Science.gov

Sample records for lithium aryloxides part

  1. Structural diversity in lithium aryloxides, Part 2

    SciTech Connect

    BOYLE,TIMOTHY J.; PEDROTTY,DAWN M.; ALAM,TODD M.; VICK,SARA C.; RODRIGUEZ,MARK A.

    2000-06-06

    A series of arylalcohols [H-OAr where OAr = OC{sub 6}H{sub 5} (OPh), OC{sub 6}H{sub 4}(2-Me) (oMP), OC{sub 6}H{sub 3}(2,6-Me){sub 2} (DMP), OC{sub 6}H{sub 4}(2-Pr{prime}) (oPP), OC{sub 6}H{sub 3}(2,6-Pr{prime}){sub 2} (DIP), OC{sub 6}H{sub 4}(2-Bu{prime}) (oBP), OC{sub 6}H{sub 3}(2,6-Bu{prime}){sub 2} (DBP) where Me = CH{sub 3}, Pr{prime} = CHMe{sub 2}, and Bu{prime} = CMe{sub 3}] were reacted with LiN(SiMe{sub 3}){sub 2} in pyridine (py) to generate the appropriate ``Li(OAr)(py){sub x}'' complex. The resultant products were characterized by single crystal X-ray diffraction as: [Li(OPh)(py){sub 2}]{sub 2} (1), [Li(oMP)(py){sub 2}]{sub 2} (2), [Li(DMP)(py){sub 2}]{sub 2} (3), [Li(oPP)(py){sub 2}]{sub 2} (4), [Li(DIP)(py){sub 2}]{sub 2} (5), [Li(oBP)(py){sub 2}]{sub 2} (6), and [Li(DBP)(py)]{sub 2} (7). Compounds 1--6 adopt a dinuclear, edge-shared tetrahedral complex. For 7, due to the steric crowding of the DBP ligand, only one py is coordinated yielding a dinuclear fused trigonal planar arrangement. Two additional structure types were also characterized for the DIP ligand as [Li(DIP)(H-DIP)(py)]{sub 2} (5b) and [Li{sub 2}(DIP){sub 2}(py){sub 3}] (5c). {sup 6,7}Li and {sup 13}C NMR solid state MAS spectroscopy indicated that the bulk powder was consistent with the crystalline material. Solution state NMR spectroscopy revealed a symmetric molecule existed in solution for 1--7.

  2. Synthesis and Structural Characterization of Lithium and Titanium Complexes Bearing a Bulky Aryloxide Ligand Based on a Rigid Fused-Ring s-Hydrindacene Skeleton.

    PubMed

    Kanazawa, Shoya; Ohira, Taishi; Goda, Shun; Hayakawa, Naoki; Tanikawa, Tomoharu; Hashizume, Daisuke; Ishida, Yutaka; Kawaguchi, Hiroyuki; Matsuo, Tsukasa

    2016-07-01

    The bulky aryl alcohols, (Rind)OH (1) [Rind = EMind (a) and Eind (b)], based on the rigid fused-ring 1,1,3,3,5,5,7,7-octa-R-substituted s-hydrindacene skeleton were prepared by the reaction of (Rind)Li with nitrobenzene followed by protonation. The treatment of 1 with (n)BuLi affords the lithium aryloxide dimers [(Rind)OLi(THF)]2 (2) or trimers [(Rind)OLi]3 (3), depending on the employed solvents (THF = tetrahydrofuran). The salt metathesis reaction of [(EMind)OLi(THF)]2 (2a) with TiCl4(THF)2 leads to the formation of the mononuclear diamagnetic mono- and bis(aryloxide) Ti(IV) complexes, [(EMind)O]TiCl3(THF) (4a) and [(EMind)O]2TiCl2 (5a). We also isolated a trace amount of the tris(aryloxide) Ti(IV) complex, [(EMind)O]3TiCl (6a). The reaction between 2a and TiCl3(THF)3 resulted in the isolation of the mononuclear paramagnetic mono- and bis(aryloxide) Ti(III) complexes, [(EMind)O]TiCl2(THF)2 (7a) and [(EMind)O]2TiCl(THF)2 (8a). The discrete monomeric structures of the titanium complexes 4a, 5a, 6a, 7a, and 8a were determined by X-ray crystallography. PMID:27284975

  3. Solvent Influences on the Molecular Aggregation of Magnesium Aryloxides

    SciTech Connect

    ZECHMANN,CECILIA A.; BOYLE,TIMOTHY J.; RODRIGUEZ,MARK A.; KEMP,RICHARD A.

    2000-07-14

    Magnesium aryloxides were prepared in a variety of solvents through the reaction of dibutyl magnesium with sterically varied aryl alcohols: 2,6-dimethylphenol (H-DMP), 2,6-diisopropylphenol (H-DIP), and 2,4,6-trichlorophenol (H-TCP). Upon using a sufficiently strong Lewis-basic solvent, the monomeric species Mg(DMP){sub 2}(py){sub 3} (1, py = pyridine), Mg(DIP){sub 2}(THF){sub 3}, (2a, THF = tetrahydrofuran) Mg(TCP){sub 2}(THF){sub 3} (3) were isolated. Each of these complexes possesses a five-coordinate magnesium that adopts a trigonal bipyramidal geometry. In the absence of a Lewis base, the reaction with H-DIP yields a soluble trinuclear complex, [Mg(DIP){sub 2}]{sub 3} (2b). The Mg metal centers in 2b adopt a linear arrangement with a four-coordinate central metal while the outer metal centers are reduced to just three-coordinate. Solution spectroscopic methods suggest that while 2b remains intact, the monomeric species (1, 2a, and 3) are involved in equilibria, which facilitate intermolecular ligand transfer.

  4. Oxidation chemistry of a uranium(III) aryloxide

    SciTech Connect

    Avens, L.R.; Barnhart, D.M.; Burns, C.J.

    1994-09-14

    The oxidation chemistry of the uranium(III) aryloxide complex U(OAr){sub 3} (OAr=2,6-di-tert-butylphenoxide) has been explored with a variety of one-electron oxidants. Oxidation of U(OAr){sub 3} with either AgBF{sub 4} or AgPF{sub 6} produces the uranium(IV) fluoride FU(OAr){sub 3}, 1. The analogous chloride compound, ClU(OAr){sub 3}, 2, is prepared by reaction with either benzyl chloride or PCl{sub 5}. Oxidation by AgBr, CBr{sub 4} or PBr{sub 5} yields BrU(OAr){sub 3}, 3. Oxidation of U(OAr){sub 3} by elemental iodine yields IU(OAr){sub 3}, 4. Compound 4 crystallizes in the space group P2{sub 1}/n, with unit cell dimensions a = 20.005(6) {angstrom}, b = 10.228(4) {angstrom}, {beta} = 115.30(2){degrees}, V = 4047(2) {angstrom}{sup 3}, and Z = 4. Oxidation of U(OAr){sub 3} with CI{sub 4} (carbon tetraiodide) does not yield 4 but rather gives rise to I{sub 2}U(OAr){sub 2}, 5. Orthorhombic crystals of the THF adduct I{sub 2}U(OAr){sub 2}(THF) were obtained from THF/hexane. I{sub 2}U(OAr){sub 2}(THF) crystallizes in the space group Pbca, with unit cell dimensions a = 18.197(2) {angstrom}, b = 17.866(2) {angstrom}, c = 20.930(3) {angstrom}, V = 6804.5(14) {angstrom}{sup 3}, and Z = 8. The chalcogenide-bridged compounds (ArO){sub 3}U-O-U(OAr){sub 3}, 6, and (ArO){sub 3}U-S-U-(OAr){sub 3}, 7, can be prepared by reaction with a variety of chalogen-donor reagents with either COS or Ph{sub 3}P=S affords 7. Compound 7 crystallizes as a diethyl ether solvate in the space group P{bar 1}, with unit cell dimensions a = 13.290(3) {angstrom}, b = 13.744(4) {angstrom}, c = 14.643(5) {angstrom}, {alpha} = 81.41(2){degrees}, {beta} = 65.36(2){degrees}, {gamma}=67.58(2){degrees}, V = 2247.4-(11) {angstrom}{sup 3}, and Z=1. Oxidation of U(OAr){sub 3} by molecular oxygen does not result in the isolation of the oxobridged dinuclear species but in the formation of the known uranium(IV) compound U(OAr){sub 4} by ligand redistribution.

  5. Lithium

    USGS Publications Warehouse

    Jaskula, B.W.

    2011-01-01

    In 2010, lithium consumption in the United States was estimated to have been about 1 kt (1,100 st) of contained lithium, a 23-percent decrease from 2009. The United States was estimated to be the fourth largest consumer of lithium. It remained the leading importer of lithium carbonate and the leading producer of value-added lithium materials. Only one company, Chemetall Foote Corp. (a subsidiary of Chemetall GmbH of Germany), produced lithium compounds from domestic resources. In 2010, world lithium consumption was estimated to have been about 21 kt (22,000 st) of lithium contained in minerals and compounds, a 12-percent increase from 2009.

  6. Lithium

    USGS Publications Warehouse

    Jaskula, B.W.

    2010-01-01

    In 2009, lithium consumption in the United States was estimated to have been about 1.2 kt (1,300 st) of contained lithium, a 40-percent decrease from 2008. The United States was estimated to be the fourth largest consumer of lithium, and remained the leading importer of lithium carbonate and the leading producer of value-added lithium materials. Only one company, Chemetall Foote Corp. (a subsidiary of Chemetall GmbH of Germany), produced lithium compounds from domestic resources. In 2009, world lithium consumption was estimated to have been about 18.7 kt (20,600 st) of lithium contained in minerals and compounds.

  7. Lithium

    USGS Publications Warehouse

    Jaskula, B.W.

    2012-01-01

    In 2011, world lithium consumption was estimated to have been about 25 kt (25,000 st) of lithium contained in minerals and compounds, a 10-percent increase from 2010. U.S. consumption was estimated to have been about 2 kt (2,200 st) of contained lithium, a 100-percent increase from 2010. The United States was estimated to be the fourth-ranked consumer of lithium and remained the leading importer of lithium carbonate and the leading producer of value-added lithium materials. One company, Chemetall Foote Corp. (a subsidiary of Chemetall GmbH of Germany), produced lithium compounds from domestic brine resources near Silver Peak, NV.

  8. Lithium

    USGS Publications Warehouse

    Ober, J.A.

    2006-01-01

    In 2005, lithium consumption in the United States was at 2.5 kt of contained lithium, nearly 32% more than the estimate for 2004. World consumption was 14.1 kt of lithium contained in minerals and compounds in 2003. Exports from the US increased slightly compared with 2004. Due to strong demand for lithium compounds in 2005, both lithium carbonate plants in Chile were operating at or near capacity.

  9. Is violence in part a lithium deficiency state?

    PubMed

    Goldstein, Mark R; Mascitelli, Luca

    2016-04-01

    Violence, particularly firearm violence, leading to suicide and homicide is a significant problem worldwide. A majority of suicidal and homicidal violence involves males; homicidal violence is prevalent among young men and suicide is the leading cause of violence worldwide. Lithium, in pharmacological doses, has been used successfully for decades in treating bipolar disorders, and has been shown to decrease violent crime in this situation. Interestingly, lithium, in trace amounts, as occurs in some drinking water, has been inversely related to aggression, and suicidal and homicidal violence. Lithium is naturally found in vegetables, grains and drinking water, and dietary intake varies from nearly zero to 3mg daily. Elemental lithium, in trace doses, has been shown to improve mood in weeks. Moreover, lithium, in trace amounts, has no toxicity. In order to ensure adequate dietary intakes of elemental lithium daily for the purpose of decreasing aggression and violence, we propose considering the fortification of cereal grain products with lithium and also the addition of lithium to vitamin preparations for adults. Importantly, randomized trials in various populations are needed to test this hypothesis. PMID:26968907

  10. Lithium

    USGS Publications Warehouse

    Ober, J.

    1998-01-01

    The lithium industry can be divided into two sectors: ore concentrate producers and chemical producers. Ore concentrate producers mine lithium minerals. They beneficiate the ores to produce material for use in ceramics and glass manufacturing.

  11. 10 CFR Appendix N to Part 110 - Illustrative List of Lithium Isotope Separation Facilities, Plants and Equipment Under NRC's...

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 10 Energy 2 2013-01-01 2013-01-01 false Illustrative List of Lithium Isotope Separation Facilities... Appendix N to Part 110—Illustrative List of Lithium Isotope Separation Facilities, Plants and Equipment Under NRC's Export Licensing Authority a. Facilities or plants for the separation of lithium isotopes....

  12. 10 CFR Appendix N to Part 110 - Illustrative List of Lithium Isotope Separation Facilities, Plants and Equipment Under NRC's...

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 10 Energy 2 2012-01-01 2012-01-01 false Illustrative List of Lithium Isotope Separation Facilities... Appendix N to Part 110—Illustrative List of Lithium Isotope Separation Facilities, Plants and Equipment Under NRC's Export Licensing Authority a. Facilities or plants for the separation of lithium isotopes....

  13. 10 CFR Appendix N to Part 110 - Illustrative List of Lithium Isotope Separation Facilities, Plants and Equipment Under NRC's...

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 10 Energy 2 2014-01-01 2014-01-01 false Illustrative List of Lithium Isotope Separation Facilities... Appendix N to Part 110—Illustrative List of Lithium Isotope Separation Facilities, Plants and Equipment Under NRC's Export Licensing Authority a. Facilities or plants for the separation of lithium isotopes....

  14. 10 CFR Appendix N to Part 110 - Illustrative List of Lithium Isotope Separation Facilities, Plants and Equipment Under NRC's...

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 10 Energy 2 2011-01-01 2011-01-01 false Illustrative List of Lithium Isotope Separation Facilities... Appendix N to Part 110—Illustrative List of Lithium Isotope Separation Facilities, Plants and Equipment Under NRC's Export Licensing Authority a. Facilities or plants for the separation of lithium isotopes....

  15. 10 CFR Appendix N to Part 110 - Illustrative List of Lithium Isotope Separation Facilities, Plants and Equipment Under NRC's...

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Illustrative List of Lithium Isotope Separation Facilities... Appendix N to Part 110—Illustrative List of Lithium Isotope Separation Facilities, Plants and Equipment Under NRC's Export Licensing Authority a. Facilities or plants for the separation of lithium isotopes....

  16. Lithium

    MedlinePlus

    ... bipolar disorder (manic-depressive disorder; a disease that causes episodes of depression, episodes of mania, and other abnormal moods). Lithium ... Lithium is also sometimes used to treat depression, schizophrenia (a mental ... emotions), disorders of impulse control (inability to resist the urge ...

  17. Protonation at the aromatic ring vs at the carbonyl group of lanthanide-diaryl ketone dianion species by aryl alcohols. Formation, structural characterization, and reactivity of lanthanide aryloxide, mixed aryloxide/alkoxide, and aryloxide/enolate complexes

    SciTech Connect

    Yoshimura, Takashi; Hou, Z.; Wakatsuki, Yasua

    1995-11-01

    Reaction of the ytterbium-benzophenone dianion complex (1), which was formed by reaction of Yb metal with benzophenone in THF/HMPA, with 2,6-di-tert-butyl-4-methylphenol, yielded the ytterbium(II) aryloxide complex Yb(OAr){sub 2}(HMPA){sub 2} (2, Ar= C{sub 6}H{sub 2} -{sup t}Bu{sub 2}-2,6-Me-4) as a major product (80%) and the ytterbium(III) enolate complex (3) as a minor one (ca. 5% yield). The mechanisms of these reactions are discussed. X-ray crystallographic studies reveal that 3, 4a, and 7b are isostructural, and so are 5a and 6. The central metal ions in these complexes are all five-coordinated in a trigonal bipyramid form (highly distorted in the case of 5a and 6) with two HMPA ligands at the apical and three anionic oxygen ligands at the equatorial positions. 25 refs., 7 figs., 7 tabs.

  18. New mechanism for the ring-opening polymerization of lactones? Uranyl aryloxide-induced intermolecular catalysis.

    PubMed

    Walshe, Aurora; Fang, Jian; Maron, Laurent; Baker, Robert J

    2013-08-01

    The uranyl aryloxide [UO2(OAr)2(THF)2] (Ar = 2,6-(t)Bu2-C6H2) is an active catalyst for the ring-opening cyclo-oligomerization of ε-caprolactone and δ-valerolactone but not for β-butyrolactone, γ-butyrolactone, and rac-lactide. (1)H EXSY measurements give the thermodynamic parameters for exchange of monomer and coordinated THF, and rates of polymerization have been determined. A comprehensive theoretical examination of the mechanism is discussed. From both experiment and theory, the initiation step is intramolecular and in keeping with the accepted mechanism, while computational studies indicate that propagation can go via an intermolecular pathway, which is the first time this has been observed. The lack of polymerization for the inactive monomers has been investigated theoretically and C-H···π interactions stabilize the coordination of the less rigid monomers. PMID:23879703

  19. Uranium(III) complexes with bulky aryloxide ligands featuring metal-arene interactions and their reactivity toward nitrous oxide.

    PubMed

    Franke, Sebastian M; Tran, Ba L; Heinemann, Frank W; Hieringer, Wolfgang; Mindiola, Daniel J; Meyer, Karsten

    2013-09-16

    We report the synthesis and use of an easy-to-prepare, bulky, and robust aryloxide ligand starting from inexpensive precursor materials. Based on this aryloxide ligand, two reactive, coordinatively unsaturated U(III) complexes were prepared that are masked by a metal-arene interaction via δ-backbonding. Depending on solvent and uranium starting material, both a tetrahydrofuran (THF)-bound and Lewis-base-free U(III) precursor can easily be prepared on the multigram scale. The reaction of these trivalent uranium species with nitrous oxide, N2O, was studied and an X-ray diffraction (XRD) study on single crystals of the product revealed the formation of a five-coordinate U(V) oxo complex with two different molecular geometries, namely, square pyramidal and trigonal bipyramidal. PMID:23987649

  20. Lithium

    MedlinePlus

    ... mania (frenzied, abnormally excited mood) in people with bipolar disorder (manic-depressive disorder; a disease that causes episodes of depression, episodes of mania, and other abnormal moods). Lithium is in a ... antimanic agents. It works by decreasing abnormal activity in the brain.

  1. Application of the homogeneous oxidation of alkanes: Synthesis and characterization of metal complexes of a linked aryloxide

    NASA Astrophysics Data System (ADS)

    Gordon, Benjamin Willis Franklin

    Methane is the main component of natural gas, largely left behind due to cost of transportation. There are vast stores of natural gas outweighing the known reserves of liquid petroleum. A chemical process by which methane can be transformed into a usable transportable product is very important. The selective transformation of methane into a transportable product, such as methanol or formaldehyde, would be a large step forward in utilizing a vast resource. Research on transforming methane selectively has been met with several obstacles based on poor conversion and selectivity. Several methods exist for transforming methane to methanol or formaldehyde through heterogeneous metal catalyzed oxidation. Currently, these metal catalyzed processes are energy intensive and result in low conversion and selectivity. Methanol, the desired product, tends to react preferentially. In many cases, methanol is transformed to another product at a fast rate before recovery. This work describes new techniques for preventing the over oxidation using a homogeneous catalyst system under mild temperature conditions and employing solvents that react with methanol. The solvent effectively removes methanol in a reversible process protecting it from further oxidation. The selective oxidation of higher weight alkanes, such as propane and butane, is also discussed where unusual primary carbon selectivity is observed. The transition metal atoms, tantalum and niobium, have received attention for the interesting chemical reactions, such as metathesis and living polymerization, that they are known to mediate. Aryloxide complexes of these metals undergo unusual chemical transformations especially in the presence of bulky ligand substituents. This work describes the synthesis and characterization of tantalum and niobium complexes of a linked aryloxide ligand. The metal complexes of this ligand are unusual and this dissertation provides the foundation for important future studies of the complexes of

  2. Synthesis and structures of niobium(V) complexes stabilized by linear-linked aryloxide trimers.

    PubMed

    Matsuo, Tsukasa; Kawaguchi, Hiroyuki

    2002-11-18

    The preparation and characterization of a series of niobium(V) complexes that incorporate the linear-linked aryloxide trimers 2,6-bis(4,6-dimethylsalicyl)-4-tert-butylphenol [H3(Me-L)] and 2,6-bis(4-methyl-6-tert-butylsalicyl)-4-tert-butylphenol [H3(tBu-L)] are described. The chloride complex [Nb(Me-L)Cl2]2 (1) was prepared in high yield by reaction of NbCl5 with H3(Me-L) in toluene. In contrast, the analogous reaction with H3(tBu-L) gave a mixture of [Nb(tBu-L)Cl2]2 (2) and [Nb(de-tBu-L)Cl2]2 (3a). During the formation of 3a, one of tert-butyl groups at the ortho position in the tBu-L ligand was lost. When the NbCl5/H3(tBu-L) reaction was carried out in acetonitrile, Nb[H(tBu-L)]Cl3(NCMe) (4) was obtained. Heating a solution of 4 in toluene generated 2 and 3a. The isolated complex 4 underwent ligand redistribution in acetonitrile to produce Nb[H(tBu-L)]2Cl(NCMe) (5). Treatment of NbCl5 with Li3(tBu-L) in toluene afforded 2. The chloride ligands in 1 and 2 smoothly reacted with 4 equiv of MeMgI and LiStBu, resulting in [Nb(R-L)Me2]2 [R = Me (6), tBu (7)] and Nb(Me-L)(StBu)2 (8), respectively. A number of the above complexes have been characterized by X-ray crystallography. In the structures of 1, 2, and 6, the R-L ligand is bound to the metal center with a U-coordination mode, while an alternative S-conformation is adopted for 3a and 8. Complexes 4 and 5 contain a bidentate H(tBu-L) diphenoxide-monophenol ligand. PMID:12425637

  3. Bridged bis(amidinate) lanthanide aryloxides: syntheses, structures, and catalytic activity for addition of amines to carbodiimides.

    PubMed

    Tu, Jing; Li, Wenbo; Xue, Mingqiang; Zhang, Yong; Shen, Qi

    2013-04-28

    Various lanthanide aryloxide complexes supported by bridged bis(amidinate) ligand L, LLnOAr(DME) (L = Me3SiNC(Ph)N(CH2)3NC(Ph)NSiMe3, DME = dimethoxyethane, Ln = Y, Ar = 2,6-(Me)2C6H3 (1), 2,6-((i)Pr)2C6H3 (2), 2,6-((t)Bu)2-4-(Me)C6H2 (3); Ar = 2,6-((t)Bu)2-4-(Me)C6H2, Ln = Nd (4), Sm (5), Yb (6)) were synthesized, and complexes 1, 2 and 4–6 were characterized by single crystal X-ray diffraction. All the complexes are efficient precatalysts for catalytic addition of amines to carbodiimides. The catalytic activity is influenced by lanthanide metals and the aryloxide groups (Nd (4) Sm (5) < Y (3) Yb (6) and -2,6-(Me)2C6H3 < -2,6-((i)Pr)2C6H3 < -2,6-((t)Bu)2-4-(Me)C6H2). The catalytic addition reaction with 3 showed a good scope of substrates. The mechanism investigation revealed the real active intermediate being the monoguanidinate complexes supported by an aryloxide and an amidine-functionalized amidinate group, L′Ln[O2,6-((t)Bu)2-4-(Me)C6H2][RNCNHRN(Ar′)] (L′ = Me3SiNHC(Ph)N(CH2)3NC(Ph)NSiMe3, R = (i)Pr, Ar′ = phenyl, Ln = Yb (8), Y (11); R = Cy, Ar′ = phenyl, Ln = Yb (10), Y (12); R = (i)Pr, Ar′ = 4-ClC6H4, Ln = Yb (9)), which were isolated from the reactions of 6 (or 3) with amine and carbodiimide in a molar ratio of 1:1:1 and structurally characterized. The Ln-active group in the present precatalyst is a Ln–amidinate species, not the Ln–OAr group. PMID:23459864

  4. Zirconium Hydride Complex Supported by a Tetradentate Carbon-Centered Tripodal Tris(aryloxide) Ligand: Synthesis, Structure, and Reactivity.

    PubMed

    Nakanishi, Yusuke; Ishida, Yutaka; Kawaguchi, Hiroyuki

    2016-04-18

    A dizirconium trihydride complex supported by a tetradentate carbon-centered tris(aryloxide) ligand [{Na(dme)}3{(O3C)Zr}2(μ-H)3] (2; [O3C] = [(3,5-(t)Bu2-2-O-C6H2)3C](4-)) was prepared by reacting [(O3C)Zr(thf)3] (1) with NaBHEt3 in toluene. Exposure of 2 in THF to CO2 (1 atm) resulted in facile insertion of CO2 into Zr-H bonds, yielding a formate complex [{Na(thf)2}3{(O3C)Zr}2(μ-O2CH)3] (3). Treatment of 2 with P4 in toluene led to formation of [Na(thf)5][{Na(thf)2}2{(O3C)Zr}2(μ-P3)] (4) and PH3, in which hydrogenation of P4 took place. Complex 2 reacted with Me3SiN3 to afford an azide-bridged cyclotrimer [{Na(thf)2}{(O3C)ZrN3(thf)}]3 (5) with concomitant liberation of Me3SiH. The molecular structures of these complexes 2-5 have been determined by X-ray diffraction analyses. PMID:27045559

  5. Bis(phosphinic)diamido yttrium amide, alkoxide, and aryloxide complexes: an evaluation of lactide ring-opening polymerization initiator efficiency.

    PubMed

    Platel, Rachel H; White, Andrew J P; Williams, Charlotte K

    2011-08-15

    The synthesis and characterization of a series of bis(phosphinic)diamido yttrium alkoxide, amide, and aryloxide initiators are reported. The new complexes are characterized using multinuclear nuclear magnetic resonance (NMR) spectroscopy, elemental analysis, and, in some cases, X-ray crystallography. The alkoxide complexes are all dimeric in both the solid state and in solution, as are the amide complexes substituted with iso-propyl or phenyl groups on the phosphorus atoms. On the other hand, increasing the steric hindrance of the phosphorus substituents (tert-butyl), enables isolation of mononuclear yttrium amide complexes with either 2,2-dimethylpropylene or ethylene diamido ligand backbones. The complex of 2,6-di-tert-butyl-4-methylphenoxide is also mononuclear. All the new complexes are efficient initiators for rac-lactide ring-opening polymerization. The polymerization kinetics are compared and pseudo first order rate constants, k(obs), determined. The polymerization control is also discussed, by monitoring the number-averaged molecular weight, M(n), and polydispersity index, PDI, obtained using gel permeation chromatography (GPC). The alkoxide complexes are the most efficient initiators, showing very high rates and good polymerization control, behavior consistent with rapid rates of initiation. The phenoxide and amide complexes are less efficient as manifest by nonlinear regions in the kinetic plots, lower values for k(obs), and reduced polymerization control. One of the mononuclear yttrium amide complexes shows heteroselectivity in the polymerization of rac-lactide; however, this effect is reduced on changing the initiating group to phenoxide or on changing the ancillary ligand diamido backbone group. PMID:21749161

  6. Layered manganese oxide intergrowth electrodes for rechargeable lithium batteries: Part 1-substitution with Co or Ni

    SciTech Connect

    Dolle, Mickael; Patoux, Sebastien; Doeff, Marca M.

    2004-09-08

    Lithium manganese oxides substituted with nickel or cobalt were characterized electrochemically in lithium cell configurations. The compounds studied were either single-phase layered structures with either primarily O2 or O3 stacking arrangements, or O2/O3 intergrowths, prepared from P2, P3 and P2/P3 sodium-containing precursors, respectively. The stacking arrangements are extremely sensitive to the Na/T. M. (T. M. = transition metal) ratios and the level of substitution. Phase diagrams showing the stability regions of the various arrangements for the Na-Ni-Mn-O system are presented. A possible correlation between vacancies and electrochemical performance is suggested. For high levels of substitution with Ni, fewer defects are possible for materials containing more O3 component and higher discharge capacities can be achieved, but spinel conversion upon cycling also occurs more rapidly as the O3 content increases. Intergrowths show intermediate behavior and represent a potential route towards designing stable, high capacity electrodes.

  7. Low-temperature charging of lithium-ion cells part I: Electrochemical modeling and experimental investigation of degradation behavior

    NASA Astrophysics Data System (ADS)

    Tippmann, Simon; Walper, Daniel; Balboa, Luis; Spier, Bernd; Bessler, Wolfgang G.

    2014-04-01

    Fast charge of Li-ion cells is one of the main challenges in automotive battery application. As a particular problem at low temperatures and high charging rates, lithium deposits as metal on the anode surface (so-called lithium plating) instead of intercalation. Electrochemical models help to understand internal processes and predict aging effects, which finally lead to optimized charging strategies. In this work, a 1D + 1D (pseudo-2D) electrochemical model is developed, applied over a wide range of temperature (T = -25 °C to 40 °C) and current (I = 0.1 C to 6 C), and coupled with a 0D thermal model. The model is parameterized with measurement data in frequency domain using electrochemical impedance spectroscopy (EIS) and validated with time-domain data. In experiments cells are charged under different operating conditions. Capacity fade is measured after a significant number of cycles and compared to the simulated anode potential. A qualitative correlation is found between the degradation in experiment and the anode potential dropping below 0 V vs. Li/Li+ at the separator-anode boundary in the simulation. Furthermore a semi-quantitative expression for degradation is introduced. The transformation of the model into an on-board applicable form is presented in the companion contribution (part II).

  8. Layered manganese oxide intergrowth electrodes for rechargeable lithium batteries: Part 2. Substitution with Al

    SciTech Connect

    Patoux, Sebastien; Dolle, Mickael; Doeff, Marca M.

    2004-09-08

    The structural and electrochemical characterization of layered Li{sub x}Al{sub y}Mn{sub 1-y}O{sub 2} compounds prepared from sodium-containing precursors is described. A quaternary phase diagram showing composition ranges for pure P2 and P3 structures and P2/P3 intergrowths obtained in the Na-Al-Mn-O system is presented. Upon ion exchange, these compounds change to O2, O3 or O2/O3 stacking arrangements, respectively. The oxygen array in O3 and spinel structures is similar, and most of the O3 structures convert to spinel rapidly upon electrochemical cycling in lithium cells. This process is delayed somewhat by increased Al substitution, but not completely inhibited. More effective suppression of the phase transformation is observed in O2/O3 intergrowth electrodes. Additionally, the capacity retention upon cycling and the rate behavior of cells containing intergrowth electrodes is superior to those with pure O2 structures.

  9. Lithium: updated human knowledge using an evidence-based approach. Part II: Clinical pharmacology and therapeutic monitoring.

    PubMed

    Grandjean, Etienne Marc; Aubry, Jean-Michel

    2009-01-01

    After a single dose, lithium, usually given as carbonate, reaches a peak plasma concentration at 1.0-2.0 hours for standard-release dosage forms, and 4-5 hours for sustained-release forms. Its bioavailability is 80-100%, its total clearance 10-40 mL/min and its elimination half-life is 18-36 hours. Use of the sustained-release formulation results in 30-50% reductions in peak plasma concentrations without major changes in the area under the plasma concentration curve. Lithium distribution to the brain, evaluated using 7Li magnetic resonance spectroscopy, showed brain concentrations to be approximately half those in serum, occasionally increasing to 75-80%. Brain concentrations were weakly correlated with serum concentrations. Lithium is almost exclusively excreted via the kidney as a free ion and lithium clearance is considered to decrease with aging. No gender- or race-related differences in kinetics have been demonstrated. Renal insufficiency is associated with a considerable reduction in renal clearance of lithium and is considered a contraindication to its use, especially if a sodium-poor diet is required. During the last months of pregnancy, lithium clearance increases by 30-50% as a result of an increase in glomerular filtration rate. Lithium also passes freely from maternal plasma into breast milk. Numerous kinetic interactions have been described for lithium, usually involving a decrease in the drug's clearance and therefore increasing its potential toxicity. Clinical pharmacology studies performed in healthy volunteers have investigated a possible effect of lithium on cognitive functions. Most of these studies reported a slight, negative effect on vigilance, alertness, learning and short-term memory after long-term administration only. Because of the narrow therapeutic range of lithium, therapeutic monitoring is the basis for optimal use and administration of this drug. Lithium dosages should be adjusted on the basis of the serum concentration drawn

  10. Lithium overdosage and related tests.

    PubMed

    Pigatto, Paolo D; Dell'Osso, Bernardo; Guzzi, Gianpaolo

    2016-12-01

    Lithium acts biochemically through the inositol depletion in brain cortex. At low doses, however, it is partly effective and/or ineffective, whereas in high concentrations is toxic. We would like to make one point about this review. In fact, in our view, the patient should be given a support to correct hypernatremia and even sodium levels should be tested serially-along with serum lithium concentrations-because high sodium levels reduce the rate of elimination of lithium. Lithium is mainly a neurotoxicant. Lithium-related central nervous system toxicity as well as the cardiovascular and thyroid changes are most likely due to the cations (Na2 (+) and K(+)) competition. PMID:26753697

  11. Bismuth Coordination Chemistry with Allyl, Alkoxide, Aryloxide, and Tetraphenylborate Ligands and the {[2,6-(Me2NCH2)2C6H3]2Bi}+ Cation

    SciTech Connect

    Ian J. Casely; Joseph W. Ziller; Bruce J. Mincher; William J. Evans

    2011-02-01

    A series of bis(aryl) bismuth compounds containing (N,C,N)-pincer ligands, [2,6-(Me2NCH2)2C6H3]1- (Ar'), have been synthesized and structurally characterized to compare the coordination chemistry of Bi3+ with similarly-sized lanthanide ions, Ln3+. Treatment of Ar'2BiCl, 1, with ClMg(CH2CH=CH2) affords the allyl complex Ar'2Bi(?1-CH2CH=CH2), 2, in which only one carbon coordinates to bismuth. Complex 1 reacts with KOtBu and KOC6H3-2,6-Me2 to yield the alkoxide Ar'2Bi(OtBu), 3, and aryloxide Ar'2Bi(OC6H3-2,6-Me2), 4, respectively, but the analogous reaction with the sterically crowded KOC6H3-2,6-tBu2 forms [Ar'2Bi][OC6H3-2,6-tBu2], 6, in which the aryloxide ligand acts as an outer sphere anion. Chloride is removed from 1 by NaBPh4 to form [Ar'2Bi][BPh4], 5, which crystallizes from THF in an unsolvated form with tetraphenylborate as an outer sphere counteranion.

  12. Characterization of high-power lithium-ion cells during constant current cycling. Part I. Cycle performance and electrochemical diagnostics

    SciTech Connect

    Shim, Joongpyo; Striebel, Kathryn A.

    2003-01-24

    Twelve-cm{sup 2} pouch type lithium-ion cells were assembled with graphite anodes, LiNi{sub 0.8}Co{sub 0.15}Al{sub 0.05}O{sub 2} cathodes and 1M LiPF{sub 6}/EC/DEC electrolyte. These pouch cells were cycled at different depths of discharge (100 percent and 70 percent DOD) at room temperature to investigate cycle performance and pulse power capability. The capacity loss and power fade of the cells cycled over 100 percent DOD was significantly faster than the cell cycled over 70 percent DOD. The overall cell impedance increased with cycling, although the ohmic resistance from the electrolyte was almost constant. From electrochemical analysis of each electrode after cycling, structural and/or impedance changes in the cathode are responsible for most of the capacity and power fade, not the consumption of cycleable Li from side-reactions.

  13. Hydrogen, lithium, and lithium hydride production

    SciTech Connect

    Brown, Sam W; Spencer, Larry S; Phillips, Michael R; Powell, G. Louis; Campbell, Peggy J

    2014-03-25

    A method of producing high purity lithium metal is provided, where gaseous-phase lithium metal is extracted from lithium hydride and condensed to form solid high purity lithium metal. The high purity lithium metal may be hydrided to provide high purity lithium hydride.

  14. Lithium nephrotoxicity.

    PubMed

    Azab, Abed N; Shnaider, Alla; Osher, Yamima; Wang, Dana; Bersudsky, Yuly; Belmaker, R H

    2015-12-01

    Reports of toxic effects on the kidney of lithium treatment emerged very soon after lithium therapy was introduced. Lithium-induced nephrogenic diabetes insipidus is usually self-limiting or not clinically dangerous. Some reports of irreversible chronic kidney disease and renal failure were difficult to attribute to lithium treatment since chronic kidney disease and renal failure exist in the population at large. In recent years, large-scale epidemiological studies have convincingly shown that lithium treatment elevates the risk of chronic kidney disease and renal failure. Most patients do not experience renal side effects. The most common side effect of polyuria only weakly predicts increasing creatinine or reduced kidney function. Among those patients who do experience decrease in creatinine clearance, some may require continuation of lithium treatment even as their creatinine increases. Other patients may be able to switch to a different mood stabilizer medication, but kidney function may continue to deteriorate even after lithium cessation. Most, but not all, evidence today recommends using a lower lithium plasma level target for long-term maintenance and thereby reducing risks of severe nephrotoxicity. PMID:26043842

  15. Evaluation of commercial lithium-ion cells based on composite positive electrode for plug-in hybrid electric vehicle applications. Part I: Initial characterizations

    SciTech Connect

    Matthieu Dubarry; Cyril Truchot; Mikael Cugnet; Bor Yann Liaw; Kevin Gering; Sergiy Sazhin; David Jamison; Christopher Michelbacher

    2011-12-01

    Evaluating commercial Li-ion batteries presents some unique benefits. One of them is to use cells made from established fabrication process and form factor, such as those offered by the 18650 cylindrical configuration, to provide a common platform to investigate and understand performance deficiency and aging mechanism of target chemistry. Such an approach shall afford us to derive relevant information without influence from processing or form factor variability that may skew our understanding on cell-level issues. A series of 1.9 Ah 18650 lithium ion cells developed by a commercial source using a composite positive electrode comprising (LiMn1/3Ni1/3Co1/3O2 + LiMn2O4) is being used as a platform for the investigation of certain key issues, particularly path-dependent aging and degradation in future plug-in hybrid electric vehicle (PHEV) applications, under the US Department of Energy's Applied Battery Research (ABR) program. Here we report in Part I the initial characterizations of the cell performance and Part II some aspects of cell degradation in 2C cycle aging. The initial characterizations, including cell-to-cell variability, are essential for life cycle performance characterization in the second part of the report when cell-aging phenomena are discussed. Due to the composite nature of the positive electrode, the features (or signature) derived from the incremental capacity (IC) of the cell appear rather complex. In this work, the method to index the observed IC peaks is discussed. Being able to index the IC signature in details is critical for analyzing and identifying degradation mechanism later in the cycle aging study.

  16. Evaluation of commercial lithium-ion cells based on composite positive electrode for plug-in hybrid electric vehicle applications. Part I: Initial characterizations

    NASA Astrophysics Data System (ADS)

    Dubarry, Matthieu; Truchot, Cyril; Cugnet, Mikaël; Liaw, Bor Yann; Gering, Kevin; Sazhin, Sergiy; Jamison, David; Michelbacher, Christopher

    Evaluating commercial Li-ion batteries presents some unique benefits. One of them is to use cells made from established fabrication process and form factor, such as those offered by the 18650 cylindrical configuration, to provide a common platform to investigate and understand performance deficiency and aging mechanism of target chemistry. Such an approach shall afford us to derive relevant information without influence from processing or form factor variability that may skew our understanding on cell-level issues. A series of 1.9 Ah 18650 lithium ion cells developed by a commercial source using a composite positive electrode comprising {LiMn 1/3Ni 1/3Co 1/3O 2 + LiMn 2O 4} is being used as a platform for the investigation of certain key issues, particularly path-dependent aging and degradation in future plug-in hybrid electric vehicle (PHEV) applications, under the US Department of Energy's Applied Battery Research (ABR) program. Here we report in Part I the initial characterizations of the cell performance and Part II some aspects of cell degradation in 2C cycle aging. The initial characterizations, including cell-to-cell variability, are essential for life cycle performance characterization in the second part of the report when cell-aging phenomena are discussed. Due to the composite nature of the positive electrode, the features (or signature) derived from the incremental capacity (IC) of the cell appear rather complex. In this work, the method to index the observed IC peaks is discussed. Being able to index the IC signature in details is critical for analyzing and identifying degradation mechanism later in the cycle aging study.

  17. On-line equalization for lithium-ion battery packs based on charging cell voltages: Part 2. Fuzzy logic equalization

    NASA Astrophysics Data System (ADS)

    Zheng, Yuejiu; Ouyang, Minggao; Lu, Languang; Li, Jianqiu; Han, Xuebing; Xu, Liangfei

    2014-02-01

    In the first part of this work, we propose dissipative cell equalization (DCE) algorithm based on remaining charging capacity estimation (RCCE) and establish a pack model with 8 cells in series. The results show that RCCE-DCE algorithm is suitable for on-line equalization in electric vehicles (EVs) and no over-equalization happens. However, 1% pack capacity difference from the DCE theoretical pack capacity is observed with RCCE-DCE algorithm. Therefore, as the second part of the series, we propose fuzzy logic (FL) DCE algorithm based on charging cell voltage curves (CCVCs). Cell capacities and SOCs are fuzzily identified in FL-DCE algorithm by comparing cell voltages at the beginning and end of charging. Adaptive FL-DCE is further improved to prevent over-equalization and maintain the equalization capability. The simulation results show that pack capacity difference from the DCE theoretical pack capacity with the adaptive FL-DCE is smaller than that with RCCE-DCE algorithm, and the duration of the infant stage is also shorter. The proposed adaptive FL-DCE is suitable for on-line equalization in EVs and well prevents over-equalization.

  18. NASA Aerospace Flight Battery Program: Generic Safety, Handling and Qualification Guidelines for Lithium-Ion (Li-Ion) Batteries; Availability of Source Materials for Lithium-Ion (Li-Ion) Batteries; Maintaining Technical Communications Related to Aerospace Batteries (NASA Aerospace Battery Workshop). Volume 1, Part 1

    NASA Technical Reports Server (NTRS)

    Manzo, Michelle A.; Brewer, Jeffrey C.; Bugga, Ratnakumar V.; Darcy, Eric C.; Jeevarajan, Judith A.; McKissock, Barbara I.; Schmitz, Paul C.

    2010-01-01

    This NASA Aerospace Flight Battery Systems Working Group was chartered within the NASA Engineering and Safety Center (NESC). The Battery Working Group was tasked to complete tasks and to propose proactive work to address battery related, agency-wide issues on an annual basis. In its first year of operation, this proactive program addressed various aspects of the validation and verification of aerospace battery systems for NASA missions. Studies were performed, issues were discussed and in many cases, test programs were executed to generate recommendations and guidelines to reduce risk associated with various aspects of implementing battery technology in the aerospace industry. This document contains Part 1 - Volume I: Generic Safety, Handling and Qualification Guidelines for Lithium-Ion (Li-Ion) Batteries, Availability of Source Materials for Lithium-Ion (Li-Ion) Batteries, and Maintaining Technical Communications Related to Aerospace Batteries (NASA Aerospace Battery Workshop).

  19. Degradation of lithium ion batteries employing graphite negatives and nickel-cobalt-manganese oxide + spinel manganese oxide positives: Part 1, aging mechanisms and life estimation

    NASA Astrophysics Data System (ADS)

    Wang, John; Purewal, Justin; Liu, Ping; Hicks-Garner, Jocelyn; Soukazian, Souren; Sherman, Elena; Sorenson, Adam; Vu, Luan; Tataria, Harshad; Verbrugge, Mark W.

    2014-12-01

    We examine the aging and degradation of graphite/composite metal oxide cells. Non-destructive electrochemical methods were used to monitor the capacity loss, voltage drop, resistance increase, lithium loss, and active material loss during the life testing. The cycle life results indicated that the capacity loss was strongly impacted by the rate, temperature, and depth of discharge (DOD). Lithium loss and active electrode material loss were studied by the differential voltage method; we find that lithium loss outpaces active material loss. A semi-empirical life model was established to account for both calendar-life loss and cycle-life loss. For the calendar-life equation, we adopt a square root of time relation to account for the diffusion limited capacity loss, and an Arrhenius correlation is used to capture the influence of temperature. For the cycle life, the dependence on rate is exponential while that for time (or charge throughput) is linear.

  20. Test results of lithium pool-air reaction suppression systems

    SciTech Connect

    Jeppson, D.W.

    1987-02-01

    Engineered reaction suppression systems were demonstrated to be effective in suppressing lithium pool-air reactions for lithium quantities up to 100 kg. Lithium pool-air reaction suppression system tests were conducted to evaluate suppression system effectiveness for potential use in fusion facilities in mitigating consequences of postulated lithium spills. Small-scale perforated and sacrificial cover plate suppression systems with delayed inert gas purging proved effective in controlling the lithium-air interaction for lithium quantities near 15 kg at initial temperatures up to 450/sup 0/C. A large-scale suppression system with a sacrificial cover, a diverter plate, an inert gas atmosphere, and remotely retrievable catch pans proved effective in controlling lithium pool-air interaction for a 100-kg lithium discharge at an initial temperature of 550/sup 0/C. This suppression system limited the maximum pool temperature to about 600/sup 0/C less than that expected for a similar lithium pool-air reaction without a suppression system. Lithium aerosol release from this large-scale suppression system was a factor of about 10,000 less than that expected for a lithium pool-air reaction with no suppression system. Remote retrieval techniques for lithium cleanup, such as (1) in-place lithium siphoning and overhead crane dismantling, and (2) lithium catch pan removal by use of an overhead crane, were demonstrated as part of this large-scale test.

  1. Lithium plating in a commercial lithium-ion battery - A low-temperature aging study

    NASA Astrophysics Data System (ADS)

    Petzl, Mathias; Kasper, Michael; Danzer, Michael A.

    2015-02-01

    The formation of metallic lithium on the negative graphite electrode in a lithium-ion (Li-ion) battery, also known as lithium plating, leads to severe performance degradation and may also affect the cell safety. This study is focused on the nondestructive characterization of the aging behavior during long-term cycling at plating conditions, i.e. low temperature and high charge rate. A commercial graphite/LiFePO4 Li-ion battery is investigated in order to elucidate the aging effects of lithium plating for real-world purposes. It is shown that lithium plating can be observed as a loss of cyclable lithium which affects the capacity balance of the electrodes. In this way, lithium plating counteracts its own occurrence during prolonged cycling. The capacity losses due to lithium plating are therefore decreasing at higher cycle numbers and the capacity retention curve exhibits an inflection point. It is further shown that the observed capacity fade is partly reversible. Electrochemical impedance spectroscopy (EIS) reveals a significant increase of the ohmic cell resistance due to electrolyte consumption during surface film formation on the plated lithium. Additional cell opening provides important quantitative information regarding the thickness of the lithium layer and the corresponding mass of the plated lithium.

  2. Simplification of physics-based electrochemical model for lithium ion battery on electric vehicle. Part I: Diffusion simplification and single particle model

    NASA Astrophysics Data System (ADS)

    Han, Xuebing; Ouyang, Minggao; Lu, Languang; Li, Jianqiu

    2015-03-01

    Now the lithium ion batteries are widely used in electrical vehicles (EV). The battery modeling and state estimation is of great significance. The rigorous physic based electrochemical model is too complicated for on-line simulation in vehicle. In this work, the simplification of physics-based model lithium ion battery for application in battery management system (BMS) on real electrical vehicle is proposed. Approximate method for solving the solid phase diffusion and electrolyte concentration distribution problems is introduced. The approximate result is very close to the rigorous model but fewer computations are needed. An extended single particle model is founded based on these approximated results and the on-line state of charge (SOC) estimation algorithm using the extended Kalman filter with this single particle model is discussed. This SOC estimation algorithm could be used in the BMS in real vehicle.

  3. Lithium in 2012

    USGS Publications Warehouse

    Jaskula, B.W.

    2013-01-01

    In 2012, estimated world lithium consumption was about 28 kt (31,000 st) of lithium contained in minerals and compounds, an 8 percent increase from that of 2011. Estimated U.S. consumption was about 2 kt (2,200 st) of contained lithium, the same as that of 2011. The United States was thought to rank fourth in consumption of lithium and remained the leading importer of lithium carbonate and the leading producer of value-added lithium materials. One company, Rockwood Lithium Inc., produced lithium compounds from domestic brine resources near Silver Peak, NV.

  4. Lithium-associated hyperthyroidism.

    PubMed

    Siyam, Fadi F; Deshmukh, Sanaa; Garcia-Touza, Mariana

    2013-08-01

    Goiters and hypothyroidism are well-known patient complications of the use of lithium for treatment of bipolar disease. However, the occurrence of lithium-induced hyperthyroidism is a more rare event. Many times, the condition can be confused with a flare of mania. Monitoring through serial biochemical measurement of thyroid function is critical in patients taking lithium. Hyperthyroidism induced by lithium is a condition that generally can be controlled medically without the patient having to discontinue lithium therapy, although in some circumstances, discontinuation of lithium therapy may be indicated. We report on a patient case of lithium-associated hyperthyroidism that resolved after discontinuation of the medication. PMID:23948626

  5. A preliminary deposit model for lithium brines

    USGS Publications Warehouse

    Bradley, Dwight; Munk, LeeAnn; Jochens, Hillary; Hynek, Scott; Labay, Keith A.

    2013-01-01

    This report is part of an effort by the U.S. Geological Survey to update existing mineral deposit models and to develop new ones. The global transition away from hydrocarbons toward energy alternatives increases demand for many scarce metals. Among these is lithium, a key component of lithium-ion batteries for electric and hybrid vehicles. Lithium brine deposits account for about three-fourths of the world’s lithium production. Updating an earlier deposit model, we emphasize geologic information that might directly or indirectly help in exploration for lithium brine deposits, or for assessing regions for mineral resource potential. Special attention is given to the best-known deposit in the world—Clayton Valley, Nevada, and to the giant Salar de Atacama, Chile.

  6. Lithium electric dipole polarizability

    SciTech Connect

    Puchalski, M.; KePdziera, D.; Pachucki, K.

    2011-11-15

    The electric dipole polarizability of the lithium atom in the ground state is calculated including relativistic and quantum electrodynamics corrections. The obtained result {alpha}{sub E}=164.0740(5) a.u. is in good agreement with the less accurate experimental value of 164.19(1.08) a.u. The small uncertainty of about 3 parts per 10{sup 6} comes from the approximate treatment of quantum electrodynamics corrections. Our theoretical result can be considered as a benchmark for more general atomic structure methods and may serve as a reference value for the relative measurement of polarizabilities of the other alkali-metal atoms.

  7. Development of a psoriasis-like syndrome following lithium therapy.

    PubMed

    Hanada, K; Tasaki, M; Hashimoto, I; Sone, M; Yamaguchi, T

    1987-12-01

    A correlation between lithium and psoriasis has been observed. In this paper, the case of a 17-yr-old girl is reported who developed psoriatic lesions after administration of lithium carbonate. Further-more, serum lithium levels in some psoriatic patients are disclosed, and induction of psoriasis by lithium in experimental animals is described. Serum lithium levels in 27 patients were significantly higher (p<0.025) than those of controls. Uninvolved parts of skin tissues obtained from three cases of psoriasis were transplanted to nude mice. After supplementing lithium as the chloride, these skin grafts developed the histologic change characteristic of psoriasis. However, the lithium compound by itself did not increase superoxide production of polymorphonuclear leukocytes in psoriasis. PMID:24254819

  8. Molten salt lithium cells

    DOEpatents

    Raistrick, Ian D.; Poris, Jaime; Huggins, Robert A.

    1983-01-01

    Lithium-based cells are promising for applications such as electric vehicles and load-leveling for power plants since lithium is very electropositive and light weight. One type of lithium-based cell utilizes a molten salt electrolyte and is operated in the temperature range of about 400.degree.-500.degree. C. Such high temperature operation accelerates corrosion problems and a substantial amount of energy is lost through heat transfer. The present invention provides an electrochemical cell (10) which may be operated at temperatures between about 100.degree.-170.degree. C. Cell (10) comprises an electrolyte (16), which preferably includes lithium nitrate, and a lithium or lithium alloy electrode (12).

  9. Molten salt lithium cells

    DOEpatents

    Raistrick, I.D.; Poris, J.; Huggins, R.A.

    1980-07-18

    Lithium-based cells are promising for applications such as electric vehicles and load-leveling for power plants since lithium is very electropositive and light weight. One type of lithium-based cell utilizes a molten salt electrolyte and is operated in the temperature range of about 400 to 500/sup 0/C. Such high temperature operation accelerates corrosion problems and a substantial amount of energy is lost through heat transfer. The present invention provides an electrochemical cell which may be operated at temperatures between about 100 to 170/sup 0/C. The cell is comprised of an electrolyte, which preferably includes lithium nitrate, and a lithium or lithium alloy electrode.

  10. Molten salt lithium cells

    DOEpatents

    Raistrick, Ian D.; Poris, Jaime; Huggins, Robert A.

    1982-02-09

    Lithium-based cells are promising for applications such as electric vehicles and load-leveling for power plants since lithium is very electropositive and light weight. One type of lithium-based cell utilizes a molten salt electrolyte and is operated in the temperature range of about 400.degree.-500.degree. C. Such high temperature operation accelerates corrosion problems and a substantial amount of energy is lost through heat transfer. The present invention provides an electrochemical cell (10) which may be operated at temperatures between about 100.degree.-170.degree. C. Cell (10) comprises an electrolyte (16), which preferably includes lithium nitrate, and a lithium or lithium alloy electrode (12).

  11. Preventing Overcharge And Overdischarge Of Lithium Cells

    NASA Technical Reports Server (NTRS)

    Huang, Chen-Kuo; Surampudi, Subbarao; Shen, David H.; Deligiannis, Fotios; Attia, Alan I.; Halpert, Gerald

    1995-01-01

    Secondary lithium cells operating at ambient temperature protected against overcharge and overdischarge by use of cathode additives acting as sources and sinks of electroactive chemical species, which is lithium. Additive in cathode limits excursion of voltage of cell during both overcharge and overdischarge. In addition to protecting cell, also serves as part of state-of-charge indicator: attainment of greater or lesser limiting voltage indicates end of charge or end of discharge, respectively. Concept applied to Li/TiS2 system, and also applicable to such other lithium systems as Li/MoS2, Li/NbSe3, and Li/V2O5.

  12. On-line equalization for lithium-ion battery packs based on charging cell voltages: Part 1. Equalization based on remaining charging capacity estimation

    NASA Astrophysics Data System (ADS)

    Zheng, Yuejiu; Ouyang, Minggao; Lu, Languang; Li, Jianqiu; Han, Xuebing; Xu, Liangfei

    2014-02-01

    Because of the inevitable inconsistency during manufacture and use of battery cells, cell variations in battery packs have significant impacts on battery pack capacities, durability and safety for electric vehicles (EVs). To reduce cell variations and increase pack capacity, cell equalization is essentially required. In the series of two papers, we discover that dissipative cell equalization (DCE) using dissipative resistances is a feasible on-line equalization method for battery packs in EVs. We subsequently propose on-line equalization algorithms for lithium-ion battery packs based on charging cell voltage curves (CCVCs). The objective of these algorithms is to maximize pack capacities by conditioning CCVCs. As the first paper of the series, we first briefly review equalization topologies and algorithms. We discover cell remaining charging capacity (RCC) can be on-line estimated and further propose DCE algorithm based on remaining charging capacity estimation (RCCE). We establish a pack model with 8 cells in series and simulate 4 scenes with different cell variations. RCCE-DCE algorithm is proved to be effective by comparing pack capacities with/without RCCE-DCE algorithm. The equalization capability and over-equalization prevention are further examined, and the result shows that RCCE-DCE algorithm is suitable for on-line equalization in EVs.

  13. Simplification of physics-based electrochemical model for lithium ion battery on electric vehicle. Part II: Pseudo-two-dimensional model simplification and state of charge estimation

    NASA Astrophysics Data System (ADS)

    Han, Xuebing; Ouyang, Minggao; Lu, Languang; Li, Jianqiu

    2015-03-01

    Now the lithium ion batteries are widely used in electric vehicles (EV). The battery modeling and state estimation are of great importance. The rigorous physics-based electrochemical model is too complicated for on-line simulation in vehicle. In this work, the simplification of the physics-based model for application on real vehicle is proposed. An improved single particle (SP) model is introduced with high precision and the same level of computations as the original single particle model. A simplified pseudo-two-dimensional (SP2D) model is developed. The distribution of the pore wall flux is analyzed and an approximate method is developed to find the solution. The developed models are compared with rigorous electrochemical model and original SP models. The results demonstrate that the models introduced in this work could simulate the battery efficiently without too much loss of accuracy. A state of charge (SOC) estimation algorithm using the Luenberger observer with the SP2D model is proposed and shows high precision. This SOC estimation method could be used in the BMS in real vehicle.

  14. Lithium use in batteries

    USGS Publications Warehouse

    Goonan, Thomas G.

    2012-01-01

    Lithium has a number of uses but one of the most valuable is as a component of high energy-density rechargeable lithium-ion batteries. Because of concerns over carbon dioxide footprint and increasing hydrocarbon fuel cost (reduced supply), lithium may become even more important in large batteries for powering all-electric and hybrid vehicles. It would take 1.4 to 3.0 kilograms of lithium equivalent (7.5 to 16.0 kilograms of lithium carbonate) to support a 40-mile trip in an electric vehicle before requiring recharge. This could create a large demand for lithium. Estimates of future lithium demand vary, based on numerous variables. Some of those variables include the potential for recycling, widespread public acceptance of electric vehicles, or the possibility of incentives for converting to lithium-ion-powered engines. Increased electric usage could cause electricity prices to increase. Because of reduced demand, hydrocarbon fuel prices would likely decrease, making hydrocarbon fuel more desirable. In 2009, 13 percent of worldwide lithium reserves, expressed in terms of contained lithium, were reported to be within hard rock mineral deposits, and 87 percent, within brine deposits. Most of the lithium recovered from brine came from Chile, with smaller amounts from China, Argentina, and the United States. Chile also has lithium mineral reserves, as does Australia. Another source of lithium is from recycled batteries. When lithium-ion batteries begin to power vehicles, it is expected that battery recycling rates will increase because vehicle battery recycling systems can be used to produce new lithium-ion batteries.

  15. The synergetic effect of lithium polysulfide and lithium nitrate to prevent lithium dendrite growth.

    PubMed

    Li, Weiyang; Yao, Hongbin; Yan, Kai; Zheng, Guangyuan; Liang, Zheng; Chiang, Yet-Ming; Cui, Yi

    2015-01-01

    Lithium metal has shown great promise as an anode material for high-energy storage systems, owing to its high theoretical specific capacity and low negative electrochemical potential. Unfortunately, uncontrolled dendritic and mossy lithium growth, as well as electrolyte decomposition inherent in lithium metal-based batteries, cause safety issues and low Coulombic efficiency. Here we demonstrate that the growth of lithium dendrites can be suppressed by exploiting the reaction between lithium and lithium polysulfide, which has long been considered as a critical flaw in lithium-sulfur batteries. We show that a stable and uniform solid electrolyte interphase layer is formed due to a synergetic effect of both lithium polysulfide and lithium nitrate as additives in ether-based electrolyte, preventing dendrite growth and minimizing electrolyte decomposition. Our findings allow for re-evaluation of the reactions regarding lithium polysulfide, lithium nitrate and lithium metal, and provide insights into solving the problems associated with lithium metal anodes. PMID:26081242

  16. The synergetic effect of lithium polysulfide and lithium nitrate to prevent lithium dendrite growth

    NASA Astrophysics Data System (ADS)

    Li, Weiyang; Yao, Hongbin; Yan, Kai; Zheng, Guangyuan; Liang, Zheng; Chiang, Yet-Ming; Cui, Yi

    2015-06-01

    Lithium metal has shown great promise as an anode material for high-energy storage systems, owing to its high theoretical specific capacity and low negative electrochemical potential. Unfortunately, uncontrolled dendritic and mossy lithium growth, as well as electrolyte decomposition inherent in lithium metal-based batteries, cause safety issues and low Coulombic efficiency. Here we demonstrate that the growth of lithium dendrites can be suppressed by exploiting the reaction between lithium and lithium polysulfide, which has long been considered as a critical flaw in lithium-sulfur batteries. We show that a stable and uniform solid electrolyte interphase layer is formed due to a synergetic effect of both lithium polysulfide and lithium nitrate as additives in ether-based electrolyte, preventing dendrite growth and minimizing electrolyte decomposition. Our findings allow for re-evaluation of the reactions regarding lithium polysulfide, lithium nitrate and lithium metal, and provide insights into solving the problems associated with lithium metal anodes.

  17. Method of recycling lithium borate to lithium borohydride through diborane

    DOEpatents

    Filby, Evan E.

    1976-01-01

    This invention provides a method for the recycling of lithium borate to lithium borohydride which can be reacted with water to generate hydrogen for utilization as a fuel. The lithium borate by-product of the hydrogen generation reaction is reacted with hydrogen chloride and water to produce boric acid and lithium chloride. The boric acid and lithium chloride are converted to lithium borohydride through a diborane intermediate to complete the recycle scheme.

  18. Lithium Redistribution in Lithium-Metal Batteries

    SciTech Connect

    Ferrese, A; Albertus, P; Christensen, J; Newman, J

    2012-01-01

    A model of a lithium-metal battery with a CoO2 positive electrode has been modeled in order to predict the movement of lithium in the negative electrode along the negative electrode/separator interface during cell cycling. A finite-element approach was used to incorporate an intercalation positive electrode using superposition, electrode tabbing, transport using concentrated solution theory, as well as the net movement of the lithium electrode during cycling. From this model, it has been found that movement of lithium along the negative electrode/separator interface does occur during cycling and is affected by three factors: the cell geometry, the slope of the open-circuit-potential function of the positive electrode, and concentration gradients in both the solid and liquid phases in the cell. (C) 2012 The Electrochemical Society. [DOI: 10.1149/2.027210jes] All rights reserved.

  19. Lithium and symptomatic hyperparathyroidism.

    PubMed Central

    Ananth, J; Dubin, S E

    1983-01-01

    Hyperparathyroidism with or without adenoma has occasionally been reported in association with lithium treatment, and in symptomatic patients depression, psychosis and an exacerbation of existing psychopathology may occur. Three lithium-treated patients with hyperparathyroidism are reported, in whom discontinuation of lithium in one and removal of parathyroid adenomata in two led to both a reduction in plasma calcium levels and an improvement in their psychopathology. PMID:6423822

  20. Lithium purification technique

    DOEpatents

    Keough, R.F.; Meadows, G.E.

    1984-01-10

    A method for purifying liquid lithium to remove unwanted quantities of nitrogen or aluminum. The method involves precipitation of aluminum nitride by adding a reagent to the liquid lithium. The reagent will be either nitrogen or aluminum in a quantity adequate to react with the unwanted quantity of the impurity to form insoluble aluminum nitride. The aluminum nitride can be mechanically separated from the molten liquid lithium.

  1. Lithium purification technique

    DOEpatents

    Keough, Robert F.; Meadows, George E.

    1985-01-01

    A method for purifying liquid lithium to remove unwanted quantities of nitrogen or aluminum. The method involves precipitation of aluminum nitride by adding a reagent to the liquid lithium. The reagent will be either nitrogen or aluminum in a quantity adequate to react with the unwanted quantity of the impurity to form insoluble aluminum nitride. The aluminum nitride can be mechanically separated from the molten liquid lithium.

  2. Laminar Multicell Lithium Batteries

    SciTech Connect

    Bruder, A. H.

    1984-01-31

    Laminar batteries of series connected cells comprising lithium anodes and an electrolyte containing a passivating solvent reactive with lithium in which the cells are electrically connected in series by intercell barriers comprising outer layers of electrochemically inert electronically conducting material in contact with the electrochemically active anode and cathode of adjacent cells and a layer of metal foil between the electrochemically inert layers.

  3. Cathode material for lithium batteries

    DOEpatents

    Park, Sang-Ho; Amine, Khalil

    2015-01-13

    A method of manufacture an article of a cathode (positive electrode) material for lithium batteries. The cathode material is a lithium molybdenum composite transition metal oxide material and is prepared by mixing in a solid state an intermediate molybdenum composite transition metal oxide and a lithium source. The mixture is thermally treated to obtain the lithium molybdenum composite transition metal oxide cathode material.

  4. Cathode material for lithium batteries

    DOEpatents

    Park, Sang-Ho; Amine, Khalil

    2013-07-23

    A method of manufacture an article of a cathode (positive electrode) material for lithium batteries. The cathode material is a lithium molybdenum composite transition metal oxide material and is prepared by mixing in a solid state an intermediate molybdenum composite transition metal oxide and a lithium source. The mixture is thermally treated to obtain the lithium molybdenum composite transition metal oxide cathode material.

  5. Lithium and autophagy.

    PubMed

    Motoi, Yumiko; Shimada, Kohei; Ishiguro, Koichi; Hattori, Nobutaka

    2014-06-18

    Lithium, a drug used to treat bipolar disorders, has a variety of neuroprotective mechanisms, including autophagy regulation, in various neuropsychiatric conditions. In neurodegenerative diseases, lithium enhances degradation of aggregate-prone proteins, including mutated huntingtin, phosphorylated tau, and α-synuclein, and causes damaged mitochondria to degrade, while in a mouse model of cerebral ischemia and Alzheimer's disease autophagy downregulation by lithium is observed. The signaling pathway of lithium as an autophagy enhancer might be associated with the mammalian target of rapamycin (mTOR)-independent pathway, which is involved in myo-inositol-1,4,5-trisphosphate (IP3) in Huntington's disease and Parkinson's disease. However, the mTOR-dependent pathway might be involved in inhibiting glycogen synthase kinase-3β (GSK3β) in other diseases. Lithium's autophagy-enhancing property may contribute to the therapeutic benefit of patients with neuropsychiatric disorders. PMID:24738557

  6. Lithium metal oxide electrodes for lithium batteries

    DOEpatents

    Thackeray, Michael M.; Kim, Jeom-Soo; Johnson, Christopher S.

    2008-01-01

    An uncycled electrode for a non-aqueous lithium electrochemical cell including a lithium metal oxide having the formula Li.sub.(2+2x)/(2+x)M'.sub.2x/(2+x)M.sub.(2-2x)/(2+x)O.sub.2-.delta., in which 0.ltoreq.x<1 and .delta. is less than 0.2, and in which M is a non-lithium metal ion with an average trivalent oxidation state selected from two or more of the first row transition metals or lighter metal elements in the periodic table, and M' is one or more ions with an average tetravalent oxidation state selected from the first and second row transition metal elements and Sn. Methods of preconditioning the electrodes are disclosed as are electrochemical cells and batteries containing the electrodes.

  7. A comparative study of pi-arene-bridged lanthanum arylamide and aryloxide dimers. Solution behavior, exchange mechanisms, and X-ray crystal structures of La2(NH-2,6-iPr2C6H3)6, La(NH-2,6-iPr2C6H3)3(THF)3, and La(NH-2,6-iPr2C6H3)3(py)2.

    PubMed

    Giesbrecht, Garth R; Gordon, John C; Clark, David L; Hay, P Jeffrey; Scott, Brian L; Tait, C Drew

    2004-05-26

    Reaction of 3 equiv of 2,6-diisopropylaniline with La[N(SiMe(3))(2)](3) produces the dimeric species La(2)(NHAr)(6) (1). X-ray crystallography reveals a centrosymmetric structure, where the dimeric unit is bridged by intermolecular eta(6)-arene interactions of a unique arylamide ligand attached to an adjacent metal center. Exposure of 1 to THF results in formation of the monomeric tris-THF adduct La(NHAr)(3)(THF)(3) (2), which was shown by X-ray crystallography to maintain a fac-octahedral structure in the solid state. (1)H NMR spectroscopy illustrates that the binding of THF to 1 to form 2 is reversible and removal of THF under vacuum regenerates dimeric 1. Addition of pyridine to 1 yields the monomeric bis-pyridine adduct La(NHAr)(3)(py)(2) (3), which exhibits a distorted trigonal-bipyramidal La metal center. Solution (1)H NMR, IR, and Raman spectroscopy indicate that the pi-arene-bridged dimeric structure of 1 is maintained in solution. Variable-temperature (1)H NMR spectroscopic investigations of 1 are consistent with a monomer-dimer equilibrium at elevated temperature. In contrast, variable-temperature (1)H NMR spectroscopic investigations of the aryloxide analogue La(2)(OAr)(6) (4) show that the bridging and terminal aryloxide groups exchange by a mechanism in which the dimeric nature of the compound is retained. Density functional theory (DFT) calculations were carried out on model compounds La(2)(OC(6)H(5))(6), La(2)(NHC(6)H(5))(6), and (C(6)H(5)R)La(XC(6)H(5))(3), where X = O or NH and R = H, OH, or NH(2). The formation of eta(6)-arene interactions is energetically favored over monomeric LaX(3) (X = OPh or NHPh) with the aryloxide pi-arene interaction being stronger than the arylamide pi-arene interaction. Calculation of vibrational frequencies reveals the origin of the observed IR spectral behavior of both La(2)(OC(6)H(5))(6) and La(2)(NHC(6)H(5))(6), with the higher energy nu(C=C) stretch due to terminal ligands and the lower energy stretch associated

  8. Lithium chloride and avoidance of novel places.

    PubMed

    Kurz, E M; Levitsky, D A

    1983-06-01

    Rats were exposed to a distinctive chamber (chamber A, part of a two-chamber apparatus), which was novel for half of the rats but familiar for the other half. Each rat was subsequently injected with lithium chloride or saline. In a test trial conducted 24 hr later, all rats were given a choice between chamber A and a second chamber (B), which was novel for all rats. The main result was that the group made familiar with chamber A and then given lithium showed a significant preference for that side or an avoidance of the novel side, a "spatial neophobia." A second experiment confirmed the spatial neophobia effect and demonstrated that it was not dependent on the particular conditioning procedure used in the first experiment. The spatial neophobia effect was related to similar effects in the taste aversion literature, and to the results of research on lithium-induced decreases in exploratory behavior. PMID:6307325

  9. Lithium mass transport in ceramic breeder materials

    SciTech Connect

    Blackburn, P.E.; Johnson, C.E.

    1990-01-01

    The objective of this activity is to measure the lithium vaporization from lithium oxide breeder material under differing temperature and moisture partial pressure conditions. Lithium ceramics are being investigated for use as tritium breeding materials. The lithium is readily converted to tritium after reacting with a neutron. With the addition of 1000 ppM H{sub 2} to the He purge gas, the bred tritium is readily recovered from the blanket as HT and HTO above 400{degree}C. Within the solid, tritium may also be found as LiOT which may transport lithium to cooler parts of the blanket. The pressure of LiOT(g), HTO(g), or T{sub 2}O(g) above Li{sub 2}O(s) is the same as that for reactions involving hydrogen. In our experiments we were limited to the use of hydrogen. The purpose of this work is to investigate the transport of LiOH(g) from the blanket material. 8 refs., 1 fig., 3 tabs.

  10. Lithium cell test results

    NASA Technical Reports Server (NTRS)

    Bragg, B. J.

    1977-01-01

    Three lithium SO2 cells, two lithium CF cells, and a vinyl chloride cell, all with crimped seals, and all strictly experimental, were independently discharged on resistors. Three temperatures were used and several different storage temperatures. Discharge rate generally on the nominal discharges were 0.1 amp, 0.5 amp, and 1 amp. Tests results show that the crimp seals are inadequate, especially for the SO2 cells. Normal discharges present no hazards. All cells discharge to zero. The problem of lithium cell explosions, such as occurred during off-limits testing, is discussed.

  11. Lithium Dendrite Formation

    SciTech Connect

    2015-03-06

    Scientists at the Department of Energy’s Oak Ridge National Laboratory have captured the first real-time nanoscale images of lithium dendrite structures known to degrade lithium-ion batteries. The ORNL team’s electron microscopy could help researchers address long-standing issues related to battery performance and safety. Video shows annular dark-field scanning transmission electron microscopy imaging (ADF STEM) of lithium dendrite nucleation and growth from a glassy carbon working electrode and within a 1.2M LiPF6 EC:DM battery electrolyte.

  12. Manufacturing of Protected Lithium Electrodes for Advanced Lithium-Air, Lithium-Water & Lithium-Sulfur Batteries

    SciTech Connect

    Visco, Steven J

    2015-11-30

    The global demand for rechargeable batteries is large and growing rapidly. Assuming the adoption of electric vehicles continues to increase, the need for smaller, lighter, and less expensive batteries will become even more pressing. In this vein, PolyPlus Battery Company has developed ultra-light high performance batteries based on its proprietary protected lithium electrode (PLE) technology. The Company’s Lithium-Air and Lithium-Seawater batteries have already demonstrated world record performance (verified by third party testing), and we are developing advanced lithium-sulfur batteries which have the potential deliver high performance at low cost. In this program PolyPlus Battery Company teamed with Corning Incorporated to transition the PLE technology from bench top fabrication using manual tooling to a pre- commercial semi-automated pilot line. At the inception of this program PolyPlus worked with a Tier 1 battery manufacturing engineering firm to design and build the first-of-its-kind pilot line for PLE production. The pilot line was shipped and installed in Berkeley, California several months after the start of the program. PolyPlus spent the next two years working with and optimizing the pilot line and now produces all of its PLEs on this line. The optimization process successfully increased the yield, throughput, and quality of PLEs produced on the pilot line. The Corning team focused on fabrication and scale-up of the ceramic membranes that are key to the PLE technology. PolyPlus next demonstrated that it could take Corning membranes through the pilot line process to produce state-of-the-art protected lithium electrodes. In the latter part of the program the Corning team developed alternative membranes targeted for the large rechargeable battery market. PolyPlus is now in discussions with several potential customers for its advanced PLE-enabled batteries, and is building relationships and infrastructure for the transition into manufacturing. It is likely

  13. Lithium metal oxide electrodes for lithium batteries

    DOEpatents

    Thackeray, Michael M.; Johnson, Christopher S.; Amine, Khalil; Kang, Sun-Ho

    2010-06-08

    An uncycled preconditioned electrode for a non-aqueous lithium electrochemical cell including a lithium metal oxide having the formula xLi.sub.2-yH.sub.yO.xM'O.sub.2.(1-x)Li.sub.1-zH.sub.zMO.sub.2 in which 0lithium metal ion with an average trivalent oxidation state selected from two or more of the first row transition metals or lighter metal elements in the periodic table, and M' is one or more ions with an average tetravalent oxidation state selected from the first and second row transition metal elements and Sn. The xLi.sub.2-yH.sub.y.xM'O.sub.2.(1-x)Li.sub.1-zH.sub.zMO.sub.2 material is prepared by preconditioning a precursor lithium metal oxide (i.e., xLi.sub.2M'O.sub.3.(1-x)LiMO.sub.2) with a proton-containing medium with a pH<7.0 containing an inorganic acid. Methods of preparing the electrodes are disclosed, as are electrochemical cells and batteries containing the electrodes.

  14. Lithium plating in lithium-ion batteries at sub-ambient temperatures investigated by in situ neutron diffraction

    NASA Astrophysics Data System (ADS)

    Zinth, Veronika; von Lüders, Christian; Hofmann, Michael; Hattendorff, Johannes; Buchberger, Irmgard; Erhard, Simon; Rebelo-Kornmeier, Joana; Jossen, Andreas; Gilles, Ralph

    2014-12-01

    Lithium plating in commercial LiNi1/3Mn1/3Co1/3O2/graphite cells at sub-ambient temperatures is studied by neutron diffraction at Stress-Spec, MLZ. Li plating uses part of the active lithium in the cell and competes with the intercalation of lithium into graphite. As a result, the degree of graphite lithiation during and after charge is lower. Comparison of graphite lithiation after a C/5 charging cycle fast enough to expect a considerable amount of Li plating with a much slower C/30 reference cycle reveals a lower degree of graphite lithiation in the first case; neutron diffraction shows less LiC6 and more LiC12 is present. If the cell is subjected to a 20 h rest period after charge, a gradual transformation of remaining LiC12 to LiC6 can be observed, indicating Li diffusion into the graphite. During the rest period after the C/5 charging cycle, the degree of graphite lithiation can be estimated to increase by 17%, indicating at least 17% of the active lithium is plated. Data collected during discharge immediately after C/5 charging give further evidence of the presence and amount of metallic lithium: in this case 19% of discharge capacity originates from the oxidation of metallic lithium. Also, lithium oxidation can be directly related to the high voltage plateau observed during discharge in case of lithium plating.

  15. Lithium drifted germanium system

    NASA Technical Reports Server (NTRS)

    Fjarlie, E. J.

    1969-01-01

    General characteristics of the lithium-drifted germanium photodiode-Dewar-preamplifier system and particular operating instructions for the device are given. Information is included on solving operational problems.

  16. APPARATUS FOR THE PRODUCTION OF LITHIUM METAL

    DOEpatents

    Baker, P.S.; Duncan, F.R.; Greene, H.B.

    1961-08-22

    Methods and apparatus for the production of high-purity lithium from lithium halides are described. The apparatus is provided for continuously contacting a molten lithium halide with molten barium, thereby forming lithium metal and a barium halide, establishing separate layers of these reaction products and unreacted barium and lithium halide, and continuously withdrawing lithium and barium halide from the reaction zone. (AEC)

  17. Scoping studies: behavior and control of lithium and lithium aerosols

    SciTech Connect

    Jeppson, D W

    1982-01-01

    The HEDL scoping studies examining the behavior of lithium and lithium aerosols have been conducted to determine and examine potential safety and environmental issues for postulated accident conditions associated with the use of lithium as a fusion reactor blanket and/or coolant. Liquid lithium reactions with air, nitrogen, carbon dioxide and concretes have been characterized. The effectiveness of various powder extinguishing agents and methods of application were determined for lithium-air reactions. The effectiveness of various lithium aerosol collection methods were determined and the volatilization and transport of radioactive metals potentially associated with lithium-air reactions were evaluated. Liquid lithium atmosphere reactions can be safely controlled under postulated accident conditions, but special handling practices must be provided. Lithium-concrete reactions should be avoided because of the potential production of high temperatures, corrosive environment and hydrogen. Carbon microspheres are effective in extinguishing well established lithium-air reactions for the lithium quantities tested (up to 10 kg). Large mass loading of lithium aerosols can be efficiently collected with conventional air cleaning systems. Potentially radioactive species (cobalt, iron and manganese) will be volatilized in a lithium-air reaction in contact with neutron activated stainless steel.

  18. Lithium to the Rescue.

    PubMed

    Jope, Richard S; Nemeroff, Charles B

    2016-01-01

    Lithium, an element that Mother Nature has put in some drinking water sources, has been used for its curative powers for centuries. Today, it's given in capsule form as a mood stabilizer for bipolar disorder and depression. New research, however, reveals its role as a neuroprotector, and suggests that a better understanding of the role enzymes modulated by lithium play could lead to new treatments for Alzheimer's disease, Parkinson's disease, multiple sclerosis, and other neurodegenerative disorders. PMID:27408673

  19. Lithium battery management system

    DOEpatents

    Dougherty, Thomas J.

    2012-05-08

    Provided is a system for managing a lithium battery system having a plurality of cells. The battery system comprises a variable-resistance element electrically connected to a cell and located proximate a portion of the cell; and a device for determining, utilizing the variable-resistance element, whether the temperature of the cell has exceeded a predetermined threshold. A method of managing the temperature of a lithium battery system is also included.

  20. Solid-state lithium battery

    SciTech Connect

    Ihlefeld, Jon; Clem, Paul G; Edney, Cynthia; Ingersoll, David; Nagasubramanian, Ganesan; Fenton, Kyle Ross

    2014-11-04

    The present invention is directed to a higher power, thin film lithium-ion electrolyte on a metallic substrate, enabling mass-produced solid-state lithium batteries. High-temperature thermodynamic equilibrium processing enables co-firing of oxides and base metals, providing a means to integrate the crystalline, lithium-stable, fast lithium-ion conductor lanthanum lithium tantalate (La.sub.1/3-xLi.sub.3xTaO.sub.3) directly with a thin metal foil current collector appropriate for a lithium-free solid-state battery.

  1. Toxic effect of lithium in mouse brain

    SciTech Connect

    Dixit, P.K.; Smithberg, M.

    1988-01-01

    The effect of lithium ion on glucose oxidation in the cerebrum and cerebellum of mice was measured in vitro by the conversion of isotopic glucose into /sup 14/CO/sub 2//mg wet weight. Glucose utilization is unaffected by lowest lithium dosage but is inhibited by high lithium concentrations (197-295 mM). Chronic administration of lithium to adult mice decreased the DNA content of the cerebrum and cerebellum at concentrations of 80 and 108 mM. The DNA content of selected postnatal stages of cerebrum and cerebellum was measured starting on Day 1 or 2. This served as another parameter to evaluate glucose oxidation studies at these ages. On the basis of wet weight, both brain parts of neonates of ages 1 and 10 days were approximately one-half that of the adult counterparts. On the basis of DNA content, the cerebrum enhanced its glucose utilization twofold from Day 1 to Day 10 and tripled its utilization from Day 10 to Day 20. The glucose utilization by cerebrum at Day 20 is similar to adult values. In contrast, glucose oxidation in the cerebellum remained relatively constant throughout the postnatal growth. The relative susceptibility of the two brain parts is discussed.

  2. Hydrogen Outgassing from Lithium Hydride

    SciTech Connect

    Dinh, L N; Schildbach, M A; Smith, R A; Balazs1, B; McLean II, W

    2006-04-20

    Lithium hydride is a nuclear material with a great affinity for moisture. As a result of exposure to water vapor during machining, transportation, storage and assembly, a corrosion layer (oxide and/or hydroxide) always forms on the surface of lithium hydride resulting in the release of hydrogen gas. Thermodynamically, lithium hydride, lithium oxide and lithium hydroxide are all stable. However, lithium hydroxides formed near the lithium hydride substrate (interface hydroxide) and near the sample/vacuum interface (surface hydroxide) are much less thermally stable than their bulk counterpart. In a dry environment, the interface/surface hydroxides slowly degenerate over many years/decades at room temperature into lithium oxide, releasing water vapor and ultimately hydrogen gas through reaction of the water vapor with the lithium hydride substrate. This outgassing can potentially cause metal hydriding and/or compatibility issues elsewhere in the device. In this chapter, the morphology and the chemistry of the corrosion layer grown on lithium hydride (and in some cases, its isotopic cousin, lithium deuteride) as a result of exposure to moisture are investigated. The hydrogen outgassing processes associated with the formation and subsequent degeneration of this corrosion layer are described. Experimental techniques to measure the hydrogen outgassing kinetics from lithium hydride and methods employing the measured kinetics to predict hydrogen outgassing as a function of time and temperature are presented. Finally, practical procedures to mitigate the problem of hydrogen outgassing from lithium hydride are discussed.

  3. Lithium: for harnessing renewable energy

    USGS Publications Warehouse

    Bradley, Dwight; Jaskula, Brian

    2014-01-01

    Lithium, which has the chemical symbol Li and an atomic number of 3, is the first metal in the periodic table. Lithium has many uses, the most prominent being in batteries for cell phones, laptops, and electric and hybrid vehicles. Worldwide sources of lithium are broken down by ore-deposit type as follows: closed-basin brines, 58%; pegmatites and related granites, 26%; lithium-enriched clays, 7%; oilfield brines, 3%; geothermal brines, 3%; and lithium-enriched zeolites, 3% (2013 statistics). There are over 39 million tons of lithium resources worldwide. Of this resource, the USGS estimates there to be approximately 13 million tons of current economically recoverable lithium reserves. To help predict where future lithium supplies might be located, USGS scientists study how and where identified resources are concentrated in the Earth’s crust, and they use that knowledge to assess the likelihood that undiscovered resources also exist.

  4. Rechargeable ambient temperature lithium cells

    NASA Technical Reports Server (NTRS)

    Holleck, G. L.

    1980-01-01

    The cycling performance of a secondary lithium cell with a 2-methyl THF lithium hectofluorarsenate electrolyte is discussed. Stripping efficiency, dendritization, passivation on standing, and discharge efficiency are considered.

  5. Materials issues in lithium ion rechargeable battery technology

    SciTech Connect

    Doughty, D.H.

    1995-07-01

    Lithium ion rechargeable batteries are predicted to replace Ni/Cd as the workhorse consumer battery. The pace of development of this battery system is determined in large part by the availability of materials and the understanding of interfacial reactions between materials. Lithium ion technology is based on the use of two lithium intercalating electrodes. Carbon is the most commonly used anode material, while the cathode materials of choice have been layered lithium metal chalcogenides (LiMX{sub 2}) and lithium spinel-type compounds. Electrolytes may be either organic liquids or polymers. Although the first practical use of graphite intercalation compounds as battery anodes was reported in 1981 for molten salt cells and in 1983 for ambient temperature systems, it was not until Sony Energytech announced a new lithium ion intercalating carbon anode in 1990, that interest peaked. The reason for this heightened interest is that these electrochemical cells have the high energy density, high voltage and light weight of metallic lithium, but without the disadvantages of dendrite formation on charge, improving their safety and cycle life.

  6. Reversibility of anodic lithium in rechargeable lithium-oxygen batteries.

    PubMed

    Shui, Jiang-Lan; Okasinski, John S; Kenesei, Peter; Dobbs, Howard A; Zhao, Dan; Almer, Jonathan D; Liu, Di-Jia

    2013-01-01

    Non-aqueous lithium-air batteries represent the next-generation energy storage devices with very high theoretical capacity. The benefit of lithium-air batteries is based on the assumption that the anodic lithium is completely reversible during the discharge-charge process. Here we report our investigation on the reversibility of the anodic lithium inside of an operating lithium-air battery using spatially and temporally resolved synchrotron X-ray diffraction and three-dimensional micro-tomography technique. A combined electrochemical process is found, consisting of a partial recovery of lithium metal during the charging cycle and a constant accumulation of lithium hydroxide under both charging and discharging conditions. A lithium hydroxide layer forms on the anode separating the lithium metal from the separator. However, numerous microscopic 'tunnels' are also found within the hydroxide layer that provide a pathway to connect the metallic lithium with the electrolyte, enabling sustained ion-transport and battery operation until the total consumption of lithium. PMID:23929396

  7. Surface analysis of lithium coatings in NSTX

    NASA Astrophysics Data System (ADS)

    Timberlake, J.; Kugel, H. W.; Skinner, C. H.; Yao, N.

    2007-11-01

    Lithium coatings have been applied to NSTX plasma facing surfaces as part of a long term program to explore the potential for lithium to improve plasma and PFC performance. A LIThium EvaporatoR (LITER) directed a collimated stream of lithium vapor from an upper vacuum vessel port toward the graphite tiles of the lower center stack and divertor either before, or continuously between and during, discharges. Silicon witness coupons and other samples were retrieved from the vacuum vessel after the campaign and the surface morphology and elemental compostion examined with a XL30 FEG-SEM microscope equipped with an energy dispersed X-rays system sensitive to elements with atomic number greater than 4. The surfaces showed a complex morphology with nucleation sites apparent. Carbon and oxygen were the dominant impurities. Trace metals (Fe and Cr) were detected in the coating on the Si coupon, but not in a flake of bulk Li. We will present results of the surface analysis of samples exposed to Li evaporation in NSTX.

  8. A review of lithium deposition in lithium-ion and lithium metal secondary batteries

    NASA Astrophysics Data System (ADS)

    Li, Zhe; Huang, Jun; Yann Liaw, Bor; Metzler, Viktor; Zhang, Jianbo

    2014-05-01

    Major aspects related to lithium deposition in lithium-ion and lithium metal secondary batteries are reviewed. For lithium-ion batteries with carbonaceous anode, lithium deposition may occur under harsh charging conditions such as overcharging or charging at low temperatures. The major technical solutions include: (1) applying electrochemical models to predict the critical conditions for deposition initiation; (2) preventions by improved battery design and material modification; (3) applying adequate charging protocols to inhibit lithium deposition. For lithium metal secondary batteries, the lithium deposition is the inherent reaction during charging. The major technical solutions include: (1) the use of mechanistic models to elucidate and control dendrite initiation and growth; (2) engineering surface morphology of the lithium deposition to avoid dendrite formation via adjusting the composition and concentration of the electrolyte; (3) controlling battery working conditions. From a survey of the literature, the areas that require further study are proposed; e.g., refining the lithium deposition criteria, developing an effective AC self pre-heating method for low-temperature charging of lithium-ion batteries, and clarifying the role the solid electrolyte interphase (SEI) plays in determining the deposition morphology; to facilitate a refined control of the lithium deposition.

  9. Testing of Liquid Lithium Limiters in CDX-U

    SciTech Connect

    R. Majeski; R. Kaita; M. Boaz; P. Efthimion; T. Gray; B. Jones; D. Hoffman; H. Kugel; J. Menard; T. Munsat; A. Post-Zwicker; V. Soukhanovskii; J. Spaleta; G. Taylor; J. Timberlake; R. Woolley; L. Zakharov; M. Finkenthal; D. Stutman; G. Antar; R. Doerner; S. Luckhardt; R. Seraydarian; R. Maingi; M. Maiorano; S. Smith; D. Rodgers

    2004-07-30

    Part of the development of liquid metals as a first wall or divertor for reactor applications must involve the investigation of plasma-liquid metal interactions in a functioning tokamak. Most of the interest in liquid-metal walls has focused on lithium. Experiments with lithium limiters have now been conducted in the Current Drive Experiment-Upgrade (CDX-U) device at the Princeton Plasma Physics Laboratory. Initial experiments used a liquid-lithium rail limiter (L3) built by the University of California at San Diego. Spectroscopic measurements showed some reduction of impurities in CDX-U plasmas with the L3, compared to discharges with a boron carbide limiter. While no reduction in recycling was observed with the L3, which had a plasma-wet area of approximately 40 cm2, subsequent experiments with a larger area fully toroidal lithium limiter demonstrated significant reductions in both recycling and in impurity levels. Two series of experiments with the toroidal limiter have now be en performed. In each series, the area of exposed, clean lithium was increased, until in the latest experiments the liquid-lithium plasma-facing area was increased to 2000 cm2. Under these conditions, the reduction in recycling required a factor of eight increase in gas fueling in order to maintain the plasma density. The loop voltage required to sustain the plasma current was reduced from 2 V to 0.5 V. This paper summarizes the technical preparations for lithium experiments and the conditioning required to prepare the lithium surface for plasma operations. The mechanical response of the liquid metal to induced currents, especially through contact with the plasma, is discussed. The effect of the lithium-filled toroidal limiter on plasma performance is also briefly described.

  10. Lithium Dinitramide as an Additive in Lithium Power Cells

    NASA Technical Reports Server (NTRS)

    Gorkovenko, Alexander A.

    2007-01-01

    Lithium dinitramide, LiN(NO2)2 has shown promise as an additive to nonaqueous electrolytes in rechargeable and non-rechargeable lithium-ion-based electrochemical power cells. Such non-aqueous electrolytes consist of lithium salts dissolved in mixtures of organic ethers, esters, carbonates, or acetals. The benefits of adding lithium dinitramide (which is also a lithium salt) include lower irreversible loss of capacity on the first charge/discharge cycle, higher cycle life, lower self-discharge, greater flexibility in selection of electrolyte solvents, and greater charge capacity. The need for a suitable electrolyte additive arises as follows: The metallic lithium in the anode of a lithium-ion-based power cell is so highly reactive that in addition to the desired main electrochemical reaction, it engages in side reactions that cause formation of resistive films and dendrites, which degrade performance as quantified in terms of charge capacity, cycle life, shelf life, first-cycle irreversible capacity loss, specific power, and specific energy. The incidence of side reactions can be reduced through the formation of a solid-electrolyte interface (SEI) a thin film that prevents direct contact between the lithium anode material and the electrolyte. Ideally, an SEI should chemically protect the anode and the electrolyte from each other while exhibiting high conductivity for lithium ions and little or no conductivity for electrons. A suitable additive can act as an SEI promoter. Heretofore, most SEI promotion was thought to derive from organic molecules in electrolyte solutions. In contrast, lithium dinitramide is inorganic. Dinitramide compounds are known as oxidizers in rocket-fuel chemistry and until now, were not known as SEI promoters in battery chemistry. Although the exact reason for the improvement afforded by the addition of lithium dinitramide is not clear, it has been hypothesized that lithium dinitramide competes with other electrolyte constituents to react with

  11. Structural factors affecting lithium transport in lithium-excess layered cathode materials

    NASA Astrophysics Data System (ADS)

    Fell, Christopher R.

    Lithium ion batteries have drawn significant attention as the principle energy storage device powering today's mobile electronic equipment. Despite the increased usage, the performance of current lithium ion battery technology falls short of the requirements needed for large format applications such as electric vehicles. The layered lithium-excess oxide compounds Li[NixLi1/3-2x/3Mn2/3-x/3]O2 are of interest as a new generation of cathode materials for high energy density lithium ion batteries. Efforts to achieve a better understanding of the electrochemistry of lithium-excess materials require the connection of crystal structure to electrochemical properties. In this dissertation, a combination of advanced characterization techniques was used as a tool to understand the intercalation mechanism of the layered lithium-excess transition metal oxide Li[NixLi1/3-2x/3Mn 2/3-x/3]O2. The research identified that synthesis influences the structure of the material specifically the surface of the particles. The formation of a hydroxide rich surface film decreases the electrochemical performance. Post synthesis modifications including high pressure and high temperature leads to the formation of a second layered phase in the bulk; however, the treated samples display good electrochemical properties. This result underlines the flexibility of the structure of Li[NixLi1/3-2x/3Mn 2/3-x/3]O2, a feature uncommon to other layered transition metal oxides. Surface characterization of the layered lithium-excess cathodes following electrochemical cycling revealed the formation of a new surface phase 1 to 5 nm thick as well as insight to the complex cation rearrangement process and phase transformation. This part of the research identified that significant changes occurred during electrochemical cycling; however did not identify when the transformations occurred. Investigation using in situ techniques during the first electrochemical cycle shows that the structure undergoes irreversible

  12. Lithium Ion Batteries

    NASA Technical Reports Server (NTRS)

    1997-01-01

    Lithium ion batteries, which use a new battery chemistry, are being developed under cooperative agreements between Lockheed Martin, Ultralife Battery, and the NASA Lewis Research Center. The unit cells are made in flat (prismatic) shapes that can be connected in series and parallel to achieve desired voltages and capacities. These batteries will soon be marketed to commercial original-equipment manufacturers and thereafter will be available for military and space use. Current NiCd batteries offer about 35 W-hr/kg compared with 110 W-hr/kg for current lithium ion batteries. Our ultimate target for these batteries is 200 W-hr/kg.

  13. LITHIUM PROPHYLAXIS IN AFFECTIVE DISORDER

    PubMed Central

    Rao, A. Venkoba; Hariharasubramanian, N.; Devi, S. Parvathi; Sugumar, A.; Srinivasan, V.

    1982-01-01

    SUMMARY Out of 108 patients on the rolls in the Lithium clinic, Madurai Medical College and Govt. Rajaji Hospital, Madurai, India, 47 patients suffering from affective disorders receiving lithium continuously for more than three years were analysed with a view to study the recurrences. Thirteen suffered no relapses while on lithium while nineteen experienced them while on lithium. Four were free from recurrences after lithium was withdrawn- Seven defaulted but suffered recurrences while in four the drug was withdrawn and in both the groups remission was achieved with re-administration of lithium. The study reveals that lithium besides averting the recurrences can reduce the frequency, number, duration, intensity of episodes and improve the amenability to drugs. Among the symptoms, suicidal ideas and behaviour and insight were found to be influenced favourably by lithium. Among the factors that help favourable response to lithium were a positive family history of affective disorder, in the first degree relatives and lesser frequency and number of episodes in the pre-lithium period. A reappraisal of the natural history of the illness is called for in the light of lithium prophylaxis of manic depressive psychosis. PMID:21965880

  14. Lithium attenuates lead induced toxicity on mouse non-adherent bone marrow cells.

    PubMed

    Banijamali, Mahsan; Rabbani-Chadegani, Azra; Shahhoseini, Maryam

    2016-07-01

    Lead is a poisonous heavy metal that occurs in all parts of environment and causes serious health problems in humans. The aim of the present study was to investigate the possible protective effect of lithium against lead nitrate induced toxicity in non-adherent bone marrow stem cells. Trypan blue and MTT assays represented that exposure of the cells to different concentrations of lead nitrate decreased viability in a dose dependent manner, whereas, pretreatment of the cells with lithium protected the cells against lead toxicity. Lead reduced the number and differentiation status of bone marrow-derived precursors when cultured in the presence of colony stimulating factor (CSF), while the effect was attenuated by lithium. The cells treated with lead nitrate exhibited cell shrinkage, DNA fragmentation, anion superoxide production, but lithium prevented lead action. Moreover, apoptotic indexes such as PARP cleavage and release of HMGB1 induced by lead, were protected by lithium, suggesting anti-apoptotic effect of lithium. Immunoblot analysis of histone H3K9 acetylation indicated that lithium overcame lead effect on acetylation. In conclusion, lithium efficiently reduces lead toxicity suggesting new insight into lithium action which may contribute to increased cell survival. It also provides a potentially new therapeutic strategy for lithium and a cost-effective approach to minimize destructive effects of lead on bone marrow stem cells. PMID:27259346

  15. 77 FR 28259 - Mailings of Lithium Batteries

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-05-14

    ... for mailpieces containing lithium metal or lithium-ion cells or batteries and applies regardless of...'' instead of ``lithium content'' for secondary lithium-ion batteries when describing maximum quantity limits...-ion (Rechargeable) Cells and Batteries Small consumer-type lithium-ion cells and batteries like...

  16. Lithium in the brines of Fish Lake Valley and Columbus Salt Marsh, Nevada

    USGS Publications Warehouse

    Smith, C.L.; Meier, Allen L.; Downey, H.D.

    1977-01-01

    Analyses of waters-from springs in Nevada have led to the identification of an area containing anomalous amounts of lithium northwest of the Clayton Valley-area. Fish Lake Valley and Columbus Salt Marsh contain waters having, relatively high lithium and potassium concentrations. At least a part of these waters is probably derived from the leaching of Tertiary rocks containing saline minerals. The high-lithium waters at Columbus Salt Marsh could be derived not only by the leaching of rocks with a high soluble lithium ands, potassium content but also by subsurface outflow from Fish Lake Valley.

  17. Development of Lithium CPS Based Limiters for Realization of a Concept of Closed Lithium Circulation Loop in Tokamak

    NASA Astrophysics Data System (ADS)

    Zharkov, M. Yu.; Vertkov, A. V.; Lyublinski, I. E.; Mirnov, S. V.; Lazarev, V. B.; Szherbak, A. N.

    Cooling of tokamak boundary plasma owing to radiation of non-fully stripped lithium ions is considered as a promising way for protection of plasma facing elements (PFE) in tokamak. It may be effectively realized when the main part of lithium ions are involved in the closed circuit of migration between plasma and PFE surface. Such an approach may be implemented with the use of lithium device whose hot (500-600 °C) area to be effected by plasma serves as a Li-emitter and the cold part (∼180 °C) as a Li-collector in the shadow. Capillary-pore system (CPS) provides the returning of collected and condensed lithium to emitting zone by capillary forces. The main goals of the last T-11 M lithium experiments were investigating Li ions transport in the tokamak scrape of layer (SOL) and their collecting by different kinds of limiters. The design of devices based on lithium CPS with different ratio of emitting/collecting area is the main subject of this paper.

  18. Fumed Silica-Based Single-Ion Nanocomposite Electrolyte for Lithium Batteries.

    PubMed

    Zhao, Hui; Jia, Zhe; Yuan, Wen; Hu, Heyi; Fu, Yanbao; Baker, Gregory L; Liu, Gao

    2015-09-01

    A composite lithium electrolyte composed of polyelectrolyte-grafted nanoparticles and polyethylene glycol dimethyl ether (PEGDME) is synthesized and characterized. Polyanions immobilized by the silica nanoparticles have reduced anion mobility. Composite nanoparticles grafted by poly(lithium 4-styrenesulfonate) only have moderate conductivity at 60 °C. Almost an order increase of the conductivity to ∼10(-6) S/cm is achieved by co-polymerization of the poly(ethylene oxide) methacrylate with sodium 4-styrenesulfonate, which enhances dissociation between lithium cation and polyanion and facilitates lithium ion transfer from the inner part of the polyelectrolyte layer. This composite electrolyte has the potential to suppress lithium dendrite growth and enable the use of lithium metal anode in rechargeable batteries. PMID:26264507

  19. Bioavailability of lithium from lithium citrate syrup versus conventional lithium carbonate tablets.

    PubMed

    Guelen, P J; Janssen, T J; De Witte, T C; Vree, T B; Benson, K

    1992-10-01

    The bioavailability of lithium citrate syrup was compared with that of regular lithium carbonate tablets in 18 healthy male human volunteers. Blood samples were collected up to 48 h after dosing. Lithium serum concentrations were determined by means of AAS. The absorption rate following oral administration of the syrup was greater (tmax 0.8 h) than following administration of regular tablets (tmax 1.4 h). Maximum lithium serum concentrations, however, were only about 10 per cent higher after syrup dosing and serum concentrations resulting from syrup and tablets were almost superimposable from 2 h after dosing. The terminal half-life of lithium was found to be 22 h after syrup as well as after tablet dosing. No side-effects were observed during the study. The bioavailability of lithium from syrup relative to tablets was found to be bioequivalent with respect to the maximum lithium serum concentration and the extent of drug absorption (AUC). PMID:1489941

  20. Lithium disulfide battery

    DOEpatents

    Kaun, Thomas D.

    1988-01-01

    A negative electrode limited secondary electrochemical cell having dense FeS.sub.2 positive electrode operating exclusively on the upper plateau, a Li alloy negative electrode and a suitable lithium-containing electrolyte. The electrolyte preferably is 25 mole percent LiCl, 38 mole percent LiBr and 37 mole percent KBr. The cell may be operated isothermally.

  1. Lithium ion conducting electrolytes

    DOEpatents

    Angell, C. Austen; Liu, Changle

    1996-01-01

    A liquid, predominantly lithium-conducting, ionic electrolyte having exceptionally high conductivity at temperatures of 100.degree. C. or lower, including room temperature, and comprising the lithium salts selected from the group consisting of the thiocyanate, iodide, bromide, chloride, perchlorate, acetate, tetrafluoroborate, perfluoromethane sulfonate, perfluoromethane sulfonamide, tetrahaloaluminate, and heptahaloaluminate salts of lithium, with or without a magnesium-salt selected from the group consisting of the perchlorate and acetate salts of magnesium. Certain of the latter embodiments may also contain molecular additives from the group of acetonitrile (CH.sub.3 CN) succinnonitrile (CH.sub.2 CN).sub.2, and tetraglyme (CH.sub.3 --O--CH.sub.2 --CH.sub.2 --O--).sub.2 (or like solvents) solvated to a Mg.sup.+2 cation to lower the freezing point of the electrolyte below room temperature. Other particularly useful embodiments contain up to about 40, but preferably not more than about 25, mol percent of a long chain polyether polymer dissolved in the lithium salts to provide an elastic or rubbery solid electrolyte of high ambient temperature conductivity and exceptional 100.degree. C. conductivity. Another embodiment contains up to about but not more than 10 mol percent of a molecular solvent such as acetone.

  2. Lithium ion conducting electrolytes

    DOEpatents

    Angell, C.A.; Liu, C.

    1996-04-09

    A liquid, predominantly lithium-conducting, ionic electrolyte is described having exceptionally high conductivity at temperatures of 100 C or lower, including room temperature, and comprising the lithium salts selected from the group consisting of the thiocyanate, iodide, bromide, chloride, perchlorate, acetate, tetrafluoroborate, perfluoromethane sulfonate, perfluoromethane sulfonamide, tetrahaloaluminate, and heptahaloaluminate salts of lithium, with or without a magnesium-salt selected from the group consisting of the perchlorate and acetate salts of magnesium. Certain of the latter embodiments may also contain molecular additives from the group of acetonitrile (CH{sub 3}CN), succinnonitrile (CH{sub 2}CN){sub 2}, and tetraglyme (CH{sub 3}--O--CH{sub 2}--CH{sub 2}--O--){sub 2} (or like solvents) solvated to a Mg{sup +2} cation to lower the freezing point of the electrolyte below room temperature. Other particularly useful embodiments contain up to about 40, but preferably not more than about 25, mol percent of a long chain polyether polymer dissolved in the lithium salts to provide an elastic or rubbery solid electrolyte of high ambient temperature conductivity and exceptional 100 C conductivity. Another embodiment contains up to about but not more than 10 mol percent of a molecular solvent such as acetone. 2 figs.

  3. Lithium and Pregnancy

    MedlinePlus

    ... role in the rate of miscarriage, which include maternal age, gestational age, and history of previous miscarriage that ... Studies on children up to seven years of age who were exposed to lithium during pregnancy did not find significant physical, mental, or behavioral ...

  4. Lithium thionyl chloride battery

    SciTech Connect

    Saathoff, D.J.; Venkatasetty, H.V.

    1982-10-19

    The discharge rate and internal conductivity of electrochemical cell including a lithium anode, and a cathode and an electrolyte including LiAlCl4 and SOC2 is improved by the addition of an amount of a mixture containing AlCl3 and butyl pyridinium chloride.

  5. Lithium battery discharge tests

    NASA Technical Reports Server (NTRS)

    Johnson, C. J.

    1980-01-01

    The long term discharge of a variety of lithium cells was characterized and the susceptibility of the cells to chemical variation during the slow discharge was tested. A shunt resistor was set across the terminals to monitor the voltage as a function of time. Failures were identified by premature voltage drops.

  6. Dependence of recycling and edge profiles on lithium evaporation in high triangularity, high performance NSTX H-mode discharges

    NASA Astrophysics Data System (ADS)

    Maingi, R.; Osborne, T. H.; Bell, M. G.; Bell, R. E.; Boyle, D. P.; Canik, J. M.; Diallo, A.; Kaita, R.; Kaye, S. M.; Kugel, H. W.; LeBlanc, B. P.; Sabbagh, S. A.; Skinner, C. H.; Soukhanovskii, V. A.

    2015-08-01

    In this paper, the effects of a pre-discharge lithium evaporation variation on highly shaped discharges in the National Spherical Torus Experiment (NSTX) are documented. Lithium wall conditioning ('dose') was routinely applied onto graphite plasma facing components between discharges in NSTX, partly to reduce recycling. Reduced Dα emission from the lower and upper divertor and center stack was observed, as well as reduced midplane neutral pressure; the magnitude of reduction increased with the pre-discharge lithium dose. Improved energy confinement, both raw τE and H-factor normalized to scalings, with increasing lithium dose was also observed. At the highest doses, we also observed elimination of edge-localized modes. The midplane edge plasma profiles were dramatically altered, comparable to lithium dose scans at lower shaping, where the strike point was farther from the lithium deposition centroid. This indicates that the benefits of lithium conditioning should apply to the highly shaped plasmas planned in NSTX-U.

  7. International strategic minerals inventory summary report; lithium

    USGS Publications Warehouse

    Anstett, T.F.; Krauss, U.H.; Ober, J.A.; Schmidt, H.W.

    1990-01-01

    Major world resources of lithium are described in this summary report of information in the International Strategic Minerals Inventory (ISMI). ISMI is a cooperative data-collection effort of earth-science and mineral-resource agencies in Australia, Canada, the Federal Republic of Germany, the Republic of South Africa, the United Kingdom, and the United States of America. Part I of this report presents an overview of the resources and potential supply of lithium on the basis of inventory information; Part II contains tables of some of the geologic information and mineral-resource information and production data collected by ISMI participants. In terms of lithium-resource availability, present economically viable resources are more than sufficient to meet likely demand in the foreseeable future. In times of excess capacity such as currently exist, some pegmatite operations cannot compete with brine operations, which are less costly. A further production shift from pegmatites to brines will result in the concentration of supply in a few countries such as Chile and the United States. This shift would lead to the dependence of industrialized countries on deliveries from these sources.

  8. Geospatial examination of lithium in drinking water and suicide mortality

    PubMed Central

    2012-01-01

    Background Lithium as a substance occurring naturally in food and drinking water may exert positive effects on mental health. In therapeutic doses, which are more than 100 times higher than natural daily intakes, lithium has been proven to be a mood-stabilizer and suicide preventive. This study examined whether natural lithium content in drinking water is regionally associated with lower suicide rates. Methods Previous statistical approaches were challenged by global and local spatial regression models taking spatial autocorrelation as well as non-stationarity into account. A Geographically Weighted Regression model was applied with significant independent variables as indicated by a spatial autoregressive model. Results The association between lithium levels in drinking water and suicide mortality can be confirmed by the global spatial regression model. In addition, the local spatial regression model showed that the association was mainly driven by the eastern parts of Austria. Conclusions According to old anecdotic reports the results of this study support the hypothesis of positive effects of natural lithium intake on mental health. Both, the new methodological approach and the results relevant for health may open new avenues in the collaboration between Geographic Information Science, medicine, and even criminology, such as exploring the spatial association between violent or impulsive crime and lithium content in drinking water. PMID:22695110

  9. The history of lithium therapy

    PubMed Central

    Shorter, Edward

    2013-01-01

    The use of lithium in psychiatry goes back to the mid-19th century. Early work, however, was soon forgotten, and John Cade is credited with reintroducing lithium to psychiatry for mania in 1949. Mogens Schou undertook a randomly controlled trial for mania in 1954, and in the course of that study became curious about lithium as a prophylactic for depressive illness. In 1970, the United States became the 50th country to admit lithium to the marketplace. Meanwhile, interest in lithium for the prophylaxis of depression was growing apace and today the agent is widely prescribed for that indication, even though it has not been accepted by the Food and Drug Administration. Lithium was almost derailed by a small group of opponents from the Maudsley Hospital and its status today is threatened by the “mood stabilizers.” PMID:19538681

  10. Experimental lithium system. Final report

    SciTech Connect

    Kolowith, R.; Berg, J.D.; Miller, W.C.

    1985-04-01

    A full-scale mockup of the Fusion Materials Irradiation Test (FMIT) Facility lithium system was built at the Hanford Engineering Development Laboratory (HEDL). This isothermal mockup, called the Experimental Lithium System (ELS), was prototypic of FMIT, excluding the accelerator and dump heat exchanger. This 3.8 m/sup 3/ lithium test loop achieved over 16,000 hours of safe and reliable operation. An extensive test program demonstrated satisfactory performance of the system components, including the HEDL-supplied electromagnetic lithium pump, the lithium jet target, the purification and characterization hardware, as well as the auxiliary argon and vacuum systems. Experience with the test loop provided important information on system operation, performance, and reliability. This report presents a complete overview of the entire Experimental Lithium System test program and also includes a summary of such areas as instrumentation, coolant chemistry, vapor/aerosol transport, and corrosion.

  11. Membranes in Lithium Ion Batteries

    PubMed Central

    Yang, Min; Hou, Junbo

    2012-01-01

    Lithium ion batteries have proven themselves the main choice of power sources for portable electronics. Besides consumer electronics, lithium ion batteries are also growing in popularity for military, electric vehicle, and aerospace applications. The present review attempts to summarize the knowledge about some selected membranes in lithium ion batteries. Based on the type of electrolyte used, literature concerning ceramic-glass and polymer solid ion conductors, microporous filter type separators and polymer gel based membranes is reviewed. PMID:24958286

  12. LITHIUM TOXICITY - A DESCRIPTIVE STUDY

    PubMed Central

    Kumar, Ratanendra; Deb, Jayant Kumar; Sinha, Baxi Neeraj Prasad; Sinha, Vinod Kumar

    2001-01-01

    Lithium is the treatment for acute mania and bipolar disorders. Ever since its introduction in the psychiatric arsenal, case reports of toxicity have been appearing in the literature at regular intervals. This study was thus carried out to study the presentation and associated features of lithium toxicity. In this retrospective study, case record files of all patients suspected to have developed lithium toxicity during a five year period were retrieved. It was found that toxicity presented most commonly with cerebellar symptoms and appeared at lower serum levels. Lithium could be restarted albeit at a lower dose and with a gradual titration in a number of cases. PMID:21407839

  13. Lithium batteries with laminar anodes

    SciTech Connect

    Bruder, A.H.

    1986-11-04

    This patent describes a laminar electrical cell, comprising an anode, a cathode, and an electrolyte permeable separator between the anode and the cathode. The anode consists essentially of a layer of lithium having at least one surface of unreacted lithium metal in direct contact with and adhered to a layer of conductive plastic with no intermediate adhesive promoting adjuncts. The cathode comprises a slurry of MnO/sub 2/ and carbon particles in a solution of a lithium salt in an organic solvent, the solution permeating the separator and being in contact with the lithium.

  14. Lithium in rocks from the Lincoln, Helena, and Townsend areas, Montana

    USGS Publications Warehouse

    Brenner-Tourtelot, Elizabeth F.; Meier, Allen L.; Curtis, Craig A.

    1978-01-01

    In anticipation of increased demand for lithium for energy-related uses, the U.S. Geological Survey has been appraising the lithium resources of the United States and investigating occurrences of lithium. Analyses of samples of chiefly lacustrine rocks of Oligocene age collected by M. R. Mudge near Lincoln, Mont. showed as much as 1,500 ppm lithium. Since then we have sampled the area in greater detail, and have sampled rocks of similar ages in the Helena and Townsend valleys. The lithium-rich beds crop out in a band about 1.3 km long by 0.3 km wide near the head of Beaver Creek, about 14 km northwest of Lincoln, Mont. These beds consist of laminated marlstone, oil shale, carbonaceous shale, limestone, conglomerate, and tuff. Some parts of this sequence average almost 0.1 percent lithium. The lithium-bearing rocks are too low in grade and volume to be economic. Samples of sedimentary rocks of Oligocene age from the Helena and Townsend valleys in the vicinity of Helena, Mont. were generally low in lithium (3-40 ppm). However, samples of rhyolites from the western side of the Helena valley and from the Lava Mountain area were slightly above average in lithium content (6-200 ppm).

  15. Separator for lithium batteries and lithium batteries including the separator

    SciTech Connect

    Foster, D.L.

    1989-03-14

    A multilayer separator is described for preventing the internal shorting of lithium batteries, the multilayer separator including porous membranes and an electroactive polymeric material contained within the separator layers wherein the polymer is one that will react with any lithium dendrites that could penetrate the separator thus preventing an internal short circuit of the cell.

  16. Parameter estimation for lithium ion batteries

    NASA Astrophysics Data System (ADS)

    Santhanagopalan, Shriram

    With an increase in the demand for lithium based batteries at the rate of about 7% per year, the amount of effort put into improving the performance of these batteries from both experimental and theoretical perspectives is increasing. There exist a number of mathematical models ranging from simple empirical models to complicated physics-based models to describe the processes leading to failure of these cells. The literature is also rife with experimental studies that characterize the various properties of the system in an attempt to improve the performance of lithium ion cells. However, very little has been done to quantify the experimental observations and relate these results to the existing mathematical models. In fact, the best of the physics based models in the literature show as much as 20% discrepancy when compared to experimental data. The reasons for such a big difference include, but are not limited to, numerical complexities involved in extracting parameters from experimental data and inconsistencies in interpreting directly measured values for the parameters. In this work, an attempt has been made to implement simplified models to extract parameter values that accurately characterize the performance of lithium ion cells. The validity of these models under a variety of experimental conditions is verified using a model discrimination procedure. Transport and kinetic properties are estimated using a non-linear estimation procedure. The initial state of charge inside each electrode is also maintained as an unknown parameter, since this value plays a significant role in accurately matching experimental charge/discharge curves with model predictions and is not readily known from experimental data. The second part of the dissertation focuses on parameters that change rapidly with time. For example, in the case of lithium ion batteries used in Hybrid Electric Vehicle (HEV) applications, the prediction of the State of Charge (SOC) of the cell under a variety of

  17. Solid lithium-ion electrolyte

    DOEpatents

    Zhang, J.G.; Benson, D.K.; Tracy, C.E.

    1998-02-10

    The present invention relates to the composition of a solid lithium-ion electrolyte based on the Li{sub 2}O--CeO{sub 2}--SiO{sub 2} system having good transparent characteristics and high ion conductivity suitable for uses in lithium batteries, electrochromic devices and other electrochemical applications. 12 figs.

  18. Intercell connector for lithium batteries

    SciTech Connect

    Bruder, A.H.

    1984-10-16

    Laminar batteries of series connected cells comprising lithium anodes and an electrolyte containing a passivating solvent reactive with lithium in which the cells are electrically connected in series by intercell barriers comprising outer layers of electrochemically inert electronically conducting material in contact with the electrochemically active anode and cathode of adjacent cells and a layer of metal foil between the electrochemically inert layers.

  19. Solid lithium-ion electrolyte

    DOEpatents

    Zhang, Ji-Guang; Benson, David K.; Tracy, C. Edwin

    1998-01-01

    The present invention relates to the composition of a solid lithium-ion electrolyte based on the Li.sub.2 O--CeO.sub.2 --SiO.sub.2 system having good transparent characteristics and high ion conductivity suitable for uses in lithium batteries, electrochromic devices and other electrochemical applications.

  20. Progress in secondary lithium batteries

    NASA Technical Reports Server (NTRS)

    Holleck, G. L.

    1982-01-01

    The lithium/molybdenum trisulfide system is discussed. This system has a higher potential energy density than that of lithium/titanium disulfide. Possible energy densities and performance values for cells, projected from preliminary data obtained on small cells, are summarized. The electrode structure is emphasized as an important factor in the decreasing of capacity upon cycling.

  1. Improved Carbon Anodes For Rechargeable Lithium Cells

    NASA Technical Reports Server (NTRS)

    Huang, Chen-Kuo; Surampudi, Subbarao; Attia, Alan; Halpert, Gerald

    1994-01-01

    Carbon anodes for rechargeable lithium cells improved by choosing binder contents and fabrication conditions to achieve maximum porosity, uniform loading, and maximum reversible lithium capacity. Stacking electrodes under pressure during assembly of cells increases cyclability of lithium. Rechargeable, high-energy-density lithium cells containing improved carbon anodes find use in spacecraft, military, communications, automotive, and other demanding applications.

  2. Lithium Treatment for Psychiatric Disorders

    PubMed Central

    Maletzky, Barry M.; Shore, James H.

    1978-01-01

    Although used around the world since 1949, lithium has come into extensive use in psychiatry in the United States only within the past decade. Before initiating treatment with this drug, physicians must be familiar with the diagnostic scheme of the major affective disorders, the indications and contraindications to lithium's use, and its principles of treatment, including evaluation before lithium therapy, criteria for monitoring blood levels and signs of impending toxicity. Despite earlier reports about the toxicity of lithium when it was promoted as a salt substitute, lithium is a safe drug. Its use not only has revolutionized the treatment of the major affective disorders, but has opened up new and broad avenues of research into the regulation of man's emotions. PMID:664651

  3. HOW RELIABLE IS 24 HOUR SERUM LITHIUM LEVEL AFTER A TEST DOSE OF LITHIUM IN PREDICTING OPTIMAL LITHIUM DOSE?

    PubMed Central

    Kuruvilla, K.; Shaji, K.S.

    1989-01-01

    SUMMARY 57% of a group of 35 patients treated with Lithium Carbonate at dosages predicted by the nomogram suggested by Cooper et al (1973) failed to reach therapeutic levels of serum lithium. This finding casts serious doubts on the usefulness of the claim by Cooper et al (1973 & 1976) that 24 hour serum lithium level after a test dose of 600 mg. lithium can predict the daily lithium dose. PMID:21927360

  4. Lithium orotate, carbonate and chloride: pharmacokinetics, polyuria in rats.

    PubMed Central

    Smith, D F

    1976-01-01

    1 The pharmacokinetics of the lithium ion administered as lithium orotate were studied in rats. Parallel studies were carried out with lithium carbonate and lithium chloride. 2 No differences in the uptake, distribution and excretion of the lithium ion were observed between lithium orotate, lithium carbonate and lithium chloride after single intraperitoneal, subcutaneous or intragastric injections (0.5-1.0 mEq lithium/kg) or after administration of the lithium salts for 20 days in the food. 3 The findings oppose the notion that the pharmacokinetics of the lithium ion given as lithium orotate differ from lithium chloride or lithium carbonate. 4 Polyuria and polydipsia developed more slowly in rats given lithium orotate than in those given lithium carbonate or lithium chloride, perhaps due to an effect of the orotate anion. PMID:1260219

  5. Lithium Coatings on NSTX Plasma Facing Components and Its Effects On Boundary Control, Core Plasma Performance, and Operation

    SciTech Connect

    H.W.Kugel, M.G.Bell, H.Schneider, J.P.Allain, R.E.Bell, R Kaita, J.Kallman, S. Kaye, B.P. LeBlanc, D. Mansfield, R.E. Nygen, R. Maingi, J. Menard, D. Mueller, M. Ono, S. Paul, S.Gerhardt, R.Raman, S.Sabbagh, C.H.Skinner, V.Soukhanovskii, J.Timberlake, L.E.Zakharov, and the NSTX Research Team

    2010-01-25

    NSTX high-power divertor plasma experiments have used in succession lithium pellet injection (LPI), evaporated lithium, and injected lithium powder to apply lithium coatings to graphite plasma facing components. In 2005, following wall conditioning and LPI, discharges exhibited edge density reduction and performance improvements. Since 2006, first one, and now two lithium evaporators have been used routinely to evaporate lithium onto the lower divertor region at total rates of 10-70 mg/min for periods 5-10 min between discharges. Prior to each discharge, the evaporators are withdrawn behind shutters. Significant improvements in the performance of NBI heated divertor discharges resulting from these lithium depositions were observed. These evaporators are now used for more than 80% of NSTX discharges. Initial work with injecting fine lithium powder into the edge of NBI heated deuterium discharges yielded comparable changes in performance. Several operational issues encountered with lithium wall conditions, and the special procedures needed for vessel entry are discussed. The next step in this work is installation of a Liquid Lithium Divertor surface on the outer part of the lower divertor.

  6. Lithium coatings on NSTX plasma facing components and its effects on boundary control, core plasma performance, and operation

    SciTech Connect

    Kugel, H. W.; Bell, M. G.; Maingi, R.

    2010-01-01

    NSTX high power divertor plasma experiments have used in succession lithium pellet injection (LPI), evaporated lithium, and injected lithium powder to apply lithium coatings to graphite plasma facing components. In 2005, following the wall conditioning and LPI, discharges exhibited edge density reduction and performance improvements. Since 2006, first one, and now two lithium evaporators have been used routinely to evaporate lithium onto the lower divertor region at total rates of 10-70 mg/min for periods 5-10 min between discharges. Prior to each discharge, the evaporators are withdrawn behind shutters. Significant improvements in the performance of NBI heated divertor discharges resulting from these lithium depositions were observed. These evaporators are now used for more than 80% of NSTX discharges. Initial work with injecting fine lithium powder into the edge of NBI heated deuterium discharges yielded comparable changes in performance. Several operational issues encountered with lithium wall conditions, and the special procedures needed for vessel entry are discussed. The next step in this work is installation of a liquid lithium divertor surface on the outer part of the lower divertor.

  7. Lithium niobate explosion monitor

    DOEpatents

    Bundy, C.H.; Graham, R.A.; Kuehn, S.F.; Precit, R.R.; Rogers, M.S.

    1990-01-09

    Monitoring explosive devices is accomplished with a substantially z-cut lithium niobate crystal in abutment with the explosive device. Upon impact by a shock wave from detonation of the explosive device, the crystal emits a current pulse prior to destruction of the crystal. The current pulse is detected by a current viewing transformer and recorded as a function of time in nanoseconds. In order to self-check the crystal, the crystal has a chromium film resistor deposited thereon which may be heated by a current pulse prior to detonation. This generates a charge which is detected by a charge amplifier. 8 figs.

  8. Lithium niobate explosion monitor

    DOEpatents

    Bundy, Charles H.; Graham, Robert A.; Kuehn, Stephen F.; Precit, Richard R.; Rogers, Michael S.

    1990-01-01

    Monitoring explosive devices is accomplished with a substantially z-cut lithium niobate crystal in abutment with the explosive device. Upon impact by a shock wave from detonation of the explosive device, the crystal emits a current pulse prior to destruction of the crystal. The current pulse is detected by a current viewing transformer and recorded as a function of time in nanoseconds. In order to self-check the crystal, the crystal has a chromium film resistor deposited thereon which may be heated by a current pulse prior to detonation. This generates a charge which is detected by a charge amplifier.

  9. Halo Star Lithium Depletion

    SciTech Connect

    Pinsonneault, M. H.; Walker, T. P.; Steigman, G.; Narayanan, Vijay K.

    1999-12-10

    The depletion of lithium during the pre-main-sequence and main-sequence phases of stellar evolution plays a crucial role in the comparison of the predictions of big bang nucleosynthesis with the abundances observed in halo stars. Previous work has indicated a wide range of possible depletion factors, ranging from minimal in standard (nonrotating) stellar models to as much as an order of magnitude in models that include rotational mixing. Recent progress in the study of the angular momentum evolution of low-mass stars permits the construction of theoretical models capable of reproducing the angular momentum evolution of low-mass open cluster stars. The distribution of initial angular momenta can be inferred from stellar rotation data in young open clusters. In this paper we report on the application of these models to the study of lithium depletion in main-sequence halo stars. A range of initial angular momenta produces a range of lithium depletion factors on the main sequence. Using the distribution of initial conditions inferred from young open clusters leads to a well-defined halo lithium plateau with modest scatter and a small population of outliers. The mass-dependent angular momentum loss law inferred from open cluster studies produces a nearly flat plateau, unlike previous models that exhibited a downward curvature for hotter temperatures in the 7Li-Teff plane. The overall depletion factor for the plateau stars is sensitive primarily to the solar initial angular momentum used in the calibration for the mixing diffusion coefficients. Uncertainties remain in the treatment of the internal angular momentum transport in the models, and the potential impact of these uncertainties on our results is discussed. The 6Li/7Li depletion ratio is also examined. We find that the dispersion in the plateau and the 6Li/7Li depletion ratio scale with the absolute 7Li depletion in the plateau, and we use observational data to set bounds on the 7Li depletion in main-sequence halo

  10. Method of recycling lithium borate to lithium borohydride through methyl borate

    DOEpatents

    Filby, Evan E.

    1977-01-01

    This invention provides a method for the recycling of lithium borate to lithium borohydride which can be reacted with water to generate hydrogen for utilization as a fuel. The lithium borate by-product of the hydrogen generation reaction is reacted with hydrogen chloride and water to produce boric acid and lithium chloride. The boric acid and lithium chloride are converted to lithium borohydride through a methyl borate intermediate to complete the recycle scheme.

  11. Lithium abundance in a sample of solar-like stars

    NASA Astrophysics Data System (ADS)

    López-Valdivia, R.; Hernández-Águila, J. B.; Bertone, E.; Chávez, M.; Cruz-Saenz de Miera, F.; Amazo-Gómez, E. M.

    2015-08-01

    We report on the determination of the lithium abundance [A(Li)] of 52 solar-like stars. For 41 objects the A(Li) here presented corresponds to the first measurement. We have measured the equivalent widths of the 6708 Å lithium feature in high-resolution spectroscopic images (R ˜ 80 000), obtained at the Observatorio Astrofísico Guillermo Haro (Sonora, Mexico), as part of the first scientific observations of the revitalized Lunar and Planetary Laboratory (LPL) Echelle Spectrograph, now known as the Cananea High-resolution Spectrograph (CanHiS). Lithium abundances were derived with the Fortran code MOOG, using as fundamental input a set of atmospheric parameters recently obtained by our group. With the help of an additional small sample with previous A(Li) determinations, we demonstrate that our lithium abundances are in agreement, to within uncertainties, with other works. Two target objects stand out from the rest of the sample. The star BD+47 3218 (Teff = 6050 ± 52 K, A(Li) = 1.86 ± 0.07 dex) lies inside the so-called lithium desert in the A(Li)-Teff plane. The other object, BD+28 4515, has an A(Li) = 3.05 ± 0.07 dex, which is the highest of our sample and compatible with the expected abundances of relatively young stars.

  12. [Lithium gluconate 8% in the treatment of seborrheic dermatitis].

    PubMed

    Dréno, B; Blouin, E; Moyse, D

    2007-04-01

    Seborrheic dermatitis is a chronic from of inflammatory dermatitis characterized by erythema and desquamation with predominant localization on the face (nasolabial folds, eyebrows, hair-line and ears). It appears to be caused by proliferation of Malassezia yeasts. Lithium gluconate 8% gel (Lithioderm 8% gel) is the only drug containing topical lithium salt commercially available in France for the treatment of seborrheic dermatitis. The mechanism of action of topical lithium is not well known; it may act through anti-inflammatory and antifungal action. Efficacy and safety were assessed in 2 clinical studies, one versus placebo and the other versus ketoconazole 2% foaming gel using the same principal criterion defined as the rate of patients showing complete remission after 2 months of treatment (complete disappearance of both erythema and desquamation). Lithium gluconate 8% was significantly more effective than placebo and than ketoconazole 2% foaming gel and was well tolerated. Adverse events observed were cutaneous (burning sensation, erythema and pruritus), for the most part of mild severity. No cutaneous side effects contributed to those reported with the use of systemic lithium in psychiatric disorders were noted. Pharmacokinetic studies have shown that systemic absorption after topical application is low. Lithioderm 8% gel is applied twice daily over a recommended period of 2 months. It constitutes a new alternative in the treatment of facial seborrheic dermatitis, regardless of severity. PMID:17483754

  13. A Spectroscopic Measurement of Recycling on the Surface of a Liquid Lithium Limiter in CDX-U

    NASA Astrophysics Data System (ADS)

    Marfuta, P.; Kaita, R.; Majeski, R.; Soukhanovskii, V.; Maingi, R.

    2003-10-01

    Spectroscopic measurements of lithium plasma-facing surfaces should give a quantitative assessment of the local recycling in CDX-U. We will use both a 1-D CCD camera with an interference filter and a pair of fiber-optic filterscopes focused on different parts of a fully-toroidal liquid lithium limiter tray. Additional filterscope data will be taken along a sightline immediately above the tray, so that the edge plasma emission can be subtracted from the direct views of the lithium surface. The diagnostics will measure the H-alpha line both with and without lithium in the limiter tray to assess the reduction of neutral hydrogen recycling, as well as the Li-I emission to observe the level of lithium introduced into the plasma, and the C-III and O-II lines to measure the effect of the lithium on plasma impurities.

  14. Fewer metabolites of dietary choline reach the blood of rats after treatment with lithium

    SciTech Connect

    Pomfret, E.A.; O'Connor, S.C.; Zola, T.H.; Zeisel, S.H.

    1988-01-01

    The authors studies the effect of lithium treatment upon the appearance in blood, liver and intestine of metabolites formed from dietary choline. Rats were treated for 9 days with 2 mEq/kg lithium carbonate or water. Animals were fasted overnight, and on the 10th day were fed with a solution containing radiolabeled choline chloride. The lithium treated groups also received 2.0 mEq/kg lithium as part of this solution. After an oral dose of 1 ml of a 1 mM choline solution, the lithium-treated animals had significantly lower levels of choline derived radiolabel in blood than did controls at 30, 60, 120, and 180 minutes (47%, 51%, 59% and 74%, respectively). They observed similar decreases of the accumulation in blood, at 180 minutes after the dose, of choline-derived radiolabel when choline was administered at lower or higher concentrations. After an oral treatment containing 0.1, 1 or 10 mM choline, lithium treated animals accumulated 69%, 66% and 72% as much radiolabel in serum as did controls. Most of the radiolabel found in blood at 180 minutes was in metabolites of choline which are formed within liver. The diminished accumulation of radiolabel in serum after lithium treatment was not due to increased accumulation of label by erythrocytes, liver or gut wall. They suggest that lithium influences the release by liver of betaine and phosphatidylcholine. 36 references, 5 figures.

  15. A lithium superionic conductor.

    PubMed

    Kamaya, Noriaki; Homma, Kenji; Yamakawa, Yuichiro; Hirayama, Masaaki; Kanno, Ryoji; Yonemura, Masao; Kamiyama, Takashi; Kato, Yuki; Hama, Shigenori; Kawamoto, Koji; Mitsui, Akio

    2011-09-01

    Batteries are a key technology in modern society. They are used to power electric and hybrid electric vehicles and to store wind and solar energy in smart grids. Electrochemical devices with high energy and power densities can currently be powered only by batteries with organic liquid electrolytes. However, such batteries require relatively stringent safety precautions, making large-scale systems very complicated and expensive. The application of solid electrolytes is currently limited because they attain practically useful conductivities (10(-2) S cm(-1)) only at 50-80 °C, which is one order of magnitude lower than those of organic liquid electrolytes. Here, we report a lithium superionic conductor, Li(10)GeP(2)S(12) that has a new three-dimensional framework structure. It exhibits an extremely high lithium ionic conductivity of 12 mS cm(-1) at room temperature. This represents the highest conductivity achieved in a solid electrolyte, exceeding even those of liquid organic electrolytes. This new solid-state battery electrolyte has many advantages in terms of device fabrication (facile shaping, patterning and integration), stability (non-volatile), safety (non-explosive) and excellent electrochemical properties (high conductivity and wide potential window). PMID:21804556

  16. Lithium ion conducting ionic electrolytes

    DOEpatents

    Angell, C.A.; Xu, K.; Liu, C.

    1996-01-16

    A liquid, predominantly lithium-conducting, ionic electrolyte is described which has exceptionally high conductivity at temperatures of 100 C or lower, including room temperature. It comprises molten lithium salts or salt mixtures in which a small amount of an anionic polymer lithium salt is dissolved to stabilize the liquid against recrystallization. Further, a liquid ionic electrolyte which has been rubberized by addition of an extra proportion of anionic polymer, and which has good chemical and electrochemical stability, is described. This presents an attractive alternative to conventional salt-in-polymer electrolytes which are not cationic conductors. 4 figs.

  17. Lithium ion conducting ionic electrolytes

    DOEpatents

    Angell, C. Austen; Xu, Kang; Liu, Changle

    1996-01-01

    A liquid, predominantly lithium-conducting, ionic electrolyte is described which has exceptionally high conductivity at temperatures of 100.degree. C. or lower, including room temperature. It comprises molten lithium salts or salt mixtures in which a small amount of an anionic polymer lithium salt is dissolved to stabilize the liquid against recrystallization. Further, a liquid ionic electrolyte which has been rubberized by addition of an extra proportion of anionic polymer, and which has good chemical and electrochemical stability, is described. This presents an attractive alternative to conventional salt-in-polymer electrolytes which are not cationic conductors.

  18. Anodes for rechargeable lithium batteries

    DOEpatents

    Thackeray, Michael M.; Kepler, Keith D.; Vaughey, John T.

    2003-01-01

    A negative electrode (12) for a non-aqueous electrochemical cell (10) with an intermetallic host structure containing two or more elements selected from the metal elements and silicon, capable of accommodating lithium within its crystallographic host structure such that when the host structure is lithiated it transforms to a lithiated zinc-blende-type structure. Both active elements (alloying with lithium) and inactive elements (non-alloying with lithium) are disclosed. Electrochemical cells and batteries as well as methods of making the negative electrode are disclosed.

  19. A Lithium Superionic Sulfide Cathode for Lithium-Sulfur Batteries

    SciTech Connect

    Lin, Zhan; Liu, Zengcai; Dudney, Nancy J; Liang, Chengdu

    2013-01-01

    This work presents a facile synthesis approach for core-shell structured Li2S nanoparticles, which have Li2S as the core and Li3PS4 as the shell. This material functions as lithium superionic sulfide (LSS) cathode for long-lasting, energy-efficient lithium-sulfur (Li-S) batteries. The LSS has an ionic conductivity of 10-7 S cm-1 at 25 oC, which is 6 orders of magnitude higher than that of bulk Li2S (~10-13 S cm-1). The high lithium-ion conductivity of LSS imparts an excellent cycling performance to all-solid Li-S batteries, which also promises safe cycling of high-energy batteries with metallic lithium anodes.

  20. Cyanoethylated Compounds as Additives in Lithium/Lithium Ion Batteries

    SciTech Connect

    Nagasubramanian, Ganesan

    1998-05-08

    The power loss of lithium/lithium ion battery cells is significantly reduced, especially at low temperatures, when about 1% by weight of an additive is incorporated in the electrolyte layer of the cells. The usable additives are organic solvent soluble cyanoethylated polysaccharides and poly(vinyl alcohol). The power loss decrease results primarily from the decrease in the charge transfer resistance at the interface between the electrolyte and the cathode.

  1. Lithium metal doped electrodes for lithium-ion rechargeable chemistry

    DOEpatents

    Liu, Gao; Battaglia, Vince; Wang, Lei

    2016-09-13

    An embodiment of the invention combines the superior performance of a polyvinylidene difluoride (PVDF) or polyethyleneoxide (POE) binder, the strong binding force of a styrene-butadiene (SBR) binder, and a source of lithium ions in the form of solid lithium metal powder (SLMP) to form an electrode system that has improved performance as compared to PVDF/SBR binder based electrodes. This invention will provide a new way to achieve improved results at a much reduced cost.

  2. Cyanoethylated compounds as additives in lithium/lithium batteries

    DOEpatents

    Nagasubramanian, Ganesan

    1999-01-01

    The power loss of lithium/lithium ion battery cells is significantly reduced, especially at low temperatures, when about 1% by weight of an additive is incorporated in the electrolyte layer of the cells. The usable additives are organic solvent soluble cyanoethylated polysaccharides and poly(vinyl alcohol). The power loss decrease results primarily from the decrease in the charge transfer resistance at the interface between the electrolyte and the cathode.

  3. Silica Precipitation and Lithium Sorption

    SciTech Connect

    Jay Renew

    2015-09-20

    This file contains silica precipitation and lithium sorption data from the project. The silica removal data is corrected from the previous submission. The previous submission did not take into account the limit of detection of the ICP-MS procedure.

  4. 21 CFR 862.3560 - Lithium test system.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Lithium test system. 862.3560 Section 862.3560....3560 Lithium test system. (a) Identification. A lithium test system is a device intended to measure lithium (from the drug lithium carbonate) in serum or plasma. Measurements of lithium are used to...

  5. 21 CFR 862.3560 - Lithium test system.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Lithium test system. 862.3560 Section 862.3560....3560 Lithium test system. (a) Identification. A lithium test system is a device intended to measure lithium (from the drug lithium carbonate) in serum or plasma. Measurements of lithium are used to...

  6. 21 CFR 862.3560 - Lithium test system.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Lithium test system. 862.3560 Section 862.3560....3560 Lithium test system. (a) Identification. A lithium test system is a device intended to measure lithium (from the drug lithium carbonate) in serum or plasma. Measurements of lithium are used to...

  7. 21 CFR 862.3560 - Lithium test system.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Lithium test system. 862.3560 Section 862.3560....3560 Lithium test system. (a) Identification. A lithium test system is a device intended to measure lithium (from the drug lithium carbonate) in serum or plasma. Measurements of lithium are used to...

  8. Modeling the Lithium Ion Battery

    ERIC Educational Resources Information Center

    Summerfield, John

    2013-01-01

    The lithium ion battery will be a reliable electrical resource for many years to come. A simple model of the lithium ions motion due to changes in concentration and voltage is presented. The battery chosen has LiCoO[subscript 2] as the cathode, LiPF[subscript 6] as the electrolyte, and LiC[subscript 6] as the anode. The concentration gradient and…

  9. Air breathing lithium power cells

    DOEpatents

    Farmer, Joseph C.

    2014-07-15

    A cell suitable for use in a battery according to one embodiment includes a catalytic oxygen cathode; a stabilized zirconia electrolyte for selective oxygen anion transport; a molten salt electrolyte; and a lithium-based anode. A cell suitable for use in a battery according to another embodiment includes a catalytic oxygen cathode; an electrolyte; a membrane selective to molecular oxygen; and a lithium-based anode.

  10. Early North American research on lithium.

    PubMed

    Johnson, G; Gershon, S

    1999-12-01

    Research and clinical interest in lithium in the USA lagged behind that in Europe, largely because of the experience of deaths due to lithium in cardiac patients. The first American report on lithium was published in 1960 by Sam Gershon, the Australian psychiatrist who had undertaken lithium studies in Melbourne in conjunction with the physiologist Trautner. Major USA clinical trials originated in the 1960s; and the clinical significance of lithium was recognised in a special section in the American Journal of Psychiatry in 1968. The US Food and Drug Administration (FDA) approval of lithium for control of manic episodes was finally given in 1970. PMID:10622180

  11. Lithium compensation for full cell operation

    DOEpatents

    Xiao, Jie; Zheng, Jianming; Chen, Xilin; Lu, Dongping; Liu, Jun; Jiguang, Jiguang

    2016-05-17

    Disclosed herein are embodiments of a lithium-ion battery system comprising an anode, an anode current collector, and a layer of lithium metal in contact with the current collector, but not in contact with the anode. The lithium compensation layer dissolves into the electrolyte to compensate for the loss of lithium ions during usage of the full cell. The specific placement of the lithium compensation layer, such that there is no direct physical contact between the lithium compensation layer and the anode, provides certain advantages.

  12. Dendrite preventing separator for secondary lithium batteries

    NASA Technical Reports Server (NTRS)

    Shen, David H. (Inventor); Surampudi, Subbarao (Inventor); Huang, Chen-Kuo (Inventor); Halpert, Gerald (Inventor)

    1993-01-01

    Dendrites are prevented from shorting a secondary lithium battery by use of a first porous separator, such as porous polypropylene, adjacent to the lithium anode that is unreactive with lithium and a second porous fluoropolymer separator between the cathode and the first separator, such as polytetrafluoroethylene, that is reactive with lithium. As the tip of a lithium dendrite contacts the second separator, an exothermic reaction occurs locally between the lithium dendrite and the fluoropolymer separator. This results in the prevention of the dendrite propagation to the cathode.

  13. Dendrite preventing separator for secondary lithium batteries

    NASA Technical Reports Server (NTRS)

    Shen, David H. (Inventor); Surampudi, Subbarao (Inventor); Huang, Chen-Kuo (Inventor); Halpert, Gerald (Inventor)

    1995-01-01

    Dendrites are prevented from shorting a secondary lithium battery by use of a first porous separator such as porous polypropylene adjacent the lithium anode that is unreactive with lithium and a second porous fluoropolymer separator between the cathode and the first separator such as polytetrafluoroethylene that is reactive with lithium. As the tip of a lithium dendrite contacts the second separator, an exothermic reaction occurs locally between the lithium dendrite and the fluoropolymer separator. This results in the prevention of the dendrite propagation to the cathode.

  14. Secondary lithium batteries for space applications

    NASA Technical Reports Server (NTRS)

    Carter, B.; Khanna, S. K.; Yen, S. P. S.; Shen, D.; Somoano, R. B.

    1981-01-01

    Secondary lithium cells which use a LiAsF6-2-Me-THF electrolyte and a TiS2 intercalatable cathode exhibit encouraging cycle life at ambient temperature. Electrochemical and surface analytical studies indicate that the electrolyte is unstable in the presence of metallic lithium, leading to the formation of a lithium passivating film composed of lithium arsenic oxyfluorides and lithium fluorsilicates. The lithium cyclability remains as the most important problem to solve. Different electrolyte solvents, such as sulfolane, exhibit promising characteristics but lead to new compatibility problems with the other cell component materials.

  15. Modeling Diffusion Induced Stresses for Lithium-Ion Battery Materials

    NASA Astrophysics Data System (ADS)

    Chiu Huang, Cheng-Kai

    rate (C-rate) during charging/discharging affects diffusion induced stresses inside electrode materials. For the experimental part we first conduct charging/discharging under different C-rates to observe the voltage responses for commercial LiFePO4 batteries. Then Time-of-Flight Secondary Ion Mass Spectrometry technique is applied to measure the lithium ion intensities in different C-rate charged/discharged samples. These experimental results could be used to support that a more significant voltage fluctuation under high C-rates is due to different lithium insertion mechanisms, rather than the amount of lithium ions intercalated into electrode materials. Thus the investigation of C-rate-dependent stress evolution is required for the development of a more durable lithium ion battery. In this dissertation, we extend the single particle finite element model to investigate the C-rate-dependent diffusion induced stresses in a multi-particle system. Concentration dependent anisotropic material properties, C-rate-dependent volume misfits and concentration dependent Li-ion diffusivity are incorporated in the model. The concentration gradients, diffusion induced stresses, and strain energies under different C-rates are discussed in this study. Particle fractures have been observed in many experimental results, in this study we further discuss the effect of the crack surface orientation on the lithium concentration profile and stress level in cathode materials. The results of this dissertation provide a better understanding of diffusion induced stresses in electrode materials and contribute to our fundamental knowledge of interplay between lithium intercalations, stress evolutions, particle fractures and the capacity fade in lithium-ion batteries.

  16. Lithium peroxide primary element

    SciTech Connect

    Winsel, A.

    1982-05-04

    In a galvanic primary element of the system Li/H/sub 2/O/sub 2/, the aqueous cathode depolarizer H/sub 2/O/sub 2/ is fixated as a polyurethane gel. It can thereby be controlled and caused to react with the anode metal in accordance with the current drain requirements. This is accomplished using a ram to press the gel toward a conductor which covers the lithium anode, which may take the form of a metal grid and/or a gas diffusion electrode. The oxygen which forms in the working layer through catalytic decomposition of hydrogen peroxide creates a gas bubble when the current is interrupted or the ram is stopped, thereby interrupting the further supply of hydrogen peroxide to the catalyst.

  17. Development of a lithium liquid metal ion source for MeV ion beam analysis

    SciTech Connect

    Read, P.M.; Maskrey, J.T.; Alton, G.D.

    1988-01-01

    Lithium liquid metal ion sources are an attractive complement to the existing gaseous ion sources that are extensively used for ion beam analysis. This is due in part to the high brightness of the liquid metal ion source and in part to the availability of a lithium ion beam. High brightness is of particular importance to MeV ion microprobes which are now approaching current density limitations on targets determined by the ion source. The availability of a lithium beam provides increased capabilities for hydrogen profiling and high resolution Rutherford backscattering spectrometry. This paper describes the design and performance of a lithium liquid metal ion source suitable for use on a 5MV Laddertron accelerator. Operational experience with the source and some of its uses for ion beam analysis are discussed. 8 refs., 2 figs.

  18. Comparative analysis of ex-situ and operando X-ray diffraction experiments for lithium insertion materials

    NASA Astrophysics Data System (ADS)

    Brant, William R.; Li, Dan; Gu, Qinfen; Schmid, Siegbert

    2016-01-01

    A comparative study of ex-situ and operando X-ray diffraction techniques using the fast lithium ion conductor Li0.18Sr0.66Ti0.5Nb0.5O3 is presented. Ex-situ analysis of synchrotron X-ray diffraction data suggests that a single phase material exists for all discharges to as low as 0.422 V. For samples discharged to 1 V or lower, i.e. with higher lithium content, it is possible to determine the lithium position from the X-ray data. However, operando X-ray diffraction from a coin cell reveals that a kinetically driven two phase region occurs during battery cycling below 1 V. Through monitoring the change in unit cell dimension during electrochemical cycling the dynamics of lithium insertion are explored. A reduction in the rate of unit cell expansion of 22(2)% part way through the first discharge and 13(1)% during the second discharge is observed. This reduction may be caused by a drop in lithium diffusion into the bulk material for higher lithium contents. A more significant change is a jump in the unit cell expansion by 60(2)% once the lithium content exceeds one lithium ion per vacant site. It is suggested that this jump is caused by damping of octahedral rotations, thus establishing a link between lithium content and octahedral rotations.

  19. A new lithium salt with dihydroxybenzene and lithium tetrafluoroborate for lithium battery electrolytes

    NASA Astrophysics Data System (ADS)

    Xue, Zhao-Ming; Sun, Bin-Bin; Zhou, Wei; Chen, Chun-Hua

    2011-10-01

    A new unsymmetrical lithium salt containing F-, C6H4O22- [dianion of 1,2-benzenediol], lithium difluoro(1,2-benzene-diolato(2-)-o,o‧)borate (LDFBDB) is synthesized and characterized. Its thermal decomposition in nitrogen begins at 170 °C. The cyclic voltammetry study shows that the LDFBDB solution in propylene carbonate (PC) is stable up to 3.7 V versus Li+/Li. It is soluble in common organic solvents. The ionic dissociation properties of LDFBDB are examined by conductivity measurements in PC, PC+ ethyl methyl carbonate (EMC), PC + dimethyl ether (DME), PC + ethylene carbonate (EC) + EMC solutions. The conductivity values of the 0.564 mol dm-3 LDFBDB electrolyte in PC + DME solution is 3.90 mS cm-1. All these properties of the new lithium salt including the thermal characteristics, electrochemical stabilities, solubilities, ionic dissociation properties are studied and compared with those of its derivatives, lithium difluoro(3-fluoro-1,2-benzene-diolato(2-)-o,o‧)borate (FLDFBDB), lithium [3-fluoro-1,2-benzenediolato(2-)-o,o‧ oxalato]borate (FLBDOB), and lithium bis(oxalate)borate (LBOB).

  20. Lithium sputtering from lithium-coated plasma facing components in the NSTX divertor

    NASA Astrophysics Data System (ADS)

    Scotti, F.; Soukhanovskii, V. A.; Ahn, J.-W.; Bell, R. E.; Gerhardt, S. P.; Jaworski, M. A.; Kaita, R.; Kugel, H. W.; McLean, A. G.; Meier, E. T.; Podestà, M.; Roquemore, A. L.

    2015-08-01

    Lithium sputtering yields and gross impurity influxes from lithium-coated graphite and molybdenum plasma facing components (PFCs) have been analyzed for the first time in the National Spherical Torus Experiment (NSTX) divertor during H-mode NBI-heated discharges. Motivated by the beneficial effects of lithium conditioning on discharge performance and reproducibility, evaporative lithium coatings were the routine wall conditioning technique in NSTX. Neutral lithium sputtering yields from solid lithium coatings in NSTX were found to be consistent with values reported from test stand experiments from deuterium-saturated lithium (with sputtering yields YLi ∼ 0.03- 0.07). Temperature-enhanced lithium sputtering was observed on lithium-coated graphite and molybdenum as a result of PFC heating by both embedded heaters and incident plasma heat flux, leading to YLi ∼ 0.1- 0.2 for surface temperatures above the lithium melting point.

  1. Protective lithium ion conducting ceramic coating for lithium metal anodes and associate method

    DOEpatents

    Bates, John B.

    1994-01-01

    A battery structure including a cathode, a lithium metal anode and an electrolyte disposed between the lithium anode and the cathode utilizes a thin-film layer of lithium phosphorus oxynitride overlying so as to coat the lithium anode and thereby separate the lithium anode from the electrolyte. If desired, a preliminary layer of lithium nitride may be coated upon the lithium anode before the lithium phosphorous oxynitride is, in turn, coated upon the lithium anode so that the separation of the anode and the electrolyte is further enhanced. By coating the lithium anode with this material lay-up, the life of the battery is lengthened and the performance of the battery is enhanced.

  2. High performance discharges in the Lithium Tokamak eXperiment with liquid lithium walls

    SciTech Connect

    Schmitt, J. C.; Bell, R. E.; Boyle, D. P.; Esposti, B.; Kaita, R.; Kozub, T.; LeBlanc, B. P.; Lucia, M.; Maingi, R.; Majeski, R.; Merino, E.; Punjabi-Vinoth, S.; Tchilingurian, G.; Capece, A.; Koel, B.; Roszell, J.; Biewer, T. M.; Gray, T. K.; Kubota, S.; Beiersdorfer, P.; and others

    2015-05-15

    The first-ever successful operation of a tokamak with a large area (40% of the total plasma surface area) liquid lithium wall has been achieved in the Lithium Tokamak eXperiment (LTX). These results were obtained with a new, electron beam-based lithium evaporation system, which can deposit a lithium coating on the limiting wall of LTX in a five-minute period. Preliminary analyses of diamagnetic and other data for discharges operated with a liquid lithium wall indicate that confinement times increased by 10× compared to discharges with helium-dispersed solid lithium coatings. Ohmic energy confinement times with fresh lithium walls, solid and liquid, exceed several relevant empirical scaling expressions. Spectroscopic analysis of the discharges indicates that oxygen levels in the discharges limited on liquid lithium walls were significantly reduced compared to discharges limited on solid lithium walls. Tokamak operations with a full liquid lithium wall (85% of the total plasma surface area) have recently started.

  3. Non-aqueous electrolytes for lithium batteries

    SciTech Connect

    Bakos, V.W.; Steklenski, D.J.

    1989-02-14

    An electrochemical cell is described comprising a lithium anode, a cathode and an electrolyte having a conductivity, and reciprocal ohms per cm, of at least 3.5 in, comprising a lithium salt, propylene carbonate and 1,2-dimethoxypropane.

  4. Michael Thackeray on Lithium-air Batteries

    SciTech Connect

    Thackeray, Michael

    2009-01-01

    Michael Thackeray, Distinguished Fellow at Argonne National Laboratory, speaks on the new technology Lithium-air batteries, which could potentially increase energy density by 5-10 times over lithium-ion batteries.

  5. Michael Thackeray on Lithium-air Batteries

    ScienceCinema

    Thackeray, Michael

    2013-04-19

    Michael Thackeray, Distinguished Fellow at Argonne National Laboratory, speaks on the new technology Lithium-air batteries, which could potentially increase energy density by 5-10 times over lithium-ion batteries.

  6. Khalil Amine on Lithium-air Batteries

    ScienceCinema

    Khalil Amine

    2010-01-08

    Khalil Amine, materials scientist at Argonne National Laboratory, speaks on the new technology Lithium-air batteries, which could potentially increase energy density by 5-10 times over lithium-ion batteries.

  7. Khalil Amine on Lithium-air Batteries

    SciTech Connect

    Khalil Amine

    2009-09-14

    Khalil Amine, materials scientist at Argonne National Laboratory, speaks on the new technology Lithium-air batteries, which could potentially increase energy density by 5-10 times over lithium-ion batteries.

  8. Nuclear quantum effects in water exchange around lithium and fluoride ions

    SciTech Connect

    Wilkins, David M.; Manolopoulos, David; Dang, Liem X.

    2015-02-14

    We employ classical and ring polymer molecular dynamics simulations to study the effect of nuclear quantum fluctuations on the structure and the water exchange dynamics of aqueous solutions of lithium and fluoride ions. While we obtain reasonably good agreement with experimental data for solutions of lithium by augmenting the Coulombic interactions between the ion and the water molecules with a standard Lennard-Jones ion-oxygen potential, the same is not true for solutions of fluoride, for which we find that a potential with a softer repulsive wall gives much better agreement. A small degree of destabilization of the first hydration shell is found in quantum simulations of both ions when compared with classical simulations, with the shell becoming less sharply defined and the mean residence time of the water molecules in the shell decreasing. In line with these modest differences, we find that the mechanisms of the water exchange reactions are unaffected by quantization, so a classical description of these reactions gives qualitatively correct and quantitatively reasonable results. We also find that the quantum effects in solutions of lithium are larger than in solutions of fluoride. This is partly due to the stronger interaction of lithium with water molecules, partly due to the lighter mass of lithium, and partly due to competing quantum effects in the hydration of fluoride, which are absent in the hydration of lithium. LXD was supported by US Department of Energy, Office of Science, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences, and Biosciences.

  9. Nuclear quantum effects in water exchange around lithium and fluoride ions

    SciTech Connect

    Wilkins, David M.; Manolopoulos, David E.; Dang, Liem X.

    2015-02-14

    We employ classical and ring polymer molecular dynamics simulations to study the effect of nuclear quantum fluctuations on the structure and the water exchange dynamics of aqueous solutions of lithium and fluoride ions. While we obtain reasonably good agreement with experimental data for solutions of lithium by augmenting the Coulombic interactions between the ion and the water molecules with a standard Lennard-Jones ion-oxygen potential, the same is not true for solutions of fluoride, for which we find that a potential with a softer repulsive wall gives much better agreement. A small degree of destabilization of the first hydration shell is found in quantum simulations of both ions when compared with classical simulations, with the shell becoming less sharply defined and the mean residence time of the water molecules in the shell decreasing. In line with these modest differences, we find that the mechanisms of the exchange processes are unaffected by quantization, so a classical description of these reactions gives qualitatively correct and quantitatively reasonable results. We also find that the quantum effects in solutions of lithium are larger than in solutions of fluoride. This is partly due to the stronger interaction of lithium with water molecules, partly due to the lighter mass of lithium and partly due to competing quantum effects in the hydration of fluoride, which are absent in the hydration of lithium.

  10. Multi-layered, chemically bonded lithium-ion and lithium/air batteries

    SciTech Connect

    Narula, Chaitanya Kumar; Nanda, Jagjit; Bischoff, Brian L; Bhave, Ramesh R

    2014-05-13

    Disclosed are multilayer, porous, thin-layered lithium-ion batteries that include an inorganic separator as a thin layer that is chemically bonded to surfaces of positive and negative electrode layers. Thus, in such disclosed lithium-ion batteries, the electrodes and separator are made to form non-discrete (i.e., integral) thin layers. Also disclosed are methods of fabricating integrally connected, thin, multilayer lithium batteries including lithium-ion and lithium/air batteries.

  11. Complete atrioventricular block secondary to lithium therapy.

    PubMed

    Shiraki, Teruo; Kohno, Kunihisa; Saito, Daiji; Takayama, Hiroki; Fujimoto, Akira

    2008-05-01

    Sinus node dysfunction has been reported most frequently among the adverse cardiovascular effects of lithium. In the present case, complete atrioventricular (AV) block with syncopal attacks developed secondary to lithium therapy, necessitating permanent pacemaker implantation. Serum lithium levels remained under or within the therapeutic range during the syncopal attacks. Lithium should be used with extreme caution, especially in patients with mild disturbance of AV conduction. PMID:18441470

  12. Novel Electrolytes for Lithium Ion Batteries

    SciTech Connect

    Lucht, Brett L

    2014-12-12

    We have been investigating three primary areas related to lithium ion battery electrolytes. First, we have been investigating the thermal stability of novel electrolytes for lithium ion batteries, in particular borate based salts. Second, we have been investigating novel additives to improve the calendar life of lithium ion batteries. Third, we have been investigating the thermal decomposition reactions of electrolytes for lithium-oxygen batteries.

  13. Cardiovascular malformations with lithium use during pregnancy.

    PubMed

    Weinstein, M R; Goldfield, M

    1975-05-01

    The 143 cases of lithium use during pregnancy collected by the Register of Lithium Babies show that infants exposed to lithium appear to have a higher than expected ratio of cardiovascular anomalies to all anomalies and may have an increased risk of congenital heart disease. The authors believe that these findings justify a conservative policy on the use of lithium with fertile and pregnant women. PMID:1119612

  14. Rechargeable lithium battery technology - A survey

    NASA Technical Reports Server (NTRS)

    Halpert, Gerald; Surampudi, Subbarao

    1990-01-01

    The technology of the rechargeable lithium battery is discussed with special attention given to the types of rechargeable lithium cells and to their expected performance and advantages. Consideration is also given to the organic-electrolyte and polymeric-electrolyte cells and to molten salt lithium cells, as well as to technical issues, such as the cycle life, charge control, rate capability, cell size, and safety. The role of the rechargeable lithium cell in future NASA applications is discussed.

  15. Primary lithium batteries, some consumer considerations

    NASA Technical Reports Server (NTRS)

    Bro, P.

    1983-01-01

    In order to determine whether larger size lithium batteries would be commercially marketable, the performance of several D size lithium batteries was compared with that of an equivalent alkaline manganese battery, and the relative costs of the different systems were compared. It is concluded that opportunities exist in the consumer market for the larger sizes of the low rate and moderate rate lithium batteries, and that the high rate lithium batteries need further improvements before they can be recommended for consumer applications.

  16. Aplastic anemia associated with lithium therapy

    PubMed Central

    Hussain, M. Z.; Khan, A. G.; Chaudhry, Z. A.

    1973-01-01

    A case is reported of fatal aplastic anemia developing in a 50-year-old woman who received lithium carbonate in the generally accepted dosage for a manic-depressive disorder. The serum lithium had been determined at regular intervals and never exceeded what is considered a safe level. Patients for whom lithium is prescribed should have periodic hematologic examinations. PMID:4691107

  17. Solid composite electrolytes for lithium batteries

    DOEpatents

    Kumar, Binod; Scanlon, Jr., Lawrence G.

    2000-01-01

    Solid composite electrolytes are provided for use in lithium batteries which exhibit moderate to high ionic conductivity at ambient temperatures and low activation energies. In one embodiment, a ceramic-ceramic composite electrolyte is provided containing lithium nitride and lithium phosphate. The ceramic-ceramic composite is also preferably annealed and exhibits an activation energy of about 0.1 eV.

  18. Anode materials for lithium-ion batteries

    DOEpatents

    Sunkara, Mahendra Kumar; Meduri, Praveen; Sumanasekera, Gamini

    2014-12-30

    An anode material for lithium-ion batteries is provided that comprises an elongated core structure capable of forming an alloy with lithium; and a plurality of nanostructures placed on a surface of the core structure, with each nanostructure being capable of forming an alloy with lithium and spaced at a predetermined distance from adjacent nanostructures.

  19. Army position on lithium battery safety

    NASA Technical Reports Server (NTRS)

    Reiss, E.

    1982-01-01

    User requirements for lithium sulfur batteries are presented. They include careful analysis of design and quality control, along with certain equipment specifications. Some of the specifications include: hermetically sealed cells; lithium limited cells with stoichiometry of lithium to sulfur dioxide as a ratio of one; low moisture content in the cells; and battery capacity.

  20. NASA/Marshall's lithium battery applications

    NASA Technical Reports Server (NTRS)

    Paschal, L. E.

    1980-01-01

    A general lithium battery is described and a summary of lithium battery applications is presented. Four aspects of a particular lithium battery, the inducement environmental contamination monitoring battery, are discussed-design and construction details, thermal vacuum tests, projection tests, and acceptance tests.

  1. Magnetism in lithium-oxygen discharge product.

    PubMed

    Lu, Jun; Jung, Hun-Ji; Lau, Kah Chun; Zhang, Zhengcheng; Schlueter, John A; Du, Peng; Assary, Rajeev S; Greeley, Jeffrey; Ferguson, Glen A; Wang, Hsien-Hau; Hassoun, Jusef; Iddir, Hakim; Zhou, Jigang; Zuin, Lucia; Hu, Yongfeng; Sun, Yang-Kook; Scrosati, Bruno; Curtiss, Larry A; Amine, Kahlil

    2013-07-01

    Nonaqueous lithium-oxygen batteries have a much superior theoretical gravimetric energy density compared to conventional lithium-ion batteries, and thus could render long-range electric vehicles a reality. A molecular-level understanding of the reversible formation of lithium peroxide in these batteries, the properties of major/minor discharge products, and the stability of the nonaqueous electrolytes is required to achieve successful lithium-oxygen batteries. We demonstrate that the major discharge product formed in the lithium-oxygen cell, lithium peroxide, exhibits a magnetic moment. These results are based on dc-magnetization measurements and a lithium-oxygen cell containing an ether-based electrolyte. The results are unexpected because bulk lithium peroxide has a significant band gap. Density functional calculations predict that superoxide-type surface oxygen groups with unpaired electrons exist on stoichiometric lithium peroxide crystalline surfaces and on nanoparticle surfaces; these computational results are consistent with the magnetic measurement of the discharged lithium peroxide product as well as EPR measurements on commercial lithium peroxide. The presence of superoxide-type surface oxygen groups with spin can play a role in the reversible formation and decomposition of lithium peroxide as well as the reversible formation and decomposition of electrolyte molecules. PMID:23670967

  2. Conductive lithium storage electrode

    DOEpatents

    Chiang, Yet-Ming; Chung, Sung-Yoon; Bloking, Jason T.; Andersson, Anna M.

    2008-03-18

    A compound comprising a composition A.sub.x(M'.sub.1-aM''.sub.a).sub.y(XD.sub.4).sub.z, A.sub.x(M'.sub.1-aM''.sub.a).sub.y(DXD.sub.4).sub.z, or A.sub.x(M'.sub.1-aM''.sub.a).sub.y(X.sub.2D.sub.7).sub.z, and have values such that x, plus y(1-a) times a formal valence or valences of M', plus ya times a formal valence or valence of M'', is equal to z times a formal valence of the XD.sub.4, X.sub.2D.sub.7, or DXD.sub.4 group; or a compound comprising a composition (A.sub.1-aM''.sub.a).sub.xM'.sub.y(XD.sub.4).sub.z, (A.sub.1-aM''.sub.a).sub.xM'.sub.y(DXD.sub.4).sub.z(A.sub.1-aM''.sub.a).s- ub.xM'.sub.y(X.sub.2D.sub.7).sub.z and have values such that (1-a).sub.x plus the quantity ax times the formal valence or valences of M'' plus y times the formal valence or valences of M' is equal to z times the formal valence of the XD.sub.4, X.sub.2D.sub.7 or DXD.sub.4 group. In the compound, A is at least one of an alkali metal and hydrogen, M' is a first-row transition metal, X is at least one of phosphorus, sulfur, arsenic, molybdenum, and tungsten, M'' any of a Group IIA, IIIA, IVA, VA, VIA, VIIA, VIIIA, IB, IIB, IIIB, IVB, VB, and VIB metal, D is at least one of oxygen, nitrogen, carbon, or a halogen, 0.0001lithium phosphate that can intercalate lithium or hydrogen. The compound can be used in an electrochemical device including electrodes and storage batteries and can have a gravimetric capacity of at least about 80 mAh/g while being charged/discharged at greater than about C rate of the compound.

  3. Conductive lithium storage electrode

    DOEpatents

    Chiang, Yet-Ming; Chung, Sung-Yoon; Bloking, Jason T.; Andersson, Anna M.

    2012-04-03

    A compound comprising a composition A.sub.x(M'.sub.1-aM''.sub.a).sub.y(XD.sub.4).sub.z, A.sub.x(M'.sub.1-aM''.sub.a).sub.y(DXD.sub.4).sub.z, or A.sub.x(M'.sub.1-aM''.sub.a).sub.y(X.sub.2D.sub.7).sub.z, and have values such that x, plus y(1-a) times a formal valence or valences of M', plus ya times a formal valence or valence of M'', is equal to z times a formal valence of the XD.sub.4, X.sub.2D.sub.7, or DXD.sub.4 group; or a compound comprising a composition (A.sub.1-aM''.sub.a).sub.xM'.sub.y(XD.sub.4).sub.z, (A.sub.1-aM''.sub.a).sub.xM'.sub.y(DXD.sub.4).sub.z (A.sub.1-aM''.sub.a).sub.xM'.sub.y(X.sub.2D.sub.7).sub.z and have values such that (1-a).sub.x plus the quantity ax times the formal valence or valences of M'' plus y times the formal valence or valences of M' is equal to z times the formal valence of the XD.sub.4, X.sub.2D.sub.7 or DXD.sub.4 group. In the compound, A is at least one of an alkali metal and hydrogen, M' is a first-row transition metal, X is at least one of phosphorus, sulfur, arsenic, molybdenum, and tungsten, M'' any of a Group IIA, IIIA, IVA, VA, VIA, VIIA, VIIIA, IB, IIB, IIIB, IVB, VB, and VIB metal, D is at least one of oxygen, nitrogen, carbon, or a halogen, 0.0001lithium phosphate that can intercalate lithium or hydrogen. The compound can be used in an electrochemical device including electrodes and storage batteries and can have a gravimetric capacity of at least about 80 mAh/g while being charged/discharged at greater than about C rate of the compound.

  4. The lithium vapor box divertor

    NASA Astrophysics Data System (ADS)

    Goldston, R. J.; Myers, R.; Schwartz, J.

    2016-02-01

    It has long been recognized that volumetric dissipation of the plasma heat flux from a fusion power system is preferable to its localized impingement on a material surface. Volumetric dissipation mitigates both the anticipated very high heat flux and intense particle-induced damage due to sputtering. Recent projections to a tokamak demonstration power plant suggest an immense upstream parallel heat flux, of order 20 GW m-2, implying that fully detached operation may be a requirement for the success of fusion power. Building on pioneering work on the use of lithium by Nagayama et al and by Ono et al as well as earlier work on the gas box divertor by Watkins and Rebut, we present here a concept for a lithium vapor box divertor, in which lithium vapor extracts momentum and energy from a fusion-power-plant divertor plasma, using fully volumetric processes. At the high powers and pressures that are projected this requires a high density of lithium vapor, which must be isolated from the main plasma in order to avoid lithium build-up on the chamber walls or in the plasma. Isolation is achieved through a powerful multi-box differential pumping scheme available only for condensable vapors. The preliminary box-wise calculations are encouraging, but much more work is required to demonstrate the practical viability of this scheme, taking into account at least 2D plasma and vapor flows within and between the vapor boxes and out of the vapor boxes to the main plasma.

  5. Lithium metal oxide electrodes for lithium cells and batteries

    DOEpatents

    Thackeray, Michael M.; Johnson, Christopher S.; Amine, Khalil; Kim, Jaekook

    2006-11-14

    A lithium metal oxide positive electrode for a non-aqueous lithium cell is disclosed. The cell is prepared in its initial discharged state and has a general formula xLiMO.sub.2.(1-x)Li.sub.2M'O.sub.3 in which 0

  6. Lithium metal oxide electrodes for lithium cells and batteries

    DOEpatents

    Thackeray, Michael M.; Johnson, Christopher S.; Amine, Khalil; Kim, Jaekook

    2004-01-13

    A lithium metal oxide positive electrode for a non-aqueous lithium cell is disclosed. The cell is prepared in its initial discharged state and has a general formula xLiMO.sub.2.(1-x)Li.sub.2 M'O.sub.3 in which 0

  7. Efficiency and Gamma Sensitivity of a Lithium Glass Neutron Detector

    NASA Astrophysics Data System (ADS)

    Wallace, Adam; Rees, Lawrence; Czirr, Bart; Hoggan, Margarita

    2010-10-01

    Neutron detectors are used in national security applications for detecting potential radioactive material entering the country. Due to the shortage of Helium-3 for neutron detectors, Lithium-6 glass scintillators could be a good material for a replacement detector. Lithium-6 has a large neutron capture cross section, which gives high neutron detection rates. Our detector is based on the fact that neutrons are captured by Lithium-6 which rapidly decays into an alpha particle and triton. Those particles induce scintillation in the glass scintillator and are detected in a photomultiplier tube. The orientation of the plastic and Lithium-6 glass changes the efficiency of the detector. Monte Carlo for Neutral Particles (MCNP) calculations have shown that increasing amounts of plastic provide more efficient neutron detection and that placing a layer of glass in the front of the detector is the ideal configuration. Homeland Security requires that a replacement for Helium-3 detectors must have low gamma sensitivity and high neutron detection efficiency. We are measuring the absolute gamma sensitivity of various arrangements of glass and plastic scintillator. Our goal is to meet the Department of Homeland Security requirement for gamma sensitivity of one part in 10,000.

  8. Lithium-6 foil neutron detector

    SciTech Connect

    Young, C.A.

    1982-12-21

    A neutron detection apparatus is provided which includes a selected number of flat surfaces of lithium-6 foil, and which further includes a gas mixture in contact with each of the flat surfaces for selectively reacting to charged particles emitted by or radiated from the lithium foil. A container is provided to seal the lithium foil and the gas mixture in a volume from which water vapor and atmospheric gases are excluded, the container having one or more walls which are transmissive to neutrons. Monitoring equipment in contact with the gas mixture detects reactions taking place in the gas mixture, and, in response to such reactions, provides notice of the flux of neutrons passing through the volume of the detector.

  9. Lithium ion rechargeable systems studies

    SciTech Connect

    Levy, S.C.; Lasasse, R.R.; Cygan, R.T.; Voigt, J.A.

    1995-02-01

    Lithium ion systems, although relatively new, have attracted much interest worldwide. Their high energy density, long cycle life and relative safety, compared with metallic lithium rechargeable systems, make them prime candidates for powering portable electronic equipment. Although lithium ion cells are presently used in a few consumer devices, e.g., portable phones, camcorders, and laptop computers, there is room for considerable improvement in their performance. Specific areas that need to be addressed include: (1) carbon anode--increase reversible capacity, and minimize passivation; (2) cathode--extend cycle life, improve rate capability, and increase capacity. There are several programs ongoing at Sandia National Laboratories which are investigating means of achieving the stated objectives in these specific areas. This paper will review these programs.

  10. Nanomaterials for rechargeable lithium batteries.

    PubMed

    Bruce, Peter G; Scrosati, Bruno; Tarascon, Jean-Marie

    2008-01-01

    Energy storage is more important today than at any time in human history. Future generations of rechargeable lithium batteries are required to power portable electronic devices (cellphones, laptop computers etc.), store electricity from renewable sources, and as a vital component in new hybrid electric vehicles. To achieve the increase in energy and power density essential to meet the future challenges of energy storage, new materials chemistry, and especially new nanomaterials chemistry, is essential. We must find ways of synthesizing new nanomaterials with new properties or combinations of properties, for use as electrodes and electrolytes in lithium batteries. Herein we review some of the recent scientific advances in nanomaterials, and especially in nanostructured materials, for rechargeable lithium-ion batteries. PMID:18338357

  11. Lithium ion rechargeable systems studies

    NASA Astrophysics Data System (ADS)

    Levy, Samuel C.; Lasasse, Robert R.; Cygan, Randall T.; Voigt, James A.

    Lithium ion systems, although relatively new, have attracted much interest worldwide. Their high energy density, long cycle life and relative safety, compared with metallic lithium rechargeable systems, make them prime candidates for powering portable electronic equipment. Although lithium ion cells are presently used in a few consumer devices, e.g., portable phones, camcorders, and laptop computers, there is room for considerable improvement in their performance. Specific areas that need to be addressed include: (1) carbon anode-increase reversible capacity, and minimize passivation; (2) cathode-extend cycle life, improve rate capability, and increase capacity. There are several programs ongoing at Sandia National Laboratories which are investigating means of achieving the stated objectives in these specific areas. This paper will review these programs.

  12. Thin-film Rechargeable Lithium Batteries

    DOE R&D Accomplishments Database

    Dudney, N. J.; Bates, J. B.; Lubben, D.

    1995-06-01

    Thin film rechargeable lithium batteries using ceramic electrolyte and cathode materials have been fabricated by physical deposition techniques. The lithium phosphorous oxynitride electrolyte has exceptional electrochemical stability and a good lithium conductivity. The lithium insertion reaction of several different intercalation materials, amorphous V{sub 2}O{sub 5}, amorphous LiMn{sub 2}O{sub 4}, and crystalline LiMn{sub 2}O{sub 4} films, have been investigated using the completed cathode/electrolyte/lithium thin film battery.

  13. Phthalocyanine cathode materials for secondary lithium cells

    SciTech Connect

    Tamaki, J.; Yamaji, A.

    1982-01-01

    Discharge and charge characteristics of various phthalocyanine cathodes coupled with lithium metal are studied. The best capacity based only on cathode active material weight is 1440 A-hr/kg in the lithium/iron phthalocyanine system, and the cycle life of the lithium/Cu phthalocyanine system is more than 100 times at the discharge depth of 157 A-hr/kg. The cathode reaction mechanism is supposed to be lithium intercalation between phthalocyanine molecules. The results indicate that these phthalocyanines are promising cathode active materials for lithium secondary batteries.

  14. Thin-film rechargeable lithium batteries

    SciTech Connect

    Dudney, N.J.; Bates, J.B.; Lubben, D.

    1995-06-01

    Thin-film rechargeable lithium batteries using ceramic electrolyte and cathode materials have been fabricated by physical deposition techniques. The lithium phosphorous oxynitride electrolyte has exceptional electrochemical stability and a good lithium conductivity. The lithium insertion reaction of several different intercalation materials, amorphous V{sub 2}O{sub 5}, amorphous LiMn{sub 2}O{sub 4}, and crystalline LiMn{sub 2}O{sub 4} films, have been investigated using the completed cathode/electrolyte/lithium thin-film battery.

  15. Spatial periphery of lithium isotopes

    SciTech Connect

    Galanina, L. I. Zelenskaja, N. S.

    2013-12-15

    The spatial structure of lithium isotopes is studied with the aid of the charge-exchange and (t, p) reactions on lithium nuclei. It is shown that an excited isobaric-analog state of {sup 6}Li (0{sup +}, 3.56MeV) has a halo structure formed by a proton and a neutron, that, in the {sup 9}Li nucleus, there is virtually no neutron halo, and that {sup 11}Li is a Borromean nucleus formed by a {sup 9}Li core and a two-neutron halo manifesting itself in cigar-like and dineutron configurations.

  16. Lithium synthesis in microquasar accretion.

    PubMed

    Iocco, Fabio; Pato, Miguel

    2012-07-13

    We study the synthesis of lithium isotopes in the hot tori formed around stellar mass black holes by accretion of the companion star. We find that sizable amounts of both stable isotopes 6Li and 7Li can be produced, the exact figures varying with the characteristics of the torus and reaching as much as 10(-2) M⊙ for each isotope. This mass output is enough to contaminate the entire Galaxy at a level comparable with the original, pregalactic amount of lithium and to overcome other sources such as cosmic-ray spallation or stellar nucleosynthesis. PMID:23030150

  17. Problem of the lithium peroxide thermal stability

    NASA Astrophysics Data System (ADS)

    Nefedov, R. A.; Ferapontov, Yu A.; Kozlova, N. P.

    2016-01-01

    The behavior of lithium peroxide and lithium peroxide monohydrate samples under heating in atmospheric air was studied by the method of thermogravimetric analysis (TGA) and differential thermal analysis (DTA). It was found that in the temperature range of 32°C to 82°C the interaction of lithium peroxides and steam with the formation of lithium peroxide monohydrate occurs, which was confirmed chemically and by X-ray Single-qualitative analysis. It was experimentally found that lithium peroxide starts to decompose into the lithium oxide and oxygen in the temperature range of 340 ÷ 348°C. It was established that the resulting thermal decomposition of lithium oxide, lithium peroxide at the temperature of 422°C melts with lithium carbonate eutecticly. The manifestation of polymorphism was not marked(seen or noticed) under the heating of studied samples of lithium peroxide and lithium peroxide monohydrate in the temperature range of 25°C ÷ 34°C.

  18. Towards quantum simulation and quantum sensing with strontium and lithium

    NASA Astrophysics Data System (ADS)

    Senaratne, Ruwan; Rajagopal, Shankari; Geiger, Zachary; Lebedev, Vyacheslav; Weld, David

    2013-05-01

    In this poster we describe progress towards the construction of two ultracold atomic physics experiments, based on bosonic and fermionic strontium and lithium. Applications of the experiments will include quantum simulation of quasicrystals, the development of novel cooling techniques, and force sensing on small length scales. We discuss hardware design, experimental features, and scientific goals. Work supported in part by AFOSR via a YIP award.

  19. Lithium conductivity in glasses of the Li2O-Al2O3-SiO2 system.

    PubMed

    Ross, Sebastian; Welsch, Anna-Maria; Behrens, Harald

    2015-01-01

    To improve the understanding of Li-dynamics in oxide glasses, i.e. the effect of [AlO4](-) tetrahedra and non-bridging oxygens on the potential landscape, electrical conductivity of seven fully polymerized and partly depolymerized lithium aluminosilicate glasses was investigated using impedance spectroscopy (IS). Lithium is the only mobile particle in these materials. Data derived from IS, i.e. activation energies, pre-exponential factors and diffusivities for lithium, are interpreted in light of Raman spectroscopic analyses of local structures in order to identify building units, which are crucial for lithium dynamics and migration. In polymerized glasses (compositional join LiAlSiO4-LiAlSi4O10) the direct current (DC) electrical conductivity continuously increases with increasing lithium content while lithium diffusivity is not affected by the Al/Si ratio in the glasses. Hence, the increase in electrical conductivity can be solely assigned to lithium concentration in the glasses. An excess of Li with respect to Al, i.e. the introduction of non-bridging oxygen into the network, causes a decrease in lithium mobility in the glasses. Activation energies in polymerized glasses (66 to 70 kJ mol(-1)) are significantly lower than those in depolymerized networks (76 to 78 kJ mol(-1)) while pre-exponential factors are nearly constant across all compositions. Comparison of the data with results for lithium silicates from the literature indicates a minimum in lithium diffusivity for glasses containing both aluminium tetrahedra and non-bridging oxygens. The findings allow a prediction of DC conductivity for a large variety of lithium aluminosilicate glass compositions. PMID:25406891

  20. Solid solution lithium alloy cermet anodes

    DOEpatents

    Richardson, Thomas J.

    2013-07-09

    A metal-ceramic composite ("cermet") has been produced by a chemical reaction between a lithium compound and another metal. The cermet has advantageous physical properties, high surface area relative to lithium metal or its alloys, and is easily formed into a desired shape. An example is the formation of a lithium-magnesium nitride cermet by reaction of lithium nitride with magnesium. The reaction results in magnesium nitride grains coated with a layer of lithium. The nitride is inert when used in a battery. It supports the metal in a high surface area form, while stabilizing the electrode with respect to dendrite formation. By using an excess of magnesium metal in the reaction process, a cermet of magnesium nitride is produced, coated with a lithium-magnesium alloy of any desired composition. This alloy inhibits dendrite formation by causing lithium deposited on its surface to diffuse under a chemical potential into the bulk of the alloy.

  1. Lithium Abundance in Planet Search Stars

    NASA Astrophysics Data System (ADS)

    Myles, Justin; Yale Exoplanets

    2016-01-01

    Since most lithium in the universe is primordial and is destroyed in stars, lithium abundance can be used as a stellar age indicator. Some research seems to show that planet formation may also affect lithium abundance in exoplanet host stars (EHS). However, small and heterogenous samples have made both of these phenomena unclear. Further study of lithium abundance in EHS is needed to better understand possible physical roles of lithium in planet formation theory. We use a large homogenous sample with accurate stellar parameters on which we will use equivalent width analysis to determine precise lithium abundances. From these abundance values we determine an age vs. abundance relation. Additionally, we aim to explore correlation between lithium abundance and planet formation.

  2. Surface protected lithium-metal-oxide electrodes

    DOEpatents

    Thackeray, Michael M.; Kang, Sun-Ho

    2016-04-05

    A lithium-metal-oxide positive electrode having a layered or spinel structure for a non-aqueous lithium electrochemical cell and battery is disclosed comprising electrode particles that are protected at the surface from undesirable effects, such as electrolyte oxidation, oxygen loss or dissolution by one or more lithium-metal-polyanionic compounds, such as a lithium-metal-phosphate or a lithium-metal-silicate material that can act as a solid electrolyte at or above the operating potential of the lithium-metal-oxide electrode. The surface protection significantly enhances the surface stability, rate capability and cycling stability of the lithium-metal-oxide electrodes, particularly when charged to high potentials.

  3. Photodisintegration of Lithium Isotopes

    NASA Astrophysics Data System (ADS)

    Wurtz, Ward Andrew

    We have performed a measurement of the photodisintegration of the lithium isotopes, 6Li and 7Li, using a monochromatic, polarised photon beam and a segmented neutron detector array which covers approximately ¼ of 4pi srad. Using time-of-flight and scintillator light-output spectra we separate the data into individual reaction channels. This work is motivated by the need to compare with recent theoretical predictions and to provide data for future theoretical work. For the photodisintegration of 6Li we took data at 12 photon energies between 8 and 35 MeV. We describe the data using a model consisting of two-body reaction channels and obtain angular distributions and absolute cross sections for many of these reaction channels. We compare our results with a recent Lorentz integral transform calculation (Bacca et al. Phys. Rev. C 69, 057001 (2004)). Our results are in reasonable agreement with the calculation, in contradiction with previous experimental results. For the photodisintegration of 7Li, we took data at 9 photon energies between 10 and 35 MeV. We obtain cross sections for the reaction channel 7Li + gamma → n + 6 Li(g.s.) at all photon energies with angular distributions at all but the highest energy. We obtain angular distributions and total cross sections for reaction channels involving excited states of the daughter nucleus, 6Li, at select energies. We hope that these measurements will provide incentive for new theoretical calculations. We observe neutrons that can only be described by the reaction channel 7Li + gamma → n + 6Li(10.0) which necessitates an excited state of 6Li with excitation energy Ex = 10.0 +/- 0.5 MeV that is not in the standard tables of excited states. ii

  4. Lithium-Induced Motor Neuropathy: An Unusual Presentation

    PubMed Central

    Mohapatra, Satyakam; Sahoo, Manas Ranjan; Rath, Neelmadhav

    2016-01-01

    Peripheral neuropathy secondary to lithium is under-recognized. Most cases of polyneuropathy were reported with lithium intoxication. However, very few cases were reported without lithium toxicity. We present a case of motor neuropathy due to the use of lithium in a 26-year-old male with a therapeutic lithium level. PMID:27335523

  5. 49 CFR 173.185 - Lithium cells and batteries.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 2 2012-10-01 2012-10-01 false Lithium cells and batteries. 173.185 Section 173... Class 7 § 173.185 Lithium cells and batteries. (a) Cells and batteries. A lithium cell or battery, including a lithium polymer cell or battery and a lithium-ion cell or battery, must conform to all of...

  6. 49 CFR 173.185 - Lithium cells and batteries.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 2 2013-10-01 2013-10-01 false Lithium cells and batteries. 173.185 Section 173... Class 7 § 173.185 Lithium cells and batteries. (a) Cells and batteries. A lithium cell or battery, including a lithium polymer cell or battery and a lithium-ion cell or battery, must conform to all of...

  7. 49 CFR 173.185 - Lithium cells and batteries.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 2 2011-10-01 2011-10-01 false Lithium cells and batteries. 173.185 Section 173... Class 7 § 173.185 Lithium cells and batteries. (a) Cells and batteries. A lithium cell or battery, including a lithium polymer cell or battery and a lithium-ion cell or battery, must conform to all of...

  8. Optical cleaning of congruent lithium niobate crystals

    NASA Astrophysics Data System (ADS)

    Kösters, M.; Sturman, B.; Werheit, P.; Haertle, D.; Buse, K.

    2009-09-01

    Lithium niobate (LiNbO3), also called the `silicon of photonics', is indispensable in advanced photonics and nonlinear optics. For many applications, however, the material is too polluted by transition metals, which are unavoidable at the parts per million level. These impurities serve as sources and traps for photoelectrons, causing optical damage and hampering the usability of LiNbO3. Efforts have therefore been made to get rid of the photoexcitable electrons. Here we introduce a method termed `optical cleaning'. We show theoretically and experimentally that, if the material is heated to moderate temperatures, allowing ions to migrate and to maintain charge neutrality, an appropriately moving light beam pushes photoexcitable electrons out of the illuminated region like a brush, and provides exponential cleaning. This promises purification levels that are beyond the reach of current technologies.

  9. Anode material for lithium batteries

    DOEpatents

    Belharouak, Ilias; Amine, Khalil

    2008-06-24

    Primary and secondary Li-ion and lithium-metal based electrochemical cell system. The suppression of gas generation is achieved through the addition of an additive or additives to the electrolyte system of respective cell, or to the cell itself whether it be a liquid, a solid- or plastized polymer electrolyte system. The gas suppression additives are primarily based on unsaturated hydrocarbons.

  10. Anode material for lithium batteries

    DOEpatents

    Belharouak, Ilias; Amine, Khalil

    2011-04-05

    Primary and secondary Li-ion and lithium-metal based electrochemical cell systems. The suppression of gas generation is achieved through the addition of an additive or additives to the electrolyte system of respective cell, or to the cell itself whether it be a liquid, a solid- or plasticized polymer electrolyte system. The gas suppression additives are primarily based on unsaturated hydrocarbons.

  11. Anode material for lithium batteries

    DOEpatents

    Belharouak, Ilias; Amine, Khalil

    2012-01-31

    Primary and secondary Li-ion and lithium-metal based electrochemical cell systems. The suppression of gas generation is achieved through the addition of an additive or additives to the electrolyte system of respective cell, or to the cell itself whether it be a liquid, a solid- or plasticized polymer electrolyte system. The gas suppression additives are primarily based on unsaturated hydrocarbons.

  12. Gelled Electrolytes For Lithium Batteries

    NASA Technical Reports Server (NTRS)

    Nagasubramanian, Ganesan; Attia, Alan; Halpert, Gerald

    1993-01-01

    Gelled polymer electrolyte consists of polyacrylonitrile (PAN), LiBF4, and propylene carbonate (PC). Thin films of electrolyte found to exhibit stable bulk conductivities of order of 10 to the negative 3rd power S/cm at room temperature. Used in thinfilm rechargeable lithium batteries having energy densities near 150 W h/kg.

  13. Lithium-loaded liquid scintillators

    DOEpatents

    Dai, Sheng; Kesanli, Banu; Neal, John S.

    2012-05-15

    The invention is directed to a liquid scintillating composition containing (i) one or more non-polar organic solvents; (ii) (lithium-6)-containing nanoparticles having a size of up to 10 nm and surface-capped by hydrophobic molecules; and (iii) one or more fluorophores. The invention is also directed to a liquid scintillator containing the above composition.

  14. Tradeoff analysis with lithium cells

    NASA Technical Reports Server (NTRS)

    Bennett, C.

    1978-01-01

    Characteristic data, primarily on high rate lithium sulfur dioxide design (basically in the D and DD cell configuration), both before and after much exposure to environmental conditions are discussed. The environmental as opposed to signle cells. Discussion was generated among the Workshop participants and comments and questions are reported. Graphical representations of the test data are presented.

  15. Lithium in the Kidney: Friend and Foe?

    PubMed

    Alsady, Mohammad; Baumgarten, Ruben; Deen, Peter M T; de Groot, Theun

    2016-06-01

    Trace amounts of lithium are essential for our physical and mental health, and administration of lithium has improved the quality of life of millions of patients with bipolar disorder for >60 years. However, in a substantial number of patients with bipolar disorder, long-term lithium therapy comes at the cost of severe renal side effects, including nephrogenic diabetes insipidus and rarely, ESRD. Although the mechanisms underlying the lithium-induced renal pathologies are becoming clearer, several recent animal studies revealed that short-term administration of lower amounts of lithium prevents different forms of experimental AKI. In this review, we discuss the knowledge of the pathologic and therapeutic effects of lithium in the kidney. Furthermore, we discuss the underlying mechanisms of these seemingly paradoxical effects of lithium, in which fine-tuned regulation of glycogen synthase kinase type 3, a prime target for lithium, seems to be key. The new discoveries regarding the protective effect of lithium against AKI in rodents call for follow-up studies in humans and suggest that long-term therapy with low lithium concentrations could be beneficial in CKD. PMID:26577775

  16. Lithium cell technology and safety report of the Tri-Service Lithium Safety Committee

    NASA Technical Reports Server (NTRS)

    Reiss, E.

    1980-01-01

    The organization of the Tri-Service Lithium Safety Committee is described. The following areas concerning lithium batteries are discussed: transportation--DOT Exemption 7052, FAA; disposal; storage; individual testing/test results; and battery design and usage.

  17. Lithium ferrate and lithium cobaltate cathodes for molten carbonate fuel cells

    SciTech Connect

    Krumpelt, M.; Roche, M.; Bloom, I.; Indacochea, J.E.; Kucera, G.

    1994-08-01

    The objective of this research is to develop cathodes for the molten carbonate fuel cells (MCFC) having a performance approaching that of the lithiated nickel oxide cathode and a significantly greater life, particularly in pressurized MCFCs. To meet this objective, cathodes containing either doubly doped lithium ferrate or lithium cobaltate are being developed. In this project, the authors are optimizing the composition, microstructure, and loading density of the doubly doped lithium ferrate cathode and the lithium cobaltate cathodes.

  18. Measuring nanocurie quantities of tritium bred in metallic lithium and lithium oxide samples

    SciTech Connect

    Bertone, P.C.

    1985-07-01

    The LBM program requires that nanocurie quantities of tritium, bred in both lithium oxide pellets and lithium samples, be measured with an uncertainty not exceeding + or - 6%. Two methods of accurately measuring nanocurie quantities of tritium bred in LBM lithium oxide pellets and one method of accurately measuring nanocurie quantities of tritium bred in lithium samples are described. Potential errors associated with these tritium measurement techniques are also discussed.

  19. Lithium borate cluster salts as novel redox shuttles for overcharge protection of lithium-ion cells.

    SciTech Connect

    Chen, Z.; Liu, J.; Jansen, A. N.; Casteel, B.; Amine, K.; GirishKumar, G.; Air Products and Chemicals, Inc.

    2010-01-01

    Redox shuttle is a promising mechanism for intrinsic overcharge protection in lithium-ion cells and batteries. Two lithium borate cluster salts are reported to function as both the main salt for a nonaqueous electrolyte and the redox shuttle for overcharge protection. Lithium borate cluster salts with a tunable redox potential are promising candidates for overcharge protection for most positive electrodes in state-of-the-art lithium-ion cells.

  20. Lithium anomaly near Pringle, southern Black Hills, South Dakota, possibly caused by unexposed rare-mineral pegmatite

    SciTech Connect

    Norton, J.J.

    1984-01-01

    Six samples of biotite schist from a site near Pringle, South Dakota, contained from 140 to 750 parts per million lithium. These values are far greater than are found in mica schists in most of the rest of the southern Black Hills. The lithium may have emanated from concealed lithium pegmatite, and such pegmatite can be of interest as a possible source of rare minerals, especially tantalite and beryl. Whether making a full test of the anomaly will become economically judicious is much less clear. 18 refs., 2 figs., 2 tabs.

  1. Lithium anomaly near Pringle, southern Black Hills, South Dakota, possibly caused by unexposed rare-mineral pegmatite

    USGS Publications Warehouse

    Norton, James Jennings

    1984-01-01

    Six samples of biotite schist from a site near Pringle, South Dakota, contained from 140 to 750 parts per million lithium. These values are far greater than are found in mica schists in most of the rest of the southern Black Hills. The lithium may have emanated from concealed lithium pegmatite, and such pegmatite can be of interest as a possible source of rare minerals, especially tantalite and beryl. Whether making a full test of the anomaly will become economically judicious is much less clear.

  2. Lithium: Sources, Production, Uses, and Recovery Outlook

    NASA Astrophysics Data System (ADS)

    Talens Peiró, Laura; Villalba Méndez, Gara; Ayres, Robert U.

    2013-08-01

    The demand for lithium has increased significantly during the last decade as it has become key for the development of industrial products, especially batteries for electronic devices and electric vehicles. This article reviews sources, extraction and production, uses, and recovery and recycling, all of which are important aspects when evaluating lithium as a key resource. First, it describes the estimated reserves and lithium production from brine and pegmatites, including the material and energy requirements. Then, it continues with a description about the current uses of lithium focusing on its application in batteries and concludes with a description of the opportunities for recovery and recycling and the future demand forecast. The article concludes that the demand of lithium for electronic vehicles will increase from 30% to almost 60% by 2020. Thus, in the next years, the recovery and recycling of lithium from batteries is decisive to ensure the long-term viability of the metal.

  3. Lithium-aluminum-iron electrode composition

    DOEpatents

    Kaun, Thomas D.

    1979-01-01

    A negative electrode composition is presented for use in a secondary electrochemical cell. The cell also includes an electrolyte with lithium ions such as a molten salt of alkali metal halides or alkaline earth metal halides that can be used in high-temperature cells. The cell's positive electrode contains a a chalcogen or a metal chalcogenide as the active electrode material. The negative electrode composition includes up to 50 atom percent lithium as the active electrode constituent in an alloy of aluminum-iron. Various binary and ternary intermetallic phases of lithium, aluminum and iron are formed. The lithium within the intermetallic phase of Al.sub.5 Fe.sub.2 exhibits increased activity over that of lithium within a lithium-aluminum alloy to provide an increased cell potential of up to about 0.25 volt.

  4. Using lithium as a neuroprotective agent in patients with cancer.

    PubMed

    Khasraw, Mustafa; Ashley, David; Wheeler, Greg; Berk, Michael

    2012-01-01

    Neurocognitive impairment is being increasingly recognized as an important issue in patients with cancer who develop cognitive difficulties either as part of direct or indirect involvement of the nervous system or as a consequence of either chemotherapy-related or radiotherapy-related complications. Brain radiotherapy in particular can lead to significant cognitive defects. Neurocognitive decline adversely affects quality of life, meaningful employment, and even simple daily activities. Neuroprotection may be a viable and realistic goal in preventing neurocognitive sequelae in these patients, especially in the setting of cranial irradiation. Lithium is an agent that has been in use for psychiatric disorders for decades, but recently there has been emerging evidence that it can have a neuroprotective effect.This review discusses neurocognitive impairment in patients with cancer and the potential for investigating the use of lithium as a neuroprotectant in such patients. PMID:23121766

  5. Flupenthixol decanoate in recurrent manic-depressive illness. A comparison with lithium.

    PubMed

    Ahlfors, U G; Baastrup, P C; Dencker, S J; Elgen, K; Lingjaerde, O; Pedersen, V; Schou, M; Aaskoven, O

    1981-09-01

    The hypothesis that flupenthixol decanoate may serve as an alternative to prophylactically administered lithium in recurrent manic-depressive illness, bipolar and unipolar type, was tested in two groups of patients. In Group I the patients were allocated randomly to maintenance treatment with either lithium or flupenthixol decanoate. The patients in Group II had previously been given lithium and were switched to flupenthixol decanoate because of unsatisfactory prophylactic effect of lithium, doubtful tablet compliance, troublesome side effects, or fear of later harmful effects. The flupenthixol decanoate dosage was 20 mg every 2-3 weeks. The study was not blind. In Group I neither lithium treatment (14 patients) nor treatment with flupenthixol decanoate (19 patients) led to a significant fall of mean episode frequency or mean per cent time ill. The reasons for this lack of response are not clear, but prognostically negative selection of the patients presumably took place before and possibly also during the hospitalization. Since absent effects cannot be compared, this part of the trial remains inconclusive. In Group II (93 patients) treatment with flupenthixol decanoate was associated with significant falls of the frequency of manic episodes and per cent time ill in mania and with significant rises of the frequency of depressive episodes and per cent time ill in depression. Increase of depressive morbidity was seen only in patients who had been given lithium during the pre-trial period and was presumably a result of the discontinuation of lithium. It is not known whether flupenthixol decanoate is of value in the prophylactic treatment of recurrent manic-depressive illness, but the drug may be worth trying in patients whose disease is dominated more by manic than by depressive recurrences and who do not respond to lithium or do not tolerate it or do not take it. PMID:7324992

  6. Lithium metal oxide electrodes for lithium cells and batteries

    DOEpatents

    Thackeray, Michael M.; Johnson, Christopher S.; Amine, Khalil

    2008-12-23

    A lithium metal oxide positive electrode for a non-aqueous lithium cell is disclosed. The cell is prepared in its initial discharged state and has a general formula xLiMO.sub.2.(1-x)Li.sub.2M'O.sub.3 in which 0

  7. Lithium Metal Oxide Electrodes For Lithium Cells And Batteries

    DOEpatents

    Thackeray, Michael M.; Johnson, Christopher S.; Amine, Khalil; Kim, Jaekook

    2004-01-20

    A lithium metal oxide positive electrode for a non-aqueous lithium cell is disclosed. The cell is prepared in its initial discharged state and has a general formula xLiMO.sub.2.(1-x)Li.sub.2 M'O.sub.3 in which 0

  8. Improving electrolytes for lithium-ion and lithium oxygen

    NASA Astrophysics Data System (ADS)

    Chalasani, Dinesh

    There is an ever increasing demand for fossil fuels. Lithium ion batteries (LIBs) can effectively reduce the production of greenhouse gases and lessen the need for fossil fuels. LIBs also have great potential in electric vehicle applications as an alternative to petroleum modes of transportation. Understanding the chemical reactions between the electrolyte and electrodes in LIBs is very crucial in developing batteries which can work over a wide temperature range and also give a wide potential window. The Solid Electrolyte Interface (SEI), formed by the reduction of solvent molecules on the surface of electrodes, is an important component of LIBs. The SEI is very essential to the performance of LIBs. One electron reduction pathway products of solvent molecules was investigated using lithium-naphthalenide. Methylene ethylene carbonate, a high temperature additive has been synthesized and its performance has been tested at 60°C. Lithium-Oxygen batteries have an energy density ten times greater than that of LIBs. However, lithium-oxygen batteries have rechargability problems associated with them. The most common electrolyte used in this type of batteries is LiPF6 in carbonate or ether based solvents. LiPF6 inherently decreases electrolyte stability, since LiPF 6 can undergo thermal dissociation into PF5 and LiF. PF 5 being a strong Lewis acid, can react with electron rich species. The thermal decomposition reactions of LiPF6 based electrolytes are studied in detail with regard to LIBs. The comprehensive study has been conducted on the thermal degradation of several electrolyte systems in the presence of Li2O2.

  9. Electrode materials and lithium battery systems

    DOEpatents

    Amine, Khalil; Belharouak, Ilias; Liu, Jun

    2011-06-28

    A material comprising a lithium titanate comprising a plurality of primary particles and secondary particles, wherein the average primary particle size is about 1 nm to about 500 nm and the average secondary particle size is about 1 .mu.m to about 4 .mu.m. In some embodiments the lithium titanate is carbon-coated. Also provided are methods of preparing lithium titanates, and devices using such materials.

  10. Lithium-Ion Cell Storage Study

    NASA Technical Reports Server (NTRS)

    Lee, Leonine; Rao, Gopalkrishna M.

    2000-01-01

    This viewgraph presentation reviews the issues concerning storage of lithium ion batteries. The presentation outlines tests used to establish a best long term storage for the lithium ion cells. Another objective of the study was to determine the preferred solstice condition for the lithium ion chemistry (polymer and liquid electrolyte). It also compared voltage clamped with trickle charge storage. The tests and results are reviewed

  11. Lithium-sulfur hexafluoride magnetohydrodynamic power system

    SciTech Connect

    Dobran, F.

    1987-02-24

    A method is described to operate a two-phase flow magnetohydrodynamic electric power generation system with liquid lithium and gaseous sulfur-hexafluoride flowing through a diverging channel, with side electrodes to remove the electric current generated in the flowing liquid lithium, across the applied magnetic field that is perpendicular to both the flow velocity and electrodes. Sulfur-hexafluoride is dispersed in the form of small bubbles and reacts with liquid lithium that forms a continuous phase to conduct the current between the electrodes so as to produce a near isothermal two-phase flow mixture and provides for an expansion of lithium across the magnetic field in the generator.

  12. Ternary compound electrode for lithium cells

    DOEpatents

    Raistrick, Ian D.; Godshall, Ned A.; Huggins, Robert A.

    1982-01-01

    Lithium-based cells are promising for applications such as electric vehicles and load-leveling for power plants since lithium is very electropositive and of light weight. One type of lithium-based cell utilizes a molten salt electrolyte and normally is operated in the temperature range of about 350.degree.-500.degree. C. Such high temperature operation accelerates corrosion problems. The present invention provides an electrochemical cell in which lithium is the electroactive species. The cell has a positive electrode which includes a ternary compound generally represented as Li-M-O, wherein M is a transition metal. Corrosion of the inventive cell is considerably reduced.

  13. Ternary compound electrode for lithium cells

    DOEpatents

    Raistrick, I.D.; Godshall, N.A.; Huggins, R.A.

    1980-07-30

    Lithium-based cells are promising for applications such as electric vehicles and load-leveling for power plants since lithium is very electropositive and of light weight. One type of lithium-based cell utilizes a molten salt electrolyte and normally is operated in the temperature range of about 350 to 500/sup 0/C. Such high temperature operation accelerates corrosion problems. The present invention provides an electrochemical cell in which lithium is the electroactive species. The cell has a positive electrode which includes a ternary compound generally represented as Li-M-O, wherein M is a transition metal. Corrosion of the inventive cell is considerably reduced.

  14. Secondary lithium cells for space applications

    NASA Technical Reports Server (NTRS)

    Surampudi, S.; Shen, D. H.; Huang, C.-K.; Narayanan, S. R.; Attia, A.; Halpert, G.

    1992-01-01

    It is concluded that secondary lithium batteries are suitable for planetary missions requiring high specific energy, long active shelf life, and limited cycle life. Titanium disulfide cathode material meet all the requirements for rechargeable lithium cell, including high intrinsic reversibility and realizable specific energy. Secondary lithium technology is still evolving, although low capacity cells have been demonstrated and greater than 700 cycle life was achieved. Work is in progress to improve the cycle life and safety of the electrolytes, alternate lithium anode, and the separators.

  15. Lithium Metal Anodes for Rechargeable Batteries

    SciTech Connect

    Xu, Wu; Wang, Jiulin; Ding, Fei; Chen, Xilin; Nasybulin, Eduard N.; Zhang, Yaohui; Zhang, Jiguang

    2013-10-29

    Rechargeable lithium metal batteries have much higher energy density than those of lithium ion batteries using graphite anode. Unfortunately, uncontrollable dendritic lithium growth inherent in these batteries (upon repeated charge/discharge cycling) and limited Coulombic efficiency during lithium deposition/striping has prevented their practical application over the past 40 years. With the emerging of post Li-ion batteries, safe and efficient operation of lithium metal anode has become an enabling technology which may determine the fate of several promising candidates for the next generation of energy storage systems, including rechargeable Li-air battery, Li-S battery, and Li metal battery which utilize lithium intercalation compounds as cathode. In this work, various factors which affect the morphology and Coulombic efficiency of lithium anode will be analyzed. Technologies used to characterize the morphology of lithium deposition and the results obtained by modeling of lithium dendrite growth will also be reviewed. At last, recent development in this filed and urgent need in this field will also be discussed.

  16. Lithium in Medicine: Mechanisms of Action.

    PubMed

    Mota de Freitas, Duarte; Leverson, Brian D; Goossens, Jesse L

    2016-01-01

    In this chapter, we review the mechanism of action of lithium salts from a chemical perspective. A description on how lithium salts are used to treat mental illnesses, in particular bipolar disorder, and other disease states is provided. Emphasis is not placed on the genetics and the psychopharmacology of the ailments for which lithium salts have proven to be beneficial. Rather we highlight the application of chemical methodologies for the characterization of the cellular targets of lithium salts and their distribution in tissues. PMID:26860311

  17. Review of lithium-ion technology

    SciTech Connect

    Levy, S.C.; Cieslak, W.R.

    1993-12-31

    The first practical use of graphite intercalation compounds (GIC) as battery anodes was reported in a 1981 patent by Basu in which a molten salt cell was described having a negative electrode that consisted of lithium intercalated in graphite. A second patent by Basu, issued in 1983, described an ambient temperature rechargeable system which also utilized lithium intercalated in graphite as the anode. Work in this area progressed at a low level, however, until interest was sparked in 1990 when Sony Corporation announced a new ``lithium-ion`` rechargeable cell containing a lithium ion intercalating carbon anode. These cells have the advantages of metallic lithium systems; i.e., high energy density, high voltage, and light weight, without the disadvantages of dendrite formation on charge and the safety considerations associated with metallic lithium. Materials other than carbon have been studied as intercalation anodes. Examples are Fe{sub 2}O{sub 3}, WO{sub 2} and TiS{sub 2}. Although these alternate anode materials are of interest academically and for specialty applications, they do not hold much promise for widespread general use due to their increased weight and lower cell voltage. Studies of cathode materials for lithium-ion systems have centered on the transition metal chalcogenides. A number of these materials are capable of reversibly intercalating lithium ions at a useful potential versus lithium. Both organic liquids and polymers are candidate electrolytes for this technology.

  18. Lithium-Air Cell Development

    NASA Technical Reports Server (NTRS)

    Reid, Concha M.; Dobley, Arthur; Seymour, Frasier W.

    2014-01-01

    Lithium-air (Li-air) primary batteries have a theoretical specific capacity of 11,400 Wh/kg, the highest of any common metal-air system. NASA is developing Li-air technology for a Mobile Oxygen Concentrator for Spacecraft Emergencies, an application which requires an extremely lightweight primary battery that can discharge over 24 hours continuously. Several vendors were funded through the NASA SBIR program to develop Li-air technology to fulfill the requirements of this application. New catalysts and carbon cathode structures were developed to enhance the oxygen reduction reaction and increase surface area to improve cell performance. Techniques to stabilize the lithium metal anode surface were explored. Experimental results for prototype laboratory cells are given. Projections are made for the performance of hypothetical cells constructed from the materials that were developed.

  19. Growth energizes lithium ion interest

    SciTech Connect

    D`Amico, E.

    1996-03-20

    The prospects for big growth in the US for lithium ion batteries (LIBs) has sparked the interest of potential domestic suppliers. {open_quotes}The money that can be made in this market is staggering,{close_quotes} says one industry expert. {open_quotes}Everybody who is remotely related to this industry is interested.{close_quotes} The size of the market, still in its infancy, is difficult to gauge, say consultants, who estimate that leading Japanese producers are each making millions of lithium ion cells/month. {open_quotes}The market is not too measurable right now because the only production is really limited to prototypes being sampled,{close_quotes} says Ward Seitz, a consultant with SRI International (Menlo Park, CA), {open_quotes}but there is phenomenal interest.{close_quotes}

  20. Electrolytes for lithium ion batteries

    SciTech Connect

    Vaughey, John; Jansen, Andrew N.; Dees, Dennis W.

    2014-08-05

    A family of electrolytes for use in a lithium ion battery. The genus of electrolytes includes ketone-based solvents, such as, 2,4-dimethyl-3-pentanone; 3,3-dimethyl 2-butanone(pinacolone) and 2-butanone. These solvents can be used in combination with non-Lewis Acid salts, such as Li.sub.2[B.sub.12F.sub.12] and LiBOB.

  1. Solid polymer electrolyte lithium batteries

    DOEpatents

    Alamgir, Mohamed; Abraham, Kuzhikalail M.

    1993-01-01

    This invention pertains to Lithium batteries using Li ion (Li.sup.+) conductive solid polymer electrolytes composed of solvates of Li salts immobilized in a solid organic polymer matrix. In particular, this invention relates to Li batteries using solid polymer electrolytes derived by immobilizing solvates formed between a Li salt and an aprotic organic solvent (or mixture of such solvents) in poly(vinyl chloride).

  2. Solid polymer electrolyte lithium batteries

    DOEpatents

    Alamgir, M.; Abraham, K.M.

    1993-10-12

    This invention pertains to Lithium batteries using Li ion (Li[sup +]) conductive solid polymer electrolytes composed of solvates of Li salts immobilized in a solid organic polymer matrix. In particular, this invention relates to Li batteries using solid polymer electrolytes derived by immobilizing solvates formed between a Li salt and an aprotic organic solvent (or mixture of such solvents) in poly(vinyl chloride). 3 figures.

  3. Crystallization of lithium borate glasses

    NASA Technical Reports Server (NTRS)

    Goktas, A. A.; Neilson, G. F.; Weinberg, M. C.

    1992-01-01

    The glass-forming ability and crystallization behavior of lithium borate compositions, in the diborate-to-metaborate-range, were studied. In particular, the nature and sequence of formation of crystalline phases and the tendency toward devitrification were investigated as functions of temperature, thermal history and batch composition. It was found that the sequence of crystalline phase formation was sensitive to all of the three latter factors, and it was observed that under certain conditions metastable defect structures of the metaborate can appear.

  4. Aluminum-lithium target behavior

    SciTech Connect

    McDonell, W.R.

    1989-10-01

    Information on physical properties and irradiation behavior of aluminum-lithium target alloys employed for the production of tritium in Savannah River reactors has been reviewed to support development of technology for the New Production Reactor (NPR). Phase compositions and microstructures, thermal conductivity, mechanical properties, and constituent diffusion phenomena of the alloys, established in prior site studies, are presented. Irradiation behavior, including distributions of product tritium and helium and related exposure limits due to swelling and cracking of the target alloys is discussed, along with gas release processes occurring during subsequent product recovery operations. The property review supports designation of the aluminum-lithium alloys as ideally well-suited target materials for low-temperature, tritium-producing reactors, demonstrated over 35 years of Savannah River reactor operation. Low temperature irradiation and reaction with lithium in the alloy promotes tritium retention during reactor exposure, and the aluminum provides a matrix from which the product is readily recovered on heating following irradiation. 33 refs., 26 figs., 8 tabs.

  5. Lithium batteries for pulse power

    SciTech Connect

    Redey, L.

    1990-01-01

    New designs of lithium batteries having bipolar construction and thin cell components possess the very low impedance that is necessary to deliver high-intensity current pulses. The R D and understanding of the fundamental properties of these pulse batteries have reached an advanced level. Ranges of 50--300 kW/kg specific power and 80--130 Wh/kg specific energy have been demonstrated with experimental high-temperature lithium alloy/transition-metal disulfide rechargeable bipolar batteries in repeated 1- to 100-ms long pulses. Other versions are designed for repetitive power bursts that may last up to 20 or 30 s and yet may attain high specific power (1--10 kW/kg). Primary high-temperature Li-alloy/FeS{sub 2} pulse batteries (thermal batteries) are already commercially available. Other high-temperature lithium systems may use chlorine or metal-oxide positive electrodes. Also under development are low-temperature pulse batteries: a 50-kW Li/SOCl{sub 2} primary batter and an all solid-state, polymer-electrolyte secondary battery. Such pulse batteries could find use in commercial and military applications in the near future. 21 refs., 8 figs.

  6. Nickel-Hydrogen and Lithium Ion Space Batteries

    NASA Technical Reports Server (NTRS)

    Reid, Robert O., II

    2004-01-01

    The tasks of the Electrochemistry Branch of NASA Glenn Research Center are to improve and develop high energy density and rechargeable, life-long batteries. It is with these batteries that people across the globe are able to power their cell phones, laptop computers, and cameras. Here, at NASA Glenn Research Center, the engineers and scientists of the Electrochemistry branch are leading the way in the development of more powerful, long life batteries that can be used to power space shuttles and satellites. As of now, the cutting edge research and development is being done on nickel-hydrogen batteries and lithium ion batteries. Presently, nickel-hydrogen batteries are common types of batteries that are used to power satellites, space stations, and space shuttles, while lithium batteries are mainly used to power smaller appliances such as portable computers and phones. However, the Electrochemistry Branch at NASA Glenn Research Center is focusing more on the development of lithium ion batteries for deep space use. Because of the limitless possibilities, lithium ion batteries can revolutionize the space industry for the better. When compared to nickel-hydrogen batteries, lithium ion batteries possess more advantages than its counterpart. Lithium ion batteries are much smaller than nickel-hydrogen batteries and also put out more power. They are more energy efficient and operate with much more power at a reduced weight than its counterpart. Lithium ion cells are also cheaper to make, possess flexibility that allow for different design modifications. With those statistics in hand, the Electrochemistry Branch of NASA Glenn has decided to shut down its Nickel-Hydrogen testing for lithium ion battery development. Also, the blackout in the summer of 2003 eliminated vital test data, which played a part in shutting down the program. from the nickel-hydrogen batteries and compare it to past data. My other responsibilities include superheating the electrolyte that is used in the

  7. Lithium-bearing rocks of the Horse Spring Formation, Clark County, Nevada

    USGS Publications Warehouse

    Brenner-Tourtelot, E. F.; Glanzman, R.K.

    1978-01-01

    The Horse Spring Formation of Miocene age in Clark County, Nevada, contains as much as 0.5% Li in individual samples. Rock sequences which average 0.1% Li range from 3 m thick near Gold Butte (south of Mesquite, Nev.) to as much as 40 m thick near Lava Butte (east of Las Vegas, Nev.) about 75 km to the west. The lithium-bearing beds are light colored to white and contain hectorite in a dolomite, magnesite, or calcite matrix. Varied amounts of gypsum, halite, celestite, clinoptilolite, quartz, feldspar, biolite and colemanite are also present locally. Hectorite is the only lithium mineral recognized to date. The lithium-rich rocks contain low concentrations of most other minor elements except that boron and strontium are enriched. Rarely, barium, arsenic, and zinc are present in anomalously large amounts. The lithium-enriched part of the Horse Spring Formation was formed from a series of volcanic ashes which were deposited in a playa. Relict volcanic ash is recognizable in thin sections as remnant glass shards and vitroclastic textures. Most of the original glass has been altered to clay minerals, carbonate minerals, or zeolites, presumably through interaction with highly saline pore waters. Abundant evidence of spring activity suggests that thermal waters played a part in releasing the lithium from volcanic materials. ?? 1978.

  8. Dependence of Recycling and Edge Profiles on Lithium Evaporation in High Triangularity, High Performance NSTX H-mode Discharges

    SciTech Connect

    Maingi, R; Osborne, T H; Bell, M G; Bell, R E; Boyle, D P; Canik, J M; Dialla, A; Kaita, R; Kaye, S M; Kugel, H W; LeBlanc, B P; Sabbagh, S A; Skinner, C H; Soukhanovskii, V A

    2014-04-01

    In this paper, the effects of a pre-discharge lithium evaporation scan on highly shaped discharges in the National Spherical Torus Experiment (NSTX) are documented. Lithium wall conditioning ('dose') was routinely applied onto graphite plasma facing components between discharges in NSTX, partly to reduce recycling. Reduced D[sub]α emission from the lower and upper divertor and center stack was observed, as well as reduced midplane neutral pressure; the magnitude of reduction increased with the pre-discharge lithium dose. Improved energy confinement, both raw τ[sub]E and H-factor normalized to scalings, with increasing lithium dose was also observed. At the highest doses, we also observed elimination of edge-localized modes. The midplane edge plasma profiles were dramatically altered, comparable to lithium dose scans at lower shaping, where the strike point was farther from the lithium deposition centroid. This indicates that the benefits of lithium conditioning should apply to the highly shaped plasmas planned in NSTX-U.

  9. Dependence of recycling and edge profiles on lithium evaporation in high triangularity, high performance NSTX H-mode discharges.

    SciTech Connect

    Maingi, R.; Osborne, T. H.; Bell, M. G.; Bell, R. E.; Boyle, D. P.; Canik, J. M.; Diallo, A.; Kaita, R.; Kaye, S. M.; Kugel, H. W.; LeBlanc, B. P.; Sabbagh, S. A.; Skinner, C. H.; Soukhanovskii, V. A.

    2014-11-04

    In this paper, the effects of a pre-discharge lithium evaporation variation on highly shaped discharges in the National Spherical Torus Experiment (NSTX) are documented. Lithium wall conditioning (‘dose’) was routinely applied onto graphite plasma facing components between discharges in NSTX, partly to reduce recycling. Reduced Dα emission from the lower and upper divertor and center stack was observed, as well as reduced midplane neutral pressure; the magnitude of reduction increased with the pre-discharge lithium dose. Improved energy confinement, both raw τE and H-factor normalized to scalings, with increasing lithium dose was also observed. At the highest doses, we also observed elimination of edge-localized modes. The midplane edge plasma profiles were dramatically altered, comparable to lithium dose scans at lower shaping, where the strike point was farther from the lithium deposition centroid. As a result, this indicates that the benefits of lithium conditioning should apply to the highly shaped plasmas planned in NSTX-U.

  10. Dependence of recycling and edge profiles on lithium evaporation in high triangularity, high performance NSTX H-mode discharges.

    DOE PAGESBeta

    Maingi, R.; Osborne, T. H.; Bell, M. G.; Bell, R. E.; Boyle, D. P.; Canik, J. M.; Diallo, A.; Kaita, R.; Kaye, S. M.; Kugel, H. W.; et al

    2014-11-04

    In this paper, the effects of a pre-discharge lithium evaporation variation on highly shaped discharges in the National Spherical Torus Experiment (NSTX) are documented. Lithium wall conditioning (‘dose’) was routinely applied onto graphite plasma facing components between discharges in NSTX, partly to reduce recycling. Reduced Dα emission from the lower and upper divertor and center stack was observed, as well as reduced midplane neutral pressure; the magnitude of reduction increased with the pre-discharge lithium dose. Improved energy confinement, both raw τE and H-factor normalized to scalings, with increasing lithium dose was also observed. At the highest doses, we also observedmore » elimination of edge-localized modes. The midplane edge plasma profiles were dramatically altered, comparable to lithium dose scans at lower shaping, where the strike point was farther from the lithium deposition centroid. As a result, this indicates that the benefits of lithium conditioning should apply to the highly shaped plasmas planned in NSTX-U.« less

  11. Lithium barium titanate: A stable lithium storage material for lithium-ion batteries

    NASA Astrophysics Data System (ADS)

    Lin, Xiaoting; Li, Peng; Shao, Lianyi; Shui, Miao; Wang, Dongjie; Long, Nengbing; Ren, Yuanlong; Shu, Jie

    2015-03-01

    A series of Li2BaTi6O14 samples are synthesized by a traditional solid-state method by calcining at different temperatures from 800 to 1000 °C. Structural analysis and electrochemical evaluation suggest that the optimum calcining temperature for Li2BaTi6O14 is 950 °C. The Li2BaTi6O14 calcined at 950 °C exhibits a high purity phase with an excellent reversible capacity of 145.7 mAh g-1 for the first cycle at a current density of 50 mA g-1. After 50 cycles, the reversible capacity can be maintained at 137.7 mAh g-1, with the capacity retention of 94.51%. Moreover, this sample also shows outstanding rate property with a high reversible capacity of 118 mAh g-1 at 300 mA g-1. The excellent electrochemical performance is attributed to the stable lithium storage host structure, decreased electrochemical resistance and improved lithium-ion diffusion coefficient. In-situ and ex-situ structure analysis shows that the electrochemical reaction of Li2BaTi6O14 with Li is a highly reversible lithiation-delithiation process. Therefore, Li2BaTi6O14 may be a promising alternative anode material for lithium-ion batteries.

  12. Dissecting anode swelling in commercial lithium-ion batteries

    NASA Astrophysics Data System (ADS)

    Zhang, Ningxin; Tang, Huaqiong

    2012-11-01

    An innovative method is applied to investigate anode swelling during electrochemical processes in commercial lithium-ion batteries. Cathode surface is partially covered with a piece of paste to block the transportation of lithium ion from active material during charging/discharging, and the corresponding part on the anode film shows no formation of Li-graphite compounds during different electrochemical processes, which is confirmed by XRD analysis. The increases of anode thickness within and outside lithiated zone are measured, and defined as electrochemical swelling and physical swelling respectively. The microscopic lattice expansion of graphite due to lithiation process correlates to mesoscopic electrochemical swelling synchronically, while physical swelling tends to decrease steadily with time. The relationship among the microscopic stress due to lithium-ion intercalation, the mesoscopic stress resulting in anode swelling, and the macroscopic rippling of pouch cell after a large number of cycle test, is analyzed and correlated in terms of stress evolution across different scales, and suggestions for solving anode swelling are provided.

  13. Lithium-mediated protection against ethanol neurotoxicity.

    PubMed

    Luo, Jia

    2010-01-01

    Lithium has long been used as a mood stabilizer in the treatment of manic-depressive (bipolar) disorder. Recent studies suggest that lithium has neuroprotective properties and may be useful in the treatment of acute brain injuries such as ischemia and chronic neurodegenerative diseases such as Alzheimer's disease, Parkinson's disease, Huntington's disease and amyotrophic lateral sclerosis. One of the most important neuroprotective properties of lithium is its anti-apoptotic action. Ethanol is a neuroteratogen and fetal alcohol spectrum disorders (FASD) are caused by maternal ethanol exposure during pregnancy. FASD is the leading cause of mental retardation. Ethanol exposure causes neuroapoptosis in the developing brain. Ethanol-induced loss of neurons in the central nervous system underlies many of the behavioral deficits observed in FASD. Excessive alcohol consumption is also associated with Wernicke-Korsakoff syndrome and neurodegeneration in the adult brain. Recent in vivo and in vitro studies indicate that lithium is able to ameliorate ethanol-induced neuroapoptosis. Lithium is an inhibitor of glycogen synthase kinase 3 (GSK3) which has recently been identified as a mediator of ethanol neurotoxicity. Lithium's neuroprotection may be mediated by its inhibition of GSK3. In addition, lithium also affects many other signaling proteins and pathways that regulate neuronal survival and differentiation. This review discusses the recent evidence of lithium-mediated protection against ethanol neurotoxicity and potential underlying mechanisms. PMID:20661453

  14. Jeff Chamberlain on Lithium-air batteries

    SciTech Connect

    Chamberlain, Jeff

    2009-01-01

    Jeff Chamberlain, technology transfer expert at Argonne National Laboratory, speaks on the new technology Lithium-air batteries, which could potentially increase energy density by 5-10 times over lithium-ion batteries. More information at http://www.anl.gov/Media_Center/News/2009/batteries090915.html

  15. Convective Stirring in Liquid Lithium (LTX)

    NASA Astrophysics Data System (ADS)

    Cassin, Margaret; Kearns, Eugene; Majeski, Richard

    2011-10-01

    LTX is a spherical tokamak with R=0.4 m, a=0.26 m, and elongation=1.5. LTX has a heated (300 - 400 C) liner, designed to be coated with lithium. During experiments in 2010, oxidation of the lithium surface was observed when the liner was heated to 300 C, above the melting point of lithium (182 C). A pumping system is being installed to absorb and pump background gasses which react with lithium, similar to a getter pump, using liquid and solid lithium. Lithium will be loaded into a yttria crucible heated from below by a small, HeatWave model TB175 300W cartridge heater to produce convective currents in order to maintain a clean lithium surface and decrease the time for oxide formation. This system was tested in an argon glove box using a copper heat concentrator - instead of the HeatWave vacuum-compatible unit. Infrared thermometry and thermocouples were used to monitor the surface temperature of the molten lithium, and convective flow patterns. A 200 FPS high speed camera was also employed to monitor flows, using the motion of residual oxide patches. Results from the measurements will be presented. Supported by US DOE contract DE-AC02-09CH11466.

  16. Neuroleptic malignant syndrome and lithium carbonate.

    PubMed Central

    Fava, S; Galizia, A C

    1995-01-01

    The authors describe a case of neuroleptic malignant syndrome that occurred in a patient on amitriptyline and lithium carbonate. They suggest that lithium-antidepressant combination can precipitate this syndrome. Intestinal pseudo-obstruction was a prominent feature in the patient in this study. PMID:7647084

  17. Lithium Ion Battery Design and Safety

    NASA Technical Reports Server (NTRS)

    Au, George; Locke, Laura

    2001-01-01

    This viewgraph presentation makes several recommendations to ensure the safe and effective design of Lithium ion cell batteries. Large lithium ion cells require pressure switches and small cells require pressure disconnects and other safety devices with the ability to instantly interrupt flow. Other suggestions include specifications for batteries and battery chargers.

  18. Anode for rechargeable ambient temperature lithium cells

    NASA Technical Reports Server (NTRS)

    Huang, Chen-Kuo (Inventor); Surampudi, Subbarao (Inventor); Attia, Alan I. (Inventor); Halpert, Gerald (Inventor)

    1994-01-01

    An ambient room temperature, high density, rechargeable lithium battery includes a Li(x)Mg2Si negative anode which intercalates lithium to form a single crystalline phase when x is up to 1.0 and an amorphous phase when x is from 1 to 2.0. The electrode has good reversibility and mechanical strength after cycling.

  19. Jeff Chamberlain on Lithium-air batteries

    ScienceCinema

    Chamberlain, Jeff

    2013-04-19

    Jeff Chamberlain, technology transfer expert at Argonne National Laboratory, speaks on the new technology Lithium-air batteries, which could potentially increase energy density by 5-10 times over lithium-ion batteries. More information at http://www.anl.gov/Media_Center/News/2009/batteries090915.html

  20. TREATMENT OF MANIA WITH CARBAMAZEPINE AND LITHIUM

    PubMed Central

    Desai, Nimesh G.; Gangadhar, B.N.; Pradhan, N.; Channabasavanna, S.M.

    1983-01-01

    SUMMARY A young manic patient who showed poor response to lithium, neuroleptics and ECT and developed severe cxtrapyramidal side effects restricting the use of neuroleptics in high doses; showed marked clinical improvement with a combination of carbamazepine and lithium with sustained recovery. The case reported to illustrate the possible synergistic action suggested earlier, encouraging the authors to take up a crossover trial. PMID:21847260

  1. Characterization of prototype secondary lithium battery

    NASA Technical Reports Server (NTRS)

    Somoano, R.

    1980-01-01

    The performance characteristics of ambient temperature secondary lithium batteries were determined through continuous cycle tests with periodic current and voltage measurements. Cycle life of the lithium anode was found to be an important problem area as was the formation of dentrite breakage and subsequent shorting. Energy density was increased by using more efficient cathode structures.

  2. Lithium, a preliminary survey of its mineral occurrence in flint clay and related rock types in the United States

    USGS Publications Warehouse

    Tourtelot, H.A.; Brenner-Tourtelot, E. F.

    1978-01-01

    Maximum concentrations of lithium found in samples of flint clay and associated rocks of Pennsylvanian age in different States, in parts per million (ppm), are: Missouri, 5100; Pennsylvania-Maryland, 2100; Kentucky, 890; Ohio, 660; Alabama, 750; and Illinois, 160. Lithium-bearing kaolin deposits are distributed in the Coastal Plain province from New Jersey to Texas, and one occurs in Idaho; maximum lithium concentrations in samples from these deposits range from 64 to 180 ppm. The maximum concentration found in the Arkansas bauxite region is 460 ppm and that in flint clay in Colorado is 370 ppm. Samples from areas other than Pennsylvania, Maryland, Kentucky and Missouri are relatively few in number, represent mostly commercially valuable clays, and represent only a part of the refractory clay deposits in the United States. Data are not available on the clays associated with these deposits that may be unusable because they contain too much lithium as well as other deleterious elements. In both Pennsylvania and Missouri, lithium contents vary regionally between districts and locally between deposits. In samples containing more than 2000 ppm lithium, the lithium occurs in a dioctahedral chlorite mineral very similar to cookeite, which previously has not been recognized in sedimentary clays. The associated clays consist chiefly of well-crystallized kaolinite. The dioctahedral chlorite, however, seems to be most abundant where diaspore and boehmite occur along with the kaolinite. Barium, chromium, copper, phosphorus and strontium are present in some samples in amounts of several hundred pans per million or more, and may contribute to the failure of some clays to perform satisfactorily in firing tests. Lithium-rich clays could serve as a significant lithium resource in the very distant future. Clays that contain as much as 1% lithium may be common enough in Missouri or in Pennsylvania to be produced as a by-product to help support benefication costs for refractory clays

  3. A lithium-oxygen battery based on lithium superoxide

    NASA Astrophysics Data System (ADS)

    Lu, Jun; Jung Lee, Yun; Luo, Xiangyi; Chun Lau, Kah; Asadi, Mohammad; Wang, Hsien-Hau; Brombosz, Scott; Wen, Jianguo; Zhai, Dengyun; Chen, Zonghai; Miller, Dean J.; Sub Jeong, Yo; Park, Jin-Bum; Zak Fang, Zhigang; Kumar, Bijandra; Salehi-Khojin, Amin; Sun, Yang-Kook; Curtiss, Larry A.; Amine, Khalil

    2016-01-01

    Batteries based on sodium superoxide and on potassium superoxide have recently been reported. However, there have been no reports of a battery based on lithium superoxide (LiO2), despite much research into the lithium-oxygen (Li-O2) battery because of its potential high energy density. Several studies of Li-O2 batteries have found evidence of LiO2 being formed as one component of the discharge product along with lithium peroxide (Li2O2). In addition, theoretical calculations have indicated that some forms of LiO2 may have a long lifetime. These studies also suggest that it might be possible to form LiO2 alone for use in a battery. However, solid LiO2 has been difficult to synthesize in pure form because it is thermodynamically unstable with respect to disproportionation, giving Li2O2 (refs 19, 20). Here we show that crystalline LiO2 can be stabilized in a Li-O2 battery by using a suitable graphene-based cathode. Various characterization techniques reveal no evidence for the presence of Li2O2. A novel templating growth mechanism involving the use of iridium nanoparticles on the cathode surface may be responsible for the growth of crystalline LiO2. Our results demonstrate that the LiO2 formed in the Li-O2 battery is stable enough for the battery to be repeatedly charged and discharged with a very low charge potential (about 3.2 volts). We anticipate that this discovery will lead to methods of synthesizing and stabilizing LiO2, which could open the way to high-energy-density batteries based on LiO2 as well as to other possible uses of this compound, such as oxygen storage.

  4. A lithium-oxygen battery based on lithium superoxide.

    PubMed

    Lu, Jun; Lee, Yun Jung; Luo, Xiangyi; Lau, Kah Chun; Asadi, Mohammad; Wang, Hsien-Hau; Brombosz, Scott; Wen, Jianguo; Zhai, Dengyun; Chen, Zonghai; Miller, Dean J; Jeong, Yo Sub; Park, Jin-Bum; Fang, Zhigang Zak; Kumar, Bijandra; Salehi-Khojin, Amin; Sun, Yang-Kook; Curtiss, Larry A; Amine, Khalil

    2016-01-21

    Batteries based on sodium superoxide and on potassium superoxide have recently been reported. However, there have been no reports of a battery based on lithium superoxide (LiO2), despite much research into the lithium-oxygen (Li-O2) battery because of its potential high energy density. Several studies of Li-O2 batteries have found evidence of LiO2 being formed as one component of the discharge product along with lithium peroxide (Li2O2). In addition, theoretical calculations have indicated that some forms of LiO2 may have a long lifetime. These studies also suggest that it might be possible to form LiO2 alone for use in a battery. However, solid LiO2 has been difficult to synthesize in pure form because it is thermodynamically unstable with respect to disproportionation, giving Li2O2 (refs 19, 20). Here we show that crystalline LiO2 can be stabilized in a Li-O2 battery by using a suitable graphene-based cathode. Various characterization techniques reveal no evidence for the presence of Li2O2. A novel templating growth mechanism involving the use of iridium nanoparticles on the cathode surface may be responsible for the growth of crystalline LiO2. Our results demonstrate that the LiO2 formed in the Li-O2 battery is stable enough for the battery to be repeatedly charged and discharged with a very low charge potential (about 3.2 volts). We anticipate that this discovery will lead to methods of synthesizing and stabilizing LiO2, which could open the way to high-energy-density batteries based on LiO2 as well as to other possible uses of this compound, such as oxygen storage. PMID:26751057

  5. Steady-state pharmacokinetics of lithium carbonate in healthy subjects.

    PubMed Central

    Hunter, R

    1988-01-01

    1. The pharmacokinetics of lithium in six healthy volunteers stabilised on lithium were investigated and appropriate pharmacokinetic parameters calculated. 2. The results illustrate important differences in single and multiple dose lithium pharmacokinetics; the implications for minimising lithium-induced renal damage are discussed. PMID:3129009

  6. 49 CFR 173.185 - Lithium cells and batteries.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ...) includes both lithium metal and lithium ion chemistries. Equipment means the device or apparatus for which... ion cells or batteries packed with the equipment must be packaged in accordance with paragraph (b)(3... 20 Wh for a lithium ion cell or 100 Wh for a lithium ion battery. After December 31, 2015,...

  7. 76 FR 53056 - Outbound International Mailings of Lithium Batteries

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-08-25

    ... requirements established for mailpieces containing equipment with lithium metal or lithium-ion batteries in... exposure of the contents during normal handling in the mail. 135.63 Secondary Lithium-ion (Rechargeable) Cells and Batteries. Small consumer-type lithium-ion cells and batteries like those used to power...

  8. 77 FR 21714 - Hazardous Materials: Transportation of Lithium Batteries

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-04-11

    ... Safety Administration, telephone (202) 366-1074. Background On January 11, 2010 (75 FR 1302), PHMSA, in... Assessment of Bulk-Packed, Rechargeable Lithium-Ion Cells in Transport Category Aircraft; April 2006 (DOT/FAA... configurations of lithium batteries: 1. Lithium ion batteries (PI 965). 2. Lithium ion batteries packed...

  9. Lithium ion batteries based on nanoporous silicon

    DOEpatents

    Tolbert, Sarah H.; Nemanick, Eric J.; Kang, Chris Byung-Hwa

    2015-09-22

    A lithium ion battery that incorporates an anode formed from a Group IV semiconductor material such as porous silicon is disclosed. The battery includes a cathode, and an anode comprising porous silicon. In some embodiments, the anode is present in the form of a nanowire, a film, or a powder, the porous silicon having a pore diameters within the range between 2 nm and 100 nm and an average wall thickness of within the range between 1 nm and 100 nm. The lithium ion battery further includes, in some embodiments, a non-aqueous lithium containing electrolyte. Lithium ion batteries incorporating a porous silicon anode demonstrate have high, stable lithium alloying capacity over many cycles.

  10. Structure of lithium-doped polyacetylene

    NASA Astrophysics Data System (ADS)

    Murthy, N. S.; Shacklette, L. W.; Baughman, R. H.

    1989-12-01

    A trigonal structure with three polymer chains per lithium column is proposed for lithium-doped polyacetylene. A calculation of the x-ray diffraction profile, using the unit-cell dimension and the lithium concentration as the only variables, is in good agreement with the observed data. The proposed structure optimizes the electrostatic interactions by maximizing both the Li+-Li+ separations and the coordination of negatively charged carbons and positively charged lithiums. Unlike the tetragonal lattice found in polyacetylene complexed with larger alkali-metal ions (K+, Rb+, and Cs+), the trigonal structure permits the undoped and the doped phases to coexist without any significant lattice mismatch at the boundary between the two phases. While the chain axis expands by ~1% upon doping with lithium, the projected area per chain remains essentially unchanged.

  11. Chemical feasibility of lithium as a matrix for structural composites

    NASA Technical Reports Server (NTRS)

    Swann, R. T.; Esterling, D. M.

    1984-01-01

    The chemical compatibility of lithium with tows of carbon and aramid fibers and silicon carbide and boron monofilaments was investigated by encapsulating the fibers in liquid lithium and also by sintering. The lithium did not readily wet the various fibers. In particular, very little lithium infiltration into the carbon and aramid tows was achieved and the strength of the tows was seriously degraded. The strength of the boron and silicon carbide monofilaments, however, was not affected by the liquid lithium. Therefore lithium is not feasible as a matrix for carbon and aramid fibers, but a composite containing boron or silicon carbide fibers in a lithium matrix may be feasible for specialized applications.

  12. Decomposition of lithium amide and imide films on nickel

    NASA Astrophysics Data System (ADS)

    Engbæk, Jakob; Nielsen, Gunver; Nielsen, Jane H.; Chorkendorff, Ib

    2007-02-01

    Thin films of lithium hydride, lithium amide and lithium imide were grown from lithium and ammonia under controlled conditions in an ultra high vacuum chamber. By making thin films instead of bulk or powder samples, it was possible to study the stability and the release of hydrogen without influence of transport phenomena. Surprisingly, lithium amide and lithium imide were seen to decompose at higher temperatures than lithium hydride. Furthermore, it was seen that hydrogen reversibly could be removed by heat treatment and subsequently refilled.

  13. Stable Lithium Deposition Generated from Ceramic-Cross-Linked Gel Polymer Electrolytes for Lithium Anode.

    PubMed

    Tsao, Chih-Hao; Hsiao, Yang-Hung; Hsu, Chun-Han; Kuo, Ping-Lin

    2016-06-22

    In this work, a composite gel electrolyte comprising ceramic cross-linker and poly(ethylene oxide) (PEO) matrix is shown to have superior resistance to lithium dendrite growth and be applicable to gel polymer lithium batteries. In contrast to pristine gel electrolyte, these nanocomposite gel electrolytes show good compatibility with liquid electrolytes, wider electrochemical window, and a superior rate and cycling performance. These silica cross-linkers allow the PEO to form the lithium ion pathway and reduce anion mobility. Therefore, the gel not only features lower polarization and interfacial resistance, but also suppresses electrolyte decomposition and lithium corrosion. Further, these nanocomposite gel electrolytes increase the lithium transference number to 0.5, and exhibit superior electrochemical stability up to 5.0 V. Moreover, the lithium cells feature long-term stability and a Coulombic efficiency that can reach 97% after 100 cycles. The SEM image of the lithium metal surface after the cycling test shows that the composite gel electrolyte with 20% silica cross-linker forms a uniform passivation layer on the lithium surface. Accordingly, these features allow this gel polymer electrolyte with ceramic cross-linker to function as a high-performance lithium-ionic conductor and reliable separator for lithium metal batteries. PMID:27247991

  14. Process for recovering tritium from molten lithium metal

    DOEpatents

    Maroni, Victor A.

    1976-01-01

    Lithium tritide (LiT) is extracted from molten lithium metal that has been exposed to neutron irradiation for breeding tritium within a thermonuclear or fission reactor. The extraction is performed by intimately contacting the molten lithium metal with a molten lithium salt, for instance, lithium chloride - potassium chloride eutectic to distribute LiT between the salt and metal phases. The extracted tritium is recovered in gaseous form from the molten salt phase by a subsequent electrolytic or oxidation step.

  15. A preliminary deposit model for lithium-cesium-tantalum (LCT) pegmatites

    USGS Publications Warehouse

    Bradley, Dwight; McCauley, Andrew

    2013-01-01

    This report is part of an effort by the U.S. Geological Survey to update existing mineral deposit models and to develop new ones. We emphasize practical aspects of pegmatite geology that might directly or indirectly help in exploration for lithium-cesium-tantalum (LCT) pegmatites, or for assessing regions for pegmatite-related mineral resource potential. These deposits are an important link in the world’s supply chain of rare and strategic elements, accounting for about one-third of world lithium production, most of the tantalum, and all of the cesium.

  16. Lithium in surficial materials of the conterminous United States and partial data on cadmium

    USGS Publications Warehouse

    Shacklette, Hansford T.; Boerngen, J.G.; Cahill, J.P.; Rahill, R.L.

    1973-01-01

    Concentrations of lithium in 912 samples of soils and other regoliths from sites approximately 50 miles apart throughout the United States are represented on a map by symbols showing five ranges of values. A histogram of the lithium concentrations is also given. The geometric mean lithium concentration is 20.4 ppm (parts per million) for all samples, 17.3 ppm for samples from the Eastern United States, and 23.3 ppm for samples from the Western United States. Cadmium concentrations were less than 1 ppm in all but 11 of the 912 samples. Ten of these 11 samples contained from 1 to 1.5 ppm cadmium; one sample contained 10 ppm cadmium.

  17. Lithium: Is It Possible to Generate It at the Stellar Surfaces?

    NASA Astrophysics Data System (ADS)

    Gopka, V. F.; Yushchenko, A. V.; Shavrina, A. V.; Yushchenko, V. A.

    2014-08-01

    The possible mechanisms of lithium production in stars of different types and ages remain completely unidentified up to now. We proposed the scenario of lithium production in multiple stellar systems at the evolutionary stages when one of the components is a young neutron star (NS). In this case the source of lithium is the result of irradiation of surface of optical star by high-energy particles accelerated to relativistic velocities in the inner parts of the accretion disk around a NS. We show that the understanding of the evolutionary phase of Li-rich stars is impossible without the understanding of evolutionary state of stars, containing no lithium. Accepting the idea of explanation the observed properties of lithium in the magnetic chemically peculiar (MCP) stars by the hypothesis of a double (multiple) stellar system with NS companion, it is possible to clarify the evolutionary state of Li-rich, Herbig AeBe, and T Tau type stars and the origin of related stellar groups such as HgMn, AmFm, and δ Scuti type stars.

  18. Formulation, physicochemical characterization and stability study of lithium-loaded microemulsion system.

    PubMed

    Mouri, Abdelkader; Legrand, Philippe; El Ghzaoui, Abdeslam; Dorandeu, Christophe; Maurel, Jean Claude; Devoisselle, Jean-Marie

    2016-04-11

    Lithium biocompatible microemulsion based on Peceol(®), lecithin, ethanol and water was studied in attempt to identify the optimal compositions in term of drug content, physicochemical properties and stability. Lithium solubilization in microemulsion was found to be compatible with a drug-surfactant binding model. Lithium ions were predominantly solubilized within lecithin head group altering significantly the interfacial properties of the system. Pseudo-ternary phase diagrams of drug free and drug loaded microemulsions were built at constant ethanol/lecithin weight ratio (40/60). Lithium loaded microemulsion has totally disappeared in the Peceol(®) rich part of phase diagram; critical fractions of lecithin and ethanol were required for the formation of stable microemulsion. The effect of lithium concentration on the properties and physical stability of microemulsions were studied using microscopy, Karl Fischer titrations, rheology analyses, conductivity measurements and centrifugation tests. The investigated microemulsions were found to be stable under accelerated storage conditions. The systems exhibited low viscosity and behaved as Newtonian fluid and no structural transition was shown. PMID:26836707

  19. Surface Treatment of a Lithium Limiter for Spherical Torus Plasma Experiments

    SciTech Connect

    Kaita, R.; Majeski, R.; Doerner, R.; Antar, G.; Timberlake, J.; Spaleta, J.; Hoffman, D.; Jones, B.; Munsat, T.; Kugel, H.; Taylor, G.; Stutman, D.; Soukhanovskii, V.; Maingi, R.; Molesa, S.; Efthimion, P.; Menard, J.; Finkenthal, M.; Luckhardt, S.

    2001-03-20

    The concept of a flowing lithium first wall for a fusion reactor may lead to a significant advance in reactor design, since it could virtually eliminate the concerns with power density and erosion, tritium retention, and cooling associated with solid walls. As part of investigations to determine the feasibility of this approach, plasma interaction questions in a toroidal plasma geometry are being addressed in the Current Drive eXperiment-Upgrade (CDX-U) spherical torus (ST). The first experiments involved a toroidally local lithium limiter (L3). Measurements of pumpout rates indicated that deuterium pumping was greater for the L3 compared to conventional boron carbide limiters. The difference in the pumpout rates between the two limiter types decreased with plasma exposure, but argon glow discharge cleaning was able to restore the pumping effectiveness of the L3. At no point, however, was the extremely low recycling regime reported in previous lithium experiments achieved. This may be due to the much larger lithium surfaces that were exposed to the plasma in the earlier work. The possibility will be studied in the next set of CDX-U experiments, which are to be conducted with a large area, fully toroidal lithium limiter.

  20. Electrophoretic lithium iron phosphate/reduced graphene oxide composite for lithium ion battery cathode application

    NASA Astrophysics Data System (ADS)

    Huang, Yuan; Liu, Hao; Lu, Yi-Chun; Hou, Yanglong; Li, Quan

    2015-06-01

    A binder/additive free composite electrode of lithium iron phosphate/reduced graphene oxide with ultrahigh lithium iron phosphate mass ratio (91.5 wt% of lithium iron phosphate) is demonstrated using electrophoresis. The quasi-spherical lithium iron phosphate particles are uniformly connected to and/or wrapped by three-dimensional networks of reduced graphene oxide nanosheets, with intimate contact formed between the two. Enhanced capacity is achieved in the electrophoretic composite cathode, when compared to either the conventional one or composite cathode formed by mechanically mixing lithium iron phosphate and reduced graphene oxide. The present methodology is simple and does not disturb the active material growth process. It can be generally applied to a variety of active material systems for both cathode and anode applications in lithium ion batteries.

  1. Lithium protects ethanol-induced neuronal apoptosis

    SciTech Connect

    Zhong Jin . E-mail: jizhong@iupui.edu; Yang Xianlin; Yao Weiguo; Lee Weihua

    2006-12-01

    Lithium is widely used for the treatment of bipolar disorder. Recent studies have demonstrated its neuroprotective effect. Ethanol is a potent neurotoxin that is particularly harmful to the developing nervous system. In this study, we evaluated lithium's neuroprotection against ethanol-induced apoptosis. Transient exposure of infant mice to ethanol caused apoptotic cell death in brain, which was prevented significantly by administering a low dose of lithium 15 min later. In cultured cerebellar granule neurons, ethanol-induced apoptosis and activation of caspase-3/9, both of which were prevented by lithium. However, lithium's protection is not mediated by its commonly known inhibition of glycogen synthase3{beta}, because neither ethanol nor lithium has significant effects on the phosphorylation of Akt (ser473) or GSK3{beta} (ser9). In addition, the selective GSK-3{beta} inhibitor SB-415286 was unable to prevent ethanol-induced apoptosis. These data suggest lithium may be used as a potential preventive measure for ethanol-induced neurological deficits.

  2. Lithium Manganese Silicate Positive Electrode Material

    NASA Astrophysics Data System (ADS)

    Yang, Qiong

    As the fast development of the electronic portable devices and drastic fading of fossil energy sources. The need for portable secondary energy sources is increasingly urgent. As a result, lithium ion batteries are being investigated intensely to meet the performance requirements. Among various electrode materials, the most expensive and capacity limiting component is the positive materials. Based on this, researches have been mostly focused on the development of novel cathode materials with high capacity and energy density and the lithium transition metal orthosilicates have been identified as possible high performance cathodes. Here in, we report the synthesis of a kind of lithium transition metal orthosilicates electrode lithium manganese silicate. Lithium manganese silicate has the advantage of high theoretical capacity, low cost raw material and safety. In this thesis, lithium manganese silicate are prepared using different silicon sources. The structure of silicon sources preferred are examined. Nonionic block copolymers surfactant, P123, is tried as carbon source and mophology directing agent. Lithium manganese silicate's performances are improved by adding P123.

  3. A Molecular Model for Lithium's Bioactive Form.

    PubMed

    Briggs, Katharine T; Giulian, Gary G; Li, Gong; Kao, Joseph P Y; Marino, John P

    2016-07-26

    Lithium carbonate, a drug for the treatment of bipolar disorder, provides mood stability to mitigate recurrent episodes of mania and/or depression. Despite its long-term and widespread use, the mechanism by which lithium acts to elicit these psychological changes has remained unknown. Using nuclear magnetic resonance (NMR) methods, in this study we characterized the association of lithium with adenosine triphosphate (ATP) and identified a bimetallic (Mg·Li) ATP complex. Lithium's affinity to form this complex was found to be relatively high (Kd ∼1.6 mM) compared with other monovalent cations and relevant, considering lithium dosing and physiological concentrations of Mg(2+) and ATP. The ATP·Mg·Li complex reveals, for the first time, to the best of our knowledge, that lithium can associate with magnesium-bound phosphate sites and then act to modulate purine receptor activity in neuronal cells, suggesting a molecular mode for in vivo lithium action. PMID:27463132

  4. JPL lithium doped solar cell development program

    NASA Technical Reports Server (NTRS)

    Berman, P. A.

    1972-01-01

    One of the most significant problems encountered in the use of silicon solar cells in space is the sensitivity of the device to electron and proton radiation exposure. The p-diffused-into-n-base solar cells were replaced with the more radiation tolerant n-diffused-into-p-base solar cells. Another advancement in achieving greater radiation tolerance was the discovery that the addition of lithium to n-base silicon resulted in what appeared to be annealing of radiation-induced defects. This phenomenon is being exploited to develop a high efficiency radiation resistant lithium-doped solar cell. Lithium-doped solar cells fabricated from oxygen-lean and oxygen-rich silicon were obtained with average initial efficiencies of 11.9% at air mass zero and 28 C, as compared to state-of-the-art n-p cells fabricated from 10 ohm cm silicon with average efficiencies of 11.3% under similar conditions. Lithium-doped cells demonstrated the ability to withstand three to five times the fluence of 1-MeV electrons before degrading to a power equivalent to state-of-the-art solar cells. The principal investigations are discussed with respect to fabrication of high efficiency radiation resistant lithium-doped cells, including starting material, p-n junction diffusion, lithium source introduction, and lithium diffusion.

  5. High Performance Discharges in the Lithium Tokamak eXperiment (LTX) with Liquid Lithium Walls

    NASA Astrophysics Data System (ADS)

    Schmitt, John

    2014-10-01

    The possibility of a liquid metal first wall for a fusion reactor has been extensively discussed. Small-area liquid lithium limiters and divertor targets have been installed in tokamaks, but no confinement device has ever operated with a large-area liquid lithium wall. Here we report the first-ever successful operation of a tokamak with a large area (2 m2, or 40% of the total plasma surface area) liquid lithium wall in the Lithium Tokamak eXperiment (LTX). These results were obtained with a new, electron beam-based lithium evaporation system, which can deposit a lithium coating on the hot (300 C) wall of LTX in a five-minute period. Preliminary analyses of diamagnetic and other data for discharges operated with a liquid lithium wall indicate that confinement times increased by 10 × compared to discharges with helium-dispersed solid lithium coatings. Ohmic confinement times exceeded ITER98P(y,2) scaling by up to a factor of four. LTX lacks auxiliary heating, so these confinement improvements represent changes in electron confinement. Spectroscopic analysis of the discharges using the John Hopkins University transmission grating extreme ultraviolet spectrometer indicates that oxygen levels in the discharges run against liquid walls were significantly reduced compared to discharges operated against solid lithium walls. This differs strongly from earlier trials of molten lithium walls in LTX, which showed evidence for strong oxygen influx from walls operated at similar temperatures. At present, the Thomson scattering system is undergoing upgrades and realignment, after which confinement times obtained with magnetic diagnostics will be compared with kinetic measurements. A second electron beam will be installed to extend liquid lithium wall operation to 4 m2 coverage, or >80% of the total plasma surface area. Results with expanded liquid lithium wall area will be presented. Supported by US DOE Contracts DE-AC02-09CH11466 and DE-AC52-07NA27344.

  6. Lithium D-cell study

    NASA Technical Reports Server (NTRS)

    Size, P.; Takeuchi, Esther S.

    1993-01-01

    The purpose of this contract is to evaluate parametrically the effects of various factors including the electrolyte type, electrolyte concentration, depolarizer type, and cell configuration on lithium cell electrical performance and safety. This effort shall allow for the selection and optimization of cell design for future NASA applications while maintaining close ties with WGL's continuous improvements in manufacturing processes and lithium cell design. Taguchi experimental design techniques are employed in this task, and allow for a maximum amount of information to be obtained while requiring significantly less cells than if a full factorial design were employed. Acceptance testing for this task is modeled after the NASA Document EP5-83-025, Revision C, for cell weights, OCV's and load voltages. The performance attributes that are studied in this effort are fresh capacity and start-up characteristics evaluated at two rates and two temperatures, shelf-life characteristics including start-up and capacity retention, and iterative microcalorimetry measurements. Abuse testing includes forced over discharge at two rates with and without diode protection, temperature tolerance testing, and shorting tests at three rates with the measurement of heat generated during shorting conditions.

  7. The Lithium Vapor Box Divertor

    NASA Astrophysics Data System (ADS)

    Goldston, Robert; Hakim, Ammar; Hammett, Gregory; Jaworski, Michael; Myers, Rachel; Schwartz, Jacob

    2015-11-01

    Projections of scrape-off layer width to a demonstration power plant suggest an immense parallel heat flux, of order 12 GW/m2, which will necessitate nearly fully detached operation. Building on earlier work by Nagayama et al. and by Ono et al., we propose to use a series of differentially pumped boxes filled with lithium vapor to isolate the buffering vapor from the main plasma chamber, allowing stable detachment. This powerful differential pumping is only available for condensable vapors, not conventional gases. We demonstrate the properties of such a system through conservation laws for vapor mass and enthalpy, and then include plasma entrainment and ultimately an estimate of radiated power. We find that full detachment should be achievable with little leakage of lithium to the main plasma chamber. We also present progress towards solving the Navier-Stokes equation numerically for the chain of vapor boxes, including self-consistent wall boundary conditions and fully-developed shocks, as well as concepts for an initial experimental demonstration-of-concept. This work supported by DOE Contract No. DE-AC02-09CH11466.

  8. Lithium D-cell study

    NASA Astrophysics Data System (ADS)

    Size, P.; Takeuchi, Esther S.

    1993-03-01

    The purpose of this contract is to evaluate parametrically the effects of various factors including the electrolyte type, electrolyte concentration, depolarizer type, and cell configuration on lithium cell electrical performance and safety. This effort shall allow for the selection and optimization of cell design for future NASA applications while maintaining close ties with WGL's continuous improvements in manufacturing processes and lithium cell design. Taguchi experimental design techniques are employed in this task, and allow for a maximum amount of information to be obtained while requiring significantly less cells than if a full factorial design were employed. Acceptance testing for this task is modeled after the NASA Document EP5-83-025, Revision C, for cell weights, OCV's and load voltages. The performance attributes that are studied in this effort are fresh capacity and start-up characteristics evaluated at two rates and two temperatures, shelf-life characteristics including start-up and capacity retention, and iterative microcalorimetry measurements. Abuse testing includes forced over discharge at two rates with and without diode protection, temperature tolerance testing, and shorting tests at three rates with the measurement of heat generated during shorting conditions.

  9. Improved Separators For Rechargeable Lithium Cells

    NASA Technical Reports Server (NTRS)

    Shen, David; Surampudi, Subbarao; Huang, Chen-Kuo; Halpert, Gerald

    1994-01-01

    Improved pairs of separators proposed for use in rechargeable lithium cells operating at ambient temperature. Block growth of lithium dendrites and help prevent short circuits. Each cell contains one separator made of microporous polypropylene placed next to anode, and one separator made of microporous polytetrafluoroethylene (PTFE) next to cathode. Separators increase cycle lives of secondary lithium cells. Cells to which concept applicable those of Li/TiS(2), Li/NbSe(3), Li/CoO(2), Li/MoS(2), Li/VO(x), and Li/MnO(2) chemical systems. Advantageous in spacecraft, military, communications, automotive, and other applications in which high energy density and rechargeability needed.

  10. Lithium in Stellar Atmospheres: Observations and Theory

    NASA Astrophysics Data System (ADS)

    Lyubimkov, L. S.

    2016-09-01

    Of all the light elements, lithium is the most sensitive indicator of stellar evolution. This review discusses current data on the abundance of lithium in the atmospheres of A-, F-, G-, and K-stars of different types, as well as the consistency of these data with theoretical predictions. The variety of observed Li abundances is illustrated by the following objects in different stages of evolution: (1) Old stars in the galactic halo, which have a lithium abundance logɛ(Li)=2.2 (the "lithium plateau") that appears to be 0.5 dex lower than the primordial abundance predicted by cosmological models. (2) Young stars in the galactic disk, which have been used to estimate the contemporary initial lithium abundance logɛ(Li)=3.2±0.1 for stars in the Main sequence. Possible sources of lithium enrichment in the interstellar medium during evolution of the galaxy are discussed. (3) Evolving FGK dwarfs in the galactic disk, which have lower logɛ(Li) for lower effective temperature T eff and mass M. The "lithium dip" near T eff ~6600 K in the distribution of logɛ(Li) with respect to T eff in old clusters is discussed. (4) FGK giants and supergiants, of which most have no lithium at all. This phenomenon is consistent with rotating star model calculations. (5) Lithium rich cold giants with logɛ(Li) ≥ 2.0, which form a small, enigmatic group. Theoretical models with rotation can explain the existence of these stars only in the case of low initial rotation velocities V 0 <50 km/s. In all other cases it is necessary to assume recent synthesis of lithium (capture of a giant planet is an alternative). (6) Magnetic Ap-stars, where lithium is concentrated in spots located at the magnetic poles. There the lithium abundance reaches logɛ(Li)=6. Discrepancies between observations and theory are noted for almost all the stars discussed in this review.

  11. Diffusion of lithium in titanium oxide

    NASA Astrophysics Data System (ADS)

    Shea, Patrick; Ye, Jianchao; Wood, Brandon; Bonev, Stanimir

    Titanium oxide has generated interest lately as a promising anode candidate for use in lithium-ion batteries. We report first principles calculations on the mobility of lithium atoms in both crystalline and amorphous phases of titanium oxide. Density functional theory calculations of structural properties and diffusion energy barriers are combined with rate theory and a lattice gas model to study diffusion of lithium over a range of concentrations. A summary of results, including significant differences in the mobility between amorphous and crystalline phases, will be presented and discussed.

  12. Lithium electronic environments in rechargeable battery electrodes

    NASA Astrophysics Data System (ADS)

    Hightower, Adrian

    This work investigates the electronic environments of lithium in the electrodes of rechargeable batteries. The use of electron energy-loss spectroscopy (EELS) in conjunction with transmission electron microscopy (TEM) is a novel approach, which when coupled with conventional electrochemical experiments, yield a thorough picture of the electrode interior. Relatively few EELS experiments have been preformed on lithium compounds owing to their reactivity. Experimental techniques were established to minimize sample contamination and control electron beam damage to studied compounds. Lithium hydroxide was found to be the most common product of beam damaged lithium alloys. Under an intense electron beam, halogen atoms desorbed by radiolysis in lithium halides. EELS spectra from a number of standard lithium compounds were obtained in order to identify the variety of spectra encountered in lithium rechargeable battery electrodes. Lithium alloys all displayed characteristically broad Li K-edge spectra, consistent with transitions to continuum states. Transitions to bound states were observed in the Li K and oxygen K-edge spectra of lithium oxides. Lithium halides were distinguished by their systematic chemical shift proportional to the anion electronegativity. Good agreement was found with measured lithium halide spectra and electron structure calculations using a self-consistant multiscattering code. The specific electrode environments of LiC6, LiCoO2, and Li-SnO were investigated. Contrary to published XPS predictions, lithium in intercalated graphite was determined to be in more metallic than ionic. We present the first experimental evidence of charge compensation by oxygen ions in deintercalated LiCoO2. Mossbauer studies on cycled Li-SnO reveal severely defective structures on an atomic scale. Metal hydride systems are presented in the appendices of this thesis. The mechanical alloying of immiscible Fe and Mg powders resulted in single-phase bcc alloys of less than 20

  13. Lithium batteries with organic slurry cathodes

    SciTech Connect

    Bruder, A.H.

    1986-04-01

    This patent describes a laminar electrical cell. This cell consists of a sheet of conductive plastic, a separator, a cathode consisting essentially of a slurry of dewatered MnO/sub 2/ and carbon particles in a solution of a lithium salt in a substantially anhydrous organic solvent between and in contact with the conductive plastic sheet and the separator with the solution permeating the separator. The slurry is free of any binder material, and a thin sheet of lithium is in contact with the separator. The separator being interposed between the cathode and the lithium sheet.

  14. Water structure in concentrated lithium chloride solutions

    NASA Astrophysics Data System (ADS)

    Tromp, R. H.; Neilson, G. W.; Soper, A. K.

    1992-06-01

    The radial pair distribution functions gHH(r) and gOH(r) (to a good approximation) of 1 and 10 m solutions of lithium chloride in water have been obtained from neutron diffraction. It turns out that the intermolecular water structure in a solution of 10 m is affected considerably by the presence of ions—the number of hydrogen bonds is about 70% lower than in pure water. The intermolecular water structure in 1 m lithium chloride as well as the intramolecular water structure in both 1 and 10 m lithium chloride is not distinguishable from that of pure water in any measurable extent.

  15. Lithium iodide cardiac pacemakers: initial clinical experience.

    PubMed Central

    Burr, L. H.

    1976-01-01

    A new long-life cardiac pacemaker pulse generator powered by a lithium iodide fuel cell was introduced in Canada in 1973. The compact, hermetically sealed unit is easily implanted and reliable, has excellent patient acceptance and has an anticipated battery life of almost 14 years. Among 105 patients who received a lithium iodide pacemaker, complications occurred in 18. The lithium iodide pacemaker represents a significant advance in pacemaker generator technology and is recommended for long-term cardiac pacing; the manufacturer guarantees the pulse generator for 6 years. Images FIG. 1 PMID:974965

  16. Possible nephotoxic interaction of lithium and metronidazole

    SciTech Connect

    Teicher, M.H.; Altesman, R.I.; Cole, J.O.; Schatzberg, A.F.

    1987-06-26

    Several classes of drugs can promote renal retention of lithium and, occasionally, can induce lithium intoxication. The antimicrobial agent metronidazole hydrochloride (Flagyl I.V.) was also implicated in producing such a reaction in one woman. The authors describe two patients who experienced toxic reactions to lithium following brief use of metronidazole. However, in these two patients, in contrast to the previous case, the degree of acute intoxication was less severe and treatment with metronidazole was completed without apparent suspicion, but persistent signs of renal damage later emerged.

  17. ASSESSMENT OF LITHIUM USING THE IEHR EVALUATIVE PROCESS FOR ASSESSING HUMAN DEVELOPMENTAL AND REPRODUCTIVE TOXICITY OF AGENTS

    EPA Science Inventory

    This document presents an evaluation of the reproductive and developmental effects of lithium and reviews toxicologic information on several specific lithium salts: ithium carbonate, lithium chloride, lithium citrate, and lithium hypochlorite. ithium (Li), an alkali metal, is a n...

  18. Unrecognized delayed toxic lithium peak concentration in an acute poisoning with sustained release lithium product.

    PubMed

    Borrás-Blasco, Joaquín; Sirvent, Ana Esther; Navarro-Ruiz, Andrés; Murcia-López, Ana; Romero-Crespo, Isabel; Enriquez, Ricardo

    2007-03-01

    A 32-year-old female with a history of bipolar disorder was admitted after taking approximately 16 g of an extended-release lithium carbonate formulation in an attempted suicide. Five hours after consumption, the lithium serum level was 3.2 mEq/L. Fourteen hours after consumption, the lithium level was 5.1 mEq/L and the patient was asymptomatic. Due to a level > 4 mEq/L, the patient was transferred to a renal medicine service for hemodialysis. The lithium concentration 6 hours after the hemodialysis was 2.54 mEq/L. Thirty seven hours after the consumption (15 hours after hemodialysis), lithium levels increased up to 6.09 mEq/L. A second hemodialysis session was performed, which successfully reduced the serum lithium concentration to 1.86 mEq/L. Lithium levels 85 hours after the consumption were 0.61 mEq/L and the patient was transferred to the Psychiatry Department. Unrecognized delayed toxic peak lithium concentration may appear in an acute poisoning with a sustained release lithium product. Therefore, patients presenting with acute intoxication with extended release formulations should be managed with caution, and continued drug monitoring is suggested. PMID:17396741

  19. Modeling Lithium Movement over Multiple Cycles in a Lithium-Metal Battery

    SciTech Connect

    Ferrese, A; Newman, J

    2014-04-11

    This paper builds on the work by Ferrese et al. [J. Electrochem., 159, A1615 (2012)], where a model of a lithium-metal battery with a LiyCoO2 positive electrode was created in order to predict the movement of lithium in the negative electrode along the negative electrode/separator interface during cell cycling. In this paper, the model is expanded to study the movement of lithium along the lithium-metal anode over multiple cycles. From this model, it is found that when a low percentage of lithium at the negative electrode is utilized, the movement of lithium along the negative electrode/separator interface reaches a quasi steady state after multiple cycles. This steady state is affected by the slope of the open-circuit-potential function in the positive electrode, the rate of charge and discharge, the depth of discharge, and the length of the rest periods. However, when a high percent of the lithium at the negative electrode is utilized during cycling, the movement does not reach a steady state and pinching can occur, where the lithium nearest the negative tab becomes progressively thinner after cycling. This is another nonlinearity that leads to a progression of the movement of lithium over multiple cycles. (C) 2014 The Electrochemical Society.

  20. Electrolytic method for the production of lithium using a lithium-amalgam electrode

    DOEpatents

    Cooper, John F.; Krikorian, Oscar H.; Homsy, Robert V.

    1979-01-01

    A method for recovering lithium from its molten amalgam by electrolysis of the amalgam in an electrolytic cell containing as a molten electrolyte a fused-salt consisting essentially of a mixture of two or more alkali metal halides, preferably alkali metal halides selected from lithium iodide, lithium chloride, potassium iodide and potassium chloride. A particularly suitable molten electrolyte is a fused-salt consisting essentially of a mixture of at least three components obtained by modifying an eutectic mixture of LiI-KI by the addition of a minor amount of one or more alkali metal halides. The lithium-amalgam fused-salt cell may be used in an electrolytic system for recovering lithium from an aqueous solution of a lithium compound, wherein electrolysis of the aqueous solution in an aqueous cell in the presence of a mercury cathode produces a lithium amalgam. The present method is particularly useful for the regeneration of lithium from the aqueous reaction products of a lithium-water-air battery.

  1. Lithium in drinking water and suicide mortality: interplay with lithium prescriptions

    PubMed Central

    Helbich, Marco; Leitner, Michael; Kapusta, Nestor D.

    2015-01-01

    Background Little is known about the effects of lithium intake through drinking water on suicide. This intake originates either from natural rock and soil elution and/or accumulation of lithium-based pharmaceuticals in ground water. Aims To examine the interplay between natural lithium in drinking water, prescribed lithium-based pharmaceuticals and suicide in Austria. Method Spatial Bayesian regressions for males, females and pooled suicide mortality rates were estimated. Results Although the expected inverse association between lithium levels in drinking water and suicide mortality was confirmed for males and for total suicide rates, the relationship for females was not significant. The models do not indicate that lithium from prescriptions, assumed to accumulate in drinking water, is related to suicide risk patterns either as an individual effect or as a moderator of lithium levels in drinking water. Gender-specific differences in risk factors and local risk hot spots are confirmed. Conclusions The findings do not support the hypotheses that lithium prescriptions have measureable protective effects on suicide or that they interact with lithium in drinking water. PMID:25953888

  2. A rapid method for the determination of lithium transference numbers

    SciTech Connect

    Zawodzinski, T.A. Jr.; Dai, H.; Sanderson, S.; Davey, J.; Uribe, F.

    1997-05-01

    Lithium ion-conducting polymer electrolytes are of increasing interest for use in lithium-polymer batteries. Lithium transference numbers, the net fraction of current carried by lithium in a cell, are key figures of merit for potential lithium battery electrolytes. The authors describe the Electrophoretic NMR (ENMR) method for the determination of lithium ion transference numbers (T{sub Li}). The work presented is a proof-of-concept of the application of the ENMR method to lithium ion transference measurements for several different lithium salts in gelled electrolytes. The NMR method allows accurate determination of T{sub Li} values, as indicated by the similarity of T{sub Li} in the gelled electrolytes to those in aqueous electrolyte solutions at low salt concentration. Based on calculated tradeoffs of various experimental parameters, they also discuss some conclusions concerning the range of applicability of the method to other electrolytes with lower lithium mobility.

  3. Lithium-Based High Energy Density Flow Batteries

    NASA Technical Reports Server (NTRS)

    Bugga, Ratnakumar V. (Inventor); West, William C. (Inventor); Kindler, Andrew (Inventor); Smart, Marshall C. (Inventor)

    2014-01-01

    Systems and methods in accordance with embodiments of the invention implement a lithium-based high energy density flow battery. In one embodiment, a lithium-based high energy density flow battery includes a first anodic conductive solution that includes a lithium polyaromatic hydrocarbon complex dissolved in a solvent, a second cathodic conductive solution that includes a cathodic complex dissolved in a solvent, a solid lithium ion conductor disposed so as to separate the first solution from the second solution, such that the first conductive solution, the second conductive solution, and the solid lithium ionic conductor define a circuit, where when the circuit is closed, lithium from the lithium polyaromatic hydrocarbon complex in the first conductive solution dissociates from the lithium polyaromatic hydrocarbon complex, migrates through the solid lithium ionic conductor, and associates with the cathodic complex of the second conductive solution, and a current is generated.

  4. Conductivity and self-diffusivity measurements on molten lithium electrolytes for battery applications

    NASA Astrophysics Data System (ADS)

    Videa, Marcelo Vargas

    Several lithium salt systems, classified in this work as solvent-free and solvent containing, have been investigated with the purpose of determining their qualities as potential electrolytes for applications in lithium batteries. With this objective, their thermal. properties, of which the glassforming ability was considered of fundamental importance, and their experimental conductivities and lithium self-diffusivities were determined to build a body of information that could be considered complete insofar as the evaluation of the material was concerned. Mixtures of lithium salts with fluorine-based anions, including LiCF 3SO3, LiBF4 and LiN(SO2CF3) 2 (or LiIm), were studied as part of a search for chemically and electrochemically stable glassforming lithium salts. Although the observation of the glassforming ability of some binary and ternary systems was considered a partial success, the high glass transition temperatures recorded and their inability to avoid crystallization discouraged the author from any attempt of using these materials as practical electrolytes. Attention was then placed on a family of tetrahaloaluminate lithium salts among which LiAlCl4, although non-glassforming when pure, can be easely vitrified upon the addition of small amounts of a second component or plasticizing agent. By extrapolation to zero content of plasticizing agent it was found that Tg for this salt is -35°C, the lowest value recorded for an ionic system. Although the LiAlCl4-based systems obtained by introducing LiIm, LiIm-AlCl3 or LiAl(SO3Cl)4 as second components produce room temperature, non-crystallizing liquids, they unfortunately fail in providing conductivities with values acceptable for the applications intended. In the case of the system LiAlC14-LiAl(SO3Cl) 4, lithium self-diffusivity measurements are compared via the Nernst-Einstein relation to the conductivity values in order to obtain insight on lithium-ion transport properties. Solvent-containing electrolytes

  5. An approach to beneficiation of spent lithium-ion batteries for recovery of materials

    NASA Astrophysics Data System (ADS)

    Marinos, Danai

    Lithium ion batteries are one of the most commonly used batteries. A large amount of these have been used over the past 25 years and the use is expected to rise more due to their use in automotive batteries. Lithium ion batteries cannot be disposed into landfill due to safety reasons and cost. Thus, over the last years, there has been a lot of effort to find ways to recycle lithium ion batteries. A lot of valuable materials are present in a lithium ion battery making their recycling favorable. Many attempts, including pyrometallurgical and hydrometallurgical methods, have been researched and some of them are already used by the industry. However, further improvements are needed to the already existing processes, to win more valuable materials, use less energy and be more environmentally benign. The goal of this thesis is to find a low-temperature, low-energy method of recovering lithium from the electrolyte and to develop pathways for complete recycling of the battery. The research consists of the following parts: Pure LiPF6 powder, which is the electrolyte material, was characterized using x- ray diffraction analysis and DSC/TGA analysis. The LiPF6 powder was titrated using acid (HCl, HNO3, H2SO4), bases (NH4 OH) and distilled water. It was concluded that distilled water was the best solvent to selectively leach lithium from lithium-ion batteries. Leaching conditions were optimized including time, temperature, solid/liquid ratio and stirring velocity. All the samples were tested using ICP for chemical composition. Because leaching could be performed at room temperature, leaching was conducted in a flotation machine that was able to separate plastics by creating bubbles with no excess reagents use. The solution that contained lithium had to be concentrated more in order for lithium to be able to precipitate and it was shown that the solution could be concentrated by using the same solution over and over again. The next set of experiments was composed of battery

  6. Lithium-cation conductivity and crystal structure of lithium diphosphate

    SciTech Connect

    Voronin, V.I.; Sherstobitova, E.A.; Blatov, V.A.; Shekhtman, G.Sh.

    2014-03-15

    The electrical conductivity of lithium diphosphate Li{sub 4}P{sub 2}O{sub 7} has been measured and jump-like increasing of ionic conductivity at 913 K has been found. The crystal structure of Li{sub 4}P{sub 2}O{sub 7} has been refined using high temperature neutron diffraction at 300–1050 K. At 913 K low temperature triclinic form of Li{sub 4}P{sub 2}O{sub 7} transforms into high temperature monoclinic one, space group P2{sub 1}/n, a=8.8261(4) Å, b=5.2028(4) Å, c=13.3119(2) Å, β=104.372(6)°. The migration maps of Li{sup +} cations based on experimental data implemented into program package TOPOS have been explored. It was found that lithium cations in both low- and high temperature forms of Li{sub 4}P{sub 2}O{sub 7} migrate in three dimensions. Cross sections of the migrations channels extend as the temperature rises, but at the phase transition point have a sharp growth showing a strong “crystal structure – ion conductivity” correlation. -- Graphical abstract: Crystal structure of Li{sub 4}P{sub 2}O{sub 7} at 950 K. Red balls represent oxygen atoms; black lines show Li{sup +} ion migration channels in the layers perpendicular to [001] direction. Highlights: • Structure of Li{sub 4}P{sub 2}O{sub 7} has been refined using high temperature neutron diffraction. • At 913 K triclinic form of Li{sub 4}P{sub 2}O{sub 7} transforms into high temperature monoclinic one. • The migration maps of Li{sup +} implemented into program package TOPOS have been explored. • Cross sections of the migrations channels at the phase transition have a sharp growth.

  7. A Polymer Lithium-Oxygen Battery.

    PubMed

    Elia, Giuseppe Antonio; Hassoun, Jusef

    2015-01-01

    Herein we report the characteristics of a lithium-oxygen battery using a solid polymer membrane as the electrolyte separator. The polymer electrolyte, fully characterized in terms of electrochemical properties, shows suitable conductivity at room temperature allowing the reversible cycling of the Li-O2 battery with a specific capacity as high as 25,000 mAh gC(-1) reflected in a surface capacity of 12.5 mAh cm(-2). The electrochemical formation and dissolution of the lithium peroxide during Li-O2 polymer cell operation is investigated by electrochemical techniques combined with X-ray diffraction study, demonstrating the process reversibility. The excellent cell performances in terms of delivered capacity, in addition to its solid configuration allowing the safe use of lithium metal as high capacity anode, demonstrate the suitability of the polymer lithium-oxygen as high-energy storage system. PMID:26238552

  8. Dosimetric properties of activated lithium tetraborate

    NASA Astrophysics Data System (ADS)

    Majchrowski, Andrzej; Malecki, M.; Zmija, Jozef; Warkocki, Stanislaw; Warkocki, Wodzislaw

    1993-10-01

    This paper describes preliminary investigations of Li2B4O7 thermoluminescent phosphors as candidates for gamma radiation dosimetry materials. Single crystals, glasses, and polycrystals of lithium tetraborate activated with different dopants have been investigated.

  9. Drug Interactions with Lithium: An Update.

    PubMed

    Finley, Patrick R

    2016-08-01

    Lithium has been used for the management of psychiatric illnesses for over 50 years and it continues to be regarded as a first-line agent for the treatment and prevention of bipolar disorder. Lithium possesses a narrow therapeutic index and comparatively minor alterations in plasma concentrations can have significant clinical sequelae. Several drug classes have been implicated in the development of lithium toxicity over the years, including diuretics and non-steroidal anti-inflammatory compounds, but much of the anecdotal and experimental evidence supporting these interactions is dated, and many newer medications and medication classes have been introduced during the intervening years. This review is intended to provide an update on the accumulated evidence documenting potential interactions with lithium, with a focus on pharmacokinetic insights gained within the last two decades. The clinical relevance and ramifications of these interactions are discussed. PMID:26936045

  10. Shock Induced Birefringence in Lithium Fluoride

    SciTech Connect

    Holmes, N C

    2001-06-01

    We have used an ellipsometer to measure the birefringence of lithium fluoride in shock compression experiments. In previous x-ray diffraction experiments, single crystal [100] LiF has been reported to remain cubic at moderate pressures.

  11. Lithium Circuit Test Section Design and Fabrication

    SciTech Connect

    Godfroy, Thomas; Garber, Anne; Martin, James

    2006-01-20

    The Early Flight Fission -- Test Facilities (EFF-TF) team has designed and built an actively pumped lithium flow circuit. Modifications were made to a circuit originally designed for NaK to enable the use of lithium that included application specific instrumentation and hardware. Component scale freeze/thaw tests were conducted to both gain experience with handling and behavior of lithium in solid and liquid form and to supply anchor data for a Generalized Fluid System Simulation Program (GFSSP) model that was modified to include the physics for freeze/thaw transitions. Void formation was investigated. The basic circuit components include: reactor segment, lithium to gas heat exchanger, electromagnetic (EM) liquid metal pump, load/drain reservoir, expansion reservoir, instrumentation, and trace heaters. This paper discusses the overall system design and build and the component testing findings.

  12. Lithium batteries: Status, prospects and future

    NASA Astrophysics Data System (ADS)

    Scrosati, Bruno; Garche, Jürgen

    Lithium batteries are characterized by high specific energy, high efficiency and long life. These unique properties have made lithium batteries the power sources of choice for the consumer electronics market with a production of the order of billions of units per year. These batteries are also expected to find a prominent role as ideal electrochemical storage systems in renewable energy plants, as well as power systems for sustainable vehicles, such as hybrid and electric vehicles. However, scaling up the lithium battery technology for these applications is still problematic since issues such as safety, costs, wide operational temperature and materials availability, are still to be resolved. This review focuses first on the present status of lithium battery technology, then on its near future development and finally it examines important new directions aimed at achieving quantum jumps in energy and power content.

  13. Aluminum-lithium alloys in helicopters

    SciTech Connect

    Smith, A.F.

    1997-10-01

    Aluminium-lithium alloys are widely applied on the EH101 helicopter, designed and built jointly by GKN Westland Helicopters of England and Agusta S.p.A. of Italy. With the exception of the powder metallurgy alloy AA 5091, all the current commercially available aluminum-lithium alloys are produced by direct-chill casting, and require a precipitation-aging heat treatment to achieve the required properties. In aluminum-lithium alloys containing greater than 1.3% (by weight) of lithium, the intermetallic phase {delta}{prime}-Al{sub 3}Li precipitates upon natural or artificial aging, but the associated strengthening effect is insufficient to meet the medium or high strength levels usually required (the damage tolerant temper in AA 8090 is an exception).

  14. Lithium Circuit Test Section Design and Fabrication

    NASA Technical Reports Server (NTRS)

    Godfroy, Thomas; Garber, Anne

    2006-01-01

    The Early Flight Fission - Test Facilities (EFF-TF) team has designed and built an actively pumped lithium flow circuit. Modifications were made to a circuit originally designed for NaK to enable the use of lithium that included application specific instrumentation and hardware. Component scale freeze/thaw tests were conducted to both gain experience with handling and behavior of lithium in solid and liquid form and to supply anchor data for a Generalized Fluid System Simulation Program (GFSSP) model that was modified to include the physics for freeze/thaw transitions. Void formation was investigated. The basic circuit components include: reactor segment, lithium to gas heat exchanger, electromagnetic (EM) liquid metal pump, load/drain reservoir, expansion reservoir, instrumentation, and trace heaters. This paper will discuss the overall system design and build and the component testing findings.

  15. Cells containing solvated electron lithium negative electrodes

    NASA Astrophysics Data System (ADS)

    Uribe, Francisco A.; Semkow, Krystyna W.; Sammells, Anthony F.

    1989-12-01

    This paper presents results obtained on cells based on solvated electron lithium negative electrodes, which may have application in high-energy-density secondary or reserve battery systems. The approach uses Li initially dissolved in liquid ammonia to give a solvated electron lithium/ammonia solution. This liquid negative active material is protected from direct contact with the liquid nonaqueous electrolyte in the positive electrode compartment by a lithium-intercalated electronically conducting ceramic membrane possessing Li(x)WoO2 composition with x values between 0.1 and 1.0. Depending upon initial lithium activity in the negative electrode compartments, the experimental cell was found to possess an initial open-circuit potential between 2.1 and 2.5 V.

  16. Lightweight magnesium-lithium alloys show promise

    NASA Technical Reports Server (NTRS)

    Adams, W. T.; Cataldo, C. E.

    1964-01-01

    Evaluation tests show that magnesium-lithium alloys are lighter and more ductile than other magnesium alloys. They are being used for packaging, housings, containers, where light weight is more important than strength.

  17. Catastrophic event modeling. [lithium thionyl chloride batteries

    NASA Technical Reports Server (NTRS)

    Frank, H. A.

    1981-01-01

    A mathematical model for the catastrophic failures (venting or explosion of the cell) in lithium thionyl chloride batteries is presented. The phenomenology of the various processes leading to cell failure is reviewed.

  18. NSTX Plasma Response to Lithium Coated Divertor

    SciTech Connect

    H.W. Kugel, M.G. Bell, J.P. Allain, R.E. Bell, S. Ding, S.P. Gerhardt, M.A. Jaworski, R. Kaita, J. Kallman, S.M. Kaye, B.P. LeBlanc, R. Maingi, R. Majeski, R. Maqueda, D.K. Mansfield, D. Mueller, R. Nygren, S.F. Paul, R. Raman, A.L. Roquemore, S.A. Sabbagh, H. Schneider, C.H. Skinner, V.A. Soukhanovskii, C.N. Taylor, J.R. Timberlak, W.R. Wampler, L.E. Zakharov, S.J. Zweben, and the NSTX Research Team

    2011-01-21

    NSTX experiments have explored lithium evaporated on a graphite divertor and other plasma facing components in both L- and H- mode confinement regimes heated by high-power neutral beams. Improvements in plasma performance have followed these lithium depositions, including a reduction and eventual elimination of the HeGDC time between discharges, reduced edge neutral density, reduced plasma density, particularly in the edge and the SOL, increased pedestal electron and ion temperature, improved energy confinement and the suppression of ELMs in the H-mode. However, with improvements in confinement and suppression of ELMs, there was a significant secular increase in the effective ion charge Zeff and the radiated power in H-mode plasmas as a result of increases in the carbon and medium-Z metallic impurities. Lithium itself remained at a very low level in the plasma core, <0.1%. Initial results are reported from operation with a Liquid Lithium Divertor (LLD) recently installed.

  19. Regenerable hydrogen storage in lithium amidoborane.

    PubMed

    Tang, Ziwei; Tan, Yingbin; Chen, Xiaowei; Yu, Xuebin

    2012-09-25

    Regenerable hydrogen storage of lithium amidoborane is firstly achieved through the routes of direct thermal dehydrogenation and subsequent chemical hydrogenation of its dehydrogenated products by treatment with hydrazine in liquid ammonia. PMID:22875287

  20. Layered electrodes for lithium cells and batteries

    DOEpatents

    Johnson; Christopher S. , Thackeray; Michael M. , Vaughey; John T. , Kahaian; Arthur J. , Kim; Jeom-Soo

    2008-04-15

    Lithium metal oxide compounds of nominal formula Li.sub.2MO.sub.2, in which M represents two or more positively charged metal ions, selected predominantly and preferably from the first row of transition metals are disclosed herein. The Li.sub.2MO.sub.2 compounds have a layered-type structure, which can be used as positive electrodes for lithium electrochemical cells, or as a precursor for the in-situ electrochemical fabrication of LiMO.sub.2 electrodes. The Li.sub.2MO.sub.2 compounds of the invention may have additional functions in lithium cells, for example, as end-of-discharge indicators, or as negative electrodes for lithium cells.

  1. Lithium ion battery with improved safety

    DOEpatents

    Chen, Chun-hua; Hyung, Yoo Eup; Vissers, Donald R.; Amine, Khalil

    2006-04-11

    A lithium battery with improved safety that utilizes one or more additives in the battery electrolyte solution wherein a lithium salt is dissolved in an organic solvent, which may contain propylene, carbonate. For example, a blend of 2 wt % triphenyl phosphate (TPP), 1 wt % diphenyl monobutyl phosphate (DMP) and 2 wt % vinyl ethylene carbonate additives has been found to significantly enhance the safety and performance of Li-ion batteries using a LiPF6 salt in EC/DEC electrolyte solvent. The invention relates to both the use of individual additives and to blends of additives such as that shown in the above example at concentrations of 1 to 4-wt % in the lithium battery electrolyte. This invention relates to additives that suppress gas evolution in the cell, passivate graphite electrode and protect it from exfoliating in the presence of propylene carbonate solvents in the electrolyte, and retard flames in the lithium batteries.

  2. A Polymer Lithium-Oxygen Battery

    PubMed Central

    Elia, Giuseppe Antonio; Hassoun, Jusef

    2015-01-01

    Herein we report the characteristics of a lithium-oxygen battery using a solid polymer membrane as the electrolyte separator. The polymer electrolyte, fully characterized in terms of electrochemical properties, shows suitable conductivity at room temperature allowing the reversible cycling of the Li-O2 battery with a specific capacity as high as 25,000 mAh gC−1 reflected in a surface capacity of 12.5 mAh cm−2. The electrochemical formation and dissolution of the lithium peroxide during Li-O2 polymer cell operation is investigated by electrochemical techniques combined with X-ray diffraction study, demonstrating the process reversibility. The excellent cell performances in terms of delivered capacity, in addition to its solid configuration allowing the safe use of lithium metal as high capacity anode, demonstrate the suitability of the polymer lithium-oxygen as high-energy storage system. PMID:26238552

  3. Lithium Circuit Test Section Design and Fabrication

    NASA Astrophysics Data System (ADS)

    Godfroy, Thomas; Garber, Anne; Martin, James

    2006-01-01

    The Early Flight Fission - Test Facilities (EFF-TF) team has designed and built an actively pumped lithium flow circuit. Modifications were made to a circuit originally designed for NaK to enable the use of lithium that included application specific instrumentation and hardware. Component scale freeze/thaw tests were conducted to both gain experience with handling and behavior of lithium in solid and liquid form and to supply anchor data for a Generalized Fluid System Simulation Program (GFSSP) model that was modified to include the physics for freeze/thaw transitions. Void formation was investigated. The basic circuit components include: reactor segment, lithium to gas heat exchanger, electromagnetic (EM) liquid metal pump, load/drain reservoir, expansion reservoir, instrumentation, and trace heaters. This paper discusses the overall system design and build and the component testing findings.

  4. Susceptibility of 2 1/4 Cr-1Mo steel to liquid metal induced embrittlement by lithium-lead solutions

    SciTech Connect

    Eberhard, B.A.; Edwards, G.R.

    1984-08-01

    An investigation has been conducted on the liquid metal induced embrittlement susceptibility of 2 1/4Cr-1Mo steel exposed to lithium and 1a/o lead-lithium at temperatures between 190/sup 0/C and 525/sup 0/C. This research was part of an ongoing effort to evaluate the compatibility of liquid lithium solutions with potential fusion reactor containment materials. Of particular interest was the microstructure present in a weld heat-affected zone, a microstructure known to be highly susceptible to corrosive attack by liquid lead-lithium solutions. Embrittlement susceptibility was determined by conducting tension tests on 2 1/4Cr-1Mo steel exposed to an inert environment as well as to a lead-lithium liquid and observing the change in tensile behavior. The 2 1/4Cr-1Mo steel was also given a base plate heat treatment to observe its embrittlement susceptibility to 1a/o lead-lithium. The base plate microstructure was severely embrittled at temperatures less than 500/sup 0/C. Tempering the base plate was effective in restoring adequate ductility to the steel.

  5. Solid state lithium-iodine primary battery

    SciTech Connect

    Sekido, S.; Ninomiya, Y.; Sotomura, T.

    1984-01-10

    A solid-state primary cell comprising a lithium anode, an iodine cathode containing a charge transfer complex and a solid lithium iodide electrolyte doped with a 1-normal-alkyl-pyridinium iodide. The anode surface can be coated with LiOH or Li/sub 3/N. The iodine cathode comprises a complex of iodine and 1-normal-alkyl-pyridinium iodide and preferably contains titanium dioxide powder, alumina gel powder or silica gel powder admixed with the complex.

  6. Lithium in sediments and rocks in Nevada

    USGS Publications Warehouse

    Bohannon, Robert G.; Meier, Allen L.

    1976-01-01

    The purpose of the sampling program was to determine if areas of anonalous lithium could be recognized by reconnaissance surface sampling. The results, however, have been indeterminate because most large lithium deposits occur at depth and appear to be formed when deeply buried. Many may not manifest themselves at the surface at all . Nonetheless, the data derived during the surface sampling program will be presented in this report.

  7. Issues and challenges facing rechargeable lithium batteries.

    PubMed

    Tarascon, J M; Armand, M

    2001-11-15

    Technological improvements in rechargeable solid-state batteries are being driven by an ever-increasing demand for portable electronic devices. Lithium-ion batteries are the systems of choice, offering high energy density, flexible and lightweight design, and longer lifespan than comparable battery technologies. We present a brief historical review of the development of lithium-based rechargeable batteries, highlight ongoing research strategies, and discuss the challenges that remain regarding the synthesis, characterization, electrochemical performance and safety of these systems. PMID:11713543

  8. Design and simulation of lithium rechargeable batteries

    SciTech Connect

    Doyle, C.M.

    1995-08-01

    Lithium -based rechargeable batteries that utilize insertion electrodes are being considered for electric-vehicle applications because of their high energy density and inherent reversibility. General mathematical models are developed that apply to a wide range of lithium-based systems, including the recently commercialized lithium-ion cell. The modeling approach is macroscopic, using porous electrode theory to treat the composite insertion electrodes and concentrated solution theory to describe the transport processes in the solution phase. The insertion process itself is treated with a charge-transfer process at the surface obeying Butler-Volmer kinetics, followed by diffusion of the lithium ion into the host structure. These models are used to explore the phenomena that occur inside of lithium cells under conditions of discharge, charge, and during periods of relaxation. Also, in order to understand the phenomena that limit the high-rate discharge of these systems, we focus on the modeling of a particular system with well-characterized material properties and system parameters. The system chosen is a lithium-ion cell produced by Bellcore in Red Bank, NJ, consisting of a lithium-carbon negative electrode, a plasticized polymer electrolyte, and a lithium-manganese-oxide spinel positive electrode. This battery is being marketed for consumer electronic applications. The system is characterized experimentally in terms of its transport and thermodynamic properties, followed by detailed comparisons of simulation results with experimental discharge curves. Next, the optimization of this system for particular applications is explored based on Ragone plots of the specific energy versus average specific power provided by various designs.

  9. A Cable-Shaped Lithium Sulfur Battery.

    PubMed

    Fang, Xin; Weng, Wei; Ren, Jing; Peng, Huisheng

    2016-01-20

    A carbon nanostructured hybrid fiber is developed by integrating mesoporous carbon and graphene oxide into aligned carbon nanotubes. This hybrid fiber is used as a 1D cathode to fabricate a new cable-shaped lithium-sulfur battery. The fiber cathode exhibits a decent specific capacity and lifespan, which makes the cable-shaped lithium-sulfur battery rank far ahead of other fiber-shaped batteries. PMID:26585740

  10. Polymer Electrolytes for Lithium/Sulfur Batteries

    PubMed Central

    Zhao, Yan; Zhang, Yongguang; Gosselink, Denise; Doan, The Nam Long; Sadhu, Mikhail; Cheang, Ho-Jae; Chen, Pu

    2012-01-01

    This review evaluates the characteristics and advantages of employing polymer electrolytes in lithium/sulfur (Li/S) batteries. The main highlights of this study constitute detailed information on the advanced developments for solid polymer electrolytes and gel polymer electrolytes, used in the lithium/sulfur battery. This includes an in-depth analysis conducted on the preparation and electrochemical characteristics of the Li/S batteries based on these polymer electrolytes. PMID:24958296

  11. Design Evaluation of High Reliability Lithium Batteries

    NASA Technical Reports Server (NTRS)

    Buchman, R. C.; Helgeson, W. D.; Istephanous, N. S.

    1985-01-01

    Within one year, a lithium battery design can be qualified for device use through the application of accelerated discharge testing, calorimetry measurements, real time tests and other supplemental testing. Materials and corrosion testing verify that the battery components remain functional during expected battery life. By combining these various methods, a high reliability lithium battery can be manufactured for applications which require zero defect battery performance.

  12. Sustainability Impact of Nanomaterial Enhanced Lithium Ion Batteries

    NASA Astrophysics Data System (ADS)

    Ganter, Matthew

    Energy storage devices are becoming an integral part of sustainable energy technology adoption, particularly, in alternative transportation (electric vehicles) and renewable energy technologies (solar and wind which are intermittent). The most prevalent technology exhibiting near-term impact are lithium ion batteries, especially in portable consumer electronics and initial electric vehicle models like the Chevy Volt and Nissan Leaf. However, new technologies need to consider the full life-cycle impacts from material production and use phase performance to the end-of-life management (EOL). This dissertation investigates the impacts of nanomaterials in lithium ion batteries throughout the life cycle and develops strategies to improve each step in the process. The embodied energy of laser vaporization synthesis and purification of carbon nanotubes (CNTs) was calculated to determine the environmental impact of the novel nanomaterial at beginning of life. CNTs were integrated into lithium ion battery electrodes as conductive additives, current collectors, and active material supports to increase power, energy, and thermal stability in the use phase. A method was developed to uniformly distribute CNT conductive additives in composites. Cathode composites with CNT additives had significant rate improvements (3x the capacity at a 10C rate) and higher thermal stability (40% reduction in exothermic energy released upon overcharge). Similar trends were also measured with CNTs in anode composites. Advanced free-standing anodes incorporating CNTs with high capacity silicon and germanium were measured to have high capacities where surface area reduction improved coulombic efficiencies and thermal stability. A thermal stability plot was developed that compares the safety of traditional composites with free-standing electrodes, relating the results to thermal conductivity and surface area effects. The EOL management of nanomaterials in lithium ion batteries was studied and a novel

  13. Glass for sealing lithium cells

    DOEpatents

    Leedecke, C.J.

    1981-08-28

    Glass compositions resistant to corrosion by lithium cell electrolyte and having an expansion coefficient of 45 to 85 x 10/sup -70/C/sup -1/ have been made with SiO/sub 2/, 25 to 55% by weight; B/sub 2/O/sub 3/, 5 to 12%; Al/sub 2/O/sub 3/, 12 to 35%; CaO, 5 to 15%; MgO, 5 to 15%; SrO, 0 to 10%; and La/sub 2/O/sub 3/, 0 to 5%. Preferred compositions within that range contain 3 to 8% SrO and 0.5 to 2.5% La/sub 2/O/sub 3/.

  14. The cosmological lithium problem revisited

    NASA Astrophysics Data System (ADS)

    Bertulani, C. A.; Mukhamedzhanov, A. M.; Shubhchintak

    2016-07-01

    After a brief review of the cosmological lithium problem, we report a few recent attempts to find theoretical solutions by our group at Texas A&M University (Commerce & College Station). We will discuss our studies on the theoretical description of electron screening, the possible existence of parallel universes of dark matter, and the use of non-extensive statistics during the Big Bang nucleosynthesis epoch. Last but not least, we discuss possible solutions within nuclear physics realm. The impact of recent measurements of relevant nuclear reaction cross sections for the Big Bang nucleosynthesis based on indirect methods is also assessed. Although our attempts may not able to explain the observed discrepancies between theory and observations, they suggest theoretical developments that can be useful also for stellar nucleosynthesis.

  15. Magnesium-lithium casting alloys

    NASA Technical Reports Server (NTRS)

    Latenko, V. P.; Silchenko, T. V.; Tikhonov, V. A.; Maltsev, V. P.; Korablin, V. P.

    1974-01-01

    The strength properties of magnesium-lithium alloys at room, low, and high temperatures are investigated. It is found that the alloys may have practical application at ambient temperatures up to 100 C, that negative temperatures have a favorable influence on the alloy strength, and that cyclic temperature variations have practically no effect on the strength characteristics. The influence of chemical coatings on corrosion resistance of the MgLi alloys is examined. Several facilities based on pressure casting machines, low-pressure casting machines, and magnetodynamic pumps were designed for producing MgLi alloy castings. Results were obtained for MgLi alloys reinforced with fibers having a volumetric content of 15%.

  16. Predissociation dynamics of lithium iodide

    SciTech Connect

    Schmidt, H.; Vangerow, J. von; Stienkemeier, F.; Mudrich, M.; Bogomolov, A. S.; Baklanov, A. V.; Reich, D. M.; Skomorowski, W.; Koch, C. P.

    2015-01-28

    The predissociation dynamics of lithium iodide (LiI) in the first excited A-state is investigated for molecules in the gas phase and embedded in helium nanodroplets, using femtosecond pump-probe photoionization spectroscopy. In the gas phase, the transient Li{sup +} and LiI{sup +} ion signals feature damped oscillations due to the excitation and decay of a vibrational wave packet. Based on high-level ab initio calculations of the electronic structure of LiI and simulations of the wave packet dynamics, the exponential signal decay is found to result from predissociation predominantly at the lowest avoided X-A potential curve crossing, for which we infer a coupling constant V{sub XA} = 650(20) cm{sup −1}. The lack of a pump-probe delay dependence for the case of LiI embedded in helium nanodroplets indicates fast droplet-induced relaxation of the vibrational excitation.

  17. Electrode for a lithium cell

    DOEpatents

    Thackeray, Michael M.; Vaughey, John T.; Dees, Dennis W.

    2008-10-14

    This invention relates to a positive electrode for an electrochemical cell or battery, and to an electrochemical cell or battery; the invention relates more specifically to a positive electrode for a non-aqueous lithium cell or battery when the electrode is used therein. The positive electrode includes a composite metal oxide containing AgV.sub.3O.sub.8 as one component and one or more other components consisting of LiV.sub.3O.sub.8, Ag.sub.2V.sub.4O.sub.11, MnO.sub.2, CF.sub.x, AgF or Ag.sub.2O to increase the energy density of the cell, optionally in the presence of silver powder and/or silver foil to assist in current collection at the electrode and to improve the power capability of the cell or battery.

  18. Rechargeable lithium-ion cell

    DOEpatents

    Bechtold, Dieter; Bartke, Dietrich; Kramer, Peter; Kretzschmar, Reiner; Vollbert, Jurgen

    1999-01-01

    The invention relates to a rechargeable lithium-ion cell, a method for its manufacture, and its application. The cell is distinguished by the fact that it has a metallic housing (21) which is electrically insulated internally by two half shells (15), which cover electrode plates (8) and main output tabs (7) and are composed of a non-conductive material, where the metallic housing is electrically insulated externally by means of an insulation coating. The cell also has a bursting membrane (4) which, in its normal position, is located above the electrolyte level of the cell (1). In addition, the cell has a twisting protection (6) which extends over the entire surface of the cover (2) and provides centering and assembly functions for the electrode package, which comprises the electrode plates (8).

  19. Predictors of Lithium Response in Bipolar Disorder

    PubMed Central

    Tighe, Sarah K.; Mahon, Pamela B.; Potash, James B.

    2011-01-01

    While lithium is generally regarded as the first-line agent for patients with bipolar disorder, it does not work for everyone, which raises the question: can we predict who will be most likely to respond? In this paper, we review the most compelling clinical, biologic, and genetic predictors of lithium response in bipolar disorder. Among clinical factors, the strongest predictors of good response are fewer hospitalizations preceding treatment, an episodic course characterized by an illness pattern of mania followed by depression, and a later age at onset of bipolar disorder. While several biologic predictors have been studied, the results are preliminary and require replication with studies of larger patient samples over longer observation periods. Neuroimaging is a particularly promising method given that it might concurrently illuminate pathophysiologic underpinnings of bipolar disorder, the mechanism of action of lithium, and potential predictors of lithium response. The first genome-wide association study of lithium response was recently completed. No definitive results emerged, perhaps because the study was underpowered. With major new initiatives in progress aiming to identify genes and genetic variations associated with lithium response, there is much reason to be hopeful that clinically useful information might be generated within the next several years. This could ultimately translate into tests that could guide the choice of mood-stabilizing medication for patients. In addition, it might facilitate pharmacologic research aimed at developing newer, more effective medications that might act more quickly and yield fewer side effects. PMID:23251751

  20. Lithium pinacolone enolate solvated by hexamethylphosphoramide.

    PubMed

    Guang, Jie; Liu, Qiyong Peter; Hopson, Russell; Williard, Paul G

    2015-06-17

    We report the crystal structure of a substoichiometric, HMPA-trisolvated lithium pinacolone enolate tetramer (LiOPin)4·HMPA3 abbreviated as T3. In this tetramer one HMPA binds to lithium more strongly than the other two causing a reduction in spatial symmetry with corresponding loss of C3 symmetry. A variety of NMR experiments, including HMPA titration, diffusion coefficient-formula weight (D-FW) analysis, and other multinuclear one- and two-dimensional NMR techniques reveal that T3 is the major species in hydrocarbon solution when more than 0.6 equiv of HMPA is present. Due to a small amount of moisture from HMPA or air leaking into the solution, a minor complex was identified and confirmed by X-ray diffraction analysis as a mixed aggregate containing enolate, lithium hydroxide, and HMPA in a 4:2:4 ratio, [(LiOPin)4·(LiOH)2·HMPA4], that we refer to as pseudo-T4. A tetra-HMPA-solvated lithium cyclopentanone enolate tetramer was also prepared and characterized by X-ray diffraction, leading to the conclusion that steric effects dominate the formation and solvation of the pinacolone aggregates. An unusual mixed aggregate consisting of pinacolone enolate, lithium diisopropyl amide, lithium oxide, and HMPA in the ratio 5:1:1:2 is also described. PMID:25933508

  1. Lithium brines: A global perspective: Chapter 14

    USGS Publications Warehouse

    Munk, LeeAnn; Hynek, Scott; Bradley, Dwight C.; Boutt, David; Labay, Keith A.; Jochens, Hillary

    2016-01-01

    Lithium is a critical and technologically important element that has widespread use, particularly in batteries for hybrid cars and portable electronic devices. Global demand for lithium has been on the rise since the mid-1900s and is projected to continue to increase. Lithium is found in three main deposit types: (1) pegmatites, (2) continental brines, and (3) hydrothermally altered clays. Continental brines provide approximately three-fourths of the world’s Li production due to their relatively low production cost. The Li-rich brine systems addressed here share six common characteristics that provide clues to deposit genesis while also serving as exploration guidelines. These are as follows: (1) arid climate; (2) closed basin containing a salar (salt crust), a salt lake, or both; (3) associated igneous and/or geothermal activity; (4) tectonically driven subsidence; (5) suitable lithium sources; and (6) sufficient time to concentrate brine. Two detailed case studies of Li-rich brines are presented; one on the longest produced lithium brine at Clayton Valley, Nevada, and the other on the world’s largest producing lithium brine at the Salar de Atacama, Chile.

  2. Rechargeable Thin-film Lithium Batteries

    DOE R&D Accomplishments Database

    Bates, J. B.; Gruzalski, G. R.; Dudney, N. J.; Luck, C. F.; Yu, Xiaohua

    1993-08-01

    Rechargeable thin film batteries consisting of lithium metal anodes, an amorphous inorganic electrolyte, and cathodes of lithium intercalation compounds have recently been developed. The batteries, which are typically less than 6 {mu}m thick, can be fabricated to any specified size, large or small, onto a variety of substrates including ceramics, semiconductors, and plastics. The cells that have been investigated include Li TiS{sub 2}, Li V{sub 2}O{sub 5}, and Li Li{sub x}Mn{sub 2}O{sub 4}, with open circuit voltages at full charge of about 2.5, 3.6, and 4.2, respectively. The development of these batteries would not have been possible without the discovery of a new thin film lithium electrolyte, lithium phosphorus oxynitride, that is stable in contact with metallic lithium at these potentials. Deposited by rf magnetron sputtering of Li{sub 3}PO{sub 4} in N{sub 2}, this material has a typical composition of Li{sub 2.9}PO{sub 3.3}N{sub 0.46} and a conductivity at 25{degrees}C of 2 {mu}S/cm. The maximum practical current density obtained from the thin film cells is limited to about 100 {mu}A/cm{sup 2} due to a low diffusivity of Li{sup +} ions in the cathodes. In this work, the authors present a short review of their work on rechargeable thin film lithium batteries.

  3. Modified lithium borohydrides for reversible hydrogen storage.

    PubMed

    Au, Ming; Jurgensen, Arthur

    2006-04-01

    In an attempt to develop lithium borohydrides as reversible hydrogen storage materials with high hydrogen storage capacities, the feasibility of reducing the dehydrogenation temperature of the lithium borohydride and moderating rehydrogenation conditions was explored. The lithium borohydride was modified by ball milling with metal oxides and metal chlorides as additives. The modified lithium borohydrides released 9 wt % hydrogen starting from 473 K. The dehydrided modified lithium borohydrides absorbed 7-9 wt % hydrogen at 873 K and 7 MPa. The modification with additives reduced the dehydriding starting temperature from 673 to 473 K and moderated the rehydrogenation conditions from 923 K/15 MPa to 873 K/7 MPa. XRD and SEM analysis revealed the formation of an intermediate compound that might play a key role in changing the reaction path, resulting in the lower dehydriding temperature and reversibility. The reversible hydrogen storage capacity of the oxide-modified lithium borohydrides decreased gradually during hydriding/dehydriding cycling. One of the possible reasons for this effect might be the loss of boron during dehydrogenation, but this can be prevented by changing the dehydriding path using appropriate additives. The additives reduced the dehydriding temperature and improved the reversibility, but they also reduced the hydrogen storage capacity. The best compromise can be reached by selecting appropriate additives, optimizing the additive loading, and using new synthesis processes other than ball milling. PMID:16571023

  4. Lithium in the McDermitt caldera, Nevada and Oregon

    USGS Publications Warehouse

    Glanzman, R.K.; McCarthy, J.H., Jr.; Rytuba, J.J.

    1978-01-01

    Anomalously high concentrations of lithium in fluviatile-lacustrine sediments near McDermitt, Nevada, may constitute a potential resource. These sediments are associated with a caldera about 45 km in diameter that is a result of volcanic activity, subsidence and sedimentation chiefly of Miocene age. The sediments originally were vitroclastic and now consist chiefly of authigenic zeolites, clay minerals, feldspar and quartz. Calcite occurs as thin beds, nodules and cement Gypsum is presnt but sparse. Most of the clay beds in the caldera contain 0.01-0.1% Li and have well above the average Li concentration for continental clays (0.006%) (Ronov et al.1). Individual smectitic clay samples from the western and southern part of the caldera contain as much as 0.65% Li and are associated with analcime and K-feldspar. Two beds, each 0.6m thick, contain 0.35% Li. Clay samples from the northern part of the caldera contain as much as 0.36% Li, and are associated with clinoptilolite and erionite. The clay beds are thinner in the north; in one section a bed 0.3 m thick contains 0.36% Li, and in another section a bed 0.1 m thick contains 0.30% Li. Lithium is probably derived from volcanic material and then incorporated into the clay beds during alteration. ?? 1978.

  5. Kinetics of aluminum lithium alloys

    NASA Astrophysics Data System (ADS)

    Pletcher, Ben A.

    2009-12-01

    Aluminum lithium alloys are increasingly used in aerospace for their high strength-to-weight ratio. Additions of lithium, up to 4.2 wt% decrease the alloy density while increasing the modulus and yield strength. The metastable, second phase Al3Li or delta' is intriguing, as it remains spherical and coherent with the matrix phase, alpha, well into the overaged condition. Small interfacial strain energy allows these precipitates to remain spherical for volume fractions (VV ) of delta' less than 0.3, making this alloy system ideal for investigation of late-stage coarsening phenomena. Experimental characterization of three binary Al-Li alloys are presented as a critical test of diffusion screening theory and multi-particle diffusion simulations. Quantitative transmission electron microscopy is used to image the precipitates directly using the centered dark-field technique. Images are analyzed autonomously within a novel Matlab function that determines the center and size of each precipitate. Particle size distribution, particle growth kinetics, and maximum particle size are used to track the precipitate growth and correlate with the predictions of screening theory and multi-particle diffusion simulations. This project is the first extensive study of Al-Li alloys, in over 25 years, applying modern transmission electron microscopy and image analysis techniques. Previous studies sampled but a single alloy composition, and measured far fewer precipitates. This study investigates 3 alloys with volume fractions of the delta precipitates, VV =0.1-0.27, aged at 225C for 1 to 10 days. More than 1000 precipitates were sampled per aging time, creating more statistically significant data. Experimental results are used to test the predictions based on diffusion screening theory and multi-particle aging simulations. (Full text of this dissertation may be available via the University of Florida Libraries web site. Please check http://www.uflib.ufl.edu/etd.html)

  6. The Lithium Isotopic Signature of Hawaiian Basalts

    NASA Astrophysics Data System (ADS)

    Harrison, L.; Weis, D.; Hanano, D. W.

    2013-12-01

    Recycling of oceanic crust and sediment is a common mechanism to account for the presence of chemical heterogeneities observed in oceanic island basalts (OIBs). On Hawai';i, a mantle plume-sourced OIB with a high mass flux, sampling of deep mantle heterogeneities accounts for the presence of two unique geochemical and geographical trends called the Loa and Kea trends. The Loa trend overlaps the Pacific large low shear velocity province and is distinctly more enriched [1] than the Kea trend with average Pacific mantle compositions [2]. Because of the sizeable fractionation of lithium isotopes in low temperature environments, lithium serves as a tracer for the presence of recycled material in OIB sources, including Hawai'i. In this study, we analyzed 87 samples of Hawaiian basalt from the pre-shield, shield, post-shield, and rejuvenated volcanic stages and 10 samples of altered oceanic crust from ODP Site 843 for lithium isotopes using a multi-collector inductively coupled plasma mass spectrometer. Correlations of lithium isotopes with the radiogenic isotopes Pb, Hf, Nd, and Sr indicate lithium isotopes may be used to trace components in mantle plumes such as Hawai';i. The measured range of lithium isotopes for shield stage lavas is δ7Li = 1.8 - 5.7‰ and for post-shield lavas is δ7Li = 0.8 - 4.7‰. Pre-shield stage lavas (Lo'ihi volcano only) and rejuvenated lavas are the least and most homogeneous volcanic stages, respectively, in lithium isotopes. The Loa and Kea geochemical trends have different lithium isotopic signatures, with Loa trend shield volcanoes exhibiting lighter lithium isotopic signatures (δ7Li = 3.5‰ [N=43]) than Kea trend shield volcanoes (δ7Li = 4.0‰ [N=31]) [3]. Similarly, post-shield lavas have systematically lighter δ7Li than shield lavas. The presence of systematic differences in lithium isotopic signatures may indicate: 1) the sampling of distinct components in the deep source, to account for variations between Kea and Loa trend

  7. Selective Recovery of Lithium from Cathode Materials of Spent Lithium Ion Battery

    NASA Astrophysics Data System (ADS)

    Higuchi, Akitoshi; Ankei, Naoki; Nishihama, Syouhei; Yoshizuka, Kazuharu

    2016-07-01

    Selective recovery of lithium from four kinds of cathode materials, manganese-type, cobalt-type, nickel-type, and ternary-type, of spent lithium ion battery was investigated. In all cathode materials, leaching of lithium was improved by adding sodium persulfate (Na2S2O8) as an oxidant in the leaching solution, while the leaching of other metal ions (manganese, cobalt, and nickel) was significantly suppressed. Optimum leaching conditions, such as pH, temperature, amount of Na2S2O8, and solid/liquid ratio, for the selective leaching of lithium were determined for all cathode materials. Recovery of lithium from the leachate as lithium carbonate (Li2CO3) was then successfully achieved by adding sodium carbonate (Na2CO3) to the leachate. Optimum recovery conditions, such as pH, temperature, and amount of Na2CO3, for the recovery of lithium as Li2CO3 were determined for all cases. Purification of Li2CO3 was achieved by lixiviation in all systems, with purities of the Li2CO3 higher than 99.4%, which is almost satisfactory for the battery-grade purity of lithium.

  8. Magnesium oxide doping reduces acoustic wave attenuation in lithium metatantalate and lithium metaniobate crystals

    NASA Technical Reports Server (NTRS)

    Croft, W.; Damon, R.; Kedzie, R.; Kestigian, M.; Smith, A.; Worley, J.

    1970-01-01

    Single crystals of lithium metatantalate and lithium metaniobate, grown from melts having different stoichiometries and different amounts of magnesium oxide, show that doping lowers temperature-independent portion of attenuation of acoustic waves. Doped crystals possess optical properties well suited for electro-optical and photoelastic applications.

  9. Growth of Lithium Lanthanum Titanate Nanosheets and Their Application in Lithium-Ion Batteries.

    PubMed

    Lin, Xi; Wang, Hongqiang; Du, Haiwei; Xiong, Xinrun; Qu, Bo; Guo, Zaiping; Chu, Dewei

    2016-01-20

    In this work, lithium-doped lanthanum titanate (LLTO) nanosheets have been prepared by a facile hydrothermal approach. It is found that with the incorporation of lithium ions, the morphology of the product transfers from rectangular nanosheets to irregular nanosheets along with a transition from La2Ti2O7 to Li0.5La0.5TiO3. The as-prepared LLTO nanosheets are used to enhance electrochemical performance of the LiCo1/3Ni1/3Mn1/3O2 (CNM) electrode by forming a higher lithium-ion conductive network. The LiCo1/3Ni1/3Mn1/3O2-Li0.5La0.5TiO3 (CNM-LLTO) electrode shows better a lithium diffusion coefficient of 1.5 × 10(-15) cm(2) s(-1), resulting from higher lithium-ion conductivity of LLTO and shorter lithium diffusion path, compared with the lithium diffusion coefficient of CNM electrode (5.44 × 10(-16) cm(2) s(-1)). Superior reversibility and stability are also found in the CNM-LLTO electrode, which retains a capacity at 198 mAh/g after 100 cycles at a rate of 0.1 C. Therefore, it can be confirmed that the existence of LLTO nanosheets can act as bridges to facilitate the lithium-ion diffusion between the active materials and electrolytes. PMID:26697735

  10. Rechargeable lithium sulfide electrode for a polymer tin/sulfur lithium-ion battery

    NASA Astrophysics Data System (ADS)

    Hassoun, Jusef; Sun, Yang-Kook; Scrosati, Bruno

    In this work we investigate the electrochemical behavior of a new type of carbon-lithium sulfide composite electrode. Results based on cyclic voltammetry, charge (lithium removal)-discharge (lithium acceptance) demonstrate that this electrode has a good performance in terms of reversibility, cycle life and coulombic efficiency. XRD analysis performed in situ in a lithium cell shows that lithium sulfide can be converted into sulfur during charge and re-converted back into sulfide during the following discharge process. We also show that this electrochemical process can be efficiently carried out in polymer electrolyte lithium cells and thus, that the Li 2S-C composite can be successfully used as cathode for the development of novel types of rechargeable lithium-ion sulfur batteries where the reactive and unsafe lithium metal anode is replaced by a reliable, high capacity tin-carbon composite and the unstable organic electrolyte solution is replaced by a composite gel polymer membrane that is safe, highly conductive and able to control dendrite growth across the cell. This new Sn-C/Li 2S polymer battery operates with a capacity of 600 mAh g -1 and with an average voltage of 2 V, this leading to a value of energy density amounting to 1200 Wh kg -1.

  11. Transport of beryllium-7 in a lithium loop

    SciTech Connect

    Katsuta, H.; Anantatmula, R.P.; Bechtold, R.A.; Brehm, W.F.

    1984-07-01

    A /sup 7/Be transport test was performed in the Beryllium-7 Experimental Lithium Loop with hot leg at 270/sup 0/C and cold leg at 230/sup 0/C. The ''cold leg'' test stringer was in a rising temperature region at 250/sup 0/C. A total of 108 test coupons were included in the material compatibility and deposition test programs, containing AISI Types 304 and 304L stainless steels, Fe-2 1/4 Cr1 MO, pure iron, molybdenum, beryllium, zirconium, titanium, yttrium, three different aluminide coatings on Type 304 stainless steel substrates, and both tubular and flat butt-welds of Type 304 stainless steel. An average lithium velocity of 1.36 m/s was established during the test which was terminated after 3718 h. The /sup 7/Be activity data indicated that the deposition of /sup 7/Be is a function of temperature. The cold leg positions displayed maximum /sup 7/Be deposition followed by the intermediate temperature locations (cold leg test stringer) and the hot leg locations. Two chemical forms of /sup 7/Be are expected in lithium, namely, unbonded /sup 7/Be at a low concentration, and a fine precipitate of /sup 7/Be/sub 3/N/sub 2/ at a high concentration. The deposit in the hot leg region is presumed to be primarily /sup 7/Be, while the cold leg deposit is mostly /sup 7/Be/sub 3/N/sub 2/. The cold leg specimens of a given material showed more /sup 7/Be deposition than the hot leg specimens of the same material, consistent with the /sup 7/Be activity data on the piping. Based on the present investigations and previous data, it is concluded that /sup 7/Be produced in the Fusion Materials Irradiation Test (FMIT) facility will have sufficient nitrogen in the lithium system to form /sup 7/Be/sub 3/N/sub 2/. It is expected that the majority of /sup 7/Be will be transported to the colder parts of the loop and deposited as /sup 7/Be/sub 3/N/sub 2/. However, a small amount of /sup 7/Be in the unbonded form will be in the hotter parts of the loop and is expected to diffuse into the steel

  12. Effect of cobalt incorporation and lithium enrichment in lithium nickel manganese oxides.

    SciTech Connect

    Deng, H.; Belharouak, I.; Wu, H.; Dambournet, D.; Amine, K.

    2010-05-10

    Candidate cathode materials of cobalt-incorporated and lithium-enriched Li{sub (1+x)}Ni{sub 0.25}Co{sub 0.15}Mn{sub 0.6}O{sub (2.175+x/2)} (x=0.225-0.65) have been prepared by a coprecipitation method and a solid-state reaction. We systematically investigated the effect of both cobalt presence and lithium concentration on the structure, physical properties, and electrochemical behavior of the studied samples. The electrochemical performance of the cobalt-containing compounds showed much less dependence on the variation in the lithium amounts compared to the cobalt-free counterpart. The study demonstrated that even with cobalt incorporation, proper lithium content is the key to desirable cathode materials with nanostructured primary particles that are indispensable to achieve high capacity and high rate capability and, therefore, both improved energy and power densities for lithium-ion batteries.

  13. High-capacity electrode materials for rechargeable lithium batteries: Li3NbO4-based system with cation-disordered rocksalt structure

    PubMed Central

    Yabuuchi, Naoaki; Takeuchi, Mitsue; Nakayama, Masanobu; Shiiba, Hiromasa; Ogawa, Masahiro; Nakayama, Keisuke; Ohta, Toshiaki; Endo, Daisuke; Ozaki, Tetsuya; Inamasu, Tokuo; Sato, Kei; Komaba, Shinichi

    2015-01-01

    Rechargeable lithium batteries have rapidly risen to prominence as fundamental devices for green and sustainable energy development. Lithium batteries are now used as power sources for electric vehicles. However, materials innovations are still needed to satisfy the growing demand for increasing energy density of lithium batteries. In the past decade, lithium-excess compounds, Li2MeO3 (Me = Mn4+, Ru4+, etc.), have been extensively studied as high-capacity positive electrode materials. Although the origin as the high reversible capacity has been a debatable subject for a long time, recently it has been confirmed that charge compensation is partly achieved by solid-state redox of nonmetal anions (i.e., oxide ions), coupled with solid-state redox of transition metals, which is the basic theory used for classic lithium insertion materials, such as LiMeO2 (Me = Co3+, Ni3+, etc.). Herein, as a compound with further excess lithium contents, a cation-ordered rocksalt phase with lithium and pentavalent niobium ions, Li3NbO4, is first examined as the host structure of a new series of high-capacity positive electrode materials for rechargeable lithium batteries. Approximately 300 mAh⋅g−1 of high-reversible capacity at 50 °C is experimentally observed, which partly originates from charge compensation by solid-state redox of oxide ions. It is proposed that such a charge compensation process by oxide ions is effectively stabilized by the presence of electrochemically inactive niobium ions. These results will contribute to the development of a new class of high-capacity electrode materials, potentially with further lithium enrichment (and fewer transition metals) in the close-packed framework structure with oxide ions. PMID:26056288

  14. High-capacity electrode materials for rechargeable lithium batteries: Li3NbO4-based system with cation-disordered rocksalt structure.

    PubMed

    Yabuuchi, Naoaki; Takeuchi, Mitsue; Nakayama, Masanobu; Shiiba, Hiromasa; Ogawa, Masahiro; Nakayama, Keisuke; Ohta, Toshiaki; Endo, Daisuke; Ozaki, Tetsuya; Inamasu, Tokuo; Sato, Kei; Komaba, Shinichi

    2015-06-23

    Rechargeable lithium batteries have rapidly risen to prominence as fundamental devices for green and sustainable energy development. Lithium batteries are now used as power sources for electric vehicles. However, materials innovations are still needed to satisfy the growing demand for increasing energy density of lithium batteries. In the past decade, lithium-excess compounds, Li2MeO3 (Me = Mn(4+), Ru(4+), etc.), have been extensively studied as high-capacity positive electrode materials. Although the origin as the high reversible capacity has been a debatable subject for a long time, recently it has been confirmed that charge compensation is partly achieved by solid-state redox of nonmetal anions (i.e., oxide ions), coupled with solid-state redox of transition metals, which is the basic theory used for classic lithium insertion materials, such as LiMeO2 (Me = Co(3+), Ni(3+), etc.). Herein, as a compound with further excess lithium contents, a cation-ordered rocksalt phase with lithium and pentavalent niobium ions, Li3NbO4, is first examined as the host structure of a new series of high-capacity positive electrode materials for rechargeable lithium batteries. Approximately 300 mAh ⋅ g(-1) of high-reversible capacity at 50 °C is experimentally observed, which partly originates from charge compensation by solid-state redox of oxide ions. It is proposed that such a charge compensation process by oxide ions is effectively stabilized by the presence of electrochemically inactive niobium ions. These results will contribute to the development of a new class of high-capacity electrode materials, potentially with further lithium enrichment (and fewer transition metals) in the close-packed framework structure with oxide ions. PMID:26056288

  15. Lithium and strontium isotopic systematics in playas in Nevada, USA: constraints on the origin of lithium

    NASA Astrophysics Data System (ADS)

    Araoka, Daisuke; Kawahata, Hodaka; Takagi, Tetsuichi; Watanabe, Yasushi; Nishimura, Koshi; Nishio, Yoshiro

    2014-03-01

    Lithium-rich brine in playas is a major raw material for lithium production. Recently, lithium isotopic ratios (δ7Li) have been identified as a tool for investigating water-rock interactions. Thus, to constrain the origin of lithium in playas by the use of its isotopes, we conducted leaching experiments on various lacustrine sediment and evaporite deposit samples collected from playas in Nevada, USA. We determined lithium and strontium isotopic ratios and contents and trace element contents of the leachate, estimated the initial δ7Li values in the water flowing into the playas, and examined the origin of lithium in playas by comparison with δ7Li values of the possible sources. In samples from the playas, δ7Li values show some variation, reflecting differences both in isotopic fractionation during mineral formation and in initial δ7Li value in water flowing into each playa. However, all δ7Li values in this study are much lower than those in river water and groundwater samples from around the world, but they are close to those of volcanic rocks. Considering the temperature dependence of lithium isotopic fractionation between solid and fluid, these results indicate that the lithium concentrated in playas in Nevada was supplied mainly through high-temperature water-rock interaction associated with local hydrothermal activity and not directly by low-temperature weathering of surface materials. This study, which is the first to report lithium isotopic compositions in playas, demonstrates that δ7Li may be a useful tracer for determining the origin of lithium and evaluating its accumulation processes in playas.

  16. Research proposal for development of an electron stripper using a thin liquid lithium film for rare isotope accelerator.

    SciTech Connect

    Momozaki, Y.; Nuclear Engineering Division

    2006-03-06

    Hydrodynamic instability phenomena in a thin liquid lithium film, which has been proposed for the first stripper in the driver linac of Rare Isotope Accelerator (RIA), were discussed. Since it was considered that film instability could significantly impair the feasibility of the liquid lithium film stripper concept, potential issues and research tasks in the RIA project due to these instability phenomena were raised. In order to investigate these instability phenomena, a research proposal plan was developed. In the theoretical part of this research proposal, a use of the linear stability theory was suggested. In the experimental part, it was pointed out that the concept of Reynolds number and Weber number scaling may allow conducting a preliminary experiment using inert simulants, hence reducing technical difficulty, complexity, and cost of the experiments. After confirming the thin film formation in the preliminary experiment using simulants, demonstration experiments using liquid lithium were proposed.

  17. Lithium Resources for the 21st Century

    NASA Astrophysics Data System (ADS)

    Kesler, S.; Gruber, P.; Medina, P.; Keolian, G.; Everson, M. P.; Wallington, T.

    2011-12-01

    Lithium is an important industrial compound and the principal component of high energy-density batteries. Because it is the lightest solid element, these batteries are widely used in consumer electronics and are expected to be the basis for battery electric vehicles (BEVs), hybrid electric vehicles (HEVs) and plug-in hybrid electric vehicles (PHEVs) for the 21st century. In view of the large incremental demand for lithium that will result from expanded use of various types of EVs, long-term estimates of lithium demand and supply are advisable. For GDP growth rates of 2 to 3% and battery recycling rates of 90 to 100%, total demand for lithium for all markets is expected to be a maximum of 19.6 million tonnes through 2100. This includes 3.2 million tonnes for industrial compounds, 3.6 million tonnes for consumer electronics, and 12.8 million tonnes for EVs. Lithium-bearing mineral deposits that might supply this demand contain an estimated resource of approximately 39 million tonnes, although many of these deposits have not been adequately evaluated. These lithium-bearing mineral deposits are of two main types, non-marine playa-brine deposits and igneous deposits. Playa-brine deposits have the greatest immediate resource potential (estimated at 66% of global resources) and include the Salar de Atacama (Chile), the source of almost half of current world lithium production, as well as Zabuye (China/Tibet) and Hombre Muerto (Argentina). Additional important playa-brine lithium resources include Rincon (Argentina), Qaidam (China), Silver Peak (USA) and Uyuni (Bolivia), which together account for about 35% of the estimated global lithium resource. Information on the size and continuity of brine-bearing aquifers in many of these deposits is limited, and differences in chemical composition of brines from deposit to deposit require different extraction processes and yield different product mixes of lithium, boron, potassium and other elements. Numerous other brines in playas

  18. Transient shear flow of model lithium lubricating greases

    NASA Astrophysics Data System (ADS)

    Delgado, M. A.; Franco, J. M.; Valencia, C.; Kuhn, E.; Gallegos, C.

    2009-03-01

    This paper deals with the analysis of the transient shear flow behavior of lithium lubricating greases differing in soap concentration and base oil viscosity. The shear-induced evolution of grease microstructure has been studied by means of stress-growth experiments. With this aim, different lubricating grease formulations were manufactured by modifying the concentration of lithium 12-hydroxystearate and the viscosity of the base oil, according to a RSM statistical design. Moreover, atomic force microscopy (AFM) observations were carried out. The transient stress response can be successfully described by the generalized Leider-Bird model based on two exponential terms. Different rheological parameters, related to both the elastic response and the structural breakdown of greases, have been analysed. In this sense, it has been found that the elastic properties of lithium lubricating greases were highly influenced by soap concentration and oil viscosity. The stress overshoot, τ max , depends linearly on both variables in the whole shear rate range studied, although the effect of base oil viscosity on this parameter is opposite at low and high shear rates. Special attention has been given to the first part of the stress-growth curve. In this sense, it can be deduced that the “yielding” energy density not only depends on grease composition, but also on shear rate. Moreover, an interesting asymptotic tendency has been found for both the “yielding” energy density and the stress overshoot by increasing shear rate. The asymptotic values of these parameters have been correlated to the friction coefficient obtained in a ball-disc tribometer.

  19. Lithium-ion batteries having conformal solid electrolyte layers

    SciTech Connect

    Kim, Gi-Heon; Jung, Yoon Seok

    2014-05-27

    Hybrid solid-liquid electrolyte lithium-ion battery devices are disclosed. Certain devices comprise anodes and cathodes conformally coated with an electron insulating and lithium ion conductive solid electrolyte layer.

  20. Aftereffects of Lithium-Conditioned Stimuli on Consummatory Behavior

    ERIC Educational Resources Information Center

    Domjan, Michael; Gillan, Douglas J.

    1977-01-01

    To complement investigations of the direct effects of lithium toxicosis on consummatory behavior, these experiments were designed to determine the aftereffects on drinking of exposure to a conditioned stimulus previously paired with lithium. (Author/RK)

  1. Magnesium-lithium alloys developed for low temperature use

    NASA Technical Reports Server (NTRS)

    Dunkerley, F. J.; Leavenworth, H. W., Jr.

    1967-01-01

    Three new magnesium-lithium alloys have been developed for application at cryogenic temperatures. These lightweight alloys have approximately doubled the tensile and yield strengths at room temperature of previously described magnesium-lithium alloys.

  2. Improved Fabrication of Lithium Films Having Micron Features

    NASA Technical Reports Server (NTRS)

    Whitacre, Jay

    2006-01-01

    An improved method has been devised for fabricating micron-dimension Li features. This approach is intended for application in the fabrication of lithium-based microelectrochemical devices -- particularly solid-state thin-film lithium microbatteries.

  3. Chemical and morphological characteristics of lithium electrode surfaces

    NASA Technical Reports Server (NTRS)

    Yen, S. P. S.; Shen, D.; Vasquez, R. P.; Grunthaner, F. J.; Somoano, R. B.

    1981-01-01

    Lithium electrode surfaces were analyzed for chemical and morphological characteristics, using electron spectroscopy chemical analysis (ESCA) and scanning electron microscopy (SEM). Samples included lithium metal and lithium electrodes which were cycled in a 1.5 M lithium arsenic hexafluoride/two-methyl tetrahydrofuran electrolyte. Results show that the surface of the as-received lithium metal was already covered by a film composed of LiO2 and an Li2O/CO2 adduct with a thickness of approximately 100-200 A. No evidence of Ni3 was found. Upon exposure of the lithium electrode to a 1.5 M LiAsF6/2-Me-THF electrochemical environment, a second film was observed to form on the surface, consisting primarily of As, Si, and F, possibly in the form of lithium arsenic oxyfluorides or lithium fluorosilicates. It is suggested that the film formation may be attributed to salt degradation.

  4. 78 FR 1119 - Hazardous Materials: Transportation of Lithium Batteries

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-01-07

    ... Materials: Transportation of Lithium Batteries AGENCY: Pipeline and Hazardous Materials Safety... Hazardous Materials Regulations (HMR) on the transportation of lithium cells and batteries, including.... 78, No. 4 / Monday, January 7, 2013 / Proposed Rules#0;#0; ] DEPARTMENT OF TRANSPORTATION...

  5. Lithium isotope fractionation during uptake by gibbsite

    NASA Astrophysics Data System (ADS)

    Wimpenny, Josh; Colla, Christopher A.; Yu, Ping; Yin, Qing-Zhu; Rustad, James R.; Casey, William H.

    2015-11-01

    The intercalation of lithium from solution into the six-membered μ2-oxo rings on the basal planes of gibbsite is well-constrained chemically. The product is a lithiated layered-double hydroxide solid that forms via in situ phase change. The reaction has well established kinetics and is associated with a distinct swelling of the gibbsite as counter ions enter the interlayer to balance the charge of lithiation. Lithium reacts to fill a fixed and well identifiable crystallographic site and has no solvation waters. Our lithium-isotope data shows that 6Li is favored during this intercalation and that the solid-solution fractionation depends on temperature, electrolyte concentration and counter ion identity (whether Cl-, NO3- or ClO4-). We find that the amount of isotopic fractionation between solid and solution (ΔLisolid-solution) varies with the amount of lithium taken up into the gibbsite structure, which itself depends upon the extent of conversion and also varies with electrolyte concentration and in the counter ion in the order: ClO4- < NO3- < Cl-. Higher electrolyte concentrations cause more rapid expansion of the gibbsite interlayer and some counter ions, such as Cl-, are more easily taken up than others, probably because they ease diffusion. The relationship between lithium loading and ΔLisolid-solution indicates two stages: (1) uptake into the crystallographic sites that favors light lithium, in parallel with adsorption of solvated cations, and (2) continued uptake of solvated cations after all available octahedral vacancies are filled; this second stage has no isotopic preference. The two-step reaction progress is supported by solid-state NMR spectra that clearly resolve a second reservoir of lithium in addition to the expected layered double-hydroxide phase.

  6. Lithium-Induced Downbeat Nystagmus and Horizontal Gaze Palsy.

    PubMed

    Jørgensen, Jesper Skovlund; Landschoff Lassen, Lisbeth; Wegener, Marianne

    2016-01-01

    We report a case of lithium-induced downbeat nystagmus and horizontal gaze palsy in a 62-year-old woman who was treated for a bipolar affective disorder with lithium carbonate for one month. At presentation serum lithium was within therapeutic range. No alternative causes of the ocular motility disturbances were found, and the patient improved significantly as lithium carbonate was discontinued. PMID:27347248

  7. Methods for making lithium vanadium oxide electrode materials

    DOEpatents

    Schutts, Scott M.; Kinney, Robert J.

    2000-01-01

    A method of making vanadium oxide formulations is presented. In one method of preparing lithium vanadium oxide for use as an electrode material, the method involves: admixing a particulate form of a lithium compound and a particulate form of a vanadium compound; jet milling the particulate admixture of the lithium and vanadium compounds; and heating the jet milled particulate admixture at a temperature below the melting temperature of the admixture to form lithium vanadium oxide.

  8. State of the art in high power lithium batteries

    NASA Astrophysics Data System (ADS)

    Chenebault, P.; Planchat, J. P.

    The features of liquid cathode systems used in high-power lithium batteries are reviewed. Practical examples representing the state of the art in the field of high-power lithium batteries are presented, illustrating the advantages and limitations of high-power lithium batteries. Other potentially substitute systems are examined. It is concluded that the high-rate lithium/sulfur oxychloride couples remain the most interesting systems in terms of energy density and specific power, especially in the reserve configuration.

  9. Antiproliferative Potential of Officinal Forms and Nanoparticles of Lithium Salts.

    PubMed

    Lykov, A P; Poveshchenko, O V; Bondarenko, N A; Bogatova, N P; Makarova, O P; Konenkov, V I

    2016-04-01

    We studied the effect of officinal forms and nanoparticles of lithium carbonate and lithium citrate on proliferative activity of hepatoma-29 cells. Lithium carbonate nanoparticles suppressed proliferation of hepatoma-29 cells in lower concentrations than officinal form of this salt. The antiproliferative effect of lithium salts i activation of apoptosis and arrest of hepatoma-29 cells in the G2/M phase of the cell cycle. PMID:27165073

  10. Lithium-Induced Downbeat Nystagmus and Horizontal Gaze Palsy

    PubMed Central

    Jørgensen, Jesper Skovlund; Landschoff Lassen, Lisbeth; Wegener, Marianne

    2016-01-01

    We report a case of lithium-induced downbeat nystagmus and horizontal gaze palsy in a 62-year-old woman who was treated for a bipolar affective disorder with lithium carbonate for one month. At presentation serum lithium was within therapeutic range. No alternative causes of the ocular motility disturbances were found, and the patient improved significantly as lithium carbonate was discontinued. PMID:27347248

  11. Doping-Enhanced Lithium Diffusion in Lithium-Ion Batteries

    NASA Astrophysics Data System (ADS)

    Wu, Gang; Wu, Shunnian; Wu, Ping

    2011-09-01

    We disclose a distortion-assisted diffusion mechanism in Li3N and Li2.5Co0.5N by first-principles simulations. A B2g soft mode at the Γ point is found in α-Li3N, and a more stable α'-Li3N (P3¯m1) structure, which is 0.71 meV lower in energy, is further derived. The same soft mode is inherited into Li2.5Co0.5N and is enhanced due to Co doping. Consequently, unlike the usual Peierls spin instability along Co-N chains, large lithium-ion displacements on the Li-N plane are induced by a set of soft modes. Such a distortion is expected to offer Li atoms a route to bypass the high diffusion barrier and promote Li-ion conductivity. In addition, we further illustrate abnormal Born effective charges along Co-N chains which result from the competition between the motions of electrons and ion cores. Our results provide future opportunities in both fundamental understanding and structural modifications of Li-ion battery materials.

  12. Secondary electron emission from lithium and lithium compounds

    DOE PAGESBeta

    Capece, A. M.; Patino, M. I.; Raitses, Y.; Koel, B. E.

    2016-07-06

    In this work, measurements of electron-induced secondary electron emission ( SEE) yields of lithium as a function of composition are presented. The results are particularly relevant for magnetic fusion devices such as tokamaks, field-reversed configurations, and stellarators that consider Li as a plasma-facing material for improved plasma confinement. SEE can reduce the sheath potential at the wall and cool electrons at the plasma edge, resulting in large power losses. These effects become significant as the SEE coefficient, γe, approaches one, making it imperative to maintain a low yield surface. This work demonstrates that the yield from Li strongly depends onmore » chemical composition and substantially increases after exposure to oxygen and water vapor. The total yield was measured using a retarding field analyzer in ultrahigh vacuum for primary electron energies of 20-600 eV. The effect of Li composition was determined by introducing controlled amounts of O2 and H2O vapor while monitoring film composition with Auger electron spectroscopy and temperature programmed desorption. The results show that the energy at which γe = 1 decreases with oxygen content and is 145 eV for a Li film that is 17% oxidized and drops to less than 25 eV for a fully oxidized film. This work has important implications for laboratory plasmas operating under realistic vacuum conditions in which oxidation significantly alters the electron emission properties of Li walls. Published by AIP Publishing.« less

  13. Secondary electron emission from lithium and lithium compounds

    NASA Astrophysics Data System (ADS)

    Capece, A. M.; Patino, M. I.; Raitses, Y.; Koel, B. E.

    2016-07-01

    In this work, measurements of electron-induced secondary electron emission (SEE) yields of lithium as a function of composition are presented. The results are particularly relevant for magnetic fusion devices such as tokamaks, field-reversed configurations, and stellarators that consider Li as a plasma-facing material for improved plasma confinement. SEE can reduce the sheath potential at the wall and cool electrons at the plasma edge, resulting in large power losses. These effects become significant as the SEE coefficient, γe, approaches one, making it imperative to maintain a low yield surface. This work demonstrates that the yield from Li strongly depends on chemical composition and substantially increases after exposure to oxygen and water vapor. The total yield was measured using a retarding field analyzer in ultrahigh vacuum for primary electron energies of 20-600 eV. The effect of Li composition was determined by introducing controlled amounts of O2 and H2O vapor while monitoring film composition with Auger electron spectroscopy and temperature programmed desorption. The results show that the energy at which γe = 1 decreases with oxygen content and is 145 eV for a Li film that is 17% oxidized and drops to less than 25 eV for a fully oxidized film. This work has important implications for laboratory plasmas operating under realistic vacuum conditions in which oxidation significantly alters the electron emission properties of Li walls.

  14. Nanostructured lithium sulfide materials for lithium-sulfur batteries

    NASA Astrophysics Data System (ADS)

    Lee, Sang-Kyu; Lee, Yun Jung; Sun, Yang-Kook

    2016-08-01

    Upon the maturation and saturation of Li-ion battery technologies, the demand for the development of energy storage systems with higher energy densities has surged to meet the needs of key markets such as electric vehicles. Among the many next generation high-energy storage options, the Lisbnd S battery system is considered particularly close to mass commercialization because of its low cost and the natural abundance of sulfur. In this review, we focus on nanostructured Li2S materials for Lisbnd S batteries. Due to a lithium source in its molecular structure, Li2S can be coupled with various Li-free anode materials, thereby giving it the potential to surmount many of the problems related with a Li-metal anode. The hurdles that impede the full utilization of Li2S materials include its high activation barrier and the low electrical conductivity of bulk Li2S particles. Various strategies that can be used to assist the activation process and facilitate electrical transport are analyzed. To provide insight into the opportunities specific to Li2S materials, we highlight some major advances and results that have been achieved in the development of metal Li-free full cells and all-solid-state cells based on Li2S cathodes.

  15. A study of aluminum-lithium alloys: Strength profile in 2090 aluminum-lithium-copper-magnesium-zirconium alloy

    SciTech Connect

    Soepriyanto, S.

    1991-01-01

    Aluminum-containing lithium alloys are undergoing intensive development as replacements for conventional aluminum alloys 2024 and 7075 in aircraft structural applications. Lithium is a very reactive metal so that an elevated temperature heat treatments can cause lithium diffusion to the surface and reaction with the atmosphere. Solid state diffusion of lithium within the 2090 alloy and subsequent surface oxidation during solution heat treatment were investigated. Thermodynamic and kinetic analyses were used to evaluate the alloy's thermal oxidation behavior. A mathematical model based on simultaneous diffusion and surface oxidation of lithium was developed to predict lithium concentration profiles across the specimen. Agreement was obtained between the predicted lithium concentration profiles and their corresponding experimental results. Microhardness and yield strength profiles were found also to follow the corresponding lithium concentration profiles. Various heat treatment procedures were studied on this 2090 alloy to give a greater understanding of precipitate strengthening.

  16. 40 CFR 721.10201 - Cobalt lithium manganese nickel oxide.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Cobalt lithium manganese nickel oxide... Specific Chemical Substances § 721.10201 Cobalt lithium manganese nickel oxide. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as cobalt lithium...

  17. 40 CFR 721.10201 - Cobalt lithium manganese nickel oxide.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Cobalt lithium manganese nickel oxide... Specific Chemical Substances § 721.10201 Cobalt lithium manganese nickel oxide. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as cobalt lithium...

  18. 40 CFR 721.10201 - Cobalt lithium manganese nickel oxide.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Cobalt lithium manganese nickel oxide... Specific Chemical Substances § 721.10201 Cobalt lithium manganese nickel oxide. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as cobalt lithium...

  19. LONG-LASTING LITHIUM NEUROTOXICITY IN AN ADOLESECENT

    PubMed Central

    Khanna, Rakesh; Sethi, Sujata

    1993-01-01

    SUMMARY Acute lithium intoxication is well known. A case of long tasting lithium neurotoxicity in an adolescent male is reported, who showed signs of cerebellar as well as brain stem involvement. Persistent lithium neurotoxicity is discussed and the recommendation made that this condition be considered irreversible only if no substantial recovery occurs in the first six months. PMID:21743620

  20. Adverse reactions in treatment with lithium carbonate and haloperidol.

    PubMed

    Baastrup, P C; Hollnagel, P; Sorensen, R; Schou, M

    1976-12-01

    Hospital records of 425 patients who had been treated simultaneously with lithium carbonate and haloperidol were examined. Adverse reactions in these patients were the same as in patients given lithium alone or haloperidol alone. None of the patients developed a syndrome resembling that described by others in patients treated with a lithium and haloperidol combination. PMID:1036539

  1. 78 FR 19024 - Lithium Ion Batteries in Transportation Public Forum

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-03-28

    ... SAFETY BOARD Lithium Ion Batteries in Transportation Public Forum On Thursday and Friday, April 11-12, 2013, the National Transportation Safety Board (NTSB) will convene a forum titled, ``Lithium Ion... Inquiry. The forum is organized into three topic areas: Lithium ion battery design, development, and...

  2. 75 FR 9147 - Hazardous Materials: Transportation of Lithium Batteries

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-03-01

    ... equipment (HM-224F; 75 FR 1302). The proposed changes are intended to enhance safety by ensuring that all... for lithium metal batteries and lithium ion batteries were adopted into the UN Recommendations. The... regulations were revised to reflect this change. Adopt shipping descriptions for lithium ion...

  3. 40 CFR 721.9668 - Organotin lithium compound.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Organotin lithium compound. 721.9668... Substances § 721.9668 Organotin lithium compound. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance generically identified as an organotin lithium compound (PMN...

  4. 40 CFR 721.9668 - Organotin lithium compound.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Organotin lithium compound. 721.9668... Substances § 721.9668 Organotin lithium compound. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance generically identified as an organotin lithium compound (PMN...

  5. 40 CFR 721.9668 - Organotin lithium compound.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Organotin lithium compound. 721.9668... Substances § 721.9668 Organotin lithium compound. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance generically identified as an organotin lithium compound (PMN...

  6. 40 CFR 721.9668 - Organotin lithium compound.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Organotin lithium compound. 721.9668... Substances § 721.9668 Organotin lithium compound. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance generically identified as an organotin lithium compound (PMN...

  7. 40 CFR 721.9668 - Organotin lithium compound.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Organotin lithium compound. 721.9668... Substances § 721.9668 Organotin lithium compound. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance generically identified as an organotin lithium compound (PMN...

  8. Superacid-Based Lithium Salts For Polymer Electrolytes

    NASA Technical Reports Server (NTRS)

    Nagasubramanian, Ganesan; Prakash, Surya; Shen, David H.; Surampudi, Subbarao; Olah, George

    1995-01-01

    Solid polymer electrolytes exhibiting high lithium-ion conductivities made by incorporating salts of superacids into thin films of polyethylene oxide (PEO). These and other solid-polymer electrolytes candidates for use in rechargeable lithium-based electrochemical cells. Increases in room-temperature lithium-ion conductivities of solid electrolytes desirable because they increase achievable power and energy densities.

  9. 40 CFR 721.10332 - Lithium metal phosphate (generic).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Lithium metal phosphate (generic). 721... Substances § 721.10332 Lithium metal phosphate (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as lithium metal phosphate (PMN...

  10. RECOVERY AND SEPARATION OF LITHIUM VALUES FROM SALVAGE SOLUTIONS

    DOEpatents

    Hansford, D.L.; Raabe, E.W.

    1963-08-20

    Lithium values can be recovered from an aqueous basic solution by reacting the values with a phosphate salt soluble in the solution, forming an aqueous slurry of the resultant aqueous insoluble lithium phosphate, contacting the slurry with an organic cation exchange resin in the acid form until the slurry has been clarified, and thereafter recovering lithium values from the resin. (AEC)

  11. 40 CFR 721.10332 - Lithium metal phosphate (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Lithium metal phosphate (generic). 721... Substances § 721.10332 Lithium metal phosphate (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as lithium metal phosphate (PMN...

  12. 40 CFR 721.10332 - Lithium metal phosphate (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Lithium metal phosphate (generic). 721... Substances § 721.10332 Lithium metal phosphate (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as lithium metal phosphate (PMN...

  13. Electrolytes for rechargeable lithium batteries. Research and development technical report

    SciTech Connect

    Hunger, H.F.

    1981-09-01

    Theoretical considerations predict increased stability of cyclic ethers and diethers against reductive cleavage by lithium if the ethers have 2 methyl substitution. Diethers are solvents with low viscosity which are desirable for high rate rechargeable lithium batteries. Synergistic, mixed solvent effects increase electrolyte conductance and rate capability of lithium intercalating cathodes.

  14. Multilayer Approach for Advanced Hybrid Lithium Battery.

    PubMed

    Ming, Jun; Li, Mengliu; Kumar, Pushpendra; Li, Lain-Jong

    2016-06-28

    Conventional intercalated rechargeable batteries have shown their capacity limit, and the development of an alternative battery system with higher capacity is strongly needed for sustainable electrical vehicles and hand-held devices. Herein, we introduce a feasible and scalable multilayer approach to fabricate a promising hybrid lithium battery with superior capacity and multivoltage plateaus. A sulfur-rich electrode (90 wt % S) is covered by a dual layer of graphite/Li4Ti5O12, where the active materials S and Li4Ti5O12 can both take part in redox reactions and thus deliver a high capacity of 572 mAh gcathode(-1) (vs the total mass of electrode) or 1866 mAh gs(-1) (vs the mass of sulfur) at 0.1C (with the definition of 1C = 1675 mA gs(-1)). The battery shows unique voltage platforms at 2.35 and 2.1 V, contributed from S, and 1.55 V from Li4Ti5O12. A high rate capability of 566 mAh gcathode(-1) at 0.25C and 376 mAh gcathode(-1) at 1C with durable cycle ability over 100 cycles can be achieved. Operando Raman and electron microscope analysis confirm that the graphite/Li4Ti5O12 layer slows the dissolution/migration of polysulfides, thereby giving rise to a higher sulfur utilization and a slower capacity decay. This advanced hybrid battery with a multilayer concept for marrying different voltage plateaus from various electrode materials opens a way of providing tunable capacity and multiple voltage platforms for energy device applications. PMID:27268064

  15. Electrochemical analysis of lithium polymer batteries

    NASA Astrophysics Data System (ADS)

    Han, Yong-Bong

    Lithium batteries consist of lithium anode, polymer electrolyte separator, and the porous, composite cathode. Lithium batteries have been very attractive to the battery industries because lithium metal has an extremely high energy density. The use of lithium metal can cause dendrite formation by uneven electro-deposition during charge. The lithium battery can explode in a liquid electrolyte when it is shorted by the dendrite. It has been reported that the mechanical properties of a polymer electrolyte can retard the dendrite initiation. We have attempted to study the dendrite initiation quantitatively by developing a mathematical model that evaluates the behavior of the interface and by performing dendrite-initiation experiments with the use of cross-linked polymer electrolytes to vary the mechanical properties of the electrolyte. Cross-linking the polymer backbone may decrease the transport properties of the polymer electrolyte. The transport properties are diffusion coefficient, ionic conductivity, and transference number of the electrolyte. When poor transport properties of the polymer electrolyte cause salt depletion at the cathode at low salt concentrations, side reactions and dendrite initiation can be accelerated. In order to study how cross-linking the polymer backbone affects the transport properties, the transport properties are measured experimentally by LBNL method which is based on concentrated solution theory. Porous electrodes are commonly used as the cathode in lithium battery systems. Because the electrochemical reaction occurs at the active particles in the porous, composite cathode during charge and discharge, the kinetics of the electrochemical reaction at the active particles in the cathode affects the battery performance. AC impedance has been broadly used to study the kinetics of the electrochemical reaction in the cathode. However, the AC impedance spectra have been analyzed by regarding the porous cathode as a planar electrode by most

  16. Diffusive Fractionation of Lithium Isotopes in Olivine

    NASA Astrophysics Data System (ADS)

    Homolova, V.; Richter, F. M.; Watson, E. B.; Chaussidon, M.

    2014-12-01

    Systematic lithium isotope variations along concentration gradients found in olivine and pyroxene grains from terrestrial, lunar and martian rocks have been attributed to diffusive isotopic fractionation [Beck et al., 2006; Tang et al., 2007]. In some cases, these isotopic excursions are so large that a single grain may display isotopic variability that spans almost the entire range of documented terrestrial values [Jeffcoate et al., 2007]. In this study, we present the results of experiments to examine diffusive isotopic fractionation of lithium in olivine. The experiments comprised crystallographically oriented slabs of San Carlos olivine juxtaposed with either spodumene powder or a lithium rich pyroxene crystal. Experiments were conducted at 1 GPa and 0.1MPa over a temperature range of 1000 to 1125⁰C. Oxygen fugacity in the 0.1MPa experiments was controlled using the wustite-magnetite and nickel-nickel oxide solid buffer assemblages. Lithium concentrations generally decrease smoothly away from the edges of the grains; however, experiments involving diffusion parallel to the a-axis consistently show peculiar wavy or segmented concentration profiles. Lithium diffusivity parallel to the c-axis is on the order of 1E-14m2/s at 1100⁰C. The diffusivity parallel to the c-axis is more than an order of magnitude faster than diffusion parallel to the b-axis and correlates positively with oxygen fugacity. The lithium isotopic composition, δ7Li = 1000‰ * ((δ7Lisample- δ7Ligrain center)/ δ7Ligrain center), shows a decrease away from the edge of the grain to a minimum value (up to 70‰ lighter) and then an abrupt increase back to the initial isotopic composition of the olivine grain. This isotopic profile is similar to those found in natural grains and an experimental study on diffusive fractionation of lithium isotopes in pyroxene [Richter et al., 2014]. Results from the present study are modeled using the approach of Dohmen et al. [2010], which assumes lithium

  17. Rotation, inflation, and lithium in the Pleiades

    NASA Astrophysics Data System (ADS)

    Somers, Garrett; Pinsonneault, Marc H.

    2015-06-01

    The rapidly rotating cool dwarfs of the Pleiades are rich in lithium relative to their slowly rotating counterparts. Motivated by observations of inflated radii in young, active stars, and by calculations showing that radius inflation inhibits pre-main-sequence (pre-MS) Li destruction, we test whether this pattern could arise from a connection between stellar rotation rate and radius inflation on the pre-MS. We demonstrate that pre-MS radius inflation can efficiently suppress lithium destruction by rotationally induced mixing in evolutionary models, and that the net effect of inflation and rotational mixing is a pattern where rotation correlates with lithium abundance for M* < M⊙, and anticorrelates with lithium abundance for M* > M⊙, similar to the empirical trend in the Pleiades. Next, we adopt different prescriptions for the dependence of inflation on rotation, and compare their predictions to the Pleiades lithium/rotation pattern. We find that if a connection between rotation and radius inflation exists, then the important qualitative features of this pattern naturally and generically emerge in our models. This is the first consistent physical model to date that explains the Li-rotation correlation in the Pleiades. We discuss plausible mechanisms for inducing this correlation and suggest an observational test using granulation.

  18. Magnetic diagnostics for the lithium tokamak experiment.

    PubMed

    Berzak, L; Kaita, R; Kozub, T; Majeski, R; Zakharov, L

    2008-10-01

    The lithium tokamak experiment (LTX) is a spherical tokamak with R(0)=0.4 m, a=0.26 m, B(TF) approximately 3.4 kG, I(P) approximately 400 kA, and pulse length approximately 0.25 s. The focus of LTX is to investigate the novel low-recycling lithium wall operating regime for magnetically confined plasmas. This regime is reached by placing an in-vessel shell conformal to the plasma last closed flux surface. The shell is heated and then coated with liquid lithium. An extensive array of magnetic diagnostics is available to characterize the experiment, including 80 Mirnov coils (single and double axis, internal and external to the shell), 34 flux loops, 3 Rogowskii coils, and a diamagnetic loop. Diagnostics are specifically located to account for the presence of a secondary conducting surface and engineered to withstand both high temperatures and incidental contact with liquid lithium. The diagnostic set is therefore fabricated from robust materials with heat and lithium resistance and is designed for electrical isolation from the shell and to provide the data required for highly constrained equilibrium reconstructions. PMID:19044600

  19. Size effects in lithium ion batteries

    NASA Astrophysics Data System (ADS)

    Hu-Rong, Yao; Ya-Xia, Yin; Yu-Gao, Guo

    2016-01-01

    Size-related properties of novel lithium battery materials, arising from kinetics, thermodynamics, and newly discovered lithium storage mechanisms, are reviewed. Complementary experimental and computational investigations of the use of the size effects to modify electrodes and electrolytes for lithium ion batteries are enumerated and discussed together. Size differences in the materials in lithium ion batteries lead to a variety of exciting phenomena. Smaller-particle materials with highly connective interfaces and reduced diffusion paths exhibit higher rate performance than the corresponding bulk materials. The thermodynamics is also changed by the higher surface energy of smaller particles, affecting, for example, secondary surface reactions, lattice parameter, voltage, and the phase transformation mechanism. Newly discovered lithium storage mechanisms that result in superior storage capacity are also briefly highlighted. Project supported by the National Natural Science Foundation of China (Grant Nos. 51225204 and 21303222), the Shandong Taishan Scholarship, China, the Ministry of Science and Technology, China (Grant No. 2012CB932900), and the Strategic Priority Research Program of the Chinese Academy of Sciences (Grant No. XDA09010000).

  20. Mechanochemistry of lithium nitride under hydrogen gas.

    PubMed

    Li, Z; Zhang, J; Wang, S; Jiang, L; Latroche, M; Du, J; Cuevas, F

    2015-09-14

    Hydrogen uptake during the mechanochemistry of lithium nitride under 9 MPa hydrogen pressure has been analyzed by means of in situ solid-gas absorption and ex situ X-ray diffraction (XRD) measurements. In situ hydrogenation curves show two H-sorption steps leading to an overall hydrogen uptake of 9.8 wt% H after 3 hours of milling. The milled end-products consist of nanocrystalline (∼10 nm) LiNH2 and LiH phases. The first reaction step comprises the transformation of the polymorph α-Li3N (S.G. P6/mmm) into the β-Li3N (S.G. P63/mmc) metastable phase and the reaction of the latter with hydrogen to form lithium imide: β-Li3N + H2→ Li2NH + LiH. Reaction kinetics of the first step is zero-order. Its rate-limiting control is assigned to the collision frequency between milling balls and Li3N powder. In the second absorption step, lithium imide converts to lithium amide following the reaction scheme Li2NH + H2→ LiNH2 + LiH. Reaction kinetics is here limited by one-dimensional nucleation and the growth mechanism, which, in light of structural data, is assigned to the occurrence of lithium vacancies in the imide compound. This study provides new insights into the reaction paths and chemical kinetics of light hydrogen storage materials during their mechanochemical synthesis. PMID:26234206

  1. Lithium-Ion Cell Charge Control Unit

    NASA Technical Reports Server (NTRS)

    Reid, Concha; Button, Robert; Manzo, Michelle; McKissock, Barbara; Miller, Thomas; Gemeiner, Russel; Bennett, William; Hand, Evan

    2006-01-01

    Life-test data of Lithium-Ion battery cells is critical in order to establish their performance capabilities for NASA missions and Exploration goals. Lithium-ion cells have the potential to replace rechargeable alkaline cells in aerospace applications, but they require a more complex charging scheme than is typically required for alkaline cells. To address these requirements in our Lithium-Ion Cell Test Verification Program, a Lithium-Ion Cell Charge Control Unit was developed by NASA Glenn Research Center (GRC). This unit gives researchers the ability to test cells together as a pack, while allowing each cell to charge individually. This allows the inherent cell-to-cell variations to be addressed on a series string of cells and results in a substantial reduction in test costs as compared to individual cell testing. The Naval Surface Warfare Center at Crane, Indiana developed a power reduction scheme that works in conjunction with the Lithium-Ion Cell Charge Control Unit. This scheme minimizes the power dissipation required by the circuitry to prolong circuit life and improve its reliability.

  2. Lithium Release Experiment in the Thermosphere

    NASA Astrophysics Data System (ADS)

    Watanabe, Shigeto; Abe, Takumi; Habu, Hiroto; Nakamura, Masato; Ono, Takayuki; Otsuka, Yuichi; Saito, Akinori; Yamamoto, Mamoru; Yamamoto, Masa-Yuki

    Though the ionization rate is less than 1% in the region of thermosphere, the dynamics of neutral atmosphere is strongly controlled by the plasma. However, the direct observation is not yet performed in detail. JAXA/ISAS launched successfully S-520-23 sounding rocket from Kagoshima Space Center (KSC) in the evening of September 2, 2007. The rocket experiment is called WIND (Wind measurement for Ionized and Neutral atmospheric Dynamics study). The purpose is to investigate the neutral atmosphere - plasma coupling process in F-region through the measurements of atmospheric circulation and super rotation in the low latitude thermosphere, and a medium scale traveling ionospheric disturbance (MS-TID) occurring in the mid-latitude ionosphere. The rocket installed Lithium Release Canisters as well as instruments for plasma drift velocity, plasma density and temperature and its fluctuations, and electric and magnetic fields. The Lithium gas was released at altitudes between 150km and 300km, and the Lithium scattered sunlight by resonance scattering with wavelength of 670nm. The neutral winds in the thermosphere were estimated from the movements of Lithium Clouds observed by CCD imagers on ground. From the diffusion of Lithium Clouds, we estimated neutral density and temperature in the thermosphere.

  3. Evaporated Lithium Surface Coatings in NSTX

    SciTech Connect

    Kugel, H. W.; Mansfield, D.; Maingi, R.; Bel, M. G.; Bell, R. E.; Allain, J. P.; Gates, D.; Gerhardt, S.; Kaita, R.; Kallman, J.; Kaye, S.; LeBlanc, B.; Majeski, R.; Menard, J.; Mueller, D.; Ono, M.

    2009-04-09

    Two lithium evaporators were used to evaporate more than 100 g of lithium on to the NSTX lower divertor region. Prior to each discharge, the evaporators were withdrawn behind shutters, where they also remained during the subsequent HeGDC applied for periods up to 9.5 min. After the HeGDC, the shutters were opened and the LITERs were reinserted to deposit lithium on the lower divertor target for 10 min, at rates of 10-70 mg/min, prior to the next discharge. The major improvements in plasma performance from these lithium depositions include: 1) plasma density reduction as a result of lithium deposition; 2) suppression of ELMs; 3) improvement of energy confinement in a low-triangularity shape; 4) improvement in plasma performance for standard, high-triangularity discharges; 5) reduction of the required HeGDC time between discharges; 6) increased pedestal electron and ion temperature; 7) reduced SOL plasma density; and 8) reduced edge neutral density.

  4. Role of Constituent Hard Polymer in Enhancing Lithium Transference Number of Lithium Salt-Polymer Complexes

    NASA Astrophysics Data System (ADS)

    Jo, Gyuha; Park, Moon Jeong

    2015-03-01

    Lithium polymer batteries have been projected as promising energy storage systems, owing to their unique advantages such as long cycle life, high specific capacity, and high cell potential. While the polymer electrolytes such as poly(ethylene oxide) (PEO) employed in lithium polymer batteries have high ionic conductivity and low volatility, the PEO-lithium salt complexes indicated immense shortcomings of concentration polarization, ascribed to the motion of free anions within PEO. This has limited charge/discharge rate of lithium batteries. In this study, we present a new methodology for improving the ionic conductivity and lithium transference number of PEO, by block copolymerization with a hard polymer, namely poly(dithiooxamide) (PDTOA). Compared to a simple PEO/PDTOA blend, lithium-salt doped PEO-b-PDTOA block copolymers exhibited significantly improved ionic conductivity values. Further, lithium transference numbers as high as 0.66 were observed, which are much higher than the corresponding values for conventional PEO-salt electrolytes (~ 0 . 25).

  5. LITHIUM IN AFFECTIVE DISORDERS : A SEVEN YEAR OBSERVATION OF LITHIUM CLINIC

    PubMed Central

    Sethi, B.B.; Dalal, P.K.; Trivedi, J.K.

    1984-01-01

    SUMMARY Out of 692 patients registered in the lithium clinic, King George's Medical College, Lucknow, 122 patients suffering from affective disorders, receiving lithium for at least 6 months continuously, having had at least 5 serum lithium estimations done and having been evaluated at least once in 6 months while on follow-up, were analysed with a view to study the relapses. About one-third patients suffered no relapse while on lithium. The study revealed that longer the duration of lithium treatment lesser were the frequency, number, intensity and duration of manic/depressive relapses. Majority of patients were maintained on the lower side (0.5-0.8 mEq/L) of the usually recommended therapeutic range (0.6-1.2 mEq/L) for lithium prophylaxis. Commonly observed side effects include fine tremors, muscular weakness, polyuria, polydipsia and constipation. All the side effects were easily managed and none had a fatal sides-effect. A reappraisal in the light of existing literature of lithium prophylaxis on manic depressive psychosis is done. PMID:21966016

  6. Method for fabricating carbon/lithium-ion electrode for rechargeable lithium cell

    NASA Technical Reports Server (NTRS)

    Huang, Chen-Kuo (Inventor); Surampudi, Subbarao (Inventor); Attia, Alan I. (Inventor); Halpert, Gerald (Inventor)

    1995-01-01

    The method includes steps for forming a carbon electrode composed of graphitic carbon particles adhered by an ethylene propylene diene monomer binder. An effective binder composition is disclosed for achieving a carbon electrode capable of subsequent intercalation by lithium ions. The method also includes steps for reacting the carbon electrode with lithium ions to incorporate lithium ions into graphitic carbon particles of the electrode. An electrical current is repeatedly applied to the carbon electrode to initially cause a surface reaction between the lithium ions and to the carbon and subsequently cause intercalation of the lithium ions into crystalline layers of the graphitic carbon particles. With repeated application of the electrical current, intercalation is achieved to near a theoretical maximum. Two differing multi-stage intercalation processes are disclosed. In the first, a fixed current is reapplied. In the second, a high current is initially applied, followed by a single subsequent lower current stage. Resulting carbon/lithium-ion electrodes are well suited for use as an anode in a reversible, ambient temperature, lithium cell.

  7. Characterization of plasticity and fracture of shell casing of lithium-ion cylindrical battery

    NASA Astrophysics Data System (ADS)

    Zhang, Xiaowei; Wierzbicki, Tomasz

    2015-04-01

    Most of the literature on lithium-ion battery cells is concerned with modeling of jellyroll with little attention to properties of shell casing. However, shell casing provides substantial strength and fracture resistance under mechanical loading and therefore must be an important part of modeling of lithium-ion batteries. The paper reports on a comprehensive test program on commercially available empty shell casing of 18650 lithium-ion cylindrical cells. Part of the tests was used to determine plastic and fracture properties from sub-size specimens cut from lateral part of the cans. The other part served to validate plasticity and fracture models under various loading conditions. The associated flow rule was used to simulate plasticity behavior and Modified Mohr-Coulomb (MMC) fracture model was adopted to predict crack initiation and propagation of shell casing. Simulation results confirmed that present plasticity and fracture models could predict global plastic behavior of the cells under different loading conditions. The jellyroll model with volumetric hardening was introduced to compare the performance of empty shell casing, bare jellyroll and complete battery cell. It was shown that in many loading situations, for example, three point bending of the cylindrical cells, the metallic shell casing provides most of mechanical resistance.

  8. Electronic structure of lithium amide

    NASA Astrophysics Data System (ADS)

    Kamakura, N.; Takeda, Y.; Saitoh, Y.; Yamagami, H.; Tsubota, M.; Paik, B.; Ichikawa, T.; Kojima, Y.; Muro, T.; Kato, Y.; Kinoshita, T.

    2011-01-01

    The electronic structure of the insulator lithium amide (LiNH2), which is a lightweight complex hydride being considered as a high-capacity hydrogen storage material, is investigated by N 1s soft x-ray emission spectroscopy (XES) and absorption spectroscopy (XAS). The XES and XAS spectra show a band gap between the valence and conduction bands. The valence band in the XES spectrum consists of three peaks, which extend up to ~-8 eV from the valence band top. The band calculation within the local-density approximation (LDA) for LiNH2shows energetically separated three peaks in the occupied N 2p partial density of states (pDOS) and the band gap. The energy distribution of three peaks in the XES spectrum agrees with that in the calculated pDOS except for the peak at the highest binding energy, which is attributed to the strongly hybridized state between N 2p and H 1s. The XES experiment has clarified that the strongly hybridized state with H 1s in LiNH2is located at binding energy higher than that of the LDA calculation, while the overall feature of the electronic structure of LiNH2experimentally obtained by XES and XAS is consistent with the calculated result.

  9. Analysis of lithium driven electron density peaking in FTU liquid lithium limiter experiments

    NASA Astrophysics Data System (ADS)

    Szepesi, G.; Romanelli, M.; Militello, F.; Peeters, A. G.; Camenen, Y.; Casson, F. J.; Hornsby, W. A.; Snodin, A. P.; Wágner, D.; the FTU Team

    2013-03-01

    The impact of lithium impurities on the microstability and turbulent transport characteristics in the core of a typical FTU liquid lithium limiter (LLL) (Mazzitelli et al 2011 Nucl. Fusion 51 073006) discharge during the density ramp-up phase is studied. A non-linear gyrokinetic analysis performed with GKW (Peeters et al 2009 Comput. Phys. Commun. 180 2650) accompanied by a quasi-linear fluid analysis is presented. We show that a centrally peaked, high concentration lithium profile contributes to the electron peaking by reducing the outward electron flux, and that it leads to inward turbulent deuterium transport through ion flux separation.

  10. Lithium Ion Electrolytes and Lithium Ion Cells With Good Low Temperature Performance

    NASA Technical Reports Server (NTRS)

    Smart, Marshall C. (Inventor); Bugga, Ratnakumar V. (Inventor)

    2014-01-01

    There is provided in one embodiment of the invention an electrolyte for use in a lithium ion electrochemical cell. The electrolyte comprises a mixture of an ethylene carbonate (EC), an ethyl methyl carbonate (EMC), an ester cosolvent, and a lithium salt. The ester cosolvent comprises methyl propionate (MP), ethyl propionate (EP), methyl butyrate (MB), ethyl butyrate (EB), propyl butyrate (PB), or butyl butyrate (BB). The electrochemical cell operates in a temperature range of from about -60 C to about 60 C. In another embodiment there is provided a lithium ion electrochemical cell using the electrolyte of the invention.

  11. A Stable Fluorinated and Alkylated Lithium Malonatoborate Salt for Lithium Ion Battery Application

    SciTech Connect

    Dai, Sheng; Sun, Xiao-Guang

    2015-01-01

    A new fluorinated and alkylated lithium malonatoborate salt, lithium bis(2-methyl-2-fluoromalonato)borate (LiBMFMB), has been synthesized for lithium ion battery application. A 0.8 M LiBMFMB solution is obtained in a mixture of ethylene carbonate (EC) and ethyl methyl carbonate (EMC) (1:2 by wt.). The new LiBMFMB based electrolyte exhibits good cycling stability and rate capability in LiNi0.5Mn1.5O4 and graphite based half-cells.

  12. A Stable Fluorinated and Alkylated Lithium Malonatoborate Salt for Lithium Ion Battery Application

    DOE PAGESBeta

    Wan, Shun; Jiang, Xueguang; Guo, Bingkun; Dai, Sheng; Goodenough, John B.; Sun, Xiao-Guang

    2015-04-27

    A new fluorinated and alkylated lithium malonatoborate salt, lithium bis(2-methyl-2-fluoromalonato)borate (LiBMFMB), has been synthesized for lithium ion battery application. A 0.8 M LiBMFMB solution is obtained in a mixture of ethylene carbonate (EC) and ethyl methyl carbonate (EMC) (1:2 by wt.). The new LiBMFMB based electrolyte exhibits good cycling stability and rate capability in LiNi0.5Mn1.5O4 and graphite based half-cells.

  13. Thermal Aspects of Lithium Ion Cells

    NASA Technical Reports Server (NTRS)

    Frank, H.; Shakkottai, P.; Bugga, R.; Smart, M.; Huang, C. K.; Timmerman, P.; Surampudi, S.

    2000-01-01

    This viewgraph presentation outlines the development of a thermal model of Li-ion cells in terms of heat generation, thermal mass, and thermal resistance. Intended for incorporation into battery model. The approach was to estimate heat generation: with semi-theoretical model, and then to check accuracy with efficiency measurements. Another objective was to compute thermal mass from component weights and specific heats, and to compute the thermal resistance from component dimensions and conductivities. Two lithium batteries are compared, the Cylindrical lithium battery, and the prismatic lithium cell. It reviews methodology for estimating the heat generation rate. Graphs of the Open-circuit curves of the cells and the heat evolution during discharge are given.

  14. Deuterium Retention in NSTX with Lithium Conditioning

    SciTech Connect

    C.H. Skinner, J.P. Allain, W. Blanchard, H.W. Kugel, R. Maingi, L. Roquemore, V. Soukhanovskii, C.N. Taylor

    2010-06-02

    High (≈ 90%) deuterium retention was observed in NSTX gas balance measurements both withand without lithiumization of the carbon plasma facing components. The gas retained in ohmic discharges was measured by comparing the vessel pressure rise after a discharge to that of a gasonly pulse with the pumping valves closed. For neutral beam heated discharges the gas input and gas pumped by the NB cryopanels were tracked. The discharges were followed by outgassing of deuterium that reduced the retention. The relationship between retention and surface chemistry was explored with a new plasma-material interface probe connected to an in-vacuo surface science station that exposed four material samples to the plasma. XPS and TDS analysis showed that the binding of D atoms is fundamentally changed by lithium - in particular atoms are weakly bonded in regions near lithium atoms bound to either oxygen or the carbon matrix.

  15. Thermoelectric magnetohydrodynamic (TEMHD) stirring of liquid lithium

    NASA Astrophysics Data System (ADS)

    Jaworski, M. A.; Xu, Wenyu; Kim, Jason; Lee, Matt; Neumann, Martin; Surla, Vijay; Ruzic, David

    2009-11-01

    The Solid/Liquid Lithium Divertor Experiment (SLiDE) was constructed to examine passive flows in liquid lithium under an applied heat load and external magnetic field. The offered explanation for the results of the CDX-U experiment, where liquid lithium was capable of transporting >50[MW/m^2] of incident heat flux without rapid evaporation, was thermocapillary (Marangonic) driven flows. The SLiDE apparatus utilizes a line-stripe heat source and external magnetic fields to mimic a divertor scenario to test the thermocapillary hypothesis. Instead of thermocapillary induced flows, TEMHD flows are observed on the order of 10 [cm/s]. The thermoelectric effect was confirmed through a series of qualitative experiments in the apparatus which will be described. A quantitative scaling matching the measured target temperatures and heat fluxes is compared to the measured velocities. A novel plasma facing component based on porous material TEMHD is also presented.

  16. Electrochemical Lithium Ion Battery Performance Model

    Energy Science and Technology Software Center (ESTSC)

    2007-03-29

    The Electrochemical Lithium Ion Battery Performance Model allows for the computer prediction of the basic thermal, electrical, and electrochemical performance of a lithium ion cell with simplified geometry. The model solves governing equations describing the movement of lithium ions within and between the negative and positive electrodes. The governing equations were first formulated by Fuller, Doyle, and Newman and published in J. Electrochemical Society in 1994. The present model solves the partial differential equations governingmore » charge transfer kinetics and charge, species, heat transports in a computationally-efficient manner using the finite volume method, with special consideration given for solving the model under conditions of applied current, voltage, power, and load resistance.« less

  17. Annealing kinetics of electrodeposited lithium dendrites.

    PubMed

    Aryanfar, Asghar; Cheng, Tao; Colussi, Agustin J; Merinov, Boris V; Goddard, William A; Hoffmann, Michael R

    2015-10-01

    The densifying kinetics of lithium dendrites is characterized with effective activation energy of Ea ≈ 6 - 7 kcal mol(-1) in our experiments and molecular dynamics computations. We show that heating lithium dendrites for 55 °C reduces the representative dendrites length λ¯(T,t) up to 36%. NVT reactive force field simulations on three-dimensional glass phase dendrites produced by our coarse grained Monte Carlo method reveal that for any given initial dendrite morphology, there is a unique stable atomic arrangement for a certain range of temperature, combined with rapid morphological transition (∼10 ps) within quasi-stable states involving concurrent bulk and surface diffusions. Our results are useful for predicting the inherent structural characteristics of lithium dendrites such as dominant coordination number. PMID:26450322

  18. Enhanced lithium ion storage in nanoimprinted carbon

    NASA Astrophysics Data System (ADS)

    Wang, Peiqi; Chen, Qian Nataly; Xie, Shuhong; Liu, Xiaoyan; Li, Jiangyu

    2015-07-01

    Disordered carbons processed from polymers have much higher theoretical capacity as lithium ion battery anode than graphite, but they suffer from large irreversible capacity loss and have poor cyclic performance. Here, a simple process to obtain patterned carbon structure from polyvinylpyrrolidone was demonstrated, combining nanoimprint lithography for patterning and three-step heat treatment process for carbonization. The patterned carbon, without any additional binders or conductive fillers, shows remarkably improved cycling performance as Li-ion battery anode, twice as high as the theoretical value of graphite at 98 cycles. Localized electrochemical strain microscopy reveals the enhanced lithium ion activity at the nanoscale, and the control experiments suggest that the enhancement largely originates from the patterned structure, which improves surface reaction while it helps relieving the internal stress during lithium insertion and extraction. This study provides insight on fabricating patterned carbon architecture by rational design for enhanced electrochemical performance.

  19. Enhanced lithium ion storage in nanoimprinted carbon

    SciTech Connect

    Wang, Peiqi; Chen, Qian Nataly; Li, Jiangyu; Xie, Shuhong; Liu, Xiaoyan

    2015-07-27

    Disordered carbons processed from polymers have much higher theoretical capacity as lithium ion battery anode than graphite, but they suffer from large irreversible capacity loss and have poor cyclic performance. Here, a simple process to obtain patterned carbon structure from polyvinylpyrrolidone was demonstrated, combining nanoimprint lithography for patterning and three-step heat treatment process for carbonization. The patterned carbon, without any additional binders or conductive fillers, shows remarkably improved cycling performance as Li-ion battery anode, twice as high as the theoretical value of graphite at 98 cycles. Localized electrochemical strain microscopy reveals the enhanced lithium ion activity at the nanoscale, and the control experiments suggest that the enhancement largely originates from the patterned structure, which improves surface reaction while it helps relieving the internal stress during lithium insertion and extraction. This study provides insight on fabricating patterned carbon architecture by rational design for enhanced electrochemical performance.

  20. Spinel electrodes for rechargeable lithium batteries.

    SciTech Connect

    Thackeray, M. M.

    1999-11-10

    This paper gives a historical account of the development of spinel electrodes for rechargeable lithium batteries. Research in the late 1970's and early 1980's on high-temperature . Li/Fe{sub 3}O{sub 4} cells led to the evaluation of lithium spinels Li[B{sub 2}]X{sub 4} at room temperature (B = metal cation). This work highlighted the importance of the [B{sub 2}]X{sub 4}spinel framework as a host electrode structure and the ability to tailor the cell voltage by selection of different B cations. Examples of lithium-ion cells that operate with spinel anode/spinel cathode couples are provided. Particular attention is paid to spinels within the solid solution system Li{sub 1+x}Mn{sub 2-x}O{sub 4} (0 {le} x {le} 0.33).

  1. Characterization of lithium phosphorous oxynitride thin films

    SciTech Connect

    Yu, Xiaohua; Bates, J.B.; Jellison, G.E. Jr.

    1996-01-01

    Electrical and electrochemical properties of an amorphous thin-film lithium electrolyte, lithium phosphorous oxynitride (Lipon), have been studied with emphasis on the stability window vs Li metal and the behavior of the Li/Lipon interface. Ion conductivity of Lipon exhibits Arrhenius behavior at {minus}26 to +140 C, with a conductivity of 1.7 {times} 10{sup {minus}6}S/cm at 25 C and an activity energy of 0.50 {plus_minus} 0.01 eV. A stability window of 5.5 V was observed with respect to a Li{sup +}/Li reference, and no detectable reaction or degradation was evident at the Li/Lipon interface upon lithium cycling.

  2. Determination of lithium in rocks by distillation

    USGS Publications Warehouse

    Fletcher, M.H.

    1949-01-01

    A method for the quantitative extraction and recovery of lithium from rocks is based on a high temperature volatilization procedure. The sample is sintered with a calcium carbonate-calcium chloride mixture at 1200?? C. for 30 minutes in a platinum ignition tube, and the volatilization product is collected in a plug of Pyrex glass wool in a connecting Pyrex tube. The distillate, which consists of the alkali chlorides with a maximum of 5 to 20 mg. of calcium oxide and traces of a few other elements, is removed from the apparatus by dissolving in dilute hydrochloric acid and subjected to standard analytiaal procedures. The sinter residues contained less than 0.0005% lithium oxide. Lithium oxide was recovered from synthetic samples with an average error of 1.1%.

  3. Safety considerations for fabricating lithium battery packs

    NASA Technical Reports Server (NTRS)

    Ciesla, J. J.

    1986-01-01

    Lithium cell safety is a major issue with both manufacturers and end users. Most manufacturers have taken great strides to develop the safest cells possible while still maintaining performance characteristics. The combining of lithium cells for higher voltages, currents, and capacities requires the fabricator of lithium battery packs to be knowledgable about the specific electrochemical system being used. Relatively high rate, spirally wound (large surface area) sulfur oxychloride cells systems, such as Li/Thionyl or Sulfuryl chloride are considered. Prior to the start of a design of a battery pack, a review of the characterization studies for the cells should be conducted. The approach for fabricating a battery pack might vary with cell size.

  4. Lithium-aluminum-magnesium electrode composition

    DOEpatents

    Melendres, Carlos A.; Siegel, Stanley

    1978-01-01

    A negative electrode composition is presented for use in a secondary, high-temperature electrochemical cell. The cell also includes a molten salt electrolyte of alkali metal halides or alkaline earth metal halides and a positive electrode including a chalcogen or a metal chalcogenide as the active electrode material. The negative electrode composition includes up to 50 atom percent lithium as the active electrode constituent and a magnesium-aluminum alloy as a structural matrix. Various binary and ternary intermetallic phases of lithium, magnesium, and aluminum are formed but the electrode composition in both its charged and discharged state remains substantially free of the alpha lithium-aluminum phase and exhibits good structural integrity.

  5. Lithium reprocessing technology for ceramic breeders

    NASA Astrophysics Data System (ADS)

    Tsuchiya, Kunihiko; Kawamura, Hiroshi; Saito, Minoru; Tatenuma, Katuyashi; Kainose, Mitsuru

    1995-03-01

    Lithium ceramics have been receiving considerable attention as tritium breeding materials for fusion reactors. Reprocessing technology development for these materials is proposed to recover lithium, as an effective use of resources and to remove radioactive isotopes. Four potential ceramic breeders (Li 2O, LiAlO 2, Li 2ZrO 3 and Li 4SiO 4) were prepared in order to estimate their dissolution properties in water and various acids (HCl, HNO 3, H 2SO 4, HF and aqua regia). The dissolution rates were determined by comparing the weight of the residue with that of the starting powder (the weight method). Recovery properties of lithium were examined by the precipitation method.

  6. Lithium Storage in Heat-Treated SnF2 /Polyacrylonitrile Anode.

    PubMed

    Shen, Lian; Shen, Lanyao; Wang, Zhaoxiang; Chen, Liquan

    2015-06-01

    Tin(II) fluoride (SnF2 ) has a high Li-storage capacity because it stores lithium first by a conversion reaction and then by a Li/Sn alloying/dealloying reaction. A polyacrylonitrile (PAN)-bound SnF2 electrode was heat-treated to enhance the integral electrical contact and the mechanical strength through its cross-linked framework. The heat-treated SnF2 electrode showed reversible capacities of 1047 mAh g(-1) in the first cycle and 902 mAh g(-1) after 100 cycles. Part of the excess capacity is due to lithium storage at the Sn/LiF interface, and the other part is assumed to correspond to the presence of reduced SnF2 with protons released during the thermal cross-linking of PAN. PMID:25925247

  7. Lithium metal reduction of plutonium oxide to produce plutonium metal

    DOEpatents

    Coops, Melvin S.

    1992-01-01

    A method is described for the chemical reduction of plutonium oxides to plutonium metal by the use of pure lithium metal. Lithium metal is used to reduce plutonium oxide to alpha plutonium metal (alpha-Pu). The lithium oxide by-product is reclaimed by sublimation and converted to the chloride salt, and after electrolysis, is removed as lithium metal. Zinc may be used as a solvent metal to improve thermodynamics of the reduction reaction at lower temperatures. Lithium metal reduction enables plutonium oxide reduction without the production of huge quantities of CaO--CaCl.sub.2 residues normally produced in conventional direct oxide reduction processes.

  8. Lithium Toxicity Following Vertical Sleeve Gastrectomy: A Case Report.

    PubMed

    Alam, Abdulkader; Raouf, Sherief; Recio, Fernando O

    2016-08-31

    We are presenting the first documented case of lithium toxicity after vertical sleeve gastrectomy surgery in an 18 year-old female with psychiatric history of bipolar disorder who was treated with lithium. This case illustrates the need for closer monitoring of lithium levels following bariatric surgery. Both psychiatrists and surgeons should be aware of the potential risk of lithium toxicity following bariatric surgery, as well as the need to judiciously monitor lithium level and possibly adjust the dose of some medications. PMID:27489390

  9. Lithium Toxicity Following Vertical Sleeve Gastrectomy: A Case Report

    PubMed Central

    Alam, Abdulkader; Raouf, Sherief; Recio, Fernando O.

    2016-01-01

    We are presenting the first documented case of lithium toxicity after vertical sleeve gastrectomy surgery in an 18 year-old female with psychiatric history of bipolar disorder who was treated with lithium. This case illustrates the need for closer monitoring of lithium levels following bariatric surgery. Both psychiatrists and surgeons should be aware of the potential risk of lithium toxicity following bariatric surgery, as well as the need to judiciously monitor lithium level and possibly adjust the dose of some medications. PMID:27489390

  10. Lithium oxides precipitation in nonaqueous Li-air batteries.

    PubMed

    Hou, Junbo; Yang, Min; Ellis, Michael W; Moore, Robert B; Yi, Baolian

    2012-10-21

    Lithium-air/oxygen battery is a rising star in the field of electrochemical energy storage as a promising alternative to lithium ion batteries. Nevertheless, this alluring system is still at its infant stage, and the breakthrough of lithium-air batteries into the energy market is currently constrained by a combination of scientific and technical challenges. Targeting at the air electrode in nonaqueous lithium-air batteries, this review attempts to summarize the knowledge about the fundamentals related to lithium oxides precipitation, which has been one of the vital and attractive aspects of the research communities of science and technology. PMID:22968061

  11. Brain Lithium Levels and Effects on Cognition and Mood in Geriatric Bipolar Disorder: A Lithium-7 Magnetic Resonance Spectroscopy Study

    PubMed Central

    Forester, Brent P.; Streeter, Chris C.; Berlow, Yosef A.; Tian, Hua; Wardrop, Megan; Finn, Chelsea T.; Harper, David; Renshaw, Perry F.; Moore, Constance M.

    2014-01-01

    Objectives The authors investigated the relationship between brain lithium, serum lithium and age in adult subjects treated with lithium. In addition, the authors investigated the association between brain lithium and serum lithium with frontal lobe functioning and mood in a subgroup of older subjects. Design Cross-sectional assessment. Setting McLean Hospital’s Geriatric Psychiatry Research Program and Brain Imaging Center; The Division of Psychiatry, Boston University School of Medicine. Participants Twenty-six subjects, 20 to 85 years, with Diagnostic and Statistical Manual of Mental Disorders, Fourth Edition–TR bipolar disorder (BD), currently treated with lithium. Measurements All subjects had measurements of mood (Hamilton Depression Rating Scale [HDRS] and Young Mania Rating Scale) and serum and brain lithium levels. Brain lithium levels were assessed using lithium Magnetic Resonance Spectroscopy. Ten subjects older than 50 years also had assessments of frontal lobe functioning (Stroop, Trails A and B, Wis. Card Sorting Task). Results Brain lithium levels correlated with serum lithium levels for the group as a whole. However, this relationship was not present for the group of subjects older than 50. For these older subjects elevations in brain (but not serum) lithium levels were associated with frontal lobe dysfunction and higher HDRS scores. The higher HDRS were associated with increased somatic symptoms. Conclusion Frontal lobe dysfunction and elevated depression symptoms correlating with higher brain lithium levels supports conservative dosing recommendations in bipolar older adults. The absence of a predictable relationship between serum and brain lithium makes specific individual predictions about the “ideal” lithium serum level in an older adult with BD difficult. PMID:18626002

  12. Cosmis Lithium-Beryllium-Boron Story

    NASA Astrophysics Data System (ADS)

    Vangioni-Flam, E.; Cassé, M.

    Light element nucleosynthesis is an important chapter of nuclear astrophysics. Specifically, the rare and fragile light nuclei Lithium, Beryllium and Boron (LiBeB) are not generated in the normal course of stellar nucleosynthesis (except Lithium-7) and are, in fact, destroyed in stellar interiors. This characteristic is reflected in the low abundance of these simple species. Up to recently, the most plausible interpretation was that galactic cosmic rays (GCR) interact with interstellar CNO to form LiBeB. Other origins have been also identified, primordial and stellar (Lithium-7) and supernova neutrino spallation (Lithium-7 and Boron-11). In contrast, Beryllium-9, Boron-10 and Lithium-6 are pure spallative products. This last isotope presents a special interest since the Lithium-7/Lithium-6 ratio has been measured in a few halo stars offering a new constraint on the early galactic evolution. However, in the nineties, new observations prompted astrophysicists to reassess the question. Optical measurements of the beryllium and boron abundances in halo stars have been achieved by the 10 meters KECK telescope and the Hubble Space Telescope. These observations indicate a quasi linear correlation between Be and B vs Fe, at least at low metallicity, unexpected on the basis of GCR scenario, predicting a quadratic relationship. As a consequence, the origin and the evolution of the LiBeB nuclei has been revisited. This linearity implies the acceleration of C and O nuclei freshly synthesized and their fragmentation on the the interstellar Hydrogen and Helium. Wolf-Rayet stars and supernovae via the shock waves induced, are the best candidates to the acceleration of their own material enriched into C and O; so LiBeB is produced independently of the Interstellar Medium chemical composition. Moreover, neutrinos emitted by the newly born neutron stars interacting with the C layer of the supernova could produce specifically Lithium-7 and Boron-11. This process is supported by the

  13. Hazards of lithium thionyl chloride batteries

    NASA Technical Reports Server (NTRS)

    Parry, J. M.

    1978-01-01

    Two different topics which only relate in that they are pertinent to lithium thionyl chloride battery safety are discussed. The first topic is a hazards analysis of a system (risk assessment), a formal approach that is used in nuclear engineering, predicting oil spills, etc. It is a formalized approach for obtaining assessment of the degree of risk associated with the use of any particular system. The second topic is a small piece of chemistry related to the explosions that can occur with lithium thionyl chloride systems. After the two topics are presented, a discussion is generated among the Workshop participants.

  14. Model potential calculations of lithium transitions.

    NASA Technical Reports Server (NTRS)

    Caves, T. C.; Dalgarno, A.

    1972-01-01

    Semi-empirical potentials are constructed that have eigenvalues close in magnitude to the binding energies of the valence electron in lithium. The potentials include the long range polarization force between the electron and the core. The corresponding eigenfunctions are used to calculate dynamic polarizabilities, discrete oscillator strengths, photoionization cross sections and radiative recombination coefficients. A consistent application of the theory imposes a modification on the transition operator, but its effects are small for lithium. The method presented can be regarded as a numerical generalization of the widely used Coulomb approximation.

  15. Electrolytes for high-energy lithium batteries

    NASA Astrophysics Data System (ADS)

    Schaefer, Jennifer L.; Lu, Yingying; Moganty, Surya S.; Agarwal, Praveen; Jayaprakash, N.; Archer, Lynden A.

    2012-06-01

    From aqueous liquid electrolytes for lithium-air cells to ionic liquid electrolytes that permit continuous, high-rate cycling of secondary batteries comprising metallic lithium anodes, we show that many of the key impediments to progress in developing next-generation batteries with high specific energies can be overcome with cleaver designs of the electrolyte. When these designs are coupled with as cleverly engineered electrode configurations that control chemical interactions between the electrolyte and electrode or by simple additives-based schemes for manipulating physical contact between the electrolyte and electrode, we further show that rechargeable battery configurations can be facilely designed to achieve desirable safety, energy density and cycling performance.

  16. Solid composite electrolytes for lithium batteries

    DOEpatents

    Kumar, Binod; Scanlon, Jr., Lawrence G.

    2001-01-01

    Solid composite electrolytes are provided for use in lithium batteries which exhibit moderate to high ionic conductivity at ambient temperatures and low activation energies. In one embodiment, a polymer-ceramic composite electrolyte containing poly(ethylene oxide), lithium tetrafluoroborate and titanium dioxide is provided in the form of an annealed film having a room temperature conductivity of from 10.sup.-5 S cm.sup.-1 to 10.sup.-3 S cm.sup.-1 and an activation energy of about 0.5 eV.

  17. Polarization Labeling Spectroscopy of Hollow Lithium

    NASA Astrophysics Data System (ADS)

    Huang, M.-T.; Wehlitz, R.; Cherepkov, N. A.; Azuma, Y.; Depaola, B. D.; Nagata, T.; Hasegawa, S.; Levin, J. C.; Sellin, I. A.

    1998-05-01

    Utilization of polarized or aligned targets can provide valuable information on atomic photoionization and excitation processes. (M. Meyer et al.), Phys. Rev. Lett. 59, 2963 (1987) We measured numerous even-parity doubly core excited ``hollow lithium'' resonances using monchromatized synchrotron radiation derived from an undulator, and laser excited lithium targets. The excited 1s^22p ^2Po targets, were aligned or polarized by laser pumping, and measurements were made with various combinations with the polarization of synchrotron radiation. The intensity pattern of the photoion spectrum shows clear polarization dependence and provides useful clues to the analysis.

  18. Electrolytic orthoborate salts for lithium batteries

    DOEpatents

    Angell, Charles Austen; Xu, Wu

    2008-01-01

    Orthoborate salts suitable for use as electrolytes in lithium batteries and methods for making the electrolyte salts are provided. The electrolytic salts have one of the formulae (I). In this formula anionic orthoborate groups are capped with two bidentate chelating groups, Y1 and Y2. Certain preferred chelating groups are dibasic acid residues, most preferably oxalyl, malonyl and succinyl, disulfonic acid residues, sulfoacetic acid residues and halo-substituted alkylenes. The salts are soluble in non-aqueous solvents and polymeric gels and are useful components of lithium batteries in electrochemical devices.

  19. Electrolytic orthoborate salts for lithium batteries

    DOEpatents

    Angell, Charles Austen [Mesa, AZ; Xu, Wu [Tempe, AZ

    2009-05-05

    Orthoborate salts suitable for use as electrolytes in lithium batteries and methods for making the electrolyte salts are provided. The electrolytic salts have one of the formulae (I). In this formula anionic orthoborate groups are capped with two bidentate chelating groups, Y1 and Y2. Certain preferred chelating groups are dibasic acid residues, most preferably oxalyl, malonyl and succinyl, disulfonic acid residues, sulfoacetic acid residues and halo-substituted alkylenes. The salts are soluble in non-aqueous solvents and polymeric gels and are useful components of lithium batteries in electrochemical devices.

  20. Properties of lead-lithium solutions

    SciTech Connect

    Hoffman, N.J.; Darnell, A.; Blink, J.A.

    1980-10-01

    Lead-lithium solutions are of interest to liquid metal wall ICF reactor designers because Pb may be present to some extent in both heavy ion beam and laser-driven ICF targets; therefore, Pb will be present as an impurity in a flowing lithium wall. In addition, Pb-Li solutions containing approx. 80 a/o Pb are a strong candidate for a heavy ion beam driven HYLIFE converter and a viable alternative to a pure Li wall for a laser driven converter. The properties of Pb-Li solutions including the effect of hydrogen impurities are reviewed, and the reactor design implications are discussed.

  1. Lithium batteries: Application of neutron radiography

    NASA Astrophysics Data System (ADS)

    Kamata, Masahiro; Esaka, Takao; Fujine, Shigenori; Yoneda, Kenji; Kanda, Keiji

    Several kinds of primary and secondary commercial lithium batteries, such as CR1/3 · 1H (Fujitsu), CR1220 and BR435 (Panasonic), ML1220 (Sanyo Excel) were investigated using neutron radiography; the variation of the lithium distribution inside these batteries upon discharging (and charging) were clarified by analyzing their visualized images. It was demonstrated that neutron radiography is a potential and useful method, especially in evaluating the reversibility of rechargeable batteries, which have been used under different discharging/charging conditions.

  2. Lithium intercalation in porous carbon anodes

    SciTech Connect

    Tran, T.D.; Pekala, R.W.; Mayer, S.T.

    1994-11-23

    Carbon foams derived from the phase separation of polyacrylonitrile/solvent mixtures were investigated as lithium intercalation anodes for rechargeable lithium-ion batteries. The carbon foams have a bulk density of 0.35--0.5 g/cm{sup 3}, low surface area (< 50 m{sup 2}/g), and an average cell size of 5--10 {mu}m. Polyacrylonitrile-based carbon foams doped with phosphoric acid had capacity as high as 450 mAh/g. Carbon capacity increased with increasing phosphoric acid concentration in the doping solution. The doped porous carbon anodes exhibited good cyclability and excellent coulombic efficiency.

  3. Brain oscillations in bipolar disorder and lithium-induced changes

    PubMed Central

    Atagün, Murat İlhan

    2016-01-01

    Electroencephalography (EEG) studies in patients with bipolar disorder have revealed lower amplitudes in brain oscillations. The aim of this review is to describe lithium-induced EEG changes in bipolar disorder and to discuss potential underlying factors. A literature survey about lithium-induced EEG changes in bipolar disorder was performed. Lithium consistently enhances magnitudes of brain oscillations in slow frequencies (delta and theta) in both resting-state EEG studies as well as event-related oscillations studies. Enhancement of magnitudes of beta oscillations is specific to event-related oscillations. Correlation between serum lithium levels and brain oscillations has been reported. Lithium-induced changes in brain oscillations might correspond to lithium-induced alterations in neurotransmitters, signaling cascades, plasticity, brain structure, or biophysical properties of lithium. Therefore, lithium-induced changes in brain oscillations could be promising biomarkers to assess the molecular mechanisms leading to variability in efficacy. Since the variability of lithium response in bipolar disorder is due to the genetic differences in the mechanisms involving lithium, it would be highly promising to assess the lithium-induced EEG changes as biomarkers in genetic studies. PMID:27022264

  4. Association of maternal lithium exposure and premature delivery.

    PubMed

    Troyer, W A; Pereira, G R; Lannon, R A; Belik, J; Yoder, M C

    1993-01-01

    Lithium is widely used and the treatment of choice for patients with manic-depressive illness. For pregnant patients with manic-depressive illness, however, the use of lithium during the first trimester of pregnancy may present an increased risk for fetal maldevelopment. We have recently cared for several large-for-gestational-age, prematurely born infants whose mothers were treated with lithium throughout pregnancy. To determine whether maternal lithium use during pregnancy may predispose to the onset of premature labor and fetal macrosomia, we reviewed records from the International Register of Lithium Babies and from a cohort of manic-depressive pregnant women. More than one third (36%) of infants reported to the International Register were born prematurely, and 37% of the premature infants were large for gestational age; 15% of the term infants were born large for gestational age. In the cohort group, manic-depressive mothers who received lithium during pregnancy had a 2.5-fold higher incidence of premature births than manic-depressive pregnant patients who did not receive lithium treatment. The incidence of large-for-gestational-age births in lithium-treated women in the cohort was not different from that of the general population or from manic-depressive women not treated with lithium. In summary, an association between maternal lithium therapy and premature delivery is reported. We recommend that women receiving lithium therapy during pregnancy be closely monitored for the onset of premature labor. PMID:8515304

  5. P1.2 -- Hybrid Electric Vehicle and Lithium Polymer NEV Testing

    SciTech Connect

    J. Francfort

    2006-06-01

    The U.S. Department of Energy’s Advanced Vehicle Testing Activity tests hybrid electric, pure electric, and other advanced technology vehicles. As part of this testing, 28 hybrid electric vehicles (HEV) are being tested in fleet, dynamometer, and closed track environments. This paper discusses some of the HEV test results, with an emphasis on the battery performance of the HEVs. It also discusses the testing results for a small electric vehicle with a lithium polymer traction battery.

  6. Modeling Lithium Ion Battery Safety: Venting of Pouch Cells; NREL (National Renewable Energy Laboratory)

    SciTech Connect

    Santhanagopalan, Shriram.; Yang, Chuanbo.; Pesaran, Ahmad

    2013-07-01

    This report documents the successful completion of the NREL July milestone entitled “Modeling Lithium-Ion Battery Safety - Complete Case-Studies on Pouch Cell Venting,” as part of the 2013 Vehicle Technologies Annual Operating Plan with the U.S. Department of Energy (DOE). This work aims to bridge the gap between materials modeling, usually carried out at the sub-continuum scale, and the

  7. Lithium toxicity after Roux-en-Y bariatric surgery.

    PubMed

    Musfeldt, Deanna; Levinson, Andrew; Nykiel, Jennifer; Carino, Gerardo

    2016-01-01

    A 61-year-old woman with medical history significant for morbid obesity, type II diabetes mellitus, nephrogenic diabetes insipidus and bipolar disorder, had been stable on lithium carbonate therapy for several years. She had undergone a Roux-en-Y bypass surgery and, at the time of her surgery, her lithium level was found to be 0.61 mEq/L on a maintenance dose of 600 mg orally twice per day. She was discharged 8 days postoperatively on the same lithium dose, but presented to the emergency department 12 days postoperatively with signs of lithium toxicity. Her lithium level was elevated to 1.51 mEq/L and she was treated for lithium toxicity with supportive care and, ultimately, reduction of her lithium dose. Clinicians should be aware that dramatic and poorly understood changes in drug absorption may occur after bariatric surgery. PMID:26994048

  8. Sinus Node Dysfunction After Acute Lithium Treatment at Therapeutic Levels

    PubMed Central

    Nakatsu, Keigo; Nagamine, Takahiko

    2015-01-01

    Lithium carbonate (lithium) has been used extensively for the treatment of a variety of psychiatric conditions. It requires close monitoring of serum concentration due to its narrow therapeutic window. Cardiac toxicity range from asymptomatic electrocardiographic changes to fatal arrhythmias may occur even at the therapeutic levels. We report a case of psychiatric inpatient who developed asymptomatic severe bradycardia most likely related to sinus node dysfunction due to acute lithium treatment at therapeutic level. After withdrawal of lithium, a time sequential improvement of severe bradycardia examined by repeated electrocardiogram, including Holter monitoring, suggested a relationship between the lithium toxicity and sinus node dysfunction. Other factors such as baseline sinus bradycardia and lower limit of normal thyroid function might be associated with severe bradycardia. This case emphasizes the need, when prescribing lithium, for clinicians to regularly monitor their patients’ electrocardiogram and serum lithium levels to prevent serious or fatal complications, such as cardiac arrest. PMID:27222761

  9. Lithium mass flow control for high power Lorentz Force Accelerators

    NASA Astrophysics Data System (ADS)

    Kodys, Andrea D.; Emsellem, Gregory; Cassady, Leonard D.; Polk, James E.; Choueiri, Edgar Y.

    2001-02-01

    A lithium feeding system has been developed to measure and control propellant flow for 30-200 kW Lithium Lorentz Force Accelerators (LiLFAs). The new, mechanically actuated, liquid lithium feed system has been designed and tested as a central component of a campaign to obtain basic data and establish scaling laws and performance relations for these thrusters. Calibration data are presented which demonstrate reliable and controllable feed of liquid lithium to the vaporizer hollow cathode of the thruster at flow rates between 10 and 120 mg/s. The ability to thermally track the liquid lithium through the system by the use of external temperature measurements is demonstrated. In addition, recent developments are presented in the establishment and successful testing of a lithium handling facility and safety procedures allowing for the in-house loading of the feed system and the neutralization, cleaning and disposal of up to 300 g of lithium. .

  10. Lithium Surface Coatings for Improved Plasma Performance in NSTX

    SciTech Connect

    Kugel, H W; Ahn, J -W; Allain, J P; Bell, R; Boedo, J; Bush, C; Gates, D; Gray, T; Kaye, S; Kaita, R; LeBlanc, B; Maingi, R; Majeski, R; Mansfield, D; Menard, J; Mueller, D; Ono, M; Paul, S; Raman, R; Roquemore, A L; Ross, P W; Sabbagh, S; Schneider, H; Skinner, C H; Soukhanovskii, V; Stevenson, T; Timberlake, J; Wampler, W R

    2008-02-19

    NSTX high-power divertor plasma experiments have shown, for the first time, significant and frequent benefits from lithium coatings applied to plasma facing components. Lithium pellet injection on NSTX introduced lithium pellets with masses 1 to 5 mg via He discharges. Lithium coatings have also been applied with an oven that directed a collimated stream of lithium vapor toward the graphite tiles of the lower center stack and divertor. Lithium depositions from a few mg to 1 g have been applied between discharges. Benefits from the lithium coating were sometimes, but not always seen. These improvements sometimes included decreases plasma density, inductive flux consumption, and ELM frequency, and increases in electron temperature, ion temperature, energy confinement and periods of MHD quiescence. In addition, reductions in lower divertor D, C, and O luminosity were measured.

  11. Lithium pellet production (LiPP): A device for the production of small spheres of lithium

    SciTech Connect

    Fiflis, P.; Andrucyzk, D.; McGuire, M.; Curreli, D.; Ruzic, D. N.; Roquemore, A. L.

    2013-06-15

    With lithium as a fusion material gaining popularity, a method for producing lithium pellets relatively quickly has been developed for NSTX. The Lithium Pellet Production device is based on an injector with a sub-millimeter diameter orifice and relies on a jet of liquid lithium breaking apart into small spheres via the Plateau-Rayleigh instability. A prototype device is presented in this paper and for a pressure difference of {Delta}P= 5 Torr, spheres with diameters between 0.91 < D < 1.37 mm have been produced with an average diameter of D= 1.14 mm, which agrees with the developed theory. Successive tests performed at Princeton Plasma Physics Laboratory with Wood's metal have confirmed the dependence of sphere diameter on pressure difference as predicted.

  12. Lithium pellet production (LiPP): A device for the production of small spheres of lithium

    NASA Astrophysics Data System (ADS)

    Fiflis, P.; Andrucyzk, D.; Roquemore, A. L.; McGuire, M.; Curreli, D.; Ruzic, D. N.

    2013-06-01

    With lithium as a fusion material gaining popularity, a method for producing lithium pellets relatively quickly has been developed for NSTX. The Lithium Pellet Production device is based on an injector with a sub-millimeter diameter orifice and relies on a jet of liquid lithium breaking apart into small spheres via the Plateau-Rayleigh instability. A prototype device is presented in this paper and for a pressure difference of ΔP = 5 Torr, spheres with diameters between 0.91 < D < 1.37 mm have been produced with an average diameter of D = 1.14 mm, which agrees with the developed theory. Successive tests performed at Princeton Plasma Physics Laboratory with Wood's metal have confirmed the dependence of sphere diameter on pressure difference as predicted.

  13. Nanostructured lithium-aluminum alloy electrodes for lithium-ion batteries.

    SciTech Connect

    Hudak, Nicholas S.; Huber, Dale L.

    2010-12-01

    Electrodeposited aluminum films and template-synthesized aluminum nanorods are examined as negative electrodes for lithium-ion batteries. The lithium-aluminum alloying reaction is observed electrochemically with cyclic voltammetry and galvanostatic cycling in lithium half-cells. The electrodeposition reaction is shown to have high faradaic efficiency, and electrodeposited aluminum films reach theoretical capacity for the formation of LiAl (1 Ah/g). The performance of electrodeposited aluminum films is dependent on film thickness, with thicker films exhibiting better cycling behavior. The same trend is shown for electron-beam deposited aluminum films, suggesting that aluminum film thickness is the major determinant in electrochemical performance regardless of deposition technique. Synthesis of aluminum nanorod arrays on stainless steel substrates is demonstrated using electrodeposition into anodic aluminum oxide templates followed by template dissolution. Unlike nanostructures of other lithium-alloying materials, the electrochemical performance of these aluminum nanorod arrays is worse than that of bulk aluminum.

  14. Lithium storage mechanisms in purpurin based organic lithium ion battery electrodes

    PubMed Central

    Reddy, Arava Leela Mohana; Nagarajan, Subbiah; Chumyim, Porramate; Gowda, Sanketh R.; Pradhan, Padmanava; Jadhav, Swapnil R.; Dubey, Madan; John, George; Ajayan, Pulickel M.

    2012-01-01

    Current lithium batteries operate on inorganic insertion compounds to power a diverse range of applications, but recently there is a surging demand to develop environmentally friendly green electrode materials. To develop sustainable and eco-friendly lithium ion batteries, we report reversible lithium ion storage properties of a naturally occurring and abundant organic compound purpurin, which is non-toxic and derived from the plant madder. The carbonyl/hydroxyl groups present in purpurin molecules act as redox centers and reacts electrochemically with Li-ions during the charge/discharge process. The mechanism of lithiation of purpurin is fully elucidated using NMR, UV and FTIR spectral studies. The formation of the most favored six membered binding core of lithium ion with carbonyl groups of purpurin and hydroxyl groups at C-1 and C-4 positions respectively facilitated lithiation process, whereas hydroxyl group at C-2 position remains unaltered. PMID:23233879

  15. Lithium Polysulfidophosphates: A Family of Lithium-Conducting Sulfur-Rich Compounds for Lithium-Sulfur Batteries

    SciTech Connect

    Lin, Zhan; Liu, Zengcai; Fu, Wujun; Dudney, Nancy J; Liang, Chengdu

    2013-01-01

    Given the great potential for improving the energy density of state-of-the-art lithium-ion batteries by a factor of 5, a breakthrough in lithium-sulfur (Li-S) batteries will have a dramatic impact in a broad scope of energy related fields. Conventional Li-S batteries that use liquid electrolytes are intrinsically short-lived with low energy efficiency. The challenges stem from the poor electronic and ionic conductivities of elemental sulfur and its discharge products. We report herein lithium polysulfidophosphates (LPSP), a family of sulfur-rich compounds, as the enabler of long-lasting and energy-efficient Li-S batteries. LPSP have ionic conductivities of 3.0 10-5 S cm-1 at 25 oC, which is 8 orders of magnitude higher than that of Li2S (~10-13 S cm-1). The high Li-ion conductivity of LPSP is the salient characteristic of these compounds that impart the excellent cycling performance to Li-S batteries. In addition, the batteries are configured in an all-solid state that promises the safe cycling of high-energy batteries with metallic lithium anodes.

  16. 77 FR 28488 - Outbound International Mailings of Lithium Batteries and Other Dangerous Goods

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-05-15

    ... accordance with additional requirements listed in the Technical Instructions. Lithium-ion cells and lithium... for mailpieces containing lithium metal or lithium-ion cells or batteries and applies regardless of... lithium-ion cells and batteries (rechargeable), regardless of quantity, size, watt hours, and...

  17. Review of lithium effects on brain and blood.

    PubMed

    Young, Wise

    2009-01-01

    Clinicians have long used lithium to treat manic depression. They have also observed that lithium causes granulocytosis and lymphopenia while it enhances immunological activities of monocytes and lymphocytes. In fact, clinicians have long used lithium to treat granulocytopenia resulting from radiation and chemotherapy, to boost immunoglobulins after vaccination, and to enhance natural killer activity. Recent studies revealed a mechanism that ties together these disparate effects of lithium. Lithium acts through multiple pathways to inhibit glycogen synthetase kinase-3beta (GSK3 beta). This enzyme phosphorylates and inhibits nuclear factors that turn on cell growth and protection programs, including the nuclear factor of activated T cells (NFAT) and WNT/beta-catenin. In animals, lithium upregulates neurotrophins, including brain-derived neurotrophic factor (BDNF), nerve growth factor, neurotrophin-3 (NT3), as well as receptors to these growth factors in brain. Lithium also stimulates proliferation of stem cells, including bone marrow and neural stem cells in the subventricular zone, striatum, and forebrain. The stimulation of endogenous neural stem cells may explain why lithium increases brain cell density and volume in patients with bipolar disorders. Lithium also increases brain concentrations of the neuronal markers n-acetyl-aspartate and myoinositol. Lithium also remarkably protects neurons against glutamate, seizures, and apoptosis due to a wide variety of neurotoxins. The effective dose range for lithium is 0.6-1.0 mM in serum and >1.5 mM may be toxic. Serum lithium levels of 1.5-2.0 mM may have mild and reversible toxic effects on kidney, liver, heart, and glands. Serum levels of >2 mM may be associated with neurological symptoms, including cerebellar dysfunction. Prolonged lithium intoxication >2 mM can cause permanent brain damage. Lithium has low mutagenic and carcinogenic risk. Lithium is still the most effective therapy for depression. It "cures" a third

  18. Reaction between Lithium Anode and Polysulfide Ions in a Lithium-Sulfur Battery.

    PubMed

    Zheng, Dong; Yang, Xiao-Qing; Qu, Deyang

    2016-09-01

    The reaction between polysulfides and a lithium anode in a Li-S battery was examined using HPLC. The results demonstrated that the polysulfide species with six sulfur atoms or more were reactive with regard to lithium metal. Although the reaction can be greatly inhibited by the addition of LiNO3 in the electrolyte, LiNO3 cannot form a stable protection layer on the Li anode to prevent the reaction during storage. PMID:27535337

  19. Lithium-Ion Performance and Abuse Evaluation Using Lithium Technologies 9Ah cell

    NASA Technical Reports Server (NTRS)

    Hall, Albert Daniel; Jeevarajan, Judith A.

    2006-01-01

    Lithium-ion batteries in a pouch form offer high energy density and safety in their designs and more recently they are offering performance at higher rates. Lithium Technologies 9Ah high-power pouch cells were studied at different rates, thermal environments, under vacuum and several different conditions of abuse including overcharge, over-discharge and external short circuit. Results of this study will be presented.

  20. Lanthanum Nitrate As Electrolyte Additive To Stabilize the Surface Morphology of Lithium Anode for Lithium-Sulfur Battery.

    PubMed

    Liu, Sheng; Li, Guo-Ran; Gao, Xue-Ping

    2016-03-01

    Lithium-sulfur (Li-S) battery is regarded as one of the most promising candidates beyond conventional lithium ion batteries. However, the instability of the metallic lithium anode during lithium electrochemical dissolution/deposition is still a major barrier for the practical application of Li-S battery. In this work, lanthanum nitrate, as electrolyte additive, is introduced into Li-S battery to stabilize the surface of lithium anode. By introducing lanthanum nitrate into electrolyte, a composite passivation film of lanthanum/lithium sulfides can be formed on metallic lithium anode, which is beneficial to decrease the reducibility of metallic lithium and slow down the electrochemical dissolution/deposition reaction on lithium anode for stabilizing the surface morphology of metallic Li anode in lithium-sulfur battery. Meanwhile, the cycle stability of the fabricated Li-S cell is improved by introducing lanthanum nitrate into electrolyte. Apparently, lanthanum nitrate is an effective additive for the protection of lithium anode and the cycling stability of Li-S battery. PMID:26981849

  1. Lithium increases proliferation of hippocampal neural stem/progenitor cells and rescues irradiation-induced cell cycle arrest in vitro.

    PubMed

    Zanni, Giulia; Di Martino, Elena; Omelyanenko, Anna; Andäng, Michael; Delle, Ulla; Elmroth, Kecke; Blomgren, Klas

    2015-11-10

    Radiotherapy in children causes debilitating cognitive decline, partly linked to impaired neurogenesis. Irradiation targets primarily cancer cells but also endogenous neural stem/progenitor cells (NSPCs) leading to cell death or cell cycle arrest. Here we evaluated the effects of lithium on proliferation, cell cycle and DNA damage after irradiation of young NSPCs in vitro.NSPCs were treated with 1 or 3 mM LiCl and we investigated proliferation capacity (neurosphere volume and bromodeoxyuridine (BrdU) incorporation). Using flow cytometry, we analysed apoptosis (annexin V), cell cycle (propidium iodide) and DNA damage (γH2AX) after irradiation (3.5 Gy) of lithium-treated NSPCs.Lithium increased BrdU incorporation and, dose-dependently, the number of cells in replicative phase as well as neurosphere growth. Irradiation induced cell cycle arrest in G1 and G2/M phases. Treatment with 3 mM LiCl was sufficient to increase NSPCs in S phase, boost neurosphere growth and reduce DNA damage. Lithium did not affect the levels of apoptosis, suggesting that it does not rescue NSPCs committed to apoptosis due to accumulated DNA damage.Lithium is a very promising candidate for protection of the juvenile brain from radiotherapy and for its potential to thereby improve the quality of life for those children who survive their cancer. PMID:26397227

  2. Lithium increases proliferation of hippocampal neural stem/progenitor cells and rescues irradiation-induced cell cycle arrest in vitro

    PubMed Central

    Omelyanenko, Anna; Andäng, Michael; Delle, Ulla; Elmroth, Kecke; Blomgren, Klas

    2015-01-01

    Radiotherapy in children causes debilitating cognitive decline, partly linked to impaired neurogenesis. Irradiation targets primarily cancer cells but also endogenous neural stem/progenitor cells (NSPCs) leading to cell death or cell cycle arrest. Here we evaluated the effects of lithium on proliferation, cell cycle and DNA damage after irradiation of young NSPCs in vitro. NSPCs were treated with 1 or 3 mM LiCl and we investigated proliferation capacity (neurosphere volume and bromodeoxyuridine (BrdU) incorporation). Using flow cytometry, we analysed apoptosis (annexin V), cell cycle (propidium iodide) and DNA damage (γH2AX) after irradiation (3.5 Gy) of lithium-treated NSPCs. Lithium increased BrdU incorporation and, dose-dependently, the number of cells in replicative phase as well as neurosphere growth. Irradiation induced cell cycle arrest in G1 and G2/M phases. Treatment with 3 mM LiCl was sufficient to increase NSPCs in S phase, boost neurosphere growth and reduce DNA damage. Lithium did not affect the levels of apoptosis, suggesting that it does not rescue NSPCs committed to apoptosis due to accumulated DNA damage. Lithium is a very promising candidate for protection of the juvenile brain from radiotherapy and for its potential to thereby improve the quality of life for those children who survive their cancer. PMID:26397227

  3. Hybrid Lithium-Sulfur Batteries with a Solid Electrolyte Membrane and Lithium Polysulfide Catholyte.

    PubMed

    Yu, Xingwen; Bi, Zhonghe; Zhao, Feng; Manthiram, Arumugam

    2015-08-01

    Lithium-sulfur (Li-S) batteries are receiving great attention as the most promising next-generation power source with significantly high charge-storage capacity. However, the implementation of Li-S batteries is hampered by a critical challenge because of the soluble nature of the intermediate polysulfide species in the liquid electrolyte. The use of traditional porous separators unavoidably allows the migration of the dissolved polysulfide species from the cathode to the lithium-metal anode and results in continuous loss of capacity. In this study, a LiSICON (lithium super ionic conductor) solid membrane is used as a cation-selective electrolyte for lithium-polysulfide (Li-PS) batteries to suppress the polysulfide diffusion. Ionic conductivity issue at the lithium metal/solid electrolyte interface is successfully addressed by insertion of a "soft", liquid-electrolyte integrated polypropylene interlayer. The solid LiSICON lithium-ion conductor maintains stable ionic conductivity during the electrochemical cycling of the cells. The Li-PS battery system with a hybrid solid/liquid electrolyte exhibits significantly enhanced cyclability relative to the cells with the traditional liquid-electrolyte integrated porous separator. PMID:26161547

  4. A review of lithium and non-lithium based solid state batteries

    NASA Astrophysics Data System (ADS)

    Kim, Joo Gon; Son, Byungrak; Mukherjee, Santanu; Schuppert, Nicholas; Bates, Alex; Kwon, Osung; Choi, Moon Jong; Chung, Hyun Yeol; Park, Sam

    2015-05-01

    Conventional lithium-ion liquid-electrolyte batteries are widely used in portable electronic equipment such as laptop computers, cell phones, and electric vehicles; however, they have several drawbacks, including expensive sealing agents and inherent hazards of fire and leakages. All solid state batteries utilize solid state electrolytes to overcome the safety issues of liquid electrolytes. Drawbacks for all-solid state lithium-ion batteries include high resistance at ambient temperatures and design intricacies. This paper is a comprehensive review of all aspects of solid state batteries: their design, the materials used, and a detailed literature review of various important advances made in research. The paper exhaustively studies lithium based solid state batteries, as they are the most prevalent, but also considers non-lithium based systems. Non-lithium based solid state batteries are attaining widespread commercial applications, as are also lithium based polymeric solid state electrolytes. Tabular representations and schematic diagrams are provided to underscore the unique characteristics of solid state batteries and their capacity to occupy a niche in the alternative energy sector.

  5. Robust recursive impedance estimation for automotive lithium-ion batteries

    NASA Astrophysics Data System (ADS)

    Fridholm, Björn; Wik, Torsten; Nilsson, Magnus

    2016-02-01

    Recursive algorithms, such as recursive least squares (RLS) or Kalman filters, are commonly used in battery management systems to estimate the electrical impedance of the battery cell. However, these algorithms can in some cases run into problems with bias and even divergence of the estimates. This article illuminates problems that can arise in the online estimation using recursive methods, and lists modifications to handle these issues. An algorithm is also proposed that estimates the impedance by separating the problem in two parts; one estimating the ohmic resistance with an RLS approach, and another one where the dynamic effects are estimated using an adaptive Kalman filter (AKF) that is novel in the battery field. The algorithm produces robust estimates of ohmic resistance and time constant of the battery cell in closed loop with SoC estimation, as demonstrated by both in simulations and with experimental data from a lithium-ion battery cell.

  6. Effect of lithium on behavioral disinhibition induced by electrolytic lesion of the median raphe nucleus

    PubMed Central

    Pezzato, Fernanda A.; Can, Adem; Hoshino, Katsumasa; Horta, José de Anchieta C.; Mijares, Miriam G.

    2014-01-01

    Rationale Alterations in brainstem circuits have been proposed as a possible mechanism underlying the etiology of mood disorders. Projections from the median raphe nucleus (MnR) modulate dopaminergic activity in the forebrain and are also part of a behavioral disinhibition/inhibition system that produces phenotypes resembling behavioral variations manifested during manic and depressive phases of bipolar disorder. Objective Assess the effect of chronic lithium treatment on behavioral disinhibition induced by MnR lesions. Methods MnR electrolytic lesions were performed in C57BL/6J mice, with sham operated and intact animals as control groups. Following recovery, mice were chronically treated with lithium (LiCl, added in chow) followed by behavioral testing. Results MnR lesion induced manic-like behavioral alterations including hyperactivity in the open field (OF), stereotyped circling, anxiolytic/risk taking in the elevated plus maze (EPM) and light/dark box (LDB) tests, and increased basal body temperature. Lithium was specifically effective in reducing OF hyperactivity and stereotypy but did not reverse (EPM) or had a nonspecific effect (LDB) on anxiety/risk taking measures. Additionally, lithium decreased saccharin preference and prevented weight loss during single housing. Conclusions Our data support electrolytic lesions of the MnR as an experimental model of a hyper-excitable/disinhibited phenotype consistent with some aspects of mania that are attenuated by the mood stabilizer lithium. Given lithium’s relatively specific efficacy in treating mania, these data support the hypothesis that manic symptoms derive not only from the stimulation of excitatory systems but also from inactivation or decreased activity of inhibitory mechanisms. PMID:25345734

  7. Electrohydrodynamic ion emission from molten lithium nitrate

    SciTech Connect

    Panitz, J.A.; Pregenzer, A.L.; Gerber, R.A.

    1989-01-01

    Positive ions have been generated at the surface of molten lithium nitrate by applying a high electrostatic field to a thin layer of the molten salt on the apex of a field emitter tip. The ion emission process is characteristic of electrohydrodynamic ion formation, usually observed when a high electric field is applied to the surface of a liquid metal or alloy. With molten lithium nitrate, a single emission site appears at threshold. The divergence of the ion beam is several degrees. At higher field strengths multiple emission sites are observed. An ion species at m/e = 76 amu dominates the mass spectrum at all field strengths. This species is identified as a cluster ion (LiNO/sub 3/ )Li/sup +/ . At low source temperatures, (LiNO/sub 3/ )/sub 2/ Li/sup +/ is also observed. Despite the low ionization potential of lithium (5.4 eV), Li/sup +/ accounts for <8% of the total ion current generated by the source under all operating conditions. Multiply charged lithium is not detected in the mass spectra, suggesting the electric field at the Taylor cone apex is not sufficient to field-ionize singly charged species by a postionization process.

  8. Stabilizing the surface of lithium metal

    SciTech Connect

    Vaughey, J. T.; Liu, Gao; Zhang, Ji-Guang

    2014-05-01

    Lithium metal is an ideal anode for the next generation of high capacity rechargeable batteries, including Li-air, Li-S, and other Li-based batteries using intercalation compounds. To enable the broad applications for lithium anodes, more fundamental studies need to be conducted to simultaneously address the two barriers discussed above. One of the key breakthroughs in this field may come from the development of new electrolytes (and additives) which can form a stable SEI layer with enough mechanical strength and flexibility. The ideal electrolyte may consist of only two components; one component inhibits dendrite growth, while another component forms a stable SEI layer to improve Coulombic efficiency. In this review, the status of three approaches at manipulating and controlling the lithium metal – electrolyte interface were discussed. While previous studies concentrated on coatings with minimal surface connectivity, the approaches discussed, namely a coating that forms and dissipates into the electrolyte based on charge density, a coating bonded to the termination layer of lithium, and a conformal carbonate coating formed at the interface, all highlight new research directions. Although there are still many obstacles to be overcome, we are optimistic that Li metal can be used as an anode in rechargeable batteries in the foreseeable future. This will enable wide

  9. Thin-film Rechargeable Lithium Batteries

    DOE R&D Accomplishments Database

    Bates, J. B.; Gruzalski, G. R.; Dudney, N. J.; Luck, C. F.; Yu, X.

    1993-11-01

    Rechargeable thin films batteries with lithium metal anodes, an amorphous inorganic electrolyte, and cathodes of lithium intercalation compounds have been fabricated and characterized. The cathodes include TiS{sub 2}, the {omega} phase of V{sub 2}O{sub 5}, and the cubic spinel Li{sub x}Mn{sub 2}O{sub 4} with open circuit voltages at full charge of about 2.5 V, 3.7 V, and 4.2 V, respectively. The development of these robust cells, which can be cycled thousands of times, was possible because of the stability of the amorphous lithium electrolyte, lithium phosphorus oxynitride. This material has a typical composition of Li{sub 2.9}PO{sub 3.3}N{sub 0.46} and a conductivity at 25 C of 2 {mu}S/cm. Thin film cells have been cycled at 100% depth of discharge using current densities of 2 to 100 {mu}A/cm{sup 2}. The polarization resistance of the cells is due to the slow insertion rate of Li{sup +} ions into the cathode. Chemical diffusion coefficients for Li{sup +} ions in the three types of cathodes have been estimated from the analysis of ac impedance measurements.

  10. Design considerations for rechargeable lithium batteries

    NASA Technical Reports Server (NTRS)

    Shen, D. H.; Huang, C.-K.; Davies, E.; Perrone, D.; Surampudi, S.; Halpert, Gerald

    1993-01-01

    Viewgraphs of a discussion of design considerations for rechargable lithium batteries. The objective is to determine the influence of cell design parameters on the performance of Li-TiS2 cells. Topics covered include cell baseline design and testing, cell design and testing, cell design parameters studies, and cell cycling performance.

  11. Performance and Safety of Lithium Ion Cells

    NASA Technical Reports Server (NTRS)

    Ratnakumar, B. V.; Smart, M. C.; Whitcanack, L.; Surampudi, S.; Marsh, R.

    2001-01-01

    This report evaluates the performance and safety of Lithium Ion (Li-Ion) cells when used in batteries. Issues discussed include the cycle life, energy efficiency, tolerance to higher charge voltage, tolerance to extended tapered charge voltage, charge on cycling, specific energy, low temperature discharge, low temperature charge, various charge characteristics, storage characteristics, and more of Li-Ion cells.

  12. Overview of ENEA's Projects on lithium batteries

    NASA Astrophysics Data System (ADS)

    Alessandrini, F.; Conte, M.; Passerini, S.; Prosini, P. P.

    The increasing need of high performance batteries in various small-scale and large-scale applications (portable electronics, notebooks, palmtops, cellular phones, electric vehicles, UPS, load levelling) in Italy is motivating the R&D efforts of various public and private organizations. Research of lithium batteries in Italy goes back to the beginning of the technological development of primary and secondary lithium systems with national know-how spread in various academic and public institutions with a few private stakeholders. In the field of lithium polymer batteries, ENEA has been dedicating significant efforts in almost two decades to promote and carry out basic R&D and pre-industrial development projects. In recent years, three major national projects have been performed and coordinated by ENEA in co-operation with some universities, governmental research organizations and industry. In these projects novel polymer electrolytes with ceramic additives, low cost manganese oxide-based composite cathodes, environmentally friendly process for polymer electrolyte, fabrication processes of components and cells have been investigated and developed in order to fulfill long-term needs of cost-effective and highly performant lithium polymer batteries.

  13. Silicon solar cells improved by lithium doping

    NASA Technical Reports Server (NTRS)

    Berman, P. A.

    1970-01-01

    Results of conference on characteristics of lithium-doped silicon solar cells and techniques required for fabrication indicate that output of cells has been improved to point where cells exhibit radiation resistance superior to those currently in use, and greater control and reproducibility of cell processing have been achieved.

  14. Stabilization of tokamak plasma by lithium streams

    SciTech Connect

    L.E. Zakharov

    2000-08-07

    The stabilization theory of free-boundary magnetohydrodynamic instabilities in tokamaks by liquid lithium streams driven by magnetic propulsion is formulated. While the conventional, wall-locked, resistive wall mode can be well suppressed by the flow, a new, stream-locked mode determines the limits of the flow stabilization.

  15. Lithium depletion and the star age connection

    NASA Astrophysics Data System (ADS)

    Carlos, Marília Gabriela C. C.

    2015-12-01

    It is known that lithium is destroyed in the inner layers of a star via proton capture ( 7Li(p, α)α) at temperatures near to 2.5 ∗ 106 K. Due to the fact that Li burning happens when the element is transported to the innermost and hotter regions through convective motions of the star, Li abundance studies offers an excellent opportunity to understand the extent of the mixing processes within and below the stellar convective zone. Thus, for a better understanding of the inner stars regions, this study aims to observe correlations between lithium abundances, stellar age, masses and planets occurrence for various solar twins aged between 0.7 and 8.8 Gyr.The sample consists of 21 solar twins measured in the HARPS spectrograph with spectral resolution R≈115.000 and signal to noise ratio from 400 to 2400. The lithium abundance were obtained by spectral synthesis of the line 6707.75 Å with the aid of MOOG code.The results indicate a strong correlation between age and Li abundances in the stars of this sample and a non-connection between lithium abundances and the presence of planets.

  16. Mineral resource of the month: lithium

    USGS Publications Warehouse

    Ober, Joyce A.

    2006-01-01

    Lithium, the lightest metallic element, is silvery, white and soft, and highly reactive. It is used most frequently in chemical compounds or traded as mineral concentrates. Its thermal properties make it an ideal component in thermal shock-resistant ceramics, and its electrochemical properties make it an ideal material for several types of batteries.

  17. Ionic liquids for rechargeable lithium batteries

    SciTech Connect

    Salminen, Justin; Papaiconomou, Nicolas; Kerr, John; Prausnitz,John; Newman, John

    2005-09-29

    We have investigated possible anticipated advantages of ionic-liquid electrolytes for use in lithium-ion batteries. Thermal stabilities and phase behavior were studied by thermal gravimetric analysis and differential scanning calorimetry. The ionic liquids studied include various imidazoliumTFSI systems, pyrrolidiniumTFSI, BMIMPF{sub 6}, BMIMBF{sub 4}, and BMIMTf. Thermal stabilities were measured for neat ionic liquids and for BMIMBF{sub 4}-LiBF{sub 4}, BMIMTf-LiTf, BMIMTFSI-LiTFSI mixtures. Conductivities have been measured for various ionic-liquid lithium-salt systems. We show the development of interfacial impedance in a Li|BMIMBF{sub 4} + LiBF{sub 4}|Li cell and we report results from cycling experiments for a Li|BMIMBF{sub 4} + 1 mol/kg LIBF{sub 4}|C cell. The interfacial resistance increases with time and the ionic liquid reacts with the lithium electrode. As expected, imidazolium-based ionic liquids react with lithium electrodes. We seek new ionic liquids that have better chemical stabilities.

  18. High-Cycle-Life Lithium Cell

    NASA Technical Reports Server (NTRS)

    Yen, S. P. S.; Carter, B.; Shen, D.; Somoano, R.

    1985-01-01

    Lithium-anode electrochemical cell offers increased number of charge/ discharge cycles. Cell uses components selected for compatibility with electrolyte solvent: These materials are wettable and chemically stable. Low vapor pressure and high electrochemical stability of solvent improve cell packaging, handling, and safety. Cell operates at modest temperatures - less than 100 degrees C - and is well suited to automotive, communications, and other applications.

  19. Synthesis and characterization of lithium ion batteries

    NASA Astrophysics Data System (ADS)

    Pradhan, A. K.; Zhang, K.; Mundle, R.; Arslan, M.; Amponsah, O.; Bahoura, M.

    2012-04-01

    Layered lithiated transition metal oxides have been extensively developed and investigated as a cathode materials for lithium ion batteries due to the following advantages, such as high output voltage of 3.6 V, high energy density larger than 450Wh/dm3, low self-discharge rate less than 10%, no memory effect resulting in long cycle lives for more than 1000 times charging and discharging, free maintenance and no environmental pollution. The cathode materials in lithium ion battery are generally in the form of LiMO2 (M= Co, Ni, Mn, etc). Currently, lithium vanadium oxides also were studied. It is well known that the synthetic condition and methods are closely related to the electrochemical properties of lithium ion batteries. In this work, the wet chemical sol gel techniques have been used to synthesize LiNiO2 and LiV3O8. In this study, the LiNiO2 particles and LiV3O8 nanorods were successfully synthesized by sol-gel wet chemical methods. Annealing heat treatment influence the crystallinity of the final product, which may be consequently affected their electrochemical performance.

  20. Electrostatic spray deposition based lithium ion capacitor

    NASA Astrophysics Data System (ADS)

    Agrawal, Richa; Chen, Chunhui; Wang, Chunlei

    2016-05-01

    Conventional Electrochemical double-layer capacitors (EDLCs) are well suited as power devices that can provide large bursts of energy in short time periods. However, their relatively inferior energy densities as compared to their secondary battery counterparts limit their application in devices that require simultaneous supply of both high energy and high power. In the wake of addressing this shortcoming of EDLCs, the concept of hybridization of lithium-ion batteries (LIBs) and EDLCs has attracted significant scientific interest in recent years. Such a device, generally referred to as the "lithium-ion capacitor" typically utilizes a lithium intercalating electrode along with a fast charging capacitor electrode. Herein we have constructed a lithium hybrid electrochemical capacitor comprising a Li4Ti5O12-TiO2 (LTO-TiO2) anode and a reduced graphene oxide and carbon nanotube (rGO-CNT) composite cathode using electrostatic spray deposition (ESD). The electrodes were characterized using scanning electron microscopy and X-ray diffraction studies. Cyclic voltammetry and galvanostatic charge-discharge measurements were carried out to evaluate the electrochemical performance of the individual electrodes and the full hybrid cells.

  1. Metallic lithium by quantum Monte Carlo

    SciTech Connect

    Sugiyama, G.; Zerah, G.; Alder, B.J.

    1986-12-01

    Lithium was chosen as the simplest known metal for the first application of quantum Monte Carlo methods in order to evaluate the accuracy of conventional one-electron band theories. Lithium has been extensively studied using such techniques. Band theory calculations have certain limitations in general and specifically in their application to lithium. Results depend on such factors as charge shape approximations (muffin tins), pseudopotentials (a special problem for lithium where the lack of rho core states requires a strong pseudopotential), and the form and parameters chosen for the exchange potential. The calculations are all one-electron methods in which the correlation effects are included in an ad hoc manner. This approximation may be particularly poor in the high compression regime, where the core states become delocalized. Furthermore, band theory provides only self-consistent results rather than strict limits on the energies. The quantum Monte Carlo method is a totally different technique using a many-body rather than a mean field approach which yields an upper bound on the energies. 18 refs., 4 figs., 1 tab.

  2. Determination of lithium in rocks: Fluorometric method

    USGS Publications Warehouse

    White, C.E.; Fletcher, M.H.; Parks, J.

    1951-01-01

    The gravimetric method in general use for the determination of lithium is tedious, and the final weighed product often contains other alkali metals. A fluorometric method was developed to shorten the time required for the analysis and to assure that the final determination is for lithium alone. This procedure is based on the complex formed between lithium and 8-hydroxyquinoline. The fluorescence is developed in a slightly alkaline solution of 95% alcohol and measurement is made on a photoelectric fluorometer. Separation from the ore is carried out by the wet method or by the distillation procedure. Sodium and potassium are removed by alcohol and ether, but complete separation is not necessary. Comparison of analyzed samples shows excellent agreement with spectrographic and gravimetric methods. The fluorometric method is more rapid than the gravimetric and produces more conclusive results. Another useful application is in the preparation of standard lithium solutions from reagent quality salts when a known standard is available. In this case no separations are necessary.

  3. Electrothermal Analysis of Lithium Ion Batteries

    SciTech Connect

    Pesaran, A.; Vlahinos, A.; Bharathan, D.; Duong, T.

    2006-03-01

    This report presents the electrothermal analysis and testing of lithium ion battery performance. The objectives of this report are to: (1) develop an electrothermal process/model for predicting thermal performance of real battery cells and modules; and (2) use the electrothermal model to evaluate various designs to improve battery thermal performance.

  4. Dendrites Inhibition in Rechargeable Lithium Metal Batteries

    NASA Astrophysics Data System (ADS)

    Aryanfar, Asghar

    The specific high energy and power capacities of rechargeable lithium metal (Li0) batteries are ideally suited to portable devices and are valuable as storage units for intermittent renewable energy sources. Lithium, the lightest and most electropositive metal, would be the optimal anode material for rechargeable batteries if it were not for the fact that such devices fail unexpectedly by short-circuiting via the dendrites that grow across electrodes upon recharging. This phenomenon poses a major safety issue because it triggers a series of adverse events that start with overheating, potentially followed by the thermal decomposition and ultimately the ignition of the organic solvents used in such devices. In this thesis, we developed experimental platform for monitoring and quantifying the dendrite populations grown in a Li battery prototype upon charging under various conditions. We explored the effects of pulse charging in the kHz range and temperature on dendrite growth, and also on loss capacity into detached "dead" lithium particles. Simultaneously, we developed a computational framework for understanding the dynamics of dendrite propagation. The coarse-grained Monte Carlo model assisted us in the interpretation of pulsing experiments, whereas MD calculations provided insights into the mechanism of dendrites thermal relaxation. We also developed a computational framework for measuring the dead lithium crystals from the experimental images.

  5. The TFTR lithium blanket module program

    SciTech Connect

    Jassby, D.L.; Bertone, P.C.; Creedon, R.L.; File, J.; Graumann, D.W.

    1985-02-01

    The Lithium Blanket Module (LBM) is an approximately 80X80X80 cm cubic module, representative of a helium-cooled lithium oxide fusion reactor blanket module, that will be installed on the TFTR (Tokamak Fusion Test Reactor) in late 1986. The principal objective of the LBM Program is to perform a series of neutron transport and tritium-breeding measurements throughout the LBM when it is exposed to the TFTR toroidal fusion neutron source, and to compare these data with the predictions of Monte Carlo (MCNP) neutronics codes. The LBM consists of 920 2.5-cm diameter breeder rods constructed of lithium oxide (Li/sub 2/O) pellets housed in thin-walled stainless steel tubes. Procedures for mass-producing 25,000 Li/sub 2/O pellets with satisfactory reproducibility were developed using purified Li/sub 2/O powder, and fabrication of all the breeder rods was completed in early 1985. Tritium assay methods were investigated experimentally using both small lithium metal samples and LBM-type pellets. This work demonstrated that the thermal extraction method will be satisfactory for accurate evaluation of the minute concentrations of tritium expected in the LBM pellets (0.1-1nCi/g).

  6. Lithium-air batteries: Something from nothing

    NASA Astrophysics Data System (ADS)

    Cheng, Fangyi; Chen, Jun

    2012-12-01

    The reversible reduction and evolution of oxygen are the key processes to be mastered before high-energy rechargeable lithium-air batteries can be successfully created. Now an advance towards this goal has been achieved with the synthesis of a pyrochlore catalyst that benefits from a mesoporous structure and oxygen deficiencies.

  7. STS lithium/CF(x) battery

    NASA Technical Reports Server (NTRS)

    Gnacek, Dee

    1991-01-01

    Lithium carbon fluoride batteries are used on Space Shuttle Rocket Boosters and external tanks. These batteries have been extremely successful in terms of mission reliability with the exception of cell yield variances. The function/system and battery descriptions are given. A description is given of the battery range safety system.

  8. Hazardous behavior of lithium batteries. Case histories

    NASA Technical Reports Server (NTRS)

    Marincic, N.

    1983-01-01

    Case histories were described of hazardous behavior for three different cell sizes ranging in nominal capacity from 300 mAh to 12,000 Ah. Design characteristics and other facts believed to have been responsible for the cell explosions, are presented. Obvious facts are discussed as causes for hazardous behavior of lithium batteries in general and oxyhalide batteries in particular.

  9. Interconnected hollow carbon nanospheres for stable lithium metal anodes.

    PubMed

    Zheng, Guangyuan; Lee, Seok Woo; Liang, Zheng; Lee, Hyun-Wook; Yan, Kai; Yao, Hongbin; Wang, Haotian; Li, Weiyang; Chu, Steven; Cui, Yi

    2014-08-01

    For future applications in portable electronics, electric vehicles and grid storage, batteries with higher energy storage density than existing lithium ion batteries need to be developed. Recent efforts in this direction have focused on high-capacity electrode materials such as lithium metal, silicon and tin as anodes, and sulphur and oxygen as cathodes. Lithium metal would be the optimal choice as an anode material, because it has the highest specific capacity (3,860 mAh g(-1)) and the lowest anode potential of all. However, the lithium anode forms dendritic and mossy metal deposits, leading to serious safety concerns and low Coulombic efficiency during charge/discharge cycles. Although advanced characterization techniques have helped shed light on the lithium growth process, effective strategies to improve lithium metal anode cycling remain elusive. Here, we show that coating the lithium metal anode with a monolayer of interconnected amorphous hollow carbon nanospheres helps isolate the lithium metal depositions and facilitates the formation of a stable solid electrolyte interphase. We show that lithium dendrites do not form up to a practical current density of 1 mA cm(-2). The Coulombic efficiency improves to ∼ 99% for more than 150 cycles. This is significantly better than the bare unmodified samples, which usually show rapid Coulombic efficiency decay in fewer than 100 cycles. Our results indicate that nanoscale interfacial engineering could be a promising strategy to tackle the intrinsic problems of lithium metal anodes. PMID:25064396

  10. Lithium-Induced Minimal Change Disease and Acute Kidney Injury

    PubMed Central

    Tandon, Parul; Wong, Natalie; Zaltzman, Jeffrey S

    2015-01-01

    Context: Lithium carbonate is a psychiatric medication commonly used in the treatment of bipolar disorder. It has been implicated in inducing nephrogenic diabetes inspidus, chronic tubulointerstitial nephropathy, and acute tubular necrosis. We describe a case of lithium-induced minimal change disease (MCD) and acute kidney injury (AKI). Case Report: A 32-year-old female with a medical history of bipolar disorder treated with chronic lithium therapy presented with anasarca, fatigue, and tremors. Work-up revealed supra-therapeutic lithium levels, hypoalbuminemia, and significant proteinuria. The patient was treated conservatively with fluids and discontinuation of lithium therapy. Subsequently, she developed significant AKI and persistent proteinuria. She underwent a renal biopsy that demonstrated effacement of podocyte foot processes consistent with lithium-induced MCD. This was treated with corticosteroids, which decreased the proteinuria and resolved all the patient's symptoms. Conclusion: Lithium-induced MCD is a rare disease that affects patients of all ages. It is often associated with therapeutic lithium and is typically resolved with discontinuation of lithium. In some cases, concurrent AKI may result due to vascular obstruction from hyperalbuminuria and associated renal interstitial edema. Corticosteroids may be needed to reduce the proteinuria and prevent progression to chronic kidney disease. As such, patients on lithium therapy may benefit from monitoring of glomerular function via urinalysis to prevent the onset of nephrotic syndrome. PMID:26258081

  11. Implications of NSTX Lithium Results for Magnetic Fusion Research

    SciTech Connect

    M. Ono, M.G. Bell, R.E. Bell, R. Kaita, H.W. Kugel, B.P. LeBlanc, J.M. Canik, S. Diem, S.P.. Gerhardt, J. Hosea, S. Kaye, D. Mansfield, R. Maingi, J. Menard, S. F. Paul, R. Raman, S.A. Sabbagh, C.H. Skinner, V. Soukhanovskii, G. Taylor, and the NSTX Research Team

    2010-01-14

    Lithium wall coating techniques have been experimentally explored on NSTX for the last five years. The lithium experimentation on NSTX started with a few milligrams of lithium injected into the plasma as pellets and it has evolved to a lithium evaporation system which can evaporate up to ~ 100 g of lithium onto the lower divertor plates between lithium reloadings. The unique feature of the lithium research program on NSTX is that it can investigate the effects of lithium in H-mode divertor plasmas. This lithium evaporation system thus far has produced many intriguing and potentially important results; the latest of these are summarized in a companion paper by H. Kugel. In this paper, we suggest possible implications and applications of the NSTX lithium results on the magnetic fusion research which include electron and global energy confinement improvements, MHD stability enhancement at high beta, ELM control, H-mode power threshold reduction, improvements in radio frequency heating and non-inductive plasma start-up performance, innovative divertor solutions and improved operational efficiency.

  12. Interconnected hollow carbon nanospheres for stable lithium metal anodes

    NASA Astrophysics Data System (ADS)

    Zheng, Guangyuan; Lee, Seok Woo; Liang, Zheng; Lee, Hyun-Wook; Yan, Kai; Yao, Hongbin; Wang, Haotian; Li, Weiyang; Chu, Steven; Cui, Yi

    2014-08-01

    For future applications in portable electronics, electric vehicles and grid storage, batteries with higher energy storage density than existing lithium ion batteries need to be developed. Recent efforts in this direction have focused on high-capacity electrode materials such as lithium metal, silicon and tin as anodes, and sulphur and oxygen as cathodes. Lithium metal would be the optimal choice as an anode material, because it has the highest specific capacity (3,860 mAh g-1) and the lowest anode potential of all. However, the lithium anode forms dendritic and mossy metal deposits, leading to serious safety concerns and low Coulombic efficiency during charge/discharge cycles. Although advanced characterization techniques have helped shed light on the lithium growth process, effective strategies to improve lithium metal anode cycling remain elusive. Here, we show that coating the lithium metal anode with a monolayer of interconnected amorphous hollow carbon nanospheres helps isolate the lithium metal depositions and facilitates the formation of a stable solid electrolyte interphase. We show that lithium dendrites do not form up to a practical current density of 1 mA cm-2. The Coulombic efficiency improves to ˜99% for more than 150 cycles. This is significantly better than the bare unmodified samples, which usually show rapid Coulombic efficiency decay in fewer than 100 cycles. Our results indicate that nanoscale interfacial engineering could be a promising strategy to tackle the intrinsic problems of lithium metal anodes.

  13. A chemically stable PVD multilayer encapsulation for lithium microbatteries

    NASA Astrophysics Data System (ADS)

    Ribeiro, J. F.; Sousa, R.; Cunha, D. J.; Vieira, E. M. F.; Silva, M. M.; Dupont, L.; Goncalves, L. M.

    2015-10-01

    A multilayer physical vapour deposition (PVD) thin-film encapsulation method for lithium microbatteries is presented. Lithium microbatteries with a lithium cobalt oxide (LiCoO2) cathode, a lithium phosphorous oxynitride (LiPON) electrolyte and a metallic lithium anode are under development, using PVD deposition techniques. Metallic lithium film is still the most common anode on this battery technology; however, it presents a huge challenge in terms of material encapsulation (lithium reacts with almost any materials deposited on top and almost instantly begins oxidizing in contact with atmosphere). To prove the encapsulation concept and perform all the experiments, lithium films were deposited by thermal evaporation technique on top of a glass substrate, with previously patterned Al/Ti contacts. Three distinct materials, in a multilayer combination, were tested to prevent lithium from reacting with protection materials and atmosphere. These multilayer films were deposited by RF sputtering and were composed of lithium phosphorous oxide (LiPO), LiPON and silicon nitride (Si3N4). To complete the long-term encapsulation after breaking the vacuum, an epoxy was applied on top of the PVD multilayer. In order to evaluate oxidation state of lithium films, the lithium resistance was measured in a four probe setup (cancelling wires/contact resistances) and resistivity calculated, considering physical dimensions. A lithium resistivity of 0.16 Ω μm was maintained for more than a week. This PVD multilayer exonerates the use of chemical vapour deposition (CVD), glove-box chambers and sample manipulation between them, significantly reducing the fabrication cost, since battery and its encapsulation are fabricated in the same PVD chamber.

  14. Thermodynamic studies on lithium ferrites

    SciTech Connect

    Rakshit, S.K.; Parida, S.C.; Naik, Y.P.; Chaudhary, Ziley Singh; Venugopal, V.

    2011-05-15

    Thermodynamic studies on ternary oxides of Li-Fe-O systems were carried out using differential scanning calorimetry, Knudsen effusion mass spectrometry, and solid-state electrochemical technique based on fluoride electrolyte. Heat capacities of LiFe{sub 5}O{sub 8}(s) and LiFeO{sub 2}(s) were determined in the temperature range 127-861 K using differential scanning calorimetry. Gibbs energies of formation of LiFe{sub 5}O{sub 8}(s) and LiFeO{sub 2}(s) were determined using Knudsen effusion mass spectrometry and solid-state galvanic cell technique. The combined least squares fits can be represented as {Delta}{sub f}G{sub m}{sup o}(LiFe{sub 5}O{sub 8},s,T)/kJ mol{sup -1} ({+-}6)=-2341+0.6764(T/K) (588{<=}T/K{<=}971) {Delta}{sub f}G{sub m}{sup o}(LiFeO{sub 2},s,T)/kJ mol{sup -1} ({+-}3)=-708+0.1656(T/K) (569{<=}T/K{<=}1021) The temperature independent term of the above equations represents {Delta}{sub f}H{sup o}{sub m}(T{sub av}) and temperature dependent term represents negative change in entropy of the respective compounds. Thermodynamic analysis shows that LiFe{sub 5}O{sub 8}(s) is more stable compared to LiFeO{sub 2}(s). -- Graphical abstract: Comparison of {Delta}{sub f}G{sub m}{sup o}(T) of lithium ferrites determined using different techniques. Display Omitted Highlights: {yields} Thermodynamic studies on Li-Fe-O system using DSC, KEQMS and galvanic cell. {yields} Heat capacities of LiFe{sub 5}O{sub 8}(s) and LiFeO{sub 2}(s) were determined using DSC 127-861 K. {yields} {Delta}{sub f}G{sup o}{sub m} of these compounds were determined and compared. {yields} Thermodynamic tables for LiFe{sub 5}O{sub 8}(s) and LiFeO{sub 2}(s) were constructed.

  15. Solid state thin film battery having a high temperature lithium alloy anode

    DOEpatents

    Hobson, David O.

    1998-01-01

    An improved rechargeable thin-film lithium battery involves the provision of a higher melting temperature lithium anode. Lithium is alloyed with a suitable solute element to elevate the melting point of the anode to withstand moderately elevated temperatures.

  16. Lithium compound deposition on mesocarbon microbead anode of lithium ion batteries after long-term cycling.

    PubMed

    Yang, Lijie; Cheng, Xinqun; Gao, Yunzhi; Zuo, Pengjian; Ma, Yulin; Du, Chunyu; Shen, Bin; Cui, Yingzhi; Guan, Ting; Yin, Geping

    2014-08-13

    Lithium compound deposition on mesocarbon microbead (MCMB) anode after long-term cycling was studied in LiCoO2/MCMB battery. Lithium compound deposition did not generate on the activated MCMB anode, but it generated unevenly on the long-term cycled anode. Gray deposition composed of dendrites and particles was formed on the lower surface of the MCMB layer first, then on the upper surface. The deposition and MCMB layer peeled off from the current collector, and a bump was formed in the cycled anode. The exfoliation and thick deposition increased the ohmic resistance, film resistance, and charge transfer resistance of the cell and decreased the capacity significantly. Metallic lithium did not exist in either the upper or the lower deposition layer according to the results of X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), the discharge curve, and anode potential. The outer region of both the lower and the upper deposition layers consisted of Li2CO3, LiOH, ROCO2Li, and ROLi. The inner region of the etched lower deposition layer mainly consisted of Li2O, LiF, and Li2CO3, and that of the etched upper deposition layer mainly consisted of Li2CO3, ROCO2Li, ROLi, and LiF. Solid electrolyte interphase (SEI) film hindering the intercalation of lithium ions into carbon layers and LiCoO2 cathode providing lithium source for the deposition were the two reasons leading to the formation of lithium compound deposition during long-term cycles. Because SEI film on the lower surface of MCMB layer was thicker than that on the upper surface, lithium compound deposition generated on the lower surface first. PMID:25020035

  17. Lithium storage mechanism in cubic lithium copper titanate anode material upon lithiation/delithiation process

    NASA Astrophysics Data System (ADS)

    Chen, Wei; Zhou, Zhengrong; Liang, Hanfeng; Shao, Lianyi; Shu, Jie; Wang, Zhoucheng

    2015-05-01

    Complex spinel Li2CuTi3O8 with a space group of Fd-3m is prepared for the first time by a simple solid state reaction route. This compound has different space group from the previous reported Li2MTi3O8 (M = Zn, Co, Mg, Ni and Mn) with a space group of P4332. It shows reversibility for lithium storage in the cubic structure. A reversible capacity of 203 mAh g-1 can be delivered at a current density of 100 mA g-1 after 50 cycles with the capacity retention of 70.7%. The electrochemical reaction mechanism between Li2CuTi3O8 and lithium is investigated by various in-situ and ex-situ observations. Rietveld refinement results show that Li2CuTi3O8 has multiple interstitials to accommodate lithium ions during the lithiation process, in which the irregular octahedral 32e sites would be occupied by lithium ions at high working potentials and the regular octahedral 16c sites would be occupied by lithium ions at low working potentials. Besides, a reversible migration of copper ions can found during discharge process. Based on the reverse delithiation process, it is known that the whole charge-discharge process is quasi-reversible for Li2CuTi3O8. Therefore, Li2CuTi3O8 shows high structural stability as a promising lithium storage material for lithium-ion batteries.

  18. Transparent plastic scintillators for neutron detection based on lithium salicylate

    NASA Astrophysics Data System (ADS)

    Mabe, Andrew N.; Glenn, Andrew M.; Carman, M. Leslie; Zaitseva, Natalia P.; Payne, Stephen A.

    2016-01-01

    Transparent plastic scintillators with pulse shape discrimination containing 6Li salicylate have been synthesized by bulk polymerization with a maximum 6Li loading of 0.40 wt%. Photoluminescence and scintillation responses to gamma-rays and neutrons are reported herein. Plastics containing 6Li salicylate exhibit higher light yields and permit a higher loading of 6Li as compared to previously reported plastics based on lithium 3-phenylsalicylate. However, pulse shape discrimination performance is reduced in lithium salicylate plastics due to the requirement of adding more nonaromatic monomers to the polymer matrix as compared to those based on lithium 3-phenylsalicylate. Reduction in light yield and pulse shape discrimination performance in lithium-loaded plastics as compared to pulse shape discrimination plastics without lithium is interpreted in terms of energy transfer interference by the aromatic lithium salts.

  19. Electrochemistry of dioxygen in lithium-air batteries

    NASA Astrophysics Data System (ADS)

    Hardwick, Laurence

    2014-03-01

    The non-aqueous lithium-oxygen battery is one of a host of emerging opportunities available for enhanced energy storage. Unlike a conventional battery where the reagents are contained within the cell, the lithium-oxygen cell uses dioxygen from the atmosphere to electrochemically form the discharge product lithium peroxide. Degrees of reversible oxidation and formation of lithium peroxide has been demonstrated in a number of non-aqueous electrolyte classes, mostly notably in dimethysulfoxide based electrolytes, thus making the lithium-oxygen cell a potential energy storage device. This talk will present our groups recent results of the electrochemistry of dioxygen in non-aqueous electrolytes, of which particular electrolytes could have practical application within a lithium-oxygen cell. Discussion will touch upon how the electrochemistry can be related to electrode substrate and will be presented with in situ spectroscopic studies that identify intermediate and surface species during the oxygen reduction reaction. Support from the EPSRC is gratefully acknowledged

  20. Read-write holographic memory with iron-doped lithium niobate

    NASA Technical Reports Server (NTRS)

    Alphonse, G. A.; Phillips, W.

    1975-01-01

    The response of iron doped lithium niobate under conditions corresponding to hologram storage and retrieval is described, and the material's characteristics are discussed. The optical sensitivity can be improved by heavy chemical reduction of lightly doped crystals such that most of the iron is in the divalent state, the remaining part being trivalent. The best reduction process found to be reproducible so far is the anneal of the doped crystal in the presence of a salt such as lithium carbonate. It is shown by analysis and simulation that a page-oriented read-write holographic memory with 1,000 bits per page would have a cycle time of about 60 ms and a signal-to-noise ratio of 27 db. This cycle time, although still too long for a practical system, represents an improvement of two orders of magnitude over that of previous laboratory prototypes using different storage media.