Interdiffusion of NaSi—CaAl in peristerite

NASA Astrophysics Data System (ADS)

Yund, Richard A.

1986-01-01

The ‘average’ interdiffusion coefficient (bar D) for NaSi—CaAl exchange in plagioclase for the interval from An0 to An26 was estimated from experimentally determined homogenization times for peristerite exsolution lamellae. The average spacing between adjacent (unlike) lamellae is 554±77 Å. Dry heating in air at 1,100°C for 98 days produced no change in the exsolution microstructure; thus bar D(dry)<10-17 cm2/s. This limit is consistent with the recently reported ‘average’ bar D(dry) values for the Huttenlocher interval (An70 90) at this temperature. At 1.5 GPa with about 0.2 weight percent water added the ‘average’ diffusion coefficient from 1,100°C to 900°C is given by: bar D(wet)=18{-15/+108}(cm2/s) exp (-97±5 (kcal/mol)/RT), where R is the gas constant, and T is °K. This bar D(wet) at 1,100°C is more than three orders of magnitude greater than bar D(dry) for Na- and Ca-rich plagioclases.

3D organic Na4C6O6/graphene architecture for fast sodium storage with ultralong cycle life.

PubMed

Gu, Jianan; Gu, Yue; Yang, Shubin

2017-11-23

Sodium-ion batteries (SIBs) have aroused increasing interest as one of the most promising replacements for lithium-ion batteries (LIBs). Here, a novel organic-inorganic 3D Na 4 C 6 O 6 -graphene architecture was successfully fabricated from commercial Na 2 C 6 O 6 and for the first time applied for sodium storage. Hence, the 3D Na 4 C 6 O 6 -graphene architecture exhibits a high reversible capacity, good cyclic performance and high-rate capability for sodium storage.

Galaxy Zoo: Observing secular evolution through bars

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cheung, Edmond; Faber, S. M.; Koo, David C.

In this paper, we use the Galaxy Zoo 2 data set to study the behavior of bars in disk galaxies as a function of specific star formation rate (SSFR) and bulge prominence. Our sample consists of 13,295 disk galaxies, with an overall (strong) bar fraction of 23.6% ± 0.4%, of which 1154 barred galaxies also have bar length (BL) measurements. These samples are the largest ever used to study the role of bars in galaxy evolution. We find that the likelihood of a galaxy hosting a bar is anticorrelated with SSFR, regardless of stellar mass or bulge prominence. We findmore » that the trends of bar likelihood and BL with bulge prominence are bimodal with SSFR. We interpret these observations using state-of-the-art simulations of bar evolution that include live halos and the effects of gas and star formation. We suggest our observed trends of bar likelihood with SSFR are driven by the gas fraction of the disks, a factor demonstrated to significantly retard both bar formation and evolution in models. We interpret the bimodal relationship between bulge prominence and bar properties as being due to the complicated effects of classical bulges and central mass concentrations on bar evolution and also to the growth of disky pseudobulges by bar evolution. These results represent empirical evidence for secular evolution driven by bars in disk galaxies. This work suggests that bars are not stagnant structures within disk galaxies but are a critical evolutionary driver of their host galaxies in the local universe (z < 1).« less

Acute muscular strength assessment using free weight bars of different thickness.

PubMed

Ratamess, Nicholas A; Faigenbaum, Avery D; Mangine, Gerald T; Hoffman, Jay R; Kang, Jie

2007-02-01

The purpose of the present investigation was to examine strength performance of 6 common resistance training exercises using free weight bars of different thickness. Eleven resistance-trained men (8.2 +/- 2.6 years of experience; age: 22.1 +/- 1.6 years; body mass: 90.5 +/- 8.9 kg) underwent 1 repetition maximum (1RM) strength testing on 6 occasions in random order for the deadlift, bent-over row, upright row, bench press, seated shoulder press, and arm curl exercises under 3 conditions using: (a) a standard Olympic bar (OL), (b) a 2-inch thick bar (5.08 cm grip span), and (c) a 3-inch thick bar (7.62 cm grip span). Significant (p < 0.05) interactions were observed for the "pulling" exercises. For the deadlift and bent-over row, highest 1RM values were obtained with OL, followed by the 2- and 3-inch bar. Significant 1RM performance decrements for the 2- and 3-inch bars were approximately 28.3 and 55.0%, respectively, for the deadlift; decrements for the 2- and 3-inch bars were approximately 8.9 and 37.3%, respectively, for the bent-over row. For the upright row and arm curl, similar 1RMs were obtained for OL and the 2-inch bar. However, a significant performance reduction was observed using the 3-inch bar (approximately 26.1% for the upright row and 17.6% for the arm curl). The reductions in 1RM loads correlated significantly to hand size and maximal isometric grip strength (r = -0.55 to -0.73). No differences were observed between bars for the bench press or shoulder press. In conclusion, the use of 2- and 3-inch thick bars may result in initial weight reductions primarily for pulling exercises presumably due to greater reliance on maximal grip strength and larger hand size.

Hydrothermal synthesis, characterization, and thermal properties of alumino silicate azide sodalite, Na8[AlSiO4]6(N3)2

NASA Astrophysics Data System (ADS)

Borhade, A. V.; Wakchaure, S. G.; Dholi, A. G.; Kshirsagar, T. A.

2017-07-01

First time we report the synthesis, structural characterization and thermal behavior of an unusual N3 - containing alumino-silicate sodalite mineral. Azide sodalite, Na8[AlSiO4]6(N3)2 has been synthesized under hydrothermal conditions at 433 K in steel lined Teflon autoclave. The structural and microstructural properties of azide sodalite mineral was characterized by various methods including FT-IR, XRD, SEM, TGA, and MAS NMR. Crystal structure have been refined by Rietveld method in P\\bar 43n space group, indicating that the N3 - sodalite has cubic in lattice. High temperature study was carried out to see the effect of thermal expansion on cell dimension ( a o) of azide sodalite. Thermal behavior of sodalite was also assessed by thermogravimetric method.

New double molybdate Na9Fe(MoO4)6: Synthesis, structure, properties

NASA Astrophysics Data System (ADS)

Savina, Aleksandra A.; Solodovnikov, Sergey F.; Basovich, Olga M.; Solodovnikova, Zoya A.; Belov, Dmitry A.; Pokholok, Konstantin V.; Gudkova, Irina A.; Stefanovich, Sergey Yu.; Lazoryak, Bogdan I.; Khaikina, Elena G.

2013-09-01

A new double molybdate Na9Fe(MoO4)6 was synthesized using solid state reactions and studied with X-ray powder diffraction, second harmonic generation (SHG) technique, differential scanning calorimetry, X-ray fluorescence analysis, Mössbauer and dielectric impedance spectroscopy. Single crystals of Na9Fe(MoO4)6 were obtained and its structure was solved (the space group R3¯, a=14.8264(2), c=19.2402(3) Å, V=3662.79(9) Å3, Z=6, R=0.0132). The structure is related to that of sodium ion conductor II-Na3Fe2(AsO4)3. The basic structure units are polyhedral clusters composed of central FeО6 octahedron sharing edges with three Na(1)О6 octahedra. The clusters share common vertices with bridging МоО4 tetrahedra to form an open 3D framework where the cavities are occupied by Na(2) and Na(3) atoms. The compound melts incongruently at 904.7±0.2 K. Arrhenius type temperature dependence of electric conductivity σ has been registered in solid state (σ=6.8×10-2 S сm-1 at 800 K), thus allowing considering Na9Fe(MoO4)6 as a new sodium ion conductor.

A thermodynamic model for the prediction of phase equilibria and speciation in the H 2O-CO 2-NaCl-CaCO 3-CaSO 4 system from 0 to 250 °C, 1 to 1000 bar with NaCl concentrations up to halite saturation

NASA Astrophysics Data System (ADS)

Li, Jun; Duan, Zhenhao

2011-08-01

A thermodynamic model is developed for the calculation of both phase and speciation equilibrium in the H 2O-CO 2-NaCl-CaCO 3-CaSO 4 system from 0 to 250 °C, and from 1 to 1000 bar with NaCl concentrations up to the saturation of halite. The vapor-liquid-solid (calcite, gypsum, anhydrite and halite) equilibrium together with the chemical equilibrium of H+,Na+,Ca, CaHCO3+,Ca(OH)+,OH-,Cl-, HCO3-,HSO4-,SO42-, CO32-,CO,CaCO and CaSO 4(aq) in the aqueous liquid phase as a function of temperature, pressure and salt concentrations can be calculated with accuracy close to the experimental results. Based on this model validated from experimental data, it can be seen that temperature, pressure and salinity all have significant effects on pH, alkalinity and speciations of aqueous solutions and on the solubility of calcite, halite, anhydrite and gypsum. The solubility of anhydrite and gypsum will decrease as temperature increases (e.g. the solubility will decrease by 90% from 360 K to 460 K). The increase of pressure may increase the solubility of sulphate minerals (e.g. gypsum solubility increases by about 20-40% from vapor pressure to 600 bar). Addition of NaCl to the solution may increase mineral solubility up to about 3 molality of NaCl, adding more NaCl beyond that may slightly decrease its solubility. Dissolved CO 2 in solution may decrease the solubility of minerals. The influence of dissolved calcite on the solubility of gypsum and anhydrite can be ignored, but dissolved gypsum or anhydrite has a big influence on the calcite solubility. Online calculation is made available on www.geochem-model.org/model.

Nanoscale modulations in (KLa)(CaW)O-6 and (NaLa)(CaW)O-6

DOE Office of Scientific and Technical Information (OSTI.GOV)

Licurse, Mark; Borisevich, Albina Y; Davies, Peter

2012-01-01

Complex nanoscale modulations are identified in two new A-site ordered perovskites, (KLa)(CaW)O{sub 6} and (NaLa)(CaW)O{sub 6}. In (KLa)(CaW)O{sub 6}, selected-area electron diffraction (SAED) and high-resolution transmission electron microscopy (HRTEM) show an incommensurate nanocheckerboard modulation with {approx}9.4 x 9.4 a{sub p} periodicity (a{sub p} {approx} 4 {angstrom} for the cubic perovskite aristotype). For (NaLa)(CaW)O{sub 6} a one-dimensional modulation is observed with a {approx}16(1 1 0)a{sub p} repeat; the <1 1 0> orientation of the nanostripes is different from the <1 0 0> stripes observed in other mixed A-site systems. Studies using high temperature x-ray diffraction suggest the formation of the complexmore » modulations is associated with small deviations from the ideal 1:1:1:1 stoichiometry of the (A{sup +}La{sup 3+})(CaW)O{sub 6} phases. Z-contrast images acquired on an aberration-corrected microscope provide evidence for deviations from stoichiometry with a {approx}1:15 periodic arrangement of La{sub 4/3}(CaW)O{sub 6}:(NaLa)(CaW)O{sub 6} nano-phases.« less

VizieR Online Data Catalog: 3.6um S4G Galactic bars characterization (Diaz-Garcia+, 2016)

NASA Astrophysics Data System (ADS)

Diaz-Garcia, S.; Salo, H.; Laurikainen, E.; Herrera-Endoqui, M.

2015-11-01

Here, we provide the bar strength measurements of a sample of ~600 barred galaxies drawn from the Spitzer Survey of Stellar Structure in Galaxies (Sheth et al., 2010, Cat. J/PASP/122/1397). Bars were identified based on the morphological classifications by Buta et al. (2015, Cat. J/ApJS/217/32). Besides, we provide a parameterization of the stellar contribution to the rotation curve and an estimate to the stellar-to-halo mass ratio within the optical radius for a sample of 1345 non-highly inclined galaxies (i<65°). The radial force profiles and rotation curve decomposition models of each of these galaxies are also given. Table A1 contains fundamental parameters of the galaxies such as the total stellar mass and distances (values for all the S4G sample are calculated in Munoz-Mateos et al., 2015ApJS..219....3M). Besides, we provide an estimate of the scale-heights and optical radii. We also list the inclination-corrected HI maximum velocities, the parameters of the stellar and halo components of the rotation curves, and the estimates of the halo-to-stellar mass ratios within the optical disk. In Table A2 it is given the gravitational torque parameters and radii, with and without spiral arms and halo correction. In Table A3 it is provided the maximum normalized Fourier amplitudes and radii (for the m = 2, 4, 6 and 8 components) and the bar ellipticities (from Herrera-Endoqui et al., 2015A&A...582A..86H) deprojected to the disk plane using the orientation parameters from S4G Pipeline 4 (Salo et al., 2015, Cat. J/ApJS/219/4). The evaluation of the gravitational torques and m=2 Fourier amplitude at the bar radius is also listed in both tables. In the directory "rfp" we provide the gravitational torque radial profiles, with and without spiral arms and halo correction, even Fourier amplitudes and m=2 phase of 1345 non-highly inclined disk S4G galaxies ("radialforce_profiles.dat"). Likewise, for the same sample, in the directory "rcdm" we tabulate the rotation curve

Automated multisyringe stir bar sorptive extraction using robust montmorillonite/epoxy-coated stir bars.

PubMed

Ghani, Milad; Saraji, Mohammad; Maya, Fernando; Cerdà, Víctor

2016-05-06

Herein we present a simple, rapid and low cost strategy for the preparation of robust stir bar coatings based on the combination of montmorillonite with epoxy resin. The composite stir bar was implemented in a novel automated multisyringe stir bar sorptive extraction system (MS-SBSE), and applied to the extraction of four chlorophenols (4-chlorophenol, 2,4-dichlorophenol, 2,4,6-trichlorophenol and pentachlorophenol) as model compounds, followed by high performance liquid chromatography-diode array detection. The different experimental parameters of the MS-SBSE, such as sample volume, selection of the desorption solvent, desorption volume, desorption time, sample solution pH, salt effect and extraction time were studied. Under the optimum conditions, the detection limits were between 0.02 and 0.34μgL(-1). Relative standard deviations (RSD) of the method for the analytes at 10μgL(-1) concentration level ranged from 3.5% to 4.1% (as intra-day RSD) and from 3.9% to 4.3% (as inter-day RSD at 50μgL(-1) concentration level). Batch-to-batch reproducibility for three different stir bars was 4.6-5.1%. The enrichment factors were between 30 and 49. In order to investigate the capability of the developed technique for real sample analysis, well water, wastewater and leachates from a solid waste treatment plant were satisfactorily analyzed. Copyright © 2016 Elsevier B.V. All rights reserved.

A novel approach to bar adsorptive microextraction: Cork as extractor phase for determination of benzophenone, triclocarban and parabens in aqueous samples.

PubMed

Dias, Adriana Neves; da Silva, Ana Cristine; Simão, Vanessa; Merib, Josias; Carasek, Eduardo

2015-08-12

This study describes the use of cork as a new coating for bar adsorptive microextraction (BAμE) and its application in determining benzophenone, triclocarban and parabens in aqueous samples by HPLC-DAD. In this study bars with 7.5 and 15 mm of length were used. The extraction and liquid desorption steps for BAμE were optimized employing multivariate and univariate procedures. The desorption time and solvent used for liquid desorption were optimized by univariate and multivariate studies, respectively. For the extraction step the sample pH was optimized by univariate experiments while the parameters extraction time and ionic strength were evaluated using the Doehlert design. The optimum extraction conditions were sample pH 5.5, NaCl concentration 25% and extraction time 90 min. Liquid desorption was carried out for 30 min with 250 μL (bar length of 15 mm) or 100 μL (bar length of 7.5 mm) of ACN:MeOH (50:50, v/v). The quantification limits varied between 1.6 and 20 μg L(-1) (bar length of 15 mm) and 0.64 and 8 μg L(-1) (bar length of 7.5 mm). The linear correlation coefficients were higher than 0.98 for both bars. The method with 7.5 mm bar length showed recovery values between 65 and 123%. The bar-to-bar reproducibility and the repeatability were lower than 13% (n = 2) and 14% (n = 3), respectively. Copyright © 2015 Elsevier B.V. All rights reserved.

Lattice dynamics of Cs2NaYbF6 and Cs2NaYF6 elpasolites: Ab initio calculation

NASA Astrophysics Data System (ADS)

Chernyshev, V. A.; Petrov, V. P.; Nikiforov, A. E.; Zakir'yanov, D. O.

2015-06-01

The ab initio calculations of the crystal structure and the phonon spectrum of Cs2NaYbF6 and Cs2NaYF6 crystals with the elpasolite structure have been performed. The frequencies and types of fundamental vibrations have been determined. The calculations have been performed in the framework of the density functional theory using the molecular orbital method with hybrid functionals in the CRYSTAL09 program developed for the simulation of periodic structures. The outer 5 s and 5 p shells of the rare-earth ion have been described in Gaussian-type basis sets. The influence of inner shells, including 4 f electron shells, on the outer shells has been described using the pseudopotential. It has been shown that this approach allows the description of the phonon spectrum with the inclusion of the splitting of the longitudinal and transverse optical modes.

Performance simulation of BaBar DIRC bar boxes in TORCH

NASA Astrophysics Data System (ADS)

Föhl, K.; Brook, N.; Castillo García, L.; Cussans, D.; Forty, R.; Frei, C.; Gao, R.; Gys, T.; Harnew, N.; Piedigrossi, D.; Rademacker, J.; Ros García, A.; van Dijk, M.

2017-12-01

TORCH is a large-area precision time-of-flight detector based on the DIRC principle. The DIRC bar boxes of the BaBar experiment at SLAC could possibly be reused to form a part of the TORCH detector time-of-flight wall area, proposed to provide positive particle identification of low momentum kaons in the LHCb experiment at CERN. For a potential integration of BaBar bar boxes into TORCH, new imaging readout optics are required. From the several designs of readout optics that have been considered, two are used in this paper to study the effect of BaBar bar optical imperfections on the detector reconstruction performance. The kaon-pion separation powers obtained from analysing simulated photon hit patterns show the performance reduction for a BaBar bar of non-square geometry compared to a perfectly rectangular cross section.

Hot press and roll welding of titanium-6-percent-aluminum-4-percent-vanadium bar and sheet with auto-vacuum cleaning

NASA Technical Reports Server (NTRS)

Holko, K. H.

1972-01-01

Hot press butt welds were made in 0.5 in. diameter bar, and roll lap welds were made in 0.060 in. thick sheet of Ti-6A1-4V. For hot press welds made after auto-vacuum cleaning at 1800 F for 2 hours, weld strength and ductility equaled the parent metal properties. Only 5 minutes of pressing time were needed at 1800 F and 200 psi to make the hot press welds. Roll welds were made in sheet at 1750 F with only 10 percent deformation. The welds in the bar and sheet were metallurgically indistinguishable from the parent material.

Co-intercalation of Mg(2+) and Na(+) in Na(0.69)Fe2(CN)6 as a High-Voltage Cathode for Magnesium Batteries.

PubMed

Kim, Dong-Min; Kim, Youngjin; Arumugam, Durairaj; Woo, Sang Won; Jo, Yong Nam; Park, Min-Sik; Kim, Young-Jun; Choi, Nam-Soon; Lee, Kyu Tae

2016-04-06

Thanks to the advantages of low cost and good safety, magnesium metal batteries get the limelight as substituent for lithium ion batteries. However, the energy density of state-of-the-art magnesium batteries is not high enough because of their low operating potential; thus, it is necessary to improve the energy density by developing new high-voltage cathode materials. In this study, nanosized Berlin green Fe2(CN)6 and Prussian blue Na(0.69)Fe2(CN)6 are compared as high-voltage cathode materials for magnesium batteries. Interestingly, while Mg(2+) ions cannot be intercalated in Fe2(CN)6, Na(0.69)Fe2(CN)6 shows reversible intercalation and deintercalation of Mg(2+) ions, although they have the same crystal structure except for the presence of Na(+) ions. This phenomenon is attributed to the fact that Mg(2+) ions are more stable in Na(+)-containing Na(0.69)Fe2(CN)6 than in Na(+)-free Fe2(CN)6, indicating Na(+) ions in Na(0.69)Fe2(CN)6 plays a crucial role in stabilizing Mg(2+) ions. Na(0.69)Fe2(CN)6 delivers reversible capacity of approximately 70 mA h g(-1) at 3.0 V vs Mg/Mg(2+) and shows stable cycle performance over 35 cycles. Therefore, Prussian blue analogues are promising structures for high-voltage cathode materials in Mg batteries. Furthermore, this co-intercalation effect suggests new avenues for the development of cathode materials in hybrid magnesium batteries that use both Mg(2+) and Na(+) ions as charge carriers.

Solubility of SC2O3 in NA3ALF6-K3ALF6-ALF3 Melts

NASA Astrophysics Data System (ADS)

Tian, Zhongliang; Hu, Xun; Lai, Yanqing; Yang, Shu; Ye, Shaolong; Li, Jie

The electrolyte with high solubility for Sc2O3 is very important to realize the preparation of Al-Sc master alloy by the molten salt electrolysis. The solubility of Sc2O3 in K3AlF6-Na3AlF6-AlF3 melts is determined with an isothermal saturation method. The effects of KR (ratio of K3AlF6 to K3AlF6+Na3AlF6), the concentration of Al2O3 and the temperature on the solubility of Sc2O3 are also investigated. The results indicate that the solubility of Sc2O3 in K3AlF6-Na3AlF6-AlF3 melts increases and then decreases with KR increasing. The solubility of Sc2O3 is 8.698 wt.% in (K3AlF6-Na3AlF6)(KR25%)-18 wt.%AlF3 melts at 940°C. The effect of temperature on the solubility is little, and the values are 8.575 wt.% and 8.762 wt.% respectively when the temperatures are 930°C and 960°C. The solubility decreases from 8.809 wt.% to 7.058 wt.% as the concentration of Al2O3 increases from 1.5 wt.% to 5.0 wt.% at 950°C.

Nanoscale modulations in (KLa)(CaW)O{sub 6} and (NaLa)(CaW)O{sub 6}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Licurse, Mark W., E-mail: mlicurse@seas.upenn.edu; Borisevich, Albina Y., E-mail: albinab@ornl.gov; Davies, Peter K., E-mail: davies@seas.upenn.edu

2012-07-15

Complex nanoscale modulations are identified in two new A-site ordered perovskites, (KLa)(CaW)O{sub 6} and (NaLa)(CaW)O{sub 6}. In (KLa)(CaW)O{sub 6}, selected-area electron diffraction (SAED) and high-resolution transmission electron microscopy (HRTEM) show an incommensurate nanocheckerboard modulation with {approx}9.4 Multiplication-Sign 9.4a{sub p} periodicity (a{sub p} Almost-Equal-To 4 A for the cubic perovskite aristotype). For (NaLa)(CaW)O{sub 6} a one-dimensional modulation is observed with a {approx}16(1 1 0)a{sub p} repeat; the Left-Pointing-Angle-Bracket 1 1 0 Right-Pointing-Angle-Bracket orientation of the nanostripes is different from the Left-Pointing-Angle-Bracket 1 0 0 Right-Pointing-Angle-Bracket stripes observed in other mixed A-site systems. Studies using high temperature x-ray diffraction suggest the formationmore » of the complex modulations is associated with small deviations from the ideal 1:1:1:1 stoichiometry of the (A{sup +}La{sup 3+})(CaW)O{sub 6} phases. Z-contrast images acquired on an aberration-corrected microscope provide evidence for deviations from stoichiometry with a {approx}1:15 periodic arrangement of La{sub 4/3}(CaW)O{sub 6}:(NaLa)(CaW)O{sub 6} nano-phases. - Graphical abstract: Complex nanoscale modulations are identified in two new A-site ordered perovskites, (KLa)(CaW)O{sub 6} and (NaLa)(CaW)O{sub 6}. In (KLa)(CaW)O{sub 6}, selected-area electron diffraction and high-resolution transmission electron microscopy show a two-dimensional, nanocheckerboard modulation. For (NaLa)(CaW)O{sub 6} a one-dimensional modulation is observed; the Left-Pointing-Angle-Bracket 1 1 0 Right-Pointing-Angle-Bracket orientation of the nanostripes is different from the Left-Pointing-Angle-Bracket 1 0 0 Right-Pointing-Angle-Bracket stripes observed in other mixed A-site systems. Highlights: Black-Right-Pointing-Pointer Two new A-site ordered perovskites were synthesized, (KLa)(CaW)O{sub 6} and (NaLa)(CaW)O{sub 6}. Black

Frustration by competing interactions in the highly-distorted double perovskites La2NaRuO6 and La2NaOsO6

NASA Astrophysics Data System (ADS)

Aczel, A. A.; Bugaris, D. E.; Li, L.; Yan, J.-Q.; de La Cruz, C.; Zur Loye, H.-C.; Nagler, S. E.

2013-03-01

The usual classical behavior of S = 3/2, B-site ordered double perovskites results in simple, commensurate magnetic ground states. In contrast, heat capacity and neutron powder diffraction measurements for the S = 3/2 systems La2NaB'O6 (B' = Ru, Os) reveal an incommensurate magnetic ground state for La2NaRuO6 and a drastically suppressed ordered moment for La2NaOsO6. This behavior is attributed to the large monoclinic structural distortions of these double perovskites. The distortions have the effect of weakening the nearest neighbor superexchange interactions, presumably to an energy scale that is comparable to the next nearest neighbor superexchange. The exotic ground states in these materials can then arise from a competition between these two types of antiferromagnetic interactions, providing a novel mechanism for achieving frustration in the double perovskite family. Work at ORNL is supported by the Division of Scientific User Facilities and the Materials Science and Engineering Division, DOE Basic Energy Sciences. Work at the University of South Carolina is supported by the Heterogeneous Functional Materials Research Center, funded by DOE under award number de-sc0001061.

Gaseous Structures in Barred Galaxies: Effects of the Bar Strength

NASA Astrophysics Data System (ADS)

Kim, Woong-Tae; Seo, Woo-Young; Kim, Yonghwi

2012-10-01

Using hydrodynamic simulations, we investigate the physical properties of gaseous substructures in barred galaxies and their relationships with the bar strength. The gaseous medium is assumed to be isothermal and unmagnetized. The bar potential is modeled as a Ferrers prolate with index n. To explore situations with differing bar strength, we vary the bar mass f bar relative to the spheroidal component as well as its aspect ratio { R}. We derive expressions as functions of f bar and { R} for the bar strength Qb and the radius r(Qb ) where the maximum bar torque occurs. When applied to observations, these expressions suggest that bars in real galaxies are most likely to have f bar ~ 0.25-0.50 and n <~ 1. Dust lanes approximately follow one of the x 1-orbits and tend to be straighter under a stronger and more elongated bar, but are insensitive to the presence of self-gravity. A nuclear ring of a conventional x 2 type forms only when the bar is not so massive or elongated. The radius of an x 2-type ring is generally smaller than the inner Lindblad resonance, decreases systematically with increasing Qb , and is slightly larger when self-gravity is included. This is evidence that the ring position is not determined by the resonance, but instead by the amount of angular momentum loss at dust-lane shocks. Nuclear spirals exist only when the ring is of the x 2 type and is sufficiently large in size. Unlike the other features, nuclear spirals are transient in that they start out being tightly wound and weak, and then, due to the nonlinear effect, unwind and become stronger until they turn into shocks, with an unwinding rate that is higher for larger Qb . The mass inflow rate to the galaxy center is found to be less than 0.01 M ⊙ yr-1 for models with Qb <~ 0.2, while becoming larger than 0.1 M ⊙ yr-1 when Qb >~ 0.2 and self-gravity is included.

Effects of the Bar Strength of Gaseous Features in Barred Galaxies

NASA Astrophysics Data System (ADS)

Kim, Woong-Tae; Seo, W.; Kim, Y.

2013-01-01

Barred galaxies commonly possess gaseous structures such as a pair of dust lanes, a nuclear ring, and nuclear spirals at their centers. We use hydrodynamic simulations to study the physical properties of the gaseous structures in barred galaxies and their relationships with the bar strength. We vary the bar mass fbar relative to the spheroidal component as well as its aspect ratio. We derive expressions for the bar strength Qb and the radius where the maximum bar torque occurs. When applied to observations, these expressions suggest that bars in real galaxies are most likely to have fbar = 0.25-0.5. Dust lanes approximately follow one of x1-orbits and tend to be more straight under a stronger and more elongated bar. A nuclear ring of a conventional x2 type forms only when the bar is not so massive or elongated. The radius of an x2-type ring is generally smaller than the inner Lindblad resonance, decreases systematically with increasing Qb, evidencing that the ring position is not determined by the resonance but by the bar strength. Nuclear spirals exist only when the ring is of the x2-type and sufficiently large in size. Unlike the other features, nuclear spirals are transient in that they start out as being tightly-wound and weak, and then due to the nonlinear effect unwind and become stronger until turning into shocks, with an unwinding rate higher for larger Qb. These results suggest that the bar strength is the primary factor that determine the properties of gaseous structures in barred galaxies.

Comparing the physiological and perceptual responses of construction workers (bar benders and bar fixers) in a hot environment.

PubMed

Wong, Del Pui-Lam; Chung, Joanne Wai-Yee; Chan, Albert Ping-Chuen; Wong, Francis Kwan-Wah; Yi, Wen

2014-11-01

This study aimed to (1) quantify the respective physical workloads of bar bending and fixing; and (2) compare the physiological and perceptual responses between bar benders and bar fixers. Field studies were conducted during the summer in Hong Kong from July 2011 to August 2011 over six construction sites. Synchronized physiological, perceptual, and environmental parameters were measured from construction rebar workers. The average duration of the 39 field measurements was 151.1 ± 22.4 min under hot environment (WBGT = 31.4 ± 2.2 °C), during which physiological, perceptual and environmental parameters were synchronized. Energy expenditure of overall rebar work, bar bending, and bar fixing were 2.57, 2.26 and 2.67 Kcal/min (179, 158 and 186 W), respectively. Bar fixing induced significantly higher physiological responses in heart rate (113.6 vs. 102.3 beat/min, p < 0.05), oxygen consumption (9.53 vs. 7.14 ml/min/kg, p < 0.05), and energy expenditure (2.67 vs. 2.26 Kcal/min, p < 0.05) (186 vs. 158 W, p < 0.05) as compared to bar bending. Perceptual response was higher in bar fixing but such difference was not statistically significant. Findings of this study enable the calculation of daily energy expenditure of rebar work. Copyright © 2014 Elsevier Ltd and The Ergonomics Society. All rights reserved.

The crystal structure of synthetic simmonsite, Na 2LiAlF 6

NASA Astrophysics Data System (ADS)

Ross, Kirk C.; Mitchell, Roger H.; Chakhmouradian, Anton R.

2003-04-01

The structure of the synthetic fluoroperovskite, Na 2LiAlF 6 (simmonsite), has been determined by powder X-ray diffraction using the Rietveld method of structure refinement. The compound adopts space group P2 1/ n [#14; a=5.2842(1); b=5.3698(1); c=7.5063(2) Å; β=89.98(1)°; Z=4), and is a member of the cryolite (Na 2NaAlF 6) structural group characterized by ordering of the B-site cations (Li, Al) and tilting of the BF 6 octahedra according to the tilt scheme a-b-c+. Rotations of the B-site polyhedra are less ( ΦLi=14.9°; ΦAl=17.0°) than those found in cryolite ( ΦNa=18.6; ΦAl=23.5°) because of the larger difference in the ionic radii of the B-site cations in cryolite as compared to those in simmonsite. Na at the A-site is displaced from the special position resulting in 10- and 8-fold coordination in simmonsite and cryolite, respectively. By analogy with the synthetic compound, naturally occurring simmonsite is considered to adopt space group P2 1/ n (#14) and not the P2 1(#4) or P2 1/ m(#11) space groups.

Equilibrium, Kinetics, and Spectroscopic Studies of SF6 Hydrate in NaCl Electrolyte Solution.

PubMed

Seo, Youngrok; Moon, Donghyun; Lee, Changho; Park, Jeong-Woo; Kim, Byeong-Soo; Lee, Gang-Woo; Dotel, Pratik; Lee, Jong-Won; Cha, Minjun; Yoon, Ji-Ho

2015-05-19

Many studies have focused on desalination via hydrate formation; however, for their potential application, knowledge pertaining to thermodynamic stability, formation kinetics, and guest occupation behavior in clathrate hydrates needs to be determined. Herein, the phase equilibria of SF6 hydrates in the presence of NaCl solutions (0, 2, 4, and 10 wt %) were monitored in the temperature range of 277-286 K and under pressures of up to 1.4 MPa. The formation kinetics of SF6 hydrates in the presence of NaCl solutions (0, 2, and 4 wt %) was also investigated. Gas consumption curves of SF6 hydrates showed that a pure SF6 hydrate system allowed fast hydrate growth as well as high conversion yield, whereas SF6 hydrate in the presence of NaCl solutions showed retarded hydrate growth rate as well as low conversion yield. In addition, structural identification of SF6 hydrates with and without NaCl solutions was performed using spectroscopic tools such as Raman spectroscopy and X-ray diffraction. The Raman spectrometer was also used to evaluate the temperature-dependent release behavior of guest molecules in SF6 and SF6 + 4 wt % NaCl hydrates. The results indicate that whereas SF6 hydrate starts to decompose at around 240 K, the escape of SF6 molecules in SF6 + 4 wt % NaCl hydrate is initiated rapidly at around 205 K. The results of this study can provide a better understanding of guest-host interaction in electrolyte-containing systems.

An investigation of the tri-bar gripping system on isometric muscular endurance.

PubMed

Drury, Daniel G; Faggiono, Heath; Stuempfle, Kristin J

2004-11-01

Recently, a new product called the Tri-Bar has been introduced as an alternative to the standard round weightlifting bar. The Tri-Bar has the same weight, length, and circumference as a standard weightlifting bar and differs only in that the shape of the bar is formed like a triangle with rounded edges. Theoretically, the shape of the bar will enhance gripping comfort and increase muscular endurance. We studied 32 moderately trained males who were free from upper-body injury or limitation. Each participant completed 4 visits to the lab as part of 2 separate investigations. The first investigation was a comparison of straight-arm hang times while grasping a standard Olympic bar or a Tri-Bar attached to the top of a power rack. The second investigation involved grasping a standard revolving cable handle or a Tri-Bar revolving handle attached to a weight equal to half the subject's body weight. In both investigations, time was used as a measure of isometric muscular endurance. Differences were determined using a dependent t-test, and a level of significance was set at p < 0.05. Mean hang times were significantly longer when the men hung from the Tri-Bar (107.6 seconds) versus the standard bar (95.4 seconds) (p = 0.015). Conversely, in the investigation using the revolving handles, the round bar produced longer grasping times (71.5 seconds) than the Tri-Bar (62.6 seconds) (p = 0.000). The results of this investigation indicate that a fixed and stable Tri-Bar may help to increase hang time, but a Tri-Bar free to rotate within the grasp may decrease grasping time in comparison to a standard round handle. With regard to exercises that require isometric grasping, the Tri-Bar may be an effective alternative to the standard bar for increasing isometric grasping endurance.

First Principles Investigation of the Geometrical and Electrochemical Properties of Na4P6 and Li4P2S6

NASA Astrophysics Data System (ADS)

Rush, Larry E., Jr.; Holzwarth, N. A. W.

First principles simulations are used to examine the structural and physical properties of Na4P2S6 in comparison with its Li4P2S6 analog. Four model structures are considered including the C 2 / m structure recently reported by Kuhn and co-workers from their analysis of single crystals of Na4P2S6, and three structures related to the P63 / mcm structure with P site disorder found in 1982 by Mercier and co-workers from their analysis of single crystals of Li4P2S6. The computational results indicate that both Na4P2S6 and Li4P2S6 have the same disordered ground state structures consistent with the P63 / mcm space group, while the optimized C 2 / m structures have higher energies by 0.1 eV and 0.4 eV per formula unit for Na4P2S6 and Li4P2S6, respectively. Simulations of ion migration suggest that Na4P2S6 may have more favorable ionic conductivity compared to Li4P2S6. Supported by NSF Grant DMR-1105485 and DMR-1507942.

The role of chest radiography following pectus bar removal.

PubMed

Farach, Sandra M; Danielson, Paul D; Chandler, Nicole M

2016-07-01

Surgical correction of pectus excavatum (PE) via a minimally invasive approach involves placement of a steel bar, which is subsequently removed. The purpose of our study was to evaluate the incidence of pneumothorax and the role for chest radiography (CXR) in patients undergoing pectus bar removal. A retrospective review of 84 patients who underwent pectus bar removal from 2006 to 2014 was performed. Results of postoperative CXR, repeat imaging, need for chest thoracostomy tube placement, and complications were analyzed. Mean Haller index prior to correction was 4.3 ± 0.9. The mean time between PE repair and bar removal was 2.3 ± 0.6 years. Sixty-one patients (72.6 %) had a postoperative CXR. Thirty-one (50.8 %) had no acute findings, 20 (32.8 %) had findings of atelectasis or subcutaneous emphysema, and 10 (16.4 %) had a pneumothorax. One patient (1.6 %) had a second postoperative CXR for a small pneumothorax and rib fractures. There were two complications (2.4 %). No chest tubes were placed for pneumothorax, and 95 % of patients were discharged the day of surgery. Postoperative CXR following pectus bar removal is unnecessary given the low incidence of postoperative pneumothorax requiring intervention. Patients can be safely discharged the day of surgery without the need for routine postoperative chest imaging.

The Carnegie-Irvine Galaxy Survey. V. Statistical Study of Bars and Buckled Bars

NASA Astrophysics Data System (ADS)

Li, Zhao-Yu; Ho, Luis C.; Barth, Aaron J.

2017-08-01

Simulations have shown that bars are subject to a vertical buckling instability that transforms thin bars into boxy or peanut-shaped structures, but the physical conditions necessary for buckling to occur are not fully understood. We use the large sample of local disk galaxies in the Carnegie-Irvine Galaxy Survey to examine the incidence of bars and buckled bars across the Hubble sequence. Depending on the disk inclination angle (I), a buckled bar reveals itself as either a boxy/peanut-shaped bulge (at high I) or as a barlens structure (at low I). We visually identify bars, boxy/peanut-shaped bulges, and barlenses, and examine the dependence of bar and buckled bar fractions on host galaxy properties, including Hubble type, stellar mass, color, and gas mass fraction. We find that the barred and unbarred disks show similar distributions in these physical parameters. The bar fraction is higher (70%-80%) in late-type disks with low stellar mass (M * < 1010.5 M ⊙) and high gas mass ratio. In contrast, the buckled bar fraction increases to 80% toward massive and early-type disks (M * > 1010.5 M ⊙), and decreases with higher gas mass ratio. These results suggest that bars are more difficult to grow in massive disks that are dynamically hotter than low-mass disks. However, once a bar forms, it can easily buckle in the massive disks, where a deeper potential can sustain the vertical resonant orbits. We also find a probable buckling bar candidate (ESO 506-G004) that could provide further clues to understand the timescale of the buckling process.

Enabling Narrow(est) IWA Coronagraphy with STIS BAR5 and BAR10 Occulters

NASA Astrophysics Data System (ADS)

Schneider, Glenn; Gaspar, Andras; Debes, John; Gull, Theodore; Hines, Dean; Apai, Daniel; Rieke, George

2017-09-01

The Space Telescope Imaging Spectrograph's (STIS) BAR5 coronagraphic occulter was designed to provide high-contrast, visible-light, imaging in close (> 0.15") angular proximity to bright point-sources. We explored and verified the functionality and utility of the BAR5 occulter. We also investigated, and herein report on, the use of the BAR10 rounded corners as narrow-angle occulters and compare IWA vs. contrast performance for the BAR5, BAR10, and Wedge occulters. With that, we provide recommendations for the most efficacious BAR5 and BAR10 use on-orbit in support of GO science.

Phase relations in the system NaCl-KCl-H2O II: Differential thermal analysis of the halite liquidus in the NaCl-H2O binary above 450°c

USGS Publications Warehouse

Gunter, W.D.; Chou, I.-Ming; Girsperger, Sven

1983-01-01

The solubility of halite can be expressed as a function of the mole-fractional-based activity of NaCl in the liquid phase (L) in temperature (T, °K) and pressure (P, bars) In  Our liquidus data (based on 10 compositions) above 500 bars for these brines were combined with this equation to generate activity coefficients of NaCl which were fit within their experimental uncertainties to the following one parameter Margules equation In . Concentrated solutions of NaCl show negative deviations from ideality which rapidly increase in magnitude with decreasing XNaCl.

Bar Evolution and Bar Properties from Disc Galaxies in the Early Universe

NASA Astrophysics Data System (ADS)

Hutchinson-Smith, Tenley; Simmons, Brooke

2017-01-01

Bars in disc galaxies indicate a large collection of stars in a specific configuration of orbits that give the galaxy center a rectangular looking feature. Astronomers have discovered that these bars affect the distribution of matter in galaxies, and are also related to galaxy stellar mass and star formation history. Little is known about the specifics of how bars evolve and drive the evolution of their host galaxies because only a handful of bars have been studied in detail so far. I have examined a sample of 8,221 barred galaxies from the early universe to identify and examine correlations with galaxy properties. The data comes from Galaxy Zoo, an online citizen science project that allows anyone to classify and measure detailed properties of galaxies. I present results including the fraction of galaxies in the sample that have bars, and the variation of galaxy properties with bar length, including galaxy color and stellar mass. I also compare these results to barred galaxies in the local universe. I will discuss the implications of these results in the context of galaxy evolution overall, including the effect of dark matter on bars and galaxy evolution.

Prototype Stop Bar System Evaluation at John F. Kennedy International Airport

DTIC Science & Technology

1992-09-01

2 Red Stop Bar Visual Presentation 4 3 Green Stop Bar Visual Presentation 5 4 Photographs of Red and Green Inset Stop Bar Lights 6 5 Photographs of...to green. This provides pilots with a visual confirmation of the controller’s verbal clearance and is intended to prevent runway incursions. The Port...34 colocated with the red lights. The visual presentation of an individual stop bar appears as either five red lights (see figure 2), or five green

The Carnegie-Irvine Galaxy Survey. V. Statistical Study of Bars and Buckled Bars

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Zhao-Yu; Ho, Luis C.; Barth, Aaron J., E-mail: lizy@shao.ac.cn

Simulations have shown that bars are subject to a vertical buckling instability that transforms thin bars into boxy or peanut-shaped structures, but the physical conditions necessary for buckling to occur are not fully understood. We use the large sample of local disk galaxies in the Carnegie-Irvine Galaxy Survey to examine the incidence of bars and buckled bars across the Hubble sequence. Depending on the disk inclination angle ( i ), a buckled bar reveals itself as either a boxy/peanut-shaped bulge (at high i ) or as a barlens structure (at low i ). We visually identify bars, boxy/peanut-shaped bulges, andmore » barlenses, and examine the dependence of bar and buckled bar fractions on host galaxy properties, including Hubble type, stellar mass, color, and gas mass fraction. We find that the barred and unbarred disks show similar distributions in these physical parameters. The bar fraction is higher (70%–80%) in late-type disks with low stellar mass ( M {sub *} < 10{sup 10.5} M {sub ⊙}) and high gas mass ratio. In contrast, the buckled bar fraction increases to 80% toward massive and early-type disks ( M {sub *} > 10{sup 10.5} M {sub ⊙}), and decreases with higher gas mass ratio. These results suggest that bars are more difficult to grow in massive disks that are dynamically hotter than low-mass disks. However, once a bar forms, it can easily buckle in the massive disks, where a deeper potential can sustain the vertical resonant orbits. We also find a probable buckling bar candidate (ESO 506−G004) that could provide further clues to understand the timescale of the buckling process.« less

Magnetical hollow fiber bar collection of extract in homogenous ionic liquid microextraction of triazine herbicides in water samples.

PubMed

Wang, Kun; Jiang, Jia; Kang, Mingqin; Li, Dan; Zang, Shuang; Tian, Sizhu; Zhang, Hanqi; Yu, Aimin; Zhang, Ziwei

2017-04-01

The homogeneous ionic liquid microextraction combined with magnetical hollow fiber bar collection was developed for extracting triazine herbicides from water samples. These analytes were separated and determined by high performance liquid chromatography. The triazines were quickly extracted into ionic liquid microdroplets dispersed in solution, and then these microdroplets were completely collected with magnetical hollow fiber bars; the pores of which were impregnated with hydrophobic ionic liquid, which makes the phase separation simplified with no need of centrifugation. Some experimental parameters, such as the type of ionic liquid, ultrasonic immersion time of hollow fiber, pH of sample solution, volume of hydrophilic ionic liquid, amount of ion-pairing agent NH 4 PF 6 , NaCl concentration, number of magnetical hollow fiber bar, stirring rate, and collection time were investigated and optimized. When the present method was applied to the analysis of real water samples, the precision and recoveries of six triazine herbicides vary from 0.1 to 9.2% and 73.4 to 118.5%, respectively. The detection limits for terbumeton, ametryn, prometryn, terbutryn, trietazine, and dimethametryn were 0.48, 0.15, 0.15, 0.14, 0.35, and 0.16 μg L -1 , respectively.

Structural, optical, and magnetic properties of Na{sub 8}Eu{sub 2}(Si{sub 2}S{sub 6}){sub 2} and Na{sub 8}Eu{sub 2}(Ge{sub 2}S{sub 6}){sub 2}: Europium(II) quaternary chalcogenides that contain an ethane-like (Si{sub 2}S{sub 6}){sup 6−} or (Ge{sub 2}S{sub 6}){sup 6−} moiety

DOE Office of Scientific and Technical Information (OSTI.GOV)

Choudhury, Amitava, E-mail: choudhurya@mst.edu; Ghosh, Kartik; Grandjean, Fernande

2015-03-15

Two isostructural europium(II) quaternary chalcogenides, Na{sub 8}Eu{sub 2}(Si{sub 2}S{sub 6}){sub 2}, 1, and Na{sub 8}Eu{sub 2}(Ge{sub 2}S{sub 6}){sub 2}, 2, containing an ethane-like (Si{sub 2}S{sub 6}){sup 6−} or (Ge{sub 2}S{sub 6}){sup 6−} moiety have been synthesized by employing the polychalcogenide molten flux method. Single-crystal X-ray diffraction reveals that both compounds crystallize in the C2/m space group, and their structures contain layers of ([Na{sub 2}Eu{sub 2}(Si{sub 2}S{sub 6}){sub 2}]{sup 6−}){sub ∞} or ([Na{sub 2}Eu{sub 2}(Ge{sub 2}S{sub 6}){sub 2}]{sup 6−}){sub ∞} anions held together by six interlayer sodium cations to yield (Na{sub 6}[Na{sub 2}Eu{sub 2}(Si{sub 2}S{sub 6}){sub 2}]){sub ∞} and (Na{sub 6}[Na{submore » 2}Eu{sub 2}(Ge{sub 2}S{sub 6}){sub 2}]){sub ∞}. Compound 2 is a semiconductor with an optical band gap of 2.15(2) eV. The temperature dependence of the magnetic susceptibility indicates that compounds 1 and 2 are paramagnetic with μ{sub eff}=7.794(1) μ{sub B} per Eu and g=1.964(1) for 1 and μ{sub eff}=8.016(1) μ{sub B} per Eu and g=2.020(1) for 2, moments that are in good agreement with the europium(II) spin-only moment of 7.94 μ{sub B}. The europium-151 Mössbauer isomer shift of 2 confirms the presence of europium(II) cations with an electronic configuration between [Xe]4f{sup 6.81} and 4f{sup 7}6s{sup 0.32}. - Graphical abstract: TOC figure caption: structure of Na{sub 8}Eu{sub 2}(Si{sub 2}S{sub 6}){sub 2} viewed along the a-axis showing the filling of A–B and B–A types of anion layers with two different types of cations. - Highlights: • Synthesis of quaternary europium chalcogenides containing ethane-like dimer. • Structural characterization employing single-crystal X-ray diffraction. • Mössbauer spectroscopy and magnetic measurements confirm presence of Eu(II)« less

Studying W‧ boson contributions in \\bar{B} \\rightarrow {D}^{(* )}{{\\ell }}^{-}{\\bar{\

NASA Astrophysics Data System (ADS)

Wang, Yi-Long; Wei, Bin; Sheng, Jin-Huan; Wang, Ru-Min; Yang, Ya-Dong

2018-05-01

Recently, the Belle collaboration reported the first measurement of the τ lepton polarization P τ (D*) in \\bar{B}\\to {D}* {τ }-{\\bar{ν }}τ decay and a new measurement of the rate of the branching ratios R(D*), which are consistent with the Standard Model (SM) predictions. These could be used to constrain the New Physics (NP) beyond the SM. In this paper, we probe \\bar{B}\\to {D}(* ){{\\ell }}-{\\bar{ν }}{\\ell } (ℓ = e, μ, τ) decays in the model-independent way and in the specific G(221) models with lepton flavour universality. Considering the theoretical uncertainties and the experimental errors at the 95% C.L., we obtain the quite strong bounds on the model-independent parameters {C}{{LL}}{\\prime },{C}{{LR}}{\\prime },{C}{{RR}}{\\prime },{C}{{RL}}{\\prime },{g}V,{g}A,{g}V{\\prime },{g}A{\\prime } and the specific G(221) model parameter rates. We find that the constrained NP couplings have no obvious effects on all (differential) branching ratios and their rates, nevertheless, many NP couplings have very large effects on the lepton spin asymmetries of \\bar{B}\\to {D}(* ){{\\ell }}-{\\bar{ν }}{\\ell } decays and the forward–backward asymmetries of \\bar{B}\\to {D}* {{\\ell }}-{\\bar{ν }}{\\ell }. So we expect precision measurements of these observables would be researched by LHCb and Belle-II.

Phase behavior of gemini surfactant hexylene-1,6-bis(dodecyldimethylammonium bromide) and polyelectrolyte NaPAA.

PubMed

Pi, Yingying; Shang, Yazhuo; Peng, Changjun; Liu, Honglai; Hu, Ying; Jiang, Jianwen

2006-07-01

The phase behavior of aqueous mixtures of gemini surfactant hexylene-1,6-bis(dodecyldimethylammonium bromide) (12-6-12) and oppositely charged polyelectrolyte sodium polyacrylate (NaPAA) has been studied experimentally. Compared to the mixtures of the traditional surfactant dodecyltrimethylammonium bromide (DTAB) and NaPAA, the gel phase region in the 12-6-12/NaPAA solution is larger. Element analysis reveals that NaPAA in the gel phase tends to replace the counterions of surfactant micelle and to release its own counterions. Spherical aggregates are observed in either top or bottom gel phase as detected by transmission electron microscopy. The addition of sodium bromide (NaBr) leads to a decrease in the gel phase region and the occurrence of a new cream phase.

[Amaranth bars enriched with fructans: acceptability and nutritional value].

PubMed

Dias Capriles, Vanessa; Gomes Arêas, José Alfredo

2010-09-01

There is an increasing appeal for convenience foods with potential health benefits to the consumer. Raw materials with high nutritional value and functional properties must be used on the development of these food products. Amaranth is a gluten-free grain with high nutrition value. Inulin and oligofructose are prebiotic ingredients presenting effects as the enhancement of calcium absorption. Amaranth bars enriched with inulin and oligofructose were developed in the flavors: banana, Brazilian nuts and dried grape, coconut, peach, strawberry and wall nut. The proximate composition were determined and compared to commercial cereal bars, available in traditional (n=59), light (n=60), diet (n=8), with soy (n=10) and quinoa (n=1) categories. Amaranth bars present mean global acceptance values from 6.3 to 7.6 on a 9-point hedonic scale, nutritional advantages as compared to commercial cereal bars (caloric reduction and higher levels of dietary fiber). Although amaranth is an unknown raw material in Brazil, it shows good potential to be used in the manufacturing of ready-to-eat products. As they are gluten free, these amaranth bars are also an alternative product for celiacs, also contributing to the enhancement of calcium absorption, a problem frequently observed in these patients.

Reduced expression of Na(v)1.6 sodium channels and compensation by Na(v)1.2 channels in mice heterozygous for a null mutation in Scn8a.

PubMed

Vega, Ana V; Henry, Diane L; Matthews, Gary

2008-09-05

The voltage-gated sodium channel alpha subunit Na(v)1.6, encoded by the Scn8a gene, accumulates at high density at mature nodes of Ranvier of myelinated axons, replacing the Na(v)1.2 channels found at nodes earlier in development. To investigate this preferential expression of Na(v)1.6 at adult nodes, we examined isoform-specific expression of sodium channels in mice heterozygous for a null mutation in Scn8a. Immunoblots from these +/- mice had 50% of the wild-type level of Na(v)1.6 protein, and their optic-nerve nodes of Ranvier had correspondingly less anti-Na(v)1.6 immunofluorescence. Protein level and nodal immunofluorescence of the Na(v)1.2 alpha subunit increased in Scn8a(+/-) mice, keeping total sodium channel expression approximately constant despite partial loss of Na(v)1.6 channels. The results are consistent with a model in which Na(v)1.6 and Na(v)1.2 compete for binding partners at sites of high channel density, such as nodes of Ranvier. We suggest that Na(v)1.6 channels normally occupy most of the molecular machinery responsible for channel clustering because they have higher binding affinity, and not because they are exclusively recognized by mechanisms for transport and insertion of sodium channels in myelinated axons. The reduced amount of Na(v)1.6 protein in Scn8a(+/-) mice is apparently insufficient to saturate the nodal binding sites, allowing Na(v)1.2 channels to compete more successfully.

Chloride-induced corrosion mechanism and rate of enamel- and epoxy-coated deformed steel bars embedded in mortar

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tang, Fujian; Chen, Genda; Brow, Richard K.

The chloride-induced corrosion mechanisms of uncoated, pure enamel (PE)-coated, mixed enamel (ME)-coated, double enamel (DE)-coated, and fusion bonded epoxy (FBE)-coated deformed steel bars embedded in mortar cylinders are investigated in 3.5 wt.% NaCl solution and compared through electrochemical tests and visual inspection. Corrosion initiated after 29 or 61 days of tests in all uncoated and enamel-coated steel bars, and after 244 days of tests in some FBE-coated steel bars. In active stage, DE- and FBE-coated steel bars are subjected to the highest and lowest corrosion rates, respectively. The uncoated and ME-coated steel bars revealed relatively uniform corrosion while the PE-,more » DE-, and FBE-coated steel bars experienced pitting corrosion around damaged coating areas. Due to the combined effect of ion diffusion and capillary suction, wet–dry cyclic immersion caused more severe corrosion than continuous immersion. Both exposure conditions affected the corrosion rate more significantly than the water–cement ratio in mortar design.« less

Bar Code Labels

NASA Technical Reports Server (NTRS)

1988-01-01

American Bar Codes, Inc. developed special bar code labels for inventory control of space shuttle parts and other space system components. ABC labels are made in a company-developed anodizing aluminum process and consecutively marketed with bar code symbology and human readable numbers. They offer extreme abrasion resistance and indefinite resistance to ultraviolet radiation, capable of withstanding 700 degree temperatures without deterioration and up to 1400 degrees with special designs. They offer high resistance to salt spray, cleaning fluids and mild acids. ABC is now producing these bar code labels commercially or industrial customers who also need labels to resist harsh environments.

Fatigue Behavior of Glass Fiber-Reinforced Polymer Bars after Elevated Temperatures Exposure.

PubMed

Li, Guanghui; Zhao, Jun; Wang, Zike

2018-06-16

Fiber-reinforced polymer (FRP) bars have been widely applied in civil engineering. This paper presents the results of an experimental study to investigate the tensile fatigue mechanical properties of glass fiber-reinforced polymer (GFRP) bars after elevated temperatures exposure. For this purpose, a total of 105 GFRP bars were conducted for testing. The specimens were exposed to heating regimes of 100, 150, 200, 250, 300 and 350 °C for a period of 0, 1 or 2 h. The GFRP bars were tested with different times of cyclic load after elevated temperatures exposure. The results show that the tensile strength and elastic modulus of GFRP bars decrease with the increase of elevated temperature and holding time, and the tensile strength of GFRP bars decreases obviously by 19.5% when the temperature reaches 250 °C. Within the test temperature range, the tensile strength of GFRP bars decreases at most by 28.0%. The cyclic load accelerates the degradation of GFRP bars after elevated temperature exposure. The coupling of elevated temperature and holding time enhance the degradation effect of cyclic load on GFRP bars. The tensile strength of GFRP bars after elevated temperatures exposure at 350 °C under cyclic load is reduced by 50.5% compared with that at room temperature and by 36.3% compared with that after exposing at 350 °C without cyclic load. In addition, the elastic modulus of GFRP bars after elevated temperatures exposure at 350 °C under cyclic load is reduced by 17.6% compared with that at room temperature and by 6.0% compared with that after exposing at 350 °C without cyclic load.

Martian Meanders and Scroll-Bars

NASA Image and Video Library

2017-03-01

This is a portion of an inverted fluvial channel in the region of Aeolis/Zephyria Plana, at the Martian equator. Channels become inverted when the sediments filling them become more resistant to erosion than the surrounding material. Here, the most likely process leading to hardening of the channel material is chemical cementation by precipitation of minerals. Once the surrounding material erodes, the channel is left standing as a ridge. The series of curvilinear lineations are ancient scroll-bars, which are features typical of river meanders (bends) in terrestrial fluvial channels. Scroll-bars are series of ridges that result from the continuous lateral migration of a meander. On Earth, they are more common in mature rivers. The presence of scroll bars suggests that the water flow in this channel may have been sustained for a relatively long time. Measuring characteristics of these scroll-bars and meanders may help to estimate the amount of water that once flowed in this channel, aiding our understanding of the history of water on Mars. The map is projected here at a scale of 25 centimeters (9.8 inches) per pixel. [The original image scale is 29.3 centimeters (11.5 inches) per pixel (with 1 x 1 binning); objects on the order of 88 centimeters (29.6 inches) across are resolved.] North is up. http://photojournal.jpl.nasa.gov/catalog/PIA21551

THE MASS PROFILE AND SHAPE OF BARS IN THE SPITZER SURVEY OF STELLAR STRUCTURE IN GALAXIES (S{sup 4}G): SEARCH FOR AN AGE INDICATOR FOR BARS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Taehyun; Lee, Myung Gyoon; Sheth, Kartik

2015-01-20

We have measured the radial light profiles and global shapes of bars using two-dimensional 3.6 μm image decompositions for 144 face-on barred galaxies from the Spitzer Survey of Stellar Structure in Galaxies. The bar surface brightness profile is correlated with the stellar mass and bulge-to-total (B/T) ratio of their host galaxies. Bars in massive and bulge-dominated galaxies (B/T > 0.2) show a flat profile, while bars in less massive, disk-dominated galaxies (B/T ∼ 0) show an exponential, disk-like profile with a wider spread in the radial profile than in the bulge-dominated galaxies. The global two-dimensional shapes of bars, however, are rectangular/boxy, independentmore » of the bulge or disk properties. We speculate that because bars are formed out of disks, bars initially have an exponential (disk-like) profile that evolves over time, trapping more disk stars to boxy bar orbits. This leads bars to become stronger and have flatter profiles. The narrow spread of bar radial profiles in more massive disks suggests that these bars formed earlier (z > 1), while the disk-like profiles and a larger spread in the radial profile in less massive systems imply a later and more gradual evolution, consistent with the cosmological evolution of bars inferred from observational studies. Therefore, we expect that the flatness of the bar profile can be used as a dynamical age indicator of the bar to measure the time elapsed since the bar formation. We argue that cosmic gas accretion is required to explain our results on bar profile and the presence of gas within the bar region.« less

Bar-spheroid interaction in galaxies

NASA Technical Reports Server (NTRS)

Hernquist, Lars; Weinberg, Martin D.

1992-01-01

N-body simulation and linear analysis is employed to investigate the secular evolution of barred galaxies, with emphasis on the interaction between bars and spheroidal components of galaxies. This interaction is argued to drive secular transfer of angular momentum from bars to spheroids, primarily through resonant coupling. A moderately strong bar, having mass within corotation about 0.3 times the enclosed spheroid mass, is predicted to shed all its angular momentum typically in less than about 10 exp 9 yr. Even shorter depletion time scales are found for relatively more massive bars. It is suggested either that spheroids around barred galaxies are structured so as to inhibit strong coupling with bars, or that bars can form by unknown processes long after disks are established. The present models reinforce the notion that bars can drive secular evolution in galaxies.

Numerical modeling of the autumnal thermal bar

NASA Astrophysics Data System (ADS)

Tsydenov, Bair O.

2018-03-01

The autumnal riverine thermal bar of Kamloops Lake has been simulated using atmospheric data from December 1, 2015, to January 4, 2016. The nonhydrostatic 2.5D mathematical model developed takes into account the diurnal variability of the heat fluxes and wind on the lake surface. The average values for shortwave and longwave radiation and latent and sensible heat fluxes were 19.7 W/m2, - 95.9 W/m2, - 11.8 W/m2, and - 32.0 W/m2 respectively. Analysis of the wind regime data showed prevailing easterly winds and maximum speed of 11 m/s on the 8th and 19th days. Numerical experiments with different boundary conditions at the lake surface were conducted to evaluate effects of variable heat flux and wind stress. The results of modeling demonstrated that the variable heat flux affects the process of thermal bar evolution, especially during the lengthy night cooling. However, the wind had the greatest impact on the behavior of the autumnal thermal bar: The easterly winds contributed to an earlier appearance of the thermal bar, but the strong winds generating the intensive circulations (the velocity of the upper lake flow increased to 6 cm/s) may destroy the thermal bar front.

Finite Element Analysis of IPS Empress II Ceramic Bridge Reinforced by Zirconia Bar

PubMed Central

Kermanshah, H.; Bitaraf, T.; Geramy, A.

2012-01-01

Objective: The aim of this study was to determine the effect of trenched zirconia bar on the von Mises stress distribution of IPS –Empress II core ceramics. Materials and Methods: The three-dimensional model including a three-unit bridge from the second premolar to the second molar was designed. The model was reinforced with zirconia bar (ZB), zirconia bar with vertical trench (VZB) and zirconia bar with horizontal trench (HZB) (cross sections of these bars were circular). The model without zirconia bar was designed as the control. The bridges were loaded by 200 N and 500 N on the occlusal surface at the middle of the pontic component and von Mises stresses were evaluated along a defined path. Results: In the connector area, von Mises stress in MPa were approximately identical in the specimens with ZB (at molar connector (MC): 4.75 and at premolar connector (PC): 6.40) and without ZB (MC: 5.50, PC: 6.68), and considerable differences were not recognized. Whereas, Von-Mises stress (MPa) in the specimens with horizontal trenched Zirconia bar (HZB) (MC: 3.91, PC: 2.44) and Vertical trenched Zirconia bar (VZB) (MC: 2.53, PC: 2.56) was decreased considerably. Conclusion: Embeded trenched zirconia bar could reinforce IPS-Empress II at the connector area which is a main failure region in all ceramic fixed partial dentures. PMID:23323181

Finite Element Analysis of IPS Empress II Ceramic Bridge Reinforced by Zirconia Bar.

PubMed

Kermanshah, H; Bitaraf, T; Geramy, A

2012-01-01

The aim of this study was to determine the effect of trenched zirconia bar on the von Mises stress distribution of IPS -Empress II core ceramics. The three-dimensional model including a three-unit bridge from the second premolar to the second molar was designed. The model was reinforced with zirconia bar (ZB), zirconia bar with vertical trench (VZB) and zirconia bar with horizontal trench (HZB) (cross sections of these bars were circular). The model without zirconia bar was designed as the control. The bridges were loaded by 200 N and 500 N on the occlusal surface at the middle of the pontic component and von Mises stresses were evaluated along a defined path. IN THE CONNECTOR AREA, VON MISES STRESS IN MPA WERE APPROXIMATELY IDENTICAL IN THE SPECIMENS WITH ZB (AT MOLAR CONNECTOR (MC): 4.75 and at premolar connector (PC): 6.40) and without ZB (MC: 5.50, PC: 6.68), and considerable differences were not recognized. Whereas, Von-Mises stress (MPa) in the specimens with horizontal trenched Zirconia bar (HZB) (MC: 3.91, PC: 2.44) and Vertical trenched Zirconia bar (VZB) (MC: 2.53, PC: 2.56) was decreased considerably. Embeded trenched zirconia bar could reinforce IPS-Empress II at the connector area which is a main failure region in all ceramic fixed partial dentures.

Triple bar, high efficiency mechanical sealer

DOEpatents

Pak, Donald J.; Hawkins, Samantha A.; Young, John E.

2013-03-19

A clamp with a bottom clamp bar that has a planar upper surface is provided. The clamp may also include a top clamp bar connected to the bottom clamp bar, and a pressure distribution bar between the top clamp bar and the bottom clamp bar. The pressure distribution bar may have a planar lower surface in facing relation to the upper surface of the bottom clamp bar. An object is capable of being disposed in a clamping region between the upper surface and the lower surface. The width of the planar lower surface may be less than the width of the upper surface within the clamping region. Also, the pressure distribution bar may be capable of being urged away from the top clamp bar and towards the bottom clamp bar.

Barring intervention? Lesbian and gay bars as an underutilized venue for tobacco interventions.

PubMed

Leibel, Katherine; Lee, Joseph G L; Goldstein, Adam O; Ranney, Leah M

2011-07-01

Lesbian, gay, bisexual, and transgender (LGBT) communities are at high risk for tobacco use. While LGBT communities have historically considered bars to be safe places to socialize and congregate, these spaces are often tobacco-friendly environments and may have potential as sites for much needed intervention. Only a few public health interventions have attempted to work through bars and clubs to decrease tobacco use in the LGBT populations. Evidence from HIV prevention suggests some potential interventions in bars, and the tobacco industry has worked extensively (and successfully) to utilize bars in marketing efforts. Lesbian and gay bars are underutilized in tobacco control, suggesting missed avenues for chronic disease prevention programs. Researchers and communities should continue to recognize the importance of clean indoor air laws covering bars and develop additional strategies for reaching LGBT populations with disparities.

Effect of bar-code technology on the safety of medication administration.

PubMed

Poon, Eric G; Keohane, Carol A; Yoon, Catherine S; Ditmore, Matthew; Bane, Anne; Levtzion-Korach, Osnat; Moniz, Thomas; Rothschild, Jeffrey M; Kachalia, Allen B; Hayes, Judy; Churchill, William W; Lipsitz, Stuart; Whittemore, Anthony D; Bates, David W; Gandhi, Tejal K

2010-05-06

Serious medication errors are common in hospitals and often occur during order transcription or administration of medication. To help prevent such errors, technology has been developed to verify medications by incorporating bar-code verification technology within an electronic medication-administration system (bar-code eMAR). We conducted a before-and-after, quasi-experimental study in an academic medical center that was implementing the bar-code eMAR. We assessed rates of errors in order transcription and medication administration on units before and after implementation of the bar-code eMAR. Errors that involved early or late administration of medications were classified as timing errors and all others as nontiming errors. Two clinicians reviewed the errors to determine their potential to harm patients and classified those that could be harmful as potential adverse drug events. We observed 14,041 medication administrations and reviewed 3082 order transcriptions. Observers noted 776 nontiming errors in medication administration on units that did not use the bar-code eMAR (an 11.5% error rate) versus 495 such errors on units that did use it (a 6.8% error rate)--a 41.4% relative reduction in errors (P<0.001). The rate of potential adverse drug events (other than those associated with timing errors) fell from 3.1% without the use of the bar-code eMAR to 1.6% with its use, representing a 50.8% relative reduction (P<0.001). The rate of timing errors in medication administration fell by 27.3% (P<0.001), but the rate of potential adverse drug events associated with timing errors did not change significantly. Transcription errors occurred at a rate of 6.1% on units that did not use the bar-code eMAR but were completely eliminated on units that did use it. Use of the bar-code eMAR substantially reduced the rate of errors in order transcription and in medication administration as well as potential adverse drug events, although it did not eliminate such errors. Our data show

Diffusion and the dynamics of displacive phase transitions in cryolite (Na3AlF6) and chiolite (Na5Al3F14): Multi-nuclear NMR studies

NASA Astrophysics Data System (ADS)

Spearing, Dane R.; Stebbins, Jonathan F.; Farnan, Ian

1994-10-01

Cryolite is a mixed-cation perovskite (Na2(NaAl)F6) which undergoes a monoclinic to orthorhombic displacive phase transition at ˜550° C. Chiolite (Na5Al3F14) is associated with cryolite in natural deposits, and consists of sheets of corner sharing [AlF6] octahedra interlayered with edge-sharing [NaF6] octahedra. Multi-nuclear NMR line shape and relaxation time (T1) studies were performed on cryolite and chiolite in order to gain a better understanding of the atomic motions associated with the phase transition in cryolite, and Na diffusion in cryolite and chiolite. 27Al, 23Na, and 19F static NMR spectra and T1's in cryolite suggest that oscillatory motions of the [AlF6] octahedra among four micro-twin and anti-phase domains in α-cryolite begin at least 150° C below the transition temperature and persist above it. Variable temperature 23Na MAS NMR further indicates diffusional exchange at a rate of at least 13 kHz between the Na sites by the time the transition temperature is reached. 27Al and 23Na T1's show the same behavior with increasing temperature, indicating the same relaxation mechanisms are responsible for both. The first order nature of the cryolite transition is apparent as a jump in the 23Na and 27Al T1's. Above the transition temperature, the T1's decrease slightly indicating that the motions responsible for the drop in T1, are still present above the transition, further supporting the dynamic nature of the high temperature phase of cryolite. Chiolite 23Na static spectra decrease in linewidth with increasing temperature, indicating increased Na diffusion, which is interpreted as occurring within the [NaF6] sheets in the chiolite structure, but not between the two different Na sites. 27Al and 23Na T1's show similar behavior as in cryolite, but there is no discontinuity due to a phase transition. 19F T1's are constant from room temperature to 150° C indicating no oscillatory motion of the [AlF6] octahedra in chiolite.

NASICON-related Na3.4Mn0.4Fe1.6(PO4)3

PubMed Central

Yatskin, Michael M.; Strutynska, Nataliya Yu.; Baumer, Vyacheslav N.; Ogorodnyk, Ivan V.; Slobodyanik, Nikolay S.

2012-01-01

The solid solution, sodium [iron(III)/manganese(II)] tris­(orthophosphate), Na3.4Mn0.4Fe1.6(PO4)3, was obtained using a flux method. Its crystal structure is related to that of NASICON-type compounds. The [(Mn/Fe)2(PO4)3] framework is built up from an (Mn/Fe)O6 octa­hedron (site symmetry 3.), with a mixed Mn/Fe occupancy, and a PO4 tetra­hedron (site symmetry .2). The Na+ cations are distributed over two partially occupied sites in the cavities of the framework. One Na+ cation (site symmetry -3.) is surrounded by six O atoms, whereas the other Na+ cation (site symmetry .2) is surrounded by eight O atoms. PMID:22807697

Ultrasound-Guided Bar Edge Labeling in the Perioperative Assessment of Nuss Bar Removal.

PubMed

Incerti, Filippo; Bertocchini, Alessia; Ghionzoli, Marco; Messineo, Antonio

2017-12-01

Nuss bar removal after minimally invasive repair of pectus excavatum in patients where bar ends are not palpable, can be a challenging procedure for the surgeon; a blind dissection toward the bar edges may lead to intercostal vessels or deep intercostal muscle injuries. In this article, we describe a fast, repeatable, low-cost technique to detect bar edge and stabilizers. A perioperative scan is performed by means of a portable ultrasonograph a few minutes before the operation. The bar edge stabilizer is detected as a hyperechogenic image with a concentric crescent while the bar edge is detected as a hyperechogenic dashed line with net edges. The scan is performed, and the actual projection on the skin of the metal plaque bulk is then labeled on the patient's chest by an ink marker. We believe that this method may improve morbidity, operative time, and consequently, hospitalization length and costs.

The pterygoalar bar: A meta-analysis of its prevalence, morphology and morphometry.

PubMed

Pękala, Przemysław A; Henry, Brandon Michael; Pękala, Jakub R; Frączek, Paulina A; Taterra, Dominik; Natsis, Konstantinos; Piagkou, Maria; Skrzat, Janusz; Tomaszewska, Iwona M

2017-09-01

The pterygoalar (PA) bar is a bony bridge resulting from the partial or complete ossification of a PA ligament. The aim of this meta-analysis was to systematically analyze and provide the most comprehensive data on the prevalence, morphology and topographical anatomy of the PA bar. A comprehensive search of the major electronic databases (PubMed, Embase, ScienceDirect, SciELO, BIOSIS, and Web of Science) was conducted in order to identify relevant studies. Studies reporting the prevalence, side of occurrence, gender dimorphism and morphometry of the PA bar were included in the current study. A total of 25 articles (n = 16,168 subjects) were included in the meta-analysis. The overall pooled prevalence of the complete PA bar was 4.4% (95% CI: 3.0-6.0) and of the incomplete was 8.4% (95% CI: 4.6-13.3). The PA bar was most often observed unilaterally, on the left side. Analysis of geographical subgroups revealed considerable differences, with the lowest prevalence rates in Europe for both incomplete and complete PA bars. Considering the prevalence and anatomical characteristics of the PA bar, caution is recommended while planning or performing transfacial needle approach to the foramen ovale and when considering a differential diagnosis for nerve compression or entrapment syndromes. Copyright © 2017 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

Interference of Nonstandard Interactions with Standard Model in {B^0} \\to {π ^0}\\bar vv, B_c^ - \\to {D^ - }\\bar vv and \\bar B_s^0 \\to {K^0}\\bar vv Decays

NASA Astrophysics Data System (ADS)

Mahmood, Shakeel; Tahir, Farida; Mir, Azeem

2018-05-01

We study the contributions of nonstandard neutrino interactions (NSI) to the rare decays of pseudoscalar mesons involving neutrinos in the final state {B^0} \\to {π ^0}\\bar vv, B_c^ - \\to {D^ - }\\bar vv and \\bar B_s^0 \\to {\\bar K^0}\\bar vv, It is pointed that dominant contribution comes from the interference between standard model and nonstandard interaction We predict limits on NSIs free parameter ɛ uL ττ and compare them with experimental data. We further compare our results with perturbative QCD (pQCD) and QCD results for these reactions.

Pleistocene barrier bar seaward of ooid shoal complex near Miami, Florida

USGS Publications Warehouse

Halley, Robert B.; Shinn, Eugene A.; Hudson, J. Harold; Lidz, Barbara H.

1977-01-01

An ooid sand barrier bar of Pleistocene age was deposited along the seaward side of an ooid shoal complex southwest of Miami, Florida. The bar is 35 km long, about 0.8 km wide, elongate parallel with the trend of the ooid shoal complex and perpendicular to channels between individual shoals. A depression 1.6 km wide, interpreted as a back-barrier channel, isolates the bar from the ooid shoals. During sea-level fall and subaerial exposure of the bar, the ooid sand was cemented in place, preventing migration of the barrier. No Holocene analogue of this sand body is recognized, perhaps because of the relative youthfulness of Holocene ooid shoals. This Pleistocene ooid shoal complex, with its reservoir-size barrier bar, may serve as a refined model for exploration in ancient ooid sand belts.

Stem cells. m6A mRNA methylation facilitates resolution of naïve pluripotency toward differentiation.

PubMed

Geula, Shay; Moshitch-Moshkovitz, Sharon; Dominissini, Dan; Mansour, Abed AlFatah; Kol, Nitzan; Salmon-Divon, Mali; Hershkovitz, Vera; Peer, Eyal; Mor, Nofar; Manor, Yair S; Ben-Haim, Moshe Shay; Eyal, Eran; Yunger, Sharon; Pinto, Yishay; Jaitin, Diego Adhemar; Viukov, Sergey; Rais, Yoach; Krupalnik, Vladislav; Chomsky, Elad; Zerbib, Mirie; Maza, Itay; Rechavi, Yoav; Massarwa, Rada; Hanna, Suhair; Amit, Ido; Levanon, Erez Y; Amariglio, Ninette; Stern-Ginossar, Noam; Novershtern, Noa; Rechavi, Gideon; Hanna, Jacob H

2015-02-27

Naïve and primed pluripotent states retain distinct molecular properties, yet limited knowledge exists on how their state transitions are regulated. Here, we identify Mettl3, an N(6)-methyladenosine (m(6)A) transferase, as a regulator for terminating murine naïve pluripotency. Mettl3 knockout preimplantation epiblasts and naïve embryonic stem cells are depleted for m(6)A in mRNAs, yet are viable. However, they fail to adequately terminate their naïve state and, subsequently, undergo aberrant and restricted lineage priming at the postimplantation stage, which leads to early embryonic lethality. m(6)A predominantly and directly reduces mRNA stability, including that of key naïve pluripotency-promoting transcripts. This study highlights a critical role for an mRNA epigenetic modification in vivo and identifies regulatory modules that functionally influence naïve and primed pluripotency in an opposing manner. Copyright © 2015, American Association for the Advancement of Science.

Coffee straw can replace Hader bar for bar retained overdentures--a clinical report.

PubMed

Guttal, S S; Shetty, U S

2012-12-01

Bar attachment system provides retention and support for the overdenture. Retention of a mandibular denture can be achieved by an implant-retained or natural tooth-retained bar and stud attachment in the anterior segment of the mandible. A simple and cost effective treatment for more complex implant overdenture is the concept of conventional tooth-retained overdentures. The authors present a clinical report of a patient treated with a mandibular tooth-borne overdenture with a bar. The bar was fabricated using a coffee straw.

Dynamic analysis of four bar planar mechanism extended to six-bar planar mechanism with variable topology

NASA Astrophysics Data System (ADS)

Belleri, Basayya K.; Kerur, Shravankumar B.

2018-04-01

A computer-oriented procedure for solving the dynamic force analysis problem for general planar mechanisms is presented. This paper provides position analysis, velocity analysis, acceleration analysis and force analysis of six bar mechanism with variable topology approach. Six bar mechanism is constructed by joining two simple four bar mechanisms. Initially the position, velocity and acceleration analysis of first four bar mechanism are determined by using the input parameters. The outputs (angular displacement, velocity and acceleration of rocker)of first four bar mechanism are used as input parameter for the second four bar mechanism and the position, velocity, acceleration and forces are analyzed. With out-put parameters of second four-bar mechanism the force analysis of first four-bar mechanism is carried out.

$${{\\bar{d}} - {\\bar{u}}}$$ Flavor Asymmetry in the Proton in Chiral Effective Field Theory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Salamu, Y.; Ji, Cheung-Ryong; Melnitchouk, Wally

2015-09-01

Themore » $${\\bar d - \\bar u}$$ flavor asymmetry in the proton arising from pion loops is computed using chiral effective field theory. calculation includes both nucleon and Δ intermediate states, and uses both the fully relativistic and heavy baryon frameworks. x dependence of $${\\bar d - \\bar u}$$ extracted from the Fermilab E866 Drell–Yan data can be well reproduced in terms of a single transverse momentum cutoff parameter regulating the ultraviolet behavior of the loop integrals. In addition to the distribution at x > 0, corrections to the integrated asymmetry from zero momentum contributions are computed, which arise from pion rainbow and bubble diagrams at x = 0. These have not been accounted for in previous analyses, and can make important contributions to the lowest moment of $${\\bar d-\\bar u}$$ .« less

Cryogenic ultra-high power infrared diode laser bars

NASA Astrophysics Data System (ADS)

Crump, Paul; Frevert, C.; Hösler, H.; Bugge, F.; Knigge, S.; Pittroff, W.; Erbert, G.; Tränkle, G.

2014-02-01

GaAs-based high power diode lasers are the most efficient source of optical energy, and are in wide use in industrial applications, either directly or as pump sources for other laser media. Increased output power per laser is required to enable new applications (increased optical power density) and to reduce cost (more output per component leads to lower cost in $/W). For example, laser bars in the 9xx nm wavelength range with the very highest power and efficiency are needed as pump sources for many high-energy-class solid-state laser systems. We here present latest performance progress using a novel design approach that leverages operation at temperatures below 0°C for increases in bar power and efficiency. We show experimentally that operation at -55°C increases conversion efficiency and suppresses thermal rollover, enabling peak quasi-continuous wave bar powers of Pout > 1.6 kW to be achieved (1.2 ms, 10 Hz), limited by the available current. The conversion efficiency at 1.6 kW is 53%. Following on from this demonstration work, the key open challenge is to develop designs that deliver higher efficiencies, targeting > 80% at 1.6 kW. We present an analysis of the limiting factors and show that low electrical resistance is crucial, meaning that long resonators and high fill factor are needed. We review also progress in epitaxial design developments that leverage low temperatures to enable both low resistance and high optical performance. Latest results will be presented, summarizing the impact on bar performance and options for further improvements to efficiency will also be reviewed.

Narrow linewidth operation of a spectral beam combined diode laser bar.

PubMed

Zhu, Zhanda; Jiang, Menghua; Cheng, Siqi; Hui, Yongling; Lei, Hong; Li, Qiang

2016-04-20

Our experiment is expected to provide an approach for realizing ultranarrow linewidth for a spectral beam combined diode laser bar. The beams of a diode laser bar are combined in a fast axis after a beam transformation system. With the help of relay optics and a transform lens with a long focal length of 1.5 m, the whole wavelength of a spectral combined laser bar can be narrowed down to 0.48 nm from more than 10 nm. We have achieved 56.7 W cw from a 19-element single bar with an M² of 1.4  (in horizontal direction)×11.6  (in vertical direction). These parameters are good evidence that all the beams from the diode laser bar are combined together to increase the brightness.

Pectus bar removal: surgical technique and strategy to avoid complications.

PubMed

Park, Hyung Joo; Kim, Kyung Soo

2016-01-01

Pectus bar removal is the final stage of the procedure for minimally invasive repair of pectus excavatum. Based on our experience with one of the largest scale data, we would like to address the important issues in pectus bar removal, such as appropriate duration of bar maintenance, techniques for bar removal, and strategies to avoid complications. Between September 1999 and August 2015, we operated on 2,553 patients with pectus excavatum and carinatum using pectus bars for a minimally invasive approach. Among them, 1,821 patients (71.3%) underwent pectus bar removal as a final stage of pectus deformity repair, and their data were analyzed retrospectively to identify the outcomes and adverse effects of the pectus bar removal procedure. The mean age of the patients was 9.13 years (range, 16 months to 44 years) and the male to female ratio was 3.55. The study is approved by the Institutional Review Board (IRB), the ethical committee of Seoul St. Mary's Hospital. The IRB has exempted the informed consent from every patient in this study due to this is a retrospective chart review without revealing any patients' personal data. Our technique involved straightening of the bar in a supine position. The overall mean duration of pectus bar maintenance was 2.57 years (range, 4 months to 14 years). The mean duration was 2.02 years (range, 4 months to 7 years) for children under 12 years, 2.99 years (range, 7 months to 9 years) for teenagers aged 12-20 years, and 3.53 years (range, 3 months to 14 years) for adults over 20 years. Forty-eight patients (2.6%) underwent bar removal more than 5 years after bar insertion and 58 patients (3.2%) underwent bar removal earlier than initially planned. The most common adverse reaction after bar removal was wound seroma including infection (43 patients, 2.36%). Recurrence after bar removal occurred in nine patients (0.49%), and seven of these required redo repair (0.38%). Pectus bar removal is a safe and straightforward procedure with a

HCN(1-0) enhancement in the bar of NGC 2903

NASA Astrophysics Data System (ADS)

Leon, S.; Jeyakumar, S.; Pérez-Ramírez, D.; Verdes-Montenegro, L.; Lee, S. W.; Ocaña Flaquer, B.

2008-12-01

We have mapped the HCN(1-0) emission from two spiral galaxies, NGC 2903 and NGC 3504 to study the gas properties in the bars. The HCN(1-0) emission is detected in the center and along the bar of NGC 2903. The line ratio HCN(1-0)/ 12CO(1-0) ranges from 0.07 to 0.12 with the lowest value in the center. The enhancement of HCN(1-0) emission along the bar indicates a higher fraction of dense molecular gas in the bar than at the center. The mass of dense molecular gas in the center (2.2 × 107 M⊙) is about 6 times lower than that in the bar (1.2 × 108 M⊙). The total star formation rate (SFR) is estimated to be 1.4 M⊙ yr-1, where the SFR at the center is 1.9 times higher than that in the bar. The time scale of consumption of the dense molecular gas in the center is about ~ 3 × 107 yr which is much shorter than that in the bar of about 2 to 10 × 108 yr. The dynamical time scale of inflow of the gas from the bar to the center is shorter than the consumption time scale in the bar, which suggests that the star formation (SF) activity at the center is not deprived of fuel. In the bar, the fraction of dense molecular gas mass relative to the total molecular gas mass is twice as high along the leading edge than along the central axis of the bar. The HCN(1-0) emission has a large velocity dispersion in the bar, which can be attributed partially to the streaming motions indicative of shocks along the bar. In NGC 3504, the HCN(1-0) emission is detected only at the center. The fraction of dense molecular gas mass in the center is about 15%. Comparison of the SFR with the predictions from numerical simulations suggest that NGC 2903 harbors a young type B bar with a strong inflow of gas toward the center whereas NGC 3504 has an older bar and has already passed the phase of inflow of gas toward the center.

Pectus bar removal: surgical technique and strategy to avoid complications

PubMed Central

Kim, Kyung Soo

2016-01-01

Background Pectus bar removal is the final stage of the procedure for minimally invasive repair of pectus excavatum. Based on our experience with one of the largest scale data, we would like to address the important issues in pectus bar removal, such as appropriate duration of bar maintenance, techniques for bar removal, and strategies to avoid complications. Methods Between September 1999 and August 2015, we operated on 2,553 patients with pectus excavatum and carinatum using pectus bars for a minimally invasive approach. Among them, 1,821 patients (71.3%) underwent pectus bar removal as a final stage of pectus deformity repair, and their data were analyzed retrospectively to identify the outcomes and adverse effects of the pectus bar removal procedure. The mean age of the patients was 9.13 years (range, 16 months to 44 years) and the male to female ratio was 3.55. The study is approved by the Institutional Review Board (IRB), the ethical committee of Seoul St. Mary’s Hospital. The IRB has exempted the informed consent from every patient in this study due to this is a retrospective chart review without revealing any patients’ personal data. Results Our technique involved straightening of the bar in a supine position. The overall mean duration of pectus bar maintenance was 2.57 years (range, 4 months to 14 years). The mean duration was 2.02 years (range, 4 months to 7 years) for children under 12 years, 2.99 years (range, 7 months to 9 years) for teenagers aged 12–20 years, and 3.53 years (range, 3 months to 14 years) for adults over 20 years. Forty-eight patients (2.6%) underwent bar removal more than 5 years after bar insertion and 58 patients (3.2%) underwent bar removal earlier than initially planned. The most common adverse reaction after bar removal was wound seroma including infection (43 patients, 2.36%). Recurrence after bar removal occurred in nine patients (0.49%), and seven of these required redo repair (0.38%). Conclusions Pectus bar removal is a

Wine glass size and wine sales: a replication study in two bars.

PubMed

Pechey, Rachel; Couturier, Dominique-Laurent; Hollands, Gareth J; Mantzari, Eleni; Zupan, Zorana; Marteau, Theresa M

2017-08-01

Wine glass size may influence perceived volume and subsequently purchasing and consumption. Using a larger glass to serve the same portions of wine was found to increase wine sales by 9.4% (95% CI 1.9, 17.5) in a recent study conducted in one bar. The current study aimed to replicate this previous work in two other bars using a wider range of glass sizes. To match the previous study, a repeated multiple treatment reversal design, during which wine was served in glasses of the same design but different sizes, was used. The study was conducted in two bars in Cambridge, England, using glass sizes of 300, 370, 510 ml (Bar 1) and 300 and 510 ml (Bar 2). Customers purchased their choice of a 750 ml bottle, or standard UK measures of 125, 175 or 250 ml of wine, each of which was served with the same glass. Bar 1 Daily wine volume (ml) purchased was 10.5% (95% CI 1.0, 20.9) higher when sold in 510 ml compared to 370 ml glasses; but sales were not significantly higher with 370 ml versus 300 ml glasses (6.5%, 95% CI -5.2, 19.6). Bar 2 Findings were inconclusive as to whether daily wine purchased differed when using 510 ml versus 300 ml glasses (-1.1%, 95% CI -12.6, 11.9). These results provide a partial replication of previous work showing that introducing larger glasses (without manipulating portion size) increases purchasing. Understanding the mechanisms by which wine glass size influences consumption may elucidate when the effect can be expected and when not. Trial registration This study is a replication study, based on the procedure set out in the trial registration for the study that it attempts to replicate (ISRCTN registry: ISRCTN12018175).

Measurement of the forward-backward asymmetry of $$\\Lambda$$ and $$\\bar{\\Lambda}$$ production in $$p \\bar{p}$$ collisions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abazov, Victor Mukhamedovich

Here, we studymore » $$\\Lambda$$ and $$\\bar{\\Lambda}$$ production asymmetries in $$p \\bar{p} \\rightarrow \\Lambda (\\bar{\\Lambda}) X$$, $$p \\bar{p} \\rightarrow J/\\psi \\Lambda (\\bar{\\Lambda}) X$$, and $$p \\bar{p} \\rightarrow \\mu^\\pm \\Lambda (\\bar{\\Lambda}) X$$ events recorded by the D0 detector at the Fermilab Tevatron collider at $$\\sqrt{s} = 1.96$$ TeV. We find an excess of $$\\Lambda$$'s ($$\\bar{\\Lambda}$$'s) produced in the proton (antiproton) direction. This forward-backward asymmetry is measured as a function of rapidity. We confirm that the $$\\bar{\\Lambda}/\\Lambda$$ production ratio, measured by several experiments with various targets and a wide range of energies, is a universal function of "rapidity loss", i.e., the rapidity difference of the beam proton and the lambda.« less

Measurement of the forward-backward asymmetry of $$\\Lambda$$ and $$\\bar{\\Lambda}$$ production in $$p \\bar{p}$$ collisions

DOE PAGES

Abazov, Victor Mukhamedovich

2016-02-09

Here, we studymore » $$\\Lambda$$ and $$\\bar{\\Lambda}$$ production asymmetries in $$p \\bar{p} \\rightarrow \\Lambda (\\bar{\\Lambda}) X$$, $$p \\bar{p} \\rightarrow J/\\psi \\Lambda (\\bar{\\Lambda}) X$$, and $$p \\bar{p} \\rightarrow \\mu^\\pm \\Lambda (\\bar{\\Lambda}) X$$ events recorded by the D0 detector at the Fermilab Tevatron collider at $$\\sqrt{s} = 1.96$$ TeV. We find an excess of $$\\Lambda$$'s ($$\\bar{\\Lambda}$$'s) produced in the proton (antiproton) direction. This forward-backward asymmetry is measured as a function of rapidity. We confirm that the $$\\bar{\\Lambda}/\\Lambda$$ production ratio, measured by several experiments with various targets and a wide range of energies, is a universal function of "rapidity loss", i.e., the rapidity difference of the beam proton and the lambda.« less

What makes the family of barred disc galaxies so rich: damping stellar bars in spinning haloes

NASA Astrophysics Data System (ADS)

Collier, Angela; Shlosman, Isaac; Heller, Clayton

2018-05-01

We model and analyse the secular evolution of stellar bars in spinning dark matter (DM) haloes with the cosmological spin λ ˜ 0-0.09. Using high-resolution stellar and DM numerical simulations, we focus on angular momentum exchange between stellar discs and DM haloes of various axisymmetric shapes - spherical, oblate, and prolate. We find that stellar bars experience a diverse evolution that is guided by the ability of parent haloes to absorb angular momentum, J, lost by the disc through the action of gravitational torques, resonant and non-resonant. We confirm that dynamical bar instability is accelerated via resonant J-transfer to the halo. Our main findings relate to the long-term secular evolution of disc-halo systems: with an increasing λ, bars experience less growth and basically dissolve after they pass through vertical buckling instability. Specifically, with increasing λ, (1) the vertical buckling instability in stellar bars colludes with inability of the inner halo to absorb J - this emerges as the main factor weakening or destroying bars in spinning haloes; (2) bars lose progressively less J, and their pattern speeds level off; (3) bars are smaller, and for λ ≳ 0.06 cease their growth completely following buckling; (4) bars in λ > 0.03 haloes have ratio of corotation-to-bar radii, RCR/Rb > 2, and represent so-called slow bars without offset dust lanes. We provide a quantitative analysis of J-transfer in disc-halo systems, and explain the reasons for absence of growth in fast spinning haloes and its observational corollaries. We conclude that stellar bar evolution is substantially more complex than anticipated, and bars are not as resilient as has been considered so far.

Non-specific activities of the major herbicide-resistance gene BAR.

PubMed

Christ, Bastien; Hochstrasser, Ramon; Guyer, Luzia; Francisco, Rita; Aubry, Sylvain; Hörtensteiner, Stefan; Weng, Jing-Ke

2017-12-01

Bialaphos resistance (BAR) and phosphinothricin acetyltransferase (PAT) genes, which convey resistance to the broad-spectrum herbicide phosphinothricin (also known as glufosinate) via N-acetylation, have been globally used in basic plant research and genetically engineered crops 1-4 . Although early in vitro enzyme assays showed that recombinant BAR and PAT exhibit substrate preference toward phosphinothricin over the 20 proteinogenic amino acids 1 , indirect effects of BAR-containing transgenes in planta, including modified amino acid levels, have been seen but without the identification of their direct causes 5,6 . Combining metabolomics, plant genetics and biochemical approaches, we show that transgenic BAR indeed converts two plant endogenous amino acids, aminoadipate and tryptophan, to their respective N-acetylated products in several plant species. We report the crystal structures of BAR, and further delineate structural basis for its substrate selectivity and catalytic mechanism. Through structure-guided protein engineering, we generated several BAR variants that display significantly reduced non-specific activities compared with its wild-type counterpart in vivo. The transgenic expression of enzymes can result in unintended off-target metabolism arising from enzyme promiscuity. Understanding such phenomena at the mechanistic level can facilitate the design of maximally insulated systems featuring heterologously expressed enzymes.

Secular Evolution in Barred Galaxies: Observations

NASA Astrophysics Data System (ADS)

Merrifield, M.

2002-12-01

This paper describes a framework for studying galaxy morphology, particularly bar strength, in a quantitative manner, and presents applications of this approach that reveal observational evidence for secular evolution in bar morphology. The distribution of bar strength in galaxies is quite strongly bimodal, suggesting that barred and unbarred systems are distinct entities, and that any evolution between these two states must occur on a relatively rapid timescale. Bars' strengths appear to be correlated with their pattern speeds, implying that these structures weaken as they start to slow, and disappear entirely before the bars have slowed significantly. There is also tantalizing evidence that bars are rare beyond a redshift of z ~ 0.7, indicating that galaxies have only recently evolved to a point where bars can readily form.

Storage and residence time of suspended sediment in gravel bars of Difficult Run, VA

NASA Astrophysics Data System (ADS)

George, J.; Benthem, A.; Pizzuto, J. E.; Skalak, K.

2016-12-01

Reducing the export of suspended sediment is an important consideration for restoring water quality to the Chesapeake Bay, but sediment budgets for in-channel landforms are poorly constrained. We quantified fine (< 2 mm) sediment storage and residence times for gravel bars at two reaches along Difficult Run, a 5th order tributary to the Potomac River. Eight gravel bars were mapped in a 150m headwater reach at Miller Heights (bankfull width 11m; total bar volume 114 m3) and 6 gravel bars were mapped in a 160m reach downstream near Leesburg Pike (bankfull width 19m; total bar volume 210 m3). Grain size analyses of surface and subsurface samples from 2 bars at each reach indicate an average suspended sediment content of 55%, suggesting a total volume of suspended sediment stored in the mapped bars to be 178 m3, or 283000 kg, comprising 5% of the average annual suspended sediment load of the two study reaches. Estimates of the annual bedload flux at Miller Heights based on stream gaging records and the Wilcock-Crowe bedload transport equation imply that the bars are entirely reworked at least annually. Scour chains installed in 2 bars at each site (a total of 50 chains) recorded scour and fill events during the winter and spring of 2016. These data indicate that 38% of the total volume of the bars is exchanged per year, for a residence time of 2.6 ± 1.2 years, a value we interpret as the residence time of suspended sediment stored in the bars. These results are supported by mapping of topographic changes derived from structure-from-motion analyses of digital aerial imagery. Storage in alluvial bars therefore represents a significant component of the suspended sediment budget of mid-Atlantic streams.

Na2Ti6O13: a potential anode for grid-storage sodium-ion batteries.

PubMed

Rudola, Ashish; Saravanan, Kuppan; Devaraj, Sappani; Gong, Hao; Balaya, Palani

2013-08-28

The ultra-fast (30C or 2 min) rate capability and impressive long cycle life (>5000 cycles) of Na2Ti6O13 are reported. A stable 2.5 V sodium-ion battery full cell is demonstrated. In addition, the sodium storage mechanism and thermal stability of Na2Ti6O13 are discussed.

Investigation of dowel bar placement accuracy with a dowel bar inserter

DOT National Transportation Integrated Search

2003-05-01

Dowel bar inserters (DBI) on concrete paving equipment eliminate the need for manually placing dowel bar baskets. Reduced manual labor eventually pays off the initial investment in a DBI and ultimately results in reduced PCCP costs to the roadway own...

Biphasic voltage-dependent inactivation of human NaV 1.3, 1.6 and 1.7 Na+ channels expressed in rodent insulin-secreting cells.

PubMed

Godazgar, Mahdieh; Zhang, Quan; Chibalina, Margarita V; Rorsman, Patrik

2018-05-01

Na + current inactivation is biphasic in insulin-secreting cells, proceeding with two voltage dependences that are half-maximal at ∼-100 mV and -60 mV. Inactivation of voltage-gated Na + (Na V ) channels occurs at ∼30 mV more negative voltages in insulin-secreting Ins1 and primary β-cells than in HEK, CHO or glucagon-secreting αTC1-6 cells. The difference in inactivation between Ins1 and non-β-cells persists in the inside-out patch configuration, discounting an involvement of a diffusible factor. In Ins1 cells and primary β-cells, but not in HEK cells, inactivation of a single Na V subtype is biphasic and follows two voltage dependences separated by 30-40 mV. We propose that Na V channels adopt different inactivation behaviours depending on the local membrane environment. Pancreatic β-cells are equipped with voltage-gated Na + channels that undergo biphasic voltage-dependent steady-state inactivation. A small Na + current component (10-15%) inactivates over physiological membrane potentials and contributes to action potential firing. However, the major Na + channel component is completely inactivated at -90 to -80 mV and is therefore inactive in the β-cell. It has been proposed that the biphasic inactivation reflects the contribution of different Na V α-subunits. We tested this possibility by expression of TTX-resistant variants of the Na V subunits found in β-cells (Na V 1.3, Na V 1.6 and Na V 1.7) in insulin-secreting Ins1 cells and in non-β-cells (including HEK and CHO cells). We found that all Na V subunits inactivated at 20-30 mV more negative membrane potentials in Ins1 cells than in HEK or CHO cells. The more negative inactivation in Ins1 cells does not involve a diffusible intracellular factor because the difference between Ins1 and CHO persisted after excision of the membrane. Na V 1.7 inactivated at 15--20 mV more negative membrane potentials than Na V 1.3 and Na V 1.6 in Ins1 cells but this small difference is insufficient to solely

Greater gains from smoke-free legislation for non-smoking bar staff in Belfast.

PubMed

Bannon, Finian; Devlin, Anne; McElwee, Gerry; Gavin, Anna

2009-12-01

In April 2007, smoke-free legislation was enacted in workplaces throughout N. Ireland. The effects of this legislation on bar workers' health and their exposure to second-hand smoke at home, work and social environment, and their attitudes to the legislation before and after its implementation remain to be documented. A self-completed questionnaire of bar staff in 35 Belfast bars, before (March 2007, n = 110) and after the legislation (July 2007, n = 110). Smokers (excluding 'social smokers') made up 41.6% of respondents. After the introduction of the smoke-free legislation, the reductions in the proportion of bar workers reporting various respiratory symptoms ranged from 1.3% to 18.6% for smokers and from 21.9% to 33.2% for non-smokers. Likewise, the reductions for various sensory symptoms ranged from 7.3% to 17.7% for smokers and from 29.6% to 46.8% for non-smokers. Reduction in wheeze, cough and throat symptoms after the legislation were much greater for non-smokers than smokers. The proportion of bar staff who reported satisfaction with the legislation remained unchanged across the surveys. Decreases in perceived exposure to second-hand smoke occurred at work, home and in social settings. After the legislation's enactment, a majority of bar workers felt the workplace was healthier (98%). These first findings show reduced reported symptoms among bar workers, both smokers and non-smokers, after the introduction of smoke-free legislation in N. Ireland, though greater among non-smokers. There was also a reported fall in the hours of second-hand smoke exposure in the home for this group of workers which has a high prevalence of smokers.

Mechanisms linking sediment supply and bar morphology: Results from a straight flume with alternate bars

NASA Astrophysics Data System (ADS)

Braudrick, C. A.; Minear, J. T.; Dietrich, W. E.; Dehart, M.; Sklar, L. S.

2008-12-01

One of the largest uncertainties in routing sediment through drainage networks is predicting the degree to which changes in sediment supply are mitigated by changes in sediment storage in bars. We hypothesize that changes in topographic steering link sediment supply and bar morphology. This hypothesis posits that increased sediment supply would enhance topographic steering over the bar, causing the bar to advance laterally into the pool. Contrarily, decreased supply would diminish topographic steering, causing bars to shrink laterally and pools to expand. We examined this hypothesis in a 28-m long, 0.86-m wide flume with a constant discharge of 5.4 l/s and sand with a median grain size of 0.8 mm. The conditions were sufficient to support alternate bars downstream of the upper 8-10 m, and the flume was run for approximately 65 hours at a constant discharge and sediment feed. The equilibrium slope was 0.0033. Once the channel reached equilibrium, the sediment feed was turned off while the discharge was held constant. During the first 25 hours after the feed was stopped, the sediment transport rate at the downstream end of the flume increased from 9.8 to 10.5 kg/hr as sediment was provided by incision at the upstream end of the flume. Because the bed was the only sediment source, sediment supply increased with distance down the flume. Once the feed was shut off, bar response differed between the upstream and downstream portions of the flume. Bars at the downstream end of the flume, where sediment supply increased relative to equilibrium conditions, swelled into the pool. These changes in bar morphology were accompanied by a decrease in surface grain size. Further upstream, where sediment supply was lower, the bars shrunk. These results suggest that there may be a linkage between topographic steering, bar morphology, and sediment supply, but further numerical tests and experimental manipulations are necessary to verify this linkage and to account for the effect of the

The Heat of Formation of Na2SiF6.

ERIC Educational Resources Information Center

DeVore, T. C.; Gallaher, T. N.

1986-01-01

Describes a physical chemistry experiment which uses spectroscopy to measure the heat of formation of Na2SiF6. Discusses the opportunities for students to see the use of a familiar instrument in an unfamiliar application, emphasizing that there are often many ways to attack problems in science. (TW)

Effect of stabilization annealing on SCC susceptibility of β-annealed Ti-6Al-4V alloy in 0.6 M NaCl solution

NASA Astrophysics Data System (ADS)

Jeong, Daeho; Park, Jiho; Ahn, Soojin; Sung, Hyokyung; Kwon, Yongnam; Kim, Sangshik

2018-01-01

The effect of stabilization annealing on the stress corrosion cracking (SCC) susceptibility of β-annealed Ti-6Al-4V (Ti64) alloy was examined in an aqueous 0.6 M NaCl solution under various applied potentials of +0.1, -0.05 and -0.1 V vs Ecorr, respectively, at a strain rate of 10 -6 s -1. The stabilization annealing substantially improved the resistance to SCC of β-annealed Ti64 alloy in 0.6 M NaCl solution under cathodic applied potentials, while the effect was marginal under an anodic applied potential. It was also noted that the areal fraction between ductile and brittle fracture of β-annealed Ti64 specimens, which were slow strain rate tested in 0.6 M NaCl solution, varied with stabilization annealing and applied potentials. The effect of stabilization annealing on the SCC behavior of β-annealed Ti64 alloy in SCC-causing environment was discussed based on the micrographic and fractographic observation.

Numerical simulations of wave propagation in long bars with application to Kolsky bar testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Corona, Edmundo

2014-11-01

Material testing using the Kolsky bar, or split Hopkinson bar, technique has proven instrumental to conduct measurements of material behavior at strain rates in the order of 10 3 s -1. Test design and data reduction, however, remain empirical endeavors based on the experimentalist's experience. Issues such as wave propagation across discontinuities, the effect of the deformation of the bar surfaces in contact with the specimen, the effect of geometric features in tensile specimens (dog-bone shape), wave dispersion in the bars and other particulars are generally treated using simplified models. The work presented here was conducted in Q3 and Q4more » of FY14. The objective was to demonstrate the feasibility of numerical simulations of Kolsky bar tests, which was done successfully.« less

Galaxy Zoo: finding offset discs and bars in SDSS galaxies★

NASA Astrophysics Data System (ADS)

Kruk, Sandor J.; Lintott, Chris J.; Simmons, Brooke D.; Bamford, Steven P.; Cardamone, Carolin N.; Fortson, Lucy; Hart, Ross E.; Häußler, Boris; Masters, Karen L.; Nichol, Robert C.; Schawinski, Kevin; Smethurst, Rebecca J.

2017-08-01

We use multiwavelength Sloan Digital Sky Survey (SDSS) images and Galaxy Zoo morphologies to identify a sample of ˜270 late-type galaxies with an off-centre bar. We measure offsets in the range 0.2-2.5 kpc between the photometric centres of the stellar disc and stellar bar. The measured offsets correlate with global asymmetries of the galaxies, with those with largest offsets showing higher lopsidedness. These findings are in good agreement with predictions from simulations of dwarf-dwarf tidal interactions producing off-centre bars. We find that the majority of galaxies with off-centre bars are of Magellanic type, with a median mass of 109.6 M⊙, and 91 per cent of them having M⋆ < 3 × 1010 M⊙, the characteristic mass at which galaxies start having higher central concentrations attributed to the presence of bulges. We conduct a search for companions to test the hypothesis of tidal interactions, but find that a similar fraction of galaxies with offset bars have companions within 100 kpc as galaxies with centred bars. Although this may be due to the incompleteness of the SDSS spectroscopic survey at the faint end, alternative scenarios that give rise to offset bars such as interactions with dark companions or the effect of lopsided halo potentials should be considered. Future observations are needed to confirm possible low-mass companion candidates and to determine the shape of the dark matter halo, in order to find the explanation for the off-centre bars in these galaxies.

Bar quenching in gas-rich galaxies

NASA Astrophysics Data System (ADS)

Khoperskov, S.; Haywood, M.; Di Matteo, P.; Lehnert, M. D.; Combes, F.

2018-01-01

Galaxy surveys have suggested that rapid and sustained decrease in the star-formation rate (SFR), "quenching", in massive disk galaxies is frequently related to the presence of a bar. Optical and near-IR observations reveal that nearly 60% of disk galaxies in the local universe are barred, thus it is important to understand the relationship between bars and star formation in disk galaxies. Recent observational results imply that the Milky Way quenched about 9-10 Gyr ago, at the transition between the cessation of the growth of the kinematically hot, old, metal-poor thick disk and the kinematically colder, younger, and more metal-rich thin disk. Although perhaps coincidental, the quenching episode could also be related to the formation of the bar. Indeed the transfer of energy from the large-scale shear induced by the bar to increasing turbulent energy could stabilize the gaseous disk against wide-spread star formation and quench the galaxy. To explore the relation between bar formation and star formation in gas rich galaxies quantitatively, we simulated gas-rich disk isolated galaxies. Our simulations include prescriptions for star formation, stellar feedback, and for regulating the multi-phase interstellar medium. We find that the action of stellar bar efficiently quenches star formation, reducing the star-formation rate by a factor of ten in less than 1 Gyr. Analytical and self-consistent galaxy simulations with bars suggest that the action of the stellar bar increases the gas random motions within the co-rotation radius of the bar. Indeed, we detect an increase in the gas velocity dispersion up to 20-35 km s-1 at the end of the bar formation phase. The star-formation efficiency decreases rapidly, and in all of our models, the bar quenches the star formation in the galaxy. The star-formation efficiency is much lower in simulated barred compared to unbarred galaxies and more rapid bar formation implies more rapid quenching.

Star formation suppression and bar ages in nearby barred galaxies

NASA Astrophysics Data System (ADS)

James, P. A.; Percival, S. M.

2018-03-01

We present new spectroscopic data for 21 barred spiral galaxies, which we use to explore the effect of bars on disc star formation, and to place constraints on the characteristic lifetimes of bar episodes. The analysis centres on regions of heavily suppressed star formation activity, which we term `star formation deserts'. Long-slit optical spectroscopy is used to determine H β absorption strengths in these desert regions, and comparisons with theoretical stellar population models are used to determine the time since the last significant star formation activity, and hence the ages of the bars. We find typical ages of ˜1 Gyr, but with a broad range, much larger than would be expected from measurement errors alone, extending from ˜0.25 to >4 Gyr. Low-level residual star formation, or mixing of stars from outside the `desert' regions, could result in a doubling of these age estimates. The relatively young ages of the underlying populations coupled with the strong limits on the current star formation rule out a gradual exponential decline in activity, and hence support our assumption of an abrupt truncation event.

Magnetic Polarizability of Virtual (s\\bar{s}) and (c\\bar{c}) Pairs in the Nucleon

NASA Astrophysics Data System (ADS)

Filip, Peter

2017-12-01

We suggest 3 P 0 quantum state of virtual (s\\bar{s}) pairs in the nucleon can be polarised by the internal fields permeating the volume of the nucleon (proton or neutron). Due to the quadratic Zeeman interaction, 3 P 0 wavefunction of virtual (q\\bar{q}) pairs acquires the admixture of 1 P 10 quantum state in the magnetic field, which generates the antiparallel polarization of s and \\bar{s} quarks (in the nucleon). Considering the internal magnetic fields of neutron and proton (originating from their measured magnetic dipole moments), we suggest the induced s-quark polarization in the neutron to be of the oposite direction compared to the proton case. We mention the influence of the internal chromo-magnetic fields on the quantum state of (q\\bar{q}) pairs in the nucleon and we discuss also the expected behaviour of virtual (c\\bar{c}) pairs.

Implant-retained mandibular bar-supported overlay dentures: a finite element stress analysis of four different bar heights.

PubMed

Rismanchian, Mansoor; Dakhilalian, Mansour; Bajoghli, Farshad; Ghasemi, Ehsan; Sadr-Eshkevari, Pooyan

2012-04-01

Proper stress distribution on dental implants is necessary in bar-retained implant overlay dentures. We aimed to comparatively assess this stress distribution according to different bar heights using finite element models. A three-dimensional (3D) computer model of mandible with 2 implants (ITI, 4.1 mm diameter and 12 mm length) in canine areas and an overlying implant-supported bar-retained overlay denture were simulated with 0-, 1-, 2-, and 3-mm bar heights using ABAQUS software. A vertical force was applied to the left first molar and gradually increased from 0 to 50 N. The resultant stress distribution was evaluated. Bars of 1 and 2 mm in height transferred the least stress to the implants (3.882 and 3.896 MPa, respectively). The 0-mm height of the bar connection transferred the highest stress value (4.277 MPa). The amount of stress transferred by 3-mm heights of the bar connection was greater than that of 1- and 2-mm bar connections and smaller than that of 0-mm bar connection (4.165 kgN). This 3D finite element analysis study suggested that the use of Dolder bar attachment with 1- and 2-mm heights could be associated with appropriate stress distribution for implant-retained overlay dentures.

PLC-dependent intracellular Ca2+ release was associated with C6-ceramide-induced inhibition of Na+ current in rat granule cells.

PubMed

Liu, Zheng; Fei, Xiao-Wei; Fang, Yan-Jia; Shi, Wen-Jie; Zhang, Yu-Qiu; Mei, Yan-Ai

2008-09-01

In this report, the effects of C(6)-ceramide on the voltage-gated inward Na(+) currents (I(Na)), two types of main K(+) current [outward rectifier delayed K(+) current (I(K)) and outward transient K(+) current (I(A))], and cell death in cultured rat cerebellar granule cells were investigated. At concentrations of 0.01-100 microM, ceramide produced a dose-dependent and reversible inhibition of I(Na) without alteration of the steady-state activation and inactivation properties. Treatment with C(2)-ceramide caused a similar inhibitory effect on I(Na). However, dihydro-C(6)-ceramide failed to modulate I(Na). The effect of C(6)-ceramide on I(Na) was abolished by intracellular infusion of the Ca(2+)-chelating agent, 1,2-bis (2-aminophenoxy) ethane-N, N, N9, N9-tetraacetic acid, but was mimicked by application of caffeine. Blocking the release of Ca(2+) from the sarcoplasmic reticulum with ryanodine receptor blocker induced a gradual increase in I(Na) amplitude and eliminated the effect of ceramide on I(Na). In contrast, the blocker of the inositol 1,4,5-trisphosphate-sensitive Ca(2+) receptor did not affect the action of C(6)-ceramide. Intracellular application of GTPgammaS also induced a gradual decrease in I(Na) amplitude, while GDPbetaS eliminated the effect of C(6)-ceramide on I(Na). Furthermore, the C(6)-ceramide effect on I(Na) was abolished after application of the phospholipase C (PLC) blockers and was greatly reduced by the calmodulin inhibitors. Fluorescence staining showed that C(6)-ceramide decreased cell viability and blocking I(Na) by tetrodotoxin did not mimic the effect of C(6)-ceramide, and inhibiting intracellular Ca(2+) release by dantrolene could not decrease the C(6)-ceramide-induced cell death. We therefore suggest that increased PLC-dependent Ca(2+) release through the ryanodine-sensitive Ca(2+) receptor may be responsible for the C(6)-ceramide-induced inhibition of I(Na), which does not seem to be associated with C(6)-ceramide-induced granule

Osmotically-induced tension and the binding of N-BAR protein to lipid vesicles.

PubMed

Hutchison, Jaime B; Karunanayake Mudiyanselage, Aruni P K K; Weis, Robert M; Dinsmore, Anthony D

2016-02-28

The binding affinity of a curvature-sensing protein domain (N-BAR) is measured as a function of applied osmotic stress while the membrane curvature is nearly constant. Varying the osmotic stress allows us to control membrane tension, which provides a probe of the mechanism of binding. We study the N-BAR domain of the Drosophila amphiphysin and monitor its binding on 50 nm-radius vesicles composed of 90 mol% DOPC and 10 mol% PIP. We find that the bound fraction of N-BAR is enhanced by a factor of approximately 6.5 when the tension increases from zero to 2.6 mN m(-1). This tension-induced response can be explained by the hydrophobic insertion mechanism. From the data we extract a hydrophobic domain area that is consistent with known structure. These results indicate that membrane stress and strain could play a major role in the previously reported curvature-affinity of N-BAR.

Changes of Attitudes and Patronage Behaviors in Response to a Smoke-Free Bar Law

PubMed Central

Tang, Hao; Cowling, David W.; Lloyd, Jon C.; Rogers, Todd; Koumjian, Kristi L.; Stevens, Colleen M.; Bal, Dileep G.

2003-01-01

Objectives. We examined patron responses to a California smoke-free bar law. Methods. Three telephone surveys measured attitudes and behavior changes after implementation of the law. Results. Approval of the law rose from 59.8% to 73.2% (odds ratio [OR] = 1.95; 95% confidence interval [CI] = 1.58, 2.40). Self-reported noncompliance decreased from 24.6% to 14.0% (OR = 0.50; 95% CI = 0.30, 0.85). Likelihood of visiting a bar or of not changing bar patronage after the law was implemented increased from 86% to 91% (OR = 1.76; 95% CI = 1.29, 2.40). Conclusions. California bar patrons increasingly support and comply with the smoke-free bar law. PMID:12660206

DD-bar production and their interactions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu Yanrui; Oka, Makoto; Takizawa, Makoto

2011-05-23

We have explored the bound state problem and the scattering problem of the DD-bar pair in a meson exchange model. When considering their production in the e{sup +}e{sup -} process, we included the DD-bar rescattering effect. Although it is difficult to answer whether the S-wave DD-bar bound state exists or not from the binding energies and the phase shifts, one may get an upper limit of the binding energy from the production of the BB-bar, the bottom analog of DD-bar.

Nuss bar migrations: occurrence and classification.

PubMed

Binkovitz, Lauren E; Zendejas, Benjamin; Moir, Christopher R; Binkovitz, Larry A

2016-12-01

Pectus excavatum results from dorsal deviation of the sternum causing narrowing of the anterior-posterior diameter of the chest. It can result in significant cosmetic deformities and cardiopulmonary compromise if severe. The Nuss procedure is a minimally invasive technique that involves placing a thin horizontally oriented metal bar below the dorsal sternal apex for correction of the pectus deformity. To identify the frequency and types of Nuss bar migrations, to present a new categorization of bar migrations, and to present examples of true migrations and pseudomigrations. We retrospectively reviewed the electronic medical records and all pertinent radiologic studies of 311 pediatric patients who underwent a Nuss procedure. We evaluated the frequency and type of bar migrations. Bar migration was demonstrated in 23 of 311 patients (7%) and occurred within a mean period of 26 days after surgery. Bar migrations were subjectively defined as deviation of the bar from the position demonstrated on the immediate postoperative radiographs and categorized as superior, inferior, rotation, lateral or flipped using a new classification system. Sixteen of the 23 migrations required re-operation. Nuss bar migration can be diagnosed with careful evaluation of serial radiographs. Nuss bar migration has a wide variety of appearances and requires exclusion of pseudomigration resulting from changes in patient positioning between radiologic examinations.

Structural studies on a high-pressure polymorph of NaYSi 2O 6

NASA Astrophysics Data System (ADS)

Kahlenberg, Volker; Konzett, Jürgen; Kaindl, Reinhard

2007-06-01

High-pressure synthesis experiments in the system Na 2O-Y 2O 3-SiO 2 revealed the existence of a previously unknown polymorph of NaYSi 2O 6 or Na 3Y 3[Si 3O 9] 2 which was quenched from 3.0 GPa and 1000 °C. Structural investigations on this modification have been performed using single-crystal X-ray diffraction data collected at ambient conditions. Furthermore, unpolarized micro-Raman spectra have been obtained from single-crystal material. The high-P modification of NaYSi 2O 6 crystallizes in the centrosymmetric space group C2/ c with 12 formula units per cell ( a=8.2131(9) Å, b=10.3983(14) Å, c=17.6542(21) Å, β=100.804(9)°, V=1481.0(3) Å 3, R(| F|)=0.033 for 1142 independent observed reflections) and belongs to the group of cyclo-silicates. Basic building units are isolated three-membered [Si 3O 9] rings located in layers parallel to (010). Within a single layer the rings are concentrated in strings parallel to [100]. The sequence of directedness of up ( U) or down ( D) pointing tetrahedra of a single ring is UUU or DDD, respectively. Stacking of the layers parallel to b results in the formation of a three-dimensional structure in which yttrium and sodium cations are incorporated for charge compensation. In more detail, four non-tetrahedral cation positions can be differentiated which are coordinated by 6 and 8 oxygen ligands. Refinements of the site occupancies did not reveal any indication for mixed Na-Y populations on these positions. Finally, several geometrical parameters of rings occurring in cyclo-trisilicate structures have been compiled and are discussed.

Impact of Partial and Comprehensive Smoke-Free Regulations on Indoor Air Quality in Bars

PubMed Central

Kim, Jeonghoon; Ban, Hyunkyung; Hwang, Yunhyung; Ha, Kwonchul; Lee, Kiyoung

2016-01-01

In Korea, smoke-free regulations have been gradually implemented in bars based on venue size. Smoking bans were implemented in 2013 for bars ≥150 m2, in 2014 for bars ≥100 m2, and in 2015 for bars of all sizes. The purpose of this study was to determine indoor fine particle (PM2.5) concentrations in bars before and after implementation of the smoke-free policies based on venue size. Indoor PM2.5 concentrations were measured with real-time aerosol monitors at four time points: (1) pre-regulation (n = 75); (2) after implementing the ban in bars ≥150 m2 (n = 75); (3) after implementing the ban in bars ≥100 m2 (n = 107); and (4) when all bars were smoke-free (n = 79). Our results showed that the geometric mean of the indoor PM2.5 concentrations of all bars decreased from 98.4 μg/m3 pre-regulation to 79.5, 42.9, and 26.6 μg/m3 after the ban on smoking in bars ≥150 m2, ≥100 m2, and all bars, respectively. Indoor PM2.5 concentrations in bars of each size decreased only after the corresponding regulations were implemented. Although smoking was not observed in Seoul bars after smoking was banned in all bars, smoking was observed in 4 of 21 bars in Changwon. Our study concludes that the greatest decrease in PM2.5 concentrations in bars was observed after the regulation covering all bars was implemented. However, despite the comprehensive ban, smoking was observed in bars in Changwon. Strict compliance with the regulations is needed to improve indoor air quality further. PMID:27472349

Impact of Partial and Comprehensive Smoke-Free Regulations on Indoor Air Quality in Bars.

PubMed

Kim, Jeonghoon; Ban, Hyunkyung; Hwang, Yunhyung; Ha, Kwonchul; Lee, Kiyoung

2016-07-26

In Korea, smoke-free regulations have been gradually implemented in bars based on venue size. Smoking bans were implemented in 2013 for bars ≥150 m², in 2014 for bars ≥100 m², and in 2015 for bars of all sizes. The purpose of this study was to determine indoor fine particle (PM2.5) concentrations in bars before and after implementation of the smoke-free policies based on venue size. Indoor PM2.5 concentrations were measured with real-time aerosol monitors at four time points: (1) pre-regulation (n = 75); (2) after implementing the ban in bars ≥150 m² (n = 75); (3) after implementing the ban in bars ≥100 m² (n = 107); and (4) when all bars were smoke-free (n = 79). Our results showed that the geometric mean of the indoor PM2.5 concentrations of all bars decreased from 98.4 μg/m³ pre-regulation to 79.5, 42.9, and 26.6 μg/m³ after the ban on smoking in bars ≥150 m², ≥100 m², and all bars, respectively. Indoor PM2.5 concentrations in bars of each size decreased only after the corresponding regulations were implemented. Although smoking was not observed in Seoul bars after smoking was banned in all bars, smoking was observed in 4 of 21 bars in Changwon. Our study concludes that the greatest decrease in PM2.5 concentrations in bars was observed after the regulation covering all bars was implemented. However, despite the comprehensive ban, smoking was observed in bars in Changwon. Strict compliance with the regulations is needed to improve indoor air quality further.

Interaction between a Mg17Al12 precipitate and { 10\\bar 12} < 10\\bar 12 > twin boundary in magnesium alloys

NASA Astrophysics Data System (ADS)

Li, B.; Mathaudhu, S. N.

Interactions between Mg17Al12 precipitates and { 10\\bar 12} < 10\\bar 1\\bar 1 > twin boundaries (TBs) in magnesium were studied by molecular dynamics simulations. The results obtained agree well with experimental observations in which precipitates can be entirely engulfed by { 10\\bar 12} < 10\\bar 1\\bar 1 > twins without being sheared. Structural analysis of the TBs in the atomic scale shows that the TBs are extremely incoherent during twin growth and highly deviate from the { 10\\bar 12} twinning plane as previously observed in a number of experiments. The simulation studies indicate that { 10\\bar 12} < 10\\bar 1\\bar 1 > twinning was accomplished solely by atomic shuffling that converts the parent lattice to the twin lattice without involving twinning dislocations, resulting in zero shear strain at the TBs.

Predictions for the $$\\bar{B}^{0}\\rightarrow \\bar{K}^{\\ast 0}$$ X(YZ) and $$\\bar{B}^{0}_{s}\\rightarrow\\phi$$ X(YZ) with X(4160), Y(3940), Z(3930)

DOE PAGES

Liang, Wei -Hong; Molina, R.; Xie, Ju -Jun; ...

2015-05-22

We investigate the decay ofmore » $$\\bar B^0 \\to \\bar K^{*0} R$$ and $$\\bar B^0_s \\to \\phi R$$ with $R$ being the $X(4160)$, $Y(3940)$, $Z(3930)$ resonances. Under the assumption that these states are dynamically generated from the vector-vector interaction, as has been concluded from several theoretical studies, we use a reaction mechanism of quark production at the elementary level, followed by hadronization of one final $$q \\bar q$$ pair into two vectors and posterior final state interaction of this pair of vector mesons to produce the resonances. With this procedure we are able to predict five ratios for these decays, which are closely linked to the dynamical nature of these states, and also predict the order of magnitude of the branching ratios which we find of the order of $$10^{-4}$$, well within the present measurable range. In order to further test the dynamical nature of these resonances we study the $$\\bar B^0_s \\to \\phi D^* \\bar D^*$$ and $$\\bar B^0_s \\to \\phi D_s^* \\bar D_s^*$$ decays close to the $$D^* \\bar D^*$$ and $$D_s^* \\bar D_s^*$$ thresholds and make predictions for the ratio of the mass distributions in these decays and the $$\\bar B^0_s \\to \\phi R$$ decay widths. In conclusion, the measurement of these decays rates can help unravel the nature of these resonances.« less

Too Much Bar and Not Enough Mitzvah? A Proposed Research Agenda on Bar/Bat Mitzvah

ERIC Educational Resources Information Center

Schoenfeld, Stuart

2010-01-01

Jewish educators are understandably interested in research on how bar/bat mitzvah affect Jewish education or research on what Jewish schools have done to avoid the distortions of a focus on bar/bat mitzvah. Research might also focus on the somewhat different and more ambitious topic of the role that bar/bat mitzvah play in contemporary Jewish…

Stellar mass distribution of S4G disk galaxies and signatures of bar-induced secular evolution

NASA Astrophysics Data System (ADS)

Díaz-García, S.; Salo, H.; Laurikainen, E.

2016-12-01

Context. Models of galaxy formation in a cosmological framework need to be tested against observational constraints, such as the average stellar density profiles (and their dispersion) as a function of fundamental galaxy properties (e.g. the total stellar mass). Simulation models predict that the torques produced by stellar bars efficiently redistribute the stellar and gaseous material inside the disk, pushing it outwards or inwards depending on whether it is beyond or inside the bar corotation resonance radius. Bars themselves are expected to evolve, getting longer and narrower as they trap particles from the disk and slow down their rotation speed. Aims: We use 3.6 μm photometry from the Spitzer Survey of Stellar Structure in Galaxies (S4G) to trace the stellar distribution in nearby disk galaxies (z ≈ 0) with total stellar masses 108.5 ≲ M∗/M⊙ ≲ 1011 and mid-IR Hubble types - 3 ≤ T ≤ 10. We characterize the stellar density profiles (Σ∗), the stellar contribution to the rotation curves (V3.6 μm), and the m = 2 Fourier amplitudes (A2) as a function of M∗ and T. We also describe the typical shapes and strengths of stellar bars in the S4G sample and link their properties to the total stellar mass and morphology of their host galaxy. Methods: For 1154 S4G galaxies with disk inclinations lower than 65°, we perform a Fourier decomposition and rescale their images to a common frame determined by the size in physical units, by their disk scalelength, and for 748 barred galaxies by both the length and orientation of their bars. We stack the resized density profiles and images to obtain statistically representative average stellar disks and bars in bins of M∗ and T. Based on the radial force profiles of individual galaxies we calculate the mean stellar contribution to the circular velocity. We also calculate average A2 profiles, where the radius is normalized to R25.5. Furthermore, we infer the gravitational potentials from the synthetic bars to

Heterogeneous Reaction of ClONO2(g) + NaCl(s) to Cl2(g) + NaNO3(s)

NASA Technical Reports Server (NTRS)

Timonen, Raimo S.; Chu, Liang T.; Leu, Ming-Taun; Keyser, Leon F.

1994-01-01

The heterogeneous reaction of ClON02 + NaCl yields Cl2 + NaNO3 (eq 1) was investigated over a temperature range 220-300 K in a flow-tube reactor interfaced with a differentially pumped quadrupole mass spectrometer. Partial pressures of ClON02 in the range 10(exp -8) - 10(exp -5) Torr were used. Granule sizes and surface roughness of the NaCl substrates were determined by using a scanning electron microscope, and in separate experiments, surface areas of the substrates were measured by using BET analysis of gas-adsorption isotherms. For dry NaCl substrates, both the decay rates of ClON02 and the growth rates Of C12 were used to obtain reaction probabilities, gamma(sub l) = (4.6 +/- 3.0) x 10(exp -3) at 296 K and (6.7 +/- 3.2) x 10(exp -1) at 225 K, after considering the internal surface area, The error bars represent 1 standard deviation. The Cl2 yield based on the ClONO2 reacted was measured to be 1.0 +/- 0.2. In order to mimic the conditions encountered in the lower stratosphere, the effect of water vapor pressures between 5 x 10(exp -5) and 3 x 10(exp -4) Torr on reaction 1 was also studied. With added H20, reaction probabilities, gamma = (4.1 +/- 2.1) x 10(exp -3) at 296 K and (4.7 +/- 2.9) x 10(exp -3) at 225 K, were obtained. A trace of HOCl, the reaction product from the ClON02 + H20 yield HOCl + HN03 reaction, was observed in addition to the C12 product from reaction 1. The implications of this result for the enhancement of hydrogen chloride in the stratosphere after the El Chichon volcanic eruption and for the marine troposphere are discussed.

Interaction of real and virtual p p bar pairs in J / ψ → p p bar γ (ρ , ω) decays

NASA Astrophysics Data System (ADS)

Milstein, A. I.; Salnikov, S. G.

2017-10-01

The p p bar invariant mass spectra of the processes J / ψ → p p bar ω, J / ψ → p p bar ρ, and J / ψ → p p bar γ close to the p p bar threshold are calculated by means of the N N bar optical potential. The potential model for N N bar interaction in the S10 state is proposed. The parameters of the model are obtained by fitting the cross section of N N bar scattering together with the p p bar invariant mass spectra of the J / ψ decays. Good agreement with the available experimental data is achieved. Using our potential and the Green's function approach we also describe the peak in the η‧π+π- invariant mass spectrum in the decay J / ψ → γη‧π+π- in the energy region near the N N bar threshold.

Glass Fiber Reinforced Polymer Dowel Bar Evaluation

DOT National Transportation Integrated Search

2012-09-01

Glass Fiber Reinforced Polymer (GFRP) dowel bars were installed on one new construction project and two dowel bar : retrofit projects to evaluate the performance of this type of dowel bar in comparison to steel dowel bars installed on the same : cont...

Membrane-Sculpting BAR Domains Generate Stable Lipid Microdomains

PubMed Central

Zhao, Hongxia; Michelot, Alphée; Koskela, Essi V.; Tkach, Vadym; Stamou, Dimitrios; Drubin, David G.; Lappalainen, Pekka

2014-01-01

SUMMARY Bin-Amphiphysin-Rvs (BAR) domain proteins are central regulators of many cellular processes involving membrane dynamics. BAR domains sculpt phosphoinositide-rich membranes to generate membrane protrusions or invaginations. Here, we report that, in addition to regulating membrane geometry, BAR domains can generate extremely stable lipid microdomains by “freezing” phosphoinositide dynamics. This is a general feature of BAR domains, because the yeast endocytic BAR and Fes/CIP4 homology BAR (F-BAR) domains, the inverse BAR domain of Pinkbar, and the eisosomal BAR protein Lsp1 induced phosphoinositide clustering and halted lipid diffusion, despite differences in mechanisms of membrane interactions. Lsp1 displays comparable low diffusion rates in vitro and in vivo, suggesting that BAR domain proteins also generate stable phosphoinositide microdomains in cells. These results uncover a conserved role for BAR superfamily proteins in regulating lipid dynamics within membranes. Stable microdomains induced by BAR domain scaffolds and specific lipids can generate phase boundaries and diffusion barriers, which may have profound impacts on diverse cellular processes. PMID:24055060

Membrane-sculpting BAR domains generate stable lipid microdomains.

PubMed

Zhao, Hongxia; Michelot, Alphée; Koskela, Essi V; Tkach, Vadym; Stamou, Dimitrios; Drubin, David G; Lappalainen, Pekka

2013-09-26

Bin-Amphiphysin-Rvs (BAR) domain proteins are central regulators of many cellular processes involving membrane dynamics. BAR domains sculpt phosphoinositide-rich membranes to generate membrane protrusions or invaginations. Here, we report that, in addition to regulating membrane geometry, BAR domains can generate extremely stable lipid microdomains by "freezing" phosphoinositide dynamics. This is a general feature of BAR domains, because the yeast endocytic BAR and Fes/CIP4 homology BAR (F-BAR) domains, the inverse BAR domain of Pinkbar, and the eisosomal BAR protein Lsp1 induced phosphoinositide clustering and halted lipid diffusion, despite differences in mechanisms of membrane interactions. Lsp1 displays comparable low diffusion rates in vitro and in vivo, suggesting that BAR domain proteins also generate stable phosphoinositide microdomains in cells. These results uncover a conserved role for BAR superfamily proteins in regulating lipid dynamics within membranes. Stable microdomains induced by BAR domain scaffolds and specific lipids can generate phase boundaries and diffusion barriers, which may have profound impacts on diverse cellular processes. Copyright © 2013 The Authors. Published by Elsevier Inc. All rights reserved.

Application of the BAR score as a predictor of short- and long-term survival in liver transplantation patients.

PubMed

de Campos Junior, Ivan Dias; Stucchi, Raquel Silveira Bello; Udo, Elisabete Yoko; Boin, Ilka de Fátima Santana Ferreira

2015-01-01

The balance of risk (BAR) is a prediction system after liver transplantation. To assess the BAR system, a retrospective observational study was performed in 402 patients who had transplant surgery between 1997 and 2012. The BAR score was computed for each patient. Receiver operating characteristic curve analysis with the Hosmer-Lemeshow test was used to calculate sensitivity, specificity, and model calibration. The cutoff value with the best Youden index was selected. Statistical analysis employed the Kaplan-Meier method (log-rank test) for survival, the Mann-Whitney test for group comparison, and multiple logistic regression analysis. 3-month survival was 46% for BAR ≥ 11 and 77% for BAR <11 (p = 0.001); 12-month survival was 44% for BAR ≥ 11 and 69% for BAR <11 (p = 0.001). Factors of survival <3 months were BAR ≥ 11 [odds ratio (OR) 3.08; 95% confidence interval (CI) 1.75-5.42; p = 0.001] and intrasurgical use of packed red blood cells (RBC) above 6 units (OR 4.49; 95% CI 2.73-7.39; p = 0.001). For survival <12 months, factors were BAR ≥ 11 (OR 2.94; 95% CI 1.67-5.16; p = 0.001) and RBC >6 units (OR 2.99; 95% CI 1.92-4.64; p = 0.001). Our study contributes to the incorporation of the BAR system into Brazilian transplantation centers.

Understanding the conductive channel evolution in Na:WO3-x-based planar devices

NASA Astrophysics Data System (ADS)

Shang, Dashan; Li, Peining; Wang, Tao; Carria, Egidio; Sun, Jirong; Shen, Baogen; Taubner, Thomas; Valov, Ilia; Waser, Rainer; Wuttig, Matthias

2015-03-01

An ion migration process in a solid electrolyte is important for ion-based functional devices, such as fuel cells, batteries, electrochromics, gas sensors, and resistive switching systems. In this study, a planar sandwich structure is prepared by depositing tungsten oxide (WO3-x) films on a soda-lime glass substrate, from which Na+ diffuses into the WO3-x films during the deposition. The entire process of Na+ migration driven by an alternating electric field is visualized in the Na-doped WO3-x films in the form of conductive channel by in situ optical imaging combined with infrared spectroscopy and near-field imaging techniques. A reversible change of geometry between a parabolic and a bar channel is observed with the resistance change of the devices. The peculiar channel evolution is interpreted by a thermal-stress-induced mechanical deformation of the films and an asymmetric Na+ mobility between the parabolic and the bar channels. These results exemplify a typical ion migration process driven by an alternating electric field in a solid electrolyte with a low ion mobility and are expected to be beneficial to improve the controllability of the ion migration in ion-based functional devices, such as resistive switching devices.An ion migration process in a solid electrolyte is important for ion-based functional devices, such as fuel cells, batteries, electrochromics, gas sensors, and resistive switching systems. In this study, a planar sandwich structure is prepared by depositing tungsten oxide (WO3-x) films on a soda-lime glass substrate, from which Na+ diffuses into the WO3-x films during the deposition. The entire process of Na+ migration driven by an alternating electric field is visualized in the Na-doped WO3-x films in the form of conductive channel by in situ optical imaging combined with infrared spectroscopy and near-field imaging techniques. A reversible change of geometry between a parabolic and a bar channel is observed with the resistance change of the

Large velocity dispersion of molecular gas in bars of strongly barred galaxies NGC 1300 and NGC 5383

NASA Astrophysics Data System (ADS)

Maeda, Fumiya; Ohta, Kouji; Fujimoto, Yusuke; Habe, Asao; Baba, Junichi

2018-06-01

We carried out ^{12}CO(J = 1-0) observations toward bar and arm regions of the strongly barred galaxies NGC 1300 and NGC 5383 with the Nobeyama 45 m radio telescope (beam size of 1-2 kpc in the galaxies). The aim of the observations is to qualitatively examine a new scenario for the suppression of star formation in bars based on recent high-resolution numerical simulations: higher speed collisions between molecular clouds in the bar region compared with the arm region suppress the massive star formation. CO emissions were detected from all the regions, indicating the presence of molecular gases in the strong bars without associating clear H II regions. In both galaxies, the velocity width of the CO line profile tends to be larger in the bar region than in the arm region, which is qualitatively consistent with the new scenario.

A fast stir bar sorptive extraction method for the analysis of geosmin and 2-methylisoborneol in source and drinking water.

PubMed

Bauld, T; Teasdale, P; Stratton, H; Uwins, H

2007-01-01

The presence of unpleasant taste and odour in drinking water is an ongoing aesthetic concern for water providers worldwide. The need for a sensitive and robust method capable of analysis in both natural and treated waters is essential for early detection of taste and odour events. The purpose of this study was to develop and optimise a fast stir bar sorptive extraction (SBSE) method for the analysis of geosmin and 2-methylisoborneol (MIB) in both natural water and drinking water. Limits of detection with the optimised fast method (45 min extraction time at 60 degrees C using 24 microL stir bars) were 1.1 ng/L for geosmin and 4.2 ng/L for MIB. Relative standard deviations at the detection limits were under 17% for both compounds. Use of multiple stir bars can be used to decrease the detection limits further. The use of 25% NaCl and 5% methanol sample modifiers decreased the experimental recoveries. Likewise, addition of 1 mg/L and 1.5 mg/L NaOCI decreased the recoveries and this effect was not reversed by addition of 10% thiosulphate. The optimised method was used to measure geosmin concentrations in treated and untreated drinking water. MIB concentrations were below the detection limits in these waters.

A Study of Electrochemical Machining of Ti-6Al-4V in NaNO3 solution

NASA Astrophysics Data System (ADS)

Li, Hansong; Gao, Chuanping; Wang, Guoqian; Qu, Ningsong; Zhu, Di

2016-10-01

The titanium alloy Ti-6Al-4V is used in many industries including aviation, automobile manufacturing, and medical equipment, because of its low density, extraordinary corrosion resistance and high specific strength. Electrochemical machining (ECM) is a non-traditional machining method that allows applications to all kinds of metallic materials in regardless of their mechanical properties. It is widely applied to the machining of Ti-6Al-4V components, which usually takes place in a multicomponent electrolyte solution. In this study, a 10% NaNO3 solution was used to make multiple holes in Ti-6Al-4V sheets by through-mask electrochemical machining (TMECM). The polarization curve and current efficiency curve of this alloy were measured to understand the electrical properties of Ti-6Al-4V in a 10% NaNO3 solution. The measurements show that in a 10% NaNO3 solution, when the current density was above 6.56 A·cm-2, the current efficiency exceeded 100%. According to polarization curve and current efficiency curve, an orthogonal TMECM experiment was conducted on Ti-6Al-4V. The experimental results suggest that with appropriate process parameters, high-quality holes can be obtained in a 10% NaNO3 solution. Using the optimized process parameters, an array of micro-holes with an aperture of 2.52 mm to 2.57 mm and maximum roundness of 9 μm were produced using TMECM.

The kinetic enhancement of hydrogen cycling in NaAlH(4) by melt infusion into nanoporous carbon aerogel.

PubMed

Stephens, Robert D; Gross, Adam F; Van Atta, Sky L; Vajo, John J; Pinkerton, Frederick E

2009-05-20

Enhanced kinetic performance and reversibility have been achieved with uncatalyzed NaAlH4 by incorporation into nanoporous carbon aerogel. Aerogel with a pore size distribution peaked at 13 nm and a pore volume of 0.8 cm(3) g(-1) was filled with NaAlH4 to 94% capacity by melt infusion at 189 degrees C under 183 bar H(2) gas overpressure. Dehydrogenation to NaH + Al with reasonable kinetics was accomplished at 150 degrees C, well below the NaAlH4 melting temperature (183 degrees C), compared to hydrogen release above 230 degrees C for bulk uncatalyzed NaAlH4. Uncatalyzed bulk samples did not rehydrogenate under laboratory conditions, whereas NaAlH4 in a carbon aerogel host was readily rehydrogenated at approximately 160 degrees C and 100 bar H(2) to approximately 85% of its initial capacity. Ball-milled NaAlH4 catalyzed with 4 mol% TiCl3 showed somewhat better kinetics compared to the infused aerogel; nevertheless, the large kinetic enhancement obtained by incorporation into carbon aerogel, even in the absence of a catalyst, demonstrates the substantial benefit of confining the NaAlH4 to nanoscale dimensions.

One year of smokefree bars and restaurants in New Zealand: impacts and responses.

PubMed

Thomson, George; Wilson, Nick

2006-03-14

New Zealand introduced a smokefree bars and restaurants policy in December 2004. We reviewed the data available at December 2005 on the main public health, societal and political impacts and responses within New Zealand to the new law. Data were collected from publicly available survey reports, and from government departments and interviews. This included data on smoking in bars, attitudes to smokefree bars, bar patronage, socially cued smoking, and perceived rights to smokefree workplaces. The proportion of surveyed bars with smoking occurring decreased from 95% to 3% during July 2004-April 2005. Between 2004 and 2005, public support for smokefree bars rose from 56% to 69%. In the same period, support for the rights of bar workers to have smokefree workplaces rose from 81% to 91%. During the first ten months of the smokefree bars policy, there were only 196 complaints to officials about smoking in the over 9900 licensed premises. The proportion of smokers who reported that they smoked more than normal at bars, nightclubs, casinos and cafés halved between 2004 and 2005 (from 58% to 29%). Seasonally adjusted sales in bars and clubs changed little (0.6% increase) between the first three quarters of 2004 and of 2005, while café and restaurant sales increased by 9.3% in the same period. Both changes continued existing trends. Compared to the same period in 2004, average employment during the first three quarters of 2005 was up 24% for 'pubs, taverns and bars', up 9% for cafés/restaurants, and down 8% for clubs (though employment in 'pubs, taverns and bars' may have been affected by unusually high patronage around a major sports-series). The proportion of bar managers who approved of smokefree bars increased from 44% to 60% between November 2004 and May 2005. Bar managers also reported increased agreement with the rights of bar workers and patrons to smokefree environments. The main reported concerns of the national and regional Hospitality Associations, in 2005

One year of smokefree bars and restaurants in New Zealand: Impacts and responses

PubMed Central

Thomson, George; Wilson, Nick

2006-01-01

Background New Zealand introduced a smokefree bars and restaurants policy in December 2004. We reviewed the data available at December 2005 on the main public health, societal and political impacts and responses within New Zealand to the new law. Methods Data were collected from publicly available survey reports, and from government departments and interviews. This included data on smoking in bars, attitudes to smokefree bars, bar patronage, socially cued smoking, and perceived rights to smokefree workplaces. Results The proportion of surveyed bars with smoking occurring decreased from 95% to 3% during July 2004 – April 2005. Between 2004 and 2005, public support for smokefree bars rose from 56% to 69%. In the same period, support for the rights of bar workers to have smokefree workplaces rose from 81% to 91%. During the first ten months of the smokefree bars policy, there were only 196 complaints to officials about smoking in the over 9900 licensed premises. The proportion of smokers who reported that they smoked more than normal at bars, nightclubs, casinos and cafés halved between 2004 and 2005 (from 58% to 29%). Seasonally adjusted sales in bars and clubs changed little (0.6% increase) between the first three quarters of 2004 and of 2005, while café and restaurant sales increased by 9.3% in the same period. Both changes continued existing trends. Compared to the same period in 2004, average employment during the first three quarters of 2005 was up 24% for 'pubs, taverns and bars', up 9% for cafés/restaurants, and down 8% for clubs (though employment in 'pubs, taverns and bars' may have been affected by unusually high patronage around a major sports-series). The proportion of bar managers who approved of smokefree bars increased from 44% to 60% between November 2004 and May 2005. Bar managers also reported increased agreement with the rights of bar workers and patrons to smokefree environments. The main reported concerns of the national and regional

Bar Coding and Tracking in Pathology.

PubMed

Hanna, Matthew G; Pantanowitz, Liron

2016-03-01

Bar coding and specimen tracking are intricately linked to pathology workflow and efficiency. In the pathology laboratory, bar coding facilitates many laboratory practices, including specimen tracking, automation, and quality management. Data obtained from bar coding can be used to identify, locate, standardize, and audit specimens to achieve maximal laboratory efficiency and patient safety. Variables that need to be considered when implementing and maintaining a bar coding and tracking system include assets to be labeled, bar code symbologies, hardware, software, workflow, and laboratory and information technology infrastructure as well as interoperability with the laboratory information system. This article addresses these issues, primarily focusing on surgical pathology. Copyright © 2016 Elsevier Inc. All rights reserved.

Bar Coding and Tracking in Pathology.

PubMed

Hanna, Matthew G; Pantanowitz, Liron

2015-06-01

Bar coding and specimen tracking are intricately linked to pathology workflow and efficiency. In the pathology laboratory, bar coding facilitates many laboratory practices, including specimen tracking, automation, and quality management. Data obtained from bar coding can be used to identify, locate, standardize, and audit specimens to achieve maximal laboratory efficiency and patient safety. Variables that need to be considered when implementing and maintaining a bar coding and tracking system include assets to be labeled, bar code symbologies, hardware, software, workflow, and laboratory and information technology infrastructure as well as interoperability with the laboratory information system. This article addresses these issues, primarily focusing on surgical pathology. Copyright © 2015 Elsevier Inc. All rights reserved.

Why Are Some Galaxies Not Barred?

NASA Astrophysics Data System (ADS)

Saha, Kanak; Elmegreen, Bruce

2018-05-01

Although more than two-thirds of star-forming disk galaxies in the local universe are barred, some galaxies remain unbarred, occupying the upper half of the Hubble tuning fork diagram. Numerical simulations almost always produce bars spontaneously, so it remains a challenge to understand how galaxies sometimes prevent bars from forming. Using a set of collisionless simulations, we first reproduce the common result that cold stellar disks surrounding a classical bulge become strongly unstable to non-axisymmetric perturbations, leading to the rapid formation of spiral structure and bars. However, our analyses show that galaxy models with compact classical bulges (whose average density is greater than or comparable to the disk density calculated within bulge half-mass radii) are able to prevent bar formation for at least 4 Gyr even when the stellar disk is maximal and having low Toomre Q. Such bar prevention is the result of several factors such as (a) a small inner Lindblad resonance with a high angular rate, which contaminates an incipient bar with x 2 orbits, and (b) rapid loss of angular momentum accompanied by a rapid heating in the center from initially strong bar and spiral instabilities in a low-Q disk; in other words, a rapid initial rise to a value larger than ∼5 of the ratio of the random energy to the rotational energy in the central region of the galaxy.

Comparative investigation of the solution species [U(CO3)5]6- and the crystal structure of Na6[U(CO3)5].12H2O.

PubMed

Hennig, Christoph; Ikeda-Ohno, Atsushi; Emmerling, Fanziska; Kraus, Werner; Bernhard, Gert

2010-04-21

The limiting U(IV) carbonate species in aqueous solution was investigated by comparing its structure parameters with those of the complex preserved in a crystal structure. The solution species prevails in aqueous solution of 0.05 M U(IV) and 1 M NaHCO(3) at pH 8.3. Single crystals of Na(6)[U(CO(3))(5)].12H(2)O were obtained directly from this mother solution. The U(IV) carbonate complex in the crystal structure was identified as a monomeric [U(CO(3))(5)](6-) anionic complex. The interatomic distances around the U(IV) coordination polyhedron show average distances of U-O = 2.461(8) A, U-C = 2.912(4) A and U-O(dist) = 4.164(6) A. U L(3)-edge EXAFS spectra were collected from the solid Na(6)[U(CO(3))(5)].12H(2)O and the corresponding solution. The first shell of the Fourier transforms (FTs) revealed, in both samples, a coordination of ten oxygen atoms at an average U-O distance of 2.45 +/- 0.02 A, the second shell originates from five carbon atoms with a U-C distance of 2.91 +/- 0.02 A, and the third shell was fit with single and multiple scattering paths of the distal oxygen at 4.17 +/- 0.02 A. These data indicate the identity of the [U(CO(3))(5)](6-) complex in solid and solution state. The high negative charge of the [U(CO(3))(5)](6-) anion is compensated by Na(+) cations. In solid state the Na(+) cations form a bridging network between the [U(CO(3))(5)](6-) units, while in liquid state the Na(+) cations seem to be located close to the anionic complex. The average metal-oxygen distances of the coordination polyhedron show a linear correlation to the radius contraction of the neighbouring actinide(IV) ions and indicate the equivalence of the [An(CO(3))(5)](6-) coordination within the series of thorium, uranium, neptunium and plutonium.

Analytical potential-density pairs for bars

NASA Astrophysics Data System (ADS)

Vogt, D.; Letelier, P. S.

2010-11-01

An identity that relates multipolar solutions of the Einstein equations to Newtonian potentials of bars with linear densities proportional to Legendre polynomials is used to construct analytical potential-density pairs of infinitesimally thin bars with a given linear density profile. By means of a suitable transformation, softened bars that are free of singularities are also obtained. As an application we study the equilibrium points and stability for the motion of test particles in the gravitational field for three models of rotating bars.

Preparation of a Breadfruit Flour Bar.

PubMed

Nochera, Carmen L; Ragone, Diane

2016-05-20

Breadfruit is a nutritious, high energy food with a low quantity of protein but excellent protein quality. It has the potential to be developed into desired products which will help increase its utilization and add value to the crop. The overall purposes of this investigation were to develop a portable, nutritious, ready-to-eat breadfruit product (bar), test the sensory qualities of the product, and evaluate the nutritional properties of the product. Flour made from the Micronesian variety, Meinpadahk ( Artocarpus altilis × Artocarpus mariannensis ), was utilized for the development of the breadfruit bar. Breadfruit is a rich source of fiber, vitamins such as vitamin C, minerals such as potassium, and phytochemicals such as flavonoids. Nutritional labeling indicates that the breadfruit bar is high in carbohydrates and low in fat, and sensory evaluation indicates that 81% of the panelists found the bar acceptable while 19% disliked the bar. The breadfruit bar can provide an appealing and inexpensive gluten-free food source based on locally available breadfruit.

Moisture sorption curves of fruit and nut cereal bar prepared with sugar and sugar substitutes.

PubMed

Pallavi, Byrappa Vasu; Chetana, Ramakrishna; Ravi, Ramaswamy; Reddy, Sunkireddy Yella

2015-03-01

Low sugar, low fat, dry fruit and nut cereal bars without sugar were prepared using cereals, nuts, and sugar substitutes. The sorption characteristics of the bars prepared with sugar substitutes in comparison with that of sugar were studied by keeping the bars at water activity (aw) from 0.1 to 0.9. The sorption isotherms of low sugar bars were practically identical below aw of 0.5 but above aw of 0.5, a clear differentiation in the isotherms could be observed compared to that of sugar counterpart. A sharp increase in moisture content was observed in the bars prepared with alternative sweeteners, above aw 0.6, whereas a gradual increase in aw was observed in the case of bar prepared with sugar. The ERH (Equilibrium relative humidity) value for bar with sugar was 50 %, and for bars prepared with alternative sweeteners, it was about 60 %. Low sugar cereal bar prepared with sorbitol + maltitol (SM) syrup scored higher sensory quality compared to other product prepared with sorbitol + nutriose (SN) as the former retained softness and chewiness on storage. Thus, it was observed that bars with alternative sweeteners will be more stable as their ERH is closer to normal ambient conditions compared to that prepared with sugar.

Trend of change in retentive force for bar attachments with different materials.

PubMed

Saito, Marie; Kanazawa, Manabu; Takahashi, Hidekazu; Uo, Motohiro; Minakuchi, Shunsuke

2014-12-01

Attachment wear can decrease the retentive force of 2-implant overdentures (2-IODs). The purpose of this in vitro study was to investigate the trend of change in retentive force for 6 different bar attachments during dislodgement. Round and Dolder bars were made of platinum-added gold alloy (PGA), cobalt chromium alloy (Co-Cr), and commercially pure titanium grade IV (Ti). Clips were made of PGA. Retentive force was measured during 7200 dislodging cycles. Simple linear regression analysis was performed in order to investigate the relationship between number of cycles and retentive force (P<.05). Subsequently, wear debris was analyzed, and the surface of the attachments was observed. The retentive force of the Co-Cr round bar attachment (CoCr-R) increased from 57.5 N to 68.3 N and the Ti round bar attachment (Ti-R) from 54.8 N to 59.7 N. However, the retentive force of the PGA round bar attachment (PGA-R) decreased from 69.3 N to 64.0 N. A positive relationship was found between the number of cycles and the retentive force of both CoCr-R and Ti-R. The composition of the wear debris was almost the same as for PGA. For the Dolder bar attachment, no changes were seen in retentive force (between 7.0 N to 12.0 N). For the round bar attachment, the PGA clip and PGA bar showed wear. The retentive force of PGA-R slightly decreased. The retentive force of CoCr-R and Ti-R tended to increase. For the Dolder bar attachment, all 3 types of bar attachment showed no wear. Copyright © 2014 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

49 CFR 236.705 - Bar, locking.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Bar, locking. 236.705 Section 236.705..., MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Definitions § 236.705 Bar, locking. A bar in an interlocking machine to which the locking dogs are attached. ...

Syntheses and structural characterization of non-centrosymmetric Na{sub 2}M{sub 2}M'S{sub 6} (M, M′=Ga, In, Si, Ge, Sn, Zn, Cd) sulfides

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yohannan, Jinu P.; Vidyasagar, Kanamaluru, E-mail: kvsagar@iitm.ac.in

Seven new non-centrosymmetric Na{sub 2}M{sub 2}M’S{sub 6} sulfides, namely, Na{sub 2}Sn{sub 2}ZnS{sub 6}(1){sub ,} Na{sub 2}Ga{sub 2}GeS{sub 6}(2), Na{sub 2}Ga{sub 2}SnS{sub 6}(3-α), Na{sub 2}Ga{sub 2}SnS{sub 6}(3-β){sub ,} Na{sub 2}Ge{sub 2}ZnS{sub 6}(4){sub ,} Na{sub 2}Ge{sub 2}CdS{sub 6}(5){sub ,} Na{sub 2}In{sub 2}SiS{sub 6}(6) and Na{sub 2}In{sub 2}GeS{sub 6}(7), were synthesized by high temperature solid state reactions and structurally characterized by single crystal X-ray diffraction. They crystallize in non-centrosymmetric Fdd2 and Cc space groups and their three-dimensional [M{sub 2}M′S{sub 6}]{sup 2-}framework structures consist of MS{sub 4} and M′S{sub 4} tetrahedra corner-connected to one another in either orderly or disordered fashion. Sodium ions residemore » in the tunnels of the anionic framework. Compounds 1, 2 and 3-α have the structure of known Li{sub 2}Ga{sub 2}GeS{sub 6}, whereas compounds 6 and 7 are isostructural with known Li{sub 2}In{sub 2}GeS{sub 6} compound. Isostructural compounds 4 and 5 represent a new structural variant. Compounds 3-α and its new monoclinic structural variant 3-β have disordered structural framework. All of them are wide band gap semiconductors. Na{sub 2}Ga{sub 2}GeS{sub 6}(2), Na{sub 2}Ga{sub 2}SnS{sub 6}(3), Na{sub 2}Ge{sub 2}ZnS{sub 6}(4) and Na{sub 2}In{sub 2}GeS{sub 6}(7) compounds are found to be second-harmonic generation (SHG) active. Compounds 1, 2 and 3-α melt congruently. - Graphical abstract: Na{sub 2}Ga{sub 2}GeS{sub 6}, Na{sub 2}Ga{sub 2}SnS{sub 6}, Na{sub 2}Ge{sub 2}ZnS{sub 6}, Na{sub 2}In{sub 2}GeS{sub 6}, Na{sub 2}Sn{sub 2}ZnS{sub 6}, Na{sub 2}Ge{sub 2}CdS{sub 6} and Na{sub 2}In{sub 2}SiS{sub 6} have non-centrosymmetric structures and the first four compounds are SHG active. Display Omitted - Highlights: • Seven new Na{sub 2}M{sub 2}M′S{sub 6} compounds with non-centrosymmetric structures were synthesized. • They are wide band gap semiconductors. • Na{sub 2}Ga{sub 2}GeS{sub 6

The solubility of quartz in aqueous sodium chloride solution at 350°C and 180 to 500 bars

USGS Publications Warehouse

Fournier, Robert O.; Rosenbauer, Robert J.; Bischoff, James L.

1982-01-01

The solubility of quartz in 2, 3, and 4 molal NaCl was measured at 350°C and pressures ranging from 180 to 500 bars. The molal solubility in each of the salt solutions is greater than that in pure water throughout the measured pressure range, with the ratio of solubility in NaCl solution to solubility in pure water decreasing as pressure is increased. The measured solubilities are significantly higher than solubilities calculated using a simple model in which the water activity in NaCl solutions decreases either in proportion to decreasing vapor pressure of the solution as salinity is increased or in proportion to decreasing mole fraction of water in the solvent.

The intrinsic three-dimensional shape of galactic bars

NASA Astrophysics Data System (ADS)

Méndez-Abreu, J.; Costantin, L.; Aguerri, J. A. L.; de Lorenzo-Cáceres, A.; Corsini, E. M.

2018-06-01

We present the first statistical study on the intrinsic three-dimensional (3D) shape of a sample of 83 galactic bars extracted from the CALIFA survey. We use the galaXYZ code to derive the bar intrinsic shape with a statistical approach. The method uses only the geometric information (ellipticities and position angles) of bars and discs obtained from a multi-component photometric decomposition of the galaxy surface-brightness distributions. We find that bars are predominantly prolate-triaxial ellipsoids (68%), with a small fraction of oblate-triaxial ellipsoids (32%). The typical flattening (intrinsic C/A semiaxis ratio) of the bars in our sample is 0.34, which matches well the typical intrinsic flattening of stellar discs at these galaxy masses. We demonstrate that, for prolate-triaxial bars, the intrinsic shape of bars depends on the galaxy Hubble type and stellar mass (bars in massive S0 galaxies are thicker and more circular than those in less massive spirals). The bar intrinsic shape correlates with bulge, disc, and bar parameters. In particular with the bulge-to-total (B/T) luminosity ratio, disc g - r color, and central surface brightness of the bar, confirming the tight link between bars and their host galaxies. Combining the probability distributions of the intrinsic shape of bulges and bars in our sample we show that 52% (16%) of bulges are thicker (flatter) than the surrounding bar at 1σ level. We suggest that these percentages might be representative of the fraction of classical and disc-like bulges in our sample, respectively.

Search for the Standard Model Higgs Boson in ZH → v$$\\bar{v}$$b$$\\bar{b}$$ channel in p$$\\bar{p}$$ collisions at √s= 1.96 TeV

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dubey, Abhinav

2011-01-01

A search for the standard model Higgs boson is performed in 5.2 fb -1 of pmore » $$\\bar{p}$$ collisions at p √s = 1.96 TeV, collected with the DØ detector at the Fermilab Tevatron. The final state considered is a pair of b jets with large missing transverse energy, as expected from p$$\\bar{p}$$→ ZH → v$$\\bar{v}$$b$$\\bar{b}$$ production. The search is also sensitive to the WH → ℓvb$$\\bar{b}$$ channel, where the charged lepton is not identified. Boosted decision trees are used to discriminate signal from background. Good agreement is observed between data and expected backgrounds, and, for a Higgs-boson mass of 115 GeV, a limit is set at 95% C.L. on the cross section multiplied by branching fraction of (p$$\\bar{p}$$ → (Z/W)H) × (H → b$$\\bar{b}$$) that is a factor 4.57 expected and 3.73 observed larger than the value expected from the standard model.« less

Development of ceramic-coated weld backing bars

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eggleston, B.R.

1994-10-20

In shipbuilding and many other industries, copper weld backing bars are used to draw the heat out of the weld. The problem that some users of these bars encounter is that these bars, on occasion, actually melt in spots and become welded to the weld plates. After this happens a number of times, the backing bar becomes so degraded that it must be either discarded or machined, both of which are very costly and time-consuming actions. To avoid this fusion between the backing bar and the weld plate, the weld processes that are used cannot be ones of high beatmore » input. This requirement is very limiting when thick plates are being welded. The plates must be beveled, and more weld passes must be run. These problems are also costly and time consuming. The aim of this project is to find a way to produce backing bars with nearly the same `chilling` effect but with both a greater resistance to molten metal and resistance to arcing to the backing bar itself. A possible solution currently being tested is to coat the copper bars with a thin layer of a ceramic coating. The procedure used was to coat the copper bars with either alumina or spinel by a plasma spraying method.« less

Unit-bar migration and bar-trough deposition: impacts on hydraulic conductivity and grain size heterogeneity in a sandy streambed

NASA Astrophysics Data System (ADS)

Korus, Jesse T.; Gilmore, Troy E.; Waszgis, Michele M.; Mittelstet, Aaron R.

2018-03-01

The hydrologic function of riverbeds is greatly dependent upon the spatiotemporal distribution of hydraulic conductivity and grain size. Vertical hydraulic conductivity ( K v) is highly variable in space and time, and controls the rate of stream-aquifer interaction. Links between sedimentary processes, deposits, and K v heterogeneity have not been well established from field studies. Unit bars are building blocks of fluvial deposits and are key to understanding controls on heterogeneity. This study links unit bar migration to K v and grain size variability in a sand-dominated, low-sinuosity stream in Nebraska (USA) during a single 10-day hydrologic event. An incipient bar formed parallel to the thalweg and was highly permeable and homogenous. During high flow, this bar was submerged under 10-20 cm of water and migrated 100 m downstream and toward the channel margin, where it became markedly heterogeneous. Low- K v zones formed in the subsequent heterogeneous bar downstream of the original 15-40-cm-thick bar front and past abandoned bridge pilings. These low- K v zones correspond to a discontinuous 1-cm layer of fine sand and silt deposited in the bar trough. Findings show that K v heterogeneity relates chiefly to the deposition of suspended materials in low-velocity zones downstream of the bar and obstructions, and to their subsequent burial by migration of the bar during high flow. Deposition of the unit bar itself, although it emplaced the vast majority of the sediment volume, was secondary to bar-trough deposition as a control on the overall pattern of heterogeneity.

Location of School Lunch Salad Bars and Fruit and Vegetable Consumption in Middle Schools: A Cross-Sectional Plate Waste Study.

PubMed

Adams, Marc A; Bruening, Meg; Ohri-Vachaspati, Punam; Hurley, Jane C

2016-03-01

The school lunch environment is a prime target for increasing a child's consumption of fresh fruits and vegetables (F/V). Salad bars are heavily encouraged in schools; however, more research is needed to examine the contexts in which salad bars promote consumption of F/V among students. To compare the amount of fresh F/V self-served, consumed, and wasted by students during lunch at schools with differing salad bar placement: inside or outside of the serving line. Cross-sectional plate waste study in which salad bar placement differed between schools. A random sample of middle school students (N=533) from six schools (three schools per district). Amount of fresh F/V taken, consumed, and wasted. Negative binomial multivariable regression examined placement of salad bars, adjusting for sex, grade, race/ethnicity, free/reduced status, day of the week, and nesting of students within schools. Almost all students (98.6%) in the schools with salad bars inside serving lines self-served F/V compared with only 22.6% of students in the schools with salad bars outside lines (adjusted prevalence ratio=5.38; 95% CI 4.04 to 7.17). Similarly, students at schools with salad bars inside the line had greater prevalence of consuming any F/V compared with students in schools with salad bars outside the line (adjusted prevalence ratio=4.83; 95% CI 3.40 to 6.81). On average, students with the salad bar outside the line wasted less F/V compared with those with salad bars inside the line (30% vs 48%, respectively). Few students visited salad bars located outside the lunch line. Salad bars inside the lunch line resulted in significantly greater fresh F/V taken, consumed, and wasted. When possible, schools should try to include salad bars inside the line to increase students' exposure to F/V. Copyright © 2016 Academy of Nutrition and Dietetics. Published by Elsevier Inc. All rights reserved.

Feasibility and acceptability of a bar-based sexual risk reduction intervention for bar patrons in Tshwane, South Africa.

PubMed

Morojele, Neo K; Kitleli, Naledi; Ngako, Kgalabi; Kekwaletswe, Connie T; Nkosi, Sebenzile; Fritz, Katherine; Parry, Charles D H

2014-01-01

Alcohol consumption is a recognised risk factor for HIV infection. Alcohol serving establishments have been identified as appropriate venues in which to deliver HIV prevention interventions. This paper describes experiences and lessons learnt from implementing a combined HIV prevention intervention in bar settings in one city- and one township-based bar in Tshwane, South Africa. The intervention consisted of peer-led and brief intervention counselling sub-components. Thirty-nine bar patrons were recruited and trained, and delivered HIV and alcohol risk reduction activities to their peers as peer interventionists. At the same time, nine counsellors received training and visited the bars weekly to provide brief motivational interviewing counselling, advice, and referrals to the patrons of the bars. A responsible server sub-component that had also been planned was not delivered as it was not feasible to train the staff in the two participating bars. Over the eight-month period the counsellors were approached by and provided advice and counselling for alcohol and sexual risk-related problems to 111 bar patrons. The peer interventionists reported 1323 risk reduction interactions with their fellow bar patrons during the same period. The intervention was overall well received and suggests that bar patrons and servers can accept a myriad of intervention activities to reduce sexual risk behaviour within their drinking settings. However, HIV- and AIDS-related stigma hindered participation in certain intervention activities in some instances. The buy-in that we received from the relevant stakeholders (i.e. bar owners/managers and patrons, and the community at large) was an important contributor to the feasibility and acceptability of the intervention.

Feasibility and acceptability of a bar-based sexual risk reduction intervention for bar patrons in Tshwane, South Africa

PubMed Central

Morojele, Neo K.; Kitleli, Naledi; Ngako, Kgalabi; Kekwaletswe, Connie T.; Nkosi, Sebenzile; Fritz, Katherine; Parry, Charles D.H.

2014-01-01

Abstract Alcohol consumption is a recognised risk factor for HIV infection. Alcohol serving establishments have been identified as appropriate venues in which to deliver HIV prevention interventions. This paper describes experiences and lessons learnt from implementing a combined HIV prevention intervention in bar settings in one city- and one township-based bar in Tshwane, South Africa. The intervention consisted of peer-led and brief intervention counselling sub-components. Thirty-nine bar patrons were recruited and trained, and delivered HIV and alcohol risk reduction activities to their peers as peer interventionists. At the same time, nine counsellors received training and visited the bars weekly to provide brief motivational interviewing counselling, advice, and referrals to the patrons of the bars. A responsible server sub-component that had also been planned was not delivered as it was not feasible to train the staff in the two participating bars. Over the eight-month period the counsellors were approached by and provided advice and counselling for alcohol and sexual risk-related problems to 111 bar patrons. The peer interventionists reported 1323 risk reduction interactions with their fellow bar patrons during the same period. The intervention was overall well received and suggests that bar patrons and servers can accept a myriad of intervention activities to reduce sexual risk behaviour within their drinking settings. However, HIV- and AIDS-related stigma hindered participation in certain intervention activities in some instances. The buy-in that we received from the relevant stakeholders (i.e. bar owners/managers and patrons, and the community at large) was an important contributor to the feasibility and acceptability of the intervention. PMID:24750106

Detection of Bar Transgenic Sugarcane with a Rapid and Visual Loop-Mediated Isothermal Amplification Assay.

PubMed

Zhou, Dinggang; Wang, Chunfeng; Li, Zhu; Chen, Yun; Gao, Shiwu; Guo, Jinlong; Lu, Wenying; Su, Yachun; Xu, Liping; Que, Youxiong

2016-01-01

Genetic engineering offers an attractive alternative in sugarcane breeding for increasing cane and sugar yields as well as disease and insect resistance. Bar transgenic sugarcane employing the herbicide tolerance is a useful agronomical trait in weed control. In this study, a loop-mediated isothermal amplification (LAMP) assay for rapid detection of the bar gene in transgenic sugarcane has been developed and evaluated. A set of six primers was designed for LAMP-based amplification of the bar gene. The LAMP reaction conditions were optimized as follows: 5.25 mM of Mg(2+), 6:1 ratio of inner vs. outer primer, and 6.0 U of Bst DNA polymerase in a reaction volume of 25.0 μL. The detection limit of the recombinant plasmid 1Ac0229 was as low as 10 copies in the developed LAMP, which was 10-fold higher sensitive than that of conventional PCR. In 100 putative transgenic lines, the bar gene was detected in 100/100 cases (100%) by LAMP and 97/100 cases (97%) by conventional PCR, respectively. In conclusion, the developed LAMP assay is visual, rapid, sensitive, reliable, and cost-effective for detection of the bar specific transgenic sugarcane.

Detection of Bar Transgenic Sugarcane with a Rapid and Visual Loop-Mediated Isothermal Amplification Assay

PubMed Central

Zhou, Dinggang; Wang, Chunfeng; Li, Zhu; Chen, Yun; Gao, Shiwu; Guo, Jinlong; Lu, Wenying; Su, Yachun; Xu, Liping; Que, Youxiong

2016-01-01

Genetic engineering offers an attractive alternative in sugarcane breeding for increasing cane and sugar yields as well as disease and insect resistance. Bar transgenic sugarcane employing the herbicide tolerance is a useful agronomical trait in weed control. In this study, a loop-mediated isothermal amplification (LAMP) assay for rapid detection of the bar gene in transgenic sugarcane has been developed and evaluated. A set of six primers was designed for LAMP-based amplification of the bar gene. The LAMP reaction conditions were optimized as follows: 5.25 mM of Mg2+, 6:1 ratio of inner vs. outer primer, and 6.0 U of Bst DNA polymerase in a reaction volume of 25.0 μL. The detection limit of the recombinant plasmid 1Ac0229 was as low as 10 copies in the developed LAMP, which was 10-fold higher sensitive than that of conventional PCR. In 100 putative transgenic lines, the bar gene was detected in 100/100 cases (100%) by LAMP and 97/100 cases (97%) by conventional PCR, respectively. In conclusion, the developed LAMP assay is visual, rapid, sensitive, reliable, and cost-effective for detection of the bar specific transgenic sugarcane. PMID:27014303

Na{sub 6}B{sub 13}O{sub 22.5}, a new noncentrosymmetric sodium borate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Penin, N.; Touboul, M.; Nowogrocki, G.

2005-03-15

Na{sub 6}B{sub 13}O{sub 22.5} (B/Na=2.17) single crystals were obtained by heating, melting and appropriately cooling borax, Na{sub 2}[B{sub 4}O{sub 5}(OH){sub 4}].8H{sub 2}O. Its formula has been determined by the resolution of the structure from single-crystal X-ray diffraction data. The compound crystallizes in the noncentrosymmetric orthorhombic Iba2 space group, with the following unit cell parameters: a=33.359(11)A, b=9.554(3)A, c=10.644(4)A; V=3392.4(19)A{sup 3}; Z=8. The crystal structure was solved from 3226 reflections until R{sub 1}=0.0385. It exhibits a three-dimensional framework built up from BO{sub 3} triangles ({delta}) and BO{sub 4} tetrahedra (T). Two kinds of borate groups can be considered forming two different doublemore » B{sub 3}O{sub 3} rings: two B{sub 4}O{sub 9} (linkage by two boron atoms) and one B{sub 5}O{sub 11} (linkage by one boron atom); the shorthand notation of the new fundamental building block (FBB) existing in this compound is: 13: {infinity}{sup 3} [(5: 3{delta}+2T)+2(4: 2{delta}+2T)]. The discovery of this new borate questions the real number of Na{sub 2}B{sub 4}O{sub 7} varieties. The existence of Na{sub 6}B{sub 13}O{sub 22.5} (B/Na=2.17) and of another recently discovered borate, Na{sub 3}B{sub 7}O{sub 12} (B/Na=2.33; FBB 7: {infinity}{sup 3} [(3: 2{delta}+T)+(3: {delta}+2T)+(1: {delta})], with a composition close to the long-known borate {alpha}-Na{sub 2}B{sub 4}O{sub 7} (B/Na=2; FBB 8: {infinity}{sup 3} [(5: 3{delta}+2T)+(3: 2{delta}+T)], may explain the very complex equilibria reported in the Na{sub 2}O-B{sub 2}O{sub 3} phase diagram, especially in this range of composition.« less

BAR domain proteins regulate Rho GTPase signaling.

PubMed

Aspenström, Pontus

2014-01-01

BAR proteins comprise a heterogeneous group of multi-domain proteins with diverse biological functions. The common denominator is the Bin-Amphiphysin-Rvs (BAR) domain that not only confers targeting to lipid bilayers, but also provides scaffolding to mold lipid membranes into concave or convex surfaces. This function of BAR proteins is an important determinant in the dynamic reconstruction of membrane vesicles, as well as of the plasma membrane. Several BAR proteins function as linkers between cytoskeletal regulation and membrane dynamics. These links are provided by direct interactions between BAR proteins and actin-nucleation-promoting factors of the Wiskott-Aldrich syndrome protein family and the Diaphanous-related formins. The Rho GTPases are key factors for orchestration of this intricate interplay. This review describes how BAR proteins regulate the activity of Rho GTPases, as well as how Rho GTPases regulate the function of BAR proteins. This mutual collaboration is a central factor in the regulation of vital cellular processes, such as cell migration, cytokinesis, intracellular transport, endocytosis, and exocytosis.

Measurement of the t $$\\bar{t}$$ Cross-Section Using the Dimuon Channel in p$$\\bar{p}$$ Collisions at √s = 1.96-TeV

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCroskey, Robert Crampton

2004-01-01

The author has measured the tmore » $$\\bar{t}$$ production cross section at √s = 1.96 TeV using data collected by the D0 experiment at Fermilab. The integrated luminosity of the data set is 140 pb -1 and a total of four candidate events are seen, with an expected background of 2.61 events. The measured cross section of σ t$$\\bar{t}$$ = 11.1$$+22.1\\atop{-9.3}$$(stat.)$$+4.3\\atop{-4.5}$$(sys.) pb is in agreement with a NNLO calculation of 6.77 pb.« less

Why Buckling Stellar Bars Weaken in Disk Galaxies

NASA Astrophysics Data System (ADS)

Martinez-Valpuesta, Inma; Shlosman, Isaac

2004-09-01

Young stellar bars in disk galaxies experience a vertical buckling instability that terminates their growth and thickens them, resulting in a characteristic peanut/boxy shape when viewed edge-on. Using N-body simulations of galactic disks embedded in live halos, we have analyzed the bar structure throughout this instability and found that the outer (approximately) third of the bar dissolves completely while the inner part (within the vertical inner Lindblad resonance) becomes less oval. The bar acquires the frequently observed peanut/boxy-shaped isophotes. We also find that the bar buckling is responsible for a mass injection above the plane, which is subsequently trapped by specific three-dimensional families of periodic orbits of particular shapes explaining the observed isophotes, in line with previous work. Using a three-dimensional orbit analysis and surfaces of sections, we infer that the outer part of the bar is dissolved by a rapidly widening stochastic region around its corotation radius-a process related to the bar growth. This leads to a dramatic decrease in the bar size, decrease in the overall bar strength, and a mild increase in its pattern speed but is not expected to lead to a complete bar dissolution. The buckling instability appears primarily responsible for shortening the secular diffusion timescale to a dynamical one when building the boxy isophotes. The sufficiently long timescale of the described evolution, ~1 Gyr, can affect the observed bar fraction in the local universe and at higher redshifts, both through reduced bar strength and the absence of dust offset lanes in the bar.

Effect of Cooling Rate on SCC Susceptibility of β-Processed Ti-6Al-4V Alloy in 0.6M NaCl Solution

NASA Astrophysics Data System (ADS)

Ahn, Soojin; Park, Jiho; Jeong, Daeho; Sung, Hyokyung; Kwon, Yongnam; Kim, Sangshik

2018-03-01

The effects of cooling rate on the stress corrosion cracking (SCC) susceptibility of β-processed Ti-6Al-4V (Ti64) alloy, including BA/S specimen with furnace cooling and BQ/S specimen with water quenching, were investigated in 0.6M NaCl solution under various applied potentials using a slow strain rate test technique. It was found that the SCC susceptibility of β-processed Ti64 alloy in aqueous NaCl solution decreased with fast cooling rate, which was particularly substantial under an anodic applied potential. The micrographic and fractographic analyses suggested that the enhancement with fast cooling rate was related to the random orientation of acicular α platelets in BQ/S specimen. Based on the experimental results, the effect of cooling rate on the SCC behavior of β-processed Ti64 alloy in aqueous NaCl solution was discussed.

The origin of the LMC stellar bar: clues from the SFH of the bar and inner disc

NASA Astrophysics Data System (ADS)

Monteagudo, L.; Gallart, C.; Monelli, M.; Bernard, E. J.; Stetson, P. B.

2018-01-01

We discuss the origin of the Large Magellanic Cloud (LMC) stellar bar by comparing the star formation histories (SFHs) obtained from deep colour-magnitude diagrams (CMDs) in the bar and in a number of fields in different directions within the inner disc. The CMDs, reaching the oldest main-sequence turn-offs in these very crowded fields, have been obtained with VIMOS on the Very Large Telescope in the service mode, under very good seeing conditions. We show that the SFHs of all fields share the same patterns, with consistent variations of the star formation rate as a function of time in all of them. We therefore conclude that no specific event of star formation can be identified with the formation of the LMC bar, which instead likely formed from a redistribution of disc material which occurred when the LMC disc became bar unstable, and shared a common SFH with the inner disc thereafter. The strong similarity between the SFH of the centre and edge of the bar rules out the expected significant spatial variations of the SFH across the bar.

Na/Ca exchange in the basolateral membrane of the A6 cell monolayer: role in Cai homeostasis.

PubMed

Brochiero, E; Raschi, C; Ehrenfeld, J

1995-05-01

The presence of a Na/Ca exchanger in A6 cells was investigated by measuring intracellular calcium (Cai) fluctuations and the 45Ca fluxes through the basolateral membranes (blm) of the cell monolayer. Removal of Na+ from the medium produced a transient increase in Cai followed by a regulatory phase returning Cai to control levels in 3-4 min, this phase being greatly accelerated (< 60 s) by NaCl addition (apparent Km of approximately 5 mM Na+). The Cai increase was only found with the Na(+)-free medium on the basolateral side of the cell monolayer. A twofold increase in the 45Ca influx was observed under these conditions. In Ca(2+)- depleted cells, the initial Cai increase after Ca2+ addition to the medium was greater when the putative Na/Ca exchanger was not functioning (i.e. in a Na(+)-free medium). 45Ca effluxes through the blm of the monolayer were greatly and transiently increased by a Na(+)-free medium on the serosal side and blocked by orthovanadate (1 mM). The Cai increased induced by a hypo-osmotic shock was greater in cells bathed in a Na(+)-medium, conditions expected to block the activity of the Na/Ca exchanger. These findings support the hypothesis that a Na/Ca exchanger is present on the blm of A6 cells and affirm its role in Cai homeostasis in steady-state conditions and following osmotic shock. In addition, a Ca2+ pump also located on the blm and Ca2+ stores sensitive to inositol 1,4,5-trisphosphate were found to be implicated in Cai homeostasis.

Electronic Spectra of Cs2NaYb(NO2)6: Is There Quantum Cutting?

PubMed

Luo, Yuxia; Liu, Zhenyu; Hau, Sam Chun-Kit; Yeung, Yau Yuen; Wong, Ka-Leung; Shiu, Kwok Keung; Chen, Xueyuan; Zhu, Haomiao; Bao, Guochen; Tanner, Peter A

2018-05-03

The crystal structure and electronic spectra of the T h symmetry hexanitritoytterbate(III) anion have been studied in Cs 2 NaY 0.96 Yb 0.04 (NO 2 ) 6 , which crystallizes in the cubic space group Fm3̅. The emission from Yb 3+ can be excited via the NO 2 - antenna. The latter electronic transition is situated at more than twice the energy of the former, but at room temperature, one photon absorbed at 470 nm in the triplet state produces no more than one photon emitted. Some degree of quantum cutting is observed at 298 K under 420 nm excitation into the singlet state and at 25 K using excitation into either state. The quantum efficiency is ∼10% at 25 K. The energy level scheme of Yb 3+ has been deduced from excitation and emission spectra and calculated by crystal field theory. New improved energy level calculations are also reported for the Cs 2 NaLn(NO 2 ) 6 (Ln = Pr, Eu, Tb) series using the f- Spectra package. The neat crystal Cs 2 NaYb(NO 2 ) 6 has also been studied, but results were unsatisfactory due to sample decomposition, and this chemical instability makes it unsuitable for applications.

The kaon identification system in the NA62 experiment at CERN

DOE Office of Scientific and Technical Information (OSTI.GOV)

Romano, A.

2015-07-01

The main goal of the NA62 experiment at CERN is to measure the branching ratio of the ultra-rare K{sup +} → π{sup +} ν ν-bar decay with 10% accuracy. NA62 will use a 750 MHz high-energy un-separated charged hadron beam, with kaons corresponding to ∼6% of the beam, and a kaon decay-in-flight technique. The positive identification of kaons is performed with a differential Cherenkov detector (CEDAR), filled with Nitrogen gas and placed in the incoming beam. To stand the kaon rate (45 MHz average) and meet the performances required in NA62, the Cherenkov detector has been upgraded (KTAG) with newmore » photon detectors, readout, mechanics and cooling systems. The KTAG provides a fast identification of kaons with an efficiency of at least 95% and precise time information with a resolution below 100 ps. A half-equipped KTAG detector has been commissioned during a technical run at CERN in 2012, while the fully equipped detector, its readout and front-end have been commissioned during a pilot run at CERN in October 2014. The measured time resolution and efficiency are within the required performances. (authors)« less

Co-transforming bar and CsALDH Genes Enhanced Resistance to Herbicide and Drought and Salt Stress in Transgenic Alfalfa (Medicago sativa L.)

PubMed Central

Duan, Zhen; Zhang, Daiyu; Zhang, Jianquan; Di, Hongyan; Wu, Fan; Hu, Xiaowen; Meng, Xuanchen; Luo, Kai; Zhang, Jiyu; Wang, Yanrong

2015-01-01

Drought and high salinity are two major abiotic factors that restrict the productivity of alfalfa. By application of the Agrobacterium-mediated transformation method, an oxidative responsive gene, CsALDH12A1, from the desert grass Cleistogenes songorica together with the bar gene associated with herbicide resistance, were co-transformed into alfalfa (Medicago sativa L.). From the all 90 transformants, 16 were positive as screened by spraying 1 mL L-1 10% Basta solution and molecularly diagnosis using PCR. Real-time PCR analysis indicated that drought and salt stress induced high CsALDH expression in the leaves of the transgenic plants. The CsALDH expression levels under drought (15 d) and salt stress (200 mM NaCl) were 6.11 and 6.87 times higher than in the control plants, respectively. In comparison to the WT plants, no abnormal phenotypes were observed among the transgenic plants, which showed significant enhancement of tolerance to 15 d of drought and 10 d of salinity treatment. Evaluation of the physiological and biochemical indices during drought and salt stress of the transgenic plants revealed relatively lower Na+ content and higher K+ content in the leaves relative to the WT plants, a reduction of toxic on effects and maintenance of osmotic adjustment. In addition, the transgenic plants could maintain a higher relative water content level, higher shoot biomass, fewer changes in the photosystem, decreased membrane injury, and a lower level of osmotic stress. These results indicate that the co-expression of the introduced bar and CsALDH genes enhanced the herbicide, drought and salt tolerance of alfalfa and therefore can potentially be used as a novel genetic resource for the future breeding programs to develop new cultivars. PMID:26734025

BaBar Experiment Public Web Site

Science.gov Websites

spotlights BaBar time-reversal measurement. December 14, 2012 PhysicsWorld.com has selected the BaBar time . BaBar Makes First Direct Observation of Time-Reversal Violation August 30, 2012 Fundamental interactions among particles are oblivious to the direction of time (a movie of a rock thrown up and falling back

Influence of the weighing bar size to determine optimal time of biodiesel-glycerol separation by using the buoyancy weighing-bar method

NASA Astrophysics Data System (ADS)

Tambun, R.; Sibagariang, Y.; Manurung, J.

2018-02-01

The buoyancy weighing-bar method is a novel method in the particle size distribution measurement. This method can measure particle size distributions of the settling particles and floating particles. In this study, the buoyancy weighing-bar method is applied to determine optimal time of biodiesel-glycerol separation. The buoyancy weighing-bar method can be applied to determine the separation time because biodiesel and glycerol have the different densities. The influences of diameter of weighing-bar by using the buoyancy weighing-bar method would be experimentally investigated. The diameters of weighing-bar in this experiment are 8 mm, 10 mm, 15 mm and 20 mm, while the graduated cylinder (diameter : 65 mm) is used as vessel. The samples used in this experiment are the mixture of 95 % of biodiesel and 5 % of glycerol. The data obtained by the buoyancy weighing-bar method are analized by using the gas chromatography to determine the purity of biodiesel. Based on the data obtained, the buoyancy weighing-bar method can be used to detect the separation time of biodiesel-glycerol by using the weighing-bar diameter of 8 mm, 10 mm, 15 mm and 20 mm, but the most accuracy in determination the biodiesel-glycerol separation time is obtained by using the weighing-bar diameter of 20 mm. The biodiesel purity of 97.97 % could be detected at 64 minutes by using the buoyancy weighing-bar method when the weighing-bar diameter of 20 mm is used.

Correlation of Selected Subsize Charpy Bars versus the Standard Charpy Bar

DTIC Science & Technology

1958-05-01

WAL TR 112/91 TECIINICAL REPORT r- i -I WATERTOWN ARSENAL LABORATORI ES CORRELATION OF SELECTED SUBSIZE CHARPY BARS VERSUS THE STANDARD CHARPY BAR...DTIC BY fitELECTED CHARLES Ht. CURIL MAY 8 19813 GEORGE M. OR14ER 0.0. PROJECT: INDUSTRIAL PREPAREDNESS MEASURE, ,... DEVELOPMENT OF SUBSIZE CHARPY ...STANDARD P.E.S.D. NO.: 60302l281-16-65003 REPORT NO.: WAL TR 112191 FILING SUBJECT: SUBSIZE CHARPY IThis documnt~ has mo f1 P~ub1c teT -rie and mczlelIN

Evaluation of longitudinal joint tie bar system.

DOT National Transportation Integrated Search

2011-09-01

"An adequate longitudinal joint tie bar system is essential in the overall performance of concrete pavement. Excessive : longitudinal joint openings are believed to be caused by either inadequate tie bar size or spacing or improper tie bar : installa...

Crystal structure of a new variety of lead dodecaborate Pb{sub 6}(Li{sub 0.65}Na{sub 0.19})[B{sub 12}O{sub 24}]I{sub 0.84} {center_dot} 0.168H{sub 2}O and its comparison with beryl and cordierite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Belokoneva, E. L., E-mail: elbel@geol.msu.ru; Derkach, I. K.; Dimitrova, O. V.

2013-05-15

Crystals of a new representative of ring-radical dodecaborates Pb{sub 6}(Li{sub 0.65}Na{sub 0.19})[B{sub 12}O{sub 24}]I{sub 0.84} {center_dot} 0.168H{sub 2}O, space group R3bar m , are obtained under hydrothermal conditions. The structure is determined with-out preliminary knowledge of the chemical formula. It is close to that of the Pb{sub 6}[B{sub 12}O{sub 24}] {center_dot} H{sub 2}O dodecaborate studied earlier, but unlike the latter structure it contains admixtures of iodide anion, lithium cation, and water molecule, which incompletely populate positions in channels. The formation of the second variety, which brings to light ion-exchange properties of the crystals, is due to mineralizing ions available inmore » the concen-trated solution in the course of crystallization. The new compound is compared with beryl and cordierite, which have close structures with channels capable of capturing various groups. Structures of synthetic Na and Ag dodecaborates with analogous but distorted ring dodecaborate radicals are discussed.« less

Evaluation of a nontoxic rigid polymer as connecting bar in external skeletal fixators.

PubMed

Störk, Christoph K; Canivet, Philippe; Baidak, Alexandre A; Balligand, Marc H

2003-01-01

To investigate the mechanical characteristics of a nontoxic, low-cost, rigid polymer (RP) and to compare the structural and mechanical properties of a full-frame external skeletal fixator (ESF) with either RP connecting bars, polymethylmethacrylate (PMMA) connecting bars, or stainless-steel (SS) clamps and connecting bars. In vitro mechanical evaluation. Mechanical properties were assessed using an in vitro bone fracture model with a bilateral uniplanar ESF (type II). Identical ESF were built with connecting bars using RP (n = 8), PMMA (n = 8), and SS connecting bars and clamps (System Meynard; n = 3). Nondestructive mechanical tests were performed in uniaxial compression (AC) and craniocaudal (CC) 4-point bending, as well as fatigue AC. Composite stiffness for each specimen and for each loading mode was calculated from 6 replicate measures using the slope of the load displacement curve at small displacements. RP, PMMA, and SS ESF constructs yielded mean +/- SD composite stiffness values of 227 +/- 15, 381 +/- 30, and 394 +/- 9 N/mm in AC and of 35 +/- 2, 24 +/- 2, and 15 +/- 0 N/mm in CC, respectively. Structural and mechanical properties of RP are satisfactorily rigid and fatigue resistant for its use as a connecting bar in ESF. RP connecting bars in an ESF are a reliable, versatile, nontoxic and inexpensive option for the veterinary surgeon. Copyright 2003 by The American College of Veterinary Surgeons

Changes in Georgia restaurant and bar smoking policies from 2006 to 2012.

PubMed

Chandora, Rachna D; Whitney, Carrie F; Weaver, Scott R; Eriksen, Michael P

2015-05-14

The purpose of this study is to examine the change in smoking policy status among Georgia restaurants and bars from 2006 to 2012 and to identify restaurant and bar characteristics that are associated with allowing smoking. Data were obtained from similar cross-sectional indoor air surveys conducted in 2006 and 2012 in Georgia. Both surveys were designed to gather information about restaurant and bar smoking policies. Weighted χ(2) analyses were performed to identify changes in smoking policy status and other variables from 2006 to 2012. Weighted logistic regression analysis was used to test for significant associations between an establishment's smoking policy and other characteristics. The percentage of restaurants and bars in Georgia that allowed smoking nearly doubled, from 9.1% in 2006 to 17.6% in 2012. The analyses also showed a significant increase in the percentage of establishments that allow smoking when minors are present. Having a liquor license was a significant predictor of allowing smoking. The Smokefree Air Act was enacted in 2005 to protect the health and welfare of Georgia citizens, but study results suggest that policy makers should reevaluate the law and consider strengthening it to make restaurants and bars 100% smokefree without exemptions.

Crystal Growth and Scintillation Properties of $${\\rm Cs}_{2}{\\rm NaGdBr}_{6}{:}{\\rm Ce}^{3+}$$

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Pin; Zhou, Xiaowang; Deng, Haoran

2013-04-02

Single crystals of Cs 2NaGdBr 6 with different Ce +3 activator concentrations were grown by a two-zone Bridgman method. This new compound belongs to a large elpasolite halide (A 2BLnX 6) family. Many of these elpasolite compounds have shown high luminosity, good energy resolution and excellent proportionality in comparison to traditional scintillators such as CsI and NaI; therefore, they are particularly attractive for gamma-ray spectroscopy applications. This study investigated the scintillator properties of Cs 2NaGdBr 6:Ce +3 crystals as a new material for radiation detection. Special focus has been placed on the effects of activator concentration (0 to 50 mol.%)more » on the photoluminescence responses. Results of structural refinement, photoluminescence, radioluminescence, lifetime and proportionality measurements for this new compound are reported.« less

Direct measurement of CO2 solubility and pH in NaCl hydrothermal solutions by combining in-situ potentiometry and Raman spectroscopy up to 280 °C and 150 bar

NASA Astrophysics Data System (ADS)

Truche, Laurent; Bazarkina, Elena F.; Berger, Gilles; Caumon, Marie-Camille; Bessaque, Gilles; Dubessy, Jean

2016-03-01

The in-situ monitoring of aqueous solution chemistry at elevated temperatures and pressures is a major challenge in geochemistry. Here, we combined for the first time in-situ Raman spectroscopy for concentration measurements and potentiometry for pH measurement in a single hydrothermal cell equipped with sampling systems and operating under controlled conditions of temperature and pressure. Dissolved CO2 concentration and pH were measured at temperatures up to 280 °C and pressures up to 150 bar in the H2O-CO2 and H2O-CO2-NaCl systems. A Pitzer specific-ion-interaction aqueous model was developed and confirmed the accuracy and consistency of the measurements, at least up to 250 °C. The revised Pitzer parameters for the H2O-CO2-NaCl system were formatted for the Phreeqc geochemical software. Significant changes with respect to the Pitzer.dat database currently associated with Phreeqc were observed. The new model parameters are now available for further applications. The Raman and pH probes tested here may also be applied to field monitoring of hydrothermal springs, geothermal wells, and oil and gas boreholes.

A Kinematic Link Between Boxy Bulges, Stellar Bars, and Nuclear Activity in NGC 3079 and NGC 4388

NASA Technical Reports Server (NTRS)

Veilleux, S.; Bland-Hawthrorn, J.; Cecil, Gerald

1999-01-01

We present direct kinematic evidence for bar streaming in two active galaxies with boxy stellar bulges. The Hawaii Imaging Fabry-Perot Interferometer was used on the Canada-France-Hawaii 3.6-m telescope and the University of Hawaii 2.2-m telescope to derive the two-dimensional velocity field of the line-emitting gas in the disks of the Sc galaxy NGC 3079 and the Sb galaxy NGC 4388. In contrast to previous work based on long-slit data, the detection of the bar potential from the Fabry-Perot data does not rely on the existence of inner Lindblad resonances or strong bar-induced shocks. Simple kinematic models which approximate the intrinsic gas orbits as nonintersecting, inclined elliptical annuli that conserve angular momentum characterize the observed velocity fields. In NGC 3079, bar streaming motions with moderately eccentric orbits (e = b/a approx. 0.7) aligned along PA = 130 deg. intrinsic to the disk (PA = 97 deg. on the sky) are detected out to R(sub b) = 3.6 kpc. The orbits become increasingly circular beyond that radius (e = 1 at R(sub d) approx. = 6 kpc). The best model for NGC 4388 includes highly eccentric orbits (e approx. 0.3) for R(sub) less than or equal to 1.5 kpc which are aligned along PA = 135 deg. intrinsic to the disk (PA = 100 deg. on the sky). The observed "spiral arms" are produced by having the orbits become increasingly circular from the ends of the bar to the edge of the disk (R(sub d) approx. = 5 kpc), and the intrinsic bar PA shifting from 135 deg. to 90 deg.. Box-shaped bulges in both NGC 3079 and NGC 4388 are confirmed using new near-infrared images to reduce dust obscuration. Morphological analysis of starlight in these galaxies is combined with the gas kinematics derived from the Fabry-Perot spectra to test evolutionary models of stellar bars that involve transitory boxy bulges, and to quantify the importance of such bars in fueling active nuclei. Our data support the evolutionary bar models, but fail to prove convincingly that the

The e{sup +}e{sup -}{yields}J/{psi}DD-bar, J/{psi}DD-bar* reactions with dynamically generated resonances

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gamermann, D.; Oset, E.

2008-08-31

In two recent reactions by Belle producing DD-bar and DD-bar* meson pairs, peaks above threshold have been measured in the differential cross sections, possibly indicating new resonances in these channels. We want to study such reactions from the point of view that the D meson pairs are produced from already known or predicted resonances below threshold. Our study shows that the peak in the DD-bar* production is not likely to be caused by the X(3872) resonance, but the peak seen in DD-bar invariant mass can be well described if the DD-bar pair comes from the already predicted scalar X(3700) resonance.

Effect of flaxseed flour incorporation on the physical properties and consumer acceptability of cereal bars.

PubMed

Khouryieh, H; Aramouni, F

2013-12-01

Extensive research has revealed numerous nutritional and health benefits of flaxseed due primarily to its nutrients content. The objective of this study was to evaluate the effect of flaxseed flour addition on the physical and sensory characteristics of cereal bars. Four formulations of the flaxseed cereal bars were prepared by partially replacing oats with flaxseed flour added at levels of 0 (control), 6%, 12% and 18%. There were no significant differences (p > 0.05) in water activity, moisture and firmness values between the flaxseed bars and control. Flaxseed addition significantly (p < 0.05) decreased lightness and increased redness of the bars. There were no significant differences (p > 0.05) between the 12% flax cereal bars and the control with respect to sensory attributes and overall acceptability. The overall acceptability for both 12% flax bars and the control was in between 'like moderately' and 'like slightly' on the 9-point hedonic scale. The overall acceptability was most highly correlated with flavor acceptability for both control (r = 0.80) and 12% flax (r = 0.82) cereal bars. Flaxseed bars provided 12% dietary fiber of the daily recommended value. These results indicated that flaxseed flour incorporation up to 12% substantially enhanced the nutritional qualities of the cereal bars without affecting their sensory and quality properties.

Density of states, optical and thermoelectric properties of perovskite vanadium fluorides Na3VF6

NASA Astrophysics Data System (ADS)

Reshak, A. H.; Azam, Sikander

2014-05-01

The electronic structure, charge density and Fermi surface of Na3VF6 compound have been examined with the support of density functional theory (DFT). Using the full potential linear augmented plane wave method, we employed the local density approximation (LDA), generalized gradient approximation (GGA) and Engel-Vosko GGA (EVGGA) to treat the exchange correlation potential to solve Kohn-Sham equations. The calculation show that Na3VF6 compound has metallic nature and the Fermi energy (EF) is assessed by overlapping of V-d state. The calculated density of states at the EF are about 18.655, 51.932 and 13.235 states/eV, and the bare linear low-temperature electronic specific heat coefficient (γ) is found to be 3.236 mJ/mol-K2, 9.008 mJ/mol-K2 and 2.295 mJ/mol-K2 for LDA, GGA and EVGGA, respectively. The Fermi surface is composed of two sheets. The chemical bonding of Na3VF6 compound is analyzed through the electronic charge density in the (1 1 0) crystallographic plane. The optical constants and thermal properties were also calculated and discussed.

Barred Ring Galaxy NGC 1291

NASA Image and Video Library

2005-05-05

This ultraviolet image left and visual image right from NASA Galaxy Evolution Explorer is of the barred ring galaxy NGC 1291. The VIS image is dominated by the inner disk and bar. The UV image is dominated by the low surface brightness outer arms.

Spectral narrowing of a 980 nm tapered diode laser bar

NASA Astrophysics Data System (ADS)

Vijayakumar, Deepak; Jensen, Ole Bjarlin; Lucas Leclin, Ga"lle; Petersen, Paul Michael; Thestrup, Birgitte

2011-03-01

High power diode laser bars are interesting in many applications such as solid state laser pumping, material processing, laser trapping, laser cooling and second harmonic generation. Often, the free running laser bars emit a broad spectrum of the order of several nanometres which limit their scope in wavelength specific applications and hence, it is vital to stabilize the emission spectrum of these devices. In our experiment, we describe the wavelength narrowing of a 12 element 980 nm tapered diode laser bar using a simple Littman configuration. The tapered laser bar which suffered from a big smile has been "smile corrected" using individual phase masks for each emitter. The external cavity consists of the laser bar, both fast and slow axis micro collimators, smile correcting phase mask, 6.5x beam expanding lens combination, a 1200 lines/mm reflecting grating with 85% efficiency in the first order, a slow axis focusing cylindrical lens of 40 mm focal length and an output coupler which is 10% reflective. In the free running mode, the laser emission spectrum was 5.5 nm wide at an operating current of 30A. The output power was measured to be in excess of 12W. Under the external cavity operation, the wavelength spread of the laser could be limited to 0.04 nm with an output power in excess of 8 W at an operating current of 30A. The spectrum was found to be tuneable in a range of 16 nm.

Tidally Induced Bars of Galaxies in Clusters

NASA Astrophysics Data System (ADS)

Łokas, Ewa L.; Ebrová, Ivana; del Pino, Andrés; Sybilska, Agnieszka; Athanassoula, E.; Semczuk, Marcin; Gajda, Grzegorz; Fouquet, Sylvain

2016-08-01

Using N-body simulations, we study the formation and evolution of tidally induced bars in disky galaxies in clusters. Our progenitor is a massive, late-type galaxy similar to the Milky Way, composed of an exponential disk and a Navarro-Frenk-White dark matter halo. We place the galaxy on four different orbits in a Virgo-like cluster and evolve it for 10 Gyr. As a reference case, we also evolve the same model in isolation. Tidally induced bars form on all orbits soon after the first pericenter passage and survive until the end of the evolution. They appear earlier, are stronger and longer, and have lower pattern speeds for tighter orbits. Only for the tightest orbit are the properties of the bar controlled by the orientation of the tidal torque from the cluster at pericenter. The mechanism behind the formation of the bars is the angular momentum transfer from the galaxy stellar component to its halo. All of the bars undergo extended periods of buckling instability that occur earlier and lead to more pronounced boxy/peanut shapes when the tidal forces are stronger. Using all simulation outputs of galaxies at different evolutionary stages, we construct a toy model of the galaxy population in the cluster and measure the average bar strength and bar fraction as a function of clustercentric radius. Both are found to be mildly decreasing functions of radius. We conclude that tidal forces can trigger bar formation in cluster cores, but not in the outskirts, and thus can cause larger concentrations of barred galaxies toward the cluster center.

High-pressure systematic of NaMe3+Si2O6 pyroxenes: volume compression vs Me3+ cation radius

NASA Astrophysics Data System (ADS)

Periotto, Benedetta; Nestola, Fabrizio; Balic-Zunic, Tonci; Pasqual, Daria; Alvaro, Matteo; Ohashi, Haruo

2010-05-01

Recent investigations have been experimentally demonstrated that Na-clinopyroxenes (Na-cpx) can be stable throughout a wide range of temperatures and pressures in the upper mantle and several works have been carried out in order to better constrain their physical properties. In this work the equation of state of a synthetic NaInSi2O6 clinopyroxene characterized by a trivalent non 3d-transition metal at the Me3+ crystallographic site (space group C2/c) was determined up to about 8 GPa by in situ single-crystal X-ray diffraction. Since previous investigations on CaMe2+Si2O6 showed a different effect when 3d- and non 3d-transition elements located at Me site, the aim of this study is to provide a definitive model capable to predict the high-pressure behaviour of (Ca,Na)(Me2+, Me3+)Si2O6 clinopyroxenes. A single crystal of NaInSi2O6 with size 150*80*50 microns3 was selected for the high-pressure single-crystal X-ray diffraction study. The sample was loaded in an ETH-type diamond anvil cell assembled with a diamond culet of 600 microns in diameter and a gasket preindented to 90 microns with a spark eroded hole of 200 microns in diameter. The cpx was loaded together with a single-crystal of quartz used as an internal pressure standard and some ruby chips used for more approximate determination of the internal pressure. The measurements were performed using a four-circles STOE STADI IV diffractometer on which the software SINGLE08 has been recently installed allowing to perform the eight-position diffracted-beam centering and to fit the diffraction peak profiles. Such centering procedure allows to obtain precise and accurate unit-cell parameters in order to provide values of room pressure bulk modulus affected by a significantly small error. The NaInSi2O6 cpx was investigated at 12 different pressures up to 7.83 GPa. No evidences of phase transformation were found throughout the pressure range investigated. The sample compresses anisotropically with the b direction being

Scanning electron microscopy observations of failures of implant overdenture bars: a case series report.

PubMed

Waddell, J Neil; Payne, Alan G T; Swain, Michael V; Kieser, Jules A

2010-03-01

Soldered or cast bars are used as a standard of care in attachment systems supporting maxillary and mandibular implant overdentures. When failures of these bars occur, currently there is a lack of evidence in relation to their specific etiology, location, or nature. To investigate the failure process of a case series of six failed soldered bars, four intact soldered bars, and one intact cast milled bar, which had been supporting implant overdentures. A total of 11 different overdenture bars were removed from patients with different configuration of opposing arches. A failed bar (FB) group (n = 6) had failed soldered overdenture bars, which were recovered from patients following up to 2 years of wear before requiring prosthodontic maintenance and repair. An intact bar (IB) group (n = 5) had both soldered bars and a single cast milled bar, which had been worn by patients for 2 to 5 years prior to receiving other aspects of prosthodontic maintenance. All bars were examined using scanning electron microscopy to establish the possible mode of failure (FB) or to identify evidence of potential failure in the future (IB). Evidence of a progressive failure mode of corrosion fatigue and creep were observed on all the FB and IB usually around the solder areas and nonoxidizing gold cylinder. Fatigue and creep were also observed in all the IB. Where the level of corrosion was substantial, there was no evidence of wear from the matrices of the attachment system. Evidence of an instantaneous failure mode, ductile and brittle overload, was observed on the fracture surfaces of all the FB, within the solder and the nonoxidizing gold cylinders, at the solder/cylinder interface. Corrosion, followed by corrosion fatigue, appears to be a key factor in the onset of the failure process for overdenture bars in this case series of both maxillary and mandibular overdentures. Limited sample size and lack of standardization identify trends only but prevent broad interpretation of the findings.

On the Bar Pattern Speed Determination of NGC 3367

NASA Astrophysics Data System (ADS)

Gabbasov, R. F.; Repetto, P.; Rosado, M.

2009-09-01

An important dynamic parameter of barred galaxies is the bar pattern speed, Ω P . Among several methods that are used for the determination of Ω P , the Tremaine-Weinberg method has the advantage of model independence and accuracy. In this work, we apply the method to a simulated bar including gas dynamics and study the effect of two-dimensional spectroscopy data quality on robustness of the method. We added white noise and a Gaussian random field to the data and measured the corresponding errors in Ω P . We found that a signal to noise ratio in surface density ~5 introduces errors of ~20% for the Gaussian noise, while for the white noise the corresponding errors reach ~50%. At the same time, the velocity field is less sensitive to contamination. On the basis of the performed study, we applied the method to the NGC 3367 spiral galaxy using Hα Fabry-Pérot interferometry data. We found Ω P = 43 ± 6 km s-1 kpc-1 for this galaxy.

Splash bar for cooling tower fill assembly

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stackhouse, D.W.; Heidl, S.C.

1987-11-10

A crossflow cooling tower fill assembly for allowing liquid to fall down through the fill assembly and for allowing cooling air to flow through the fill assembly transverse to the flow of the liquid in order to cool the liquid is described. The assembly comprises: longitudinal splash bars; and means for supporting the splash bars so that the splash bars are substantially horizontal and parallel to one another and arranged in vertically spaced, substantially horizontal planes. The splash bars in each plane are horizontally spaced from one another to allow the liquid to fall down between the splash bars tomore » the planes of splash bars below. Each splash bar includes a substantially horizontal, longitudinally extending top web member having (1) longitudinally extending, downwardly projecting vertical side web members, both of the side web members having a lower longitudinal edge with a longitudinally extending, inwardly projecting flange, and (2) at least one longitudinally extending, downardly projecting rib web member between the side web members. Each rib web member has a lower longitudinal edge with a longitudinally extending, laterally projecting flange.« less

[Cereal bars with soy protein and wheat germ, physicochemical characteristics and texture during the storage].

PubMed

Castro Freitas, Daniela D G

2005-09-01

Studies analyzing cereal bars have reported on consumer characteristics and preferences in sensory analyses and on their market growth, however little has been published on their physicochemical data and texture properties. Thus the objective of this research was to provide information about the storage of a cereal bar formulation with high protein and vitamin levels based on soy protein and wheat germ, packaged in 3 different films (A: PET/PEBD; B: PETmet/PEBD; C: PET/PEBD/AL/PEBD), during 6 months under environmental conditions of temperature (25 +/- 2 degrees C) and relative humidity (56%). The moisture content, water activity, pH and total acidity of the cereal bars were determined. The textural measurements accompanied during storage were breaking strength, hardness and cohesiveness. The cereal bars presented variations in water activity (Aw), moisture content and total acidity during storage. The moisture content of the bars tended to increase, which led to a significant (p = 0.05) influence on the texture characteristics of breaking strength and hardness, in the different packaging films tested. The increase in the values for breaking strength (A: 4756,5N; B: 5093,0N; C: 5575,6N) at 45 days of storage was attributed to a possible crystallization of the agglutinating syrup used for the bars. The textured soy protein used in the formulation could also have contributed to this fact due to its hygroscopic character, also interfering in the decrease in the cohesiveness measurements (deformation) with time. The effect of the different barrier properties of the packaging films tested was significant (p < 0.05) in the stability of the cereal bars during storage.

Cold dust in the giant barred galaxy NGC 1365

NASA Astrophysics Data System (ADS)

Tabatabaei, F. S.; Weiß, A.; Combes, F.; Henkel, C.; Menten, K. M.; Beck, R.; Kovács, A.; Güsten, R.

2013-07-01

Constraining the physcial properties of dust requires observations at submm wavelengths. This will provide important insight into the gas content of galaxies. We mapped NGC 1365 at 870 μm with LABOCA, the Large APEX Bolometer Camera, allowing us to probe the central mass concentration as well as the rate at which the gas flows to the center. We obtained the dust physical properties both globally and locally for different locations in the galaxy. A 20 K modified black body represents about 98% of the total dust content of the galaxy, the rest can be represented by a warmer dust component of 40 K. The bar exhibits an east-west asymmetry in the dust distribution: The eastern bar is heavier than the western bar by more than a factor of 4. Integrating the dust spectral energy distribution, we derived a total infrared luminosity, LTIR, of 9.8 × 1010 L⊙, leading to a dust-enshrouded star formation rate of SFRTIR ≃ 16.7 M⊙ yr-1 in NGC 1365. We derived the gas mass from the measurements of the dust emission, resulting in a CO-to-H2 conversion factor of XCO ≃ 1.2 × 1020 mol cm-2 (K km s-1)-1 in the central disk, including the bar. Taking into account the metallicity variation, the central gas mass concentration is only ≃20% at R < 40″ (3.6 kpc). On the other hand, the timescale on which the gas flows into the center, ≃300 Myr, is relatively short. This indicates that the current central mass in NGC 1365 is evolving fast because of the strong bar.

Social Organization in Bars: Implications for Tobacco Control Policy

PubMed Central

Lee, Juliet P.; Antin, Tamar M.J.; Moore, Roland S.

2011-01-01

This paper considers social roles and relationships of the patrons, staff and owners of bars as critical factors determining adherence to public health policies, and specifically California’s smokefree workplace law. Specific elements of social organization in bars affecting health policy include the community within which the bar is set, the unique identity the bar creates, the bar staff and patrons who enact this identity, and their bar society. These elements were found to contribute to the development of power relations within the bar and solidarity against the outside world, resulting in either resistance to or compliance with smokefree workplace policy. PMID:22522904

Understanding the conductive channel evolution in Na:WO(3-x)-based planar devices.

PubMed

Shang, Dashan; Li, Peining; Wang, Tao; Carria, Egidio; Sun, Jirong; Shen, Baogen; Taubner, Thomas; Valov, Ilia; Waser, Rainer; Wuttig, Matthias

2015-04-14

An ion migration process in a solid electrolyte is important for ion-based functional devices, such as fuel cells, batteries, electrochromics, gas sensors, and resistive switching systems. In this study, a planar sandwich structure is prepared by depositing tungsten oxide (WO(3-x)) films on a soda-lime glass substrate, from which Na(+) diffuses into the WO(3-x) films during the deposition. The entire process of Na(+) migration driven by an alternating electric field is visualized in the Na-doped WO(3-x) films in the form of conductive channel by in situ optical imaging combined with infrared spectroscopy and near-field imaging techniques. A reversible change of geometry between a parabolic and a bar channel is observed with the resistance change of the devices. The peculiar channel evolution is interpreted by a thermal-stress-induced mechanical deformation of the films and an asymmetric Na(+) mobility between the parabolic and the bar channels. These results exemplify a typical ion migration process driven by an alternating electric field in a solid electrolyte with a low ion mobility and are expected to be beneficial to improve the controllability of the ion migration in ion-based functional devices, such as resistive switching devices.

Minimally invasive repair of symmetric pectus carinatum: bilateral thoracoscopic chondrotomies and suprasternal compression bar placement.

PubMed

Bell, Robert; Idowu, Olajire; Kim, Sunghoon

2012-11-01

We previously reported a novel minimally invasive repair for unilateral pectus carinatum. We have now modified this approach for the repair of symmetric bilateral pectus carinatum. Using thoracoscopy, parasternal chondrotomies were performed at multiple rib levels at points of maximal sternal protrusion. The sternum was depressed to an appropriate position and maintained using a suprasternal metal compression bar. The bar was applied in a submuscular plane and anchored to the lateral ribs with sutures. Bars were removed after 6 months. Three patients with severe symmetric pectus carinatum underwent the repair. The first patient returned to the operating room after 1 month for repeat fixation of the bar after suture breakage. No other complications occurred. Operative times were comparable to published series. Patient satisfaction after the repair was good. Minimally invasive thoracoscopic repair of symmetric pectus carinatum using chondrotomies and suprasternal bar compression is a feasible alternative to open repair.

An Assessment of Health Risks and Mortality from Exposure to Secondhand Smoke in Chinese Restaurants and Bars

PubMed Central

Liu, Ruiling; Jiang, Yuan; Li, Qiang; Hammond, S. Katharine

2014-01-01

Introduction Smoking is generally not regulated in restaurants or bars in China, or the restrictions are not fully implemented if there are any, while the related hazard health effects are not recognized by the majority of the Chinese population. Objectives This study aims to assess the excess health risks and mortality attributed to secondhand smoke (SHS) exposure in restaurants and bars for both servers and patrons to provide necessary evidence for advancing tobacco control in this microenvironment. Methods Two approaches were used for the assessment. One is a continuous approach based on existing field measurements and Repace and Lowrey’s dose-response model, and the other is a categorical approach based on exposure or not and epidemiological studies. Results Based on the continuous approach, servers were estimated to have a lifetime excess risk (LER) of lung cancer death (LCD) of 730 to 1,831×10−6 for working five days a week for 45 years in smoking restaurants and 1,862 to 8,136×10−6 in smoking bars, and patrons could have a LER of LCD of 47 to 117×10−6 due to visiting smoking restaurants for an average of 13 minutes a day for 60 years, and 119 to 522×10−6 due to visiting smoking bars. The categorical approach estimated that SHS exposure in restaurants and bars alone caused 84 LCD and 57 ischemic heart disease (IHD) deaths among nonsmoking servers and 1,2419 LCDs and 1,689 IHD deaths among the nonsmoking patron population. Conclusions SHS exposure in restaurants and bars alone can impose high lifetime excess risks of lung cancer death and ischemic heart disease deaths to both servers and patrons, and can cause a significant number of deaths each year in China. These health risks and deaths can be prevented by banning smoking in restaurants and bars and effectively implementing these smoking bans. PMID:24416289

The efficacy of daily snack replacement with oligofructose-enriched granola bars in overweight and obese adults: a 12-week randomised controlled trial.

PubMed

Pol, Korrie; de Graaf, Cees; Meyer, Diederick; Mars, Monica

2018-05-01

Oligofructose is a prebiotic dietary fibre obtained from chicory root inulin. Oligofructose supplementation may affect satiety, food intake, body weight and/or body composition. The aim was to examine the efficacy of oligofructose-supplemented granola bars on the following weight management outcomes: satiety, energy intake, body weight and body composition in overweight or obese adults. In all, fifty-five adults with overweight or obesity (thirty-six females/nineteen males; age: 41 (sd 12) years; 90·6 (sd 11·8) kg; BMI: 29·4 (sd 2·6) kg/m2) participated in a parallel, triple-blind, placebo-controlled intervention. A total of twenty-nine subjects replaced their snacks twice a day with an equienergetic granola bar supplemented with 8 g of oligofructose (OF-Bar). Subjects in the control group (n 26) replaced their snack with a control granola bar without added oligofructose (Co-Bar). Satiety, 24-h energy intake, body weight and body composition (fat mass and waist circumference) were measured at baseline, weeks 6 and 12. In addition, weekly appetite and gastrointestinal side effects were measured. During the intervention, energy intake, body weight and fat mass remained similar in the Co-Bar and OF-Bar groups (all P>0·05). Both groups lost 0·3 (sd 1·2) kg lean mass (P<0·01) and reduced their waist circumference with -2·2 (sd 3·6) cm (P<0·0001) after 12 weeks. The OF-Bar group reported decreased hunger in later weeks of the intervention (P=0·04), less prospective food consumption (P=0·03) and less thirst (P=0·003). To conclude, replacing daily snacks for 12 weeks with oligofructose-supplemented granola bars does not differentially affect energy intake, body weight and body composition compared with a control bar. However, there was an indication that appetite was lower after oligofructose bar consumption.

Positioning bars for large wire harnesses

NASA Technical Reports Server (NTRS)

Glessner, J. R.

1978-01-01

By tying positioning bars to harness, its configuration can be preserved during transport, thus facilitating installation. Harness can also be showed temporarily by placing hanging hooks on end of bar.

A within-subject comparison of mandibular long-bar and hybrid implant-supported prostheses: evaluation of masticatory function.

PubMed

Tang, L; Lund, J P; Taché, R; Clokie, C M; Feine, J S

1999-09-01

Sixteen edentulous subjects participated in a within-subject crossover clinical trial to test the hypotheses that a long-bar overdenture attached to 4 implants gives greater patient satisfaction and masticatory efficiency than a two-implant hybrid overdenture. All subjects were given a new maxillary conventional denture. Ten received mandibular long-bar overdentures first and six the hybrid overdentures. Two months later, psychometric assessments and functional tests were repeated 3 times at one-week intervals. The mandibular prosthesis was then changed, and recordings were repeated after another 2 months. Mandibular movements and electromyographic activity of jaw muscles were recorded while subjects chewed standard-sized pieces of 5 foods: bread, cheese, apple, sausage, and carrot. Measurements included masticatory time, cleaning time (the time between the end of mastication and the last swallow), and duration and amplitude of masticatory cycles and phases. Multilevel analyses were performed. No significant differences in masticatory time were found between prostheses for any test food. However, cleaning time for carrot [estimated mean of difference (delta) +/- SE: 1.6 sec +/- 0.7] and bread (delta = 1.0 sec +/- 0.4) was slightly but significantly longer for subjects wearing long-bar overdentures. Cycle duration was longer with the long-bar overdenture only for subjects chewing carrot. The opening phase was shorter and the closing phase longer with the long-bar overdenture for almost all test foods. Vertical amplitude was significantly less with the long-bar overdenture for cheese (delta = -2.6 mm +/- 1.1), apple (delta = -2.6 mm +/- 1.0), and sausage (delta = -2.9 mm +/- 1.3). These results suggest that mastication with the 2 prostheses is equally efficient, although clearance of some foods from the mouth is longer with the long-bar overdentures. They also indicate that patients adapt their masticatory movements to the characteristics of different prostheses.

Practical guide to bar coding for patient medication safety.

PubMed

Neuenschwander, Mark; Cohen, Michael R; Vaida, Allen J; Patchett, Jeffrey A; Kelly, Jamie; Trohimovich, Barbara

2003-04-15

Bar coding for the medication administration step of the drug-use process is discussed. FDA will propose a rule in 2003 that would require bar-code labels on all human drugs and biologicals. Even with an FDA mandate, manufacturer procrastination and possible shifts in product availability are likely to slow progress. Such delays should not preclude health systems from adopting bar-code-enabled point-of-care (BPOC) systems to achieve gains in patient safety. Bar-code technology is a replacement for traditional keyboard data entry. The elements of bar coding are content, which determines the meaning; data format, which refers to the embedded data and symbology, which describes the "font" in which the machine-readable code is written. For a BPOC system to deliver an acceptable level of patient protection, the hospital must first establish reliable processes for a patient identification band, caregiver badge, and medication bar coding. Medications can have either drug-specific or patient-specific bar codes. Both varieties result in the desired code that supports patient's five rights of drug administration. When medications are not available from the manufacturer in immediate-container bar-coded packaging, other means of applying the bar code must be devised, including the use of repackaging equipment, overwrapping, manual bar coding, and outsourcing. Virtually all medications should be bar coded, the bar code on the label should be easily readable, and appropriate policies, procedures, and checks should be in place. Bar coding has the potential to be not only cost-effective but to produce a return on investment. By bar coding patient identification tags, caregiver badges, and immediate-container medications, health systems can substantially increase patient safety during medication administration.

33 CFR 110.130 - Bar Harbor, Maine.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Bar Harbor, Maine. 110.130... ANCHORAGE REGULATIONS Anchorage Grounds § 110.130 Bar Harbor, Maine. (a) Anchorage grounds. (1) Anchorage “A” is that portion of Frenchman Bay, Bar Harbor, ME enclosed by a rhumb line connecting the following...

21 CFR 886.5800 - Ophthalmic bar reader.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Ophthalmic bar reader. 886.5800 Section 886.5800...) MEDICAL DEVICES OPHTHALMIC DEVICES Therapeutic Devices § 886.5800 Ophthalmic bar reader. (a) Identification. An ophthalmic bar reader is a device that consists of a magnifying lens intended for use by a...

Deciphering the BAR code of membrane modulators.

PubMed

Salzer, Ulrich; Kostan, Julius; Djinović-Carugo, Kristina

2017-07-01

The BAR domain is the eponymous domain of the "BAR-domain protein superfamily", a large and diverse set of mostly multi-domain proteins that play eminent roles at the membrane cytoskeleton interface. BAR domain homodimers are the functional units that peripherally associate with lipid membranes and are involved in membrane sculpting activities. Differences in their intrinsic curvatures and lipid-binding properties account for a large variety in membrane modulating properties. Membrane activities of BAR domains are further modified and regulated by intramolecular or inter-subunit domains, by intermolecular protein interactions, and by posttranslational modifications. Rather than providing detailed cell biological information on single members of this superfamily, this review focuses on biochemical, biophysical, and structural aspects and on recent findings that paradigmatically promote our understanding of processes driven and modulated by BAR domains.

Influence of the weighing bar position in vessel on measurement of cement’s particle size distribution by using the buoyancy weighing-bar method

NASA Astrophysics Data System (ADS)

Tambun, R.; Sihombing, R. O.; Simanjuntak, A.; Hanum, F.

2018-02-01

The buoyancy weighing-bar method is a new simple and cost-effective method to determine the particle size distribution both settling and floating particle. In this method, the density change in a suspension due to particle migration is measured by weighing buoyancy against a weighing-bar hung in the suspension, and then the particle size distribution is calculated using the length of the bar and the time-course change in the mass of the bar. The apparatus of this method consists of a weighing-bar and an analytical balance with a hook for under-floor weighing. The weighing bar is used to detect the density change in suspension. In this study we investigate the influences of position of weighing bar in vessel on settling particle size distribution measurements of cement by using the buoyancy weighing-bar method. The vessel used in this experiment is graduated cylinder with the diameter of 65 mm and the position of weighing bar is in center and off center of vessel. The diameter of weighing bar in this experiment is 10 mm, and the kerosene is used as a dispersion liquids. The results obtained show that the positions of weighing bar in vessel have no significant effect on determination the cement’s particle size distribution by using buoyancy weighing-bar method, and the results obtained are comparable to those measured by using settling balance method.

A Modern Picture of Barred Galaxy Dynamics

NASA Astrophysics Data System (ADS)

Petersen, Michael; Weinberg, Martin; Katz, Neal

2018-01-01

Observations of disk galaxies suggest that bars are responsible for altering global galaxy parameters (e.g. structures, gas fraction, star formation rate). The canonical understanding of the mechanisms underpinning bar-driven secular dynamics in disk galaxies has been largely built upon the analysis of linear theory, despite galactic bars being clearly demonstrated to be nonlinear phenomena in n-body simulations. We present simulations of barred Milky Way-like galaxy models designed to elucidate nonlinear barred galaxy dynamics. We have developed two new methodologies for analyzing n-body simulations that give the best of both powerful analytic linear theory and brute force simulation analysis: orbit family identification and multicomponent torque analysis. The software will be offered publicly to the community for their own simulation analysis.The orbit classifier reveals that the details of kinematic components in galactic disks (e.g. the bar, bulge, thin disk, and thick disk components) are powerful discriminators of evolutionary paradigms (i.e. violent instabilities and secular evolution) as well as the basic parameters of the dark matter halo (mass distribution, angular momentum distribution). Multicomponent torque analysis provides a thorough accounting of the transfer of angular momentum between orbits, global patterns, and distinct components in order to better explain the underlying physics which govern the secular evolution of barred disk galaxies.Using these methodologies, we are able to identify the successes and failures of linear theory and traditional n-body simulations en route to a detailed understanding of the control bars exhibit over secular evolution in galaxies. We present explanations for observed physical and velocity structures in observations of barred galaxies alongside predictions for how structures will vary with dynamical properties from galaxy to galaxy as well as over the lifetime of a galaxy, finding that the transfer of angular

10 CFR 39.49 - Uranium sinker bars.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 1 2014-01-01 2014-01-01 false Uranium sinker bars. 39.49 Section 39.49 Energy NUCLEAR REGULATORY COMMISSION LICENSES AND RADIATION SAFETY REQUIREMENTS FOR WELL LOGGING Equipment § 39.49 Uranium sinker bars. The licensee may use a uranium sinker bar in well logging applications only if it is legibly...

10 CFR 39.49 - Uranium sinker bars.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 1 2013-01-01 2013-01-01 false Uranium sinker bars. 39.49 Section 39.49 Energy NUCLEAR REGULATORY COMMISSION LICENSES AND RADIATION SAFETY REQUIREMENTS FOR WELL LOGGING Equipment § 39.49 Uranium sinker bars. The licensee may use a uranium sinker bar in well logging applications only if it is legibly...

10 CFR 39.49 - Uranium sinker bars.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 1 2012-01-01 2012-01-01 false Uranium sinker bars. 39.49 Section 39.49 Energy NUCLEAR REGULATORY COMMISSION LICENSES AND RADIATION SAFETY REQUIREMENTS FOR WELL LOGGING Equipment § 39.49 Uranium sinker bars. The licensee may use a uranium sinker bar in well logging applications only if it is legibly...

10 CFR 39.49 - Uranium sinker bars.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 1 2011-01-01 2011-01-01 false Uranium sinker bars. 39.49 Section 39.49 Energy NUCLEAR REGULATORY COMMISSION LICENSES AND RADIATION SAFETY REQUIREMENTS FOR WELL LOGGING Equipment § 39.49 Uranium sinker bars. The licensee may use a uranium sinker bar in well logging applications only if it is legibly...

10 CFR 39.49 - Uranium sinker bars.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Uranium sinker bars. 39.49 Section 39.49 Energy NUCLEAR REGULATORY COMMISSION LICENSES AND RADIATION SAFETY REQUIREMENTS FOR WELL LOGGING Equipment § 39.49 Uranium sinker bars. The licensee may use a uranium sinker bar in well logging applications only if it is legibly...

The Comparative Observational Study of Timescale of Feedback by Bar Structure in Late-type Galaxies

NASA Astrophysics Data System (ADS)

Woong-bae Woong-bae Zee, Galaxy; Yoon, Suk-jin

2018-01-01

We investigate star formation activities of ~400 barred and ~1400 unbarred faced-on late-type galaxies from the SDSS DR13. We find that gas-poor and barred galaxies are considerably show enhanced high central star formation activities, while there is no difference among gas-rich barred and unbarred galaxies regardless of their HI gas content. This seems counter-intuitive given that gas contents simply represent the total star formation rate of galaxies and suggests that there is a time delation between the central gas migration/consumption through bar structures and the enhancement of star formation activity at the centre. We analysed the distribution of the stellar population of specific galaxies with MaNGA (Mapping Nearby Galaxies at APO) IFU survey among the total samples. The gas-poor and barred galaxies show the flatter gradient in metallicity and age with respect to the stellar mass than other types of galaxies, in that their centre is more metal-rich and younger. There is an age difference, about 5-6 Gyrs, between centrally star-forming gas-poor barred galaxies and gas-rich galaxies and this value is a plausible candidate of the longevity of bar feedback. The results indicate that the gas migration/mixing driven by bar structure plays a significant role in the evolution of galaxies in a specific of timescale.

Pressure effect on the Raman and photoluminescence spectra of Eu3+-doped Na2Ti6O13 nanorods

NASA Astrophysics Data System (ADS)

Zeng, Q. G.; Yang, G. T.; Chen, F.; Luo, J. Y.; Zhang, Z. M.; Leung, C. W.; Ding, Z. J.; Sheng, Y. Q.

2013-12-01

Eu3+-doped Na2Ti6O13 (Na2Ti6O13:Eu) nanorods with diameters of 30 nm and lengths 400 nm were synthesized by hydrothermal and heat treatment methods. Raman spectra at ambient conditions indicated a pure monoclinic phase (space group C2/m) of the nanorods. The relations between structural and optical properties of Na2Ti6O13:Eu nanorods under high pressures were obtained by photoluminescence and Raman spectra. Two structural transition points at 1.39 and 15.48 GPa were observed when the samples were pressurized. The first transition point was attributed to the crystalline structural distortion. The later transition point was the result of pressure-induced amorphization, and the high-density amorphous (HDA) phase formed after 15.48 GPa was structurally related to the monoclinic baddeleyite structured TiO2 (P21/c). However, the site symmetry of the local environment around the Eu3+ ions in Na2Ti6O13 increased with the rising pressure. These above results indicate the occurrence of short-range order for the local asymmetry around the Eu3+ ions and long-range disorder for the crystalline structure of Na2Ti6O13:Eu nanorods by applying pressure. After releasing the pressure from 22.74 GPa, the HDA phase is transformed to low-density amorphous form, which is attributed to be structurally related to the α-PbO2-type TiO2.

THE NATURE AND NURTURE OF BARS AND DISKS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mendez-Abreu, J.; Aguerri, J. A. L.; Zarattini, S.

The effects that interactions produce on galaxy disks and how they modify the subsequent formation of bars need to be distinguished to fully understand the relationship between bars and environment. To this aim we derive the bar fraction in three different environments ranging from the field to Virgo and Coma Clusters, covering an unprecedentedly large range of galaxy luminosities (or, equivalently, stellar masses). We confirm that the fraction of barred galaxies strongly depends on galaxy luminosity. We also show that the difference between the bar fraction distributions as a function of galaxy luminosity (and mass) in the field and Comamore » Cluster is statistically significant, with Virgo being an intermediate case. The fraction of barred galaxies shows a maximum of about 50% at M{sub r} {approx_equal} - 20.5 in clusters, whereas the peak is shifted to M{sub r} {approx_equal} - 19 in the field. We interpret this result as a variation of the effect of environment on bar formation depending on galaxy luminosity. We speculate that brighter disk galaxies are stable enough against interactions to keep their cold structure, thus, the interactions are able to trigger bar formation. For fainter galaxies, the interactions become strong enough to heat up the disks inhibiting bar formation and even destroying the disks. Finally, we point out that the controversy regarding whether the bar fraction depends on environment could be resolved by taking into account the different luminosity ranges probed by the galaxy samples studied so far.« less

Scroll bar growth on the coastal Trinity River, TX, USA

NASA Astrophysics Data System (ADS)

Mason, J.; Hassenruck-Gudipati, H. J.; Mohrig, D. C.

2017-12-01

The processes leading to the formation and growth of scroll bars remain relatively mysterious despite how often they are referenced in fluvial literature. Their definition is descriptive; they are characterized as arcuate topographic highs present on the inner banks of channel bends on meandering rivers, landward of point bars. Often, they are used as proxies for previous positions of point bars. This assumption of a one-to-one correspondence between point bars and scroll bars should be reconsidered as 1) planform curvature for scroll bars is consistently smaller than the curvature for adjacent point bars, and 2) deposition on the scroll bar is typically distinct and disconnected from the adjacent point bar deposition. Results from time-lapse airborne lidar data as well as from trenches through five separate scroll bar - point bar pairings on the Trinity River in east TX, USA, will be discussed in relation to formative scroll bar processes and their connection to point bars. On the lidar difference map, scroll bar growth appears as a strip of increased deposition flanked on both the land- and channel-ward sides by areas with no or limited deposition. Trenches perpendicular to these scrolls typically show a base of dune-scale cross stratification interpreted to be associated with a previous position of the point bar. These dune sets are overlain by sets of climbing-ripple cross-strata that form the core of the modern scroll bar and preserve a record of multiple transport directions (away from, towards, and parallel to the channel). Preliminary Trinity River grain-size analyses show that the constructional scrolls are enriched in all grain sizes less than 250 microns in diameter, while point bars are enriched in all grain sizes above this cut off. Scroll bars are hypothesized to be akin to levees along the inner banks of channels-flow expansion caused by the presence of point bars induces deposition of suspended sediment that defines the positions of the scroll bars.

Nutritional Evaluation of NASA's Rodent Food Bar Diet

NASA Technical Reports Server (NTRS)

Barrett, Joyce E.; Yu, Diane S.; Dalton, Bonnie P.

2000-01-01

Tests are being conducted on NASA's rodent Food Bar in preparation for long-term use as the rat and mouse diet aboard the International Space Station. Nutritional analyses are performed after the bars are manufactured and then repeated periodically to determine nutritional stability. The primary factors analyzed are protein, ash, fat, fiber, moisture, amino acids, fatty acids, and minerals. Nutrient levels are compared to values published in the National Research Council's dietary requirements for rodents, and also to those contained in several commonly used commercial rodent lab diets. The Food Bar is manufactured from a powdered diet to which moisture is added as it is processed through an extruder. The bars are dipped into potassium sorbate, vacuum-sealed, and irradiated. In order to determine nutrient changes during extrusion and irradiation, the powdered diet, the non-irradiated bars, and the irradiated bars are all analyzed. We have observed lower values for some nutrients (iodine, vitamin K, and iron) in the Food Bars compared with NRC requirements. Many nutrients in the Food Bars are contained at a higher level than levels in the NRC requirements. An additional factor we are investigating is the 26% moisture level in the Food Bars, which drops to about 15% within a week, compared to a stable 10% moisture in many standard lab chow diets. In addition to the nutritional analyses, the food bar is being fed to several strains of rats and mice, and feeding study and necropsy results are being observed (Barrett et al, unpublished data). Information from the nutritional analyses and from the rodent studies will enable us to recommend the formulation that will most adequately meet the rodent Food Bar requirements for long-term use aboard the Space Station.

Multi-wavelength observations of barred, flocculent galaxies

NASA Astrophysics Data System (ADS)

Ratay, Douglas Lee

Although it is generally accepted that large galaxies form through the assemblage of smaller objects, an explanation for the morphology of galaxies is not available. Any complete theory of galaxy morphology must include production and dissolution mechanisms for galactic bars, rings, nuclear bars, spiral arms, and companions. This theory does not exist because of the lack of detailed data from many types of galaxies in different environments. We have defined a new sample of galaxies which are simultaneously flocculent, barred, and isolated. We have performed optical, near-infrared, and radio (HI) observations of the galaxies in this sample. We measured properties of our galaxies including bar length, bar axis ratio, HI diameter, HI mass, and dynamical mass. We found that our sample group is heterogeneous, and compares well to a standard samples of galaxies. We found two of our galaxies to possess companions, and two others to show evidence of current interactions. This is consistent with other observations indicating that local isolated galaxies do not possess a large number of small companions. We cannot rule out the possibility of very small companions. We find that as a group our sample is slightly less luminous than normal galaxies and may be more likely to be involved in interactions. We conclude that the bar and spiral arm features in our sample are due to processes internal to the galaxies, likely involving the interaction between the galactic disk and halo. We defined a control sample of barred, grand design galaxies to further determine the acceptability of barred, flocculent galaxies as a physically meaningful subset of galaxies.

Search for CP Violation in Hyperon Decay: $$\\Xi^- / \\bar{\\Xi}^+$$ and $$\\Lambda / \\bar{\\Lambda}$$ (in French)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leros, Nicolas

2001-06-01

The HyperCP(EB71) experiment, performed at the Fermi National Accelerator Laboratory in the United States, provides a primary search for direct OP violation in the decays ofmore » $$\\Xi^-/\\bar{\\Xi}^+$$ and $$\\Lambda/ \\bar{\\Lambda}$$ hyperons....« less

Development of a novel low-radiation-absorbent lok-bar to reduce X-ray scattering and absorption in RapidArc® treatment planning and dose delivery.

PubMed

Monzen, Hajime; Kubo, Kazuki; Tamura, Mikoto; Hayakawa, Masaru; Nishimura, Yasumasa

2017-05-01

We developed a novel low-radiation-absorbent lok-bar (HM-bar) that is used to secure the immobilizers to the couch. The aim of this study was to investigate the X-ray scattering and absorption properties of the HM-bar in computed tomography (CT) simulation and radiotherapy dose delivery using the Varian Exact™ lok-bar (VL-bar) as a benchmark. CT images were obtained with or without lok-bar, and then each image was visually evaluated for artifacts. The attenuation rates for each lok-bar were measured using a farmer-type ionization chamber (PTW30013) and the I'mRT phantom (IBA Dosimetry GmbH). Measurement points were between gantry angles of 110 and 180°. The treatment apparatus was a NovalisTx (Brainlab AG); X-ray energies were set at 6 MV and 10 MV. In the presence of each lok-bar, the radiation dose was measured in accordance with 10 volumetric modulated arc therapy-stereotactic body radiation therapy (VMAT-SBRT) plans for lung cancer. Artifacts were seldom observed in the CT scans of the HM-bar. The attenuation rate of each lok-bar was higher when the X-ray energy was set at 6 MV than at 10 MV. The highest attenuation rate in the VL-bar was observed at a gantry angle of 112°; the rates were 22.4% at 6 MV and 19.3% at 10 MV. Similarly, the highest attenuation rate for the HM-bar was also observed at a gantry angle of 112°; the rates were 12.2% and 10.1% at 6 MV and 10 MV, respectively. When the VL-bar was evaluated, the isocenter dose of the VMAT-SBRT plans was attenuated by 2.6% as a maximum case. In the case of the HM-bar, the maximum attenuation was 1.4%. In the measurements of each VMAT-SBRT plan, the difference of the dose attenuation rate between the VL-bar and HM-bar was approximately 1%. The HM-bar could be used to minimize the occurrence of artifacts and provide good images in CT scans regarding radiotherapy planning and dose calculation. It can be used for patient therapy at hospitals to provide accurate dose delivery because of its low X

Nearshore bars and the break-point hypothesis

USGS Publications Warehouse

Sallenger, A.H.; Howd, P.A.

1989-01-01

The set of hypotheses calling for bar formation at the break point was tested with field data. During two different experiments, waves were measured across the surf zone coincident with the development of a nearshore bar. We use a criterion, based on the wave height to depth ratio, to determine the offshore limit of the inner surf zone. During the first experiment, the bar became better developed and migrated offshore while remaining well within the inner surf zone. During the second experiment, the surf zone was narrower and we cannot rule out the possibility of break point processes contributing to bar development. We conclude that bars are not necessarily coupled with the break point and can become better developed and migrate offshore while being in the inner surf zone landward from initial wave breaking in the outer surf zone. ?? 1989.

Mild hydrothermal crystal growth of new uranium(IV) fluorides, Na{sub 3.13}Mg{sub 1.43}U{sub 6}F{sub 30} and Na{sub 2.50}Mn{sub 1.75}U{sub 6}F{sub 30}: Structures, optical and magnetic properties

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yeon, Jeongho; Smith, Mark D.; Tapp, Joshua

Two new uranium(IV) fluorides, Na{sub 3.13}Mg{sub 1.43}U{sub 6}F{sub 30} (1) and Na{sub 2.50}Mn{sub 1.75}U{sub 6}F{sub 30} (2), were synthesized through an in situ mild hydrothermal route, and were structurally characterized by single crystal X-ray diffraction. The compounds exhibit complex crystal structures composed of corner- or edge-shared UF{sub 9} and MF{sub 6} (M=Mg, Mn) polyhedra, forming hexagonal channels in the three-dimensional framework, in which ordered or disordered divalent metal and sodium atoms reside. The large hexagonal voids contain the nearly regular M(II)F{sub 6} octahedra and sodium ions, whereas the small hexagonal cavities include M(II) and sodium ions on a mixed-occupied site.more » Magnetic susceptibility measurements yielded effective magnetic moments of 8.36 and 11.6 µ{sub B} for 1 and 2, respectively, confirming the presence and oxidation states of U(IV) and Mn(II). The large negative Weiss constants indicate the spin gap between a triplet and a singlet state in the U(IV). Magnetization data as a function of applied fields revealed that 2 exhibits paramagnetic behavior due to the nonmagnetic singlet ground state of U(IV) at low temperature. UV–vis diffuse reflectance and X-ray photoelectron spectroscopy data were also analyzed. - Graphical abstract: Two new quaternary U(IV) fluorides, Na{sub 3.13}Mg{sub 1.43}U{sub 6}F{sub 30} and Na{sub 2.50}Mn{sub 1.75}U{sub 6}F{sub 30}, were crystallized via an in situ reduction step of U(VI) to U(IV) under mild hydrothermal conditions. The compounds show complex crystal structures based on the 3-D building block of U{sub 6}F{sub 30}. Magnetic property measurements revealed that the U(IV) exhibits a nonmagnetic singlet ground state at low temperature with a spin gap. - Highlights: • Na{sub 3.13}Mg{sub 1.43}U{sub 6}F{sub 30} and Na{sub 2.50}Mn{sub 1.75}U{sub 6}F{sub 30} have been synthesized and characterized. • The U(IV) fluorides exhibit complex three-dimensional crystal structures. �

Experimental Study on Basic Mechanical Properties of BFRP Bars

NASA Astrophysics Data System (ADS)

Fan, Xiaochun; Xu, Ting; Zhou, Zhengrong; Zhou, Xun

2017-10-01

Basalt Fiber Reinforced Polymer (BFRP) bars have the advantages of corrosion resistance, high strength, light weight, good dielectric properties, and they are new type of green reinforced alternative material. In order to determine the mechanical properties of BFRP bars, the tensile strength of basalt fiber bars was necessary to be studied. The diameters of the basalt fiber bars were compared by means of uniaxial tensile test in this article. Then the stress-strain curve can be drawn out. The results show that the stress - strain curve of BFRP bars present straight line relation, and there is no sign before failure; there is no yield platform on the stress-strain curve of BFRP bars, which are typical brittle material;the tensile strength of BFRP bars is about 3 times higher than that of ordinary steel bars. and the elastic modulus is about 1/5 of that of ordinary steel; the ultimate tensile strength of BFRP bars varies little with the increase of diameter, but there exist some differences in modulus values.

On the role of impermeable groins on barred beach morphodynamics: Example of Matalascañas beach, Spain

NASA Astrophysics Data System (ADS)

Sedrati, Mouncef; Morales González, Juan Antonio

2017-04-01

Several studies on barred beaches in settings with mesotidal to macrotidal regimes have focused on cross-shore and alongshore bar mobility. Whereas the general link between hydrodynamics, sediment transport and the response of the intertidal bars and shoreline evolution has been recognized in the literature, the role of coastal defense structures (Breakwaters, groins, seawalls) on bar-trough systems morphodynamics have received more much less attention and the field-based experimental studies of these environments are rare. The main aim of this paper is to highlight the contrasting behavior of a natural and protected barred beach under several hydrodynamics conditions. This paper presents detailed hydrodynamic and morphological data from a field experiment spanning 10 days undertaken in Matalascañas beach, a mesotidal protected vs natural barred beach in the Southern Spanish coast. This mesotidal beach experienced intense erosion in the recent past and therefore it has been partially protected by groins (protection of sea-front touristic residences). During the fieldwork, an intertidal bars in the protected and non-protected areas highlighted contrasting morphological behaviour. The non-protected barred beach shows a less pronounced bar-trough system than the protected zone. Under low energy conditions (significant wave height < 0,6m), onshore bar migration rate in the protected area was more important than the non-protected area. This migration was associated with an onshore sediment transport, resulting from the erosion of the bar's seaward slope. In the same moment, a clear longshore bar migration was observed in the non-protected zone with the absence of this process in the protected zone. During few energetic tides (Significant wave height > 1m), the protected and non-protected zones show a flattening bars processes. The findings of the present study suggest that cross-shore vs longshore bar mobility may even be mitigated by the presence of the groins, which

Testing of a Spray-bar Thermodynamic Vent System in Liquid Nitrogen

NASA Technical Reports Server (NTRS)

Flachbart, R. H.; Hastings, L. J.; Hedayat, A.; Nelson, S. L.; Tucker, S. P.

2005-01-01

To support development of a microgravity pressure control capability for liquid oxygen, thermodynamic vent system (TVS) testing was conducted at Marshall Space Flight Center (MSFC) using liquid nitrogen (LN2) as a LOX simulant. The spray bar TVS hardware used was originally designed by the Boeing Company for testing in liquid hydrogen (LH2). With this concept, a small portion of the tank fluid is passed through a Joule-Thomson (J-T) device, and then through a longitudinal spray bar mixed-heat exchanger in order to cool the bulk fluid. To accommodate the larger mass flow rates associated with LN2, the TVS hardware was modified by replacing the recirculation pump with an LN2 compatible pump and replacing the J-T valve. The primary advantage of the spray-bar configuration is that tank pressure control can be achieved independent of liquid and vapor location, enhancing the applicability of ground test data to microgravity conditions. Performance testing revealed that the spray-bar TVS was effective in controlling tank pressure within a 6.89 kPa band for fill levels of 90%, 50%, and 25%. Tests were also conducted with gaseous helium (GHe) in the ullage. The TVS operated nominally with GHe in the ullage, with performance similar to the tests with gaseous nitrogen (GN2). Testing demonstrated that the spray-bar TVS design was flexible enough for use in two different propellants with minimal hardware modifications.

Effect of bar cross-section and female housing material on retention of mandibular implant bar overdentures: A comparative in vitro study.

PubMed

Abdel-Khalek, Elsayed A; Ibrahim, Abdullah M

2017-01-01

The aim of this study is to evaluate the effect of different cross-sections of bar connecting two implants on the retention of mandibular overdentures with Hader clip or lined with heat-cured resilient liner as a housing material. The retentive values after simulated 1.5 years of service were also recorded. Edentulous mandibular acrylic model was constructed with two dummy implants located in the canine region and connected with cast bar assembly. According to bar cross-section and anchoring method, four groups ( n = 10) of identical overdentures were used as Hader bar/clip group (HCG), Hader bar/silicone liner female housing group (HSG), oval bar/silicone liner female housing group (OSG), and round bar/silicone liner female housing group (RSG). Each overdenture sample was subjected to simulated wear up to 2740 manual insertions/separations. The mean retentive forces were measured at the baseline and after every 500 insertions. The data were statistically analyzed using one-way analysis of variance. The present study demonstrated that all bar cross-sections showed a significant difference at the baseline ( P < 0.05), but HSG showed greater initial retention compared to HCG, OSG, and RSG. OSG showed a significant higher retention after 2740 insertions (simulated five insertions/day). Within the limitation of this in vitro study and for a similar period of service, heat-cured silicone female housing for Hader bar could maintain greater retention for two-implant-retained overdentures than provided by conventional plastic clip after 1.5 year. The oval bar recorded reasonable initial retention values and maintained these values for 1.5 years of service.

Iron isotope effect in the iron arsenide superconductor (Ca0.4Na0.6)Fe2As2

NASA Astrophysics Data System (ADS)

Tsuge, Y.; Nishio, T.; Iyo, A.; Tanaka, Y.; Eisaki, H.

2014-05-01

We report a new sample synthesis technique for polycrystalline (Ca1-xNax)Fe2As2 (06) and measurements of an iron isotope effect in optimally doped (Ca0.4Na0.6)Fe2As2 with three types of iron isotopes (54Fe, natural Fe, and 57Fe). We synthesized isotope samples carefully not to give rise to a difference in the Na content x between different isotope samples, which becomes potentially a factor for an extrinsic difference in the superconducting transition temperature Tc between those samples. No significant difference in lattice parameters between those samples is shown by measurements of powder x-ray diffraction (XRD), implying that the Na content in samples is well-controlled. Our estimate of the iron isotope coefficient αFe defined by -d InTc/d lnMFe, where MFe is the iron isotope mass, is -0.19. These indicate that in (Ca0.4Na0.6)Fe2As2, the iron isotope coefficient becomes definitely negative. We discuss the implications of this fact, considering previous measurements of an iron isotope effect in different iron-based superconductors.

32 CFR 776.66 - Bar admission and disciplinary matters.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 5 2010-07-01 2010-07-01 false Bar admission and disciplinary matters. 776.66... ADVOCATE GENERAL Rules of Professional Conduct § 776.66 Bar admission and disciplinary matters. (a) Bar admission and disciplinary matters. A covered attorney, in connection with any application for bar admission...

Uncertainties in the deprojection of the observed bar properties

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zou, Yanfei; Shen, Juntai; Li, Zhao-Yu, E-mail: jshen@shao.ac.cn

2014-08-10

In observations, it is important to deproject the two fundamental quantities characterizing a bar, i.e., its length (a) and ellipticity (e), to face-on values before any careful analyses. However, systematic estimation on the uncertainties of the commonly used deprojection methods is still lacking. Simulated galaxies are well suited in this study. We project two simulated barred galaxies onto a two-dimensional (2D) plane with different bar orientations and disk inclination angles (i). Bar properties are measured and deprojected with the popular deprojection methods in the literature. Generally speaking, deprojection uncertainties increase with increasing i. All of the deprojection methods behave badlymore » when i is larger than 60°, due to the vertical thickness of the bar. Thus, future statistical studies of barred galaxies should exclude galaxies more inclined than 60°. At moderate inclination angles (i ≤ 60°), 2D deprojection methods (analytical and image stretching), and Fourier-based methods (Fourier decomposition and bar-interbar contrast) perform reasonably well with uncertainties ∼10% in both the bar length and ellipticity, whereas the uncertainties of the one-dimensional (1D) analytical deprojection can be as high as 100% in certain extreme cases. We find that different bar measurement methods show systematic differences in the deprojection uncertainties. We further discuss the deprojection uncertainty factors with the emphasis on the most important one, i.e., the three-dimensional structure of the bar itself. We construct two triaxial toy bar models that can qualitatively reproduce the results of the 1D and 2D analytical deprojections; they confirm that the vertical thickness of the bar is the main source of uncertainties.« less

Bars in Field and Cluster Galaxies at Intermediate Redshifts

NASA Astrophysics Data System (ADS)

Barazza, F. D.; Jablonka, P.; Ediscs Collaboration

2009-12-01

We present the first study of large-scale bars in clusters at intermediate redshifts (z=0.4-0.8). We compare the properties of the bars and their host galaxies in the clusters with those of a field sample in the same redshift range. We use a sample of 945 moderately inclined disk galaxies drawn from the EDisCS project. The morphological classification of the galaxies and the detection of bars are based on deep HST/ACS F814W images. The total optical bar fraction in the redshift range z=0.4-0.8, averaged over the entire sample, is 25%. This is lower than found locally, but in good agreement with studies of bars in field environments at intermediate redshifts. For the cluster and field subsamples, we measure bar fractions of 24% and 29%, respectively. In agreement with local studies, we find that disk-dominated galaxies have a higher bar fraction than bulge-dominated galaxies. We also find, based on a small subsample, that bars in clusters are on average longer than in the field and preferentially found close to the cluster center, where the bar fraction is somewhat higher than at larger distances.

Laboratory and Workplace Assessments of Rivet Bucking Bar Vibration Emissions

PubMed Central

McDowell, Thomas W.; Warren, Christopher; Xu, Xueyan S.; Welcome, Daniel E.; Dong, Ren G.

2016-01-01

Sheet metal workers operating rivet bucking bars are at risk of developing hand and wrist musculoskeletal disorders associated with exposures to hand-transmitted vibrations and forceful exertions required to operate these hand tools. New bucking bar technologies have been introduced in efforts to reduce workplace vibration exposures to these workers. However, the efficacy of these new bucking bar designs has not been well documented. While there are standardized laboratory-based methodologies for assessing the vibration emissions of many types of powered hand tools, no such standard exists for rivet bucking bars. Therefore, this study included the development of a laboratory-based method for assessing bucking bar vibrations which utilizes a simulated riveting task. With this method, this study evaluated three traditional steel bucking bars, three similarly shaped tungsten alloy bars, and three bars featuring spring-dampeners. For comparison the bucking bar vibrations were also assessed during three typical riveting tasks at a large aircraft maintenance facility. The bucking bars were rank-ordered in terms of unweighted and frequency-weighted acceleration measured at the hand-tool interface. The results suggest that the developed laboratory method is a reasonable technique for ranking bucking bar vibration emissions; the lab-based riveting simulations produced similar rankings to the workplace rankings. However, the laboratory-based acceleration averages were considerably lower than the workplace measurements. These observations suggest that the laboratory test results are acceptable for comparing and screening bucking bars, but the laboratory measurements should not be directly used for assessing the risk of workplace bucking bar vibration exposures. The newer bucking bar technologies exhibited significantly reduced vibrations compared to the traditional steel bars. The results of this study, together with other information such as rivet quality, productivity, tool

Improved experimental and diagnostic techniques for dynamic tensile stress–strain measurement with a Kolsky tension bar

NASA Astrophysics Data System (ADS)

Qiu, Ying; Loeffler, Colin M.; Nie, Xu; Song, Bo

2018-07-01

Kolsky tension bar experiments were improved for dynamic tensile stress–strain measurements with higher fidelity and minimal uncertainties. The difficulties associated with specimen gripping, relatively short gage section, and geometric discontinuity at the bar ends all compromise the accuracy of the traditional strain measurement method in a Kolsky tension bar experiment. In this study, an improved three-channel splitting-beam laser extensometer technique was developed to directly and independently track the displacement of the incident and transmission bar interfaces. By adopting a dual-channel configuration on the incident bar side, the resolution and measurement range of this laser extensometer were coordinated between the two channels to provide highly precise measurement at both small and large strains under high strain-rate loading condition. On the transmission bar side an amplified channel, similar to that used on the incident bar side, was adopted to measure the transmission bar displacement with high resolution. With this novel design, a maximum resolution of approximately 500 nm can be obtained for the bar displacement measurement, which corresponds to a strain of 0.0079% for a specimen with 6.35 mm gage length. To further improve the accuracy, a pair of lock nuts were used to tighten the tensile specimen to the bars in an effort not only to prevent the specimen from potential pre-torsional deformation and damage during installation, but also to provide better thread engagement between the specimen and the bar ends. As a demonstration of this technique, dynamic tensile stress–strain response of a 304L stainless steel was characterized with high resolution in both elastic and plastic deformations.

BAR Proteins PSTPIP1/2 Regulate Podosome Dynamics and the Resorption Activity of Osteoclasts

PubMed Central

Sztacho, Martin; Segeletz, Sandra; Sanchez-Fernandez, Maria Arantzazu; Czupalla, Cornelia; Niehage, Christian; Hoflack, Bernard

2016-01-01

Bone resorption in vertebrates relies on the ability of osteoclasts to assemble F-actin-rich podosomes that condense into podosomal belts, forming sealing zones. Sealing zones segregate bone-facing ruffled membranes from other membrane domains, and disassemble when osteoclasts migrate to new areas. How podosome/sealing zone dynamics is regulated remains unknown. We illustrate the essential role of the membrane scaffolding F-BAR-Proline-Serine-Threonine Phosphatase Interacting Proteins (PSTPIP) 1 and 2 in this process. Whereas PSTPIP2 regulates podosome assembly, PSTPIP1 regulates their disassembly. PSTPIP1 recruits, through its F-BAR domain, the protein tyrosine phosphatase non-receptor type 6 (PTPN6) that de-phosphophorylates the phosphatidylinositol 5-phosphatases SHIP1/2 bound to the SH3 domain of PSTPIP1. Depletion of any component of this complex prevents sealing zone disassembly and increases osteoclast activity. Thus, our results illustrate the importance of BAR domain proteins in podosome structure and dynamics, and identify a new PSTPIP1/PTPN6/SHIP1/2-dependent negative feedback mechanism that counterbalances Src and PI(3,4,5)P3 signalling to control osteoclast cell polarity and activity during bone resorption. PMID:27760174

Mechanical splicing of superelastic Cu–Al–Mn alloy bars with headed ends

NASA Astrophysics Data System (ADS)

Kise, S.; Mohebbi, A.; Saiidi, M. S.; Omori, T.; Kainuma, R.; Shrestha, K. C.; Araki, Y.

2018-06-01

This paper examines the feasibility of mechanical splicing using a steel coupler to connect headed ends of superelastic Cu–Al–Mn alloy (Camalloy) bars and steel reinforcing bars to be used in concrete structures. Although threading of Camalloy is as easy as that of steel, mechanical splicing using threaded ends requires machining of Camalloy bars into dog-bone shape to avoid brittle fracture at the threaded ends. The machining process requires significant time and cost and wastes substantial amount of the material. This paper attempts to resolve this issue by applying mechanical splicing using steel couplers to connect headed ends of Camalloy and steel reinforcing bars. To study its feasibility, we prepare 3 specimens wherein both ends of each Camalloy bar (13 mm diameter and 300 mm length) are connected to steel reinforcing bars. The specimens are tested under monotonic, single-cycle, and full-cycle tension loading conditions. From these tests, we observed (1) excellent superelasticity with recoverable strain of around 6% and (2) large ductility with fracture strain of over 19%. It should be emphasized here that, in all the specimens, ductile fracture occurred at the locations apart from the headed ends. This is in sharp contrast with brittle fracture of headed superelastic Ni–Ti SMA bars, most of which took place around the headed ends. From the results of the microstructural analysis, we identified the following reasons for avoiding brittle fracture at the headed ends: (1) Precipitation hardening increases the strength around the boundary between the straight and headed (tapered) portions, where stress concentration takes place. (2) The strength of the straight portion does not increase significantly up to the ductile fracture if its grain orientation is close to 〈0 0 1〉.

Impact of the Lok-bar for High-precision Radiotherapy with Tomotherapy.

PubMed

Hirata, Makoto; Monzen, Hajime; Tamura, Mikoto; Kubo, Kazuki; Matsumoto, Kenji; Hanaoka, Kohei; Okumura, Masahiko; Nishimura, Yasumasa

2018-05-01

Patient immobilization systems are used to establish a reproducible patient position relative to the couch. In this study, the impact of conventional lok-bars for CT-simulation (CIVCO-bar) and treatment (iBEAM-bar) were compared with a novel lok-bar (mHM-bar) in tomotherapy. Verification was obtained as follows: i. artifacts in CT images; ii. dose attenuation rate of lok-bar, compared to without lok-bar; and iii. dose differences between the calculated and measured absorbed doses. With the CIVCO-bar, there were obvious metal artifacts, while there were nearly no artifacts with the mHM-bar. The mean dose attenuation rates with the mHM-bar and iBEAM-bar were 1.31% and 2.28%, and the mean dose difference was 1.55% and 1.66% for mHM-bar and iBEAM-bar. Using the mHM-bar reduced artifacts on the CT image and improved dose attenuation are obtained. The lok-bar needs to be inserted as a structure set in treatment planning with tomotherapy. Copyright© 2018, International Institute of Anticancer Research (Dr. George J. Delinasios), All rights reserved.

Effects of flexi-bar and non-flexi-bar exercises on trunk muscles activity in different postures in healthy adults.

PubMed

Chung, Jun Sub; Park, Seol; Kim, JiYoung; Park, Ji Won

2015-07-01

[Purpose] The purpose of this study was to assess the effects of flexi-bar exercises and non-flexi-bar exercises on trunk muscle activity in different postures in healthy adults. [Subjects] Twenty healthy right-hand dominant adults (10 males and 10 females) were selected for this study. None of the participants had experienced any orthopedic problems in the spine or in the upper and lower extremities in the previous six months. [Methods] The subjects were instructed to adopt three exercise postures: posture 1, quadruped; posture 2, side-bridge; and posture 3, standing. Surface electromyography of selected trunk muscles was normalized to maximum voluntary isometric contraction. [Results] The external oblique, internal oblique, and erector spinae muscle activity showed significant differences between flexi-bar exercises and non-flexi-bar exercises. [Conclusion] The results of this study suggest that flexi-bar exercises are useful in the activation of trunk muscles.

Cyclic stability of superelasticity in the aged [ {bar{1}}23 ]-oriented Ni49Fe18Ga27Co6 single crystals

NASA Astrophysics Data System (ADS)

Panchenko, E. Yu.; Chumlyakov, Yu. I.; Timofeeva, E. E.; Vetoshkina, N. G.; Maier, H.

2013-02-01

The results of investigation of the effect of precipitates of different sizes, from 5 to 300 nm, on the character of stress-induced martensitic transformations, the value of stress hysteresis and cyclic stability of superelasticity in Ni49Fe18Ga27Со6 (at.%) ferromagnetic single crystals oriented along the [ {bar{1}}23 ] axis are presented. It is shown that a martensitic transformation in single crystals of Ni49Fe18Ga27Со6 containing dispersed particles of the γ- and γ'-phases measuring up to 30 nm (ageing at 673 K for 1 and 4 hours) is characterized by storing considerable elastic energy. It is revealed that these single crystals exhibit higher cyclic stability of superelasticity and a narrower stress hysteresis compared to those in the initial state and aged at 823 K for 0.5 hour, the latter containing much larger (150-300 nm) particles.

Na2Ti6O13@TiO2 core-shell nanorods with controllable mesoporous shells and their enhanced photocatalytic performance

NASA Astrophysics Data System (ADS)

Zhou, Xuefan; Zhong, Donglin; Luo, Hang; Pan, Jun; Zhang, Dou

2018-01-01

In this study, dispersive and free-standing Na2Ti6O13 nanorods with diameter of about 500 nm and length of about 10 μm were synthesized by the molten salt method. The Na2Ti6O13@TiO2 (denoted as TTO) core-shell nanorods were fabricated by a versatile kinetics controlled coating method. The TiO2 shells were uniform and mesoporous with exposed {101} facets. The thickness of TiO2 shells can be well controlled by the content of Ti(OC4H9)4, ranging from 0 nm, 15 nm, 60 nm to 70 nm corresponding to Na2Ti6O13, 0.25-TTO, 0.50-TTO and 0.75-TTO nanorods respectively. The crystalline phases, microstructure, porosity, photoabsorption and photocatalytic performance of all the samples were investigated systematically. The nanoscale heterojunction structure between Na2Ti6O13 and TiO2, reductive TiO2 {101} facets and high aspect ratio Na2Ti6O13 nanorods resulted in the enhanced photocatalytic performance of TTO nanorods. The optimized thickness of TiO2 shells were about 60 nm for 0.50-TTO nanorods, which possessed superior BET surface area, optical absorption and photocatalytic performance.

External push and internal pull forces recruit curvature sensing N-BAR domain proteins to the plasma membrane

PubMed Central

Galic, Milos; Jeong, Sangmoo; Tsai, Feng-Chiao; Joubert, Lydia-Marie; Wu, Yi I.; Hahn, Klaus M.; Cui, Yi; Meyer, Tobias

2012-01-01

Many of the more than 20 mammalian proteins with N-BAR domains1-2 control cell architecture3 and endocytosis4-5 by associating with curved sections of the plasma membrane (PM)6. It is not well understood whether N-BAR proteins are recruited directly by processes that mechanically curve the PM or indirectly by PM-associated adaptor proteins that recruit proteins with N-BAR domains that then induce membrane curvature. Here, we show that externally-induced inward deformation of the PM by cone-shaped nanostructures (Nanocones) and internally-induced inward deformation by contracting actin cables both trigger recruitment of isolated N-BAR domains to the curved PM. Markedly, live-cell imaging in adherent cells showed selective recruitment of full length N-BAR proteins and isolated N-BAR domains to PM sub-regions above Nanocone stripes. Electron microscopy confirmed that N-BAR domains are recruited to local membrane sites curved by Nanocones. We further showed that N-BAR domains are periodically recruited to curved PM sites during local lamellipodia retraction in the front of migrating cells. Recruitment required Myosin II-generated force applied to PM connected actin cables. Together, our study shows that N-BAR domains can be directly recruited to the PM by external push or internal pull forces that locally curve the PM. PMID:22750946

Orientational disorder in sodium cadmium trifluoride trihydrate, NaCdF{sub 3}.3H{sub 2}O

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, Robert W.; Mar, Arthur; Liu Jianjun

2006-03-09

Attempts to synthesize the hypothetical anhydrous fluoroperovskite NaCdF{sub 3}, which has been predicted to be stable, resulted instead in a hydrated fluoride of nominal composition NaCdF{sub 3}.3H{sub 2}O. It decomposes to sodium fluoride, cadmium fluoride, and water at 60deg. C. Its structure has been determined by single-crystal X-ray diffraction. Na{sub 0.92(2)}Cd{sub 1.08}F{sub 3.08}.2.92H{sub 2}O crystallizes in the cubic space group Fm3-bar m with a=8.2369(4)A and Z=4. The structure is based on the NaSbF{sub 6}-type (an ordered variant of the ReO{sub 3}-type) and features tilted sodium- and cadmium-centred octahedra that are linked by shared vertices to form a three-dimensional network. Substitutionalmore » disorder occurs on the nonmetal site, which is occupied by both F and O atoms, and on one of the metal sites, which is occupied by 92% Na and 8% Cd. A four-fold orientational disorder of the tilted octahedra is manifested as partial occupancy (25%) of the nonmetal site. A scheme to synthesize the anhydrous fluoride is presented.« less

Measurement of |V{sub cb}| using {bar B}{sup 0} {yields} D*{sup +}{ell}{sup -}{bar {nu}}{sub {ell}} Decays

DOE Office of Scientific and Technical Information (OSTI.GOV)

Della Ricca, Giuseppe

A preliminary measurement of |V{sub cb}| and the branching fraction {Beta}({bar B}{sup 0} {yields} D*{sup +}{ell}{sup -}{bar {nu}}{sub {ell}}) has been performed based on a sample of about 55,700 {bar B}{sup 0} {yields} D*{sup +}{ell}{sup -}{bar {nu}}{sub {ell}} decays recorded with the BABAR detector. The decays are identified in the D*{sup +} {yields} D{sup 0}{pi}{sup +} final state, with the D{sup 0} reconstructed in three different decay modes. The differential decay rate is measured as a function of the relativistic boost of the D*{sup +} in the {bar B}{sup 0} rest frame. The value of the differential decay rate atmore » ''zero recoil'', namely the point at which the D*{sup +} is at rest in the {bar B}{sup 0} frame, is predicted in Heavy Quark Effective Theory as a kinematic factor times F(1)|V{sub cb}|, where F is the unique form factor governing the decay. We extrapolate the measured differential decay rate to the zero recoil point and obtain F(1)|V{sub cb}| = (34.03 {+-} 0.24 {+-} 1.31) x 10{sup -3}. Using a theoretical calculation for F(1) we extract |V{sub cb}| = (37.27 {+-} 0.26(stat.) {+-} 1.43(syst.){sub -1.2}{sup +1.5}(theo.)) x 10{sup -3}. From the integrated decay rate we obtain {Beta}({bar B}{sup 0} {yields} D*{sup +}{ell}{sup -}{bar {nu}}{sub {ell}}) = (4.68 {+-} 0.03 {+-} 0.29)%.« less

21 CFR 610.67 - Bar code label requirements.

Code of Federal Regulations, 2012 CFR

2012-04-01

... or to blood and blood components intended for transfusion. For blood and blood components intended...) BIOLOGICS GENERAL BIOLOGICAL PRODUCTS STANDARDS Labeling Standards § 610.67 Bar code label requirements. Biological products must comply with the bar code requirements at § 201.25 of this chapter. However, the bar...

21 CFR 610.67 - Bar code label requirements.

Code of Federal Regulations, 2013 CFR

2013-04-01

... or to blood and blood components intended for transfusion. For blood and blood components intended...) BIOLOGICS GENERAL BIOLOGICAL PRODUCTS STANDARDS Labeling Standards § 610.67 Bar code label requirements. Biological products must comply with the bar code requirements at § 201.25 of this chapter. However, the bar...

21 CFR 610.67 - Bar code label requirements.

Code of Federal Regulations, 2014 CFR

2014-04-01

... or to blood and blood components intended for transfusion. For blood and blood components intended...) BIOLOGICS GENERAL BIOLOGICAL PRODUCTS STANDARDS Labeling Standards § 610.67 Bar code label requirements. Biological products must comply with the bar code requirements at § 201.25 of this chapter. However, the bar...

Laboratory and workplace assessments of rivet bucking bar vibration emissions.

PubMed

McDowell, Thomas W; Warren, Christopher; Xu, Xueyan S; Welcome, Daniel E; Dong, Ren G

2015-04-01

Sheet metal workers operating rivet bucking bars are at risk of developing hand and wrist musculoskeletal disorders associated with exposures to hand-transmitted vibrations and forceful exertions required to operate these hand tools. New bucking bar technologies have been introduced in efforts to reduce workplace vibration exposures to these workers. However, the efficacy of these new bucking bar designs has not been well documented. While there are standardized laboratory-based methodologies for assessing the vibration emissions of many types of powered hand tools, no such standard exists for rivet bucking bars. Therefore, this study included the development of a laboratory-based method for assessing bucking bar vibrations which utilizes a simulated riveting task. With this method, this study evaluated three traditional steel bucking bars, three similarly shaped tungsten alloy bars, and three bars featuring spring-dampeners. For comparison the bucking bar vibrations were also assessed during three typical riveting tasks at a large aircraft maintenance facility. The bucking bars were rank-ordered in terms of unweighted and frequency-weighted acceleration measured at the hand-tool interface. The results suggest that the developed laboratory method is a reasonable technique for ranking bucking bar vibration emissions; the lab-based riveting simulations produced similar rankings to the workplace rankings. However, the laboratory-based acceleration averages were considerably lower than the workplace measurements. These observations suggest that the laboratory test results are acceptable for comparing and screening bucking bars, but the laboratory measurements should not be directly used for assessing the risk of workplace bucking bar vibration exposures. The newer bucking bar technologies exhibited significantly reduced vibrations compared to the traditional steel bars. The results of this study, together with other information such as rivet quality, productivity, tool

[6]-gingerol and [6]-shogaol, active ingredients of the traditional Japanese medicine hangeshashinto, relief oral ulcerative mucositis-induced pain via action on Na+ channels.

PubMed

Hitomi, Suzuro; Ono, Kentaro; Terawaki, Kiyoshi; Matsumoto, Chinami; Mizuno, Keita; Yamaguchi, Kiichiro; Imai, Ryota; Omiya, Yuji; Hattori, Tomohisa; Kase, Yoshio; Inenaga, Kiyotoshi

2017-03-01

The traditional Japanese herbal medicine hangeshashinto (HST) has beneficial effects for the treatment of oral ulcerative mucositis (OUM) in cancer patients. However, the ingredient-based mechanism that underlies its pain-relieving activity remains unknown. In the present study, to clarify the analgesic mechanism of HST on OUM-induced pain, we investigated putative HST ingredients showing antagonistic effects on Na + channels in vitro and in vivo. A screen of 21 major ingredients using automated patch-clamp recordings in channel-expressing cells showed that [6]-gingerol and [6]-shogaol, two components of a Processed Ginger extract, considerably inhibited voltage-activated Na + currents. These two ingredients inhibited the stimulant-induced release of substance P and action potential generation in cultured rat sensory neurons. A submucosal injection of a mixture of [6]-gingerol and [6]-shogaol increased the mechanical withdrawal threshold in healthy rats. In a rat OUM model, OUM-induced mechanical pain was alleviated 30min after the swab application of HST despite the absence of anti-bacterial and anti-inflammatory actions in the OUM area. A swab application of a mixture of [6]-gingerol and [6]-shogaol induced sufficient analgesia of OUM-induced mechanical or spontaneous pain when co-applied with a Ginseng extract containing abundant saponin. The Ginseng extract demonstrated an acceleration of substance permeability into the oral ulcer tissue without an analgesic effect. These findings suggest that Na + channel blockage by gingerol/shogaol plays an essential role in HST-associated analgesia of OUM-induced pain. This pharmacological mechanism provides scientific evidence supporting the use of this herbal medicine in patients suffering from OUM-induced pain. Copyright © 2017 Elsevier Ltd. All rights reserved.

Chemical enrichment in isolated barred spiral galaxies.

NASA Astrophysics Data System (ADS)

Martel, Hugo; Carles, Christian; Robichaud, Fidéle; Ellison, Sara L.; Williamson, David J.

2018-04-01

To investigate the role of bars in the chemical evolution of isolated disc galaxies, we performed a series of 39 gas dynamical simulations of isolated barred and unbarred galaxies with various masses, initial gas fractions, and AGN feedback models. The presence of a bar drives a substantial amount of gas toward the central region of the galaxy. In the most massive galaxies, this results in a violent starburst, followed by a drop in star formation resulting from gas exhaustion. The time delay between Type Ia and Type II supernovae explosions means that barred galaxies experience a rapid increase in [O/H] in the central region, and a much more gradual increase in [Fe/H]. In unbarred galaxies, star formation proceeds at a slow and steady rate, and oxygen and iron are produced at steady rates which are similar except for a time offset. Comparing the abundance ratios in barred and unbarred galaxies with the same central stellar mass M*, we find in barred galaxies an enhancement of 0.07 dex in [O/H], 0.05 dex in [Fe/H], and 0.05 dex in [O/Fe]. The [O/H] enhancement is in excellent agreement with observations from the SDSS. The initial gas fraction has very little effect on the abundance ratios in barred and unbarred galaxies, unless the galaxies experience a starburst. We considered AGN-host galaxies located near the bottom of the AGN regime, M* ≳ 3 × 1010M⊙, where AGN feedback dominates over supernovae feedback. We found that the impact of AGN feedback on the central abundances is marginal.

Bridge-indentation precracking of glass bars

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lue, J.L.; Scattergood, R.O.

1993-07-01

Bridge indentation precracking was first reported by Sadahiro et al., and has been used by a number of subsequent investigators. The procedure involves placing a half-penny starter crack, formed by Vickers indentation, at the center of the bottom surface of a rectangular bar specimen. The bar is loaded between pusher and anvil platens. The bridge span S produces tensile bending stress on the bottom surface of the bar, which contains the starter crack. With increasing load, the crack grows stably outward and inward, and at a certain load the crack will propagate unstably (pop-in) to a straight, through-section crack ofmore » length c. The method is very convenient for producing sharp, through-section precracks in ceramic bars without the need for saw cutting or fatigue cycling. However, the effects of bridge geometry and friction on the precracking results will be presented here which point to an important influence of the friction between the specimen and anvil platens.« less

Metal/polymer composite Nuss bar for minimally invasive bar removal after Pectus Excavatum treatment: FEM simulations.

PubMed

Ricotti, Leonardo; Ciuti, Gastone; Ghionzoli, Marco; Messineo, Antonio; Menciassi, Arianna

2014-12-01

This study aims at assessing the mechanical behavior of a composite metal/polymer bar to be implanted in the retrosternal position, in order to correct chest wall deformities, such as Pectus Excavatum. A 300-mm-long, 12.7-mm-wide, and 3.5-mm-thick Nuss bar was considered, made of different metals and biodegradable polymers, fixed at its extremities, and with a constant force of 250 N applied on its center. Two different geometries for the metal elements to be embedded in the polymeric matrix were tested: in the former, thin metal sheets and in the latter, cylindrical metal reinforcing rods were considered. Finite element method simulation results are reported, in terms of maximum stress and strain of the bar. Furthermore, the maximum stress values obtained by varying metal sheet thickness or rod diameter (and therefore the volumetric percentage of metal within the matrix) for different material combinations are also shown; optimal configuration for the Pectus Excavatum treatment was finally identified for a composite Nuss bar. Copyright © 2014 John Wiley & Sons, Ltd.

Multi-stir bar sorptive extraction for analysis of odor compounds in aqueous samples.

PubMed

Ochiai, Nobuo; Sasamoto, Kikuo; Ieda, Teruyo; David, Frank; Sandra, Pat

2013-11-08

enrichment for most of the selected compounds compared to conventional SBSE using the PDMS stir bar or the EG Silicone stir bar. Fifteen compounds were determined in the range of 0.15-210 ng mL(-1) (RSD<14%, n=6). Copyright © 2013 Elsevier B.V. All rights reserved.

Bond Strength of Composite CFRP Reinforcing Bars in Timber

PubMed Central

Corradi, Marco; Righetti, Luca; Borri, Antonio

2015-01-01

The use of near-surface mounted (NSM) fibre-reinforced polymer (FRP) bars is an interesting method for increasing the shear and flexural strength of existing timber members. This article examines the behaviour of carbon FRP (CFRP) bars in timber under direct pull-out conditions. The objective of this experimental program is to investigate the bond strength between composite bars and timber: bars were epoxied into small notches made into chestnut and fir wood members using a commercially-available epoxy system. Bonded lengths varied from 150 to 300 mm. Failure modes, stress and strain distributions and the bond strength of CFRP bars have been evaluated and discussed. The pull-out capacity in NSM CFRP bars at the onset of debonding increased with bonded length up to a length of 250 mm. While CFRP bar’s pull-out was achieved only for specimens with bonded lengths of 150 and 200 mm, bar tensile failure was mainly recorded for bonded lengths of 250 and 300 mm. PMID:28793423

Compliance with smoke-free policies in Korean bars and restaurants: A descriptive analysis in California

PubMed Central

Irvin, Veronica L.; Hofstetter, C. Richard; Nichols, Jeanne F.; Chambers, Christina D.; Usita, Paula M.; Norman, Gregory J.; Kang, Sunny; Hovell, Melbourne F.

2015-01-01

Objective Compliance with California's smoke-free restaurant and bar policies may be more a function of social contingencies and less a function of legal contingencies. The aims of this study are: 1) to report indications of compliance with smoke-free legislation in Korean bars and restaurants in California; 2) to examine the demographic, smoking status, and acculturation factors of who smoked indoors; and 3) to report social cues in opposition to smoking among a sample of Koreans in California. Method Data were collected by telephone surveys administered by bilingual interviewers between 2007– 2009, and included California adults of Korean descent who visited a Korean bar or restaurant in a typical month (N=2,173, 55% female). Results 1% of restaurant-going participants smoked inside while 7% observed someone else smoke inside a Korean restaurant. 23% of bar-going participants smoked inside and 65% observed someone else smoke inside a Korean bar. Presence of ashtrays was related to indoor smoking in bars and restaurants. Among participants who observed smoking, a higher percentage observed someone ask a smoker to stop (17.6%) or gesture to a smoker (27.0%) inside Korean restaurants (N=169) than inside Korean bars (n=141, 17.0% observed verbal cue and 22.7% observed gesture). Participants who smoked inside were significantly younger and more acculturated than participants who did not. Less acculturated participants were significantly more to likely to be told to stop smoking. Conclusions Ten years after implementation of ordinances, smoking was common in Korean bars in California. PMID:25735336

Compliance with smoke-free policies in korean bars and restaurants in california: a descriptive analysis.

PubMed

Irvin, Veronica L; Hofstetter, C Richard; Nichols, Jeanne F; Chambers, Christina D; Usita, Paula M; Norman, Gregory J; Kang, Sunny; Hovell, Melbourne F

2015-01-01

Compliance with California's smoke-free restaurant and bar policies may be more a function of social contingencies and less a function of legal contingencies. The aims of this study were: 1) to report indications of compliance with smoke-free legislation in Korean bars and restaurants in California; 2) to examine the demographic, smoking status, and acculturation factors of who smoked indoors; and 3) to report social cues in opposition to smoking among a sample of Koreans in California. Data were collected by telephone surveys administered by bilingual interviewers between 2007-2009, and included California adults of Korean descent who visited a Korean bar or restaurant in a typical month (N=2,173, 55% female). 1% of restaurant-going participants smoked inside while 7% observed someone else smoke inside a Korean restaurant. Some 23% of bar-going participants smoked inside and 65% observed someone else smoke inside a Korean bar. Presence of ashtrays was related to indoor smoking in bars and restaurants. Among participants who observed smoking, a higher percentage observed someone ask a smoker to stop (17.6%) or gesture to a smoker (27.0%) inside Korean restaurants (N=169) than inside Korean bars (n=141, 17.0% observed verbal cue and 22.7% observed gesture). Participants who smoked inside were significantly younger and more acculturated than participants who did not. Less acculturated participants were significantly more to likely to be told to stop smoking. Ten years after implementation of ordinances, smoking appears to be common in Korean bars in California.

Snack bar compositions and their acute glycaemic and satiety effects.

PubMed

Yan, Mary R; Parsons, Andrew; Whalley, Gillian A; Kelleher, John; Rush, Elaine C

Maintaining blood glucose within homeostatic limits and eating foods that sup-press hunger and promote satiety have beneficial impacts for health. This study investigated the glycaemic re-sponse and satiety effects of a serving size of a healthier snack bar, branded Nothing Else, that met the required nutrient profiling score criteria for a health claim, in comparison to two top-selling commercial snack bars. In an experimental study, 24 participants aged >=50 years were recruited. On three different days blood glucose concentration was measured twice at baseline and 15, 30, 45, 60, 90 and 120 minutes after consumption of a serving size of each bar. Satiety effects were self-reported hunger, fullness, desire to eat, and amount could eat ratings on visual analogue scales. The incremental area under the blood glucose response curve (iAUC) over two hours for the Nothing Else bar was 30% lower than commercial Bar 2 (p<0.001). At 45 minutes after eating, the Nothing Else bar induced the highest fullness rating and lowest hunger rating among the three snack bars. At two hours, fullness induced by the Nothing Else bar was twice that of Bar 2 (p=0.019), but not different to Bar 1 (p=0.212). The Nothing Else snack bar developed using the nutrient profiling scheme as a guideline, with its high protein and dietary fibre contents, had a lower glycaemic impact and induced a higher subjective satiety than the two commercial snack bars of equal weight.

Predicting vertical jump height from bar velocity.

PubMed

García-Ramos, Amador; Štirn, Igor; Padial, Paulino; Argüelles-Cienfuegos, Javier; De la Fuente, Blanca; Strojnik, Vojko; Feriche, Belén

2015-06-01

The objective of the study was to assess the use of maximum (Vmax) and final propulsive phase (FPV) bar velocity to predict jump height in the weighted jump squat. FPV was defined as the velocity reached just before bar acceleration was lower than gravity (-9.81 m·s(-2)). Vertical jump height was calculated from the take-off velocity (Vtake-off) provided by a force platform. Thirty swimmers belonging to the National Slovenian swimming team performed a jump squat incremental loading test, lifting 25%, 50%, 75% and 100% of body weight in a Smith machine. Jump performance was simultaneously monitored using an AMTI portable force platform and a linear velocity transducer attached to the barbell. Simple linear regression was used to estimate jump height from the Vmax and FPV recorded by the linear velocity transducer. Vmax (y = 16.577x - 16.384) was able to explain 93% of jump height variance with a standard error of the estimate of 1.47 cm. FPV (y = 12.828x - 6.504) was able to explain 91% of jump height variance with a standard error of the estimate of 1.66 cm. Despite that both variables resulted to be good predictors, heteroscedasticity in the differences between FPV and Vtake-off was observed (r(2) = 0.307), while the differences between Vmax and Vtake-off were homogenously distributed (r(2) = 0.071). These results suggest that Vmax is a valid tool for estimating vertical jump height in a loaded jump squat test performed in a Smith machine. Key pointsVertical jump height in the loaded jump squat can be estimated with acceptable precision from the maximum bar velocity recorded by a linear velocity transducer.The relationship between the point at which bar acceleration is less than -9.81 m·s(-2) and the real take-off is affected by the velocity of movement.Mean propulsive velocity recorded by a linear velocity transducer does not appear to be optimal to monitor ballistic exercise performance.

Predicting Vertical Jump Height from Bar Velocity

PubMed Central

García-Ramos, Amador; Štirn, Igor; Padial, Paulino; Argüelles-Cienfuegos, Javier; De la Fuente, Blanca; Strojnik, Vojko; Feriche, Belén

2015-01-01

The objective of the study was to assess the use of maximum (Vmax) and final propulsive phase (FPV) bar velocity to predict jump height in the weighted jump squat. FPV was defined as the velocity reached just before bar acceleration was lower than gravity (-9.81 m·s-2). Vertical jump height was calculated from the take-off velocity (Vtake-off) provided by a force platform. Thirty swimmers belonging to the National Slovenian swimming team performed a jump squat incremental loading test, lifting 25%, 50%, 75% and 100% of body weight in a Smith machine. Jump performance was simultaneously monitored using an AMTI portable force platform and a linear velocity transducer attached to the barbell. Simple linear regression was used to estimate jump height from the Vmax and FPV recorded by the linear velocity transducer. Vmax (y = 16.577x - 16.384) was able to explain 93% of jump height variance with a standard error of the estimate of 1.47 cm. FPV (y = 12.828x - 6.504) was able to explain 91% of jump height variance with a standard error of the estimate of 1.66 cm. Despite that both variables resulted to be good predictors, heteroscedasticity in the differences between FPV and Vtake-off was observed (r2 = 0.307), while the differences between Vmax and Vtake-off were homogenously distributed (r2 = 0.071). These results suggest that Vmax is a valid tool for estimating vertical jump height in a loaded jump squat test performed in a Smith machine. Key points Vertical jump height in the loaded jump squat can be estimated with acceptable precision from the maximum bar velocity recorded by a linear velocity transducer. The relationship between the point at which bar acceleration is less than -9.81 m·s-2 and the real take-off is affected by the velocity of movement. Mean propulsive velocity recorded by a linear velocity transducer does not appear to be optimal to monitor ballistic exercise performance. PMID:25983572

Gas inflow patterns and nuclear rings in barred galaxies

NASA Astrophysics Data System (ADS)

Shen, Juntai; Li, Zhi

2017-06-01

Nuclear rings, dust lanes, and nuclear spirals are common structures in the inner region of barred galaxies, with their shapes and properties linked to the physical parameters of the galaxies. We use high-resolution hydrodynamical simulations to study gas inflow patterns in barred galaxies, with special attention on the nuclear rings. The location and thickness of nuclear ringsare tightly correlated with galactic properties, such as the bar pattern speed and bulge central density, within certain ranges. We identify the backbone of nuclear rings with a major orbital family of bars. The rings form exactly at the radius where the residual angular momentum of inflowing gas balances the centrifugal force. We propose a new simple method to predict the bar pattern speed for barred galaxies possessing a nuclear ring, without actually doing simulations. We apply this method to some real galaxies and find that our predicted bar pattern speed compare reasonably well with other estimates. Our study may have important implications for using nuclear ringsto measure the parameters of real barred galaxies with detailed gas kinematics. We have also extended current hydrodynamical simulations to model gas features in the Milky Way.

33 CFR 13.01-40 - Miniature medals and bars.

Code of Federal Regulations, 2012 CFR

2012-07-01

... GENERAL DECORATIONS, MEDALS, RIBBONS AND SIMILAR DEVICES Gold and Silver Lifesaving Medals, Bars, and Miniatures § 13.01-40 Miniature medals and bars. (a) Miniature Gold and Silver Lifesaving Medals and bars are...

33 CFR 13.01-40 - Miniature medals and bars.

Code of Federal Regulations, 2013 CFR

2013-07-01

... GENERAL DECORATIONS, MEDALS, RIBBONS AND SIMILAR DEVICES Gold and Silver Lifesaving Medals, Bars, and Miniatures § 13.01-40 Miniature medals and bars. (a) Miniature Gold and Silver Lifesaving Medals and bars are...

33 CFR 13.01-40 - Miniature medals and bars.

Code of Federal Regulations, 2011 CFR

2011-07-01

... GENERAL DECORATIONS, MEDALS, RIBBONS AND SIMILAR DEVICES Gold and Silver Lifesaving Medals, Bars, and Miniatures § 13.01-40 Miniature medals and bars. (a) Miniature Gold and Silver Lifesaving Medals and bars are...

33 CFR 13.01-40 - Miniature medals and bars.

Code of Federal Regulations, 2010 CFR

2010-07-01

... GENERAL DECORATIONS, MEDALS, RIBBONS AND SIMILAR DEVICES Gold and Silver Lifesaving Medals, Bars, and Miniatures § 13.01-40 Miniature medals and bars. (a) Miniature Gold and Silver Lifesaving Medals and bars are...

33 CFR 13.01-40 - Miniature medals and bars.

Code of Federal Regulations, 2014 CFR

2014-07-01

... GENERAL DECORATIONS, MEDALS, RIBBONS AND SIMILAR DEVICES Gold and Silver Lifesaving Medals, Bars, and Miniatures § 13.01-40 Miniature medals and bars. (a) Miniature Gold and Silver Lifesaving Medals and bars are...

Visual mining business service using pixel bar charts

NASA Astrophysics Data System (ADS)

Hao, Ming C.; Dayal, Umeshwar; Casati, Fabio

2004-06-01

Basic bar charts have been commonly available, but they only show highly aggregated data. Finding the valuable information hidden in the data is essential to the success of business. We describe a new visualization technique called pixel bar charts, which are derived from regular bar charts. The basic idea of a pixel bar chart is to present all data values directly instead of aggregating them into a few data values. Pixel bar charts provide data distribution and exceptions besides aggregated data. The approach is to represent each data item (e.g. a business transaction) by a single pixel in the bar chart. The attribute of each data item is encoded into the pixel color and can be accessed and drilled down to the detail information as needed. Different color mappings are used to represent multiple attributes. This technique has been prototyped in three business service applications-Business Operation Analysis, Sales Analysis, and Service Level Agreement Analysis at Hewlett Packard Laboratories. Our applications show the wide applicability and usefulness of this new idea.

Chemical enrichment in isolated barred spiral galaxies

NASA Astrophysics Data System (ADS)

Martel, Hugo; Carles, Christian; Robichaud, Fidèle; Ellison, Sara L.; Williamson, David J.

2018-07-01

To investigate the role of bars in the chemical evolution of isolated disc galaxies, we performed a series of 39 gas dynamical simulations of isolated barred and unbarred galaxies with various masses, initial gas fractions, and active galactic nucleus (AGN) feedback models. The presence of a bar drives a substantial amount of gas towards the central region of the galaxy. In the most massive galaxies, this results in a violent starburst, followed by a drop in star formation resulting from gas exhaustion. The time delay between Type Ia and Type II supernovae explosions means that barred galaxies experience a rapid increase in [O/H] in the central region, and a much more gradual increase in [Fe/H]. In unbarred galaxies, star formation proceeds at a slow and steady rate, and oxygen and iron are produced at steady rates which are similar except for a time offset. Comparing the abundance ratios in barred and unbarred galaxies with the same central stellar mass M*, we find in barred galaxies an enhancement of 0.07 dex in [O/H], 0.05 dex in [Fe/H], and 0.05 dex in [O/Fe]. The [O/H] enhancement is in excellent agreement with observations from the SDSS. The initial gas fraction has very little effect on the abundance ratios in barred and unbarred galaxies, unless the galaxies experience a starburst. We considered AGN-host galaxies located near the bottom of the AGN regime, M* ≳ 3 × 1010M⊙, where AGN feedback dominates over supernovae feedback. We found that the impact of AGN feedback on the central abundances is marginal.

Speculations on the dynamics of Jupiter's atmosphere from 1 to 100 bars

NASA Astrophysics Data System (ADS)

Ingersoll, A. P.

2017-12-01

The latitude-altitude map of ammonia mixing ratio shows an ammonia-rich zone at 0-5°N, with mixing ratios of 320-340 ppm, extending from 40-60 bars up to the ammonia cloud base at 0.7 bars. Ammonia-poor air occupies a belt from 5-20°N. We argue that downdrafts as well as updrafts are needed in the 0-5°N zone to balance the upward ammonia flux. Outside the 0-20°N region, the belt-zone signature is weaker. At latitudes out to ±40°, there is an ammonia-rich layer from cloud base down to 2 bars which we argue is caused by falling precipitation. Below, there is an ammonia-poor layer with a minimum at 6 bars. Unanswered questions include how the ammonia-poor layer is maintained, why the belt-zone structure is barely evident in the ammonia distribution outside 0-20°N, and how the internal heat is transported through the ammonia-poor layer to the ammonia cloud base. Here we speculate on possible answers, including double-diffusive convection, deep abyssal overturning, and mass loading of heavy condensates in a hydrogen/helium atmosphere. Ingersoll, A. P. et al. (2017). Implications of the ammonia distribution on Jupiter from 1 to 100 bars as measured by the Juno microwave radiometer. Geophys. Res. Lett., in press, doi: 10.1002/2017GL074277.

Impact of the smoking ban on the volume of bar sales in Ireland: evidence from time series analysis.

PubMed

Cornelsen, Laura; Normand, Charles

2012-05-01

This paper is the first to estimate the economic impact of a comprehensive smoking ban in all enclosed public places of work, on bars in Ireland. The demand in bars, represented by a monthly index of sales volume, is explained by relative prices in bars, prices of alcohol sold in off-licences and the aggregate retail sales (ARS) as a proxy for general economic activity and incomes. The smoking ban is included into the model as a step dummy and the modelling is done using ARIMAX strategy. The results show a reduction in the volume of sales in bars by -4.6% (p<0.01) following the ban. Copyright © 2011 John Wiley & Sons, Ltd.

Role of Erosion in Shaping Point Bars

NASA Astrophysics Data System (ADS)

Moody, J.; Meade, R.

2012-04-01

A powerful metaphor in fluvial geomorphology has been that depositional features such as point bars (and other floodplain features) constitute the river's historical memory in the form of uniformly thick sedimentary deposits waiting for the geomorphologist to dissect and interpret the past. For the past three decades, along the channel of Powder River (Montana USA) we have documented (with annual cross-sectional surveys and pit trenches) the evolution of the shape of three point bars that were created when an extreme flood in 1978 cut new channels across the necks of two former meander bends and radically shifted the location of a third bend. Subsequent erosion has substantially reshaped, at different time scales, the relic sediment deposits of varying age. At the weekly to monthly time scale (i.e., floods from snowmelt or floods from convective or cyclonic storms), the maximum scour depth was computed (by using a numerical model) at locations spaced 1 m apart across the entire point bar for a couple of the largest floods. The maximum predicted scour is about 0.22 m. At the annual time scale, repeated cross-section topographic surveys (25 during 32 years) indicate that net annual erosion at a single location can be as great as 0.5 m, and that the net erosion is greater than net deposition during 8, 16, and 32% of the years for the three point bars. On average, the median annual net erosion was 21, 36, and 51% of the net deposition. At the decadal time scale, an index of point bar preservation often referred to as completeness was defined for each cross section as the percentage of the initial deposit (older than 10 years) that was still remaining in 2011; computations indicate that 19, 41, and 36% of the initial deposits of sediment were eroded. Initial deposits were not uniform in thickness and often represented thicker pods of sediment connected by thin layers of sediment or even isolated pods at different elevations across the point bar in response to multiple

Quantification of Honeycomb Number-Type Stacking Faults: Application to Na 3Ni 2BiO 6 Cathodes for Na-Ion Batteries

DOE PAGES

Liu, Jue; Yin, Liang; Wu, Lijun; ...

2016-08-17

Here, ordered and disordered samples of honeycomb-lattice Na 3Ni 2BiO 6 were investigated as cathodes for Na-ion batteries, and it was determined that the ordered sample exhibits better electrochemical performance, with a specific capacity of 104 mA h/g delivered at plateaus of 3.5 and 3.2 V (vs Na +/Na) with minimal capacity fade during extended cycling. Advanced imaging and diffraction investigations showed that the primary difference between the ordered and disordered samples is the amount of number-type stacking faults associated with the three possible centering choices for each honeycomb layer. A labeling scheme for assigning the number position of honeycombmore » layers is described, and it is shown that the translational shift vectors between layers provide the simplest method for classifying different repeat patterns. We demonstrate that the number position of honeycomb layers can be directly determined in high-angle annular dark-field scanning transmission electron microscopy (STEM-HAADF) imaging studies. By the use of fault models derived from STEM studies, it is shown that both the sharp, symmetric subcell peaks and the broad, asymmetric superstructure peaks in powder diffraction patterns can be quantitatively modeled. About 20% of the layers in the ordered monoclinic sample are faulted in a nonrandom manner, while the disordered sample stacking is not fully random but instead contains about 4% monoclinic order. Furthermore, it is shown that the ordered sample has a series of higher-order superstructure peaks associated with 6-, 9-, 12-, and 15-layer periods whose existence is transiently driven by the presence of long-range strain that is an inherent consequence of the synthesis mechanism revealed through the present diffraction and imaging studies. This strain is closely associated with a monoclinic shear that can be directly calculated from cell lattice parameters and is strongly correlated with the degree of ordering in the samples. The present

Quantification of Honeycomb Number-Type Stacking Faults: Application to Na 3Ni 2BiO 6 Cathodes for Na-Ion Batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Jue; Yin, Liang; Wu, Lijun

Here, ordered and disordered samples of honeycomb-lattice Na 3Ni 2BiO 6 were investigated as cathodes for Na-ion batteries, and it was determined that the ordered sample exhibits better electrochemical performance, with a specific capacity of 104 mA h/g delivered at plateaus of 3.5 and 3.2 V (vs Na +/Na) with minimal capacity fade during extended cycling. Advanced imaging and diffraction investigations showed that the primary difference between the ordered and disordered samples is the amount of number-type stacking faults associated with the three possible centering choices for each honeycomb layer. A labeling scheme for assigning the number position of honeycombmore » layers is described, and it is shown that the translational shift vectors between layers provide the simplest method for classifying different repeat patterns. We demonstrate that the number position of honeycomb layers can be directly determined in high-angle annular dark-field scanning transmission electron microscopy (STEM-HAADF) imaging studies. By the use of fault models derived from STEM studies, it is shown that both the sharp, symmetric subcell peaks and the broad, asymmetric superstructure peaks in powder diffraction patterns can be quantitatively modeled. About 20% of the layers in the ordered monoclinic sample are faulted in a nonrandom manner, while the disordered sample stacking is not fully random but instead contains about 4% monoclinic order. Furthermore, it is shown that the ordered sample has a series of higher-order superstructure peaks associated with 6-, 9-, 12-, and 15-layer periods whose existence is transiently driven by the presence of long-range strain that is an inherent consequence of the synthesis mechanism revealed through the present diffraction and imaging studies. This strain is closely associated with a monoclinic shear that can be directly calculated from cell lattice parameters and is strongly correlated with the degree of ordering in the samples. The present

THE ORION H ii REGION AND THE ORION BAR IN THE MID-INFRARED

DOE Office of Scientific and Technical Information (OSTI.GOV)

Salgado, F.; Tielens, A. G. G. M.; Berné, O.

2016-10-20

We present mid-infrared photometry of the Orion bar obtained with the Faint Object infraRed Camera for the SOFIA Telescope (FORCAST) on board SOFIA at 6.4, 6.6, 7.7, 19.7, 31.5, and 37.1 μ m. By complementing this observation with archival FORCAST and Herschel /PACS images, we are able to construct a complete infrared spectral energy distribution of the Huygens region in the Orion nebula. Comparing the infrared images with gas tracers, we find that PACS maps trace the molecular cloud, while the FORCAST data trace the photodissociation region (PDR) and the H ii region. Analysis of the energetics of the regionmore » reveal that the PDR extends for 0.28 pc along the line of sight and that the bar is inclined at an angle of 4°. The infrared and submillimeter images reveal that the Orion bar represents a swept-up shell with a thickness of 0.1 pc. The mass of the shell implies a shock velocity of ≃3 km s{sup −1} and an age of ≃10{sup 5} years for the H ii region. Our analysis shows that the UV and infrared dust opacities in the H ii region and the PDR are a factor 5 to 10 lower than in the diffuse interstellar medium. In the ionized gas, Ly α photons are a major source of dust heating at distances larger than ≃0.06 pc from θ {sup 1} Ori C. Dust temperatures can be explained if the size of the grains is between 0.1 and 1 μ m. We derive the photoelectric heating efficiency of the atomic gas in the Orion bar. The results are in good qualitative agreement with models and the quantitative differences indicate a decreased polycyclic aromatic hydrocarbon abundance in this region.« less

Mild hydrothermal crystal growth of new uranium(IV) fluorides, Na3.13Mg1.43U6F30 and Na2.50Mn1.75U6F30: Structures, optical and magnetic properties

NASA Astrophysics Data System (ADS)

Yeon, Jeongho; Smith, Mark D.; Tapp, Joshua; Möller, Angela; zur Loye, Hans-Conrad

2016-04-01

Two new uranium(IV) fluorides, Na3.13Mg1.43U6F30 (1) and Na2.50Mn1.75U6F30 (2), were synthesized through an in situ mild hydrothermal route, and were structurally characterized by single crystal X-ray diffraction. The compounds exhibit complex crystal structures composed of corner- or edge-shared UF9 and MF6 (M=Mg, Mn) polyhedra, forming hexagonal channels in the three-dimensional framework, in which ordered or disordered divalent metal and sodium atoms reside. The large hexagonal voids contain the nearly regular M(II)F6 octahedra and sodium ions, whereas the small hexagonal cavities include M(II) and sodium ions on a mixed-occupied site. Magnetic susceptibility measurements yielded effective magnetic moments of 8.36 and 11.6 μB for 1 and 2, respectively, confirming the presence and oxidation states of U(IV) and Mn(II). The large negative Weiss constants indicate the spin gap between a triplet and a singlet state in the U(IV). Magnetization data as a function of applied fields revealed that 2 exhibits paramagnetic behavior due to the nonmagnetic singlet ground state of U(IV) at low temperature. UV-vis diffuse reflectance and X-ray photoelectron spectroscopy data were also analyzed.

STELLAR, GAS, AND DARK MATTER CONTENT OF BARRED GALAXIES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cervantes Sodi, Bernardo, E-mail: b.cervantes@crya.unam.mx

We select a sample of galaxies from the Sloan Digital Sky Survey Data Release 7 (SDSS-DR7) where galaxies are classified, through visual inspection, as hosting strong bars, weak bars, or as unbarred galaxies, and make use of H i mass and kinematic information from the Arecibo Legacy Fast ALFA survey catalog, to study the stellar, atomic gas, and dark matter content of barred disk galaxies. We find, in agreement with previous studies, that the bar fraction increases with increasing stellar mass. A similar trend is found with total baryonic mass, although the dependence is not as strong as with stellarmore » mass, due to the contribution of gas. The bar fraction shows a decrease with increasing gas mass fraction. This anticorrelation between the likelihood of a galaxy hosting a bar with the gas richness of the galaxy results from the inhibiting effect the gas has in the formation of bars. We also find that for massive galaxies with stellar masses larger than 10{sup 10} M {sub ⊙}, at fixed stellar mass, the bar fraction decreases with increasing global halo mass (i.e., halo mass measured up to a radius of the order of the H i disk extent).« less

Insulin activates single amiloride-blockable Na channels in a distal nephron cell line (A6).

PubMed

Marunaka, Y; Hagiwara, N; Tohda, H

1992-09-01

Using the patch-clamp technique, we studied the effect of insulin on an amiloride-blockable Na channel in the apical membrane of a distal nephron cell line (A6) cultured on permeable collagen films for 10-14 days. NPo (N, number of channels per patch membrane; Po, average value of open probability of individual channels in the patch) under baseline conditions was 0.88 +/- 0.12 (SE)(n = 17). After making cell-attached patches on the apical membrane which contained Na channels, insulin (1 mU/ml) was applied to the serosal bath. While maintaining the cell-attached patch, NPo significantly increased to 1.48 +/- 0.19 (n = 17; P less than 0.001) after 5-10 min of insulin application. The open probability of Na channels was 0.39 +/- 0.01 (n = 38) under baseline condition, and increased to 0.66 +/- 0.03 (n = 38, P less than 0.001) after addition of insulin. The baseline single-channel conductance was 4pS, and neither the single-channel conductance nor the current-voltage relationship was significantly changed by insulin. These results indicate that insulin increases Na absorption in the distal nephron by increasing the open probability of the amiloride-blockable Na channel.

Needle bar for warp knitting machines

DOEpatents

Hagel, Adolf; Thumling, Manfred

1979-01-01

Needle bar for warp knitting machines with a number of needles individually set into slits of the bar and having shafts cranked to such an extent that the head section of each needle is in alignment with the shaft section accommodated by the slit. Slackening of the needles will thus not influence the needle spacing.

Bar Study Stories. Issues in Prevention

ERIC Educational Resources Information Center

Higher Education Center for Alcohol, Drug Abuse, and Violence Prevention, 2012

2012-01-01

This issue of "Issues in Prevention" focuses on the impact of the availability of drinks in licensed establishments, such as bars and taverns on student drinking. This issue contains the following articles: (1) Cheap Drinks at College Bars Can Escalate Student Drinking (John D. Clapp); (2) High Alcohol Outlet Density: A Problem for Campuses and…

Knockdown of sodium channel NaV1.6 blocks mechanical pain and abnormal bursting activity of afferent neurons in inflamed sensory ganglia

PubMed Central

Xie, Wenrui; Strong, Judith A.; Ye, Ling; Mao, Ju-Xian; Zhang, Jun-Ming

2013-01-01

Inflammatory processes in the sensory ganglia contribute to many forms of chronic pain. We previously showed that local inflammation of the lumbar sensory ganglia rapidly leads to prolonged mechanical pain behaviors and high levels of spontaneous bursting activity in myelinated cells. Abnormal spontaneous activity of sensory neurons occurs early in many preclinical pain models, and initiates many other pathological changes, but its molecular basis is not well understood. The sodium channel isoform NaV1.6 can underlie repetitive firing and excitatory persistent and resurgent currents. We used in vivo knockdown of this channel via local injection of siRNA to examine its role in chronic pain following local inflammation of the rat lumbar sensory ganglia. In normal DRG, quantitative PCR showed that cells capable of firing repetitively had significantly higher relative expression of NaV1.6. In inflamed DRG, spontaneously active bursting cells expressed high levels of NaV1.6′ immunoreactivity. In vivo knockdown of NaV1.6 locally in the lumbar DRG at the time of DRG inflammation completely blocked development of pain behaviors and abnormal spontaneous activity, while having only minor effects on unmyelinated C-cells. Current research on isoform-specific sodium channel blockers for chronic pain is largely focused on NaV1.8, because it is present primarily in unmyelinated C fiber nociceptors, or on NaV1.7, because lack of this channel causes congenital indifference to pain. However, the results suggest that NaV1.6 may be a useful therapeutic target for chronic pain, and that some pain conditions may be primarily mediated by myelinated A-fiber sensory neurons. PMID:23622763

kW-class diode laser bars

NASA Astrophysics Data System (ADS)

Strohmaier, S. G.; Erbert, G.; Meissner-Schenk, A. H.; Lommel, M.; Schmidt, B.; Kaul, T.; Karow, M.; Crump, P.

2017-02-01

Progress will be presented on ongoing research into the development of ultra-high power and efficiency bars achieving significantly higher output power, conversion efficiency and brightness than currently commercially available. We combine advanced InAlGaAs/GaAs-based epitaxial structures and novel lateral designs, new materials and superior cooling architectures to enable improved performance. Specifically, we present progress in kilowatt-class 10-mm diode laser bars, where recent studies have demonstrated 880 W continuous wave output power from a 10 mm x 4 mm laser diode bar at 850 A of electrical current and 15°C water temperature. This laser achieves < 60% electro-optical efficiency at 880 W CW output power.

Secondhand smoke exposure in bars and restaurants in Guatemala City: before and after smoking ban evaluation.

PubMed

Barnoya, Joaquin; Arvizu, Mariel; Jones, Miranda R; Hernandez, Juan C; Breysse, Patrick N; Navas-Acien, Ana

2011-01-01

In February 2009, Guatemala implemented a comprehensive smoking ban. We assessed air nicotine levels in bars and restaurants 6 months after the ban (post-ban) and compared them with levels found in 2006 (pre-ban). Exposure was estimated by passive sampling of vapor-phase nicotine using samplers (n=50) placed for 7 working days in 10 bars and 11 restaurants in Guatemala City. Air nicotine was measured by gas chromatography, and the time-weighted average concentration in μg/m(3) was estimated. Employees answered a survey about smoke-free workplaces (n = 32) and compared with pre-ban (n = 37) results. Nicotine was detectable in all bars pre- and post-ban. In restaurants, it was detectable in all pre- and 73% post-ban. Median nicotine concentrations in bars significantly decreased from 4.58 μg/m(3) (IQR, 1.71, 6.45) pre-ban to 0.28 μg/m(3) (IQR 0.17, 0.66) post-ban (87% decrease). In restaurants, concentrations significantly decreased from 0.58 μg/m(3) (IQR, 0.44, 0.71) to 0.04 μg/m(3) (IQR 0.01, 0.11) (95% decrease). Employees' support for a smoke-free workplace increased in the post-ban survey (from 32 to 81%, p < 0.001). Six months after the implementation of a smoke-free law in Guatemala, nicotine levels were significantly decreased in bars and restaurants and workers' support for the law substantially increased.

Fatigue of reinforcing bars during hydro-demolition

NASA Astrophysics Data System (ADS)

Hyland, C. W. K.; Ouwejan, A.

2017-05-01

Reinforcing steel fractured during hydro-demolition of a reinforced concrete pier head due to low cycle flexural fatigue from vibration caused by impact of the high pressure water jet on the exposed length of the bars. Research into the fatigue performance of steel reinforcing steel tends to focus on the high cycle axial performance in reinforced concrete members and re-bending behaviour. However with the increasing use of hydro-demolition of concrete structures as part of remediation works care is required to ensure the steel reinforcement exposed to the high pressure jet of water is not going to suffer relatively low cycle flexural damage that may compromise the designed performance of the completed reinforced concrete structure. This paper describes the failure assessment, fatigue analysis, and metallographic examination that was undertaken. It was found that the rib to flank transition radius on the reinforcement steel was small enough to cause a significant stress concentration effect and was the location of fatigue crack growth. A relatively simple analysis using the maximum unrestrained cantilevered bar length and force exerted by the water jet was used to calculate the maximum expected bending moment. This was compared to the bending capacity at initiation of yielding at the rib flank transition accounting for stress concentration effects. This showed that the observed cyclic reversing ductile crack growth and fracture of the H25 bars was consistent with the loading applied. A method is proposed based on these observations to assess suitable limits for unrestrained bar lengths or maximum working offset of the water jet from the point of bar restraint when undertaking hydro-demolition work. The fatigue critical performance requirements of AS/NZS4671 500E bars are also therefore compared with those of BS4449:2005 and PN EN/ISO 15630-1:2011 for comparable 500C bars

Do Low Surface Brightness Galaxies Host Stellar Bars?

NASA Astrophysics Data System (ADS)

Cervantes Sodi, Bernardo; Sánchez García, Osbaldo

2017-09-01

With the aim of assessing if low surface brightness galaxies host stellar bars and by studying the dependence of the occurrence of bars as a function of surface brightness, we use the Galaxy Zoo 2 data set to construct a large volume-limited sample of galaxies and then segregate these galaxies as having low or high surface brightness in terms of their central surface brightness. We find that the fraction of low surface brightness galaxies hosting strong bars is systematically lower than that found for high surface brightness galaxies. The dependence of the bar fraction on the central surface brightness is mostly driven by a correlation of the surface brightness with the spin and the gas richness of the galaxies, showing only a minor dependence on the surface brightness. We also find that the length of the bars is strongly dependent on the surface brightness, and although some of this dependence is attributed to the gas content, even at a fixed gas-to-stellar mass ratio, high surface brightness galaxies host longer bars than their low surface brightness counterparts, which we attribute to an anticorrelation of the surface brightness with the spin.

Do Low Surface Brightness Galaxies Host Stellar Bars?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cervantes Sodi, Bernardo; Sánchez García, Osbaldo, E-mail: b.cervantes@irya.unam.mx, E-mail: o.sanchez@irya.unam.mx

With the aim of assessing if low surface brightness galaxies host stellar bars and by studying the dependence of the occurrence of bars as a function of surface brightness, we use the Galaxy Zoo 2 data set to construct a large volume-limited sample of galaxies and then segregate these galaxies as having low or high surface brightness in terms of their central surface brightness. We find that the fraction of low surface brightness galaxies hosting strong bars is systematically lower than that found for high surface brightness galaxies. The dependence of the bar fraction on the central surface brightness ismore » mostly driven by a correlation of the surface brightness with the spin and the gas richness of the galaxies, showing only a minor dependence on the surface brightness. We also find that the length of the bars is strongly dependent on the surface brightness, and although some of this dependence is attributed to the gas content, even at a fixed gas-to-stellar mass ratio, high surface brightness galaxies host longer bars than their low surface brightness counterparts, which we attribute to an anticorrelation of the surface brightness with the spin.« less

Dynamic tensile characterization of a 4330 steel with kolsky bar techniques.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Song, Bo; Antoun, Bonnie R.; Connelly, Kevin

2010-08-01

There has been increasing demand to understand the stress-strain response as well as damage and failure mechanisms of materials under impact loading condition. Dynamic tensile characterization has been an efficient approach to acquire satisfactory information of mechanical properties including damage and failure of the materials under investigation. However, in order to obtain valid experimental data, reliable tensile experimental techniques at high strain rates are required. This includes not only precise experimental apparatus but also reliable experimental procedures and comprehensive data interpretation. Kolsky bar, originally developed by Kolsky in 1949 [1] for high-rate compressive characterization of materials, has been extended formore » dynamic tensile testing since 1960 [2]. In comparison to Kolsky compression bar, the experimental design of Kolsky tension bar has been much more diversified, particularly in producing high speed tensile pulses in the bars. Moreover, instead of directly sandwiching the cylindrical specimen between the bars in Kolsky bar compression bar experiments, the specimen must be firmly attached to the bar ends in Kolsky tensile bar experiments. A common method is to thread a dumbbell specimen into the ends of the incident and transmission bars. The relatively complicated striking and specimen gripping systems in Kolsky tension bar techniques often lead to disturbance in stress wave propagation in the bars, requiring appropriate interpretation of experimental data. In this study, we employed a modified Kolsky tension bar, newly developed at Sandia National Laboratories, Livermore, CA, to explore the dynamic tensile response of a 4330-V steel. The design of the new Kolsky tension bar has been presented at 2010 SEM Annual Conference [3]. Figures 1 and 2 show the actual photograph and schematic of the Kolsky tension bar, respectively. As shown in Fig. 2, the gun barrel is directly connected to the incident bar with a coupler. The

Improved Kolsky tension bar for high-rate tensile characterization of materials

NASA Astrophysics Data System (ADS)

Song, Bo; Antoun, Bonnie R.; Connelly, Kevin; Korellis, John; Lu, Wei-Yang

2011-04-01

A new Kolsky tension bar has been re-designed and developed at Sandia National Laboratories, CA. The new design uses the concept that a solid striker is fired to impact an end cap attached to the open end of the gun barrel to generate dynamic tensile loading. The gun barrel here serves as part of the loading device. The incident bar that is connected to the gun barrel and the transmission bar follow the design similar to the Kolsky compression bar. The bar supporting and aligning systems are the same as those in the Kolsky compression bar design described by Song et al (2009 Meas. Sci. Technol. 20 115701). Due to the connection complication among the gun barrel, bars and specimen, stress-wave propagation in the new Kolsky tension bar system is comprehensively analyzed. Based on the stress-wave analysis, the strain gage location on the incident bar needs to be carefully determined. A highly precise laser-beam measurement system is recommended to directly measure the displacement of the incident bar end. Dynamic tensile characterization of a 4330-V steel using this new Kolsky tension bar is presented as an example.

Stiffness Matrix of Thin-Walled Open Bar Subject to Bending, Bending Torsion and Shift of Cross Section Middle Surface

NASA Astrophysics Data System (ADS)

Panasenko, N. N.; Sinelschikov, A. V.

2017-11-01

One of the main stages in the analysis of complex 3D structures and engineering constructions made of thin-walled open bars using FEM is a stiffness matrix developing. Taking into account middle surface shear deformation caused by the work of tangential stresses in the formula to calculate a potential energy of thin-walled open bars, the authors obtain an important correction at calculation of the bar deformation and fundamental frequencies. The results of the analysis of the free end buckling of a cantilever H-bar under plane bending differ from exact solution by 0.53%. In the course of comparison of the obtained results with the cantilever bar buckling regardless the middle surface shear deformation, an increase made 16.6%. The stiffness matrix of a thin-walled open bar developed in the present work can be integrated into any software suite using FEM for the analysis of complex 3-D structures and engineering constructions with n-freedoms.

Bar Frequency & Galaxy Host Properties using the Spitzer Survey of Stellar Structure in Galaxies (S4G)

NASA Astrophysics Data System (ADS)

Sheth, Kartik; Mizusawa, T.; Kim, T.; Munoz-Mateos, J.; Regan, M. W.; de Swardt, B.; Gadotti, D.; S4G Team

2011-01-01

Using the volume limited sample of 2,331 nearby galaxies from the Spitzer Survey of Stellar Structure in Galaxies (S4G), we have classified the frequency of barred spiral galaxies. The literature abounds with frequency ranges from as low as 20% to as high as 80% but these variations are driven by the quality of the data, the sample size and the methodology of the studies. Using the 3.6 and 4.5 micron IRAC images from S4G, we are able to make a definitive measurement of the local bar fraction as a function of the galaxy host and environment. We present the results from this survey and discuss how the current bar fraction compares to the declining frequency of bars from the present day to z 1.

A Review of the Biomechanical Differences Between the High-Bar and Low-Bar Back-Squat.

PubMed

Glassbrook, Daniel J; Helms, Eric R; Brown, Scott R; Storey, Adam G

2017-09-01

Glassbrook, DJ, Helms, ER, Brown, SR, and Storey, AG. A review of the biomechanical differences between the high-bar and low-bar back-squat. J Strength Cond Res 31(9): 2618-2634, 2017-The back-squat is a common exercise in strength and conditioning for a variety of sports. It is widely regarded as a fundamental movement to increase and measure lower-body and trunk function, as well as an effective injury rehabilitation exercise. There are typically 2 different bar positions used when performing the back-squat: the traditional "high-bar" back-squat (HBBS) and the "low-bar" back-squat (LBBS). Different movement strategies are used to ensure that the center of mass remains in the base of support for balance during the execution of these lifts. These movement strategies manifest as differences in (a) joint angles, (b) vertical ground reaction forces, and (c) the activity of key muscles. This review showed that the HBBS is characterized by greater knee flexion, lesser hip flexion, a more upright torso, and a deeper squat. The LBBS is characterized by greater hip flexion and, therefore, a greater forward lean. However, there are limited differences in vertical ground reaction forces between the HBBS and LBBS. The LBBS can also be characterized by a greater muscle activity of the erector spinae, adductors, and gluteal muscles, whereas the HBBS can be characterized by greater quadriceps muscle activity. Practitioners seeking to develop the posterior-chain hip musculature (i.e., gluteal, hamstring, and erector muscle groups) may seek to use the LBBS. In comparison, those seeking to replicate movements with a more upright torso and contribution from the quadriceps may rather seek to use the HBBS in training.

Magnetic ground state of the layered honeycomb compound Na2Co2TeO6

NASA Astrophysics Data System (ADS)

Bera, A. K.; Yusuf, S. M.

2018-04-01

The magnetic correlations in the 2D layered honeycomb compound Na2Co2TeO6 has been investigated. The temperature dependent susceptibility curve reveals a transition to the magnetically ordered state at TN ˜ 25 K. The temperature dependent neutron diffraction study confirms an antiferromagnetic ordering below TN. The magnetic ground state is determined to be a zigzag antiferromagnet that appears due to competing exchange interactions beyond nearest neighbors. The moments align along the crystallographic b axis with reduced ordered magnetic moment values of 2.72(2) μB/Co2+ and 2.52(3) μB/Co2+ for two Co sites, respectively. In comparison to the theoretical phase diagram the determined zigzag antiferromagnetic ground state suggests that the compound Na2Co2TeO6 is situated in the proximity to the quantum spin liquid state in the phase diagram.

Scaleable multi-format QCW pump stacks based on 200W laser diode bars and mini bars at 808nm and 940nm

NASA Astrophysics Data System (ADS)

Berk, Yuri; Karni, Yoram; Klumel, Genady; Openhaim, Yaakov; Cohen, Shalom; Yanson, Dan

2011-03-01

Advanced solid state laser architectures place increasingly demanding requirements on high-brightness, low-cost QCW laser diode pump sources, with custom apertures both for side and end rod pumping configurations. To meet this need, a new series of scaleable pump sources at 808nm and 940nm was developed. The stacks, available in multiple output formats, allow for custom aperture filling by varying both the length and quantity of stacked laser bars. For these products, we developed next-generation laser bars based on improved epitaxial wafer designs delivering power densities of 20W/mm of emission aperture. With >200W of peak QCW power available from a full-length 1cm bar, we have demonstrated power scaling to over 2kW in 10-bar stacks with 55% wall plug efficiency. We also present the design and performance of several stack configurations using full-length and reduced-length (mini) bars that demonstrate the versatility of both the bar and packaging designs. We illustrate how the ROBUST HEAD packaging technology developed at SCD is capable of accommodating variable bar length, pitch and quantity for custom rod pumping geometries. The excellent all-around performance of the stacks is supported by reliability data in line with the previously reported 20 Gshot space-grade qualification of SCD's stacks.

A young person's game: immersion and distancing in bar work.

PubMed

Conway, Thomas; MacNeela, Pádraig

2012-01-01

Previous research indicates that bar workers report high levels of alcohol consumption, but the bar work experience itself has been little studied as a means to understand health threats associated with this job role. The subjective experience and meaning of bar work was explored in this study by interviewing current and ex-bar workers from a district in an Irish city that had a high density of bars and busy tourism industry. A total of 12 participants took part in focus groups (FGs) and seven in individual interviews. Four themes were identified in a thematic analysis. The central depiction of bar work was of an initial immersion in an intensive lifestyle characterised by heavy drinking, with subsequent distancing from the extremes of the lifestyle. The participants affiliated strongly with the bar work occupational identity, which included alcohol use in group scenarios for drinking during work, after work and on time off. The bar work lifestyle was most intense in the 'superpub' environment, characterised by permissive staff drinking norms and reported stress. Although an important identity, bar work was ultimately a transient role. The findings are considered in relation to research on occupation-specific stress and alcohol use, social identity and developmental needs in young adulthood.

NaYF{sub 4}:Er,Yb/Bi{sub 2}MoO{sub 6} core/shell nanocomposite: A highly efficient visible-light-driven photocatalyst utilizing upconversion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sun, Yuanyuan; Wang, Wenzhong, E-mail: wzwang@mail.sic.ac.cn; Sun, Songmei

2014-04-01

Highlights: • Design and synthesis of NaYF{sub 4}:Er,Yb/Bi{sub 2}MoO{sub 6} based on upconversion. • NaYF{sub 4}:Er,Yb/Bi{sub 2}MoO{sub 6} nanocomposite was prepared for the first time. • Core–shell structure benefits the properties. • Upconversion contributed to the enhanced photocatalytic activity. • Helps to understand the functionality of new type photocatalysts. - Abstract: NaYF{sub 4}:Er,Yb/Bi{sub 2}MoO{sub 6} core/shell nanocomposite was designed and prepared for the first time based on upconversion. The products were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), high resolution TEM (HRTEM), energy dispersive X-ray spectroscopy (EDS) and diffuse reflectance spectra (DRS). The results revealed that the as-synthesizedmore » NaYF{sub 4}:Er,Yb/Bi{sub 2}MoO{sub 6} consisted of spheres with a core diameter of about 26 nm and a shell diameter of around 6 nm. The core was upconversion illuminant NaYF{sub 4}:Er,Yb and the shell was Bi{sub 2}MoO{sub 6} around the core, which was confirmed by EDS. The NaYF{sub 4}:Er,Yb/Bi{sub 2}MoO{sub 6} exhibited higher photocatalytic activity for the photodecomposition of Rhodamine B (RhB) under the irradiation of Xe lamp and green light emitting diode (g-LED). The mechanism of the high photocatalytic activity was discussed by photoluminescence spectra (PL), which is mainly attributed to upconversion of NaYF{sub 4}:Er,Yb in the NaYF{sub 4}:Er,Yb/Bi{sub 2}MoO{sub 6} nanocomposite and the core–shell structure.« less

Finite Element Simulations to Explore Assumptions in Kolsky Bar Experiments.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crum, Justin

2015-08-05

The chief purpose of this project has been to develop a set of finite element models that attempt to explore some of the assumptions in the experimental set-up and data reduction of the Kolsky bar experiment. In brief, the Kolsky bar, sometimes referred to as the split Hopkinson pressure bar, is an experimental apparatus used to study the mechanical properties of materials at high strain rates. Kolsky bars can be constructed to conduct experiments in tension or compression, both of which are studied in this paper. The basic operation of the tension Kolsky bar is as follows: compressed air ismore » inserted into the barrel that contains the striker; the striker accelerates towards the left and strikes the left end of the barrel producing a tensile stress wave that propogates first through the barrel and then down the incident bar, into the specimen, and finally the transmission bar. In the compression case, the striker instead travels to the right and impacts the incident bar directly. As the stress wave travels through an interface (e.g., the incident bar to specimen connection), a portion of the pulse is transmitted and the rest reflected. The incident pulse, as well as the transmitted and reflected pulses are picked up by two strain gauges installed on the incident and transmitted bars as shown. By interpreting the data acquired by these strain gauges, the stress/strain behavior of the specimen can be determined.« less

New Defective Brannerite-Type Vanadates. I. Synthesis and Study of Mn 1- x- yφ xNa yV 2-2 x-yMo 2 x+yO 6 Solid Solutions

NASA Astrophysics Data System (ADS)

Masłowska, Bogna; Ziółkowski, Jacek

1994-05-01

MnV 2O 6 of the brannerite-type structure (below 540°C) doped with MoO 3 and Na 2O forms isomorphous solid solutions MnNaφ = Mn 1- x-yφ xNa yV 2-2 x-yMo 2 x+ yO 6 (φ cation vacancy in the original Mn position), belonging to the pseudoternary MnV 2O 6-NaVMoO 6-MoO 3 system. Particular cases are MnNa = Mn 1- yNa y V 2- yMo yO 6 ( x = 0), Mnφ = Mn 1- xφ xV 2-2 xMo 2 xO 6 ( y = 0), and Naφ = Na 1- xφ xV 1- xMo 1+ xO 6 ( x + y = 1). MnV 2O 6 and NaVMoO 6 show miscibility in the entire composition range (MnNa). The opposite boundary of MnNaφ passes through the (100 x, 100 y) points (45, 0), (33, 30), and (30, 70). The phase diagram of the pseudobinary MnV 2O 6-NaVMoO 6 system (determined with DTA) shows (i) a narrow double-lens-type solidus-liquidus gap at high values of y , (ii) two peritectic meltings at lower y (yielding the high temperature β-MnNa and Mn 2V 2O 7), and (iii) little area of β-MnNa. Lattice parameters of MnNa (determined with X-ray diffraction) reveal small deviations from Vegard's law. As the ionic radii of both dopants (Na + and Mo 6+) are, respectively, larger than those of mother ions (Mn 2+ and V 5+), the unit cell increases in all directions with rising y along the MnNa series of solid solutions. However, due to the anisotropy of the structure, parameter c is strongly sensitive to Na/Mn substitution, b is ruled by Mo/V, and a is weakly influenced by Mo/V. Close analogy to the behavior of the previously studied MnV 2O 6-LiVMoO 6-MoO 6 system is discussed.

The study of two barred galaxies with curious kinematical features

NASA Astrophysics Data System (ADS)

Saburova, A. S.; Katkov, I. Y.; Khoperskov, S. A.; Zasov, A. V.; Uklein, R. I.

2017-09-01

We performed long-slit spectral observations of two SB-type galaxies: NGC 5347 and UGC 1344. They were previously suspected as the galaxies with unusually low mass-to-light ratios (on the ground of mass estimates from the H I linewidths), which are in conflict with their observed colours. The observations were conducted at the Russian 6-m telescope. The aim of this study was to clarify the kinematics and structure, as well as the properties of stellar populations of the galaxies. The results of observations disproved the peculiarly low mass-to-light ratios of both galaxies. The most probable reasons of underestimation of their masses are discussed. We tried to reproduce the main observed features of kinematical profiles of the galaxies in the N-body simulations of barred galaxies. We found that both galaxies possess central components of different structures. Indeed, the age and velocity dispersion of stellar population in NGC 5347 are low in its innermost part in comparison to that of the bulge or a bar, which agrees with the presence of nuclear kinematically decoupled disc. It probably was formed due to the bar that supplied the inner region with gas. The kinematical profiles of the second galaxy UGC 1344 give evidence in favour of the central peanut-shaped bulge. In spite of the different luminosities of the two galaxies, they possess nearly equal (close to solar) central stellar abundance and the flattening of the stellar metallicity gradient in the bar regions. However, in the less luminous NGC 5347, the mean stellar age is younger than that in UGC 1344.

The company they keep: drinking group attitudes and male bar aggression.

PubMed

Dumas, Tara M; Graham, Kathryn; Wells, Samantha

2015-05-01

The purpose of this study was to assess (a) similarities in self-reported bar-aggression-related attitudes and behaviors among members of young male groups recruited on their way to bars and (b) group-level variables associated with individual members' self-reported likelihood of perpetrating physical bar aggression in the past year, controlling for individual attitudes. Young, male, natural drinking groups recruited on their way to a bar district Thursday, Friday, and Saturday nights (n = 167, 53 groups) completed an online survey that measured whether they had perpetrated physical aggression at a bar in the past year and constructs associated with bar aggression, including attitudes toward male bar aggression and frequency of heavy episodic drinking in the past year. Intraclass correlations and chi-square tests demonstrated significant within-group similarity on bar-aggression-related attitudes and behaviors (ps < .01). Hierarchical linear modeling revealed that group attitudes toward bar aggression were significantly associated with individuals' likelihood of perpetrating physical bar aggression, controlling for individual attitudes (p < .01); however, the link between group heavy episodic drinking and self-reported bar aggression was nonsignificant in the full model. This study suggests that the most important group influence on young men's bar aggression is the attitudes of other group members. These attitudes were associated with group members' likelihood of engaging in bar aggression over and above individuals' own attitudes. A better understanding of how group attitudes and behavior affect the behavior of individual group members is needed to inform aggression-prevention programming.

Dynamics of membrane nanotubes coated with I-BAR

NASA Astrophysics Data System (ADS)

Barooji, Younes F.; Rørvig-Lund, Andreas; Semsey, Szabolcs; Reihani, S. Nader S.; Bendix, Poul M.

2016-07-01

Membrane deformation is a necessary step in a number of cellular processes such as filopodia and invadopodia formation and has been shown to involve membrane shaping proteins containing membrane binding domains from the IRSp53-MIM protein family. In reconstituted membranes the membrane shaping domains can efficiently deform negatively charged membranes into tubules without any other proteins present. Here, we show that the IM domain (also called I-BAR domain) from the protein ABBA, forms semi-flexible nanotubes protruding into Giant Unilamellar lipid Vesicles (GUVs). By simultaneous quantification of tube intensity and tubular shape we find both the diameter and stiffness of the nanotubes. I-BAR decorated tubes were quantified to have a diameter of ~50 nm and exhibit no stiffening relative to protein free tubes of the same diameter. At high protein density the tubes are immobile whereas at lower density the tubes diffuse freely on the surface of the GUV. Bleaching experiments of the fluorescently tagged I-BAR confirmed that the mobility of the tubes correlates with the mobility of the I-BAR on the GUV membrane. Finally, at low density of I-BAR the protein upconcentrates within tubes protruding into the GUVs. This implies that I-BAR exhibits strong preference for negatively curved membranes.

Cultural Factors Related to Smoking in San Francisco's Irish Bars

ERIC Educational Resources Information Center

Satterlund, Travis D.; Antin, Tamar M. J.; Lee, Juliet P.; Moore, Roland S.

2009-01-01

California's Smoke-Free Workplace Act was extended to include bars in 1998. While the majority of bars in the state have become smoke free, in many bars patrons and staff continue to smoke despite the law. The authors present findings from a study which assessed cultural factors related to continued smoking in bars in the city of San Francisco. In…

Gaseous Vortices in Barred Spiral Galaxies

NASA Technical Reports Server (NTRS)

England, Martin N.; Hunter, James H., Jr.

1995-01-01

During the course of examining many two-dimensional, as well as a smaller sample of three-dimensional, models of gas flows in barred spiral galaxies, we have been impressed by the ubiquitous presence fo vortex pairs, oriented roughly perpendicular to their bars, with one vortex on each side. The vortices are obvious only when viewed in the bar frame, and the centers of their velocity fields usually are near Lagrangian points L(sub 4,5). In all models that we have studied, the vortices form on essentially the same time scale as that for the development of gaseous spiral arms, typically two bar rotations. Usually the corotation radius, r(sub c), lies slightly beyond the end of the bar. Depending upon the mass distributions of the various components, gas spirals either into, or out of, the vortices: In the former case, the vortices become regions of high density, whereas the opposite is true if the gas spirals out of a vortex. The models described in this paper have low-density vortices, as do most of the models we have studied. Moreover, usually the vortex centers lie approximately within +/- 15 deg of L(sub 4,5). In the stellar dynamic limit, when pressure and viscous forces are absent, short-period orbits exist, centered on L(sub 4,5). These orbits need not cross and therefore their morphology is that of gas streamlines, that is, vortices. We believe that the gas vortices in our models are hydrodynamic analogues of closed, short-period, libration orbits centered on L(sub 4,5).

Lmo1656 is a secreted virulence factor of Listeria monocytogenes that interacts with the sorting nexin 6-BAR complex.

PubMed

David, Daryl Jason; Pagliuso, Alessandro; Radoshevich, Lilliana; Nahori, Marie-Anne; Cossart, Pascale

2018-06-15

Listeria monocytogenes ( Lm ) is a facultative intracellular bacterial pathogen and the causative agent of listeriosis, a rare but fatal disease. During infection, Lm can traverse several physiological barriers; it can cross the intestine and placenta barrier and, in immunocompromised individuals, the blood-brain barrier. With the recent plethora of sequenced genomes available for Lm , it is clear that the complete repertoire of genes used by Lm to interact with its host remains to be fully explored. Recently, we focused on secreted Lm proteins because they are likely to interact with host cell components. Here, we investigated a putatively secreted protein of Lm , Lmo1656, that is present in most sequenced strains of Lm but absent in the nonpathogenic species Listeria innocua. lmo1656 gene is predicted to encode a small, positively charged protein. We show that Lmo1656 is secreted by Lm Furthermore, deletion of the lmo1656 gene (Δ lmo1656 ) attenuates virulence in mice infected orally but not intravenously, suggesting that Lmo1656 plays a role during oral listeriosis. We identified sorting nexin 6 (SNX6), an endosomal sorting component and BAR domain-containing protein, as a host cell interactor of Lmol656. SNX6 colocalizes with WT Lm during the early steps of infection. This colocalization depends on Lmo1656, and RNAi of SNX6 impairs infection in infected tissue culture cells, suggesting that SNX6 is utilized by Lm during infection. Our results reveal that Lmo1656 is a novel secreted virulence factor of Lm that facilitates recruitment of a specific member of the sorting nexin family in the mammalian host. © 2018 by The American Society for Biochemistry and Molecular Biology, Inc.

Sol-gel polydimethylsiloxane/poly(vinylalcohol)-coated stir bar sorptive extraction of organophosphorus pesticides in honey and their determination by large volume injection GC.

PubMed

Yu, Chunhe; Hu, Bin

2009-01-01

A PDMS/poly(vinylalcohol) (PDMS/PVA) film prepared through a sol-gel process was coated on stir bars for sorptive extraction, followed by liquid desorption and large volume injection-GC-flame photometric detector (LVI-GC-FPD) for the determination of five organophosphorus pesticides (OPPs) (phorate, fenitrothion, malathion, parathion, and quinalphos) in honey. The preparation reproducibility of PDMS/PVA-coated stir bar ranged from 4.3 to 13.4% (n = 4) in one batch, and from 6.0 to 12.6% (n = 4) in batch to batch. And one prepared stir bar can be used for more than 50 times without apparent coating loss. The significant parameters affecting stir bar sorptive extraction (SBSE) were investigated and optimized. The LODs for five OPPs ranged from 0.013 (parathion) to 0.081 microg/L (phorate) with the RSDs ranging from 5.3 to 14.2% (c = 1 microg/L, n = 6). The proposed method was successfully applied to the analysis of five OPPs in honey.

12 CFR 380.32 - Claims bar date.

Code of Federal Regulations, 2012 CFR

2012-01-01

... LIQUIDATION AUTHORITY Receivership Administrative Claims Process § 380.32 Claims bar date. Upon its appointment as receiver for a covered financial company, the Corporation as receiver shall establish a claims bar date by which date creditors of the covered financial company shall present their claims, together...

21 CFR 886.5800 - Ophthalmic bar reader.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Ophthalmic bar reader. 886.5800 Section 886.5800 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES OPHTHALMIC DEVICES Therapeutic Devices § 886.5800 Ophthalmic bar reader. (a...

Bar-Code System for a Microbiological Laboratory

NASA Technical Reports Server (NTRS)

Law, Jennifer; Kirschner, Larry

2007-01-01

A bar-code system has been assembled for a microbiological laboratory that must examine a large number of samples. The system includes a commercial bar-code reader, computer hardware and software components, plus custom-designed database software. The software generates a user-friendly, menu-driven interface.

33 CFR 13.01-45 - Replacement of medals and bars.

Code of Federal Regulations, 2014 CFR

2014-07-01

... SECURITY GENERAL DECORATIONS, MEDALS, RIBBONS AND SIMILAR DEVICES Gold and Silver Lifesaving Medals, Bars, and Miniatures § 13.01-45 Replacement of medals and bars. The Gold or Silver Lifesaving Medal or bar...

33 CFR 13.01-45 - Replacement of medals and bars.

Code of Federal Regulations, 2011 CFR

2011-07-01

... SECURITY GENERAL DECORATIONS, MEDALS, RIBBONS AND SIMILAR DEVICES Gold and Silver Lifesaving Medals, Bars, and Miniatures § 13.01-45 Replacement of medals and bars. The Gold or Silver Lifesaving Medal or bar...

33 CFR 13.01-45 - Replacement of medals and bars.

Code of Federal Regulations, 2010 CFR

2010-07-01

... SECURITY GENERAL DECORATIONS, MEDALS, RIBBONS AND SIMILAR DEVICES Gold and Silver Lifesaving Medals, Bars, and Miniatures § 13.01-45 Replacement of medals and bars. The Gold or Silver Lifesaving Medal or bar...

33 CFR 13.01-45 - Replacement of medals and bars.

Code of Federal Regulations, 2012 CFR

2012-07-01

... SECURITY GENERAL DECORATIONS, MEDALS, RIBBONS AND SIMILAR DEVICES Gold and Silver Lifesaving Medals, Bars, and Miniatures § 13.01-45 Replacement of medals and bars. The Gold or Silver Lifesaving Medal or bar...

33 CFR 13.01-45 - Replacement of medals and bars.

Code of Federal Regulations, 2013 CFR

2013-07-01

... SECURITY GENERAL DECORATIONS, MEDALS, RIBBONS AND SIMILAR DEVICES Gold and Silver Lifesaving Medals, Bars, and Miniatures § 13.01-45 Replacement of medals and bars. The Gold or Silver Lifesaving Medal or bar...

Polydimethylsiloxane/MIL-100(Fe) coated stir bar sorptive extraction-high performance liquid chromatography for the determination of triazines in environmental water samples.

PubMed

Lei, Yun; Chen, Beibei; You, Linna; He, Man; Hu, Bin

2017-12-01

Polydimethylsiloxane (PDMS)/MIL-100(Fe) coated stir bar was prepared by sol gel technique, and good preparation reproducibility was achieved with relative standard deviations (RSDs) ranging from 2.6% to 7.5% (n=7) and 3.6% to 10.8% (n=7) for bar-to-bar and batch-to-batch, respectively. Compared with commercial PDMS coated stir bar (Gerstel) and PEG coated stir bar (Gerstel), the prepared PDMS/MIL-100(Fe) stir bar showed better extraction efficiency for target triazines compounds. It also exhibited relatively fast extraction/desorption kinetics and long lifespan. Based on it, a method of PDMS/MIL-100(Fe) coated stir bar sorptive extraction (SBSE)-high performance liquid chromatography-ultraviolet detector (HPLC-UV) was developed for the determination of six triazines (simazine, atrazine, prometon, ametryn, prometryne and prebane) in environmental water samples. Several parameters affecting SBSE of six target triazines including extraction time, stirring rate, sample pH, ionic strength, desorption solvent and desorption time were investigated. Under the optimal experimental conditions, the limits of detection (LODs, S/N=3) were found to be in the range of 0.021-0.079μgL -1 . The repeatability RSDs were in the range of 2.3-6.3% (n=7, c=0.5μgL -1 ) and the enrichment factors (EFs) ranged from 51.1 to 102-fold (theoretical EF was 200-fold). The proposed method was applied to the analysis of target triazines in environmental water samples, with recoveries of 98.0-118% and 94.0-107% for spiked East Lake water and local pond water samples, respectively. Copyright © 2017. Published by Elsevier B.V.

Hader bar and clip attachment retained mandibular complete denture

PubMed Central

Singh, Kunwarjeet; Gupta, Nidhi; Kapoor, Vikram; Gupta, Ridhimaa

2013-01-01

Bar and clip attachments significantly improve the level of satisfaction of denture-wearing patients by enhancing the retention and stability of the prosthesis. These attachments have been most commonly used for connecting the prosthesis to implants, but they can be effectively used to retain tooth-supported prosthesis as well. The primary functions of bar attachments are splinting the abutments together, even distribution of forces to the abutments and supporting areas, guiding the prosthesis into place, improving the retention, stability, support and comfort of the patient. The primary requirement for the use of bar attachments is the availability of sufficient vertical and buccolingual space for the proper placement of the bar, sleeves, teeth arrangement and sufficient thickness of acrylic denture base to minimise incidence of denture fracture in the area of bar assembly. PMID:24145505

Hader bar and clip attachment retained mandibular complete denture.

PubMed

Singh, Kunwarjeet; Gupta, Nidhi; Kapoor, Vikram; Gupta, Ridhimaa

2013-10-21

Bar and clip attachments significantly improve the level of satisfaction of denture-wearing patients by enhancing the retention and stability of the prosthesis. These attachments have been most commonly used for connecting the prosthesis to implants, but they can be effectively used to retain tooth-supported prosthesis as well. The primary functions of bar attachments are splinting the abutments together, even distribution of forces to the abutments and supporting areas, guiding the prosthesis into place, improving the retention, stability, support and comfort of the patient. The primary requirement for the use of bar attachments is the availability of sufficient vertical and buccolingual space for the proper placement of the bar, sleeves, teeth arrangement and sufficient thickness of acrylic denture base to minimise incidence of denture fracture in the area of bar assembly.

Study of aging and embrittlement of microalloyed steel bars

NASA Astrophysics Data System (ADS)

Campillo, B.; Perez, R.; Martinez, L.

1996-10-01

The aging of hooks, anchors, and other bent reinforcing steel bars in concrete structures are considered in modern international standards. Rebend test procedures have been designed in order to predict the aging embrittlement susceptibility by submerging bent reinforcing bar specimens in boiling water. Subsequently the bars are rebent or straightened in order to determine the loss of ductility or embrittlement of the aged material. The present work considers the influence of carbon, sulfur, and niobium on the performance of reinforcing bars in rebend tests of 300 heats of microalloyed steel bars with a variety of compositions. The microstructural evidence and the statistical results clearly indicate the strong influence of carbon and sulfur on rebend failure, while niobium-rich precipitates contribute to the hardening of the ferrite grains during aging.

The effect of 8.25% sodium hypochlorite on dental pulp dissolution and dentin flexural strength and modulus.

PubMed

Cullen, James K T; Wealleans, James A; Kirkpatrick, Timothy C; Yaccino, John M

2015-06-01

The purpose of this study was to evaluate the effect of various concentrations of sodium hypochlorite (NaOCl), including 8.25%, on dental pulp dissolution and dentin flexural strength and modulus. Sixty dental pulp samples and 55 plane parallel dentin bars were retrieved from extracted human teeth. Five test groups (n = 10) were formed consisting of a pulp sample and dentin bar immersed in various NaOCl solutions. The negative control group (n = 5) consisted of pulp samples and dentin bars immersed in saline. The positive control group (n = 5) consisted of pulp samples immersed in 8.25% NaOCl without a dentin bar. Every 6 minutes for 1 hour, the solutions were refreshed. The dentin bars were tested for flexural strength and modulus with a 3-point bend test. The time until total pulp dissolution and any changes in dentin bar flexural strength and modulus for the different NaOCl solutions were statistically analyzed. An increase in NaOCl concentration showed a highly significant decrease in pulp dissolution time. The pulp dissolution property of 8.25% NaOCl was significantly faster than any other tested concentration of NaOCl. The presence of dentin did not have a significant effect on the dissolution capacity of NaOCl if the solutions were refreshed. NaOCl concentration did not have a statistically significant effect on dentin flexural strength or modulus. Dilution of NaOCl decreases its pulp dissolution capacity. Refreshing the solution is essential to counteract the effects of dentin. In this study, NaOCl did not have a significant effect on dentin flexural strength or modulus. Published by Elsevier Inc.

33 CFR 13.01-10 - Gold and silver bars.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Gold and silver bars. 13.01-10... DECORATIONS, MEDALS, RIBBONS AND SIMILAR DEVICES Gold and Silver Lifesaving Medals, Bars, and Miniatures § 13.01-10 Gold and silver bars. No person shall receive more than one Gold Lifesaving Medal and one...

33 CFR 13.01-10 - Gold and silver bars.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 1 2011-07-01 2011-07-01 false Gold and silver bars. 13.01-10... DECORATIONS, MEDALS, RIBBONS AND SIMILAR DEVICES Gold and Silver Lifesaving Medals, Bars, and Miniatures § 13.01-10 Gold and silver bars. No person shall receive more than one Gold Lifesaving Medal and one...

33 CFR 13.01-10 - Gold and silver bars.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 1 2013-07-01 2013-07-01 false Gold and silver bars. 13.01-10... DECORATIONS, MEDALS, RIBBONS AND SIMILAR DEVICES Gold and Silver Lifesaving Medals, Bars, and Miniatures § 13.01-10 Gold and silver bars. No person shall receive more than one Gold Lifesaving Medal and one...

33 CFR 13.01-10 - Gold and silver bars.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 33 Navigation and Navigable Waters 1 2012-07-01 2012-07-01 false Gold and silver bars. 13.01-10... DECORATIONS, MEDALS, RIBBONS AND SIMILAR DEVICES Gold and Silver Lifesaving Medals, Bars, and Miniatures § 13.01-10 Gold and silver bars. No person shall receive more than one Gold Lifesaving Medal and one...

33 CFR 13.01-10 - Gold and silver bars.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 33 Navigation and Navigable Waters 1 2014-07-01 2014-07-01 false Gold and silver bars. 13.01-10... DECORATIONS, MEDALS, RIBBONS AND SIMILAR DEVICES Gold and Silver Lifesaving Medals, Bars, and Miniatures § 13.01-10 Gold and silver bars. No person shall receive more than one Gold Lifesaving Medal and one...

Measurement of the top quark mass in the $$t\\bar{t}\\rightarrow\\text{ lepton+jets }$$→ and $$t\\bar{t}\\rightarrow\\text{dilepton}$$ → channels using $$\\sqrt{s}=7$$TeV ATLAS data

DOE PAGES

Aad, G.; Abbott, B.; Abdallah, J.; ...

2015-07-17

The top quark mass was measured in the channelsmore » $$t\\bar{t}$$→ lepton+jets and $$t\\bar{t}$$→ dilepton (lepton = e,μ) based on ATLAS data recorded in 2011. The data were taken at the LHC with a proton–proton centre-of-mass energy of √s = 7 TeV and correspond to an integrated luminosity of 4.6 fb –1. The $$t\\bar{t}$$→ lepton+jets analysis uses a three-dimensional template technique which determines the top quark mass together with a global jet energy scale factor (JSF), and a relative b-to-light-jet energy scale factor (bJSF), where the terms b-jets and light-jets refer to jets originating from b-quarks and u, d, c, s-quarks or gluons, respectively. The analysis of the $$t\\bar{t}$$→ dilepton channel exploits a one-dimensional template method using the m ℓb observable, defined as the average invariant mass of the two lepton+b-jet pairs in each event. The top quark mass is measured to be 172.33 ± 0.75 (stat + JSF + bJSF) ± 1.02(syst) GeV, and 173.79 ± 0.54(stat) ± 1.30(syst) GeV in the $$t\\bar{t}$$→ lepton+jets and $$t\\bar{t}$$→ dilepton channels, respectively. Thus, the combination of the two results yields m top = 172.99 ± 0.48(stat) ± 0.78(syst) GeV, with a total uncertainty of 0.91 GeV.« less

BarA-UvrY two-component system regulates virulence of uropathogenic E. coli CFT073.

PubMed

Palaniyandi, Senthilkumar; Mitra, Arindam; Herren, Christopher D; Lockatell, C Virginia; Johnson, David E; Zhu, Xiaoping; Mukhopadhyay, Suman

2012-01-01

Uropathogenic Escherichia coli (UPEC), a member of extraintestinal pathogenic E. coli, cause ∼80% of community-acquired urinary tract infections (UTI) in humans. UPEC initiates its colonization in epithelial cells lining the urinary tract with a complicated life cycle, replicating and persisting in intracellular and extracellular niches. Consequently, UPEC causes cystitis and more severe form of pyelonephritis. To further understand the virulence characteristics of UPEC, we investigated the roles of BarA-UvrY two-component system (TCS) in regulating UPEC virulence. Our results showed that mutation of BarA-UvrY TCS significantly decreased the virulence of UPEC CFT073, as assessed by mouse urinary tract infection, chicken embryo killing assay, and cytotoxicity assay on human kidney and uroepithelial cell lines. Furthermore, mutation of either barA or uvrY gene reduced the production of hemolysin, lipopolysaccharide (LPS), proinflammatory cytokines (TNF-α and IL-6) and chemokine (IL-8). The virulence phenotype was restored similar to that of wild-type by complementation of either barA or uvrY gene in trans. In addition, we discussed a possible link between the BarA-UvrY TCS and CsrA in positively and negatively controlling virulence in UPEC. Overall, this study provides the evidences for BarA-UvrY TCS regulates the virulence of UPEC CFT073 and may point to mechanisms by which virulence regulations are observed in different ways may control the long-term survival of UPEC in the urinary tract.

Modified sine bar device measures small angles with high accuracy

NASA Technical Reports Server (NTRS)

Thekaekara, M.

1968-01-01

Modified sine bar device measures small angles with enough accuracy to calibrate precision optical autocollimators. The sine bar is a massive bar of steel supported by two cylindrical rods at one end and one at the other.

Low temperature heat capacity and thermodynamic functions of anion bearing sodalites Na 8Al 6Si 6O 24X 2 (X = SO 4, ReO 4, Cl, I)

DOE PAGES

Schliesser, Jacob; Lilova, Kristina; Pierce, Eric M.; ...

2017-06-01

Heat capacities of sulfate, perrhenate, chloride, and iodide sodalites with the ideal formula Na 8Al 6Si 6O 24X 2 (X = SO 4, ReO 4, Cl, I) were measured from 2 K to 300 K using a Quantum Design Physical Property Measurement System (PPMS). From the heat capacity data, the standard thermodynamic functions were determined. All four sodalites undergo a phase transition below room temperature for which thermodynamic parameters were determined. Additionally, the heat capacity of one of the constituent compounds (NaReO 4) was measured.

An anatomical study of the pterygospinous bar and foramen of Civinini.

PubMed

Goyal, Neeru; Jain, Anjali

2016-10-01

The pterygospinous ligament extends from the posterior free margin of the lateral pterygoid plate till the spine of the sphenoid. The ligament may ossify partly or completely leading to the formation of the pterygospinous bar. A complete ossification of the ligament results in the formation of the foramen of Civinini. Presence of the complete or incomplete pterygospinous bar may lead to a difficulty in passing the needle during anaesthesia for the trigeminal neuralgia or the bar may also compress the mandibular nerve and its branches to cause lingual numbness, pain and speech impairment. Presence of the complete or incomplete pterygospinous bar and the foramen of Civinini were studied in 55 dried adult skulls and 20 sphenoid bones. Partial or complete ossification of the pterygospinous ligament was seen in 17.33 % skulls. One skull showed the presence of bilateral complete pterygospinous bar while another skull had the unilateral complete pterygospinous bar on right side. Two skulls and one sphenoid had bilateral incomplete pterygospinous bar while seven skulls and one sphenoid bone had unilateral incomplete pterygospinous bar. In three cases, the bar was passing just below the foramen ovale. The pterygospinous bar when present medial to the foramen ovale may not have much clinical significance but when the bar is present just below the foramen ovale, it may cause a compression of the mandibular nerve and its branches and may also obstruct the passage for the transoval approach to the neighbouring regions.

An exploratory study of drug use in bar environments

PubMed Central

Trocki, Karen; Michalak, Laurence; McDaniel, Patricia

2010-01-01

The purpose of this paper is to explore the characteristics of bars where drug use was observed compared to those where no drug use was observed. The study was done through a combination of qualitative and quantitative techniques gleaned through observations and interviews. Among the most important of indicators were the type of activity (particularly dancing) and the level of rowdiness evident in the bars. In addition drug use bars had higher levels of other types of rule-breaking. Patron characteristics (more men) and behavioral patterns (more sexual risk-taking) also distinguished these bars. PMID:25221431

50 CFR Figures 14a and 14b to Part... - Maximum Angle of Deflector Bars With Straight Bars Attached to the Bottom of the Frame and...

Code of Federal Regulations, 2010 CFR

2010-10-01

... 50 Wildlife and Fisheries 7 2010-10-01 2010-10-01 false Maximum Angle of Deflector Bars With Straight Bars Attached to the Bottom of the Frame and Maximum Angle of Deflector Bars With Bent Bars Attached to the Bottom of the Frame 14a Figures 14a and 14b to Part 223 Wildlife and Fisheries NATIONAL...

50 CFR Figures 14a and 14b to Part... - Maximum Angle of Deflector Bars With Straight Bars Attached to the Bottom of the Frame and...

Code of Federal Regulations, 2011 CFR

2011-10-01

... 50 Wildlife and Fisheries 9 2011-10-01 2011-10-01 false Maximum Angle of Deflector Bars With Straight Bars Attached to the Bottom of the Frame and Maximum Angle of Deflector Bars With Bent Bars Attached to the Bottom of the Frame 14a Figures 14a and 14b to Part 223 Wildlife and Fisheries NATIONAL...

Print media coverage of California's smokefree bar law

PubMed Central

Magzamen, S.; Charlesworth, A.; Glantz, S.

2001-01-01

OBJECTIVE—To assess the print media coverage of California's smokefree bar law in the state of California.
DESIGN—Content analysis of newspaper, trade journal, and magazine items.
SUBJECTS—Items regarding the smokefree bar law published seven months before and one year following the implementation of the smokefree bar law (June 1997 to December 1998). Items consisted of news articles (n = 446), opinion editorials (n = 31), editorials (n = 104), letters to the editor (n = 240), and cartoons (n = 10).
MAIN OUTCOME MEASURES—Number and timing of publication of items, presence of tobacco industry arguments or public health arguments regarding law, positive, negative, and neutral views of opinion items published.
RESULTS—53% of items published concerning the smokefree bar law were news articles, 47% were opinion items. 45% of items regarding the smokefree bar law were published during the first month of implementation. The tobacco industry dominated coverage in most categories (economics, choice, enforcement, ventilation, legislation, individual quotes), except for categories public health used the most frequently (government role, tactics, organisational quotes). Anti-law editorials and letters to the editor were published more than pro-law editorials and letters. Region of the state, paper size, presence of local clean indoor air legislation, and voting on tobacco related ballot initiatives did not have an impact on the presence of opinion items.
CONCLUSIONS—The tobacco industry succeeded in obtaining more coverage of the smokefree bar law, both in news items and opinion items. The tobacco industry used historical arguments of restricting freedom of choice and economic ramifications in fighting the smokefree bar law, while public health groups focused on the worker protection issue, and exposed tobacco industry tactics. Despite the skewed coverage, public health groups obtained adequate attention to their arguments to keep the law in

Evaluation of a responsible beverage service and enforcement program: Effects on bar patron intoxication and potential impaired driving by young adults.

PubMed

Fell, James C; Fisher, Deborah A; Yao, Jie; McKnight, A Scott

2017-08-18

Studies of alcohol-related harm (violence, injury, illness) suggest that the most significant risk factors are the amount of alcohol consumed and whether obviously intoxicated patrons continue to be served. This study's objective was to investigate the effects of a responsible beverage service (RBS)/enhanced alcohol enforcement intervention on bars, bar patrons, and impaired driving. Two communities-Monroe County, New York, and Cleveland, Ohio-participated in a demonstration program and evaluation. The intervention applied RBS training, targeted enforcement, and corrective actions by law enforcement to a random sample of 10 identified problem bars in each community compared to 10 matched nonintervention problem bars. Data were collected over 3 waves on bar serving practices, bar patron intoxication, drinking and driving, and other alcohol-related harm from intervention and control bars and treatment and comparison communities. In Monroe County, New York, of the 14 outcome measures analyzed, 7 measures showed statistically significant differences from pre- to postintervention. Six of those measures indicated changes in the desired or positive direction and 2 measures were in the undesired or negative direction. Of note in the positive direction, the percentage of intervention bar patrons who were intoxicated decreased from 44 to 27% and the average blood alcohol concentration of patrons decreased from 0.097 to 0.059 g/dL pre- to postintervention. In Cleveland, Ohio, 6 of the 14 measures showed statistically significant changes pre- to postintervention with 6 in the positive direction and 4 in the negative direction. Of note, the percentage of pseudo-intoxicated patrons denied service in intervention bars increased from 6 to 29%. Of the 14 outcome measures that were analyzed in each community, most indicated positive changes associated with the intervention, but others showed negative associations. About half of the measures showed no significance, the sample sizes

Bar formation as driver of gas inflows in isolated disc galaxies

NASA Astrophysics Data System (ADS)

Fanali, R.; Dotti, M.; Fiacconi, D.; Haardt, F.

2015-12-01

Stellar bars are a common feature in massive disc galaxies. On a theoretical ground, the response of gas to a bar is generally thought to cause nuclear starbursts and, possibly, AGN activity once the perturbed gas reaches the central supermassive black hole. By means of high-resolution numerical simulations, we detail the purely dynamical effects that a forming bar exerts on the gas of an isolated disc galaxy. The galaxy is initially unstable to the formation of non-axisymmetric structures, and within ˜1 Gyr it develops spiral arms that eventually evolve into a central stellar bar on kpc scale. A first major episode of gas inflow occurs during the formation of the spiral arms while at later times, when the stellar bar is establishing, a low-density region is carved between the bar corotational and inner Lindblad resonance radii. The development of such `dead zone' inhibits further massive gas inflows. Indeed, the gas inflow reaches its maximum during the relatively fast bar-formation phase and not, as often assumed, when the bar is fully formed. We conclude that the low efficiency of long-lived, evolved bars in driving gas towards galactic nuclei is the reason why observational studies have failed to establish an indisputable link between bars and AGNs. On the other hand, the high efficiency in driving strong gas inflows of the intrinsically transient process of bar formation suggests that the importance of bars as drivers of AGN activity in disc galaxies has been overlooked so far. We finally prove that our conclusions are robust against different numerical implementations of the hydrodynamics routinely used in galaxy evolution studies.

Machine learning techniques in searches for$$t\\bar{t}$$h in the h → $$b\\bar{b}$$ decay channel

DOE PAGES

Santos, Robert; Nguyen, M.; Webster, Jordan; ...

2017-04-10

Study of the production of pairs of top quarks in association with a Higgs boson is one of the primary goals of the Large Hadron Collider over the next decade, as measurements of this process may help us to understand whether the uniquely large mass of the top quark plays a special role in electroweak symmetry breaking. Higgs bosons decay predominantly to bmore » $$\\bar{_b}$$, yielding signatures for the signal that are similar to t$$\\bar{_t}$$ + jets with heavy flavor. Though particularly challenging to study due to the similar kinematics between signal and background events, such final states (t$$\\bar{_t}$$b$$\\bar{b}$$) are an important channel for studying the top quark Yukawa coupling. This paper presents a systematic study of machine learning (ML) methods for detecting t$$\\bar{_t}$$h in the h → b$$\\bar{b}$$ decay channel. Among the seven ML methods tested, we show that neural network models outperform alternative methods. In addition, two neural models used in this paper outperform NeuroBayes, one of the standard algorithms used in current particle physics experiments. We further study the effectiveness of ML algorithms by investigating the impact of feature set and data size, as well as the depth of the networks for neural models. We demonstrate that an extended feature set leads to improvement of performance over basic features. Furthermore, the availability of large samples for training is found to be important for improving the performance of the techniques. For the features and the data set studied here, neural networks of more layers deliver comparable performance to their simpler counterparts.« less

Machine learning techniques in searches for$$t\\bar{t}$$h in the h → $$b\\bar{b}$$ decay channel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Santos, Robert; Nguyen, M.; Webster, Jordan

Study of the production of pairs of top quarks in association with a Higgs boson is one of the primary goals of the Large Hadron Collider over the next decade, as measurements of this process may help us to understand whether the uniquely large mass of the top quark plays a special role in electroweak symmetry breaking. Higgs bosons decay predominantly to bmore » $$\\bar{_b}$$, yielding signatures for the signal that are similar to t$$\\bar{_t}$$ + jets with heavy flavor. Though particularly challenging to study due to the similar kinematics between signal and background events, such final states (t$$\\bar{_t}$$b$$\\bar{b}$$) are an important channel for studying the top quark Yukawa coupling. This paper presents a systematic study of machine learning (ML) methods for detecting t$$\\bar{_t}$$h in the h → b$$\\bar{b}$$ decay channel. Among the seven ML methods tested, we show that neural network models outperform alternative methods. In addition, two neural models used in this paper outperform NeuroBayes, one of the standard algorithms used in current particle physics experiments. We further study the effectiveness of ML algorithms by investigating the impact of feature set and data size, as well as the depth of the networks for neural models. We demonstrate that an extended feature set leads to improvement of performance over basic features. Furthermore, the availability of large samples for training is found to be important for improving the performance of the techniques. For the features and the data set studied here, neural networks of more layers deliver comparable performance to their simpler counterparts.« less

Partial entrainment of gravel bars during floods

USGS Publications Warehouse

Konrad, Christopher P.; Booth, Derek B.; Burges, Stephen J.; Montgomery, David R.

2002-01-01

Spatial patterns of bed material entrainment by floods were documented at seven gravel bars using arrays of metal washers (bed tags) placed in the streambed. The observed patterns were used to test a general stochastic model that bed material entrainment is a spatially independent, random process where the probability of entrainment is uniform over a gravel bar and a function of the peak dimensionless shear stress τ0* of the flood. The fraction of tags missing from a gravel bar during a flood, or partial entrainment, had an approximately normal distribution with respect to τ0* with a mean value (50% of the tags entrained) of 0.085 and standard deviation of 0.022 (root‐mean‐square error of 0.09). Variation in partial entrainment for a given τ0* demonstrated the effects of flow conditioning on bed strength, with lower values of partial entrainment after intermediate magnitude floods (0.065 < τ0*< 0.08) than after higher magnitude floods. Although the probability of bed material entrainment was approximately uniform over a gravel bar during individual floods and independent from flood to flood, regions of preferential stability and instability emerged at some bars over the course of a wet season. Deviations from spatially uniform and independent bed material entrainment were most pronounced for reaches with varied flow and in consecutive floods with small to intermediate magnitudes.

Dynamic tensile characterization of a 4330-V steel with kolsky bar techniques.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Song, Bo; Antoun, Bonnie R.; Connelly, Kevin

2010-09-01

There has been increasing demand to understand the stress-strain response as well as damage and failure mechanisms of materials under impact loading condition. Dynamic tensile characterization has been an efficient approach to acquire satisfactory information of mechanical properties including damage and failure of the materials under investigation. However, in order to obtain valid experimental data, reliable tensile experimental techniques at high strain rates are required. This includes not only precise experimental apparatus but also reliable experimental procedures and comprehensive data interpretation. Kolsky bar, originally developed by Kolsky in 1949 [1] for high-rate compressive characterization of materials, has been extended formore » dynamic tensile testing since 1960 [2]. In comparison to Kolsky compression bar, the experimental design of Kolsky tension bar has been much more diversified, particularly in producing high speed tensile pulses in the bars. Moreover, instead of directly sandwiching the cylindrical specimen between the bars in Kolsky bar compression bar experiments, the specimen must be firmly attached to the bar ends in Kolsky tensile bar experiments. A common method is to thread a dumbbell specimen into the ends of the incident and transmission bars. The relatively complicated striking and specimen gripping systems in Kolsky tension bar techniques often lead to disturbance in stress wave propagation in the bars, requiring appropriate interpretation of experimental data. In this study, we employed a modified Kolsky tension bar, newly developed at Sandia National Laboratories, Livermore, CA, to explore the dynamic tensile response of a 4330-V steel. The design of the new Kolsky tension bar has been presented at 2010 SEM Annual Conference [3]. Figures 1 and 2 show the actual photograph and schematic of the Kolsky tension bar, respectively. As shown in Fig. 2, the gun barrel is directly connected to the incident bar with a coupler. The

Membrane curvature and its generation by BAR proteins

PubMed Central

Mim, Carsten; Unger, Vinzenz M

2012-01-01

Membranes are flexible barriers that surround the cell and its compartments. To execute vital functions such as locomotion or receptor turnover, cells need to control the shapes of their membranes. In part, this control is achieved through membrane-bending proteins, such as the bin/amphiphysin/rvs domain (BAR) proteins. Many open questions remain about the mechanisms by which membrane-bending proteins function. Addressing this shortfall, recent structures of BAR protein:membrane complexes support existing mechanistic models, but also produced novel insights into how BAR-domain proteins sense, stabilize and generate curvature. Here we review these recent findings, focusing on how BAR proteins interact with the membrane, and how the resulting scaffold structures might aid the recruitment of other proteins to the sites where membranes are bent. PMID:23058040

Response of saliva Na/K ratio to changing Na supply of lactating cows under tropical conditions.

PubMed

Thiangtum, Wandee; Schonewille, J Thomas; Verstegen, Martin Wa; Arsawakulsudhi, Supot; Rukkwamsuk, Theera; Hendriks, Wouter H

2017-06-01

Factorial determination of the sodium (Na) requirement of heat-stressed lactating cows is hindered by accurate estimates of the Na losses through sweat. Direct studies, therefore, may be needed requiring information on the time course of healthy animals to become Na depleted and the subsequent rate of repletion. The rate of Na depletion and subsequent rate of Na repletion with two levels of dietary Na to lactating dairy cows housed under tropical conditions were investigated using the salivary Na/K. The 12 lactating cows (salivary Na/K ratio 14.6) rapidly developed clinical signs of Na deficiency, including pica, polyuria and polydipsia, reduced body weight and reduced milk yield when fed a low-Na ration (0.33 g kg -1 dry matter (DM)) for 3 weeks. Deficiency symptoms were associated with a rapid decrease in salivary Na/K ratio to <4.3 from 7 to 21 days. Subsequent repletion of the cows with NaCl to a ration concentration of 1.1 or 1.6 g Na kg -1 DM for 5 weeks did not restore salivary Na/K ratio to values of >6. A daily Na intake of heat-stressed lactating cows to a ration intake of 1.6 g Na kg -1 DM was insufficient to restore Na deficiency. One week was sufficient to deplete heat-stressed lactating cows of Na, allowing for rapid dose-response studies utilizing the salivary Na/K ratio as a parameter for Na status of cows under tropical conditions. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Design criteria for panic bars and auger miner safety. Panic bar study. Volume 1. Continuous miners. Open file report (final), 1973-74

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marrus, L.D.; Rogne, C.

1974-01-23

The panic bars (and associated linkages and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on self-propelled, electric and diesel face equipment, including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that are recommended in this document, but all of the panic bars are characteristically of the ''fire door'' type that is frequently encountered on outside exit doors of many public and some commercial buildings. It is also the intent of the following panic bar designs that, whenmore » emergency brakes are added to the face equipment machinery for which they are required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). (GRA)« less

Detection of Dust Condensations in the Orion Bar Photon-dominated Region

NASA Astrophysics Data System (ADS)

Qiu, Keping; Xie, Zeqiang; Zhang, Qizhou

2018-03-01

We report Submillimeter Array dust continuum and molecular spectral line observations toward the Orion Bar photon-dominated region (PDR). The 1.2 mm continuum map reveals, for the first time, a total of nine compact (r < 0.01 pc) dust condensations located within a distance of ∼0.03 pc from the dissociation front of the PDR. Part of the dust condensations are also seen in spectral line emissions of CS (5–4) and H2CS (71,7–61,6), though the CS map also reveals dense gas further away from the dissociation front. We also detect compact emissions in H2CS (60,6–50,5), (62,4–52,3) and C34S, C33S (4–3) toward bright dust condensations. The line ratio of H2CS (60,6–50,5)/(62,4–52,3) suggests a temperature of 73 ± 58 K. A nonthermal velocity dispersion of ∼0.25–0.50 km s‑1 is derived from the high spectral resolution C34S data and indicates a subsonic to transonic turbulence in the condensations. The masses of the condensations are estimated from the dust emission, and range from 0.03 to 0.3 M ⊙, all significantly lower than any critical mass that is required for self-gravity to play a crucial role. Thus the condensations are not gravitationally bound, and could not collapse to form stars. In cooperating with recent high-resolution observations of the compressed surface layers of the molecular cloud in the Bar, we speculate that the condensations are produced as a high-pressure wave induced by the expansion of the H II region compresses and enters the cloud. A velocity gradient along a direction perpendicular to the major axis of the Bar is seen in H2CS (71,7–61,6), and is consistent with the scenario that the molecular gas behind the dissociation front is being compressed.

The BAR Domain Proteins: Molding Membranes in Fission, Fusion, and Phagy

PubMed Central

Ren, Gang; Vajjhala, Parimala; Lee, Janet S.; Winsor, Barbara; Munn, Alan L.

2006-01-01

The Bin1/amphiphysin/Rvs167 (BAR) domain proteins are a ubiquitous protein family. Genes encoding members of this family have not yet been found in the genomes of prokaryotes, but within eukaryotes, BAR domain proteins are found universally from unicellular eukaryotes such as yeast through to plants, insects, and vertebrates. BAR domain proteins share an N-terminal BAR domain with a high propensity to adopt α-helical structure and engage in coiled-coil interactions with other proteins. BAR domain proteins are implicated in processes as fundamental and diverse as fission of synaptic vesicles, cell polarity, endocytosis, regulation of the actin cytoskeleton, transcriptional repression, cell-cell fusion, signal transduction, apoptosis, secretory vesicle fusion, excitation-contraction coupling, learning and memory, tissue differentiation, ion flux across membranes, and tumor suppression. What has been lacking is a molecular understanding of the role of the BAR domain protein in each process. The three-dimensional structure of the BAR domain has now been determined and valuable insight has been gained in understanding the interactions of BAR domains with membranes. The cellular roles of BAR domain proteins, characterized over the past decade in cells as distinct as yeasts, neurons, and myocytes, can now be understood in terms of a fundamental molecular function of all BAR domain proteins: to sense membrane curvature, to bind GTPases, and to mold a diversity of cellular membranes. PMID:16524918

The Role of 2D Circulation in Sand Bar Migration

NASA Astrophysics Data System (ADS)

Splinter, K. D.; Holman, R. A.; Plant, N. G.; Holland, K. T.

2006-12-01

Models of bar dynamics typically involve moments of the cross-shore flow, with offshore movement associated with the strong offshore directed undertow and onshore migration related to wave asymmetry and skewness [Gallagher, et al., 1998]. Based on these hypotheses, models and laboratory studies have used the alongshore-mean bar position and alongshore-uniform wave conditions (a 1DH approach) to study bar response to varying wave conditions. Commonly, cases of offshore migration were reproduced with reasonable accuracy, but predictions of onshore migration were less successful. However, examination of time-exposure images of waves show that during periods of offshore migration, bars tend to be alongshore uniform and move rapidly offshore, but during onshore migration, sand bars are rarely straight, instead becoming very sinuous, violating the 1DH approach. We hypothesize that under milder wave conditions, the 2DH circulation associated with this alongshore-variable morphology is, in fact, largely responsible for increased onshore net sand transport and the resulting onshore bar movement. We extend the work of Plant et al. [in review] that relates bar position, sinuosity, and wave forcing within a dynamical feedback model. The model consists of coupled differential equations that govern the rates of change of cross-shore position and horizontal sinuosity as a function of the current cross-shore position and sinuosity and a proxy for wave forcing. Using a short data set from Duck, NC, they solve for the unknown coupling coefficients by doing a least-squares fit. They find that the coefficients for the self-interaction terms have a negative sign, indicating the overall system is stable. The coefficients of the cross-interaction terms (the effect of sinuosity on rate of change of bar position and visa versa), however, are non-zero and have opposite signs indicating the systems are coupled and stability is not affected by these terms. We expand this study, relating bar

The Na+/K+-ATPase and the amyloid-beta peptide aβ1-40 control the cellular distribution, abundance and activity of TRPC6 channels.

PubMed

Chauvet, Sylvain; Boonen, Marielle; Chevallet, Mireille; Jarvis, Louis; Abebe, Addis; Benharouga, Mohamed; Faller, Peter; Jadot, Michel; Bouron, Alexandre

2015-11-01

The Na(+)/K(+)-ATPase interacts with the non-selective cation channels TRPC6 but the functional consequences of this association are unknown. Experiments performed with HEK cells over-expressing TRPC6 channels showed that inhibiting the activity of the Na(+)/K(+)-ATPase with ouabain reduced the amount of TRPC6 proteins and depressed Ca(2+) entry through TRPC6. This effect, not mimicked by membrane depolarization with KCl, was abolished by sucrose and bafilomycin-A, and was partially sensitive to the intracellular Ca(2+) chelator BAPTA/AM. Biotinylation and subcellular fractionation experiments showed that ouabain caused a multifaceted redistribution of TRPC6 to the plasma membrane and to an endo/lysosomal compartment where they were degraded. The amyloid beta peptide Aβ(1-40), another inhibitor of the Na(+)/K(+)-ATPase, but not the shorter peptide Aβ1-16, reduced TRPC6 protein levels and depressed TRPC6-mediated responses. In cortical neurons from embryonic mice, ouabain, veratridine (an opener of voltage-gated Na(+) channel), and Aβ(1-40) reduced TRPC6-mediated Ca(2+) responses whereas Aβ(1-16) was ineffective. Furthermore, when Aβ(1-40) was co-added together with zinc acetate it could no longer control TRPC6 activity. Altogether, this work shows the existence of a functional coupling between the Na(+)/K(+)-ATPase and TRPC6. It also suggests that the abundance, distribution and activity of TRPC6 can be regulated by cardiotonic steroids like ouabain and the naturally occurring peptide Aβ(1-40) which underlines the pathophysiological significance of these processes. Copyright © 2015 Elsevier B.V. All rights reserved.

Universal precision sine bar attachment

NASA Technical Reports Server (NTRS)

Mann, Franklin D. (Inventor)

1989-01-01

This invention relates to an attachment for a sine bar which can be used to perform measurements during lathe operations or other types of machining operations. The attachment can be used for setting precision angles on vises, dividing heads, rotary tables and angle plates. It can also be used in the inspection of machined parts, when close tolerances are required, and in the layout of precision hardware. The novelty of the invention is believed to reside in a specific versatile sine bar attachment for measuring a variety of angles on a number of different types of equipment.

Comparing Monofractal and Multifractal Analysis of Corrosion Damage Evolution in Reinforcing Bars

PubMed Central

Xu, Yidong; Qian, Chunxiang; Pan, Lei; Wang, Bingbing; Lou, Chi

2012-01-01

Based on fractal theory and damage mechanics, the aim of this paper is to describe the monofractal and multifractal characteristics of corrosion morphology and develop a new approach to characterize the nonuniform corrosion degree of reinforcing bars. The relationship between fractal parameters and tensile strength of reinforcing bars are discussed. The results showed that corrosion mass loss ratio of a bar cannot accurately reflect the damage degree of the bar. The corrosion morphology of reinforcing bars exhibits both monofractal and multifractal features. The fractal dimension and the tensile strength of corroded steel bars exhibit a power function relationship, while the width of multifractal spectrum and tensile strength of corroded steel bars exhibit a linear relationship. By comparison, using width of multifractal spectrum as multifractal damage variable not only reflects the distribution of corrosion damage in reinforcing bars, but also reveals the influence of nonuniform corrosion on the mechanical properties of reinforcing bars. The present research provides a new approach for the establishment of corrosion damage constitutive models of reinforcing bars. PMID:22238682

Near infrared spectra of the Orion bar

NASA Astrophysics Data System (ADS)

Marconi, A.; Testi, L.; Natta, A.; Walmsley, C. M.

1998-02-01

We have used the LONGSP spectrometer on the 1.5-m TIRGO telescope to obtain long slit spectra in the J, H, and K wavelength bands towards two positions along the Orion bar. These data have been supplemented with images made using the ARNICA camera mounted on TIRGO as well as with an ESO NTT observation carried out by Dr A. Moorwood. We detect a variety of transitions of hydrogen, helium, OI, FeII, FeIII, and H_2. From our molecular hydrogen data, we conclude that densities are moderate (3-6x 10(4) cm(-3) ) in the layer responsible for the molecular hydrogen emission and give no evidence for the presence of dense neutral clumps. We also find that the molecular hydrogen bar is likely to be tilted by ~ 10 degrees relative to the line of sight. We discuss the relative merits of several models of the structure of the bar and conclude that it may be split into two structures separated by 0.2-0.3 parsec along the line of sight. It also seems likely to us that in both structures, density increases along a line perpendicular to the ionization front which penetrates into the neutral gas. We have used the 1.317mum OI line to estimate the FUV radiation field incident at the ionization front and find values of 1-3x 10(4) greater than the average interstellar field. From [FeII] line measurements, we conclude that the electron density in the ionized layer associated with the ionization front is of order 10(4) \\percc. Finally, our analysis of the helium and hydrogen recombination lines implies essential coincidence of the helium and hydrogen Stromgren spheres.

DAMPING OF THE MILKY WAY BAR BY MANIFOLD-DRIVEN SPIRALS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Łokas, Ewa L.

2016-10-10

We describe a new phenomenon of “bar damping” that may have played an important role in shaping the Milky Way bar and bulge as well as its spiral structure. We use a collisionless N -body simulation of a Milky Way–like galaxy initially composed of a dark matter halo and an exponential disk with a Toomre parameter slightly above unity. In this configuration, dominated by the disk in the center, a bar forms relatively quickly, after 1 Gyr of evolution. This is immediately followed by the formation of two manifold-driven spiral arms and the outflow of stars that modifies the potentialmore » in the vicinity of the bar, apparently shifting the position of the L {sub 1}/ L {sub 2} Lagrange points. This modification leads to the shortening of the bar and the creation of a next generation of manifold-driven spiral arms at a smaller radius. The process repeats itself a few times over the next 0.5 Gyr resulting in further substantial weakening and shortening of the bar. The time when the damping comes to an end coincides with the first buckling episode in the bar that rebuilds the orbital structure so that no more new spiral arms are formed. The morphology of the bar and the spiral structure at this time show remarkable similarity to the present properties of the Milky Way. Later on, the bar starts to grow rather steadily again, weakened only by subsequent buckling episodes occurring at more distant parts of the disk.« less

Divergent actions of the pyrethroid insecticides S-bioallethrin, tefluthrin, and deltamethrin on rat Na{sub v}1.6 sodium channels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tan Jianguo; Soderlund, David M., E-mail: dms6@cornell.ed

2010-09-15

We expressed rat Na{sub v}1.6 sodium channels in combination with the rat {beta}{sub 1} and {beta}{sub 2} auxiliary subunits in Xenopus laevis oocytes and evaluated the effects of the pyrethroid insecticides S-bioallethrin, deltamethrin, and tefluthrin on expressed sodium currents using the two-electrode voltage clamp technique. S-Bioallethrin, a type I structure, produced transient modification evident in the induction of rapidly decaying sodium tail currents, weak resting modification (5.7% modification at 100 {mu}M), and no further enhancement of modification upon repetitive activation by high-frequency trains of depolarizing pulses. By contrast deltamethrin, a type II structure, produced sodium tail currents that were {approx}more » 9-fold more persistent than those caused by S-bioallethrin, barely detectable resting modification (2.5% modification at 100 {mu}M), and 3.7-fold enhancement of modification upon repetitive activation. Tefluthrin, a type I structure with high mammalian toxicity, exhibited properties intermediate between S-bioallethrin and deltamethrin: intermediate tail current decay kinetics, much greater resting modification (14.1% at 100 {mu}M), and 2.8-fold enhancement of resting modification upon repetitive activation. Comparison of concentration-effect data showed that repetitive depolarization increased the potency of tefluthrin {approx} 15-fold and that tefluthrin was {approx} 10-fold more potent than deltamethrin as a use-dependent modifier of Na{sub v}1.6 sodium channels. Concentration-effect data from parallel experiments with the rat Na{sub v}1.2 sodium channel coexpressed with the rat {beta}{sub 1} and {beta}{sub 2} subunits in oocytes showed that the Na{sub v}1.6 isoform was at least 15-fold more sensitive to tefluthrin and deltamethrin than the Na{sub v}1.2 isoform. These results implicate sodium channels containing the Na{sub v}1.6 isoform as potential targets for the central neurotoxic effects of pyrethroids.« less

An alkaline tin(II) halide compound Na{sub 3}Sn{sub 2}F{sub 6}Cl: Synthesis, structure, and characterization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gong, Pifu; University of the Chinese Academy of Sciences, Beijing 100049; Luo, Siyang

A new alkali tin(II) halide compound, Na{sub 3}Sn{sub 2}F{sub 6}Cl, is synthesized by hydrothermal method. This compound crystallizes trigonally in space group of R-3c (167), and processes a zero-dimensional (0D) structure consisted of Na{sup +} cations, Cl{sup −} anions and the isolated [SnF{sub 3}]{sup -} trigonal pyramids in which the stereochemically active 5s{sup 2} lone pair electrons are attached to the Sn{sup 2+} cations. Interestingly, the [SnF{sub 3}]{sup −} trigonal pyramids are parallel arranged in the a-b plane, while oppositely arranged in line with rotation along the c- axis. Moreover, the energy bandgap, thermal stability and electronic structure of Na{submore » 3}Sn{sub 2}F{sub 6}Cl are characterized and the results reveal that this compound has and indirect bandgap of 3.88 eV and is stable under 270 °C. - Graphical abstract: A zero-dimensional alkaline tin halide compound, Na{sub 3}Sn{sub 2}F{sub 6}Cl, is synthesized by hydrothermal method. Interestingly, both the anions and cations coordinating polyhedra exhibit order arranged with the [SnF{sub 3}]{sup -} trigonal pyramids rotating along the c- axis.« less

Stress-strain relationship of high-strength steel (HSS) reinforcing bars

NASA Astrophysics Data System (ADS)

Anggraini, Retno; Tavio, Raka, I. Gede Putu; Agustiar

2018-05-01

The introduction of High-Strength Steel (HSS) reinforcing bars in reinforced concrete members has gained much attention in recent years and led to many advantages such as construction timesaving. It is also more economical since it can reduce the amount of reinforcing steel bars used in concrete members which in turn alleviates the congestion of reinforcement. Up to present, the building codes, e.g. American Concrete Institute (ACI) 318M-14 and Standard National Indonesia (SNI) 2847:2013, still restrict the use of higher-strength steel reinforcing bars for concrete design up to Grade 420 MPa due to the possible suspected brittle behavior of concrete members. This paper evaluates the characteristics of stress-strain relationships of HSS bars if they are comparable to the characteristics of those of Grade 420 MPa. To achieve the objective of the study, a series of steel bars from various grades (420, 550, 650, and 700 MPa) was selected. Tensile tests of these steel samples were conducted under displacement-controlled mode to capture the complete stress-strain curves and particularly the post-yield response of the steel bars. The results indicate that all the steel bars tested had the actual yield strengths greater than the corresponding specified values. The stress-strain curves of HSS reinforcing bars (Grade 550, 650, and 700 MPa) performed slightly different characteristics with those of Grade 420 MPa.

Defining the formative discharge for alternate bars in alluvial rivers

NASA Astrophysics Data System (ADS)

Redolfi, M.; Carlin, M.; Tubino, M.; Adami, L.; Zolezzi, G.

2017-12-01

We investigate the properties of alternate bars in long straight reaches of channelized streams subject to an unsteady, irregular flow regime. To this aim we propose a novel integration of a statistical approach with the analytical perturbation model of Tubino (1991) which predicts the evolution of bar properties (namely amplitude and wavelength) as consequence of a flood. The outcomes of our integrated modelling approach are probability distribution of the bar properties, which depend essentially on two ingredients: (i) the statistical properties of the flow regime (duration, frequency and magnitude of the flood events, and (ii) the reach-averaged hydro-geomorphic characteristics of the channel (bed material, channel gradient and width). This allows to define a "bar-forming" discharge value as the flow value which would reproduce the most likely bar properties in a river reach under unsteady flow. Alternate bars are often migrating downstream and growing or declining during flood events. The timescale of bar growth and migration is often comparable with the duration of the floods: consequently, bar properties such as height and wavelength do not respond instantaneously to discharge variations (i.e. quasi-equilibrium response) but may depend on previous flood events. Theoretical results are compared with observations in three Alpine, channelized gravel bed rivers with encouraging outcomes.

Pressure induced coordination change of Al in silicate melts from Al K edge XANES of high pressure NaAlSi2O6-NaAlSi3O8 glasses

NASA Astrophysics Data System (ADS)

Li, Dien; Secco, R. A.; Bancroft, G. M.; Fleet, M. E.

Aluminum K-edge XANES spectra of high pressure and high temperature (4.4 GPa and 1575°C) glasses along the NaAlSi2O6 (Jd)-NaAlSi3O8 (Ab) join are reported using synchrotron radiation, and shown to provide direct experimental evidence for the pressure-induced coordination change of Al. Five- and six-fold coordinated Al (5Al and 6Al), characterized by Al K-edge positions at 1567.8 and 1568.7 eV, respectively, first appear in glass of composition Jd60Ab40 and increase in proportion progressively with increasing Jd content. The end-member jadeite glass contains about 6% of each of 5Al and 6Al. The present direct measurements confirm literature suggestions for the important role of Al in controlling viscosity and diffusion in mantle melts.

Sediment storage time in a simulated meandering river's floodplain, comparisons of point bar and overbank deposits

NASA Astrophysics Data System (ADS)

Ackerman, T. R.; Pizzuto, J. E.

2016-12-01

Sediment may be stored briefly or for long periods in alluvial deposits adjacent to rivers. The duration of sediment storage may affect diagenesis, and controls the timing of sediment delivery, affecting the propagation of upland sediment signals caused by tectonics, climate change, and land use, and the efficacy of watershed management strategies designed to reduce sediment loading to estuaries and reservoirs. Understanding the functional form of storage time distributions can help to extrapolate from limited field observations and improve forecasts of sediment loading. We simulate stratigraphy adjacent to a modeled river where meander migration is driven by channel curvature. The basal unit is built immediately as the channel migrates away, analogous to a point bar; rules for overbank (flood) deposition create thicker deposits at low elevations and near the channel, forming topographic features analogous to natural levees, scroll bars, and terraces. Deposit age is tracked everywhere throughout the simulation, and the storage time is recorded when the channel returns and erodes the sediment at each pixel. 210 ky of simulated run time is sufficient for the channel to migrate 10,500 channel widths, but only the final 90 ky are analyzed. Storage time survivor functions are well fit by exponential functions until 500 years (point bar) or 600 years (overbank) representing the youngest 50% of eroded sediment. Then (until an age of 12 ky, representing the next 48% (point bar) or 45% (overbank) of eroding sediment), the distributions are well fit by heavy tailed power functions with slopes of -1 (point bar) and -0.75 (overbank). After 12 ky (6% of model run time) the remainder of the storage time distributions become exponential (light tailed). Point bar sediment has the greatest chance (6%) of eroding at 120 years, as the river reworks recently deposited point bars. Overbank sediment has an 8% chance of eroding after 1 time step, a chance that declines by half after 3

Hydrothermal alteration of graywacke and basalt by 4 molal NaCl.

USGS Publications Warehouse

Rosenbauer, R.J.; Bischoff, J.L.; Radtke, A.S.

1983-01-01

Rock-water interaction experiments were carried out at 350oC and 500 bar at a 1/10 rock/fluid ratio using 4 molal NaCl brine. Reaction of brine and greywacke lead to the conversion of illite, dolomite and quartz to albite and smectite. In the process, the rock gained Na and released Ca, K, heavy metals and CO2 to solution. Metal mobilization was found to primarily depend on acidity which was produced by Na metasomatism and by dedolomitization. Reaction of brine and basalt produced only minor alteration in which some smectite and little albite formed. No significant acidity was produced nor did metals become mobilized. Production of acidity during albitization depends entirely on the phase being altered. Albitization of greywacke produces H+ whereas the albitization of basalt apparently consumes this ion. -J.E.S.

Alcohol Mixed with Energy Drink Use as an Event-Level Predictor of Physical and Verbal Aggression in Bar Conflicts.

PubMed

Miller, Kathleen E; Quigley, Brian M; Eliseo-Arras, Rebecca K; Ball, Natalie J

2016-01-01

Young adult use of alcohol mixed with caffeinated energy drinks (AmEDs) has been globally linked with increased odds of interpersonal aggression, compared with the use of alcohol alone. However, no prior research has linked these behaviors at the event level in bar drinking situations. The present study assessed whether AmED use is associated with the perpetration of verbal and physical aggression in bar conflicts at the event level. In Fall 2014, a community sample of 175 young adult AmED users (55% female) completed a web survey describing a recent conflict experienced while drinking in a bar. Use of both AmED and non-AmED alcoholic drinks in the incident were assessed, allowing calculation of our main predictor variable, the proportion of AmEDs consumed (AmED/total drinks consumed). To measure perpetration of aggression, participants reported on the occurrence of 6 verbal and 6 physical acts during the bar conflict incident. Linear regression analyses showed that the proportion of AmEDs consumed predicted scores for perpetration of both verbal aggression (β = 0.16, p < 0.05) and physical aggression (β = 0.19, p < 0.01) after controlling for gender, age, sensation-seeking and aggressive personality traits, aggressive alcohol expectancies, aggressogenic physical and social bar environments, and total number of drinks. Results of this study suggest that in alcohol-related bar conflicts, higher levels of young adult AmED use are associated with higher levels of aggression perpetration than alcohol use alone and that the elevated risk is not attributable to individual differences between AmED users and nonusers or to contextual differences in bar drinking settings. While future research is needed to identify motivations, dosages, and sequencing issues associated with AmED use, these beverages should be considered a potential risk factor in the escalation of aggressive bar conflicts. Copyright © 2016 by the Research Society on Alcoholism.

Comparison of the passivity between cast alloy and laser-welded titanium overdenture bars.

PubMed

Paiva, Jose; Givan, Daniel A; Broome, James C; Lemons, Jack E; McCracken, Michael S

2009-12-01

The purpose of this study was to investigate the fit of cast alloy overdenture and laser-welded titanium-alloy bars by measuring induced strain upon tightening of the bars on a master cast as well as a function of screw tightening sequence. Four implant analogs were secured into Type IV dental stone to simulate a mandibular edentulous patient cast, and two groups of four overdenture bars were fabricated. Group I was four cast alloy bars and Group II was four laser-welded titanium bars. The cast alloy bars included Au-Ag-Pd, Pd-Ag-Au, Au-Ag-Cu-Pd, and Ag-Pd-Cu-Au, while the laser-welded bars were all Ti-Al-V alloy. Bars were made from the same master cast, were torqued into place, and the total strain in the bars was measured through five strain gauges bonded to the bar between the implants. Each bar was placed and torqued 27 times to 30 Ncm per screw using three tightening sequences. Data were processed through a strain amplifier and analyzed by computer using StrainSmart software. Data were analyzed by ANOVA and Tukey's post hoc test. Significant differences were found between alloy types. Laser-welded titanium bars tended to have lower strains than corresponding cast bars, although the Au-Ag-Pd bar was not significantly different. The magnitudes of total strain were the least when first tightening the ends of the bar. The passivity of implant overdenture bars was evaluated using total strain of the bar when tightening. Selecting a high modulus of elasticity cast alloy or use of laser-welded bar design resulted in the lowest average strain magnitudes. While the effect of screw tightening sequence was minimal, tightening the distal ends first demonstrated the lowest strain, and hence the best passivity.

Studies on solid solutions based on layered honeycomb-ordered phases P2-Na{sub 2}M{sub 2}TeO{sub 6} (M=Co, Ni, Zn)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berthelot, Romain; Schmidt, Whitney; Sleight, A.W.

2012-12-15

Three complete solid solutions between the layered phases P2-Na{sub 2}M{sub 2}TeO{sub 6} (M=Co, Ni, Zn) have been prepared by conventional solid state method and investigated through X-ray diffraction, magnetism and optical measurements. All compositions are characterized by a M{sup 2+}/X{sup 6+} honeycomb ordering within the slabs and crystallize in a hexagonal unit cell. However, a structural transition based on a different stacking is observed as nickel (space group P6{sub 3}/mcm) is substituted by zinc or cobalt (space group P6{sub 3}22). All compositions exhibit a paramagnetic Curie-Weiss behavior at high temperatures; and the magnetic moment values confirm the presence of Ni{supmore » 2+} and/or Co{sup 2+} cations. The low-temperature antiferromagnetic order of Na{sub 2}Ni{sub 2}TeO{sub 6} and Na{sub 2}Co{sub 2}TeO{sub 6} is suppressed by zinc substitution. The color of the obtained compositions varies from pink, to light green and white when M=Co, Ni, Zn, respectively. - Graphical abstract: The comparison between the structure of Na{sub 2}Ni{sub 2}TeO{sub 6} (left) and Na{sub 2}M{sub 2}TeO{sub 6} (M=Co, Zn) (right) evidences the stacking difference with distinct atom sequences along the hexagonal c-axis. Highlights: Black-Right-Pointing-Pointer Solid solutions between lamellar phases Na{sub 2}M{sub 2}TeO{sub 6} (M=Co, Ni, Zn) are investigated. Black-Right-Pointing-Pointer A M{sup 2+}/X{sup 6+} honeycomb ordering characterized all the compositions. Black-Right-Pointing-Pointer A structural transition is shown when Ni is replaced by Co or Zn. Black-Right-Pointing-Pointer The low-temperature AFM ordering of Na{sub 2}Ni{sub 2}TeO{sub 6} and Na{sub 2}Co{sub 2}TeO{sub 6} is suppressed by zinc substitution. Black-Right-Pointing-Pointer Color changes from pink to light green and white when M=Co, Ni, Zn, respectively.« less

Endophilin-A1 BAR domain interaction with arachidonyl CoA.

PubMed

Petoukhov, Maxim V; Weissenhorn, Winfried; Svergun, Dmitri I

2014-01-01

Endophilin-A1 belongs to the family of BAR domain containing proteins that catalyze membrane remodeling processes via sensing, inducing and stabilizing membrane curvature. We show that the BAR domain of endophilin-A1 binds arachidonic acid and molds its coenzyme A (CoA) activated form, arachidonyl-CoA into a defined structure. We studied low resolution structures of endophilin-A1-BAR and its complex with arachidonyl-CoA in solution using synchrotron small-angle X-ray scattering (SAXS). The free endophilin-A1-BAR domain is shown to be dimeric at lower concentrations but builds tetramers and higher order complexes with increasing concentrations. Extensive titration SAXS studies revealed that the BAR domain produces a homogenous complex with the lipid micelles. The structural model of the complexes revealed two arachidonyl-CoA micelles bound to the distal arms of an endophilin-A1-BAR dimer. Intriguingly, the radius of the bound micelles significantly decreases compared to that of the free micelles, and this structural result may provide hints on the potential biological relevance of the endophilin-A1-BAR interaction with arachidonyl CoA.

Electronic Structure and Multisite Basicity of the Pyramidal Phosphinidene-Bridged Dimolybdenum Complex [Mo2(η(5)-C5H5)(μ-κ(1):κ(1),η(5)-PC5H4)(η(6)-C6H3(t)Bu3)(CO)2(PMe3)].

PubMed

Albuerne, Isabel G; Alvarez, M Angeles; García, M Esther; García-Vivó, Daniel; Ruiz, Miguel A

2015-10-19

The title phosphinidene complex could be sequentially protonated with HBF4·OEt2 or [H(OEt2)2](BAr'4) to give the phosphido-bridged derivatives [Mo2Cp(μ-κ(1):κ(1),η(5)-HPC5H4)(η(6)-HMes*)(CO)2(PMe3)]X and then the hydrides [Mo2Cp(H)(μ-κ(1):κ(1),η(5)-HPC5H4)(η(6)-HMes*)(CO)2(PMe3)]X2 (X = BF4, BAr'4; Ar' = 3,5-C6H3(CF3)2; Mes* = 2,4,6-C6H2(t)Bu3). Density functional theory (DFT) calculations revealed that the most favored site for initial electrophilic attack is the metallocene Mo atom, but attachment of the electrophile to the phosphinidene P atom gives more stable products. This was in agreement with all other reactions investigated, which invariably involved the attachment of the added electrophile at the P site. Thus, the title compound reacted with S8 at 223 K to give the thiophosphinidene-bridged complex [Mo2Cp{μ-κ(1):κ(1),η(5)-P(S)C5H4}(η(6)-HMes*)(CO)2(PMe3)], a poorly stable molecule which reacted with MeI at room temperature to give the corresponding thiolatophosphido derivative, isolated as [Mo2Cp{μ-κ(1):κ(1),η(5)-P(SMe)C5H4}(η(6)-HMes*)(CO)2(PMe3)](BAr'4) (P-S = 2.128(4) Å) after anion exchange with Na(BAr'4). Reaction of the title compound with MeI proceeded smoothly to give the corresponding methylphosphido derivative, isolated analogously as [Mo2Cp{μ-κ(1):κ(1),η(5)-P(Me)C5H4}(η(6)-HMes*)(CO)2(PMe3)](BAr'4). The related complex [Mo2Cp{μ-κ(1):κ(1),η(5)-P(Me)C5H4}(η(6)-HMes*)(CO)2(PMe2Ph)](BAr'4) (P-C(Me) = 1.841(5) Å) could be prepared analogously from the neutral precursor [Mo2Cp{μ-κ(1):κ(1),η(5)-PC5H4}(η(6)-HMes*)(CO)2(PMe2Ph)]. In contrast, reaction of the title complex with ethylene sulfide involved opening of the C2S ring and formation of new P-C and Mo-S bonds (1.886(7) and 2.493(2) Å, respectively), with displacement of the PMe3 ligand, to give the phosphido-thiolato complex [Mo2Cp{μ-κ(2)(P,S):κ(1)P,η(5)-P(C2H4S)C5H4}(η(6)-HMes*)(CO)2]. All these derivatives of the title complex displayed an unusual

Mass modeling for bars

NASA Technical Reports Server (NTRS)

Butler, Thomas G.

1987-01-01

Methods of modeling mass for bars are surveyed. A method for extending John Archer's concept of consistent mass beyond just translational inertia effects is included. Recommendations are given for various types of modeling situations.

Generation of gas-phase sodiated arenes such as [(Na3(C6H4)+] from benzene dicarboxylate salts.

PubMed

Attygalle, Athula B; Chan, Chang-Ching; Axe, Frank U; Bolgar, Mark

2010-01-01

Upon collision-induced activation, gaseous sodium adducts generated by electrospray ionization of disodium salts of 1,2- 1,3-, and 1,4-benzene dicarboxylic acids (m/z 233) undergo an unprecedented expulsion of CO(2) by a rearrangement process to produce an ion of m/z 189 in which all three sodium atoms are retained. When isolated in a collision cell of a tandem-in-space mass spectrometer, and subjected to collision-induced dissociation (CID), only the m/z 189 ions derived from the meta and para isomers underwent a further CO(2) loss to produce a peak at m/z 145 for a sodiated arene of formula (Na(3)C(6)H(4))(+). This previously unreported m/z 145 ion, which is useful to differentiate meta and para benzene dicarboxylates from their ortho isomer, is in fact the sodium adduct of phenelenedisodium. Moreover, the m/z 189 ion from all three isomers readily expelled a sodium radical to produce a peak at m/z 166 for a radical cation [(*C(6)H(4)CO(2)Na(2))(+)], which then eliminated CO(2) to produce a peak at m/z 122 for the distonic cation (*C(6)H(4)Na(2))(+). Copyright 2009 John Wiley & Sons, Ltd.

Genderedness of bar drinking culture and alcohol-related harms: A multi-country study

PubMed Central

Roberts, Sarah C. M.; Bond, Jason; Korcha, Rachael; Greenfield, Thomas K.

2012-01-01

This study explores whether associations between consuming alcohol in bars and alcohol-related harms are consistent across countries and whether country-level characteristics modify associations. We hypothesized that genderedness of bar drinking modifies associations, such that odds of harms associated with bar drinking increase more rapidly in predominantly male bar-drinking countries. Multilevel analysis was used to analyze survey data from 21 countries representing five continents from Gender, Alcohol, and Culture: An International Study (GENACIS). Bar frequency was positively associated with harms overall. Relationships between bar frequency and harms varied across country. Genderedness modified associations between bar frequency and odds of fights, marriage/relationship harms, and work harms. Findings were significant only for men. Contrary to our hypothesis, odds of harms associated with bar drinking increased less rapidly in countries where bar drinking is predominantly male. This suggests predominantly male bar drinking cultures may be protective for males who more frequently drink in bars. PMID:23710158

On the existence of a high-temperature polymorph of Na2Ca6Si4O15—implications for the phase equilibria in the system Na2O-CaO-SiO2

NASA Astrophysics Data System (ADS)

Kahlenberg, Volker; Maier, Matthias

2016-12-01

Singe crystals of a new high-temperature polymorph of Na2Ca6Si4O15 have been obtained from solid state reactions performed at 1300 °C. The basic crystallographic data of this so-called β-phase at ambient conditions are as follows: space group P1 c1, a = 9.0112(5) Å, b = 7.3171(5) Å, c = 10.9723(6) Å, β = 107.720(14)°, V = 689.14(7) Å3, Z = 2. The crystals showed twinning by reticular merohedry (mimicking an orthorhombic C-centred unit cell) which was accounted for during data processing and structure solution. Structure determination was accomplished by direct methods. Least-squares refinements resulted in a residual of R(|F|) = 0.043 for 5811 observed reflections with I > 2σ(I). From a structural point of view β-Na2Ca6Si4O15 can be attributed to the group of mixed-anion silicates containing [Si2O7]-dimers as well as isolated [SiO4]-tetrahedra in the ratio 1:2, i.e. more precisely the formula can be written as Na2Ca6[SiO4]2[Si2O7]. The tetrahedral groups are arranged in layers parallel to (100). Sodium and calcium cations are located between the silicate anions for charge compensation and are coordinated by six to eight nearest oxygen ligands. Alternatively, the structure can be described as a mixed tetrahedral-octahedral framework based on kröhnkite-type [Ca(SiO4)2O2]-chains in which the CaO6-octahedra are corner-linked to bridging SiO4-tetrahedra. The infinite chains are running parallel to [001] and are concentrated in layers parallel to (010). Adjacent layers are shifted relative to each other by an amount of +δ or -δ along a*. Consequently, a …ABABAB… stacking sequence is created. A detailed comparison with related structures such as α-Na2Ca6Si4O15 and other A2B6Si4O15 representatives including topological as well as group theoretical aspects is presented. There are strong indications that monoclinic Na2Ca3Si2O8 mentioned in earlier studies is actually misinterpreted β-Na2Ca6Si4O15. In addition to the detailed crystallographic analysis of

Synthesis, crystal structure and spectroscopy properties of Na 3AZr(PO 4) 3 ( A=Mg, Ni) and Li 2.6Na 0.4NiZr(PO 4) 3 phosphates

NASA Astrophysics Data System (ADS)

Chakir, M.; El Jazouli, A.; de Waal, D.

2006-06-01

Na 3AZr(PO 4) 3 ( A=Mg, Ni) phosphates were prepared at 750 °C by coprecipitation route. Their crystal structures have been refined at room temperature from X-ray powder diffraction data using Rietveld method. Li 2.6Na 0.4NiZr(PO 4) 3 was synthesized through ion exchange from the sodium analog. These materials belong to the Nasicon-type structure. Raman spectra of Na 3AZr(PO 4) 3 ( A=Mg, Ni) phosphates present broad peaks in favor of the statistical distribution in the sites around PO 4 tetrahedra. Diffuse reflectance spectra indicate the presence of octahedrally coordinated Ni 2+ ions.

Measurements of t t bar cross sections in association with b jets and inclusive jets and their ratio using dilepton final states in pp collisions at √{ s } = 13TeV

NASA Astrophysics Data System (ADS)

Sirunyan, A. M.; Tumasyan, A.; Adam, W.; Asilar, E.; Bergauer, T.; Brandstetter, J.; Brondolin, E.; Dragicevic, M.; Erö, J.; Flechl, M.; Friedl, M.; Frühwirth, R.; Ghete, V. M.; Hörmann, N.; Hrubec, J.; Jeitler, M.; König, A.; Krätschmer, I.; Liko, D.; Matsushita, T.; Mikulec, I.; Rabady, D.; Rad, N.; Rohringer, H.; Schieck, J.; Strauss, J.; Waltenberger, W.; Wulz, C.-E.; Chekhovsky, V.; Mossolov, V.; Suarez Gonzalez, J.; Shumeiko, N.; Alderweireldt, S.; De Wolf, E. A.; Janssen, X.; Lauwers, J.; Van De Klundert, M.; Van Haevermaet, H.; Van Mechelen, P.; Van Remortel, N.; Van Spilbeeck, A.; Abu Zeid, S.; Blekman, F.; D'Hondt, J.; De Bruyn, I.; De Clercq, J.; Deroover, K.; Lowette, S.; Moortgat, S.; Moreels, L.; Olbrechts, A.; Python, Q.; Skovpen, K.; Tavernier, S.; Van Doninck, W.; Van Mulders, P.; Van Parijs, I.; Brun, H.; Clerbaux, B.; De Lentdecker, G.; Delannoy, H.; Fasanella, G.; Favart, L.; Goldouzian, R.; Grebenyuk, A.; Karapostoli, G.; Lenzi, T.; Luetic, J.; Maerschalk, T.; Marinov, A.; Randle-conde, A.; Seva, T.; Vander Velde, C.; Vanlaer, P.; Vannerom, D.; Yonamine, R.; Zenoni, F.; Zhang, F.; Cimmino, A.; Cornelis, T.; Dobur, D.; Fagot, A.; Gul, M.; Khvastunov, I.; Poyraz, D.; Salva, S.; Schöfbeck, R.; Tytgat, M.; Van Driessche, W.; Verbeke, W.; Zaganidis, N.; Bakhshiansohi, H.; Bondu, O.; Brochet, S.; Bruno, G.; Caudron, A.; De Visscher, S.; Delaere, C.; Delcourt, M.; Francois, B.; Giammanco, A.; Jafari, A.; Komm, M.; Krintiras, G.; Lemaitre, V.; Magitteri, A.; Mertens, A.; Musich, M.; Piotrzkowski, K.; Quertenmont, L.; Vidal Marono, M.; Wertz, S.; Beliy, N.; Aldá Júnior, W. L.; Alves, F. L.; Alves, G. A.; Brito, L.; Hensel, C.; Moraes, A.; Pol, M. E.; Rebello Teles, P.; Belchior Batista Das Chagas, E.; Carvalho, W.; Chinellato, J.; Custódio, A.; Da Costa, E. M.; Da Silveira, G. G.; De Jesus Damiao, D.; Fonseca De Souza, S.; Huertas Guativa, L. M.; Malbouisson, H.; Mora Herrera, C.; Mundim, L.; Nogima, H.; Santoro, A.; Sznajder, A.; Tonelli Manganote, E. J.; Torres Da Silva De Araujo, F.; Vilela Pereira, A.; Ahuja, S.; Bernardes, C. A.; Fernandez Perez Tomei, T. R.; Gregores, E. M.; Mercadante, P. G.; Moon, C. S.; Novaes, S. F.; Padula, Sandra S.; Romero Abad, D.; Ruiz Vargas, J. C.; Aleksandrov, A.; Hadjiiska, R.; Iaydjiev, P.; Rodozov, M.; Stoykova, S.; Sultanov, G.; Vutova, M.; Dimitrov, A.; Glushkov, I.; Litov, L.; Pavlov, B.; Petkov, P.; Fang, W.; Gao, X.; Ahmad, M.; Bian, J. G.; Chen, G. M.; Chen, H. S.; Chen, M.; Chen, Y.; Jiang, C. H.; Leggat, D.; Liu, Z.; Romeo, F.; Shaheen, S. M.; Spiezia, A.; Tao, J.; Wang, C.; Wang, Z.; Yazgan, E.; Zhang, H.; Zhao, J.; Ban, Y.; Chen, G.; Li, Q.; Liu, S.; Mao, Y.; Qian, S. J.; Wang, D.; Xu, Z.; Avila, C.; Cabrera, A.; Chaparro Sierra, L. F.; Florez, C.; González Hernández, C. F.; Ruiz Alvarez, J. D.; Godinovic, N.; Lelas, D.; Puljak, I.; Ribeiro Cipriano, P. M.; Sculac, T.; Antunovic, Z.; Kovac, M.; Brigljevic, V.; Ferencek, D.; Kadija, K.; Mesic, B.; Susa, T.; Ather, M. W.; Attikis, A.; Mavromanolakis, G.; Mousa, J.; Nicolaou, C.; Ptochos, F.; Razis, P. A.; Rykaczewski, H.; Finger, M.; Finger, M.; Carrera Jarrin, E.; Abdelalim, A. A.; Mohammed, Y.; Salama, E.; Dewanjee, R. K.; Kadastik, M.; Perrini, L.; Raidal, M.; Tiko, A.; Veelken, C.; Eerola, P.; Pekkanen, J.; Voutilainen, M.; Härkönen, J.; Järvinen, T.; Karimäki, V.; Kinnunen, R.; Lampén, T.; Lassila-Perini, K.; Lehti, S.; Lindén, T.; Luukka, P.; Tuominen, E.; Tuominiemi, J.; Tuovinen, E.; Talvitie, J.; Tuuva, T.; Besancon, M.; Couderc, F.; Dejardin, M.; Denegri, D.; Faure, J. L.; Ferri, F.; Ganjour, S.; Ghosh, S.; Givernaud, A.; Gras, P.; Hamel de Monchenault, G.; Jarry, P.; Kucher, I.; Locci, E.; Machet, M.; Malcles, J.; Rander, J.; Rosowsky, A.; Sahin, M. Ö.; Titov, M.; Abdulsalam, A.; Antropov, I.; Baffioni, S.; Beaudette, F.; Busson, P.; Cadamuro, L.; Chapon, E.; Charlot, C.; Davignon, O.; Granier de Cassagnac, R.; Jo, M.; Lisniak, S.; Lobanov, A.; Miné, P.; Nguyen, M.; Ochando, C.; Ortona, G.; Paganini, P.; Pigard, P.; Regnard, S.; Salerno, R.; Sirois, Y.; Stahl Leiton, A. G.; Strebler, T.; Yilmaz, Y.; Zabi, A.; Zghiche, A.; Agram, J.-L.; Andrea, J.; Bloch, D.; Brom, J.-M.; Buttignol, M.; Chabert, E. C.; Chanon, N.; Collard, C.; Conte, E.; Coubez, X.; Fontaine, J.-C.; Gelé, D.; Goerlach, U.; Le Bihan, A.-C.; Van Hove, P.; Gadrat, S.; Beauceron, S.; Bernet, C.; Boudoul, G.; Chierici, R.; Contardo, D.; Courbon, B.; Depasse, P.; El Mamouni, H.; Fay, J.; Finco, L.; Gascon, S.; Gouzevitch, M.; Grenier, G.; Ille, B.; Lagarde, F.; Laktineh, I. B.; Lethuillier, M.; Mirabito, L.; Pequegnot, A. L.; Perries, S.; Popov, A.; Sordini, V.; Vander Donckt, M.; Viret, S.; Toriashvili, T.; Lomidze, D.; Autermann, C.; Beranek, S.; Feld, L.; Kiesel, M. K.; Klein, K.; Lipinski, M.; Preuten, M.; Schomakers, C.; Schulz, J.; Verlage, T.; Albert, A.; Brodski, M.; Dietz-Laursonn, E.; Duchardt, D.; Endres, M.; Erdmann, M.; Erdweg, S.; Esch, T.; Fischer, R.; Güth, A.; Hamer, M.; Hebbeker, T.; Heidemann, C.; Hoepfner, K.; Knutzen, S.; Merschmeyer, M.; Meyer, A.; Millet, P.; Mukherjee, S.; Olschewski, M.; Padeken, K.; Pook, T.; Radziej, M.; Reithler, H.; Rieger, M.; Scheuch, F.; Sonnenschein, L.; Teyssier, D.; Thüer, S.; Flügge, G.; Kargoll, B.; Kress, T.; Künsken, A.; Lingemann, J.; Müller, T.; Nehrkorn, A.; Nowack, A.; Pistone, C.; Pooth, O.; Stahl, A.; Aldaya Martin, M.; Arndt, T.; Asawatangtrakuldee, C.; Beernaert, K.; Behnke, O.; Behrens, U.; Bin Anuar, A. A.; Borras, K.; Botta, V.; Campbell, A.; Connor, P.; Contreras-Campana, C.; Costanza, F.; Diez Pardos, C.; Eckerlin, G.; Eckstein, D.; Eichhorn, T.; Eren, E.; Gallo, E.; Garay Garcia, J.; Geiser, A.; Gizhko, A.; Grados Luyando, J. M.; Grohsjean, A.; Gunnellini, P.; Harb, A.; Hauk, J.; Hempel, M.; Jung, H.; Kalogeropoulos, A.; Kasemann, M.; Keaveney, J.; Kleinwort, C.; Korol, I.; Krücker, D.; Lange, W.; Lelek, A.; Lenz, T.; Leonard, J.; Lipka, K.; Lohmann, W.; Mankel, R.; Melzer-Pellmann, I.-A.; Meyer, A. B.; Mittag, G.; Mnich, J.; Mussgiller, A.; Ntomari, E.; Pitzl, D.; Placakyte, R.; Raspereza, A.; Roland, B.; Savitskyi, M.; Saxena, P.; Shevchenko, R.; Spannagel, S.; Stefaniuk, N.; Van Onsem, G. P.; Walsh, R.; Wen, Y.; Wichmann, K.; Wissing, C.; Bein, S.; Blobel, V.; Centis Vignali, M.; Draeger, A. R.; Dreyer, T.; Garutti, E.; Gonzalez, D.; Haller, J.; Hoffmann, M.; Junkes, A.; Klanner, R.; Kogler, R.; Kovalchuk, N.; Kurz, S.; Lapsien, T.; Marchesini, I.; Marconi, D.; Meyer, M.; Niedziela, M.; Nowatschin, D.; Pantaleo, F.; Peiffer, T.; Perieanu, A.; Scharf, C.; Schleper, P.; Schmidt, A.; Schumann, S.; Schwandt, J.; Sonneveld, J.; Stadie, H.; Steinbrück, G.; Stober, F. M.; Stöver, M.; Tholen, H.; Troendle, D.; Usai, E.; Vanelderen, L.; Vanhoefer, A.; Vormwald, B.; Akbiyik, M.; Barth, C.; Baur, S.; Baus, C.; Berger, J.; Butz, E.; Caspart, R.; Chwalek, T.; Colombo, F.; De Boer, W.; Dierlamm, A.; Freund, B.; Friese, R.; Giffels, M.; Gilbert, A.; Haitz, D.; Hartmann, F.; Heindl, S. M.; Husemann, U.; Kassel, F.; Kudella, S.; Mildner, H.; Mozer, M. U.; Müller, Th.; Plagge, M.; Quast, G.; Rabbertz, K.; Schröder, M.; Shvetsov, I.; Sieber, G.; Simonis, H. J.; Ulrich, R.; Wayand, S.; Weber, M.; Weiler, T.; Williamson, S.; Wöhrmann, C.; Wolf, R.; Anagnostou, G.; Daskalakis, G.; Geralis, T.; Giakoumopoulou, V. A.; Kyriakis, A.; Loukas, D.; Topsis-Giotis, I.; Kesisoglou, S.; Panagiotou, A.; Saoulidou, N.; Evangelou, I.; Flouris, G.; Foudas, C.; Kokkas, P.; Manthos, N.; Papadopoulos, I.; Paradas, E.; Strologas, J.; Triantis, F. A.; Csanad, M.; Filipovic, N.; Pasztor, G.; Bencze, G.; Hajdu, C.; Horvath, D.; Sikler, F.; Veszpremi, V.; Vesztergombi, G.; Zsigmond, A. J.; Beni, N.; Czellar, S.; Karancsi, J.; Makovec, A.; Molnar, J.; Szillasi, Z.; Bartók, M.; Raics, P.; Trocsanyi, Z. L.; Ujvari, B.; Choudhury, S.; Komaragiri, J. R.; Bahinipati, S.; Bhowmik, S.; Mal, P.; Mandal, K.; Nayak, A.; Sahoo, D. K.; Sahoo, N.; Swain, S. K.; Bansal, S.; Beri, S. B.; Bhatnagar, V.; Bhawandeep, U.; Chawla, R.; Dhingra, N.; Kalsi, A. K.; Kaur, A.; Kaur, M.; Kumar, R.; Kumari, P.; Mehta, A.; Mittal, M.; Singh, J. B.; Walia, G.; Kumar, Ashok; Shah, Aashaq; Bhardwaj, A.; Chauhan, S.; Choudhary, B. C.; Garg, R. B.; Keshri, S.; Malhotra, S.; Naimuddin, M.; Ranjan, K.; Sharma, R.; Sharma, V.; Bhattacharya, R.; Bhattacharya, S.; Dey, S.; Dutt, S.; Dutta, S.; Ghosh, S.; Majumdar, N.; Modak, A.; Mondal, K.; Mukhopadhyay, S.; Nandan, S.; Purohit, A.; Roy, A.; Roy, D.; Roy Chowdhury, S.; Sarkar, S.; Sharan, M.; Thakur, S.; Behera, P. K.; Chudasama, R.; Dutta, D.; Jha, V.; Kumar, V.; Mohanty, A. K.; Netrakanti, P. K.; Pant, L. M.; Shukla, P.; Topkar, A.; Aziz, T.; Dugad, S.; Mahakud, B.; Mitra, S.; Mohanty, G. B.; Parida, B.; Sur, N.; Sutar, B.; Banerjee, S.; Bhattacharya, S.; Chatterjee, S.; Das, P.; Guchait, M.; Jain, Sa.; Kumar, S.; Maity, M.; Majumder, G.; Mazumdar, K.; Sarkar, T.; Wickramage, N.; Chauhan, S.; Dube, S.; Hegde, V.; Kapoor, A.; Kothekar, K.; Pandey, S.; Rane, A.; Sharma, S.; Chenarani, S.; Eskandari Tadavani, E.; Etesami, S. M.; Khakzad, M.; Mohammadi Najafabadi, M.; Naseri, M.; Paktinat Mehdiabadi, S.; Rezaei Hosseinabadi, F.; Safarzadeh, B.; Zeinali, M.; Felcini, M.; Grunewald, M.; Abbrescia, M.; Calabria, C.; Caputo, C.; Colaleo, A.; Creanza, D.; Cristella, L.; De Filippis, N.; De Palma, M.; Fiore, L.; Iaselli, G.; Maggi, G.; Maggi, M.; Miniello, G.; My, S.; Nuzzo, S.; Pompili, A.; Pugliese, G.; Radogna, R.; Ranieri, A.; Selvaggi, G.; Sharma, A.; Silvestris, L.; Venditti, R.; Verwilligen, P.; Abbiendi, G.; Battilana, C.; Bonacorsi, D.; Braibant-Giacomelli, S.; Brigliadori, L.; Campanini, R.; Capiluppi, P.; Castro, A.; Cavallo, F. R.; Chhibra, S. S.; Cuffiani, M.; Dallavalle, G. M.; Fabbri, F.; Fanfani, A.; Fasanella, D.; Giacomelli, P.; Guiducci, L.; Marcellini, S.; Masetti, G.; Navarria, F. L.; Perrotta, A.; Rossi, A. M.; Rovelli, T.; Siroli, G. P.; Tosi, N.; Albergo, S.; Costa, S.; Di Mattia, A.; Giordano, F.; Potenza, R.; Tricomi, A.; Tuve, C.; Barbagli, G.; Chatterjee, K.; Ciulli, V.; Civinini, C.; D'Alessandro, R.; Focardi, E.; Lenzi, P.; Meschini, M.; Paoletti, S.; Russo, L.; Sguazzoni, G.; Strom, D.; Viliani, L.; Benussi, L.; Bianco, S.; Fabbri, F.; Piccolo, D.; Primavera, F.; Calvelli, V.; Ferro, F.; Robutti, E.; Tosi, S.; Brianza, L.; Brivio, F.; Ciriolo, V.; Dinardo, M. E.; Fiorendi, S.; Gennai, S.; Ghezzi, A.; Govoni, P.; Malberti, M.; Malvezzi, S.; Manzoni, R. A.; Menasce, D.; Moroni, L.; Paganoni, M.; Pauwels, K.; Pedrini, D.; Pigazzini, S.; Ragazzi, S.; Tabarelli de Fatis, T.; Buontempo, S.; Cavallo, N.; Di Guida, S.; Esposito, M.; Fabozzi, F.; Fienga, F.; Iorio, A. O. M.; Khan, W. A.; Lanza, G.; Lista, L.; Meola, S.; Paolucci, P.; Sciacca, C.; Thyssen, F.; Azzi, P.; Bacchetta, N.; Benato, L.; Boletti, A.; Carlin, R.; Carvalho Antunes De Oliveira, A.; Checchia, P.; Dall'Osso, M.; De Castro Manzano, P.; Dorigo, T.; Gasparini, U.; Gozzelino, A.; Lacaprara, S.; Margoni, M.; Meneguzzo, A. T.; Michelotto, M.; Montecassiano, F.; Passaseo, M.; Pozzobon, N.; Ronchese, P.; Rossin, R.; Simonetto, F.; Torassa, E.; Zanetti, M.; Zotto, P.; Zumerle, G.; Braghieri, A.; Fallavollita, F.; Magnani, A.; Montagna, P.; Ratti, S. P.; Re, V.; Ressegotti, M.; Riccardi, C.; Salvini, P.; Vai, I.; Vitulo, P.; Alunni Solestizi, L.; Bilei, G. M.; Ciangottini, D.; Fanò, L.; Lariccia, P.; Leonardi, R.; Mantovani, G.; Mariani, V.; Menichelli, M.; Saha, A.; Santocchia, A.; Spiga, D.; Androsov, K.; Azzurri, P.; Bagliesi, G.; Bernardini, J.; Boccali, T.; Borrello, L.; Castaldi, R.; Ciocci, M. A.; Dell'Orso, R.; Fedi, G.; Giassi, A.; Grippo, M. T.; Ligabue, F.; Lomtadze, T.; Martini, L.; Messineo, A.; Palla, F.; Rizzi, A.; Savoy-Navarro, A.; Spagnolo, P.; Tenchini, R.; Tonelli, G.; Venturi, A.; Verdini, P. G.; Barone, L.; Cavallari, F.; Cipriani, M.; Del Re, D.; Diemoz, M.; Gelli, S.; Longo, E.; Margaroli, F.; Marzocchi, B.; Meridiani, P.; Organtini, G.; Paramatti, R.; Preiato, F.; Rahatlou, S.; Rovelli, C.; Santanastasio, F.; Amapane, N.; Arcidiacono, R.; Argiro, S.; Arneodo, M.; Bartosik, N.; Bellan, R.; Biino, C.; Cartiglia, N.; Cenna, F.; Costa, M.; Covarelli, R.; Degano, A.; Demaria, N.; Kiani, B.; Mariotti, C.; Maselli, S.; Migliore, E.; Monaco, V.; Monteil, E.; Monteno, M.; Obertino, M. M.; Pacher, L.; Pastrone, N.; Pelliccioni, M.; Pinna Angioni, G. L.; Ravera, F.; Romero, A.; Ruspa, M.; Sacchi, R.; Shchelina, K.; Sola, V.; Solano, A.; Staiano, A.; Traczyk, P.; Belforte, S.; Casarsa, M.; Cossutti, F.; Della Ricca, G.; Zanetti, A.; Kim, D. H.; Kim, G. N.; Kim, M. S.; Lee, J.; Lee, S.; Lee, S. W.; Oh, Y. D.; Sekmen, S.; Son, D. C.; Yang, Y. C.; Lee, A.; Kim, H.; Moon, D. H.; Brochero Cifuentes, J. A.; Goh, J.; Kim, T. J.; Cho, S.; Choi, S.; Go, Y.; Gyun, D.; Ha, S.; Hong, B.; Jo, Y.; Kim, Y.; Lee, K.; Lee, K. S.; Lee, S.; Lim, J.; Park, S. K.; Roh, Y.; Almond, J.; Kim, J.; Lee, H.; Oh, S. B.; Radburn-Smith, B. C.; Seo, S. h.; Yang, U. K.; Yoo, H. D.; Yu, G. B.; Choi, M.; Kim, H.; Kim, J. H.; Lee, J. S. H.; Park, I. C.; Ryu, G.; Choi, Y.; Hwang, C.; Lee, J.; Yu, I.; Dudenas, V.; Juodagalvis, A.; Vaitkus, J.; Ahmed, I.; Ibrahim, Z. A.; Md Ali, M. A. B.; Mohamad Idris, F.; Wan Abdullah, W. A. T.; Yusli, M. N.; Zolkapli, Z.; Castilla-Valdez, H.; De La Cruz-Burelo, E.; Heredia-De La Cruz, I.; Lopez-Fernandez, R.; Mejia Guisao, J.; Sanchez-Hernandez, A.; Carrillo Moreno, S.; Oropeza Barrera, C.; Vazquez Valencia, F.; Pedraza, I.; Salazar Ibarguen, H. A.; Uribe Estrada, C.; Morelos Pineda, A.; Krofcheck, D.; Butler, P. H.; Ahmad, A.; Ahmad, M.; Hassan, Q.; Hoorani, H. R.; Saddique, A.; Shah, M. A.; Shoaib, M.; Waqas, M.; Bialkowska, H.; Bluj, M.; Boimska, B.; Frueboes, T.; Górski, M.; Kazana, M.; Nawrocki, K.; Romanowska-Rybinska, K.; Szleper, M.; Zalewski, P.; Bunkowski, K.; Byszuk, A.; Doroba, K.; Kalinowski, A.; Konecki, M.; Krolikowski, J.; Misiura, M.; Olszewski, M.; Pyskir, A.; Walczak, M.; Bargassa, P.; Beirão Da Cruz E Silva, C.; Calpas, B.; Di Francesco, A.; Faccioli, P.; Gallinaro, M.; Hollar, J.; Leonardo, N.; Lloret Iglesias, L.; Nemallapudi, M. V.; Seixas, J.; Toldaiev, O.; Vadruccio, D.; Varela, J.; Afanasiev, S.; Bunin, P.; Gavrilenko, M.; Golutvin, I.; Gorbunov, I.; Kamenev, A.; Karjavin, V.; Lanev, A.; Malakhov, A.; Matveev, V.; Palichik, V.; Perelygin, V.; Shmatov, S.; Shulha, S.; Skatchkov, N.; Smirnov, V.; Voytishin, N.; Zarubin, A.; Ivanov, Y.; Kim, V.; Kuznetsova, E.; Levchenko, P.; Murzin, V.; Oreshkin, V.; Smirnov, I.; Sulimov, V.; Uvarov, L.; Vavilov, S.; Vorobyev, A.; Andreev, Yu.; Dermenev, A.; Gninenko, S.; Golubev, N.; Karneyeu, A.; Kirsanov, M.; Krasnikov, N.; Pashenkov, A.; Tlisov, D.; Toropin, A.; Epshteyn, V.; Gavrilov, V.; Lychkovskaya, N.; Popov, V.; Pozdnyakov, I.; Safronov, G.; Spiridonov, A.; Toms, M.; Vlasov, E.; Zhokin, A.; Aushev, T.; Bylinkin, A.; Chadeeva, M.; Polikarpov, S.; Rusinov, V.; Andreev, V.; Azarkin, M.; Dremin, I.; Kirakosyan, M.; Terkulov, A.; Baskakov, A.; Belyaev, A.; Boos, E.; Bunichev, V.; Dubinin, M.; Dudko, L.; Klyukhin, V.; Kodolova, O.; Korneeva, N.; Lokhtin, I.; Miagkov, I.; Obraztsov, S.; Perfilov, M.; Savrin, V.; Volkov, P.; Blinov, V.; Skovpen, Y.; Shtol, D.; Azhgirey, I.; Bayshev, I.; Bitioukov, S.; Elumakhov, D.; Kachanov, V.; Kalinin, A.; Konstantinov, D.; Krychkine, V.; Petrov, V.; Ryutin, R.; Sobol, A.; Troshin, S.; Tyurin, N.; Uzunian, A.; Volkov, A.; Adzic, P.; Cirkovic, P.; Devetak, D.; Dordevic, M.; Milosevic, J.; Rekovic, V.; Alcaraz Maestre, J.; Barrio Luna, M.; Cerrada, M.; Colino, N.; De La Cruz, B.; Delgado Peris, A.; Escalante Del Valle, A.; Fernandez Bedoya, C.; Fernández Ramos, J. P.; Flix, J.; Fouz, M. C.; Garcia-Abia, P.; Gonzalez Lopez, O.; Goy Lopez, S.; Hernandez, J. M.; Josa, M. I.; Pérez-Calero Yzquierdo, A.; Puerta Pelayo, J.; Quintario Olmeda, A.; Redondo, I.; Romero, L.; Soares, M. S.; de Trocóniz, J. F.; Missiroli, M.; Moran, D.; Cuevas, J.; Erice, C.; Fernandez Menendez, J.; Gonzalez Caballero, I.; González Fernández, J. R.; Palencia Cortezon, E.; Sanchez Cruz, S.; Suárez Andrés, I.; Vischia, P.; Vizan Garcia, J. M.; Cabrillo, I. J.; Calderon, A.; Chazin Quero, B.; Curras, E.; Fernandez, M.; Garcia-Ferrero, J.; Gomez, G.; Lopez Virto, A.; Marco, J.; Martinez Rivero, C.; Matorras, F.; Piedra Gomez, J.; Rodrigo, T.; Ruiz-Jimeno, A.; Scodellaro, L.; Trevisani, N.; Vila, I.; Vilar Cortabitarte, R.; Abbaneo, D.; Auffray, E.; Baillon, P.; Ball, A. H.; Barney, D.; Bianco, M.; Bloch, P.; Bocci, A.; Botta, C.; Camporesi, T.; Castello, R.; Cepeda, M.; Cerminara, G.; Chen, Y.; d'Enterria, D.; Dabrowski, A.; Daponte, V.; David, A.; De Gruttola, M.; De Roeck, A.; Di Marco, E.; Dobson, M.; Dorney, B.; du Pree, T.; Dünser, M.; Dupont, N.; Elliott-Peisert, A.; Everaerts, P.; Franzoni, G.; Fulcher, J.; Funk, W.; Gigi, D.; Gill, K.; Glege, F.; Gulhan, D.; Gundacker, S.; Guthoff, M.; Harris, P.; Hegeman, J.; Innocente, V.; Janot, P.; Karacheban, O.; Kieseler, J.; Kirschenmann, H.; Knünz, V.; Kornmayer, A.; Kortelainen, M. J.; Lange, C.; Lecoq, P.; Lourenço, C.; Lucchini, M. T.; Malgeri, L.; Mannelli, M.; Martelli, A.; Meijers, F.; Merlin, J. A.; Mersi, S.; Meschi, E.; Milenovic, P.; Moortgat, F.; Mulders, M.; Neugebauer, H.; Orfanelli, S.; Orsini, L.; Pape, L.; Perez, E.; Peruzzi, M.; Petrilli, A.; Petrucciani, G.; Pfeiffer, A.; Pierini, M.; Racz, A.; Reis, T.; Rolandi, G.; Rovere, M.; Sakulin, H.; Sauvan, J. B.; Schäfer, C.; Schwick, C.; Seidel, M.; Sharma, A.; Silva, P.; Sphicas, P.; Steggemann, J.; Stoye, M.; Tosi, M.; Treille, D.; Triossi, A.; Tsirou, A.; Veckalns, V.; Veres, G. I.; Verweij, M.; Wardle, N.; Zagozdzinska, A.; Zeuner, W. D.; Bertl, W.; Deiters, K.; Erdmann, W.; Horisberger, R.; Ingram, Q.; Kaestli, H. C.; Kotlinski, D.; Langenegger, U.; Rohe, T.; Wiederkehr, S. A.; Bachmair, F.; Bäni, L.; Berger, P.; Bianchini, L.; Casal, B.; Dissertori, G.; Dittmar, M.; Donegà, M.; Grab, C.; Heidegger, C.; Hits, D.; Hoss, J.; Kasieczka, G.; Klijnsma, T.; Lustermann, W.; Mangano, B.; Marionneau, M.; Martinez Ruiz del Arbol, P.; Masciovecchio, M.; Meinhard, M. T.; Meister, D.; Micheli, F.; Musella, P.; Nessi-Tedaldi, F.; Pandolfi, F.; Pata, J.; Pauss, F.; Perrin, G.; Perrozzi, L.; Quittnat, M.; Rossini, M.; Schönenberger, M.; Starodumov, A.; Tavolaro, V. R.; Theofilatos, K.; Vesterbacka Olsson, M. L.; Wallny, R.; Zhu, D. H.; Aarrestad, T. K.; Amsler, C.; Caminada, L.; Canelli, M. F.; De Cosa, A.; Donato, S.; Galloni, C.; Hinzmann, A.; Hreus, T.; Kilminster, B.; Ngadiuba, J.; Pinna, D.; Rauco, G.; Robmann, P.; Salerno, D.; Seitz, C.; Yang, Y.; Zucchetta, A.; Candelise, V.; Doan, T. H.; Jain, Sh.; Khurana, R.; Konyushikhin, M.; Kuo, C. M.; Lin, W.; Pozdnyakov, A.; Yu, S. S.; Kumar, Arun; Chang, P.; Chang, Y. H.; Chao, Y.; Chen, K. F.; Chen, P. H.; Fiori, F.; Hou, W.-S.; Hsiung, Y.; Liu, Y. F.; Lu, R.-S.; Miñano Moya, M.; Paganis, E.; Psallidas, A.; Tsai, J. f.; Asavapibhop, B.; Kovitanggoon, K.; Singh, G.; Srimanobhas, N.; Adiguzel, A.; Bakirci, M. N.; Boran, F.; Damarseckin, S.; Demiroglu, Z. S.; Dozen, C.; Eskut, E.; Girgis, S.; Gokbulut, G.; Guler, Y.; Hos, I.; Kangal, E. E.; Kara, O.; Kiminsu, U.; Oglakci, M.; Onengut, G.; Ozdemir, K.; Ozturk, S.; Polatoz, A.; Sunar Cerci, D.; Turkcapar, S.; Zorbakir, I. S.; Zorbilmez, C.; Bilin, B.; Karapinar, G.; Ocalan, K.; Yalvac, M.; Zeyrek, M.; Gülmez, E.; Kaya, M.; Kaya, O.; Yetkin, E. A.; Cakir, A.; Cankocak, K.; Grynyov, B.; Levchuk, L.; Sorokin, P.; Aggleton, R.; Ball, F.; Beck, L.; Brooke, J. J.; Burns, D.; Clement, E.; Cussans, D.; Flacher, H.; Goldstein, J.; Grimes, M.; Heath, G. P.; Heath, H. F.; Jacob, J.; Kreczko, L.; Lucas, C.; Newbold, D. M.; Paramesvaran, S.; Poll, A.; Sakuma, T.; Seif El Nasr-storey, S.; Smith, D.; Smith, V. J.; Bell, K. W.; Belyaev, A.; Brew, C.; Brown, R. M.; Calligaris, L.; Cieri, D.; Cockerill, D. J. A.; Coughlan, J. A.; Harder, K.; Harper, S.; Olaiya, E.; Petyt, D.; Shepherd-Themistocleous, C. H.; Thea, A.; Tomalin, I. R.; Williams, T.; Baber, M.; Bainbridge, R.; Buchmuller, O.; Bundock, A.; Casasso, S.; Citron, M.; Colling, D.; Corpe, L.; Dauncey, P.; Davies, G.; De Wit, A.; Della Negra, M.; Di Maria, R.; Dunne, P.; Elwood, A.; Futyan, D.; Haddad, Y.; Hall, G.; Iles, G.; James, T.; Lane, R.; Laner, C.; Lyons, L.; Magnan, A.-M.; Malik, S.; Mastrolorenzo, L.; Nash, J.; Nikitenko, A.; Pela, J.; Pesaresi, M.; Raymond, D. M.; Richards, A.; Rose, A.; Scott, E.; Seez, C.; Summers, S.; Tapper, A.; Uchida, K.; Vazquez Acosta, M.; Virdee, T.; Wright, J.; Zenz, S. C.; Cole, J. E.; Hobson, P. R.; Khan, A.; Kyberd, P.; Reid, I. D.; Symonds, P.; Teodorescu, L.; Turner, M.; Borzou, A.; Call, K.; Dittmann, J.; Hatakeyama, K.; Liu, H.; Pastika, N.; Bartek, R.; Dominguez, A.; Buccilli, A.; Cooper, S. I.; Henderson, C.; Rumerio, P.; West, C.; Arcaro, D.; Avetisyan, A.; Bose, T.; Gastler, D.; Rankin, D.; Richardson, C.; Rohlf, J.; Sulak, L.; Zou, D.; Benelli, G.; Cutts, D.; Garabedian, A.; Hakala, J.; Heintz, U.; Hogan, J. M.; Kwok, K. H. M.; Laird, E.; Landsberg, G.; Mao, Z.; Narain, M.; Piperov, S.; Sagir, S.; Spencer, E.; Syarif, R.; Band, R.; Brainerd, C.; Burns, D.; Calderon De La Barca Sanchez, M.; Chertok, M.; Conway, J.; Conway, R.; Cox, P. T.; Erbacher, R.; Flores, C.; Funk, G.; Gardner, M.; Ko, W.; Lander, R.; Mclean, C.; Mulhearn, M.; Pellett, D.; Pilot, J.; Shalhout, S.; Shi, M.; Smith, J.; Squires, M.; Stolp, D.; Tos, K.; Tripathi, M.; Wang, Z.; Bachtis, M.; Bravo, C.; Cousins, R.; Dasgupta, A.; Florent, A.; Hauser, J.; Ignatenko, M.; Mccoll, N.; Saltzberg, D.; Schnaible, C.; Valuev, V.; Bouvier, E.; Burt, K.; Clare, R.; Ellison, J.; Gary, J. W.; Ghiasi Shirazi, S. M. A.; Hanson, G.; Heilman, J.; Jandir, P.; Kennedy, E.; Lacroix, F.; Long, O. R.; Olmedo Negrete, M.; Paneva, M. I.; Shrinivas, A.; Si, W.; Wei, H.; Wimpenny, S.; Yates, B. R.; Branson, J. G.; Cerati, G. B.; Cittolin, S.; Derdzinski, M.; Holzner, A.; Klein, D.; Kole, G.; Krutelyov, V.; Letts, J.; Macneill, I.; Olivito, D.; Padhi, S.; Pieri, M.; Sani, M.; Sharma, V.; Simon, S.; Tadel, M.; Vartak, A.; Wasserbaech, S.; Würthwein, F.; Yagil, A.; Zevi Della Porta, G.; Amin, N.; Bhandari, R.; Bradmiller-Feld, J.; Campagnari, C.; Dishaw, A.; Dutta, V.; Franco Sevilla, M.; George, C.; Golf, F.; Gouskos, L.; Gran, J.; Heller, R.; Incandela, J.; Mullin, S. D.; Ovcharova, A.; Qu, H.; Richman, J.; Stuart, D.; Suarez, I.; Yoo, J.; Anderson, D.; Bendavid, J.; Bornheim, A.; Lawhorn, J. M.; Newman, H. B.; Pena, C.; Spiropulu, M.; Vlimant, J. R.; Xie, S.; Zhu, R. Y.; Andrews, M. B.; Ferguson, T.; Paulini, M.; Russ, J.; Sun, M.; Vogel, H.; Vorobiev, I.; Weinberg, M.; Cumalat, J. P.; Ford, W. T.; Jensen, F.; Johnson, A.; Krohn, M.; Leontsinis, S.; Mulholland, T.; Stenson, K.; Wagner, S. R.; Alexander, J.; Chaves, J.; Chu, J.; Dittmer, S.; Mcdermott, K.; Mirman, N.; Patterson, J. R.; Rinkevicius, A.; Ryd, A.; Skinnari, L.; Soffi, L.; Tan, S. M.; Tao, Z.; Thom, J.; Tucker, J.; Wittich, P.; Zientek, M.; Winn, D.; Abdullin, S.; Albrow, M.; Apollinari, G.; Apresyan, A.; Apyan, A.; Banerjee, S.; Bauerdick, L. A. T.; Beretvas, A.; Berryhill, J.; Bhat, P. C.; Bolla, G.; Burkett, K.; Butler, J. N.; Canepa, A.; Cheung, H. W. K.; Chlebana, F.; Cremonesi, M.; Duarte, J.; Elvira, V. D.; Fisk, I.; Freeman, J.; Gecse, Z.; Gottschalk, E.; Gray, L.; Green, D.; Grünendahl, S.; Gutsche, O.; Harris, R. M.; Hasegawa, S.; Hirschauer, J.; Hu, Z.; Jayatilaka, B.; Jindariani, S.; Johnson, M.; Joshi, U.; Klima, B.; Kreis, B.; Lammel, S.; Lincoln, D.; Lipton, R.; Liu, M.; Liu, T.; Lopes De Sá, R.; Lykken, J.; Maeshima, K.; Magini, N.; Marraffino, J. M.; Maruyama, S.; Mason, D.; McBride, P.; Merkel, P.; Mrenna, S.; Nahn, S.; O'Dell, V.; Pedro, K.; Prokofyev, O.; Rakness, G.; Ristori, L.; Schneider, B.; Sexton-Kennedy, E.; Soha, A.; Spalding, W. J.; Spiegel, L.; Stoynev, S.; Strait, J.; Strobbe, N.; Taylor, L.; Tkaczyk, S.; Tran, N. V.; Uplegger, L.; Vaandering, E. W.; Vernieri, C.; Verzocchi, M.; Vidal, R.; Wang, M.; Weber, H. A.; Whitbeck, A.; Acosta, D.; Avery, P.; Bortignon, P.; Brinkerhoff, A.; Carnes, A.; Carver, M.; Curry, D.; Das, S.; Field, R. D.; Furic, I. K.; Konigsberg, J.; Korytov, A.; Kotov, K.; Ma, P.; Matchev, K.; Mei, H.; Mitselmakher, G.; Rank, D.; Shchutska, L.; Sperka, D.; Terentyev, N.; Thomas, L.; Wang, J.; Wang, S.; Yelton, J.; Linn, S.; Markowitz, P.; Martinez, G.; Rodriguez, J. L.; Ackert, A.; Adams, T.; Askew, A.; Hagopian, S.; Hagopian, V.; Johnson, K. F.; Kolberg, T.; Perry, T.; Prosper, H.; Santra, A.; Yohay, R.; Baarmand, M. M.; Bhopatkar, V.; Colafranceschi, S.; Hohlmann, M.; Noonan, D.; Roy, T.; Yumiceva, F.; Adams, M. R.; Apanasevich, L.; Berry, D.; Betts, R. R.; Cavanaugh, R.; Chen, X.; Evdokimov, O.; Gerber, C. E.; Hangal, D. A.; Hofman, D. J.; Jung, K.; Kamin, J.; Sandoval Gonzalez, I. D.; Tonjes, M. B.; Trauger, H.; Varelas, N.; Wang, H.; Wu, Z.; Zhang, J.; Bilki, B.; Clarida, W.; Dilsiz, K.; Durgut, S.; Gandrajula, R. P.; Haytmyradov, M.; Khristenko, V.; Merlo, J.-P.; Mermerkaya, H.; Mestvirishvili, A.; Moeller, A.; Nachtman, J.; Ogul, H.; Onel, Y.; Ozok, F.; Penzo, A.; Snyder, C.; Tiras, E.; Wetzel, J.; Yi, K.; Blumenfeld, B.; Cocoros, A.; Eminizer, N.; Fehling, D.; Feng, L.; Gritsan, A. V.; Maksimovic, P.; Roskes, J.; Sarica, U.; Swartz, M.; Xiao, M.; You, C.; Al-bataineh, A.; Baringer, P.; Bean, A.; Boren, S.; Bowen, J.; Castle, J.; Khalil, S.; Kropivnitskaya, A.; Majumder, D.; Mcbrayer, W.; Murray, M.; Royon, C.; Sanders, S.; Stringer, R.; Tapia Takaki, J. D.; Wang, Q.; Ivanov, A.; Kaadze, K.; Maravin, Y.; Mohammadi, A.; Saini, L. K.; Skhirtladze, N.; Toda, S.; Rebassoo, F.; Wright, D.; Anelli, C.; Baden, A.; Baron, O.; Belloni, A.; Calvert, B.; Eno, S. C.; Ferraioli, C.; Hadley, N. J.; Jabeen, S.; Jeng, G. Y.; Kellogg, R. G.; Kunkle, J.; Mignerey, A. C.; Ricci-Tam, F.; Shin, Y. H.; Skuja, A.; Tonwar, S. C.; Abercrombie, D.; Allen, B.; Azzolini, V.; Barbieri, R.; Baty, A.; Bi, R.; Bierwagen, K.; Brandt, S.; Busza, W.; Cali, I. A.; D'Alfonso, M.; Demiragli, Z.; Gomez Ceballos, G.; Goncharov, M.; Hsu, D.; Iiyama, Y.; Innocenti, G. M.; Klute, M.; Kovalskyi, D.; Lai, Y. S.; Lee, Y.-J.; Levin, A.; Luckey, P. D.; Maier, B.; Marini, A. C.; Mcginn, C.; Mironov, C.; Narayanan, S.; Niu, X.; Paus, C.; Roland, C.; Roland, G.; Salfeld-Nebgen, J.; Stephans, G. S. F.; Tatar, K.; Velicanu, D.; Wang, J.; Wang, T. W.; Wyslouch, B.; Benvenuti, A. C.; Chatterjee, R. M.; Evans, A.; Hansen, P.; Kalafut, S.; Kao, S. C.; Kubota, Y.; Lesko, Z.; Mans, J.; Nourbakhsh, S.; Ruckstuhl, N.; Rusack, R.; Tambe, N.; Turkewitz, J.; Acosta, J. G.; Oliveros, S.; Avdeeva, E.; Bloom, K.; Claes, D. R.; Fangmeier, C.; Gonzalez Suarez, R.; Kamalieddin, R.; Kravchenko, I.; Monroy, J.; Siado, J. E.; Snow, G. R.; Stieger, B.; Alyari, M.; Dolen, J.; Godshalk, A.; Harrington, C.; Iashvili, I.; Kharchilava, A.; Parker, A.; Rappoccio, S.; Roozbahani, B.; Alverson, G.; Barberis, E.; Hortiangtham, A.; Massironi, A.; Morse, D. M.; Nash, D.; Orimoto, T.; Teixeira De Lima, R.; Trocino, D.; Wang, R.-J.; Wood, D.; Bhattacharya, S.; Charaf, O.; Hahn, K. A.; Mucia, N.; Odell, N.; Pollack, B.; Schmitt, M. H.; Sung, K.; Trovato, M.; Velasco, M.; Dev, N.; Hildreth, M.; Hurtado Anampa, K.; Jessop, C.; Karmgard, D. J.; Kellams, N.; Lannon, K.; Loukas, N.; Marinelli, N.; Meng, F.; Mueller, C.; Musienko, Y.; Planer, M.; Reinsvold, A.; Ruchti, R.; Rupprecht, N.; Smith, G.; Taroni, S.; Wayne, M.; Wolf, M.; Woodard, A.; Alimena, J.; Antonelli, L.; Bylsma, B.; Durkin, L. S.; Flowers, S.; Francis, B.; Hart, A.; Hill, C.; Ji, W.; Liu, B.; Luo, W.; Puigh, D.; Winer, B. L.; Wulsin, H. W.; Benaglia, A.; Cooperstein, S.; Driga, O.; Elmer, P.; Hardenbrook, J.; Hebda, P.; Lange, D.; Luo, J.; Marlow, D.; Mei, K.; Ojalvo, I.; Olsen, J.; Palmer, C.; Piroué, P.; Stickland, D.; Svyatkovskiy, A.; Tully, C.; Malik, S.; Norberg, S.; Barker, A.; Barnes, V. E.; Folgueras, S.; Gutay, L.; Jha, M. K.; Jones, M.; Jung, A. W.; Khatiwada, A.; Miller, D. H.; Neumeister, N.; Schulte, J. F.; Sun, J.; Wang, F.; Xie, W.; Cheng, T.; Parashar, N.; Stupak, J.; Adair, A.; Akgun, B.; Chen, Z.; Ecklund, K. M.; Geurts, F. J. M.; Guilbaud, M.; Li, W.; Michlin, B.; Northup, M.; Padley, B. P.; Roberts, J.; Rorie, J.; Tu, Z.; Zabel, J.; Betchart, B.; Bodek, A.; de Barbaro, P.; Demina, R.; Duh, Y. t.; Ferbel, T.; Galanti, M.; Garcia-Bellido, A.; Han, J.; Hindrichs, O.; Khukhunaishvili, A.; Lo, K. H.; Tan, P.; Verzetti, M.; Ciesielski, R.; Goulianos, K.; Mesropian, C.; Agapitos, A.; Chou, J. P.; Gershtein, Y.; Gómez Espinosa, T. A.; Halkiadakis, E.; Heindl, M.; Hughes, E.; Kaplan, S.; Kunnawalkam Elayavalli, R.; Kyriacou, S.; Lath, A.; Montalvo, R.; Nash, K.; Osherson, M.; Saka, H.; Salur, S.; Schnetzer, S.; Sheffield, D.; Somalwar, S.; Stone, R.; Thomas, S.; Thomassen, P.; Walker, M.; Foerster, M.; Heideman, J.; Riley, G.; Rose, K.; Spanier, S.; Thapa, K.; Bouhali, O.; Castaneda Hernandez, A.; Celik, A.; Dalchenko, M.; De Mattia, M.; Delgado, A.; Dildick, S.; Eusebi, R.; Gilmore, J.; Huang, T.; Kamon, T.; Mueller, R.; Pakhotin, Y.; Patel, R.; Perloff, A.; Perniè, L.; Rathjens, D.; Safonov, A.; Tatarinov, A.; Ulmer, K. A.; Akchurin, N.; Damgov, J.; De Guio, F.; Dragoiu, C.; Dudero, P. R.; Faulkner, J.; Gurpinar, E.; Kunori, S.; Lamichhane, K.; Lee, S. W.; Libeiro, T.; Peltola, T.; Undleeb, S.; Volobouev, I.; Wang, Z.; Greene, S.; Gurrola, A.; Janjam, R.; Johns, W.; Maguire, C.; Melo, A.; Ni, H.; Sheldon, P.; Tuo, S.; Velkovska, J.; Xu, Q.; Arenton, M. W.; Barria, P.; Cox, B.; Hirosky, R.; Ledovskoy, A.; Li, H.; Neu, C.; Sinthuprasith, T.; Sun, X.; Wang, Y.; Wolfe, E.; Xia, F.; Clarke, C.; Harr, R.; Karchin, P. E.; Sturdy, J.; Zaleski, S.; Belknap, D. A.; Buchanan, J.; Caillol, C.; Dasu, S.; Dodd, L.; Duric, S.; Gomber, B.; Grothe, M.; Herndon, M.; Hervé, A.; Hussain, U.; Klabbers, P.; Lanaro, A.; Levine, A.; Long, K.; Loveless, R.; Pierro, G. A.; Polese, G.; Ruggles, T.; Savin, A.; Smith, N.; Smith, W. H.; Taylor, D.; Woods, N.; CMS Collaboration

2018-01-01

The cross sections for the production of t t bar b b bar and t t bar jj events and their ratio σ t t bar b b bar /σ t t bar jj are measured using data corresponding to an integrated luminosity of 2.3 fb-1collected in pp collisions at √{ s } = 13 TeV with the CMS detector at the LHC. Events with two leptons (e or μ) and at least four reconstructed jets, including at least two identified as b quark jets, in the final state are selected. In the full phase space, the measured ratio is 0.022 ± 0.003(stat) ± 0.006(syst), the cross section σ t t bar b b bar is 4.0 ± 0.6(stat) ± 1.3(syst) pb and σ t t bar jj is 184 ± 6(stat) ± 33(syst) pb. The measurements are compared with the standard model expectations obtained from a POWHEG simulation at next-to-leading-order interfaced with PYTHIA.

Subsurface flow in lowland river gravel bars

NASA Astrophysics Data System (ADS)

Bray, E. N.; Dunne, T.

2017-09-01

Geomorphic and hydraulic processes, which form gravel bars in large lowland rivers, have distinctive characteristics that control the magnitude and spatial patterns of infiltration and exfiltration between rivers and their immediate subsurface environments. We present a bedform-infiltration relation together with a set of field measurements along two reaches of the San Joaquin River, CA to illustrate the conditions required for infiltration and exfiltration of flow between a stream and its undulating bed, and a numerical model to investigate the factors that affect paths and residence times of flow through barforms at different discharges. It is shown that asymmetry of bar morphology is a first-order control on the extent and location of infiltration, which would otherwise produce equal areas of infiltration and exfiltration under the assumption of sinusoidal bedforms. Hydraulic conductivity varies by orders of magnitude due to fine sediment accumulation and downstream coarsening related to the process of bar evolution. This systematic variability not only controls the magnitude of infiltration, but also the residence time of flow through the bed. The lowest hydraulic conductivity along the reach occurred where the difference between the topographic gradient and the water-surface gradient is at a maximum and thus where infiltration would be greatest into a homogeneous bar, indicating the importance of managing sand supply to maintain the ventilation and flow through salmon spawning riffles. Numerical simulations corroborate our interpretation that infiltration patterns and rates are controlled by distinctive features of bar morphology.

Long-term clinical and prosthetic outcomes of soft liner and clip attachments for bar/implant overdentures: a randomised controlled clinical trial.

PubMed

ELsyad, M A; Shaheen, N H; Ashmawy, T M

2017-06-01

Long-term clinical and prosthetic outcomes of soft liner attachments for bar/implant overdentures were not sufficiently investigated. The aim of this trial was to evaluate clinical and prosthetic outcomes of resilient liner and clip attachments for bar/implant-retained mandibular overdenture after 7 years. Thirty edentulous male participants received two implants in the canine areas of the mandible. Three months later, implants were splinted with a resilient bar. Mandibular overdentures were connected to the bars with either clip (CR group, n = 15) or resilient liner (RR group, n = 15) attachments. Plaque index (PI), gingival index (GI), probing depth (PD), vertical bone loss (VBL), horizontal bone loss (HBLO) and prosthetic complications (PCs) were evaluated at denture delivery (T0), 6 (T 6m ), 12 (T1), 24 (T2), 36 (T3), 48 (T4), 60 (T5), 72 (T6) and 84 (T7) months after insertion. PI and GI increased significantly with time for CR and decreased significantly for RR (P < 0·001). PD increased at T1 (CR) and T6 m (RR) and then decreased thereafter (P < 0·05). VBL increased significantly with time in both groups (P < 0·005). HBLO increased at T2 (CR) and T1 (RR) and then decreased thereafter. CR recorded significant higher PI, GI, PD, VBLO and HBLO compared to RR at all observation times (P < 0·042). The survival rates were 96·6% and 100% for CR and RR after 7 years. The most common PCs for CR and RR were clip wears and separation of the resilient liner from the denture base, respectively. Within the limitations of this study, resilient liner attachments are recommended for bar/implant-retained mandibular overdentures than clip attachments in terms of peri-implant tissue health and prosthetic complications after 7 years. © 2017 John Wiley & Sons Ltd.

Kinematic imprints from the bar and spiral structures in the galatic disk

NASA Astrophysics Data System (ADS)

Figueras, F.; Antoja, T.; Valenzuela, O.; Romero-Gómez, M.; Pichardo, B.; Moreno, E.

2011-12-01

At 140 years of the discovery of the moving groups, these stellar streams are emerging as powerful tools to constrain the models for the spiral arms and the Galactic bar in the Gaia era. From the kinematic-age-metallicity analysis in the solar neighbourhood it is now well established that some of these kinematic structures have a dynamical origin, different from the classical cluster disruption hypothesis. Test particle simulations allow us to definitively establish that these local structures can be created by the dynamical resonances of material spiral arms and not exclusively by the Galactic bar. First studies to evaluate the capabilities of the future Gaia data to detect and characterize moving groups at 2-6 kpc from the solar neighborhood are discussed.

75 FR 10687 - Regulated Navigation Areas; Bars Along the Coasts of Oregon and Washington; Correction

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-09

..., 3306, 3703; 50 U.S.C. 191, 195; 33 CFR 1.05-1(g), 6.04-1, 6.04-6, and 160.5; Pub. L. 107-295, 116 Stat... 22A prior to crossing the bar between sunset and sunrise. * * * * * * * * Dated: February 17, 2010. G.T. Blore, Rear Admiral, U.S. Coast Guard, Commander, Thirteenth Coast Guard District. [FR Doc. 2010...

Tobacco related bar promotions: insights from tobacco industry documents.

PubMed

Katz, S K; Lavack, A M

2002-03-01

To examine the tobacco industry's use of bar promotions, including their target groups, objectives, strategies, techniques, and results. Over 2000 tobacco industry documents available as a result of the Master Settlement Agreement were reviewed on the internet at several key web sites using keyword searches that included "bar", "night", "pub", "party", and "club". The majority of the documents deal with the US market, with a minor emphasis on Canadian and overseas markets. The documents indicate that bar promotions are important for creating and maintaining brand image, and are generally targeted at a young adult audience. Several measures of the success of these promotions are used, including number of individuals exposed to the promotion, number of promotional items given away, and increased sales of a particular brand during and after the promotion. Bar promotions position cigarettes as being part of a glamorous lifestyle that includes attendance at nightclubs and bars, and appear to be highly successful in increasing sales of particular brands.

Eliminating smoking in bars, restaurants, and gaming clubs in California: BREATH, the California Smoke-Free Bar Program.

PubMed

Kiser, D; Boschert, T

2001-01-01

On January 1, 1998, California became the first state in the country to prohibit indoor smoking in nightspots, bars, bar/restaurant combinations, bingo parlors, cardrooms, and casinos on a statewide basis. This paper describes the activities which achieved this result, based on a program with three main goals: Ease the transition for business owners; Activate public support for the law; Defeat tobacco industry efforts to undermine the law. Important lessons learned from this campaign are presented.

Photoassociation studies of ultracold NaCs from the Cs 6(2)P(3/2) asymptote.

PubMed

Wakim, A; Zabawa, P; Bigelow, N P

2011-11-14

A combination of pulsed depletion spectroscopy and photoassociation spectroscopy is utilized to assign photoassociation spectra of NaCs. These methods investigate the ab initio Ω = 2 potential energy curve and indicate a previously unknown avoided crossing between the (3)Ω = 1 and (4)Ω = 1 electronic states. We present rotational assignments of deeply bound singlet ground state molecules, an improved C(6) coefficient for the (4)Ω = 1 and assignments for all twenty-three photoassociation resonances detuned from the Cs 6(2)P(3/2) asymptote.

Optimisation of gellan gum edible coating for ready-to-eat mango (Mangifera indica L.) bars.

PubMed

Danalache, Florina; Carvalho, Claudia Y; Alves, Vitor D; Moldão-Martins, Margarida; Mata, Paulina

2016-03-01

The optimisation of an edible coating based on low acyl (L)/high acyl (H) gellan gum for ready-to-eat mango bars was performed through a central composite rotatable design (CCRD). The independent variables were the concentration of gellan (L/H90/10) and the concentration of Ca(2+) in the coating solution, as well as the storage time after coating application. The response variables studied were the coating thickness, mango bars firmness, syneresis, and colour alterations. Gellan concentration was the independent variable that most influenced the thickness of the coating. Syneresis was quite low for the conditions tested (<1.64%). Similarly, the colour alterations were low during the entire storage time (ΔE<5). Considering the model predictions, 1.0%wt L/H90/10 with addition of 6 mM Ca(2+) could represent the optimal coating formulation for the mango bars. The release of eight volatile compounds from the uncoated and coated mango bars with the selected formulation was analysed by Headspace - Solid Phase Micro Extraction-Gas Chromatography during 9 days of refrigerated storage. This work showed that the coating can improve mango bars sensory characteristics (appearance and firmness) and stability in terms of syneresis, colour and volatiles content during storage increasing the commercial value of the final product. Crown Copyright © 2015. Published by Elsevier B.V. All rights reserved.

Russian BAR/EXPERT experiment

NASA Image and Video Library

2009-08-28

ISS020-E-035016 (27 Aug. 2009) --- Russian cosmonaut Gennady Padalka, Expedition 20 commander, uses the Russian BAR/EXPERT science payload to take various environmental measurements in the Zvezda Service Module of the International Space Station.

Russian BAR/EXPERT experiment

NASA Image and Video Library

2009-08-28

ISS020-E-035017 (27 Aug. 2009) --- Russian cosmonaut Gennady Padalka, Expedition 20 commander, uses the Russian BAR/EXPERT science payload to take various environmental measurements in the Zvezda Service Module of the International Space Station.

Energy Drinks and Food Bars: Power or Hype?

MedlinePlus

... Staying Safe Videos for Educators Search English Español Energy Drinks and Food Bars: Power or Hype? KidsHealth / ... nutritivas: ¿Energía o mera exageración? The Buzz on Energy Foods Energy drinks and nutrition bars often make ...

5 CFR 9701.205 - Bar on collective bargaining.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 5 Administrative Personnel 3 2010-01-01 2010-01-01 false Bar on collective bargaining. 9701.205 Section 9701.205 Administrative Personnel DEPARTMENT OF HOMELAND SECURITY HUMAN RESOURCES MANAGEMENT... HUMAN RESOURCES MANAGEMENT SYSTEM Classification General § 9701.205 Bar on collective bargaining. As...

Analysis of preservatives with different polarities in beverage samples by dual-phase dual stir bar sorptive extraction combined with high-performance liquid chromatography.

PubMed

Xu, Jin; Chen, Beibei; He, Man; Hu, Bin

2013-02-22

A new concept of "dual-phase dual stir bar sorptive extraction (SBSE)" was proposed to simultaneously extract six preservatives with different polarities (logKo/w values of 1.27-3.41), namely, benzoic acid (BA), sorbic acid (SA), methyl p-hydroxybenzoate (MP), ethyl p-hydroxybenzoate (EP), propyl p-hydroxybenzoate (PP), and butyl p-hydroxybenzoate (BP). The dual-phase dual SBSE apparatus was consisted of two differently coated stir bars, a 3-aminopropyltriethoxysilane (APTES)-hydroxy-terminated silicone oil (OH-TSO)-coated stir bar that was prepared by sol-gel technique and a C(18) silica (C(18))-polydimethylsiloxane (PDMS)-coated stir bar that was prepared by adhesion. In dual-phase dual SBSE, the two stir bars with different coatings were placed in the same sample solution for the simultaneous extraction of the target analytes with different polarities, and then the bars were desorbed in the same desorption solvent. The extraction performance of the dual-phase dual SBSE for the six preservatives was evaluated by comparing with the conventional SBSE (individual stir bar) with different coatings, including commercial PDMS, homemade PDMS, C(18)-APTES-OH-TSO, APTES-OH-TSO, and C(18)-PDMS. The experimental results showed that the dual-phase dual SBSE had the highest extraction efficiency for the six target preservatives. Based on this fact, a novel method by combining the dual-phase dual SBSE which was consisted of the APTES-OH-TSO-coated and C(18)-PDMS-coated stir bars with high-performance liquid chromatography-ultraviolet detection (HPLC-UV) was developed for the simultaneous analysis of six target beverage preservatives in beverages. Under optimal conditions, the limits of detection (LODs) for six target preservatives ranged from 0.6 to 2.7 μgL(-1) with the relative standard deviations (RSDs) of 4.6-9.2% (C(BA,SA)=5 μgL(-1),C(MP)=20 μgL(-1),C(EP,PP,BP)=10 μgL(-1), n=7). The enrichment factors (EFs) were approximately 16-42-fold (theoretical EF was 50-fold

Discrete shear-transformation-zone plasticity modeling of notched bars

NASA Astrophysics Data System (ADS)

Kondori, Babak; Amine Benzerga, A.; Needleman, Alan

2018-02-01

Plane strain tension analyses of un-notched and notched bars are carried out using discrete shear transformation zone plasticity. In this framework, the carriers of plastic deformation are shear transformation zones (STZs) which are modeled as Eshelby inclusions. Superposition is used to represent a boundary value problem solution in terms of discretely modeled Eshelby inclusions, given analytically for an infinite elastic medium, and an image solution that enforces the prescribed boundary conditions. The image problem is a standard linear elastic boundary value problem that is solved by the finite element method. Potential STZ activation sites are randomly distributed in the bars and constitutive relations are specified for their evolution. Results are presented for un-notched bars, for bars with blunt notches and for bars with sharp notches. The computed stress-strain curves are serrated with the magnitude of the associated stress-drops depending on bar size, notch acuity and STZ evolution. Cooperative deformation bands (shear bands) emerge upon straining and, in some cases, high stress levels occur within the bands. Effects of specimen geometry and size on the stress-strain curves are explored. Depending on STZ kinetics, notch strengthening, notch insensitivity or notch weakening are obtained. The analyses provide a rationale for some conflicting findings regarding notch effects on the mechanical response of metallic glasses.

[x, p] = i{h_bar} ?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tang, Jau

1996-03-01

Heisenberg`s commutation relation for position x and momentum p, and its validity for relativistic harmonic oscillators are examined, using the techniques of Lie algebra and dual-bosonic representation of x, p and the Hamiltonian H. A modification with [x, p] =i{h_bar}({minus_plus} 1 + H/m{sub 0}c{sup 2}) is proposed for a particle and an antiparticle in a harmonic potential. For a 2 {times} 2 matrix representation for x, p and H operators, the quantized eigenenergy E is given by (E - m{sub 0}c{sup 2})/{h_bar}{omega} = 3/2, 5/2, 7/2, ..., where 1/2 is not allowed.

Effects of a groyne field on inner bar dynamics: Anglet, France

NASA Astrophysics Data System (ADS)

de Santiago, Inaki; Morichon, Denis; Arnould, Philippe

2017-04-01

Groynes are usually designed to limit beach erosion by mitigating longshore sediment transport. However, little is known about their side effects on inner-bar morphodynamics in double sandbar systems. While most of the studies are focused on natural systems where the outer-bar morphology drives inner-bar dynamics (offshore to nearshore process), this work focuses on the role of groynes on the inner bar dynamics (nearshore to offshore process). The study is based on 3-years field observations carried out at the beach of Anglet in the south-west of France. This engineered beach is 4 km long, limited by a rocky headland in the south and a 1 km long jetty at the entrance of the Adour river in the North. The study area concerns the south part of the beach and includes a series of four groynes, unevenly spaced and extending about 100 m seaward. Morphology changes observations were derived from images collected with a video system (http://sirena.univ-pau.fr/), and bi-annual topo-Bathymetric surveys. A special attention was paid to study the mechanisms controlling the observed morphology changes using the XBeach numerical model. Data analysis reveals that the study site is dominated by a double sandbar system. Both bars can evolve from reasonably alongshore-uniform to crescentic bars. Surprisingly, the beach may show episodes where the inner bar evolves from alonghsore uniform to non-uniform despite an alongshore uniform outer bar. Numerical results corroborate that the formation of inner bar crescentic features can be formed without the presence of an outer non-uniform bar under certain wave conditions for the study site. This study shows that inner bar evolution in the presence of groynes can be controlled by topographic rip channels and not only by morphological coupling as usually observed on natural double sandbar systems.

Russian BAR/EXPERT experiment

NASA Image and Video Library

2009-08-28

ISS020-E-035022 (27 Aug. 2009) --- Russian cosmonaut Roman Romanenko, Expedition 20 flight engineer, uses the Russian BAR/EXPERT science payload to take various environmental measurements in the Zvezda Service Module of the International Space Station.

Alluvial Bars of the Obed Wild and Scenic River, Tennessee

USGS Publications Warehouse

Wolfe, W.J.; Fitch, K.C.; Ladd, D.E.

2007-01-01

In 2004, the U.S. Geological Survey (USGS) and the National Park Service (NPS) initiated a reconnaissance study of alluvial bars along the Obed Wild and Scenic River (Obed WSR), in Cumberland and Morgan Counties, Tennessee. The study was partly driven by concern that trapping of sand by upstream impoundments might threaten rare, threatened, or endangered plant habitat by reducing the supply of sediment to the alluvial bars. The objectives of the study were to: (1) develop a preliminary understanding of the distribution, morphology, composition, stability, and vegetation structure of alluvial bars along the Obed WSR, and (2) determine whether evidence of human alteration of sediment dynamics in the Obed WSR warrants further, more detailed examination. This report presents the results of the reconnaissance study of alluvial bars along the Obed River, Clear Creek, and Daddys Creek in the Obed WSR. The report is based on: (1) field-reconnaissance visits by boat to 56 alluvial bars along selected reaches of the Obed River and Clear Creek; (2) analysis of aerial photographs, topographic and geologic maps, and other geographic data to assess the distribution of alluvial bars in the Obed WSR; (3) surveys of topography, surface particle size, vegetation structure, and ground cover on three selected alluvial bars; and (4) analysis of hydrologic records.

Washing with contaminated bar soap is unlikely to transfer bacteria.

PubMed Central

Heinze, J. E.; Yackovich, F.

1988-01-01

Recent reports of the isolation of microorganisms from used soap bars have raised the concern that bacteria may be transferred from contaminated soap bars during handwashing. Since only one study addressing this question has been published, we developed an additional procedure to test this concern. In our new method prewashed and softened commercial deodorant soap bars (0.8% triclocarban) not active against Gram-negative bacteria were inoculated with Escherichia coli and Pseudomonas aeruginosa to give mean total survival levels of 4.4 X 10(5) c.f.u. per bar which was 70-fold higher than those reported on used soap bars. Sixteen panelists were instructed to wash with the inoculated bars using their normal handwashing procedure. After washing, none of the 16 panelists had detectable levels of either test bacterium on their hands. Thus, the results obtained using our new method were in complete agreement with those obtained with the previously published method even though the two methods differ in a number of procedural aspects. These findings, along with other published reports, show that little hazard exists in routine handwashing with previously used soap bars and support the frequent use of soap and water for handwashing to prevent the spread of disease. PMID:3402545

Performance comparison of MoNA and LISA neutron detectors

NASA Astrophysics Data System (ADS)

Purtell, Kimberly; Rethman, Kaitlynne; Haagsma, Autumn; Finck, Joseph; Smith, Jenna; Snyder, Jesse

2010-11-01

In 2002 eight primarily undergraduate institutions constructed and tested the Modular Neutron Array (MoNA) which has been used to detect high energy neutrons at the National Superconducting Cyclotron Laboratory (NSCL). Nine institutions have now designed, constructed and tested the Large-area multi-Institutional Scintillator Array (LISA) neutron detector which will be used at the NSCL and the future Facility for Rare Isotope Beams (FRIB). Both detectors are comprised of 144 detector modules. Each module is a 200 x 10 x 10 cm^3 bar organic plastic scintillator with a photomultiplier tube mounted on each end. Using cosmic rays and a gamma source, we compared the performance of MoNA and LISA by using the same electronics to check light attenuation, position resolution, rise times, and cosmic ray peak widths. Results will be presented.

5 CFR 9701.305 - Bar on collective bargaining.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 5 Administrative Personnel 3 2010-01-01 2010-01-01 false Bar on collective bargaining. 9701.305 Section 9701.305 Administrative Personnel DEPARTMENT OF HOMELAND SECURITY HUMAN RESOURCES MANAGEMENT... HUMAN RESOURCES MANAGEMENT SYSTEM Pay and Pay Administration General § 9701.305 Bar on collective...

Icing research tunnel rotating bar calibration measurement system

NASA Technical Reports Server (NTRS)

Gibson, Theresa L.; Dearmon, John M.

1993-01-01

In order to measure icing patterns across a test section of the Icing Research Tunnel, an automated rotating bar measurement system was developed at the NASA Lewis Research Center. In comparison with the previously used manual measurement system, this system provides a number of improvements: increased accuracy and repeatability, increased number of data points, reduced tunnel operating time, and improved documentation. The automated system uses a linear variable differential transformer (LVDT) to measure ice accretion. This instrument is driven along the bar by means of an intelligent stepper motor which also controls data recording. This paper describes the rotating bar calibration measurement system.

Bar coded retroreflective target

DOEpatents

Vann, Charles S.

2000-01-01

This small, inexpensive, non-contact laser sensor can detect the location of a retroreflective target in a relatively large volume and up to six degrees of position. The tracker's laser beam is formed into a plane of light which is swept across the space of interest. When the beam illuminates the retroreflector, some of the light returns to the tracker. The intensity, angle, and time of the return beam is measured to calculate the three dimensional location of the target. With three retroreflectors on the target, the locations of three points on the target are measured, enabling the calculation of all six degrees of target position. Until now, devices for three-dimensional tracking of objects in a large volume have been heavy, large, and very expensive. Because of the simplicity and unique characteristics of this tracker, it is capable of three-dimensional tracking of one to several objects in a large volume, yet it is compact, light-weight, and relatively inexpensive. Alternatively, a tracker produces a diverging laser beam which is directed towards a fixed position, and senses when a retroreflective target enters the fixed field of view. An optically bar coded target can be read by the tracker to provide information about the target. The target can be formed of a ball lens with a bar code on one end. As the target moves through the field, the ball lens causes the laser beam to scan across the bar code.

Release of iron, zinc, and lead from common iron construction bars and zinc metallic bars in water solutions and meals.

PubMed

Lechtig, Aarón; Lòpez de Romaña, Daniel; Boy, Erick; Vargas, Alejandro; Rosas del Portal, Mauricio; Huaylinos, María Luisa

2007-12-01

The use of iron pots has decreased the prevalence of anemia. To investigate the release of iron, zinc, and lead from metallic iron and zinc bars incubated in water and in meals. Iron, zinc, and lead concentrations were measured at different incubation conditions in water and in meals. The iron concentration in water was 1.26 mg/L after incubation with one iron bar at pH 7 and 100 degrees C for 20 minutes and in meals was 0.97 mg per 100 g of wet meals, rich in phytate, cooking at 100 degrees C during 20 minutes. The maximum contents were 7720 mg/L of iron and 1826 mg/L of zinc in vinegar at pH 3 and 20 degrees C after 90 and 32 days, respectively. Lead was released from the bars, but at concentrations well below the upper tolerable limits. In outreach populations, the use of iron and zinc metallic bars in water and meals could contribute to sustainable, very low-cost prevention of iron and zinc deficiencies, and home-fortified vinegar could be used for treatment of both deficiencies. Field trials should be performed to determine the impact that the use of iron and zinc metallic bars in water and meals might have on the iron and zinc status of population groups.

Bad nights or bad bars? Multi-level analysis of environmental predictors of aggression in late-night large-capacity bars and clubs.

PubMed

Graham, Kathryn; Bernards, Sharon; Osgood, D Wayne; Wells, Samantha

2006-11-01

To clarify environmental predictors of bar-room aggression by differentiating relationships due to nightly variations versus across bar variations, frequency versus severity of aggression and patron versus staff aggression. Male-female pairs of researcher-observers conducted 1334 observations in 118 large capacity (> 300) bars and clubs in Toronto, Canada. Observers independently rated aspects of the environment (e.g. crowding) at every visit and wrote detailed narratives of each incident of aggression that occurred. Measures of severity of aggression for the visit were calculated by aggregating ratings for each person in aggressive incidents. Although bivariate analyses confirmed the significance of most environmental predictors of aggression identified in previous research, multivariate analyses identified the following key visit-level predictors (controlling for bar-level relationships): rowdiness/permissive environment and people hanging around after closing predicted both frequency and severity of aggression; sexual activity, contact and competition and people with two or more drinks at closing predicted frequency but not severity of aggression; lack of staff monitoring predicted more severe patron aggression, while having more and better coordinated staff predicted more severe staff aggression. Intoxication of patrons was significantly associated with more frequent and severe patron aggression at the bar level (but not at the visit level) in the multivariate analyses and negatively associated with severity of staff aggression at the visit level. The results demonstrate clearly the importance of the immediate environment (not just the type of bar or characteristics of usual patrons) and the importance of specific environmental factors, including staff behaviour, in predicting both frequency and severity of aggression.

Visual mining geo-related data using pixel bar charts

NASA Astrophysics Data System (ADS)

Hao, Ming C.; Keim, Daniel A.; Dayal, Umeshwar; Wright, Peter; Schneidewind, Joern

2005-03-01

A common approach to analyze geo-related data is using bar charts or x-y plots. They are intuitive and easy to use. But important information often gets lost. In this paper, we introduce a new interactive visualization technique called Geo Pixel Bar Charts, which combines the advantages of Pixel Bar Charts and interactive maps. This technique allows analysts to visualize large amounts of spatial data without aggregation and shows the geographical regions corresponding to the spatial data attribute at the same time. In this paper, we apply Geo Pixel Bar Charts to visually mining sales transactions and Internet usage from different locations. Our experimental results show the effectiveness of this technique for providing data distribution and exceptions from the map.

Quantifying the (X/peanut)-shaped structure of the Milky Way - new constraints on the bar geometry

NASA Astrophysics Data System (ADS)

Ciambur, Bogdan C.; Graham, Alister W.; Bland-Hawthorn, Joss

2017-11-01

The nature, size and orientation of the Milky Way's bar and `bulge' have been the subject of conflicting interpretations in the literature. Here, we present a novel approach to inferring the properties of the long bar, which extends beyond the inner `bulge', by using information encoded in the Galaxy's X/peanut (X/P)-shaped structure. We perform a quantitative analysis of the X/P feature seen in WISE wide-field images, at 3.4 and 4.6 μm, by measuring the deviations of the isophotes from pure ellipses and using the radial profile of their sixth-order Fourier harmonic (cosine term, B6). In addition to the vertical height and integrated `strength' of the observed X/P instability, we report an intrinsic radius RΠ,int = 1.67 ± 0.27 kpc, and an orientation angle of α = 37°+7°-10° with respect to our line of sight to the Galactic Centre. Based on X/P structures observed in other galaxies, we assume that the Milky Way's X/P structure is intrinsically symmetric, aligned with the long Galactic bar, and that its size is correlated with this bar. The implications for the Galactic bar are that it is oriented at a 37° angle and has a radius of ≈4.2 kpc, but possibly as low as ≈3.2 kpc. We have investigated how the Milky Way's X/P structure compares with analogues in other galaxies, and find that it is consistent with recently established scaling relations, though with a marginally stronger X/P instability than expected. We additionally perform a photometric decomposition of the Milky Way's major axis surface brightness profile, accounting for spiral structure, and determine an average disc scalelength of h = 2.54 ± 0.16 kpc.

Intelligent bar chart plagiarism detection in documents.

PubMed

Al-Dabbagh, Mohammed Mumtaz; Salim, Naomie; Rehman, Amjad; Alkawaz, Mohammed Hazim; Saba, Tanzila; Al-Rodhaan, Mznah; Al-Dhelaan, Abdullah

2014-01-01

This paper presents a novel features mining approach from documents that could not be mined via optical character recognition (OCR). By identifying the intimate relationship between the text and graphical components, the proposed technique pulls out the Start, End, and Exact values for each bar. Furthermore, the word 2-gram and Euclidean distance methods are used to accurately detect and determine plagiarism in bar charts.

Intelligent Bar Chart Plagiarism Detection in Documents

PubMed Central

Al-Dabbagh, Mohammed Mumtaz; Salim, Naomie; Alkawaz, Mohammed Hazim; Saba, Tanzila; Al-Rodhaan, Mznah; Al-Dhelaan, Abdullah

2014-01-01

This paper presents a novel features mining approach from documents that could not be mined via optical character recognition (OCR). By identifying the intimate relationship between the text and graphical components, the proposed technique pulls out the Start, End, and Exact values for each bar. Furthermore, the word 2-gram and Euclidean distance methods are used to accurately detect and determine plagiarism in bar charts. PMID:25309952

The Stability Of Disk Barred Galaxies Over the Past 7 Billion Years

NASA Astrophysics Data System (ADS)

Tapia, Amauri; Simmons, Brooke

2017-01-01

A recently released model of interacting disk galaxies provides a hypothesis for the origins of off center bars in disks. No systematic search for offset bars in the early universe has yet been undertaken. The Galaxy Zoo project has produced data regarding the large-scale bars of many galaxies. Using this data alongside images collected by the Hubble Space Telescope and other sources, we have examined 5190 galaxies for signatures of off-centered bars. Less than 5 percent of the sample shows clear signs of an offset bar. We describe their overall properties of this sub-sample and compare the properties of galaxies with offset bars to those with centered bars. We assess the feasibility of the proposed model and place these galaxies in the context of the overall evolution of galaxies.

Investigating Storm-Induced Total Water Levels on Complex Barred Beaches

NASA Astrophysics Data System (ADS)

Cohn, N.; Ruggiero, P.; Walstra, D.

2013-12-01

River Littoral Cell (USA), Duck, NC (USA), Hasaki (Japan), and the Netherlands, a net offshore bar migration (NOM) cycle has been observed whereby bars migrate seaward across the surf zone and decay offshore on interannual cycles. Depending on the stage of the cycle, the number and configuration of the bars may differ widely. For example in the Columbia River Littoral Cell there are typically 2 to 4 nearshore bars. In 1999, the outermost bar crest was located in a water depth of 6.5 m (relative to MLLW) while in 2009 it was located only in 3 m of water. Such large differences in nearshore morphology clearly influence wave breaking patterns and have the potential for influencing the corresponding wave runup as well. Here we apply a numerical, short-wave averaged yet long-wave resolving, non-linear hydrodynamic model (XBeach) to investigate the role that real world (non-synthetic), complex morphologies exert on TWLs. Model simulations under moderate to extreme wave forcing conditions are being used to develop relationships between offshore wave conditions, bar configuration, and runup extent. Additionally, we are exploring how, under the same wave conditions, a particular location may be more vulnerable to flooding simply based on the stage of the NOM cycle. Comparisons with the Stockdon et al. (2006) runup equation will be made to assess traditional empirical approaches relative to model predictions.

Access to Bathtub Grab Bars: Evidence of a Policy Gap

ERIC Educational Resources Information Center

Birkett, Nicholas; Nair, Rama; Murphy, Maureen; Roberge, Ginette; Lockett, Donna

2006-01-01

This paper examines access to bathtub grab bars in privately and publicly owned apartment buildings and explores the profile of seniors who have access to bathtub grab bars. Results indicate that bathtub grab bars were significantly more prevalent in apartments that were publicly owned (91.3%) as compared to privately owned (37.8%) (p lesser than…

The Bologna Annotation Resource (BAR 3.0): improving protein functional annotation

PubMed Central

Casadio, Rita

2017-01-01

Abstract BAR 3.0 updates our server BAR (Bologna Annotation Resource) for predicting protein structural and functional features from sequence. We increase data volume, query capabilities and information conveyed to the user. The core of BAR 3.0 is a graph-based clustering procedure of UniProtKB sequences, following strict pairwise similarity criteria (sequence identity ≥40% with alignment coverage ≥90%). Each cluster contains the available annotation downloaded from UniProtKB, GO, PFAM and PDB. After statistical validation, GO terms and PFAM domains are cluster-specific and annotate new sequences entering the cluster after satisfying similarity constraints. BAR 3.0 includes 28 869 663 sequences in 1 361 773 clusters, of which 22.2% (22 241 661 sequences) and 47.4% (24 555 055 sequences) have at least one validated GO term and one PFAM domain, respectively. 1.4% of the clusters (36% of all sequences) include PDB structures and the cluster is associated to a hidden Markov model that allows building template-target alignment suitable for structural modeling. Some other 3 399 026 sequences are singletons. BAR 3.0 offers an improved search interface, allowing queries by UniProtKB-accession, Fasta sequence, GO-term, PFAM-domain, organism, PDB and ligand/s. When evaluated on the CAFA2 targets, BAR 3.0 largely outperforms our previous version and scores among state-of-the-art methods. BAR 3.0 is publicly available and accessible at http://bar.biocomp.unibo.it/bar3. PMID:28453653

Blue-green tunable color of Ce3+/Tb3+ coactivated NaBa3La3Si6O20 phosphor via energy transfer

PubMed Central

Jia, Zhen; Xia, Mingjun

2016-01-01

A series of color tunable phosphors NaBa3La3Si6O20:Ce3+, Tb3+ were synthesized via the high-temperature solid-state method. NaBa3La3Si6O20 crystallizes in noncentrosymmetric space group Ama2 with the cell parameters of a = 14.9226(4) Å, b = 24.5215(5) Å and c = 5.6241(2) Å by the Rietveld refinement method. The Ce3+ ions doped NaBa3La3Si6O20 phosphors have a strong absorption band from 260 to 360 nm and show near ultraviolet emission light centered at 378 nm. The Ce3+ and Tb3+ ions coactivated phosphors exhibit color tunable emission light from deep blue to green by adjusting the concentration of the Tb3+ ions. An energy transfer of Ce3+ → Tb3+ investigated by the photoluminescence properties and lifetime decay, is demonstrated to be dipole–quadrupole interaction. These results indicate the NaBa3La3Si6O20:Ce3+, Tb3+ phosphors can be considered as potential candidates for blue-green components for white light emitting diodes. PMID:27628111

Numerical modeling of barred spiral galaxies

NASA Astrophysics Data System (ADS)

Moore, Elizabeth Mary

1992-08-01

A two-component, self-consistent computer code to model spiral galaxies was written and tested and a method of inducing and controlling bar formation is developed. This work presents a departure from former modeling work done at the University of Florida, which depended on the beam scheme, a hydrodynamical code with a number of limitations. In particular, only the gas component could be modeled, no self-gravitational forces were included, and the viscosity inherent to the code could not be controlled easily. These shortcomings are overcome in the new algorithm. Most importantly, an attempt has been made to keep the models self-consistent. No perturbing potentials are imposed or required to excite bar and spiral structure. The code can model both the stellar and the gaseous component of a spiral galaxy. The stellar component feels only gravitational forces, while the gas component feels both gravitational and viscous forces. In addition, a halo force can be imposed for the purpose of stabilizing the disk. The code is a hybrid grid/smooth particle code. The gravitational forces are calculated on a Cartesian grid using a Fast Fourier Transform, while the gas viscous forces are calculated in a smooth particle manner. A mechanism for creating warm, featureless, stable disks is developed by taking moments of the collision less Boltzmann equation. In order to induce and control bar and spiral arm formation, the stabilizing stellar velocity dispersions are reduced in the center of the disk, but maintained in the outer regions. A bar forms naturally in the interior and the rotation of this bar helps maintain spiral structure in the outer gas disk. Realistic-looking spiral features are maintained in the gas component for as long as the models are calculated. A wide variety of bar and spiral structure can be formed by varying the size of the unstable central region, the rate of 'turn on', of the heating and the halo mass. We would like to test the model results by comparing

21 CFR 610.67 - Bar code label requirements.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 7 2011-04-01 2010-04-01 true Bar code label requirements. 610.67 Section 610.67 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) BIOLOGICS GENERAL BIOLOGICAL PRODUCTS STANDARDS Labeling Standards § 610.67 Bar code label requirements...

21 CFR 610.67 - Bar code label requirements.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 7 2010-04-01 2010-04-01 false Bar code label requirements. 610.67 Section 610.67 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) BIOLOGICS GENERAL BIOLOGICAL PRODUCTS STANDARDS Labeling Standards § 610.67 Bar code label requirements...

The lepton flavor violating exclusive b bar → s bar ℓi- ℓj+ decays in SUSY without R-parity

NASA Astrophysics Data System (ADS)

Sheng, Jin-Huan; Song, Jia-Jia; Wang, Ru-Min; Yang, Ya-Dong

2018-05-01

Inspired by the recent anomaly measurements of the lepton-flavor violating decays h → μτ and the lepton flavor non-universality in decays b bar → s bar ℓ-ℓ+, we investigate the lepton flavor violating exclusive b bar → s bar ℓi- ℓj+ (i ≠ j and ℓ = e , μ , τ) decays within supersymmetry. Relevant R-parity violating couplings are constrained by using the latest experimental upper limits on the branching ratios of Bs → ℓi- ℓj+ and B →K (*) ℓi- ℓ j + flavor changing neutral current processes, and we find that all relevant branching ratios are very sensitive to the moduli of the squark and sneutrino exchange coupling products. In addition, the constrained lepton number violating effects on the dilepton invariant mass spectra, the single lepton polarization asymmetries and the differential forward-backward asymmetries are also studied. These lepton-flavor violating B decays could be used for the search of lepton flavor violation at the running LHC and the forthcoming Belle-II.

Identification of number and type of cations in water-soluble Cs+ and Na+ calix[4]arene-bis-crown-6 complexes by using ESI-TOF-MS.

PubMed

Kumagai, Shogo; Hayashi, Kotaro; Kameda, Tomohito; Morohashi, Naoya; Hattori, Tetsutaro; Yoshioka, Toshiaki

2018-04-01

The treatment of cesium-contaminated wastewater has become one of the biggest issues. The selective Cs + removal from wastewater containing competitive alkali metal ions such as Na + is desired to reduce the volume of sludge. Therefore, the present work focused on water-soluble calix[4]arene-bis-crown-6 (W-BisC6) to selectively capture Cs + . For characterization of the complex, UV-vis spectroscopy is commonly used, however, due to the limited availability of information it can be hard to quickly identify the specific structures of some complexes. In this work, the electrospray ionization time of flight spectrometry (ESI-TOF-MS) is successfully utilized to identify the number and type of cations in W-BisC6-cation complexes. ESI-TOF-MS accurately recognized 4 types of complex (W-BisC6-Na + , W-BisC6-Cs + , W-BisC6-2Na + , W-BisC6-Na + -Cs + ), and the experimental and simulated results were almost perfectly matched. It also revealed the difficulty of W-BisC6-2Cs + complex formation under the present conditions. Thus, this technique is significantly helpful for rapid identification of the specific structures of complexes during Cs + -contaminated wastewater treatment. Copyright © 2018 Elsevier Ltd. All rights reserved.