Science.gov

Sample records for laboratory hetch hetchy

  1. Arroyo Mocho Boulder Removal Project: Lawrence Livermore National Laboratory Hetch Hetchy Pump Station

    SciTech Connect

    Burkholder, L; Kato, T; Van Hattem, M

    2007-06-28

    The purpose of this biological assessment is to review the proposed Arroyo Mocho Boulder Removal Project in sufficient detail to determine to what extent the proposed action may affect any of the threatened, endangered, proposed, or sensitive species and designated or proposed critical habitats listed below. In addition, the following information is provided to comply with statutory requirements to use the best scientific and commercial information available when assessing the risks posed to listed and/or proposed species and designated and/or proposed critical habitat by proposed federal actions. This biological assessment is prepared in accordance with legal requirements set forth under regulations implementing Section 7 of the Endangered Species Act (50 CFR 402; 16 U.S.C 1536 (c)). It is our desire for the Arroyo Mocho Boulder Removal Project to receive incidental take coverage for listed species and critical habitat within the greater project area by means of amending the previous formal Section 7 consultation (1-1-04-F-0086) conducted a few hundred meters downstream by Lawrence Livermore National Laboratory (LLNL) in 2002. All conservation measures, terms and conditions, and reporting requirements from the previous Biological Opinion (1-1-04-F-0086) have been adopted for this Biological Assessment and/or amendment.

  2. 33 CFR 208.82 - Hetch Hetchy, Cherry Valley, and Don Pedro Dams and Reservoirs.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 33 Navigation and Navigable Waters 3 2012-07-01 2012-07-01 false Hetch Hetchy, Cherry Valley, and Don Pedro Dams and Reservoirs. 208.82 Section 208.82 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE FLOOD CONTROL REGULATIONS § 208.82 Hetch Hetchy, Cherry Valley, and Don Pedro Dams and...

  3. 33 CFR 208.82 - Hetch Hetchy, Cherry Valley, and Don Pedro Dams and Reservoirs.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 33 Navigation and Navigable Waters 3 2013-07-01 2013-07-01 false Hetch Hetchy, Cherry Valley, and Don Pedro Dams and Reservoirs. 208.82 Section 208.82 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE FLOOD CONTROL REGULATIONS § 208.82 Hetch Hetchy, Cherry Valley, and Don Pedro Dams and...

  4. 33 CFR 208.82 - Hetch Hetchy, Cherry Valley, and Don Pedro Dams and Reservoirs.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 33 Navigation and Navigable Waters 3 2014-07-01 2014-07-01 false Hetch Hetchy, Cherry Valley, and..., Cherry Valley, and Don Pedro Dams and Reservoirs. The Turlock Irrigation District and Modesto Irrigation..., shall operate Hetch Hetchy Dam and Reservoir and Cherry Valley Dam and Reservoir in the interest...

  5. 33 CFR 208.82 - Hetch Hetchy, Cherry Valley, and Don Pedro Dams and Reservoirs.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 33 Navigation and Navigable Waters 3 2011-07-01 2011-07-01 false Hetch Hetchy, Cherry Valley, and..., Cherry Valley, and Don Pedro Dams and Reservoirs. The Turlock Irrigation District and Modesto Irrigation..., shall operate Hetch Hetchy Dam and Reservoir and Cherry Valley Dam and Reservoir in the interest...

  6. Impacts of Regulated Flow on the Tuolumne River below Hetch Hetchy Reservoir and Potential Mitigation Measures, Yosemite National Park, CA

    NASA Astrophysics Data System (ADS)

    Roche, J. W.; Stock, G. M.; Buhler, M. S.

    2008-12-01

    Following the completion of O'Shaughnessy Dam in 1923 and the inundation of Hetch Hetchy Valley, the San Francisco Public Utilities Commission has regulated flows downstream of the dam for water supply and electricity production purposes. This study examines the conditions along the 10 kilometers of the Tuolumne River below the dam within Yosemite National Park with the objective of managing future flows for ecological benefit. In particular, we focus on a 26.4 hectare riparian wetland complex called Poopenaut Valley that is particularly sensitive to managed flow conditions. The primary impacts of flow alteration are reduced meadow inundation frequency (10-25%) and a greater concomitant reduction in shallow soil saturation duration necessary to support wetlands and meadow habitats. Asynchronous spring runoff peaks from tributaries crossing the meadow, coupled with rapid stage changes on the main stem Tuolumne River from managed flows, may have led to incision of tributary channels. Groundwater elevations throughout the meadow are generally greater than 3 meters below ground surface for much of the year and only approach elevations within 0.5 meters of the ground surface, that level useful to wetland plants, during floods on the Tuolumne River. An experimental flood of 177 cms (6,250 cfs) on May 26-27, 2008 revealed flood levels necessary to achieve substantial inundation of low lying meadow areas as well as a seasonal off-channel pond. Subsequent moderate flows revealed considerable heterogeneity in meadow soil transmissivity and hence response times to floods of a given magnitude. By combining this information with meadow and wetland vegetation distributions and characteristics, we intend to identify river flow magnitudes, timing, durations, and frequencies necessary to sustain or improve current meadow conditions in Poopenaut Valley.

  7. 33 CFR 208.82 - Hetch Hetchy, Cherry Valley, and Don Pedro Dams and Reservoirs.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Don Pedro Dams and Reservoirs. 208.82 Section 208.82 Navigation and Navigable Waters CORPS OF..., Cherry Valley, and Don Pedro Dams and Reservoirs. The Turlock Irrigation District and Modesto Irrigation District, acting jointly, hereinafter called the Districts, shall operate Don Pedro Dam and Reservoir...

  8. Beyond Knee-Jerk Environmental Thinking: Teaching Geographic Perspectives on Conservation, Preservation and the Hetch Hetchy Valley Controversy

    ERIC Educational Resources Information Center

    Moseley, William G.

    2009-01-01

    Attention to scale, use of space and connections between places and regions are general, yet distinctive, geographical concepts that may be employed in introductory level human-environment geography courses to distinguish them from other environmental studies offerings. This article demonstrates how attention to the aforementioned concepts…

  9. 27 CFR 9.46 - Livermore Valley.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... of section 14 to its intersection with the Hetch Hetchy Aqueduct, T4S, R2E; then (15) Follow the Hetch Hetchy Aqueduct west-southwest approximately 4.2 miles to the Aqueduct's intersection with the...

  10. Benchmarking Heavy Ion Transport Codes FLUKA, HETC-HEDS MARS15, MCNPX, and PHITS

    SciTech Connect

    Ronningen, Reginald Martin; Remec, Igor; Heilbronn, Lawrence H.

    2013-06-07

    Powerful accelerators such as spallation neutron sources, muon-collider/neutrino facilities, and rare isotope beam facilities must be designed with the consideration that they handle the beam power reliably and safely, and they must be optimized to yield maximum performance relative to their design requirements. The simulation codes used for design purposes must produce reliable results. If not, component and facility designs can become costly, have limited lifetime and usefulness, and could even be unsafe. The objective of this proposal is to assess the performance of the currently available codes PHITS, FLUKA, MARS15, MCNPX, and HETC-HEDS that could be used for design simulations involving heavy ion transport. We plan to access their performance by performing simulations and comparing results against experimental data of benchmark quality. Quantitative knowledge of the biases and the uncertainties of the simulations is essential as this potentially impacts the safe, reliable and cost effective design of any future radioactive ion beam facility. Further benchmarking of heavy-ion transport codes was one of the actions recommended in the Report of the 2003 RIA R&D Workshop".

  11. Benchmarking of calculated projectile fragmentation cross-sections using the 3-D, MC codes PHITS, FLUKA, HETC-HEDS, MCNPX_HI, and NUCFRG2

    NASA Astrophysics Data System (ADS)

    Sihver, L.; Mancusi, D.; Niita, K.; Sato, T.; Townsend, L.; Farmer, C.; Pinsky, L.; Ferrari, A.; Cerutti, F.; Gomes, I.

    several particle and heavy-ion MC transport codes exist, e.g. Particle and Heavy-Ion Transport code System (PHITS), High Energy Transport Code-Human Exploration and Development of Space (HETC-HEDS), SHIELD-HIT, GEANT4, FLUKA, MARS, and MCNPX. In this paper, we present an extensive benchmarking of the calculated projectile fragmentation cross-sections from the reactions of 300-1000MeV/u28Si, 40Ar, and 56Fe on polyethylene, carbon, aluminum, and copper targets (relevant to space radioprotection) using PHITS, FLUKA, HETC-HEDS, and MCNPX, against measurements. The influence of the different models used in the different transport codes on the calculated results is also discussed. Some measured cross-sections are also compared to the calculated cross-sections using NUCFRG2, which are incorporated in the 1-dimensional, deterministic radiation transport code HZETRN.

  12. The Sierra Club--A History. Part 2: Conservation

    ERIC Educational Resources Information Center

    Strong, Douglas H.

    1977-01-01

    This second article on Sierra Club history brings the Club into the 1960s. It relates early conservation activities of the club, such as the efforts to save the Hetch Hetchy Valley. The campaign against construction of a dam in Dinosaur National Monument helped establish the club as a national organization. (MA)

  13. 13. VIEW OF RAILROAD EXHIBIT AT EL PORTAL. SHAY LOCOMOTIVE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    13. VIEW OF RAILROAD EXHIBIT AT EL PORTAL. SHAY LOCOMOTIVE IS FROM THE HETCH HETCHY RAILROAD. CABOOSE IS FROM THE YOSEMITE VALLEY RAILROAD. FOREST ROAD IN FOREGROUND IS THE ALIGNMENT OF THE YOSEMITE VALLEY RAILROAD. LOOKING W. GIS: N-37 40 27.0 / W-119 47 10.5 - Yosemite National Park Roads & Bridges, Yosemite Village, Mariposa County, CA

  14. Revisiting Runoff Model Calibration: Airborne Snow Observatory Results Allow Improved Modeling Results

    NASA Astrophysics Data System (ADS)

    McGurk, B. J.; Painter, T. H.

    2014-12-01

    Deterministic snow accumulation and ablation simulation models are widely used by runoff managers throughout the world to predict runoff quantities and timing. Model fitting is typically based on matching modeled runoff volumes and timing with observed flow time series at a few points in the basin. In recent decades, sparse networks of point measurements of the mountain snowpacks have been available to compare with modeled snowpack, but the comparability of results from a snow sensor or course to model polygons of 5 to 50 sq. km is suspect. However, snowpack extent, depth, and derived snow water equivalent have been produced by the NASA/JPL Airborne Snow Observatory (ASO) mission for spring of 20013 and 2014 in the Tuolumne River basin above Hetch Hetchy Reservoir. These high-resolution snowpack data have exposed the weakness in a model calibration based on runoff alone. The U.S. Geological Survey's Precipitation Runoff Modeling System (PRMS) calibration that was based on 30-years of inflow to Hetch Hetchy produces reasonable inflow results, but modeled spatial snowpack location and water quantity diverged significantly from the weekly measurements made by ASO during the two ablation seasons. The reason is that the PRMS model has many flow paths, storages, and water transfer equations, and a calibrated outflow time series can be right for many wrong reasons. The addition of a detailed knowledge of snow extent and water content constrains the model so that it is a better representation of the actual watershed hydrology. The mechanics of recalibrating PRMS to the ASO measurements will be described, and comparisons in observed versus modeled flow for both a small subbasin and the entire Hetch Hetchy basin will be shown. The recalibrated model provided a bitter fit to the snowmelt recession, a key factor for water managers as they balance declining inflows with demand for power generation and ecosystem releases during the final months of snow melt runoff.

  15. Airborne Snow Observatory: measuring basin-wide seasonal snowpack with LiDAR and an imaging spectrometer to improve runoff forecasting and reservoir operation (Invited)

    NASA Astrophysics Data System (ADS)

    McGurk, B. J.; Painter, T. H.

    2013-12-01

    The Airborne Snow Observatory (ASO) NASA-JPL demonstration mission collected detailed snow information for portions of the Tuolumne Basin in California and the Uncompahgre Basin in Colorado in spring of 2013. The ASO uses an imaging spectrometer and LiDAR sensors mounted in an aircraft to collect snow depth and extent data, and snow albedo. By combining ground and modeled density fields, the ~weekly flights over the Tuolumne produced both basin-wide and detailed sub-basin snow water equivalent (SWE) estimates that were used in a hydrologic simulation model to improve the accuracy and timing of runoff forecasting tools used to manage Hetch Hetchy Reservoir, the source of 85% of the water supply for 2.5 million people on the San Francisco Peninsula. The USGS PRMS simulation model was calibrated to the 459 square mile basin and was updated with both weather forecast data and distributed snow information from ASO flights to inform the reservoir operators of predicted inflow volumes and timing. Information produced by the ASO data collection was used to update distributed SWE and albedo state variables in the PRMS model and improved inflow forecasts for Hetch Hetchy. Data from operational ASO programs is expected to improve the ability of reservoir operators to more efficiently allocate the last half of the recession limb of snowmelt inflow and be more assured of meeting operational mandates. This presentation will provide results from the project after its first year.

  16. A Rapid Turn-around, Scalable Big Data Processing Capability for the JPL Airborne Snow Observatory (ASO) Mission

    NASA Astrophysics Data System (ADS)

    Mattmann, C. A.

    2014-12-01

    The JPL Airborne Snow Observatory (ASO) is an integrated LIDAR and Spectrometer measuring snow depth and rate of snow melt in the Sierra Nevadas, specifically, the Tuolumne River Basin, Sierra Nevada, California above the O'Shaughnessy Dam of the Hetch Hetchy reservoir, and the Uncompahgre Basin, Colorado, amongst other sites. The ASO data was delivered to water resource managers from the California Department of Water Resources in under 24 hours from the time that the Twin Otter aircraft landed in Mammoth Lakes, CA to the time disks were plugged in to the ASO Mobile Compute System (MCS) deployed at the Sierra Nevada Aquatic Research Laboratory (SNARL) near the airport. ASO performed weekly flights and each flight took between 500GB to 1 Terabyte of raw data, which was then processed from level 0 data products all the way to full level 4 maps of Snow Water Equivalent, albedo mosaics, and snow depth from LIDAR. These data were produced by Interactive Data analysis Language (IDL) algorithms which were then unobtrusively and automatically integrated into an Apache OODT and Apache Tika based Big Data processing system. Data movement was both electronic and physical including novel uses of LaCie 1 and 2 TeraByte (TB) data bricks and deployment in rugged terrain. The MCS was controlled remotely from the Jet Propulsion Laboratory, California Institute of Technology (JPL) in Pasadena, California on behalf of the National Aeronautics and Space Administration (NASA). Communication was aided through the use of novel Internet Relay Chat (IRC) command and control mechanisms and through the use of the Notifico open source communication tools. This talk will describe the high powered, and light-weight Big Data processing system that we developed for ASO and its implications more broadly for airborne missions at NASA and throughout the government. The lessons learned from ASO show the potential to have a large impact in the development of Big Data processing systems in the years

  17. Laboratory Tests

    MedlinePlus

    Laboratory tests check a sample of your blood, urine, or body tissues. A technician or your doctor ... compare your results to results from previous tests. Laboratory tests are often part of a routine checkup ...

  18. Laboratory Building.

    SciTech Connect

    Herrera, Joshua M.

    2015-03-01

    This report is an analysis of the means of egress and life safety requirements for the laboratory building. The building is located at Sandia National Laboratories (SNL) in Albuquerque, NM. The report includes a prescriptive-based analysis as well as a performance-based analysis. Following the analysis are appendices which contain maps of the laboratory building used throughout the analysis. The top of all the maps is assumed to be north.

  19. Laboratory Microcomputing

    PubMed Central

    York, William B.

    1984-01-01

    Microcomputers will play a major role in the laboratory, not only in the calculation and interpretation of clinical test data, but also will have an increasing place of importance in the management of laboratory resources in the face of the transition from revenue generating to the cost center era. We will give you a glimpse of what can be accomplished with the management data already collected by many laboratories today when the data are processed into meaningful reports.

  20. Laboratory Tests

    MedlinePlus

    ... Home Medical Devices Products and Medical Procedures In Vitro Diagnostics Lab Tests Laboratory Tests Share Tweet Linkedin ... Approved Home and Lab Tests Find All In Vitro Diagnostic Products and Decision Summaries Since November 2003 ...

  1. Assimilation of Airborne Snow Observatory Snow Water Equivalent to Improve Runoff Forecasting Model Performance and Reservoir Management During Warm and Dry Winters

    NASA Astrophysics Data System (ADS)

    McGurk, B. J.; Painter, T. H.

    2015-12-01

    The Airborne Snow Observatory (ASO) NASA-JPL demonstration mission has collected detailed snow information for portions of the Tuolumne Basin in California for three years, 2013 - 2015. Both 2014 and 2015 were low snow years, and 2015 was exceptionally warm and analogous to future years after climate change. The ASO uses an imaging spectrometer and LiDAR sensors mounted in an aircraft to collect snow depth and extent data, and snow albedo. By combining ground and modeled density fields, the ~weekly flights over the Tuolumne produced both basin-wide and detailed sub-basin snow water equivalent (SWE) estimates that were provided to Hetch Hetchy Reservoir operators. The data were also assimilated into an hydrologic simulation model in an attempt to improve the accuracy and timing of a runoff forecasting tool that can be used to improve the management of Hetch Hetchy Reservoir, the source of 85% of the water supply for 2.6 million people on the San Francisco Peninsula. The USGS Precipitation Runoff Modeling System was calibrated to the 1181 square kilometer basin and simulation results compared to observed runoff with and without assimilation of ASO data. Simulated and observed were also compared with observed with both single updates associated with each flight, and with sequential updates from each flight. Sequential updating was found to improve correlation between observed and simulated reservoir inflows, and there by improve the ability of reservoir operators to more efficiently allocate the last half of the recession limb of snowmelt inflow and be assured of filling the reservoir and minimizing ecologically-damaging late season spills.

  2. Hillslope Erosion and Water Quality from the Rim Fire, Sierra Nevada, CA

    NASA Astrophysics Data System (ADS)

    Kuhn, T. J.; Austin, L. J.; Forrester, H.; DeLong, S. B.; Lever, R.; Roche, J. W.

    2014-12-01

    The Rim Fire in 2013 burned approximately 1036 km2 in the Sierra Nevada (including 312 km2 within Yosemite National Park), generating considerable public concern regarding potential impacts to the Tuolumne River watershed, in terms of water quality and water supply infrastructure serving the City of San Francisco. Land management responses included a multi-million dollar watershed treatment project on USFS lands near Cherry Creek, with similar actions suggested for areas in the Hetch Hetchy and Lake Eleanor watersheds. In response to the concern that the post-burn landscape will negatively impact water quality, we are investigating hydrologic effects and hillslope erosion in two small burned basins (2.2 and 5.2 km2) within the Tuolumne River basin in Yosemite National Park. Within a month after fire containment, sites were equipped with instrumentation to record stream stage, turbidity, and total suspended sediment. We also installed 21 sediment fences that trap all sediment silt sized and larger on moderate (20%) to steep (50%) hillslopes from 100 m2 plots within moderate and high severity burn areas. Accumulated sediment is collected, weighed, and sub-sampled after each storm event, and, analyzed for dry weight, particle size, gravimetric water content, bulk density, pH, color, carbon and nitrogen content from % fine organics, and % coarse organics. As of July 31, 2014, four discrete storm events had been sampled. Data are used to calculate annual sediment yield, and to investigate organic carbon storage, deposition, and transport. We are also collecting repeat terrestrial laser scans to assess topographic change and identify the hillslope processes that contribute to erosion and deposition at plot- and hillslope-scale. These findings provide analogs for possible changes in adjacent burned areas and to inform management decisions in response to future fires and potential impacts to water quality in areas valued by the park, the City of San Francisco and other

  3. Laboratory Buildings.

    ERIC Educational Resources Information Center

    Barnett, Jonathan

    The need for flexibility in science research facilities is discussed, with emphasis on the effect of that need on the design of laboratories. The relationship of office space, bench space, and special equipment areas, and the location and distribution of piping and air conditioning, are considered particularly important. This building type study…

  4. Laboratory diagnosis

    Technology Transfer Automated Retrieval System (TEKTRAN)

    One of the first major goals of the microbiology laboratory is to isolate or detect clinically significant microorganisms from an affected site and, if more than one type of microorganism is present, to isolate them in approximately the same ratio as occurs in vivo. Whether an isolate is “clinically...

  5. Lunar laboratory

    SciTech Connect

    Keaton, P.W.; Duke, M.B.

    1986-01-01

    An international research laboratory can be established on the Moon in the early years of the 21st Century. It can be built using the transportation system now envisioned by NASA, which includes a space station for Earth orbital logistics and orbital transfer vehicles for Earth-Moon transportation. A scientific laboratory on the Moon would permit extended surface and subsurface geological exploration; long-duration experiments defining the lunar environment and its modification by surface activity; new classes of observations in astronomy; space plasma and fundamental physics experiments; and lunar resource development. The discovery of a lunar source for propellants may reduce the cost of constructing large permanent facilities in space and enhance other space programs such as Mars exploration. 29 refs.

  6. Laboratory Activities

    SciTech Connect

    Brown, Christopher F.; Serne, R. Jeffrey

    2008-01-17

    This chapter summarizes the laboratory activities performed by PNNL’s Vadose Zone Characterization Project in support of the Tank Farm Vadose Zone Program, led by CH2M HILL Hanford Group, Inc. The results of these studies are contained in numerous reports (Lindenmeier et al. 2002; Serne et al. 2002a, 2002b, 2002c, 2002d, 2002e; Lindenmeier et al. 2003; Serne et al. 2004a, 2004b; Brown et al. 2005, 2006a, 2007; Serne et al. 2007) and have generated much of the data reported in Chapter 22 (Geochemistry-Contaminant Movement), Appendix G (Geochemistry-Contaminant Movement), and Cantrell et al. (2007, SST WMA Geochemistry Data Package – in preparation). Sediment samples and characterization results from PNNL’s Vadose Zone Characterization Project are also shared with other science and technology (S&T) research projects, such as those summarized in Chapter 12 (Associated Science Activities).

  7. Laboratory investigations

    NASA Technical Reports Server (NTRS)

    Russell, Ray W.

    1988-01-01

    Laboratory studies related to cometary grains and the nuclei of comets can be broken down into three areas which relate to understanding the spectral properties, the formation mechanisms, and the evolution of grains and nuclei: (1) Spectral studies to be used in the interpretation of cometary spectra; (2) Sample preparation experiments which may shed light on the physical nature and history of cometary grains and nuclei by exploring the effects on grain emissivities resulting from the ways in which the samples are created; and (3) Grain processing experiments which should provide insight on the interaction of cometary grains with the environment in the immediate vicinity of the cometary nucleus as the comet travels from the Oort cloud through perihelion, and perhaps even suggestions regarding the relationship between interstellar grains and cometary matter. A summary is presented with a different view of lab experiments than is found in the literature, concentrating on measurement techniques and sample preparations especially relevant to cometary dust.

  8. Chemistry Laboratory Safety Check

    ERIC Educational Resources Information Center

    Patnoe, Richard L.

    1976-01-01

    An accident prevention/safety check list for chemistry laboratories is printed. Included are checks of equipment, facilities, storage and handling of chemicals, laboratory procedures, instruction procedures, and items to be excluded from chemical laboratories. (SL)

  9. [Theme: Using Laboratories.

    ERIC Educational Resources Information Center

    Pritchard, Jack; Braker, Clifton

    1982-01-01

    Pritchard discusses the opportunities for applied learning afforded by laboratories. Braker describes the evaluation of cognitive, affective, and psychomotor skills in the agricultural mechanics laboratory. (SK)

  10. Laboratory Information Systems.

    PubMed

    Henricks, Walter H

    2015-06-01

    Laboratory information systems (LISs) supply mission-critical capabilities for the vast array of information-processing needs of modern laboratories. LIS architectures include mainframe, client-server, and thin client configurations. The LIS database software manages a laboratory's data. LIS dictionaries are database tables that a laboratory uses to tailor an LIS to the unique needs of that laboratory. Anatomic pathology LIS (APLIS) functions play key roles throughout the pathology workflow, and laboratories rely on LIS management reports to monitor operations. This article describes the structure and functions of APLISs, with emphasis on their roles in laboratory operations and their relevance to pathologists. PMID:26065785

  11. Laboratory Information Systems.

    PubMed

    Henricks, Walter H

    2016-03-01

    Laboratory information systems (LISs) supply mission-critical capabilities for the vast array of information-processing needs of modern laboratories. LIS architectures include mainframe, client-server, and thin client configurations. The LIS database software manages a laboratory's data. LIS dictionaries are database tables that a laboratory uses to tailor an LIS to the unique needs of that laboratory. Anatomic pathology LIS (APLIS) functions play key roles throughout the pathology workflow, and laboratories rely on LIS management reports to monitor operations. This article describes the structure and functions of APLISs, with emphasis on their roles in laboratory operations and their relevance to pathologists. PMID:26851660

  12. Laboratory Animal Facilities. Laboratory Design Notes.

    ERIC Educational Resources Information Center

    Jonas, Albert M.

    1965-01-01

    Design of laboratory animal facilities must be functional. Accordingly, the designer should be aware of the complex nature of animal research and specifically the type of animal research which will be conducted in a new facility. The building of animal-care facilities in research institutions requires special knowledge in laboratory animal…

  13. Tethered gravity laboratories study

    NASA Technical Reports Server (NTRS)

    Lucchetti, F.

    1989-01-01

    Tethered gravity laboratories study is presented. The following subject areas are covered: variable gravity laboratory; attitude tether stabilizer; configuration analysis (AIT); dynamic analysis (SAO); and work planned for the next reporting period.

  14. An Electronics "Unit Laboratory"

    ERIC Educational Resources Information Center

    Davies, E. R.; Penton, S. J.

    1976-01-01

    Describes a laboratory teaching technique in which a single topic (in this case, bipolar junction transistors) is studied over a period of weeks under the supervision of one staff member, who also designs the laboratory work. (MLH)

  15. Employment at National Laboratories

    SciTech Connect

    E. S. Peterson; C. A. Allen

    2007-04-01

    Scientists enter the National Laboratory System for many different reasons. For some, faculty positions are scarce, so they take staff-scientist position at national laboratories (i.e. Pacific Northwest, Idaho, Los Alamos, and Brookhaven). Many plan to work at the National Laboratory for 5 to 7 years and then seek an academic post. For many (these authors included), before they know it it’s 15 or 20 years later and they never seriously considered leaving the laboratory system.

  16. EPA Environmental Chemistry Laboratory

    NASA Technical Reports Server (NTRS)

    1993-01-01

    The Environmental Protection Agency's (EPA) Chemistry Laboratory (ECL) is a national program laboratory specializing in residue chemistry analysis under the jurisdiction of the EPA's Office of Pesticide Programs in Washington, D.C. At Stennis Space Center, the laboratory's work supports many federal anti-pollution laws. The laboratory analyzes environmental and human samples to determine the presence and amount of agricultural chemicals and related substances. Pictured, ECL chemists analyze environmental and human samples for the presence of pesticides and other pollutants.

  17. Undergraduate Chemistry Laboratory

    ERIC Educational Resources Information Center

    Bretz, Stacey Lowery; Fay, Michael; Bruck, Laura B.; Towns, Marcy H.

    2013-01-01

    Forty chemistry faculty from American Chemical Society-approved departments were interviewed to determine their goals for undergraduate chemistry laboratory. Faculty were stratified by type of institution, departmental success with regard to National Science Foundation funding for laboratory reform, and level of laboratory course. Interview…

  18. Laboratory Activities in Israel

    ERIC Educational Resources Information Center

    Mamlok-Naaman, Rachel; Barnea, Nitza

    2012-01-01

    Laboratory activities have long had a distinctive and central role in the science curriculum, and science educators have suggested that many benefits accrue from engaging students in science laboratory activities. Many research studies have been conducted to investigate the educational effectiveness of laboratory work in science education in…

  19. INL Laboratory Scale Atomizer

    SciTech Connect

    C.R. Clark; G.C. Knighton; R.S. Fielding; N.P. Hallinan

    2010-01-01

    A laboratory scale atomizer has been built at the Idaho National Laboratory. This has proven useful for laboratory scale tests and has been used to fabricate fuel used in the RERTR miniplate experiments. This instrument evolved over time with various improvements being made ‘on the fly’ in a trial and error process.

  20. Laboratory Equipment Criteria.

    ERIC Educational Resources Information Center

    State Univ. Construction Fund, Albany, NY.

    Requirements for planning, designing, constructing and installing laboratory furniture are given in conjunction with establishing facility criteria for housing laboratory equipment. Furniture and equipment described include--(1) center tables, (2) reagent racks, (3) laboratory benches and their mechanical fixtures, (4) sink and work counters, (5)…

  1. Laboratory Ventilation and Safety.

    ERIC Educational Resources Information Center

    Steere, Norman V.

    1965-01-01

    In order to meet the needs of both safety and economy, laboratory ventilation systems must effectively remove air-borne toxic and flammable materials and at the same time exhaust a minimum volume of air. Laboratory hoods are the most commonly used means of removing gases, dusts, mists, vapors, and fumed from laboratory operations. To be effective,…

  2. Theme: Laboratory Instruction.

    ERIC Educational Resources Information Center

    Bruening, Thomas H.; And Others

    1992-01-01

    A series of theme articles discuss setting up laboratory hydroponics units, the school farm at the Zuni Pueblo in New Mexico, laboratory experiences in natural resources management and urban horticulture, the development of teaching labs at Derry (PA) High School, management of instructional laboratories, and industry involvement in agricultural…

  3. Los Alamos National Laboratory.

    ERIC Educational Resources Information Center

    Hammel, Edward F., Jr.

    1982-01-01

    Current and post World War II scientific research at the Los Alamos National Laboratory (New Mexico) is discussed. The operation of the laboratory, the Los Alamos consultant program, and continuation education, and continuing education activities at the laboratory are also discussed. (JN)

  4. Laboratory Turnaround Time

    PubMed Central

    Hawkins, Robert C

    2007-01-01

    Turnaround time (TAT) is one of the most noticeable signs of laboratory service and is often used as a key performance indicator of laboratory performance. This review summarises the literature regarding laboratory TAT, focusing on the different definitions, measures, expectations, published data, associations with clinical outcomes and approaches to improve TAT. It aims to provide a consolidated source of benchmarking data useful to the laboratory in setting TAT goals and to encourage introduction of TAT monitoring for continuous quality improvement. A 90% completion time (sample registration to result reporting) of <60 minutes for common laboratory tests is suggested as an initial goal for acceptable TAT. PMID:18392122

  5. Skylab mobile laboratory

    NASA Technical Reports Server (NTRS)

    Primeaux, G. R.; Larue, M. A.

    1975-01-01

    The Skylab mobile laboratory was designed to provide the capability to obtain necessary data on the Skylab crewmen 30 days before lift-off, within 1 hour after recovery, and until preflight physiological baselines were reattained. The mobile laboratory complex consisted of six laboratories that supported cardiovascular, metabolic, nutrition and endocrinology, operational medicine, blood, and microbiology experiments; a utility package; and two shipping containers. The objectives and equipment requirements of the Skylab mobile laboratory and the data acquisition systems are discussed along with processes such as permanently mounting equipment in the individual laboratories and methods of testing and transporting the units. The operational performance, in terms of amounts of data collected, and the concept of mobile laboratories for medical and scientific experiments are evaluated. The Skylab mobile laboratory succeeded in facilitating the data collection and sample preservation associated with the three Skylab manned flights.

  6. Standards Laboratory environments

    SciTech Connect

    Braudaway, D.W.

    1990-09-01

    Standards Laboratory environments need to be carefully selected to meet the specific mission of each laboratory. The mission of the laboratory depends on the specific work supported, the measurement disciplines required and the level of uncertainty required in the measurements. This document reproduces the contents of the Sandia National Laboratories Primary Standards Laboratory Memorandum Number 3B (PSLM-3B) which was issued on May 16, 1988, under the auspices of the Department of Energy, Albuquerque Operations Office, to guide the laboratories of the Nuclear Weapons Complex in selecting suitable environments. Because of both general interest and specific interest in Standards Laboratory environments this document is being issued in a more available form. The purpose of this document is to provide guidance in selection of laboratory environments suitable for standards maintenance and calibration operations. It is not intended to mandate a specific environment for a specific calibration but to direct selection of the environment and to offer suggestions on how to extend precision in an existing and/or achievable (practical) environment. Although this documents pertains specifically to standards laboratories, it can be applied to any laboratory requiring environmental control.

  7. Laboratory Astrophysics White Paper

    NASA Technical Reports Server (NTRS)

    Brickhouse, Nancy; Federman, Steve; Kwong, Victor; Salama, Farid; Savin, Daniel; Stancil, Phillip; Weingartner, Joe; Ziurys, Lucy

    2006-01-01

    Laboratory astrophysics and complementary theoretical calculations are the foundations of astronomical and planetary research and will remain so for many generations to come. From the level of scientific conception to that of the scientific return, it is our understanding of the underlying processes that allows us to address fundamental questions regarding the origins and evolution of galaxies, stars, planetary systems, and life in the cosmos. In this regard, laboratory astrophysics is much like detector and instrument development at NASA and NSF; these efforts are necessary for the astronomical research being funded by the agencies. The NASA Laboratory Astrophysics Workshop met at the University of Nevada, Las Vegas (UNLV) from 14-16 February, 2006 to identify the current laboratory data needed to support existing and future NASA missions and programs in the Astrophysics Division of the Science Mission Directorate (SMD). Here we refer to both laboratory and theoretical work as laboratory astrophysics unless a distinction is necessary. The format for the Workshop involved invited talks by users of laboratory data, shorter contributed talks and poster presentations by both users and providers that highlighted exciting developments in laboratory astrophysics, and breakout sessions where users and providers discussed each others' needs and limitations. We also note that the members of the Scientific Organizing Committee are users as well as providers of laboratory data. As in previous workshops, the focus was on atomic, molecular, and solid state physics.

  8. Sandia National Laboratories

    NASA Technical Reports Server (NTRS)

    Gilliom, Laura R.

    1992-01-01

    Sandia National Laboratories has identified technology transfer to U.S. industry as a laboratory mission which complements our national security mission and as a key component of the Laboratory's future. A number of technology transfer mechanisms - such as CRADA's, licenses, work-for-others, and consortia - are identified and specific examples are given. Sandia's experience with the Specialty Metals Processing Consortium is highlighted with a focus on the elements which have made it successful. A brief discussion of Sandia's potential interactions with NASA under the Space Exploration Initiative was included as an example of laboratory-to-NASA technology transfer. Viewgraphs are provided.

  9. Hoods for Science Laboratories.

    ERIC Educational Resources Information Center

    Horowitz, Harold; and others

    Detailed discussions are presented dealing with the selection and design of fume hoods for science laboratories. Areas covered include--(1) air flow design, (2) materials properties, (3) location in the laboratory, (4) testing and adjustment, (5) exhaust systems, and (6) hazards of fume discharges. (JT)

  10. The Virtual Robotics Laboratory

    SciTech Connect

    Kress, R.L.; Love, L.J.

    1999-09-01

    The growth of the Internet has provided a unique opportunity to expand research collaborations between industry, universities, and the national laboratories. The Virtual Robotics Laboratory (VRL) is an innovative program at Oak Ridge National Laboratory (ORNL) that is focusing on the issues related to collaborative research through controlled access of laboratory equipment using the World Wide Web. The VRL will provide different levels of access to selected ORNL laboratory secondary education programs. In the past, the ORNL Robotics and Process Systems Division has developed state-of-the-art robotic systems for the Army, NASA, Department of Energy, Department of Defense, as well as many other clients. After proof of concept, many of these systems sit dormant in the laboratories. This is not out of completion of all possible research topics. but from completion of contracts and generation of new programs. In the past, a number of visiting professors have used this equipment for their own research. However, this requires that the professor, and possibly his/her students, spend extended periods at the laboratory facility. In addition, only a very exclusive group of faculty can gain access to the laboratory and hardware. The VRL is a tool that enables extended collaborative efforts without regard to geographic limitations.

  11. Dental Laboratory Technician.

    ERIC Educational Resources Information Center

    Ohio State Univ., Columbus. Center on Education and Training for Employment.

    This document, which is designed for use in developing a tech prep competency profile for the occupation of dental laboratory technician, lists technical competencies and competency builders for 13 units pertinent to the health technologies cluster in general and 8 units to the occupation of dental laboratory technician. The following skill areas…

  12. NVLAP calibration laboratory program

    SciTech Connect

    Cigler, J.L.

    1993-12-31

    This paper presents an overview of the progress up to April 1993 in the development of the Calibration Laboratories Accreditation Program within the framework of the National Voluntary Laboratory Accreditation Program (NVLAP) at the National Institute of Standards and Technology (NIST).

  13. Technology Systems. Laboratory Activities.

    ERIC Educational Resources Information Center

    Brame, Ray; And Others

    This guide contains 43 modules of laboratory activities for technology education courses. Each module includes an instructor's resource sheet and the student laboratory activity. Instructor's resource sheets include some or all of the following elements: module number, course title, activity topic, estimated time, essential elements, objectives,…

  14. The Virtual Robotics Laboratory

    SciTech Connect

    Kress, R.L.; Love, L.J.

    1997-03-01

    The growth of the Internet has provided a unique opportunity to expand research collaborations between industry, universities, and the national laboratories. The Virtual Robotics Laboratory (VRL) is an innovative program at Oak Ridge National Laboratory (ORNL) that is focusing on the issues related to collaborative research through controlled access of laboratory equipment using the World Wide Web. The VRL will provide different levels of access to selected ORNL laboratory equipment to outside universities, industrial researchers, and elementary and secondary education programs. In the past, the ORNL Robotics and Process Systems Division (RPSD) has developed state-of-the-art robotic systems for the Army, NASA, Department of Energy, Department of Defense, as well as many other clients. After proof of concept, many of these systems sit dormant in the laboratories. This is not out of completion of all possible research topics, but from completion of contracts and generation of new programs. In the past, a number of visiting professors have used this equipment for their own research. However, this requires that the professor, and possibly his students, spend extended periods at the laboratory facility. In addition, only a very exclusive group of faculty can gain access to the laboratory and hardware. The VRL is a tool that enables extended collaborative efforts without regard to geographic limitations.

  15. Quality in Teaching Laboratories.

    ERIC Educational Resources Information Center

    Stubington, John F.

    1995-01-01

    Describes a Japanese process-oriented approach called KAIZEN for improving the quality of existing teaching laboratories. It provides relevant quality measurements and indicates how quality can be improved. Use of process criteria sidesteps the difficulty of defining quality for laboratory experiments and allows separation of student assessment…

  16. The Language Laboratory.

    ERIC Educational Resources Information Center

    Hocking, Elton

    This condensed article on the language laboratory describes educational and financial possibilities and limitations, often citing the foreign language program at Purdue University as an example. The author discusses: (1) costs and amortization, (2) preventive maintenance, (3) laboratory design, (4) the multichannel recorder, and (5) visuals. Other…

  17. Dental Laboratory Technology.

    ERIC Educational Resources Information Center

    Department of the Air Force, Washington, DC.

    The Air Force dental laboratory technology manual is designed as a basic training text as well as a reference source for dental laboratory technicians, a specialty occupation concerned with the design, fabrication, and repair of dental prostheses. Numerous instructive diagrams and photographs are included throughout the manual. The comprehensive…

  18. Practical Laboratory Planning.

    ERIC Educational Resources Information Center

    Ferguson, W. R.

    This book is intended as a guide for people who are planning chemistry and physics research laboratories. It deals with the importance of effective communication between client and architect, the value of preliminary planning, and the role of the project officer. It also discusses the size and layout of individual laboratories, the design of…

  19. Biotechnology Laboratory Methods.

    ERIC Educational Resources Information Center

    Davis, Robert H.; Kompala, Dhinakar S.

    1989-01-01

    Describes a course entitled "Biotechnology Laboratory" which introduces a variety of laboratory methods associated with biotechnology. Describes the history, content, and seven experiments of the course. The seven experiments are selected from microbiology and molecular biology, kinetics and fermentation, and downstream processing-bioseparations.…

  20. Medical Laboratory Technician.

    ERIC Educational Resources Information Center

    Ohio State Univ., Columbus. Center on Education and Training for Employment.

    This document, which is designed for use in developing a tech prep competency profile for the occupation of medical laboratory technician, lists technical competencies and competency builders for 18 units pertinent to the health technologies cluster in general and 8 units specific to the occupation of medical laboratory technician. The following…

  1. Laboratory for Oceans

    NASA Technical Reports Server (NTRS)

    1988-01-01

    A review is made of the activities of the Laboratory for Oceans. The staff and the research activities are nearly evenly divided between engineering and scientific endeavors. The Laboratory contributes engineering design skills to aircraft and ground based experiments in terrestrial and atmospheric sciences in cooperation with scientists from labs in Earth sciences.

  2. LANGUAGE ARTS LABORATORY.

    ERIC Educational Resources Information Center

    ROBERTS, HERMESE E.

    THE LANGUAGE ARTS LABORATORY WAS ESTABLISHED TO IMPROVE READING ABILITY AND OTHER LANGUAGE ARTS SKILLS AS AN AID IN THE PREVENTION OF DROPOUTS. THE LABORATORY WAS OPERATED ON A SUMMER SCHEDULE WITH A FLEXIBLE PROGRAM OF FROM 45 MINUTES TO 2 1/2 HOURS DAILY. ALL PUPILS WERE 14 YEARS OF AGE OR OLDER, AND EXPRESSED A DESIRE TO IMPROVE THEIR READING…

  3. Primary Standards Laboratory report

    SciTech Connect

    Not Available

    1990-12-01

    Sandia National Laboratories operates the Primary Standards Laboratory (PSL) for the Department of Energy, Albuquerque Operations Office (DOE/AL). This report summarizes metrology activities that received emphasis in the first half of 1990 and provides information pertinent to the operation of the DOE/AL system-wide Standards and Calibration Program.

  4. Carbon Characterization Laboratory Report

    SciTech Connect

    David Swank; William Windes; D.C. Haggard; David Rohrbaugh; Karen Moore

    2009-03-01

    The newly completed Idaho National Laboratory (INL) Carbon Characterization Laboratory (CCL) is located in Lab-C20 of the Idaho National Laboratory Research Center. This laboratory was established under the Next Generation Nuclear Plant (NGNP) Project to support graphite research and development activities. The CCL is designed to characterize and test carbon-based materials such as graphite, carbon-carbon composites, and silicon-carbide composite materials. The laboratory is fully prepared to measure material properties for nonirradiated carbon-based materials. Plans to establish the laboratory as a radiological facility within the next year are definitive. This laboratory will be modified to accommodate irradiated materials, after which it can be used to perform material property measurements on both irradiated and nonirradiated carbon-based material. Instruments, fixtures, and methods are in place for preirradiation measurements of bulk density, thermal diffusivity, coefficient of thermal expansion, elastic modulus, Young’s modulus, Shear modulus, Poisson ratio, and electrical resistivity. The measurement protocol consists of functional validation, calibration, and automated data acquisition.

  5. The laboratory module

    NASA Astrophysics Data System (ADS)

    Of the five modules comprising the Orbiting Quarantine Facility, the Laboratory Module must provide not only an extensive research capability to permit execution of the protocol, but also the flexibility to accommodate second-order testing if nonterrestrial life is discovered in the sample. The biocontainment barriers that protect the sample and the researchers from cross contamination are described. Specifically, the laboratory layout, laboratory equipment, the environmental control and life support system, and containment assurance procedures are discussed. The metal manipulation arm proposed for use within the biocontainment cabinets is described. Sample receipt and processing procedures are outlined.

  6. Specialized Laboratory Information Systems.

    PubMed

    Dangott, Bryan

    2016-03-01

    Some laboratories or laboratory sections have unique needs that traditional anatomic and clinical pathology systems may not address. A specialized laboratory information system (LIS), which is designed to perform a limited number of functions, may perform well in areas where a traditional LIS falls short. Opportunities for specialized LISs continue to evolve with the introduction of new testing methodologies. These systems may take many forms, including stand-alone architecture, a module integrated with an existing LIS, a separate vendor-supplied module, and customized software. This article addresses the concepts underlying specialized LISs, their characteristics, and in what settings they are found. PMID:26851663

  7. Sonication standard laboratory module

    DOEpatents

    Beugelsdijk, Tony; Hollen, Robert M.; Erkkila, Tracy H.; Bronisz, Lawrence E.; Roybal, Jeffrey E.; Clark, Michael Leon

    1999-01-01

    A standard laboratory module for automatically producing a solution of cominants from a soil sample. A sonication tip agitates a solution containing the soil sample in a beaker while a stepper motor rotates the sample. An aspirator tube, connected to a vacuum, draws the upper layer of solution from the beaker through a filter and into another beaker. This beaker can thereafter be removed for analysis of the solution. The standard laboratory module encloses an embedded controller providing process control, status feedback information and maintenance procedures for the equipment and operations within the standard laboratory module.

  8. Laboratory Automation and Middleware.

    PubMed

    Riben, Michael

    2015-06-01

    The practice of surgical pathology is under constant pressure to deliver the highest quality of service, reduce errors, increase throughput, and decrease turnaround time while at the same time dealing with an aging workforce, increasing financial constraints, and economic uncertainty. Although not able to implement total laboratory automation, great progress continues to be made in workstation automation in all areas of the pathology laboratory. This report highlights the benefits and challenges of pathology automation, reviews middleware and its use to facilitate automation, and reviews the progress so far in the anatomic pathology laboratory. PMID:26065792

  9. Safety in Science Laboratories.

    ERIC Educational Resources Information Center

    Education in Science, 1978

    1978-01-01

    Presents 12 amendments to the second edition of Safety in Science Laboratories. Covers topics such as regular inspection of equipment, wearing safety glasses, dating stock chemicals, and safe use of chemicals. (MA)

  10. Ecosystems in the Laboratory

    ERIC Educational Resources Information Center

    Madders, M.

    1975-01-01

    Describes the materials and laboratory techniques for the study of food chains and food webs, pyramids of numbers and biomass, energy pyramids, and oxygen gradients. Presents a procedure for investigating the effects of various pollutants on an entire ecosystem. (GS)

  11. Organic Laboratory Experiments.

    ERIC Educational Resources Information Center

    Smith, Sherrel

    1990-01-01

    Detailed is a method in which short pieces of teflon tubing may be used for collection tubes for collecting preparative fractions from gas chromatographs. Material preparation, laboratory procedures, and results of this method are discussed. (CW)

  12. Understanding Laboratory Tests

    MedlinePlus

    ... and Drug Administration (FDA) regulates the development and marketing of all laboratory tests that use test kits ... at the National Institutes of Health FOLLOW US Facebook Twitter Instagram YouTube Google+ LinkedIn GovDelivery RSS CONTACT ...

  13. Tethered gravity laboratories study

    NASA Technical Reports Server (NTRS)

    Lucchetti, F.

    1989-01-01

    Variable Gravity Laboratory studies are discussed. The following subject areas are covered: (1) conceptual design and engineering analysis; (2) control strategies (fast crawling maneuvers, main perturbations and their effect upon the acceleration level); and (3) technology requirements.

  14. RAS Laboratory Groups

    Cancer.gov

    The RAS Initiative uses multiple technologies to attack RAS-driven cancers. The resources of the Frederick National Lab allocated to the RAS Hub are organized into seven laboratory groups, each contributing to the collaborative effort.

  15. Physics Laboratory in UEC

    NASA Astrophysics Data System (ADS)

    Takada, Tohru; Nakamura, Jin; Suzuki, Masaru

    All the first-year students in the University of Electro-Communications (UEC) take "Basic Physics I", "Basic Physics II" and "Physics Laboratory" as required subjects; Basic Physics I and Basic Physics II are calculus-based physics of mechanics, wave and oscillation, thermal physics and electromagnetics. Physics Laboratory is designed mainly aiming at learning the skill of basic experimental technique and technical writing. Although 95% students have taken physics in the senior high school, they poorly understand it by connecting with experience, and it is difficult to learn Physics Laboratory in the university. For this reason, we introduced two ICT (Information and Communication Technology) systems of Physics Laboratory to support students'learning and staff's teaching. By using quantitative data obtained from the ICT systems, we can easily check understanding of physics contents in students, and can improve physics education.

  16. NETL - Thermogravimetric Analysis Laboratory

    SciTech Connect

    Richards, George

    2013-06-12

    Researchers in NETL's Thermal Analysis Laboratory are investigating chemical looping combustion. As a clean and efficient fossil fuel technology, chemical looping combustion controls CO2 emissions and offers a promising alternative to traditional combustion.

  17. Microcontrollers in the Laboratory.

    ERIC Educational Resources Information Center

    Williams, Ron

    1989-01-01

    Described is the use of automated control using microcomputers. Covers the development of the microcontroller and describes advantages and characteristics of several brands of chips. Provides several recent applications of microcontrollers in laboratory automation. (MVL)

  18. Retainer for laboratory animals

    NASA Technical Reports Server (NTRS)

    Lee, R. W.

    1979-01-01

    Bio-retainer holds laboratory animals in fixed position for research and clinical experiments. Retainer allows full access to animals and can be rapidly opened and closed to admit and release specimens.

  19. ENVIRONMENTAL RESEARCH LABORATORY - CORVALLIS

    EPA Science Inventory

    The Environmental Research Laboratory - Corvallis is the U.S. Environmental Protection Agency's - national research center for terrestrial and watershed ecology, aquatic ecoregions, and for the ecological effects of climate change, stratospheric ozone depletion, and atmospheric p...

  20. Theory and laboratory astrophysics

    NASA Technical Reports Server (NTRS)

    Schramm, David N.; Mckee, Christopher F.; Alcock, Charles; Allamandola, Lou; Chevalier, Roger A.; Cline, David B.; Dalgarno, Alexander; Elmegreen, Bruce G.; Fall, S. Michael; Ferland, Gary J.

    1991-01-01

    Science opportunities in the 1990's are discussed. Topics covered include the large scale structure of the universe, galaxies, stars, star formation and the interstellar medium, high energy astrophysics, and the solar system. Laboratory astrophysics in the 1990's is briefly surveyed, covering such topics as molecular, atomic, optical, nuclear and optical physics. Funding recommendations are given for the National Science Foundation, NASA, and the Department of Energy. Recommendations for laboratory astrophysics research are given.

  1. POLLUTION PREVENTION OPPORTUNITY ASSESSMENT - GEOCHEMISTRY LABORATORY AT SANDIA NATIONAL LABORATORIES

    EPA Science Inventory

    These reports summarize pollution prevention opportunity assessments conducted jointly by EPA and DOE at the Geochemistry Laboratory and the Manufacturing and Fabrication Repair Laboratory at the Department of Energy's Sandia National Laboratories facility in Albuquerque, New Mex...

  2. Development of the Design Laboratory.

    ERIC Educational Resources Information Center

    Silla, Harry

    1986-01-01

    Describes the design laboratory at the Stevens Institute of Technology (SIT). Considers course objectives, design projects, project structure, mechanical design, project management, and laboratory operation. This laboratory complements SIT's course in process design, giving students a complete design experience. (JN)

  3. Laboratory safety handbook

    USGS Publications Warehouse

    Skinner, E.L.; Watterson, C.A.; Chemerys, J.C.

    1983-01-01

    Safety, defined as 'freedom from danger, risk, or injury,' is difficult to achieve in a laboratory environment. Inherent dangers, associated with water analysis and research laboratories where hazardous samples, materials, and equipment are used, must be minimized to protect workers, buildings, and equipment. Managers, supervisors, analysts, and laboratory support personnel each have specific responsibilities to reduce hazards by maintaining a safe work environment. General rules of conduct and safety practices that involve personal protection, laboratory practices, chemical handling, compressed gases handling, use of equipment, and overall security must be practiced by everyone at all levels. Routine and extensive inspections of all laboratories must be made regularly by qualified people. Personnel should be trained thoroughly and repetitively. Special hazards that may involve exposure to carcinogens, cryogenics, or radiation must be given special attention, and specific rules and operational procedures must be established to deal with them. Safety data, reference materials, and texts must be kept available if prudent safety is to be practiced and accidents prevented or minimized.

  4. NASA's Propulsion Research Laboratory

    NASA Technical Reports Server (NTRS)

    2004-01-01

    The grand opening of NASA's new, world-class laboratory for research into future space transportation technologies located at the Marshall Space Flight Center (MSFC) in Huntsville, Alabama, took place in July 2004. The state-of-the-art Propulsion Research Laboratory (PRL) serves as a leading national resource for advanced space propulsion research. Its purpose is to conduct research that will lead to the creation and development of innovative propulsion technologies for space exploration. The facility is the epicenter of the effort to move the U.S. space program beyond the confines of conventional chemical propulsion into an era of greatly improved access to space and rapid transit throughout the solar system. The laboratory is designed to accommodate researchers from across the United States, including scientists and engineers from NASA, the Department of Defense, the Department of Energy, universities, and industry. The facility, with 66,000 square feet of useable laboratory space, features a high degree of experimental capability. Its flexibility allows it to address a broad range of propulsion technologies and concepts, such as plasma, electromagnetic, thermodynamic, and propellant propulsion. An important area of emphasis is the development and utilization of advanced energy sources, including highly energetic chemical reactions, solar energy, and processes based on fission, fusion, and antimatter. The Propulsion Research Laboratory is vital for developing the advanced propulsion technologies needed to open up the space frontier, and sets the stage of research that could revolutionize space transportation for a broad range of applications.

  5. Space Food Systems Laboratory

    NASA Technical Reports Server (NTRS)

    Perchonok, Michele; Russo, Dane M. (Technical Monitor)

    2001-01-01

    The Space Food Systems Laboratory (SFSL) is a multipurpose laboratory responsible for space food and package research and development. It is located on-site at Johnson Space Center in Building 17. The facility supports the development of flight food, menus, packaging and food related hardware for Shuttle, International Space Station, and Advanced Life Support food systems. All foods used to support NASA ground tests and/or missions must meet the highest standards before they are 'accepted' for use on actual space flights. The foods are evaluated for nutritional content, sensory acceptability, safety, storage and shelf life, and suitability for use in micro-gravity. The food packaging is also tested to determine its functionality and suitability for use in space. Food Scientist, Registered Dieticians, Packaging Engineers, Food Systems Engineers, and Technicians staff the Space Food Systems Laboratory.

  6. Evaluating Astronomy Laboratories

    NASA Astrophysics Data System (ADS)

    Zirbel, E. L.

    2002-12-01

    A set of non-traditional astronomy laboratories for non-science majors will be presented along with evaluations of lab technicians (these labs were originally developed at the College of Staten Island of the City University of New York). The goal of these labs is twofold: (a) to provide the students with hands-on experiences of scientific methodology and (b) to provoke critical thinking. Because non-science majors are often rather resistant to learning the relevant methodology - and especially to thinking critically - this manual is structured differently. It does not only provide traditional cook-book recipes but also contains several leading questions to make the students realize why they are doing what. The students are encouraged to write full sentences and explain how they reach which conclusions. This poster summarizes the experiences of the laboratory assistants that worked with the instructor and presents how they judge the effectiveness of the laboratories.

  7. Exploration Laboratory Analysis - ARC

    NASA Technical Reports Server (NTRS)

    Krihak, Michael K.; Fung, Paul P.

    2012-01-01

    The Exploration Laboratory Analysis (ELA) project supports the Exploration Medical Capability (ExMC) risk, Risk of Inability to Adequately Treat an Ill or Injured Crew Member, and ExMC Gap 4.05: Lack of minimally invasive in-flight laboratory capabilities with limited consumables required for diagnosing identified Exploration Medical Conditions. To mitigate this risk, the availability of inflight laboratory analysis instrumentation has been identified as an essential capability in future exploration missions. Mission architecture poses constraints on equipment and procedures that will be available to treat evidence-based medical conditions according to the Space Medicine Exploration Medical Conditions List (SMEMCL). The SMEMCL provided diagnosis and treatment for the evidence-based medical conditions and hence, a basis for developing ELA functional requirements.

  8. Analytical laboratory quality audits

    SciTech Connect

    Kelley, William D.

    2001-06-11

    Analytical Laboratory Quality Audits are designed to improve laboratory performance. The success of the audit, as for many activities, is based on adequate preparation, precise performance, well documented and insightful reporting, and productive follow-up. Adequate preparation starts with definition of the purpose, scope, and authority for the audit and the primary standards against which the laboratory quality program will be tested. The scope and technical processes involved lead to determining the needed audit team resources. Contact is made with the auditee and a formal audit plan is developed, approved and sent to the auditee laboratory management. Review of the auditee's quality manual, key procedures and historical information during preparation leads to better checklist development and more efficient and effective use of the limited time for data gathering during the audit itself. The audit begins with the opening meeting that sets the stage for the interactions between the audit team and the laboratory staff. Arrangements are worked out for the necessary interviews and examination of processes and records. The information developed during the audit is recorded on the checklists. Laboratory management is kept informed of issues during the audit so there are no surprises at the closing meeting. The audit report documents whether the management control systems are effective. In addition to findings of nonconformance, positive reinforcement of exemplary practices provides balance and fairness. Audit closure begins with receipt and evaluation of proposed corrective actions from the nonconformances identified in the audit report. After corrective actions are accepted, their implementation is verified. Upon closure of the corrective actions, the audit is officially closed.

  9. Underground laboratories in Asia

    SciTech Connect

    Lin, Shin Ted; Yue, Qian

    2015-08-17

    Deep underground laboratories in Asia have been making huge progress recently because underground sites provide unique opportunities to explore the rare-event phenomena for the study of dark matter searches, neutrino physics and nuclear astrophysics as well as the multi-disciplinary researches based on the low radioactive environments. The status and perspectives of Kamioda underground observatories in Japan, the existing Y2L and the planned CUP in Korea, India-based Neutrino Observatory (INO) in India and China JinPing Underground Laboratory (CJPL) in China will be surveyed.

  10. Weekly LiDAR snow depth mapping for operational snow hydrology - the NASA JPL Airborne Snow Observatory (Invited)

    NASA Astrophysics Data System (ADS)

    Deems, J. S.; Painter, T. H.; McGurk, B. J.

    2013-12-01

    Operational hydrologic simulation and forecasting in snowmelt-dominated watersheds currently relies on indices of snow accumulation and melt from measurements at a small number of point locations or geographically-limited manual surveys. These data sources cannot adequately characterize the spatial distribution of snow depth/water equivalent, which is the primary determinant of snowpack volume and runoff rates. The NASA JPL Airborne Snow Observatory's airborne laser scanning system maps snow depth at high spatial and temporal resolutions, providing an unprecedented snowpack monitoring capability and enabling a new operational paradigm. In the Spring of 2013, the ASO mapped snow depth in the Tuolumne River Basin in California's Yosemite National Park on a nominally weekly basis, and provided fast-turnaround spatial snow depth and water equivalent maps to the operators of Hetch Hetchy Reservoir, the water supply for 2.5 million people on the San Francisco peninsula. These products enabled more accurate runoff simulation and optimal reservoir management in a year of very low snow accumulation. We present the initial results from this new application of multi-temporal LiDAR mapping in operational snow hydrology.

  11. Solar Irradiance from GOES Albedo performance in a Hydrologic Model Simulation of Snowmelt Runoff

    NASA Astrophysics Data System (ADS)

    Sumargo, E.; Cayan, D. R.; McGurk, B. J.

    2015-12-01

    In many hydrologic modeling applications, solar radiation has been parameterized using commonly available measures, such as the daily temperature range, due to scarce in situ solar radiation measurement network. However, these parameterized estimates often produce significant biases. Here we test hourly solar irradiance derived from the Geostationary Operational Environmental Satellite (GOES) visible albedo product, using several established algorithms. Focusing on the Sierra Nevada and White Mountain in California, we compared the GOES irradiance and that from a traditional temperature-based algorithm with incoming irradiance from pyranometers at 19 stations. The GOES based estimates yielded 21-27% reduction in root-mean-squared error (average over 19 sites). The derived irradiance is then prescribed as an input to Precipitation-Runoff Modeling System (PRMS). We constrain our experiment to the Tuolumne River watershed and focus our attention on the winter and spring of 1996-2014. A root-mean-squared error reduction of 2-6% in daily inflow to Hetch Hetchy at the lower end of the Tuolumne catchment was achieved by incorporating the insolation estimates at only 8 out of 280 Hydrologic Response Units (HRUs) within the basin. Our ongoing work endeavors to apply satellite-derived irradiance at each individual HRU.

  12. Staggering successes amid controversy in California water management

    NASA Astrophysics Data System (ADS)

    Lund, J. R.

    2012-12-01

    Water in California has always been important and controversial, and it probably always will be. California has a large, growing economy and population in a semi-arid climate. But California's aridity, hydrologic variability, and water controversies have not precluded considerable economic successes. The successes of California's water system have stemmed from the decentralization of water management with historically punctuated periods of more centralized strategic decision-making. Decentralized management has allowed California's water users to efficiently explore incremental solutions to water problems, ranging from early local development of water systems (such as Hetch Hetchy, Owens Valley, and numerous local irrigation projects) to more contemporary efforts at water conservation, water markets, wastewater reuse, and conjunctive use of surface and groundwater. In the cacophony of local and stakeholder interests, strategic decisions have been more difficult, and consequently occur less frequently. California state water projects and Sacramento Valley flood control are examples where decades of effort, crises, floods and droughts were needed to mobilize local interests to agree to major strategic decisions. Currently, the state is faced with making strategic environmental and water management decisions regarding its deteriorating Sacramento-San Joaquin Delta. Not surprisingly, human uncertainties and physical and fiscal non-stationarities dominate this process.

  13. Energy Systems Laboratory Groundbreaking

    SciTech Connect

    Hill, David; Otter, C.L.; Simpson, Mike; Rogers, J.W.

    2011-01-01

    INL recently broke ground for a research facility that will house research programs for bioenergy, advanced battery systems, and new hybrid energy systems that integrate renewable, fossil and nuclear energy sources. Here's video from the groundbreaking ceremony for INL's new Energy Systems Laboratory. You can learn more about CAES research at http://www.facebook.com/idahonationallaboratory.

  14. RUNNING A LANGUAGE LABORATORY.

    ERIC Educational Resources Information Center

    REES, ALUN L.W.

    THIS ARTICLE DESCRIBES THE LANGUAGE LABORATORY AT THE NATIONAL UNIVERSITY OF TRUJILLO AS IT IS USED IN THE FIVE-YEAR ENGLISH TEACHER TRAINING PROGRAM. THE FIRST TWO YEARS OF THIS COURSE ARE INTENSIVE, BASED ON A STUDY OF ENGLISH USING LADO-FRIES MATERIALS (FOR LATIN AMERICAN LEARNERS) WHICH REQUIRE FIVE HOURS OF CLASSWORK A WEEK SUPPLEMENTED BY…

  15. Microcomputers in the Laboratory.

    ERIC Educational Resources Information Center

    Rafert, Bruce; Nicklin, R. C.

    1982-01-01

    A one-semester hour laboratory course introduced junior and senior physics majors to assembly language programing and to interfacing KIM-1 microcomputer to experiments. A general purpose interface to a standard breadboard was developed. Course details, apparatus, and some interfacing projects are given. (Author/SK)

  16. The Applied Mathematics Laboratory.

    ERIC Educational Resources Information Center

    Siegel, Martha J.

    This report describes the Applied Mathematics Laboratory (AML) operated by the Department of Mathematics at Towson State University, Maryland. AML is actually a course offered to selected undergraduates who are given the opportunity to apply their skills in investigating industrial and governmental problems. By agreement with sponsoring…

  17. Simulating Laboratory Procedures.

    ERIC Educational Resources Information Center

    Baker, J. E.; And Others

    1986-01-01

    Describes the use of computer assisted instruction in a medical microbiology course. Presents examples of how computer assisted instruction can present case histories in which the laboratory procedures are simulated. Discusses an authoring system used to prepare computer simulations and provides one example of a case history dealing with fractured…

  18. Green Laboratory Schools.

    ERIC Educational Resources Information Center

    Pope, Jonathan

    1998-01-01

    Presents schools as the perfect microcosms of the world of the 1990s: most work is done indoors, many resources are consumed, and schools sit surrounded by large chunks of land mostly devoted to grass and parking. Suggests that a school can serve as two perfect environmental education laboratories, one indoor and one outdoor. Describes how to…

  19. Aquatic Microbiology Laboratory Manual.

    ERIC Educational Resources Information Center

    Cooper, Robert C.; And Others

    This laboratory manual presents information and techniques dealing with aquatic microbiology as it relates to environmental health science, sanitary engineering, and environmental microbiology. The contents are divided into three categories: (1) ecological and physiological considerations; (2) public health aspects; and (3)microbiology of water…

  20. Introducing Laboratory Safety.

    ERIC Educational Resources Information Center

    DeLorenzo, Ronald

    1985-01-01

    Presents a simple, 10-item quiz designed to make students aware that they must learn laboratory safety. The items include questions on acid/base accidents, several types of fire extinguishers, and safety glassses. Answers and some explanations are included. (DH)

  1. Microgravity Materials Science Laboratory

    NASA Technical Reports Server (NTRS)

    Grisaffe, S. J.

    1985-01-01

    A Microgravity Materials Science Laboratory (MMSL) has been planned, designed, and is being developed. This laboratory will support related efforts to define the requirements for the Microgravity and Materials Processing Laboratory (MMPF) and the MMPF Test Bed for the Space Station. The MMSL will serve as a check out and training facility for science mission specialists for STS, Spacelab and Space Station prior to the full operation of the MMPF Test Bed. The focus of the MMSL will be on experiments related to the understanding of metal/ceramic/glass solidification, high perfection crystal growth and fluid physics. This ground-based laboratory will be used by university/industry/government researchers to examine and become familiar with the potential of new microgravity materials science concepts and to conduct longer term studies aimed at fully developing a l-g understanding of materials and processing phenomena. Such research will help create new high quality concepts for space experiments and will provide the basis for modeling, theories, and hypotheses upon which key space experiments can be defined and developed.

  2. Water Chemistry Laboratory Manual.

    ERIC Educational Resources Information Center

    Jenkins, David; And Others

    This manual of laboratory experiments in water chemistry serves a dual function of illustrating fundamental chemical principles of dilute aqueous systems and of providing the student with some familiarity with the chemical measurements commonly used in water and wastewater analysis. Experiments are grouped in categories on the basis of similar…

  3. Instrumental Analysis Chemistry Laboratory

    ERIC Educational Resources Information Center

    Munoz de la Pena, Arsenio; Gonzalez-Gomez, David; Munoz de la Pena, David; Gomez-Estern, Fabio; Sequedo, Manuel Sanchez

    2013-01-01

    designed for automating the collection and assessment of laboratory exercises is presented. This Web-based system has been extensively used in engineering courses such as control systems, mechanics, and computer programming. Goodle GMS allows the students to submit their results to a…

  4. Introductory Materials Laboratory.

    ERIC Educational Resources Information Center

    Ritter, John E., Jr.

    Described is an introductory materials science laboratory program which emphasizes crystal structure both on the atomistic and microscopic scale and the dependence of materials properties on structure. The content of this program is classified into four major areas: (1) materials science, (2) mechanical behavior of materials, (3) materials testing…

  5. Writing the Laboratory Notebook.

    ERIC Educational Resources Information Center

    Kanare, Howard M.

    The purpose of this book is to teach the principles of proper scientific notekeeping. The principles presented in this book are goals for which working scientists must strive. Chapter 1, "The Reasons for Notekeeping," is an overview of the process of keeping a laboratory notebook. Chapter 2, "The Hardware of Notekeeping," is intended especially…

  6. Energy Systems Laboratory Groundbreaking

    ScienceCinema

    Hill, David; Otter, C.L.; Simpson, Mike; Rogers, J.W.;

    2013-05-28

    INL recently broke ground for a research facility that will house research programs for bioenergy, advanced battery systems, and new hybrid energy systems that integrate renewable, fossil and nuclear energy sources. Here's video from the groundbreaking ceremony for INL's new Energy Systems Laboratory. You can learn more about CAES research at http://www.facebook.com/idahonationallaboratory.

  7. Revitalizing chemistry laboratory instruction

    NASA Astrophysics Data System (ADS)

    McBride, Phil Blake

    This dissertation involves research in three major domains of chemical education as partial fulfillment of the requirements for the Ph.D. program in chemistry at Miami University with a major emphasis on chemical education, and concurrent study in organic chemistry. Unit I, Development and Assessment of a Column Chromatography Laboratory Activity, addresses the domain of Instructional Materials Development and Testing. This unit outlines the process of developing a publishable laboratory activity, testing and revising that activity, and subsequently sharing that activity with the chemical education community. A laboratory activity focusing on the separation of methylene blue and sodium fluorescein was developed to demonstrate the effects of both the stationary and mobile phase in conducting a separation. Unit II, Bringing Industry to the Laboratory, addresses the domain of Curriculum Development and Testing. This unit outlines the development of the Chemistry of Copper Mining module, which is intended for use in high school or undergraduate college chemistry. The module uses the learning cycle approach to present the chemistry of the industrial processes of mining copper to the students. The module includes thirteen investigations (three of which are web-based and ten which are laboratory experiments) and an accompanying interactive CD-ROM, which provides an explanation of the chemistry used in copper mining with a virtual tour of an operational copper mine. Unit III, An Alternative Method of Teaching Chemistry. Integrating Lecture and the Laboratory, is a project that addresses the domain of Research in Student Learning. Fundamental Chemistry was taught at Eastern Arizona College as an integrated lecture/laboratory course that met in two-hour blocks on Monday, Wednesday, and Friday. The students taking this integrated course were compared with students taking the traditional 1-hour lectures held on Monday, Wednesday, and Friday, with accompanying 3-hour lab on

  8. Laboratory Waste Management. A Guidebook.

    ERIC Educational Resources Information Center

    American Chemical Society, Washington, DC.

    A primary goal of the American Chemical Society Task Force on Laboratory Waste Management is to provide laboratories with the information necessary to develop effective strategies and training programs for managing laboratory wastes. This book is intended to present a fresh look at waste management from the laboratory perspective, considering both…

  9. Smart Grid Integration Laboratory

    SciTech Connect

    Troxell, Wade

    2011-12-22

    The initial federal funding for the Colorado State University Smart Grid Integration Laboratory is through a Congressionally Directed Project (CDP), DE-OE0000070 Smart Grid Integration Laboratory. The original program requested in three one-year increments for staff acquisition, curriculum development, and instrumentation all which will benefit the Laboratory. This report focuses on the initial phase of staff acquisition which was directed and administered by DOE NETL/ West Virginia under Project Officer Tom George. Using this CDP funding, we have developed the leadership and intellectual capacity for the SGIC. This was accomplished by investing (hiring) a core team of Smart Grid Systems engineering faculty focused on education, research, and innovation of a secure and smart grid infrastructure. The Smart Grid Integration Laboratory will be housed with the separately funded Integrid Laboratory as part of CSU's overall Smart Grid Integration Center (SGIC). The period of performance of this grant was 10/1/2009 to 9/30/2011 which included one no cost extension due to time delays in faculty hiring. The Smart Grid Integration Laboratory's focus is to build foundations to help graduate and undergraduates acquire systems engineering knowledge; conduct innovative research; and team externally with grid smart organizations. Using the results of the separately funded Smart Grid Workforce Education Workshop (May 2009) sponsored by the City of Fort Collins, Northern Colorado Clean Energy Cluster, Colorado State University Continuing Education, Spirae, and Siemens has been used to guide the hiring of faculty, program curriculum and education plan. This project develops faculty leaders with the intellectual capacity to inspire its students to become leaders that substantially contribute to the development and maintenance of Smart Grid infrastructure through topics such as: (1) Distributed energy systems modeling and control; (2) Energy and power conversion; (3) Simulation of

  10. Procedures of Exercise Physiology Laboratories

    NASA Technical Reports Server (NTRS)

    Bishop, Phillip A.; Fortney, Suzanne; Greenisen, Michael; Siconolfi, Steven F.; Bamman, Marcas M.; Moore, Alan D., Jr.; Squires, William

    1998-01-01

    This manual describes the laboratory methods used to collect flight crew physiological performance data at the Johnson Space Center. The Exercise Countermeasures Project Laboratory is a standard physiology laboratory; only the application to the study of human physiological adaptations to spaceflight is unique. In the absence of any other recently published laboratory manual, this manual should be a useful document staffs and students of other laboratories.

  11. The Indiana Laboratory System: Focus on Environmental Laboratories

    PubMed Central

    Hammes, Kara R.; Matheson, Shelley R.; Lovchik, Judith C.

    2013-01-01

    The Indiana State Department of Health (ISDH) Laboratories are working to improve Indiana's state public health laboratory system. Environmental laboratories are key stakeholders in this system, but their needs have been largely unaddressed prior to this project. In an effort to identify and engage these laboratories, the ISDH Laboratories organized and hosted the First Annual Environmental Laboratories Meeting. The focus of this meeting was on water-testing laboratories throughout the state. Meeting objectives included issue identification, disaster recovery response, and communication efforts among system partners. Common concerns included the need for new technology and updated methods, analyst training, certification programs for analysts and sample collectors, electronic reporting, and regulation interpretation and inspection consistency. Now that these issues have been identified, they can be addressed through a combination of laboratory workgroups and collaboration with Indiana's regulatory agencies. Participants were overwhelmingly positive about the meeting's outcomes and were willing to help with future laboratory system improvement projects. PMID:23997304

  12. Space Radiation Effects Laboratory

    NASA Technical Reports Server (NTRS)

    1969-01-01

    The SREL User's Handbook is designed to provide information needed by those who plan experiments involving the accelerators at this laboratory. Thus the Handbook will contain information on the properties of the machines, the beam parameters, the facilities and services provided for experimenters, etc. This information will be brought up to date as new equipment is added and modifications accomplished. This Handbook is influenced by the many excellent models prepared at other accelerator laboratories. In particular, the CERN Synchrocyclotron User's Handbook (November 1967) is closely followed in some sections, since the SREL Synchrocyclotron is a duplicate of the CERN machine. We wish to thank Dr. E. G. Michaelis for permission to draw so heavily on his work, particularly in Section II of this Handbook. We hope that the Handbook will prove useful, and will welcome suggestions and criticism.

  13. Laboratory Evaluation of Anemia

    PubMed Central

    Wallerstein, Ralph O.

    1987-01-01

    The laboratory evaluation of anemia begins with a complete blood count and reticulocyte count. The anemia is then categorized as microcytic, macrocytic or normocytic, with or without reticulocytosis. Examination of the peripheral smear and a small number of specific tests confirm the diagnosis. The serum iron level, total iron-binding capacity, serum ferritin level and hemoglobin electrophoresis generally separate the microcytic anemias. The erythrocyte size-distribution width may be particularly helpful in distinguishing iron deficiency from thalassemia minor. Significant changes have occurred in the laboratory evaluation of macrocytic anemia, and a new syndrome of nitrous oxide-induced megaloblastosis and neurologic dysfunction has been recognized. A suggested approach to the hemolytic anemias includes using the micro-Coombs' test and ektacytometry. Finally, a number of causes have been identified for normocytic anemia without reticulocytosis, including normocytic megaloblastic anemia and the acquired immunodeficiency syndrome. PMID:3577135

  14. Laboratory models of tornadoes

    NASA Astrophysics Data System (ADS)

    Church, Christopher R.; Snow, John T.

    Nature provides many examples of intense but small-scale atmospheric vortices, the most devastating being tornadoes. Other small vortices include waterspouts, fire whirls, dust devils, and steam devils. Several aspects of small-scale atmospheric vortex flows are of concern to the atmospheric scientist, namely: determination of their kinematic structure, understanding of their formation and dynamics, identification of the factors that control their intensities, and application of new knowledge and insights in ways that will provide greater protection for society from the hazards of these phenomena. Although some of the vortex types listed above occur more frequently and are more readily available for observation than tornadoes, all small-scale vortices are inherently infrequent, short-lived phenomena; it has been expedient for some scientists to simulate tornadolike flows in the laboratory. This laboratory work constitutes a small but significant part of the overall tornado research effort.

  15. A lunar laboratory

    NASA Technical Reports Server (NTRS)

    Keaton, P. W.; Duke, M. B.

    1987-01-01

    An international research laboratory can be established on the Moon in the early years of the 21st Century. It can be built using the transportation system now envisioned by NASA, which includes a space station for Earth orbital logistics and orbital transfer vehicles for Earth-Moon transportation. A scientific laboratory on the Moon would permit extended surface and subsurface geological exploration; long-duration experiments defining the lunar environment and its modification by surface activity; new classes of observations in astronomy; space plasma and fundamental physics experiments; and lunar resource development. The discovery of a lunar source for propellants may reduce the cost of constructing large permanent facilities in space and enhance other space programs such as Mars exploration.

  16. Remote Sensing Laboratory - RSL

    ScienceCinema

    None

    2015-01-09

    One of the primary resources supporting homeland security is the Remote Sensing Laboratory, or RSL. The Laboratory creates advanced technologies for emergency response operations, radiological incident response, and other remote sensing activities. RSL emergency response teams are on call 24-hours a day, and maintain the capability to deploy domestically and internationally in response to threats involving the loss, theft, or release of nuclear or radioactive material. Such incidents might include Nuclear Power Plant accidents, terrorist incidents involving nuclear or radiological materials, NASA launches, and transportation accidents involving nuclear materials. Working with the US Department of Homeland Security, RSL personnel equip, maintain, and conduct training on the mobile detection deployment unit, to provide nuclear radiological security at major national events such as the super bowl, the Indianapolis 500, New Year's Eve celebrations, presidential inaugurations, international meetings and conferences, just about any event where large numbers of people will gather.

  17. Remote Sensing Laboratory - RSL

    SciTech Connect

    2014-11-06

    One of the primary resources supporting homeland security is the Remote Sensing Laboratory, or RSL. The Laboratory creates advanced technologies for emergency response operations, radiological incident response, and other remote sensing activities. RSL emergency response teams are on call 24-hours a day, and maintain the capability to deploy domestically and internationally in response to threats involving the loss, theft, or release of nuclear or radioactive material. Such incidents might include Nuclear Power Plant accidents, terrorist incidents involving nuclear or radiological materials, NASA launches, and transportation accidents involving nuclear materials. Working with the US Department of Homeland Security, RSL personnel equip, maintain, and conduct training on the mobile detection deployment unit, to provide nuclear radiological security at major national events such as the super bowl, the Indianapolis 500, New Year's Eve celebrations, presidential inaugurations, international meetings and conferences, just about any event where large numbers of people will gather.

  18. Automated Microbial Metabolism Laboratory

    NASA Technical Reports Server (NTRS)

    1973-01-01

    Development of the automated microbial metabolism laboratory (AMML) concept is reported. The focus of effort of AMML was on the advanced labeled release experiment. Labeled substrates, inhibitors, and temperatures were investigated to establish a comparative biochemical profile. Profiles at three time intervals on soil and pure cultures of bacteria isolated from soil were prepared to establish a complete library. The development of a strategy for the return of a soil sample from Mars is also reported.

  19. Portable Laser Laboratory

    SciTech Connect

    Weir, J.T.

    1994-07-01

    A Portable Laser Laboratory (PLL) is being designed and built for the CALIOPE Program tests which will begin in October of 1994. The PLL is designed to give maximum flexibility for evolving laser experiments and can be readily moved by loading it onto a standard truck trailer. The internal configuration for the October experiments will support a two line DIAL system running in the mid-IR. Brief descriptions of the laser and detection systems are included.

  20. Hanford cultural resources laboratory

    SciTech Connect

    Wright, M.K.

    1995-06-01

    This section of the 1994 Hanford Site Environmental Report describes activities of the Hanford Cultural Resources Laboratory (HCRL) which was established by the Richland Operations Office in 1987 as part of PNL.The HCRL provides support for the management of the archaeological, historical, and traditional cultural resources of the site in a manner consistent with the National Historic Preservation Act, the Native American Graves Protection and Repatriation Act, and the American Indian Religious Freedom Act.

  1. Princeton Plasma Physics Laboratory:

    SciTech Connect

    Phillips, C.A.

    1986-01-01

    This paper discusses progress on experiments at the Princeton Plasma Physics Laboratory. The projects and areas discussed are: Principal Parameters Achieved in Experimental Devices, Tokamak Fusion Test Reactor, Princeton Large Torus, Princeton Beta Experiment, S-1 Spheromak, Current-Drive Experiment, X-ray Laser Studies, Theoretical Division, Tokamak Modeling, Spacecraft Glow Experiment, Compact Ignition Tokamak, Engineering Department, Project Planning and Safety Office, Quality Assurance and Reliability, and Administrative Operations.

  2. Laboratory Astrochemistry: Interstellar PAHs

    NASA Technical Reports Server (NTRS)

    Salama, Farid; DeVincenzi, Donald L. (Technical Monitor)

    2000-01-01

    Polycyclic aromatic hydrocarbons (PAHs) are now considered to be an important and ubiquitous component of the organic material in space. PAHs are found in a large variety of extraterrestrial materials such as interplanetary dust particles (IDPs) and meteoritic materials. PAHs are also good candidates to account for the infrared emission bands (UIRs) and the diffuse interstellar optical absorption bands (DIBs) detected in various regions of the interstellar medium. The recent observations made with the Infrared Space Observatory (ISO) have confirmed the ubiquitous nature of the UIR bands and their carriers. PAHs are thought to form through chemical reactions in the outflow from carbon-rich stars in a process similar to soot formation. Once injected in the interstellar medium, PAHs are further processed by the interstellar radiation field, interstellar shocks and energetic particles. A major, dedicated, laboratory effort has been undertaken to measure the physical and chemical characteristics of these complex molecules and their ions under experimental conditions that mimic the interstellar conditions. These measurements require collision-free conditions where the molecules and ions are cold and chemically isolated. The spectroscopy of PAHs under controlled conditions represents an essential diagnostic tool to study the evolution of extraterrestrial PAHs. The Astrochemistry Laboratory program will be discussed through its multiple aspects: (1) objectives, (2) approach and techniques adopted, (3) adaptability to the nature of the problem(s), and (4) results and implications for astronomy as well as for molecular spectroscopy. A review of the data generated through laboratory simulations of space environments and the role these data have played in our current understanding of the properties of interstellar PAHs will be presented. The discussion will also introduce the newest generation of laboratory experiments that are currently being developed in order to provide a

  3. The flight robotics laboratory

    NASA Technical Reports Server (NTRS)

    Tobbe, Patrick A.; Williamson, Marlin J.; Glaese, John R.

    1988-01-01

    The Flight Robotics Laboratory of the Marshall Space Flight Center is described in detail. This facility, containing an eight degree of freedom manipulator, precision air bearing floor, teleoperated motion base, reconfigurable operator's console, and VAX 11/750 computer system, provides simulation capability to study human/system interactions of remote systems. The facility hardware, software and subsequent integration of these components into a real time man-in-the-loop simulation for the evaluation of spacecraft contact proximity and dynamics are described.

  4. Laboratory Diagnosis of Amebiasis

    PubMed Central

    Tanyuksel, Mehmet; Petri, William A.

    2003-01-01

    The detection of Entamoeba histolytica, the causative agent of amebiasis, is an important goal of the clinical microbiology laboratory. To assess the scope of E. histolytica infection, it is necessary to utilize accurate diagnostic tools. As more is discovered about the molecular and cell biology of E. histolytica, there is great potential for further understanding the pathogenesis of amebiasis. Molecular biology-based diagnosis may become the technique of choice in the future because establishment of these protozoa in culture is still not a routine clinical laboratory process. In all cases, combination of serologic tests with detection of the parasite (by antigen detection or PCR) offers the best approach to diagnosis, while PCR techniques remain impractical in many developing country settings. The detection of amebic markers in serum in patients with amebic colitis and liver abscess appears promising but is still only a research tool. On the other hand, stool antigen detection tests offer a practical, sensitive, and specific way for the clinical laboratory to detect intestinal E. histolytica. All the current tests suffer from the fact that the antigens detected are denatured by fixation of the stool specimen, limiting testing to fresh or frozen samples. PMID:14557296

  5. Laboratory microfusion capability study

    NASA Astrophysics Data System (ADS)

    1993-05-01

    The purpose of this study is to elucidate the issues involved in developing a Laboratory Microfusion Capability (LMC) which is the major objective of the Inertial Confinement Fusion (ICF) program within the purview of the Department of Energy's Defense Programs. The study was initiated to support a number of DOE management needs: to provide insight for the evolution of the ICF program; to afford guidance to the ICF laboratories in planning their research and development programs; to inform Congress and others of the details and implications of the LMC; to identify criteria for selection of a concept for the Laboratory Microfusion Facility; and to develop a coordinated plan for the realization of an LMC. As originally proposed, the LMC study was divided into two phases. The first phase identifies the purpose and potential utility of the LMC, the regime of its performance parameters, driver independent design issues and requirements, its development goals and requirements, and associated technical, management, staffing, environmental, and other developmental and operational issues. The second phase addresses driver-dependent issues such as specific design, range of performance capabilities, and cost. The study includes four driver options: the neodymium-glass solid state laser, the krypton fluoride excimer gas laser, the light-ion accelerator, and the heavy-ion induction linear accelerator. The results of the Phase 2 study are described in the present report.

  6. Exploration Laboratory Analysis

    NASA Technical Reports Server (NTRS)

    Krihak, M.; Ronzano, K.; Shaw, T.

    2016-01-01

    The Exploration Laboratory Analysis (ELA) project supports the Exploration Medical Capability (ExMC) risk to minimize or reduce the risk of adverse health outcomes and decrements in performance due to in-flight medical capabilities on human exploration missions. To mitigate this risk, the availability of inflight laboratory analysis instrumentation has been identified as an essential capability for manned exploration missions. Since a single, compact space-ready laboratory analysis capability to perform all exploration clinical measurements is not commercially available, the ELA project objective is to demonstrate the feasibility of emerging operational and analytical capability as a biomedical diagnostics precursor to long duration manned exploration missions. The initial step towards ground and flight demonstrations in fiscal year (FY) 2015 was the down selection of platform technologies for demonstrations in the space environment. The technologies selected included two Small Business Innovation Research (SBIR) performers: DNA Medicine Institutes rHEALTH X and Intelligent Optical Systems later flow assays combined with Holomics smartphone analyzer. The selection of these technologies were based on their compact size, breadth of analytical capability and favorable ability to process fluids in a space environment, among several factors. These two technologies will be advanced to meet ground and flight demonstration success criteria and requirements that will be finalized in FY16. Also, the down selected performers will continue the technology development phase towards meeting prototype deliverables in either late 2016 or 2017.

  7. High Resolution Laboratory Spectroscopy

    NASA Astrophysics Data System (ADS)

    Brünken, S.; Schlemmer, S.

    2016-05-01

    In this short review we will highlight some of the recent advancements in the field of high-resolution laboratory spectroscopy that meet the needs dictated by the advent of highly sensitive and broadband telescopes like ALMA and SOFIA. Among these is the development of broadband techniques for the study of complex organic molecules, like fast scanning conventional absorption spectroscopy based on multiplier chains, chirped pulse instrumentation, or the use of synchrotron facilities. Of similar importance is the extension of the accessible frequency range to THz frequencies, where many light hydrides have their ground state rotational transitions. Another key experimental challenge is the production of sufficiently high number densities of refractory and transient species in the laboratory, where discharges have proven to be efficient sources that can also be coupled to molecular jets. For ionic molecular species sensitive action spectroscopic schemes have recently been developed to overcome some of the limitations of conventional absorption spectroscopy. Throughout this review examples demonstrating the strong interplay between laboratory and observational studies will be given.

  8. Cysticercosis in laboratory rabbits.

    PubMed

    Owiny, J R

    2001-03-01

    There are no data on the current incidence of Taenia pisiformis in laboratory rabbits. Two cases of cysticercosis most likely due to T. pisiformis in laboratory rabbits (intermediate host) are presented. Both rabbits had no contact with dogs (final host); their caretakers did not work with dogs, and these caretakers changed into facility scrubs and wore gloves when working with the rabbits. Rabbit 1 may have been infected after being fed hay at our facility. In light of the life cycle of the parasite and the history of rabbit 2, it potentially could have been infected prior to arrival at our facility. There have been only three cases of tapeworm cysts in rabbits in our facility (average daily census, 250) during the last 10 years (incidence, < 1%). This report indicates that although cysticercosis is rare in laboratory rabbits, one should always be aware of such incidental findings. Although it may not produce overt illness in the rabbit, hepatic migration could adversely affect the outcome of some experimental procedures PMID:11300689

  9. Economic Education Laboratory: Initiating a Meaningful Economic Learning through Laboratory

    ERIC Educational Resources Information Center

    Noviani, Leny; Soetjipto, Budi Eko; Sabandi, Muhammad

    2015-01-01

    Laboratory is considered as one of the resources in supporting the learning process. The laboratory can be used as facilities to deepen the concepts, learning methods and enriching students' knowledge and skills. Learning process by utilizing the laboratory facilities can help lecturers and students in grasping the concept easily, constructing the…

  10. Manufacturing Laboratory (Fact Sheet)

    SciTech Connect

    Not Available

    2011-10-01

    This fact sheet describes the purpose, lab specifications, applications scenarios, and information on how to partner with NREL's Manufacturing Laboratory at the Energy Systems Integration Facility. The Manufacturing Laboratory at NREL's Energy Systems Integration Facility (ESIF) focuses on developing methods and technologies that will assist manufacturers of hydrogen and fuel cell technologies, as well as other renewable energy technologies, to scale up their manufacturing capabilities to volumes that meet DOE and industry targets. Specifically, the manufacturing activity is currently focused on developing and validating quality control techniques to assist manufacturers of low temperature and high temperature fuel cells in the transition from low to high volume production methods for cells and stacks. Capabilities include initial proof-of-concept studies through prototype system development and in-line validation. Existing diagnostic capabilities address a wide range of materials, including polymer films, carbon and catalyst coatings, carbon fiber papers and wovens, and multi-layer assemblies of these materials, as well as ceramic-based materials in pre- or post-fired forms. Work leading to the development of non-contact, non-destructive techniques to measure critical dimensional and functional properties of fuel cell and other materials, and validation of those techniques on the continuous processing line. This work will be supported by materials provided by our partners. Looking forward, the equipment in the laboratory is set up to be modified and extended to provide processing capabilities such as coating, casting, and deposition of functional layers, as well as associated processes such as drying or curing. In addition, continuous processes are used for components of organic and thin film photovoltaics (PV) as well as battery technologies, so synergies with these important areas will be explored.

  11. Purdue Hydrogen Systems Laboratory

    SciTech Connect

    Jay P Gore; Robert Kramer; Timothee L Pourpoint; P. V. Ramachandran; Arvind Varma; Yuan Zheng

    2011-12-28

    The Hydrogen Systems Laboratory in a unique partnership between Purdue University's main campus in West Lafayette and the Calumet campus was established and its capabilities were enhanced towards technology demonstrators. The laboratory engaged in basic research in hydrogen production and storage and initiated engineering systems research with performance goals established as per the USDOE Hydrogen, Fuel Cells, and Infrastructure Technologies Program. In the chemical storage and recycling part of the project, we worked towards maximum recycling yield via novel chemical selection and novel recycling pathways. With the basic potential of a large hydrogen yield from AB, we used it as an example chemical but have also discovered its limitations. Further, we discovered alternate storage chemicals that appear to have advantages over AB. We improved the slurry hydrolysis approach by using advanced slurry/solution mixing techniques. We demonstrated vehicle scale aqueous and non-aqueous slurry reactors to address various engineering issues in on-board chemical hydrogen storage systems. We measured the thermal properties of raw and spent AB. Further, we conducted experiments to determine reaction mechanisms and kinetics of hydrothermolysis in hydride-rich solutions and slurries. We also developed a continuous flow reactor and a laboratory scale fuel cell power generation system. The biological hydrogen production work summarized as Task 4.0 below, included investigating optimal hydrogen production cultures for different substrates, reducing the water content in the substrate, and integrating results from vacuum tube solar collector based pre and post processing tests into an enhanced energy system model. An automated testing device was used to finalize optimal hydrogen production conditions using statistical procedures. A 3 L commercial fermentor (New Brunswick, BioFlo 115) was used to finalize testing of larger samples and to consider issues related to scale up. Efforts

  12. Laboratory for Extraterrestrial Physics

    NASA Technical Reports Server (NTRS)

    Vondrak, Richard R. (Technical Monitor)

    2001-01-01

    The NASA Goddard Space Flight Center (GSFC) Laboratory for Extraterrestrial Physics (LEP) performs experimental and theoretical research on the heliosphere, the interstellar medium, and the magnetospheres and upper atmospheres of the planets, including Earth. LEP space scientists investigate the structure and dynamics of the magnetospheres of the planets including Earth. Their research programs encompass the magnetic fields intrinsic to many planetary bodies as well as their charged-particle environments and plasma-wave emissions. The LEP also conducts research into the nature of planetary ionospheres and their coupling to both the upper atmospheres and their magnetospheres. Finally, the LEP carries out a broad-based research program in heliospheric physics covering the origins of the solar wind, its propagation outward through the solar system all the way to its termination where it encounters the local interstellar medium. Special emphasis is placed on the study of solar coronal mass ejections (CME's), shock waves, and the structure and properties of the fast and slow solar wind. LEP planetary scientists study the chemistry and physics of planetary stratospheres and tropospheres and of solar system bodies including meteorites, asteroids, comets, and planets. The LEP conducts a focused program in astronomy, particularly in the infrared and in short as well as very long radio wavelengths. We also perform an extensive program of laboratory research, including spectroscopy and physical chemistry related to astronomical objects. The Laboratory proposes, develops, fabricates, and integrates experiments on Earth-orbiting, planetary, and heliospheric spacecraft to measure the characteristics of planetary atmospheres and magnetic fields, and electromagnetic fields and plasmas in space. We design and develop spectrometric instrumentation for continuum and spectral line observations in the x-ray, gamma-ray, infrared, and radio regimes; these are flown on spacecraft to study

  13. Princeton Plasma Physics Laboratory

    SciTech Connect

    Not Available

    1990-01-01

    This report discusses the following topics: principal parameters achieved in experimental devices fiscal year 1990; tokamak fusion test reactor; compact ignition tokamak; Princeton beta experiment- modification; current drive experiment-upgrade; international collaboration; x-ray laser studies; spacecraft glow experiment; plasma processing: deposition and etching of thin films; theoretical studies; tokamak modeling; international thermonuclear experimental reactor; engineering department; project planning and safety office; quality assurance and reliability; technology transfer; administrative operations; PPPL patent invention disclosures for fiscal year 1990; graduate education; plasma physics; graduate education: plasma science and technology; science education program; and Princeton Plasma Physics Laboratory reports fiscal year 1990.

  14. Novae as Thermonuclear Laboratories

    NASA Astrophysics Data System (ADS)

    Clayton, D. D.

    2003-07-01

    Fred Hoyle undertook a study of observational consequences of the thermonuclear paradigm for the nova event in the years following his 1972 resignation from Cambridge University. The most fruitful of these have been in the areas of gamma-ray astronomy, by which one attempts to measure the level of radioactivity in the nova envelope, and of presolar grain studies in laboratories, by which one measures anomalous isotopic ratios that fingerprint condensation in the thermonuclear event. This work summarizes progress with these two astronomical measures of the novae.

  15. Materials Science Laboratory

    NASA Technical Reports Server (NTRS)

    Jackson, Dionne

    2005-01-01

    The NASA Materials Science Laboratory (MSL) provides science and engineering services to NASA and Contractor customers at KSC, including those working for the Space Shuttle. International Space Station. and Launch Services Programs. These services include: (1) Independent/unbiased failure analysis (2) Support to Accident/Mishap Investigation Boards (3) Materials testing and evaluation (4) Materials and Processes (M&P) engineering consultation (5) Metrology (6) Chemical analysis (including ID of unknown materials) (7) Mechanical design and fabrication We provide unique solutions to unusual and urgent problems associated with aerospace flight hardware, ground support equipment and related facilities.

  16. Gait Analysis Laboratory

    NASA Technical Reports Server (NTRS)

    1976-01-01

    Complete motion analysis laboratory has evolved out of analyzing walking patterns of crippled children at Stanford Children's Hospital. Data is collected by placing tiny electrical sensors over muscle groups of child's legs and inserting step-sensing switches in soles of shoes. Miniature radio transmitters send signals to receiver for continuous recording of abnormal walking pattern. Engineers are working to apply space electronics miniaturization techniques to reduce size and weight of telemetry system further as well as striving to increase signal bandwidth so analysis can be performed faster and more accurately using a mini-computer.

  17. Laboratory and Industrial Ventilation

    NASA Technical Reports Server (NTRS)

    1972-01-01

    This handbook supplements the Facilities Engineering Handbook (NHB 7320.1) and provides additional policies and criteria for uniform application to ventilation systems. It expands basic requirements, provides additional design and construction guidance, and places emphasis on those design considerations which will provide for greater effectiveness in the use of these systems. The provisions of this handbook are applicable to all NASA field installations and the Jet Propulsion Laboratory. Since supply of this handbook is limited, abstracts of the portion or portions applicable to a given requirement will be made for the individual specific needs encountered rather than supplying copies of the handbook as has been past practice.

  18. Preoperative Laboratory Testing.

    PubMed

    Bock, Matthias; Fritsch, Gerhard; Hepner, David L

    2016-03-01

    Routine preoperative testing is not cost-effective, because it is unlikely to identify significant abnormalities. Abnormal findings from routine testing are more likely to be false positive, are costly to pursue, introduce a new risk, increase the patient's anxiety, and are inconvenient to the patient. Abnormal findings rarely alter the surgical or anesthetic plan, and there is usually no association between perioperative complications and abnormal laboratory results. Incidental findings and false positive results may lead to increased hospital visits and admissions. Preoperative testing needs to be done based on a targeted history and physical examination and the type of surgery. PMID:26927738

  19. Laboratory prototype flash evaporator

    NASA Technical Reports Server (NTRS)

    Gaddis, J. L.

    1972-01-01

    A laboratory prototype flash evaporator that is being developed as a candidate for the space shuttle environmental control system expendable heat sink is described. The single evaporator configuration uses water as an evaporant to accommodate reentry and on-orbit peak heat loads, and Freon 22 for terrestrial flight phases below 120,000 feet altitude. The design features, fabrication techniques used for the prototype unit, redundancy considerations, and the fluid temperature control arrangement are reported in detail. The results of an extensive test program to determine the evaporator operational characteristics under a wide variety of conditions are presented.

  20. The Laboratory in Professional Education.

    ERIC Educational Resources Information Center

    Kaplan, Harold N.

    1979-01-01

    The role of laboratory experience in professional education is discussed. Although laboratory experiments are often expensive and demanding on faculty time, they can offer a unique experience to the veterinary medicine student. (BH)

  1. How Reliable Is Laboratory Testing?

    MedlinePlus

    ... to day in a laboratory. The other two, sensitivity and specificity, deal with how well the test ... are frequently monitored by the professional laboratory personnel. Sensitivity and specificity data are determined by research studies ...

  2. EPA LABORATORIES IMPLEMENT EMS PROGRAM

    EPA Science Inventory

    This paper highlights the breadth and magnitude of carrying out an effective Environmental Management System (EMS) program at the U.S. EPA's research and development laboratories. Federal research laboratories have unique operating challenges compared to more centralized industr...

  3. Tethered gravity laboratories study

    NASA Technical Reports Server (NTRS)

    Lucchetti, F.

    1990-01-01

    The scope of the study is to investigate ways of controlling the microgravity environment of the International Space Station by means of a tethered system. Four main study tasks were performed. First, researchers analyzed the utilization of the tether systems to improve the lowest possible steady gravity level on the Space Station and the tether capability to actively control the center of gravity position in order to compensate for activities that would upset the mass distribution of the Station. The purpose of the second task was to evaluate the whole of the experiments performable in a variable gravity environment and the related beneficial residual accelerations, both for pure and applied research in the fields of fluid, materials, and life science, so as to assess the relevance of a variable g-level laboratory. The third task involves the Tethered Variable Gravity Laboratory. The use of the facility that would crawl along a deployed tether and expose experiments to varying intensities of reduced gravity is discussed. Last, a study performed on the Attitude Tether Stabilizer concept is discussed. The stabilization effect of ballast masses tethered to the Space Station was investigated as a means of assisting the attitude control system of the Station.

  4. Mobile Energy Laboratory Procedures

    SciTech Connect

    Armstrong, P.R.; Batishko, C.R.; Dittmer, A.L.; Hadley, D.L.; Stoops, J.L.

    1993-09-01

    Pacific Northwest Laboratory (PNL) has been tasked to plan and implement a framework for measuring and analyzing the efficiency of on-site energy conversion, distribution, and end-use application on federal facilities as part of its overall technical support to the US Department of Energy (DOE) Federal Energy Management Program (FEMP). The Mobile Energy Laboratory (MEL) Procedures establish guidelines for specific activities performed by PNL staff. PNL provided sophisticated energy monitoring, auditing, and analysis equipment for on-site evaluation of energy use efficiency. Specially trained engineers and technicians were provided to conduct tests in a safe and efficient manner with the assistance of host facility staff and contractors. Reports were produced to describe test procedures, results, and suggested courses of action. These reports may be used to justify changes in operating procedures, maintenance efforts, system designs, or energy-using equipment. The MEL capabilities can subsequently be used to assess the results of energy conservation projects. These procedures recognize the need for centralized NM administration, test procedure development, operator training, and technical oversight. This need is evidenced by increasing requests fbr MEL use and the economies available by having trained, full-time MEL operators and near continuous MEL operation. DOE will assign new equipment and upgrade existing equipment as new capabilities are developed. The equipment and trained technicians will be made available to federal agencies that provide funding for the direct costs associated with MEL use.

  5. Microgravity Emissions Laboratory Developed

    NASA Technical Reports Server (NTRS)

    Goodnight, Thomas W.; McNelis, Anne M.

    2001-01-01

    The Microgravity Emissions Laboratory (MEL) was developed for the support, simulation, and verification of the International Space Station microgravity environment. The MEL utilizes an inertial measurement system using acceleration emissions generated by various operating components of the space station. These emissions, if too large, could hinder the science performed on the space station by disturbing the microgravity environment. Typical test components are disk drives, pumps, motors, solenoids, fans, and cameras. These components will produce inertial forces, which disturb the microgravity on-orbit station environment. These components, usually housed within a station rack, must meet acceleration limits imposed at the rack interface for minimizing the onboard station-operating environment. The NASA Glenn Research Center developed this one-of-a-kind laboratory for testing components and, eventually, rack-level configurations. The MEL approach is to measure the component's generated inertial forces. This force is a product of the full diagonal mass matrix including the test setup (the center of gravity, mass moment of inertia, and weight) and the resolved diagonal rigid-body acceleration determined from measurements using the 10 apparatus accelerometers. The mass matrix can be test derived. The bifilar torsional pendulum method is used to measure the moment of inertia for the test component.

  6. Chemistry laboratory safety manual available

    NASA Technical Reports Server (NTRS)

    Elsbrock, R. G.

    1968-01-01

    Chemistry laboratory safety manual outlines safe practices for handling hazardous chemicals and chemistry laboratory equipment. Included are discussions of chemical hazards relating to fire, health, explosion, safety equipment and procedures for certain laboratory techniques and manipulations involving glassware, vacuum equipment, acids, bases, and volatile solvents.

  7. Managing the Occupational Education Laboratory.

    ERIC Educational Resources Information Center

    Storm, George

    This guide for occupational educators deals with laboratory and instructional management on an interdisciplinary basis within the broad field of occupational education. The principles discussed are intended to be applied at all levels and in all types of laboratories. The text suggests effective ways of organizing laboratories so that students can…

  8. Introductory Archaeology: The Inexpensive Laboratory.

    ERIC Educational Resources Information Center

    Rice, Patricia C.

    1990-01-01

    Describes a number of student-focused laboratory exercises that are inexpensive, yet show the scientific character of archaeology. Describes the environmental laboratory exercise which includes the following analysis topics: (1) pollen; (2) earth core; (3) microfaunal; and (4) microwear. Describes the ceramic laboratory which involves…

  9. Diversifying the Introductory Physics Laboratory.

    ERIC Educational Resources Information Center

    Jewett, John W., Jr.; Lessie, Douglas

    1983-01-01

    Describes a two-semester laboratory program designed to motivate students. The program consists of computer-oriented modules and discovery approach laboratory exercises. Students complete similar computer/laboratory material during the first semester but elect one of three tracks during the second semester (computer, every-day life, and…

  10. Federal Laboratory Consortium Resource Directory.

    ERIC Educational Resources Information Center

    Federal Laboratory Consortium, Washington, DC.

    Intended to assist both the private and public sectors to locate and utilize technological expertise within the federal laboratories, this directory lists the federal laboratories and centers that are affiliated with the Federal Laboratory Consortium and describes the area of technological expertise they can make available to solve problems. This…

  11. Laboratory Materials: Affordances or Constraints?

    ERIC Educational Resources Information Center

    Jordan, Rebecca C.; Ruibal-Villasenor, Maria; Hmelo-Silver, Cindy E.; Etkina, Eugenia

    2011-01-01

    Laboratory instruction is critical to the understanding of biology and is a central piece of biological sciences instruction. Although much investigation has focused on the content of biology laboratory exercises, we contend that understanding the extent to which the laboratory materials can aid or limit experimental investigation is of equal…

  12. Computer integrated laboratory testing

    NASA Technical Reports Server (NTRS)

    Dahl, Charles C.

    1992-01-01

    The objective is the integration of computers into the Engineering Materials Science Laboratory course, where existing test equipment is not computerized. The first lab procedure is to demonstrate and produce a material phase change curve. The second procedure is a demonstration of the modulus of elasticity and related stress-strain curve, plastic performance, maximum and failure strength. The process of recording data by sensors that are connected to a data logger which adds a time base, and the data logger in turn connected to a computer, places the materials labs into a computer integrated mode with minimum expense and maximum flexibility. The sensor signals are input into a spread sheet for tabular records, curve generation, and graph printing.

  13. First International Microgravity Laboratory

    NASA Astrophysics Data System (ADS)

    McMahan, Tracy; Shea, Charlotte; Wiginton, Margaret; Neal, Valerie; Gately, Michele; Hunt, Lila; Graben, Jean; Tiderman, Julie; Accardi, Denise

    This colorful booklet presents capsule information on every aspect of the International Microgravity Laboratory (IML). As part of Spacelab, IML is divided into Life Science Experiments and Materials Science Experiments. Because the life and materials sciences use different Spacelab resources, they are logically paired on the IML missions. Life science investigations generally require significant crew involvement, and crew members often participate as test subjects or operators. Materials missions capitalize on these complementary experiments. International cooperation consists in participation by the European Space Agency, Canada, France, Germany, and Japan who are all partners in developing hardware and experiments of IML missions. IML experiments are crucial to future space ventures, like the development of Space Station Freedom, the establishment of lunar colonies, and the exploration of other planets. Principal investigators are identified for each experiment.

  14. First International Microgravity Laboratory

    NASA Technical Reports Server (NTRS)

    Mcmahan, Tracy; Shea, Charlotte; Wiginton, Margaret; Neal, Valerie; Gately, Michele; Hunt, Lila; Graben, Jean; Tiderman, Julie; Accardi, Denise

    1990-01-01

    This colorful booklet presents capsule information on every aspect of the International Microgravity Laboratory (IML). As part of Spacelab, IML is divided into Life Science Experiments and Materials Science Experiments. Because the life and materials sciences use different Spacelab resources, they are logically paired on the IML missions. Life science investigations generally require significant crew involvement, and crew members often participate as test subjects or operators. Materials missions capitalize on these complementary experiments. International cooperation consists in participation by the European Space Agency, Canada, France, Germany, and Japan who are all partners in developing hardware and experiments of IML missions. IML experiments are crucial to future space ventures, like the development of Space Station Freedom, the establishment of lunar colonies, and the exploration of other planets. Principal investigators are identified for each experiment.

  15. Laboratory for Radiokrypton Dating

    NASA Astrophysics Data System (ADS)

    Lu, Z.; Bailey, K.; Jiang, W.; Müller, P.; O'Connor, T. P.; Zappala, J. C.

    2013-12-01

    Due to its simple production and transport processes in the terrestrial environment, the long-lived noble-gas isotope 81Kr (half-life = 230 kyr) is the ideal tracer for studying old water and ice in the age range of 10^5-10^6 years, a range beyond the reach of 14C. 81Kr dating, a concept pursued in the past four decades by numerous laboratories employing a variety of techniques, is now available for the first time to the earth science community at large. This is made possible by the development of ATTA-3 (Jiang et al., GCA 91, 1-6; 2012), an efficient and selective atom counter based on the Atom Trap Trace Analysis method (Chen et al., Science 286, 1139-1141; 1999). The instrument is capable of measuring both 81Kr/Kr and 85Kr/Kr ratios of environmental samples in the range of 10^-14-10^-10. For 81Kr-dating in the age range of 150 - 1,500 kyr, the required sample size is 5 - 10 micro-L STP of krypton gas, which can be extracted from approximately 100 - 200 kg of water or 40 - 80 kg of ice. For 85Kr/Kr analysis, the required sample size is generally smaller by an order of magnitude because of the isotope's higher initial abundance in the atmosphere. The Laboratory for Radiokrypton Dating is currently equipped to analyze up to 120 samples per year. With future equipment upgrades, this limit can be increased as demand grows. In the period since November 2011, the Laboratory has measured both 81Kr/Kr and 85Kr/Kr ratios in over 50 samples that had been extracted by collaborators from six different continents. The samples were from groundwater wells in the Great Artesian Basin (Australia), Guarani Aquifer (Brazil), and Locust Grove (Maryland); from brine wells of the Waste Isolation Pilot Plant (New Mexico); from geothermal steam vents in Yellowstone National Park; from near-surface ice at Taylor Glacier, Antarctica; and from deep mines in South Africa. Sample collection and purification was performed by groups including the University of Illinois at Chicago, University

  16. FORT Molecular Ecology Laboratory

    USGS Publications Warehouse

    Oyler-McCance, Sara J.; Stevens, P.D.

    2011-01-01

    The mission of the U.S. Geological Survey (USGS) at the Fort Collins Science Center Molecular Ecology Laboratory is to use the tools and concepts of molecular genetics to address a variety of complex management questions and conservation issues facing the management of the Nation's fish and wildlife resources. Together with our partners, we design and implement studies to document genetic diversity and the distribution of genetic variation among individuals, populations, and species. Information from these studies is used to support wildlife-management planning and conservation actions. Current and past studies have provided information to assess taxonomic boundaries, inform listing decisions made under the Endangered Species Act, identify unique or genetically depauperate populations, estimate population size or survival rates, develop management or recovery plans, breed wildlife in captivity, relocate wildlife from one location to another, and assess the effects of environmental change.

  17. Tochilinite Produced in Laboratory

    NASA Astrophysics Data System (ADS)

    Kozerenko, S. V.; Organova, N. J.; Fadeev, V. V.; Magazina, L. O.; Kolpakova, N. N.; Kopneva, L. A.

    1996-03-01

    Tochilinite was firstly identified in the serpentinites from Voronezh region, Russia, in 1971. Later this mineral was recognized to be a major matrix phase of the most primitive carbonaceous chondrites (CI, CM) where tochilinite as a mixed-layer structure occurs among serpentine group minerals, olivine, pyroxene, pyrrhotite etc. Terrestrial tochilinite has been suggested to result from low-temperature hydrothermal alteration of serpentinite. The origin of the chondritic tochilinite is still not known, partly because of failure to synthesis this mineral. As for as we know, since 1971, there was no publication about successful synthesis of tochilinite. Here we present results of the first laboratory synthesis of tochilinite as a product of interaction of Fe(II) hydroxides with H2S at 80 degrees C, and total concentration of reduced sulfur ions in solution lower than 10-4M at pH 7.8 and lower than 1M at pH 11.5.

  18. Mars Science Laboratory Drill

    NASA Technical Reports Server (NTRS)

    Okon, Avi B.

    2010-01-01

    The Drill for the Mars Science Laboratory mission is a rotary-percussive sample acquisition device with an emphasis on toughness and robustness to handle the harsh environment on Mars. The unique challenges associated with autonomous drilling from a mobile robot are addressed. A highly compressed development schedule dictated a modular design architecture that satisfies the functional and load requirements while allowing independent development and testing of the Drill subassemblies. The Drill consists of four actuated mechanisms: a spindle that rotates the bit, a chuck that releases and engages bits, a novel voice-coil-based percussion mechanism that hammers the bit, and a linear translation mechanism. The Drill has three passive mechanisms: a replaceable bit assembly that acquires and collects sample, a contact sensor / stabilizer mechanism, and, lastly a flex harness service loop. This paper describes the various mechanisms that makeup the Drill and discusses the solutions to their unique design and development challenges.

  19. Laminar laboratory rivers

    NASA Astrophysics Data System (ADS)

    Seizilles, Grégoire; Devauchelle, Olivier; Lajeunesse, Éric; Métivier, François

    2014-05-01

    A viscous fluid flowing over fine plastic grains spontaneously channelizes into a few centimeters-wide river. After reaching its equilibrium shape, this stable laboratory flume is able to carry a steady load of sediments, like many alluvial rivers. When the sediment discharge vanishes, the river size, shape and slope fit the threshold theory proposed by Glover and Florey (1951), which assumes that the Shields parameter is critical on the channel bed. As the sediment discharge is increased, the river widens and flattens. Surprisingly, the aspect ratio of its cross section depends on the sediment discharge only, regardless of the water discharge. We propose a theoretical interpretation of these findings based on the balance between gravity, which pulls particles towards the center of the channel, and the diffusion of bedload particles, which pushes them away from areas of intense bedload.

  20. The autonomic laboratory

    NASA Technical Reports Server (NTRS)

    Low, P. A.; Opfer-Gehrking, T. L.

    1999-01-01

    The autonomic nervous system can now be studied quantitatively, noninvasively, and reproducibly in a clinical autonomic laboratory. The approach at the Mayo Clinic is to study the postganglionic sympathetic nerve fibers of peripheral nerve (using the quantitative sudomotor axon reflex test [QSART]), the parasympathetic nerves to the heart (cardiovagal tests), and the regulation of blood pressure by the baroreflexes (adrenergic tests). Patient preparation is extremely important, since the state of the patient influences the results of autonomic function tests. The autonomic technologist in this evolving field needs to have a solid core of knowledge of autonomic physiology and autonomic function tests, followed by training in the performance of these tests in a standardized fashion. The range and utilization of tests of autonomic function will likely continue to evolve.

  1. Los Alamos National Laboratory

    SciTech Connect

    Dogliani, Harold O

    2011-01-19

    The purpose of the briefing is to describe general laboratory technical capabilities to be used for various groups such as military cadets or university faculty/students and post docs to recruit into a variety of Los Alamos programs. Discussed are: (1) development and application of high leverage science to enable effeictive, predictable and reliability outcomes; (2) deter, detect, characterize, reverse and prevent the proliferation of weapons of mass destruction and their use by adversaries and terrorists; (3) modeling and simulation to define complex processes, predict outcomes, and develop effective prevention, response, and remediation strategies; (4) energetic materials and hydrodynamic testing to develop materials for precise delivery of focused energy; (5) materials cience focused on fundamental understanding of materials behaviors, their quantum-molecular properties, and their dynamic responses, and (6) bio-science to rapidly detect and characterize pathogens, to develop vaccines and prophylactic remedies, and to develop attribution forensics.

  2. Interaction between clinic and laboratory.

    PubMed

    Armstrong, Elina; Joutsi-Korhonen, Lotta; Lassila, Riitta

    2011-01-01

    Clinicians order laboratory tests to diagnose, monitor, and screen for diseases, to evaluate or confirm previously abnormal results and to develop prognoses. The rigorous quality assurance programs, large automated processes and economic constraints may induce direct challenges to tailored diagnosis. Clinicians will have to gain an understanding of the underlying principles of laboratory technologies without losing their ability to practice 'the art of medicine' at their primary focus - the patient. Specialized laboratory services and expertise play especially important roles in coagulation hematology. Assays are technically demanding and often based on functional properties of proteins, producing results that are far more than plain numbers. Interpretation of laboratory data poses many challenges, such as pre-analytical and patient-dependent factors, of which the laboratory is often not well informed, but which the clinicians are required to take into account. The laboratory scientist needs to understand the multiple clinical circumstances causing variance or interference in the laboratory results. Direct interaction between clinic and laboratory is needed. When laboratory-specific issues are uncertain to the clinician, the laboratory scientist should become the clinician's primary consultant. The better the education and knowledge of both directions, the better the outcome. Regular multidisciplinary rounds by the clinicians and the laboratory scientists are of great benefit. This interaction at its best fosters research and development by identifying new mechanisms and tools. PMID:21193109

  3. [ISO 15189 medical laboratory accreditation].

    PubMed

    Aoyagi, Tsutomu

    2004-10-01

    This International Standard, based upon ISO/IEC 17025 and ISO 9001, provides requirements for competence and quality that are particular to medical laboratories. While this International Standard is intended for use throughout the currently recognized disciplines of medical laboratory services, those working in other services and disciplines will also find it useful and appropriate. In addition, bodies engaged in the recognition of the competence of medical laboratories will be able to use this International Standard as the basis for their activities. The Japan Accreditation Board for Conformity Assessment (AB) and the Japanese Committee for Clinical Laboratory Standards (CCLS) are jointly developing the program of accreditation of medical laboratories. ISO 15189 requirements consist of two parts, one is management requirements and the other is technical requirements. The former includes the requirements of all parts of ISO 9001, moreover it includes the requirement of conformity assessment body, for example, impartiality and independence from any other party. The latter includes the requirements of laboratory competence (e.g. personnel, facility, instrument, and examination methods), moreover it requires that laboratories shall participate proficiency testing(s) and laboratories' examination results shall have traceability of measurements and implement uncertainty of measurement. Implementation of ISO 15189 will result in a significant improvement in medical laboratories management system and their technical competence. The accreditation of medical laboratory will improve medical laboratory service and be useful for patients. PMID:15624503

  4. The Laboratory for Terrestrial Physics

    NASA Technical Reports Server (NTRS)

    2003-01-01

    The Laboratory for Terrestrial Physics is dedicated to the advancement of knowledge in Earth and planetary science, by conducting innovative research using space technology. The Laboratory's mission and activities support the work and new initiatives at NASA's Goddard Space Flight Center (GSFC). The Laboratory's success contributes to the Earth Science Directorate as a national resource for studies of Earth from Space. The Laboratory is part of the Earth Science Directorate based at the GSFC in Greenbelt, MD. The Directorate itself is comprised of the Global Change Data Center (GCDC), the Space Data and Computing Division (SDCD), and four science Laboratories, including Laboratory for Terrestrial Physics, Laboratory for Atmospheres, and Laboratory for Hydrospheric Processes all in Greenbelt, MD. The fourth research organization, Goddard Institute for Space Studies (GISS), is in New York, NY. Relevant to NASA's Strategic Plan, the Laboratory ensures that all work undertaken and completed is within the vision of GSFC. The philosophy of the Laboratory is to balance the completion of near term goals, while building on the Laboratory's achievements as a foundation for the scientific challenges in the future.

  5. Creating the laboratory`s future; A strategy for Lawrence Livermore National Laboratory

    SciTech Connect

    1997-09-01

    ``Creating The Laboratory`s Future`` describes Livermore`s roles and responsibilities as a Department of Energy (DOE) national laboratory and sets the foundation for decisions about the Laboratory`s programs and operations. It summarizes Livermore`s near-term strategy, which builds on recent Lab achievements and world events affecting their future. It also discusses their programmatic and operational emphases and highlights program areas that the authors believe can grow through application of Lab science and technology. Creating the Laboratory`s Future reflects their very strong focus on national security, important changes in the character of their national security work, major efforts are under way to overhaul their administrative and operational systems, and the continuing challenge of achieving national consensus on the role of the government in energy, environment, and the biosciences.

  6. Automated Microbial Metabolism Laboratory

    NASA Technical Reports Server (NTRS)

    1972-01-01

    The Automated Microbial Metabolism Laboratory (AMML) 1971-1972 program involved the investigation of three separate life detection schemes. The first was a continued further development of the labeled release experiment. The possibility of chamber reuse without inbetween sterilization, to provide comparative biochemical information was tested. Findings show that individual substrates or concentrations of antimetabolites may be sequentially added to a single test chamber. The second detection system which was investigated for possible inclusion in the AMML package of assays, was nitrogen fixation as detected by acetylene reduction. Thirdly, a series of preliminary steps were taken to investigate the feasibility of detecting biopolymers in soil. A strategy for the safe return to Earth of a Mars sample prior to manned landings on Mars is outlined. The program assumes that the probability of indigenous life on Mars is unity and then broadly presents the procedures for acquisition and analysis of the Mars sample in a manner to satisfy the scientific community and the public that adequate safeguards are being taken.

  7. Laboratory development TPV generator

    SciTech Connect

    Holmquist, G.A.; Wong, E.M.; Waldman, C.H.

    1996-02-01

    A laboratory model of a TPV generator in the kilowatt range was developed and tested. It was based on methane/oxygen combustion and a spectrally matched selective emitter/collector pair (ytterbia emitter-silicon PV cell). The system demonstrated a power output of 2.4 kilowatts at an overall efficiency of 4.5{percent} without recuperation of heat from the exhaust gases. Key aspects of the effort include: (1) process development and fabrication of mechanically strong selective emitter ceramic textile materials; (2) design of a stirred reactor emitter/burner capable of handling up to 175,000 Btu/hr fuel flows; (3) support to the developer of the production silicon concentrator cells capable of withstanding TPV environments; (4) assessing the apparent temperature exponent of selective emitters; and (5) determining that the remaining generator efficiency improvements are readily defined combustion engineering problems that do not necessitate breakthrough technology. The fiber matrix selective emitter ceramic textile (felt) was fabricated by a relic process with the final heat-treatment controlling the grain growth in the porous ceramic fiber matrix. This textile formed a cylindrical cavity for a stirred reactor. The ideal stirred reactor is characterized by constant temperature combustion resulting in a uniform reactor temperature. This results in a uniform radiant emission from the emitter. As a result of significant developments in the porous emitter matrix technology, a TPV generator burner/emitter was developed that produced kilowatts of radiant energy. {copyright} {ital 1996 American Institute of Physics.}

  8. Spectrometers beyond the laboratory

    SciTech Connect

    Wadsworth, W.

    1996-11-01

    Two new types of miniature Fourier Transform Spectrometers (FTS) presently being built have enabled this technology to be taken out of the laboratory and into the field. Both designs are very rugged, use little power to run, and can be made extremely small and lightweight. They are excellent candidates for airborne use, both in aircraft and satellite applications. One, the Mcro FT, is a mass balanced linear reciprocating scan operating in the 1-2 scan per second speed range. The other, the Turbo FT, uses a rotary scan, enabling it to run at much higher speeds, from 10 to 1000 scans per second. Either type can be built in the visible, near K and thermal IR wavelength ranges, and provide spectral resolution of 1-2 wave-numbers. Results obtained in all these wavelength ranges are presented here. The rotary configuration is more suited to airborne and satellite survey type deployments, due mostly to its rapid scan rate. Either of these sensors will fit into a small, commercially available stabilized pod which can easily be attached to a helicopter or light plane. This results in a very economical flight spectrometer system. 11 figs.

  9. BNL Sources Development Laboratory

    SciTech Connect

    Ben-Zvi, I.; Graves, W.; Heese, R.; Johnson, E.D.; Krinsky, S.; Yu, L.H.

    1997-01-01

    The NSLS has a long-standing interest in providing the best possible synchrotron radiation sources for its user community, and hence, has recently established the Source Development Laboratory (SDL) to pursue research into fourth generation synchrotron radiation sources. A major element of the program includes development of a high peak power FEL meant to operate in the vacuum ultraviolet. The objective of the program is to develop the source, and experimental technology together to provide the greatest impact on UV science. The accelerator under construction for the SDL consists of a high brightness RF photocathode electron gun followed by a 230 MeV short pulse linac incorporating a magnetic chicane for pulse compression. The gun drive laser is a wide bandwidth Ti: Sapphire regenerative amplifier capable of pulse shaping which will be used to study non- linear emittance compensation. Using the compressor, 1 nC bunches with a length as small as 50 {mu}m sigma (2 kA peak current) are available for experiments. In this paper we briefly describe the facility and detail our plans for utilizing the 10 m long NISUS wiggler to carry out single pass FEL experiments. These include a 1 {mu}m SASE demonstration, a seeded beam demonstration at 300 nm, and a High Gain Harmonic Generation experiment at 200 mn. The application of chirped pulse amplification to this type of FEL will also be discussed.

  10. Whole Class Laboratories: More Examples

    NASA Astrophysics Data System (ADS)

    Kouh, Minjoon

    2016-03-01

    Typically, introductory physics courses are taught with a combination of lectures and laboratories in which students have opportunities to discover the natural laws through hands-on activities in small groups. This article reports the use of Google Drive, a free online document-sharing tool, in physics laboratories for pooling experimental data from the whole class. This pedagogical method was reported earlier, and the present article offers a few more examples of such "whole class" laboratories.

  11. Ethical Inspection about laboratory animals.

    PubMed

    Yang, Nai-bin; Pan, Xiao-jun; Cheng, Jing-jing; Lin, Jia-qiang; Zhu, Jia-yin

    2015-11-01

    Laboratory animals and animal experiments are foundations and important support conditions for life sciences, especially for medical research. The animal experiments have drawn extensive attention from the society because of the ethical issue. This paper takes Wenzhou Medical University as an example to give a brief introduction to the ethical review about laboratory animals in the university so as to further draw attention and concerns from the public about the ethical issue of laboratory animals. We successively introduce its scientific projects, nurturing environment and ethical review of laboratory animals. PMID:27215017

  12. Mice examined in Animal Laboratory of Lunar Receiving Laboratory

    NASA Technical Reports Server (NTRS)

    1969-01-01

    Landrum Young (seated), Brown and Root-Northrup, and Russell Stullken, Manned Spacecraft Center, examine mice in the Animal laboratory of the Lunar Receiving Laboratory which have been inoculated with lunar sample material. wish for peace for all mankind. astronauts will be released from quarantine on August 11, 1969. Donald K. Slayton (right), MSC Director of Flight Crew Operations; and Lloyd Reeder, training coordinator.

  13. Wentworth Institute Mechanical Engineering Laboratory Manual. Laboratory Study Guide.

    ERIC Educational Resources Information Center

    Avakian, Harry; And Others

    This publication is a laboratory study guide designed for mechanical engineering students. All of the experiments (with the exception of experiment No. 1) contained in the Mechanical Engineering Laboratory Manual have been included in this guide. Brief theoretical backgrounds, examples and their solutions, charts, graphs, illustrations, and…

  14. Laboratory for Radiokrypton Dating

    NASA Astrophysics Data System (ADS)

    Zappala, J. C.; Jiang, W.; Bailey, K. G.; Lu, Z. T.; Mueller, P.; O'Connor, T. P.

    2015-12-01

    Due to its simple production and transport in the terrestrial environment, 81Kr (half-life = 230,000 yr) is the ideal tracer for old water and ice with mean residence times in the range of 105-106 years, a range beyond the reach of 14C. 81Kr-dating is now available to the earth science community at large thanks to the development of an efficient and selective atom counter based on the Atom Trap Trace Analysis (ATTA) method. ATTA is a laser-based atom counting method where individual neutral atoms of the desired isotope are selectively captured by laser beams, and their fluorescence detected via a CCD camera. ATTA is unique among trace analysis techniques in that it is free of interferences from any other isotopes, isobars, atomic or molecular species. The ATTA instrument at Argonne's Laboratory for Radiokrypton Dating is capable of measuring both 81Kr/Kr and 85Kr/Kr ratios of environmental samples in the range of 10-14-10-10. For 81Kr-dating in the age range of 150 kyr - 1500 kyr, the required sample size is 5 micro-L STP of krypton gas, which can be extracted from approximately 100 kg of water or 40 kg of ice. For 85Kr/Kr analysis, the sample size can be smaller by an order of magnitude. We are continually developing the method towards higher counting efficiency, smaller sample sizes requirements, and higher sample throughput rates. In the past four years, we have performed radiokrypton analysis of over 150 groundwater and ice samples extracted by collaborators from all seven continents. Sample collection and purification was performed by groups including the University of Chicago, the University of Illinois at Chicago, the University of Bern, and the International Atomic Energy Agency. This work is supported by the U.S. DOE, Office of Nuclear Physics, under contract DE-AC02-06CH11357.

  15. Alternative Fuels Research Laboratory

    NASA Technical Reports Server (NTRS)

    Surgenor, Angela D.; Klettlinger, Jennifer L.; Nakley, Leah M.; Yen, Chia H.

    2012-01-01

    NASA Glenn has invested over $1.5 million in engineering, and infrastructure upgrades to renovate an existing test facility at the NASA Glenn Research Center (GRC), which is now being used as an Alternative Fuels Laboratory. Facility systems have demonstrated reliability and consistency for continuous and safe operations in Fischer-Tropsch (F-T) synthesis and thermal stability testing. This effort is supported by the NASA Fundamental Aeronautics Subsonic Fixed Wing project. The purpose of this test facility is to conduct bench scale F-T catalyst screening experiments. These experiments require the use of a synthesis gas feedstock, which will enable the investigation of F-T reaction kinetics, product yields and hydrocarbon distributions. Currently the facility has the capability of performing three simultaneous reactor screening tests, along with a fourth fixed-bed reactor for catalyst activation studies. Product gas composition and performance data can be continuously obtained with an automated gas sampling system, which directly connects the reactors to a micro-gas chromatograph (micro GC). Liquid and molten product samples are collected intermittently and are analyzed by injecting as a diluted sample into designated gas chromatograph units. The test facility also has the capability of performing thermal stability experiments of alternative aviation fuels with the use of a Hot Liquid Process Simulator (HLPS) (Ref. 1) in accordance to ASTM D 3241 "Thermal Oxidation Stability of Aviation Fuels" (JFTOT method) (Ref. 2). An Ellipsometer will be used to study fuel fouling thicknesses on heated tubes from the HLPS experiments. A detailed overview of the test facility systems and capabilities are described in this paper.

  16. Laboratory volcano geodesy

    NASA Astrophysics Data System (ADS)

    Færøvik Johannessen, Rikke; Galland, Olivier; Mair, Karen

    2014-05-01

    Magma transport in volcanic plumbing systems induces surface deformation, which can be monitored by geodetic techniques, such as GPS and InSAR. These geodetic signals are commonly analyzed through geodetic models in order to constrain the shape of, and the pressure in, magma plumbing systems. These models, however, suffer critical limitations: (1) the modelled magma conduit shapes cannot be compared with the real conduits, so the geodetic models cannot be tested nor validated; (2) the modelled conduits only exhibit shapes that are too simplistic; (3) most geodetic models only account for elasticity of the host rock, whereas substantial plastic deformation is known to occur. To overcome these limitations, one needs to use a physical system, in which (1) both surface deformation and the shape of, and pressure in, the underlying conduit are known, and (2) the mechanical properties of the host material are controlled and well known. In this contribution, we present novel quantitative laboratory results of shallow magma emplacement. Fine-grained silica flour represents the brittle crust, and low viscosity vegetable oil is an analogue for the magma. The melting temperature of the oil is 31°C; the oil solidifies in the models after the end of the experiments. At the time of injection the oil temperature is 50°C. The oil is pumped from a reservoir using a volumetric pump into the silica flour through a circular inlet at the bottom of a 40x40 cm square box. The silica flour is cohesive, such that oil intrudes it by fracturing it, and produces typical sheet intrusions (dykes, cone sheets, etc.). During oil intrusion, the model surface deforms, mostly by doming. These movements are measured by an advanced photogrammetry method, which uses 4 synchronized fixed cameras that periodically image the surface of the model from different angles. We apply particle tracking method to compute the 3D ground deformation pattern through time. After solidification of the oil, the

  17. Australia's marine virtual laboratory

    NASA Astrophysics Data System (ADS)

    Proctor, Roger; Gillibrand, Philip; Oke, Peter; Rosebrock, Uwe

    2014-05-01

    In all modelling studies of realistic scenarios, a researcher has to go through a number of steps to set up a model in order to produce a model simulation of value. The steps are generally the same, independent of the modelling system chosen. These steps include determining the time and space scales and processes of the required simulation; obtaining data for the initial set up and for input during the simulation time; obtaining observation data for validation or data assimilation; implementing scripts to run the simulation(s); and running utilities or custom-built software to extract results. These steps are time consuming and resource hungry, and have to be done every time irrespective of the simulation - the more complex the processes, the more effort is required to set up the simulation. The Australian Marine Virtual Laboratory (MARVL) is a new development in modelling frameworks for researchers in Australia. MARVL uses the TRIKE framework, a java-based control system developed by CSIRO that allows a non-specialist user configure and run a model, to automate many of the modelling preparation steps needed to bring the researcher faster to the stage of simulation and analysis. The tool is seen as enhancing the efficiency of researchers and marine managers, and is being considered as an educational aid in teaching. In MARVL we are developing a web-based open source application which provides a number of model choices and provides search and recovery of relevant observations, allowing researchers to: a) efficiently configure a range of different community ocean and wave models for any region, for any historical time period, with model specifications of their choice, through a user-friendly web application, b) access data sets to force a model and nest a model into, c) discover and assemble ocean observations from the Australian Ocean Data Network (AODN, http://portal.aodn.org.au/webportal/) in a format that is suitable for model evaluation or data assimilation, and

  18. Managing a Computer Teaching Laboratory.

    ERIC Educational Resources Information Center

    Macey, Susan M.

    1998-01-01

    Examines issues concerning the initial setup and the everyday operational problems of managing a computer teaching laboratory. Addresses such issues as setting policies on laboratory access, dealing with a high student-per-machine ratio, provisions for maintenance, obtaining hardware and software upgrades, staffing, data security, and networking…

  19. Undergraduate Organic Chemistry Laboratory Safety

    NASA Astrophysics Data System (ADS)

    Luckenbaugh, Raymond W.

    1996-11-01

    Each organic chemistry student should become familiar with the educational and governmental laboratory safety requirements. One method for teaching laboratory safety is to assign each student to locate safety resources for a specific class laboratory experiment. The student should obtain toxicity and hazardous information for all chemicals used or produced during the assigned experiment. For example, what is the LD50 or LC50 for each chemical? Are there any specific hazards for these chemicals, carcinogen, mutagen, teratogen, neurotixin, chronic toxin, corrosive, flammable, or explosive agent? The school's "Chemical Hygiene Plan", "Prudent Practices for Handling Hazardous Chemicals in the Laboratory" (National Academy Press), and "Laboratory Standards, Part 1910 - Occupational Safety and Health Standards" (Fed. Register 1/31/90, 55, 3227-3335) should be reviewed for laboratory safety requirements for the assigned experiment. For example, what are the procedures for safe handling of vacuum systems, if a vacuum distillation is used in the assigned experiment? The literature survey must be submitted to the laboratory instructor one week prior to the laboratory session for review and approval. The student should then give a short presentation to the class on the chemicals' toxicity and hazards and describe the safety precautions that must be followed. This procedure gives the student first-hand knowledge on how to find and evaluate information to meet laboartory safety requirements.

  20. LABORATORY DESIGN CONSIDERATIONS FOR SAFETY.

    ERIC Educational Resources Information Center

    National Safety Council, Chicago, IL. Campus Safety Association.

    THIS SET OF CONSIDERATIONS HAS BEEN PREPARED TO PROVIDE PERSONS WORKING ON THE DESIGN OF NEW OR REMODELED LABORATORY FACILITIES WITH A SUITABLE REFERENCE GUIDE TO DESIGN SAFETY. THERE IS NO DISTINCTION BETWEEN TYPES OF LABORATORY AND THE EMPHASIS IS ON GIVING GUIDES AND ALTERNATIVES RATHER THAN DETAILED SPECIFICATIONS. AREAS COVERED INCLUDE--(1)…

  1. The Laboratory for Learning Resourses

    ERIC Educational Resources Information Center

    Spilman, Edra L.

    1973-01-01

    Laboratories for Learning Resourses, instead of replacing or competing with the medical library, should provide a learning environment for medical students, with books, laboratory-lecture presentations, slide-sound programs, films, videotapes, computer models and programs, museum specimens and charts. (Author/PG)

  2. Three Puzzles for Organic Laboratory.

    ERIC Educational Resources Information Center

    Todd, David; Pickering, Miles

    1988-01-01

    Notes that laboratory work should be more oriented towards puzzle solving rather than technique or illustration. Offers three organic laboratory puzzles which can be solved by melting point alone. Involves lab work at the 100-200-mg scale but still uses conventional glassware. (MVL)

  3. Laboratory Activities for Introductory Astronomy

    ERIC Educational Resources Information Center

    Kruglak, Haym

    1973-01-01

    Presents sample laboratory activities designed for use in astronomy teaching, including naked eye observations, instrument construction, student projects, and cloudy weather activities. Appended are bibliographies of journal articles and reference books and lists of films, laboratory manuals, and distributors of apparatus and teaching aids. (CC)

  4. An Advanced Chemistry Laboratory Program.

    ERIC Educational Resources Information Center

    Wise, John H.

    The Advanced Chemistry Laboratory Program is a project designed to devise experiments to coordinate the use of instruments in the laboratory programs of physical chemistry, instrumental analysis, and inorganic chemistry at the advanced undergraduate level. It is intended that such experiments would incorporate an introduction to the instrument…

  5. OCCUPATION--LANGUAGE LABORATORY DIRECTOR.

    ERIC Educational Resources Information Center

    TURNER, DAYMOND

    TRUE PROFESSIONAL STATUS FOR A LABORATORY DIRECTOR, PLUS ADMINISTRATIVE SUPPORT OF SUCH INSTRUCTION, WILL GIVE COLLEGES AND UNIVERSITIES ADEQUATE RETURN FOR THEIR INVESTMENT IN ELECTRONIC EQUIPMENT. BY BEING INVOLVED IN IMPORTANT RESEARCH AND INSTRUCTIONAL ACTIVITIES, THE DIRECTOR OF A LANGUAGE LABORATORY CAN SERVE ALSO TO FREE THE TEACHER AND…

  6. Whole Class Laboratories: More Examples

    ERIC Educational Resources Information Center

    Kouh, Minjoon

    2016-01-01

    Typically, introductory physics courses are taught with a combination of lectures and laboratories in which students have opportunities to discover the natural laws through hands-on activities in small groups. This article reports the use of Google Drive, a free online document-sharing tool, in physics laboratories for pooling experimental data…

  7. Simulated Laboratory in Digital Logic.

    ERIC Educational Resources Information Center

    Cleaver, Thomas G.

    Design of computer circuits used to be a pencil and paper task followed by laboratory tests, but logic circuit design can now be done in half the time as the engineer accesses a program which simulates the behavior of real digital circuits, and does all the wiring and testing on his computer screen. A simulated laboratory in digital logic has been…

  8. A laboratory animal science pioneer.

    PubMed

    Kostomitsopoulos, Nikolaos

    2014-11-01

    Nikolaos Kostomitsopoulos, DVM, PhD, is Head of Laboratory Animal Facilities and Designated Veterinarian, Center of Clinical, Experimental Surgery and Translational Research, Biomedical Research Foundation of the Academy of Athens, Athens, Greece. Dr. Kostomitsopoulos discusses his successes in implementing laboratory animal science legislation and fostering collaboration among scientists in Greece. PMID:25333597

  9. Dental Laboratory Technology Program Standards.

    ERIC Educational Resources Information Center

    Georgia Univ., Athens. Dept. of Vocational Education.

    This guide contains 45 program standards for the dental laboratory technology program conducted in technical institutes in Georgia. The dental laboratory technology program, either diploma or associate degree, is designed to ensure that students gain basic competence in the job skills needed for an entry-level employee in dental laboratory…

  10. Federal Laboratory Consortium Resource Directory.

    ERIC Educational Resources Information Center

    Federal Laboratory Consortium, Washington, DC.

    Designed to bridge the communication gap between the Federal Laboratory Consortium (FLC) and public and private sectors of the country, this directory has been prepared as a compilation of scientific and technical research and development activities at federal laboratories, which are directing technology transfer efforts toward increasing the use…

  11. Laboratory Manual, Electrical Engineering 25.

    ERIC Educational Resources Information Center

    Syracuse Univ., NY. Dept. of Electrical Engineering.

    Developed as part of a series of materials in the electrical engineering sequence developed under contract with the United States Office of Education, this laboratory manual provides nine laboratory projects suitable for a second course in electrical engineering. Dealing with resonant circuits, electrostatic fields, magnetic devices, and…

  12. Medical Laboratory Assistant. Student's Manual.

    ERIC Educational Resources Information Center

    Barnett, Sara

    This student's manual for the medical laboratory student is one of a series of self-contained, individualized instructional materials for students enrolled in training within the allied health field. It is intended to provide study materials and learning activities that are general enough for all medical laboratory students to use to enhance their…

  13. Trial of Integrated Laboratory Practice

    ERIC Educational Resources Information Center

    Matsuo, Osamu; Takahashi, Yuzo; Abe, Chikara; Tanaka, Kunihiko; Nakashima, Akira; Morita, Hironobu

    2011-01-01

    In most laboratory practices for students in medical schools, a laboratory guidebook is given to the students, in which the procedures are precisely described. The students merely follow the guidebook without thinking deeply, which spoils the students and does not entice them to think creatively. Problem-based learning (PBL) could be one means for…

  14. Dental Laboratory Technology Program Guide.

    ERIC Educational Resources Information Center

    Georgia Univ., Athens. Dept. of Vocational Education.

    This program guide contains the standard dental laboratory technology curriculum for both diploma programs and associate degree programs in technical institutes in Georgia. The curriculum encompasses the minimum competencies required for entry-level workers in the dental laboratory technology field. The general information section contains the…

  15. Testing containment of laboratory hoods

    SciTech Connect

    Knutson, G.W.

    1987-06-01

    Laboratory fume hoods often do not adequately provide protection to a chemist or technician at the hood. The reason for failure of the hoods to perform adequately are varied and, in many instances, difficult to determine. In some cases, the laboratory hood manufacturer has provided equipment that does not reflect the state of art in controlling laboratory exposures. In other cases, the architect or engineer has disregarded the function of the hood thus the design of the installation is faulty and the hood will not work. The contractor may have installed the system so poorly that it will not adequately function. Finally, the chemist or technician may misuse the hood, causing poor performance. This paper considers a method of evaluating the performance of laboratory fume hoods. Using the method, the paper examines several instances where the laboratory fume hood performed inadequately, quantifies the performance and identifies the cause of poor performance.

  16. Mars Science Laboratory Drill

    NASA Technical Reports Server (NTRS)

    Okon, Avi B.; Brown, Kyle M.; McGrath, Paul L.; Klein, Kerry J.; Cady, Ian W.; Lin, Justin Y.; Ramirez, Frank E.; Haberland, Matt

    2012-01-01

    This drill (see Figure 1) is the primary sample acquisition element of the Mars Science Laboratory (MSL) that collects powdered samples from various types of rock (from clays to massive basalts) at depths up to 50 mm below the surface. A rotary-percussive sample acquisition device was developed with an emphasis on toughness and robustness to handle the harsh environment on Mars. It is the first rover-based sample acquisition device to be flight-qualified (see Figure 2). This drill features an autonomous tool change-out on a mobile robot, and novel voice-coil-based percussion. The drill comprises seven subelements. Starting at the end of the drill, there is a bit assembly that cuts the rock and collects the sample. Supporting the bit is a subassembly comprising a chuck mechanism to engage and release the new and worn bits, respectively, and a spindle mechanism to rotate the bit. Just aft of that is a percussion mechanism, which generates hammer blows to break the rock and create the dynamic environment used to flow the powdered sample. These components are mounted to a translation mechanism, which provides linear motion and senses weight-on-bit with a force sensor. There is a passive-contact sensor/stabilizer mechanism that secures the drill fs position on the rock surface, and flex harness management hardware to provide the power and signals to the translating components. The drill housing serves as the primary structure of the turret, to which the additional tools and instruments are attached. The drill bit assembly (DBA) is a passive device that is rotated and hammered in order to cut rock (i.e. science targets) and collect the cuttings (powder) in a sample chamber until ready for transfer to the CHIMRA (Collection and Handling for Interior Martian Rock Analysis). The DBA consists of a 5/8-in. (.1.6- cm) commercial hammer drill bit whose shank has been turned down and machined with deep flutes designed for aggressive cutting removal. Surrounding the shank of the

  17. OSHA Laboratory Standard: Driving Force for Laboratory Safety!

    ERIC Educational Resources Information Center

    Roy, Kenneth R.

    2000-01-01

    Discusses the Occupational Safety and Health Administration's (OSHA's) Laboratory Safety Standards as the major driving force in establishing and maintaining a safe working environment for teachers and students. (Author)

  18. Making Laboratories Count -- Better Integration of Laboratories in Physics Courses

    NASA Astrophysics Data System (ADS)

    Sizemore, Jim

    2011-10-01

    The quality of K-12 education leaves something to be desired and presents higher education faculty with the challenge of instructing under-prepared students. However, by their own admission, students from many institutions inform us that laboratory sections in science classes, including physics, consist mostly of showing up, going through the motions, and getting grades that boost their overall grade. This work presents laboratories that challenge students to take their laboratory work more seriously including specific rubrics enforcing SOLVE and Bloom's Taxonomy, pre-lab preparation work, and quizzes on pre-lab preparation. Early results are encouraging revealing greater student progress with better integration of laboratory with the rest of a complete physics course.

  19. Laboratory cost and utilization containment.

    PubMed

    Steiner, J W; Root, J M; White, D C

    1991-01-01

    The authors analyzed laboratory costs and utilization in 3,771 cases of Medicare inpatients admitted to a New England academic medical center ("the Hospital") from October 1, 1989 to September 30, 1990. The data were derived from the Hospital's Decision Resource System comprehensive data base. The authors established a historical reference point for laboratory costs as a percentage of total inpatient costs using 1981-82 Medicare claims data and cost report information. Inpatient laboratory costs were estimated at 9.5% of total inpatient costs for pre-Diagnostic Related Groups (DRGs) Medicare discharges. Using this reference point and adjusting for the Hospital's 1990 case mix, the "expected" laboratory cost was 9.3% of total cost. In fact, the cost averaged 11.5% (i.e., 24% above the expected cost level), and costs represented an even greater percentage of DRG reimbursement at 12.9%. If we regard the reimbursement as a total cost target (to eliminate losses from Medicare), then that 12.9% is 39% above the "expected" laboratory proportion of 9.3%. The Hospital lost an average of $1,091 on each DRG inpatient. The laboratory contributed 29% to this loss per case. Compared to other large hospitals, the Hospital was slightly (3%) above the mean direct cost per on-site test and significantly (58%) above the mean number of inpatient tests per inpatient day compared to large teaching hospitals. The findings suggest that careful laboratory cost analyses will become increasingly important as the proportion of patients reimbursed in a fixed manner grows. The future may hold a prospective zero-based laboratory budgeting process based on predictable patterns of DRG admissions or other fixed-reimbursement admission and laboratory utilization patterns. PMID:10113716

  20. Preservice laboratory education strengthening enhances sustainable laboratory workforce in Ethiopia

    PubMed Central

    2013-01-01

    Background There is a severe healthcare workforce shortage in sub Saharan Africa, which threatens achieving the Millennium Development Goals and attaining an AIDS-free generation. The strength of a healthcare system depends on the skills, competencies, values and availability of its workforce. A well-trained and competent laboratory technologist ensures accurate and reliable results for use in prevention, diagnosis, care and treatment of diseases. Methods An assessment of existing preservice education of five medical laboratory schools, followed by remedial intervention and monitoring was conducted. The remedial interventions included 1) standardizing curriculum and implementation; 2) training faculty staff on pedagogical methods and quality management systems; 3) providing teaching materials; and 4) procuring equipment for teaching laboratories to provide practical skills to complement didactic education. Results A total of 2,230 undergraduate students from the five universities benefitted from the standardized curriculum. University of Gondar accounted for 252 of 2,230 (11.3%) of the students, Addis Ababa University for 663 (29.7%), Jimma University for 649 (29.1%), Haramaya University for 429 (19.2%) and Hawassa University for 237 (10.6%) of the students. Together the universities graduated 388 and 312 laboratory technologists in 2010/2011 and 2011/2012 academic year, respectively. Practical hands-on training and experience with well-equipped laboratories enhanced and ensured skilled, confident and competent laboratory technologists upon graduation. Conclusions Strengthening preservice laboratory education is feasible in resource-limited settings, and emphasizing its merits (ample local capacity, country ownership and sustainability) provides a valuable source of competent laboratory technologists to relieve an overstretched healthcare system. PMID:24164781

  1. Microwave remote sensing laboratory design

    NASA Technical Reports Server (NTRS)

    Friedman, E.

    1979-01-01

    Application of active and passive microwave remote sensing to the study of ocean pollution is discussed. Previous research efforts, both in the field and in the laboratory were surveyed to derive guidance for the design of a laboratory program of research. The essential issues include: choice of radar or radiometry as the observational technique; choice of laboratory or field as the research site; choice of operating frequency; tank sizes and material; techniques for wave generation and appropriate wavelength spectrum; methods for controlling and disposing of pollutants used in the research; and pollutants other than oil which could or should be studied.

  2. Laboratory reengineering facilitates cost management.

    PubMed

    Ellis, J E; Moser, L H

    1998-08-01

    In 1993, The Medical University of South Carolina (MUSC) in Charleston undertook a change management initiative to achieve a more cost-competitive position in its market and become a more attractive partner for a possible future affiliation with another provider organization. A key element of this change process was a reorganization of the medical center's laboratory department. Through consolidation of MUSC's separate laboratories and the introduction of a new, more efficient chemistry analyzer system, the medical center realized annual laboratory savings of approximately $1.3 million. PMID:10182277

  3. Optical Characterization Laboratory (Fact Sheet)

    SciTech Connect

    Not Available

    2011-10-01

    This fact sheet describes the purpose, lab specifications, applications scenarios, and information on how to partner with NREL's Optical Characterization Laboratory at the Energy Systems Integration Facility. The Optical Characterization Laboratory at NREL's Energy Systems Integration Facility (ESIF) conducts optical characterization of large solar concentration devices. Concentration solar power (CSP) mirror panels and concentrating solar systems are tested with an emphasis is on measurement of parabolic trough mirror panels. The Optical Characterization Laboratory provides state-of-the-art characterization and testing capabilities for assessing the optical surface quality and optical performance for various CSP technologies including parabolic troughs, linear Fresnel, dishes, and heliostats.

  4. Electromedical devices test laboratories accreditation

    NASA Astrophysics Data System (ADS)

    Murad, C.; Rubio, D.; Ponce, S.; Álvarez Abri, A.; Terrón, A.; Vicencio, D.; Fascioli, E.

    2007-11-01

    In the last years, the technology and equipment at hospitals have been increase in a great way as the risks of their implementation. Safety in medical equipment must be considered an important issue to protect patients and their users. For this reason, test and calibrations laboratories must verify the correct performance of this kind of devices under national and international standards. Is an essential mission for laboratories to develop their measurement activities taking into account a quality management system. In this article, we intend to transmit our experience working to achieve an accredited Test Laboratories for medical devices in National technological University.

  5. Extending the Marine Microcosm Laboratory

    ERIC Educational Resources Information Center

    Ryswyk, Hal Van; Hall, Eric W.; Petesch, Steven J.; Wiedeman, Alice E.

    2007-01-01

    The traditional range of marine microcosm laboratory experiments is presented as an ideal environment to teach the entire analysis process. The microcosm lab provides student-centered approach with opportunities for collaborative learning and to develop critical communication skills.

  6. Laboratory Workhorse: The Analytical Balance.

    ERIC Educational Resources Information Center

    Clark, Douglas W.

    1979-01-01

    This report explains the importance of various analytical balances in the water or wastewater laboratory. Stressed is the proper procedure for utilizing the equipment as well as the mechanics involved in its operation. (CS)

  7. Laboratory directed research and development

    SciTech Connect

    Not Available

    1991-11-15

    The purposes of Argonne's Laboratory Directed Research and Development (LDRD) Program are to encourage the development of novel concepts, enhance the Laboratory's R D capabilities, and further the development of its strategic initiatives. Among the aims of the projects supported by the Program are establishment of engineering proof-of-principle''; development of an instrumental prototype, method, or system; or discovery in fundamental science. Several of these project are closely associated with major strategic thrusts of the Laboratory as described in Argonne's Five Year Institutional Plan, although the scientific implications of the achieved results extend well beyond Laboratory plans and objectives. The projects supported by the Program are distributed across the major programmatic areas at Argonne. Areas of emphasis are (1) advanced accelerator and detector technology, (2) x-ray techniques in biological and physical sciences, (3) advanced reactor technology, (4) materials science, computational science, biological sciences and environmental sciences. Individual reports summarizing the purpose, approach, and results of projects are presented.

  8. Mars Science Laboratory at Sunset

    NASA Technical Reports Server (NTRS)

    2003-01-01

    December 2, 2003

    Sunset on Mars catches NASA's Mars Science Laboratory in the foreground in this artist's concept. The mission is under development for launch in 2009 and a precision landing on Mars in 2010.

    Once on the ground, the Mars Science Laboratory would analyze dozens of samples scooped up from the soil and cored from rocks as it explores with greater range than any previous Mars rover. It would investigate the past or present ability of Mars to support life. NASA is considering nuclear energy for powering the rover to give it a long operating lifespan.

    NASA's Jet Propulsion Laboratory, Pasadena, Calif., is managing development of the Mars Smart Laboratory for the NASA Office of Space Science, Washington, D.C.

  9. Mars Science Laboratory at Canyon

    NASA Technical Reports Server (NTRS)

    2003-01-01

    December 2, 2003

    NASA's Mars Science Laboratory travels near a canyon on Mars in this artist's concept. The mission is under development for launch in 2009 and a precision landing on Mars in 2010.

    Once on the ground, the Mars Science Laboratory would analyze dozens of samples scooped up from the soil and cored from rocks as it explores with greater range than any previous Mars rover. It would investigate the past or present ability of Mars to support life. NASA is considering nuclear energy for powering the rover to give it a long operating lifespan.

    NASA's Jet Propulsion Laboratory, Pasadena, Calif., is managing development of the Mars Smart Laboratory for the NASA Office of Space Science, Washington, D.C.

  10. Pre-Employment Laboratory Training

    ERIC Educational Resources Information Center

    Vela, Rene H.; Correa, Jose

    1976-01-01

    The article describes the development of a pre-employment laboratory training program in meat processing and its successful use in conjunction with a cooperative training program in a high school agriculture curriculum. (MS)

  11. National Water Quality Laboratory Profile

    USGS Publications Warehouse

    Raese, Jon W.

    1994-01-01

    The National Water Quality Laboratory determines organic and inorganic constituents in samples of surface and ground water, river and lake sediment, aquatic plant and animal material, and precipitation collected throughout the United States and its territories by the U.S. Geological Survey. In water year 1994, the Laboratory produced more than 900,000 analytical results for about 65,000 samples. The Laboratory also coordinates an extensive network of contract laboratories for the determination of radiochemical and stable isotopes and work for the U.S. Department of Defense Environmental Contamination Hydrology Program. Heightened concerns about water quality and about the possible effects of toxic chemicals at trace and ultratrace levels have contributed to an increased demand for impartial, objective, and independent data.

  12. Laboratory Techniques for the Blind

    ERIC Educational Resources Information Center

    Tombaugh, Dorothy

    1972-01-01

    Describes modifications of laboratory procedures for the BSCS Green Version biology, including dissection, microbiology, animal behavior, physiology, biochemistry, and genetics that make the methods suitable for direct experimentation by blind students. Discusses models as substitutes for microscopy. (AL)

  13. LABCON - Laboratory Job Control program

    NASA Technical Reports Server (NTRS)

    Reams, L. T.

    1969-01-01

    Computer program LABCON controls the budget system in a component test laboratory whose workload is made up from many individual budget allocations. A common denominator is applied to an incoming job, to which all effort is charged and accounted for.

  14. A Combustion Laboratory for Undergraduates.

    ERIC Educational Resources Information Center

    Peters, James E.

    1985-01-01

    Describes a combustion laboratory facility and experiments for a senior-level (undergraduate) course in mechanical engineering. The experiment reinforces basic thermodynamic concepts and provides many students with their first opportunity to work with a combustion system. (DH)

  15. A Laboratory Investigation of Groupthink.

    ERIC Educational Resources Information Center

    Courtright, John A.

    1978-01-01

    Examines the groupthink phenomenon under controlled, laboratory conditions. Results indicate that the presence or absence of disagreement (conflict, hostility) among members may be the best discriminator between groupthink and nongroupthink groups. (JMF)

  16. Instrument Synthesis and Analysis Laboratory

    NASA Technical Reports Server (NTRS)

    Wood, H. John

    2004-01-01

    The topics addressed in this viewgraph presentation include information on 1) Historic instruments at Goddard; 2) Integrated Design Capability at Goddard; 3) The Instrument Synthesis and Analysis Laboratory (ISAL).

  17. Los Alamos National Laboratory Overview

    SciTech Connect

    Neu, Mary

    2010-06-02

    Mary Neu, Associate Director for Chemistry, Life and Earth Sciences at Los Alamos National Laboratory, delivers opening remarks at the "Sequencing, Finishing, Analysis in the Future" meeting in Santa Fe, NM

  18. [Quality management in medical laboratories].

    PubMed

    Fritzer-Szekeres, M

    2010-05-01

    During the 20th century understanding for quality has changed and international and national requirements for quality have been published. Therefore also medical branches started to establish quality management systems. Quality assurance has always been important for medical laboratories. Certification according to the standard ISO 9001 and accreditation according to the standard ISO 17025 have been the proof of fulfilling quality requirements. The relatively new standard ISO 15189 is the first standard for medical laboratories. This standard includes technical and management requirements for the medical laboratory. The main focus is the proof of competence within the personnel. As this standard is accepted throughout the European Union an increase in accreditations of medical laboratories is predictable. PMID:20454753

  19. Portable Medical Laboratory Applications Software

    PubMed Central

    Silbert, Jerome A.

    1983-01-01

    Portability implies that a program can be run on a variety of computers with minimal software revision. The advantages of portability are outlined and design considerations for portable laboratory software are discussed. Specific approaches for achieving this goal are presented.

  20. Phoenix's Wet Chemistry Laboratory Units

    NASA Technical Reports Server (NTRS)

    2008-01-01

    This image shows four Wet Chemistry Laboratory units, part of the Microscopy, Electrochemistry, and Conductivity Analyzer (MECA) instrument on board NASA's Phoenix Mars Lander. This image was taken before Phoenix's launch on August 4, 2007.

    The Phoenix Mission is led by the University of Arizona, Tucson, on behalf of NASA. Project management of the mission is by NASA's Jet Propulsion Laboratory, Pasadena, Calif. Spacecraft development is by Lockheed Martin Space Systems, Denver.

  1. Gallium Safety in the Laboratory

    SciTech Connect

    Cadwallader, L.C.

    2003-05-07

    A university laboratory experiment for the US Department of Energy magnetic fusion research program required a simulant for liquid lithium. The simulant choices were narrowed to liquid gallium and galinstan (Ga-In-Sn) alloy. Safety information on liquid gallium and galinstan were compiled, and the choice was made to use galinstan. A laboratory safety walkthrough was performed in the fall of 2002 to support the galinstan experiment. The experiment has been operating successfully since early 2002.

  2. Gallium Safety in the Laboratory

    SciTech Connect

    Lee C. Cadwallader

    2003-06-01

    A university laboratory experiment for the US Department of Energy magnetic fusion research program required a simulant for liquid lithium. The simulant choices were narrowed to liquid gallium and galinstan (Ga-In-Sn) alloy. Safety information on liquid gallium and galinstan were compiled, and the choice was made to use galinstan. A laboratory safety walkthrough was performed in the fall of 2002 to support the galinstan experiment. The experiment has been operating successfully since early 2002.

  3. Misleading biochemical laboratory test results

    PubMed Central

    Nanji, Amin A.

    1984-01-01

    This article reviews the general and specific factors that interfere with the performance of common biochemical laboratory tests and the interpretation of their results. The clinical status of the patient, drug interactions, and in-vivo and in-vitro biochemical interactions and changes may alter the results obtained from biochemical analysis of blood constituents. Failure to recognize invalid laboratory test results may lead to injudicious and dangerous management of patients. PMID:6375845

  4. 42 CFR 493.1850 - Laboratory registry.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 42 Public Health 5 2012-10-01 2012-10-01 false Laboratory registry. 493.1850 Section 493.1850... (CONTINUED) STANDARDS AND CERTIFICATION LABORATORY REQUIREMENTS Enforcement Procedures § 493.1850 Laboratory... laboratories, including the following: (1) A list of laboratories that have been convicted, under Federal...

  5. 42 CFR 493.1850 - Laboratory registry.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 42 Public Health 5 2013-10-01 2013-10-01 false Laboratory registry. 493.1850 Section 493.1850... (CONTINUED) STANDARDS AND CERTIFICATION LABORATORY REQUIREMENTS Enforcement Procedures § 493.1850 Laboratory... laboratories, including the following: (1) A list of laboratories that have been convicted, under Federal...

  6. 27 CFR 22.108 - Other laboratories.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2013-04-01 2013-04-01 false Other laboratories. 22.108... Other laboratories. Laboratories, other than pathological laboratories specified in § 22.107, may... products resulting from the use of tax-free alcohol shall be confined strictly to the laboratory...

  7. 27 CFR 22.108 - Other laboratories.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2011-04-01 2011-04-01 false Other laboratories. 22.108... Other laboratories. Laboratories, other than pathological laboratories specified in § 22.107, may... products resulting from the use of tax-free alcohol shall be confined strictly to the laboratory...

  8. 27 CFR 22.108 - Other laboratories.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2012-04-01 2012-04-01 false Other laboratories. 22.108... Other laboratories. Laboratories, other than pathological laboratories specified in § 22.107, may... products resulting from the use of tax-free alcohol shall be confined strictly to the laboratory...

  9. 42 CFR 493.1850 - Laboratory registry.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 42 Public Health 5 2014-10-01 2014-10-01 false Laboratory registry. 493.1850 Section 493.1850... (CONTINUED) STANDARDS AND CERTIFICATION LABORATORY REQUIREMENTS Enforcement Procedures § 493.1850 Laboratory... laboratories, including the following: (1) A list of laboratories that have been convicted, under Federal...

  10. 42 CFR 493.1850 - Laboratory registry.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 42 Public Health 5 2011-10-01 2011-10-01 false Laboratory registry. 493.1850 Section 493.1850... (CONTINUED) STANDARDS AND CERTIFICATION LABORATORY REQUIREMENTS Enforcement Procedures § 493.1850 Laboratory... laboratories, including the following: (1) A list of laboratories that have been convicted, under Federal...

  11. 27 CFR 22.108 - Other laboratories.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2014-04-01 2014-04-01 false Other laboratories. 22.108... Other laboratories. Laboratories, other than pathological laboratories specified in § 22.107, may... products resulting from the use of tax-free alcohol shall be confined strictly to the laboratory...

  12. 42 CFR 493.1850 - Laboratory registry.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 42 Public Health 5 2010-10-01 2010-10-01 false Laboratory registry. 493.1850 Section 493.1850... (CONTINUED) STANDARDS AND CERTIFICATION LABORATORY REQUIREMENTS Enforcement Procedures § 493.1850 Laboratory... laboratories, including the following: (1) A list of laboratories that have been convicted, under Federal...

  13. 27 CFR 22.108 - Other laboratories.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Other laboratories. 22.108... Other laboratories. Laboratories, other than pathological laboratories specified in § 22.107, may... products resulting from the use of tax-free alcohol shall be confined strictly to the laboratory...

  14. 15 CFR 280.103 - Laboratory accreditation.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Laboratory accreditation. 280.103... QUALITY Petitions, Affirmations, and Laboratory Accreditation § 280.103 Laboratory accreditation. A laboratory may be accredited by any laboratory accreditation program that may be established by any entity...

  15. Lawrence Livermore National Laboratory hot spot mobile laboratory

    SciTech Connect

    Buddemeier, B

    1999-08-27

    Gross alpha/beta/tritium liquid The Hot Spot Mobile Laboratory is an asset used to analyze samples (some high hazard) from the field. Field laboratories allow the quick turnaround of samples needed to establish weapon condition and hazard assessment for the protection of responders and the public. The Hot Spot Lab is configured to fly anywhere in the world and is staffed by expert scientists and technicians from Lawrence Livermore National Laboratory who perform similar functions in their routine jobs. The Hot Spot Team carries sample control kits to provide responding field teams with the procedures, tools, and equipment for sample collection and field measurements. High-hazard samples brought back from the field are prepared for analysis in HEPA-filtered gloveboxes staffed by technicians from LLNL's Plutonium Facility. The samples are passed on to the Mobile Laboratory which carries a variety of radiological and chemical analytical equipment in portable configuration for use in the field. Equipment and personnel can also deploy special assets to local hospitals or the field for detection of plutonium in a lung or wound. Quick assessment of personnel contamination is essential for time-critical medical intervention. In addition to pulling the trailer, the Hot Spot Truck also stores some of the equipment, consumables, and a PTO generator. The Hot Spot Laboratory has the capability to be self-sufficient for several weeks when deployed to determine Pu uptake.

  16. Commercialization of a DOE Laboratory

    SciTech Connect

    Stephenson, Barry A.

    2008-01-15

    On April 1, 1998, Materials and Chemistry Laboratory, Inc. (MCLinc) began business as an employee-owned, commercial, applied research laboratory offering services to both government and commercial clients. The laboratory had previously been a support laboratory to DoE's gaseous diffusion plant in Oak Ridge (K-25). When uranium enrichment was halted at the site, the laboratory was expanded to as an environmental demonstration center and served from 1992 until 1997 as a DOE Environmental User Facility. In 1997, after the laboratory was declared surplus, it was made available to the employee group who operated the laboratory for DOE as a government-owned, contractor-operated facility. This paper describes briefly the process of establishing the business. Attributes that contributed to the success of MCLinc are described. Some attention is given to lessons learned and to changes that could facilitate future attempts to make similar transitions. Lessons learnt: as with any business venture, operation over time has revealed that some actions taken by the laboratory founders have contributed to its successful operation while others were not so successful. Observations are offered in hopes that lessons learned may suggest actions that will facilitate future attempts to make similar transitions. First, the decision to vest significant ownership of the business in the core group of professionals operating the business is key to its success. Employee-owners of the laboratory have consistently provided a high level of service to its customers while conducting business in a cost-efficient manner. Secondly, an early decision to provide business support services in-house rather than purchasing them from support contractors on site have proven cost-effective. Laboratory employees do multiple tasks and perform overhead tasks in addition to their chargeable technical responsibilities. Thirdly, assessment of technical capabilities in view of market needs and a decision to offer these

  17. Radioactive Standards Laboratory ININ as a reference laboratory in Mexico.

    PubMed

    GarcíaDíaz, O; MartínezAyala, L; HerreraValadez, L; TovarM, V; Karam, L

    2016-03-01

    The Radioactive Standards Laboratory of the National Institute of Nuclear Research is the National reference laboratory for the measurement of radioactivity in Mexico. It has a gamma-ray spectrometry system with a high-purity Ge-detector for measurements from 50 keV to 2000 keV, and develops standardized radioactive (beta-particle and gamma-ray emitting) sources in different geometries with uncertainties less than or equal to 5% for applications such as the calibration of radionuclide calibrators (clinically used dose calibrators), Ge-detectors and NaI(Tl) detectors. PMID:27358942

  18. An Atmospheric Cloud Physics Laboratory for the Space Laboratory

    NASA Technical Reports Server (NTRS)

    Smith, R.; Anderson, J.; Schrick, B.; Ellsworth, C.; Davis, M.

    1976-01-01

    Results of research and engineering analyses to date show that it is feasible to develop and fly on the first Spacelab mission a multipurpose laboratory in which experiments can be performed on the microphysical processes in atmospheric clouds. The paper presents a series of tables on the Atmospheric Cloud Physics Laboratory, with attention given to experiment classes, the preliminary equipment list (particle generators, optical and imaging devices, particle detectors and characterizers, etc.), initial equipment (scientific equipment subsystems and flight support subsystems), and scientific functional requirements (the expansion chamber, the continuous flow diffusion chamber, the static diffusion chamber, the humidifier, and particle generators).

  19. Accreditation of the PGD laboratory.

    PubMed

    Harper, J C; Sengupta, S; Vesela, K; Thornhill, A; Dequeker, E; Coonen, E; Morris, M A

    2010-04-01

    Accreditation according to an internationally recognized standard is increasingly acknowledged as the single most effective route to comprehensive laboratory quality assurance, and many countries are progressively moving towards compulsory accreditation of medical testing laboratories. The ESHRE PGD Consortium and some regulatory bodies recommend that all PGD laboratories should be accredited or working actively towards accreditation, according to the internationally recognized standard ISO 15189, 'Medical laboratories-Particular requirements for quality and competence'. ISO 15189 requires comprehensive quality assurance. Detailed management and technical requirements are defined in the two major chapters. The management requirements address quality management including the quality policy and manual, document control, non-conformities and corrective actions, continual improvement, auditing, management review, contracts, referrals and resolution of complaints. Technical requirements include personnel competence (both technical and medical), equipment, accommodation and environment, and pre-analytical, analytical and post-analytical processes. Emphasis is placed on the particular requirements of patient care: notably sample identification and traceability, test validation and interpretation and reporting of results. Quality indicators must be developed to monitor contributions to patient care and continual improvement. We discuss the implementation of ISO 15189 with a specific emphasis on the PGD laboratory, highlight elements of particular importance or difficulty and provide suggestions of effective and efficient ways to obtain accreditation. The focus is on the European environment although the principles are globally applicable. PMID:20097923

  20. 77 FR 16551 - Standards for Private Laboratory Analytical Packages and Introduction to Laboratory Related...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-03-21

    ... HUMAN SERVICES Food and Drug Administration Standards for Private Laboratory Analytical Packages and Introduction to Laboratory Related Portions of the Food Modernization Safety Act for Private Laboratory... Administration (FDA) is announcing two meetings entitled ``Standards for Private Laboratory Analytical...

  1. Virtual Laboratories and Virtual Worlds

    NASA Astrophysics Data System (ADS)

    Hut, Piet

    2008-05-01

    Since we cannot put stars in a laboratory, astrophysicists had to wait till the invention of computers before becoming laboratory scientists. For half a century now, we have been conducting experiments in our virtual laboratories. However, we ourselves have remained behind the keyboard, with the screen of the monitor separating us from the world we are simulating. Recently, 3D on-line technology, developed first for games but now deployed in virtual worlds like Second Life, is beginning to make it possible for astrophysicists to enter their virtual labs themselves, in virtual form as avatars. This has several advantages, from new possibilities to explore the results of the simulations to a shared presence in a virtual lab with remote collaborators on different continents. I will report my experiences with the use of Qwaq Forums, a virtual world developed by a new company (see http://www.qwaq.com).

  2. THE GROWTH OF A LABORATORY.

    PubMed

    EMSON, H E

    1965-07-31

    The growth of the laboratory work in a general and teaching hospital was studied from annual statistical returns, which gave a broad general picture for the period 1922 through 1953, and permitted a more detailed analysis for 1954 through 1964. An attempt was made to analyze the growth of work in the various laboratory departments, and to explain the changes found as far as possible. It appears that knowledge of previous changes might be used as a predictive tool for estimating future work loads. A plea is made for utilization of such studies in the design, equipment, staffing and financing of laboratory work, with the recognition that growth in this department has been and is likely to continue to be disproportionately greater than in hospital work as a whole. PMID:14323665

  3. Alerting of Laboratory Critical Values

    NASA Astrophysics Data System (ADS)

    Song, Sang Hoon; Park, Kyoung Un; Song, Junghan; Paik, Hyeon Young; Lee, Chi Woo; Bang, Su Mi; Hong, Joon Seok; Lee, Hyun Joo; Cho, In-Sook; Kim, Jeong Ah; Kim, Hyun-Young; Kim, Yoon

    Critical value is defined as a result suggesting that the patient is in danger unless appropriate action is taken immediately. We designed an automated reporting system of critical values and evaluated its performance. Fifteen critical values were defined and 2-4 doctors were assigned to receive short message service (SMS).Laboratory results in LIS and EMR were called back to the DIA server. The rule engine named U-brain in the CDSS server was run in real-time and decision if the laboratory data was critical was made. The CDSS system for alerting of laboratory critical values was fast and stable without additional burden to the entire EMR system. Continuous communication with clinicians and feedback of clinical performance are mandatory for the refinement and development of user-friendly CDSS contents. Appropriate clinical parameters are necessary for demonstration of the usefulness of the system.

  4. Laboratory aspects of Lyme borreliosis.

    PubMed Central

    Barbour, A G

    1988-01-01

    Lyme borreliosis (Lyme disease), a common tick-borne disorder of people and domestic animals in North America and Europe, is caused by the spirochete Borrelia burgdorferi. Following the discovery and initial propagation of this agent in 1981 came revelations that other tick-associated infectious disorders are but different forms of Lyme borreliosis. A challenge for the clinician and microbiology laboratory is confirmation that a skin rash, a chronic meningitis, an episode of myocarditis, or an arthritic joint is the consequence of B. burgdorferi infection. The diagnosis of Lyme borreliosis may be established by (i) directly observing the spirochete in host fluid or tissue, (ii) recovering the etiologic spirochete from the patient in culture medium or indirectly through inoculation of laboratory animals, or (iii) carrying out serologic tests with the patient's serum or cerebrospinal fluid. The last method, while lacking in discriminatory power, is the most efficacious diagnostic assay for most laboratories at present. Images PMID:3069200

  5. The Robotic Edge Finishing Laboratory

    SciTech Connect

    Loucks, C.S.; Selleck, C.B.

    1990-08-01

    The Robotic Edge Finishing Laboratory at Sandia National Laboratories is developing four areas of technology required for automated deburring, chamfering, and blending of machined edges: (1) the automatic programming of robot trajectories and deburring processes using information derived from a CAD database, (2) the use of machine vision for locating the workpiece coupled with force control to ensure proper tool contact, (3) robotic deburring, blending, and machining of precision chamfered edges, and (4) in-process automated inspection of the formed edge. The Laboratory, its components, integration, and results from edge finishing experiments to date are described here. Also included is a discussion of the issues regarding implementation of the technology in a production environment. 24 refs., 17 figs.

  6. Laboratory Astrophysics White Paper: Summary of Laboratory Astrophysics Needs

    NASA Technical Reports Server (NTRS)

    2002-01-01

    The NASA Laboratory Astrophysics Workshop (NASA LAW) met at NASA Ames Research Center from 1-3 May 2002 to assess the role that laboratory astrophysics plays in the optimization of NASA missions, both at the science conception level and at the science return level. Space missions provide understanding of fundamental questions regarding the origin and evolution of galaxies, stars, and planetary systems. In all of these areas the interpretation of results from NASA's space missions relies crucially upon data obtained from the laboratory. We stress that Laboratory Astrophysics is important not only in the interpretation of data, but also in the design and planning of future missions. We recognize a symbiosis between missions to explore the universe and the underlying basic data needed to interpret the data from those missions. In the following we provide a summary of the consensus results from our Workshop, starting with general programmatic findings and followed by a list of more specific scientific areas that need attention. We stress that this is a 'living document' and that these lists are subject to change as new missions or new areas of research rise to the fore.

  7. 75 FR 80011 - Good Laboratory Practice for Nonclinical Laboratory Studies

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-12-21

    ..., 1978 (43 FR 60013). As stated in its scope (Sec. 58.1), this regulation prescribes good laboratory..., sponsors have requested the ability to cite compliance with the applicable good manufacturing requirements... be required under a revised part 58, subpart F or the relevant good manufacturing requirements....

  8. Modular Laboratory Courses: An Alternative to a Traditional Laboratory Program

    ERIC Educational Resources Information Center

    Caprette, David R.; Armstrong, Sarah; Beason, K. Beth

    2005-01-01

    Our modular laboratory teaching program is characterized by two major features. First, each course is taught independently and not linked with a particular lecture course. Second, each course is designed to be completed within one-half semester or less. The modular organization has allowed incorporation of the latest technology, reduction of class…

  9. Safety in the Chemical Laboratory: A Chemical Laboratory Safety Audit.

    ERIC Educational Resources Information Center

    Reich, Arthur R.; Harris, L. E.

    1979-01-01

    Presented is an inspection form developed for use by college students to perform laboratory safety inspections. The form lists and classifies chemicals and is used to locate such physical facilities as: fume hoods, eye-wash fountains, deluge showers, and flammable storage cabinets. (BT)

  10. "Certified" Laboratory Practitioners and the Accuracy of Laboratory Test Results.

    ERIC Educational Resources Information Center

    Boe, Gerard P.; Fidler, James R.

    1988-01-01

    An attempt to replicate a study of the accuracy of test results of medical laboratories was unsuccessful. Limitations of the obtained data prevented the research from having satisfactory internal validity, so no formal report was published. External validity of the study was also limited because the systematic random sample of 78 licensed…