Science.gov

Sample records for manufacturing program summary

  1. National Center for Advanced Information Components Manufacturing. Program summary report, Volume 1

    SciTech Connect

    1996-10-01

    The National Center for Advanced Information Components Manufacturing focused on manufacturing research and development for flat panel displays, advanced lithography, microelectronics, and optoelectronics. This report provides an overview of the program, summaries of the technical projects, and key program accomplishments.

  2. National Center for Advanced Information Components Manufacturing. Program summary report, Volume II

    SciTech Connect

    1996-10-01

    The National Center for Advanced Information Components Manufacturing focused on manufacturing research and development for flat panel displays, advanced lithography, microelectronics, and optoelectronics. This report provides an overview of the program, program history, summaries of the technical projects, and key program accomplishments.

  3. Manufacturing Educational Change: Impact Evaluation of the Lansing Area Manufacturing Partnership Pilot Program. Executive Summary.

    ERIC Educational Resources Information Center

    MacAllum, Keith; Taylor, Susan Hubbard; Johnson, Amy Bell

    The Lansing Area Manufacturing Partnership (LAMP) is an academically rigorous, business/labor-driven school-to-career program in Lansing, Michigan, that includes business, union, school, and parent partners and provides participating students with work-based learning experiences for 2.5 hours every day throughout their senior year. LAMP's…

  4. Solid State Lighting LED Manufacturing Roundtable Summary

    SciTech Connect

    none,

    2010-03-31

    Summary of a meeting of LED experts to develop proposed priority tasks for the Manufacturing R&D initiative, including task descriptions, discussion points, recommendations, and presentation highlights.

  5. Solid State Lighting OLED Manufacturing Roundtable Summary

    SciTech Connect

    none,

    2010-03-31

    Summary of a meeting of OLED experts to develop proposed priority tasks for the Manufacturing R&D initiative, including task descriptions, discussion points, recommendations, and presentation highlights.

  6. Biofuels program summary. Volume 2: Research summaries

    NASA Astrophysics Data System (ADS)

    1990-01-01

    The Federal government has supported research on biomass technology and energy from municipal waste since 1975. Separate research programs were conducted until 1985 when the two were merged into biofuels and municipal waste technology to take advantage of their many similarities in conversion requirements and research needs. The purpose of the biofuels program is to provide focus, direction, coordination, and funding for the development of technologies that produce tailored energy crops and convert these crops and wastes to fuels. The FY 1989 program includes research on the production (growth) of biomass and its conversion to fuels. Research on biomass production involves the development and use of genetically improved trees and grasses specifically for their energy conversion characteristics (terrestrial energy crops). The Biofuels Program Summary is prepared each year and consists of a two-volume reference set describing the technological advances, current projects, and future research and development (R and D) directions of the program. This volume (Volume 2-Research Summaries) is a compilation of detailed descriptions of the R and D projects performed by the national laboratories and their subcontractors from industry, universities, and nonprofit research institutions.

  7. Delinquency Prevention Works. Program Summary.

    ERIC Educational Resources Information Center

    Bilchik, Shay

    The Office of Juvenile Justice and Delinquency Prevention (OJJDP) compiled this summary in order to assist states and jurisdictions in their delinquency prevention efforts. The summary provides a synthesis of current information on a broad range of programs and strategies which seek to prevent delinquency. The theory of risk-focused prevention is…

  8. Biomass energy systems program summary

    SciTech Connect

    1980-07-01

    Research programs in biomass which were funded by the US DOE during fiscal year 1978 are listed in this program summary. The conversion technologies and their applications have been grouped into program elements according to the time frame in which they are expected to enter the commercial market. (DMC)

  9. Wind energy systems: program summary

    SciTech Connect

    1980-05-01

    The Federal Wind Energy Program (FWEP) was initiated to provide focus, direction and funds for the development of wind power. Each year a summary is prepared to provide the American public with an overview of government sponsored activities in the FWEP. This program summary describes each of the Department of Energy's (DOE) current wind energy projects initiated or renewed during FY 1979 (October 1, 1978 through September 30, 1979) and reflects their status as of April 30, 1980. The summary highlights on-going research, development and demonstration efforts and serves as a record of progress towards the program objectives. It also provides: the program's general management structure; review of last year's achievements; forecast of expected future trends; documentation of the projects conducted during FY 1979; and list of key wind energy publications.

  10. Ocean energy program summary

    SciTech Connect

    Not Available

    1990-01-01

    The oceans are the world's largest solar energy collector and storage system. Covering 71% of the earth's surface, they collect and store this energy as waves, currents, and thermal and salinity gradients. The purpose of the US Department of Energy's (DOE) Ocean Energy Technology (OET) Program is to develop techniques that harness this ocean energy cost-effectively and in a way that does not harm the environment. The program seeks to develop ocean energy technology to a point where industry can accurately assess whether the technology is a viable energy conversion alternative, or supplement, to current power-generating systems. In past studies, DOE identified ocean thermal energy conversion (OTEC), which uses the temperature difference between warm surface water and cold deep water, as the most promising of the ocean energy technologies. As a result, the OET Program is concentrating on research that advances the OTEC technology. The program also continues to monitor and study developments in wave energy, ocean current, and salinity gradient concepts; but it is not actively developing these technologies now. 13 figs.

  11. Ocean energy program summary

    NASA Astrophysics Data System (ADS)

    1990-01-01

    The oceans are the world's largest solar energy collector and storage system. Covering 71 percent of the earth's surface, they collect and store this energy as waves, currents, and thermal and salinity gradients. The purpose of the U.S. Department of Energy's (DOE) Ocean Energy Technology (OET) Program is to develop techniques that harness this ocean energy cost effectively and in a way that does not harm the environment. The program seeks to develop ocean energy technology to a point where industry can accurately assess whether the technology is a viable energy conversion alternative, or supplement, to current power generating systems. In past studies, DOE identified ocean thermal energy conversion (OTEC), which uses the temperature difference between warm surface water and cold deep water, as the most promising of the ocean energy technologies. As a result, the OET Program is concentrating on research that advances the OTEC technology. The program also continues to monitor and study developments in wave energy, ocean current, and salinity gradient concepts; but it is not actively developing these technologies now.

  12. Subsystems component definitions summary program

    NASA Technical Reports Server (NTRS)

    Scott, A. Don; Thomas, Carolyn C.; Simonsen, Lisa C.; Hall, John B., Jr.

    1991-01-01

    A computer program, the Subsystems Component Definitions Summary (SUBCOMDEF), was developed to provide a quick and efficient means of summarizing large quantities of subsystems component data in terms of weight, volume, resupply, and power. The program was validated using Space Station Freedom Program Definition Requirements Document data for the internal and external thermal control subsystem. Once all component descriptions, unit weights and volumes, resupply, and power data are input, the user may obtain a summary report of user-specified portions of the subsystem or of the entire subsystem as a whole. Any combination or all of the parameters of wet and dry weight, wet and dry volume, resupply weight and volume, and power may be displayed. The user may vary the resupply period according to individual mission requirements, as well as the number of hours per day power consuming components operate. Uses of this program are not limited only to subsystem component summaries. Any applications that require quick, efficient, and accurate weight, volume, resupply, or power summaries would be well suited to take advantage of SUBCOMDEF's capabilities.

  13. Geothermal energy program summary

    SciTech Connect

    Not Available

    1990-01-01

    The Geothermal Technology Division (GTD) of the US Department of Energy (DOE) is charged with the lead federal role in the research and development (R D) of technologies that will assist industry in economically exploiting the nation's vast geothermal resources. The GTD R D Program represents a comprehensive, balanced approach to establishing all forms of geothermal energy as significant contributors to the nation's energy supply. It is structured both to maintain momentum in the growth of the existing hydrothermal industry and to develop long-term options offering the greatest promise for practical applications. This volume, Volume 2, contains a detailed compilation of each GTD-funded R D activity performed by national laboratories or under contract to industrial, academic, and nonprofit research institutions.

  14. Solar thermal technologies program summary

    SciTech Connect

    Not Available

    1985-05-01

    The primary applications being developed in solar thermal technology are the production of electricity and industrial process heat. Additional applications, such as the production of a transportable fuel, are also being studied to determine their feasibility. Two collector concepts are being examined: central receiver and distributed receiver. Some significant achievements are briefly described, as well as program goals and strategies. The research plan for the 1984 fiscal year is also briefly discussed, including a summary of the budget. (LEW)

  15. Manufacturing Math Classes: An Instructional Program Guide for Manufacturing Workers.

    ERIC Educational Resources Information Center

    McBride, Pamela G.; And Others

    This program guide documents a manufacturing job family curriculum that develops competence in generic work force education skills through three courses: Reading Rulers, Charts, and Gauges and Math for Manufacturing Workers I and II. An annotated table of contents lists a brief description of the questions answered in each section. An introduction…

  16. Building Technologies Program Planning Summary

    SciTech Connect

    none,

    2009-11-01

    The U.S. Department of Energy’s (DOE) Building Technologies Program (BTP) works in partnership with industry, state, municipal, and other federal organizations to achieve the goals of marketable net-zero energy buildings. To carry out its mission, BTP involves builders; appliance, window, lighting, operational systems, and component manufacturers; and end users in setting the program’s research priorities. These groups advise and help guide BTP through implementing, deploying, and standardizing new technologies, equipment, and processes being developed and tested in DOE’s national laboratories and in real-world applications in many U.S. communities.

  17. Summary of NDE of Additive Manufacturing Efforts in NASA

    NASA Technical Reports Server (NTRS)

    Waller, Jess; Saulsberry, Regor; Parker, Bradford; Hodges, Kenneth; Burke, Eric; Taminger, Karen

    2014-01-01

    (1) General Rationale for Additive Manufacturing (AM): (a) Operate under a 'design-to-constraint' paradigm, make parts too complicated to fabricate otherwise, (b) Reduce weight by 20 percent with monolithic parts, (c) Reduce waste (green manufacturing), (e) Eliminate reliance on Original Equipment Manufacturers for critical spares, and (f) Extend life of in-service parts by innovative repair methods; (2) NASA OSMA NDE of AM State-of-the-Discipline Report; (3) Overview of NASA AM Efforts at Various Centers: (a) Analytical Tools, (b) Ground-Based Fabrication (c) Space-Based Fabrication; and (d) Center Activity Summaries; (4) Overview of NASA NDE data to date on AM parts; and (5) Gap Analysis/Recommendations for NDE of AM.

  18. Fossil energy program. Summary document

    SciTech Connect

    1980-05-01

    This program summary document presents a comprehensive overview of the research, development, and demonstration (RD and D) activities that will be performed in FY 1981 by the Assistant Secretary for Fossil Energy (ASFE), US Department of Energy (DOE). The ASFE technology programs for the fossil resources of coal, petroleum (including oil shale) and gas have been established with the goal of making substantive contributions to the nation's future supply and efficienty use of energy. On April 29, 1977, the Administration submitted to Congress the National Energy Plan (NEP) and accompanying legislative proposals designed to establish a coherent energy policy structure for the United States. Congress passed the National Energy Act (NEA) on October 15, 1978, which allows implementation of the vital parts of the NEP. The NEP was supplemented by additional energy policy statements culminating in the President's address on July 15, 1979, presenting a program to further reduce dependence on imported petroleum. The passage of the NEA-related energy programs represent specific steps by the Administration and Congress to reorganize, redirect, and clarify the role of the Federal Government in the formulation and execution of national energy policy and programs. The energy technology RD and D prog4rams carried out by ASFE are an important part of the Federal Government's effort to provide the combination and amounts of energy resources needed to ensure national security and continued economic growth.

  19. Pollution Prevention Program: Technology summary

    SciTech Connect

    Not Available

    1994-02-01

    The Department of Energy (DOE) has established a national Research, Development, Demonstration, Testing, and Evaluation (RDDT&E) Program for pollution prevention and waste minimization at its production plants During FY89/90 the Office of Environmental Restoration and Waste Management (EM), through the Office of Technology Development (OTD), established comprehensive, pollution prevention technical support programs to demonstrate new, environmentally-conscious technology for production processes. The RDDT&E program now entails collaborative efforts across DOE. The Pollution Prevention Program is currently supporting three major activities: The DOE/US Air Force Memorandum of Understanding Program is a collaborative effort to utilize the combined resources of DOE and the Department of Defense, eliminate duplication of effort in developing technologies, and to facilitate technology solutions aimed at reducing waste through process modification, material substitution or recycling. The Waste Component Recycle, Treatment and Disposal Integrated Demonstration (WeDID) will develop recycle, treatment, and disposal processes and associated technologies for use in the dismantlement of non-nuclear weapons components, to support US arms treaties and policies. This program will focus on meeting all security and regulatory requirements (with additional benefit to the commercial electronics industry). The Environmentally Conscious Manufacturing Integrated Demonstration (ECMID) will effectively implement ECM technologies that address both the needs of the DOE Complex and US electronics industry, and encourage strong interaction between DOE and US industry. The ECMID will also develop life cycle analysis tools that will aid decisionmakers in selecting the optimum process based on the tradeoffs between cost an environmental impact.

  20. Integrated flexible manufacturing program for manufacturing automation and rapid prototyping

    NASA Technical Reports Server (NTRS)

    Brooks, S. L.; Brown, C. W.; King, M. S.; Simons, W. R.; Zimmerman, J. J.

    1993-01-01

    The Kansas City Division of Allied Signal Inc., as part of the Integrated Flexible Manufacturing Program (IFMP), is developing an integrated manufacturing environment. Several systems are being developed to produce standards and automation tools for specific activities within the manufacturing environment. The Advanced Manufacturing Development System (AMDS) is concentrating on information standards (STEP) and product data transfer; the Expert Cut Planner system (XCUT) is concentrating on machining operation process planning standards and automation capabilities; the Advanced Numerical Control system (ANC) is concentrating on NC data preparation standards and NC data generation tools; the Inspection Planning and Programming Expert system (IPPEX) is concentrating on inspection process planning, coordinate measuring machine (CMM) inspection standards and CMM part program generation tools; and the Intelligent Scheduling and Planning System (ISAPS) is concentrating on planning and scheduling tools for a flexible manufacturing system environment. All of these projects are working together to address information exchange, standardization, and information sharing to support rapid prototyping in a Flexible Manufacturing System (FMS) environment.

  1. Summary of development and recommendations for a quality assurance program for the procurement and manufacture of urban mass transit operating equipment and systems

    NASA Technical Reports Server (NTRS)

    Witkin, S. A.

    1976-01-01

    A viable quality program for the urban mass transit industry, and a management approach to ensure compliance with the program are outlined. Included are: (1) a set of guidelines for quality assurance to be imposed on transit authorities, and a management approach to ensure compliance with them; (2) a management approach to be used by the transit authorities (properties) for assuring compliance with the QA guidelines; and (3) quality assurance guidelines to be imposed by properties and umta for procurement of hardware and systems.

  2. Computer Integrated Manufacturing Programs in Higher Education.

    ERIC Educational Resources Information Center

    International Business Machines Corp., Milford, CT. Academic Information Systems.

    This publication focuses on computer integrated manufacturing (CIM) programs at several higher education institutions which teach the use of computing in manufacturing. The document describes programs at the following institutions: University of Alabama (where researchers are investigating CIM techniques with a key focus on transferring their…

  3. Advanced Initiation Systems Manufacturing Level 2 Milestone Completion Summary

    SciTech Connect

    Chow, R; Schmidt, M

    2009-10-01

    Milestone Description - Advanced Initiation Systems Detonator Design and Prototype. Milestone Grading Criteria - Design new generation chip slapper detonator and manufacture a prototype using advanced manufacturing processes, such as all-dry chip metallization and solvent-less flyer coatings. The advanced processes have been developed for manufacturing detonators with high material compatibility and reliability to support future LEPs, e.g. the B61, and new weapons systems. Perform velocimetry measurements to determine slapper velocity as a function of flight distance. A prototype detonator assembly and stripline was designed for low-energy chip slappers. Pictures of the prototype detonator and stripline are shown. All-dry manufacturing processes were used to address compatibility issues. KCP metallized the chips in a physical vapor deposition system through precision-aligned shadow masks. LLNL deposited a solvent-less polyimide flyer with a processes called SLIP, which stands for solvent-less vapor deposition followed by in-situ polymerization. LANL manufactured the high-surface-area (HSA) high explosive (HE) pellets. Test fires of two chip slapper designs, radius and bowtie, were performed at LLNL in the High Explosives Application Facility (HEAF). Test fires with HE were conducted to establish the threshold firing voltages. pictures of the chip slappers before and after test fires are shown. Velocimetry tests were then performed to obtain slapper velocities at or above the threshold firing voltages. Figure 5 shows the slapper velocity as a function of distance and time at the threshold voltage, for both radius and bowtie bridge designs. Both designs were successful at initiating the HE at low energy levels. Summary of Accomplishments are: (1) All-dry process for chip manufacture developed; (2) Solventless process for slapper materials developed; (3) High-surface area explosive pellets developed; (4) High performance chip slappers developed; (5) Low-energy chip

  4. Implementing Computer Integrated Manufacturing Technician Program.

    ERIC Educational Resources Information Center

    Gibbons, Roger

    A computer-integrated manufacturing (CIM) technician program was developed to provide training and technical assistance to meet the needs of business and industry in the face of the demands of high technology. The Computer and Automated Systems Association (CASA) of the Society of Manufacturing Engineers provided the incentive and guidelines…

  5. AMPS/PC - AUTOMATIC MANUFACTURING PROGRAMMING SYSTEM

    NASA Technical Reports Server (NTRS)

    Schroer, B. J.

    1994-01-01

    The AMPS/PC system is a simulation tool designed to aid the user in defining the specifications of a manufacturing environment and then automatically writing code for the target simulation language, GPSS/PC. The domain of problems that AMPS/PC can simulate are manufacturing assembly lines with subassembly lines and manufacturing cells. The user defines the problem domain by responding to the questions from the interface program. Based on the responses, the interface program creates an internal problem specification file. This file includes the manufacturing process network flow and the attributes for all stations, cells, and stock points. AMPS then uses the problem specification file as input for the automatic code generator program to produce a simulation program in the target language GPSS. The output of the generator program is the source code of the corresponding GPSS/PC simulation program. The system runs entirely on an IBM PC running PC DOS Version 2.0 or higher and is written in Turbo Pascal Version 4 requiring 640K memory and one 360K disk drive. To execute the GPSS program, the PC must have resident the GPSS/PC System Version 2.0 from Minuteman Software. The AMPS/PC program was developed in 1988.

  6. `Climate wise` program at the Cosmair, Inc. Clark Manufacturing Facility

    SciTech Connect

    Kraly, K.

    1997-12-31

    Viewgraphs from the conference presentation are reproduced in this paper, which outlines energy efficiency improvements and emissions reductions at a hair care products manufacturing facility. Program management focuses on employee involvement in internal audits, utility tracking, public relations, and preventative maintenance. Energy savings, cost savings, and emission reductions are presented for 1996 and projected to the year 2000. Other program aspects outlined include a summary of utility costs; solid waste; chilled water system modifications; lighting modifications; boiler upgrades; and heating, ventilating, and air conditioning improvements.

  7. Apollo Program Summary Report: Synopsis of the Apollo Program Activities and Technology for Lunar Exploration

    NASA Technical Reports Server (NTRS)

    1975-01-01

    Overall program activities and the technology developed to accomplish lunar exploration are discussed. A summary of the flights conducted over an 11-year period is presented along with specific aspects of the overall program, including lunar science, vehicle development and performance, lunar module development program, spacecraft development testing, flight crew summary, mission operations, biomedical data, spacecraft manufacturing and testing, launch site facilities, equipment, and prelaunch operations, and the lunar receiving laboratory. Appendixes provide data on each of the Apollo missions, mission type designations, spacecraft weights, records achieved by Apollo crewmen, vehicle histories, and a listing of anomalous hardware conditions noted during each flight beginning with Apollo 4.

  8. 42 CFR 10.2 - Summary of 340B Drug Pricing Program.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 42 Public Health 1 2013-10-01 2013-10-01 false Summary of 340B Drug Pricing Program. 10.2 Section... 340B DRUG PRICING PROGRAM General Provisions § 10.2 Summary of 340B Drug Pricing Program. Section 340B...(a)(1) and 340B(a)(2)(A).Manufacturers participating in the 340B Drug Pricing Program (340B...

  9. 42 CFR 10.2 - Summary of 340B Drug Pricing Program.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 42 Public Health 1 2014-10-01 2014-10-01 false Summary of 340B Drug Pricing Program. 10.2 Section... 340B DRUG PRICING PROGRAM General Provisions § 10.2 Summary of 340B Drug Pricing Program. Section 340B...(a)(1) and 340B(a)(2)(A). Manufacturers participating in the 340B Drug Pricing Program (340B...

  10. Integration Framework of Process Planning based on Resource Independent Operation Summary to Support Collaborative Manufacturing

    SciTech Connect

    Kulvatunyou, Boonserm; Wysk, Richard A.; Cho, Hyunbo; Jones, Albert

    2004-06-01

    In today's global manufacturing environment, manufacturing functions are distributed as never before. Design, engineering, fabrication, and assembly of new products are done routinely in many different enterprises scattered around the world. Successful business transactions require the sharing of design and engineering data on an unprecedented scale. This paper describes a framework that facilitates the collaboration of engineering tasks, particularly process planning and analysis, to support such globalized manufacturing activities. The information models of data and the software components that integrate those information models are described. The integration framework uses an Integrated Product and Process Data (IPPD) representation called a Resource Independent Operation Summary (RIOS) to facilitate the communication of business and manufacturing requirements. Hierarchical process modeling, process planning decomposition and an augmented AND/OR directed graph are used in this representation. The Resource Specific Process Planning (RSPP) module assigns required equipment and tools, selects process parameters, and determines manufacturing costs based on two-level hierarchical RIOS data. The shop floor knowledge (resource and process knowledge) and a hybrid approach (heuristic and linear programming) to linearize the AND/OR graph provide the basis for the planning. Finally, a prototype system is developed and demonstrated with an exemplary part. Java and XML (Extensible Markup Language) are used to ensure software and information portability.

  11. Summary of foreign HTGR programs

    SciTech Connect

    Not Available

    1980-06-01

    This report contains pertinent information on the status, objectives, budgets, major projects and facilities, as well as user, industrial and governmental organizations involved in major foreign gas-cooled thermal reactor programs. This is the second issue of this document (the first was issued in March 1979). The format has been revised to consolidate material according to country. These sections are followed by the foreign HTGR program index which serves as a quick reference to some of the many acronyms associated with the foreign HTGR programs.

  12. Short Rotation Woody Crops Program: Project summaries

    SciTech Connect

    Not Available

    1986-11-01

    This document is a compilation of summaries describing research efforts in the US Department of Energy's Short Rotation Woody Crops Program (SRWCP). The SRWCP is sponsored by DOE's Biofuels and Municipal Waste Technology Division and is field-managed at Oak Ridge National Laboratory. The SRWCP is an integrated basic research program with 18 field research projects throughout the United States. The overall objective of the program is to improve the productivity and increase the cost efficiency of growing and harvesting woody trees and shrubs. In a competitive technical review, 25 projects were chosen to form a new research program. Although some of the original projects have ended and new ones have begun, many of the long-term research projects still form the core of the SRWCP. This document contains individual summaries of each of the 18 research projects in the SRWCP from October 1985 to October 1986. Each summary provides the following information: name and address of the contracting institution, principal investigator, project title, current subcontract or grant number, period of performance, and annual funding through fiscal year 1986. In addition, each summary contains a brief description of the project rationale, objective, approach, status, and future efforts. A list of publications that have resulted from DOE-sponsored research follows many of the summaries.

  13. MOTT PROGRAM SUMMARIES (TITLE SUPPLIED).

    ERIC Educational Resources Information Center

    Flint Board of Education, MI.

    THE BETTER TOMORROW FOR THE URBAN CHILD PROGRAM (BTU) ATTEMPTS TO HELP INNER-CITY CHILDREN BECOME MORE EFFECTIVE CITIZENS, BOTH EDUCATIONALLY AND SOCIALLY, THROUGH THE USE OF ADDITIONAL HUMAN AND MATERIAL RESOURCES. THE GOALS ARE TO RAISE THE LEVEL OF SCHOOL READINESS, TO DEVELOP A GREATER MOTIVATION FOR LEARNING, AND TO IMPROVE STUDENT SELF-IMAGE…

  14. Wind energy technology program summary

    NASA Astrophysics Data System (ADS)

    1984-10-01

    The purpose of the Federal Wind Energy Technology Program is to perform research that will enable the private sector to develop and utilize safe, reliable, and efficient wind energy systems. Generic research will provide the technology base and scientific understanding necessary to allow industry to develop wind energy systems competitive with conventional energy sources. The goal of the DOE wind program is to improve the basic understanding of aerodynamics and structural dynamics in order to more accurately predict wind turbine aerodynamic performance, natural resonance frequencies, and structural loads. Areas included in the research plan being developed for the next five years include: advanced fluid dynamics, aerodynamics research, structural dynamics research, and advanced components and systems research, including multimegawatt (MOD-5) development.

  15. Advanced Rotorcraft Transmission program summary

    NASA Astrophysics Data System (ADS)

    Bossler, Robert B., Jr.; Heath, Gregory F.

    1992-07-01

    The current status of the Advanced Rotorcraft Transmission (ART) program is reviewed. The discussion includes a general configuration and face gear description, weight analysis, stress analysis, reliability analysis, acoustic analysis, face gear testing, and planned torque split testing. Design descriptions include the face gear webs sized for equal stiffness, a positive engagement clutch, the lubrication system, and a high contact ratio planetary. Test results for five gear materials and three housing materials are presented.

  16. Alouette-ISIS program summary

    NASA Technical Reports Server (NTRS)

    Jackson, John E.

    1986-01-01

    The Alouette-ISIS program was a joint undertaking between Canada and the United States. Canada provided the Alouette and ISIS spacecraft, data acquisition, and satellite control. The USA provided launch capability, satellite tracking, and data acquisition. Brief descriptions of the six spacecraft and of the investigations on each spacecraft are given. The Alouette-ISIS bibliography, order alphabetically by first author's name, is contained.

  17. Robotics crosscutting program: Technology summary

    SciTech Connect

    1996-08-01

    The Office of Environmental Management (EM) is responsible for cleaning up the legacy of radioactive and chemically hazardous waste at contaminated sites and facilities throughout the U.S. Department of Energy (DOE) nuclear weapons complex, preventing further environmental contamination, and instituting responsible environmental management. Initial efforts to achieve this mission resulted in the establishment of environmental restoration and waste management programs. However, as EM began to execute its responsibilities, decision makers became aware that the complexity and magnitude of this mission could not be achieved efficiently, affordably, safely, or reasonably with existing technology. Once the need for advanced cleanup technologies became evident, EM established an aggressive, innovative program of applied research and technology development. The Office of Technology Development (OTD) was established in November 1989 to advance new and improved environmental restoration and waste management technologies that would reduce risks to workers, the public, and the environment; reduce cleanup costs; and devise methods to correct cleanup problems that currently have no solutions. In 1996, OTD added two new responsibilities - management of a Congressionally mandated environmental science program and development of risk policy, requirements, and guidance. OTD was renamed the Office of Science and Technology (OST). This documents presents information concerning robotics tank waste retrieval overview, robotic chemical analysis automation, robotics decontamination and dismantlement, and robotics crosscutting and advanced technology.

  18. Computerized Manufacturing Automation. Employment, Education, and the Workplace. Summary.

    ERIC Educational Resources Information Center

    Congress of the U.S., Washington, DC. Office of Technology Assessment.

    The application of programmable automation (PA) offers new opportunities to enhance and streamline manufacturing processes. Five PA technologies are examined in this report: computer-aided design, robots, numerically controlled machine tools, flexible manufacturing systems, and computer-integrated manufacturing. Each technology is in a relatively…

  19. 41 CFR 60-2.31 - Program summary.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 41 Public Contracts and Property Management 1 2011-07-01 2009-07-01 true Program summary. 60-2.31...-AFFIRMATIVE ACTION PROGRAMS Miscellaneous § 60-2.31 Program summary. The affirmative action program must be summarized and updated annually. The program summary must be prepared in a format which will be prescribed...

  20. 41 CFR 60-2.31 - Program summary.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 41 Public Contracts and Property Management 1 2010-07-01 2010-07-01 true Program summary. 60-2.31...-AFFIRMATIVE ACTION PROGRAMS Miscellaneous § 60-2.31 Program summary. The affirmative action program must be summarized and updated annually. The program summary must be prepared in a format which will be prescribed...

  1. A SEASAT report. Volume 1: Program summary

    NASA Technical Reports Server (NTRS)

    Pounder, E. (Editor)

    1980-01-01

    The program background and experiment objectives are summarized, and a description of the organization and interfaces of the project are provided. The mission plan and history are also included as well as user activities and a brief description of the data system. A financial and manpower summary and preliminary results of the mission are also included.

  2. HYDROLOGICAL SIMULATION PROGRAM. FORTRAN (HSPF): EXECUTIVE SUMMARY

    EPA Science Inventory

    This executive summary introduces water resource managers, engineers, and programmers to the Hydrological Simulation Program--FORTRAN and provides them with information that can help them in deciding whether HSPF would be useful and practical for them to use. HSPF uses digital co...

  3. ENVIRONMENTAL CONSIDERATIONS OF SELECTED ENERGY-CONSERVING MANUFACTURING PROCESS OPTIONS. VOLUME XVII. NITROGEN OXIDES SUMMARY REPORT

    EPA Science Inventory

    Arthur D. Little, Inc. undertook a study of the 'Environmental Consideration of Selected Energy-Conserving Manufacturing Process Options.' Some 80 industrial process options were examined in 13 industrial sectors. Results were published in 15 volumes, including a summary, industr...

  4. 78 FR 4157 - Manufactured Home Construction and Safety Standards Program

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-01-18

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT Manufactured Home Construction and Safety Standards Program AGENCY: Office of the... information: Title of Proposal: Manufactured Home Construction and Safety Standards Program. OMB...

  5. A Summary of the Manufacture of Important Inorganic Chemicals.

    ERIC Educational Resources Information Center

    Chenier, Philip J.

    1983-01-01

    Manufacture, properties, uses, and economic aspects of inorganic chemicals are discussed in an industrial chemistry course. Provided and discussed is a flowchart used in the course. The flowchart is a logical method of presenting the important features of inorganic chemicals and a summarizing their method of manufacture. (JN)

  6. Hydrogen program summary Fiscal Year 1994

    SciTech Connect

    Not Available

    1995-03-01

    The annual program summary provides stakeholders within the hydrogen community with a snapshop of important advances that have occurred in the National Hydrogen Program over the fiscal year, including industry interactions and cooperation. The document will also be used to encourage additional potential industrial partners to join the Hydrogen Program Team. Fiscal Year 1994 marked a turning point for the Hydrogen Program, with a budget that grew significantly. The focus of the program was broadened to include development of hydrogen production technologies using municipal solid waste and biomass, in addition to an increased emphasis on industrial involvement and near-term demonstration projects. In order to maintain its near- and long-term balance, the Hydrogen Program will continue with basic, fundamental research that provides the long-term, high-risk, high-payoff investment in hydrogen as an energy carrier.

  7. Short rotation woody crops program: 1982 program summary

    SciTech Connect

    Ranney, J.W.; Cushman, J.H.; Trimble, J.L.

    1982-09-01

    The general objective and overall approach of the program are discussed, and the status, specific goals, and recent results of the three major research areas are presented. The report concludes with brief summaries of the individual research projects in the program.

  8. Innovative Technology Development Program. Final summary report

    SciTech Connect

    Beller, J.

    1995-08-01

    Through the Office of Technology Development (OTD), the U.S. Department of Energy (DOE) has initiated a national applied research, development, demonstration, testing, and evaluation program, whose goal has been to resolve the major technical issues and rapidly advance technologies for environmental restoration and waste management. The Innovative Technology Development (ITD) Program was established as a part of the DOE, Research, Development, Demonstration, Testing, and Evaluation (RDDT&E) Program. The plan is part of the DOE`s program to restore sites impacted by weapons production and to upgrade future waste management operations. On July 10, 1990, DOE issued a Program Research and Development Announcement (PRDA) through the Idaho Operations Office to solicit private sector help in developing innovative technologies to support DOE`s clean-up goals. This report presents summaries of each of the seven projects, which developed and tested the technologies proposed by the seven private contractors selected through the PRDA process.

  9. SDIO producibility and manufacturing intelligent processing programs

    NASA Astrophysics Data System (ADS)

    Stottlemyer, Greg

    1992-04-01

    SDIO has to fashion a comprehensive strategy to insert the capability of an industrial base into ongoing design tradeoffs. This means that there is not only a need to determine if something can be made to the precision needed to meet system performance, but also what changes need to be made in that industry sector to develop a deterministic approach to fabrication precision components. Developing and introducing advanced production and quality control systems is part of this success. To address this situation, SDIO has developed the MODIL (Manufacturing Operations Development and Integration Labs) program. MODILs were developed into three areas: Survivable Optics, Electronics and Sensors, and Spacecraft Fabrication and Test.

  10. SDIO Producibility and Manufacturing Intelligent Processing Programs

    NASA Technical Reports Server (NTRS)

    Stottlemyer, Greg

    1992-01-01

    SDIO has to fashion a comprehensive strategy to insert the capability of an industrial base into ongoing design tradeoffs. This means that there is not only a need to determine if something can be made to the precision needed to meet system performance, but also what changes need to be made in that industry sector to develop a deterministic approach to fabrication precision components. Developing and introducing advanced production and quality control systems is part of this success. To address this situation, SDIO has developed the MODIL (Manufacturing Operations Development and Integration Labs) program. MODILs were developed into three areas: Survivable Optics, Electronics and Sensors, and Spacecraft Fabrication and Test.

  11. SUMMARY REPORT ON EMISSIONS FROM THE GLASS MANUFACTURING INDUSTRY

    EPA Science Inventory

    This project was undertaken to evaluate emissions rates from typical glass manufacturing furnaces. The effort concentrated on the container segment of the industry, however, tests were also conducted on the pressed blown, and flat glass segments of the industry. The quantitative ...

  12. MAIL LOG, program summary and specifications

    NASA Technical Reports Server (NTRS)

    Harris, D. K.

    1979-01-01

    The summary and specifications to obtain the software package, MAIL LOG, developed for the Scout Project Automatic Data System, SPADS are provided. The MAIL LOG program has four modes of operation: (1) input - putting new records into the data base; (2) revise - changing or modifying existing records in the data base; (3) search - finding special records existing in the data base; and (4) archive - store or put away existing records in the data base. The output includes special printouts of records in the data base and results from the input and search modes.

  13. Production Risk Evaluation Program (PREP) - summary

    SciTech Connect

    Kjeldgaard, E.A.; Saloio, J.H.; Vannoni, M.G.

    1997-03-01

    Nuclear weapons have been produced in the US since the early 1950s by a network of contractor-operated Department of Energy (DOE) facilities collectively known as the Nuclear Weapon Complex (NWC). Recognizing that the failure of an essential process might stop weapon production for a substantial period of time, the DOE Albuquerque Operations office initiated the Production Risk Evaluation Program (PREP) at Sandia National Laboratories (SNL) to assess quantitatively the potential for serious disruptions in the NWC weapon production process. PREP was conducted from 1984-89. This document is an unclassified summary of the effort.

  14. 2011 Annual Criticality Safety Program Performance Summary

    SciTech Connect

    Andrea Hoffman

    2011-12-01

    The 2011 review of the INL Criticality Safety Program has determined that the program is robust and effective. The review was prepared for, and fulfills Contract Data Requirements List (CDRL) item H.20, 'Annual Criticality Safety Program performance summary that includes the status of assessments, issues, corrective actions, infractions, requirements management, training, and programmatic support.' This performance summary addresses the status of these important elements of the INL Criticality Safety Program. Assessments - Assessments in 2011 were planned and scheduled. The scheduled assessments included a Criticality Safety Program Effectiveness Review, Criticality Control Area Inspections, a Protection of Controlled Unclassified Information Inspection, an Assessment of Criticality Safety SQA, and this management assessment of the Criticality Safety Program. All of the assessments were completed with the exception of the 'Effectiveness Review' for SSPSF, which was delayed due to emerging work. Although minor issues were identified in the assessments, no issues or combination of issues indicated that the INL Criticality Safety Program was ineffective. The identification of issues demonstrates the importance of an assessment program to the overall health and effectiveness of the INL Criticality Safety Program. Issues and Corrective Actions - There are relatively few criticality safety related issues in the Laboratory ICAMS system. Most were identified by Criticality Safety Program assessments. No issues indicate ineffectiveness in the INL Criticality Safety Program. All of the issues are being worked and there are no imminent criticality concerns. Infractions - There was one criticality safety related violation in 2011. On January 18, 2011, it was discovered that a fuel plate bundle in the Nuclear Materials Inspection and Storage (NMIS) facility exceeded the fissionable mass limit, resulting in a technical safety requirement (TSR) violation. The TSR limits fuel

  15. 48 CFR 235.006-70 - Manufacturing Technology Program.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 48 Federal Acquisition Regulations System 3 2011-10-01 2011-10-01 false Manufacturing Technology... CONTRACTING 235.006-70 Manufacturing Technology Program. In accordance with 10 U.S.C. 2521(d), for acquisitions under the Manufacturing Technology Program— (a) Award all contracts using competitive...

  16. 48 CFR 235.006-70 - Manufacturing Technology Program.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Manufacturing Technology... CONTRACTING 235.006-70 Manufacturing Technology Program. In accordance with 10 U.S.C. 2521(d), for acquisitions under the Manufacturing Technology Program— (a) Award all contracts using competitive...

  17. 48 CFR 235.006-70 - Manufacturing Technology Program.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 48 Federal Acquisition Regulations System 3 2013-10-01 2013-10-01 false Manufacturing Technology... CONTRACTING 235.006-70 Manufacturing Technology Program. In accordance with 10 U.S.C. 2521(d), for acquisitions under the Manufacturing Technology Program— (a) Award all contracts using competitive...

  18. 48 CFR 235.006-70 - Manufacturing Technology Program.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 3 2012-10-01 2012-10-01 false Manufacturing Technology... CONTRACTING 235.006-70 Manufacturing Technology Program. In accordance with 10 U.S.C. 2521(d), for acquisitions under the Manufacturing Technology Program— (a) Award all contracts using competitive...

  19. 48 CFR 235.006-70 - Manufacturing Technology Program.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 48 Federal Acquisition Regulations System 3 2014-10-01 2014-10-01 false Manufacturing Technology... CONTRACTING 235.006-70 Manufacturing Technology Program. In accordance with 10 U.S.C. 2521(d), for acquisitions under the Manufacturing Technology Program— (a) Award all contracts using competitive...

  20. USFOE: Extended Summary - Lithium ion batteries and their manufacturing challenges

    SciTech Connect

    Daniel, Claus

    2014-01-01

    There is no one lithium ion battery. With the variety of materials and electrochemical couples at our disposal as shown in the previous talks, we have the opportunity to design battery cells specific for their applications. Such applications require optimization of voltage, state of charge utilization, lifetime needs, and safety considerations. Electrochemical couples allow for designing power and energy ratios and available energy for the application. Integration in a large format cell requires optimized roll to roll electrode manufacturing and active material utilization. Electrodes are coated on a current collector in a composite structure comprised of active material, binders, and conductive additives which requires careful control of colloidal chemistry, adhesion, and solidification. These added inactive materials and the cell packaging reduce energy density. Degree of porosity and compaction in the electrode can impede or enhance battery performance. Pathways are explored to bring batteries from currently commercially available 100Wh/kg and 200Wh/L at $500/kWh to 250Wh/kg and 400Wh/L at $125/kWh.

  1. Summary of NDE of additive manufacturing efforts in NASA

    NASA Astrophysics Data System (ADS)

    Waller, Jess M.; Saulsberry, Regor L.; Parker, Bradford H.; Hodges, Kenneth L.; Burke, Eric R.; Taminger, Karen M.

    2015-03-01

    One of the major obstacles slowing the acceptance of parts made by additive manufacturing (AM) in NASA applications is the lack of a broadly accepted materials and process quality systems; and more specifically, the lack of adequate nondestructive evaluation (NDE) processes integrated into AM. Matching voluntary consensus standards are also needed to control the consistency of input materials, process equipment, process methods, finished part properties, and how those properties are characterized. As for nondestructive characterization, procedures are needed to interrogate features unique to parts made by AM, such as fine-scale porosity, deeply embedded flaws, complex part geometry, and intricate internal features. The NDE methods developed must be tailored to meet materials, design and test requirements encountered throughout the part life cycle, whether during process optimization, real-time process monitoring, finished part qualification and certification (especially of flight hardware), or in situ health monitoring. Restated, individualized process/product-specific NDE methods are needed to satisfy NASA's various quality assurance requirements. To date, only limited data have been acquired by NASA on parts made by AM. This paper summarizes the NASA AM effort, highlights available NDE data, and outlines the approach NASA is taking to apply NDE to its various AM efforts.

  2. The Impact of Intrapreneurial Programs on Fortune 500 Manufacturing Firms.

    ERIC Educational Resources Information Center

    Marcus, Melissa H.; Tesolowski, Dennis G.; Isbell, Clinton H.

    2000-01-01

    A survey of 100 manufacturing firms in 10 Standard Industrial Classification areas found that intrapreneurial programs did not significantly affect sales, profits, or returns to investors. Electronics and computer companies and the most dominant intrapreneurial programs. (SK)

  3. NASA Game Changing Development Program Manufacturing Innovation Project

    NASA Technical Reports Server (NTRS)

    Tolbert, Carol; Vickers, John

    2011-01-01

    This presentation examines the new NASA Manufacturing Innovation Project. The project is a part of the Game Changing Development Program which is one element of the Space Technology Programs Managed by Office of the Chief Technologist. The project includes innovative technologies in model-based manufacturing, digital additive manufacturing, and other next generation manufacturing tools. The project is also coupled with the larger federal initiatives in this area including the National Digital Engineering and Manufacturing Initiative and the Advanced Manufacturing Partnership. In addition to NASA, other interagency partners include the Department of Defense, Department of Commerce, NIST, Department of Energy, and the National Science Foundation. The development of game-changing manufacturing technologies are critical for NASA s mission of exploration, strengthening America s manufacturing competitiveness, and are highly related to current challenges in defense manufacturing activities. There is strong consensus across industry, academia, and government that the future competitiveness of U.S. industry will be determined, in large part, by a technologically advanced manufacturing sector. This presentation highlights the prospectus of next generation manufacturing technologies to the challenges faced NASA and by the Department of Defense. The project focuses on maturing innovative/high payoff model-based manufacturing technologies that may lead to entirely new approaches for a broad array of future NASA missions and solutions to significant national needs. Digital manufacturing and computer-integrated manufacturing "virtually" guarantee advantages in quality, speed, and cost and offer many long-term benefits across the entire product lifecycle. This paper addresses key enablers and emerging strategies in areas such as: Current government initiatives, Model-based manufacturing, and Additive manufacturing.

  4. Geothermal direct heat applications program summary

    SciTech Connect

    1982-08-01

    In 1978, the Department of Energy Division of Geothermal and Hydropower Technologies initiated a program to accelerate the direct use of geothermal energy, in which 23 projects were selected. The projects, all in the western part of the US, cover the use of geothermal energy for space conditioning (heating and cooling) and agriculture (aquaculture and greenhouses). Initially, two projects were slated for industrial processing; however, because of lack of geothermal resources, these projects were terminated. Of the 23 projects, seven were successfully completed, ten are scheduled for completion by the end of 1983, and six were terminated for lack of resources. Each of the projects is being documented from its inception through planning, drilling, and resource confirmation, design, construction, and one year of monitoring. The information is being collected, evaluated, and will be reported. Several reports will be produced, including detailed topical reports on economics, institutional and regulatory problems, engineering, and a summary final report. To monitor progress and provide a forum for exchange of information while the program is progressing, semiannual or annual review meetings have been held with all project directors and lead engineers for the past four years. This is the sixth meeting in that series. Several of the projects which have been terminated are not included this year. Overall, the program has been very successful. Valuable information has been gathered. problems have been encountered and resolved concerning technical, regulatory, and institutional constraints. Most projects have been proven to be economical with acceptable pay-back periods. Although some technical problems have emerged, they were resolved with existing off-the-shelf technologies and equipment. The risks involved in drilling for the resource, the regulatory constraints, the high cost of finance, and large front-end cost remain the key obstacles to the broad development of

  5. Summary of the Formative Evaluation Report of Self Incorporated Programs.

    ERIC Educational Resources Information Center

    Rockman, Saul; Auh, Taiksup

    Self Incorporated is a 15-program television/film series designed to stimulate classroom discussion of problems and issues of early adolescence. This document provides an overall summary of a formative evaluation project and summary results of the evaluations of each of eight programs in the series. (CH)

  6. Ocean energy program summary. Volume 2: Research summaries

    NASA Astrophysics Data System (ADS)

    1990-01-01

    The oceans are the world's largest solar energy collector and storage system. Covering 71 percent of the earth's surface, this stored energy is realized as waves, currents, and thermal salinity gradients. The purpose of the Federal Ocean Energy Technology (OET) Program is to develop techniques that harness this ocean energy in a cost effective and environmentally acceptable manner. The OET Program seeks to develop ocean energy technology to a point where the commercial sector can assess whether applications of the technology are viable energy conversion alternatives or supplements to systems. Past studies conducted by the U.S. Department of Energy (DOE) have identified ocean thermal energy conversion (OTEC) as the largest potential contributor to United States energy supplies from the ocean resource. As a result, the OET Program concentrates on research to advance OTEC technology. Current program emphasis has shifted to open-cycle OTEC power system research because the closed-cycle OTEC system is at a more advanced stage of development and has already attracted industrial interest. During FY 1989, the OET Program focused primarily on the technical uncertainties associated with near-shore open-cycle OTEC systems ranging in size from 2 to 15 MW(sub e). Activities were performed under three major program elements: thermodynamic research and analysis, experimental verification and testing, and materials and structures research. These efforts addressed a variety of technical problems whose resolution is crucial to demonstrating the viability of open-cycle OTEC technology. This publications is one of a series of documents on the Renewable Energy programs sponsored by the U.S. Department of Energy. An overview of all the programs is available, entitled Programs in Renewable Energy.

  7. Executive summary of the Cryofracture demonstration program

    SciTech Connect

    Loomis, G.; Osborne, D.; Ancho, M.

    1991-09-01

    This report provides an executive summary of the Cryofracture demonstration program performed at Nuclear Remedial Technologies Corporation under contract to EG G Idaho, Inc., for the Department of Energy (DOE). Cryofracture is a size-reducing process whereby objects are frozen whereby objects are frozen to liquid nitrogen temperatures and crushed in a large hydraulic press. Material at the cryogenic temperatures have low ductility and are easily size reduced by fracturing. The main application being investigated for the DOE is for retrieved buried and stored transuranic (TRU) waste. Six 55-gallon drums and six 2 ft {times} 2 ft {times} 8 ft boxes containing simulated waste with tracers were subjected to the Cryofracture process. Data was obtained on (a) cool-down time, (b) yield strength of the containers, (c) size distribution of the waste before and after the Cryofracture process, (d) volume reduction of the waste, and (e) sampling of air and surface dusts for spread of tracers to evaluate potential contamination spread. The Cryofracture process was compared to conventional shredders and detailed cost estimates were established for construction of a Cryofracture facility at the Idaho National Engineering Laboratory. Although cost estimates for conventional shredding are higher for Cryofracture, the potential for fire and explosion during conventional shredding would incur additional costs to preclude these events. These additional costs are unknown and would require considerable research and development. 4 refs., 6 figs., 7 tabs.

  8. A normative price for a manufactured product: The SAMICS methodology. Volume 1: Executive summary

    NASA Technical Reports Server (NTRS)

    Chamberlain, R. G.

    1979-01-01

    A summary for the Solar Array Manufacturing Industry Costing Standards report contains a discussion of capabilities and limitations, a non-technical overview of the methodology, and a description of the input data which must be collected. It also describes the activities that were and are being taken to ensure validity of the results and contains an up-to-date bibliography of related documents.

  9. Automated Manufacturing/Robotics Technology: Certificate and Associate Degree Programs.

    ERIC Educational Resources Information Center

    McQuay, Paul L.

    A description is provided of the Automated Manufacturing/Robotics program to be offered at Delaware County Community College beginning in September 1984. Section I provides information on the use of reprogramable industrial robots in manufacturing and the rapid changes in production that can be effected through the application of automated…

  10. Marketing manufactured housing under the ''Super Good Cents'' Program

    SciTech Connect

    Mohler, B.L.; Smith, S.A.

    1986-01-01

    The objective of this study is to propose a strategy for including manufactured housing (MH) in Bonneville Power Administration's Super Good Cents (SGC) Program. This report presents information on the site-built SGC program, the characterization of MH consumers, the options for including MH in the SGC program, and the recommendations for including MHs in the SGC program. The purposed strategy for including MHs in the SGC program is designed to reduce risks to manufacturers and dealers, stimulate demand, and allow for maximum flexibility.

  11. Materials/manufacturing element of the Advanced Turbine Systems Program

    SciTech Connect

    Karnitz, M.A.; Holcomb, R.S.; Wright, I.G.

    1995-10-01

    The technology based portion of the Advanced Turbine Systems Program (ATS) contains several subelements which address generic technology issues for land-based gas-turbine systems. One subelement is the Materials/Manufacturing Technology Program which is coordinated by DOE-Oak Ridge Operations and Oak Ridge National Laboratory (ORNL). The work in this subelement is being performed predominantly by industry with assistance from universities and the national laboratories. Projects in this subelement are aimed toward hastening the incorporation of new materials and components in gas turbines. A materials/manufacturing plan was developed in FY 1994 with input from gas turbine manufacturers, materials suppliers, universities, and government laboratories. The plan outlines seven major subelements which focus on materials issues and manufacturing processes. Work is currently under way in four of the seven major subelements. There are now major projects on coatings and process development, scale-up of single crystal airfoil manufacturing technology, materials characterization, and technology information exchange.

  12. 40 CFR 35.903 - Summary of construction grant program.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 1 2011-07-01 2011-07-01 false Summary of construction grant program. 35.903 Section 35.903 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GRANTS AND OTHER FEDERAL ASSISTANCE STATE AND LOCAL ASSISTANCE Grants for Construction of Treatment Works-Clean Water Act § 35.903 Summary of construction grant...

  13. JTEC/WTEC annual report and program summary: 1993/94

    NASA Technical Reports Server (NTRS)

    Holdridge, Geoffrey M. (Editor)

    1994-01-01

    The JTEC/WTEC (Japanese Technology Evaluation Center/World Technology Evaluation Center) Program at Loyola College is overviewed. A review of activities for 1993 and early 1994 is discussed along with plans for the following year. The bulk of the report consists of the summaries of completed projects in Information and Communication Technology; Materials; Manufacturing and Construction; Aeronautics, Space, and Ocean Technology; Energy; and Biotechnology.

  14. Geothermal Energy Research and Development Program; Project Summaries

    SciTech Connect

    1994-03-01

    This is an internal DOE Geothermal Program document. This document contains summaries of projects related to exploration technology, reservoir technology, drilling technology, conversion technology, materials, biochemical processes, and direct heat applications. [DJE-2005

  15. Agriculture and Food Processes Branch program summary document

    SciTech Connect

    Not Available

    1981-06-01

    The food industry, its energy consumption, and its energy conservation targets are discussed. Activities of the Agriculture and Food Processes Branch are described. Summaries of research, development, and demonstration programs of the Branch are given. The programs are categorized into the following: energy integrated farm systems; irrigation systems; crop drying systems; fertilizer; dairy and milk processing; meat processing; sugar processing; citrus processing; ethanol production; food processing efficiency systems; and food sterilization. Summaries are presented of 26 completed projects. (MCW)

  16. Parent Evaluation Form Summary - 1970 Summer Reading Program.

    ERIC Educational Resources Information Center

    Kaplan, Steven P.

    As part of the evaluation of the Southwest Regional Laboratory (SWRL) 1970 Summer Reading Program, a Parent Evaluation Form was distributed at the conclusion of the program. This form was sent home with 342 pupils whose parents were invited to participate with them in the program. The summary given in this report includes information received…

  17. Summary of the STIS Cycle 19 Calibration Program

    NASA Astrophysics Data System (ADS)

    Roman-Duval, Julia; Ely, Justin; Aloisi, Alessandra; Oliveira, Cristina; Proffitt, Charles; Hernandez, Svea; Mason, Elena; Sonnetrucker, Paule; Wolfe, Michael; Long, Chris; DiFelice, Audrey; Bostroem, Azalee K.; Holland, Stephen; Lockwood, Sean; Cox, Colin; Wheeler, Thomas

    2014-11-01

    We summarize the Cycle 19 calibration program for the Space Telescope Imaging Spectrograph (STIS) on the Hubble Space Telescope, covering the time period November 2011 through October 2012. We give an overview of the whole program, and status summaries for each of the individual proposals comprising the program.

  18. Summary of the STIS Cycle 21 Calibratio Program

    NASA Astrophysics Data System (ADS)

    Sana, Hugues; Fox, Andrew; Roman-Duval, Julia; Ely, Justin; Cox, Colin; DiFelice, Audrey; Hernandez, Svea; Lockwood, Sean; Oliveira, Cristina; Penton, Steve; Proffitt, Charles; Sahnow, David; Sonnentrucker, Paule; Taylor, Jo; Welty, Alan D.; Wheeler, Thomas

    2015-09-01

    We summarize the Cycle 21 calibration program for the Space Telescope Imaging Spectrograph (STIS) on the Hubble Space Telescope covering the time period November 2013 through October 2014. We give an overview of the whole program, and status summaries for each of the individual proposals comprising the program.

  19. Summary of the STIS Cycle 20 Calibration Program

    NASA Astrophysics Data System (ADS)

    Roman-Duval, Julia; Ely, Justin; Cox, Colin; Hernandez, Svea; Lockwood, Sean; Oliveira, Cristina; Proffitt, Charles; Sana, Hugues; Sonnentrucker, Paule; Wheeler, Thomas

    2015-09-01

    We summarize the Cycle 20 calibration program for the Space Telescope Imaging Spectrograph (STIS) on the Hubble Space Telescope covering the time period November 2012 through October 2013. We give an overview of the whole program, and status summaries for each of the individual proposals comprising the program.

  20. Two mathematical programming models of cheese manufacture.

    PubMed

    Burke, J A

    2006-02-01

    The standardization problem faced by cheese makers is formulated as a nonlinear programming problem using the assumptions of the Van Slyke cheese yield formula. The objective function of the model is to minimize the net cost of producing a given quantity of cheese subject to a set of production constraints. An approximation of the standardization problem formulated as a linear programming problem is also presented. Two different approaches to finding a solution are provided. The model is implemented in Microsoft Excel and solved with the standard add-in solver available in that program. An example is provided to contrast the difference between the nonlinear programming and its linear approximation, and a second example is used to illustrate the yield implications of ultrafiltered milk protein products in Cheddar cheese production. Additionally, a method for pricing inputs using the sensitivity analysis generated by the solver is demonstrated. PMID:16428648

  1. National Survey of Computer Aided Manufacturing in Industrial Technology Programs.

    ERIC Educational Resources Information Center

    Heidari, Farzin

    The current status of computer-aided manufacturing in the 4-year industrial technology programs in the United States was studied. All industrial technology department chairs were mailed a questionnaire divided into program information, equipment information, and general comments sections. The questionnaire was designed to determine the subjects…

  2. Program Evolves from Basic CAD to Total Manufacturing Experience

    ERIC Educational Resources Information Center

    Cassola, Joel

    2011-01-01

    Close to a decade ago, John Hersey High School (JHHS) in Arlington Heights, Illinois, made a transition from a traditional classroom-based pre-engineering program. The new program is geared towards helping students understand the entire manufacturing process. Previously, a JHHS student would design a project in computer-aided design (CAD) software…

  3. Physician Assistant Programs. Summary. Third Revised Edition.

    ERIC Educational Resources Information Center

    Health Careers of Ohio, Columbus.

    The document provides information on the name of the program, the institution, prerequisites, length of course, and certificate or degree offered for 81 programs for the training of physician assistants as part of Operation MEDIHC (Military Experience Directed Into Health Careers). Fifty-three programs are in primary care; the remaining 28 are…

  4. Youth Gang Programs and Strategies. OJJDP Summary.

    ERIC Educational Resources Information Center

    Howell, James C.

    This document draws on more than 50 years of gang program evaluations to summarize what has been learned about: (1) prevention programs, including early childhood, school-based, and afterschool initiatives; (2) intervention programs, including those that work to create violence-free zones, establish gang summits and truces, and rehabilitate gang…

  5. 76 FR 43983 - Request for Information on How To Structure Proposed New Program: Advanced Manufacturing...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-07-22

    ... Program: Advanced Manufacturing Technology Consortia (AMTech) AGENCY: National Institute of Standards and... structure a new public-private partnership program, the Advanced Manufacturing Technology Consortia (AMTech... or newly created industry-led consortia to develop precompetitive enabling manufacturing...

  6. Automotive Stirling Engine Development Program. RESD Summary report

    SciTech Connect

    Not Available

    1984-05-01

    This is the final report compiling a summary of the information presented and discussed at the May 1983 Automotive Stirling Engine (AES) Reference Engine System Design (RESD) review held at the NASA Lewis Research Center. The design of the engine and its auxiliaries and controls is described. Manufacturing costs in production quantity are also presented. Engine system performance predictions are discussed and vehicle integration is developed, along with projected fuel economy levels.

  7. IND Regulatory & Manufacturing Resources - Cancer Imaging Program

    Cancer.gov

    The Cancer Imaging Program has been creating Investigational New Drug Applications (IND) for imaging agents in order to engage in multi-center clinical trials of these materials. A subset of the documents filed is being made available to the research community to implement routine synthesis of tracers at their own facilities and to assist investigators with the filing of their own INDs. The first of these document sets is for F-18 fluorothymidine (FLT).

  8. Nickel-hydrogen Cell Test Program Summary

    NASA Technical Reports Server (NTRS)

    Mueller, V. C.

    1985-01-01

    Three prototype 50 ampere-hour (Ah) nickel-hydrogen cells of the Air Force Wright Aeronautical Laboratories (AWFAL) design were cycled to failure. A summary of the life cycling tests and failure analyses of the cells are presented. The cells were cycled in a simulated low earth orbit regime at depths of discharge ranging from 25 to 80 percent. Trend data, such as end of discharge voltage and cell capacity, was recorded during test. Cells 1, 2, and 3 completed 17167, 2473, and 10080 charge/discharge cycles, respectively, prior to failure. All failed due to internal shorts, and were disassembled to determine cause of failure.

  9. Summary of the COS Cycle 20 Calibration Program

    NASA Astrophysics Data System (ADS)

    Roman-Duval, Julia; Aloisi, Alessandra; Bostroem, K. Azalee; Ely, Justin; Holland, Stephen; Lockwood, Sean; Oliveira, Cristina; Penton, Steven; Proffitt, Charles; Sahnow, David; Sonnentrucker, Paule; Welty, Alan D.; Wheeler, Thomas

    2015-06-01

    We summarize the Cycle 20 calibration program for the Cosmic Origins Spectrograph (COS) on the Hubble Space Telescope, covering the time period from November 2012 through October 2013. We give an overview of the Calibration plan and status summaries for each of the individual proposals comprising the C20 Calibration program.

  10. Summary of the COS Cycle 21 Calibration Program

    NASA Astrophysics Data System (ADS)

    Sana, Hugues; Fox, Andrew; Roman-Duval, Julia; Ely, Justin; Bostroem, K. Azalee; Lockwood, Sean; Oliveira, Cristina; Penton, Steve; Proffitt, Charles; Sahnow, David; Sonnentrucker, Paule; Welty, Alan D.; Wheeler, Thomas

    2015-09-01

    We summarize the Cycle 21 calibration program for the Cosmic Origins Spectrograph (COS) on the Hubble Space Telescope, covering the time period from November 2013 through October 2014. We give an overview of the Calibration plan and status summaries for each of the individual proposals comprising the C21 Calibration program.

  11. Northwest Energy Efficient Manufactured Housing Program Specification Development

    SciTech Connect

    Hewes, Tom; Peeks, Brady

    2013-02-01

    The DOE research team Building America Partnership for Improved Residential Construction (BA-PIRC), Bonneville Power Administration (BPA), and Northwest Energy Works (NEW), the current Northwest Energy Efficient Manufactured Home Program (NEEM) program administrator, collaborated to research a new specification that would reduce the energy requirements of a NEEM home.This research identified and developed combinations of cost-effective high performance building assemblies and mechanical systems that can readily can be deployed in the manufacturing setting that reduce energy used for space conditioning, water heating and lighting by 50% over the present NEEM specifications.

  12. Materials/manufacturing element of the Advanced Turbine System Program

    SciTech Connect

    Karnitz, M.A.; Devan, J.H.; Holcomb, R.S.; Ferber, M.K.; Harrison, R.W.

    1994-08-01

    One of the supporting elements of the Advanced Turbine Systems (ATS) Program is the materials/manufacturing technologies task. The objective of this element is to address critical materials issues for both industrial and utility gas turbines. DOE Oak Ridge Operations Office (ORO) will manage this element of the program, and a team from DOE-ORO and Oak Ridge National Laboratory is coordinating the planning for the materials/manufacturing effort. This paper describes that planning activity which is in the early stages.

  13. SUNY Youth Internship Program: A Summary Review.

    ERIC Educational Resources Information Center

    Winter, Gene M.; Fadale, LaVerna M.

    A Youth Internship Program (YIP) has been developed at seven community colleges of the State University of New York (SUNY) to improve the employability potential of unemployed, out-of-school, economically disadvantaged youth between 16 and 21 years of age. Components of the seven programs examined differ, but all address six main activities:…

  14. Ron Brown Scholar Program. Evaluation Summary

    ERIC Educational Resources Information Center

    Broton, Katie; Mueller, Dan

    2009-01-01

    The Ron Brown Scholar Program aims to be a major force in producing this nation's next generation of leaders by providing academic scholarships, service opportunities, and leadership experiences to exemplary young African Americans. The program is highly selective, with several hundred applicants per scholarship awarded. Students are selected…

  15. The Interdependent Learning Model. Program Summary.

    ERIC Educational Resources Information Center

    Far West Lab. for Educational Research and Development, Berkeley, CA.

    This document is the sixth in a series of 12 early childhood program descriptions compiled by the Far West Laboratory for Educational Research and Development. The program described here is the Interdependent Learning Model located at the Institute for Developmental Studies at New York University in New York City. The Interdependent Learning Model…

  16. Effective Beginning Reading Programs. [Educator's Summary

    ERIC Educational Resources Information Center

    Center for Data-Driven Reform in Education (NJ3), 2009

    2009-01-01

    What beginning reading programs have been proven to help students in grades K-1 to succeed? To find out, this review summarizes evidence on four types of programs designed to improve beginning reading achievement: (1) Reading Curricula (Curr), such as "Open Court Reading," "Reading Street," and other standard and alternative textbooks; (2)…

  17. A review of the Technologies Enabling Agile Manufacturing program

    SciTech Connect

    Gray, W.H.; Neal, R.E.; Cobb, C.K.

    1996-10-01

    Addressing a technical plan developed in consideration with major US manufacturers, software and hardware providers, and government representatives, the Technologies Enabling Agile Manufacturing (TEAM) program is leveraging the expertise and resources of industry, universities, and federal agencies to develop, integrate, and deploy leap-ahead manufacturing technologies. One of the TEAM program`s goals is to transition products from design to production faster, more efficiently, and at less cost. TEAM`s technology development strategy also provides all participants with early experience in establishing and working within an electronic enterprise that includes access to high-speed networks and high-performance computing and storage systems. The TEAM program uses the cross-cutting tools it collects, develops, and integrates to demonstrate and deploy agile manufacturing capabilities for three high-priority processes identified by industry: material removal, sheet metal forming, electro-mechanical assembly. This paper reviews the current status of the TEAM program with emphasis upon TEAM`s information infrastructure.

  18. Nuclear Waste Management Program summary document, FY 1981

    SciTech Connect

    Meyers, Sheldon

    1980-03-01

    The Nuclear Waste Management Program Summary Document outlines the operational and research and development (R and D) activities of the Office of Nuclear Waste Management (NEW) under the Assistant Secretary for Nuclear Energy, US Department of Energy (DOE). This document focuses on the current and planned activities in waste management for FY 1981. This Program Summary Document (PSD) was prepared in order to explain the Federal nuclear waste management and spent fuel storage programs to Congress and its committees and to interested members of the public, the private sector, and the research community. The national energy policy as it applies to waste management and spent fuel storage is presented first. The program strategy, structure, budget, management approach, and public participation programs are then identified. The next section describes program activities and outlines their status. Finally, the applicability of departmental policies to NEW programs is summarized, including field and regional activities, commercialization plans, and environmental and socioeconomic implications of waste management activities, and international programs. This Nuclear Waste Management Program Summary Document is meant to serve as a guide to the progress of R and D and other energy technology programs in radioactive waste management. The R and D objective is to provide the Nation with acceptable solutions to short- and long-term management problems for all forms of radioactive waste and spent fuel.

  19. Hallam fuel decladding. Program summary report

    SciTech Connect

    Dennison, W.F.

    1980-04-01

    This report summarizes the program of decladding the 150 Hallam fuel assemblies, removal of the sodium, and the packaging and shipment of the recovered fuel to Savannah River for eventual reprocessing.

  20. Advanced Rotorcraft Transmission (ART) program summary

    NASA Technical Reports Server (NTRS)

    Krantz, T. L.; Kish, J. G.

    1992-01-01

    The Advanced Rotorcraft Transmission (ART) Program was initiated to advance the state of the art for rotorcraft transmissions. The goal of the ART Program was to develop and demonstrate the technologies needed to reduce transmission weight by 25 pct. and reduce noise by 10 dB while obtaining a 5000 hr 'mean time between failure'. The research done under the ART Program is summarized. A split path design was selected as best able to meet the program goals. Key part technologies needed for this design were identified, studied, and developed. Two of these technologies are discussed in detail: the load sharing of split path designs including the use of a compliant elastomeric torque splitter and the application of a high ratio, low pitch line velocity gear mesh. Development of an angular contact spherical roller bearing, transmission error analysis, and fretting fatigue testing are discussed. The technologies for a light weight, quiet, and reliable rotorcraft transmission were demonstrated.

  1. Hawaii Deep Water Cable Program: Executive Summary

    SciTech Connect

    1990-09-01

    The Hawaii Deep Water Cable Program has succeeded unequivocally in determining the feasibility of deploying a submarine power cable system between the islands of Hawaii and Oahu. Major accomplishments of the program include designing, fabricating and testing an appropriate power cable, developing an integrated system to control all aspects of the cable laying operation, and testing all deployment systems at sea in the most challenging sections of the route.

  2. Summary of emissions reduction technology programs

    NASA Technical Reports Server (NTRS)

    Niedzwiecki, R. W.

    1977-01-01

    The NASA emissions reduction contract programs for EPA aircraft engine classes P2 (turboshaft engines), T1 (jet engines with thrust under 8000 lb), T4 (JT8D) engines), and T2 (jet engines with thrust over 8000 lb) are discussed. The most important aspects of these programs, the commonality of approaches used, the test results, and assessments regarding applications of the derived technology are summarized.

  3. Northwest Energy Efficient Manufactured Housing Program: High Performance Manufactured Home Prototyping and Construction Development

    SciTech Connect

    Hewes, T.; Peeks, B.

    2013-11-01

    The Building America Partnership for Improved Residential Construction, the Bonneville Power Administration (BPA), and Northwest Energy Works (NEW), the current Northwest Energy Efficient Manufactured Housing Program (NEEM) administrator, have been collaborating to conduct research on new specifications that would improve on the energy requirements of a NEEM home. In its role as administrator, NEW administers the technical specs, performs research and engineering analysis, implements ongoing construction quality management procedures, and maintains a central database with home tracking. This project prototyped and assessed the performances of cost-effective high performance building assemblies and mechanical systems that are not commonly deployed in the manufacturing setting. The package of measures is able to reduce energy used for space conditioning, water heating and lighting by 50 percent over typical manufactured homes produced in the northwest.

  4. Northwest Energy Efficient Manufactured Housing Program: High Performance Manufactured Home Prototyping and Construction Development

    SciTech Connect

    Hewes, Tom; Peeks, Brady

    2013-11-01

    The Building America Partnership for Improved Residential Construction, the Bonneville Power Administration (BPA), and Northwest Energy Works (NEW), the current Northwest Energy Efficient Manufactured Housing Program (NEEM) administrator, have been collaborating to conduct research on new specifications that would improve on the energy requirements of a NEEM home. In its role as administrator, NEW administers the technical specs, performs research and engineering analysis, implements ongoing construction quality management procedures, and maintains a central database with home tracking. This project prototyped and assessed the performances of cost-effective high performance building assemblies and mechanical systems that are not commonly deployed in the manufacturing setting. The package of measures is able to reduce energy used for space conditioning, water heating and lighting by 50% over typical manufactured homes produced in the northwest.

  5. Manufacturing Production: An Evaluation Report for the Occupational Exploration Program.

    ERIC Educational Resources Information Center

    Altschuld, James W.; And Others

    The evaluation report is one of seven produced for the Occupational Exploration Program (OEP), a series of simulated occupational experiences designed for junior high school students. Describing the pilot testing of the simulation dealing with manufacturing production, the report contains sections describing the simulation context, evaluation…

  6. Energy Engineering Analysis Program (EEAP), Worms Military Community, West Germany, revised executive summary. Executive summary

    SciTech Connect

    1986-08-01

    This document is the Executive Summary of the Phase II Energy Report for the Energy Engineering Analysis Program (EEAP) for the Worms, West Germany Military Community. The purpose of this document is to present analysis of potential energy conservation projects at each of the sites.

  7. Renewable energy water supply - Mexico program summary

    SciTech Connect

    Foster, R.

    1997-12-01

    This paper describes a program directed by the US Agency for International Development and Sandia National Laboratory which installed sustainable energy sources in the form of photovoltaic modules and wind energy systems in rural Mexico to pump water and provide solar distillation services. The paper describes the guidelines which appeared most responsible for success as: promote an integrated development program; install quality systems that develop confidence; instill local project ownership; train local industry and project developers; develop a local maintenance infrastructure; provide users training and operations guide; develop clear lines of responsibilities for system upkeep. The paper emphasizes the importance of training. It also presents much collected data as to the characteristics and performance of the installed systems.

  8. Robotics Technology Crosscutting Program. Technology summary

    SciTech Connect

    1995-06-01

    The Robotics Technology Development Program (RTDP) is a needs-driven effort. A length series of presentations and discussions at DOE sites considered critical to DOE`s Environmental Restoration and Waste Management (EM) Programs resulted in a clear understanding of needed robotics applications toward resolving definitive problems at the sites. A detailed analysis of the resulting robotics needs assessment revealed several common threads running through the sites: Tank Waste Retrieval (TWR), Contaminant Analysis Automation (CAA), Mixed Waste Operations (MWO), and Decontamination and Dismantlement (D and D). The RTDP Group also realized that some of the technology development in these four areas had common (Cross Cutting-CC) needs, for example, computer control and sensor interface protocols. Further, the OTD approach to the Research, Development, Demonstration, Testing, and Evaluation (RDDT and E) process urged an additional organizational breakdown between short-term (1--3 years) and long-term (3--5 years) efforts (Advanced Technology-AT). These factors lead to the formation of the fifth application area for Crosscutting and Advanced Technology (CC and AT) development. The RTDP is thus organized around these application areas -- TWR, CAA, MWO, D and D, and CC and AT -- with the first four developing short-term applied robotics. An RTDP Five-Year Plan was developed for organizing the Program to meet the needs in these application areas.

  9. AST Composite Wing Program: Executive Summary

    NASA Technical Reports Server (NTRS)

    Karal, Michael

    2001-01-01

    The Boeing Company demonstrated the application of stitched/resin infused (S/RFI) composite materials on commercial transport aircraft primary wing structures under the Advanced Subsonic technology (AST) Composite Wing contract. This report describes a weight trade study utilizing a wing torque box design applicable to a 220-passenger commercial aircraft and was used to verify the weight savings a S/RFI structure would offer compared to an identical aluminum wing box design. This trade study was performed in the AST Composite Wing program, and the overall weight savings are reported. Previous program work involved the design of a S/RFI-base-line wing box structural test component and its associated testing hardware. This detail structural design effort which is known as the "semi-span" in this report, was completed under a previous NASA contract. The full-scale wing design was based on a configuration for a MD-90-40X airplane, and the objective of this structural test component was to demonstrate the maturity of the S/RFI technology through the evaluation of a full-scale wing box/fuselage section structural test. However, scope reductions of the AST Composite Wing Program pre-vented the fabrication and evaluation of this wing box structure. Results obtained from the weight trade study, the full-scale test component design effort, fabrication, design development testing, and full-scale testing of the semi-span wing box are reported.

  10. Ocean Margins Programs, Phase I research summaries

    SciTech Connect

    Verity, P.

    1994-08-01

    During FY 1992, the DOE restructured its regional coastal-ocean programs into a new Ocean Margins Program (OMP), to: Quantify the ecological and biogeochemical processes and mechanisms that affect the cycling, flux, and storage of carbon and other biogenic elements at the land/ocean interface; Define ocean-margin sources and sinks in global biogeochemical cycles, and; Determine whether continental shelves are quantitatively significant in removing carbon dioxide from the atmosphere and isolating it via burial in sediments or export to the interior ocean. Currently, the DOE Ocean Margins Program supports more than 70 principal and co-principal investigators, spanning more than 30 academic institutions. Research funded by the OMP amounted to about $6.9M in FY 1994. This document is a collection of abstracts summarizing the component projects of Phase I of the OMP. This phase included both research and technology development, and comprised projects of both two and three years duration. The attached abstracts describe the goals, methods, measurement scales, strengths and limitations, and status of each project, and level of support. Keywords are provided to index the various projects. The names, addresses, affiliations, and major areas of expertise of the investigators are provided in appendices.

  11. Robotics Technology Development Program. Technology summary

    SciTech Connect

    Not Available

    1994-02-01

    The Robotics Technology Development Program (RTDP) is a ``needs-driven`` effort. A lengthy series of presentations and discussions at DOE sites considered critical to DOE`s Environmental Restoration and Waste Management (EM) Programs resulted in a clear understanding of needed robotics applications toward resolving definitive problems at the sites. A detailed analysis of the Tank Waste Retrieval (TWR), Contaminant Analysis Automation (CAA), Mixed Waste Operations (MWO), and Decontamination & Dismantlement (D&D). The RTDP Group realized that much of the technology development was common (Cross Cutting-CC) to each of these robotics application areas, for example, computer control and sensor interface protocols. Further, the OTD approach to the Research, Development, Demonstration, Testing, and Evaluation (RDDT&E) process urged an additional organizational break-out between short-term (1--3 years) and long-term (3--5 years) efforts (Advanced Technology-AT). The RDTP is thus organized around these application areas -- TWR, CAA, MWO, D&D and CC&AT -- with the first four developing short-term applied robotics. An RTDP Five-Year Plan was developed for organizing the Program to meet the needs in these application areas.

  12. Summary of NR Program Prometheus Efforts

    NASA Astrophysics Data System (ADS)

    Ashcroft, John; Eshelman, Curtis

    2007-01-01

    The Naval Reactors Program led work on the development of a reactor plant system for the Prometheus space reactor program. The work centered on a 200 kWe electric reactor plant with a 15-20 year mission applicable to nuclear electric propulsion (NEP). After a review of all reactor and energy conversion alternatives, a direct gas Brayton reactor plant was selected for further development. The work performed subsequent to this selection included preliminary nuclear reactor and reactor plant design, development of instrumentation and control techniques, modeling reactor plant operational features, development and testing of core and plant material options, and development of an overall project plan. Prior to restructuring of the program, substantial progress had been made on defining reference plant operating conditions, defining reactor mechanical, thermal and nuclear performance, understanding the capabilities and uncertainties provided by material alternatives, and planning non-nuclear and nuclear system testing. The mission requirements for the envisioned NEP missions cannot be accommodated with existing reactor technologies. Therefore concurrent design, development and testing would be needed to deliver a functional reactor system. Fuel and material performance beyond the current state of the art is needed. There is very little national infrastructure available for fast reactor nuclear testing and associated materials development and testing. Surface mission requirements may be different enough to warrant different reactor design approaches and development of a generic multi-purpose reactor requires substantial sacrifice in performance capability for each mission.

  13. Summary of NR Program Prometheus Efforts

    SciTech Connect

    J Ashcroft; C Eshelman

    2006-02-08

    The Naval Reactors Program led work on the development of a reactor plant system for the Prometheus space reactor program. The work centered on a 200 kWe electric reactor plant with a 15-20 year mission applicable to nuclear electric propulsion (NEP). After a review of all reactor and energy conversion alternatives, a direct gas Brayton reactor plant was selected for further development. The work performed subsequent to this selection included preliminary nuclear reactor and reactor plant design, development of instrumentation and control techniques, modeling reactor plant operational features, development and testing of core and plant material options, and development of an overall project plan. Prior to restructuring of the program, substantial progress had been made on defining reference plant operating conditions, defining reactor mechanical, thermal and nuclear performance, understanding the capabilities and uncertainties provided by material alternatives, and planning non-nuclear and nuclear system testing. The mission requirements for the envisioned NEP missions cannot be accommodated with existing reactor technologies. Therefore concurrent design, development and testing would be needed to deliver a functional reactor system. Fuel and material performance beyond the current state of the art is needed. There is very little national infrastructure available for fast reactor nuclear testing and associated materials development and testing. Surface mission requirements may be different enough to warrant different reactor design approaches and development of a generic multi-purpose reactor requires substantial sacrifice in performance capability for each mission.

  14. Summary of NR Program Prometheus Efforts

    SciTech Connect

    Ashcroft, John; Eshelman, Curtis

    2007-01-30

    The Naval Reactors Program led work on the development of a reactor plant system for the Prometheus space reactor program. The work centered on a 200 kWe electric reactor plant with a 15-20 year mission applicable to nuclear electric propulsion (NEP). After a review of all reactor and energy conversion alternatives, a direct gas Brayton reactor plant was selected for further development. The work performed subsequent to this selection included preliminary nuclear reactor and reactor plant design, development of instrumentation and control techniques, modeling reactor plant operational features, development and testing of core and plant material options, and development of an overall project plan. Prior to restructuring of the program, substantial progress had been made on defining reference plant operating conditions, defining reactor mechanical, thermal and nuclear performance, understanding the capabilities and uncertainties provided by material alternatives, and planning non-nuclear and nuclear system testing. The mission requirements for the envisioned NEP missions cannot be accommodated with existing reactor technologies. Therefore concurrent design, development and testing would be needed to deliver a functional reactor system. Fuel and material performance beyond the current state of the art is needed. There is very little national infrastructure available for fast reactor nuclear testing and associated materials development and testing. Surface mission requirements may be different enough to warrant different reactor design approaches and development of a generic multi-purpose reactor requires substantial sacrifice in performance capability for each mission.

  15. Advanced space program studies. Overall executive summary

    NASA Technical Reports Server (NTRS)

    Wolfe, M. G.

    1977-01-01

    NASA and DoD requirements and planning data were used in multidiscipline advanced planning investigations of space operations and associated elements (including man), identification of potential low cost approaches, vehicle design, cost synthesis techniques, technology forecasting and opportunities for DoD technology transfer, and the development near-, mid-, and far-term space initiatives and development plans with emphasis on domestic and military commonality. An overview of objectives and results are presented for the following studies: advanced space planning and conceptual analysis, shuttle users, technology assessment and new opportunities, standardization and program practice, integrated STS operations planning, solid spinning upper stage, and integrated planning support functions.

  16. Advanced space program studies: Overall executive summary

    NASA Technical Reports Server (NTRS)

    Sitney, L. R.

    1974-01-01

    Studies were conducted to provide NASA with advanced planning analyses which relate integrated space program goals and options to credible technical capabilities, applications potential, and funding resources. The studies concentrated on the following subjects: (1) upper stage options for the space transportation system based on payload considerations, (2) space servicing and standardization of payloads, (3) payload operations, and (4) space transportation system economic analyses related to user charges and new space applications. A systems cost/performance model was developed to synthesize automated, unmanned spacecraft configurations based on the system requirements and a list of equipments at the assembly level.

  17. Underground Energy Storage Program. 1984 annual summary

    SciTech Connect

    Kannberg, L.D.

    1985-06-01

    Underground Energy Storage (UES) Program activities during the period from April 1984 through March 1985 are briefly described. Primary activities in seasonal thermal energy storage (STES) involved field testing of high-temperature (>100/sup 0/C (212/sup 0/F)) aquifer thermal energy storage (ATES) at St. Paul, laboratory studies of geochemical issues associated with high-temperatures ATES, monitoring of chill ATES facilities in Tuscaloosa, and STES linked with solar energy collection. The scope of international activities in STES is briefly discussed.

  18. Program summary for the Civilian Reactor Development Program

    SciTech Connect

    1982-07-01

    This Civilian Reactor Development Program document has the prime purpose of summarizing the technical programs supported by the FY 1983 budget request. This section provides a statement of the overall program objectives and a general program overview. Section II presents the technical programs in a format intended to show logical technical interrelationships, and does not necessarily follow the structure of the formal budget presentation. Section III presents the technical organization and management structure of the program.

  19. Refan program. Phase 1: Summary report

    NASA Technical Reports Server (NTRS)

    Sams, E. W.; Bresnahan, D. L.

    1973-01-01

    The Refan Program is aimed at a large reduction in aircraft approach and takeoff noise in the vicinity of airports caused by the JT3D-powered 707's and DC-8's and the JT8D-powered 727's, 737's and DC-9's. These aircraft represent a major part of the existing commercial fleet. The noise reductions can be achieved by engine and nacelle modifications in the form of aircraft retrofit kits. Engine turbomachinery noise is reduced by replacing the current two-stage fan with a larger single-stage fan and by nacelle acoustic treatment. Jet noise is reduced by the reduction on jet velocity caused by additional turbine work extraction to drive the larger bypass fan. The predicted net effect of these modifications on installed performance is large noise reductions on both approach and takeoff, increased takeoff thrust, decreased takeoff field length, and maintained or improved aircraft range depending on the amount of acoustic treatment included. The Refan Program is being conducted in two phases under contracts with one engine and two airframe companies. Results of the Phase I work are summarized in this report which describes the refan nacelle configurations studied, the airplane modifications required to install the nacelles, and the resulting airplane performance and noise reductions predicted for all five aircraft.

  20. Geothermal direct heat applications program summary

    SciTech Connect

    1980-04-01

    The use of geothermal energy for direct heat purposes by the private sector within the US has been quite limited to date. However, there is a large potential market for thermal energy in such areas as industrial processing, agribusiness, and space/water heating of commercial and residential buildings. Technical and economic information is needed to assist in identifying prospective direct heat users and to match their energy needs to specific geothermal reservoirs. Technological uncertainties and associated economic risks can influence the user's perception of profitability to the point of limiting private investment in geothermal direct applications. To stimulate development in the direct heat area, the Department of Energy, Division of Geothermal Energy, issued two Program Opportunity Notices (PON's). These solicitations are part of DOE's national geothermal energy program plan, which has as its goal the near-term commercialization by the private sector of hydrothermal resources. Encouragement is being given to the private sector by DOE cost-sharing a portion of the front-end financial risk in a limited number of demonstration projects. The twenty-two projects summarized herein are direct results of the PON solicitations.

  1. Data Summary: Articulation between Secondary and Postsecondary Occupational Education Programs.

    ERIC Educational Resources Information Center

    State Univ. of New York, Albany. Two Year Coll. Development Center.

    In 1984-85, a research project was conducted in New York State to develop a summary of existing formal agreements in occupational programs between secondary and postsecondary institutions, and to determine characteristics important to the success of existing agreements. Survey responses were obtained from 45 two-year colleges and 37 secondary…

  2. Girls Programming in New York City. A Summary Report.

    ERIC Educational Resources Information Center

    Academy for Educational Development, Inc., New York, NY.

    This summary report describes the findings of a study undertaken in 1995 by the Academy for Educational Development, a nonprofit educational evaluation and research organization for the New York Women's Foundation. The major purposes of the study were to document the status of girls aged 9 to 15 in New York City, identify exemplary programs for…

  3. DUAL ALKALI TEST AND EVALUATION PROGRAM. VOLUME I. EXECUTIVE SUMMARY

    EPA Science Inventory

    Volume I of the report is an executive summary of the results of a three-task program to investigate, characterize, and evaluate the basic process chemistry and the various operating modes of sodium-based dual alkali scrubbing processes. The tasks were: I, laboratory studies at b...

  4. FWP executive summaries: Basic energy sciences materials sciences programs

    SciTech Connect

    Samara, G.A.

    1996-02-01

    This report provides an Executive Summary of the various elements of the Materials Sciences Program which is funded by the Division of Materials Sciences, Office of Basic Energy Sciences, U.S. Department of Energy at Sandia National Laboratories, New Mexico.

  5. DOE passive solar commercial buildings program: project summaries

    SciTech Connect

    Not Available

    1982-01-01

    The 23 projects participating in this program comprise a wide range of building types including offices, retail establishments, educational facilities, public service facilities, community and visitor centers, and private specialized-use facilities, located throughout the United States. Summary data and drawings are presented for each project. (MHR)

  6. Hawaii Ocean Mixing Experiment: Program Summary

    NASA Technical Reports Server (NTRS)

    Ray, Richard D.; Chao, Benjamin F. (Technical Monitor)

    2002-01-01

    It is becoming apparent that insufficient mixing occurs in the pelagic ocean to maintain the large scale thermohaline circulation. Observed mixing rates fall a factor of ten short of classical indices such as Munk's "Abyssal Recipe." The growing suspicion is that most of the mixing in the sea occurs near topography. Exciting recent observations by Polzin et al., among others, fuel this speculation. If topographic mixing is indeed important, it must be acknowledged that its geographic distribution, both laterally and vertically, is presently unknown. The vertical distribution of mixing plays a critical role in the Stommel Arons model of the ocean interior circulation. In recent numerical studies, Samelson demonstrates the extreme sensitivity of flow in the abyssal ocean to the spatial distribution of mixing. We propose to study the topographic mixing problem through an integrated program of modeling and observation. We focus on tidally forced mixing as the global energetics of this process have received (and are receiving) considerable study. Also, the well defined frequency of the forcing and the unique geometry of tidal scattering serve to focus the experiment design. The Hawaiian Ridge is selected as a study site. Strong interaction between the barotropic tide and the Ridge is known to take place. The goals of the Hawaiian Ocean Mixing Experiment (HOME) are to quantify the rate of tidal energy loss to mixing at the Ridge and to identify the mechanisms by which energy is lost and mixing generated. We are challenged to develop a sufficiently comprehensive picture that results can be generalized from Hawaii to the global ocean. To achieve these goals, investigators from five institutions have designed HOME, a program of historic data analysis, modeling and field observation. The Analysis and Modeling efforts support the design of the field experiments. As the program progresses, a global model of the barotropic (depth independent) tide, and two models of the

  7. Energy-efficient buildings program evaluations. Volume 2: Evaluation summaries

    SciTech Connect

    Lee, A.D.; Mayi, D.; Edgemon, S.D.

    1997-04-01

    This document presents summaries of code and utility building program evaluations reviewed as the basis for the information presented in Energy-Efficient Buildings Program Evaluations, Volume 1: Findings and Recommendations, DOE/EE/OBT-11569, Vol. 1. The main purpose of this volume is to summarize information from prior evaluations of similar programs that may be useful background for designing and conducting an evaluation of the BSGP. Another purpose is to summarize an extensive set of relevant evaluations and provide a resource for program designers, mangers, and evaluators.

  8. 3D Elevation Program: summary for Vermont

    USGS Publications Warehouse

    Carswell, William J., Jr.

    2015-01-01

    The National Enhanced Elevation Assessment evaluated multiple elevation data acquisition options to determine the optimal data quality and data replacement cycle relative to cost to meet the identified requirements of the user community. The evaluation demonstrated that lidar acquisition at quality level 2 for the conterminous United States and quality level 5 interferometric synthetic aperture radar (ifsar) data for Alaska with a 6- to 10-year acquisition cycle provided the highest benefit/cost ratios. The 3D Elevation Program (3DEP) initiative selected an 8-year acquisition cycle for the respective quality levels. 3DEP, managed by the U.S. Geological Survey, the Office of Management and Budget Circular A–16 lead agency for terrestrial elevation data, responds to the growing need for high-quality topographic data and a wide range of other 3D representations of the Nation’s natural and constructed features.

  9. 3D Elevation Program: summary for Nebraska

    USGS Publications Warehouse

    Carswell, William J., Jr.

    2015-01-01

    The National Enhanced Elevation Assessment evaluated multiple elevation data acquisition options to determine the optimal data quality and data replacement cycle relative to cost to meet the identified requirements of the user community. The evaluation demonstrated that lidar acquisition at quality level 2 for the conterminous United States and quality level 5 interferometric synthetic aperture radar (ifsar) data for Alaska with a 6- to 10-year acquisition cycle provided the highest benefit/cost ratios. The 3D Elevation Program (3DEP) initiative selected an 8-year acquisition cycle for the respective quality levels. 3DEP, managed by the U.S. Geological Survey, the Office of Management and Budget Circular A–16 lead agency for terrestrial elevation data, responds to the growing need for high-quality topographic data and a wide range of other 3D representations of the Nation’s natural and constructed features.

  10. In Situ Remediation Integrated Program: Technology summary

    SciTech Connect

    Not Available

    1994-02-01

    The In Situ Remediation Integrated Program (ISR IP) was instituted out of recognition that in situ remediation could fulfill three important criteria: significant cost reduction of cleanup by eliminating or minimizing excavation, transportation, and disposal of wastes; reduced health impacts on workers and the public by minimizing exposure to wastes during excavation and processing; and remediation of inaccessible sites, including: deep subsurfaces, in, under, and around buildings. Buried waste, contaminated soils and groundwater, and containerized wastes are all candidates for in situ remediation. Contaminants include radioactive wastes, volatile and non-volatile organics, heavy metals, nitrates, and explosive materials. The ISR IP intends to facilitate development of in situ remediation technologies for hazardous, radioactive, and mixed wastes in soils, groundwater, and storage tanks. Near-term focus is on containment of the wastes, with treatment receiving greater effort in future years. ISR IP is an applied research and development program broadly addressing known DOE environmental restoration needs. Analysis of a sample of 334 representative sites by the Office of Environmental Restoration has shown how many sites are amenable to in situ remediation: containment--243 sites; manipulation--244 sites; bioremediation--154 sites; and physical/chemical methods--236 sites. This needs assessment is focused on near-term restoration problems (FY93--FY99). Many other remediations will be required in the next century. The major focus of the ISR EP is on the long term development of permanent solutions to these problems. Current needs for interim actions to protect human health and the environment are also being addressed.

  11. Rocky Flats Compliance Program; Technology summary

    SciTech Connect

    1994-02-01

    The Department of Energy (DOE) established the Office of Technology Development (EM-50) (OTD) as an element of Environmental Restoration and Waste Management (EM) in November 1989. The primary objective of the Office of Technology Development, Rocky Flats Compliance Program (RFCP), is to develop altemative treatment technologies for mixed low-level waste (wastes containing both hazardous and radioactive components) to use in bringing the Rocky Flats Plant (RFP) into compliance with Federal and state regulations and agreements. Approximately 48,000 cubic feet of untreated low-level mixed waste, for which treatment has not been specified, are stored at the RFP. The cleanup of the Rocky Flats site is driven by agreements between DOE, the Environmental Protection Agency (EPA), and the Colorado Department of Health (CDH). Under these agreements, a Comprehensive Treatment and Management Plan (CTMP) was drafted to outline the mechanisms by which RFP will achieve compliance with the regulations and agreements. This document describes DOE`s strategy to treat low-level mixed waste to meet Land Disposal Restrictions and sets specific milestones related to the regulatory aspects of technology development. These milestones detail schedules for the development of technologies to treat all of the mixed wastes at the RFP. Under the Federal Facilities Compliance Act (FFCA), the CTMP has been incorporated into Rocky Flats Plant Conceptual Site Treatment Plan (CSTP). The CSTP will become the Rocky Flats Plant site Treatment Plan in 1995 and will supersede the CTMP.

  12. MIxed Waste Integrated Program (MWIP): Technology summary

    SciTech Connect

    1994-02-01

    The mission of the Mixed Waste Integrated Program (MWIP) is to develop and demonstrate innovative and emerging technologies for the treatment and management of DOE`s mixed low-level wastes (MLLW) for use by its customers, the Office of Waste Operations (EM-30) and the Office of Environmental Restoration (EM-40). The primary goal of MWIP is to develop and demonstrate the treatment and disposal of actual mixed waste (MMLW and MTRU). The vitrification process and the plasma hearth process are scheduled for demonstration on actual radioactive waste in FY95 and FY96, respectively. This will be accomplished by sequential studies of lab-scale non-radioactive testing followed by bench-scale radioactive testing, followed by field-scale radioactive testing. Both processes create a highly durable final waste form that passes leachability requirements while destroying organics. Material handling technology, and off-gas requirements and capabilities for the plasma hearth process and the vitrification process will be established in parallel.

  13. SUMMARY OF 2009 RHEOLOGY MODIFIER PROGRAM

    SciTech Connect

    Hansen, E.

    2009-12-08

    The overall objective of the EM-31 Rheological Modifiers and Wetting Agents program is to utilize commercially available rheology modifiers to increase the solids fraction of radioactive sludge based waste streams, resulting in an increase in throughput and decreasing the overall processing time. The program first investigates the impact of rheology modifiers on slurry simulants and then utilizes the most effective rheology modifiers on radioactive slurries. The work presented in this document covers the initial investigation of rheology modifier testing with simulants. This task is supported by both the Savannah River National Laboratory (SRNL) and Pacific Northwest National Laboratory (PNNL). The SRNL EM-31 task, for this year, was to investigate the use of rheology modifiers on simulant Defense Waste Processing Facility (DWPF) melter feeds. The task is to determine, based on the impact of the rheology modifier, if there are rheology modifiers that could reduce the water content of the slurry going to the DWPF melter, hence increasing the melt rate by decreasing the water loading. The rheology modifier in essence would allow a higher solids content slurry to have the same type of rheology or pumpability of a lower solids slurry. The modifiers selected in this report were determined based on previous modifiers used in high level waste melter feed simulants, on-going testing performed by counterparts at PNNL, and experiences gain through use of modifiers in other Department of Energy (DOE) processes such as grout processing. There were 12 rheology modifiers selected for testing, covering both organic and inorganic types and they were tested at four different concentrations for a given melter feed. Five different DWPF melter feeds were available and there was adequate material in one of the melter feeds to increase the solids concentration, resulting in a total of six simulants for testing. The mass of melter feed available in each simulant was not adequate for

  14. Hollow clay tile wall program summary report

    SciTech Connect

    Henderson, R.C.; Jones, W.D.

    1995-07-30

    Many of the Y-12 Plant buildings, constructed during the 1940s and 1950s, consist of steel ed concrete framing infilled with hollow clay tile (HCT). The infill was intended to provide for building enclosure and was not designed to have vertical or lateral load-carrying capacity. During the late 1970s and early 1980s, seismic and wind evaluations were performed on many of these buildings in conjunction with the preparation of a site-wide safety analysis report. This analytical work, based on the best available methodology, considered lateral load-carrying capacity of the HCT infill on the basis of building code allowable shear values. In parallel with the analysis effort, DOE initiated a program to develop natural phenomena capacity and performance criteria for existing buildings, but these criteria did not specify guidelines for determining the lateral force capacity of frames infilled with HCT. The evaluation of infills was, therefore, based on the provisions for the design of unreinforced masonry as outlined in standard masonry codes. When the results of the seismic and wind evaluations were compared with the new criteria, the projected building capacities fell short of the requirements. Apparently, if the buildings were to meet the new criteria, many millions of dollars would be required for building upgrades. Because the upgrade costs were significant, the assumptions and approaches used in the analyses were reevaluated. Four issues were identified: (1) Once the infilled walls cracked, what capacity (nonlinear response), if any, would the walls have to resist earthquake or wind loads applied in the plane of the infill (in-plane)? (2) Would the infilled walls remain within the steel or reinforced concrete framing when subjected to earthquake or high wind loads applied perpendicular to the infill (out-of-plane)? (3) What was the actual shear capacity of the HCT infill? (4) Was modeling the HCT infill as a shear wall the best approach?

  15. Federal Transit Administration 1998 statistical summaries: Grant assistance programs

    SciTech Connect

    Grubb, N.

    1999-03-08

    The 1998 Statistical Summaries provides information about the Federal Transit Administration's (FTA) major financial aid programs for Federal Fiscal Year (FY) 1998. The report covers the following programs: Urbanized Area Formula, Non-urbanized Area Formula, Rural Transit Assistance Program, Elderly and Persons with Disabilities, Capital, Interstate Substitution, Metropolitan Planning, State Planning and Research, Consolidated Planning Grants, and State Infrastructure Banks. The data used in this report are compiled from the capital, operating, and planning assistance grants to transit authorities, states, planning agencies, and other units of local government. The Statistical Summaries report is organized into three main sections. The first section includes appropriations and budget authorities. This is followed by detailed obligation data for the current fiscal year. The final section includes summarized historical data.

  16. Manned Space Programs Accident/Incident Summaries (1970 - 1971)

    NASA Technical Reports Server (NTRS)

    1972-01-01

    A compilation of 223 mishaps assembled from company and NASA records covering the Accident/Incident experience in 1970-1971 in the Manned Space Flight Programs is presented. It is the companion volume to NASA-CR-120998 which covered the years 1963-1969. The objectives of this summary is to make available to Government agencies and industrial firms the lessons learned from these mishaps. Each accident/incident summary has been reviewed by description, cause and recommended preventive action. The summaries have been categorized by the following ten systems: (1) Cryogenic; (2) Electrical; (3) Facility/GSE; (4) Fuel and Propellant; (5) Life Support; (6) Ordnance; (7) Pressure; (8) Propulsion; (9) Structural; and (10) Transport/Handling.

  17. Satellite Power System (SPS) FY 79 program summary

    NASA Technical Reports Server (NTRS)

    1980-01-01

    The Satellite Power System (SPS) program a joint effort to develop an initial understanding of the technical feasibility, the economic practicality, and the social and environmental acceptability of the SPS concept is discussed. This is being accomplished through implementation of the Concept Development and Evaluation Program Plan which is scheduled for completion by the end of FY 1980. This Program Summary not only covers FY 1979 but includes work completed in FY 1977 and FY 1978 in order to give a comprehensive picture of the DOE involvement in the SPS concept development and evaluation process.

  18. Space Technology Mission Directorate Game Changing Development Program FY2015 Annual Program Review: Advanced Manufacturing Technology

    NASA Technical Reports Server (NTRS)

    Vickers, John; Fikes, John

    2015-01-01

    The Advance Manufacturing Technology (AMT) Project supports multiple activities within the Administration's National Manufacturing Initiative. A key component of the Initiative is the Advanced Manufacturing National Program Office (AMNPO), which includes participation from all federal agencies involved in U.S. manufacturing. In support of the AMNPO the AMT Project supports building and Growing the National Network for Manufacturing Innovation through a public-private partnership designed to help the industrial community accelerate manufacturing innovation. Integration with other projects/programs and partnerships: STMD (Space Technology Mission Directorate), HEOMD, other Centers; Industry, Academia; OGA's (e.g., DOD, DOE, DOC, USDA, NASA, NSF); Office of Science and Technology Policy, NIST Advanced Manufacturing Program Office; Generate insight within NASA and cross-agency for technology development priorities and investments. Technology Infusion Plan: PC; Potential customer infusion (TDM, HEOMD, SMD, OGA, Industry); Leverage; Collaborate with other Agencies, Industry and Academia; NASA roadmap. Initiatives include: Advanced Near Net Shape Technology Integrally Stiffened Cylinder Process Development (launch vehicles, sounding rockets); Materials Genome; Low Cost Upper Stage-Class Propulsion; Additive Construction with Mobile Emplacement (ACME); National Center for Advanced Manufacturing.

  19. Peer Assistance and Leadership (PAL) Program. Program Summary.

    ERIC Educational Resources Information Center

    Thomas, H. Grant, Jr.

    This document describes the Peer Assistance and Leadership (PAL) Program, a peer helping program developed by the Austin Independent School District in Austin, Texas. It explains how selected high school students are trained to work as peer facilitators with younger students either on their own campus or from feeder junior high or elementary…

  20. Biomass Program 2007 Program Peer Review - Thermochemical Conversion Platform Summary

    SciTech Connect

    none,

    2009-10-27

    This document discloses the comments provided by a review panel at the U.S. Department of Energy Office of the Biomass Program Peer Review held on November 15-16, 2007 in Baltimore, MD and the Biomass Program Peer Review for the Thermochemical Platform, held on July 9th and 10th in Golden, Colorado.

  1. Satellite Power System (SPS) FY 79 Program Summary

    SciTech Connect

    Not Available

    1980-01-01

    The Satellite Power System (SPS) program is a joint effort of the US Department of Energy (DOE) and the National Aeronautics and Space Administration (NASA). It is managed by the SPS Project Office within DOE's Office of Energy Research. SPS project organization is shown in Figure 1. The SPS Project Office was established in 1978 and is responsible for the planning, management and integration of SPS research in four areas: systems definition, environmental assessment, societal assessment, and comparative assessment. In fulfilling its responsibilities, the SPS Project Office directs research and assessment efforts to determine the feasibility of the SPS concept, funds organizations supporting the program, and disseminates information developed from project research and assessments. The objective of the SPS program is to develop an initial understanding of the technical feasibility, the economic practicality, and the social and environmental acceptability of the SPS concept. This is being accomplished through implementation of the Concept Development and Evaluation Program Plan which is scheduled for completion by the end of FY 1980. The SPS Project Office annually issues a Program Summary which describes the research undertaken during the preceding fiscal year. This Program Summary covers FY 1979. It includes work completed in FY 1977 and FY 1978 in order to give a comprehensive picture of the DOE involvement in the SPS concept development and evaluation process.

  2. Advanced Thermionic Technology Program: summary report. Volume 1. Final report

    SciTech Connect

    Not Available

    1984-10-01

    This report summarizes the progress made by the Advanced Thermionic Technology Program during the past several years. This program, sponsored by the US Department of Energy, has had as its goal adapting thermionic devices to generate electricity in a terrestrial (i.e., combustion) environment. The technology has previously been developed for astronautical applications. The report is organized in four volumes, each focused as much as possible on the needs of a particular audience. Volume 1 contains Part A, the Executive Summary. This Executive Summary describes the accomplishments of the Program in brief, but assumes the reader's familiarity with the thermionic process and the technical issues associated with the Program. For this reason, Volume 1 also contains Part B, a minimally technical overview of the Advanced Thermionic Technology Program. Volume 2 (Part C) concentrates on the progress made in developing and fabricating the ''current generation'' of chemical vapor deposited hot shell thermionic converters and is addressed to those primarily concerned with today's capabilities in terrestrial thermionic technology. Volume 3 (Part D) contains the results of systems studies of primary interest to those involved in identifying and evaluating applications for thermionics. Volume 4 (Part E) is a highly technical discussion of the attempts made by the program to push the state-of-the-art beyond the current generation of converters and is directed toward potential researchers engaged in this same task. These technical discussions are complemented with Appendices where appropriate.

  3. Second NBL measurement evaluation program meeting: A summary

    SciTech Connect

    Spaletto, M.I.; Clapper, M.; Tolbert, M.E.M.

    1997-12-31

    New Brunswick Laboratory (NBL), the US government`s nuclear materials measurements and reference materials laboratory, administers interlaboratory measurement evaluation programs to evaluate the quality and adequacy of safeguards measurements. The NBL Measurement Evaluation Program covers several types of safeguards analytical measurements. The Safeguards Measurement Evaluation (SME) program distributes test materials destructive measurements of uranium for both elemental concentration and isotopic abundances, and of plutonium for isotopic abundances. The Calorimetry Exchange (CalEx) Program tests the quality of nondestructive measurements of plutonium isotopic abundances by gamma spectroscopy and plutonium concentration by calorimetry. In May 1997, more than 30 representatives from the Department of Energy (DOE), its contractor laboratories, and Nuclear Regulatory Commission licensees met at NBL in Argonne, Illinois, for the annual meeting of the Measurement Evaluation Program. The summary which follows details key points that were discussed or presented at the meeting.

  4. Summary of commercial conservation programs environmental issues and program consistency

    SciTech Connect

    Beachler, M.C.

    1989-06-01

    Pacific Northwest Laboratory (PNL) conducted this study for the Office of Energy Resources of the Bonneville Power Administration. The purpose of the report is to compare and contrast the environmental requirements and issues involving Bonneville's residential conservation programs. In addition to environmental issues that Bonneville has addressed in environmental documents, this report also briefly examines new issues that may affect residential conservation programs. The key environmental concern confronting each of the programs with measures aimed at reducing air leakage in houses (both new and existing) is indoor air quality. There are inconsistencies in how the Weatherization Program and the New Homes programs approach indoor air quality. However, these differences make sense, given the character and constraints affecting how each program operates. Newer issues that have arisen include global warming, potential health effects of mineral and glass fibers, and possible fire hazards associated with plastic foam and cellulose insulation. Bonneville staff are aware of these issues as they relate to conservation programs. No action appears necessary at this time.

  5. Geothermal energy program summary: Volume 2, Research summaries, fiscal year 1988

    SciTech Connect

    Not Available

    1989-03-01

    The Geothermal Technology Division (GTD) of the US Department of Energy (DOE) is charged with the lead federal role in the research and development (R&D) of technologies that will assist industry in economically exploiting the nation`s vast geothermal resources. The GTD R&D program represents a comprehensive, balanced approach to establishing all forms of geothermal energy as significant contributors to the nation`s energy supply. It is structured both to maintain momentum in the growth of the existing hydrothermal industry and to develop long-term options offering the greatest promise for practical applications. The Geothermal Energy Program Summary for Fiscal Year 1988 is a two-volume set designed to be an easily accessible reference to inform the US geothermal industry and other interested parties of the technological advances and progress achieved in the DOE geothermal program as well as to describe the thrust of the current R&D effort and future R&D directions. This volume, Volume II, contains a detailed compilation of each GTD-funded R&D activity performed by national laboratories or under contract to industrial, academic, and nonprofit research institutions. The Program Summary is intended as an important technology transfer vehicle to assure the wide and timely dissemination of information concerning the department`s geothermal research.

  6. Biomass Program 2007 Program Peer Review - Feedstock Platform Summary

    SciTech Connect

    none,

    2009-10-27

    This document discloses the comments provided by a review panel at the U.S. Department of Energy Office of the Biomass Program Peer Review held on November 15-16, 2007 in Baltimore, MD and the Feedstock Platform Portfolio Peer Review held on August 21st through 23rd in Washington D.C.

  7. The 3D Elevation Program: summary of program direction

    USGS Publications Warehouse

    Snyder, Gregory I.

    2012-01-01

    The 3D Elevation Program (3DEP) initiative responds to a growing need for high-quality topographic data and a wide range of other three-dimensional representations of the Nation's natural and constructed features. The National Enhanced Elevation Assessment (NEEA), which was completed in 2011, clearly documented this need within government and industry sectors. The results of the NEEA indicated that enhanced elevation data have the potential to generate $13 billion in new benefits annually. The benefits apply to food risk management, agriculture, water supply, homeland security, renewable energy, aviation safety, and other areas. The 3DEP initiative was recommended by the National Digital Elevation Program and its 12 Federal member agencies and was endorsed by the National States Geographic Information Council (NSGIC) and the National Geospatial Advisory Committee (NGAC).

  8. A new mathematical programming model for scheduling flexible manufacturing systems

    SciTech Connect

    MacCarthy, B.; Liu, J.

    1994-12-31

    Flexibility is now a major consideration in the design of many manufacturing systems. Flexible manufacturing systems (FMS) have been developed in the last two decades. The principal elements of an FMS are (1) computer controlled machine tools, (2) a transport system and (3) a host computer system. Such systems may combine high flexibility with high productivity and may allow unsupervised production. However, in order to achieve these benefits, the control system must be capable of exercising intelligent supervisory management. Scheduling is at the heart of the control system and is still a major problem area. This paper describes a new mathematical programming model for a wide class of FMS scheduling problems based on a new classification scheme. A global optimization approach is adopted based on a mixed-integer linear programming model. Many important aspects of operational FMS, omitted form earlier models, are included. Key elements of model structure are highlighted. Computational experience with a comprehensive set of designed experiments is described. The applications of the model are noted and the development of effective heuristic procedures based on the model is highlighted.

  9. 77 FR 26509 - Request for Information on Proposed New Program: National Network for Manufacturing Innovation...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-05-04

    ..., materials, and equipment for additive manufacturing to enable low- cost, low-volume production using digital... Network for Manufacturing Innovation (NNMI) AGENCY: National Institute of Standards and Technology (NIST), Department of Commerce. ACTION: Request for information. SUMMARY: The NIST-hosted Advanced...

  10. In Situ Remediation Integrated Program: FY 1994 program summary

    SciTech Connect

    1995-04-01

    The US Department of Energy (DOE) established the Office of Technology Development (EM-50) as an element of the Office of Environmental Management (EM) in November 1989. In an effort to focus resources and address priority needs, EM-50 introduced the concept of integrated programs (IPs) and integrated demonstrations (IDs). The In Situ Remediation Integrated Program (ISR IP) focuses research and development on the in-place treatment of contaminated environmental media, such as soil and groundwater, and the containment of contaminants to prevent the contaminants from spreading through the environment. Using in situ remediation technologies to clean up DOE sites minimizes adverse health effects on workers and the public by reducing contact exposure. The technologies also reduce cleanup costs by orders of magnitude. This report summarizes project work conducted in FY 1994 under the ISR IP in three major areas: treatment (bioremediation), treatment (physical/chemical), and containment technologies. Buried waste, contaminated soils and groundwater, and containerized waste are all candidates for in situ remediation. Contaminants include radioactive waste, volatile and nonvolatile organics, heavy metals, nitrates, and explosive materials.

  11. Exploratory Technology Research Program for electrochemical energy storage. Executive summary report for 1991

    SciTech Connect

    Kinoshita, K.

    1992-06-01

    The US DOE Office of Propulsion Systems provides support for an electrochemical energy storage program, that includes research and development (R&D) on advanced rechargeable batteries and fuel cells. A major goal of this program is to develop electrochemical power sources suitable for application in electric vehicles. The program centers on advanced systems that offer the potential for high performance and low life-cycle costs. The DOE Electrochemical Energy Storage Program is divided into two projects: the Electric Vehicle Advanced Battery Systems Development (EVABS) Program and the Exploratory Technology Research (EM) Program. The EVABS Program management responsibility has been assigned to Sandia National Laboratory, and the Lawrence Berkeley Laboratory is responsible for management of the ETR Program. The EVABS and ETR Programs include an integrated matrix of R&D efforts designed to advance progress on several candidate electrochemical systems. The United States Advanced Battery Consortium (USABC), a tripartite undertaking between DOE, the US automobile manufacturers and the Electric Power Research Institute (EPRI), was formed in 1991 to accelerate the development of advanced batteries for consumer EVs. The role of the ETR Program is to perform supporting research on the advanced battery systems under development by the USABC and EVABS Program, and to evaluate new systems with potentially superior performance, durability and/or cost characteristics. The specific goal of the ETR Program is to identify the most promising electrochemical technologies and transfer them to the USABC, the battery industry and/or the EVABS Program for further development and scaleup. This executive summary summarizes the research, financial and management activities relevant to the ETR Program in CY 1991.

  12. 10 CFR 611.202 - Advanced Technology Vehicle Manufacturing Facility Award Program.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... Manufacturing Facility Award Program, 10 CFR part 611, subpart C, awards for eligible projects. ... 10 Energy 4 2010-01-01 2010-01-01 false Advanced Technology Vehicle Manufacturing Facility Award... TECHNOLOGY VEHICLES MANUFACTURER ASSISTANCE PROGRAM Facility/Funding Awards § 611.202 Advanced...

  13. 24 CFR 3288.215 - Effect on other manufactured home program requirements.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Effect on other manufactured home... COMMISSIONER, DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT MANUFACTURED HOME DISPUTE RESOLUTION PROGRAM State Dispute Resolution Programs in Non-HUD Administered States § 3288.215 Effect on other manufactured...

  14. 24 CFR 3288.215 - Effect on other manufactured home program requirements.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 24 Housing and Urban Development 5 2011-04-01 2011-04-01 false Effect on other manufactured home... COMMISSIONER, DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT MANUFACTURED HOME DISPUTE RESOLUTION PROGRAM State Dispute Resolution Programs in Non-HUD Administered States § 3288.215 Effect on other manufactured...

  15. 24 CFR 3288.215 - Effect on other manufactured home program requirements.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 24 Housing and Urban Development 5 2013-04-01 2013-04-01 false Effect on other manufactured home... COMMISSIONER, DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT MANUFACTURED HOME DISPUTE RESOLUTION PROGRAM State Dispute Resolution Programs in Non-HUD Administered States § 3288.215 Effect on other manufactured...

  16. 10 CFR 611.202 - Advanced Technology Vehicle Manufacturing Facility Award Program.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... Vehicle Manufacturing Facility Award Program. DOE may issue, under the Advanced Technology Vehicle Manufacturing Facility Award Program, 10 CFR part 611, subpart C, awards for eligible projects. ... 10 Energy 4 2014-01-01 2014-01-01 false Advanced Technology Vehicle Manufacturing Facility...

  17. 10 CFR 611.202 - Advanced Technology Vehicle Manufacturing Facility Award Program.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... Vehicle Manufacturing Facility Award Program. DOE may issue, under the Advanced Technology Vehicle Manufacturing Facility Award Program, 10 CFR part 611, subpart C, awards for eligible projects. ... 10 Energy 4 2011-01-01 2011-01-01 false Advanced Technology Vehicle Manufacturing Facility...

  18. 10 CFR 611.202 - Advanced Technology Vehicle Manufacturing Facility Award Program.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... Vehicle Manufacturing Facility Award Program. DOE may issue, under the Advanced Technology Vehicle Manufacturing Facility Award Program, 10 CFR part 611, subpart C, awards for eligible projects. ... 10 Energy 4 2013-01-01 2013-01-01 false Advanced Technology Vehicle Manufacturing Facility...

  19. 10 CFR 611.202 - Advanced Technology Vehicle Manufacturing Facility Award Program.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... Vehicle Manufacturing Facility Award Program. DOE may issue, under the Advanced Technology Vehicle Manufacturing Facility Award Program, 10 CFR part 611, subpart C, awards for eligible projects. ... 10 Energy 4 2012-01-01 2012-01-01 false Advanced Technology Vehicle Manufacturing Facility...

  20. U.S. Department of Energy Photovoltaic Energy Program Contract Summary: Fiscal Year 2000

    SciTech Connect

    Surek, T.

    2001-02-21

    This report summarizes the in-house and subcontracted research and development (R and D) activities under the National Center for Photovoltaics (NCPV) and U.S. Department of Energy (DOE) National Photovoltaics Program from October 1, 1999, through September 30, 2000 (FY 2000). The mission of the DOE National Photovoltaics Program is to make PV a significant part of the domestic economy-as an industry and an energy resource. The two primary goals of the national program are to (1) maintain the U.S. industry's world leadership in research and technology development and (2) help the U.S. industry remain a major, profitable force in the world market. The NCPV is part of the National PV Program and provides leadership and support to the national program toward achieving its mission and goals. This Contract Summary for fiscal year (FY) 2000 documents some 179 research projects supported by the PV Program, performed by 107 organizations in 32 states, including 69 projects performed by universities and 60 projects performed by our industry partners. Of the total FY 2000 PV Program budget of $65.9 million, the industry and university research efforts received $36.9 million, or nearly 56%. And, of this amount, more than 93% was for contractors selected on a competitive basis. Much of the funding to industry was matched by industry cost-sharing. Each individual effort described in this summary represents another step toward improving PV manufacturing, performance, cost, and applications, and another step toward accomplishing the DOE PV Program's overall mission.

  1. An Evaluation of the Manufacturing Technology Partnership (MTP) Program. Technical Report No. 96-007.

    ERIC Educational Resources Information Center

    Hollenbeck, Kevin

    The Manufacturing Technology Program (MTP) is a partnership between General Motors, the United Auto Workers, and the public schools in Flint, Michigan, that originated as a preapprenticeship program and has since expanded into a program preparing youth for manufacturing. The programs' effectiveness was examined through a comparison group-based…

  2. Telescience testbed pilot program, volume 1: Executive summary

    NASA Technical Reports Server (NTRS)

    Leiner, Barry M.

    1989-01-01

    Space Station Freedom and its associated labs, coupled with the availability of new computing and communications technologies, have the potential for significantly enhancing scientific research. A Telescience Testbed Pilot Program (TTPP), aimed at developing the experience base to deal with issues in the design of the future information system of the Space Station era. The testbeds represented four scientific disciplines (astronomy and astrophysics, earth sciences, life sciences, and microgravity sciences) and studied issues in payload design, operation, and data analysis. This volume, of a 3 volume set, which all contain the results of the TTPP, is the executive summary.

  3. A mathematical programming model for reconfiguration of flexible manufacturing cells

    NASA Astrophysics Data System (ADS)

    Yılmaz, Ebru; Erol, Rızvan

    2015-02-01

    In flexible manufacturing cells, changes in demand size, product mix, part variety, existing routings and set-up/operation times may require reconfiguration of the cells. In this study, an approach is developed to decide when and how such a reconfiguration should be carried out for existing cells. This study considers reconfiguration in terms of changing part routings, adding a new machine type in a cell, duplicating an existing machine type, removing an existing machine from a cell and transferring a machine to another cell. The study also shows the total number of tools of each type on each machine located in each cell after reconfiguration. To make the optimal reconfiguration decisions, a mathematical programming model to minimize the total reconfiguration cost is developed. The developed model considers the lower and upper bounds on machine utilizations and the time limits on machine cycle times to decide when to reconfigure the system.

  4. Constellation Program: Lessons Learned. Volume 1; Executive Summary

    NASA Technical Reports Server (NTRS)

    Rhatigan, Jennifer L. (Editor)

    2011-01-01

    This document (Volume I) provides an executive summary of the lessons learned from the Constellation Program. A companion Volume II provides more detailed analyses for those seeking further insight and information. In this volume, Section 1.0 introduces the approach in preparing and organizing the content to enable rapid assimilation of the lessons. Section 2.0 describes the contextual framework in which the Constellation Program was formulated and functioned that is necessary to understand most of the lessons. Context of a former program may seem irrelevant in the heady days of new program formulation. However, readers should take some time to understand the context. Many of the lessons would be different in a different context, so the reader should reflect on the similarities and differences in his or her current circumstances. Section 3.0 summarizes key findings developed from the significant lessons learned at the program level that appear in Section 4.0. Readers can use the key findings in Section 3.0 to peruse for particular topics, and will find more supporting detail and analyses in Section 4.0 in a topical format. Appendix A contains a white paper describing the Constellation Program formulation that may be of use to readers wanting more context or background information. The reader will no doubt recognize some very similar themes from previous lessons learned, blue-ribbon committee reviews, National Academy reviews, and advisory panel reviews for this and other large-scale human spaceflight programs; including Apollo, Space Shuttle, Shuttle/Mir, and the ISS. This could represent an inability to learn lessons from previous generations; however, it is more likely that similar challenges persist in the Agency structure and approach to program formulation, budget advocacy, and management. Perhaps the greatest value of these Constellation lessons learned can be found in viewing them in context with these previous efforts to guide and advise the Agency and its

  5. Space station automation study. Automation requirements derived from space manufacturing concepts. Volume 1: Executive summary

    NASA Technical Reports Server (NTRS)

    1984-01-01

    The two manufacturing concepts developed represent innovative, technologically advanced manufacturing schemes. The concepts were selected to facilitate an in depth analysis of manufacturing automation requirements in the form of process mechanization, teleoperation and robotics, and artificial intelligence. While the cost effectiveness of these facilities has not been analyzed as part of this study, both appear entirely feasible for the year 2000 timeframe. The growing demand for high quality gallium arsenide microelectronics may warrant the ventures.

  6. Motivations of Macon County, Tennessee, Manufacturing Milk Producers. A Research Summary of a Graduate Study.

    ERIC Educational Resources Information Center

    Breeding, James Demps; And Others

    A study was conducted to: (1) determine the characteristics of Macon County manufacturing milk producers and their farms; (2) find out which research verified, recommended manufacturing milk production practices were being used by those in the different butterfat production thirds; and (3) try to establish which factors were influential in…

  7. Telescience testbed pilot program, volume 3: Experiment summaries

    NASA Technical Reports Server (NTRS)

    Leiner, Barry M.

    1989-01-01

    Space Station Freedom and its associated labs, coupled with the availability of new computing and communications technologies, have the potential for significantly enhancing scientific research. A Telescience Testbed Pilot Program (TTPP), aimed at developing the experience base to deal with issues in the design of the future information system of the Space Station era. The testbeds represented four scientific disciplines (astronomy and astrophysics, earth science, life sciences, and microgravity sciences) and studied issues in payload design, operation, and data analysis. This volume, of a 3 volume set, which all contain the results of the TTPP, presents summaries of the experiments. This experiment involves the evaluation of the current Internet for the use of file and image transfer between SIRTF instrument teams. The main issue addressed was current network response times.

  8. Midterm Summary of Japan-US Fusion Cooperation Program TITAN

    SciTech Connect

    Muroga, Takeo; Sze, Dai-Kai; Sokolov, Mikhail; Katoh, Yutai; Stoller, Roger E

    2011-01-01

    Japan-US cooperation program TITAN (Tritium, Irradiation and Thermofluid for America and Nippon) started in April 2007 as 6-year project. This is the summary report at the midterm of the project. Historical overview of the Japan-US cooperation programs and direction of the TITAN project in its second half are presented in addition to the technical highlights. Blankets are component systems whose principal functions are extraction of heat and tritium. Thus it is crucial to clarify the potentiality for controlling heat and tritium flow throughout the first wall, blanket and out-of-vessel recovery systems. The TITAN project continues the JUPITER-II activity but extends its scope including the first wall and the recovery systems with the title of 'Tritium and thermofluid control for magnetic and inertial confinement systems'. The objective of the program is to clarify the mechanisms of tritium and heat transfer throughout the first-wall, the blanket and the heat/tritium recovery systems under specific conditions to fusion such as irradiation, high heat flux, circulation and high magnetic fields. Based on integrated models, the breeding, transfer, inventory of tritium and heat extraction properties will be evaluated for some representative liquid breeder blankets and the necessary database will be obtained for focused research in the future.

  9. Survey of US Department of Defense Manufacturing Technology Program activities applicable to civilian manufacturing industries. Final report

    SciTech Connect

    Azimi, S.A.; Conrad, J.L.; Reed, J.E.

    1985-03-01

    Intent of the survey was to identify and characterize activities potentially applicable to improving energy efficiency and overall productivity in the civilian manufacturing industries. The civilian industries emphasized were the general manufacturing industries (including fabricated metals, glass, machinery, paper, plastic, textile, and transportation equipment manufacturing) and the primary metals industries (including primary aluminum, copper, steel, and zinc production). The principal steps in the survey were to: develop overview taxonomies of the general manufacturing and primary metals industries as well as specific industry taxonomies; identify needs and opportunities for improving process energy efficiency and productivity in the industries included; identify federal programs, capabilities, and special technical expertise that might be relevant to industry's needs and opportunities; contact federal laboratories/facilities, through visits and other forms of inquiry; prepare formatted profiles (descriptions) potentially applicable work efforts; review findings with industry; and compile and evaluate industry responses.

  10. MHD magnet technology development program summary, September 1982

    SciTech Connect

    Not Available

    1983-11-01

    The program of MHD magnet technology development conducted for the US Department of Energy by the Massachusetts Institute of Technology during the past five years is summarized. The general strategy is explained, the various parts of the program are described and the results are discussed. Subjects covered include component analysis, research and development aimed at improving the technology base, preparation of reference designs for commercial-scale magnets with associated design evaluations, manufacturability studies and cost estimations, the detail design and procurement of MHD test facility magnets involving transfer of technology to industry, investigations of accessory subsystem characteristics and magnet-flow-train interfacing considerations and the establishment of tentative recommendations for design standards, quality assurance procedures and safety procedures. A systematic approach (framework) developed to aid in the selection of the most suitable commercial-scale magnet designs is presented and the program status as of September 1982 is reported. Recommendations are made for future work needed to complete the design evaluation and selection process and to provide a sound technological base for the detail design and construction of commercial-scale MHD magnets. 85 references.

  11. Extraterrestrial processing and manufacturing of large space systems. Volume 3: Executive summary

    NASA Technical Reports Server (NTRS)

    Miller, R. H.; Smith, D. B. S.

    1979-01-01

    Facilities and equipment are defined for refining processes to commercial grade of lunar material that is delivered to a 'space manufacturing facility' in beneficiated, primary processed quality. The manufacturing facilities and the equipment for producing elements of large space systems from these materials and providing programmatic assessments of the concepts are also defined. In-space production processes of solar cells (by vapor deposition) and arrays, structures and joints, conduits, waveguides, RF equipment radiators, wire cables, converters, and others are described.

  12. Minnesota Mining and Manufacturing Company's hazardous waste program.

    PubMed Central

    Van Noordwyk, H J; Santoro, M A

    1978-01-01

    This paper discusses the present hazardous waste program of 3M Company (Minnesota Mining and Manufacturing Company). 3M's definition of hazardous waste and the company's position on hazardous waste disposal are first considered. The company position is that wherever and whenever the disposal of a waste material threatens the environment or public safety, then that waste should be considered a hazardous waste and treated accordingly in terms of its handling and ultimate disposal. The generation of hazardous wastes and the differentiation of "hazardous" and "nonhazardous" wastes are described next. Handling of hazardous wastes from their generation to their disposal is then covered. This includes a definition of internal 3M terminology and a description of the hazard rating system used by the company. Finally, 3M disposal practices are presented. It is 3M's position that thermal destruction of hazardous wastes, where appropriate, is the best method for their disposal. With this in mind, 3M has constructed incineration facilities throughout the country. The rotary kiln incinerator at the 3M Chemolite plant in Cottage Grove, Minnesota is briefly described. Disposal of certain hazardous wastes in controlled secure land disposal sites is then briefly discussed. PMID:738241

  13. Nez Perce Tribal Hatchery Program : Draft Environmental Impact Statement Summary.

    SciTech Connect

    United States. Bonneville Power Administration; Nez Perce Tribal Hatchery

    1996-06-01

    This summary gives the major points of the Draft Environmental Impact Statement (EIS) prepared for the Nez Perce Tribal Hatchery by the Nez Perce Tribe (NPT), the Bonneville Power Administration (BPA), the Bureau of Indian Affairs (BIA), and other interested parties. The Nez Perce once were one of the largest Plateau tribes in the Northwest and occupied a territory that included north central Idaho, southeastern Washington and northeastern Oregon. Salmon and other migratory fish species are an invaluable food resource and an integral part of the Nez Perce Tribe`s culture. Anadromous fish have always made up the bulk of the Nez Perce tribal diet and this dependence on salmon was recognized in the treaties made with the Tribe by the US. The historic economic, social, and religious significance of the fish to the Nez Perce Tribe continues to this day, which makes the decline of fish populations in the Columbia River Basin a substantial detrimental impact to the Nez Perce way of life. The Nez Perce Tribal Hatchery is a supplementation program that would rear and release spring, summer, and fall chinook (Oncorhynchus tshawytscha), biologically similar to wild fish, to reproduce in the Clearwater River Subbasin. Program managers propose techniques that are compatible with existing aquatic and riparian ecosystems and would integrate hatchery-produced salmon into the stream and river environments needed to complete their life cycle.

  14. NASA OSMA NDE Program Additive Manufacturing Foundational Effort

    NASA Technical Reports Server (NTRS)

    Waller, Jess; Walker, James; Burke, Eric; Wells, Douglas

    2016-01-01

    NASA is providing key leadership in an international effort linking NASA and non-NASA resources to speed adoption of additive manufacturing (AM) to meet NASA's mission goals. Participants include industry, NASA's space partners, other government agencies, standards organizations and academia. Nondestructive Evaluation (NDE) is identified as a universal need for all aspects of additive manufacturing.

  15. MOD-5A wind turbine generator program design report: Volume 1: Executive Summary

    NASA Technical Reports Server (NTRS)

    1984-01-01

    The design, development and analysis of the 7.3 MW MOD-5A wind turbine generator covering work performed between July 1980 and June 1984 is discussed. The report is divided into four volumes: Volume 1 summarizes the entire MOD-5A program, Volume 2 discusses the conceptual and preliminary design phases, Volume 3 describes the final design of the MOD-5A, and Volume 4 contains the drawings and specifications developed for the final design. Volume 1, the Executive Summary, summarizes all phases of the MOD-5A program. The performance and cost of energy generated by the MOD-5A are presented. Each subsystem - the rotor, drivetrain, nacelle, tower and foundation, power generation, and control and instrumentation subsystems - is described briefly. The early phases of the MOD-5A program, during which the design was analyzed and optimized, and new technologies and materials were developed, are discussed. Manufacturing, quality assurance, and safety plans are presented. The volume concludes with an index of volumes 2 and 3.

  16. Summary and recommendations. [reduced gravitational effects on materials manufactured in space

    NASA Technical Reports Server (NTRS)

    1975-01-01

    An economic analysis using econometric and cost benefit analysis techniques was performed to determine the feasibility of space processing of certain products. The overall objectives of the analysis were (1) to determine specific products or processes uniquely connected with space manufacturing, (2) to select a specific product or process from each of the areas of semiconductors, metals, and biochemicals, and (3) to determine the overall price/cost structure of each product or process considered. The economic elements of the analysis involved a generalized decision making format for analyzing space manufacturing, a comparative cost study of the selected processes in space vs. earth manufacturing, and a supply and demand study of the economic relationships of one of the manufacturing processes. Space processing concepts were explored. The first involved the use of the shuttle as the factory with all operations performed during individual flights. The second concept involved a permanent unmanned space factory which would be launched separately. The shuttle in this case would be used only for maintenance and refurbishment. Finally, some consideration was given to a permanent manned space factory.

  17. Product pricing in the Solar Array Manufacturing Industry - An executive summary of SAMICS

    NASA Technical Reports Server (NTRS)

    Chamberlain, R. G.

    1978-01-01

    Capabilities, methodology, and a description of input data to the Solar Array Manufacturing Industry Costing Standards (SAMICS) are presented. SAMICS were developed to provide a standardized procedure and data base for comparing manufacturing processes of Low-cost Solar Array (LSA) subcontractors, guide the setting of research priorities, and assess the progress of LSA toward its hundred-fold cost reduction goal. SAMICS can be used to estimate the manufacturing costs and product prices and determine the impact of inflation, taxes, and interest rates, but it is limited by its ignoring the effects of the market supply and demand and an assumption that all factories operate in a production line mode. The SAMICS methodology defines the industry structure, hypothetical supplier companies, and manufacturing processes and maintains a body of standardized data which is used to compute the final product price. The input data includes the product description, the process characteristics, the equipment cost factors, and production data for the preparation of detailed cost estimates. Activities validating that SAMICS produced realistic price estimates and cost breakdowns are described.

  18. Geothermal energy program summary: Volume 1: Overview Fiscal Year 1988

    NASA Astrophysics Data System (ADS)

    1989-02-01

    Geothermal energy is a here-and-now technology for use with dry steam resources and high-quality hydrothermal liquids. These resources are supplying about 6 percent of all electricity used in California. However, the competitiveness of power generation using lower quality hydrothermal fluids, geopressured brines, hot dry rock, and magma still depends on the technology improvements sought by the DOE Geothermal Energy R and D Program. The successful outcome of the R and D initiatives will serve to benefit the U.S. public in a number of ways. First, if a substantial portion of our geothermal resources can be used economically, they will add a very large source of secure, indigenous energy to the nation's energy supply. In addition, geothermal plants can be brought on line quickly in case of a national energy emergency. Geothermal energy is also a highly reliable resource, with very high plant availability. For example, new dry steam plants at The Geysers are operable over 99 percent of the time, and the small flash plant in Hawaii, only the second in the United States, has an availability factor of 98 percent. Geothermal plants also offer a viable baseload alternative to fossil and nuclear plants -- they are on line 24 hours a day, unaffected by diurnal or seasonal variations. The hydrothermal power plants with modern emission control technology have proved to have minimal environmental impact. The results to date with geopressured and hot dry rock resources suggest that they, too, can be operated so as to reduce environmental effects to well within the limits of acceptability. Preliminary studies on magma are also encouraging. In summary, the character and potential of geothermal energy, together with the accomplishments of DOE's Geothermal R and D Program, ensure that this huge energy resource will play a major role in future U.S. energy markets.

  19. Geothermal energy program summary: Volume 1: Overview Fiscal Year 1988

    SciTech Connect

    Not Available

    1989-02-01

    Geothermal energy is a here-and-now technology for use with dry steam resources and high-quality hydrothermal liquids. These resources are supplying about 6% of all electricity used in California. However, the competitiveness of power generation using lower quality hydrothermal fluids, geopressured brines, hot dry rock, and magma still depends on the technology improvements sought by the DOE Geothermal Energy R and D Program. The successful outcome of the R and D initiatives will serve to benefit the US public in a number of ways. First, if a substantial portion of our geothermal resources can be used economically, they will add a very large source of secure, indigenous energy to the nation's energy supply. In addition, geothermal plants can be brought on line quickly in case of a national energy emergency. Geothermal energy is also a highly reliable resource, with very high plant availability. For example, new dry steam plants at The Geysers are operable over 99% of the time, and the small flash plant in Hawaii, only the second in the United States, has an availability factor of 98%. Geothermal plants also offer a viable baseload alternative to fossil and nuclear plants -- they are on line 24 hours a day, unaffected by diurnal or seasonal variations. The hydrothermal power plants with modern emission control technology have proved to have minimal environmental impact. The results to date with geopressured and hot dry rock resources suggest that they, too, can be operated so as to reduce environmental effects to well within the limits of acceptability. Preliminary studies on magma are also encouraging. In summary, the character and potential of geothermal energy, together with the accomplishments of DOE's Geothermal R and D Program, ensure that this huge energy resource will play a major role in future US energy markets. 7 figs.

  20. Manufacturing technology education development project. Project accomplishment summary for 91-Y12P-050-A1

    SciTech Connect

    Douglass, S.; Smith, R.

    1996-09-25

    The purpose of the project was to provide a set of supplemental instructional equipment and materials to Tennessee high school students to raise their level of knowledge about manufacturing technologies with the hope that some of the best and brightest would choose manufacturing as a career path. The role of the Y-12 Plant was primarily technical: renovate the portable classroom; select and purchase appropriate equipment; install and test the equipment; assist in the development of the curriculum; train the initial group of teachers; and provide technical assistance where needed after the laboratory was deployed. The role of the Department of Education was to provide the mobile facility; assist in the design of the laboratory; lead the development of the curriculum; deploy the trailer; and develop the structure for administering the selection of schools, training teachers, and movement of the laboratory. The Department of Education as subcontracted with Middle Tennessee State University to handle the details of laboratory deployment.

  1. Feasibility of commercial space manufacturing, production of pharmaceuticals. Volume 1: Executive summary

    NASA Technical Reports Server (NTRS)

    1978-01-01

    The feasibility of the commercial manufacturing of pharmaceuticals in space is examined. The method of obtaining pharmaceutical company involvement, laboratory results of the separation of serum proteins by the continuous flow electrophoresis process, the selection and study of candidate products, and their production requirements is presented. Antihemophilic factor, beta cells, erythropoietin, epidermal growth factor, alpha-1-antitrypsin and interferon were studied. Production mass balances for antihemophilic factor, beta cells, and erythropoietin were compared for space verus ground operation.

  2. 3013/9975 Surveillance Program Interim Summary Report

    SciTech Connect

    Dunn, K.; Hackney, B.; McClard, J.

    2011-06-22

    The K-Area Materials Storage (KAMS) Documented Safety Analysis (DSA) requires a surveillance program to monitor the safety performance of 3013 containers and 9975 shipping packages stored in KAMS. The SRS surveillance program [Reference 1] outlines activities for field surveillance and laboratory tests that demonstrate the packages meet the functional performance requirements described in the DSA. The SRS program also supports the complexwide Integrated Surveillance Program (ISP) [Reference 2] for 3013 containers. The purpose of this report is to provide a summary of the SRS portion of the surveillance program activities through fiscal year 2010 (FY10) and formally communicate the interpretation of these results by the Surveillance Program Authority (SPA). Surveillance for the initial 3013 container random sampling of the Innocuous bin and the Pressure bin has been completed and there has been no indication of corrosion or significant pressurization. The maximum pressure observed was less than 50 psig, which is well below the design pressure of 699 psig for the 3013 container [Reference 3]. The data collected during surveillance of these bins has been evaluated by the Materials Identification and Surveillance (MIS) Working Group and no additional surveillance is necessary for these bins at least through FY13. A decision will be made whether additional surveillance of these bins is needed during future years of storage and as additional containers are generated. Based on the data collected to date, the SPA concludes that 3013 containers in these bins can continue to be safely stored in KAMS. This year, 13 destructive examinations (DE) were performed on random samples from the Pressure & Corrosion bin. To date, DE has been completed for approximately 30% of the random samples from the Pressure & Corrosion bin. In addition, DE has been performed on 6 engineering judgment (EJ) containers, for a total of 17 to date. This includes one container that exceeded the 3013

  3. Summary of the general aviation manufacturers' position on aircraft piston engine emissions

    NASA Technical Reports Server (NTRS)

    Helms, J. L.

    1976-01-01

    The General Aviation Manufacturers recommended that the EPA rescind the aircraft piston engine emissions regulations currently on the books. The reason was the very small emission reduction potential and the very poor benefit-cost ratio involved in this form of emission reduction. The limited resources of this industry can far better be devoted to items of much greater benefit to the citizens of this country - reducing noise, improving fuel efficiency (which will incidently reduce exhaust emissions), and improving the safety, operational, and economic aspects of aircraft, all far greater contributions to our total national transportation system.

  4. 75 FR 54073 - Medicaid Program; Withdrawal of Determination of Average Manufacturer Price, Multiple Source Drug...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-09-03

    ... final rule, titled ``Medicaid Program; Prescription Drugs'' in the Federal Register (72 FR 39142...; Withdrawal of Determination of Average Manufacturer Price, Multiple Source Drug Definition, and Upper Limits... determination of average manufacturer price (AMP), and the Federal upper limits (FULs) for multiple source...

  5. A Review of Agile and Lean Manufacturing as Issues in Selected International and National Research and Development Programs and Roadmaps

    ERIC Educational Resources Information Center

    Castro, Helio; Putnik, Goran D.; Shah, Vaibhav

    2012-01-01

    Purpose: The aim of this paper is to analyze international and national research and development (R&D) programs and roadmaps for the manufacturing sector, presenting how agile and lean manufacturing models are addressed in these programs. Design/methodology/approach: In this review, several manufacturing research and development programs and…

  6. An Analysis of National Surveys: Associate Degree Programs in Manufacturing Engineering and Related Programs. A Preliminary Report.

    ERIC Educational Resources Information Center

    Mathias, Elizabeth A.

    In 1993, a study was conducted to investigate the responses of associate degree programs in manufacturing and related technical programs to current technical education initiatives. The study focused on the relationships of associate degree programs to secondary and postsecondary education and industry, curricular trends, familiarity with the…

  7. Status and plans of NASA's Materials Science and Manufacturing in Space (MS/MS) program

    NASA Technical Reports Server (NTRS)

    Armstrong, W. O.; Bredt, J. H.

    1972-01-01

    A description is given of a research and development program on the space shuttle mission designed to prepare the way for possible commercial manufacturing operations on permanently orbiting space stations.

  8. Space station automation study: Automation requirements derived from space manufacturing concepts. Volume 1: Executive summary

    NASA Technical Reports Server (NTRS)

    1984-01-01

    The electroepitaxial process and the Very Large Scale Integration (VLSI) circuits (chips) facilities were chosen because each requires a very high degree of automation, and therefore involved extensive use of teleoperators, robotics, process mechanization, and artificial intelligence. Both cover a raw materials process and a sophisticated multi-step process and are therfore highly representative of the kinds of difficult operation, maintenance, and repair challenges which can be expected for any type of space manufacturing facility. Generic areas were identified which will require significant further study. The initial design will be based on terrestrial state-of-the-art hard automation. One hundred candidate missions were evaluated on the basis of automation portential and availability of meaning ful knowldege. The design requirements and unconstrained design concepts developed for the two missions are presented.

  9. Improving Energy Efficiency at U.S. Plastics Manufacturing Plants: Summary Report and Case Studies

    SciTech Connect

    Not Available

    2005-09-01

    Industrial Technologies Programs BestPractices report based on a comprehensive plant assessment project with ITP's Industrial Assessment Center, The Society of the Plastics Industry, Inc., and several of its member companies.

  10. Enrollment Challenges and "Best Practices" of Selected Two-Year College's Electronic and Manufacturing Programs

    ERIC Educational Resources Information Center

    Jones, Gwendolyn; Hall, Robert A.

    2007-01-01

    The primary purpose of the study was to identify successful electronic and manufacturing engineering programs at two-year colleges that Northeast Community College (a pseudonym) programs can be benched marked against. The project examined two-year college programs for increased enrollment and the number of graduates for the academic years 2000 to…

  11. Biomass energy systems program summary. Information current as of September 30, 1979

    SciTech Connect

    Not Available

    1980-10-01

    This program summary describes each of the DOE's Biomass Energy System's projects funded or in existence during fiscal year 1979 and reflects their status as of September 30, 1979. The summary provides an overview of the ongoing research, development, and demonstration efforts of the preceding fiscal year as well. (DMC)

  12. 23 CFR Appendix B to Part 1200 - Highway Safety Program Cost Summary (HS-217)

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... Summary required to be submitted under 23 CFR 1200.11(e). For subsequent submissions, the amounts in this... 23 Highways 1 2014-04-01 2014-04-01 false Highway Safety Program Cost Summary (HS-217) B Appendix B to Part 1200 Highways NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION AND FEDERAL...

  13. 23 CFR Appendix B to Part 1200 - HIGHWAY SAFETY PROGRAM COST SUMMARY (HS-217)

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... Summary required to be submitted under 23 CFR 1200.11(e). For subsequent submissions, the amounts in this... 23 Highways 1 2013-04-01 2013-04-01 false HIGHWAY SAFETY PROGRAM COST SUMMARY (HS-217) B APPENDIX B TO PART 1200 Highways NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION AND FEDERAL...

  14. Research and Technology Operating Plan Summary, Fiscal Year 1972 Research and Technology Program

    NASA Technical Reports Server (NTRS)

    1971-01-01

    The NASA Research and Technology program for FY 1972 is presented. It is a compilation of the summary portions of each of the RTOPs (Research and Technology Operating Plan) used for management review and control of research currently in progress throughout NASA. The RTOP Summary is designed to facilitate communication and coordination among concerned technical personnel in government, in industry, and in universities.

  15. Artificial intelligence programming languages for computer aided manufacturing

    NASA Technical Reports Server (NTRS)

    Rieger, C.; Samet, H.; Rosenberg, J.

    1979-01-01

    Eight Artificial Intelligence programming languages (SAIL, LISP, MICROPLANNER, CONNIVER, MLISP, POP-2, AL, and QLISP) are presented and surveyed, with examples of their use in an automated shop environment. Control structures are compared, and distinctive features of each language are highlighted. A simple programming task is used to illustrate programs in SAIL, LISP, MICROPLANNER, and CONNIVER. The report assumes reader knowledge of programming concepts, but not necessarily of the languages surveyed.

  16. FY2004 Progress Summary and FY2005 Program Plan Statement of Work and Deliverables

    SciTech Connect

    Meier, W; Bibeau, C

    2006-01-23

    FY2004 progress summary and FY2005 program plan statement of work and deliverables for development of high average power diode-pumped solid state lasers, and complementary technologies for applications in energy and defense.

  17. Summary of the FY 2005 Batteries for Advanced Transportation Technologies (BATT) research program annual review

    SciTech Connect

    None, None

    2005-08-01

    This document presents a summary of the evaluation and comments provided by the review panel for the FY 2005 Department of Energy (DOE) Batteries for Advanced Transportation Technologies (BATT) program annual review.

  18. Texas Educator Excellence Grant (TEEG) Program: Year One Evaluation Report. Policy Evaluation Report. [Executive Summary

    ERIC Educational Resources Information Center

    Springer, Matthew G.; Podgursky, Michael J.; Lewis, Jessica L.; Ehlert, Mark W.; Ghosh-Dastidar, Bonnie; Gronberg, Timothy J.; Hamilton, Laura S.; Jansen, Dennis W.; Lopez, Omar S.; Patterson, Christine H.; Stecher, Brian M.; Taylor, Lori L.

    2008-01-01

    This executive summary presents findings from the first-year evaluation of the Texas Educator Excellence Grant (TEEG) program, one of several statewide performance incentive programs in Texas. In June 2006, Governor Perry and the 79th Texas Legislature created the Governor's Educator Excellence Award Program, one component of which is the TEEG…

  19. Disability Summary Analyses of Select National Data Collection Programs. Technical Report 11.

    ERIC Educational Resources Information Center

    McGrew, Kevin

    This document presents summaries of 28 national data collection programs, to document the amount and nature of information on individuals with disabilities included in the programs. For each program, information provided includes sponsor, purpose, collection cycle, data sources, collection methods, study design, variable domains,…

  20. DHS National Technical Nuclear Forensics Program FY 10 Summary Report: Graduate Mentoring Assistance Program (GMAP)

    SciTech Connect

    Martha R. Finck Ph.D.

    2011-10-01

    This program provides practical training to DHS graduate fellows in the DOE laboratory complex. It involves coordinating students, their thesis advisors, and their laboratory project mentors in establishing a meaningful program of research which contributes to the graduate student's formation as a member of the nuclear forensics community. The summary report details the student/mentor experience and future plans after the first summer practicum. This program provides practical training to DHS graduate fellows in the DOE laboratory complex. It involves coordinating students, their thesis advisors, and their laboratory project mentors in establishing a meaningful program of research which contributes to the graduate student's formation as a member of the nuclear forensics community. This final written report includes information concerning the overall mentoring experience, including benefits (to the lab, the mentors, and the students), challenges, student research contributions, and lab mentor interactions with students home universities. Idaho National Laboratory hosted two DHS Nuclear Forensics graduate Fellows (nuclear engineering) in summer 2011. Two more Fellows (radiochemistry) are expected to conduct research at the INL under this program starting in 2012. An undergraduate Fellow (nuclear engineering) who worked in summer 2011 at the laboratory is keenly interested in applying for the NF Graduate Fellowship this winter with the aim of returning to INL. In summary, this program appears to have great potential for success in supporting graduate level students who pursue careers in nuclear forensics. This relatively specialized field may not have been an obvious choice for some who have already shown talent in the traditional areas of chemistry or nuclear engineering. The active recruiting for this scholarship program for candidates at universities across the U.S. brings needed visibility to this field. Not only does this program offer critical practical training

  1. 77 FR 39265 - Request for Manufacturer Involvement in National Institute of Justice (NIJ) Standard Development...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-07-02

    ... of Justice Programs Request for Manufacturer Involvement in National Institute of Justice (NIJ...: Notice of Request for Manufacturer Involvement in NIJ Standard Development Efforts. SUMMARY: The National... registration information. 2. Participation in webinars. To provide a greater opportunity for involvement...

  2. Automotive Stirling Engine Development Program. RESD summary report

    NASA Technical Reports Server (NTRS)

    1984-01-01

    The design of reference Stirling engine system as well as the engine auxiliaries and controls is described. Manufacturing costs in production quantity are also presented. Engine system performance predictions are discussed and vehicle integration is developed, along with projected fuel economy levels.

  3. An Introduction to Intelligent Processing Programs Developed by the Air Force Manufacturing Technology Directorate

    NASA Technical Reports Server (NTRS)

    Sampson, Paul G.; Sny, Linda C.

    1992-01-01

    The Air Force has numerous on-going manufacturing and integration development programs (machine tools, composites, metals, assembly, and electronics) which are instrumental in improving productivity in the aerospace industry, but more importantly, have identified strategies and technologies required for the integration of advanced processing equipment. An introduction to four current Air Force Manufacturing Technology Directorate (ManTech) manufacturing areas is provided. Research is being carried out in the following areas: (1) machining initiatives for aerospace subcontractors which provide for advanced technology and innovative manufacturing strategies to increase the capabilities of small shops; (2) innovative approaches to advance machine tool products and manufacturing processes; (3) innovative approaches to advance sensors for process control in machine tools; and (4) efforts currently underway to develop, with the support of industry, the Next Generation Workstation/Machine Controller (Low-End Controller Task).

  4. Southern Pennsylvania's Industrial Pipeline: "Pathways" Program Helps Local Manufacturers Find Quality Workers

    ERIC Educational Resources Information Center

    Dixon, John; Girifalco, Tony; Yakabosky, Walt

    2008-01-01

    This article describes the Applied Engineering Technology (AET) Career and Educational Pathways Program, which helps local manufacturers find quality workers. The program features 32 high schools, three community colleges, and 10 four-year institutions offering an integrated regional system of applied engineering education. The goal is to enroll…

  5. The Rhode Island Statewide Lighting Program. Summary report

    SciTech Connect

    Pierce, B.; Bjoerkqvist, O.

    1992-02-01

    This report summarizes the implementation and initial evaluation of the nation`s first statewide conservation and load management program, the Rhode Island Statewide Lighting Program (RISLP). Rhode Island`s program is unique because it is a voluntary collaborative effort and because three utilities use a single delivery mechanism for their programs. The Rhode Island Statewide Lighting Program is a unique attempt to improve the efficiency of electricity use in the commercial/industrial sector on a statewide basis. The cooperative nature of program design and implementation has strengthened communication among the participants. The process evaluation showed that both the participants and the customers are satisfied with the program. The program has had a significant effect on customer behavior.

  6. THE EXTENDED SUMMER PROGRAM, A TWO YEAR SUMMARY.

    ERIC Educational Resources Information Center

    CATON, JAY; AND OTHERS

    TO PROVIDE TEACHERS WITH TRAINING IN TEAM TEACHING, NONGRADING, AND EFFECTIVE STAFF UTILIZATION AS A MEANS OF IMPROVING PUPIL INSTRUCTION, THE EXTENDED SUMMER PROGRAM WAS CONDUCTED IN 1965 AND 1966. THE PROGRAM WAS STRUCTURED SO THAT (1) TEACHERS WERE RECRUITED FOR SPECIFIC ROLES IN A FULL-DAY PROGRAM, (2) EACH TEACHER UNDERWENT ORIENTATION…

  7. Alpena Community College Commercial Driver's License Program. Evaluation Summary.

    ERIC Educational Resources Information Center

    Alpena Community Coll., MI.

    The Alpena Community College (ACC) Drivers Education Program was developed to deliver a basic skills program providing specific job-related basic skills instruction to approximately 300 workers throughout Michigan who desired to pass the Commercial Drivers License (CDL) examination. Other program goals were to establish greater partnerships…

  8. Subscale Beryllium Mirrors Demonstrator (SBMD) Program Summary and Ball Modeling

    NASA Technical Reports Server (NTRS)

    Kendrick, Stephen; Brown, Robert; Stahl, Philip (Technical Monitor)

    2001-01-01

    The SBMD Program was to design, fabricate, and test a 0.5-m beryllium lightweighted mirror applicable to space deployable systems with demanding optical and areal density requirements. This presentation summarizes the program's objectives and the mirror's tested technical performance along with lessons learned. In addition, test results are compared to modeling predictions. The SBMD Program was funded by NASA MSFC.

  9. NARC Rayon Replacement Program for the Space Shuttle Reusable Solid Rocket Motor Nozzle: Screening Summary

    NASA Technical Reports Server (NTRS)

    Cook, R. V.; Fairbourn, M. W.; Wendel, G. M.

    2000-01-01

    Thiokol Corporation and NASA MSFC are jointly developing a replacement for North American Rayon Corporation (NARC) Aerospace Grade Rayon (1650/720 continuous filament), the precursor for the Carbon Cloth Phenolic (CCP) ablatives used in the Space Shuttle Reusable Solid Rocket Motor (RSRM) Nozzles. NARC discontinued production of Aerospace Grade Rayon in September 1997. NASA maintains a stockpile of NARC Rayon to support RSRM production through the summer of 2005. The program plan for selection and qualification of a replacement for NARC rayon was approved in August 1998. Screening activities began in February 1999. The intent of this paper is to provide a summary of the data generated during the screening phase of the NARC Rayon Replacement Program. Twelve cellulose based fibers (rayon and lyocell) were evaluated. These fibers were supplied by three independent vendors. Many of these fibers were carbonized by two independent carbonizers. Each candidate was tested according to standard acceptance test methods at each step of the manufacturing process. Additional testing was performed with the candidate CCPS, including hot fire tests, Process studies and mechanical and thermal characterization. Six of the twelve fiber candidates tested were dropped at the conclusion of Phase 1. The reasons for the elimination of these candidates included; difficulties in processing the material in the whitegoods, carbon and CCP forms; poor composite mechanical performance; and future availability concerns. The remaining six fibers demonstrated enough promise to merit continued evaluation and optimization of the CCP fabrication process. Note: Certain CCP data falls under the restrictions of US export laws, (ITAR, etc.) and will not be included in this paper.

  10. Commercial Electric Vehicle (EV) Development and Manufacturing Program

    SciTech Connect

    Leeve, Dion

    2014-06-30

    Navistar with the Department of Energy’s assistance undertook this effort to achieve the project objectives as listed in the next section. A wholly owned subsidiary of Navistar, Workhorse Sales Corporation was the original grant awardee and upon their discontinuation as a standalone business entity, Navistar assumed the role of principal investigator. The intent of the effort, as part of the American Recovery and Reinvestment Act (ARRA) was to produce zero emission vehicles that could meet the needs of the marketplace while reducing carbon emissions to zero. This effort was predicated upon the assumption that concurrent development activities in the lithium ion battery industry investigations would significantly increase their production volumes thus leading to substantial reductions in their manufacturing costs. As a result of this development effort much was learned about the overall system compatibility between the electric motor, battery pack, and charging capabilities. The original system was significantly revised and improved during the execution of this development effort. The overall approach that was chosen was to utilize a British zero emissions, class 2 truck that had been developed for their market, homologate it and modify it to meet the product requirements as specified in the grant details. All of these specific goals were achieved. During the course of marketing and selling the product valuable information was obtained as relates to customer expectations, price points, and product performance expectations, specifically those customer expectations about range requirements in urban delivery situations. While the grant requirements specified a range of 100 miles on a single charge, actual customer usage logs indicate a range of 40 miles or less is typical for their applications. The price point, primarily due to battery pack costs, was significantly higher than the mass market could bear. From Navistar’s and the overall industry’s perspective

  11. 75 FR 57230 - 340B Drug Pricing Program Manufacturer Civil Monetary Penalties

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-09-20

    ...Section 602 of Public Law 102-585, the ``Veterans Health Care Act of 1992'' enacted Section 340B of the Public Health Service Act (PHSA). Section 340B implements a drug pricing program by which manufacturers enter into an agreement to sell covered outpatient drugs to particular covered entities at a price not exceeding the amount determined under a statutory formula. Manufacturers are required......

  12. Summary of residential environmental issues and program consistency

    SciTech Connect

    Baechler, M C

    1989-05-01

    The Northwest Power Planning Act authorizes the Bonneville Power Administration to acquire all necessary energy resources to serve Northwest utilities choosing to acquire power from the agency and to give conservation the highest priority in responding to the demand for electricity. To meet this mandate, the agency has established residential conservation programs for weatherizing existing homes, building new energy-efficient homes, and promoting energy-efficient appliances. Pacific Northwest Laboratory prepared this report to compare and contrast the environmental requirements and issues involving Bonneville's residential conservation programs. The key environmental concern confronting each of the programs with measures aimed at reducing air leakage rates in houses (both new and existing) is indoor air quality (IAQ). This report reviews the similarity and consistency of the programs' approach to IAQ, their impacts, program features, mitigation techniques, and new information about IAQ and other potential environmental issues confronting the programs. The information is intended for use in comparing and contrasting how environmental features mesh with other program features, checking consistency across programs and determining whether it makes sense for programs to be consistent, determining consistency between programs, and providing information to aid program planning in light of potential environmental issues and new information. 31 refs.

  13. Economics and utility energy-efficiency programs: Energy-efficient manufactured housing

    SciTech Connect

    Lee, A.D.; Onisko, S.A.

    1992-10-01

    As utilities investigate ways to implement conservation programs, the differences between customer and utility economic perspectives become more important. Because utilities bear the cost of new energy sources, energy efficiency investments that are cost-effective to them may not be cost-effective to their customers who pay average energy prices and have different economic parameters. The Bonneville Power Administration (BPA) and other parties in the Pacific Northwest have initiated an innovative manufactured (mobile) home energy conservation program. Because manufactured homes are regulated by the Department of Housing and Urban Development (HUD), are exempt from local regulations, and comprise up to 50% of new housing starts in some parts of the United States, utilities and energy planners need to find creative ways to make the economics of manufactured housing energy-efficiency investments more attractive. Differences between the economic criteria and perspectives of consumers and utilities can be used to design energy-efficiency programs. This paper discusses life-cycle cost (LCC) analysis as a framework for highlighting these differences and examines other economic criteria. It then presents information from the Pacific Northwest manufactured housing program to illustrate the application of this framework to a real-world program. Findings from this program should,be of interest to utility and government planners who are designing innovative energy-efficiency programs.

  14. Summary

    SciTech Connect

    Itoh, Kimitaka

    2009-02-19

    In this presentation, lectures in the school are revisited and a brief summary is given. An emphasis is made to illustrate how the lectures are interconnected so as to constitute the unified basis of knowledge in realizing thermonuclear fusion in ITER.The first message here is the integration of the knowledge. All of conditions (which is imposed by individual characteristic dynamics) must be simultaneously fulfilled. Plasma conditions (density, pressure, current, shape, etc.) set parameter boundaries. Achievement of Q = 10 is expected to be realized near the ridge of boundary, so that exact knowledge of mutual relations between constraints is inevitable. The other message is that, the constraints of plasma, material and design must be subject to a special care. In this regard, the use of tritium in ITER introduces new issue in research. For instance, the containment of tritium in the device leads to a new demand for the system. This issue influences the choice of the wall material. The difference of the wall material (either light element or heavy metal), on the other hand, can have a large impact on confinement. These new features in integration will be explained.The other issue is the need of integration of knowledge to form a law of understanding. The mission of ITER must be realized as fast as possible, considering the fact the necessity for fusion energy will be more keen as time goes on. The operation of ITER has been predicted by extending the empirical scaling relations. More precise prediction and the resolution of possible problems in advance are required. For this urgency, our knowledge must be distilled as a scientific law in which elementary processes are validated.

  15. Bellingham Bay action program: Initial data summaries and problem identification

    SciTech Connect

    Decker, D.S.; Sonnerup, R.; Greene, J.J.

    1989-08-01

    The report provides a synthesis of information describing the geographic extent and severity of estuarine contamination in Bellingham Bay within Puget Sound in Washington State. Summaries of existing data are provided for chemical contamination of sediment and biota, microbial contamination, eutrophication and contaminant sources. Original, summarized, tabulated, and mapped data are presented. The objective of the report is to provide a mechanism for comprehensively evaluating pollution problems in the more urbanized embayments and for providing a basis for prioritizing corrective actions. A decision making framework is presented for evaluating and prioritizing both sub-areas within Bellingham Bay and specific contaminant sources.

  16. An Evaluation of the Right to Read Inexpensive Book Distribution Program. Executive Summary.

    ERIC Educational Resources Information Center

    General Research Corp., McLean, VA.

    This document is an executive summary of a study examining the Inexpensive Book Distribution Program (IBDP), a federally funded and sponsored program operated by Reading is Fundamental (RIF). Sections of the report provide the following information: (1) methodology and procedures for conducting the study, (2) a brief description of RIF national…

  17. An Evaluation of the Nutrition Education and Training Program: Project Summary.

    ERIC Educational Resources Information Center

    St. Pierre, Robert G.

    This project summary reviews and extends the findings of prior reports made by Abt Associates, Inc. (Cambridge, Massachusetts) on the Nutrition Education and Training (NET) program, synthesizes evaluation efforts in nutrition education, and presents a set of conclusions based on the evaluations of nutrition programs. Chapter 1 presents background…

  18. Evaluation of the Emergency School Assistance Program. Volume I: Summary. Final Report.

    ERIC Educational Resources Information Center

    RMC Research Corp., Arlington, VA.

    The Emergency School Assistance Program (ESAP) was developed as a Federal program to aid local education agencies (LEAs) in achieving and adjusting to recent racial desegregation of their public school systems. This is one of three volumes that constitute the final report of the evaluation of the ESAP. In Volume I, a summary of the overall study…

  19. SUMMARY OF EMISSIONS MANAGEMENT STRATEGY POLICY RELEVANT FINDINGS FROM EPA'S PM SUPERSITES PROGRAM

    EPA Science Inventory

    EPA is developing an integrated synthesis of key scientific and policy-relevant findings from EPA's Particulate Matter Supersites Program. This presentation provides a summary of the program and the integrated synthesis. Since there are many examples of such findings, ranging f...

  20. FWP executive summaries. Basic Energy Sciences/Materials Sciences Programs (SNL/NM)

    SciTech Connect

    Samara, G.A.

    1994-01-01

    This report is divided into: budget, capital equipment requests, general programmatic overview and institutional issues, DOE center of excellence for synthesis and processing of advanced materials, industrial interactions and technology transfer, and research program summaries (new proposals, existing programs). Ceramics, semiconductors, superconductors, interfaces, CVD, tailored surfaces, adhesion, growth and epitaxy, boron-rich solids, nanoclusters, etc. are covered.

  1. Annual Program. Library Services and Construction Act, 1986-1987, and FY 1986 Summary.

    ERIC Educational Resources Information Center

    South Carolina State Library, Columbia.

    This document comprises the Library Services and Construction Act (LSCA) 1986-1987 annual program and the FY 86 LSCA summary for the South Carolina State Library. The annual program includes fiscal information and project descriptions for the following LSCA projects: (1) Title I--Library Services, including Projects IA--General Administration,…

  2. Building Management Information Systems to Coordinate Citywide Afterschool Programs: A Toolkit for Cities. Executive Summary

    ERIC Educational Resources Information Center

    Kingsley, Chris

    2012-01-01

    This executive summary describes highlights from the report, "Building Management Information Systems to Coordinate Citywide Afterschool Programs: A Toolkit for Cities." City-led efforts to build coordinated systems of afterschool programming are an important strategy for improving the health, safety and academic preparedness of children and…

  3. The Schools Attuned Program Core Course: 2004 Participant Evaluation. Executive Summary

    ERIC Educational Resources Information Center

    All Kinds of Minds, 2005

    2005-01-01

    This executive summary presents program evaluation outcomes for the Core Course component of the Schools Attuned Program. Core Courses occurred in sites across the United States, Canada and in Zurich, Switzerland throughout 2004. Analyses are based on information from the Schools Attuned Participant Core Course Survey and Schools Attuned…

  4. Intensive Aftercare for High-Risk Juveniles: A Community Care Model. Program Summary.

    ERIC Educational Resources Information Center

    Altschuler, David M.; Armstrong, Troy L.

    Crowded juvenile correctional centers, escalating costs of confinement, and high rates of recidivism have renewed interest in bringing innovative ideas to juvenile aftercare philosophy, practice, and programming. This program summary details an Office of Juvenile Justice and Delinquency Prevention initiative designed to assist public and private…

  5. Preventing Youth Violence. A Summary of Program Evaluations. Urban Health Initiative Monograph Series, Monograph 1.

    ERIC Educational Resources Information Center

    Kellermann, Arthur L.; Fuqua-Whitley, Dawna S.; Rivara, Frederick P.

    This summary explaining the results of evaluations of programs to prevent youth violence is an attempt to fill the gap in information about what works and what does not. An effort is made to place the problem of youth violence in perspective, using information largely taken from Bureau of Justice statistics. The existing programs are divided into…

  6. Onsite 40-kilowatt fuel cell power plant manufacturing and field test program

    NASA Technical Reports Server (NTRS)

    1985-01-01

    A joint Gas Research Institute and U.S. Department of Energy Program was initiated in 1982 to evaluate the use of fuel cell power systems for on-site energy service. Forty-six 40 kW fuel cell power plants were manufactured at the United Technologies Corporation facility in South Windsor, Connecticut, and are being delivered to host utilities and other program participants in the United States and Japan for field testing. The construction of the 46 fully-integrated power plants was completed in January 1985 within the constraints of the contract plan. The program has provided significant experience in the manufacture, acceptance testing, deployment, and support of on-site fuel cell systems. Initial field test results also show that these experimental power plants meet the performance and environmental requirements of a commercial specification. This Interim Report encompasses the design and manufacturing phases of the 40 kW Power Plant Manufacturing and Field Test program. The contract between UTC and NASA also provides UTC field engineering support to the host utilities, training programs and associated manuals for utility operating and maintenance personnel, spare parts support for a defined test period, and testing at UTC of a power plant made available from a preceding program phase. These activities are ongoing and will be reported subsequently.

  7. Onsite 40-kilowatt fuel cell power plant manufacturing and field test program

    NASA Astrophysics Data System (ADS)

    1985-02-01

    A joint Gas Research Institute and U.S. Department of Energy Program was initiated in 1982 to evaluate the use of fuel cell power systems for on-site energy service. Forty-six 40 kW fuel cell power plants were manufactured at the United Technologies Corporation facility in South Windsor, Connecticut, and are being delivered to host utilities and other program participants in the United States and Japan for field testing. The construction of the 46 fully-integrated power plants was completed in January 1985 within the constraints of the contract plan. The program has provided significant experience in the manufacture, acceptance testing, deployment, and support of on-site fuel cell systems. Initial field test results also show that these experimental power plants meet the performance and environmental requirements of a commercial specification. This Interim Report encompasses the design and manufacturing phases of the 40 kW Power Plant Manufacturing and Field Test program. The contract between UTC and NASA also provides UTC field engineering support to the host utilities, training programs and associated manuals for utility operating and maintenance personnel, spare parts support for a defined test period, and testing at UTC of a power plant made available from a preceding program phase. These activities are ongoing and will be reported subsequently.

  8. 40 CFR 130.0 - Program summary and purpose.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Section 130.0 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS WATER... and program requirements for water quality planning, management and implementation under sections 106, 205(j), non-construction management 205(g), 208, 303 and 305 of the Clean Water Act. The Water...

  9. 40 CFR 130.0 - Program summary and purpose.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... Section 130.0 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS WATER... and program requirements for water quality planning, management and implementation under sections 106, 205(j), non-construction management 205(g), 208, 303 and 305 of the Clean Water Act. The Water...

  10. 40 CFR 130.0 - Program summary and purpose.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Section 130.0 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS WATER... and program requirements for water quality planning, management and implementation under sections 106, 205(j), non-construction management 205(g), 208, 303 and 305 of the Clean Water Act. The Water...

  11. 40 CFR 130.0 - Program summary and purpose.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Section 130.0 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS WATER... and program requirements for water quality planning, management and implementation under sections 106, 205(j), non-construction management 205(g), 208, 303 and 305 of the Clean Water Act. The Water...

  12. 40 CFR 130.0 - Program summary and purpose.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Section 130.0 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS WATER... and program requirements for water quality planning, management and implementation under sections 106, 205(j), non-construction management 205(g), 208, 303 and 305 of the Clean Water Act. The Water...

  13. FY 1978 aeronautics and space technology program summary

    NASA Technical Reports Server (NTRS)

    1977-01-01

    Highlights of the aeronautics program include research on aircraft energy efficiency, supersonic cruise aircraft, vertical takeoff and landing aircraft, short haul/short takeoff and landing aircraft, and general aviation aircraft. The space technology program includes work on space structures, propulsion systems, power systems, materials, and electronics.

  14. Child Nutrition Program Operations Study: First Year Report Executive Summary.

    ERIC Educational Resources Information Center

    St. Pierre, Robert; And Others

    Summarizing the first year report of a multi-year study of the Food and Nutrition Service's (Department of Agriculture) Child Nutrition Programs, this report describes the programs and methods of the study. Data were collected through telephone interviews with states and School Food Authorities (SFAs) between 1987 and 1992. Findings from 1987-1988…

  15. Obesity, Poverty, and Participation in Nutrition Assistance Programs: Summary.

    ERIC Educational Resources Information Center

    US Department of Agriculture, 2005

    2005-01-01

    The national nutrition safety net consists of 15 programs that provide millions of low-income Americans access to a healthy and nutritious diet. It has been observed that many low income individuals are both overweight and participants in one or more nutrition assistance programs. This has led some to question whether participation in the…

  16. YES in Action: Youth Environmental Service Program Summary.

    ERIC Educational Resources Information Center

    Office of Juvenile Justice and Delinquent Prevention (Dept. of Justice), Washington, DC.

    The Youth Environmental Service (YES) aims to rehabilitate adjudicated delinquents and to prevent at-risk youth from entering the juvenile justice system by engaging them in environmental work and education programs on federally owned land. YES is a joint program of the U.S. Department of the Interior (DOI) and the Office of Juvenile Justice and…

  17. Summary of Granulation Matrix Testing for the Plutonium Immobilization Program

    SciTech Connect

    Herman, C.C.

    2001-10-19

    In FY00, a matrix for process development testing was created to identify those items related to the ceramic process that had not been fully developed or tested and to help identify variables that needed to be tested. This matrix, NMTP/IP-99-003, was jointly created between LLNL and SRTC and was issued to all affected individuals. The matrix was also used to gauge the progress of the development activities. As part of this matrix, several series of tests were identified for the granulation process. This summary provides the data and results from the granulation testing. The results of the granulation matrix testing were used to identify the baseline process for testing in the PuCTF with cold surrogates in B241 at LLNL.

  18. Systems autonomy technology: Executive summary and program plan

    NASA Technical Reports Server (NTRS)

    Bull, John S (Editor)

    1987-01-01

    The National Space Strategy approved by the President and Congress in 1984 sets for NASA a major goal of conducting effective and productive space applications and technology programs which contribute materially toward United States leadership and security. To contribute to this goal, OAST supports the Nation's civil and defense space programs and overall economic growth. OAST objectives are to ensure timely provision of new concepts and advanced technologies, to support both the development of NASA missions in space and the space activities of industry and other organizations, to utilize the strengths of universities in conducting the NASA space research and technology program, and to maintain the NASA centers in positions of strength in critical space technology areas. In line with these objectives, NASA has established a new program in space automation and robotics that will result in the development and transfer and automation technology to increase the capabilities, productivity, and safety of NASA space programs including the Space Station, automated space platforms, lunar bases, Mars missions, and other deep space ventures. The NASA/OAST Automation and Robotics program is divided into two parts. Ames Research Center has the lead role in developing and demonstrating System Autonomy capabilities for space systems that need to make their own decisions and do their own planning. The Jet Propulsion Laboratory has the lead role for Telerobotics (that portion of the program that has a strong human operator component in the control loop and some remote handling requirement in space). This program is intended to be a working document for NASA Headquarters, Program Offices, and implementing Project Management.

  19. Summary of results of NASA F-15 flight research program

    NASA Technical Reports Server (NTRS)

    Burcham, F. W., Jr.; Trippensee, G. A.; Fisher, D. F.; Putnam, T. W.

    1986-01-01

    NASA conducted a multidisciplinary flight research program on the F-15 airplane. The program began in 1976 when two preproduction airplanes were obtained from the U.S. Air Force. Major projects involved stability and control, handling qualities, propulsion, aerodynamics, propulsion controls, and integrated propulsion-flight controls. Several government agencies and aerospace contractors were involved. In excess of 330 flights were flown, and over 85 papers and reports were published. This document describes the overall program, the projects, and the key results. The F-15 was demonstrated to be an excellent flight research vehicle, producing high-quality results.

  20. Advanced Thermionic Technology Program: summary report. Volume 4. Final report

    SciTech Connect

    Not Available

    1984-10-01

    This report summarizes the progress made by the Advanced Thermionic Technology Program during the past several years. This Program, sponsored by the US Department of Energy, has had as its goal adapting thermionic devices to generate electricity in a terrestrial (i.e., combustion) environment. Volume 4 (Part E) is a highly technical discussion of the attempts made by the Program to push the state-of-the-art beyond the current generation of converters and is directed toward potential researchers engaged in this same task. These technical discussions are complemented with Appendices where appropriate.

  1. Northwest Energy Efficient Manufactured Housing Program Specification Development

    SciTech Connect

    Hewes, T.; Peeks, B.

    2013-02-01

    The Hood River Passive Project was developed by Root Design Build of Hood River Oregon using the Passive House Planning Package (PHPP) to meet all of the requirements for certification under the European Passive House standards. The Passive House design approach has been gaining momentum among residential designers for custom homes and BEopt modeling indicates that these designs may actually exceed the goal of the U.S. Department of Energy's (DOE) Building America program to reduce home energy use by 30%-50% (compared to 2009 energy codes for new homes). This report documents the short term test results of the Shift House and compares the results of PHPP and BEopt modeling of the project.

  2. AICD -- Advanced Industrial Concepts Division Biological and Chemical Technologies Research Program. 1993 Annual summary report

    SciTech Connect

    Petersen, G.; Bair, K.; Ross, J.

    1994-03-01

    The annual summary report presents the fiscal year (FY) 1993 research activities and accomplishments for the United States Department of Energy (DOE) Biological and Chemical Technologies Research (BCTR) Program of the Advanced Industrial Concepts Division (AICD). This AICD program resides within the Office of Industrial Technologies (OIT) of the Office of Energy Efficiency and Renewable Energy (EE). The annual summary report for 1993 (ASR 93) contains the following: A program description (including BCTR program mission statement, historical background, relevance, goals and objectives), program structure and organization, selected technical and programmatic highlights for 1993, detailed descriptions of individual projects, a listing of program output, including a bibliography of published work, patents, and awards arising from work supported by BCTR.

  3. Atmospheric Science Program. Summaries of research in FY 1994

    SciTech Connect

    1995-06-01

    This report provides descriptions for all projects funded by ESD under annual contracts in FY 1994. Each description contains the project`s title; three-year funding history (in thousands of dollars); the contract period over which the funding applies; the name(s) of the principal investigator(s); the institution(s) conducting the projects; and the project`s objectives, products, approach, and results to date (for most projects older than one year). Project descriptions are categorized within the report according to program areas: atmospheric chemistry, atmospheric dynamics, and support operations. Within these categories, the descriptions are ordered alphabetically by principal investigator. Each program area is preceded by a brief text that defines the program area, states it goals and objectives, lists principal research questions, and identifies program managers. Appendixes provide the addresses and telephone numbers of the principal investigators and define the acronyms used.

  4. The Superfund Innovative Technology Evaluation Program SUMMARY AND CLOSURE REPORT

    EPA Science Inventory

    The Superfund Innovative Technology Evaluation (SITE) Program promoted the development, commercialization, and implementation of innovative hazardous waste treatment technologies for 20 years. SITE offered a mechanism for conducting joint technology demonstration and evaluation ...

  5. CRRES: Combined release and radiation effects satellite program summary

    NASA Technical Reports Server (NTRS)

    Layman, Laura D.; Miller, George P.

    1993-01-01

    The experiments that comprise the Combined Release and Radiation Effects Satellite Program (CRRES) (Apr. 1990 - Jul. 1992) are presented. The experiments are as follows: PEGSAT; El Coqui; the Kwajalein Campaign; and experiments G1 - G14.

  6. Summary of the Savannah River Site Criticality Dosimetry Program

    SciTech Connect

    Crase, K.W.

    1993-02-01

    The mission of the Savannah River Site (SRS) includes working with fissionable materials. A program is in place, therefore, to assess neutron and gamma doses to individuals in the event of a criticality accident at SRS. The program consists of a method to quickly screen for potentially exposed personnel, a method to provide early but preliminary dose estimates, and a nuclear accident dosimeter and assay procedure to enable final dose estimates.

  7. 9975 SHIPPING PACKAGE LIFE EXTENSION SURVEILLANCE PROGRAM RESULTS SUMMARY

    SciTech Connect

    Daugherty, W.; Dunn, K.; Hackney, B.; Hoffman, E.; Skidmore, E.

    2011-01-06

    Results from the 9975 Surveillance Program at the Savannah River Site (SRS) are summarized for justification to extend the life of the 9975 packages currently stored in the K-Area Materials Storage (KAMS) facility from 10 years to 15 years. This justification is established with the stipulation that surveillance activities will continue throughout this extended time to ensure the continued integrity of the 9975 materials of construction and to further understand the currently identified degradation mechanisms. The current 10 year storage life was developed prior to storage. A subsequent report was later used to extend the qualification of the 9975 shipping packages for 2 years for shipping plus 10 years for storage. However the qualification for the storage period was provided by the monitoring requirements of the Storage and Surveillance Program. This report summarizes efforts to determine a new safe storage limit for the 9975 shipping package based on the surveillance data collected since 2005 when the surveillance program began. KAMS is a zero-release facility that depends upon containment by the 9975 to meet design basis storage requirements. Therefore, to confirm the continued integrity of the 9975 packages while stored in KAMS, a 9975 Storage and Surveillance Program was implemented alongside the DOE required Integrated Surveillance Program (ISP) for 3013 plutonium-bearing containers. The 9975 Storage and Surveillance Program performs field surveillance as well as accelerated aging tests to ensure any degradation due to aging, to the extent that could affect packaging performance, is detected in advance of such degradation occurring in the field. The Program has demonstrated that the 9975 package has a robust design that can perform under a variety of conditions. As such the primary emphasis of the on-going 9975 Surveillance Program is an aging study of the 9975 Viton(reg.sign) GLT containment vessel O-rings and the Celotex(reg.sign) fiberboard thermal

  8. SFD-261 crossed-field amplifier manufacturing technology program

    NASA Astrophysics Data System (ADS)

    Laplante, R. A.; Trojan, F. E.

    1980-09-01

    The objective of the MT program is to demonstrate improved production techniques by a pilot production run of ten (10) tubes to meet performance specification and system compatibility criteria under production line conditions. The SFD-261 is a microwave amplifier used to increase the power level of pulses of energy by a factor of 20. It is used in the Aegis AN/SPY-1 radar transmitter. A single ship's complement without spares is seventy-six. Its internal parts are made from high purity copper and many are complex and involve high precision. Most of the fabrication is by precious metal brazing in hydrogen or in vacuum. Modest production rates (10 to 30 units per month) presently restrict the amount of automation which can be effectively applied. Nearly 30 design changes were made without altering performance significantly. Self-jigging techniques permitted assembly by lower skill levels. A 'one-shot' vacuum braze for the cathode produced significant cost and equipment reduction. If the selling price of the standard design is normalized at 100, the price of the MT design is now 57.

  9. 9975 SHIPPING PACKAGE LIFE EXTENSION SURVEILLANCE PROGRAM RESULTS SUMMARY

    SciTech Connect

    Dunn, K.; Daugherty, W.; Hackney, B.; Hoffman, E.; Skidmore, E.

    2011-05-27

    Results from the 9975 shipping package Storage and Surveillance Program at the Savannah River Site (SRS) are summarized for justification to extend the life of the 9975 packages currently stored in the K-Area Complex (KAC). This justification is established with the stipulation that surveillance activities will continue throughout the extended time to ensure the continued integrity of the 9975 materials of construction and to further understand the currently identified degradation mechanisms. The 10 year storage life justification was developed prior to storage. A subsequent report was later used to validate the qualification of the 9975 shipping packages for 10 years in storage. However the qualification for the storage period was provided by the monitoring requirements of the 9975 Storage and Surveillance Program. This report summarizes efforts to determine a new safe storage limit for the 9975 shipping package based on the surveillance data collected since 2005 when the 9975 Storage and Surveillance Program began. The Program has demonstrated that the 9975 package has a robust design that can perform under a variety of conditions. The primary emphasis of the on-going 9975 Storage and Surveillance Program is an aging study of the 9975 Viton{reg_sign} containment vessel O-rings and the Celotex{reg_sign} fiberboard thermal insulation at bounding conditions of radiation, elevated temperatures and/or elevated humidity.

  10. Atmospheric Sciences Program summaries of research in FY 1993

    SciTech Connect

    Not Available

    1993-11-01

    This document describes the activities and products of the Atmospheric Science Program of the Environmental Sciences Division, Office of Health and Environmental Research, Office of Energy Research, in FY 1993. Each description contains the project`s title; three-year funding history; the contract period over which the funding applies; the name(s) of the principal investigator(s); the institution(s) conducting the projects; and the project`s objectives, products, approach, and results to date. Project descriptions are categorized within the report according to program areas: atmospheric chemistry, atmospheric dynamics, and support operations. Within these categories, the descriptions are ordered alphabetically by principal investigator. Each program area is preceded by a brief text that defines the program area, states its goals and objectives, lists principal research questions, and identifies program managers. Appendixes provide the addresses and telephone numbers of the principal investigators and define the acronyms used. This document has been indexed to aid the reader in locating research topics, participants, and research institutions in the text and the project descriptions. Comprehensive subject, principal investigator, and institution indexes are provided at the end of the text for this purpose. The comprehensive subject index includes keywords from the introduction and chapter texts in addition to those from the project descriptions.