of 2,128,943,470 kilowatt hours. Following operation, the expended core was examined and no evidence of any fuel element defects was found. Nondestructive assay of 524 fuel rods determined that 1.39 percent more fissile fuel was present at the end of core life than at the beginning, proving that breeding had occurred. This demonstrates the existence of a vast source of electrical energy using plentiful domestic thorium potentially capable of supplying the entire national need for many centuries. To build on the successful design and operation of the Shippingport Breeder Core and to provide the technology to implement this concept, several reactor designs of large breeders and prebreeders were developed for commercial-sized plants of 900--1000 Mw(e) net. This report summarizes the Water Cooled Breeder Program from its inception in 1965 to its completion in 1987. Four hundred thirty-six technical reports are referenced which document the work conducted as part of this program. This work demonstrated that the Light Water Breeder Reactor is a viable alternative as a PWR replacement in the next generation of nuclear reactors. This transition would only require a minimum of change in design and fabrication of the reactor and operation of the plant.

  19. ORIGEN2 model and results for the Clinch River Breeder Reactor

    SciTech Connect

    Croff, A G; Bjerke, M A

    1982-06-01

    Reactor physics calculations and literature information acquisition have led to the development of a Clinch River Breeder Reactor (CRBR) model for the ORIGEN2 computer code. The model is based on cross sections taken directly from physics codes. Details are presented concerning the physical description of the fuel assemblies, the fuel management scheme, irradiation parameters, and initial material compositions. The ORIGEN2 model for the CRBR has been implemented, resulting in the production of graphical and tabular characteristics (radioactivity, thermal power, and toxicity) of CRBR spent fuel, high-level waste, and fuel-assembly structural material waste as a function of decay time. Characteristics for pressurized water reactors (PWRs), commercial liquid-metal fast breeder reactors (LMFBRs), and the Fast Flux Test Facility (FFTF) have also been included in this report for comparison with the CRBR data.

  20. Uranium resources and their implications for fission breeder and fusion hybrid development

    SciTech Connect

    Max, C.E.

    1984-05-15

    Present estimates of uranium resources and reserves in the US and the non-Communist world are reviewed. The resulting implications are considered for two proposed breeder technologies: the liquid metal fast breeder reactor (LMFBR) and the fusion hybrid reactor. Using both simple arguments and detailed scenarios from the published literature, conditions are explored under which the LMFBR and fusion hybrid could respectively have the most impact, considering both fuel-supply and economic factors. The conclusions emphasize strong potential advantages of the fusion hybrid, due to its inherently large breeding rate. A discussion is presented of proposed US development strategies for the fusion hybrid, which at present is far behind the LMFBR in its practical application and maturity.

  1. Shutdown and Closure of the Experimental Breeder Reactor - II

    SciTech Connect

    Michelbacher, John A.; Baily, Carl E.; Baird, Daniel K.; Henslee, S. Paul; Knight, Collin J.; Rosenberg, Kenneth E.

    2002-07-01

    The Department of Energy mandated the termination of the Integral Fast Reactor (IFR) Program, effective October 1, 1994. To comply with this decision, Argonne National Laboratory-West (ANL-W) prepared a plan providing detailed requirements to maintain the Experimental Breeder Reactor - II (EBR-II) in a radiologically and industrially safe condition, including removal of all irradiated fuel assemblies from the reactor plant, and removal and stabilization of the primary and secondary sodium, a liquid metal used to transfer heat within the reactor plant. The EBR-II is a pool-type reactor. The primary system contained approximately 325 m{sup 3} (86,000 gallons) of sodium and the secondary system contained 50 m{sup 3} (13,000 gallons). In order to properly dispose of the sodium in compliance with the Resource Conservation and Recovery Act (RCRA), a facility was built to react the sodium to a solid sodium hydroxide monolith for burial as a low level waste in a land disposal facility. Deactivation of a liquid metal fast breeder reactor (LMFBR) presents unique concerns. Residual amounts of sodium remaining in circuits and components must be passivated, inerted, or removed to preclude future concerns with sodium-air reactions that could generate potentially explosive mixtures of hydrogen and leave corrosive compounds. The passivation process being implemented utilizes a moist carbon dioxide gas that generates a passive layer of sodium carbonate/sodium bicarbonate over any quantities of residual sodium. Tests being conducted will determine the maximum depths of sodium that can be reacted using this method, defining the amount that must be dealt with later to achieve RCRA clean closure. Deactivation of the EBR-II complex is on schedule for a March, 2002, completion. Each system associated with EBR-II has an associated lay-up plan defining the system end state, as well as instructions for achieving the lay-up condition. A goal of system-by-system lay-up is to minimize

  2. Shutdown and closure of the experimental breeder reactor - II.

    SciTech Connect

    Michelbacher, J. A.; Baily, C. E.; Baird, D. K.; Henslee, S. P.; Knight, C. J.; Rosenberg, K. E.

    2002-09-26

    The Department of Energy mandated the termination of the Integral Fast Reactor (IFR) Program, effective October 1, 1994. To comply with this decision, Argonne National Laboratory-West (ANL-W) prepared a plan providing detailed requirements to maintain the Experimental Breeder Reactor-II (EBR-II) in a radiologically and industrially safe condition, including removal of all irradiated fuel assemblies from the reactor plant, and removal and stabilization of the primary and secondary sodium, a liquid metal used to transfer heat within the reactor plant. The EBR-II is a pool-type reactor. The primary system contained approximately 325 m{sup 3} (86,000 gallons) of sodium and the secondary system contained 50 m{sub 3} (13,000 gallons). In order to properly dispose of the sodium in compliance with the Resource Conservation and Recovery Act (RCRA), a facility was built to react the sodium to a solid sodium hydroxide monolith for burial as a low level waste in a land disposal facility. Deactivation of a liquid metal fast breeder reactor (LMFBR) presents unique concerns. Residual amounts of sodium remaining in circuits and components must be passivated, inerted, or removed to preclude future concerns with sodium-air reactions that could generate potentially explosive mixtures of hydrogen and leave corrosive compounds. The passivation process being implemented utilizes a moist carbon dioxide gas that generates a passive layer of sodium carbonate/sodium bicarbonate over any quantities of residual sodium. Tests being conducted will determine the maximum depths of sodium that can be reacted using this method, defining the amount that must be dealt with later to achieve RCRA clean closure. Deactivation of the EBR-II complex is on schedule for a March, 2002, completion. Each system associated with EBR-II has an associated layup plan defining the system end state, as well as instructions for achieving the layup condition. A goal of system-by-system layup is to minimize surveillance

  3. Superphenix: Is the fast breeder dream over -- or over yonder?

    SciTech Connect

    1997-03-01

    A detailed history of France`s Superphenix commercial fast breeder reactor project is presented. Important project milestones are discussed from the project`s conception in 1971 to its current status. Recommendations of the Castaing Commission on the project and future plans for use of the reactor are outlined. In addition, world wide fast breeder projects are listed and discussed.

  4. Development of advanced tritium breeders and neutron multipliers for DEMO solid breeder blankets

    NASA Astrophysics Data System (ADS)

    Tsuchiya, K.; Hoshino, T.; Kawamura, H.; Mishima, Y.; Yoshida, N.; Terai, T.; Tanaka, S.; Munakata, K.; Kato, S.; Uchida, M.; Nakamichi, M.; Yamada, H.; Yamaki, D.; Hayashi, K.

    2007-09-01

    In efforts to develop advanced tritium breeders, the effects of additives to lithium titanate (Li2TiO3) have been investigated, and good prospects have been obtained by using oxide additives such as TiO2, CaO and Li2O. As for the neutron multiplier, the development of a real-size electrode fabrication technique and the characterization of beryllium-based intermetallic compounds such as Be-Ti and Be-V have been performed. Properties of Be-Ti alloys have been found to be better than those of beryllium metal. In particular, steam interaction of a Be-Ti alloy was about 1/1000 as small as that of beryllium metal. These activities have led to bright prospects for the realization of the water-cooled DEMO breeder blanket by application of these advanced materials.

  5. US solid breeder blanket design for ITER

    SciTech Connect

    Gohar, Y.; Attaya, H.; Billone, M.; Lin, C.; Johnson, C.; Majumdar, S.; Smith, D. ); Goranson, P.; Nelson, B.; Williamson, D.; Baker, C. ); Raffray, A.; Badawi, A.; Gorbis, Z.; Ying, A.; Abdou, M. ); Sviatoslavsky, I.; Blanchard, J.; Mogahed, E.; Sawan, M.; Kulcinski, G. )

    1990-09-01

    The US blanket design activity has focused on the developments and the analyses of a solid breeder blanket concept for ITER. The main function of this blanket is to produce the necessary tritium required for the ITER operation and the test program. Safety, power reactor relevance, low tritium inventory, and design flexibility are the main reasons for the blanket selection. The blanket is designed to operate satisfactorily in the physics and the technology phases of ITER without the need for hardware changes. Mechanical simplicity, predictability, performance, minimum cost, and minimum R D requirements are the other criteria used to guide the design process. The design aspects of the blanket are summarized in this paper. 2 refs., 7 figs., 3 tabs.

  6. Lithium reprocessing technology for ceramic breeders

    NASA Astrophysics Data System (ADS)

    Tsuchiya, Kunihiko; Kawamura, Hiroshi; Saito, Minoru; Tatenuma, Katuyashi; Kainose, Mitsuru

    1995-03-01

    Lithium ceramics have been receiving considerable attention as tritium breeding materials for fusion reactors. Reprocessing technology development for these materials is proposed to recover lithium, as an effective use of resources and to remove radioactive isotopes. Four potential ceramic breeders (Li 2O, LiAlO 2, Li 2ZrO 3 and Li 4SiO 4) were prepared in order to estimate their dissolution properties in water and various acids (HCl, HNO 3, H 2SO 4, HF and aqua regia). The dissolution rates were determined by comparing the weight of the residue with that of the starting powder (the weight method). Recovery properties of lithium were examined by the precipitation method.

  7. Wireless, in-vessel neutron monitor for initial core-loading of advanced breeder reactors

    NASA Technical Reports Server (NTRS)

    Delorenzo, J. T.; Kennedy, E. J.; Blalock, T. V.; Rochelle, J. M.; Chiles, M. M.; Valentine, K. H.

    1981-01-01

    An experimental wireless, in-vessel neutron monitor was developed to measure the reactivity of an advanced breeder reactor as the core is loaded for the first time to preclude an accidental critically incident. The environment is liquid sodium at a temperature of approx. 220 C, with negligible gamma or neutron radiation. With ultrasonic transmission of neutron data, no fundamental limitation was observed after tests at 230 C for 2000 h. The neutron sensitivity was approx. 1 count/s-nv, and the potential data transmission rate was approx. 10,000 counts/s.

  8. Pressure drop considerations of a lithium cooled fusion breeder tokamak reactor blanket

    SciTech Connect

    Wong, C.P.C.

    1983-12-06

    Liquid lithium was selected as one of the coolants for the 1983 fusion breeder blanket used on the magnetically confined tokamak fusion reactor, and as a result, the thermal-hydraulic calculations were dominated by magnetohydrodynamic (MHD) considerations. The applicable sets of MHD equations for the engineering thermal-hydraulic design were reviewed and compared. Special attention was given to the MHD calculations for the fertile material zone, a packed bed of composite beryllium and thorium balls, since this region can dominate the thermal-hydraulic behavior of this blanket module. To keep the pressure drops acceptable, fertile fuel balls were omitted in the inboard blanket.

  9. Recommended practices in elevated temperature design: A compendium of breeder reactor experiences (1970-1986): An overview

    SciTech Connect

    Wei, B.C.; Cooper, W.L. Jr.; Dhalla, A.K.

    1987-09-01

    Significant experiences have been accumulated in the establishment of design methods and criteria applicable to the design of Liquid Metal Fast Breeder Reactor (LMFBR) components. The Subcommittee of the Elevated Temperature Design under the Pressure Vessel Research Council (PVRC) has undertaken to collect, on an international basis, design experience gained, and the lessons learned, to provide guidelines for next generation advanced reactor designs. This paper shall present an overview and describe the highlights of the work.

  10. Beam injection improvement for electron cyclotron resonance charge breeders

    SciTech Connect

    Lamy, T.; Angot, J.; Sortais, P.; Thuillier, T.

    2012-02-15

    The injection of a 1+ beam into an electron cyclotron resonance (ECR) charge breeder is classically performed through a grounded tube placed on its axis at the injection side. This tube presents various disadvantages for the operation of an ECR charge breeder. First experiments without a grounded tube show a better use of the microwave power and a better charge breeding efficiency. The optical acceptance of the charge breeder without decelerating tube allows the injection of high intensity 1+ ion beams at high energy, allowing metals sputtering inside the ion source. The use of this method for refractory metallic ion beams production is evaluated.

  11. The impact of recent innovations in the use of liquid chromatography-mass spectrometry in support of drug metabolism studies: are we all the way there yet?

    PubMed

    Nassar, Alaa-Eldin F; Talaat, Rasmy E; Kamel, Amin M

    2006-01-01

    Absorption, distribution, metabolism, excretion and toxicology (ADMET) studies are widely used in drug discovery and development to help obtain the optimal balance of properties necessary to convert lead compounds into drugs that are safe and effective for human use. Drug discovery efforts have been aimed at identifying and addressing metabolism issues at the earliest possible stage, by developing and applying innovative liquid chromatography-mass spectrometry (LC-MS)-based techniques and instrumentation, which are both faster and more accurate than prior techniques. Such new approaches are demonstrating considerable potential to improve the overall safety profile of drug candidates throughout the drug discovery and development process. These emerging techniques streamline and accelerate the process by eliminating potentially harmful candidates earlier and improving the safety of new drugs. In the area of drug metabolism, for example, revolutionary changes have been achieved by the combination of LC-MS with innovative instrumentation such as triple quadrupoles, ion traps and time-of-flight mass spectrometry. In turn, most ADMET studies have come to rely on LC-MS for the analysis of an ever-increasing workload of potential candidates. This article provides a discussion on the importance of LC-MS in supporting drug metabolism studies, and highlights the relative merits of current applications for LC-MS in drug metabolism testing and analysis. These applications include in vitro and in vivo testing, pharmacokinetic profiling, chiral separations, stable isotope labeling, metabolic activation testing, metabolite characterization and radiolabeled-drug testing. PMID:16445118

  12. Fabrication, properties, and tritium recovery from solid breeder materials

    SciTech Connect

    Johnson, C.E. ); Kondo, T. ); Roux, N. ); Tanaka, S. ); Vollath, D. )

    1991-01-01

    The breeding blanket is a key component of the fusion reactor because it directly involves tritium breeding and energy extraction, both of which are critical to development of fusion power. The lithium ceramics continue to show promise as candidate breeder materials. This promise was recognized by the International Thermonuclear Experimental Reactor (ITER) design team in its selection of ceramics as the first option for the ITER breeder material. Blanket design studies have indicated properties in the candidate materials data base that need further investigation. Current studies are focusing on tritium release behavior at high burnup, changes in thermophysical properties with burnup, compatibility between the ceramic breeder and beryllium multiplier, and phase changes with burnup. Laboratory and in-reactor tests, some as part of an international collaboration for development of ceramic breeder materials, are underway. 133 refs., 1 fig.

  13. Analysis of UF6 breeder reactor power plants

    NASA Technical Reports Server (NTRS)

    Clement, J. D.; Rust, J. H.

    1976-01-01

    Gaseous UF6 fueled breeder reactor design and technical applications of such concepts are summarized. Special attention was given to application in nuclear power plants and to reactor efficiency and safety factors.

  14. Advantages of liquid fluoride thorium reactor in comparison with light water reactor

    NASA Astrophysics Data System (ADS)

    Bahri, Che Nor Aniza Che Zainul; Majid, Amran Ab.; Al-Areqi, Wadeeah M.

    2015-04-01

    Liquid Fluoride Thorium Reactor (LFTR) is an innovative design for the thermal breeder reactor that has important potential benefits over the traditional reactor design. LFTR is fluoride based liquid fuel, that use the thorium dissolved in salt mixture of lithium fluoride and beryllium fluoride. Therefore, LFTR technology is fundamentally different from the solid fuel technology currently in use. Although the traditional nuclear reactor technology has been proven, it has perceptual problems with safety and nuclear waste products. The aim of this paper is to discuss the potential advantages of LFTR in three aspects such as safety, fuel efficiency and nuclear waste as an alternative energy generator in the future. Comparisons between LFTR and Light Water Reactor (LWR), on general principles of fuel cycle, resource availability, radiotoxicity and nuclear weapon proliferation shall be elaborated.

  15. Advantages of liquid fluoride thorium reactor in comparison with light water reactor

    SciTech Connect

    Bahri, Che Nor Aniza Che Zainul Majid, Amran Ab.; Al-Areqi, Wadeeah M.

    2015-04-29

    Liquid Fluoride Thorium Reactor (LFTR) is an innovative design for the thermal breeder reactor that has important potential benefits over the traditional reactor design. LFTR is fluoride based liquid fuel, that use the thorium dissolved in salt mixture of lithium fluoride and beryllium fluoride. Therefore, LFTR technology is fundamentally different from the solid fuel technology currently in use. Although the traditional nuclear reactor technology has been proven, it has perceptual problems with safety and nuclear waste products. The aim of this paper is to discuss the potential advantages of LFTR in three aspects such as safety, fuel efficiency and nuclear waste as an alternative energy generator in the future. Comparisons between LFTR and Light Water Reactor (LWR), on general principles of fuel cycle, resource availability, radiotoxicity and nuclear weapon proliferation shall be elaborated.

  16. Tritium percolation, convection, and permeation in fusion solid breeder blankets

    SciTech Connect

    Billone, M.C.; Liu, Y.Y.

    1985-01-01

    Models are developed to describe the percolation of released tritium through the breeder interconnected porosity to the purge stream, convection of tritium by the helium purge stream, and leakage or permeation of tritium through the structural material to the primary coolant system. Important parameters in the models are tritium generation rate, breeder microstructure, tritium species in the gas phase, temperatures, tritium diffusivities and permeabilities, and effectiveness of oxide barriers.

  17. Lithium mass transport in ceramic breeder materials

    SciTech Connect

    Blackburn, P.E.; Johnson, C.E.

    1990-01-01

    The objective of this activity is to measure the lithium vaporization from lithium oxide breeder material under differing temperature and moisture partial pressure conditions. Lithium ceramics are being investigated for use as tritium breeding materials. The lithium is readily converted to tritium after reacting with a neutron. With the addition of 1000 ppM H{sub 2} to the He purge gas, the bred tritium is readily recovered from the blanket as HT and HTO above 400{degree}C. Within the solid, tritium may also be found as LiOT which may transport lithium to cooler parts of the blanket. The pressure of LiOT(g), HTO(g), or T{sub 2}O(g) above Li{sub 2}O(s) is the same as that for reactions involving hydrogen. In our experiments we were limited to the use of hydrogen. The purpose of this work is to investigate the transport of LiOH(g) from the blanket material. 8 refs., 1 fig., 3 tabs.

  18. Ceramic breeder materials : status and needs.

    SciTech Connect

    Johnson, C.E.

    1998-02-02

    The tritium breeding blanket is one of the most important components of a fusion reactor because it directly involves both energy extraction and tritium production, both of which are critical to fusion power. Because of their overall desirable properties, lithium-containing ceramic solids are recognized as attractive tritium breeding materials for fusion reactor blankets. Indeed, their inherent thermal stability and chemical inertness are significant safety advantages. In numerous in-pile experiments, these materials have performed well, showing good thermal stability and good tritium release characteristics. Tritium release is particularly facile when an argon or helium purge gas containing hydrogen, typically at levels of about 0.1%, is used. However, the addition of hydrogen to the purge gas imposes a penalty when it comes to recovery of the tritium produced in the blanket. In particular, a large amount of hydrogen in the purge gas will necessitate a large multiple-stage tritium purification unit, which could translate into higher costs. Optimizing tritium release while minimizing the amount of hydrogen necessary in the purge gas requires a deeper understanding of the tritium release process, especially the interactions of hydrogen with the surface of the lithium ceramic. This paper reviews the status of ceramic breeder research and highlights several issues and data needs.

  19. Fusion breeder: its potential role and prospects

    SciTech Connect

    Lee, J.D.

    1981-01-01

    The fusion breeder is a concept that utilizes 14 MeV neutrons from D + T ..-->.. n(14.1 MeV) + ..cap alpha..(3.5 MeV) fusion reactions to produce more fuel than the tritium (T) needed to sustain the fusion process. This excess fuel production capacity is used to produce fissile material (Pu-239 or U-233) for subsequent use in fission reactors. We are concentrating on a class of blankets we call fission suppressed. The blanket is the region surrounding the fusion plasma in which fusion neutrons interact to produce fuel and heat. The fission-suppressed blanket uses non-fission reactions (mainly (n,2n) or (n,n't)) to generate excess neutrons for the production of net fuel. This is in contrast to the fast fission class of blankets which use (n,fiss) reactions to generate excess neutrons. Fusion reactors with fast fission blankets are commony known as fusion-fission hybrids because they combine fusion and fission in the same device.

  20. System seismic analysis of an innovative primary system for a large pool type LMFBR plant

    SciTech Connect

    Pan, Y.C.; Wu, T.S.; Cha, B.K.; Burelbach, J.; Seidensticker, R.

    1984-01-01

    The system seismic analysis of an innovative primary system for a large pool type liquid metal fast breeder reactor (LMFBR) plant is presented. In this primary system, the reactor core is supported in a way which differs significantly from that used in previous designs. The analytical model developed for this study is a three-dimensional finite element model including one-half of the primary system cut along the plane of symmetry. The model includes the deck and deck mounted components,the reactor vessel, the core support structure, the core barrel, the radial neutron shield, the redan, and the conical support skirt. The sodium contained in the primary system is treated as a lumped mass appropriately distributed among various components. The significant seismic behavior as well as the advantages of this primary system design are discussed in detail.

  1. Development of electron beam ion source charge breeder for rare isotopes at Californium Rare Isotope Breeder Upgrade

    SciTech Connect

    Kondrashev, S.; Dickerson, C.; Levand, A.; Ostroumov, P. N.; Pardo, R. C.; Savard, G.; Vondrasek, R.; Alessi, J.; Beebe, E.; Pikin, A.; Kuznetsov, G. I.; Batazova, M. A.

    2012-02-15

    Recently, the Californium Rare Isotope Breeder Upgrade (CARIBU) to the Argonne Tandem Linac Accelerator System (ATLAS) was commissioned and became available for production of rare isotopes. Currently, an electron cyclotron resonance ion source is used as a charge breeder for CARIBU beams. To further increase the intensity and improve the purity of neutron-rich ion beams accelerated by ATLAS, we are developing a high-efficiency charge breeder for CARIBU based on an electron beam ion source (EBIS). The CARIBU EBIS charge breeder will utilize the state-of-the-art EBIS technology recently developed at Brookhaven National Laboratory (BNL). The electron beam current density in the CARIBU EBIS trap will be significantly higher than that in existing operational charge-state breeders based on the EBIS concept. The design of the CARIBU EBIS charge breeder is nearly complete. Long-lead components of the EBIS such as a 6-T superconducting solenoid and an electron gun have been ordered with the delivery schedule in the fall of 2011. Measurements of expected breeding efficiency using the BNL Test EBIS have been performed using a Cs{sup +} surface ionization ion source for external injection in pulsed mode. In these experiments we have achieved {approx}70% injection/extraction efficiency and breeding efficiency into the most abundant charge state of {approx}17%.

  2. Development of electron beam ion source charge breeder for rare isotopes at Californium Rare Isotope Breeder Upgrade

    SciTech Connect

    Kondrashev S.; Alessi J.; Dickerson, C.; Levand, A.; Ostroumov, P.N.; Pardo, R.C.; Savard, G.; Vondrasek, R.; Beebe, E.; Pikin, A.; Kuznetsov, G.I.; Batazova, M.A.

    2012-02-03

    Recently, the Californium Rare Isotope Breeder Upgrade (CARIBU) to the Argonne Tandem Linac Accelerator System (ATLAS) was commissioned and became available for production of rare isotopes. Currently, an electron cyclotron resonance ion source is used as a charge breeder for CARIBU beams. To further increase the intensity and improve the purity of neutron-rich ion beams accelerated by ATLAS, we are developing a high-efficiency charge breeder for CARIBU based on an electron beam ion source (EBIS). The CARIBU EBIS charge breeder will utilize the state-of-the-art EBIS technology recently developed at Brookhaven National Laboratory (BNL). The electron beam current density in the CARIBU EBIS trap will be significantly higher than that in existing operational charge-state breeders based on the EBIS concept. The design of the CARIBU EBIS charge breeder is nearly complete. Long-lead components of the EBIS such as a 6-T superconducting solenoid and an electron gun have been ordered with the delivery schedule in the fall of 2011. Measurements of expected breeding efficiency using the BNL Test EBIS have been performed using a Cs{sup +} surface ionization ion source for external injection in pulsed mode. In these experiments we have achieved {approx}70% injection/extraction efficiency and breeding efficiency into the most abundant charge state of {approx}17%.

  3. Multiple breeders, breeder shifts and inclusive fitness returns in an ant

    PubMed Central

    Bargum, Katja; Sundström, Liselotte

    2007-01-01

    In social insects, colonies may contain multiple reproductively active queens. This leads to potential conflicts over the apportionment of brood maternity, especially with respect to the production of reproductive offspring. We investigated reproductive partitioning in offspring females (gynes) and workers in the ant Formica fusca, and combined this information with data on the genetic returns gained by workers. Our results provide the first evidence that differential reproductive partitioning among breeders can enhance the inclusive fitness returns for sterile individuals that tend non-descendant offspring. Two aspects of reproductive partitioning contribute to this outcome. First, significantly fewer mother queens contribute to gyne (new reproductive females) than to worker brood, such that relatedness increases from worker to gyne brood. Second, and more importantly, adult workers were significantly more related to the reproductive brood raised by the colony, than to the contemporary worker brood. Thus, the observed breeder shift leads to genetic benefits for the adult workers that tend the brood. Our results also have repercussions for genetic population analyses. Given the observed pattern of reproductive partitioning, estimates of effective population size based on worker and gyne samples are not interchangeable. PMID:17439857

  4. Fast and efficient charge breeding of the Californium rare isotope breeder upgrade electron beam ion source

    DOE PAGESBeta

    Ostroumov, P. N.; Barcikowski, A.; Dickerson, C. A.; Perry, A.; Pikin, A. I.; Sharamentov, S. I.; Vondrasek, R. C.; Zinkann, G. P.

    2015-08-28

    The Electron Beam Ion Source (EBIS), developed to breed Californium Rare Isotope Breeder Upgrade (CARIBU) radioactive beams at Argonne Tandem Linac Accelerator System (ATLAS), is being tested off-line. A unique property of the EBIS is a combination of short breeding times, high repetition rates, and a large acceptance. Overall, we have implemented many innovative features during the design and construction of the CARIBU EBIS as compared to the existing EBIS breeders. The off-line charge breeding tests are being performed using a surface ionization source that produces singly charged cesium ions. The main goal of the off-line commissioning is to demonstratemore » stable operation of the EBIS at a 10 Hz repetition rate and a breeding efficiency into single charge state higher than 15%. These goals have been successfully achieved and exceeded. We have measured (20% ± 0.7%) breeding efficiency into the single charge state of 28+ cesium ions with the breeding time of 28 ms. In general, the current CARIBU EBIS operational parameters can provide charge breeding of any ions in the full mass range of periodic table with high efficiency, short breeding times, and sufficiently low charge-to-mass ratio, 1/6.3 for the heaviest masses, for further acceleration in ATLAS. In this study, we discuss the parameters of the EBIS and the charge breeding results in a pulsed injection mode with repetition rates up to 10 Hz.« less

  5. Fast and efficient charge breeding of the Californium rare isotope breeder upgrade electron beam ion source

    SciTech Connect

    Ostroumov, P. N. Barcikowski, A.; Dickerson, C. A.; Perry, A.; Sharamentov, S. I.; Vondrasek, R. C.; Zinkann, G. P.; Pikin, A. I.

    2015-08-15

    The Electron Beam Ion Source (EBIS), developed to breed Californium Rare Isotope Breeder Upgrade (CARIBU) radioactive beams at Argonne Tandem Linac Accelerator System (ATLAS), is being tested off-line. A unique property of the EBIS is a combination of short breeding times, high repetition rates, and a large acceptance. Overall, we have implemented many innovative features during the design and construction of the CARIBU EBIS as compared to the existing EBIS breeders. The off-line charge breeding tests are being performed using a surface ionization source that produces singly charged cesium ions. The main goal of the off-line commissioning is to demonstrate stable operation of the EBIS at a 10 Hz repetition rate and a breeding efficiency into single charge state higher than 15%. These goals have been successfully achieved and exceeded. We have measured (20% ± 0.7%) breeding efficiency into the single charge state of 28+ cesium ions with the breeding time of 28 ms. In general, the current CARIBU EBIS operational parameters can provide charge breeding of any ions in the full mass range of periodic table with high efficiency, short breeding times, and sufficiently low charge-to-mass ratio, 1/6.3 for the heaviest masses, for further acceleration in ATLAS. In this paper, we discuss the parameters of the EBIS and the charge breeding results in a pulsed injection mode with repetition rates up to 10 Hz.

  6. Fast and efficient charge breeding of the Californium rare isotope breeder upgrade electron beam ion source.

    PubMed

    Ostroumov, P N; Barcikowski, A; Dickerson, C A; Perry, A; Pikin, A I; Sharamentov, S I; Vondrasek, R C; Zinkann, G P

    2015-08-01

    The Electron Beam Ion Source (EBIS), developed to breed Californium Rare Isotope Breeder Upgrade (CARIBU) radioactive beams at Argonne Tandem Linac Accelerator System (ATLAS), is being tested off-line. A unique property of the EBIS is a combination of short breeding times, high repetition rates, and a large acceptance. Overall, we have implemented many innovative features during the design and construction of the CARIBU EBIS as compared to the existing EBIS breeders. The off-line charge breeding tests are being performed using a surface ionization source that produces singly charged cesium ions. The main goal of the off-line commissioning is to demonstrate stable operation of the EBIS at a 10 Hz repetition rate and a breeding efficiency into single charge state higher than 15%. These goals have been successfully achieved and exceeded. We have measured (20% ± 0.7%) breeding efficiency into the single charge state of 28+ cesium ions with the breeding time of 28 ms. In general, the current CARIBU EBIS operational parameters can provide charge breeding of any ions in the full mass range of periodic table with high efficiency, short breeding times, and sufficiently low charge-to-mass ratio, 1/6.3 for the heaviest masses, for further acceleration in ATLAS. In this paper, we discuss the parameters of the EBIS and the charge breeding results in a pulsed injection mode with repetition rates up to 10 Hz. PMID:26329185

  7. Fast and efficient charge breeding of the Californium rare isotope breeder upgrade electron beam ion source

    SciTech Connect

    Ostroumov, P. N.; Barcikowski, A.; Dickerson, C. A.; Perry, A.; Pikin, A. I.; Sharamentov, S. I.; Vondrasek, R. C.; Zinkann, G. P.

    2015-08-28

    The Electron Beam Ion Source (EBIS), developed to breed Californium Rare Isotope Breeder Upgrade (CARIBU) radioactive beams at Argonne Tandem Linac Accelerator System (ATLAS), is being tested off-line. A unique property of the EBIS is a combination of short breeding times, high repetition rates, and a large acceptance. Overall, we have implemented many innovative features during the design and construction of the CARIBU EBIS as compared to the existing EBIS breeders. The off-line charge breeding tests are being performed using a surface ionization source that produces singly charged cesium ions. The main goal of the off-line commissioning is to demonstrate stable operation of the EBIS at a 10 Hz repetition rate and a breeding efficiency into single charge state higher than 15%. These goals have been successfully achieved and exceeded. We have measured (20% ± 0.7%) breeding efficiency into the single charge state of 28+ cesium ions with the breeding time of 28 ms. In general, the current CARIBU EBIS operational parameters can provide charge breeding of any ions in the full mass range of periodic table with high efficiency, short breeding times, and sufficiently low charge-to-mass ratio, 1/6.3 for the heaviest masses, for further acceleration in ATLAS. In this study, we discuss the parameters of the EBIS and the charge breeding results in a pulsed injection mode with repetition rates up to 10 Hz.

  8. Fast and efficient charge breeding of the Californium rare isotope breeder upgrade electron beam ion source

    NASA Astrophysics Data System (ADS)

    Ostroumov, P. N.; Barcikowski, A.; Dickerson, C. A.; Perry, A.; Pikin, A. I.; Sharamentov, S. I.; Vondrasek, R. C.; Zinkann, G. P.

    2015-08-01

    The Electron Beam Ion Source (EBIS), developed to breed Californium Rare Isotope Breeder Upgrade (CARIBU) radioactive beams at Argonne Tandem Linac Accelerator System (ATLAS), is being tested off-line. A unique property of the EBIS is a combination of short breeding times, high repetition rates, and a large acceptance. Overall, we have implemented many innovative features during the design and construction of the CARIBU EBIS as compared to the existing EBIS breeders. The off-line charge breeding tests are being performed using a surface ionization source that produces singly charged cesium ions. The main goal of the off-line commissioning is to demonstrate stable operation of the EBIS at a 10 Hz repetition rate and a breeding efficiency into single charge state higher than 15%. These goals have been successfully achieved and exceeded. We have measured (20% ± 0.7%) breeding efficiency into the single charge state of 28+ cesium ions with the breeding time of 28 ms. In general, the current CARIBU EBIS operational parameters can provide charge breeding of any ions in the full mass range of periodic table with high efficiency, short breeding times, and sufficiently low charge-to-mass ratio, 1/6.3 for the heaviest masses, for further acceleration in ATLAS. In this paper, we discuss the parameters of the EBIS and the charge breeding results in a pulsed injection mode with repetition rates up to 10 Hz.

  9. Effect of Lithium Enrichment on the Tritium Breeding Characteristics of Various Breeders in a Fusion Driven Hybrid Reactor

    NASA Astrophysics Data System (ADS)

    Übeyli, Mustafa

    2009-09-01

    Selection of lithium containing materials is very important in the design of a deuterium-tritium (DT) fusion driven hybrid reactor in order to supply its tritium self-sufficiency. Tritium, an artificial isotope of hydrogen, can be produced in the blanket by using the neutron capture reactions of lithium in the coolants and/or blanket materials which consist of lithium. This study presents the effect of lithium-6 enrichment in the coolant of the reactor on the tritium breeding of the hybrid blanket. Various liquid-solid breeder couples were investigated to determine the effective breeders. Numerical results pointed out that the tritium production increased with increasing lithium-6 enrichment for all cases.

  10. IEC-^3He Breeder for D-^3He Satellite Systems.

    NASA Astrophysics Data System (ADS)

    Chacon, L.; Miley, G. H.

    1996-11-01

    D-^3He fusion minimizes neutrons and maximizes charged fusion products, enabling increased energy recovery efficiency by direct conversion. However, scarce ^3He terrestrial resources have deterred R&D on this alternative. Here, we explore ^3He production through Inertial Electrostatic Confinement^1 (IEC) D-breeders, which supply ^3He to FRC D-^3He satellite reactors.^2 Favorable features for the IEC breeder include simplicity, low cost, easy extraction of fusion products, and compatibility with direct conversion. The breeder-satellite system energy balance is analyzed taking the net energy gain of the overall system, Q_N, as the figure of merit. Breeding is applicable for systems where the satellite Q-value, Q_S, > the breeder Q-value, Q_B. For improved performance, i.e., for high Q_N, QS >= QB >> 1 is needed; however, lower QB values (typical of the IEC) are permissible and still offer sufficient Q_N. An economic study determined breeding produces ^3He at a cost comparable to lunar ^3He, already shown to lead to competitive power.^3 The cost of electricity (COE) for the breeder-satellite complex was compared with the ARTEMIS COE,^4 using lunar ^3He fuel: assuming one satellite (1000 MWe)/breeder (170 MWe), the ratio of the breeding system COE to the lunar mining base COE is ~ 1.2. However, economic breeding is driven by large IEC breeder powers, i.e., increased ^3He breeding rates. Thus, the COE ratio approaches unity with two or three satellites/breeder, requiring increased breeder size and power (340 MWe for 2 satellites, 510 MWe for 3 satellites). Such systems potentially provide a ``bridge'' to a future lunar ^3He economy. 1. G.H. Miley et al., Dense Z-pinches, AIP Conf. 299, AIP Press, 675-689 (1994). 2. G.H. Miley, Nucl. Instrum. Methods, A271, 197-202 (1988). 3. L.J. Wittenberg et al., Fusion Technol., 10, 167-178 (1986). 4. H. Momota et al., Fusion Technol., 21, 2307-2323 (1992).

  11. Innovative application of ionic liquid to separate Al and cathode materials from spent high-power lithium-ion batteries.

    PubMed

    Zeng, Xianlai; Li, Jinhui

    2014-04-30

    Because of the increasing number of electric vehicles, there is an urgent need for effective recycling technologies to recapture the significant amount of valuable metals contained in spent lithium-ion batteries (LiBs). Previous studies have indicated, however, that Al and cathode materials were quite difficult to separate due to the strong binding force supplied by the polyvinylidene fluoride (PVDF), which was employed to bind cathode materials and Al foil. This research devoted to seek a new method of melting the PVDF binder with heated ionic liquid (IL) to separate Al foil and cathode materials from the spent high-power LiBs. Theoretical analysis based on Fourier's law was adopted to determine the heat transfer mechanism of cathode material and to examine the relationship between heating temperature and retention time. All the experimental and theoretic results show that peel-off rate of cathode materials from Al foil could reach 99% when major process parameters were controlled at 180°C heating temperature, 300 rpm agitator rotation, and 25 min retention time. The results further imply that the application of IL for recycling Al foil and cathode materials from spent high-power LiBs is highly efficient, regardless of the application source of the LiBs or the types of cathode material. This study endeavors to make a contribution to an environmentally sound and economically viable solution to the challenge of spent LiB recycling. PMID:24607415

  12. MOLTEN PLUTONIUM FUELED FAST BREEDER REACTOR

    DOEpatents

    Kiehn, R.M.; King, L.D.P.; Peterson, R.E.; Swickard, E.O. Jr.

    1962-06-26

    A description is given of a nuclear fast reactor fueled with molten plutonium containing about 20 kg of plutonium in a tantalum container, cooled by circulating liquid sodium at about 600 to 650 deg C, having a large negative temperature coefficient of reactivity, and control rods and movable reflector for criticality control. (AEC)

  13. Application OF LIBS To Estimate The Age Of Broiler Breeders

    NASA Astrophysics Data System (ADS)

    Salam, Z. Abdel; Harith, M. A.

    2011-09-01

    Laser Induced Breakdown Spectroscopy (LIBS) is a well-known spectrochemical elemental analysis technique. In our investigations of the LIBS spectra it has been found that there is a remarkable correlation between the ionic to atomic spectral lines emission ratio and the surface hardness of eggshell for two Different Broiler Breeder at different age. The proposed technique has been applied successfully in poultry science to estimate the age of broiler breeders by measuring the surface hardness of their eggshell. The experiments have been performed on two different strains, Arbor Acres plus (AAP) and Hubard Classic (HC), and the results were satisfactory.

  14. An Innovative Technique of Liquid Purity Analysis and Its Application to Analysis of Water Concentration in Alcohol-Water Mixtures and Studies on Change of Activation Energies of the Mixtures

    NASA Astrophysics Data System (ADS)

    de, Dilip; Aziz Dikko, Abdul

    2012-10-01

    The activation energy of a liquid molecule and hence its viscosity coefficient changes with addition of contaminants to the original liquid. This forms the basis of a new technology for analysis of purity of the liquid. We discovered that concentration of certain contaminants such as water in alcohol or vice versa can be uniquely and accurately determined in a short time (about 10-15 minutes) using a simple and yet innovative technique that only requires measurement of time of flow of the impure liquid (say, water-alcohol mixture) and distilled water through a simple viscometer designed and constructed for this purpose. We find that the viscosity coefficient μ of alcohol increased almost linearly with water concentration at a rate that depends on the type of alcohol and water concentration. We determined the increase of activation energy of alcohol molecules with increase of water concentration. This increase also depends on type of alcohol. Our detailed investigation on alcohol-water mixtures for both ethyl and methyl alcohol along with discussion on possible future potential application of such a simple, yet very reliable inexpensive technique for liquid purity analysis is presented. A comparison is made of our present method with other methods on the accuracies, problems and reliability of impurity analysis in liquids. A part of the quantum theory of viscosity of liquid mixtures that is in the developmental stage in order to explain some of the observed properties is presented.

  15. Nuclear breeder reactor fuel element with silicon carbide getter

    DOEpatents

    Christiansen, David W.; Karnesky, Richard A.

    1987-01-01

    An improved cesium getter 28 is provided in a breeder reactor fuel element or pin in the form of an extended surface area, low density element formed in one embodiment as a helically wound foil 30 located with silicon carbide, and located at the upper end of the fertile material upper blanket 20.

  16. Deployment Scenario of Heavy Water Cooled Thorium Breeder Reactor

    SciTech Connect

    Mardiansah, Deby; Takaki, Naoyuki

    2010-06-22

    Deployment scenario of heavy water cooled thorium breeder reactor has been studied. We have assumed to use plutonium and thorium oxide fuel in water cooled reactor to produce {sup 233}U which will be used in thorium breeder reactor. The objective is to analysis the potential of water cooled Th-Pu reactor for replacing all of current LWRs especially in Japan. In this paper, the standard Pressurize Water Reactor (PWR) has been designed to produce 3423 MWt; (i) Th-Pu PWR, (ii) Th-Pu HWR (MFR = 1.0) and (iii) Th-Pu HWR (MFR 1.2). The properties and performance of the core were investigated by using cell and core calculation code. Th-Pu PWR or HWR produces {sup 233}U to introduce thorium breeder reactor. The result showed that to replace all (60 GWe) LWR by thorium breeder reactor within a period of one century, Th-Pu oxide fueled PWR has insufficient capability to produce necessary amount of {sup 233}U and Th-Pu oxide fueled HWR has almost enough potential to produce {sup 233}U but shows positive void reactivity coefficient.

  17. Clinch River Breeder Reactor Plant Project: construction schedule

    SciTech Connect

    Purcell, W.J.; Martin, E.M.; Shivley, J.M.

    1982-01-01

    The construction schedule for the Clinch River Breeder Reactor Plant and its evolution are described. The initial schedule basis, changes necessitated by the evaluation of the overall plant design, and constructability improvements that have been effected to assure adherence to the schedule are presented. The schedule structure and hierarchy are discussed, as are tools used to define, develop, and evaluate the schedule.

  18. Fission-suppressed hybrid reactor: the fusion breeder

    SciTech Connect

    Moir, R.W.; Lee, J.D.; Coops, M.S.

    1982-12-01

    Results of a conceptual design study of a /sup 233/U-producing fusion breeder are presented. The majority of the study was devoted to conceptual design and evaluation of a fission-suppressed blanket and to fuel cycle issues such as fuel reprocessing, fuel handling, and fuel management. Studies in the areas of fusion engineering, reactor safety, and economics were also performed.

  19. Evaluation of tritium release properties of advanced tritium breeders

    SciTech Connect

    Hoshino, T.; Ochiai, K.; Edao, Y.; Kawamura, Y.

    2015-03-15

    Demonstration power plant (DEMO) fusion reactors require advanced tritium breeders with high thermal stability. Lithium titanate (Li{sub 2}TiO{sub 3}) advanced tritium breeders with excess Li (Li{sub 2+x}TiO{sub 3+y}) are stable in a reducing atmosphere at high temperatures. Although the tritium release properties of tritium breeders are documented in databases for DEMO blanket design, no in situ examination under fusion neutron (DT neutron) irradiation has been performed. In this study, a preliminary examination of the tritium release properties of advanced tritium breeders was performed, and DT neutron irradiation experiments were performed at the fusion neutronics source (FNS) facility in JAEA. Considering the tritium release characteristics, the optimum grain size after sintering is <5 μm. From the results of the optimization of granulation conditions, prototype Li{sub 2+x}TiO{sub 3+y} pebbles with optimum grain size (<5 μm) were successfully fabricated. The Li{sub 2+x}TiO{sub 3+y} pebbles exhibited good tritium release properties similar to the Li{sub 2}TiO{sub 3} pebbles. In particular, the released amount of HT gas for easier tritium handling was higher than that of HTO water. (authors)

  20. A fast and innovative microextraction technique, μSPEed, followed by ultrahigh performance liquid chromatography for the analysis of phenolic compounds in teas.

    PubMed

    Porto-Figueira, Priscilla; Figueira, José A; Pereira, Jorge A M; Câmara, José S

    2015-12-11

    The objective of this study was to evaluate the efficiency of a promising solid phase microextraction technique, μSPEed, in the analysis of selected phenolic compounds from teas by ultrahigh performance liquid chromatography with photodiode array detection (μSPEed/UHPLC-PDA). The innovative μSPEed configuration uses 3-μm sorbent particles tightly packed in a disposable needle equipped with a pressure-driven valve to withdraw samples in a single direction. The system was operated by the electronic pipette eVol® and different parameters influencing the extraction efficiency, as the nature of sorbent, pH, loading and elution conditions, and solvents were optimized. The best extracting conditions were obtained by loading twice 100μL of tea samples through the PS/DVB-RP sorbent and eluting with 50μL of acidified MeOH 95%. The following chromatographic separation was carried out in an Acquity C18 BEH capillary column using a gradient of 0.1% FA and acetonitrile. The optimized μSPEed/UHPLC-PDA methodology is selective and specific and was properly validated for 8 phenolic compounds widely reported in different teas. Overall, an excellent analytical performance was obtained in the 0.2-20μg/L linear dynamic range (LDR), with very low limits of detection (LODs) and quantification (LOQs), ranging between 3.5-16.8ng/mL and 10.6-50.6ng/mL, respectively, high recoveries (89.3-103.3%), good precision (RSD<5%) and negligible matrix effect. The methodology was used to assess the target polyphenols concentration in several tea samples. Rutin and quercetin-3-glucoside were the most abundant phenolics in all tea samples analysed and, with exception of naringenin and cinnamic acid, which are present in high amounts in the investigated citric teas, remain phenolic compounds are present in trace levels. PMID:26585207

  1. Fuel Summary Report: Shippingport Light Water Breeder Reactor - Rev. 2

    SciTech Connect

    Olson, Gail Lynn; Mc Cardell, Richard Keith; Illum, Douglas Brent

    2002-09-01

    The Shippingport Light Water Breeder Reactor (LWBR) was developed by Bettis Atomic Power Laboratory to demonstrate the potential of a water-cooled, thorium oxide fuel cycle breeder reactor. The LWBR core operated from 1977-82 without major incident. The fuel and fuel components suffered minimal damage during operation, and the reactor testing was deemed successful. Extensive destructive and nondestructive postirradiation examinations confirmed that the fuel was in good condition with minimal amounts of cladding deformities and fuel pellet cracks. Fuel was placed in wet storage upon arrival at the Expended Core Facility, then dried and sent to the Idaho Nuclear Technology and Engineering Center for underground dry storage. It is likely that the fuel remains in good condition at its current underground dry storage location at the Idaho Nuclear Technology and Engineering Center. Reports show no indication of damage to the core associated with shipping, loading, or storage.

  2. Role of the breeder in long-term energy economics

    SciTech Connect

    Kosobud, R.F.; Daly, T.A.; Chang, Y.I.

    1982-01-01

    Private and public decisions affecting the use of nuclear and other energy technologies over a long-run time horizon were studied using the ETA-MACRO model which provides for economic- and energy-sector interactions. The impact on the use of competing energy technologies of a public decision to apply benefit-cost analysis to the production of carbon dioxide that enters the atmosphere is considered. Assuming the public choice is to impose an appropriate penalty tax on those technologies which generate CO/sub 2/ and to allow decentralized private decisions to choose the optimal mix of energy technologies that maximize a nonlinear objective function subject to constraints, the study showed that breeder technology provides a much-larger share of domestically consumed energy. Having the breeder technology available as a substitute permits control of CO/sub 2/ without significant reductions in consumption or gross national product growth paths.

  3. Feasibility study on the thorium fueled boiling water breeder reactor

    SciTech Connect

    PetrusTakaki, N.

    2012-07-01

    The feasibility of (Th,U)O 2 fueled, boiling water breeder reactor based on conventional BWR technology has been studied. In order to determine the potential use of water cooled thorium reactor as a competitive breeder, this study evaluated criticality, breeding and void reactivity coefficient in response to changes made in MFR and fissile enrichments. The result of the study shows that while using light water as moderator, low moderator to fuel volume ratio (MFR=0.5), it was possible to breed fissile fuel in negative void reactivity condition. However the burnup value was lower than the value of the current LWR. On the other hand, heavy water cooled reactor shows relatively wider feasible breeding region, which lead into possibility of designing a core having better neutronic and economic performance than light water with negative void reactivity coefficient. (authors)

  4. Charge breeder for the SPIRAL1 upgrade: Preliminary results

    NASA Astrophysics Data System (ADS)

    Maunoury, L.; Delahaye, P.; Dubois, M.; Angot, J.; Sole, P.; Bajeat, O.; Barton, C.; Frigot, R.; Jeanne, A.; Jardin, P.; Kamalou, O.; Lecomte, P.; Osmond, B.; Peschard, G.; Lamy, T.; Savalle, A.

    2016-02-01

    In the framework of the SPIRAL1 upgrade under progress at the GANIL lab, the charge breeder based on a LPSC Phoenix ECRIS, first tested at ISOLDE has been modified to benefit of the last enhancements of this device from the 1+/n+ community. The modifications mainly concern the 1 + optics, vacuum techniques, and the RF—buffer gas injection into the charge breeder. Prior to its installation in the midst of the low energy beam line of the SPIRAL1 facility, it has been decided to qualify its performances and several operation modes at the test bench of LPSC lab. This contribution shall present preliminary results of experiments conducted at LPSC concerning the 1 + to n+ conversion efficiencies for noble gases as well as for alkali elements and the corresponding transformation times.

  5. Solid breeder/structure mechanical interaction and thermal stability

    SciTech Connect

    Liu, Y.Y.; Billone, M.C.; Taghavi, K.

    1985-04-01

    Solid breeder/structure mechanical interaction (BSMI) during fusion reactor blanket operation is a potential failure mode which could limit the lifetime of the blanket. The severity of BSMI will generally depend on the materials, specific blanket designs, and blanket operating conditions. Thermomechanical analyses performed for a helium-cooled blanket employing Li/sub 2/O/HT-9 plates indicate that BSMI could be a serious concern for this blanket.

  6. Reproduction responses of broiler-breeders to anticoccidial agents.

    PubMed

    Jones, J E; Solis, J; Hughes, B L; Castaldo, D J; Toler, J E

    1990-01-01

    Two experiments were conducted to determine the effects of anticoccidial agents on production and reproduction of broiler breeders. In Experiment 1, nicarbazin (NCZ) was fed at 20, 50, and 100 ppm. There was no depression in egg production, egg weight, or fertility from feeding these levels. As level of NCZ increased, there was a linear decrease in hatchability. The amount of 4,4'-dinitrocarbanilide (DNC) in the egg yolks increased linearly as the levels of NCZ went up; the degree of egg-shell depigmentation was directly related to the level of NCZ fed starting at 50 ppm. Experiment 2 utilized a different strain of broiler breeders. Halofuginone (3 ppm), maduramicin (5 ppm), monensin (100 ppm), narasin (70 ppm), NCZ (125 ppm), robenidine (33 ppm), and salinomycin (60 ppm) were fed to broiler breeders at the levels listed. Only NCZ reduced egg production. Narasin induced a reduction in egg weight. Both narasin and salinomycin caused a significant drop in hatchability. Feeding NCZ also induced a rapid and more severe decrease in hatchability. Monensin was the only anticoccidial agent that reduced fertility. Halofuginone, maduramicin, and robenidine had no biologically significant effect on henday production, egg weight, hatch of fertile eggs, or shell depigmentation. Feeding NCZ at 125 ppm caused a complete bleaching of brown-shell eggs by the 3rd consecutive day of treatment; but 7 days after NCZ was withdrawn from the feed, pigmentation returned to the pretreatment level. PMID:2320530

  7. Gas core reactors for actinide transmutation and breeder applications

    NASA Technical Reports Server (NTRS)

    Clement, J. D.; Rust, J. H.

    1978-01-01

    This work consists of design power plant studies for four types of reactor systems: uranium plasma core breeder, uranium plasma core actinide transmuter, UF6 breeder and UF6 actinide transmuter. The plasma core systems can be coupled to MHD generators to obtain high efficiency electrical power generation. A 1074 MWt UF6 breeder reactor was designed with a breeding ratio of 1.002 to guard against diversion of fuel. Using molten salt technology and a superheated steam cycle, an efficiency of 39.2% was obtained for the plant and the U233 inventory in the core and heat exchangers was limited to 105 Kg. It was found that the UF6 reactor can produce high fluxes (10 to the 14th power n/sq cm-sec) necessary for efficient burnup of actinide. However, the buildup of fissile isotopes posed severe heat transfer problems. Therefore, the flux in the actinide region must be decreased with time. Consequently, only beginning-of-life conditions were considered for the power plant design. A 577 MWt UF6 actinide transmutation reactor power plant was designed to operate with 39.3% efficiency and 102 Kg of U233 in the core and heat exchanger for beginning-of-life conditions.

  8. Operational experience with the Argonne National Laboratory Californium Rare Ion Breeder Upgrade facility and electron cyclotron resonance charge breeder

    NASA Astrophysics Data System (ADS)

    Vondrasek, R.; Clark, J.; Levand, A.; Palchan, T.; Pardo, R.; Savard, G.; Scott, R.

    2014-02-01

    The Californium Rare Ion Breeder Upgrade (CARIBU) of the Argonne National Laboratory Argonne Tandem Linac Accelerator System (ATLAS) facility provides low-energy and accelerated neutron-rich radioactive beams to address key nuclear physics and astrophysics questions. A 350 mCi 252Cf source produces fission fragments which are thermalized and collected by a helium gas catcher into a low-energy particle beam with a charge of 1+ or 2+. An electron cyclotron resonance (ECR) ion source functions as a charge breeder in order to raise the ion charge sufficiently for acceleration in the ATLAS linac. The ECR charge breeder has achieved stable beam charge breeding efficiencies of 10.1% for 23Na7+, 17.9% for 39K10+, 15.6% for 84Kr17+, and 12.4% for 133Cs27+. For the radioactive beams, a charge breeding efficiency of 11.7% has been achieved for 143Cs27+ and 14.7% for 143Ba27+. The typical breeding times are 10 ms/charge state, but the source can be tuned such that this value increases to 100 ms/charge state with the best breeding efficiency corresponding to the longest breeding times—the variation of efficiencies with breeding time will be discussed. Efforts have been made to characterize and reduce the background contaminants present in the ion beam through judicious choice of q/m combinations. Methods of background reduction are being investigated based upon plasma chamber cleaning and vacuum practices.

  9. Palladium-catalyzed oxidative diffusion for tritium extraction from breeder-blanket fluids at low concentrations

    NASA Astrophysics Data System (ADS)

    Hsu, Cheazone; Buxbaum, Robert E.

    1986-11-01

    Oxidative diffusion can extract hydrogen from metal solutions at extremely low partial pressures. The hydrogen diffuses through a metal membrane and is oxidized to water. The oxidation reaction produces the very low downstream pressures that drive the flux. This method is attractive because the flux can be proportional to the square-root of upstream pressure. For fusion reactors with liquid lithium or lithium-lead alloy breeder blankets, permeation windows provide a simple, cheap tritium extraction method. Interdiffusion rates, separation flux, window size, helium contents, tritium holdup costs, and overall costs are calculated for membranes of palladium-coated zirconium, niobium, vanadium, nickel and stainless-steel. For extracting tritium from liquid lithium using the cheapest windows, Zr-Pd, the material and labor cost is 8.0 M at 1 wppm, and is inversely proportional to tritium concentration in the lithium. The tritium holdup cost for the windows is 4.8 M, and for the blanket it is proportional to the blanket volume and concentration. An overall economic optimization suggests that 1 to 1.5 wppm in lithium is optimal. For extracting tritium from 17Li83Pb at 0.26 wppb, the cheapest window is V-Pd; the cost is 2.6 M$, and the tritium holdup is negligible.

  10. Campylobacter epidemiology from breeders to their progeny in Eastern Spain.

    PubMed

    Ingresa-Capaccioni, S; Jiménez-Trigos, E; Marco-Jiménez, F; Catalá, P; Vega, S; Marin, C

    2016-03-01

    While horizontal transmission is a route clearly linked to the spread of Campylobacter at the farm level, few studies support the transmission of Campylobacter spp. from breeder flocks to their offspring. Thus, the present study was carried out to investigate the possibility of vertical transmission. Breeders were monitored from the time of housing day-old chicks, then throughout the laying period (0 to 60 wk) and throughout their progeny (broiler fattening, 1 to 42 d) until slaughter. All samples were analyzed according with official method ISO 10272:2006. Results revealed that on breeder farms, Campylobacter isolation started from wk 16 and reached its peak at wk 26, with 57.0% and 93.2% of positive birds, respectively. After this point, the rate of positive birds decreased slightly to 86.0% at 60 wk. However, in broiler production all day-old chicks were found negative for Campylobacter spp, and the bacteria was first isolated at d 14 of age (5.0%), with a significant increase in detection during the fattening period with 62% of Campylobacter positive animals at the end of the production cycle. Moreover, non-positive sample was determined from environmental sources. These results could be explained because Campylobacter may be in a low concentration or in a non-culturable form, as there were several studies that successfully detected Campylobacter DNA, but failed to culture. This form can survive in the environment and infect successive flocks; consequently, further studies are needed to develop more modern, practical, cost-effective and suitable techniques for routine diagnosis. PMID:26628341

  11. Steam generator tubing development for commercial fast breeder reactors

    SciTech Connect

    Sessions, C.E.; Uber, C.F.

    1981-11-01

    The development work to design, manufacture, and evaluate pre-stressed double-wall 2/one quarter/ Cr-1 Mo steel tubing for commercial fast breeder reactor steam generator application is discussed. The Westinghouse plan for qualifying tubing vendors to produce this tubing is described. The results achieved to date show that a long length pre-stressed double-wall tube is both feasible and commercially available. The evaluation included structural analysis and experimental measurement of the pre-stress within tubes, as well as dimensional, metallurgical, and interface wear tests of tube samples produced. This work is summarized and found to meet the steam generator design requirements. 10 refs.

  12. Secure automated fabrication: remote fabrication of breeder-reactor fuel

    SciTech Connect

    Gerber, E.W.; Rice, L.H.; Horgos, R.M.; Nagamoto, T.T.; Graham, R.A.

    1981-05-01

    The Secure Automated Fabrication (SAF) Program was initiated at the Hanford Engineering Development Laboratory (HEDL) to develop and demonstrate an advanced manufacturing line (SAF line) for plutonium oxide breeder reactor fuel pins. The SAF line is to be installed in the Fuels and Materials Examination Facility (FMEF) at Hanford and will utilize technology that focuses on improved safety features for plant operating personnel, the public, and the environment. Equipment and process improvements incorporated by the SAF line will yield significant gains in nuclear materials safeguards, product quality and productivity.

  13. Innovative Universities.

    ERIC Educational Resources Information Center

    Barsi, Louis M.; Kaebnick, Gweneth W.

    1989-01-01

    The phenomenon of innovation within the university is examined, noting the possibility of innovation as a key to college vitality. A study was conducted using a group of institutions that demonstrated recent innovative spirit. Members of the American Association of State Colleges and Universities (AASCU), each has been recognized in an annual…

  14. Group size adjustment to ecological demand in a cooperative breeder

    PubMed Central

    Zöttl, Markus; Frommen, Joachim G.; Taborsky, Michael

    2013-01-01

    Environmental factors can determine which group size will maximize the fitness of group members. This is particularly important in cooperative breeders, where group members often serve different purposes. Experimental studies are yet lacking to check whether ecologically mediated need for help will change the propensity of dominant group members to accept immigrants. Here, we manipulated the perceived risk of predation for dominant breeders of the cooperatively breeding cichlid fish Neolamprologus pulcher to test their response to unrelated and previously unknown immigrants. Potential immigrants were more readily accepted if groups were exposed to fish predators or egg predators than to herbivorous fish or control situations lacking predation risk. Our data are consistent with both risk dilution and helping effects. Egg predators were presented before spawning, which might suggest that the fish adjust acceptance rates also to a potential future threat. Dominant group members of N. pulcher apparently consider both present and future need of help based on ecological demand. This suggests that acceptance of immigrants and, more generally, tolerance of group members on demand could be a widespread response to ecological conditions in cooperatively breeding animals. PMID:23390105

  15. Ceramic breeder research and development: progress and focus

    NASA Astrophysics Data System (ADS)

    van der Laan, J. G.; Kawamura, H.; Roux, N.; Yamaki, D.

    2000-12-01

    The world-wide efforts on ceramic breeder materials in the last two years concerned Li2O, Li4SiO4, Li2TiO3 and Li2ZrO3, with a clear emphasis on the development of Li2TiO3. Pebble-manufacturing processes have been developed up to a 10 kg scale. Characterisation of materials has advanced. A jump-wise progress is observed in the characterisation of pebble-beds, in particular of their thermo-mechanical behaviour. Thermal property data are still limited. A number of breeder materials have been or are being irradiated in material test reactors like HFR and JMTR. The EXOTIC-8 series of in-pile experiments is a major source of tritium release data. This paper discusses the technical advancements and proposes a focus for further research and development (R&D) : pebble-bed mechanical and thermal behaviour and its interactions with the blanket structure as a function of temperature, burn-up, irradiation dose and time; tritium release and retention properties; determination of the key factors limiting blanket life.

  16. Design of a helium-cooled molten salt fusion breeder

    SciTech Connect

    Moir, R.W.; Lee, J.D.; Fulton, F.J.; Huegel, F.; Neef, W.S. Jr.; Sherwood, A.E.; Berwald, D.H.; Whitley, R.H.; Wong, C.P.C.; DeVan, J.H.

    1985-02-01

    A new conceptual blanket design for a fusion reactor produces fissile material for fission power plants. Fission is suppressed by using beryllium, rather than uranium, to multiply neutrons and also by minimizing the fissile inventory. The molten-salt breeding media (LiF + BeF/sub 2/ + TghF/sub 4/) is circulated through the blanket and on to the online processing system where /sup 233/U and tritium are continuously removed. Helium cools the blanket including the steel pipes containing the molten salt. Austenitic steel was chosen because of its ease of fabrication, adequate radiation-damage lifetime, and low corrosion rate by molten salt. We estimate the breeder, having 3000 MW of fusion power, produces 6400 kg of /sup 233/U per year, which is enough to provide make up for 20 GWe of LWR per year (or 14 LWR plants of 4440 MWt) or twice that many HTGRs or CANDUs. Safety is enhanced because the afterheat is low and the blanket materials do not react with air or water. The fusion breeder based on a pre-MARS tandem mirror is estimated to cost $4.9B or 2.35 times an LWR of the same power. The estimated present value cost of the /sup 2/anumber/sup 3/U produced is $40/g if utility financed or $16/g if government financed.

  17. Experimental reproduction of enterococcal spondylitis in male broiler breeder chickens.

    PubMed

    Martin, Leslie T; Martin, Michael P; Barnes, H John

    2011-06-01

    There has been a recent emergence of epidemic spinal infections with necrosis causing lameness and mortality in male broilers and broiler breeders. Mortality in affected flocks may be as high as 15%. The disease has been called enterococcal spondylitis (ES), based on the frequent isolation of Enterococcus cecorum from the lesions and necrosis and inflammation observed in the free thoracic vertebrae (FTV) of affected birds. Male broiler breeders in an experimental setting were challenged with pure E. cecorum isolates obtained from ES-affected commercial flocks. Challenge routes included oral gavage (10(8)), intravenous (i.v.; 10(3)), and air sac (AS; 10(3)). Half the study birds in each group were chemically immunosuppressed with dexamethasone. Spinal lesions were observed grossly in birds challenged intravenously (2.9%) and birds challenged orally (6.1%). Microscopic spinal lesions consistent with ES were more frequently identified compared with gross lesions in the orally challenged group (30.3%). Chemical immunosuppression with dexamethasone was not associated with a greater incidence of ES in this study. By recreating the disease experimentally, the study design reported here may help in the further development of an experimental challenge model for future studies on risk factors, prevention, and therapeutic intervention of ES. PMID:21793445

  18. Mechanical design of a light water breeder reactor

    DOEpatents

    Fauth, Jr., William L.; Jones, Daniel S.; Kolsun, George J.; Erbes, John G.; Brennan, John J.; Weissburg, James A.; Sharbaugh, John E.

    1976-01-01

    In a light water reactor system using the thorium-232 -- uranium-233 fuel system in a seed-blanket modular core configuration having the modules arranged in a symmetrical array surrounded by a reflector blanket region, the seed regions are disposed for a longitudinal movement between the fixed or stationary blanket region which surrounds each seed region. Control of the reactor is obtained by moving the inner seed region thus changing the geometry of the reactor, and thereby changing the leakage of neutrons from the relatively small seed region into the blanket region. The mechanical design of the Light Water Breeder Reactor (LWBR) core includes means for axially positioning of movable fuel assemblies to achieve the neutron economy required of a breeder reactor, a structure necessary to adequately support the fuel modules without imposing penalties on the breeding capability, a structure necessary to support fuel rods in a closely packed array and a structure necessary to direct and control the flow of coolant to regions in the core in accordance with the heat transfer requirements.

  19. Educating the Next Generation of Plant Breeders: The Need and the Challenge

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Plant breeding is critical to the future of productive agriculture, food security, and economic prosperity. Increasingly, many plant breeders are working in industry or governmental agencies that do not include education of the next generation of plant breeders as part of their mission. At the sam...

  20. Impacts of breeder loss on social structure, reproduction and population growth in a social canid.

    PubMed

    Borg, Bridget L; Brainerd, Scott M; Meier, Thomas J; Prugh, Laura R

    2015-01-01

    The importance of individuals to the dynamics of populations may depend on reproductive status, especially for species with complex social structure. Loss of reproductive individuals in socially complex species could disproportionately affect population dynamics by destabilizing social structure and reducing population growth. Alternatively, compensatory mechanisms such as rapid replacement of breeders may result in little disruption. The impact of breeder loss on the population dynamics of social species remains poorly understood. We evaluated the effect of breeder loss on social stability, recruitment and population growth of grey wolves (Canis lupus) in Denali National Park and Preserve, Alaska using a 26-year dataset of 387 radiocollared wolves. Harvest of breeding wolves is a highly contentious conservation and management issue worldwide, with unknown population-level consequences. Breeder loss preceded 77% of cases (n = 53) of pack dissolution from 1986 to 2012. Packs were more likely to dissolve if a female or both breeders were lost and pack size was small. Harvest of breeders increased the probability of pack dissolution, likely because the timing of harvest coincided with the breeding season of wolves. Rates of denning and successful recruitment were uniformly high for packs that did not experience breeder loss; however, packs that lost breeders exhibited lower denning and recruitment rates. Breeder mortality and pack dissolution had no significant effects on immediate or longer term population dynamics. Our results indicate the importance of breeding individuals is context dependent. The impact of breeder loss on social group persistence, reproduction and population growth may be greatest when average group sizes are small and mortality occurs during the breeding season. This study highlights the importance of reproductive individuals in maintaining group cohesion in social species, but at the population level socially complex species may be resilient

  1. Light-water breeder reactor (LWBR Development Program)

    DOEpatents

    Beaudoin, B.R.; Cohen, J.D.; Jones, D.H.; Marier, L.J. Jr.; Raab, H.F.

    1972-06-20

    Described is a light-water-moderated and -cooled nuclear breeder reactor of the seed-blanket type characterized by core modules comprising loosely packed blanket zones enriched with fissile fuel and axial zoning in the seed and blanket regions within each core module. Reactivity control over lifetime is achieved by axial displacement of movable seed zones without the use of poison rods in the embodiment illustrated. The seed is further characterized by a hydrogen-to-uranium-233 atom ratio in the range 10 to 200 and a uranium-233-to-thorium-232 atom ratio ranging from 0.012 to 0.200. The seed occupies from 10 to 35 percent of the core volume in the form of one or more individual islands or annuli. (NSA 26: 55130)

  2. Designing a SCADA system simulator for fast breeder reactor

    NASA Astrophysics Data System (ADS)

    Nugraha, E.; Abdullah, A. G.; Hakim, D. L.

    2016-04-01

    SCADA (Supervisory Control and Data Acquisition) system simulator is a Human Machine Interface-based software that is able to visualize the process of a plant. This study describes the results of the process of designing a SCADA system simulator that aims to facilitate the operator in monitoring, controlling, handling the alarm, accessing historical data and historical trend in Nuclear Power Plant (NPP) type Fast Breeder Reactor (FBR). This research used simulation to simulate NPP type FBR Kalpakkam in India. This simulator was developed using Wonderware Intouch software 10 and is equipped with main menu, plant overview, area graphics, control display, set point display, alarm system, real-time trending, historical trending and security system. This simulator can properly simulate the principle of energy flow and energy conversion process on NPP type FBR. This SCADA system simulator can be used as training media for NPP type FBR prospective operators.

  3. UF6 breeder reactor power plants for electric power generation

    NASA Technical Reports Server (NTRS)

    Rust, J. H.; Clement, J. D.; Hohl, F.

    1976-01-01

    The reactor concept analyzed is a U-233F6 core surrounded by a molten salt (Li(7)F, BeF2, ThF4) blanket. Nuclear survey calculations were carried out for both spherical and cylindrical geometries. Thermodynamic cycle calculations were performed for a variety of Rankine cycles. A conceptual design is presented along with a system layout for a 1000 MW stationary power plant. Advantages of the gas core breeder reactor (GCBR) are as follows: (1) high efficiency; (2) simplified on-line reprocessing; (3) inherent safety considerations; (4) high breeding ratio; (5) possibility of burning all or most of the long-lived nuclear waste actinides; and (6) possibility of extrapolating the technology to higher temperatures and MHD direct conversion.

  4. Differential gene expression in cumulus oocyte complexes collected by ovum pick up from repeat breeder and normally fertile Holstein Friesian heifers.

    PubMed

    Puglisi, Roberto; Cambuli, Caterina; Capoferri, Rossana; Giannino, Laura; Lukaj, Aleksander; Duchi, Roberto; Lazzari, Giovanna; Galli, Cesare; Feligini, Maria; Galli, Andrea; Bongioni, Graziella

    2013-09-01

    The aim of this study was to establish whether perturbed gene expression during cumulus oocyte development causes repeat breeding in cattle. In this study, a repeat breeder was defined as a normal estrous cycling animal that did not become pregnant after three inseminations despite the absence of clinically detectable reproductive disorders. Transcripts of genes extracted from cumulus oocyte complexes (COC) that were collected from three repeat breeder and three normally fertile Holstein Friesian heifers were compared. Up to 40 COC were collected from each heifer by means of repeated sessions of ovum pick up in the absence of hormonal stimulation; immediately plunged into liquid nitrogen; and stored at -80°C until analysis. For each heifer, RNA was extracted from the pooled COC and hybridized on GeneChip(®) Bovine Gene Array (Affymetrix). Analysis of gene expression profiles of repeat breeder and control COC showed that 178 genes were differentially expressed (log2 fold change>1.5). Of these genes, 43 (24%) were up-regulated and 135 (76%) were down-regulated in repeat breeder relative to control heifers. This altered pattern of expression occurred in genes involved in several cellular biological processes and cellular components such as metabolism, angiogenesis, substrate/ion transport, regulation/signaling, cell adhesion and cytoskeleton. From these, 13 genes potentially involved in cumulus oocyte growth were subjected to validation by qRT-PCR and nine genes (annexin A1, ANXA1; lactoferrin, LTF; interferon stimulated exonuclease 20kDa, ISG20/HEM45; oxidized low density lipoprotein receptor 1, OLR1; fatty acid desaturase 2, FADS2; glutathione S-transferase A2 and A4, GSTA2 and GSTA4; glutathione peroxidase 1, GPX1; endothelin receptor type A, EDNRA) were confirmed to be differentially expressed. This study identified potential marker genes for fertility in dairy cattle. PMID:23911014

  5. Innovation @ NASA

    NASA Technical Reports Server (NTRS)

    Roman, Juan A.

    2014-01-01

    This presentation provides an overview of the activities National Aeronautics and Space Administration (NASA) is doing to encourage innovation across the agency. All information provided is available publicly.

  6. Fuel Summary Report: Shippingport Light Water Breeder Reactor

    SciTech Connect

    Illum, D.B.; Olson, G.L.; McCardell, R.K.

    1999-01-01

    The Shippingport Light Water Breeder Reactor (LWBR) was a small water cooled, U-233/Th-232 cycle breeder reactor developed by the Pittsburgh Naval Reactors to improve utilization of the nation's nuclear fuel resources in light water reactors. The LWBR was operated at Shippingport Atomic Power Station (APS), which was a Department of Energy (DOE) (formerly Atomic Energy Commission)-owned reactor plant. Shippingport APS was the first large-scale, central-station nuclear power plant in the United States and the first plant of such size in the world operated solely to produce electric power. The Shippingport LWBR was operated successfully from 1977 to 1982 at the APS. During the five years of operation, the LWBR generated more than 29,000 effective full power hours (EFPH) of energy. After final shutdown, the 39 core modules of the LWBR were shipped to the Expended Core Facility (ECF) at Naval Reactors Facility at the Idaho National Engineering and Environmental Laboratory (INEEL). At ECF, 12 of the 39 modules were dismantled and about 1000 of more than 17,000 rods were removed from the modules of proof-of-breeding and fuel performance testing. Some of the removed rods were kept at ECF, some were sent to Argonne National Laboratory-West (ANL-W) in Idaho and some to ANL-East in Chicago for a variety of physical, chemical and radiological examinations. All rods and rod sections remaining after the experiments were shipped back to ECF, where modules and loose rods were repackaged in liners for dry storage. In a series of shipments, the liners were transported from ECF to Idaho Nuclear Technology Engineering Center (INTEC), formerly the Idaho Chemical Processing Plant (ICPP). The 47 liners containing the fully-rodded and partially-derodded core modules, the loose rods, and the rod scraps, are now stored in underground dry wells at CPP-749.

  7. Helium-cooled molten-salt fusion breeder

    SciTech Connect

    Moir, R.W.; Lee, J.D.; Fulton, F.J.; Huegel, F.; Neef, W.S. Jr.; Sherwood, A.E.; Berwald, D.H.; Whitley, R.H.; Wong, C.P.C.; Devan, J.H.

    1984-12-01

    We present a new conceptual design for a fusion reactor blanket that is intended to produce fissile material for fission power plants. Fast fission is suppressed by using beryllium instead of uranium to multiply neutrons. Thermal fission is suppressed by minimizing the fissile inventory. The molten-salt breeding medium (LiF + BeF/sub 2/ + ThF/sub 4/) is circulated through the blanket and to the on-line processing system where /sup 233/U and tritium are continuously removed. Helium cools the blanket and the austenitic steel tubes that contain the molten salt. Austenitic steel was chosen because of its ease of fabrication, adequate radiation-damage lifetime, and low corrosion by molten salt. We estimate that a breeder having 3000 MW of fusion power will produce 6500 kg of /sup 233/U per year. This amount is enough to provide makeup for 20 GWe of light-water reactors per year or twice that many high-temperature gas-cooled reactors or Canadian heavy-water reactors. Safety is enhanced because the afterheat is low and blanket materials do not react with air or water. The fusion breeder based on a pre-MARS tandem mirror is estimated to cost $4.9B or 2.35 times a light-water reactor of the same power. The estimated cost of the /sup 233/U produced is $40/g for fusion plants costing 2.35 times that of a light-water reactor if utility owned or $16/g if government owned.

  8. Litter loss triggers estrus in a nonsocial seasonal breeder

    PubMed Central

    Steyaert, Sam MJG; Swenson, Jon E; Zedrosser, Andreas

    2014-01-01

    Sexually selected infanticide (SSI) is often presumed to be rare among seasonal breeders, because it would require a near immediate return to estrus after the loss of an entire litter during the mating season. We evaluated changes in reproductive strategies and the reproductive fate of females that experienced litter loss during the mating season in a seasonal breeder with strong evidence for SSI, the brown bear. First, we used a long-term demographic dataset (1986–2011) to document that a large majority of females (>91%) that lose their entire litter during the mating season in fact do enter estrus, mate, and give birth during the subsequent birthing season. Second, we used high-resolution movement data (2005–2011) to evaluate how females changed reproductive strategies after losing their entire litter during the mating season. We hypothesized that females would shift from the sedentary lifestyle typical for females with cubs-of-the-year to a roam-to-mate behavior typical for receptive females in no more than a few (∼3) days after litter loss. We found that females with cubs-of-the-year moved at about 1/3 of the rate and in a less bimodal diurnal pattern than receptive females during the mating season. The probability of litter loss was positively related with movement rate, suggesting that being elusive and sedentary is a strategy to enhance cub survival rather than a relic of cub mobility itself. The movement patterns of receptive females and females after litter loss were indistinguishable within 1–2 days after the litter loss, and we illustrate that SSI can significantly reduce the female interbirth interval (50–85%). Our results suggest that SSI can also be advantageous for males in seasonally breeding mammals. We propose that infanticide as a male reproductive strategy is more prevalent among mammals with reproductive seasonality than observed or reported. PMID:24558586

  9. Atmospheric Dispersion of Sodium Aerosol due to a Sodium Leak in a Fast Breeder Reactor Complex

    NASA Astrophysics Data System (ADS)

    Punitha, G.; Sudha, A. Jasmin; Kasinathan, N.; Rajan, M.

    Liquid sodium at high temperatures (470 K to 825 K) is used as the primary and secondary coolant in Liquid Metal cooled Fast Breeder Reactors (LMFBR). In the event of a postulated sodium leak in the Steam Generator Building (SGB) of a LMFBR, sodium readily combusts in the ambient air, especially at temperatures above 523 K. Intense sodium fire results and sodium oxide fumes are released as sodium aerosols. Sodium oxides are readily converted to sodium hydroxide in air due to the presence of moisture in it. Hence, sodium aerosols are invariably in the form of particulate sodium hydroxide. These aerosols damage not only the equipment and instruments due to their corrosive nature but also pose health hazard to humans. Hence, it is essential to estimate the concentration of sodium aerosols within the plant boundary for a sodium leak event. The Gaussian Plume Dispersion Model can obtain the atmospheric dispersion of sodium aerosols in an open terrain. However, this model does not give accurate results for dispersion in spaces close to the point of release and with buildings in between. The velocity field due to the wind is altered to a large extent by the intervening buildings and structures. Therefore, a detailed 3-D estimation of the velocity field and concentration has to be obtained through rigorous computational fluid dynamics (CFD) approach. PHOENICS code has been employed to determine concentration of sodium aerosols at various distances from the point of release. The dispersion studies have been carried out for the release of sodium aerosols at different elevations from the ground and for different wind directions.

  10. An innovative arrangement for in-vial membrane-assisted liquid-liquid microextraction: application to the determination of esters of phthalic acid in alcoholic beverages by gas chromatography-mass spectrometry.

    PubMed

    March, Juan Gabriel; Cerdà, Victor

    2015-05-01

    A new arrangement for membrane-assisted liquid-liquid microextraction is presented. The extracting organic solvent was placed into a chromatographic microvial, compatible with the chromatograph autosampler, whose septum was replaced by a disc of porous hydrophobic membrane. This extraction device was completely immersed into the analytical sample contained in a cylindrical container subjected to rotary and basculant movement. Then, the extraction of analytes took place from the sample to the organic solvent contained in the vial through the membrane. Esters of the phthalic acid have been selected as model analytes to determine the performance characteristics of the extraction system. The limits of detection, limits of quantification and relative standard deviations (%) were in the range 0.1-0.4, 0.3-1 and 4-7, respectively. Esters of phthalic acid have been successfully analysed in alcoholic beverages. The main operational advantages of this arrangement consisted of minimal required handling, minimal risk of cross contamination and its simplicity. PMID:25876533

  11. Results with the electron cyclotron resonance charge breeder for the {sup 252}Cf fission source project (Californium Rare Ion Breeder Upgrade) at Argonne Tandem Linac Accelerator System

    SciTech Connect

    Vondrasek, R.; Kondrashev, S.; Pardo, R.; Scott, R.; Zinkann, G. P.

    2010-02-15

    The construction of the Californium Rare Ion Breeder Upgrade, a new radioactive beam facility for the Argonne Tandem Linac Accelerator System (ATLAS), is nearing completion. The facility will use fission fragments from a 1 Ci {sup 252}Cf source; thermalized and collected into a low-energy particle beam by a helium gas catcher. In order to reaccelerate these beams, an existing ATLAS electron cyclotron resonance (ECR) ion source was redesigned to function as an ECR charge breeder. Thus far, the charge breeder has been tested with stable beams of rubidium and cesium achieving charge breeding efficiencies of 9.7% into {sup 85}Rb{sup 17+} and 2.9% into {sup 133}Cs{sup 20+}.

  12. Nucleon-meson transport capability for accelerator-breeder target design. [CALOR

    SciTech Connect

    Gabriel, T.A.; Alsmiller, R.G. Jr.

    1982-01-01

    A state-of-the-art code system for nucleon-meson-lepton transport which has direct applicability to accelerator breeders is presented. Some pertinent data that have been obtained using this system are discussed and compared with experimental data.

  13. The Case Against the Fast Breeder Reactor: An Anti-Nuclear Establishment View.

    ERIC Educational Resources Information Center

    Lovins, Amory B.

    1973-01-01

    Environmentalists lobby points out that hazards which may result from mistakes in proposed fast breeder reactor for additional energy can be detrimental for mankind. Such projects must be carefully planned and cautiously executed. (PS)

  14. Innovative Partnerships

    USGS Publications Warehouse

    Szemraj, John

    2001-01-01

    A major responsibility of the U.S. Geological Survey (USGS) is to ensure geospatial data availability. This includes the cooperative production of digital geospatial data through the National Mapping Program's Innovative Partnerships (IP) initiative, which began in October 1992.

  15. The prevalence of subclinical endometritis and intrauterine infections in repeat breeder cows.

    PubMed

    Pothmann, H; Prunner, I; Wagener, K; Jaureguiberry, M; de la Sota, R L; Erber, R; Aurich, C; Ehling-Schulz, M; Drillich, M

    2015-05-01

    The objectives of this study were to assess the prevalence of subclinical endometritis and the presence of common uterine pathogens in repeat breeder cows. A total of 121 cows with three or more consecutive artificial inseminations without conception and no clinical signs of disease were defined as repeat breeder cows and were enrolled in this trial. Intrauterine samples were collected with the cytobrush technique to determine the prevalence of subclinical endometritis and bacteriologic infections. Blood samples were analyzed for concentrations of progesterone and estradiol in plasma to assess ovarian activity. Furthermore, breed, parity, history of calving and postpartum uterine infection, clinical findings of transrectal palpation, and backfat thickness were analyzed as potential factors for the prevalence of subclinical endometritis in repeat breeder cows. The prevalence of subclinical endometritis in repeat breeder cows was 12.7%; but common uterine pathogens, Escherichia coli and Trueperella pyogenes, were found in only one and three cows, respectively. Ovarian activity was determined in 95.0% of all cows. Recorded variables had no effect on the prevalence of subclinical endometritis in repeat breeder cows. In conclusion, subclinical endometritis and uterine infections linked to common pathogens were playing a minor role as a cause for repeat breeder cows in this study. Alternative reasons for failure to conceive in these cows are discussed. PMID:25670153

  16. Feasibility study of a fission-suppressed tokamak fusion breeder

    SciTech Connect

    Moir, R.W.; Lee, J.D.; Neef, W.S.; Berwald, D.H.; Garner, J.K.; Whitley, R.H.; Ghoniem, N.; Wong, C.P.C.; Maya, I.; Schultz, K.R.

    1984-12-01

    The preliminary conceptual design of a tokamak fissile fuel producer is described. The blanket technology is based on the fission suppressed breeding concept where neutron multiplication occurs in a bed of 2 cm diameter beryllium pebbles which are cooled by helium at 50 atmospheres pressure. Uranium-233 is bred in thorium metal fuel elements which are in the form of snap rings attached to each beryllium pebble. Tritium is bred in lithium bearing material contained in tubes immersed in the pebble bed and is recovered by a purge flow of helium. The neutron wall load is 3 MW/m/sup 2/ and the blanket material is ferritic steel. The net fissile breeding ratio is 0.54 +- 30% per fusion reaction. This results in the production of 4900 kg of /sup 233/U per year from 3000 MW of fusion power. This quantity of fuel will provide makeup fuel for about 12 LWRs of equal thermal power or about 18 1 GW/sub e/ LWRs. The calculated cost of the produced uranium-233 is between $23/g and $53/g or equivalent to $10/kg to $90/kg of U/sub 3/O/sub 8/ depending on government financing or utility financing assumptions. Additional topics discussed in the report include the tokamak operating mode (both steady state and long pulse considered), the design and breeding implications of using a poloidal divertor for impurity control, reactor safety, the choice of a tritium breeder, and fuel management.

  17. Ultrasonic decontamination of prototype fast breeder reactor fuel pins.

    PubMed

    Kumar, Aniruddha; Bhatt, R B; Behere, P G; Afzal, Mohd

    2014-04-01

    Fuel pin decontamination is the process of removing particulates of radioactive material from its exterior surface. It is an important process step in nuclear fuel fabrication. It assumes more significance with plutonium bearing fuel known to be highly radio-toxic owing to its relatively longer biological half life and shorter radiological half life. Release of even minute quantity of plutonium oxide powder in the atmosphere during its handling can cause alarming air borne activity and may pose a severe health hazard to personnel working in the vicinity. Decontamination of fuel pins post pellet loading operation is thus mandatory before they are removed from the glove box for further processing and assembly. This paper describes the setting up of ultrasonic decontamination process, installed inside a custom built fume-hood in the production line, comprising of a cleaning tank with transducers, heaters, pin handling device and water filtration system and its application in cleaning of fuel pins for prototype fast breeder reactor. The cleaning process yielded a typical decontamination efficiency of more than 99%. PMID:24405906

  18. Coupling of OECD standardized test and immunomarkers to select the most environmentally benign ionic liquids option--towards an innovative "safety by design" approach.

    PubMed

    Bado-Nilles, Anne; Diallo, Alpha-Oumar; Marlair, Guy; Pandard, Pascal; Chabot, Laure; Geffard, Alain; Len, Christophe; Porcher, Jean-Marc; Sanchez, Wilfried

    2015-01-01

    This paper proposed a potential industrial accompaniment to reduce ionic liquid harmfulness by a novel combination of OECD Daphnia magna standardized test and fish immunomarkers. The combination of these two tests allowed multicriteria examination of ILs impacts in different organisms and trophic levels. The work provided new data for legislation and opened a door towards an integrative environmental evaluation due to direct implications of immune system in fish and ecosystem health. Whatever the species, each IL tested induced deleterious effects suggesting that toxic impact was especially due to IL lipophilicity properties. Nevertheless, cation moieties of ILs seemed to draw overall toxicity of ILs to significant extent as supported by lower cell mortality shown with imidazolium-based ILs compared to phosphonium-based ILs. However, the anions moieties have some additional effect, as revealed by quite dissimilar toxicity within same IL family. Concerning the more integrative biomarkers, the cationic-based ILs tested possessed also dissimilar effect on immune system of fish, especially on leucocyte distribution, lysosomal membrane integrity and phagocytosis activity. These results confirm that ILs toxicity could be influenced by design and that chemical engineering processes can integrate ecological footprint reduction strategies for successful IL utilization in the future. PMID:25278158

  19. Tubular gage for a liquid-metal-cooled fast breeder reactor

    DOEpatents

    Hutter, Ernest; Tuma, Leroy A.

    1977-06-14

    Spring-loaded plungers are arranged about a housing for insertion into a polygonal tube, one plunger for each side of the tube. Each plunger has a locking cam and sliding wedge mechanism which can overcome the spring force associated with the plunger and lock it in any position. The wedges are operated by a rod moveable axially in the housing. Several housings with their associated plungers can be stacked. The stack is lowered into the polygonal tube with all of the plungers locked in a fully inward position. When the stack is in the tube, each wedge is moved to release its locking cam, allowing each of the plungers to spring outward against an inner side of the tube. Each housing will thus gage the internal dimensions of the tube at its elevation. The plungers are locked in position, the entire stack is rotated to bring the plungers into the corners described by the intersections of the flat sides, and the stack is removed from the tube whereupon the dimensions across opposite locked plungers may be read by a micrometer.

  20. Mechanical properties test data of Alloy 718 for liquid metal fast breeder reactor applications

    SciTech Connect

    Korth, G.E.

    1983-01-01

    Mechanical property test data are reported for Alloy 718 with two heat treatments: conventional heat treatment (CHT) for base metal and Idaho National Engineering Laboratory (INEL) heat treatment (IHT) for base and weld metal. Tests were conducted in air from 24 to 704{degree}C and include elastic properties (Young's modulus, shear modulus, Poisson's ratio), tensile properties, creep-rupture properties, fatigue properties, creep-fatigue properties, and Charpy impact behavior. Effects of long term thermal aging at 538, 593, 649, and 704{degree}C for times to 25,000 h are also reported for CHT material (tensile, creep-rupture, fatigue, and Charpy), and IHT material (tensile, and Charpy). 18 refs., 63 figs., 36 tabs.

  1. Thermal-performance study of liquid metal fast breeder reactor insulation

    SciTech Connect

    Shiu, Kelvin K.

    1980-09-01

    Three types of metallic thermal insulation were investigated analytically and experimentally: multilayer reflective plates, multilayer honeycomb composite, and multilayer screens. Each type was subjected to evacuated and nonevacuated conditions, where thermal measurements were made to determine thermal-physical characteristics. A variation of the separation distance between adjacent reflective plates of multilayer reflective plates and multilayer screen insulation was also experimentally studied to reveal its significance. One configuration of the multilayer screen insulation was further selected to be examined in sodium and sodium oxide environments. The emissivity of Type 304 stainless steel used in comprising the insulation was measured by employing infrared technology. A comprehensive model was developed to describe the different proposed types of thermal insulation. Various modes of heat transfer inherent in each type of insulation were addressed and their relative importance compared. Provision was also made in the model to allow accurate simulation of possible sodium and sodium oxide contamination of the insulation. The thermal-radiation contribution to heat transfer in the temperature range of interest for LMFBR's was found to be moderate, and the suppression of natural convection within the insulation was vital in preserving its insulating properties. Experimental data were compared with the model and other published results. Moreover, the three proposed test samples were assessed and compared under various conditions as viable LMFBR thermal insulations.

  2. Piping support system for liquid-metal fast-breeder reactor

    DOEpatents

    Brussalis, Jr., William G.

    1984-01-01

    A pipe support consisting of a rigid link pivotally attached to a pipe and an anchor, adapted to generate stress or strain in the link and pipe due to pipe thermal movement, which stress or strain can oppose further pipe movement and generally provides pipe support. The pipe support can be used in multiple combinations with other pipe supports to form a support system. This support system is most useful in applications in which the pipe is normally operated at a constant elevated or depressed temperature such that desired stress or strain can be planned in advance of pipe and support installation. The support system is therefore especially useful in steam stations and in refrigeration equipment.

  3. US Liquid Metal Fast Breeder Reactor man-machine interface program

    SciTech Connect

    Vaurio, J.K.; Change, S.A.

    1982-01-01

    The US LMFBR Man-Machine Interface Program is supportive to and an integral part of the LMFBR Safety Program. This paper describes the goal and objectives of the program, and the necessary research and development efforts with a logical structure for the orderly and timely implementation of the prgoram. Current status and near-term and long-term priority activities are also summarized.

  4. Decommissioning of Experimental Breeder Reactor - II Complex, Post Sodium Draining

    SciTech Connect

    J. A. Michelbacher; S. Paul Henslee; Collin J. Knight; Steven R. sherman

    2005-09-01

    The Experimental Breeder Reactor - II (EBR-II) was shutdown in September 1994 as mandated by the United States Department of Energy. This sodium-cooled reactor had been in service since 1964. The bulk sodium was drained from the primary and secondary systems and processed. Residual sodium remaining in the systems after draining was converted into sodium bicarbonate using humid carbon dioxide. This technique was tested at Argonne National Laboratory in Illinois under controlled conditions, then demonstrated on a larger scale by treating residual sodium within the EBR-II secondary cooling system, followed by the primary tank. This process, terminated in 2002, was used to place a layer of sodium bicarbonate over all exposed surfaces of sodium. Treatment of the remaining EBR-II sodium is governed by the Resource Conservation and Recovery Act (RCRA). The Idaho Department of Environmental Quality issued a RCRA Operating Permit in 2002, mandating that all hazardous materials be removed from EBR-II within a 10 year period, with the ability to extend the permit and treatment period for another 10 years. A preliminary plan has been formulated to remove the remaining sodium and NaK from the primary and secondary systems using moist carbon dioxide, steam and nitrogen, and a water flush. The moist carbon dioxide treatment was resumed in May 2004. As of August 2005, approximately 60% of the residual sodium within the EBR-II primary tank had been treated. This process will continue through the end of 2005, when it is forecast that the process will become increasingly ineffective. At that time, subsequent treatment processes will be planned and initiated. It should be noted that the processes and anticipated costs associated with these processes are preliminary. Detailed engineering has not been performed, and approval for these methods has not been obtained from the regulator or the sponsors.

  5. Microwave cavity studies for thermal testing of ceramic breeder materials

    SciTech Connect

    Kuston, R.L.

    1987-01-01

    Dielectric heating of proposed ceramic tritium breeder material to study the thermomechanical and thermal-hydraulic properties of the material has been previously suggested. Recent computer studies using codes capable of modeling three-dimensional EM cavities with enclosed dielectric material have been used to determine the size limitations of cavity designs at 200 MHz. The sample can be as large as 0.44 /times/ 0.72m in the plane that is transverse to the direction of neutron flux. The uniformity of volumetric heating over the transverse plane is constant to within a few percent. The sample can be as long as 10cm in the direction of the heat flux and match the expected exponential decay of heat generation, exp( /minus/z/lambda), to within +/minus/8%. The design of the chamber is decribed, including the sample region, additional dielectric loading blocks on two sides of the sample region that are required to generate the field uniformity in the transverse plane, and a description of the matching-section portion of the cavity which provides the correct geometry to cause the cavity to resonate at 200 MHz with the right z dependence to stimulate the exponentially-decaying heat profile in the sample region. The matching section consists of two dielectric slabs, one on each wall of the chamber, and an air or free space region in the center of the matching section. The coupling loop is located near the wall end of the matching section in the free space region. 7 refs., 2 figs.

  6. Influence of canthaxanthin on broiler breeder reproduction, chick quality, and performance.

    PubMed

    Zhang, W; Zhang, K Y; Ding, X M; Bai, S P; Hernandez, J M; Yao, B; Zhu, Q

    2011-07-01

    To investigate the effect of canthaxanthin supplied via a maternal route on the production of both breeder hens and chickens, 270 Chinese Three-Yellow breeder hens were randomly divided into 2 groups consisting of 135 birds each (5 replicates of 27) for study. The breeder hens were fed either a basal diet or the basal diet supplemented with 6 mg of canthaxanthin/kg for 24 wk. At the end of the 24-wk breeder experiment, all hatching eggs laid in 5 consecutive days of each group were collected and incubated. For each breeder group, 100 newly hatched chicks (5 replicates of 20) were reared under environmentally controlled conditions for 21 d. Canthaxanthin supplementation resulted in the following outcomes: an enhancement of the serum total antioxidant capacity (TAC) of breeder hens (P = 0.029), a significant increase in the yolk colorimetric score of Roche Yolk Color Fan (RYCF; P < 0.001), and a significant improvement of the antioxidant status of the egg yolk (P < 0.05). The chicks that hatched from eggs laid by breeder hens fed the canthaxanthin supplementation diet demonstrated a higher pigmentation colorimetric score of RYCF for their shank skin (P < 0.05), and the antioxidant capacity of the newly hatched chicks was significantly increased (P < 0.05). Both of these positive effects on shank skin pigmentation colorimetric score of RYCF and antioxidant capacity were observed for at least 7 d posthatching, and the chicks that hatched from canthaxanthin-enriched eggs showed a lower mortality (0 vs. 4%) during the first 21 d posthatching. These findings support the hypothesis that canthaxanthin supplementation of the maternal diet enhances the protective capacity of tissues against oxidative stress in vivo, which might be beneficial for poultry producers. PMID:21673167

  7. Effects of breeder age on mineral contents and weight of yolk sac, embryo development, and hatchability in Pekin ducks.

    PubMed

    Onbasilar, E E; Erdem, E; Hacan, O; Yalçin, S

    2014-02-01

    The current study was carried out to investigate the effects of breeder age on egg composition, changes of embryo, yolk sac, and yolk minerals during incubation and hatchability in Pekin ducks. A total of 495 freshly laid eggs were obtained from the same flock of Pekin ducks, aged 28, 34, and 40 wk, and were reared in accordance with the management guide of the duck breeders (Star 53-Grimaud Freres). At each breeder age, egg measurements were made on a random subsample of unincubated eggs. Embryo and yolk sac measurements were made on embryonic day (E) 12, E16, E20, and E25. On d 28 of incubation, the healthy ducklings were removed and sex of chicks was determined. All chicks were weighed and hatching results were determined. Egg weight and yolk percentages increased; however, albumen percentages, shell thickness, and yolk index decreased as the flock aged. Shell percentages, shell breaking strength, albumen index, and haugh units were not affected by breeder age. Also, breeder age affected the Mg, P, K, Ca, Cu, and Zn levels in the yolk, except for Na level on day of setting, and breeder age affected the mineral consumed by embryo during incubation. However, on E25, the levels of examined minerals, except for P level in the yolk sac, were not statistically different in duck breeder age groups. Relative yolk sac and embryo weights of eggs obtained from different breeder ages varied from E16 to E25; however, embryo length was different in breeder age groups from E12 to E20. Hatching weight was affected by breeder age and sex. Hatching results were not different among breeder age groups. This study indicates that breeder age is important for some egg characteristics, relative yolk sac weight, some contents of minerals in the yolk, embryonic growth during incubation, and duckling weight. PMID:24570471

  8. Installation of the Light-Water Breeder Reactor at the Shippingport Atomic Power Station (LWBR Development Program)

    SciTech Connect

    Massimino, R.J.; Williams, D.A.

    1983-05-01

    This report summarizes the refueling operations performed to install a Light Water Breeder Reactor (LWBR) core into the existing pressurized water reactor vessel at the Shippingport Atomic Power Station. Detailed descriptions of the major installation operations (e.g., primary system preconditioning, fuel installation, pressure boundary seal welding) are included as appendices to this report; these operations are of technical interest to any reactor servicing operation, whether the reactor is a breeder or a conventional light water non-breeder core.

  9. Innovation Networks

    NASA Astrophysics Data System (ADS)

    Pyka, Andreas; Scharnhorst, Andrea

    The idea for this book started when we organized a topical workshop entitled "Innovation Networks - New Approaches in Modeling and Analyzing" (held in Augsburg, Germany in October 2005), under the auspices of Exystence, a network of excellence funded in the European Union's Fifth Framework Program. Unlike other conferences on innovation and networks, however, this workshop brought together scientists from economics, sociology, communication science, science and technology studies, and physics. With this book we aim to build further on a bridge connecting the bodies of knowledge on networks in economics, the social sciences and, more recently, statistical physics.

  10. Mathematical Innovation

    NASA Technical Reports Server (NTRS)

    1999-01-01

    Through Small Business Innovation Research funds from the Stennis Space Center, MathSoft, Inc., developed a system that can provide the building blocks for signal analysis and rapid prototyping. The product is the result of work to help NASA develop a complete understanding propulsion test data by using time frequency displays, automatic estimation and denoising, and data analysis plots for wavelet decomposition.

  11. Accelerating Innovation

    ERIC Educational Resources Information Center

    Education Week, 2012

    2012-01-01

    The word "innovation" seems to be in everyone's lexicon these days; it's even turning up as part of new education job titles in school districts and states. The ideas that undergird it are animating a growing movement that's spurring new policies, programs, and products that carry with them the potential to transform how students learn and how…

  12. Accident analysis of heavy water cooled thorium breeder reactor

    NASA Astrophysics Data System (ADS)

    Yulianti, Yanti; Su'ud, Zaki; Takaki, Naoyuki

    2015-04-01

    Thorium has lately attracted considerable attention because it is accumulating as a by-product of large scale rare earth mining. The objective of research is to analyze transient behavior of a heavy water cooled thorium breeder that is designed by Tokai University and Tokyo Institute of Technology. That is oxide fueled, PWR type reactor with heavy water as primary coolant. An example of the optimized core has relatively small moderator to fuel volume ratio (MFR) of 0.6 and the characteristics of the core are burn-up of 67 GWd/t, breeding ratio of 1.08, burn-up reactivity loss during cycles of < 0.2% dk/k, and negative coolant reactivity coefficient. One of the nuclear reactor accidents types examined here is Unprotected Transient over Power (UTOP) due to withdrawing of the control rod that result in the positive reactivity insertion so that the reactor power will increase rapidly. Another accident type is Unprotected Loss of Flow (ULOF) that caused by failure of coolant pumps. To analyze the reactor accidents, neutron distribution calculation in the nuclear reactor is the most important factor. The best expression for the neutron distribution is the Boltzmann transport equation. However, solving this equation is very difficult so that the space-time diffusion equation is commonly used. Usually, space-time diffusion equation is solved by employing a point kinetics approach. However, this approach is less accurate for a spatially heterogeneous nuclear reactor and the nuclear reactor with quite large reactivity input. Direct method is therefore used to solve space-time diffusion equation which consider spatial factor in detail during nuclear reactor accident simulation. Set of equations that obtained from full implicit finite-difference method is solved by using iterative methods. The indication of UTOP accident is decreasing macroscopic absorption cross-section that results large external reactivity, and ULOF accident is indicated by decreasing coolant flow. The

  13. Accident analysis of heavy water cooled thorium breeder reactor

    SciTech Connect

    Yulianti, Yanti; Su’ud, Zaki; Takaki, Naoyuki

    2015-04-16

    Thorium has lately attracted considerable attention because it is accumulating as a by-product of large scale rare earth mining. The objective of research is to analyze transient behavior of a heavy water cooled thorium breeder that is designed by Tokai University and Tokyo Institute of Technology. That is oxide fueled, PWR type reactor with heavy water as primary coolant. An example of the optimized core has relatively small moderator to fuel volume ratio (MFR) of 0.6 and the characteristics of the core are burn-up of 67 GWd/t, breeding ratio of 1.08, burn-up reactivity loss during cycles of < 0.2% dk/k, and negative coolant reactivity coefficient. One of the nuclear reactor accidents types examined here is Unprotected Transient over Power (UTOP) due to withdrawing of the control rod that result in the positive reactivity insertion so that the reactor power will increase rapidly. Another accident type is Unprotected Loss of Flow (ULOF) that caused by failure of coolant pumps. To analyze the reactor accidents, neutron distribution calculation in the nuclear reactor is the most important factor. The best expression for the neutron distribution is the Boltzmann transport equation. However, solving this equation is very difficult so that the space-time diffusion equation is commonly used. Usually, space-time diffusion equation is solved by employing a point kinetics approach. However, this approach is less accurate for a spatially heterogeneous nuclear reactor and the nuclear reactor with quite large reactivity input. Direct method is therefore used to solve space-time diffusion equation which consider spatial factor in detail during nuclear reactor accident simulation. Set of equations that obtained from full implicit finite-difference method is solved by using iterative methods. The indication of UTOP accident is decreasing macroscopic absorption cross-section that results large external reactivity, and ULOF accident is indicated by decreasing coolant flow. The

  14. Modelling of tritium transport in a pin-type solid breeder blanket

    SciTech Connect

    Martin, R.; Ghoniem, N.M.

    1986-02-01

    This study supplements a larger study of a solid breeder blanket design featuring lithium ceramic pins. This aspect of the study looks at tritium transport, release, and inventory within this blanket design. Li/sub 2/O and ..gamma..-LiAlO/sub 2/ are the two primary candidates for ceramic solid breeders. ..gamma..-LiAlO/sub 2/ was chosen for this blanket design due to its higher structural stability. Analysis of tritium behavior in solid breeder blankets is of great importance due to its impact on several critical issues: the generation of an adequate amount of fusion fuel, the safety-related issue of keeping radioactive blanket inventories as low as possible, and the release, purge, and economical processing of the bred tritium without undue contamination of the coolant and other reactor structures.

  15. Optimization of electron-cyclotron-resonance charge-breeder ions : Final CRADA Report.

    SciTech Connect

    Pardo, R.; Physics; Far-Tech, Inc.

    2009-10-09

    Measurements of 1+ beam properties and associated performance of ECR Charge Breeder source determined by total efficiency measurement and charge state distributions from the ECR Charge Breeder. These results were communicated to Far-Tech personnel who used them to benchmark the newly developed programs that model ion capture and charge breeding in the ECR Charge Breeder Source. Providing the basic data described above and in the discussion below to Far-Tech allowed them to improve and refine their calculational tools for ECR ion sources. These new tools will be offered for sale to industry and will also provide important guidance to other research labs developing Charge Breeding ion sources for radioactive beam physics research.

  16. Innovating Firms and Aggregate Innovation.

    ERIC Educational Resources Information Center

    Klette, Tor Jakob; Kortum, Samuel

    2004-01-01

    We develop a parsimonious model of innovation to confront firm-level evidence. It captures the dynamics of individual heterogeneous firms, describes the behavior of an industry with firm entry and exit, and delivers a general equilibrium model of technological change. While unifying the theoretical analysis of firms, industries, and the aggregate…

  17. Status and perspective of the R&D on ceramic breeder materials for testing in ITER

    NASA Astrophysics Data System (ADS)

    Ying, A.; Akiba, M.; Boccaccini, L. V.; Casadio, S.; Dell'Orco, G.; Enoeda, M.; Hayashi, K.; Hegeman, J. B.; Knitter, R.; van der Laan, J.; Lulewicz, J. D.; Wen, Z. Y.

    2007-08-01

    The main line of ceramic breeder materials research and development is based on the use of the breeder material in the form of pebble beds. At present, there are three candidate pebble materials (Li 4SiO 4, and two forms of Li 2TiO 3) for DEMO reactors that will be used for testing in ITER. This paper reviews the R&D of as-fabricated pebble materials against the blanket performance requirements and makes recommendations on necessary steps toward the qualification of these materials for testing in ITER.

  18. Breeder Spent Fuel Handling (BSFH) cask study for FY83. Final report

    SciTech Connect

    Diggs, J M

    1985-01-01

    This report documents a study conducted to investigate the applicability of existing LWR casks to shipment of long-cooled LMFBR fuel from the Clinch River Breeder Reactor Plant (CRBRP) to the Breeder Reprocessing Engineering Test (BRET) Facility. This study considered a base case of physical constraints of plants and casks, handling capabilities of plants, through-put requirements, shielding requirements due to transportation regulation, and heat transfer capabilities of the cask designs. Each cask design was measured relative to the base case. 15 references, 4 figures, 6 tables.

  19. Performance of the Argonne National Laboratory electron cyclotron resonance charge breeder

    SciTech Connect

    Vondrasek, R.; Kolomiets, A.; Levand, A.; Pardo, R.; Savard, G.; Scott, R.

    2011-05-15

    An electron cyclotron resonance charge breeder for the Californium rare ion breeder upgrade (CARIBU), a new radioactive beam facility for the Argonne Tandem Linac Accelerator System (ATLAS), has been constructed and commissioned. Charge breeding efficiencies up to 15.6% have been realized for stable beams with a typical breeding time of 10 ms/charge state. The CARIBU system has been undergoing commissioning tests utilizing a 100 mCi {sup 252}Cf fission source. A charge breeding efficiency of 14.8 {+-} 5% has been achieved for the first radioactive beam of {sup 143}Cs{sup 27+}.

  20. Comparative assessment of nuclear fuel cycles. Light-water reactor once-through, classical fast breeder reactor, and symbiotic fast breeder reactor cycles

    SciTech Connect

    Hardie, R.W.; Barrett, R.J.; Freiwald, J.G.

    1980-06-01

    The object of the Alternative Nuclear Fuel Cycle Study is to perform comparative assessments of nuclear power systems. There are two important features of this study. First, this evaluation attempts to encompass the complete, integrated fuel cycle from mining of uranium ore to disposal of waste rather than isolated components. Second, it compares several aspects of each cycle - energy use, economics, technological status, proliferation, public safety, and commercial potential - instead of concentrating on one or two assessment areas. This report presents assessment results for three fuel cycles. These are the light-water reactor once-through cycle, the fast breeder reactor on the classical plutonium cycle, and the fast breeder reactor on a symbiotic cycle using plutonium and /sup 233/U as fissile fuels. The report also contains a description of the methodology used in this assessment. Subsequent reports will present results for additional fuel cycles.

  1. The Impact of Yeast Culture Residue on the Suppression of Dietary Aflatoxin on the Performance of Broiler Breeder Hens

    Technology Transfer Automated Retrieval System (TEKTRAN)

    A study was conducted to examine the effect of yeast culture residue (YCR) on the suppression of aflatoxicosis in broiler breeder hens. One hundred twenty, 35-wk-old, Cobb broiler breeder hens of the same cross were fed diets supplemented with aflatoxin (AF) (0 or 3 mg/kg) and YCR (0 or 2 lb/ton) s...

  2. Challenges and Opportunities Associated with Simultaneous Energy Cane and Sugarcane Genetic Improvement -- Results of a Survey of International Sugarcane Breeders

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Following Brazil's dramatic success in utilizing sugarcane (Saccharum spp.) for large-scale ethanol production, and with a growing interest in energy crops worldwide, sugarcane breeders have been charged with genetically improving cane as an energy crop. We conducted a survey of sugarcane breeders i...

  3. Food residue recycling by swine breeders in a developing economy: a case study in Da Nang, Viet Nam.

    PubMed

    Kato, Takaaki; Pham, Dung Thi Xuan; Hoang, Hai; Xue, Yonghai; Tran, Quang Van

    2012-12-01

    This study provides a detailed description of food residue collection by swine breeders in Da Nang, Viet Nam. In January 2011, the study surveyed 30 swine breeders in two villages with respect to locations, methods, prices, quantities, and prospects for food residue collection. The sampled swine breeders regularly visited 55 locations in central Da Nang to collect raw food residue. They then transferred the food residue to their piggeries, boiled it, and fed it to their swine. A regression analysis revealed that the total amount of food residue collected by a farm depends on the number of swine in the farm and the number of collections made per day. Swine breeders in Da Nang were estimated to collect 26.3 metric tons of organic waste per day, which amounted to 4.1% of domestic waste collected by the local government. Among the sampled swine breeders, 93% answered that they would continue using food residue for the next five years. PMID:22883688

  4. Concept for a small, colocated fuel cycle facility for oxide breeder fuels

    SciTech Connect

    Burch, W.D.; Lerch, R.E.; Stradley, J.G.

    1987-01-01

    As part of a United States Department of Energy (USDOE) program to examine innovative liquid-metal reactor (LMR) system designs over the past three years, the Oak Ridge National Laboratory (ORNL) and the Westinghouse Hanford Company (WHC) collaborated on studies of mixed oxide fuel cycle options. A principal effort was an advanced concept for a small integrated fuel cycle colocated with a 1300-MW(e) reactor station. The study provided a scoping design, capital and operating cost estimates, and a basis on which to proceed with implementation of such a facility if future plans so dictate. The facility integrated reprocessing, waste management, and refabrication functions in a single facility of nominal 35-t/year capacity utilizing the latest technology developed in fabrication programs at WHC and in reprocessing at ORNL. The concept was based on many years of work at both sites and extensive design studies of prior years.

  5. Concept for a small, colocated fuel cycle facility for oxide breeder fuels

    SciTech Connect

    Burch, W.D.; Stradley, J.G.; Lerch, R.E.

    1987-01-01

    As part of a United States Department of Energy (USDOE) program to examine innovative liquid-metal reactor (LMR) system designs over the past three years, the Oak Ridge National Laboratory (ORNL) and the Westinghouse Hanford Company (WHC) collaborated on studies of mixed oxide fuel cycle options. A principal effort was an advanced concept for a small integrated fuel cycle colocated with a 1300-MW(e) reactor station. The study provided a scoping design and a basis on which to proceed with implementation of such a facility if future plans so dictate. The facility integrated reprocessing, waste management, and refabrication functions in a single facility of nominal 35-t/year capacity utilizing the latest technology developed in fabrication programs at WHC and in reprocessing at ORNL. The concept was based on many years of work at both sites and extensive design studies of prior years.

  6. Sperm production and testicular development of broiler breeder males reared on shortened growth cycles

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Feed restriction is an important tool used in the rearing of broiler breeders to control growth and maintain body weight. Feed restriction during the growing phase typically provides 60-80% less than what birds would consume if provided feed ad libitum, resulting in a perceived animal welfare issu...

  7. Sequencing analysis of Mycoplasma gallisepticum wild strains in vaccinated chicken breeder flocks.

    PubMed

    Khalifa, Rabab; Eissa, Sabry; El-Hariri, Mahmoud; Refai, Mohamed

    2014-01-01

    Mycoplasma gallisepticum (MG) infection is still of continuing economic concern in commercial broiler breeder chicken flocks in Egypt. MG infection continues to emerge despite the application of vaccination programs in breeder flocks. This prompted flock surveillance including MG isolation and molecular characterization of the circulating MG strains. The present study was concerned with 15 broiler breeder flocks of different ages (5-51 weeks). Three flocks were apparently healthy and 12 flocks were diseased. The aim of the study was to characterize the MG strains recovered from tracheal swabs. Four positive MG DNA extracts identified by rt-PCR and confirmed by isolation were subjected to sequencing of the mgc2 gene and intergenic spacer region (IGSR). The current molecular study demonstrated the presence of 3 different wild-type MG strains (RabE1-08, RabE2-09 and RabE3-09) in vaccinated diseased flocks, while the fourth strain (RabE4-08), which was isolated from a nonvaccinated apparently healthy breeder flock, scored 100% of homology and similarity to the F-strain vaccine by the sequence analysis of mgc2 and IGSR. It can be assumed that the vaccine F strain, which is supposed to replace field strains not only failed to do that, but also infected nonvaccinated flocks. Accordingly, there is a need to revise the control program including vaccine strategy in parallel with biosecurity measures. PMID:24525899

  8. Recommendations concerning models and parameters best suited to breeder reactor environmental radiological assessments

    SciTech Connect

    Miller, C.W.; Baes, C.F. III; Dunning, D.E. Jr.

    1980-05-01

    Recommendations are presented concerning the models and parameters best suited for assessing the impact of radionuclide releases to the environment by breeder reactor facilities. These recommendations are based on the model and parameter evaluations performed during this project to date. Seven different areas are covered in separate sections.

  9. Nuclear breeder reactor fuel element with axial tandem stacking and getter

    DOEpatents

    Gibby, Ronald L.; Lawrence, Leo A.; Woodley, Robert E.; Wilson, Charles N.; Weber, Edward T.; Johnson, Carl E.

    1981-01-01

    A breeder reactor fuel element having a tandem arrangement of fissile and fertile fuel with a getter for fission product cesium disposed between the fissile and fertile sections. The getter is effective at reactor operating temperatures to isolate the cesium generated by the fissile material from reacting with the fertile fuel section.

  10. Breeder survey, tools, and resources to visualize diversity and pedigree relationships at MaizeGDB

    Technology Transfer Automated Retrieval System (TEKTRAN)

    In collaboration with maize researchers, the MaizeGDB Team prepared a survey to identify breeder needs for visualizing pedigrees, diversity data, and haplotypes, and distributed it to the maize community on behalf of the Maize Genetics Executive Committee (Summer 2015). We received 48 responses from...

  11. The Role of Feeding Regimens in Regulating Metabolism of Sexually Mature Broiler Breeders

    Technology Transfer Automated Retrieval System (TEKTRAN)

    A trial was conducted to determine the effects of different rearing feed regimens on plasma hormone and metabolite levels and hepatic lipid metabolism and gene expression on sexually mature broiler breeders. Cobb 500 birds were divided into two groups at 4 weeks of age and fed either everyday (ED) ...

  12. Atoms in Appalachia. Historical report on the Clinch River Breeder Reactor site

    SciTech Connect

    Schaffer, D

    1982-01-01

    The background information concerning the acquisition of the land for siting the Clinch River Breeder Reactor is presented. Historical information is also presented concerning the land acquisition for the Oak Ridge facilities known as the Manhattan Project during World War II.

  13. Mating behavior and fertility of broiler breeder males reared on shortened growth cycles

    Technology Transfer Automated Retrieval System (TEKTRAN)

    One of the more difficult tasks when raising broiler breeder cockerels is controlling weight gain in the rearing house without inflicting excess stress. This is a period of time for the young male when many portions of reproductive system are in the formative stages and, if neglected, can have lif...

  14. Materials data base and design equations for the UCLA solid breeder blanket

    SciTech Connect

    Sharafat, S.; Amodeo, R.; Ghoniem, N.M.

    1986-02-01

    The materials and properties investigated for this blanket study are listed. The phenomenological equations and mathematical fits for all materials and properties considered are given. Efforts to develop a swelling equation based on the few experimental data points available for breeder materials are described. The sintering phenomena for ceramics is investigated.

  15. Ionization efficiency studies with charge breeder and conventional electron cyclotron resonance ion source

    SciTech Connect

    Koivisto, H. Tarvainen, O.; Toivanen, V.; Komppula, J.; Kronholm, R.; Lamy, T.; Angot, J.; Delahaye, P.; Maunoury, L.; Patti, G.; Standylo, L.; Steczkiewicz, O.; Choinski, J.

    2014-02-15

    Radioactive Ion Beams play an increasingly important role in several European research facility programs such as SPES, SPIRAL1 Upgrade, and SPIRAL2, but even more for those such as EURISOL. Although remarkable advances of ECRIS charge breeders (CBs) have been achieved, further studies are needed to gain insight on the physics of the charge breeding process. The fundamental plasma processes of charge breeders are studied in the frame of the European collaboration project, EMILIE, for optimizing the charge breeding. Important information on the charge breeding can be obtained by conducting similar experiments using the gas mixing and 2-frequency heating techniques with a conventional JYFL 14 GHz ECRIS and the LPSC-PHOENIX charge breeder. The first experiments were carried out with noble gases and they revealed, for example, that the effects of the gas mixing and 2-frequency heating on the production of high charge states appear to be additive for the conventional ECRIS. The results also indicate that at least in the case of noble gases the differences between the conventional ECRIS and the charge breeder cause only minor impact on the production efficiency of ion beams.

  16. Innovation: It's Academic.

    ERIC Educational Resources Information Center

    Long, Carl

    1988-01-01

    Discusses the development of innovation and business incubators, including the stages of innovation typically addressed by such programs. Describes the efforts of the Thayer School, a graduate professional school at Dartmouth College, in establishing an innovation incubator. (TW)

  17. Design and technology development of solid breeder blanket cooled by supercritical water in Japan

    NASA Astrophysics Data System (ADS)

    Enoeda, M.; Kosaku, Y.; Hatano, T.; Kuroda, T.; Miki, N.; Honma, T.; Akiba, M.; Konishi, S.; Nakamura, H.; Kawamura, Y.; Sato, S.; Furuya, K.; Asaoka, Y.; Okano, K.

    2003-12-01

    This paper presents results of conceptual design activities and associated R&D of a solid breeder blanket system for demonstration of power generation fusion reactors (DEMO blanket) cooled by supercritical water. The Fusion Council of Japan developed the long-term research and development programme of the blanket in 1999. To make the fusion DEMO reactor more attractive, a higher thermal efficiency of more than 40% was strongly recommended. To meet this requirement, the design of the DEMO fusion reactor was carried out. In conjunction with the reactor design, a new concept of a solid breeder blanket cooled by supercritical water was proposed and design and technology development of a solid breeder blanket cooled by supercritical water was performed. By thermo-mechanical analyses of the first wall, the tresca stress was evaluated to be 428 MPa, which clears the 3Sm value of F82H. By thermal and nuclear analyses of the breeder layers, it was shown that a net TBR of more than 1.05 can be achieved. By thermal analysis of the supercritical water power plant, it was shown that a thermal efficiency of more than 41% is achievable. The design work included design of the coolant flow pattern for blanket modules, module structure design, thermo-mechanical analysis and neutronics analysis of the blanket module, and analyses of the tritium inventory and permeation. Preliminary integration of the design of a solid breeder blanket cooled by supercritical water was achieved in this study. In parallel with the design activities, engineering R&D was conducted covering all necessary issues, such as development of structural materials, tritium breeding materials, and neutron multiplier materials; neutronics experiments and analyses; and development of the blanket module fabrication technology. Upon developing the fabrication technology for the first wall and box structure, a hot isostatic pressing bonded F82H first wall mock-up with embedded rectangular cooling channels was

  18. Effects of environmental temperature and dietary energy on energy partitioning coefficients of female broiler breeders.

    PubMed

    Pishnamazi, A; Renema, R A; Paul, D C; Wenger, I I; Zuidhof, M J

    2015-10-01

    With increasing disparity between broiler breeder target weights and broiler growth potential, maintenance energy requirements have become a larger proportion of total broiler breeder energy intake. Because energy is partitioned to growth and egg production at a lower priority than maintenance, accurate prediction of maintenance energy requirements is important for practical broiler breeder feed allocation decisions. Environmental temperature affects the maintenance energy requirement by changing rate of heat loss to the environment. In the ME system, heat production (energy lost) is part of the maintenance requirement (ME). In the current study, a nonlinear mixed model was derived to predict ME partitioning of broiler breeder hens under varied temperature conditions. At 21 wk of age, 192 Ross 708 hens were individually caged within 6 controlled environmental chambers. From 25 to 41 wk, 4 temperature treatments (15°C, 19°C, 23°C, and 27°C) were randomly assigned to the chambers for 2-week periods. Half of the birds in each chamber were fed a high-energy (HE; 2,912 kcal/kg) diet, and half were fed a low-energy (LE; 2,790 kcal/kg) diet. The nonlinear mixed regression model included a normally distributed random term representing individual hen maintenance, a quadratic response to environmental temperature, and linear ADG and egg mass (EM) coefficients. The model assumed that energy requirements for BW gain and egg production were not influenced by environmental temperature because hens were homeothermic, and the cellular processes for associated biochemical processes occurred within a controlled narrow core body temperature range. Residual feed intake (RFI) and residual ME (RME) were used to estimate efficiency. A quadratic effect of environmental temperature on broiler breeder MEm was predicted ( < 0.0001), with a minimum energy expenditure at 24.3°C. Predicted ME at 21°C was 92.5 kcal/kg; requirements for gain and EM were 2.126 and 1.789 kcal/g, respectively

  19. Accommodation of liquid metal by cavity liners

    SciTech Connect

    Jeppson, D.W.

    1989-03-01

    Present liquid metal breeder reactor cell liner designs appear adequate to contain postulated leakages of lithium-lead alloy in an air or steam atmosphere and to contain lithium when inert atmospheres are present. If an air or steam atmosphere may be present in a cavity where lithium amy accumulate under postulated accident conditions, then consideration of stainless steel liners and further testing is recommended. Lithium testing of faulted liners should also be considered. SOFIRE II and WATRe computer codes may be useful in establishing liner design requirements and in determining water release from concrete behind the liners (potential hydrogen production) for postulated leakages to steel-lined concrete cavities.

  20. Apparatus for detecting leakage of liquid sodium

    DOEpatents

    Himeno, Yoshiaki

    1978-01-01

    An apparatus for detecting the leakage of liquid sodium includes a cable-like sensor adapted to be secured to a wall of piping or other equipment having sodium on the opposite side of the wall, and the sensor includes a core wire electrically connected to the wall through a leak current detector and a power source. An accidental leakage of the liquid sodium causes the corrosion of a metallic layer and an insulative layer of the sensor by products resulted from a reaction of sodium with water or oxygen in the atmospheric air so as to decrease the resistance between the core wire and the wall. Thus, the leakage is detected as an increase in the leaking electrical current. The apparatus is especially adapted for use in detecting the leakage of liquid sodium from sodium-conveying pipes or equipment in a fast breeder reactor.

  1. End-of-life nondestructive examination of Light Water Breeder Reactor fuel rods (LWBR Development Program)

    SciTech Connect

    Gorscak, D.A.; Campbell, W.R.; Clayton, J.C.

    1987-10-01

    In-bundle and out-of-bundle (single rod) nondestructive examinations of Light Water Breeder Reactor fuel rods were performed. In-bundle examinations included visual examination and measurement of rod bow, rod-to-rod gaps, and rod removal forces. Out-of-bundle examinations included rod visuals and measurement of fuel rod length, diameter and ovality, cladding oxide and crud thickness, support grid induced cladding wear mark depth and volume, and fuel rod free hanging bow. The out-of-bundle examination also included ultrasonic inspection for cladding defects, neutron radiography for pellet integrity and plenum gap measurements, and gamma scans for instack axial gap screening and binary fuel stack length measurements. The measurements confirmed design predictions of fuel rod performance and provided evidence of excellent fuel rod performance for operation of Light Water Breeder Reactor to 29,047 effective full power hours (EFPH).

  2. Effect of lycopene on semen quality, fertility and native immunity of broiler breeder.

    PubMed

    Mangiagalli, M G; Martino, P A; Smajlovic, T; Guidobono Cavalchini, L; Marelli, S P

    2010-02-01

    1. The effect of drinking water supplementation with lycopene on the semen quality, fertility and immunity of broiler breeders was evaluated. 2. Broiler breeder males were individually caged from 25 to 42 weeks old and divided into two group: L group, treated birds (lycopene 0.5 g/l) and C group, control birds. Laying hens were divided into two groups and artificially inseminated. 3. Semen variables were evaluated and daily fertility recorded. Serum bactericidal activity was tested. 4. Semen production and viability were affected by lycopene supplementation. Serum bactericidal activity was better in L than in C group. The fertility rate curve of the L group displayed a positive trend. PMID:20390581

  3. Activation characteristics of a solid breeder blanket for a fusion power demonstration reactor

    NASA Astrophysics Data System (ADS)

    Fischer, Ulrich; Tsige-Tamirat, Haileyesus

    2002-12-01

    Activation characteristics have been assessed for a helium cooled solid breeder blanket on the basis of three-dimensional activation calculations for a 2200 MW fusion power demonstration reactor. FISPACT inventory calculations were performed for the beryllium neutron multiplier, the Li 4SiO 4 breeder ceramics and the Eurofer low activation steel. Neutron flux spectra distributions were provided by a previous MCNP calculation. Detailed spatial distributions have been obtained for the nuclide inventories and related quantities such as activity, decay heat and contact dose rate. These data are available form the authors upon request. On the basis of the calculated contact gamma dose rates, the waste quality was assessed with regard to a possible re-use of the activated materials following the remote or the hands-on handling recycling options.

  4. Neutronics Analysis of Water-Cooled Ceramic Breeder Blanket for CFETR

    NASA Astrophysics Data System (ADS)

    Zhu, Qingjun; Li, Jia; Liu, Songlin

    2016-07-01

    In order to investigate the nuclear response to the water-cooled ceramic breeder blanket models for CFETR, a detailed 3D neutronics model with 22.5° torus sector was developed based on the integrated geometry of CFETR, including heterogeneous WCCB blanket models, shield, divertor, vacuum vessel, toroidal and poloidal magnets, and ports. Using the Monte Carlo N-Particle Transport Code MCNP5 and IAEA Fusion Evaluated Nuclear Data Library FENDL2.1, the neutronics analyses were performed. The neutron wall loading, tritium breeding ratio, the nuclear heating, neutron-induced atomic displacement damage, and gas production were determined. The results indicate that the global TBR of no less than 1.2 will be a big challenge for the water-cooled ceramic breeder blanket for CFETR. supported by the National Magnetic Confinement Fusion Science Program of China (Nos. 2013GB108004, 2014GB122000, and 2014GB119000), and National Natural Science Foundation of China (No. 11175207)

  5. Clinical outbreak of Bordetella avium infection in two turkey breeder flocks.

    PubMed

    Kelly, B J; Ghazikhanian, G Y; Mayeda, B

    1986-01-01

    An acute upper respiratory disease was observed in two broad-breasted white (BBW) turkey primary breeder flocks. Associated clinical signs included sneezing, depression, and a deep dry cough originating from large conducting airways. Morbidity reached approximately 15-20% of the hens in an affected house. None of the turkeys died, and total feed consumption was not affected. A minimal effect upon egg production was noticed. Sera from an acutely affected flock exhibited a marked rise in titer to Bordetella avium compared with preinfection sera samples. In Case 1, B. avium was isolated in pure culture from affected birds. In Case 2, B. avium was diagnosed by serological results and clinical signs; bacteriological examination was not attempted. The findings presented here are consistent with an acute clinical outbreak of B. avium-induced turkey rhinotracheitis (turkey coryza) in BBW turkey breeder hens. PMID:3729868

  6. Characterization of advertisements for puppies sold online: determinants of cost and a comparison with parent club breeders.

    PubMed

    Voris, H C; Wittum, T E; Rajala-Schultz, P J; Lord, L K

    2011-07-01

    The Internet is an increasingly common way for consumers to purchase puppies. Yet very little information is available about the types of puppies sold via the Internet. In addition these sales are not subject to United States Depart of Agriculture (USDA) regulation. The objectives of the study were to describe puppies sold via the Internet, to assess the characteristics that contribute to the cost of a puppy, and to compare puppies sold via the Internet with puppies sold by American Kennel Club (AKC) Parent Club breeders. Over 14 weeks in 2008, Yorkshire Terrier, Shih Tzu, English Bulldog, Boxer, and Labrador Retriever puppies for sale on two large-scale online puppy sales sites were categorized based on their Internet advertisements. Data were collected in three categories: puppy characteristics, health characteristics, and policies (such as spay/neuter requirement, health guarantee, and return policy). After the survey was completed, 25 AKC Parent Club breeders and 25 other breeders who advertised via one of the puppy sales websites were randomly selected and interviewed over the phone. Small breed puppies were most frequently advertised with 35.2% (1228/3485) of advertisements for Yorkshire Terriers and 23.0% (802/3485) for Shih Tzus. Almost one quarter of Internet breeders 768/3474 (22.2%) advertised four or more different dog breeds. Champion bloodlines increased the cost of a puppy of all breeds. AKC Parent Club breeders 21/25 (84%) were more likely to mention breed-specific health screening tests when compared to Internet breeders 7/25 (28%). Consumers should apply the same standards for purchasing from a breeder found through a puppy sales site as they would for purchasing from a local breeder. Breeders who advertise at one of the large-scale puppy sales websites are less knowledgeable about breed-specific health issues compared to an AKC Parent Club breeder. Internet breeders are less likely to perform these screening tests on their breeding dogs and may

  7. Development of DIPRES feed for the fabrication of mixed-oxide fuels for fast breeder reactors

    SciTech Connect

    Griffin, C W; Rasmussen, D E; Lloyd, M H

    1983-01-01

    The DIrect PREss Spheroidized feed process combines the conversion of uranium-plutonium solutions into spheres by internal gelation with conventional pellet fabrication techniques. In this manner, gel spheres could replace conventional powders as the feed material for pellet fabrication of nuclear fuels. Objective of the DIPRES feed program is to develop and qualify a process to produce mixed-oxide fuel pellets from gel spheres for fast breeder reactors. This process development includes both conversion and fabrication activities.

  8. Conceptual design of the Clinch River Breeder Reactor spent-fuel shipping cask

    SciTech Connect

    Pope, R B; Diggs, J M

    1982-04-01

    Details of a baseline conceptual design of a spent fuel shipping cask for the Clinch River Breeder Reactor (CRBR) are presented including an assessment of shielding, structural, thermal, fabrication and cask/plant interfacing problems. A basis for continued cask development and for new technological development is established. Alternates to the baseline design are briefly presented. Estimates of development schedules, cask utilization and cost schedules, and of personnel dose commitments during CRBR in-plant handling of the cask are also presented.

  9. Vertical transmission and clinical signs in broiler breeders and broilers experiencing adenoviral gizzard erosion.

    PubMed

    Grafl, Beatrice; Aigner, Franz; Liebhart, Dieter; Marek, Ana; Prokofieva, Irina; Bachmeier, Josef; Hess, Michael

    2012-12-01

    The present report documents an outbreak of adenoviral gizzard erosion in 22 broiler flocks in Germany. The clinical picture was characterized by uneven growth of affected broilers that resulted in considerably lower than average weight at slaughtering. Fowl adenovirus serotype 1 (FAdV-1) was isolated from gizzard lesions and histological examinations demonstrated FAdV-1-positive intranuclear inclusion bodies in gizzard epithelial cells of affected broilers by in-situ hybridization. Birds from all affected flocks originated from one broiler breeder farm. During production of affected birds, broiler breeders were between 27 and 32 weeks old. Enzyme-linked immunosorbent assay and specific virus neutralization assay of sera from parent birds demonstrated an acute FAdV-1 infection within the first 5 weeks of the production cycle. Clinically, broiler breeders exhibited a moderate fall in the hatchability of their chicks, while egg production remained normal. No further clinical signs could be observed. Genetically identical FAdV-1 strains were isolated from gizzards of embryos at the lowest point of hatchability and from affected broiler flocks raised on independent farms. For the first time, direct detection of viable FAdV-1 from gizzards of embryos and progenies of one FAdV-1-seropositive broiler breeder farm in the course of an outbreak of adenoviral gizzard erosion could be demonstrated, highlighting the importance of vertical transmission of this disease. Additionally, growth retardation and subsequent reduced average weight at the time of slaughter of broiler chickens underline the economic impact of adenoviral gizzard erosion for poultry production. PMID:23237373

  10. What drives seasonal fluctuations of body condition in a semelparous income breeder octopus?

    NASA Astrophysics Data System (ADS)

    Quetglas, Antoni; Ordines, Francesc; Valls, Maria

    2011-09-01

    The vast majority of modern cephalopods is single-season breeders, or semelparous in the strict sense, that die soon after the reproduction takes place. Individual body condition in these marine invertebrates is expected to be highly affected by reproduction because: 1) the gonad weight of females, which represents <1% of body weight when immature, increases up to 20-50% during maturation; and 2) octopus females reduce or even cease their food intake during breeding. Based on this expectation, we analysed the interrelationship between condition and reproduction in the temperate octopus Eledone cirrhosa. Results from a previous work using biochemical analyses showed that reproduction in this species is not fuelled by stored reserves (capital breeder), but by food intakes (income breeder). Since income breeders depend strongly on food resources, the effect of several environmental variables related to food availability such as primary production, sea temperature (ST) and river discharges were also analysed. Condition showed a marked intrannual cycle independently of the sex and, noteworthy, the maturity stage. Given that immature individuals are not expected to display seasonal fluctuations in body condition related to maturation, these results preclude reproduction as a driving factor for the observed circannual cycle. Condition was significantly correlated with all the environmental variables analysed, except with ST at the depths where the species lives. Although this last result also precludes concurrent ST as a driving factor of body condition, those correlations suggest that condition might display an intrinsic seasonal cycle, as many other life-history traits in most species such as reproduction, migration or moulting. Finally, there also remains the possibility that condition in this octopus species is determined genetically, as has been reported in recent studies across different taxonomical groups.

  11. The relationship of spectral sensitivity with growth and reproductive response in avian breeders (Gallus gallus)

    PubMed Central

    Yang, Ye-Feng; Jiang, Jing-Song; Pan, Jin-Ming; Ying, Yi-Bin; Wang, Xiao-Shuang; Zhang, Ming-Li; Lu, Min-Si; Chen, Xian-Hui

    2016-01-01

    A previous study demonstrated that birds that are exposed to light at night develop advanced reproductive systems. However, spectrum might also affect the photoperiodic response of birds. The present study was aimed to investigate the effects of spectral composition on the growth and reproductive physiology of female breeders, using pure light-emitting diode spectra. A total of 1,000 newly hatched female avian breeders (Gallus gallus) were equally allocated to white-, red-, yellow-, green- and blue-light treated groups. We found that blue-light treated birds had a greater and faster weight gain than did red- and yellow-light treated birds (P = 0.02 and 0.05). The red light expedited the sexual maturation of the chicks, whose age at sexual maturity was 7 and 14 days earlier than that of the green- and blue-light treated birds, respectively. The accumulative egg production of the red-light treated birds was 9 and 8 eggs more than that of the blue- and green-light treated birds. The peak lay rate of the red-light treated groups was significantly greater than the blue-light treated birds (P = 0.028). In conclusion, exposure to short-wavelength light appears to promote growth of female breeder birds, whereas exposure to long-wavelength light appears to accelerate reproductive performance. PMID:26765747

  12. Design of the low energy beam transport line between CARIBU and the EBIS charge breeder

    NASA Astrophysics Data System (ADS)

    Perry, A.; Ostroumov, P. N.; Barcikowski, A.; Dickerson, C.; Kondrashev, S. A.; Mustapha, B.; Savard, G.

    2015-01-01

    An Electron Beam Ion Source Charge Breeder (EBIS-CB) has been developed to breed radioactive beams from the CAlifornium Rare Isotope Breeder Upgrade (CARIBU) facility at ATLAS. The EBIS-CB will replace the existing ECR charge breeder to increase the intensity and improve the purity of reaccelerated radioactive ion beams. The EBIS-CB is in the final stage of off-line commissioning. Currently, we are developing a low energy beam transport (LEBT) system to transfer CARIBU beams to the EBIS-CB. As was originally planned, an RFQ cooler-buncher will precede the EBIS-CB. Recently, it was decided to include a multi-reflection time-of-flight (MR-TOF) mass-spectrometer following the RFQ. MR-TOF is a relatively new technology used to purify beams with a mass-resolving power up to 3×105 as was demonstrated in experiments at CERN/ISOLDE. Very high purity singly-charged radioactive ion beams will be injected into the EBIS for charge breeding and due to its inherent properties, the EBIS-CB will maintain the purity of the charge bred beams. Possible contamination of residual gas ions will be greatly suppressed by achieving ultra-high vacuum in the EBIS trap. This paper will present and discuss the design of the LEBT and the overall integration of the EBIS-CB into ATLAS.

  13. Eradication of Mycoplasma synoviae from a multi-age broiler breeder farm using antibiotics therapy.

    PubMed

    Hong, Young-Ho; Kwon, Ji-Seon; Lee, Hyun-Jeong; Song, Chang-Seon; Lee, Sang-Won

    2015-10-01

    Mycoplasma synoviae (MS) is a common respiratory pathogen in the poultry industry. Eradication of MS from broiler breeder flocks is important for reducing economic losses caused by MS-associated diseases on broiler farms. An outbreak of MS infection was detected on a multi-age Korean broiler breeder farm that implements a flock replacement program every 3 to 6 months and uses A-type cages. Continuous administration of tilmicosin after 2 rounds of intensive antibiotics treatment with chlortetracycline, doxycycline, and enrofloxacin reduced MS shedding from the MS-positive flocks and eventually eradicated MS from the farm. Flock 3 was the last MS-positive flock by both PCR and enzyme-linked immunosorbent assay (ELISA), while flocks introduced to the farm after flock 3 were MS-negative by both PCR and ELISA at the time of depletion. This is the first report of successful eradication of MS from a multi-age broiler breeder farm using continuous antibiotic treatments. PMID:26240392

  14. The relationship of spectral sensitivity with growth and reproductive response in avian breeders (Gallus gallus).

    PubMed

    Yang, Ye-Feng; Jiang, Jing-Song; Pan, Jin-Ming; Ying, Yi-Bin; Wang, Xiao-Shuang; Zhang, Ming-Li; Lu, Min-Si; Chen, Xian-Hui

    2016-01-01

    A previous study demonstrated that birds that are exposed to light at night develop advanced reproductive systems. However, spectrum might also affect the photoperiodic response of birds. The present study was aimed to investigate the effects of spectral composition on the growth and reproductive physiology of female breeders, using pure light-emitting diode spectra. A total of 1,000 newly hatched female avian breeders (Gallus gallus) were equally allocated to white-, red-, yellow-, green- and blue-light treated groups. We found that blue-light treated birds had a greater and faster weight gain than did red- and yellow-light treated birds (P = 0.02 and 0.05). The red light expedited the sexual maturation of the chicks, whose age at sexual maturity was 7 and 14 days earlier than that of the green- and blue-light treated birds, respectively. The accumulative egg production of the red-light treated birds was 9 and 8 eggs more than that of the blue- and green-light treated birds. The peak lay rate of the red-light treated groups was significantly greater than the blue-light treated birds (P = 0.028). In conclusion, exposure to short-wavelength light appears to promote growth of female breeder birds, whereas exposure to long-wavelength light appears to accelerate reproductive performance. PMID:26765747

  15. Thermodynamic considerations for the use of vanadium alloys with ceramic breeder materials

    SciTech Connect

    Johnson, C.E.; Johnson, I.; Kopasz, J.P.

    1995-12-31

    Fusion energy is considered to be an attractive energy form because of its minimal environmental impact. In order to maintain this favorable status, every effort needs to be made to use low activation materials wherever possible. The tritium breeder blanket is a focal point of system design engineers who must design environmentally attractive blankets through the use of low activation materials. Of the several candidate lithium-containing ceramics being considered for use in the breeder blanket, Li{sub 2}O, Li{sub 2}TiO{sub 3}, are attractive choices because of their low activation. Also, low activation materials like the vanadium alloys are being considered for use as structural materials in the blanket. The suitability of vanadium alloys for containment of lithium ceramics is the subject of this study. Thermodynamic evaluations are being used to estimate the compatibility and stability of candidate ceramic breeder materials (Li{sub 2}O, Li{sub 2}TiO{sub 3}, and Li{sub 2}ZrO{sub 3}) with vanadium and vanadium alloys. This thermodynamic evaluation will focus first on solid-solid interactions. As a tritium breeding blanket will use a purge gas for tritium recovery, gas-solid systems will also receive attention.

  16. US-DOE Fusion-Breeder Program: blanket design and system performance

    SciTech Connect

    Lee, J.D.

    1983-01-01

    Conceptual design studies are being used to assess the technical and economic feasibility of fusion's potential to produce fissile fuel. A reference design of a fission-suppressed blanket using conventional materials is under development. Theoretically, a fusion breeder that incorporates this fusion-suppressed blanket surrounding a 3000-MW tandem mirror fusion core produces its own tritium plus 5600 kg of /sup 233/U per year. The /sup 233/U could then provide fissile makeup for 21 GWe of light-water reactor (LWR) power using a denatured thorium fuel cycle with full recycle. This is 16 times the net electric power produced by the fusion breeder (1.3 GWe). The cost of electricity from this fusion-fission system is estimated to be only 23% higher than the cost from LWRs that have makeup from U/sub 3/O/sub 8/ at present costs (55 $/kg). Nuclear performance, magnetohydrodynamics (MHD), radiation effects, and other issues concerning the fission-suppressed blanket are summarized, as are some of the present and future objectives of the fusion breeder program.

  17. The relationship of spectral sensitivity with growth and reproductive response in avian breeders (Gallus gallus)

    NASA Astrophysics Data System (ADS)

    Yang, Ye-Feng; Jiang, Jing-Song; Pan, Jin-Ming; Ying, Yi-Bin; Wang, Xiao-Shuang; Zhang, Ming-Li; Lu, Min-Si; Chen, Xian-Hui

    2016-01-01

    A previous study demonstrated that birds that are exposed to light at night develop advanced reproductive systems. However, spectrum might also affect the photoperiodic response of birds. The present study was aimed to investigate the effects of spectral composition on the growth and reproductive physiology of female breeders, using pure light-emitting diode spectra. A total of 1,000 newly hatched female avian breeders (Gallus gallus) were equally allocated to white-, red-, yellow-, green- and blue-light treated groups. We found that blue-light treated birds had a greater and faster weight gain than did red- and yellow-light treated birds (P = 0.02 and 0.05). The red light expedited the sexual maturation of the chicks, whose age at sexual maturity was 7 and 14 days earlier than that of the green- and blue-light treated birds, respectively. The accumulative egg production of the red-light treated birds was 9 and 8 eggs more than that of the blue- and green-light treated birds. The peak lay rate of the red-light treated groups was significantly greater than the blue-light treated birds (P = 0.028). In conclusion, exposure to short-wavelength light appears to promote growth of female breeder birds, whereas exposure to long-wavelength light appears to accelerate reproductive performance.

  18. Drug sensitivity of coccidia from broiler breeder pullets and from broilers in the same integrated company.

    PubMed

    Mathis, G F; McDougald, L R; McMurray, B

    1984-01-01

    Coccidia isolated from 12 breeder pullet farms and 18 broiler farms were tested for sensitivity to anticoccidial drugs. The species Eimeria acervulina, E. maxima, and E. tenella were common in the isolates and were fully pathogenic. Broiler coccidia were generally resistant to Zoalene but sensitive to nicarbazin. About half of the isolates had reduced sensitivity to amprolium and monensin. Most of the breeder pullet coccidia were resistant to Zoalene and amprolium, but almost all were highly sensitive to nicarbazin and monensin. There was some difference in responses of broiler isolates to various ionophores. Isolates responded best to salinomycin and lasalocid, which had not been previously used on the farms. Monensin controlled coccidia slightly better when given at 120 ppm than when given at 100 ppm. These results suggest that broiler coccidia have lost some responsiveness to ionophores as a result of long-term exposure, but that breeder pullet coccidia, which have never been exposed to those drugs, have retained their sensitivity. Resistance or sensitivity to other drugs was consistent with history of use: more isolates were sensitive to older drugs that had not been used for several years than was reported in previous surveys. PMID:6743177

  19. Age-related changes in gonadal and serotonergic axes of broiler breeder roosters.

    PubMed

    Avital-Cohen, N; Heiblum, R; Argov-Argaman, N; Rosenstrauch, A; Chaiseha, Y; Mobarkey, N; Rozenboim, I

    2013-04-01

    Fertility of domestic roosters decreases at ≈ 50 wk of age. In a previous study on aging white leghorn roosters, low fertility was accompanied by low levels of both hypothalamic vasoactive intestinal peptide (VIP) and pituitary prolactin (PRL) mRNA expression; however, their role in aging broiler breeder rooster reproduction is still unclear. In this study we compared reproductive activities of young (35-wk-old) and aging (73-wk-old) broiler breeder roosters. Weekly semen volume; concentration and ejaculation grade; and concentrations of plasma testosterone, estradiol, and PRL were examined. Every other week, 10 roosters from each group were euthanized, their testes weighed, and hypothalamus and pituitary removed to determine mRNA expression of hypothalamic GnRH-I, pituitary FSH, pituitary LH, hypothalamic VIP, and pituitary PRL. Aging roosters had significantly lower testis weight and semen volume, sperm concentration, ejaculation grade and plasma testosterone and low hypothalamic GnRH-I, pituitary FSH, and pituitary LH mRNA expression than young roosters (P ≤ 0.05). Aging roosters had higher concentrations of plasma estradiol and PRL and higher hypothalamic VIP and pituitary PRL mRNA expression than young roosters (P ≤ 0.05). We suggest that PRL, which is known to inhibit the gonadal axis, and its releasing factor, VIP, play an important role in the reproductive failure associated with age in broiler breeder roosters. PMID:23411011

  20. Electromagnetic analysis of the plasma chamber of an ECR-based charge breeder.

    PubMed

    Galatà, A; Patti, G; Celona, L; Mascali, D; Neri, L; Torrisi, G

    2016-02-01

    The optimization of the efficiency of an ECR-based charge breeder is a twofold task: efforts must be paid to maximize the capture of the injected 1+ ions by the confined plasma and to produce high charge states to allow post-acceleration at high energies. Both tasks must be faced by studying in detail the electrons heating dynamics, influenced by the microwave-to-plasma coupling mechanism. Numerical simulations are a powerful tools for obtaining quantitative information about the wave-to-plasma interaction process: this paper presents a numerical study of the microwaves propagation and absorption inside the plasma chamber of the PHOENIX charge breeder, which the selective production of exotic species project, under construction at Legnaro National Laboratories, will adopt as charge breeder. Calculations were carried out with a commercial 3D FEM solver: first, all the resonant frequencies were determined by considering a simplified plasma chamber; then, the realistic geometry was taken into account, including a cold plasma model of increasing complexity. The results gave important information about the power absorption and losses and will allow the improvement of the plasma model to be used in a refined step of calculation reproducing the breeding process itself. PMID:26932058

  1. A model for an economically optimal replacement of a breeder flock.

    PubMed

    Yassin, Hurria; Velthuis, Annet G J; Giesen, Gerard W J; Oude Lansink, Alfons G J M

    2012-12-01

    A deterministic model is developed to support the tactical and operational replacement decisions at broiler breeder farms. The marginal net revenue approach is applied to determine the optimal replacement age of a flock. The objective function of the model maximizes the annual gross margin over the flock's production cycle. To calculate the gross margin, future egg production, fertility, or hatchability of the eggs, revenues and variable costs of a flock were estimated. For tactical decisions, the optimal laying length is the age at which the average gross margin of an average flock is maximal. For operational decisions, a flock should be replaced when the marginal gross margin of a replaceable flock is less than the average gross margin of an average flock. To demonstrate the model, a broiler breeder flock from a Dutch breeder farm was used. A sensitivity analysis showed that the optimal replacement decision, for both tactical and operational management, is sensitive to the decrease in the weekly egg production after the peak and the prices of feed and hatching eggs. The effect of the decrease in weekly fertility after the peak on the replacement decision is related to the payment system for hatching eggs. PMID:23155040

  2. Feasibility of Water Cooled Thorium Breeder Reactor Based on LWR Technology

    SciTech Connect

    Takaki, Naoyuki; Permana, Sidik; Sekimoto, Hiroshi

    2007-07-01

    The feasibility of Th-{sup 233}U fueled, homogenous breeder reactor based on matured conventional LWR technology was studied. The famous demonstration at Shipping-port showed that the Th-{sup 233}U fueled, heterogeneous PWR with four different lattice fuels was possible to breed fissile but its low averaged burn-up including blanket fuel and the complicated core configuration were not suitable for economically competitive reactor. The authors investigated the wide design range in terms of fuel cell design, power density, averaged discharge burn-up, etc. to determine the potential of water-cooled Th reactor as a competitive breeder. It is found that a low moderated (MFR=0.3) H{sub 2}O-cooled reactor with comparable burn-up with current LWR is feasible to breed fissile fuel but the core size is too large to be economical because of the low pellet power density. On the other hand, D{sub 2}O-cooled reactor shows relatively wider feasible design window, therefore it is possible to design a core having better neutronic and economic performance than H{sub 2}O-cooled. Both coolant-type cores show negative void reactivity coefficient while achieving breeding capability which is a distinguished characteristics of thorium based fuel breeder reactor. (authors)

  3. Helium Leak Detection of Vessels in Fuel Transfer Cell (FTC) of Prototype Fast Breeder Reactor (PFBR)

    NASA Astrophysics Data System (ADS)

    Dutta, N. G.

    2012-11-01

    Bharatiya Nabhikiya Vidyut Nigam (BHAVINI) is engaged in construction of 500MW Prototype Fast Breeder Reactor (PFBR) at Kalpak am, Chennai. In this very important and prestigious national programme Special Product Division (SPD) of M/s Kay Bouvet Engg.pvt. ltd. (M/s KBEPL) Satara is contributing in a major way by supplying many important sub-assemblies like- Under Water trolley (UWT), Airlocks (PAL, EAL) Container and Storage Rack (CSR) Vessels in Fuel Transfer Cell (FTC) etc for PFBR. SPD of KBEPL caters to the requirements of Government departments like - Department of Atomic Energy (DAE), BARC, Defense, and Government undertakings like NPCIL, BHAVINI, BHEL etc. and other precision Heavy Engg. Industries. SPD is equipped with large size Horizontal Boring Machines, Vertical Boring Machines, Planno milling, Vertical Turret Lathe (VTL) & Radial drilling Machine, different types of welding machines etc. PFBR is 500 MWE sodium cooled pool type reactor in which energy is produced by fissions of mixed oxides of Uranium and Plutonium pellets by fast neutrons and it also breeds uranium by conversion of thorium, put along with fuel rod in the reactor. In the long run, the breeder reactor produces more fuel then it consumes. India has taken the lead to go ahead with Fast Breeder Reactor Programme to produce electricity primarily because India has large reserve of Thorium. To use Thorium as further fuel in future, thorium has to be converted in Uranium by PFBR Technology.

  4. Electromagnetic analysis of the plasma chamber of an ECR-based charge breeder

    NASA Astrophysics Data System (ADS)

    Galatà, A.; Patti, G.; Celona, L.; Mascali, D.; Neri, L.; Torrisi, G.

    2016-02-01

    The optimization of the efficiency of an ECR-based charge breeder is a twofold task: efforts must be paid to maximize the capture of the injected 1+ ions by the confined plasma and to produce high charge states to allow post-acceleration at high energies. Both tasks must be faced by studying in detail the electrons heating dynamics, influenced by the microwave-to-plasma coupling mechanism. Numerical simulations are a powerful tools for obtaining quantitative information about the wave-to-plasma interaction process: this paper presents a numerical study of the microwaves propagation and absorption inside the plasma chamber of the PHOENIX charge breeder, which the selective production of exotic species project, under construction at Legnaro National Laboratories, will adopt as charge breeder. Calculations were carried out with a commercial 3D FEM solver: first, all the resonant frequencies were determined by considering a simplified plasma chamber; then, the realistic geometry was taken into account, including a cold plasma model of increasing complexity. The results gave important information about the power absorption and losses and will allow the improvement of the plasma model to be used in a refined step of calculation reproducing the breeding process itself.

  5. Design of the low energy beam transport line between CARIBU and the EBIS charge breeder

    SciTech Connect

    Perry, A.; Ostroumov, P. N.; Barcikowski, A.; Dickerson, C.; Kondrashev, S. A.; Mustapha, B.; Savard, G.

    2015-01-09

    An Electron Beam Ion Source Charge Breeder (EBIS-CB) has been developed to breed radioactive beams from the CAlifornium Rare Isotope Breeder Upgrade (CARIBU) facility at ATLAS. The EBIS-CB will replace the existing ECR charge breeder to increase the intensity and improve the purity of reaccelerated radioactive ion beams. The EBIS-CB is in the final stage of off-line commissioning. Currently, we are developing a low energy beam transport (LEBT) system to transfer CARIBU beams to the EBIS-CB. As was originally planned, an RFQ cooler-buncher will precede the EBIS-CB. Recently, it was decided to include a multi-reflection time-of-flight (MR-TOF) mass-spectrometer following the RFQ. MR-TOF is a relatively new technology used to purify beams with a mass-resolving power up to 3×10{sup 5} as was demonstrated in experiments at CERN/ISOLDE. Very high purity singly-charged radioactive ion beams will be injected into the EBIS for charge breeding and due to its inherent properties, the EBIS-CB will maintain the purity of the charge bred beams. Possible contamination of residual gas ions will be greatly suppressed by achieving ultra-high vacuum in the EBIS trap. This paper will present and discuss the design of the LEBT and the overall integration of the EBIS-CB into ATLAS.

  6. Medical innovation laws: an unnecessary innovation.

    PubMed

    Richards, Bernadette

    2016-06-01

    Objective This paper aims to demonstrate that any suggestion that there is a need for specific innovation laws is flawed. Innovation is central to good medical practice and is adequately supported by current law. Methods The paper reviews the nature of medical innovation and outlines recent attempts in the UK to introduce specific laws aimed at 'encouraging' and 'supporting' innovation. The current legal framework is outlined and the role of the law in relation to medical innovation explored. Results The analysis demonstrates the cyclic relationship between medical advancement and the law and concludes that there is no requirement for specific innovation laws. Conclusions The law not only supports innovation and development in medical treatment but encourages it as central to a functioning medical system. There is no need to introduce specific laws aimed at medical innovation; to do so represents an unnecessary legal innovation and serves to complicate matters. What is known about the topic? Over recent months, there has been a great deal of discussion surrounding the law in the context of medical innovation. This was driven by the attempts in the UK to introduce specific laws in the Medical Innovation Bill. The general subject matter - negligence and the expected standard of care in the provision of treatment - is very well understood, but not in cases where the treatment can be described as innovative. The general rhetoric in both the UK and Australia around the Medical Innovation Bill demonstrates a lack of understanding of the position of the law with regards to innovative treatment. What does this paper add? This paper adds clarity to the debate. It presents the law and explains the manner in which the law can operate around innovative treatment. The paper asserts that medical innovation is both supported and encouraged by existing legal principles. What are the implications for practitioners? The paper presents an argument that can guide the policy position

  7. The effects of pullet body weight, dietary nonpyhtate phosphorus intake, and breeder feeding regimen on production performance, chick quality, and bone remodeling in broiler breeders.

    PubMed

    Ekmay, R D; Salas, C; England, J; Cerrate, S; Coon, C N

    2012-04-01

    A 3 × 2 × 2 factorial experiment, consisting of 52 hens per treatment, was conducted to determine the effects of pullet BW, dietary nonphytate phosphorus (NPP), and feeding regimen on performance, progeny quality, and bone remodeling. Cobb 500 broiler breeder pullets were reared to 3 different growth curves: 20% under, Cobb standard, and 20% over. Body weights were recorded weekly and feed adjustments made accordingly. At 21 wk, 624 hens were fed one of 2 breeder diets differing only in the amount of dietary NPP: 0.15 or 0.40%. A normal feeding regimen was appropriate for the particular growth curve; an alternative regimen considered the 3 growth curves together as a flock. At 24, 26, and 29 wk, blood was collected from 5 hens per treatment every 4 h over a 24-h period. Plasma samples were analyzed for total alkaline phosphatase, tartrate-resistant acid phosphatase, parathyroid hormone-related peptide, Ca, and inorganic P. Eggs per hen housed were diminished in hens fed the low dietary NPP and by low pullet target weight. Hens fed low dietary NPP also had lower egg weights but better eggshell quality. Mortality was significantly higher in hens fed low dietary NPP. Breeder tibia relative strength and ash were also significantly lower in hens fed low dietary NPP, regardless of the quantitative amount. Progeny tibia ash was not affected by any treatment. Total alkaline phosphatase responded to pullet BW, however by wk 29, total alkaline phosphatase also became sensitive to dietary NPP. The NPP by pullet BW interaction for tartrate-resistant acid phosphatase levels became significant by 29 wk, and pullet BW was significant at wk 24. The NPP by pullet growth curve interaction was also critical for plasma inorganic P levels throughout the sampling period. In summary, both 0.15% dietary NPP and reared pullets 20% under standard BW negatively affect egg production but do not impair progeny productivity. Body composition appears to be a main contributor in bone remodeling

  8. Innovation in Surgery

    PubMed Central

    Riskin, Daniel J.; Longaker, Michael T.; Gertner, Michael; Krummel, Thomas M.

    2006-01-01

    Objective: To describe the field of surgical innovation from a historical perspective, applying new findings from research in technology innovation. Background: While surgical innovation has a rich tradition, as a field of study it is embryonic. Only a handful of academic centers of surgical innovation exist, all of which have arisen within the last 5 years. To this point, the field has not been well defined, nor have future options to promote surgical innovation been thoroughly explored. It is clear that surgical innovation is fundamental to surgical progress and has significant health policy implications. A process of systematically evaluating and promoting innovation in surgery may be critical in the evolving practice of medicine. Methods: A review of the academic literature in technology innovation was undertaken. Articles and books were identified through technical, medical, and business sources. Luminaries in surgical innovation were interviewed to develop further relevance to surgical history. The concepts in technology innovation were then applied to innovation in surgery, using the historical example of surgical endoscopy as a representative area, which encompasses millennia of learning and spans multiple specialties of care. Results: The history of surgery is comprised largely of individual, widely respected surgeon innovators. While respecting individual accomplishments, surgeons as a group have at times hindered critical innovation to the detriment of our profession and patients. As a clinical discipline, surgery relies on a tradition of research and attracting the brightest young minds. Innovation in surgery to date has been impressive, but inconsistently supported. Conclusion: A body of knowledge on technology innovation has been developed over the last decade but has largely not been applied to surgery. New surgical innovation centers are working to define the field and identify critical aspects of surgical innovation promotion. It is our

  9. Preliminary study on nano- and micro-composite sol-gel based alumina coatings on structural components of lead-bismuth eutectic cooled fast breeder reactors

    NASA Astrophysics Data System (ADS)

    Dou, Peng; Kasada, Ryuta

    2011-02-01

    In order to protect the structural components of lead-bismuth eutectic cooled fast breeder reactors from liquid metal corrosion, Al 2O 3 nano- and micro-composite coatings were developed using an improved sol-gel process, which includes dipping specimens in a sol-gel solution dispersed with fine α-Al 2O 3 powders prepared by mechanical milling. Accelerated corrosion tests were conducted on coated specimens in liquid lead-bismuth eutectic at 500 °C under dynamic conditions. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) analyses revealed that the coatings are composed of α-Al 2O 3 and they are about 10 μm thick. After the corrosion tests, no spallation occurred on the coatings, and neither Pb nor Bi penetrated into the coatings, which indicates that the coatings possess an enhanced dynamic LBE corrosion resistance to lead-bismuth eutectic corrosion. The nano-structured composite particles integrated into the coatings play an important role in achieving such superior lead-bismuth eutectic corrosion resistance.

  10. The effect of low-density broiler breeder diets on performance and immune status of their offspring.

    PubMed

    Enting, H; Boersma, W J A; Cornelissen, J B W J; van Winden, S C L; Verstegen, M W A; van der Aar, P J

    2007-02-01

    Effects of low-density broiler breeder diets on offspring performance and mortality were studied using 2,100 female and 210 male Cobb 500 breeders. Breeder treatments involved 4 experimental groups and a control group with normal density diets (ND, 2,600 kcal of AME/kg during rearing and 2,800 kcal of AME/kg during laying). In treatment 2, nutrient densities were decreased by 12% (LD12) and 11% (LD11) during the rearing and laying periods, respectively, whereas in treatment 3, nutrient densities were decreased by 23% (LD23) and 21% (LD21) during the rearing and laying periods, respectively. The nutrient density in these treatments was decreased through inclusion of palm kernel meal, wheat bran, wheat gluten feed, and sunflower seed meal in the diets. Treatment 4 included diets with the same nutrient densities as in treatment 2 but included oats and sugar beet pulp (LD12(OP) and LD11(OP)). In treatment 5, the same low-density diet was given to the breeders as in treatment 2 during the rearing period, but it was followed by a normal density diet during the laying period (LD12-ND). Treatments were applied from 4 to 60 wk of age. On low-density diets, offspring showed an increased 1-d-old weight. As compared with offspring of breeders that received ND, the d 38 live weight of chickens from 29-wk-old breeders fed LD11 was improved. Mortality was reduced in offspring from 60-wk-old parent stock given low-density diets. The IgM titers in 35-d-old offspring from eggs with a lower-than-average weight were reduced when 29-wk-old broiler breeders were fed low-density diets. In offspring from eggs with a higher-than-average weight from 60-wk-old parent stock given LD11 or LD21 diets, IgM titers were higher compared with ND. It was concluded that low-density broiler breeder diets can improve offspring growth rates, reduce mortality, and reduce or increase immune responses, depending on breeder age and egg weight. PMID:17234841

  11. Effect of sex ratios, spiking and extra artificial insemination on the breeding efficiency of broiler breeders.

    PubMed

    Végi, Barbara; Váradi, Eva; Szőke, Zsuzsanna; Barna, Judit

    2013-09-01

    Since early fertility decline is a permanent problem of broiler breeders, the aim of this study was to test the effects of various sex ratios, spiking strategies and additional artificial inseminations (AI) on their breeding efficiency. Six breeder flocks were analysed during the whole reproduction cycle. In Flock A the sex ratio was maintained at 10% during the whole cycle (control), while in Flock B the number of males was increased to a final ratio of 16%. In Flocks C (technological control), D, E and F the ratio of males was gradually decreased from 10% to 6.5% until the end of the cycle. Moreover, at the age of 44 weeks in Flocks D and E 50 and 100% of cockerels were replaced by young ones, respectively, while in Flock F additional artificial inseminations were applied in the second half of the reproduction cycle. The increase of sperm transport was successful only in Groups B (increase in male numbers) and D (50% replacement of old cockerels with young ones); however, it was not sufficient for increasing the fertility rates in either group. Nor did additional artificial inseminations (Flock F) have an effect on fertility. As a conclusion, it can be established that increasing the sperm count in the hens' oviducts in any way could not improve fertility in the last third of the production cycle. The results also suggest that the expensive and labour-intensive spiking technique used in broiler breeder management is useless. The prime factor responsible for the shortened persistence of fertility may be the reduced ability of the female oviduct to accept and store sperm. PMID:23921351

  12. Investigation of ion capture in an electron beam ion trap charge-breeder for rare isotopes

    NASA Astrophysics Data System (ADS)

    Kittimanapun, Kritsada

    Charge breeding of rare isotope ions has become an important ingredient for providing reaccelerated rare isotope beams for science. At the National Superconducting Cyclotron Laboratory (NSCL), a reaccelerator, ReA, has been built that employs an advanced Electron Beam Ion Trap (EBIT) as a charge breeder. ReA will provide rare-isotope beams with energies of a few hundred keV/u up to tens of MeV/u to enable the study of properties of rare isotopes via low energy Coulomb excitation and transfer reactions, and to investigate nuclear reactions important for nuclear astrophysics. ReA consists of an EBIT charge breeder, a charge-over-mass selector, a room temperature radio-frequency quadrupole accelerator, and a superconducting radio-frequency linear accelerator. The EBIT charge breeder features a high-current electron gun, a long trap structure, and a hybrid superconducting magnet to reach both high acceptance for injected low-charge ions as well as high-electron beam current densities for fast charge breeding. In this work, continuous ion injection and capture in the EBIT have been investigated with a dedicated Monte-Carlo simulation code and in experimental studies. The Monte-Carlo code NEBIT considers the electron-impact ionization cross sections, space charge due to the electron beam current, ion dynamics, electric field from electrodes, and magnetic field from the superconducting magnet. Experiments were performed to study the capture efficiency as a function of injected ion beam current, electron beam current, trap size, and trap potential depth. The charge state evolution of trapped ions was studied, providing information about the effective current density of the electron beam inside the EBIT. An attempt was made to measure the effective space-charge potential of the electron beam by studying the dynamics of a beam injected and reflected inside the trap.

  13. Identification of novel candidate genes for follicle selection in the broiler breeder ovary

    PubMed Central

    2012-01-01

    Background Broiler breeders fed ad libitum are characterised by multiple ovulation, which leads to poor shell quality and egg production. Multiple ovulation is controlled by food restriction in commercial flocks. However, the level of food restriction raises welfare concerns, including that of severe hunger. Reducing the rate of multiple ovulation by genetic selection would facilitate progress towards developing a growth profile for optimum animal welfare. Results The study utilised 3 models of ovarian follicle development; laying hens fed ad libitum (experiment 2) and broiler breeders fed ad libitum or a restricted diet (experiments 1 & 3). This allowed us to investigate gene candidates for follicular development by comparing normal, abnormal and “controlled” follicle hierarchies at different stages of development. Several candidate genes for multiple ovulation were identified by combining microarray analysis of restricted vs. ad libitum feeding, literature searches and QPCR expression profiling throughout follicle development. Three candidate genes were confirmed by QPCR as showing significant differential expression between restricted and ad libitum feeding: FSHR, GDF9 and PDGFRL. PDGFRL, a candidate for steroidogenesis, showed significantly up-regulated expression in 6–8 mm follicles of ad libitum fed broiler breeders (P = 0.016), the period at which follicle recruitment occurs. Conclusions Gene candidates have been identified and evidence provided to support a possible role in regulation of ovarian function and follicle number. Further characterisation of these genes will be required to assess their potential for inclusion into breeding programmes to improve the regulation of follicle selection and reduce the need for feed restriction. PMID:22992265

  14. High performance charge breeder for HIE-ISOLDE and TSR@ISOLDE applications

    SciTech Connect

    Shornikov, Andrey Mertzig, Robert C.; Wenander, Fredrik J. C.; Beebe, Edward N.; Pikin, Alexander

    2015-01-09

    We report on the development of the HEC{sup 2} (High Energy Compression and Current) charge breeder, a possible high performance successor to REXEBIS at ISOLDE. The new breeder would match the performance of the HIE-ISOLDE linac upgrade and make full use of the possible installation of a storage ring at ISOLDE (the TSR@ISOLDE initiative [1]). Dictated by ion beam acceptance and capacity requirements, the breeder features a 2–3.5 A electron beam. In many cases very high charge states, including bare ions up to Z=70 and Li/Na-like up to Z=92 could be requested for experiments in the storage ring, therefore, electron beam energies up to 150 keV are required. The electron-beam current density needed for producing ions with such high charge states at an injection rate into TSR of 0.5–1 Hz is between 10 and 20 kA/cm{sup 2}, which agrees with the current density needed to produce A/q<4.5 ions for the HIE-ISOLDE linac with a maximum repetition rate of 100 Hz. The first operation of a prototype electron gun with a pulsed electron beam of 1.5 A and 30 keV was demonstrated in a joint experiment with BNL [2]. In addition, we report on further development aiming to achieve CW operation of an electron beam having a geometrical transverse ion-acceptance matching the injection of 1{sup +} ions (11.5 μm), and an emittance/energy spread of the extracted ion beam matching the downstream mass separator and RFQ (0.08 μm normalized / ± 1%)

  15. [A beautiful cow is a good cow. Dutch scientists and commercial breeders on cattle breeding, 1900-1950].

    PubMed

    Theunissen, Bert

    2008-01-01

    In the agricultural journal De Nieuwe Veldbode of 1941 Dutch scientists, agricultural engineers, commercial cattle breeders and herd-book officials engaged in a prolonged debate about cattle breeding methods. Geneticist Arend Hagedoorn started the debate by accusing commercial breeders of deceiving their buyers. In his view, breeders were merely interested in producing beautiful show bulls that could be sold for high prices, and they ignored the animals' hereditary potential for milk production. Rational breeding, he argued, required progeny testing: only the production of his daughters should decide on a bull's merits. Commercial breeders denied the charge. They did indeed select for conformation, not however for aesthetic reasons, but to safeguard the health and durability of the breed. In their view, selecting for production was not feasible in practice and would, moreover, lead to the degeneration of the breed. In this article I explore the backgrounds of this debate by investigating the different views of scientists and practical breeders on theory and practice of cattle breeding in the first half of the century. I shall show that to understand the different viewpoints, the practical realities of dairy farming under Dutch circumstances, commercial considerations and normative ideas on good farming have to be taken into account. PMID:22586751

  16. Vitamin E and selenium in broiler breeder diets: Effect on live performance, hatching process, and chick quality.

    PubMed

    Urso, U R A; Dahlke, F; Maiorka, A; Bueno, I J M; Schneider, A F; Surek, D; Rocha, C

    2015-05-01

    This study evaluated the effect of different dietary vitamin E levels and different selenium sources on the productive and reproductive performance of broiler breeders. In total 640 females and 64 males between 22 and 52 weeks old were studied. A completely randomized experimental design in factorial arrangement, with 4 treatments of 8 replicates with 20 females and 2 males each, was applied. Treatments consisted of 2 vitamin E levels (30 and 120 mg/kg) and two selenium sources (sodium selenite and zinc-L-selenomethionine). Egg production (rate of lay and eggs per breeder), egg characteristics (egg, yolk, eggshell, and albumen weights), fertility, incubation responses (egg weight loss during incubation, hatchability, and hatching window), and hatchling characteristics (weight and yield) were evaluated. There was no influence of dietary vitamin E levels or selenium sources on egg production (P > 0.05). Mature breeders (47 weeks old) fed zinc-L-selenomethionine and 120 mg vitamin E/kg feed produced heavier eggs and albumen. Hatchability of the eggs of breeders fed 120 mg vitamin E/kg feed was higher than breeders fed 30 mg vitamin at 29 wks. The dietary inclusion of organic selenium also promoted heavier hatchling weight until egg production peak (33 wk), but did not influence hatchling quality or hatching window. It was concluded that the dietary supplementation of zinc-L-selenomethione and vitamin E (120 mg/kg feed) could be used to improve egg characteristics and incubation response. PMID:25713394

  17. Innovating a way out

    NASA Astrophysics Data System (ADS)

    2015-09-01

    The ongoing European Union fiscal crisis has taken its toll on research and innovation across several member states. A number of initiatives aim to boost technological innovation as a tool for increasing wealth.

  18. Innovation and STEM Schools

    ERIC Educational Resources Information Center

    Roberts, Julia Link

    2015-01-01

    How do schools with a focus on science, technology, engineering, and mathematics (STEM) fit in with state goals to increase innovation and to boost the economy? This article briefly discusses how educators can encourage creativity and innovation.

  19. Detection and characterization of chicken anemia virus from commercial broiler breeder chickens

    PubMed Central

    Hailemariam, Zerihun; Omar, Abdul Rahman; Hair-Bejo, Mohd; Giap, Tan Ching

    2008-01-01

    Background Chicken anemia virus (CAV) is the causative agent of chicken infectious anemia (CIA). Study on the type of CAV isolates present and their genetic diversity, transmission to their progeny and level of protection afforded in the breeder farms is lacking in Malaysia. Hence, the present study was aimed to detect CAV from commercial broiler breeder farms and characterize CAV positive samples based on sequence and phylogenetic analysis of partial VP1 gene. Results A total of 12 CAV isolates from different commercial broiler breeder farms were isolated and characterized. Detection of CAV positive embryos by the PCR assay in the range of 40 to 100% for different farms indicated high level of occurrence of vertical transmission of viral DNA to the progeny. CAV antigen was detected in the thymus and in the bone marrow but not in spleen, liver, duodenum, ovary and oviduct by indirect immunoperoxidase staining. The 12 CAV isolates were characterized based on partial sequences of VP1 gene. Six isolates (MF1A, MF3C, M3B5, NF4A, P12B and P24A) were found to have maximum homology with previously characterized Malaysian isolate SMSC-1, four isolates (M1B1, NF3A, PYT4 and PPW4) with isolate BL-5 and the remaining two (NF1D and NF2C) have maximum homology both with isolates 3-1 and BL-5. Meanwhile, seven of the isolates with amino acid profile of 75-I, 97-L, 139-Q and 144-Q were clustered together in cluster I together with other isolates from different geographical places. The remaining five isolates with amino acid profile of 75-V, 97-M, 139-K and 144-E were grouped under cluster II. All the CAV isolates demonstrated omega values (Ka/Ks) of less than one (the values ranging from 0.07 to 0.5) suggesting the occurrence of purifying (negative) selection in all the studied isolates. Conclusion The present study showed that CAV is widespread in the studied commercial broiler breeder farms. The result also indicated the occurrence of genetic variability in local CAV isolates

  20. Method of locating a leaking fuel element in a fast breeder power reactor

    DOEpatents

    Honekamp, John R.; Fryer, Richard M.

    1978-01-01

    Leaking fuel elements in a fast reactor are identified by measuring the ratio of .sup.134 Xe to .sup.133 Xe in the reactor cover gas following detection of a fuel element leak, this ratio being indicative of the power and burnup of the failed fuel element. This procedure can be used to identify leaking fuel elements in a power breeder reactor while continuing operation of the reactor since the ratio measured is that of the gases stored in the plenum of the failed fuel element. Thus, use of a cleanup system for the cover gas makes it possible to identify sequentially a multiplicity of leaking fuel elements without shutting the reactor down.

  1. Comparative study of the effects of organic selenium on hen performance and productivity of broiler breeders.

    PubMed

    Rajashree, K; Muthukumar, T; Karthikeyan, N

    2014-01-01

    1. A 10-week experiment was conducted with Ross 308 broiler breeder chickens in cages to evaluate the influence of organic and inorganic sources of selenium (Se) supplementation. A total of 600 birds at 29 weeks of age were divided at random into 4 groups and fed on a maize-soya basal diet supplemented with different forms of Se. 2. The first (control) group was given the basal diet without Se supplementation, whereas the second, third and fourth groups were given, respectively, the basal diet with 0.3 mg/kg of inorganic Se in the form of sodium selenite or 0.3 and 0.5 mg/kg of organic Se in the form of Se enriched yeast (Se-yeast). 3. The experiment was carried out for 10 weeks to compare and evaluate the influence of Se supplementation on breeder performance, egg production, hatchability and the quality of eggs. Samples were collected for analysis at weeks 0, 5 and 10 of the experimental period. 4. At the end of the experiment (39 weeks), there was a reduction in mortality in breeders given diets supplemented with 0.5 mg/kg of Se-yeast. Supplementation of feed with 0.5 mg/kg organic Se increased egg production, percentage of settable eggs and hatchability. 5. Selenium supplementation increased egg weight and specific gravity compared to the control diet. However, no significant variation was found in albumen or yolk protein content at the end of week 10. 6. Selenium accumulation and glutathione peroxidase (GSHPx) activity were lower in the egg albumen and yolk of control compared with Se-supplemented treatments. Se accumulation and GSHPx activity were higher in the group given 0.3 mg/kg organic compared to 0.3 mg/kg of inorganic Se. 7. The results favour the use of Se-yeast at the dose of 0.5 mg/kg in broiler breeder diets for better productivity of eggs, settable eggs, hatchability and higher Se accumulation and antioxidant status in eggs. PMID:24814053

  2. Role of the serotonergic axis in the reproductive failure associated with aging broiler breeder roosters.

    PubMed

    Avital-Cohen, N; Heiblum, R; Rosenstrauch, A; Chaiseha, Y; Mobarkey, N; Gumułka, M; Rozenboim, I

    2015-10-01

    Reproductive failure associated with aging is a well-known phenomenon. However, the mechanism by which this failure occurs in broiler breeder roosters is still unclear. A previous study conducted in our laboratory, comparing young and aging broiler breeder roosters, demonstrated an elevation in hypothalamic vasoactive intestinal peptide (VIP) and pituitary prolactin (PRL) gene expression accompanied by a deterioration of gonadal axis function. This resulted in a decrease in semen-quality variables as roosters aged. The objective of this study was to examine the involvement of the serotonergic axis in the age-associated reproductive failure in broiler breeder roosters. Cobb roosters aged 64 wk were divided into 3 groups (n = 20 each): parachlorophenylalanine (PCPA) administration, active immunization against chicken VIP, and controls. At 69 wk of age, each group was divided into 2 equal subgroups: 1 received ovine PRL and the other served as controls. Weekly semen volume, concentration and motility, and plasma testosterone, estradiol, and PRL concentrations were examined. At the end of the experiment, roosters were euthanized, testes were weighed, and hypothalamus and pituitary were removed to assay the expression of genes encoding hypothalamic GnRH-I, pituitary FSH, pituitary LH, hypothalamic VIP, and pituitary PRL. Both PCPA administration and active immunization against chicken VIP significantly increased testis weight, semen volume, sperm concentration, ejaculation grade, plasma testosterone level, and GnRH-I, FSH and LH gene expression compared with controls (P ≤ 0.05). In addition, a decrease in plasma estradiol and PRL concentrations and VIP and PRL gene expression was observed in PCPA- and VIP-immunized birds compared with controls (P ≤ 0.05). Administration of PRL in all groups decreased gonadal axis function and semen-quality variables (P ≤ 0.05). Collectively, these results suggest that the increasing expression levels of the serotonergic axis

  3. Scram reliability under seismic conditions at the Experimental Breeder Reactor II

    SciTech Connect

    Roglans, J.; Wang, C.Y.; Hill, D.J.

    1993-08-01

    A Probabilistic Risk Assessment of the Experimental Breeder Reactor II has recently been completed. Seismic events are among the external initiating events included in the assessment. As part of the seismic PRA a detailed study has been performed of the ability to shutdown the reactor under seismic conditions. A comprehensive finite element model of the EBR-II control rod drive system has been used to analyze the control rod system response when subjected to input seismic accelerators. The results indicate the control rod drive system has a high seismic capacity. The estimated seismic fragility for the overall reactor shutdown system is dominated by the primary tank failure.

  4. The UF6 Breeder - A solution to the problems of nuclear power

    NASA Technical Reports Server (NTRS)

    Williams, J. R.; Clement, J. D.; Rust, J. A.

    1975-01-01

    One of the major advantages of uranium hexafluoride reactors for power generation is the simplified fuel reprocessing scheme which the gaseous fuel makes possible. Critical experiments related to the development of the reactors for electric power generation are discussed along with UF6 breeder reactor studies. Previous energy conversion studies are reported, taking into account gas turbine power plants, thermionic conversion, and MHD conversion. Thermodynamic cycle analyses show that high efficiencies can be achieved using UF6 as the working fluid for Rankine or Brayton cycles without requiring excessive temperatures.

  5. Effect of Dietary Vitamin A on Reproductive Performance and Immune Response of Broiler Breeders

    PubMed Central

    Guo, Yuming; Wang, Yongwei; Guo, Shuangshuang

    2014-01-01

    The effects of dietary vitamin A supplementation on reproductive performance, liver function, fat-soluble vitamin retention, and immune response were studied in laying broiler breeders. In the first phase of the experiment, 1,120 Ross-308 broiler breeder hens were fed a diet of corn and soybean meal supplemented with 5,000 to 35,000 IU/kg vitamin A (retinyl acetate) for 20 weeks. In the second phase, 384 Ross-308 broiler breeder hens were fed the same diet supplemented with 5,000 to 135,000 IU/kg vitamin A (retinyl acetate) for 24 weeks. The hens' reproductive performance, the concentrations of vitamins A and E in liver and egg yolk, liver function, mRNA expression of vitamin D receptor in duodenal mucosa, antibody titers against Newcastle disease virus vaccine, and T-cell proliferation responses were evaluated. Supplementation of vitamin A at levels up to and including 35,000 IU/kg did not affect reproductive performance and quadratically affected antibody titer to Newcastle disease virus vaccine (p<0.05). Dietary addition of vitamin A linearly increased vitamin A concentration in liver and yolk and linearly decreased α-, γ-, and total tocopherol concentration in yolk (p<0.01) and α-tocopherol in liver (p<0.05). Supplementation of vitamin A at doses of 45,000 IU/kg and above significantly decreased egg weight, yolk color, eggshell thickness and strength, and reproductive performance. Dietary vitamin A significantly increased mRNA expression of vitamin D receptor in duodenal mucosa (p<0.05), increased aspartate amino transferase activity, and decreased total bilirubin concentration in serum. Supplementation of vitamin A at 135,000 IU/kg decreased the proliferation of peripheral blood lymphocytes (p<0.05). Therefore, the maximum tolerable dose of vitamin A for broiler breeders appears to be 35,000 IU/kg, as excessive supplementation has been shown to impair liver function, reproductive performance, and immune response. PMID:25148198

  6. The Impact of Innovation

    ERIC Educational Resources Information Center

    O'Banion, Terry; Weidner, Laura; Wilson, Cynthia

    2012-01-01

    With funding from MetLife Foundation, the League for Innovation in the Community College engaged in a yearlong study in 2009 of the nature of innovation in the community college. Using recipients of the League's Innovation of the Year Award at 19 community colleges during the period from 1999 through 2008 as a data set, the authors used document…

  7. China's Innovation Paradox

    ERIC Educational Resources Information Center

    Chan, Jeremy

    2015-01-01

    China aims to become an innovation-led nation by 2020, but its leadership is generally sceptical--and oftentimes hostile--to the market forces, open exchange of ideas, and creative destruction that have unlocked innovation in other countries. Instead, Beijing hopes to promote innovation in China through a massive expansion in higher education,…

  8. Effects of dietary canthaxanthin and 25-hydroxycholecalciferol supplementation on the antioxidant status and tibia quality of duck breeders and newly hatched ducklings.

    PubMed

    Ren, Z Z; Jiang, S Z; Zeng, Q F; Ding, X M; Bai, S P; Wang, J P; Luo, Y H; Su, Z W; Xuan, Y; Zhang, K Y

    2016-09-01

    This study evaluated the effects of dietary canthaxanthin (CX) and 25-hydroxycholecalciferol (25-OH-D3) supplementation on the antioxidant status and tibia quality of duck breeders and newly hatched ducklings. In total, 780 female and 156 male duck breeders were randomly allotted to 2 treatments. Duck breeders were fed either a commercial diet (containing 3,000 IU/kg vitamin D3) or the same diet plus a mixture of CX (6 mg/kg) and 25-OH-D3 (0.069 mg/kg) for 40 wk. The antioxidant status of duck breeders, egg yolk, and ducklings; tibia quality of duck breeders and ducklings; and shell quality of breeder eggs were investigated. The total antioxidant capacity of breeder female liver (P = 0.028), breeder male testis (P = 0.049), egg yolk (P = 0.032), one-day-old duckling liver (P = 0.024), and one-day-old duckling yolk sac (P = 0.012) were increased by dietary supplementation of the mixture of CX and 25-OH-D3 The inclusion of CX and 25-OH-D3 decreased liver protein carbonyl of breeder females (P = 0.030), and liver malonaldehyde (P = 0.050) and protein carbonyl (P = 0.030) of breeder males. Yolk (P < 0.001), shank (P < 0.001), and yolk sac pigmentation (P < 0.001) of one-day-old ducklings were increased by the supplementation of the CX and 25-OH-D3 mixture. No differences (P > 0.05) were observed in tibia quality or eggshell quality between treatments. In conclusion, the inclusion of the mixture of CX and 25-OH-D3 in a diet sufficient in vitamin D3 increased antioxidant status but not tibia quality of duck breeders and newly hatched ducklings. PMID:26994193

  9. Molecular Characterization of Motile Serovars of Salmonella enterica from Breeder and Commercial Broiler Poultry Farms in Bangladesh

    PubMed Central

    Barua, Himel; Biswas, Paritosh K.; Olsen, Katharina E. P.; Shil, Subrata K.; Christensen, Jens P.

    2013-01-01

    Contaminated poultry and poultry products are a major source of motile Salmonellae for human salmonellosis worldwide. Local circulation of any motile Salmonella serovar in poultry has a wider public health impact beyond its source of origin for being dispersed elsewhere through poultry trades or human travels. To investigate the status of motile Salmonella serovars in breeder farms in Bangladesh, multiple flocks of two breeder farms were observed for a period of six months. In addition, a cross-sectional survey was carried out to determine the prevalence and serovar distribution of motile Salmonella by randomly selecting 100 commercial broiler poultry farms. Five pooled faecal samples representing an entire housed flock of breeders or broilers were screened for presence of motile Salmonella following conventional bacteriological procedures. The Salmonella isolates obtained were subsequently serotyped, and characterized by plasmid profiling and pulsed-field gel electrophoresis (PFGE). The results revealed that both the breeder farms were positive with three Salmonella serovars: S. Virchow, S. Paratyphi B var Java (S. Java) and S. Enteritidis. Eleven of the 100 broiler farms investigated were positive for motile Salmonella, giving a farm-level prevalence of 11% (95% confidence interval 5–17%). S. Virchow and S. Kentucky were the two predominant serovars isolated from the broiler farms. The PFGE genotyping demonstrated that the isolates belonging to the same serovars were closely related due to variation in only 1–4 bands. All the S. Virchow and S. Java isolates, irrespective of breeder or broiler farm origin, were plasmid-free, except for one S. Virchow isolate from a broiler farm that harboured a 9.7 kb-sized plasmid. The S. Kentucky isolates belonged to three plasmid profiles having plasmids of four different sizes, ranging from 2.7 to 109 kb. This is the first report of any motile Salmonella serovars from breeder and commercial broiler poultry farms in

  10. Effects of dietary supplementation of meat-type quail breeders with guanidinoacetic acid on their reproductive parameters and progeny performance.

    PubMed

    Murakami, A E; Rodrigueiro, R J B; Santos, T C; Ospina-Rojas, I C; Rademacher, M

    2014-09-01

    This study was conducted to assess the effect of dietary supplementation of meat-type quail breeders with guanidinoacetic acid (GAA) on their reproductive parameters and progeny performance. Two hundred forty meat-type quails at 25 wk of age were distributed in a completely randomized design with 5 treatments and 8 replicates of 6 birds each. The treatments consisted of 5 dietary levels of GAA (0.00, 0.06, 0.12, 0.18, and 0.24%). The progenies from quail breeders were housed according to breeder treatments and fed a conventional diet based on corn and soybean meal without GAA supplementation. Dietary GAA levels did not affect (P > 0.05) the productivity of meat-type quail breeders, although the concentration of guanidinic compounds (creatine, GAA, and creatinine) in the eggs from the breeders increased linearly (P < 0.05) according to the increase in dietary GAA levels. The number of spermatozoa present in the vitelline membrane was not affected (P > 0.05) by the treatments, but there was a quadratic effect (P < 0.05) of the levels of GAA on fertility, embryonic mortality, and egg hatchability, with the best results estimated at 0.13, 0.15, and 0.14% GAA, respectively. The creatine levels of the pectoral muscle in newborn quails showed a quadratic effect (P ≤ 0.07), and the dietary GAA level of 0.11% was estimated to maximize the muscular creatine level in the progeny. There was a quadratic effect (P < 0.05) of GAA levels on weight gain and feed conversion of progeny at 35 d of age with an optimization point of 0.14% GAA for these variables. Dietary GAA supplementation of meat-type quail breeders increases the availability of creatine in eggs and muscle of progeny, which results in better reproductive parameters and better postnatal progeny performance. PMID:24974392